WorldWideScience

Sample records for thinning acceptance criteria

  1. Hanford Site solid waste acceptance criteria

    International Nuclear Information System (INIS)

    Ellefson, M.D.

    1998-01-01

    Order 5820.2A requires that each treatment, storage, and/or disposal facility (referred to in this document as TSD unit) that manages low-level or transuranic waste (including mixed waste and TSCA PCB waste) maintain waste acceptance criteria. These criteria must address the various requirements to operate the TSD unit in compliance with applicable safety and environmental requirements. This document sets forth the baseline criteria for acceptance of radioactive waste at TSD units operated by WMH. The criteria for each TSD unit have been established to ensure that waste accepted can be managed in a manner that is within the operating requirements of the unit, including environmental regulations, DOE Orders, permits, technical safety requirements, waste analysis plans, performance assessments, and other applicable requirements. Acceptance criteria apply to the following TSD units: the Low-Level Burial Grounds (LLBG) including both the nonregulated portions of the LLBG and trenches 31 and 34 of the 218-W-5 Burial Ground for mixed waste disposal; Central Waste Complex (CWC); Waste Receiving and Processing Facility (WRAP); and T Plant Complex. Waste from all generators, both from the Hanford Site and from offsite facilities, must comply with these criteria. Exceptions can be granted as provided in Section 1.6. Specific waste streams could have additional requirements based on the 1901 identified TSD pathway. These requirements are communicated in the Waste Specification Records (WSRds). The Hanford Site manages nonradioactive waste through direct shipments to offsite contractors. The waste acceptance requirements of the offsite TSD facility must be met for these nonradioactive wastes. This document does not address the acceptance requirements of these offsite facilities

  2. Hanford Site Solid Waste Acceptance Criteria

    Energy Technology Data Exchange (ETDEWEB)

    1993-11-17

    This manual defines the Hanford Site radioactive, hazardous, and sanitary solid waste acceptance criteria. Criteria in the manual represent a guide for meeting state and federal regulations; DOE Orders; Hanford Site requirements; and other rules, regulations, guidelines, and standards as they apply to acceptance of radioactive and hazardous solid waste at the Hanford Site. It is not the intent of this manual to be all inclusive of the regulations; rather, it is intended that the manual provide the waste generator with only the requirements that waste must meet in order to be accepted at Hanford Site TSD facilities.

  3. Hanford Site Solid Waste Acceptance Criteria

    International Nuclear Information System (INIS)

    1993-01-01

    This manual defines the Hanford Site radioactive, hazardous, and sanitary solid waste acceptance criteria. Criteria in the manual represent a guide for meeting state and federal regulations; DOE Orders; Hanford Site requirements; and other rules, regulations, guidelines, and standards as they apply to acceptance of radioactive and hazardous solid waste at the Hanford Site. It is not the intent of this manual to be all inclusive of the regulations; rather, it is intended that the manual provide the waste generator with only the requirements that waste must meet in order to be accepted at Hanford Site TSD facilities

  4. NEVADA TEST SITE WASTE ACCEPTANCE CRITERIA

    International Nuclear Information System (INIS)

    U.S. DEPARTMENT OF ENERGY, NATIONAL NUCLEAR SECURITY ADMINISTRATION, NEVADA SITE OFFICE

    2005-01-01

    This document establishes the U. S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO) waste acceptance criteria (WAC). The WAC provides the requirements, terms, and conditions under which the Nevada Test Site will accept low-level radioactive and mixed waste for disposal. Mixed waste generated within the State of Nevada by NNSA/NSO activities is accepted for disposal. It includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the Nevada Test Site Area 3 and Area 5 Radioactive Waste Management Site for storage or disposal

  5. Nevada Test Site Waste Acceptance Criteria, December 2000

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-12-01

    This document establishes the US Department of Energy, Nevada Operations Office waste acceptance criteria. The waste acceptance criteria provides the requirements, terms, and conditions under which the Nevada Test Site will accept low-level radioactive waste and mixed waste for disposal. It includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the Nevada Test Site Area 3 and Area 5 Radioactive Waste Management Sites for storage or disposal.

  6. Nevada Test Site Waste Acceptance Criteria, December 2000

    International Nuclear Information System (INIS)

    2000-01-01

    This document establishes the US Department of Energy, Nevada Operations Office waste acceptance criteria. The waste acceptance criteria provides the requirements, terms, and conditions under which the Nevada Test Site will accept low-level radioactive waste and mixed waste for disposal. It includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the Nevada Test Site Area 3 and Area 5 Radioactive Waste Management Sites for storage or disposal

  7. Idaho CERCLA Disposal Facility Complex Waste Acceptance Criteria

    Energy Technology Data Exchange (ETDEWEB)

    W. Mahlon Heileson

    2006-10-01

    The Idaho Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) Disposal Facility (ICDF) has been designed to accept CERCLA waste generated within the Idaho National Laboratory. Hazardous, mixed, low-level, and Toxic Substance Control Act waste will be accepted for disposal at the ICDF. The purpose of this document is to provide criteria for the quantities of radioactive and/or hazardous constituents allowable in waste streams designated for disposal at ICDF. This ICDF Complex Waste Acceptance Criteria is divided into four section: (1) ICDF Complex; (2) Landfill; (3) Evaporation Pond: and (4) Staging, Storage, Sizing, and Treatment Facility (SSSTF). The ICDF Complex section contains the compliance details, which are the same for all areas of the ICDF. Corresponding sections contain details specific to the landfill, evaporation pond, and the SSSTF. This document specifies chemical and radiological constituent acceptance criteria for waste that will be disposed of at ICDF. Compliance with the requirements of this document ensures protection of human health and the environment, including the Snake River Plain Aquifer. Waste placed in the ICDF landfill and evaporation pond must not cause groundwater in the Snake River Plain Aquifer to exceed maximum contaminant levels, a hazard index of 1, or 10-4 cumulative risk levels. The defined waste acceptance criteria concentrations are compared to the design inventory concentrations. The purpose of this comparison is to show that there is an acceptable uncertainty margin based on the actual constituent concentrations anticipated for disposal at the ICDF. Implementation of this Waste Acceptance Criteria document will ensure compliance with the Final Report of Decision for the Idaho Nuclear Technology and Engineering Center, Operable Unit 3-13. For waste to be received, it must meet the waste acceptance criteria for the specific disposal/treatment unit (on-Site or off-Site) for which it is destined.

  8. Risk acceptance criteria of the Nuclear Regulatory Authority

    International Nuclear Information System (INIS)

    Felizia, Eduardo R.

    2005-01-01

    This report describes some of the regulatory and control functions legally conferred upon the Argentine Nuclear Regulatory Authority concerning radiological risks, as well as a critical analysis of the radiological risk acceptance criteria contained in the Argentine regulatory system. A summary of the application of regulatory standards AR 3.1.3. - 'Radiological criteria related to accidents in nuclear power reactors' and AR 4.1.3. - 'Radiological criteria related to accidents in research reactors' to concrete cases is made, while the favourable and unfavourable aspects of the risk acceptance criteria are discussed. The conclusion is that the Argentine regulatory system contains adequate radiological risk acceptance criteria, that the latter are consistent with the radiological protection principles applicable to man and that, for the moment, there is no need to perform any modifications that would broaden the conceptual framework on which such criteria are based. (author) [es

  9. Nevada Test Site Waste Acceptance Criteria

    International Nuclear Information System (INIS)

    U. S. Department of Energy, National Nuclear Security Administration Nevada Site Office

    2005-01-01

    This document establishes the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO) waste acceptance criteria (WAC). The WAC provides the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive (LLW) and mixed waste (MW) for disposal. It includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NTS Area 3 and Area 5 Radioactive Waste Management Complex (RWMC) for storage or disposal

  10. Inelastic analysis acceptance criteria for radioactive material transportation containers

    International Nuclear Information System (INIS)

    Ammerman, D.J.; Ludwigsen, J.S.

    1993-01-01

    The design criteria currently used in the design of radioactive material (RAM) transportation containers are taken from the ASME Boiler and Pressure Vessel Code (ASME, 1992). These load-based criteria are ideally suited for pressure vessels where the loading is quasistatic and all stresses are in equilibrium with externally applied loads. For impact events, the use of load-based criteria is less supportable. Impact events tend to be energy controlled, and thus, energy-based acceptance criteria would appear to be more appropriate. Determination of an ideal design criteria depends on what behavior is desired. Currently there is not a design criteria for inelastic analysis for RAM nation packages that is accepted by the regulatory agencies. This lack of acceptance criteria is one of the major factors in limiting the use of inelastic analysis. In this paper inelastic analysis acceptance criteria based on stress and strain-energy density will be compared for two stainless steel test units subjected to impacts onto an unyielding target. Two different material models are considered for the inelastic analysis, a bilinear fit of the stress-strain curve and a power law hardening model that very closely follows the stress-strain curve. It is the purpose of this paper to stimulate discussion and research into the area of strain-energy density based inelastic analysis acceptance criteria

  11. Reality check on girth weld defect acceptance criteria

    Energy Technology Data Exchange (ETDEWEB)

    Brust, Bud; Kalyanam, Suresh; Shim, Do-Jun; Wilkowski, Gery [Engineering Mechanics Corporation of Columbus, Columbus, OH, (United States)

    2010-07-01

    Girth weld defect tolerance criteria for pipeline construction has evolved with time. Recently, ERPG recommended a new Tier 2 girth weld defect acceptance criterion. This paper described the new development on girth weld defect acceptance criteria. The inherent conservatisms of alternative girth weld defect acceptance criteria from the 2007 API 1104 Appendix A, CSA Z662 Appendix K, are compared to those from the proposed EPRG Tier 2 criteria. It is found that the API and CSA codes have the same empirical limit-load criteria. As well, there are conservatisms in the proposed EPRG Tier 2. The results showed that there are various reasons why large amounts of conservatism in the allowable flaw lengths in the CSA Appendix K,2007 API 1104 Appendix A, and proposed EPRG Tier 2 girth weld defect criterion exist. Small conservatisms on failure stress can result in large conservatisms in flaw size.

  12. Risk Acceptance Criteria and/or Decision optimization

    DEFF Research Database (Denmark)

    Ditlevsen, Ove Dalager

    1996-01-01

    Acceptance criteria applied in practical risk analysis are recapitulated including the concept of rist profile. Modelling of risk profiles is illustrated on the basis of compound Poisson process models. The current practice of authoritative acceptance criteria formulation is discussed from...... a decision theoretical point of view. It is argued that the phenomenon of risk aversion rather than being of concern to the authority should be of concern to the owner. Finally it is discussed whether there is an ethical problem when formally capitalising human lives with a positive interest rate. Keywords......: Risk acceptance, Risk profile, Compound Poisson model for risk profile, Capitalization of human life, Risk aversion....

  13. Design Criteria for Achieving Acceptable Indoor Radon Concentration

    DEFF Research Database (Denmark)

    Rasmussen, Torben Valdbjørn

    2016-01-01

    Design criteria for achieving an acceptable indoor radon concentration are presented in this paper. The paper suggests three design criteria. These criteria have to be considered at the early stage of the building design phase to meet the latest recommendations from the World Health Organization...... in most countries. The three design criteria are; first, establishing a radon barrier facing the ground; second, lowering the air pressure in the lower zone of the slab on ground facing downwards; third, diluting the indoor air with outdoor air. The first two criteria can prevent radon from infiltrating...... from the ground, and the third criteria can dilute the indoor air. By combining these three criteria, the indoor radon concentration can be lowered achieving an acceptable level. In addition, a cheap and reliable method for measuring the radon concentration in the indoor air is described. The provision...

  14. Radwaste characteristics and Disposal Facility Waste Acceptance Criteria

    International Nuclear Information System (INIS)

    Sung, Suk Hyun; Jeong, Yi Yeong; Kim, Ki Hong

    2008-01-01

    The purpose of Radioactive Waste Acceptance Criteria (WAC) is to verify a radioactive waste compliance with radioactive disposal facility requirements in order to maintain a disposal facility's performance objectives and to ensure its safety. To develop WAC which is conformable with domestic disposal site conditions, we furthermore analysed the WAC of foreign disposal sites similar to the Kyung-Ju disposal site and the characteristics of various wastes which are being generated from Korea nuclear facilities. Radioactive WAC was developed in the technical cooperation with the Korea Atomic Energy Research Institute in consideration of characteristics of the wastes which are being generated from various facilities, waste generators' opinions and other conditions. The established criteria was also discussed and verified at an advisory committee which was comprised of some experts from universities, institutes and the industry. So radioactive WAC was developed to accept all wastes which are being generated from various nuclear facilities as much as possible, ensuring the safety of a disposal facility. But this developed waste acceptance criteria is not a criteria to accept all the present wastes generated from various nuclear facilities, so waste generators must seek an alternative treatment method for wastes which were not worth disposing of, and then they must treat the wastes more to be acceptable at a disposal site. The radioactive disposal facility WAC will continuously complement certain criteria related to a disposal concentration limit for individual radionuclide in order to ensure a long-term safety.

  15. Structural acceptance criteria Remote Handling Building Tritium Extraction Facility

    Energy Technology Data Exchange (ETDEWEB)

    Mertz, G.

    1999-12-16

    This structural acceptance criteria contains the requirements for the structural analysis and design of the Remote Handling Building (RHB) in the Tritium Extraction Facility (TEF). The purpose of this acceptance criteria is to identify the specific criteria and methods that will ensure a structurally robust building that will safely perform its intended function and comply with the applicable Department of Energy (DOE) structural requirements.

  16. Structural acceptance criteria Remote Handling Building Tritium Extraction Facility

    International Nuclear Information System (INIS)

    Mertz, G.

    1999-01-01

    This structural acceptance criteria contains the requirements for the structural analysis and design of the Remote Handling Building (RHB) in the Tritium Extraction Facility (TEF). The purpose of this acceptance criteria is to identify the specific criteria and methods that will ensure a structurally robust building that will safely perform its intended function and comply with the applicable Department of Energy (DOE) structural requirements

  17. Nevada National Security Site Waste Acceptance Criteria

    International Nuclear Information System (INIS)

    2012-01-01

    This document establishes the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO), Nevada National Security Site Waste Acceptance Criteria (NNSSWAC). The NNSSWAC provides the requirements, terms, and conditions under which the Nevada National Security Site (NNSS) will accept DOE non-radioactive classified waste, DOE non-radioactive hazardous classified waste, DOE low-level radioactive waste (LLW), DOE mixed low-level waste (MLLW), and U.S. Department of Defense (DOD) classified waste for permanent disposal. Classified waste is the only waste accepted for disposal that may be non-radioactive and will be required to meet the waste acceptance criteria for radioactive waste as specified in this document. The NNSA/NSO and support contractors are available to assist you in understanding or interpreting this document. For assistance, please call the NNSA/NSO Waste Management Project (WMP) at (702) 295-7063, and your call will be directed to the appropriate contact.

  18. Nevada National Security Site Waste Acceptance Criteria

    Energy Technology Data Exchange (ETDEWEB)

    NSTec Environmental Management

    2012-02-28

    This document establishes the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO), Nevada National Security Site Waste Acceptance Criteria (NNSSWAC). The NNSSWAC provides the requirements, terms, and conditions under which the Nevada National Security Site (NNSS) will accept DOE non-radioactive classified waste, DOE non-radioactive hazardous classified waste, DOE low-level radioactive waste (LLW), DOE mixed low-level waste (MLLW), and U.S. Department of Defense (DOD) classified waste for permanent disposal. Classified waste is the only waste accepted for disposal that may be non-radioactive and will be required to meet the waste acceptance criteria for radioactive waste as specified in this document. The NNSA/NSO and support contractors are available to assist you in understanding or interpreting this document. For assistance, please call the NNSA/NSO Waste Management Project (WMP) at (702) 295-7063, and your call will be directed to the appropriate contact.

  19. Waste-acceptance criteria for greater confinement disposal

    International Nuclear Information System (INIS)

    Gilbert, T.L.; Meshkov, N.K.

    1987-01-01

    A methodology for establishing waste-acceptance criteria based on quantitative performance factors that characterize the confinement capabilities of a waste disposal site and facility has been developed. The methodology starts from the basic objective of protecting public health and safety by providing assurance that disposal of the waste will not result in a radiation dose to any member of the general public, in either the short or long term, in excess of an established basic dose limit. The method is based on an explicit, straight-forward, and quantitative relationship among individual risk, confinement capabilities, and waste characteristics. A key aspect of the methodology is introduction of a confinement factor that characterizes the overall confinement capability of a particular facility and can be used for quantitative assessments of the performance of different disposal sites and facilities, as well as for establishing site-specific waste acceptance criteria. Confinement factors are derived by means of site-specific pathway analyses. They make possible a direct and simple conversion of a basic dose limit into waste-acceptance criteria, specified as concentration limits on radionuclides in the waste streams and expressed in quantitative form as a function of parameters that characterize the site, facility design, waste containers, and waste form. Waste acceptance criteria can be represented visually as activity/time plots for various waste streams. These plots show the concentrations of radionuclides in a waste stream as a function of time and permit a visual, quantitative assessment of long-term performance, relative risks from different radionuclides in the waste stream, and contributions from ingrowth. 13 references, 7 figures

  20. Waste-acceptance criteria for greater-confinement disposal

    International Nuclear Information System (INIS)

    Gilbert, T.L.; Meshkov, N.K.

    1986-01-01

    A methodology for establishing waste-acceptance criteria based on quantitative performance factors that characterize the confinement capabilities of a waste-disposal site and facility has been developed. The methodology starts from the basic objective of protecting public health and safety by providing assurance that dispsoal of the waste will not result in a radiation dose to any member of the general public, in either the short or long term, in excess of an established basic dose limit. The method is based on an explicit, straightforward, and quantitative relationship among individual risk, confinement capabilities, and waste characteristics. A key aspect of the methodology is the introduction of a confinement factor that characterizes the overall confinement capability of a particular facility and can be used for quantitative assessments of the performance of different disposal sites and facilities, as well as for establishing site-specific waste-acceptance criteria. Confinement factors are derived by means of site-specific pathway analyses. They make possible a direct and simple conversion of a basic dose limit into waste-acceptance criteria, specified as concentration limits on radionuclides in the waste streams and expressed in quantitative form as a function of parameters that characterize the site, facility design, waste containers, and waste form. Waste-acceptance criteria can be represented visually as activity/time plots for various waste streams. These plots show the concentrations of radionuclides in a waste stream as a function of time and permit a visual, quantitative assessment of long-term performance, relative risks from different radionuclides in the waste stream, and contributions from ingrowth. 13 refs

  1. Nevada Test Site Waste Acceptance Criteria (NTSWAC)

    Energy Technology Data Exchange (ETDEWEB)

    NNSA/NSO Waste Management Project

    2008-06-01

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office, Nevada Test Site Waste Acceptance Criteria (NTSWAC). The NTSWAC provides the requirements, terms, and conditions under which the Nevada Test Site will accept low-level radioactive (LLW) and LLW Mixed Waste (MW) for disposal.

  2. Nevada Test Site Waste Acceptance Criteria (NTSWAC)

    International Nuclear Information System (INIS)

    NNSA/NSO Waste Management Project

    2008-01-01

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office, Nevada Test Site Waste Acceptance Criteria (NTSWAC). The NTSWAC provides the requirements, terms, and conditions under which the Nevada Test Site will accept low-level radioactive (LLW) and LLW Mixed Waste (MW) for disposal

  3. Toxic chemical risk acceptance criteria

    International Nuclear Information System (INIS)

    Craig, D.K.; Davis, J.; Lee, L.; Lein, P.; Omberg, S.

    1992-01-01

    This paper presents recommendations of a subcommittee of the Westinghouse M ampersand 0 Nuclear Facility Safety Committee concerning toxic chemical risk acceptance criteria. Two sets of criteria have been developed, one for use in the hazard classification of facilities, and the second for use in comparing risks in DOE non-reactor nuclear facility Safety Analysis Reports. The Emergency Response Planning Guideline (ERPG) values are intended to provide estimates of concentration ranges for specific chemicals above which exposure would be expected to lead to adverse heath effects of increasing severity for ERPG-1, -2, and -3s. The subcommittee recommends that criteria for hazard class or risk range be based on ERPGs for all chemicals. Probability-based Incremental Cancer Risk (ICR) criteria are recommended for additional analyses of risks from all known or suspected human carcinogens. Criteria are given for both on-site and off-site exposure. The subcommittee also recommends that the 5-minute peak concentration be compared with the relevant criterion with no adjustment for exposure time. Since ERPGs are available for only a limited number of chemicals, the subcommittee has developed a proposed hierarchy of concentration limit parameters for the different criteria

  4. Application of trial risk acceptance criteria

    International Nuclear Information System (INIS)

    Johnson, D.H.; Kastenberg, W.E.; Okrent, D.

    1982-01-01

    The objective of this paper is to investigate some of the implications inherent in the application of various proposed sets of risk acceptance criteria. A power-law model of risk aversion is utilized to estimate the equivalent number of individual deaths and is treated parametrically. The implications of ALARA requirements for cost-effective improvements are also illustrated. The risks assessed for various technological endeavors, as well as some estimated natural background risks, are compared to the trial criteria

  5. Environmental Restoration Disposal Facility Waste Acceptance Criteria

    International Nuclear Information System (INIS)

    Dronen, V.R.

    1998-06-01

    The Hanford Site is operated by the U. S. Department of Energy (DOE) with a primary mission of environmental cleanup and restoration. The Environmental Restoration Disposal Facility (ERDF) is an integral part of the DOE environmental restoration effort at the Hanford Site. The purpose of this document is to establish the ERDF waste acceptance criteria for disposal of materials resulting from Hanford Site cleanup activities. Definition of and compliance with the requirements of this document will enable implementation of appropriate measures to protect human health and the environment, ensure the integrity of the ERDF liner system, facilitate efficient use of the available space in the ERDF, and comply with applicable environmental regulations and DOE orders. To serve this purpose, the document defines responsibilities, identifies the waste acceptance process, and provides the primary acceptance criteria and regulatory citations to guide ERDF users. The information contained in this document is not intended to repeat or summarize the contents of all applicable regulations

  6. Nevada National Security Site Waste Acceptance Criteria

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2013-06-01

    This document establishes the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Field Office (NNSA/NFO), Nevada National Security Site Waste Acceptance Criteria (NNSSWAC). The NNSSWAC provides the requirements, terms, and conditions under which the Nevada National Security Site (NNSS) will accept the following: • DOE hazardous and non-hazardous non-radioactive classified waste • DOE low-level radioactive waste (LLW) • DOE mixed low-level waste (MLLW) • U.S. Department of Defense (DOD) classified waste The LLW and MLLW listed above may also be classified waste. Classified waste is the only waste accepted for disposal that may be non-radioactive and shall be required to meet the waste acceptance criteria for radioactive waste as specified in this document. Classified waste may be sent to the NNSS as classified matter. Section 3.1.18 provides the requirements that must be met for permanent burial of classified matter. The NNSA/NFO and support contractors are available to assist the generator in understanding or interpreting this document. For assistance, please call the NNSA/NFO Environmental Management Operations (EMO) at (702) 295-7063, and the call will be directed to the appropriate contact.

  7. Nevada National Security Site Waste Acceptance Criteria

    International Nuclear Information System (INIS)

    2013-01-01

    This document establishes the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Field Office (NNSA/NFO), Nevada National Security Site Waste Acceptance Criteria (NNSSWAC). The NNSSWAC provides the requirements, terms, and conditions under which the Nevada National Security Site (NNSS) will accept the following: DOE hazardous and non-hazardous non-radioactive classified waste; DOE low-level radioactive waste (LLW); DOE mixed low-level waste (MLLW); and, U.S. Department of Defense (DOD) classified waste. The LLW and MLLW listed above may also be classified waste. Classified waste is the only waste accepted for disposal that may be non-radioactive and shall be required to meet the waste acceptance criteria for radioactive waste as specified in this document. Classified waste may be sent to the NNSS as classified matter. Section 3.1.18 provides the requirements that must be met for permanent burial of classified matter. The NNSA/NFO and support contractors are available to assist the generator in understanding or interpreting this document. For assistance, please call the NNSA/NFO Environmental Management Operations (EMO) at (702) 295-7063, and the call will be directed to the appropriate contact.

  8. Automated Transportation Management System (ATMS) V2.0 logistics module PBI acceptance criteria

    International Nuclear Information System (INIS)

    Weidert, R.S.

    1995-01-01

    This document defines the acceptance criteria for the Automated Transportation Management System V2.0 Logistics Module Performance Based Incentive (PBI). This acceptance criteria will be the primary basis for the generation of acceptance test procedures. The purpose of this document is to define the minimum criteria that must be fulfilled to guarantee acceptance of the Logistics Module

  9. Acceptance criteria for the evaluation of nuclear power reactor security plans

    International Nuclear Information System (INIS)

    1982-08-01

    This guidance document contains acceptance criteria to be used in the NRC license review process. It contains specific criteria for use in evaluating the acceptability of nuclear power reactor security programs as detailed in security plans

  10. Human factors engineering design review acceptance criteria for the safety parameter display

    International Nuclear Information System (INIS)

    McGevna, V.; Peterson, L.R.

    1981-01-01

    This report contains human factors engineering design review acceptance criteria developed by the Human Factors Engineering Branch (HFEB) of the Nuclear Regulatory Commission (NRC) to use in evaluating designs of the Safety Parameter Display System (SPDS). These criteria were developed in response to the functional design criteria for the SPDS defined in NUREG-0696, Functional Criteria for Emergency Response Facilities. The purpose of this report is to identify design review acceptance criteria for the SPDS installed in the control room of a nuclear power plant. Use of computer driven cathode ray tube (CRT) displays is anticipated. General acceptance criteria for displays of plant safety status information by the SPDS are developed. In addition, specific SPDS review criteria corresponding to the SPDS functional criteria specified in NUREG-0696 are established

  11. Anticipating Potential Waste Acceptance Criteria for Defense Spent Nuclear Fuel

    International Nuclear Information System (INIS)

    Rechard, R.P.; Lord, M.E.; Stockman, C.T.; McCurley, R.D.

    1997-01-01

    The Office of Environmental Management of the U.S. Department of Energy is responsible for the safe management and disposal of DOE owned defense spent nuclear fuel and high level waste (DSNF/DHLW). A desirable option, direct disposal of the waste in the potential repository at Yucca Mountain, depends on the final waste acceptance criteria, which will be set by DOE's Office of Civilian Radioactive Waste Management (OCRWM). However, evolving regulations make it difficult to determine what the final acceptance criteria will be. A method of anticipating waste acceptance criteria is to gain an understanding of the DOE owned waste types and their behavior in a disposal system through a performance assessment and contrast such behavior with characteristics of commercial spent fuel. Preliminary results from such an analysis indicate that releases of 99Tc and 237Np from commercial spent fuel exceed those of the DSNF/DHLW; thus, if commercial spent fuel can meet the waste acceptance criteria, then DSNF can also meet the criteria. In large part, these results are caused by the small percentage of total activity of the DSNF in the repository (1.5%) and regulatory mass (4%), and also because commercial fuel cladding was assumed to provide no protection

  12. Nevada National Security Site Waste Acceptance Criteria

    Energy Technology Data Exchange (ETDEWEB)

    NSTec Environmental Management

    2010-09-03

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO) Nevada National Security Site Waste Acceptance Criteria (NNSSWAC). The NNSSWAC provides the requirements, terms, and conditions under which the Nevada National Security Site (NNSS) will accept low-level radioactive waste and mixed low-level waste for disposal. The NNSSWAC includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NNSS Area 3 and Area 5 Radioactive Waste Management Complex for disposal. The NNSA/NSO and support contractors are available to assist you in understanding or interpreting this document. For assistance, please call the NNSA/NSO Waste Management Project at (702) 295-7063 or fax to (702) 295-1153.

  13. Nevada National Security Site Waste Acceptance Criteria

    International Nuclear Information System (INIS)

    2010-01-01

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO) Nevada National Security Site Waste Acceptance Criteria (NNSSWAC). The NNSSWAC provides the requirements, terms, and conditions under which the Nevada National Security Site (NNSS) will accept low-level radioactive waste and mixed low-level waste for disposal. The NNSSWAC includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NNSS Area 3 and Area 5 Radioactive Waste Management Complex for disposal. The NNSA/NSO and support contractors are available to assist you in understanding or interpreting this document. For assistance, please call the NNSA/NSO Waste Management Project at (702) 295-7063 or fax to (702) 295-1153.

  14. Nevada National Security Site Waste Acceptance Criteria

    International Nuclear Information System (INIS)

    2011-01-01

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO) Nevada National Security Site Waste Acceptance Criteria (NNSSWAC). The NNSSWAC provides the requirements, terms, and conditions under which the Nevada National Security Site (NNSS) will accept low-level radioactive waste and mixed low-level waste for disposal. The NNSSWAC includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NNSS Area 3 and Area 5 Radioactive Waste Management Complex for disposal. The NNSA/NSO and support contractors are available to assist you in understanding or interpreting this document. For assistance, please call the NNSA/NSO Waste Management Project at (702) 295-7063 or fax to (702) 295-1153.

  15. A Study on the Acceptance Criteria for DTrip Frequency

    International Nuclear Information System (INIS)

    Kim, Kil Yoo; Lee, Hyun Woo; Jae, Moo Sung

    2011-01-01

    Many risk informed regulation and applications (RIR and A) are approved, and more RIR and A will be actively applied in Korea. The acceptance criteria for the RIR and A have been DCDF, and DLERF. However, in the economical point of view, the change of the reactor trip frequency (hereafter, it is called Dtrip) are important element to monitor in the RIR and A. A reactor trip causes a huge economical loss, and causes a bad reputation in the social acceptance which causes eventually a social cost, and could induce a safety problem by giving a severe stress on the operators. Usually, the chief managers of nuclear power plants are reluctant to increase the trip frequency by a RIR and A, even though the RIR and A could bring an economical benefit, and could not threaten the safety. Because, if a reactor trip occurs, it would be reflected in his performance assessment. Therefore, it is necessary to set up an acceptance criteria for Dtrip in the RIR and A without depending on the personal preference of the chief manager. This paper introduces the acceptance criteria for Dtrip in the RIR and A

  16. Acceptance criteria for radioactive waste deposition

    International Nuclear Information System (INIS)

    Rzyski, B.M.

    1989-01-01

    The disposal of low-and intermediate level radioactive waste in either shallow ground or rock cavities must be subjected to special guidelines which are used by national authorities and implementing bodies when establishing and regulating respositories. These informations are given by the acceptance criteria and will depend on specific site conditions and optmized procedures. (author) [pt

  17. DISPOSABLE CANISTER WASTE ACCEPTANCE CRITERIA

    Energy Technology Data Exchange (ETDEWEB)

    R.J. Garrett

    2001-07-30

    The purpose of this calculation is to provide the bases for defining the preclosure limits on radioactive material releases from radioactive waste forms to be received in disposable canisters at the Monitored Geologic Repository (MGR) at Yucca Mountain. Specifically, this calculation will provide the basis for criteria to be included in a forthcoming revision of the Waste Acceptance System Requirements Document (WASRD) that limits releases in terms of non-isotope-specific canister release dose-equivalent source terms. These criteria will be developed for the Department of Energy spent nuclear fuel (DSNF) standard canister, the Multicanister Overpack (MCO), the naval spent fuel canister, the High-Level Waste (HLW) canister, the plutonium can-in-canister, and the large Multipurpose Canister (MPC). The shippers of such canisters will be required to demonstrate that they meet these criteria before the canisters are accepted at the MGR. The Quality Assurance program is applicable to this calculation. The work reported in this document is part of the analysis of DSNF and is performed using procedure AP-3.124, Calculations. The work done for this analysis was evaluated according to procedure QAP-2-0, Control of Activities, which has been superseded by AP-2.21Q, Quality Determinations and Planning for Scientific, Engineering, and Regulatory Compliance Activities. This evaluation determined that such activities are subject to the requirements of DOE/RW/0333P, Quality Assurance Requirements and Description (DOE 2000). This work is also prepared in accordance with the development plan titled Design Basis Event Analyses on DOE SNF and Plutonium Can-In-Canister Waste Forms (CRWMS M&O 1999a) and Technical Work Plan For: Department of Energy Spent Nuclear Fuel Work Packages (CRWMS M&O 2000d). This calculation contains no electronic data applicable to any electronic data management system.

  18. On the consistency of risk acceptance criteria with normative theories for decision-making

    Energy Technology Data Exchange (ETDEWEB)

    Abrahamsen, E.B. [University of Stavanger, 4036 Stavanger (Norway)], E-mail: eirik.abrahamsen@uis.no; Aven, T. [University of Stavanger, 4036 Stavanger (Norway)

    2008-12-15

    In evaluation of safety in projects it is common to use risk acceptance criteria to support decision-making. In this paper, we discuss to what extent the risk acceptance criteria is in accordance with the normative theoretical framework of the expected utility theory and the rank-dependent utility theory. We show that the use of risk acceptance criteria may violate the independence axiom of the expected utility theory and the comonotonic independence axiom of the rank-dependent utility theory. Hence the use of risk acceptance criteria is not in general consistent with these theories. The level of inconsistency is highest for the expected utility theory.

  19. On the consistency of risk acceptance criteria with normative theories for decision-making

    International Nuclear Information System (INIS)

    Abrahamsen, E.B.; Aven, T.

    2008-01-01

    In evaluation of safety in projects it is common to use risk acceptance criteria to support decision-making. In this paper, we discuss to what extent the risk acceptance criteria is in accordance with the normative theoretical framework of the expected utility theory and the rank-dependent utility theory. We show that the use of risk acceptance criteria may violate the independence axiom of the expected utility theory and the comonotonic independence axiom of the rank-dependent utility theory. Hence the use of risk acceptance criteria is not in general consistent with these theories. The level of inconsistency is highest for the expected utility theory

  20. Nevada test site defense waste acceptance criteria, certification, and transfer requirements

    International Nuclear Information System (INIS)

    1988-10-01

    The Nevada Test Site (NTS) Defense Waste Acceptance Criteria, Certification and Transfer Requirements establishes procedures and criteria for safe transfer, disposal, and storage of defense transuranic, low-level, and mixed waste at the NTS. Included are an overview of the NTS defense waste management program; the NTS waste acceptance criteria for transuranic, low-level, and mixed wastes; waste certification requirements and guidance; application to submit waste; and requirements for waste transfer and receipt. 5 figs., 16 tabs

  1. Criteria for accepting piping vibrations measured during FFTF plant startup

    International Nuclear Information System (INIS)

    Huang, S.N.

    1981-03-01

    Piping in the Fast Flux Test Facility is subjected to low-amplitude, high cycle vibration over the plant lifetime. Excitation sources include the mechanical vibration induced by main centrifugal pumps, auxiliary reciprocating pumps, EM pumps and possible flow oscillations. Vibration acceptance criteria must be established which will prevent excessive pipe and support fatigue damage when satified. This paper describes the preparation of such criteria against pipe failure used for acceptance testing of the Fast Flux Test Facility main heat transport piping

  2. Hanford Site solid waste acceptance criteria

    International Nuclear Information System (INIS)

    Willis, N.P.; Triner, G.C.

    1991-09-01

    Westinghouse Hanford Company manages the Hanford Site solid waste treatment, storage, and disposal facilities for the US Department of Energy Field Office, Richland under contract DE-AC06-87RL10930. These facilities include radioactive solid waste disposal sites, radioactive solid waste storage areas and hazardous waste treatment, storage, and/or disposal facilities. This manual defines the criteria that must be met by waste generators for solid waste to be accepted by Westinghouse Hanford Company for treatment, storage and/or disposal facilities. It is to be used by all waste generators preparing radioactive solid waste for storage or disposal at the Hanford Site facilities and for all Hanford Site generators of hazardous waste. This manual is also intended for use by Westinghouse Hanford Company solid waste technical staff involved with approval and acceptance of solid waste. The criteria in this manual represent a compilation of state and federal regulations; US Department of Energy orders; Hanford Site requirements; and other rules, regulations, guidelines, and standards as they apply to management of solid waste. Where appropriate, these requirements are included in the manual by reference. It is the intent of this manual to provide guidance to the waste generator in meeting the applicable requirements

  3. Nevada Test Site Waste Acceptance Criteria (NTSWAC), Rev. 7-01

    Energy Technology Data Exchange (ETDEWEB)

    NSTec Environmental Management

    2009-05-01

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office, Nevada Test Site Waste Acceptance Criteria (NTSWAC). The NTSWAC provides the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive waste and mixed low-level waste for disposal. The NTSWAC includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NTS Area 3 and Area 5 Radioactive Waste Management Complex for disposal.

  4. Nevada Test Site Waste Acceptance Criteria (NTSWAC), Rev. 7-01

    International Nuclear Information System (INIS)

    2009-01-01

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office, Nevada Test Site Waste Acceptance Criteria (NTSWAC). The NTSWAC provides the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive waste and mixed low-level waste for disposal. The NTSWAC includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NTS Area 3 and Area 5 Radioactive Waste Management Complex for disposal.

  5. Acceptance criteria for disposal of radioactive wastes in shallow ground and rock cavities

    International Nuclear Information System (INIS)

    1985-01-01

    This document provides an overview of basic information related to waste acceptance criteria for disposal in shallow ground and rock cavity repositories, consisting of a discussion of acceptable waste types. The last item includes identification of those waste characteristics which may influence the performance of the disposal system and as such are areas of consideration for criteria development. The material is presented in a manner similar to a safety assessment. Waste acceptance criteria aimed at limiting the radiation exposure to acceptable levels are presented for each pathway. Radioactive wastes considered here are low-level radioactive wastes and intermediate-level radioactive wastes from nuclear fuel cycle operations and applications of radionuclides in research, medicine and industry

  6. Acceptability criteria for final underground disposal of radioactive waste

    International Nuclear Information System (INIS)

    Sousselier, Y.

    1984-01-01

    Specialists now generally agree that the underground disposal of suitably immobilized radioactive waste offers a means of attaining the basic objective of ensuring the immediate and long-term protection of man and the environment throughout the requisite period of time and in all foreseeable circumstances. Criteria of a more general as well as a more specific nature are practical means through which this basic protection objective can be reached. These criteria, which need not necessarily be quantified, enable the authorities to gauge the acceptability of a given project and provide those responsible for waste management with a basis for making decisions. In short, these principles constitute the framework of a suitably safety-oriented waste management policy. The more general criteria correspond to the protection objectives established by the national authorities on the basis of principles and recommendations formulated by international organizations, in particular the ICRP and the IAEA. They apply to any underground disposal system considered as a whole. The more specific criteria provide a means of evaluating the degree to which the various components of the disposal system meet the general criteria. They must also take account of the interaction between these components. As the ultimate aim is the overall safety of the disposal system, individual components can be adjusted to compensate for the performance of others with respect to the criteria. This is the approach adopted by the international bodies and national authorities in developing acceptability criteria for the final underground radioactive disposal systems to be used during the operational and post-operational phases respectively. The main criteria are reviewed and an attempt is made to assess the importance of the specific criteria according to the different types of disposal systems. (author)

  7. Development on inelastic analysis acceptance criteria for radioactive material transportation packages

    International Nuclear Information System (INIS)

    Ammerman, D.J.; Ludwigsen, J.S.

    1995-01-01

    The response of radioactive material transportation packages to mechanical accident loadings can be more accurately characterized by non-linear dynamic analysis than by the ''Equivalent dynamic'' static elastic analysis typically used in the design of these packages. This more accurate characterization of the response can lead to improved package safety and design efficiency. For non-linear dynamic analysis to become the preferred method of package design analysis, an acceptance criterion must be established that achieves an equivalent level of safety as the currently used criterion defined in NRC Regulatory Guide 7.6 (NRC 1978). Sandia National Laboratories has been conducting a study of possible acceptance criteria to meet this requirement. In this paper non-linear dynamic analysis acceptance criteria based on stress, strain, and strain-energy-density will be discussed. An example package design will be compared for each of the design criteria, including the approach of NRC Regulatory Guide 7.6

  8. A Method to Improve the Software Acceptance Criteria for Nuclear Power Plants

    International Nuclear Information System (INIS)

    Suh, Yong Suk; Park, Heui Youn; Son, Ki Sung; Lee, Ki Hyun; Kim, Hyeon Soo

    2005-01-01

    The license is a mandatory process required by a governmental authority and the certification is a voluntary process administrated by a professional community. A software certification is a result of an assessment that the certified software conforms to required criteria or standards. The certification is used as a committed promise to produce a high quality software, so software acquirers are requiring it from their suppliers. For example, US DoD (Department of Defense) requires an achievement of CMMI-SW (Capability Maturity Model Integration-Software) certification for participating in a major military software project. It is commonly said that the purpose of achieving a certification is to improve the product quality. In the nuclear area, a software certification has been rarely concerned with or required for the software used in a safety function of NPPs (Nuclear Power Plants). The safety critical software for NPPs is accepted by the nuclear regulators when the following three criteria are met: acceptable plans should be prepared to control the software development activities, the plans should be followed in an acceptable software life cycle, and the process should produce acceptable design outputs. The acceptance criteria are so abstractive that the nuclear regulators may assess the software development plans, activities, outputs based on their subjective engineering judgments. This is inevitable because a software has invisible or intangible characteristics. It is hard to assess the totality of a software prior to running it. These have caused the judgments to be biased. The regulators may want some objectiveness in assessing how much capability for software development the supplier possesses. In that case, the software certification can assist them for such an assessment. This paper proposes a method to improve the software acceptance criteria by applying the software certification to the criteria. This will assist the regulators to assess the supplier

  9. On the use of risk acceptance criteria in the offshore oil and gas industry

    International Nuclear Information System (INIS)

    Aven, Terje; Vinnem, Jan Erik

    2005-01-01

    Risk acceptance criteria, as upper limits of acceptable risks, have been used for offshore activities on the Norwegian Continental Shelf for more than 20 years. The common thinking has been that risk analyses and assessments cannot be conducted in a meaningful way without the use of such criteria. The ALARP principle also applies, but the risk acceptance criteria have played a more active role in the assessment processes than seen for example in the UK. Recently there has, however, been a discussion about the suitability of risk acceptance criteria to assess and control risks. The purpose of this paper is to contribute to this discussion by presenting and discussing a risk analysis regime that is not based on the use of risk acceptance criteria at all. We believe that we can do better if cost-effectiveness (in a wide sense) is the ruling thinking rather than adoption of pre-defined risk acceptance limits. This means a closer resemblance with the ALARP principle as adopted in the UK and other countries, but is not a direct application of this practice. Also the building blocks of the common way of applying the ALARP principle are reviewed. The Norwegian offshore oil and gas industry is the starting point, but the discussion is to large extent general

  10. MCO combustible gas management leak test acceptance criteria; TOPICAL

    International Nuclear Information System (INIS)

    SHERRELL, D.L.

    1999-01-01

    Existing leak test acceptance criteria for mechanically sealed and weld sealed multi-canister overpacks (MCO) were evaluated to ensure that MCOs can be handled and stored in stagnant air without compromising the Spent Nuclear Fuel Project's overall strategy to prevent accumulation of combustible gas mixtures within MCO's or within their surroundings. The document concludes that the integrated leak test acceptance criteria for mechanically sealed and weld sealed MCOs (1 x 10(sup -5) std cc/sec and 1 x 10(sup -7) std cc/sec, respectively) are adequate to meet all current and foreseeable needs of the project, including capability to demonstrate compliance with the NFPA 60 Paragraph 3-3 requirement to maintain hydrogen concentrations[within the air atmosphere CSB tubes] t or below 1 vol% (i.e., at or below 25% of the LFL)

  11. Review of issues relevant to acceptable risk criteria for nuclear waste management

    International Nuclear Information System (INIS)

    Cohen, J.J.

    1978-01-01

    Development of acceptable risk criteria for nuclear waste management requires the translation of publicly determined goals and objectives into definitive issues which, in turn, require resolution. Since these issues are largely of a subjective nature, they cannot be resolved by technological methods. Development of acceptable risk criteria might best be accomplished by application of a systematic methodology for the optimal implementation of subjective values. Multi-attribute decision analysis is well suited for this purpose

  12. Waste-acceptance criteria and risk-based thinking for radioactive-waste classification

    International Nuclear Information System (INIS)

    Lowenthal, M.D.

    1998-01-01

    The US system of radioactive-waste classification and its development provide a reference point for the discussion of risk-based thinking in waste classification. The official US system is described and waste-acceptance criteria for disposal sites are introduced because they constitute a form of de facto waste classification. Risk-based classification is explored and it is found that a truly risk-based system is context-dependent: risk depends not only on the waste-management activity but, for some activities such as disposal, it depends on the specific physical context. Some of the elements of the official US system incorporate risk-based thinking, but like many proposed alternative schemes, the physical context of disposal is ignored. The waste-acceptance criteria for disposal sites do account for this context dependence and could be used as a risk-based classification scheme for disposal. While different classes would be necessary for different management activities, the waste-acceptance criteria would obviate the need for the current system and could better match wastes to disposal environments saving money or improving safety or both

  13. Why risk acceptance criteria need to be defined by the authorities and not the industry?

    International Nuclear Information System (INIS)

    Abrahamsen, Eirik Bjorheim; Aven, Terje

    2012-01-01

    In various industries it is common to use risk acceptance criteria to support decision-making. The criteria are seen as absolute in the sense that measures need to be implemented if the criteria are not met. In Norway the petroleum regulations state that the operator has a duty to formulate risk acceptance criteria relating to major accidents and to the environment. This practice is in line with the internal control principle, which states that the operator has the full responsibility for identifying the hazards and seeing that they are controlled. In this paper we discuss the rationale for this practice. The expected utility theory, which is the backbone for all economic thinking, is used as a basis for the discussion. We show that if risk acceptance criteria are to be introduced as a risk management tool, they should be formulated by the authorities, as is the common scheme seen in many countries and industries, for example in the UK. Risk acceptance criteria formulated by the industry would not in general serve the interest of the society as a whole.

  14. 78 FR 65007 - Inspections, Tests, Analyses, and Acceptance Criteria; Vogtle Electric Generating Plant, Unit 3

    Science.gov (United States)

    2013-10-30

    ... NUCLEAR REGULATORY COMMISSION [Docket No. 052-00026; NRC-2008-0252] Inspections, Tests, Analyses, and Acceptance Criteria; Vogtle Electric Generating Plant, Unit 3 AGENCY: Nuclear Regulatory Commission. ACTION: Determination of inspections, tests, analyses, and acceptance criteria completion...

  15. 78 FR 53483 - Inspections, Tests, Analyses, and Acceptance Criteria; Vogtle Electric Generating Plant, Unit 3

    Science.gov (United States)

    2013-08-29

    ... NUCLEAR REGULATORY COMMISSION [Docket No. 052-00025; NRC-2008-0252] Inspections, Tests, Analyses, and Acceptance Criteria; Vogtle Electric Generating Plant, Unit 3 AGENCY: Nuclear Regulatory Commission. ACTION: Determination of inspections, tests, analyses, and acceptance criteria (ITAAC) completion...

  16. 78 FR 53484 - Inspections, Tests, Analyses, and Acceptance Criteria; Vogtle Electric Generating Plant, Unit 4

    Science.gov (United States)

    2013-08-29

    ... NUCLEAR REGULATORY COMMISSION [Docket No. 052-00026; NRC-2008-0252] Inspections, Tests, Analyses, and Acceptance Criteria; Vogtle Electric Generating Plant, Unit 4 AGENCY: Nuclear Regulatory Commission. ACTION: Determination of inspections, tests, analyses, and acceptance criteria (ITAAC) completion...

  17. 78 FR 38411 - Vogtle Electric Generating Plant, Unit 4; Inspections, Tests, Analyses, and Acceptance Criteria

    Science.gov (United States)

    2013-06-26

    ... Plant, Unit 4; Inspections, Tests, Analyses, and Acceptance Criteria AGENCY: Nuclear Regulatory Commission. ACTION: Determination of inspections, tests, analyses, and acceptance criteria completion. SUMMARY: The U.S. Nuclear Regulatory Commission (NRC) staff has determined that the inspections, tests...

  18. Synthetic seismic acceleration time-histories and their acceptance criteria

    International Nuclear Information System (INIS)

    Xu Hong

    1996-01-01

    In seismic dynamic response analysis of structures and equipment, time-history analysis is now widely used. The 3-D seismic acceleration time-histories or 3-D seismic displacement time-histories are required in the 3-D seismic dynamic response analysis as the seismic excitation input data. Because of the lack of actual acceleration time-histories for the field where the structures or equipment are installed, the general practice is to use the synthetic seismic acceleration time-histories, which are derived from the design seismic response spectra of the field, as the seismic excitation input data. However, from one specified design response spectrum indefinite solutions of acceleration time-histories can be derived depending on the values of the input parameters. Not all the derived synthetic time-histories can be used as seismic excitation input data. Only those which meet the acceptance criteria can be used. The factors (input parameters), which will affect the time-history solution from a specified seismic response spectrum, and the acceptance criteria are discussed

  19. Establishing seismic design criteria to achieve an acceptable seismic margin

    International Nuclear Information System (INIS)

    Kennedy, R.P.

    1997-01-01

    In order to develop a risk based seismic design criteria the following four issues must be addressed: (1) What target annual probability of seismic induced unacceptable performance is acceptable? (2). What minimum seismic margin is acceptable? (3) Given the decisions made under Issues 1 and 2, at what annual frequency of exceedance should the Safe Shutdown Earthquake ground motion be defined? (4) What seismic design criteria should be established to reasonably achieve the seismic margin defined under Issue 2? The first issue is purely a policy decision and is not addressed in this paper. Each of the other three issues are addressed. Issues 2 and 3 are integrally tied together so that a very large number of possible combinations of responses to these two issues can be used to achieve the target goal defined under Issue 1. Section 2 lays out a combined approach to these two issues and presents three potentially attractive combined resolutions of these two issues which reasonably achieves the target goal. The remainder of the paper discusses an approach which can be used to develop seismic design criteria aimed at achieving the desired seismic margin defined in resolution of Issue 2. Suggestions for revising existing seismic design criteria to more consistently achieve the desired seismic margin are presented

  20. HWVP compliance with the Hanford site solid waste acceptance criteria

    International Nuclear Information System (INIS)

    Bromm, R.; Ornelas, J.; Fundingsland, S.; Shah, K.

    1993-01-01

    In order to ensure that the Hanford Waste Vitrification Project (HWVP) will meet solid waste acceptance criteria, a review of the criteria was performed. The primary purpose of the study was to evaluate the modifications that will be required to bring the HWVP into compliance for secondary waste which will be generated during normal operations of the facility. To accomplish this objective, the current HWVP design was evaluated based on the criteria established. Once the non-compliance areas and potentially non-compliance areas were identified, alternative plant design modifications were proposed. This paper summarizes the results and recommendations of that study

  1. Criteria for risk acceptance: a health physicist's view

    International Nuclear Information System (INIS)

    Hull, A. P.

    1977-01-01

    While energy need (or demand) and the risks of energy production and use may be objectively quantified, risk acceptance embodies a subjective element of preferences and values. Yet, as demonstrated by the nuclear controversy in the United States, public acceptance is essential to the beneficial uses of radiation. The statement of the objectives and purposes of the Health Physics Society and our application of it are proposed as offering useful criteria for risk acceptance. The principle of comparing risk with a number of those regularly accepted in everyday life is emphasized. On this basis, it is concluded that the expenditures to attain currently applicable or proposed 'as low as practicable' (or 'as low as readily achievable') levels for the nuclear fuel cycle are disproportionate to those addressed to other sources of general public exposure to radiation. They are also disproportionate compared to those addressed to a variety of public health risks. It is suggested that sensible priorities for radiation and public health protection might be achieved by the application of a de minimus negligible (but nonzero) level of probable risk. (Research supported by the U.S. Energy Research and Development Administration.)

  2. Typical design/qualification acceptance criteria for newly installed pipelines and equipment components of VVER-type NPPs

    International Nuclear Information System (INIS)

    Masopust, R.

    2003-01-01

    This paper describes in general the typical design/qualification acceptance criteria and seismic acceptance criteria in particular that are applicable for important to safety newly installed pipelines and equipment components of VVER-type already existing NPPs, specifically during the design verification phase of this newly installed equipment. These criteria are currently used for VVER 440-213 and VVER 1000 NPPs in Czech Republic and in Slovakia. The similar criteria are also used in Hungary. (author)

  3. A comparison and cross-reference of commercial low-level radioactive waste acceptance criteria

    International Nuclear Information System (INIS)

    Kerr, T.A.

    1997-04-01

    This document, prepared by the National Low-Level Waste Management Program at the Idaho National Engineering and Environmental Laboratory, is a comparison and cross-reference of commercial low-level radioactive waste acceptance criteria. Many of these are draft or preliminary criteria as well as implemented criteria at operating low-level radioactive waste management facilities. Waste acceptance criteria from the following entities are included: US Nuclear Regulatory Commission, South Carolina, Washington, Utah, Nevada, California, illinois, Texas, North Carolina, Nebraska, Pennsylvania, New York, and the Midwest Compact Region. Criteria in the matrix include the following: physical form, chemical form, liquid limits, void space in packages, concentration averaging, types of packaging, chelating agents, solidification media, stability requirements, sorptive media, gas, oil, biological waste, pyrophorics, source material, special nuclear material, package dimensions, incinerator ash, dewatered resin, transuranics, and mixed waste. Each criterion in the matrix is cross-referenced to its source document so that exact requirements can be determined

  4. Waste acceptance criteria study: Volume 2, Appendixes: Final report

    International Nuclear Information System (INIS)

    Johnson, E.R.; McLeod, N.B.; McBride, J.A.

    1988-09-01

    These appendices to the report on Waste Acceptance Criteria have been published as a separate volume for the convenience of the reader. They consist of the text of the 10CFR961 Contract for disposal of spent fuel, estimates of the cost (savings) to the DOE system of accepting different forms of spent fuel, estimates of costs of acceptance testing/inspection of spent fuel, illustrative specifications and procedures, and the resolution of comments received on a preliminary draft of the report. These estimates of costs contained herein preliminary and are intended only to demonstrate the trends in costs, the order of magnitude involved, and the methodology used to develop the costs. The illustrative specifications and procedures included herein have been developed for the purpose of providing a starting point for the development of a consensus on such matters between utilities and DOE

  5. Acceptance criteria for the ITER divertor vertical target

    International Nuclear Information System (INIS)

    Fouquet, S.; Schlosser, J.; Merola, M.; Durocher, A.; Escourbiac, F.; Grosman, A.; Missirlian, M.; Portafaix, C.

    2006-01-01

    In the frame of the toroidal pump limiter fabrication for Tore Supra, CEA developed a large experience of infrared test for acceptance of high heat flux components armoured with carbon fibre composite flat tiles. The test is based on a thermal transient induced by an alternative hot/cold water flow in the heat sink structure. The tile surface temperature transients are compared with those of a reference element, the maximum difference for each tile leading to a value called ΔT ref m ax . This method is proposed for the commissioning of plasma facing components for the ITER divertor vertical target. This paper describes the determination of the best acceptance criteria for the 'monoblock' geometry of the carbon part. First, it has been shown that the location and the extension of the defects could reliably be determined by monitoring both top and lateral surfaces during the test. Second, it was possible to fix an acceptance method based on ΔT ref m ax . Samples with calibrated defects are now under fabrication to validate the results

  6. Procedures and acceptance criteria for PAS-1 cask inspections

    International Nuclear Information System (INIS)

    Mercado, J.E.

    1998-01-01

    The procedures and acceptance criteria that comprise this document were prepared to support a one-time test to certify two PAS-1 casks in accordance with US Department of Energy Certificate of Compliance US A/9184/B(U), which was issued in 1998. The specific inspections addressed in this document are the visual weld inspection and a dimensional inspection of the primary containment vessel

  7. 21 CFR 212.70 - What controls and acceptance criteria must I have for my finished PET drug products?

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 4 2010-04-01 2010-04-01 false What controls and acceptance criteria must I have... POSITRON EMISSION TOMOGRAPHY DRUGS (Eff. 12-12-2011) Finished Drug Product Controls and Acceptance § 212.70 What controls and acceptance criteria must I have for my finished PET drug products? (a) Specifications...

  8. Testing the validity and acceptability of the diagnostic criteria for Hoarding Disorder: a DSM-5 survey.

    Science.gov (United States)

    Mataix-Cols, D; Fernández de la Cruz, L; Nakao, T; Pertusa, A

    2011-12-01

    The DSM-5 Obsessive-Compulsive Spectrum Sub-Workgroup is recommending the creation of a new diagnostic category named Hoarding Disorder (HD). The validity and acceptability of the proposed diagnostic criteria have yet to be formally tested. Obsessive-compulsive disorder/hoarding experts and random members of the American Psychiatric Association (APA) were shown eight brief clinical vignettes (four cases meeting criteria for HD, three with hoarding behaviour secondary to other mental disorders, and one with subclinical hoarding behaviour) and asked to decide the most appropriate diagnosis in each case. Participants were also asked about the perceived acceptability of the criteria and whether they supported the inclusion of HD in the main manual. Altogether, 211 experts and 48 APA members completed the survey (30% and 10% response rates, respectively). The sensitivity and specificity of the HD diagnosis and the individual criteria were high (80-90%) across various types of professionals, irrespective of their experience with hoarding cases. About 90% of participants in both samples thought the criteria would be very/somewhat acceptable for professionals and sufferers. Most experts (70%) supported the inclusion of HD in the main manual, whereas only 50% of the APA members did. The proposed criteria for HD have high sensitivity and specificity. The criteria are also deemed acceptable for professionals and sufferers alike. Training of professionals and the development and validation of semi-structured diagnostic instruments should improve diagnostic accuracy even further. A field trial is now needed to confirm these encouraging findings with real patients in real clinical settings.

  9. Strain-based plastic instability acceptance criteria for ferritic steel safety class 1 nuclear components under level D

    International Nuclear Information System (INIS)

    Kim, Ji Su; Lee, Han Sang; Kim, Yun Jae; Kim, Jong Sung; Kim, Jin Won

    2015-01-01

    This paper proposes strain-based acceptance criteria for assessing plastic instability of the safety class 1 nuclear components made of ferritic steel during level D service loads. The strain-based criteria were proposed with two approaches: (1) a section average approach and (2) a critical location approach. Both approaches were based on the damage initiation point corresponding to the maximum load-carrying capability point instead of the fracture point via tensile tests and finite element analysis (FEA) for the notched specimen under uni-axial tensile loading. The two proposed criteria were reviewed from the viewpoint of design practice and philosophy to select a more appropriate criterion. As a result of the review, it was found that the section average approach is more appropriate than the critical location approach from the viewpoint of design practice and philosophy. Finally, the criterion based on the section average approach was applied to a simplified reactor pressure vessel (RPV) outlet nozzle subject to SSE loads. The application shows that the strain-based acceptance criteria can consider cumulative damages caused by the sequential loads unlike the stress-based acceptance criteria and can reduce the over conservatism of the stress-based acceptance criteria, which often occurs for level D service loads.

  10. Strain-based plastic instability acceptance criteria for ferritic steel safety class 1 nuclear components under level D

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ji Su; Lee, Han Sang; Kim, Yun Jae [Dept. of Mechanical Engineering, Korea University, Seoul (Korea, Republic of); Kim, Jong Sung [Dept. of Mechanical Engineering, Sunchon National University, Suncheon (Korea, Republic of); Kim, Jin Won [Dept. of Nuclear Engineering, Chosun University, Gwangju (Korea, Republic of)

    2015-04-15

    This paper proposes strain-based acceptance criteria for assessing plastic instability of the safety class 1 nuclear components made of ferritic steel during level D service loads. The strain-based criteria were proposed with two approaches: (1) a section average approach and (2) a critical location approach. Both approaches were based on the damage initiation point corresponding to the maximum load-carrying capability point instead of the fracture point via tensile tests and finite element analysis (FEA) for the notched specimen under uni-axial tensile loading. The two proposed criteria were reviewed from the viewpoint of design practice and philosophy to select a more appropriate criterion. As a result of the review, it was found that the section average approach is more appropriate than the critical location approach from the viewpoint of design practice and philosophy. Finally, the criterion based on the section average approach was applied to a simplified reactor pressure vessel (RPV) outlet nozzle subject to SSE loads. The application shows that the strain-based acceptance criteria can consider cumulative damages caused by the sequential loads unlike the stress-based acceptance criteria and can reduce the over conservatism of the stress-based acceptance criteria, which often occurs for level D service loads.

  11. Multi-Canister Overpack (MCO) Combustible Gas Management Leak Test Acceptance Criteria (OCRWM)

    International Nuclear Information System (INIS)

    SHERRELL, D.L.

    2000-01-01

    The purpose of this document is to support the Spent Nuclear Fuel Project's combustible gas management strategy while avoiding the need to impose any requirements for oxygen free atmospheres within storage tubes that contain multi-canister overpacks (MCO). In order to avoid inerting requirements it is necessary to establish and confirm leak test acceptance criteria for mechanically sealed and weld sealed MCOs that are adequte to ensure that, in the unlikely event the leak test results for any MCO were to approach either of those criteria, it could still be handled and stored in stagnant air without compromising the SNF Project's overall strategy to prevent accumulation of combustible gas mixtures within MCOs or within their surroundings. To support that strategy, this document: (1) establishes combustible gas management functions and minimum functional requirements for the MCO's mechanical seals and closure weld(s); (2) establishes a maximum practical value for the minimum required initial MCO inert backfill gas pressure; and (3) based on items 1 and 2, establishes and confirms leak test acceptance criteria for the MCO's mechanical seal and final closure weld(s)

  12. The use of acceptability criteria for radiological risk at AWE Aldermaston

    International Nuclear Information System (INIS)

    Thurston, B.B.; Tutt, K.J.; Zabierek, G.A.

    1989-01-01

    The limit-line approach to setting acceptable risk criteria for nuclear power plants is in general use in the United Kingdom. The Atomic Weapons Establishment (AWE) is a Ministry of Defence Establishment which contains a number of nuclear material processing facilities. Limit-line risk criteria have been used for some years to provide a framework within which identified hazards may be judged in a systematic manner, rather than on an ad hoc basis. This paper describes how this is applied to both new facilities and to changes made to existing ones including decommissioning. (author)

  13. Acceptance criteria for deposition of low-level and intermediate-level radiation levels radioactive wastes

    International Nuclear Information System (INIS)

    2002-09-01

    This norm establishes the criteria for acceptance low and intermediate radiation level for safe deposition in repositories, for assuring the protection of workers, population and environment against the hazardous effects of the ionizing radiations. The criteria of this norm applies to the low and intermediate radiation levels

  14. Technical Basis For Radiological Acceptance Criteria For Uranium At The Y-12 National Security Complex

    Energy Technology Data Exchange (ETDEWEB)

    Veinot, K. G.

    2009-07-22

    The purpose of this report is to establish radiological acceptance criteria for uranium. Other factors for acceptance not considered include criticality safety concerns, contaminants to the process stream, and impacts to the Safety Basis for the affected facilities. Three types of criteria were developed in this report. They include limits on external penetrating and non-penetrating radiation and on the internal hazard associated with inhalation of the material. These criteria are intended to alleviate the need for any special controls beyond what are normally utilized for worker protection from uranium hazards. Any proposed exceptions would require case-by-case evaluations to determine cost impacts and feasibility. Since Y-12 has set rigorous ALARA goals for worker doses, the external limits are based on assumptions of work time involved in the movement of accepted material plus the desire that external doses normally received are not exceeded, and set so that no special personnel monitoring would be required. Internal hazard controls were established so that dose contributions from non-uranium nuclides would not exceed 10% of that expected from the uranium component. This was performed using a Hazard Index (HI) previously established for work in areas contaminated with non-uranium nuclides. The radiological acceptance criteria for uranium are summarized in Table 1. Note that these limits are based on the assumption that radioactive daughter products have reached equilibrium.

  15. Managing Hanford Site solid waste through strict acceptance criteria

    International Nuclear Information System (INIS)

    Jasen, W.G.; Pierce, R.D.; Willis, N.P.

    1993-02-01

    Various types of waste have been generated during the 50-year history of the Hanford Site. Regulatory changes in the last 20 years have provided the emphasis for better management of these wastes. Interpretations of the Atomic Energy Act of 1954 (AEA) and the Resource Conservation and Recovery Act of 1976 (RCRA) have led to the definition of a group of wastes called radioactive mixed wastes (RMW). As a result of the radioactive and hazardous properties of these wastes, strict management programs have been implemented for the management of these wastes. Solid waste management is accomplished through a systems performance approach to waste management that used best-demonstrated available technology (BDAT) and best management practices. The solid waste program at the Hanford Site strives to integrate all aspects of management relative to the treatment, storage and disposal (TSD) of solid waste. Often there are many competing and important needs. It is a difficult task to balance these needs in a manner that is both equitable and productive. Management science is used to help the process of making decisions. Tools used to support the decision making process include five-year planning, cost estimating, resource allocation, performance assessment, waste volume forecasts, input/output models, and waste acceptance criteria. The purpose of this document is to describe how one of these tools, waste acceptance criteria, has helped the Hanford Site manage solid wastes

  16. Qualitative acceptance criteria for radioactive wastes to be disposed of in deep geological formations

    International Nuclear Information System (INIS)

    1990-05-01

    The present Safety Guide has to be seen as a companion document to the IAEA Safety Series No. 99. It is concerned with the waste form which is an important component of the overall disposal system. Because of the broad range of waste types and conditioned forms and variations in the sites, designs and constructional approaches being considered for deep geological repositories, this report necessarily approaches the waste acceptance criteria in a general way, recognizing that the assignment of quantitative limits to these criteria has to be the responsibility of national authorities. The main objective of this Safety Guide is to set out qualitative waste acceptance criteria as a basis for specifying quantitative limits for the waste forms and packages which are intended to be disposed of in deep geological repositories. It should serve as guidance for assigning such parameter values which would fully comply with the safety assessment and performance of a waste disposal system as a whole. This document is intended to serve both national authorities and regulatory bodies involved in the development of deep underground disposal systems. The qualitative waste acceptance criteria dealt with in the present Safety Guide are primarily concerned with the disposal of high level, intermediate level and long-lived alpha bearing wastes in deep geological repositories. Although some criteria are also applicable in other waste disposal concepts, it has to be borne in mind that the set of criteria presented here shall ensure the isolation capability of a waste disposal system for periods of time much longer than for other waste streams with shorter lifetimes. 51 refs, 1 tab

  17. Design loads, loading combinations and structural acceptance criteria for BWR containments in the United States

    International Nuclear Information System (INIS)

    Edwards, N.W.

