WorldWideScience

Sample records for three-region conduction-controlled rewetting

  1. A three-region conduction-controlled rewetting analysis by the Heat Balance Integral Method

    International Nuclear Information System (INIS)

    Sahu, S.K.; Das, P.K.; Bhattacharyya, S.

    2009-01-01

    Conduction-controlled rewetting of two-dimensional objects is analyzed by the Heat Balance Integral Method (HBIM) considering three distinct regions: a dry region ahead of wet front, the sputtering region immediately behind the wet front and a continuous film region further upstream. The HBIM yields solutions for wet front velocity, sputtering length and temperature field with respect to wet front. Employing this method, it is seen that heat transfer mechanism is dependent upon two temperature parameters. One of them characterizes the initial wall temperature while the other specifies the range of temperature for sputtering region. Additionally, the mechanism of heat transfer is found to be dependent on two Biot numbers comprising a convective heat transfer in the wet region and a boiling heat transfer in the sputtering region. The present solution exactly matches with the one-dimensional analysis of K.H. Sun, G.E. Dix, C.L. Tien [Cooling of a very hot vertical surface by falling liquid film, ASME J. Heat Transf. 96 (1974) 126-131] for low Biot numbers. Good agreement with experimental results is also observed. (authors)

  2. Reflooding phase of the LOCA in PWRs. Part II: rewetting and liquid entrainment

    International Nuclear Information System (INIS)

    Elias, E.; Yadigaroglu, G.

    1978-01-01

    Surface rewetting and liquid-droplet entrainment play an important role in the analysis of the reflooding phase of the loss-of-coolant accident in pressurized-water reactors. The definitions and the various interpretations given to the rewetting temperature and the rewetting mechanisms of the fuel rods are discussed. Published models of the axial-conduction-controlled rewetting process include one-dimensional solutions in two axial regions, one-dimensional solutions in three axial regions with or without precursory cooling, one- and two-dimensional numerical-difference techniques using temperature-dependent heat-transfer coefficients, and analytical two-dimensional solutions. The basic physical assumptions and the numerical values assigned to the various parameters, as well as empirical rewetting correlations, are discussed. The physical mechanisms for liquid-droplet entrainment and analytical formulations of the critical gas velocity and of the droplet diameter at the onset of entrainment are reviewed

  3. Rewetting of composite slab

    International Nuclear Information System (INIS)

    Satapathy, A.K.; Singh, K.C.

    1996-01-01

    The process of re-establishment of wetting of hot surface is of practical importance in chemical, metallurgical and nuclear industries. Rewetting is considered in emergency core cooling in nuclear reactors in the event of postulated loss of coolant accident (LOCA). This paper deals with numerical solution of the two-dimensional quasi-static conduction controlled rewetting of an infinite parallel sided composite slab assuming perfect contact is maintained at the interface. On the wetted side upstream of the quench front, a constant heat transfer coefficient is assumed. The downstream of quench front and unwetted side of slab are supposed to be adiabatic. The solution gives the quench front temperature as a function of various model parameters such as Peclet number, wet side Blot number, dimensionless thickness of slab and cladding to fuel ratio of thermal conductivities. The results show that for large values of rewetting velocities, the dimensionless rewetting temperature is unaffected by fuel properties for all values of Blot numbers. (author). 7 refs., 2 tabs., 1 fig

  4. Rewetting of a hot metallic wall by liquid spray

    International Nuclear Information System (INIS)

    Castiglia, F.; Giardina, M.; Lombardo, C.

    2005-01-01

    Full text of publication follows: Rewetting is the re-establishment of liquid in contact with a hot dried surface, whose initial temperature is higher than the so-called 'rewetting temperature'. This phenomenology is of interest in many industrial processes, for example: in metallurgical quenching, in electronic equipments cooling, in cryogenic processes, in preserving the integrity of toxic and dangerous substances metallic containers endangered by a hypothetical fire. Moreover it is essential for the re-establishment of normal and safe temperature levels following rod cluster dryout or hypothesized loss of coolant accidents (LOCAs) in nuclear reactors. In spite of the large amount of experimental and theoretical work done in the past decades, the above depicted phenomenology still deserves further clarifications and deepening. For this reason, recently at the Institute of Energetic Thermal-Fluid Dynamics of ENEA (Ente per le Nuove Tecnologie, l'Energia e l'Ambiente, at Casaccia, Italy), experimental researches have been carried out on the rewetting of vertical surfaces, at ambient pressure and various water flow rates by spraying subcooled water at the top. Spraying devices of various configuration, able to supply water drops of uniform diameter, have been used [1]. As it is known when, following the drops impact in some region at the top of the surface the temperature is lowered below the rewetting temperature, a liquid falling film forms, the front of which advances with a velocity ( the so called 'rewetting velocity'), limited by the rapidity by which the heat is conducted into the solid (conduction controlled rewetting). In the past, about the rewetting the researchers of Department of Nuclear Engineering of the University of Palermo have carried out an extensive theoretical work and more recently, have proposed a semi-theoretical model which proved successful in correlating a lot of experimental data [2]. This model has been suitably modified in order to

  5. A general one-dimensional model for conduction-controlled rewetting of a surface

    International Nuclear Information System (INIS)

    Elias, E.; Yadigaroglu, G.

    1977-01-01

    A computer-oriented analytical method for predicting the rewetting rate of a hot dry wall is proposed. The wall, which is modeled as a thin flat plate with internal heat generation, receives a variable heat flux from one side while it is cooled from the other side. The model accounts for the large variations of the heat transfer coefficient near the wet front and for the temperature dependence of the thermal and physical properties of the wall. The one-dimensional heat-conduction equation is solved by dividing the quenching zone into small segments of arbitrary temperature increment and constant properties and heat transfer coefficient. A trial-and-error method is developed to predict the velocity of the wet front, the length of the quenching zone and the temperature profile. The one-dimensional models of other authors can be obtained as particular cases of the present model. (Auth.)

  6. Rewetting and liquid entrainment during reflooding: state of the art

    International Nuclear Information System (INIS)

    Elias, E.; Yadigaroglu, G.

    1977-05-01

    Considerable interest has recently been generated in the problems of surface rewetting and the physics of liquid droplet entrainment due to their role in light water nuclear reactor safety. Published models of the rewetting process include simple one-dimensional solutions in two axial regions, one-dimensional solutions in three axial regions with or without precursory cooling, one- and two-dimensional numerical-difference techniques using temperature dependent heat transfer coefficients, and analytical two-dimensional solutions. The basic assumptions of these models and the numerical values assigned to the various parameters, as well as empirical rewetting correlations, are discussed. The various mechanisms for liquid droplet entrainment and analytical formulations of the critical gas velocity and of the droplet diameter at the onset of entrainment are reviewed

  7. Rewetting of a hot metallic wall by liquid spray

    Energy Technology Data Exchange (ETDEWEB)

    Castiglia, F.; Giardina, M.; Lombardo, C. [University of Palermo, Department of Nuclear Engineering, V.le delle Scienze, 90128 Palermo (Italy)

    2005-07-01

    Full text of publication follows: Rewetting is the re-establishment of liquid in contact with a hot dried surface, whose initial temperature is higher than the so-called 'rewetting temperature'. This phenomenology is of interest in many industrial processes, for example: in metallurgical quenching, in electronic equipments cooling, in cryogenic processes, in preserving the integrity of toxic and dangerous substances metallic containers endangered by a hypothetical fire. Moreover it is essential for the re-establishment of normal and safe temperature levels following rod cluster dryout or hypothesized loss of coolant accidents (LOCAs) in nuclear reactors. In spite of the large amount of experimental and theoretical work done in the past decades, the above depicted phenomenology still deserves further clarifications and deepening. For this reason, recently at the Institute of Energetic Thermal-Fluid Dynamics of ENEA (Ente per le Nuove Tecnologie, l'Energia e l'Ambiente, at Casaccia, Italy), experimental researches have been carried out on the rewetting of vertical surfaces, at ambient pressure and various water flow rates by spraying subcooled water at the top. Spraying devices of various configuration, able to supply water drops of uniform diameter, have been used [1]. As it is known when, following the drops impact in some region at the top of the surface the temperature is lowered below the rewetting temperature, a liquid falling film forms, the front of which advances with a velocity ( the so called 'rewetting velocity'), limited by the rapidity by which the heat is conducted into the solid (conduction controlled rewetting). In the past, about the rewetting the researchers of Department of Nuclear Engineering of the University of Palermo have carried out an extensive theoretical work and more recently, have proposed a semi-theoretical model which proved successful in correlating a lot of experimental data [2]. This model has been

  8. Self-rewetting fluids with suspended carbon nanostructures.

    Science.gov (United States)

    Savino, R; Di Paola, R; Gattia, D Mirabile; Marazzi, R; Antisari, M Vittori

    2011-10-01

    Thermal management is very important in modern electronic systems. Recent researches have been dedicated to the study of the heat transfer performances of binary or multi-component heat transfer fluids with peculiar surface tension properties and in particular to "self-rewetting fluids," i.e., liquids with a surface tension increasing with temperature and concentration. Thermophysical properties like surface tension, wettability and thermal conductivity, at different temperatures, have been measured not only for binary mixtures, but also for a number of ternary aqueous solutions with relatively low freezing point and for nanoparticles suspensions (so called nanofluids). Some of them interestingly exhibit the same anomalous positive surface tension gradient with temperature as binary self-rewetting solutions. Since in the course of liquid/vapour phase change, self-rewetting fluids behaviour induces a rather strong liquid inflow (caused by both temperature and concentration gradients) from the cold region (where liquid condensates) to the hot evaporator region, several interesting applications may be envisaged, e.g., the development of advanced wickless heat pipes for utilization in reduced gravity environments. The present work is dedicated to the study of the thermophysical properties of nanofluids based on water/alcohol solutions with suspended carbon nanostructures, in particular single-wall carbon nanohorns (SWNH), synthesised by an homemade apparatus with an AC arc discharge in open air. The potential interest of the proposed studies stems from the large number of possible industrial applications, including space technologies and terrestrial applications, such as cooling of electronic components.

  9. Influence on rewetting temperature and wetting delay during rewetting rod bundle by various radial jet models

    Energy Technology Data Exchange (ETDEWEB)

    Debbarma, Ajoy; Pandey, Krishna Murari [National Institute of Technology, Assam (India). Dept. of Mechanical Engineering

    2016-03-15

    Numerical investigation of the rewetting of single sector fuel assembly of Advanced Heavy Water Reactor (AHWR) has been carried out to exhibit the effect of coolant jet diameters (2, 3 and 4 mm) and jet directions (Model: M, X and X2). The rewetting phenomena with various jet models are compared on the basis of rewetting temperature and wetting delay. Temperature-time curve have been evaluated from rods surfaces at different circumference, radial and axial locations of rod bundle. The cooling curve indicated the presence of vapor in respected location, where it prevents the contact between the firm and fluid phases. The peak wall temperature represents as rewetting temperature. The time period observed between initial to rewetting temperature point is wetting delay. It was noted that as improved in various jet models, rewetting temperature and wetting delay reduced, which referred the coolant stipulation in the rod bundle dominant vapor formation.

  10. Influence on rewetting temperature and wetting delay during rewetting rod bundle by various radial jet models

    International Nuclear Information System (INIS)

    Debbarma, Ajoy; Pandey, Krishna Murari

    2016-01-01

    Numerical investigation of the rewetting of single sector fuel assembly of Advanced Heavy Water Reactor (AHWR) has been carried out to exhibit the effect of coolant jet diameters (2, 3 and 4 mm) and jet directions (Model: M, X and X2). The rewetting phenomena with various jet models are compared on the basis of rewetting temperature and wetting delay. Temperature-time curve have been evaluated from rods surfaces at different circumference, radial and axial locations of rod bundle. The cooling curve indicated the presence of vapor in respected location, where it prevents the contact between the firm and fluid phases. The peak wall temperature represents as rewetting temperature. The time period observed between initial to rewetting temperature point is wetting delay. It was noted that as improved in various jet models, rewetting temperature and wetting delay reduced, which referred the coolant stipulation in the rod bundle dominant vapor formation.

  11. Rewetting during bottom flooding

    International Nuclear Information System (INIS)

    Pearson, K.G.

    1984-11-01

    A qualitative description of the rewetting process during bottom reflooding of a PWR is presented. Rewetting is seen as the end product of a path taken over a heat transfer surface which defines how the surface heat flux varies with surface temperature and with distance from the rewetting front. The main components are liquid contact, vapour convection and thermal radiation. In this paper the general topography of the heat transfer surface is deduced from consideration of the ways in which the conditions of the vapour and liquid phases in the flow are expected to vary with distance from the rewetting front. The deduced surface has a heat transfer ridge which decreases in height, and whose steep face moves to lower temperatures, with increasing distance from the rewetting front, and a valley which becomes negative with increasing distance. There is a different surface for each position along a subchannel, strongly influenced by the proximity of spacer grids, and by whether these grids are wet or dry. The form of this family of heat transfer surfaces is used to explain the phenomena of reflooding of clusters of heated rods. (U.K.)

  12. CFD analysis of rewetting of a single sector AHWR fuel cluster with changing jet directions

    Energy Technology Data Exchange (ETDEWEB)

    Debbarma, Ajoy, E-mail: ajoy@debbarma.me; Pandey, Krishna Murari, E-mail: kmpandey2001@yahoo.com

    2016-11-15

    Highlights: • CFD analysis of three modes of jet impingement in AHWR fuel cluster is analyzed. • Single sector (9 rod bundle) of AHWR has been analyzed with ANSYS 14.0-CFX. • It is observed that the wetting delay gets reduced significantly by proposed jet models. - Abstract: The transient numerical analysis of the rewetting of Advanced Heavy Water Reactor (AHWR) fuel assembly with jet impingement has been conducted. The present study is concerned with three different types of jet impingement directions, Model: M is the existing design of AHWR and other two Model: X and X2 was introduced in the study and compared with an existing model of AHWR. The present investigation aims to study thermo-rewetting behavior with respect to the coolant jet impingement directions. The computational results are validated with available experimental data. It is observed that the wetting delay has been reduced significantly with the proposed jet models and the jet direction has been an effective parameter in increasing the rewetting performance.

  13. Multiyear greenhouse gas balances at a rewetted temperate peatland.

    Science.gov (United States)

    Wilson, David; Farrell, Catherine A; Fallon, David; Moser, Gerald; Müller, Christoph; Renou-Wilson, Florence

    2016-12-01

    Drained peat soils are a significant source of greenhouse gas (GHG) emissions to the atmosphere. Rewetting these soils is considered an important climate change mitigation tool to reduce emissions and create suitable conditions for carbon sequestration. Long-term monitoring is essential to capture interannual variations in GHG emissions and associated environmental variables and to reduce the uncertainty linked with GHG emission factor calculations. In this study, we present GHG balances: carbon dioxide (CO 2 ), methane (CH 4 ) and nitrous oxide (N 2 O) calculated for a 5-year period at a rewetted industrial cutaway peatland in Ireland (rewetted 7 years prior to the start of the study); and compare the results with an adjacent drained area (2-year data set), and with ten long-term data sets from intact (i.e. undrained) peatlands in temperate and boreal regions. In the rewetted site, CO 2 exchange (or net ecosystem exchange (NEE)) was strongly influenced by ecosystem respiration (R eco ) rather than gross primary production (GPP). CH 4 emissions were related to soil temperature and either water table level or plant biomass. N 2 O emissions were not detected in either drained or rewetted sites. Rewetting reduced CO 2 emissions in unvegetated areas by approximately 50%. When upscaled to the ecosystem level, the emission factors (calculated as 5-year mean of annual balances) for the rewetted site were (±SD) -104 ± 80 g CO 2 -C m -2  yr -1 (i.e. CO 2 sink) and 9 ± 2 g CH 4 -C m -2  yr -1 (i.e. CH 4 source). Nearly a decade after rewetting, the GHG balance (100-year global warming potential) had reduced noticeably (i.e. less warming) in comparison with the drained site but was still higher than comparative intact sites. Our results indicate that rewetted sites may be more sensitive to interannual changes in weather conditions than their more resilient intact counterparts and may switch from an annual CO 2 sink to a source if triggered by slightly drier

  14. Effects of soil rewetting and thawing on soil gas fluxes: a review of current literature and suggestions for future research

    Directory of Open Access Journals (Sweden)

    D.-G. Kim

    2012-07-01

    Full Text Available The rewetting of dry soils and the thawing of frozen soils are short-term, transitional phenomena in terms of hydrology and the thermodynamics of soil systems. The impact of these short-term phenomena on larger scale ecosystem fluxes is increasingly recognized, and a growing number of studies show that these events affect fluxes of soil gases such as carbon dioxide (CO2, methane (CH4, nitrous oxide (N2O, ammonia (NH3 and nitric oxide (NO. Global climate models predict that future climatic change is likely to alter the frequency and intensity of drying-rewetting events and thawing of frozen soils. These future scenarios highlight the importance of understanding how rewetting and thawing will influence dynamics of these soil gases. This study summarizes findings using a new database containing 338 studies conducted from 1956 to 2011, and highlights open research questions. The database revealed conflicting results following rewetting and thawing in various terrestrial ecosystems and among soil gases, ranging from large increases in fluxes to non-significant changes. Studies reporting lower gas fluxes before rewetting tended to find higher post-rewetting fluxes for CO2, N2O and NO; in addition, increases in N2O flux following thawing were greater in warmer climate regions. We discuss possible mechanisms and controls that regulate flux responses, and recommend that a high temporal resolution of flux measurements is critical to capture rapid changes in gas fluxes after these soil perturbations. Finally, we propose that future studies should investigate the interactions between biological (i.e., microbial community and gas production and physical (i.e., porosity, diffusivity, dissolution changes in soil gas fluxes, apply techniques to capture rapid changes (i.e., automated measurements, and explore synergistic experimental and modelling approaches.

  15. Solution to a fuel-and-cladding rewetting model

    International Nuclear Information System (INIS)

    Olek, S.

    1989-06-01

    A solution by the Wiener-Hopf technique is derived for a model for the rewetting of a nuclear fuel rod. The gap between the fuel and the cladding is modelled by an imperfect contact between the two. A constant heat transfer coefficient is assumed on the wet side, whereas the dry side is assumed to be adiabatic. The solution for the rewetting temperature is in the form of an integral whose integrand contains the model parameters, including the rewetting velocity. Numerical results are presented for a large number of these parameters. It is shown that there are such large values of the rewetting temperature and the gap resistance, or such low values of the initial wall temperature, for which the rewetting velocity is unaffected by the fuel properties. (author) l fig., 7 tabs., 17 refs

  16. Investigation on the rewetting temperature behavior in a vertical annulus geometry with uniform and cosine power distribution

    International Nuclear Information System (INIS)

    Cho, S.; Chun, S. Y.; Kim, B. D.; Park, J. K.; Baek, W. P.

    2005-01-01

    All theoretical predictions for the rewetting process by the various models based on one-, two- and three-dimensional analytical and numerical studies require the knowledge of the rewetting temperature. (Kim and Lee, 1979) Incorrectly assumed values of rewetting temperature could lead to serious errors in the analysis of the problem. This parameter was assumed to be constant by many researchers such as Martini et al. (1973), Yamanouchi (1968), and Yu et al. (1977). However, the rewetting temperature is not constant and depends on the physical properties of the test section and coolant flow condition. In the present study, experimental data on the rewetting temperature acquired in the present reflood test series are compared with the previous rewetting temperature correlations proposed by Berenson (1961), Henry (1974), and Kim and Lee (1979)

  17. Simulated drawdown and rewetting of littoral sediments

    DEFF Research Database (Denmark)

    Klamt, Anna-Marie; Reitzel, Kasper; Andersen, Frede Østergaard

    2016-01-01

    This study aims to answer the question if temporary drawdowns could be a beneficial restoration measure for endangered Lobelia lakes. Intact littoral sediment cores with and without plants were used to simulate a drawdown over an almost 5 months period and a subsequent rewetting. During drawdown...... dying of plants. Upon rewetting effluxes of total dissolved phosphorus and dissolved organic carbon were observed which are most likely attributable to the degraded plant material. A phosphorus uptake experiment with dried and rewetted sediment cores without plants showed that the initial high P binding...

  18. Analytical models for the rewetting of hot surfaces

    International Nuclear Information System (INIS)

    Olek, S.

    1988-10-01

    Some aspects concerning analytical models for the rewetting of hot surface are discussed. These include the problems with applying various forms of boundary conditions, compatibility of boundary conditions with the physics of the rewetting problems, recent analytical models, the use of the separation of variables method versus the Wiener-Hopf technique, and the use of transformations. The report includes an updated list of rewetting models as well as benchmark solutions in tabular form for several models. It should be emphasized that this report is not meant to cover the topic of rewetting models. It merely discusses some points which are less commonly referred to in the literature. 93 refs., 3 figs., 22 tabs

  19. Reflooding Experiment on BETA Test Loop: The Effects of Inlet Temperature on the Rewetting Velocity

    International Nuclear Information System (INIS)

    Khairul H; Anhar R Antariksawan; Edy Sumarno; Kiswanta; Giarno; Joko P; Ismu Handoyo

    2003-01-01

    Loss of Coolant Accident (LOCA) on Nuclear Reactor Plant is an important topic because this condition is a severe accident that can be postulated. The phenomenon of LOCA on Pressurized Water Reactor (PWR) can be divided in three stages, e.g.: blowdown, refill and reflood. In the view of Emergency Coolant System evaluation, the reflood is the most important stage. In this stage, an injection of emergency water coolant must be done in a way that the core can be flooded and the overheating can be avoid. The experiment of rewetting on BETA Test Loop had been conducted. The experiment using one heated rod of the test section to study effects of inlet temperature on the wetting velocity. Results of the series of experiments on 2,5 lt/min flow rate and variable of temperature : 28 o C, 38 o C, 50 o C, 58 o C it was noticed that for 58 o C inlet temperature of test section and 572 o C rod temperature the rewetting phenomenon has been observed. The time of refill was 32.81 sec and time of rewetting was 42.87 sec. (author)

  20. Measurement and analysis of the re-wetting front velocity during quench cooling of hot horizontal tubes

    Energy Technology Data Exchange (ETDEWEB)

    Takrouri, Kifah, E-mail: takroukj@mcmaster.ca [Department of Engineering Physics, McMaster University, 1280 Main Street West, Hamilton, Ontario L8S 4L7 (Canada); Luxat, John, E-mail: luxatj@mcmaster.ca [Department of Engineering Physics, McMaster University, 1280 Main Street West, Hamilton, Ontario L8S 4L7 (Canada); Hamed, Mohamed [Thermal Processing Laboratory (TPL), Department of Mechanical Engineering, McMaster University, 1280 Main Street West, Hamilton, Ontario L8S 4L7 (Canada)

    2017-01-15

    Highlights: • Two phase flow & re-wetting front velocity were studied for quench of hot tubes. • The velocity decreased as temperature difference between tube and coolant decreased. • Increasing surface curvature was found to decrease the re-wetting front velocity. • Increasing tube thermal conductivity decreased the velocity. • Correlations were developed to predict the front velocity. - Abstract: When a liquid is put into contact with a hot dry surface, there exists a maximum temperature called the re-wetting temperature below which the liquid is in actual contact with the surface. Re-wetting occurs after destabilization of a vapor film that exists between the hot surface and the liquid. If re-wetting is established at a location on the hot surface, a wet patch appears at that location and starts to spread to cover and cool the entire surface. The outer edge of the wet patch is called the re-wetting front and can proceed only if the surface ahead of it cools down to the re-wetting temperature. Study of re-wetting heat transfer is very important in nuclear reactor safety for limiting the extent of core damage during the early stages of severe accidents after loss of coolant accidents LOCA and is essential for predicting the rate at which the coolant cools an overheated core. One of the important parameters in re-wetting cooling is the velocity at which the re-wetting front moves on the surface. In this study, experimental tests were carried out to investigate the re-wetting front velocity on hot horizontal cylindrical tubes being cooled by a vertical rectangular water multi-jet system. Effects of initial surface temperature in the range 400–740 °C, water subcooling in the range 15–80 °C and jet velocity in the range 0.17–1.43 m/s on the re-wetting front velocity were investigated. The two-phase flow behavior was observed by using a high-speed camera. The re-wetting front velocity was found to increase by increasing water subcooling, decreasing

  1. Test facility for rewetting experiments at CDTN

    International Nuclear Information System (INIS)

    Rezende, Hugo C.; Mesquita, Amir Z.; Ladeira, Luiz C.D.; Santos, Andre A.C.

    2015-01-01

    One of the most important subjects in nuclear reactor safety analysis is the reactor core rewetting after a Loss-of-Coolant Accident (LOCA) in a Light Water Reactor LWR. Several codes for the prediction of the rewetting evolution are under development based on experimental results. In a Pressurized Water Reactor (PWR) the reflooding phase of a LOCA is when the fuel rods are rewetted from the bottom of the core to its top after having been totally uncovered and dried out. Out-of-pile reflooding experiments performed with electrical heated fuel rod simulators show different quench behavior depending the rods geometry. A test facility for rewetting experiments (ITR - Instalacao de Testes de Remolhamento) has been constructed at the Thermal Hydraulics Laboratory of the Centro de Desenvolvimento da Tecnologia Nuclear (CDTN), with the objective of performing investigations on basic phenomena that occur during the reflood phase of a LOCA in a PWR, using tubular and annular test sections. This paper presents the design aspects of the facility, and the current stage of the works. The mechanical aspects of the installation as its instrumentation are described. Two typical tests are presented and results compered with theoretical calculations using computer code. (author)

  2. Test facility for rewetting experiments at CDTN

    Energy Technology Data Exchange (ETDEWEB)

    Rezende, Hugo C.; Mesquita, Amir Z.; Ladeira, Luiz C.D.; Santos, Andre A.C., E-mail: hcr@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (SETRE/CDTN/CNEN-MG), Belo Horizonte, MG (Brazil). Servico de Tecnologia de Reatores

    2015-07-01

    One of the most important subjects in nuclear reactor safety analysis is the reactor core rewetting after a Loss-of-Coolant Accident (LOCA) in a Light Water Reactor LWR. Several codes for the prediction of the rewetting evolution are under development based on experimental results. In a Pressurized Water Reactor (PWR) the reflooding phase of a LOCA is when the fuel rods are rewetted from the bottom of the core to its top after having been totally uncovered and dried out. Out-of-pile reflooding experiments performed with electrical heated fuel rod simulators show different quench behavior depending the rods geometry. A test facility for rewetting experiments (ITR - Instalacao de Testes de Remolhamento) has been constructed at the Thermal Hydraulics Laboratory of the Centro de Desenvolvimento da Tecnologia Nuclear (CDTN), with the objective of performing investigations on basic phenomena that occur during the reflood phase of a LOCA in a PWR, using tubular and annular test sections. This paper presents the design aspects of the facility, and the current stage of the works. The mechanical aspects of the installation as its instrumentation are described. Two typical tests are presented and results compered with theoretical calculations using computer code. (author)

  3. Safety rewetting process by imersion

    International Nuclear Information System (INIS)

    Pereira, V.Q.

    1981-09-01

    A theoretical and experimental study of the slow transient phenomena encountered during emergency core cooling rewetting of pressurized water reactors was done. To perform this study a low pressure and low heat flux water loop was used, with two basic tests sections, one tubular and another annular. After being heated by the Joule effect, the test section was quenched at a constant flow rate by bottom flooding of water at room temperature. The effects of wall temperature and fluid flow rate in tjhe performance of the rewetting process were investigated. Our results were in good agreement with those obtained by other laboratories. (Author) [pt

  4. Effects of arbuscular mycorrhizal fungi and soil nutrient addition on the growth of Phragmites australis under different drying-rewetting cycles.

    Science.gov (United States)

    Liang, Jin-Feng; An, Jing; Gao, Jun-Qin; Zhang, Xiao-Ya; Yu, Fei-Hai

    2018-01-01

    The frequency of soil drying-rewetting cycles is predicted to increase under future global climate change, and arbuscular mycorrhizal fungi (AMF) are symbiotic with most plants. However, it remains unknown how AMF affect plant growth under different frequencies of soil drying-rewetting cycles. We subjected a clonal wetland plant Phragmites australis to three frequencies of drying-rewetting cycles (1, 2, or 4 cycles), two nutrient treatments (with or without), and two AMF treatments (with or without) for 64 days. AMF promoted the growth of P. australis, especially in the 2 cycles of the drying-rewetting treatment. AMF had a significant positive effect on leaf mass and number of ramets in the 2 cycles of the drying-rewetting treatment with nutrient addition. In the 2 cycles of drying-rewetting treatment without nutrient addition, AMF increased leaf area and decreased belowground to aboveground biomass ratio. These results indicate that AMF may assist P. australis in coping with medium frequency of drying-rewetting cycles, and provide theoretical guidance for predicting how wetland plants respond to future global climate change.

  5. Summertime greenhouse gas fluxes from an urban bog undergoing restoration through rewetting

    Directory of Open Access Journals (Sweden)

    A. Christen

    2016-04-01

    Full Text Available Rewetting can promote the ecological recovery of disturbed peatland ecosystems and may help to revert these ecosystems to carbon dioxide (CO2 sinks. However, rewetting of disturbed peatlands can also cause substantial emissions of methane (CH4 and possibly nitrous oxide (N2O. This study quantified summertime emissions of the three major long-lived greenhouse gases (GHGs CO2, CH4 and N2O; from undisturbed, disturbed and rewetted soils in the Burns Bog Ecological Conservancy Area (BBECA, a 20 km2 urban bog located in Delta, British Columbia, Canada. Four sites were chosen that represent different stages before or after ecological recovery in the BBECA: (i a relatively undisturbed scrub pine / Sphagnum / low shrub ecosystem; (ii a Rhynchospora alba / Sphagnum ecosystem that was disturbed by peat mining more than 65 years ago; (iii a R. alba / Dulichium arundinaceum ecosystem that was disturbed by peat mining 50 years ago and rewetted five years ago; and (iv a disturbed and rewetted surface with little vegetation cover that was cleared of vegetation 16 years ago and rewetted two years ago. The GHG fluxes from soils and ground vegetation were measured at all sites during June–August 2014, using a portable non-steady-state chamber system for CO2 and syringe sampling and laboratory analysis for CH4 and N2O fluxes. All four sites exhibited net GHG emissions into the atmosphere, dominated by CH4, which contributed 81–98 % of net CO2 equivalent (CO2e emissions. Overall, the median CH4 flux for all measurements and sites was ~74 mg m-2 day-1 (~30–410 mg m-2 day-1, 25th–75th percentiles. Fluxes in the rewetted (water-saturated sedge ecosystem were highest, with a quarter of the values higher than 3,000 mg m-2 day-1 (median 78 mg m-2 day-1. Exchange of CO2 due to photosynthesis and respiration was of secondary importance compared to soil CH4 emissions. Continuous CO2 flux measurements using the eddy covariance approach in the disturbed and rewetted R

  6. Greenhouse gas emissions from rewetted bog peat extraction sites and a Sphagnum cultivation site in Northwest Germany

    Science.gov (United States)

    Beyer, C.; Höper, H.

    2014-03-01

    During the last three decades, an increasing area of drained peatlands was rewetted. This was done with the objective to convert these sites from sources back to sinks or, at least, to much smaller sources of greenhouse gases (GHG). However, available data is still scarce, especially on the long-term climatic effects of rewetting of temperate bogs. Moreover, first field trials are established for Sphagnum cultivating (paludiculture) on wet bog sites and an assessment of the climate impact of such measures has not been studied yet. We conducted a field study on the exchange of carbon dioxide, methane and nitrous oxide at three rewetted sites with a gradient from dry to wet conditions and at a Sphagnum cultivation site in NW Germany over more than two years. Gas fluxes were measured using transparent and opaque closed chambers. The ecosystem respiration (CO2) and the net ecosystem exchange (CO2) were modelled in high time resolution using automatically monitored climate data. Measured and modelled values fit very well together (R2 between 0.88 and 0.98). Annually cumulated gas flux rates, net ecosystem carbon balances (NECB) and global warming potential (GWP) balances were determined. The annual net ecosystem exchange (CO2) varied strongly at the rewetted sites (from -201.7 ± 126.8 to 29.7 ± 112.7 g CO2-C m-2 a-1) due to different weather conditions, water level and vegetation. The Sphagnum cultivation site was a sink of CO2 (-118.8 ± 48.1 and -78.6 ± 39.8 g CO2-C m-2 a-1). The yearly CH4 balances ranged between 16.2 ± 2.2 and 24.2 ± 5.0 g CH4-C m-2 a-1 at two inundated sites, while one rewetted site with a comparatively low water level and the Sphagnum farming site show CH4 fluxes close to zero. The net N2O fluxes were low and not significantly different between the four sites. The annual NECB at the rewetted sites was between -183.8 ± 126.9 and 51.6 ± 112.8 g CO2-C m-2 a-1 and at the Sphagnum cultivating site -114.1 ± 48.1 and -75.3 ± 39.8 g CO2-C m-2 a-1

  7. Greenhouse gas exchange of rewetted bog peat extraction sites and a Sphagnum cultivation site in northwest Germany

    Science.gov (United States)

    Beyer, C.; Höper, H.

    2015-04-01

    During the last decades an increasing area of drained peatlands has been rewetted. Especially in Germany, rewetting is the principal treatment on cutover sites when peat extraction is finished. The objectives are bog restoration and the reduction of greenhouse gas (GHG) emissions. The first sites were rewetted in the 1980s. Thus, there is a good opportunity to study long-term effects of rewetting on greenhouse gas exchange, which has not been done so far on temperate cutover peatlands. Moreover, Sphagnum cultivating may become a new way to use cutover peatlands and agriculturally used peatlands as it permits the economical use of bogs under wet conditions. The climate impact of such measures has not been studied yet. We conducted a field study on the exchange of carbon dioxide, methane and nitrous oxide at three rewetted sites with a gradient from dry to wet conditions and at a Sphagnum cultivation site in NW Germany over the course of more than 2 years. Gas fluxes were measured using transparent and opaque closed chambers. The ecosystem respiration (CO2) and the net ecosystem exchange (CO2) were modelled at a high temporal resolution. Measured and modelled values fit very well together. Annually cumulated gas flux rates, net ecosystem carbon balances (NECB) and global warming potential (GWP) balances were determined. The annual net ecosystem exchange (CO2) varied strongly at the rewetted sites (from -201.7 ± 126.8 to 29.7± 112.7g CO2-C m-2 a-1) due to differing weather conditions, water levels and vegetation. The Sphagnum cultivation site was a sink of CO2 (-118.8 ± 48.1 and -78.6 ± 39.8 g CO2-C m-2 a-1). The annual CH4 balances ranged between 16.2 ± 2.2 and 24.2 ± 5.0g CH4-C m-2 a-1 at two inundated sites, while one rewetted site with a comparatively low water level and the Sphagnum farming site show CH4 fluxes close to 0. The net N2O fluxes were low and not significantly different between the four sites. The annual NECB was between -185.5 ± 126.9 and 49

  8. Self-rewetting carbon nanofluid as working fluid for space and terrestrial heat pipes

    Science.gov (United States)

    Di Paola, R.; Savino, R.; Mirabile Gattia, D.; Marazzi, R.; Vittori Antisari, M.

    2011-11-01

    Thermal management is very important in modern electronic systems. Recent researches have been dedicated to the study of the heat transfer performances of binary heat transfer fluids with peculiar surface tension properties and in particular to that of "self-rewetting fluids", i.e., liquids with a surface tension increasing with temperature and concentration. Since in the course of liquid/vapor-phase change, self-rewetting fluids behavior induces a rather strong liquid inflow (caused by both temperature and concentration gradients) from the cold region (where liquid condensates) to the hot evaporator region, this fluids have been proposed and investigated as new heat transfer fluids for advanced heat transfer devices, e.g., heat pipes or heat spreaders for terrestrial and space applications (Savino et al. in Space Technol 25(1):59-61, 2009). The present work is dedicated to the study of the thermophysical properties of a new class of heat transfer fluids based on water/alcohol solutions with suspended carbon nanostructures, in particular single-wall carbon nanohorns (SWNH), synthesized by a homemade apparatus with an AC arc discharge in open air (Mirabile Gattia et al. in Nanotechnology 18:255604, 2007). SWNHs are cone-shaped nanoparticles with diameters between 1 and 5 nm and lengths in the range of 20-100 nm. SWNHs could be found in the form of quite-spherical aggregates with diameters ranging from 20 to 100 nm. The paper also discusses the results of these investigations and laboratory characterization tests of different heat pipes, including reference ordinary heat pipes and innovative pipes filled with self-rewetting fluids and self-rewetting nanofluids. The potential interest of the proposed studies stems from the large number of possible industrial applications, including space technologies and terrestrial applications, such as cooling of electronic components.

  9. Self-rewetting carbon nanofluid as working fluid for space and terrestrial heat pipes

    International Nuclear Information System (INIS)

    Di Paola, R.; Savino, R.; Mirabile Gattia, D.; Marazzi, R.; Vittori Antisari, M.

    2011-01-01

    Thermal management is very important in modern electronic systems. Recent researches have been dedicated to the study of the heat transfer performances of binary heat transfer fluids with peculiar surface tension properties and in particular to that of “self-rewetting fluids”, i.e., liquids with a surface tension increasing with temperature and concentration. Since in the course of liquid/vapor-phase change, self-rewetting fluids behavior induces a rather strong liquid inflow (caused by both temperature and concentration gradients) from the cold region (where liquid condensates) to the hot evaporator region, this fluids have been proposed and investigated as new heat transfer fluids for advanced heat transfer devices, e.g., heat pipes or heat spreaders for terrestrial and space applications (Savino et al. in Space Technol 25(1):59–61, 2009). The present work is dedicated to the study of the thermophysical properties of a new class of heat transfer fluids based on water/alcohol solutions with suspended carbon nanostructures, in particular single-wall carbon nanohorns (SWNH), synthesized by a homemade apparatus with an AC arc discharge in open air (Mirabile Gattia et al. in Nanotechnology 18:255604, 2007). SWNHs are cone-shaped nanoparticles with diameters between 1 and 5 nm and lengths in the range of 20–100 nm. SWNHs could be found in the form of quite-spherical aggregates with diameters ranging from 20 to 100 nm. The paper also discusses the results of these investigations and laboratory characterization tests of different heat pipes, including reference ordinary heat pipes and innovative pipes filled with self-rewetting fluids and self-rewetting nanofluids. The potential interest of the proposed studies stems from the large number of possible industrial applications, including space technologies and terrestrial applications, such as cooling of electronic components.

  10. Conception of a model for the description of the rewetting phase of reactor fuel pins following a loss-of-coolant accident

    International Nuclear Information System (INIS)

    Hinderer, B.; Schuetzle, R.

    1976-10-01

    The aim of the present paper has been the development of a model describing rewetting of fuel rods in the reflood phase after a loss of coolant accident of a reactor. Because a suitable solution to the problem could not be found an appropriate model has been implemented into an IKE computer program for transient, two-dimensional heat conductance for a cylindrical rod. Developing this model experimental results of up-to-date literature were used. Remarkable is that very small meshes are necessary around the rewetting front to calculate the rewetting velocity which is strongly dependent on the quench temperature. (orig.) [de

  11. High methane emissions dominate annual greenhouse gas balances 30 years after bog rewetting

    Science.gov (United States)

    Vanselow-Algan, M.; Schmidt, S. R.; Greven, M.; Fiencke, C.; Kutzbach, L.; Pfeiffer, E.-M.

    2015-02-01

    Natural peatlands are important carbon sinks and sources of methane (CH4). In contrast, drained peatlands turn from a carbon sink to a carbon source and potentially emit nitrous oxide (N2O). Rewetting of peatlands thus implies climate change mitigation. However, data about the time span that is needed for the re-establishment of the carbon sink function by restoration is scarce. We therefore investigated the annual greenhouse gas (GHG) balances of three differently vegetated bog sites 30 years after rewetting. All three vegetation communities turned out to be sources of carbon dioxide (CO2) ranging between 0.6 ± 1.43 t CO2 ha-2 yr-1 (Sphagnum-dominated vegetation) and 3.09 ± 3.86 t CO2 ha-2 yr-1 (vegetation dominated by heath). While accounting for the different global warming potential (GWP) of the three greenhouse gases, the annual GHG balance was calculated. Emissions ranged between 25 and 53 t CO2-eq ha-1 yr-1 and were dominated by large emissions of CH4 (22 up to 51 t CO2-eq ha-1 yr-1), while highest rates were found at purple moor grass (Molinia caerulea) stands. These are to our knowledge the highest CH4 emissions so far reported for bog ecosystems in temperate Europe. As the restored area was subject to large fluctuations in water table, we conclude that the high CH4 emission rates were caused by a combination of both the temporal inundation of the easily decomposable plant litter of this grass species and the plant-mediated transport through its tissues. In addition, as a result of the land use history, the mixed soil material can serve as an explanation. With regards to the long time span passed since rewetting, we note that the initial increase in CH4 emissions due to rewetting as described in the literature is not limited to a short-term period.

  12. Do drying and rewetting cycles modulate effects of sulfadiazine spiked manure in soil?

    Science.gov (United States)

    Jechalke, Sven; Radl, Viviane; Schloter, Michael; Heuer, Holger; Smalla, Kornelia

    2016-05-01

    Naturally occurring drying-rewetting events in soil have been shown to affect the dissipation of veterinary antibiotics entering soil by manure fertilization. However, knowledge of effects on the soil microbial community structure and resistome is scarce. Here, consequences of drying-rewetting cycles on effects of sulfadiazine (SDZ) in soil planted with Dactylis glomerata L. were investigated in microcosms. Manure containing SDZ or not was applied to the pregrown grass and incubated for 56 days in a climate chamber. Water was either added daily or reduced during two drying events of 7 days, each followed by a recovery phase. Total community DNA was analyzed to reveal the effects on the bacterial community structure and on the abundance of sul1, sul2, intI1 ,intI2, qacE+qacEΔ1, traN and korB genes relative to 16S rRNA genes. 16S rRNA gene-based DGGE fingerprints indicated that drying-rewetting cycles modulated the effects of SDZ on the bacterial community structure in the soil. Furthermore, the SDZ treatment increased the relative abundance of sulfonamide resistance and integrase genes compared to the control. However, this increase was not different between moisture regimes, indicating that drying-rewetting had only a negligible effect on the selection of the resistome by SDZ in the manured soil. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  13. Short-Term Effects of Drying-Rewetting and Long-Term Effects of Nutrient Loading on Periphyton N:P Stoichiometry

    Directory of Open Access Journals (Sweden)

    Andres D. Sola

    2018-01-01

    Full Text Available Nitrogen (N and phosphorus (P concentrations and N:P ratios critically influence periphyton productivity and nutrient cycling in aquatic ecosystems. In coastal wetlands, variations in hydrology and water source (fresh or marine influence nutrient availability, but short-term effects of drying and rewetting and long-term effects of nutrient exposure on periphyton nutrient retention are uncertain. An outdoor microcosm experiment simulated short-term exposure to variation in drying-rewetting frequency on periphyton mat nutrient retention. A 13-year dataset from freshwater marshes of the Florida Everglades was examined for the effect of long-term proximity to different N and P sources on mat-forming periphyton nutrient standing stocks and stoichiometry. Field sites were selected from one drainage with shorter hydroperiod and higher connectivity to freshwater anthropogenic nutrient supplies (Taylor Slough/Panhandle, TS/Ph and another drainage with longer hydroperiod and higher connectivity to marine nutrient supplies (Shark River Slough, SRS. Total P, but not total N, increased in periphyton mats exposed to both low and high drying-rewetting frequency with respect to the control mats in our experimental microcosm. In SRS, N:P ratios slightly decreased downstream due to marine nutrient supplies, while TS/Ph increased. Mats exposed to short-term drying-rewetting had higher nutrient retention, similar to nutrient standing stocks from long-term field data. Periphyton mat microbial communities may undergo community shifts upon drying-rewetting and chronic exposure to nutrient loads. Additional work on microbial species composition may further explain how periphyton communities interact with drying-rewetting dynamics to influence nutrient cycling and retention in wetlands.

  14. A Pilot Study: The Efficacy of Virgin Coconut Oil as Ocular Rewetting Agent on Rabbit Eyes

    Directory of Open Access Journals (Sweden)

    Haliza Abdul Mutalib

    2015-01-01

    Full Text Available Purpose. An open-label pilot study of virgin coconut oil (VCO was conducted to determine the safety of the agent as ocular rewetting eye drops on rabbits. Methods. Efficacy of the VCO was assessed by measuring NIBUT, anterior eye assessment, corneal staining, pH, and Schirmer value before instillation and at 30 min, 60 min, and two weeks after instillation. Friedman test was used to analyse any changes in all the measurable variables over the period of time. Results. Only conjunctival redness with instillation of saline agent showed significant difference over the period of time (P0.05. There were no changes in the NIBUT, limbal redness, palpebral conjunctiva redness, corneal staining, pH, and Schirmer value over the period of time for each agent (P>0.05. Conclusion. VCO acts as safe rewetting eye drops as it has shown no significant difference in the measurable parameter compared to commercial brand eye drops and saline. These study data suggest that VCO is safe to be used as ocular rewetting agent on human being.

  15. High methane emissions dominated annual greenhouse gas balances 30 years after bog rewetting

    Science.gov (United States)

    Vanselow-Algan, M.; Schmidt, S. R.; Greven, M.; Fiencke, C.; Kutzbach, L.; Pfeiffer, E.-M.

    2015-07-01

    Natural peatlands are important carbon sinks and sources of methane (CH4). In contrast, drained peatlands turn from a carbon sink to a carbon source and potentially emit nitrous oxide (N2O). Rewetting of peatlands thus potentially implies climate change mitigation. However, data about the time span that is needed for the re-establishment of the carbon sink function by restoration are scarce. We therefore investigated the annual greenhouse gas (GHG) balances of three differently vegetated sites of a bog ecosystem 30 years after rewetting. All three vegetation communities turned out to be sources of carbon dioxide (CO2) ranging between 0.6 ± 1.43 t CO2 ha-2 yr-1 (Sphagnum-dominated vegetation) and 3.09 ± 3.86 t CO2 ha-2 yr-1 (vegetation dominated by heath). While accounting for the different global warming potential (GWP) of CO2, CH4 and N2O, the annual GHG balance was calculated. Emissions ranged between 25 and 53 t CO2-eq ha-1 yr-1 and were dominated by large emissions of CH4 (22-51 t CO2-eq ha-1 yr-1), with highest rates found at purple moor grass (Molinia caerulea) stands. These are to our knowledge the highest CH4 emissions so far reported for bog ecosystems in temperate Europe. As the restored area was subject to large fluctuations in the water table, we assume that the high CH4 emission rates were caused by a combination of both the temporal inundation of the easily decomposable plant litter of purple moor grass and the plant-mediated transport through its tissues. In addition, as a result of the land use history, mixed soil material due to peat extraction and refilling can serve as an explanation. With regards to the long time span passed since rewetting, we note that the initial increase in CH4 emissions due to rewetting as described in the literature is not inevitably limited to a short-term period.

  16. Calculations on the effect of pellet filling on the rewetting of overheated nuclear reactor fuel pins

    International Nuclear Information System (INIS)

    Pearson, K.G.; Loveless, J.

    1977-03-01

    Numerical solutions of the rewetting equations are presented which show the effect of filler material and gas gap on the rate of rewetting of an overheated fuel pin. It is shown that taking the presence of the fuel into account can lead to a large reduction in the calculated rewetting speed compared with a calculation which neglects the presence of fuel. The effect is most marked in conditions where rewetting speeds tend to be already low, such as at high pin temperatures and low ambient pressure. A comparison is made between the predictions of the present method and experimental data obtained on zircaloy and stainless steel pins filled with magnesia and with boron nitride. In all cases filling the pins produced a large reduction in rewetting speed and the agreement between the calculated and measured effect was encouraging. It is concluded that the presence of the UO 2 pellet filling should be taken into account when calculating rewetting speeds in safety assessments. (author)

  17. Annual greenhouse gas budget for a bog ecosystem undergoing restoration by rewetting

    Science.gov (United States)

    Lee, Sung-Ching; Christen, Andreas; Black, Andrew T.; Johnson, Mark S.; Jassal, Rachhpal S.; Ketler, Rick; Nesic, Zoran; Merkens, Markus

    2017-06-01

    Many peatlands have been drained and harvested for peat mining, agriculture, and other purposes, which has turned them from carbon (C) sinks into C emitters. Rewetting of disturbed peatlands facilitates their ecological recovery and may help them revert to carbon dioxide (CO2) sinks. However, rewetting may also cause substantial emissions of the more potent greenhouse gas (GHG) methane (CH4). Our knowledge of the exchange of CO2 and CH4 following rewetting during restoration of disturbed peatlands is currently limited. This study quantifies annual fluxes of CO2 and CH4 in a disturbed and rewetted area located in the Burns Bog Ecological Conservancy Area in Delta, BC, Canada. Burns Bog is recognized as the largest raised bog ecosystem on North America's west coast. Burns Bog was substantially reduced in size and degraded by peat mining and agriculture. Since 2005, the bog has been declared a conservancy area, with restoration efforts focusing on rewetting disturbed ecosystems to recover Sphagnum and suppress fires. Using the eddy covariance (EC) technique, we measured year-round (16 June 2015 to 15 June 2016) turbulent fluxes of CO2 and CH4 from a tower platform in an area rewetted for the last 8 years. The study area, dominated by sedges and Sphagnum, experienced a varying water table position that ranged between 7.7 (inundation) and -26.5 cm from the surface during the study year. The annual CO2 budget of the rewetted area was -179 ± 26.2 g CO2-C m-2 yr-1 (CO2 sink) and the annual CH4 budget was 17 ± 1.0 g CH4-C m-2 yr-1 (CH4 source). Gross ecosystem productivity (GEP) exceeded ecosystem respiration (Re) during summer months (June-August), causing a net CO2 uptake. In summer, high CH4 emissions (121 mg CH4-C m-2 day-1) were measured. In winter (December-February), while roughly equal magnitudes of GEP and Re made the study area CO2 neutral, very low CH4 emissions (9 mg CH4-C m-2 day-1) were observed. The key environmental factors controlling the seasonality of

  18. Rewetting phenomena and their relation to intermolecular forces between a hot wall and the fluid

    International Nuclear Information System (INIS)

    Gerweck, V.

    1989-12-01

    The rewetting phenomena and the different physical concepts which are used in their modelisation are reviewed. The present work studies the effect of the intermolecular forces between the hot wall and the fluid on this phase transition. Using suitable approximations, a local equation of state is obtained by the treatment of the fluid-fluid and fluid-wall intermolecular interactions. This local equation of state depends on the distance from the wall, and the critical pressure and temperature become a function of the distance from the wall, whereas the critical density is left constant throughout the fluid. At the wall, the critical pressure and temperature are half their bulk values and increase towards the bulk value as the distance from the wall increases. The penetration of a temperature profile in this fluid is studied by assuming that the liquid density is not strongly affected by this temperature profile as long as there is no phase transition. It is shown that the phase transition will occur extremely rapidly when the interfacial temperature upon contact is higher than the minimum of the local spinodal temperature, which varies with the distance from the wall. The result ist cast in the form of an interfacial rewetting temperature fT c above which rewetting of the surface by liquid-wall contacts is not expected because these contacts will be terminated in extremely short times. Comparing the theory with available data shows that in the usual rewetting situations the theory reduces to the use of the bulk spinodal temperature. For surfaces coated with poorly wetted materials the correction factor due to surface effects applies, reducing the rewetting temperature, in agreement with the experimental data. For liquid metals it appears that the theory is applied in a region where the basic theoretical approximations are very coarse; but even in that case the experimental trend is qualitatively predicted by the theory. (author) 43 figs., 11 tabs., 105 refs

  19. Dispersal timing and drought history influence the response of bacterioplankton to drying-rewetting stress.

    Science.gov (United States)

    Székely, Anna J; Langenheder, Silke

    2017-08-01

    The extent and frequency of drought episodes is expected to increase in the following decades making it a crucial stress factor for smaller water bodies. However, very little is known about how bacterioplankton is affected by increased evaporation and how these communities reassemble after rewetting. Here, we present results from a microcosm experiment that assessed the effect of drying-rewetting stress on bacterioplankton in the light of the stress history and the rate and timing of dispersal after the rewetting. We found that the drying phase resulted mainly in a change of function, whereas the complete desiccation and rewetting processes strongly affected both composition and function, which were, however, influenced by the initial conditions and stress history of the communities. Effects of dispersal were generally stronger when it occurred at an early stage after the rewetting. At this stage, selective establishment of dispersed bacteria coupled with enhanced compositional and functional recovery was found, whereas effects of dispersal were neutral, that is, predictable by dispersal rates, at later stages. Our studies therefore show that both the stress history and the timing of dispersal are important factors that influence the response of bacterial communities to environmental change and stress events.

  20. Experimental investigation of quench and re-wetting temperatures of hot horizontal tubes well above the limiting temperature for solid–liquid contact

    Energy Technology Data Exchange (ETDEWEB)

    Takrouri, Kifah, E-mail: takroukj@mcmaster.ca [Department of Engineering Physics, McMaster University, 1280 Main Street West, Hamilton, Ontario L8S 4L7 (Canada); Luxat, John, E-mail: luxatj@mcmaster.ca [Department of Engineering Physics, McMaster University, 1280 Main Street West, Hamilton, Ontario L8S 4L7 (Canada); Hamed, Mohamed [Thermal Processing Laboratory (TPL), Department of Mechanical Engineering, McMaster University, 1280 Main Street West, Hamilton, Ontario L8S 4L7 (Canada)

    2017-01-15

    Highlights: • Quench and re-wetting temperatures were measured upon jet quenching of hot cylindrical tubes. • Correlations have been developed and provided good fit of data. • Quench and re-wetting temperatures were found to greatly depend on water subcooling. • Stagnation point showed higher quench and re-wetting temperatures than other locations. • Quench temperature decreased by increasing surface curvature and tube conductivity. • Re-wetting temperature is a weak function of both variables. - Abstract: Quench cooling of a hot dry surface involves the rapid decrease in surface temperature resulting from bringing the hot surface into sudden contact with a coolant at a lower temperature. Quench temperature is the onset of the rapid decrease in surface temperature and corresponds to the onset of destabilization of a vapor film that exists between the hot surface and the coolant. Situations involving quench cooling are encountered in a number of postulated accidents in Canada Deuterium Uranium CANDU reactors, such as the quench of a hot calandria tube in certain Loss of Coolant Accidents LOCA. If the calandria tube temperature is not reduced by initiation of quench heat transfer, then this may lead to subsequent fuel channel failure and for this accident knowledge of quench heat transfer characteristics is of great importance. In this study, a Water Quench Facility WQF has been designed and built at the Thermal Processing Laboratory TPL at McMaster University and a series of experimental tests were carried out to investigate the quench of hot horizontal tubes using a vertical rectangular water multi-jet system. The tubes were heated to a temperature between 380 and 780 °C then cooled to the jet temperature. The temperature variation with time in tube circumferential and axial directions was measured. The two-phase flow behavior and the propagation of the re-wetting front around and along the tubes were simultaneously observed using a high-speed camera

  1. Revegetation dynamics after 15 years of rewetting in two extracted peatlands in Sweden

    Directory of Open Access Journals (Sweden)

    S.A. Kozlov

    2016-02-01

    Full Text Available The restoration of extracted peatlands poses challenges with regard to their recolonisation by vegetation. The most significant problems are unstable water levels, destroyed propagule bank, and temperature fluctuations on bare peat surfaces. Rewetting is considered necessary for the re-establishment of peat-forming vegetation. Revegetation was investigated in a long-term field study at two rewetted extracted peatland sites in south-central Sweden, namely Västkärr (originally a lagg fen and Porla (originally a bog. Both sites were expanses of bare peat before rewetting. Rewetting procedures were applied in 1999 and strongly promoted plant colonisation. At Västkärr, colonisation started in the first year after rewetting, mostly by species that were not found during repeat vegetation surveys 15 years later. By 2014, Västkärr was a shallow lake surrounded by mesotrophic and eutrophic vegetation with species such as Carex rostrata, Lemna minor, Typha latifolia, Phalaris arundinacea and Phragmites australis. Revegetation of the Porla site was slower and started with Eriophorum vaginatum and Polytrichum spp. Sphagnum mosses appeared after six years and had established quite well after 13 years. A residual Sphagnum peat layer, inflowing surface water and groundwater provided spatially variable nutrient conditions. Sphagnum species and E. vaginatum established in nutrient-poor areas, while C. rostrata, P. australis and Eriophorum angustifolium colonised more nutrient-rich locations.

  2. The effect of an exceptionally wet summer on methane effluxes from a 15-year re-wetted fen in north-east Germany

    Directory of Open Access Journals (Sweden)

    V. Huth

    2013-10-01

    Full Text Available Re-wetting minerotrophic fens has become an important strategy to mitigate climate change in Germany. However, recent studies report raised methane (CH4 effluxes during the first years after flooding. A minerotrophic fen in north-east Germany that was re-wetted 15 years ago was exposed to exceptionally heavy rainfall and freshwater flooding in August 2011. We measured CH4 effluxes from wetland vegetation stands dominated by Phragmites australis (Cav. Trin. ex Steud., Typha latifolia L. and Carex acutiformis Ehrh., using the closed-chamber method, fortnightly from March 2011 to March 2012 with extra sampling during the flooding. The respective annual effluxes of CH4 (mean ± 1 standard error from the three vegetation types were 18.5 ± 1.3, 21.1 ± 1.2 and 47.5 ± 5.0 g m-2 a-1, with the August effluxes contributing 40 %, 50 % and 10 % of the annual effluxes. Despite the freshwater flooding in August, annual CH4 effluxes from the 15-year re-wetted fen are similar to those reported from pristine fens. These results are promising because they indicate that, although CH4 effluxes are elevated after re-wetting, they may return to values typical for pristine fens after 15 years. Hence, re-wetting can achieve the purpose of reducing greenhouse gas effluxes from drained minerotrophic fens.

  3. Annual greenhouse gas budget for a bog ecosystem undergoing restoration by rewetting

    Directory of Open Access Journals (Sweden)

    S.-C. Lee

    2017-06-01

    Full Text Available Many peatlands have been drained and harvested for peat mining, agriculture, and other purposes, which has turned them from carbon (C sinks into C emitters. Rewetting of disturbed peatlands facilitates their ecological recovery and may help them revert to carbon dioxide (CO2 sinks. However, rewetting may also cause substantial emissions of the more potent greenhouse gas (GHG methane (CH4. Our knowledge of the exchange of CO2 and CH4 following rewetting during restoration of disturbed peatlands is currently limited. This study quantifies annual fluxes of CO2 and CH4 in a disturbed and rewetted area located in the Burns Bog Ecological Conservancy Area in Delta, BC, Canada. Burns Bog is recognized as the largest raised bog ecosystem on North America's west coast. Burns Bog was substantially reduced in size and degraded by peat mining and agriculture. Since 2005, the bog has been declared a conservancy area, with restoration efforts focusing on rewetting disturbed ecosystems to recover Sphagnum and suppress fires. Using the eddy covariance (EC technique, we measured year-round (16 June 2015 to 15 June 2016 turbulent fluxes of CO2 and CH4 from a tower platform in an area rewetted for the last 8 years. The study area, dominated by sedges and Sphagnum, experienced a varying water table position that ranged between 7.7 (inundation and −26.5 cm from the surface during the study year. The annual CO2 budget of the rewetted area was −179 ± 26.2 g CO2–C m−2 yr−1 (CO2 sink and the annual CH4 budget was 17 ± 1.0 g CH4–C m−2 yr−1 (CH4 source. Gross ecosystem productivity (GEP exceeded ecosystem respiration (Re during summer months (June–August, causing a net CO2 uptake. In summer, high CH4 emissions (121 mg CH4–C m−2 day−1 were measured. In winter (December–February, while roughly equal magnitudes of GEP and Re made the study area CO2 neutral, very low CH4 emissions (9 mg CH4–C m−2

  4. Investigation of the minimum film boiling temperature of water during rewetting under forced convective conditions

    International Nuclear Information System (INIS)

    Huang, X.C.; Bartsch, G.; Wang, B.X.

    1992-01-01

    The minimum film boiling temperature of water has been measured on a copper hollow cylinder of 50 mm length with the mass flux rate ranging from 25 to 500 kg/m 2 s and the pressure from 0.1 to 1.0 MPa at subcoolings of 5 to 50 K. Film boiling is established with help of a temperature-controlled system. Rewetting can be initiated by cutting off or very gradually reducing the power supply to the test section. A numerical method for solving the two-dimensional nonlinear inverse heat conduction problem is utilized in the data reduction, taking into account the axial heat conduction. The results are compared with the steady-state maximum transition boiling temperatures measured on the same test section and with the true quench temperatures available in the literature so far. (4 figures, 1 table) (Author)

  5. Carbon balance of rewetted and drained peat soils used for biomass production: A mesocosm study

    DEFF Research Database (Denmark)

    Karki, Sandhya; Elsgaard, Lars; Kandel, Tanka

    2016-01-01

    of lower CO2 emissions without losing agricultural land. The present study quantified the carbon balance (CO2, CH4 and harvested biomass C) of rewetted and drained peat soils under intensively managed reed canary grass (RCG) cultivation. Mesocosms were maintained at five different ground water levels (GWL......), i.e., 0, 10, 20 cm below the soil surface, representing rewetted peat soils, and 30 and 40 cm below the soil surface, representing drained peat soils. Net ecosystem exchange (NEE) of CO2 and CH4 emissions were measured during the growing period of RCG (May to September) using transparent and opaque...... closed chamber methods. The average dry biomass yield was significantly lower from rewetted peat soils (12 Mg ha−1) than drained peat soils (15 Mg ha−1). Also, CO2 fluxes of gross primary production (GPP) and ecosystem respiration (ER) from rewetted peat soils were significantly lower than drained peat...

  6. Bacterial community composition and extracellular enzyme activity in temperate streambed sediment during drying and rewetting.

    Directory of Open Access Journals (Sweden)

    Elisabeth Pohlon

    Full Text Available Droughts are among the most important disturbance events for stream ecosystems; they not only affect stream hydrology but also the stream biota. Although desiccation of streams is common in Mediterranean regions, phases of dryness in headwaters have been observed more often and for longer periods in extended temperate regions, including Central Europe, reflecting global climate change and enhanced water withdrawal. The effects of desiccation and rewetting on the bacterial community composition and extracellular enzyme activity, a key process in the carbon flow of streams and rivers, were investigated in a typical Central European stream, the Breitenbach (Hesse, Germany. Wet streambed sediment is an important habitat in streams. It was sampled and exposed in the laboratory to different drying scenarios (fast, intermediate, slow for 13 weeks, followed by rewetting of the sediment from the fast drying scenario via a sediment core perfusion technique for 2 weeks. Bacterial community structure was analyzed using CARD-FISH and TGGE, and extracellular enzyme activity was assessed using fluorogenic model substrates. During desiccation the bacterial community composition shifted toward composition in soil, exhibiting increasing proportions of Actinobacteria and Alphaproteobacteria and decreasing proportions of Bacteroidetes and Betaproteobacteria. Simultaneously the activities of extracellular enzymes decreased, most pronounced with aminopeptidases and less pronounced with enzymes involved in the degradation of polymeric carbohydrates. After rewetting, the general ecosystem functioning, with respect to extracellular enzyme activity, recovered after 10 to 14 days. However, the bacterial community composition had not yet achieved its original composition as in unaffected sediments within this time. Thus, whether the bacterial community eventually recovers completely after these events remains unknown. Perhaps this community undergoes permanent changes

  7. Contrasted response of colloidal, organic and inorganic dissolved phosphorus forms during rewetting of dried riparian soils

    Science.gov (United States)

    Gu, Sen; Gruau, Gérard; Malique, François; Dupas, Rémi; Gascuel-Odoux, Chantal; Petitjean, Patrice; Bouhnik-Le Coz, Martine

    2017-04-01

    Riparian vegetated buffer strip (RVBS) are currently used to protect surface waters from phosphorus (P) emissions because of their ability to retain P-enriched soil particles. However, this protection role may be counterbalanced by the development in these zones of conditions able to trigger the release of highly mobile dissolved or colloidal P forms. Rewetting after drying is one of these conditions. So far, the potential sources of P mobilized during rewetting after drying are not clearly identified, nor are clearly identified the chemical nature of the released dissolved P species, or the role of the soil P speciation on these forms. In this study, two riparian soils (G and K) showing contrasting soil P speciation (65% of inorganic P species in soil G, as against 70% of organic P) were submitted to three successive dry/wet cycles in the laboratory. Conventional colorimetric determination of P concentrations combined with ultrafiltration, and measurements of iron (Fe) and aluminum (Al) and dissolved organic carbon (DOC) contents using ICP-MS and TOC analyzers, respectively, were used to study the response of the different P forms to rewetting after drying and also their release kinetics during soil leaching. For both soils, marked P release peaks were observed at the beginning of each wet cycles, with the organic-rich K soils giving, however, larger peaks than the inorganic one (G soil). For both soils also, concentrations in molybdate reactive P (MRP) remained quite constant throughout each leaching episode, contrary to the molybdate unreactive P (MUP) concentrations which were high immediately after rewetting and then decreased rapidly during leaching. A speciation change was observed from the beginning to the end of all leaching cycles. Colloidal P was found to be a major fraction of the total P immediately after rewetting (up to 50-70%) and then decreased to the end of each wet cycle where most of the eluted P was true dissolved inorganic P. Colloidal

  8. Partial drying accelerates bacterial growth recovery to rewetting

    DEFF Research Database (Denmark)

    Meisner, Annelein; Leizeaga, Ainara; Rousk, Johannes

    2017-01-01

    , bacterial growth rates increase immediately in a linear fashion. In the Type 2 pattern, bacterial growth rates increase exponentially after a lag period. However, soils are often only partially dried. Partial drying (higher remaining moisture content before rewetting) may be considered a less harsh...

  9. Investigating the legacy effect of drought on microbial responses to drying and rewetting along a Texan precipitation gradient

    Science.gov (United States)

    Hicks, Lettice; Leizeaga, Ainara; Hawkes, Christine; Rousk, Johannes

    2017-04-01

    Hydrological regimes will intensify due to climate change, thus increasing the duration and intensity of drought and rainfall events. Rewetting of dry soil is known to stimulate dramatic CO2 releases. A clear understanding of the mechanisms that determine the dynamics of CO2 loss upon rewetting is therefore required to characterise ecosystem C-budgets and predict responses to climate change. Laboratory studies have identified two distinct responses upon rewetting; bacterial growth either increases linearly immediately, with maximal respiration also occurring immediately and decreasing exponentially with time ("Type 1"), or bacterial growth increases exponentially after a period of near-zero growth, with a sustained period of elevated respiration, sometimes followed by a secondary increase in respiration coinciding with the onset of bacterial growth ("Type 2"). A shift from a Type 1 to a Type 2 response has been observed with increasing duration and intensity of drying prior to rewetting. The size of the surviving microbial community after drying, relative to resources available after rewetting, is suggested to dictate whether a Type 1 or 2 response occurs, with more 'harsh' (i.e. longer or more severe) drying reducing microbial biomass such that carbon available upon rewetting is sufficient to support exponential growth (leading to Type 2 response). However, this is yet to be tested in intact ecosystems. We investigated the legacy of drought on microbial responses to drying and rewetting using grassland soils from a natural precipitation gradient in Texas. Mean annual precipitation spanned a 500 mm range (400-900 mm year-1) across the 400 km gradient, while mean annual temperature was constant. Soil properties (pH, SOM) did not vary systematically across the gradient, with differences reflecting land-use history rather than rainfall. Air dried soils from 18 sites were rewetted to 50 % water holding capacity with bacterial growth, fungal growth and respiration

  10. Effect of heat transfer in the fog region during core reflooding

    International Nuclear Information System (INIS)

    Rouai, N. M.; El-sawy, H. M.

