WorldWideScience

Sample records for thermogravimetric tg analysis

  1. Thermogravimetric analysis-mass spectrometry (TG-MS) of selected Chinese palygorskites-Implications for structural water

    International Nuclear Information System (INIS)

    Cheng, Hongfei; Yang, Jing; Frost, Ray L.

    2011-01-01

    Four Chinese palygorskites clay minerals have been analysed by thermogravimetric analysis-mass spectrometry and X-ray diffraction. The structural water of the palygorskite dehydrates in the temperature range of 30-625 o C, as shown in the thermogravimetric analysis and mass spectrometric curves. The mass spectrometric curves combined the differential thermogravimetric curves enable the detailed determination of the main dehydration steps. The results show that the dehydration occurs in four main steps: (a) elimination of interparticle water and partial zeolitic water at below 110 o C, (b) release of the rest part of zeolitic water from the structural layer of palygorskite at about 160 o C, (c) dehydration of one part of bound water at about 340 o C and (d) loss of the rest part of bound water at around 450 o C. The temperatures of dehydration of the palygorskite minerals are found to be influenced by the geological environment and the amount and kind of impurities. The evolved gases in the decomposition process are various because of the different amounts and kind of impurities. It is also found that decarbonization takes place at around 600 o C due to the decomposition of calcite and dolomite impurities in these minerals. It is evident by the mass spectrometric curve that the water is given out from the samples and carbon dioxide originates from the impurity calcite and dolomite.

  2. Thermogravimetric Analysis Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — At NETL’s Thermogravimetric Analysis Laboratory in Morgantown, WV, researchers study how chemical looping combustion (CLC) can be applied to fossil energy systems....

  3. Thermogravimetric analysis of reactor-neutrons-irradiated LEXAN polycarbonate film

    International Nuclear Information System (INIS)

    Kalsi, P.C.

    2000-01-01

    The effects of reactor-neutrons irradiation on the thermogravimetric (TG) analysis of LEXAN polycarbonate film in air were studied. Irradiation enhances the degradation rate and the effect increases further with increasing neutron fluence. The kinetics of the different steps of degradation were also evaluated from the TG curves. The activation energy values calculated for all the degradation stages decrease on irradiation. (author)

  4. Thermogravimetric analysis of biowastes during combustion

    International Nuclear Information System (INIS)

    Otero, M.; Sanchez, M.E.; Gomez, X.; Moran, A.

    2010-01-01

    The combustion of sewage sludge (SS), animal manure (AM) and the organic fraction of municipal solid waste (OFMSW) was assessed and compared with that of a semianthracite coal (SC) and of a PET waste by thermogravimetric (TG) analysis. Differences were found in the TG curves obtained for the combustion of these materials accordingly to their respective proximate analysis. Non-isothermal thermogravimetric data were used to assess the kinetics of the combustion of these biowastes. The present paper reports on the application of the Vyazovkin model-free isoconversional method for the evaluation of the activation energy necessary for the combustion of these biowastes. The activation energy related to SS combustion (129.1 kJ/mol) was similar to that corresponding to AM (132.5 kJ/mol) while the OFMSW showed a higher value (159.3 kJ/mol). These values are quite higher than the one determined in the same way for the combustion of SC (49.2 kJ/mol) but lower than that for the combustion of a PET waste (165.6 kJ/mol).

  5. Kinetic parameters from thermogravimetric analysis

    Science.gov (United States)

    Kiefer, Richard L.

    1993-01-01

    High performance polymeric materials are finding increased use in aerospace applications. Proposed high speed aircraft will require materials to withstand high temperatures in an oxidative atmosphere for long periods of time. It is essential that accurate estimates be made of the performance of these materials at the given conditions of temperature and time. Temperatures of 350 F (177 C) and times of 60,000 to 100,000 hours are anticipated. In order to survey a large number of high performance polymeric materials on a reasonable time scale, some form of accelerated testing must be performed. A knowledge of the rate of a process can be used to predict the lifetime of that process. Thermogravimetric analysis (TGA) has frequently been used to determine kinetic information for degradation reactions in polymeric materials. Flynn and Wall studied a number of methods for using TGA experiments to determine kinetic information in polymer reactions. Kinetic parameters, such as the apparent activation energy and the frequency factor, can be determined in such experiments. Recently, researchers at the McDonnell Douglas Research Laboratory suggested that a graph of the logarithm of the frequency factor against the apparent activation energy can be used to predict long-term thermo-oxidative stability for polymeric materials. Such a graph has been called a kinetic map. In this study, thermogravimetric analyses were performed in air to study the thermo-oxidative degradation of several high performance polymers and to plot their kinetic parameters on a kinetic map.

  6. Biomass Thermogravimetric Analysis: Uncertainty Determination Methodology and Sampling Maps Generation

    Science.gov (United States)

    Pazó, Jose A.; Granada, Enrique; Saavedra, Ángeles; Eguía, Pablo; Collazo, Joaquín

    2010-01-01

    The objective of this study was to develop a methodology for the determination of the maximum sampling error and confidence intervals of thermal properties obtained from thermogravimetric analysis (TG), including moisture, volatile matter, fixed carbon and ash content. The sampling procedure of the TG analysis was of particular interest and was conducted with care. The results of the present study were compared to those of a prompt analysis, and a correlation between the mean values and maximum sampling errors of the methods were not observed. In general, low and acceptable levels of uncertainty and error were obtained, demonstrating that the properties evaluated by TG analysis were representative of the overall fuel composition. The accurate determination of the thermal properties of biomass with precise confidence intervals is of particular interest in energetic biomass applications. PMID:20717532

  7. TG-FTIR analysis of biomass pyrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Bassilakis, R.; Carangelo, R.M.; Wojtowicz, M.A. [Advanced Fuel Research Inc., Hartford, CT (United States)

    2001-10-09

    A great need exists for comprehensive biomass-pyrolysis models that could predict yields and evolution patterns of selected volatile products as a function of feedstock characteristics and process conditions. A thermogravimetric analyzer coupled with Fourier transform infrared analysis of evolving products (TG-FTIR) can provide useful input to such models in the form of kinetic information obtained under low heating rate conditions. In this work, robust TG-FTIR quantification routes were developed for infrared analysis of volatile products relevant to biomass pyrolysis. The analysis was applied to wheat straw, three types of tobacco (Burley, Oriental, and Bright) and three biomass model compounds (xylan, chlorogenic acid, and D-glucose). Product yields were compared with literature data, and species potentially quantifiable by FT-IR are reviewed. Product-evolution patterns are reported for all seven biomass samples. 41 refs., 7 figs., 2 tabs.

  8. Thermal decomposition characteristics of microwave liquefied rape straw residues using thermogravimetric analysis

    Science.gov (United States)

    Xingyan Huang; Cornelis F. De Hoop; Jiulong Xie; Chung-Yun Hse; Jinqiu Qi; Yuzhu Chen; Feng Li

    2017-01-01

    The thermal decomposition characteristics of microwave liquefied rape straw residues with respect to liquefaction condition and pyrolysis conversion were investigated using a thermogravimetric (TG) analyzer at the heating rates of 5, 20, 50 °C min-1. The hemicellulose decomposition peak was absent at the derivative thermogravimetric analysis (DTG...

  9. Uncertainty Determination Methodology, Sampling Maps Generation and Trend Studies with Biomass Thermogravimetric Analysis

    Science.gov (United States)

    Pazó, Jose A.; Granada, Enrique; Saavedra, Ángeles; Eguía, Pablo; Collazo, Joaquín

    2010-01-01

    This paper investigates a method for the determination of the maximum sampling error and confidence intervals of thermal properties obtained from thermogravimetric analysis (TG analysis) for several lignocellulosic materials (ground olive stone, almond shell, pine pellets and oak pellets), completing previous work of the same authors. A comparison has been made between results of TG analysis and prompt analysis. Levels of uncertainty and errors were obtained, demonstrating that properties evaluated by TG analysis were representative of the overall fuel composition, and no correlation between prompt and TG analysis exists. Additionally, a study of trends and time correlations is indicated. These results are particularly interesting for biomass energy applications. PMID:21152292

  10. Thermogravimetric analysis of forest understory grasses

    Science.gov (United States)

    Thomas Elder; John S. Kush; Sharon M. Hermann

    2011-01-01

    Forest understory grasses are of significance in the initiation, establishment and maintenance of fire, whether used as a management tool or when occurring as wildfire. The fundamental thermal properties of such grasses are critical to their behavior in fire situations and have been investigated in the current work by the application of thermogravimetric analysis (TGA...

  11. Thermogravimetric analysis of fuel film evaporation

    Institute of Scientific and Technical Information of China (English)

    HU Zongjie; LI Liguang; YU Shui

    2006-01-01

    Thermogravimetric analysis (TGA) was compared with the petrochemical distillation measurement method to better understand the characteristics of fuel film evaporation at different wall tem- peratures. The film evaporation characteristics of 90# gasoline, 93# gasoline and 0# diesel with different initial thicknesses were investigated at different environmental fluxes and heating rates. The influences of heating rate, film thickness and environmental flux on fuel film evaporation for these fuels were found. The results showed that the environmental conditions in TGA were similar to those for fuel films in the internal combustion engines, so data from TGA were suitable for the analysis of fuel film evaporation. TGA could simulate the key influencing factors for fuel film evaporation and could investigate the basic quantificational effect of heating rate and film thickness. To get a rapid and sufficient fuel film evaporation, sufficiently high wall temperature is necessary. Evaporation time decreases at a high heating rate and thin film thickness, and intense gas flow is important to promoting fuel film evaporation. Data from TGA at a heating rate of 100℃/min are fit to analyze the diesel film evaporation during cold-start and warming-up. Due to the tense molecular interactions, the evaporation sequence could not be strictly divided according to the boiling points of each component for multicomponent dissolved mixture during the quick evaporation process, and the heavier components could vaporize before reaching their boiling points. The 0# diesel film would fully evaporate when the wall temperature is beyond 250℃.

  12. Thermogravimetric analysis and fast pyrolysis of Milkweed.

    Science.gov (United States)

    Kim, Seung-Soo; Agblevor, Foster A

    2014-10-01

    Pyrolysis of Milkweed was carried out in a thermogravimetric analyzer and a bubbling fluidized bed reactor. Total liquid yield of Milkweed pyrolysis was between 40.74% and 44.19 wt% between 425 °C and 550 °C. The gas yield increased from 27.90 wt% to 33.33 wt% with increasing reaction temperature. The higher heating values (HHV) of the Milkweed bio-oil were relatively high (30.33-32.87 MJ/kg) and varied with reaction temperature, feeding rate and fluidization velocity. The selectivity for CO2 was highest within non-condensable gases, and the molar ratio of CO2/CO was about 3 at the different reaction conditions. The (13)C NMR analysis, of the bio-oil showed that the relative concentration carboxylic group and its derivatives was higher at 425 °C than 475 °C, which resulted in slightly higher oxygen content in bio-oil. The pH of aqueous phase obtained at 475 °C was 7.37 which is the highest reported for any lignocellulosic biomass pyrolysis oils. Copyright © 2014 Elsevier Ltd. All rights reserved.

  13. Isothermal thermogravimetric data acquisition analysis system

    Science.gov (United States)

    Cooper, Kenneth, Jr.

    1991-01-01

    The description of an Isothermal Thermogravimetric Analysis (TGA) Data Acquisition System is presented. The system consists of software and hardware to perform a wide variety of TGA experiments. The software is written in ANSI C using Borland's Turbo C++. The hardware consists of a 486/25 MHz machine with a Capital Equipment Corp. IEEE488 interface card. The interface is to a Hewlett Packard 3497A data acquisition system using two analog input cards and a digital actuator card. The system provides for 16 TGA rigs with weight and temperature measurements from each rig. Data collection is conducted in three phases. Acquisition is done at a rapid rate during initial startup, at a slower rate during extended data collection periods, and finally at a fast rate during shutdown. Parameters controlling the rate and duration of each phase are user programmable. Furnace control (raising and lowering) is also programmable. Provision is made for automatic restart in the event of power failure or other abnormal terminations. Initial trial runs were conducted to show system stability.

  14. Thermogravimetric analysis and dissociation pressure of caesium trihalides

    International Nuclear Information System (INIS)

    Harris, G.S.; McKechnie, J.S.

    1982-01-01

    We have carried out a thermogravimetric study of caesium trihalides to obtain, from the procedural decomposition temperatures, an order of apparent thermal stability which could be compared with the order of thermodynamic stability obtained from vapour pressure measurements. Thermogravimetric analysis could also prove to be a useful method for rapid analysis of metal polyhalides. The thermograms indicated a one-step decomposition for each compound; the procedural decomposition temperatures and percentage weight losses obtained are given. Dissociation pressures were measured and values of equilibrium constant and enthalpy of dissociation were calculated. The results are given. The 'stability' order obtained is discussed. (U.K.)

  15. Thermogravimetric-quadrupole mass-spectrometric analysis of geochemical samples.

    Science.gov (United States)

    Gibson, E. K., Jr.; Johnson, S. M.

    1972-01-01

    Thermogravimetric-quadrupole mass-spectrometric-analysis techniques can be used to study a wide variety of problems involving decomposition processes and identification of released volatile components. A recording vacuum thermoanalyzer has been coupled with a quadrupole mass spectrometer. The rapid scan capabilities of the quadrupole mass spectrometer are used to identify the gaseous components released. The capability of the thermogravimetric-quadrupole mass spectrometer to provide analytical data for identification of the released volatile components, for determination of their sequence of release and for correlation of thermal-decomposition studies is illustrated by an analysis of the Orgueil carbonaceous chondrite.

  16. A simple, sensitive graphical method of treating thermogravimetric analysis data

    Science.gov (United States)

    Abraham Broido

    1969-01-01

    Thermogravimetric Analysis (TGA) is finding increasing utility in investigations of the pyrolysis and combustion behavior of materuals. Although a theoretical treatment of the TGA behavior of an idealized reaction is relatively straight-forward, major complications can be introduced when the reactions are complex, e.g., in the pyrolysis of cellulose, and when...

  17. Research on Mechanism of Paper Burning by Thermogravimetric Analysis

    Institute of Scientific and Technical Information of China (English)

    QIN Da; HAN Xingzhou; WANG Xiaoguang; QI Fengliang; WANG Zijie; GUO Zihan; HAO Hongguang

    2015-01-01

    The examination of charred document is a challenge and usually requires a careful application of certain scientific techniques due to its unstable property. To address this issue, the mechanism of paper burning was studied in this paper. Here thermal-gravimetry (TG) was applied to investigate five kinds of paper, along with their TG and derivative thermogravimetric curve (DTG) observed at different atmospheric conditions. The results showed that the shape of curves, albeit similar, varied with the physical and chemical composition of paper. In the burning process, dehydration and de-polymerization are the two main pathways for cellulose, the major ingredient of paper. The heating rate indicated little influence on the curves while the sort of atmosphere worked strongly. The reason is due to the lack of tar oxidation when nitrogen used as the atmospheric environment. At moderate temperature, de-polymerization prevails and the tar can be observed. With temperature increasing, the tar and cellulose are further decomposed, leading to products of high boiling-point. According to the results, the charred document can be classified as one of the dehydrated, tarred, charred and ashed. Except the ashed stage, the other three can be handled and the writing whereon can be deciphered. The results exposed hereof may provide a fundamental for examining and deciphering charred document.

  18. Heater-Integrated Cantilevers for Nano-Samples Thermogravimetric Analysis

    OpenAIRE

    Toffoli, Valeria; Carrato, Sergio; Lee, Dongkyu; Jeon, Sangmin; Lazzarino, Marco

    2013-01-01

    The design and characteristics of a micro-system for thermogravimetric analysis (TGA) in which heater, temperature sensor and mass sensor are integrated into a single device are presented. The system consists of a suspended cantilever that incorporates a microfabricated resistor, used as both heater and thermometer. A three-dimensional finite element analysis was used to define the structure parameters. TGA sensors were fabricated by standard microlithographic techniques and tested using mill...

  19. Curie temperature determination via thermogravimetric and continuous wavelet transformation analysis

    Energy Technology Data Exchange (ETDEWEB)

    Hasier, John; Nash, Philip [Thermal Processing Technology Center, IIT, Chicago, IL (United States); Riolo, Maria Annichia [University of Michigan, Center for the Study of Complex Systems, Ann Arbor, MI (United States)

    2017-12-15

    A cost effective method for conversion of a vertical tube thermogravimetric analysis system into a magnetic balance capable of measuring Curie Temperatures is presented. Reference and preliminary experimental data generated using this system is analyzed via a general-purpose wavelet based Curie point edge detection technique allowing for enhanced speed, ease and repeatability of magnetic balance data analysis. The Curie temperatures for a number of Heusler compounds are reported. (orig.)

  20. Thermogravimetric Analysis of Single-Wall Carbon Nanotubes

    Science.gov (United States)

    Arepalli, Sivram; Nikolaev, Pavel; Gorelik, Olga

    2010-01-01

    An improved protocol for thermogravimetric analysis (TGA) of samples of single-wall carbon nanotube (SWCNT) material has been developed to increase the degree of consistency among results so that meaningful comparisons can be made among different samples. This improved TGA protocol is suitable for incorporation into the protocol for characterization of carbon nanotube material. In most cases, TGA of carbon nanotube materials is performed in gas mixtures that contain oxygen at various concentrations. The improved protocol is summarized.

  1. Interactions of coal gangue and pine sawdust during combustion of their blends studied using differential thermogravimetric analysis.

    Science.gov (United States)

    Zhang, Yuanyuan; Zhang, Zhezi; Zhu, Mingming; Cheng, Fangqin; Zhang, Dongke

    2016-08-01

    The interactions between coal gangue and pine sawdust during the combustion process were studied using thermogravimetric analysis. The effect of the blending ratio, oxygen concentration and heating rate on the weight loss (TG) and differential thermogravimetric (TGA) profiles was examined. The TG and DTG curves of the blends were not additives of those of the individual materials, suggesting that interactions between coal gangue and pine sawdust had occurred during the combustion, especially in the temperature range of 400-600°C. Kinetic analysis confirmed that the combustion of coal gangue, pine sawdust and their blends was chemical reaction controlled. Further analysis revealed that the interactions between coal gangue and pine sawdust were primarily due to thermal effects rather than structural changes, with the thermal inertia of coal gangue dominating over the behaviour of the blends. The interactions decreased with decreasing the coal gangue ratio in the blend, oxygen concentration and heating rate. Copyright © 2016 Elsevier Ltd. All rights reserved.

  2. Thermogravimetric analysis of the gasification of microalgae Chlorella vulgaris.

    Science.gov (United States)

    Figueira, Camila Emilia; Moreira, Paulo Firmino; Giudici, Reinaldo

    2015-12-01

    The gasification of microalgae Chlorella vulgaris under an atmosphere of argon and water vapor was investigated by thermogravimetric analysis. The data were interpreted by using conventional isoconversional methods and also by the independent parallel reaction (IPR) model, in which the degradation is considered to happen individually to each pseudo-component of biomass (lipid, carbohydrate and protein). The IPR model allows obtaining the kinetic parameters of the degradation reaction of each component. Three main stages were observed during the gasification process and the differential thermogravimetric curve was satisfactorily fitted by the IPR model considering three pseudocomponents. The comparison of the activation energy values obtained by the methods and those found in the literature for other microalgae was satisfactory. Quantification of reaction products was performed using online gas chromatography. The major products detected were H2, CO and CH4, indicating the potential for producing fuel gas and syngas from microalgae. Copyright © 2015 Elsevier Ltd. All rights reserved.

  3. Characterization and thermogravimetric analysis of lanthanide hexafluoroacetylacetone chelates.

    Science.gov (United States)

    Shahbazi, Shayan; Stratz, S Adam; Auxier, John D; Hanson, Daniel E; Marsh, Matthew L; Hall, Howard L

    2017-01-01

    This work reports the thermodynamic characterizations of organometallic species as a vehicle for the rapid separation of volatile nuclear fission products via gas chromatography due to differences in adsorption enthalpy. Because adsorption and sublimation thermodynamics are linearly correlated, there is considerable motivation to determine sublimation enthalpies. A method of isothermal thermogravimetric analysis, TGA-MS and melting point analysis are employed on thirteen lanthanide 1,1,1,5,5,5-hexafluoroacetylacetone complexes to determine sublimation enthalpies. An empirical correlation is used to estimate adsorption enthalpies of lanthanide complexes on a quartz column from the sublimation data. Additionally, four chelates are characterized by SC-XRD, elemental analysis, FTIR and NMR.

  4. Heater-Integrated Cantilevers for Nano-Samples Thermogravimetric Analysis

    Directory of Open Access Journals (Sweden)

    Valeria Toffoli

    2013-12-01

    Full Text Available The design and characteristics of a micro-system for thermogravimetric analysis (TGA in which heater, temperature sensor and mass sensor are integrated into a single device are presented. The system consists of a suspended cantilever that incorporates a microfabricated resistor, used as both heater and thermometer. A three-dimensional finite element analysis was used to define the structure parameters. TGA sensors were fabricated by standard microlithographic techniques and tested using milli-Q water and polyurethane microcapsule. The results demonstrated that our approach provides a faster and more sensitive TGA with respect to commercial systems.

  5. Heater-Integrated Cantilevers for Nano-Samples Thermogravimetric Analysis

    Science.gov (United States)

    Toffoli, Valeria; Carrato, Sergio; Lee, Dongkyu; Jeon, Sangmin; Lazzarino, Marco

    2013-01-01

    The design and characteristics of a micro-system for thermogravimetric analysis (TGA) in which heater, temperature sensor and mass sensor are integrated into a single device are presented. The system consists of a suspended cantilever that incorporates a microfabricated resistor, used as both heater and thermometer. A three-dimensional finite element analysis was used to define the structure parameters. TGA sensors were fabricated by standard microlithographic techniques and tested using milli-Q water and polyurethane microcapsule. The results demonstrated that our approach provides a faster and more sensitive TGA with respect to commercial systems.

  6. Quantitation of Surface Coating on Nanoparticles Using Thermogravimetric Analysis.

    Science.gov (United States)

    Dongargaonkar, Alpana A; Clogston, Jeffrey D

    2018-01-01

    Nanoparticles are critical components in nanomedicine and nanotherapeutic applications. Some nanoparticles, such as metallic nanoparticles, consist of a surface coating or surface modification to aid in its dispersion and stability. This surface coating may affect the behavior of nanoparticles in a biological environment, thus it is important to measure. Thermogravimetric analysis (TGA) can be used to determine the amount of coating on the surface of the nanoparticle. TGA experiments run under inert atmosphere can also be used to determine residual metal content present in the sample. In this chapter, the TGA technique and experimental method are described.

  7. Mechanism study on cellulose pyrolysis using thermogravimetric analysis coupled with infrared spectroscopy

    Institute of Scientific and Technical Information of China (English)

    WANG Shurong; LIU Qian; LUO Zhongyang; WEN Lihua; CEN Kefa

    2007-01-01

    Based on the investigation of the polysaccharide structure of cellulose by using Fourier transform spectrum analysis,the pyrolysis behaviour of cellulose was studied at a heating rate of 20 K/min by thermogravimetric (TG) analysis coupled with Fourier transform infrared (FTIR) spectroscopy.Experimental results show that the decomposition of cellulose mainly occurs at the temperature range of 550-670 K.The weight loss becomes quite slow when the temperature increases further up to 680 K and the amount of residue reaches a mass percent of 14.7%.The FTIR analysis shows that free water is released first during cellulose pyrolysis,followed by depolymerization and dehydration.Glucosidic bond and carbon-carbon bond break into a series of hydrocarbons,alcohols,aldehydes,acids,etc.Subsequently these large-molecule compounds decompose further into gases,such as methane and carbon monoxide.

  8. Thermogravimetric analysis coupled with chemometrics as a powerful predictive tool for ß-thalassemia screening.

    Science.gov (United States)

    Risoluti, Roberta; Materazzi, Stefano; Sorrentino, Francesco; Maffei, Laura; Caprari, Patrizia

    2016-10-01

    β-Thalassemia is a hemoglobin genetic disorder characterized by the absence or reduced β-globin chain synthesis, one of the constituents of the adult hemoglobin tetramer. In this study the possibility of using thermogravimetric analysis (TGA) followed by chemometrics as a new approach for β-thalassemia detection is proposed. Blood samples from patients with β-thalassemia were analyzed by the TG7 thermobalance and the resulting curves were compared to those typical of healthy individuals. Principal Component Analysis (PCA) was used to evaluate the correlation between the hematological parameters and the thermogravimetric results. The thermogravimetric profiles of blood samples from β-thalassemia patients were clearly distinct from those of healthy individuals as result of the different quantities of water content and corpuscular fraction. The hematological overview showed significant decreases in the values of red blood cell indices and an increase in red cell distribution width value in thalassemia subjects when compared with those of healthy subjects. The implementation of a predictive model based on Partial Least Square Discriminant Analysis (PLS-DA) for β-thalassemia diagnosis, was performed and validated. This model permitted the discrimination of anemic patients and healthy individuals and was able to detect thalassemia in clinically heterogeneous patients as in the presence of δβ-thalassemia and β-thalassemia combined with Hb Lepore. TGA and Chemometrics are capable of predicting ß-thalassemia syndromes using only a few microliters of blood without any pretreatment and with an hour of analysis time. A fast, rapid and cost-effective diagnostic tool for the β-thalassemia screening is proposed. Copyright © 2016 Elsevier B.V. All rights reserved.

  9. Study and Thermogravimetric analysis of Poly N-4 Aminostyrol

    International Nuclear Information System (INIS)

    Meghezzi, A.; Lakhdar, Y.; Saidi, M.; Dadamoussa, B.

    2006-01-01

    The polyaminostyrol samples (PAS) and their copolymers with the styrol differing in position and quantity of amino-group, were obtained by polymerization of monomers on cyclogexan solution. The observed thermal effects were analyzed by the differential thermal analysis combined with a thermogravimetric analysis. It was found that the introduction of amino-groups into the polystyrols increased the temperature of total degradation of polymer from 150 till 260C. The increase in thermostability may be explained by the cohesion of macromolecules with the participation of amino-groups, which results in ammonium evolution, as well as in the decrease of valence area band of -NH2 grouping the region 3370-34440 cm. It was showed that the degree of cohesion formation and thermolysis rate depended on amino-group and their position into the cycle of benzene. (author)

  10. Kinetic Model of LiFePO4 Formation Using Non-Isothermal Thermogravimetric Analysis

    Directory of Open Access Journals (Sweden)

    Abdul Halim

    2014-03-01

    Full Text Available The formation reaction of LiFePO4 from decomposition of precursors LiOH, FeSO4.7H2O and (NH42HPO4 with mol ratio of Li:Fe:P=1:1:1 was investigated. The experiment was carried out by thermogravimetric differential thermal analysis (TG-DTA method using nitrogen as atmosfer at a constant heating rate to obtain kinetic constant parameters. Several heating rates were selected, there are 5, 7, 10, 15, 17.5, 22.5 and 25 °C/min. Activation energy, pre-exponential factor and reaction order were taken using Kissinger method and obtained respectively 56.086 kJ/mol, 6.95×108 min-1, and 1.058. Based on fitting result between reaction model and experiment were obtained that reaction obeyed the three dimension diffusion model. © 2014 BCREC UNDIP. All rights reservedReceived: 19th September 2013; Revised: 9th December 2013; Accepted: 23rd January 2014 [How to Cite: Halim, A., Widiyastuti, W., Setyawan, H., Winardi, S. (2014. Kinetic of LiFePO4 For-mation Using Non-isothermal Thermogravimetric Analysis. Bulletin of Chemical Reaction Engineering & Catalysis, 9 (1: 60-65. (doi:10.9767/bcrec.9.1.5508.60-65][Permalink/DOI: http://dx.doi.org/10.9767/bcrec.9.1.5508.60-65] 

  11. Thermogravimetric analysis of the beryllium/steam reaction

    Energy Technology Data Exchange (ETDEWEB)

    Druyts, Frank E-mail: fdruyts@sckcen.be; Iseghem, Pierre van

    2000-11-01

    In view of the safety assessment of new fusion reactor designs, kinetic data are needed on the beryllium/steam reaction. Therefore, thermogravimetric analysis was used to determine the reactivity of beryllium in steam as a function of temperature, irradiation history and porosity of the samples. To this purpose, reference unirradiated S-200 VHP beryllium samples were compared with specimens irradiated in the BR2 reactor up to fast neutron fluences (E>1 MeV) of respectively 1.6x10{sup 21} n cm{sup -2} (resulting in a helium content of 300 appm He and a theoretical density of 99.9%) and 4x10{sup 22} n cm{sup -2} (21000 appm He, 97.2% theoretical density). Kinetics were parabolic for all tested beryllium types at 600 deg. C. At 700 deg. C, kinetics were parabolic for the unirradiated and irradiated 99.9% dense beryllium, and accelerating/linear for the irradiated 97.2% material. At 800 deg. C, all samples showed accelerating/linear behaviour. There was no influence of porosity on the reaction rate of beryllium in steam within the limited investigated density range, except at 700 deg. C, where the measured reaction rate for the irradiated 97.2% dense samples is an order of magnitude higher than for the irradiated 99.9% dense specimens.

  12. Pyrolysis and combustion kinetics of lycopodium particles in thermogravimetric analysis

    Institute of Scientific and Technical Information of China (English)

    Seyed Alireza Mostafavi; Sadjad Salavati; Hossein Beidaghy Dizaji; Mehdi Bidabadi

    2015-01-01

    Biomass is a kind of renewable energy which is used increasingly in different types of combustion systems or in the production of fuels like bio-oil. Lycopodium is a cellulosic particle, with good combustion properties, of which microscopic images show that these particles have spherical shapes with identical diameters of 31 μm. The measured density of these particles is 1.0779 g/cm2. Lycopodium particles contain 64.06% carbon, 25.56% oxygen, 8.55% hydrogen and 1.83% nitrogen, and no sulfur. Thermogravimetric analysis in the nitrogen environment indicates that the maximum of particle mass reduction occurs in the temperature range of 250−550 °C where the maximum mass reduction in the DTG diagrams also occurs in. In the oxygen environment, an additional peak can also be observed in the temperature range of 500−600 °C, which points to solid phase combustion and ignition temperature of lycopodium particles. The kinetics of reactions is determined by curve fitting and minimization of error.

  13. Thermal decomposition kinetics of sorghum straw via thermogravimetric analysis.

    Science.gov (United States)

    Dhyani, Vaibhav; Kumar, Jitendra; Bhaskar, Thallada

    2017-12-01

    The thermal decomposition of sorghum straw was investigated by non-isothermal thermogravimetric analysis, where the determination of kinetic triplet (activation energy, pre-exponential factor, and reaction model), was the key objective. The activation energy was determined using different isoconversional methods: Friedman, Flynn-Wall-Ozawa (FWO), Kissinger-Akahira-Sunose (KAS), Starink, Iterative method of Chai & Chen, Vyazovkin AIC method, and Li & Tang equation. The pre-exponential factor was calculated using Kissinger's equation; while the reaction model was predicted by comparison of z-master plot obtained from experimental values with the theoretical plots. The values of activation energy obtained from isoconversional methods were further used for evaluation of thermodynamic parameters, enthalpy, entropy and Gibbs free energy. Results showed three zones of pyrolysis having average activation energy values of 151.21kJ/mol, 116.15kJ/mol, and 136.65kJ/mol respectively. The data was well fitting with two-dimension 'Valensi' model for conversion values from 0 to 0.4 with a coefficient of determination (R 2 ) value of 0.988, and with third order reaction model for values from 0.4 to 0.9 with an R 2 value of 0.843. Copyright © 2017 Elsevier Ltd. All rights reserved.

  14. 硫化环氧化天然橡胶的热分析%Thermogravimetric Analysis of ENR Vulcanizate

    Institute of Scientific and Technical Information of China (English)

    张北龙; 陈美; 刘惠伦

    2001-01-01

    The thermogravimetric analysis of ENR(epoxidized natural rubber) has been carried out byTG-DTG methods at temperature rising rate of 5, 10, 15 and 20 ℃ · rmin-1. The results showed thatthe activation energy of the thermoreaction in flowing air during the course of mass loss wasn't alwayskeep rising, but declined at mass loss of 1.0%~10.0%, 20.0%~30.0% and 70. 0%~80. 0%.

  15. Thermogravimetric and Kinetic Analysis of Raw and Torrefied Biomass Combustion

    Directory of Open Access Journals (Sweden)

    Kopczyński Marcin

    2015-06-01

    Full Text Available The use of torrefied biomass as a substitute for untreated biomass may decrease some technological barriers that exist in biomass co-firing technologies e.g. low grindability, high moisture content, low energy density and hydrophilic nature of raw biomass. In this study the TG-MS-FTIR analysis and kinetic analysis of willow (Salix viminalis L. and samples torrefied at 200, 220, 240, 260, 280 and 300 °C (TSWE 200, 220, 240, 260, 280 and 300, were performed. The TG-DTG curves show that in the case of willow and torrefied samples TSWE 200, 220, 240 and 260 there are pyrolysis and combustion stages, while in the case of TSWE 280 and 300 samples the peak associated with the pyrolysis process is negligible, in contrast to the peak associated with the combustion process. Analysis of the TG-MS results shows m/z signals of 18, 28, 29 and 44, which probably represent H2O, CO and CO2. The gaseous products were generated in two distinct ranges of temperature. H2O, CO and CO2 were produced in the 500 K to 650 K range with maximum yields at approximately 600 K. In the second range of temperature, 650 K to 800 K, only CO2 was produced with maximum yields at approximately 710 K as a main product of combustion process. Analysis of the FTIR shows that the main gaseous products of the combustion process were H2O, CO2, CO and some organics including bonds: C=O (acids, aldehydes and ketones, C=C (alkenes, aromatics, C-O-C (ethers and C-OH. Lignin mainly contributes hydrocarbons (3000-2800 cm−1, while cellulose is the dominant origin of aldehydes (2860-2770 cm−1 and carboxylic acids (1790-1650 cm−1. Hydrocarbons, aldehydes, ketones and various acids were also generated from hemicellulose (1790-1650 cm−1. In the kinetic analysis, the two-steps first order model (F1F1 was assumed. Activation energy (Ea values for the first stage (pyrolysis increased with increasing torrefaction temperature from 93 to 133 kJ/mol, while for the second stage (combustion it

  16. Thermogravimetric and differential thermal analysis of potassium bicarbonate contaminated cellulose

    Science.gov (United States)

    A. Broido

    1966-01-01

    When samples undergo a complicated set of simultaneous and sequential reactions, as cellulose does on heating, results of thermogravimetric and differential thermal analyses are difficult to interpret. Nevertheless, careful comparison of pure and contaminated samples, pyrolyzed under identical conditions, can yield useful information. In these experiments TGA and DTA...

  17. Studies of the thermal properties of horn keratin by dielectric spectroscopy, thermogravimetric analysis and differential thermal analysis

    International Nuclear Information System (INIS)

    Marzec, E.; Piskunowicz, P.; Jaroszyk, F.

    2002-01-01

    The dielectric and thermal properties of horn keratin have been studied bu dielectric spectroscopy in the frequency range 10 1 -10 5 Hz, thermogravimetric analysis (TG) and different thermal analysis (DTA). Measurement of non-irradiated and g amma - irradiated keratin with doses 5, 50 kGy were performed at temperature from 22 to 260 o C. The results revealed the occurrence of phase transitions related to release of loosely bound water and bound water up to 200 o Cand the denaturation of the crystalline structure above this temperature. The influence of γ-irradiation on the thermal behaviour of keratin is significant only in the temperature range of denaturation. The decrease in the temperature of denaturation would suggest that γ-irradiation initiates main-chain degradation. (authors)

  18. Synthesis, spectroscopic characterization and thermogravimetric analysis of two series of substituted (metallotetraphenylporphyrins

    Directory of Open Access Journals (Sweden)

    Rasha K. Al-Shewiki

    2017-06-01

    Full Text Available Subsequent treatment of H2TPP(CO2H4 (tetra(p-carboxylic acid phenylporphyrin, 1 with an excess of oxalyl chloride and HNR2 afforded H2TPP(C(ONR24 (R = Me, 2; iPr, 3 with yields exceeding 80%. The porphyrins 2 and 3 could be converted to the corresponding metalloporphyrins MTPP(C(ONR24 (R = Me/iPr for M = Zn (2a, 3a; Cu (2b, 3b; Ni (2c, 3c; Co (2d, 3d by the addition of 3 equiv of anhydrous MCl2 (M = Zn, Cu, Ni, Co to dimethylformamide solutions of 2 and 3 at elevated temperatures. Metalloporphyrins 2a–d and 3a–d were obtained in yields exceeding 60% and have been, as well as 2 and 3, characterized by elemental analysis, electrospray ionization mass spectrometry (ESIMS and IR and UV–vis spectroscopy. Porphyrins 2, 2a–d and 3, 3a–d are not suitable for organic molecular beam deposition (OMBD, which is attributed to their comparatively low thermal stability as determined by thermogravimetric analysis (TG of selected representatives.

  19. Synthesis, spectroscopic characterization and thermogravimetric analysis of two series of substituted (metallo)tetraphenylporphyrins.

    Science.gov (United States)

    Al-Shewiki, Rasha K; Mende, Carola; Buschbeck, Roy; Siles, Pablo F; Schmidt, Oliver G; Rüffer, Tobias; Lang, Heinrich

    2017-01-01

    Subsequent treatment of H 2 TPP(CO 2 H) 4 (tetra( p -carboxylic acid phenyl)porphyrin, 1 ) with an excess of oxalyl chloride and HNR 2 afforded H 2 TPP(C(O)NR 2 ) 4 (R = Me, 2 ; iPr, 3 ) with yields exceeding 80%. The porphyrins 2 and 3 could be converted to the corresponding metalloporphyrins MTPP(C(O)NR 2 ) 4 (R = Me/iPr for M = Zn ( 2a , 3a ); Cu ( 2b , 3b ); Ni ( 2c , 3c ); Co ( 2d , 3d )) by the addition of 3 equiv of anhydrous MCl 2 (M = Zn, Cu, Ni, Co) to dimethylformamide solutions of 2 and 3 at elevated temperatures. Metalloporphyrins 2a - d and 3a - d were obtained in yields exceeding 60% and have been, as well as 2 and 3 , characterized by elemental analysis, electrospray ionization mass spectrometry (ESIMS) and IR and UV-vis spectroscopy. Porphyrins 2 , 2a - d and 3 , 3a - d are not suitable for organic molecular beam deposition (OMBD), which is attributed to their comparatively low thermal stability as determined by thermogravimetric analysis (TG) of selected representatives.

  20. Thermogravimetric study and kinetic analysis of dried industrial sludge pyrolysis.

    Science.gov (United States)

    Liu, Guangrui; Song, Huijuan; Wu, Jinhu

    2015-07-01

    Thermogravimetric experiments of two different industrial sludge samples were carried out with non-isothermal temperature programs. The results indicated that the pyrolysis process contains three obvious stages and the main decomposition reaction occurred in the range of 200-600°C. The distributed activation energy model (DAEM) was also proposed describing equally well the pyrolysis behavior of the samples. The calculated activation energy was ranged from 170 to 593kJ/mol and 125 to 756kJ/mol for SLYG (sludge sample from chemical fiber factory) and SQD (sludge sample from woody industry), respectively. The reliability of this model not only provided good fit for all experiments, but also allowed accurate extrapolations to relative higher heating rates. Besides, the FTIR measurement was also used to further understand the relationship between pyrolysis behavior and chemical structures for industrial sludge. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. The research of moisture forms in the baking yeast by the thermogravimetric analysis method

    Directory of Open Access Journals (Sweden)

    S. V. Lavrov

    2016-01-01

    Full Text Available The thermogravimetry method is one of the few absolute methods of analysis, that makes it one of the most accurate methods. In this research, thermogravimetric analysis of baking yeast (Saccharomyces cerevisiae was carried out. It allowed to identify temperature zones, which correspond to dripping with various link energy, as well as to predict operating parameters of the process of dehumidification and to choose their most effective dehydration method. The studies were conducted in the laboratory of the collective use center "Control and management of energy efficient projects" of the "Voronezh state university of engineering technologies" on the simultaneous thermal analysis device STA 449 F3 model (NETZSCH, Germany. The device records the change in a substance mass and the difference of the heat flow inside the crucible containing the sample and the crucible containing the standard analyte. The analyzer's working principle is based on continuous recording of the dependence of the material mass on time or temperature and its being heated to the selected temperature program in a specified gas atmosphere. The release or absorption of heat by the sample due to phase transitions or chemical reactions is recorded simultaneously. The study was performed in the following modes: the pressure is atmospheric, the maximum temperature is 588 K, the rate of temperature change is 5 K/min. The experiments were performed in aluminum crucibles with a total weight of 12 mg. The software NETZSCH Proteus was used for processing of the obtained TG and DTG curves. The analysis of the obtained data allowed to identify periods of water dehydration and solids transformation by thermal effect on baking yeast, and to identify temperature zones, which correspond to the release of moisture with different link form and energy.

  2. Thermogravimetric analysis in the characterization of colombian coals used in the production of coke

    International Nuclear Information System (INIS)

    Guerrero, Camilo; Salamanca, Monica E; Diaz, Jose de J

    2010-01-01

    Five types of coal from the states of Cundinamarca, Boyaca and Norte de Santander (Colombia) were characterized by proximate, ultimate, rheological, petrographic, calorific and thermogravimetric analysis. The parameters used, especially the ones which determine the rheological properties show that the studied coals and its blends could produce good quality coke. It was observed the inverse relationship between the volatile matter content and the mean vitrinite reflectance, relationship which is attributed to the increase of the aromaticity in the molecular structure of the coal as a consequence of the rank increase. The parameters derived from the thermogravimetric analysis, maximum velocity of de-volatilization and the temperature of maximum velocity of de-volatilization and the media reflectance of the vitrinite showed good correlations. Also was observed an interesting correlation between the velocity of de-volatilization and maximum fluidity. This shows that the thermogravimetric analysis can be a useful tool to characterize in a quick way coals used for metallurgical coke production.

  3. Chemometric modeling of thermogravimetric data for the compositional analysis of forest biomass.

    Science.gov (United States)

    Acquah, Gifty E; Via, Brian K; Fasina, Oladiran O; Adhikari, Sushil; Billor, Nedret; Eckhardt, Lori G

    2017-01-01

    The objective of this study was to investigated the use of chemometric modeling of thermogravimetric (TG) data as an alternative approach to estimate the chemical and proximate (i.e. volatile matter, fixed carbon and ash contents) composition of lignocellulosic biomass. Since these properties affect the conversion pathway, processing costs, yield and / or quality of products, a capability to rapidly determine these for biomass feedstock entering the process stream will be useful in the success and efficiency of bioconversion technologies. The 38-minute long methodology developed in this study enabled the simultaneous prediction of both the chemical and proximate properties of forest-derived biomass from the same TG data. Conventionally, two separate experiments had to be conducted to obtain such information. In addition, the chemometric models constructed with normalized TG data outperformed models developed via the traditional deconvolution of TG data. PLS and PCR models were especially robust in predicting the volatile matter (R2-0.92; RPD- 3.58) and lignin (R2-0.82; RPD- 2.40) contents of the biomass. The application of chemometrics to TG data also made it possible to predict some monomeric sugars in this study. Elucidation of PC loadings obtained from chemometric models also provided some insights into the thermal decomposition behavior of the chemical constituents of lignocellulosic biomass. For instance, similar loadings were noted for volatile matter and cellulose, and for fixed carbon and lignin. The findings indicate that common latent variables are shared between these chemical and thermal reactivity properties. Results from this study buttresses literature that have reported that the less thermally stable polysaccharides are responsible for the yield of volatiles whereas the more recalcitrant lignin with its higher percentage of elementary carbon contributes to the yield of fixed carbon.

  4. Chemometric modeling of thermogravimetric data for the compositional analysis of forest biomass.

    Directory of Open Access Journals (Sweden)

    Gifty E Acquah

    Full Text Available The objective of this study was to investigated the use of chemometric modeling of thermogravimetric (TG data as an alternative approach to estimate the chemical and proximate (i.e. volatile matter, fixed carbon and ash contents composition of lignocellulosic biomass. Since these properties affect the conversion pathway, processing costs, yield and / or quality of products, a capability to rapidly determine these for biomass feedstock entering the process stream will be useful in the success and efficiency of bioconversion technologies. The 38-minute long methodology developed in this study enabled the simultaneous prediction of both the chemical and proximate properties of forest-derived biomass from the same TG data. Conventionally, two separate experiments had to be conducted to obtain such information. In addition, the chemometric models constructed with normalized TG data outperformed models developed via the traditional deconvolution of TG data. PLS and PCR models were especially robust in predicting the volatile matter (R2-0.92; RPD- 3.58 and lignin (R2-0.82; RPD- 2.40 contents of the biomass. The application of chemometrics to TG data also made it possible to predict some monomeric sugars in this study. Elucidation of PC loadings obtained from chemometric models also provided some insights into the thermal decomposition behavior of the chemical constituents of lignocellulosic biomass. For instance, similar loadings were noted for volatile matter and cellulose, and for fixed carbon and lignin. The findings indicate that common latent variables are shared between these chemical and thermal reactivity properties. Results from this study buttresses literature that have reported that the less thermally stable polysaccharides are responsible for the yield of volatiles whereas the more recalcitrant lignin with its higher percentage of elementary carbon contributes to the yield of fixed carbon.

  5. Characterization of an alkali-treated grass fiber by thermogravimetric and X-ray crystallographic analysis

    NARCIS (Netherlands)

    De, D.; De, Debapriya

    2008-01-01

    The thermal behavior of grass fiber was characterized by means of thermogravimetric analysis and differential scanning calorimetry analysis. The results proved that the removal of water-soluble matter improved the thermal behavior of grass fiber over that of unleached fiber, and this was further

  6. Thermogravimetric and Kinetic Analysis of Cassava Starch Based Bioplastic

    Directory of Open Access Journals (Sweden)

    Nanang Eko Wahyuningtyas

    2017-11-01

    Full Text Available Cassava starch based bioplasticfor packaging application has great potency because of the various starch-producing plants in Indonesia.Bioplasticcan contribute to reduce the dependence on fossil fuels andpetroleumthat can solve the environmentalproblem.Thepurpose of this research is to find out the thermal decomposition and the activation energy of cassava starch based bioplastic. The methods weresynthesis bioplastic with cassava starch as main component and glycerol as plasticizer. The thermogravimetry analysis was conducted to obtain the decomposition process mechanism of bioplastic and the heating valueof bioplasticwas measured  using theadiabatic bomb calorimetric.  Data analysis was conducted using  a fitting model approach with an acikalin method to determine the activation energy. The result of thethermogravimetricanalysis showed thatbioplasticisgraduallydecomposedto the moisture, volatilematter, fixed carbon, andash in four stages mechanism. Totally decomposition of bioplastic was 530°C, then all of bioplastic was become the ash. The activation energy in the early and primary thermal decomposition stages are 1.27 kJ/moland 22.62 kJ/mol, respectively and heating valueof bioplastic is 15.16 MJ/kg.

  7. Kinetics of devolatilisation of forestry wastes from thermogravimetric analysis

    Energy Technology Data Exchange (ETDEWEB)

    Lapuerta, M.; Hernandez, J.J. [Universidad de Castilla-La Mancha, Ciudad real (Spain). Escuela Tecnica Superior de Ingenieros Industriales; Rodriguez, J.J. [Repsol-YPF, Puertollano (Spain). Chemical Department

    2004-10-01

    The great potential of Maritime pine (Pinus pinaster) wastes in the middle regions of Spain has motivated an increasing interest about the energy use of this material, either through combustion or gasification processes. Samples of these biomass wastes have been analysed by thermogravimetry under both inert and oxidant atmospheres, from room temperature up to 1100 K, at different heating rates: 10, 30, 40, 50 and 60 K min{sup -1}. An estimation of the proximate analysis of the samples was made from combination of both resulting weight loss curves. The devolatilisation process of the samples was divided into three non-interacting mass-loss events described as parallel first-order reactions, being the first event identified as the moisture loss process, the second one as the hemicellulose and cellulose decomposition process and the third one as that of lignin decomposition. A fitting algorithm to obtain the kinetic parameters permitted a good agreement with experimental results, as well as a good discrimination of the effect of the heating rate. Due to the non-homogeneous nature of the tested samples, the use of other conventional methods for obtaining the kinetic parameters has been proved to be inadequate. (author)

  8. Thermogravimetric and Pyrolysis-Capillary Gas Chromatography-Mass Spectrometric Analysis of Pinus Halepensis Mill. Wood

    International Nuclear Information System (INIS)

    Hafsi, S.; Benbouzid, M.; Zimny, T.

    2005-01-01

    The analytical methods TG and Py-capillary-GC-MS were used to study the thermal degradation of Pinus Halepensis Mill. wood. The TG analysis in air and in nitrogen showed that the percentage content of char and ash were, 23.1% and 7.7% respectively. TG and DTG analysis proved that the evolution of organic degradation products occurs mainly between 215C and 380C and has its maximum evolution rate at 360C in nitrogen and 347C in air. Py-capillary-GC-MS analysis of the pyrolysis at 400C identified the presence of valuable chemicals such aliphatic and aromatic hydrocarbons, phenols, aldehydes, esters and saturated and unsaturated long chain fatty acids. (author)

  9. The degree of hydration assessment of blended cement pastes by differential thermal and thermogravimetric analysis. Morphological evolution of the solid phases

    International Nuclear Information System (INIS)

    Monteagudo, S.M.; Moragues, A.; Gálvez, J.C.; Casati, M.J.; Reyes, E.

    2014-01-01

    Highlights: • A proposal of hydration degree calculation for blended cement pastes is presented. • The method is based both on the contributions of various authors and on DTA–TG results. • Paste and mortar specimens with BFS, FA and SF mineral admixtures were used. • The evaluation of CH gives information on hydration and pozzolanic reactions. • The assessment of α provides an insight into future strength evolution. - Abstract: The degree of hydration assessment of cement paste from differential thermal and thermogravimetric analysis data has been performed by several authors that have offered a number of proposals for technical application to blended cements. In this paper, two calculation methods are studied in detail. Then, a proposal of the degree of hydration calculation for blended cements, based on the analysis of experimental results of DTA–TG, is presented. The proposed method combines the contributions of the authors and allows straightforward calculation of the degree of hydration from the experimental results. Validation of the methodology was performed by macroscopic and microstructural tests through paste and mortar specimens with blast furnace slag, flying ash and silica fume mineral admixtures bei(g)ng used. Tests of scanning electron microscopy with an energy dispersive analyser on paste specimens, and of mechanical strength on mortar specimens with the same percentages of substitution, were performed. They showed good agreement with the information derived from the differential thermal and thermogravimetric analysis data

  10. Thermogravimetric analysis and thermal degradation behaviour of advanced PMR-X carbon fiber composites

    International Nuclear Information System (INIS)

    Rngie, M.

    2003-01-01

    Thermal degradation behavior of sized and unsized carbon fibers in polyimide matrix was investigated. Degradation of neat resin and unidirectional laminates were investigated by thermogravimetric analysis technique at temperatures between 470 d ig C -650 d ig C and up to 250 h rs. Isothermal ageing of the PMR-X composite samples under different test conditions (i. e. different temperatures and prolonged aging times), showed that oxidation and degradation occurs in stage three different rates. Thermogravimetric analysis showed that the cured PMR-X composite panels are more stable in an inert atmosphere (nitrogen atmosphere)than in air and the degradation of neat resin is much higher than the composite samples. However, the rate of degradation of the unsized untreated carbon fibers in nitrogen environment is much higher than that for the PMR-X composites containing sized fibers

  11. Strategy for thermo-gravimetric analysis of K East fuel samples

    International Nuclear Information System (INIS)

    Lawrence, L.A.

    1997-01-01

    A strategy was developed for the Thermo-Gravimetric Analysis (TGA) testing of K East fuel samples for oxidation rate determinations. Tests will first establish if there are any differences for dry air oxidation between the K West and K East fuel. These tests will be followed by moist inert gas oxidation rate measurements. The final series of tests will consider pure water vapor i.e., steam

  12. Thermogravimetric analysis of silicon carbide-silicon nitride fibers at ambient to 1000 C in air

    Science.gov (United States)

    Daniels, J. G.; Ledbetter, F. E., III; Clemons, J. M.; Penn, B. G.

    1984-01-01

    Thermogravimetric analysis of silicon carbide-silicon nitride fibers was carried out at ambient to 1000 C in air. The weight loss over this temperature range was negligible. In addition, the oxidative stability at high temperature for a short period of time was determined. Fibers heated at 1000 C in air for fifteen minutes showed negligible weight loss (i.e., less than 1 percent).

  13. Thermogravimetric analysis of the polymer acrylate-vinyl ether mixture cured by radiation

    International Nuclear Information System (INIS)

    Danu, Sugiarto

    1998-01-01

    An experiment on thermal stability of the polymer acrylate-vinyl ether mixture cured by radiation have been done using thermogravimetric analysis. Three kinds of acrylic oligomers i.e., epoxy acrylate, urethane acrylate, and polypropylene glycol diacrylate, and vinyl ether monomers i.e., triethylene glycol divinyl ether (DVE-3), 1,4-cyclohexane dimethanol divinyl ether (CHVE), and butanediol monovinyl ether (HBVE) were used in the experiment. Reaction was taken via radical and cationic polymerisation. In case of cationic polymerisation, diphenyliodonium hexafluorophosphate fotoinisiator was used in the formulation. Thermogravimetric analysis was conducted in a nitrogen atmosphere at a flow rate of 40 ml/minute with a constant heating rate 10 o C and evaluation range were done from 25 to 500 o C. The results of thermogravimetric analysis showed that acrylate and DVE-3 mixture produced the polymer films with higher thermal stability than the mixture of acrylate with CHVE or HBVE. The composition of acrylate-vinyl ether mixture and degree of unsaturation of vinyl ether monomers influenced the thermal stability of polymer. The mixture of epoxy acrylate-vinyl ether and polypropylene glycol diacrylate-vinyl ether have 1 initial decomposition temperature whereas the urethane acrylate-vinyl ether mixture has 2 initial decomposition temperatures. (authors)

  14. Purity Evaluation of Single-Walled Carbon Nanotubes Using Thermogravimetric Analysis

    International Nuclear Information System (INIS)

    Goak, Jeung Choon; Kim, Tae Yang; Jung, Jongwan; Seo, Young-Soo; Lee, Naesung; Sok, Junghyun

    2013-01-01

    This study evaluated the purity of single-walled carbon nanotubes (SWCNTs) in the arc-synthesized SWCNT samples by using thermogravimetric analysis (TGA). The as-produced SWCNT samples were heat-treated in air for 20 h at 275-475°C and characterized by scanning and transmission electron microscopes and TGA to establish oxidation temperature ranges of SWCNTs and carbonaceous impurities comprising the samples. Based on these oxidation temperature ranges, derivative thermogravimetric curves were deconvoluted, and differentiated peaks were assigned to SWCNTs and carbonaceous impurities. The compositions and the SWCNT purities of the samples were obtained simply by calculating the areal ratios under the deconvoluted curves. TGA studies on purity evaluation and thermal stabilities of SWCNTs and carbonaceous impurities are likely to provide us with a simple route of thermal oxidation purification to acquire high-purity SWCNT samples.

  15. Investigation of thermodynamic parameters in the pyrolysis conversion of biomass and manure to biochars using thermogravimetric analysis.

    Science.gov (United States)

    Xu, Yiliang; Chen, Baoliang

    2013-10-01

    The thermodynamic parameters of the conversion of two companion pair materials, i.e., rice straw vs dairy manure, and rice bran vs chicken manure, to biochars were characterized by thermogravimetric analysis. The overall changes of activation energy (Ea) were well described by the Flynn-Wall method. The Ea values increased steeply from about 120 to 180 kJ/mol at the mass conversion (α) at 0.2-0.4, followed by a relatively steady change at 0.40.65. The higher contents of minerals in manures resulted in the larger Ea. The individual conversion of hemicellulose, cellulose and lignin in the feedstocks was identified and their thermodynamic parameters (ΔH°, ΔG° and ΔS°) were calculated. The yields of biochars calculated from TG curve were compared with the determined yields of biochars using muffle pyrolysis. Along with Fourier transform infrared spectra data, the distinct decompositions of biomasses and manures were evaluated. Copyright © 2013 Elsevier Ltd. All rights reserved.

  16. Understanding of thermo-gravimetric analysis to calculate number of addends in multifunctional hemi-ortho ester derivatives of fullerenol

    International Nuclear Information System (INIS)

    Singh, Rachana; Goswami, Thakohari

    2011-01-01

    Test results for the applicability of existing thermo-gravimetric analysis (TGA) technique to ascertain average number of exohedral chemical attachment in a new class of fullerene dyads consisting of multiple hemi-ortho esters onto fullerenol is presented. Although the method is nicely applicable for higher fullerenol, but homogeneous phase products calculate lower number of addends, whereas, the hetero phase products indicate higher value. Lower value is attributed to either overlapping of thermal events or substituents effects and higher value is the contribution of tetra butyl ammonium hydroxide (TBAH) impurity used as phase transfer catalyst (PTC) in heterogeneous phase reactions. Presence of TBAH impurity is recognized through thermo-gravimetry mass spectrometry (TG-MS) measurement. Appropriate modification of test method to arrive at accurate and precise values of x (total mass contribution due to addends only) and y (total mass contribution due to fullerene plus char yield) are also reported. Successful use of two more different techniques, viz., electron-spray ionization mass spectrometry (ESI-MS) and X-ray photoelectron spectroscopy (XPS), supplement above results. Influences of fullerene and different substituents on thermal behavior of dyads are assessed.

  17. Thermal degradation of Shredded Oil Palm Empty Fruit Bunches (SOPEFB) embedded with Cobalt catalyst by Thermogravimetric Analysis (TGA)

    Science.gov (United States)

    Alias, R.; Hamid, N. H.; Jaapar, J.; Musa, M.; Alwi, H.; Halim, K. H. Ku

    2018-03-01

    Thermal behavior and decomposition kinetics of shredded oil palm empty fruit bunches (SOPEFB) were investigated in this study by using thermogravimetric analysis (TGA). The SOPEFB were analyzed under conditions of temperature 30 °C to 900 °C with nitrogen gas flow at 50 ml/min. The SOPEFB were embedded with cobalt (II) nitrate solution with concentration 5%, 10%, 15% and 20%. The TG/DTG curves shows the degradation behavior of SOPEFB following with char production for each heating rate and each concentration of cobalt catalyst. Thermal degradation occurred in three phases, water drying phase, decomposition of hemicellulose and cellulose phase, and lignin decomposition phase. The kinetic equation with relevant parameters described the activation energy required for thermal degradation at the temperature regions of 200 °C to 350 °C. Activation energy (E) for different heating rate with SOPEFB embedded with different concentration of cobalt catalyst showing that the lowest E required was at SOPEFB with 20% concentration of cobalt catalyst..