    1979-01-01

    The definition of loads, loading combinations, and structural acceptance criteria used for the design and evaluation of BWR containments in the Unites States has become much more comprehensive over the past decade. The Mark I pressure suppression containment vessels were designed for a static design pressure, a design temperature, dead load and static equivalent earthquake. The current Mark III containments are being designed to accommodate many more loads such as safety relief valve discharge loads, and suppression pool hydrodynamic loadings associated with the steam condensation phenomena as well as pressure and temperature transients for a range of pipe break sizes. Consistent with the more comprehensive definition of loads and loading combinations, the ASME Code presently establishes structural acceptance criteria with different margins of safety by the definition of Service Level Assignments A, B, C and D. Acting in a responsible manner, United States utilities are currently evaluating and modifying existing containment vessels to account for the more detailed load definition and structural acceptance criteria. (orig.)

  18. A Study On Critical Thinning In Thin-walled Tube Bending Of Al-Alloy 5052O Via Coupled Ductile Fracture Criteria

    International Nuclear Information System (INIS)

    Li Heng; Yang He; Zhan Mei

    2010-01-01

    Thin-walled tube bending(TWTB) method of Al-alloy tube has attracted wide applications in aerospace, aviation and automobile,etc. While, under in-plane double tensile stress states at the extrados of bending tube, the over-thinning induced ductile fracture is one dominant defect in Al-alloy tube bending. The main objective of this study is to predict the critical wall-thinning of Al-alloy tube bending by coupling two ductile fracture criteria(DFCs) into FE simulation. The DFCs include Continuum Damage Mechanics(CDM)-based model and GTN porous model. Through the uniaxial tensile test of the curved specimen, the basic material properties of the Al-alloy 5052O tube is obtained; via the inverse problem solution, the damage parameters of both the two fracture criteria are interatively determined. Thus the application study of the above DFCs in the TWTB is performed, and the more reasonable one is selected to obtain the critical thinning of Al-alloy tube in bending. The virtual damage initiation and evolution (when and where the ductile fracture occurs) in TWTB are investigated, and the fracture mechanisms of the voided Al-alloy tube in tube bending are consequently discussed.

  19. Criteria required for an acceptable point-of-care test for UTI detection: Obtaining consensus using the Delphi technique.

    Science.gov (United States)

    Weir, Nichola-Jane M; Pattison, Sally H; Kearney, Paddy; Stafford, Bob; Gormley, Gerard J; Crockard, Martin A; Gilpin, Deirdre F; Tunney, Michael M; Hughes, Carmel M

    2018-01-01

    Urinary Tract Infections (UTIs) are common bacterial infections, second only to respiratory tract infections and particularly prevalent within primary care. Conventional detection of UTIs is culture, however, return of results can take between 24 and 72 hours. The introduction of a point of care (POC) test would allow for more timely identification of UTIs, facilitating improved, targeted treatment. This study aimed to obtain consensus on the criteria required for a POC UTI test, to meet patient need within primary care. Criteria for consideration were compiled by the research team. These criteria were validated through a two-round Delphi process, utilising an expert panel of healthcare professionals from across Europe and United States of America. Using web-based questionnaires, panellists recorded their level of agreement with each criterion based on a 5-point Likert Scale, with space for comments. Using median response, interquartile range and comments provided, criteria were accepted/rejected/revised depending on pre-agreed cut-off scores. The first round questionnaire presented thirty-three criteria to the panel, of which 22 were accepted. Consensus was not achieved for the remaining 11 criteria. Following response review, one criterion was removed, while after revision, the remaining 10 criteria entered the second round. Of these, four were subsequently accepted, resulting in 26 criteria considered appropriate for a POC test to detect urinary infections. This study generated an approved set of criteria for a POC test to detect urinary infections. Criteria acceptance and comments provided by the healthcare professionals also supports the development of a multiplex point of care UTI test.

  20. Characteristics of radioactive waste forms conditioned for storage and disposal: Guidance for the development of waste acceptance criteria

    International Nuclear Information System (INIS)

    1983-04-01

    This report attempts to review the characteristics of the individual components of the waste package, i.e. the waste form and the container, in order to formulate, where appropriate, quidelines for the development of practical waste acceptance criteria. Primarily the criteria for disposal are considered, but if more stringent criteria are expected to be necessary for storage or transportation prior to the disposal, these will be discussed. The report will also suggest test areas which will aid the development of the final waste acceptance criteria

  1. Summary of research and development activities in support of waste acceptance criteria for WIPP

    International Nuclear Information System (INIS)

    Hunter, T.O.

    1979-11-01

    The development of waste acceptance criteria for the Waste Isolation Pilot Plant (WIPP) is summarized. Specifications for acceptable waste forms are included. Nine program areas are discussed. They are: TRU characterization, HLW interactions, thermal/structural interactions, nuclide migration, permeability, brine migration, borehole plugging, operation/design support, and instrumentation development. Recommendations are included

  2. Sample acceptance time criteria, electronic issue and alloimmunisation in thalassaemia.

    Science.gov (United States)

    Trompeter, S; Baxter, L; McBrearty, M; Zatkya, E; Porter, J

    2015-12-01

    To determine the safety of a 1-week acceptance criteria of sample receipt in laboratory to transfusion commencement in transfusion dependent thalassaemia with respect to alloimmunisation. To determine the safety of electronic issue of blood components in such a setting. Retrospective audit of alloimmunisation (1999-2012) and blood exposure in registered thalassaemia patients at a central London thalassaemia centre where the acceptance criteria for the group and save sample from arrival in the laboratory to the time of issue of blood for transfusion for someone who has been transfused in the last 28 days was 1 week, and there was electronic issue protocol for patients who have always had a negative antibody screen (other than temporary positivity in pregnant women receiving prophylactic anti-D or anti Le-a, Anti Le-b and Anti P1 that are no longer detectable). There were 133 patients with thalassemia variants regularly attending UCLH for review. A total of 105 patients had transfusion dependent thalassaemia (TDT) (7 E-beta thalassaemia, 98 beta thalassaemia major). Ten of the 84 patients who received their transfusions at UCLH were alloimmunised. Seven of them had been alloimmunised prior to arrival at UCLH. Only two patients developed antibodies at UCLH during this period. The prevalence of alloantibody formation of 2% in UCLH transfused patients, with presumptive incidence of 0.01 alloantibodies per 100 units or 0·001 immunisations per person per year compares favourably with other reported series and suggests that 1 week interval with appropriate electronic issue is acceptable practice. © 2015 British Blood Transfusion Society.

  3. Waste acceptance criteria for the Waste Isolation Pilot Plant

    International Nuclear Information System (INIS)

    1996-04-01

    The Waste Isolation Pilot Plant (WIPP) Waste Acceptance Criteria (WAC), DOE/WIPP-069, was initially developed by a U.S. Department of Energy (DOE) Steering Committee to provide performance requirements to ensure public health and safety as well as the safe handling of transuranic (TRU) waste at the WIPP. This revision updates the criteria and requirements of previous revisions and deletes those which were applicable only to the test phase. The criteria and requirements in this document must be met by participating DOE TRU Waste Generator/Storage Sites (Sites) prior to shipping contact-handled (CH) and remote-handled (RH) TRU waste forms to the WIPP. The WIPP Project will comply with applicable federal and state regulations and requirements, including those in Titles 10, 40, and 49 of the Code of Federal Regulations (CFR). The WAC, DOE/WIPP-069, serves as the primary directive for assuring the safe handling, transportation, and disposal of TRU wastes in the WIPP and for the certification of these wastes. The WAC identifies strict requirements that must be met by participating Sites before these TRU wastes may be shipped for disposal in the WIPP facility. These criteria and requirements will be reviewed and revised as appropriate, based on new technical or regulatory requirements. The WAC is a controlled document. Revised/changed pages will be supplied to all holders of controlled copies

  4. Identification of permit and waste acceptance criteria provisions requiring modification for acceptance of commercial mixed waste

    International Nuclear Information System (INIS)

    1994-03-01

    In October 1990, representatives of States and compact regions requested that the US Department of Energy (DOE) explore an agreement with host States and compact regions under which DOE would accept commercial mixed low-level radioactive waste (LLW) at DOE's own treatment and disposal facilities. A program for DOE management of commercial mixed waste is made potentially more attractive in light of the low commercial mixed waste volumes, high regulatory burdens, public opposition to new disposal sites, and relatively high cost of constructing commercial disposal facilities. Several studies were identified as essential in determining the feasibility of DOE accepting commercial mixed waste for disposal. The purpose of this report is to identify any current or proposed waste acceptance criteria (WAC) or Resource Conservation and Recovery Act (RCRA) provisions that would have to be modified for commercial mixed waste acceptance at specified DOE facilities. Following the introduction, Section 2 of this report (a) provides a background summary of existing and proposed mixed waste disposal facilities at each DOE site, and (b) summarizes the status of any RCRA Part B permit and WAC provisions relating to the disposal of mixed waste, including provisions relating to acceptance of offsite waste. Section 3 provides overall conclusions regarding the current status and permit modifications that must be implemented in order to grant DOE sites authority under their permits to accept commercial mixed waste for disposal. Section 4 contains a list of references

  5. Definition of acceptance criteria for the ITER divertor plasma-facing components through systematic experimental analysis

    International Nuclear Information System (INIS)

    Escourbiac, F; Richou, M; Guigon, R; Durocher, A; Schlosser, J; Grosman, A; Constans, S; Merola, M; Riccardi, B

    2009-01-01

    Experience has shown that a critical part of the high-heat flux (HHF) plasma-facing component (PFC) is the armour to heat sink bond. An experimental study was performed in order to define acceptance criteria with regards to thermal hydraulics and fatigue performance of the International Thermonuclear Experimental Reactor (ITER) divertor PFCs. This study, which includes the manufacturing of samples with calibrated artificial defects relevant to the divertor design, is reported in this paper. In particular, it was concluded that defects detectable with non-destructive examination (NDE) techniques appeared to be acceptable during HHF experiments relevant to heat fluxes expected in the ITER divertor. On the basis of these results, a set of acceptance criteria was proposed and applied to the European vertical target medium-size qualification prototype: 98% of the inspected carbon fibre composite (CFC) monoblocks and 100% of tungsten (W) monoblock and flat tiles elements (i.e. 80% of the full units) were declared acceptable.

  6. Definition of acceptance criteria for the ITER divertor plasma-facing components through systematic experimental analysis

    Science.gov (United States)

    Escourbiac, F.; Richou, M.; Guigon, R.; Constans, S.; Durocher, A.; Merola, M.; Schlosser, J.; Riccardi, B.; Grosman, A.

    2009-12-01

    Experience has shown that a critical part of the high-heat flux (HHF) plasma-facing component (PFC) is the armour to heat sink bond. An experimental study was performed in order to define acceptance criteria with regards to thermal hydraulics and fatigue performance of the International Thermonuclear Experimental Reactor (ITER) divertor PFCs. This study, which includes the manufacturing of samples with calibrated artificial defects relevant to the divertor design, is reported in this paper. In particular, it was concluded that defects detectable with non-destructive examination (NDE) techniques appeared to be acceptable during HHF experiments relevant to heat fluxes expected in the ITER divertor. On the basis of these results, a set of acceptance criteria was proposed and applied to the European vertical target medium-size qualification prototype: 98% of the inspected carbon fibre composite (CFC) monoblocks and 100% of tungsten (W) monoblock and flat tiles elements (i.e. 80% of the full units) were declared acceptable.

  7. Definition of acceptance criteria for the ITER divertor plasma-facing components through systematic experimental analysis

    Energy Technology Data Exchange (ETDEWEB)

    Escourbiac, F; Richou, M; Guigon, R; Durocher, A; Schlosser, J; Grosman, A [CEA/IRFM, F-13108, Saint-Paul-lez-Durance (France); Constans, S [AREVA-NP, Le Creusot (France); Merola, M [ITER Organization, Cadarache (France); Riccardi, B [Fusion For Energy, Barcelona (Spain)], E-mail: frederic.escourbiac@cea.fr

    2009-12-15

    Experience has shown that a critical part of the high-heat flux (HHF) plasma-facing component (PFC) is the armour to heat sink bond. An experimental study was performed in order to define acceptance criteria with regards to thermal hydraulics and fatigue performance of the International Thermonuclear Experimental Reactor (ITER) divertor PFCs. This study, which includes the manufacturing of samples with calibrated artificial defects relevant to the divertor design, is reported in this paper. In particular, it was concluded that defects detectable with non-destructive examination (NDE) techniques appeared to be acceptable during HHF experiments relevant to heat fluxes expected in the ITER divertor. On the basis of these results, a set of acceptance criteria was proposed and applied to the European vertical target medium-size qualification prototype: 98% of the inspected carbon fibre composite (CFC) monoblocks and 100% of tungsten (W) monoblock and flat tiles elements (i.e. 80% of the full units) were declared acceptable.

  8. Criteria for accepting piping thermal expansion movements during FFTF plant startup

    International Nuclear Information System (INIS)

    Clark, G.L.; Anderson, M.J.

    1981-03-01

    A deflection measurement program was conducted as a final step in the design qualification of the Fast Flux Test Facility liquid sodium piping. Measurements were obtained from the ambient empty position, through the 400 0 F (204 0 C) sodium fill, to an 800 0 F (427 0 C) maximum iso-thermal test condition. The program was designed to confirm that the pipe responded as predicted under both deadweight and thermal expansion loads. This paper describes the design of the test programs; the criteria used to select appropriate measurement locations from the approximately 4000 supports used on this pipe; and the criteria used to accept test results

  9. Development of Waste Acceptance Criteria at 221-U Building: Initial Flow and Transport Scoping Calculations

    Energy Technology Data Exchange (ETDEWEB)

    Freedman, Vicky L.; Zhang, Z. F.; Keller, Jason M.; Chen, Yousu

    2007-05-30

    This report documents numerical flow and transport simulations performed that establish initial waste acceptance criteria for the potential waste streams that may be safely sequestered in the 221-U Building and similar canyon structures. Specifically, simulations were executed to identify the maximum loading of contaminant mass (without respect to volume) that can be emplaced within the 221-U Building with no more than 1 pCi/m2 of contaminant migrating outside the structure within a 1,000 year time period. The initial scoping simulations were executed in one dimension to assess important processes, and then two dimensions to establish waste acceptance criteria. Two monolithic conditions were assessed: (1) a grouted canyon monolith; and (2) a canyon monolith filled with sand, both assuming no cracks or fissures were present to cause preferential transport. A three-staged approach was taken to account for different processes that may impact the amount of contaminant that can be safely sequestered in canyon structure. In the first stage, flow and transport simulations established waste acceptance criteria based on a linear (Kd) isotherm approach. In the second stage, impacts on thermal loading were examined and the differences in waste acceptance criteria quantified. In the third stage of modeling, precipitation/dissolution reactions were considered on the release and transport of the contaminants, and the subsequent impact on the maximum contaminant loading. The reactive transport modeling is considered a demonstration of the reactive transport capability, and shows the importance of its use for future performance predictions once site-specific data have been obtained.

  10. Defining waste acceptance criteria for the Hanford Replacement Cross-Site Transfer System

    International Nuclear Information System (INIS)

    Hudson, J.D.

    1996-04-01

    This document provides a methodology for defining waste acceptance criteria for the Hanford Replacement Cross-Site Transfer System (RCSTS). This methodology includes characterization, transport analysis, and control. A framework is described for each of these functions. A tool was developed for performing the calculations associated with the transport analysis. This tool, a worksheet that is available in formats acceptable for a variety of PC spreadsheet programs, enables a comparison of the pressure required to transport a given slurry at a rate that particulate suspension is maintained to the pressure drop available from the RCSTS

  11. Performance-based ECCS cladding acceptance criteria: A new simulation approach

    International Nuclear Information System (INIS)

    Zoino, A.; Alfonsi, A.; Rabiti, C.; Szilard, R.H.; Giannetti, F.; Caruso, G.

    2017-01-01

    Highlights: • A new methodology to demonstrate compliance with the new ECCS acceptance criteria is described. • A wide spectrum of fuel rod initial burnup states can be analysed in the design phase. • The coupled suite PHISICS/RELAP5-3D has been used in the analyses. • A demo simulation of the equilibrium cycle, load-following and a LOCA analysis has been performed. - Abstract: The U.S. Nuclear Regulatory Commission is currently proposing rulemaking to revise the Loss Of Coolant Accident (LOCA) and therefore the Emergency Core Cooling System (ECCS) acceptance criteria, to include the effects of higher burnup on cladding performance as well as to address other technical issues. As motivated by the new rule, the need to use advanced cladding designs may be a result. A loss of operational margin may result due to the more restrictive cladding embrittlement criteria. Initial and future compliance with the rule may significantly increase vendor workload and licensee cost, as a spectrum of fuel rod initial burnup states may need to be analyzed to demonstrate compliance. Consequently, there will be an increased focus on licensee decision making related to LOCA analysis to minimize cost and impact, and to manage margin. The study here presented has been part of a big project used to investigate technical issues and approaches for future industrial applications within the Risk-Informed Safety Margin Characterization (RISMC) Pathway. Specifically, the primary aim of this study is to lay out a roadmap to demonstrate the application of the new methodology. The present analysis shows a simplified version of the methodology of an industrial application on the Core Design and the Multi-Cycle Analysis.

  12. Preparation of acceptance tests and criteria for the Test Blanket Systems to be operated in ITER

    Energy Technology Data Exchange (ETDEWEB)

    Laan, J.G. van der, E-mail: JaapG.vanderLaan@iter.org [ITER Organization, Route de Vinon sur Verdon, CS 90 046, 13067 St Paul Lez Durance Cedex (France); Cuquel, B. [AIRBUS Defence and Space S.A.S., 13115 Saint Paul Lez Durance (France); Demange, D.; Ghidersa, B.-E. [Karlsruhe Institute of Technology, Karlsruhe (Germany); Giancarli, L.M.; Iseli, M.; Jourdan, T. [ITER Organization, Route de Vinon sur Verdon, CS 90 046, 13067 St Paul Lez Durance Cedex (France); Nevière, J.-C. [Comex-Nucleaire, 13115 Saint Paul Lez Durance (France); Pascal, R.; Ring, W. [ITER Organization, Route de Vinon sur Verdon, CS 90 046, 13067 St Paul Lez Durance Cedex (France)

    2015-10-15

    Highlights: • Initial guideline for acceptance testing and acceptance criteria for Test Blanket Systems in ITER. • These tests complement those required by the applicable codes and standards, and regulations. • Completion of TBS manufacture will be followed by Factory Acceptance Testing, prior to shipment. • Next steps are “Reception Inspection Tests”, and on-site pre-installation and components tests. • This guideline allows the detailing of the TBS specific test plans and their scheduling. - Abstract: This paper describes the main acceptance criteria and required acceptance tests for the components of the six Test Blanket Systems to be installed and operated in ITER. It summarizes the guide-line toward the establishment of detailed test plans for the TBS, starting from the end-product at the ITER Members factories, and to generally define the type of tests that have to be performed on the ITER site after shipment, and/or prior to the systems final commissioning phase.

  13. Basic considerations for the preparation of performance testing materials as related to performance evaluation acceptance criteria

    International Nuclear Information System (INIS)

    McCurdy, D.E.; Morton, J.S.

    2001-01-01

    The preparation of performance testing (PT) materials for environmental and radiobioassay applications involves the use of natural matrix materials containing the analyte of interest, the addition (spiking) of the analyte to a desired matrix (followed by blending for certain matrices) or a combination of the two. The distribution of the sample analyte concentration in a batch of PT samples will reflect the degree of heterogeneity of the analyte in the PT material and/or the reproducibility of the sample preparation process. Commercial and government implemented radioanalytical performance evaluation programs have a variety of acceptable performance criteria. The performance criteria should take into consideration many parameters related to the preparation of the PT materials including the within and between sample analyte heterogeneity, the accuracy of the quantification of an analyte in the PT material and to what 'known' value will a laboratory's result be compared. How sample preparation parameters affect the successful participation in performance evaluation (PE) programs having an acceptance criteria established as a percent difference from a 'known' value or in PE programs using other acceptance criteria, such as the guidance provided in ANSI N42.22 and N13.30 is discussed. (author)

  14. Acceptance criteria for determining armed response force size at nuclear power plants

    International Nuclear Information System (INIS)

    1983-02-01

    This guidance document contains acceptance criteria to be used in the NRC license review process. It consists of a scored worksheet and guidelines for interpreting the worksheet score that can be used in determining the adequacy of the armed response force size at a nuclear power reactor facility

  15. 48 CFR 15.607 - Criteria for acceptance and negotiation of an unsolicited proposal.

    Science.gov (United States)

    2010-10-01

    ... and negotiation of an unsolicited proposal. 15.607 Section 15.607 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION CONTRACTING METHODS AND CONTRACT TYPES CONTRACTING BY NEGOTIATION Unsolicited Proposals 15.607 Criteria for acceptance and negotiation of an unsolicited proposal. (a) A...

  16. Acceptance criteria for the low enriched uranium reform amendments

    International Nuclear Information System (INIS)

    Emeigh, C.W.; Gundersen, G.E.; Withee, C.J.

    1984-05-01

    Revisions have been made to the material control and accounting requirements for NRC licensees authorized to possess and use more than one effective kilogram of special nuclear material of low strategic significance to have material control and accounting systems able to (1) confirm the presence of special nuclear material, (2) resolve indications of missing material, and (3) aid in the investigation and recovery of missing material. This document presents criteria that can be used to aid in judging the acceptability of licensee plans that would be submitted to the NRC for implementing these capabilities. General performance objectives, system capabilities, and recordkeeping are addressed

  17. Contact-Handled Transuranic Waste Acceptance Criteria for the Waste Isolation Pilot Plant

    International Nuclear Information System (INIS)

    2005-01-01

    The purpose of this document is to summarize the waste acceptance criteria applicable to the transportation, storage, and disposal of contact-handled transuranic (CH-TRU) waste at the Waste Isolation Pilot Plant (WIPP). These criteria serve as the U.S. Department of Energy's (DOE) primary directive for ensuring that CH-TRU waste is managed and disposed of in a manner that protects human health and safety and the environment.The authorization basis of WIPP for the disposal of CH-TRU waste includes the U.S.Department of Energy National Security and Military Applications of Nuclear EnergyAuthorization Act of 1980 (reference 1) and the WIPP Land Withdrawal Act (LWA;reference 2). Included in this document are the requirements and associated criteriaimposed by these acts and the Resource Conservation and Recovery Act (RCRA,reference 3), as amended, on the CH-TRU waste destined for disposal at WIPP.|The DOE TRU waste sites must certify CH-TRU waste payload containers to thecontact-handled waste acceptance criteria (CH-WAC) identified in this document. Asshown in figure 1.0, the flow-down of applicable requirements to the CH-WAC istraceable to several higher-tier documents, including the WIPP operational safetyrequirements derived from the WIPP CH Documented Safety Analysis (CH-DSA;reference 4), the transportation requirements for CH-TRU wastes derived from theTransuranic Package Transporter-Model II (TRUPACT-II) and HalfPACT Certificates ofCompliance (references 5 and 5a), the WIPP LWA (reference 2), the WIPP HazardousWaste Facility Permit (reference 6), and the U.S. Environmental Protection Agency(EPA) Compliance Certification Decision and approval for PCB disposal (references 7,34, 35, 36, and 37). The solid arrows shown in figure 1.0 represent the flow-down of allapplicable payload container-based requirements. The two dotted arrows shown infigure 1.0 represent the flow-down of summary level requirements only; i.e., the sitesmust reference the regulatory source

  18. Contact-Handled Transuranic Waste Acceptance Criteria for the Waste Isolation Pilot Plant

    Energy Technology Data Exchange (ETDEWEB)

    Washington TRU Solutions LLC

    2005-12-29

    The purpose of this document is to summarize the waste acceptance criteria applicable to the transportation, storage, and disposal of contact-handled transuranic (CH-TRU) waste at the Waste Isolation Pilot Plant (WIPP). These criteria serve as the U.S. Department of Energy's (DOE) primary directive for ensuring that CH-TRU waste is managed and disposed of in a manner that protects human health and safety and the environment.The authorization basis of WIPP for the disposal of CH-TRU waste includes the U.S.Department of Energy National Security and Military Applications of Nuclear EnergyAuthorization Act of 1980 (reference 1) and the WIPP Land Withdrawal Act (LWA;reference 2). Included in this document are the requirements and associated criteriaimposed by these acts and the Resource Conservation and Recovery Act (RCRA,reference 3), as amended, on the CH-TRU waste destined for disposal at WIPP.|The DOE TRU waste sites must certify CH-TRU waste payload containers to thecontact-handled waste acceptance criteria (CH-WAC) identified in this document. Asshown in figure 1.0, the flow-down of applicable requirements to the CH-WAC istraceable to several higher-tier documents, including the WIPP operational safetyrequirements derived from the WIPP CH Documented Safety Analysis (CH-DSA;reference 4), the transportation requirements for CH-TRU wastes derived from theTransuranic Package Transporter-Model II (TRUPACT-II) and HalfPACT Certificates ofCompliance (references 5 and 5a), the WIPP LWA (reference 2), the WIPP HazardousWaste Facility Permit (reference 6), and the U.S. Environmental Protection Agency(EPA) Compliance Certification Decision and approval for PCB disposal (references 7,34, 35, 36, and 37). The solid arrows shown in figure 1.0 represent the flow-down of allapplicable payload container-based requirements. The two dotted arrows shown infigure 1.0 represent the flow-down of summary level requirements only; i.e., the sitesmust reference the regulatory source

  19. The revision of RP 91 on criteria for acceptability of radiological (including radiotherapy) and nuclear medicine installations

    International Nuclear Information System (INIS)

    Faulkner, K.; Malone, J. F.; Christofides, S.; Lillicrap, S.; Horton, P.

    2013-01-01

    In 1997 the European Commission published Radiation Protection 91: 'Criteria for acceptability of radiological (including radiotherapy) and nuclear medicine installations'(1). This document specified the minimum criteria for acceptability. It has been used to this effect in legislation, codes of practice and by individual professionals. In a single document, it defined a level of performance at which remedial action was required. The document specified a series of parameters which characterised equipment performance and acceptable levels of performance. In its time it proved to be a useful document which was applied in member states to various degrees. Since the publication of Report 91 in 1997(1), a series of weaknesses emerged over time. Development of new radiological systems and technologies, as well as improvements in traditional technologies, has created circumstances where the acceptability criteria were in need of review. These weaknesses were recognised by the European Commission and a tender for its revision was issued. The criteria were developed by a team drawn from a broad range of backgrounds including hospitals, industry, government bodies, regulators and standardisation organisations. Representatives were mainly from Europe, but individuals from the American Association of Physicists in Medicine and International Atomic Energy Agency were included in the drafting process. This study describes the process employed in developing the revised document and the consultation process involved. One of the major difficulties the revision team encountered was related to an understanding of the actual meaning of the EC Directive(2). The view taken by the revision team was that Article 8, paragraph 3 places responsibilities on both the holders of radiological equipment and competent authorities. The acceptability criteria have been produced consistent with the European Commission's Medical Exposures Directive(2), which requires that patient exposures are

  20. 48 CFR 915.607 - Criteria for acceptance and negotiation of an unsolicited proposal.

    Science.gov (United States)

    2010-10-01

    ... and negotiation of an unsolicited proposal. 915.607 Section 915.607 Federal Acquisition Regulations System DEPARTMENT OF ENERGY CONTRACTING METHODS AND CONTRACT TYPES CONTRACTING BY NEGOTIATION Unsolicited Proposals 915.607 Criteria for acceptance and negotiation of an unsolicited proposal. (c) DOE's cost...

  1. Development of performance assessment methodology for establishment of quantitative acceptance criteria of near-surface radioactive waste disposal

    Energy Technology Data Exchange (ETDEWEB)

    Kim, C. R.; Lee, E. Y.; Park, J. W.; Chang, G. M.; Park, H. Y.; Yeom, Y. S. [Korea Hydro and Nuclear Power Co., Ltd., Seoul (Korea, Republic of)

    2002-03-15

    The contents and the scope of this study are as follows : review of state-of-the-art on the establishment of waste acceptance criteria in foreign near-surface radioactive waste disposal facilities, investigation of radiological assessment methodologies and scenarios, investigation of existing models and computer codes used in performance/safety assessment, development of a performance assessment methodology(draft) to derive quantitatively radionuclide acceptance criteria of domestic near-surface disposal facility, preliminary performance/safety assessment in accordance with the developed methodology.

  2. Safety analysis, risk assessment, and risk acceptance criteria

    International Nuclear Information System (INIS)

    Jamali, K.

    1997-01-01

    This paper discusses a number of topics that relate safety analysis as documented in the Department of Energy (DOE) safety analysis reports (SARs), probabilistic risk assessments (PRA) as characterized primarily in the context of the techniques that have assumed some level of formality in commercial nuclear power plant applications, and risk acceptance criteria as an outgrowth of PRA applications. DOE SARs of interest are those that are prepared for DOE facilities under DOE Order 5480.23 and the implementing guidance in DOE STD-3009-94. It must be noted that the primary area of application for DOE STD-3009 is existing DOE facilities and that certain modifications of the STD-3009 approach are necessary in SARs for new facilities. Moreover, it is the hazard analysis (HA) and accident analysis (AA) portions of these SARs that are relevant to the present discussions. Although PRAs can be qualitative in nature, PRA as used in this paper refers more generally to all quantitative risk assessments and their underlying methods. HA as used in this paper refers more generally to all qualitative risk assessments and their underlying methods that have been in use in hazardous facilities other than nuclear power plants. This discussion includes both quantitative and qualitative risk assessment methods. PRA has been used, improved, developed, and refined since the Reactor Safety Study (WASH-1400) was published in 1975 by the Nuclear Regulatory Commission (NRC). Much debate has ensued since WASH-1400 on exactly what the role of PRA should be in plant design, reactor licensing, 'ensuring' plant and process safety, and a large number of other decisions that must be made for potentially hazardous activities. Of particular interest in this area is whether the risks quantified using PRA should be compared with numerical risk acceptance criteria (RACs) to determine whether a facility is 'safe.' Use of RACs requires quantitative estimates of consequence frequency and magnitude

  3. Final report on a study of coherence in acceptability criteria for the technical aspects of risks associated with potentially hazardous installations

    International Nuclear Information System (INIS)

    Chicken, J.C.

    1988-01-01

    This report describes the results of the study that was made, under Contract No ECI-1390-B7221-85D, for the European Atomic Energy Community. The aim of the study was to examine and assess the feasibility of developing coherent and uniform criteria for judging the acceptability of the technical aspects of the risks associated with potentially hazardous installations. The report is arranged in five main parts. First the nature of hazardous installations is considered and this provides the basis for examination of the currently-used technical risk acceptability criteria. Next, the possible forms of criteria are explored and then universally consistent partial and overall technical risk acceptability criteria are proposed. Following this the implications of using the criteria proposed at the design, regulatory and operating levels are examined. Then, by testing the criteria against some real decisions, the practical problems of using the proposed criteria are explored. This leads to consideration of possible alternatives to the proposed criteria. Finally the conclusions that appear to be justified are summarized and the need for further work is identified

  4. Qualifications of and acceptance criteria for transporting special form radioactive material

    International Nuclear Information System (INIS)

    Hovingh, J.

    1991-01-01

    A special form radioactive material is a radioactive material that is in an inert, insoluble, indispersible form such that even in the event of an accident, it will not be dispersed into the environment in a way that could have an adverse impact on public health and safety. Methods of qualifying a special form radioactive material are discussed. Interpretation of acceptance criteria are proposed for the transportation of Type B quantities of a special form radioactive material. 11 refs

  5. 10 CFR 50.46a - Acceptance criteria for reactor coolant system venting systems.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 1 2010-01-01 2010-01-01 false Acceptance criteria for reactor coolant system venting systems. 50.46a Section 50.46a Energy NUCLEAR REGULATORY COMMISSION DOMESTIC LICENSING OF PRODUCTION AND... function of these systems. High point vents are not required for the tubes in U-tube steam generators...

  6. Acceptability criteria for linear dependence in validating UV-spectrophotometric methods of quantitative determination in forensic and toxicological analysis

    Directory of Open Access Journals (Sweden)

    L. Yu. Klimenko

    2014-08-01

    Full Text Available Introduction. This article is the result of authors’ research in the field of development of the approaches to validation of quantitative determination methods for purposes of forensic and toxicological analysis and devoted to the problem of acceptability criteria formation for validation parameter «linearity/calibration model». The aim of research. The purpose of this paper is to analyse the present approaches to acceptability estimation of the calibration model chosen for method description according to the requirements of the international guidances, to form the own approaches to acceptability estimation of the linear dependence when carrying out the validation of UV-spectrophotometric methods of quantitative determination for forensic and toxicological analysis. Materials and methods. UV-spectrophotometric method of doxylamine quantitative determination in blood. Results. The approaches to acceptability estimation of calibration models when carrying out the validation of bioanalytical methods is stated in international papers, namely «Guidance for Industry: Bioanalytical method validation» (U.S. FDA, 2001, «Standard Practices for Method Validation in Forensic Toxicology» (SWGTOX, 2012, «Guidance for the Validation of Analytical Methodology and Calibration of Equipment used for Testing of Illicit Drugs in Seized Materials and Biological Specimens» (UNODC, 2009 and «Guideline on validation of bioanalytical methods» (ЕМА, 2011 have been analysed. It has been suggested to be guided by domestic developments in the field of validation of analysis methods for medicines and, particularly, by the approaches to validation methods in the variant of the calibration curve method for forming the acceptability criteria of the obtained linear dependences when carrying out the validation of UV-spectrophotometric methods of quantitative determination for forensic and toxicological analysis. The choice of the method of calibration curve is

  7. An approach to societal risk acceptance criteria and risk management

    International Nuclear Information System (INIS)

    Okrent, D.; Whipple, C.

    1977-06-01

    A quantitative approach to risk acceptance criteria and risk management is proposed for activities involving risk to individuals not receiving direct benefits, such as employment, from the activity. Societal activities are divided into major facilities or technologies, all or part of which are categorized as essential, beneficial, or peripheral, and a decreasing level of acceptable risk to the most exposed individual is proposed (say, 0.0002/year for essential, 0.00001/year for beneficial, and 0.000002/year for peripheral activity). The risk would be assessed at a high confidence level (say, 90%), thereby providing an incentive to the gaining of better knowledge. Each risk-producing facility, technology, etc., would have to undergo assessment both of risk to the individual and to society. The cost of the latter would have to be internalized, probably via a tax paid to the Federal Government, which in turn would redistribute the benefit as national health insurance or reduced taxes to the individual. Risk aversion to large events would be built into the internalization of the cost of risk

  8. Methods for verifying compliance with low-level radioactive waste acceptance criteria

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-09-01

    This report summarizes the methods that are currently employed and those that can be used to verify compliance with low-level radioactive waste (LLW) disposal facility waste acceptance criteria (WAC). This report presents the applicable regulations representing the Federal, State, and site-specific criteria for accepting LLW. Typical LLW generators are summarized, along with descriptions of their waste streams and final waste forms. General procedures and methods used by the LLW generators to verify compliance with the disposal facility WAC are presented. The report was written to provide an understanding of how a regulator could verify compliance with a LLW disposal facility`s WAC. A comprehensive study of the methodology used to verify waste generator compliance with the disposal facility WAC is presented in this report. The study involved compiling the relevant regulations to define the WAC, reviewing regulatory agency inspection programs, and summarizing waste verification technology and equipment. The results of the study indicate that waste generators conduct verification programs that include packaging, classification, characterization, and stabilization elements. The current LLW disposal facilities perform waste verification steps on incoming shipments. A model inspection and verification program, which includes an emphasis on the generator`s waste application documentation of their waste verification program, is recommended. The disposal facility verification procedures primarily involve the use of portable radiological survey instrumentation. The actual verification of generator compliance to the LLW disposal facility WAC is performed through a combination of incoming shipment checks and generator site audits.

  9. Methods for verifying compliance with low-level radioactive waste acceptance criteria

    International Nuclear Information System (INIS)

    1993-09-01

    This report summarizes the methods that are currently employed and those that can be used to verify compliance with low-level radioactive waste (LLW) disposal facility waste acceptance criteria (WAC). This report presents the applicable regulations representing the Federal, State, and site-specific criteria for accepting LLW. Typical LLW generators are summarized, along with descriptions of their waste streams and final waste forms. General procedures and methods used by the LLW generators to verify compliance with the disposal facility WAC are presented. The report was written to provide an understanding of how a regulator could verify compliance with a LLW disposal facility's WAC. A comprehensive study of the methodology used to verify waste generator compliance with the disposal facility WAC is presented in this report. The study involved compiling the relevant regulations to define the WAC, reviewing regulatory agency inspection programs, and summarizing waste verification technology and equipment. The results of the study indicate that waste generators conduct verification programs that include packaging, classification, characterization, and stabilization elements. The current LLW disposal facilities perform waste verification steps on incoming shipments. A model inspection and verification program, which includes an emphasis on the generator's waste application documentation of their waste verification program, is recommended. The disposal facility verification procedures primarily involve the use of portable radiological survey instrumentation. The actual verification of generator compliance to the LLW disposal facility WAC is performed through a combination of incoming shipment checks and generator site audits

  10. Small bore pipe acceptance criteria for watts bar nuclear plant Tennessee Valley Authority

    International Nuclear Information System (INIS)

    Sun, W.S.; Lee, R.L.; Kalyanan, N.

    1991-01-01

    Small bore pipe (≤2 inches NPS) is traditionally analyzed by simplified techniques using Cook Book approach, which yield conservative results. However, reconciliation of these systems for as-built condition where the original criteria is observed to have been exceeded (or due to additions etc.) generally becomes a time consuming and expensive operation since a rigorous computer aided analysis or a detailed hand calculation becomes necessary. The acceptance criteria in this paper can be effectively used in such cases. The approach involves utilizing basic engineering principles and plant specific parameters (such as earthquake spectra) to estimate the system response such as pipe stress due to various loading conditions, piping frequency, support and anchor loads, valve acceleration etc

  11. Long-Term Safety Analysis of Baldone Radioactive Waste Repository and Updating of Waste Acceptance Criteria

    International Nuclear Information System (INIS)

    2001-12-01

    The main objective of the project was to provide advice to the Latvian authorities on the safety enhancements and waste acceptance criteria for near surface radioactive waste disposal facilities of the Baldone repository. The project included the following main activities: Analysis of the current status of the management of radioactive waste in Latvia in general and, at the Baldone repository in particular Development of the short and long-term safety analysis of the Baldone repository, including: the planned increasing of capacity for disposal and long term storage, the radiological analysis for the post-closure period Development of the Environment Impact Statement, for the new foreseen installations, considering the non radiological components Proposal of recommendations for future updating of radioactive waste acceptance criteria Proposal of recommendations for safety upgrades to the facility. The work programme has been developed in phases and main tasks as follows. Phase 0: Project inception, Phase 1: Establishment of current status, plans and practices (Legislation, regulation and standards, Radioactive waste management, Waste acceptance criteria), Phase 2: Development of future strategies for long-term safety management and recommendations for safety enhancements. The project team found the general approach use at the installation, the basic design and the operating practices appropriate to international standards. Nevertheless, a number of items subject to potential improvements were also identified. These upgrading recommendations deal with general aspects of the management (mainly storage versus disposal of long-lived sources), site and environmental surveillance, packaging (qualification of containers, waste characterization requirements), the design of an engineered cap and strategies for capping. (author)

  12. Expanded criteria donor kidneys for younger recipients: acceptable outcomes.

    Science.gov (United States)

    Goplani, K R; Kute, V B; Vanikar, A V; Shah, P R; Gumber, M R; Patel, H V; Modi, P R; Trivedi, H L

    2010-12-01

    European senior programme (ESP) is well known for acceptable outcomes using expanded criteria donor (ECD) kidneys from donors older than 65 years for recipients older than 65 years. The incidence of end-stage renal disease (ESRD) is 229/million in India with a mean age of 45 years. We performed a retrospective analysis of transplantation of ECD versus standard criteria donor (SCD) kidneys into younger recipients. Forty-three ECD transplantations among 158 deceased donor organ transplantation (DDOT) were performed between January 2006 and December 2009. Among 43 transplantation from 30 donors, 14 were dual kidney transplantations (DKT) performed based upon biopsy evaluation. All recipients received thymoglobulin (rATG) induction followed by immunosuppression with a steroid, mycophenolate mofetil (MMF), and a calcineurin inhibitor. Statistical analysis used chi-square test and unpaired Student t test. Kaplan-Meier curves were used for survival analysis. For ECD the mean donor age was 64 ± 11 years. Cerebrovascular accidents (CVA) were the cause of death among 60% of donors, 73.13% of whom were hypertensive and 23.13% diabetic. Mean DKT donor age was 75 ± 9.17 years versus 60 ± 8.0 years for single kidney transplantation (SKT). Mean recipient age of DKT versus SKT was 44 ± 12.4 years versus 43 ± 14 years. Mean serum creatinine (SCr; mg/dL) of SKT patients was 1.64 ± 0.75 versus 1.68 ± 0.46 in DKT. Mean follow-up was 455 ± 352 days. Mean SCr of 43 ECD recipients of mean age, 43.4 ± 14.2 years was 1.61 ± 0.61 mg/dL. Among 43 recipients, 23.25% were diabetic, 41.86% displayed delayed graft function (DGF), and 23.25% experienced biopsy-proven acute rejection (BPAR). Patient survival rate was 72.09% and graft survival rate was 67.44%. For SCD transplantations (n = 115), the mean donor age was 36 ± 14 years and recipient mean age was 32.8 ± 14.07 years. Mean SCr was 1.32 ± 0.46 mg/dL with 26.95% recipients displaying DGF, whereas 20.86% had BPAR. In the SCD

  13. Study of waste acceptance criteria for low-level radioactive waste from medical, industrial, and research facilities (Contract research)

    International Nuclear Information System (INIS)

    Koibuchi, Hiroto; Dohi, Terumi; Ishiguro, Hideharu; Hayashi, Masaru; Senda, Masaki

    2008-12-01

    Japan Atomic Energy Agency (JAEA) is supposed to draw up the plan for the disposal program of the very low-level radioactive waste and low-level radioactive waste generated from medical, industrial and research facilities. For instance, there are these facilities in JAEA, universities, private companies, and so on. JAEA has to get to know about the waste and its acceptance of other institutions described above because it is important for us to hold the licenses for the disposal program regarding safety assessment. This report presents the basic data concerning radioactive waste of research institutes etc. except RI waste, domestic and foreign information related to acceptance criteria for disposal of the low-level radioactive waste, the current status of foreign medical waste management, waste acceptance, and such. In this report, Japan's acceptance criteria were summarized on the basis of present regulation. And, the criteria of foreign countries, United States, France, United Kingdom and Spain, were investigated by survey of each reference. In addition, it was reported that the amount of waste from laboratories etc. for near-surface disposal and their characterization in our country. The Subjects of future work: the treatment of hazardous waste, the problem of the double-regulation (the Nuclear Reactor Regulation Law and the Law Concerning Prevention from Radiation Hazards due to Radioisotopes and Others) and the possession of waste were discussed here. (author)

  14. Acceptance criteria for the low enriched uranium reform amendments. Revision 1

    International Nuclear Information System (INIS)

    Emeigh, C.W.; Gundersen, G.E.; Withee, C.J.

    1985-04-01

    Revisions have been made to the material control and accounting requirements for NRC licensees authorized to possess and use more than one effective kilogram of special nuclear material of low strategic significance to have MC and A systems able to (1) confirm the presence of special nuclear material, (2) resolve indications of missing material, and (3) aid in the investigation and recovery of missing material. This document presents criteria that can be used to aid in judging the acceptability of licensee plans that would be submitted to the NRC for implementing these capabilities. General performance objectives, system capabilities, and recordkeeping are addressed

  15. Preliminary Mark-18A (Mk-18A) Target Material Recovery Program Product Acceptance Criteria

    Energy Technology Data Exchange (ETDEWEB)

    Robinson, Sharon M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Patton, Bradley D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2016-09-01

    The Mk-18A Target Material Recovery Program (MTMRP) was established in 2015 to preserve the unique materials, e.g. 244Pu, in 65 previously irradiated Mk-18A targets for future use. This program utilizes existing capabilities at SRS and Savannah River National Laboratory (SRNL) to process targets, recover materials from them, and to package the recovered materials for shipping to ORNL. It also utilizes existing capabilities at ORNL to receive and store the recovered materials, and to provide any additional processing of the recovered materials or residuals required to prepare them for future beneficial use. The MTMRP is presently preparing for the processing of these valuable targets which is expected to begin in ~2019. As part of the preparations for operations, this report documents the preliminary acceptance criteria for the plutonium and heavy curium materials to be recovered from the Mk-18A targets at SRNL for transport and storage at ORNL. These acceptance criteria were developed based on preliminary concepts developed for processing, transporting, and storing the recovered Mk-18A materials. They will need to be refined as these concepts are developed in more detail.

  16. Preliminary Mark-18A (Mk-18A) Target Material Recovery Program Product Acceptance Criteria

    International Nuclear Information System (INIS)

    Robinson, Sharon M.; Patton, Bradley D.

    2016-01-01

    The Mk-18A Target Material Recovery Program (MTMRP) was established in 2015 to preserve the unique materials, e.g. 244 Pu, in 65 previously irradiated Mk-18A targets for future use. This program utilizes existing capabilities at SRS and Savannah River National Laboratory (SRNL) to process targets, recover materials from them, and to package the recovered materials for shipping to ORNL. It also utilizes existing capabilities at ORNL to receive and store the recovered materials, and to provide any additional processing of the recovered materials or residuals required to prepare them for future beneficial use. The MTMRP is presently preparing for the processing of these valuable targets which is expected to begin in ~2019. As part of the preparations for operations, this report documents the preliminary acceptance criteria for the plutonium and heavy curium materials to be recovered from the Mk-18A targets at SRNL for transport and storage at ORNL. These acceptance criteria were developed based on preliminary concepts developed for processing, transporting, and storing the recovered Mk-18A materials. They will need to be refined as these concepts are developed in more detail.

  17. CTOD-based acceptance criteria for heat exchanger head staybolts

    International Nuclear Information System (INIS)

    Lam, P.S.; Sindelar, R.L.; Barnes, D.M.; Awadalla, N.G.

    1992-01-01

    The primary coolant piping system of the Savannah River Site (SRS) reactors contains twelve heat exchangers to remove the waste heat from the nuclear materials production. A large break at the inlet or outlet heads of the heat exchangers would occur if the restraint members of the heads become inactive. The heat exchanger head is attached to the tubesheet by 84 staybolts. The structural integrity of the heads is demonstrated by showing the redundant capacity of the staybolts to restrain the head at design conditions and under seismic loadings. The beat exchanger head is analyzed with a three- dimensional finite element model. The restraint provided by the staybolts is evaluated for several postulated cases of inactive or missing staybolts, that is, bolts that have a flaw exceeding the ultrasonic testing (UT) threshold depth of 25% of the bolt diameter. A limit of 6 inactive staybolts is reached with a fracture criterion based on the maximum allowable local displacement at the active staybolts which corresponds to the crack tip opening displacement (CTOD) of 0.032 inches. An acceptance criteria methodology has been developed to disposition flaws reported in the staybolt inspections while ensuring adequate restraint capacity of the staybolts to maintain integrity of the heat exchanger heads against collapse. The methodology includes an approach for the baseline and periodic inspections of the staybolts. A total of up to 6 staybolts, reported as containing flaws with depths at or exceeding 25% would be acceptable in the heat exchanger

  18. Structural acceptance criteria for the evaulation of existing double-shell waste storage tanks located at the Hanford site, Richland, Washington

    International Nuclear Information System (INIS)

    Julyk, L.J.; Day, A.D.; Dyrness, A.D.; Moore, C.J.; Peterson, W.S.; Scott, M.A.; Shrivastava, H.P.; Sholman, J.S.; Watts, T.N.

    1995-09-01

    The structural acceptance criteria contained herein for the evaluation of existing underground double-shell waste storage tanks located at the Hanford Site is part of the Life Management/Aging Management Program of the Tank Waste Remediation System. The purpose of the overall life management program is to ensure that confinement of the waste is maintained over the required service life of the tanks. Characterization of the present condition of the tanks, understanding and characterization of potential degradation mechanisms, and development of tank structural acceptance criteria based on previous service and projected use are prerequisites to assessing tank integrity, to projecting the length of tank service, and to developing and applying prudent fixes or repairs. The criteria provided herein summarize the requirements for the analysis and structural qualification of the existing double-shell tanks for continued operation. Code reconciliation issues and material degradation under aging conditions are addressed. Although the criteria were developed for double-shell tanks, many of the provisions are equally applicable to single-shell tanks. However, the criteria do not apply to the evaluation of tank appurtenances and buried piping

  19. Acceptance criteria for disposal of radioactive waste in Romania

    International Nuclear Information System (INIS)

    Dogaru, D.

    2001-01-01

    In Romania the institutional radioactive waste are managed by National Institute of R and D for Physics and Nuclear Engineering. The institutional radioactive waste are collected, treated and conditioned at the Radioactive Waste Treatment Plant then transferred and disposed to the National Repository of Radioactive Waste at Baita Bihor. National Repository for Radioactive Waste is a long term storage facility. The repository is placed in a former worked out uranium ore mine, being excavated in the Bihor peak. The repository has been sited taking into account the known geological, hydrogeoloical, seismic and meteorological and mining properties of a uranium mining site. In the absence of an updated Safety Analysis Report, the maximum radioactive content permitted by the regulatory authority in the operation license is below the values reported for other engineered repositories in mine galleries. The paper presents the acceptance criteria for disposal of radioactive waste in National Repository for Radioactive Waste at Baita Bihor. (author)

  20. Determination of acceptable risk criteria for nuclear waste management

    International Nuclear Information System (INIS)

    Cohen, J.J.

    1977-01-01

    The initial phase of the work performed during FY 1977 consisted of performing a ''scoping'' study to define issues, determine an optimal methodology for their resolution, and compile a data base for acceptable risk criteria development. The issues, spanning technical, psychological, and ethical dimensions, were categorized in seven major areas: (1) unplanned or accidental events, (2) present vs future risks, (3) institutional controls and retrievability, (4) dose-response mechanism and uncertainty, (5) spatial distribution of exposed populations, (6) different types of nuclear wastes, and (7) public perception. The optimum methodology for developing ARC was determined to be multi-attribute decision analysis encompassing numerous specific techniques for choosing, from among several alternatives, the optimal course of action when the alternatives are constrained to meet specified attributes. The data base developed during the study comprises existing regulations and guidelines, maximum permissible dose, natural geologic hazards, nonradioactive hazardous waste practices, bioethical perspectives, and data from an opinion survey

  1. Determination of acceptable risk criteria for nuclear waste management

    Energy Technology Data Exchange (ETDEWEB)

    Cohen, J.J.

    1977-10-21

    The initial phase of the work performed during FY 1977 consisted of performing a ''scoping'' study to define issues, determine an optimal methodology for their resolution, and compile a data base for acceptable risk criteria development. The issues, spanning technical, psychological, and ethical dimensions, were categorized in seven major areas: (1) unplanned or accidental events, (2) present vs future risks, (3) institutional controls and retrievability, (4) dose-response mechanism and uncertainty, (5) spatial distribution of exposed populations, (6) different types of nuclear wastes, and (7) public perception. The optimum methodology for developing ARC was determined to be multi-attribute decision analysis encompassing numerous specific techniques for choosing, from among several alternatives, the optimal course of action when the alternatives are constrained to meet specified attributes. The data base developed during the study comprises existing regulations and guidelines, maximum permissible dose, natural geologic hazards, nonradioactive hazardous waste practices, bioethical perspectives, and data from an opinion survey.

  2. Criteria of acceptability relating to the approval of consumer goods containing radioactive substances

    International Nuclear Information System (INIS)

    Paynter, R.A.

    1992-01-01

    The criteria are described which the Board intends to use when considering goods containing radioactive substances for approval under the regulations that the Government intends to make with respect to such goods. Some products are deemed unacceptable in principle because there would appear to be no justification for the use of radioactive substances in them. Examples of such products are given. Other products may be approved for supply to the public depending on the doses likely to be received by individuals, principally those who use the products. A lower dose is considered acceptable from products that do not contribute to safety than from products that do. In the interim, before the regulations are made, the criteria will be used as the basis of the Board's advice to suppliers and manufacturers of goods containing radioactive substances. (Author)

  3. The APS thin pulsed septum magnets

    International Nuclear Information System (INIS)

    Lopez, F.; Mills, F.; Milton, S.; Reeves, S.; Sheynin, S.; Thompson, K.; Turner, L.

    1994-01-01

    A thin (2-mm) eddy-current pulsed septum magnet was developed for use in the Advanced Photon Source (APS) machines. A number of different configurations of the magnet were assembled and tested in an effort to minimize the undesired leakage field in the stored-beam region. However, because of measured excessive leakage fields, an alternative direct-drive septum magnet was also constructed and tested. We present here the design specifications and acceptable performance criteria along with results of magnetic field measurements

  4. Evaluation of ISDP Batch 2 Qualification Compliance to 512-S, DWPF, Tank Farm, and Saltstone Waste Acceptance Criteria

    Energy Technology Data Exchange (ETDEWEB)

    Shafer, A.

    2010-05-05

    The purpose of this report is to document the acceptability of the second macrobatch (Salt Batch 2) of Tank 49H waste to H Tank Farm, DWPF, and Saltstone for operation of the Interim Salt Disposition Project (ISDP). Tank 49 feed meets the Waste Acceptance Criteria (WAC) requirements specified by References 11, 12, and 13. Salt Batch 2 material is qualified and ready to be processed through ARP/MCU to the final disposal facilities.

  5. Advances in flaw evaluation procedures and acceptance criteria for reactor piping

    International Nuclear Information System (INIS)

    Gamble, R.M.; Zahoor, A.; Norris, D.M.

    1986-01-01

    During the past several years, intergranular stress corrosion cracks (IGSCC) have been detected in stainless steel piping in boiling water reactors (BWRs) and have resulted in an increased number of flaw evaluations. To reduce the outage time associated with evaluating IGSCC, various research and ASME code groups have spent significant effort to provide utility personnel with efficient means to detect, classify, and size flaws, and to determine suitability for return to service for flawed stainless steel piping. One of the several nondestructive evaluation technologies that has received considerable attention is fracture mechanics, the discipline that considers the failure of flawed material. Fracture mechanics can be used to answer two key questions concerning return to service of flawed pipe: (a) what is the largest flaw size that can be returned to service and still maintain adequate safety margins at the applied loads, and (b) how much operating time remains before the crack reaches the largest allowable size? The purpose of this paper is to provide an overview of the recently developed ASME code Section XI flaw size evaluation procedure and acceptance criteria for stainless steel piping and their application by BWR owners to efficiently determine if flaws found by nondestructive examination are acceptable for continued service

  6. Advances in flaw evaluation procedures and acceptance criteria for reactor piping

    Energy Technology Data Exchange (ETDEWEB)

    Gamble, R.M.; Zahoor, A.; Norris, D.M.

    1986-01-01

    During the past several years, intergranular stress corrosion cracks (IGSCC) have been detected in stainless steel piping in boiling water reactors (BWRs) and have resulted in an increased number of flaw evaluations. To reduce the outage time associated with evaluating IGSCC, various research and ASME code groups have spent significant effort to provide utility personnel with efficient means to detect, classify, and size flaws, and to determine suitability for return to service for flawed stainless steel piping. One of the several nondestructive evaluation technologies that has received considerable attention is fracture mechanics, the discipline that considers the failure of flawed material. Fracture mechanics can be used to answer two key questions concerning return to service of flawed pipe: (a) what is the largest flaw size that can be returned to service and still maintain adequate safety margins at the applied loads, and (b) how much operating time remains before the crack reaches the largest allowable size. The purpose of this paper is to provide an overview of the recently developed ASME code Section XI flaw size evaluation procedure and acceptance criteria for stainless steel piping and their application by BWR owners to efficiently determine if flaws found by nondestructive examination are acceptable for continued service.

  7. HOW TO DEAL WITH WASTE ACCEPTANCE UNCERTAINTY USING THE WASTE ACCEPTANCE CRITERIA FORECASTING AND ANALYSIS CAPABILITY SYSTEM (WACFACS)

    Energy Technology Data Exchange (ETDEWEB)

    Redus, K. S.; Hampshire, G. J.; Patterson, J. E.; Perkins, A. B.

    2002-02-25

    The Waste Acceptance Criteria Forecasting and Analysis Capability System (WACFACS) is used to plan for, evaluate, and control the supply of approximately 1.8 million yd3 of low-level radioactive, TSCA, and RCRA hazardous wastes from over 60 environmental restoration projects between FY02 through FY10 to the Oak Ridge Environmental Management Waste Management Facility (EMWMF). WACFACS is a validated decision support tool that propagates uncertainties inherent in site-related contaminant characterization data, disposition volumes during EMWMF operations, and project schedules to quantitatively determine the confidence that risk-based performance standards are met. Trade-offs in schedule, volumes of waste lots, and allowable concentrations of contaminants are performed to optimize project waste disposition, regulatory compliance, and disposal cell management.

  8. HOW TO DEAL WITH WASTE ACCEPTANCE UNCERTAINTY USING THE WASTE ACCEPTANCE CRITERIA FORECASTING AND ANALYSIS CAPABILITY SYSTEM (WACFACS)

    International Nuclear Information System (INIS)

    Redus, K. S.; Hampshire, G. J.; Patterson, J. E.; Perkins, A. B.

    2002-01-01

    The Waste Acceptance Criteria Forecasting and Analysis Capability System (WACFACS) is used to plan for, evaluate, and control the supply of approximately 1.8 million yd3 of low-level radioactive, TSCA, and RCRA hazardous wastes from over 60 environmental restoration projects between FY02 through FY10 to the Oak Ridge Environmental Management Waste Management Facility (EMWMF). WACFACS is a validated decision support tool that propagates uncertainties inherent in site-related contaminant characterization data, disposition volumes during EMWMF operations, and project schedules to quantitatively determine the confidence that risk-based performance standards are met. Trade-offs in schedule, volumes of waste lots, and allowable concentrations of contaminants are performed to optimize project waste disposition, regulatory compliance, and disposal cell management

  9. Thin-Slice Measurement of Wisdom

    Directory of Open Access Journals (Sweden)

    Chao S. Hu

    2017-08-01

    Full Text Available Objective Measurement of Wisdom within a short period of time is vital for both the public interest (e.g., understanding a presidential election and research (e.g., testing factors that facilitate wisdom development. A measurement of emotion associated with wisdom would be especially informative; therefore, a novel Thin-Slice measurement of wisdom was developed based on the Berlin Paradigm. For about 2 min, participants imagined the lens of a camera as the eyes of their friend/teacher whom they advised about a life dilemma. Verbal response and facial expression were both recorded by a camera: verbal responses were then rated on both the Berlin Wisdom criteria and newly developed Chinese wisdom criteria; facial expressions were analyzed by the software iMotion FACET module. Results showed acceptable inter-rater and inter-item reliability for this novel paradigm. Moreover, both wisdom ratings were not significantly correlated with Social desirability, and the Berlin wisdom rating was significantly negatively correlated with Neuroticism; feeling of surprise was significantly positively correlated with both wisdom criteria ratings. Our results provide the first evidence of this Thin-slice Wisdom Paradigm’s reliability, its immunity to social desirability, and its validity for assessing candidates’ wisdom within a short timeframe. Although still awaiting further development, this novel Paradigm contributes to an emerging Universal Wisdom Paradigm applicable across cultures.

  10. Nevada test site waste acceptance criteria

    International Nuclear Information System (INIS)

    1996-01-01

    This document provides the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive and mixed waste for disposal; and transuranic and transuranic mixed waste for interim storage at the NTS. Review each section of this document. This document is not intended to include all of the requirements; rather, it is meant as a guide toward meeting the regulations. All references in this document should be observed to avoid omission of requirements on which acceptance or rejection of waste will be based. The Department of Energy/Nevada Operations Office (DOE/NV) and support contractors are available to assist you in understanding or interpreting this document

  11. Nevada test site waste acceptance criteria

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-09-01

    This document provides the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive and mixed waste for disposal; and transuranic and transuranic mixed waste for interim storage at the NTS. Review each section of this document. This document is not intended to include all of the requirements; rather, it is meant as a guide toward meeting the regulations. All references in this document should be observed to avoid omission of requirements on which acceptance or rejection of waste will be based. The Department of Energy/Nevada Operations Office (DOE/NV) and support contractors are available to assist you in understanding or interpreting this document.

  12. Derivation of Waste Acceptance Criteria for Low and Intermediate Level Waste in Surface Disposal Facility

    International Nuclear Information System (INIS)

    Gagner, L.; Voinis, S.

    2000-01-01

    In France, low- and intermediate-level radioactive wastes are disposed in a near-surface facility, at Centre de l'Aube disposal facility. This facility, which was commissioned in 1992, has a disposal capacity of one million cubic meters, and will be operated up to about 2050. It took over the job from Centre de la Manche, which was commissioned in 1969 and shut down in 1994, after having received about 520,000 cubic meters of wastes. The Centre de l'Aube disposal facility is designed to receive a many types of waste produced by nuclear power plants, reprocessing, decommissioning, as well as by the industry, hospitals and armed forces. The limitation of radioactive transfer to man and the limitation of personnel exposure in all situations considered plausible require limiting the total activity of the waste disposed in the facility as well as the activity of each package. The paper presents how ANDRA has derived the activity-related acceptance criteria, based on the safety analysis. In the French methodology, activity is considered as end-point for deriving the concentration limits per package, whereas it is the starting point for deriving the total activity limits. For the concentration limits (called here LMA) the approach consists of five steps: the determination of radionuclides important for safety with regards to operational and long-term safety, the use of relevant safety scenarios as a tool to derive quantitative limits, the setting of dose constraint per situation associated with scenarios, the setting of contribution factor per radionuclide, and the calculation of concentration activity limits. An exhaustive survey has been performed and has shown that the totality of waste packages which should be delivered by waste generators are acceptable in terms of activity limits in the Centre de l'Aube. Examples of concentration activity limits derived from this methodology are presented. Furthermore those limits have been accepted by the French regulatory body and

  13. Technical basis for acceptance criteria on the susceptibility of digital systems to electromagnetic interference

    International Nuclear Information System (INIS)

    Ewing, P.D.; Korsah, K.; Antonescu, C.

    1992-01-01

    This paper discusses the development of the technical basis for establishing acceptance criteria on the susceptibility of digital systems to electromagnetic interference (EMI). The effort is sponsored by the US Nuclear Regulatory Commission and stems from the safety-related issues that need to be addressed with the application of digital instrumentation and controls systems in nuclear power plants. Designers of digital circuits are incorporating increasingly higher clock frequencies and lower logic voltage levels, thereby leading to the risk of susceptibility when spurious interference is misinterpreted as legitimate logic. Development of the technical basis for acceptance criteria centers around establishing good engineering practices to ensure that sufficient levels of electromagnetic compatibility (EMC) are maintained between the nuclear power plant's electronic and electromechanical systems. First, good EMC design and installation practices are needed to control the emissions from interference sources and their impact on other nearby circuits and systems. Then, a test and evaluation program is needed to outline the EMI tests to be performed, the associated test methods to be followed, and adequate test limits to ensure that the circuit or system under test meets the recommended guidelines. Test and evaluation should be followed by periodic maintenance to assess whether the recommended EMI control practices continue to be adhered to as part of the routine operation of the nuclear power plant. By following these steps, the probability of encountering safety-related problems associated with EMI will be greatly reduced

  14. RSE-M code progress in the field of examination evaluation and flaw acceptance criteria

    International Nuclear Information System (INIS)

    Barthelet, B.; Le Delliou, P.; Heliot, J.; Faidy, C.; Drubay, B.

    1995-01-01

    The RSE-M Code provides rules and requirements for in service inspection of light water cooled nuclear power plants. The code first edition was established by EDF and published in 1990 by AFCEN. In 1992, a second RSE-M project was launched by EDF and FRAMATOME with the objective to address a 1995 edition more completed considering the needs of owners, users, manufacturers and inspectors. This paper focuses on evaluation of examination results and presents the work done in the field of flaw acceptance criteria over the last three years. (author). 5 refs., 3 figs

  15. Annual Earnings Announcements and Market Reaction: The Influence of Screening Criteria for Thin Trading

    DEFF Research Database (Denmark)

    Møller, Peder Fredslund; Thinggaard, Frank; Lønroth, Helle L.