    1993-01-01

    Core reflooding following a loss of coolant accident (LOCA) in a pressurized water reactor (PWR) received considerable attention during the past thirty years. In this paper a one dimensional model is used to study the effect of the heat transfer in the fog region ahead of the wet front reflooding rate of a cylindrical fuel element following a LOCA in a PWR. The heat conduction equation in the cladding is solved in coordinate system moving with the wet front under a variety of condition to investigate the effects of such parameters as the initial cladding surface temperature, the decay heat generation rate in the fuel and the mode of heat transfer prevailing. The cladding surface is divided into three axial regions according to the mechanism of heat transfer, namely, a boiling region behind the wet front, a fog region ahead of the wet front and a dry region further downstream of the wet front. The effect of changing the heat transfer coefficient in the fog region on the rewetting rate and on the fog length is investigated. The results of this simple model show that increasing the heat transfer in the fog region increases the rewetting velocity and consequently decreases the fog length. The results are in general agreement with a more accurate two-dimensional model and experimental data. (author)

  11. Installation for rewetting experiments

    International Nuclear Information System (INIS)

    Rezende, H.C.; Ladeira, L.C.D.

    1986-03-01

    A test facility for rewetting experiments (ITR), has been erected at the Thermalhydraulics Laboratory of Centro de Desenvolvimento da Tecnologia Nuclear (CDTN), with the objective of performing investigation of basic phenomena that occur during the reflood phase of a Loss of Coolant Accident (LOCA), in a Pressurized Water Reactor (PWR), utilizing tubular and annular test sections. The mechanical aspects of the facility, its power supply system and its instrumentation are described. The results of the calibration of the instruments and the description of two typical testes performed to verify the operational conditions are presented. A comparison with calculations using a computer code is also presented. (Author) [pt

  12. Design of Spillway Structures of Peatland Rewetting systems

    Directory of Open Access Journals (Sweden)

    Sainov Mihail Petrovich

    2014-03-01

    Full Text Available In summer 2010 drought and heat weather cause numerous peat fires. During two months Moscow was shrouded in acid smoke. To prevent such situations government of Moscow region decided to rewet previously drained peatlands. Peatland rewetting systems can be divided into two types. The first type is watering system based on previously used drainage system. The main idea of this method is rising of groundwater levels with the help of special water retaining constructions installed in drainage canals. The design of water receivers allows keeping up water level in canals and draining excesses. There are two types of water receivers: dock-type water receiver and water receiver as a portal to the gate. The choice of one or another type of water receiver depends on the canal depth. If it is less than 1.5 m, we apply portal construction. At the depth of more than 1.5 m the mine water receiver is more suitable. The second way of watering previously drained peatlands is the creation of ponds, dams on streams and small rivers. Special discharge structures increase water level in the river upstream. In downstream water level rises due to the redistribution of the flow. As a result, the groundwater level rises and peat become watered. There are two types of spillway structures: with direct overflow wall and labyrinth overflow wall. Structure with direct overflow wall is applicable on small rivers. In narrow alignments with high consumptions it is better to use another type of weir. As output it is necessary to notice that all constructions used in peatlands watering were designed as simple and reliable as possible. It is so because unpredictable weather conditions can cause beyond the design flows so weirs must have necessary reserve of passing costs.

  13. Reflooding phase of the LOCA - state of the art II. Rewetting and liquid entrainment

    International Nuclear Information System (INIS)

    Elias, E.; Yadigaroglu, G.

    1977-01-01

    Understanding the mechanisms by which hot fuel rods quench and the physics of liquid droplet entrainment is important for the analysis of the reflooding phase of the LOCA. Published models of the rewetting process include simple one-dimensional solutions. The basic physical assumptions of these models and the numerical values assigned to the various parameters, as well as empirical rewetting correlations are discussed. The various mechanisms for liquid droplet entrainment and analytical formulations of the critical gas velocity and of the droplet diameter at the onset of entrainment are reviewed

  14. Nitrogen supply modulates the effect of changes in drying-rewetting frequency on soil C and N cycling and greenhouse gas exchange.

    Science.gov (United States)

    Morillas, Lourdes; Durán, Jorge; Rodríguez, Alexandra; Roales, Javier; Gallardo, Antonio; Lovett, Gary M; Groffman, Peter M

    2015-10-01

    Climate change and atmospheric nitrogen (N) deposition are two of the most important global change drivers. However, the interactions of these drivers have not been well studied. We aimed to assess how the combined effect of soil N additions and more frequent soil drying-rewetting events affects carbon (C) and N cycling, soil:atmosphere greenhouse gas (GHG) exchange, and functional microbial diversity. We manipulated the frequency of soil drying-rewetting events in soils from ambient and N-treated plots in a temperate forest and calculated the Orwin & Wardle Resistance index to compare the response of the different treatments. Increases in drying-rewetting cycles led to reductions in soil NO3- levels, potential net nitrification rate, and soil : atmosphere GHG exchange, and increases in NH4+ and total soil inorganic N levels. N-treated soils were more resistant to changes in the frequency of drying-rewetting cycles, and this resistance was stronger for C- than for N-related variables. Both the long-term N addition and the drying-rewetting treatment altered the functionality of the soil microbial population and its functional diversity. Our results suggest that increasing the frequency of drying-rewetting cycles can affect the ability of soil to cycle C and N and soil : atmosphere GHG exchange and that the response to this increase is modulated by soil N enrichment. © 2015 John Wiley & Sons Ltd.

  15. Analysis of Tank PMD Rewetting Following Thrust Resettling

    Science.gov (United States)

    Weislogel, M. M.; Sala, M. A.; Collicott, S. H.; Rame, Enrique (Technical Monitor)

    2002-01-01

    Recent investigations have successfully demonstrated closed-form analytical solutions of spontaneous capillary flows in idealized cylindrical containers with interior corners. In this report, the theory is extended and applied to complex containers modeling spacecraft fuel tanks employing propellant management devices (PMDs). The specific problem investigated is one of spontaneous rewetting of a typical partially filled liquid fuel/cryogen tank with PMD after thrust resettling. The transients of this flow impact the logistics of orbital maneuvers and potentially tank thermal control. The general procedure to compute the initial condition (mean radius of curvature for the interface) for the closed-form transient flows is first outlined then solved for several 'complex' cylindrical tanks exhibiting symmetry. The utility and limitations of the technique as a design tool are discussed in a summary, which also highlights comparisons with NASA flight data of a model propellant tank with PMD.

  16. Turn on, fade out - methane exchange in a coastal fen over a period of six years after rewetting

    Science.gov (United States)

    Jurasinski, Gerald; Glatzel, Stephan; Hahn, Juliane; Koch, Stefan; Koch, Marian; Koebsch, Franziska

    2016-04-01

    The rewetting of drained peatlands is widely regarded as an adequate measure for the mitigation of greenhouse gas emissions. Therefore, especially in NE Germany, many peatlands are being rewetted. Our knowledge about greenhouse gas exchange associated with rewetting is mainly based on short-term experiments or space-for-time substitutions. These approaches do not consider the transient character of ecosystem acclimatization to flooding by rewetting. Moreover data in this regard on coastal peatland ecosystems are sparse. Here, we present 7 years of data on CH4-exchange in a coastal fen after rewetting by flooding. On the site „Rodewiese", which is located within the NSG "Hütelmoor und Heiligensee" in the Northeast of Rostock, NE Germany, we have established a long term research observatory addressing atmospheric C-exchange. The site is part of the TERENO network. Since summer 2009 we determine CH4 fluxes with closed chambers distributed widely across the study site and CO2-exchange with eddy covariance as well as ancillary data on vegetation, hydrology, and biogeochemistry. This talk addresses the CH4-exchange over time whereas CO2-exchange data are presented by Koebsch et al. in the same session. Rewetting turned the site from a summer dry fen with mean annual water levels of around -0.08m into a shallow lake with water levels up to 0.60m. In the first year after flooding, we observed a substantial die-back of vegetation, especially in stands of Carex acutiformis. Flooding increased methane release rates to extremely high levels of up to 4.3 t ha-1 a-1 for sedge stands and 2.7 t ha-1 a-1 on average, which amounts to 75.6 t ha-1 a-1 in CO2-equivalents. Thereafter, the averaged annual CH4 emissions decreased asymptotically and where at an average of 0.5 t ha-1 a-1 (14 t ha-1 a-1 in CO2-equivalents) in 2015. Factoring in the NEE of the growing season (from Eddy measurements) suggests that the system may be slightly above neutral with respect to the greenhouse

  17. Biomassa microbiana em amostras de solos secadas ao ar e reumedecidas Microbial biomass in air dried and rewetted soil samples

    Directory of Open Access Journals (Sweden)

    Antônio Samarão Gonçalves

    2002-05-01

    Full Text Available O objetivo do trabalho foi avaliar a viabilidade do condicionamento de amostras como terra fina secada ao ar (TFSA por curto período, para a determinação do carbono da biomassa microbiana (BMS-C, pelo método da fumigaçãoextração, e verificar a respiração microbiana basal (RB do solo. O condicionamento como TFSA, procedendo-se à fumigação para a análise da BMS-C imediatamente ou 24 horas após o reumedecimento, proporcionou valores de BMS-C para os solos Podzólicos, Latossolo Vermelho-Amarelo álico e Orgânico, semelhantes aos valores dos seus controles. Os solos Glei Pouco Húmico e Vertissolo apresentaram valores de BMS-C similares aos do controle a partir de 24 horas de incubação; o solo Planossolo arenoso apresentou valores similares aos do controle com 72 horas, e a Rendizina, com 168 horas de incubação. Na maioria dos solos, a RB determinada na TFSA apresentou valores maiores do que os do tratamento-controle, quando avaliada imediatamente ou 24 horas após o reumedecimento a 60% da capacidade máxima de retenção de água, seguida de queda e manutenção em níveis semelhantes ao do controle nos períodos subseqüentes. O précondicionamento, de curta duração, como TFSA, é promissor para a determinação da BMS-C, quando níveis e períodos adequados de reumedecimento são adotados.The objective of this work was to evaluate the utilization of short term air dried soil samples in a determination of soil microbial biomass (SMB-C, by a fumigationextraction method, and soil microbial basal respiration (BR. Zero time or 24 hours rewetting incubation period before fumigation procedure gave values of SMB-C similar to those of the control for the Podzolic soils, Allic RedYellow Latosol and Organic soil. Low Humic Gley and Vertisol soils gave values of SMB-C similar to those of the control for periods of incubation equal or higher than 24 hours. Planosol (sandy soil and Rendzina soils gave values of SMB-C similar to the

  18. Rewetted industrial cutaway peatlands in western Ireland: a prime location for climate change mitigation?

    Directory of Open Access Journals (Sweden)

    D. Wilson

    2013-04-01

    Full Text Available Rewetting of drained industrial peatlands may reduce greenhouse gas (GHG emissions and promote recolonisation by peat forming plant species. We investigated carbon dioxide (CO2, methane (CH4 and nitrous oxide (N2O dynamics over a three-year period in a rewetted industrial peatland in Ireland. Sample plots were established in bare peat, Juncus effusus-Sphagnum cuspidatum, Sphagnum cuspidatum and Eriophorum angustifolium dominated microsites. The relationships between fluxes and environmental variables were examined and regression models were used to provide an estimate of the annual GHG balance for each microsite. All the vegetated microsites were carbon sinks for the duration of the study. Highest uptake occurred in the Eriophorum microsite (146–583 g C m-2 yr-1, followed by Juncus-Sphagnum (35–204 g C m-2 yr-1 and Sphagnum (5–140 g C m-2 yr-1. The bare peat microsite was a source of 37–82 g C m-2 yr-1. No N2O fluxes were detected. Strong inter-annual variation was observed in all microsites, driven by variation in precipitation and subsequent changes in the position of the water table. In terms of Global Warming Potential (GWP, the microsites had either a cooling effect (Eriophorum, a close to neutral effect (Juncus-Sphagnum, Sphagnum or a warming effect (bare peat on the climate.

  19. Drained peatlands used for extraction and agriculture: biogeochemical status with special attention to greenhouse gas fluxes and rewetting

    Science.gov (United States)

    Sirin, Andrey; Chistotin, Maxim; Suvorov, Gennady; Glagolev, Mikhail; Kravchenko, Irina; Minaeva, Tatiana

    2010-05-01

    ditches. The findings were supported by the studies conducted from 2005 at drained peatland sites in Moscow region (European part of Russia) which are used for peat extraction or as hayfield (Chistotin et al., 2006). Unexpected transient methane fluxes were observed at the inter-ditch surfaces in two types of sites: milled peat extraction area and used as a hay field after partial peat extraction. Under warm and wet conditions methane was released even from peat stockpiles. Microbiological studies showed not lower and near to twice higher genomic diversity of methanogens in extracted sites and in a hayfield as compared to virgin mire. We suppose that well-developed plant roots at the grassland provide a source of fresh organic material used for CH4 production. To test this hypothesis, a pot experiment with mesocosms which model three succession stages (bare peat, grass sowing, and developed grassland) under permanently high or fluctuating wetness was conducted. Methane efflux from peat under developed grassland was higher as compared to the other treatments. Under permanently high water supply the methane emission was 1 to 2 orders of magnitude higher. The obtained results clearly showed that plant organic matter can be an additional source of methane after rewetting which is obviously needed for abandoned peatland sites not used for agriculture any more. To mitigate the emissions, such management options as removal of the surface peat layer before rewetting could be applied. This practice could have additional benefits achieved by bringing day surface closer to ground water table level and forming more favorable soil conditions for mire species.

  20. A Global Database of Gas Fluxes from Soils after Rewetting or Thawing, Version 1.0

    Data.gov (United States)

    National Aeronautics and Space Administration — This database contains information compiled from published studies on gas flux from soil following rewetting or thawing. The resulting database includes 222 field...

  1. An experimental study of the effect of external thermocouples on rewetting during reflood

    International Nuclear Information System (INIS)

    Shires, G.L.; Butcher, A.A.; Carpenter, B.G.; McCune, D.S.; Pearson, K.G.

    1980-04-01

    The validation of computer codes used for PWR safety assessment often depends upon experiments carried out with either real fuel pins or electrically heated fuel pin simulators. In some cases, and this applies particularly to in-pile tests, temperatures are measured by means of sheathed thermocouples attached externally to the pins and this raises the question of the possible effect of such thermocouples on the two phase hydraulics and heat transfer which are being studied. This paper describes the experiments which subjected two realistic fuel pin simulators, one with and one without external thermocouples, to identical bottom flooding conditions. They demonstrate very clearly that external thermocouples act as preferential rewetting sites and thereby increase the rate of propagation of the quench front. In the view of the authors of this paper the facts described raise serious doubts about the validity of rewetting data obtained from experiments employing external thermocouples. (U.K.)

  2. Polyphenols as enzyme inhibitors in different degraded peat soils: Implication for microbial metabolism in rewetted peatlands

    Science.gov (United States)

    Zak, Dominik; Roth, Cyril; Gelbrecht, Jörg; Fenner, Nathalie; Reuter, Hendrik

    2015-04-01

    Recently, more than 30,000 ha of drained minerotrophic peatlands (= fens) in NE Germany were rewetted to restore their ecological functions. Due to an extended drainage history, a re-establishment of their original state is not expected in the short-term. Elevated concentrations of dissolved organic carbon, ammonium and phosphate have been measured in the soil porewater of the upper degraded peat layers of rewetted fens at levels of one to three orders higher than the values in pristine systems; an indicator of increased microbial activity in the upper degraded soil layers. On the other hand there is evidence that the substrate availability within the degraded peat layer is lowered since the organic matter has formerly been subject to intense decomposition over the decades of drainage and intense agricultural use of the areas. Previously however, it was suggested that inhibition of hydrolytic enzymes by polyphenolic substances is suspended during aeration of peat soils mainly due to the decomposition of the inhibiting polyphenols by oxidising enzymes such as phenol oxidase. Accordingly we hypothesised a lack of enzyme inhibiting polyphenols in degraded peat soils of rewetted fens compared to less decomposed peat of more natural fens. We collected both peat samples at the soil surface (0-20 cm) and fresh roots of dominating vascular plants and mosses (as peat parent material) from five formerly drained rewetted sites and five more natural sites of NE Germany and NW Poland. Less decomposed peat and living roots were used to obtain an internal standard for polyphenol analysis and to run enzyme inhibition tests. For all samples we determined the total phenolic contents and in addition we distinguished between the contents of hydrolysable and condensed tannic substances. From a methodical perspective the advantage of internal standards compared to the commercially available standards cyanidin chloride and tannic acid became apparent. Quantification with cyanidin or

  3. Effects of rewetting on greenhouse gas emissions in different microtopes in a cut-over drained bog in Schleswig-Holstein, Germany

    Science.gov (United States)

    Vybornova, Olga; Pfeiffer, Eva-Maria; Kutzbach, Lars

    2016-04-01

    In peatlands, all biogeochemical processes and the amount of exported carbon and nitrogen compounds are strongly influenced by changes in the water table. Peatland drainage leads to increased peat oxidization and changes peatlands from carbon sinks to net carbon sources. Especially, the emissions of the important greenhouse gases (GHG) carbon dioxide, methane and nitrous oxide are increased due to drainage. The currently ongoing restoration in the bog Himmelmoor (N 53° 44'20", E 9° 51'00", Quickborn) with an extent of about 6 km2 one of the largest raised bogs in Schleswig-Holstein, offers the possibility to characterize and to document the development of the fluxes at different sites before, during and after rewetting, using a method of small-scale closed chambers. Six subsites with differing water level and land use were identified: an area that was rewetted 30 years ago with Sphagnum vegetation, an area rewetted in 2009, an area with on-going peat extraction, deep peat cutting ditches refilled with peat with and without Eriophorum angustifolium vegetation and a comparatively dry peat dam. We determined that in the course of years 2014-2015 the measured N2O and CO2 fluxes varied between -0,1 and 1,9 mg m-2 h-1 and between -0,12 and 1,09 g m-2 h-1, respectively, and the highest nitrous oxide as well as carbon dioxide fluxes are typical for the dry peat dam study site. The measured CH4 fluxes were between -1,8 and 22,7 mg m-2 h-1, where the highest rates were found on the area rewetted 30 years ago and on the peat cutting ditches with Eriophorum angustifolium. Accounting for the different global warming potentials (GWP) of the measured greenhouse gases, the annual GHG balance was calculated. Emissions from all study sites ranged between 5,2 and 36 t CO2-eq ha-1 year-1 and were dominated by high emissions of CO2 (2,5 up to 25,5 t CO2-eq ha-1 year-1). Highest emission rates were found at the dry peat dam site and at the area rewetted 30 years ago. The peat dams and

  4. Long-term grassland management effects on soil Phosphorus status on rewetted Histosols

    Science.gov (United States)

    Heller, Sebastian; Müller, Jürgen; Kayser, Manfred

    2017-04-01

    Since the Neolithic Period, the cultivation of wetlands has played a significant role for the settlement of Humans northwest Germany. A continuing drainage of the wetlands over the centuries and an intensified soil cultivation during the last decades has caused irreversible peat degradation and led to fundamental changes in the landscape. Nowadays, almost 70 % of the 4345 km2 peatland of Lower Saxony is altered by agriculture. For the revitalization of wetland ecosystems, permanent rewetting is an integral component to preserve the functions of organic soils and achieve resilient, speciesrich wetlands. However, permanent rewetting measures are not always feasible. In our study area at the Osterfeiner Moor, a fen located in the Dümmer lowlands near Osnabrück, intensive forage cropping areas were converted into extensive permanent grasslands accompanied by temporary rewetting during winter. This management practice combined with zero fertilization and a low mowing and grazing intensity aims at mitigating mineralisation of peat layers and creating a habitat for endangered meadow bird species. In this semi-natural ecosystem soil phosphorus (P) dynamics play a crucial role. However, longterm research results on P availability of degraded and rewetted fens are still lacking. Thus, we investigated the interaction of different grassland uses and P dynamics in the soil. We described P depletion of the topsoil over a time scale of 17 years after the implementation of restoration measures. Our study site comprises of 180 ha protected grassland divided into 52 management plots. According to the management system, we divided the plots into meadows, pastures and combinations of cutting and grazing. The soils in our study area can be characterised as drained organic soils, WRB: Rheic Sapric Histosols (Drainic), with drastic degradation properties through moorsh forming processes. Plant-available P (double lactate extraction method: PDL) was analysed from representative topsoil

  5. Towards large-scale paludiculture: addressing the challenges of biomass harvesting in wet and rewetted peatlands

    Directory of Open Access Journals (Sweden)

    C. Schröder

    2015-12-01

    Full Text Available Peatland drainage causes peat degradation, which results in high greenhouse gas emissions and ongoing subsidence of the ground surface. To avoid further land degradation, the rewetting of peatlands is essential. The new land use concept of paludiculture - the use of wet and rewetted peatlands for agriculture and forestry - now offers possibilities for landowners and land managers to continue using these sites under wet conditions. But new challenges arise due to the limited bearing capacity of wet soils, which restricts accessibility for machinery. Whilst many site-specific technical solutions for harvesting on wet peatland are available, it remains unclear whether current machinery is suitable for use in the large-scale implementation of paludiculture. Repeated crossings of the same ground can easily disturb the upper peat layer and cause serious problems for the removal of biomass. In this article we present available machinery and approaches to biomass harvesting; and explore how the number of transport runs required for biomass removal varies with productivity of the site, cargo capacity and working width of the harvesting machinery. The results are used in a discussion of logistics and infrastructure requirements to facilitate the implementation of paludiculture. Whilst there is still considerable scope for improvement of harvesting technologies, our results show that a peat-conserving harvest from wet and rewetted peatlands is possible with adjustments to harvesting technique, logistics and site infrastructure.

  6. Rate of Decomposition of Organic Matter in Soil as Influenced by Repeated Air Drying-Rewetting and Repeated Additions of Organic Material

    DEFF Research Database (Denmark)

    Sørensen, Lasse Holst

    1974-01-01

    Repeated air drying and rewetting of three soils followed by incubation at 20°C resulted in an increase in the rate of decomposition of a fraction of 14C labeled organic matter in the soils. The labeled organic matter originated from labeled glucose, cellulose and straw, respectively, metabolized...... of the treatment was least in the soil which had been incubated with the labeled material for the longest time. Additions of unlabeled, decomposable organic material also increased the rate of decomposition of the labeled organic matter. The evolution of labeled CO2 during the 1st month of incubation after...... addition was in some cases 4–10 times larger than the evolution from the controls. During the continued incubation the evolution decreased almost to the level of the controls, indicating that the effect was related to the increased biological activity in the soils during decomposition of the added material...

  7. Complete annual CO2, CH4, and N2O balance of a temperate riparian wetland 12 years after rewetting

    DEFF Research Database (Denmark)

    Kandel, Tanka; Lærke, Poul Erik; Hoffmann, Carl Christian

    2018-01-01

    Drained riparian wetlands have been rewetted and restored in recent decades to remove nutrients, increase biodiversity, and mitigate soil carbon dioxide (CO2) emissions. Yet, few studies have documented the long-term effects of rewetting on complete greenhouse gas (GHG) balances including emissio...

  8. Current status of the post boiling transition research in Japan. Integrity evaluation of nuclear fuel assemblies after boiling transition and development of rewetting correlations

    International Nuclear Information System (INIS)

    Hara, Takashi; Mizokami, Shinya; Kudo, Yoshiro; Komura, Seiichi; Nagata, Yoshifumi; Morooka, Shinichi

    2003-01-01

    Development of rewetting correlation formula was the key to predict fuel-cladding temperature after Boiling Transition (BT). Japanese BWR utilities and vendors performed some tests of rewetting and made two rewetting correlation formulas. The effect on fuel integrity after BT depends on temperature of fuel rod and time of dryout. Main cause of losing fuel integrity during BWR's Anticipated Operational Occurrences (AOO) after BT is embrittlement of the claddings due to oxidation. Ballooning of fuel rod is excepted because its pressure boundary isn't broken. In Japan, the Standards Committee of Atomic Energy Society of Japan (AESJ) is making post BT standard. This standard provides guidelines based on the latest knowledge to judge fuel integrity in case of BT and the validity of reusing the fuel assembly that experienced BT in BWRs. (author)

  9. Splines employment for inverse problem of nonstationary thermal conduction

    International Nuclear Information System (INIS)

    Nikonov, S.P.; Spolitak, S.I.

    1985-01-01

    An analytical solution has been obtained for an inverse problem of nonstationary thermal conduction which is faced in nonstationary heat transfer data processing when the rewetting in channels with uniform annular fuel element imitators is investigated. In solving the problem both boundary conditions and power density within the imitator are regularized via cubic splines constructed with the use of Reinsch algorithm. The solution can be applied for calculation of temperature distribution in the imitator and the heat flux in two-dimensional approximation (r-z geometry) under the condition that the rewetting front velocity is known, and in one-dimensional r-approximation in cases with negligible axial transport or when there is a lack of data about the temperature disturbance source velocity along the channel

  10. Conversion of a moderately rewetted fen to a shallow lake - implications for net CO2 exchange

    Science.gov (United States)

    Koebsch, Franziska; Glatzel, Stephan; Hofmann, Joachim; Forbrich, Inke; Jurasinski, Gerald

    2013-04-01

    Extensive rewetting projects to re-establish the natural carbon (C) sequestration function of degraded peatlands are currently taking place in Europe and North-America. Year-round flooding provides a robust measure to prevent periods of drought that are associated with ongoing peat mineralization and to initiate the accumulation of new organic matter. Here, we present measurements of net carbon dioxide (CO2) exchange during the gradual conversion of a moderately rewetted fen to a shallow lake. When we started our measurements in 2009, mean growing season water level (MWGL) was 0 cm. In 2010 the site was flooded throughout the year with MWGL of 36 cm. Extraordinary strong rainfalls in July 2011 resulted in a further increase of MWGL to 56 cm. Measurements of net ecosystem exchange (NEE) were conducted during growing seasons (May-October) using the Eddy Covariance method. Information about vegetation vitality was deduced from the enhanced vegetation index (EVI) based on MODIS data. Ecosystem respiration (Reco) and gross ecosystem production (GEP) were high during vegetation period 2009 (1273.4 and -1572.1 g CO2-C m-2), but decreased by 61 and 46% respectively when the fen was flooded throughout 2010. Under water-logged conditions, heterotrophic respiration declines and gas exchange is limited. Moreover, flooding is a severe stress factor for plants and decreases autotrophic respiration and photosynthesis. However, in comparison to 2010, rates of Reco and GEP doubled during the beginning of growing season 2011, indicating plastic response strategies of wetland plants to flooding. Presumably, plants were not able to cope with the further increase of water levels to up to 120 cm in June/July 2011, resulting in another drop of GEP and Reco. The effects of plant vitality on GEP were confirmed by the remote sensed vegetation index. Throughout all three growing seasons, the fen was a distinct net CO2 sink (2009: -333.3±12.3, 2010: -294.1±8.4, -352.4±5.1 g CO2-C m-2

  11. Effect of reed canary grass cultivation on greenhouse gas emission from peat soil at controlled rewetting

    DEFF Research Database (Denmark)

    Karki, Sandhya; Elsgaard, Lars; Lærke, Poul Erik

    2015-01-01

    Cultivation of bioenergy crops in rewetted peatland (paludiculture) is considered as a possible land use option to mitigate greenhouse gas (GHG) emissions. However, bioenergy crops like reed canary grass (RCG) can have a complex influence on GHG fluxes. Here we determined the effect of RCG...... and bare soil were measured at weekly to fortnightly intervals with static chamber techniques for a period of 1 year. Cultivation of RCG increased both ER and CH4 emissions, but decreased the N2O emissions. The presence of RCG gave rise to 69, 75 and 85% of total ER at −20, −10 and 0 cm GWL, respectively...... from ER were obviously the dominant RCG-derived GHG flux, but above-ground biomass yields, and preliminary measurements of gross photosynthetic production, showed that ER could be more than balanced due to the photosynthetic uptake of CO2 by RCG. Our results support that RCG cultivation could be a good...

  12. High soil solution carbon and nitrogen concentrations in a drained Atlantic bog are reduced to natural levels by 10 years of rewetting

    Science.gov (United States)

    Frank, S.; Tiemeyer, B.; Gelbrecht, J.; Freibauer, A.

    2014-04-01

    Anthropogenic drainage of peatlands releases additional greenhouse gases to the atmosphere, and dissolved carbon (C) and nutrients to downstream ecosystems. Rewetting drained peatlands offers a possibility to reduce nitrogen (N) and C losses. In this study, we investigate the impact of drainage and rewetting on the cycling of dissolved C and N as well as on dissolved gases, over a period of 1 year and a period of 4 months. We chose four sites within one Atlantic bog complex: a near-natural site, two drained grasslands with different mean groundwater levels and a former peat cutting area rewetted 10 years ago. Our results clearly indicate that long-term drainage has increased the concentrations of dissolved organic carbon (DOC), ammonium, nitrate and dissolved organic nitrogen (DON) compared to the near-natural site. DON and ammonium contributed the most to the total dissolved nitrogen. Nitrate concentrations below the mean groundwater table were negligible. The concentrations of DOC and N species increased with drainage depth. In the deeply-drained grassland, with a mean annual water table of 45 cm below surface, DOC concentrations were twice as high as in the partially rewetted grassland with a mean annual water table of 28 cm below surface. The deeply drained grassland had some of the highest-ever observed DOC concentrations of 195.8 ± 77.3 mg L-1 with maximum values of >400 mg L-1. In general, dissolved organic matter (DOM) at the drained sites was enriched in aromatic moieties and showed a higher degradation status (lower DOC to DON ratio) compared to the near-natural site. At the drained sites, the C to N ratios of the uppermost peat layer were the same as of DOM in the peat profile. This suggests that the uppermost degraded peat layer is the main source of DOM. Nearly constant DOM quality through the profile furthermore indicated that DOM moving downwards through the drained sites remained largely biogeochemically unchanged. Unlike DOM concentration, DOM

  13. CO2 response to rewetting of hydrophobic soils - Can soil water repellency inhibit the 'Birch effect'?

    Science.gov (United States)

    Sanchez-Garcia, Carmen; Urbanek, Emilia; Doerr, Stefan

    2017-04-01

    Rewetting of dry soils is known to cause a short-term CO2 pulse commonly known as the 'Birch effect'. The displacement of CO2 with water during the process of wetting has been recognised as one of the sources of this pulse. The 'Birch effect' has been extensively observed in many soils, but some studies report a lack of such phenomenon, suggesting soil water repellency (SWR) as a potential cause. Water infiltration in water repellent soils can be severely restricted, causing overland flow or increased preferential flow, resulting in only a small proportion of soil pores being filled with water and therefore small gas-water replacement during wetting. Despite the suggestions of a different response of CO2 fluxes to wetting under hydrophobic conditions, this theory has never been tested. The aim of this study is to test the hypothesis that CO2 pulse does not occur during rewetting of water repellent soils. Dry homogeneous soils at water-repellent and wettable status have been rewetted with different amounts of water. CO2 flux as a response to wetting has been continuously measured with the CO2 flux analyser. Delays in infiltration and non-uniform heterogeneous water flow were observed in water repellent soils, causing an altered response in the CO2 pulse in comparison to typically observed 'Birch effect' in wettable systems. The main conclusion from the study is that water repellency not only affects water relations in soil, but has also an impact on greenhouse gas production and transport and therefore should be included as an important parameter during the sites monitoring and modelling of gas fluxes.

  14. Mitochondrial DNA control region analysis of three ethnic groups in the Republic of Macedonia

    Science.gov (United States)

    Jankova-Ajanovska, Renata; Zimmermann, Bettina; Huber, Gabriela; Röck, Alexander W.; Bodner, Martin; Jakovski, Zlatko; Janeska, Biljana; Duma, Aleksej; Parson, Walther

    2014-01-01

    A total of 444 individuals representing three ethnic groups (Albanians, Turks and Romanies) in the Republic of Macedonia were sequenced in the mitochondrial control region. The mtDNA haplogroup composition differed between the three groups. Our results showed relatively high frequencies of haplogroup H12 in Albanians (8.8%) and less in Turks (3.3%), while haplogroups M5a1 and H7a1a were dominant in Romanies (13.7% and 10.3%, respectively) but rare in the former two. This highlights the importance of regional sampling for forensic mtDNA databasing purposes. These population data will be available on EMPOP under accession numbers EMP00644 (Albanians), EMP00645 (Romanies) and EMP00646 (Turks). PMID:25051224

  15. A correlation for the quench front velocity in the rewetting of a rod by a falling film

    International Nuclear Information System (INIS)

    Castiglia, F.; Olivieri, E.; Taibi, S.; Vella, G.

    1989-01-01

    In recent works the exact analytical solutions to the problem of the steady propagation of the quench front in the rewetting by a falling film of both hot vertical slabs and rods have been presented. These solutions furnish the temperature distribution in the solid and, in particular, the dimensioless sputtering temperature, in terms of the Biot number B and the dimensionless front velocity u. As it is well known, however, in practical applications it result more convenient to deal with an explicit - even if approximate - formula which gives the dimensionless rewetting velocity in terms of B and Θ. In view of this, in the present paper, an extension to the case of rods of a simple and reliable correlation for the prediction of the quench front velocity, already proposed for slabs, is presented. Also in this case, the correlation proves fairly satisfactory and confirms its validity in the full range of practical interest the operating parameters

  16. Blowdown and rewetting characteristics for AHWR under postulated LOCA - an analytical study

    International Nuclear Information System (INIS)

    Mukhopadhyay, D.; Chatterjee, B.

    2015-01-01

    ECCS injection leads to change of phase from mist to slug/ annular mist regime. The modelling of fuel cluster (single channel to three sub-channel) is found to have a bearing on the PCT and rewetting period

  17. Drying/rewetting cycles mobilize old C from deep soils from a California annual grassland

    OpenAIRE

    Schimel, JP; Wetterstedt, JAM; Holden, PA; Trumbore, SE

    2011-01-01

    We measured the 14 C and 13 C signatures of CO 2 respired from surface and deep soils released through multiple dry/rewetting cycles in laboratory incubations. The C respired from surface soils included components fixed before and after the 1960s. However, that respired from deep soils was derived from organic matter with a mean turnover time estimated in the range of 650-850 years. This reinforces previous research suggesting that a substantial amount of deep soil C is chemically labile b...

  18. The sensitivity of Sphagnum to surface layer conditions in a re-wetted bog: a simulation study of water stress

    NARCIS (Netherlands)

    Schouwenaars, J.M.; Gosen, A.M.

    2007-01-01

    The behaviour of the water table in re-wetted bogs varies widely between different locations so that recolonising Sphagnum is vulnerable to water stress, especially when the water table is drawn down in summer. It is important to understand how physical site conditions influence the occurrence of

  19. Flight distance of mosquitoes (Culicidae): A metadata analysis to support the management of barrier zones around rewetted and newly constructed wetlands

    NARCIS (Netherlands)

    Verdonschot, P.F.M.; Besse-Lototskaya, A.A.

    2013-01-01

    Society responds to changes in climate and land use via mitigation measures, including rainwater retention and storage in rewetted and newly constructed wetlands. Humans living close to these wetlands express concerns about future mosquito nuisance situations, and request the necessary distance

  20. A numerical solution model of the rewetting of a nuclear fuel rod

    International Nuclear Information System (INIS)

    Braz Filho, F.A.

    1984-01-01

    The study of thermal behaviour of a nuclear reactor fuel rod during the reflooding phase of the loss-of-coolant accident (LOCA) is presented. A mathematical model and a numerical scheme were proposed in order to solve the bidimensional heat conduction equation in cylindrical coordinates. The phenomenon of reflooding is not completely understood. One of the main difficulties is to estimate the heat transfer coefficient (h). For this reason two different models were elaborated: in the first three regions are considered and in each region h is considered constant; in the second the h profile is adjusted according to the boiling curve. The three region model yields satisfactory results at high and low mass flows while the 'boiling curve' model yields reasonable at low flows. (Author) [pt

  1. An analytical study of thermo-hydrodynamic behaviour of the reflood-phase during a LOCA

    International Nuclear Information System (INIS)

    Murao, Y.

    1977-12-01

    The objectives of this study are - the check of the quench model proposed by the author and T. Sudoh, - the establishment of the thermo-hydrodynamics downstream from the quench front, and - the stabilization of the numerical calculations. In order to study these therms, the new version of the reflood analysis code 'REFLA-1D' was developed. The quench modes were classified into the following three types: 1) Liquid column type (rewetting by subcooled water), 2) Dryout type (annular flow type, rewetting by saturated water), and 3) Rewetting type (entire surface temperature higher than rewetting temperature). For the thermo-hydrodynamic model downstream from the quench front, the flow pattern was divided into the five regimes: 1) Subcooled film boiling regime, 2) Transition flow regime, 3) Dispersed flow regime, 4) Superheated steam flow regime, and 5) Rewetted regime. To stabilze the numerical calculation and shorten the computing time, the Lagrangian form of the energy equation of gase phase and dispersed flow region was used instead of the Eulerian form. Considerably close agreement between three PWR-FLECHT tests and the calculated results for the critical Weber number Wec=1.0 was obtained for fuel clad surface temperature and quench time except in earlier stage before turnaround, but poor agreement for the heat transfer characteristics in the transition flow region defined between the quench front and the dispersed flow region. The calculation was relatively stable and the computing time is about the same as a real time for a IBM 370-158 computer. (orig.) [de

  2. Paludiculture as a chance for peatland and climate: the greenhouse gas balance of biomass production on two rewetted peatlands does not differ from the natural state

    Science.gov (United States)

    Günther, Anke; Huth, Vytas; Jurasinski, Gerald; Albrecht, Kerstin; Glatzel, Stephan

    2015-04-01

    In Europe, rising prices for farm land make it increasingly difficult for government administrations to compete with external investors during the acquisition of land for wetland conservation. Thus, adding economic value to these, otherwise "lost", areas by combining extensive land use with nature conservation efforts could increase the amount of ground available for wetland restoration. Against this background, the concept of paludiculture aims to provide biomass for multiple purposes from peatlands with water tables high enough to conserve the peat body. However, as plants have been shown to contribute to greenhouse gas exchange in peatlands, manipulating the vegetation (by harvesting, sowing etc.) might alter the effect of the restored peatlands on climate. Here, we present greenhouse gas data from two experimental paludiculture systems on formerly drained intensive grasslands in northern Germany. In a fen that has been rewetted more than 15 years ago three species of reed plants were harvested to simulate biomass production for bioenergy and as construction material. And in a peat bog that has been converted from drained grassland to a field with a controlled water table around ground surface Sphagnum mosses were cultivated to provide an alternative growing substrate for horticulture. In both systems, we determined carbon dioxide, methane, and nitrous oxide exchange using closed chambers over two years. Additionally, water and peat chemistry and environmental parameters as recorded by a weather station were analyzed. Both restored peatlands show greenhouse gas balances comparable to those of natural ecosystems. Nitrous oxide was not emitted in either system. Fluctuations of the emissions reflect changes in weather conditions across the study years. In the fen, relative emission patterns between plant species were not constant over time. We did not find a negative short-term effect of biomass harvest or Sphagnum cultivation on net greenhouse gas balances

  3. Dynamic conductivity modified by impurity resonant states in doping three-dimensional Dirac semimetals

    Science.gov (United States)

    Li, Shuai; Wang, Chen; Zheng, Shi-Han; Wang, Rui-Qiang; Li, Jun; Yang, Mou

    2018-04-01

    The impurity effect is studied in three-dimensional Dirac semimetals in the framework of a T-matrix method to consider the multiple scattering events of Dirac electrons off impurities. It has been found that a strong impurity potential can significantly restructure the energy dispersion and the density of states of Dirac electrons. An impurity-induced resonant state emerges and significantly modifies the pristine optical response. It is shown that the impurity state disturbs the common longitudinal optical conductivity by creating either an optical conductivity peak or double absorption jumps, depending on the relative position of the impurity band and the Fermi level. More importantly, these conductivity features appear in the forbidden region between the Drude and interband transition, completely or partially filling the Pauli block region of optical response. The underlying physics is that the appearance of resonance states as well as the broadening of the bands leads to a more complicated selection rule for the optical transitions, making it possible to excite new electron-hole pairs in the forbidden region. These features in optical conductivity provide valuable information to understand the impurity behaviors in 3D Dirac materials.

  4. Colliding winds: Interaction regions with strong heat conduction

    International Nuclear Information System (INIS)

    Imamura, J.N.; Chevalier, R.A.

    1984-01-01

    The interaction of fast stellar wind with a slower wind from previous mass loss gives rise to a region of hot, shocked gas. We obtain self-similar solutions for the interaction region under the assumptions of constant mass loss rate and wind velocity for the two winds, conversion of energy in the shock region, and either isothermal electrons and adiabatic ions or isothermal electrons ad ions in the shocked region. The isothermal assumption is intended to show the effects of strog heat conduction. The solutions have no heat conduction through the shock waves and assume that the electron and ion temperatures are equilibriated in the shock waves. The one-temperature isothermal solutions have nearly constant density through the shocked region, while the two-temperature solutions are intermediate between the one-temperature adiabatic and isothermal solutions. In the two-temperature solutions, the ion temperature goes to zero at the point where the gas comoves with the shocked region and the density peaks at this point. The solution may qualitatively describe the effects of heat conduction on interaction regions in the solar wind. It will be important to determine whether the assumption of no thermal waves outside the shocked region applies to shock waves in the solar wind

  5. Nutritional responses to soil drying and rewetting cycles under partial root-zone drying irrigation

    DEFF Research Database (Denmark)

    Wang, Yaosheng; Jensen, Christian Richardt; Liu, Fulai

    2017-01-01

    signaling that regulates stomatal aperture. PRI induced soil DRW cycles and more soil water dynamics in the root zone enhance soil nutrient mineralization process and thus increase the bioavailability of soil nutrients, resulting in improved nitrogen (N) and phosphorus (P) uptake, in which soil microbial...... processes play a key role. Studies investigating how soil DRW cycles and water dynamics under PRI on nutrient transport in soil solution, soil microbe mediated P transformation, interactions between phytohormones and nutrient uptake, root morphological and architectural traits for nutrient acquisition......Abstract Repeated soil drying and rewetting (DRW) cycles occur in rainfed and irrigated agriculture. The intensity and frequency of DRW cycles regulate both microbial physiology and soil physical processes, hereby affecting the mineralization and immobilization of soil nutrients...

  6. Regional absolute conductivity reconstruction using projected current density in MREIT

    International Nuclear Information System (INIS)

    Sajib, Saurav Z K; Kim, Hyung Joong; Woo, Eung Je; Kwon, Oh In

    2012-01-01

    Magnetic resonance electrical impedance tomography (MREIT) is a non-invasive technique for imaging the internal conductivity distribution in tissue within an MRI scanner, utilizing the magnetic flux density, which is introduced when a current is injected into the tissue from external electrodes. This magnetic flux alters the MRI signal, so that appropriate reconstruction can provide a map of the additional z-component of the magnetic field (B z ) as well as the internal current density distribution that created it. To extract the internal electrical properties of the subject, including the conductivity and/or the current density distribution, MREIT techniques use the relationship between the external injection current and the z-component of the magnetic flux density B = (B x , B y , B z ). The tissue studied typically contains defective regions, regions with a low MRI signal and/or low MRI signal-to-noise-ratio, due to the low density of nuclear magnetic resonance spins, short T 2 or T* 2 relaxation times, as well as regions with very low electrical conductivity, through which very little current traverses. These defective regions provide noisy B z data, which can severely degrade the overall reconstructed conductivity distribution. Injecting two independent currents through surface electrodes, this paper proposes a new direct method to reconstruct a regional absolute isotropic conductivity distribution in a region of interest (ROI) while avoiding the defective regions. First, the proposed method reconstructs the contrast of conductivity using the transversal J-substitution algorithm, which blocks the propagation of severe accumulated noise from the defective region to the ROI. Second, the proposed method reconstructs the regional projected current density using the relationships between the internal current density, which stems from a current injection on the surface, and the measured B z data. Combining the contrast conductivity distribution in the entire imaging

  7. Heat transfer correlation development and assessment: a summary and assessment of return to nucleate boiling phenomena during blowdown tests conducted at the Idaho National Engineering Laboratory (INEL)

    International Nuclear Information System (INIS)

    Eaton, A.M.; Tolman, E.L.

    1979-04-01

    The data are presented which were obtained in Loss-of-Coolant Experiments (LOCE) at Idaho National Engineering Laboratory (INEL) which demonstrate the presence of cladding rewetting after the critical heat flux has been exceeded as a viable cooling mechanism during the blowdown phase of a LOCE. A brief review of the mechanisms associated with the boiling crisis and rewetting is also provided. The relevance of INEL LOCE rewetting data to nuclear reactor licensing Evaluation Model Requirements is considered, and the conclusion is made that the elimination of rewetting and return to nucleate boiling (RNB) in Evaluation Models represents a definite conservatism

  8. Computational simulation of natural circulation and rewetting experiments using the TRAC/PF1 code

    International Nuclear Information System (INIS)

    Silva, J.D. da.

    1994-05-01

    In this work the TRAC code was used to simulate experiments of natural circulation performed in the first Brazilian integral test facility at (COPESP), Sao Paulo and a rewetting experiment in a single tube test section carried out at CDTN, Belo Horizonte, Brazil. In the first simulation the loop behavior in two transient conditions with different thermal power, namely 20 k W and 120 k W, was verified in the second one the quench front propagation, the liquid mass collected in the carry over measuring tube and the wall temperature at different elevations during the flooding experiment was measured. A comparative analysis, for code consistency, shows a good agreement between the code results and experimental data, except for the quench from velocity. (author). 15 refs, 19 figs, 12 tabs

  9. The Impact of Extreme Weather Events on Dissolved Organic Matter and Microbial Biomass of chernozem soils

    Science.gov (United States)

    Müller, Ann-Christin; Blagodatskaya, Evgenia

    2017-04-01

    The aim of this experiment was to study the impact of the extreme weather events freezing-thawing and drying-rewetting on C-, N- and P-dynamics in dissolved organic matter and microbial biomass. The three variants of a chernozem soil (Voronezh region, Russia) are (1) fertilized maize cropping, (2) unfertilized maize cropping and (3) a bare fallow. After both abiotic perturbations the respiration rates were generally lower in the freezing-thawing than in the drying-rewetting treatment, due to the lower temperature. The elevated respiration came along with the decay of organic matter, which was also manifested in increased mineralization of C, N and P immediately after rewetting. However, freezing-thawing had significantly less impact on C-, N- and P-mobilization. We conclude that drying-rewetting leads to an initially increased mobilization of C, N and P, which becomes obvious as increased amounts of DOM immediately after rewetting. Freezing-thawing does not affect mobilization in the same way. There, only an increased mobilization of C can be observed. Especially concerning N and P, the reaction is dependent on the form of use/cropping in both treatments.

  10. Oscillatory instability of a self-rewetting film driven by thermal modulation

    Science.gov (United States)

    Batson, William; Agnon, Yehuda; Oron, Alex

    2016-11-01

    Here we consider the self-rewetting fluids (SRWFs) that exhibit a well-defined minimum surface tension with respect to temperature, in contrast to those where surface tension decreases linearly. Utilization of SRWFs has grown significantly in the past decade, due to observations that heat transfer is enhanced in applications such as film boiling and pulsating heat pipes. With similar applications in mind, we investigate the dynamics of a thin SRWF film which is subjected to a temperature modulation in the bounding gas. A model is developed within the framework of the long-wave approximation, and a time-averaged thermocapillary driving force for destabilization is uncovered for SRWFs that results from the nonlinear surface tension. Linear analysis of the nonlinear PDE for the film thickness is used to determine the critical conditions at which this driving force destabilizes the film, and, numerical integration of this evolution equation reveals that linearly unstable perturbations saturate to regular periodic solutions (when the modulational frequency is set properly). Properties of these flows such as bifurcation and long-domain flows, where multiple unstable linear modes interact, will also be discussed.

  11. Electrical conductivity and ion diffusion in porcine meniscus: effects of strain, anisotropy, and tissue region.

    Science.gov (United States)

    Kleinhans, Kelsey L; McMahan, Jeffrey B; Jackson, Alicia R

    2016-09-06

    The purpose of the present study was to investigate the effects of mechanical strain, anisotropy, and tissue region on electrical conductivity and ion diffusivity in meniscus fibrocartilage. A one-dimensional, 4-wire conductivity experiment was employed to measure the electrical conductivity in porcine meniscus tissues from two tissue regions (horn and central), for two tissue orientations (axial and circumferential), and for three levels of compressive strain (0%, 10%, and 20%). Conductivity values were then used to estimate the relative ion diffusivity in meniscus. The water volume fraction of tissue specimens was determined using a buoyancy method. A total of 135 meniscus samples were measured; electrical conductivity values ranged from 2.47mS/cm to 4.84mS/cm, while relative ion diffusivity was in the range of 0.235 to 0.409. Results show that electrical conductivity and ion diffusion are significantly anisotropic (pmeniscus fibrocartilage, which is essential in developing new strategies to treat and/or prevent tissue degeneration. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Impact of drying-rewetting events on the response of soil microbial functions to dairyfibre and Miscanthus biochars

    Science.gov (United States)

    Bonnett, Sam; Vink, Stefanie; Baker, Kate; Saghir, Muhammad; Hornung, Andreas

    2014-05-01

    Biochar application has been shown to positively affect soil microbial functions such as reducing greenhouse gas emissions, increasing water/nutrient availability and increasing crop yields in tropical regions (Lehmann & Joseph, 2009). Understanding the dynamics of biochar application to soil microbial processes is critical for ensuring that soil quality, integrity and sustainability of the soil sub-system are maintained for crop growth. The aim of this British Ecological Society (BES) funded study was to examine the effect of two types of biochar on soil physicochemistry, GHG production, soil enzyme activities and microbial biomass in typical agricultural soil types and whether the effects were altered by drying, rewetting and flooding events. Miscanthus and dairyfibre (a mixture of straw and manure) feedstocks from Harper Adams University were pyrolyzed by Aston University at 450 °C using 100 kg/hr pyroformer technology. Two sieved soil types (sandy loam and clay loam) were mixed with dry biochar to produce 2 and 10 % w/w treatments for comparison with controls and maintained at 15 °C in temperature controlled incubators. At 0, 22, 44, 80, 101, and 114 days, soil was collected for determination of heterotrophic respiration, and microbial biomass by substrate-induced respiration (SIR), by gas headspace incubation and analysis of carbon dioxide (CO2) and nitrous oxide (N2O) by gas chromatography. Soil was sampled for the determination of water-extractable carbon, pH, and extracellular enzyme activities. Soil samples were maintained at field gravimetric water content between 0 and 44 days; air dried between 44 and 80 days; rewetted between 80 and 101 days; and flooded between 101 to 114 days. Results showed that the impact of biochar on soil microbial processes was dependent on biochar type and soil type, the level of biochar application and changes in soil moisture. Biochar affected soil pH particularly within the dairyfibre treatments, potentially due to the

  13. Copper pollution decreases the resistance of soil microbial community to subsequent dry-rewetting disturbance.

    Science.gov (United States)

    Li, Jing; Wang, Jun-Tao; Hu, Hang-Wei; Ma, Yi-Bing; Zhang, Li-Mei; He, Ji-Zheng

    2016-01-01

    Dry-rewetting (DW) disturbance frequently occurs in soils due to rainfall and irrigation, and the frequency of DW cycles might exert significant influences on soil microbial communities and their mediated functions. However, how microorganisms respond to DW alternations in soils with a history of heavy metal pollution remains largely unknown. Here, soil laboratory microcosms were constructed to explore the impacts of ten DW cycles on the soil microbial communities in two contrasting soils (fluvo-aquic soil and red soil) under three copper concentrations (zero, medium and high). Results showed that the fluctuations of substrate induced respiration (SIR) decreased with repeated cycles of DW alternation. Furthermore, the resistance values of substrate induced respiration (RS-SIR) were highest in non-copper-stressed (zero) soils. Structural equation model (SEM) analysis ascertained that the shifts of bacterial communities determined the changes of RS-SIR in both soils. The rate of bacterial community variance was significantly lower in non-copper-stressed soil compared to the other two copper-stressed (medium and high) soils, which might lead to the higher RS-SIR in the fluvo-aquic soil. As for the red soil, the substantial increase of the dominant group WPS-2 after DW disturbance might result in the low RS-SIR in the high copper-stressed soil. Moreover, in both soils, the bacterial diversity was highest in non-copper-stressed soils. Our results revealed that initial copper stress could decrease the resistance of soil microbial community structure and function to subsequent DW disturbance. Copyright © 2015. Published by Elsevier B.V.

  14. PREVALENCE OF BOVINE CRYPTOSPORIDIOSIS IN THREE ECOLOGICAL REGIONS FROM THE CENTRAL REGION OF VERACRUZ, MEXICO

    Directory of Open Access Journals (Sweden)

    Oscar O. Castelan-Hernández

    2011-11-01

    Full Text Available Prevalence of Cryptosporidium spp. in cattle from three ecological regions in the central area of the state of Veracruz, Mexico, was determined. A transversal study was conducted in 72 calves 3 to 12 months old from six production units from the municipalities of Zentla, Tlacotalpan and Manlio F. Altamirano. Fecal samples were collected from the calves and analyzed using the Kinyoun stain technique. Overall prevalence of cryptosporidiosis was 73.6 %, and by municipality it was 66.7 % in Zentla, 75 % in Tlacotalpan, and 79.2 % in Manlio F. Altamirano. Prevalence by age was 72.4 % in calves 3 months old and 74.4 % in calves 6 to 12 months old. Prevalence was higher in females (78.7 % than in males (45.5 %. Prevalence by breed was 78.8 % in Brown Swiss/Zebu, 83.3 % in Brown Swiss, 50 % in Holstein/Zebu, and 50 % in Brown Swiss/Holstein, with no difference among crosses (P > 0.05. There was no association among infection by Cryptosporidium spp. and sex, breed, age and ecological region. In conclusion, Cryptosporidium spp. is present in the dual purpose cattle production systems in the three municipalities studied located in the central region of Veracruz, Mexico.

  15. Tailoring thermal conductivity via three-dimensional porous alumina.

    Science.gov (United States)

    Abad, Begoña; Maiz, Jon; Ruiz-Clavijo, Alejandra; Caballero-Calero, Olga; Martin-Gonzalez, Marisol

    2016-12-09

    Three-dimensional anodic alumina templates (3D-AAO) are an astonishing framework with open highly ordered three-dimensional skeleton structures. Since these templates are architecturally different from conventional solids or porous templates, they teem with opportunities for engineering thermal properties. By establishing the mechanisms of heat transfer in these frameworks, we aim to create materials with tailored thermal properties. The effective thermal conductivity of an empty 3D-AAO membrane was measured. As the effective medium theory was not valid to extract the skeletal thermal conductivity of 3D-AAO, a simple 3D thermal conduction model was developed, based on a mixed series and parallel thermal resistor circuit, giving a skeletal thermal conductivity value of approximately 1.25 W·m -1 ·K -1 , which matches the value of the ordinary AAO membranes prepared from the same acid solution. The effect of different filler materials as well as the variation of the number of transversal nanochannels and the length of the 3D-AAO membrane in the effective thermal conductivity of the composite was studied. Finally, the thermal conductivity of two 3D-AAO membranes filled with cobalt and bismuth telluride was also measured, which was in good agreement with the thermal model predictions. Therefore, this work proved this structure as a powerful approach to tailor thermal properties.

  16. Tailoring thermal conductivity via three-dimensional porous alumina

    Science.gov (United States)

    Abad, Begoña; Maiz, Jon; Ruiz-Clavijo, Alejandra; Caballero-Calero, Olga; Martin-Gonzalez, Marisol

    2016-01-01

    Three-dimensional anodic alumina templates (3D-AAO) are an astonishing framework with open highly ordered three-dimensional skeleton structures. Since these templates are architecturally different from conventional solids or porous templates, they teem with opportunities for engineering thermal properties. By establishing the mechanisms of heat transfer in these frameworks, we aim to create materials with tailored thermal properties. The effective thermal conductivity of an empty 3D-AAO membrane was measured. As the effective medium theory was not valid to extract the skeletal thermal conductivity of 3D-AAO, a simple 3D thermal conduction model was developed, based on a mixed series and parallel thermal resistor circuit, giving a skeletal thermal conductivity value of approximately 1.25 W·m−1·K−1, which matches the value of the ordinary AAO membranes prepared from the same acid solution. The effect of different filler materials as well as the variation of the number of transversal nanochannels and the length of the 3D-AAO membrane in the effective thermal conductivity of the composite was studied. Finally, the thermal conductivity of two 3D-AAO membranes filled with cobalt and bismuth telluride was also measured, which was in good agreement with the thermal model predictions. Therefore, this work proved this structure as a powerful approach to tailor thermal properties. PMID:27934930

  17. Prevalence of intestinal parasites in three socioeconomically-different regions of Sivas, Turkey.

    Science.gov (United States)

    Celiksöz, Ali; Güler, Nuran; Güler, Güngör; Oztop, A Yasemin; Degerli, Serpil

    2005-06-01

    The study was carried out to determine the prevalence of parasites in three socioeconomically-different regions (Alibaba, Esentepe, and Cayboyu) of Sivas, Turkey, to determine the most accurate method for the diagnosis of taeniasis and enterobiasis, to determine the importance of household visits in primary healthcare to control parasitic diseases, and to treat intestinal parasitic diseases in those regions. Both stool specimens and cellophane tape (CT) samples were taken from 1,864 participants during 641 household visits in the three regions. The age groups included were pre-school [(0-6 year(s)], primary school (7-15 years), and the upper age group (16 years and above). The total prevalence of intestinal parasites in the three regions was 37.2%. Eleven intestinal parasite species were detected in both stool specimens and CT samples. Giardia intestinalis and Enterobius vermicularis were the most frequent species identified in all the three regions. Region I (Alibaba) had a higher prevalence of parasites compared to the other two regions. There was no significant difference between Region II (Esentepe) and Region III (Cayboyu) in isolation of intestinal parasites. There were statistically significant differences between the age groups when the rates of parasitic infection were compared. The highest prevalence of parasitosis was observed among the age group of 7-15 years and in the socioeconomically lowest one of the three regions. While the most accurate way of diagnosis for taeniasis was the combined usage of the CT and direct preparation methods, the CT method was the best method for the diagnosis of enterobiasis. Thus, the local administrators in cities need to pay more attention to the prevention of parasitic infections along with improvements in educational, environmental and sanitary conditions.

  18. Transition from natural-convection-controlled freezing to conduction-controlled freezing

    International Nuclear Information System (INIS)

    Sparrow, E.M.; Ramsey, J.W.; Harris, J.S.

    1981-01-01

    Experiments were performed to study the transition between freezing controlled by natural convection in the liquid adjacent to a freezing interface and freezing controlled by heat conduction in the solidified material. The freezing took place on a cooled vertical tube immersed in an initially superheated liquid contained in an adiabatic-walled vessel. At early and intermediate times, temperature differences throughout the liquid induce a vigorous natural convection motion which retards freezing, but the temperature differences diminish with time and natural convection ebbs. At large times, the freezing rate is fully controlled by heat conduction in the solidified material. The frozen specimens for short and intermediate freezing times are smooth-surfaced and tapered, while those for large times are straight-sided and have surfaces that are overlaid with a thicket of large discrete crystals. These characteristics correspond respectively to those of natural-convection- controlled freezing and conduction-controlled freezing. At early times, the measured mass of the frozen material is identical to that for natural-convection-controlled freezing and conduction-controlled freezing. At early times, the measured mass of the frozen material is identical to that for natural-convection-controlled freezing. At later times, the frozen mass tends to approach that for conduction-controlled freezing, but a residual deficit remains

  19. Effects of Drought and Rewetting on Growth and Gas Exchange of Minor European Broadleaved Tree Species

    Directory of Open Access Journals (Sweden)

    Jörg Kunz

    2016-10-01

    Full Text Available Widespread and economically important European tree species such as Norway spruce, Scots pine, and European beech are projected to be negatively affected by the increasing intensity and frequency of dry and hot conditions in a future climate. Hence, there is an increasing need to investigate the suitability of presumably more drought tolerant species to ensure future ecological stability, biodiversity, and productivity of forests. Based on their distribution patterns and climatic envelopes, the rare, minor broadleaved tree species Sorbus torminalis ((L. CRANTZ, S. domestica (L., Acer campestre (L., and A. platanoides (L. are assumed to be drought tolerant, however, there is only limited experimental basis to support that notion. This study aimed at quantifying growth and gas exchange of seedlings of these species during drought conditions, and their capacity to recover following drought. For that purpose, they were compared to the common companion species Quercus petraea ((MATTUSCHKA LIEBL. and Fagus sylvatica (L.. Here, potted seedlings of these species were exposed to water limitation followed by rewetting cycles in a greenhouse experiment. Photosynthesis and transpiration rates, stomatal conductance as well as root and shoot growth rates indicated a high drought resistance of A. campestre and A. platanoides. Sorbus domestica showed a marked ability to recover after drought stress. Therefore, we conclude that these minor tree species have the potential to enrich forests on drought-prone sites. Results from this pot experiment need to be complemented by field studies, in which the drought response of the species is not influenced by restrictions to root development.

  20. Characterization of an Actively Controlled Three-Dimensional Turret Wake

    Science.gov (United States)

    Shea, Patrick; Glauser, Mark

    2012-11-01

    Three-dimensional turrets are commonly used for housing optical systems on airborne platforms. As bluff bodies, these geometries generate highly turbulent wakes that decrease the performance of the optical systems and the aircraft. The current experimental study looked to use dynamic suction in both open and closed-loop control configurations to actively control the turret wake. The flow field was characterized using dynamic pressure and stereoscopic PIV measurements in the wake of the turret. Results showed that the suction system was able to manipulate the wake region of the turret and could alter not only the spatial structure of the wake, but also the temporal behavior of the wake flow field. Closed-loop, feedback control techniques were used to determine a more optimal control input for the flow control. Similar control effects were seen for both the steady open-loop control case and the closed-loop feedback control configuration with a 45% reduction in the suction levels when comparing the closed-loop to the open-loop case. These results provide unique information regarding the development of the baseline three-dimensional wake and the wake with three different active flow control configurations.

  1. Effects of a conducting E layer on classical F region cross-field plasma diffusion

    International Nuclear Information System (INIS)

    Vickrey, J.F.; Kelley, M.C.

    1982-01-01

    The rate of cross-field plasma diffusion in the F region ionosphere is significantly increased when the magnetic field lines thread a highly conducting E region below. This reduces the lifetime of small-scale F region electron density irregularities in the polar ionosphere where the presence of a highly conducting E region is comonplace. A simple mmodel is developed to describe the effects of a conducting E layer on classical F region plasma diffusion. In the absence of an E region, the difference in ion and electron diffusion rates leads to a charge separation and, hence, to an electrostatic field that retards ion diffusion. When the highly conducting magnetic field lines are tied to a conducting E region, however, electrons can flow along B to reduce the ambipolar diffusion electric field, and ions can proceed perpendicular to B at a rate approaching their own (higher) diffusion velocity. It is shown that the enhanced total diffusion rate that results depends strongly on the height of the F layer and on the ratio of the E to F region Pedersen conductivities

  2. Research on frequency control strategy of interconnected region based on fuzzy PID

    Science.gov (United States)

    Zhang, Yan; Li, Chunlan

    2018-05-01

    In order to improve the frequency control performance of the interconnected power grid, overcome the problems of poor robustness and slow adjustment of traditional regulation, the paper puts forward a frequency control method based on fuzzy PID. The method takes the frequency deviation and tie-line deviation of each area as the control objective, takes the regional frequency deviation and its deviation as input, and uses fuzzy mathematics theory, adjusts PID control parameters online. By establishing the regional frequency control model of water-fire complementary power generation in MATLAB, the regional frequency control strategy is given, and three control modes (TBC-FTC, FTC-FTC, FFC-FTC) are simulated and analyzed. The simulation and experimental results show that, this method has better control performance compared with the traditional regional frequency regulation.

  3. Mantle electrical conductivity profile of Niger delta region

    Indian Academy of Sciences (India)

    The mantle electrical conductivity-depth profile of the Niger delta region in Nigeria has been determined using solar quiet day ionospheric current (Sq).The magnetometer data obtained in 2010 from geomagnetic stations installed in Lagos by magnetic dataset (MAGDAS) in 2008 and data from magnetometers installed in ...

  4. Characterization and evolution of the mitochondrial DNA control region in hornbills (Bucerotiformes).

    Science.gov (United States)

    Delport, Wayne; Ferguson, J Willem H; Bloomer, Paulette

    2002-06-01

    We determined the mitochondrial DNA control region sequences of six Bucerotiformes. Hornbills have the typical avian gene order and their control region is similar to other avian control regions in that it is partitioned into three domains: two variable domains that flank a central conserved domain. Two characteristics of the hornbill control region sequence differ from that of other birds. First, domain I is AT rich as opposed to AC rich, and second, the control region is approximately 500 bp longer than that of other birds. Both these deviations from typical avian control region sequence are explainable on the basis of repeat motifs in domain I of the hornbill control region. The repeat motifs probably originated from a duplication of CSB-1 as has been determined in chicken, quail, and snowgoose. Furthermore, the hornbill repeat motifs probably arose before the divergence of hornbills from each other but after the divergence of hornbills from other avian taxa. The mitochondrial control region of hornbills is suitable for both phylogenetic and population studies, with domains I and II probably more suited to population and phylogenetic analyses, respectively.

  5. Three-dimensional Simulation of Gas Conductance Measurement Experiments on Alcator C-Mod

    International Nuclear Information System (INIS)

    Stotler, D.P.; LaBombard, B.