  18. Comparative evaluation of thermal oxidative decomposition for oil-plant residues via thermogravimetric analysis: Thermal conversion characteristics, kinetics, and thermodynamics.

    Science.gov (United States)

    Chen, Jianbiao; Wang, Yanhong; Lang, Xuemei; Ren, Xiu'e; Fan, Shuanshi

    2017-11-01

    Thermal oxidative decomposition characteristics, kinetics, and thermodynamics of rape straw (RS), rapeseed meal (RM), camellia seed shell (CS), and camellia seed meal (CM) were evaluated via thermogravimetric analysis (TGA). TG-DTG-DSC curves demonstrated that the combustion of oil-plant residues proceeded in three stages, including dehydration, release and combustion of organic volatiles, and chars oxidation. As revealed by combustion characteristic parameters, the ignition, burnout, and comprehensive combustion performance of residues were quite distinct from each other, and were improved by increasing heating rate. The kinetic parameters were determined by Coats-Redfern approach. The results showed that the most possible combustion mechanisms were order reaction models. The existence of kinetic compensation effect was clearly observed. The thermodynamic parameters (ΔH, ΔG, ΔS) at peak temperatures were calculated through the activated complex theory. With the combustion proceeding, the variation trends of ΔH, ΔG, and ΔS for RS (RM) similar to those for CS (CM). Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. Making the Tg-Confinement Effect Disappear in Thin Polystyrene Films: Good Physics vs. Inappropriate Analysis

    Science.gov (United States)

    Torkelson, John; Chen, Lawrence

    2013-03-01

    The Tg-confinement effect in polymers was first characterized in supported polystyrene (PS) films by Keddie et al. in 1994. Since then, many researchers have shown that (pseudo-)thermodynamic Tg measurements of supported PS films taken on cooling consistently yield the same qualitative results, with a decrease from bulk Tg beginning at 40-60 nm thickness and becoming very strong below 20 nm thickness. Some quantitative differences have been noted between studies, which may be ascribed to measurement method or the analysis employed. In 2004, we showed that the Tg-confinement effect in PS may be suppressed by adding several wt% of small-molecule diluents such as dioctyl phthalate. Recently, Kremer and co-workers (Macromolecules 2010, 43, 9937) reported that there was no Tg-confinement in supported PS films based on an analysis of the second derivative of ellipsometry data and use of a ninth order polynomial fit. Here, we demonstrate a new method for suppressing the Tg-confinement effect. In particular, PS made by emulsion polymerization yields no Tg-confinement effect as measured by ellipsometry or fluorescence, while PS made by anionic or conventional free radical polymerization yield strong Tg-confinement effects. The difference is hypothesized to result from surfactant in the emulsion polymerized PS. We also show that the absence of the Tg-confinement effect reported by Kremer is due to inappropriate analysis of ellipsometry data and that correct analysis yields Tg-confinement effects.

  20. Thermogravimetric analysis of anthracite and waste plastics by iso-conversional method

    International Nuclear Information System (INIS)

    Ren, Shan; Zhang, Jianliang

    2013-01-01

    Highlights: • Co-combustion kinetic analysis of solid fuels was made by iso-conversional method. • Thermodynamic and kinetic parameters of combustion for blends were determined. • WP can improve the combustion characteristic of high ash anthracite. • Reasonable utilization the energy of WP is important for industrial production. - Abstract: Combustion mechanisms and kinetics of plastics-coal blends with 0, 10, 20, 40 and 100% waste plastics (WP) are studied separately by thermogravimetric analysis (TGA) from ambient temperature to 900 °C in air atmosphere. These blends are combusted at different heating rates. The results indicate that, with the increase of waste plastics content, the combustion processes of blends could be divided into one stage, two stages, three stages and one stage. Meanwhile, the ignition and final temperatures of them both decrease. The maximum weight loss rate of WP is much higher than that of other samples. The iso-conversional method is used for the kinetic analysis of the non-isothermal thermogravimetric data and results indicate that, when the waste plastics content varied from 0% to 40%, the values of activation energy increase from 113.3 kJ mol −1 to 156.0 kJ mol −1 , and the value of activation energy for pure WP is 278.8 kJ mol −1

  1. Determination of nanoparticle surface coatings and nanoparticle purity using microscale thermogravimetric analysis.

    Science.gov (United States)

    Mansfield, Elisabeth; Tyner, Katherine M; Poling, Christopher M; Blacklock, Jenifer L

    2014-02-04

    The use of nanoparticles in some applications (i.e., nanomedical, nanofiltration, or nanoelectronic) requires small samples with well-known purities and composition. In addition, when nanoparticles are introduced into complex environments (e.g., biological fluids), the particles may become coated with matter, such as proteins or lipid layers. Many of today's analytical techniques are not able to address small-scale samples of nanoparticles to determine purity and the presence of surface coatings. Through the use of an elevated-temperature quartz crystal microbalance (QCM) method we call microscale thermogravimetric analysis, or μ-TGA, the nanoparticle purity, as well as the presence of any surface coatings of nanomaterials, can be measured. Microscale thermogravimetric analysis is used to determine the presence and amount of surface-bound ligand coverage on gold nanoparticles and confirm the presence of a poly(ethylene glycol) coating on SiO2 nanoparticles. Results are compared to traditional analytical techniques to demonstrate reproducibility and validity of μ-TGA for determining the presence of nanoparticle surface coatings. Carbon nanotube samples are also analyzed and compared to conventional TGA. The results demonstrate μ-TGA is a valid method for quantitative determination of the coatings on nanoparticles, and in some cases, can provide purity and compositional data of the nanoparticles themselves.

  2. Pyrolysis of coal, biomass and their blends: performance assessment by thermogravimetric analysis.

    Science.gov (United States)

    Ferrara, Francesca; Orsini, Alessandro; Plaisant, Alberto; Pettinau, Alberto

    2014-11-01

    With the aim to support the experimental tests in a gasification pilot plant, the thermal decomposition of coal, biomass and their mixtures has been carried out through a thermogravimetric analysis (TGA) and a simplified kinetic analysis. The TGA of pure fuels indicates the low reactivity of South African coal and the relatively high reactivity of Sardinian Sulcis coal during pyrolysis. Among the tested fuels, biomass (stone pine wood chips) is the most reactive one. These results fully confirm those obtained during the experimental tests in the gasification pilot plant. As for the fuel blends, the analysis shows that the synergic effects between the considered coals and biomass are negligible when they are co-pyrolyzed. The results of the analysis confirm that TGA could be very useful to generally predict the gasification performance and to optimize the experimental campaigns in pilot-scale gasification plants. Copyright © 2014 Elsevier Ltd. All rights reserved.

  3. Thermal behavior and kinetics assessment of ethanol/gasoline blends during combustion by thermogravimetric analysis

    International Nuclear Information System (INIS)

    3, CEP 12.516-410 Guaratinguetá, SP (Brazil); U.T.P. – Universidad Tecnológica de Pereira, Faculty of Mechanical Engineering, Pereira, Risaralda (Colombia))" data-affiliation=" (UNESP – Univ Estadual Paulista, Campus of Guaratinguetá, Department of Energy, Laboratory of Combustion and Carbon Capture LC3, CEP 12.516-410 Guaratinguetá, SP (Brazil); U.T.P. – Universidad Tecnológica de Pereira, Faculty of Mechanical Engineering, Pereira, Risaralda (Colombia))" >Rios Quiroga, Luis Carlos; 3, CEP 12.516-410 Guaratinguetá, SP (Brazil))" data-affiliation=" (UNESP – Univ Estadual Paulista, Campus of Guaratinguetá, Department of Energy, Laboratory of Combustion and Carbon Capture LC3, CEP 12.516-410 Guaratinguetá, SP (Brazil))" >Balestieri, José 3, CEP 12.516-410 Guaratinguetá, SP (Brazil))" data-affiliation=" (UNESP – Univ Estadual Paulista, Campus of Guaratinguetá, Department of Energy, Laboratory of Combustion and Carbon Capture LC3, CEP 12.516-410 Guaratinguetá, SP (Brazil))" >Antonio Perrella; 3, CEP 12.516-410 Guaratinguetá, SP (Brazil))" data-affiliation=" (UNESP – Univ Estadual Paulista, Campus of Guaratinguetá, Department of Energy, Laboratory of Combustion and Carbon Capture LC3, CEP 12.516-410 Guaratinguetá, SP (Brazil))" >Ávila, Ivonete

    2017-01-01

    Highlights: • Kinetic parameters of thermal decomposition events were obtained. • Thermal analysis was used as a tool for understanding combustion processes. • Blends would be classified using thermogravimetric analysis technics. • Synergistic effect of ethanol mixed with gasoline was studied and defined. • Relative error and activation energy values were used to analyze the synergy. - Abstract: The use of ethanol as a fuel or as an additive blended with gasoline is very important for most countries, which aim to reduce the heavy dependence on fossil fuels and mitigate greenhouse gases emission. An increased use of ethanol-gasoline blends has placed great relevance on acquiring knowledge about their physical and chemical properties. Thus, knowledge of such properties favors a better understanding of the effect of the percentage of ethanol/gasoline blends on engine performance. Thence, the present study has established a correlation between activation energy and synergetic effects, obtained by a thermal analysis, and ethanol content in gasoline for different blends in order to use this technique as a tool to classify these blends in the process in order to obtain useful energy in spark ignition engines. For such a purpose, a kinetic study has been conducted through a simultaneous thermal analysis system – TGA (thermogravimetry analysis) and DTA (differential thermal analysis) by following the methodology of non-isothermal tests. Thermogravimetric tests were performed and fuel activation energies for gasoline, ethanol, and percentages of 5, 10, 15, 20, 25, 30, 50, and 75% (%v) ethanol mixed with gasoline, which was achieved by the model free kinetics. The analysis results suggest that the theoretical curves characteristics of the thermal decomposition of ethanol-gasoline blends are rather different due to their ethanol content. Furthermore, it was observed significant interactions and synergistic effects, especially regarding those with low ethanol

  4. Thermal analysis of thermo-gravimetric measurements of spent nuclear fuel oxidation rates

    International Nuclear Information System (INIS)

    Cramer, E.R.

    1997-01-01

    A detailed thermal analysis was completed of the sample temperatures in the Thermo-Gravimetric Analysis (TGA) system used to measure irradiated N Reactor fuel oxidation rates. Sample temperatures during the oxidation process did not show the increase which was postulated as a result of the exothermic reactions. The analysis shows the axial conduction of heat in the sample holder effectively removes the added heat and only a very small, i.e., <10 C, increase in temperature is calculated. A room temperature evaporation test with water showed the sample thermocouple sensitivity to be more than adequate to account for a temperature change of approximately 5 C. Therefore, measured temperatures in the TGA are within approximately 10 C of the actual sample temperatures and no adjustments to reported data to account for the heat input from the oxidation process are necessary

  5. Investigation of Thermal Behavior for Natural Fibres Reinforced Epoxy using Thermogravimetric and Differential Scanning Calorimetric Analysis

    Directory of Open Access Journals (Sweden)

    Fauzi F.A.

    2016-01-01

    Full Text Available This paper presented the research works on the investigation of the thermal behavior of the natural fibres; i.e. pineapple leaf fibre, kenaf fibre and mengkuang fibres reinforced epoxy. The thermogravimetric analysis and differential scanning calorimetric analysis were used to measure the thermal behavior of the treated and untreated pineapple, kenaf and mengkuang fibres reinforced epoxy. The samples for both analysis were subjected to maximum temperature 600°C at the heating rate of 10°C/min. The results showed that the treated fibres show higher maximum peak temperature as compared to the untreated fibres. Additionally, the glass transition temperature showed a lower value for all treated fibre. It can be concluded that investigation of thermal properties of these natural fibres could improve the utilization of natural fibre composites in various applications i.e. sports applications.

  6. Thermogravimetric investigations of vanadium complexes

    International Nuclear Information System (INIS)

    Bechmann, W.; Uhlemann, E.; Ludwig, W.

    1987-01-01

    Extensive studies on oxovanadium(IV) and (V) complexes with bidentate chelating ligands include thermogravimetric investigations. TG, DTG, and DTA data provide additional facts to redox behaviour and stability of the complexes. These data also allow a critical appreciation of the given melting temperatures. (author)

  7. Thermogravimetric Analysis and Kinetic Study on Pyrolysis of Veteri-narian Solid Waste

    Directory of Open Access Journals (Sweden)

    Andrés Felipe Rojas González

    2016-10-01

    Full Text Available Context: Institutional waste from clinical centers can be classified as those coming from health institutions dedicated to human attention and those coming from centers for animal veterinary care. The latter are mainly hazardous wastes, hence their disposal requires incineration. Most of such waste is organic, and it is possible, therefore, to take advantage of their energetic power in combustion or pyrolysis processes. This work is motivated because no literature was found on the pyrolysis kinetics veterinary waste, as this kind of studies are mainly focused on hospital waste of human health care. Method: The kinetics of pyrolysis is characterized and studied by means of thermogravimetric analysis of 6 major veterinary waste (gauze, cotton swabs, cotton, nails, hair, plastic syringes. The characterization is performed by proximate and elemental analysis, and thermogravimetric analysis. Reactivity characteristics and pyrolytic capability of wastes are established. The kinetics study on pyrolysis was carried out by determining the kinetic triplet by isoconversional Starink method. Results: It was established that the pyrolysis index increases with the heating rate and that the thermal degradation depends on the material type of the waste. Similarly, it was found that the temperature (ΔT = Tf - Ti for the thermal decomposition of veterinary waste is: ΔTnails> ΔThair > ΔTcotton swabs > ΔTgauze > ΔTcotton > ΔTplastic syringes; the activation energy is Enails> E hair > Eplastic syringes > Ecotton swabs > E gauze > Ecotton, and the reaction order is: n hair > nnails > ncotton swabs > ncotton > n gauze > n plastic syringes. Conclusions: These results suggest the possibility of using veterinary wastes for power generation, providing an alternative for sustainable energy development to cities in continuous growth, from both, energetic and environmental points of view.

  8. Thermogravimetric analysis of phase transitions in cement compositions mixed by sodium silicate solution

    Directory of Open Access Journals (Sweden)

    Fedosov Sergey Viktorovich

    2014-01-01

    Full Text Available This paper presents a study of the capability to modify cement by mechanical activation of sodium silicate water solution. Admixtures or blends of binding agents were employed for modifying concrete properties. The liquid glass is applied to protect from chemically or physically unfavorable environmental impacts, such as acidic medium and high temperature. The sodium silicate is a high-capacity setting accelerator. The increasing of the liquid glass proportion in the mix leads to the degradation of the cement paste plasticity and for this reason it is necessary to reduce the amount of liquid glass in the cement paste. The activation of dilute water solution of sodium silicate into rotary pulsating apparatus directly before tempering of the cement paste is an effective way to decrease mass fraction of liquid glass in the cement paste. The results of the combined influence of liquid glass and mechanical activation on physicochemical processes taking place in cement stone are represented in this research. Thermogravimetric analysis was used in order to study cement blends. Thermogravimetric analysis of modified cement stone assays was performed by thermo analyzer SETARAM TGA 92-24. The results of the analysis of phase transition taking place under high-temperature heating of cement stone modified by the mechanical activation of the water solution of the sodium silicate were introduced. Thermograms of cement stone assays were obtained at different hardening age. The comparison of these thermograms allows us to come to a conclusion on the formation and the retention during long time of a more dense structure of the composite matrix mixed by the mechanical activation of sodium silicate water solution. The relation between the concrete composition and its strength properties was stated. Perhaps, the capability of modified concrete to keep calcium ions in sparingly soluble hydrosilicates leads to the increase in its durability and corrosion resistance.

  9. Thermogravimetric analysis of co-combustion between microalgae and textile dyeing sludge.

    Science.gov (United States)

    Peng, Xiaowei; Ma, Xiaoqian; Xu, Zhibin

    2015-03-01

    The synergistic interaction and kinetics of microalgae, textile dyeing sludge and their blends were investigated under combustion condition by thermogravimetric analysis. The textile dyeing sludge was blended with microalgae in the range of 10-90wt.% to investigate their co-combustion behavior. Results showed that the synergistic interaction between microalgae and textile dyeing sludge improved the char catalytic effect and alkali metals melt-induced effect on the decomposition of textile dyeing sludge residue at high temperature of 530-800°C. As the heating rate increasing, the entire combustion process was delayed but the combustion intensity was enhanced. The lowest average activation energy was obtained when the percentage of microalgae was 60%, which was 227.1kJ/mol by OFW and 227.4kJ/mol by KAS, respectively. Copyright © 2015 Elsevier Ltd. All rights reserved.

  10. Characteristics and kinetic studies of Hydrilla verticillata pyrolysis via thermogravimetric analysis.

    Science.gov (United States)

    Hu, Zhiquan; Chen, Zhihua; Li, Genbao; Chen, Xiaojuan; Hu, Mian; Laghari, Mahmood; Wang, Xun; Guo, Dabin

    2015-10-01

    The pyrolysis characteristics and kinetic of Hydrilla verticillata (HV) have been investigated using non-isothermal thermogravimetric analysis. The results showed that the pyrolysis behavior of HV can be divided into two independent stages. The kinetics of Stage I was investigated using a distributed activation energy model (DAEM) with discrete 99 first-order reactions. Stage II was an independent stage which corresponds to the decomposition of calcium oxalate, whose kinetics was studied using iso-conversional method together with compensation effect and master-plots method. The activation energies ranged from 92.39 to 506.17 and 190.42 to 222.48 kJ/mol for the first and second stages respectively. Calculated data gave very good fit to the experimental data. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Acoustic emission analysis coupled with thermogravimetric experiments dedicated to high temperature corrosion studies on metallic alloys

    International Nuclear Information System (INIS)

    Serris, Eric; Al Haj, Omar; Peres, Veronique; Cournil, Michel; Kittel, Jean; Grosjean, Francois; Ropital, Francois

    2014-01-01

    High temperature corrosion of metallic alloys (like iron, nickel, zirconium alloys) can damage equipment of many industrial fields (refinery, petrochemical, nuclear..). Acoustic emission (AE) is an interesting method owing to its sensitivity and its non-destructive aspect to quantify the level of damage in use of these alloys under various environmental conditions. High temperature corrosive phenomena create stresses in the materials; the relaxation by cracks of these stresses can be recorded and analyzed using the AE system. The goal of our study is to establish an acoustic signals database which assigns the acoustic signals to the specific corrosion phenomena. For this purpose, thermogravimetric analysis (TGA) is coupled with acoustic emission (AE) devices. The oxidation of a zirconium alloy, zircaloy-4, is first studied using thermogravimetric experiment coupled to acoustic emission analysis at 900 C. An inward zirconium oxide scale, preliminary dense, then porous, grow during the isothermal isobaric step. The kinetic rate increases significantly after a kinetic transition (breakaway). This acceleration occurs with an increase of acoustic emission activity. Most of the acoustic emission bursts are recorded after the kinetic transition. Acoustic emission signals are also observed during the cooling of the sample. AE numerical treatments (using wavelet transform) completed by SEM microscopy characterizations allows us to distinguish the different populations of cracks. Metal dusting represents also a severe form of corrosive degradation of metal alloy. Iron metal dusting corrosion is studied by AE coupled with TGA at 650 C under C 4 H 10 + H 2 + He atmosphere. Acoustic emission signals are detected after a significant increase of the sample mass.

  12. Characteristics of curcumin using cyclic voltammetry, UV–vis, fluorescence and thermogravimetric analysis

    International Nuclear Information System (INIS)

    Masek, Anna; Chrzescijanska, Ewa; Zaborski, Marian

    2013-01-01

    Highlights: • Electrooxidation of curcumin was investigated with cyclic voltammetry. • The curcumin is irreversibly oxidized at the platinum electrode in anhydrous media. • Absorbance, fluorescence and thermogravimetric analysis of curcumin was studied. • The HOMO and Mapped Electron Densities were calculated using HyperChem. • Oxidation mechanism for curcumin proposed. -- Abstract: Curcumin, the yellow, primary bioactive component of turmeric, has recently received attention from chemists due its wide range of potential biological applications as an antioxidant, anti-inflammatory, and anti-carcinogenic agent. The electrochemical behaviour of curcumin at a platinum electrode has been studied by cyclic voltammetry (CV) and differential pulse voltammetry (DPV). The oxidation of curcumin is an irreversible process that proceeds in two steps in 0.1 M (C 4 H 9 ) 4 NClO 4 in acetonitrile. The process of oxidation and its kinetics have been investigated. The rate constant, electron transfer coefficient and diffusion coefficients for the electrochemical oxidation of curcumin were determined. A mechanism for the oxidation of curcumin is proposed. The data obtained are consistent with the current literature and suggest that voltammetric studies on mechanically transferred solids may be a convenient method for elucidating the electrochemical oxidation mechanisms of compounds in anhydrous media. Theoretical calculations regarding the optimization of curcumin, electronic properties like highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) were calculated using with HyperChem software by AM1 semi-empirical method. The properties of curcumin in a homogeneous environment were investigated using spectroscopic techniques and thermogravimetric analysis

  13. Thermogravimetric analysis of the co-combustion of paper mill sludge and municipal solid waste

    International Nuclear Information System (INIS)

    Hu, Shanchao; Ma, Xiaoqian; Lin, Yousheng; Yu, Zhaosheng; Fang, Shiwen

    2015-01-01

    Highlights: • Thermogravimetric analysis of paper mill sludge and municipal solid waste were studied. • The combustion of paper mill sludge could be improved by blending municipal solid waste. • There existed significant interaction during co-combustion of the blends. • The OFW and Starink methods were used to obtain the activation energy. • The average activation energy was the lowest by blending 20% municipal solid waste. - Abstract: The thermal characteristics and kinetics of paper mill sludge (PMS), municipal solid waste (MSW) and their blends in the combustion process were investigated in this study. The mass percentages of PMS in the blends were 10%, 30%, 50%, 70% and 90%, respectively. The experiments were carried out at different heating rates (10 °C/min, 20 °C/min and 30 °C/min) and the temperature ranged from room temperature to 1000 °C in a thermogravimetric simultaneous thermal analyzer. The results suggested that the ignition temperature and burnout temperature of MSW were lower than that of PMS, and the mass loss rate of MSW was larger especially at low temperatures. There were only two mass loss peaks in the differential thermogravimetry (DTG) curve, while three mass loss peaks were observed when the blending ratios of PMS were 30%, 50%, 70%. The value of the comprehensive combustion characteristic index of the blends indicated a good combustibility when the percentage of PMS (PPMS) in the blends was less than 30%. There existed certain interaction between the combustion process of PMS and MSW, especially at high temperature stage. Activation energy (E) value obtained by the Ozawa–Flynn–Wall (OFW) method and the Starink method were very consistent. When the mass percentage of PMS in the blends was 80%, the E average value attained the minimum

  14. Rapidly assessing the activation conditions and porosity of metal-organic frameworks using thermogravimetric analysis.

    Science.gov (United States)

    McDonald, Thomas M; Bloch, Eric D; Long, Jeffrey R

    2015-03-25

    A methodology utilizing a thermogravimetric analyzer to monitor propane uptake following incremental increases of the temperature is demonstrated as a means of rapidly identifying porous materials and determining the optimum activation conditions of metal-organic frameworks.

  15. Fluid selection and parametric analysis on condensation temperature and plant height for a thermogravimetric heat pump

    International Nuclear Information System (INIS)

    Najafi, Behzad; Obando Vega, Pedro; Guilizzoni, Manfredo; Rinaldi, Fabio; Arosio, Sergio

    2015-01-01

    the system, while the COP values remain in a relatively small range. - Highlights: • The required plant height with different working fluids for a thermogravimetric heat pump was determined. • A fluid selection diagram including COP and the required height for different fluids was presented. • Sensitivity analysis to study the effect of height increasing factor on COP was performed. • Sensitivity analysis to investigate the effect of condensation temperature on the COP was also carried out

  16. Thermogravimetric Analysis of Effects of High-Content Limstone Addition on Combustion Characteristics of Taixi Anthracite

    Institute of Scientific and Technical Information of China (English)

    ZHANG Hong; LI Mei; SUN Min; WEI Xian-yong

    2004-01-01

    Combustion characteristics of Taixi anthracite admixed with high content of limestone addition were investigated with thermogravimetric analysis. The results show that limestone addition has a little promoting effect on the ignition of raw coals as a whole. The addition of limestone is found to significantly accelerate the combustion and burnout of raw coals. The higher the sample mass is, the more significant the effect will be. The results also show that the change of limestone proportion between 45%-80% has little effect on ignition temperatures of coal in the blended samples. Increasing limestone content lowers the temperature corresponding to the maximum weight loss. Although higher maximum mass loss rates are observed with higher limestone content, the effect is found not ascribed to changing limestone addition, but to the decrease of absolute coal mass in the sample. The change of limestone proportion has little effect on its burnout temperature. Mechanism analysis indicates that these phenomena result mainly from improved heat conduction due to limestone addition.

  17. Pyrolysis of tyre powder using microwave thermogravimetric analysis: Effect of microwave power.

    Science.gov (United States)

    Song, Zhanlong; Yang, Yaqing; Zhou, Long; Zhao, Xiqiang; Wang, Wenlong; Mao, Yanpeng; Ma, Chunyuan

    2017-02-01

    The pyrolytic characteristics of tyre powder treated under different microwave powers (300, 500, and 700 W) were studied via microwave thermogravimetric analysis. The product yields at different power levels were studied, along with comparative analysis of microwave pyrolysis and conventional pyrolysis. The feedstock underwent preheating, intense pyrolysis, and final pyrolysis in sequence. The main and secondary weight loss peaks observed during the intense pyrolysis stage were attributed to the decomposition of natural rubbers and synthetic rubbers, respectively. The total mass loss rates, bulk temperatures, and maximum temperatures were distinctively higher at higher powers. However, the maximum mass loss rate (0.005 s -1 ), the highest yields of liquid product (53%), and the minimum yields of residual solid samples (43.83%) were obtained at 500 W. Compared with conventional pyrolysis, microwave pyrolysis exhibited significantly different behaviour with faster reaction rates, which can decrease the decomposition temperatures of both natural and synthetic rubber by approximately 110 °C-140 °C.

  18. Combustion behavior and kinetics of low-lipid microalgae via thermogravimetric analysis.

    Science.gov (United States)

    Gai, Chao; Liu, Zhengang; Han, Guanghua; Peng, Nana; Fan, Aonan

    2015-04-01

    Thermogravimetric analysis and differential thermal analysis were employed to investigate combustion characteristics of two low-lipid microalgae, Chlorella pyrenoidosa (CP) and Spirulina platensis (SP) and iso-conversional Starink approach was used to calculate the kinetic parameters in the present study. The results showed that three stages of mass loss, including dehydration, devolatilization and char oxidation, were observed during combustion of both of two low-lipid microalgae. The whole weight loss of combustion of two microalgae was both shifted to higher temperature zones with increased heating rates from 10 to 40 K/min. In the 0.1-0.9 conversion range, the apparent activation energy of CP increased first from 51.96 to 79.53 kJ/mol, then decreased to 55.59 kJ/mol. Finally, it slightly increased to 67.27 kJ/mol. In the case of SP, the apparent activation energy gradually increased from 68.51 to 91.06 kJ/mol. Copyright © 2015 Elsevier Ltd. All rights reserved.

  19. Pyrolysis and oxy-fuel combustion characteristics and kinetics of petrochemical wastewater sludge using thermogravimetric analysis.

    Science.gov (United States)

    Chen, Jianbiao; Mu, Lin; Cai, Jingcheng; Yao, Pikai; Song, Xigeng; Yin, Hongchao; Li, Aimin

    2015-12-01

    The pyrolysis and oxy-fuel combustion characteristics of petrochemical wastewater sludge (PS) were studied in air (O2/N2) and oxy-fuel (O2/CO2) atmospheres using non-isothermal thermogravimetric analysis (TGA). Pyrolysis experiments showed that the weight loss profiles were almost similar up to 1050K in both N2 and CO2 atmospheres, while further weight loss took place in CO2 atmosphere at higher temperatures due to char-CO2 gasification. Compared with 20%O2/80%N2, the drying and devolatilization stage of PS were delayed in 20%O2/80%CO2 due to the differences in properties of the diluting gases. In oxy-fuel combustion experiments, with O2 concentration increasing, characteristic temperatures decreased, while characteristic combustion rates and combustion performance indexes increased. Kinetic analysis of PS decomposition under various atmospheres was performed using Coats-Redfern approach. The results indicated that, with O2 concentration increasing, the activation energies of Step 1 almost kept constant, while the values of subsequent three steps increased. Copyright © 2015 Elsevier Ltd. All rights reserved.

  20. Friedel's salt profiles from thermogravimetric analysis and thermodynamic modelling of Portland cement-based mortars exposed to sodium chloride solution

    DEFF Research Database (Denmark)

    Shi, Zhenguo; Geiker, Mette Rica; Lothenbach, Barbara

    2017-01-01

    Thermogravimetric analysis (TGA), powder X-ray diffraction (XRD) and thermodynamic modelling have been used to obtain Friedel's salt profiles for saturated mortar cylinders exposed to a 2.8 M NaCl solution. Comparison of the measured Friedel's salt profiles with the total chloride profiles...

  1. Pyrolysis behaviors and kinetic studies on Eucalyptus residues using thermogravimetric analysis

    International Nuclear Information System (INIS)

    Chen, Zhihua; Zhu, Quanjie; Wang, Xun; Xiao, Bo; Liu, Shiming

    2015-01-01

    Highlights: • The first study on pyrolysis characteristics and kinetic of Eucalyptus residues. • Pyrolysis process can be divided into three stages using differential DTG method. • A new modified discrete DAEM showed better than Gaussian DAEM for kinetic studies. • Variations of activation energy reveal the mechanism change during pyrolysis process. - Abstract: The pyrolysis behaviors and kinetics of Eucalyptus leaves (EL), Eucalyptus bark (EB) and Eucalyptus sawdust (ESD) were investigated by using thermogravimetric analysis (TGA) technique. Three stages for EL, EB and ESD pyrolysis have been divided using differential derivative thermogravimetric (DDTG) method and the second stage is the main pyrolysis process with approximately 86.93% (EL), 88.96% (EB) and 97.84% (ESD) weight loss percentages. Kinetic parameters of Gaussian distributed activation energy model (DAEM) for EL, EB and ESD pyrolysis are: distributed centers (E_0) of 141.15 kJ/mol (EL), 149.21 kJ/mol (EB), 175.79 kJ/mol (ESD), standard deviations (σ) of 18.35 kJ/mol (EL), 18.37 kJ/mol (EB), 14.41 kJ/mol (ESD) and pre-exponential factors (A) of 1.15E+10 s"−"1 (EL), 4.34E+10 s"−"1 (EB), 7.44E+12 s"−"1 (ESD). A new modified discrete DAEM was performed and showed excellent fits to experimental data than Gaussian DAEM. According to the modified discrete DAEM, the activation energies are in ranges of 122.67–308.64 kJ/mol, 118.72–410.80 kJ/mol and 108.39–192.93 kJ/mol for EL, EB and ESD pyrolysis, respectively. The pre-exponential factors of discrete DAEM have wide ranges of 4.84E+13–6.12E+22 s"−"1 (EL), 1.91E+12–4.51E+25 s"−"1 (EB) and 63.43–4.36E+11 s"−"1 (ESD). The variation of activation energy versus conversion reveals the mechanism change during pyrolysis process. The kinetic data would be of immense benefit to model, design and develop suitable thermo-chemical systems for the application of Eucalyptus residues.

  2. Pyrolysis kinetics investigation of Malaysian based biomass with non-isothermal thermogravimetric analysis (TGA)

    International Nuclear Information System (INIS)

    Seyed Shahabeddin Nehzati; Dayang Radiah Awang Biak; Wan Azlina Wan Abdul Karim Ghani; Mohd Amran Mohd Salleh

    2010-01-01

    Full text: Biomass is currently being used as a sustainable energy source. Otherwise the scarceness of fossil fuel sources and the demand for environmental responsibility force the industries to use biomass as an alternate source of energy. Pyrolysis is the first step of biomass conversion and well understanding of this process can develop the biomass conversion such as gasification, liquefaction, carbonization and combustion .TGA studies of Malaysian based biomass have been carried out. TGA studies provide important insight on the thermochemical behavior of specific solid waste. The results of non-isothermal thermogravimetric analysis of palm kernel shell, coconut shell and bagasse, carried out at heating rates of 10 degree Celsius/ min, 20 degree Celsius/ min and 50 degree Celsius/ min, to ramp the temperature from 30 to 1000 were analysed. The TGA studies were carried out in an inert atmosphere of nitrogen. Arrhenius parameters were estimated by 3 different models namely Kissinger model, three-pseudo component and DEAM model the estimated values and the models were compared. The results show that the three-pseudo component model has a good agreement with the experimental results, indicating that ligno celluloses components in the mixture behave in the same way as they do separately. Also it is seen that the decomposition process shifts to higher temperatures at higher heating rates as a result of the competing effects of heat and mass transfer to the material. (Author)

  3. Thermogravimetric Analysis (TGA) Profile of Modified Sba-15 at Different Amount of Alkoxy silane Group

    International Nuclear Information System (INIS)

    Norhasyimi Rahmat; Nur Fathilah Mohd Yusof; Ezani Hafiza

    2014-01-01

    This study focused on meso porous silica SBA-15 modified with alkoxy silane functional group; phenyltriethoxysilane (PTES) and vinyltriethoxysilane (VTES) using direct synthesis and post-grafting methods. By direct synthesis method, SBA-15 template by triblock copolymer (P123) and functionalized with alkoxy silane groups at different amount of loadings were co-condensed with tetraethyl orthosilicate (TEOS) under acidic conditions. As for post-grafting method, different loadings of alkoxy silane groups were added after co-condensation of TEOS with P123 template. Both synthesis methods used calcination process to remove surfactant template at 550 degree Celsius for 5 hours. The derivatized SBA-15 was characterized by thermogravimetric analysis to evaluate the profile at different loadings of alkoxy silane groups with different synthesis method. At temperature range of 300-800 degree Celsius, post-grafting method displayed the highest weight loss of phenyl and vinyl groups. However, there was no significant difference of weight loss for different amount of organo silane groups. In this study, TGA has shown to be significant characterization means to determine the effects of different method used in synthesizing modified SBA-15. It was shown that different loading of phenyl and vinyl groups did not affect the efficiency of surfactant removal. (author)

  4. Pyrolysis kinetics and thermal behavior of waste sawdust biomass using thermogravimetric analysis.

    Science.gov (United States)

    Mishra, Ranjeet Kumar; Mohanty, Kaustubha

    2018-03-01

    The present study reports pyrolysis behavior of three waste biomass using thermogravimetric analysis to determine kinetic parameters at five different heating rates. Physiochemical characterization confirmed that these biomass have the potential for fuel and energy production. Pyrolysis experiments were carried out at five different heating rates (5-25 °C min -1 ). Five model-free methods such as Kissinger-Akahira-Sunose (KAS), Ozawa-Flynn-Wall (OFW), Friedman, Coats-Redfern, and distributed activation energy (DAEM) were used to calculate the kinetic parameters. The activation energy was found to be 171.66 kJ mol -1 , 148.44 kJ mol -1 , and 171.24 kJ mol -1 from KAS model; 179.29 kJ mol -1 , 156.58 kJ mol -1 , and 179.47 kJ mol -1 from OFW model; 168.58 kJ mol -1 , 181.53 kJ mol -1 , and 184.61 kJ mol -1 from Friedman model; and 206.62 kJ mol -1 , 171.63 kJ mol -1 , and 160.45 kJ mol -1 from DAEM model for PW, SW, AN biomass respectively. The calculated kinetic parameters are in good agreement with other reported biomass. Copyright © 2017 Elsevier Ltd. All rights reserved.

  5. A Combined Raman Spectroscopic and Thermogravimetric Analysis Study on Oxidation of Coal with Different Ranks

    Directory of Open Access Journals (Sweden)

    Weiqing Zhang

    2015-01-01

    Full Text Available Raman spectroscopy and nonisothermal thermogravimetric analysis (TGA measurements have been reported for different rank coals (lignite, bituminous coal, and anthracite and the relationship between the measurements was examined. It was found that the Raman spectra parameters can be used to characterize structure changes in the different rank coals, such as the band area ratios based on the curve-fitted results. Higher ranked coal was found to have higher values of IGR/IAll and IG+GR/IAll but lower values of ID/I(G+GR, IDL/I(G+GR, IS+SL/I(G+GR, and I(GL+GL'/I(G+GR. The oxidation properties of the coal samples were characterized by the reactivity indexes Tig, T20%, and Tmax from TGA data which were found to correlate well with the band area ratios of IGR/IAll, IG+GR/IAll, and IS+SL/I(G+GR. Based on these correlations, the Raman band area ratios were found to correlate with the oxidation activity of coal providing additional structural information which can be used to understand the changes in the TGA measurements.

  6. Determination of activation energy for animal fat and crude glycerol using thermogravimetric analysis

    Energy Technology Data Exchange (ETDEWEB)

    Koch, Crhristoph [University of Hannover, Hannover (Germany); Mortari, Daniela; Avila, Ivonete; Santos, Antonio Moreira dos; Silva, Mario Lucio Cristovam; Crnkovic, Paula Manoel [University of Sao Paulo, Sao Carlos, SP (Brazil)], e-mails: iavila@sc.usp.br, asantos@sc.usp.br, paulam@sc.usp.br

    2010-07-01

    The present study deals with the determination of the activation energy of animal fat and crude glycerol from a biodiesel production plant. The activation energies were investigated by thermogravimetric analysis in the temperature range of {delta}T = 25-600 deg C. The transient experiments were run for every sample (10 mg) at five different heating rates (2.5, 5.0, 10.0, 20.0 and 30.0 deg C/min) in atmosphere of synthetic air. It is possible to establish a direct relation between the activation energy and the ignition delay, which characterizes the combustion quality of a fuel. The activation energy could be determined as a function of the conversion degree and the temperature by the isoconversional model free kinetics. Four distinct phases were found for each sample and one of these phases was identified as low-temperature oxidation (LTO). As this region is responsible for the first vaporization of the fuel, the activation energies were determined for this special region along the whole conversion range (0 - 100 %). The following mean values could be determined: animal fat = 108.87 +- 52.28 kJ/mol, and crude glycerol = 65.37+- 13.17 kJ/mol. From these data, it was possible to conclude that animal fat is the most complex sample between the ones studied in this work (author)

  7. Oxy-fuel combustion characteristics and kinetics of microalgae Chlorella vulgaris by thermogravimetric analysis.

    Science.gov (United States)

    Chen, Chunxiang; Lu, Ziguang; Ma, Xiaoqian; Long, Jun; Peng, Yuning; Hu, Likun; Lu, Quan

    2013-09-01

    Oxy-fuel or O2/CO2 combustion technology was used to investigate the combustion of Chlorella vulgaris by thermogravimetric analysis (TGA). Oxy-fuel combustion occurs in an O2/CO2 atmosphere instead of an O2/N2 atmosphere and offers an alternative method of C. vulgaris preparation for biofuels processing. Our results show that three stages were observed during C. vulgaris combustion and the main combustion process occurred at the second stage. Compared with a 20%O2/80%N2 atmosphere, the mass loss rate at the DTG peaks (Rp) and the average reaction rate (Rv) in a 20%O2/80%CO2 atmosphere was lower, while the ignition temperature (TI) was higher. As oxygen concentration increases in an O2/CO2 atmosphere, Rp, Rv and the apparent activation energy (E) increases, while TI, the final temperature detected as mass stabilization (Tf) and the residue mass (Mr) decreases; As the heating rate (β) increases, TI, Tf and Rp increase, while Mr decreases. Crown Copyright © 2013. Published by Elsevier Ltd. All rights reserved.

  8. A Combined Raman Spectroscopic and Thermogravimetric Analysis Study on Oxidation of Coal with Different Ranks.

    Science.gov (United States)

    Zhang, Weiqing; Jiang, Shuguang; Hardacre, Christopher; Goodrich, Peter; Wang, Kai; Shao, Hao; Wu, Zhengyan

    2015-01-01

    Raman spectroscopy and nonisothermal thermogravimetric analysis (TGA) measurements have been reported for different rank coals (lignite, bituminous coal, and anthracite) and the relationship between the measurements was examined. It was found that the Raman spectra parameters can be used to characterize structure changes in the different rank coals, such as the band area ratios based on the curve-fitted results. Higher ranked coal was found to have higher values of I GR/I All and I (G + GR)/I All but lower values of I D/I (G+GR), I DL/I (G+GR), I (S + SL)/I (G+GR), and I (GL+GL')/I (G+GR). The oxidation properties of the coal samples were characterized by the reactivity indexes T ig, T 20%, and T max from TGA data which were found to correlate well with the band area ratios of I GR/I All, I (G + GR)/I All, and I (S + SL)/I (G+GR). Based on these correlations, the Raman band area ratios were found to correlate with the oxidation activity of coal providing additional structural information which can be used to understand the changes in the TGA measurements.

  9. Pyrolysis kinetics of raw and hydrothermally carbonized Karanj (Pongamia pinnata) fruit hulls via thermogravimetric analysis.

    Science.gov (United States)

    Islam, Md Azharul; Asif, M; Hameed, B H

    2015-03-01

    The pyrolysis of karanj fruit hulls (KFH) and karanj fruit hull hydrothermal carbonization (KFH-HTC) hydrochar was thermogravimetrically investigated under a nitrogen environment at 5 °C/min, 10 °C/min, and 20 °C/min. The pyrolysis decomposition of KFH biomass was faster than that of KFH-HTC hydrochar because of the high volatility and fixed carbon of KFH biomass. Weight loss percentage was also affected by the heating rates. The kinetic data were evaluated with the Kissinger-Akahira-Sunose and Flynn-Wall-Ozawa methods. The activation energy values obtained with these two methods were 61.06 and 68.53 kJ/mol for KFH biomass and 130.49 and 135.87 kJ/mol for KFH-HTC hydrochar, respectively. The analysis of kinetic process mechanisms was verified with the Coats-Redfern method. KFH-HTC hydrochar may play a potential role in transforming biomass to energy-rich feedstock for thermochemical applications because of its high heating value, high fixed carbon, and low ash and sulfur contents. Copyright © 2014 Elsevier Ltd. All rights reserved.

  10. Characteristics and kinetic study on pyrolysis of five lignocellulosic biomass via thermogravimetric analysis.

    Science.gov (United States)

    Chen, Zhihua; Hu, Mian; Zhu, Xiaolei; Guo, Dabin; Liu, Shiming; Hu, Zhiquan; Xiao, Bo; Wang, Jingbo; Laghari, Mahmood

    2015-09-01

    Pyrolysis characteristics and kinetic of five lignocellulosic biomass pine wood sawdust, fern (Dicranopteris linearis) stem, wheat stalk, sugarcane bagasse and jute (Corchorus capsularis) stick were investigated using thermogravimetric analysis. The pyrolysis of five lignocellulosic biomass could be divided into three stages, which correspond to the pyrolysis of hemicellulose, cellulose and lignin, respectively. Single Gaussian activation energy distributions of each stage are 148.50-201.13 kJ/mol with standard deviations of 2.60-13.37 kJ/mol. The kinetic parameters of different stages were used as initial guess values for three-parallel-DAEM model calculation with good fitting quality and fast convergence rate. The mean activation energy ranges of hemicellulose, cellulose and lignin were 148.12-164.56 kJ/mol, 171.04-179.54 kJ/mol and 175.71-201.60 kJ/mol, with standard deviations of 3.91-9.89, 0.29-1.34 and 23.22-27.24 kJ/mol, respectively. The mass fractions of hemicellulose, cellulose and lignin in lignocellulosic biomass were respectively estimated as 0.12-0.22, 0.54-0.65 and 0.17-0.29. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Thermogravimetric analysis of rice and wheat straw catalytic combustion in air- and oxygen-enriched atmospheres

    International Nuclear Information System (INIS)

    Yu Zhaosheng; Ma Xiaoqian; Liu Ao

    2009-01-01

    By thermogravimetric analysis (TGA) study, the influences of different catalysts on the ignition and combustion of rice and wheat straw in air- and oxygen-enriched atmospheres have been investigated in this paper. Straw combustion is divided into two stages. One is the emission and combustion of volatiles and the second is the combustion of fixed carbon. The existence of catalysts in the first step enhances the emission of volatiles from the straw. The action of catalysts in the second step of straw combustion may be as a carrier of oxygen to the fixed carbon. Two parameters have been used to compare the characteristics of ignition and combustion of straw under different catalysts and in various oxygen concentrations. One is the temperature when the conversion degree combustible (CDC) of straw is 5%, the other is the CDC when the temperature is 900 deg. C. By comparing the different values of the two parameters, the different influences of the catalysts and oxygen concentration on the ignition and combustion of straw have been studied, the action of these catalysts for straw ignition and combustion in air and oxygen-enriched atmosphere is effective except the oxygen-enriched catalytic combustion of wheat straw fixed carbon

  12. Thermal Behaviour of Five Different Date Palm Residues of Algeria by Thermogravimetric Analysis

    Directory of Open Access Journals (Sweden)

    Siham AMIROU

    2013-06-01

    Full Text Available Renewable energy has become moreimportant globally especially with the current fuel andeconomic crisis. Date palm biomasses are highlypotential materials for energy resources. The factthat they are renewable and abundantly availableare amongst the attractive reasons of employingthem as the major source for renewable energy. Thepurpose of this research was to investigate thethermal behavior of date palm biomass in order toevaluate their usefulness for energy production. Inmicroparticular scale, the thermogravimetric analysis(TGA is one of the techniques used to determinethe thermal properties of five different date palmresidues that were studied: (date palm rachis (DPR,date palm trunk (DPT, leaf base (Petiole (LB,fruitstalk prunings (FP and liff (LP. The TGAtechnique consists to record the lost weight duringthe increase in temperature from 20°C until 600°Cwith a 10°C/min heating rate. The thermogramspresented a departure phase of free water (fromroom temperature to 110°C before the degradationprocess of the lignocellulosic constituents. The ligninand hemicellulose play an important role on thedegradation of lignocellulosic materials at thetemperature under 250°C. The degradation ofcellulose begins at 250°C and overlaps to that oflignin until 450°C.

  13. Thermogravimetric analysis and kinetic study of formation of lithium titanate by solid state route

    International Nuclear Information System (INIS)

    Sonak, Sagar; Jain, Uttam; Sahu, Ashok Kumar; Kumar, Sanjay; Krishnamurthy, Nagaiyar

    2015-01-01

    The kinetics of formation of lithium titanate from the solid state reaction of lithium carbonate and titanium oxide was studied using non-isothermal thermogravimetric technique. Thermogravimetric data for the reaction of lithium carbonate and titanium oxide was obtained at various heating rates. The methods such as Flynn–Wall–Ozawa and Kissinger–Akahira–Sunose were used to estimate the kinetic parameters from the obtained thermogravimetric data. The average activation energy for the formation of lithium titanate by solid state route was found to be 243 kJ/mol K. The reaction mechanism was determined by the method given by Malek. It was found that the three dimensional diffusion model best describes the reaction kinetics. A kinetic equation describing the reaction is proposed and reaction mechanism is discussed

  14. Investigation of thermodynamic properties of magnesium chloride amines by HPDSC and TG. For application in a high-lift high-temperature chemical heat pump

    NARCIS (Netherlands)

    Bevers, E.R.T.; Oonk, H.A.J.; Haije, W.G.; Ekeren, P.J. van

    2007-01-01

    The formation as well as the decomposition of magnesium chloride ammonia complexes was studied by high-pressure differential scanning calorimetry (HPDSC) and thermogravimetric analysis (TG). HPDSC runs were performed under constant ammonia pressure conditions to determine the transition temperatures

  15. Thermal and Chemical Characterization of Non-Metallic Materials Using Coupled Thermogravimetric Analysis and Infrared Spectroscopy

    Science.gov (United States)

    Huff, Timothy L.

    2002-01-01

    Thermogravimetric analysis (TGA) is widely employed in the thermal characterization of non-metallic materials, yielding valuable information on decomposition characteristics of a sample over a wide temperature range. However, a potential wealth of chemical information is lost during the process, with the evolving gases generated during thermal decomposition escaping through the exhaust line. Fourier Transform-Infrared spectroscopy (FT-IR) is a powerful analytical technique for determining many chemical constituents while in any material state, in this application, the gas phase. By linking these two techniques, evolving gases generated during the TGA process are directed into an appropriately equipped infrared spectrometer for chemical speciation. Consequently, both thermal decomposition and chemical characterization of a material may be obtained in a single sample run. In practice, a heated transfer line is employed to connect the two instruments while a purge gas stream directs the evolving gases into the FT-IR. The purge gas can be either high purity air or an inert gas such as nitrogen to allow oxidative and pyrolytic processes to be examined, respectively. The FT-IR data is collected realtime, allowing continuous monitoring of chemical compositional changes over the course of thermal decomposition. Using this coupled technique, an array of diverse materials has been examined, including composites, plastics, rubber, fiberglass epoxy resins, polycarbonates, silicones, lubricants and fluorocarbon materials. The benefit of combining these two methodologies is of particular importance in the aerospace community, where newly developing materials have little available data with which to refer. By providing both thermal and chemical data simultaneously, a more definitive and comprehensive characterization of the material is possible. Additionally, this procedure has been found to be a viable screening technique for certain materials, with the generated data useful in

  16. Combustion characteristics of Malaysian oil palm biomass, sub-bituminous coal and their respective blends via thermogravimetric analysis (TGA).

    Science.gov (United States)

    Idris, Siti Shawalliah; Rahman, Norazah Abd; Ismail, Khudzir

    2012-11-01

    The combustion characteristics of Malaysia oil palm biomass (palm kernel shell (PKS), palm mesocarp fibre (PMF) and empty fruit bunches (EFB)), sub-bituminous coal (Mukah Balingian) and coal/biomass blends via thermogravimetric analysis (TGA) were investigated. Six weight ratios of coal/biomass blends were prepared and oxidised under dynamic conditions from temperature 25 to 1100°C at four heating rates. The thermogravimetric analysis demonstrated that the EFB and PKS evolved additional peak besides drying, devolatilisation and char oxidation steps during combustion. Ignition and burn out temperatures of blends were improved in comparison to coal. No interactions were observed between the coal and biomass during combustion. The apparent activation energy during this process was evaluated using iso-conversional model free kinetics which resulted in highest activation energy during combustion of PKS followed by PMF, EFB and MB coal. Blending oil palm biomass with coal reduces the apparent activation energy value. Copyright © 2012 Elsevier Ltd. All rights reserved.

  17. Thermogravimetric analysis of silicon carbide-silicon nitride polycarbosilazane precursor during pyrolysis from ambient to 1000 C

    Science.gov (United States)

    Ledbetter, F. E., III; Daniels, J. G.; Clemons, J. M.; Hundley, N. H.; Penn, B. G.

    1984-01-01

    Thermogravimetric analysis data are presented on the unmeltable polycarbosilazane precursor of silicon carbide-silicon nitride fibers, over the room temperature-1000 C range in a nitrogen atmosphere, in order to establish the weight loss at various temperatures during the precursor's pyrolysis to the fiber material. The fibers obtained by this method are excellent candidates for use in applications where the oxidation of carbon fibers (above 400 C) renders them unsuitable.

  18. Quantitative detection of powdered activated carbon in wastewater treatment plant effluent by thermogravimetric analysis (TGA).

    Science.gov (United States)

    Krahnstöver, Therese; Plattner, Julia; Wintgens, Thomas

    2016-09-15

    For the elimination of potentially harmful micropollutants, powdered activated carbon (PAC) adsorption is applied in many wastewater treatment plants (WWTP). This holds the risk of PAC leakage into the WWTP effluent and desorption of contaminants into natural water bodies. In order to assess a potential PAC leakage, PAC concentrations below several mg/L have to be detected in the WWTP effluent. None of the methods that are used for water analysis today are able to differentiate between activated carbon and solid background matrix. Thus, a selective, quantitative and easily applicable method is still needed for the detection of PAC residues in wastewater. In the present study, a method was developed to quantitatively measure the PAC content in wastewater by using filtration and thermogravimetric analysis (TGA), which is a well-established technique for the distinction between different solid materials. For the sample filtration, quartz filters with a temperature stability up to 950 °C were used. This allowed for sensitive and well reproducible measurements, as the TGA was not affected by the presence of the filter. The sample's mass fractions were calculated by integrating the mass decrease rate obtained by TGA in specific, clearly identifiable peak areas. A two-step TGA heating method consisting of N2 and O2 atmospheres led to a good differentiation between PAC and biological background matrix, thanks to the reduction of peak overlapping. A linear correlation was found between a sample's PAC content and the corresponding peak areas under N2 and O2, the sample volume and the solid mass separated by filtration. Based on these findings, various wastewater samples from different WWTPs were then analyzed by TGA with regard to their PAC content. It was found that, compared to alternative techniques such as measurement of turbidity or total suspended solids, the newly developed TGA method allows for a quantitative and selective detection of PAC concentrations down to 0

  19. Thermogravimetric analysis and kinetic modeling of low-transition-temperature mixtures pretreated oil palm empty fruit bunch for possible maximum yield of pyrolysis oil.

    Science.gov (United States)

    Yiin, Chung Loong; Yusup, Suzana; Quitain, Armando T; Uemura, Yoshimitsu; Sasaki, Mitsuru; Kida, Tetsuya

    2018-05-01

    The impacts of low-transition-temperature mixtures (LTTMs) pretreatment on thermal decomposition and kinetics of empty fruit bunch (EFB) were investigated by thermogravimetric analysis. EFB was pretreated with the LTTMs under different duration of pretreatment which enabled various degrees of alteration to their structure. The TG-DTG curves showed that LTTMs pretreatment on EFB shifted the temperature and rate of decomposition to higher values. The EFB pretreated with sucrose and choline chloride-based LTTMs had attained the highest mass loss of volatile matter (78.69% and 75.71%) after 18 h of pretreatment. For monosodium glutamate-based LTTMs, the 24 h pretreated EFB had achieved the maximum mass loss (76.1%). Based on the Coats-Redfern integral method, the LTTMs pretreatment led to an increase in activation energy of the thermal decomposition of EFB from 80.00 to 82.82-94.80 kJ/mol. The activation energy was mainly affected by the demineralization and alteration in cellulose crystallinity after LTTMs pretreatment. Copyright © 2018 Elsevier Ltd. All rights reserved.

  20. Investigation of co-combustion characteristics of sewage sludge and coffee grounds mixtures using thermogravimetric analysis coupled to artificial neural networks modeling.

    Science.gov (United States)

    Chen, Jiacong; Liu, Jingyong; He, Yao; Huang, Limao; Sun, Shuiyu; Sun, Jian; Chang, KenLin; Kuo, Jiahong; Huang, Shaosong; Ning, Xunan

    2017-02-01

    Artificial neural network (ANN) modeling was applied to thermal data obtained by non-isothermal thermogravimetric analysis (TGA) from room temperature to 1000°C at three different heating rates in air to predict the TG curves of sewage sludge (SS) and coffee grounds (CG) mixtures. A good agreement between experimental and predicted data verified the accuracy of the ANN approach. The results of co-combustion showed that there were interactions between SS and CG, and the impacts were mostly positive. With the addition of CG, the mass loss rate and the reactivity of SS were increased while charring was reduced. Measured activation energies (E a ) determined by the Kissinger-Akahira-Sunose (KAS) and Ozawa-Flynn-Wall (OFW) methods deviated by <5%. The average value of E a (166.8kJ/mol by KAS and 168.8kJ/mol by OFW, respectively) was the lowest when the fraction of CG in the mixture was 40%. Copyright © 2016 Elsevier Ltd. All rights reserved.

  1. Water desorption of cassava starch granules: A study based on thermogravimetric analysis of aqueous suspensions and humid powders.

    Science.gov (United States)

    Ayala Valencia, Germán; Djabourov, Madeleine; do Amaral Sobral, Paulo José

    2016-08-20

    This work reports on water desorption from cassava starch in relation with the structure and conditioning of granules in suspensions or after equilibration in desiccators. The experimental work is performed by thermogravimetric analysis with isothermal and non-isothermal protocols and interpreted to derive the activation energies and desorption frequencies according to the humidity range with no adjustable parameter. The analysis points out the different types of water interacting with the starch granules and relates the drying coefficients to their microscopic structure. The work helps clarifying contradictory and partial results from the literature. Copyright © 2016 Elsevier Ltd. All rights reserved.

  2. Modelization of nanospace interaction involving a ferromagnetic atom: a spin polarization effect study by thermogravimetric analysis.

    Science.gov (United States)

    Santhanam, K S V; Chen, Xu; Gupta, S

    2014-04-01

    Ab initio studies of ferromagnetic atom interacting with carbon nanotubes have been reported in the literature that predict when the interaction is strong, a higher hybridization with confinement effect will result in spin polarization in the ferromagnetic atom. The spin polarization effect on the thermal oxidation to form its oxide is modeled here for the ferromagnetic atom and its alloy, as the above studies predict the 4s electrons are polarized in the atom. The four models developed here provide a pathway for distinguishing the type of interaction that exists in the real system. The extent of spin polarization in the ferromagnetic atom has been examined by varying the amount of carbon nanotubes in the composites in the thermogravimetric experiments. In this study we report the experimental results on the CoNi alloy which appears to show selective spin polarization. The products of the thermal oxidation has been analyzed by Fourier Transform Infrared Spectroscopy.

  3. Nonisothermal Thermogravimetric Analysis of Thai Lignite with High CaO Content

    Science.gov (United States)

    Pintana, Pakamon

    2013-01-01

    Thermal behaviors and combustion kinetics of Thai lignite with different SO3-free CaO contents were investigated. Nonisothermal thermogravimetric method was carried out under oxygen environment at heating rates of 10, 30, and 50°C min−1 from ambient up to 1300°C. Flynn-Wall-Ozawa (FWO) and Kissinger-Akahira-Sunose (KAS) methods were adopted to estimate the apparent activation energy (E) for the thermal decomposition of these coals. Different thermal degradation behaviors were observed in lignites with low (14%) and high (42%) CaO content. Activation energy of the lignite combustion was found to vary with the conversion fraction. In comparison with the KAS method, higher E values were obtained by the FWO method for all conversions considered. High CaO lignite was observed to have higher activation energy than the low CaO coal. PMID:24250259

  4. Kinetic analysis of thermogravimetric data of thorium-all-cis-1,2,3,4-cyclopentanetetracarboxylic acid complex

    International Nuclear Information System (INIS)

    Ramarao, G.A.; Nair, P.K.R.; Srinivasulu, K.