    2001-01-01

    This paper presents the findings of an event study of the Danish stock market price reactions to annual earnings announcements in the period 1993-1997, with a dual purpose. The primary purpose is to find out how market reactions vary with different screening criteria for thin trading. Our findings...... on this point suggest that the Danish stock market, although small, seems to have different segments of shares in relation to earnings announcements. Applying different screening criteria we find differences both in terms of how quickly the market reacts to earnings announcements and the relative quality...... purpose of our study is briefly to compare our findings with those of a similar study for the period 1971-1981. The aim is to find indications of developments in the Danish market's reactions to earnings announcements since that study. We find distinct indications that the Danish stock market in some...

  16. Nevada Test Site Waste Acceptance Criteria

    International Nuclear Information System (INIS)

    U.S. Department of Energy, Nevada Operations Office, Waste Acceptance Criteria

    1999-01-01

    This document provides the requirements, terms, and conditions under which the Nevada Test Site will accept low-level radioactive and mixed waste for disposal; and transuranic and transuranic mixed waste for interim storage at the Nevada Test Site

  17. Industry Application Emergency Core Cooling System Cladding Acceptance Criteria Early Demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Szilard, Ronaldo H. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Youngblood, Robert W. [FPoliSolutions LLC, Murrysville, PA (United States); Zhang, Hongbin [Idaho National Lab. (INL), Idaho Falls, ID (United States); Zhao, Haihua [Idaho National Lab. (INL), Idaho Falls, ID (United States); Bayless, Paul D. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Rabiti, Cristian [Idaho National Lab. (INL), Idaho Falls, ID (United States); Alfonsi, Andrea [Idaho National Lab. (INL), Idaho Falls, ID (United States); Smith, Curtis L. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Frepoli, Cesare [FPoliSolutions LLC, Murrysville, PA (United States); Yurko, Joseph P. [FPoliSolutions LLC, Murrysville, PA (United States); Swindlehurst, Gregg [GS Nuclear Consulting, Charlotte, NC (United States); Zoino, Angelo [Univ. of Rome Tor Vergata (Italy)

    2015-09-01

    The U. S. NRC is currently proposing rulemaking designated as “10 CFR 50.46c” to revise the loss-of-coolant-accident (LOCA)/emergency core cooling system (ECCS) acceptance criteria to include the effects of higher burnup on cladding performance as well as to address other technical issues. The NRC is also currently resolving the public comments with the final rule expected to be issued in April 2016. The impact of the final 50.46c rule on the industry may involve updating of fuel vendor LOCA evaluation models, NRC review and approval, and licensee submittal of new LOCA evaluations or re-analyses and associated technical specification revisions for NRC review and approval. The rule implementation process, both industry and NRC activities, is expected to take 4-6 years following the rule effective date. As motivated by the new rule, the need to use advanced cladding designs may be a result. A loss of operational margin may result due to the more restrictive cladding embrittlement criteria. Initial and future compliance with the rule may significantly increase vendor workload and licensee cost as a spectrum of fuel rod initial burnup states may need to be analyzed to demonstrate compliance. Consequently, there will be an increased focus on licensee decision making related to LOCA analysis to minimize cost and impact, and to manage margin. The proposed rule would apply to a light water reactor and to all cladding types.

  18. Acceptance criteria for the physical protection upgrade rule requirements for fixed sites. Information guide

    International Nuclear Information System (INIS)

    Dwyer, P.

    1980-09-01

    This document has been developed as a tool to assist in providing consistent evaluation of upgraded physical security plans submitted in response to the Physical Protection Upgrade Rule, effective March 25, 1980. It presents a means for assuring licensee compliance with every regulatory requirement of particular significance to the protection of the public health and safety. Acceptance criteria are included to determine the extent to which each licensee meets the regulatory requirements. The format parallels Regulatory Guide 5.52, Standard Format and Content of a Licensee Physical Protection Plan for Strategic Special Nuclear Material at Fixed Sites

  19. Flaw acceptance criteria taking into consideration the NDT: radiographic and ultrasonic testing. Analysis through the fracture mechanics methods

    International Nuclear Information System (INIS)

    Capurro, E.; Alicino, F.; Corvi, A.

    1993-01-01

    The present study compares and evaluates the flaw acceptance criteria of the non-destructive inspections meeting European Community standards, through the application of the fracture mechanics methods that were determined and verified by the previous activity. Some choices were made; these, however, do not change the general validity of the conclusions. Shaved full-penetration butt welds of Class 1 components making up the primary circuit were considered and the following parameters varied: standards: French, German, Italian (ASME III) and UK; material: AISI 316 and low alloy steel A 533; base material and weld metal; temperature: RT, 370 deg C for the austenitic and 260 deg C for the ferritic steel; ultrasonic and radiographic methods; defect position: surface and internal; stress condition: situations with different primary and secondary stresses. From a preliminary examination of this study it is evident that the large quantity of results available and the abundance of information contained therein make a simple and exhaustive synthesis difficult. In fact, different analyses are possible and we have, therefore, limited the research to activities to perform a comparison and a general evaluation of the acceptance criteria of the non-destructive testing. (authors). 57 refs., 25 figs., 11 tabs

  20. Thin films: Past, present, future

    Energy Technology Data Exchange (ETDEWEB)

    Zweibel, K

    1995-04-01

    This report describes the characteristics of the thin film photovoltaic modules necessary for an acceptable rate of return for rural areas and underdeveloped countries. The topics of the paper include a development of goals of cost and performance for an acceptable PV system, a review of current technologies for meeting these goals, issues and opportunities in thin film technologies.

  1. Data Quality Objectives for WTP Feed Acceptance Criteria - 12043

    Energy Technology Data Exchange (ETDEWEB)

    Arakali, Aruna V.; Benson, Peter A.; Duncan, Garth; Johnston, Jill C.; Lane, Thomas A.; Matis, George; Olson, John W. [Hanford Tank Waste Treatment and Immobilization Plant (United States); Banning, Davey L.; Greer, Daniel A.; Seidel, Cary M.; Thien, Michael G. [Hanford Tank Operations Contractor - Washington River Protection Solutions, Richland, WA 99354 (United States)

    2012-07-01

    The Hanford Tank Waste Treatment and Immobilization Plant (WTP) is under construction for the U.S. Department of Energy by Bechtel National, Inc. and subcontractor URS Corporation (contract no. DE-AC27-01RV14136). The plant when completed will be the world's largest nuclear waste treatment facility. Bechtel and URS are tasked with designing, constructing, commissioning, and transitioning the plant to the long term operating contractor to process the legacy wastes that are stored in underground tanks (from nuclear weapons production between the 1940's and the 1980's). Approximately 56 million gallons of radioactive waste is currently stored in these tanks at the Hanford Site in southeastern Washington. There are three major WTP facilities being constructed for processing the tank waste feed. The Pretreatment (PT) facility receives feed where it is separated into a low activity waste (LAW) fraction and a high level waste (HLW) fraction. These fractions are transferred to the appropriate (HLW or LAW) facility, combined with glass former material, and sent to high temperature melters for formation of the glass product. In addition to PT, HLW and LAW, other facilities in WTP include the Laboratory (LAB) for analytical services and the Balance of Facilities (BOF) for plant maintenance, support and utility services. The transfer of staged feed from the waste storage tanks and acceptance in WTP receipt vessels require data for waste acceptance criteria (WAC) parameters from analysis of feed samples. The Data Quality Objectives (DQO) development was a joint team effort between WTP and Tank Operations Contractor (TOC) representatives. The focus of this DQO effort was to review WAC parameters and develop data quality requirements, the results of which will determine whether or not the staged feed can be transferred from the TOC to WTP receipt vessels. The approach involved systematic planning for data collection consistent with EPA guidance for the seven

  2. Towards the development of workable acceptance criteria for the divertor CFC monoblock armour

    Energy Technology Data Exchange (ETDEWEB)

    D' Agata, E. [ITER International Team, ITER Joint Work Site, Boltzmannstr. 2, D-85748 Garching (Germany)]. E-mail: dagatae@itereu.de; Tivey, R. [ITER International Team, ITER Joint Work Site, Boltzmannstr. 2, D-85748 Garching (Germany)

    2005-11-15

    The plasma-facing components (PFCs) of the ITER divertor will be subjected to high heat flux (HHF). Carbon-fibre composite (CFC) is selected as the armour for the region of highest heat flux where the scrape-off layer of the plasma intercepts the vertical targets (VT). Failure of the armour to heat sink joints will compromise the performance of the divertor and could ultimately result in its failure and the shut down of the ITER machine. There are tens of thousands of CFCs to CuCrZr joints. The aim of the PFC design is to ensure that the divertor can continue to function even with the failure of a few joints. In preparation for writing the procurement specification for the ITER vertical target PFCs, a programme of work is underway with the objective of defining workable acceptance criteria for the PFC armour joints.

  3. Towards the development of workable acceptance criteria for the divertor CFC monoblock armour

    International Nuclear Information System (INIS)

    D'Agata, E.; Tivey, R.

    2005-01-01

    The plasma-facing components (PFCs) of the ITER divertor will be subjected to high heat flux (HHF). Carbon-fibre composite (CFC) is selected as the armour for the region of highest heat flux where the scrape-off layer of the plasma intercepts the vertical targets (VT). Failure of the armour to heat sink joints will compromise the performance of the divertor and could ultimately result in its failure and the shut down of the ITER machine. There are tens of thousands of CFCs to CuCrZr joints. The aim of the PFC design is to ensure that the divertor can continue to function even with the failure of a few joints. In preparation for writing the procurement specification for the ITER vertical target PFCs, a programme of work is underway with the objective of defining workable acceptance criteria for the PFC armour joints

  4. Selecting the Acceptance Criteria of Medicines in the Reimbursement List of Public Health Insurance of Iran, Using the "Borda" Method: a Pilot Study.

    Science.gov (United States)

    Viyanchi, Amir; Rasekh, Hamid Reza; Rajabzadeh Ghatari, Ali; SafiKhani, Hamid Reza

    2015-01-01

    Decision-making for medicines to be accepted in Iran's public health insurance reimbursement list is a complex process and involves factors, which should be considered in applying a coverage for medicine costs. These processes and factors are not wholly assessed, while assessment of these factors is an essential need for getting a transparent and evidence-based approach toward medicine reimbursement in Iran. This paper aims to show an evidence-based approach toward medicine selection criteria to inform the medical reimbursement decision makers in Iranian health insurance organizations. To explore an adaptable decision-making framework while incorporating a method called "Borda" in medicine reimbursement assessment, we used the help of an expert group including decision makers and clinical researchers who are also policy makers to appraise the five chief criteria that have three sub criteria (Precision, Interpretability, and Cost). Also software "Math-lab"7, "SPSS" 17 and Excel 2007 were used in this study. "Borda" estimates the amount of perceived values from different criteria and creates a range from one to five while providing a comprehensive measurement of a large spectrum of criteria. Participants reported that the framework provided an efficient approach to systematic consideration in a pragmatic format consisting of many parts to guide decision-makings, including criteria and value (a model with the core of Borda) and evidences (medicine reimbursement based on criteria). The most important criterion for medicine acceptance in health insurance companies, in Iran, is the "life-threatening" factor and "evidence quality" is accounted as the fifth important factor. This pilot study showed the usefulness of incorporating Borda in medicine reimbursement decisions to support a transparent and systematic appraisal of health insurance companies' deeds. Further research is needed to advance Borda-based approaches that are effective on health insurance decision making.

  5. Processing of Irradiated Graphite to Meet Acceptance Criteria for Waste Disposal. Results of a Coordinated Research Project

    International Nuclear Information System (INIS)

    2016-05-01

    Graphite is widely used in the nuclear industry and in research facilities and this has led to increasing amounts of irradiated graphite residing in temporary storage facilities pending disposal. This publication arises from a coordinated research project (CRP) on the processing of irradiated graphite to meet acceptance criteria for waste disposal. It presents the findings of the CRP, the general conclusions and recommendations. The topics covered include, graphite management issues, characterization of irradiated graphite, processing and treatment, immobilization and disposal. Included on the attached CD-ROM are formal reports from the participants

  6. Nevada Test Site waste acceptance criteria [Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    None

    1997-08-01

    Revision one updates the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive and mixed waste for disposal; and transuranic and transuranic mixed waste for interim storage at the NTS. Review each section of this document. This document is not intended to include all of the requirements; rather, it is meant as a guide toward meeting the regulations. All references in this document should be observed to avoid omission of requirements on which acceptance or rejection of waste will be based. The Department of Energy/Nevada Operations Office (DOE/NV) and support contractors are available to assist you in understanding or interpreting this document.

  7. Nevada Test Site waste acceptance criteria [Revision 1

    International Nuclear Information System (INIS)

    None

    1997-01-01

    Revision one updates the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive and mixed waste for disposal; and transuranic and transuranic mixed waste for interim storage at the NTS. Review each section of this document. This document is not intended to include all of the requirements; rather, it is meant as a guide toward meeting the regulations. All references in this document should be observed to avoid omission of requirements on which acceptance or rejection of waste will be based. The Department of Energy/Nevada Operations Office (DOE/NV) and support contractors are available to assist you in understanding or interpreting this document

  8. Derivation of quantitative acceptance criteria for disposal of radioactive waste to near surface facilities: Development and implementation of an approach for the post-closure phase

    International Nuclear Information System (INIS)

    Torres, C.

    2000-01-01

    The International Atomic Energy Agency has established a project to develop and illustrate, through practical examples, an approach that allows the derivation of quantitative waste acceptance criteria for near surface disposal of radioactive waste. The first phase focussed on the derivation of example post-closure safety waste acceptance criteria through the use of a safety assessment approach that allows for the derivation of values in a clear and well documented manner. The approach consists of five steps: the specification of the assessment context; the description of the disposal system; the development and justification of scenarios; the formulation and implementation of models; and the calculation and derivation of example values. The approach has been successfully used to derive activity values for the disposal of radioactive waste to illustrative near surface facilities. (author)

  9. Acceptance criteria considerations for miscellaneous wastes

    International Nuclear Information System (INIS)

    Irvine, A.R.; Forsberg, C.W.

    1987-01-01

    EPA standards set forth limitations regarding releases to the accessible environment adjacent to a geologic repository. The NRC criteria pertaining to waste form and engineered barrier performance place certain restrictions on the physical and chemical nature of the waste form and require substantially complete confinement of radioactivity until the high-heat-production period is past. After this period, the annual release of radionuclides from the waste package is normally limited to 1 part in 100,000 of the amounts calculated to be present at 1000-y decay. The regulation permits deviation from these criteria in exceptional circumstances. One such circumstance might be the absence of a significant perturbation in temperature around the stored waste. The lack of significant heat release will eliminate the hydrologic driving force for dispersal of radionuclides. Exceptional circumstances which potentially could justify a less stringent long-term release criterion are: small quantity of radioactivity, the nature of the radioactive species, and the nature of the geology in which the waste is to be emplaced. Because the MW after a suitable decay period have low heat release rates per unit volume, they apparently could be so emplaced in a repository that there would be no compelling need, according to the reasoning presented in 10 CFR 60, for a 1000-y container. Regarding attainment of the specified long-term release rate criterion, neither the solubility limits for the various waste forms nor the conductance of potential migration barriers are currently adequately characterized. The relatively small total heat generation rate for the MW in combination with the usual low volumetric heat generation rate apparently will allow application of migration barriers in a low temperature environment where barrier performance would be expected to be unchanged with time

  10. Recommendations for Glass Durability Test Criteria

    International Nuclear Information System (INIS)

    Strachan, D.M.

    1999-01-01

    The objective of this short report is to define a set of activities that should lead to a specification for a test that can be used as one of the acceptance criteria and as an indicator of acceptable long-term behavior in contact with water. Since the glass composition is not yet defined and is likely to change as the composition of the waste changes, a strategy for developing criteria for what is acceptable involves a series of tests and modeling activities. The results of these activities lead to a criterion for an acceptable product and the data that are needed to reliably determine the behavior of the glass in the storage environment

  11. DOE natural phenomenal hazards design and evaluation criteria

    International Nuclear Information System (INIS)

    Murray, R.C.; Nelson, T.A.; Short, S.A.; Kennedy, R.P.; Chander, H.; Hill, J.R.; Kimball, J.K.

    1994-10-01

    It is the policy of the Department of Energy (DOE) to design, construct, and operate DOE facilities so that workers, the general public, and the environment are protected from the impacts of natural phenomena hazards (NPH). Furthermore, DOE has established explicit goals of acceptable risk for NPH performance. As a result, natural phenomena hazard (earthquake, extreme wind, and flood) design and evaluation criteria for DOE facilities have been developed based on target probabilistic performance goals. These criteria include selection of design/evaluation NPH input from probabilistic hazard curves combined with commonly practiced deterministic response evaluation methods and acceptance criteria with controlled levels of conservatism. For earthquake considerations, conservatism is intentionally introduced in specification of material strengths and capacities, in the allowance of limited inelastic behavior, and by a seismic scale factor. Criteria have been developed following a graded approach for several performance goals ranging from that appropriate for normal-use facilities to that appropriate for facilities involving hazardous or critical operations. Performance goals are comprised of qualitative expressions of acceptable behavior and of target quantitative probabilities that acceptable limits of behavior are maintained. The criteria are simple procedures but have a rigorous basis. This paper addresses DOE seismic design and evaluation criteria

  12. Acceptance criteria for non-destructive examination of double-shell tanks

    International Nuclear Information System (INIS)

    Jensen, C.E.

    1995-09-01

    This supporting document provides requirements for acceptance of relevant indications found during non-destructive examination of double-shell tanks (DSTs) at Hanford 200 areas. Requirements for evaluation of relevant indications are provided to determine acceptability of continued safe operation of the DSTs. Areas of the DSTs considered include the tank wall vapor space, liquid-vapor interface, wetted tank wall, sludge-liquid interface, and the knuckle region

  13. Ammunition Peculiar Equipment (APE) 1995, NIR Propellant Analyzer, to MIL-STD-398, Military Standard Shields, Operational for Ammunition Operations, Criteria for Design of and Tests for Acceptance

    National Research Council Canada - National Science Library

    2003-01-01

    ... (SJMAC-DEM) to test the Ammunition Peculiar Equipment (APE) 1995 NIR Propellant Analyzer, to MIL-STD-398, "Military Standard Shields, Operational for Ammunition Operations, Criteria for Design of and Tests for Acceptance...

  14. Acceptance Probability (P a) Analysis for Process Validation Lifecycle Stages.

    Science.gov (United States)

    Alsmeyer, Daniel; Pazhayattil, Ajay; Chen, Shu; Munaretto, Francesco; Hye, Maksuda; Sanghvi, Pradeep

    2016-04-01

    This paper introduces an innovative statistical approach towards understanding how variation impacts the acceptance criteria of quality attributes. Because of more complex stage-wise acceptance criteria, traditional process capability measures are inadequate for general application in the pharmaceutical industry. The probability of acceptance concept provides a clear measure, derived from specific acceptance criteria for each quality attribute. In line with the 2011 FDA Guidance, this approach systematically evaluates data and scientifically establishes evidence that a process is capable of consistently delivering quality product. The probability of acceptance provides a direct and readily understandable indication of product risk. As with traditional capability indices, the acceptance probability approach assumes that underlying data distributions are normal. The computational solutions for dosage uniformity and dissolution acceptance criteria are readily applicable. For dosage uniformity, the expected AV range may be determined using the s lo and s hi values along with the worst case estimates of the mean. This approach permits a risk-based assessment of future batch performance of the critical quality attributes. The concept is also readily applicable to sterile/non sterile liquid dose products. Quality attributes such as deliverable volume and assay per spray have stage-wise acceptance that can be converted into an acceptance probability. Accepted statistical guidelines indicate processes with C pk > 1.33 as performing well within statistical control and those with C pk  1.33 is associated with a centered process that will statistically produce less than 63 defective units per million. This is equivalent to an acceptance probability of >99.99%.

  15. Development of comprehensive waste acceptance criteria for commercial nuclear waste

    International Nuclear Information System (INIS)

    O'Hara, F.A.; Miller, N.E.; Ausmus, B.S.; Yates, K.R.; Means, J.L.; Christensen, R.N.; Kulacki, F.A.

    1979-01-01

    A detailed methodology is presented for the identification of the characteristics of commercial nuclear waste which may require criteria. This methodology is analyzed as a six-step process which begins with identification of waste operations and proceeds until the waste characteristics affecting the potential release of radionuclides are determined. All waste types and operations were analyzed using the methodology presented. Several illustrative example are included. It is found that thirty-three characteristics can be identified as possibly requiring criteria

  16. Are regulation-driven performance criteria still acceptable? - The German point of view.

    Science.gov (United States)

    Orth, Matthias

    2015-05-01

    Performance criteria should be a challenge for the laboratories to improve their quality. In countries with mandatory proficiency testing, the definition of performance criteria is a particular issue. If the definition of performance criteria is mandated from the regulatory bodies to medico-scientific institutions, scientific approaches (i.e., based on biological variation), the state-of-the-art approach (i.e., based on technical feasibility) as well as medical needs can be used to set up performance criteria such as the Richtlinie der Bundesärztekammer (RiliBÄK; Guideline of the German Medical Association on Quality Assurance in Medical Laboratory Examinations) in Germany. The experiences with RiliBÄK show that these performance criteria have to be revised on an ongoing basis.

  17. The effect of interpersonal rejection on attentional biases regarding thin-ideal and non-thin images: The moderating role of body weight- and shape-based self-worth.

    Science.gov (United States)

    Rieger, Elizabeth; Dolan, Ashleigh; Thomas, Brittany; Bell, Jason

    2017-09-01

    Interpersonal dysfunction and weight/shape-based self-worth have been implicated as key constructs for eating disorders, although the relationship between these two concepts is under-researched. This study investigated the moderating role of weight/shape-based self-worth in terms of the impact of interpersonal rejection on attentional bias regarding thin-ideal and non-thin images. Participants were 94 females without an eating disorder, who were exposed to either interpersonal rejection or acceptance (using the Cyberball paradigm), and subsequently assessed in terms of their attentional biases regarding thin-ideal and non-thin images. Results revealed that weight/shape-based self-worth moderated the relationship between interpersonal rejection/acceptance and attentional biases for thin-ideal (but not non-thin) images. Specifically, participants with a greater tendency to base their self-worth on weight/shape demonstrated reduced avoidance of thin-ideal images when rejected relative to those who were accepted. The findings support the role of interpersonal rejection in eliciting attentional disturbances among those with higher body weight/shape-based self-worth. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Sustainability and acceptance - new challenges for nuclear energy

    International Nuclear Information System (INIS)

    Lensa, W. von

    2001-01-01

    This paper discusses the concept of sustainability in relation to acceptance of nuclear energy. Acceptance is viewed in terms of public acceptance, industrial acceptance, and internal acceptance/consensus within the nuclear community. It addresses sustainability criteria, the need for innovation, and the different levels of acceptability. The mechanisms of risk perception are discussed along with the technological consequences from risk perception mechanisms leading to specific objections against nuclear energy. (author)

  19. Processing of Irradiated Graphite to Meet Acceptance Criteria for Waste Disposal. Results of a Coordinated Research Project. Companion CD-ROM

    International Nuclear Information System (INIS)

    2016-05-01

    Graphite is widely used in the nuclear industry and in research facilities and this has led to increasing amounts of irradiated graphite residing in temporary storage facilities pending disposal. This publication arises from a coordinated research project (CRP) on the processing of irradiated graphite to meet acceptance criteria for waste disposal. It presents the findings of the CRP, the general conclusions and recommendations. The topics covered include, graphite management issues, characterization of irradiated graphite, processing and treatment, immobilization and disposal. Included on the attached CD-ROM are formal reports from the participants

  20. Electricity supply between acceptance, acceptability and social compatibility; Energieversorgung zwischen Akzeptanz, Akzeptabilitaet und Sozialvertraeglichkeit

    Energy Technology Data Exchange (ETDEWEB)

    Schubert, Katharina; Koch, Marco K. [Bochum Univ. (Germany). Lehrstuhl Energiesysteme und Energiewirtschaft (LEE)

    2012-11-01

    Acceptance promotion is supposed to be an indispensable premise for a successful realization of an energy concept. The contribution identifies deficiencies of the energy policy, including intransparency, complexity of decision procedures, for instance in case of the so called energy transmission line extension acceleration law, that has caused irritation and anger in the public. The justification of acceptance promotion is questioned in connection with the German nuclear policy reversal following the Fukushima accident. A research program ''public acceptance of large-scale power plants for electricity generation'' is presented. The issues criteria and limits of acceptability are of main importance for this discussion.

  1. From waste packages acceptance criteria to waste packages acceptance process at the Centre de l'Aube disposal facility

    International Nuclear Information System (INIS)

    Dutzer, M.

    2003-01-01

    The Centre de l'Aube disposal facility has now been operated for 10 years. At the end of 2001, about 124,000 m3 of low and intermediate level short lived waste packages, representing 180,000 packages, have been disposed, for a total capacity of 1,000,000 m3. The flow of waste packages is now between 12 and 15,000 m3 per year, that is one third of the flow that was taken into account for the design of the repository. It confirms the efforts by waste generators to minimise waste production. This flow represents 25 to 30,000 packages, 50% are conditioned into the compaction facility of the repository, so that 17,000 packages are disposed per year. 54 disposal vaults have been closed. In 1996-1999, the safety assessment of the repository have been reviewed, taking into account the experience of operation. This assessment was investigated by the regulatory body and, subsequently, a so-called 'definitive license' to operate was granted to ANDRA on September 2, 1999 with updated licensing requirements. Another review will be performed in 2004. To ensure a better consistency with the safety assessment of the facility, Andra issued new technical requirements for waste packages at the end of 2000. Discussions with waste generators also showed that the waste package acceptance process should be improved to provide a more precise definition of operational criteria to comply with in waste conditioning facilities. Consequently, a new approach has been implemented since 2000. (orig.)

  2. Safety criteria for nuclear chemical plants

    International Nuclear Information System (INIS)

    Ball, P.W.; Curtis, L.M.

    1983-01-01

    Safety measures have always been required to limit the hazards due to accidental release of radioactive substances from nuclear power plants and chemical plants. The risk associated with the discharge of radioactive substances during normal operation has also to be kept acceptably low. BNFL (British Nuclear Fuels Ltd.) are developing risk criteria as targets for safe plant design and operation. The numerical values derived are compared with these criteria to see if plants are 'acceptably safe'. However, the criteria are not mandatory and may be exceeded if this can be justified. The risk assessments are subject to independent review and audit. The Nuclear Installations Inspectorate also has to pass the plants as safe. The assessment principles it uses are stated. The development of risk criteria for a multiplant site (nuclear chemical plants tend to be sited with many others which are related functionally) is discussed. This covers individual members of the general public, societal risks, risks to the workforce and external hazards. (U.K.)

  3. Acceptance test procedure for Project W-280

    International Nuclear Information System (INIS)

    Stites, C.G.

    1994-01-01

    This Document is the Acceptance Test Procedure for 200 Area C and SY Tank Farm Lighting Upgrade. This Acceptance Test Procedure has been prepared to demonstrate that the Tank Farm Lighting Systems function correctly as required by project criteria and as intended by design

  4. Simplified probabilistic approach to determine safety factors in deterministic flaw acceptance criteria

    International Nuclear Information System (INIS)

    Barthelet, B.; Ardillon, E.

    1997-01-01

    The flaw acceptance rules in nuclear components rely on deterministic criteria supposed to ensure the safe operating of plants. The interest of having a reliable method of evaluating the safety margins and the integrity of components led Electricite de France to launch a study to link safety factors with requested reliability. A simplified analytical probabilistic approach is developed to analyse the failure risk in Fracture Mechanics. Assuming lognormal distributions of the main random variables, it is possible considering a simple Linear Elastic Fracture Mechanics model, to determine the failure probability as a function of mean values and logarithmic standard deviations. The 'design' failure point can be analytically calculated. Partial safety factors on the main variables (stress, crack size, material toughness) are obtained in relation with reliability target values. The approach is generalized to elastic plastic Fracture Mechanics (piping) by fitting J as a power law function of stress, crack size and yield strength. The simplified approach is validated by detailed probabilistic computations with PROBAN computer program. Assuming reasonable coefficients of variations (logarithmic standard deviations), the method helps to calibrate safety factors for different components taking into account reliability target values in normal, emergency and faulted conditions. Statistical data for the mechanical properties of the main basic materials complement the study. The work involves laboratory results and manufacture data. The results of this study are discussed within a working group of the French in service inspection code RSE-M. (authors)

  5. Proposed radiological protection criteria for waste disposal options

    International Nuclear Information System (INIS)

    Hill, M.D.

    1981-01-01

    Criteria which are based solely on the consequences of releases of radionuclides, that is doses to man, are inappropriate for decisions on the acceptability of many of the disposal options for solid wastes. The risks associated with disposal options in which the intention is to isolate wastes from the biosphere for any length of time have two major components: the probability that a release of radionuclides will occur and the probability that subsequent radiation doses will give rise to deleterious effects. It is therefore necessary to develop criteria which embody the basic radiological principle of keeping risks to acceptable levels and take account of both components of risk. In this paper proposed criteria are described and some of the implications of adopting these criteria are discussed. (author)

  6. The use of economic criteria in providing a basis for safe reactor operation

    International Nuclear Information System (INIS)

    Graham, J.

    1989-01-01

    Probabilistic criteria based upon an acceptance measure of protection for owner investment can complete the range of design probabilistic criteria between those set by acceptance public safety and those set by acceptable reliability in plant operation. Criteria which address the protection of owner investment have the benefit of lowering risk in adjacent risk regions by providing greater reliability in operation as well as less risk to the safety of the public and the environment. Such investment protection criteria are currently being used to extend plant life but they could also be used very beneficially as part of the initial design process. In this paper trial criteria are suggested which address the risk of extended plant shutdown with the resultant necessity to purchase replacement power, and the risk of replacement of expensive plant components. Additional financial assessment is required to ensure that there is a proper correlation between acceptable measures of owner-investment protection and the levels of probabilistic defence suggested, but the trial criteria proposed can be used as important practical design criteria

  7. NWTS program criteria for mined geologic disposal of nuclear waste: program objectives, functional requirements, and system performance criteria

    International Nuclear Information System (INIS)

    1981-04-01

    At the present time, final repository criteria have not been issued by the responsible agencies. This document describes general objectives, requirements, and criteria that the DOE intends to apply in the interim to the National Waste Terminal Storage (NWTS) Program. These objectives, requirements, and criteria have been developed on the basis of DOE's analysis of what is needed to achieve the National objective of safe waste disposal in an environmentally acceptable and economic manner and are expected to be consistent with anticipated regulatory standards. The qualitative statements in this document address the broad issues of public and occupational health and safety, institutional acceptability, engineering feasibility, and economic considerations. A comprehensive set of criteria, general and project specific, of which these are a part, will constitute a portion of the technical basis for preparation and submittal by the DOE of formal documents to support future license applications for nuclear waste repositories

  8. NWTS program criteria for mined geologic disposal of nuclear waste: program objectives, functional requirements, and system performance criteria

    Energy Technology Data Exchange (ETDEWEB)

    None

    1981-04-01

    At the present time, final repository criteria have not been issued by the responsible agencies. This document describes general objectives, requirements, and criteria that the DOE intends to apply in the interim to the National Waste Terminal Storage (NWTS) Program. These objectives, requirements, and criteria have been developed on the basis of DOE's analysis of what is needed to achieve the National objective of safe waste disposal in an environmentally acceptable and economic manner and are expected to be consistent with anticipated regulatory standards. The qualitative statements in this document address the broad issues of public and occupational health and safety, institutional acceptability, engineering feasibility, and economic considerations. A comprehensive set of criteria, general and project specific, of which these are a part, will constitute a portion of the technical basis for preparation and submittal by the DOE of formal documents to support future license applications for nuclear waste repositories.

  9. Top-level regulatory criteria for the standard MHTGR

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-10-15

    The Licensing Plan for the Standard MHTGR (Ref. 1) describes a program to support a U.S. Nuclear Regulatory Commission (NRC) design review and approval. The Plan calls for the submittal of Top-Level Regulatory Criteria to the NRC for concurrence with their completeness and acceptability for the MHTGR program. The Top-Level Regulatory Criteria are defined as the standards for judging licensability that directly specify acceptable limits for protection of the public health and safety and the environment. The criteria proposed herein are for normal plant operation and a broad spectrum of anticipated events, including accidents. The approach taken is to define a set of criteria which are general as opposed to being design specific. Specifically, it is recommended that criteria be met which: 1. Are less prescriptive than current regulation, thereby encouraging maximum flexibility in design approaches. 2. Are measurable. 3. Are not more strict than the criteria for current power plants.

  10. Present state of the design and realization of regional radioactive waste depositories and waste acceptance criteria for disposal

    International Nuclear Information System (INIS)

    Kortus, J.

    1988-01-01

    Surface type regional depositories for radioactive wastes from nuclear power plants are described in detail. The depository of the Mochovce nuclear power plant is located near the plant, that of the Dukovany nuclear power plant is directly on the premises of the plant. Particular attention is paid to the design of the monolithic reinforced concrete pits, draining of rainwater from their surface, draining of seeping rainwater from the pit environment by means of a double drainage system, and insulation of the pits against water. The construction of the Mochovce depository started in 1987; some experience gained from this activity is presented. The radioactive waste acceptance criteria for depositories of this kind, based on safety analysis, are given. (author). 2 figs

  11. Modeling Carbon Turnover in Five Terrestrial Ecosystems in the Boreal Zone Using Multiple Criteria of Acceptance

    International Nuclear Information System (INIS)

    Karlberg, Louise; Gustafsson, David; Jansson, Per-Erik

    2006-01-01

    Estimates of carbon fluxes and turnover in ecosystems are key elements in the understanding of climate change and in predicting the accumulation of trace elements in the biosphere. In this paper we present estimates of carbon fluxes and turnover times for five terrestrial ecosystems using a modeling approach. Multiple criteria of acceptance were used to parameterize the model, thus incorporating large amounts of multi-faceted empirical data in the simulations in a standardized manner. Mean turnover times of carbon were found to be rather similar between systems with a few exceptions, even though the size of both the pools and the fluxes varied substantially. Depending on the route of the carbon through the ecosystem, turnover times varied from less than one year to more than one hundred, which may be of importance when considering trace element transport and retention. The parameterization method was useful both in the estimation of unknown parameters, and to identify variability in carbon turnover in the selected ecosystems

  12. Sediment quality criteria: A review with recommendations for developing criteria for the Hanford Site

    Energy Technology Data Exchange (ETDEWEB)

    Driver, C.J.

    1994-05-01

    Criteria for determining the quality of liver sediment are necessary to ensure that concentrations of contaminants in aquatic systems are within acceptable limits for the protection of aquatic and human life. Such criteria should facilitate decision-making about remediation, handling, and disposal of contaminants. Several approaches to the development of sediment quality criteria (SQC) have been described and include both descriptive and numerical methods. However, no single method measures all impacts at all times to all organisms (U.S. EPA 1992b). The U.S. EPA`s interest is primarily in establishing chemically based, numerical SQC that are applicable nation-wide (Shea 1988). Of the approaches proposed for SQC development, only three are being considered for numerical SQC on a national level. These approaches include an Equilibrium Partitioning Approach, a site-specific method using bioassays (the Apparent Effects Threshold Approach), and an approach similar to EPA`s water quality criteria (Pavlou and Weston 1984). Although national (or even regional) criteria address a number of political, litigative, and engineering needs, some researchers feel that protection of benthic communities require site-specific, biologically based criteria (Baudo et al. 1990). This is particularly true for areas where complex mixtures of contaminants are present in sediments. Other scientifically valid and accepted procedures for freshwater SQC include a background concentration approach, methods using field or spiked bioassays, a screening level concentration approach, the Apparent Effects Threshold Approach, the Sediment Quality Triad, the International Joint Commission Sediment Assessment Strategy, and the National Status and Trends Program Approach. The various sediment assessment approaches are evaluated for application to the Hanford Reach and recommendations for Hanford Site sediment quality criteria are discussed.

  13. Early Site Permit Demonstration Program: Regulatory criteria evaluation report

    International Nuclear Information System (INIS)

    1993-03-01

    The primary objective of the Early Site Plan Demonstration Program (ESPDP) is to demonstrate successfully the use of 10CFR52 to obtain ESPs for one or more US sites for one (or more) ALWR nuclear power plants. It is anticipated that preparation of the ESP application and interaction with NRC during the application review process will result not only in an ESP for the applicant(s) but also in the development of criteria and definition of processes, setting the precedent that facilitates ESPs for subsequent ESP applications. Because siting regulatory processes and acceptance criteria are contained in over 100 separate documents, comprehensive licensing and technical reviews were performed to establish whether the requirements and documentation are self-consistent, whether the acceptance criteria are sufficiently well-defined and clear, and whether the licensing process leading to the issuance of an ESP is unambiguously specified. This document provides appendices A and B of this report. Appendix A contains a list of regulations, regulatory guidance, and acceptance criteria; Appendix B contains a cross-reference index of siting-related documentation

  14. Crew Transportation Technical Standards and Design Evaluation Criteria

    Science.gov (United States)

    Lueders, Kathryn L.; Thomas, Rayelle E. (Compiler)

    2015-01-01

    Crew Transportation Technical Standards and Design Evaluation Criteria contains descriptions of technical, safety, and crew health medical processes and specifications, and the criteria which will be used to evaluate the acceptability of the Commercial Providers' proposed processes and specifications.

  15. Risk based seismic design criteria

    International Nuclear Information System (INIS)

    Kennedy, R.P.

    1999-01-01

    In order to develop a risk based seismic design criteria the following four issues must be addressed: (1) What target annual probability of seismic induced unacceptable performance is acceptable? (2) What minimum seismic margin is acceptable? (3) Given the decisions made under Issues 1 and 2, at what annual frequency of exceedance should the safe-shutdown-earthquake (SSE) ground motion be defined? (4) What seismic design criteria should be established to reasonably achieve the seismic margin defined under Issue 2? The first issue is purely a policy decision and is not addressed in this paper. Each of the other three issues are addressed. Issues 2 and 3 are integrally tied together so that a very large number of possible combinations of responses to these two issues can be used to achieve the target goal defined under Issue 1. Section 2 lays out a combined approach to these two issues and presents three potentially attractive combined resolutions of these two issues which reasonably achieves the target goal. The remainder of the paper discusses an approach which can be used to develop seismic design criteria aimed at achieving the desired seismic margin defined in resolution of Issue 2. Suggestions for revising existing seismic design criteria to more consistently achieve the desired seismic margin are presented. (orig.)

  16. Experimental activity on the definition of acceptance criteria for the ITER divertor plasma facing components

    International Nuclear Information System (INIS)

    Escourbiac, F.; Constans, S.; Vignal, N.; Cantone, V.; Richou, M.; Durocher, A.; Riccardi, B.; Bobin, I.; Jouvelot, J.L.; Merola, M.

    2009-01-01

    Tens of thousands of armor/heat sink joints will be produced by the industry during the manufacturing of ITER divertor PFC, statistically, there is a probability that joints with defects be delivered. The purpose of this paper is to study the detection and evolution during operation of calibrated defects artificially implemented on samples, as an experimental basis for the definition of acceptance criteria for the bond armor/heat sink in the frame of industrial manufacturing conditions.It was found that current CFC monoblock design option was compatible with the heat loads specified at the lower part of the vertical target (up to 20 MW/m 2 ), including the presence of armor/heat sink defects (up to 50 deg. extension for a location at 0 deg. or 45 deg.) detectable with NDE techniques developed in Europe (US, SATIR). The current W monoblock design appeared suitable for the upper part of the vertical target with defects extension up to 50 deg. but is not adapted for heat flux of 20 MW/m 2 . The studied W flat tile design proved to be compatible with fluxes of 5 MW/m 2 but unable to sustain cycling fluxes of 10 MW/m 2 .

  17. Probabilistic relationships in acceptable risk studies

    International Nuclear Information System (INIS)

    Benjamin, J.R.

    1977-01-01

    Acceptable risk studies involve uncertainties in future events; consequences and associated values, the acceptability levels, and the future decision environment. Probabilistic procedures afford the basic analytical tool to study the influence of each of these parameters on the acceptable risk decision, including their interrelationships, and combinations. A series of examples are presented in the paper in increasing complexity to illustrate the principles involved and to quantify the relationships to the acceptable risk decision. The basic objective of such studies is to broaden the scientific basis of acceptable risk decision making. It is shown that rationality and consistency in decision making is facilitated by such studies and that rather simple relationships exist in many situations of interest. The variation in criteria associated with an increase in the state of knowledge or change in the level of acceptability is also discussed. (Auth.)

  18. Probabilistic relationships in acceptable risk studies

    International Nuclear Information System (INIS)

    Benjamin, J.R.

    1977-01-01

    Acceptable risk studies involve uncertainties in future events: consequences and associated values, the acceptability levels, and the future decision environment. Probabilistic procedures afford the basic analytical tool to study the influence of each of these parameters on the acceptable risk decision, including their interrelationships, and combinations. A series of examples are presented in the paper in increasing complexity to illustrate the principles involved and to quantify the relationships to the acceptable risk decision. The basic objective of such studies is to broaden the scientific basis of acceptable risk decision making. It is shown that rationality and consistency in decision making is facilitated by such studies and that rather simple relationships exist in many situations of interest. The variation in criteria associated with an increase in the state of knowledge or change in the level of acceptability is also discussed

  19. Feasibility and acceptability of electronic symptom surveillance with clinician feedback using the Patient-Reported Outcomes version of Common Terminology Criteria for Adverse Events (PRO-CTCAE) in Danish prostate cancer patients

    DEFF Research Database (Denmark)

    Baeksted, Christina; Pappot, Helle; Nissen, Aase

    2017-01-01

    Background: The aim was to examine the feasibility, acceptability and clinical utility of electronic symptom surveillance with clinician feedback using a subset of items drawn from the Patient-Reported Outcomes version of Common Terminology Criteria for Adverse Events (PRO-CTCAE) in a cancer...

  20. Safety criteria from the public viewpoint

    International Nuclear Information System (INIS)

    Renn, O.

    1994-01-01

    The paper attempts to outline the scope and limits of a consensus for the evaluation of energy systems, particularly nuclear energy. It is divided into four sections. The first section deals with factual acceptance of technology, while the second inquires into the specific acceptance of nuclear energy, i.e., public perception and valuation of nuclear energy today. The third section discusses criteria of acceptability. In the fourth section, finally, the author deals with questions concerning an energy consensus and presents his own model for approaching this issue. (orig.) [de

  1. Technical considerations associated with spent fuel acceptance. Final report

    International Nuclear Information System (INIS)

    Supko, E.M.

    1996-06-01

    This study was initiated by the Electric Power Research Institute (EPRI) to identify technical considerations associated with spent fuel acceptance and implementation of a waste management system that includes the use of transportable storage systems, and to serve as an opening dialogue among Standard Contract Holders and the department of Energy's Office of Civilian Radioactive Waste management (OCRWM) prior to the development of waste acceptance criteria or issuance of a Notice of Proposed Rulemaking by OCRWM to amend the Standard Contract. The original purpose of the Notice of Proposed Rulemaking was to address changes to the Standard Contract to implement a multi-purpose canister based system and to address other issues that were not adequately addressed in the standard contract. Even if DOE does not develop a multi-purpose canister based system for waste acceptance, it will still be necessary to develop waste acceptance criteria in order to accept spent fuel in transportable storage systems that are being deployed for at-reactor storage. In this study, technical issues associated with spent fuel acceptance will be defined and potential options and alternatives for resolution of technical considerations will be explored

  2. Criteria for the development and use of the methodology for environmentally-acceptable fossil energy site evaluation and selection. Volume 2. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Eckstein, L.; Northrop, G.; Scott, R.

    1980-02-01

    This report serves as a companion document to the report, Volume 1: Environmentally-Acceptable Fossil Energy Site Evaluation and Selection: Methodology and Users Guide, in which a methodology was developed which allows the siting of fossil fuel conversion facilities in areas with the least environmental impact. The methodology, known as SELECS (Site Evaluation for Energy Conversion Systems) does not replace a site specific environmental assessment, or an environmental impact statement (EIS), but does enhance the value of an EIS by thinning down the number of options to a manageable level, by doing this in an objective, open and selective manner, and by providing preliminary assessment and procedures which can be utilized during the research and writing of the actual impact statement.

  3. Cone penetrometer moisture probe acceptance test report

    International Nuclear Information System (INIS)

    Barnes, G.A.

    1996-01-01

    This Acceptance Test Report (ATR) documents the results of WHC-SD-WM-ATP-146 (Prototype Cone Penetrometer Moisture Probe Acceptance Test Procedure) and WHC-SD-WM-ATP-145 (Cone Penetrometer Moisture Probe Acceptance Test Procedure). The master copy of WHC-SD-WM-ATP-145 can be found in Appendix A and the master copy of WHC-SD-WM-ATP-146 can be found in Appendix B. Also included with this report is a matrix showing design criteria of the cone penetrometer moisture probe and the verification method used (Appendix C)

  4. On Maximal Hard-Core Thinnings of Stationary Particle Processes

    Science.gov (United States)

    Hirsch, Christian; Last, Günter

    2018-02-01

    The present paper studies existence and distributional uniqueness of subclasses of stationary hard-core particle systems arising as thinnings of stationary particle processes. These subclasses are defined by natural maximality criteria. We investigate two specific criteria, one related to the intensity of the hard-core particle process, the other one being a local optimality criterion on the level of realizations. In fact, the criteria are equivalent under suitable moment conditions. We show that stationary hard-core thinnings satisfying such criteria exist and are frequently distributionally unique. More precisely, distributional uniqueness holds in subcritical and barely supercritical regimes of continuum percolation. Additionally, based on the analysis of a specific example, we argue that fluctuations in grain sizes can play an important role for establishing distributional uniqueness at high intensities. Finally, we provide a family of algorithmically constructible approximations whose volume fractions are arbitrarily close to the maximum.

  5. Heat exchanger, head and shell acceptance criteria

    International Nuclear Information System (INIS)

    Lam, P.S.; Sindelar, R.L.

    1992-09-01

    Instability of postulated flaws in the head component of the heat exchanger could not produce a large break, equivalent to a DEGB in the PWS piping, due to the configuration of the head and restraint provided by the staybolts. Rather, leakage from throughwall flaws in the head would increase with flaw length with finite leakage areas that are bounded by a post-instability flaw configuration. Postulated flaws at instability in the shell of the heat exchanger or in the cooling water nozzles could produce a large break in the Cooling Water System (CWS) pressure boundary. An initial analysis of flaw stability for postulated flaws in the heat exchanger head was performed in January 1992. This present report updates that analysis and, additionally, provides acceptable flaw configurations to maintain defined structural or safety margins against flaw instability of the external pressure boundary components of the heat exchanger, namely the head, shell, and cooling water nozzles. Structural and flaw stability analyses of the heat exchanger tubes, the internal pressure boundary of the heat exchangers or interface boundary between the PWS and CWS, were previously completed in February 1992 as part of the heat exchanger restart evaluation and are not covered in this report

  6. Safety and reliability criteria

    International Nuclear Information System (INIS)

    O'Neil, R.

    1978-01-01

    Nuclear power plants and, in particular, reactor pressure boundary components have unique reliability requirements, in that usually no significant redundancy is possible, and a single failure can give rise to possible widespread core damage and fission product release. Reliability may be required for availability or safety reasons, but in the case of the pressure boundary and certain other systems safety may dominate. Possible Safety and Reliability (S and R) criteria are proposed which would produce acceptable reactor design. Without some S and R requirement the designer has no way of knowing how far he must go in analysing his system or component, or whether his proposed solution is likely to gain acceptance. The paper shows how reliability targets for given components and systems can be individually considered against the derived S and R criteria at the design and construction stage. Since in the case of nuclear pressure boundary components there is often very little direct experience on which to base reliability studies, relevant non-nuclear experience is examined. (author)

  7. A systematic review of patient acceptance of consumer health information technology.

    Science.gov (United States)

    Or, Calvin K L; Karsh, Ben-Tzion

    2009-01-01

    A systematic literature review was performed to identify variables promoting consumer health information technology (CHIT) acceptance among patients. The electronic bibliographic databases Web of Science, Business Source Elite, CINAHL, Communication and Mass Media Complete, MEDLINE, PsycArticles, and PsycInfo were searched. A cited reference search of articles meeting the inclusion criteria was also conducted to reduce misses. Fifty-two articles met the selection criteria. Among them, 94 different variables were tested for associations with acceptance. Most of those tested (71%) were patient factors, including sociodemographic characteristics, health- and treatment-related variables, and prior experience or exposure to computer/health technology. Only ten variables were related to human-technology interaction; 16 were organizational factors; and one was related to the environment. In total, 62 (66%) were found to predict acceptance in at least one study. Existing literature focused largely on patient-related factors. No studies examined the impact of social and task factors on acceptance, and few tested the effects of organizational or environmental factors on acceptance. Future research guided by technology acceptance theories should fill those gaps to improve our understanding of patient CHIT acceptance, which in turn could lead to better CHIT design and implementation.

  8. A comparison between criteria for diagnosing atopic eczema in infants

    DEFF Research Database (Denmark)

    Jøhnke, H; Vach, W; Norberg, L A

    2005-01-01

    Research Centre (DARC) criteria developed for this study and doctor-diagnosed visible eczema with typical morphology and atopic distribution. Additionally, the U.K. diagnostic criteria based on a questionnaire were used at 1 year of age. Agreement between the four criteria was analysed at each time point...... the four criteria demonstrated that cumulative incidences showed better agreement than point prevalence values. CONCLUSIONS: Agreement between different criteria for diagnosing AE was acceptable, but the mild cases constituted a diagnostic problem, although they were in the minority. Repeated examinations...

  9. Development of wall thinning screening system and its application to a commercial nuclear power plant

    International Nuclear Information System (INIS)

    Ryu, Kyung Ha; Hwang, Il Soon; Kim, Ji Hyun

    2013-01-01

    Highlights: • Wall loss screening system (WalSS) has been developed based on ES-DCPD method. • Screening criteria was established based on the thinning of the actual shape that occur in the power plant. • With the criteria, the WalSS gives priority of the need for inspection. • This technique was successfully applied to commercial nuclear power plant. - Abstract: A new non-destructive evaluation (NDE) method has been developed for metal pipes for the detection wall thinning. The method has been showed to be suitable for applications to electric power generation plants where flow accelerated corrosion (FAC) of carbon steel piping is a significant cause of increased maintenance and plant personnel casualty. The wall thinning screening system (WalSS) was developed in two major phases. In the first phase, the equipotential switching direct current potential drop (ES-DCPD) method was developed for piping wall (Ryu et al., 2008a, 2010). In the second phase, in this paper, a quantitative detection criteria was developed. The relative ES-DCPD change of 3.8% has been defined as the screening criteria for wall thinning schematization. This criteria means that the component with measured ES-DCPD change greater than 3.8% is called for a more comprehensive examination. In the criteria development, all variables were taken into consideration based on commercial plant piping inspection data such as initial thickness distributions, wall thinning shape and nominal thickness. The developed WalSS based on ES-DCPD was applied to a moisture separator reheater (MSR) drain line of a commercial nuclear power plant (NPP) during a scheduled overhaul. The measured ES-DCPD change was 2.16%, which is lower than the ES-DCPD criteria, identifying the pipe having adequate wall thickness. This is confirmed by site thickness inspection using ultrasonic technique (UT)

  10. W-087 Acceptance test procedure. Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    Joshi, A.W.

    1997-06-10

    This Acceptance Test Procedure/Operational Test Procedure (ATP/OTP) has been prepared to demonstrate that the Electrical/Instrumentation and Mechanical systems function as required by project criteria and to verify proper operation of the integrated system including the interlocks.

  11. W-087 Acceptance test procedure. Revision 1

    International Nuclear Information System (INIS)

    Joshi, A.W.

    1997-01-01

    This Acceptance Test Procedure/Operational Test Procedure (ATP/OTP) has been prepared to demonstrate that the Electrical/Instrumentation and Mechanical systems function as required by project criteria and to verify proper operation of the integrated system including the interlocks

  12. An evaluation and acceptance of COTS software for FPGA-based controllers in NPPS

    International Nuclear Information System (INIS)

    Jung, Sejin; Kim, Eui-Sub; Yoo, Junbeom; Kim, Jang-Yeol; Choi, Jong Gyun

    2016-01-01

    Highlights: • All direct/indirect COTS SW should be dedicated. • FPGA synthesis tools are important for the safety of new digital I&Cs. • No standards/reports are yet available to deal with the indirect SW – FPGA synthesis tools. • This paper proposes a new evaluation/acceptance process and criteria for indirect SW. - Abstract: FPGA (Field-Programmable Gate Array) has received much attention from nuclear industry as an alternative platform of PLC (Programmable Logic Controller)-based digital I&C (Instrumentation & Control). Software aspect of FPGA development encompasses several commercial tools such as logic synthesis and P&R (Place & Route), which should be first dedicated in accordance with domestic standards based on EPRI NP-5652. Even if a state-of-the-art supplementary EPRI TR-1025243 makes an effort, the dedication of indirect COTS (Commercial Off-The-Shelf) SW such as FPGA logic synthesis tools has still caused a dispute. This paper proposes an acceptance process and evaluation criteria, specific to COTS SW, not commercial-grade direct items. It specifically incorporates indirect COTS SW and also provides categorized evaluation criteria for acceptance. It provides an explicit linkage between acceptance methods (Verification and Validation techniques) and evaluation criteria, too. We tried to perform the evaluation and acceptance process upon a commercial FPGA logic synthesis tool being used to develop a new FPGA-based digital I&C in Korea, and could confirm its applicability.

  13. Manufacturing and testing of reference samples for the definition of acceptance criteria for the ITER divertor

    International Nuclear Information System (INIS)

    Visca, Eliseo; Cacciotti, E.; Libera, S.; Mancini, A.; Pizzuto, A.; Roccella, S.; Riccardi, B.; Escourbiac, F.; Sanguinetti, G.P.

    2010-01-01

    The most critical part of a high heat flux (HHF) plasma facing component (PFC) is the armour to heat sink joint. An experimental study was launched by EFDA in order to define the acceptance criteria to be used for the procurements of the ITER Divertor PFCs. ENEA is involved in the European International Thermonuclear Experimental Reactor (ITER) R and D activities and together with Ansaldo Ricerche S.p.A. has manufactured several PFCs mock-ups using the Hot Radial Pressing and Pre-Brazed Casting technologies. According to the technical specifications issued by EFDA, ENEA and Ansaldo have collaborated to manufacture half of the samples with calibrated artificial defects required for this experimental study. After manufacturing, the samples were examined by ultrasonic and SATIR non-destructive examination (NDE) methods in order to confirm the size and position of the artificial defects. In particular, it was concluded that defects are detectable with these NDE techniques and they finally gave indication about the threshold of propagation during high heat flux experiments relevant with heat fluxes expected in ITER Divertor. This paper reports the manufacturing procedure used to obtain the required calibrated artificial defects in the CFC and W armoured samples as well as the NDE results and the thermal high heat flux results.

  14. Manufacturing and testing of reference samples for the definition of acceptance criteria for the ITER divertor

    Energy Technology Data Exchange (ETDEWEB)

    Visca, Eliseo, E-mail: visca@frascati.enea.i [Associazione EURATOM-ENEA sulla Fusione, Frascati (Italy); Cacciotti, E.; Libera, S.; Mancini, A.; Pizzuto, A.; Roccella, S. [Associazione EURATOM-ENEA sulla Fusione, Frascati (Italy); Riccardi, B., E-mail: Bruno.Riccardi@f4e.europa.e [Fusion For Energy, Barcelona (Spain); Escourbiac, F., E-mail: frederic.escourbiac@iter.or [ITER Organization, Cadarache (France); Sanguinetti, G.P., E-mail: gianpaolo.sanguinetti@aen.ansaldo.i [Ansaldo Energia S.p.A., Genova (Italy)

    2010-12-15

    The most critical part of a high heat flux (HHF) plasma facing component (PFC) is the armour to heat sink joint. An experimental study was launched by EFDA in order to define the acceptance criteria to be used for the procurements of the ITER Divertor PFCs. ENEA is involved in the European International Thermonuclear Experimental Reactor (ITER) R and D activities and together with Ansaldo Ricerche S.p.A. has manufactured several PFCs mock-ups using the Hot Radial Pressing and Pre-Brazed Casting technologies. According to the technical specifications issued by EFDA, ENEA and Ansaldo have collaborated to manufacture half of the samples with calibrated artificial defects required for this experimental study. After manufacturing, the samples were examined by ultrasonic and SATIR non-destructive examination (NDE) methods in order to confirm the size and position of the artificial defects. In particular, it was concluded that defects are detectable with these NDE techniques and they finally gave indication about the threshold of propagation during high heat flux experiments relevant with heat fluxes expected in ITER Divertor. This paper reports the manufacturing procedure used to obtain the required calibrated artificial defects in the CFC and W armoured samples as well as the NDE results and the thermal high heat flux results.

  15. The development of criteria for radioactive waste disposal

    International Nuclear Information System (INIS)

    Wagstaff, K.P.

    1985-02-01

    Radiation protection criteria are needed in Canada for judging the acceptability of radioactive waste disposal options for which there are potential long-term radiological impacts. This paper discusses the difficulties encountered in applying the ICRP system of dose limitation to the long term and the alternative approaches to criteria being developed and adopted by various other international and national bodies. Finally, the present situation in Canada is reviewed and conclusions are drawn on the general direction in which national criteria are being formulated and expressed

  16. A research for Class II defect Bored Pile’s Accept Criteria: A case of Penang Second Marine bridge

    Science.gov (United States)

    Huang, Kang

    2018-03-01

    The aim of this preliminary research is to study the accept criteria of class II bored pile with subtle defect. According to a detailed comparison of the existed different standards, Chinese ones are more applicable especially for the large diameter bored piles. Through the concrete coring at pile No P25-03 of this case and the comparison to the actual calculation, the Class II pile’s defects were very minor. Comparison was also made for the effects on pile structural capacities before and after repair of the defects. the feasible repair proposal may bring forward to more defects to the piles. The Class II piles don’t need any further repairation when piles have typical of similar character and sonic logging test result with P25-03‘s one. For other Class II piles with some differences in characters, verification is needed through further concrete coring on the pile. The recommendation of this research could be adopted for the similar huge marine structures which installed large diameter bored piles.

  17. Scientific opinion on the evaluation of substances as acceptable previous cargoes for edible fats and oils

    DEFF Research Database (Denmark)

    Petersen, Annette

    Shipping of edible fats and oils into Europe is permitted in bulk tanks, provided that the previous cargo is included in a positive list. The European Commission requested EFSA to evaluate the acceptability as previous cargoes for fats and oils the substances calcium lignosulphonate, methyl acetate...... the criteria for acceptability as previous cargoes. Due to uncertainties, mainly with regard to the composition and toxicity of the low molecular mass fraction, and the fact that the toxicological database is limited to the 40–65 grade and does not cover all grades of calcium lignosulphonate shipped...... as previous cargoes, the EFSA Panel on Contaminants in the Food Chain (CONTAM Panel) concluded that calcium lignosulphonate does not meet the criteria for acceptability as a previous cargo. Only food-grade ammonium sulphate meets the criteria for acceptability as a previous cargo due to uncertainties about...

  18. A STATISTICAL APPROACH FOR DERIVING KEY NFC EVALUATION CRITERIA

    Directory of Open Access Journals (Sweden)

    S.K. KIM

    2014-02-01

    As a result of analyzing the weight of evaluation criteria with the sample of nuclear power experts and the general public, both sides recognized safety as the most important evaluation criterion, and the social factors such as public acceptance appeared to be ranked as more important evaluation criteria by the nuclear energy experts than the general public.

  19. Extended BRS algebra and color confinement criteria

    International Nuclear Information System (INIS)

    Shintani, Meiun.

    1983-09-01

    We examine the color-confinement criteria proposed by Kugo and Ojima. With the use of the extended BRS symmetry and the Nakanishi's theorem, we look for the representations of the BRS algebra compatible with the first condition of their criteria (the K-O condition) and then ask whether or not they are physically acceptable. As a result, the quartet mechanism does not work, and the K-O condition is not regarded as a confinement condition. (author)

  20. Study of Validity Criteria for Radionuclide-Analysis of Low- and Intermediate-Level Radioactive Waste

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ji Uk; Baek, Hyun Suk; Jeong, Sung Yeop [Sungwoo E and T Co., Hanam (Korea, Republic of); Shin, Seung Kyu [Korea Radioactive waste Management Corporation, Gyeongju (Korea, Republic of)

    2013-05-15

    Literature survey on the deviation of the measuring equipment and statistical analysis on the measured data of domestic LILW were performed in order to set evaluation criteria quantitatively when comparing the result of each test and inspections. This study provided opportunity to increase credibility and re-assure validity of Waste Acceptance Criteria (WAC). Through the statistical analysis for deviation of measurement by comparing repository inspection with generator self-test, the quantitative acceptance criteria were set depending on specific activity of Co-60 and Cs-137. The acceptance criteria is a relative bias of KRMC result to generator result and set from low 50 % to high 150 % for Co-60, from low 30 % to 250 % for Cs-137. In this study, because the statistical analysis results of the waste drum assay are not enough representing whole range specified at WAC, an additional research that include characteristic analysis of LILW generated other birthplace should be done.

  1. On the approximation of the optically thin layer in plasma spectroscopy

    International Nuclear Information System (INIS)

    Preobrazhensky, N.G.

    1975-01-01

    Recent studies are described of criteria for the optically thin approximation relevant to more reliable interpretation of various plasma spectroscopic measurements. Non-equilibrium situations are in the focus of attention. Applicability of well-known criteria suggested by McWhirter and Hearn is outlined. (Auth.)

  2. Criteria for decommissioning

    International Nuclear Information System (INIS)

    Ricci, P.F.

    1988-01-01

    In this paper the authors describe three risk acceptability criteria as parts of a strategy to clean up decommissioned facilities, related to both the status quo and to a variety of alternative technical clean-up options. The acceptability of risk is a consideration that must enter into any decision to establish when a site is properly decommissioned. To do so, both the corporate and public aspects of the acceptability issue must be considered. The reasons for discussion the acceptability of risk are to: Legitimize the process for making cleanup decisions; Determine who is at risk, who benefits, and who bears the costs of site cleanup, for each specific cleanup option, including the do nothing option; Establish those factors that, taken as a whole, determine measures of acceptability; Determine chemical-specific aggregate and individual risk levels; and Establish levels for cleanup. The choice of these reasons is pragmatic. The method consistent with these factors is risk-risk-effectiveness: the level of cleanup must be consistent with the foreseeable use of the site and budget constraints. Natural background contamination is the level below which further cleanup is generally inefficient. Case-by-case departures from natural background are to be considered depending on demonstrated risk. For example, a hot spot is obviously a prima facie exception, but should be rebuttable. Rebuttability means that, through consensus, the ''hot spot'' is shown not to be associated with exposure

  3. Development of very low-level radioactive waste sequestration process criteria

    Energy Technology Data Exchange (ETDEWEB)

    Chan, N.; Wong, P., E-mail: nicholas.chan@cnl.ca [Canadian Nuclear Laboratories, Chalk River, Ontario (Canada)

    2015-12-15

    Segregating radioactive waste at the source and reclassifying radioactive waste to lower waste classes are the key activities to reduce the environmental footprint and long-term liability. In the Canadian Standards Association's radioactive waste classification system, there are 2 sub-classes within low-level radioactive waste: very short-lived radioactive waste and very low-level radioactive waste (VLLW). VLLW has a low hazard potential but is above the Canadian unconditional clearance criteria as set out in Schedule 2 of Nuclear Substances and Devices Regulations. Long-term waste management facilities for VLLW do not require a high degree of containment and isolation. In general, a relatively low-cost near-surface facility with limited regulatory control is suitable for VLLW. At Canadian Nuclear Laboratories' Chalk River Laboratories site an initiative, VLLW Sequestration, was implemented in 2013 to set aside potential VLLW for temporary storage and to be later dispositioned in the planned VLLW facility. As of May 2015, a total of 236m{sup 3} resulting in approximately $1.1 million in total savings have been sequestered. One of the main hurdles in implementing VLLW Sequestration is the development of process criteria. Waste Acceptance Criteria (WAC) are used as a guide or as requirements for determining whether waste is accepted by the waste management facility. Establishment of the process criteria ensures that segregated waste materials have a high likelihood to meet the VLLW WAC and be accepted into the planned VLLW facility. This paper outlines the challenges and various factors which were considered in the development of interim process criteria. (author)

  4. Environmental risk assessment: its contribution to criteria development for HLW disposal

    International Nuclear Information System (INIS)

    Smith, G.M.; Little, R.H.; Watkins, B.M.