    2004-01-01

    Three-dimensional Monte Carlo neutral transport simulations of gas flow through the Alcator C-Mod subdivertor yield conductances comparable to those found in dedicated experiments. All are significantly smaller than the conductance found with the previously used axisymmetric geometry. A benchmarking exercise of the code against known conductance values for gas flow through a simple pipe provides a physical basis for interpreting the comparison of the three-dimensional and experimental C-Mod conductances

  6. Stiffness characteristics of compliant three segment leg with the self-stable region in slow and fast running

    Energy Technology Data Exchange (ETDEWEB)

    Kwak, Oh Seok; Ha, Sung Mok; Lee, Dong Ha [Convergence Research Center for WellnessDaegu Gyeongbuk Institute of Science and TechnologyDaegu (Korea, Republic of)

    2016-12-15

    In this paper, we propose the stiffness characteristics of compliant three segment leg that can have a self-stable region in slow and fast running. This proposition can contribute to reducing the control effort and enhancing the locomotion energy efficiency for the compliant three segment legged robot in slow and fast running. Previous research indicated that the running self-stable region of the spring-mass system is located in a relatively fast running region and that of the two segment leg is located in a relatively slow running region. In this paper, we analyze the stiffness characteristics of the spring-mass system and the two segment leg to explain the previous research results. From this analysis, we propose the stiffness characteristics of the compliant three segment leg with a self-stable region in slow and fast running. We further design the compliant three segment leg based on this proposition and check its structural stability. We examine the running self-stable region of this compliant three segment leg to determine whether it has a self-stable region in slow and fast running. We also examine the walking self-stable region of this compliant three segment leg.

  7. Transcriptomic profiling of central nervous system regions in three species of honey bee during dance communication behavior.

    Directory of Open Access Journals (Sweden)

    Moushumi Sen Sarma

    2009-07-01

    Full Text Available We conducted a large-scale transcriptomic profiling of selected regions of the central nervous system (CNS across three species of honey bees, in foragers that were performing dance behavior to communicate to their nestmates the location, direction and profitability of an attractive floral resource. We used microarrays to measure gene expression in bees from Apis mellifera, dorsata and florea, species that share major traits unique to the genus and also show striking differences in biology and dance communication. The goals of this study were to determine the extent of regional specialization in gene expression and to explore the molecular basis of dance communication.This "snapshot" of the honey bee CNS during dance behavior provides strong evidence for both species-consistent and species-specific differences in gene expression. Gene expression profiles in the mushroom bodies consistently showed the biggest differences relative to the other CNS regions. There were strong similarities in gene expression between the central brain and the second thoracic ganglion across all three species; many of the genes were related to metabolism and energy production. We also obtained gene expression differences between CNS regions that varied by species: A. mellifera differed the most, while dorsata and florea tended to be more similar.Species differences in gene expression perhaps mirror known differences in nesting habit, ecology and dance behavior between mellifera, florea and dorsata. Species-specific differences in gene expression in selected CNS regions that relate to synaptic activity and motor control provide particularly attractive candidate genes to explain the differences in dance behavior exhibited by these three honey bee species. Similarities between central brain and thoracic ganglion provide a unique perspective on the potential coupling of these two motor-related regions during dance behavior and perhaps provide a snapshot of the energy

  8. Measuring three-dimensional flow structures in the conductive airways using 3D-PTV

    Science.gov (United States)

    Janke, Thomas; Schwarze, Rüdiger; Bauer, Katrin

    2017-10-01

    Detailed information about flow patterns and mass transport in the conductive airways is of crucial interest to improve ventilation strategies as well as targeted drug delivery. Despite a vast number of flow studies in this field, there is still a dearth in experimental data of three-dimensional flow patterns, in particular for the validation of numerical results. Therefore, oscillating flow within a realistic model of the upper human conductive airways is studied here experimentally. The investigated range of Reynolds numbers is Re = 250-2000 and the Womersley number is varied between α = 1.9-5.1, whereby physiological flow at rest conditions is included. In employing the three-dimensional particle tracking velocimetry measurement technique, we can directly visualize airway specific flow structures as well as examine Lagrangian trajectory statistics, which has not been covered to date. The systematic variation of characteristic flow parameters in combination with the advanced visualization technique sheds new light on the mechanisms of evolving flow patterns. By determining Lagrangian properties such as pathline curvature and torsion, we find that both strongly depend on the Reynolds number. Moreover, the probability density function of the curvature reveals a unique shape for certain flow regions and resembles a turbulent like behavior at the small scales.

  9. Production function analysis for smallholder semi-subsistence and semi-commercial poultry production systems in three agro-ecological regions in Northern provinces of Vietnam

    DEFF Research Database (Denmark)

    Tung, Dinh Xuan; Rasmussen, Svend

    2005-01-01

    A formal cross section survey of 360 smallholder poultry keeping farms located in three agro-ecological regions in Vietnam was conducted. Cobb-Douglas production functions were applied to analyse and compare semi-subsistence and semi-commercial smallholder poultry systems in three regions...

  10. Regional Air Pollutions in Three Different Regions of Asia From a Transcontinental Transport Perspective

    Science.gov (United States)

    Pochanart, P.; Kanaya, Y.; Komazaki, Y.; Liu, Y.; Akimoto, H.

    2007-12-01

    Asia is known as one of the regions with the fastest rate of growing in industrialization and urbanization. As a result, the rapid increases of large-scale air pollution in Asia emerge as a serious concern at both domestic and international levels. Apart from the problems of air quality degradation, emission control, environmental risk, and health effect in a domestic level, evidences from scientific studies indicate that by the long-range transport, Asian air pollution is becoming a global problem. Observations and model studies confirm that air pollution from Asia could be transported to North America or farther. In this work, we investigate the Asian air pollutions, in particular ozone and some other atmospheric components such as carbon monoxide and black carbon, from the ground- based observations in the three different regions, namely 1) background region of Siberia and central Asia, 2) highly anthropogenic region in eastern China, and 3) the rim region of the Asia-Pacific. In a transcontinental transport perspective, these regions are regarded as the inflow region, source region, and outflow region of Asia, respectively. From the results, it is found that the influences from large-scale emission in East Asia are observed clearly in the source region, and to the significant extent in the outflow region. For the inflow region of Asia, our data in Siberia and Kyrgyzstan indicate that air masses in this region are mostly intact from large-scale anthropogenic emission, and remain much of the global background atmospheric pollution characteristic. When the air masses are transported to source region, the air pollutants level increased sharply and frequent episodes of extremely high pollutions have been observed. Our results show good correlation between the residence time of air masses over the source region in eastern China and the observed levels of air pollutants verifying the strong enhancements by anthropogenic emissions from industrialization and

  11. Supply evaluation of a herbaceous and woody energy crop at three midwest regions

    International Nuclear Information System (INIS)

    English, B.C.; Dillivan, K.D.; Ojo, M.A.

    1994-01-01

    While substantial research has been conducted on the argronomic issues of biomass production and on the processes of converting biofuel crops into energy, little work has been completed analyzing the economic and physical impacts of biofuel production on an agriculturally based region. Acres currently devoted to traditional crops will be replaced by biomass crops if such a conversion proves to be economically attractive. These shifts could have impacts on local and regional levels of farm income, current farmland market values, commodity prices received, and the demand for and prices of farm level inputs. This paper examines the economic and physical ramifications of introducing biomass production to three Midwest regions centered in the following counties; Cass County, North Dakota, Olmsted County, Minnesota, and Orange County, Indiana. Using a regional linear programming model that maximizes net returns to producers subject to several constraints, a supply curve for biomass is developed for each of the three regions. The model predicts that at a plant gate price of $26, $40, and $52 per dry ton, biomass begins to enter into production in the Cass, Olmsted, and Orange Regions respectively. Prices of $28, $44, and $54 per dry ton of biomass are sufficient to supply a quantity necessary to operate a power plant requiring 5,000 dry tons per day in Cass, Olmsted, and Orange regions respectively. In the Olmsted and Orange regions, biomass production results in fertilizer being applied, however, in the Cass Region a slight increase in fertilizer use corresponds to biomass production

  12. Controlling Thermal Conduction by Graded Materials

    Science.gov (United States)

    Ji, Qin; Huang, Ji-Ping

    2018-04-01

    Manipulating thermal conductivities are fundamentally important for controlling the conduction of heat at will. Thermal cloaks and concentrators, which have been extensively studied recently, are actually graded materials designed according to coordinate transformation approaches, and their effective thermal conductivity is equal to that of the host medium outside the cloak or concentrator. Here we attempt to investigate a more general problem: what is the effective thermal conductivity of graded materials? In particular, we perform a first-principles approach to the analytic exact results of effective thermal conductivities of materials possessing either power-law or linear gradation profiles. On the other hand, by solving Laplace’s equation, we derive a differential equation for calculating the effective thermal conductivity of a material whose thermal conductivity varies along the radius with arbitrary gradation profiles. The two methods agree with each other for both external and internal heat sources, as confirmed by simulation and experiment. This work provides different methods for designing new thermal metamaterials (including thermal cloaks and concentrators), in order to control or manipulate the transfer of heat. Support by the National Natural Science Foundation of China under Grant No. 11725521, by the Science and Technology Commission of Shanghai Municipality under Grant No. 16ZR1445100

  13. Regional impact of climate on Japanese encephalitis in areas located near the three gorges dam.

    Directory of Open Access Journals (Sweden)

    Yuntao Bai

    Full Text Available BACKGROUND: In this study, we aim to identify key climatic factors that are associated with the transmission of Japanese encephalitis virus in areas located near the Three Gorges Dam, between 1997 and 2008. METHODS: We identified three geographical regions of Chongqing, based on their distance from the Three Gorges Dam. Collectively, the three regions consisted of 12 districts from which study information was collected. Zero-Inflated Poisson Regression models were run to identify key climatic factors of the transmission of Japanese encephalitis virus for both the whole study area and for each individual region; linear regression models were conducted to examine the fluctuation of climatic variables over time during the construction of the Three Gorges Dam. RESULTS: Between 1997 and 2008, the incidence of Japanese encephalitis decreased throughout the entire city of Chongqing, with noticeable variations taking place in 2000, 2001 and 2006. The eastern region, which is closest to the Three Gorges Dam, suffered the highest incidence of Japanese encephalitis, while the western region experienced the lowest incidence. Linear regression models revealed that there were seasonal fluctuations of climatic variables during this period. Zero-Inflated Poisson Regression models indicated a significant positive association between temperature (with a lag of 1 and 3 months and Japanese encephalitis incidence, and a significant negative association between rainfall (with a lag of 0 and 4 months and Japanese encephalitis incidence. CONCLUSION: The spatial and temporal trends of Japanese encephalitis incidence that occurred in the City of Chongqing were associated with temperature and rainfall. Seasonal fluctuations of climatic variables during this period were also observed. Additional studies that focus on long-term data collection are needed to validate the findings of this study and to further explore the effects of the Three Gorges Dam on Japanese

  14. ZnO based transparent conductive oxide films with controlled type of conduction

    Energy Technology Data Exchange (ETDEWEB)

    Zaharescu, M., E-mail: mzaharescu@icf.ro [Institute of Physical Chemistry “Ilie Murgulescu”, Romanian Academy, 202 Splaiul Independentei, 060021 Bucharest (Romania); Mihaiu, S., E-mail: smihaiu@icf.ro [Institute of Physical Chemistry “Ilie Murgulescu”, Romanian Academy, 202 Splaiul Independentei, 060021 Bucharest (Romania); Toader, A. [Institute of Physical Chemistry “Ilie Murgulescu”, Romanian Academy, 202 Splaiul Independentei, 060021 Bucharest (Romania); Atkinson, I., E-mail: irinaatkinson@yahoo.com [Institute of Physical Chemistry “Ilie Murgulescu”, Romanian Academy, 202 Splaiul Independentei, 060021 Bucharest (Romania); Calderon-Moreno, J.; Anastasescu, M.; Nicolescu, M.; Duta, M.; Gartner, M. [Institute of Physical Chemistry “Ilie Murgulescu”, Romanian Academy, 202 Splaiul Independentei, 060021 Bucharest (Romania); Vojisavljevic, K.; Malic, B. [Institute Jožef Stefan, Ljubljana (Slovenia); Ivanov, V.A.; Zaretskaya, E.P. [State Scientific and Production Association “Scientific-Practical Materials Research Center of the National Academy of Science Belarus, P. Brovska str.19, 220072, Minsk (Belarus)

    2014-11-28

    The transparent conductive oxide films with controlled type of conduction are of great importance and their preparation is intensively studied. In our work, the preparation of such films based on doped ZnO was realized in order to achieve controlled type of conduction and high concentration of the charge carriers. Sol–gel method was used for films preparation and several dopants were tested (Sn, Li, Ni). Multilayer deposition was performed on several substrates: SiO{sub 2}/Si wafers, silica-soda-lime and/or silica glasses. The structural and morphological characterization of the obtained films were done by scanning electron microscopy, X-ray diffraction, X-ray fluorescence, X-ray photoelectron spectroscopy and atomic force microscopy respectively, while spectroscopic ellipsometry and transmittance measurements were done for determination of optical properties. The selected samples with the best structural, morphological and optical properties were subjected to electrical measurement (Hall and Seebeck effect). In all studied cases, samples with good adherence and homogeneous morphology as well as monophasic wurtzite type structure were obtained. The optical constants (refractive index and extinction coefficient) were calculated from spectroscopic ellipsometry data using Cauchy model. Films with n- or p-type conduction were obtained depending on the composition, number of deposition and thermal treatment temperature. - Highlights: • Transparent conductive ZnO based thin films were prepared by the sol–gel method. • Controlled type of conduction is obtained in (Sn, Li) doped and Li-Ni co-doped ZnO films. • Hall and Seebeck measurements proved the p-type conductivity for Li-Ni co-doped ZnO films. • The p-type conductivity was maintained even after 4-months of storage. • Influence of dopant- and substrate-type on the ZnO films properties was established.

  15. Post-CHF low-void heat transfer of water: measurements in the complete transition boiling region at atmospheric pressure

    International Nuclear Information System (INIS)

    Johannsen, K.; Meinen, W.

    1984-01-01

    An experimental investigation of low-void heat transfer of water has been performed in the range of CHF and the minimum stable film boiling temperature. The heat transfer system used consists of a vertically mounted copper tube of 1 cm I.D. and 5 cm length with surface-temperature controlled, indirect Joule heating. Results are presented for upflowing water at inverted annular flow conditions in the inlet subcooling range of 2.5 - 40 0 C and mass flux range of 137-600 kg/m 2 s in terms of boiling curves and heat transfer coefficients versus wall temperature. Heat transfer in the stationary rewetting front, which occurs within the test section during operation in the transition boiling mode, is also dealt with. At high mass flux, occurrence of an inverse rewetting front has been observed. It is also noted that, at fixed location, minimum heat flux observed is usually not associated with the minimum stable film boiling temperature

  16. Scattering and conductance quantization in three-dimensional metal nanocontacts

    DEFF Research Database (Denmark)

    Brandbyge, Mads; Jacobsen, Karsten Wedel; Nørskov, Jens Kehlet

    1997-01-01

    The transmission through three-dimensional nanocontacts is calculated in the presence of localized scattering centers and boundary scattering using a coupled-channel recursion method. Simple confining potentials are used to investigate how robust the observation of quantized conductance is with r...

  17. Estimation of mesophyll conductance to CO2 flux by three different methods

    International Nuclear Information System (INIS)

    Loreto, F.; Harley, P.C.; Di Marco, G.; Sharkey, T.D.

    1992-01-01

    The resistance to diffusion of CO2 from the intercellular airspaces within the leaf through the mesophyll to the sites of carboxylation during photosynthesis was measured using three different techniques, The three techniques include a method based on discrimination against the heavy stable isotope of carbon, 13C, and two modeling methods. The methods rely upon different assumptions, but the estimates of mesophyll conductance were similar with all three methods. The mesophyll conductance of leaves from a number of species was about 1.4 times the stomatal conductance for CO2 diffusion determined in unstressed plants at high light. The relatively low CO2 partial pressure inside chloroplasts of plants with a low mesophyll conductance did not lead to enhanced O2 sensitivity of photosynthesis because the low conductance caused a significant drop in the chloroplast CO2 Partial pressure upon switching to low O2. We found no correlation between mesophyll conductance and the ratio of internal leaf area to leaf surface area and only a weak correlation between mesophyll conductance and the proportion of leaf volume occupied by air. Mesophyll conductance was independent of CO2 and O2 partial pressure during the measurement, indicating that a true physical parameter, independent of biochemical effects, was being measured. No evidence for accumulating mechanisms was found. Some plants, notably Citrus aurantium and Simmondsia chinensis, had very low conductances that limit the rate of photosynthesis these plants can attain at atmospheric CO2 level

  18. Tuning Nanocrystal Surface Depletion by Controlling Dopant Distribution as a Route Toward Enhanced Film Conductivity

    Science.gov (United States)

    Staller, Corey M.; Robinson, Zachary L.; Agrawal, Ankit; Gibbs, Stephen L.; Greenberg, Benjamin L.; Lounis, Sebastien D.; Kortshagen, Uwe R.; Milliron, Delia J.

    2018-05-01

    Electron conduction through bare metal oxide nanocrystal (NC) films is hindered by surface depletion regions resulting from the presence of surface states. We control the radial dopant distribution in tin-doped indium oxide (ITO) NCs as a means to manipulate the NC depletion width. We find in films of ITO NCs of equal overall dopant concentration that those with dopant-enriched surfaces show decreased depletion width and increased conductivity. Variable temperature conductivity data shows electron localization length increases and associated depletion width decreases monotonically with increased density of dopants near the NC surface. We calculate band profiles for NCs of differing radial dopant distributions and, in agreement with variable temperature conductivity fits, find NCs with dopant-enriched surfaces have narrower depletion widths and longer localization lengths than those with dopant-enriched cores. Following amelioration of NC surface depletion by atomic layer deposition of alumina, all films of equal overall dopant concentration have similar conductivity. Variable temperature conductivity measurements on alumina-capped films indicate all films behave as granular metals. Herein, we conclude that dopant-enriched surfaces decrease the near-surface depletion region, which directly increases the electron localization length and conductivity of NC films.

  19. Source apportionment of PM2.5 at the Lin'an regional background site in China with three receptor models

    Science.gov (United States)

    Deng, Junjun; Zhang, Yanru; Qiu, Yuqing; Zhang, Hongliang; Du, Wenjiao; Xu, Lingling; Hong, Youwei; Chen, Yanting; Chen, Jinsheng

    2018-04-01

    Source apportionment of fine particulate matter (PM2.5) were conducted at the Lin'an Regional Atmospheric Background Station (LA) in the Yangtze River Delta (YRD) region in China from July 2014 to April 2015 with three receptor models including principal component analysis combining multiple linear regression (PCA-MLR), UNMIX and Positive Matrix Factorization (PMF). The model performance, source identification and source contribution of the three models were analyzed and inter-compared. Source apportionment of PM2.5 was also conducted with the receptor models. Good correlations between the reconstructed and measured concentrations of PM2.5 and its major chemical species were obtained for all models. PMF resolved almost all masses of PM2.5, while PCA-MLR and UNMIX explained about 80%. Five, four and seven sources were identified by PCA-MLR, UNMIX and PMF, respectively. Combustion, secondary source, marine source, dust and industrial activities were identified by all the three receptor models. Combustion source and secondary source were the major sources, and totally contributed over 60% to PM2.5. The PMF model had a better performance on separating the different combustion sources. These findings improve the understanding of PM2.5 sources in background region.

  20. Distributed Control of Heat Conduction in Thermal Inductive Materials with 2D Geometrical Isomorphism

    Directory of Open Access Journals (Sweden)

    Chia-Yu Chou

    2014-09-01

    Full Text Available In a previous study we provided analytical and experimental evidence that some materials are able to store entropy-flow, of which the heat-conduction behaves as standing waves in a bounded region small enough in practice. In this paper we continue to develop distributed control of heat conduction in these thermal-inductive materials. The control objective is to achieve subtle temperature distribution in space and simultaneously to suppress its transient overshoots in time. This technology concerns safe and accurate heating/cooling treatments in medical operations, polymer processing, and other prevailing modern day practices. Serving for distributed feedback, spatiotemporal H ∞ /μ control is developed by expansion of the conventional 1D-H ∞ /μ control to a 2D version. Therein 2D geometrical isomorphism is constructed with the Laplace-Galerkin transform, which extends the small-gain theorem into the mode-frequency domain, wherein 2D transfer-function controllers are synthesized with graphical methods. Finally, 2D digital-signal processing is programmed to implement 2D transfer-function controllers, possibly of spatial fraction-orders, into DSP-engine embedded microcontrollers.

  1. Perceived discrimination, serotonin transporter linked polymorphic region status, and the development of conduct problems.

    Science.gov (United States)

    Brody, Gene H; Beach, Steven R H; Chen, Yi-Fu; Obasi, Ezemenari; Philibert, Robert A; Kogan, Steven M; Simons, Ronald L

    2011-05-01

    This study examined the prospective relations of adolescents' perceptions of discrimination and their genetic status with increases in conduct problems. Participants were 461 African American youths residing in rural Georgia (Wave 1 mean age = 15.5 years) who provided three waves of data and a saliva sample from which a polymorphism in the SCL6A4 (serotonin transporter [5-HTT]) gene polymorphism known as the 5-HTT linked promoter region (5-HTTLPR) was genotyped. Data analyses using growth curve modeling indicated that perceived discrimination was significantly related to the slope of conduct problems. As hypothesized, interactions between perceived discrimination and genetic status emerged for male but not female youths. Compared with those carrying two copies of the long allele variant of 5-HTTLPR, male youths carrying one or two copies of its short allele variant evinced higher rates of conduct problems over time when they perceived high levels of racial discrimination. These findings are consistent with resilience and differential susceptibility propositions stating that genes can both foster sensitivity to adverse events and confer protection from those events.

  2. Maternal smoking during pregnancy and offspring conduct problems: Evidence from three independent genetically-sensitive research designs

    Science.gov (United States)

    Gaysina, Darya; Fergusson, David M.; Leve, Leslie D.; Horwood, John; Reiss, David; Shaw, Daniel S.; Elam, Kit K.; Natsuaki, Misaki N.; Neiderhiser, Jenae M.; Harold, Gordon T.

    2013-01-01

    Context A number of studies report an association between maternal smoking during pregnancy and offspring conduct disorder. However, past research evidences difficulty disaggregating prenatal environmental from genetic and postnatal environmental influences. Objective To examine the relationship between maternal smoking during pregnancy and offspring conduct problems among children reared by genetically-related and genetically-unrelated mothers. Design, Setting and Participants Three studies employing distinct but complementary research designs were utilized: The Christchurch Health and Development Study (a longitudinal cohort study that includes biological and adopted children), the Early Growth and Development Study (a longitudinal adoption at birth study), and the Cardiff IVF Study (genetically-related and -unrelated families; an adoption at conception study). Maternal smoking during pregnancy was measured as the average number of cigarettes/day (0, 1–9 or 10+) smoked during pregnancy. A number of possible covariates (child gender, ethnicity, birth weight, breast feeding, maternal age at birth, maternal education, family SES, family breakdown, placement age, and parenting practices) were controlled in the analyses. Main Outcome Measure Child conduct problems (age 4–10 years) reported by parents and/or teachers using the Rutter and Conners behaviour scales, the Child Behavior Checklist and Children's Behavior Questionnaire, and the Strengths and Difficulties Questionnaire. Results A significant association between maternal smoking during pregnancy and child conduct problems was observed among children reared by genetically-related and genetically-unrelated mothers. Results from a meta-analysis affirmed this pattern of findings across pooled study samples. Conclusions Findings across the three studies using a complement of genetically-sensitive research designs suggest smoking during pregnancy is a prenatal risk factor for offspring conduct problems, when

  3. Multi-region fuzzy logic controller with local PID controllers for U-tube steam generator in nuclear power plant

    Directory of Open Access Journals (Sweden)

    Puchalski Bartosz

    2015-12-01

    Full Text Available In the paper, analysis of multi-region fuzzy logic controller with local PID controllers for steam generator of pressurized water reactor (PWR working in wide range of thermal power changes is presented. The U-tube steam generator has a nonlinear dynamics depending on thermal power transferred from coolant of the primary loop of the PWR plant. Control of water level in the steam generator conducted by a traditional PID controller which is designed for nominal power level of the nuclear reactor operates insufficiently well in wide range of operational conditions, especially at the low thermal power level. Thus the steam generator is often controlled manually by operators. Incorrect water level in the steam generator may lead to accidental shutdown of the nuclear reactor and consequently financial losses. In the paper a comparison of proposed multi region fuzzy logic controller and traditional PID controllers designed only for nominal condition is presented. The gains of the local PID controllers have been derived by solving appropriate optimization tasks with the cost function in a form of integrated squared error (ISE criterion. In both cases, a model of steam generator which is readily available in literature was used for control algorithms synthesis purposes. The proposed multi-region fuzzy logic controller and traditional PID controller were subjected to broad-based simulation tests in rapid prototyping software - Matlab/Simulink. These tests proved the advantage of multi-region fuzzy logic controller with local PID controllers over its traditional counterpart.

  4. Are autism spectrum conditions more prevalent in an information-technology region? A school-based study of three regions in the Netherlands.

    Science.gov (United States)

    Roelfsema, Martine T; Hoekstra, Rosa A; Allison, Carrie; Wheelwright, Sally; Brayne, Carol; Matthews, Fiona E; Baron-Cohen, Simon

    2012-05-01

    We tested for differences in the prevalence of autism spectrum conditions (ASC) in school-aged children in three geographical regions in the Netherlands. Schools were asked to provide the number of children enrolled, the number having a clinical diagnosis of ASC and/or two control neurodevelopmental conditions. Prevalence was evaluated by negative binomial regression and adjustments were made for non-response and size of the schools. The prevalence estimates of ASC in Eindhoven was 229 per 10,000, significantly higher than in Haarlem (84 per 10,000) and Utrecht (57 per 10,000), whilst the prevalence for the control conditions were similar in all regions. Phase two is planned to validate school-reported cases using standardized diagnostic methods and to explore the possible causes for these differences.

  5. Solid state controller three axes controller

    Science.gov (United States)

    Bailey, C. L., Jr. (Inventor)

    1973-01-01

    The reported flight controller features a handle grip which is mounted on a longitudinally extending control element. The handle grip is pivotally mounted on the control element about a pitch axis which is perpendicular to the longitudinal axis through the control element. The pivotal mounting includes a resilient force mounting mechanism which centers the grip relative to the control element. Rotation of the handle grip produces a direct rotation of a transducer element in a transducer which provides an electrical indication of the rotative movement about three mutually perpendicular axes.

  6. Experimental studies on mitigation of LOCA for a high flux research reactor

    International Nuclear Information System (INIS)

    Saxena, A.K.

    2006-01-01

    Experimental studies on the rewetting behaviour of hot vertical annular channels were performed to study the mitigation of consequences of loss of coolant accident (LOCA) for a high flux research reactor. Studies were carried out to study the rewetting behaviour with hot inner tube, for bottom flooding and top flow rewetting conditions. The tube was made of stainless steel. Experiments were conducted for water flow rates in the annulus upto 7 litres per minute (l pm) (11.7 x 10 -5 m 3 s -1 ). The initial surface temperature of the inner tube was varied from 200 to 500 degC. (author)

  7. Experimental investigation of an actively controlled three-dimensional turret wake

    Science.gov (United States)

    Shea, Patrick R.

    Hemispherical turrets are bluff bodies commonly used to house optical systems on airborne platforms. These bluff bodies develop complex, three-dimensional flow fields that introduce high mean and fluctuating loads to the turret as well as the airframe support structure which reduce the performance of both the optical systems and the aircraft. An experimental investigation of the wake of a three-dimensional, non-conformal turret was performed in a low-speed wind tunnel at Syracuse University to develop a better understanding of the fundamental flow physics associated with the turret wake. The flow field was studied at a diameter based Reynolds number of 550,000 using stereoscopic particle image velocimetry and dynamic pressure measurements both with and without active flow control. Pressure measurements were simultaneously sampled with the PIV measurements and taken on the surrounding boundary layer plate and at several locations on the turret geometry. Active flow control of the turret wake was performed around the leading edge of the turret aperture using dynamic suction in steady open-loop, unsteady open-loop, and simple closed-loop configurations. Analysis of the uncontrolled wake provided insight into the complex three-dimensional wake when evaluated spatially using PIV measurements and temporally using spectral analysis of the pressure measurements. Steady open-loop suction was found to significantly alter the spatial and temporal nature of the turret wake despite the control being applied locally to the aperture region of the turret. Unsteady open-loop and simple closed-loop control were found to provide similar levels of control to the steady open-loop forcing with a 45% reduction in the control input as calculated using the jet momentum coefficient. The data set collected provides unique information regarding the development of the baseline three-dimensional wake and the wake with three different active flow control configurations. These data can be used to

  8. Conductive polymer switch for controlling superconductivity

    International Nuclear Information System (INIS)

    McDevitt, J.T.; Haupt, S.G.; Riley, D.R.; Zhao, J.; Grassi, J.; Lo, K.; Jones, C.

    1994-01-01

    The preparation of a hybrid conducting polymer/high-temperature superconductor device consisting of a polypyrrole coated YBa 2 Cu 3 O 7-σ microbridge is reported. Electrochemical techniques are exploited to alter the oxidation state of the polymer and, in doing so, it is found for the first time that superconductivity can be modulated in a controllable and reproducible fashion by a polymer layout. Whereas the neutral (insulating) polypyrrole only slightly influences the electrical properties of the underlying YBa 2 Cu 3 O 7-σ film, the oxidized (conductive) polymer depresses T c by up to 50K. In a similar fashion, the oxidation state of the polymer is found to reversibly modulate the magnitude of J c , the superconducting critical current. Thus, a new type of molecule switch for controlling superconductivity is demonstrated

  9. THREE-VALENCE-PARTICE NUCLEI IN THE 132Sn and 208 Pb REGIONS

    International Nuclear Information System (INIS)

    Benchikh, L.; Draoui, B.; Latfaoui, M.; Aissaoui, L.

    2011-01-01

    Full text: Among the nuclei of the nuclear charter, the nuclei around closed shells play a key role in understanding the effective interaction properties between nucleons far from the valley of stability; particulary, the nuclei of a few valence nucleons around doubly magic 208 28Pb126 and 132 50Sn82 nuclei. The interest of both regions 208Pb and 132Sn lies in the fact that there is a great similarity between their nuclear spectroscopic properties. The single energy gaps in both cases are comparable and the orbitals above and below these gaps are similarly ordered. Each single state in the region of 132Sn has its counterpart in that of 208Pb. An interesting predictive consequence, the interactions of the Sn region, difficult region to reach experimentally, can be estimated from their corresponding ones constructed to describe the nuclei of the Pb region. Because of the importance of the similarity existing between the spectroscopy of these two regions, we are interested in nuclei with three valence nucleons in the lead and Tin regions on the basis of experimental data (spin, parity and energy states). In this context, the theoretical study is conducted within the shell model using the MSDI interaction for the energy spectra calculations of the studied nuclei. The calculated results are in good agreement with the available experimental data and show evidence that a close resemblance between the spectroscopy of these two regions persists when moving away from the immediate neighbours of doubly magic 132Sn and 208Pb.

  10. Biogeomorphic and pedogenic impact of trees in three soil regions

    Science.gov (United States)

    Pawlik, Łukasz; Šamonil, Pavel

    2017-04-01

    Vegetation is an important factor of soil formation which together with topography, geology, climate and time modulates chemical and physical soil characteristics. Tree/soils/regolith interaction was recognized in recently uprooted trees and relict treethrow mounds and pits. In our present study we focus on effects of individual standing trees in pedogenesis and biogeomorphic processes. Constant pressure of tree root systems, changing hydric and temperature regime, together with rhizospheric microbes and root mycorrhizal associations may cause multiscale alterations to regolith and soils. We hypothesize different soil chemical properties under old tree stumps compared to unaffected control pedon resulted from affected pedogenetical pathways at the analyzed microsites. The present project highlights changes in soil properties under tree stumps in three different soil regions: Haplic Cambisols (Turbacz Reserve, Gorce Mts., Poland, hereafter HC), Entic Podzols (Zofin Reserve, Novohradske Mts., the Czech Republic, hereafter EP), Albic Podzols (Upper Peninsula, Michigan, USA, hereafter AP). These three regions represent different degrees of soil weathering and leaching. Pedons under fir, beech and hemlock stumps, as well as unaffected control pedons were sampled and laboratory analyzed for several chemical properties; active and exchangeable soil reaction, oxidized carbon, total nitrogen, and various forms of Fe, Al, Mn and Si. At the same time we studied age of the sampled tree stumps, as well as age of their death using radiocarbon technique and dendrochronology. While no effects of the soil-trees interactions can be visible on hillslope surface, we found important evidence of biomechanical activities of tree roots (e.g. root channels) and biochemical changes which add to the discussion about biogeomorphic and pedogenic significance of trees and tree roots as drivers of biomechanical weathering and soil processes in the decadal and centennial time scales. Preliminary

  11. Multiple independent origins of mitochondrial control region duplications in the order Psittaciformes

    Science.gov (United States)

    Schirtzinger, Erin E.; Tavares, Erika S.; Gonzales, Lauren A.; Eberhard, Jessica R.; Miyaki, Cristina Y.; Sanchez, Juan J.; Hernandez, Alexis; Müeller, Heinrich; Graves, Gary R.; Fleischer, Robert C.; Wright, Timothy F.

    2012-01-01

    Mitochondrial genomes are generally thought to be under selection for compactness, due to their small size, consistent gene content, and a lack of introns or intergenic spacers. As more animal mitochondrial genomes are fully sequenced, rearrangements and partial duplications are being identified with increasing frequency, particularly in birds (Class Aves). In this study, we investigate the evolutionary history of mitochondrial control region states within the avian order Psittaciformes (parrots and cockatoos). To this aim, we reconstructed a comprehensive multi-locus phylogeny of parrots, used PCR of three diagnostic fragments to classify the mitochondrial control region state as single or duplicated, and mapped these states onto the phylogeny. We further sequenced 44 selected species to validate these inferences of control region state. Ancestral state reconstruction using a range of weighting schemes identified six independent origins of mitochondrial control region duplications within Psittaciformes. Analysis of sequence data showed that varying levels of mitochondrial gene and tRNA homology and degradation were present within a given clade exhibiting duplications. Levels of divergence between control regions within an individual varied from 0–10.9% with the differences occurring mainly between 51 and 225 nucleotides 3′ of the goose hairpin in domain I. Further investigations into the fates of duplicated mitochondrial genes, the potential costs and benefits of having a second control region, and the complex relationship between evolutionary rates, selection, and time since duplication are needed to fully explain these patterns in the mitochondrial genome. PMID:22543055

  12. Cerebral glucose metabolism in Wernicke's, Broca's, and conduction aphasia

    International Nuclear Information System (INIS)

    Metter, E.J.; Kempler, D.; Jackson, C.; Hanson, W.R.; Mazziotta, J.C.; Phelps, M.E.

    1989-01-01

    Cerebral glucose metabolism was evaluated in patients with either Wernicke's (N = 7), Broca's (N = 11), or conduction (N = 10) aphasia using 18 F-2-fluoro-2-deoxy-D-glucose with positron emission tomography. The three aphasic syndromes differed in the degree of left-to-right frontal metabolic asymmetry, with Broca's aphasia showing severe asymmetry and Wernicke's aphasia mild-to-moderate metabolic asymmetry, while patients with conduction aphasia were metabolically symmetric. On the other hand, the three syndromes showed the same degree of metabolic decline in the left temporal region. The parietal region appeared to separate conduction aphasia from both Broca's and Wernicke's aphasias. Common aphasic features in the three syndromes appear to be due to common changes in the temporal region, while unique features were associated with frontal and parietal metabolic differences

  13. Example-based illustrations of design, conduct, analysis and result interpretation of multi-regional clinical trials.

    Science.gov (United States)

    Quan, Hui; Mao, Xuezhou; Tanaka, Yoko; Binkowitz, Bruce; Li, Gang; Chen, Josh; Zhang, Ji; Zhao, Peng-Liang; Ouyang, Soo Peter; Chang, Mark

    2017-07-01

    Extensive research has been conducted in the Multi-Regional Clinical Trial (MRCT) area. To effectively apply an appropriate approach to a MRCT, we need to synthesize and understand the features of different approaches. In this paper, examples are used to illustrate considerations regarding design, conduct, analysis and interpretation of result of MRCTs. We start with a brief discussion of region definitions and the scenarios where different regions have differing requirements for a MRCT. We then compare different designs and models as well as the corresponding interpretation of the results. We highlight the importance of paying special attention to trial monitoring and conduct to prevent potential issues associated with the final trial results. Besides evaluating the overall treatment effect for the entire MRCT, we also consider other key analyses including quantification of regional treatment effects within a MRCT, and assessment of consistency of these regional treatment effects. Copyright © 2017 Elsevier Inc. All rights reserved.

  14. An analysis of hot plate initial temperature effect on rectangular narrow gap quenching process

    International Nuclear Information System (INIS)

    M-Hadi Kusuma; Mulya Juarsa; Anhar Riza Antariksawan; Nandy Putra

    2012-01-01

    The understanding about thermal management in the event of a severe accident such as the melting nuclear reactor fuel and reactor core, became a priority to maintain the integrity of reactor pressure vessel. Thus the debris will not out from the reactor pressure vessel and resulting impact of more substantial to the environment. One way to maintain the integrity of the reactor pressure vessel was cooling of the excess heat generated due to the accident. To get understanding of this aspect, there search focused on the effect of the initial temperature of the hot plate in the rectangular narrow gap quenching process. The initial temperature effect on quenching process is related to cooling process (thermal management) when the occurrence of a nuclear accident due to loss of coolant accident or severe accident. In order to address the problem, it is crucial to conduct research to get a better understanding of thermal management regarding to nuclear cooling accident. The research focused on determining the rewetting temperature of hot plate cooling on 220°C, 400°C, and 600°C with 0.2 liters/sec cooling water flowrate. Experiments were carried out by injecting 85°C cooling water temperature into the narrow gap at flowrates of 0.2 liters/sec. Data of transient temperature measurements were recorded using a data acquisition system in order to know the rewetting temperature during the quenching process. This study aims to understand the effect of hot plate initial temperature on rewetting during rectangular narrow gap quenching process. The results obtained show that the rewetting point on cooling the hot plate 220°C, 400°C and 600°occurs at varying rewetting temperatures. At 220°C hot plate initial temperature, the rewetting temperature occurs on 220°C. At 400°C hot plate initial temperature, the rewetting temperature occurs on 379.51°C. At 600°C hot plate initial temperature, the rewetting temperature occurs on 426.63°C. Significant differences of hot plate

  15. Performance of a combined three-hole conductivity probe for void fraction and velocity measurement in air-water flows

    Energy Technology Data Exchange (ETDEWEB)

    Borges, Joao Eduardo [IDMEC, Instituto Superior Tecnico, Technical University of Lisbon, Department of Mechanical Engineering, Lisbon (Portugal); Pereira, Nuno H.C. [EST Setubal, Polytechnic Institute of Setubal, Department of Mechanical Engineering, Setubal (Portugal); Matos, Jorge [Instituto Superior Tecnico, Technical University of Lisbon, Department of Civil Engineering and Architecture, Lisbon (Portugal); Frizell, Kathleen H. [U.S. Bureau of Reclamation, Denver, CO (United States)

    2010-01-15

    The development of a three-hole pressure probe with back-flushing combined with a conductivity probe, used for measuring simultaneously the magnitude and direction of the velocity vector in complex air-water flows, is described in this paper. The air-water flows envisaged in the current work are typically those occurring around the rotors of impulse hydraulic turbines (like the Pelton and Cross-Flow turbines), where the flow direction is not known prior to the data acquisition. The calibration of both the conductivity and three-hole pressure components of the combined probe in a rig built for the purpose, where the probe was placed in a position similar to that adopted for the flow measurements, will be reported. After concluding the calibration procedure, the probe was utilized in the outside region of a Cross-Flow turbine rotor. The experimental results obtained in the present study illustrate the satisfactory performance of the combined probe, and are encouraging toward its use for characterizing the velocity field of other complex air-water flows. (orig.)

  16. Performance of a combined three-hole conductivity probe for void fraction and velocity measurement in air-water flows

    Science.gov (United States)

    Borges, João Eduardo; Pereira, Nuno H. C.; Matos, Jorge; Frizell, Kathleen H.

    2010-01-01

    The development of a three-hole pressure probe with back-flushing combined with a conductivity probe, used for measuring simultaneously the magnitude and direction of the velocity vector in complex air-water flows, is described in this paper. The air-water flows envisaged in the current work are typically those occurring around the rotors of impulse hydraulic turbines (like the Pelton and Cross-Flow turbines), where the flow direction is not known prior to the data acquisition. The calibration of both the conductivity and three-hole pressure components of the combined probe in a rig built for the purpose, where the probe was placed in a position similar to that adopted for the flow measurements, will be reported. After concluding the calibration procedure, the probe was utilized in the outside region of a Cross-Flow turbine rotor. The experimental results obtained in the present study illustrate the satisfactory performance of the combined probe, and are encouraging toward its use for characterizing the velocity field of other complex air-water flows.

  17. Photo control of transport properties in a disordered wire: Average conductance, conductance statistics, and time-reversal symmetry

    International Nuclear Information System (INIS)

    Kitagawa, Takuya; Oka, Takashi; Demler, Eugene

    2012-01-01

    In this paper, we study the full conductance statistics of a disordered 1D wire under the application of light. We develop the transfer matrix method for periodically driven systems to analyze the conductance of a large system with small frequency of light, where coherent photon absorptions play an important role to determine not only the average but also the shape of conductance distributions. The average conductance under the application of light results from the competition between dynamic localization and effective dimension increase, and shows non-monotonic behavior as a function of driving amplitude. On the other hand, the shape of conductance distribution displays a crossover phenomena in the intermediate disorder strength; the application of light dramatically changes the distribution from log-normal to normal distributions. Furthermore, we propose that conductance of disordered systems can be controlled by engineering the shape, frequency and amplitude of light. Change of the shape of driving field controls the time-reversals symmetry and the disordered system shows analogous behavior as negative magneto-resistance known in static weak localization. A small change of frequency and amplitude of light leads to a large change of conductance, displaying giant opto-response. Our work advances the perspective to control the mean as well as the full conductance statistics by coherently driving disordered systems. - Highlights: ► We study conductance of disordered systems under the application of light. ► Full conductance distributions are obtained. ► A transfer matrix method is developed for driven systems. ► Conductances are dramatically modified upon the application of light. ► Time-reversal symmetry can also be controlled by light application.

  18. Magnetic-field-controlled negative differential conductance in scanning tunneling spectroscopy of graphene npn junction resonators

    Science.gov (United States)

    Li, Si-Yu; Liu, Haiwen; Qiao, Jia-Bin; Jiang, Hua; He, Lin

    2018-03-01

    Negative differential conductance (NDC), characterized by the decreasing current with increasing voltage, has attracted continuous attention for its various novel applications. The NDC typically exists in a certain range of bias voltages for a selected system and controlling the regions of NDC in curves of current versus voltage (I -V ) is experimentally challenging. Here, we demonstrate a magnetic-field-controlled NDC in scanning tunneling spectroscopy of graphene npn junction resonators. The magnetic field not only can switch on and off the NDC, but also can continuously tune the regions of the NDC in the I -V curves. In the graphene npn junction resonators, magnetic fields generate sharp and pronounced Landau-level peaks with the help of the Klein tunneling of massless Dirac fermions. A tip of scanning tunneling microscope induces a relatively shift of the Landau levels in graphene beneath the tip. Tunneling between the misaligned Landau levels results in the magnetic-field-controlled NDC.

  19. Regional groundwater characteristics and hydraulic conductivity based on geological units in Korean peninsula

    Science.gov (United States)

    Kim, Y.; Suk, H.

    2011-12-01

    In this study, about 2,000 deep observation wells, stream and/or river distribution, and river's density were analyzed to identify regional groundwater flow trend, based on the regional groundwater survey of four major river watersheds including Geum river, Han river, Youngsan-Seomjin river, and Nakdong river in Korea. Hydrogeologial data were collected to analyze regional groundwater flow characteristics according to geological units. Additionally, hydrological soil type data were collected to estimate direct runoff through SCS-CN method. Temperature and precipitation data were used to quantify infiltration rate. The temperature and precipitation data were also used to quantify evaporation by Thornthwaite method and to evaluate groundwater recharge, respectively. Understanding the regional groundwater characteristics requires the database of groundwater flow parameters, but most hydrogeological data include limited information such as groundwater level and well configuration. In this study, therefore, groundwater flow parameters such as hydraulic conductivities or transmissivities were estimated using observed groundwater level by inverse model, namely PEST (Non-linear Parameter ESTimation). Since groundwater modeling studies have some uncertainties in data collection, conceptualization, and model results, model calibration should be performed. The calibration may be manually performed by changing parameters step by step, or various parameters are simultaneously changed by automatic procedure using PEST program. In this study, both manual and automatic procedures were employed to calibrate and estimate hydraulic parameter distributions. In summary, regional groundwater survey data obtained from four major river watersheds and various data of hydrology, meteorology, geology, soil, and topography in Korea were used to estimate hydraulic conductivities using PEST program. Especially, in order to estimate hydraulic conductivity effectively, it is important to perform

  20. Three-component homeostasis control

    Science.gov (United States)

    Xu, Jin; Hong, Hyunsuk; Jo, Junghyo

    2014-03-01

    Two reciprocal components seem to be sufficient to maintain a control variable constant. However, pancreatic islets adapt three components to control glucose homeostasis. They are α (secreting glucagon), β (insulin), and δ (somatostatin) cells. Glucagon and insulin are the reciprocal hormones for increasing and decreasing blood glucose levels, while the role of somatostatin is unknown. However, it has been known how each hormone affects other cell types. Based on the pulsatile hormone secretion and the cellular interactions, this system can be described as coupled oscillators. In particular, we used the Landau-Stuart model to consider both amplitudes and phases of hormone oscillations. We found that the presence of the third component, δ cell, was effective to resist under glucose perturbations, and to quickly return to the normal glucose level once perturbed. Our analysis suggested that three components are necessary for advanced homeostasis control.

  1. Ecosystem respiration, methane and nitrous oxide fluxes from ecotopes in a rewetted extracted peatland in Sweden

    Directory of Open Access Journals (Sweden)

    S. Jordan

    2016-09-01

    Full Text Available Ecosystem respiration (carbon dioxide; CO2, methane (CH4 and nitrous oxide (N2O fluxes to the atmosphere were determined using an opaque closed chamber method within various ecotopes (vegetation covered, bare peat and open water in a rewetted extracted peatland and within an adjacent open poor fen in Sweden. Ecotopes had a significant impact on CO2 and CH4 fluxes to the atmosphere. Ecosystem respiration and CH4 emissions from the bare peat site, the constructed shallow lake and the open poor fen were low but were much higher from ecotopes with Eriophorum vaginatum tussocks and Eriophorum angustifolium. A combination of vascular plant cover and high soil temperatures enhanced ecosystem respiration, while a combination of vascular plant cover, high water table levels and high soil temperatures enhanced CH4 emissions. N2O emissions contributed little to total greenhouse gas (GHG fluxes from the soil-plant-water systems to the atmosphere. However, the overall climate impact of CH4 emissions from the study area did not exceed the impact of soil and plant respiration. With regard to management of extracted peatlands, the construction of a nutrient-poor shallow lake showed great potential for lowering GHG fluxes to the atmosphere.

  2. A rubella serosurvey in postpartum women in the three regions of Peru.

    Science.gov (United States)

    Suárez-Ognio, Luis; Adrianzén, Ana; Ortiz, Ana; Martínez, Carlos; Whittembury, Alvaro; Cabezudo, Edwin; de Oliveira, Lucia; Siqueira, Marilda M; Castillo-Solórzano, Carlos

    2007-08-01

    To determine the proportion of postpartum women aged 15-49 in Peru who are susceptible to rubella, in order to help address strategies to eliminate rubella and to prevent congenital rubella syndrome (CRS) in the country. A cross-sectional survey was conducted during March and April 2003 in six main regional hospitals, in the three geographic regions (coast, mountain, and jungle) of Peru. For the postpartum women who provided written informed consent, a questionnaire was administered and a blood specimen was collected. Sera were tested for rubella immunoglobulin G (IgG) antibody, using a commercial enzyme-linked immunosorbent serologic assay (ELISA) kit. Univariate, bivariate, and multivariate analyses were carried out to assess risk factors for susceptibility. In total, 1 236 postpartum women were enrolled. The overall proportion of IgG-antibody negative women was 12.8% (95% confidence interval (CI): 10.9%-14.6%). Bivariate analysis found the following variables associated with susceptibility: living in the jungle region (odds ratio (OR) = 1.65; 95% CI: 1.13-2.42); age jungle region (OR = 1.67; 95% CI: 1.13-2.46); age Peru among the countries facing a moderate level of risk for the occurrence of CRS cases. The findings suggest the need to also provide the rubella vaccine to other population groups, especially women of childbearing age.

  3. The neurobiology of oppositional defiant disorder and conduct disorder: altered functioning in three mental domains.

    Science.gov (United States)

    Matthys, Walter; Vanderschuren, Louk J M J; Schutter, Dennis J L G

    2013-02-01

    This review discusses neurobiological studies of oppositional defiant disorder and conduct disorder within the conceptual framework of three interrelated mental domains: punishment processing, reward processing, and cognitive control. First, impaired fear conditioning, reduced cortisol reactivity to stress, amygdala hyporeactivity to negative stimuli, and altered serotonin and noradrenaline neurotransmission suggest low punishment sensitivity, which may compromise the ability of children and adolescents to make associations between inappropriate behaviors and forthcoming punishments. Second, sympathetic nervous system hyporeactivity to incentives, low basal heart rate associated with sensation seeking, orbitofrontal cortex hyporeactiviy to reward, and altered dopamine functioning suggest a hyposensitivity to reward. The associated unpleasant emotional state may make children and adolescents prone to sensation-seeking behavior such as rule breaking, delinquency, and substance abuse. Third, impairments in executive functions, especially when motivational factors are involved, as well as structural deficits and impaired functioning of the paralimbic system encompassing the orbitofrontal and cingulate cortex, suggest impaired cognitive control over emotional behavior. In the discussion we argue that more insight into the neurobiology of oppositional defiance disorder and conduct disorder may be obtained by studying these disorders separately and by paying attention to the heterogeneity of symptoms within each disorder.

  4. Evaluation of regional climate simulations over the Great Lakes region driven by three global data sets

    Science.gov (United States)

    Shiyuan Zhong; Xiuping Li; Xindi Bian; Warren E. Heilman; L. Ruby Leung; William I. Jr. Gustafson

    2012-01-01

    The performance of regional climate simulations is evaluated for the Great Lakes region. Three 10-year (1990-1999) current-climate simulations are performed using the MM5 regional climate model (RCM) with 36-km horizontal resolution. The simulations employed identical configuration and physical parameterizations, but different lateral boundary conditions and sea-...

  5. Factors associated with childhood ocular morbidity and blindness in three ecological regions of Nepal: Nepal pediatric ocular disease study.

    Science.gov (United States)

    Adhikari, Srijana; Shrestha, Mohan Krishna; Adhikari, Kamala; Maharjan, Nhukesh; Shrestha, Ujjowala Devi

    2014-10-23

    Nepal Pediatric Ocular Diseases Study is a three year longitudinal population based study. Here we present the baseline survey report which aims to investigate various risk factors associated with childhood ocular morbidity and blindness in three ecological regions of Nepal. This baseline survey is a population based cross sectional study. The investigation was conducted in a district from each of the following regions: Terai, Hill and Mountain. The Village Development Committees (VDCs) from each district were selected by random sampling. Three Community health workers were given training on vision screening and identification of abnormal ocular signs in children. They conducted a house to house survey in their respected districts examining the children and gathering a standardized set of data variables. Children with abnormal vision or ocular signs were then further examined by pediatric ophthalmologists. A total of 10950 children aged 0-10 years (5403 from Terai, 3204 from the hills, 2343 from the mountains) were enrolled in the study. However 681 (6.2%) were non responders. The male to female ratio was 1.03. The overall prevalence of ocular morbidity was 3.7% (95% CI of 3.4%-4%) and blindness was 0.07% (95% CI of 0.02%-0.12%). Ocular morbidity was more prevalent in the mountain region whereas blindness was more prevalent in the Terai region.Children from the Terai region were more likely to suffer from congenital ocular anomalies compared to the other regions. Children whose mother smoked, drank alcohol, or was illiterate were significantly afflicted with ocular diseases (p Blindness was more prevalent in children who suffered from a systemic illness. Females and under-nourished children were more likely to have ocular morbidity and blindness. It was found that childhood blindness was more prevalent in the Terai region, the undernourished, females and in those with co-morbid systemic illnesses. This study strongly suggests that prevention of childhood

  6. 40 CFR 81.112 - Charleston Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Regions § 81.112 Charleston Intrastate Air Quality Control Region. The Charleston Intrastate Air Quality Control Region (South Carolina) consists of the territorial area encompassed by the... Quality Control Region: Region 1. 81.107Greenwood Intrastate Air Quality Control Region: Region 2. 81...

  7. Sulfur and carbon isotope biogeochemistry of a rewetted brackish fen

    Science.gov (United States)

    Koebsch, Franziska; Gehre, Matthias; Winkel, Matthias; Koehler, Stefan; Koch, Marian; Jurasinski, Gerald; Spitzy, Alejandro; Liebner, Susanne; Sachs, Torsten; Schmiedinger, Iris; Kretzschmann, Lisett; Saborowski, Anke; Böttcher, Michael E.

    2015-04-01

    Coastal wetlands are at the interface between terrestrial freshwater and marine and exhibit very specific biogeochemical conditions. Intermittent sea water intrusion affects metabolic pathways, i. e. anaerobic carbon metabolism is progressively dominated by sulfate reduction with lower contribution of methanogenesis whilst methane production is increasingly shifted from acetoclastic to hydrogenotrophic. Due to expanding anthropogenic impact a large proportion of coastal ecosystems is degraded with severe implications for the biogeochemical processes. We use concentration patterns and stable isotope signatures of water, sulfate, dissolved carbonate, and methane (δ2H, δ13C, δ18O, δ34S) to investigate the S and C metabolic cycle in a rewetted fen close to the southern Baltic Sea border. Such studies are crucial to better predict dynamic ecosystem feedback to global change like organic matter (OM) decomposition or greenhouse gas emissions. Yet, little is known about the metabolic pathways in such environments. The study site is part of the TERENO Observatory "Northeastern German Lowlands' and measurements of methane emissions have run since 2009. High methane fluxes up to 800 mg m-2 hr-1 indicate that methanogenesis is the dominant C metabolism pathway despite of high sulfate concentrations (up to 37 mM). The presented data are part of a comprehensive biogeochemical investigation that we conducted in autumn 2014 and that comprises 4 pore water profiles and sediment samples within a transect of 300-1500 m distance to the Baltic Sea. Depth of organic layers ranged from 25 to 140 cm with high OM contents (up to 90 dwt.%). Sulfate/chloride ratios in the pore waters were lower than in the Baltic Sea for most sites and sediment depths indicated a substantial net sulfate loss. Sulfide concentrations were negligible at the top and increased parallel to the sulfate concentrations with depth to values of up to 0.3 mM. One pore water profiles situated 1150 m from the Baltic

  8. Controlling thermal chaos in the mantle by positive feedback from radiative thermal conductivity

    Directory of Open Access Journals (Sweden)

    F. Dubuffet

    2002-01-01

    influence and help to control thermal chaos developed in the deep mantle. These results have been verified to exist also in three-dimensional geometry and would argue for the need to consider the potentially important role played by radiative thermal conductivity in controlling chaotic flows in time-dependent mantle convection, the mantle heat transfer, the number of hotspots and the attendant mixing of geochemical anomalies.

  9. Direct numerical reconstruction of conductivities in three dimensions using scattering transforms

    DEFF Research Database (Denmark)

    Bikowski, Jutta; Knudsen, Kim; Mueller, Jennifer L

    2011-01-01

    A direct three-dimensional EIT reconstruction algorithm based on complex geometrical optics solutions and a nonlinear scattering transform is presented and implemented for spherically symmetric conductivity distributions. The scattering transform is computed both with a Born approximation and from...

  10. ANALISA PENGARUH SUHU AWAL PELAT PANAS PADA PROSES QUENCHING CELAH SEMPIT REKTANGULAR

    Directory of Open Access Journals (Sweden)

    M. Hadi Kusuma

    2015-03-01

    melewati celah sempit, perubahan nilai kalor spesifik bahan, perubahan nilai konduktifitas termal, dan perbedaan suhu wall superheated-nya. Perubahan-perubahan yang terjadi tersebut menyebabkan peningkatan suhu rewetting seiring dengan kenaikan suhu awal pelat panas. Kata kunci: rewetting, quenching, celah sempit, keselamatan nuklir   The understanding about thermal management in the event of a severe accident such as the melting nuclear reactor fuel and reactor core, became a priority to maintain the integrity of reactor pressure vessel. Thus the debris will not out from the reactor pressure vessel and resulting impact of more substantial to the environment. One way to maintain the integrity of the reactor pressure vessel was cooling of the excess heat generated due to the accident. Toget understanding of this aspect, the research focused on the effect of the initial temperature of the hot plate in the rectangular narrow gap quenching process. The initial temperature effect on quenching process is related to cooling process (thermal management when the occurrence of a nuclear accident due to loss of coolant accident or severe accident. In order to address the problem, it is crucial to conduct research to get a better understanding of thermal management regarding to nuclear cooling accident. The research focused on determining the rewetting temperature of hot plate cooling on 220 0C, 400 0C, and 600 0C with 0.2 liters/sec cooling water flowrate. Experiments were carried out by injecting 85 0C cooling water temperature into the narrow gap at flowrates of 0.2 liters/sec. Data of transient temperature measurements were recorded using a data acquisition system in order to know the rewetting temperature during the quenching process. This study aims to understand the effect of hot plate intial temperature on rewetting during rectangular narrow gap quenching process. The results obtained show that the rewetting point on cooling the hot plate 220 0C, 400 0C and 600 0C occurs at

  11. Behavior of introduced regional clones of Theobroma cacao toward the infection Moniliophthora roreri in three different regions of Colombia

    Directory of Open Access Journals (Sweden)

    Jaimes Yeirme

    2011-08-01

    Full Text Available

    Moniliasis (frosty pod rot, caused by Moniliophthora roreri, is the most limiting disease of cacao bean production in Colombia. Disease control has focused primarily on the implementation of cultural methods, which are inefficient and increase costs of production. A promising alternative for the control of M. roreri is the genetic approach, involving the search for plants with known resistance in the field. The aim of this study was to evaluate the behavior of 13 regional clones of Corpoica Selection Colombia (SCC, ten regional Fedecacao clones (with the initial F, three clones Caucasia (CAU and 13 introduced clones for resistance to M. roreri, by monitoring symptoms and signs of the pathogen in fruits of the cacao at three experimental sites located in Arauquita (Arauca, San Vicente and Rionegro (Santander. To estimate the degree of susceptibility or resistance of each clone, the pathogen was inoculated into fruits 75-5 days old. Eight weeks later, the variables Incidence, Internal Severity Index and External Severity Index were evaluated. In the three experimental sites, the ICS clone 95 behaved as a resistant plant with ISI ranging from 1.4 to 1.9. In the other clones tested, susceptibility varied according to altitude and environmental conditions. However, the ICS clone 95 showed partial resistance, varying the spread of the pathogen in the plant tissue.

  12. Severe and uncomplicated falciparum malaria in children from three regions and three ethnic groups in Cameroon: prospective study

    Directory of Open Access Journals (Sweden)

    Achidi Eric A

    2012-06-01

    Full Text Available Abstract Background To identify the factors that account for differences in clinical outcomes of malaria as well as its relationship with ethnicity, transmission intensity and parasite density. Methods A prospective study was conducted in nine health facilities in the Centre, Littoral and South West regions of Cameroon, and in three ethnic groups; the Bantu, Semi-Bantu and Foulbe. Children aged one month to 13 years, with diagnosis suggestive of malaria, were recruited and characterized using the WHO definition for severe and uncomplicated malaria. Malaria parasitaemia was determined by light microscopy, haematological analysis using an automated haematology analyser and glucose level by colorimetric technique. Results Of the febrile children screened, 971 of the febrile children screened fulfilled the inclusion criteria for specific malaria clinical phenotypes. Forty-nine (9.2% children had cerebral malaria, a feature that was similar across age groups, ethnicity and gender but lower (P P P = 0.009 and Foulbe (P = 0.026 counterparts in the Centre region. The overall study case fatality was 4.8 (47/755, with cerebral malaria being the only significant risk factor associated with death. Severe anaemia, though a common and major clinical presentation, was not significantly associated with risk of death. Conclusion About half of the acutely febrile children presented with severe malaria, the majority being cases of severe malaria anaemia, followed by respiratory distress and cerebral malaria. The latter two were less prevalent in the Centre region compared to the other regions. Cerebral malaria and hyperpyrexia were the only significant risk factors associated with death.

  13. Control of Surface Attack by Gallium Alloys in Electrical Contacts.

    Science.gov (United States)

    1986-03-28

    and atmospheric control but does not allow visual observation of the contact brushes. This machine is a small homopolar motor built from mild steel...collectors,gallium, homopolar devices,liquid metals,~- is. ABSTRACT ICNI.. .. w 41N"w -~dv.mp.d Wrllt by Itabata" * Electrical contact between a copp’er...32 5 Test rig with felt metal brushes 32 6 Homopolar test apparatus 33 7 Rewetting of alloy track 33 8 Alloy track after running with finger 34 brushes

  14. Auroral zone E-region conductivities during solar minimum derived from EISCAT data

    International Nuclear Information System (INIS)

    Schlegel, K.

    1988-01-01

    From two years of EISCAT data (1985-1986, a period of low solar activity) 8337 E-region conductivity profiles have been calculated as 5-min averages. From these profiles the height of the conductivity maxima for the Hall and Pedersen conductivities (H max ), the height-integrated Hall and Pedersen conductivities and the ratio of both have been computed. Histograms as well as average values of these quantities are displayed as a function of K p and of magnetic local time. The former results showed quantitatively the increase of the conductivities and the decrease of H max with increasing magnetic activity. The latter results revealed that on the average the conductivities are maximal in the early morning hours due to hard particle precipitation, H max being affected both by the solar zenith angle and by particle precipitation. The solar zenith angle dependence of the conductivities is only significant for low K p -values. Latitudinal profiles of the height-integrated conductivities show quantitatively the southward shift of the average conductivity maximum with increasing magnetic activity

  15. Fotossíntese e potencial hídrico foliar de plantas jovens de andiroba submetidas à deficiência hídrica e à reidratação Photosynthesis and water potential of andiroba seedlings submitted to water stress and rewetting

    Directory of Open Access Journals (Sweden)

    José Francisco de Carvalho Gonçalves

    2009-01-01

    experiment. Net photosynthesis, stomatal conductance, and transpiration rates were reduced by 88, 89, and 89%, respectively, after 21 days of water stress. In relation to chlorophyll a, fluorescence variables were reduced 27 to 58%. The plant water potential was reduced more than four times by 21 days of stress. With rewetting, seedlings recovered their photosynthetic characteristics in four to eight days as well as their water potential, indicating that young andiroba plants exhibited high physiological plasticity to water stress.

  16. Theoretical studies of the influence of filler material gas gap and cladding material on rewetting rate of nuclear reactor fuel pins

    International Nuclear Information System (INIS)

    Blackburn, D.; Pearson, K.G.; Shires, G.L.

    1977-03-01

    Theoretical studies of the effect of fuel and gas gap on the rewetting rate of overheated fuel pins quenched by a falling film of water are presented. Two approaches have been made: a finite difference technique and an approximate analytical solution. The results obtained by the two methods for the case of a uranium-dioxide-filled Zircaloy clad fuel pin are in close agreement. The paper shows that under high pressure conditions the delaying effect of the stored heat within the fuel on the wetting rate is relatively small, particularly if a gas gap is present between the clad and the fuel. At low pressure conditions, however, the effect of the fuel may be very important. Simplification of the analytical solution shows that at low wetting rates a constant fractional reduction in wetting speed may be anticipated the magnitude of which depends only on the relative thermal diffusivities and heat capacities of the fuel and cladding. (author)

  17. Resonator controller for the super-conducting LINAC

    International Nuclear Information System (INIS)

    Joshi, Gopal; Sujo, C.I.; Karande, Jitendra

    2001-01-01

    A resonator controller has been developed at Electronics Division, BARC, to stabilize the amplitude and phase of RF fields in the super-conducting resonators of BARC-TIFR linac. Due to reduced losses these resonators have intrinsic bandwidth of the order of one hertz at 150MHz whereas the vibration induced center frequency changes are of the order of a few hertz. In the control strategy followed the resonator is made the frequency selective part of an oscillator. The phase lock is achieved by dynamically adding a phase shift in the oscillator. In this paper we present the control strategy, implementation details and performance obtained with this controller. (author)

  18. Optical conductivity of three and two dimensional topological nodal-line semimetals

    Science.gov (United States)

    Barati, Shahin; Abedinpour, Saeed H.

    2017-10-01

    The peculiar shape of the Fermi surface of topological nodal-line semimetals at low carrier concentrations results in their unusual optical and transport properties. We analytically investigate the linear optical responses of three- and two-dimensional nodal-line semimetals using the Kubo formula. The optical conductivity of a three-dimensional nodal-line semimetal is anisotropic. Along the axial direction (i.e., the direction perpendicular to the nodal-ring plane), the Drude weight has a linear dependence on the chemical potential at both low and high carrier dopings. For the radial direction (i.e., the direction parallel to the nodal-ring plane), this dependence changes from linear into quadratic in the transition from low into high carrier concentration. The interband contribution into optical conductivity is also anisotropic. In particular, at large frequencies, it saturates to a constant value for the axial direction and linearly increases with frequency along the radial direction. In two-dimensional nodal-line semimetals, no interband optical transition could be induced and the only contribution to the optical conductivity arises from the intraband excitations. The corresponding Drude weight is independent of the carrier density at low carrier concentrations and linearly increases with chemical potential at high carrier doping.

  19. Economic implications of three strategies for the control of taeniasis

    OpenAIRE

    Alexander, A.; John, K. R.; Jayaraman, T.; Oommen, A.; Venkata Raghava, M.; Dorny, P.; Rajshekhar, V.

    2011-01-01

    Objective To evaluate the cost-effectiveness of three strategies for the control of taeniasis in a community, in terms of cost per case treated. Methods A study was conducted in South India to determine the prevalence of taeniasis by screening stool samples from 653 randomly chosen subjects, for coproantigens. The costs incurred in the project were used to estimate the cost per case screened and treated. A one-way sensitivity analysis was carried out for varying rates of taeniasis, different ...

  20. Antimicrobial Resistance Control Strategies: A Coordinated Research Initiative Experience in the Asia Pacific Region.