    1979-01-01

    Thorium (IV) forms 1:1 complex with all-cis-1,2,3,4-cyclopentanetetracarboxylic acid (CPTA). Thermogravimetric analysis indicated that it undergoes primarily a two step decomposition of one corresponding to loss of water and another to the decomposition of the complex. Apparent activation energy, frequency factor and activation entropy were determined. Using the experimental data, the reaction order and activation energy were calculated by Freeman-Carroll method and also by Doyle method as modified by J. Zsako, by calculation of standard deviation instead of curve fitting method. (author)

  5. Thermogravimetric study and kinetic analysis of fungal pretreated corn stover using the distributed activation energy model.

    Science.gov (United States)

    Ma, Fuying; Zeng, Yelin; Wang, Jinjin; Yang, Yang; Yang, Xuewei; Zhang, Xiaoyu

    2013-01-01

    Non-isothermal thermogravimetry/derivative thermogravimetry (TG/DTG) measurements are used to determine pyrolytic characteristics and kinetics of lignocellulose. TG/DTG experiments at different heating rates with corn stover pretreated with monocultures of Irpex lacteus CD2 and Auricularia polytricha AP and their cocultures were conducted. Heating rates had little effect on the pyrolysis process, but the peak of weight loss rate in the DTG curves shifted towards higher temperature with heating rate. The maximum weight loss of biopretreated samples was 1.25-fold higher than that of the control at the three heating rates, and the maximum weight loss rate of the co-culture pretreated samples was intermediate between that of the two mono-cultures. The activation energies of the co-culture pretreated samples were 16-72 kJ mol(-1) lower than that of the mono-culture at the conversion rate range from 10% to 60%. This suggests that co-culture pretreatment can decrease activation energy and accelerate pyrolysis reaction thus reducing energy consumption. Copyright © 2012 Elsevier Ltd. All rights reserved.

  6. Thermogravimetric analysis for rapid assessment of moisture diffusivity in polydisperse powder and thin film matrices.

    Science.gov (United States)

    Thirunathan, Praveena; Arnz, Patrik; Husny, Joeska; Gianfrancesco, Alessandro; Perdana, Jimmy

    2018-03-01

    Accurate description of moisture diffusivity is key to precisely understand and predict moisture transfer behaviour in a matrix. Unfortunately, measuring moisture diffusivity is not trivial, especially at low moisture values and/or elevated temperatures. This paper presents a novel experimental procedure to accurately measure moisture diffusivity based on thermogravimetric approach. The procedure is capable to measure diffusivity even at elevated temperatures (>70°C) and low moisture values (>1%). Diffusivity was extracted from experimental data based on "regular regime approach". The approach was tailored to determine diffusivity from thin film and from poly-dispersed powdered samples. Subsequently, measured diffusivity was validated by comparing to available literature data, showing good agreement. Ability of this approach to accurately measure diffusivity at a wider range of temperatures provides better insight on temperature dependency of diffusivity. Thus, this approach can be crucial to ensure good accuracy of moisture transfer description/prediction especially when involving elevated temperatures. Copyright © 2017 Elsevier Ltd. All rights reserved.

  7. Thermogravimetric and kinetic analysis of thermal decomposition characteristics of low-lipid microalgae.

    Science.gov (United States)

    Gai, Chao; Zhang, Yuanhui; Chen, Wan-Ting; Zhang, Peng; Dong, Yuping

    2013-12-01

    The thermal decomposition behavior of two microalgae, Chlorella pyrenoidosa (CP) and Spirulina platensis (SP), were investigated on a thermogravimetric analyzer under non-isothermal conditions. Iso-conversional Vyazovkin approach was used to calculate the kinetic parameters, and the universal integral method was applied to evaluate the most probable mechanisms for thermal degradation of the two feedstocks. The differential equations deduced from the models were compared with experimental data. For the range of conversion fraction investigated (20-80%), the thermal decomposition process of CP could be described by the reaction order model (F3), which can be calculated by the integral equation of G(α) = [(1 - α)(-2) - 1]/2. And the apparent activation energy was in the range of 58.85-114.5 kJ/mol. As for SP, it can be described by the reaction order model (F2), which can be calculated by the integral equation of G(α) = (1 - α)(-1) - 1, and the range of apparent activation energy was 74.35-140.1 kJ/mol. Copyright © 2013 Elsevier Ltd. All rights reserved.

  8. Determination of kinetic parameters of Phlomis bovei de Noé using thermogravimetric analysis.

    Science.gov (United States)

    Yahiaoui, Meriem; Hadoun, Hocine; Toumert, Idir; Hassani, Aicha

    2015-11-01

    This paper reports the pyrolysis study of Phlomis bovei biomass by thermogravimetric experiments in order to determine the thermal degradation behavior and kinetic parameters. The weight losses were found to occur in three stages. In the DTG thermograms, an increase of the heating rate tended to delay thermal degradation processes towards higher temperatures. The average values of activation energy and pre-exponential factor calculated from Ozawa-Flynn-Wall, Kissinger-Akahira-Sunose and Kissinger methods are 134.83, 134.06, 223.31kJ/mol and 4.1610(13), 1.1810(10), 2.8110(11)/s, respectively. The three-pseudo-component method shows that the activation energy increases with increasing the heating rate for hemicellulose and cellulose while the activation energy of the lignin decreased with an increase of the heating rate. Predicted results and experimental data exhibit similar tendencies and the three pseudo-components model with n different from unity 1 is recommended as the most suitable for prediction of kinetic behavior of Phlomis bovei de Noé. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. Thermogravimetric Analysis of Rice Husk and Coconut Pulp for Potential Bio fuel Production by Flash Pyrolysis

    International Nuclear Information System (INIS)

    Noorhaza Alias; Norazana Ibrahim; Mohd Kamaruddin Abdul Hamid

    2014-01-01

    The purpose of this paper is to study the characteristics and thermal degradation behavior of rice husk and coconut pulp for bio fuel production via flash pyrolysis technology. The elemental properties of the feedstock were characterized by an elemental analyzer while thermal properties were investigated using thermogravimetric analyzer (TGA). The pyrolysis processes were carried out at room temperature up to 700 degree Celsius in the presence of nitrogen gas flowing at 150 ml/ min. The investigated parameters are particle sizes and heating rates. The particle sizes varied in the range of dp 1 < 0.30 mm and 0.30= dp 2 <0.50 mm. The heating rates applied were 50 degree Celsius/ min and 80 degree Celsius/ min. It was shown smaller particle size produces 2.11-3.59 % less volatile product when pyrolyzed at 50 degree Celsius/ min compared to 80 degree Celsius/ min. Higher heating rates causes biomass degrades in a narrow temperature range by 25 degree Celsius. It also increases the maximum peak rate by 0.01 mg/ s for rice husk at dp 1 and 0.02 mg/ s at dp 2 . In case of coconut pulp, the change is not significant for dp 1 but for dp 2 a 0.02 mg/ s changes was recorded. (author)

  10. Thermogravimetric analysis of the co-pyrolysis of paper sludge and municipal solid waste

    International Nuclear Information System (INIS)

    Fang, Shiwen; Yu, Zhaosheng; Lin, Yousheng; Hu, Shanchao; Liao, Yanfen; Ma, Xiaoqian

    2015-01-01

    Highlights: • The co-pyrolysis of municipal solid waste, paper sludge and the blends was studied. • The reactivity of paper sludge could be improved by blending municipal solid waste. • The FWO and KAS methods were used to calculate activation energy. • The average activation energy was the minimum by blending 50% paper sludge. - Abstract: The pyrolysis characteristics of municipal solid waste (MSW), paper sludge (PS) and their blends were studied through a thermogravimetric simultaneous thermal analyzer from room temperature to 1000 °C. Meanwhile their kinetics were studied by Flynn–Wall–Ozawa (FWO) and Kissinger–Akahira–Sunose (KAS) methods. The mass proportions of PS in the blends were 10%, 30%, 50%, 70%, 90%, respectively and the experiments were carried out at different heating rates (30, 40 and 50 °C/min). The initial temperature of MSW was lower than that of PS and the terminated temperature was higher than PS. The comprehensive characteristic index decreased progressively along with the decrease of the MSW proportion. The values of average activation energies calculated by FWO and KAS methods were highly consistent. The average activation energy reached the minimum number, 96.7 kJ/mol by KAS and 11.56 kJ/mol by FWO, with the proportion of PS was 50%

  11. Thermogravimetric analysis and kinetic study of bamboo waste treated by Echinodontium taxodii using a modified three-parallel-reactions model.

    Science.gov (United States)

    Yu, Hongbo; Liu, Fang; Ke, Ming; Zhang, Xiaoyu

    2015-06-01

    In this study, the effect of pretreatment with Echinodontium taxodii on thermal decomposition characteristics and kinetics of bamboo wastes was investigated by thermogravimetric analysis. The results showed fungal pretreatment can enhance the thermal degradation of bamboo. The negative effect of extractives in bamboo on the thermal decomposition can be decreased by the pretreatment. A modified three-parallel-reactions model based on isolated lignin was firstly proposed to study pyrolysis kinetics of bamboo lignocellulose. Kinetic analysis showed that with increasing pretreatment time fungal delignification was enhanced to transform the lignin component with high activation energy into that with low activation energy and raise the cellulose content in bamboo, making the thermal decomposition easier. These results demonstrated fungal pretreatment provided a potential way to improve thermal conversion efficiency of bamboo. Copyright © 2015 Elsevier Ltd. All rights reserved.

  12. Temperature-dependent deliquescence relative humidities and water activities using humidity controlled thermogravimetric analysis with application to malonic acid.

    Science.gov (United States)

    Beyer, Keith D; Schroeder, Jason R; Kissinger, Jared A

    2014-04-03

    We utilize a new experimental technique, humidity-controlled thermogravimetric analysis (HTGA), to determine temperature-dependent deliquescence relative humidities (DRH) and to determine the equilibrium concentration of a solution at a given temperature and relative humidity. To that end, we have investigated the malonic acid/water system determining the DRH and concentration/RH relationship in the temperature range 303-278 K. Excellent agreement is found with literature values for the DRH of malonic acid as a function of temperature and for the concentration/RH relationship at several temperatures. Thus, we extend the DRH and concentration/RH relationship to a broader temperature range and are using the HTGA experiments to investigate other organic acids.

  13. Combustion kinetics of hydrochar produced from hydrothermal carbonisation of Karanj (Pongamia pinnata) fruit hulls via thermogravimetric analysis.

    Science.gov (United States)

    Islam, Md Azharul; Kabir, G; Asif, M; Hameed, B H

    2015-10-01

    This study examined the combustion profile and kinetics of hydrochar produced from hydrothermal carbonisation (HTC) of Karanj fruit hulls (KFH). The HTC-KFH hydrochar combustion kinetics was investigated at 5, 10, and 20°C/min by thermogravimetric analysis. The kinetics model, Kissinger-Akahira-Sunose revealed the combustion kinetics parameters for the extent of conversion from 0.1 to 0.8; the activation energy varies from 114 to 67 kJ/mol respectively. The hydrochar combustion followed multi-steps kinetics; the Coats-Redfern models predicted the activation energies and pre-exponential constants for the hydrochar combustion zones. The diffusion models are the effective mechanism in the second and third zone. Copyright © 2015 Elsevier Ltd. All rights reserved.

  14. Thermogravimetric analysis of atomized ferromagnetic composites with multiwalled carbon nanotubes: an unusual behavior of nickel in nanospace.

    Science.gov (United States)

    Chen, Xu; Gupta, S; Santhanam, K S V

    2014-03-01

    A spin polarization of atomized ferromagnetic atoms like cobalt or nickel in nano space results in the modification of the electron configuration in the ferromagnetic atom that changes its oxidative property. We have prepared cobalt and nickel composites with multiwalled carbon nanotubes using atomized cobalt and nickel particles, for investigating their thermal oxidative behavior by thermogravimetric analysis (TGA). The composites showed the absence of a thermal oxidation in the temperature range of ambient to the break down temperature of multiwalled carbon nanotubes at 800 degrees C. At this temperature while Co composite forms cobalt oxide, the Ni composite becomes volatile that results in the divergent behavior of the two ferromagnetic compounds with a weight gain observed in TGA for Co and a loss for Ni. The mechanisms operating in the two cases are discussed in this work.

  15. Effects of additives on the co-pyrolysis of municipal solid waste and paper sludge by using thermogravimetric analysis.

    Science.gov (United States)

    Fang, Shiwen; Yu, Zhaosheng; Lin, Yan; Lin, Yousheng; Fan, Yunlong; Liao, Yanfen; Ma, Xiaoqian

    2016-06-01

    By using thermogravimetric analysis (TGA), the effects of different additives (MgO, Al2O3 and ZnO) on the pyrolysis characteristics and activation energy of municipal solid waste (MSW), paper sludge (PS) and their blends in N2 atmosphere had been investigated in this study. The experiments resulted that these additives were effective in reducing the initial temperature and activation energy. However, not all the additives were beneficial to reduce the residue mass and enhance the index D. For the different ratios of MSW and PS, the same additive even had the different influences. The catalytic effects of additives were not obvious and the pyrolysis became difficult with the increase of the proportion of PS. Based on all the contrast of the pyrolysis characteristics, MgO was the best additive and 70M30P was the best ratio, respectively. Copyright © 2016 Elsevier Ltd. All rights reserved.

  16. New sample carrier systems for thermogravimetric analysis under forced flow conditions and their influence on microkinetic results.

    Science.gov (United States)

    Seibel, C; Fieback, T M

    2015-09-01

    For thermogravimetric analysis, it has been shown that, depending on the type of sample container, different kinetic results could be obtained despite regarding the same reaction under constant conditions. This is due to limiting macrokinetic effects which are strongly dependant on the type of sample carrying system. This prompted the need for sample containers which deliver results minimally limited by diffusive mass transport. In this way, two container systems were developed, both characterized by a forced flow stream through a solid, porous bed: one from bottom to top (counter-current flow) and one from top to bottom (co-current flow). Optical test measurements were performed, the results indicating that reaction proceedings are almost fully independent of the geometrical shape of the sample containers. The Boudouard reaction was investigated with a standard crucible and the new developed systems; the reaction rates determined differed significantly, up to a factor of 6.2 at 1373 K.

  17. Determination of kinetic parameters in the pyrolysis operation and thermal behavior of Prosopis juliflora using thermogravimetric analysis.

    Science.gov (United States)

    Chandrasekaran, Arunkumar; Ramachandran, Sethumadhavan; Subbiah, Senthilmurugan

    2017-06-01

    This paper deals with the pyrolysis of Prosopis juliflora fuelwood using thermogravimetric analysis to determine the kinetic parameters at six different heating rates of 2, 5, 10, 15, 20 and 25°C/min. The activation energy of pyrolysis was calculated using different methods, namely Kissinger, Kissinger-Akahira-Sunose, Ozawa-Flynn-Wall and Friedman model and corresponding calculated activation energy were found to be 164.6, 204, 203.2, and 219.3kJ/mol, respectively for each method. The three-pseudo component model was applied to calculate the following three kinetic parameters: activation energy, pre-exponential factor and order of reaction. The experimental results were validated with model prediction for all the six heating rates. The three-pseudo component model is able to predict experimental results much accurately while considering variable order reaction model (n≠1). Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Determination of the surface density of polyethylene glycol on gold nanoparticles by use of microscale thermogravimetric analysis.

    Science.gov (United States)

    Sebby, K B; Mansfield, E

    2015-04-01

    The widespread integration of nanoparticle technologies into biomedicine will depend on the ability to repeatedly create particles with well-defined properties and predictable behaviors. For this to happen, fast, reliable, inexpensive, and widely available techniques to characterize nanomaterials are needed. Characterization of the surface molecules is particularly important since the surface, including the surface molecule density, plays a dominant role in determining how nanoparticles interact with their surroundings. Here, 10 and 30 nm gold nanoparticle NIST Standard Reference Materials were functionalized with fluorescently labeled polyethylene glycol (PEG) with either thiolate or lipoic acid anchoring groups to evaluate analytical techniques for determining surface coverage. The coating of the nanoparticles was confirmed with dynamic light scattering, microscale thermogravimetric analysis (μ-TGA), and ultraviolet-visible (UV-vis) spectroscopy. A UV-vis method for determining gold nanoparticle concentrations that takes into account spectral broadening upon functionalization was developed. The amount of bound PEG was quantified with μ-TGA, a technique analogous to thermogravimetric analysis that uses quartz crystal microbalances, and fluorescence spectroscopy of displaced ligands. It is shown that μ-TGA is a convenient technique for the quantification of ligands bound to inorganic particles while sacrificing a minimal amount of sample, and the treatment of the functionalized nanoparticle dispersions with dithiothreitol may be insufficient to achieve complete displacement of the surface ligands for quantification by fluorescence measurements. The μ-TGA and fluorescence results were used to determine ligand footprint sizes-average areas occupied by each ligand on the particles' surface. The lipoic acid bound ligands had footprint sizes of 0.21 and 0.25 nm(2) on 10 and 30 nm particles, respectively while the thiolate ligands had footprint sizes of 0.085 and 0

  19. Temperature dependence of the resonance frequency of thermogravimetric devices

    NARCIS (Netherlands)

    Iervolino, E.; Riccio, M.; Van Herwaarden, A.W.; Irace, A.; Breglio, G.; Van der Vlist, W.; Sarro, P.M.

    2010-01-01

    This paper investigates the temperature dependence of the resonance frequency of thermogravimetric (TG) devices for tip heating over the temperature range of View the MathML source 25–600?C. The resonance frequency of a fabricated TG device shows to be temperature independent for tip heating up to

  20. A comprehensive physicochemical, thermal, and spectroscopic characterization of zinc (II) chloride using X-ray diffraction, particle size distribution, differential scanning calorimetry, thermogravimetric analysis/differential thermogravimetric analysis, ultraviolet-visible, and Fourier transform-infrared spectroscopy.

    Science.gov (United States)

    Trivedi, Mahendra Kumar; Sethi, Kalyan Kumar; Panda, Parthasarathi; Jana, Snehasis

    2017-01-01

    Zinc chloride is an important inorganic compound used as a source of zinc and has other numerous industrial applications. Unfortunately, it lacks reliable and accurate physicochemical, thermal, and spectral characterization information altogether. Hence, the authors tried to explore in-depth characterization of zinc chloride using the modern analytical technique. The analysis of zinc chloride was performed using powder X-ray diffraction (PXRD), particle size distribution, differential scanning calorimetry (DSC), thermogravimetric analysis/differential thermogravimetric analysis (TGA/DTG), ultraviolet-visible spectroscopy (UV-vis), and Fourier transform-infrared (FT-IR) analytical techniques. The PXRD patterns showed well-defined, narrow, sharp, and the significant peaks. The crystallite size was found in the range of 14.70-55.40 nm and showed average crystallite size of 41.34 nm. The average particle size was found to be of 1.123 ( d 10 ), 3.025 ( d 50 ), and 6.712 ( d 90 ) μm and average surface area of 2.71 m 2 /g. The span and relative span values were 5.849 μm and 1.93, respectively. The DSC thermogram showed a small endothermic inflation at 308.10°C with the latent heat (ΔH) of fusion 28.52 J/g. An exothermic reaction was observed at 449.32°C with the ΔH of decomposition 66.10 J/g. The TGA revealed two steps of the thermal degradation and lost 8.207 and 89.72% of weight in the first and second step of degradation, respectively. Similarly, the DTG analysis disclosed T max at 508.21°C. The UV-vis spectrum showed absorbance maxima at 197.60 nm (λ max ), and FT-IR spectrum showed a peak at 511/cm might be due to the Zn-Cl stretching. These in-depth, comprehensive data would be very much useful in all stages of nutraceuticals/pharmaceuticals formulation research and development and other industrial applications.

  1. A comprehensive evaluation of water uptake on atmospherically relevant mineral surfaces: DRIFT spectroscopy, thermogravimetric analysis and aerosol growth measurements

    Directory of Open Access Journals (Sweden)

    R. J. Gustafsson

    2005-01-01

    Full Text Available The hygroscopicity of mineral aerosol samples has been examined by three independent methods: diffuse reflectance infrared Fourier transform spectroscopy, thermogravimetric analysis and differential mobility analysis. All three methods allow an evaluation of the water coverage of two samples, CaCO3 and Arizona Test dust, as a function of relative humidity. For the first time, a correlation between absolute gravimetric measurements and the other two (indirect methods has been established. Water uptake isotherms were reliably determined for both solids which at 298 K and 80% relative humidity exhibited similar coverages of ~4 monolayers. However, the behaviour at low relative humidity was markedly different in the two cases, with Arizona Test Dust showing a substantially higher affinity for water in the contact layer. This is understandable in terms of the chemical composition of these two materials. The mobility analysis results are in good accord with field observations and with our own spectroscopic and gravimetric measurements. These findings are of value for an understanding of atmospheric chemical processes.

  2. Effect of anaerobic digestion on sequential pyrolysis kinetics of organic solid wastes using thermogravimetric analysis and distributed activation energy model.

    Science.gov (United States)

    Li, Xiaowei; Mei, Qingqing; Dai, Xiaohu; Ding, Guoji

    2017-03-01

    Thermogravimetric analysis, Gaussian-fit-peak model (GFPM), and distributed activation energy model (DAEM) were firstly used to explore the effect of anaerobic digestion on sequential pyrolysis kinetic of four organic solid wastes (OSW). Results showed that the OSW weight loss mainly occurred in the second pyrolysis stage relating to organic matter decomposition. Compared with raw substrate, the weight loss of corresponding digestate was lower in the range of 180-550°C, but was higher in 550-900°C. GFPM analysis revealed that organic components volatized at peak temperatures of 188-263, 373-401 and 420-462°C had a faster degradation rate than those at 274-327°C during anaerobic digestion. DAEM analysis showed that anaerobic digestion had discrepant effects on activation energy for four OSW pyrolysis, possibly because of their different organic composition. It requires further investigation for the special organic matter, i.e., protein-like and carbohydrate-like groups, to confirm the assumption. Copyright © 2016 Elsevier Ltd. All rights reserved.

  3. Thermogravimetric analysis of the behavior of sub-bituminous coal and cellulosic ethanol residue during co-combustion.

    Science.gov (United States)

    Buratti, C; Barbanera, M; Bartocci, P; Fantozzi, F

    2015-06-01

    The influence of the addition of cellulosic ethanol residue (CER) on the combustion of Indonesian sub-bituminous coal was analyzed by non isothermal thermo-gravimetric analysis (TGA). The effect of blends ratio (5%, 10%, 15% and 20%), interaction mechanism, and heating rate (5°C/min, 10°C/min, 15°C/min, 20°C/min) on the combustion process was studied. The results show that the increase of the blending ratio allows to achieve the increase of the combustibility index from 7.49E-08 to 5.26E-07 at the blending ratio of 20%. Two types of non-isothermal kinetic analysis methods (Ozawa-Flynn-Wall and Vyazovkin) were also applied. Results indicate that the activation energy of the blends decreases with increasing the conversion rate. In particular, the blending ratio of 20% confirms to have the better combustion performance, with the average value of the activation energy equal to 41.10 kJ/mol obtained by Ozawa-Flynn-Wall model and 31.17 kJ/mol obtained by Vyazovkin model. Copyright © 2015 Elsevier Ltd. All rights reserved.

  4. Thermal decomposition and kinetics of coal and fermented cornstalk using thermogravimetric analysis.

    Science.gov (United States)

    He, Yuyuan; Chang, Chun; Li, Pan; Han, Xiuli; Li, Hongliang; Fang, Shuqi; Chen, Junying; Ma, Xiaojian

    2018-07-01

    The thermal behavior and kinetics of Yiluo coal (YC) and the residues of fermented cornstalk (FC) were investigated in this study. The Kissinger-Akahira-Sunose (KAS) and Flynn-Wall-Ozawa (FWO) methods were used for the kinetic analysis of the pyrolysis process. The results showed that the activation energy (E α ) was increased with the increase of the thermal conversion rate (α), and the average values of E α of YC, FC and the blend (m YC /m FC  = 6/4) were 304.26, 224.94 and 233.46 kJ/mol, respectively. The order reaction model function for the blend was also developed by the master-plots method. By comparing the E a and the enthalpy, it was found that the blend was favored to format activated complex due to the lower potential energy barrier. Meanwhile, the average value of Gibbs free energy of the blend was 169.83 kJ/mol, and the changes of entropies indicated that the pyrolysis process was evolved from ordered-state to disordered-state. Copyright © 2018 Elsevier Ltd. All rights reserved.

  5. Pyrolysis kinetics and thermodynamic parameters of castor (Ricinus communis) residue using thermogravimetric analysis.

    Science.gov (United States)

    Kaur, Ravneet; Gera, Poonam; Jha, Mithilesh Kumar; Bhaskar, Thallada

    2018-02-01

    Castor plant is a fast-growing, perennial shrub from Euphorbiaceae family. More than 50% of the residue is generated from its stems and leaves. The main aim of this work is to study the pyrolytic characteristics, kinetics and thermodynamic properties of castor residue. The TGA experiments were carried out from room temperature to 900 °C under an inert atmosphere at different heating rates of 5, 10, 15, 20, 30 and 40 °C/min. The kinetic analysis was carried using different models namely Kissinger, Flynn-Wall-Ozawa (FWO) and Kissinger-Akahira-Sunose (KAS). The average E ɑ calculated by FWO and KAS methods were 167.10 and 165.86 kJ/mole respectively. Gibbs free energy varied from 150.62-154.33 to 150.59-154.65 kJ/mol for FWO and KAS respectively. The HHV of castor residue was 14.43 MJ/kg, considered as potential feedstock for bio-energy production. Kinetic and thermodynamic results will be useful input for the design of pyrolytic process using castor residue as feedstock. Copyright © 2017 Elsevier Ltd. All rights reserved.

  6. Biological CO2 fixation using Chlorella vulgaris and its thermal characteristics through thermogravimetric analysis.

    Science.gov (United States)

    Razzak, Shaikh A; Ali, Saad Aldin M; Hossain, Mohammad M; Mouanda, Alexis Nzila

    2016-11-01

    The present research is focused on cultivation of microalgae strain Chlorella vulgaris for bio-fixation of CO2 coupled with biomass production. In this regard, a single semi-batch vertical tubular photobioreactor and four similar photobioreactors in series have been employed. The concentration of CO2 in the feed stream was varied from 2 to 12 % (v/v) by adjusting CO2 to air ratio. The amount of CO2 capture and algae growth were monitored by measuring decrease of CO2 concentration in the gas phase, microalgal cell density, and algal biomass production rate. The results show that 4 % CO2 gives maximum amount of biomass (0.9 g L(-1)) and productivity (0.118 g L(-1) day(-1)) of C. vulgaris in a single reactor. In series reactors, average productivity per reactor found to be 0.078 g L(-1) day(-1). The maximum CO2 uptake for single reactor also found with 4 % CO2, and it is around 0.2 g L(-1) day(-1). In series reactors, average CO2 uptake is 0.13 g L(-1) day(-1) per reactor. TOC analysis shows that the carbon content of the produced biomass is around 40.67 % of total weight. The thermochemical characteristics of the cultivated C. vulgaris samples were analyzed in the presence of air. All samples burn above 200 °C and the combustion rate become faster at around 600 °C. Almost 98 wt% of the produced biomass is combustible in this range.

  7. Study of Surface Wettability Change of Unconsolidated Sand Using Diffuse Reflectance Infrared Fourier Transform Spectroscopy and Thermogravimetric Analysis.

    Science.gov (United States)

    Gómora-Herrera, Diana; Navarrete Bolaños, Juan; Lijanova, Irina V; Olivares-Xometl, Octavio; Likhanova, Natalya V

    2018-04-01

    The effects exerted by the adsorption of vapors of a non-polar compound (deuterated benzene) and a polar compound (water) on the surface of Ottawa sand and a sample of reservoir sand (Channel), which was previously impregnated with silicon oil or two kinds of surfactants, (2-hydroxyethyl) trimethylammonium oleate (HETAO) and (2-hydroxyethyl)trimethylammonium azelate (HETAA), were studied by diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) and thermogravimetric analysis (TGA). The surface chemistry of the sandstone rocks was elucidated by X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDX). Terminal surface groups such as hydroxyls can strongly adsorb molecules that interact with these surface groups (surfactants), resulting in a wettability change. The wettability change effect suffered by the surface after treating it with surfactants was possible to be detected by the DRIFTS technique, wherein it was observed that the surface became more hydrophobic after being treated with silicon oil and HETAO; the surface became more hydrophilic after treating it with HETAA.

  8. Investigation on the co-combustion of low calorific oil shale and its semi-coke by using thermogravimetric analysis

    International Nuclear Information System (INIS)

    Yang, Yu; Lu, Xiaofeng; Wang, Quanhai

    2017-01-01

    Highlights: • The co-combustion characteristic parameters were studied. • The co-combustion of oil shale and semi-coke could be expressed roughly by the addition of individual components. • Activation energy was calculated by Coats-Redfern, distributed activation energy model and Flynn-Wall-Ozawa methods. - Abstract: In the present work, thermogravimetric analysis was employed to investigate co-combustion behaviors of Fushun low calorific oil shale and its semi-coke. The synergy effect was estimated by using the interaction coefficient and the relative error of mean square root. In addition, activation energy was also calculated by means of Coats-Redfern, distributed activation energy model and Flynn-Wall-Ozawa methods. Results indicated that with the increase of oil shale mass fraction and oxygen concentration, combustion characteristics of the samples were improved. And some little interaction did occur during the co-combustion process, but it was relatively slight. Consequently, the co-combustion of oil shale and semi-coke still could be expressed roughly by the addition of individual components of the mixtures. Furthermore, activation energy of the samples decreased slowly at the initial stage attributed to the minerals’ catalytic effects, and in the final stage, it jumped to a high value, suggesting that the burnout of the samples was difficult. Besides, the mix proportion of oil shale which was added to stabilize the combustion in the circulating fluidized bed was also theoretically calculated.

  9. Biomass pyrolysis and combustion integral and differential reaction heats with temperatures using thermogravimetric analysis/differential scanning calorimetry.

    Science.gov (United States)

    Shen, Jiacheng; Igathinathane, C; Yu, Manlu; Pothula, Anand Kumar

    2015-06-01

    Integral reaction heats of switchgrass, big bluestem, and corn stalks were determined using thermogravimetric analysis/differential scanning calorimetry (TGA/DSC). Iso-conversion differential reaction heats using TGA/DSC pyrolysis and combustion of biomass were not available, despite reports available on heats required and released. A concept of iso-conversion differential reaction heats was used to determine the differential reaction heats of each thermal characteristics segment of these materials. Results showed that the integral reaction heats were endothermic from 30 to 700°C for pyrolysis of switchgrass and big bluestem, but they were exothermic for corn stalks prior to 587°C. However, the integral reaction heats for combustion of the materials followed an endothermic to exothermic transition. The differential reaction heats of switchgrass pyrolysis were predominantly endothermic in the fraction of mass loss (0.0536-0.975), and were exothermic for corn stalks (0.0885-0.850) and big bluestem (0.736-0.919). Study results provided better insight into biomass thermal mechanism. Published by Elsevier Ltd.

  10. Pyrolysis characteristics and kinetics of microalgae via thermogravimetric analysis (TGA): A state-of-the-art review.

    Science.gov (United States)

    Bach, Quang-Vu; Chen, Wei-Hsin

    2017-12-01

    Pyrolysis is a promising route for biofuels production from microalgae at moderate temperatures (400-600°C) in an inert atmosphere. Depending on the operating conditions, pyrolysis can produce biochar and/or bio-oil. In practice, knowledge for thermal decomposition characteristics and kinetics of microalgae during pyrolysis is essential for pyrolyzer design and pyrolysis optimization. Recently, the pyrolysis kinetics of microalgae has become a crucial topic and received increasing interest from researchers. Thermogravimetric analysis (TGA) has been employed as a proven technique for studying microalgae pyrolysis in a kinetic control regime. In addition, a number of kinetic models have been applied to process the TGA data for kinetic evaluation and parameters estimation. This paper aims to provide a state-of-the art review on recent research activities in pyrolysis characteristics and kinetics of various microalgae. Common kinetic models predicting the thermal degradation of microalgae are examined and their pros and cons are illustrated. Copyright © 2017 Elsevier Ltd. All rights reserved.

  11. Thermogravimetric Analysis of Textile Dyeing Sludge (TDS) in N₂/CO₂/O₂ Atmospheres and its Combustion Model with Coal.

    Science.gov (United States)

    Zhuo, Zhongxu; Liu, Jingyong; Sun, Shuiyu; Kuo, Jiahong; Sun, Jian; Chang, Ken-Lin; Fu, Jiewen

    2018-01-01

      The combustion characteristics of textile dyeing sludge (TDS) in N2/O2, CO2/O2, and N2/CO2 atmospheres, and blends of TDS with coal were analyzed using TGA (thermogravimetric analysis). Results showed that the replacement of N2 by CO2 resulted in negative effects on the combustion and pyrolysis of TDS. Comparing N2/O2 and CO2/O2 atmospheres, combustion of TDS was easier in a N2/O2 atmosphere, but the residual mass after TDS pyrolysis in pure CO2 was less than that in N2 by approximately 4.51%. When the proportion of TDS was 30-50% in the blends of coal with TDS, a synergistic interaction clearly occurred, and it significantly promoted combustion. In considering different combustion parameters, the optimal proportion of TDS may be between 20-30%. The activation energy Ea value decreased from 155.6 kJ/mol to 53.35 kJ/mol with an increasing TDS proportion from 0% to 50%, and it rapidly decreased when the TDS proportion was below 20%.

  12. Consequences of poly(vinyl chloride) presence on the thermochemical process of lignocellulosic biomass in CO₂ by thermogravimetric analysis.

    Science.gov (United States)

    He, Yao; Ma, Xiaoqian; Zeng, Guangbo

    2015-02-01

    The thermochemical processes of lignocellulosic biomass and its mixtures with poly(vinyl chloride) (PVC) fractions were investigated by thermogravimetric analysis in CO2 atmosphere. Superposition property was assumed to examine whether and/or to what extent interactions occurred during the mixture decomposition. Results showed that interactions existed, of which the intensities changed with reaction stage, heating rate and PVC quantity, and they actively behaved toward the decomposition in most cases. With PVC presence, lignocellulosic biomass turned from three-stage to four-stage decomposition process where the reactions occurred at lower temperatures with heightened intensity, especially in the first stage. The measured activation energies calculated by Ozawa-Flynn-Wall and Vyazovkin methods were of minor difference <5 kJ/mol, and comparing them between materials in each stage confirmed the results of interaction impact. This work provides a theoretical basis bringing about the possibilities of recycling CO2 into a reaction medium of thermo-treatment of lignocellulosic material with PVC contaminants. Copyright © 2014 Elsevier Ltd. All rights reserved.

  13. Measurement of the oxidation of spent fuel between 140/degree/ and 225/degree/C by thermogravimetric analysis

    International Nuclear Information System (INIS)

    Woodley, R.E.; Einziger, R.E.; Buchanan, H.C.

    1988-09-01

    A series of PWR spent fuel samples from Turkey Point Unit 3 have been oxidized at temperatures between 140/degree/ and 225/degree/C in air atmospheres with dew points between 14.5/degree/ and /minus/70/degree/C, using a thermogravimetric analysis system (TGA). Tests lasted between 400 and 2100 hours. At the conclusion of a test, the atmosphere was sampled to determine the release of fission gas during testing, and the fuel samples were analyzed for microstructural changes. It appears that the mechanism for oxidation of spent fuel to U/sub 3/O/sub 7/ takes place in two steps that occur somewhat simultaneously. Oxygen migrates along the grain boundaries, which are oxidized and enlarged. The grains oxidize by the inward progression of a layer of U/sub 4/O/sub 9/ saturated with oxygen. A simplified model of the mechanism, which considers oxygen diffusion through the product layer as the rate-controlling step, yields an activation energy of 27 /plus minus/ 4 kcal/mol. Moisture, between dew points of /minus/70/degree/ to +14.5/degree/C, i.e., water vapor partial pressures varying over four orders of magnitude, had no significant effect on the oxidation rate. 34 refs., 12 figs., 6 tabs

  14. Investigation on the co-combustion of oil shale and municipal solid waste by using thermogravimetric analysis

    International Nuclear Information System (INIS)

    Fan, Yunlong; Yu, Zhaosheng; Fang, Shiwen; Lin, Yan; Lin, Yousheng; Liao, Yanfen; Ma, Xiaoqian

    2016-01-01

    Highlights: • Co-combustion of oil shale with municipal solid waste created significant changes. • Blending with municipal solid wastes could improve the combustion performance. • 10–30% of oil shale in the blends could be determined as the optimum ratio range. • Activation energy were calculated by the conversion rate and different proportion. - Abstract: The aim of this study is trying to reveal the thermal characteristics and kinetics of oil shale, municipal solid waste and their blends in the combustion process which are needed for efficient utilization. The combustion experiment is carried out in a thermogravimetric simultaneous thermal analyzer, where the temperature ranged from 110 °C to 900 °C at three different heating rates as 10 °C/min, 20 °C/min and 30 °C/min. Their kinetics were studied by Ozawa–Flynn–Wall and Friedmen methods. According to the data analysis, combustion characteristic index increased progressively with the increase of the proportion of municipal solid waste. And it’s suggested that there was certain interaction in the combustion process of oil shale and municipal solid waste. The average activation energy of the blends reached the minimum value, 177.7927 kJ/mol by Ozawa–Flynn–Wall method and 167.4234 kJ/mol by Friedmen method, when the proportion of MSW was 70%.

  15. Thermogravimetric Analysis of Modified Hematite by Methane (CH{sub 4}) for Chemical-Looping Combustion: A Global Kinetics Mechanism

    Energy Technology Data Exchange (ETDEWEB)

    Monazam, Esmail R; Breault, Ronald W; Siriwardane, Ranjani; Miller, Duane D

    2013-10-01

    Iron oxide (Fe{sub 2}O{sub 3}) or in its natural form (hematite) is a potential material to capture CO{sub 2} through the chemical-looping combustion (CLC) process. It is known that magnesium (Mg) is an effective methyl cleaving catalyst and as such it has been combined with hematite to assess any possible enhancement to the kinetic rate for the reduction of Fe{sub 2}O{sub 3} with methane. Therefore, in order to evaluate its effectiveness as a hematite additive, the behaviors of Mg-modified hematite samples (hematite –5% Mg(OH){sub 2}) have been analyzed with regard to assessing any enhancement to the kinetic rate process. The Mg-modified hematite was prepared by hydrothermal synthesis. The reactivity experiments were conducted in a thermogravimetric analyzer (TGA) using continuous stream of CH{sub 4} (5, 10, and 20%) at temperatures ranging from 700 to 825 {degrees}C over ten reduction cycles. The mass spectroscopy analysis of product gas indicated the presence of CO{sub 2}, H{sub 2}O, H{sub 2} and CO in the gaseous product. The kinetic data at reduction step obtained by isothermal experiments could be well fitted by two parallel rate equations. The modified hematite samples showed higher reactivity as compared to unmodified hematite samples during reduction at all investigated temperatures.

  16. A meta-analysis of adiponectin gene rs22411766 T>G polymorphism and ischemic stroke susceptibility

    Directory of Open Access Journals (Sweden)

    Xiuju Chen

    2016-01-01

    Full Text Available Several studies have investigated the correlation between adiponectin gene rs22411766 T>G polymorphism and ischemic stroke risk. However, the results were not conclusive with each other. Therefore, to overcome this obstacle, we performed this meta-analysis to further explicate the adiponectin gene rs22411766 T>G polymorphism and ischemic stroke susceptibility. Case-control or cohort studies focused on adiponectin gene rs22411766 T>G polymorphism and ischemic stroke risk were electronic searched in the databases of Medline, Pubmed, Cochrane library, Excerpta Medica database(EMBASE and China National Knowledge Infrastructure (CNKI. All the potentially relevant studies were included in this meta-analysis. The association between adiponectin gene rs22411766 T>G polymorphism and ischemic stroke was expressed by odds ratio with its confidence interval. Publication bias has been assessed by begg’s funnel plot. All the analyses have been performed by Revman 5.1 statistical software. Finally, a total of six studies with 1,345 cases and 1,421 controls were included in this meta-analysis. Our results demonstrated that there was a significant association between adiponectin gene rs22411766 T>G polymorphism and ischemic stroke risk (p<0.05. People with G single nucleotide of adiponectin gene have the increased risk of developing ischemic stroke compared to T single nucleotide.

  17. Comparative study on the pyrolysis behaviour and kinetics of two macroalgae biomass (Gracilaria changii and Gelidium pusillum) by thermogravimetric analysis

    Science.gov (United States)

    Roslee, A. N.; Munajat, N. F.

    2017-10-01

    Macroalgae are often referred as seaweed and could be significant biomass resource for the production of numerous energy carriers including biofuels. In this study, the chemical composition of Gracilaria changii (G. changii) and Gelidium pusillum (G. pusillum) were determined through proximate and ultimate analysis and the thermal degradation behaviour of G. changii and G. pusillum were investigated via thermogravimetric analysis (TGA) in determining the important main composition to be considered as biomass fuels. It has found the pyrolysis of G. changii and G. pusillum consists of three stages and stage II is the main decomposition stage with major mass loss of around 52.16% and 44.42%, respectively. The TGA data were then used for determination of kinetic parameters of the pyrolysis process using three model-free methods: Kissinger, Kissinger-Akahira-Sunose (KAS) and Flynn-Wall-Ozawa (FWO). The apparent activation energy calculated by using Kissinger method for G. changii was lower than G. Pusillum, i.e.173.12 kJ/mol and 193.22 kJ/mol, respectively. The activation energies calculated from KAS and FWO methods were increased with increasing the pyrolysis conversion with average activation energies of 172.32 kJ/mol and 181.19 kJ/mol for G. changii while for G. pusillum (177.42 kJ/mol and 187.4 kJ/mol). G. pusillum has lower and wider distribution of activation energy and revealed that the pyrolysis process for G. changii was easier than G. pusillum. These data provide information for further application for designing and modelling in thermochemical conversion system of macroalgae biomass.

  18. A thermogravimetric analysis (TGA) method to determine the catalytic conversion of cellulose from carbon-supported hydrogenolysis process

    International Nuclear Information System (INIS)

    Leal, Glauco F.; Ramos, Luiz A.; Barrett, Dean H.; Curvelo, Antonio Aprígio S.; Rodella, Cristiane B.

    2015-01-01

    Graphical abstract: - Highlights: • A new method to determine the catalytic conversion of cellulose using TGA has been developed. • TGA is able to differentiate between carbon from cellulose and carbon from the catalyst. • Building an analytical curve from TGA results enables the accurate determination of cellulose conversion. - Abstract: The ability to determine the quantity of solid reactant that has been transformed after a catalytic reaction is fundamental in accurately defining the conversion of the catalyst. This quantity is also central when investigating the recyclability of a solid catalyst as well as process control in an industrial catalytic application. However, when using carbon-supported catalysts for the conversion of cellulose this value is difficult to obtain using only a gravimetric method. The difficulty lies in weighing errors caused by loss of the solid mixture (catalyst and non-converted cellulose) after the reaction and/or moisture adsorption by the substrate. These errors are then propagated into the conversion calculation giving erroneous results. Thus, a quantitative method using thermogravimetric analysis (TGA) has been developed to determine the quantity of cellulose after a catalytic reaction by using a tungsten carbide catalyst supported on activated carbon. Stepped separation of TGA curves was used for quantitative analysis where three thermal events were identified: moisture loss, cellulose decomposition and CO/CO 2 formation. An analytical curve was derived and applied to quantify the residual cellulose after catalytic reactions which were performed at various temperatures and reaction times. The catalytic conversion was calculated and compared to the standard gravimetric method. Results showed that catalytic cellulose conversion can be determined using TGA and exhibits lower uncertainty (±2%) when compared to gravimetric determination (±5%). Therefore, it is a simple and relatively inexpensive method to determine catalytic

  19. Thermogravimetric analysis, PXRD, EDX and XPS study of chrysocolla (Cu,Al)2H2Si2O5(OH)4·nH2O-structural implications

    International Nuclear Information System (INIS)

    Frost, Ray L.; Xi, Yunfei; Wood, Barry J.

    2012-01-01

    Highlights: ► We have undertaken a TG X PS study of the mineral chrysocolla. ► The chemical bonding of Cu, O and Si has been determined. ► It is concluded that chrysocolla is a mineral in its own right. ► It is not a colloidal mixture of spertiniite and amorphous silica. - Abstract: Selected chrysocolla mineral samples from different origins have been studied by using PXRD, SEM, EDX and XPS. The XRD patterns show that the chrysocolla mineral samples are non-diffracting and no other phases are present in the minerals, thus showing the chrysocolla samples are pure. SEM analyses show the chrysocolla surfaces are featureless. EDX analyses enable the formulae of the chrysocolla samples to be calculated. The thermal decomposition of the mineral chrysocolla has been studied using a combination of thermogravimetric analysis and derivative thermogravimetric analysis. Five thermal decomposition mass loss steps are observed for the chrysocolla from Arizona (a) at 125 °C with the loss of water, (b) at 340 °C with the loss of hydroxyl units, (c) at 468.5 °C with a further loss of hydroxyls, (d) at 821 °C with oxygen loss and (e) at 895 °C with a further loss of oxygen. The thermal analysis of the chrysocolla from Congo shows mass losses at 125, 275.3, 805.6 and 877.4 °C and for the Nevada chrysocolla, mass loss steps at 268, 333, 463, 786.0 and 817.7 °C are observed. The thermal analysis of spertiniite is very different from that of chrysocolla and thermally decomposes at around 160 °C. XPS shows that there are two different copper species present, one which is bonded to oxygen and one to a hydroxyl unit. The O 1s is broad and very symmetrical suggesting two O species of equal number. The bond energy of 102.9 eV for the Si 2p suggests that it is in the form of a silicate. The bond energy is much higher for silicas around ∼103.5 eV. The reported value for silica gel has Si 2p at 103.4 eV. The combination of TG, PXRD, EDX and XPS adds to our fundamental

  20. Influence of catalysts on co-combustion of sewage sludge and water hyacinth blends as determined by TG-MS analysis.

    Science.gov (United States)

    Huang, Limao; Xie, Candie; Liu, Jingyong; Zhang, Xiaochun; Chang, KenLin; Kuo, Jiahong; Sun, Jian; Xie, Wuming; Zheng, Li; Sun, Shuiyu; Buyukada, Musa; Evrendilek, Fatih

    2018-01-01

    Effects of the three metal carbonates (K 2 CO 3 , Na 2 CO 3 , and MgCO 3 ) were quantified on catalytic co-combustion of the sewage sludge and water hyacinth (SW) blend using a thermogravimetric-mass spectrometric (TG-MS) analysis and kinetics modeling. The main dominating steps of the catalysts were the organic volatile matter release and combustion stage. Weighted mean values of activation energy (E m ) were estimated at 181.18KJ·mol -1 , 199.76KJ·mol -1 , 138.76KJ·mol -1 , and 177.88KJ·mol -1 for SW, SW+5% K 2 CO 3 , SW+5% Na 2 CO 3 , and SW+5% MgCO 3 , respectively. The lowest E m occurred with SW+5% Na 2 CO 3 . Overall, catalyst effect on co-combustion appeared to be negligible as indicated by Gibbs free energy (ΔG). The normalized intensities of SW+MgCO 3 were strongest. The addition of Na 2 CO 3 and MgCO 3 to SW increased flue gases emissions (CO 2 , NO 2 , SO 2 , HCN, and NH 3 ) of SW, whereas the addition of K 2 CO 3 to SW reduced flue gases emissions from the entire combustion process. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. Development and in house validation of a new thermogravimetric method for water content analysis in soft brown sugar.

    Science.gov (United States)

    Ducat, Giseli; Felsner, Maria L; da Costa Neto, Pedro R; Quináia, Sueli P

    2015-06-15

    Recently the use of brown sugar has increased due to its nutritional characteristics, thus requiring a more rigid quality control. The development of a method for water content analysis in soft brown sugar is carried out for the first time by TG/DTA with application of different statistical tests. The results of the optimization study suggest that heating rates of 5°C min(-1) and an alumina sample holder improve the efficiency of the drying process. The validation study showed that thermo gravimetry presents good accuracy and precision for water content analysis in soft brown sugar samples. This technique offers advantages over other analytical methods as it does not use toxic and costly reagents or solvents, it does not need any sample preparation, and it allows the identification of the temperature at which water is completely eliminated in relation to other volatile degradation products. This is an important advantage over the official method (loss on drying). Copyright © 2015 Elsevier Ltd. All rights reserved.

  2. TG-MS analysis and kinetic study for thermal decomposition of six representative components of municipal solid waste under steam atmosphere.

    Science.gov (United States)

    Zhang, Jinzhi; Chen, Tianju; Wu, Jingli; Wu, Jinhu

    2015-09-01

    Thermal decomposition of six representative components of municipal solid waste (MSW, including lignin, printing paper, cotton, rubber, polyvinyl chloride (PVC) and cabbage) was investigated by thermogravimetric-mass spectroscopy (TG-MS) under steam atmosphere. Compared with TG and derivative thermogravimetric (DTG) curves under N2 atmosphere, thermal decomposition of MSW components under steam atmosphere was divided into pyrolysis and gasification stages. In the pyrolysis stage, the shapes of TG and DTG curves under steam atmosphere were almost the same with those under N2 atmosphere. In the gasification stage, the presence of steam led to a greater mass loss because of the steam partial oxidation of char residue. The evolution profiles of H2, CH4, CO and CO2 were well consistent with DTG curves in terms of appearance of peaks and relevant stages in the whole temperature range, and the steam partial oxidation of char residue promoted the generation of more gas products in high temperature range. The multi-Gaussian distributed activation energy model (DAEM) was proved plausible to describe thermal decomposition behaviours of MSW components under steam atmosphere. Copyright © 2015 Elsevier Ltd. All rights reserved.

  3. Determination of effective moisture diffusivity and drying kinetics for poplar sawdust by thermogravimetric analysis under isothermal condition.

    Science.gov (United States)

    Chen, Dengyu; Zheng, Yan; Zhu, Xifeng

    2012-03-01

    The current study presents a thermogravimetric method to determine the effective moisture diffusivity and drying kinetics of biomass. Drying experiments on poplar sawdust were performed at four temperatures (60, 70, 80, and 90°C) by a thermogravimetric analyzer (TGA). The major assumption in experimentally determining effective diffusivity by Fick's diffusion equation is that drying is mass transfer limited and temperature remains isothermal during drying. The results indicated that TGA could well achieve these determining conditions. The drying process of sawdust mostly took place in the falling rate period. Midilli-Kucuk model showed the best fit for all experimental data. The effective diffusivity values changed from 9.38 × 10(-10)m(2)/s to 1.38 × 10(-9)m(2)/s within the given temperature range, and the activation energy was calculated to be 12.3 kJ/mol. Copyright © 2011 Elsevier Ltd. All rights reserved.

  4. Combustion studies of coal derived solid fuels by thermogravimetric analysis. III. Correlation between burnout temperature and carbon combustion efficiency

    Science.gov (United States)

    Rostam-Abadi, M.; DeBarr, J.A.; Chen, W.T.

    1990-01-01

    Burning profiles of 35-53 ??m size fractions of an Illinois coal and three partially devolatilized coals prepared from the original coal were obtained using a thermogravimetric analyzer. The burning profile burnout temperatures were higher for lower volatile fuels and correlated well with carbon combustion efficiencies of the fuels when burned in a laboratory-scale laminar flow reactor. Fuels with higher burnout temperatures had lower carbon combustion efficiencies under various time-temperature conditions in the laboratory-scale reactor. ?? 1990.

  5. DDGS chars gasification with CO{sub 2}: a kinetic study using TG analysis

    Energy Technology Data Exchange (ETDEWEB)

    Meng, Xiangmei; Jong, Wiebren de; Fu, Ningjie; Verkooijen, Adrian H.M. [Delft University of Technology, Process and Energy Department, Faculty of Mechanical, Maritime and Materials Engineering, Delft (Netherlands)

    2011-12-15

    Dry Distiller's Grains with Solubles (DDGS) is a by-product during ethanol production from cereals which is currently mainly used as feedstock for cattle. With the growth of the ethanol industry, the increasing supply of DDGS may saturate the livestock feed market; thus, its potential applications need to be explored. DDGS gasification in a 100-kW{sub th} circulating fluidized bed (CFB) steam-O{sub 2} blown gasifier has been studied. However, the modeling of DDGS gasification process encounters difficulties due to the unavailable knowledge of DDGS char gasification kinetics. Therefore, in this paper, gasification kinetics of DDGS char with CO{sub 2} was investigated using thermogravimetric analysis (TGA). Two different types of char samples have been tested. Char type one (PYR-Char) was obtained after DDGS pyrolysis in a TGA at a final temperature of 750 C or 850 C for 20 min. Char type two (CFB-Char) was obtained after DDGS gasification in the 100-kW{sub th} CFB gasifier within the temperature range of 790 C to 820 C with a steam/biomass mass ratio of 0.81 and oxygen to biomass stoichiometric ratio of approximately 0.38. The influences of pyrolysis temperature (750 C, 850 C), heating rate (10 C/min, 30 C/min, 50 C/min, 70 C/min), CO{sub 2} concentration (10, 20, 30 vol.%), and gasification temperature (900 C, 1,000 C, 1,100 C) on the reaction rate of char-CO{sub 2} reaction were determined. Two representative gas-solid reaction models, the volumetric reaction model (VRM) and the shrinking core model (SCM) were applied in order to determine kinetic parameters. It was found that the calculated activation energy (E{sub a}) values using SCM were slightly lower than those using VRM. The calculated E{sub a} values for PYR-Char using both models were in the range of 100-165 kJ/mol, while the calculated E{sub a} values for CFB-Char were in the range of 55-100 kJ/mol. It was observed by scanning electron microscopy (SEM) that CFB-Char was more fragile and PYR

  6. Influence of metal additives on pyrolysis behavior of bituminous coal by TG-FTIR analysis

    Energy Technology Data Exchange (ETDEWEB)

    Su, Wenjuan; Fang, Mengxiang; Cen, Jianmeng; Li, Chao; Luo, Zhongyang; Cen, Kefa [Zhejiang Univ., Hangzhou (China). State Key Lab. of Clean Energy Utilization

    2013-07-01

    To study the catalytic effects of alkali, alkaline earth and transition metal additives on coal pyrolysis behavior, bituminous coal loaded NaCl, KCl, CaCl{sub 2}, MgCl{sub 2}, FeCl{sub 3} and NiCl{sub 2} was respectively investigated using Thermogravimetry and Fourier Transform Infrared Spectroscopy (TG-FTIR). Results indicated that the maximum mass loss rate decreased under the metal additives in the primary pyrolysis stage. The total mass loss of pyrolysis was reduced in metals catalyzed pyrolysis except for Na loaded sample. Kinetic analysis was taken for all samples adopting the method of Coats-Redfern. Activation energy of raw coal in the primary pyrolysis stage was 92.15vkJ.mol{sup -1}, which was lowered to 44.59-73.42 kJ.mol{sup -1} under metal additives. The orders of catalytic effect for this bituminous coal were Mg > Fe > Ca > Ni > K > Na according to their activation energies. Several investigated volatiles including CH{sub 4}, CO{sub 2}, CO, toluene, phenol and formic acid were identified from FTIR spectra. The yields of CH{sub 4}, CO{sub 2}, toluene, phenol and formic acid were decreased, but the evolution of CO was increased. The presence of metals in the coal samples have been involved in a repeated bond-forming and bond-breaking process, which greatly hindered the release of tars during pyrolysis as the tar precursors were connected to coal/char matrix and were thermally cracked, becoming a part of char.

  7. DETERMINATION OF SATURATION VAPOR PRESSURE OF LOW VOLATILE SUBSTANCES THROUGH THE STUDY OF EVAPORATION RATE BY THERMOGRAVIMETRIC ANALYSIS

    Directory of Open Access Journals (Sweden)

    R. V. Ralys

    2015-11-01

    Full Text Available Subject of Study.Research of vapor pressure of low volatile substances is a complicated problem due to both direct experimental implementation complexity and, most significantly, the issues faced correctness of the analysis and processing of experimental data. That is why it is usually required engaging the reference substances (with vapor pressures well studied. The latter drastically reduces the effectiveness of the experimental methods used and narrows their applicability. The paper deals with an approach to the evaporation process description (sublimation of low volatile substances based on molecular kinetic description in view of diffusive and convection processes. The proposed approach relies on experimental thermogravimetricfindingsina wide range of temperatures, flow rates ofthe purge gas and time. Method. A new approach is based on the calculation of the vapor pressure and uses the data about the speed of evaporation by thermogravimetric analysis depending on the temperature, the flow rate of the purge gas, and the evaporation time. The basis for calculation is the diffusion-kinetic description of the process of evaporation (mass loss of the substance from the exposed surface. The method is applicable to determine the thermodynamic characteristics for both the evaporation (the equilibrium liquid - vapor and sublimation (the equilibrium solid - vapor. We proposed the appropriate method of the experiment and analysis of its data in order to find the saturated vapor pressure of individual substances of low volatility. Main Results. The method has been tested on substances with insufficiently reliable and complete study of the thermodynamic characteristics but, despite this, are often used (because of the other data limitations as reference ones. The vaporization process (liquid-vapor has been studied for di-n-butyl phthalate C16H22O4 at 323,15–443,15 К, and sublimation for benzoic acid C7H6O2at 303,15–183,15 К. Both processes have

  8. Thermogravimetric studies of New Zealand coals

    Energy Technology Data Exchange (ETDEWEB)

    Beamish, B.B.; Rodgers, K.A.; Benfell, K.E.; Shaw, K.J. [University of Auckland, Auckland (New Zealand). Dept. of Geology

    1997-12-31

    The thermal behaviour of New Zealand coals may be reliably characterised by a series of tightly constrained thermogravimetric (TG) procedures of high repeatability developed in the Department of Geology at The University of Auckland. Proximate, combustion and char reactivity analyses can be routinely obtained for run-of-mine samples. Volatile matter determination by TG produces an acceptable reproducible result compared with the ISO method, whereas further refinement of the technique is necessary to achieve the same level of precision for ash content of New Zealand low rank coals. Combining combustion and char reactivity analyses enables the performance of a coal to be assessed under differing operating conditions, and offers the opportunity to elucidate competing effects of major element geochemistry of the coal. 12 refs., 4 figs., 2 tabs.