    1999-01-01

    Principles for radioactive waste management have been provided by the International Atomic Energy Agency in Safety Series No.111-F, which was published in 1995. This has been a major step forward in the process of achieving acceptance for proposals for disposal of radioactive waste, for example, for High Level Waste disposal in deep repositories. However, these principles have still to be interpreted and developed into practical radiation protection criteria. Without prejudicing final judgements on the acceptability of waste proposals, an important aspect is that practical demonstration of compliance (or the opposite) with these criteria must be possible. One of the IAEA principles requires that radioactive waste shall be managed in such a way as to provide an acceptable level of protection of the environment. There has been and continues to be considerable debate as to how to demonstrate compliance with such a principle. This paper briefly reviews the current status and considers how experience in other areas of environmental protection could contribute to criteria development for HLW disposal

  5. Management alternatives of energy wood thinning stands

    International Nuclear Information System (INIS)

    Heikkilae, Jani; Siren, Matti; Aeijaelae, Olli

    2007-01-01

    Energy wood thinning has become a feasible treatment alternative of young stands in Finland. Energy wood thinnings have been carried out mainly in stands where precommercial thinning has been neglected and the harvesting conditions for industrial wood thinning are difficult. Despite of its positive effects on harvesting costs and on renewable energy potential, whole-tree harvesting has been constantly criticized for causing growth loss. In this paper, the profitability of energy wood thinning was studied in 20 Scots pine-dominated stands where energy wood thinning was carried out. The growth of the stands after thinning was predicted with the help of Motti-stand simulator. Entire rotation time of the stands was simulated with different management alternatives. The intensity of first thinning and recovery level of logging residues varied between alternatives. In order to attain acceptable harvesting conditions, industrial wood thinning had to be delayed. The effect of energy wood thinning on subsequent stem wood growth was almost the same as in conventional thinning. Whole-tree harvesting for energy proved to be profitable alternative if the stumpage price is around 3EUR m -3 , the interest rate is 3% or 5% and the removal of pulpwood is less than 20 m 3 ha -1 . If the harvestable pulpwood yield is over 20 m 3 ha -1 , integrated harvesting of industrial and energy wood or delayed industrial wood harvesting becomes more profitable. (author)

  6. Plugging criteria for WWER SG tubes

    Energy Technology Data Exchange (ETDEWEB)

    Papp, L.; Wilam, M. [Vitkovice NPP Services (Switzerland); Herman, M. [Vuje, Trnava (Slovakia)

    1997-12-31

    At operated Czech and Slovak nuclear power plants the 80 % criteria for crack or other bulk defect depth is used for steam generator heat exchanging tubes plugging. This criteria was accepted as the recommendation of designer of WWER steam generators. Verification of this criteria was the objective of experimental program performed by Vitkovice, J.S.C., UJV Rez, J.S.C. and Vuje Trnava, J.S.C .. Within this program the following factors were studied: (1) Influence of secondary water chemistry on defects initiation and propagation, (2) Statistical evaluation of corrosion defects progression at operated SG, and (3) Determination of critical pressure for tube rupture as a function of eddy current indications. In this presentation items (2) and (3) are considered.

  7. Plugging criteria for WWER SG tubes

    Energy Technology Data Exchange (ETDEWEB)

    Papp, L; Wilam, M [Vitkovice NPP Services (Switzerland); Herman, M [Vuje, Trnava (Slovakia)

    1998-12-31

    At operated Czech and Slovak nuclear power plants the 80 % criteria for crack or other bulk defect depth is used for steam generator heat exchanging tubes plugging. This criteria was accepted as the recommendation of designer of WWER steam generators. Verification of this criteria was the objective of experimental program performed by Vitkovice, J.S.C., UJV Rez, J.S.C. and Vuje Trnava, J.S.C .. Within this program the following factors were studied: (1) Influence of secondary water chemistry on defects initiation and propagation, (2) Statistical evaluation of corrosion defects progression at operated SG, and (3) Determination of critical pressure for tube rupture as a function of eddy current indications. In this presentation items (2) and (3) are considered.

  8. Acceptance of spent fuel of varying characteristics

    International Nuclear Information System (INIS)

    Short, S.M.

    1990-03-01

    This paper is a preliminary overview of a study with the primary objective of establishing a set of acceptance selection criteria and corresponding spent fuel characteristics to be incorporated as a component of requirements for the Federal Waste Management System (FWMS). A number of alternative acceptance allocations and selection rules were analyzed to determine the operational sensitivity of each element of the FWMS to the resultant spent fuel characteristics. Preliminary recommendations of the study include three different sets of selection rules to be included in the FWMS design basis. 2 refs., 4 figs., 4 tabs

  9. Optical response of thin amorphous films to infrared radiation

    Science.gov (United States)

    Orosco, J.; Coimbra, C. F. M.

    2018-03-01

    We briefly review the electrical-optical response of materials to radiative forcing within the formalism of the Kramers-Kronig relations. A commensurate set of criteria is described that must be met by any frequency-domain model representing the time-domain response of a real (i.e., physically possible) material. The criteria are applied to the Brendel-Bormann (BB) oscillator, a model that was originally introduced for its fidelity at reproducing the non-Lorentzian peak broadening experimentally observed in the infrared absorption by thin amorphous films but has since been used for many other common materials. We show that the BB model fails to satisfy the established physical criteria. Taking an alternative approach to the model derivation, a physically consistent model is proposed. This model provides the appropriate line-shape broadening for modeling the infrared optical response of thin amorphous films while adhering strictly to the Kramers-Kronig criteria. Experimental data for amorphous alumina (Al2O3 ) and amorphous quartz silica (SiO2) are used to obtain model parametrizations for both the noncausal BB model and the proposed causal model. The proposed model satisfies consistency criteria required by the underlying physics and reproduces the experimental data with better fidelity (and often with fewer parameters) than previously proposed permittivity models.

  10. [Organization of socially acceptable working hours in nursing].

    Science.gov (United States)

    Büssing, A; Glaser, J

    1994-05-01

    Three dimensions in the structure of the working hour system of nurses, rendering them socially acceptable, are becoming important: duration of the working day, the time of day which is being worked and the distribution of working hours. The latter two are of particular importance because flexible shift is becoming the dominant pattern in nursing. Six indicators are discussed as criteria for social acceptability: security of employment which includes access to the labour-market, level of income, health, opportunity for social relationships, social participation, and autonomy. Responses of 297 nurses in one General Hospital taking part in a study, were analysed to examine empirically the concept of 'socially acceptable structure of the working hours'. Ideal and factual patterns are considered first. Secondly aspects of autonomy are considered and the way this depends on time, thirdly the criteria used to define 'social acceptability' are examined for validity. Results show firstly the cross contrast between the hospital's expectation and the nurses' wishes with regard to working hours. Furthermore, inspite of the demand for flexibility, staff have very little choice and there is little sign of joint decision making. Thirdly results show that health, interpersonal and social aspects are of special importance and that, correspondingly, in the view of nurses, financial and practical problems are of lesser importance in their every day life.

  11. How forest context influences the acceptability of prescribed burning and mechanical thinning

    Science.gov (United States)

    Alan D. Bright; Peter Newman

    2006-01-01

    We examined how forest factors influenced public perceptions of three fuels management alternatives: prescribed burns, mechanical thinning, or no artificial fire management. The factors included the forest?s proximity to urban areas, primary use, wildfire history, and current fire conditions. Surveying three study strata with different wildfire histories and...

  12. Selection criteria of residents for residency programs in Kuwait.

    Science.gov (United States)

    Marwan, Yousef; Ayed, Adel

    2013-01-19

    In Kuwait, 21 residency training programs were offered in the year 2011; however, no data is available regarding the criteria of selecting residents for these programs. This study aims to provide information about the importance of these criteria. A self-administered questionnaire was used to collect data from members (e.g. chairmen, directors, assistants …etc.) of residency programs in Kuwait. A total of 108 members were invited to participate. They were asked to rate the importance level (scale from 1 to 5) of criteria that may affect the acceptance of an applicant to their residency programs. Average scores were calculated for each criterion. Of the 108 members invited to participate, only 12 (11.1%) declined to participate. Interview performance was ranked as the most important criteria for selecting residents (average score: 4.63/5.00), followed by grade point average (average score: 3.78/5.00) and honors during medical school (average score: 3.67/5.00). On the other hand, receiving disciplinary action during medical school and failure in a required clerkship were considered as the most concerning among other criteria used to reject applicants (average scores: 3.83/5.00 and 3.54/5.00 respectively). Minor differences regarding the importance level of each criterion were noted across different programs. This study provided general information about the criteria that are used to accept/reject applicants to residency programs in Kuwait. Future studies should be conducted to investigate each criterion individually, and to assess if these criteria are related to residents' success during their training.

  13. Project W-049H Collection System Acceptance Test

    International Nuclear Information System (INIS)

    Buckles, D.I.

    1994-01-01

    The Acceptance Test Procedure (ATP) Program for Project W-049H covers the following activities: Disposal system, Collection system, Instrumentation and control system. Each activity has its own ATP. The purpose of the ATPs is to verify that the systems have been constructed in accordance with the construction documents and to demonstrate that the systems function as required by the Project criteria. This ATP has been prepared to demonstrate that the Collection System Instrumentation functions as required by project criteria

  14. Measurement methodology for fulfilling of waste acceptance criteria for low and intermediate level radioactive waste in storages - 59016

    International Nuclear Information System (INIS)

    Sokcic-Kostic, M.; Langer, F.; Schultheis, R.

    2012-01-01

    Low and intermediate level radioactive waste must be sorted and treated before it can be sent to radioactive waste storage. The waste must fulfil an extensive amount of acceptance criteria (WAC) to guarantee a safe storage period. NUKEM Technologies has a broad experience with the building and management of radioactive waste treatment facilities and has developed methods and equipment to produce the waste packages and to gather all the required information. In this article we consider low and intermediate level radioactive waste excluding nuclear fuel material, even fresh fuel with low radiation. Only solid radioactive waste (RAW) will be considered. (Liquid RAW is usually processed and solidified before storage. Exception is the reprocessing of nuclear fuel.) Low and intermediate level radioactive waste has to be kept in storage facilities until isotopes are decayed sufficiently and the waste can be released. The storage has to fulfil certain conditions regarding the possible radiological impact and the possible chemical impact on the environment. With the inventory of nuclear waste characterised, the radiological impact can be estimated. RAW mainly originates from the operation of nuclear power plants. A small amount comes from reprocessing installations or from research entities. Chemical safety aspects are of qualitative nature, excluding substances in whole but not compared to limit values. Therefore they have minor influence on the storage conditions. Hereby corrosion and immobilisation of the waste play important roles. The storage concept assumes that the waste will be released if the radioactivity has decreased to an acceptable level. NUKEM Technologies has been specialised on collecting all data needed for the fulfilling of waste acceptance criteria (WAC). The classification as low or intermediate level waste is made on base of surface dose rate of the waste package as well as on the mass specific beta activity. Low level waste must not include isotopes

  15. Multi criteria analysis in the renewable energy industry

    CERN Document Server

    San Cristóbal Mateo, José Ramón

    2012-01-01

    Decision makers in the Renewable Energy sector face an increasingly complex social, economic, technological, and environmental scenario in their decision process. Different groups of decision-makers become involved in the process, each group bringing along different criteria therefore, policy formulation for fossil fuel substitution by Renewable Energies must be addressed in a multi-criteria context. Multi Criteria Analysis in the Renewable Energy Industry is a direct response to the increasing interest in the Renewable Energy industry which can be seen as an important remedy to many environmental problems that the world faces today. The multiplicity of criteria and the increasingly complex social, economic, technological, and environmental scenario makes multi-criteria analysis a valuable tool in the decision-making process for fossil fuel substitution. The detailed chapters explore the use of the Multi-criteria decision-making methods and how they provide valuable assistance in reaching equitable and accept...

  16. Criteria for safety-related operator actions

    International Nuclear Information System (INIS)

    Gray, L.H.; Haas, P.M.

    1983-01-01

    The Safety-Related Operator Actions (SROA) Program was designed to provide information and data for use by NRC in assessing the performance of nuclear power plant (NPP) control room operators in responding to abnormal/emergency events. The primary effort involved collection and assessment of data from simulator training exercises and from historical records of abnormal/emergency events that have occurred in operating plants (field data). These data can be used to develop criteria for acceptability of the use of manual operator action for safety-related functions. Development of criteria for safety-related operator actions are considered

  17. Effects of emotional acceptance and rumination on media-induced body dissatisfaction in anorexia and bulimia nervosa.

    Science.gov (United States)

    Naumann, Eva; Tuschen-Caffier, Brunna; Voderholzer, Ulrich; Schäfer, Johanna; Svaldi, Jennifer

    2016-11-01

    Body dissatisfaction is an important risk and maintaining factor for eating disorders. The aim of the present study was to experimentally test the effects of two emotion regulation strategies - acceptance and rumination - on media-induced body dissatisfaction in eating disorders. After watching pictures of thin models, women with anorexia nervosa (AN; n = 39) and bulimia nervosa (BN; n = 39) were encouraged to either use emotional acceptance or rumination to cope with their feelings. Body dissatisfaction and mood were repeatedly assessed. Acceptance significantly improved body dissatisfaction in women with BN. Rumination led to a significant increase of body dissatisfaction in both eating disorder groups. Results were independent from mood changes. Findings highlight the importance ruminative thinking may have in the aggravation of dissatisfaction with the own body in AN and BN. Results suggest that emotional acceptance is a useful strategy to regulate body dissatisfaction after exposure to thin-ideal media in BN. Copyright © 2016 Elsevier Ltd. All rights reserved.

  18. A small-angle large-acceptance detection system for hadrons

    Science.gov (United States)

    Kalantar-Nayestanaki, N.; Bacelar, J. C. S.; Brandenburg, S.; Huisman, H.; Messchendorp, J. G.; Mul, F. A.; Schadmand, S.; van der Schaaf, K.; Schippers, J. M.; Volkerts, M.

    2000-04-01

    The performance of a segmented large-acceptance detector, capable of measuring particles at small forward angles, is presented. The Small-Angle Large-Acceptance Detector (SALAD), was built to handle very high rates of particles impinging on the detector. Particles down to a few MeV can be detected with it. The position of charged particles is measured by two Multi-Wire Proportional Chambers while scintillator blocks are used to measure the energy of the detected particle. A stack of thin scintillators placed behind the energy detectors allows for a hardware rejection (veto) of high-energy particles going through the scintillator blocks.

  19. A small-angle large-acceptance detection system for hadrons

    CERN Document Server

    Kalantar-Nayestanaki, N; Brandenburg, S; Huisman, H; Messchendorp, J G; Mul, F A; Schadmand, S; Schaaf, K V D; Schippers, J M; Volkerts, M

    2000-01-01

    The performance of a segmented large-acceptance detector, capable of measuring particles at small forward angles, is presented. The Small-Angle Large-Acceptance Detector (SALAD), was built to handle very high rates of particles impinging on the detector. Particles down to a few MeV can be detected with it. The position of charged particles is measured by two Multi-Wire Proportional Chambers while scintillator blocks are used to measure the energy of the detected particle. A stack of thin scintillators placed behind the energy detectors allows for a hardware rejection (veto) of high-energy particles going through the scintillator blocks.

  20. A small-angle large-acceptance detection system for hadrons

    International Nuclear Information System (INIS)

    Kalantar-Nayestanaki, N.; Bacelar, J.C.S.; Brandenburg, S.; Huisman, H.; Messchendorp, J.G.; Mul, F.A.; Schadmand, S.; Schaaf, K. van der; Schippers, J.M.; Volkerts, M.

    2000-01-01

    The performance of a segmented large-acceptance detector, capable of measuring particles at small forward angles, is presented. The Small-Angle Large-Acceptance Detector (SALAD), was built to handle very high rates of particles impinging on the detector. Particles down to a few MeV can be detected with it. The position of charged particles is measured by two Multi-Wire Proportional Chambers while scintillator blocks are used to measure the energy of the detected particle. A stack of thin scintillators placed behind the energy detectors allows for a hardware rejection (veto) of high-energy particles going through the scintillator blocks

  1. The leak before break criteria, requirements and implications

    International Nuclear Information System (INIS)

    Martinez M, E.

    1992-05-01

    Inside this work a general balance is made on the Leak before break approach (LBB), like they are the history and licensing, those limitations, the acceptance criteria of the LBB, the current state of the regulatory development and the current state of it application in countries like E.U.A, Germany, Canada, Italy and France. Everything it with the purpose of evaluating the opportunities that offers the LBB criteria for it possible application in Mexico. (Author)

  2. Technical evaluation of draft ANSI Standard N13.30, ''performance criteria for radiobioassay''

    International Nuclear Information System (INIS)

    MacLellan, J.A.; Traub, R.J.

    1986-03-01

    The Pacific Northwest Laboratory (PNL) is conducting a research program to evaluate the appropriateness of criteria in the ANSI draft Standard N13.30, ''Performance Criteria for Radiobioassay.'' The evaluation has progressed parallel with the preparation of the Standard by evaluating the performance of existing bioassay laboratories against the criteria specified. Recommendations for revision of the Standard and implementation of a testing/accreditation program have been formulated based on study results. The current performance testing program includes both in-vivo counting and in-vitro sample measurements. Test criteria specified in the Standard include relative bias, relative precision, and acceptable minimum detectable activity (AMDA). Results to date have indicated that the acceptance criteria in the Standard are appropriate for the existing state of the industry and are achievable by a majority of the participating laboratories. Specific conclusions are that the AMDA criteria are most difficult for the laboratories to achieve; the relative bias criterion is second in difficulty, and the precision criterion presents no problem for the laboratories; most of the participating laboratories can meet the Standard; and failure rates may decrease as the laboratories become more knowledgeable of the performance criteria. 3 refs., 11 figs., 6 tabs

  3. [Revision of McDonald's new diagnostic criteria for multiple sclerosis].

    Science.gov (United States)

    Wiendl, H; Kieseier, B C; Gold, R; Hohlfeld, R; Bendszus, M; Hartung, H-P

    2006-10-01

    In 2001, an international panel suggested new diagnostic criteria for multiple sclerosis (MS). These criteria integrate clinical, imaging (MRI), and paraclinical results in order to facilitate diagnosis. Since then, these so-called McDonald criteria have been broadly accepted and widely propagated. In the meantime a number of publications have dealt with the sensitivity and specificity for MS diagnosis and with implementing these new criteria in clinical practice. Based on these empirical values and newer data on MS, an international expert group recently proposed a revision of the criteria. Substantial changes affect (1) MRI criteria for the dissemination of lesions over time, (2) the role of spinal cord lesions in the MRI and (3) diagnosis of primary progressive MS. In this article we present recent experiences with the McDonald and revised criteria.

  4. Acceptance test procedure for High Pressure Water Jet System

    International Nuclear Information System (INIS)

    Crystal, J.B.

    1995-01-01

    The overall objective of the acceptance test is to demonstrate a combined system. This includes associated tools and equipment necessary to perform cleaning in the 105 K East Basin (KE) for achieving optimum reduction in the level of contamination/dose rate on canisters prior to removal from the KE Basin and subsequent packaging for disposal. Acceptance tests shall include necessary hardware to achieve acceptance of the cleaning phase of canisters. This acceptance test procedure will define the acceptance testing criteria of the high pressure water jet cleaning fixture. The focus of this procedure will be to provide guidelines and instructions to control, evaluate and document the acceptance testing for cleaning effectiveness and method(s) of removing the contaminated surface layer from the canister presently identified in KE Basin. Additionally, the desired result of the acceptance test will be to deliver to K Basins a thoroughly tested and proven system for underwater decontamination and dose reduction. This report discusses the acceptance test procedure for the High Pressure Water Jet

  5. Retrospective analysis of 'gamma distribution' based IMRT QA criteria

    International Nuclear Information System (INIS)

    Wen, C.; Chappell, R.A.

    2010-01-01

    Full text: IMRT has been implemented into clinical practice at Royal Hobart Hospital (RHH) since mid 2006 for treating patients with Head and Neck (H and N) or prostate tumours. A local quality assurance (QA) acceptance criteria based on 'gamma distribution' for approving IMRT plan was developed and implemented in early 2007. A retrospective analysis of such criteria over 194 clinical cases will be presented. The RHH IMRT criteria was established with assumption that gamma distribution obtained through inter-comparison of 2 D dose maps between planned and delivered was governed by a positive-hail' normal distribution. A commercial system-MapCheck was used for 2 D dose map comparison with a built-in gamma analysis tool. Gamma distribution histogram was generated and recorded for all cases. By retrospectively analysing those distributions using curve fitting technique, a statistical gamma distribution can be obtained and evaluated. This analytical result can be used for future IMRT planing and treatment delivery. The analyses indicate that gamma distribution obtained through MapCheckTM is well under the normal distribution, particularly for prostate cases. The applied pass/fail criteria is not overly sensitive to identify 'false fails' but can be further tighten-up for smaller field while for larger field found in both H and N and prostate cases, the criteria was correctly applied. Non-uniform distribution of detectors in MapCheck and experience level of planners are two major factors to variation in gamma distribution among clinical cases. This criteria derived from clinical statistics is superior and more accurate than single-valued criteria for lMRT QA acceptance procedure. (author)

  6. Acceptable Knowledge Summary Report for Waste Stream: SR-T001-221F-HET/Drums

    International Nuclear Information System (INIS)

    Lunsford, G.F.

    1999-01-01

    This report is fully responsive to the requirements of Section 4.0 ''Acceptable Knowledge'' from the WIPP Transuranic Waste Characterization Quality Assurance Plan, CAO-94-1010, and provides a sound, (and auditable) characterization that satisfies the WIPP criteria for Acceptable Knowledge

  7. Mark II containment lead plant program load evaluation and acceptance criteria

    International Nuclear Information System (INIS)

    1978-10-01

    The report, prepared by the Office of Nuclear Reactor Regulation, addresses the portion of the Mark II owner's program that provides a generic methodology for establishing design basis LOCA and safety relief valve loads for the lead Mark II facilities (Zimmer, Shoreham, and LaSalle), i.e., the lead plant program. The report includes an evaluation of the Mark II owner's load methodology, a description of load methodologies that we find acceptable for use in the individual plant unique assessments, and the basis for the stated conclusions

  8. Early Site Permit Demonstration Program: Regulatory criteria evaluation report

    International Nuclear Information System (INIS)

    1993-03-01

    The primary objective of the Early Site Plan Demonstration Program (ESPDP) is to demonstrate successfully the use of 10CFR52 to obtain ESPs for one or more US sites for one (or more) ALWR nuclear power plants. It is anticipated that preparation of the ESP application and interaction with NRC during the application review process will result not only in an ESP for the applicant(s) but also in the development of criteria and definition of processes, setting the precedent that facilitates ESPs for subsequent ESP applications. Because siting regulatory processes and acceptance criteria are contained in over 100 separate documents, comprehensive licensing and technical reviews were performed to establish whether the requirements and documentation are self-consistent, whether the acceptance criteria are sufficiently well-defined and clear, and whether the licensing process leading to the issuance of an ESP is unambiguously specified. This document provides appendices C and D of this report. Appendix C contains data from the licensing and technical reviews; Appendix D contains technology toolkit data sheets

  9. Muscle dysmorphia: a critical review of the proposed criteria.

    Science.gov (United States)

    Chung, B

    2001-01-01

    While body-image related disorders such as anorexia nervosa have focused on thinness, only recently have clinical criteria for a disorder that centers around muscularity--muscle dysmorphia--been proposed. An individual affected by muscle dysmorphia is overly concerned with his or her degree of muscularity. This preoccupation is manifested in the individual's behavior (excessive weight lifting, excessive attention to diet, social impairment). This article examines the historical aspects and proposed criteria for muscle dysmorphia and contrasts them with those of anorexia nervosa. While the authors of the proposed criteria have suggested that muscle dysmorphia be classified as a subcategory of body dysmorphic disorder, both the historical and clinical aspects of this syndrome are more consistent with its classification as an obsessive-compulsive disorder.

  10. Electrostatic bonding of thin (cycle sine 3 mil) 7070 cover glass to Ta2O5 AR-coated thin (cycle sine 2 mil) silicon wafers and solar cells

    Science.gov (United States)

    Egelkrout, D. W.

    1981-01-01

    Electrostatic bonding of thin cover glass to thin solar cells was researched. Silicon solar cells, wafers, and Corning 7070 glass of from about 0.002" to about 0.003" in thickness were used in the investigation to establish optimum parameters for producing mechanically acceptable bonds while minimizing thermal stresses and resultant solar cell electrical parameter degradation.

  11. Minimizing Experimental Error in Thinning Research

    Science.gov (United States)

    C. B. Briscoe

    1964-01-01

    Many diverse approaches have been made prescribing and evaluating thinnings on an objective basis. None of the techniques proposed hasbeen widely accepted. Indeed. none has been proven superior to the others nor even widely applicable. There are at least two possible reasons for this: none of the techniques suggested is of any general utility and/or experimental error...

  12. Waste acceptance product specifications for vitrified high-level waste forms

    International Nuclear Information System (INIS)

    Applewhite-Ramsey, A.; Sproull, J.F.

    1994-01-01

    The Department of Energy (DOE) Office of Environmental Restoration and Waste Management (EM) has developed Waste Acceptance Product Specifications (EM-WAPS). The EM-WAPS will be the basis for defining product acceptance criteria compatible with the requirements of the Civilian Radioactive Waste Management System (CRWMS). The relationship between the EM-WAPS and the CRWMS Systems Requirements document (WA-SRD) will be discussed. The impact of the EM-WAPS on the Savannah River Sit (SRS) Defense Waste Processing Facility's (DWPF) Waste Acceptance Program, Waste Qualification Run planning, and startup schedule will also be reported. 14 refs., 2 tabs

  13. Considerations for developing seismic design criteria for nuclear waste storage repositories

    International Nuclear Information System (INIS)

    Owen, G.N.; Yanev, P.I.; Scholl, R.E.

    1980-04-01

    The function of seismic design criteria is to reduce the potential for hazards that may arise during various stages of the repository life. During the operational phase, the major concern is with the possible effects of earthquakes on surface facilities, underground facilities, and equipment. During the decommissioned phase, the major concern is with the potential effects of earthquakes on the geologic formation, which may result in a reduction in isolation capacity. Existing standards and guides or criteria used for the static and seismic design of licensed nuclear facilities were reviewed and evaluated for their applicability to repository design. This report is directed mainly toward the development of seismic design criteria for the underground structures of repositories. An initial step in the development of seismic design criteria for the underground structures of repositories is the development of performance criteria, or minimum standards of acceptable behavior. A number of possible damage modes are identified for the operating phase of the repository; however, no damage modes are foreseen that would perturb the long-term function of the repository, except for the possibility of increased permeability within the rock mass. Subsequent steps in formulating acceptable seismic design criteria for the underground structures involve the quantification of the design process. The report discusses the necessity of specifying the form of ground motion that would be needed for seismic analysis and the procedures that may be used for making ground motion predictions. Further discussions outline what is needed for analysis, including rock properties, failure criteria, modeling techniques, seismic hardening criteria for the host rock mass, and probabilistic considerations

  14. FFTBM and primary pressure acceptance criterion

    International Nuclear Information System (INIS)

    Prosek, A.

    2004-01-01

    When thermalhydraulic computer codes are used for simulation in the area of nuclear engineering the question is how to conduct an objective comparison between the code calculation and measured data. To answer this the fast Fourier transform based method (FFTBM) was developed. When the FFTBM method was developed the acceptance criteria for primary pressure and total accuracy were set. In the recent study the FFTBM method was used for accuracy quantification of RD-14M large LOCA test B9401 calculations. The blind accuracy analysis indicated good total accuracy while the primary pressure criterion was not fulfilled. The objective of the study was therefore to investigate the reasons for not fulfilling the primary pressure acceptance criterion and the applicability of the criterion to experimental facilities simulating heavy water reactor. The results of the open quantitative analysis showed that sensitivity analysis for influence parameters provide sufficient information to judge in which calculation the accuracy of primary pressure is acceptable. (author)

  15. Qualification criteria to certify a package for air transport of plutonium

    International Nuclear Information System (INIS)

    1977-12-01

    The document describes qualification criteria developed by the U.S. Nuclear Regulatory Commission to certify a package for air transport of plutonium. Included in the document is a discussion of aircraft accident conditions and a summary of the technical basis for the qualification criteria. The criteria require prototype packages to be subjected to various individual and sequential tests that simulate the conditions produced in severe aircraft accidents. Specific post-test acceptance standards are prescribed for each of the three safety functions of a package. The qualification criteria also prescribe certain operational controls to be exercised during transport

  16. Preliminary estimates of the impacts of alternative spent fuel acceptance rates

    International Nuclear Information System (INIS)

    Clark, L.L.; McKee, R.W.; Short, S.M.

    1986-02-01

    The rate at which spent fuel is accepted by the federal waste management system is an important interface between the private nuclear power sector and the federal government, which will assume responsibility for spent fuel disposal. An analysis of alternative rates based on minimum age criteria indicates substantial incentives to limit acceptance rates so as to result in minimum 10 to 15 year fuel ages for repository acceptance [1500 to 2500 metric tons of uranium (MTU) per year]. These incentives include lower heat generation rates and systems costs

  17. A Statistical Approach for Deriving Key NFC Evaluation Criteria

    Energy Technology Data Exchange (ETDEWEB)

    Kim, S. K; Kang, G. B.; Ko, W. I [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Young, S. R.; Gao, R. X. [Univ. of Science and Technology, Daejeon (Korea, Republic of)

    2014-02-15

    This study suggests 5 evaluation criteria (safety and technology, environmental impact, economic feasibility, social factors, and institutional factors) and 24 evaluation indicators for a NFC (nuclear fuel cycle) derived using factor analysis. To do so, a survey using 1 on 1 interview was given to nuclear energy experts and local residents who live near nuclear power plants. In addition, by conducting a factor analysis, homogeneous evaluation indicators were grouped with the same evaluation criteria, and unnecessary evaluation criteria and evaluation indicators were dropped out. As a result of analyzing the weight of evaluation criteria with the sample of nuclear power experts and the general public, both sides recognized safety as the most important evaluation criterion, and the social factors such as public acceptance appeared to be ranked as more important evaluation criteria by the nuclear energy experts than the general public.

  18. A Statistical Approach for Deriving Key NFC Evaluation Criteria

    International Nuclear Information System (INIS)

    Kim, S. K; Kang, G. B.; Ko, W. I; Young, S. R.; Gao, R. X.

    2014-01-01

    This study suggests 5 evaluation criteria (safety and technology, environmental impact, economic feasibility, social factors, and institutional factors) and 24 evaluation indicators for a NFC (nuclear fuel cycle) derived using factor analysis. To do so, a survey using 1 on 1 interview was given to nuclear energy experts and local residents who live near nuclear power plants. In addition, by conducting a factor analysis, homogeneous evaluation indicators were grouped with the same evaluation criteria, and unnecessary evaluation criteria and evaluation indicators were dropped out. As a result of analyzing the weight of evaluation criteria with the sample of nuclear power experts and the general public, both sides recognized safety as the most important evaluation criterion, and the social factors such as public acceptance appeared to be ranked as more important evaluation criteria by the nuclear energy experts than the general public

  19. Preliminary waste acceptance requirements for the planned Konrad repository

    International Nuclear Information System (INIS)

    Warnecke, E.; Brennecke, P.

    1987-01-01

    The Physikalisch-Technische Bundesanstalt (PTB) has established Preliminary Waste Acceptance Requirements for the planned Konrad repository. These requirements were developed, in accordance with the Safety Criteria of the Reactor Safety Commission, with the help of a site specific safety assessment; they are under the reservation of the plan approval procedure, which is still in progress. In developing waste acceptance requirements, the PTB fulfills one of its duties as the institute responsible for waste disposal and gives guidelines for waste conditioning to waste producers and conditioners. (orig.) [de

  20. A Systematic Review of Patient Acceptance of Consumer Health Information Technology

    OpenAIRE

    Karsh, BT; Or, CKL

    2009-01-01

    A systematic literature review was performed to identify variables promoting consumer health information technology (CHIT) acceptance among patients. The electronic bibliographic databases Web of Science, Business Source Elite, CINAHL, Communication and Mass Media Complete, MEDLINE, PsycArticles, and PsycInfo were searched. A cited reference search of articles meeting the inclusion criteria was also conducted to reduce misses. Fifty-two articles met the selection criteria. Among them, 94 diff...

  1. Early Site Permit Demonstration Program: Regulatory criteria evaluation report

    Energy Technology Data Exchange (ETDEWEB)

    1993-03-01

    The primary objective of the ESPDP is to demonstrate successfully the use of 10CFR52 to obtain ESPs for one or more US sites for one (or more) ALWR nuclear power plants. It is anticipated that preparation of the ESP application and interaction with NRC during the application review process will result not only in an ESP for the applicant(s) but also in the development of criteria and definition of processes, setting the precedent that facilitates ESPs for subsequent ESP applications. Because siting regulatory processes and acceptance criteria are contained in over 100 separate documents, comprehensive licensing and technical reviews were performed to establish whether the requirements and documentation are self-consistent, whether the acceptance criteria are sufficiently well-defined and clear, and whether the licensing process leading to the issuance of an ESP is unambiguously specified. The results of the technical and licensing evaluations are presented in this report. The purpose, background, and organization of the ESPDP is delineated in Section 1. Section 11 contains flowcharts defining siting application requirements, environmental report requirements, and emergency planning/preparedness requirements for ALWRS. The licensing and technical review results are presented in Section III.

  2. Early Site Permit Demonstration Program: Regulatory criteria evaluation report

    International Nuclear Information System (INIS)

    1993-03-01

    The primary objective of the ESPDP is to demonstrate successfully the use of 10CFR52 to obtain ESPs for one or more US sites for one (or more) ALWR nuclear power plants. It is anticipated that preparation of the ESP application and interaction with NRC during the application review process will result not only in an ESP for the applicant(s) but also in the development of criteria and definition of processes, setting the precedent that facilitates ESPs for subsequent ESP applications. Because siting regulatory processes and acceptance criteria are contained in over 100 separate documents, comprehensive licensing and technical reviews were performed to establish whether the requirements and documentation are self-consistent, whether the acceptance criteria are sufficiently well-defined and clear, and whether the licensing process leading to the issuance of an ESP is unambiguously specified. The results of the technical and licensing evaluations are presented in this report. The purpose, background, and organization of the ESPDP is delineated in Section 1. Section 11 contains flowcharts defining siting application requirements, environmental report requirements, and emergency planning/preparedness requirements for ALWRS. The licensing and technical review results are presented in Section III

  3. Acceptance test report for the Westinghouse 100 ton hydraulic trailer

    International Nuclear Information System (INIS)

    Barrett, R.A.

    1995-01-01

    The SY-101 Equipment Removal System 100 Ton Hydraulic Trailer was designed and built by KAMP Systems, Inc. Performance of the Acceptance Test Procedure at KAMP's facility in Ontario, California (termed Phase 1 in this report) was interrupted by discrepancies noted with the main hydraulic cylinder. The main cylinder was removed and sent to REMCO for repair while the trailer was sent to Lampson's facility in Pasco, Washington. The Acceptance Test Procedure was modified and performance resumed at Lampson (termed Phase 2 in this report) after receipt of the repaired cylinder. At the successful conclusion of Phase 2 testing the trailer was accepted as meeting all the performance criteria specified

  4. The role of natural analogues in safety assessment and acceptability

    International Nuclear Information System (INIS)

    Papp, Toenis

    1987-01-01

    The safety assessment must evaluate the level of safety for a repository, the confidence that can be placed on the assessment and how well the repository can meet the acceptance criteria of the society. Many of the processes and phenomena that govern the long term performance of a deep geologic repository for radioactive waste also take place in nature. To investigate these natural analogues and try to validate the models on which the safety assessment are based is a main task in the effort to build of confidence in the safety assessments. The assessment of the safety of a repository can, however, not only be based on good models. The possible role of natural analogues or natural evidence in other parts of the safety assessment is discussed. Specially with regard to - the need to demonstrate that all relevant processes have been taken into account, and that the important ones have been validated to an acceptable level for relevant parameters spans, -the definition and analysis of external scenarios for the safety assessment and for the claim that all reasonable scenarios have been addressed, - the public confidence in the long-term relevance of the acceptance criteria. (author)

  5. Seismic design criteria for the system 80+ advanced light water reactor

    International Nuclear Information System (INIS)

    Manrique, M.A.; Dermitzakis, S.N.; Gerdes, L.D.; Kennedy, R.P.; Idriss, I.M.; Cassidy, J.R.

    1991-01-01

    This paper presents the development of seismic design criteria in support of design certification by the Nuclear Regulatory Commission (NRC) of the ABB-Combustion Engineering's System 80+ Standard Design. The design certification effort is sponsored by the US Department of Energy (DOE). The development of the design criteria included: (a) development of the seismic control motion, (b) development of generic soil profiles for anticipated sites, (c) generation of in-structure response spectra and design loads for structures and equipment through soil-structure interaction (SSI) analyses, and (d) acceptance criteria for future construction sites

  6. Feasibility and acceptability of electronic symptom surveillance with clinician feedback using the Patient-Reported Outcomes version of Common Terminology Criteria for Adverse Events (PRO-CTCAE) in Danish prostate cancer patients

    DEFF Research Database (Denmark)

    Bæksted, Christina; Pappot, Helle; Nissen, Aase

    2017-01-01

    -CTCAE questionnaire on tablet computers using AmbuFlex software at each treatment visit in the outpatient clinic. In total, 22 symptomatic toxicities (41 PRO-CTCAE items), corresponding to the symptomatic adverse-events profile associated with the regimens commonly used for prostate cancer treatment (Docetaxel......Background: The aim was to examine the feasibility, acceptability and clinical utility of electronic symptom surveillance with clinician feedback using a subset of items drawn from the Patient-Reported Outcomes version of Common Terminology Criteria for Adverse Events (PRO-CTCAE) in a cancer...

  7. Variability amongst radiographers in the categorization of clinical acceptability for digital trauma radiography

    Science.gov (United States)

    Decoster, Robin; Toomey, Rachel; Smits, Dirk; Mol, Harrie; Verhelle, Filip; Butler, Marie-Louise

    2016-03-01

    Introduction: Radiographers evaluate anatomical structures to judge clinical acceptability of a radiograph. Whether a radiograph is deemed acceptable for diagnosis or not depends on the individual decision of the radiographer. Individual decisions cause variation in the accepted image quality. To minimise these variations definitions of acceptability, such as in RadLex, were developed. On which criteria radiographers attribute a RadLex categories to radiographs is unknown. Insight into these criteria helps to further optimise definitions and reduce variability in acceptance between radiographers. Therefore, this work aims the evaluation of the correlation between the RadLex classification and the evaluation of anatomical structures, using a Visual Grading Analysis (VGA) Methods: Four radiographers evaluated the visibility of five anatomical structures of 25 lateral cervical spine radiographs on a secondary class display with a VGA. They judged clinical acceptability of each radiograph using RadLex. Relations between VGAS and RadLex category were analysed with Kendall's Tau correlation and Nagelkerke pseudo-R². Results: The overall VGA score (VGAS) and the RadLex score correlate (rτ= 0.62, pscore. The reproduction of spinous processes (rτ=0.67, pscore. Conclusion: RadLex scores and VGAS correlate positively, strongly and significantly. The predictive value of bony structures may support the use of these in the judgement of clinical acceptability. Considerable inter-observer variations in the VGAS within a certain RadLex category, suggest that observers use of observer specific cut-off values.

  8. Acceptance criteria for reprocessed AcuNav catheters: comparison between functionality testing and clinical image assessment.

    Science.gov (United States)

    Bank, Alan J; Berry, James M; Wilson, Robert F; Lester, Bruce R

    2009-03-01

    The AcuNav-catheter is a vector-phased array ultrasound catheter that has shown great utility for both diagnosis and electrophysiological interventions. To test the feasibility of limited catheter reuse and to ensure that reprocessed catheters would produce acceptable clinical images, the present study compared the 2-D and Doppler image quality, as determined by clinical assessment, with the catheter's functional status as determined by the FirstCall 2000 transducer tester. Reprocessed catheters from four functional categories, two acceptable and two unacceptable, were used to collect images, 2-D and Doppler, from a porcine heart. The images were blinded and then rated by clinical evaluation. The study found that catheter images from all functional categories were found to be clinically acceptable except for those from the lowest unacceptable category. In addition, examination of tip deflection characteristics showed no significant difference between new and reprocessed catheters. We conclude that reprocessed AcuNav catheters that pass functional tests are able to produce clinical images, 2-D and Doppler, which are equivalent to their new counterparts.

  9. Dysplastic naevus: histological criteria and their inter-observer reproducibility.

    Science.gov (United States)

    Hastrup, N; Clemmensen, O J; Spaun, E; Søndergaard, K

    1994-06-01

    Forty melanocytic lesions were examined in a pilot study, which was followed by a final series of 100 consecutive melanocytic lesions, in order to evaluate the inter-observer reproducibility of the histological criteria proposed for the dysplastic naevus. The specimens were examined in a blind fashion by four observers. Analysis by kappa statistics showed poor reproducibility of nuclear features, while reproducibility of architectural features was acceptable, improving in the final series. Consequently, we cannot apply the combined criteria of cytological and architectural features with any confidence in the diagnosis of dysplastic naevus, and, until further studies have documented that architectural criteria alone will suffice in the diagnosis of dysplastic naevus, we, as pathologists, shall avoid this term.

  10. Spent nuclear fuel project-criteria document Cold Vacuum Drying Facility phase 2 safety analysis report

    International Nuclear Information System (INIS)

    Garvin, L.J.

    1998-01-01

    The criteria document provides the criteria and guidance for developing the SNF CVDF Phase 2 SAR. This SAR will support the US Department of Energy, Richland Operations Office decision to authorize the procurement, installation, and installation acceptance testing of the CVDF systems

  11. Acceptance test report, plutonium finishing plant life safety upgrade

    International Nuclear Information System (INIS)

    Hodge, S.G.

    1994-01-01

    This acceptance Test Procedure (ATP) has been prepared to demonstrate that modifications to the Fir Protection systems function as required by project criteria. The ATP will test the Fire Alarm Control Panels, Flow Alarm Pressure Switch, Heat Detectors, Smoke Detectors, Flow Switches, Manual Pull Stations, and Gong/Door By Pass Switches

  12. Selection of an Appropriate Mechanized Mining Technical Process for Thin Coal Seam Mining

    Directory of Open Access Journals (Sweden)

    Chen Wang

    2015-01-01

    Full Text Available Mechanized mining technical process (MMTP related to the control method of the shearer is a vital process in thin coal seam mining operations. An appropriate MMTP is closely related to safety, productivity, labour intensity, and efficiency. Hence, the evaluation of alternative MMTP is an important part of the mining design. Several parameters should be considered in MMTP evaluation, so the evaluation is complex and must be compliant with a set of criteria. In this paper, two multiple criteria decision-making (MCDM methods, Analytic Hierarchy Process (AHP and Preference Ranking Organization Method for Enrichment Evaluation (PROMETHEE, were adopted for this evaluation. Then, the most appropriate MMTP for a thin coal seam working face was selected in China.

  13. Acceptance test report for the Westinghouse 100 ton hydraulic trailer

    Energy Technology Data Exchange (ETDEWEB)

    Barrett, R.A.

    1995-03-06

    The SY-101 Equipment Removal System 100 Ton Hydraulic Trailer was designed and built by KAMP Systems, Inc. Performance of the Acceptance Test Procedure at KAMP`s facility in Ontario, California (termed Phase 1 in this report) was interrupted by discrepancies noted with the main hydraulic cylinder. The main cylinder was removed and sent to REMCO for repair while the trailer was sent to Lampson`s facility in Pasco, Washington. The Acceptance Test Procedure was modified and performance resumed at Lampson (termed Phase 2 in this report) after receipt of the repaired cylinder. At the successful conclusion of Phase 2 testing the trailer was accepted as meeting all the performance criteria specified.

  14. Development of flaw evaluation and acceptance procedures for flaw indications in the cooling water system at the Savannah River site K reactor

    International Nuclear Information System (INIS)

    Tandon, S.; Bamford, W.H.; Cowfer, C.D.; Ostrowski, R.

    1993-01-01

    This paper describes the methodology used in determining the criteria for acceptance of inspection indications in the K-Reactor Cooling Water System at the Savannah River Plant. These criteria have been developed in a manner consistent with the development of similar criteria in the ASME Code Section XI for commercial light water reactors, but with a realistic treatment of the operating conditions in the cooling water system. The technical basis for the development of these criteria called ''Acceptance Standards'' is contained in this paper. A second portion of this paper contains the methodology used in the construction of flaw evaluation charts which have been developed for each specific line size in the cooling water system. The charts provide the results of detailed fracture mechanics calculations which have been completed to determine the largest flaw which can be accepted in the cooling water system without repair. These charts are designed for use in conjunction with in-service inspections of the cooling water system, and only require inspection results to determine acceptability

  15. New contact boiling experiments to evaluate Calandria tube strain acceptance criteria

    Energy Technology Data Exchange (ETDEWEB)

    El-Hawary, M.; Szymanski, J.; Tanase, A.; Delja, A.; Oussoren, A., E-mail: Magdy.El-Hawary@cnsc-ccsn.gc.ca [Canadian Nuclear Safety Comission, Ottawa, ON (Canada); Neal, P. [Canadian Nuclear Laboratories, Chalk River, ON (Canada)

    2015-07-01

    The Canadian Nuclear Safety Commission(CNSC) has contracted the Canadian Nuclear Laboratories(CNL) to conduct additional Contact Boiling (CB) experiments with the main objective of evaluating the acceptance criterion of CalandriaTube (CT) strain limit of 2%, proposed by the industry for fuel channel integrity assessments. The test conditions are selected using analytical tools and guidance from existing CANDU Owners Group (COG) test results, so as to lead to CT strain close to this value. The experiments will also be used to evaluate the CT quench temperature correlation proposed. This paper presents conditions selected for the first three experiments, their most important results and their preliminary analysis, with a focus on the test which produced CT strain in excess of 2%. (author)

  16. Upgraded acceptance criteria from transient thermography control for the W7-X divertor target elements

    Energy Technology Data Exchange (ETDEWEB)

    Missirlian, M. [CEA, IRFM, F-13108 Saint-Paul-Lez-Durance (France)], E-mail: marc.missirlian@cea.fr; Boscary, J. [Max-Planck-Institut fuer Plasmaphysik, Euratom Association, Boltzmannstr. 2, D-85748 Garching (Germany); Guigon, R.; Schlosser, J.; Durocher, A. [CEA, IRFM, F-13108 Saint-Paul-Lez-Durance (France); Greuner, H. [Max-Planck-Institut fuer Plasmaphysik, Euratom Association, Boltzmannstr. 2, D-85748 Garching (Germany)

    2009-06-15

    The commissioning of plasma-facing component fields needs advanced non-destructive methods to detect in a reliable way the defects, which can impair the component performances and/or integrity during operation. Within this framework, CEA developed a dedicated non-destructive examination method based on active infrared thermography (SATIR facility) to inspect the bonding between armour material and metallic heat sink. Used with successful in the commissioning of the toroidal pump limiter of Tore Supra, this technique was applied in the frame of the pre-series activities of the Wendelstein 7-X high heat flux divertor elements to assess the bonding quality of the delivered components. This paper presents the methodology adopted to define an acceptance criterion based on SATIR test bed possibly applied for a serial inspection of the Wendelstein 7-X elements. Using the well-tried acceptance test based on the DTref{sub m}ax parameter, the new method includes advanced data post-processing techniques from thermo-signal SATIR and a data merging method to help the decision-making and to optimise the reliability of the binary response expected for a final decision in terms of acceptance test.

  17. Upgraded acceptance criteria from transient thermography control for the W7-X divertor target elements

    International Nuclear Information System (INIS)

    Missirlian, M.; Boscary, J.; Guigon, R.; Schlosser, J.; Durocher, A.; Greuner, H.

    2009-01-01

    The commissioning of plasma-facing component fields needs advanced non-destructive methods to detect in a reliable way the defects, which can impair the component performances and/or integrity during operation. Within this framework, CEA developed a dedicated non-destructive examination method based on active infrared thermography (SATIR facility) to inspect the bonding between armour material and metallic heat sink. Used with successful in the commissioning of the toroidal pump limiter of Tore Supra, this technique was applied in the frame of the pre-series activities of the Wendelstein 7-X high heat flux divertor elements to assess the bonding quality of the delivered components. This paper presents the methodology adopted to define an acceptance criterion based on SATIR test bed possibly applied for a serial inspection of the Wendelstein 7-X elements. Using the well-tried acceptance test based on the DTref m ax parameter, the new method includes advanced data post-processing techniques from thermo-signal SATIR and a data merging method to help the decision-making and to optimise the reliability of the binary response expected for a final decision in terms of acceptance test.

  18. Analysis of a Thin Optical Lens Model

    Science.gov (United States)

    Ivchenko, Vladimir V.

    2011-01-01

    In this article a thin optical lens model is considered. It is shown that the limits of its applicability are determined not only by the ratio between the thickness of the lens and the modules of the radii of curvature, but above all its geometric type. We have derived the analytical criteria for the applicability of the model for different types…

  19. Acceptance criteria for interim dry storage of aluminum-clad fuels

    International Nuclear Information System (INIS)

    Sindelar, R.L.; Peacock, H.B. Jr.; Iyer, N.C.; Louthan, M.R. Jr.

    1994-01-01

    Direct repository disposal of foreign and domestic research reactor fuels owned by the United States Department of Energy is an alternative to reprocessing (together with vitrification of the high level waste and storage in an engineered barrier) for ultimate disposition. Neither the storage systems nor the requirements and specifications for acceptable forms for direct repository disposal have been developed; therefore, an interim storage strategy is needed to safely store these fuels. Dry storage (within identified limits) of the fuels received from wet-basin storage would avoid excessive degradation to assure post-storage handleability, a full range of ultimate disposal options, criticality safety, and provide for maintaining confinement by the fuel/clad system. Dry storage requirements and technologies for US commercial fuels, specifically zircaloy-clad fuels under inert cover gas, are well established. Dry storage requirements and technologies for a system with a design life of 40 years for dry storage of aluminum-clad foreign and domestic research reactor fuels are being developed by various groups within programs sponsored by the DOE

  20. Design criteria for the structural analysis of shipping cask containment vessels

    International Nuclear Information System (INIS)

    Anon.

    1979-01-01

    10 CFR Part 71, Sections 71.35 and 71.36, require that packages used to transport radioactive materials meet specified normal and hypothetical accident conditions. Acceptable design criteria are presented for use in the structural analysis of the containment vessels of Type B packages used to transport irradiated nuclear fuel. Alternative design criteria meeting the structural requirements of 10 CFR Part 71, Section 71.35 and 71.36, may also be used

  1. Independent review of Oak Ridge HCTW test program and development of seismic evaluation criteria

    International Nuclear Information System (INIS)

    1995-05-01

    Many of the existing buildings at the Oak Ridge Y-12 Plant are steel frame construction with unreinforced hollow clay tile infill walls (HCTW). The HCTW infill provides some lateral seismic resistance to the design/evaluation basis earthquake; however acceptance criteria for this construction must be developed. The basis for the development of seismic criteria is the Oak Ridge HCTW testing and analysis program and the target performance goals of DOE 5480.28 and DOE-STD-1020-94. This report documents and independent review of the testing and analysis program and development of recommended acceptance criteria for Oak Ridge HCTW construction. The HCTW test program included ''macro'' wall in-plane and out-of-plane tests, full-scale wall in-plane and out-of-plane tests, in-situ out-of-plane test, shake table tests, and masonry component tests

  2. Acceptance criteria for the evaluation of Category 1 fuel cycle facility physical security plans

    Energy Technology Data Exchange (ETDEWEB)

    Dwyer, P.A.

    1991-10-01

    This NUREG document presents criteria developed from US Nuclear Regulatory Commission regulations for the evaluation of physical security plans submitted by Category 1 fuel facility licensees. Category 1 refers to those licensees who use or possess a formula quantity of strategic special nuclear material.

  3. Acceptance criteria for the evaluation of Category 1 fuel cycle facility physical security plans

    International Nuclear Information System (INIS)

    Dwyer, P.A.

    1991-10-01

    This NUREG document presents criteria developed from US Nuclear Regulatory Commission regulations for the evaluation of physical security plans submitted by Category 1 fuel facility licensees. Category 1 refers to those licensees who use or possess a formula quantity of strategic special nuclear material

  4. Analysis of existing work-zone devices with MASH safety performance criteria.

    Science.gov (United States)

    2009-02-01

    Crashworthy, work-zone, portable sign support systems accepted under NCHRP Report No. 350 were analyzed to : predict their safety peformance according to the TL-3 MASH evaluation criteria. An analysis was conducted to determine : which hardware param...

  5. International comparison of safety criteria applied to radwaste repositories. Safety aspects of the post-operational phase

    International Nuclear Information System (INIS)

    Baltes, B.

    1994-01-01

    There is a generally accepted system of framework safety conditions governing the construction, operation, and post-operational monitoring of radwaste repositories. Although the development of these framework conditions may vary from country to country, the resulting criteria are based on the commonly accepted system of priciples and purposes established for ultimate radioactive waste disposal. The experience accumulated by GRS in the course of the plan approval procedure for the Konrad mine site and the safety-relevant studies performed for the planned Morsleben repository clearly show demand for further development of the safety criteria. In Germany, it is especially the safety criteria and detailed requirements filling the framework safety conditions that need revision and in-depth definition, as well as comparison and harmonisation with internationally applied criteria. These activities will particularly consider the international convention on radioactive waste management currently in preparation under the auspieces of the IAEA. (orig.) [de

  6. Development of small reactor safety criteria in Canada

    International Nuclear Information System (INIS)

    Ernst, P.C.; French, P.M.; Axford, D.J.; Snell, V.G.

    1990-01-01

    A number of new small reactor designs have been proposed in Canada over the last several years and some have reached the stage where licensing discussions have been initiated with the Atomic Energy Control Board (AECB). An inter-organizational Small Reactor Criteria (SRC) working group was formed in 1988 to propose safety and licensing criteria for these small reactors. Two levels of criteria are proposed. The first level forms a safety philosophy and the second is a set of criteria for specific reactor applications. The safety philosophy consists of three basic safety objectives together with evaluation criteria, and fourteen fundamental principles measured by specific criteria, which must be implemented to meet the safety objectives. Two of the fourteen principles are prime: defence in depth, and safety culture; the other twelve principles can be seen as deriving from them. A benefit of this approach is that the concepts of defence in depth and safety culture become well-defined. The objectives and principles are presented in the paper and their criteria are summarized. The second level of criteria, under development, will form a safety application set and will provide small reactor criteria in a number of general areas, such as regulatory process and safety assessment, as well as for specific reactor life-cycle activities, from siting through to decommissioning. The criteria are largely deterministic. However, the frequencies and consequences of postulated accidents are assessed against numerical criteria to assist in judging the acceptability of plant design, operation, and proposed siting. All criteria proposed are designed to be testable in some evidentiary fashion, readily enabling an assessment of compliance for a given proposal

  7. Criteria for candidate species for aquaculture

    Energy Technology Data Exchange (ETDEWEB)

    Webber, H H; Riordan, P F

    1976-01-01

    The nature of the animal taxa that are the most probable candidates for an intensive, commercial aquatic animal husbandry industry is considered. A characterization is presented of those biological criteria that lend the species the necessary physiological and genetic malleability to be adapted and molded into a domesticated race. The animal cultivated must be amenable to intensive management in high-density confinements such as those now being engineered for high-yield aquaculture. Attributes considered are discussed in the context of the various aquacultural ecosystems in which the specific biotype is expected to achieve satisfactory growth and survival. Correlative with bionomic criteria, economic requirements are posed and evaluated in an effort to define a socially and financially profitable agribusiness system. Investment requirements and operating costs are considered in terms of expected returns. However, since production alone is insufficient to sustain an enterprise - i.e., the product must be sold - production costs must be judged against market values. Therefore, ultimate use or consumer acceptance criteria are incorporated into the list of essential requirements for a candidate species for aquafarming.

  8. Which trees should be removed in thinning?

    Directory of Open Access Journals (Sweden)

    Timo Pukkala

    2015-12-01

    Full Text Available Background: In economically optimal management, trees that are removed in a thinning treatment should be selected on the basis of their value, relative value increment and the effect of removal on the growth of remaining trees. Large valuable trees with decreased value increment should be removed, especially when they overtop smaller trees. Methods: This study optimized the tree selection rule in the thinning treatments of continuous cover management when the aim is to maximize the profitability of forest management. The weights of three criteria (stem value, relative value increment and effect of removal on the competition of remaining trees were optimized together with thinning intervals. Results and conclusions: The results confirmed the hypothesis that optimal thinning involves removing predominantly large trees. Increasing stumpage value, decreasing relative value increment, and increasing competitive influence increased the likelihood that removal is optimal decision. However, if the spatial distribution of trees is irregular, it is optimal to leave large trees in sparse places and remove somewhat smaller trees from dense places. However, the benefit of optimal thinning, as compared to diameter limit cutting is not usually large in pure one-species stands. On the contrary, removing the smallest trees from the stand may lead to significant (30–40 % reductions in the net present value of harvest incomes. Keywords: Continuous cover forestry, Tree selection, High thinning, Optimal management, Spatial distribution, Spatial growth model

  9. Multiaxial loading of large-diameter, thin-walled tube rock specimens

    International Nuclear Information System (INIS)

    Hecker, S.S.; Petrovic, J.J.

    1981-01-01

    A large-scale mechanical testing facility permits previously impossible thin-walled tube multiaxial loading experiments on rock materials. Constraints are removed regarding tube wall thickness in relation to rock microstructural features and tube diameter as well as test machine load capacity. Thin-walled tube studies clarify the influence of intermediate principal stress sigma 2 on rock fracture and help define a realistic rock fracture criterion for all multiaxial stressing situations. By comparing results of thin-walled and thick-walled tube fracture investigations, effects of stress gradients can be established. Finally, influence of stress path on rock fracture, an area largely ignored in current rock failure criteria, can be examined in detail using controlled loading changes as well as specimen prestrains

  10. Criteria for cesium capsules to be shipped as special form radioactive material

    International Nuclear Information System (INIS)

    Lundeen, J.E.

    1994-01-01

    The purpose of this report is to compile all the documentation which defines the criteria for Waste Encapsulation and Storage Facility (WESF) cesium capsules at the IOTECH facility and Applied Radiant Energy Corporation (ARECO) to be shipped as special form radioactive material in the Beneficial Uses Shipping System (BUSS) Cask. The capsules were originally approved as special form in 1975, but in 1988 the integrity of the capsules came into question. WHC developed the Pre-shipment Acceptance Test Criteria for capsules to meet in order to be shipped as special form material. The Department of Energy approved the criteria and directed WHC to ship the capsules at IOTECH and ARECO meeting this criteria to WHC as special form material

  11. The acceptability of the female and male condom: a randomized crossover trial.

    Science.gov (United States)

    Kulczycki, Andrzej; Kim, Dhong-Jin; Duerr, Ann; Jamieson, Denise J; Macaluso, Maurizio

    2004-01-01

    Although studies have assessed the acceptability of male and female condoms, comparative trial data are lacking. A sample of 108 women in stable relationships recruited from an urban, reproductive health clinic were randomly assigned to use 10 male or female condoms, followed by use of 10 of the other type. A nurse provided instruction in correct method use. Demographic information was collected in a baseline questionnaire; acceptability data were collected in follow-up and exit questionnaires and coital logs. Nonparametric and chi-square statistics were used to analyze measures of the methods' relative acceptability. Bowker's test of symmetry was adapted to test the null hypothesis of no difference in acceptability between condom types. Participants used 678 female and 700 male condoms. Although neither method scored high on user satisfaction measures, the 63 women completing the study protocol preferred the male condom to the female condom for ease of application or insertion, ease of removal, general fit, feel of the condom during intercourse and ease of penetration. Participants reported that their partner also favored the male condom, although women generally appeared to like this method more than their partner did. In a direct comparison between the methods at the end of the study, women generally judged male condoms superior on specified preference criteria. Across a range of criteria, the female condom was less acceptable than the male condom to most women and their partners. Although both types had low acceptability, they are needed and valid methods of pregnancy and disease prevention. That neither rated high on user satisfaction measures underscores the need for more barrier methods that women and men can use.

  12. Reportable Nuclide Criteria for ORNL Radioactive Waste Management Activities - 13005

    International Nuclear Information System (INIS)

    McDowell, Kip; Forrester, Tim; Saunders, Mark

    2013-01-01

    The U.S. Department of Energy's Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee generates numerous radioactive waste streams. Many of those streams contain a large number of radionuclides with an extremely broad range of concentrations. To feasibly manage the radionuclide information, ORNL developed reportable nuclide criteria to distinguish between those nuclides in a waste stream that require waste tracking versus those nuclides of such minimal activity that do not require tracking. The criteria include tracking thresholds drawn from ORNL onsite management requirements, transportation requirements, and relevant treatment and disposal facility acceptance criteria. As a management practice, ORNL maintains waste tracking on a nuclide in a specific waste stream if it exceeds any of the reportable nuclide criteria. Nuclides in a specific waste stream that screen out as non-reportable under all these criteria may be dropped from ORNL waste tracking. The benefit of these criteria is to ensure that nuclides in a waste stream with activities which meaningfully affect safety and compliance are tracked, while documenting the basis for removing certain isotopes from further consideration. (authors)

  13. General criteria for radioactive waste disposal

    International Nuclear Information System (INIS)

    Maxey, M.N.; Musgrave, B.C.; Watkins, G.B.

    1979-01-01

    Techniques are being developed for conversion of radioactive wastes to solids and their placement into repositories. Criteria for such disposal are needed to assure protection of the biosphere. The ALARA (as low as reasonably achievable) principle should be applicable at all times during the disposal period. Radioactive wastes can be categorized into three classes, depending on the activity. Three approaches were developed for judging the adequacy of disposal concepts: acceptable risk, ore body comparison, and three-stage ore body comparison

  14. Emotional and Spiritual Quotient Approach Improve Biology Education Students’ Acceptance of Evolution Theory

    Science.gov (United States)

    Darussyamsu, R.; Fadilah, M.; Putri, D. H.

    2018-04-01

    Emotional and spiritual aspect is one of main factors that influence students’ acceptance of a theory. This study aim to measure university students’ acceptance of evolution by learns evolution using emotional and spiritual quotient (ESQ) approach. This is a quasi-experimental research using one shot case study design with the subject 36 biology educational students at Biology Department, Faculty of Mathematics and Natural Science, Universitas Negeri Padang. Data collected using the MATE instrument by Rutledge and Warden (2000) after the students learn evolution for eight meetings since January until March 2017. The result showed that by learning evolution theory combine with ESQ aspects increase students acceptance from very low become moderate acceptance. It concluded that ESQ aspects can improve students’ acceptance of evolution. Any criteria depend on it are discussed.

  15. The use of fracture mechanics for the evaluation of NDE flaw acceptance standards

    Energy Technology Data Exchange (ETDEWEB)

    Alicino, A; Capurro, E; Ansaldo, Sp; Corvi, A [Ansaldo SpA, Genoa (Italy)

    1988-12-31

    This document deals with the use of fracture mechanics criteria to evaluate the Non Destructive Examination (NDE) flaw acceptance standards. The communication discusses the general schemes and the guidelines of the activity carried out. (TEC).

  16. Thermodynamical fluctuations and critical behavior in weakly disordered YBCO thin and ultra-thin films

    International Nuclear Information System (INIS)

    Lesueur, J.; Aprili, M.; Degoy, S.; Chambonnet, D.; Keller, D.

    1996-01-01

    The specific role of disorder in the transport properties of YBCO has been investigated, using both light-ion irradiation of thin films to finely tune the amount of atomic disorder, and ultra-thin films grown to study possible dimensional effects. For weak disorder, the samples display a resistive transition typical of the mean-field paraconductive regime of a homogeneous media, well described by the Lawrence and Doniach model for layered superconductors. As the disorder increases, two effects take place. First, the c-axis coherence length becomes shorter, leading to a more anisotropic material, as shown by the excess conductivity above T c . Second, an incipient granularity is revealed, leading to a less sharper transition, which is analyzed within the random 3D XY critical model for the paracoherence transition. Two main results are derived: an experimental test of the Ginzburg criteria for the paracoherence transition, and a new fluctuation regime in nanometric grain size superconductors

  17. AAPT Diagnostic Criteria for Chronic Cancer Pain Conditions

    OpenAIRE

    Paice, Judith A.; Mulvey, Matt; Bennett, Michael; Dougherty, Patrick M.; Farrar, John T.; Mantyh, Patrick W.; Miaskowski, Christine; Schmidt, Brian; Smith, Thomas J.

    2016-01-01

    Chronic cancer pain is a serious complication of malignancy or its treatment. Currently, no comprehensive, universally accepted cancer pain classification system exists. Clarity in classification of common cancer pain syndromes would improve clinical assessment and management. Moreover, an evidence-based taxonomy would enhance cancer pain research efforts by providing consistent diagnostic criteria, ensuring comparability across clinical trials. As part of a collaborative effort between the A...

  18. Thermo-mechanical failure criteria for x-ray windows and filters and comparison with experiments

    International Nuclear Information System (INIS)

    Wang, Z.; Kuzay, T.M.

    1993-01-01

    Synchrotron x-ray windows are vacuum separators and are usually made of thin beryllium metal. Filters are provided upstream of the window to filter out the soft x-rays to protect the window from overheating and failing. The filters are made of thin carbon products or sometimes beryllium, the same material as the window. Because the window is a vacuum separator, understanding its potential structural failure under thermal load is very important. Current structural failure models for the brazed windows and filters under thermal stresses are not very accurate. Existing models have been carefully examined and found to be inconsistent with the actual failure modes of windows tested. Due to the thinness of the filter/window, the most likely failure mode is thermal buckling. In fact, recent synchrotron tests conducted in Japan on window failures bear out this position. In this paper, failure criteria for filters/windows are proposed, and analyses are performed and compared with the experimental results from various sources. A consistent result is found between the analysis and reported experiments. A series of additional analyses based on the proposed failure criteria is also carried out for filter and window designs for the third generation synchrotron beamline front ends. Comparative results are presented here

  19. Bayesian predictive risk modeling of microbial criteria for Campylobacter in broilers

    DEFF Research Database (Denmark)

    Nauta, Maarten; Ranta, J.; Mikkelä, A.