    Science.gov (United States)

    Lapierre, Lisette; Asenjo, Gabriela; Vergara, Constanza; Cornejo, Javiera

    2017-05-01

    The objective was to gather information on the status of antimicrobial surveillance in the Asia Pacific region and suggest control strategies. Twenty-one economies of the Asia Pacific region participated in this initiative. A survey was conducted on antimicrobial use and surveillance throughout the region. A workshop was carried out to create awareness about the issue and discuss the implementation of control strategies. Based on the survey results and workshop conclusions, it can be established that there is better understanding of the implications of antimicrobial resistance in the human medicine area. Only few economies take actions to control antimicrobial resistance on a veterinary/agricultural level. To confront antimicrobial resistance, it is critical to raise awareness; cooperation between all countries is needed to apply international standards, to be able to have harmonized public policies. Countries must align and improve their systems for surveillance and monitoring of antimicrobial resistance in human, animals, and the environment.

  1. Controlled Aloin Release from Crosslinked Polyacrylamide Hydrogels: Effects of Mesh Size, Electric Field Strength and a Conductive Polymer

    Directory of Open Access Journals (Sweden)

    Anuvat Sirivat

    2013-10-01

    Full Text Available The aim of this paper is to investigate the effects of hydrogel mesh size, a conductive polymer, and electric field strength on controlled drug delivery phenomena using drug-loaded polyacrylamide hydrogels prepared at various crosslinking ratios both with and without a conductive polymer system. Poly(p-phenylene vinylene, PPV, as the model conductive polymer, was used to study its ability to control aloin released from aloin-doped poly(p-phenylene vinylene/polyacrylamide hydrogel (aloin-doped PPV/PAAM. In the passive release, the diffusion of aloin from five aloin-doped PPV/PAAM hydrogel systems each was delayed ranging from during the first three hours to during the first 14 h due to the ionic interaction between the anionic drug and PPV. After the delayed periods, aloin could diffuse continuously into the buffer solution through the PAAM matrix. The amount of aloin released from the aloin-doped PPV/PAAM rose with increasing electric field strength as a result of the three mechanisms: the expansion of PPV chains inside the hydrogel, iontophoresis, and the electroporation of the matrix pore size, combined. Furthermore, the conductive polymer and the electric field could be used in combination to regulate the amount of release drug to a desired level, to control the release rate, and to switch the drug delivery on/off.

  2. 40 CFR 81.88 - Billings Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Regions § 81.88 Billings Intrastate Air Quality Control Region. The Metropolitan Billings Intrastate Air Quality Control Region (Montana) has been renamed the Billings Intrastate Air Quality Control... to by Montana authorities as follows: Sec. 481.168Great Falls Intrastate Air Quality Control Region...

  3. Altered spontaneous brain activity in adolescent boys with pure conduct disorder revealed by regional homogeneity analysis.

    Science.gov (United States)

    Wu, Qiong; Zhang, Xiaocui; Dong, Daifeng; Wang, Xiang; Yao, Shuqiao

    2017-07-01

    Functional magnetic resonance imaging (fMRI) studies have revealed abnormal neural activity in several brain regions of adolescents with conduct disorder (CD) performing various tasks. However, little is known about the spontaneous neural activity in people with CD in a resting state. The aims of this study were to investigate CD-associated regional activity abnormalities and to explore the relationship between behavioral impulsivity and regional activity abnormalities. Resting-state fMRI (rs-fMRI) scans were administered to 28 adolescents with CD and 28 age-, gender-, and IQ-matched healthy controls (HCs). The rs-fMRI data were subjected to regional homogeneity (ReHo) analysis. ReHo can demonstrate the temporal synchrony of regional blood oxygen level-dependent signals and reflect the coordination of local neuronal activity facilitating similar goals or representations. Compared to HCs, the CD group showed increased ReHo bilaterally in the insula as well as decreased ReHo in the right inferior parietal lobule, right middle temporal gyrus and right fusiform gyrus, left anterior cerebellum anterior, and right posterior cerebellum. In the CD group, mean ReHo values in the left and the right insula correlated positively with Barratt Impulsivity Scale (BIS) total scores. The results suggest that CD is associated with abnormal intrinsic brain activity, mainly in the cerebellum and temporal-parietal-limbic cortices, regions that are related to emotional and cognitive processing. BIS scores in adolescents with CD may reflect severity of abnormal neuronal synchronization in the insula.

  4. Community Violence Exposure and Conduct Problems in Children and Adolescents with Conduct Disorder and Healthy Controls.

    Science.gov (United States)

    Kersten, Linda; Vriends, Noortje; Steppan, Martin; Raschle, Nora M; Praetzlich, Martin; Oldenhof, Helena; Vermeiren, Robert; Jansen, Lucres; Ackermann, Katharina; Bernhard, Anka; Martinelli, Anne; Gonzalez-Madruga, Karen; Puzzo, Ignazio; Wells, Amy; Rogers, Jack C; Clanton, Roberta; Baker, Rosalind H; Grisley, Liam; Baumann, Sarah; Gundlach, Malou; Kohls, Gregor; Gonzalez-Torres, Miguel A; Sesma-Pardo, Eva; Dochnal, Roberta; Lazaratou, Helen; Kalogerakis, Zacharias; Bigorra Gualba, Aitana; Smaragdi, Areti; Siklósi, Réka; Dikeos, Dimitris; Hervás, Amaia; Fernández-Rivas, Aranzazu; De Brito, Stephane A; Konrad, Kerstin; Herpertz-Dahlmann, Beate; Fairchild, Graeme; Freitag, Christine M; Popma, Arne; Kieser, Meinhard; Stadler, Christina

    2017-01-01

    Exposure to community violence through witnessing or being directly victimized has been associated with conduct problems in a range of studies. However, the relationship between community violence exposure (CVE) and conduct problems has never been studied separately in healthy individuals and individuals with conduct disorder (CD). Therefore, it is not clear whether the association between CVE and conduct problems is due to confounding factors, because those with high conduct problems also tend to live in more violent neighborhoods, i.e., an ecological fallacy. Hence, the aim of the present study was: (1) to investigate whether the association between recent CVE and current conduct problems holds true for healthy controls as well as adolescents with a diagnosis of CD; (2) to examine whether the association is stable in both groups when including effects of aggression subtypes (proactive/reactive aggression), age, gender, site and socioeconomic status (SES); and (3) to test whether proactive or reactive aggression mediate the link between CVE and conduct problems. Data from 1178 children and adolescents (62% female; 44% CD) aged between 9 years and 18 years from seven European countries were analyzed. Conduct problems were assessed using the Kiddie-Schedule of Affective Disorders and Schizophrenia diagnostic interview. Information about CVE and aggression subtypes was obtained using self-report questionnaires (Social and Health Assessment and Reactive-Proactive aggression Questionnaire (RPQ), respectively). The association between witnessing community violence and conduct problems was significant in both groups (adolescents with CD and healthy controls). The association was also stable after examining the mediating effects of aggression subtypes while including moderating effects of age, gender and SES and controlling for effects of site in both groups. There were no clear differences between the groups in the strength of the association between witnessing violence

  5. Community Violence Exposure and Conduct Problems in Children and Adolescents with Conduct Disorder and Healthy Controls

    Directory of Open Access Journals (Sweden)

    Linda Kersten

    2017-11-01

    Full Text Available Exposure to community violence through witnessing or being directly victimized has been associated with conduct problems in a range of studies. However, the relationship between community violence exposure (CVE and conduct problems has never been studied separately in healthy individuals and individuals with conduct disorder (CD. Therefore, it is not clear whether the association between CVE and conduct problems is due to confounding factors, because those with high conduct problems also tend to live in more violent neighborhoods, i.e., an ecological fallacy. Hence, the aim of the present study was: (1 to investigate whether the association between recent CVE and current conduct problems holds true for healthy controls as well as adolescents with a diagnosis of CD; (2 to examine whether the association is stable in both groups when including effects of aggression subtypes (proactive/reactive aggression, age, gender, site and socioeconomic status (SES; and (3 to test whether proactive or reactive aggression mediate the link between CVE and conduct problems. Data from 1178 children and adolescents (62% female; 44% CD aged between 9 years and 18 years from seven European countries were analyzed. Conduct problems were assessed using the Kiddie-Schedule of Affective Disorders and Schizophrenia diagnostic interview. Information about CVE and aggression subtypes was obtained using self-report questionnaires (Social and Health Assessment and Reactive-Proactive aggression Questionnaire (RPQ, respectively. The association between witnessing community violence and conduct problems was significant in both groups (adolescents with CD and healthy controls. The association was also stable after examining the mediating effects of aggression subtypes while including moderating effects of age, gender and SES and controlling for effects of site in both groups. There were no clear differences between the groups in the strength of the association between witnessing

  6. A three-region model for tracking a two-phase mixture water level in the micro-simulator

    International Nuclear Information System (INIS)

    Seok, Ho

    1994-02-01

    -site transient analysis, and engineering studies. The present simulator consists of three functional modules: plant module, graphic module, and man-machine interaction module. The plant module includes models for core kinetics, reactor coolant system, steam generator, main steam line, BOP, and control and protection system. Each of the model is optimized to obtain the capability of real-time simulation. For simulating the thermal-hydraulic behavior of reactor coolant system in the plant module, FISA-2/WS (Fully-Implicit Safety Analysis-2/WorkStation) is developed, which adopts an implicit algorithms for their inherent stability and efficiency in solving the stiff set of equations resulted from component models. It allows the use of a larger time-step than the Courant limit without any numerical instability, and it also guarantees reasonable accuracy. And the level tracking logic and the peak cladding temperature calculation model on the basis of the simple analytical model are used to track the two-phase water level in the core and to predict the cladding temperature in the uncovered region of the core under accidents, respectively. The graphic module is designed to provide the user with more information at a glance by dynamically displaying schematic diagrams of the systems, symbols indicating the operating status of each component, trend curves, and the main control room. Especially, the CONTROL ROOM menu is designed to enable user to perform his specific actions through the schematic diagrams of the main control panels in the similar way in which operators do them in the main control room for the KO-RI nuclear power plant unit 2. In each schematic diagram of 5 sections the indicators and alarms display the various operating parameter, alarm signals, and trip signals, and the user can control the various components by operating the corresponding switches in each section through the mouse. Also, user can initiate his actions through various system diagrams. As tools for the man

  7. 40 CFR 81.51 - Portland Interstate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Regions § 81.51 Portland Interstate Air Quality Control Region. The Portland Interstate Air Quality Control Region (Oregon-Washington) has been revised to consist of the territorial area... Portland Interstate Air Quality Control Region (Oregon-Washington) will be referred to by Washington...

  8. Wood density and anatomy of three Eucalyptus species: implications for hydraulic conductivity

    OpenAIRE

    Antonio J. Barotto; Silvia Monteoliva; Javier Gyenge; Alejandro Martínez-Meier; Karen Moreno; Natalia Tesón; María Elena Fernández

    2017-01-01

    Aim of the study: To characterize wood anatomical traits of three Eucalyptus species that differ in wood density and ecological requirements, and to examine the relationships between some anatomical features, wood density, and theoretical xylem hydraulic conductivity (Ks). Area of study: We analyzed 86 trees from three sites of Argentina (Entre Ríos and Buenos Aires Provinces). Methods: The sampled trees were Eucalyptus globulus, E. grandis and E. viminalis ranging from 11 to 15 years...

  9. 40 CFR 81.36 - Maricopa Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Regions § 81.36 Maricopa Intrastate Air Quality Control Region. The Phoenix-Tucson Intrastate Air Quality Control Region has been renamed the Maricopa Intrastate Air Quality Control Region... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Maricopa Intrastate Air Quality...

  10. Measurement of in-situ hydraulic conductivity in the Cretaceous Pierre Shale

    International Nuclear Information System (INIS)

    Neuzil, C.E.; Bredehoeft, J.D.

    1981-01-01

    A recent study of the hydrology of the Cretaceous Pierre Shale utilized three techniques for measuring the hydraulic conductivity of tight materials. Regional hydraulic conductivity was obtained from a hydrodynamic model analysis of the aquifer-aquitard system which includes the Pierre Shale. Laboratory values were obtained from consolidation tests on core samples. In-situ values of hydraulic conductivity were obtained by using a borehole slug test designed specifically for tight formations. The test is conducted by isolating a portion of the borehole with one or two packers, abruptly pressurizing the shut-in portion, and recording the pressure decay with time. The test utilizes the analytical solution for pressure decay as water flows into the surrounding formation. Consistent results were obtained using the test on three successively smaller portions of a borehole in the Pierre Shale. The in-situ tests and laboratory tests yielded comparable values; the regional hydraulic conductivity was two to three orders of magnitude larger. This suggests that the lower values represent intergranular hydraulic conductivity of the intact shale and the regional values represent secondary permeability due to fractures. Calculations based on fracture flow theory demonstrate that small fractures could account for the observed differences

  11. Influence of altered precipitation pattern on greenhouse gas emissions and soil enzyme activities in Pannonian soils

    Science.gov (United States)

    Forstner, Stefan Johannes; Michel, Kerstin; Berthold, Helene; Baumgarten, Andreas; Wanek, Wolfgang; Zechmeister-Boltenstern, Sophie; Kitzler, Barbara

    2013-04-01

    Precipitation patterns are likely to be altered due to climate change. Recent models predict a reduction of mean precipitation during summer accompanied by a change in short-term precipitation variability for central Europe. Correspondingly, the risk for summer drought is likely to increase. This may especially be valid for regions which already have the potential for rare, but strong precipitation events like eastern Austria. Given that these projections hold true, soils in this area will receive water irregularly in few, heavy rainfall events and be subjected to long-lasting dry periods in between. This pattern of drying/rewetting can alter soil greenhouse gas fluxes, creating a potential feedback mechanism for climate change. Microorganisms are the key players in most soil carbon (C) and nitrogen (N) transformation processes including greenhouse gas exchange. A conceptual model proposed by Schimel and colleagues (2007) links microbial stress-response physiology to ecosystem-scale biogeochemical processes: In order to cope with decreasing soil water potential, microbes modify resource allocation patterns from growth to survival. However, it remains unclear how microbial resource acquisition via extracellular enzymes and microbial-controlled greenhouse gas fluxes respond to water stress induced by soil drying/rewetting. We designed a laboratory experiment to test for effects of multiple drying/rewetting cycles on soil greenhouse gas fluxes (CO2, CH4, N2O, NO), microbial biomass and extracellular enzyme activity. Three soils representing the main soil types of eastern Austria were collected in June 2012 at the Lysimeter Research Station of the Austrian Agency for Health and Food Safety (AGES) in Vienna. Soils were sieved to 2mm, filled in steel cylinders and equilibrated for one week at 50% water holding capacity (WHC) for each soil. Then soils were separated into two groups: One group received water several times per week (C=control), the other group received

  12. Dielectric spectra of proteins in conducting media

    International Nuclear Information System (INIS)

    Ruderman, G.; Xammar Oro, J.R. de

    1990-10-01

    Dielectric measurements of serum albumin and myoglobin in solutions of varying conductivities were performed. The results presented confirm that also for protein solutions, the Maxwell predictions of a threshold frequency in conducting materials holds. The threshold frequency of a serum albumin solution was experimentally determined. Attention should be recalled that, if the dielectric spectra of proteins solutions want to be measured, three distinct frequency regions are to be observed: a low frequency region, where the sample behaves like a conductor; an intermediate region centered around the threshold frequency, where the free charges partially screen the fixed ones; and a high frequency region where the sample behaves like a good dielectric. (author). 8 refs, 5 figs

  13. 40 CFR 81.77 - Puerto Rico Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Puerto Rico Air Quality Control Region... PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.77 Puerto Rico Air Quality Control Region. The Puerto Rico Air Quality Control Region...

  14. Heterochronicity of white matter development and aging explains regional patient control differences in schizophrenia.

    Science.gov (United States)

    Kochunov, Peter; Ganjgahi, Habib; Winkler, Anderson; Kelly, Sinead; Shukla, Dinesh K; Du, Xiaoming; Jahanshad, Neda; Rowland, Laura; Sampath, Hemalatha; Patel, Binish; O'Donnell, Patricio; Xie, Zhiyong; Paciga, Sara A; Schubert, Christian R; Chen, Jian; Zhang, Guohao; Thompson, Paul M; Nichols, Thomas E; Hong, L Elliot

    2016-12-01

    Altered brain connectivity is implicated in the development and clinical burden of schizophrenia. Relative to matched controls, schizophrenia patients show (1) a global and regional reduction in the integrity of the brain's white matter (WM), assessed using diffusion tensor imaging (DTI) fractional anisotropy (FA), and (2) accelerated age-related decline in FA values. In the largest mega-analysis to date, we tested if differences in the trajectories of WM tract development influenced patient-control differences in FA. We also assessed if specific tracts showed exacerbated decline with aging. Three cohorts of schizophrenia patients (total n = 177) and controls (total n = 249; age = 18-61 years) were ascertained with three 3T Siemens MRI scanners. Whole-brain and regional FA values were extracted using ENIGMA-DTI protocols. Statistics were evaluated using mega- and meta-analyses to detect effects of diagnosis and age-by-diagnosis interactions. In mega-analysis of whole-brain averaged FA, schizophrenia patients had lower FA (P = 10 -11 ) and faster age-related decline in FA (P = 0.02) compared with controls. Tract-specific heterochronicity measures, that is, abnormal rates of adolescent maturation and aging explained approximately 50% of the regional variance effects of diagnosis and age-by-diagnosis interaction in patients. Interactive, three-dimensional visualization of the results is available at www.enigma-viewer.org. WM tracts that mature later in life appeared more sensitive to the pathophysiology of schizophrenia and were more susceptible to faster age-related decline in FA values. Hum Brain Mapp 37:4673-4688, 2016. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

  15. Three-dimensional magnetic resonance spectroscopic imaging in the substantia nigra of healthy controls and patients with Parkinson's disease

    International Nuclear Information System (INIS)

    Groeger, Adriane; Godau, Jana; Berg, Daniela; Chadzynski, Grzegorz; Klose, Uwe

    2011-01-01

    To investigate the substantia nigra in patients with Parkinson's disease three-dimensional magnetic resonance spectroscopic imaging with high spatial resolution at 3 Tesla was performed. Regional variations of spectroscopic data between the rostral and caudal regions of the substantia nigra as well as the midbrain tegmentum areas were evaluated in healthy controls and patients with Parkinson's disease. Nine patients with Parkinson's disease and eight age- and gender-matched healthy controls were included in this study. Data were acquired by using three-dimensional magnetic resonance spectroscopic imaging measurements. The ratios between rostral and caudal voxels of the substantia nigra as well as the midbrain tegmentum areas were calculated for the main-metabolites N-acetyl aspartate, creatine, choline, and myo-inositol. Additionally, the metabolite/creatine ratios were calculated. In all subjects spectra of acceptable quality could be obtained with a nominal voxel size of 0.252 ml. The calculated rostral-to-caudal ratios of the metabolites as well as of the metabolite/creatine ratios showed with exception of choline/creatine ratio significant differences between healthy controls and patients with Parkinson's disease. The findings from this study indicate that regional variations in N-acetyl aspartate/creatine ratios in the regions of the substantia nigra may differentiate patients with Parkinson's disease and healthy controls. (orig.)

  16. Wood density and anatomy of three Eucalyptus species: implications for hydraulic conductivity

    OpenAIRE

    Barotto, Antonio J.; Monteoliva, Silvia; Gyenge, Javier; Martínez-Meier, Alejandro; Moreno, Karen; Tesón, Natalia; Fernández, María Elena

    2017-01-01

    Aim of the study: To characterize wood anatomical traits of three Eucalyptus species that differ in wood density and ecological requirements, and to examine the relationships between some anatomical features, wood density, and theoretical xylem hydraulic conductivity (Ks).Area of study: We analyzed 86 trees from three sites of Argentina (Entre Ríos and Buenos Aires Provinces).Methods: The sampled trees were Eucalyptus globulus, E. grandis and E. viminalis ranging from 11 to 15 years old. One ...

  17. Performance of Globally Linearized Controller and Two Region Fuzzy Logic Controller on a Nonlinear Process

    Directory of Open Access Journals (Sweden)

    N. Jaya

    2008-10-01

    Full Text Available In this work, a design and implementation of a Conventional PI controller, single region fuzzy logic controller, two region fuzzy logic controller and Globally Linearized Controller (GLC for a two capacity interacting nonlinear process is carried out. The performance of this process using single region FLC, two region FLC and GLC are compared with the performance of conventional PI controller about an operating point of 50 %. It has been observed that GLC and two region FLC provides better performance. Further, this procedure is also validated by real time experimentation using dSPACE.

  18. Rewetting of semi-dried ink patterns by vapour annealing for developing a reflow process in reverse offset printing

    International Nuclear Information System (INIS)

    Kusaka, Yasuyuki; Ushijima, Hirobumi; Sugihara, Kazuyoshi; Koutake, Masayoshi

    2017-01-01

    A process for reflowing patterned materials for reverse offset printing was developed, with the aim of mitigating the step-coverage problem in multilayered devices. The proposed reflow process involves a single step of vapour annealing at moderate temperatures ranging from 60 to 70 °C. This step successfully changes the height profile of semi-dried ink patterns formed on a silicone blanket, from an initially rectangular shape to a rounded shape. A systematic investigation on the effects of various vapour species and vapour temperatures on the reflow process revealed that the miscibility between the vapour and the ink, and a low boiling point of the respective solvent (high vapour pressure) are the prerequisites for successful reflows of semi-dried ink layers patterned on a silicone blanket. The results suggested that the rewetting of previously semi-dried patterns is the main mechanism in the reflow process, which led to a change in the height profile. Furthermore, the reflowed patterns demonstrated almost identical peak-height thicknesses, irrespective of the width of the patterns. This is a unique property that is unattainable by other printing methods, including gravure offset printing and microcontact printing, wherein printed patterns have rounded shapes without a reflow process, but their thickness inevitably depends on the pattern sizes. (technical note)

  19. Shape synchronization control for three-dimensional chaotic systems

    International Nuclear Information System (INIS)

    Huang, Yuanyuan; Wang, Yinhe; Chen, Haoguang; Zhang, Siying

    2016-01-01

    This paper aims to the three-dimensional continuous chaotic system and shape of the chaotic attractor by utilizing the basic theory of plane curves in classical differential geometry, the continuous controller is synthesized for the master–slave synchronization in shape. This means that the slave system can possess the same shape of state trajectory with the master system via the continuous controller. The continuous controller is composed of three sub-controllers, which respectively correspond to the master–slave synchronization in shape for the three projective curves of the chaotic attractor onto the three coordinate planes. Moreover, the proposed shape synchronization technique as well as application of control scheme to secure communication is also demonstrated in this paper, where numerical simulation results show the proposed control method works well.

  20. Linear Modeling of the Three-Phase Diode Front-Ends with Reduced Capacitance Considering the Continuous Conduction Mode

    DEFF Research Database (Denmark)

    Máthé, Lászlo; Yang, Feng; Wang, Dong

    2016-01-01

    for the entire drive systems have to be designed. A linearization and simplification to single phase model can be performed; however, when inductance is present at the grid side its performance is not satisfactory. The problem is mainly caused by neglecting the continuous conduction mode of the rectifier......Reducing the DC-link capacitance considerably is a new trend in many applications, such as: motor drives, electrolysers etc.. A straight forward method for modelling the diode front-end is to build a non-linear diode based model. This non-linear model gives difficulties when the controllers...... in the simplified model. This article proposes a simplified linear model where the continuous conduction mode is also considered. The DC-link voltage and current waveforms obtained through the proposed simplified model matches very well the waveforms obtained with the three phase diode based model and also...

  1. Problems of two-phase flows in water cooled and moderated reactors

    International Nuclear Information System (INIS)

    Syu, Yu.

    1984-01-01

    Heat exchange in two-phase flows of coolant in loss of coolant accidents in PWR and BWR reactors has been investigated. Three main stages of accident history are considered: blowdown, reflooding using emergency core cooling system and rewetting. Factors, determining the rate of coolant leakage and the rate of temperature increase in fuel cladding during blowdown, processes of vapour during reflooding and liquid priming by vapour during rewetting, are discussed

  2. Three-dimensional magnetotelluric inversion in practice—the electrical conductivity structure of the San Andreas Fault in Central California

    Science.gov (United States)

    Tietze, Kristina; Ritter, Oliver

    2013-10-01

    3-D inversion techniques have become a widely used tool in magnetotelluric (MT) data interpretation. However, with real data sets, many of the controlling factors for the outcome of 3-D inversion are little explored, such as alignment of the coordinate system, handling and influence of data errors and model regularization. Here we present 3-D inversion results of 169 MT sites from the central San Andreas Fault in California. Previous extensive 2-D inversion and 3-D forward modelling of the data set revealed significant along-strike variation of the electrical conductivity structure. 3-D inversion can recover these features but only if the inversion parameters are tuned in accordance with the particularities of the data set. Based on synthetic 3-D data we explore the model space and test the impacts of a wide range of inversion settings. The tests showed that the recovery of a pronounced regional 2-D structure in inversion of the complete impedance tensor depends on the coordinate system. As interdependencies between data components are not considered in standard 3-D MT inversion codes, 2-D subsurface structures can vanish if data are not aligned with the regional strike direction. A priori models and data weighting, that is, how strongly individual components of the impedance tensor and/or vertical magnetic field transfer functions dominate the solution, are crucial controls for the outcome of 3-D inversion. If deviations from a prior model are heavily penalized, regularization is prone to result in erroneous and misleading 3-D inversion models, particularly in the presence of strong conductivity contrasts. A `good' overall rms misfit is often meaningless or misleading as a huge range of 3-D inversion results exist, all with similarly `acceptable' misfits but producing significantly differing images of the conductivity structures. Reliable and meaningful 3-D inversion models can only be recovered if data misfit is assessed systematically in the frequency

  3. Healthy dietary patterns decrease the risk of colorectal cancer in the Mecca Region, Saudi Arabia: a case-control study.

    Science.gov (United States)

    Azzeh, Firas S; Alshammari, Eyad M; Alazzeh, Awfa Y; Jazar, Abdelelah S; Dabbour, Ibrahim R; El-Taani, Hani A; Obeidat, Ahmed A; Kattan, Fayrooz A; Tashtoush, Sufyan H

    2017-06-29

    Colorectal cancer (CRC) is the first most common cancer in males and the third most common cancer in females in Saudi Arabia. Dietary habits are strongly associated with the inhibition or proliferation of malignancy. Therefore, this study is aiming to investigate the risks and protective benefits of dietary factors affecting CRC in the Mecca region of Saudi Arabia. A case-control study was conducted from June 2014 to March 2015. One hundred thirty-seven patients with colon and/or rectal cancer were recruited in the case group, while 164 healthy participants were recruited in the control group. A questionnaire was completed with the help of trained dietitians to study the effects of several dietary patterns on the risk of CRC. Dairy product intake of 1-5 servings/day, legume intake of 3-5 servings/week, leafy vegetables intake of 1-5 servings/week, olive oil intake of 1-5 servings/week, black tea intake of three or more cups/day, and coffee intake of one or more cups/day was found to decrease the risk of CRC in participants. This study highlights the importance of changing dietary habits to decrease CRC incidence in the Mecca region.

  4. Light sensitive memristor with bi-directional and wavelength-dependent conductance control

    Energy Technology Data Exchange (ETDEWEB)

    Maier, P.; Hartmann, F., E-mail: fabian.hartmann@physik.uni-wuerzburg.de; Emmerling, M.; Schneider, C.; Kamp, M.; Worschech, L. [Technische Physik and Wilhelm Conrad Röntgen Research Center for Complex Material Systems, Physikalisches Institut, Universität Würzburg, Am Hubland, D-97074 Würzburg (Germany); Rebello Sousa Dias, M. [Departamento de Fisica, Universidade Federal de São Carlos, 13565-905 São Carlos, São Paulo (Brazil); Institute for Research in Electronics and Applied Physics, University of Maryland, College Park, Maryland 20742 (United States); Castelano, L. K.; Marques, G. E.; Lopez-Richard, V. [Departamento de Fisica, Universidade Federal de São Carlos, 13565-905 São Carlos, São Paulo (Brazil); Höfling, S. [Technische Physik and Wilhelm Conrad Röntgen Research Center for Complex Material Systems, Physikalisches Institut, Universität Würzburg, Am Hubland, D-97074 Würzburg (Germany); SUPA, School of Physics and Astronomy, University of St. Andrews, St. Andrews KY16 9SS (United Kingdom)

    2016-07-11

    We report the optical control of localized charge on positioned quantum dots in an electro-photo-sensitive memristor. Interband absorption processes in the quantum dot barrier matrix lead to photo-generated electron-hole-pairs that, depending on the applied bias voltage, charge or discharge the quantum dots and hence decrease or increase the conductance. Wavelength-dependent conductance control is observed by illumination with red and infrared light, which leads to charging via interband and discharging via intraband absorption. The presented memristor enables optical conductance control and may thus be considered for sensory applications in artificial neural networks as light-sensitive synapses or optically tunable memories.

  5. Light sensitive memristor with bi-directional and wavelength-dependent conductance control

    International Nuclear Information System (INIS)

    Maier, P.; Hartmann, F.; Emmerling, M.; Schneider, C.; Kamp, M.; Worschech, L.; Rebello Sousa Dias, M.; Castelano, L. K.; Marques, G. E.; Lopez-Richard, V.; Höfling, S.

    2016-01-01

    We report the optical control of localized charge on positioned quantum dots in an electro-photo-sensitive memristor. Interband absorption processes in the quantum dot barrier matrix lead to photo-generated electron-hole-pairs that, depending on the applied bias voltage, charge or discharge the quantum dots and hence decrease or increase the conductance. Wavelength-dependent conductance control is observed by illumination with red and infrared light, which leads to charging via interband and discharging via intraband absorption. The presented memristor enables optical conductance control and may thus be considered for sensory applications in artificial neural networks as light-sensitive synapses or optically tunable memories.

  6. Spiral inflector and central region study for three cyclotrons at CIAE

    International Nuclear Information System (INIS)

    Zhang Tianjue; Yao Hongjuan; Guan Fengping; Chu Chengjie; Lu Yinlong; Jia Xianlu; Zhong Junqing; Yang Jianjun; Xing Jiansheng; Lin Yuzheng

    2007-01-01

    The beam dynamics behaviour in the compact cyclotron central region is investigated. The design study for central region, including the spiral inflector, Dee tip, shield and posts, for three cyclotrons at CIAE will be described in this paper. The code development by CIAE and the UNIX based codes developed by TRIUMF were implemented on WINDOWS/PC by CIAE for the spiral inflector and central region design will be given too

  7. Assessment of regional air quality resulting from emission control in the Pearl River Delta region, southern China.

    Science.gov (United States)

    Wang, N; Lyu, X P; Deng, X J; Guo, H; Deng, T; Li, Y; Yin, C Q; Li, F; Wang, S Q

    2016-12-15

    To evaluate the impact of emission control measures on the air quality in the Pearl River Delta (PRD) region of South China, statistic data including atmospheric observations, emissions and energy consumptions during 2006-2014 were analyzed, and a Weather Research and Forecasting - Community Multi-scale Air Quality (WRF-CMAQ) model was used for various scenario simulations. Although energy consumption doubled from 2004 to 2014 and vehicle number significantly increased from 2006 to 2014, ambient SO 2 , NO 2 and PM 10 were reduced by 66%, 20% and 24%, respectively, mainly due to emissions control efforts. In contrast, O 3 increased by 19%. Model simulations of three emission control scenarios, including a baseline (a case in 2010), a CAP (a case in 2020 assuming control strength followed past control tendency) and a REF (a case in 2020 referring to the strict control measures based on recent policy/plans) were conducted to investigate the variations of air pollutants to the changes in NO x , VOCs and NH 3 emissions. Although the area mean concentrations of NO x , nitrate and PM 2.5 decreased under both NO x CAP (reduced by 1.8%, 0.7% and 0.2%, respectively) and NO x REF (reduced by 7.2%, 1.8% and 0.3%, respectively), a rising of PM 2.5 was found in certain areas as reducing NO x emissions elevated the atmospheric oxidizability. Furthermore, scenarios with NH 3 emission reductions showed that nitrate was sensitive to NH 3 emissions, with decreasing percentages of 0-10.6% and 0-48% under CAP and REF, respectively. Controlling emissions of VOCs reduced PM 2.5 in the southwestern PRD where severe photochemical pollution frequently occurred. It was also found that O 3 formation in PRD was generally VOCs-limited while turned to be NO x -limited in the afternoon (13:00-17:00), suggesting that cutting VOCs emissions would reduce the overall O 3 concentrations while mitigating NO x emissions in the afternoon could reduce the peak O 3 levels. Copyright © 2016 Elsevier B

  8. Regional Controller | IDRC - International Development Research ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Identifies, assesses and manages financial and administrative risks together with officers responsible for projects situated in the region by conducting recipient institutional assessments at key points in the project life-cycle, by giving advice to recipients and, where warranted, by organizing training for recipients in the area of ...

  9. Thermal conductivity measurements of Pacific illite sediment

    International Nuclear Information System (INIS)

    Hickox, C.E.; McVey, D.F.; Miller, J.B.; Olson, L.O.; Silva, A.J.

    1986-01-01

    Results are reported for effective thermal conductivity measurements performed in situ and in core samples of illite marine sediment. The measurements were obtained during a recent oceanographic expedition to a study site in the north central region of the Pacific Ocean. This study was undertaken in support of the US Subseabed Disposal Project, the purpose of which is to investigate the scientific feasibility of using the fine grained sediments of the sea floor as a repository for high level nuclear waste. In situ measurements were made and 1.5-meter long hydrostatic piston cores were taken, under remote control, from a platform that was lowered to the sea floor, 5844 m below sea level. The in situ measurement of thermal conductivity was made at a nominal depth of 80 cm below the sediment surface using a specially developed, line source, needle probe. Thermal conductivity measurements in three piston cores and one box core (obtained several kilometers from the study site) were made on shipboard using a miniature needle probe. The in situ thermal conductivity was approximately 0.91 W/m.K. Values determined from the cores were within the range 0.81 to 0.89 W/m.K

  10. Regional two-dimensional magnetotelluric profile in West Bohemia/Vogtland reveals deep conductive channel into the earthquake swarm region

    Science.gov (United States)

    Muñoz, Gerard; Weckmann, Ute; Pek, Josef; Kováčiková, Světlana; Klanica, Radek

    2018-03-01

    The West Bohemia/Vogtland region, characterized by the intersection of the Eger (Ohře) Rift and the Mariánské Lázně fault, is a geodynamically active area exhibiting repeated occurrence of earthquake swarms, massive CO2 emanations and mid Pleistocene volcanism. The Eger Rift is the only known intra-continental region in Europe where such deep seated, active lithospheric processes currently take place. We present an image of electrical resistivity obtained from two-dimensional inversion of magnetotelluric (MT) data acquired along a regional profile crossing the Eger Rift. At the near surface, the Cheb basin and the aquifer feeding the mofette fields of Bublák and Hartoušov have been imaged as part of a region of very low resistivity. The most striking resistivity feature, however, is a deep reaching conductive channel which extends from the surface into the lower crust spatially correlated with the hypocentres of the seismic events of the Nový Kostel Focal Zone. This channel has been interpreted as imaging a pathway from a possible mid-crustal fluid reservoir to the surface. The resistivity model reinforces the relation between the fluid circulation along deep-reaching faults and the generation of the earthquakes. Additionally, a further conductive channel has been revealed to the south of the profile. This other feature could be associated to fossil hydrothermal alteration related to Mýtina and/or Neualbenreuth Maar structures or alternatively could be the signature of a structure associated to the suture between the Saxo-Thuringian and Teplá-Barrandian zones, whose surface expression is located only a few kilometres away.

  11. An Improved Backstepping-Based Controller for Three-Dimensional Trajectory Tracking of a Midwater Trawl System

    Directory of Open Access Journals (Sweden)

    Zhao Yan

    2016-01-01

    Full Text Available An improved backstepping control method for three-dimensional trajectory tracking of a midwater trawl system is investigated. A new mathematical model of the trawl system while considering the horizontal expansion effect of two otter boards is presented based on the Newton Euler method. Subsequently, an active path tracking strategy of the trawl system based on the backstepping method is proposed. The nonstrict feedback characteristic of the proposed model employs a control allocation method and several parallel nonlinear PID (Proportion Integration Differentiation controllers to eliminate the high-order state variables. Then, the stability analysis by the Lyapunov Stability Theory shows that the proposed controller can maintain the stability of the trawl system even with the presence of external disturbances. To validate the proposed controller, a simulation comparison with a linear PID controller was conducted. The simulation results illustrate that the improved backstepping controller is effective for three-dimensional trajectory tracking of the midwater trawl system.

  12. Control of electrical conduction in DNA using hole doping

    Science.gov (United States)

    Lee, Hea-Yeon; Taniguchi, Masateru; Yoo, K. H.; Otsuka, Youichi; Tanaka, Hidekazu; Kawai, Tomoji

    2002-03-01

    Control of electrical conduction in DNA using hole doping H.Y.Lee1, M.Taniguchi1, K.H.Yoo2, Y.Otsuka1 H.Tanaka1 and T.Kawai1 1The Institute of Scientific and Industrial Research(ISIR), Osaka University, Osaka, Japan. 2Department of Physics, Younsei University, Seoul, Korea Possible applications of DNA molecules in electronic devices and biosensors were suggested almost ten years ago A DNA structure containing a single type of base pair appears to be a good candidate for conduction along the \\x81E-electron clouds of the stacked bases. There have been lots of investigations on conduction mechanisms of the DNA molecules. However, it is not still clear whether the observed conductions of some DNA molecules come from motions of either ionic charges or other carriers. Although the basic mechanism for DNA-mediated charge transport should be understood for electronic applications, there have been divergent reports on its nature. And I will be present the research for the charge carrier conduction of DNA film under oxygen and iodine gas by using 10¡V100 nm gap. The doping studies using oxygen and iodine gas can provide a definite answer for the carrier conduction mechanism and also a possible method to control the carrier concentration in DNA molecules. Using oxygen and iodine adsorption experiments on the poly (dG)-poly (dC) DNA molecules, we will show that their conductance becomes increased easily by several orders of magnitudes due to the hole doping, which is a characteristic behavior of a p-type semiconductor. On the other hand, we will also show that the poly (dA) - poly (dT) DNA molecules behave as an n-type semiconductor. Our works indicate that the concentration and the type of carriers in the DNA molecules could be controlled using proper doping methods. We expect that this would be a major breakthrough in DNA-based nano-electronics, similar to the fact that the doped conductive has polyacetylene opened up a new field of electronics with exciting implications

  13. 40 CFR 81.104 - Central Pennsylvania Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.104 Section 81.104 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.104 Central Pennsylvania Intrastate Air Quality Control Region. The Central Pennsylvania Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  14. 40 CFR 81.43 - Metropolitan Toledo Interstate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.43 Section 81.43 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.43 Metropolitan Toledo Interstate Air Quality Control Region. The Metropolitan Toledo Interstate Air Quality Control Region (Ohio-Michigan) consists of the territorial area...

  15. 40 CFR 81.31 - Metropolitan Providence Interstate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.31 Section 81.31 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.31 Metropolitan Providence Interstate Air Quality Control Region. The Metropolitan Providence Interstate Air Quality Control Region (Rhode Island-Massachusetts) consists of the...

  16. 40 CFR 81.90 - Androscoggin Valley Interstate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.90 Section 81.90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.90 Androscoggin Valley Interstate Air Quality Control Region. The Androscoggin Valley Interstate Air Quality Control Region (Maine-New Hampshire) consists of the territorial...

  17. 40 CFR 81.78 - Metropolitan Portland Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.78 Section 81.78 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.78 Metropolitan Portland Intrastate Air Quality Control Region. The Metropolitan Portland Intrastate Air Quality Control Region (Maine) consists of the territorial area...

  18. 40 CFR 81.30 - Southeastern Wisconsin Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.30 Section 81.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.30 Southeastern Wisconsin Intrastate Air Quality Control Region. The Metropolitan Milwaukee Intrastate Air Quality Control Region (Wisconsin) has been renamed the Southeastern...

  19. 40 CFR 81.16 - Metropolitan Denver Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.16 Section 81.16 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.16 Metropolitan Denver Intrastate Air Quality Control Region. The Metropolitan Denver Intrastate Air Quality Control Region (Colorado) consists of the territorial area...

  20. 40 CFR 81.47 - Central Oklahoma Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.47 Section 81.47 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.47 Central Oklahoma Intrastate Air Quality Control Region. The Metropolitan Oklahoma Intrastate Air Quality Control Region has been renamed the Central Oklahoma Intrastate...

  1. 40 CFR 81.29 - Metropolitan Indianapolis Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Air Quality Control Region. 81.29 Section 81.29 Protection of Environment ENVIRONMENTAL PROTECTION... Designation of Air Quality Control Regions § 81.29 Metropolitan Indianapolis Intrastate Air Quality Control Region. The Metropolitan Indianapolis Intrastate Air Quality Control Region consists of the territorial...

  2. 40 CFR 81.101 - Metropolitan Dubuque Interstate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.101 Section 81.101 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.101 Metropolitan Dubuque Interstate Air Quality Control Region. The Metropolitan Dubuque Interstate Air Quality Control Region (Illinois-Iowa-Wisconsin) consists of the...

  3. 40 CFR 81.79 - Northeastern Oklahoma Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.79 Section 81.79 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.79 Northeastern Oklahoma Intrastate Air Quality Control Region. The Metropolitan Tulsa Intrastate Air Quality Control Region has been renamed the Northeastern Oklahoma Intrastate...

  4. 40 CFR 81.24 - Niagara Frontier Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.24 Section 81.24 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.24 Niagara Frontier Intrastate Air Quality Control Region. The Niagara Frontier Intrastate Air Quality Control Region (New York) consists of the territorial area...

  5. 40 CFR 81.106 - Greenville-Spartanburg Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.106 Section 81.106 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.106 Greenville-Spartanburg Intrastate Air Quality Control Region. The Greenville-Spartanburg Intrastate Air Quality Control Region (South Carolina) consists of the territorial...

  6. 40 CFR 81.44 - Metropolitan Memphis Interstate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.44 Section 81.44 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.44 Metropolitan Memphis Interstate Air Quality Control Region. The Metropolitan Memphis Interstate Air Quality Control Region (Arkansas-Mississippi-Tennessee) consists of the...

  7. 40 CFR 81.19 - Metropolitan Boston Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.19 Section 81.19 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.19 Metropolitan Boston Intrastate Air Quality Control Region. The Metropolitan Boston Intrastate Air Quality Control Region (Massachusetts) consists of the territorial area...

  8. 40 CFR 81.28 - Metropolitan Baltimore Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.28 Section 81.28 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.28 Metropolitan Baltimore Intrastate Air Quality Control Region. The Metropolitan Baltimore Intrastate Air Quality Control Region (Maryland) consists of the territorial area...

  9. 40 CFR 81.119 - Western Tennessee Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.119 Section 81.119 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.119 Western Tennessee Intrastate Air Quality Control Region. The Western Tennessee Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  10. 40 CFR 81.89 - Metropolitan Cheyenne Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.89 Section 81.89 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.89 Metropolitan Cheyenne Intrastate Air Quality Control Region. The Metropolitan Cheyenne Intrastate Air Quality Control Region (Wyoming) consists of the territorial area...

  11. 40 CFR 81.87 - Metropolitan Boise Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.87 Section 81.87 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.87 Metropolitan Boise Intrastate Air Quality Control Region. The Metropolitan Boise Intrastate Air Quality Control Region (Idaho) consists of the territorial area encompassed...

  12. 40 CFR 81.23 - Southwest Pennsylvania Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.23 Section 81.23 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.23 Southwest Pennsylvania Intrastate Air Quality Control Region. The Southwest Pennsylvania Intrastate Air Quality Control Region is redesignated to consist of the territorial...

  13. 40 CFR 81.75 - Metropolitan Charlotte Interstate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.75 Section 81.75 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.75 Metropolitan Charlotte Interstate Air Quality Control Region. The Metropolitan Charlotte Interstate Air Quality Control Region (North Carolina-South Carolina) has been revised...

  14. 40 CFR 81.120 - Middle Tennessee Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.120 Section 81.120 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.120 Middle Tennessee Intrastate Air Quality Control Region. The Middle Tennessee Intrastate Air Quality Control Region consists of the territorial area encompassed by...

  15. 40 CFR 81.117 - Southeast Missouri Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.117 Section 81.117 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.117 Southeast Missouri Intrastate Air Quality Control Region. The Southeast Missouri Intrastate Air Quality Control Region consists of the territorial area encompassed by the...

  16. 40 CFR 81.45 - Metropolitan Atlanta Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.45 Section 81.45 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.45 Metropolitan Atlanta Intrastate Air Quality Control Region. The Metropolitan Atlanta Intrastate Air Quality Control Region (Georgia) has been revised to consist of the...

  17. 40 CFR 81.123 - Southeastern Oklahoma Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.123 Section 81.123 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.123 Southeastern Oklahoma Intrastate Air Quality Control Region. The Southeastern Oklahoma Intrastate Air Quality Control Region consists of the territorial area encompassed by the...

  18. 40 CFR 81.98 - Burlington-Keokuk Interstate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.98 Section 81.98 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.98 Burlington-Keokuk Interstate Air Quality Control Region. The Burlington-Keokuk Interstate Air Quality Control Region (Illinois-Iowa) is revised to consist of the...

  19. 40 CFR 81.49 - Southeast Florida Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.49 Section 81.49 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.49 Southeast Florida Intrastate Air Quality Control Region. The Southeast Florida Intrastate Air Quality Control Region is redesignated to consist of the territorial area...

  20. 40 CFR 81.59 - Cumberland-Keyser Interstate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.59 Section 81.59 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.59 Cumberland-Keyser Interstate Air Quality Control Region. The Cumberland-Keyser Interstate Air Quality Control Region (Maryland-West Virginia) has been revised to consist...

  1. 40 CFR 81.20 - Metropolitan Cincinnati Interstate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.20 Section 81.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.20 Metropolitan Cincinnati Interstate Air Quality Control Region. The Metropolitan Cincinnati Interstate Air Quality Control Region (Ohio-Kentucky-Indiana) is revised to consist of...

  2. 40 CFR 81.97 - Southwest Florida Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.97 Section 81.97 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.97 Southwest Florida Intrastate Air Quality Control Region. The Southwest Florida Intrastate Air Quality Control Region consists of the territorial area encompassed by the...

  3. 40 CFR 81.116 - Northern Missouri Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.116 Section 81.116 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.116 Northern Missouri Intrastate Air Quality Control Region. The Northern Missouri Intrastate Air Quality Control Region consists of the territorial area encompassed by the...

  4. 40 CFR 81.67 - Lake Michigan Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Regions § 81.67 Lake Michigan Intrastate Air Quality Control Region. The Menominee-Escanaba (Michigan)-Marinette (Wisconsin) Interstate Air Quality Control Region has been renamed the Lake Michigan Intrastate Air Quality Control Region (Wisconsin) and revised to consist of the territorial area...

  5. 40 CFR 81.34 - Metropolitan Dayton Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.34 Section 81.34 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.34 Metropolitan Dayton Intrastate Air Quality Control Region. The Metropolitan Dayton Intrastate Air Quality Control Region consists of the territorial area encompassed by the...

  6. 40 CFR 81.115 - Northwest Nevada Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.115 Section 81.115 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.115 Northwest Nevada Intrastate Air Quality Control Region. The Northwest Nevada Intrastate Air Quality Control Region consists of the territorial area encompassed by the...

  7. 40 CFR 81.41 - Metropolitan Birmingham Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.41 Section 81.41 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.41 Metropolitan Birmingham Intrastate Air Quality Control Region. The Metropolitan Birmingham Intrastate Air Quality Control Region (Alabama) has been revised to consist of the...

  8. 40 CFR 81.14 - Metropolitan Chicago Interstate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.14 Section 81.14 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.14 Metropolitan Chicago Interstate Air Quality Control Region. The Metropolitan Chicago Interstate Air Quality Control Region (Illinois-Indiana) is revised to consist of the...

  9. 40 CFR 81.118 - Southwest Missouri Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.118 Section 81.118 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.118 Southwest Missouri Intrastate Air Quality Control Region. The Southwest Missouri Intrastate Air Quality Control Region consists of the territorial area encompassed by the...

  10. 40 CFR 81.122 - Mississippi Delta Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.122 Section 81.122 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.122 Mississippi Delta Intrastate Air Quality Control Region. The Mississippi Delta Intrastate Air Quality Control Region consists of the territorial area encompassed by the...

  11. Conductive polymer nanotube patch for fast and controlled ex vivo transdermal drug delivery.

    Science.gov (United States)

    Nguyen, Thao M; Lee, Sebin; Lee, Sang Bok

    2014-10-01

    To uptake and release hydrophilic model drugs and insulin in a novel conductive polymer (CP) nanotube transdermal patch. The externally controlled transdermal delivery of model drugs and insulin were tested ex vivo and results were compared with CP films. The unique intrinsic properties of CPs provide electrostatic interaction between the model drugs and polymer backbone. When a pulsed potential was applied, the drug delivery release profile mimics that of injection delivery. With a constant potential applied, the release rate constants of the patch system were up to three-times faster than the control (0 V) and released approximately 80% more drug molecules over 24 h. The CP nanotube transdermal patch represents a new and promising drug method, specifically for hydrophilic molecules, which have been a large obstacle for conventional transdermal drug delivery systems.

  12. Hemiptera Mitochondrial Control Region: New Sights into the Structural Organization, Phylogenetic Utility, and Roles of Tandem Repetitions of the Noncoding Segment

    Directory of Open Access Journals (Sweden)

    Kui Li

    2018-04-01

    Full Text Available As a major noncoding fragment, the control region (CR of mtDNA is responsible for the initiation of mitogenome transcription and replication. Several structural features of CR sequences have been reported in many insects. However, comprehensive analyses on the structural organization and phylogenetic utility, as well as the role of tandem replications (TRs on length variation, high A+T content, and shift of base skew of CR sequences are poorly investigated in hemipteran insects. In this study, we conducted a series of comparative analyses, using 116 samples covering all 11 infraorders of the five currently recognized monophyletic groups in the Hemiptera. Several structural elements (mononucleotide stretches containing conserved sequence blocks (CSBs, TRs, and GA-rich region were identified in the mitochondrial control region in hemipteran insects, without showing a consistent location. The presence and absence of certain specific structural elements in CR sequences show the various structural organizations of that segment among the five monophyletic groups, which indicates the diversification of the control region’s structural organization in Hemiptera. Among the many groups within Hemiptera, eight monophyletic groups and three consistent phylogenetic trees were recovered, using CSBs datasets by maximum likelihood and Bayesian methods, which suggests the possible utility of CR sequences for phylogenetic reconstruction in certain groups of Hemiptera. Statistical analyses showed that TRs may contribute to the length variation, high AT content, and the shift of base skewing of CR sequences toward high AT content in the Hemiptera. Our findings enrich the knowledge of structural organization, phylogenetic utility, and roles of tandem replication of hemipteran CR, and provide a possible framework for mitochondrial control region analyses in hemimetabolous insects.

  13. 40 CFR 81.48 - Champlain Valley Interstate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Region. 81.48 Section 81.48 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.48 Champlain Valley Interstate Air Quality Control Region. The Champlain Valley Interstate Air Quality Control Region (Vermont-New York) has been revised to consist of the...

  14. 40 CFR 81.111 - Georgetown Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Regions § 81.111 Georgetown Intrastate Air Quality Control Region. The Georgetown Intrastate Air Quality Control Region (South Carolina) consists of the territorial area encompassed by the... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Georgetown Intrastate Air Quality...

  15. 40 CFR 81.107 - Greenwood Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Regions § 81.107 Greenwood Intrastate Air Quality Control Region. The Greenwood Intrastate Air Quality Control Region (South Carolina) consists of the territorial area encompassed by the... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Greenwood Intrastate Air Quality...

  16. 40 CFR 81.108 - Columbia Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Regions § 81.108 Columbia Intrastate Air Quality Control Region. The Columbia Intrastate Air Quality Control Region (South Carolina) consists of the territorial area encompassed by the... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Columbia Intrastate Air Quality...

  17. 40 CFR 81.109 - Florence Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Regions § 81.109 Florence Intrastate Air Quality Control Region. The Florence Intrastate Air Quality Control Region (South Carolina) consists of the territorial area encompassed by the... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Florence Intrastate Air Quality...

  18. 40 CFR 81.35 - Louisville Interstate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Regions § 81.35 Louisville Interstate Air Quality Control Region. The Louisville Interstate Air Quality Control Region (Kentucky-Indiana) consists of the territorial area encompassed by the... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Louisville Interstate Air Quality...

  19. Prevalence and risk factors associated with Theileria parva infection in cattle in three regions of Tanzania

    DEFF Research Database (Denmark)

    Kerario, Isack I.; Simuunza, Martin C; Chenyambuga, Sebastian W

    2017-01-01

    of ECF in Tanzania has continued to be a challenge due to inadequate epidemiological information. The main objective of this study was to determine the epidemiological situation of Theileria parva infections in cattle kept under pastoral and agro-pastoral farming systems in Mara, Singida, and Mbeya...... not found to be significant predictors of being PCR positive for T. parva. The present study showed high variation in tick burden and T. parva prevalence across the regions. Therefore, different strategic planning and cost-effective control measures for ticks and T. parva infection should be implemented...... regions of Tanzania. Blood samples were collected from 648 cattle in the three regions. Genomic DNA was extracted and amplified in a polymerase chain reaction (PCR) using T. parva-specific primers targeting the 104-kD antigen (P104) gene. In addition, information was collected on the possible risk factors...

  20. 40 CFR 81.42 - Chattanooga Interstate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Regions § 81.42 Chattanooga Interstate Air Quality Control Region. The Chattanooga Interstate Air Quality Control Region (Georgia-Tennessee) has been revised to consist of the territorial area... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Chattanooga Interstate Air Quality...

  1. Vowel change across three age groups of speakers in three regional varieties of American English

    Science.gov (United States)

    Jacewicz, Ewa; Fox, Robert A.; Salmons, Joseph

    2011-01-01

    This acoustic study examines sound (vowel) change in apparent time across three successive generations of 123 adult female speakers ranging in age from 20 to 65 years old, representing three regional varieties of American English, typical of western North Carolina, central Ohio and southeastern Wisconsin. A set of acoustic measures characterized the dynamic nature of formant trajectories, the amount of spectral change over the course of vowel duration and the position of the spectral centroid. The study found a set of systematic changes to /I, ε, æ/ including positional changes in the acoustic space (mostly lowering of the vowels) and significant variation in formant dynamics (increased monophthongization). This common sound change is evident in both emphatic (articulated clearly) and nonemphatic (casual) productions and occurs regardless of dialect-specific vowel dispersions in the vowel space. The cross-generational and cross-dialectal patterns of variation found here support an earlier report by Jacewicz, Fox, and Salmons (2011) which found this recent development in these three dialect regions in isolated citation-form words. While confirming the new North American Shift in different styles of production, the study underscores the importance of addressing the stress-related variation in vowel production in a careful and valid assessment of sound change. PMID:22125350

  2. Vowel change across three age groups of speakers in three regional varieties of American English.

    Science.gov (United States)

    Jacewicz, Ewa; Fox, Robert A; Salmons, Joseph

    2011-10-01

    This acoustic study examines sound (vowel) change in apparent time across three successive generations of 123 adult female speakers ranging in age from 20 to 65 years old, representing three regional varieties of American English, typical of western North Carolina, central Ohio and southeastern Wisconsin. A set of acoustic measures characterized the dynamic nature of formant trajectories, the amount of spectral change over the course of vowel duration and the position of the spectral centroid. The study found a set of systematic changes to /I, ε, æ/ including positional changes in the acoustic space (mostly lowering of the vowels) and significant variation in formant dynamics (increased monophthongization). This common sound change is evident in both emphatic (articulated clearly) and nonemphatic (casual) productions and occurs regardless of dialect-specific vowel dispersions in the vowel space. The cross-generational and cross-dialectal patterns of variation found here support an earlier report by Jacewicz, Fox, and Salmons (2011) which found this recent development in these three dialect regions in isolated citation-form words. While confirming the new North American Shift in different styles of production, the study underscores the importance of addressing the stress-related variation in vowel production in a careful and valid assessment of sound change.

  3. Control of conducting polymer actuators without physical feedback: simulated feedback control approach with particle swarm optimization

    International Nuclear Information System (INIS)

    Xiang, Xingcan; Mutlu, Rahim; Alici, Gursel; Li, Weihua

    2014-01-01

    Conducting polymer actuators have shown significant potential in articulating micro instruments, manipulation devices, and robotics. However, implementing a feedback control strategy to enhance their positioning ability and accuracy in any application requires a feedback sensor, which is extremely large in size compared to the size of the actuators. Therefore, this paper proposes a new sensorless control scheme without the use of a position feedback sensor. With the help of the system identification technique and particle swarm optimization, the control scheme, which we call the simulated feedback control system, showed a satisfactory command tracking performance for the conducting polymer actuator’s step and dynamic displacement responses, especially under a disturbance, without needing a physical feedback loop, but using a simulated feedback loop. The primary contribution of this study is to propose and experimentally evaluate the simulated feedback control scheme for a class of the conducting polymer actuators known as tri-layer polymer actuators, which can operate both in dry and wet media. This control approach can also be extended to other smart actuators or systems, for which the feedback control based on external sensing is impractical. (paper)

  4. Research of a Novel Three-dimensional Force Flexible Tactile Sensor Based on Conductive Rubber

    Directory of Open Access Journals (Sweden)

    Fei Xu

    2010-09-01

    Full Text Available A novel three-dimensional force flexible tactile sensor using conductive rubber with "overall injection molding" technique is presented. The sensor is based on conductive rubber’s force-sensitive property. The sensor is flexible and can measure 3-D force. The rubber’s characteristics, the sensor’s structure and its principle are described. The results of simulation will be also presented.

  5. An evaluation of the regional supply of biomass at three midwestern sites

    Energy Technology Data Exchange (ETDEWEB)

    English, B.C.; Dillivan, K.D.; Ojo, M.A.; Alexander, R.R. [Univ. of Tennessee, Knoxville, TN (United States); Graham, R.L. [Oak Ridge National Lab., TN (United States)

    1993-12-31

    Research has been conducted on both the agronomy and the conversion of biomass. However, few studies have been initiated that combine the knowledge of growing biomass with site specific resource availability information. An economic appraisal of how much biomass might be grown in a specific area for a given price has only just been initiated. This paper examines the economics of introducing biomass production to three midwest representative areas centered on the following counties, Orange County, Indiana; Olmsted County, Minnesota; and Cass County, North Dakota. Using a regional linear programming model, estimates of economic feasibility as well as environmental impacts are made. At a price of $53 per metric ton the biomass supplied to the plant gate is equal to 183,251 metric tons. At $62 per metric ton the biomass supply has increased to almost 1 million metric tons. The model predicts a maximum price of $88 per metric ton and at this price, 2,748,476 metric tons of biomass are produced.

  6. Far-IR transparency and dynamic infrared signature control with novel conducting polymer systems

    Science.gov (United States)

    Chandrasekhar, Prasanna; Dooley, T. J.

    1995-09-01

    Materials which possess transparency, coupled with active controllability of this transparency in the infrared (IR), are today an increasingly important requirement, for varied applications. These applications include windows for IR sensors, IR-region flat panel displays used in camouflage as well as in communication and sight through night-vision goggles, coatings with dynamically controllable IR-emissivity, and thermal conservation coatings. Among stringent requirements for these applications are large dynamic ranges (color contrast), 'multi-color' or broad-band characteristics, extended cyclability, long memory retention, matrix addressability, small area fabricability, low power consumption, and environmental stability. Among materials possessing the requirements for variation of IR signature, conducting polymers (CPs) appear to be the only materials with dynamic, actively controllable signature and acceptable dynamic range. Conventional CPs such as poly(alkyl thiophene), poly(pyrrole) or poly(aniline) show very limited dynamic range, especially in the far-IR, while also showing poor transparency. We have developed a number of novel CP systems ('system' implying the CP, the selected dopant, the synthesis method, and the electrolyte) with very wide dynamic range (up to 90% in both important IR regions, 3 - 5 (mu) and 8 - 12 (mu) ), high cyclability (to 105 cycles with less than 10% optical degradation), nearly indefinite optical memory retention, matrix addressability of multi-pixel displays, very wide operating temperature and excellent environmental stability, low charge capacity, and processability into areas from less than 1 mm2 to more than 100 cm2. The criteria used to design and arrive at these CP systems, together with representative IR signature data, are presented in this paper.

  7. Control of water infiltration into near-surface, low-level waste-disposal units in humid regions

    International Nuclear Information System (INIS)

    O'Donnell, E.; Ridky, R.W.; Schulz, R.K.

    1994-01-01

    This study's objective is to assess means for controlling water infiltration through waste-disposal unit covers in humid regions. Experimental work is being performed in large-scale lysimeters (75 ft x 45 ft x 10 ft) at Beltsville, Maryland. Results of the assessment are applicable to disposal of low-level radioactive waste (LLW), uranium mill tailings, hazardous waste, and sanitary landfills. Three kinds of waste-disposal unit covers or barriers to water infiltration are being investigated: (1) resistive layer barrier, (2) conductive layer barrier, and (3) bioengineering management. The resistive layer barrier consists of compacted earthen material (e.g., clay). The conductive layer barrier consists of a conductive layer in conjunction with a capillary break. As long as unsaturated flow conditions are maintained, the conductive layer will wick water around the capillary break. Below-grade layered covers such as (1) and (2) will fail if there is appreciable subsidence of the cover, and remedial action for this kind of failure will be difficult. A surface cover, called bioengineering management, is meant to overcome this problem. The bioengineering management surface barrier is easily repairable if damaged by subsidence; therefore, it could be the system of choice under active subsidence conditions. The bioengineering management procedure also has been shown to be effective in dewatering saturated trenches and could be used for remedial action efforts. After cessation of subsidence, that procedure could be replaced by a resistive layer barrier or, perhaps even better, by a resistive layer barrier/conductive layer barrier system. The latter system would then give long-term effective protection against water entry into waste without institutional care

  8. Thermal conductivity and stability of a three-phase blend of carbon nanotubes, conductive polymer, and silver nanoparticles incorporated into polycarbonate nanocomposites

    KAUST Repository

    Patole, Archana

    2015-04-16

    Metallic and non-metallic nanofillers can be used together in the design of polycarbonate (PC) nanocomposites with improved electrical properties. Here, the preparation of three-phase blend (carbon nanotubes (CNT), silver nanoparticles, and conductive polymer) in a two-step process before incorporation in the PC is reported. First, ethylene diamine functionalized multiwall carbon nanotubes (MWCNT-EDA) were decorated with Ag nanoparticles. Next, the Ag-decorated CNTs were coated with poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS). Due to the high thermal conductivity instrinsic to both metallic and non-metallic phases, it is expected that the thermal properties of the resulting nanocomposite would largely differ from those of pristine PC. We thus investigated in detail how this hybrid conductive blend affected properties such as the glass transition temperature, the thermal stability, and the thermal conductivity of the nanocomposite. It was found that this strategy results in improved thermal conductivity and thermal stability of the material. © 2015 Wiley Periodicals, Inc.

  9. Thermal conductivity and stability of a three-phase blend of carbon nanotubes, conductive polymer, and silver nanoparticles incorporated into polycarbonate nanocomposites

    KAUST Repository

    Patole, Archana; Ventura, Isaac Aguilar; Lubineau, Gilles

    2015-01-01

    Metallic and non-metallic nanofillers can be used together in the design of polycarbonate (PC) nanocomposites with improved electrical properties. Here, the preparation of three-phase blend (carbon nanotubes (CNT), silver nanoparticles, and conductive polymer) in a two-step process before incorporation in the PC is reported. First, ethylene diamine functionalized multiwall carbon nanotubes (MWCNT-EDA) were decorated with Ag nanoparticles. Next, the Ag-decorated CNTs were coated with poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS). Due to the high thermal conductivity instrinsic to both metallic and non-metallic phases, it is expected that the thermal properties of the resulting nanocomposite would largely differ from those of pristine PC. We thus investigated in detail how this hybrid conductive blend affected properties such as the glass transition temperature, the thermal stability, and the thermal conductivity of the nanocomposite. It was found that this strategy results in improved thermal conductivity and thermal stability of the material. © 2015 Wiley Periodicals, Inc.

  10. Control of water infiltration into near surface low-level waste disposal units. Final report on field experiments at a humid region site, Beltsville, Maryland

    International Nuclear Information System (INIS)

    Schulz, R.K.; Ridky, R.W.; O'Donnell, E.

    1997-09-01

    This study''s objective was to assess means for controlling water infiltration through waste disposal unit covers in humid regions. Experimental work was carried out in large-scale lysimeters 21.34 m x 13.72 m x 3.05 m (70 ft x 45 ft x 10 ft) at Beltsville, Maryland. Results of the assessment are applicable to disposal of low-level radioactive waste (LLW), uranium mill tailings, hazardous waste, and sanitary landfills. Three kinds of waste disposal unit covers or barriers to water infiltration were investigated: (1) resistive layer barrier, (2) conductive layer barrier, and (3) bioengineering management

  11. The regional costs and benefits of acid rain control

    International Nuclear Information System (INIS)

    Berkman, M.P.

    1991-01-01

    Congress recently enacted acid rain control legislation as part of the 1990 Clean Air Act Amendments following a decade-long debate among disparate regional interests. Although Congress succeeded in drafting a law acceptable to all regions, the regional costs and benefits of the legislation remain uncertain. The research presented here attempts to estimate the regional costs and benefits and the economic impacts of acid rain controls. These estimates are made using a modeling system composed of econometric, linear programming and input-output models. The econometric and linear programming components describe markets for electricity and coal. The outputs of these components including capital investment, electricity demand, and coal production are taken as exogenous inputs by a multiregional input-output model. The input-output model produces estimates of changes in final demand, gross output, and employment. The utility linear programming model also predicts sulfur dioxide emissions (an acid-rain precursor). According to model simulations, the costs of acid rain control exceed the benefits for many regions including several regions customarily thought to be the major beneficiaries of acid rain control such as New England

  12. Sensitivity study with respect to direction of ADI method during re-flooding in AHWR

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, M.; Mukhopadhyay, D. [Bhabha Atomic Research Centre, Mumbai (India). Reactor Safety Div.; Ghosh, A.K. [Bhabha Atomic Research Centre, Mumbai (India). Raja Ramanna Fellow; Kumar, R. [Indian Institute of Technology, Roorkee (India)

    2015-05-15

    The Advanced Heavy water Reactor (AHWR) is a natural circulation vertical pressure tube type boiling light water cooled and heavy water moderated reactor. As the AHWR fuel bundle quenching under accident condition is designed primarily with radial jets at several axial locations, bottom re-flooding still remain open as another option. Radial direction injection of emergency core cooling leads to rewetting of AHWR fuel cluster in circumferential direction. A 3D fuel pin model has been developed by using Finite Difference Method (FDM) of transient heat conduction equation. Alternating Direction Implicit technique of Finite Difference Method (FDM) has been used for discretisation of numerical equation in different time step at different direction. Sensitivity numerical study with respect to direction of ADI method has been carried out to optimize the time step during the transient as well as steady state and is found that it is insensitivity with direction of solution. Further, to assess influence of circumferential rewetting vis-a-vis axial rewetting. Both the analyses are carried out with same fluid temperature and heat transfer coefficients as boundary conditions. It has been found from the analyses that for radial jet, the circumferential conduction is significant and overall the fuel temperature falls in the quench plane with the initiation of quenching event. The paper discusses the sensitivity study with respect to direction of ADI solution and comparison of numerical results for circumferential and axial rewetting for single pin.