  9. Comparison of thermal behavior of natural and hot-washed sisal fibers based on their main components: Cellulose, xylan and lignin. TG-FTIR analysis of volatile products

    Energy Technology Data Exchange (ETDEWEB)

    Benítez-Guerrero, Mónica, E-mail: monica_benitez_guerrero@yahoo.es [Departamento de Ingeniería Civil, Materiales y Fabricación, Universidad de Málaga, Escuela de Ingenierías, C/ Dr. Ortiz Ramos s/n, Campus Teatinos, 29071 Málaga (Spain); López-Beceiro, Jorge [Departamento de Ingeniería Industrial II, Escola Politécnica Superior, Universidade da Coruña, Avda. Mendizábal, 15403 Ferrol (Spain); Sánchez-Jiménez, Pedro E. [Instituto de Ciencia de Materiales de Sevilla, CSIC-Universidad de Sevilla, C/ Américo Vespucio 49, 41092 Sevilla (Spain); Pascual-Cosp, José [Departamento de Ingeniería Civil, Materiales y Fabricación, Universidad de Málaga, Escuela de Ingenierías, C/ Dr. Ortiz Ramos s/n, Campus Teatinos, 29071 Málaga (Spain)

    2014-04-01

    Highlights: • Thermal decomposition of sisal fibers has been discussed. • Decompositions of lignocellulosic components and sisal are compared by TXRD and TG-FTIR. • Hot washing reduces the temperature range in which sisal decomposition occurs. • Sisal cellulose decomposition goes by an alternative route to levoglucosan generation. - Abstract: This paper presents in a comprehensive way the thermal behavior of natural and hot-washed sisal fibers, based on the fundamental components of lignocellulosic materials: cellulose, xylan and lignin. The research highlights the influence exerted on the thermal stability of sisal fibers by other constituents such as non-cellulosic polysaccharides (NCP) and mineral matter. Thermal changes were investigated by thermal X-ray diffraction (TXRD), analyzing the crystallinity index (%Ic) of cellulosic samples, and by simultaneous thermogravimetric and differential thermal analysis coupled with Fourier-transformed infrared spectrometry (TG/DTA-FTIR), which allowed to examine the evolution of the main volatile compounds evolved during the degradation under inert and oxidizing atmospheres. The work demonstrates the potential of this technique to elucidate different steps during the thermal decomposition of sisal, providing extensible results to other lignocellulosic fibers, through the analysis of the evolution of CO{sub 2}, CO, H{sub 2}O, CH{sub 4}, acetic acid, formic acid, methanol, formaldehyde and 2-butanone, and comparing it with the volatile products from pyrolysis of the biomass components. The hydroxyacetaldehyde detected during pyrolysis of sisal is indicative of an alternative route to that of levoglucosan, generated during cellulose pyrolysis. Hot-washing at 75 °C mostly extracts non-cellulosic components of low decomposition temperature, and reduces the range of temperature in which sisal decomposition occurs, causing a retard in the pyrolysis stage and increasing Tb{sub NCP} and Tb{sub CEL}, temperatures at the

  10. Electrodynamic thermogravimetric analyzer

    International Nuclear Information System (INIS)

    Spjut, R.E.; Bar-Ziv, E.; Sarofim, A.F.; Longwell, J.P.

    1986-01-01

    The design and operation of a new device for studying single-aerosol-particle kinetics at elevated temperatures, the electrodynamic thermogravimetric analyzer (EDTGA), was examined theoretically and experimentally. The completed device consists of an electrodynamic balance modified to permit particle heating by a CO 2 laser, temperature measurement by a three-color infrared-pyrometry system, and continuous weighing by a position-control system. In this paper, the position-control, particle-weight-measurement, heating, and temperature-measurement systems are described and their limitations examined

  11. Thermogravimetric analysis and TEM characterization of the oxidation and defect sites of carbon nanotubes synthesized by CVD of methane

    International Nuclear Information System (INIS)

    Li Haipeng; Zhao Naiqin; He Chunnian; Shi Chunsheng; Du Xiwen; Li Jiajun

    2008-01-01

    Changes in the thermogravimetrically determined oxidation behaviors of CVD-grown multi-walled carbon nanotubes (MWNTs) over Ni/Al catalyst with different Ni content were examined. Catalyst type was found to have a measurable impact upon nanotube stability, suggesting differing levels of crystalline perfection in the resulting nanotubes. With increasing the Ni content in the Ni/Al catalyst, the CNTs obtained became less stable during heat treatment in air. Furthermore, high-resolution transmission electron microscopy was employed to investigate the defect sites of as-grown MWNTs. The results provide evidence showing that defect sites along the walls and at the ends of the raw MWNTs facilitate the thermal oxidative destruction of the nanotubes

  12. Analysis of Mechanical and Thermogravimetric Properties of Composite Materials Based on PVA/MWCNT and Styrene-Acrylic Copolymer/MWCNT

    Science.gov (United States)

    Volynets, N. I.; Poddubskaya, O. G.; Demidenko, M. I.; Lyubimov, A. G.; Kuzhir, P. P.; Suslyaev, V. I.; Pletnev, M. A.; Zicans, Janis

    2017-08-01

    Mechanical and thermogravimetric properties of polymer composite materials with various concentrations of multiwalled carbon nanotubes effectively shielding radiation in the radio frequency (20 Hz - 1 MHz) and microwave (26-36 GHz) frequency ranges are studied. As a matrix, widely available polymeric materials, such as polyvinyl acetate and styrene-acrylate, were used in the form of dispersions. From the analysis of the obtained experimental data, it was shown that the introduction of carbon nanotubes into the polymer matrix makes it possible to increase mechanical properties and thermal stability of composite materials.

  13. Trend analysis of body weight parameters, mortality, and incidence of spontaneous tumors in Tg.rasH2 mice.

    Science.gov (United States)

    Paranjpe, Madhav G; Denton, Melissa D; Vidmar, Tom; Elbekai, Reem H

    2014-01-01

    Carcinogenicity studies have been performed in conventional 2-year rodent studies for at least 3 decades, whereas the short-term carcinogenicity studies in transgenic mice, such as Tg.rasH2, have only been performed over the last decade. In the 2-year conventional rodent studies, interlinked problems, such as increasing trends in the initial body weights, increased body weight gains, high incidence of spontaneous tumors, and low survival, that complicate the interpretation of findings have been well established. However, these end points have not been evaluated in the short-term carcinogenicity studies involving the Tg.rasH2 mice. In this article, we present retrospective analysis of data obtained from control groups in 26-week carcinogenicity studies conducted in Tg.rasH2 mice since 2004. Our analysis showed statistically significant decreasing trends in initial body weights of both sexes. Although the terminal body weights did not show any significant trends, there was a statistically significant increasing trend toward body weight gains, more so in males than in females, which correlated with increasing trends in the food consumption. There were no statistically significant alterations in mortality trends. In addition, the incidence of all common spontaneous tumors remained fairly constant with no statistically significant differences in trends. © The Author(s) 2014.

  14. Evaluation of co-pyrolysis petrochemical wastewater sludge with lignite in a thermogravimetric analyzer and a packed-bed reactor: Pyrolysis characteristics, kinetics, and products analysis.

    Science.gov (United States)

    Mu, Lin; Chen, Jianbiao; Yao, Pikai; Zhou, Dapeng; Zhao, Liang; Yin, Hongchao

    2016-12-01

    Co-pyrolysis characteristics of petrochemical wastewater sludge and Huolinhe lignite were investigated using thermogravimetric analyzer and packed-bed reactor coupled with Fourier transform infrared spectrometer and gas chromatography. The pyrolysis characteristics of the blends at various sludge blending ratios were compared with those of the individual materials. Thermogravimetric experiments showed that the interactions between the blends were beneficial to generate more residues. In packed-bed reactor, synergetic effects promoted the release of gas products and left less liquid and solid products than those calculated by additive manner. Fourier transform infrared spectrometer analysis showed that main functional groups in chars gradually disappeared with pyrolysis temperatures increasing, and H 2 O, CH 4 , CO, and CO 2 appeared in volatiles during pyrolysis. Gas compositions analysis indicated that, the yields of H 2 and CO clearly increased as the pyrolysis temperature and sludge blending ratio increasing, while the changes of CH 4 and CO 2 yields were relatively complex. Copyright © 2016 Elsevier Ltd. All rights reserved.

  15. SU-F-T-248: FMEA Risk Analysis Implementation (AAPM TG-100) in Total Skin Electron Irradiation Technique

    Energy Technology Data Exchange (ETDEWEB)

    Ibanez-Rosello, B; Bautista-Ballesteros, J; Bonaque, J [Hospital La Fe, Valencia, Valencia (Spain); Perez-Calatayud, J [Hospital La Fe, Valencia, Valencia (Spain); Clinica Benidorm, Benidorm, Alicante (Spain); Gonzalez-Sanchis, A; Lopez-Torrecilla, J; Brualla-Gonzalez, L; Garcia-Hernandez, T; Vicedo-Gonzalez, A; Granero, D; Serrano, A; Borderia, B; Solera, C [Hospital General ERESA, Valencia, Valencia (Spain); Rosello, J [Hospital General ERESA, Valencia, Valencia (Spain); Universidad de Valencia, Valencia, Valencia (Spain)

    2016-06-15

    Purpose: Total Skin Electron Irradiation (TSEI) is a radiotherapy treatment which involves irradiating the entire body surface as homogeneously as possible. It is composed of an extensive multi-step technique in which quality management requires high consumption of resources and a fluid communication between the involved staff, necessary to improve the safety of treatment. The TG-100 proposes a new perspective of quality management in radiotherapy, presenting a systematic method of risk analysis throughout the global flow of the stages through the patient. The purpose of this work has been to apply TG-100 approach to the TSEI procedure in our institution. Methods: A multidisciplinary team specifically targeting TSEI procedure was formed, that met regularly and jointly developed the process map (PM), following TG-100 guidelines of the AAPM. This PM is a visual representation of the temporal flow of steps through the patient since start until the end of his stay in the radiotherapy service. Results: This is the first stage of the full risk analysis, which is being carried out in the center. The PM provides an overview of the process and facilitates the understanding of the team members who will participate in the subsequent analysis. Currently, the team is implementing the analysis of failure modes and effects (FMEA). The failure modes of each of the steps have been identified and assessors are assigning a value of severity (S), frequency of occurrence (O) and lack of detection (D) individually. To our knowledge, this is the first PM made for the TSEI. The developed PM can be useful for those centers that intend to implement the TSEI technique. Conclusion: The PM of TSEI technique has been established, as the first stage of full risk analysis, performed in a reference center in this treatment.

  16. Investigation of the effects of phase transformations in micro and nano aluminum powders on kinetics of oxidation using thermogravimetric analysis.

    Science.gov (United States)

    Saceleanu, Florin; Atashin, Sanam; Wen, John Z

    2017-07-26

    Aluminum micro and nanoparticles are key ingredients in the synthesis of nano energetic materials. Hence it is important to characterize the kinetics and the rate controlling process of their oxidation. The literature shows that the mass diffusion and phase transformation within the aluminum oxide shell are important. However, the description of physical processes regarding simultaneous oxidation and phase transformation is lacking. In this paper, the controlled thermogravimetric (TGA) oxidation of 40-60 nm and 1 µm Al powders is investigated at constant heating rates and under isothermal conditions, respectively, upon varying the partial pressure of oxygen. It is found that the core-shell model of homogenous oxidation is applicable to explain the TGA results when the shell does not undergo phase transformation, which predicts the apparent activation energy in good agreement with the literature data. On the other hand, the simultaneous oxidation and phase transformation is able to be addressed using the JMAK model which reveals key parameters of the rate controlling processes. Mass diffusion is indeed rate determining during the oxidation of Al micro and nanopowders while the kinetics of the reaction is fast. Unlike the micron powders, the particle size distribution has a significant effect on the shape of the oxidation curves of the nanopowders.

  17. Kinetic analysis on the non-isothermal degradation of plum stone waste by thermogravimetric analysis and integral master-plots method.

    Science.gov (United States)

    Ceylan, Selim

    2015-04-01

    In this study, pyrolysis of plum stone was investigated by thermogravimetric analysis in a nitrogen atmosphere at heating rates of 5, 10, 20 and 40 °C min(-1). Pyrolysis characteristics and the thermal-decomposition rate were significantly affected by variation in the heating rate. However, the heating rate slightly affected the total yield of the volatile matters. Activation energy of the pyrolysis reaction was evaluated by model-free methods, Friedman and Kissingere-Akahirae-Sunose. Results of the Master-Plots method indicated that the most probable reaction model function was the nth order reaction model function as f(x) = (1-x) (3.11), A = 8.02x10(12) under a mean activation energy of 150.61 kJ mol(-1). Proximate and ultimate analysis showed that plum stone can be considered as a favourable source for energy production owing to its low moisture and ash content, and high volatile matter ratio and moderate heating value. © The Author(s) 2015.

  18. Kinetic analysis of dechlorination and oxidation of PrOCl by using a non-isothermal TG method

    International Nuclear Information System (INIS)

    Yang, H.C.; Eun, H.C.; Cho, Y.Z.; Lee, H.S.; Kim, I.T.

    2009-01-01

    Thermal dechlorination and oxidation process of praseodymium oxychloride, PrOCl, was studied from the view point of reaction kinetics. On the basis of data of thermogravimetry under different oxygen partial pressures at various heating rates, a kinetic analysis was performed using an isoconversional method and a master plot method. The results of the isoconversional method of TG data suggested that the dechlorination and oxidation of PrOCl followed a single step with activation energy of 112.6 ± 3.4 kJ mol -1 , and from master plot methods, the reaction was described by a linear-contracting phase boundary reaction

  19. TG/FT-IR characterization of additives typically employed in EPDM formulations

    Directory of Open Access Journals (Sweden)

    Natália Beck Sanches

    2015-06-01

    Full Text Available AbstractThermogravimetric analysis coupled to Fourier transform infrared spectroscopy (TG/FT-IR is a very popular technique for rubbers characterization. It involves analyses of the base polymer and additives. Ethylene–propylene–diene (EPDM rubbers are frequently investigated by TG/FT-IR; however, the focus has been the degradation temperature range of the polymer. In this study, unvulcanized and vulcanized EPDM rubber and its additives were investigated by TG/FT-IR, without solvent extraction, and in a wide temperature range. Initially, the additives were individually characterized. TG/FT-IR identified the characteristic groups of all the additives analyzed and distinguished them from each other. Afterwards, unvulcanized and vulcanized EPDM rubbers were investigated without prior extraction.TG/FT-IR detected absorptions due to the additives tetramethylthiuram monosulfide and 2-mercaptobenzothiazole. Both of these sulfur-containing additives were present in the EPDM formulation at concentrations of 0.7 phr (0.63 wt %. The TG/FT-IR technique had some limitations, because not all the additives in EPDM rubber were detected. Paraffin oil, stearic acid and 2,2,4-trimethyl-1,2-dihydroquinoline functional groups were not observed in either the unvulcanized or vulcanized EPDM. Nevertheless, in addition to the ability of this method to detect sulfur-containing groups, the lack of a pre-extraction reduces the time and effort required for additive analysis in rubbers.

  20. Pyrolysis of biofuels of the future: Sewage sludge and microalgae – Thermogravimetric analysis and modelling of the pyrolysis under different temperature conditions

    International Nuclear Information System (INIS)

    Soria-Verdugo, Antonio; Goos, Elke; Morato-Godino, Andrés; García-Hernando, Nestor; Riedel, Uwe

    2017-01-01

    Highlights: • Pyrolysis of microalgae and sewage sludge is studied by thermogravimetric analysis. • Accurate values of the kinetic parameters of the pyrolysis reaction are reported. • Pyrolysis is modeled for parabolic and exponential temperature increases. • Estimations of the model are compared with experimental measurements in TGA. • Excellent agreement is reached between the model estimations and the experiments. - Abstract: The pyrolysis process of both microalgae and sewage sludge was investigated separately, by means of non-isothermal thermogravimetric analysis. The Distributed Activation Energy Model (DAEM) was employed to obtain the pyrolysis kinetic parameters of the samples, i.e. the activation energy E_a and the pre-exponential factor k_0. Nine different pyrolysis tests at different constant heating rates were conducted for each sample in a thermogravimetric analyzer (TGA) to obtain accurate values of the pyrolysis kinetic parameters when applying DAEM. The accurate values of the activation energy and the pre-exponential factor that characterize the pyrolysis reaction of Chlorella vulgaris and sewage sludge were reported, together with their associated uncertainties. The activation energy and pre-exponential factor for the C. vulgaris vary between 150–250 kJ/mol and 10"1"0–10"1"5 s"−"1 respectively, whereas values ranging from 200 to 400 kJ/mol were obtained for the sewage sludge activation energy, and from 10"1"5 to 10"2"5 s"−"1 for its pre-exponential factor. These values of E_a and k_0 were employed to estimate the evolution of the reacted fraction with temperature during the pyrolysis of the samples under exponential and parabolic temperature increases, more typical for the pyrolysis reaction of fuel particles in industrial reactors. The estimations of the relation between the reacted fraction and the temperature for exponential and parabolic temperature increases were found to be in good agreement with the experimental values

  1. Thermal transformation of bioactive caffeic acid on fumed silica seen by UV-Vis spectroscopy, thermogravimetric analysis, temperature programmed desorption mass spectrometry and quantum chemical methods.

    Science.gov (United States)

    Kulik, Tetiana V; Lipkovska, Natalia O; Barvinchenko, Valentyna M; Palyanytsya, Borys B; Kazakova, Olga A; Dudik, Olesia O; Menyhárd, Alfréd; László, Krisztina

    2016-05-15

    Thermochemical studies of hydroxycinnamic acid derivatives and their surface complexes are important for the pharmaceutical industry, medicine and for the development of technologies of heterogeneous biomass pyrolysis. In this study, structural and thermal transformations of caffeic acid complexes on silica surfaces were studied by UV-Vis spectroscopy, thermogravimetric analysis, temperature programmed desorption mass spectrometry (TPD MS) and quantum chemical methods. Two types of caffeic acid surface complexes are found to form through phenolic or carboxyl groups. The kinetic parameters of the chemical reactions of caffeic acid on silica surface are calculated. The mechanisms of thermal transformations of the caffeic chemisorbed surface complexes are proposed. Thermal decomposition of caffeic acid complex chemisorbed through grafted ester group proceeds via three parallel reactions, producing ketene, vinyl and acetylene derivatives of 1,2-dihydroxybenzene. Immobilization of phenolic acids on the silica surface improves greatly their thermal stability. Copyright © 2016 Elsevier Inc. All rights reserved.

  2. Thermogravimetric and kinetic study of methylolmelamine ...

    African Journals Online (AJOL)

    Some salient properties of cotton cellulose which requires it to be treated with additives to improve its versatility were examined taken into consideration, the molecular structure. Thermogravimetric analysis of the cotton fabric and the treated cotton fabric were carried out in an improvised muffled furnace. The result was in ...

  3. Thermogravimetric analysis, kinetic study, and pyrolysis-GC/MS analysis of 1,1'-azobis-1,2,3-triazole and 4,4'-azobis-1,2,4-triazole.

    Science.gov (United States)

    Jia, Chenhui; Li, Yuchuan; Zhang, Shujuan; Fei, Teng; Pang, Siping

    2018-03-01

    In general, the greater the number of directly linked nitrogen atoms in a molecule, the better its energetic performance, while the stability will be accordingly lower. But 1,1'-azobis-1,2,3-triazole (1) and 4,4'-azobis-1,2,4-triazole (2) show remarkable properties, such as high enthalpies of formation, high melting points, and relatively high stabilities. In order to rationalize this unexpected behavior of the two compounds, it is necessary to study their thermal decompositions and pyrolyses. Although a great deal of research has been focused on the synthesis and characterization of energetic materials with 1 and 2 as the backbone, a complete report on their fundamental thermodynamic parameters and thermal decomposition properties has not been published. Thermogravimetric-differential scanning calorimetry were used to obtain the thermal decomposition data of the title compounds. Kissinger and Ozawa-Doyle methods, the two selected non-isothermal methods, are presented for analysis of the solid-state kinetic data. Pyrolysis-gas chromatography/mass spectrometry was used to study the pyrolysis process of the title compounds. The DSC curves show that the thermal decompositions of 1 and 2 are at different heating rates involved a single exothermic process. The TG curves provide insight into the total weight losses from the compounds associated with this process. At different pyrolysis temperatures, the compositions and types of the pyrolysis products differ greatly and the pyrolysis reaction at 500 °C is more thorough than 400 °C. Apparent activation energies (E) and pre-exponential factors (lnA/s -1 ) are 291.4 kJ mol -1 and 75.53 for 1; 396.2 kJ mol -1 and 80.98 for 2 (Kissinger). The values of E are 284.5 kJ mol -1 for 1 and 386.1 kJ mol -1 for 2 (Ozawa-Doyle). The critical temperature of thermal explosion (T b ) is evaluated as 187.01 °C for 1 and 282.78 °C for 2. The title compounds were broken into small fragment ions under the pyrolysis conditions

  4. Thermogravimetric-Mass Spectrometric Study of the Pyrolysis Behavior of PVC

    Institute of Scientific and Technical Information of China (English)

    SUN Qing-lei; SHI Xin-gang; LIN Yun-liang; ZHU He; WANG Xiao; CHENG Chuan-ge; LIU Jian-hua

    2007-01-01

    The pyrolysis characteristics of PVC were systematically investigated using a Netzschne TG thermo-balance coupled to a quadrupole mass spectrometer. The pyrolysis conditions were 0.1 MPa of Ar, a heating rate of 10 ℃/min and a final temperature of 1000 ℃. Both the thermogravimetric properties and the simultaneous evolution of gaseous products during pyrolysis were studied. The TG/DTG results showed that as the pyrolysis temperature increases the weight loss and weight loss rate of PVC increases. Near 412 ℃ the weight loss rate attained its peak value. At higher temperatures the rate of loss gradually decreases. The gases evolved during thermogravimetric analysis were analyzed by a mass spectrometer, monitoring the relative intensity of HCl, C6H6, light hydrocarbon and chlorine-containing gases. The evolution curves showed that HCl, C6H6, light hydrocarbon and chlorine-containing gases all peak at about 416 ℃. This is consistent with the fact that the weight loss curves also peak at about 412 ℃. The extensive HCl evolution is consistent with the high chlorine content of PVC. The formation of these gases can be explained by considering these reactions: dehydrochlorination, intramolecular cyclization and the addition of HCl to unsaturated hydrocarbons.

  5. Thermogravimetric study of the reaction of uranium oxides with fluorine

    International Nuclear Information System (INIS)

    Komura, Motohiro; Sato, Nobuaki; Kirishima, Akira; Tochiyama, Osamu

    2008-01-01

    Thermogravimetric study of the reaction of uranium oxides with fluorine was conducted by TG-DTA method using anti-corrosion type differential thermobalance. When UO 2 was heated from R.T. to 500 deg. C in 5% F 2 /He atmosphere, the weight increase appeared at ca. 250 deg. C with an exothermic peak. Then the weight decreased slightly with a small exothermic peak followed by the complete volatilization with a large exothermic peak at ca. 350 deg. C. At a flow rate of 15, 30, 60 ml min -1 , there seemed to be no significant change for the fluorination of UO 2 . With the different heating rates of 1, 2, 5 and 10 deg. C min -1 , the fluorination peak shifted to higher temperature with increasing heating rates. For the comparison with thermogravimetric results, phase analysis by XRD method was conducted for the products obtained at different temperatures. At 260 deg. C, the product was UO 2 with a small amount of the intermediate compound, UO 2 F. The amount of this compound increased with increasing temperature up to 320 deg. C. Then another phase of UO 2 F 2 appeared at 340 deg. C but it was immediately fluorinated to the volatile fluoride. When U 3 O 8 was used as a starting material, it was found that the steep weight decrease peak appeared at ca. 350 deg. C and the uranium volatilized completely. This result suggests that fluorination of U 3 O 8 occurs at this temperature forming UF 6 . Uranium trioxide showed the similar fluorination behavior to that of U 3 O 8

  6. Análises de protocolos de braquiterapia, por alta taxa de dose, do controle de qualidade de alguns serviços locais, baseados no TG40, TG56 e ARCAL XXX Analysis of the high dose rate brachytherapy protocols of quality assurance programs of some local services, based on TG40, TG56 and ARCAL XXX.

    Directory of Open Access Journals (Sweden)

    Carmen S. Guzmán Calcina

    2001-08-01

    Full Text Available A braquiterapia por alta taxa de dose está recebendo atenção considerável na maioria dos países. Por isso, nos serviços que utilizam este equipamento exige-se que o desenvolvimento de um programa de controle de qualidade seja cada vez mais rigoroso, para garantir não apenas a segurança aos pacientes, mas também aos operadores e demais envolvidos. Este trabalho tem por objetivos fazer um levantamento dos tipos de testes para um equipamento de braquiterapia por alta taxa de dose, propostos pelos protocolos oficiais publicados (TG40, TG56 e ARCAL XXX e avaliar os tipos de testes que atualmente são realizados por alguns serviços de radioterapia, comparando-os com aqueles apresentados nos protocolos citados. Das análises feitas, observou-se que: a quanto aos protocolos oficiais, o TG56 é mais completo que o TG40 e o ARCAL XXX; b quanto às instituições analisadas, estas em geral se basearam no TG56 para elaborar seus próprios protocolos, os quais demonstraram ter também concordância com os outros já citados. Nestes protocolos, a inexistência dos testes anuais foi notada, o que pode ser explicado por sua aparição nas freqüências trimestral e semestral. Do produto deste estudo são apresentadas tabelas dos tipos de testes com suas respectivas freqüências de utilização, das quais um protocolo pode ser inferido para auxiliar na implementação, pelo menos, dos tipos de testes de controle de qualidade básicos e indispensáveis para o equipamento, garantindo, assim, um tratamento adequado aos pacientes e uma melhor segurança ao pessoal envolvido e, conseqüentemente, assegurando a garantia de qualidade na braquiterapia por alta taxa de dose.High dose rate brachytherapy has been increasingly recognized in most countries, and radiotherapy services using this equipment are encouraged to have a very efficient quality assurance program to ensure protection for patients, workers and other personnel involved. The objective of this

  7. Characterization of thermal reaction of aluminum/copper (II) oxide/poly(tetrafluoroethene) nanocomposite by thermogravimetric analysis, differential scanning calorimetry, mass spectrometry and X-ray diffraction

    International Nuclear Information System (INIS)

    Li, Xiangyu; Yang, Hongtao; Li, Yan-chun

    2015-01-01

    Highlights: • The thermal reaction properties of the Al/CuO/PTFE nanocomposite were investigated. • The Al/PTFE and CuO/PTFE nanocomposites were prepared and tested for comparison. • TG/DSC–MS and XRD analysis were performed. • PTFE is oxidizing Al and reducing CuO during the thermal decomposition. - Abstract: The application of fluoropolymers as reactive agent in energetic materials have attracted significant interest recently. In this study, the thermal reaction properties of the aluminum nanoparticles/copper (II) oxide nanoparticles/poly(tetrafluoroethene) (Al-NPs/CuO-NPs/PTFE) nanocomposite (mass ratio of Al-NPs/CuO-NPs/PTFE = 20/60/20) were investigated by means of thermogravimetry/differential scanning calorimetry–mass spectrometry (TG/DSC–MS) and X-ray diffraction (XRD) analyses. The Al-NPs/PTFE (mass ratio of Al-NPs/PTFE = 50/50) and CuO-NPs/PTFE (mass ratio of CuO-NPs/PTFE = 75/25) nanocomposites were also prepared and tested for comparison. It is observed that PTFE is acting as both oxidizer and reducer during the thermal decomposition process of Al-NPs/CuO-NPs/PTFE nanocomposites. Before 615 °C, PTFE is oxidized by CuO-NPs and oxidizing Al-NPs, resulting mass reduction. After 615 °C, the excessive aluminum and copper (I)/copper (II) oxide will proceed the exothermic condensed phase reaction.

  8. A thermogravimetric analysis (TGA) method developed for estimating the stoichiometric ratio of solid-state {alpha}-cyclodextrin-based inclusion complexes

    Energy Technology Data Exchange (ETDEWEB)

    Bai, Yuxiang; Wang, Jinpeng; Bashari, Mohanad; Hu, Xiuting [The State Key Laboratory of Food Science and Technology, School of Food Science and Technology, Jiangnan University, Wuxi 214122 (China); Feng, Tao [School of Perfume and Aroma Technology, Shanghai Institute of Technology, Shanghai 201418 (China); Xu, Xueming [The State Key Laboratory of Food Science and Technology, School of Food Science and Technology, Jiangnan University, Wuxi 214122 (China); Jin, Zhengyu, E-mail: jinlab2008@yahoo.com [The State Key Laboratory of Food Science and Technology, School of Food Science and Technology, Jiangnan University, Wuxi 214122 (China); Tian, Yaoqi, E-mail: yqtian@jiangnan.edu.cn [The State Key Laboratory of Food Science and Technology, School of Food Science and Technology, Jiangnan University, Wuxi 214122 (China)

    2012-08-10

    Highlights: Black-Right-Pointing-Pointer We develop a TGA method for the measurement of the stoichiometric ratio. Black-Right-Pointing-Pointer A series of formulas are deduced to calculate the stoichiometric ratio. Black-Right-Pointing-Pointer Four {alpha}-CD-based inclusion complexes were successfully prepared. Black-Right-Pointing-Pointer The developed method is applicable. - Abstract: An approach mainly based on thermogravimetric analysis (TGA) was developed to evaluate the stoichiometric ratio (SR, guest to host) of the guest-{alpha}-cyclodextrin (Guest-{alpha}-CD) inclusion complexes (4-cresol-{alpha}-CD, benzyl alcohol-{alpha}-CD, ferrocene-{alpha}-CD and decanoic acid-{alpha}-CD). The present data obtained from Fourier transform-infrared (FT-IR) spectroscopy showed that all the {alpha}-CD-based inclusion complexes were successfully prepared in a solid-state form. The stoichiometric ratios of {alpha}-CD to the relative guests (4-cresol, benzyl alcohol, ferrocene and decanoic acid) determined by the developed method were 1:1, 1:2, 2:1 and 1:2, respectively. These SR data were well demonstrated by the previously reported X-ray diffraction (XRD) method and the NMR confirmatory experiments, except the SR of decanoic acid with a larger size and longer chain was not consistent. It is, therefore, suggested that the TGA-based method is applicable to follow the stoichiometric ratio of the polycrystalline {alpha}-CD-based inclusion complexes with smaller and shorter chain guests.

  9. A thermogravimetric analysis (TGA) method developed for estimating the stoichiometric ratio of solid-state α-cyclodextrin-based inclusion complexes

    International Nuclear Information System (INIS)

    Bai, Yuxiang; Wang, Jinpeng; Bashari, Mohanad; Hu, Xiuting; Feng, Tao; Xu, Xueming; Jin, Zhengyu; Tian, Yaoqi

    2012-01-01

    Highlights: ► We develop a TGA method for the measurement of the stoichiometric ratio. ► A series of formulas are deduced to calculate the stoichiometric ratio. ► Four α-CD-based inclusion complexes were successfully prepared. ► The developed method is applicable. - Abstract: An approach mainly based on thermogravimetric analysis (TGA) was developed to evaluate the stoichiometric ratio (SR, guest to host) of the guest–α-cyclodextrin (Guest-α-CD) inclusion complexes (4-cresol-α-CD, benzyl alcohol-α-CD, ferrocene-α-CD and decanoic acid-α-CD). The present data obtained from Fourier transform-infrared (FT-IR) spectroscopy showed that all the α-CD-based inclusion complexes were successfully prepared in a solid-state form. The stoichiometric ratios of α-CD to the relative guests (4-cresol, benzyl alcohol, ferrocene and decanoic acid) determined by the developed method were 1:1, 1:2, 2:1 and 1:2, respectively. These SR data were well demonstrated by the previously reported X-ray diffraction (XRD) method and the NMR confirmatory experiments, except the SR of decanoic acid with a larger size and longer chain was not consistent. It is, therefore, suggested that the TGA-based method is applicable to follow the stoichiometric ratio of the polycrystalline α-CD-based inclusion complexes with smaller and shorter chain guests.

  10. Characterization of Synthesized and Commercial Forms of Magnesium Stearate Using Differential Scanning Calorimetry, Thermogravimetric Analysis, Powder X-Ray Diffraction, and Solid-State NMR Spectroscopy.

    Science.gov (United States)

    Delaney, Sean P; Nethercott, Matthew J; Mays, Christopher J; Winquist, Nickolas T; Arthur, Donia; Calahan, Julie L; Sethi, Manish; Pardue, Daniel S; Kim, Junghyun; Amidon, Gregory; Munson, Eric J

    2017-01-01

    Magnesium stearate is the salt of a complex mixture of fatty acids, with the majority being stearate and palmitate. It has multiple crystalline forms and, potentially, an amorphous form. Magnesium stearate is used in the pharmaceutical manufacturing industry as a powder lubricant, and typically is added at low levels (∼1%) during the manufacturing process and blended for a relatively short time (∼5 min). Proper levels and mixing times are needed, as too short a mixing time or too small a quantity will result in improper lubrication, and too much can negatively impact dissolution rates. The complex mixture of multiple fatty acids and crystalline forms in magnesium stearate leads to variability between commercial sources, and switching between sources can impact both the amount of lubricant and mixing time needed for proper lubrication. In order to better understand the complex nature of magnesium stearate, a variety of analytical techniques were used to characterize both synthesized and commercial magnesium stearate samples. The results show that correlation among differential scanning calorimetry, thermogravimetric analysis, solid-state NMR spectroscopy, and other techniques provides a unique insight into the forms of magnesium stearate. Finally, the ability to monitor form changes of magnesium stearate in an intact tablet using solid-state NMR spectroscopy is shown. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

  11. Characterization of the Sublimation and Vapor Pressure of 2-(2-Nitrovinyl) Furan (G-0) Using Thermogravimetric Analysis: Effects of Complexation with Cyclodextrins.

    Science.gov (United States)

    Ruz, Vivian; González, Mirtha Mayra; Winant, Danny; Rodríguez, Zenaida; Van den Mooter, Guy

    2015-08-19

    In the present work, the sublimation of crystalline solid 2-(2-nitrovinyl) furan (G-0) in the temperature range of 35 to 60 °C (below the melting point of the drug) was studied using thermogravimetric analysis (TGA). The sublimated product was characterized using Fourier-transformed-infrared spectroscopy (FT-IR) and thin layer chromatography (TLC). The sublimation rate at each temperature was obtained using the slope of the linear regression model and followed apparent zero-order kinetics. The sublimation enthalpy from 35 to 60 °C was obtained from the Eyring equation. The Gückel method was used to estimate the sublimation rate and vapor pressure at 25 °C. Physical mixtures, kneaded and freeze-dried complexes were prepared with 2-hydroxypropyl-β-cyclodextrin (HP-β-CD) and sulfobutyl ether-β-cyclodextrin (SBE-β-CD) and analyzed using isothermal TGA at 50 °C. The complexation contributed to reducing the sublimation process. The best results were achieved using freeze-dried complexes with both cyclodextrins.

  12. Kinetic model of the thermal pyrolysis of chrome tanned leather treated with NaOH under different conditions using thermogravimetric analysis.

    Science.gov (United States)

    Bañón, E; Marcilla, A; García, A N; Martínez, P; León, M

    2016-02-01

    The thermal decomposition of chrome tanned leather before and after a soaking treatment with NaOH was studied using thermogravimetric analysis (TGA). The effect of the solution concentration (0.2M and 0.5M) and the soaking time (5min and 15min) was evaluated. TGA experiments at four heating rates (5, 10, 15 and 20°Cmin(-1)) were run in a nitrogen atmosphere for every treatment condition. A kinetic model was developed considering the effect of the three variables studied, i.e.: the NaOH solution concentration, the soaking time and the heating rate. The proposed model for chrome tanned leather pyrolysis involves a set of four reactions, i.e.: three independent nth order reactions, yielding the corresponding products and one of them undergoing a successive cero order reaction. The model was successfully applied simultaneously to all the experimental data obtained. The evaluation of the kinetic parameters obtained (activation energy, pre-exponential factor and reaction order) allowed a better understanding of the effect of the alkali treatment on these wastes. Copyright © 2015 Elsevier Ltd. All rights reserved.

  13. A Study of the Oxidation Behaviour of Pile Grade A (PGA) Nuclear Graphite Using Thermogravimetric Analysis (TGA), Scanning Electron Microscopy (SEM) and X-Ray Tomography (XRT).

    Science.gov (United States)

    Payne, Liam; Heard, Peter J; Scott, Thomas B

    2015-01-01

    Pile grade A (PGA) graphite was used as a material for moderating and reflecting neutrons in the UK's first generation Magnox nuclear power reactors. As all but one of these reactors are now shut down there is a need to understand the residual state of the material prior to decommissioning of the cores, in particular the location and concentration of key radio-contaminants such as 14C. The oxidation behaviour of unirradiated PGA graphite was studied, in the temperature range 600-1050°C, in air and nitrogen using thermogravimetric analysis, scanning electron microscopy and X-ray tomography to investigate the possibility of using thermal degradation techniques to examine 14C distribution within irradiated material. The thermal decomposition of PGA graphite was observed to follow the three oxidation regimes historically identified by previous workers with limited, uniform oxidation at temperatures below 600°C and substantial, external oxidation at higher temperatures. This work demonstrates that the different oxidation regimes of PGA graphite could be developed into a methodology to characterise the distribution and concentration of 14C in irradiated graphite by thermal treatment.

  14. INFRARED SPECTRA, THERMOGRAVIMETRIC ANALYSIS AND ...

    African Journals Online (AJOL)

    Preferred Customer

    2Department of Pesticides Formulation, Central Agricultural Pesticides ... a number of other Fusarium species are able to degrade benzoxazolinone compounds to products which are less inhibitory to fungal growth and also important ...

  15. Compositional characterization of carbon electrode material: A study using simultaneous TG-DTA-FTIR

    International Nuclear Information System (INIS)

    Raje, Naina; Aacherekar, Darshana A.; Reddy, A.V.R.

    2009-01-01

    Present work describes the application of thermal methods, especially the evolved gas analysis (EGA) for the compositional characterization of carbon electrode material with respect to its organic, amorphous and graphitic carbon content. Trace levels of organic carbon present in the amorphous carbon samples were determined qualitatively by using FTIR absorption spectroscopy. Amorphous and graphitic carbon content in synthetic mixture samples were determined quantitatively using simultaneous TG-DTA-FTIR measurements. FTIR system was calibrated using the measured absorption signal of the evolved carbon dioxide due to the decomposition of cadmium carbonate. Inter-comparison studies using TG-FTIR measurements show that simultaneous FTIR spectroscopy is an effective complementary quantitative measurement technique for thermogravimetric analysis involving the complex decomposition reaction processes.

  16. Investment casting using multi-jet modelling patterns: the thermogravimetric analysis of visijet® SR200 UV curable acrylate plastic

    International Nuclear Information System (INIS)

    Hafsa, M N; Ibrahim, M; Sharif, S

    2013-01-01

    Rapid Prototyping (RP) technology is actively studied to be implemented in Investment Casting (IC) process. Nowadays RP techniques are studied for their feasibility as IC master patterns, in terms of pattern collapsibility and drainage during burnout. The purpose of the study is to determine the characteristic of Visijet® SR200 acrylate material during burnout process. Traditional IC patterns made from wax have properties that limit their application in precision casting, especially for parts with thin geometries that readily break or deform when handled or dipped in the refractory slurry. Furthermore, it is not economical when producing a small number of parts. Non wax patterns fabricated for IC process, revealed ceramic shell cracking due to excessive thermal expansions, incomplete collapsibility of pattern during burnout, residual ash and poor surface finish. Thermogravimetric analysis (TGA) was used to measured the weight loss of acrylate material as the temperature was increased. TGA measured the change of material's mass as it is heated. It represents the decomposition temperature after being subjected to varying temperatures, as well as the amount of residual ash. In this experiment, the temperature range was from 20°C to 700°C with 5°C increment. Experiment results show the values of material's optimum reaction temperature and decomposing temperature of Visijet® SR200 acrylate. The percentages of remaining materials were also monitored throughout the process to obtain the amount of residual ash. All of the temperature values obtained is a resemblance for the actual burnout process and can be used as references

  17. Thermogravimetric studies of vapour-aerosol interactions

    International Nuclear Information System (INIS)

    Henshaw, J.; Newland, M.S.; Wood, S.J.

    1991-01-01

    Thermogravimetric analysis has been used to study the interaction of iodine vapour with cadmium, silver and manganese monoxide substrates. These studies have demonstrated the importance of time-dependence data on reaction rates. Iodine did not react with manganese monoxide (as expected from thermodynamic considerations); however, extensive reaction did occur with silver and cadmium. Two rate limiting mechanisms were observed: mass transfer of iodine molecules from the gas phase (leading to linear reaction rates) and parabolic kinetics (ie inversely proportional to the extent of reaction) when the rate was limited by a diffusion process through the reaction product. (author)

  18. Análise TG-ROC de testes de imunofluorescência no diagnóstico de leishmaniose visceral canina Análisis TG-ROC de pruebas de inmunofluorescencia en el diagnóstico de leishmaniasis visceral canina TG-ROC analysis of immunofluorescence assays in canine visceral leishmaniasis diagnosis

    Directory of Open Access Journals (Sweden)

    Rita Maria da Silva

    2009-12-01

    costo-beneficio.OBJECTIVE: To analyze the accuracy of the diagnosis of two protocols of indirect immunofluorescence assays for canine visceral leishmaniasis. METHODS: Dogs from the seroepidemiological survey conducted in an endemic area of the cities of Araçatuba and Andradina, in Northwestern São Paulo state, in 2003, and in a non-endemic area of the metropolitan region of São Paulo, were used to assess two protocols of indirect immunofluorescence assay (IFA for leishmaniasis: one using a Leishmania major heterologous antigen (IFA-BM and another using a Leishmania chagasi homologous antigen (IFA-CH. Two-graph receiver operating characteristic (TG-ROC analysis was used to estimate accuracy. TG-ROC analysis compared 1:20 dilution readings of the homologous antigen (IFA-CH, considered as reference test, with IFA-BM dilutions (heterologous antigen. RESULTS: The 1:20 dilution used in the IFA-CH test showed the best contingency coefficient (0.755 and the highest strength of association between the two variables studied (chi-square=124.3. Thus, it was considered the test reference dilution in comparisons with different IFA-BM test dilutions. The best IFA-BM results were obtained from 1:40 dilutions with the best contingency coefficient (0.680 and highest strength of association (chi-square=80.8. With the change in the cut-off point, recommended for the IFA-BM 1:40 dilution in this analysis, the specificity parameter value rose from 57.5% to 97.7%, even though the 1:80 dilution showed the best sensitivity estimate (80.2%, with the new cut-off point. CONCLUSIONS: TG-ROC analysis can provide important information about diagnostic tests, in addition to offering suggestions on cut-off points that can improve test sensitivity and specificity estimates and assessing these tests in terms of the best cost-benefit ratio.

  19. Thermogravimetric evaluation of the suitability of precursors for MOCVD

    International Nuclear Information System (INIS)

    Kunte, G V; Shivashankar, S A; Umarji, A M

    2008-01-01

    A method based on the Langmuir equation for the estimation of vapour pressure and enthalpy of sublimation of subliming compounds is described. The variable temperature thermogravimetric/differential thermogravimetric (TG/DTG) curve of benzoic acid is used to arrive at the instrument parameters. Employing these parameters, the vapour pressure–temperature curves are derived for salicylic acid and camphor from their TG/DTG curves. The values match well with vapour pressure data in the literature, obtained by effusion methods. By employing the Clausius–Clapeyron equation, the enthalpy of sublimation could be calculated. Extending the method further, two precursors for metal-organic chemical vapour deposition (MOCVD) of titanium oxide bis-isopropyl bis tert-butyl 2-oxobutanoato titanium, Ti(O i Pr) 2 (tbob) 2 , and bis-oxo-bis-tertbutyl 2-oxobutanoato titanium, [TiO(tbob) 2 ] 2 , have been evaluated. The complex Ti(O i Pr) 2 (tbob) 2 is found to be a more suitable precursor. This approach can be helpful in quickly screening for the suitability of a compound as a CVD precursor

  20. In silico analysis and gene expression of TgNAC01 transcription factor involved in xylogenesis and abiotic stress in Tectona grandis.

    Directory of Open Access Journals (Sweden)

    Vladimir Camel Paucar

    2017-09-01

    Full Text Available Secondary xylem is the most abundant component of plant biomass. Therefore, knowing the genes that regulate its formation would help to design strategies for wood genetic improvement. Thus, the objective of this work was to perform computational analysis of the primary and secondary structure of the TgNAC01 transcription factor (FT of Tectona grandis, and to evaluate its evolutionary history, conserved domains and gene expression in lignified tissues of 12 and 60 years. For this, an ion-electron interaction potential (IEP was evaluated using the information-spectrum method (IEM using the R-Project and SFAPS library, followed by structural modeling using the MODELLER software and visualized by PyMol program. In addition, the analysis of multiple sequence alignment and phylogeny was performed using Bioedit and MrBayes software, respectively. We also evaluated the qRT-PCR levels of TgNAC01. As results, it was found that TgNAC01 maintains a twisted antiparallel β-sheet structure, which is compacted against an α-helix in the N-terminal region, having three α-helix domains and seven folded β-domains. Also, through the IEM, it was demonstrated that it has about five biological functions, and mutations on amino acids with higher IEP, which leads to evolutions on genetic regulation networks. Finally, the FT TgNAC01 plays an esential role in the organization and development of the parts that make up the sapwood, such as the radial cells of the cambial zone, the vessels, fibers and the growth rings.

  1. Thermogravimetric study of vinpocetine suppository

    Directory of Open Access Journals (Sweden)

    N. А. Nаgоrnaya

    2014-02-01

    Full Text Available Introduction. Development of technology is the one of the main stage in creation of new medications. Technological process of suppository manufacturing includes sufficiently long thermoprocessing during suppository base making, addition of the active substances and homogenisation. This makes risk of chemical and physical transformations of active substances and excipients in suppository which can be destroyed and changed pharmacologicaly. Use of thermogravimetric analyses in pharmaceutical technology allows to study possibility of chemical interactions of components in the wide range of temperature. The aim of this work was to study thermoprocessing effects on suppository base with vinpocetine in temperature range of technological process of suppository manufacturing. Object. Vinpocetine rectal suppository (with 0,5% of surface-active substances, active substance (vinpocetine and excipients (twin 80, cacao oil were used as the objects of thermogravimetric investigation. Thermogravimetric analyses was carried out on the derivatograph «Shimadzu DTG-60» (Japan with the platinum-rhodium thermocouple by heating from 25°C to 200°C in the aluminium crucible. α-Al2O3 was used as standard. Heating speed was 10ºС in minute. Model mass was 14,23 – 34,4 mg. Conclusions. It was established that cacao oil is thermolabile substance with melting temperature 41,32 ºС. Surface-active substance twin 80 displays thermostability from 30 tо 100ºС. Vinpocetine derivatogramme confirmed its thermostability in temperature range from 30 tо 154 ºС. Derivatogramme of vinpocetine rectal suppository 0,01 and suppository base displayed the absence of critical temperature lower 100ºС. Insignificant mass loss (0,21% shows that fact. Investigation of composition over 100ºС wasn’t carried out because these temperatures aren’t used in technological process of suppository manufacturing. Presence of thermal effects on derivatogramme of vinpocetine rectal

  2. Automation of a thermogravimetric equipment

    International Nuclear Information System (INIS)

    Mussio, L.; Castiglioni, J.; Diano, W.

    1987-01-01

    A low cost automation of some instruments by means of simple electronic circuits and a microcomputer Apple IIe. type is discussed. The electronic circuits described are: a) a position detector including phototransistors connected as differential amplifier; b) a current source that, using the error signal of the position detector, changes the current through the coil of an electromagnetic balance to restore its zero position; c) a proportional temperature controller, zero volt switching to drive a furnace to a desired temperature; d) an interface temperature regulator-microcomputer to control the temperature regulator by software; e) a multiplexer for an analog input of a commercial interface. Those circuits are applied in a thermogravimetric equipment used also for vapours adsorption. A program in block diagram form is included and is able to record change of mass, time, furnace temperature and to drive the temperature regulator in order to have the heating rates or the temperature plateaux needed for the experiment. (author) [pt

  3. SU-F-T-458: Tracking Trends of TG-142 Parameters Via Analysis of Data Recorded by 2D Chamber Array

    Energy Technology Data Exchange (ETDEWEB)

    Alexandrian, A; Kabat, C; Defoor, D; Saenz, D; Rasmussen, K; Kirby, N; Gutierrez, A; Papanikolaou, N; Stathakis, S [University of Texas HSC SA, San Antonio, TX (United States)

    2016-06-15

    Purpose: With increasing QA demands of medical physicists in clinical radiation oncology, the need for an effective method of tracking clinical data has become paramount. A tool was produced which scans through data automatically recorded by a 2D chamber array and extracts relevant information recommended by TG-142. Using this extracted information a timely and comprehensive analysis of QA parameters can be easily performed enabling efficient monthly checks on multiple linear accelerators simultaneously. Methods: A PTW STARCHECK chamber array was used to record several months of beam outputs from two Varian 2100 series linear accelerators and a Varian NovalisTx−. In conjunction with the chamber array, a beam quality phantom was used to simultaneously to determine beam quality. A minimalist GUI was created in MatLab that allows a user to set the file path of the data for each modality to be analyzed. These file paths are recorded to a MatLab structure and then subsequently accessed by a script written in Python (version 3.5.1) which then extracts values required to perform monthly checks as outlined by recommendations from TG-142. The script incorporates calculations to determine if the values recorded by the chamber array fall within an acceptable threshold. Results: Values obtained by the script are written to a spreadsheet where results can be easily viewed and annotated with a “pass” or “fail” and saved for further analysis. In addition to creating a new scheme for reviewing monthly checks, this application allows for able to succinctly store data for follow up analysis. Conclusion: By utilizing this tool, parameters recommended by TG-142 for multiple linear accelerators can be rapidly obtained and analyzed which can be used for evaluation of monthly checks.

  4. Thermogravimetric measurements of liquid vapor pressure

    International Nuclear Information System (INIS)

    Rong Yunhong; Gregson, Christopher M.; Parker, Alan

    2012-01-01

    Highlights: ► Rapid determination of vapor pressure by TGA. ► Demonstration of limitations of currently available approaches in literature. ► New model for vapor pressure assessment of small size samples in TGA. ► New model accounts for vapor diffusion and sample geometry and measures vapor pressure normally within 10%. - Abstract: A method was developed using thermo-gravimetric analysis (TGA) to determine the vapor pressure of volatile liquids. This is achieved by measuring the rate of evaporation (mass loss) of a pure liquid contained within a cylindrical pan. The influence of factors like sample geometry and vapor diffusion on evaporation rate are discussed. The measurement can be performed across a wide range of temperature yielding reasonable results up to 10 kPa. This approach may be useful as a rapid and automatable method for measuring the volatility of flavor and fragrance raw materials.

  5. Thermogravimetric study of rare earth concentrates

    International Nuclear Information System (INIS)

    Delyagejd, V.V.; Anisimova, V.N.; Eremenko, Z.V.; Kutsev, V.S.

    1974-01-01

    Methods of thermogravimetric, chemical and phase analysis were used in measuring the concentration of rare-earth elements of different origins. At temperatures 400-800 deg C a gradual decomposition of fluorocarbonates takes place leading to the formation of derivatives of corresponding oxides and oxyfluorides. For concentrates containing siderite the process takes place at 550-600 deg C followed by oxidation of bivalent iron into trivalent state. Reaction of rare-earth elements with sodium carbonate and the increase in the concentration of the latter results in a narrowing down of the interval of temperatures at which decomposition takes place. Under these conditions an intense reaction and a fusion take place leading to the formation of eutectic at 500-600 deg C and further synthesis of sodium fluoride and oxyfluoride derivatives of calcium and rare-earth elements

  6. Biomechanical assays amniotic membrane preserved in glycerol correlating with optical coherence tomography (OCT) and thermal gravimetric analysis (TG)

    International Nuclear Information System (INIS)

    Soares, Fernando Augusto N.; Santin, Stefany P.; Martino Junior, Antonio C.; Machado, Luci Diva B.; Freitas, Anderson Z.; Mathor, Monica B.

    2013-01-01

    Young's modulus, the OCT technique, to generate high-resolution images in real time being a non-destructive technique, thermogravimetry (TG) assessing the amount of water and rate of water output membranes after treatment with ionizing radiation, relating the possible changes with non-irradiated tissue. However the results of the tensile test had the same behavior compared to the values of total attenuation coefficient by OCT, in addition the dehydration rate analyzed by TG had no statistically significant variation to some radiation doses. (author)

  7. Biomechanical assays amniotic membrane preserved in glycerol correlating with optical coherence tomography (OCT) and thermal gravimetric analysis (TG)

    Energy Technology Data Exchange (ETDEWEB)

    Soares, Fernando Augusto N.; Santin, Stefany P.; Martino Junior, Antonio C.; Machado, Luci Diva B.; Freitas, Anderson Z.; Mathor, Monica B., E-mail: fernandonevessoares@yahoo.com.br [Instituto de Pesquisas Energetias Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2013-07-01

    Young's modulus, the OCT technique, to generate high-resolution images in real time being a non-destructive technique, thermogravimetry (TG) assessing the amount of water and rate of water output membranes after treatment with ionizing radiation, relating the possible changes with non-irradiated tissue. However the results of the tensile test had the same behavior compared to the values of total attenuation coefficient by OCT, in addition the dehydration rate analyzed by TG had no statistically significant variation to some radiation doses. (author)

  8. Thermogravimetric investigations of cream with minoxidil

    Directory of Open Access Journals (Sweden)

    I. V. Gnitko

    2016-12-01

    Full Text Available Minoxidil is one of the most effective and modern medications, which is used in modern trichology for hair growth stimulation in case of androgenic and other forms of alopecia. Clinical effect of this substance is caused by the intensification of metabolic processes in the skin due to intensification of microcirculation. For local application domestic dermatology uses imported minoxidil medicines in form of alcohol-water lotions and aerosols. The use of semisolid dosage form with minoxidil for external administration will allow to increase its efficacy and will widen the arsenal of domestic pharmacotherapeutic agents for hair growth stimulation. Rational composition of minoxidil semisolid dosage form for external use with 2% of active substance has been developed at the Department of Medicinal Preparations Technology, Zaporozhye State Medical University as a result of complex physical-chemical, microbiological and biopharmaceutical investigations. The aim of this work is the study of thermal treatment effects of cream-mask with minoxidil for external use over the temperature range, which is used in technological process of this dosage form manufacturing. Materials and methods. Cream with 2% of minoxidil on the emulsion base and its excipients have been used as the object for the thermogravimetric investigations. Thermogravimetric analysis has been carried out on the derivatograph «Shimadzu DTG-60», Japan, with the platinum and platinum-rhodium thermopair with samples’ heating in aluminium crucibles from 25 to 200ºС. Results. According to thermogravimetric experimental data minoxidil is a thermal stable substance from 26 to 240ºС. During experimental process insignificant endothermic effect was determined at 191,72ºС. However the mass of the example to the end of experiment practically didn’t change (decrease on 0,32%. Thermal effects on the derivatogram of minoxidil emulsion cream match with thermal effects of the base components and

  9. [Morphological analysis of the hippocampal region associated with an innate behaviour task in the transgenic mouse model (3xTg-AD) for Alzheimer disease].

    Science.gov (United States)

    Orta-Salazar, E; Feria-Velasco, A; Medina-Aguirre, G I; Díaz-Cintra, S

    2013-10-01

    Different animal models for Alzheimer disease (AD) have been designed to support the hypothesis that the neurodegeneration (loss of neurons and synapses with reactive gliosis) associated with Aβ and tau deposition in these models is similar to that in the human brain. These alterations produce functional changes beginning with decreased ability to carry out daily and social life activities, memory loss, and neuropsychiatric disorders in general. Neuronal alteration plays an important role in early stages of the disease, especially in the CA1 area of hippocampus in both human and animal models. Two groups (WT and 3xTg-AD) of 11-month-old female mice were used in a behavioural analysis (nest building) and a morphometric analysis of the CA1 region of the dorsal hippocampus. The 3xTg-AD mice showed a 50% reduction in nest quality associated with a significant increase in damaged neurons in the CA1 hippocampal area (26%±6%, Pde Neurología. Published by Elsevier Espana. All rights reserved.

  10. Air oxidation of Zr65Cu17.5Ni10Al7.5 in its amorphous and supercooled liquid states, studied by thermogravimetric analysis

    International Nuclear Information System (INIS)

    Dhawan, A.; Sharma, S.K.; Raetzke, K.; Faupel, F.

    2003-01-01

    The oxidation behaviour of the bulk amorphous alloy Zr 65 Cu 17.5 Ni 10 Al 7.5 was studied in air at various temperatures in the temperature range 591-732 K using a thermogravimetric analyser (TGA). The oxidation kinetics of the alloy obeys the parabolic rate law showing two different linear regions (in the plots of mass gain versus square root of oxidation time) which are attributed to the amorphous and the supercooled liquid states of the alloy. The value of the activation energy Q for the amorphous state as calculated from the temperature dependence of the rate constants is found to be 1.80±0.1 eV and the corresponding value obtained for the supercooled liquid state is 1.20±0.1 eV. It is suggested that the rate controlling process during oxidation of the amorphous state is the back-diffusion of Ni, and possibly Cu also, while the oxidation in the supercooled liquid state is dominated by the inward diffusion of oxygen. (copyright 2003 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  11. Preparation, thermogravimetric study and infrared spectra of rare earth acetates

    International Nuclear Information System (INIS)

    Graehlert, X.; Starke, M.

    1992-01-01

    The anhydrous and the hydrated acetates of Ho, Er, Tm, Yb and Lu have been prepared. The compounds obtained have been investigated by thermogravimetric analysis and infrared spectroscopy. The thermal decomposition of the rare earth acetates may proceed via various steps. It depends on both the number of crystal water molecules in the acetates and the rare earth element's behaviour. (orig.)

  12. Association between MDM2 SNP309 T>G polymorphism and the risk of bladder cancer: new data in a Chinese population and an updated meta-analysis

    Directory of Open Access Journals (Sweden)

    Xie LG

    2015-12-01

    Full Text Available Linguo Xie,1,2,* Yan Sun,2,* Tao Chen,1,2,* Dawei Tian,1,2 Yujuan Li,3 Yu Zhang,1,2 Na Ding,2 Zhonghua Shen,1,2 Hao Xu,1,2 Xuewu Nian,4 Nan Sha,1,2 Ruifa Han,1,2 Hailong Hu,1,2 Changli Wu1,2 Objective: Human murine double minute 2 protein (MDM2 is mainly a negative regulator of p53 tumor suppressor pathway. We aimed to investigate the association between MDM2 SNP309 polymorphism and bladder cancer risk. Methods: A total of 535 bladder cancer patients and 649 health controls were recruited for our study. MDM2 SNP309 T>G polymorphism was genotyped by polymerase chain reaction-ligase detection reaction method. Logistic regression was used to analyze the relationship between the genotype and susceptibility of bladder cancer. Kaplan–Meier estimates and log-rank test were obtained to analyze the association between the genotype and risk of recrudesce in nonmuscle-invasive bladder cancer patients. A multivariable Cox proportional hazards model was fitted to identify independent prognostic factors. To further investigate the association, we conducted a meta-analysis including six studies. Results: The frequency of the MDM2 SNP309 T>G polymorphism showed no significant difference between cases and controls (all P>0.05. In the stratification analysis, the results showed that G allele carriers were prone to have a significant decrease in risk of low-grade bladder cancer (adjusted odds ratio: 0.613, 95% confidence interval: 0.427–0.881, and G variant was associated with a significantly reduced risk of recurrence in nonmuscle-invasive bladder cancer patients with or without chemotherapy (P<0.05. The results of the meta-analysis showed that G allele and GG genotype of MDM2 SNP309 polymorphism were significantly associated with increased risk of bladder cancer in Caucasians (both P<0.05, and no association was observed in total populations and Asians (P>0.05. Conclusion: MDM2 SNP309 T>G polymorphism has no influence on bladder cancer risk in Asians, but

  13. A study on growth and pyrolysis characteristics of microalgae using Thermogravimetric Analysis-Infrared Spectroscopy and synchrotron Fourier Transform Infrared Spectroscopy.