    Microbial Criteria define the acceptability of food products, based on the presence or detected number of microorganisms in samples. The criteria are applied at the level of defined food lots. Generally, these are interpreted as statistical batches representing the production [1]. The batches...... be assessed by computing posterior distribution of the parameters - a Bayesian evidence synthesis. The outcome of a defined Microbial Criterion (MC) for a batch provides additional evidence concerning the batch. Posterior predictive consumer risk (probability of illness) was computed for such batch...

  20. Artificial intelligence aiding the thin-section CT diagnosis of diffuse pulmonary diseases

    International Nuclear Information System (INIS)

    Han, Dae Hee; Koh, Young Hwan; Seong, Chang Kyu; Kim, Ji Hoon; Choi, Young Ho; Kim, Jong Hyo; Chae, Young Moon; Lee, Yun Hee; Han, Heon

    2006-01-01

    We wanted to develop and test an artificial intelligence (AI) to assist physicians in making the thin-section CT diagnosis of diffuse pulmonary diseases. The AI was composed of knowledge bases (KB) of 12 diffuse pulmonary diseases and an inference engine (IE). The KB of a disease included both the inclusion criteria (IC) and the exclusion criteria (EC), which were the clinical or thin-section CT findings that were known to be present or absent in that particular disease, respectively. From imputing the clinical or thin-section CT findings by the operator who was reading the thin-section CT, AI instantly executed the following two steps. First, the IE eliminated all diseases from the list which the EC had for those particular findings. Next, from a list or remaining diseases, the AI selected those diseases having those findings in its IC to formulate the 1st-step differential diagnosis (DD1). For the differential diagnosis in the next step, the reader could choose one more clinical or thin-section CT finding from the new list: [(all the findings in the IC or EC of DD1)-(the findings in the IC common to all the DD1s)]. The reader could proceed even further if needed. The system was tested on 10 radiology residents who solved 24 problems (two problems for each of 12 diffuse pulmonary diseases) without and then with the aid of the AI. The scores were compared using the Wilcoxon signed rank test. An AI was made; it was composed of 280 rules (214 IC and 66 EC) and there interfaces (two for program management and another for problem solving). Contestants scored higher (ρ = 0.0078) using the AI (167 vs. 110 respectively), and they responded that they felt that the program was helpful in making decisions. AI appeared to be helpful in making thin-section CT diagnosis

  1. Artificial intelligence aiding the thin-section CT diagnosis of diffuse pulmonary diseases

    Energy Technology Data Exchange (ETDEWEB)

    Han, Dae Hee; Koh, Young Hwan; Seong, Chang Kyu; Kim, Ji Hoon; Choi, Young Ho [Boramae Munincipal Hospital, Seoul National University College of Medicine, Seoul (Korea, Republic of); Kim, Jong Hyo [Seoul National University College of Medicine, Seoul (Korea, Republic of); Chae, Young Moon [Yonsei University Graduate School of Public Heath, Seoul (Korea, Republic of); Lee, Yun Hee [The Graduate School of Imformation, Yonsei, Seoul (Korea, Republic of); Han, Heon [Kangwon National University College of Medicine, Chuncheon (Korea, Republic of)

    2006-06-15

    We wanted to develop and test an artificial intelligence (AI) to assist physicians in making the thin-section CT diagnosis of diffuse pulmonary diseases. The AI was composed of knowledge bases (KB) of 12 diffuse pulmonary diseases and an inference engine (IE). The KB of a disease included both the inclusion criteria (IC) and the exclusion criteria (EC), which were the clinical or thin-section CT findings that were known to be present or absent in that particular disease, respectively. From imputing the clinical or thin-section CT findings by the operator who was reading the thin-section CT, AI instantly executed the following two steps. First, the IE eliminated all diseases from the list which the EC had for those particular findings. Next, from a list or remaining diseases, the AI selected those diseases having those findings in its IC to formulate the 1st-step differential diagnosis (DD1). For the differential diagnosis in the next step, the reader could choose one more clinical or thin-section CT finding from the new list: [(all the findings in the IC or EC of DD1)-(the findings in the IC common to all the DD1s)]. The reader could proceed even further if needed. The system was tested on 10 radiology residents who solved 24 problems (two problems for each of 12 diffuse pulmonary diseases) without and then with the aid of the AI. The scores were compared using the Wilcoxon signed rank test. An AI was made; it was composed of 280 rules (214 IC and 66 EC) and there interfaces (two for program management and another for problem solving). Contestants scored higher ({rho} = 0.0078) using the AI (167 vs. 110 respectively), and they responded that they felt that the program was helpful in making decisions. AI appeared to be helpful in making thin-section CT diagnosis.

  2. Quality criteria for landscape visualisation

    International Nuclear Information System (INIS)

    Waldi, H.-P.; Witt, U. de

    1996-01-01

    The rapid expansion of wind energy utilisation in Western Europe can strain the limits of social acceptance with citizens living in wind development areas. One of the problems wind farm engineers and local authorities face is the visual impact of wind turbines. To determine the influence on the landscape visualisations of wind farms photorealistic compositions are used. In many cases it is part of the planning procedure. The quality of this visualization can strongly influence the success of the permission procedure. We will give criteria which can give help to reduce the possibility of unwanted manipulations. (author)

  3. Frequency limitations on reactor release derived from radiological criteria

    International Nuclear Information System (INIS)

    Clarke, R.H.

    1976-05-01

    Acceptable frequencies are suggested with which a number of defined individual and collective dose criteria are met. This has enabled a relationship to be proposed between the frequency and any event leading to release of radioactive material and the dose commitment to the hypothetical individual at the site boundary. The philosphy developed is generally applicable, but in this instance it has been demonstrated for an SGHW Reactor located at Sizewell. The results are derived on the basis of an acceptable level of risk of fatality to the most exposed individual and the application of the methodology to other reactor types and sites is demonstrated. (author)

  4. Draft principles, policy, and acceptance criteria for decommissioning of U.S. Department of Energy contaminated surplus facilities and summary of international decommissioning programs

    International Nuclear Information System (INIS)

    Singh, B.K.

    1994-12-01

    Decommissioning activities enable the DOE to reuse all or part of a facility for future activities and reduce hazards to the general public and any future work force. The DOE Office of Environment, Health and Safety has prepared this document, which consists of decommissioning principles and acceptance criteria, in an attempt to establish a policy that is in agreement with the NRC policy. The purpose of this document is to assist individuals involved with decommissioning activities in determining their specific responsibilities as identified in Draft DOE Order 5820.DDD, ''Decommissioning of US Department of Energy Contaminated Surplus Facilities'' (Appendix A). This document is not intended to provide specific decommissioning methodology. The policies and principles of several international decommissioning programs are also summarized. These programs are from the IAEA, the NRC, and several foreign countries expecting to decommission nuclear facilities. They are included here to demonstrate the different policies that are to be followed throughout the world and to allow the reader to become familiar with the state of the art for environment, safety, and health (ES and H) aspects of nuclear decommissioning

  5. Risk analysis and risk acceptance criteria in the planning processes of hazardous facilities-A case of an LNG plant in an urban area

    International Nuclear Information System (INIS)

    Vinnem, Jan Erik

    2010-01-01

    Planning of hazardous facilities is usually carried out on the basis of a risk-informed decision-making and planning process making use of risk analysis. This practice is well established in Norway under petroleum legislation but less so for onshore facilities under non-petroleum legislation. The present paper focuses on the use of risk analysis studies for risk evaluation against risk acceptance criteria, risk communication and derivation of technical and operational requirements in these circumstances. This is demonstrated through reference to a case study involving an LNG plant currently under construction in an urban area in Norway. The main finding is that risk-informed legislation is a fragile legislative system which is dependent on conscientious and open-minded use by the industrial developer. In the opposite case, the authorities may well be unable to correct the situation and the legislation may fail to protect the neighbourhood from unreasonable exposure to risk. Reference is also made to the international perspective where authorities define what is deemed tolerable risk, which would appear to be a more robust and defensible approach.

  6. Screening Criteria and Considerations of Offshore Enhanced Oil Recovery

    Directory of Open Access Journals (Sweden)

    Pan-Sang Kang

    2016-01-01

    Full Text Available The application of enhanced oil recovery (EOR in offshore oil fields has received significant attention due to the potentially enormous amount of recoverable oil. However, EOR application offshore is in its very early stage due to conditions that are more complex than onshore oil fields, owing to the unique parameters present offshore. Therefore, successful EOR applications in offshore oil fields require different screening criteria than those for conventional onshore applications. A comprehensive database for onshore applications of EOR processes together with a limited offshore EOR application database are analyzed in this paper, and the important parameters for successful offshore application are incorporated into the new EOR screening criteria. In this paper, screening criteria to determine acceptable EOR processes for offshore fields, including hydrocarbon gas miscible, CO2 miscible, and polymer processes, are presented. Suggested screening criteria for these EOR processes comprise quantitative boundaries and qualitative considerations. Quantitative screening criteria are predominantly based on quantifiable data, such as oil and reservoir properties. Qualitative screening considerations mainly focus on the operational issues present offshore, including platform space constraints, limited disposal options, injectant availability, and flow assurance matters (including hydrate formation and difficulties in emulsion separation.

  7. Criteria impacting shipments of Rocky Flats Plant radioactive mixed wastes

    International Nuclear Information System (INIS)

    Clawson, R.L.; Eide, J.H.

    1992-05-01

    Westinghouse Hanford Company, Transportation and Packaging Division, under contract for the Los Alamos Technology Office-Rocky Flats Plant, has developed this synopsis report to be used as a reference in the development of the Rocky Flats Plant Comprehensive Treatment and Management Plan and the Rocky Flats Plant Residue Elimination Plan. This report represents the criteria for packaging, shipping, and transporting Rocky Flats Plant radioactive mixed wastes. It is a compilation of state and federal regulations, US Department of Energy orders, and acceptance criteria specific to US Department of Energy radioactive mixed waste treatment, storage and disposal facilities

  8. Seismic design and evaluation criteria based on target performance goals

    International Nuclear Information System (INIS)

    Murray, R.C.; Nelson, T.A.; Kennedy, R.P.; Short, S.A.

    1994-04-01

    The Department of Energy utilizes deterministic seismic design/evaluation criteria developed to achieve probabilistic performance goals. These seismic design and evaluation criteria are intended to apply equally to the design of new facilities and to the evaluation of existing facilities. In addition, the criteria are intended to cover design and evaluation of buildings, equipment, piping, and other structures. Four separate sets of seismic design/evaluation criteria have been presented each with a different performance goal. In all these criteria, earthquake loading is selected from seismic hazard curves on a probabilistic basis but seismic response evaluation methods and acceptable behavior limits are deterministic approaches with which design engineers are familiar. For analytical evaluations, conservatism has been introduced through the use of conservative inelastic demand-capacity ratios combined with ductile detailing requirements, through the use of minimum specified material strengths and conservative code capacity equations, and through the use of a seismic scale factor. For evaluation by testing or by experience data, conservatism has been introduced through the use of an increase scale factor which is applied to the prescribed design/evaluation input motion

  9. Some problems in the acceptability of implementing radiation protection programs

    International Nuclear Information System (INIS)

    Neill, R.H.

    1997-01-01

    The three fundamentals that radiation protection programs are based upon are; 1) establishing a quantitative correlation between radiation exposure and biological effects in people; 2) determining a level of acceptable risk of exposure; and 3) establishing systems to measure the radiation dose to insure compliance with the regulations or criteria. The paper discusses the interrelationship of these fundamentals, difficulties in obtaining a consensus of acceptable risk and gives some examples of problems in identifying the most critical population-at-risk and in measuring dose. Despite such problems, it is recommended that we proceed with the existing conservative structure of radiation protection programs based upon a linear no threshold model for low radiation doses to insure public acceptability of various potential radiation risks. Voluntary compliance as well as regulatory requirements should continue to be pursued to maintain minimal exposure to ionizing radiation. (author)

  10. Study on Influencing Factor Analysis and Application of Consumer Mobile Commerce Acceptance

    Science.gov (United States)

    Li, Gaoguang; Lv, Tingjie

    Mobile commerce (MC) refers to e-commerce activities carried out using a mobile device such as a phone or PDA. With new technology, MC will be rapidly growing in the near future. At the present time, what factors making consumer accept MC and what MC applications are acceptable by consumers are two of hot issues both for MC providers and f or MC researchers. This study presents a proposed MC acceptance model that integrates perceived playfulness, perceived risk and cost into the TAM to study which factors affect consumer MC acceptance. The proposed model includes five variables, namely perceived risk, cost, perceived usefulness, perceived playfulness, perceived ease of use, perceived playfulness. Then, using analytic hierarchy process (AHP) to calculate weight of criteria involved in proposed model. Finally, the study utilizes fuzzy comprehensive evaluation method to evaluate MC applications accepted possibility, and then a MC application is empirically tested using data collected from a survey of MC consumers.

  11. Preliminary waste acceptance criteria for the ICPP spent fuel and waste management technology development program

    International Nuclear Information System (INIS)

    Taylor, L.L.; Shikashio, R.

    1993-09-01

    The purpose of this document is to identify requirements to be met by the Producer/Shipper of Spent Nuclear Fuel/High-LeveL Waste SNF/HLW in order for DOE to be able to accept the packaged materials. This includes defining both standard and nonstandard waste forms

  12. A proposed acceptance process for commercial off-the-shelf (COTS) software in reactor applications

    International Nuclear Information System (INIS)

    Preckshot, G.G.; Scott, J.A.

    1996-03-01

    This paper proposes a process for acceptance of commercial off-the-shelf (COTS) software products for use in reactor systems important to safety. An initial set of four criteria establishes COTS software product identification and its safety category. Based on safety category, three sets of additional criteria, graded in rigor, are applied to approve/disapprove the product. These criteria fall roughly into three areas: product assurance, verification of safety function and safety impact, and examination of usage experience of the COTS product in circumstances similar to the proposed application. A report addressing the testing of existing software is included as an appendix

  13. Seismic design and evaluation criteria for DOE facilities (DOE-STD-1020-XX)

    International Nuclear Information System (INIS)

    Short, S.A.; Kennedy, R.P.; Murray, R.C.

    1993-01-01

    Seismic design and evaluation criteria for DOE facilities are provided in DOE-STD-1020-XX. The criteria include selection of design/evaluation seismic input from probabilistic seismic hazard curves combined with commonly practiced deterministic response evaluation methods and acceptance criteria with controlled levels of conservatism. Conservatism is intentionally introduced in specification of material strengths and capacities, in the allowance of limited inelastic behavior and by a seismic load factor. These criteria are based on the performance or risk goals specified in DOE 5480.28. Criteria have been developed following a graded approach for several performance goals ranging from that appropriate for normal-use facilities to that appropriate for facilities involving hazardous or critical operations. Performance goals are comprised of desired behavior and of the probability of not achieving that behavior. Following the seismic design/evaluation criteria of DOE-STD-1020-XX is sufficient to demonstrate that the probabilistic performance or risk goals are achieved. The criteria are simple procedures but with a sound, rigorous basis for the achievement of goals

  14. An open trial of Acceptance-based Separated Family Treatment (ASFT) for adolescents with anorexia nervosa.

    Science.gov (United States)

    Timko, C Alix; Zucker, Nancy L; Herbert, James D; Rodriguez, Daniel; Merwin, Rhonda M

    2015-06-01

    Family based-treatments have the most empirical support in the treatment of adolescent anorexia nervosa; yet, a significant percentage of adolescents and their families do not respond to manualized family based treatment (FBT). The aim of this open trial was to conduct a preliminary evaluation of an innovative family-based approach to the treatment of anorexia: Acceptance-based Separated Family Treatment (ASFT). Treatment was grounded in Acceptance and Commitment Therapy (ACT), delivered in a separated format, and included an ACT-informed skills program. Adolescents (ages 12-18) with anorexia or sub-threshold anorexia and their families received 20 treatment sessions over 24 weeks. Outcome indices included eating disorder symptomatology reported by the parent and adolescent, percentage of expected body weight achieved, and changes in psychological acceptance/avoidance. Half of the adolescents (48.0%) met criteria for full remission at the end of treatment, 29.8% met criteria for partial remission, and 21.3% did not improve. Overall, adolescents had a significant reduction in eating disorder symptoms and reached expected body weight. Treatment resulted in changes in psychological acceptance in the expected direction for both parents and adolescents. This open trial provides preliminary evidence for the feasibility, acceptability, and efficacy of ASFT for adolescents with anorexia. Directions for future research are discussed. Copyright © 2015 Elsevier Ltd. All rights reserved.

  15. The Predictive Value of Selection Criteria in an Urban Magnet School

    Science.gov (United States)

    Lohmeier, Jill Hendrickson; Raad, Jennifer

    2012-01-01

    The predictive value of selection criteria on outcome data from two cohorts of students (Total N = 525) accepted to an urban magnet high school were evaluated. Regression analyses of typical screening variables (suspensions, absences, metropolitan achievement tests, middle school grade point averages [GPAs], Matrix Analogies test scores, and…

  16. Idaho National Engineering Laboratory release criteria for decontamination and decommissioning

    International Nuclear Information System (INIS)

    Dolenc, M.R.; Case, M.J.

    1986-01-01

    Criteria have been developed for release of Idaho National Engineering Laboratory (INEL) facilities and land areas following decontamination and decommissioning (D and D). Decommissioning release criteria in the form of dose guidelines were proposed by the US Nuclear Regulatory Commission as early as 1980. These criteria were used on an interim basis for INEL D and D projects. However, dose guidelines alone do not adequately cover the criteria necessary to release sites for unrestricted use. In actual practice, other parameters such as pathways analyses, sampling and instrumentation techniques, and implementation procedures are required to develop the basis for unrestricted release of a site. Thus, a rigorous approach for evaluating these other parameters is needed to develop acceptable D and D release criteria. Because of the complex and sensitive nature of the dose and pathways analyses work, a thorough review by experts in those respective fields was desired. Input and support in preparing or reviewing each part of the criteria development task was solicited from several DOE field offices. Experts were identified and contracted to assist in preparing portions of the release criteria, or to serve on a peer-review committee. Thus, the entire release criteria development task was thoroughly reviewed by recognized experts from each DOE field office, to validate technical content of the INEL site-specific document

  17. Extending the foreign spent fuel acceptance program: Policy and implementation issues

    International Nuclear Information System (INIS)

    Lyman, Edwin S.

    2005-01-01

    The May 2006 expiration date of the Foreign Research Reactor Spent Nuclear Fuel (FRR SNF) Acceptance Program is fast approaching. In April 2004, Energy Secretary Spencer Abraham instructed the Energy Department to 'initiate actions necessary to extend .... the fuel acceptance deadline'. However, extending the deadline may not be a simple task. The limits on the original program resulted from a delicate negotiation among many stakeholders. Any proposal to increase the duration and scope of the program will have to be considered in the context of DOE's failure since 1996 to develop viable treatment, packaging and long-term disposal options for FRR SNF. It is also unclear whether accepting additional low-enriched uranium FRR SNF can be justified on security grounds. This paper will propose criteria for acceptance of spent fuel under an extension that are intended to minimize controversy and ensure consistency with a threat-based prioritization of homeland security expenditures. (author)

  18. Establishing endangered species recovery criteria using predictive simulation modeling

    Science.gov (United States)

    McGowan, Conor P.; Catlin, Daniel H.; Shaffer, Terry L.; Gratto-Trevor, Cheri L.; Aron, Carol

    2014-01-01

    Listing a species under the Endangered Species Act (ESA) and developing a recovery plan requires U.S. Fish and Wildlife Service to establish specific and measurable criteria for delisting. Generally, species are listed because they face (or are perceived to face) elevated risk of extinction due to issues such as habitat loss, invasive species, or other factors. Recovery plans identify recovery criteria that reduce extinction risk to an acceptable level. It logically follows that the recovery criteria, the defined conditions for removing a species from ESA protections, need to be closely related to extinction risk. Extinction probability is a population parameter estimated with a model that uses current demographic information to project the population into the future over a number of replicates, calculating the proportion of replicated populations that go extinct. We simulated extinction probabilities of piping plovers in the Great Plains and estimated the relationship between extinction probability and various demographic parameters. We tested the fit of regression models linking initial abundance, productivity, or population growth rate to extinction risk, and then, using the regression parameter estimates, determined the conditions required to reduce extinction probability to some pre-defined acceptable threshold. Binomial regression models with mean population growth rate and the natural log of initial abundance were the best predictors of extinction probability 50 years into the future. For example, based on our regression models, an initial abundance of approximately 2400 females with an expected mean population growth rate of 1.0 will limit extinction risk for piping plovers in the Great Plains to less than 0.048. Our method provides a straightforward way of developing specific and measurable recovery criteria linked directly to the core issue of extinction risk. Published by Elsevier Ltd.

  19. International Political Actorness of the European Union: Evaluation Criteria

    Directory of Open Access Journals (Sweden)

    GNATYUK N.N.

    2014-06-01

    Full Text Available The European Union is a completely new international entity which is hard to evaluate using traditional criteria of political actorness. Its active international presence stimulates the modeling of international actor features beyond the scope of “state-international organization” scheme. The concept of international actorness serves as a starting point for the development of appropriate analytical model. Unlike the traditional state-centered approaches which define an international actor through its affiliation witch the international system, this concept operates at the internal level of international entity and at the international structure level. Furthermore, both of these levels are treated as ontologically neutral and mutually constitutive. This basic theoretical scheme is used for elaboration of evaluation criteria of political actorness. The proposed system of criteria is based on drawing, synthesizing and developing the main writings on “new international actors” since the times of classic work by Carol A. Cosgrove and Kenneth J. Twitchett. The key elements of actorness assessed in this article include defining of capacity to act on the global scene as well as the acceptance by other actors and by international system as a whole. At the internal level, the EU’s actor capacity is measured by assessing its core elements ranging from core aspects, such as autonomy, authority, actor capability, coherence and cohesion to identity aspects. On the external level, the decisive criteria are recognition and acceptance by others which reflect expectations and perceptions of the EU. The proposed approach of evaluating the international actorness enables us to consider the political activity of the EU on the basis of coordinated system of interaction between the variables of international and domestic levels of the analysis. Furthermore, this contributes to the development of cumulative, coherent, and comprehensive theory of international

  20. MULTIPLE CRITERIA DECISION MAKING IN STRATEGIC PLANNING OF TABLE EGG PRODUCTION

    Directory of Open Access Journals (Sweden)

    Ana Crnčan

    2016-06-01

    Full Text Available The main research objective was to analyze and evaluate different systems of table egg production by using the multiple criteria analysis, the method of Analytic Hierarchy Process (AHP in decision making within strategic planning of production. The survey involved 79 producers of table eggs registered in the Records on laying hens’ farms in the Republic of Croatia. In the first stage, the research defined the criteria and sub-criteria for system evaluation which were compared in pairs in order to determine the weight or importance for each of them. Alternatives were evaluation based on definition of priorities of examinees and the extent to which they meet each of the defined criteria and sub-criteria. Intensity of examinees’ preferences were entered into the Expert Choice software in order to evaluate ranking results of egg production systems. Defined model consisted of a quantitative criterion of economic indicators, and the other two referred to qualitative criteria, market indicators and technical-technological factors. Each criterion had its corresponding sub-criteria that were evenly distributed in numerical order. Based on individual assessments of the examinees, overall cumulative evaluation was obtained for the table egg production systems. Accordingly, the most acceptable alternative to egg production is the indoor keeping system (priority 0.301. It is followed by the free-range system of keeping laying hens (priority 0.253. The third-ranked alternative is egg production by hens kept in conventional cages (priority 0.226, while the fourth-ranked least acceptable alternative, as of the total evaluation, is the ecological system of egg production (priority 0.220. Taking into account the obtained results of multiple criteria evaluation as well as EU and world trends in changing consumers’ habits including food safety and quality as well as customers’ preferences towards local market and local products, it is recommended that eggs

  1. Advances in seismic criteria to qualify structures, systems and components in operating reactors

    International Nuclear Information System (INIS)

    Manrique, M.A.; Bak, W.R.

    1989-01-01

    This paper describes improved seismic evaluation criteria and analysis methodologies used as part of the seismic reevaluation of San Onofre Nuclear Generating Station, Unit 1. The plant had originally been designed for 0.25 g ground acceleration and was required to be upgraded to a 0.67 g ground acceleration as part of the plant's Long Term Service Seismic Reevaluation Program. The application of the criteria and methods described in this paper to demonstrate the seismic capability of the plant resulted in efficient plant modifications with considerable cost savings to the plant owner. The NRC accepted these criteria and methods based on favorable results of reviews, audits and independent verification of the theories, bases and implementation procedures of the proposed criteria and analysis methods

  2. Nuclear reactor philosophy and criteria

    International Nuclear Information System (INIS)

    Atchison, R.J.

    1979-07-01

    Nuclear power plant safety criteria and principles developed in Canada are directed towards minimizing the chance of failure of the fuel and preventing or reducing to an acceptably low level the escape of fission products should fuel failure occur. Safety criteria and practices are set forth in the Reactor Siting Guide, which is based upon the concept of defence in depth. The Guide specifies that design and construction shall follow the best applicable code, standard or practice; the total of all serious process system failures shall not exceed one in three years; special safety systems are to be physically and functionally separate from process systems and each other; and safety systems shall be testable, with unavailability less than 10 - 3 . Doses to the most exposed member of the public due to normal operation, serious process failures, and dual failures are specified. Licensees are also required to consider the effects of extreme conditions due to airplane crashes, explosions, turbine disintegration, pipe burst, and natural disasters. Safety requirements are changing as nuclear power plant designs evolve and in response to social and economic pressures

  3. Most Scottish neurologists do not apply the 2010 McDonald criteria when diagnosing multiple sclerosis.

    Science.gov (United States)

    Lumley, R; Davenport, R; Williams, A

    2015-03-01

    The diagnostic criteria for multiple sclerosis have evolved over time and currently the 2010 McDonald criteria are the most widely accepted. These criteria allow the diagnosis of multiple sclerosis to be made at the clinically isolated syndrome stage provided certain criteria are met on a single magnetic resonance brain scan. Our hypothesis was that neurologists in Scotland did not use these criteria routinely. We sent a SurveyMonkey questionnaire to all Scottish neurologists (consultants and trainees) regarding the diagnosis of multiple sclerosis. Our questionnaire response rate was 65/99 (66%). Most Scottish neurologists were aware of the criteria and 31/58 (53%) felt that they were using these routinely. However, in a clinical vignette designed to test the application of these criteria, only 5/57 (9%) of neurologists appeared to use them. Scottish neurologists' use of the 2010 McDonald criteria for diagnosis of multiple sclerosis varies from practitioners' perception of their use of these criteria.

  4. Acceptance-criteria for the bedrock for deep geologic disposal of spent nuclear fuel. Proceedings from a seminar at Gothenburg University

    International Nuclear Information System (INIS)

    1995-11-01

    The seminar was directed to Nordic participants, and discussed disposal in the Nordic crystalline bedrock. Criteria for the bedrock should include: It should give durable mechanical protection for the engineered barriers; give a stable and favorable chemical environment for these barriers; have a low turnover of ground water in the near field; be easy to characterize; give favorable recipient-conditions; not have valuable minerals in workable quantities. These general criteria raise several questions coupled to the safety analysis: e.g. the need for geological, hydrological and geochemical parameters. Which data are missing, which are most difficult to find? What should the site characterization program look like to focus on factors that are of the highest importance according to the safety analysis. The demands on the conditions at a site need to be translated into quantitative criteria, which should be expressed as values that can be measured at the site or deduced from such measurements. These questions were discussed at the seminar, and 21 contributions from Finnish, Norwegian and Swedish participants are reported in these proceedings under the chapters: Coupling to the safety analysis; Methodology and criteria for site selection in a regional geoscientific perspective; Rock as a building material - prognosis and result; Geoscientific criteria for the bedrock at the repository - Mechanical protection; Geoscientific criteria for the bedrock at the repository - Low ground water turnover, chemically favorable and stable environment in the near field; Geoscientific criteria for the bedrock at the repository - Demands on the bedrock concerning the migration of radionuclides

  5. Proposed approach to derivation of acceptance criteria for disposal of disused sealed sources mixed with other accepted wastes in near-surface repository

    International Nuclear Information System (INIS)

    Salzer, P.; Stefula, V.; Homola, J.

    2003-01-01

    The Mochovce repository is described in the report. It is vault type near surface repository with 80 concrete vaults (2x2x20), 90 FRC containers (3.1 m 3 ) in one vault (3x10x3), compacted clay bath-tub around double row. 300 years of institutional control are envisioned.The following scenarios are examined: Normal evolution scenario; Alternative evolution scenarios (perforated clay barrier; well in close proximity); Intruder scenarios (construction of simple dwelling; construction of multi-storey building; construction of road; residence scenario). It is being proposed that the DSSs are disposed of in the containers together with normal operational waste. Long-lived alpha emitters - excluded a priori (e.g. 226 Ra); Short-lived (T 1/2 = 10 2 days) radionuclides - interim stored until decayed down to clearance level 60 Co - no activity limit, with due consideration of operational safety. The DSSs disposal issue is thus reduced to the disposal of 137 Cs. No limit has been imposed on total activity. Existing limits for operational waste: 3.13.10 13 Bq / container in the upper layer; 3.41.10 13 Bq / container in the bottom or intermediate layer. The acceptance criteria are assessed according to the risk. Two are models set up in MicroShield ver. 5.0. Homogenous source of 137 Cs in cubic concrete container and point source (hot spot) of the same activity. The result is - dose from the point source is 16.6 times higher than the one from the cube. As a result the following new restrictions arise for disposal of the 137 Cs spent industrial sources: disposal of DSSs is forbidden in the upper layer of the containers; maximum activity of the 137 Cs disused industrial source emplaced into the FRC container is 3.41x10 13 / 16.6 = 2.05x10 12 Bq in case of FRC filling by non-radioactive cement mortar; if the cemented radioactive waste is to be used for filling of FRC, decrease of the limit for the disused sealed source is equivalent to the radioactivity of the cement mixture

  6. Containment design, performance criteria and research needs for advanced reactor designs

    International Nuclear Information System (INIS)

    Bagdi, G.; Ali, S.; Costello, J

    2004-01-01

    This paper points out some important shifts in the basic expectations in the performance requirements for containment structures and discusses the areas where the containment structure design requirements and acceptance criteria can be integrated with ultimate test based insights. Although there has not been any new reactor construction in the United States for over thirty years, several designs of evolutionary and advanced reactors have already been certified. Performance requirements for containment structures under design basis and severe accident conditions and explicit consideration of seismic margins have been used in the design certification process. In the United States, the containment structure design code is the American Society of Mechanical Engineers, Boiler and Pressure Vessel Code, Section III, Division 1, Subsection NE-Class MC for the steel containment and Section III, Division 2 for reinforced and prestressed concrete reactor vessels and containments. This containment design code was based on the early concept of applying design basis internal pressure and associated load combinations that included the operating basis and safe shutdown earthquake ground motion. These early design criteria served the nuclear industry and the regulatory authorities in maintaining public health and safety. However, these early design criteria do not incorporate the performance criteria related to containment function in an integrated fashion. Research in large scale model testing of containment structures to failure from over pressurization and shake table testing using simulated ground motion, have produced insights related to failure modes and material behavior at failure. The results of this research provide the opportunity to integrate these observations into design and acceptance criteria. This integration process would identify 'gaps' in the present knowledge and future research needs. This knowledge base is important for gleaning risk-informed insights into

  7. Predicting nurses' use of healthcare technology using the technology acceptance model: an integrative review.

    Science.gov (United States)

    Strudwick, Gillian

    2015-05-01

    The benefits of healthcare technologies can only be attained if nurses accept and intend to fully use them. One of the most common models utilized to understand user acceptance of technology is the Technology Acceptance Model. This model and modified versions of it have only recently been applied in the healthcare literature among nurse participants. An integrative literature review was conducted on this topic. Ovid/MEDLINE, PubMed, Google Scholar, and CINAHL were searched yielding a total of 982 references. Upon eliminating duplicates and applying the inclusion and exclusion criteria, the review included a total of four dissertations, three symposium proceedings, and 13 peer-reviewed journal articles. These documents were appraised and reviewed. The results show that a modified Technology Acceptance Model with added variables could provide a better explanation of nurses' acceptance of healthcare technology. These added variables to modified versions of the Technology Acceptance Model are discussed, and the studies' methodologies are critiqued. Limitations of the studies included in the integrative review are also examined.

  8. 105 K East isolation barrier acceptance analysis report

    International Nuclear Information System (INIS)

    McCracken, K.J.; Irwin, J.J.

    1995-01-01

    The objective of this document is to report and interpret the findings of the isolation barrier acceptance tests performed in 105KE/100K. The tests were performed in accordance with the test plan (McCracken 1995c) and acceptance test procedure (McCracken 1995a). The test report (McCracken 1995b) contains the test data. This document compares the test data (McCracken 1995b) against the criteria (McCracken 1995a, c). A discussion of the leak rate analytical characterization (Irwin 1995) describes how the flow characteristics and the flow rate will be determined using the test data from the test report (McCracken 1995b). The barriers must adequately control the leakage from the main basin to the discharge chute to less than the 1,500 gph (5,680 lph) Safety Analysis Report (SAR 1994) limit

  9. Design requirements, criteria and methods for seismic qualification of CANDU power plants

    International Nuclear Information System (INIS)

    Singh, N.; Duff, C.G.

    1979-10-01

    This report describes the requirements and criteria for the seismic design and qualification of systems and equipment in CANDU nuclear power plants. Acceptable methods and techniques for seismic qualification of CANDU nuclear power plants to mitigate the effects or the consequences of earthquakes are also described. (auth)

  10. Criteria and principles for environmental assessment of disposal of radioactive wastes

    International Nuclear Information System (INIS)

    Hill, M.D.

    1989-01-01

    This paper describes the criteria which are used in judging whether methods for the disposal of radioactive wastes are acceptable, from a radiological protection point of view, and the principles used in assessing the radiological impact of waste disposal methods. Gaseous, liquid and solid wastes are considered, and the discussion is relevant to wastes arising from the nuclear power industry, and from medical practices, general industry and research. Throughout the paper, emphasis is given to the general criteria and principles recommended by international organizations rather than to the detailed legislative and regulatory requirements in particular countries

  11. Protection criteria from the non-ionizing radiations

    International Nuclear Information System (INIS)

    Touzet, Rodolfo E.

    2004-01-01

    The first objective of the protection philosophy is to determinate the relation reason-effect in order to establish the exposition thresholds to acceptable values. To establish the radioprotection criteria is important to considerate the following: a-) The damage and effects of the non-ionizing radiation; b-) The physical aspects of the fields exposition; and c-) The dosimetry of the involucrate tissues. The non-ionizing radiation includes the optics radiations (ultraviolet, visible, infrared and laser), and the electromagnetic radiations (microwave, radars, magnetic and electrostatics fields)

  12. Failure Modes of thin supported Membranes

    DEFF Research Database (Denmark)

    Hendriksen, Peter Vang; Høgsberg, J.R.; Kjeldsen, Ane Mette

    2007-01-01

    Four different failure modes relevant to tubular supported membranes (thin dense films on a thick porous support) were analyzed. The failure modes were: 1) Structural collapse due to external pressure 2) burst of locally unsupported areas, 3) formation of surface cracks in the membrane due to TEC......-mismatches, and finally 4) delamination between membrane and support due to expansion of the membrane on use. Design criteria to minimize risk of failure by the four different modes are discussed. The theoretical analysis of the two last failure modes is compared to failures observed on actual components....

  13. Ecological radiation protection criteria for nuclear power

    International Nuclear Information System (INIS)

    Kryshev, I.I.

    1993-01-01

    By now a large quantity of radioactive hazards of all sizes and shapes has accumulated in Russia. They include RBMK, VVER, and BN (fast-neutron) nuclear power plants, nuclear fuel processing plants, radioactive waste dumps, ships with nuclear power units, etc. In order to evaluate the radioecological situation correctly, the characteristics of the radioactive contamination must be compiled in these areas with some system of criteria which will provide an acceptable level of ecological safety. Currently health criteria for radiation protection are, which are oriented to man's radiation protection, predominate. Here the concept of a thresholdless linear dose-response dependence, which has been confirmed experimentally only at rather high doses (above 1 Gy), is taken as the theoretical basis for evaluating and normalizing radiation effects. According to one opinion, protecting people against radiation is sufficient to protect other types of organisms, although they are not necessarily of the same species. However, from the viewpoint of ecology, this approach is incorrect, because it does not consider radiation dose differences between man and other living organisms. The article discusses dose-response dependences for various organisms, biological effects of ionizing radiation, and appropriate radiation protection criteria

  14. Acceptance of cosmetic surgery, body appreciation, body ideal internalization, and fashion blog reading among late adolescents in Sweden.

    Science.gov (United States)

    Lunde, Carolina

    2013-09-01

    This study examined adolescents' attitudes of cosmetic surgery, as well as the relationships between these attitudes, body appreciation, body ideal internalization, and fashion blog reading. The sample comprised 110 (60 boys, 50 girls) late adolescents (mean age 16.9 years) from a Swedish high school. The results indicated that younger adolescents seem somewhat more accepting of cosmetic surgery. This was especially the case for boys' acceptance of social motives for obtaining cosmetic surgery (boys' M=2.3±1.55 vs. girls' M=1.7±0.89). Girls', and to a limited extent boys', internalization of the thin ideal was related to more favorable cosmetic surgery attitudes. Athletic ideal internalization and body appreciation were unrelated to these attitudes. Finally, girls who frequently read fashion blogs reported higher thin ideal internalization, and also demonstrated a slight tendency of more cosmetic surgery consideration. Copyright © 2013 Elsevier Ltd. All rights reserved.

  15. Protocol for the verification of minimum criteria

    International Nuclear Information System (INIS)

    Gaggiano, M.; Spiccia, P.; Gaetano Arnetta, P.

    2014-01-01

    This Protocol has been prepared with reference to the provisions of article 8 of the Legislative Decree of May 26, 2000 No. 187. Quality controls of radiological equipment fit within the larger 'quality assurance Program' and are intended to ensure the correct operation of the same and the maintenance of that State. The pursuit of this objective guarantees that the radiological equipment subjected to those controls also meets the minimum criteria of acceptability set out in annex V of the aforementioned legislative decree establishing the conditions necessary to allow the functions to which each radiological equipment was designed, built and for which it is used. The Protocol is established for the purpose of quality control of radiological equipment of Cone Beam Computer Tomography type and reference document, in the sense that compliance with stated tolerances also ensures the subsistence minimum acceptability requirements, where applicable.

  16. Radioactive waste management: review on clearance levels and acceptance criteria legislation, requirements and standards.

    Science.gov (United States)

    Maringer, F J; Suráň, J; Kovář, P; Chauvenet, B; Peyres, V; García-Toraño, E; Cozzella, M L; De Felice, P; Vodenik, B; Hult, M; Rosengård, U; Merimaa, M; Szücs, L; Jeffery, C; Dean, J C J; Tymiński, Z; Arnold, D; Hinca, R; Mirescu, G

    2013-11-01

    In 2011 the joint research project Metrology for Radioactive Waste Management (MetroRWM)(1) of the European Metrology Research Programme (EMRP) started with a total duration of three years. Within this project, new metrological resources for the assessment of radioactive waste, including their calibration with new reference materials traceable to national standards will be developed. This paper gives a review on national, European and international strategies as basis for science-based metrological requirements in clearance and acceptance of radioactive waste. © 2013 Elsevier Ltd. All rights reserved.

  17. Engineering study of generic site criteria for selected DOE plutonium facilities

    International Nuclear Information System (INIS)

    Kingsbury, R.J.; Greenwood, J.M.; Sandoval, M.D.

    1980-09-01

    The objectives of this study were to identify criteria that would be applied to selection of a site for plutonium facilities such as those at the Rocky Flats Plant, to establish the relative importance of these criteria, and to identify suitable areas within the United States for location of plutonium facilities with respect to these criteria. Sources of the site criteria identified include federal laws, federal agency regulations, state laws and regulations, and requirements associated with operations to be performed at the site. The criteria identified during the study were organized into 14 major categories. The relative importnace of each category and each criterion within the categories were established using group decision-making techniques. The major criteria categories, their assigned weight on a scale of 1 to 10, and their relative priority ranks are as follows: geology/seismicity; public safety; environmental impact; meteorology; hydrology; topography; transportation; utilities; personnel; safeguards/security; land area and availability; land use compatibility; and, public acceptance. A suitability analysis of the continental United States was performed using only those criteria that could be mapped at a national scale. Suitability was assessed with respect to each of these criteria, and individual suitability maps were prepared. A composite suitability map was generated using computerized overlay techniques. This map provides a starting point for identifying specific candidate sites if an actual site selection were to be conducted

  18. Suggested non-proliferation criteria for commercial nuclear fuel cycles

    International Nuclear Information System (INIS)

    Laney, R.V.; Heubotter, P.R.

    1978-01-01

    Based on the Administration's policy to prevent nuclear weapons proliferation through diversion of fuel from commercial reactor fuel cycles, a ''benchmark'' set of nonproliferation criteria was prepared for the commercial nuclear fuel cycle. These criteria should eliminate incremental risks of proliferation beyond those inherent in the present generation of low-enriched-uranium-fueled reactors operating in a once-through mode, with internationally safeguarded storage of spent fuel. They focus on the balanced application of technical constraints consistent with the state of the technology, with minimal requirements for institutional constraints, to provide a basis for assessing the proliferation resistance of proposed fission power systems. The paper contains: (1) our perception of the nuclear energy policy and of the baseline proliferation risk accepted under this policy; (2) objectives for a reactor and fuel cycle strategy which address the technical, political, and institutional aspects of diversion and proliferation and, at the same time, satisfy the Nation's needs for efficient, timely, and economical utilization of nuclear fuel resources; (3) criteria which are responsive to these objectives and can therefore be used to screen proposed reactor and fuel cycle strategies; and (4) a rationale for these criteria

  19. 105K West Isolation Barrier Acceptance Test results

    International Nuclear Information System (INIS)

    McCracken, K.J.; Irwin, J.J.

    1995-01-01

    The objective of this document is to report and interpret the findings of the isolation barrier acceptance tests performed in 105KW/100K. The tests were performed in accordance with the test plan and acceptance test procedure. The test report contains the test data. This document compares the test data against the criteria. A discussion of the leak rate analytical characterization describes how the flow characteristics flow rate will be determined using the test data from the test report. Two modes of water loss were considered; basin and/or discharge chute leakage, and evaporation. An initial test established baseline leakage data and instrumentation performance. Test 2 evaluated the sealing performance of the isolation barrier by inducing an 11 in. (27.9 cm) level differential across the barrier. The leak rate at this 11 in. (27.9 cm) level is extrapolated to the 16 ft. (4.9 m) level differential postulated in the DBE post seismic event. If the leak rate, adjusted for evaporation and basin leakage (determined from Test 1), is less than the SAR limit of 1,500 gph (5,680 lph) at a 16 ft (4.9 m) level differential, the barriers pass the acceptance test

  20. Quality of laboratory studies assessing effects of Bt-proteins on non-target organisms: minimal criteria for acceptability.

    Science.gov (United States)

    De Schrijver, Adinda; Devos, Yann; De Clercq, Patrick; Gathmann, Achim; Romeis, Jörg

    2016-08-01

    The potential risks that genetically modified plants may pose to non-target organisms and the ecosystem services they contribute to are assessed as part of pre-market risk assessments. This paper reviews the early tier studies testing the hypothesis whether exposure to plant-produced Cry34/35Ab1 proteins as a result of cultivation of maize 59122 is harmful to valued non-target organisms, in particular Arthropoda and Annelida. The available studies were assessed for their scientific quality by considering a set of criteria determining their relevance and reliability. As a case-study, this exercise revealed that when not all quality criteria are met, weighing the robustness of the study and its relevance for risk assessment is not obvious. Applying a worst-case expected environmental concentration of bioactive toxins equivalent to that present in the transgenic crop, confirming exposure of the test species to the test substance, and the use of a negative control were identified as minimum criteria to be met to guarantee sufficiently reliable data. This exercise stresses the importance of conducting studies meeting certain quality standards as this minimises the probability of erroneous or inconclusive results and increases confidence in the results and adds certainty to the conclusions drawn.

  1. IMPORTANCE OF MULTIPLE CRITERIA FOR PRIORITY SETTING OF HIV/AIDS INTERVENTIONS.

    Science.gov (United States)

    Tromp, Noor; Prawiranegara, Rozar; Siregar, Adiatma; Sunjaya, Deni; Baltussen, Rob

    2015-01-01

    This study describes the views of various stakeholders on the importance of different criteria for priority setting of HIV/AIDS interventions in Indonesia. Based on a general list of criteria and a focus group discussion with stakeholders (n = 6), a list was developed of thirty-two criteria that play a role in priority setting in HIV/AIDS control in West-Java province. Criteria were categorized according to the World Health Organization's health system goals and building block frameworks. People living with HIV/AIDS (n = 49), healthcare workers (HCW) (n = 41), the general population (n = 43), and policy makers (n = 22) rated the importance of thirty-two criteria on a 5-point Likert-scale. Thereafter, respondents ranked the highest rated criteria to express more detailed preferences. Stakeholders valued the following criteria as most important for the priority setting of HIV/AIDS interventions: an intervention's impact on the HIV/AIDS epidemic, reduction of stigma, quality of care, effectiveness on individual level, and feasibility in terms of current capacity of the health system (i.e., HCW, product, information, and service requirements), financial sustainability, and acceptance by donors. Overall, stakeholders' preferences for the importance of criteria are similar. Our study design outlines an approach for other settings to identify which criteria are important for priority setting of health interventions. For Indonesia, these study results may be used in priority setting processes for HIV/AIDS control and may contribute to more transparent and systematic allocation of resources.

  2. 40 CFR 80.584 - What are the precision and accuracy criteria for approval of test methods for determining the...

    Science.gov (United States)

    2010-07-01

    ... criteria for approval of test methods for determining the sulfur content of motor vehicle diesel fuel, NRLM....584 What are the precision and accuracy criteria for approval of test methods for determining the... available gravimetric sulfur standard in the range of 1-10 ppm sulfur shall not differ from the accepted...

  3. The Rayleigh law in silicon doped hafnium oxide ferroelectric thin films

    Energy Technology Data Exchange (ETDEWEB)

    Guan, Yan; Liu, Xiaohua [Key Laboratory of Materials Modification by Laser, Ion, and Electron Beams (Ministry of Education), School of Materials Science and Engineering, Dalian University of Technology, Dalian (China); Zhou, Dayu [Key Laboratory of Materials Modification by Laser, Ion, and Electron Beams (Ministry of Education), School of Materials Science and Engineering, Dalian University of Technology, Dalian (China); State Key Laboratory of Electronic Thin Films and Integrated Devices, University of Electronic Science and Technology of China, Chengdu (China); Xu, Jin [Department of Electronic Engineering, Dalian Neusoft University of Information, Dalian (China); Cao, Fei; Dong, Xianlin [Key Laboratory of Inorganic Functional Materials and Devices, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai (China); Mueller, Johannes [Fraunhofer IPMS-CNT, Dresden (Germany); Schenk, Tony; Schroeder, Uwe [NaMLab gGmbH/TU Dresden (Germany)

    2015-10-15

    A wealth of studies have confirmed that the low-field hysteresis behaviour of ferroelectric bulk ceramics and thin films can be described using Rayleigh relations, and irreversible domain wall motion across the array of pining defects has been commonly accepted as the underlying micro-mechanism. Recently, HfO{sub 2} thin films incorporated with various dopants were reported to show pronounced ferroelectricity, however, their microscopic domain structure remains unclear till now. In this work, the effects of the applied electric field amplitude, frequency and temperature on the sub-coercive polarization reversal properties were investigated for 10 nm thick Si-doped HfO{sub 2} thin films. The applicability of the Rayleigh law to ultra-thin ferroelectric films was first confirmed, indicating the existence of a multi-domain structure. Since the grain size is about 20-30 nm, a direct observation of domain walls within the grains is rather challenging and this indirect method is a feasible approach to resolve the domain structure. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  4. The Rayleigh law in silicon doped hafnium oxide ferroelectric thin films

    International Nuclear Information System (INIS)

    Guan, Yan; Liu, Xiaohua; Zhou, Dayu; Xu, Jin; Cao, Fei; Dong, Xianlin; Mueller, Johannes; Schenk, Tony; Schroeder, Uwe

    2015-01-01

    A wealth of studies have confirmed that the low-field hysteresis behaviour of ferroelectric bulk ceramics and thin films can be described using Rayleigh relations, and irreversible domain wall motion across the array of pining defects has been commonly accepted as the underlying micro-mechanism. Recently, HfO 2 thin films incorporated with various dopants were reported to show pronounced ferroelectricity, however, their microscopic domain structure remains unclear till now. In this work, the effects of the applied electric field amplitude, frequency and temperature on the sub-coercive polarization reversal properties were investigated for 10 nm thick Si-doped HfO 2 thin films. The applicability of the Rayleigh law to ultra-thin ferroelectric films was first confirmed, indicating the existence of a multi-domain structure. Since the grain size is about 20-30 nm, a direct observation of domain walls within the grains is rather challenging and this indirect method is a feasible approach to resolve the domain structure. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  5. Working draft regulatory guide on release criteria for decommissioning: NRC staff's draft for comment

    International Nuclear Information System (INIS)

    Daily, M.C.; Huffert, A.; Cardile, F.; Malaro, J.C.

    1994-08-01

    The Nuclear Regulatory Commission's (NRC) regulations in 10 CFR 20 are being amended to include radiological criteria for decommissioning of lands and structures at nuclear facilities. 10 CFR Part 20, Subpart E establishes criteria for the remediation of contaminated sites or facilities that will allow their release for future use with or without restrictions. The criteria include a Total Effective Dose Equivalent (TEDE) limit of 15 mrem/year (0.15 mSv/y) that should not be exceeded by an average individual among those who could potentially receive the greatest exposure from any residual activity within a facility or on a site. The criteria also require a licensee to reduce any residual radioactivity to as-low-as-reasonably-achievable (ALARA) levels. This staff draft guide describes acceptable procedures for determining the predicted dose level (PDL) from any residual radioactivity at the site. It describes the basic features of the calculational models and the associated default assumptions and parameter values the NRC staff would find acceptable in calculating PDLs. Appendices A, B, and C provide numerical values that can be used to estimate the dose from residual radioactivity remaining at a site. Since 10 CFR Part 20, Subpart E introduces several new concepts, definitions and discussions are included in a regulatory position concepts section of the guide to assist licensees in understanding some of the philosophy underlying the rule

  6. Attachment of lead wires to thin film thermocouples mounted on high temperature materials using the parallel gap welding process

    Science.gov (United States)

    Holanda, Raymond; Kim, Walter S.; Pencil, Eric; Groth, Mary; Danzey, Gerald A.

    1990-01-01

    Parallel gap resistance welding was used to attach lead wires to sputtered thin film sensors. Ranges of optimum welding parameters to produce an acceptable weld were determined. The thin film sensors were Pt13Rh/Pt thermocouples; they were mounted on substrates of MCrAlY-coated superalloys, aluminum oxide, silicon carbide and silicon nitride. The entire sensor system is designed to be used on aircraft engine parts. These sensor systems, including the thin-film-to-lead-wire connectors, were tested to 1000 C.

  7. Two-dimensional models for the optical response of thin films

    Science.gov (United States)

    Li, Yilei; Heinz, Tony F.

    2018-04-01

    In this work, we present a systematic study of 2D optical models for the response of thin layers of material under excitation by normally incident light. The treatment, within the framework of classical optics, analyzes a thin film supported by a semi-infinite substrate, with both the thin layer and the substrate assumed to exhibit local, isotropic linear response. Starting from the conventional three-dimensional (3D) slab model of the system, we derive a two-dimensional (2D) sheet model for the thin film in which the optical response is described by a sheet optical conductivity. We develop criteria for the applicability of this 2D sheet model for a layer with an optical thickness far smaller than the wavelength of the light. We examine in detail atomically thin semi-metallic and semiconductor van-der-Waals layers and ultrathin metal films as representative examples. Excellent agreement of the 2D sheet model with the 3D slab model is demonstrated over a broad spectral range from the radio frequency limit to the near ultraviolet. A linearized version of system response for the 2D model is also presented for the case where the influence of the optically thin layer is sufficiently weak. Analytical expressions for the applicability and accuracy of the different optical models are derived, and the appropriateness of the linearized treatment for the materials is considered. We discuss the advantages, as well as limitations, of these models for the purpose of deducing the optical response function of the thin layer from experiment. We generalize the theory to take into account in-plane anisotropy, layered thin film structures, and more general substrates. Implications of the 2D model for the transmission of light by the thin film and for the implementation of half- and totally absorbing layers are discussed.

  8. Criteria for permission of radiosterilized products to application in medicine; Zasady dopuszczania wyrobow sterylizowanych radiacyjnie do stosowania w medycynie

    Energy Technology Data Exchange (ETDEWEB)

    Achmatowicz, T [Instytut Lekow, Warsaw (Poland)

    1997-10-01

    The criteria being used in Poland for permission of radiosterilized medical materials to commercial application result from regulations being in force. The international regulations are also taken into account. The all criteria and procedure needed for any product become accepted for radiosterilization and commercial medical use have been presented and discussed. 1 tab.

  9. Key acceptability attributes of orodispersible films.

    Science.gov (United States)

    Scarpa, Mariagiovanna; Paudel, Amrit; Kloprogge, Frank; Hsiao, Wen Kai; Bresciani, Massimo; Gaisford, Simon; Orlu, Mine

    2018-04-01

    The features rendering orodispersible films (ODFs) patient-centric formulations are widely discussed in the scientific literature. However there is a lack of research studies exploring ODF characteristics with a potential impact on end-user acceptability. The aim of this study was to identify the key ODF characteristics affecting end-user acceptability by developing in vitro test methods for the prediction of ODFs acceptability and correlate these formulation characteristics with the data obtained from a human panel study. Four drug-free single-polymer films were prepared by solvent casting. Solutions of poly(vinyl) alcohol (PVOH) 39 KDa (P1), PVOH 197 KDa (P2), carboxymethylcellulose (CMC) 395 KDa (C1), and CMC 725 KDa (C2) were prepared. Texture analysis and Dynamic Mechanical Analysis (DMA) were used to assess film tack. Petri dish and drop methods were used to assess disintegration time. A human panel of 24 healthy young adults was employed to identify end-user acceptability criteria of the four study film samples. Texture analysis data of ODF tack were not found to be in agreement with the in vivo perceived stickiness in the mouth. However, measurement of the area under the adhesive force curve obtained by DMA correlated with in vivo perceived stickiness data for all samples. The disintegration times obtained by drop method were more comparable to human panel data than the petri dish method. Hence DMA and drop methods proved to be promising methodologies for the prediction of the end-user acceptability. The type and molecular weight of the film-forming polymer had a strong influence on stickiness perception, whereas only polymeric molecular weight influenced perceived disintegration time. The human panel study showed that Participant Reported Outcomes (PROs) for the perceived stickiness in the mouth and disintegration time of test films received significantly different scores between samples, and thus were identified as the key attributes with the

  10. Application fuzzy multi-attribute decision analysis method to prioritize project success criteria

    Science.gov (United States)

    Phong, Nguyen Thanh; Quyen, Nguyen Le Hoang Thuy To

    2017-11-01

    Project success is a foundation for project owner to manage and control not only for the current project but also for future potential projects in construction companies. However, identifying the key success criteria for evaluating a particular project in real practice is a challenging task. Normally, it depends on a lot of factors, such as the expectation of the project owner and stakeholders, triple constraints of the project (cost, time, quality), and company's mission, vision, and objectives. Traditional decision-making methods for measuring the project success are usually based on subjective opinions of panel experts, resulting in irrational and inappropriate decisions. Therefore, this paper introduces a multi-attribute decision analysis method (MADAM) for weighting project success criteria by using fuzzy Analytical Hierarchy Process approach. It is found that this method is useful when dealing with imprecise and uncertain human judgments in evaluating project success criteria. Moreover, this research also suggests that although cost, time, and quality are three project success criteria projects, the satisfaction of project owner and acceptance of project stakeholders with the completed project criteria is the most important criteria for project success evaluation in Vietnam.

  11. Microbiological criteria for good manufacturing practice (GMP)

    Energy Technology Data Exchange (ETDEWEB)

    Farkas, J [Inst. of Preservation and Livestock Products Technology, Univ. of Horticulture and Food Industry, Budapest (Hungary); Zukal, E [Inst. of Preservation and Livestock Products Technology, Univ. of Horticulture and Food Industry, Budapest (Hungary)

    1992-01-01

    Good manufacturing practice (GMP) consist of an effective manufacturing operation and an effective application of food control. GMP is best supported by the Hazard Analysis Critical Control Point system (HACCP) of the preventive quality assurance, which requires that food irradiation as any food processing technology should be used only with foods of an acceptable quality and adequate handling and storage procedures should precede and follow the processing. The paper concentrates on the first element of the HACCP system for an irradiation plant: the incoming product control, i.e. whether GMP of foods to be irradiated can be assessed by establishing microbiological criteria for their previous good manufacturing practice. In this regard, it summarizes considerations and findings of a ''Consultation on Microbiological Criteria for Foods to be Further Processed Including by Irradiation'' held in 1989 by the International Consultative Group on Food irradiation at the Headquarters of the World Health Organization, Geneva. Difficulties in establishing reference values and defining good manufacturing practices will be pointed out. (orig.)

  12. The Success Criteria of Scientific Pedagogic Activities

    Directory of Open Access Journals (Sweden)

    M. V. Ovchinnikov

    2013-01-01

    Full Text Available The paper considers the problem of scientific pedagogic activity assessment of the higher school academic staff. The existing options of quality estimation are listed along with their deficiencies; the most acceptable in the authors’ opinion being the systematic approach. The latter allows considering almost every aspect of scientific-pedagogic activity. On that ground, the authors recommend the following success estimation criteria: gnostic, projecting, communicative, informational, and organizational. The criteria of work satisfaction and its results are taken into consideration as additional ones. The indicators of each criterion are given demonstrating that the as- sessment can be both internal (subjective and external (objective, denoted in the normative acts. The problem of complex and just quality assessment of scientific- pedagogic activity is quite relevant as it affects the academic staff motivation. The authors believe that the research findings can improve the objectivity of teachers’ work assessment and give way to differentiated approaches to their motivation and stimulation. 

  13. Microbiological criteria for good manufacturing practice (GMP)

    International Nuclear Information System (INIS)

    Farkas, J.; Zukal, E.

    1992-01-01

    Good manufacturing practice (GMP) consist of an effective manufacturing operation and an effective application of food control. GMP is best supported by the Hazard Analysis Critical Control Point system (HACCP) of the preventive quality assurance, which requires that food irradiation as any food processing technology should be used only with foods of an acceptable quality and adequate handling and storage procedures should precede and follow the processing. The paper concentrates on the first element of the HACCP system for an irradiation plant: the incoming product control, i.e. whether GMP of foods to be irradiated can be assessed by establishing microbiological criteria for their previous good manufacturing practice. In this regard, it summarizes considerations and findings of a ''Consultation on Microbiological Criteria for Foods to be Further Processed Including by Irradiation'' held in 1989 by the International Consultative Group on Food irradiation at the Headquarters of the World Health Organization, Geneva. Difficulties in establishing reference values and defining good manufacturing practices will be pointed out. (orig.) [de

  14. A Method for Suppressing Superconductivity of Thin Films

    Science.gov (United States)

    Suppula, Tarmo; Pekola, Jukka; Kauppinen, Juha

    2003-03-01

    We have developed a method for suppressing superconductivity of thin films. Thin stripes of cobalt grown by e-gun evaporation and patterned by e-beam lithography were placed in the vicinity of aluminium thin film structures. The cobalt stripes were magnetized at 4.2 K with a superconducting coil and the remanence suppressed superconductivity of the Al stripe at temperatures down to 50 mK at least. The magnetization remained in thermal cycling and in a longer storage at room temperature. Motivation for this work is the Coulomb Blockade Thermometer(CBT)^1 which has to be in a normal state to operate. The CBT sensor contains aluminium which is superconducting at temperatures below 1.4 K. An external magnetic field is not always available or acceptable in cryostats. A small grain of permanent magnet mounted to the sensor is another solution, but suspicious if the sensor is put in strong magnetic fields or if "zero field" environment is required. We have shown that suitably patterned and magnetized Co stripes in the vicinity of tunnel junctions of the CBT can solve this problem. The amount of magnetic material in the sensor, as well as the stray field, is very small. This technique may be useful in other low temperature thin film devices also. 1) Product of Nanoway Ltd.

  15. Definition of criteria related to occupational exposure for use in multi-criteria decision making process for nuclear accidents in Brazil

    International Nuclear Information System (INIS)

    Silva, Diogo N.G.; Guimaraes, Jean R.D.; Rochedo, Elaine R.R.

    2013-01-01

    After the occurrence of nuclear or radiological accidents, the selection of strategies for remediation of contaminated areas and of protective measures for members of public should be based on previously established criteria. Hence, it becomes possible to reduce the stress of population and to prevent the exposure of workers, especially if an implemented measure is not effective in reducing doses for each particular situation. When an accident with radioactive material causes environmental contamination, decisions about remediation of affected areas are complex because there are many factors associated with decontamination processes. Such complexity is related to technical procedures, public acceptance, the feasibility of implementing the measure, costs and legal aspects. This work is part of a project which aims to develop a multi-criteria tool to provide support for decision making processes in cases of nuclear or radiological accidents in Brazil. Primarily, a database containing information about protective and remediation measures for contaminated areas which can be applied nationally was created. Some criteria have already been defined for the classification of these measures regarding aspects of relevance of pathways to public exposure and of the infrastructure necessary to implement the measure. In this paper, the issues related to the exposure of the workforce are assessed and compared to the dose averted to members of the public resulting from the implementation of each remediation procedure. The procedures described in the database are then ranked according to selected criteria. In the next step, these ratings will be incorporated by the multi-criteria tool. (author)

  16. Definition of criteria related to occupational exposure for use in multi-criteria decision making process for nuclear accidents in Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Diogo N.G.; Guimaraes, Jean R.D., E-mail: dneves@biof.ufrj.br, E-mail: jeanrdg@biof.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Instituto de Biofisica Carlos Chagas Filho; Rochedo, Elaine R.R., E-mail: elainerochedo@gmail.com [Instituto Militar de Engenharia (IME), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Nuclear

    2013-07-01

    After the occurrence of nuclear or radiological accidents, the selection of strategies for remediation of contaminated areas and of protective measures for members of public should be based on previously established criteria. Hence, it becomes possible to reduce the stress of population and to prevent the exposure of workers, especially if an implemented measure is not effective in reducing doses for each particular situation. When an accident with radioactive material causes environmental contamination, decisions about remediation of affected areas are complex because there are many factors associated with decontamination processes. Such complexity is related to technical procedures, public acceptance, the feasibility of implementing the measure, costs and legal aspects. This work is part of a project which aims to develop a multi-criteria tool to provide support for decision making processes in cases of nuclear or radiological accidents in Brazil. Primarily, a database containing information about protective and remediation measures for contaminated areas which can be applied nationally was created. Some criteria have already been defined for the classification of these measures regarding aspects of relevance of pathways to public exposure and of the infrastructure necessary to implement the measure. In this paper, the issues related to the exposure of the workforce are assessed and compared to the dose averted to members of the public resulting from the implementation of each remediation procedure. The procedures described in the database are then ranked according to selected criteria. In the next step, these ratings will be incorporated by the multi-criteria tool. (author)

  17. Preparation of Pb(Zr, Ti)O3 Thin Films on Glass Substrates

    Science.gov (United States)

    Hioki, Tsuyoshi; Akiyama, Masahiko; Ueda, Tomomasa; Onozuka, Yutaka; Hara, Yujiro; Suzuki, Kouji

    2000-09-01

    Lead-zirconate-titanate (PZT) thin films were prepared on non-alkaline glass substrates widely used in liquid crystal display (LCD) devices, by plasma-assisted magnetron RF sputtering with an immersed coil. After preparation of the PZT thin film, the glass was available for use in LCD device processing. No mutual diffusion of the elements was recognized between the glass substrate and the bottom electrode. The PZT layer had a dense film structure with rectangular and columnar grains, and only its perovskite phase was crystalline. PZT thin films on a glass substrate had leakage current densities of about 10-8 A/cm2, acceptable hysteresis loop shapes with the remanent polarization (Pr) of 45 μC/cm2 and the coercive field (Ec) of 90 kV/cm. Ferroelectric properties on a glass substrate almost conform with those on a Si-based substrate.

  18. Geomembrane selection criteria for uranium tailings ponds

    International Nuclear Information System (INIS)

    Mitchell, D.H.; Cuello, R.

    1986-09-01

    The selection criteria, particularly those involving chemical compatibility, of geomembranes to be used in ponds at uranium mill operations are discussed. The principal functional criteria which a geomembrane must meet for this application are: (1) a specified service life and (2) low permeability. Chemical compatibility with the waste is essential in meeting these functional criteria. In two different types of aging tests using simulated acidic uranium mill waste, degradation of chemical and physical properties were examined in geomembranes of high-density polyethylene, polyvinyl chloride, and chlorosulfonated polyethylene. Compatibility tests according to the National Sanitation Foundation procedures are recommended to ascertain the stability of certain physical properties of the proposed geomembrane. Actual experience with a specific geomembrane in an identical application is probably the best method to assure compatibility; however, this experience is frequently not available. Experience with a geomembrane in similar applications is valuable in the selection process, however, small differences in either the geomembrane formulation or the waste composition may result in large differences in performance of the geomembrane. It is likely that many geomembranes have acceptable chemical stability for typical uranium mill applications, therefore, additional factors in the selection processes will include seaming characteristics, mechanical properties, site characteristics, and costs

  19. Indirectly cooled large thin superconducting CDF solenoid

    International Nuclear Information System (INIS)

    Kondo, Kunitaka; Mori, Shigeki; Yoshizaki, Ryozo; Saito, Ryusei; Asano, Katsuhiko.