  13. Phonon dispersion and thermal conductivity of nanocrystal superlattices using three-dimensional atomistic models

    International Nuclear Information System (INIS)

    Zanjani, Mehdi B.; Lukes, Jennifer R.

    2014-01-01

    A computational study of thermal conductivity and phonon dispersion of gold nanocrystal superlattices is presented. Phonon dispersion curves, reported here for the first time from combined molecular dynamics and lattice dynamics calculations, show multiple phononic band gaps and consist of many more dispersion branches than simple atomic crystals. Fully atomistic three dimensional molecular dynamics calculations of thermal conductivity using the Green Kubo method are also performed for the first time on these materials. Thermal conductivity is observed to increase for increasing nanocrystal core size and decrease for increasing surface ligand density. Our calculations predict values in the range 0.1–1 W/m K that are consistent with reported experimental results

  14. Situational analysis of tuberculosis control programs in the Eastern Mediterranean Region: Gaps and solutions

    Directory of Open Access Journals (Sweden)

    Samiha Baghdadi

    2016-01-01

    Conclusion: The year 2015 marks a transition from the MDGs to the Sustainable Development Goals and from the Stop TB Strategy to the End TB Strategy. The region will move into three main directions: complete pending tasks, mitigate the impact of the complex emergencies on TB control, and move toward TB elimination.

  15. Heat transfer in the thermal entrance region of a circular tube with axial heat conduction

    International Nuclear Information System (INIS)

    Zhang Changquan.

    1985-01-01

    This paper recounts the effects of axial heat conduction and convective boundary conditions on the heat transfer in the thermal entrance region of a circular tube under uniform flow, and the corresponding calculation is made. It will be profitable for the heat transfer studies on the pipe entrance region of low Prandtl number (liquid metal), or flow of low Peclet number. (author)

  16. Healthy dietary patterns decrease the risk of colorectal cancer in the Mecca Region, Saudi Arabia: a case-control study

    Directory of Open Access Journals (Sweden)

    Firas S. Azzeh

    2017-06-01

    Full Text Available Abstract Background Colorectal cancer (CRC is the first most common cancer in males and the third most common cancer in females in Saudi Arabia. Dietary habits are strongly associated with the inhibition or proliferation of malignancy. Therefore, this study is aiming to investigate the risks and protective benefits of dietary factors affecting CRC in the Mecca region of Saudi Arabia. Methods A case-control study was conducted from June 2014 to March 2015. One hundred thirty-seven patients with colon and/or rectal cancer were recruited in the case group, while 164 healthy participants were recruited in the control group. A questionnaire was completed with the help of trained dietitians to study the effects of several dietary patterns on the risk of CRC. Results Dairy product intake of 1–5 servings/day, legume intake of 3–5 servings/week, leafy vegetables intake of 1–5 servings/week, olive oil intake of 1–5 servings/week, black tea intake of three or more cups/day, and coffee intake of one or more cups/day was found to decrease the risk of CRC in participants. Conclusion This study highlights the importance of changing dietary habits to decrease CRC incidence in the Mecca region.

  17. Comparison of three control methods for an autonomous vehicle

    Science.gov (United States)

    Deshpande, Anup; Mathur, Kovid; Hall, Ernest

    2010-01-01

    The desirability and challenge of developing a completely autonomous vehicle and the rising need for more efficient use of energy by automobiles motivate this research- a study for an optimum solution to computer control of energy efficient vehicles. The purpose of this paper is to compare three control methods - mechanical, hydraulic and electric that have been used to convert an experimental all terrain vehicle to drive by wire which would eventually act as a test bed for conducting research on various technologies for autonomous operation. Computer control of basic operations in a vehicle namely steering, braking and speed control have been implemented and will be described in this paper. The output from a 3 axis motion controller is used for this purpose. The motion controller is interfaced with a software program using WSDK (Windows Servo Design Kit) as an intermediate tuning layer for tuning and parameter settings in autonomous operation. The software program is developed in C++. The voltage signal sent to the motion controller can be varied through the control program for desired results in controlling the steering motor, activating the hydraulic brakes and varying the vehicle's speed. The vehicle has been tested for its basic functionality which includes testing of street legal operations and also a 1000 mile test while running in a hybrid mode. The vehicle has also been tested for control when it is interfaced with devices such as a keyboard, joystick and sensors under full autonomous operation. The vehicle is currently being tested in various safety studies and is being used as a test bed for experiments in control courses and research studies. The significance of this research is in providing a greater understanding of conventional driving controls and the possibility of improving automobile safety by removing human error in control of a motor vehicle.

  18. Cerebral glucose metabolism in Wernicke's, Broca's, and conduction aphasia

    Energy Technology Data Exchange (ETDEWEB)

    Metter, E.J.; Kempler, D.; Jackson, C.; Hanson, W.R.; Mazziotta, J.C.; Phelps, M.E.

    1989-01-01

    Cerebral glucose metabolism was evaluated in patients with either Wernicke's (N = 7), Broca's (N = 11), or conduction (N = 10) aphasia using /sup 18/F-2-fluoro-2-deoxy-D-glucose with positron emission tomography. The three aphasic syndromes differed in the degree of left-to-right frontal metabolic asymmetry, with Broca's aphasia showing severe asymmetry and Wernicke's aphasia mild-to-moderate metabolic asymmetry, while patients with conduction aphasia were metabolically symmetric. On the other hand, the three syndromes showed the same degree of metabolic decline in the left temporal region. The parietal region appeared to separate conduction aphasia from both Broca's and Wernicke's aphasias. Common aphasic features in the three syndromes appear to be due to common changes in the temporal region, while unique features were associated with frontal and parietal metabolic differences.

  19. Bilingualism alters brain functional connectivity between "control" regions and "language" regions: Evidence from bimodal bilinguals.

    Science.gov (United States)

    Li, Le; Abutalebi, Jubin; Zou, Lijuan; Yan, Xin; Liu, Lanfang; Feng, Xiaoxia; Wang, Ruiming; Guo, Taomei; Ding, Guosheng

    2015-05-01

    Previous neuroimaging studies have revealed that bilingualism induces both structural and functional neuroplasticity in the dorsal anterior cingulate cortex (dACC) and the left caudate nucleus (LCN), both of which are associated with cognitive control. Since these "control" regions should work together with other language regions during language processing, we hypothesized that bilingualism may also alter the functional interaction between the dACC/LCN and language regions. Here we tested this hypothesis by exploring the functional connectivity (FC) in bimodal bilinguals and monolinguals using functional MRI when they either performed a picture naming task with spoken language or were in resting state. We found that for bimodal bilinguals who use spoken and sign languages, the FC of the dACC with regions involved in spoken language (e.g. the left superior temporal gyrus) was stronger in performing the task, but weaker in the resting state as compared to monolinguals. For the LCN, its intrinsic FC with sign language regions including the left inferior temporo-occipital part and right inferior and superior parietal lobules was increased in the bilinguals. These results demonstrate that bilingual experience may alter the brain functional interaction between "control" regions and "language" regions. For different control regions, the FC alters in different ways. The findings also deepen our understanding of the functional roles of the dACC and LCN in language processing. Copyright © 2015 Elsevier Ltd. All rights reserved.

  20. Ultrathin Graphite Foam: A Three-Dimensional Conductive Network for Battery Electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Ji, HX; Zhang, LL; Pettes, MT; Li, HF; Chen, SS; Shi, L; Piner, R; Ruoff, RS

    2012-05-01

    We report the use of free-standing, lightweight, and highly conductive ultrathin graphite foam (UGF), loaded with lithium iron phosphate (LFP), as a cathode in a lithium ion battery. At a high charge/discharge current density of 1280 mA g(-1), the specific capacity of the LFP loaded on UGF was 70 mAh g(-1), while LFP loaded on Al foil failed. Accounting for the total mass of the electrode, the maximum specific capacity of the UGF/LFP cathode was 23% higher than that of the Al/LFP cathode and 170% higher than that of the Ni-foam/LFP cathode. Using UGF, both a higher rate capability and specific capacity can be achieved simultaneously, owing to its conductive (similar to 1.3 x 10(5) S m(-1) at room temperature) and three-dimensional lightweight (similar to 9.5 mg cm(-3)) graphitic structure. Meanwhile, UGF presents excellent electrochemical stability comparing to that of Al and Ni foils, which are generally used as conductive substrates in lithium ion batteries. Moreover, preparation of the UGF electrode was facile, cost-effective, and compatible with various electrochemically active materials.

  1. Thermal conductivity measurements of pacific illite sediment

    Science.gov (United States)

    Hickox, C. E.; McVey, D. F.; Miller, J. B.; Olson, L. O.; Silva, A. J.

    1986-07-01

    Results are reported for effective thermal conductivity measurements performed in situ and in core samples of illite marine sediment. The measurements were obtained during a recent oceanographic expedition to a study site in the north central region of the Pacific Ocean. This study was undertaken in support of the U.S. Subseabed Disposal Project, the purpose of which is to investigate the scientific feasibility of using the fine-grained sediments of the sea floor as a repository for high-level nuclear waste. In situ measurements were made and 1.5-m-long hydrostatic piston cores were taken, under remote control, from a platform that was lowered to the sea floor, 5844 m below sea level. The in situ measurement of thermal conductivity was made at a nominal depth of 80 cm below the sediment surface using a specially developed, line-source, needle probe. Thermal conductivity measurements in three piston cores and one box core (obtained several kilometers from the study site) were made on shipboard using a miniature needle probe. The in situ thermal conductivity was approximately 0.91 W · m-1 · K-1. Values determined from the cores were within the range 0.81 to 0.89 W · m-1 · K-1.

  2. Controlling single-molecule junction conductance by molecular interactions

    Science.gov (United States)

    Kitaguchi, Y.; Habuka, S.; Okuyama, H.; Hatta, S.; Aruga, T.; Frederiksen, T.; Paulsson, M.; Ueba, H.

    2015-01-01

    For the rational design of single-molecular electronic devices, it is essential to understand environmental effects on the electronic properties of a working molecule. Here we investigate the impact of molecular interactions on the single-molecule conductance by accurately positioning individual molecules on the electrode. To achieve reproducible and precise conductivity measurements, we utilize relatively weak π-bonding between a phenoxy molecule and a STM-tip to form and cleave one contact to the molecule. The anchoring to the other electrode is kept stable using a chalcogen atom with strong bonding to a Cu(110) substrate. These non-destructive measurements permit us to investigate the variation in single-molecule conductance under different but controlled environmental conditions. Combined with density functional theory calculations, we clarify the role of the electrostatic field in the environmental effect that influences the molecular level alignment. PMID:26135251

  3. Control of weakly conductive fluids by near wall Lorentz forces

    Energy Technology Data Exchange (ETDEWEB)

    Hinze, M. [Technische Univ. Dresden (Germany). Inst. fuer Numerische Mathematik

    2007-07-01

    In this work optimal and model-predictive control approaches for control of weakly conductive fluids are developed. The flow around the circular cylinder at low Reynolds numbers serves as prototyping application. Control by near-wall Lorentz forces gains either to suppress the formation of the von Karman Vortex Street, or to reduce the drag. Besides a concise mathematical modelling numerical examples are presented which highlight the scope of the presented control approaches. (orig.)

  4. Handgrip Strength: Indications of Paternal Inheritance in Three European Regions

    DEFF Research Database (Denmark)

    Cournil, Amandine; Jeune, Bernard; Skytthe, Axel

    2010-01-01

    BACKGROUND: Handgrip strength is an indicator of overall muscle strength. Poor handgrip strength is a risk factor for disability and mortality. We aimed to investigate the pattern of inheritance of handgrip strength in a sample of parent-offspring pairs from three different European regions...

  5. 40 CFR 81.62 - Northeast Mississippi Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Northeast Mississippi Intrastate Air... Air Quality Control Regions § 81.62 Northeast Mississippi Intrastate Air Quality Control Region. The Alabama-Mississippi-Tennessee Interstate Air Quality Control Region has been renamed the Northeast...

  6. 40 CFR 81.216 - Northeast Indiana Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Northeast Indiana Intrastate Air... Air Quality Control Regions § 81.216 Northeast Indiana Intrastate Air Quality Control Region. The Northeast Indiana Intrastate Air Quality Control Region (Indiana) consists of the territorial area...

  7. 40 CFR 81.162 - Northeast Plateau Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Northeast Plateau Intrastate Air... Air Quality Control Regions § 81.162 Northeast Plateau Intrastate Air Quality Control Region. The Northeast Plateau Intrastate Air Quality Control Region (California) consists of the territorial area...

  8. Estimation of regional-scale groundwater flow properties in the Bengal Basin of India and Bangladesh

    Science.gov (United States)

    Michael, H.A.; Voss, C.I.

    2009-01-01

    Quantitative evaluation of management strategies for long-term supply of safe groundwater for drinking from the Bengal Basin aquifer (India and Bangladesh) requires estimation of the large-scale hydrogeologic properties that control flow. The Basin consists of a stratified, heterogeneous sequence of sediments with aquitards that may separate aquifers locally, but evidence does not support existence of regional confining units. Considered at a large scale, the Basin may be aptly described as a single aquifer with higher horizontal than vertical hydraulic conductivity. Though data are sparse, estimation of regional-scale aquifer properties is possible from three existing data types: hydraulic heads, 14C concentrations, and driller logs. Estimation is carried out with inverse groundwater modeling using measured heads, by model calibration using estimated water ages based on 14C, and by statistical analysis of driller logs. Similar estimates of hydraulic conductivities result from all three data types; a resulting typical value of vertical anisotropy (ratio of horizontal to vertical conductivity) is 104. The vertical anisotropy estimate is supported by simulation of flow through geostatistical fields consistent with driller log data. The high estimated value of vertical anisotropy in hydraulic conductivity indicates that even disconnected aquitards, if numerous, can strongly control the equivalent hydraulic parameters of an aquifer system. ?? US Government 2009.

  9. The first insight into the metabolite profiling of grapes from three Vitis vinifera L. cultivars of two controlled appellation (DOC) regions.

    Science.gov (United States)

    Teixeira, António; Martins, Viviana; Noronha, Henrique; Eiras-Dias, José; Gerós, Hernâni

    2014-03-10

    The characterization of the metabolites accumulated in the grapes of specific cultivars grown in different climates is of particular importance for viticulturists and enologists. In the present study, the metabolite profiling of grapes from the cultivars, Alvarinho, Arinto and Padeiro de Basto, of two Portuguese Controlled Denomination of Origin (DOC) regions (Vinho Verde and Lisboa) was investigated by gas chromatography-coupled time-of-flight mass spectrometry (GC-TOF-MS) and an amino acid analyzer. Primary metabolites, including sugars, organic acids and amino acids, and some secondary metabolites were identified. Tartaric and malic acids and free amino acids accumulated more in grapes from vines of the DOC region of Vinho Verde than DOC Lisboa, but a principal component analysis (PCA) plot showed that besides the DOC region, the grape cultivar also accounted for the variance in the relative abundance of metabolites. Grapes from the cultivar, Alvarinho, were particularly rich in malic acid and tartaric acids in both DOC regions, but sucrose accumulated more in the DOC region of Vinho Verde.

  10. The First Insight into the Metabolite Profiling of Grapes from Three Vitis vinifera L. Cultivars of Two Controlled Appellation (DOC Regions

    Directory of Open Access Journals (Sweden)

    António Teixeira

    2014-03-01

    Full Text Available The characterization of the metabolites accumulated in the grapes of specific cultivars grown in different climates is of particular importance for viticulturists and enologists. In the present study, the metabolite profiling of grapes from the cultivars, Alvarinho, Arinto and Padeiro de Basto, of two Portuguese Controlled Denomination of Origin (DOC regions (Vinho Verde and Lisboa was investigated by gas chromatography-coupled time-of-flight mass spectrometry (GC-TOF-MS and an amino acid analyzer. Primary metabolites, including sugars, organic acids and amino acids, and some secondary metabolites were identified. Tartaric and malic acids and free amino acids accumulated more in grapes from vines of the DOC region of Vinho Verde than DOC Lisboa, but a principal component analysis (PCA plot showed that besides the DOC region, the grape cultivar also accounted for the variance in the relative abundance of metabolites. Grapes from the cultivar, Alvarinho, were particularly rich in malic acid and tartaric acids in both DOC regions, but sucrose accumulated more in the DOC region of Vinho Verde.

  11. Three-dimensional magnetic resonance spectroscopic imaging in the substantia nigra of healthy controls and patients with Parkinson's disease

    Energy Technology Data Exchange (ETDEWEB)

    Groeger, Adriane; Godau, Jana; Berg, Daniela [University of Tuebingen, Department of Neurodegeneration, Hertie Institute for Clinical Brain Research and German Center for Neurodegenerative Disease (DZNE), Tuebingen (Germany); Chadzynski, Grzegorz; Klose, Uwe [University Hospital Tuebingen, Department of Diagnostic and Interventional Neuroradiology, Tuebingen (Germany)

    2011-09-15

    To investigate the substantia nigra in patients with Parkinson's disease three-dimensional magnetic resonance spectroscopic imaging with high spatial resolution at 3 Tesla was performed. Regional variations of spectroscopic data between the rostral and caudal regions of the substantia nigra as well as the midbrain tegmentum areas were evaluated in healthy controls and patients with Parkinson's disease. Nine patients with Parkinson's disease and eight age- and gender-matched healthy controls were included in this study. Data were acquired by using three-dimensional magnetic resonance spectroscopic imaging measurements. The ratios between rostral and caudal voxels of the substantia nigra as well as the midbrain tegmentum areas were calculated for the main-metabolites N-acetyl aspartate, creatine, choline, and myo-inositol. Additionally, the metabolite/creatine ratios were calculated. In all subjects spectra of acceptable quality could be obtained with a nominal voxel size of 0.252 ml. The calculated rostral-to-caudal ratios of the metabolites as well as of the metabolite/creatine ratios showed with exception of choline/creatine ratio significant differences between healthy controls and patients with Parkinson's disease. The findings from this study indicate that regional variations in N-acetyl aspartate/creatine ratios in the regions of the substantia nigra may differentiate patients with Parkinson's disease and healthy controls. (orig.)

  12. An Agent-Based Reasoning of Impacts of Regional Climate Changes on Land Use Changes in the Three-River Headwaters Region of China

    Directory of Open Access Journals (Sweden)

    Tao Zhang

    2013-01-01

    Full Text Available The land surface in Three-River Headwaters Region (TRHR, a typical ecological fragile zone of China, is quite sensitive to the climate changes which will destabilize certain ecosystem services valuable to the entire nation and neighboring countries. This study aimed to analyze the impacts of climate changes and agents’ adaptive behaviors on the regional land use changes with the agent based model (ABM. First, the main agents were extracted according to the production resources endowments and socioeconomic background. Then the agents’ land use behaviors were analyzed and parameterized. Thereafter, the ABM model was built to simulate the impacts of the climate changes on the regional land use changes and agents’ economic benefits. The results showed that the land use changes were mainly characterized by the increase of grassland and decrease of unused land area. Besides, the agents would get more wealth under the scenario without climate changes in the long term, even though the total income is lower than that under the scenario with climate changes. In addition, the sensitivity analysis indicated that the model is sensitive to the climatic conditions, market price of agricultural and animal husbandry products, government subsidies, and cost control.

  13. High-resolution liquid patterns via three-dimensional droplet shape control.

    Science.gov (United States)

    Raj, Rishi; Adera, Solomon; Enright, Ryan; Wang, Evelyn N

    2014-09-25

    Understanding liquid dynamics on surfaces can provide insight into nature's design and enable fine manipulation capability in biological, manufacturing, microfluidic and thermal management applications. Of particular interest is the ability to control the shape of the droplet contact area on the surface, which is typically circular on a smooth homogeneous surface. Here, we show the ability to tailor various droplet contact area shapes ranging from squares, rectangles, hexagons, octagons, to dodecagons via the design of the structure or chemical heterogeneity on the surface. We simultaneously obtain the necessary physical insights to develop a universal model for the three-dimensional droplet shape by characterizing the droplet side and top profiles. Furthermore, arrays of droplets with controlled shapes and high spatial resolution can be achieved using this approach. This liquid-based patterning strategy promises low-cost fabrication of integrated circuits, conductive patterns and bio-microarrays for high-density information storage and miniaturized biochips and biosensors, among others.

  14. Ecophysiological Traits of Leaves of Three Marsilea Species Distributed in Different Geographical Regions

    Directory of Open Access Journals (Sweden)

    Tai-Chung Wu

    2011-11-01

    Full Text Available Marsilea, an amphibian fern genus (containing ca. 80 species characterized by their unusual leaves and reproductive structures, is distributed over the five continents. To investigate the adaptation traits of three Marsilea species (M. crenata, M. quadrifolia, and M. schelpiana, distributed in different geographic regions, to terrestrial conditions, we compared morphological features, optical properties and photosynthetic performance of leaflets of the three species grown in terrestrial environment. The results showed that leaflets of the three species had significant differences in some of the ecophysiogical traits. Among the three species, M. quadrifolia (distributed in temperate region where receiving low precipitation had the highest trichome density on its leaflet surface and the highest water use efficiency, M. schelpiana (mainly in southern Africa where accepting high level of solar irradiance had the tallest petiole and the highest leaf dissection index, total stomatal pore area index, PSII electron transport rate and photosaturated photosynthetic rate, M. crenata (mainly in southeastern Asia region where receiving high precipitation and with high humidity had the lowest leaf dissection index and water use efficiency. Accordingly, leaf characteristics of the three Marsilea species reflect the climate pattern of their habitats. The results also suggest that water availability and light intensity are two of the important factors contributing to the geographic distribution of the three species.

  15. Health conditions and role limitation in three European Regions: a public-health perspective

    Directory of Open Access Journals (Sweden)

    Gabriela Barbaglia

    2017-01-01

    Conclusion: The contribution of health conditions to role limitation in the three European regions studied is high. Mental disorders are associated with the largest impact in most of the regions. There is a need for mainstreaming disability in the public health agenda to reduce the role limitation associated with health conditions. The cross-regional differences found require further investigation.

  16. 40 CFR 81.17 - Metropolitan Los Angeles Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Regions § 81.17 Metropolitan Los Angeles Air Quality Control Region. The Metropolitan Los Angeles Air Quality Control Region consists of the following territorial area (including the territorial... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Metropolitan Los Angeles Air Quality...

  17. 40 CFR 81.32 - Puget Sound Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Regions § 81.32 Puget Sound Intrastate Air Quality Control Region. The Puget Sound Intrastate Air Quality Control Region (Washington) consists of the territorial area encompassed by the... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Puget Sound Intrastate Air Quality...

  18. 40 CFR 81.256 - Northeast Iowa Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Northeast Iowa Intrastate Air Quality Control Region. 81.256 Section 81.256 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Quality Control Regions § 81.256 Northeast Iowa Intrastate Air Quality Control Region. The Northeast Iowa...

  19. 40 CFR 81.237 - Northeast Georgia Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Northeast Georgia Intrastate Air... Air Quality Control Regions § 81.237 Northeast Georgia Intrastate Air Quality Control Region. The Northeast Georgia Intrastate Air Quality Control Region consists of the territorial area encompassed by the...

  20. 40 CFR 81.139 - Northeast Arkansas Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Northeast Arkansas Intrastate Air... Air Quality Control Regions § 81.139 Northeast Arkansas Intrastate Air Quality Control Region. The Northeast Arkansas Intrastate Air Quality Control Region consists of the territorial area encompassed by the...

  1. 40 CFR 81.251 - Northeast Kansas Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Northeast Kansas Intrastate Air... Air Quality Control Regions § 81.251 Northeast Kansas Intrastate Air Quality Control Region. The Northeast Kansas Intrastate Air Quality Control Region consists of the territorial area encompassed by the...

  2. 40 CFR 81.134 - Austin-Waco Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Austin-Waco Intrastate Air Quality Control Region. 81.134 Section 81.134 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Quality Control Regions § 81.134 Austin-Waco Intrastate Air Quality Control Region. The Austin-Waco...

  3. 40 CFR 81.121 - Four Corners Interstate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Four Corners Interstate Air Quality Control Region. 81.121 Section 81.121 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Quality Control Regions § 81.121 Four Corners Interstate Air Quality Control Region. The Four Corners...

  4. 40 CFR 81.93 - Hampton Roads Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Hampton Roads Intrastate Air Quality Control Region. 81.93 Section 81.93 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Quality Control Regions § 81.93 Hampton Roads Intrastate Air Quality Control Region. The Metropolitan...

  5. 40 CFR 81.110 - Camden-Sumter Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Regions § 81.110 Camden-Sumter Intrastate Air Quality Control Region. The Camden-Sumter Intrastate Air Quality Control Region (South Carolina) consists of the territorial area encompassed by the... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Camden-Sumter Intrastate Air Quality...

  6. 40 CFR 81.52 - Wasatch Front Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Regions § 81.52 Wasatch Front Intrastate Air Quality Control Region. The Wasatch Front Intrastate Air Quality Control Region (Utah) consists of the territorial area encompassed by the boundaries... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Wasatch Front Intrastate Air Quality...

  7. 40 CFR 81.54 - Cook Inlet Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Regions § 81.54 Cook Inlet Intrastate Air Quality Control Region. The Cook Inlet Intrastate Air Quality Control Region (Alaska) consists of the territorial area encompassed by the boundaries... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Cook Inlet Intrastate Air Quality...

  8. 40 CFR 81.95 - Central Florida Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Regions § 81.95 Central Florida Intrastate Air Quality Control Region. The Central Florida Intrastate Air Quality Control Region consists of the territorial area encompassed by the boundaries of the... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Central Florida Intrastate Air Quality...

  9. 40 CFR 81.176 - San Luis Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 17 2010-07-01 2010-07-01 false San Luis Intrastate Air Quality Control Region. 81.176 Section 81.176 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Quality Control Regions § 81.176 San Luis Intrastate Air Quality Control Region. The San Luis Intrastate...

  10. A two-dimensional model with three regions for the reflooding study

    International Nuclear Information System (INIS)

    Motta, A.M.T.; Kinrys, S.; Roberty, N.C.; Carmo, E.G.D. do; Oliveira, L.F.S. de

    1982-01-01

    A two-dimensional semi-analytical model, with three heat transfer regions is described for the calculation of flood ratio, the length of quenching front and the temperature distribution in the cladding. (E.G.) [pt

  11. A two-dimensional model with three regions for the reflooding study

    International Nuclear Information System (INIS)

    Motta, A.M.T.; Kinrys, S.; Roberty, N.C.; Carmo, E.G.D. do; Oliveira, L.F.S. de.

    1983-02-01

    A two-dimensional semi-analytical model, with three heat transfer regions is described for the calculation of flood ratio, the lenght of quenching front and the temperature distribution in the cladding. (E.G.) [pt

  12. Characterization of RFX-mod passive conducting structures to optimize plasma start up and equilibrium control

    International Nuclear Information System (INIS)

    Marchiori, G.; Grando, L.; Cavinato, M.

    2007-01-01

    The load assembly of RFX-mod consists of three toroidal conducting structures whose eddy currents affect the plasma equilibrium magnetic configuration. The high number of electromagnetic probes mounted on the components of the load assembly allowed to analyse the response of each structure to a variation of the magnetic field vertical component. The capability of evaluating the axisymmetric toroidal currents in the passive structures and therefore their contribution to the equilibrium configuration by a 2D FE MHD equilibrium code was validated. The design and implementation of a feedback control system of the magnetic field vertical component before the gas ionization allowed meeting the requirement of an accurate control of this quantity in view of operation at higher plasma current and independently of the magnetizing winding programming

  13. Dynamic Response of Satellite-Derived Vegetation Growth to Climate Change in the Three North Shelter Forest Region in China

    Directory of Open Access Journals (Sweden)

    Bin He

    2015-08-01

    Full Text Available Since the late 1970s, the Chinese government has initiated ecological restoration programs in the Three North Shelter Forest System Project (TNSFSP area. Whether accelerated climate change will help or hinder these efforts is still poorly understood. Using the updated and extended AVHRR NDVI3g dataset from 1982 to 2011 and corresponding climatic data, we investigated vegetation variations in response to climate change. The results showed that the overall state of vegetation in the study region has improved over the past three decades. Vegetation cover significantly decreased in 23.1% and significantly increased in 21.8% of the study area. An increase in all three main vegetation types (forest, grassland, and cropland was observed, but the trend was only statistically significant in cropland. In addition, bare and sparsely vegetated areas, mainly located in the western part of the study area, have significantly expanded since the early 2000s. A moisture condition analysis indicated that the study area experienced significant climate variations, with warm-wet conditions in the western region and warm-dry conditions in the eastern region. Correlation analysis showed that variations in the Normalized Difference Vegetation Index (NDVI were positively correlated with precipitation and negatively correlated with temperature. Ultimately, climate change influenced vegetation growth by controlling the availability of soil moisture. Further investigation suggested that the positive impacts of precipitation on NDVI have weakened in the study region, whereas the negative impacts from temperature have been enhanced in the eastern study area. However, over recent years, the negative temperature impacts have been converted to positive impacts in the western region. Considering the variations in the relationship between NDVI and climatic variables, the warm–dry climate in the eastern region is likely harmful to vegetation growth, whereas the warm

  14. 40 CFR 81.80 - Las Vegas Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... Quality Control Regions § 81.80 Las Vegas Intrastate Air Quality Control Region. The Las Vegas Intrastate Air Quality Control Region (Nevada) has been revised to consist of the territorial area encompassed by... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Las Vegas Intrastate Air Quality...

  15. Regional dialogue and multilateral arms control efforts today

    International Nuclear Information System (INIS)

    Graham, T. Jr.

    1994-01-01

    The significance of arms control and non-proliferation tasks is stressed emphasising what has been done, and-more important-what must still be done. Although tangible developments at the regional level may seem at times to be slow in coming, it is important to remember that the United States-Soviet transition from voluntary declarations to detailed arms control agreements with intrusive verification regimes spanned the entire length of cold war. Given the instabilities afflicting these regions, establishing a regional dialogue is itself a confidence-building measure. The experience of the United States and the former Soviet Union amply demonstrates that mere existence of regular dialogue can reduce tension by providing a platform for communication among military and Government participants even when political crisis prevents diplomatic contacts at senior levels. The international community should be encouraged by the progress that has been made to date to address regional instabilities. Such steps are an integral part of the international effort, carried out both at the United Nations and elsewhere, to adopt acceptable levels of conventional military forces and to eliminate weapons of mass destruction. Given the instabilities afflicting these regions, establishing a regional dialogue is itself a confidence-building measure. World changes, while potentially dangerous and certainly challenging, offer the hope of replacing antagonism with cooperation, creating a progressively more democratic global environment, preventing proliferation, and dampening regional conflicts. Continuing to make effective use of the entire mix of arms control and confidence-building tools will help to realize these hopes

  16. Controlling An Inverter-Driven Three-Phase Motor

    Science.gov (United States)

    Dolland, C.

    1984-01-01

    Control system for three-phase permanent-magnet motor driven by linecommutated inverter uses signals generated by integrating back emf of each phase of motor. High-pass filter network eliminates low-frequency components from control loop while maintaining desired power factor.

  17. High-temperature current conduction through three kinds of Schottky diodes

    International Nuclear Information System (INIS)

    Fei, Li; Xiao-Ling, Zhang; Yi, Duan; Xue-Song, Xie; Chang-Zhi, Lü

    2009-01-01

    Fundamentals of the Schottky contacts and the high-temperature current conduction through three kinds of Schottky diodes are studied. N-Si Schottky diodes, GaN Schottky diodes and AlGaN/GaN Schottky diodes are investigated by I–V–T measurements ranging from 300 to 523 K. For these Schottky diodes, a rise in temperature is accompanied with an increase in barrier height and a reduction in ideality factor. Mechanisms are suggested, including thermionic emission, field emission, trap-assisted tunnelling and so on. The most remarkable finding in the present paper is that these three kinds of Schottky diodes are revealed to have different behaviours of high-temperature reverse currents. For the n-Si Schottky diode, a rise in temperature is accompanied by an increase in reverse current. The reverse current of the GaN Schottky diode decreases first and then increases with rising temperature. The AlGaN/GaN Schottky diode has a trend opposite to that of the GaN Schottky diode, and the dominant mechanisms are the effects of the piezoelectric polarization field and variation of two-dimensional electron gas charge density. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

  18. Loss-of-coolant accident test series TC-1 experiment operating specifications

    International Nuclear Information System (INIS)

    Yackle, T.R.

    1979-09-01

    The purpose of this document is to specify the experiment operating procedure for the test series TC-1. The effects of externally mounted cladding thermocouples on the fuel rod thermal behavior during LOCA blowdown and reflood cycles will be investigated in the test. Potential thermocouple effects include: (a) delayed DNB, (b) momentary cladding rewets following DNB, (c) premature cladding rewet during a blowdown two-phase slug period, and (d) early cladding rewet during reflood. The two-phase slug period will be controlled by momentarily opening the hot leg valve. The slug will consist of lower plenum liquid that is sent through the flow shrouds and will be designed to quench the fuel rods at a rate that is similar to the slug experienced early in the LOFT L2-2 and L2-3 tests

  19. Control of chaos in a three-well duffing system

    International Nuclear Information System (INIS)

    Yang Jianping; Jing Zhujun

    2009-01-01

    Analytical and numerical results concerning control of chaos in a three-well duffing system with two external excitations are given by using the Melnikov methods proposed by Chacon et al. [Chacon R. General results on chaos suppression for biharmonically driven dissipative systems. Phys Lett A 1999;257:293-300, Chacon R, Palmero F, Balibrea F. Taming chaos in a driven Josephson Junction. Int J Bifurc Chaos 2001;11(7):1897-909, Chacon R. Role of ultrasubharmonic resonances in taming chaos by weak harmonic perturbations. Europhys Lett 2001;54(2):148C153]. We theoretically give the parameter-space region and intervals of initial phase difference for primary and subharmonic resonance and the necessary condition for the superharmonic and supersubharmonic resonance, where homoclinic chaos or heteroclinic chaos can be suppressed. Numerical simulations show the consistency and difference with theoretical analysis and the chaotic behavior can be converted to periodic orbits by adjusting amplitude and phase-difference of inhibiting excitation. Moreover, we consider the influence of parametric frequency on maximum Lyapunov exponent (LE) for different phase-differences, and give the distribution of maximum Lyapunov exponents in parameter-plane, which indicates the regions of non-chaotic states (non-positive LE) and chaotic states (positive LE).

  20. Region based Brain Computer Interface for a home control application.

    Science.gov (United States)

    Akman Aydin, Eda; Bay, Omer Faruk; Guler, Inan

    2015-08-01

    Environment control is one of the important challenges for disabled people who suffer from neuromuscular diseases. Brain Computer Interface (BCI) provides a communication channel between the human brain and the environment without requiring any muscular activation. The most important expectation for a home control application is high accuracy and reliable control. Region-based paradigm is a stimulus paradigm based on oddball principle and requires selection of a target at two levels. This paper presents an application of region based paradigm for a smart home control application for people with neuromuscular diseases. In this study, a region based stimulus interface containing 49 commands was designed. Five non-disabled subjects were attended to the experiments. Offline analysis results of the experiments yielded 95% accuracy for five flashes. This result showed that region based paradigm can be used to select commands of a smart home control application with high accuracy in the low number of repetitions successfully. Furthermore, a statistically significant difference was not observed between the level accuracies.

  1. Reversible light-controlled conductance switching of azobenzene-based metal/polymer nanocomposites

    International Nuclear Information System (INIS)

    Pakula, Christina; Zaporojtchenko, Vladimir; Strunskus, Thomas; Faupel, Franz; Zargarani, Dordaneh; Herges, Rainer

    2010-01-01

    We present a new concept of light-controlled conductance switching based on metal/polymer nanocomposites with dissolved chromophores that do not have intrinsic current switching ability. Photoswitchable metal/PMMA nanocomposites were prepared by physical vapor deposition of Au and Pt clusters, respectively, onto spin-coated thin poly(methylmethacrylate) films doped with azo-dye molecules. High dye concentrations were achieved by functionalizing the azo groups with tails and branches, thus enhancing solubility. The composites show completely reversible optical switching of the absorption bands upon alternating irradiation with UV and blue light. We also demonstrate reversible light-controlled conductance switching. This is attributed to changes in the metal cluster separation upon isomerization based on model experiments where analogous conductance changes were induced by swelling of the composite films in organic vapors and by tensile stress.

  2. Growth and gene expression are predominantly controlled by distinct regions of the human IL-4 receptor.

    Science.gov (United States)

    Ryan, J J; McReynolds, L J; Keegan, A; Wang, L H; Garfein, E; Rothman, P; Nelms, K; Paul, W E

    1996-02-01

    IL-4 causes hematopoietic cells to proliferate and express a series of genes, including CD23. We examined whether IL-4-mediated growth, as measured by 4PS phosphorylation, and gene induction were similarly controlled. Studies of M12.4.1 cells expressing human IL-4R truncation mutants indicated that the region between amino acids 557-657 is necessary for full gene expression, which correlated with Stat6 DNA binding activity. This region was not required for 4PS phosphorylation. Tyrosine-to-phenylalanine mutations in the interval between amino acids 557-657 revealed that as long as one tyrosine remained unmutated, CD23 was fully induced. When all three tyrosines were mutated, the receptor was unable to induce CD23. The results indicate that growth regulation and gene expression are principally controlled by distinct regions of IL-4R.

  3. Analysis of Lattice Thermal Conductivity of Si Considering the Effect of Phonon Dispersion on Three-phonon Processes

    Science.gov (United States)

    He, Ping; Li, Zhijian

    2001-03-01

    In this work we present the new relaxation time expressions considering the detailed information of the phonon dispersion. For the three-phonon processes, it is found that only limited types of three-phonon processes are allowed to occur and the attenuation of phonon that conduct heat varies roughly with the fifth power of frequency. By using these expressions, the data of thermal conductivity of bulk silicon is well fitted. And further, the data for thin films of single crystal silicon which cannot be well fitted by the widely used model that proposed by Holland is also well fitted using the new expressions for three-phonon processes and parameters got at the previous step.

  4. Hypertension Control and Cardiometabolic Risk: A Regional Perspective

    Directory of Open Access Journals (Sweden)

    Martin Thoenes

    2012-01-01

    Full Text Available Background. We investigated the association between blood pressure control and common cardiometabolic risk factors from a global and regional perspective. Methods. In the present analysis of a large cross-sectional i-SEARCH study, 17.092 outpatients receiving antihypertensive treatment were included in 26 countries. According to clinical guidelines for the management of arterial hypertension, patients were classified based on the level of seated systolic/diastolic blood pressure (SBP/DBP. Uncontrolled hypertension was defined as SBP/DBP ≥140/90 mmHg for non-diabetics, and ≥130/80 mmHg for diabetics. Results. Overall, mean age was 63.1 years, 52.8% were male, and mean BMI was 28.9 kg/m2. Mean SBP/DBP was 148.9/87.0 mmHg, and 76.3% of patients had uncontrolled hypertension. Diabetes was present in 29.1% with mean HbA1c of 6.8%. Mean LDL-cholesterol was 3.2 mmol/L, HDL-cholesterol 1.3 mmol/L, and triglycerides 1.8 mmol/L; 49.0% had hyperlipidemia. Patients with uncontrolled hypertension had a higher BMI (29.4 versus 28.6 kg/m2, LDL-cholesterol (3.4 versus 3.0 mmol/L, triglycerides (1.9 versus 1.7 mmol/L, and HbA1c (6.8 versus 6.7% than those with controlled blood pressure (P<0.0001 for all parameters. Conclusions. Among outpatients treated for arterial hypertension, three quarters had uncontrolled blood pressure. Elevated SBP/DBP and uncontrolled hypertension were associated with increasing BMI, LDL-cholesterol, triglycerides, and HbA1c, both globally and regionally.

  5. Real life study of three years omalizumab in patients with difficult-to-control asthma.

    Science.gov (United States)

    López Tiro, J Jesús; Contreras, E Angélica Contreras; del Pozo, M Elena Ramírez; Gómez Vera, J; Larenas Linnemann, D

    2015-01-01

    Even though there are multiple options for the treatment of asthma, there still exists a fair group of patients with difficult-to-control asthma. We describe for the first time the real-world effects of three-year omalizumab treatment on patients with difficult-to-control asthma, seen in a social security hospital in a Latin American country. Difficult-to-control asthmatic patients from the out-patient clinic of a regional hospital were recruited to receive a three-year omalizumab course. Efficacy parameters were asthma control test (ACT) score; FEV1; daily beclomethasone maintenance dose; and unplanned visits for asthma exacerbations (emergency room (ER), hospitalisations, intensive care). 52 patients were recruited, 47 completed the three-year treatment (42 female, 15-67 years, mean age 43.5). Comparing efficacy parameters of the year before omalizumab with the 3rd year of omalizumab: mean ACT improved from 12.4 to 20.5, mean FEV1 from 66.3% (standard deviation (SD) 19.1%) to 88.4% (SD 16.2%) of predicted, while mean beclomethasone dose reduced from 1750 to 766 mcg/day and there was a significant reduction in patients experiencing ER visits (from 95% to 19%, pomalizumab, two because of an adverse event (anaphylaxis, severe headache, both resolved without sequelae). Omalizumab improved most clinical parameters of Mexican patients with difficult-to-control asthma. Especially the rates of ER visits and hospitalisation were significantly reduced, thus reducing costs. Omalizumab was generally well tolerated. Copyright © 2013 SEICAP. Published by Elsevier Espana. All rights reserved.

  6. 40 CFR 81.38 - Metropolitan Houston-Galveston Intrastate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Metropolitan Houston-Galveston... Designation of Air Quality Control Regions § 81.38 Metropolitan Houston-Galveston Intrastate Air Quality Control Region. The Metropolitan Houston-Galveston Intrastate Air Quality Control Region (Texas) has been...

  7. Fuzzy Logic Controlled Solar Module for Driving Three- Phase Induction Motor

    Science.gov (United States)

    Afiqah Zainal, Nurul; Sooi Tat, Chan; Ajisman

    2016-02-01

    Renewable energy produced by solar module gives advantages for generated three- phase induction motor in remote area. But, solar module's ou tput is uncertain and complex. Fuzzy logic controller is one of controllers that can handle non-linear system and maximum power of solar module. Fuzzy logic controller used for Maximum Power Point Tracking (MPPT) technique to control Pulse-Width Modulation (PWM) for switching power electronics circuit. DC-DC boost converter used to boost up photovoltaic voltage to desired output and supply voltage source inverter which controlled by three-phase PWM generated by microcontroller. IGBT switched Voltage source inverter (VSI) produced alternating current (AC) voltage from direct current (DC) source to control speed of three-phase induction motor from boost converter output. Results showed that, the output power of solar module is optimized and controlled by using fuzzy logic controller. Besides that, the three-phase induction motor can be drive and control using VSI switching by the PWM signal generated by the fuzzy logic controller. This concluded that the non-linear system can be controlled and used in driving three-phase induction motor.

  8. The Chaotic-Based Control of Three-Port Isolated Bidirectional DC/DC Converters for Electric and Hybrid Vehicles

    Directory of Open Access Journals (Sweden)

    Zheng Wang

    2016-01-01

    Full Text Available Three-port isolated (TPI bidirectional DC/DC converters have three energy ports and offer advantages of large voltage gain, galvanic isolation ability and high power density. For this reason this kind of converters are suitable to connect different energy sources and loads in electric and hybrid vehicles. The purpose of this paper is to propose chaotic modulation and the related control scheme for TPI bidirectional DC/DC converters, in such a way that the switching harmonic peaks can be suppressed in spectrum and the conducted electromagnetic interference (EMI is reduced. Two chaotic modulation strategies, namely the continuously chaotic modulation and the discretely chaotic modulation are presented. These two chaotic modulation strategies are applied for TPI bidirectional DC/DC converters with shifted-phase angle based control and phase-shifted PWM control. Both simulation and experiments are given to verify the validity of the proposed chaotic modulation-based control schemes.

  9. The value added of conducting regional versus local stakeholder involvement in evaluating technology acceptance

    International Nuclear Information System (INIS)

    McCabe, G.H.

    1995-06-01

    Battelle has conducted a three-year effort, funded by the U. S Department of Energy's (DOE) Office of Technology Development, to involve stakeholders in evaluating innovative technologies to clean up volatile organic compound (VOC) contamination at arid sites. Stakeholders have been encouraged to participate in the demonstration of these innovative technologies in order to improve decisions made by DOE and its contractors about technology development, demonstration, and deployment. The basic approach is to identify people and organizations with a stake in the remediation process, and hence in the demonstration of innovative technologies. Stakeholders have included public interest group and environmental group representatives, regulators, technology users, Native Americans, Hispanic community members, and local elected officials. These people are invited to be involved and they are presented with substantive information about the technologies. Their input in terms of identifying issues and concerns, defining the kinds of information needed from the demonstrations, and assessing the acceptability of the technologies for deployment, will help ensure that only broadly promising technologies are carried forward. This approach is designed to increase the likelihood of successful deployment of the new technologies needed to accomplish environmental restoration throughout the DOE complex and at private facilities. The hypothesis in conducting this regional stakeholder involvement program is that there will be different data requirements for different sites due to geographical, institutional, programmatic, and cultural differences at the sites. Identifying the broadest set of data requirements, collecting this information during the technology demonstration, and providing the results of the demonstration to stakeholders will enhance the acceptance of the technology at these sites and, thereby, enhance the technology's deployability

  10. Nonlinear Tracking Control of a Conductive Supercoiled Polymer Actuator.

    Science.gov (United States)

    Luong, Tuan Anh; Cho, Kyeong Ho; Song, Min Geun; Koo, Ja Choon; Choi, Hyouk Ryeol; Moon, Hyungpil

    2018-04-01

    Artificial muscle actuators made from commercial nylon fishing lines have been recently introduced and shown as a new type of actuator with high performance. However, the actuators also exhibit significant nonlinearities, which make them difficult to control, especially in precise trajectory-tracking applications. In this article, we present a nonlinear mathematical model of a conductive supercoiled polymer (SCP) actuator driven by Joule heating for model-based feedback controls. Our efforts include modeling of the hysteresis behavior of the actuator. Based on nonlinear modeling, we design a sliding mode controller for SCP actuator-driven manipulators. The system with proposed control law is proven to be asymptotically stable using the Lyapunov theory. The control performance of the proposed method is evaluated experimentally and compared with that of a proportional-integral-derivative (PID) controller through one-degree-of-freedom SCP actuator-driven manipulators. Experimental results show that the proposed controller's performance is superior to that of a PID controller, such as the tracking errors are nearly 10 times smaller compared with those of a PID controller, and it is more robust to external disturbances such as sensor noise and actuator modeling error.

  11. 40 CFR 81.63 - Metropolitan Fort Smith Interstate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Metropolitan Fort Smith Interstate Air... Air Quality Control Regions § 81.63 Metropolitan Fort Smith Interstate Air Quality Control Region. The Metropolitan Fort Smith Interstate Air Quality Control Region (Arkansas-Oklahoma) has been revised to consist...

  12. Female adolescents with severe substance and conduct problems have substantially less brain gray matter volume.

    Directory of Open Access Journals (Sweden)

    Manish S Dalwani

    Full Text Available Structural neuroimaging studies have demonstrated lower regional gray matter volume in adolescents with severe substance and conduct problems. These research studies, including ours, have generally focused on male-only or mixed-sex samples of adolescents with conduct and/or substance problems. Here we compare gray matter volume between female adolescents with severe substance and conduct problems and female healthy controls of similar ages.Female adolescents with severe substance and conduct problems will show significantly less gray matter volume in frontal regions critical to inhibition (i.e. dorsolateral prefrontal cortex and ventrolateral prefrontal cortex, conflict processing (i.e., anterior cingulate, valuation of expected outcomes (i.e., medial orbitofrontal cortex and the dopamine reward system (i.e. striatum.We conducted whole-brain voxel-based morphometric comparison of structural MR images of 22 patients (14-18 years with severe substance and conduct problems and 21 controls of similar age using statistical parametric mapping (SPM and voxel-based morphometric (VBM8 toolbox. We tested group differences in regional gray matter volume with analyses of covariance, adjusting for age and IQ at p<0.05, corrected for multiple comparisons at whole-brain cluster-level threshold.Female adolescents with severe substance and conduct problems compared to controls showed significantly less gray matter volume in right dorsolateral prefrontal cortex, left ventrolateral prefrontal cortex, medial orbitofrontal cortex, anterior cingulate, bilateral somatosensory cortex, left supramarginal gyrus, and bilateral angular gyrus. Considering the entire brain, patients had 9.5% less overall gray matter volume compared to controls.Female adolescents with severe substance and conduct problems in comparison to similarly aged female healthy controls showed substantially lower gray matter volume in brain regions involved in inhibition, conflict processing, valuation

  13. Comparison of chemical constituents and antimicrobial activities of three essential oils from three different brands' clove samples collected from Gulf region

    Directory of Open Access Journals (Sweden)

    Mohammad Amzad Hossain

    2014-08-01

    Full Text Available Objective: To analyze three essential oils isolated from three different brands' clove samples collected from Gulf region and tested their antimicrobial activities. Methods: The essential oils were isolated from powder clove samples by water distillation method and analyzed and identified by gas chromatography-mass spectrometry. Antimicrobial activities of the three isolated essential oils were calculated on the diameter inhibition zone by disc diffusion method against three bacterial strains with amoxicillin standard. Results: Twenty-eight, twenty-two and twenty-six chemical ingredients with high percentage were characterized based on gas chromatography retention time from clove essential oils collected from Saudi Arabia, United Arab Emirate and Jordan. The highest antimicrobial activity was obtained from Saudi Arab against Escherichia coli, Pseudomonus aeruginosa and Staphylococcus aureus and the lowest was from Jordan and the order of antimicrobial activity was Saudi Arabia>United Arab Emirate>Jordan. Conclusions: All three essential oils from Gulf region are containing very portent chemical ingredients and it could be used as medicine or antibiotics for different aliments.

  14. Anelastic spherical dynamos with radially variable electrical conductivity

    Science.gov (United States)

    Dietrich, W.; Jones, C. A.

    2018-05-01

    A series of numerical simulations of the dynamo process operating inside gas giant planets has been performed. We use an anelastic, fully nonlinear, three-dimensional, benchmarked MHD code to evolve the flow, entropy and magnetic field. Our models take into account the varying electrical conductivity, high in the ionised metallic hydrogen region, low in the molecular outer region. Our suite of electrical conductivity profiles ranges from Jupiter-like, where the outer hydrodynamic region is quite thin, to Saturn-like, where there is a thick non-conducting shell. The rapid rotation leads to the formation of two distinct dynamical regimes which are separated by a magnetic tangent cylinder - mTC. Outside the mTC there are strong zonal flows, where Reynolds stress balances turbulent viscosity, but inside the mTC Lorentz force reduces the zonal flow. The dynamic interaction between both regions induces meridional circulation. We find a rich diversity of magnetic field morphologies. There are Jupiter-like steady dipolar fields, and a belt of quadrupolar dominated dynamos spanning the range of models between Jupiter-like and Saturn-like conductivity profiles. This diversity may be linked to the appearance of reversed sign helicity in the metallic regions of our dynamos. With Saturn-like conductivity profiles we find models with dipolar magnetic fields, whose axisymmetric components resemble those of Saturn, and which oscillate on a very long time-scale. However, the non-axisymmetric field components of our models are at least ten times larger than those of Saturn, possibly due to the absence of any stably stratified layer.

  15. Capillary pressure and saturation relations for supercritical CO2 and brine in sand: High-pressure Pc(Sw) controller/meter measurements and capillary scaling predictions

    Science.gov (United States)

    Tokunaga, Tetsu K.; Wan, Jiamin; Jung, Jong-Won; Kim, Tae Wook; Kim, Yongman; Dong, Wenming

    2013-08-01

    In geologic carbon sequestration, reliable predictions of CO2 storage require understanding the capillary behavior of supercritical (sc) CO2. Given the limited availability of measurements of the capillary pressure (Pc) dependence on water saturation (Sw) with scCO2 as the displacing fluid, simulations of CO2 sequestration commonly rely on modifying more familiar air/H2O and oil/H2O Pc(Sw) relations, adjusted to account for differences in interfacial tensions. In order to test such capillary scaling-based predictions, we developed a high-pressure Pc(Sw) controller/meter, allowing accurate Pc and Sw measurements. Drainage and imbibition processes were measured on quartz sand with scCO2-brine at pressures of 8.5 and 12.0 MPa (45°C), and air-brine at 21°C and 0.1 MPa. Drainage and rewetting at intermediate Sw levels shifted to Pc values that were from 30% to 90% lower than predicted based on interfacial tension changes. Augmenting interfacial tension-based predictions with differences in independently measured contact angles from different sources led to more similar scaled Pc(Sw) relations but still did not converge onto universal drainage and imbibition curves. Equilibrium capillary trapping of the nonwetting phases was determined for Pc = 0 during rewetting. The capillary-trapped volumes for scCO2 were significantly greater than for air. Given that the experiments were all conducted on a system with well-defined pore geometry (homogeneous sand), and that scCO2-brine interfacial tensions are fairly well constrained, we conclude that the observed deviations from scaling predictions resulted from scCO2-induced decreased wettability. Wettability alteration by scCO2 makes predicting hydraulic behavior more challenging than for less reactive fluids.

  16. Conductive polymers for controlled release and treatment of central nervous system injury

    Science.gov (United States)

    Saigal, Rajiv

    As one of the most devastating forms of neurotrauma, spinal cord injury remains a challenging clinical problem. The difficulties in treatment could potentially be resolved by better technologies for therapeutic delivery. In order to develop new approaches to treating central nervous system injury, this dissertation focused on using electrically-conductive polymers, controlled drug release, and stem cell transplantation. We first sought to enhance the therapeutic potential of neural stem cells by electrically increasing their production of neurotrophic factors (NTFs), important molecules for neuronal cell survival, differentiation, synaptic development, plasticity, and growth. We fabricated a new cell culture device for growing neural stem cells on a biocompatible, conductive polymer. Electrical stimulation via the polymer led to upregulation of NTF production by neural stem cells. This approach has the potential to enhance stem cell function while avoiding the pitfalls of genetic manipulation, possibly making stem cells more viable as a clinical therapy. Seeing the therapeutic potential of conductive polymers, we extended our studies to an in vivo model of spinal cord injury (SCI). Using a novel fabrication and extraction technique, a conductive polymer was fabricated to fit to the characteristic pathology that follows contusive SCI. Assessed via quantitative analysis of MR images, the conductive polymer significantly reduced compression of the injured spinal cord. Further characterizing astroglial and neuronal response of injured host tissue, we found significant neuronal sparing as a result of this treatment. The in vivo studies also demonstrated improved locomotor recovery mediated by a conductive polymer scaffold over a non-conductive control. We next sought to take advantage of conductive polymers for local, electronically-controlled release of drugs. Seeking to overcome reported limitations in drug delivery via polypyrrole, we first embedded drugs in poly

  17. A three-plane architectonic atlas of the rat hippocampal region.

    Science.gov (United States)

    Boccara, Charlotte N; Kjonigsen, Lisa J; Hammer, Ingvild M; Bjaalie, Jan G; Leergaard, Trygve B; Witter, Menno P

    2015-07-01

    The hippocampal region, comprising the hippocampal formation and the parahippocampal region, has been one of the most intensively studied parts of the brain for decades. Better understanding of its functional diversity and complexity has led to an increased demand for specificity in experimental procedures and manipulations. In view of the complex 3D structure of the hippocampal region, precisely positioned experimental approaches require a fine-grained architectural description that is available and readable to experimentalists lacking detailed anatomical experience. In this paper, we provide the first cyto- and chemoarchitectural description of the hippocampal formation and parahippocampal region in the rat at high resolution and in the three standard sectional planes: coronal, horizontal and sagittal. The atlas uses a series of adjacent sections stained for neurons and for a number of chemical marker substances, particularly parvalbumin and calbindin. All the borders defined in one plane have been cross-checked against their counterparts in the other two planes. The entire dataset will be made available as a web-based interactive application through the Rodent Brain WorkBench (http://www.rbwb.org) which, together with this paper, provides a unique atlas resource. © 2014 Wiley Periodicals, Inc.

  18. Observational characteristics of cloud radiative effects over three arid regions in the Northern Hemisphere

    Science.gov (United States)

    Li, Jiandong; Wang, Tianhe; Habib, Ammara

    2017-08-01

    Cloud-radiation processes play an important role in regional energy budgets and surface temperature changes over arid regions. Cloud radiative effects (CREs) are used to quantitatively measure the aforementioned climatic role. This study investigates the characteristics of CREs and their temporal variations over three arid regions in central Asia (CA), East Asia (EA), and North America (NA), based on recent satellite datasets. Our results show that the annual mean shortwave (SW) and net CREs (SWCRE and NCRE) over the three arid regions are weaker than those in the same latitudinal zone of the Northern Hemisphere. In most cold months (November-March), the longwave (LW) CRE is stronger than the SWCRE over the three arid regions, leading to a positive NCRE and radiative warming in the regional atmosphere-land surface system. The cold-season mean NCRE at the top of the atmosphere (TOA) averaged over EA is 4.1 W m-2, with a positive NCRE from November to March, and the intensity and duration of the positive NCRE is larger than that over CA and NA. The CREs over the arid regions of EA exhibit remarkable annual cycles due to the influence of the monsoon in the south. The TOA LWCRE over arid regions is closely related to the high-cloud fraction, and the SWCRE relates well to the total cloud fraction. In addition, the relationship between the SWCRE and the low-cloud fraction is good over NA because of the considerable occurrence of low cloud. Further results show that the interannual variation of TOA CREs is small over the arid regions of CA and EA, but their surface LWCREs show certain decreasing trends that correspond well to their decreasing total cloud fraction. It is suggested that combined studies of more observational cloud properties and meteorological elements are needed for indepth understanding of cloud-radiation processes over arid regions of the Northern Hemisphere.

  19. Fuzzy Logic Controlled Solar Module for Driving Three- Phase Induction Motor

    International Nuclear Information System (INIS)

    Zainal, Nurul Afiqah; Tat, Chan Sooi; Ajisman

    2016-01-01

    Renewable energy produced by solar module gives advantages for generated three- phase induction motor in remote area. But, solar module's output is uncertain and complex. Fuzzy logic controller is one of controllers that can handle non-linear system and maximum power of solar module. Fuzzy logic controller used for Maximum Power Point Tracking (MPPT) technique to control Pulse-Width Modulation (PWM) for switching power electronics circuit. DC-DC boost converter used to boost up photovoltaic voltage to desired output and supply voltage source inverter which controlled by three-phase PWM generated by microcontroller. IGBT switched Voltage source inverter (VSI) produced alternating current (AC) voltage from direct current (DC) source to control speed of three-phase induction motor from boost converter output. Results showed that, the output power of solar module is optimized and controlled by using fuzzy logic controller. Besides that, the three-phase induction motor can be drive and control using VSI switching by the PWM signal generated by the fuzzy logic controller. This concluded that the non-linear system can be controlled and used in driving three-phase induction motor. (paper)

  20. White rice consumption and risk of esophageal cancer in Xinjiang Uyghur Autonomous Region, northwest China: a case-control study

    OpenAIRE

    Tang, Li; Xu, Fenglian; Zhang, Taotao; Lei, Jun; Binns, Colin W.; Lee, Andy H.

    2015-01-01

    This study investigated the association between white rice consumption and the risk of esophageal cancer in remote northwest China, where the cancer incidence is known to be high. A case-control study was conducted during 2008?2009 in Urumqi and Shihezi, Xinjiang Uyghur Autonomous Region of China. Participants were 359 incident esophageal cancer patients and 380 hospital-based controls. Information on habitual white rice consumption was obtained by personal interview using a validated semi-qu...

  1. Computational simulation of natural circulation and rewetting experiments using the TRAC/PF1 code; Simulacao computacional dos experimentos: circulacao natural no CTE-150 e remolhamento na ITR utilizando o TRAC-PF1

    Energy Technology Data Exchange (ETDEWEB)

    Silva, J.D. da

    1994-05-01

    In this work the TRAC code was used to simulate experiments of natural circulation performed in the first Brazilian integral test facility at (COPESP), Sao Paulo and a rewetting experiment in a single tube test section carried out at CDTN, Belo Horizonte, Brazil. In the first simulation the loop behavior in two transient conditions with different thermal power, namely 20 k W and 120 k W, was verified in the second one the quench front propagation, the liquid mass collected in the carry over measuring tube and the wall temperature at different elevations during the flooding experiment was measured. A comparative analysis, for code consistency, shows a good agreement between the code results and experimental data, except for the quench from velocity. (author). 15 refs, 19 figs, 12 tabs.

  2. Taking Action on Air Pollution Control in the Beijing-Tianjin-Hebei (BTH) Region: Progress, Challenges and Opportunities

    Science.gov (United States)

    Wang, Li; Zhang, Fengying; Pilot, Eva; Yu, Jie; Holdaway, Jennifer; Yang, Linsheng; Li, Yonghua; Wang, Wuyi; Vardoulakis, Sotiris; Krafft, Thomas

    2018-01-01

    Due to rapid urbanization, industrialization and motorization, a large number of Chinese cities are affected by heavy air pollution. In order to explore progress, remaining challenges, and sustainability of air pollution control in the Beijing-Tianjin-Hebei (BTH) region after 2013, a mixed method analysis was undertaken. The quantitative analysis comprised an overview of air quality management in the BTH region. Semi-structured expert interviews were conducted with 12 stakeholders from various levels of government and research institutions who played substantial roles either in decision-making or in research and advising on air pollution control in the BTH region. The results indicated that with the stringent air pollution control policies, the air quality in BTH meets the targets of the Air Pollution Prevention and Control Action Plan. However, improvements vary across the region and for different pollutants. Although implementation has been decisive and was at least in parts effectively enforced, significant challenges remained with regard to industrial and traffic emission control, and national air quality limits continued to be significantly exceeded and competing development interests remained mainly unsolved. There were also concerns about the sustainability of the current air pollution control measures especially for industries due to the top-down enforcement, and the associated large burden of social cost including unemployment and social inequity resulting industrial restructuring. Better mechanisms for ensuring cross-sectoral coordination and for improved central-local government communication were suggested. Further suggestions were provided to improve the conceptual design and effective implementation of respective air pollution control strategies in BTH. Our study highlights some of the major hurdles that need to be addressed to succeed with a comprehensive air pollution control management for the Chinese mega-urban agglomerations. PMID:29425189

  3. Taking Action on Air Pollution Control in the Beijing-Tianjin-Hebei (BTH) Region: Progress, Challenges and Opportunities.

    Science.gov (United States)

    Wang, Li; Zhang, Fengying; Pilot, Eva; Yu, Jie; Nie, Chengjing; Holdaway, Jennifer; Yang, Linsheng; Li, Yonghua; Wang, Wuyi; Vardoulakis, Sotiris; Krafft, Thomas

    2018-02-09

    Due to rapid urbanization, industrialization and motorization, a large number of Chinese cities are affected by heavy air pollution. In order to explore progress, remaining challenges, and sustainability of air pollution control in the Beijing-Tianjin-Hebei (BTH) region after 2013, a mixed method analysis was undertaken. The quantitative analysis comprised an overview of air quality management in the BTH region. Semi-structured expert interviews were conducted with 12 stakeholders from various levels of government and research institutions who played substantial roles either in decision-making or in research and advising on air pollution control in the BTH region. The results indicated that with the stringent air pollution control policies, the air quality in BTH meets the targets of the Air Pollution Prevention and Control Action Plan. However, improvements vary across the region and for different pollutants. Although implementation has been decisive and was at least in parts effectively enforced, significant challenges remained with regard to industrial and traffic emission control, and national air quality limits continued to be significantly exceeded and competing development interests remained mainly unsolved. There were also concerns about the sustainability of the current air pollution control measures especially for industries due to the top-down enforcement, and the associated large burden of social cost including unemployment and social inequity resulting industrial restructuring. Better mechanisms for ensuring cross-sectoral coordination and for improved central-local government communication were suggested. Further suggestions were provided to improve the conceptual design and effective implementation of respective air pollution control strategies in BTH. Our study highlights some of the major hurdles that need to be addressed to succeed with a comprehensive air pollution control management for the Chinese mega-urban agglomerations.

  4. Taking Action on Air Pollution Control in the Beijing-Tianjin-Hebei (BTH Region: Progress, Challenges and Opportunities

    Directory of Open Access Journals (Sweden)

    Li Wang

    2018-02-01

    Full Text Available Due to rapid urbanization, industrialization and motorization, a large number of Chinese cities are affected by heavy air pollution. In order to explore progress, remaining challenges, and sustainability of air pollution control in the Beijing-Tianjin-Hebei (BTH region after 2013, a mixed method analysis was undertaken. The quantitative analysis comprised an overview of air quality management in the BTH region. Semi-structured expert interviews were conducted with 12 stakeholders from various levels of government and research institutions who played substantial roles either in decision-making or in research and advising on air pollution control in the BTH region. The results indicated that with the stringent air pollution control policies, the air quality in BTH meets the targets of the Air Pollution Prevention and Control Action Plan. However, improvements vary across the region and for different pollutants. Although implementation has been decisive and was at least in parts effectively enforced, significant challenges remained with regard to industrial and traffic emission control, and national air quality limits continued to be significantly exceeded and competing development interests remained mainly unsolved. There were also concerns about the sustainability of the current air pollution control measures especially for industries due to the top-down enforcement, and the associated large burden of social cost including unemployment and social inequity resulting industrial restructuring. Better mechanisms for ensuring cross-sectoral coordination and for improved central-local government communication were suggested. Further suggestions were provided to improve the conceptual design and effective implementation of respective air pollution control strategies in BTH. Our study highlights some of the major hurdles that need to be addressed to succeed with a comprehensive air pollution control management for the Chinese mega-urban agglomerations.

  5. Automatic control and detector for three-terminal resistance measurement

    Science.gov (United States)

    Fasching, George E.

    1976-10-26

    A device is provided for automatic control and detection in a three-terminal resistance measuring instrument. The invention is useful for the rapid measurement of the resistivity of various bulk material with a three-terminal electrode system. The device maintains the current through the sample at a fixed level while measuring the voltage across the sample to detect the sample resistance. The three-electrode system contacts the bulk material and the current through the sample is held constant by means of a control circuit connected to a first of the three electrodes and works in conjunction with a feedback controlled amplifier to null the voltage between the first electrode and a second electrode connected to the controlled amplifier output. An A.C. oscillator provides a source of sinusoidal reference voltage of the frequency at which the measurement is to be executed. Synchronous reference pulses for synchronous detectors in the control circuit and an output detector circuit are provided by a synchronous pulse generator. The output of the controlled amplifier circuit is sampled by an output detector circuit to develop at an output terminal thereof a D.C. voltage which is proportional to the sample resistance R. The sample resistance is that segment of the sample between the area of the first electrode and the third electrode, which is connected to ground potential.