    Science.gov (United States)

    Li, Fanghua; Srivatsa, Srikanth Chakravartula; Batchelor, Warren; Bhattacharya, Sankar

    2017-04-01

    This two-part study firstly investigated Tetraselmis suecica grown in different CO 2 (0.04-15%v/v) concentration through indoor and outdoor cultivation systems. A high CO 2 concentration led to a high lipid content, and low nitrogen and oxygen content, which are desirable for transport fuel production. Pyrolysis characteristics were investigated by TG-IR and synchrotron IR microscopy. The results show Tetraselmis suecica grown in 10%CO 2 had the highest decomposition rate corresponding to more volatile products produced during the main thermal cracking stage and derived from protein-and lipid-corresponding functional groups. Moreover, a high reaction temperature and CO 2 concentration resulted in a low retention of surface functional groups. The nitrogen functional groups initially decomposed at a temperature range of 250-300°C and still remained at 550°C, while the lipid-corresponding functional groups completely disappeared at a temperature range of 400-500°C. Besides, the decomposition of chemical components followed the order of carbohydrate, protein and lipid. Copyright © 2017 Elsevier Ltd. All rights reserved.

  14. Thyroglobulin (Tg) Testing Revisited: Tg Assays, TgAb Assays, and Correlation of Results With Clinical Outcomes.

    Science.gov (United States)

    Netzel, Brian C; Grebe, Stefan K G; Carranza Leon, B Gisella; Castro, M Regina; Clark, Penelope M; Hoofnagle, Andrew N; Spencer, Carole A; Turcu, Adina F; Algeciras-Schimnich, Alicia

    2015-08-01

    Measurement of thyroglobulin (Tg) by mass spectrometry (Tg-MS) is emerging as a tool for accurate Tg quantification in patients with anti-Tg autoantibodies (TgAbs). The objective of the study was to perform analytical and clinical evaluations of two Tg-MS assays in comparison with immunometric Tg assays (Tg-IAs) and Tg RIAs (Tg-RIAs) in a cohort of thyroid cancer patients. A total of 589 samples from 495 patients, 243 TgAb-/252 TgAb+, were tested by Beckman, Roche, Siemens-Immulite, and Thermo-Brahms Tg and TgAb assays, two Tg-RIAs, and two Tg-MS assays. The frequency of TgAb+ was 58%, 41%, 27%, and 39% for Roche, Beckman, Siemens-Immulite, and Thermo-Brahms, respectively. In TgAb- samples, clinical sensitivities and specificities of 100% and 74%-100%, respectively, were observed across all assays. In TgAb+ samples, all Tg-IAs demonstrated assay-dependent Tg underestimation, ranging from 41% to 86%. In TgAb+ samples, the use of a common cutoff (0.5 ng/mL) for the Tg-MS, three Tg-IAs, and the USC-RIA improved the sensitivity for the Tg-MSs and Tg-RIAs when compared with the Tg-IAs. In up to 20% of TgAb+ cases, Tg-IAs failed to detect Tg that was detectable by Tg-MS. In Tg-RIAs false-high biases were observed in TgAb+ samples containing low Tg concentrations. Tg-IAs remain the method of choice for Tg quantitation in TgAb- patients. In TgAb+ patients with undetectable Tg by immunometric assay, the Tg-MS will detect Tg in up to 20% additional cases. The Tg-RIA will detect Tg in approximately 35% cases, but a significant proportion of these will be clinical false-positive results. The undetectable Tg-MS seen in approximately 40% of TgAb+ cases in patients with disease need further evaluation.

  15. Thermal behavior of biflorin by beans TG and a DSC photovisual system

    Directory of Open Access Journals (Sweden)

    C. F. S. Aragão

    Full Text Available This work proposes thermal characterization, of the biflorine, orto-quinon of Capraria biflora L., through the TG and DSC photovisual data. The thermogravimetric results showed that the decomposition reaction biflorine occurs three steps under air atmosphere, The DSC of biflorin presented five peaks relating to phase transitions. The DSC photovisual system demonstrated changes in biflorin.

  16. Estudo termoanalítico de comprimidos revestidos contendo captopril através de termogravimetria (TG e calorimetria exploratória diferencial (DSC Thermal analysis study of captopril coated tablets by thermogravimetry (TG and differential scanning calorimetry (DSC

    Directory of Open Access Journals (Sweden)

    Giovana Carolina Bazzo

    2005-09-01

    Full Text Available No presente trabalho foram desenvolvidos comprimidos de captopril revestidos com hidroxipropilmetilcelulose (HPMC, Opadry®, polivinilpirrolidona (PVP, Eudragit® E e goma laca. Foi realizado estudo termoanalítico do fármaco e das formulações através de termogravimetria (TG e calorimetria exploratória diferencial (DSC. Através da análise das curvas DSC verificou-se que não houve a ocorrência de interação entre o fármaco e os excipientes lactose, celulose microcristalina, croscarmelose sódica, Aerosil® e talco, utilizados na formulação do comprimido. Através desta técnica detectou-se a possibilidade de interação entre captopril e estearato de magnésio. De acordo com os resultados obtidos através de DSC não foram observadas alterações na cristalinidade do fármaco decorrentes dos processos de compressão e revestimento. A termogravimetria foi utilizada para o estudo da cinética de degradação do captopril e dos comprimidos. Os parâmetros cinéticos foram determinados através do método de Ozawa. Os resultados demonstraram que não houve alteração da estabilidade térmica do captopril na forma de comprimido. A formulação revestida com HPMC foi a que apresentou maior estabilidade térmica, quando comparada às demais formulações de revestimento.In the present study, captopril coated tablets with hydroxypropylmethylcellulose (HPMC, Opadry®, polyvinylpirrolidone (PVP, Eudragit® and shellac were produced. Differential scanning calorimetry (DSC and thermogravimetry (TG were used to evaluate the thermal properties of the drug and the formulations. On the basis of DSC results, captopril was found to be compatible with lactose, microcrystalline cellulose, sodium croscarmellose, Aerosil® and talc. Some possibility of interaction between drug-excipient was observed with magnesium stearate. However, additional techniques to confirm the results obtained are needed. There was no influence of mechanical treatment (tableting

  17. Spectroscopic and thermogravimetric study of nickel sulfaquinoxaline complex

    International Nuclear Information System (INIS)

    Tailor, Sanjay M.; Patel, Urmila H.

    2016-01-01

    The ability of sulfaquinoxaline (4-Amino-N-2-quinoxalinylbenzenesulfonamide) to form metal complexes are investigated. The nickel complex of sulfaquinoxaline is prepared by reflux method and characterized by CHN analysis and IR spectra. The results of IR spectral data suggest that the binding of nickel atom to the sulfonamidic nitrogen are in good agreement. The thermogravimetric analysis (TGA), differential thermal analysis (DTA) and differential thermogravimetric (DTG) analysis of nickel sulfaquinoxaline are carried out from ambient temperature to 750°C in inert nitrogen atmosphere. The activation energy, enthalpy, entropy and Gibbs free energy of nickel sulfaquinoxaline complex is determined from the thermal curves using Broido method. The results are reported in this paper.

  18. A meta-analysis of the antiviral activity of the HBV-specific immunotherapeutic TG1050 confirms its value over a wide range of HBsAg levels in a persistent HBV pre-clinical model.

    Science.gov (United States)

    Kratzer, Roland; Sansas, Benoît; Lélu, Karine; Evlachev, Alexei; Schmitt, Doris; Silvestre, Nathalie; Inchauspé, Geneviève; Martin, Perrine

    2018-02-01

    Pre-clinical models mimicking persistent hepatitis B virus (HBV) expression are seldom, do not capture all features of a human chronic infection and due to their complexity, are subject to variability. We report a meta-analysis of seven experiments performed with TG1050, an HBV-targeted immunotherapeutic, 1 in an HBV-persistent mouse model based on the transduction of mice by an adeno-associated virus coding for an infectious HBV genome (AAV-HBV). To mimic the clinical diversity seen in HBV chronically infected patients, AAV-HBV transduced mice displaying variable HBsAg levels were treated with TG1050. Overall mean percentages of responder mice, displaying decrease in important clinical parameters i.e. HBV-DNA (viremia) and HBsAg levels, were 52% and 51% in TG1050 treated mice, compared with 8% and 22%, respectively, in untreated mice. No significant impact of HBsAg level at baseline on response to TG1050 treatment was found. TG1050-treated mice displayed a significant shorter Time to Response (decline in viral parameters) with an Hazard Ratio (HR) of 8.3 for viremia and 2.6 for serum HBsAg. The mean predicted decrease for TG1050-treated mice was 0.5 log for viremia and 0.8 log for HBsAg, at the end of mice follow-up, compared to no decrease for viremia and 0.3 log HBsAg decrease for untreated mice. For mice receiving TG1050, a higher decline of circulating viremia and serum HBsAg level over time was detected by interaction term meta-analysis with a significant treatment effect (p = 0.002 and pHBV-persistent model mimicking clinical situations.

  19. Diagnostic value of Tg and TgAb for metastasis following ablation in patients with differentiated thyroid carcinoma coexistent with Hashimoto thyroiditis.

    Science.gov (United States)

    Chai, Hong; Zhu, Zhao-Jin; Chen, Ze-Quan; Yu, Yong-Li

    2016-08-01

    This study was designed to investigate the clinical value of serum thyroglobulin (Tg) and antithyroglobulin antibody (TgAb) measurements and the cutoff value after ablation in differentiated thyroid carcinoma (DTC) complicated by Hashimoto thyroiditis (HT) with metastasis. We measured serum Tg and TgAb levels and evaluated the disease status in 164 cases of DTC coexistent with HT in pathologically confirmed patients after surgery and post-remnant ablation during a 3-year follow-up. All Tg and TgAb levels were assessed by chemiluminescent immunoassay (IMA). Receiver operating characteristic (ROC) curve analysis was used to evaluate the prognostic value of Tg and TgAb for disease metastasis. The relationship between Tg and TgAb was analyzed using the scatter diagram distribution method. We found that the cutoff values of Tg and TgAb were 1.48 µg/L and 45 kIU/L, respectively. The area under the ROC curve (AUC) of Tg and TgAb was 0.907 and 0.650, respectively. In DTC coexistent with HT patients, the optimal cutoff value correlated with metastasis in Tg and TgAb was 1.48 µg/L and 45 kIU/L, respectively.

  20. Spectroscopic, thermogravimetric and structural characterization analyses for comparing Municipal Solid Waste composts and vermicomposts stability and maturity.

    Science.gov (United States)

    Soobhany, Nuhaa; Gunasee, Sanjana; Rago, Yogeshwari Pooja; Joyram, Hashita; Raghoo, Pravesh; Mohee, Romeela; Garg, Vinod Kumar

    2017-07-01

    This is the first-ever study of its kind for an extensive assessment and comparison of maturity indexes between compost and vermicompost that have been derived from Municipal Solid Waste (MSW). The spectroscopic (Fourier transform infrared spectroscopy: FT-IR), thermogravimetric analysis (TG), differential scanning calorimetry (DSC) and structural characterization (scanning electron microscope: SEM) were recorded. FT-IR spectra showed an increase in conversion of polysaccharides species and aliphatic methylene groups in vermicompost compared to compost as depicted from the variation of the intensity of the peaks. TG curves of final vermicompost showed a much lower mass loss when compared to compost, indicating higher stability in feedstock. SEM micrographs of the vermicompost reflected strong fragmentation of material than composts which revealed the extent of intra-structural degradation of MSW. These findings elucidate on a clear comparison between composts and vermicomposts in terms of maturity indexes for soil enhancement and in agriculture as organic fertilizer. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. Synthesis, thermogravimetric, spectroscopic and theoretical characterization of copper(II) complex with 4-chloro-2-nitrobenzenosulfonamide

    Science.gov (United States)

    Camí, G.; Chacón Villalba, E.; Di Santi, Y.; Colinas, P.; Estiu, G.; Soria, D. B.

    2011-05-01

    4-Chloro-2-nitrobenzenesulfonamide (ClNbsa) was purified and characterized. A new copper(II) complex, [Cu(ClNbsa) 2(NH 3) 2], has been prepared using the sulfonamide as ligand. The thermal behavior of both, the ligand and the Cu(II) complex, was investigated by thermogravimetric analyses (TG) and differential thermal analysis (DT), and the electronic characteristics analyzed by UV-VIS, FTIR, Raman and 1H NMR spectroscopies. The experimental IR, Raman and UV-VIS spectra have been assigned on the basis of DFT calculations at the B3LYP level of theory using the standard (6-31 + G ∗∗) basis set. The geometries have been fully optimized in vacuum and in modeled dimethylsulfoxide (DMSO) solvent, using for the latter a continuum solvation model that reproduced the experimental conditions of the UV-VIS spectroscopy. The theoretical results converged to stable conformations for the free sulfonamide and for the complex, suggesting for the latter a distorted square planar geometry in both environments.

  2. Lithium-ion battery electrolyte emissions analyzed by coupled thermogravimetric/Fourier-transform infrared spectroscopy

    Science.gov (United States)

    Bertilsson, Simon; Larsson, Fredrik; Furlani, Maurizio; Albinsson, Ingvar; Mellander, Bengt-Erik

    2017-10-01

    In the last few years the use of Li-ion batteries has increased rapidly, powering small as well as large applications, from electronic devices to power storage facilities. The Li-ion battery has, however, several safety issues regarding occasional overheating and subsequent thermal runaway. During such episodes, gas emissions from the electrolyte are of special concern because of their toxicity, flammability and the risk for gas explosion. In this work, the emissions from heated typical electrolyte components as well as from commonly used electrolytes are characterized using FT-IR spectroscopy and FT-IR coupled with thermogravimetric (TG) analysis, when heating up to 650 °C. The study includes the solvents EC, PC, DEC, DMC and EA in various single, binary and ternary mixtures with and without the LiPF6 salt, a commercially available electrolyte, (LP71), containing EC, DEC, DMC and LiPF6 as well as extracted electrolyte from a commercial 6.8 Ah Li-ion cell. Upon thermal heating, emissions of organic compounds and of the toxic decomposition products hydrogen fluoride (HF) and phosphoryl fluoride (POF3) were detected. The electrolyte and its components have also been extensively analyzed by means of infrared spectroscopy for identification purposes.

  3. Pyrolysis of olive residue/low density polyethylene mixture:Part I Thermogravimetric kinetics

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    This paper demonstrates the thermal pyrolysis of olive residue, low density polyethylene (LDPE) and olive residue/LDPE mixture in an inert atmosphere of N2 using thermogravimetric analysis (TGA). Measurements were carried out in the temperature range 300K~973K at heating rates of 2K/min, 10K/min, 20K/min and 50K/min. Based on the results obtained, three temperature regimes were selected for studying the non-isothermal kinetics of olive residue/LDPE mixture. The first two were dominated by the olive residue pyrolysis, while the third was linked to the LDPE pyrolysis, which occurred at much higher temperatures. Discrepancies between the experimental and calculated TG/DTG profiles were considered as a measurement of the extent of interactions occurring on co-pyrolysis. The maximum degradation temperatures of each component in the mixture were higher than those the individual components;thus an increase in thermal stability was expected. The kinetic parameters associated with thermal degradation were determined using Friedman isoconversional method.

  4. Thyroglobulin (Tg) recovery testing with quantitative Tg antibody measurement for determining interference in serum Tg assays in differentiated thyroid carcinoma

    NARCIS (Netherlands)

    Persoon, ACM; Links, TP; Wilde, J; Sluiter, WJ; Wolffenbuttel, BHR; van den Ouweland, JMW

    Background: Thyroglobulin (Tg) measurements are complicated by interference from Tg autoantibodies (TgAbs) or heterophilic antibodies (HAMAs). We used a new automated immunochemiluminometric assay (ICMA) with Tg recovery (TgR) on the Nichols Advantage (R) platform to reassess the clinical utility of

  5. Assessment of a new method for the analysis of decomposition gases of polymers by a combining thermogravimetric solid-phase extraction and thermal desorption gas chromatography mass spectrometry.

    Science.gov (United States)

    Duemichen, E; Braun, U; Senz, R; Fabian, G; Sturm, H

    2014-08-08

    For analysis of the gaseous thermal decomposition products of polymers, the common techniques are thermogravimetry, combined with Fourier transformed infrared spectroscopy (TGA-FTIR) and mass spectrometry (TGA-MS). These methods offer a simple approach to the decomposition mechanism, especially for small decomposition molecules. Complex spectra of gaseous mixtures are very often hard to identify because of overlapping signals. In this paper a new method is described to adsorb the decomposition products during controlled conditions in TGA on solid-phase extraction (SPE) material: twisters. Subsequently the twisters were analysed with thermal desorption gas chromatography mass spectrometry (TDS-GC-MS), which allows the decomposition products to be separated and identified using an MS library. The thermoplastics polyamide 66 (PA 66) and polybutylene terephthalate (PBT) were used as example polymers. The influence of the sample mass and of the purge gas flow during the decomposition process was investigated in TGA. The advantages and limitations of the method were presented in comparison to the common analysis techniques, TGA-FTIR and TGA-MS. Copyright © 2014 Elsevier B.V. All rights reserved.

  6. An in situ FTIR spectroscopic and thermogravimetric analysis study of the dehydration and dihydroxylation of SnO2: the contribution of the (100), (110) and (111) facets.

    Science.gov (United States)

    Christensen, P A; Attidekou, P S; Egdell, R G; Maneelok, S; Manning, D A C

    2016-08-17

    Nanoparticulate SnO2 produced by a hydrothermal method was characterised by BET, XRD, TGA-MS and in situ variable temperature diffuse reflectance infra red spectroscopy (DRIFTS) to determine the surface behaviour of water. For the (100) facets, hydrogen bonding does not occur, and water adsorption is less strong than for the (111) and (110) facets where hydrogen bonding does occur. Reversible uptake of oxygen was observed. These findings have implications for other surface-gas reactions in which Ni and Sb co-doped SnO2 (NATO) anodes are used for ozone generation. BET showed the relatively high surface area and nanometer scale of the SnO2 particles, whilst XRD confirmed the nano dimension of the crystallites and showed only the cassiterite phase. TGA analysis indicated four temperature regions over which mass loss was observed. These and the in situ DRIFTS studies revealed the existence of various forms of water associated with specific crystal facets of the SnO2, as well as the existence of isolated O-H groups and adsorbed oxygen species. Electronic absorptions were also observed and the data rationalised in terms of the existence of both free electron absorptions, and absorptions from oxygen vacancy states. The role of adsorbed molecular oxygen in electrochemical ozone generation at Ni and Sb co-doped SnO2 (NATO) anodes was strongly suggested by this work.

  7. Study of solid chemical evolution in torrefaction of different biomasses through solid-state "1"3C cross-polarization/magic angle spinning NMR (nuclear magnetic resonance) and TGA (thermogravimetric analysis)

    International Nuclear Information System (INIS)

    Rodriguez Alonso, Elvira; Dupont, Capucine; Heux, Laurent; Da Silva Perez, Denilson; Commandre, Jean-Michel; Gourdon, Christophe

    2016-01-01

    The objective of this work is to compare mass loss and chemical evolution of the solid phase, versus time, during dynamic torrefaction of different types of biomass. For this purpose, two experiments, ThermoGravimetric Analysis and solid-state "1"3C Cross-Polarization/Magic Angle Spinning Nuclear Magnetic Resonance, were run on four representative biomasses. Overall mass loss and chemical evolution of the solid phase were followed, respectively, as a function of temperature and time. Thanks to this coupled information, it was shown that the knowledge of both solid mass loss and chemical evolution is necessary to characterize torrefaction severity. Moreover, biomasses containing higher proportions of xylan lost mass faster than those containing lower proportions. Lignin showed a protecting role towards cellulose, which would lead to a faster degradation of non-woody biomasses in comparison with woody biomasses. Three parameters would have an influence on solid chemical evolution during torrefaction: xylan content in hemicellulose, lignin content in biomass, and cellulose crystallinity. - Highlights: • Torrefaction of four biomasses was studied with TGA and solid-state NMR. • Both solid mass loss and chemical evolution characterize torrefaction severity. • Biomasses containing a higher proportion of xylan lose mass faster. • Lignin shows a stronger protecting role in degradation of woody biomasses. • Xylan, lignin and crystalline cellulose values influence solid chemical evolution.

  8. Molecular docking, TG/DTA, molecular structure, harmonic vibrational frequencies, natural bond orbital and TD-DFT analysis of diphenyl carbonate by DFT approach

    Science.gov (United States)

    Xavier, S.; Periandy, S.; Carthigayan, K.; Sebastian, S.

    2016-12-01

    Vibrational spectral analysis of Diphenyl Carbonate (DPC) is carried out by using FT-IR and FT-Raman spectroscopic techniques. It is found that all vibrational modes are in the expected region. Gaussian computational calculations were performed using B3LYP method with 6-311++G (d, p) basis set. The computed geometric parameters are in good agreement with XRD data. The observation shows that the structure of the carbonate group is unsymmetrical by ∼5° due to the attachment of the two phenyl rings. The stability of the molecule arising from hyperconjugative interaction and charge delocalization are analyzed by Natural Bond Orbital (NBO) study and the results show the lone pair transition has higher stabilization energy compared to all other. The 1H and 13C NMR chemical shifts are calculated using the Gauge-Including Atomic Orbital (GIAO) method with B3LYP/6-311++G (d, p) method. The chemical shifts computed theoretically go very closer to the experimental results. A study on the electronic and optical properties; absorption wavelengths, excitation energy, dipole moment and frontier molecular orbital energies and Molecular electrostatic potential (MEP) exhibit the high reactivity nature of the molecule. The non-linear optical property of the DPC molecule predicted theoretically found to be good candidate for NLO material. TG/DTA analysis was made and decomposition of the molecule with respect to the temperature was studied. DPC having the anthelmintic activity is docked in the Hemoglobin of Fasciola hepatica protein. The DPC has been screened to antimicrobial activity and found to exhibit antibacterial effects.

  9. Thermogravimetric assessment of thermal degradation in asphaltenes

    Energy Technology Data Exchange (ETDEWEB)

    Barneto, Agustín García, E-mail: agustin.garcia@diq.uhu.es [Department of Chemical Engineering, Physical Chemistry and Organic Chemistry, University of Huelva, Huelva (Spain); Carmona, José Ariza [Department of Chemical Engineering, Physical Chemistry and Organic Chemistry, University of Huelva, Huelva (Spain); Garrido, María José Franco [CEPSA, RDI Centre, Madrid (Spain)

    2016-03-20

    Graphical abstract: - Highlights: • Asphaltenes content of visbreaking streams in oil refinery can be measured by using TGA. • Deconvoluting TGA curves allows the thermal-based composition of asphaltenes to be elucidated. • Asphaltenes cracking involves acceleratory stages compatible with autocatalytic kinetic. • Activation energy during asphaltenes pyrolysis increased with increasing temperature. • Activation energy remained almost constant at 200–225 kJ/mol during oxidative cracking. - Abstract: Monitoring asphaltenes is very important with a view to optimizing visbreaking units in oil refineries. Current analyses based on selective dissolution in different solvents are slow, so new, more expeditious methods for measuring asphaltenes are required to facilitate fuel-oil production. In this work, we studied the thermal degradation of asphaltenes as the potential basis for a thermogravimetric method for their monitoring in visbreaking streams. The thermal degradation of asphaltenes occurs largely from 400 to 500 °C; the process is quite smooth in an inert environment but involves several fast mass loss events in the air. Kinetic parameters for characterizing the process were determined by using two model-free methods and the modified Prout–Tompkins kinetic equation to examine asphaltene thermolysis. Both types of methods showed the activation energy to increase during pyrolysis but to remain almost constant during cracking in the presence of oxygen or even diminish during char oxidation. Deconvoluting the thermogravimetric profiles revealed that asphaltene thermolysis in the air cannot be accurately described in terms of an nth order kinetic model because it involves some acceleratory phases. Also, thermogravimetric analyses of visbreaking streams revealed that char production in them is proportional to their asphaltene content. This relationship enables the thermogravimetric measurement of asphaltenes.

  10. Thermogravimetric assessment of thermal degradation in asphaltenes

    International Nuclear Information System (INIS)

    Barneto, Agustín García; Carmona, José Ariza; Garrido, María José Franco

    2016-01-01

    Graphical abstract: - Highlights: • Asphaltenes content of visbreaking streams in oil refinery can be measured by using TGA. • Deconvoluting TGA curves allows the thermal-based composition of asphaltenes to be elucidated. • Asphaltenes cracking involves acceleratory stages compatible with autocatalytic kinetic. • Activation energy during asphaltenes pyrolysis increased with increasing temperature. • Activation energy remained almost constant at 200–225 kJ/mol during oxidative cracking. - Abstract: Monitoring asphaltenes is very important with a view to optimizing visbreaking units in oil refineries. Current analyses based on selective dissolution in different solvents are slow, so new, more expeditious methods for measuring asphaltenes are required to facilitate fuel-oil production. In this work, we studied the thermal degradation of asphaltenes as the potential basis for a thermogravimetric method for their monitoring in visbreaking streams. The thermal degradation of asphaltenes occurs largely from 400 to 500 °C; the process is quite smooth in an inert environment but involves several fast mass loss events in the air. Kinetic parameters for characterizing the process were determined by using two model-free methods and the modified Prout–Tompkins kinetic equation to examine asphaltene thermolysis. Both types of methods showed the activation energy to increase during pyrolysis but to remain almost constant during cracking in the presence of oxygen or even diminish during char oxidation. Deconvoluting the thermogravimetric profiles revealed that asphaltene thermolysis in the air cannot be accurately described in terms of an nth order kinetic model because it involves some acceleratory phases. Also, thermogravimetric analyses of visbreaking streams revealed that char production in them is proportional to their asphaltene content. This relationship enables the thermogravimetric measurement of asphaltenes.

  11. Thermogravimetric analysis of combustible waste components

    DEFF Research Database (Denmark)

    Munther, Anette; Wu, Hao; Glarborg, Peter

    In order to gain fundamental knowledge about the co-combustion of coal and waste derived fuels, the pyrolytic behaviors of coal, four typical waste components and their mixtures have been studied by a simultaneous thermal analyzer (STA). The investigated waste components were wood, paper, polypro......In order to gain fundamental knowledge about the co-combustion of coal and waste derived fuels, the pyrolytic behaviors of coal, four typical waste components and their mixtures have been studied by a simultaneous thermal analyzer (STA). The investigated waste components were wood, paper...

  12. A Combined Variable-Temperature Neutron Diffraction and Thermogravimetric Analysis Study on a Promising Oxygen Electrode, SrCo0.9Nb0.1O3-δ, for Reversible Solid Oxide Fuel Cells.

    Science.gov (United States)

    Yang, Tianrang; Wang, Jie; Chen, Yan; An, Ke; Ma, Dong; Vogt, Thomas; Huang, Kevin

    2017-10-11

    The present study investigates the temperature-structure-stoichiometry relationship of a promising oxygen electrode SrCo 0.9 Nb 0.1 O 3-δ over a temperature (T) range from room temperature (RT) to 900 °C. The techniques employed are variable-temperature neutron diffraction (VTND) and thermogravimetric analysis (TGA). At T < 75 °C, VTND reveals a tetragonal (P4/mmm) structure with a G-type magnetic ordering. Above 75 °C, the nucleus structure remains the same, while the magnetic ordering disappears. A phase transition from tetragonal (P4/mmm) to cubic (Pm3̅m) is observed at 412 °C, where the two Co sites and three O sites in the P4/mmm phase converge to one equivalent site, respectively. The phase transition temperature coincides with the peak temperature of oxygen uptake obtained by TGA. It is also observed that the Nb dopant has no preferred Co site to occupy. The oxygen vacancies are mostly located at the O3 site surrounding the Co2 site in the P4/mmm structure. The intermediate-spin state of Co 3+ at the Co2 site is responsible for the observed distortions of CoO 6 octahedra, i.e., elongation of Co2O 6 octahedra and shortening of Co1O 6 octahedra along the c-axis, which is a phenomenon known as Jahn-Teller distortion. At high temperatures, large thermal displacement factor for O 2- is observed with high concentration of oxygen vacancies, providing a structural environment favorable to high O 2- conductivity in Nb-doped SrCoO 3 -based oxygen electrode materials.

  13. Surface area and pore size characteristics of nanoporous gold subjected to thermal, mechanical, or surface modification studied using gas adsorption isotherms, cyclic voltammetry, thermogravimetric analysis, and scanning electron microscopy

    Science.gov (United States)

    Tan, Yih Horng; Davis, Jason A.; Fujikawa, Kohki; Ganesh, N. Vijaya; Demchenko, Alexei V.

    2012-01-01

    Nitrogen adsorption/desorption isotherms are used to investigate the Brunauer, Emmett, and Teller (BET) surface area and Barrett-Joyner-Halenda (BJH) pore size distribution of physically modified, thermally annealed, and octadecanethiol functionalized np-Au monoliths. We present the full adsorption-desorption isotherms for N2 gas on np-Au, and observe type IV isotherms and type H1 hysteresis loops. The evolution of the np-Au under various thermal annealing treatments was examined using scanning electron microscopy (SEM). The images of both the exterior and interior of the thermally annealed np-Au show that the porosity of all free standing np-Au structures decreases as the heat treatment temperature increases. The modification of the np-Au surface with a self-assembled monolayer (SAM) of C18-SH (coverage of 2.94 × 1014 molecules cm−2 based from the decomposition of the C18-SH using thermogravimetric analysis (TGA)), was found to reduce the strength of the interaction of nitrogen gas with the np-Au surface, as reflected by a decrease in the ‘C’ parameter of the BET equation. From cyclic voltammetry studies, we found that the surface area of the np-Au monoliths annealed at elevated temperatures followed the same trend with annealing temperature as found in the BET surface area study and SEM morphology characterization. The study highlights the ability to control free-standing nanoporous gold monoliths with high surface area, and well-defined, tunable pore morphology. PMID:22822294

  14. Miniature quartz crystal-resonator-based thermogravimetric detector.

    Science.gov (United States)

    Sai, N; Tagawa, Y; Sohgawa, M; Abe, T

    2014-09-01

    In this work, a new design for a microheater combined with a quartz crystal microbalance (QCM) array for thermogravimetric analysis is presented. Each QCM consists of two electrodes to excite thickness-shear-mode vibrations and one microheater to increase the temperature on the crystal backside. In addition, all the electrode pads are patterned on the crystal backside, making the design of the QCM compact and user-friendly. Finally, the proposed QCM array was employed to separate ethanol from methanol. This was successfully achieved via thermal desorption spectra calculated by differentiating the frequency changes.

  15. Análise termogravimétrica do óleo essencial de pimenta longa (Piper hispidinervium C. DC Thermogravimetric analysis of long pepper (Piper hispidinervium C.DC. essential oil

    Directory of Open Access Journals (Sweden)

    Marco Aurelio Cremasco

    2011-01-01

    Full Text Available A pimenta longa (Piper hispidinervium C. DC. é um arbusto originário da região amazônica, cujo óleo essencial é rico em safrol. O óleo essencial da pimenta longa é comercializado in natura, o que faz o processamento para a obtenção do safrol elemento fundamental de investigação científica e tecnológica. Uma importante etapa para a obtenção do safrol é a definição da estratégia da sua separação do óleo essencial a partir, por exemplo, da destilação. Neste caso, torna-se essencial o conhecimento de parâmetros termodinâmicos, tais como energia de ativação e calor latente de vaporização. Neste trabalho é utilizada a técnica termogravimétrica para a obtenção dos valores da energia de ativação e calor latente de vaporização do óleo essencial de P. hispidinervium. O processo de evaporação do óleo essencial obedece à cinética de ordem zero, resultando para a energia de ativação e calor latente de vaporização os valores 42,11 kJ.mol-1 e 43,73 kJ.mol-1, respectivamente.Long pepper (Piper hispidinervium C. DC. is a shrub found in the Amazon region, which supplies an essential oil rich in safrole. Normally, long pepper essential oil is commercialized in natura, which makes its processing a fundamental step in scientific and technological investigation. An important step of safrole commercialization is the separation of essential oil by, for example, a distillation process. In such a case it is important to know some thermodynamics parameters, such as energy of activation and enthalpy of vaporization. The present study was aimed at applying the kinetic of zero order evaporation process for the essential oil of P. hispidinervum by thermogravimetric analysis. The thermal analysis data were utilized to determine the energy of activation and enthalpy of vaporization, which resulted in the values 41.11 kJ.mol-1 and 43.73 kJ.mol-1, respectively.

  16. Thermogravimetric research of hydrogen storage materials

    International Nuclear Information System (INIS)

    Kleperis, J; Grinberga, L; Ergle, M; Chikvaidze, G; Klavins, J

    2007-01-01

    During thermogravimetric research of metal hydrides we noticed mass growth of samples above 200 deg. C even in an argon atmosphere. Further heating is leading to the growth of weight up to 2-7 weight% till 500 0 C. Second run of the same sample without taking out of DTA instrument gave only small mass changes, indicating that noticed mass increase during first run is permanent. Microscope and elemental analyses were made to determine the reason of mass growth. XRD inspection revealed the formation of new phase with bunsenite NiO structure with deformed cubic structure. The new phase is no more active to hydrogen sorption/desorption. Our results demonstrated that the usage of hydrogen storage alloys AB 5 must be taken with care - it is important not to exceed some critical temperature were irreversible structural, compositional and morphological changes will occur

  17. THERMOGRAVIMETRIC INVESTIGATIONS OF VAGINAL SUPPOSITORY WITH THYME OIL

    Directory of Open Access Journals (Sweden)

    N. V. Melnikova

    2015-04-01

    Full Text Available One of the main stages in new medicines creation is the development of their making technology. Technological process of suppository making includes ratherlongthermal treatment during preparation and homogenization of suppository base, active substancesaddition. These factors create danger of chemical and physical transformation of active substances and excipients in suppository up to their destruction and change of pharmacological and physical-chemical properties. Use of thermogravimetric analysis in pharmaceutical technology allows to studythepossibility of chemical interaction in dosage forms over the wide temperature range. The aim of this work is study of thermal treatmenteffects of suppository base with thyme oil over the temperature range of suppository manufacturing. Methods and results. As an object of thermogravimetric study vaginal suppository with thyme oil 0,2 g, suppository-placebo containing propylenglycol, polyethylene glycol 400, proxanol 268, twin 80 and the active ingredient of «Царствоароматов», Ukraine, production were used. Thermogravimetric analysis was carried out on the derivatograph«Shimadzu DTG-60», Japan, with the platinum and platinum-rhodiumthermopair with samples heating in aluminiumcrucibles from 25 to 200ºС. As standard α-Al2O3was used.Heating rate was 10ºСper min.Mass of the samples was 23,45– 39,63 mg. Obtained data were registered by the derivatograph as curves T, DTA, TGA. The T curve on the derivatogramm shows the temperature change and the TGA curve demonstrates the sample mass change during investigation. The DTA curve reflects differentiation of thermal effects and contains information about endothermic and exothermal maximum and is used for qualitative valuation of derivatogramm. According to results of thermogravimetric investigation the thyme oil is thermostable substance which is gradually evaporating during heating. So, at the beginning of study the test sample mass was 23

  18. A comparative Tg-Ms study of the carbonization behaviour of different pitches

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, R.; Arenillas, A.; Crespo, J.L.; Pis, J.J.; Moinelo, S.R. [CSIC, Oviedo (Spain). Inst. Nacional del Carbon

    2002-08-01

    The purpose of this work was to study the formation of mesophase spherules from a low-temperature coal tar pitch under carbonization conditions. For comparison, the carbonization of a high-temperature coal tar pitch and a petroleum pitch were also considered. Different degrees of mesophase formation and development for each pitch. The results from Fourier transform infrared spectroscopy (FT-IR), elemental analysis, and the thermogravimetric analyzer mass spectrometer (TG-MS) tests were compared with the different extents of mesophase formation, checked by optical microscopy. According to the results, several stages can be distinguished as temperature increases in the carbonization process of the pitches. In the low-temperature coal tar pitch, the devolatilization of light components, especially phenols, accounts for the most significant weight loss. Moreover, cross-linking contributes greatly to the formation and development of mesophase, resulting in the predominance of bulk mesophase in a relatively short time in the case of the low-temperature coal tar pitch. 19 refs., 10 figs., 2 tabs.

  19. Catalytic thermal decomposition of polyethylene determined by thermogravimetric treatment

    International Nuclear Information System (INIS)

    Nisar, J.; Khan, M.S.; Khan, M.A.

    2014-01-01

    In this study low density polyethylene (LDPE) has been studied by thermogravimetric analysis (TGA) using commercially available oxides as catalysts. TGA experiments were used to evaluate the activity of different catalysts on low density polyethylene (LDPE) degradation and to study the effect in terms of type and amount of catalyst used. All the catalysts used improved the pyrolysis of LDPE. The reaction rates were found to increase with increase in amount of catalyst. Among the catalysts used, alumina acidic active catalyst performed better at all four fractions. Moreover, alumina acidic active reduced weight loss temperature better than others tested catalysts. The effect of alumina neutral catalyst on the pyrolysis of LDPE is less pronounced due to its small surface area and pore size. The effect of these catalysts showed that surface area, number of acidic sites and pore size were found as the key factors for the energy efficient degradation of polymers. (author)

  20. TU-B-304-00: The Aftermath of TG-142

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2015-06-15

    Although published in 2009, the AAPM TG-142 report on accelerator quality assurance still proves a challenge for full clinical implementation. The choice of methodologies to satisfy TG-142 requirements is critical to a successful application. Understanding the philosophy of TG-142 can help in creating an institution-specific QA practice that is both efficient and effective. The concept of maintaining commissioned beam profiles is still found confusing. The physicist must also consider technologies not covered by TG-142 (i.e. arc therapy techniques). On the horizon is TG-198 report on implementing TG-142. Although the community still lacks a final TG-100 report, performing a failure-mode -and-effects analysis and statistical process control analysis to determine the institution-specific clinical impact of each TG-142 test may be useful for identifying trends for pro-active surveillance. Learning Objectives: To better understand the confusing and controversial aspects of TG-142. To understand what is still missing from TG-142 and how to account for these tests in clinical practice To describe which QA tests in TG-142 yield the largest potential clinical result if not discovered.

  1. TU-B-304-01: The Aftermath of TG-142

    Energy Technology Data Exchange (ETDEWEB)

    Klein, E. [Washington University (United States)

    2015-06-15

    Although published in 2009, the AAPM TG-142 report on accelerator quality assurance still proves a challenge for full clinical implementation. The choice of methodologies to satisfy TG-142 requirements is critical to a successful application. Understanding the philosophy of TG-142 can help in creating an institution-specific QA practice that is both efficient and effective. The concept of maintaining commissioned beam profiles is still found confusing. The physicist must also consider technologies not covered by TG-142 (i.e. arc therapy techniques). On the horizon is TG-198 report on implementing TG-142. Although the community still lacks a final TG-100 report, performing a failure-mode -and-effects analysis and statistical process control analysis to determine the institution-specific clinical impact of each TG-142 test may be useful for identifying trends for pro-active surveillance. Learning Objectives: To better understand the confusing and controversial aspects of TG-142. To understand what is still missing from TG-142 and how to account for these tests in clinical practice To describe which QA tests in TG-142 yield the largest potential clinical result if not discovered.

  2. TU-B-304-02: Quantitative FMEA of TG-142

    Energy Technology Data Exchange (ETDEWEB)

    O’Daniel, J. [Duke University Medical Center (United States)

    2015-06-15

    Although published in 2009, the AAPM TG-142 report on accelerator quality assurance still proves a challenge for full clinical implementation. The choice of methodologies to satisfy TG-142 requirements is critical to a successful application. Understanding the philosophy of TG-142 can help in creating an institution-specific QA practice that is both efficient and effective. The concept of maintaining commissioned beam profiles is still found confusing. The physicist must also consider technologies not covered by TG-142 (i.e. arc therapy techniques). On the horizon is TG-198 report on implementing TG-142. Although the community still lacks a final TG-100 report, performing a failure-mode -and-effects analysis and statistical process control analysis to determine the institution-specific clinical impact of each TG-142 test may be useful for identifying trends for pro-active surveillance. Learning Objectives: To better understand the confusing and controversial aspects of TG-142. To understand what is still missing from TG-142 and how to account for these tests in clinical practice To describe which QA tests in TG-142 yield the largest potential clinical result if not discovered.

  3. Thermogravimetric characteristics of typical municipal solid waste fractions during co-pyrolysis.

    Science.gov (United States)

    Zhou, Hui; Long, YanQiu; Meng, AiHong; Li, QingHai; Zhang, YanGuo

    2015-04-01

    The interactions of nine typical municipal solid waste (MSW) fractions during pyrolysis were investigated using the thermogravimetric analyzer (TGA). To compare the mixture results with the calculation results of superposition of single fractions quantitatively, TG overlap ratio was introduced. There were strong interactions between orange peel and rice (overlap ratio 0.9736), and rice and poplar wood (overlap ratio 0.9774). The interactions of mixture experiments postponed the peak and lowered the peak value. Intense interactions between PVC and rice, poplar wood, tissue paper, wool, terylene, and rubber powder during co-pyrolysis were observed, and the pyrolysis at low temperature was usually promoted. The residue yield was increased when PVC was blended with rice, poplar wood, tissue paper, or rubber powder; while the residue yield was decreased when PVC was blended with wool. Copyright © 2014 Elsevier Ltd. All rights reserved.

  4. Thermogravimetric and x-ray diffraction analyses of Luna-24 regolith samples

    International Nuclear Information System (INIS)

    Deshpande, V.V.; Dharwadkar, S.R.; Jakkal, V.S.

    1979-01-01

    Two samples of Luna-24 were analysed by X-ray diffraction and thermogravimetric (TG) techniques. The sample 24123.12 shows a weight loss of nearly 0.85 percent between 23O-440deg C and followed by 1.16 percent weight gain from 500 to 800deg C. The sample 23190.13 showed only a weight gain of about 1.5 percent from 5O0deg C to 900deg C. X-ray diffraction analyses show the presence of olivine, plagioclase, pigeonite, enstatite, and native iron in both the virgin samples. The heated samples, however, show that only the native iron got oxidized to iron oxide. The other constituents remain unaltered. (auth.)

  5. Pb-H2O Thermogravimetric Plants. The Rankine Cycle

    International Nuclear Information System (INIS)

    Arosio, S.; Carlevaro, R.

    2000-01-01

    An economic evaluation concerning Pb-H 2 O thermogravimetric systems with an electric power in the range 200-1.000 kW has been done. Moreover, plant and running costs for a thermogravimetric and a Rankine cycle, 1 MW power, have been compared. Basically due to the lead charge, the plant cost of the former is higher: nevertheless such amount can be recuperated in less than three years, being higher the running cost of the latter [it

  6. Kinetics of Pyrolysis and Gasification Using Thermogravimetric and Thermovolumetric Analyses

    Directory of Open Access Journals (Sweden)

    Czerski Grzegorz

    2016-03-01

    Full Text Available The carbon dioxide gasification process of Miscanthus giganteus biomass was examined using two methods. First an isothermal thermovolumetric method was applied. The measurement was conducted at 950°C and pressure of 0.1 MPa. Based on the continuous analysis of different kinds of gases formed during the gasification process, the thermovolumetric method allowed the determination of yields and composition of the resulting gas as well as the rate constant of CO formation. Then a non-isothermal thermogravimetric method was applied, during which the loss of weight of a sample as a function of temperature was recorded. In the course of the measurement, the temperature was raised from ambient to 950°C and the pressure was 0.1 MPa. As a result, a change in the carbon conversion degree was obtained. Moreover, TGA methods allow distinguishing various stages of the gasification process such as primary pyrolysis, secondary pyrolysis and gasification, and determining kinetic parameters for each stage. The presented methods differs from each other as they are based either on the analysis of changes in the resulting product or on the analysis of changes in the supplied feedstock, but both can be successfully used to the effective examination of kinetics of the gasification process. In addition, an important advantage of both methods is the possibility to carry out the gasification process for different solid fuels as coal, biomass, or solid waste in the atmosphere of a variety of gasification agents.

  7. Preparation and thermogravimetric study of some uranyl phosphates

    International Nuclear Information System (INIS)

    Schaekers, J.M.

    1970-10-01

    The preparation of uranyl ammonium phosphate trihydrate (UAP = UO 2 NH 4 PO 4 .3H 2 O), acid uranyl phosphate tetrahydrate(AUP = UO 2 HPO 4 .4H 2 O) and neutral uranyl phosphate tetrahydrate (NUPT = (UO 2 ) 3 (PO 4 ) 2 .4H 2 O) was investigated during the data from the literature. The thermal decomposition in different atmospheres, such as air, oxygen, nitrogen and argon, was studied in the temperature range 25-1000 0 C. It was found that the pyrophosphate U 2 O 3 P 2 O 7 is a stable decomposition product of UAP as well as of AUP. A mixture of U 3 O 8 and U 2 O 3 P 2 O 7 is obtained when the NUPT is decomposed in an oxygen-free atmosphere. NUPT however is stable in an oxidising atmosphere. Hydrogen and carbon reductions were also carried out, and UO 2 or (UO) 2 P 2 O 7 as well as mixtures of these two products can be obtained, depending on the starting material and the reduction temperature. The different reduction and decomposition reactions were studied by means of thermogravimetric analysis, and activation energies were calculated where possible. I.R. spectral analysis was also used to identify various products with the same composition [af

  8. Pyrolysis characteristics and kinetics of aquatic biomass using thermogravimetric analyzer.

    Science.gov (United States)

    Wu, Kejing; Liu, Ji; Wu, Yulong; Chen, Yu; Li, Qinghai; Xiao, Xin; Yang, Mingde

    2014-07-01

    The differences in pyrolysis process of three species of aquatic biomass (microalgae, macroalgae and duckweed) were investigated by thermogravimetric analysis (TGA). Three stages were observed during the pyrolysis process and the main decomposition stage could be divided further into three zones. The pyrolysis characteristics of various biomasses were different at each zone, which could be attributed to the differences in their components. A stepwise procedure based on iso-conversional and master-plots methods was used for the kinetic and mechanism analysis of the main decomposition stage. The calculation results based on the kinetic model was in good agreement with the experimental data of weight loss, and each biomass had an increasing activation energy of 118.35-156.13 kJ/mol, 171.85-186.46 kJ/mol and 258.51-268.71 kJ/mol in zone 1, 2 and 3, respectively. This study compares the pyrolysis behavior of various aquatic biomasses and provides basis for further applications of the biomass thermochemical conversion. Copyright © 2014. Published by Elsevier Ltd.

  9. Method for Determining the Activation Energy Distribution Function of Complex Reactions by Sieving and Thermogravimetric Measurements.

    Science.gov (United States)

    Bufalo, Gennaro; Ambrosone, Luigi

    2016-01-14

    A method for studying the kinetics of thermal degradation of complex compounds is suggested. Although the method is applicable to any matrix whose grain size can be measured, herein we focus our investigation on thermogravimetric analysis, under a nitrogen atmosphere, of ground soft wheat and ground maize. The thermogravimetric curves reveal that there are two well-distinct jumps of mass loss. They correspond to volatilization, which is in the temperature range 298-433 K, and decomposition regions go from 450 to 1073 K. Thermal degradation is schematized as a reaction in the solid state whose kinetics is analyzed separately in each of the two regions. By means of a sieving analysis different size fractions of the material are separated and studied. A quasi-Newton fitting algorithm is used to obtain the grain size distribution as best fit to experimental data. The individual fractions are thermogravimetrically analyzed for deriving the functional relationship between activation energy of the degradation reactions and the particle size. Such functional relationship turns out to be crucial to evaluate the moments of the activation energy distribution, which is unknown in terms of the distribution calculated by sieve analysis. From the knowledge of moments one can reconstruct the reaction conversion. The method is applied first to the volatilization region, then to the decomposition region. The comparison with the experimental data reveals that the method reproduces the experimental conversion with an accuracy of 5-10% in the volatilization region and of 3-5% in the decomposition region.

  10. Computer calculations of activation energy for pyrolysis from thermogravimetric curves

    International Nuclear Information System (INIS)

    Hussain, R.

    1994-01-01

    A BASIC programme to determine energy of activation for the degradation of polymers has been described. The calculations are based on the results of thermogravimetric curves. This method is applicable for those polymers which produce volatile products upon thermal degradation. (author)

  11. A new VME timing module: TG8

    International Nuclear Information System (INIS)

    Beetham, C.G.; Daems, G.; Lewis, J.; Puccio, B.

    1992-01-01

    The two accelerator divisions of CERN, namely PS and SL, are defining a new common control system based on PC, VME and Workstations. This has provided an opportunity to review both central timing systems and to come up with common solutions. The result was, amongst others, the design of a unique timing module, called TG8. The TG8 is a multipurpose VME module, which receives messages distributed over a timing network. These messages include timing information, clock plus calendar and telegrams instructing the CERN accelerators on the characteristics of the next beam to be produced. The TG8 compares incoming messages with up to 256 programmed actions. An action consists of two parts, a trigger which matches an incoming message and what to do when the match occurs. The latter part may optionally create an output pulse on one of the eight output channels and/or a bus interrupt, both with programmable delay and telegram conditioning. (author)

  12. Transglutaminase (TG) involvement in early embryogenesis

    International Nuclear Information System (INIS)

    Maccioni, R.B.; Arechaga, J.

    1986-01-01

    Transglutaminase (TG) has been examined in different stages of preimplantation mouse embryogenesis. The specific activity of this enzyme in the soluble cellular fraction increases 2-fold from 2-cell embryos to 8-cell morulae and 4-fold from 2-cell embryos to blastocyst. The same developmental profile was seen when either N,N-dimethylcasein or endogenous substrates were used in the TG assay. Using high-speed supernatants from different stage embryos as a source of enzyme and [ 3 H]putrescine as acyl acceptor, the major acyl donor components were tubulin and a high molecular weight (HMW) cross-linkage product, as assessed by electrophoresis and immunoblotting. When either assembled or monomeric cytoskeleton proteins were compared as subtrates, microtubules were the best acyl donors. These studies indicate that TG activity is modulated during the changing demands of blastomeres for microtubule cytoskeleton in early embryogenesis

  13. Characterization of Amazon fibers of the peach palm, balsa, and babassu by XDR, TGA and NMR; Caracterizacao das fibras amazonicas de pupunha, babacu e balsa atraves de DRX, TG e RMN

    Energy Technology Data Exchange (ETDEWEB)

    Martins, Maria A.; Marconcini, Jose M., E-mail: mariaalice@cnpdia.embrapa.br [Embrapa Instrumentacao, Sao Carlos-SP (Brazil); Morelli, Carolina L.; Marinelli, Alessandra L.; Bretas, Rosario E.S. [Universidade Federal de Sao Carlos - UFSCar, Sao Carlos, SP (Brazil)

    2011-07-01

    The aim of this work was to present the results by testing X-ray diffraction (XRD), thermogravimetric analysis (TG), nuclear magnetic resonance (NMR) and determining the moisture content of the peach palm, balsa and babassu fibers for assessing the feasibility of composite materials. The fibers of peach palm, balsa and babassu showed characteristic chemical structure of lignocellulosic material, and good thermal stability up to 220 deg C. The fiber with the highest crystallinity index (Ic) is the peach palm (72%) and the less crystalline is the babassu (37%), while the balsa fibers have Ic equal to 64%. The results have shown that these fibers can be used in the manufacture of composite materials. (author)

  14. Thermogravimetric studies on the silicothermic reduction of uranium tetrafluoride under nitrogen

    International Nuclear Information System (INIS)

    Venkataramani, R.; Bhatt, Y.J.; Krishnamurthy, N.; Garg, S.P.

    1986-01-01

    This paper presents details of the experimental procedure and results obtained by thermogravimetric studies on the preparation of uranium nitrides by silicothermic reduction of uranium tetrafluoride under a nitrogen atmosphere. The folowing sequential steps are involved during the reaction: 4UF 4 +Si->4UF 3 +SiF 4 (g), 2UF 3 +Si+N 2 ->2UNF+SiF 4 (g), 4UNF+Si+N 2 ->2U 2 N 3 +SiF 4 (g), the uranium sesquintride U 2 N 3 obtained in the above process then decomposed at 1370 K under a dynamic vacuum of less than 10 -2 Tor to yield uranium mononitride of purity better than 99.9%, according to reaction 2U 2 N 3 ->4UN+N 2 (g). The chemical composition of the intermediate products formed during the sequential steps of the process, assessed by thermogravimetric and differential thermogravimetric studies, were further confirmed by chemical and X-ray analysis

  15. Aging of Dielectric Properties below Tg

    DEFF Research Database (Denmark)

    Olsen, Niels Boye; Dyre, Jeppe; Christensen, Tage Emil

    The dielectric loss at 1Hz in TPP is studied during a temperature step from one equilibrium state to another. In the applied cryostate the temperature can be equilibrated on a timescale of 1 second. The aging time dependence of the dielectric loss is studied below Tg applying temperature steps...

  16. Thermogravimetric control of intermediate compounds in uranium metallurgy

    International Nuclear Information System (INIS)

    Gasco Sanchez, L.; Fernandez Cellini, R.

    1959-01-01

    The thermal decomposition of some intermediate compounds in the metallurgy of the uranium as uranium peroxide, ammonium uranate, uranium and ammonium penta-fluoride, uranium tetrafluoride and uranous oxide has been study by means of the Chevenard's thermo balance. Some data on pyrolysis of synthetic mixtures of intermediate compounds which may occasionally appear during the industrial process, are given. Thermogravimetric methods of control are suggested, usable in interesting products in the uranium metallurgy. (Author) 20 refs

  17. Thermal behaviors of mechanically activated pyrites by thermogravimetry (TG)

    International Nuclear Information System (INIS)

    Hu Huiping; Chen Qiyuan; Yin Zhoulan; Zhang Pingmin

    2003-01-01

    The thermal decompositions of mechanically activated and non-activated pyrites were studied by thermogravimetry (TG) at the heating rate of 10 K min -1 in argon. Results indicate that the initial temperature of thermal decomposition (T di ) in TG curves for mechanically activated pyrites decreases gradually with increasing the grinding time. The specific granulometric surface area (S G ), the structural disorder of mechanically activated pyrites were analyzed by X-ray diffraction laser particle size analyzer, and X-ray powder diffraction analysis (XRD), respectively. The results show that the S G of mechanically activated pyrites remains almost constant after a certain grinding time, and lattice distortions (ε) rise but the crystallite sizes (D) decrease with increasing the grinding time. All these results imply that the decrease of T di in TG curves of mechanically activated pyrites is mainly caused by the increase of lattice distortions ε and the decrease of the crystallite sizes D of mechanically activated pyrite with increasing the grinding time. The differences in the reactivity between non-activated and mechanically activated pyrites were observed using characterization of the products obtained from 1 h treatment of non-activated and mechanically activated pyrites at 713 K under inert atmosphere and characterization of non-activated and mechanically activated pyrites exposed to ambient air for a certain period

  18. TG 220 MW hydraulic control system diagnostics

    International Nuclear Information System (INIS)

    Svabcik, A.

    1996-01-01

    The TG power output control system comprises a hydraulic and an electronic part. TG speed, power output or the main steam header pressure (HPK) depend on the steam flow at the turbine inlet. The steam admission into the turbine is controlled by four control valves and one by-pass valve in case of the HP part and by four capture flap valves in case of the LP part. The task of the SKODA K-220 MW turbine protection and control systems is to provide both the turbine speed and power output control to the setpoint value. Diagnostic measurements were aimed at getting an overview of both technical and functional states of all power output control elements. Principally, it can be stated that some deficiencies of a design nature originating from the manufacturer's factory were revealed and some other deficiencies related to hydraulic control elements functionality were identified more closely by the new method. 5 figs

  19. TG 220 MW hydraulic control system diagnostics

    Energy Technology Data Exchange (ETDEWEB)

    Svabcik, A [Atomova Elektraren Bohunice, Jaslovske Bohunice (Slovakia)

    1997-12-31

    The TG power output control system comprises a hydraulic and an electronic part. TG speed, power output or the main steam header pressure (HPK) depend on the steam flow at the turbine inlet. The steam admission into the turbine is controlled by four control valves and one by-pass valve in case of the HP part and by four capture flap valves in case of the LP part. The task of the SKODA K-220 MW turbine protection and control systems is to provide both the turbine speed and power output control to the setpoint value. Diagnostic measurements were aimed at getting an overview of both technical and functional states of all power output control elements. Principally, it can be stated that some deficiencies of a design nature originating from the manufacturer`s factory were revealed and some other deficiencies related to hydraulic control elements functionality were identified more closely by the new method. 5 figs.

  20. Clinical electron beam dosimetry: transition from AAPM TG-25 to AAPM TG-70

    International Nuclear Information System (INIS)

    Mihailidis, Dimitris

    2017-01-01

    The absolute calibration of clinical electron beams is increasingly based on TG-51 protocol. In addition, recently published dosimetry data on electrons beams bring up the question of how would one need to modify the widely used TG-25 that originally was based on TG-21 calibration protocol? The answer to the question is given by the recently published TG-70. This new protocol operates as supplement and update to TG-25 on issues that need to be modified because of TG-51 approach to electron dosimetry and because of newer data on clinical electron beams. It describes in detail the procedure of converting measured depth-ionization curves with ion chambers into depth-dose curves, making use of recently published stopping-power ratios and other conversion factors. It also describes the use of water equivalent phantoms to perform relative electron dosimetry based on recently published conversions factors. The report discusses small and irregularly shaped electron field dosimetry using the concept of lateral buildup ratio (LBR) as an avenue to evaluate electronic equilibrium and compute dose per MU for those fields. Finally, it gives some common clinical examples where electron beam dosimetry are applied

  1. Kinetics of reaction dimer fatty acid C_36 with 1,9 diamino nonane and determination of thermodynamic constants by use of thermogravimetric analysis tga, and rheological constants for the resulted polyamide

    International Nuclear Information System (INIS)

    Mohammad, H.; Falah, Al; Hammoy, M.