    1985-01-01

    The manufacturing technique of the indirectly cooled large thin superconducting solenoid for the collider detector facility (CDF solenoid) has been studied through cooperation of University of Tsukuba and the National Laboratory for High Energy Physics of the Ministry of Education of Japan, and the Fermi National Accelerator Laboratory in the U.S. Fabrication and testing of the solenoid has recently been completed by Hitachi. The CDF solenoid has a large-sized thin structure for meeting the requirement by experiments to be applied. Hitachi has thus developed a variety of new technologies including the design standard, coil cooling method, material selection, and manufacturing technique in accordance with experimental data, which were confirmed in a series of analyses and tests made on various prototypes. The CDF solenoid, built using Hitachi's new technologies, is of the world's top class among equipment of this type. This paper outlines the design criteria for the major components employed in the CDF solenoid and the test results of the solenoid. (author)

  20. Final waste forms project: Performance criteria for phase I treatability studies

    International Nuclear Information System (INIS)

    Gilliam, T.M.; Hutchins, D.A.; Chodak, P. III

    1994-06-01

    This document defines the product performance criteria to be used in Phase I of the Final Waste Forms Project. In Phase I, treatability studies will be performed to provide open-quotes proof-of-principleclose quotes data to establish the viability of stabilization/solidification (S/S) technologies. This information is required by March 1995. In Phase II, further treatability studies, some at the pilot scale, will be performed to provide sufficient data to allow treatment alternatives identified in Phase I to be more fully developed and evaluated, as well as to reduce performance uncertainties for those methods chosen to treat a specific waste. Three main factors influence the development and selection of an optimum waste form formulation and hence affect selection of performance criteria. These factors are regulatory, process-specific, and site-specific waste form standards or requirements. Clearly, the optimum waste form formulation will require consideration of performance criteria constraints from each of the three categories. Phase I will focus only on the regulatory criteria. These criteria may be considered the minimum criteria for an acceptable waste form. In other words, a S/S technology is considered viable only if it meet applicable regulatory criteria. The criteria to be utilized in the Phase I treatability studies were primarily taken from Environmental Protection Agency regulations addressed in 40 CFR 260 through 265 and 268; and Nuclear Regulatory Commission regulations addressed in 10 CFR 61. Thus the majority of the identified criteria are independent of waste form matrix composition (i.e., applicable to cement, glass, organic binders etc.)

  1. Imaging and diagnostic criteria for multiple sclerosis: are we there yet?

    International Nuclear Information System (INIS)

    Josey, Lawrence; Curley, Michael; Mousavi, Foroogh Jafari; Taylor, Bruce V.; Lucas, Robyn; Coulthard, Alan

    2012-01-01

    Excluding post traumatic injury, Multiple Sclerosis (MS) is the most common disabling neurological disorder of young adults. Although the effect on mortality is limited, the association of a young demographic and significant morbidity combine to make MS a devastating disease. Since MS was given its first detailed description in 1868, diagnostic criteria continue to evolve. Recently, there has been an international commitment to combine both clinical and paraclinical tests to arrive at an earlier diagnosis. Widespread acceptance of the use of MRI in diagnosis, monitoring and research has made the role of the radiologist more critical than ever in this disease. The primary diagnostic criteria for MS are the International Panel criteria, commonly referred to as the McDonald criteria and it is essential that the radiology community is aware of the work preceding these criteria, so that they are understood in the correct context and the importance acknowledged. Literature review utilising key word search to obtain the historical and current context of magnetic resonance imaging in the diagnosis of MS. A succinct description of the evolution of criteria for the diagnosis of MS. Radiologists must recognise that there are specific diagnostic criteria for MS that continue to evolve as a result of new research, improved technology and clinical experience and it is crucial that these criteria be applied in daily practice. It should be evident that diagnostic imaging criteria for MS will be most effective when combined with standardised MRI protocols such as those published by the international Consortium of Multiple Sclerosis Centres.

  2. Final waste forms project: Performance criteria for phase I treatability studies

    Energy Technology Data Exchange (ETDEWEB)

    Gilliam, T.M. [Oak Ridge National Lab., TN (United States); Hutchins, D.A. [Martin Marietta Energy Systems, Inc., Oak Ridge, TN (United States); Chodak, P. III [Massachusetts Institute of Technology (United States)

    1994-06-01

    This document defines the product performance criteria to be used in Phase I of the Final Waste Forms Project. In Phase I, treatability studies will be performed to provide {open_quotes}proof-of-principle{close_quotes} data to establish the viability of stabilization/solidification (S/S) technologies. This information is required by March 1995. In Phase II, further treatability studies, some at the pilot scale, will be performed to provide sufficient data to allow treatment alternatives identified in Phase I to be more fully developed and evaluated, as well as to reduce performance uncertainties for those methods chosen to treat a specific waste. Three main factors influence the development and selection of an optimum waste form formulation and hence affect selection of performance criteria. These factors are regulatory, process-specific, and site-specific waste form standards or requirements. Clearly, the optimum waste form formulation will require consideration of performance criteria constraints from each of the three categories. Phase I will focus only on the regulatory criteria. These criteria may be considered the minimum criteria for an acceptable waste form. In other words, a S/S technology is considered viable only if it meet applicable regulatory criteria. The criteria to be utilized in the Phase I treatability studies were primarily taken from Environmental Protection Agency regulations addressed in 40 CFR 260 through 265 and 268; and Nuclear Regulatory Commission regulations addressed in 10 CFR 61. Thus the majority of the identified criteria are independent of waste form matrix composition (i.e., applicable to cement, glass, organic binders etc.).

  3. Acceptance and Avoidance Processes at Different Levels of Psychological Recovery from Enduring Mental Illness.

    Science.gov (United States)

    Siqueira, Vinicius R; Oades, Lindsay G

    2015-01-01

    Objective. This study examined the use of psychological acceptance and experiential avoidance, two key concepts of Acceptance and Commitment Therapy (ACT), in the psychological recovery process of people with enduring mental illness. Method. Sixty-seven participants were recruited from the metropolitan, regional, and rural areas of New South Wales, Australia. They all presented some form of chronic mental illness (at least 12 months) as reflected in DSM-IV Axis I diagnostic criteria. The Acceptance and Action Questionnaire (AAQ-19) was used to measure the presence of psychological acceptance and experiential avoidance; the Recovery Assessment Scale (RAS) was used to examine the levels of psychological recovery; and the Scales of Psychological Well-Being was used to observe if there are benefits in utilizing psychological acceptance and experiential avoidance in the recovery process. Results. An analysis of objectively quantifiable measures found no clear correlation between the use of psychological acceptance and recovery in mental illness as measured by the RAS. The data, however, showed a relationship between psychological acceptance and some components of recovery, thereby demonstrating its possible value in the recovery process. Conclusion. The major contribution of this research was the emerging correlation that was observed between psychological acceptance and positive levels of psychological well-being among individuals with mental illness.

  4. Attitudes of belgian students of medicine, philosophy, and law toward euthanasia and the conditions for its acceptance.

    Science.gov (United States)

    Roelands, Marc; Van den Block, Lieve; Geurts, Sylvie; Deliens, Luc; Cohen, Joachim

    2015-01-01

    Euthanasia is legal in Belgium if due care criteria are met, which is judged by committees including physicians, ethicists, and jurists. We examined whether students in these disciplines differ in how they judge euthanasia as an acceptable act. A cross-sectional, anonymous e-mail survey revealed that they have similar attitudes and accept its legalization. Therefore, joint decision-making of physicians, ethicists, and lawyers regarding euthanasia seems to have a common attitudinal base in Belgium. However, they differ to some extent regarding the conditions they put forward for euthanasia being acceptable. Philosophy of life (religion) was an independent predictor of these attitudes.

  5. A generic approach for containment success criteria under severe accident loads

    International Nuclear Information System (INIS)

    Sammataro, R.F.; Solonick, W.R.; Edwards, N.W.

    1992-01-01

    The U.S. Department of Energy (DOE), Office of New Production Reactors (NP), has identified safety as the foremost design criterion for the Heavy Water New Production Reactor (NPR-HWR). The DOE-NP has issued the Deterministic Severe Accident Criteria (DSACs) to guide the design of the NPR-HWR containment for resistance to severe accidents. The DSAC concept provides for a generic approach for success criteria to predict the threshold of containment failure under severe accident loads. This concept consists of two parts: (1) Problem Statements that are qualitative and quantitative bases for calculating associated loadings and containment response to those loadings, and (2) Success Criteria that specify acceptable containment response measures and limits for each problem statement. This paper is limited to a discussion of a generic approach for containment success criteria. The main elements of these success criteria are expressed in terms of elastic stresses and inelastic strains. Containment performance is based on the best estimate of failure as predicted by either stress or strain, buckling, displacements, or ability to withstand missile perforation. Since these limits are best estimates of failure, no conservatism exists in these success criteria. Rather, conservatism is to be provided in the problem statements, i.e., the quantified severe accident loads. These success criteria are presented on a multi-tiered basis for static pressure and temperature loadings, dynamic loadings, and missiles. Within the static pressure and temperature loadings and the dynamic loadings, the criteria are separated into elastic analysis success criteria and inelastic analysis success criteria. Each of these areas, in turn, defines limits on either the stress or strain measures as well as on measures for buckling and displacements

  6. Radiological design criteria for fusion power test facilities

    International Nuclear Information System (INIS)

    Singh, M.S.; Campbell, G.W.

    1982-01-01

    The quest for fusion power and understanding of plasma physics has resulted in planning, design, and construction of several major fusion power test facilities, based largely on magnetic and inertial confinement concepts. We have considered radiological design aspects of the Joint European Torus (JET), Livermore Mirror and Inertial Fusion projects, and Princeton Tokamak. Our analyses on radiological design criteria cover acceptable exposure levels at the site boundary, man-rem doses for plant personnel and population at large, based upon experience gained for the fission reactors, and on considerations of cost-benefit analyses

  7. The effect of discounting, different mortality reduction schemes and predictive cohort life tables on risk acceptability criteria

    International Nuclear Information System (INIS)

    Rackwitz, Ruediger

    2006-01-01

    Technical facilities should be optimal with respect to benefits and cost. Optimization of technical facilities involving risks for human life and limb require an acceptability criterion and suitable discount rates both for the public and the operator depending on for whom the optimization is carried out. The life quality index is presented and embedded into modem socio-economic concepts. A general risk acceptability criterion is derived. The societal life saving cost to be used in optimization as life saving or compensation cost and the societal willingness-to-pay based on the societal value of a statistical life or on the societal life quality index are developed. Different mortality reduction schemes are studied. Also, predictive cohort life tables are derived and applied. Discount rates γ must be long-term averages in view of the time horizon of some 20 to more than 100 years for the facilities of interest and net of inflation and taxes. While the operator may use long-term averages from the financial market for his cost-benefit analysis the assessment of interest rates for investments of the public into risk reduction is more difficult. The classical Ramsey model decomposes the real interest rate (=output growth rate) into the rate of time preference of consumption and the rate of economical growth multiplied by the elasticity of marginal utility of consumption. It is proposed to use a relatively small interest rate of 3% implying a rate of time preference of consumption of about 1%. This appears intergenerationally acceptable from an ethical point of view. Risk-consequence curves are derived for an example

  8. Consideration of Criteria for a Conceptual Near Surface Radioactive Waste disposal Facility in Kenya

    Energy Technology Data Exchange (ETDEWEB)

    Nderitu, Stanley Werugia; Kim, Changlak [KEPCO International Nuclear Graduate School, Ulsan (Korea, Republic of)

    2014-05-15

    The purpose of the criteria is to limit the consequences of events which could lead to radiation exposures. This study will present an approach for establishing radiological waste acceptance criteria using a safety assessment methodology and illustrate some of its application in establishing limits on the total activity and the activity concentrations of radioactive waste to be disposed in a conceptual near surface disposal facility in Kenya. The approach will make use of accepted methods and computational schemes currently used in assessing the safety of near surface disposal facilities. The study will mainly focus on post-closure periods. The study will employ some specific inadvertent human intrusion scenarios in the development of example concentration ranges for the disposal of near-surface wastes. The overall goal of the example calculations is to illustrate the application of the scenarios in a performance assessment to assure that people in the future cannot receive a dose greater than an established limit. The specific performance assessments will use modified scenarios and data to establish acceptable disposal concentrations for specific disposal sites and conditions. Safety and environmental impacts assessments is required in the post-closure phase to support particular decisions in development, operation, and closure of a near surface repository.

  9. Proposed limiting values for performance criteria in acceptance testing of diagnostic X-ray equipment in the Federal Republic of Germany

    International Nuclear Information System (INIS)

    Baeuml, A.

    1989-01-01

    In the Federal Republic of Germany a new X-ray ordinance came into force in 1988 containing a specific paragraph on quality assurance for all medical X-ray units stipulating acceptance tests, regular checks and supervision by medical bodies and the competent authorities. Acceptance testing is to be performed by engineers from equipment suppliers of manufacturers in new and existing installations. It is expected that the service engineers will adjust the equipment in such a way as to obtain optimal performance before measurements are made, the results of which are to be stated in a certificate describing quality status of the equipment. A working group has developed guidelines for these acceptance tests. Items to be measured are reported and proposed limiting values and their tolerances are discussed. (author)

  10. Proposed limiting values for performance criteria in acceptance testing of diagnostic X-ray equipment in the Federal Republic of Germany

    International Nuclear Information System (INIS)

    Baeuml, A.

    1989-01-01

    In the Federal Republic of Germany a new X-ray ordinance came into force in 1988 containing a specific paragraph on quality assurance for all medical X-ray units stipulating acceptance tests, regular checks and supervision by medical bodies and the competent authorities. Acceptance testing is to be performed by engineers from the equipment suppliers or manufacturers in new and also existing installations. It is expected that the service engineers will adjust the equipment in such a way as to obtain optimal performance before measurements are made, the results of which are to be stated in a certificate describing the quality status of the equipment. A working group has developed guidelines for these acceptance tests. The items to be measured are reported and the proposed limiting values and their tolerances are discussed. (author)

  11. Creating a common Danish list of railway timetable evaluation criteria and revising the timetabling process accordingly

    DEFF Research Database (Denmark)

    Schittenhelm, Bernd; Landex, Alex

    2012-01-01

    criteria: capacity consumption on line sections and systematic timetable. Rank 2 criteria: robustness of the timetable and societal acceptance of the timetable and rank 3 criteria: travel time of trains and attractive transfer options. With this new tool a revised timetabling process at Rail Net Denmark...... is proposed. The very basic structure of the process cannot be changed due to EU legislation and Rail Net Europe guidelines. Key performance indicators derived from the identified timetabling criteria are introduced. As is a more iterative approach to the timetabling process due to the assumption of major...... improvements within timetable planning systems. This new iterative timetabling process using key performance indicators will result in improved future timetables and in lower levels of disagreement between timetable stakeholders....

  12. Thinness in young schoolchildren in Serbia: another case of the double burden of malnutrition?

    Science.gov (United States)

    Djordjic, Visnja; Jorga, Jagoda; Radisavljevic, Snezana; Milanovic, Ivana; Bozic, Predrag; Ostojic, Sergej M

    2018-04-01

    Thinness is rarely highlighted or regularly monitored among children in developed countries although it may be rather frequent and pose a significant risk to children's health. We aimed to describe the prevalence of mild, moderate and severe thinness among young Serbian schoolchildren. Cross-sectional study of schoolchildren aged 6-9 years. Children were assessed for weight, height and BMI as part of the WHO European Childhood Obesity Surveillance Initiative in Serbia. Thinness grades were defined as gender- and age-specific cut-offs for BMI according to the International Obesity Task Force criteria. Serbia, September to November 2015. Students (n 4861) in grades 2 and 3 (6-9 years, 2397 girls). Overall prevalence of thinness in Serbian schoolchildren was 9·6 %. Mild thinness was clearly the largest category with a prevalence of 7·6 %, moderate thinness was present in 1·7 % of children and severe thinness was found in 0·3 % of children. OR indicated a significant risk of being thin for girls (1·44 times higher compared with boys) and children attending schools with no health-focused educational programme (1·57 times more likely to be thin than peers enrolled in schools with such programmes). In addition, OR for thinness tended to be 1·23 times higher in children living in an economically disadvantaged region of Serbia (P=0·06). A rather high prevalence of thinness highlights this malnutrition disorder as an emerging health issue that should trigger public health policies to tackle thinness, especially in girls of young age and children living in economically disadvantaged areas.

  13. Tunable thin-film optical filters for hyperspectral microscopy

    Science.gov (United States)

    Favreau, Peter F.; Rich, Thomas C.; Prabhat, Prashant; Leavesley, Silas J.

    2013-02-01

    Hyperspectral imaging was originally developed for use in remote sensing applications. More recently, it has been applied to biological imaging systems, such as fluorescence microscopes. The ability to distinguish molecules based on spectral differences has been especially advantageous for identifying fluorophores in highly autofluorescent tissues. A key component of hyperspectral imaging systems is wavelength filtering. Each filtering technology used for hyperspectral imaging has corresponding advantages and disadvantages. Recently, a new optical filtering technology has been developed that uses multi-layered thin-film optical filters that can be rotated, with respect to incident light, to control the center wavelength of the pass-band. Compared to the majority of tunable filter technologies, these filters have superior optical performance including greater than 90% transmission, steep spectral edges and high out-of-band blocking. Hence, tunable thin-film optical filters present optical characteristics that may make them well-suited for many biological spectral imaging applications. An array of tunable thin-film filters was implemented on an inverted fluorescence microscope (TE 2000, Nikon Instruments) to cover the full visible wavelength range. Images of a previously published model, GFP-expressing endothelial cells in the lung, were acquired using a charge-coupled device camera (Rolera EM-C2, Q-Imaging). This model sample presents fluorescently-labeled cells in a highly autofluorescent environment. Linear unmixing of hyperspectral images indicates that thin-film tunable filters provide equivalent spectral discrimination to our previous acousto-optic tunable filter-based approach, with increased signal-to-noise characteristics. Hence, tunable multi-layered thin film optical filters may provide greatly improved spectral filtering characteristics and therefore enable wider acceptance of hyperspectral widefield microscopy.

  14. Acceptance test report, 241-SY-101 Flexible Receiver System, Phase 1 testing

    International Nuclear Information System (INIS)

    Ritter, G.A.

    1995-01-01

    This document summarizes the results of the Phase 1 acceptance test of the 241-SY-101 Flexible Receiver System (FRS). This acceptance test consisted of a pressure-decay/leak test of the containment bag to verify that the seams along the length of the bag had been adequately sealed. The sealing integrity of the FRS must be verified to ensure that the release of waste and aerosols will be minimized during the removal of the test mixer pump from Tank 241-SY-101. The FRS is one of six major components of the Equipment Removal System, which has been designed to retrieve, transport, and store the mixer pump. This acceptance test was performed at Lancs Industries in Kirkland, Washington on January 17, 1995. The bag temperature-compensated pressure loss of 575 Pa was below the acceptance criteria of 625 Pa and the test results were therefore found to be acceptable. The bag manufacturer estimates that 80--90% of the pressure loss is attributed to leakage around the bag inflation valve where the pressure gage was connected. A leak detector was applied over the entire bag during the pre-tests and no leakage was found. Furthermore, the leak rate corresponding to this pressure loss is very small when compared to the acceptable leak rate of the completely assembled FRS. The sealing integrity of the assembled FRS is verified in Phase 3 testing

  15. UO3 deactivation end point criteria

    International Nuclear Information System (INIS)

    Stefanski, L.D.

    1994-01-01

    The UO 3 Deactivation End Point Criteria are necessary to facilitate the transfer of the UO 3 Facility from the Office of Facility Transition and Management (EM-60) to the office of Environmental Restoration (EM-40). The criteria were derived from a logical process for determining end points for the systems and spaces at the UO 3 , Facility based on the objectives, tasks, and expected future uses pertinent to that system or space. Furthermore, the established criteria meets the intent and supports the draft guidance for acceptance criteria prepared by EM-40, open-quotes U.S. Department of Energy office of Environmental Restoration (EM-40) Decontamination and Decommissioning Guidance Document (Draft).close quotes For the UO 3 Facility, the overall objective of deactivation is to achieve a safe, stable and environmentally sound condition, suitable for an extended period, as quickly and economically as possible. Once deactivated, the facility is kept in its stable condition by means of a methodical surveillance and maintenance (S ampersand M) program, pending ultimate decontamination and decommissioning (D ampersand D). Deactivation work involves a range of tasks, such as removal of hazardous material, elimination or shielding of radiation fields, partial decontamination to permit access for inspection, installation of monitors and alarms, etc. it is important that the end point of each of these tasks be established clearly and in advance, for the following reasons: (1) End points must be such that the central element of the deactivation objective - to achieve stability - is unquestionably achieved. (2) Much of the deactivation work involves worker exposure to radiation or dangerous materials. This can be minimized by avoiding unnecessary work. (3) Each task is, in effect, competing for resources with other deactivation tasks and other facilities. By assuring that each task is appropriately bounded, DOE's overall resources can be used most fully and effectively

  16. Criteria for high-level waste disposal

    International Nuclear Information System (INIS)

    Sousselier, Y.

    1981-01-01

    Disposal of radioactive wastes is storage without the intention of retrieval. But in such storage, it may be useful and in some cases necessary to have the possibility of retrieval at least for a certain period of time. In order to propose some criteria for HLW disposal, one has to examine how this basic concept is to be applied. HLW is waste separated as a raffinate in the first cycle of solvent extraction in reprocessing. Such waste contains the bulk of fission products which have long half lives, therefore the safety of a disposal site, at least after a certain period of time, must be intrinsic, i.e. not based on human intervention. There is a consensus that such a disposal is feasible in a suitable geological formation in which the integrity of the container will be reinforced by several additional barriers. Criteria for disposal can be proposed for all aspects of the question. The author discusses the aims of the safety analysis, particularly the length of time for this analysis, and the acceptable dose commitments resulting from the release of radionuclides, the number and role of each barrier, and a holistic analysis of safety external factors. (Auth.)

  17. Decision modeling and acceptance criteria

    DEFF Research Database (Denmark)

    Ditlevsen, Ove Dalager

    2003-01-01

    compensation value of a human life and a public money equivalent of a human life, where the last value usually is considerably larger than the first value, it is possible from the decision analysis to determine an upper limit that the public should impose on the ratio of the owner´s expected loss rate......) that combines wealth in terms of Gross Domestic Product per person, life expectancy at birth, and yearly work time into a single number. The philosophy behind the published evaluations is that the prevention of a loss of a life is counteracted by a cost such that the LQI remains unchanged (Skjong R, Ronold K......; Decision Analysis; Life quality index; Random interest rate; Risk aversion; Socio-economic value; Uncertainty aversion...

  18. Bayesian risk-based acceptance criteria

    International Nuclear Information System (INIS)

    Martz, H.F.; Abramson, L.R.; Johnson, J.W.

    1996-04-01

    Mechanistic (or deterministic) analysis is traditionally performed in the process of designing a new nuclear reactor or reactor core and also as part of the safety analysis of existing reactors or reload cores. Mechanistic accident analysis is characterized by the specification of an initial operating condition, an initiating event, and subsequent system faults. These subsequent faults are often chosen, through such mechanisms as the worst single failure criterion, so as to maximize the consequences of the accident. Thus, the behavior of all reactor system hardware is prescribed before this analysis begins. Mechanistic analysis then attempts to predict the dynamic response of the system and usually involves detailed reactor physics and thermal-hydraulic predictions of the system behavior, including such parameters as power distributions in the reactor core, coolant temperatures and flow rates, and fuel clad temperature distributions. The objective of this analysis has typically been to establish and verify reactor operating limits and technical specifications, so that severe core damage (SCD) is prevented for a wide variety of reactor accidents

  19. Bridging the Gap between Social Acceptance and Ethical Acceptability.

    Science.gov (United States)

    Taebi, Behnam

    2017-10-01

    New technology brings great benefits, but it can also create new and significant risks. When evaluating those risks in policymaking, there is a tendency to focus on social acceptance. By solely focusing on social acceptance, we could, however, overlook important ethical aspects of technological risk, particularly when we evaluate technologies with transnational and intergenerational risks. I argue that good governance of risky technology requires analyzing both social acceptance and ethical acceptability. Conceptually, these two notions are mostly complementary. Social acceptance studies are not capable of sufficiently capturing all the morally relevant features of risky technologies; ethical analyses do not typically include stakeholders' opinions, and they therefore lack the relevant empirical input for a thorough ethical evaluation. Only when carried out in conjunction are these two types of analysis relevant to national and international governance of risky technology. I discuss the Rawlsian wide reflective equilibrium as a method for marrying social acceptance and ethical acceptability. Although the rationale of my argument is broadly applicable, I will examine the case of multinational nuclear waste repositories in particular. This example will show how ethical issues may be overlooked if we focus only on social acceptance, and will provide a test case for demonstrating how the wide reflective equilibrium can help to bridge the proverbial acceptance-acceptability gap. © 2016 The Authors Risk Analysis published by Wiley Periodicals, Inc. on behalf of Society for Risk Analysis.

  20. A generic approach for steel containment vessel success criteria for severe accident loads

    International Nuclear Information System (INIS)

    Sammataro, R.F.; Solonick, W.R.; Edwards, N.W.

    1993-01-01

    Safety has been defined as the foremost design criterion for the Heavy Water New Production Reactor (NPR-HWR) by the U.S. DOE, Office of New Production Reactors (NP). The DOE-NP issued the Deterministic Severe Accident Criteria (DSAC) concept to guide the design of the NPR-HWR containment for resistance to severe accidents. The DSAC concept provides for a generic approach for containment vessel success criteria to predict the threshold of containment failure under severe accident loads. This concept consists of two parts: (1) Problem Statements and (2) Success Criteria. The paper is limited to a discussion of a success criteria. These criteria define acceptable containment response measures and limits for each problem statement. The criteria are based on the 'best estimate' of failure with no conservatism. Rather, conservatism, if required, is to be provided in the problem statements prepared by the designer and/or the regulatory authorities. The success criteria are presented on a multi-tiered basis for static pressure and temperature loadings, dynamic loadings, and missiles that may impact the containment. Within the static pressure and temperature loadings and the dynamic loadings, the criteria are separated into elastic analysis success criteria and inelastic analysis success criteria. Each of these areas, in turn, defines limits on either the stress or strain measures as well as on measures for buckling and displacements. The rationale upon which these criteria are based is contained in referenced documents. Rigorous validation of the criteria by comparison with results from analytical or experimental programs and application of the criteria to a containment design remain as future tasks. (orig./HP)

  1. Design criteria for XeF2 enabled deterministic transformation of bulk silicon (100) into flexible silicon layer

    KAUST Repository

    Hussain, Aftab M.

    2016-07-15

    Isotropic etching of bulk silicon (100) using Xenon Difluoride (XeF2) gas presents a unique opportunity to undercut and release ultra-thin flexible silicon layers with pre-fabricated state-of-the-art Complementary Metal Oxide Semiconductor (CMOS) electronics. In this work, we present design criteria and mechanism with a comprehensive mathematical model for this method. We consider various trench geometries and parametrize important metrics such as etch time, number of cycles and area efficiency in terms of the trench diameter and spacing so that optimization can be done for specific applications. From our theoretical analysis, we conclude that a honeycomb-inspired hexagonal distribution of trenches can produce the most efficient release of ultra-thin flexible silicon layers in terms of the number of etch cycles, while a rectangular distribution of circular trenches provides the most area efficient design. The theoretical results are verified by fabricating and releasing (varying sizes) flexible silicon layers. We observe uniform translation of design criteria into practice for etch distances and number of etch cycles, using reaction efficiency as a fitting parameter.

  2. Design criteria for XeF2 enabled deterministic transformation of bulk silicon (100) into flexible silicon layer

    KAUST Repository

    Hussain, Aftab M.; Shaikh, Sohail F.; Hussain, Muhammad Mustafa

    2016-01-01

    Isotropic etching of bulk silicon (100) using Xenon Difluoride (XeF2) gas presents a unique opportunity to undercut and release ultra-thin flexible silicon layers with pre-fabricated state-of-the-art Complementary Metal Oxide Semiconductor (CMOS) electronics. In this work, we present design criteria and mechanism with a comprehensive mathematical model for this method. We consider various trench geometries and parametrize important metrics such as etch time, number of cycles and area efficiency in terms of the trench diameter and spacing so that optimization can be done for specific applications. From our theoretical analysis, we conclude that a honeycomb-inspired hexagonal distribution of trenches can produce the most efficient release of ultra-thin flexible silicon layers in terms of the number of etch cycles, while a rectangular distribution of circular trenches provides the most area efficient design. The theoretical results are verified by fabricating and releasing (varying sizes) flexible silicon layers. We observe uniform translation of design criteria into practice for etch distances and number of etch cycles, using reaction efficiency as a fitting parameter.

  3. Decommissioning of nuclear facilities using current criteria

    International Nuclear Information System (INIS)

    Shum, E.Y.; Swift, J.J.; Malaro, J.C.

    1991-01-01

    When a licensed nuclear facility ceases operation, the US Nuclear Regulatory Commission (NRC) is responsible for ensuring that the facility and its site are decontaminated to an acceptable level so that it is safe to release that facility and site for unrestricted public use. Currently, the NRC is developing decommissioning criteria based on reducing public doses from residual contamination in soils and structures at sites released for unrestricted use to as low as is reasonably achievable (ALARA). Plans are to quantify ALARA in terms of an annual total effective dose equivalent (TEDE) to an average member of the most highly exposed population group. The NRC is working on a regulatory guidance document to provide a technical basis for translating residual contamination levels to annual dose levels. Another regulatory guide is being developed to provide guidance to the licensee on how to conduct radiological surveys to demonstration compliance with the NRC decommissioning criteria. The methods and approaches used in these regulatory guides on the decommissioning of a nuclear facility are discussed in the paper

  4. Microbiological criteria for good manufacturing practice (GMP)

    Energy Technology Data Exchange (ETDEWEB)

    Farkas, J. (Inst. of Preservation and Livestock Products Technology, Univ. of Horticulture and Food Industry, Budapest (Hungary)); Zukal, E. (Inst. of Preservation and Livestock Products Technology, Univ. of Horticulture and Food Industry, Budapest (Hungary))

    1992-01-01

    Good manufacturing practice (GMP) consist of an effective manufacturing operation and an effective application of food control. GMP is best supported by the Hazard Analysis Critical Control Point system (HACCP) of the preventive quality assurance, which requires that food irradiation as any food processing technology should be used only with foods of an acceptable quality and adequate handling and storage procedures should precede and follow the processing. The paper concentrates on the first element of the HACCP system for an irradiation plant: the incoming product control, i.e. whether GMP of foods to be irradiated can be assessed by establishing microbiological criteria for their previous good manufacturing practice. In this regard, it summarizes considerations and findings of a ''Consultation on Microbiological Criteria for Foods to be Further Processed Including by Irradiation'' held in 1989 by the International Consultative Group on Food irradiation at the Headquarters of the World Health Organization, Geneva. Difficulties in establishing reference values and defining good manufacturing practices will be pointed out. (orig.)

  5. Toward optimizing patient-specific IMRT QA techniques in the accurate detection of dosimetrically acceptable and unacceptable patient plans.

    Science.gov (United States)

    McKenzie, Elizabeth M; Balter, Peter A; Stingo, Francesco C; Jones, Jimmy; Followill, David S; Kry, Stephen F

    2014-12-01

    The authors investigated the performance of several patient-specific intensity-modulated radiation therapy (IMRT) quality assurance (QA) dosimeters in terms of their ability to correctly identify dosimetrically acceptable and unacceptable IMRT patient plans, as determined by an in-house-designed multiple ion chamber phantom used as the gold standard. A further goal was to examine optimal threshold criteria that were consistent and based on the same criteria among the various dosimeters. The authors used receiver operating characteristic (ROC) curves to determine the sensitivity and specificity of (1) a 2D diode array undergoing anterior irradiation with field-by-field evaluation, (2) a 2D diode array undergoing anterior irradiation with composite evaluation, (3) a 2D diode array using planned irradiation angles with composite evaluation, (4) a helical diode array, (5) radiographic film, and (6) an ion chamber. This was done with a variety of evaluation criteria for a set of 15 dosimetrically unacceptable and 9 acceptable clinical IMRT patient plans, where acceptability was defined on the basis of multiple ion chamber measurements using independent ion chambers and a phantom. The area under the curve (AUC) on the ROC curves was used to compare dosimeter performance across all thresholds. Optimal threshold values were obtained from the ROC curves while incorporating considerations for cost and prevalence of unacceptable plans. Using common clinical acceptance thresholds, most devices performed very poorly in terms of identifying unacceptable plans. Grouping the detector performance based on AUC showed two significantly different groups. The ion chamber, radiographic film, helical diode array, and anterior-delivered composite 2D diode array were in the better-performing group, whereas the anterior-delivered field-by-field and planned gantry angle delivery using the 2D diode array performed less well. Additionally, based on the AUCs, there was no significant difference

  6. [Early diagnosis of HIV in Primary Care in Spain. Results of a pilot study based on targeted screening based on indicator conditions, behavioral criteria and region of origin].

    Science.gov (United States)

    Agustí, Cristina; Martín-Rabadán, María; Zarco, José; Aguado, Cristina; Carrillo, Ricard; Codinachs, Roger; Carmona, Jose Manuel; Casabona, Jordi

    2018-03-01

    To estimate the prevalence of HIV infection in patients diagnosed with an indicator condition (IC) for HIV and/or risk behavior for their acquisition and/or coming from high prevalence countries. To determine the acceptability and feasibility of offering HIV testing based on IC and behavioral and origin criteria in Primary Care (PC). Cross-sectional study in a convenience sample. Six PC centers in Spain. The inclusion criteria were: patients between 16 and 65years old who presented at least one of the proposed ICs and/or at least one of the proposed behavioral and/or origin criteria. A total of 388 patients participated. HIV serology was offered to all patients who met the inclusion criteria. Description of IC frequency, behavioral and origin criteria. Prevalence of HIV infection. Level of acceptability and feasibility of the HIV screening based on IC and behavioral and origin criteria. A total of 174 patients had an IC (44.84%). The most common behavioral criterion was: having unprotected sex at some time in life with people who did not know their HIV status (298; 76.8%). Four HIV+ patients (1.03%) were diagnosed. All had an IC and were men who had sex with men. The level of acceptability in PC was high. Offering HIV testing to patients with IC and behavioral criteria is feasible and effective in PC. Copyright © 2017 Elsevier España, S.L.U. All rights reserved.

  7. Acceptability of HIV self-testing: a systematic literature review.

    Science.gov (United States)

    Krause, Janne; Subklew-Sehume, Friederike; Kenyon, Chris; Colebunders, Robert

    2013-08-08

    The uptake of HIV testing and counselling services remains low in risk groups around the world. Fear of stigmatisation, discrimination and breach of confidentiality results in low service usage among risk groups. HIV self-testing (HST) is a confidential HIV testing option that enables people to find out their status in the privacy of their homes. We evaluated the acceptability of HST and the benefits and challenges linked to the introduction of HST. A literature review was conducted on the acceptability of HST in projects in which HST was offered to study participants. Besides acceptability rates of HST, accuracy rates of self-testing, referral rates of HIV-positive individuals into medical care, disclosure rates and rates of first-time testers were assessed. In addition, the utilisation rate of a telephone hotline for counselling issues and clients` attitudes towards HST were extracted. Eleven studies met the inclusion criteria (HST had been offered effectively to study participants and had been administered by participants themselves) and demonstrated universally high acceptability of HST among study populations. Studies included populations from resource poor settings (Kenya and Malawi) and from high-income countries (USA, Spain and Singapore). The majority of study participants were able to perform HST accurately with no or little support from trained staff. Participants appreciated the confidentiality and privacy but felt that the provision of adequate counselling services was inadequate. The review demonstrates that HST is an acceptable testing alternative for risk groups and can be performed accurately by the majority of self-testers. Clients especially value the privacy and confidentiality of HST. Linkage to counselling as well as to treatment and care services remain major challenges.

  8. The Relationship between Treatment Integrity and Acceptability of Reading Interventions for Children with Attention-Deficit/Hyperactivity Disorder

    Science.gov (United States)

    Mautone, Jennifer A.; DuPaul, George J.; Jitendra, Asha K.; Tresco, Katy E.; Junod, Rosemary Vile; Volpe, Robert J.

    2009-01-01

    This study examined the relationship between treatment integrity and acceptability for reading interventions across two consultation models, intensive data-based academic intervention (IDAI) and traditional data-based academic intervention (TDAI). Participants included 83 first- through fourth-grade students who met research criteria for…

  9. Conference on wind power development in the face of landscape and local project acceptability challenges

    International Nuclear Information System (INIS)

    Victoire Lejzerzon; Sauron, Claire; Villot, Marie; Ratzbor, Guenter; Tausch, Christian; Cagneaux, Bertrand; Jouneau, Agathe; Stemmer, Boris; Huebner, Gundula; Orozco-Souel, Paola; Lhermitte, Charles; Ferus, Elisabeth; Benezech, Philippe; Gunzelmann, Thomas

    2015-01-01

    The French-German office for Renewable energies (OFAEnR) organised a conference on n wind power development in the face of landscape and local project acceptability challenges. In the framework of this French-German exchange of experience, participants addressed the following points: the conciliation between landscape protection and wind power development, the definition of landscape environmental quality criteria, the needs and usages of the departments in charge of the treatment of landscape studies in France, the socio-psychological approach of the local acceptability of wind farm projects, the re-powering tool for the improvement of the wind farm integration in the landscape, and the conciliation between the monuments maintenance and wind power development. This document brings together the available presentations (slides) made during this event: 1 - Conciliating landscape protection and wind power development goals in France (Marie Villot); 2 - Wind turbines: Conflicts between development goals, landscape and acceptance - Perception and criteria (Guenter Ratzbor); 3 - Bayern's wind power atlas: a planning tool which takes into account the landscape aspects (Christian Tausch); 4 - Landscape assessment in wind farms projects: what and how to do in French administrative procedures? (Bertrand Cagneaux); 5 - Methods for evaluation of landscape for wind farms projects - A French project developer's feedback (Agathe Jouneau); 6 - Landscape Assessment: Methods from German Landscape Practice (Boris Stemmer); 7 - Acceptance of Wind Turbines - Social Psychological Research (Gundula Huebner); 8 - Local consultation: who to involve, when and how? (Paola Orozco-Souel); 9 - Local acceptability: what dialogue concepts and strategies, and how to manage wind energy objection (Charles Lhermitte); 10 - Re-powering and landscape: chances and limits (Elisabeth Ferus); 11 - Wind power and cultural heritage: consultation and dialogue to succeed (Philippe Benezech); 12

  10. Power Distribution System Planning Evaluation by a Fuzzy Multi-Criteria Group Decision Support System

    Directory of Open Access Journals (Sweden)

    Tiefeng Zhang

    2010-10-01

    Full Text Available The evaluation of solutions is an important phase in power distribution system planning (PDSP which allows issues such as quality of supply, cost, social service and environmental implications to be considered and usually involves the judgments of a group of experts. The planning problem is thus suitable for the multi-criteria group decision-making (MCGDM method. The evaluation process and evaluation criteria often involve uncertainties incorporated in quantitative analysis with crisp values and qualitative judgments with linguistic terms; therefore, fuzzy sets techniques are applied in this study. This paper proposes a fuzzy multi-criteria group decision-making (FMCGDM method for PDSP evaluation and applies a fuzzy multi-criteria group decision support system (FMCGDSS to support the evaluation task. We introduce a PDSP evaluation model, which has evaluation criteria within three levels, based on the characteristics of a power distribution system. A case-based example is performed on a test distribution network and demonstrates how all the problems in a PDSP evaluation are addressed using FMCGDSS. The results are acceptable to expert evaluators.

  11. Feasibility Study on the Development of Index that Shows Social and Cultural Acceptance of Nuclear Power

    Energy Technology Data Exchange (ETDEWEB)

    Cho, SeongKyung [Bangmok College of General Education at Myongji Univ., Yongin (Korea, Republic of); Choi, Seungho; Yoon, Hana; Song, Jiyeon [Domo Brodeur, Seoul (Korea, Republic of)

    2015-05-15

    In this context, it is necessary to manage and develop an index that can measure the level of public acceptance by establishing the terms of social/cultural public acceptance of nuclear power in a practical manner and by identifying influential factors of public acceptance. Developing an index itself is not intended to increase the public acceptance of nuclear power. This study intends to contribute to determining energy policy acceptable to the public by estimating the level of potential social conflicts related to nuclear power policies with eligible evaluation criteria on social/cultural acceptance and by reducing relevant social costs. Key conclusions and proposal of this research are as follows. First, the influential factors of acceptance are reliability of nuclear safety, risk perception of nuclear power and beneficial perception of nuclear power. Among them, reliability of nuclear safety appears to have the most influence. In addition, benefit perception of nuclear power at the social level is significantly higher than that at the individual level. However, in relation to risk perception, a gap between experts and the public is found as nuclear industry premises that accident does not occur while the public premises that accident may occur.

  12. Feasibility Study on the Development of Index that Shows Social and Cultural Acceptance of Nuclear Power

    International Nuclear Information System (INIS)

    Cho, SeongKyung; Choi, Seungho; Yoon, Hana; Song, Jiyeon

    2015-01-01

    In this context, it is necessary to manage and develop an index that can measure the level of public acceptance by establishing the terms of social/cultural public acceptance of nuclear power in a practical manner and by identifying influential factors of public acceptance. Developing an index itself is not intended to increase the public acceptance of nuclear power. This study intends to contribute to determining energy policy acceptable to the public by estimating the level of potential social conflicts related to nuclear power policies with eligible evaluation criteria on social/cultural acceptance and by reducing relevant social costs. Key conclusions and proposal of this research are as follows. First, the influential factors of acceptance are reliability of nuclear safety, risk perception of nuclear power and beneficial perception of nuclear power. Among them, reliability of nuclear safety appears to have the most influence. In addition, benefit perception of nuclear power at the social level is significantly higher than that at the individual level. However, in relation to risk perception, a gap between experts and the public is found as nuclear industry premises that accident does not occur while the public premises that accident may occur

  13. Phenomenology of the domain walls in thin ferromagnetic films

    International Nuclear Information System (INIS)

    Adam, G.

    1978-01-01

    The basic concepts and the main theoretical methods developed in the study of the domain walls in thin ferromagnetic films are given in this review. First, an insight into the origins and the classification criteria of the conceptually different wall structures is obtained by elementary considerations which are mainly based on the experimentally available data. Then, the more subtle aspect of the wall models dimensionality in soft ferromagnetic films is discussed. Finally, the various theoretical calculation methods of the wall parameters are summarized. (author)

  14. Evaluation criteria for dialogue processes: key findings from RISCOM II

    International Nuclear Information System (INIS)

    Atherton, Elizabeth

    2003-01-01

    As part of Work Package 4 (undertaken by a consortium of partners from the United Kingdom) in the joint European project RISCOM II, work was undertaken on evaluation criteria for determining the success of dialogue processes; this note outlines its key findings as, in order to continue the development of dialogue processes, it is important to evaluate and learn from the experience of engaging with stakeholders. Criteria can be developed to evaluate how successful a process has been, these can range from very practical criteria relating to how well the process worked or be linked to more subjective criteria developed from the aims of the dialogue process itself. Some criteria are particularly relevant to dialogue processes that aim to encourage deliberation and the development of stakeholders' views through participation in the dialogue process: transparency, legitimacy, equality of access, 'being able to speak', a deliberative environment, openness of framing, developing insight into range of issues (new meanings are generated), inclusive and 'best' knowledge elicited, producing acceptable/tolerable and usable outcomes/decisions, improvement of trust and understanding between participants, developing a sense of shared responsibility and common good. Evaluation will incur a cost in terms of time and money, but will help practitioners to be able to develop processes that meet the needs of those who participate and improve the way that we try to engage people in the debate

  15. Discussion on the environmental protection acceptance method and the critical issues of the completion of projects about radiation usage in the hospitals

    International Nuclear Information System (INIS)

    Wang Wei

    2014-01-01

    It is widely used in the world that the hospitals take advantages of radiation technology. Practically it is involved radioactive isotope, sealed source and the usage of ray device. Based on the environmental protection acceptance of the finished projects, this article is aimed at the actual characteristics of the medical practice and differentiating the major factors of environmental effects, choosing the monitoring criteria and method of environmental protection acceptance and exploring the critical issues in the course of acceptance. Finally this essay is intended to provide theory evidence and technical support in the acceptance of the above projects. (author)

  16. Acceptance test report for portable exhauster POR-007/Skid E

    International Nuclear Information System (INIS)

    Kriskovich, J.R.

    1998-01-01

    This document describes Acceptance Testing performed on Portable Exhauster POR-007/Skid E. It includes measurements of bearing vibration levels, pressure decay testing, programmable logic controller interlocks, high vacuum, flow and pressure control functional testing. The purpose of Acceptance testing documented by this report was to demonstrate compliance of the exhausters with the performance criteria established within HNF-0490, Rev. 1 following a repair and upgrade effort at Hanford. In addition, data obtained during this testing is required for the resolution of outstanding Non-conformance Reports (NCR), and finally, to demonstrate the functionality of the associated software for the pressure control and high vacuum exhauster operating modes provided for by W-320. Additional testing not required by the ATP was also performed to assist in the disposition and close out of receiving inspection report and for application design information (system curve). Results of this testing are also captured within this document

  17. Design criteria for XeF{sub 2} enabled deterministic transformation of bulk silicon (100) into flexible silicon layer

    Energy Technology Data Exchange (ETDEWEB)

    Hussain, Aftab M.; Shaikh, Sohail F.; Hussain, Muhammad M., E-mail: muhammadmustafa.hussain@kaust.edu.sa [Integrated Nanotechnology Laboratory (INL) and Integrated Disruptive Electronics Applications (IDEA) Laboratory, Computer Electrical Mathematical Science and Engineering Division, King Abdullah University of Science and Technology - KAUST, Thuwal 23955-6900 (Saudi Arabia)

    2016-07-15

    Isotropic etching of bulk silicon (100) using Xenon Difluoride (XeF{sub 2}) gas presents a unique opportunity to undercut and release ultra-thin flexible silicon layers with pre-fabricated state-of-the-art Complementary Metal Oxide Semiconductor (CMOS) electronics. In this work, we present design criteria and mechanism with a comprehensive mathematical model for this method. We consider various trench geometries and parametrize important metrics such as etch time, number of cycles and area efficiency in terms of the trench diameter and spacing so that optimization can be done for specific applications. From our theoretical analysis, we conclude that a honeycomb-inspired hexagonal distribution of trenches can produce the most efficient release of ultra-thin flexible silicon layers in terms of the number of etch cycles, while a rectangular distribution of circular trenches provides the most area efficient design. The theoretical results are verified by fabricating and releasing (varying sizes) flexible silicon layers. We observe uniform translation of design criteria into practice for etch distances and number of etch cycles, using reaction efficiency as a fitting parameter.

  18. Five criteria for using a surrogate endpoint to predict treatment effect based on data from multiple previous trials.

    Science.gov (United States)

    Baker, Stuart G

    2018-02-20

    A surrogate endpoint in a randomized clinical trial is an endpoint that occurs after randomization and before the true, clinically meaningful, endpoint that yields conclusions about the effect of treatment on true endpoint. A surrogate endpoint can accelerate the evaluation of new treatments but at the risk of misleading conclusions. Therefore, criteria are needed for deciding whether to use a surrogate endpoint in a new trial. For the meta-analytic setting of multiple previous trials, each with the same pair of surrogate and true endpoints, this article formulates 5 criteria for using a surrogate endpoint in a new trial to predict the effect of treatment on the true endpoint in the new trial. The first 2 criteria, which are easily computed from a zero-intercept linear random effects model, involve statistical considerations: an acceptable sample size multiplier and an acceptable prediction separation score. The remaining 3 criteria involve clinical and biological considerations: similarity of biological mechanisms of treatments between the new trial and previous trials, similarity of secondary treatments following the surrogate endpoint between the new trial and previous trials, and a negligible risk of harmful side effects arising after the observation of the surrogate endpoint in the new trial. These 5 criteria constitute an appropriately high bar for using a surrogate endpoint to make a definitive treatment recommendation. Published 2017. This article is a U.S. Government work and is in the public domain in the USA.

  19. Reliability Criteria for Thick Bonding Wire.

    Science.gov (United States)

    Dagdelen, Turker; Abdel-Rahman, Eihab; Yavuz, Mustafa

    2018-04-17

    Bonding wire is one of the main interconnection techniques. Thick bonding wire is widely used in power modules and other high power applications. This study examined the case for extending the use of traditional thin wire reliability criteria, namely wire flexure and aspect ratio, to thick wires. Eleven aluminum (Al) and aluminum coated copper (CucorAl) wire samples with diameter 300 μm were tested experimentally. The wire response was measured using a novel non-contact method. High fidelity FEM models of the wire were developed and validated. We found that wire flexure is not correlated to its stress state or fatigue life. On the other hand, aspect ratio is a consistent criterion of thick wire fatigue life. Increasing the wire aspect ratio lowers its critical stress and increases its fatigue life. Moreover, we found that CucorAl wire has superior performance and longer fatigue life than Al wire.

  20. Reliability Criteria for Thick Bonding Wire

    Science.gov (United States)

    Yavuz, Mustafa

    2018-01-01

    Bonding wire is one of the main interconnection techniques. Thick bonding wire is widely used in power modules and other high power applications. This study examined the case for extending the use of traditional thin wire reliability criteria, namely wire flexure and aspect ratio, to thick wires. Eleven aluminum (Al) and aluminum coated copper (CucorAl) wire samples with diameter 300 μm were tested experimentally. The wire response was measured using a novel non-contact method. High fidelity FEM models of the wire were developed and validated. We found that wire flexure is not correlated to its stress state or fatigue life. On the other hand, aspect ratio is a consistent criterion of thick wire fatigue life. Increasing the wire aspect ratio lowers its critical stress and increases its fatigue life. Moreover, we found that CucorAl wire has superior performance and longer fatigue life than Al wire. PMID:29673194

  1. Quality assurance requirements and methods for high level waste package acceptability

    International Nuclear Information System (INIS)

    1992-12-01

    This document should serve as guidance for assigning the necessary items to control the conditioning process in such a way that waste packages are produced in compliance with the waste acceptance requirements. It is also provided to promote the exchange of information on quality assurance requirements and on the application of quality assurance methods associated with the production of high level waste packages, to ensure that these waste packages comply with the requirements for transportation, interim storage and waste disposal in deep geological formations. The document is intended to assist both the operators of conditioning facilities and repositories as well as national authorities and regulatory bodies, involved in the licensing of the conditioning of high level radioactive wastes or in the development of deep underground disposal systems. The document recommends the quality assurance requirements and methods which are necessary to generate data for these parameters identified in IAEA-TECDOC-560 on qualitative acceptance criteria, and indicates where and when the control methods can be applied, e.g. in the operation or commissioning of a process or in the development of a waste package design. Emphasis is on the control of the process and little reliance is placed on non-destructive or destructive testing. Qualitative criteria, relevant to disposal of high level waste, are repository dependent and are not addressed here. 37 refs, 3 figs, 2 tabs

  2. Radiological control criteria for materials considered for recycle and reuse

    International Nuclear Information System (INIS)

    Kennedy, W.E. Jr.; Hill, R.L.; Aaberg, R.L.; Wallo, A. III

    1994-11-01

    Pacific Northwest Laboratory (PNL) is conducting technical analyses to support the US Department of Energy (DOE), Office of Environmental Guidance, Air, Water, and Radiation Division (DOE/EH-232) in developing radiological control criteria for recycling or reuse of metals or equipment containing residual radioactive contamination from DOE operations. The criteria, framed as acceptable concentrations for release of materials for recycling or reuse, are risk-based and were developed through analysis of generic radiation exposure scenarios and pathways. The analysis includes evaluation of relevant radionuclides, potential mechanisms of exposure, and non-health-related impacts of residual radioactivity on electronics and film. The analysis considers 42 key radionuclides that DOE operations are known to generate and that may be contained in recycled or reused metals or equipment. Preliminary results are compared with similar results reported by the International Atomic Energy Agency, by radionuclide grouping

  3. Public acceptance of renewable energies. Results from case studies in Germany

    Energy Technology Data Exchange (ETDEWEB)

    Zoellner, Jan; Schweizer-Ries, Petra; Wemheuer, Christin [Department of Psychology, Otto-von-Guericke-University Magdeburg, Universitaetsplatz 2, 39106 Magdeburg (Germany)

    2008-11-15

    This article addresses the public acceptance of certain renewable energies (grid-connected larger PV ground-installed systems, biomass plants and wind turbines) from a socio-scientific perspective. Using an environmental-psychological approach to investigate the social factors relevant to the formation of public acceptance towards renewable energies in four different regions, recommendations for the further implementation of renewable energy systems were to be derived. The present study has been conducted in a multi-modal research design combining a standardised questionnaire and qualitative interviews and focused on the residents' views and perceptions. Especially within the quantitative analyses, the results indicate that economic consideration of the respective renewable energy system, understood as a positive cost-benefit calculation made by the individual, is the strongest predictor for a reported acceptance. Furthermore, the importance of landscape evaluation and a strong connection between procedural justice criteria, such as transparency, early and accurate information as well as possibilities to participate during the planning and installation process, and a reported public acceptance became evident. Qualitative data were analysed in reference to the grounded theory and showed the relevance of the operating company's commitment on the local level, participation of the general public and the choice of the location for the plant were among the relevant aspects for acceptance in the implementation process. This survey is part of a 3-year project funded by the Federal Ministry for the Environment, Nature Conservation and Nuclear Safety (BMU). (author)

  4. Public acceptance of renewable energies: Results from case studies in Germany

    Energy Technology Data Exchange (ETDEWEB)

    Zoellner, Jan [Department of Psychology, Otto-von-Guericke-University Magdeburg, Universitaetsplatz 2, 39106 Magdeburg (Germany)], E-mail: jan.zoellner@ovgu.de; Schweizer-Ries, Petra; Wemheuer, Christin [Department of Psychology, Otto-von-Guericke-University Magdeburg, Universitaetsplatz 2, 39106 Magdeburg (Germany)

    2008-11-15

    This article addresses the public acceptance of certain renewable energies (grid-connected larger PV ground-installed systems, biomass plants and wind turbines) from a socio-scientific perspective. Using an environmental-psychological approach to investigate the social factors relevant to the formation of public acceptance towards renewable energies in four different regions, recommendations for the further implementation of renewable energy systems were to be derived. The present study has been conducted in a multi-modal research design combining a standardised questionnaire and qualitative interviews and focused on the residents' views and perceptions. Especially within the quantitative analyses, the results indicate that economic consideration of the respective renewable energy system, understood as a positive cost-benefit calculation made by the individual, is the strongest predictor for a reported acceptance. Furthermore, the importance of landscape evaluation and a strong connection between procedural justice criteria, such as transparency, early and accurate information as well as possibilities to participate during the planning and installation process, and a reported public acceptance became evident. Qualitative data were analysed in reference to the grounded theory and showed the relevance of the operating company's commitment on the local level, participation of the general public and the choice of the location for the plant were among the relevant aspects for acceptance in the implementation process. This survey is part of a 3-year project funded by the Federal Ministry for the Environment, Nature Conservation and Nuclear Safety (BMU)

  5. Public acceptance of renewable energies: Results from case studies in Germany

    International Nuclear Information System (INIS)

    Zoellner, Jan; Schweizer-Ries, Petra; Wemheuer, Christin

    2008-01-01

    This article addresses the public acceptance of certain renewable energies (grid-connected larger PV ground-installed systems, biomass plants and wind turbines) from a socio-scientific perspective. Using an environmental-psychological approach to investigate the social factors relevant to the formation of public acceptance towards renewable energies in four different regions, recommendations for the further implementation of renewable energy systems were to be derived. The present study has been conducted in a multi-modal research design combining a standardised questionnaire and qualitative interviews and focused on the residents' views and perceptions. Especially within the quantitative analyses, the results indicate that economic consideration of the respective renewable energy system, understood as a positive cost-benefit calculation made by the individual, is the strongest predictor for a reported acceptance. Furthermore, the importance of landscape evaluation and a strong connection between procedural justice criteria, such as transparency, early and accurate information as well as possibilities to participate during the planning and installation process, and a reported public acceptance became evident. Qualitative data were analysed in reference to the grounded theory and showed the relevance of the operating company's commitment on the local level, participation of the general public and the choice of the location for the plant were among the relevant aspects for acceptance in the implementation process. This survey is part of a 3-year project funded by the Federal Ministry for the Environment, Nature Conservation and Nuclear Safety (BMU)

  6. A Preliminary Investigation of Acceptance and Commitment Therapy as a Treatment for Marijuana Dependence in Adults

    Science.gov (United States)

    Twohig, Michael P.; Shoenberger, Deacon; Hayes, Steven C.

    2007-01-01

    In this investigation, 3 adults who met criteria for marijuana dependence were treated using an abbreviated version of acceptance and commitment therapy (ACT). The treatment was delivered in eight weekly 90-min individual sessions. The effects of the intervention were assessed using a nonconcurrent multiple baseline across participants design.…

  7. Vacuum Pumping Performance Comparison of Non-Evaporable Getter Thin Films Deposited Using Argon and Krypton as Sputtering Gases

    CERN Document Server

    Liu, Xianghong; He, Yun; Li, Yulin

    2005-01-01

    Owing to the outstanding vacuum performance and the low secondary electron yield, non-evaporable getter (NEG) thin film deposited onto interior walls has gained widespread acceptance and has been incorporated into many accelerator vacuum system designs. The titanium-zirconium-vanadium (T-Zr-V) NEG thin films were deposited onto the interior wall of stainless steel pipes via DC magnetron sputtering method using either argon or krypton gas as sputtering gas. Vacuum pumping evaluation tests were carried out to compare vacuum pumping performances of the Ti-Zr-V NEG thin films deposited using argon or krypton. The results showed much higher initial pumping speed for the Kr-sputtered NEG film than the Ar-sputtered film, though both films have similar activation behavior. The compositions and textures of both thin films were measured to correlate to the pumping performances.

  8. The leak before break criteria, requirements and implications; El criterio de fuga antes de ruptura, requerimientos e implicaciones

    Energy Technology Data Exchange (ETDEWEB)

    Martinez M, E

    1992-05-15

    Inside this work a general balance is made on the Leak before break approach (LBB), like they are the history and licensing, those limitations, the acceptance criteria of the LBB, the current state of the regulatory development and the current state of it application in countries like E.U.A, Germany, Canada, Italy and France. Everything it with the purpose of evaluating the opportunities that offers the LBB criteria for it possible application in Mexico. (Author)

  9. Preparing to Accept Research Data: Creating Guidelines for Librarians

    Directory of Open Access Journals (Sweden)

    Laura B. Palumbo

    2015-11-01

    Full Text Available Rutgers University Libraries have recognized the need to expand their current research data services into a well-documented and well-supported service available to the Rutgers research community. In 2005, Rutgers University Libraries created RUcore, Rutgers University Community Repository, which has served as the University’s formal repository for institutional scholarship, special collections, and Electronic Theses & Dissertations. With the impetus of the 2010 NSF directive for research data sharing and preservation, RUcore development was extended to accept research data content. Ingest of pilot data projects began in 2010 via a librarian-mediated process. In order to provide a better defined workflow and mission for research data services, in July 2014, the Rutgers University Librarian organized a Task Force to investigate the evaluation process for technical, legal, and confidential issues involved in research data acceptance, and to establish an administrative and evaluation framework for the deposit of research data. After a review of 35 repositories using 34 criteria, the Task Force drafted a plan for research data acceptance which proposes wide-spread acceptance of mediated data projects, and prepares for future self-deposit in an online interface. This paper will discuss the issues addressed by the Task Force; acknowledging ownership of data through an institutional data policy, preventing exposure of confidential or sensitive data, establishing a reconfigured data team, requirements for storage capacity and funding, creating a workflow which includes collaboration with research offices, and offering guidance for both researchers and librarians working with research data.

  10. Fabrication and Characterisation of Flexible Coaxial Thin Thread Supercapacitors

    Directory of Open Access Journals (Sweden)

    Fulian Qiu

    2014-08-01

    Full Text Available Flexible coaxial thin thread supercapacitors were fabricated semi-automatically using a dip coating method. A typical coaxial thin thread supercapacitor of a length of 70 cm demonstrated a specific length capacitance of 0.3 mF cm-1 (11.2 mF cm-2 and 2.18 F cm-3 at 5 mV s-1, the device exhibited good electrochemical performance with a high volume energy density of 0.22 mWh cm-3 at a power density of 22 mW cm-3. Thread supercapacitors were assembled in series and parallel combinations, the accepted models for series and parallel circuit combinations were obeyed for two coaxial thread supercapacitors. The thread shows high flexibility and uniformity of specific length capacitance, one integrated with a commercial solar cell could be charged and power a LED. The process is simple, robust and easy to scale up to make unlimited length thread supercapacitors for numerous miniaturized and flexible electronic applications.

  11. Present state of the design and realization of regional radioactive waste depositories and waste acceptance criteria for disposal. Soucasny stav reseni a realizace regionalnich ulozist RA odpadu a kriteria prijatelnosti techto odpadu k ukladani

    Energy Technology Data Exchange (ETDEWEB)

    Kortus, J [Chemoprojekt, Prague (Czechoslovakia)

    1988-06-01

    Surface type regional depositories for radioactive wastes from nuclear power plants are described in detail. The depository of the Mochovce nuclear power plant is located near the plant, that of the Dukovany nuclear power plant is directly on the premises of the plant. Particular attention is paid to the design of the monolithic reinforced concrete pits, draining of rainwater from their surface, draining of seeping rainwater from the pit environment by means of a double drainage system, and insulation of the pits against water. The construction of the Mochovce depository started in 1987; some experience gained from this activity is presented. The radioactive waste acceptance criteria for depositories of this kind, based on safety analysis, are given. (author). 2 figs.

  12. Official criteria for diagnostics of diabetes mellitus, normoglycemia and glycemic self-control

    Directory of Open Access Journals (Sweden)

    O.V. Kaminskiy

    2017-04-01

    Full Text Available The paper considers the questions of diagnostics of diabetes mellitus (DM and early violations of carbohydrate metabolism. Venous plasma was underlined to be the only commonly accepted standard for blood glucose determination for prediabetes and diabetes mellitus diagnosis. In the third world countries (including Ukraine peripheral (capillary plasma of blood can be used for self-control and diagnostics of prediabetes and DM as their fasting values correspond to those of venous plasma and do not require revaluation. While using portable glucometers for carbohydrate violations diagnostics postprandial glucose value and after meal should be estimated in conversion. Normoglycemia is glucose concentration in venous plasma from 3.9 mmol/l (ADA criteria to 6.0 mmol/l (WHO criteria.

  13. US Department of Energy acceptance of commercial transuranic waste

    International Nuclear Information System (INIS)

    Taboas, A.L.; Bennett, W.S.; Brown, C.M.

    1980-02-01

    Contaminated transuranic wastes generated as a result of non-defense activities have been disposed of by shallow land burial at a commercially operated (NECO) facility located on the Hanford federal reservation, which is licensed by the State of Washington and by the NRC. About 15,000 ft 3 of commercial TRU waste have been generated each year, but generation for the next three years could triple due to decontamination and decommissioning scheduled to start in 1980. Disposal at other commercial burial sites has been precluded due to sites closing or prohibitions on acceptance of transuranic wastes. The State of Washington recently modified the NECO-Hanford operating license, effective February 29, 1980, to provide that radioactive wastes contaminated with transuranics in excess of 10 nCi/g will not be accepted for disposal. Consistent with the state policy, the NRC amended the NECO special nuclear material license so that Pu in excess of 10n Ci/g cannot be accepted after February 29, 1980. As a result, NRC requested DOE to examine the feasibility of accepting these wastes at a DOE operated site. TRU wastes accepted by the DOE would be placed in retrievable storage in accordance with DOE policy which requires retrievable storage of transuranic wastes pending final disposition in a geologic repository. DOE transuranic wastes are stored at six major DOE sites: INEL, Hanford, LASL, NTS, ORNL, and SRP. A specific site for receiving commercial TRU waste has not yet been selected. Shipments to DOE-Hanford would cause the least disruption to past practices. Commercial TRU wastes would be subject to waste form and packaging criteria established by the DOE. The waste generators would be expected to incur all applicable costs for DOE to take ownership of the waste, and provide storage, processing, and repository disposal. The 1980 charge to generators for DOE acceptance of commercial TRU waste is $147 per cubic foot

  14. Plugging criteria for steam generator tubes with axial cracks near tube support plates

    International Nuclear Information System (INIS)

    Mattar Neto, Miguel

    2000-01-01

    Stress corrosion cracking with intergranular attack occurs on the secondary side of steam generator (SG) tubes where impurities concentrate due to boiling under restricted flow conditions. In the most of cases, it can be called ODSCC (Outer Diameter Stress Corrosion Cracking). The typical locations are areas near support plates, in sludge piles and at top of tubesheet crevices. Though it can also occur on free spans under the relatively thin deposits that build up on the tube surfaces. ODSCC near tube plate supports have been the cause of plugging of many tubes. Thus, studies on SG tubes plugging criteria related to this degradation mechanism are presented in this paper. Th purpose is to avoid unnecessary tube plugging from either safety or reliability standpoint. Based on these studies some conclusions on the plugging criteria and on the difficulties to apply them are addressed. (author)

  15. Some considerations for establishing seismic design criteria for nuclear plant piping

    International Nuclear Information System (INIS)

    Chen, W.P.; Chokshi, N.C.