  6. Radioactivity levels in three regions of Costa Rica

    International Nuclear Information System (INIS)

    Mora, P.; Salazar, A.

    1995-01-01

    The establishment of the first radioactivity levels of natural radiation was carried out during the period 1991 to 1994 in three different regions of Costa Rica. The radionuclides studied belong to different soil types related to each selected region. Utilizing low level counting techniques the specific activity of the natural radioactive chains 238 U daughters, 232 Th and the element 40 K were measured for a total of 120 samples during this period. The amount of 137 Cs, a fall out radionuclide, was also studied. The average national values in Bq.kg -1 measured for 238 U were 11.66 for 214 Bi, 34.42 for 226 Ra and 10.73 for 232 Pb, for 232 Th daughters were 4.08 for 208 Tl, 9.65 for 212 Bi and 7.62 for 228 Ac. The specific activity value for 40 K was 95.14 Bq.kg -1 and for 137 Cs was 2.38 Bq.kg -1 . It is found that Costa Rica is not highly natural radioactive country and that the values for 137 Cs are well below international reported values [es

  7. Bio-edafology of the Coleoptera order, in three Colombia Natural Regions

    International Nuclear Information System (INIS)

    Camero R, Edgar; Chamorro B, Clara

    1997-01-01

    The characterization of Coleoptera families is showed to three different Colombian Natural Regions. This is given in relation with biological and environmental factors, different vegetation covers and soil uses. In addition to it, susceptible Coleoptera taxa are determined when natural conditions are disturbed. Methodically, a literature subject research was made, and Barber and Berlesse traps were used to organism extractions from superficial and under superficial soil. Horizons diversity, riches and constancy index were determined to each family. Results show different diversity, riches and constancy values to each family, as much in each natural region, such as to each soil use

  8. Dynamic clustering scheme based on the coordination of management and control in multi-layer and multi-region intelligent optical network

    Science.gov (United States)

    Niu, Xiaoliang; Yuan, Fen; Huang, Shanguo; Guo, Bingli; Gu, Wanyi

    2011-12-01

    A Dynamic clustering scheme based on coordination of management and control is proposed to reduce network congestion rate and improve the blocking performance of hierarchical routing in Multi-layer and Multi-region intelligent optical network. Its implement relies on mobile agent (MA) technology, which has the advantages of efficiency, flexibility, functional and scalability. The paper's major contribution is to adjust dynamically domain when the performance of working network isn't in ideal status. And the incorporation of centralized NMS and distributed MA control technology migrate computing process to control plane node which releases the burden of NMS and improves process efficiently. Experiments are conducted on Multi-layer and multi-region Simulation Platform for Optical Network (MSPON) to assess the performance of the scheme.

  9. ZnO Coatings with Controlled Pore Size, Crystallinity and Electrical Conductivity

    Directory of Open Access Journals (Sweden)

    Roman SCHMACK

    2016-05-01

    Full Text Available Zinc oxide is a wide bandgap semiconductor with unique optical, electrical and catalytic properties. Many of its practical applications rely on the materials pore structure, crystallinity and electrical conductivity. We report a synthesis method for ZnO films with ordered mesopore structure and tuneable crystallinity and electrical conductivity. The synthesis relies on dip-coating of solutions containing micelles of an amphiphilic block copolymer and complexes of Zn2+ ions with aliphatic ligands. A subsequent calcination at 400°C removes the template and induces crystallization of the pore walls. The pore structure is controlled by the template polymer, whereas the aliphatic ligands control the crystallinity of the pore walls. Complexes with a higher thermal stability result in ZnO films with a higher content of residual carbon, smaller ZnO crystals and therefore lower electrical conductivity. The paper discusses the ability of different types of ligands to assist in the synthesis of mesoporous ZnO and relates the structure and thermal stability of the precursor complexes to the crystallinity and electrical conductivity of the zinc oxide.DOI: http://dx.doi.org/10.5755/j01.ms.22.1.8634

  10. 40 CFR 81.76 - State of Hawaii Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 17 2010-07-01 2010-07-01 false State of Hawaii Air Quality Control... PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Designation of Air Quality Control Regions § 81.76 State of Hawaii Air Quality Control Region. The State of Hawaii Air Quality...

  11. Three Pillars for the Neural Control of Appetite.

    Science.gov (United States)

    Sternson, Scott M; Eiselt, Anne-Kathrin

    2017-02-10

    The neural control of appetite is important for understanding motivated behavior as well as the present rising prevalence of obesity. Over the past several years, new tools for cell type-specific neuron activity monitoring and perturbation have enabled increasingly detailed analyses of the mechanisms underlying appetite-control systems. Three major neural circuits strongly and acutely influence appetite but with notably different characteristics. Although these circuits interact, they have distinct properties and thus appear to contribute to separate but interlinked processes influencing appetite, thereby forming three pillars of appetite control. Here, we summarize some of the key characteristics of appetite circuits that are emerging from recent work and synthesize the findings into a provisional framework that can guide future studies.

  12. Three-Dimensional Networked Metal-Organic Frameworks with Conductive Polypyrrole Tubes for Flexible Supercapacitors.

    Science.gov (United States)

    Xu, Xingtao; Tang, Jing; Qian, Huayu; Hou, Shujin; Bando, Yoshio; Hossain, Md Shahriar A; Pan, Likun; Yamauchi, Yusuke

    2017-11-08

    Metal-organic frameworks (MOFs) with high porosity and a regular porous structure have emerged as a promising electrode material for supercapacitors, but their poor electrical conductivity limits their utilization efficiency and capacitive performance. To increase the overall electrical conductivity as well as the efficiency of MOF particles, three-dimensional networked MOFs are developed via using preprepared conductive polypyrrole (PPy) tubes as the support for in situ growth of MOF particles. As a result, the highly conductive PPy tubes that run through the MOF particles not only increase the electron transfer between MOF particles and maintain the high effective porosity of the MOFs but also endow the MOFs with flexibility. Promoted by such elaborately designed MOF-PPy networks, the specific capacitance of MOF particles has been increased from 99.2 F g -1 for pristine zeolitic imidazolate framework (ZIF)-67 to 597.6 F g -1 for ZIF-PPy networks, indicating the importance of the design of the ZIF-PPy continuous microstructure. Furthermore, a flexible supercapacitor device based on ZIF-PPy networks shows an outstanding areal capacitance of 225.8 mF cm -2 , which is far above other MOFs-based supercapacitors reported up to date, confirming the significance of in situ synthetic chemistry as well as the importance of hybrid materials on the nanoscale.

  13. Regional three-dimensional seismic velocity model of the crust and uppermost mantle of northern California

    Science.gov (United States)

    Thurber, C.; Zhang, H.; Brocher, T.; Langenheim, V.

    2009-01-01

    We present a three-dimensional (3D) tomographic model of the P wave velocity (Vp) structure of northern California. We employed a regional-scale double-difference tomography algorithm that incorporates a finite-difference travel time calculator and spatial smoothing constraints. Arrival times from earthquakes and travel times from controlled-source explosions, recorded at network and/or temporary stations, were inverted for Vp on a 3D grid with horizontal node spacing of 10 to 20 km and vertical node spacing of 3 to 8 km. Our model provides an unprecedented, comprehensive view of the regional-scale structure of northern California, putting many previously identified features into a broader regional context and improving the resolution of a number of them and revealing a number of new features, especially in the middle and lower crust, that have never before been reported. Examples of the former include the complex subducting Gorda slab, a steep, deeply penetrating fault beneath the Sacramento River Delta, crustal low-velocity zones beneath Geysers-Clear Lake and Long Valley, and the high-velocity ophiolite body underlying the Great Valley. Examples of the latter include mid-crustal low-velocity zones beneath Mount Shasta and north of Lake Tahoe. Copyright 2009 by the American Geophysical Union.

  14. Experimental study on two-phase flow natural circulation in a core catcher cooling channel for EU-APR1400 using air-water system

    Energy Technology Data Exchange (ETDEWEB)

    Song, Ki Won [Division of Advanced Nuclear Engineering, POSTECH, Pohang 790-784 (Korea, Republic of); Korea Atomic Energy Research Institute, Daejeon 34057 (Korea, Republic of); Nguyen, Thanh Hung [School of Nuclear Engineering, Purdue University, West Lafayette, IN 47906 (United States); Ha, Kwang Soon; Kim, Hwan Yeol; Song, Jinho [Korea Atomic Energy Research Institute, Daejeon 34057 (Korea, Republic of); Park, Hyun Sun [Division of Advanced Nuclear Engineering, POSTECH, Pohang 790-784 (Korea, Republic of); Revankar, Shripad T., E-mail: shripad@postech.ac.kr [Division of Advanced Nuclear Engineering, POSTECH, Pohang 790-784 (Korea, Republic of); School of Nuclear Engineering, Purdue University, West Lafayette, IN 47906 (United States); Kim, Moo Hwan [Division of Advanced Nuclear Engineering, POSTECH, Pohang 790-784 (Korea, Republic of); Korea Institute of Nuclear Safety, Daejeon 305-338 (Korea, Republic of)

    2017-05-15

    Highlights: • Two-phase flow regimes and transition behavior were observed in the coolant channel. • Test were conducted for natural circulation with air-water. • Data were obtained on flow regime, void fraction, flow rates and re-wetting time. • The data were related to a cooling capability of core catcher system. - Abstract: Ex-vessel core catcher cooling system driven by natural circulation is designed using a full scaled air-water system. A transparent half symmetric section of a core catcher coolant channel of a pressurized water reactor was designed with instrumentations for local void fraction measurement and flow visualization. Two designs of air-water top separator water tanks are studied including one with modified ‘super-step’ design which prevents gas entrainment into down-comer. In the experiment air flow rates are set corresponding to steam generation rate for given corium decay power. Measurements of natural circulation flow rate, spatial local void fraction distribution and re-wetting time near the top wall are carried out for various air flow rates which simulate boiling-induced vapor generation. Since heat transfer and critical heat flux are strongly dependent on the water mass flow rate and development of two-phase flow on the heated wall, knowledge of two-phase flow characteristics in the coolant channel is essential. Results on flow visualization showing two phase flow structure specifically near the high void accumulation regions, local void profiles, rewetting time, and natural circulation flow rate are presented for various air flow rates that simulate corium power levels. The data are useful in assessing the cooling capability of and safety of the core catcher system.

  15. Pinning-controlled synchronization of complex networks with bounded or unbounded synchronized regions

    International Nuclear Information System (INIS)

    Yan-Li, Zou; Guan-Rong, Chen

    2009-01-01

    This paper studies pinning-controlled synchronization of complex networks with bounded or unbounded synchronized regions. To study a state-feedback pinning-controlled network with N nodes, it first converts the controlled network to an extended network of N+1 nodes without controls. It is shown that the controlled synchronizability of the given network is determined by the real part of the smallest nonzero eigenvalue of the coupling matrix of its extended network when the synchronized region is unbounded; but it is determined by the ratio of the real parts of the largest and the smallest nonzero eigenvalues of the coupling matrix when the synchronized region is bounded. Both theoretical analysis and numerical simulation show that the portion of controlled nodes has no critical values when the synchronized region is unbounded, but it has a critical value when the synchronized region is bounded. In the former case, therefore, it is possible to control the network to achieve synchronization by pinning only one node. In the latter case, the network can achieve controlled synchronization only when the portion of controlled nodes is larger than the critical value. (general)

  16. Dead Zone Oscillator Control for Communication-Free Synchronization of Paralleled, Three-Phase, Current-Controlled Inverters

    Science.gov (United States)

    2016-05-11

    Current-Controlled Inverters by Midshipman 1/C Spencer C. Shabshab, USN UNITED STATES NAVAL ACADEMY...Three-Phase, Current-Controlled Inverters by Midshipman 1/C Spencer C. Shabshab United States Naval Academy Annapolis, Maryland...for Communication-Free Synchronization of Paralleled, 5a. CONTRACT NUMBER Three-Phase, Current-Controlled Inverters 5b. GRANT NUMBER 5c

  17. A fuzzy-logic antiswing controller for three-dimensional overhead cranes.

    Science.gov (United States)

    Cho, Sung-Kun; Lee, Ho-Hoon

    2002-04-01

    In this paper, a new fuzzy antiswing control scheme is proposed for a three-dimensional overhead crane. The proposed control consists of a position servo control and a fuzzy-logic control. The position servo control is used to control crane position and rope length, and the fuzzy-logic control is used to suppress load swing. The proposed control guarantees not only prompt suppression of load swing but also accurate control of crane position and rope length for simultaneous travel, traverse, and hoisting motions of the crane. Furthermore, the proposed control provides practical gain tuning criteria for easy application. The effectiveness of the proposed control is shown by experiments with a three-dimensional prototype overhead crane.

  18. Novel Topology of Three-Phase Electric Spring and Its Control

    DEFF Research Database (Denmark)

    Wang, Qingsong; Cheng, Ming; Jiang, Yunlei

    2017-01-01

    A novel topology is proposed for three-phase electric spring (TPES) to achieve specific functionalities. With respect to the existing one, the novel topology contains an additional three-phase transformer with the primaries located at the position of the non-critical three-phase load (NCL......) of the existing topology and its secondaries connected to the new three-phase NCL, thus forming a new three-phase smart load (SL). To control the novel topology, the so-called modified δ control utilized for the single-phase electric springs is extended to the three-phase case. Thanks to these solutions, TPES...

  19. Ionospheric conductivity dependence of dayside region-0, 1, and 2 field-aligned current systems: statistical study with DMSP-F7

    Directory of Open Access Journals (Sweden)

    K. Haraguchi

    2004-09-01

    Full Text Available The present study statistically examines the dependence of the intensities of dayside (MLT=8-12h large-scale field-aligned currents (FACs on the ionospheric conductance using the summary data of DMSP-F7 constructed by the procedure of Higuchi and Ohtani (2000. We have found that, in the dayside region, R1 and R0 have a higher correlation between ionospheric conductivity and FAC intensity than R2, suggesting that R0 and R1 are driven by a more voltage-like source than R2. This result is consistent with the idea that R1 and R0 are driven by the interaction between the solar wind and the open magnetospheric magnetic field. We have also found that dayside FAC intensities are latitudinally well balanced when they have a three sheet structure (R0, R1 and R2; on the other hand, for a two sheet structure (R1 and R2, the intensity of R1 is larger than that of R2, so that the net current has the polarity of R1.

  20. [Nitrogen Losses Under the Action of Different Land Use Types of Small Catchment in Three Gorges Region].

    Science.gov (United States)

    Chen, Cheng-long; Gao, Ming; Ni, Jiu-pai; Xie, De-ti; Deng, Hua

    2016-05-15

    27.51, 25.11, 27.11 mg · L⁻¹, respectively; different land use types and spatial combination ways of subcatchment had a greater influence on TN's losses concentrations, so using a reasonable way to adjust land use structure and spatial arrangement of whole catchment was an effective measure to control the source of non-point source pollution of Three Gorges Region.

  1. Harmonic Injection-Based Power Fluctuation Control of Three-Phase PV Systems under Unbalanced Grid Voltage Conditions

    Directory of Open Access Journals (Sweden)

    Nian-Cheng Zhou

    2015-02-01

    Full Text Available Unbalanced voltage will inevitably cause power and DC voltage fluctuations in a three-phase PV system. The deterioration of power quality will do great harm to the PV panels and the loads, so it is necessary to suppress the power fluctuations. This paper further explores the coefficients control strategy of PV converters under unbalanced voltage conditions, aiming to suppress power fluctuations by controlling the injection of some specific orders of current harmonics into the grid. In order to achieve this, the current reference of the PV inverter has been changed by bringing in two control coefficients, and the expression of each order of the current harmonics has been deduced. Based on the standards of PV systems, the regions from which the coefficients can be selected are determined. Then, by tuning these coefficients in the feasible regions, the output parameters (power fluctuation, current THD and odd harmonics can be controlled precisely. The model of this method is built and simulated in PSCAD/EMTDC, and as a result, it is shown that the power fluctuations can be restricted according to different power quality requirements.

  2. Load frequency control of three area interconnected hydro-thermal ...

    African Journals Online (AJOL)

    This paper present analysis on dynamic performance of Load Frequency Control (LFC) of three area interconnected hydrothermal reheat power system by the use of Artificial Intelligent and PI Controller. In the proposed scheme, control methodology developed using conventional PI controller, Artificial Neural Network ...

  3. Three Eras in Global Tobacco Control: How Global Governance Processes Influenced Online Tobacco Control Networking.

    Science.gov (United States)

    Wipfli, Heather; Chu, Kar-Hai; Lancaster, Molly; Valente, Thomas

    2016-01-01

    Online networks can serve as a platform to diffuse policy innovations and enhance global health governance. This study focuses on how shifts in global health governance may influence related online networks. We compare social network metrics (average degree centrality [AVGD], density [D] and clustering coefficient [CC]) of Globalink, an online network of tobacco control advocates, across three eras in global tobacco control governance; pre-Framework Convention on Tobacco Control (FCTC) policy transfer (1992-1998), global regime formation through the FCTC negotiations (1999-2005), and philanthropic funding through the Bloomberg Initiative (2006-2012). Prior to 1999, Globalink was driven by a handful of high-income countries (AVGD=1.908 D=0.030, CC=0.215). The FCTC negotiations (1999-2005) corresponded with a rapid uptick in the number of countries represented within Globalink and new members were most often brought into the network through relationships with regional neighbors (AVGD=2.824, D=0.021, CC=0.253). Between 2006 and 2012, the centrality of the US in the network increases significantly (AVGD=3.414, D=0.023, CC=0.310). The findings suggest that global institutionalization through WHO, as with the FCTC, can lead to the rapid growth of decentralized online networks. Alternatively, private initiatives, such as the Bloomberg Initiative, can lead to clustering in which a single source of information gains increasing influence over an online network.

  4. Calculation of three-dimensional MHD equilibria with islands and stochastic regions

    International Nuclear Information System (INIS)

    Reiman, A.; Greenside, H.

    1986-08-01

    A three-dimensional MHD equilibrium code is described that does not assume the existence of good surfaces. Given an initial guess for the magnetic field, the code proceeds by calculating the pressure-driven current and then by updating the field using Ampere's law. The numerical algorithm to solve the magnetic differential equation for the pressure-driven current is described, and demonstrated for model fields having islands and stochastic regions. The numerical algorithm which solves Ampere's law in three dimensions is also described. Finally, the convergence of the code is illustrated for a particular stellarator equilibrium with no large islands

  5. Quenching of hot wall of vertical-narrow-annular passages by water falling down counter-currently

    International Nuclear Information System (INIS)

    Koizumi, Yasuo; Ohtake, Hiroyasu; Arai, Manabu; Okabayashi, Yoshiaki; Nagae, Takashi; Okano, Yukimitsu

    2004-01-01

    quenching of a thin-gap annular flow passage by gravitational liquid penetration was examined by using water. The outer wall of the test flow channel was made of stainless steel. The inner wall was made of glass or stainless steel. The annular gap spacings tested were 10, 5.0, 2.0, 1.0 and 0.5 mm. No inner wall case; the gap width = ∞, was also tested. The stainless steel walls(s) was (were) heated electrically. When the glass wall was used for the inner wall, a fiber scope was inserted inside to observe a flow state. The quenching was observed for the gap spacing over 1.0 mm. When the spacing was less than 1.0 mm, the wall was gradually and monotonously cooled down without any quenching. As the gap spacing became narrow, the counter-current flow limiting; flooding, severely occurred. The peak heat flux during the quenching process became lower than that in pool boiling as the gap spacing became narrower. The quenching propagated from the bottom when the gap spacing was larger than 5 mm. When the gap clearance was less than 2.0 mm, the quenching proceeded from the top in the bottom closed case. It was visually observed that liquid accumulated in the lower portion of the flow passage in the 5 mm gap case and the rewetting front propagated upward from the bottom. In the 1.0 mm gap case, the moving-down of the rewetting front was observed. The quenching velocity became slow as the gap spacing became narrow. Quenching simulation was performed by solving a transient heat conduction equation. The simulation indicated that the quenching velocity becomes fast as the peak heat flux becomes low with the gap spacing, which was opposite to the experimental results. It was also suggested that precursory cooling is one of key factors to control the rewetting velocity; as the precursory cooling becomes weak, the rewetting velocity becomes slow. (author)

  6. F-region Pedersen conductivity deduced using the TIMED/GUVI limb retrievals

    Directory of Open Access Journals (Sweden)

    Y. Zhang

    2006-07-01

    Full Text Available As a proxy of the Rayleigh-Taylor instability growth rate for equatorial plasma bubbles, we investigate the flux-tube integrated F-region Pedersen conductivity (ΣPF using the electron density profiles (EDPs provided by the Global Ultraviolet Imager (GUVI on board the Thermosphere Ionosphere and Mesosphere Energetics and Dynamics (TIMED satellite. The investigation is conducted using the EDPs obtained in the Atlantic sector at 19:00-22:00 LT during 4–17 August and 6-16 December 2002. The seasonal difference of the strength and location of the equatorial ionization anomalies (EIAs induces a significant difference in the deduced ΣPF. Much stronger EIAs are created at higher altitudes and latitudes in December rather than in August. At 19:00–20:00 LT, the peak value of the ΣPF has 23 mhos at 1100 km apex height during 14–16 December and 18mhos at 600 km during 15–17 August. The ΣPF decreases as local time progresses. Therefore, ΣPF provides a preferred condition for the growth of bubbles to higher altitudes at 19:00-20:00 LT than at later hours, in December rather than in August in the Atlantic sector.

  7. City-specific vehicle emission control strategies to achieve stringent emission reduction targets in China's Yangtze River Delta region.

    Science.gov (United States)

    Zhang, Shaojun; Wu, Ye; Zhao, Bin; Wu, Xiaomeng; Shu, Jiawei; Hao, Jiming

    2017-01-01

    The Yangtze River Delta (YRD) region is one of the most prosperous and densely populated regions in China and is facing tremendous pressure to mitigate vehicle emissions and improve air quality. Our assessment has revealed that mitigating vehicle emissions of NOx would be more difficult than reducing the emissions of other major vehicular pollutants (e.g., CO, HC and PM 2.5 ) in the YRD region. Even in Shanghai, where the emission control implemented are more stringent than in Jiangsu and Zhejiang, we observed little to no reduction in NOx emissions from 2000 to 2010. Emission-reduction targets for HC, NOx and PM 2.5 are determined using a response surface modeling tool for better air quality. We design city-specific emission control strategies for three vehicle-populated cities in the YRD region: Shanghai and Nanjing and Wuxi in Jiangsu. Our results indicate that even if stringent emission control consisting of the Euro 6/VI standards, the limitation of vehicle population and usage, and the scrappage of older vehicles is applied, Nanjing and Wuxi will not be able to meet the NOx emissions target by 2020. Therefore, additional control measures are proposed for Nanjing and Wuxi to further mitigate NOx emissions from heavy-duty diesel vehicles. Copyright © 2016. Published by Elsevier B.V.

  8. State and Regional Control of Geological Carbon Sequestration

    Energy Technology Data Exchange (ETDEWEB)

    Reitze, Arnold [Univ. of Utah, Salt Lake City, UT (United States); Durrant, Marie [Univ. of Utah, Salt Lake City, UT (United States)

    2011-03-01

    The United States has economically recoverable coal reserves of about 261 billion tons, which is in excess of a 250-­year supply based on 2009 consumption rates. However, in the near future the use of coal may be legally restricted because of concerns over the effects of its combustion on atmospheric carbon dioxide concentrations. Carbon capture and geologic sequestration offer one method to reduce carbon emissions from coal and other hydrocarbon energy production. While the federal government is providing increased funding for carbon capture and sequestration, recent congressional legislative efforts to create a framework for regulating carbon emissions have failed. However, regional and state bodies have taken significant actions both to regulate carbon and facilitate its capture and sequestration. This article explores how regional bodies and state government are addressing the technical and legal problems that must be resolved in order to have a viable carbon sequestration program. Several regional bodies have formed regulations and model laws that affect carbon capture and storage, and three bodies comprising twenty-three states—the Regional Greenhouse Gas Initiative, the Midwest Regional Greenhouse Gas Reduction Accord, and the Western Climate initiative—have cap-­and-trade programs in various stages of development. State property, land use and environmental laws affect the development and implementation of carbon capture and sequestration projects, and unless federal standards are imposed, state laws on torts and renewable portfolio requirements will directly affect the liability and viability of these projects. This paper examines current state laws and legislative efforts addressing carbon capture and sequestration.

  9. Physical region for three-neutrino mixing angles

    Science.gov (United States)

    Latimer, D. C.; Ernst, D. J.

    2005-01-01

    We derive a set of symmetry relations for the three-neutrino mixing angles, including the Mikheyev-Smirnov-Wolfenstein (MSW) matter effect. Though interesting in their own right, these relations are used to choose the physical region of the mixing angles such that oscillations are parametrized completely and uniquely. We propose that the preferred way of setting the bounds on the mixing angles should be θ12∈[0,π/2], θ13∈[-π/2,π/2], θ23∈[0,π/2], and δ∈[0,π). No CP violation then results simply from setting δ=0. In the presence of the MSW effect, this choice of bounds is a new result. Since the size of the asymmetry about θ13=0 is dependent on the details of the data analysis and is a part of the results of the analysis, we argue that the negative values of θ13 should not be ignored.

  10. Association of genetic variations in the mitochondrial DNA control region with presbycusis.

    Science.gov (United States)

    Falah, Masoumeh; Farhadi, Mohammad; Kamrava, Seyed Kamran; Mahmoudian, Saeid; Daneshi, Ahmad; Balali, Maryam; Asghari, Alimohamad; Houshmand, Massoud

    2017-01-01

    The prominent role of mitochondria in the generation of reactive oxygen species, cell death, and energy production contributes to the importance of this organelle in the intracellular mechanism underlying the progression of the common sensory disorder of the elderly, presbycusis. Reduced mitochondrial DNA (mtDNA) gene expression and coding region variation have frequently been reported as being associated with the development of presbycusis. The mtDNA control region regulates gene expression and replication of the genome of this organelle. To comprehensively understand of the role of mitochondria in the progression of presbycusis, we compared variations in the mtDNA control region between subjects with presbycusis and controls. A total of 58 presbycusis patients and 220 control subjects were enrolled in the study after examination by the otolaryngologist and audiology tests. Variations in the mtDNA control region were investigated by polymerase chain reaction and Sanger sequencing. A total of 113 sequence variants were observed in mtDNA, and variants were detected in 100% of patients, with 84% located in hypervariable regions. The frequencies of the variants, 16,223 C>T, 16,311 T>C, 16,249 T>C, and 15,954 A>C, were significantly different between presbycusis and control subjects. The statistically significant difference in the frequencies of four nucleotide variants in the mtDNA control region of presbycusis patients and controls is in agreement with previous experimental evidence and supports the role of mitochondria in the intracellular mechanism underlying presbycusis development. Moreover, these variants have potential as diagnostic markers for individuals at a high risk of developing presbycusis. The data also suggest the possible presence of changes in the mtDNA control region in presbycusis, which could alter regulatory factor binding sites and influence mtDNA gene expression and copy number.

  11. Measures for regional security and arms control in the South-East Asian area

    International Nuclear Information System (INIS)

    Uren, R.T.

    1992-01-01

    The subject of regional security and arms control in the South-East Asia raises some new and difficult issues. No approach to ensuring regional security could be complete without military dimension including the following categories: regional arms control; global arms control measure; confidence building measures that are designed to enhance the transparency of defense policies; confidence building measures that encourage cooperation among the military forces in the region

  12. Controlling a Four-Quadrant Brushless Three-Phase dc Motor

    Science.gov (United States)

    Nola, F. J.

    1986-01-01

    Control circuit commutates windings of brushless, three-phase, permanent-magnet motor operating from power supply. With single analog command voltage, controller makes motor accelerate, drive steadily, or brake regeneratively, in clockwise or counterclockwise direction. Controller well suited for use with energy-storage flywheels, actuators for aircraft-control surfaces, cranes, industrial robots, and other electromechanical systems requiring bidirectional control or sudden stopping and reversal.

  13. Current situation, genetic relationship and control measures of infectious bronchitis virus variants circulating in African regions

    Directory of Open Access Journals (Sweden)

    Khadija Khataby

    2016-08-01

    Three S1 gene hypervariable regions were studied and compared to the reference genotypes/serotypes that found emerging in African regions. This comparison was based on phylogenetic trees, nucleotide and amino-acid sequence analysis. It clearly appears that IBV variants reported in Africa, display a low genetic relationship between them and with the majority of the reference strains emerging in neighboring countries, except the case of variants from Libya and Egypt that show a high relatedness. Also the Massachusetts serotypes were the most prevalent co-circulating with both serotypes, Italy02 type in Morocco and Qx-like genotype in South part of the African continent. In order to control the IBV variants in African regions, an efficient vaccination strategy program should be implemented.

  14. Lymphatic filariasis control in Tanga Region, Tanzania

    DEFF Research Database (Denmark)

    Simonsen, Paul Erik; Derua, Yahya A.; Magesa, Stephen M.

    2014-01-01

    BackgroundLymphatic filariasis (LF) control started in Tanga Region of Tanzania in 2004, with annual ivermectin/albendazole mass drug administration (MDA). Since then, the current project has monitored the effect in communities and schools in rural areas of Tanga District. In 2013, after 8 rounds...

  15. Family Food Providers’ Perceptions of the Causes of Obesity and Effectiveness of Weight Control Strategies in Five Countries in the Asia Pacific Region: A Cross-Sectional Survey

    Directory of Open Access Journals (Sweden)

    Anthony Worsley

    2017-01-01

    Full Text Available The rise of the middle classes in developing countries and the associated epidemiological transition raises the importance of assessing this population group’s awareness of the causes of obesity and effective weight control strategies in order to develop effective health promotion strategies. The study aimed to examine the perceptions of the causes of obesity and weight control strategies held by middle class household food providers in Melbourne, Singapore, Shanghai, Indonesia and Vietnam. An online survey was conducted in late 2013, early 2014 among 3945 respondents. Information about body weight concerns, perceived causes of obesity, effectiveness of weight control methods, demographics, self-reported height and weight, and personal values was elicited. Confirmatory factor analyses (CFA derived nine reliable factors which were used in structural equation modelling (SEM. Two thirds of respondents were trying to change their body weight, of them, 71% were trying to lose weight. The CFA and SEM showed that demographics, region of residence, personal values and perceptions of the causes of obesity (Unhealthy food behaviours, influences Beyond personal control and Environmental influences had direct and indirect associations with three weight control methods factors, named: Healthy habits, Eat less, sit less, and Dieting. Middle class food providers in the study regions share public health views of obesity causation and personal weight control. These findings could inform public health and food policies, and the design of public health interventions and communications. Further research is required among lower socio economic status (SES populations.

  16. Family Food Providers' Perceptions of the Causes of Obesity and Effectiveness of Weight Control Strategies in Five Countries in the Asia Pacific Region: A Cross-Sectional Survey.

    Science.gov (United States)

    Worsley, Anthony; Wang, Wei; Sarmugam, Rani; Pham, Quynh; Februhartanty, Judhiastuty; Ridley, Stacey

    2017-01-18

    The rise of the middle classes in developing countries and the associated epidemiological transition raises the importance of assessing this population group's awareness of the causes of obesity and effective weight control strategies in order to develop effective health promotion strategies. The study aimed to examine the perceptions of the causes of obesity and weight control strategies held by middle class household food providers in Melbourne, Singapore, Shanghai, Indonesia and Vietnam. An online survey was conducted in late 2013, early 2014 among 3945 respondents. Information about body weight concerns, perceived causes of obesity, effectiveness of weight control methods, demographics, self-reported height and weight, and personal values was elicited. Confirmatory factor analyses (CFA) derived nine reliable factors which were used in structural equation modelling (SEM). Two thirds of respondents were trying to change their body weight, of them, 71% were trying to lose weight. The CFA and SEM showed that demographics, region of residence, personal values and perceptions of the causes of obesity ( Unhealthy food behaviours , influences Beyond personal control and Environmental influences ) had direct and indirect associations with three weight control methods factors, named: Healthy habits, Eat less, sit less , and Dieting. Middle class food providers in the study regions share public health views of obesity causation and personal weight control. These findings could inform public health and food policies, and the design of public health interventions and communications. Further research is required among lower socio economic status (SES) populations.

  17. Determinants of immigrants’ entry to homeownership in three Nordic capital city regions

    DEFF Research Database (Denmark)

    Kauppinen, Timo; Andersen, Hans Skifter; Hedman, Lina

    2015-01-01

    is not only a function of differences in economic resources. These studies have largely focused on Anglo-American contexts, using mostly cross-sectional data. We apply survival analysis methods to analyse the determinants of entry to homeownership in the capital regions of three Nordic countries – Denmark...

  18. Three-dimensional closed-loop control of self-propelled microjets

    NARCIS (Netherlands)

    Khalil, I.S.M.; Magdanz, Veronika; Schmidt, Oliver S.; Sanchez, Samuel; Misra, Sarthak

    2013-01-01

    We demonstrate precise closed-loop control of microjets under the influence of the magnetic fields in three-dimensional (3D) space. For this purpose, we design a magnetic-based control system that directs the field lines towards reference positions. Microjets align along the controlled field lines

  19. Nonlinear H∞ Optimal Control Scheme for an Underwater Vehicle with Regional Function Formulation

    Directory of Open Access Journals (Sweden)

    Zool H. Ismail

    2013-01-01

    Full Text Available A conventional region control technique cannot meet the demands for an accurate tracking performance in view of its inability to accommodate highly nonlinear system dynamics, imprecise hydrodynamic coefficients, and external disturbances. In this paper, a robust technique is presented for an Autonomous Underwater Vehicle (AUV with region tracking function. Within this control scheme, nonlinear H∞ and region based control schemes are used. A Lyapunov-like function is presented for stability analysis of the proposed control law. Numerical simulations are presented to demonstrate the performance of the proposed tracking control of the AUV. It is shown that the proposed control law is robust against parameter uncertainties, external disturbances, and nonlinearities and it leads to uniform ultimate boundedness of the region tracking error.

  20. Modeling and inverse feedforward control for conducting polymer actuators with hysteresis

    International Nuclear Information System (INIS)

    Wang, Xiangjiang; Alici, Gursel; Tan, Xiaobo

    2014-01-01

    Conducting polymer actuators are biocompatible with a small footprint, and operate in air or liquid media under low actuation voltages. This makes them excellent actuators for macro- and micro-manipulation devices, however, their positioning ability or accuracy is adversely affected by their hysteresis non-linearity under open-loop control strategies. In this paper, we establish a hysteresis model for conducting polymer actuators, based on a rate-independent hysteresis model known as the Duhem model. The hysteresis model is experimentally identified and integrated with the linear dynamics of the actuator. This combined model is inverted to control the displacement of the tri-layer actuators considered in this study, without using any external feedback. The inversion requires an inverse hysteresis model which was experimentally identified using an inverse neural network model. Experimental results show that the position tracking errors are reduced by more than 50% when the hysteresis inverse model is incorporated into an inversion-based feedforward controller, indicating the potential of the proposed method in enabling wider use of such smart actuators. (paper)

  1. Modeling of quench front progression and heat transfer by radiation during reflooding of a tubular test section

    International Nuclear Information System (INIS)

    Clement, P.; Deruaz, R.

    1976-01-01

    Heat transfer modeling is presented in the scope of emergency core cooling. The rewetting of a hot dry wall during reflooding is a conduction-controlled phenomenon described by a model of heat-transfer coefficient. Upstream of the quench front, a two-dimensional approach involving both axial and transverse (or radial) heat conduction is discussed in view of thick walls, high quench front velocities and nucleate boiling. Downstream of the quench-front, high wall temperatures are reached so that a thermal radiation model is required to separate the different mechanisms of heat transfer. An attempt is made to consider radiation between walls, water droplets and vapor, with scattering emission and absorption of the two phases

  2. Financial analysis of brucellosis control for small-scale goat farming in the Bajío region, Mexico.

    Science.gov (United States)

    Oseguera Montiel, David; Bruce, Mieghan; Frankena, Klaas; Udo, Henk; van der Zijpp, Akke; Rushton, Jonathan

    2015-03-01

    Brucellosis is an endemic disease in small-scale goat husbandry systems in Mexico. It is a zoonosis and the economic consequences can be large, although estimates are not available for the Mexican goat sector. Our objective was to conduct a financial analysis of brucellosis control in a prominent dairy goat production area of the Bajío region, Mexico. We used three models: (1) a brucellosis transmission model at village flock level (n=1000 head), (2) a flock growth model at smallholder flock level (n=23 head) using output of model 1 and (3) cost-benefit analysis of several brucellosis control scenarios based on output of model 2. Scenarios consisted of test-and-slaughter or vaccination or a combination of both compared to the base situation (no control). The average net present values (NPV) of using vaccination over a 5-year period was 3.8 US$ (90% CI: 1.3-6.6) and 20 US$ (90% CI: 11.3-28.6) over a 10-year period per goat. The average benefit-cost ratios over a 5-year period and 10-year period were 4.3 US$ (90% CI: 2.2-6.9) and 12.3 US$ (90% CI: 7.5-17.3) per goat, respectively. For the total dairy goat population (38,462 head) of the study area (the Bajío of Jalisco and Michoacán) the NPV's over a 5-year and 10-year period were 0.15 million US$ and 0.8 million US$. However, brucellosis prevalence was predicted to remain relatively high at about 12%. Control scenarios with test-and-slaughter predicted to reduce brucellosis prevalence to less than 3%, but this produced a negative NPV over a 5-year period ranging from -31.6 to -11.1 US$ and from -31.1 to 7.5 US$ over a 10-year period. A brucellosis control campaign based on vaccination with full coverage is economically profitable for the goat dairy sector of the region although smallholders would need financial support in case test-and-slaughter is applied to reduce the prevalence more quickly. Copyright © 2014 Elsevier B.V. All rights reserved.

  3. Study on regional stratagem for coal mine disasters control and prevention in China

    Energy Technology Data Exchange (ETDEWEB)

    Shen, B.; Lei, Y. [China Coal Research Institute, Beijing (China)

    2009-09-15

    A regional strategy study was aimed at coal mine disaster control and prevention, which deepens and enriches the macro-strategy of coal mine disaster control and prevention, and provides an important support for the rapid and healthy development of China's regional coal industry. The country was divided into 4 regions: Northeast, North, South and Xinqing. In view of the regional status of coal mine disasters, the regulation and development trend of regional coal mine disasters was analysed, the outstanding problems and key factors were identified, and general thoughts on regional coal mine disaster control and prevention are put forward. 4 refs., 4 figs., 1 tab.

  4. Three-dimensional harmonic control of a nuclear reactor

    International Nuclear Information System (INIS)

    Potapenko, P.T.

    1989-01-01

    Algorithms for neutron flux control based on harmonic three-dimensional core are considered. The essence of the considered approach includes determination of harmonics amplitudes by signals self-powered detectors placed in reactor channels and reconstruction of neutron field distribution over the reactor core volume using the data obtained. Neutron field harmonic control is shown to be reduced to independent measurement and calculation of height harmonics in channels using techniques developed for channel power control

  5. Electrochemical Control of Single-Molecule Conductance by Fermi- Level Tuning and Conjugation Switching

    DEFF Research Database (Denmark)

    Baghernejad, Masoud; Zhao, Xiaotao; Ørnsø, Kristian Baruël

    2014-01-01

    ) centers, over >1 order of magnitude. For electrode potentials outside the redox-active region, the effect of the gate is simply to shift the molecular energy levels relative to the metal Fermi level. At the redox potential, the conductance changes abruptly as the AQ unit is oxidized...

  6. Efficacy of hypofractionated radiotherapy in loco-regional tumor control in breast

    International Nuclear Information System (INIS)

    Riaz, O.; Mahmood, A.; Rasul, S.; Haider, N.; Gul, S.

    2017-01-01

    Objective: To evaluate the efficacy of hypofractionated radiotherapy (HFRT) in locoregional control (LRC) in breast cancer. Study Design: Descriptive case series. Place and Duration of Study: Oncology Department of CMH Rawalpindi, from Jan 2014 to Oct 2014. Material and Methods: Fifty three female patients with histopathologically confirmed breast cancer and Eastern Cooperative Oncology Group performance status (ECOG-PS) greater than equal to 2 were enrolled in the study. These patients required post-operative radio-therapy to intact breast/ chest wall / residual breast tissue were treated using linear accelerator. Lateral/medial tangential and ipsilateral supraclavicular fields were employed to a dose of 39 Gy in 13 fractions with 6 MV photon beam. The ipsilateral axilla was also radiated if required to same dose with postero-anterior field. Scar boost was administered using 6 MeV electron beam to a dose of 7.5 Gy in 3 fractions in patients with high risk features for local recurrence like high grade, positive axillary nodes, lymphovascular invasion and close or positive surgical resection margins. Patients were followed up weekly during radio-therapy (RT) and three monthly after completion of RT for a period of 6 months. Any suspicious lesion was subjected to biopsy. Data analysis was done with the help of the Statistical Package for the Social Sciences (SPSS) version 19 software, which included descriptive analysis. Loco-regional control (LRC) and loco-regional recurrence (LRR) rates were calculated. LRC was no recurrence of tumor/tumor control in chest wall, axilla, residual breast tissue, and/or infraclavicular/supraclavicular lymph nodes. LRR was appearance of nodules / leison at local site which was biopsied and confirmed histopathologically. Results: Fifty three female patients with histopathologically confirmed breast cancer and ECOG-PS greater than equal to 2 requiring post-operative radio-therapy to intact breast/chest wall/ residual breast tissue were

  7. Forming controlled inset regions by ion implantation and laser bombardment

    International Nuclear Information System (INIS)

    Gibbons, J.F.

    1981-01-01

    A semiconductor integrated circuit structure in which the inset regions are ion implanted and laser annealed to maintain substantially the dimensions of the implantation and the method of forming inset implanted regions having controlled dimensions

  8. Control of Transboundary Movement of Radioactive Material Inadvertently Incorporated into Scrap Metal and Semi-finished Products of the Metal Recycling Industries. Results of the Meetings Conducted to Develop a Draft Code of Conduct

    International Nuclear Information System (INIS)

    2014-02-01

    In 2010, the IAEA initiated the development of a code of conduct on the transboundary movement of radioactive material inadvertently incorporated into scrap metal and semi- finished products of the metal recycling industries (Metal Recycling Code of Conduct). The Metal Recycling Code of Conduct was intended to harmonize the approaches of Member States in relation to the discovery of radioactive material that may inadvertently be present in scrap metals and semi-finished products subject to transboundary movement, and their safe handling and management to facilitate regulatory control. The Metal Recycling Code of Conduct was envisaged as being complementary to the Safety Guide on Control of Orphan Sources and Other Radioactive Material in the Metal Recycling and Production Industries (IAEA Safety Standards Series No. SSG-17), which provides recommendations, principally within a national context, on the protection of workers, members of the public and the environment in relation to the control of radioactive material inadvertently incorporated in scrap metal. In February 2013, the third open-ended meeting of technical and legal experts to develop the Metal Recycling Code of Conduct was organized. The objective of this meeting was to address the comments received from Member States and to finalize the text of the draft Metal Recycling Code of Conduct. Representatives from 55 Member States, one non-Member State and the EU, together with seven observers from the metal recycling industry, reviewed the comments and revised the draft accordingly. In September 2013, in Resolution GC(57)/RES/9, the IAEA General Conference recorded that it 'Appreciates the intensive efforts undertaken by the Secretariat to develop a code of conduct on the transboundary movement of scrap metal, or materials produced from scrap metal, that may inadvertently contain radioactive material, and encourages the Secretariat to make the results of the discussion conducted on this issue available to

  9. Control of a three-phase four-wire shunt-active power filter based on DC-bus energy regulation

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Teodorescu, Remus; Rodriguez, Pedro

    2008-01-01

    This paper presents a nonconventional three-phase four-wire shunt active power filter (APF) topology controlled by using an energy approach. A general study of power terms involved in the operation of the four-wire APF is conducted in order to evidence the relationship between instantaneous energy...... stored in the DC bus and active power requirements on the APF. Harmonics and imbalances both on the utility voltage and load current have been considered and the power developed by the active power filter has been evaluated. This study allows designing a controller for the APF based on the regulation...

  10. ANALYSIS, OPTIMAL CONTROL, AND SIMULATION OF CONDUCTIVE-RADIATIVE HEAT TRANSFER

    Directory of Open Access Journals (Sweden)

    Peter Philip

    2011-01-01

    Full Text Available This article surveys recent results regarding the existence of weaksolutions to quasilinear partial differential equations(PDEcouplednonlocally by the integral operator of the radiosity equation, modeling conductive-radiative heat transfer. Both the stationary and the transient case are considered. For the stationary case, an optimal control problem with control constraints is presented withfirst-order necessary optimality conditions, where recent results on the solution theory of the linearized state equation allow to close a previous gap.Afinite volume scheme for the discretization of the stationary system is described and, based on this scheme, a numerical computation of the temperaturefield(solution of the state equationis shown as well as the numerical solution to a realistic control problem in the context of industrial applications in crystal growth.

  11. An Optimal PR Control Strategy with Load Current Observer for a Three-Phase Voltage Source Inverter

    Directory of Open Access Journals (Sweden)

    Xiaobo Dou

    2015-07-01

    Full Text Available Inverter voltage control is an important task in the operation of a DC/AC microgrid system. To improve the inverter voltage control dynamics, traditional approaches attempt to measure and feedforward the load current, which, however, needs remote measurement with communications in a microgrid system with distributed loads. In this paper, a load current observer (LCO based control strategy, which does not need remote measurement, is proposed for sinusoidal signals tracking control of a three-phase inverter of the microgrid. With LCO, the load current is estimated precisely, acting as the feedforward of the dual-loop control, which can effectively enlarge the stability margin of the control system and improve the dynamic response to load disturbance. Furthermore, multiple PR regulators are applied in this strategy conducted in a stationary  frame to suppress the transient fluctuations and the total harmonic distortion (THD of the output voltage and achieve faster transient performance compared with traditional dual-loop control in a rotating dq0 frame under instantaneous change of various types of load (i.e., balanced load, unbalanced load, and nonlinear load. The parameters of multiple PR regulators are analyzed and selected through the root locus method and the stability of the whole control system is evaluated and analyzed. Finally, the validity of the proposed approach is verified through simulations and a three-phase prototype test system with a TMS320F28335 DSP.

  12. Force control of a tri-layer conducting polymer actuator using optimized fuzzy logic control

    International Nuclear Information System (INIS)

    Itik, Mehmet; Sabetghadam, Mohammadreza; Alici, Gursel

    2014-01-01

    Conducting polymers actuators (CPAs) are potential candidates for replacing conventional actuators in various fields, such as robotics and biomedical engineering, due to their advantageous properties, which includes their low cost, light weight, low actuation voltage and biocompatibility. As these actuators are very suitable for use in micro-nano manipulation and in injection devices in which the magnitude of the force applied to the target is of crucial importance, the force generated by CPAs needs to be accurately controlled. In this paper, a fuzzy logic (FL) controller with a Mamdani inference system is designed to control the blocking force of a trilayer CPA with polypyrrole electrodes, which operates in air. The particle swarm optimization (PSO) method is employed to optimize the controller’s membership function parameters and therefore enhance the performance of the FL controller. An adaptive neuro-fuzzy inference system model, which can capture the nonlinear dynamics of the actuator, is utilized in the optimization process. The optimized Mamdani FL controller is then implemented on the CPA experimentally, and its performance is compared with a non-optimized fuzzy controller as well as with those obtained from a conventional PID controller. The results presented indicate that the blocking force at the tip of the CPA can be effectively controlled by the optimized FL controller, which shows excellent transient and steady state characteristics but increases the control voltage compared to the non-optimized fuzzy controllers. (paper)

  13. ConductHome: Gesture Interface Control of Home Automation Boxes

    OpenAIRE

    J. Branstett; V. Gagneux; A. Leleu; B. Levadoux; J. Pascale

    2015-01-01

    This paper presents the interface ConductHome which controls home automation systems with a Leap Motion using "invariant gesture protocols". This interface is meant to simplify the interaction of the user with its environment. A hardware part allows the Leap Motion to be carried around the house. A software part interacts with the home automation box and displays the useful information for the user. An objective of this work is the development of a natural/invariant/simpl...

  14. Spatio-temporal variation of precipitation in the Three-River Headwater Region from 1961 to 2010

    Institute of Scientific and Technical Information of China (English)

    YI Xiangsheng; LI Guosheng; YIN Yanyu

    2013-01-01

    Based on a monthly dataset of precipitation time series (1961-2010) from 12 meteorological stations across the Three-River Headwater Region (THRHR) of Qinghai Province,China,the spatio-temporal variation and abrupt change analysis of precipitation were examined by using moving average,linear regression,spline interpolation,the Mann-Kendall test and so on.Major conclusions were as follows.(1) The long-term annual and seasonal precipitation in the study area indicated an increasing trend with some oscillations during 1961-2010; however,the summer precipitation in the Lantsang (Lancang) River Headwater Region (LARHR),and the autumn precipitation in the Yangtze River Headwater Region (YERHR) of the THRHR decreased in the same period.(2) The amount of annual precipitation in the THRHR and its three sub-headwater regions was greater in the 1980s and 2000s.The springs were fairly wet after the 1970s,while the summers were relatively wet in the 1960s,1980s and 2000s.In addition,the amount of precipitation in the autumn was greater in the 1970s and 1980s,but it was relatively less for the winter precipitation,except in the 1990s.(3) The normal values of spring,summer,winter and annual precipitation in the THRHR and its three sub-headwater regions all increased,but the normal value of summer precipitation in the LARHR had a negative trend and the normal value of winter precipitation declined in general.(4) The spring and winter precipitation increased in most of the THRHR.The summer,autumn and annual precipitation increased mainly in the marginal area of the west and north and decreased in the regions of Yushu,Zaduo,Jiuzhi and Banma.(5) The spring and winter precipitation in the THRHR and its three sub-headwater regions showed an abrupt change,except for the spring precipitation in the YARHR.The abrupt changes of spring precipitation were mainly in the late 1980s and early 1990s,while the abrupt changes of winter precipitation were primary in the mid-to late 1970s

  15. VOCs and OVOCs distribution and control policy implications in Pearl River Delta region, China

    Science.gov (United States)

    Louie, Peter K. K.; Ho, Josephine W. K.; Tsang, Roy C. W.; Blake, Donald R.; Lau, Alexis K. H.; Yu, Jian Zhen; Yuan, Zibing; Wang, Xinming; Shao, Min; Zhong, Liuju

    2013-09-01

    Ambient air measurements of volatile organic compounds (VOCs) and oxygenated volatile organic compounds (OVOCs) were conducted and characterised during a two-year grid study in the Pearl River Delta (PRD) region of southern China. The present grid study pioneered the systematic investigation of the nature and characteristics of complex VOC and OVOC sources at a regional scale. The largest contributing VOCs, accounting over 80% of the total VOCs mixing ratio, were toluene, ethane, ethyne, propane, ethene, butane, benzene, pentane, ethylbenzene, and xylenes. Sub-regional VOC spatial characteristics were identified, namely: i) relatively fresh pollutants, consistent with elevated vehicular and industrial activities, around the PRD estuary; and ii) a concentration gradient with higher mixing ratios of VOCs in the west as compared with the eastern part of PRD. Based on alkyl nitrate aging determination, a high hydroxyl radical (OH) concentration favoured fast hydrocarbon reactions and formation of locally produced ozone. The photochemical reactivity analysis showed aromatic hydrocarbons and alkenes together consisted of around 80% of the ozone formation potential (OFP) among the key VOCs. We also found that the OFP from OVOCs should not be neglected since their OFP contribution was more than one-third of that from VOCs alone. These findings support the choice of current air pollution control policy which focuses on vehicular sources but warrants further controls. Industrial emissions and VOCs emitted by solvents should be the next targets for ground-level ozone abatement.

  16. Association of genetic variations in the mitochondrial DNA control region with presbycusis

    Directory of Open Access Journals (Sweden)

    Falah M

    2017-03-01

    Full Text Available Masoumeh Falah,1 Mohammad Farhadi,1 Seyed Kamran Kamrava,1 Saeid Mahmoudian,1 Ahmad Daneshi,1 Maryam Balali,1 Alimohamad Asghari,2 Massoud Houshmand1,3 1ENT and Head & Neck Research Center and Department, Iran University of Medical Sciences, Tehran, Iran; 2Skull Base Research Center, Iran University of Medical Sciences, Tehran, Iran; 3Department of Medical Genetics, National Institute of Genetic Engineering and Biotechnology, Tehran, Iran Background: The prominent role of mitochondria in the generation of reactive oxygen species, cell death, and energy production contributes to the importance of this organelle in the intracellular mechanism underlying the progression of the common sensory disorder of the elderly, presbycusis. Reduced mitochondrial DNA (mtDNA gene expression and coding region variation have frequently been reported as being associated with the development of presbycusis. The mtDNA control region regulates gene expression and replication of the genome of this organelle. To comprehensively understand of the role of mitochondria in the progression of presbycusis, we compared variations in the mtDNA control region between subjects with presbycusis and controls.Methods: A total of 58 presbycusis patients and 220 control subjects were enrolled in the study after examination by the otolaryngologist and audiology tests. Variations in the mtDNA control region were investigated by polymerase chain reaction and Sanger sequencing.Results: A total of 113 sequence variants were observed in mtDNA, and variants were detected in 100% of patients, with 84% located in hypervariable regions. The frequencies of the variants, 16,223 C>T, 16,311 T>C, 16,249 T>C, and 15,954 A>C, were significantly different between presbycusis and control subjects.Conclusion: The statistically significant difference in the frequencies of four nucleotide variants in the mtDNA control region of presbycusis patients and controls is in agreement with previous experimental

  17. Control of Electronic Conduction at an Oxide Heterointerface using Surface Polar Adsorbates

    Energy Technology Data Exchange (ETDEWEB)

    Bell, Christopher

    2011-08-19

    We study the effect of the surface adsorption of a variety of common laboratory solvents on the conductivity at the interface between LaAlO{sub 3} and SrTiO{sub 3}. This interface possesses a range of intriguing physics, notably a proposed connection between the surface state of the LaAlO{sub 3} and the conductivity buried in the SrTiO{sub 3}. We show that the application of chemicals such as acetone, ethanol, and water can induce a large change (factor of three) in the conductivity. This phenomenon is observed only for polar solvents. These data provide experimental evidence for a general polarization-facilitated electronic transfer mechanism.

  18. Field Study of the Comparative Efficacy of Three Pyrethroid/Neonicotinoid Mixture Products for the Control of the Common Bed Bug, Cimex lectularius

    Directory of Open Access Journals (Sweden)

    Changlu Wang

    2015-03-01

    Full Text Available Three insecticide mixtures that contain two classes of insecticides (pyrethroid and neonicotinoid were recently developed to control bed bugs. We evaluated three integrated bed bug management strategies in apartments, each using the same non-chemical control methods and one of the three insecticide mixture products: Tandem (lambda-cyhalothrin + thiamethoxam, Temprid SC (beta-cyfluthrin + imidacloprid, and Transport Mikron (bifenthrin + acetamiprid. No insecticides were applied in the Control apartments. In all apartments, we installed vinyl mattress encasements (if not already present and applied steam to beds and other infested upholstered furniture. Insecticide sprays were applied in the three treatments. Each treatment and the Control included 8–10 occupied apartments. Re-treatment was conducted during biweekly inspections if necessary. After eight weeks, the mean (± SEM bed bug count reduction in the Tandem, Temprid SC, Transport Mikron, and Control was 89 ± 9, 87 ± 6, 98 ± 1, and 23 ± 54%, respectively. Only Tandem and Transport Mikron treatments resulted in significantly higher population reduction than the Control at eight weeks. There were no significant differences in mean percent reduction among the three treatments (Tandem, Temprid SC, Transport Mikron at eight weeks. Tandem spray caused significantly faster bed bug reduction than Temprid SC spray and Transport Mikron spray.

  19. Developments and Control of Biocompatible Conducting Polymer for Intracorporeal Continuum Robots.

    Science.gov (United States)

    Chikhaoui, Mohamed Taha; Benouhiba, Amine; Rougeot, Patrick; Rabenorosoa, Kanty; Ouisse, Morvan; Andreff, Nicolas

    2018-04-30

    Dexterity of robots is highly required when it comes to integration for medical applications. Major efforts have been conducted to increase the dexterity at the distal parts of medical robots. This paper reports on developments toward integrating biocompatible conducting polymers (CP) into inherently dexterous concentric tube robot paradigm. In the form of tri-layer thin structures, CP micro-actuators produce high strains while requiring less than 1 V for actuation. Fabrication, characterization, and first integrations of such micro-actuators are presented. The integration is validated in a preliminary telescopic soft robot prototype with qualitative and quantitative performance assessment of accurate position control for trajectory tracking scenarios. Further, CP micro-actuators are integrated to a laser steering system in a closed-loop control scheme with displacements up to 5 mm. Our first developments aim toward intracorporeal medical robotics, with miniaturized actuators to be embedded into continuum robots.

  20. Child mortality and poverty in three world regions (the West, Asia and Sub-Saharan Africa) 1988-2010: Evidence of relative intra-regional neglect?

    Science.gov (United States)

    Pritchard, Colin; Keen, Steven

    2016-12-01

    Poverty kills children. This study assesses the relationship between poverty and child mortality rates (CMRs) in 71 societies from three world regions to determine whether some countries, relative to their region, neglect their children. Spearman rank order correlations were calculated to determine any association between the CMR and poverty data, including income inequality and gross national income. A current CMR one standard deviation (SD) above or below the regional average and a percentage change between 1988 and 2010 were used as the measures to assess the progress of nations. There were positive significant correlations between higher CMRs and relative poverty measures in all three regions. In Western countries, the current CMRs in the USA, New Zealand and Canada were 1 SD below the Western mean. The narrowest income inequalities, apart from Japan, were seen in the Scandinavian nations alongside low CMRs. In Asia, the current CMRs in Pakistan, Myanmar and India were the highest in their region and were 1 SD below the regional mean. Alongside South Korea, these nations had the lowest percentage reductions in CMRs. In Sub-Saharan Africa, the current CMRs in Somalia, Burkina Faso, Sierra Leone, Chad, Democratic Republic of Congo and Angola were the highest in their region and were 1 SD below the regional mean. Those concerned with the pursuit of social justice need to alert their societies to the corrosive impact of poverty on child mortality. Progress in reducing CMRs provides an indication of how well nations are meeting the needs of their children. Further country-specific research is required to explain regional differences.

  1. The Effect of High Ambient Temperature on the Elderly Population in Three Regions of Sweden

    Directory of Open Access Journals (Sweden)

    Joacim Rocklöv

    2010-06-01

    Full Text Available The short-term effects of high temperatures are a serious concern in the context of climate change. In areas that today have mild climates the research activity has been rather limited, despite the fact that differences in temperature susceptibility will play a fundamental role in understanding the exposure, acclimatization, adaptation and health risks of a changing climate. In addition, many studies employ biometeorological indexes without careful investigation of the regional heterogeneity in the impact of relative humidity. We aimed to investigate the effects of summer temperature and relative humidity and regional differences in three regions of Sweden allowing for heterogeneity of the effect over the scale of summer temperature. To do so, we collected mortality data for ages 65+ from Stockholm, Göteborg and Skåne from the Swedish National Board of Health and Welfare and the Swedish Meteorological and Hydrological Institute for the years 1998 through 2005. In Stockholm and Skåne on average 22 deaths per day occurred, while in Göteborg the mean frequency of daily deaths was 10. We fitted time-series regression models to estimate relative risks of high ambient temperatures on daily mortality using smooth functions to control for confounders, and estimated non-linear effects of exposure while allowing for auto-regressive correlation of observations within summers. The effect of temperature on mortality was found distributed over the same or following day, with statistically significant cumulative combined relative risk of about 5.1% (CI = 0.3, 10.1 per °C above the 90th percentile of summer temperature. The effect of high relative humidity was statistically significant in only one of the regions, as was the effect of relative humidity (above 80th percentile and temperature (above 90th percentile. In the southernmost region studied there appeared to be a significant increase in mortality with decreasing low summer temperatures that was not

  2. Development of three dimensional ocean current model for coastal region

    International Nuclear Information System (INIS)

    Kobayashi, Takuya

    1999-12-01

    In order to study the migration behavior of radionuclides released into a coastal region around Japan, Princeton Ocean Model (POM) was introduced. This three-dimensional ocean current model was modified to be applied for oceanic simulations around Japan. This report describes the governing equations, numerical methods and model improvements. In addition, database system which is utilized for calculations and visualization system for graphical outputs are also described. Model simulation was carried out at off the area of Shimokita. Aomori-ken, Japan to investigate the effects of the boundary conditions on simulated results. (author)

  3. Spin-Current-Controlled Modulation of the Magnon Spin Conductance in a Three-Terminal Magnon Transistor

    Science.gov (United States)

    Cornelissen, L. J.; Liu, J.; van Wees, B. J.; Duine, R. A.

    2018-03-01

    Efficient manipulation of magnon spin transport is crucial for developing magnon-based spintronic devices. In this Letter, we provide proof of principle of a method for modulating the diffusive transport of thermal magnons in an yttrium iron garnet channel between injector and detector contacts. The magnon spin conductance of the channel is altered by increasing or decreasing the magnon chemical potential via spin Hall injection of magnons by a third modulator electrode. We obtain a modulation efficiency of 1.6 %/mA at T =250 K . Finite element modeling shows that this could be increased to well above 10 %/mA by reducing the thickness of the channel, providing interesting prospects for the development of thermal-magnon-based logic circuits.

  4. IDENTIFYING REGIONAL CLUSTER MANAGEMENT POTENTIALS EMPIRICAL RESULTS FROM THREE NORTH RHINEWESTPHALIAN REGIONS

    OpenAIRE

    Rudiger Hamm; Christiane Goebel

    2010-01-01

    The development and support of clusters is an issue that became quite popular by players dealing with regional economic policy. But before a regional development agency can start to implement a cluster-oriented strategy there a two question that have to be answered: 1. What are the regional fields of competence (cluster potentials) that fulfill the requirements for a cluster-oriented regional development policy? 2. If you find such regional fields of competence, are the enterprises willing to...

  5. Development of Tailorable Electrically Conductive Thermal Control Material Systems

    Science.gov (United States)

    Deshpande, M. S.; Harada, Y.

    1997-01-01

    The optical characteristics of surfaces on spacecraft are fundamental parameters in controlling its temperature. Passive thermal control coatings with designed solar absorptance and infrared emittance properties have been developed and have been in use for some time. In this total space environment, the coating must be stable and maintain its desired optical properties as well as mechanical properties for the course of the mission lifetime. The mission lifetimes are increasing and in our quest to save weight, newer substrates are being integrated which limit electrical grounding schemes. All of this has added to already existing concerns about spacecraft charging and related spacecraft failures or operational failures. The concern is even greater for thermal control surfaces that are very large. One way of alleviating such concerns is to design new thermal control material systems (TCMS) that can help to mitigate charging via providing charge leakage paths. The objective of this program was to develop two types of passive electrically conductive TCMS. The first was a highly absorbing/emitting black surface and the second was a low (alpha(sub s)/epsilon(sub N)) type white surface. The surface resistance goals for the black absorber was 10(exp 4) to 10(exp 9) Omega/square, and for the white surfaces it was 10(exp 6) to 10(exp 10) Omega/square. Several material system concepts were suggested and evaluated for space environment stability and electrical performance characterization. Our efforts in designing and evaluating these material systems have resulted in several developments. New concepts, pigments and binders have been developed to provide new engineering quality TCMS. Some of these have already found application on space hardware, some are waiting to be recognized by thermal designers, and some require further detailed studies to become state-of-the-art for future space hardware and space structures. Our studies on baseline state-of-the-art materials and

  6. Orifice design for the control of coupled region flow

    International Nuclear Information System (INIS)

    Atherton, R.; Spadaro, P.R.; Brummerhop, F.G.

    1975-01-01

    A fluid system arrangement for nuclear reactors is described comprising a triplate orifice apparatus which simultaneously controls core flow distribution, flow rate ratio between hydraulically coupled regions of the blanket and radial static pressure gradients entering and leaving the blanket fuel region. The design of the apparatus is based on the parameters of the diameter of the orifice holes, the friction factor, and expansion, contraction and turning pressure loss coefficients of the geometry of each orifice region. These above parameters are properly matched to provide the desired pressure drop, flow split and negligible cross flow at the interface of standard and power-flattened open lattice blanket regions. (U.S.)

  7. Arsenic content of soils from three regions of Santa Catarina State

    Directory of Open Access Journals (Sweden)

    Leticia Cristina de Souza

    2016-03-01

    Full Text Available The determination of trace elements is necessary in order to monitor their entry into the soil system and to remediate contaminated areas. The purpose of this study was to determine the natural content of arsenic (As in soils of three regions of Santa Catarina State (SC: the Southern Plateau, the Metropolitan area and the Southern Coast. Arsenic content was obtained after digestion in a microwave oven, following the USEPA 3051 A protocol and quantification was made by atomic absorption spectrometry with electrothermal atomization. The results were analyzed by the Scott-Knott test at a 5% significance level. Soil attributes that best correlated with arsenic content were clay, organic carbon, cation exchange capacity and Al and Fe oxides. The arsenic levels are related to the source material and the slope of regional soils.

  8. LH2 three-phase pump control circuit description

    International Nuclear Information System (INIS)

    Pierce, W.

    1977-05-01

    A brief description and circuit drawings are given for a pump control system. The pump is used to circulate liquid hydrogen through the cell and heat exchanger of an LH 2 target. The pump is powered by three-phase 60 cycle power, and the control unit is powered from a positive and negative 24 V dc supply available in the NIM Bin. The control unit is packaged in a double-width NIM module. Drawings are given for the pump speed indicator, function generator, and power supply

  9. Control of water infiltration into near surface LLW disposal units-progress report on field experiments at a humid region site, Beltsville, Maryland

    International Nuclear Information System (INIS)

    O'Donnell, E.; Ridky, R.W.; Schulz, R.K.