    2014-01-01

    Study the kinetics degradation of poly (dimeric acid C_36 with 1.9 – diamino nonane) was carried out by thermal analysis (TGA), and thermodynamic and equilibrium constants have been defined, moreover, study the kinetics of reaction between 1.9 – diamino nonane and dimer fatty acid C_36 was carried out in molten state, the reaction was performed at 160°, the acid value, and percentage of carboxylic functions of the product were determined. The polyamidation reaction was found to be of overall second order until conversion of 97% at 160°, then the order of reaction changes. The degree of dispersion, number molecular weight, weight molecular weight ,and viscosity molecular weight have been calculated during different times.The relationships between degree of dispersion, number Average molecular weight, weight average molecular weight, and viscosity molecular weight with time is linear at160°. Spectroscopy studies were carried out by infra-red and ultraviolet spectroscopy (author).

  2. TH-EF-BRC-00: TG-100 Workshop

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2016-06-15

    This Hands-on Workshop will be focused on providing participants with experience with the principal tools of TG 100 and hence start to build both competence and confidence in the use of risk-based quality management techniques. The three principal tools forming the basis of TG 100’s risk analysis: Process mapping, Failure-Modes and Effects Analysis and fault-tree analysis will be introduced with a 5 minute refresher presentation and each presentation will be followed by a 30 minute small group exercise. An exercise on developing QM from the risk analysis follows. During the exercise periods, participants will apply the principles in 2 different clinical scenarios. At the conclusion of each exercise there will be ample time for participants to discuss with each other and the faculty their experience and any challenges encountered. Learning Objectives: To review the principles of Process Mapping, Failure Modes and Effects Analysis and Fault Tree Analysis. To gain familiarity with these three techniques in a small group setting. To share and discuss experiences with the three techniques with faculty and participants. Director, TreatSafely, LLC. Director, Center for the Assessment of Radiological Sciences. Occasional Consultant to the IAEA and Varian.

  3. TH-EF-BRC-00: TG-100 Workshop

    International Nuclear Information System (INIS)

    2016-01-01

    This Hands-on Workshop will be focused on providing participants with experience with the principal tools of TG 100 and hence start to build both competence and confidence in the use of risk-based quality management techniques. The three principal tools forming the basis of TG 100’s risk analysis: Process mapping, Failure-Modes and Effects Analysis and fault-tree analysis will be introduced with a 5 minute refresher presentation and each presentation will be followed by a 30 minute small group exercise. An exercise on developing QM from the risk analysis follows. During the exercise periods, participants will apply the principles in 2 different clinical scenarios. At the conclusion of each exercise there will be ample time for participants to discuss with each other and the faculty their experience and any challenges encountered. Learning Objectives: To review the principles of Process Mapping, Failure Modes and Effects Analysis and Fault Tree Analysis. To gain familiarity with these three techniques in a small group setting. To share and discuss experiences with the three techniques with faculty and participants. Director, TreatSafely, LLC. Director, Center for the Assessment of Radiological Sciences. Occasional Consultant to the IAEA and Varian.

  4. Thermogravimetric kinetic model of the pyrolysis and combustion of an ethylene-vinyl acetate copolymer refuse

    Energy Technology Data Exchange (ETDEWEB)

    Angela N. Garcia; Rafael Font [Universidad de Alicante, Alicante (Spain). Faculty of Sciences

    2004-06-01

    A kinetic study of the pyrolysis as well as the combustion of EVA copolymer refuse originating from the footwear industry was carried out by thermogravimetric analysis. Different runs were performed at heating rates between 5-20{sup o}C min{sup -1} and atmospheres with different percentages of oxygen: 0, 10 and 20% (v/v). Pyrolysis and combustion processes can be simulated by two series reactions. The results obtained indicate that the second reaction begins when the first one is almost finished which implies that a good correlation is also obtained by simulation of the thermal decomposition of two independent fractions. 32 refs., 4 figs., 3 tabs.

  5. TG/DTG, FT-ICR Mass Spectrometry, and NMR Spectroscopy Study of Heavy Fuel Oil

    KAUST Repository

    Elbaz, Ayman M.

    2015-11-12

    There is an increasing interest in the comprehensive study of heavy fuel oil (HFO) due to its growing use in furnaces, boilers, marines, and recently in gas turbines. In this work, the thermal combustion characteristics and chemical composition of HFO were investigated using a range of techniques. Thermogravimetric analysis (TGA) was conducted to study the nonisothermal HFO combustion behavior. Chemical characterization of HFO was accomplished using various standard methods in addition to direct infusion atmospheric pressure chemical ionization Fourier transform ion cyclotron resonance mass spectrometry (APCI-FTICR MS), high resolution 1H nuclear magnetic resonance (NMR), 13C NMR, and two-dimensional heteronuclear multiple bond correlation (HMBC) spectroscopy. By analyzing thermogravimetry and differential thermogravimetry (TG/DTG) results, three different reaction regions were identified in the combustion of HFO with air, specifically, low temperature oxidation region (LTO), fuel deposition (FD), and high temperature oxidation (HTO) region. At the high end of the LTO region, a mass transfer resistance (skin effect) was evident. Kinetic analysis in LTO and HTO regions was conducted using two different kinetic models to calculate the apparent activation energy. In both models, HTO activation energies are higher than those for LTO. The FT-ICR MS technique resolved thousands of aromatic and sulfur containing compounds in the HFO sample and provided compositional details for individual molecules of three major class species. The major classes of compounds included species with one sulfur atom (S1), with two sulfur atoms (S2), and purely hydrocarbons (HC). The DBE (double bond equivalent) abundance plots established for S1 and HC provided additional information on their distributions in the HFO sample. The 1H NMR and 13C NMR results revealed that nearly 59% of the 1H nuclei were distributed as paraffinic CH2 and 5% were in aromatic groups. Nearly 21% of 13C nuclei were

  6. Thermogravimetric study of γ-irradiated lanthanum oxalate

    International Nuclear Information System (INIS)

    Nayak, H.; Bhatta, D.

    2000-01-01

    Thermogravimetric study of La 2 (C 2 O 4 ) 3 , exposed to different doses (5.0 - 50.0 x 10 -2 MGy) of γ-rays has been carried out. Marginal effect is observed at lower doses which is prominent at higher dose (5.0 x 10 -1 MGy). The radiolytic damaged entities, generated by irradiation favours the reaction by creating new potential nucleation centres in the lattice. The solid product, La 2 O 3 formed by irradiation also acts as a heterogeneous catalyst and brings out changes in the reactivity of the solid. (author)

  7. A novel quantification method of pantaprazole sodium monohydrate in sesquihydrate by thermogravimetric analyzer.

    Science.gov (United States)

    Reddy, V Ranga; Rajmohan, M Anantha; Shilpa, R Laxmi; Raut, Dilip M; Naveenkumar, Kolla; Suryanarayana, M V; Mathad, Vijayavitthal T

    2007-04-11

    To demonstrate the applicability of thermogravimetric analyzer as a tool for the quantification of pantaprazole sodium monohydrate in sesquihydrate, studies have been conducted. Thermal analysis (DSC, TGA) crystallographic (PXRD) and spectroscopic techniques (FT-IR) were used for the characterization of the polymorphs. Thermogravimetric analysis (TGA) analysis was explored by high-resolution dynamic (Hi-Res-dynamic) and high-resolution modulated (Hi-Res-modulated) test procedures to quantify the hydrate polymorphic mixtures. The two polymorphic forms exhibited significant differences and good resolution in the second derivative thermogram generated by Hi-Res-modulated test procedure. Thus, the TGA with Hi-Res-modulated test procedure was considered for the quantification of monohydrate in sesquihydrate. The calibration plot was constructed from the known mixtures of two polymorphs by plotting the peak area of the second derivative thermogram against the weight percent of monohydrate. Using this novel approach, 1 wt% limit of detection (LOD) was achieved. The polymorphic purity results, obtained by TGA in Hi-Res-modulated test procedure were found to be in good agreement with the results predicted by FT-IR and was comparable with the actual values of the known polymorphic mixtures. The Hi-Res-modulated TGA technique is very simple and easy to perform the analysis.

  8. Automation of a McBain-Bakr-type thermogravimetric analyzer using a digital image correlation technique

    International Nuclear Information System (INIS)

    Trexler, M.D.; Sanders, T.H. Jr.; Singh, P.M.

    2006-01-01

    Thermogravimetric analysis was used to obtain corrosion kinetics data for several materials in high-temperature environments. A thermogravimetric analyzer has been developed that uses a McBain-Bakr quartz spring balance in conjunction with a digital image acquisition and analysis package to accurately characterize materials through image correlation. This provides a new method for automatically measuring mass changes continuously with a variable resolution depending on the spring component. The decomposition of calcium oxalate was used to verify the validity of the technique. The results show two reactions, whose reaction temperatures were determined by the intercept method, upon heating to 650 deg. C. The mass loss at the first reaction temperature, 200 deg. C, was 20% and a 30% loss was observed at 500 deg. C. Comparison of the experimentally obtained results with those of other researchers who used commercial instruments suggests that the method of using digital image analysis in conjunction with a spring to monitor mass change is a viable and accurate replacement for automatic electrobalances and cathetometers for thermal analysis of materials. Additional comparison between corrosion tests performed on SA210 steel in H 2 S using both a commercial thermobalance and the developed technique confirmed that high-temperature corrosion can be monitored accurately with the proposed method

  9. Thermogravimetric analysis of multi-stage hydropyrolysis of different coals

    Energy Technology Data Exchange (ETDEWEB)

    Li, W.; Wang, N.; Li, B [Chinese Academy of Sciences, Taiyuan (China). State Key Lab. of Coal Conversion

    2001-09-01

    Based on the characteristic of hydropyrolysis (HyPy), a multi-stage MHyPy of different coals was investigated using thermogravimetry. The results show that keeping the near peak temperature for some time in HyPy process can obviously increase the conversion rate, which is believed due to the full match between formation rate of free radicals and supply of hydrogen. The fast heating in MHyPy process results in the same conversion rate as that of the slow heating in HyPy process, which leads to the less reaction time and high yield of oil. The effect of MHyPy depends on the coal structure itself and it is notable for the coal with high H/C ratio. This suggests that the external hydrogen promotes the reaction between intrinsic hydrogen and free radicals. The MHyPy improves the removal of sulfur and nitrogen. 5 refs., 7 figs., 2 tabs.

  10. Carbon elimination from silicon kerf: Thermogravimetric analysis and mechanistic considerations.

    Science.gov (United States)

    Vazquez-Pufleau, Miguel; Chadha, Tandeep S; Yablonsky, Gregory; Biswas, Pratim

    2017-01-18

    40% of ultrapure silicon is lost as kerf during slicing to produce wafers. Kerf is currently not being recycled due to engineering challenges and costs associated with removing its abundant impurities. Carbon left behind from the lubricant remains as one of the most difficult contaminants to remove in kerf without significant silicon oxidation. The present work enables to better understand the mechanism of carbon elimination in kerf which can aid the design of better processes for kef recycling and low cost photovoltaics. In this paper, we studied the kinetics of carbon elimination from silicon kerf in two atmospheres: air and N 2, under a regime of no-diffusion-limitation. We report the apparent activation energy in both atmospheres using three methods: Kissinger, and two isoconversional approaches. In both atmospheres, a bimodal apparent activation energy is observed, suggesting a two stage process. A reaction mechanism is proposed in which (a) C-C and C-O bond cleavage reactions occur in parallel with polymer formation; (b) at higher temperatures, this polymer fully degrades in air but leaves a tarry residue in N 2 that accounts for about 12% of the initial total carbon.

  11. Investigation on caloric requirement of biomass pyrolysis using TG-DSC analyzer

    Energy Technology Data Exchange (ETDEWEB)

    He Fang [Institute of Utilization of Biomass, Shandong University of Technology, No. 12, Zhangzhou Road, Zibo, Shandong 255049 (China)]. E-mail: hf@sdut.edu.cn; Yi Weiming [Institute of Utilization of Biomass, Shandong University of Technology, No. 12, Zhangzhou Road, Zibo, Shandong 255049 (China); Bai Xueyuan [Institute of Utilization of Biomass, Shandong University of Technology, No. 12, Zhangzhou Road, Zibo, Shandong 255049 (China)

    2006-09-15

    The caloric requirement of biomass pyrolysis has an important influence on the course of the thermal conversion. However, precise data are difficult to achieve by the current calculation method because of the complexity of the process. A new method for achieving the caloric requirement of the process by integrating the differential scanning calorimetry (DSC) curves was proposed after the simultaneous thermal analyzer (TG-DSC) and DSC curves were investigated. Experiments were conducted for wheat straw, cotton stalk, pine and peanut shell on a Netsch STA 449C analyzer. Powder samples were put into a platinum crucible with a lid on a high accuracy DSC-cp sample holder in the furnace and then heated from ambient temperature up to the maximum temperature of 973 K at the heating rate of 10 K/min in the analyzer. The product gases were swept away by 25 ml/min nitrogen. Mass changes (TG) and calorimetric effects (DSC) were recorded and analyzed. The process was investigated in detail through comparison of the DTG (differential thermogravimetric) and DSC curves of wheat straw. After the water influence in the DSC was eliminated, the relationship of the caloric requirement with the temperature of the aforementioned dry biomass was obtained by integrating the DSC curve. The results showed that 523 kJ, 459 kJ, 646 kJ and 385 kJ were required, respectively, to increase the temperature of 1 kg of dried wheat straw, cotton stalk, pine and peanut from 303 K to 673 K.

  12. Nickel hydroxide electrode. 3: Thermogravimetric investigations of nickel (II) hydroxides

    Science.gov (United States)

    Dennstedt, W.; Loeser, W.

    1982-01-01

    Water contained in Ni hydroxide influences its electrochemical reactivity. The water content of alpha and beta Ni hydroxides is different with respect to the amount and bond strength. Thermogravimetric experiments show that the water of the beta Ni hydroxides exceeding the stoichiometric composition is completely removed at 160 deg. The water contained in the interlayers of the beta hydroxide, however, is removed only at higher temperatures, together with the water originating from the decomposition of the hydroxide. These differences are attributed to the formation of II bonds within the interlayers and between interlayers and adjacent main layers. An attempt is made to explain the relations between water content and the oxidizability of the Ni hydroxides.

  13. Hydrogen Adsorption in Zeolite Studied with Sievert and Thermogravimetric Methods

    International Nuclear Information System (INIS)

    Lesnicenoks, P; Sivars, A; Grinberga, L; Kleperis, J

    2012-01-01

    Natural clinoptilolite (mixture from clinoptilolite, quartz and muscovite) is activated with palladium and tested for hydrogen adsorption capability at temperatures RT - 200°C. Thermogravimetric and volumetric methods showed that zeolite activated with palladium (1.25%wt) shows markedly high hydrogen adsorption capacity - up to 3 wt%. Lower amount of adsorbed hydrogen (∼1.5 wt%) was found for raw zeolite and activated with higher amount of palladium sample. Hypothesis is proposed that the heating of zeolite in argon atmosphere forms and activates the pore structure in zeolite material, where hydrogen encapsulation (trapping) is believed to occur when cooling down to room temperature. An effect of catalyst (Pd) on hydrogen sorption capability is explained by spillover phenomena were less-porous fractions of natural clinoptilolite sample (quartz and muscovite) are involved.

  14. Aged Tg2576 mice are impaired on social memory and open field habituation tests.

    Science.gov (United States)

    Deacon, R M J; Koros, E; Bornemann, K D; Rawlins, J N P

    2009-02-11

    In a previous publication [Deacon RMJ, Cholerton LL, Talbot K, Nair-Roberts RG, Sanderson DJ, Romberg C, et al. Age-dependent and -independent behavioral deficits in Tg2576 mice. Behav Brain Res 2008;189:126-38] we found that very few cognitive tests were suitable for demonstrating deficits in Tg2576 mice, an amyloid over-expression model of Alzheimer's disease, even at 23 months of age. However, in a retrospective analysis of a separate project on these mice, tests of social memory and open field habituation revealed large cognitive impairments. Controls showed good open field habituation, but Tg2576 mice were hyperactive and failed to habituate. In the test of social memory for a juvenile mouse, controls showed considerably less social investigation on the second meeting, indicating memory of the juvenile, whereas Tg2576 mice did not show this decrement.As a control for olfactory sensitivity, on which social memory relies, the ability to find a food pellet hidden under wood chip bedding was assessed. Tg2576 mice found the pellet as quickly as controls. As this test requires digging ability, this was independently assessed in tests of burrowing and directly observed digging. In line with previous results and the hippocampal dysfunction characteristic of aged Tg2576 mice, they both burrowed and dug less than controls.

  15. A Thermogravimetric Study of the Behaviour of Biomass Blends During Combustion

    Directory of Open Access Journals (Sweden)

    Ivo Jiříček

    2012-01-01

    Full Text Available The ignition and combustion behavior of biomass and biomass blends under typical heating conditions were investigated. Thermogravimetric analyses were performed on stalk and woody biomass, alone and blended with various additive weight ratios. The combustion process was enhanced by adding oxygen to the primary air. This led to shorter devolatilization/pyrolysis and char burnout stages, which both took place at lower temperatures than in air alone. The results of the ignition study of stalk biomass show a decrease in ignition temperature as the particle size decreases. This indicates homogeneous ignition, where the volatiles burn in the gas phase, preventing oxygen from reaching the particle surface.The behavior of biomass fuels in the burning process was analyzed, and the effects of heat production and additive type were investigated. Mixing with additives is a method for modifying biofuel and obtaining a more continuous heat release process. Differential scanning calorimetric-thermogravimetric (DSC-TGA analysis revealed that when the additive is added to biomass, the volatilization rate is modified, the heat release is affected, and the combustion residue is reduced at the same final combustion temperature.

  16. Thermogravimetric investigation of the co-combustion between the pyrolysis oil distillation residue and lignite.

    Science.gov (United States)

    Li, Hao; Xia, Shuqian; Ma, Peisheng

    2016-10-01

    Co-combustion of lignite with distillation residue derived from rice straw pyrolysis oil was investigated by non-isothermal thermogravimetric analysis (TGA). The addition of distillation residue improved the reactivity and combustion efficiency of lignite, such as increasing the weight loss rate at peak temperature and decreasing the burnout temperature and the total burnout. With increasing distillation residue content in the blended fuels, the synergistic interactions between distillation residue and lignite firstly increased and then decreased during co-combustion stage. Results of XRF, FTIR, (13)C NMR and SEM analysis indicated that chemical structure, mineral components and morphology of samples have great influence on the synergistic interactions. The combustion mechanisms and kinetic parameters were calculated by the Coats Redfern model, suggesting that the lowest apparent activation energy (120.19kJ/mol) for the blended fuels was obtained by blending 60wt.% distillation residue during main co-combustion stage. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. TG-FTIR Study of the Influence of potassium Chloride on Wheat Straw Pyrolysis

    DEFF Research Database (Denmark)

    Jensen, Anker; Dam-Johansen, Kim; Wójtowicz, M.A.

    1998-01-01

    of products into char, tar and gas. In this work, a combination of thermogravimetry and evolved gas analysis by Fourier transform infrared analysis (TG-FTIR) has been applied to study the influence of potassium chloride (KCl) on wheat straw pyrolysis. Raw straw, washed straw and washed straw impregnated...

  18. Local lymph node assay: how testing laboratories apply OECD TG 429 for REACH purposes.

    Science.gov (United States)

    Rovida, Costanza

    2011-01-01

    The Local Lymph Node Assay (LLNA) is the official method for assessing the allergic contact dermatitis potential of chemicals for the purposes of REACH regulation. The LLNA went through a validation process that allowed the delineation of a robust protocol for performing new tests. The OECD accepted this method in 2002 and published OECD TG 429. The European Chemical Agency (ECHA) recently published data that were submitted in the registration dossiers of chemicals. This database was analysed to determine how testing laboratories apply OECD TG 429. This analysis comes after a detailed analysis of four full study reports that were also prepared for REACH purposes. Although the majority of the tests are fully compliant with OECD TG 429, some showed major deviations, and a number of others used more animals than necessary. This suggests that in vivo tests need to be planned more carefully and consciously to obtain meaningful results with the minimum animal number necessary.

  19. TG Grammar's Implications for the Foreign Language Teaching

    Institute of Scientific and Technical Information of China (English)

    殷彩

    2009-01-01

    Chomsky's Transformational-Generative (TG) grammar is another revolution to linguistics after Saussure's strueturalism, and it plays an important role in the modem linguistics. Introducing the research perspective and method of TG grammar, this paper analyses its implications for the foreign language teaching.

  20. Thermogravimetric characteristics and kinetics of pyrolysis of coal blends

    Directory of Open Access Journals (Sweden)

    Juan Manuel Barraza-Burgos

    2015-01-01

    Full Text Available Las características termogravimétricas y la cinética de la pirolisis de mezclas de carbones se investigaron usando un analizador termogravimétrico con velocidades de calentamiento de 20°C/min desde temperatura ambiente hasta 850°C. Las muestras de carbones originales se obtuvieron de tres regiones colombianas: Valle del Cauca (VAL, Antioquia (ANT y Cundinamarca (CUN. Las muestras de carbones mezclados (50-50 % p/p se produjeron a partir de carbones originales de esas tres regiones. Las curvas de pérdida de peso de los carbones obtenidas por termogravimetría (TG mostraron diferentes tendencias. Esas curvas podrían indicar que los comportamientos durante la pirólisis no fueron similares debido a que las estructuras moleculares de los carbones tienen diferentes enlaces químicos. Además, un análisis cinético se realizó para ajustar los datos de TG. En el análisis, se supuso que una reacción química única describe la pirólisis de carbones originales y mezcla de carbones. Una relación de Sinergia de Energía de Activación (SAER se defi nió con el fi n de determinar el efecto aditivo entre los carbones y la mezcla de carbones durante la pirólisis. Los resultados obtenidos mostraron que la SAER de la mezcla CUN-VAL está cerca de la unidad, lo que signifi ca que la mezcla tiene un comportamiento aditivo. Sin embargo, el SAER de la mezcla ANT-VAL es inferior a uno, mientras que de la mezcla ANT-CUN es mayor que uno. Esto sugiere que los carbones VAL y CUN podrían tener una reacción no aditiva cuando se mezclan con el carbón ANT.

  1. The follow-up of patients with differentiated thyroid cancer and undetectable thyroglobulin (Tg) and Tg antibodies during ablation

    NARCIS (Netherlands)

    Phan, Ha T. T.; Jager, Pieter L.; van der Wal, Jacqueline E.; Sluiter, Wim J.; Plukker, John T. M.; Dierckx, Rudi A. J. O.; Wolffenbuttel, Bruce H. R.; Links, Thera P.

    Objective: This retrospective study describes the rote of serum thyroglobulin (Tg) in relation to tumor characteristics in the prediction of persistent/recurrent disease in patients with differentiated thyroid cancer (DTC) with negative Tg at the time of ablation. Design: Between 1989 and 2006, 94

  2. Tg.rasH2 Mice and not CByB6F1 Mice Should Be Used for 28-Day Dose Range Finding Studies Prior to 26-Week Tg.rasH2 Carcinogenicity Studies.

    Science.gov (United States)

    Paranjpe, Madhav G; Belich, Jessica; Vidmar, Tom J; Elbekai, Reem H; McKeon, Marie; Brown, Caren

    Our recent retrospective analysis of data, collected from 29 Tg.rasH2 mouse carcinogenicity studies, determined how successful the strategy of choosing the high dose for the 26-week studies was based on the estimated maximum tolerated dose (EMTD) derived from earlier 28-day dose range finding (DRF) studies conducted in CByB6F1 mice. Our analysis demonstrated that the high doses applied at EMTD in the 26-week Tg.rasH2 studies failed to detect carcinogenic effects. To investigate why the dose selection process failed in the 26-week carcinogenicity studies, the initial body weights, terminal body weights, body weight gains, food consumption, and mortality from the first 4 weeks of 26-week studies with Tg.rasH2 mice were compared with 28-day DRF studies conducted with CByB6F1 mice. Both the 26-week and the earlier respective 28-day studies were conducted with the exact same vehicle, test article, and similar dose levels. The analysis of our results further emphasizes that the EMTD and subsequent lower doses, determined on the basis of the 28-day studies in CByB6F1 mice, may not be an accurate strategy for selecting appropriate dose levels for the 26-week carcinogenicity studies in Tg.rasH2 mice. Based on the analysis presented in this article, we propose that the Tg.rasH2 mice and not the CByB6F1 mice should be used in future DRF studies. The Tg.rasH2 mice demonstrate more toxicity than the CByB6F1 mice, possibly because of their smaller size compared to CByB6F1 mice. Also, the Tg.rasH2 males appear to be more sensitive than the female Tg.rasH2 mice.

  3. Non-shoring construction for T/G pedestal beams

    International Nuclear Information System (INIS)

    Abe, T.

    1992-01-01

    The T/G pedestal construction work has been the critical path within the T/B construction work of BWR type nuclear power plant. In order to meet the requirement of shortening the construction period and improved in safety on a Turbine Building (T/B) construction work, Non-soring construction for T/G Pedestal Beams was developed. By applying this method to T/G pedestal construction work, we succeeded in shortening the T/B construction period and improvement in safety significantly. (author)

  4. Comparison of TG-43 and TG-186 in breast irradiation using a low energy electronic brachytherapy source

    International Nuclear Information System (INIS)

    White, Shane A.; Landry, Guillaume; Reniers, Brigitte; Fonseca, Gabriel Paiva; Holt, Randy; Rusch, Thomas; Beaulieu, Luc; Verhaegen, Frank

    2014-01-01

    Purpose: The recently updated guidelines for dosimetry in brachytherapy in TG-186 have recommended the use of model-based dosimetry calculations as a replacement for TG-43. TG-186 highlights shortcomings in the water-based approach in TG-43, particularly for low energy brachytherapy sources. The Xoft Axxent is a low energy ( w,m ) and dose to medium (D m,m ), for the heterogeneous simulations. All results were compared against TG-43-based dose distributions and evaluated using dose ratio maps and DVH metrics. Changes in skin and PTV dose were highlighted. Results: All simulated heterogeneous models showed a reduced dose to the DVH metrics that is dependent on the method of dose reporting and patient geometry. Based on a prescription dose of 34 Gy, the average D 90 to PTV was reduced by between ∼4% and ∼40%, depending on the scoring method, compared to the TG-43 result. Peak skin dose is also reduced by 10%–15% due to the absence of backscatter not accounted for in TG-43. The balloon applicator also contributed to the reduced dose. Other ROIs showed a difference depending on the method of dose reporting. Conclusions: TG-186-based calculations produce results that are different from TG-43 for the Axxent source. The differences depend strongly on the method of dose reporting. This study highlights the importance of backscatter to peak skin dose. Tissue heterogeneities, applicator, and patient geometries demonstrate the need for a more robust dose calculation method for low energy brachytherapy sources

  5. Influence of the Zeolite ZSM-5 on Catalytic Pyrolysis of Biomass via TG-FTIR

    Directory of Open Access Journals (Sweden)

    Ze Wang

    2015-06-01

    Full Text Available Bio-oil from the pyrolysis of biomass is an important renewable source for liquid fuel. However, the application of bio-oil has been severely restricted due to its high viscosity, acidity, and low heating value. Thus, it has been necessary to upgrade bio-oil for automobile fuel via catalytic deoxygenation reactions. Herein, the effects of the zeolite ZSM-5 on the pyrolysis of four biomass materials (corn cob, corn straw, pine powder, and cellulose were investigated via TG-FTIR (thermogravimetric analyzer coupled with a Fourier transform infrared spectrometer to better understand the working mechanism of ZSM-5. The contents of the products of H2O, CO, CO2, and the C-O, C=O, and OH groups evolved with increasing pyrolytic temperature were monitored by FTIR. It was found that the relative contents of the C-O and C=O groups were decreased under the catalysis of ZSM-5, while the formations of CO, H2O, and the OH containing compounds were promoted. To explain the regulations, reaction routes were speculated and the catalytic conversion mechanisms were deduced.

  6. TG-FTIR, DSC and quantum chemical studies of the thermal decomposition of quaternary methylammonium halides

    International Nuclear Information System (INIS)

    Sawicka, Marlena; Storoniak, Piotr; Skurski, Piotr; Blazejowski, Jerzy; Rak, Janusz

    2006-01-01

    The thermal decomposition of quaternary methylammonium halides was studied using thermogravimetry coupled to FTIR (TG-FTIR) and differential scanning calorimetry (DSC) as well as the DFT, MP2 and G2 quantum chemical methods. There is almost perfect agreement between the experimental IR spectra and those predicted at the B3LYP/6-311G(d,p) level: this has demonstrated for the first time that an equimolar mixture of trimethylamine and a methyl halide is produced as a result of decomposition. The experimental enthalpies of dissociation are 153.4, 171.2, and 186.7 kJ/mol for chloride, bromide and iodide, respectively, values that correlate well with the calculated enthalpies of dissociation based on crystal lattice energies and quantum chemical thermodynamic barriers. The experimental activation barriers estimated from the least-squares fit of the F1 kinetic model (first-order process) to thermogravimetric traces - 283, 244 and 204 kJ/mol for chloride, bromide and iodide, respectively - agree very well with theoretically calculated values. The theoretical approach assumed in this work has been shown capable of predicting the relevant characteristics of the thermal decomposition of solids with experimental accuracy

  7. A Sensitive Tg Assay or rhTSH Stimulated Tg : What's the Best in the Long-Term Follow-Up of Patients with Differentiated Thyroid Carcinoma?

    NARCIS (Netherlands)

    Persoon, Adrienne C. M.; Jager, Pieter L.; Sluiter, Wim J.; Plukker, John T. M.; Wolffenbuttel, Bruce H. R.; Links, Thera P.

    2007-01-01

    Sensitivity of thyroglobulin (Tg) measurement in the follow-up of differentiated thyroid carcinoma (DTC) can be optimized by using a sensitive Tg assay and rhTSH stimulation. We evaluated the diagnostic yield of a sensitive Tg assay and rhTSH stimulated Tg in the detection of recurrences in the

  8. Local confidence limits for IMRT and VMAT techniques: a study based on TG119 test suite

    International Nuclear Information System (INIS)

    Thomas, M.; Chandroth, M.

    2014-01-01

    The aim of this study was to generate a local confidence limit (CL) for intensity modulated radiation therapy (IMRT) and volumetric modulated arc therapy (VMAT) techniques used at Waikato Regional Cancer Centre. This work was carried out based on the American Association of Physicists in Medicine (AAPM) Task Group (TG) 119 report. The AAPM TG 119 report recommends CLs as a bench mark for IMRT commissioning and delivery based on its multiple institutions planning and dosimetry comparisons. In this study the locally obtained CLs were compared to TG119 benchmarks. Furthermore, the same bench mark was used to test the capabilities and quality of the VMAT technique in our clinic. The TG 119 test suite consists of two primary and four clinical tests for evaluating the accuracy of IMRT planning and dose delivery systems. Pre defined structure sets contoured on computed tomography images were downloaded from AAPM website and were transferred to a locally designed phantom. For each test case two plans were generated using IMRT and VMAT optimisation. Dose prescriptions and planning objectives recommended by TG119 report were followed to generate the test plans in Eclipse Treatment Planning System. For each plan the point dose measurements were done using an ion chamber at high dose and low dose regions. The planar dose distribution was analysed for percentage of points passing the gamma criteria of 3 %/3 mm, for both the composite plan and individual fields of each plan. The CLs were generated based on the results from the gamma analysis and point dose measurements. For IMRT plans, the CLs obtained were (1) from point dose measurements: 2.49 % at high dose region and 2.95 % for the low dose region (2) from gamma analysis: 2.12 % for individual fields and 5.9 % for the composite plan. For VMAT plans, the CLs obtained were (1) from point dose measurements: 2.56 % at high dose region and 2.6 % for the low dose region (2) from gamma analysis: 1.46 % for individual fields and 0

  9. Offgas Analysis and Pyrolysis Mechanism of Activated Carbon from Bamboo Sawdust by Chemical Activation With KOH

    Institute of Scientific and Technical Information of China (English)

    TIAN Yong; LIU Ping; WANG Xiufang; ZHONG Guoying; CHEN Guanke

    2011-01-01

    Bamboo sawdust was used as the precursor for the multipurpose use of waste.Offgases released during the activation process of bamboo by KOH were investigated quantitatively and qualitatively by a gas analyzer. TG/DTG curves during the pyrolysis process with different impregnation weight ratios (KOH to bamboo) were obtained by a thermogravimetric analyzer. Pyrolysis mechanism of bamboo was proposed. The results showed that the offgases were composed of CO, NO,SO2 and hydrocarbon with the concentration of 1 372, 37, 86, 215 mg/L, respectively. Thermogravimetric analysis indicated that the pyrolytic process mainly experienced two steps. The first was the low temperature activation step (lower than 300 ℃), which was the pre-activation and induction period.The second was the high temperature activation step(higher than 550 ℃), which was a radial activation followed by pore production. The second process was the key to control the pore distribution of the final product.

  10. IMRT Commissioning: application of the AAPM's TG-119; Comissionamento de IMRT: aplicacao do TG-119 da AAPM

    Energy Technology Data Exchange (ETDEWEB)

    Zeppellini, Caroline; Furnari, Laura, E-mail: laurafurnari@hotmail.com [Universidade de Sao Paulo (USP), Sao Paulo, SP (Brazil). Fac. de Medicina. Inst. de Radiologia

    2013-08-15

    In order to verify the commissioning of the planning of intensity-modulated radiation therapy system (IMRT), the TG-119 of the American Association of Physicists in Medicine (AAPM) was applied. Using pre defined targets and normal structures, plans were realized, absolute and relative dose were measured with an ionizing chamber and films, and the results were compared with planned values. The maximum deviation of the measurements with the ionization chamber was 3,6%, but, in the total eleven measurements, only two were bigger than the tolerance limit of 3%, recommended by TG-119. The number of points which passed criteria gamma 3% to 3 mm ranged between 96.36% and 99.92%, all measurements were within the recommended 95%. The confidence limits found for both film and for chamber were lower than those achieved in the TG-119. Our results showed a good concordance with TG-119, what means that the system is adequate for clinical applications. (author)

  11. Characterization of microalga Chlorella as a fuel and its thermogravimetric behavior

    International Nuclear Information System (INIS)

    Rizzo, Andrea Maria; Prussi, Matteo; Bettucci, Lorenzo; Libelli, Ilaria Marsili; Chiaramonti, David

    2013-01-01

    Highlights: ► Proximate and ultimate analysis of two microalgae (Nannochloropsis and Chlorella spp.). ► TGA of Chlorella spp. and Nannochloropsis investigated at 15 °C/min up to 800 °C. ► 1.2 kg of Chlorella pyrolyzed in a novel batch, intermediate pyrolysis pilot reactor at 450 °C. ► Bio-oil from Chlorella oil analysed and compared to pine chips fast pyrolysis oil. ► Bio-oil from Chlorella exhibited superior properties compared to lignocellulosic pyrolysis oil as intermediate energy carrier. -- Abstract: Microalgae are photosynthetic microorganisms living in marine or freshwater environment. In this study, samples of Chlorella spp. and Nannochloropsis from two different origins were analysed to settle a preliminary characterization of these microorganisms as intermediate energy carriers and their properties compared to a conventional lignocellulosic feedstock (pine chips). Both microalgae samples were characterized in terms of elemental composition (CHONS and P) and thermogravimetric behavior. This was investigated through non-isothermal thermogravimetric analysis in nitrogen atmosphere at heating rate of 15 °C min −1 and temperature up to 800 °C. Solid residues produced at 300 °C and 800 °C from TGA were also analysed to determine the ultimate composition of chars. Activation energy, reaction order and pre-exponential factor were calculated for the single step conversion mechanism of 1 g of Chlorella spp. and compared to literature data on Chlorella protothecoides and Spirulina platensis. Calculated kinetic parameters, given as intervals of several determinations, resulted to be: pre-exponential factor (A) 1.47–1.62E6 min −1 , activation energy (E) 7.13–7.92E4 J mol −1 , reaction order (n) 1.69–2.41. 1.2 kg of Chlorella spp. was then processed in a newly designed batch pyrolysis pilot reactor, capable of converting up to 1.5 kg h −1 of material, and pyrolysis liquid collected, analysed and compared with a sample of fast pyrolysis

  12. Thermogravimetric studies of the thermo-oxidative stability of irradiated and unirradiated polyethylene

    International Nuclear Information System (INIS)

    Novakovic, L.; Gal, O.; Markovic, V.; Stannett, V.T.

    1985-01-01

    In part one of this series the effects of a phenolic, an amine and a thioester antioxidant on the thermo-oxidative stability of irradiated and unirradiated low-density polyethylene was reported. In this paper the effects of combined phenolic and thioester stabilizers are described. Isothermal thermogravimetric analysis was used to study the systems. Pronounced synergism was observed with the induction periods, the time when the initial weight loss begins and the 5% weight loss. At about 50% of each stabilizer increases greater than twofold were observed both with the unirradiated and irradiated polymers. The rate constants for oxygen uptake were decreased. However, the rates of degradation at 5% weight loss fell between the values of the two pure stabilizers with no pronounced synergism in either case. In the absence of oxygen little effect of either antioxidant or their mixtures was observed. The corresponding activation energies were somewhat higher, however, with the irradiated samples containing antioxidants. Dynamic thermogravimetry was used for this study. A kinetic analysis indicated that there were somewhat different modes of degradation at lower- and higher-temperature ranges. (author)

  13. Thermogravimetric studies of the thermo-oxidative stability of irradiated and unirradiated polyethylene. 2. Combined antioxidants

    Energy Technology Data Exchange (ETDEWEB)

    Novakovic, L; Gal, O; Markovic, V; Stannett, V T

    1985-01-01

    In part one of this series the effects of a phenolic, an amine and a thioester antioxidant on the thermo-oxidative stability of irradiated and unirradiated low-density polyethylene was reported. In this paper the effects of combined phenolic and thioester stabilizers are described. Isothermal thermogravimetric analysis was used to study the systems. Pronounced synergism was observed with the induction periods, the time when the initial weight loss begins and the 5% weight loss. At about 50% of each stabilizer increases greater than twofold were observed both with the unirradiated and irradiated polymers. The rate constants for oxygen uptake were decreased. However, the rates of degradation at 5% weight loss fell between the values of the two pure stabilizers with no pronounced synergism in either case. In the absence of oxygen little effect of either antioxidant or their mixtures was observed. The corresponding activation energies were somewhat higher, however, with the irradiated samples containing antioxidants. Dynamic thermogravimetry was used for this study. A kinetic analysis indicated that there were somewhat different modes of degradation at lower- and higher-temperature ranges. (author).

  14. Physicotechnical, spectroscopic and thermogravimetric properties of powdered cellulose and microcrystalline cellulose derived from groundnut shells

    Directory of Open Access Journals (Sweden)

    Chukwuemeka P. Azubuike

    2012-09-01

    Full Text Available α-Cellulose and microcrystalline cellulose powders, derived from agricultural waste products, that have for the pharmaceutical industry, desirable physical (flow properties were investigated. α–Cellulose (GCN was extracted from groundnut shell (an agricultural waste product using a non-dissolving method based on inorganic reagents. Modification of this α -cellulose was carried out by partially hydrolysing it with 2N hydrochloric acid under reflux to obtain microcrystalline cellulose (MCGN. The physical, spectroscopic and thermal properties of the derived α-cellulose and microcrystalline cellulose powders were compared with Avicel® PH 101, a commercial brand of microcrystalline cellulose (MCCA, using standard methods. X-ray diffraction and infrared spectroscopy analysis showed that the α-cellulose had lower crystallinity. This suggested that treatment with 2N hydrochloric acid led to an increase in the crystallinity index. Thermogravimetric analysis showed quite similar thermal behavior for all cellulose samples, although the α-cellulose had a somewhat lower stability. A comparison of the physical properties between the microcrystalline celluloses and the α-cellulose suggests that microcrystalline cellulose (MCGN and MCCA might have better flow properties. In almost all cases, MCGN and MCCA had similar characteristics. Since groundnut shells are agricultural waste products, its utilization as a source of microcrystalline cellulose might be a good low-cost alternative to the more expensive commercial brand.

  15. Comparison of TG-43 and TG-186 in breast irradiation using a low energy electronic brachytherapy source

    Energy Technology Data Exchange (ETDEWEB)

    White, Shane A.; Landry, Guillaume; Reniers, Brigitte, E-mail: brigitte.reniers@maastro.nl [Department of Radiation Oncology (MAASTRO), GROW School for Oncology and Developmental Biology, Maastricht University Medical Center (MUMC), Maastricht 6201 BN (Netherlands); Fonseca, Gabriel Paiva [Department of Radiation Oncology (MAASTRO), GROW School for Oncology and Developmental Biology, Maastricht University Medical Center (MUMC), Maastricht 6201 BN, The Netherlands and Instituto de Pesquisas Energéticas e Nucleares – IPEN-CNEN/SP, São Paulo CP 11049, 05422-970 (Brazil); Holt, Randy; Rusch, Thomas [Xoft, A Subsidiary of iCAD, Sunnyvale, California 94085-4115 (United States); Beaulieu, Luc [Centre Hospitalier Universitaire de Québec Université Laval, Radio-Oncologie et Centre de Recherche en Cancérologie de l’Université Laval, Québec, Québec G1R 2J6 Canada (Canada); Verhaegen, Frank [Department of Radiation Oncology (MAASTRO), GROW School for Oncology and Developmental Biology, Maastricht University Medical Center (MUMC), Maastricht 6201 BN, The Netherlands and Department of Oncology, McGill University, Montreal, Quebec H3G 1A4 (Canada)

    2014-06-15

    Purpose: The recently updated guidelines for dosimetry in brachytherapy in TG-186 have recommended the use of model-based dosimetry calculations as a replacement for TG-43. TG-186 highlights shortcomings in the water-based approach in TG-43, particularly for low energy brachytherapy sources. The Xoft Axxent is a low energy (<50 kV) brachytherapy system used in accelerated partial breast irradiation (APBI). Breast tissue is a heterogeneous tissue in terms of density and composition. Dosimetric calculations of seven APBI patients treated with Axxent were made using a model-based Monte Carlo platform for a number of tissue models and dose reporting methods and compared to TG-43 based plans. Methods: A model of the Axxent source, the S700, was created and validated against experimental data. CT scans of the patients were used to create realistic multi-tissue/heterogeneous models with breast tissue segmented using a published technique. Alternative water models were used to isolate the influence of tissue heterogeneity and backscatter on the dose distribution. Dose calculations were performed using Geant4 according to the original treatment parameters. The effect of the Axxent balloon applicator used in APBI which could not be modeled in the CT-based model, was modeled using a novel technique that utilizes CAD-based geometries. These techniques were validated experimentally. Results were calculated using two dose reporting methods, dose to water (D{sub w,m}) and dose to medium (D{sub m,m}), for the heterogeneous simulations. All results were compared against TG-43-based dose distributions and evaluated using dose ratio maps and DVH metrics. Changes in skin and PTV dose were highlighted. Results: All simulated heterogeneous models showed a reduced dose to the DVH metrics that is dependent on the method of dose reporting and patient geometry. Based on a prescription dose of 34 Gy, the average D{sub 90} to PTV was reduced by between ∼4% and ∼40%, depending on the

  16. Thermogravimetric study of a Phase Change Slurry: Effect of variable conditions

    International Nuclear Information System (INIS)

    Giro-Paloma, J.; Valle-Zermeño, R. del; Fernández, A.I.; Chimenos, J.M.; Formosa, J.

    2016-01-01

    Highlights: • Dry or wet PCS present differences in their thermal behavior. • The optimum conditions of dry PCS were determined by TGA. • Type of atmosphere and heating rate were the variables under consideration. • T peak can be accurately determined at 1 °C·min −1 in N 2. • Fusion/latent heat can be best determined at 10 °C·min −1 . - Abstract: Microcapsules containing Phase Change Materials (MPCM) are widely used for passive systems in energy storage. When MPCM are mixed with a carrier fluid, Phase Change Slurries (PCS) are used for heat transfer fluids in active systems or heat transport systems. The thermal behavior of PCS can be measured as dry or wet basis, resulting in important differences in weight losses. This study explores the optimum conditions for analyzing the thermal behavior of dried PCS by thermogravimetric analysis (TGA) varying the parameter conditions for obtaining peak temperature and heat flow (latent heat). The factors that were taken into account were the atmosphere of study (air and nitrogen) and the heating rate (0.5, 1, 5, and 10 °C·min −1 ). The best conditions to determine peak temperature are at 1 °C·min −1 and in N 2 atmosphere, whereas the decomposition fusion/latent heat of the sample is improved at higher heating velocities towards 10 °C·min −1 .

  17. Thermogravimetric study of the kinetics of lithium titanate reduction by hydrogen

    International Nuclear Information System (INIS)

    Sonak, Sagar; Rakesh, R.; Jain, Uttam; Mukherjee, Abhishek; Kumar, Sanjay; Krishnamurthy, Nagaiyar

    2014-01-01

    Highlights: • Li 2 TiO 3 powder is synthesized by the gel combustion route. • Activation energy of reduction of Li 2 TiO 3 by H 2 found out to be 27.45 kJ/mol H 2 . • Non-stoichiometric phase of Li 2 TiO 3 is formed in hydrogen atmosphere. • One-dimensional diffusion appears to be the most probable mechanism of reduction. - Abstract: The lithium titanate powder was synthesized by gel-combustion route. The mechanism and the kinetics of hydrogen interaction with lithium titanate powder were studied using non-isothermal thermogravimetric technique. Lithium titanate underwent reduction in hydrogen atmosphere which led to the formation of oxygen deficient non-stoichiometric compound in lithium titanate. One-dimensional diffusion appeared to be the most probable reaction mechanism. The activation energy for reduction of lithium titanate under hydrogen atmosphere was found to be 27.4 kJ/mol/K. Structural changes after hydrogen reduction in lithium titanate were observed in X-ray diffraction analysis

  18. Thermogravimetric-mass spectrometric study on the evolution of nitrogen compounds during coal devolatilisation

    Energy Technology Data Exchange (ETDEWEB)

    Arenillas, A.; Rubiera, F.; Pevida, C.; Pis, J.J. [Department of Energy and Environment, Instituto Nacional del Carbon, CSIC, Apartado 73, 33080 Oviedo (Spain)

    2002-10-01

    Emissions of nitrogen oxides during coal combustion are a major environmental problem. The chemically bound nitrogen in fuel accounts for up to 80% of total NO{sub x} emissions. In this respect, fundamental studies are needed to clarify the mechanisms and to identify the different species that are precursors in the formation of the NO{sub x}. Mass spectrometry (MS) has been used for decades as a successful technique in evolved gas analysis. However, MS is normally used to identify typical volatile compounds formed during coal pyrolysis (i.e. H{sub 2}, CH{sub 4}, CO, CO{sub 2} and H{sub 2}O) but very few works on the detection by MS of nitrogen compounds during coal devolatilisation can be found. In this work, the possibility of detecting different nitrogen compounds by means of thermogravimetric-MS during the temperature-programmed pyrolysis of coal was evaluated. Interferences in the N-compounds MS signals were determined. The use of model compounds provided additional information on the MS response factors of the volatile compounds produced.

  19. Thermogravimetric studies on alkyl methacrylate polymers and poly(alkyl methacrylate)-grafted polypropylene fibers

    International Nuclear Information System (INIS)

    Hayakawa, Kiyoshi; Taoda, Hiroshi; Kawase, Kaoru; Tazawa, Masato; Yamakita, Hiromi

    1986-01-01

    Thermal behavior of several kinds of poly (alkyl methacrylate) and polypropylene-g-poly (alkyl methacrylate) fibers prepared by γ-irradiation was investigated by thermogravimetric measurements with the intermittent analysis of the gaseous products. The degradation of poly (methyl methacrylate) proceeded according to the deploymerization mechanism reproducing the pristine monomer exclusively. The thermogram in inert atmosphere showed the features of a two-step depolymerization, while in air it showed no such a stepwise decrease with the elevating temperature. The dissolution-precipitation treatment of polymer seemed to affect the decomposition behavior. On other alkyl methacrylate polymers, the thermal decomposition generally proceeded also according to the depolymerization mechanism. But, for instance, at least two kinds of products besides its own monomer were formed from poly (isobutyl methacrylate), and their relative fractions differed with the temperature. Polypropylene-g-poly (alkyl methacrylate) fibers showed lowering of initiation temperature of decomposition with the increase in extent of the grafting, and their initiation temperatures of decomposition in air were lower than those in inert atmosphere. (author)

  20. Thermogravimetric investigation on the degradation properties and combustion performance of bio-oils.

    Science.gov (United States)

    Ren, Xueyong; Meng, Jiajia; Moore, Andrew M; Chang, Jianmin; Gou, Jinsheng; Park, Sunkyu

    2014-01-01

    The degradation properties and combustion performance of raw bio-oil, aged bio-oil, and bio-oil from torrefied wood were investigated through thermogravimetric analysis. A three-stage process was observed for the degradation of bio-oils, including devolatilization of the aqueous fraction and light compounds, transition of the heavy faction to solid, and combustion of carbonaceous residues. Pyrolysis kinetics parameters were calculated via the reaction order model and 3D-diffusion model, and combustion indexes were used to qualitatively evaluate the thermal profiles of tested bio-oils for comparison with commercial oils such as fuel oils. It was found that aged bio-oil was more thermally instable and produced more combustion-detrimental carbonaceous solid. Raw bio-oil and bio-oil from torrefied wood had comparable combustion performance to fuel oils. It was considered that bio-oil has a potential to be mixed with or totally replace the fuel oils in boilers. Copyright © 2013 Elsevier Ltd. All rights reserved.

  1. Thermogravimetric Studies of Deposited Potash Impregnated for Flame-Retardancy into a Cotton Fabric

    Institute of Scientific and Technical Information of China (English)

    MOSTASHARI, S.M.; NIA, Y.K.; BAIE, S.

    2007-01-01

    The effect of potash as a nondurable finish on the flammability of 100% cotton fabric (plain 180 g/m2) was investigated. The bone-dried weighed fabrics were dipped into suitable concentrations of potash, with a volume of 100 mL at 20-2 ℃. The impregnation was followed by means of squeeze rolls and drying at 110 C. The samples were then reweighed with analytical precision. After conditioning overnight by using our "vertical flame tester" the optimum add-on values to impart flame-retardancy to cotton fabric was determined and expressed by 0.80 g of potash per 100 g fabric to be an efficient addition. Thermogravimetric analysis of pure cotton, treated cotton with potash at its optimum efficiency for donation of flame-retardancy into cotton fabric was fulfilled and the thermograms were compared and commented. The effectiveness of this hydroxide was attributed to the heat dissipation by the remaining consumed material during the combustion. The results obtained are in favor of "Dust or Wall Effect Theory".

  2. Comparison of TG-43 and TG-186 in breast irradiation using a low energy electronic brachytherapy source.

    Science.gov (United States)

    White, Shane A; Landry, Guillaume; Fonseca, Gabriel Paiva; Holt, Randy; Rusch, Thomas; Beaulieu, Luc; Verhaegen, Frank; Reniers, Brigitte

    2014-06-01

    The recently updated guidelines for dosimetry in brachytherapy in TG-186 have recommended the use of model-based dosimetry calculations as a replacement for TG-43. TG-186 highlights shortcomings in the water-based approach in TG-43, particularly for low energy brachytherapy sources. The Xoft Axxent is a low energy (S700, was created and validated against experimental data. CT scans of the patients were used to create realistic multi-tissue/heterogeneous models with breast tissue segmented using a published technique. Alternative water models were used to isolate the influence of tissue heterogeneity and backscatter on the dose distribution. Dose calculations were performed using Geant4 according to the original treatment parameters. The effect of the Axxent balloon applicator used in APBI which could not be modeled in the CT-based model, was modeled using a novel technique that utilizes CAD-based geometries. These techniques were validated experimentally. Results were calculated using two dose reporting methods, dose to water (Dw,m) and dose to medium (Dm,m), for the heterogeneous simulations. All results were compared against TG-43-based dose distributions and evaluated using dose ratio maps and DVH metrics. Changes in skin and PTV dose were highlighted. All simulated heterogeneous models showed a reduced dose to the DVH metrics that is dependent on the method of dose reporting and patient geometry. Based on a prescription dose of 34 Gy, the average D90 to PTV was reduced by between ~4% and ~40%, depending on the scoring method, compared to the TG-43 result. Peak skin dose is also reduced by 10%-15% due to the absence of backscatter not accounted for in TG-43. The balloon applicator also contributed to the reduced dose. Other ROIs showed a difference depending on the method of dose reporting. TG-186-based calculations produce results that are different from TG-43 for the Axxent source. The differences depend strongly on the method of dose reporting. This study

  3. MO-PIS-Exhibit Hall-01: Tools for TG-142 Linac Imaging QA I

    Energy Technology Data Exchange (ETDEWEB)

    Clements, M [RAD Image, Colorado Springs, CO (United States); Wiesmeyer, M [Standard Imaging, Inc., Middleton, WI (United States)

    2014-06-15

    Partners in Solutions is an exciting new program in which AAPM partners with our vendors to present practical “hands-on” information about the equipment and software systems that we use in our clinics. The therapy topic this year is solutions for TG-142 recommendations for linear accelerator imaging QA. Note that the sessions are being held in a special purpose room built on the Exhibit Hall Floor, to encourage further interaction with the vendors. Automated Imaging QA for TG-142 with RIT Presentation Time: 2:45 – 3:15 PM This presentation will discuss software tools for automated imaging QA and phantom analysis for TG-142. All modalities used in radiation oncology will be discussed, including CBCT, planar kV imaging, planar MV imaging, and imaging and treatment coordinate coincidence. Vendor supplied phantoms as well as a variety of third-party phantoms will be shown, along with appropriate analyses, proper phantom setup procedures and scanning settings, and a discussion of image quality metrics. Tools for process automation will be discussed which include: RIT Cognition (machine learning for phantom image identification), RIT Cerberus (automated file system monitoring and searching), and RunQueueC (batch processing of multiple images). In addition to phantom analysis, tools for statistical tracking, trending, and reporting will be discussed. This discussion will include an introduction to statistical process control, a valuable tool in analyzing data and determining appropriate tolerances. An Introduction to TG-142 Imaging QA Using Standard Imaging Products Presentation Time: 3:15 – 3:45 PM Medical Physicists want to understand the logic behind TG-142 Imaging QA. What is often missing is a firm understanding of the connections between the EPID and OBI phantom imaging, the software “algorithms” that calculate the QA metrics, the establishment of baselines, and the analysis and interpretation of the results. The goal of our brief presentation will be to

  4. MO-PIS-Exhibit Hall-01: Tools for TG-142 Linac Imaging QA I

    International Nuclear Information System (INIS)

    Clements, M; Wiesmeyer, M

    2014-01-01

    Partners in Solutions is an exciting new program in which AAPM partners with our vendors to present practical “hands-on” information about the equipment and software systems that we use in our clinics. The therapy topic this year is solutions for TG-142 recommendations for linear accelerator imaging QA. Note that the sessions are being held in a special purpose room built on the Exhibit Hall Floor, to encourage further interaction with the vendors. Automated Imaging QA for TG-142 with RIT Presentation Time: 2:45 – 3:15 PM This presentation will discuss software tools for automated imaging QA and phantom analysis for TG-142. All modalities used in radiation oncology will be discussed, including CBCT, planar kV imaging, planar MV imaging, and imaging and treatment coordinate coincidence. Vendor supplied phantoms as well as a variety of third-party phantoms will be shown, along with appropriate analyses, proper phantom setup procedures and scanning settings, and a discussion of image quality metrics. Tools for process automation will be discussed which include: RIT Cognition (machine learning for phantom image identification), RIT Cerberus (automated file system monitoring and searching), and RunQueueC (batch processing of multiple images). In addition to phantom analysis, tools for statistical tracking, trending, and reporting will be discussed. This discussion will include an introduction to statistical process control, a valuable tool in analyzing data and determining appropriate tolerances. An Introduction to TG-142 Imaging QA Using Standard Imaging Products Presentation Time: 3:15 – 3:45 PM Medical Physicists want to understand the logic behind TG-142 Imaging QA. What is often missing is a firm understanding of the connections between the EPID and OBI phantom imaging, the software “algorithms” that calculate the QA metrics, the establishment of baselines, and the analysis and interpretation of the results. The goal of our brief presentation will be to

  5. Effect of superfine grinding on the physico-chemical, morphological and thermogravimetric properties of Lentinus edodes mushroom powders.

    Science.gov (United States)

    Ming, Jian; Chen, Long; Hong, Hui; Li, Jinlong

    2015-09-01

    Lentinus edodes is an edible mushroom commonly known as shiitake, which is the second most produced and consumed edible mushroom in the world and is an important nutrient source in the human diet. To fully use L. edodes, the mushrooms are occasionally ground into powder as a flavourful and functional food additive. This study produces powders from the cap and stipe of Lentinus edodes mushrooms through superfine grinding. These powders are composed of sub-micron range particles with various size distributions. The superfine grinding process is then compared with shear pulverisation to determine the different effects on both the cap and stipe powders in terms of particle size and physico-chemical, morphological and thermogravimetric properties. When average particle size was reduced to 0.54 and 0.46 µm, respectively, the moisture and protein content, angles of repose and slide, and water holding capacity of the powders decreased to varied extents. However, soluble dietary fibre, water solubility index, and swelling capacity increased. Scanning electron microscope images suggested that the superfine grinding process effectively changed the original surface structure of the L. edodes powders. The curves of thermogravimetric analysis and those of the derivatives of thermogravimetry indicated that superfine grinding can improve the thermostability of L. edodes powders. Furthermore, superfinely ground L. edodes powders may be used as pharmaceutical or food additives in various fields. The present study suggests that superfinely ground L. edodes powders may be applied in various fields as pharmaceutical or food additives. © 2014 Society of Chemical Industry.

  6. Interpretation of Quasi-Isothermal Thermogravimetric Weight Curves

    DEFF Research Database (Denmark)

    Sørensen, Ole Toft

    1979-01-01

    Quasi-isothermal analysis (QIA) is a very useful technique. Compared to conventional non-isothermal thermogravimetry, close-lying reactions can easily be separated by use of this method and kinetic data can be obtained for each intermediate reaction in a single run. This paper discusses the shape...

  7. Dominant thermogravimetric signatures of lignin in cashew shell as compared to cashew shell cake.

    Science.gov (United States)

    Gangil, Sandip

    2014-03-01

    Dominant thermogravimetric signatures related to lignin were observed in cashew shell as compared to these signatures in cashew shell cake. The phenomenon of weakening of lignin from cashew shell to cashew shell cake was explained on the basis of changes in the activation energies. The pertinent temperature regimes responsible for the release of different constituents of both the bio-materials were identified and compared. The activation energies of cashew shell and cashew shell cake were compared using Kissinger-Akahira-Sunose method. Thermogravimetric profiling of cashew shell and cashew shell cake indicated that these were different kinds of bio-materials. Copyright © 2013 Elsevier Ltd. All rights reserved.