    1997-01-01

    The Energy Technology Engineering Center (ETEC) is providing assistance to the U.S. NRC in developing regulatory positions on the seismic analysis of piping. As part of this effort, ETEC previously performed reviews of the ASME Code, Section III piping seismic design criteria as revised by the 1994 Addenda. These revised criteria were based on evaluations by the ASME Special Task Group on Integrated Piping Criteria (STGIPC) and the Technical Core Group (TCG) of the Advanced Reactor Corporation (ARC) of the earlier joint Electric Power Research Institute (EPRI)/NRC Piping ampersand Fitting Dynamic Reliability (PFDR) program. Previous ETEC evaluations reported at the 23rd WRSM of seismic margins associated with the revised criteria are reviewed. These evaluations had concluded, in part, that although margins for the timed PFDR tests appeared acceptable (>2), margins in detuned tests could be unacceptable (<1). This conclusion was based primarily on margin reduction factors (MRFs) developed by the ASME STGIPC and ARC/TCG from realistic analyses of PFDR test 36. This paper reports more recent results including: (1) an approach developed for establishing appropriate seismic margins based on PRA considerations, (2) independent assessments of frequency effects on margins, (3) the development of margins based on failure mode considerations, and (4) the implications of Code Section III rules for Section XI

  16. Design criteria for piping and nozzles program

    International Nuclear Information System (INIS)

    Moore, S.E.; Bryson, J.W.

    1977-01-01

    This report reviews the activities and accomplishments of the Design Criteria for Piping and Nozzles program being conducted by the Oak Ridge National Laboratory for the period July 1, 1975, to September 30, 1976. The objectives of the program are to conduct integrated experimental and analytical stress analysis studies of piping system components and isolated and closely-spaced pressure vessel nozzles in order to confirm and/or improve the adequacy of structural design criteria and analytical methods used to assure the safe design of nuclear power plants. Activities this year included the development of a finite-element program for analyzing two closely spaced nozzles in a cylindrical pressure vessel; a limited-parameter study of vessels with isolated nozzles, finite-element studies of piping elbows, a fatigue test of an out-of-round elbow, summary and evaluation of experimental studies on the elastic-response and fatigue failure of tees, parameter studies on the behavior of flanged joints, publication of fifteen topical reports and papers on various experimental and analytical studies; and the development and acceptance of a number of design rules changes to the ASME Code. 2 figures, 2 tables

  17. Rational use of anchor pile material of the thin retaining walls

    Directory of Open Access Journals (Sweden)

    Yushkov Boris Semenovich

    2014-12-01

    Full Text Available The article considers the urgency of application of the reinforced concrete anchor piles in the constructions of retaining structures associated with the possibility of establishing rigid joint of element interface and more durable pile constructions in the soil. The features of the inclined anchor piles work as a part of sheet-pile retaining walls are noted. There was performed a study of the stress-strain state of the inclined reinforced concrete anchor piles of the thin sheet-pile wall with the reinforced concrete face members of T-section, combined with piles by a longitudinal beam. The authors consider a constructive scheme of retaining structure and list the applied loads. The efforts in the anchor piles were determined. The bending-moment curves show the character of the force distribution along the pile. A form of the pile ensuring the rational distribution of material along the pile is presented. The distribution of efforts along the length and effect of filling on its operation in the soil were accepted as the criteria of construction solution for a pile. The substantiation of the proposed design of pile is presented in terms of its stress-strain state and the rational use of material. The authors made conclusions on the reasonability of adopted design solutions associated with an increase in the flexural strength of pile, increment of the ultimate pullout capacity, stability improvement, effective use of backfill and exception of the «out of operation» areas of the pile.

  18. Use of DOE site selection criteria for screening low-level waste disposal sites on the Oak Ridge Reservation

    International Nuclear Information System (INIS)

    Lee, D.W.; Ketelle, R.H.; Stinton, L.H.

    1983-09-01

    The proposed Department of Energy (DOE) site selection criteria were applied to the Oak Ridge Reservation, and the application was evaluated to determine the criteria's usefulness in the selection of a low-level waste disposal site. The application of the criteria required the development of a methodology to provide a framework for evaluation. The methodology is composed of site screening and site characterization stages. The site screening stage relies on reconnaissance data to identify a preferred site capable of satisfying the site selection criteria. The site characterization stage relies on a detailed site investigation to determine site acceptability. The site selection criteria were applied to the DOE Oak Ridge Reservation through the site screening stage. Results of this application were similar to those of a previous siting study on the Oak Ridge Reservation. The DOE site selection criteria when coupled with the methodology that was developed were easily applied and would be adaptable to any region of interest

  19. Neutron absorber qualification and acceptance testing from the designer's perspective

    International Nuclear Information System (INIS)

    Bracey, W.; Chiocca, R.

    2004-01-01

    Starting in the mid 1990's, the USNRC began to require less than 100% credit for the 10B present in fixed neutron absorbers spent fuel transport packages. The current practice in the US is to use only 75% of the specified 10B in criticality safety calculations unless extensive acceptance testing demonstrates both the presence of the 10B and uniformity of its distribution. In practice, the NRC has accepted no more than 90% credit for 10B in recent years, while other national competent authorities continue to accept 100%. More recently, with the introduction of new neutron absorber materials, particularly aluminum / boron carbide metal matrix composites, the NRC has also expressed expectations for qualification testing, based in large part on Transnuclear's successful application to use a new composite material in the TN-68 storage / transport cask. The difficulty is that adding more boron than is really necessary to a metal has some negative effects on the material, reducing the ductility and the thermal conductivity, and increasing the cost. Excessive testing requirements can have the undesired effect of keeping superior materials out of spent fuel package designs, without a corresponding justification based on public safety. In European countries and especially in France, 100% credit has been accepted up to now with materials controls specified in the Safety Analysis Report (SAR): Manufacturing process approved by qualification testing Materials manufacturing controlled under a Quality Assurance system. During fabrication, acceptance testing directly on products or on representative samples. Acceptance criteria taking into account a statistical uncertainty corresponding to 3σ. The original and current bases for the reduced 10 B credit, the design requirements for neutron absorber materials, and the experience of Transnuclear and Cogema Logistics with neutron absorber testing are examined. Guidelines for qualification and acceptance testing and process controls

  20. Acceptance of non-fuel assembly hardware by the Federal Waste Management System

    International Nuclear Information System (INIS)

    1990-03-01

    This report is one of a series of eight prepared by E. R. Johnson Associates, Inc. (JAI) under ORNL's contract with DOE's OCRWM Systems Integration Program and in support of the Annual Capacity Report (ACR) Issue Resolution Process. The report topics relate specifically to the list of high-priority technical waste acceptance issues developed jointly by DOE and a utility-working group. JAI performed various analyses and studies on each topic to serve as starting points for further discussion and analysis leading eventually to finalizing the process by which DOE will accept spent fuel and waste into its waste management system. The eight reports are concerned with the conditions under which spent fuel and high-level waste will be accepted in the following categories: failed fuel; consolidated fuel and associated structural parts; non-fuel-assembly hardware; fuel in metal storage casks; fuel in multi-element sealed canisters; inspection and testing requirements for wastes; canister criteria; spent fuel selection for delivery; and defense and commercial high-level waste packages. 14 refs., 12 figs., 43 tabs

  1. Priority setting of health interventions: the need for multi-criteria decision analysis

    Directory of Open Access Journals (Sweden)

    Baltussen Rob

    2006-08-01

    Full Text Available Abstract Priority setting of health interventions is often ad-hoc and resources are not used to an optimal extent. Underlying problem is that multiple criteria play a role and decisions are complex. Interventions may be chosen to maximize general population health, to reduce health inequalities of disadvantaged or vulnerable groups, ad/or to respond to life-threatening situations, all with respect to practical and budgetary constraints. This is the type of problem that policy makers are typically bad at solving rationally, unaided. They tend to use heuristic or intuitive approaches to simplify complexity, and in the process, important information is ignored. Next, policy makers may select interventions for only political motives. This indicates the need for rational and transparent approaches to priority setting. Over the past decades, a number of approaches have been developed, including evidence-based medicine, burden of disease analyses, cost-effectiveness analyses, and equity analyses. However, these approaches concentrate on single criteria only, whereas in reality, policy makers need to make choices taking into account multiple criteria simultaneously. Moreover, they do not cover all criteria that are relevant to policy makers. Therefore, the development of a multi-criteria approach to priority setting is necessary, and this has indeed recently been identified as one of the most important issues in health system research. In other scientific disciplines, multi-criteria decision analysis is well developed, has gained widespread acceptance and is routinely used. This paper presents the main principles of multi-criteria decision analysis. There are only a very few applications to guide resource allocation decisions in health. We call for a shift away from present priority setting tools in health – that tend to focus on single criteria – towards transparent and systematic approaches that take into account all relevant criteria

  2. Responsible technology acceptance

    DEFF Research Database (Denmark)

    Toft, Madeleine Broman; Schuitema, Geertje; Thøgersen, John

    2014-01-01

    As a response to climate change and the desire to gain independence from imported fossil fuels, there is a pressure to increase the proportion of electricity from renewable sources which is one of the reasons why electricity grids are currently being turned into Smart Grids. In this paper, we focus...... on private consumers’ acceptance of having Smart Grid technology installed in their home. We analyse acceptance in a combined framework of the Technology Acceptance Model and the Norm Activation Model. We propose that individuals are only likely to accept Smart Grid technology if they assess usefulness...... in terms of a positive impact for society and the environment. Therefore, we expect that Smart Grid technology acceptance can be better explained when the well-known technology acceptance parameters included in the Technology Acceptance Model are supplemented by moral norms as suggested by the Norm...

  3. Radiological control criteria for materials considered for recycle and reuse

    International Nuclear Information System (INIS)

    Kennedy, W.E. Jr.; Hill, R.L.; Aaberg, R.L.; Wallo, A. III.

    1995-01-01

    Pacific Northwest Laboratory (PNL) is conducting technical analyses to support the U.S. Department of Energy (DOE), Office of Environmental Guidance, Air, Water, and Radiation Division (DOE/EH-232) in developing radiological control criteria for recycling or reuse of metals or equipment containing residual radioactive contamination from DOE operations. The criteria, framed as acceptable concentrations for release of materials for recycling or reuse, are risk-based and were developed through analysis of generic radiation exposure scenarios and pathways. The analysis includes evaluation of relevant radionuclides, potential mechanisms of exposure, and non-health-related impacts of residual radioactivity on electronics and film. The analysis considers 42 key radionuclides that DOE operations are known to generate and that may be contained in recycled or reused metals or equipment. The preliminary results are compared with similar results reported by the International Atomic Energy Agency, by radionuclide grouping. (author)

  4. Reliability Criteria for Thick Bonding Wire

    Directory of Open Access Journals (Sweden)

    Turker Dagdelen

    2018-04-01

    Full Text Available Bonding wire is one of the main interconnection techniques. Thick bonding wire is widely used in power modules and other high power applications. This study examined the case for extending the use of traditional thin wire reliability criteria, namely wire flexure and aspect ratio, to thick wires. Eleven aluminum (Al and aluminum coated copper (CucorAl wire samples with diameter 300 μm were tested experimentally. The wire response was measured using a novel non-contact method. High fidelity FEM models of the wire were developed and validated. We found that wire flexure is not correlated to its stress state or fatigue life. On the other hand, aspect ratio is a consistent criterion of thick wire fatigue life. Increasing the wire aspect ratio lowers its critical stress and increases its fatigue life. Moreover, we found that CucorAl wire has superior performance and longer fatigue life than Al wire.

  5. Evaluating and improving the performance of thin film force sensors within body and device interfaces.

    Science.gov (United States)

    Likitlersuang, Jirapat; Leineweber, Matthew J; Andrysek, Jan

    2017-10-01

    Thin film force sensors are commonly used within biomechanical systems, and at the interface of the human body and medical and non-medical devices. However, limited information is available about their performance in such applications. The aims of this study were to evaluate and determine ways to improve the performance of thin film (FlexiForce) sensors at the body/device interface. Using a custom apparatus designed to load the sensors under simulated body/device conditions, two aspects were explored relating to sensor calibration and application. The findings revealed accuracy errors of 23.3±17.6% for force measurements at the body/device interface with conventional techniques of sensor calibration and application. Applying a thin rigid disc between the sensor and human body and calibrating the sensor using compliant surfaces was found to substantially reduce measurement errors to 2.9±2.0%. The use of alternative calibration and application procedures is recommended to gain acceptable measurement performance from thin film force sensors in body/device applications. Copyright © 2017 IPEM. Published by Elsevier Ltd. All rights reserved.

  6. 'Self body-management and thinness in youth: survey study on Italian girls'.

    Science.gov (United States)

    Di Giacomo, Dina; De Liso, Giulia; Ranieri, Jessica

    2018-06-08

    Adherence to the thinness model, self-acceptance such as self-esteem is psychological dynamics influencing the young age and emerging adulthood of women life. The purpose of this study was to investigate the girls and young women' ability to deal with the adherence to thinness model according to their self-body management thought daily self-perception of ownhabits and aptitude. We analysed their emotional patterns and body management to elucidate the Italian phenomenon. A cross-sectional study was conducted on 2287 Italian female distribute in range age 15-25 years old and distributed in girl and young women groups. We conducted a Survey study by snowball sampling technique. Our results showed that girls had higher emotional pattern scores when their weight and shape fit the thinness model: skinny girls felt positively about their body even if when they did not take adequate care of it. Italian girls consider the underweight body mass index an adherence model. Findings suggest the urgent need to plan prevention programme to model healthy behaviours about their daily good practice overcoming social and cultural models based on appearance.

  7. Acceptance of Others, Feeling of Being Accepted and Striving for Being Accepted Among the Representatives of Different Kinds of Occupations

    Directory of Open Access Journals (Sweden)

    Gergana Stanoeva

    2012-05-01

    Full Text Available This paper deals with an important issue related to the human attitudes and needs in interpersonal and professional aspects. The theoretical part deals with several psychological components of the self-esteem and esteem of the others – acceptance of the others, feeling of being accepted, need for approval. Some gender differences in manifestations of acceptance and feeling of being accepted at the workplace are discussed. This article presents some empirical data for the degree of acceptance of others, feeling of being accepted and the strive for being accepted among the representatives of helping, pedagogical, administrative and economic occupations, as well as non-qualified workers. The goals of the study were to reveal the interdependency between these constructs and to be found some significant differences between the representatives of the four groups of occupations. The methods of the first study were W. Fey’s scales “Acceptance of others”, and “How do I feel accepted by others”. The method of the second study was Crown and Marlowe Scale for Social Desirability. The results indicated some significant differences in acceptance of others and feeling of being accepted between the non-qualified workers and the representatives of helping, administrative and economic occupations. There were not any significant difference in strive for being accepted between the fouroccupational groups.

  8. Social acceptability of climate change policies; will energy efficiency always fail to win its case through the consultation process? Volume 1

    International Nuclear Information System (INIS)

    Pett, Jacky

    2007-01-01

    Which segments of society 'win' as a result of climate change policies? Actors generally support the principle of reduced emissions through decarbonising fuels, and many are convinced that reducing overall energy consumption is an essential strategy to prevent further damaging climate change. However, proposed strategies for ensuring that sufficient action is taken to reduce emissions suffer from complexity, uncertainty and dissent, especially from vested interests. The policy maker has to choose between many options, and many conflicting consultation responses, to select the most politically feasible and socially acceptable pathway. An FP6 funded project into Adaptation and Mitigation Strategies for climate change is developing an innovative tool to support policy choice based on a mix of methods, using case studies to test the outputs. Resources include stakeholder deliberation on criteria necessary to evaluate pathway options. The first stage maps energy actors' perspectives of climate change, identifying key issues for socially acceptable policies for the 2012 - 2050 period that would either limit climate change to only 2 deg C increase, or provide a 'soft landing' to a world 5 degrees above present.This paper describes this mapping exercise and indicates the issues of most debate, on which rest the criteria for social acceptability. It describes how deliberative methods can involve stakeholders more effectively in policy formation, contrasts the roles of deliberation and consultation, and discusses the engagement of powerful vested interests with this approach. While there are considerable overlaps in perspectives of different actors, leading to specific points of contention, importantly, decisions on selection and engagement of stakeholders with the process become critical if the criteria for policy decisions are to be accepted by society

  9. Development of a Thin-Wall Magnesium side door Inner Panel for Automobiles

    Energy Technology Data Exchange (ETDEWEB)

    Jekl, J.; Auld, J.; Sweet, C.; Carter, Jon; Resch, Steve; Klarner, A.; Brevick, J.; Luo, A.

    2015-05-17

    Cast magnesium side door inner panels can provide a good combination of weight, functional, manufacturing and economical requirements. However, several challenges exist including casting technology for thin-wall part design, multi-material incompatibility and relatively low strength vs steel. A project has been initiated, supported by the US Department of Energy, to design and develop a lightweight frame-under-glass door having a thin-wall, full die-cast, magnesium inner panel. This development project is the first of its kind within North America. Phase I of the project is now complete and the 2.0mm magnesium design, through casting process enablers, has met or exceeded all stiffness requirements, with significant mass reduction and part consolidation. In addition, a corrosion mitigation strategy has been established using industry-accepted galvanic isolation methods and coating technologies.

  10. Nano-Photonic Structures for Light Trapping in Ultra-Thin Crystalline Silicon Solar Cells

    Directory of Open Access Journals (Sweden)

    Prathap Pathi

    2017-01-01

    Full Text Available Thick wafer-silicon is the dominant solar cell technology. It is of great interest to develop ultra-thin solar cells that can reduce materials usage, but still achieve acceptable performance and high solar absorption. Accordingly, we developed a highly absorbing ultra-thin crystalline Si based solar cell architecture using periodically patterned front and rear dielectric nanocone arrays which provide enhanced light trapping. The rear nanocones are embedded in a silver back reflector. In contrast to previous approaches, we utilize dielectric photonic crystals with a completely flat silicon absorber layer, providing expected high electronic quality and low carrier recombination. This architecture creates a dense mesh of wave-guided modes at near-infrared wavelengths in the absorber layer, generating enhanced absorption. For thin silicon (<2 μm and 750 nm pitch arrays, scattering matrix simulations predict enhancements exceeding 90%. Absorption approaches the Lambertian limit at small thicknesses (<10 μm and is slightly lower (by ~5% at wafer-scale thicknesses. Parasitic losses are ~25% for ultra-thin (2 μm silicon and just 1%–2% for thicker (>100 μm cells. There is potential for 20 μm thick cells to provide 30 mA/cm2 photo-current and >20% efficiency. This architecture has great promise for ultra-thin silicon solar panels with reduced material utilization and enhanced light-trapping.

  11. Value/impact of design criteria for cast ductile iron shipping casks

    International Nuclear Information System (INIS)

    1983-01-01

    The ductile failure criteria proposed in the Base report appear appropriate except that stress intensity values, S/sub m/ should be based on lower safety factors and ductility should be added as a criterion. A safety factor for stress intensity, s/sub m/ of 4 is recommended rather than 3 on minimum ultimate tensile strength, S/sub u/ in accordance with ASME code philosophy of assigning higher safety factors to cast ductile iron than to steel. This more conservative approach has no impact on costs since the selection of wall thickness is controlled by shielding rather than by stress considerations. The addition of a ductility criterion is recommended because of the problems associated with the selection of appropriate brittle failure criteria and the potential for cast ductile iron to have extremely low elongation at failure. Neither a materials nor a linear elastic fracture mechanics (LEFM) approach appear to be viable for demonstrating the prevention of brittle failure in cast ductile iron shipping casks. It is possible that the analytic methods predict brittle failure because of extremely conservative assumptions whereas real casks may not fail. Model drop tests could be used to demonstrate containment integrity. It is estimated that a risk committment of at least $1,000,000 would be required for engineering, design, model fabrication and testing. Before taking such risks, a mechanism should be found to obtain concurrence from NRC that the results of the test would be acceptable. Probabilistic approaches or model testing could be used to demonstrate the acceptability of cast ductile iron casks from a brittle failure point of view. Before probabilistic methods can be used, the NRC would have to be persuaded to accept the approach of the Competent Authority in West Germany or more formalized methods for probabilistic risk assessments

  12. Thin-Section Diffusion-Weighted Magnetic Resonance Imaging of the Brain with Parallel Imaging

    International Nuclear Information System (INIS)

    Oner, A.Y.; Celik, H.; Tali, T.; Akpek, S.; Tokgoz, N.

    2007-01-01

    Background: Thin-section diffusion-weighted imaging (DWI) is known to improve lesion detectability, with long imaging time as a drawback. Parallel imaging (PI) is a technique that takes advantage of spatial sensitivity information inherent in an array of multiple-receiver surface coils to partially replace time-consuming spatial encoding and reduce imaging time. Purpose: To prospectively evaluate a 3-mm-thin-section DWI technique combined with PI by means of qualitative and quantitative measurements. Material and Methods: 30 patients underwent conventional echo-planar (EPI) DWI (5-mm section thickness, 1-mm intersection gap) without parallel imaging, and thin-section EPI-DWI with PI (3-mm section thickness, 0-mm intersection gap) for a b value of 1000 s/mm 2 , with an imaging time of 40 and 80 s, respectively. Signal-to-noise ratio (SNR), relative signal intensity (rSI), and apparent diffusion coefficient (ADC) values were measured over a lesion-free cerebral region on both series by two radiologists. A quality score was assigned for each set of images to assess the image quality. When a brain lesion was present, contrast-to-noise ratio (CNR) and corresponding ADC were also measured. Student t-tests were used for statistical analysis. Results: Mean SNR values of the normal brain were 33.61±4.35 and 32.98±7.19 for conventional and thin-slice DWI (P>0.05), respectively. Relative signal intensities were significantly higher on thin-section DWI (P 0.05). Quality scores and overall lesion CNR were found to be higher in thin-section DWI with parallel imaging. Conclusion: A thin-section technique combined with PI improves rSI, CNR, and image quality without compromising SNR and ADC measurements in an acceptable imaging time. Keywords: Brain; DWI; parallel imaging; thin section

  13. Acute eosinophilic pneumonia: Thin-section CT findings in 29 patients

    International Nuclear Information System (INIS)

    Daimon, Tadahisa; Johkoh, Takeshi; Sumikawa, Hiromitsu; Honda, Osamu; Fujimoto, Kiminori; Koga, Takeharu; Arakawa, Hiroaki; Yanagawa, Masahiro; Inoue, Atsuo; Mihara, Naoki; Tomiyama, Noriyuki

    2008-01-01

    Purpose: To determine thin-section computed tomography (CT) characteristics of acute eosinophilic pneumonia (AEP). Materials and methods: Thin-section CT scans of 29 patients (14 males, 15 females; mean age, 26 ± 15 years; age range, 15-72 years) with AEP were included this retrospective study. The clinical diagnosis of AEP was established by Allen's criteria. Each thin-section CT was reviewed by two observers. Results: Bilateral areas with ground-glass attenuation were observed on thin-section CT in all patients. Areas of air-space consolidation were present in 16 (55%) of 29 patients. Poorly defined centrilobular nodules were present in 9 patients (31%). Interlobular septal thickening was present in 26 patients (90%). Thickening of bronchovascular bundles was present in 19 patients (66%). Pleural effusions were present in 23 patients (79%) (bilateral = 22, right side = 1, left side = 0). The predominant overall anatomic distribution was central in only 2 (7%) of 29 patients, peripheral in 9 patients (31%), and random in 18 patients (62%). The overall zonal predominance was upper in 4 patients (14%), lower in 8 patients (28%), and random in 17 patients (58%). Conclusion: CT findings in AEP patients consisted mainly of bilateral areas of ground-glass attenuation, interlobular septal thickening, thickening of bronchovascular bundles, and the presence of a pleural effusion without cardiomegaly. The most common overall anatomic distribution and zonal predominance of the abnormal CT findings were random

  14. Acute eosinophilic pneumonia: Thin-section CT findings in 29 patients

    Energy Technology Data Exchange (ETDEWEB)

    Daimon, Tadahisa [Department of Radiology, Osaka University Medical School, 2-2 Yamadaoka, Suita, Osaka 565-0871 (Japan); Department of Medicine, Division of Pulmonary Medicine, Jichi Medical University, Yakushiji 3311-1, Shimotsuke, Tochigi 329-0498 (Japan)], E-mail: t-daimon@radiol.med.osaka-u.ac.jp; Johkoh, Takeshi [Department of Radiology, Osaka University Medical School, 2-2 Yamadaoka, Suita, Osaka 565-0871 (Japan)], E-mail: johkoh@sahs.med.osaka-u.ac.jp; Sumikawa, Hiromitsu [Department of Radiology, Osaka University Medical School, 2-2 Yamadaoka, Suita, Osaka 565-0871 (Japan)], E-mail: h-sumikawa@radiol.med.osaka-u.ac.jp; Honda, Osamu [Department of Radiology, Osaka University Medical School, 2-2 Yamadaoka, Suita, Osaka 565-0871 (Japan)], E-mail: ohonda@radiol.med.osaka-u.ac.jp; Fujimoto, Kiminori [Department of Radiology, Kurume University School of Medicine, 67 Asahi-machi, Kurume 830-0011 (Japan)], E-mail: kimichan@med.kurume-u.ac.jp; Koga, Takeharu [Department of Medicine, Division of Respirology and Neurology, Kurume University School of Medicine, 67 Asahi-machi, Kurume 830-0011 (Japan)], E-mail: kogat@med.kurume-u.ac.jp; Arakawa, Hiroaki [Department of Radiology, Dokkyo University School of Medicine, 880 Kita-Kobayashi, Mibu, Tochigi 321-0293 (Japan)], E-mail: arakawa@dokkyomed.ac.jp; Yanagawa, Masahiro [Department of Radiology, Osaka University Medical School, 2-2 Yamadaoka, Suita, Osaka 565-0871 (Japan)], E-mail: m-yanagawa@radiol.med.osaka-u.ac.jp; Inoue, Atsuo [Department of Radiology, Osaka University Medical School, 2-2 Yamadaoka, Suita, Osaka 565-0871 (Japan)], E-mail: ainoue@radiol.med.osaka-u.ac.jp; Mihara, Naoki [Department of Radiology, Osaka University Medical School, 2-2 Yamadaoka, Suita, Osaka 565-0871 (Japan)], E-mail: nmihara@radiol.med.osaka-u.ac.jp; Tomiyama, Noriyuki [Department of Radiology, Osaka University Medical School, 2-2 Yamadaoka, Suita, Osaka 565-0871 (Japan)], E-mail: tomiyama@radiol.med.osaka-u.ac.jp (and others)

    2008-03-15

    Purpose: To determine thin-section computed tomography (CT) characteristics of acute eosinophilic pneumonia (AEP). Materials and methods: Thin-section CT scans of 29 patients (14 males, 15 females; mean age, 26 {+-} 15 years; age range, 15-72 years) with AEP were included this retrospective study. The clinical diagnosis of AEP was established by Allen's criteria. Each thin-section CT was reviewed by two observers. Results: Bilateral areas with ground-glass attenuation were observed on thin-section CT in all patients. Areas of air-space consolidation were present in 16 (55%) of 29 patients. Poorly defined centrilobular nodules were present in 9 patients (31%). Interlobular septal thickening was present in 26 patients (90%). Thickening of bronchovascular bundles was present in 19 patients (66%). Pleural effusions were present in 23 patients (79%) (bilateral = 22, right side = 1, left side = 0). The predominant overall anatomic distribution was central in only 2 (7%) of 29 patients, peripheral in 9 patients (31%), and random in 18 patients (62%). The overall zonal predominance was upper in 4 patients (14%), lower in 8 patients (28%), and random in 17 patients (58%). Conclusion: CT findings in AEP patients consisted mainly of bilateral areas of ground-glass attenuation, interlobular septal thickening, thickening of bronchovascular bundles, and the presence of a pleural effusion without cardiomegaly. The most common overall anatomic distribution and zonal predominance of the abnormal CT findings were random.

  15. Acceptance and adoption of biofortified crops in low- and middle-income countries: a systematic review

    Science.gov (United States)

    Talsma, Elise F; Melse-Boonstra, Alida; Brouwer, Inge D

    2017-01-01

    Context: Biofortification of staple crops is a promising strategy for increasing the nutrient density of diets in order to improve human health. The willingness of consumers and producers to accept new crop varieties will determine whether biofortification can be successfully implemented. Objective: This review assessed sensory acceptance and adoption of biofortified crops and the determining factors for acceptance and adoption among consumers and producers in low- and middle-income countries. Data sources: PubMed, Scopus, and Web of Science were searched for published reports. Unpublished studies were identified using an internet search. Study selection: From a total of 1669 records found, 72 primary human research studies published in English or Spanish met the criteria for inclusion. Data extraction: Data were extracted from each identified study using a standardized form. Results: Sensory acceptability (n = 40) was the most common topic of the studies, followed by determinants of acceptance (n = 25) and adoption (n = 21). Of crops included in the studies, sweet potato and maize were the most studied, whereas rice and pearl-millet were the least investigated. Overall, sensory acceptance was good, and availability and information on health benefits of the crops were the most important determinants of acceptance and adoption. Conclusions: Changes to the sensory qualities of a crop, including changes in color, did not act as an obstacle to acceptance of biofortified crops. Future studies should look at acceptance of biofortified crops after they have been disseminated and introduced on a wide-scale. PMID:29028269

  16. An Evaluation of Industry Relationships Among Contributors to AAOS Clinical Practice Guidelines and Appropriate Use Criteria.

    Science.gov (United States)

    Checketts, Jake X; Cook, Courtney; Vassar, Matt

    2018-01-17

    A long-standing relationship between orthopaedic surgeons and industry has made financial conflicts of interest a concerning issue. Research supports that financial conflicts of interest can influence both medical research and clinical practice. Financial conflicts of interest may also influence clinical practice guideline recommendations and their corresponding appropriate use criteria. Because of the influential nature of these guidelines, it is imperative that care be taken to minimize bias during guideline development. We retrieved clinical practice guidelines and their corresponding appropriate use criteria from the American Academy of Orthopaedic Surgery that were published or revised between 2013 and 2016. We extracted industry payments received by physicians using the Centers for Medicare & Medicaid Services Open Payments database. We then evaluated the value and types of these payments. We also used these data to determine whether disclosure statements were accurate and whether guideline development was in adherence with the Institute of Medicine's (IOM's) standards. Of the 106 physicians that were evaluated, 85 (80%) received at least 1 industry payment, 56 (53%) accepted >$1,000, and 35 (33%) accepted >$10,000. Financial payments amounted to a mean of $93,512 per physician. Total reimbursement for the 85 clinical practice guideline and appropriate use criteria contributors was $9,912,309. We found that disclosure statements disagreed with the Open Payments data and that the IOM standards were not completely enforced. Clinical practice guideline and appropriate use criteria contributors received substantial payments from industry, many disclosure statements were inaccurate, and the IOM standards were not completely met. Clinical practice guidelines and appropriate use criteria are critical for practicing evidence-based medicine. If financial conflicts of interest are present during their development, it is possible that patient care may be compromised.

  17. Acceptance and Commitment Therapy Group Treatment for Symptoms of Borderline Personality Disorder: A Public Sector Pilot Study

    Science.gov (United States)

    Morton, Jane; Snowdon, Sharon; Gopold, Michelle; Guymer, Elise

    2012-01-01

    A pilot study of a brief group-based Acceptance and Commitment Therapy (ACT) intervention (12 two-hour sessions) was conducted with clients of public mental health services meeting four or more criteria for borderline personality disorder (BPD). Participants were randomly assigned to receive the ACT group intervention in addition to their current…

  18. Control criteria for residual contamination in materials considered for recycle and reuse

    International Nuclear Information System (INIS)

    Kennedy, W.E. Jr.; Hill, R.L.; Aaberg, R.L.

    1993-11-01

    Pacific Northwest Laboratory (PNL) is collecting data and conducting technical analyses to support the US Department of Energy (DOE), Office of Environmental Guidance, Air, Water, and Radiation Division (DOE/EH-232) in determining the feasibility of developing radiological control criteria for recycling or reuse of metals or equipment containing residual radioactive contamination from DOE operations. The criteria, framed as acceptable concentrations for release of materials for recycling or reuse, will be risk-based and will be developed through analysis of radiation exposure scenarios and pathways. The analysis will include evaluation of relevant radionuclides, potential mechanisms of exposure, and non-health-related impacts of residual radioactivity on electronics and film. The analyses will consider 42 key radionuclides that are generated during DOE operations and may be contained in recycled or reused metals or equipment

  19. Recommended new criteria for the selection of nuclear waste repository sites in Columbia River basalt and US Gulf Coast domed salt

    International Nuclear Information System (INIS)

    Steinborn, T.L.; Wagoner, J.L.; Qualheim, B.; Fitts, C.R.; Stetkar, R.E.; Turnbull, R.W.

    1980-01-01

    Screening criteria and specifications are recommended to aid in the evaluation of sites proposed for nuclear waste disposal in basalt and domed salt. The recommended new criteria proposed in this report are intended to supplement existing repository-related criteria for nuclear waste disposal. The existing criteria are contained in 10 CFR 60 sections which define siting criteria of the Nuclear Regulatory Commission (NRC), and ONWI 33(2) which defines siting criteria of the Office of Nuclear Waste Isolation (ONWI) for the Department of Energy. The specifications are conditions or parameter values that the authors recommend be applied in site acceptance evaluations. The siting concerns covered in this report include repository depth, host rock extent, seismic setting, structural and tectonic conditions, groundwater and rock geochemistry, volcanism, surface and subsurface hydrology, and socioeconomic issues, such as natural resources, land use, and population distribution

  20. Some selection criteria for computers in real-time systems for high energy physics

    International Nuclear Information System (INIS)

    Kolpakov, I.F.

    1980-01-01

    The right choice of program source is for the organization of real-time systems of great importance as cost and reliability are decisive factors. Some selection criteria for program sources for high energy physics multiwire chamber spectrometers (MWCS) are considered in this report. MWCS's accept bits of information from event pattens. Large and small computers, microcomputers and intelligent controllers in CAMAC crates are compared with respect to the following characteristics: data exchange speed, number of addresses for peripheral devices, cost of interfacing a peripheral device, sizes of buffer and mass memory, configuration costs, and the mean time between failures (MTBF). The results of comparisons are shown by plots and histograms which allow the selection of program sources according to the above criteria. (Auth.)

  1. Reproducibility of quantitative planar thallium-201 scintigraphy: quantitative criteria for reversibility of myocardial perfusion defects

    International Nuclear Information System (INIS)

    Sigal, S.L.; Soufer, R.; Fetterman, R.C.; Mattera, J.A.; Wackers, F.J.

    1991-01-01

    Fifty-two paired stress/delayed planar 201 TI studies (27 exercise studies, 25 dipyridamole studies) were processed twice by seven technologists to assess inter- and intraobserver variability. The reproducibility was inversely related to the size of 201 Tl perfusion abnormalities. Intraobserver variability was not different between exercise and dipyridamole studies for lesions of similar size. Based upon intraobserver variability, objective quantitative criteria for reversibility of perfusion abnormalities were defined. These objective criteria were tested prospectively in a separate group of 35 201 Tl studies and compared with the subjective interpretation of quantitative circumferential profiles. Overall, exact agreement existed in 78% of images (kappa statistic k = 0.66). We conclude that quantification of planar 201 Tl scans is highly reproducible, with acceptable inter- and intraobserver variability. Objective criteria for lesion reversibility correlated well with analysis by experienced observers

  2. Repressive coping among British college women: A potential protective factor against body image concerns, drive for thinness, and bulimia symptoms.

    Science.gov (United States)

    Mohiyeddini, Changiz

    2017-09-01

    Repressive coping, as a means of preserving a positive self-image, has been widely explored in the context of dealing with self-evaluative cues. The current study extends this research by exploring whether repressive coping is associated with lower levels of body image concerns, drive for thinness, bulimic symptoms, and higher positive rational acceptance. A sample of 229 female college students was recruited in South London. Repressive coping was measured via the interaction between trait anxiety and defensiveness. The results of moderated regression analysis with simple slope analysis show that compared to non-repressors, repressors reported lower levels of body image concerns, drive for thinness, and bulimic symptoms while exhibiting a higher use of positive rational acceptance. These findings, in line with previous evidence, suggest that repressive coping may be adaptive particularly in the context of body image. Copyright © 2017 Elsevier Ltd. All rights reserved.

  3. Mutation-specific effects on thin filament length in thin filament myopathy.

    Science.gov (United States)

    Winter, Josine M de; Joureau, Barbara; Lee, Eun-Jeong; Kiss, Balázs; Yuen, Michaela; Gupta, Vandana A; Pappas, Christopher T; Gregorio, Carol C; Stienen, Ger J M; Edvardson, Simon; Wallgren-Pettersson, Carina; Lehtokari, Vilma-Lotta; Pelin, Katarina; Malfatti, Edoardo; Romero, Norma B; Engelen, Baziel G van; Voermans, Nicol C; Donkervoort, Sandra; Bönnemann, C G; Clarke, Nigel F; Beggs, Alan H; Granzier, Henk; Ottenheijm, Coen A C

    2016-06-01

    Thin filament myopathies are among the most common nondystrophic congenital muscular disorders, and are caused by mutations in genes encoding proteins that are associated with the skeletal muscle thin filament. Mechanisms underlying muscle weakness are poorly understood, but might involve the length of the thin filament, an important determinant of force generation. We investigated the sarcomere length-dependence of force, a functional assay that provides insights into the contractile strength of muscle fibers as well as the length of the thin filaments, in muscle fibers from 51 patients with thin filament myopathy caused by mutations in NEB, ACTA1, TPM2, TPM3, TNNT1, KBTBD13, KLHL40, and KLHL41. Lower force generation was observed in muscle fibers from patients of all genotypes. In a subset of patients who harbor mutations in NEB and ACTA1, the lower force was associated with downward shifted force-sarcomere length relations, indicative of shorter thin filaments. Confocal microscopy confirmed shorter thin filaments in muscle fibers of these patients. A conditional Neb knockout mouse model, which recapitulates thin filament myopathy, revealed a compensatory mechanism; the lower force generation that was associated with shorter thin filaments was compensated for by increasing the number of sarcomeres in series. This allowed muscle fibers to operate at a shorter sarcomere length and maintain optimal thin-thick filament overlap. These findings might provide a novel direction for the development of therapeutic strategies for thin filament myopathy patients with shortened thin filament lengths. Ann Neurol 2016;79:959-969. © 2016 American Neurological Association.

  4. Acceptance of failed SNF [spent nuclear fuel] assemblies by the Federal Waste Management System

    International Nuclear Information System (INIS)

    1990-03-01

    This report is one of a series of eight prepared by E. R. Johnson Associates, Inc. (JAI) under ORNL's contract with DOE's OCRWM Systems Integration Program and in support of the Annual Capacity Report (ACR) Issue Resolution Process. The report topics relate specifically to the list of high priority technical waste acceptance issues developed jointly by DOE and a utility-working group. JAI performed various analyses and studies on each topic to serve as starting points for further discussion and analysis leading eventually to finalizing the process by which DOE will accept spent fuel and waste into its waste management system. The eight reports are concerned with the conditions under which spent fuel and high level waste will be accepted in the following categories: failed fuel; consolidated fuel and associated structural parts; non-fuel-assembly hardware; fuel in metal storage casks; fuel in multi-element sealed canisters; inspection and testing requirements for wastes; canister criteria; spent fuel selection for delivery; and defense and commercial high-level waste packages. This document discusses acceptance of failed spent fuel assemblies by the Federal Waste Management System. 18 refs., 7 figs., 25 tabs

  5. Influence of various thickness metallic interlayers on opto-electric and mechanical properties of AZO thin films on PET substrates

    Science.gov (United States)

    Chang, R. C.; Li, T. C.; Lin, C. W.

    2012-02-01

    Various thickness metallic interlayers to improve the opto-electric and mechanical properties of aluminum-doped zinc oxide (AZO) thin films deposited on flexible polyethylene terephtalate (PET) substrates are studied. The effects of the interlayers on the resistance and transmittance of the AZO thin films are discussed. The result shows that the metallic interlayers effectively improve the electric resistance but reduce the optical transmittance of the AZO thin films. These phenomena become more obvious as the interlayer thickness increases. However, the AZO with an aluminum interlayer still behaves an acceptable transmittance. Moreover, mechanical tests indicate that the aluminum interlayer increases the hardness and modulus, and reduce the residual stress of the AZO thin films. In contrast, the silver and copper interlayers decrease the AZO's mechanical properties. Comparing to those without any interlayer, the results show that the best interlayer is the 6 nm thick aluminum film.

  6. Assessing health status and quality-of-life instruments: attributes and review criteria.

    Science.gov (United States)

    Aaronson, Neil; Alonso, Jordi; Burnam, Audrey; Lohr, Kathleen N; Patrick, Donald L; Perrin, Edward; Stein, Ruth E

    2002-05-01

    The field of health status and quality of life (QoL) measurement - as a formal discipline with a cohesive theoretical framework, accepted methods, and diverse applications--has been evolving for the better part of 30 years. To identify health status and QoL instruments and review them against rigorous criteria as a precursor to creating an instrument library for later dissemination, the Medical Outcomes Trust in 1994 created an independently functioning Scientific Advisory Committee (SAC). In the mid-1990s, the SAC defined a set of attributes and criteria to carry out instrument assessments; 5 years later, it updated and revised these materials to take account of the expanding theories and technologies upon which such instruments were being developed. This paper offers the SAC's current conceptualization of eight key attributes of health status and QoL instruments (i.e., conceptual and measurement model; reliability; validity; responsiveness; interpretability; respondent and administrative burden; alternate forms; and cultural and language adaptations) and the criteria by which instruments would be reviewed on each of those attributes. These are suggested guidelines for the field to consider and debate; as measurement techniques become both more familiar and more sophisticated, we expect that experts will wish to update and refine these criteria accordingly.

  7. Evaluation of benign pulmonary lesions less than 20 mm in diameter by thin-section computed tomography

    International Nuclear Information System (INIS)

    Shiotani, Seiji; Yamada, Kouzo; Oshita, Fumihiro

    1997-01-01

    To establish diagnostic criteria for small solitary pulmonary nodules, the findings of thin-section computed tomography (CT) were compared with pathological findings. We evaluated thin-section CT images and compared them with pathological findings in 23 specimens of resected benign lesions less than 20 mm in diameter located in the peripheral region. The thin-section CT images were reconstructed using 2 mm thick sections taken by TCT-900S, HELIX (Toshiba, Tokyo) and were examined with two different windows and level settings. In every case, the surgical specimens were sliced transversely to correlate with the CT findings. The thin-section CT images were classified into two types; solid and air-containing types. The former consisted of benign pulmonary tumors, granulomas and some focal fibrosis, while the latter all consisted of focal fibrosis. Both types were difficult to distinguish from peripheral lung cancer based only on margin analysis of the lesion, but analysis of how pulmonary vessels relate to the lesion can allow benign pulmonary lesions to be distinguished from peripheral lung cancer. (author)

  8. The challenges of modelling phosphorus in a headwater catchment: Applying a 'limits of acceptability' uncertainty framework to a water quality model

    Science.gov (United States)

    Hollaway, M. J.; Beven, K. J.; Benskin, C. McW. H.; Collins, A. L.; Evans, R.; Falloon, P. D.; Forber, K. J.; Hiscock, K. M.; Kahana, R.; Macleod, C. J. A.; Ockenden, M. C.; Villamizar, M. L.; Wearing, C.; Withers, P. J. A.; Zhou, J. G.; Barber, N. J.; Haygarth, P. M.

    2018-03-01

    There is a need to model and predict the transfer of phosphorus (P) from land to water, but this is challenging because of the large number of complex physical and biogeochemical processes involved. This study presents, for the first time, a 'limits of acceptability' approach of the Generalized Likelihood Uncertainty Estimation (GLUE) framework to the Soil and Water Assessment Tool (SWAT), in an application to a water quality problem in the Newby Beck catchment (12.5 km2), Cumbria, United Kingdom (UK). Using high frequency outlet data (discharge and P), individual evaluation criteria (limits of acceptability) were assigned to observed discharge and P loads for all evaluation time steps, identifying where the model was performing well/poorly and to infer which processes required improvement in the model structure. Initial limits of acceptability were required to be relaxed by a substantial amount (by factors of between 5.3 and 6.7 on a normalized scale depending on the evaluation criteria used) in order to gain a set of behavioral simulations (1001 and 1016, respectively out of 5,000,000). Of the 39 model parameters tested, the representation of subsurface processes and associated parameters, were consistently shown as critical to the model not meeting the evaluation criteria, irrespective of the chosen evaluation metric. It is therefore concluded that SWAT is not an appropriate model to guide P management in this catchment. This approach highlights the importance of high frequency monitoring data for setting robust model evaluation criteria. It also raises the question as to whether it is possible to have sufficient input data available to drive such models so that we can have confidence in their predictions and their ability to inform catchment management strategies to tackle the problem of diffuse pollution from agriculture.

  9. Photon management in thin-film solar cells; Photon-Management in Duennschicht-Solarzellen

    Energy Technology Data Exchange (ETDEWEB)

    Fahr, Stephan

    2011-11-22

    In this thesis procedures were presented, which modify the propagation of the incident light in such a way that by this the efficiency of thin-film solar cells is increased. The strength of the presented numerical studies lies thereby in the rigorous solution of Maxwell's equations. Fundamental statements concerning the lay-out of an ideal texture could be made, which for present thin-film solar cells over the whole relevant spectral range both suppresses reflection losses and leads to an elongation of the effective path. Object of the thesis was also the design of a spectral- and angular-selective filter, which confines the acceptance angle of a solar cell with the aim of an improved absorption in the long-wave spectral region. Furthermore also tandem cells on the base of amorphous and microcrystalline silicon were studied.

  10. Effect of thinning on flower and fruit and of edible coatings on postharvest quality of jaboticaba fruit stored at low temperature

    Directory of Open Access Journals (Sweden)

    Talita Pimenta do Nascimento

    2013-09-01

    Full Text Available Jaboticaba is a Brazilian fruit, native to the Atlantic forest, which belongs to the Myrtaceae family. In this work we describe the effect of the thinning of "flower", "fruit" and "flower & fruit" compared to non-thinned fruit (control and of edible coatings with respect on nutritional composition, overall acceptability and shelf-life of jaboticaba ‘Sabara’, grown in an irrigated commercial orchard. "Flower and fruit" thinning allows fruit with higher quality as diameter, volume and mass. Non-thinned fruit shows higher yield, however fruit have lower quality. As a result of the improving quality at harvest, the shelf life was twice (~8 days for thinned fruit. The lack of change in concentration of soluble sugar and absence of formation of volatile compounds during storage indicate that there was no natural fermentation of the jaboticaba pulp after harvest. Treatments with wax and calcium did not improve the jaboticaba shelf life.

  11. Environmentally acceptable endpoints for PAHs at a manufactured gas plant site

    Energy Technology Data Exchange (ETDEWEB)

    Stroo, H.F.; Jensen, R.; Loehr, R.C.; Nakles, D.V.; Fairbrother, A.; Liban, C.B. [ThermoRetec Corp., Carson, CA (USA)

    2000-09-01

    Samples from a former manufactured gas plant (MGP) site in Santa Barbara, CA were tested to evaluate the environmentally acceptable endpoints (EAE) process for setting risk-based cleanup criteria. The research was part of an ongoing effort to develop and demonstrate a protocol for assessing risk-based criteria for MGP sites that incorporates the availability of polycyclic aromatic hydrocarbons (PAHs). Six soil samples were subjected to a battery of physical and biological tests that focused on determining the 'availability' of the soil-bound contaminants to groundwater, ecological receptors, and human receptors. Results demonstrated that sorption to soil, matrix effects, aging, and treatment can significantly reduce chemical availability. Including these reduced availability results in risk assessment calculations yielded environmentally protective cleanup levels almost 3-10 times greater than levels derived using California default risk assessment assumptions. Using an EAE-based approach for MGP soils, especially those containing lampblack, could provide more realistic risk assessment. 23 refs., 6 tabs.

  12. Alternative microbial methods: An overview and selection criteria.

    Science.gov (United States)

    Jasson, Vicky; Jacxsens, Liesbeth; Luning, Pieternel; Rajkovic, Andreja; Uyttendaele, Mieke

    2010-09-01

    This study provides an overview and criteria for the selection of a method, other than the reference method, for microbial analysis of foods. In a first part an overview of the general characteristics of rapid methods available, both for enumeration and detection, is given with reference to relevant bibliography. Perspectives on future development and the potential of the rapid method for routine application in food diagnostics are discussed. As various alternative "rapid" methods in different formats are available on the market, it can be very difficult for a food business operator or for a control authority to select the most appropriate method which fits its purpose. Validation of a method by a third party, according to international accepted protocol based upon ISO 16140, may increase the confidence in the performance of a method. A list of at the moment validated methods for enumeration of both utility indicators (aerobic plate count) and hygiene indicators (Enterobacteriaceae, Escherichia coli, coagulase positive Staphylococcus) as well as for detection of the four major pathogens (Salmonella spp., Listeria monocytogenes, E. coli O157 and Campylobacter spp.) is included with reference to relevant websites to check for updates. In a second part of this study, selection criteria are introduced to underpin the choice of the appropriate method(s) for a defined application. The selection criteria link the definition of the context in which the user of the method functions - and thus the prospective use of the microbial test results - with the technical information on the method and its operational requirements and sustainability. The selection criteria can help the end user of the method to obtain a systematic insight into all relevant factors to be taken into account for selection of a method for microbial analysis. Copyright 2010 Elsevier Ltd. All rights reserved.

  13. AAPT Diagnostic Criteria for Chronic Cancer Pain Conditions.

    Science.gov (United States)

    Paice, Judith A; Mulvey, Matt; Bennett, Michael; Dougherty, Patrick M; Farrar, John T; Mantyh, Patrick W; Miaskowski, Christine; Schmidt, Brian; Smith, Thomas J

    2017-03-01

    Chronic cancer pain is a serious complication of malignancy or its treatment. Currently, no comprehensive, universally accepted cancer pain classification system exists. Clarity in classification of common cancer pain syndromes would improve clinical assessment and management. Moreover, an evidence-based taxonomy would enhance cancer pain research efforts by providing consistent diagnostic criteria, ensuring comparability across clinical trials. As part of a collaborative effort between the Analgesic, Anesthetic, and Addiction Clinical Trial Translations, Innovations, Opportunities, and Networks (ACTTION) and the American Pain Society (APS), the ACTTION-APS Pain Taxonomy initiative worked to develop the characteristics of an optimal diagnostic system. After the establishment of these characteristics, a working group consisting of clinicians and clinical and basic scientists with expertise in cancer and cancer-related pain was convened to generate core diagnostic criteria for an illustrative sample of 3 chronic pain syndromes associated with cancer (ie, bone pain and pancreatic cancer pain as models of pain related to a tumor) or its treatment (ie, chemotherapy-induced peripheral neuropathy). A systematic review and synthesis was conducted to provide evidence for the dimensions that comprise this cancer pain taxonomy. Future efforts will subject these diagnostic categories and criteria to systematic empirical evaluation of their feasibility, reliability, and validity and extension to other cancer-related pain syndromes. The ACTTION-APS chronic cancer pain taxonomy provides an evidence-based classification for 3 prevalent syndromes, namely malignant bone pain, pancreatic cancer pain, and chemotherapy-induced peripheral neuropathy. This taxonomy provides consistent diagnostic criteria, common features, comorbidities, consequences, and putative mechanisms for these potentially serious cancer pain conditions that can be extended and applied with other cancer

  14. The acceptability of waiting times for elective general surgery and the appropriateness of prioritising patients

    Directory of Open Access Journals (Sweden)

    Knol Dirk L

    2007-02-01

    Full Text Available Abstract Background Problematic waiting lists in public health care threaten the equity and timeliness of care provision in several countries. This study assesses different stakeholders' views on the acceptability of waiting lists in health care, their preferences for priority care of patients, and their judgements on acceptable waiting times for surgical patients. Methods A questionnaire survey was conducted among 257 former patients (82 with varicose veins, 86 with inguinal hernia, and 89 with gallstones, 101 surgeons, 95 occupational physicians, and 65 GPs. Judgements on acceptable waiting times were assessed using vignettes of patients with varicose veins, inguinal hernia, and gallstones. Results Participants endorsed the prioritisation of patients based on clinical need, but not on ability to benefit. The groups had significantly different opinions (p Acceptable waiting times ranged between 2 and 25 weeks depending on the type of disorder (p Conclusion The explicit prioritisation of patients seems an accepted means for reducing the overall burden from waiting lists. The disagreement about appropriate prioritisation criteria and the need for uniformity, however, raises concern about equity when implementing prioritisation in daily practice. Single factor waiting time thresholds seem insufficient for securing timely care provision in the presence of long waiting lists as they do not account for the different consequences of waiting between patients.

  15. Analysis of Satellite AIS Data to Derive Weather Judging Criteria for Voyage Route Selection

    Directory of Open Access Journals (Sweden)

    Michio Fujii

    2017-06-01

    Full Text Available The operational limitations are discussed at the IMO as a part of the second generation intact stability criteria. Since it is a first attempt to introduce operational efforts into safety regulations, comprehensive discussions are necessary to realize practically acceptable ones. Therefore this study investigates actual navigation routes of container ships and pure car carriers in the trans-North Pacific Ocean in winter, because they are prone to suffer significant parametric roll which is one of stability failure modes. Firstly, interviews are made to shipmasters who have experiences to have operated the subject ships to identify major elements for route selection in the North Pacific Ocean. Secondly, sufficient number of actual navigation records is collected from Satellite AIS data to derive the weather criteria for the route selection in severe weather condition. Finally, shipmaster’s on-board decision-making criteria are discussed by analysing the ship tracking data and weather data.

  16. Acceptance test report, 241-SY-101 Flexible Receiver System, Phase 2 testing

    International Nuclear Information System (INIS)

    Ritter, G.A.

    1995-01-01

    This document summarizes the results of the Phase 2 acceptance test of the 241-SY-101 Flexible Receiver System (FRS). The FRS is one of six major components of the Equipment Removal System, which has been designed to retrieve, transport, and store the test mixer pump currently installed in Tank 241-SY-101. The purpose of this acceptance test is to verify the strength of the containment bag and bag bottom cinching mechanism. It is postulated that 68 gallons of waste could be trapped inside the pump internals. The bag must be capable of supporting this waste if it shakes loose and drains to the bottom of the bag after the bag bottom has been cinched closed. This acceptance test was performed at the Maintenance and Storage Facility (MASF) Facility in the 400 area on January 23, 1995. The bag assembly supported the weight of 920 kg (2,020 lbs) of water with no leakage or damage to the bag. This value meets the acceptance criteria of 910 kg of water and therefore the results were found to be acceptable. The maximum volume of liquid expected to be held up in the pump internals is 258 L (68 gallons), which corresponds to 410 kg. This test weight gives just over a safety factor of 2. The bag also supported a small shock load while it was filled with water when the crane hoisted the bag assembly up and down. Based on the strength rating of the bag components, the bag assembly should support 2--3 times the test weight of 910 kg

  17. Acceptance test report for portable exhauster POR-008/Skid F

    International Nuclear Information System (INIS)

    Kriskovich, J.R.

    1998-01-01

    Portable Exhauster POR-008 was procured via HNF-0490, Specification for a Portable Exhausted System for Waste Tank Ventilation. Prior to taking ownership, acceptance testing was performed at the vendors. However at the conclusion of testing a number of issues remained that required resolution before the exhausters could be used by Project W-320. The purpose of acceptance testing documented by this report was to demonstrate compliance of the exhausters with the performance criteria established within HNF-O49O, Rev. 1 following a repair and upgrade effort at Hanford. In addition, data obtained during this testing is required for the resolution of outstanding Non-conformance Reports (NCR), and finally, to demonstrate the functionality of the associated software for the pressure control and high vacuum exhauster operating modes provided for by W-320. Additional testing not required by the ATP was also performed to assist in the disposition and close out of receiving inspection report and for application design information (system curve). Results of this testing are also captured within this document

  18. FAD: A full-acceptance detector for physics at the SSC

    International Nuclear Information System (INIS)

    Bjorken, J.D.

    1992-09-01

    For high energy pp collisions, the concepts ''4π'' and ''full acceptance'' are distinct. At the SSC, the appropriate variables for describing phase space are the lego variables: pseudorapidity η and azimuthal angle φ. While most of 4π is covered by pseudorapidities less than 3 or 4 in magnitude, at the SSC there is very interesting physics out to η's of 9 to 12. For over a year I have been attempting to encourage an initiative at the SSC to provide a detector which could cover the missing acceptance of the two big detectors, which in particular have no appreciable charged particle tracking with good momentum resolution beyond rapidities of 2.5 or so. The nonnegotiable criteria for an FAD are for me the following: 1. All charged particles are seen and their momenta measured well, provided pt is not too large. 2. All photons are seen and their momenta are measured well. 3. The physics of rapidity-gaps is not compromised. This means angular coverage from 90 degrees down to tens of microradians. The above criteria cannot be met on day one of SSC commissioning with the amount of funds available. But I believe a staged approach is feasible, with a lot of interesting physics available along the way. The basic philosophy underlying the FAD idea is that it should first and most be a survey instrument, sensitive to almost everything, but optimized for almost nothing. Its strength is in the perception of complex patterns individual events, used as a signature of new and/or interesting physics. Examples of such patterns will be given later

  19. Respondent-driven sampling to assess mental health outcomes, stigma and acceptance among women raising children born from sexual violence-related pregnancies in eastern Democratic Republic of Congo.

    Science.gov (United States)

    Scott, Jennifer; Rouhani, Shada; Greiner, Ashley; Albutt, Katherine; Kuwert, Philipp; Hacker, Michele R; VanRooyen, Michael; Bartels, Susan

    2015-04-08

    Assess mental health outcomes among women raising children from sexual violence-related pregnancies (SVRPs) in eastern Democratic Republic of Congo and stigma toward and acceptance of women and their children. Participants were recruited using respondent-driven sampling. Bukavu, Democratic Republic of Congo in 2012. 757 adult women raising children from SVRPs were interviewed. A woman aged 18 and older was eligible for the study if she self-identified as a sexual violence survivor since the start of the conflict (∼1996), conceived an SVRP, delivered a liveborn child and was currently raising the child. A woman was ineligible for the study if the SVRP ended with a spontaneous abortion or fetal demise or the child was not currently living or in the care of the biological mother. Trained female Congolese interviewers verbally administered a quantitative survey after obtaining verbal informed consent. Symptom criteria for major depressive disorder, post-traumatic stress disorder, anxiety and suicidality were assessed, as well as stigma toward the woman and her child. Acceptance of the woman and child from the spouse, family and community were analysed. 48.6% met symptom criteria for major depressive disorder, 57.9% for post-traumatic stress disorder, 43.3% for anxiety and 34.2% reported suicidality. Women who reported stigma from the community (38.4%) or who reported stigma toward the child from the spouse (42.9%), family (31.8%) or community (38.1%) were significantly more likely to meet symptom criteria for most mental health disorders. Although not statistically significant, participants who reported acceptance and acceptance of their children from the spouse, family and community were less likely to meet symptom criteria. Women raising children from SVRPs experience symptoms of mental health disorders. Programming addressing stigma and acceptance following sexual violence may improve mental health outcomes in this population. Published by the BMJ Publishing Group

  20. Rethinking exergy efficiency in favor of exergy sustainability as a criteria for design. Paper no. IGEC-1-ID12

    International Nuclear Information System (INIS)

    Seager, T.P.

    2005-01-01

    'Full text:' Engineering design in power generation or conversion has typically focused on minimizing exergy losses (entropy gains), or maximizing economic returns. Both entropy minimization and profit maximization are readily obtainable and acceptable objective criteria for design of thermodynamic processes. However, alternative criteria are imaginable. This research presents a framework for considering minimal environmental impact or maximum renewability as alternative design criteria. In the environmental case, fuel source is based upon an exergetic environmental metric called pollution potential. In the case of renewability, a life-cycle metric describing the replacement time frame of the fuel source is employed. When coupled, the two metrics together partially assess the overall sustainability of the design. (author)

  1. Pressure vessel inspection criteria based on fitness-for-purpose assessment

    International Nuclear Information System (INIS)

    Grover, J.L.; Cipolla, R.C.

    1985-01-01

    The paper on pressure vessel inspection investigates the methodology required to establish an inspection strategy consistent with fracture mechanics analysis, i.e. to define allowable flaw sizes based on location within the vessel. The methodology is demonstrated using a sample problem for a typical pressurised water reactor pressure vessel, and shows the impact of certain assumptions on the inspection strategy. The results indicate that the flaw size varies with the shape of the assumed residual stress field and the through-thickness location. Also in general, the fracture mechanics evaluation allows flaws much larger than are allowed by the inspection acceptance criteria. (UK)

  2. Downstaging therapy followed by liver transplantation for hepatocellular carcinoma beyond Milan criteria.

    Science.gov (United States)

    Kim, Young; Stahl, Christopher C; Makramalla, Abouelmagd; Olowokure, Olugbenga O; Ristagno, Ross L; Dhar, Vikrom K; Schoech, Michael R; Chadalavada, Seetharam; Latif, Tahir; Kharofa, Jordan; Bari, Khurram; Shah, Shimul A

    2017-12-01

    Orthotopic liver transplantation is a curative treatment for hepatocellular carcinoma within Milan criteria, but these criteria preclude many patients from transplant candidacy. Recent studies have demonstrated that downstaging therapy can reduce tumor burden to meet conventional criteria. The present study reports a single-center experience with tumor downstaging and its effects on post-orthotopic liver transplantation outcomes. All patients with hepatocellular carcinoma who were evaluated by our multidisciplinary liver services team from 2012 to 2016 were identified (N = 214). Orthotopic liver transplantation candidates presenting outside of Milan criteria at initial radiographic diagnosis and/or an initial alpha-fetoprotein >400 ng/mL were categorized as at high risk for tumor recurrence and post-transplant mortality. Of the 214 patients newly diagnosed with hepatocellular carcinoma, 73 (34.1%) eventually underwent orthotopic liver transplantation. The majority of patients who did not undergo orthotopic liver transplantation were deceased or lost to follow-up (47.5%), with 14 of 141 (9.9%) currently listed for transplantation. Among transplanted patients, 21 of 73 (28.8%) were considered high-risk candidates. All 21 patients were downstaged to within Milan criteria with an alpha-fetoprotein hepatocellular carcinoma was higher but acceptable between downstaged high-risk and traditional candidates (9.5% vs 1.9%; P > .05) at a median follow-up period of 17 months. Downstaged high-risk candidates had a similar overall survival compared with those transplanted within Milan criteria (log-rank P > .05). In highly selected cases, patients with hepatocellular carcinoma outside of traditional criteria for orthotopic liver transplantation may undergo downstaging therapy in a multidisciplinary fashion with excellent post-transplant outcomes. These data support an aggressive downstaging approach for selected patients who would otherwise be deemed ineligible for

  3. Enhancement of as-sputtered silver-tantalum oxide thin film coating on biomaterial stainless steel by surface thermal treatment

    Science.gov (United States)

    Alias, Rodianah; Mahmoodian, Reza; Shukor, Mohd Hamdi Abd; Yew, Been Seok; Muhamad, Martini

    2018-04-01

    Stainless steel 316L (SS316L) is extensively used as surgical/clinical tools due to its low carbon content and excellent mechanical characteristic. The fabrication of metal ceramic based on this metallic biomaterial favor its biofunctionality properties. However, instability phase of amorphous thin film lead to degradation, corrosion and oxidation. Thus, thin film coating requires elevated adhesion strength and higher surface hardness to meet clinical tools criteria. In this study, the SS316L was deposited with micron thickness of Ag-TaO thin film by using magnetron sputtering. The microstructure, elemental analysis and phase identification of Ag-TaO thin film were characterized by using FESEM, EDX and XRD, respectively; whereas the micro scratch test and micro hardness test were performed by using Micro Scratch Testing System and Vickers Micro Hardness Tester, respectively. It was found that the coating thin film's adhesion and hardness strength were improved from 672 to 2749 mN and 142 to 158 Hv respectively. It was found that the as-deposited surface were treated at 500 °C of temperatures with 2 °C/min ramping rate enhance 4.1 times of the adhesion strength value. Furthermore, FESEM characterization revealed coarsening structure of the thin film coating which can provide high durability service.

  4. History of Uranium-233(233U)Processing at the Rocky Flats Plant. In support of the RFETS Acceptable Knowledge Program

    International Nuclear Information System (INIS)

    Moment, R.L.; Gibbs, F.E.; Freiboth, C.J.

    1999-01-01

    This report documents the processing of Uranium-233 at the Rocky Flats Plant (Rocky Flats Environmental Technology Site). The information may be used to meet Waste Isolation Pilot Plant (WIPP) Waste Acceptance Criteria (WAC)and for determining potential Uranium-233 content in applicable residue waste streams

  5. Project W-320 acceptance test report for AY-farm electrical distribution

    International Nuclear Information System (INIS)

    Bevins, R.R.