    1994-01-01

    The study's objective is to assess means for controlling water infiltration through waste disposal unit covers in humid regions. Experimental work is being performed in large-scale lysimeters (75'x45'x10') at Beltsville, MD, and results of the assessment are applicable to disposal of low-level radioactive waste (LLW), uranium mill tailings, hazardous waste, and sanitary landfills. Three kinds of waste disposal unit covers or barriers to water infiltration are being investigated. They are: (1) resistive layer barrier, (2) conductive layer barrier, and (3) bioengineering management. The conductive layer barrier consists of a conductive layer in conjunction with a capillary break. As long as unsaturated flow conditions are maintained, the conductive layer will wick water around the capillary break. Below-grade layered covers such as (1) and (2) will fail if there is appreciable subsidence of the cover. Remedial action for this kind of failure will be difficult. A surface cover, called bioengineering management, is meant to overcome this problem. The bioengineering management surface barrier is easily repairable if damaged by subsidence; therefore, it could be the system of choice under active subsidence conditions. The bioengineering management procedure also has been shown to be effective in dewatering saturated trenches and could be used for remedial action efforts. After cessation of subsidence, that procedure could be replaced by a resistive layer barrier, or perhaps even better, a resistive layer barrier/conductive layer barrier system. This latter system would then give long-term effective protection against water entry into waste and without institutional care

  10. Changing patterns in water toxicity associated with current use pesticides in three California agriculture regions.

    Science.gov (United States)

    Anderson, Brian S; Phillips, Bryn M; Voorhees, Jennifer P; Deng, Xin; Geraci, Jeff; Worcester, Karen; Tjeerdema, Ron S

    2018-03-01

    Regulation of agriculture irrigation water discharges in California, USA, is assessed and controlled by its 9 Regional Water Quality Control Boards under the jurisdiction of the California State Water Resources Control Board. Each Regional Water Board has developed programs to control pesticides in runoff as part of the waste discharge requirements implemented through each region's Irrigated Lands Regulatory Program. The present study assessed how pesticide use patterns differ in the Imperial (Imperial County) and the Salinas and Santa Maria (Monterey County) valleys, which host 3 of California's prime agriculture areas. Surface-water toxicity associated with current use pesticides was monitored at several sites in these areas in 2014 and 2015, and results were linked to changes in pesticide use patterns in these areas. Pesticide use patterns appeared to coincide with differences in the way agriculture programs were implemented by the 2 respective Regional Water Quality Control Boards, and these programs differed in the 2 Water Board Regions. Different pesticide use patterns affected the occurrence of pesticides in agriculture runoff, and this influenced toxicity test results. Greater detection frequency and higher concentrations of the organophosphate pesticide chlorpyrifos were detected in agriculture runoff in Imperial County compared to Monterey County, likely due to more rigorous monitoring requirements for growers using this pesticide in Monterey County. Monterey County agriculture runoff contained toxic concentrations of pyrethroid and neonicotinoid pesticides, which impacted amphipods (Hyalella azteca) and midge larvae (Chironomus dilutus) in toxicity tests. Study results illustrate how monitoring strategies need to evolve as regulatory actions affect change in pesticide use and demonstrate the importance of using toxicity test indicator species appropriate for the suite of contaminants in runoff in order to accurately assess environmental risk. Integr

  11. Control Mechanism and Security Region for Intentional Islanding Transition

    DEFF Research Database (Denmark)

    Chen, Yu; Xu, Zhao; Østergaard, Jacob

    2009-01-01

    in the grid. The concept of Islanding Security Region (ISR) has been proposed as an organic composition of the developed control mechanism. The purpose of this control mechanism is to maintain the frequency stability and eventually the security of power supply to the customers, by utilizing resources from...... generation and demand sides. The control mechanism can be extended to consider the distributed generations like wind power and other innovative technologies such as the Demand as Frequency controlled Reserve (DFR) technique in the future....

  12. Novel highly sensitive and wearable pressure sensors from conductive three-dimensional fabric structures

    International Nuclear Information System (INIS)

    Li, Jianfeng; Xu, Bingang

    2015-01-01

    Pressure sensors based on three-dimensional fabrics have all the excellent properties of the textile substrate: excellent compressibility, good air permeability and moisture transmission ability, which will find applications ranging from the healthcare industry to daily usage. In this paper, novel pressure sensors based on 3D spacer fabrics have been developed by a proposed multi-coating method. By this coating method, carbon black can be coated uniformly on the silicon elastomer which is attached and slightly cured on the 3D fabric surface beforehand. The as-made pressure sensors have good conductivity and can measure external pressure up to 283 kPa with an electrical conductivity range of 9.8 kΩ. The sensitivity of 3D fabric pressure sensors can be as high as 50.31×10 −3 kPa −1 , which is better than other textile based pressure sensors. When the as-made sensors are pressed, their electrical resistance will decrease because of more conductive connections and bending of fibers in the spacer layer. The sensing mechanism related to fiber bending has been explored by using an equivalent resistance model. The newly developed 3D sensor devices can be designed to exhibit different sensing performances by simply changing the structures of fabric substrate, which endows this kind of device more flexibility in related applications. (paper)

  13. Health conditions and role limitation in three European Regions: a public-health perspective.

    Science.gov (United States)

    Barbaglia, Gabriela; Adroher, Núria D; Vilagut, Gemma; Bruffaerts, Ronny; Bunting, Brentan; Caldas de Almeida, José Miguel; Florescu, Silvia; de Girolamo, Giovanni; de Graaf, Ron; Haro, Josep Maria; Hinkov, Hristo; Kovess-Masfety, Vivianne; Matschinger, Herbert; Alonso, Jordi

    To describe the distribution of role limitation in the European population aged 18-64 years and to examine the contribution of health conditions to role limitation using a public-health approach. Representative samples of the adult general population (n=13,666) aged 18-64 years from 10 European countries of the World Mental Health (WMH) Surveys Initiative, grouped into three regions: Central-Western, Southern and Central-Eastern. The Composite International Diagnostic Interview (CIDI 3.0) was used to assess six mental disorders and standard checklists for seven physical conditions. Days with full and with partial role limitation in the month previous to the interview were reported (WMH-WHODAS). Population Attributable Fraction (PAFs) of full and partial role limitation were estimated. Health conditions explained a large proportion of full role limitation (PAF=62.6%) and somewhat less of partial role limitation (46.6%). Chronic pain was the single condition that consistently contributed to explain both disability measures in all European Regions. Mental disorders were the most important contributors to full and partial role limitation in Central-Western and Southern Europe. In Central-Eastern Europe, where mental disorders were less prevalent, physical conditions, especially cardiovascular diseases, were the highest contributors to disability. The contribution of health conditions to role limitation in the three European regions studied is high. Mental disorders are associated with the largest impact in most of the regions. There is a need for mainstreaming disability in the public health agenda to reduce the role limitation associated with health conditions. The cross-regional differences found require further investigation. Copyright © 2016 SESPAS. Publicado por Elsevier España, S.L.U. All rights reserved.

  14. Catalytic, Conductive Bipolar Membrane Interfaces through Layer-by-Layer Deposition for the Design of Membrane-Integrated Artificial Photosynthesis Systems.

    Science.gov (United States)

    McDonald, Michael B; Freund, Michael S; Hammond, Paula T

    2017-11-23

    In the presence of an electric field, bipolar membranes (BPMs) are capable of initiating water disassociation (WD) within the interfacial region, which can make water splitting for renewable energy in the presence of a pH gradient possible. In addition to WD catalytic efficiency, there is also the need for electronic conductivity in this region for membrane-integrated artificial photosynthesis (AP) systems. Graphene oxide (GO) was shown to catalyze WD and to be controllably reduced, which resulted in electronic conductivity. Layer-by-layer (LbL) film deposition was employed to improve GO film uniformity in the interfacial region to enhance WD catalysis and, through the addition of a conducting polymer in the process, add electronic conductivity in a hybrid film. Three different deposition methods were tested to optimize conducting polymer synthesis with the oxidant in a metastable solution and to yield the best film properties. It was found that an approach that included substrate dipping in a solution containing the expected final monomer/oxidant ratio provided the most predictable film growth and smoothest films (by UV/Vis spectroscopy and atomic force microscopy/scanning electron microscopy, respectively), whereas dipping in excess oxidant or co-spraying the oxidant and monomer produced heterogeneous films. Optimized films were found to be electronically conductive and produced a membrane ohmic drop that was acceptable for AP applications. Films were integrated into the interfacial region of BPMs and revealed superior WD efficiency (≥1.4 V at 10 mA cm -2 ) for thinner films (<10 bilayers≈100 nm) than for either the pure GO catalyst or conducting polymer individually, which indicated that there was a synergistic effect between these materials in the structure configured by the LbL method. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Investigation and Control of VIVs with Multi-Lock-in Regions on Wide Flat Box Girders

    Directory of Open Access Journals (Sweden)

    Bo Wu

    2017-01-01

    Full Text Available On the preliminary designing of a wide flat box girder with the slenderness ratio 12, vertical and torsional vortex-induced vibrations (VIV are observed in wind tunnel tests. More than one lock-in region, which are defined as “multi-lock-in regions,” are recorded. Therefore, suspicions should be aroused regarding the viewpoint that wide box girders are aerodynamic friendly. As the three nascent vortexes originating at the pedestrian guardrails and inspection rails shed to near-wake through different pathways with different frequencies, the mechanisms of VIVs and multi-lock-in regions are analyzed to be determined by the inappropriate subsidiary structures. A hybrid method combining Large Eddy Simulation (LES with experimental results is introduced to study the flow-structure interactions (FSI when undergoing VIVs; the vortex mode of torsional VIV on wide flat box girders is defined as “4/2S,” which is different from any other known ones. Based on the mechanism of VIV, a new approach by increasing ventilation rate of the pedestrian guardrails is proved to be effective in suppressing vertical and torsional VIVs, and it is more feasible than other control schemes. Then, the control mechanisms are deeper investigated by analyzing the evolution of vortex mode and FSI using Hybrid-LES method.

  16. CTEPP STANDARD OPERATING PROCEDURE FOR CONDUCTING INTERNAL FIELD AUDITS AND QUALITY CONTROL (SOP-2.25)

    Science.gov (United States)

    This SOP describes the method for conducting internal field audits and quality control procedures. Internal field audits will be conducted to ensure the collection of high quality data. Internal field audits will be conducted by Field Auditors (the Field QA Officer and the Field...

  17. Quantitative methodology to extract regional magnetotelluric impedances and determine the dimension of the conductivity structure

    Energy Technology Data Exchange (ETDEWEB)

    Groom, R [PetRos EiKon Incorporated, Ontario (Canada); Kurtz, R; Jones, A; Boerner, D [Geological Survey of Canada, Ontario (Canada)

    1996-05-01

    This paper describes a systematic method for determining the appropriate dimensionality of magnetotelluric (MT) data from a site, and illustrates the application of this method to analyze both synthetic data and real data. Additionally, it describes the extraction of regional impedance responses from multiple sites. This method was examined extensively with synthetic data, and proven to be successful. It was demonstrated for two neighboring sites that the analysis methodology can be extremely useful in unraveling the bulk regional response when hidden by strong three-dimensional effects. Although there may still be some uncertainties remaining in the true levels for the regional responses for stations LIT000 and LITW02, the analysis has provided models which not only fit the data but are consistent for neighboring sites. It was suggested from these data that the stations are seeing significantly different structures. 12 refs.

  18. Chaos Control in a New Three-Dimensional Chaotic T System

    International Nuclear Information System (INIS)

    Chen Yong; Yan Zhenya

    2008-01-01

    In this paper, we study chaos control of the new 3D chaotic system. We use three feedback methods (the linear, speed, doubly-periodic function controller) to suppress the chaos to unstable equilibrium. As a result, some controllers are obtained. Moreover, numerical simulations are used to verify the effectiveness of the obtained controllers

  19. Development and Evaluation of a Control System for Regional Traffic Management

    Directory of Open Access Journals (Sweden)

    John L. McLin

    2011-01-01

    Full Text Available Traffic congestion is a worsening problem in metropolitan areas which will require integrated regional traffic control systems to improve traffic conditions. This paper presents a regional traffic control system which can detect incident conditions and provide integrated traffic management during nonrecurrent congestion events. The system combines advanced artificial intelligence techniques with a traffic performance model based on HCM equations. Preliminary evaluation of the control system using traffic microsimulation demonstrates that it has the potential to improve system conditions during traffic incidents. In addition, several enhancements were identified which will make the system more robust in a real traffic control setting. An assessment of the control system elements indicates that there are no substantial technical barriers in implementing this system in a large traffic network.

  20. Research on a Compound Control Strategy of Three-Phase Inverter for Unbalanced Loads

    Directory of Open Access Journals (Sweden)

    Yue Gaili

    2017-01-01

    Full Text Available To solve the problem of unbalanced output voltage of inverter under three-phase unbalanced load. In this paper, the main circuit topology using three-phase three-wire inverter topology. Established the mathematical model in several different coordinate system of the three-phase inverter. A compound control method is proposed by combining voltage current dual loop control method and repetitive control method, The control method is realized in three - phase 400 Hz inverter, and can meet the demand of unbalanced load to inverter, the reliability of the inverter circuit is improved. At the end of this paper, Matlab simulation analysis and experimental results are given, it is proved that the composite control method designed in this paper has a strong ability of unbalanced load.

  1. Three-dimensional P velocity structure of the crust and upper mantle under Beijing region

    Energy Technology Data Exchange (ETDEWEB)

    Quan, A.; Liu, F.; Sun, Y.

    1980-04-01

    By use of the teleseismic P arrival times at 15 stations of the Beijing network for 120 events distributed over various azimuths, we studied the three-dimensional P velocity structure under the Beijing region. In calculating the theoretic travel time, we adopted the source parameters given in BISC, and used the J-B model as the standard model of earth. On inversion, we adopted singular value decomposition as a generalized inversion package, which can be used for solving very large over-determined systems of equations Gm = t without resorting to normal equations G/sup T/Gm = G/sup T/t. The results are that within the crust and upper mantle under the Beijing region there are clear lateral differences. In the results obtained by use of data from 1972 to 1975, it can be seen that there are three different zones of P-velocity. In the southeast Beijing region, P velocity is lower than that of the normal model by 10 to 14% within the crust, and by 8 to 9% within the upper mantle. The northwest Beijing region is a higher-velocity zone, within which the average P-velocity is faster than that of the normal model by about 9%. It disappears after entering into the upper mantle. The central part of this region is a normal zone. On the surface, the distribution of these P velocity variations corresponds approximately to the distribution of the over-burden. But in the deeper region, the distribution of velocity variation agrees with the distribution of seismicity. It is interesting to note that the hypocenters of several major earthquakes in this region, e.g., the Sanhe-Pinggu earthquake (1679, M = 8), the Shacheng earthquake (1730, M = 6-3/4) and the Tangshan earthquake (1976, M = 7.8), are all located very close to this boundary of these P-velocity variation zones.

  2. Thermal and Electrical Conductivities of a Three-Dimensional Ideal Anyon Gas with Fractional Exclusion Statistics

    International Nuclear Information System (INIS)

    Qin Fang; Wen Wen; Chen Ji-Sheng

    2014-01-01

    The thermal and electrical transport properties of an ideal anyon gas within fractional exclusion statistics are studied. By solving the Boltzmann equation with the relaxation-time approximation, the analytical expressions for the thermal and electrical conductivities of a three-dimensional ideal anyon gas are given. The low-temperature expressions for the two conductivities are obtained by using the Sommerfeld expansion. It is found that the Wiedemann—Franz law should be modified by the higher-order temperature terms, which depend on the statistical parameter g for a charged anyon gas. Neglecting the higher-order terms of temperature, the Wiedemann—Franz law is respected, which gives the Lorenz number. The Lorenz number is a function of the statistical parameter g. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

  3. The Wilkes subglacial basin eastern margin electrical conductivity anomaly

    Science.gov (United States)

    Rizzello, Daniele; Armadillo, Egidio; Ferraccioli, Fausto; Caneva, Giorgio

    2014-05-01

    We have analyzed the deep conductivity structure at the transition between the Transantarctic Mountains (TAM) and the eastern margin of the WSB in NVL, by means of the GDS (Geomagnetic Deep Sounding) technique, in order to constrain the geodynamical interpretation of this antarctic sector. The TAM form the uplifted flank of the Mesozoic and Cenozoic West Antarctic Rift System. Structure of the TAM rift flank has been partially investigated with different geophysical approaches.The Wilkes Subglacial Basin is a broad depression over 400 km wide at the George V Coast and 1200 km long. Geology, lithospheric structure and tectonics of the Basin are only partially known because the Basin is buried beneath the East Antarctic Ice Sheet and is located in a remote region which makes geophysical exploration logistically challenging. Different authors have proposed contrasting hypothesis regarding the origin of the WSB: it could represent a region of rifted continental crust, or it may have a flexural origin or might represent an "extended terrane". Recently aerogeophysical investigations have demonstrated a strong structural control on the margin. Magnetovariational studies carried out at high geomagnetic latitudes are often hampered by source effects, mainly due to the closeness to the Polar Electrojet currents systems (PEJ). Its presence, in fact, makes the uniform magnetic field assumption, on which the magnetovariational methods are based on, often invalid, which outcome is a bias in the GDS transfer functions and to compromise the reliability of the inverted models. Data from the aforementioned campaigns have been then processed under the ISEE project (Ice Sheet Electromagnetic Experiment), aimed at evaluate and mitigate the bias effect of the PEJ on geomagnetic an magnetotelluric transfer functions at high geomagnetic latitudes, by means of suitable processing algorithms, developed upon a statistical analysis study on PEJ effects (Rizzello et al. 2013). Recent results

  4. Fault tolerant control of a three-phase three-wire shunt active filter system based on reliability analysis

    Energy Technology Data Exchange (ETDEWEB)

    Poure, P. [Laboratoire d' Instrumentation Electronique de Nancy LIEN, EA 3440, Nancy-Universite, Faculte des Sciences et Techniques, BP 239, 54506 Vandoeuvre Cedex (France); Weber, P.; Theilliol, D. [Centre de Recherche en Automatique de Nancy UMR 7039, Nancy-Universite, CNRS, Faculte des Sciences et Techniques, BP 239, 54506 Vandoeuvre Cedex (France); Saadate, S. [Groupe de Recherches en Electrotechnique et Electronique de Nancy UMR 7037, Nancy-Universite, CNRS, Faculte des Sciences et Techniques, BP 239, 54506 Vandoeuvre Cedex (France)

    2009-02-15

    This paper deals with fault tolerant shunt three-phase three-wire active filter topologies for which reliability is very important in industry applications. The determination of the optimal reconfiguration structure among various ones with or without redundant components is discussed based on reliability criteria. First, the reconfiguration of the inverter is detailed and a fast fault diagnosis method for power semi-conductor or driver fault detection and compensation is presented. This method avoids false fault detection due to power semi-conductors switching. The control architecture and algorithm are studied and a fault tolerant control strategy is considered. Simulation results in open and short circuit cases validate the theoretical study. Finally, the reliability of the studied three-phase three-wire filter shunt active topologies is analyzed to determine the optimal one. (author)

  5. Three-dimensional fluid flow phenomena in the blade end wall corner region

    Science.gov (United States)

    Hazarika, B. K.; Raj, R.; Boldman, D. R.

    1986-01-01

    Flow visualization, static and total pressure measurements, and mean velocity profile measurements with a single-sensor inclined hot wire probe, are used in a study of three-dimensional flow at a turbine blade end wall corner region for six critical axial stations along the blade chord. Three vortices are identified: (1) a horseshoe vortex near the leading edge; (2) a corner eddy between the horseshoe vortex and the corner; and (3) a vortex at the rear portion of the corner due to the corner eddy's secondary flow. Attention is given to the relative size and rate-of-spread of the vortices in the streamwise direction.

  6. Research on Control System of Three - phase Brushless DC Motor for Electric Vehicle

    Science.gov (United States)

    Wang, Zhiwei; Jin, Hai; Guo, Jie; Su, Jie; Wang, Miao

    2017-12-01

    In order to study the three-phase brushless motor control system of electric vehicle, Freescale9S12XS128 chip is used as the control core, and the power MOSFET is used as the inverter device. The software is compiled by Codewarrior software. The speed control link adopts open-loop control, and the control chip collects the external sensor signal voltage Change control PWM signal output control three-phase brushless DC motor speed. The whole system consists of Hall position detection module, current detection module, power drive module and voltage detection module. The basic functions of three-phase brushless DC motor drive control are realized.

  7. Ionospheric control of the magnetosphere: conductance

    Directory of Open Access Journals (Sweden)

    A. J. Ridley

    2004-01-01

    Full Text Available It is well known that the ionosphere plays a role in determining the global state of the magnetosphere. The ionosphere allows magnetospheric currents to close, thereby allowing magnetospheric convection to occur. The amount of current which can be carried through the ionosphere is mainly determined by the ionospheric conductivity. This paper starts to quantify the nonlinear relationship between the ionospheric conductivity and the global state of the magnetosphere. It is found that the steady-state magnetosphere acts neither as a current nor as a voltage generator; a uniform Hall conductance can influence the potential pattern at low latitudes, but not at high latitude; the EUV generated conductance forces the currents to close in the sunlight, while the potential is large on the nightside; the solar generated Hall conductances cause a large asymmetry between the dawn and dusk potential, which effects the pressure distribution in the magnetosphere; a uniform polar cap potential removes some of this asymmetry; the potential difference between solar minimum and maximum is ∼11%; and the auroral precipitation can be related to the local field-aligned current through an exponential function. Key words. Ionosphere (ionosphere-magnetosphere interactions; modelling and forecasting; polar ionosphere

  8. Forward Conduction Mode Controlled Piezoelectric Transformer-Based PFC LED Drive

    DEFF Research Database (Denmark)

    Roedgaard, M. S.; Weirich, M.; Andersen, M. A. E.

    2013-01-01

    Light-emitting diode (LED) illumination is getting more and more common; as LED's performance is rising, the price is falling and is getting competitive. Some of the challenges of ac mains supplied illumination are the requirement of power factor correction (PFC) and the competitiveness of a low...... priced market. In this paper, a new forward conduction mode (FCM) control method for piezoelectric transformer (PT)-based power converters is proposed. A PT-based LED drive facilitating passive PFC is developed, utilizing and validating the FCM control method. The drive utilizes an inductorless half...... LED drive has been developed, supplied from 230-V 50-Hz ac mains, achieving a power factor of 0.96....

  9. Creating a Three-Parent Child: An Educational Paradigm for the Responsible Conduct of Research

    Directory of Open Access Journals (Sweden)

    Ruth L. Fischbach

    2014-10-01

    Full Text Available The field of assisted reproduction is renowned for its remarkable advances and constant pushing forward of research boundaries in an effort to offer innovative and effective methods for enhancing fertility. Accompanying these advances, however, are physiological, psychological, and bioethical consequences that must be considered. These concomitant advances and consequences make assisted reproduction an excellent educational paradigm for inculcating responsible conduct in both research and clinical practice. Ultimately, responsible conduct rests on the ethical researcher and clinician. Here, we present the as-yet unapproved, contentious assisted reproductive technology of mitochondrial replacement transfer (MRT as an ideal educational platform to foster the responsible conduct of research by advancing dialogue among multidisciplinary scholars, researchers, and students. Using a likely future case, we present the basic science, legal, and ethical considerations, and the pedagogical principles and strategies for using MRT as an effective educational paradigm. Society will benefit when the ethical issues inherent in creating children with three genetic parents as well as germline interference are discussed across multiple academic levels that include researchers, legal experts, bioethicists, and government-appointed commissions. Furthermore, undergraduate and graduate students should be included because they will likely determine the ethical fates of these biotechnologies. While emerging assisted reproduction technologies such as MRT are highly complex and will take years to be readily available for patients in need, now is the time to consider their scientific, legal, ethical, and cultural/religious implications for ensuring the responsible conduct of research.

  10. Speed-controlled three-phase drives. Drehzahlgeregelte Drehstromantriebe

    Energy Technology Data Exchange (ETDEWEB)

    Steinmetz, E

    1981-01-01

    Present semiconductor circuit elements have made it possible to produce frequency converters for speed-controlled three-phase drives from the k'' range to the MW range at low cost. Line-powered frequency converter circuits are already in the standardisation stage while the development trends in the field of speed-controlled frequency converter circuits are not foreseeable as yet. Recent developments in the field of electronics have made the circuits simpler and able to implement an increasing number of functions. There is a trend towards programmable digital control systems with microcomputers. Of the 8 articles in the publication, the contribution by M. Wild and R. Wetzl (Synchronous motors with frequency converters drive boiler feed pumps at Bergkamen power plant) has been entered in the data base as a separate citation.

  11. Three-dimensional ionic conduction in the strained electrolytes of solid oxide fuel cells

    International Nuclear Information System (INIS)

    Han, Yupei; Zou, Minda; Lv, Weiqiang; He, Weidong; Mao, Yiwu; Wang, Wei

    2016-01-01

    Flexible power sources including fuel cells and batteries are the key to realizing flexible electronic devices with pronounced foldability. To understand the bending effects in these devices, theoretical analysis on three-dimensional (3-D) lattice bending is necessary. In this report, we derive a 3-D analytical model to analyze the effects of electrolyte crystal bending on ionic conductivity in flexible solid-state batteries/fuel cells. By employing solid oxide fuel cells as a materials' platform, the intrinsic parameters of bent electrolyte materials, including lattice constant, Young's modulus, and Poisson ratio, are evaluated. Our work facilitates the rational design of highly efficient flexible electrolytes for high-performance flexible device applications.

  12. [Tuberculosis control in the Central Health Region of Catalonia during the period 1986-2000].

    Science.gov (United States)

    Miret Cuadras, P; Pina Gutiérrez, J M; López Sanmartín, J L; Sala Farré, M R

    2003-10-01

    To assess tuberculosis control in the Central Health Region, Catalonia, Spain, from the implementation of the area's Tuberculosis Control Program in 1986 until the year 2000. To study the epidemiological profile of tuberculosis and the outcome of the following control measures in sputum smear-positive patients: final outcome of treatment and monitoring, and the percentage of patients for whom a contact investigation (CI) was carried out. Tuberculosis control is considered effective if the sum of noncompliant patients, plus the cases in which treatment failed, plus the patients transferred out remains below 10% of the cohort of patients studied, and if a CI has been conducted in at least 80% of this cohort. The number of cases reported was 6326, of which 7% were retreatments. A total of 5865 new cases was detected. Of these, 5652 (96%) were patients born in Spain. The number of cases reported annually peaked in 1990 (474) and then declined continuously until 2000, when it was 54% lower (220). Foreign-born patients numbered 213 (4%), and 95% of them came from countries with a high prevalence of tuberculosis. In the cohort of patients studied between 1997 and 2000, the sum of noncompliant patients, plus cases in which treatment failed, plus the patients transferred out came to 11%. Since 1994, a CI has been carried out for over 80% of patients, and this figure reached 92% in 2000. We consider that a substantial degree of tuberculosis control has been achieved given the decline in tuberculosis morbidity among people born in Spain, the fact that the percentage of noncompliant patients, treatment failures and transfers was only slightly over 10%, and that a CI has been conducted for over 80% of patients since 1994 (92% in 2000).

  13. Prevalence of Dyslipidemias in Three Regions in Venezuela: The VEMSOLS Study Results

    Science.gov (United States)

    González-Rivas, Juan P.; Nieto-Martínez, Ramfis; Brajkovich, Imperia; Ugel, Eunice; Rísquez, Alejandro

    2018-01-01

    Background The prevalence of dyslipidemia in multiple regions of Venezuela is unknown. The Venezuelan Metabolic Syndrome, Obesity and Lifestyle Study (VEMSOLS) was undertaken to evaluate cardiometabolic risk factors in Venezuela. Objective To determine the prevalence of dyslipidemia in five populations from three regions of Venezuela. Methods During the years 2006 to 2010, 1320 subjects aged 20 years or older were selected by multistage stratified random sampling from all households in five municipalities from 3 regions of Venezuela: Lara State (Western region), Merida State (Andean region), and Capital District (Capital region). Anthropometric measurements and biochemical analysis were obtained from each participant. Dyslipidemia was defined according to the NCEP/ATPIII definitions. Results Mean age was 44.8 ± 0.39 years and 68.5% were females. The prevalence of lipids abnormalities related to the metabolic syndrome (low HDL-c [58.6%; 95% CI 54.9 - 62.1] and elevated triglycerides [39.7%; 36.1 - 43.2]) were the most prevalent lipid alterations, followed by atherogenic dyslipidemia (25.9%; 22.7 - 29.1), elevated LDL-c (23.3%; 20.2 - 26.4), hypercholesterolemia (22.2%; 19.2 - 25.2), and mix dyslipidemia (8.9%; 6.8 - 11.0). Dyslipidemia was more prevalent with increasing body mass index. Conclusion Dyslipidemias are prevalent cardiometabolic risk factors in Venezuela. Among these, a higher prevalence of low HDL is a condition also consistently reported in Latin America. PMID:29538522

  14. Adaptive Control of a Utility-Scale Wind Turbine Operating in Region 3

    Science.gov (United States)

    Frost, Susan A.; Balas, Mark J.; Wright, Alan D.

    2009-01-01

    Adaptive control techniques are well suited to nonlinear applications, such as wind turbines, which are difficult to accurately model and which have effects from poorly known operating environments. The turbulent and unpredictable conditions in which wind turbines operate create many challenges for their operation. In this paper, we design an adaptive collective pitch controller for a high-fidelity simulation of a utility scale, variable-speed horizontal axis wind turbine. The objective of the adaptive pitch controller in Region 3 is to regulate generator speed and reject step disturbances. The control objective is accomplished by collectively pitching the turbine blades. We use an extension of the Direct Model Reference Adaptive Control (DMRAC) approach to track a reference point and to reject persistent disturbances. The turbine simulation models the Controls Advanced Research Turbine (CART) of the National Renewable Energy Laboratory in Golden, Colorado. The CART is a utility-scale wind turbine which has a well-developed and extensively verified simulator. The adaptive collective pitch controller for Region 3 was compared in simulations with a bas celliansesical Proportional Integrator (PI) collective pitch controller. In the simulations, the adaptive pitch controller showed improved speed regulation in Region 3 when compared with the baseline PI pitch controller and it demonstrated robustness to modeling errors.

  15. Electrical conductivity imaging in the western Pacific subduction zone

    Science.gov (United States)

    Utada, Hisashi; Baba, Kiyoshi; Shimizu, Hisayoshi

    2010-05-01

    Oceanic plate subduction is an important process for the dynamics and evolution of the Earth's interior, as it is regarded as a typical downward flow of the mantle convection that transports materials from the near surface to the deep mantle. Recent seismological study showed evidence suggesting the transportation of a certain amount of water by subduction of old oceanic plate such as the Pacific plate down to 150-200 km depth into the back arc mantle. However it is not well clarified how deep into the mantle the water can be transported. The electromagnetic induction method to image electrical conductivity distribution is a possible tool to answer this question as it is known to be sensitive to the presence of water. Here we show recent result of observational study from the western Pacific subduction zone to examine the electrical conductivity distribution in the upper mantle and in the mantle transition zone (MTZ), which will provide implications how water distributes in the mantle. We take two kinds of approach for imaging the mantle conductivity, (a) semi-global and (b) regional induction approaches. Result may be summarized as follows: (a) Long (5-30 years) time series records from 8 submarine cables and 13 geomagnetic observatories in the north Pacific region were analyzed and long period magnetotelluric (MT) and geomagnetic deep sounding (GDS) responses were estimated in the period range from 1.7 to 35 days. These frequency dependent response functions were inverted to 3-dimensional conductivity distribution in the depth range between 350 and 850 km. Three major features are suggested in the MTZ depth such as, (1) a high conductivity anomaly beneath the Philippine Sea, (2) a high conductivity anomaly beneath the Hawaiian Islands, and (3) a low conductivity anomaly beneath and in the vicinity of northern Japan. (b) A three-year long deployment of ocean bottom electro-magnetometers (OBEM's) was conducted in the Philippine Sea and west Pacific Ocean from 2005

  16. Thermalhydraulic behavior of electrically heated rods during critical heat flux transients

    International Nuclear Information System (INIS)

    Lima, Rita de Cassia Fernandes de

    1997-01-01

    In nuclear reactors, the occurrence of critical heat flux leads to fuel rod overheating with clad fusion and radioactive products leakage. To predict the effects of such phenomenon, experiments are performed utilizing heated rods to simulate operational and accidental conditions of nuclear fuel rods, with special attention to the phenomenon of boiling crisis. The use of mechanisms which detect the abrupt temperature rise allows the electric power switch off. These facts prevent the test section from damage. During the critical heat flux phenomenon the axial heat conduction becomes very important. The study of the dryout and rewetting fronts yields the analysis, planning and following of critical heat flux experiments. These facts are important during the reflooding of nuclear cores at severe accidents. In the present work it is performed a theoretical analysis of the drying and rewetting front propagation during a critical heat flux experiment, starting with the application of an electrical power step or power slope from steady state condition. After the occurrence of critical heat flux, it is predicted the drying front propagation. After a few seconds, a power cut is considered and the rewetting front behavior is analytically observed. In all these transients the coolant pressure is 13,5 MPa. For one of them, comparisons are done with a pressure of 8,00 MPa. Mass flow and enthalpy influences on the fronts velocities are also analysed. These results show that mass flow has more importance on the drying front velocities whereas the pressure alters strongly the rewetting ones. (author)

  17. Adaptive nonlinear control of single-phase to three-phase UPS system

    Directory of Open Access Journals (Sweden)

    Kissaoui M.

    2014-01-01

    Full Text Available This work deals with the problems of uninterruptible power supplies (UPS based on the single-phase to three-phase converters built in two stages: an input bridge rectifier and an output three phase inverter. The two blocks are joined by a continuous intermediate bus. The objective of control is threefold: i power factor correction “PFC”, ii generating a symmetrical three-phase system at the output even if the load is unknown, iii regulating the DC bus voltage. The synthesis of controllers has been reached by two nonlinear techniques that are the sliding mode and adaptive backstepping control. The performances of regulators have been validated by numerical simulation in MATLAB / SIMULINK.

  18. Macro-mechanics controls quantum mechanics: mechanically controllable quantum conductance switching of an electrochemically fabricated atomic-scale point contact.

    Science.gov (United States)

    Staiger, Torben; Wertz, Florian; Xie, Fangqing; Heinze, Marcel; Schmieder, Philipp; Lutzweiler, Christian; Schimmel, Thomas

    2018-01-12

    Here, we present a silver atomic-scale device fabricated and operated by a combined technique of electrochemical control (EC) and mechanically controllable break junction (MCBJ). With this EC-MCBJ technique, we can perform mechanically controllable bistable quantum conductance switching of a silver quantum point contact (QPC) in an electrochemical environment at room temperature. Furthermore, the silver QPC of the device can be controlled both mechanically and electrochemically, and the operating mode can be changed from 'electrochemical' to 'mechanical', which expands the operating mode for controlling QPCs. These experimental results offer the perspective that a silver QPC may be used as a contact for a nanoelectromechanical relay.

  19. Macro-mechanics controls quantum mechanics: mechanically controllable quantum conductance switching of an electrochemically fabricated atomic-scale point contact

    Science.gov (United States)

    Staiger, Torben; Wertz, Florian; Xie, Fangqing; Heinze, Marcel; Schmieder, Philipp; Lutzweiler, Christian; Schimmel, Thomas

    2018-01-01

    Here, we present a silver atomic-scale device fabricated and operated by a combined technique of electrochemical control (EC) and mechanically controllable break junction (MCBJ). With this EC-MCBJ technique, we can perform mechanically controllable bistable quantum conductance switching of a silver quantum point contact (QPC) in an electrochemical environment at room temperature. Furthermore, the silver QPC of the device can be controlled both mechanically and electrochemically, and the operating mode can be changed from ‘electrochemical’ to ‘mechanical’, which expands the operating mode for controlling QPCs. These experimental results offer the perspective that a silver QPC may be used as a contact for a nanoelectromechanical relay.

  20. Phytotherapy of High Blood Pressure in Three Phytogeographic Regions of Cameroon.

    Science.gov (United States)

    Tsabang, Nole; Yedjou, Clement G; Tchounwou, Paul B

    2017-01-01

    High blood pressure is a public health challenge worldwide. According to World Health Organization, 30% of men and 50% of women 65 to 75 years old are suffering from high blood pressure. The number of hypertensive patients in the world will attain 1.56 billion of people, with 60% increase in prevalence. The incidence of high blood pressure increases with age, but nowadays, is being noticed an increasing incidence in young people. The socio-cultural medicine may provide new solutions in the management of this pathology. Therefore this study was carried out to record and document plants used against high blood pressure in socio-cultural medicine for future drugs discovery worldwide. An ethno botanical survey was realized between 2002 and 2016 to identify manifold plants used to fight against high blood pressure. This survey was carried out in three phytogeographic regions of Cameroon. Amongst people living in those regions, 1131 randomly screened interviewees distributed in 58 socio-cultural groups were involved in this study. This survey reveals that about 70% of interviewees don't know high blood pressure which is a symptomless disease. A total of 28 species of plants were recorded. These plants belong to 25 genera and 24 families. They were used to prepare 28 herbal remedies for the treatment of high blood pressure. In the morphological point of view about 10/28 (36%) plants are herbs; 9/28 (32%) plants are trees and 9/28 (32%) plants are shrubs. Only 3/28 plants (11%) used including Allium sativum, Aloe barteri and Aloe buttneri) are cultivated. This means that the plants used in this study don't usually have some form of protection through cultivation which is encouraging in terms of their conservation. The uncontrolled use of a hypotensive plants can provoke a fatal hypotension in hypertensive patients. Therefore the use of hypotensive plants needs to be controlled by physician or by a patient verification using a blood pressure monitor. Recorded species which

  1. Reducing child conduct problems and promoting social skills in a middle-income country: cluster randomised controlled trial.

    Science.gov (United States)

    Baker-Henningham, Helen; Scott, Stephen; Jones, Kelvyn; Walker, Susan

    2012-08-01

    There is an urgent need for effective, affordable interventions to prevent child mental health problems in low- and middle-income countries. To determine the effects of a universal pre-school-based intervention on child conduct problems and social skills at school and at home. In a cluster randomised design, 24 community pre-schools in inner-city areas of Kingston, Jamaica, were randomly assigned to receive the Incredible Years Teacher Training intervention (n = 12) or to a control group (n = 12). Three children from each class with the highest levels of teacher-reported conduct problems were selected for evaluation, giving 225 children aged 3-6 years. The primary outcome was observed child behaviour at school. Secondary outcomes were child behaviour by parent and teacher report, child attendance and parents' attitude to school. The study is registered as ISRCTN35476268. Children in intervention schools showed significantly reduced conduct problems (effect size (ES) = 0.42) and increased friendship skills (ES = 0.74) through observation, significant reductions to teacher-reported (ES = 0.47) and parent-reported (ES = 0.22) behaviour difficulties and increases in teacher-reported social skills (ES = 0.59) and child attendance (ES = 0.30). Benefits to parents' attitude to school were not significant. A low-cost, school-based intervention in a middle-income country substantially reduces child conduct problems and increases child social skills at home and at school.

  2. Controlled Quantum Operations of a Semiconductor Three-Qubit System

    Science.gov (United States)

    Li, Hai-Ou; Cao, Gang; Yu, Guo-Dong; Xiao, Ming; Guo, Guang-Can; Jiang, Hong-Wen; Guo, Guo-Ping

    2018-02-01

    In a specially designed semiconductor device consisting of three capacitively coupled double quantum dots, we achieve strong and tunable coupling between a target qubit and two control qubits. We demonstrate how to completely switch on and off the target qubit's coherent rotations by presetting two control qubits' states. A Toffoli gate is, therefore, possible based on these control effects. This research paves a way for realizing full quantum-logic operations in semiconductor multiqubit systems.

  3. A comparison of three self-tuning control algorithms developed for the Bristol-Babcock controller

    International Nuclear Information System (INIS)

    Tapp, P.A.

    1992-04-01

    A brief overview of adaptive control methods relating to the design of self-tuning proportional-integral-derivative (PID) controllers is given. The methods discussed include gain scheduling, self-tuning, auto-tuning, and model-reference adaptive control systems. Several process identification and parameter adjustment methods are discussed. Characteristics of the two most common types of self-tuning controllers implemented by industry (i.e., pattern recognition and process identification) are summarized. The substance of the work is a comparison of three self-tuning proportional-plus-integral (STPI) control algorithms developed to work in conjunction with the Bristol-Babcock PID control module. The STPI control algorithms are based on closed-loop cycling theory, pattern recognition theory, and model-based theory. A brief theory of operation of these three STPI control algorithms is given. Details of the process simulations developed to test the STPI algorithms are given, including an integrating process, a first-order system, a second-order system, a system with initial inverse response, and a system with variable time constant and delay. The STPI algorithms' performance with regard to both setpoint changes and load disturbances is evaluated, and their robustness is compared. The dynamic effects of process deadtime and noise are also considered. Finally, the limitations of each of the STPI algorithms is discussed, some conclusions are drawn from the performance comparisons, and a few recommendations are made. 6 refs

  4. Ionospheric control of the magnetosphere: conductance

    Directory of Open Access Journals (Sweden)

    A. J. Ridley

    2004-01-01

    Full Text Available It is well known that the ionosphere plays a role in determining the global state of the magnetosphere. The ionosphere allows magnetospheric currents to close, thereby allowing magnetospheric convection to occur. The amount of current which can be carried through the ionosphere is mainly determined by the ionospheric conductivity. This paper starts to quantify the nonlinear relationship between the ionospheric conductivity and the global state of the magnetosphere. It is found that the steady-state magnetosphere acts neither as a current nor as a voltage generator; a uniform Hall conductance can influence the potential pattern at low latitudes, but not at high latitude; the EUV generated conductance forces the currents to close in the sunlight, while the potential is large on the nightside; the solar generated Hall conductances cause a large asymmetry between the dawn and dusk potential, which effects the pressure distribution in the magnetosphere; a uniform polar cap potential removes some of this asymmetry; the potential difference between solar minimum and maximum is ∼11%; and the auroral precipitation can be related to the local field-aligned current through an exponential function.

    Key words. Ionosphere (ionosphere-magnetosphere interactions; modelling and forecasting; polar ionosphere

  5. Fabrication of Superhydrophobic Surfaces with Controllable Electrical Conductivity and Water Adhesion.

    Science.gov (United States)

    Ye, Lijun; Guan, Jipeng; Li, Zhixiang; Zhao, Jingxin; Ye, Cuicui; You, Jichun; Li, Yongjin

    2017-02-14

    A facile and versatile strategy for fabricating superhydrophobic surfaces with controllable electrical conductivity and water adhesion is reported. "Vine-on-fence"-structured and cerebral cortex-like superhydrophobic surfaces are constructed by filtering a suspension of multiwalled carbon nanotubes (MWCNTs), using polyoxymethylene nonwovens as the filter paper. The nonwovens with micro- and nanoporous two-tier structures act as the skeleton, introducing a microscale structure. The MWCNTs act as nanoscale structures, creating hierarchical surface roughness. The surface topography and the electrical conductivity of the superhydrophobic surfaces are controlled by varying the MWCNT loading. The vine-on-fence-structured surfaces exhibit "sticky" superhydrophobicity with high water adhesion. The cerebral cortex-like surfaces exhibit self-cleaning properties with low water adhesion. The as-prepared superhydrophobic surfaces are chemically resistant to acidic and alkaline environments of pH 2-12. They therefore have potential in applications such as droplet-based microreactors and thin-film microextraction. These findings aid our understanding of the role that surface topography plays in the design and fabrication of superhydrophobic surfaces with different water-adhesion properties.

  6. Development of a thermal-hydraulic code for reflood analysis in a PWR experimental loop

    International Nuclear Information System (INIS)

    Alves, Sabrina P.; Mesquita, Amir Z.; Rezende, Hugo C.; Palma, Daniel A.P.

    2017-01-01

    A process of fundamental importance in the event of Loss of Coolant Accident (LOCA) in Pressurized Water nuclear Reactors (PWR) is the reflood of the core or rewetting of nuclear fuels. The Nuclear Technology Development Center (CDTN) has been developing since the 70’s programs to allow Brazil to become independent in the field of reactor safety analysis. To that end, in the 80’s was designed, assembled and commissioned one Rewetting Test Facility (ITR in Portuguese). This facility aims to investigate the phenomena involved in the thermal hydraulic reflood phase of a Loss of Coolant Accident in a PWR nuclear reactor. This work aim is the analysis of physical and mathematical models governing the rewetting phenomenon, and the development a thermo-hydraulic simulation code of a representative experimental circuit of the PWR reactors core cooling channels. It was possible to elaborate and develop a code called REWET. The results obtained with REWET were compared with the experimental results of the ITR, and with the results of the Hydroflut code, that was the old program previously used. An analysis was made of the evolution of the wall temperature of the test section as well as the evolution of the front for two typical tests using the two codes calculation, and experimental results. The result simulated by REWET code for the rewetting time also came closer to the experimental results more than those calculated by Hydroflut code. (author)

  7. Development of a thermal-hydraulic code for reflood analysis in a PWR experimental loop

    Energy Technology Data Exchange (ETDEWEB)

    Alves, Sabrina P.; Mesquita, Amir Z.; Rezende, Hugo C., E-mail: sabrinapral@gmail.com, E-mail: amir@cdtn.brm, E-mail: hcr@cdtn.br, E-mail: hcr@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil); Palma, Daniel A.P., E-mail: dapalma@cnen.gov.br [Comissão Nacional de Energia Nuclear (CNEN), Rio de Janeiro, RJ (Brazil)

    2017-07-01

    A process of fundamental importance in the event of Loss of Coolant Accident (LOCA) in Pressurized Water nuclear Reactors (PWR) is the reflood of the core or rewetting of nuclear fuels. The Nuclear Technology Development Center (CDTN) has been developing since the 70’s programs to allow Brazil to become independent in the field of reactor safety analysis. To that end, in the 80’s was designed, assembled and commissioned one Rewetting Test Facility (ITR in Portuguese). This facility aims to investigate the phenomena involved in the thermal hydraulic reflood phase of a Loss of Coolant Accident in a PWR nuclear reactor. This work aim is the analysis of physical and mathematical models governing the rewetting phenomenon, and the development a thermo-hydraulic simulation code of a representative experimental circuit of the PWR reactors core cooling channels. It was possible to elaborate and develop a code called REWET. The results obtained with REWET were compared with the experimental results of the ITR, and with the results of the Hydroflut code, that was the old program previously used. An analysis was made of the evolution of the wall temperature of the test section as well as the evolution of the front for two typical tests using the two codes calculation, and experimental results. The result simulated by REWET code for the rewetting time also came closer to the experimental results more than those calculated by Hydroflut code. (author)

  8. Three-Axis Attitude Control of Solar Sails Utilising Reflectivity Control Devices

    Science.gov (United States)

    Theodorou, Theodoros

    Solar sails are spacecraft that utilise the Solar Radiation Pressure, the force generated by impinging photons, to propel themselves. Conventional actuators are not suitable for controlling the attitude of solar sails therefore specific attitude control methods have been devised to tackle this. One of these methods is to change the centre of pressure with respect to the center of mass thus creating a torque. Reflectivity Control Devices (RCDs) have been proposed and successfully used to change the centre of pressure. Current methods that utilise RCDs have control authority over two axis only with no ability to control the torque about the normal of the sail surface. This thesis extends the state of the art and demonstrates 3-axis control by generating arbitrary torque vectors within a convex polyhedron. Two different RCD materials are considered, transmission and diffusion technologies both compatible with the proposed concept. A number of metrics have been developed which facilitate the comparison of different sail configurations. One of these metics is the sun map which is a graphic representation of the sun angles for which control authority is maintained. An iterative design process is presented which makes use of the metrics developed and aids in the design of a sail which meets the mission requirements and constraints. Moreover, the effects of different parameters on the performance of the proposed control concept are discussed. For example it is shown that by alternating the angle between the edge and middle RCDs the control authority increases. The concept's scalability has been investigated and a hybrid control scheme has been devised which makes use of both RCDs and reaction wheels. The RCDs are complemented by the reaction wheels to achieve higher slew rates while in turn the RCDs desaturate the reaction wheels. Finally, a number of simulations are conducted to verify the validity of the proposed concept.

  9. Deemed Savings Estimates for Legacy Air Conditioning and WaterHeating Direct Load Control Programs in PJM Region

    Energy Technology Data Exchange (ETDEWEB)

    Goldman, Charles

    2007-03-01

    During 2005 and 2006, the PJM Interconnection (PJM) Load Analysis Subcommittee (LAS) examined ways to reduce the costs and improve the effectiveness of its existing measurement and verification (M&V) protocols for Direct Load Control (DLC) programs. The current M&V protocol requires that a PURPA-compliant Load Research study be conducted every five years for each Load-Serving Entity (LSE). The current M&V protocol is expensive to implement and administer particularly for mature load control programs, some of which are marginally cost-effective. There was growing evidence that some LSEs were mothballing or dropping their DLC programs in lieu of incurring the expense associated with the M&V. This project had several objectives: (1) examine the potential for developing deemed savings estimates acceptable to PJM for legacy air conditioning and water heating DLC programs, and (2) explore the development of a collaborative, regional, consensus-based approach for conducting monitoring and verification of load reductions for emerging load management technologies for customers that do not have interval metering capability.

  10. Tunneling Conductivity and Piezoresistivity of Composites Containing Randomly Dispersed Conductive Nano-Platelets

    Science.gov (United States)

    Oskouyi, Amirhossein Biabangard; Sundararaj, Uttandaraman; Mertiny, Pierre

    2014-01-01

    In this study, a three-dimensional continuum percolation model was developed based on a Monte Carlo simulation approach to investigate the percolation behavior of an electrically insulating matrix reinforced with conductive nano-platelet fillers. The conductivity behavior of composites rendered conductive by randomly dispersed conductive platelets was modeled by developing a three-dimensional finite element resistor network. Parameters related to the percolation threshold and a power-low describing the conductivity behavior were determined. The piezoresistivity behavior of conductive composites was studied employing a reoriented resistor network emulating a conductive composite subjected to mechanical strain. The effects of the governing parameters, i.e., electron tunneling distance, conductive particle aspect ratio and size effects on conductivity behavior were examined. PMID:28788580

  11. DIRECT ELECTION OF THE HEAD OF REGIONAL URGENCY (DESCRIPTION OF THE IMPLEMENTATION OF THE THREE AUTONOMOUS REGIONS ACT

    Directory of Open Access Journals (Sweden)

    Abdul Rahman

    2013-07-01

    Full Text Available A variety of problem and the political turmoil in some regions election last time appears in the event of a State feedback control Centre to the area. In the new order era regional chief election controversy cannot be released from the intervention Center. Usually the battle's political elite in Jakarta imposes to the area. When the issue blew up in the area, Settlement is the effort, he brought the case to Jakarta. In accordance with the implementation, the Hall of the Central Government has a dominant power in the determination of the head region. Legislative involvement only in the process of being formalistic. It is seen clearly in Article 15 and 16 regarding the appointment of the head region, where only the legislative vote and the results presented at least two names for approval and/or designation from President to Governor, and Minister of the Interior for Regent and Mayor. The aegis of the Centre to all and sundry, who has strong access to the Centre, he will be the winner, either for political affairs, economy, law even though. The most votes is not a legislative guarantee of choice became the head of the area. The Center has the absolute power to determine the opposite although sound support. Conflicts often occur, regional Centre but ended with the defeat of the area

  12. Major Differences in Diet across Three Linguistic Regions of Switzerland: Results from the First National Nutrition Survey menuCH

    Directory of Open Access Journals (Sweden)

    Angeline Chatelan

    2017-10-01

    Full Text Available Switzerland is a multilingual country located between Germany, France and Italy, which differ by dietary habits and related outcomes. We explored differences in food consumption as well as compliance to the Swiss food-based dietary guidelines (FBDG across the German-, French-, and Italian-speaking regions. The 2014–2015 nationwide cross-sectional survey was conducted among a stratified random sample of 2057 adults aged 18 to 75 years. Trained dietitians assessed food consumption via two non-consecutive 24-h dietary recalls using the international validated software GloboDiet®. Recorded foods and beverages were classified into six groups and 31 subgroups relevant for assessing compliance to the FBDG (Swiss Food Pyramid. Usual daily intake distributions were modelled and weighted for sampling design, non-response, weekdays and season. Participation rate was 38%. Significant differences across regions were observed in 18 of 31 food subgroups (p ≤ 0.01. Weighted mean daily intakes in the German-, French- and Italian-speaking regions were, respectively, 245 g, 155 g, 140 g for soft drinks, 273 g, 214 g, 135 g for coffee, 127 g, 72 g, 109 g for milk, 32 g, 45 g, 43 g for red meat, 18 g, 29 g, 34 g for fish/seafood, 8.1 g, 6.4 g, 3.7 g for butter, and 206 g, 214 g, 168 g for vegetables. The seven FBDGs were followed by <1% of the population. Four in 10 participants met ≥3 FBDG. Eighteen percent of participants ate ≥5 portions of fruit and vegetables a day, without regional differences. Food consumption substantially differed across the three linguistic regions of Switzerland. Adherence to FBDG was uniformly low. This highlights the potential influence of culture on diet. Nutritional education along with public health interventions are needed and may be most efficient if regionally targeted.

  13. Control of water infiltration into near surface LLW disposal units: Progress report on field experiments at a humid region site, Beltsville, Maryland

    International Nuclear Information System (INIS)

    Schulz, R.K.; Ridky, R.W.

    1996-08-01

    This study's objective is to assess means for controlling water infiltration through waste disposal unit covers in humid regions. Experimental work is being performed in large-scale lysimeters 21.34 m x 13.72 m x 3.05 m (70 ft x 45 ft x 10 ft) at Beltsville, Maryland. Results of the assessment are applicable to disposal of low-level radioactive waste (LLW), uranium mill tailings, hazardous waste, and sanitary landfills. Three kinds of waste disposal unit covers or barriers to water infiltration are being investigated: (1) resistive layer barrier, (2) conductive layer barrier, and (3) bioengineering management. The resistive layer barrier consists of compacted earthen material (e.g., clay). The conductive layer barrier consists of a conductive layer in conjunction with a capillary break. As long as unsaturated flow conditions are maintained, the conductive layer will wick water around the capillary break. Below-grade layered covers such as (1) and (2) will fail if there is appreciable subsidence of the cover, and remedial action for this kind of failure will be difficult. A surface cover, called bioengineering management, is meant to overcome this problem. The bioengineering management surface barrier is easily repairable if damaged by subsidence; therefore, it could be the system of choice under active subsidence conditions. The bioengineering management procedure also has been shown to be effective in dewatering saturated trenches and could be used for remedial action efforts. After cessation of subsidence, that procedure could be replaced by a resistive layer barrier or, perhaps even better, by a resistive layer barrier/conductive layer barrier system. The latter system would then give long-term effective protection against water entry into waste without institutional care

  14. Impact of emission control on regional air quality in the Pearl Delta River region, southern China

    Science.gov (United States)

    Wang, N.; Xuejiao, D.

    2017-12-01

    The Pearl River Delta (PRD) in China has been suffering from air quality issues and the government has implemented a series of strategies in controlling emissions. In an attempt to provide scientific support for improving air quality, the paper investigates the concerning past-to-present air quality data and assesses air quality resulting from emission control. Statistical data revealed that energy consumption doubled from 2004 to 20014 and vehicle usage increased significantly from 2006 to 2014. Due to the effect of control efforts, primary emission of SO2, NOx and PM2.5 decreased resulting in ambient concentrations of SO2, NO2 and PM10 decreased by 66%, 20% and 24%, respectively. However, O3 increased 19% because of the increase of VOC emission. A chemical transport model, the Community Multi-scale Air Quality, was employed to evaluate the responses of nitrate, ammonium, SOA, PM2.5 and O3 to changes in NOx, VOC and NH3 emissions. Three scenarios, a baseline scenario, a CAP scenario (control strength followed as past tendency), and a REF scenario (strict control referred to latest policy and plans), were conducted to investigate the responses and mechanisms. NOx controlling scenarios showed that NOx, nitrate and PM2.5 reduced by 1.8%, 0.7% and 0.2% under CAP and reduced by 7.2%, 1.8% and 0.3% under REF, respectively. The results indicated that reducing NOx emission caused the increase of atmospheric oxidizability, which might result in a compensation of PM2.5 due to the increase of nitrate or sulfate. NH3 controlling scenarios showed that nitrate was sensitive to NH3 emission in PRD, with nitrate decreased by 0 - 10.6% and 0 - 48% under CAP and REF, respectively. Since controlling NH3 emissions not only reduced ammonium but also significantly reduced nitrate, the implement of NH3 controlling strategy was highly suggested. The VOC scenarios revealed that though SOA was not the major component of PM2.5, controlling VOC emission might take effect in southwestern PRD

  15. Trials on the Timing of Chemical Control of Lentil weevil, Bruchus lentis Frӧlich (Coleoptera: Chrysomelidae: Bruchinae in Lentil Field in Gachsaran Region (Iran

    Directory of Open Access Journals (Sweden)

    K. Saeidi

    2017-12-01

    Full Text Available The lentil weevil, Bruchus lentis Frӧlich, (Coleoptera: Chrysomelidae: Bruchinae is the most serious pest of lentil in Iran. Economic losses due to this pest reach up to 40% of the lentil crop. Over a two-year study (2012 and 2013 in Agricultural Research Station of Gachsaran Region, best timing of chemical control of B. lentis was determined. A field experiment with cultivation of lentil Sina variety Lens culinaris Medik was conducted in a randomized complete block design with five treatments and three replications. The treatments consisted of spraying four times (respectively, during the early flowering, 10 days after the first spraying, 10 days after the second spraying; 10 days after the third spraying and control (without spraying. For the spraying from Endosulfan insecticide EC50% at ratio one liter per hectare was used. Three samples were taken from the pods and totally 150 pods from each replicate for contaminations of seeds were investigated. After the determination of the percent of seeds contamination, results were statistically analysed. Based on the results obtained, first spray treatment, with the mean contamination of 15.45% and second spray treatment with the mean contamination of 12.25% had the highest impact on reducing contamination lentil seeds to B. lentis and between them there was no statistically significant difference and were in one group. Therefore, spraying one time during the early flowering until 15 days after it was the best time to control of B. lentis.

  16. Regionally differentiated air pollution control regulations in the installation-related emission control law of the Federal Republic of Germany

    International Nuclear Information System (INIS)

    Buettner, T.W.

    1992-01-01

    The volume treats an issue from the boundary zone between environmental law and environmental economics, namely the regionalization of air pollution control standards in installation-related emission control law. In order to examine the question of whether this proposal, which originates in the field of environmental economics, can be adopted and is purposeful, the author initially performs a complete inventorization of applicable norms, this covering emission control law, the law of regional planning, and the provisions of international law. This status quo is then reviewed using conformity and optimization criteria developed by the political sciences. The assessment comes to the conclusion that the introduction of regionally differentiated air pollution control standards is not desirable. The author further submits proposals for the streamlining of the law of installation-related air pollution control in the Federal Republic of Germany. (orig.) [de

  17. Neuroanatomical correlates of attention-deficit-hyperactivity disorder accounting for comorbid oppositional defiant disorder and conduct disorder.

    Science.gov (United States)

    Sasayama, Daimei; Hayashida, Ayako; Yamasue, Hidenori; Harada, Yuzuru; Kaneko, Tomoki; Kasai, Kiyoto; Washizuka, Shinsuke; Amano, Naoji

    2010-08-01

    An increasing number of neuroimaging studies have been conducted to uncover the pathophysiology of attention-deficit-hyperactivity disorder (ADHD). The findings are inconsistent, however, at least partially due to methodological differences. In the present study voxel-based morphometry (VBM) was used to evaluate brain morphology in ADHD subjects after taking into account the confounding effect of oppositional defiant disorder (ODD) and conduct disorder (CD) comorbidity. Eighteen children with ADHD and 17 age- and gender-matched typically developing subjects underwent high-spatial resolution magnetic resonance imaging. The regional gray matter volume differences between the children with ADHD and controls were examined with and without accounting for comorbid ODD and CD in a voxel-by-voxel manner throughout the entire brain. The VBM indicated significantly smaller regional gray matter volume in regions including the bilateral temporal polar and occipital cortices and the left amygdala in subjects with ADHD compared with controls. Significantly smaller regional gray matter volumes were demonstrated in more extensive regions including the bilateral temporal polar cortices, bilateral amygdala, right occipital cortex, right superior temporal sulcus, and left middle frontal gyrus after controlling for the confounding effect of comorbid ODD and CD. Morphological abnormalities in ADHD were seen not only in the regions associated with executive functioning but also in the regions associated with social cognition. When the effect of comorbid CD and ODD was taken into account, there were more extensive regions with significantly smaller volume in ADHD compared to controls.

  18. Predictive Duty Cycle Control of Three-Phase Active-Front-End Rectifiers

    DEFF Research Database (Denmark)

    Song, Zhanfeng; Tian, Yanjun; Chen, Wei

    2016-01-01

    This paper proposed an on-line optimizing duty cycle control approach for three-phase active-front-end rectifiers, aiming to obtain the optimal control actions under different operating conditions. Similar to finite control set model predictive control strategy, a cost function previously...

  19. Relationships between seismic wave-Speed, density, and electrical conductivity beneath Australia from seismology, mineralogy, and laboratory-based conductivity profiles

    DEFF Research Database (Denmark)

    Khan, A.; Koch, S.; Shankland, T. J.

    2015-01-01

    We present maps of the three-dimensional density (ρ), electrical conductivity (σ), and shear-wave speed (VS) structure of the mantle beneath Australia and surrounding ocean in the depth range of 100–800 km. These maps derived from stochastic inversion of seismic surface-wave dispersion data...... shear-wave speeds, low densities, and high conductivities. This trend appears to continue to depths well below 300 km. The slow-fast shear-wave speed distribution found here is also observed in independent seismic tomographic models of the Australian region, whereas the coupled slow-fast shear......-wave speed, low-high density, and high-low electrical conductivity distribution has not been observed previously. Toward the bottom of the upper mantle at 400 km depth marking the olivine ⃗ wadsleyite transformation (the “410–km” seismic discontinuity), the correlation between VS, ρ, and σ weakens...

  20. Eddy covariance measurements of greenhouse gases from a restored and rewetted raised bog ecosystem.

    Science.gov (United States)

    Lee, S. C.; Christen, A.; Black, T. A.; Johnson, M. S.; Ketler, R.; Nesic, Z.; Merkens, M.

    2015-12-01

    Wetland ecosystems play a significant role in the global carbon (C) cycle. Wetlands act as a major long-term storage of carbon by sequestrating carbon-dioxide (CO2) from the atmosphere. Meanwhile, they can emit significant amounts of methane (CH4) due to anaerobic microbial decomposition. The Burns Bog Ecological Conservancy Area (BBECA) is recognized as one of Canada's largest undeveloped natural areas retained within an urban area. Historically, it has been substantially reduced in size and degraded by peat mining and agriculture. Since 2005, the bog has been declared a conservancy area, and the restoration efforts in BBECA focus on rewetting the disturbed ecosystems to promote a transition back to a raised bog. A pilot study measured CH4, CO2 and N2O exchanges in 2014 and concluded to monitor CO2, CH4 fluxes continuously. From the perspective of greenhouse gas (GHG) emissions, CO2 sequestered in bog needs to be protected and additional CO2 and CH4 emissions due to land-cover change need to be reduced by wise management. In this study, we measured the growing-season (June-September) fluxes of CO2 and CH4 exchange using eddy covariance (EC). A floating platform with an EC system for both CO2 (closed-path) and CH4 (open-path) began operation in June 2015. During the growing-season, gross ecosystem photosynthesis (GEP) and ecosystem respiration (Re) averaged 5.87 g C m-2 day-1 and 2.02 g C m-2 day-1, respectively. The magnitude of GEP and Re were lower than in previous studies of pristine northern peatlands. The daily average CH4 emission was 0.99 (±1.14) g C m-2 day-1 and it was higher than in most previous studies. We also characterized how environmental factors affected the seasonal dynamics of these exchanges in this disturbed peatland. Our measurements showed that soil temperature and soil water content were major drivers of seasonal changes of GHG fluxes. The daily average GHG warming potential (GWP) of the emissions in the growing seasons (from CO2 and CH4

  1. Fault-Tolerant Region-Based Control of an Underwater Vehicle with Kinematically Redundant Thrusters

    Directory of Open Access Journals (Sweden)

    Zool H. Ismail

    2014-01-01

    Full Text Available This paper presents a new control approach for an underwater vehicle with a kinematically redundant thruster system. This control scheme is derived based on a fault-tolerant decomposition for thruster force allocation and a region control scheme for the tracking objective. Given a redundant thruster system, that is, six or more pairs of thrusters are used, the proposed redundancy resolution and region control scheme determine the number of thruster faults, as well as providing the reference thruster forces in order to keep the underwater vehicle within the desired region. The stability of the presented control law is proven in the sense of a Lyapunov function. Numerical simulations are performed with an omnidirectional underwater vehicle and the results of the proposed scheme illustrate the effectiveness in terms of optimizing the thruster forces.

  2. Results of the IAEA/RCA personal dosemeter intercomparison in the Asian and Pacific region

    International Nuclear Information System (INIS)

    Murakami, H.; Minami, K.; Griffith, R.V.

    1994-01-01

    In 1988, the International Atomic Energy Agency started the Regional Co-operative Agreement project for strengthening the radiation protection infrastructure in the Asian and Pacific region. One component of the initial programme was a regional personal dosimetry intercomparison, which was subsequently conducted in three phases over three years during the period 1990 to 1992. Seventeen organisations of all 14 member states participated in the programmes. Irradiations and data compilation were conducted by the Japan Atomic Energy Research Institute. This paper describes the results of the intercomparison programmes and discusses some features and personal dosimetry problems in the RCA member states. (author)

  3. TRITON, 3-D Multi-Region Neutron Diffusion Burnup with Criticality Search

    International Nuclear Information System (INIS)

    1974-01-01

    1 - Nature of physical problem solved: TRITON is a multigroup diffusion depletion program in three dimensions (x,y,z). In addition to the straight K eff calculation, three types of criticality searches are possible - diluted control isotope search, region-wise smeared control isotope search, region-wise smeared control isotope search, region-wise smeared control isotope boundary search (the control isotope can be smeared over one region or over a group of regions called a control bank). The depletion equations are solved region-wise. More than one microscopic cross section library can be used in the various regions of the reactor. The same is true for self-shielding factors. Such sets of data can be changed at pre-determined time steps. 2 - Method of solution: The mathematical model employed for the solution of the finite difference equations, which is derived from a seven-point approximation of diffusion equations, is an on-line Chebyshev semi- iterative method. 3 - Restrictions on the complexity of the problem: Maximum number of: library sets: 1; self-shielding sets: 10; compositions: 100; self-shielding coefficients: 6000; groups: 10; fuel isotopes: 30; fission products: 29; isotopes: 50; burnable isotopes: 40; control banks: 100; mesh points: 15000; regions: 400; time steps: 100; control areas: 100; small time steps: 200; elements in the control list: 400; x planes: 100; y planes: 100; z planes: 100

  4. 40 CFR 81.55 - Northeast Pennsylvania-Upper Delaware Valley Interstate Air Quality Control Region.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Northeast Pennsylvania-Upper Delaware... Designation of Air Quality Control Regions § 81.55 Northeast Pennsylvania-Upper Delaware Valley Interstate Air Quality Control Region. The Northeast Pennsylvania-Upper Delaware Valley Interstate Air Quality Control...