  8. In vivo determination of triglyceride (TG) secretion in rats fed different dietary saturated fats using [2-3H]-glycerol

    International Nuclear Information System (INIS)

    Lai, H.C.; Yang, H.; Lasekan, J.; Clayton, M.; Ney, D.M.

    1990-01-01

    Male, Sprague-Dawley rats (154±1 g) were fed diets containing 2% corn oil (CO) + 14% butterfat (BF), beef tallow (BT), olive oil (OO) or coconut oil (CN) vs a 16% CO control diet for 5 weeks. Changes in plasma TG specific activity (dpm/mg TG) were determined in individual unanesthetized rats after injection of 100 μCi [2- 3 H]-glycerol via a carotid cannula. Fractional rate constants were obtained using a 2-compartment model and nonlinear regression analysis. Results demonstrated no difference in the fractional rate constants among dietary groups; but, differences in the rates of hepatic TG secretion were noted. Rats fed BT showed a higher rate of hepatic TG secretion than rats fed CO. Rats fed BF, OO or CN showed somewhat higher rates of hepatic TG secretion than CO. VLDL TG, phospholipid, and apolipoprotein B and E levels were higher with saturated fats vs CO. The data suggest that the higher plasma TG levels noted in response to feeding saturated fats vs corn oil can be explained, in part, by an increased flux of hepatic TG secretion

  9. WE-PIS-Exhibit Hall-01: Tools for TG-142 Linac Imaging QA II

    International Nuclear Information System (INIS)

    Childress, N; Murray, B

    2014-01-01

    Partners in Solutions is an exciting new program in which AAPM partners with our vendors to present practical “hands-on” information about the equipment and software systems that we use in our clinics. The therapy topic this year is solutions for TG-142 recommendations for linear accelerator imaging QA. Note that the sessions are being held in a special purpose room built on the Exhibit Hall Floor, to encourage further interaction with the vendors. Using DoseLab to Perform TG-142 Imaging QA The goals of this session will be to present a clinical overview of acquiring images for TG-142 Imaging QA, as well as analyzing and evaluating results using DoseLab software. DoseLab supports planar imaging QA analysis using almost any QA phantom provided by numerous vendors. General advantages and disadvantages of selecting each of these phantoms will be briefly summarized. Best practices for selecting image acquisition parameters will be presented. A demonstration of using DoseLab software to perform a series of TG-142 tests will be performed. We will disuss why DoseLab uses its own set of imaging QA formulas, and why imaging QA measurement values of the same nominal properties will vary between TG- 142 software packages. Because TG-142 does not specify baseline and tolerance values for imaging QA, the presentation will recommend performing the manufacturer's acceptance test procedure to validate the equipment is functioning correctly. Afterwards, results can be obtained using the clinic's selected set of phantoms, image acquisition parameters, and TG-142 software to set proper baseline values. This presentation will highlight the reasons why comparing imaging QA results can be trickier than comparing linear accelerator treatment results and what physicists should keep in mind when comparing imaging QA results for different machines. Physicists are often unsure of the next step when there is an issue discovered during Imaging QA. Therefore, a few common examples

  10. WE-PIS-Exhibit Hall-01: Tools for TG-142 Linac Imaging QA II

    Energy Technology Data Exchange (ETDEWEB)

    Childress, N [Mobius Medical Management, LLC,, Houston, TX (United States); Murray, B [ZapIT Medical, Dublin, OH (Ireland)

    2014-06-15

    Partners in Solutions is an exciting new program in which AAPM partners with our vendors to present practical “hands-on” information about the equipment and software systems that we use in our clinics. The therapy topic this year is solutions for TG-142 recommendations for linear accelerator imaging QA. Note that the sessions are being held in a special purpose room built on the Exhibit Hall Floor, to encourage further interaction with the vendors. Using DoseLab to Perform TG-142 Imaging QA The goals of this session will be to present a clinical overview of acquiring images for TG-142 Imaging QA, as well as analyzing and evaluating results using DoseLab software. DoseLab supports planar imaging QA analysis using almost any QA phantom provided by numerous vendors. General advantages and disadvantages of selecting each of these phantoms will be briefly summarized. Best practices for selecting image acquisition parameters will be presented. A demonstration of using DoseLab software to perform a series of TG-142 tests will be performed. We will disuss why DoseLab uses its own set of imaging QA formulas, and why imaging QA measurement values of the same nominal properties will vary between TG- 142 software packages. Because TG-142 does not specify baseline and tolerance values for imaging QA, the presentation will recommend performing the manufacturer's acceptance test procedure to validate the equipment is functioning correctly. Afterwards, results can be obtained using the clinic's selected set of phantoms, image acquisition parameters, and TG-142 software to set proper baseline values. This presentation will highlight the reasons why comparing imaging QA results can be trickier than comparing linear accelerator treatment results and what physicists should keep in mind when comparing imaging QA results for different machines. Physicists are often unsure of the next step when there is an issue discovered during Imaging QA. Therefore, a few common examples

  11. TgICMAP1 is a novel microtubule binding protein in Toxoplasma gondii.

    Directory of Open Access Journals (Sweden)

    Aoife T Heaslip

    Full Text Available The microtubule cytoskeleton provides essential structural support for all eukaryotic cells and can be assembled into various higher order structures that perform drastically different functions. Understanding how microtubule-containing assemblies are built in a spatially and temporally controlled manner is therefore fundamental to understanding cell physiology. Toxoplasma gondii, a protozoan parasite, contains at least five distinct tubulin-containing structures, the spindle pole, centrioles, cortical microtubules, the conoid, and the intra-conoid microtubules. How these five structurally and functionally distinct sets of tubulin containing structures are constructed and maintained in the same cell is an intriguing problem. Previously, we performed a proteomic analysis of the T. gondii apical complex, a cytoskeletal complex located at the apical end of the parasite that is composed of the conoid, three ring-like structures, and the two short intra-conoid microtubules. Here we report the characterization of one of the proteins identified in that analysis, TgICMAP1. We show that TgICMAP1 is a novel microtubule binding protein that can directly bind to microtubules in vitro and stabilizes microtubules when ectopically expressed in mammalian cells. Interestingly, in T. gondii, TgICMAP1 preferentially binds to the intra-conoid microtubules, providing us the first molecular tool to investigate the intra-conoid microtubule assembly process during daughter construction.

  12. Thermogravimetric, Devolatilization Rate, and Differential Scanning Calorimetry Analyses of Biomass of Tropical Plantation Species of Costa Rica Torrefied at Different Temperatures and Times

    Directory of Open Access Journals (Sweden)

    Johanna Gaitán-Álvarez

    2018-03-01

    Full Text Available We evaluated the thermogravimetric and devolatilization rates of hemicellulose and cellulose, and the calorimetric behavior of the torrefied biomass, of five tropical woody species (Cupressus lusitanica, Dipteryx panamensis, Gmelina arborea, Tectona grandis and Vochysia ferruginea, at three temperatures (TT and three torrefaction times (tT using a thermogravimetric analyzer. Through a multivariate analysis of principal components (MAPC, the most appropriate torrefaction conditions for the different types of woody biomass were identified. The thermogravimetric analysis-derivative thermogravimetry (TGA-DTG analysis showed that a higher percentage of the hemicellulose component of the biomass degrades, followed by cellulose, so that the hemicellulose energy of activation (Ea was less than that of cellulose. With an increase in TT and tT, the Ea for hemicellulose decreased but increased for cellulose. The calorimetric analyses showed that hemicellulose is the least stable component in the torrefied biomass under severe torrefaction conditions, and cellulose is more thermally stable in torrefied biomass. From the MAPC results, the best torrefaction conditions for calorimetric analyses were at 200 and 225 °C after 8, 10, and 12 min, for light and middle torrefaction, respectively, for the five woody species.

  13. Chemical and Pyrolytic Thermogravimetric Characterization of Nigerian Bituminous Coals

    Directory of Open Access Journals (Sweden)

    Nyakuma Bemgba Bevan

    2016-12-01

    Full Text Available The discovery of new coal deposits in Nigeria presents solutions for nation’s energy crises and prospects for socioeconomic growth and sustainable development. Furthermore, the quest for sustainable energy to limit global warming, climate change, and environmental degradation has necessitated the exploration of alternatives using cleaner technologies such as coal pyrolysis. However, a lack of comprehensive data on physico-chemical and thermal properties of Nigerian coals has greatly limited their utilization. Therefore, the physico-chemical properties, rank (classification, and thermal decomposition profiles of two Nigerian bituminous coals – Afuze (AFZ and Shankodi-Jangwa (SKJ – were examined in this study. The results indicate that the coals contain high proportions of C, H, N, S, O and a sufficiently high heating value (HHV for energy conversion. The coal classification revealed that the Afuze (AFZ coal possesses a higher rank, maturity, and coal properties compared to the Shankodi-Jangwa (SKJ coal. A thermal analysis demonstrated that coal pyrolysis in both cases occurred in three stages; drying (30-200 °C, devolatilization (200-600 °C, and char decomposition (600-1000 °C. The results also indicated that pyrolysis at 1000 °C is not sufficient for complete pyrolysis. In general, the thermochemical and pyrolytic fuel properties indicate that the coal from both places can potentially be utilized for future clean energy applications.

  14. Thermogravimetric and nuclear magnetic resonance study of hydrated Na-β''-alumina

    International Nuclear Information System (INIS)

    Donoso, P.; Panepucci, H.; Gobato, Y.G.; Oliveira, L.N.; Souza, D.P.F. de

    1990-01-01

    This paper reports thermogravimetric and proton spin-lattice relaxation times measurement of hydrated Na-β''-alumina, which yield information about the identification of the sites where the loosely bound water molecules are located in the polycrystalline sample. It examines also the influence of impurities on the motion of the protons. (autor) [pt

  15. Co-combustion characteristics and blending optimization of tobacco stem and high-sulfur bituminous coal based on thermogravimetric and mass spectrometry analyses.

    Science.gov (United States)

    Zhang, Kaihua; Zhang, Kai; Cao, Yan; Pan, Wei-ping

    2013-03-01

    Despite much research on co-combustion of tobacco stem and high-sulfur coal, their blending optimization has not been effectively found. This study investigated the combustion profiles of tobacco stem, high-sulfur bituminous coal and their blends by thermogravimetric analysis. Ignition and burnout performances, heat release performances, and gaseous pollutant emissions were also studied by thermogravimetric and mass spectrometry analyses. The results indicated that combustion of tobacco stem was more complicated than that of high-sulfur bituminous coal, mainly shown as fixed carbon in it was divided into two portions with one early burning and the other delay burning. Ignition and burnout performances, heat release performances, and gaseous pollutant emissions of the blends present variable trends with the increase of tobacco stem content. Taking into account the above three factors, a blending ratio of 0–20% tobacco stem content is conservatively proposed as optimum amount for blending. Copyright © 2012 Elsevier Ltd. All rights reserved.

  16. Thermogravimetric characteristics and kinetics of scrap tyre and Juglans regia shell co-pyrolysis.

    Science.gov (United States)

    Uzun, B B; Yaman, E

    2014-10-01

    The degradation kinetics of Juglans regia shell, scrap tyre and their blends were investigated using a thermogravimetric analysis method. Experiments were performed under dynamic conditions and a nitrogen atmosphere in the range 293 to 973 K at different heating rates. During pyrolysis of J. regia shell three mass loss zones were specified as removal of water, decomposition of hemicelluloses and cellulose, and decomposition of lignin. The degradation curves of scrap tyre showed merely one stage which was due to decomposition of styrene butadiene rubber. The kinetic parameters were calculated using both Arrhenius and Coats-Redfern methods. By adopting the Arrhenius method, the average value of activation energies of J. regia shell, scrap tyre and their 1 : 1 blends were found to be 69.22, 71.48 and 47.03 kJ mol(-1), respectively. Additionally, by using the Coats-Redfern method, the average value of activation energies of J. regia shell, scrap tyre and their 1 : 1 blend were determined as 99.85, 78.72 and 63.81 kJ mol(-1), respectively. The addition of J. regia shell to scrap tyre caused a reduction in the activation energies. The difference of weight loss was measured to examine interactions between raw materials. The maximum difference between experimental and theoretical mass loss was 5% at about 648 K with a heating rate of 20 K min(-1). These results indicated a significant synergistic effect was available during co-pyrolysis of J. regia shell and scrap tyre in the high temperature region. © The Author(s) 2014.

  17. Report of AAPM TG 135: quality assurance for robotic radiosurgery.

    Science.gov (United States)

    Dieterich, Sonja; Cavedon, Carlo; Chuang, Cynthia F; Cohen, Alan B; Garrett, Jeffrey A; Lee, Charles L; Lowenstein, Jessica R; d'Souza, Maximian F; Taylor, David D; Wu, Xiaodong; Yu, Cheng

    2011-06-01

    The task group (TG) for quality assurance for robotic radiosurgery was formed by the American Association of Physicists in Medicine's Science Council under the direction of the Radiation Therapy Committee and the Quality Assurance (QA) Subcommittee. The task group (TG-135) had three main charges: (1) To make recommendations on a code of practice for Robotic Radiosurgery QA; (2) To make recommendations on quality assurance and dosimetric verification techniques, especially in regard to real-time respiratory motion tracking software; (3) To make recommendations on issues which require further research and development. This report provides a general functional overview of the only clinically implemented robotic radiosurgery device, the CyberKnife. This report includes sections on device components and their individual component QA recommendations, followed by a section on the QA requirements for integrated systems. Examples of checklists for daily, monthly, annual, and upgrade QA are given as guidance for medical physicists. Areas in which QA procedures are still under development are discussed.

  18. TH-A-BRC-01: AAPM TG-135U1 QA for Robotic Radiosurgery

    International Nuclear Information System (INIS)

    Dieterich, S.

    2016-01-01

    of possible dosimetry protocols. The report will be reviewed by the AAPM Working Group on Recommendations for Radiotherapy External Beam Quality Assurance and then by the AAPM Science Council before publication in Medical Physics Survey of possible calibration protocols for calibration of Gamma Stereotactic Radiosurgery (GSR) devices Overview of modern Quality Assurance techniques for GSR AAPM TG-218 Tolerance Levels and Methodologies for IMRT Verification QA - Moyed Miften Patient-specific IMRT QA measurement is a process designed to identify discrepancies between calculated and delivered doses. Error tolerance limits are not well-defined or consistently applied across centers. The AAPM TG-218 report has been prepared to improve the understanding and consistency of this process by providing recommendations for methodologies and tolerance limits in patient-specific IMRT QA. Learning Objectives: Review measurement methods and methodologies for absolute dose verification Provide recommendations on delivery methods, data interpretation, the use of analysis routines and choice of tolerance limits for IMRT QA Sonja Dieterich has a research agreement with Sun Nuclear Inc. Steven Goetsch is a part-time consultant for Elekta.

  19. TH-A-BRC-01: AAPM TG-135U1 QA for Robotic Radiosurgery

    Energy Technology Data Exchange (ETDEWEB)

    Dieterich, S. [UC Davis Medical Center (United States)

    2016-06-15

    of possible dosimetry protocols. The report will be reviewed by the AAPM Working Group on Recommendations for Radiotherapy External Beam Quality Assurance and then by the AAPM Science Council before publication in Medical Physics Survey of possible calibration protocols for calibration of Gamma Stereotactic Radiosurgery (GSR) devices Overview of modern Quality Assurance techniques for GSR AAPM TG-218 Tolerance Levels and Methodologies for IMRT Verification QA - Moyed Miften Patient-specific IMRT QA measurement is a process designed to identify discrepancies between calculated and delivered doses. Error tolerance limits are not well-defined or consistently applied across centers. The AAPM TG-218 report has been prepared to improve the understanding and consistency of this process by providing recommendations for methodologies and tolerance limits in patient-specific IMRT QA. Learning Objectives: Review measurement methods and methodologies for absolute dose verification Provide recommendations on delivery methods, data interpretation, the use of analysis routines and choice of tolerance limits for IMRT QA Sonja Dieterich has a research agreement with Sun Nuclear Inc. Steven Goetsch is a part-time consultant for Elekta.

  20. TH-A-BRC-02: AAPM TG-178 Gamma Stereotactic Radiosurgery Dosimetry and Quality Assurance

    Energy Technology Data Exchange (ETDEWEB)

    Goetsch, S. [San Diego Medical Physics (United States)

    2016-06-15

    of possible dosimetry protocols. The report will be reviewed by the AAPM Working Group on Recommendations for Radiotherapy External Beam Quality Assurance and then by the AAPM Science Council before publication in Medical Physics Survey of possible calibration protocols for calibration of Gamma Stereotactic Radiosurgery (GSR) devices Overview of modern Quality Assurance techniques for GSR AAPM TG-218 Tolerance Levels and Methodologies for IMRT Verification QA - Moyed Miften Patient-specific IMRT QA measurement is a process designed to identify discrepancies between calculated and delivered doses. Error tolerance limits are not well-defined or consistently applied across centers. The AAPM TG-218 report has been prepared to improve the understanding and consistency of this process by providing recommendations for methodologies and tolerance limits in patient-specific IMRT QA. Learning Objectives: Review measurement methods and methodologies for absolute dose verification Provide recommendations on delivery methods, data interpretation, the use of analysis routines and choice of tolerance limits for IMRT QA Sonja Dieterich has a research agreement with Sun Nuclear Inc. Steven Goetsch is a part-time consultant for Elekta.

  1. TH-A-BRC-02: AAPM TG-178 Gamma Stereotactic Radiosurgery Dosimetry and Quality Assurance

    International Nuclear Information System (INIS)

    Goetsch, S.

    2016-01-01

    of possible dosimetry protocols. The report will be reviewed by the AAPM Working Group on Recommendations for Radiotherapy External Beam Quality Assurance and then by the AAPM Science Council before publication in Medical Physics Survey of possible calibration protocols for calibration of Gamma Stereotactic Radiosurgery (GSR) devices Overview of modern Quality Assurance techniques for GSR AAPM TG-218 Tolerance Levels and Methodologies for IMRT Verification QA - Moyed Miften Patient-specific IMRT QA measurement is a process designed to identify discrepancies between calculated and delivered doses. Error tolerance limits are not well-defined or consistently applied across centers. The AAPM TG-218 report has been prepared to improve the understanding and consistency of this process by providing recommendations for methodologies and tolerance limits in patient-specific IMRT QA. Learning Objectives: Review measurement methods and methodologies for absolute dose verification Provide recommendations on delivery methods, data interpretation, the use of analysis routines and choice of tolerance limits for IMRT QA Sonja Dieterich has a research agreement with Sun Nuclear Inc. Steven Goetsch is a part-time consultant for Elekta.

  2. Thermogravimetric and Differential Scanning Calorimetric Behavior of Ball-Milled Nuclear Graphite

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Eung Seon; Kim, Min Hwan; Kim, Yong Wan [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Park, Yi Hyun; Cho, Seung Yon [National Fusion Research Institute, Daejeon (Korea, Republic of)

    2013-10-15

    An examination was made to characterize the oxidation behavior of ball-milled nuclear graphite powder through a TG-DSC analysis. With the ball milling time, the BET surface area increased with the reduction of particle size, but decreased with the chemisorptions of O{sub 2} on the activated surface. The enhancement of the oxidation after the ball milling is attributed to both increases in the specific surface area and atomic scale defects in the graphite structure. In a high temperature gas-cooled reactor, nuclear graphite has been widely used as fuel elements, moderator or reflector blocks, and core support structures owing to its excellent moderating power, mechanical properties and machinability. For the same reason, it will be used in a helium cooled ceramic reflector test blanket module for the ITER. Each submodule has a seven-layer breeding zone, including three neutron multiplier layers packed with beryllium pebbles, three lithium ceramic pebbles packed tritium breeder layers, and a reflector layer packed with 1 mm diameter graphite pebbles to reduce the volume of beryllium. The abrasion of graphite structures owing to relative motion or thermal cycle during operation may produce graphite dust. It is expected that graphite dust will be more oxidative than bulk graphite, and thus the oxidation behavior of graphite dust must be examined to analyze the safety of the reactors during an air ingress accident. In this study, the thermal stability of ball-milled graphite powder was investigated using a simultaneous thermogravimeter-differential scanning calorimeter.

  3. TG-FTIR measurement of CO2-H2O co-adsorption for CO2 air capture sorbent screening

    NARCIS (Netherlands)

    Smal, I.M.; Yu, Qian; Veneman, Rens; Fränzel-Luiten, B.; Brilman, Derk Willem Frederik

    2014-01-01

    Capturing atmospheric CO2 using solid sorbents is gaining interest. As ambient air normally contains much more (up to 100 times) water than CO2, a selective sorbent is desirable as co-adsorption will most likely occur. In this study, a convenient method based on an TG-FTIR analysis system is

  4. Sedimentation technique of waste bituminization and thermogravimetric characteristics of the final products

    Energy Technology Data Exchange (ETDEWEB)

    Zeger, J; Knotik, K; Jakusch, H

    1976-01-01

    In the research centre of the Oesterreichische Studiengesellschaft fuer Atomenergie GesmbH a semitechnical plant has been installed for waste bituminization, which has been tested inactively since 1973. This plant is using a new technological process for embedding. One of the important features of this new process is that the, normally inactive solution water is distilled off prior to the embedding, resulting in dry and powdery salts. The second important feature is that the mixing of these dry salts with the thin fluid bitumen is done by sedimentation. Expecially there is no mechanical aid used for mixing. Thermogravimetric analysis of samples which simulated the final products of this pilot plant, were carried out to verify the best working parameters and to study the possible chemical damage to the bitumen. Analysis was performed by heating the samples, consisting of various mixtures of bitumen and inorganic salts, in a METTLER-Thermoanalyzer up to 500/sup 0/C using different atmospheres (air, nitrogen). It could be shown that only nitrate and nitrite especially in combination with Fe(III)-ions are of negative influence on the thermostability of bitumen. They lead to a sudden and quick weight loss of the samples between 370 and 410/sup 0/C (above the melting point of both NaNO/sub 2/ and NaNO/sub 3/). The Fe-ions hava a catalytic influence, as it could be shown that 1 1% addiation of Fe(NO/sub 3/)/sub 3/ to NaNO/sub 3/ leads to a considerable acceleration of the incineration. This influence of the Fe(III)-ion can be suppressed to some extend by a hydrolysis prior to the embedding. In preparation of further studies concerning the behaviour of radiation damaged bitumen there has been developed a method of measuring the dose rate of an unknown radioactive salt mixture at any point of this mixture. This is done by making two measurements with glass dosimeters. One with a beta-absorber to get a pure gamma-dose and the other without it to get the combined beta and

  5. Sedimentation technique of waste bituminization and thermogravimetric characteristics of the finalproducts

    International Nuclear Information System (INIS)

    Zeger, J.; Knotik, K.

    1976-01-01

    In the research centre of the Oesterreichische Studiengesellschaft fuer Atomenergie GesmbH a semitechnical plant has been installed for waste bituminization, which has been tested inactively since 1973. This plant is using a new technological process for embedding. One of the important features of this new process is that the, normally inactive solution water is distilled off prior to the embedding, resulting in dry and powdery salts. The second important feature is that the mixing of these dry salts with the thin fluid bitumen is done by sedimentation. Expecially there is no mechanical aid used for mixing. Thermogravimetric analysis of samples which simulated the final products of this pilot plant, were carried out to verify the best working parameters and to study the possible chemical damage to the bitumen. Analysis was performed by heating the samples, consisting of various mixtures of bitumen and inorganic salts, in a METTLER-Thermoanalyzer up to 500 0 C using different atmospheres (air, nitrogen). It could be shown that only nitrate and nitrite especially in combination with Fe(III)-ions are of negative influence on the thermostability of bitumen. They lead to a sudden and quick weight loss of the samples between 370 and 410 0 C (above the melting point of both NaNO 2 and NaNO 3 ). The Fe-ions hava a catalytic influence, as it could be shown that 1 1% addiation of Fe(NO 3 ) 3 to NaNO 3 leads to a considerable acceleration of the incineration. This influence of the Fe(III)-ion can be suppressed to some extend by a hydrolysis prior to the embedding. In preparation of further studies concerning the behaviour of radiation damaged bitumen there has been developed a method of measuring the dose rate of an unknown radioactive salt mixture at any point of this mixture. This is done by making two measurements with glass dosimeters. One with a beta-absorber to get a pure gamma-dose and the other without it to get the combined beta and gamma dose. (author)

  6. Long term aging of selenide glasses: evidence of sub-Tg endotherms and pre-Tg exotherms

    Science.gov (United States)

    Chen, Ping; Boolchand, P.; Georgiev, D. G.

    2010-02-01

    Long term aging, extending from months to several years, is studied on several families of chalcogenide glasses including the Ge-Se, As-Se, and Ge-As-Se systems. Special attention is given to the As-Se binary, a system that displays a rich variety of aging behavior intimately tied to sample synthesis conditions and the ambient environment in which samples are aged. Calorimetric (modulated DSC) and Raman scattering experiments are undertaken. Our results show all samples display a sub-Tg endotherm typically 10-70 °C below Tg in glassy networks possessing a mean coordination number r in the 2.25 < r < 2.45 range. Two sets of AsxSe100-x samples aged for eight years were compared, set A consisted of slow cooled samples aged in the dark, and set B consisted of melt-quenched samples aged at laboratory environment. Samples of set B in the As concentration range, 35% < x < 60%, display a pre-Tg exotherm, but the feature is not observed in samples of set A. The aging behavior of set A presumably represents intrinsic aging in these glasses, while that of set B is extrinsic due to the presence of light. The reversibility window persists in both sets of samples, but is less well defined in set B. These findings contrast with a recent study by Golovchak et al (2008 Phys. Rev. B 78 014202), which finds the onset of the reversibility window moved up to the stoichiometric composition (x = 40%). Here we show that the up-shifted window is better understood as resulting due to demixing of As4Se4 and As4Se3 molecules from the backbone, i.e., nanoscale phase separation (NSPS). We attribute sub-Tg endotherms to compaction of the flexible part of the networks upon long term aging, while the pre-Tg exotherm is to NSPS. The narrowing and sharpening of the reversibility window upon aging is interpreted as the slow 'self-organizing' stress relaxation of the phases just outside the intermediate phase, which itself is stress free and displays little aging.

  7. A novel Toxoplasma gondii nuclear factor TgNF3 is a dynamic chromatin-associated component, modulator of nucleolar architecture and parasite virulence.

    Directory of Open Access Journals (Sweden)

    Alejandro Olguin-Lamas

    2011-03-01

    Full Text Available In Toxoplasma gondii, cis-acting elements present in promoter sequences of genes that are stage-specifically regulated have been described. However, the nuclear factors that bind to these cis-acting elements and regulate promoter activities have not been identified. In the present study, we performed affinity purification, followed by proteomic analysis, to identify nuclear factors that bind to a stage-specific promoter in T. gondii. This led to the identification of several nuclear factors in T. gondii including a novel factor, designated herein as TgNF3. The N-terminal domain of TgNF3 shares similarities with the N-terminus of yeast nuclear FK506-binding protein (FKBP, known as a histone chaperone regulating gene silencing. Using anti-TgNF3 antibodies, HA-FLAG and YFP-tagged TgNF3, we show that TgNF3 is predominantly a parasite nucleolar, chromatin-associated protein that binds specifically to T. gondii gene promoters in vivo. Genome-wide analysis using chromatin immunoprecipitation followed by high-throughput sequencing (ChIP-seq identified promoter occupancies by TgNF3. In addition, TgNF3 has a direct role in transcriptional control of genes involved in parasite metabolism, transcription and translation. The ectopic expression of TgNF3 in the tachyzoites revealed dynamic changes in the size of the nucleolus, leading to a severe attenuation of virulence in vivo. We demonstrate that TgNF3 physically interacts with H3, H4 and H2A/H2B assembled into bona fide core and nucleosome-associated histones. Furthermore, TgNF3 interacts specifically to histones in the context of stage-specific gene silencing of a promoter that lacks active epigenetic acetylated histone marks. In contrast to virulent tachyzoites, which express the majority of TgNF3 in the nucleolus, the protein is exclusively located in the cytoplasm of the avirulent bradyzoites. We propose a model where TgNF3 acts essentially to coordinate nucleolus and nuclear functions by modulating

  8. Thermogravimetric study of superconducting YBa2Cu3O9-x in hydrogen

    International Nuclear Information System (INIS)

    Swaminathan, K.; Janaki, J.; Rao, G.V.N.; Sreedharan, O.M.; Radhakrishnan, T.S.

    1988-01-01

    The thermogravimetric curve of YBa 2 Cu 3 O 9-x in hydrogen exhibits five steps, the first two corresponding to the reduction of copper oxide to copper by about 683 K (as identified by XRD on quenched samples) followed by three more steps predominantly due to hydration-dehydration behaviour of BaO. The need for blank corrections and the choice of 1223 K as the temperature for the determination of oxygen stoichiometry are discussed. 6 refs.; 2 figs.; 1 table

  9. Synthesis, characterization and thermogravimetric study of zinc and cadmium acetates-polyaniline hybrids

    International Nuclear Information System (INIS)

    Fernandes de Farias, Robson

    2004-01-01

    By dissolution of respective acetates and conducting polymer in dimethylformamide, homogeneous zinc acetate and cadmium acetate-polyaniline (PANI) hybrids were synthesized and characterized by infrared spectroscopy, thermogravimetry and SEM microscopy. The infrared spectra suggests that there are interactions between PANI and the metal cations involving both, imine and amine nitrogens in a typical Lewis acid-base reaction. The thermogravimetric degradation profile of the synthesized hybrids resembles those exhibited by PANI samples

  10. Modified thermogravimetric apparatus to measure magnetic susceptibility on-line during annealing of metastable ferromagnetic materials

    International Nuclear Information System (INIS)

    Luciani, G.; Constantini, A.; Branda, F.; Ausanio, G.; Hison, C.; Iannotti, V.; Luponio, C.; Lanotte, L.

    2004-01-01

    The insertion of proper coils to generate a magnetic field, with controlled gradient, in a standard thermogravimetric apparatus is shown to be a valid solution to measure on-line, upon heat treatment, the magnetic susceptibility in ribbon shaped samples of a metastable ferromagnetic material. The method is very useful to individuate the annealing conditions that optimise soft or hard magnetic properties without using separate apparatuses for heat treatment, control of the structural phase transition and characterization of magnetic susceptibility

  11. Effect of heating rate on thermal cracking characteristics and kinetics of Xinjiang oil sand bitumen by TG-FTIR

    Science.gov (United States)

    Hao, Junhui; Zhang, Jinhong; Qiao, Yingyun; Tian, Yuanyu

    2017-08-01

    This work was aimed to investigate effects of heating rate on thermal cracking behaviors, distribution of gaseous products and activation energy of the thermal cracking process of Xinjiang oil sand bitumen (OSB). The thermal cracking experiments of Xinjiang OSB were performed by using thermogravimetric analyzer (TGA) at various heating rates of 10, 20, 50, 80 and 120 K/min. The evolving characteristic of gaseous products produced from the thermal cracking process was evaluated by the Fourier transform infrared spectrometry (FTIR) connected with TG. The kinetic parameters of the thermal cracking process of Xinjiang OSB at each of heating rate were determined by the Coats-Redfern model. The result show that the temperature intervals of DE volatilization stage and main reaction stage, the ((dw/dt) max and Tmax in thermal cracking process of Xinjiang OSB all increased with the increasing heating rate. While the heating rate has not obvious effect on the coke yield of Xinjiang OSB. Furthermore, the maximum absorbance of gaseous products and corresponding temperature became larger as the heating rate increases. The activation energy of this two stage both presented increasing trend with the rising heating rate, while the increasing content of that of DE volatilization stage was weaker compared to that of main reaction stage.

  12. AIR QUALITY IN THE CITY OF TG JIU

    Directory of Open Access Journals (Sweden)

    Adina TĂTAR

    2014-05-01

    Full Text Available One of the most important problems of the modern age is the air pollution. Within this work I realized a description of Tgjiu City: geographic location, climate, hydrographical network, variations in temperature, terrain, sources of pollution. On the basis of registered values for the air quality indicator, sedimentable powders, and interpretation of results on the basis of the provisions of the standards in force, the comments were made in relation to particulate air pollution in the city area of sedimentableTg Jiu, identifying the polluters in the area, the proposed solutions for the reduction of pollution.

  13. Sedimentation technique of waste bituminization and thermogravimetric characteristics of the final products

    International Nuclear Information System (INIS)

    Zeger, J.; Knotik, K.; Jakusch, H.

    1976-01-01

    In the research centre of the Oesterreichische Studiengesellschaft fuer Atomenergie GmbH a semi-technical plant has been installed for waste bituminization, which has been tested inactively since 1973. This plant uses a new technological process for embedding. One of the important features of this new process is that the solution water, which is normally inactive, is distilled off before embedding, resulting in dry and powdery salts. The second important feature is that these dry salts are mixed with the thin fluid bitumen by sedimentation. A special feature is that there is no mechanical aid used for mixing. Thermogravimetric analysis of samples which simulated the final products of this pilot plant was carried out to verify the best working parameters and to study the possible chemical damage to the bitumen. It was shown that only nitrate and nitrite, especially in combination with Fe(III)-ions, are of negative influence on the thermostability of bitumen. They lead to a sudden and quick weight loss of the samples between 370 and 410 0 C (above the melting point of both NaNO 2 and NaNO 3 ). The Fe-ions have a catalytic influence, as it could be shown that a 1% addition of Fe(NO 3 ) 3 to NaNO 3 leads to a considerable acceleration of the incineration. This influence of the Fe(III)-ion can be suppressed to some extent by a hydrolysis before the embedding. There is, however, no danger to the embedding process from these effects since the process temperature of maximum 200 0 C is well below the ignition temperatures. A method of measuring the dose rate of an unknown radioactive salt mixture at any point of this mixture has been developed. This is done by making two measurements with glass dose-meters, one with a beta-absorber to get a pure gamma dose and the other without it to get the combined beta and gamma dose. During the first measurement the dose-meters were protected against contamination by a thin layer of rubber

  14. Clinical relevance of DPYD variants c.1679T>G, c.1236G>A/HapB3, and c.1601G>A as predictors of severe fluoropyrimidine-associated toxicity : A systematic review and meta-analysis of individual patient data

    NARCIS (Netherlands)

    Meulendijks, Didier; Henricks, Linda M.; Sonke, Gabe S.; Deenen, Maarten J.; Froehlich, Tanja K.; Amstutz, Ursula; Largiadèr, Carlo R.; Jennings, Barbara A.; Marinaki, Anthony M.; Sanderson, Jeremy D.; Kleibl, Zdenek; Kleiblova, Petra; Schwab, Matthias; Zanger, Ulrich M.; Palles, Claire; Tomlinson, Ian; Gross, Eva; van Kuilenburg, André B P; Punt, Cornelis J A; Koopman, Miriam; Beijnen, Jos H.|info:eu-repo/dai/nl/071919570; Cats, Annemieke; Schellens, Jan H M|info:eu-repo/dai/nl/073926272

    2015-01-01

    Background: The best-known cause of intolerance to fluoropyrimidines is dihydropyrimidine dehydrogenase (DPD) deficiency, which can result from deleterious polymorphisms in the gene encoding DPD (DPYD), including. DPYD*2A and c.2846A>T. Three other variants- DPYD c.1679T>G, c.1236G>A/HapB3, and

  15. Clinical relevance of DPYD variants c.1679T>G, c.1236G>A/HapB3, and c.1601G>A as predictors of severe fluoropyrimidine-associated toxicity : a systematic review and meta-analysis of individual patient data

    NARCIS (Netherlands)

    Meulendijks, Didier; Henricks, Linda M; Sonke, Gabe S; Deenen, Maarten J; Froehlich, Tanja K; Amstutz, Ursula; Largiadèr, Carlo R; Jennings, Barbara A; Marinaki, Anthony M; Sanderson, Jeremy D; Kleibl, Zdenek; Kleiblova, Petra; Schwab, Matthias; Zanger, Ulrich M; Palles, Claire; Tomlinson, Ian; Gross, Eva; van Kuilenburg, André B P; Punt, Cornelis J A; Koopman, Miriam; Beijnen, Jos H; Cats, Annemieke; Schellens, Jan H M

    2015-01-01

    BACKGROUND: The best-known cause of intolerance to fluoropyrimidines is dihydropyrimidine dehydrogenase (DPD) deficiency, which can result from deleterious polymorphisms in the gene encoding DPD (DPYD), including DPYD*2A and c.2846A>T. Three other variants-DPYD c.1679T>G, c.1236G>A/HapB3, and

  16. Open TG-GATEs: a large-scale toxicogenomics database

    Science.gov (United States)

    Igarashi, Yoshinobu; Nakatsu, Noriyuki; Yamashita, Tomoya; Ono, Atsushi; Ohno, Yasuo; Urushidani, Tetsuro; Yamada, Hiroshi

    2015-01-01

    Toxicogenomics focuses on assessing the safety of compounds using gene expression profiles. Gene expression signatures from large toxicogenomics databases are expected to perform better than small databases in identifying biomarkers for the prediction and evaluation of drug safety based on a compound's toxicological mechanisms in animal target organs. Over the past 10 years, the Japanese Toxicogenomics Project consortium (TGP) has been developing a large-scale toxicogenomics database consisting of data from 170 compounds (mostly drugs) with the aim of improving and enhancing drug safety assessment. Most of the data generated by the project (e.g. gene expression, pathology, lot number) are freely available to the public via Open TG-GATEs (Toxicogenomics Project-Genomics Assisted Toxicity Evaluation System). Here, we provide a comprehensive overview of the database, including both gene expression data and metadata, with a description of experimental conditions and procedures used to generate the database. Open TG-GATEs is available from http://toxico.nibio.go.jp/english/index.html. PMID:25313160

  17. Influence of processing parameters on microstructure and tensile properties of TG6 titanium alloy

    International Nuclear Information System (INIS)

    Wang Tao; Guo Hongzhen; Wang Yanwei; Yao Zekun

    2010-01-01

    Research highlights: → This paper highlights the relationships among processing parameters, microstructure and tensile properties of TG6 high temperature titanium alloy. → The microstructural evolutions under different processing parameters were studied by the quantitative metallography, and the effects of microstructure on room and high temperature tensile properties of TG6 alloy were analysed by SEM and TEM. → Linear relationships of elongation vs. volume fraction of primary α phase and ultimate tensile strength vs. thickness of lamellar α phase were determined. - Abstract: Near-isothermal forging of the TG6 titanium alloy was conducted on microprocessor-controlled 630 ton hydraulic press at the deformation temperatures ranging from 850 deg. C to 1045 deg. C, the strain rates of 0.0008 s -1 , 0.003 s -1 and 0.008 s -1 and the deformation degree from 10% to 70%, and then different double heat treatments were applied to the forged specimens. The microstructural evolutions were researched by optical microscope and the microstructural features, i.e. volume fraction of primary α phase and thickness of lamellar α phase, were measured by means of the image analysis software. The room and high temperature tensile properties were obtained for all the specimens. Effects of microstructure on the properties were analysed by scanning electronic microscope. It was found that tenslie properties depended on microstructural features strongly. The plots of ultimate tensile strength vs. thickness of α lamellae and elongation vs. volume fraction of primary α phase produced straight lines. The liner equations were determined by fitting the experimental date, respectively. Compared to other parameters, heat treatment had more influence on the tensile strength and the tensile plasticity was more sensitive to the forging temperature.

  18. Comparison of Thyroglobulin Measurements Using Three Different Immunoassay Kits: A BRAMHS Tg-Plus RIA Kit, a BRAMHS hTg Sensitive Kryptor Kit, and a Beckman Coulter ACCESS Immunoassay Kit

    Directory of Open Access Journals (Sweden)

    Mijin Kim

    2016-09-01

    Full Text Available BackgroundSecond-generation thyroglobulin immunometric assays (Tg-IMAs have been developed with improved sensitivity. Our aim was to compare the diagnostic value of Tg-IMA measurements using a Kryptor (BRAHMS AG kit (Tg-K and an ACCESS (Beckman Coulter kit (Tg-A with that of the first-generation Tg measurement using a Tg-plus (BRAHMS AG kit (Tg+.MethodsWe enrolled 82 differentiated thyroid cancer patients who underwent total thyroidectomy with radioactive iodine remnant ablation and who underwent diagnostic whole body scan using recombinant human thyroid stimulating hormone (rhTSH. The Tg+, Tg-K, and Tg-A were measured before rhTSH administration during levothyroxine treatment (suppressed Tg from the same sample. Serum Tg+ was measured after rhTSH stimulation (stimulated Tg.ResultsSuppressed Tg+ was more significantly correlated with suppressed Tg-K (R2=0.919, P<0.001 than with suppressed Tg-A (R2=0.536, P<0.001. The optimal cut-off values of suppressed Tg+, Tg-K, and Tg-A for predicting stimulated Tg+ of 1 ng/mL were 0.3, 0.2, and 0.2 ng/mL, respectively. The sensitivity, specificity, and accuracy of suppressed Tg+ were 67%, 100%, and 90%, respectively; those of suppressed Tg-K were 83%, 90%, and 88%; those of suppressed Tg-A were 96%, 82%, and 87%, respectively. The positive predictive and negative predictive values of Tg+ were 100% and 87%, respectively; those of Tg-K were 79% and 92%; and those of Tg-A were 73% and 98%.ConclusionWe could not clearly demonstrate which kit had better diagnostic performance after comparison of first-generation Tg measurements with Tg-IMA measurements. Also, there were kit-to-kit variations between Tg-IMA kits. Suppressed Tg measured by Tg-IMA was insufficient to completely substitute for a stimulated Tg measurement.

  19. Prevalence of iodine- and thyroglobulin-negative findings in differentiated thyroid cancer. A retrospective analysis of patients treated from 1961 to 1998 in a university hospital; Haeufigkeit lod- und hTG-negativer Befunde beim differenzierten Schilddruesenkarzinom. Eine retrospektive Analyse der von 1961 bis 1998 in einer Universitaetsklinik behandelten Patienten

    Energy Technology Data Exchange (ETDEWEB)

    Klutmann, S.; Jenicke, L.; Geiss-Toenshoff, M.; Bohuslavizki, K.H.; Mester, J.; Clausen, M. [Universitaetskrankenhaus Eppendorf, Hamburg (Germany). Abt. fuer Nuklearmedizin

    2001-10-01

    Aim: The prevalence of iodine- and thyroglobulin-negative findings was evaluated in all patients with differentiated thyroid cancer (DTC) treated from 1961 until 1998 at the Department of Nuclear Medicine, University Hospital Hamburg-Eppendorf. Methods: A total of 490 patients with papillary thyroid cancer (PCA) and 242 patients with follicular thyroid cancer (FCA) were analyzed retrospectively. Patients were divided into four groups: 1: no recurrence, 2: recurrent disease, 3: primary metastatic/progressive disease and 4: inconclusive follow-up. Results of iodine scan, serum-TG, and additional imaging modalities as well as histology were compared in all patients. Results: 21/490 (4,3%) of patients with PCA and 16/242 (6,6%) with FCA suffered from recurrent disease. 62/490 (12,7%) of patients with PCA and 59/242 (24,4%) with FCA had primary metastatic/progressive disease. 12/21 patients with PCA and 12/16 with FCA showing up with recurrent disease had a negative iodinescan. 11/21 of patients with PCA and 4/16 with FCA and tumor recurrence had negative serum-TG levels. 14/62 patients with PCA and 14/59 with FCA presenting with primary metastatic/progressive disease had negative iodinescan. 14/62 patients with PCA and 6/59 with FCA had negative serum-TG. Conclusion: The prevalence of iodine-negative recurrent/metastatic disease is in accordance to the literature, whereas the prevalence of TG-negative recurrent/metastatic was noted higher than reported previously. Thus, the commonly used follow-up scheme of DTC is confirmed. However, iodine scan should be regularly performed in patients with high risk of recurrence. (orig.) [German] Ziel: Retrospektiv wurden alle von 1961 bis 1998 in der Abteilung fuer Nukleamedizin des Universitaetsklinikums Hamburg-Eppendorf behandelten Patienten mit einem differenzierten Schilddruesenkarzinom bezueglich des Anteils lod- und/oder hTG-negativer Rezidive analysiert. Methoden: Es wurden 490 Patienten mit einem papillaeren

  20. High Tg and fast curing epoxy-based anisotropic conductive paste for electronic packaging

    Science.gov (United States)

    Keeratitham, Waralee; Somwangthanaroj, Anongnat

    2016-03-01

    Herein, our main objective is to prepare the fast curing epoxy system with high glass transition temperature (Tg) by incorporating the multifunctional epoxy resin into the mixture of diglycidyl ether of bisphenol A (DGEBA) as a major epoxy component and aromatic diamine as a hardener. Furthermore, the curing behavior as well as thermal and thermomechanical properties were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and thermomechanical analysis (TMA). It was found that Tg obtained from tan δ of DGEBA/aromatic diamine system increased from 100 °C to 205 °C with the presence of 30 percentage by weight of multifunctional epoxy resin. Additionally, the isothermal DSC results showed that the multifunctional epoxy resin can accelerate the curing reaction of DGEBA/aromatic diamine system. Namely, a high degree of curing (˜90%) was achieved after a few minutes of curing at low temperature of 130 °C, owing to a large number of epoxy ring of multifunctional epoxy resin towards the active hydrogen atoms of aromatic diamine.

  1. Reaction of LiD with water vapor: thermogravimetric and scanning electron microscopy studies

    International Nuclear Information System (INIS)

    Balooch, M; Dinh, L N; LeMay, J D

    2000-01-01

    The kinetics of hydroxide film growth on LiD have been studied by the thermogravimetric method in nitrogen saturated with water vapor and by scanning electron microscopy (SEM) of samples that have been exposed to air with 50% relative humidity. The reaction probability is estimated to be 4 x 10 -7 for LiD exposed to ambient air with 50% relative humidity, suggesting that the diffusion through the hydroxide film is not the limiting step on the overall process at high moisture levels. The rate of growth is drastically reduced when the temperature is increased to 60 C

  2. Study on high-silicon boron-containing zeolite by thermogravimetric and IR-spectroscopy techniques

    International Nuclear Information System (INIS)

    Chukin, G.D.; Nefedov, B.K.; Surin, S.A.; Polinina, E.V.; Khusid, B.L.; Sidel'kovskaya, V.G.

    1985-01-01

    The structure identity of initial Na-forms of boron-containing and aluminosilicate high-silicon zeolites is established by thermogravimetric and IR-spectroscopy methods. The presence of boron in Na-forms of high-silicon zeolites is shown to lead to reduction of structure thermal stability. It is noted that thermal stability of the H-form of both high-silicon boron-containing and boron-free zeolites is practically equal and considerably higher than that of Na-forms

  3. Thermogravimetric analytical procedures for characterizing New Zealand and eastern Australian coals

    Energy Technology Data Exchange (ETDEWEB)

    Benfell, K.E.; Beamish, B.B.; Rodgers, K.A. [University of Auckland, Auckland (New Zealand). Dept. of Geology

    1996-09-01

    Under tightly constrained experimental conditions (particle size {lt}75 {mu}m, sample mass 5.0 {+-} 0.5 mg), heating rate 15{degree}C min{sup -1}, dry air purge 50 mL min{sup -1}, maximum temperature 900{degree}C a repeatability of {lt} {+-} 2{degree}C, may be achieved for significant temperatures that characterize the differential thermogravimetric burning profiles of typical medium-volatile, bituminous Australian Gondwanan coals and high-volatile, bituminous New Zealand Cretaceous-Tertiary coals.

  4. TU-E-BRB-03: Overview of Proposed TG-132 Recommendations

    Energy Technology Data Exchange (ETDEWEB)

    Brock, K. [University of Michigan (United States)

    2015-06-15

    Deformable image registration (DIR) is developing rapidly and is poised to substantially improve dose fusion accuracy for adaptive and retreatment planning and motion management and PET fusion to enhance contour delineation for treatment planning. However, DIR dose warping accuracy is difficult to quantify, in general, and particularly difficult to do so on a patient-specific basis. As clinical DIR options become more widely available, there is an increased need to understand the implications of incorporating DIR into clinical workflow. Several groups have assessed DIR accuracy in clinically relevant scenarios, but no comprehensive review material is yet available. This session will also discuss aspects of the AAPM Task Group 132 on the Use of Image Registration and Data Fusion Algorithms and Techniques in Radiotherapy Treatment Planning official report, which provides recommendations for DIR clinical use. We will summarize and compare various commercial DIR software options, outline successful clinical techniques, show specific examples with discussion of appropriate and inappropriate applications of DIR, discuss the clinical implications of DIR, provide an overview of current DIR error analysis research, review QA options and research phantom development and present TG-132 recommendations. Learning Objectives: Compare/contrast commercial DIR software and QA options Overview clinical DIR workflow for retreatment To understand uncertainties introduced by DIR Review TG-132 proposed recommendations.

  5. Cystatin C, CRP, log TG/HDLc and metabolic syndrome are associated with microalbuminuria in hypertension

    Energy Technology Data Exchange (ETDEWEB)

    Moura, Rafaela do Socorro Souza e Silva [Pós-Graduação em Ciências Médicas, Faculdade de Medicina, Universidade de Brasília, Brasília, DF (Brazil); Vasconcelos, Daniel França [Área de Cardiologia, Faculdade de Medicina, Universidade de Brasília, Brasília, DF (Brazil); Freitas, Eduardo [Departamento de Estatística, Universidade de Brasília, Brasília, DF (Brazil); Moura, Flavio José Dutra de; Rosa, Tânia Torres; Veiga, Joel Paulo Russomano, E-mail: joelprv@unb.br [Área de Clínica Médica, Nefrologia, Faculdade de Medicina, Universidade de Brasília, Brasília, DF (Brazil)

    2014-01-15

    In patients with systemic hypertension, microalbuminuria is a marker of endothelial damage and is associated with an increased risk for cardiovascular disease. To determine the factors that may lead to the occurrence of microalbuminuria in hypertensive patients with serum creatinine lower than 1.5 mg/dL. This cross-sectional study included 133 Brazilians with essential hypertension followed up at a hypertension outpatient clinic. Those with serum creatinine higher than 1.5 mg/dL, as well as those with diabetes mellitus, were excluded. Systolic and diastolic blood pressures were measured, and body mass index (BMI) and GFR estimated by using the CKD-EPI formula were calculated. The serum levels of the following were assessed: CysC, creatinine, total cholesterol, HDL cholesterol, LDL cholesterol, triglycerides, C-reactive protein (CRP) and fasting glucose. Microalbuminuria was determined in 24-hour urine. Hypertensive patients were classified according to the presence of one or more criteria for metabolic syndrome. In a multiple regression analysis, the serum levels of CysC and CRP, the atherogenic index log TG/HDLc and the presence of three or more criteria for metabolic syndrome were positively correlated with microalbuminuria (r{sup 2}: 0.277, p < 0.05). CysC, CRP, log TG/HDLc, and the presence of three or more criteria for metabolic syndrome, regardless of serum creatinine, were associated with microalbuminuria, an early marker of kidney damage and cardiovascular risk in patients with essential hypertension.

  6. Cystatin C, CRP, log TG/HDLc and metabolic syndrome are associated with microalbuminuria in hypertension

    International Nuclear Information System (INIS)

    Moura, Rafaela do Socorro Souza e Silva; Vasconcelos, Daniel França; Freitas, Eduardo; Moura, Flavio José Dutra de; Rosa, Tânia Torres; Veiga, Joel Paulo Russomano

    2014-01-01

    In patients with systemic hypertension, microalbuminuria is a marker of endothelial damage and is associated with an increased risk for cardiovascular disease. To determine the factors that may lead to the occurrence of microalbuminuria in hypertensive patients with serum creatinine lower than 1.5 mg/dL. This cross-sectional study included 133 Brazilians with essential hypertension followed up at a hypertension outpatient clinic. Those with serum creatinine higher than 1.5 mg/dL, as well as those with diabetes mellitus, were excluded. Systolic and diastolic blood pressures were measured, and body mass index (BMI) and GFR estimated by using the CKD-EPI formula were calculated. The serum levels of the following were assessed: CysC, creatinine, total cholesterol, HDL cholesterol, LDL cholesterol, triglycerides, C-reactive protein (CRP) and fasting glucose. Microalbuminuria was determined in 24-hour urine. Hypertensive patients were classified according to the presence of one or more criteria for metabolic syndrome. In a multiple regression analysis, the serum levels of CysC and CRP, the atherogenic index log TG/HDLc and the presence of three or more criteria for metabolic syndrome were positively correlated with microalbuminuria (r 2 : 0.277, p < 0.05). CysC, CRP, log TG/HDLc, and the presence of three or more criteria for metabolic syndrome, regardless of serum creatinine, were associated with microalbuminuria, an early marker of kidney damage and cardiovascular risk in patients with essential hypertension

  7. Thermal Phenomena in the Friction Process of the TG15 - Hard Anodic Coating Couple

    Directory of Open Access Journals (Sweden)

    Służałek G.

    2016-09-01

    Full Text Available The paper presents a one-dimensional model of heat conduction in a couple consisting of a cylinder made of a sliding plastic material, TG15, and a cuboid made of alloy AW 6061 coated with a hard anodic coating, where the couple is heated with the heat generated during friction. TG15 is a composite material based on polytetrafluoroethylene (PTFE with a 15% graphite filler, used for piston rings in oil-free air-compressors. Measurement of temperature in the friction zone is extremely important for the understanding and analysis of the phenomena occurring therein. It is practically impossible to introduce a temperature sensor in such a place. Therefore, the interaction taking place in such a couple was modelled using numerical methods. In order to simplify and accelerate the calculations, a one-dimensional model and constant thermophysical parameters of the materials participating in friction were adopted. To solve the proposed model, the finite difference method was used (FDM. The resultant system of equations was solved by means of an explicit scheme.

  8. Use of a fluidized bed combustor and thermogravimetric analyzer for the study of coal ignition temperature

    International Nuclear Information System (INIS)

    Ávila, Ivonete; Crnkovic, Paula M.; Luna, Carlos M.R.; Milioli, Fernando E.

    2017-01-01

    Highlights: • Coal ignition tests were conducted in a fluidized bed and thermogravimetric conditions. • The use of two different ignition criteria showed a similar coal ignition temperature. • Coal ignition temperature was obtained by the changes of gas concentrations in FBC. • Ignition temperatures were associated with the activation energy of coal combustion. - Abstract: Ignition experiments with two bituminous coals were carried out in an atmospheric bubbling fluidized bed combustor (FBC) and a thermogravimetric analyzer (TGA). In the FBC tests, the rapid increase in O_2, CO_2, and SO_2 concentrations is an indication of the coal ignition. In the TGA technique, the ignition temperature was determined by the evaluation of the TGA curves in both combustion and pyrolysis processes. Model-Free Kinetics was applied and the coal ignition temperatures were associated with changes in the activation energy values during the combustion process. The results show the coal with the lowest activation energy also showed the lowest ignition temperature, highest values of volatile content and a higher heating value. The application of two different ignition criteria (TGA and FBC) resulted in similar ignition temperatures. The FBC curves indicated the high volatile coal ignites in the freeboard, i.e. during the feeding in the reactor, whereas the low volatile coal ignites in the bed. Finally, the physicochemical characteristics of the investigated coal types were correlated with their reactivities for the prediction of the ignition temperatures behaviors under different operating conditions as those in FBC.

  9. Thermogravimetric studies on electron beam initiated grafting of triallyl cyanurate onto polyethylene

    International Nuclear Information System (INIS)

    Chaki, T.K.; Bhowmik, A.K.; Mukunda, P.G.; Majali, A.B.; Tikku, V.K.

    1993-01-01

    Low density polyethylene (LDPE) containing different levels of triallyl cyanurate (TAC) have been prepared in a Brabender Plasticorder at 120 degC. The moulded samples in the form of rectangular compression sheet were irradiated under electron beam accelerator with different irradiation doses. Thermogravimetric and derivative thermogravimetric analyses of the irradiated samples grafted with TAC have been carried out in order to explore the decomposition behaviour and kinetics of decomposition under nitrogen atmosphere. Initial decomposition temperature (Ti), temperature at which 50% weight loss takes place (T50), final decomposition temperature (Tf) and the kinetic parameters evaluated from TGA traces of samples at different radiation doses (constant TAC level) and at different levels of TAC (constant radiation dose) have been reported. The effect of radiation dose and TAC level on the grafting of TAC onto polyethylene have been explained on the basis of degradation characteristics of irradiated samples. Kinetic studies show that the degradation of the irradiated samples follow first order reaction kinetics. Activation energies of degradation have been determined using McCarty and Green's method. Activation energy of the irradiated samples increases with the increasing radiation dose and also with increasing level of TAC. (author). 3 tabs

  10. Mefenamic acid conjugates based on a hydrophilic biopolymer hydroxypropylcellulose: novel prodrug design, characterization and thermal analysis

    International Nuclear Information System (INIS)

    Hussain, M.A.; Kausar, R.; Amin, M.

    2015-01-01

    Macromolecular prodrugs (MPDs) of mefenamic acid were designed onto a cellulose ether derivative hydroxypropylcellulose (HPC) as ester conjugates. Fabrication of HPC-mefenamic acid conjugates was achieved by using p-toluenesulfonyl chloride as carboxylic acid (a functional group in drug) activator at 80 degree C for 24 h under nitrogen atmosphere. Reaction was preceded under homogeneous reaction conditions as HPC was dissolved before use in DMAc solvent. Imidazole was used as a base. Easy workup reactions resulted in good yields (55-65%) and degree of substitution (DS) of drug (0.37-0.99) onto HPC. The DS was calculated by acid-base titration after saponification and UV/Vis spectrophotometry after hydrolysis. DS by both of the methods was found in good agreement with each other. Aqueous and organic soluble novel prodrugs of mefenamic acid were purified and characterized by different spectroscopic and thermal analysis techniques. The initial, maximum and final degradation temperatures of HPC, mefenamic acid and HPC-mefenamic acid conjugates were drawn from thermogravimetric (TG) and derivative TG curves and compared to access relative thermal stability. The TG analysis has indicated that samples obtained were thermally more stable especially with increased stability of mefenamic acid in HPC-mefenamic acid conjugates. These novel MPDs of mefenamic acid (i.e., HPC-mefenamic acid conjugates) may have potential applications in pharmaceutically viable drug design due to wide range of solubility and extra thermal stability imparted after MPD formation. (author)

  11. THERMOGRAVIMETRIC INVESTIGATION AND THERMAL CONVERSION KINETICS OF TYPICAL NORTH-AFRICA AND MIDDLE-EAST LIGNOCELLULOSIC WASTES

    Directory of Open Access Journals (Sweden)

    2012-01-01

    Full Text Available The aim of this work was to thermally characterize the renewable lignocellulosic bioresources derived from palm trees in order to highlight their energy potential. Pyrolysis and combustion behaviours of date stones (DS agricultural by-products were tested by thermo-gravimetric analysis, and the main chemical compositions were analyzed. The work has also been conducted to identify their most important physical characteristics. The study of the sizes and heating rate effects constitute the first part of the experimental work. Inert atmosphere and three heating rates: 10, 20, and 50 °C/min, were applied to various particle sizes of DS. In the second part, tests were carried out in an oxidizing atmosphere (21% O2 by varying the size of the DS. The kinetic parameters such as pre-exponential factor and activation energy were determined. Increasing the particle sizes and the heating rates didn’t have an appreciable influence on the global weight losses. However, degradation rates were significant with the porous structure of the DS. Weight losses in inert and oxidizing atmospheres were found to occur in two stages (drying and devolatilization and in three stages (drying, devolatilization, and oxidation of the char.