    1998-01-01

    This Acceptance Test Procedure (ATP) has been prepared to demonstrate that the AY-Farm Electrical Distribution System functions as required by the design criteria. This test is divided into three parts to support the planned construction schedule; Section 8 tests Mini-Power Pane AY102-PPI and the EES; Section 9 tests the SSS support systems; Section 10 tests the SSS and the Multi-Pak Group Control Panel. This test does not include the operation of end-use components (loads) supplied from the distribution system. Tests of the end-use components (loads) will be performed by other W-320 ATPs

  6. PZT Thin-Film Micro Probe Device with Dual Top Electrodes

    Science.gov (United States)

    Luo, Chuan

    Lead zirconate titanate (PZT) thin-film actuators have been studied intensively for years because of their potential applications in many fields. In this dissertation, a PZT thin-film micro probe device is designed, fabricated, studied, and proven to be acceptable as an intracochlear acoustic actuator. The micro probe device takes the form of a cantilever with a PZT thin-film diaphragm at the tip of the probe. The tip portion of the probe will be implanted in cochlea later in animal tests to prove its feasibility in hearing rehabilitation. The contribution of the dissertation is three-fold. First, a dual top electrodes design, consisting of a center electrode and an outer electrode, is developed to improve actuation displacement of the PZT thin-film diaphragm. The improvement by the dual top electrodes design is studied via a finite element model. When the dimensions of the dual electrodes are optimized, the displacement of the PZT thin-film diaphragm increases about 30%. A PZT thin-film diaphragm with dual top electrodes is fabricated to prove the concept, and experimental results confirm the predictions from the finite element analyses. Moreover, the dual electrode design can accommodate presence of significant residual stresses in the PZT thin-film diaphragm by changing the phase difference between the two electrodes. Second, a PZT thin-film micro probe device is fabricated and tested. The fabrication process consists of PZT thin-film deposition and deep reactive ion etching (DRIE). The uniqueness of the fabrication process is an automatic dicing mechanism that allows a large number of probes to be released easily from the wafer. Moreover, the fabrication is very efficient, because the DRIE process will form the PZT thin-film diaphragm and the special dicing mechanism simultaneously. After the probes are fabricated, they are tested with various possible implantation depths (i.e., boundary conditions). Experimental results show that future implantation depths

  7. Bridging the Gap between Social Acceptance and Ethical Acceptability

    NARCIS (Netherlands)

    Taebi, B.

    2016-01-01

    New technology brings great benefits, but it can also create new and significant risks. When evaluating those risks in policymaking, there is a tendency to focus on social acceptance. By solely focusing on social acceptance, we could, however, overlook important ethical aspects of technological

  8. Vacuum Acceptance Tests for the UHV Room Temperature Vacuum System of the LHC during LS1

    CERN Document Server

    Cattenoz, G; Bregliozzi, G; Calegari, D; Gallagher, J; Marraffa, A; Chiggiato, P

    2014-01-01

    During the CERN Large Hadron Collider (LHC) first long shut down (LS1), a large number of vacuum tests are carried out on consolidated or newly fabricated devices. In such a way, the vacuum compatibility is assessed before installation in the UHV system of the LHC. According to the equipment’s nature, the vacuum acceptance tests consist in functional checks, leak test, outgassing rate measurements, evaluation of contaminants by Residual Gas Analysis (RGA), pumping speed measurements and qualification of the H2 sticking probability of Non-Evaporable-Getter (NEG) coating. In this paper, the methods used for the tests and the acceptance criteria are described. A summary of the measured vacuum characteristics for the tested components is also given.

  9. Video Game Acceptance: A Meta-Analysis of the Extended Technology Acceptance Model.

    Science.gov (United States)

    Wang, Xiaohui; Goh, Dion Hoe-Lian

    2017-11-01

    The current study systematically reviews and summarizes the existing literature of game acceptance, identifies the core determinants, and evaluates the strength of the relationships in the extended technology acceptance model. Moreover, this study segments video games into two categories: hedonic and utilitarian and examines player acceptance of these two types separately. Through a meta-analysis of 50 articles, we find that perceived ease of use (PEOU), perceived usefulness (PU), and perceived enjoyment (PE) significantly associate with attitude and behavioral intention. PE is the dominant predictor of hedonic game acceptance, while PEOU and PU are the main determinants of utilitarian game acceptance. Furthermore, we find that respondent type and game platform are significant moderators. Findings of this study provide critical insights into the phenomenon of game acceptance and suggest directions for future research.

  10. Criteria for guidance in the safety assessment of nuclear installations in the United Kingdom

    International Nuclear Information System (INIS)

    Gausden, R.; Fryer, D.R.H.

    1977-01-01

    There is an increasing appreciation of the need for a consistent approach to nuclear safety between various groups having an interest in safety and between various types of installation. Licensing for construction and ultimate approval to operate any nuclear installation depend in the United Kingdom upon a searching assessment of the design, construction and operation of the proposed plant. Criteria of the kind discussed in this paper have been used by the Nuclear Installations Inspectorate in this assessment process. From time to time they are subject to comments from other bodies in the U.K. One aim of the criteria is to set out the broad objectives that should be met regarding the magnitude of radiological consequences of accidents or normal operation. In addition, the criteria give guidance on the design philosophy for nuclear safety and the principles of fault evaluation. Criteria must be conceived so that while maintaining safety standards their application does not frustrate design and development. It is also important that undue formalism is not induced in the assessment process at the expense of inhibiting the judgement of safety assessors. A balance must, therefore, be struck between detailed and generalised guidance. It is also accepted that experience in the use and interpretation of criteria will indicate a need for improvement and additions: the criteria are, therefore, regarded as living rather than fixed statements which are expected to develop in response to any need for change in a safe direction that may arise. In developing them, the Inspectorate has drawn heavily upon the experience accumulated during its 16 years of operation and has also referred to criteria published by other organisations. The paper deals specifically with certain of the most important sections of the criteria and indicates the total range of subjects which need to be included in such criteria

  11. Combining the IADPSG criteria with the WHO diagnostic criteria for ...

    African Journals Online (AJOL)

    Macrosomia or at least one adverse outcome were more likely in GDM patients who met the diagnostic criteria by both the IADPSG and WHO criteria (P = 0.001). Conclusion: A diagnosis of GDM that meets both the WHO and IADPSG criteria provides stronger prediction for adverse pregnancy outcome than a diagnosis that ...

  12. Adhesive market develops new technologies. The thin-film solar cells gain ground; El mercado de adhesivos desarrolla nuevas tecnologias. Las celulas solares de capa fina ganan terreno

    Energy Technology Data Exchange (ETDEWEB)

    Kluke, M.

    2010-07-01

    The solar industry is booming. thin-film technology is experiencing a high demand as promised cost advantages and currently is providing excellent results, while a range of efficiency reaches acceptable. (Author)

  13. Evaluation models and criteria of the quality of hospital websites: a systematic review study

    OpenAIRE

    Jeddi, Fatemeh Rangraz; Gilasi, Hamidreza; Khademi, Sahar

    2017-01-01

    Introduction Hospital websites are important tools in establishing communication and exchanging information between patients and staff, and thus should enjoy an acceptable level of quality. The aim of this study was to identify proper models and criteria to evaluate the quality of hospital websites. Methods This research was a systematic review study. The international databases such as Science Direct, Google Scholar, PubMed, Proquest, Ovid, Elsevier, Springer, and EBSCO together with regiona...

  14. Neutron absorber qualification and acceptance testing from the designer's perspective

    Energy Technology Data Exchange (ETDEWEB)

    Bracey, W. [Transnuclear, Inc, Hawthorne, NY (United States); Chiocca, R. [Cogema Logistics, St. Quentin en Yvelines (France)

    2004-07-01

    Starting in the mid 1990's, the USNRC began to require less than 100% credit for the 10B present in fixed neutron absorbers spent fuel transport packages. The current practice in the US is to use only 75% of the specified 10B in criticality safety calculations unless extensive acceptance testing demonstrates both the presence of the 10B and uniformity of its distribution. In practice, the NRC has accepted no more than 90% credit for 10B in recent years, while other national competent authorities continue to accept 100%. More recently, with the introduction of new neutron absorber materials, particularly aluminum / boron carbide metal matrix composites, the NRC has also expressed expectations for qualification testing, based in large part on Transnuclear's successful application to use a new composite material in the TN-68 storage / transport cask. The difficulty is that adding more boron than is really necessary to a metal has some negative effects on the material, reducing the ductility and the thermal conductivity, and increasing the cost. Excessive testing requirements can have the undesired effect of keeping superior materials out of spent fuel package designs, without a corresponding justification based on public safety. In European countries and especially in France, 100% credit has been accepted up to now with materials controls specified in the Safety Analysis Report (SAR): Manufacturing process approved by qualification testing Materials manufacturing controlled under a Quality Assurance system. During fabrication, acceptance testing directly on products or on representative samples. Acceptance criteria taking into account a statistical uncertainty corresponding to 3{sigma}. The original and current bases for the reduced {sup 10}B credit, the design requirements for neutron absorber materials, and the experience of Transnuclear and Cogema Logistics with neutron absorber testing are examined. Guidelines for qualification and acceptance testing and

  15. Validation of proposed diagnostic criteria (the "Budapest Criteria") for Complex Regional Pain Syndrome.

    Science.gov (United States)

    Harden, R Norman; Bruehl, Stephen; Perez, Roberto S G M; Birklein, Frank; Marinus, Johan; Maihofner, Christian; Lubenow, Timothy; Buvanendran, Asokumar; Mackey, Sean; Graciosa, Joseph; Mogilevski, Mila; Ramsden, Christopher; Chont, Melissa; Vatine, Jean-Jacques

    2010-08-01

    Current IASP diagnostic criteria for CRPS have low specificity, potentially leading to overdiagnosis. This validation study compared current IASP diagnostic criteria for CRPS to proposed new diagnostic criteria (the "Budapest Criteria") regarding diagnostic accuracy. Structured evaluations of CRPS-related signs and symptoms were conducted in 113 CRPS-I and 47 non-CRPS neuropathic pain patients. Discriminating between diagnostic groups based on presence of signs or symptoms meeting IASP criteria showed high diagnostic sensitivity (1.00), but poor specificity (0.41), replicating prior work. In comparison, the Budapest clinical criteria retained the exceptional sensitivity of the IASP criteria (0.99), but greatly improved upon the specificity (0.68). As designed, the Budapest research criteria resulted in the highest specificity (0.79), again replicating prior work. Analyses indicated that inclusion of four distinct CRPS components in the Budapest Criteria contributed to enhanced specificity. Overall, results corroborate the validity of the Budapest Criteria and suggest they improve upon existing IASP diagnostic criteria for CRPS. Copyright (c) 2010 International Association for the Study of Pain. Published by Elsevier B.V. All rights reserved.

  16. Consumer acceptance of insect-based foods in the Netherlands: Academic and commercial implications.

    Science.gov (United States)

    House, Jonas

    2016-12-01

    Despite growing interest in the use of insects as food, uptake of insect-based foods in Europe is low. Existing research into Western consumer acceptance of insects as food tends to emphasise the role of individual cognition in food choice at the expense of social or contextual factors, and typically frames consumer acceptance as a general issue, rather than relevant only for relatively few early adopters. This paper outlines empirical work, theoretically and methodologically informed by a critical appraisal of previous research, with consumers of insect-based convenience foods in the Netherlands. Reported initial motivations for trying insect foods are shown to be substantially different from factors - such as price, taste, availability, and 'fit' with established eating practices - which affect repeat consumption. Such factors are congruent with those affecting routine consumption of more conventional foods, indicating that insect foods should be analysed according to similar criteria and should be designed with more practical considerations in mind. Further, a reorientation of consumer acceptance research is proposed. Research should shift from attempts to forecast acceptance and engage with 'actual' examples of insect consumption; social, practical and contextual factors affecting food consumption should be emphasised; and - following work on the establishment of other novel foods - early adopters, rather than general populations, should receive greater analytic attention. Copyright © 2016 The Author(s). Published by Elsevier Ltd.. All rights reserved.

  17. Conservatism of present plugging criteria on steam generator tubes and coalescence model of collinear through-wall axial cracks

    International Nuclear Information System (INIS)

    Lee, Jin Ho; Park, Youn Won; Song, Myung Ho; Kim, Young Jin; Moon, Seong In

    1999-01-01

    The steam generator tubing covers a major portion of the primary pressure-retaining boundary, so that very conservative approaches were taken in the light of steam generator tube integrity. According to the present criteria, tubes wall-thinned in excess of 40% should be plugged whatever the cause was. However, it is reported that there is no safety problem even with thickness reductions greater than 40%. Recently, the plant specific plugging criteria are introduced in many countries by demonstrating that the cracked tube has a sufficient safety margin. One of the drawbacks of such criteria, even though not yet codified, is that it is developed based on tubes with single cracks regardless of the fact that the appearance of multiple cracks is general. Their failure analyses have been, therefore, carried out using an idealized single crack to reduce complexity till now. The objective of this paper is to review the conservatism of the present plugging criteria of steam generator tubes and to propose a new coalescence criterion for twin through-wall cracks existing in steam generator tubes. Using the existing failure models and experimental results, we review the conservatism of the present plugging criteria. In order to verify the usefulness of the proposed new coalescence criterion, we perform finite element analysis

  18. A new approach to criteria for health risk assessment

    International Nuclear Information System (INIS)

    Spickett, Jeffery; Katscherian, Dianne; Goh, Yang Miang

    2012-01-01

    Health Impact Assessment (HIA) is a developing component of the overall impact assessment process and as such needs access to procedures that can enable more consistent approaches to the stepwise process that is now generally accepted in both EIA and HIA. The guidelines developed during this project provide a structured process, based on risk assessment procedures which use consequences and likelihood, as a way of ranking risks to adverse health outcomes from activities subjected to HIA or HIA as part of EIA. The aim is to assess the potential for both acute and chronic health outcomes. The consequences component also identifies a series of consequences for the health care system, depicted as expressions of financial expenditure and the capacity of the health system. These more specific health risk assessment characteristics should provide for a broader consideration of health consequences and a more consistent estimation of the adverse health risks of a proposed development at both the scoping and risk assessment stages of the HIA process. - Highlights: ► A more objective approach to health risk assessment is provided. ► An objective set of criteria for the consequences for chronic and acute impacts. ► An objective set of criteria for the consequences on the health care system. ► An objective set of criteria for event frequency that could impact on health. ► The approach presented is currently being trialled in Australia.

  19. An analysis of the qualification criteria for small radioactive material shipping packages

    International Nuclear Information System (INIS)

    McClure, J.D.

    1983-05-01

    The RAM package design certification process has two important elements, testing and acceptance. These terms sound very similar but they have specific meanings. Qualification testing in the context of this study is the imposition of simulated accident test conditions upon the candidate package design. (Normal transportation environments may also be included.) Following qualification testing, the acceptance criteria provide the performance levels which, if demonstrated, indicate the ability of the RAM package to sustain the severity of the qualification testing sequence and yet maintain specified levels of package integrity. This study has used Severities of Transportation Accidents as a data base to examine the regulatory test criteria which are required to be met by small packages containing Type B quantities of radioactive material (RAM). The basic findings indicate that the present regulatory test standards provide significantly higher levels of protection for the surface transportation modes (truck, rail) than for RAM packages shipped by aircraft. It should also be noted that various risk assessment studies have shown that the risk to the public due to severe transport accidents by surface and air transport modes is very low. A key element in this study was the quantification of the severity of the transportation accident environment and the severity of the present qualification test standards (called qualification test standards in this document) so that a direct comparison could be made between them to assess the effectiveness of the existing qualification test standards. The manner in which this was accomplished is described

  20. An analysis of the qualification criteria for small radioactive material shipping packages

    Energy Technology Data Exchange (ETDEWEB)

    McClure, J.D.

    1983-05-01

    The RAM package design certification process has two important elements, testing and acceptance. These terms sound very similar but they have specific meanings. Qualification testing in the context of this study is the imposition of simulated accident test conditions upon the candidate package design. (Normal transportation environments may also be included.) Following qualification testing, the acceptance criteria provide the performance levels which, if demonstrated, indicate the ability of the RAM package to sustain the severity of the qualification testing sequence and yet maintain specified levels of package integrity. This study has used Severities of Transportation Accidents as a data base to examine the regulatory test criteria which are required to be met by small packages containing Type B quantities of radioactive material (RAM). The basic findings indicate that the present regulatory test standards provide significantly higher levels of protection for the surface transportation modes (truck, rail) than for RAM packages shipped by aircraft. It should also be noted that various risk assessment studies have shown that the risk to the public due to severe transport accidents by surface and air transport modes is very low. A key element in this study was the quantification of the severity of the transportation accident environment and the severity of the present qualification test standards (called qualification test standards in this document) so that a direct comparison could be made between them to assess the effectiveness of the existing qualification test standards. The manner in which this was accomplished is described.

  1. In acceptance we trust? Conceptualising acceptance as a viable approach to NGO security management.

    Science.gov (United States)

    Fast, Larissa A; Freeman, C Faith; O'Neill, Michael; Rowley, Elizabeth

    2013-04-01

    This paper documents current understanding of acceptance as a security management approach and explores issues and challenges non-governmental organisations (NGOs) confront when implementing an acceptance approach to security management. It argues that the failure of organisations to systematise and clearly articulate acceptance as a distinct security management approach and a lack of organisational policies and procedures concerning acceptance hinder its efficacy as a security management approach. The paper identifies key and cross-cutting components of acceptance that are critical to its effective implementation in order to advance a comprehensive and systematic concept of acceptance. The key components of acceptance illustrate how organisational and staff functions affect positively or negatively an organisation's acceptance, and include: an organisation's principles and mission, communications, negotiation, programming, relationships and networks, stakeholder and context analysis, staffing, and image. The paper contends that acceptance is linked not only to good programming, but also to overall organisational management and structures. © 2013 The Author(s). Journal compilation © Overseas Development Institute, 2013.

  2. Site selection and rating process, and criteria for a social and political approach

    International Nuclear Information System (INIS)

    Boisseson, P. de; David, J.F.

    1998-01-01

    Full text of publication follows: sensitive projects have been for long the problem of engineers and geologists, which tried to exert a kind of mono-cultural approach upon decisions regarding: a type of technical solution, a choice for a location. Experience drawn from various projects shows that public choices must be targeted to public acceptance and not only to hard-science community. Ways of rating site for sensitive projects according to criteria derived from social and political approach have been set up to provide global advice to decision makers. Bases are found among: socio economical statistics (type and rate of employment), land use regulations, history of public and local acceptance of former projects or public regulations. Representations can be drawn through social modeling and qualitative analysis. They can be of an utmost importance in decision making process. (authors)

  3. Seismic design criteria used for electrical raceway systems in commercial nuclear power plants

    International Nuclear Information System (INIS)

    Summers, P.B.; Manrique, M.A.; Nelson, T.A.

    1991-01-01

    This paper summarizes some of the seismic design approaches, relevant technical issues and criteria used over the years for design of electrical raceway systems at commercial nuclear power plant facilities. The approaches used for design and endorsed by the NRC can be seen to be quite varied. In recent years, considerably more rigor has been required for raceway design, as well as for the level of design basis documentation produced. However, there has also been a willingness by the NRC to accept rational approaches based on testing, analytical results or experience data, provided proper justification is given. Such rational approaches can simplify the significant task of analysis, design and construction of miles of raceways and thousands of raceway supports. Summarizing past practice and identifying relevant technical issues are an important first step in formalizing up-to-date criteria for new raceway designs

  4. NWTS program criteria for mined geologic disposal of nuclear wasite: site performance criteria

    International Nuclear Information System (INIS)

    1981-02-01

    This report states ten criteria governing the suitability of sites for mined geologic disposal of high-level radioactive waste. The Department of Energy will use these criteria in its search for sites and will reevaluate their use when the Nuclear Regulatory Commission issues radioactive waste repository rules. These criteria encompass site geometry, geohydrology, geochemistry, geologic characteristics, tectonic environment, human intrusion, surface characteristics, environment, and potential socioeconomic impacts. The contents of this document include background discussion, site performance criteria, and appendices. The background section describes the waste disposal system, the application of the site criteria, and applicable criteria from NWTS-33(1) - Program Objectives, Functional Requirements and System Performance Criteria. Appendix A, entitled Comparison with Other Siting Criteria compares the NWTS criteria with those recommended by other agencies. Appendix B contains DOE responses to public comments received on the January 1980 draft of this document. Appendix C is a glossary

  5. Thin-film photovoltaic technology

    Energy Technology Data Exchange (ETDEWEB)

    Bhattacharya, R.N. [National Renewable Energy Laboratory, Golden, CO (United States)

    2010-07-01

    The high material and processing costs associated with single-crystal and polycrystalline silicon wafers that are commonly used in photovoltaic cells render these modules expensive. This presentation described thin-film solar cell technology as a promising alternative to silicon solar cell technology. Cadmium telluride (CdTe) thin films along with copper, indium, gallium, and selenium (CIGS) thin films have become the leaders in this field. Their large optical absorption coefficient can be attributed to a direct energy gap that allows the use of thin layers (1-2 {mu}m) of active material. The efficiency of thin-film solar cell devices based on CIGS is 20 per cent, compared to 16.7 per cent for thin-film solar cell devices based on CdTe. IBM recently reported an efficiency of 9.7 per cent for a new type of inorganic thin-film solar cell based on a Cu{sub 2}ZnSn(S, Se){sub 4} compound. The efficiency of an organic thin-film solar cell is 7.9 per cent. This presentation included a graph of PV device efficiencies and discussed technological advances in non-vacuum deposited, CIGS-based thin-film solar cells. 1 fig.

  6. Bioethics and conflicting ethical criteria.

    Science.gov (United States)

    George, Michael

    2002-01-01

    Some of the major problematic issues in contemporary ethical discourse are highlighted in the field of bioethics. The need to incorporate new understandings and foundational shifts in essential criteria because of technological advances in the areas of medicine and human sciences increasingly challenges traditional and accepted notions of ethics. As the possibilities of technical progress increase, more and more pressure is put on traditional understandings of the human person, identity, and value. In the face of ethical relativism and emotivism, which are already widespread in social and political discourse, the immediacy of bioethics as a response to technology and its impact on human lives reinforces the need for ethics to become interdisciplinary, while attempting to provide some coherence to both the questions and the responses that contemporary life generates. In this paper, the author intends to sketch the outlines of some of these problems, and suggest one approach which might allow a certain methodical intelligibility to emerge which takes into account shifts in consciousness and the dependence on historically grounded perspective.

  7. Perspectives on the revised Ghent criteria for the diagnosis of Marfan syndrome

    Science.gov (United States)

    von Kodolitsch, Yskert; De Backer, Julie; Schüler, Helke; Bannas, Peter; Behzadi, Cyrus; Bernhardt, Alexander M; Hillebrand, Mathias; Fuisting, Bettina; Sheikhzadeh, Sara; Rybczynski, Meike; Kölbel, Tilo; Püschel, Klaus; Blankenberg, Stefan; Robinson, Peter N

    2015-01-01

    Three international nosologies have been proposed for the diagnosis of Marfan syndrome (MFS): the Berlin nosology in 1988; the Ghent nosology in 1996 (Ghent-1); and the revised Ghent nosology in 2010 (Ghent-2). We reviewed the literature and discussed the challenges and concepts of diagnosing MFS in adults. Ghent-1 proposed more stringent clinical criteria, which led to the confirmation of MFS in only 32%–53% of patients formerly diagnosed with MFS according to the Berlin nosology. Conversely, both the Ghent-1 and Ghent-2 nosologies diagnosed MFS, and both yielded similar frequencies of MFS in persons with a causative FBN1 mutation (90% for Ghent-1 versus 92% for Ghent-2) and in persons not having a causative FBN1 mutation (15% versus 13%). Quality criteria for diagnostic methods include objectivity, reliability, and validity. However, the nosology-based diagnosis of MFS lacks a diagnostic reference standard and, hence, quality criteria such as sensitivity, specificity, or accuracy cannot be assessed. Medical utility of diagnosis implies congruency with the historical criteria of MFS, as well as with information about the etiology, pathogenesis, diagnostic triggers, prognostic triggers, and potential complications of MFS. In addition, social and psychological utilities of diagnostic criteria include acceptance by patients, patient organizations, clinicians and scientists, practicability, costs, and the reduction of anxiety. Since the utility of a diagnosis or exclusion of MFS is context-dependent, prioritization of utilities is a strategic decision in the process of nosology development. Screening tests for MFS should be used to identify persons with MFS. To confirm the diagnosis of MFS, Ghent-1 and Ghent-2 perform similarly, but Ghent-2 is easier to use. To maximize the utility of the diagnostic criteria of MFS, a fair and transparent process of nosology development is essential. PMID:26124674

  8. A multi-criteria decision making approach to identify a vaccine formulation.

    Science.gov (United States)

    Dewé, Walthère; Durand, Christelle; Marion, Sandie; Oostvogels, Lidia; Devaster, Jeanne-Marie; Fourneau, Marc

    2016-01-01

    This article illustrates the use of a multi-criteria decision making approach, based on desirability functions, to identify an appropriate adjuvant composition for an influenza vaccine to be used in elderly. The proposed adjuvant system contained two main elements: monophosphoryl lipid and α-tocopherol with squalene in an oil/water emulsion. The objective was to elicit a stronger immune response while maintaining an acceptable reactogenicity and safety profile. The study design, the statistical models, the choice of the desirability functions, the computation of the overall desirability index, and the assessment of the robustness of the ranking are all detailed in this manuscript.

  9. Objective CT criteria to determine the presence of abnormal basal enhancement in children with suspected tuberculous meningitis

    International Nuclear Information System (INIS)

    Przybojewski, Stefan; Andronikou, Savvas; Wilmshurst, Jo

    2006-01-01

    There are no widely accepted objective criteria to determine the presence of basal enhancement on CT in children with suspected tuberculous meningitis (TBM). To test nine recently described objective CT criteria for the presence of abnormal basal enhancement in children with suspected TBM against the definite diagnosis as determined by cerebrospinal fluid (CSF) culture. CT scans of patients with a clinical suspicion of TBM who had undergone lumbar puncture for CSF culture spanning a period of 4 years were reviewed for the presence of nine recently described criteria for the presence of abnormal basal enhancement. The radiologists were blinded to the final diagnosis based on CSF culture against which the criteria were tested. The criteria have been named: the 'Y-sign', 'linear enhancement', 'double lines', 'infundibular recess of the third', 'ill-defined edge', 'nodular enhancement', 'join the dots', 'contrast filling the cisterns', and 'asymmetry'. A total of 65 patients were included in the study, 34 with culture-proven TBM and 31 with other diagnoses. Four individual criteria had a specificity of 100%, but the sensitivities of these criteria ranged from 15% to 53% only. Three other criteria had specificities of 97% and sensitivities ranging from 62% to 82%. The presence of more than one criterion in the same patient showed a specificity of 97% and sensitivity of 91%. Very high specificity was demonstrated for all nine criteria, including 100% specificity for four individual criteria. Sensitivity was at best 82%, but improved to 91% when more than one criterion was present. These criteria need to be tested for inter- and intraobserver variability to prove their clinical usefulness. (orig.)

  10. Toward criteria for pragmatic measurement in implementation research and practice: a stakeholder-driven approach using concept mapping.

    Science.gov (United States)

    Powell, Byron J; Stanick, Cameo F; Halko, Heather M; Dorsey, Caitlin N; Weiner, Bryan J; Barwick, Melanie A; Damschroder, Laura J; Wensing, Michel; Wolfenden, Luke; Lewis, Cara C

    2017-10-03

    Advancing implementation research and practice requires valid and reliable measures of implementation determinants, mechanisms, processes, strategies, and outcomes. However, researchers and implementation stakeholders are unlikely to use measures if they are not also pragmatic. The purpose of this study was to establish a stakeholder-driven conceptualization of the domains that comprise the pragmatic measure construct. It built upon a systematic review of the literature and semi-structured stakeholder interviews that generated 47 criteria for pragmatic measures, and aimed to further refine that set of criteria by identifying conceptually distinct categories of the pragmatic measure construct and providing quantitative ratings of the criteria's clarity and importance. Twenty-four stakeholders with expertise in implementation practice completed a concept mapping activity wherein they organized the initial list of 47 criteria into conceptually distinct categories and rated their clarity and importance. Multidimensional scaling, hierarchical cluster analysis, and descriptive statistics were used to analyze the data. The 47 criteria were meaningfully grouped into four distinct categories: (1) acceptable, (2) compatible, (3) easy, and (4) useful. Average ratings of clarity and importance at the category and individual criteria level will be presented. This study advances the field of implementation science and practice by providing clear and conceptually distinct domains of the pragmatic measure construct. Next steps will include a Delphi process to develop consensus on the most important criteria and the development of quantifiable pragmatic rating criteria that can be used to assess measures.

  11. Scaling issues in multi-criteria evaluation of combinations of measures for integrated river basin management

    Science.gov (United States)

    Dietrich, Jörg

    2016-05-01

    In integrated river basin management, measures for reaching the environmental objectives can be evaluated at different scales, and according to multiple criteria of different nature (e.g. ecological, economic, social). Decision makers, including responsible authorities and stakeholders, follow different interests regarding criteria and scales. With a bottom up approach, the multi criteria assessment could produce a different outcome than with a top down approach. The first assigns more power to the local community, which is a common principle of IWRM. On the other hand, the development of an overall catchment strategy could potentially make use of synergetic effects of the measures, which fulfils the cost efficiency requirement at the basin scale but compromises local interests. Within a joint research project for the 5500 km2 Werra river basin in central Germany, measures have been planned to reach environmental objectives of the European Water Framework directive (WFD) regarding ecological continuity and nutrient loads. The main criteria for the evaluation of the measures were costs of implementation, reduction of nutrients, ecological benefit and social acceptance. The multi-criteria evaluation of the catchment strategies showed compensation between positive and negative performance of criteria within the catchment, which in the end reduced the discriminative power of the different strategies. Furthermore, benefit criteria are partially computed for the whole basin only. Both ecological continuity and nutrient load show upstream-downstream effects in opposite direction. The principles of "polluter pays" and "overall cost efficiency" can be followed for the reduction of nutrient losses when financial compensations between upstream and downstream users are made, similar to concepts of emission trading.

  12. Solid thin film materials for use in thin film charge-coupled devices

    International Nuclear Information System (INIS)

    Lynch, S.J.

    1983-01-01

    Solid thin films deposited by vacuum deposition were evaluated to ascertain their effectiveness for use in the manufacturing of charge-coupled devices (CCDs). Optical and electrical characteristics of tellurium and Bi 2 Te 3 solid thin films were obtained in order to design and to simulate successfully the operation of thin film (TF) CCDs. In this article some of the material differences between single-crystal material and the island-structured thin film used in TFCCDs are discussed. The electrical parameters were obtained and tabulated, e.g. the mobility, conductivity, dielectric constants, permittivity, lifetime of holes and electrons in the thin films and drift diffusion constants. The optical parameters were also measured and analyzed. After the design was complete, experimental TFCCDs were manufactured and were successfully operated utilizing the aforementioned solid thin films. (Auth.)

  13. Criteria for design of the Yucca Mountain structures, systems and components for fault displacement

    International Nuclear Information System (INIS)

    Stepp, C.; Hossain, Q.; Nesbit, S.; Pezzopane, S.; Hardy, M.

    1995-01-01

    The DOE intends to design the Yucca Mountain high-level waste facility structures, systems and components (SSCs) for fault displacements to provide reasonable assurance that they will meet the preclosure safety performance objectives established by 10 CFR Part 60. To the extent achievable, fault displacement design of the facility will follow guidance provided in the NRC Staff Technical Position. Fault avoidance will be the primary design criterion, especially for spatially compact or clustered SSCs. When fault avoidance is not reasonably achievable, expected to be the case for most spatially extended SSCs, engineering design procedures and criteria or repair and rehabilitation actions, depending on the SSC's importance to safety, are provided. SSCs that have radiological safety importance will be designed for fault displacements that correspond to the hazard exceedance frequency equal to their established seismic safety performance goals. Fault displacement loads are generally localized and may cause local inelastic response of SSCs. For this reason, the DOE intends to use strain-based design acceptance criteria similar to the strain-based criteria used to design nuclear plant SSCs for impact and impulsive loads

  14. Should repository release criteria be based on collective dose, release limits, or individual doses?

    International Nuclear Information System (INIS)

    Channell, J.K.; Neill, R.H.

    1999-01-01

    The advantages and disadvantages of using each of 3 alternative methods (collective dose, release limits, and individual dose) as release criteria for determining long-term high level or transuranic waste repository performance of naturally occurring releases or man-made intrusions are evaluated. Each of the alternative approaches have positive aspects and each has uncertainties that require some arbitrary assumptions. A comparison of the numerical results from evaluating the three alternatives at WIPP leads to the conclusion that a collective dose is preferable because it is more site specific and allows consideration of the full effects of human intrusion. The main objection to release limits is they do not use site specific criteria to determine the radiological effect on local and regional populations. Individual dose criteria used and recommended in the United States have ignored doses to drillers and the public from wastes brought to the surface by human intrusion because these doses can be greater than acceptable limits. Also, there is disagreement about defining the location and lifestyle of the individual

  15. Nuclear energy socially acceptable as a possible solution for the Brazilian energy demand

    International Nuclear Information System (INIS)

    Milanez, Jimes Vasco; Almeida, Ricardo Dias; Carmo, Fausto Silva do

    2006-01-01

    In this work we try to investigate the potential, with emphasis on Brazil, of new nuclear power technologies in development related to estimated growth of energy demand in comparison to traditional nuclear power and others alternatives generation, under criteria such as technical and economic viability, respect to the environmental and particularly acceptability of the society. It is demonstrated that fourth generation of nuclear power shows an option to be considered in the medium and long-term for energy generation significantly clean, efficient and safe, should be, therefore, better investigated, mainly focusing on accelerator driven systems

  16. Formulation of criteria for pollution control on cement products produced from solid wastes in China.

    Science.gov (United States)

    Yang, Yufei; Huang, Qifei; Yang, Yu; Huang, Zechun; Wang, Qi

    2011-08-01

    The process of producing cement products from solid waste can increase the level of pollutants in the cement products. Therefore, it is very important to establish a pollution control standard for cement products to protect the environment and human health. This paper presents acceptance limits for the availability of heavy metals in cement products which have been produced from solid wastes and explains how the limits have been calculated. The approach and method used to formulate these criteria were based on EN 12920. The typical exposure scenarios used in this paper involve concrete being used for drinking water supply pipelines and concrete pavements and are based on an analysis of typical applications of cement in China, and the potential for contact with water. The parameters of a tank test which was based on NEN 7375 were set in accordance with the environmental conditions of typical scenarios in China. Mechanisms controlling the release of heavy metals in concrete and a model for that release were obtained using the leaching test. Finally, based on acceptance criteria for drinking water and groundwater quality in China, limit values for the availability of heavy metals in concrete were calculated. Copyright © 2011 Elsevier Ltd. All rights reserved.

  17. Consumer acceptance of and willingness to pay for food nanotechnology: a systematic review

    International Nuclear Information System (INIS)

    Giles, Emma L.; Kuznesof, Sharron; Clark, Beth; Hubbard, Carmen; Frewer, Lynn J.

    2015-01-01

    Consumer’s attitudes to, and acceptance of, emerging technologies and their applications, are important determinants of their successful implementation and commercialisation. Understanding the range of socio-psychological, cultural and affective factors which may influence consumer responses to applications of nanotechnology will help “fine-tune” the development of consumer products in line with their expectations and preferences. This is particularly true of applications in the food area, where consumer concerns about technologies applied to food production may be elevated. This research applied systematic review methodology to synthesise current knowledge regarding societal acceptance or rejection of nanotechnology applied to agri-food production. The objective was to aggregate knowledge derived from different research areas to gain an overall picture of consumer responses to nanotechnology applied to food production. Relevant electronic databases of peer-reviewed literature were searched from the earliest date available, for peer-reviewed papers which reported primary empirical data on consumer and expert acceptance of agri-food nanotechnology, using a formal systematic review protocol. Inclusion criteria for papers to be included in the review were: empirical peer-reviewed papers written in English; a population sample of adults aged 18 years and over used in the research; a research focus on consumer and expert acceptance of agri-food nanotechnology; and research on attitudes towards, and willingness to pay for, different applications of agri-food nanotechnology. Two researchers independently appraised the papers using NVivo 10 QSR software. Studies examining consumer and expert acceptance were thematically analysed, and key information was collated. The results were synthesised in order to identify trends in information relevant to consumer acceptance of nanotechnology applied to food production. Eight key themes were identified from the 32 papers

  18. Consumer acceptance of and willingness to pay for food nanotechnology: a systematic review.

    Science.gov (United States)

    Giles, Emma L; Kuznesof, Sharron; Clark, Beth; Hubbard, Carmen; Frewer, Lynn J

    Consumer's attitudes to, and acceptance of, emerging technologies and their applications, are important determinants of their successful implementation and commercialisation. Understanding the range of socio-psychological, cultural and affective factors which may influence consumer responses to applications of nanotechnology will help "fine-tune" the development of consumer products in line with their expectations and preferences. This is particularly true of applications in the food area, where consumer concerns about technologies applied to food production may be elevated. This research applied systematic review methodology to synthesise current knowledge regarding societal acceptance or rejection of nanotechnology applied to agri-food production. The objective was to aggregate knowledge derived from different research areas to gain an overall picture of consumer responses to nanotechnology applied to food production. Relevant electronic databases of peer-reviewed literature were searched from the earliest date available, for peer-reviewed papers which reported primary empirical data on consumer and expert acceptance of agri-food nanotechnology, using a formal systematic review protocol. Inclusion criteria for papers to be included in the review were: empirical peer-reviewed papers written in English; a population sample of adults aged 18 years and over used in the research; a research focus on consumer and expert acceptance of agri-food nanotechnology; and research on attitudes towards, and willingness to pay for, different applications of agri-food nanotechnology. Two researchers independently appraised the papers using NVivo 10 QSR software. Studies examining consumer and expert acceptance were thematically analysed, and key information was collated. The results were synthesised in order to identify trends in information relevant to consumer acceptance of nanotechnology applied to food production. Eight key themes were identified from the 32 papers which were

  19. Consumer acceptance of and willingness to pay for food nanotechnology: a systematic review

    Energy Technology Data Exchange (ETDEWEB)

    Giles, Emma L., E-mail: e.giles@tees.ac.uk [Teesside University, Health and Social Care Institute (United Kingdom); Kuznesof, Sharron; Clark, Beth; Hubbard, Carmen; Frewer, Lynn J. [Newcastle University, School of Agriculture, Food and Rural Development (United Kingdom)

    2015-12-15

    Consumer’s attitudes to, and acceptance of, emerging technologies and their applications, are important determinants of their successful implementation and commercialisation. Understanding the range of socio-psychological, cultural and affective factors which may influence consumer responses to applications of nanotechnology will help “fine-tune” the development of consumer products in line with their expectations and preferences. This is particularly true of applications in the food area, where consumer concerns about technologies applied to food production may be elevated. This research applied systematic review methodology to synthesise current knowledge regarding societal acceptance or rejection of nanotechnology applied to agri-food production. The objective was to aggregate knowledge derived from different research areas to gain an overall picture of consumer responses to nanotechnology applied to food production. Relevant electronic databases of peer-reviewed literature were searched from the earliest date available, for peer-reviewed papers which reported primary empirical data on consumer and expert acceptance of agri-food nanotechnology, using a formal systematic review protocol. Inclusion criteria for papers to be included in the review were: empirical peer-reviewed papers written in English; a population sample of adults aged 18 years and over used in the research; a research focus on consumer and expert acceptance of agri-food nanotechnology; and research on attitudes towards, and willingness to pay for, different applications of agri-food nanotechnology. Two researchers independently appraised the papers using NVivo 10 QSR software. Studies examining consumer and expert acceptance were thematically analysed, and key information was collated. The results were synthesised in order to identify trends in information relevant to consumer acceptance of nanotechnology applied to food production. Eight key themes were identified from the 32 papers

  20. Consumer acceptance of and willingness to pay for food nanotechnology: a systematic review

    Science.gov (United States)

    Giles, Emma L.; Kuznesof, Sharron; Clark, Beth; Hubbard, Carmen; Frewer, Lynn J.

    2015-12-01

    Consumer's attitudes to, and acceptance of, emerging technologies and their applications, are important determinants of their successful implementation and commercialisation. Understanding the range of socio-psychological, cultural and affective factors which may influence consumer responses to applications of nanotechnology will help "fine-tune" the development of consumer products in line with their expectations and preferences. This is particularly true of applications in the food area, where consumer concerns about technologies applied to food production may be elevated. This research applied systematic review methodology to synthesise current knowledge regarding societal acceptance or rejection of nanotechnology applied to agri-food production. The objective was to aggregate knowledge derived from different research areas to gain an overall picture of consumer responses to nanotechnology applied to food production. Relevant electronic databases of peer-reviewed literature were searched from the earliest date available, for peer-reviewed papers which reported primary empirical data on consumer and expert acceptance of agri-food nanotechnology, using a formal systematic review protocol. Inclusion criteria for papers to be included in the review were: empirical peer-reviewed papers written in English; a population sample of adults aged 18 years and over used in the research; a research focus on consumer and expert acceptance of agri-food nanotechnology; and research on attitudes towards, and willingness to pay for, different applications of agri-food nanotechnology. Two researchers independently appraised the papers using NVivo 10 QSR software. Studies examining consumer and expert acceptance were thematically analysed, and key information was collated. The results were synthesised in order to identify trends in information relevant to consumer acceptance of nanotechnology applied to food production. Eight key themes were identified from the 32 papers which were

  1. Multi criteria decision analysis on a waste repository in Mol

    International Nuclear Information System (INIS)

    Carle, B.

    2005-01-01

    In Belgium, the management of radioactive waste is taken care of by ONDRAF/NIRAS, the Belgian Agency for Radioactive Waste and Enriched Fissile Materials. Local partnerships with stakeholders from municipalities in existing nuclear zones were setup to facilitate the dialogue between the repository designers and the local community. Since the establishment of the partnership in Mol, MONA in February 2000, all aspects of a possible near-surface or a deep geological repository are discussed in 4 working groups by around 50 volunteer members. The outcome of the discussions in the partnership can be a shared project, supported by both local stakeholders and ONDRAF/NIRAS, in which the specifications and the conditions needed for establishing a repository in Mol are elaborated. MONA asked the Decision Strategy Research Department of SCK-CEN to organise a Multi Criteria Analysis (MCA) in the context of the deciding between a surface and a deep repository for low level radioactive waste. The objective of the multi criteria analysis is to support a number of representatives of the various working groups within MONA in their selection between two acceptable options for a repository of low level radioactive waste on the territory of Mol. The options are the surface repository developed by the working groups of MONA, and a deep repository in the clay layers underneath the nuclear site of Mol. This study should facilitate the selection between both options, or in case this appears to be difficult, at least to get a well-structured overview of all factors (criteria) of importance to the judgement, and to get insight into the degree in which the various criteria contribute to the selection

  2. MEASUREMENT FOR ACCEPTANCE OF SUPPLY CHAIN SIMULATOR APPLICATION USING TECHNOLOGY ACCEPTANCE MODEL

    Directory of Open Access Journals (Sweden)

    Mulyati E.

    2018-03-01

    Full Text Available The aim of this research for was to measure the user acceptance of simulator application which was built as a tool for student in learning of supply chain, particularly in bullwhip effect problem. The measurements used for the acceptance of supply chain simulator application in this research was the Technology Acceptance Model from 162 samples which were analyzed with Confirmatory Factor Analysis and Structural Equation Modelling. The result of this research indicated that the user acceptance (shown by customer participation of supply chain simulator was directly influence by perceived usefulness of supply chain simulator application used (positive and significant; the user acceptance of supply chain simulator was indirectly influenced by perceived ease of use in using supply chain simulator application (positive but not significant; the user acceptance of supply chain simulator was indirectly influenced by perceived enjoyment when the supply chain simulator application was used. The research would give a better understanding about a bullwhip effect and better experience for students, which would not be obtained through conventional learning, when the tools were not used.

  3. [Acceptance of lot sampling: its applicability to the evaluation of the primary care services portfolio].

    Science.gov (United States)

    López-Picazo Ferrer, J

    2001-05-15

    To determine the applicability of the acceptance of lot quality assurance sampling (LQAS) in the primary care service portfolio, comparing its results with those given by classic evaluation. Compliance with the minimum technical norms (MTN) of the service of diabetic care was evaluated through the classic methodology (confidence 95%, accuracy 5%, representativeness of area, sample of 376 histories) and by LQAS (confidence 95%, power 80%, representativeness of primary care team (PCT), defining a lot by MTN and PCT, sample of 13 histories/PCT). Effort, information obtained and its operative nature were assessed. 44 PCTs from Murcia Primary Care Region. Classic methodology: compliance with MTN ranged between 91.1% (diagnosis, 95% CI, 84.2-94.0) and 30% (repercussion in viscera, 95% CI, 25.4-34.6). Objectives in three MTN were reached (diagnosis, history and EKG). LQAS: no MTN was accepted in all the PCTs, being the most accepted (42 PCT, 95.6%) and the least accepted (24 PCT, 55.6%). In 9 PCT all were accepted (20.4%), and in 2 none were accepted (4.5%). Data were analysed through Pareto charts. Classic methodology offered accurate results, but did not identify which centres were those that did not comply (general focus). LQAS was preferable for evaluating MTN and probably coverage because: 1) it uses small samples, which foment internal quality-improvement initiatives; 2) it is easy and rapid to execute; 3) it identifies the PCT and criteria where there is an opportunity for improvement (specific focus), and 4) it can be used operatively for monitoring.

  4. Planning and acceptance testing of MV therapy installations

    International Nuclear Information System (INIS)

    Almond, Peter R.; Horton, John L.

    1995-01-01

    Purpose: This course is designed for practitioners and beginners in brachytherapy. The aim is to review biological principles equipment are aware of all aspects involved. The object is to cover in a broad overview the considerations that go into selecting, installing, testing and accepting megavoltage therapy equipment and to provide a resource for more detailed information. Planning and acceptance testing of a megavoltage therapy installation is a major undertaking for any size group, institution or department. It can take approximately two years from the time a decision is made to get a machine to where the first patient is treated. Because the equipment and site preparation are expensive, and most of the machines are complex and can be supplied by several different manufacturers, it is imperative that a great deal of thought and care go into the decision: the aim being that the specifications of the machine that is installed meet the immediate need of the department and the needs for the projected lifetime of the equipment. A general survey of the types of equipment available will be presented. This will concentrate on general purpose linear accelerators, although Cobalt 60 machines, microtrons and special purpose machines (intra-operative equipment) will also be covered. General descriptions of the machines along with typical specifications will be given. Selecting the best machine to meet specific needs can be quite complex and criteria for making the selection are presented in a series of twelve steps. site selection and room design, including the console area, are also critical. The general principles for shielding calculations will be provided. Critical to any installation is the acceptance testing of the equipment including material and radiation oncology performance tests. These tests will be outlined. A reading list of suitable references describing in detail many of the aspects of this course will be provided

  5. Assessing Professionalism: A Theoretical Framework for Defining Clinical Rotation Assessment Criteria.

    Science.gov (United States)

    Armitage-Chan, Elizabeth

    Although widely accepted as an important graduate competence, professionalism is a challenging outcome to define and assess. Clinical rotations provide an excellent opportunity to develop student professionalism through the use of experiential learning and effective feedback, but without appropriate theoretical frameworks, clinical teachers may find it difficult to identify appropriate learning outcomes. The adage "I know it when I see it" is unhelpful in providing feedback and guidance for student improvement, and criteria that are more specifically defined would help students direct their own development. This study sought first to identify how clinical faculty in one institution currently assess professionalism, using retrospective analysis of material obtained in undergraduate teaching and faculty development sessions. Subsequently, a faculty workshop was held in which a round-table type discussion sought to develop these ideas and identify how professionalism assessment could be improved. The output of this session was a theoretical framework for teaching and assessing professionalism, providing example assessment criteria and ideas for clinical teaching. This includes categories such as client and colleague interaction, respect and trust, recognition of limitations, and understanding of different professional identities. Each category includes detailed descriptions of the knowledge, skills, and behaviors expected of students in these areas. The criteria were determined by engaging faculty in the development of the framework, and therefore they should represent a focused development of criteria already used to assess professionalism, and not a novel and unfamiliar set of assessment guidelines. The faculty-led nature of this framework is expected to facilitate implementation in clinical teaching.

  6. Readiness to accept Western standard of beauty and body satisfaction among Muslim girls with and without hijab.

    Science.gov (United States)

    Đurović, Dušanka; Tiosavljević, Marija; Šabanović, Harisa

    2016-10-01

    The purpose of this paper was to determine whether there is a difference in the readiness to accept Western standards of beauty in which thinness is an ideal of beauty and attractiveness, as well in body and appearance satisfaction between Muslim adolescent girls attending madrassa and dressing in accordance with tradition, that is to say wearing hijab, and Muslim adolescent girls who do not wear hijab and who follow contemporary Western-influenced fashion trends. Both of these groups were also compared to a non-Muslim group of adolescent girls. The sample consisted of 75 Muslim adolescent girls with hijab, 75 Muslim adolescent girls without hijab and 75 Orthodox adolescent girls. The following instruments were used: the Eating Attitudes Test (EAT-26), the Sociocultural Attitudes towards Appearance Questionnaire (SATAQ-3) and the Contour Drawing Rating Scale (CDRS). The highest level of body satisfaction (despite this group having the highest body weight in the sample) was evident among Muslim adolescent girls attending madrassa and wearing hijab. They also showed significantly less pressure to attain the Western thin-ideal standards of beauty than adolescent girls who accept Western way of dressing. Research results indicate a significant role of socio-cultural factors in one's attitude towards the body image, but also opens the question of the role of religion as a protective factor when it comes to the body and appearance attitude among Muslim women who wear hijab. © 2016 Scandinavian Psychological Associations and John Wiley & Sons Ltd.

  7. Thin film processes II

    CERN Document Server

    Kern, Werner

    1991-01-01

    This sequel to the 1978 classic, Thin Film Processes, gives a clear, practical exposition of important thin film deposition and etching processes that have not yet been adequately reviewed. It discusses selected processes in tutorial overviews with implementation guide lines and an introduction to the literature. Though edited to stand alone, when taken together, Thin Film Processes II and its predecessor present a thorough grounding in modern thin film techniques.Key Features* Provides an all-new sequel to the 1978 classic, Thin Film Processes* Introduces new topics, and sever

  8. Plutonium storage criteria

    Energy Technology Data Exchange (ETDEWEB)

    Chung, D. [Scientech, Inc., Germantown, MD (United States); Ascanio, X. [Dept. of Energy, Germantown, MD (United States)

    1996-05-01

    The Department of Energy has issued a technical standard for long-term (>50 years) storage and will soon issue a criteria document for interim (<20 years) storage of plutonium materials. The long-term technical standard, {open_quotes}Criteria for Safe Storage of Plutonium Metals and Oxides,{close_quotes} addresses the requirements for storing metals and oxides with greater than 50 wt % plutonium. It calls for a standardized package that meets both off-site transportation requirements, as well as remote handling requirements from future storage facilities. The interim criteria document, {open_quotes}Criteria for Interim Safe Storage of Plutonium-Bearing Solid Materials{close_quotes}, addresses requirements for storing materials with less than 50 wt% plutonium. The interim criteria document assumes the materials will be stored on existing sites, and existing facilities and equipment will be used for repackaging to improve the margin of safety.

  9. Super Nonlinear Electrodeposition-Diffusion-Controlled Thin-Film Selector.

    Science.gov (United States)

    Ji, Xinglong; Song, Li; He, Wei; Huang, Kejie; Yan, Zhiyuan; Zhong, Shuai; Zhang, Yishu; Zhao, Rong

    2018-03-28

    Selector elements with high nonlinearity are an indispensable part in constructing high density, large-scale, 3D stackable emerging nonvolatile memory and neuromorphic network. Although significant efforts have been devoted to developing novel thin-film selectors, it remains a great challenge in achieving good switching performance in the selectors to satisfy the stringent electrical criteria of diverse memory elements. In this work, we utilized high-defect-density chalcogenide glass (Ge 2 Sb 2 Te 5 ) in conjunction with high mobility Ag element (Ag-GST) to achieve a super nonlinear selective switching. A novel electrodeposition-diffusion dynamic selector based on Ag-GST exhibits superior selecting performance including excellent nonlinearity (<5 mV/dev), ultra-low leakage (<10 fA), and bidirectional operation. With the solid microstructure evidence and dynamic analyses, we attributed the selective switching to the competition between the electrodeposition and diffusion of Ag atoms in the glassy GST matrix under electric field. A switching model is proposed, and the in-depth understanding of the selective switching mechanism offers an insight of switching dynamics for the electrodeposition-diffusion-controlled thin-film selector. This work opens a new direction of selector designs by combining high mobility elements and high-defect-density chalcogenide glasses, which can be extended to other materials with similar properties.

  10. NWTS program criteria for mined geologic disposal of nuclear waste: functional requirements and performance criteria for waste packages for solidified high-level waste and spent fuel

    International Nuclear Information System (INIS)

    1982-07-01

    The Department of Energy (DOE) has primary federal responsibility for the development and implementation of safe and environmentally acceptable nuclear waste disposal methods. Currently, the principal emphasis in the program is on emplacement of nuclear wastes in mined geologic repositories well beneath the earth's surface. A brief description of the mined geologic disposal system is provided. The National Waste Terminal Storage (NWTS) program was established under DOE's predecessor, the Energy Research and Development Administration, to provide facilities for the mined geologic disposal of radioactive wastes. The NWTS program includes both the development and the implementation of the technology necessary for designing, constructing, licensing, and operating repositories. The program does not include the management of processing radioactive wastes or of transporting the wastes to repositories. The NWTS-33 series, of which this document is a part, provides guidance for the NWTS program in the development and implementation of licensed mined geologic disposal systems for solidified high-level and transuranic (TRU) wastes. This document presents the functional requirements and performance criteria for waste packages for solidified high-level waste and spent fuel. A separate document to be developed, NWTS-33(4b), will present the requirements and criteria for waste packages for TRU wastes. The hierarchy and application of these requirements and criteria are discussed in Section 2.2

  11. Research on probabilistic assessment method based on the corroded pipeline assessment criteria

    International Nuclear Information System (INIS)

    Zhang Guangli; Luo, Jinheng; Zhao Xinwei; Zhang Hua; Zhang Liang; Zhang Yi

    2012-01-01

    Pipeline integrity assessments are performed using conventional deterministic approaches, even though there are many uncertainties about the parameters in the pipeline integrity assessment. In this paper, a probabilistic assessment method is provided for the gas pipeline with corrosion defects based on the current corroded pipe evaluation criteria, and the failure probability of corroded pipelines due to the uncertainties of loadings, material property and measurement accuracy is estimated using Monte-Carlo technique. Furthermore, the sensitivity analysis approach is introduced to rank the influence of various random variables to the safety of pipeline. And the method to determine the critical defect size based on acceptable failure probability is proposed. Highlights: ► The folias factor in pipeline corrosion assessment methods was analyzed. ► The probabilistic method was applied in corrosion assessment methods. ► The influence of assessment variables to the reliability of pipeline was ranked. ► The acceptable failure probability was used to determine the critical defect size.

  12. Multidimensional Diagnostic Criteria for Chronic Pain: Introduction to the ACTTION-American Pain Society Pain Taxonomy (AAPT).

    Science.gov (United States)

    Dworkin, Robert H; Bruehl, Stephen; Fillingim, Roger B; Loeser, John D; Terman, Gregory W; Turk, Dennis C

    2016-09-01

    A variety of approaches have been used to develop diagnostic criteria for chronic pain. The published evidence of the reliability and validity of existing diagnostic criteria is limited, and these criteria have typically not been used in clinical practice. The availability of a widely accepted, consistently applied, and evidence-based taxonomy of diagnostic criteria would improve the quality of clinical research on chronic pain and would be of great value in clinical practice. To address the need for evidence-based diagnostic criteria for the major chronic pain conditions, the Analgesic, Anesthetic, and Addiction Clinical Trial Translations, Innovations, Opportunities, and Networks (ACTTION) public-private partnership with the US Food and Drug Administration and the American Pain Society (APS) have collaborated on the development of the ACTTION-APS Pain Taxonomy (AAPT). AAPT provides a multidimensional framework that is applied systematically in the development of diagnostic criteria. This article (1) describes the background and rationale for AAPT; (2) presents the AAPT taxonomy and the specific conditions for which diagnostic criteria have been developed (to be published separately); (3) briefly reviews the 5 dimensions that constitute the AAPT multidimensional framework and describes the 7 accompanying articles that discuss these dimensions and other important issues involving AAPT; and (4) provides an overview of next steps, specifically, the general processes by which the initial set of diagnostic criteria (for which the evidence base has been drawn from the literature, systematic reviews, and secondary analyses of existing databases) will undergo additional assessments of reliability and validity. To address the need for evidence-based diagnostic criteria for the major chronic pain conditions, the AAPT provides a multidimensional framework that is applied systematically in the development of diagnostic criteria. The long-term objective of AAPT is to advance

  13. Guidelines and algorithms: strategies for standardization of referral criteria in diagnostic radiology

    International Nuclear Information System (INIS)

    Kainberger, Franz; Pokieser, Peter; Imhof, Herwig; Czembirek, Heinrich; Fruehwald, Franz

    2002-01-01

    Guidelines can be regarded as special forms of algorithms and have been shown to be useful tools for supporting medical decision making. With the Council Directive 97/43/Euratom recommendations concerning referral criteria for medical exposure have to be implemented into national law of all EU member states. The time- and cost-consuming efforts of developing, implementing, and updating such guidelines are balanced by the acceptance in clinical practice and eventual better health outcomes. Clearly defined objectives with special attention drawn on national and regional differences among potential users, support from organisations with expertise in evidence-based medicine, separated development of the evidence component and the recommendations component, and large-scale strategies for distribution and implementation are necessary. Editors as well as users of guidelines for referral criteria have to be aware which expectations can be met and which cannot be fulfilled with this instrument; thus, dealing with guidelines requires a new form of ''diagnostic reasoning'' based on medical ethics. (orig.)

  14. Near Net Manufacturing Using Thin Gage Friction Stir Welding

    Science.gov (United States)

    Takeshita, Jennifer; Potter, David; Holquin, Michael

    2006-01-01

    Friction Stir Welding (FSW) and near net spin forming of FSW aluminumn blanks were investigated for large-scale pressure vessel applications. With a specific focus on very thin gage 2xxx and 7xxx aluminum alloys, the program concentrated on the following: the criteria used for material selection, a potential manufacturing flow, and the effectiveness and associated risks of near net spin forming. Discussion will include the mechanical properties of the friction stir welds and the parent material from before and after the spin forming process. This effort was performed under a NASA Space Exploration initiative focused on increasing the affordability, reliability and performance of pressure vessels larger than 10 ft. diameter.

  15. Improved exposure estimation in soil screening and cleanup criteria for volatile organic chemicals.

    Science.gov (United States)

    DeVaull, George E

    2017-09-01

    Soil cleanup criteria define acceptable concentrations of organic chemical constituents for exposed humans. These criteria sum the estimated soil exposure over multiple pathways. Assumptions for ingestion, dermal contact, and dust exposure generally presume a chemical persists in surface soils at a constant concentration level for the entire exposure duration. For volatile chemicals, this is an unrealistic assumption. A calculation method is presented for surficial soil criteria that include volatile depletion of chemical for these uptake pathways. The depletion estimates compare favorably with measured concentration profiles and with field measurements of soil concentration. Corresponding volatilization estimates compare favorably with measured data for a wide range of volatile and semivolatile chemicals, including instances with and without the presence of a mixed-chemical residual phase. Selected examples show application of the revised factors in estimating screening levels for benzene in surficial soils. Integr Environ Assess Manag 2017;13:861-869. © 2017 The Authors. Integrated Environmental Assessment and Management published by Wiley Periodicals, Inc. on behalf of Society of Environmental Toxicology & Chemistry (SETAC). © 2017 The Authors. Integrated Environmental Assessment and Management published by Wiley Periodicals, Inc. on behalf of Society of Environmental Toxicology & Chemistry (SETAC).

  16. A Preliminary Investigation of Acceptance and Commitment Therapy as a Treatment for Marijuana Dependence in Adults

    OpenAIRE

    Twohig, Michael P; Shoenberger, Deacon; Hayes, Steven C

    2007-01-01

    In this investigation, 3 adults who met criteria for marijuana dependence were treated using an abbreviated version of acceptance and commitment therapy (ACT). The treatment was delivered in eight weekly 90-min individual sessions. The effects of the intervention were assessed using a nonconcurrent multiple baseline across participants design. Self-reported marijuana use, confirmed through oral swabs, reached zero levels for all participants at posttreatment. At a 3-month follow-up, 1 partici...

  17. The Insulation for Machines Having a High Lifespan Expectancy, Design, Tests and Acceptance Criteria Issues

    Directory of Open Access Journals (Sweden)

    Olivier Barré

    2017-02-01

    Full Text Available The windings insulation of electrical machines will remain a topic that is updated frequently. The criteria severity requested by the electrical machine applications increases continuously. Manufacturers and designers are always confronted with new requirements or new criteria with enhanced performances. The most problematic requirements that will be investigated here are the extremely long lifespan coupled to critical operating conditions (overload, supply grid instabilities, and critical operating environments. Increasing lifespan does not have a considerable benefit because the purchasing price of usual machines has to be compared to the purchasing price and maintenance price of long lifespan machines. A machine having a 40-year lifespan will cost more than twice the usual price of a 20-year lifetime machine. Systems which need a long lifetime are systems which are crucial for a country, and those for which outage costs are exorbitant. Nuclear power stations are such systems. It is certain that the used technologies have evolved since the first nuclear power plant, but they cannot evolve as quickly as in other sectors of activities. No-one wants to use an immature technology in such power plants. Even if the electrical machines have exceeded 100 years of age, their improvements are linked to a patient and continuous work. Nowadays, the windings insulation systems have a well-established structure, especially high voltage windings. Unfortunately, a high life span is not only linked to this result. Several manufacturers’ improvements induced by many years of experiment have led to the writing of standards that help the customers and the manufacturers to regularly enhance the insulation specifications or qualifications. Hence, in this publication, the authors will give a step by step exhaustive review of one insulation layout and will take time to give a detailed report on the standards that are linked to insulation systems. No standard can

  18. Fruit self-thinning: a trait to consider for genetic improvement of apple tree.

    Science.gov (United States)

    Celton, Jean-Marc; Kelner, Jean-Jacques; Martinez, Sébastien; Bechti, Abdel; Khelifi Touhami, Amina; James, Marie José; Durel, Charles-Eric; Laurens, François; Costes, Evelyne

    2014-01-01

    In apple (Malus×domestica Borkh), as in many fruiting crops, fruit maintenance vs abscission is a major criteria for production profitability. Growers routinely make use of chemical thinning agents to control total fruit load. However, serious threats for the environment lead to the demand for new apple cultivars with self-thinning properties. In this project, we studied the genetic determinism of this trait using a F1 progeny derived from the cross between the hybrid INRA X3263, assumed to possess the self-thinning trait, and the cultivar 'Belrène'. Both counting and percentage variables were considered to capture the fruiting behaviour on different shoot types and over three consecutive years. Besides low to moderate but significant genetic effects, mixed models showed considerable effects of the year and the shoot type, as well as an interaction effect. Year effect resulted mainly from biennial fruiting. Eight Quantitative Trait Locus (QTL) were detected on several linkage groups (LG), either independent or specific of the year of observation or the shoot type. The QTL with highest LOD value was located on the top third of LG10. The screening of three QTL zones for candidate genes revealed a list of transcription factors and genes involved in fruit nutrition, xylem differentiation, plant responses to starvation and organ abscission that open new avenues for further molecular investigations. The detailed phenotyping performed revealed the dependency between the self-thinning trait and the fruiting status of the trees. Despite a moderate genetic control of the self-thinning trait, QTL and candidate genes were identified which will need further analyses involving other progenies and molecular investigations.

  19. Risks perception and the public acceptance of nuclear technology

    International Nuclear Information System (INIS)

    Ferreira, Walter Mendes; Gavazza, Sergio; Estrada, Julio J.S.

    2000-01-01

    This work establishes a methodology to evaluate the public acceptance of nuclear technology taking into consideration several risk concepts. Basic concepts of the nuclear science were transmitted, in form of lectures and courses, to the 13,439 Goiania residents, after the closing of the decontamination works, caused by the violation of the source of 137 Cs, of a teletherapy machine, in 1987. The results of the indicators shown that public's individuals perceive radiation risks and develop behaviors according to a constructive outline. The public does not know technical terms, being quite influenced by media, from where gets information of interest. The public orders the risks, relating them to accidents according to subjective criteria and models them as unknown, new and not observed at short period, establishing destruction, environmental catastrophe and diseases images. (author)

  20. Section 4. Further expanding the criteria for HCC in living donor liver transplantation: the Tokyo University experience.

    Science.gov (United States)

    Tamura, Sumihito; Sugawara, Yasuhiko; Kokudo, Norihiro

    2014-04-27

    In Asia, evidence-based guidelines for the management of hepatocellular carcinoma (HCC) have evolved, including the option of liver transplantation. Because of the continuing serious organ shortage, however, living donor liver transplantation (LDLT) remains the mainstream in Japan. Unlike deceased donor transplantation, living donor transplantation is not always limited by the restrictions imposed by the nationwide organ allocation system. The decision for transplantation may depend on institutional or case-by-case considerations, balancing the will of the donor, the operative risk, and the overall survival benefit. Cumulative data from the Japanese national multicenter registry analysis as well as individual center experiences suggest further expanding the criteria for LDLT for HCC from the Milan criteria is feasible with acceptable outcomes.