  5. The double meaning of control: three-way interactions between internal resources, job control, and stressors at work.

    Science.gov (United States)

    Meier, Laurenz L; Semmer, Norbert K; Elfering, Achim; Jacobshagen, Nicola

    2008-07-01

    The Job Demand-Control model postulates that job control attenuates the effects of job demands on health and well-being. Support for this interactive effect is rather weak. Conceivably, it holds only when there is a match between job control and individual characteristics that relate to exercising control options, such as locus of control, or self-efficacy. This three-way interaction was tested in a sample of 96 service employees, with affective strain and musculoskeletal pain as dependent variables. As hypothesized, job control attenuated the effects of stressors only for people with an internal locus of control. For people with an external locus of control, job control actually predicted poorer well-being and health as stressors increased. For self-efficacy, the corresponding three-way interaction was significant with regard to affective strain. Copyright (c) 2008 APA, all rights reserved.

  6. High performance predictive current control of a three phase VSI: An ...

    Indian Academy of Sciences (India)

    ... current control of a three phase VSI: An experimental assessment ... Voltage source inverter; two level inverter; predictive current control; weighting factor ... Conventionally, for reference current tracking control in a two level VSI, the objective ...

  7. Hybridization among three native North American Canis species in a region of natural sympatry.

    Directory of Open Access Journals (Sweden)

    Frank Hailer

    2008-10-01

    Full Text Available Population densities of many species throughout the world are changing due to direct persecution as well as anthropogenic habitat modification. These changes may induce or increase the frequency of hybridization among taxa. If extensive, hybridization can threaten the genetic integrity or survival of endangered species. Three native species of the genus Canis, coyote (C. latrans, Mexican wolf (C. lupus baileyi and red wolf (C. rufus, were historically sympatric in Texas, United States. Human impacts caused the latter two to go extinct in the wild, although they survived in captive breeding programs. Morphological data demonstrate historic reproductive isolation between all three taxa. While the red wolf population was impacted by introgressive hybridization with coyotes as it went extinct in the wild, the impact of hybridization on the Texas populations of the other species is not clear.We surveyed variation at maternally and paternally inherited genetic markers (mitochondrial control region sequence and Y chromosome microsatellites in coyotes from Texas, Mexican wolves and red wolves from the captive breeding programs, and a reference population of coyotes from outside the historic red wolf range. Levels of variation and phylogenetic analyses suggest that hybridization has occasionally taken place between all three species, but that the impact on the coyote population is very small.Our results demonstrate that the factors driving introgressive hybridization in sympatric Texan Canis are multiple and complex. Hybridization is not solely determined by body size or sex, and density-dependent effects do not fully explain the observed pattern either. No evidence of hybridization was identified in the Mexican wolf captive breeding program, but introgression appears to have had a greater impact on the captive red wolves.

  8. Well-control co-ops for regional responses

    International Nuclear Information System (INIS)

    Abel, L.W.; Winchester, J.

    1996-01-01

    Oilfield exploration and production companies worldwide can benefit economically and in many other ways by participating in well-control cooperatives rather than operating alone and reacting to well control (WC) events by creating one-off equipment to respond to the event. The authors have presented details of a proposed co-op in this paper. The cost to maintain a full complement of WC equipment and retain trained personnel in a given region is prohibitive for a single company; however, cost becomes reasonable when resources are shared among an operator base of co-operating companies. Each individual operator receives the full benefit of having strong WC event response capability while paying only a portion of the cost

  9. Projections of Three-Dimensional Regions

    Science.gov (United States)

    Martinez, Felix; Rosa, De La

    2005-01-01

    When first-year calculus students are interested in studying double integrals, they can find, in standard textbooks, a detailed description of the different regions of integration. The aims of this paper are: to give a criterion to select the plane that will be projected, to classify the projections, and to give a simple rule to obtain them.…

  10. Applications of chaos control techniques to a three-species food chain

    International Nuclear Information System (INIS)

    Gomes, A.A.; Manica, E.; Varriale, M.C.

    2008-01-01

    We achieve control of deterministic chaos in an ecosystem model, involving three first-order nonlinear differential equations with a control parameter, recently proposed by Hastings and Powell (HP) in order to describe the dynamical behavior of a three-species food chain. After identifying a chaotic attractor corresponding to a particular value of the parameter of this ecological model, we locate periodic saddle orbits embedded in it. By applying the Ott-Grebogi-Yorke (OGY) method of controlling chaos, which introduces small time-dependent perturbations on the system parameter, we stabilize two of the saddle orbits. Furthermore, we check the versatility of the OGY method, as the system behavior is allowed to switch between 'no control' and 'control' about one or other of different stabilized periodic orbits

  11. Control of water infiltration into near surface LLW disposal units. Progress report on field experiments at a humid region site, Beltsville, Maryland: Volume 7

    International Nuclear Information System (INIS)

    Schulz, R.K.; Ridky, R.W.; O'Donnell, E.

    1994-12-01

    The project objective is to assess means for controlling waste infiltration through waste disposal unit covers in humid regions. Experimental work is being performed in large scale lysimeters (70 ft x 45 ft x 10 ft) at Beltsville, MD and results of the assessment are applicable to disposal of LLW, uranium mill tailings, hazardous waste, and sanitary landfills. Three concepts are under investigation: (1) resistive layer barrier, (2) conductive layer barrier, and bioengineering water management. The resistive layer barrier consists of compacted earth (clay). The conductive layer barrier is a special case of the capillary barrier and it requires a flow layer (e.g. fine sandy loam) over a capillary break. As long as unsaturated conditions are maintained water is conducted by the flow layer to below the waste. This barrier is most efficient at low flow rates and is thus best placed below a resistive layer barrier. Such a combination of the resistive layer over the conductive layer barrier promises to be highly effective provided there is no appreciable subsidence. Bioengineering water management is a surface cover that is designed to accommodate subsidence. It consists of impermeable panels which enhance run-off and limit infiltration. Vegetation is planted in narrow openings between panels to transpire water from below the panels. This system has successfully dewatered two lysimeters thus demonstrating that this procedure could be used for remedial action (drying out) existing water-logged disposal sites at low cost

  12. The Relationship Between Emotional Intelligence and Couples Marital Satisfaction in Three Regions of the Isfahan

    Directory of Open Access Journals (Sweden)

    زهره نصیری زارچ

    2016-02-01

    Full Text Available This study aims to thoroughly investigate the relationship between emotional intelligence and couples satisfaction performed in three regions of the Isfahan city. The research design was a descriptive correlative and the statistical population of the study consisted of all married couples who had at least one child in third grade of primary schools and from socioeconomic conditions point of view lived in rich, semi-rich and under rich areas of the city. In the research 318 samples (159 couples were chosen using random Multi-stage cluster sampling. the research aim was fundamentally based on two standard questionnaires of Bar-On emotional intelligence and ENRICH marital satisfaction. The data was analyzed using Pearson correlation method, t-test, stepwise regression. The result analysis showed that in the rich area of the components self-esteem, empathy and impulse control, in the semi-rich area Happiness, Stress Tolerance, Assertiveness, reality testing, flexibility, independence, interpersonal relationship, optimism, impulse control and problem solving and in the under rich area while Stress Tolerance and Assertiveness are the most  predictive power, in under rich area. the most significant point of the survey shows that assertiveness, reality testing, impulse control and interpersonal relationships have reversed effects, in the semi-rich area. Considering the result of the study shows that some other major factors influence couples satisfaction as well as emotional intelligence and nowadays, in the modern society satisfying providing couples satisfaction, highly depends on other social economic factor.

  13. Three-dimensional helical (spiral) CT angiography. Visualization of vessels in the maxillofacial regions

    International Nuclear Information System (INIS)

    Hanawa, Shigeo; Sakamoto, Hidetomo; Mori, Shin-ichiro; Kagawa, Toyohiro; Seze, Ryosuke; Ishioka, Hisakazu; Tashiro, Himiko; Ogawa, Kazuhisa; Wada, Tadako

    1998-01-01

    Authors performed the contrast helical CT for tumors on the maxillofacial regions, and reconstituted these data into the three-dimensional helical (spiral) CT angiography (CTA). Furthermore the conditions of photographing and the clinical significance of CTA were discussed. The subjects were 24 cases (including 13 of malignant tumors, 4 of benign tumors, 4 of inflammation and 3 of malformations), to which the contrast helical CT was performed transvenously. The photographing condition was set in principal to 140 kV of the tube voltage, 160 (200) mA of the tube current, 3 mm of the X-ray beam width, 3 mm/sec (pitch=1) of the turn-table moving speed. The relationship between the beam width and the pitch was determined by the phantom experiments. The scanning was carried out maximally for continuous 60 sec as the scanning time of a turn/sec. Of all cases, CTA visualized three-dimensionally vessels, but it was hard in the total carotid arteries and the internal-external carotid arteries. Authors analyzed the axial and the multiplanar reconstitution (MPR) images as the two-dimensional display, and the surface rendering (SR), the volume rendering and the maximum intensity projections (MIP) as the three-dimensional display. The axial and MPR image of the facial arteries and the lingual arteries as the branched vessels from the external carotid arteries were recognized easily. By SR, it was easily to understand the anatomical relationship among vessels, gnathic bone and cervical vertebrae, and by MIP sufficiently observe the concentration dependent calcification of the vessel walls. Three-dimensional CTA is very useful to get the three-dimensional visual information about the anatomical structures of the maxillofacial regions which is necessary for oral surgeons to plan the pre-operational strategies. (K.H.)

  14. Regional surface geometry of the rat stomach based on three-dimensional curvature analysis

    Energy Technology Data Exchange (ETDEWEB)

    Liao Donghua [Center of Excellence in Visceral Biomechanics and Pain, Aalborg Hospital, DK-9100 Aalborg (Denmark); Zhao Jingbo [Center of Excellence in Visceral Biomechanics and Pain, Aalborg Hospital, DK-9100 Aalborg (Denmark); Gregersen, Hans [Center of Excellence in Visceral Biomechanics and Pain, Aalborg Hospital, DK-9100 Aalborg (Denmark)

    2005-01-21

    A better understanding of gastric accommodation and gastric perception requires knowledge of regional gastric geometry and local gastric tension throughout the stomach. An analytic method based on medical imaging data was developed in this study to describe the three-dimensional (3D) rat stomach geometry and tension distribution. The surface principal radii of curvatures were simulated and the surface tension was calculated in the glandular and non-glandular region of the stomach at pressures from 0 Pa to 800 Pa. The radii of curvature and tension distribution in the stomach were non-homogeneous. The radii of curvature in the glandular stomach were larger than those in the non-glandular region at pressures less than 100 Pa (P < 0.001). When the pressure increased to more than 200 Pa, the radii of curvature in the non-glandular stomach was larger than in the glandular stomach (P < 0.05). The curvature and tension distribution mapping using medical imaging technology and 3D models can be used to characterize and distinguish the physical behaviour in separate regions of the stomach.

  15. Regional surface geometry of the rat stomach based on three-dimensional curvature analysis

    International Nuclear Information System (INIS)

    Liao Donghua; Zhao Jingbo; Gregersen, Hans

    2005-01-01

    A better understanding of gastric accommodation and gastric perception requires knowledge of regional gastric geometry and local gastric tension throughout the stomach. An analytic method based on medical imaging data was developed in this study to describe the three-dimensional (3D) rat stomach geometry and tension distribution. The surface principal radii of curvatures were simulated and the surface tension was calculated in the glandular and non-glandular region of the stomach at pressures from 0 Pa to 800 Pa. The radii of curvature and tension distribution in the stomach were non-homogeneous. The radii of curvature in the glandular stomach were larger than those in the non-glandular region at pressures less than 100 Pa (P < 0.001). When the pressure increased to more than 200 Pa, the radii of curvature in the non-glandular stomach was larger than in the glandular stomach (P < 0.05). The curvature and tension distribution mapping using medical imaging technology and 3D models can be used to characterize and distinguish the physical behaviour in separate regions of the stomach

  16. Analytical solutions for benchmarking cold regions subsurface water flow and energy transport models: one-dimensional soil thaw with conduction and advection

    Science.gov (United States)

    Kurylyk, Barret L.; McKenzie, Jeffrey M; MacQuarrie, Kerry T. B.; Voss, Clifford I.

    2014-01-01

    Numerous cold regions water flow and energy transport models have emerged in recent years. Dissimilarities often exist in their mathematical formulations and/or numerical solution techniques, but few analytical solutions exist for benchmarking flow and energy transport models that include pore water phase change. This paper presents a detailed derivation of the Lunardini solution, an approximate analytical solution for predicting soil thawing subject to conduction, advection, and phase change. Fifteen thawing scenarios are examined by considering differences in porosity, surface temperature, Darcy velocity, and initial temperature. The accuracy of the Lunardini solution is shown to be proportional to the Stefan number. The analytical solution results obtained for soil thawing scenarios with water flow and advection are compared to those obtained from the finite element model SUTRA. Three problems, two involving the Lunardini solution and one involving the classic Neumann solution, are recommended as standard benchmarks for future model development and testing.

  17. An assessment of the Pacific Regional Cancer Coalition: outcomes and implications of a regional coalition internal and external assessment.

    Science.gov (United States)

    Sy, Angela U; Heckert, Karen A; Buenconsejo-Lum, Lee; Hedson, Johnny; Tamang, Suresh; Palafox, Neal

    2011-11-01

    The Pacific Regional Cancer Coalition (PRCC) provides regional leadership in the U.S. Affiliated Pacific Islands (USAPI) to implement the Regional Comprehensive Control Plan: 2007-2012, and to evaluate its coalition and partnerships. The Pacific Center of Excellence in the Elimination of Disparities (CEED), aims to reduce cancer disparities and conducts evaluation activities relevant to cancer prevention and control in the USAPI. The PRCC Self (internal) and Partner (external) Assessments were conducted to assess coalition functioning, regional and national partnerships, sustainability, and the role of regionalism for integrating all chronic disease prevention and control in the Pacific. Self-administered questionnaires and key informant telephone interviews with PRCC members (N=20), and representatives from regional and national partner organizations were administered (N=26). Validated multi item measures using 5-point scales on coalition and partnership characteristics were used. Chronbach's alphas and averages for the measures were computed. Internal coalition measures: satisfaction (4.2, SD=0.48) communication (4.0, SD=0.56), respect (4.0, SD=0.60) were rated more highly than external partnership measures: resource sharing (3.5, SD=0.74), regionalism (3.9, SD=0.47), use of findings (3.9, SD=0.50). The PRCC specifically identified its level of "collaboration" with external partners including Pacific CEED. External partners identified its partnership with the PRCC in the "coalition" stage. PRCC members and external partners are satisfied with their partnerships. All groups should continue to focus on building collaboration with partners to reflect a truly regional approach to sustain the commitment, the coalitions and the programming to reduce cancer in the USAPI. PRCC and partners should also work together to integrate all chronic disease prevention and control efforts in the Pacific.

  18. Novel electrical transport properties in conducting polymers such as polythiophene and Poly(3-Methylthiophene)

    International Nuclear Information System (INIS)

    Kazama, Shigeo; Masubuchi, Shin-ichi; Matsuyama, Tomochika; Matsushita, Rokuji.

    1994-01-01

    Electric transport properties in most of the conducting organic polymers have provided a riddle that prevents a thorough physical understanding of the conduction mechanism. Major difficulties for approaching the most substantial aspect in the electrical transport properties underlie in complicated higher order structure inherent to polymeric materials consisting of crystalline regions entangled with disordered amorphous regions. In order to clearly understand the origin of the metallic nature of conducting polymers, we have to extract the proper transport properties characteristics of the ordered crystalline regions. We have made a series of experimental studies of the transport properties in conductive polythiophene and poly(3-methylthiophene) obtained with the electrochemical polymerization. For polythiophene, we have investigated both the as-grown samples and the ones that contain controlled amount of dopant species exchanged after the neutralization aiming to see the effect of dopant concentration on the transport properties. (author)

  19. Direct-current vector control of three-phase grid-connected rectifier-inverter

    Energy Technology Data Exchange (ETDEWEB)

    Li, Shuhui; Haskew, Timothy A.; Hong, Yang-Ki; Xu, Ling [Department of Electrical and Computer Engineering, University of Alabama, Tuscaloosa, AL 35475 (United States)

    2011-02-15

    The three-phase grid-connected converter is widely used in renewable and electric power system applications. Traditionally, control of the three-phase grid-connected converter is based on the standard decoupled d-q vector control mechanism. Nevertheless, the study of this paper shows that there is a limitation in the conventional standard vector control method. Some of the limitations have also been found recently by other researchers. To overcome the shortage of the conventional vector control technique, this paper proposes a new direct-current d-q vector control mechanism in a nested-loop control structure, based on which an optimal control strategy is developed in a nonlinear programming formulation. The behaviors of both the conventional and proposed control methods are compared and evaluated in simulation and laboratory hardware experiment environments, both of which demonstrates that the proposed approach is effective for grid-connected power converter control in a wide system conditions while the conventional standard vector control approach may behave improperly especially when the converter operates beyond its PWM saturation limit. (author)

  20. Three-dimensional hydrogeologic framework model for use with a steady-state numerical ground-water flow model of the Death Valley regional flow system, Nevada and California

    International Nuclear Information System (INIS)

    Belcher, W.R.; Faunt, C.C.; D'Agnese, F.A.

    2002-01-01

    The U.S. Geological Survey, in cooperation with the Department of Energy and other Federal, State, and local agencies, is evaluating the hydrogeologic characteristics of the Death Valley regional ground-water flow system. The ground-water flow system covers and area of about 100,000 square kilometers from latitude 35 degrees to 38 degrees 15 minutes North to longitude 115 degrees to 118 degrees West, with the flow system proper comprising about 45,000 square kilometers. The Death Valley regional ground-water flow system is one of the larger flow systems within the Southwestern United States and includes in its boundaries the Nevada Test Site, Yucca Mountain, and much of Death Valley. Part of this study includes the construction of a three-dimensional hydrogeologic framework model to serve as the foundation for the development of a steady-state regional ground-water flow model. The digital framework model provides a computer-based description of the geometry and composition of the hydro geologic units that control regional flow. The framework model of the region was constructed by merging two previous framework models constructed for the Yucca Mountain Project and the Environmental Restoration Program Underground Test Area studies at the Nevada Test Site. The hydrologic characteristics of the region result from a currently arid climate and complex geology. Interbasinal regional ground-water flow occurs through a thick carbonate-rock sequence of Paleozoic age, a locally thick volcanic-rock sequence of Tertiary age, and basin-fill alluvium of Tertiary and Quaternary age. Throughout the system, deep and shallow ground-water flow may be controlled by extensive and pervasive regional and local faults and fractures. The framework model was constructed using data from several sources to define the geometry of the regional hydrogeologic units. These data sources include (1) a 1:250,000-scale hydrogeologic-map compilation of the region; (2) regional-scale geologic cross

  1. Local-regional control in breast cancer patients with a possible genetic predisposition

    International Nuclear Information System (INIS)

    Freedman, Laura M.; Buchholz, Thomas A.; Thames, Howard D.; Strom, Eric A.; McNeese, Marsha D.; Hortobagyi, Gabriel N.; Singletary, S. Eva; Heaton, Keith M.; Hunt, Kelly K.

    2000-01-01

    Purpose: Local control rates for breast cancer in genetically predisposed women are poorly defined. Because such a small percentage of breast cancer patients have proven germline mutations, surrogates, such as a family history for breast cancer, have been used to examine this issue. The purpose of this study was to evaluate local-regional control following breast conservation therapy (BCT) in patients with bilateral breast cancer and a breast cancer family history. Methods and Materials: We retrospectively reviewed records of all 58 patients with bilateral breast cancer and a breast cancer family history treated in our institution between 1959 and 1998. The primary surgical treatment was a breast-conserving procedure in 55 of the 116 breast cancer cases and a mastectomy in 61. The median follow-up was 68 months for the BCT patients and 57 months for the mastectomy-treated patients. Results: Eight local-regional recurrences occurred in the 55 cases treated with BCT, resulting in 5- and 10-year actuarial local-regional control rates of 86% and 76%, respectively. In the nine cases that did not receive radiation as a component of their BCT, four developed local-regional recurrences (5- and 10-year local-regional control rates of BCT without radiation: 49% and 49%). The 5- and 10-year actuarial local-regional control rates for the 46 cases treated with BCT and radiation were 94% and 83%, respectively. In these cases, there were two late local recurrences, developing at 8 years and 9 years, respectively. A log rank comparison of radiation versus no radiation actuarial data was significant at p = 0.009. In the cases treated with BCT, a multivariate analysis of radiation use, patient age, degree of family history, margin status, and stage revealed that only the use of radiation was associated with improved local control (Cox regression analysis p = 0.021). The 10-year actuarial rates of local-regional control following mastectomy with and without radiation were 91% and 89

  2. Three cases of Capnocytophaga canimorsus meningitis seen at a regional hospital in one year

    DEFF Research Database (Denmark)

    Monrad, Rikke Nygaard; Hansen, Dennis Schrøder

    2012-01-01

    Three cases of meningitis caused by the fastidious Gram-negative rod Capnocytophaga canimorsus have been observed at a regional hospital in 1 y. The difficulties connected with the correct diagnosis by classical culturing methods in contrast to molecular methods, as well as possible reasons...

  3. Improved control strategy for the three-phase grid-connected inverter

    DEFF Research Database (Denmark)

    Yao, Zhilei; Xiao, Lan; Guerrero, Josep M.

    2015-01-01

    An improved control strategy for the three-phase grid-connected inverter with space vector pulse width modulation (SVPWM) is proposed. When the grid current contains harmonics, the d- and q-axis grid currents will be interacted, and then the waveform quality of the grid current will be poorer....... As the reference output voltage cannot directly reflect the change of the reference grid current, the dynamic response of the grid-connected inverter is slow. In order to solve the aforementioned problems, the d- and q-axis grid currents in the decoupled components of the grid current controller can be substituted...... by the d- and q-axis reference grid currents, respectively. The operating principles of the traditional and proposed control methods are illustrated. Experimental results for a 15-kVA three-phase grid-connected inverter with SVPWM verify the theoretical analysis. Compared with the traditional control...

  4. Genetic characterization of UCS region of Pneumocystis jirovecii and construction of allelic profiles of Indian isolates based on sequence typing at three regions.

    Science.gov (United States)

    Gupta, Rashmi; Mirdha, Bijay Ranjan; Guleria, Randeep; Kumar, Lalit; Luthra, Kalpana; Agarwal, Sanjay Kumar; Sreenivas, Vishnubhatla

    2013-01-01

    Pneumocystis jirovecii is an opportunistic pathogen that causes severe pneumonia in immunocompromised patients. To study the genetic diversity of P. jirovecii in India the upstream conserved sequence (UCS) region of Pneumocystis genome was amplified, sequenced and genotyped from a set of respiratory specimens obtained from 50 patients with a positive result for nested mitochondrial large subunit ribosomal RNA (mtLSU rRNA) PCR during the years 2005-2008. Of these 50 cases, 45 showed a positive PCR for UCS region. Variations in the tandem repeats in UCS region were characterized by sequencing all the positive cases. Of the 45 cases, one case showed five repeats, 11 cases showed four repeats, 29 cases showed three repeats and four cases showed two repeats. By running amplified DNA from all these cases on a high-resolution gel, mixed infection was observed in 12 cases (26.7%, 12/45). Forty three of 45 cases included in this study had previously been typed at mtLSU rRNA and internal transcribed spacer (ITS) region by our group. In the present study, the genotypes at those two regions were combined with UCS repeat patterns to construct allelic profiles of 43 cases. A total of 36 allelic profiles were observed in 43 isolates indicating high genetic variability. A statistically significant association was observed between mtLSU rRNA genotype 1, ITS type Ea and UCS repeat pattern 4. Copyright © 2012 Elsevier B.V. All rights reserved.

  5. Structures and ion conduction pathways of amorphous lithium ion conductors

    International Nuclear Information System (INIS)

    Mori, Kazuhiro; Fukunaga, Toshiharu; Onodera, Yohei

    2014-01-01

    For ( 7 Li 2 S) x (P 2 S 5 ) 100-x glasses (x = 50, 60, and 70) and 7 Li 7 P 3 S 11 metastable crystal, time-of-flight neutron diffraction and synchrotron X-ray diffraction experiments were performed, and three-dimensional structures and conduction pathways of lithium ions were studied using the reverse Monte Carlo (RMC) modeling and the bond valence sum (BVS) approach. The conduction pathways of the lithium ions could be classified into two types: lithium 'stable' and 'metastable' regions, respectively. Moreover, it was found that there is a significant relationship between the activation energy of the electrical conduction and the topology of the conduction pathways of the lithium ions. (author)

  6. Three decades of BGR airborne geophysical surveys over the polar regions - a review

    Science.gov (United States)

    Damaske, Detlef

    2013-04-01

    The Federal Institute for Geosciences and Natural Resources (BGR) has been conducting geological polar research since 1979. A few years later BGR engaged in airborne geophysical projects. Investigation of the lithosphere of the continent and the continental margins was one of the key issues for BGR. Right from the beginning geophysical research was closely associated with the geological activities. The GANOVEX (German Antarctic North Victoria Land Expedition) program combined geological research with geophysical (mainly airborne) investigations. This proved to be a fruitful approach to many of the open questions regarding the tectonic development of the Ross Sea region. Aeromagnetic surveys evolved into a powerful tool for identifying geological structures and following them underneath the ice covered areas - not accessible to direct geological investigations. To achieve this aim it was essential to lay out these surveys with a relatively closely spaced line separation on the expense of covering large areas at the same time. Nevertheless, over many years of continues research areas of more than a just regional extent could be covered. This was, however, only possible through international collaboration. During the first years, working in the Ross Sea area, the cooperation with the US and Italian programs played a significant role, especially the GITARA (German-Italian Aeromagnetic Research in Antarctica) program has to be mentioned. GEOMAUD (Geoscientific Expedition to Dronning Maud Land) and the German-Australian joint venture PCMEGA (Prince Charles Mountains Expedition of Germany & Australia) expanded research activities to the East Antarctic shield area. In the International Polar Year (IPY), BGR played a leading role in the international project AGAP (Antarctica's GAmburtsev Province) as part of the main topic "Venture into Unknown Regions". AGAP was jointly conducted by the USA, Great Britain, Australia, China and Germany. While in the Ross Sea area even

  7. Multidimensional Heat Conduction

    DEFF Research Database (Denmark)

    Rode, Carsten

    1998-01-01

    Analytical theory of multidimensional heat conduction. General heat conduction equation in three dimensions. Steay state, analytical solutions. The Laplace equation. Method of separation of variables. Principle of superposition. Shape factors. Transient, multidimensional heat conduction....

  8. Three-Phase Grid-Connected of Photovoltaic Generator Using Nonlinear Control

    DEFF Research Database (Denmark)

    Yahya, A.; El Fadil, H.; Guerrero, Josep M.

    2014-01-01

    This paper proposes a nonlinear control methodology for three phase grid connected of PV generator. It consists of a PV arrays; a voltage source inverter, a grid filter and an electric grid. The controller objectives are threefold: i) ensuring the Maximum power point tracking (MPPT) in the side...... stability analysis and simulation results that the proposed controller meets all the objectives....

  9. A high-fidelity model for coupling flow and mechanical deformation of the porous paper web - a key to improved understanding of dewatering and rewet at the press section in paper making

    Energy Technology Data Exchange (ETDEWEB)

    Hao, Y. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Trebotich, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Wang, W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Xu, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Turpin, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2017-04-05

    The U.S. pulp and paper industry is the third-largest manufacturing user of energy, with an energy demand of 2,540 trillion Btu in 2010. Within the papermaking process, drying consumes over 400 trillion Btu annually which makes it one of the largest energy saving opportunities. In the 2014 Forest Products Industry Technology Roadmap, it is concluded that increasing the paper web solid content entering the dryer section from the current 45- 55 percent to approaching 65 percent, which would save 1.0 MMBtu per ton or 20 percent of the energy used in drying, is one of the most needed technology breakthroughs to achieve a more sustainable approach for manufacturing pulp and paper products. Achieving such significant energy savings highly depends on understanding the fundamental dynamics of the wet press process and then developing optimized solutions for design of more energy-efficient press processes and equipment. The objective of this project is to develop reliable computational capabilities to accurately simulate the flow of water from/to the porous pulp medium (dewatering/rewetting) during the pressing process in paper making.

  10. Mitochondrial DNA control region variability in wild boars from west Balkans

    Directory of Open Access Journals (Sweden)

    Đan Mihajla

    2013-01-01

    Full Text Available The wild boar (Sus scrofa is one of most abundant game species in hunting areas of Balkan region. The large fraction of pre-glacial genetic diversity in wild boar populations from the Balkans was addressed due to high proportion of unique mtDNA haplotypes found in Greece, indicating Balkan as main refugial area for wild boars. The aim of the present study is to characterize mitochondrial DNA control region variability in wild boars from different areas in the West Balkan region, in order to evaluate level of genetic variability, to detect unique haplotypes and to infer possible structuring. The total number of 163 individuals from different sampling localities were included in the study. A fragment of the mtDNA control region was amplified and sequenced by standard procedures. Population genetic analyses were performed using several computer packages: BioEdit, ARLEQUIN 3.5.1.2., Network 4.6.0.0 and MEGA5. Eleven different haplotypes were identified and haplotype diversity was 0.676, nucleotide diversity 0.0026, and the average number of nucleotide differences (k 1.169. The mismatch distribution and neutrality tests indicated the expansion of the all populations. It is shown that high level of genetic diversity is present in the wild boars from the West Balkan region and we have managed to detect regional unique haplotypes in high frequency. Genetic diversity differences have been found in regional wild boar groups, clustering them in two main clusters, but further speculations on the reasons for the observed clustering are prevented due to restricted informativness of the single locus marker. Obtained knowledge of genetic variation in the wild boar may be relevant for improving knowledge of the phylogeny and phylogeography of the wild boars, but as well as for hunting societies and responsible authorities for the effective control of wild boar populations.

  11. Radiotherapy is associated with significant improvement in local and regional control in Merkel cell carcinoma

    International Nuclear Information System (INIS)

    Kang, Susan H; Haydu, Lauren E; Goh, Robin Yeong Hong; Fogarty, Gerald B

    2012-01-01

    Merkel cell carcinoma (MCC) is a rare tumour of skin. This study is a retrospective audit of patients with MCC from St Vincent’s and Mater Hospital, Sydney, Australia. The aim of this study was to investigate the influence of radiotherapy (RT) on the local and regional control of MCC lesions and survival of patients with MCC. The data bases in anatomical pathology, RT and surgery. We searched for patients having a diagnosis of MCC between 1996 and 2007. Patient, tumour and treatment characteristics were collected and analysed. Univariate survival analysis of categorical variables was conducted with the Kaplan-Meier method together with the Log-Rank test for statistical significance. Continuous variables were assessed using the Cox regression method. Multivariate analysis was performed for significant univariate results. Sixty seven patients were found. Sixty two who were stage I-III and were treated with radical intent were analysed. 68% were male. The median age was 74 years. Forty-two cases (68%) were stage I or II, and 20 cases (32%) were stage III. For the subset of 42 stage I and II patients, those that had RT to their primary site had a 2-year local recurrence free survival of 89% compared with 36% for patients not receiving RT (p<0.001). The cumulative 2-year regional recurrence free survival for patients having adjuvant regional RT was 84% compared with 43% for patients not receiving this treatment (p<0.001). Immune status at initial surgery was a significant predictor for OS and MCCSS. In a multivariate analysis combining macroscopic size (mm) and immune status at initial surgery, only immune status remained a significant predictor of overall survival (HR=2.096, 95% CI: 1.002-4.385, p=0.049). RT is associated with significant improvement in local and regional control in Merkel cell carcinoma. Immunosuppression is an important factor in overall survival

  12. Region-Urbanicity Differences in Locus of Control: Social Disadvantage, Structure, or Cultural Exceptionalism?

    Science.gov (United States)

    Shifrer, Dara; Sutton, April

    2014-11-01

    People with internal rather than external locus of control experience better outcomes in multiple domains. Previous studies on spatial differences in control within America only focused on the South, relied on aggregate level data or historical evidence, or did not account for other confounding regional distinctions (such as variation in urbanicity). Using data from the National Education Longitudinal Study, we find differences in adolescents' loci of control depending on their region and urbanicity are largely attributable to differences in their social background, and only minimally to structural differences (i.e., differences in the qualities of adolescents' schools). Differences that persist net of differences across adolescents and their schools suggest the less internal control of rural Southern adolescents, and the more internal control of rural and urban Northeastern adolescents, may be due to cultural distinctions in those areas. Results indicate region is more closely associated than urbanicity with differences in locus of control, with Western and Northeastern cultures seemingly fostering more internal control than Midwestern and Southern cultures. These findings contribute to research on spatial variation in a variety of psychological traits.

  13. Common Versus Specific Correlates of Fifth-Grade Conduct Disorder and Oppositional Defiant Disorder Symptoms: Comparison of Three Racial/Ethnic Groups.

    Science.gov (United States)

    Wiesner, Margit; Elliott, Marc N; McLaughlin, Katie A; Banspach, Stephen W; Tortolero, Susan; Schuster, Mark A

    2015-07-01

    The extent to which risk profiles or correlates of conduct disorder (CD) and oppositional defiant disorder (ODD) symptoms overlap among youth continues to be debated. Cross-sectional data from a large, representative community sample (N = 4,705) of African-American, Latino, and White fifth graders were used to examine overlap in correlates of CD and ODD symptoms. About 49 % of the children were boys. Analyses were conducted using negative binomial regression models, accounting for several confounding factors (e.g., attention deficit/hyperactivity disorder symptoms), sampling weights, stratification, and clustering. Results indicated that CD and ODD symptoms had very similar correlates. In addition to previously established correlates, several social skills dimensions were significantly related to ODD and CD symptoms, even after controlling for other correlates. In contrast, temperamental dimensions were not significantly related to CD and ODD symptoms, possibly because more proximal correlates (e.g., social skills) were also taken into account. Only two factors (gender and household income) were found to be specific correlates of CD, but not ODD, symptoms. The pattern of common and specific correlates of CD and ODD symptoms was replicated fairly consistently across the three racial/ethnic subgroups. Implications of these findings for further research and intervention efforts are discussed.

  14. Reducing child conduct problems and promoting social skills in a middle-income country: cluster randomised controlled trial†

    Science.gov (United States)

    Baker-Henningham, Helen; Scott, Stephen; Jones, Kelvyn; Walker, Susan

    2012-01-01

    Background There is an urgent need for effective, affordable interventions to prevent child mental health problems in low- and middle-income countries. Aims To determine the effects of a universal pre-school-based intervention on child conduct problems and social skills at school and at home. Method In a cluster randomised design, 24 community pre-schools in inner-city areas of Kingston, Jamaica, were randomly assigned to receive the Incredible Years Teacher Training intervention (n = 12) or to a control group (n = 12). Three children from each class with the highest levels of teacher-reported conduct problems were selected for evaluation, giving 225 children aged 3–6 years. The primary outcome was observed child behaviour at school. Secondary outcomes were child behaviour by parent and teacher report, child attendance and parents’ attitude to school. The study is registered as ISRCTN35476268. Results Children in intervention schools showed significantly reduced conduct problems (effect size (ES) = 0.42) and increased friendship skills (ES = 0.74) through observation, significant reductions to teacher-reported (ES = 0.47) and parent-reported (ES = 0.22) behaviour difficulties and increases in teacher-reported social skills (ES = 0.59) and child attendance (ES = 0.30). Benefits to parents’ attitude to school were not significant. Conclusions A low-cost, school-based intervention in a middle-income country substantially reduces child conduct problems and increases child social skills at home and at school. PMID:22500015

  15. REGIONAL DRAINWATER MANAGEMENT: SOURCE CONTROL, AGROFORESTRY, AND EVAPORATION PONDS

    OpenAIRE

    Posnikoff, Judith F.; Knapp, Keith C.

    1996-01-01

    Source control is one way to address salinity and drainage problems in irrigated agriculture, and reuse of drainage flows on salt-tolerant crops or trees in agroforestry production is another. A regional model of agricultural production with drainwater reuse and disposal is developed. Deep percolation flows are controlled through choice of crop areas, irrigation systems, and applied-water quantities. Crop drainwater may by reused in agroforestry production, and residual emissions are disposed...

  16. The semiquantitative three-phase bone scintigraphy on hemiplegic patients with earlier complex regional pain syndrome

    International Nuclear Information System (INIS)

    Li Fang; Liu Xingdang; Lu Zhihui; Liu Congjin

    2010-01-01

    Objective: To investigate the difference between the early phases and delay phase of three-phase bone scintigraphy on hemiplegic patients with earlier complex regional pain syndrome (CRPS). Methods: Twenty-nine stroke patients with hemiplegia complicating CRPS received three-phase bone scintigraphy after intravenous injection of 99 Tc m -methylene diphosphonate (MDP). The region of interest (ROI) technique was used to obtain the radioactive counts of involved joints and contralateral sites on wrists, metacarpophalangeal, proximal interphalangeal and distal interphalangeal joints. The total counts of these four sites in each patient were then obtained and the total uptake ratios of involved joints/contralateral joints for each phase were calculated to compare the difference among the three phases. Wilcoxon test and ANOVA were used in data analyses. Results: The involved joints of hemiplegic side displayed higher tracer uptake. There were significant differences of the radioactive counts between involved joints and uninvolved ones in the perfusion, pool and delay phase (Wilcoxon test, Z: -4.73 to -2.10, P<0.05). There was no significant difference of total uptake ratios of involved joints/contralateral joints among the three phases (ANOVA, F = 0. 807, P < 0.05). Conclusions: Due to higher bone seeking agent accumulation on three-phase bone scintigraphy, both early phases and delay phase imaging showed similar value in stroke patients with hemiplegia complicating earlier CRPS. (authors)

  17. Bacterial regrowth potential in alkaline sludges from open-sun and covered sludge drying beds

    Energy Technology Data Exchange (ETDEWEB)

    Alkan, U.; Topac, F.O.; Birden, B.; Baskaya, H.S. [Uludag University, Gorukle (Turkey). Dept. of Environmnetal Engineering

    2007-10-15

    The aim of this study was to compare the regrowth potentials of wastewater sludges dried in two pilot-scale drying processes namely, Open-Sun Sludge Drying Bed (OSDB) and Covered Sludge Drying Bed (CSDB). Quicklime and/or coal fly ash were added to raw sludge samples prior to drying processes in order to enhance bacterial inactivation. Following three drying cycles (March-April, June-July and August-October), sludge samples were taken from the beds for the regrowth experiments. Addition of alkaline materials prevented the regrowth of faecal coliforms in all rewetted samples except for the samples obtained after the rainfall events in OSDB. Rewetting of these samples in the regrowth experiments increased faecal coliform numbers by 3.5-7 log units. In contradiction, the observed bacterial numbers in rewetted alkaline samples from CSDB were below the EPA Class B criterion (2 million MPN g{center_dot} 1) dry sludge). The combination of additional heat from solar collectors, protection from the rain and the unfavourable living conditions owing to alkaline materials appeared to inactivate bacteria more effectively in CSDB and hence eliminated regrowth potential more efficiently.

  18. Electrohydromechanical analysis based on conductivity gradient in microchannel

    International Nuclear Information System (INIS)

    Jiang Hongyuan; Ren Yukun; Ao Hongrui; Ramos, Antonio

    2008-01-01

    Fluid manipulation is very important in any lab-on-a-chip system. This paper analyses phenomena which use the alternating current (AC) electric field to deflect and manipulate coflowing streams of two different electrolytes (with conductivity gradient) within a microfluidic channel. The basic theory of the electrohydrodynamics and simulation of the analytical model are used to explain the phenomena. The velocity induced for different voltages and conductivity gradient are computed. The results show that when the AC electrical signal is applied on the electrodes, the fluid with higher conductivity occupies a larger region of the channel and the interface of the two fluids is deflected. It will provide some basic reference for people who want to do more study in the control of different fluids with conductivity gradient in a microfluidic channel. (classical areas of phenomenology)

  19. Diffraction limited focusing with controllable arbitrary three-dimensional polarization

    International Nuclear Information System (INIS)

    Chen, Weibin; Zhan, Qiwen

    2010-01-01

    We propose a new approach that enables full control over the three-dimensional state of polarization and the field distribution near the focus of a high numerical aperture objective lens. By combining the electric dipole radiation and a vectorial diffraction method, the input field at the pupil plane for generating arbitrary three-dimensionally oriented linear polarization at the focal point with a diffraction limited spot size is found analytically by solving the inverse problem. Arbitrary three-dimensional elliptical polarization can be obtained by introducing a second electric dipole oriented in the orthogonal plane with appropriate amplitude and phase differences

  20. Seismic risk control of nuclear power plants using seismic protection systems in stable continental regions: The UK case

    Energy Technology Data Exchange (ETDEWEB)

    Medel-Vera, Carlos, E-mail: cbmedel@uc.cl; Ji, Tianjian, E-mail: tianjian.ji@manchester.ac.uk

    2016-10-15

    Highlights: • Strategies to reduce seismic risk for nuclear power stations in the UK are analysed. • Efficiency of devices to reduce risk: viscous-based higher than hysteretic-based. • Scenario-based incremental dynamic analysis is introduced for use in nuclear stations. • Surfaces of seismic unacceptable performance for nuclear stations are proposed. - Abstract: This article analyses three different strategies on the use of seismic protection systems (SPS) for nuclear power plants (NPPs) in the UK. Such strategies are based on the experience reported elsewhere of seismically protected nuclear reactor buildings in other stable continental regions. Analyses are conducted using an example of application based on a 1000 MW Pressurised Water Reactor building located in a representative UK nuclear site. The efficiency of the SPS is probabilistically assessed to achieve possible risk reduction for both rock and soil sites in comparison with conventionally constructed NPPs. Further analyses are conducted to study how the reduction of risk changes when all controlling scenarios of the site are included. This is done by introducing a scenario-based incremental dynamic analysis aimed at the generation of surfaces for unacceptable performance of NPPs as a function of earthquake magnitude (M{sub w}) and distance-to-site (R{sub epi}). General guidelines are proposed to potentially use SPS in future NPPs in the UK. Such recommendations can be used by the British nuclear industry in the future development of 12 new reactors to be built in the next two decades to generate 16 GWe of new nuclear capacity.

  1. Processes Controlling Water Vapor in the Winter Arctic Tropopause Region

    Science.gov (United States)

    Pfister, Leonhard; Selkirk, Henry B.; Jensen, Eric J.; Padolske, James; Sachse, Glen; Avery, Melody; Schoeberl, Mark R.; Mahoney, Michael J.; Richard, Erik

    2002-01-01

    This work describes transport and thermodynamic processes that control water vapor near the tropopause during the SAGE III-Ozone Loss and Validation Experiment (SOLVE), held during the Arctic 1999/2000 winter season. Aircraft-based water vapor, carbon monoxide, and ozone measurements were analyzed so as to establish how deeply tropospheric air mixes into the Arctic lowermost stratosphere and what the implications are for cloud formation and water vapor removal in this region of the atmosphere. There are three major findings. First, troposphere-to-stratosphere exchange extends into the Arctic stratosphere to about 13 km. Penetration is to similar levels throughout the winter, however, because ozone increases with altitude most rapidly in the early spring, tropospheric air mixes with the highest values of ozone in that season. The effect of this upward mixing is to elevate water vapor mixing ratios significantly above their prevailing stratospheric values of above 5ppmv. Second, the potential for cloud formation in the stratosphere is highest during early spring, with about 20% of the parcels which have ozone values of 300-350 ppbv experiencing ice saturation in a given 10 day period. Third, during early spring, temperatures at the troposphere are cold enough so that 5-10% of parcels experience relative humidities above 100%, even if the water content is as low as 5 ppmv. The implication is that during this period, dynamical processes near the Arctic tropopause can dehydrate air and keep the Arctic tropopause region very dry during early spring.

  2. Spatial co-distribution of neglected tropical diseases in the East African Great Lakes region: revisiting the justification for integrated control

    Science.gov (United States)

    Clements, Archie C. A.; Deville, Marie-Alice; Ndayishimiye, Onésime; Brooker, Simon; Fenwick, Alan

    2010-01-01

    Summary OBJECTIVE To determine spatial patterns of co-endemicity of schistosomiasis mansoni and the soil-transmitted helminths (STHs) Ascaris lumbricoides, Trichuris trichiura and hookworm in the Great Lakes region of East Africa, to help plan integrated neglected tropical disease programmes in this region. METHOD Parasitological surveys were conducted in Uganda, Tanzania, Kenya and Burundi in 28 213 children in 404 schools. Bayesian geostatistical models were used to interpolate prevalence of these infections across the study area. Interpolated prevalence maps were overlaid to determine areas of co-endemicity. RESULTS In the Great Lakes region, prevalence was 18.1% for Schistosoma mansoni, 50.0% for hookworm, 6.8% for A. lumbricoides and 6.8% for T. trichiura. Hookworm infection was ubiquitous, whereas S. mansoni, A. lumbricoides and T. trichiura were highly focal. Most areas were endemic (prevalence ≥10%) or hyperendemic (prevalence ≥50%) for one or more STHs, whereas endemic areas for schistosomiasis mansoni were restricted to foci adjacent large perennial water bodies. CONCLUSION Because of the ubiquity of hookworm, treatment programmes are required for STH throughout the region but efficient schistosomiasis control should only be targeted at limited high-risk areas. Therefore, integration of schistosomiasis with STH control is only indicated in limited foci in East Africa. PMID:20409287

  3. A case–control study of epidemiological factors associated with leptospirosis in South Gujarat region

    Directory of Open Access Journals (Sweden)

    K T Desai

    2016-01-01

    Full Text Available Background: The current study was planned to identify the epidemiological factors associated with leptospirosis in South Gujarat region using neighborhood controls. Methods: A total of 100 cases of leptospirosis occurred in South Gujarat region during the year 2012 were selected using simple random sampling. Three neighbors of the selected cases formed the controls (n = 300. A pretested structured questionnaire was used for data collection and data were analyzed using Epi Info 2007. Results: There was significant association of illiteracy (odds ratio [OR] =1.82, 95% confidence interval [CI] =1.14–2.89, working in waterlogged fields during the reference season (OR = 4.6, 95% CI = 1.6–17.9, swimming/bathing in canals, open air defecation practices, storage of cow dung in or surrounding house, residence in the house made up of cow dung walls, households with access of food to rodents, injuries over hands/foot during the endemic season (OR = 3, 95% CI = 1.8–4.8, and history of skin disease during the endemic season (OR = 4.2, 95% CI = 2–8.5, with leptospirosis. Only 10% of individuals had gumboots for protection. A total of 83 (83% cases and 240 (80% controls had taken oral doxycycline chemoprophylaxis (P > 0.05. Cases had taken chemoprophylaxis for a median 4 weeks (range: 1–8 while controls had taken the same for median 8 weeks (range = 1–8 (P < 0.002. Conclusions: Although the commonly established factors appear to be associated with leptospirosis, the role of host factors seems to play a more important role in determining susceptibility to leptospirosis in exposed individuals.

  4. Experience with a three-axis side-located controller during a static and centrifuge simulation of the piloted launch of a manned multistage vehicle

    Science.gov (United States)

    Andrews, William H.; Holleman, Euclid C.

    1960-01-01

    An investigation was conducted to determine a human pilot's ability to control a multistage vehicle through the launch trajectory. The simulation was performed statically and dynamically by utilizing a human centrifuge. An interesting byproduct of the program was the three-axis side-located controller incorporated for pilot control inputs. This method of control proved to be acceptable for the successful completion of the tracking task during the simulation. There was no apparent effect of acceleration on the mechanical operation of the controller, but the pilot's control feel deteriorated as his dexterity decreased at high levels of acceleration. The application of control in a specific control mode was not difficult. However, coordination of more than one mode was difficult, and, in many instances, resulted in inadvertent control inputs. The acceptable control harmony at an acceleration level of 1 g became unacceptable at higher acceleration levels. Proper control-force harmony for a particular control task appears to be more critical for a three-axis controller than for conventional controllers. During simulations in which the pilot wore a pressure suit, the nature of the suit gloves further aggravated this condition.

  5. Three cases of radiation-induced cancer in oral regions

    International Nuclear Information System (INIS)

    Kawamura, Hiroshi; Shinoki, Kunihiko; Endo, Yoshitaka; Fujita, Yasushi; Hayashi, Susumu

    1985-01-01

    Three cases of radiation-induced cancer in the oral regions were reported with relation to radiation therapy. One was the general radiation-induced cancer following radiotherapy for the hemangioma. The other two cases, which belonged in the B-1 group of Sakai and his coworker's diagnostic criteria for radiation-induced cancer, were those occurring after radiotherapy for the malignant tumors. Due to the relatively high dosage exposure by the patient in the radiotherapy it is necessary to look out the latency of the radiation-induced cancer. After radiotherapy, careful and periodical observation is important for immediate treatment in an early stage for the radiation-induced cancer to have a favorable prognosis. In addition careful observation of the changes after radiotherapy helps in discovering the precancerous lesions from the therapy. For the radiation-induced cancer, surgical treatment would be the best, however, radiation therapy is also effective in certain cases. (author)

  6. Desertification and its effect on the erosion of vegetation in the south-western region of Saudi Arabia.

    Science.gov (United States)

    Abd El-Salam, Magda Magdy; Elhakem, Abeer Hamdy

    2016-03-01

    This study was conducted in Jazan region of south-western Saudi Arabia. Vegetation cover, frequency, abundance and soil characteristics were analysed at three locations with different quantitative and descriptive vegetation characteristics. Plant species were classified into three primary communities dominated by Salvadora persic, Acacia tortilis and Ziziphus spini-Christi. The results indicated that the distribution of plant species is controlled by soil characteristics. Very limited water resources are also limiting factor in vegetation growth. Among the three studied sites, desert and coastal environments are affected by desertification. Rehabilitation of the degraded lands requires collaborative efforts and support from the different related governmental sectors. Ecological conservation and sustainable development must be adopted as tools of rehabilitation.

  7. Vector control of three-phase AC/DC front-end converter

    Indian Academy of Sciences (India)

    Section 4 presents the simulation and experimental results of FEC. Section 5 discusses the problems associated with the starting process of ..... A 250-kVA vector-controlled FEC is simulated with MATLAB/SIMULINK. ..... Ghosh R 2007 Modelling, Analysis and Control of Single-phase and Three-phase PWM Rectifiers.

  8. Doping in controlling the type of conductivity in bulk and nanostructured thermoelectric materials

    International Nuclear Information System (INIS)

    Fuks, D.; Komisarchik, G.; Kaller, M.; Gelbstein, Y.

    2016-01-01

    Doping of materials for thermoelectric applications is widely used nowadays to control the type of conductivity. We report the results of ab-initio calculations aimed at developing the consistent scheme for determining the role of impurities that may change the type of conductivity in two attractive thermoelectric classes of materials. It is demonstrated that alloying of TiNiSn with Cu makes the material of n-type, and alloying with Fe leads to p-type conductivity. Similar calculations for PbTe with small amount of Na substituting for Pb leads to p-type conductivity, while Cl substituting for Te makes PbTe an n-type material. It is shown also that for nano-grained materials the n-type conductivity should be observed. The effect of impurities segregating to the grain boundaries in nano-structured PbTe is also discussed. - Highlights: • Bulk and nano-grained TE materials were analyzed by DFT. • The electronic effects on both PbTe and TiNiSn were demonstrated. • The role of impurities on the conductivity type was analyzed. • Interfacial states in nano-grained PbTe affect the conductivity type.

  9. A fuzzy controlled three-phase centrifuge for waste separation

    International Nuclear Information System (INIS)

    Parkinson, W.J.; Smith, R.E.; Miller, N.

    1998-02-01

    The three-phase centrifuge technology discussed in this paper was developed by Neal Miller, president of Centech, Inc. The three-phase centrifuge is an excellent device for cleaning up oil field and refinery wastes which are typically composed of hydrocarbons, water, and solids. The technology is unique. It turns the waste into salable oil, reusable water, and landfill-able solids. No secondary waste is produced. The problem is that only the inventor can set up and run the equipment well enough to provide an optimal cleanup. Demand for this device has far exceeded a one man operation. There is now a need for several centrifuges to be operated at different locations at the same time. This has produced a demand for an intelligent control system, one that could replace a highly skilled operator, or at least supplement the skills of a less experienced operator. The control problem is ideally suited to fuzzy logic, since the centrifuge is a highly complicated machine operated entirely by the skill and experience of the operator. A fuzzy control system was designed for and used with the centrifuge

  10. Control method of Three-phase Four-leg converter based on repetitive control

    Science.gov (United States)

    Hui, Wang

    2018-03-01

    The research chose the magnetic levitation force of wind power generation system as the object. In order to improve the power quality problem caused by unbalanced load in power supply system, we combined the characteristics and repetitive control principle of magnetic levitation wind power generation system, and then an independent control strategy for three-phase four-leg converter was proposed. In this paper, based on the symmetric component method, the second order generalized integrator was used to generate the positive and negative sequence of signals, and the decoupling control was carried out under the synchronous rotating reference frame, in which the positive and negative sequence voltage is PI double closed loop, and a PI regulator with repetitive control was introduced to eliminate the static error regarding the fundamental frequency fluctuation characteristic of zero sequence component. The simulation results based on Matlab/Simulink show that the proposed control project can effectively suppress the disturbance caused by unbalanced loads and maintain the load voltage balance. The project is easy to be achieved and remarkably improves the quality of the independent power supply system.

  11. Integrated Variable Speed Limits Control and Ramp Metering for Bottleneck Regions on Freeway

    Directory of Open Access Journals (Sweden)

    Ming-hui Ma

    2015-01-01

    Full Text Available To enhance the efficiency of the existing freeway system and therefore to mitigate traffic congestion and related problems on the freeway mainline lane-drop bottleneck region, the advanced strategy for bottleneck control is essential. This paper proposes a method that integrates variable speed limits and ramp metering for freeway bottleneck region control to relieve the chaos in bottleneck region. To this end, based on the analyses of spatial-temporal patterns of traffic flow, a macroscopic traffic flow model is extended to describe the traffic flow operating characteristic by considering the impacts of variable speed limits in mainstream bottleneck region. In addition, to achieve the goal of balancing the priority of the vehicles on mainline and on-ramp, increasing capacity, and reducing travel delay on bottleneck region, an improved control model, as well as an advanced control strategy that integrates variable speed limits and ramp metering, is developed. The proposed method is tested in simulation for a real freeway infrastructure feed and calibrates real traffic variables. The results demonstrate that the proposed method can substantially improve the traffic flow efficiency of mainline and on-ramp and enhance the quality of traffic flow at the investigated freeway mainline bottleneck.

  12. Cooperative monitoring of regional security agreements

    Energy Technology Data Exchange (ETDEWEB)

    Pregenzer, A.L.; Vannoni, M.; Biringer, K.L. [Sandia National Labs., Albuquerque, NM (United States). Nonproliferation and Arms Control Analysis Dept.

    1996-11-01

    This paper argues that cooperative monitoring plays a critical role in the implementation of regional security agreements and confidence building measures. A framework for developing cooperative monitoring options is proposed and several possibilities for relating bilateral and regional monitoring systems to international monitoring systems are discussed. Three bilateral or regional agreements are analyzed briefly to illustrate different possibilities. These examples illustrate that the relationship of regional or bilateral arms control or security agreements to international agreements depends on a number of factors: the overlap of provisions between regional and international agreements; the degree of interest in a regional agreement among the international community; efficiency in implementing the agreement; and numerous political considerations. Given the importance of regional security to the international community, regions should be encouraged to develop their own infrastructure for implementing regional arms control and other security agreements. A regional infrastructure need not preclude participation in an international regime. On the contrary, establishing regional institutions for arms control and nonproliferation could result in more proactive participation of regional parties in developing solutions for regional and international problems, thereby strengthening existing and future international regimes. Possible first steps for strengthening regional infrastructures are identified and potential technical requirements are discussed.

  13. Three-dimensional Monte Carlo simulations of W7-X plasma transport: density control and particle balance in steady-state operations

    International Nuclear Information System (INIS)

    Sharma, D.; Feng, Y.; Sardei, F.; Reiter, D.

    2005-01-01

    This paper presents self-consistent three-dimensional (3D) plasma transport simulations in the boundary of stellarator W7-X obtained with the Monte Carlo code EMC3-EIRENE for three typical island divertor configurations. The chosen 3D grid consists of relatively simple nested finite toroidal surfaces defined on a toroidal field period and covering the whole edge topology, which includes closed surfaces, islands and ergodic regions. Local grid refinements account for the required high resolution in the divertor region. The distribution of plasma density and temperature in the divertor region, as well as the power deposition profiles on the divertor plates, are shown to strongly depend on the island geometry, i.e. on the position and size of the dominant island chain. Configurations with strike-point positions closer to the gap of the divertor chamber generally favour the neutral compression in the divertor chamber and hence the pumping efficiency. The ratio of pumping to recycling fluxes is found to be roughly independent of the separatrix density and is thus a figure of merit for the quality of the configuration and of the divertor system in terms of density control. Lower limits for the achievable separatrix density, which determine the particle exhaust capabilities in stationary conditions, are compared for the three W7-X configurations

  14. On the height variation of the E-region cowling conductivity – effect of charged dust particles

    Directory of Open Access Journals (Sweden)

    P. Muralikrishna

    2006-11-01

    Full Text Available Height profiles of the Cowling conductivity in the electrojet region, estimated using the atmospheric parameters given by the existing models like CIRA or MSIS and measured electron density profiles, consistently show the heights of the electrojet current intensity peak to be more than 3 km below those estimated from in-situ measurements using magnetometers on board sounding rockets. Kulkarni and Muralikrishna (2005 attempted to explain this to be due to the effect of neutral dust particles. They reported that neutral dust particles, when they exist in sufficient numbers, can modify the collision parameters, especially in the lower E-region, where dust particles of meteoric origin are known to exist in large numbers, and thereby can modify the Cowling conductivity profile in the electrojet region. This work is extended here to include the effect of charged dust particles. Dust particles can become charged negatively by the attachment of ambient free electrons, and can thus reduce the number density of free electrons especially below the electrojet peak. This can alter the vertical profile of the east-west Hall current driven by the vertical Hall polarization field, thereby causing a net reduction in the electrojet current. Such a decrease in the electrojet current may be observed on the ground magnetograms. This mechanism, as proposed here, can operate only during periods of strong meteor shower activity, when the dust particle density at the assumed deposit height of 103 km can reach extreme values (for example, 5×104 cm−3 of 1-µm diameter dust particles. Such a dense dust layer may even cause a reversal in the normally upward vertical Hall polarization field, within the dust layer, causing a reversal of the electrojet currents below the current peak.

  15. Improved local and regional control with radiotherapy for Merkel cell carcinoma of the head and neck.

    Science.gov (United States)

    Strom, Tobin; Naghavi, Arash O; Messina, Jane L; Kim, Sungjune; Torres-Roca, Javier F; Russell, Jeffery; Sondak, Vernon K; Padhya, Tapan A; Trotti, Andy M; Caudell, Jimmy J; Harrison, Louis B

    2017-01-01

    We hypothesized that radiotherapy (RT) would improve both local and regional control with Merkel cell carcinoma of the head and neck. A single-institution institutional review board-approved study was performed including 113 patients with nonmetastatic Merkel cell carcinoma of the head and neck. Postoperative RT was delivered to the primary tumor bed (71.7% cases) ± draining lymphatics (33.3% RT cases). Postoperative local RT was associated with improved local control (3-year actuarial local control 89.4% vs 68.1%; p = .005; Cox hazard ratio [HR] 0.18; 95% confidence interval [CI] = 0.06-0.55; p = .002). Similarly, regional RT was associated with improved regional control (3-year actuarial regional control 95.0% vs 66.7%; p = .008; Cox HR = 0.09; 95% CI = 0.01-0.69; p = .02). Regional RT played an important role for both clinical node-negative patients (3-year regional control 100% vs 44.7%; p = .03) and clinical/pathological node-positive patients (3-year regional control 90.9% vs 55.6%; p = .047). Local RT was beneficial for all patients with Merkel cell carcinoma of the head and neck, whereas regional RT was beneficial for clinical node-negative and clinical/pathological node-positive patients. © 2016 Wiley Periodicals, Inc. Head Neck 39: 48-55, 2017. © 2016 Wiley Periodicals, Inc.

  16. NETWORK-CENTRIC TECHNOLOGIES FOR CONTROL OF THREE-PHASE NETWORK OPERATION MODES

    Directory of Open Access Journals (Sweden)

    Ye. I. Sokol

    2017-06-01

    Full Text Available Purpose. The development of the control system for three-phase network is based on intelligent technologies of network-centric control of heterogeneous objects. The introduction of unmanned aerial vehicles for monitoring of three-phase network increases the efficiency of management. Methodology. The case of decomposition of the instantaneous capacities of the fixed and variable components for 3-wire system. The features of power balance for the different modes of its functioning. It should be noted that symmetric sinusoidal mode is balanced and good, but really unbalanced, if the standard reactive power is not zero. To solve the problem of compensation is sufficient knowledge of the total value of the inactive components of full power (value of the inactive power without detail. The creation of a methodology of measurement and assessment will require knowledge of the magnitudes of each inactive component separately, which leads to the development of a unified approach to the measurement and compensation of inactive components of full power and the development of a generalized theory of power. Results. Procedure for the compensation of the current of zero sequence excludes from circuit the source, as the active component of instantaneous power of zero sequence, and a vector due to a current of zero sequence. This procedure is performed without time delay as it does not require integration. Only a 3–wire system with symmetrical voltage eliminates pulsations and symmetrization of the equivalent conductances of the phases of the task. Under asymmetric voltage, the power is different, its analysis requires the creation of a vector mathematical model of the energy processes of asymmetrical modes of 3–phase systems. Originality. The proposed method extends the basis of the vector method for any zero sequence voltages and shows that the various theories of instantaneous power three wired scheme due to the choice of a basis in a two

  17. COORDINATION IN MULTILEVEL NETWORK-CENTRIC CONTROL SYSTEMS OF REGIONAL SECURITY: APPROACH AND FORMAL MODEL

    Directory of Open Access Journals (Sweden)

    A. V. Masloboev

    2015-01-01

    Full Text Available The paper deals with development of methods and tools for mathematical and computer modeling of the multilevel network-centric control systems of regional security. This research is carried out under development strategy implementation of the Arctic zone of the Russian Federation and national safeguarding for the period before 2020 in the Murmansk region territory. Creation of unified interdepartmental multilevel computer-aided system is proposed intended for decision-making information support and socio-economic security monitoring of the Arctic regions of Russia. The distinctive features of the investigated system class are openness, self-organization, decentralization of management functions and decision-making, weak hierarchy in the decision-making circuit and goal generation capability inside itself. Research techniques include functional-target approach, mathematical apparatus of multilevel hierarchical system theory and principles of network-centric control of distributed systems with pro-active components and variable structure. The work considers network-centric management local decisions coordination problem-solving within the multilevel distributed systems intended for information support of regional security. The coordination problem-solving approach and problem formalization in the multilevel network-centric control systems of regional security have been proposed based on developed multilevel recurrent hierarchical model of regional socio-economic system complex security. The model provides coordination of regional security indexes, optimized by the different elements of multilevel control systems, subject to decentralized decision-making. The model specificity consists in application of functional-target technology and mathematical apparatus of multilevel hierarchical system theory for coordination procedures implementation of the network-centric management local decisions. The work-out and research results can find further

  18. Application of the finite element groundwater model FEWA to three regional aquifers

    International Nuclear Information System (INIS)

    Wong, K.F.V.; Yeh, G.T.

    1986-06-01

    This report documents the calibration with field data and predictive application of a finite element model of water through aquifers (FEWA). FEWA was described in a report written by G.T. Yeh and D.D. Huff in 1983. The model was first compared with the United States Geological Survey (USGS) two-dimensional model and found superior in treating anisotropic media when the coordinates cannot be made to coincide with the principal directions of hydraulic conductivities. In addition, there was no necessity to define nodal points outside the region, as required by the USGS model. FEWA was next calibrated with measured potentiometric surfaces from the Love Canal area in New York and the Conesville area in Ohio. There were satisfactory matches between computed results and available field data. The calibration and predictive runs of FEWA were then accomplished with the Hialeah-Preston well field data over the Biscayne aquifer in south Florida. The calibration run yielded two values of hydraulic conductivity in the area, and the predictive run gave results that matched well with available data. 18 refs., 28 figs

  19. Application of the finite element groundwater model FEWA to three regional aquifers

    Energy Technology Data Exchange (ETDEWEB)

    Wong, K.F.V.; Yeh, G.T.

    1986-06-01

    This report documents the calibration with field data and predictive application of a finite element model of water through aquifers (FEWA). FEWA was described in a report written by G.T. Yeh and D.D. Huff in 1983. The model was first compared with the United States Geological Survey (USGS) two-dimensional model and found superior in treating anisotropic media when the coordinates cannot be made to coincide with the principal directions of hydraulic conductivities. In addition, there was no necessity to define nodal points outside the region, as required by the USGS model. FEWA was next calibrated with measured potentiometric surfaces from the Love Canal area in New York and the Conesville area in Ohio. There were satisfactory matches between computed results and available field data. The calibration and predictive runs of FEWA were then accomplished with the Hialeah-Preston well field data over the Biscayne aquifer in south Florida. The calibration run yielded two values of hydraulic conductivity in the area, and the predictive run gave results that matched well with available data. 18 refs., 28 figs.

  20. Financial considerations in the conduct of multi-centre randomised controlled trials: evidence from a qualitative study

    Directory of Open Access Journals (Sweden)

    Grant Adrian M

    2006-12-01

    Full Text Available Abstract Background Securing and managing finances for multicentre randomised controlled trials is a highly complex activity which is rarely considered in the research literature. This paper describes the process of financial negotiation and the impact of financial considerations in four UK multicentre trials. These trials had met, or were on schedule to meet, recruitment targets agreed with their public-sector funders. The trials were considered within a larger study examining factors which might be associated with trial recruitment (STEPS. Methods In-depth semi-structured telephone interviews were conducted in 2003–04 with 45 individuals with various responsibilities to one of the four trials. Interviewees were recruited through purposive and then snowball sampling. Interview transcripts were analysed with the assistance of the qualitative package Atlas-ti. Results The data suggest that the UK system of dividing funds into research, treatment and NHS support costs brought the trial teams into complicated negotiations with multiple funders. The divisions were somewhat malleable and the funding system was used differently in each trial. The fact that all funders had the potential to influence and shape the trials considered here was an important issue as the perspectives of applicants and funders could diverge. The extent and range of industry involvement in non-industry-led trials was striking. Three broad periods of financial work (foundation, maintenance, and resourcing completion were identified. From development to completion of a trial, the trialists had to be resourceful and flexible, adapting to changing internal and external circumstances. In each period, trialists and collaborators could face changing costs and challenges. Each trial extended the recruitment period; three required funding extensions from MRC or HTA. Conclusion This study highlights complex financial aspects of planning and conducting trials, especially where multiple