  12. Thermogravimetric kinetic modelling of in-situ catalytic pyrolytic conversion of rice husk to bioenergy using rice hull ash catalyst.

    Science.gov (United States)

    Loy, Adrian Chun Minh; Gan, Darren Kin Wai; Yusup, Suzana; Chin, Bridgid Lai Fui; Lam, Man Kee; Shahbaz, Muhammad; Unrean, Pornkamol; Acda, Menandro N; Rianawati, Elisabeth

    2018-04-07

    The thermal degradation behaviour and kinetic parameter of non-catalytic and catalytic pyrolysis of rice husk (RH) using rice hull ash (RHA) as catalyst were investigated using thermogravimetric analysis at four different heating rates of 10, 20, 50 and 100 K/min. Four different iso conversional kinetic models such as Kissinger, Friedman, Kissinger-Akahira-Sunose (KAS) and Ozawa-Flynn-Wall (OFW) were applied in this study to calculate the activation energy (E A ) and pre-exponential value (A) of the system. The E A of non-catalytic and catalytic pyrolysis was found to be in the range of 152-190 kJ/mol and 146-153 kJ/mol, respectively. The results showed that the catalytic pyrolysis of RH had resulted in a lower E A as compared to non-catalytic pyrolysis of RH and other biomass in literature. Furthermore, the high Gibb's free energy obtained in RH implied that it has the potential to serve as a source of bioenergy production. Copyright © 2018 Elsevier Ltd. All rights reserved.

  13. Comparative study on pyrolysis of lignocellulosic and algal biomass using a thermogravimetric and a fixed-bed reactor.

    Science.gov (United States)

    Yuan, Ting; Tahmasebi, Arash; Yu, Jianglong

    2015-01-01

    Pyrolysis characteristics of four algal and lignocellulosic biomass samples were studied by using a thermogravimetric analyzer (TGA) and a fixed-bed reactor. The effects of pyrolysis temperature and biomass type on the yield and composition of pyrolysis products were investigated. The average activation energy for pyrolysis of biomass samples by FWO and KAS methods in this study were in the range of 211.09-291.19kJ/mol. CO2 was the main gas component in the early stage of pyrolysis, whereas H2 and CH4 concentrations increased with increasing pyrolysis temperature. Bio-oil from Chlorellavulgaris showed higher content of nitrogen containing compounds compared to lignocellulosic biomass. The concentration of aromatic organic compounds such as phenol and its derivatives were increased with increasing pyrolysis temperature up to 700°C. FTIR analysis results showed that with increasing pyrolysis temperature, the concentration of OH, CH, CO, OCH3, and CO functional groups in char decreased sharply. Copyright © 2014 Elsevier Ltd. All rights reserved.

  14. Comparative study by TG and DSC Of membranes polyamide66/bentonite clay nanocomposite; Estudo comparativo por TG e DSC de membranas de nanocompositos poliamida66/argila bentonitica

    Energy Technology Data Exchange (ETDEWEB)

    Medeiros, K.M. de; Kojuch, L R; Araujo, E M; Lira, H.L., E-mail: keilamm@ig.com.b [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Unidade Academica de Engenharia de Materiais; Lima, F [Universidade Estadual da Paraiba (UEPB), Campina Grande, PB (Brazil). Dept. de Quimica

    2010-07-01

    In this study, it was obtained membranes of nanocomposites polyamide66 with 3 and 5% bentonite clay consists of silicates in layers from the interior of Paraiba. The clay was treated with a quaternary ammonium salt in order to make it organophilic. The membranes were prepared by phase inversion technique from the nanocomposites in solution. The clays were characterized by X-ray diffraction (XRD) and thermogravimetry (TG). Also the membranes were characterized by differential scanning calorimetry (DSC) and TG. The XRD and TG confirmed the presence of salt in the clay and thermal stability of the treated clay. For DSC, it was observed that there was no change in melting temperature of the membranes of nanocomposites compared to membrane pure polyamide66. By TG, it was found that the decomposition of the membranes of polyamide66 with treated clay were higher compared with the untreated clay. (author)

  15. Yeast three-hybrid screen identifies TgBRADIN/GRA24 as a negative regulator of Toxoplasma gondii bradyzoite differentiation.

    Directory of Open Access Journals (Sweden)

    Anahi V Odell

    Full Text Available Differentiation of the protozoan parasite Toxoplasma gondii into its latent bradyzoite stage is a key event in the parasite's life cycle. Compound 2 is an imidazopyridine that was previously shown to inhibit the parasite lytic cycle, in part through inhibition of parasite cGMP-dependent protein kinase. We show here that Compound 2 can also enhance parasite differentiation, and we use yeast three-hybrid analysis to identify TgBRADIN/GRA24 as a parasite protein that interacts directly or indirectly with the compound. Disruption of the TgBRADIN/GRA24 gene leads to enhanced differentiation of the parasite, and the TgBRADIN/GRA24 knockout parasites show decreased susceptibility to the differentiation-enhancing effects of Compound 2. This study represents the first use of yeast three-hybrid analysis to study small-molecule mechanism of action in any pathogenic microorganism, and it identifies a previously unrecognized inhibitor of differentiation in T. gondii. A better understanding of the proteins and mechanisms regulating T. gondii differentiation will enable new approaches to preventing the establishment of chronic infection in this important human pathogen.

  16. Differential thermal, Thermogravimetric and X-ray diffraction investigation of hydration phases in cementitious waste form

    International Nuclear Information System (INIS)

    Khalil, M.Y.; Nagy, M.E.; El-Sourougy, M.R.; Zaki, A.A.

    1996-01-01

    Hydration phases of cement determine the final properties of the product. Adding other components to the cement paste may alter the final phases formed and affect properties of the hardened products. In this work ordinary portland cement and/or blast furnace slag cement were hardened with low-or intermediate-level radioactive liquid wastes and different additives. Hydration phases were investigated using differential thermal, thermogravimetric, and X-ray diffraction techniques. Low-and intermediate-level liquid wastes were found not to affect the hydration phases of cement. The addition of inorganic exchangers and latex were found to affect the hydration properties of the cement waste system. This resulted in a reduction of compressive strength. On the contrary, addition of epoxy also affected the hydration causing increase in compressive strength. 10 figs., 2 tabs

  17. Thermogravimetric study of the pyrolysis of biomass residues from tomato processing industry

    Energy Technology Data Exchange (ETDEWEB)

    Mangut, V.; Sabio, E.; Ganan, J.; Gonzalez, J.F.; Ramiro, A.; Gonzalez, C.M.; Roman, S.; Al-Kassir, A. [Department of Chemical and Energy Engineering, University of Extremadura, Avda. de Elvas s/n, 06071 Badajoz (Spain)

    2006-01-15

    There is an increasing concern with the environmental problems associated with the increasing CO{sub 2}, NO{sub x} and SO{sub x} emissions resulting from the rising use of fossil fuels. Renewable energy, mainly biomass, can contribute to reduce the fossil fuels consumption. Biomass is a renewable resource with a widespread world distribution. Tomato processing industry produces a high amount of biomass residue (peel and seeds) that could be used for thermal energy and electricity. A characterization and thermogravimetric study has been carried out. The residue has a high HHV and volatile content, and a low ash, and S contents. A kinetic model has been developed based on the degradation of hemicellulose, cellulose, lignin and oil that describe the pyrolysis of peel, seeds and peel and seeds residues. (author)

  18. Thermogravimetric kinetics of corn stalk pretreated by oleaginous fungi Cunninghamella echinulata.

    Science.gov (United States)

    Wu, Jianguo; Gao, Shi; Wan, Jilin; Zeng, Yelin; Ma, Fuying; Zhang, Xiaoyu

    2011-04-01

    The thermogravimetric and composition of corn stalk pretreated by oleaginous fungi Cunninghamella echinulata had been studied in this paper. Results indicated that pretreatment by oleaginous fungi C. echinulata could decrease the activation energy and make the pyrolysis more efficient and energy-saving. By bio-pretreatment, the contents of elements agreed with the weight loss, sugar content, and oil contents, especially the sulfur content was greatly decreased, greatly eliminating the inventory of gas contamination such as the emission of SOx and making the pyrolysis more environmentally friendly. Therefore, corn stalk with sugar pretreated by oleaginous fungi C. echinulata should be a good pyrolysis material to obtain high quality bio-oil. Copyright © 2011 Elsevier Ltd. All rights reserved.

  19. Thermogravimetric investigation on characteristic of biomass combustion under the effect of organic calcium compounds.

    Science.gov (United States)

    Zhang, Lihui; Duan, Feng; Huang, Yaji

    2015-01-01

    Experiments were conducted in a thermogravimetric analyzer to investigate thermal behavior of different organic calcium compounds (OCCs) and its blended fuels with three kinds of biomass. The effectiveness of synthesized method for OCC was assessed by the pyrolysis test. Effect of the mole ratio of calcium to sulfur on co-combustion characteristics was studied. Results indicated that preparation method of modified calcium acetate (MCA) had high precision and accuracy. Co-combustion characteristic of OCCs blended with biomass was controlled by OCCs' additive amount and the content of volatile matter which is mainly composed of small hydrocarbon molecules. Combustion performance indexes for peanut shell and wheat straw impregnated by OCCs were improved, however, an inverse trend was found for rice husk because of lower additive amount of OCCs. The blended fuel show higher combustion performance indexes compared with combustion of individual biomass, and these indexes decrease with increases of Ca/S ratio. Copyright © 2014 Elsevier Ltd. All rights reserved.

  20. A vacuum thermogravimetric method for outgassing evaluations of silicone-coated fiberglass cloth

    Science.gov (United States)

    Jensen, L. B.; Mccauley, G. B.; Honma, M.; Hultquist, A. E.

    1972-01-01

    A method for evaluating outgassing characteristics of space-sensitive materials was devised by modifying a thermogravimetric balance so that a continual weight loss trace is obtained as a function of time at constant temperature and nearly constant pressure. In addition the apparatus is capable of collecting room temperature condensibles during the outgassing run. A series of silicone-coated glass cloth samples were evaluated by this method. The major advantage of the technique is that data presentation is developed in the form of a continuous trace. This data can then be utilized to develop the kinetics of weight loss. The technique has been shown to be a useful and valid one for indicating small differences between materials under vacuum and elevated temperature conditions.

  1. Thermogravimetric analytical procedures for determining reactivities of chars from New Zealand coals

    Energy Technology Data Exchange (ETDEWEB)

    Shaw, K.J.; Beamish, B.B.; Rodgers, K.A. [University of Auckland, Auckland (New Zealand). Dept. of Geology

    1997-10-22

    This paper describes how tightly constrained thermogravimetric experimental procedures (particle size {lt} 212 {mu}m, sample mass 15.5 mg, CO{sub 2} reactant gas, near isothermal conditions) allow the reactivity of chars from high volatile New Zealand coals to be determined to a repeatability of {+-}0.07 h{sup -1} at 900{degree}C and {+-}0.5 h{sup -1} at 1100{degree}C. The procedure also provides proximate analyses information and affords a quick ({lt} 90 min) comparison between different coal types as well as indicating likely operating conditions and problems associated with a particular coal or blend. A clear difference is evident between reactivities of differing New Zealand coal ranks. Between 900 and 1100{degree}C, bituminous coals increase thirtyfold in reactivity compared with fourfold for subbituminous, with the latter being three to five times greater in reactivity at higher temperature.

  2. Thermogravimetric determination of the carbon dioxide reactivity of char from some New Zealand coals and its association with the inorganic geochemistry of the parent coal

    Energy Technology Data Exchange (ETDEWEB)

    Beamish, B.B.; Shaw, K.J.; Rodgers, K.A.; Newman, J. [University of Auckland, Auckland (New Zealand). Dept. of Geology

    1998-02-01

    Thermogravimetrically-determined carbon dioxide reactivities of char formed from New Zealand coals, ranging in rank from lignite to high volatile bituminous, vary from 0.12 to 10.63 mg/h/mg on a dry, ash-free basis. The lowest rank subbituminous coal chars have similar reactivities to the lignite coal chars. Calcium content of the char shows the strongest correlation with reactivity, which increases as the calcium content increases. High calcium per se does not directly imply a high char reactivity. Organically-bound calcium catalyses the conversion of carbon to carbon monoxide in the presence of carbon dioxide, whereas calcium present as discrete minerals in the coal matrix e.g., calcite, fails to significantly affect reactivity. Catalytic effects of magnesium, iron, sodium and phosphorous are not as obvious, but can be recognised for individual chars. The thermogravimetric technique provides a fast, reliable analysis that is able to distinguish char reactivity differences between coals, which may be due to any of the above effects. 27 refs., 6 figs., 4 tabs.

  3. Molten salt corrosion behavior of structural materials in LiCl-KCl-UCl3 by thermogravimetric study

    Science.gov (United States)

    Rao, Ch Jagadeeswara; Ningshen, S.; Mallika, C.; Mudali, U. Kamachi

    2018-04-01

    The corrosion resistance of structural materials has been recognized as a key issue in the various unit operations such as salt purification, electrorefining, cathode processing and injection casting in the pyrochemical reprocessing of spent metallic nuclear fuels. In the present work, the corrosion behavior of the candidate materials of stainless steel (SS) 410, 2.25Cr-1Mo and 9Cr-1Mo steels was investigated in molten LiCl-KCl-UCl3 salt by thermogravimetric analysis under inert and reactive atmospheres at 500 and 600 °C, for 6 h duration. Insignificant weight gain (less than 1 mg/cm2) in the inert atmosphere and marginal weight gain (maximum 5 mg/cm2) in the reactive atmosphere were observed at both the temperatures. Chromium depletion rates and formation of Cr-rich corrosion products increased with increasing temperature of exposure in both inert and reactive atmospheres as evidenced by SEM and EDS analysis. The corrosion attack by LiCl-KCl-UCl3 molten salt, under reactive atmosphere for 6 h duration was more in the case of SS410 than 9Cr-1Mo steel followed by 2.25Cr-1Mo steel at 500 °C and the corrosion attack at 600 °C followed the order: 9Cr-1Mo steel >2.25Cr-1Mo steel > SS410. Outward diffusion of the minor alloying element, Mo was observed in 9Cr-1Mo and 2.25Cr-1Mo steels at both temperatures under reactive atmosphere. Laser Raman spectral analysis of the molten salt corrosion tested alloys under a reactive atmosphere at 500 and 600 °C for 6 h revealed the formation of unprotected Fe3O4 and α-as well as γ-Fe2O3. The results of the present study facilitate the selection of structural materials for applications in the corrosive molten salt environment at high temperatures.

  4. Thermogravimetric study of oxidation of a PdCr alloy used for high-temperature sensors

    Science.gov (United States)

    Boyd, Darwin L.; Zeller, Mary V.

    1994-01-01

    In this study, the oxidation of Pd-13 weight percent Cr, a candidate alloy for high-temperature strain gages, was investigated by thermogravimetry. Although the bulk alloy exhibits linear electrical resistivity versus temperature and stable resistivity at elevated temperatures, problems attributed to oxidation occur when this material is fabricated into strain gages. In this work, isothermal thermogravimetry (TG) was used to study the oxidation kinetics. Results indicate that the oxidation of Pd-13 weight percent Cr was approximately parabolic in time at 600 C but exhibited greater passivation from 700 to 900 C. At 1100 C, the oxidation rate again increased.

  5. U.S. Army RDECOM-ARDEC's results of the TG-53 experiment and field test

    Science.gov (United States)

    Desai, Sachi V.; Morcos, Amir

    2009-05-01

    Herein is described the U.S. Army RDECOM-ARDEC's purpose and series of activities conducted at the 2008 NATO SET-093 TG-53 experiment and field test. The overall purpose of the field test as stated by SET-093 panel was to provide a baseline test capable of providing relevant scenarios and data regarding a variety of impulsive generated acoustic events. As organized, the field experiment also allowed the room o study sensor interoperability across multiple platforms and multi-national users via the spider communication framework/reporting structure. This multinational network maintained by the host ETBS with a standardized messaging format with specific goals for each participating organization. ARDEC's role and purpose for the test was to provide situational awareness via the Spider and associated messaging format to the ETBS command center while continuing to gather unique acoustic data from various vantage points. ARDEC had several deliverables for the TG-53 field experiment derived from the mission and spirit of the field test. The most relevant deliverable was to demonstrate sensor interoperability via the Spider network and provide situational awareness by describing the said mortar/artillery events. The second purpose revolved around a relevant environment algorithm validation of the muzzle blast discrimination for future UGS transition in particular the UTAMS II. The algorithm validation information remained internal to the specific data acquisition system and not broadcasted out on the Spider network. The TG-53 field experiments provided the added opportunity to further test and refine the algorithm based on the discrete wavelet transform (DWT) and multiresolution analysis. These techniques are used to classify and reliably discriminates between launch and impact artillery and/or mortar events via acoustic signals produced during detonation. Distinct characteristics are found within the acoustic signatures since impact events emphasize concussive and

  6. A thermogravimetric analyzer for corrosive atmospheres, and its application to the chlorination of ZrO2-C mixtures

    International Nuclear Information System (INIS)

    Pasquevich, Daniel; Caneiro, Alberto

    1990-01-01

    A thermogravimetric analyzer built on the basis of a Cahn 2000 electrobalance, suitable for using with corrosive atmospheres, is reported. The corrections for buoyancy and gas-flow effects, which strongly modify the thermogravimetric curves are discussed. As an application, the kinetics of a reaction between chlorine and a mixture of zirconia and carbon has been studied. It has been able to measure the uptake of chlorine by carbon and the reaction rate within the first 50 seconds. Evidence of a transition to quite a different reaction rate at longer times is presented. (Author)

  7. Tissue transglutaminase (TG2 activity regulates osteoblast differentiation and mineralization in the SAOS-2 cell line

    Directory of Open Access Journals (Sweden)

    Xiaoxue Yin

    2012-08-01

    Full Text Available Tissue transglutaminase (type II, TG2 has long been postulated to directly promote skeletal matrix calcification and play an important role in ossification. However, limited information is available on the expression, function and modulating mechanism of TG2 during osteoblast differentiation and mineralization. To address these issues, we cultured the well-established human osteosarcoma cell line SAOS-2 with osteo-inductive conditioned medium and set up three time points (culture days 4, 7, and 14 to represent different stages of SAOS-2 differentiation. Osteoblast markers, mineralization, as well as TG2 expression and activity, were then assayed in each stage. Furthermore, we inhibited TG activity with cystamine and then checked SAOS-2 differentiation and mineralization in each stage. The results showed that during the progression of osteoblast differentiation SAOS-2 cells presented significantly high levels of osteocalcin (OC mRNA, bone morphogenetic protein-2 (BMP-2 and collagen I, significantly high alkaline phosphatase (ALP activity, and the increased formation of calcified matrix. With the same tendency, TG2 expression and activity were up-regulated. Furthermore, inhibition of TG activity resulted in a significant decrease of OC, collagen I, and BMP-2 mRNA and of ALP activity and mineralization. This study demonstrated that TG2 is involved in osteoblast differentiation and may play a role in the initiation and regulation of the mineralization processes. Moreover, the modulating effects of TG2 on osteoblasts may be related to BMP-2.

  8. Endogenous murine tau promotes neurofibrillary tangles in 3xTg-AD mice without affecting cognition.

    Science.gov (United States)

    Baglietto-Vargas, David; Kitazawa, Masashi; Le, Elaine J; Estrada-Hernandez, Tatiana; Rodriguez-Ortiz, Carlos J; Medeiros, Rodrigo; Green, Kim N; LaFerla, Frank M

    2014-02-01

    Recent studies on tauopathy animal models suggest that the concomitant expression of the endogenous murine tau delays the pathological accumulation of human tau, and interferes with the disease progression. To elucidate the role of endogenous murine tau in a model with both plaques and tangles, we developed a novel transgenic mouse model by crossing 3xTg-AD with mtauKO mice (referred to as 3xTg-AD/mtauKO mice). Therefore, this new model allows us to determine the pathological consequences of the murine tau. Here, we show that 3xTg-AD/mtauKO mice have lower tau loads in both soluble and insoluble fractions, and lower tau hyperphosphorylation level in the soluble fraction relative to 3xTg-AD mice. In the 3xTg-AD model endogenous mouse tau is hyperphosphorylated and significantly co-aggregates with human tau. Despite the deletion of the endogenous tau gene in 3xTg-AD/mtauKO mice, cognitive dysfunction was equivalent to 3xTg-AD mice, as there was no additional impairment on a spatial memory task, and thus despite increased tau phosphorylation, accumulation and NFTs in 3xTg-AD mice no further effects on cognition are seen. These findings provide better understanding about the role of endogenous tau to Alzheimer's disease (AD) pathology and for developing new AD models. © 2013.

  9. Thermogravimetric and microscopic analysis of SiC/SiC materials with advanced interfaces

    Energy Technology Data Exchange (ETDEWEB)

    Windisch, C.F. Jr.; Jones, R.H. [Pacific Northwest National Lab., Richland, WA (United States); Snead, L.L. [Oak Ridge National Lab., TN (United States)

    1997-04-01

    The chemical stability of SiC/SiC composites with fiber/matrix interfaces consisting of multilayers of SiC/SiC and porous SiC have been evaluated using a thermal gravimetric analyzer (TGA). Previous evaluations of SiC/SiC composites with carbon interfacial layers demonstrated the layers are not chemically stable at goal use temperatures of 800-1100{degrees}C and O{sub 2} concentrations greater than about 1 ppm. No measureable mass change was observed for multilayer and porous SiC interfaces at 800-1100{degrees}C and O{sub 2} concentrations of 100 ppm to air; however, the total amount of oxidizable carbon is on the order of the sensitivity of the TGA. Further studies are in progress to evaluate the stability of these materials.

  10. Discernment of synergism in pyrolysis of biomass blends using thermogravimetric analysis.

    Science.gov (United States)

    Mallick, Debarshi; Poddar, Maneesh Kumar; Mahanta, Pinakeswar; Moholkar, Vijayanand S

    2018-04-12

    This study reports pyrolysis kinetics of biomass blends using isoconversional methods, viz. Friedman, FWO and KAS. Blends of three biomasses, viz. saw dust, bamboo dust and rice husk, were used. Extractives and volatiles in biomass and minerals in ash had marked influence on enhancement of reaction kinetics during co-pyrolysis, as indicated by reduction in activation energy and increase in decomposition intensity. Pyrolysis kinetics of saw dust and rice husk accelerated (positive synergy), while that of bamboo dust decelerated after blending (negative synergy). Predominant reaction mechanism of all biomass blends was 3-D diffusion in lower conversion range (α ≤ 0.5), while for α ≥ 0.5 pyrolysis followed random nucleation (or nucleation and growth mechanism). Higher reaction order for pyrolysis of blends of rice husk with saw dust and bamboo dust was attributed to catalytic effect of minerals in ash. Positive ΔH and ΔG was obtained for pyrolysis of all biomass blends. Copyright © 2018 Elsevier Ltd. All rights reserved.

  11. Analysis of unburned carbon in industrial ashes from biomass combustion by thermogravimetric method using Boudouard reaction

    Czech Academy of Sciences Publication Activity Database

    Straka, Pavel; Náhunková, Jana; Žaloudková, Margit

    2014-01-01

    Roč. 575, JAN (2014), s. 188-194 ISSN 0040-6031 R&D Projects: GA MZe QI102A207 Institutional support: RVO:67985891 Keywords : unburned carbon * biomass * ash * thermogravimetry Subject RIV: GD - Fertilization, Irrigation, Soil Processing Impact factor: 2.184, year: 2014 http://www.sciencedirect.com/science/article/pii/S0040603113005455

  12. Measurements of Gasification Characteristics of Coal and Char in CO2-Rich Gas Flow by TG-DTA

    Directory of Open Access Journals (Sweden)

    Zhigang Li

    2013-01-01

    Full Text Available Pyrolysis, combustion, and gasification properties of pulverized coal and char in CO2-rich gas flow were investigated by using gravimetric-differential thermal analysis (TG-DTA with changing O2%, heating temperature gradient, and flow rate of CO2-rich gases provided. Together with TG-DTA, flue gas generated from the heated coal, such as CO, CO2, and hydrocarbons (HCs, was analyzed simultaneously on the heating process. The optimum O2% in CO2-rich gas for combustion and gasification of coal or char was discussed by analyzing flue gas with changing O2 from 0 to 5%. The experimental results indicate that O2% has an especially large effect on carbon oxidation at temperature less than 1100°C, and lower O2 concentration promotes gasification reaction by producing CO gas over 1100°C in temperature. The TG-DTA results with gas analyses have presented basic reference data that show the effects of O2 concentration and heating rate on coal physical and chemical behaviors for the expected technologies on coal gasification in CO2-rich gas and oxygen combustion and underground coal gasification.

  13. The polyphenol oleuropein aglycone protects TgCRND8 mice against Aß plaque pathology.

    Directory of Open Access Journals (Sweden)

    Cristina Grossi

    Full Text Available The claimed beneficial effects of the Mediterranean diet include prevention of several age-related dysfunctions including neurodegenerative diseases and Alzheimer-like pathology. These effects have been related to the protection against cognitive decline associated with aging and disease by a number of polyphenols found in red wine and extra virgin olive oil. The double transgenic TgCRND8 mice (overexpressing the Swedish and Indiana mutations in the human amyloid precursor protein, aged 1.5 and 4, and age-matched wild type control mice were used to examine in vivo the effects of 8 weeks dietary supplementation of oleuropein aglycone (50 mg/kg of diet, the main polyphenol found in extra virgin olive oil. We report here that dietary supplementation of oleuropein aglycone strongly improves the cognitive performance of young/middle-aged TgCRND8 mice, a model of amyloid-ß deposition, respect to age-matched littermates with un-supplemented diet. Immunofluorescence analysis of cerebral tissue in oleuropein aglycone-fed transgenic mice showed remarkably reduced ß-amyloid levels and plaque deposits, which appeared less compact and "fluffy"; moreover, microglia migration to the plaques for phagocytosis and a remarkable reduction of the astrocyte reaction were evident. Finally, oleuropein aglycone-fed mice brain displayed an astonishingly intense autophagic reaction, as shown by the increase of autophagic markers expression and of lysosomal activity. Data obtained with cultured cells confirmed the latter evidence, suggesting mTOR regulation by oleuropein aglycone. Our results support, and provide mechanistic insights into, the beneficial effects against Alzheimer-associated neurodegeneration of a polyphenol enriched in the extra virgin olive oil, a major component of the Mediterranean diet.

  14. Re-examining TG-142 recommendations in light of modern techniques for linear accelerator based radiosurgery.

    Science.gov (United States)

    Faught, Austin M; Trager, Michael; Yin, Fang-Fang; Kirkpatrick, John; Adamson, Justus

    2016-10-01

    The recent development of multifocal stereotactic radiosurgery (SRS) using a single isocenter volumetric modulated arc theory (VMAT) technique warrants a re-examination of the quality assurance (QA) tolerances for routine mechanical QA recommended by the American Association of Physicists in Medicine Task Group Report Number 142. Multifocal SRS can result in targets with small volumes being at a large off-axis distance from the treatment isocenter. Consequently, angular errors in the collimator, patient support assembly (PSA), or gantry could have an increased impact on target coverage. The authors performed a retrospective analysis of dose deviations caused by systematic errors in PSA, collimator, and gantry angle at the tolerance level for routine linear accelerator QA as recommended by TG-142. Dosimetric deviations from multifocal SRS plans (N = 10) were compared to traditional single target SRS using dynamic conformal arcs (N = 10). The chief dosimetric quantities used in determining clinical impact were V 100% and D 99% of the individual planning target volumes and V 12Gy of the healthy brain. Induced errors at tolerance levels showed the greatest change in multifocal SRS target coverage for collimator rotations (±1.0°) with the average changes to V 100% and D 99% being 5% and 6%, respectively, with maximum changes of 33% and 20%. A reduction in the induced error to half the TG-142 tolerance (±0.5°) demonstrated similar changes in coverage loss to traditional single target SRS assessed at the recommended tolerance level. The observed change in coverage for multifocal SRS was reduced for gantry errors (±1.0°) at 2% and 4.5% for V 100% and D 99% , respectively, with maximum changes of 18% and 12%. Minimal change in coverage was noted for errors in PSA rotation. This study indicates that institutions utilizing a single isocenter VMAT technique for multifocal disease should pay careful attention to the angular mechanical tolerances in designing a robust and

  15. A Thermomechanical and Adhesion Analysis of Epoxy/Al2O3 Nanocomposites

    Directory of Open Access Journals (Sweden)

    Juliana Primo Basílio de Souza

    2015-06-01

    Full Text Available The thermomechanial properties of polymeric nanocom‐ posites are related to the quality of the adhesion between matrix and nanoparticle. Since the adhesion is related to the nature of the materials and the surface available for chemical, electrostatic and mechanical interactions among these materials, weak bonding forces between alumina (inorganic and polymer matrices (organic were expected. Furthermore, using nanoparticles with greater diameters means that the specific surface area reduction will have an adverse impact on the adhesive process. For epoxy matrices reinforced with alumina nanoparticles, different volume fractions and sizes were observed by differential scanning calorimetry (DSC: a relation between the glass transition temperature (Tg and the nanoparticle size. This observa‐ tion was tested by dynamic mechanical analysis (DMA and the cross-link density was calculated. In addition, the thermal stability enhanced by alumina addition to organic resins and the quality of the adhesion was observed by thermogravimetric analysis (TGA.

  16. TH-A-BRC-03: AAPM TG218: Measurement Methods and Tolerance Levels for Patient-Specific IMRT Verification QA

    Energy Technology Data Exchange (ETDEWEB)

    Miften, M. [University of Colorado School of Medicine (United States)

    2016-06-15

    of possible dosimetry protocols. The report will be reviewed by the AAPM Working Group on Recommendations for Radiotherapy External Beam Quality Assurance and then by the AAPM Science Council before publication in Medical Physics Survey of possible calibration protocols for calibration of Gamma Stereotactic Radiosurgery (GSR) devices Overview of modern Quality Assurance techniques for GSR AAPM TG-218 Tolerance Levels and Methodologies for IMRT Verification QA - Moyed Miften Patient-specific IMRT QA measurement is a process designed to identify discrepancies between calculated and delivered doses. Error tolerance limits are not well-defined or consistently applied across centers. The AAPM TG-218 report has been prepared to improve the understanding and consistency of this process by providing recommendations for methodologies and tolerance limits in patient-specific IMRT QA. Learning Objectives: Review measurement methods and methodologies for absolute dose verification Provide recommendations on delivery methods, data interpretation, the use of analysis routines and choice of tolerance limits for IMRT QA Sonja Dieterich has a research agreement with Sun Nuclear Inc. Steven Goetsch is a part-time consultant for Elekta.

  17. TH-A-BRC-03: AAPM TG218: Measurement Methods and Tolerance Levels for Patient-Specific IMRT Verification QA

    International Nuclear Information System (INIS)

    Miften, M.

    2016-01-01

    of possible dosimetry protocols. The report will be reviewed by the AAPM Working Group on Recommendations for Radiotherapy External Beam Quality Assurance and then by the AAPM Science Council before publication in Medical Physics Survey of possible calibration protocols for calibration of Gamma Stereotactic Radiosurgery (GSR) devices Overview of modern Quality Assurance techniques for GSR AAPM TG-218 Tolerance Levels and Methodologies for IMRT Verification QA - Moyed Miften Patient-specific IMRT QA measurement is a process designed to identify discrepancies between calculated and delivered doses. Error tolerance limits are not well-defined or consistently applied across centers. The AAPM TG-218 report has been prepared to improve the understanding and consistency of this process by providing recommendations for methodologies and tolerance limits in patient-specific IMRT QA. Learning Objectives: Review measurement methods and methodologies for absolute dose verification Provide recommendations on delivery methods, data interpretation, the use of analysis routines and choice of tolerance limits for IMRT QA Sonja Dieterich has a research agreement with Sun Nuclear Inc. Steven Goetsch is a part-time consultant for Elekta.

  18. Thought about ICRP TG84 report. What beyond it

    International Nuclear Information System (INIS)

    Niwa, Ohtsura

    2013-01-01

    Explained was the ICRP TG84 Report (Report of ICRP Task Group 84 on Initial Lessons Learned from the Nuclear Power Plant Accident in Japan vis-a-vis the ICRP System of Radiological Protection: Issues Identified from the NPP Accident in Japan and Recommendations to Improve the System of Radiation Protection; presented in October, 2012), together with author's thought about it. The Report contained 18 items and their related proposals: Inferring radiation risks (and the misunderstanding of nominal risk coefficients), Attributing radiation effects from low dose exposures, Quantifying radiation exposure, Assessing the importance of internal exposures, Managing emergency crisis, Protecting rescuers and volunteers, Responding with medical aid, Justifying necessary but disruptive protective actions, Transiting from an emergency to an existing situation, Rehabilitating evacuated areas, Categorizing public exposures due to an accident, Restricting individual doses of members of the public, Caring for infants and children, Considering pregnant women and their foetuses and embryos, Monitoring public protection, Dealing with 'contamination' of territories, rubble and residues, and consumer products, Recognizing the importance of psychological consequences, and Fostering the sharing of information. The Report also contained 11 Recommendations of actions for the Commission to take. The author had been installed as the Chair of Radiation Council in February, 2011, just before the Accident in March, and had had to concern the definition of various post-Accident dose limits in Japan, having had often faced the inefficiency of measures. He thought the ICRP protecting system was difficult to understand due to 2 reasons: one was that the system had been written aiming at experts of radiological protection and the other, that the system had been composed not only from science but also from an incorporated standard of social values, which resulted in inconsiderateness to the general

  19. GLUT4 expression in human muscle fibres is not correlated with intracellular triglyceride (TG) content. Is TG a maker or a marker of insulin resistance?

    DEFF Research Database (Denmark)

    Gaster, M; Ottosen, P D; Vach, W

    2003-01-01

    diabetic subjects, and young lean controls. TG density was significantly higher in slow compared to fast fibres in all studied subjects (pslow twitch fibres of obese diabetic subjects compared to obese (p...We have recently reported a progressive decline in the expression of glucose transporter isoform 4 (GLUT4) from control subjects through obese non-diabetics to obese type 2 diabetic subjects, indicating that the reduced GLUT4 in slow twitch fibres could be secondary to obesity. In this study we...... densities in slow and fast fibres did not correlate with the corresponding GLUT4 density in the same fibres in our study groups (p>0.05). Plasma TG and FFA did not correlate with GLUT4 expression in slow or fast fibres (p>0.05). In conclusion, TG content was increased in diabetic slow fibres with a reduced...

  20. A preliminary high-pressure thermogravimetric study of combustion reactivity of a Collie coal char

    Energy Technology Data Exchange (ETDEWEB)

    Chan, Yii Leng; Zhang, Zhezi; Zhu, Mingming; Zhang, Dongke [Western Australia Univ., Crawley, WA (Australia). Centre for Energy (M473); Luan, Chao [Western Australia Univ., Crawley, WA (Australia). Centre for Energy (M473); Tsinghua Univ., Beijing (China). Inst. of Thermal Engineering; You, Changfu [Tsinghua Univ., Beijing (China). Inst. of Thermal Engineering

    2013-07-01

    The effect of pressure(up to 20 bar)on the reactivity of a char(150-160 {mu}m) produced from Western Australian Collie coal has been studied using a high-pressure thermogravimetric analyser (HP TGA). The pressure demonstrated a positive effect in enhancing char combustion reactivities.Kinetic parameters have been determined from the experimental data.The apparent reaction order was found to be approximately 0.7 and the apparent activation energies were 91.0 kJ/mol at atmospheric pressure and 1.5 kJ/mol at an elevated pressure(10 bar),indicating a shift in the control regimes of the reaction at elevated pressures.The lumped effect of the sample size, bulk diffusion,interparticle and intraparticle diffusion at the elevated pressures played an important role in reducing the mass transfer during the HP-TGA experimentation.Thus the activation energy calculated at elevated pressures may not represent the intrinsic activation energy of the char particles but the apparent values of the bulk of the samples.

  1. Vaporization enthalpies of imidazolium based ionic liquids. A thermogravimetric study of the alkyl chain length dependence

    International Nuclear Information System (INIS)

    Verevkin, Sergey P.; Zaitsau, Dzmitry H.; Emel’yanenko, Vladimir N.; Ralys, Ricardas V.; Yermalayeu, Andrei V.; Schick, Christoph

    2012-01-01

    Highlights: ► Enthalpies of vaporization of ionic liquids were measured with thermogravimetry. ► We studied 1-alkyl-3-methyl-imidazolium bis(trifluoromethanesulfonyl)imide. ► The linear alkyl chain length was 4, 6, 8, 10, 12, 14, 16, and 18 C-atoms. ► A linear dependence on the chain length of the alkyl-imidazolium cation was found. - Abstract: Vaporization enthalpies for a series of ten ionic liquids (ILs) 1-alkyl-3-methyl-imidazolium bis(trifluoromethanesulfonyl)imide [C n mim][NTf 2 ], with the alkyl chain length n = 4, 6, 8, 10, 12, 14, 16, and 18 were determined using the thermogravimetric method. An internally consistent set of experimental data and vaporization enthalpies at 540 K was obtained. Vaporization enthalpies at 540 K have shown a linear dependence on the chain length of the alkyl-imidazolium cation in agreement with the experimental results measured previously with a quartz crystal microbalance. Ambiguity of Δ l g C pm o -values required for the extrapolation of experimental vaporization enthalpies to the reference temperature 298 K has been discussed.

  2. Thermogravimetric studies of high temperature reactions between potassium salts and chromium

    International Nuclear Information System (INIS)

    Lehmusto, J.; Lindberg, D.; Yrjas, P.; Skrifvars, B.-J.; Hupa, M.

    2012-01-01

    Highlights: ► K 2 CO 3 reacted with Cr 2 O 3 forming K 2 CrO 4 . ► Presence of chlorine did not alone explain the initiation of accelerated oxidation. ► More light was shed to the role of chromates in accelerated oxidation. ► Accelerated oxidation of chromia protected steels occurs in two consecutive stages. ► Both potassium and chloride are required, so that both stages of reaction occur. - Abstract: This study compares the high temperature reactions of potassium chloride (KCl) and potassium carbonate (K 2 CO 3 ), two salts found in fly ashes formed in biomass combustion, with both pure metallic chromium (Cr) and chromium oxide (Cr 2 O 3 ). The reactions were investigated with thermogravimetric measurements and the results discussed based on thermodynamic calculations. In simple terms: potassium chloride reacted with chromium forming potassium chromate (K 2 CrO 4 ) and chromium oxide. Potassium chloride did not react with chromium oxide. Potassium carbonate reacted with chromium oxide, but not with chromium. The presence of potassium is sufficient to initiate accelerated oxidation, but chloride is needed to sustain it.

  3. SU-E-I-20: Comprehensive Quality Assurance Test of Second Generation Toshiba Aquilion Large Bore CT Simulator Based On AAPM TG-66 Recommendations

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, D [Toshiba America Medical Systems, Tustin, CA (United States)

    2015-06-15

    Purpose: AAPM radiation therapy committee task group No. 66 (TG-66) published a report which described a general approach to CT simulator QA. The report outlines the testing procedures and specifications for the evaluation of patient dose, radiation safety, electromechanical components, and image quality for a CT simulator. The purpose of this study is to thoroughly evaluate the performance of a second generation Toshiba Aquilion Large Bore CT simulator with 90 cm bore size (Toshiba, Nasu, JP) based on the TG-66 criteria. The testing procedures and results from this study provide baselines for a routine QA program. Methods: Different measurements and analysis were performed including CTDIvol measurements, alignment and orientation of gantry lasers, orientation of the tabletop with respect to the imaging plane, table movement and indexing accuracy, Scanogram location accuracy, high contrast spatial resolution, low contrast resolution, field uniformity, CT number accuracy, mA linearity and mA reproducibility using a number of different phantoms and measuring devices, such as CTDI phantom, ACR image quality phantom, TG-66 laser QA phantom, pencil ion chamber (Fluke Victoreen) and electrometer (RTI Solidose 400). Results: The CTDI measurements were within 20% of the console displayed values. The alignment and orientation for both gantry laser and tabletop, as well as the table movement and indexing and scanogram location accuracy were within 2mm as specified in TG66. The spatial resolution, low contrast resolution, field uniformity and CT number accuracy were all within ACR’s recommended limits. The mA linearity and reproducibility were both well below the TG66 threshold. Conclusion: The 90 cm bore size second generation Toshiba Aquilion Large Bore CT simulator that comes with 70 cm true FOV can consistently meet various clinical needs. The results demonstrated that this simulator complies with the TG-66 protocol in all aspects including electromechanical component

  4. Download - Open TG-GATEs | LSDB Archive [Life Science Database Archive metadata

    Lifescience Database Archive (English)

    Full Text Available switchLanguage; BLAST Search Image Search Home About Archive Update History Data ...Download License Update History of This Database Site Policy | Contact Us Download - Open TG-GATEs | LSDB Archive ...

  5. Database Description - Open TG-GATEs | LSDB Archive [Life Science Database Archive metadata

    Lifescience Database Archive (English)

    Full Text Available ne expression data and predict the safety of candidate chemicals has been develop...ears of the project, more than 30 safety biomarkers were develped by using TG-GATEs. In addition, data acqui

  6. Differences Between Tg2576 and Wild Type Mice in the NMDA Receptor-Nitric Oxide Pathway After Prolonged Application of a Diet High in Advanced Glycation End Products.

    Science.gov (United States)

    Kristofikova, Zdena; Ricny, Jan; Sirova, Jana; Ripova, Daniela; Lubitz, Irit; Schnaider-Beeri, Michal

    2015-08-01

    It has been suggested that advanced glycation end (AGE) products, via cognate receptor activation, are implicated in several diseases, including Alzheimer's disease. The NMDA receptor-nitric oxide pathway appears to be influenced by AGE products and involved in the pathogenesis of this type of dementia. In this study, C57BL/6J (WT) and transgenic (Tg2576) mice expressing human mutant amyloid precursor protein were kept on prolonged (8 months) diets containing regular or high amounts of AGE products. After the decapitation of 11-months old mice, brain tissue analyses were performed [expressions of the NR1, NR2A and NR2B subunits of NMDA receptors, activities of neuronal, endothelial and inducible nitric oxide synthase (nNOS, eNOS and iNOS)]. Moreover, levels of malondialdehyde and of human amyloid β 1-42 were estimated. We found increased activity of nNOS in WT mice maintained on a high compared to regular AGE diet; however, no similar differences were found in Tg2576 mice. In addition, we observed an increase in NR1 expression in Tg2576 compared to WT mice, both kept on a diet high in AGE products. Correlation analyses performed on mice kept on the regular AGE diet supported close links between particular subunits (NR2A-NR2B, in WT as well as in Tg2576 mice), between subunits and synthase (NR2A/NR2B-nNOS, only in WT mice) or between particular synthases (nNOS-iNOS, only in WT). Correlation analysis also revealed differences between WT mice kept on both diets (changed correlations between NR2A/NR2B-nNOS, between nNOS-eNOS and between eNOS-iNOS). Malondialdehyde levels were increased in both Tg2576 groups when compared to the corresponding WT mice, but no effects of the diets were observed. Analogously, no significant effects of diets were found in the levels of soluble or insoluble amyloid β 1-42 in Tg2576 mice. Our results demonstrate that prolonged ingestion of AGE products can influence the NMDA receptor-nitric oxide pathway in the brain and that only WT mice

  7. Notes on the implementation of the TG-43 formalism in high-rate brachytherapy; Notas sobre la implementacion del formalismo TG-43 en braquiterapia de lata tasa

    Energy Technology Data Exchange (ETDEWEB)

    Sendon del Rio, J. R.; Gonzalez Ruiz, C.; Garcia Marcos, R.; Jimenez Rojas, R.; Lopez Bote, M. A.

    2011-07-01

    The TG-43 formalism is based on dosimetric parameters depend on the specific font design extracted from dose distributions calculated by Monte Carlo in water. Relatively easy to implement, yet provides a degree of uncertainty, making it necessary to verify the calculation algorithm in the planning system to assess its behavior.

  8. Determinação da espessura da camada polimérica de fases estacionárias imobilizadas para cromatografia líquida de alta eficiência por termogravimetria Determination of polymeric layer thickness on immobilized stationary phases for high-performance liquid chromatography using thermogravimetric analyses

    Directory of Open Access Journals (Sweden)

    Anizio M. Faria

    2008-01-01

    Full Text Available This paper presents a simple and practical thermogravimetric method for determining the layer thickness of immobilized polymer stationary phases used in reversed-phase high-performance liquid chromatography. In this method, the weight loss of different polysiloxanes immobilized onto chromatographic supports, determined over the temperature range 150-650 ºC, demonstrated excellent agreement with the sum of carbon and hydrogen content obtained by elemental analysis. The results presented here suggest that the thermogravimetric procedure is an accurate and precise method to determine the polymeric material content on polymer-coated stationary phases.

  9. Relationship TG/HDL-C and insulin resistance in adult women by nutritional status

    Directory of Open Access Journals (Sweden)

    Lorena Belén

    2014-04-01

    Full Text Available Introduction: The ratio assessment TG/HDL-C is an indicator of LDL size, facilitating the detection of individuals with increased atherogenic risk. Estimating the size of the LDL becomes important, especially in patients with TG values near the upper limit of normal values of reference and HDL-C. The objective of the study is to estimate the association between TG/HDL-C and insulin resistance (IR by nutritional status in adult women attending the Foundation for Endocrine Metabolic Diseases Research and Applied Clinical Research (FIEEM.Material and methods: Design Cross-sectional, non-pregnant adult women, apparently healthy, older than 30 years old, attending FIEEM in the Autonomous City of Buenos Aires. Dependent variable: TG/HDL-C ≥ 3.0 considered high value. Independent variables: IR by homeostatic model index HOMA-IR ≥ 2.5 categorizing the sample into two groups: with and without IR, and controlled by nutritional status using body mass index (BMI and waist circumference (CC. SPSS Statistics 15.0, calculating X2 or Fisher exact test, OR with confidence intervals of 95% and establishing logistic regression p value < 0.05.Results: We evaluated a purposive sample of 104 women (31.4% and 26% IR with TG/HDL-C high. 84.6% were overweight or obese and 88.5% increased CC. Women with BMI had significantly increased 0.15-fold increased risk (95% CI = 0.01 to 1.26 for TG/HDL-C high (p = 0.04 than the control women. There was no significance with increased CC. The ratio TG/HDL-C high IR was significantly correlated (r = 0.30 p = 0.002.Conclusions: Body weight was significantly associated with IR and the ratio TG/HDL-C increased. This ratio correlated significantly with IR in apparently healthy women.

  10. Thermogravimetric measurement of hydrogen storage in carbon-based materials: promise and pitfalls

    International Nuclear Information System (INIS)

    Pinkerton, F.E.; Wicke, B.G.; Olk, C.H.; Tibbetts, G.G.; Meisner, G.P.; Meyer, M.S.; Herbst, J.F.

    2000-01-01

    We have used a thermogravimetric analyzer (TGA) to measure the hydrogen absorption capacity of a variety of carbon-based storage materials, including Li- and K-intercalated graphite and Li-doped multi-wall nanotubes. The TGA uses weight gain/loss as a function of time and temperature to monitor hydrogen absorption/desorption in flowing hydrogen gas. Creating and maintaining a contaminant-free atmosphere is critical to the accurate TGA measurement of hydrogen absorption in carbon-based materials; even low concentrations of impurity gases such as O 2 or H 2 O are sufficient to masquerade as hydrogen absorption. We will discuss examples of this effect relevant to recent reports of hydrogen storage appearing in the literature. The precautions required are non-trivial. In our TGA, for instance, about 16% of the original atmosphere remains after a two-hour purge; at least 15 hours is required to fully purge the apparatus. Furthermore, we cover the TGA with a protective atmosphere enclosure during sample loading to minimize the introduction of impurity gases. With these precautions it is possible to unambiguously measure hydrogen storage. For example, we have determined the hydrogen absorption capacity of our K-intercalated graphite samples to be 1.3 wt% total hydrogen absorption above 50 o C, of which 0.2 wt% can be reproducibly recovered with temperature cycling. With due care, TGA measurements provide complementary information to that obtained from standard pressure techniques for measuring hydrogen sorption, which rely on measuring the loss of gas pressure in a known volume. Taken together, TGA and pressure measurements provide a powerful combination for determining verifiable hydrogen storage capacity. (author)

  11. Thermogravimetric pyrolysis kinetics of bamboo waste via Asymmetric Double Sigmoidal (Asym2sig) function deconvolution.

    Science.gov (United States)

    Chen, Chuihan; Miao, Wei; Zhou, Cheng; Wu, Hongjuan

    2017-02-01

    Thermogravimetric kinetic of bamboo waste (BW) pyrolysis has been studied using Asymmetric Double Sigmoidal (Asym2sig) function deconvolution. Through deconvolution, BW pyrolytic profiles could be separated into three reactions well, each of which corresponded to pseudo hemicelluloses (P-HC), pseudo cellulose (P-CL), and pseudo lignin (P-LG) decomposition. Based on Friedman method, apparent activation energy of P-HC, P-CL, P-LG was found to be 175.6kJ/mol, 199.7kJ/mol, and 158.4kJ/mol, respectively. Energy compensation effects (lnk 0, z vs. E z ) of pseudo components were in well linearity, from which pre-exponential factors (k 0 ) were determined as 6.22E+11s -1 (P-HC), 4.50E+14s -1 (P-CL) and 1.3E+10s -1 (P-LG). Integral master-plots results showed pyrolytic mechanism of P-HC, P-CL, and P-LG was reaction order of f(α)=(1-α) 2 , f(α)=1-α and f(α)=(1-α) n (n=6-8), respectively. Mechanism of P-HC and P-CL could be further reconstructed to n-th order Avrami-Erofeyev model of f(α)=0.62(1-α)[-ln(1-α)] -0.61 (n=0.62) and f(α)=1.08(1-α)[-ln(1-α)] 0.074 (n=1.08). Two-steps reaction was more suitable for P-LG pyrolysis. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Thermal Analysis of Braille Formed by Using Screen Printing and Inks with Thermo Powder

    Directory of Open Access Journals (Sweden)

    Svіtlana HAVENKO

    2015-03-01

    Full Text Available In order to improve the integration of blind people into society, suitable conditions should be provided for them. The expansion of Braille (BR use could serve the purpose. Depending on the materials used for Braille, it can be formed or printed in different ways: embossing, screen printing, thermoforming, digital printing. The aim of this research is to determine the effect of thermal properties of screen printing inks and inks with thermo-powder on the qualitative parameters of Braille. Screen printing inks and inks with thermo-powder were chosen for the research. Carrying out the qualitative analysis of printouts with Braille, the thermal stability was evaluated by analyzing the thermograms obtained with derivatograph Q-1500. This paper presents the findings of the thermogravimetric (TG, differential thermogravimetric (DTG and differential thermal analysis (DTA of printouts printed on paperboard Plike and using traditional screen printing inks and screen printing inks with thermo-powder. Based on the testing findings it is determined that thermal stability of printouts printed with thermo-powder ink is higher than printed with screen printing inks. It is determined that the appropriate temperature range of screen printing inks with thermo-powder drying is 98 ºC – 198 ºC because in this case better relief of Braille dots is obtained.DOI: http://dx.doi.org/10.5755/j01.ms.21.1.5702

  13. SU-E-T-127: Application of TG-119 for Evaluation of Proton Spot Scanning Based Planning and Treatment Delivery

    Energy Technology Data Exchange (ETDEWEB)

    Saini, J; Cao, N; Wong, T [SCCA Proton Therapy, A Procure Center, Seattle, WA (United States); Bowen, S; Bloch, C [University of Washington, School of Medicine, Seattle, WA (United States)

    2015-06-15

    Purpose: The clinical test cases presented in AAPM TG-119 are used to evaluate the accuracy of treatment planning and delivery through spot scanning proton beams. Methods: An IBA spot scanning delivery system has been commissioned to be used with the RayStation treatment planning system. Various test cases provided in TG-119 were used for planning and delivery verification. The CT dataset and structures as provided by TG-119 were imported into a mock patient. The plans were optimized using the multi field optimization (MFO) to achieve the desired goals. The planner was given the flexibility to achieve the given dose-volume goals by creating appropriate objectives and constraints. Beams were delivered to a phantom and measurements were performed at multiple depths using the MatrixxPT detector array. The analyses were performed on beam by beam basis and quantified using the gamma index. A tolerance of 3%/3 mm in 2D was used for gamma index analysis along with dose threshold of 10%. Results: The clinical goals for targets and critical structures were met or improved for all cases except the C-Shape target with difficult constraints. The minimum gamma index using the 3%/3mm as a criterion is 93.3% for one of the planes measured for C-Shape target. Using 2%/2mm as a criterion, the minimum gamma index drops to 70%. Only Prostate target has all the planes above >90% pass using the 2%/2mm criterion. Conclusion: The overall accuracy of the treatment planning and delivery is deemed clinically acceptable. The test cases with highly modulated beams can have steep gradients in the dose profiles that can reduce the gamma index pass rate. Gamma analysis based on 3D data may be needed for routine use of 2%/2mm criterion. In addition, improvements in modelling of spot profiles in dose engine may be required for further improving the gamma index pass rate.

  14. Assessment of display performance for medical imaging systems: Executive summary of AAPM TG18 report

    International Nuclear Information System (INIS)

    Samei, Ehsan; Badano, Aldo; Chakraborty, Dev

    2005-01-01

    Digital imaging provides an effective means to electronically acquire, archive, distribute, and view medical images. Medical imaging display stations are an integral part of these operations. Therefore, it is vitally important to assure that electronic display devices do not compromise image quality and ultimately patient care. The AAPM Task Group 18 (TG18) recently published guidelines and acceptance criteria for acceptance testing and quality control of medical display devices. This paper is an executive summary of the TG18 report. TG18 guidelines include visual, quantitative, and advanced testing methodologies for primary and secondary class display devices. The characteristics, tested in conjunction with specially designed test patterns (i.e., TG18 patterns), include reflection, geometric distortion, luminance, the spatial and angular dependencies of luminance, resolution, noise, glare, chromaticity, and display artifacts. Geometric distortions are evaluated by linear measurements of the TG18-QC test pattern, which should render distortion coefficients less than 2%/5% for primary/secondary displays, respectively. Reflection measurements include specular and diffuse reflection coefficients from which the maximum allowable ambient lighting is determined such that contrast degradation due to display reflection remains below a 20% limit and the level of ambient luminance (L amb ) does not unduly compromise luminance ratio (LR) and contrast at low luminance levels. Luminance evaluation relies on visual assessment of low contrast features in the TG18-CT and TG18-MP test patterns, or quantitative measurements at 18 distinct luminance levels of the TG18-LN test patterns. The major acceptable criteria for primary/secondary displays are maximum luminance of greater than 170/100 cd/m 2 , LR of greater than 250/100, and contrast conformance to that of the grayscale standard display function (GSDF) of better than 10%/20%, respectively. The angular response is tested to

  15. Thermogravimetric control of intermediate compounds in uranium metallurgy; Control termogravimetrico de productos intermedios de la metalurgia del uranio

    Energy Technology Data Exchange (ETDEWEB)

    Gasco Sanchez, L; Fernandez Cellini, R

    1959-07-01

    The thermal decomposition of some intermediate compounds in the metallurgy of the uranium as uranium peroxide, ammonium uranate, uranium and ammonium penta-fluoride, uranium tetrafluoride and uranous oxide has been study by means of the Chevenard's thermo balance. Some data on pyrolysis of synthetic mixtures of intermediate compounds which may occasionally appear during the industrial process, are given. Thermogravimetric methods of control are suggested, usable in interesting products in the uranium metallurgy. (Author) 20 refs.

  16. Thermogravimetric control of intermediate compounds in uranium metallurgy; Control termogravimetrico de productos intermedios de la metalurgia del uranio

    Energy Technology Data Exchange (ETDEWEB)

    Gasco Sanchez, L.; Fernandez Cellini, R.

    1959-07-01

    The thermal decomposition of some intermediate compounds in the metallurgy of the uranium as uranium peroxide, ammonium uranate, uranium and ammonium penta-fluoride, uranium tetrafluoride and uranous oxide has been study by means of the Chevenard's thermo balance. Some data on pyrolysis of synthetic mixtures of intermediate compounds which may occasionally appear during the industrial process, are given. Thermogravimetric methods of control are suggested, usable in interesting products in the uranium metallurgy. (Author) 20 refs.

  17. Tissue transglutaminase (TG-2) modified amniotic membrane: a novel scaffold for biomedical applications

    International Nuclear Information System (INIS)

    Chau, David Y S; Brown, Sheridan V; Ghaemmaghami, Amir M; Mather, Melissa L; Hutter, Victoria; Tint, Naing L; Rose, Felicity R A J; Dua, Harminder S

    2012-01-01

    The amniotic membrane (AM) is considered as a natural cell culture substrate and has occasionally been exploited in regenerative medicine especially for ocular surface reconstruction and dermal wound healing applications. However, its use is limited by its relatively weak mechanical strength, difficulty during manual handling and susceptibility to proteolytic degradation in vivo. Therefore, in this study we aimed to enhance the mechanical and biological characteristics of the AM by enzymatically cross-linking it using tissue transglutaminase (TG)—a calcium-dependent enzyme capable of forming stable ε(γ-glutamyl)lysine cross-linkages. Using a biological catalyst such as TG does not only prevent denaturation during sample preparation but also minimizes the potential of residual chemical cross-linking agents compared to alternative methodologies. Human AM, sourced from elective caesarean sectioning, were treated with TG, bovine serum albumin and/or a no-treatment control. Samples were then compared in terms of their physical and (scanning electron microscopy (SEM), transparency, mechanical strength, susceptibility to proteolytic degradation) biological characteristics (in vitro cell culture, activation of dendritic cells (DC)) and their in vivo biocompatibility/angiogenic capacity (chick chorioallantoic membrane assay). TG-treated AM exhibited enhanced mechanical strength and greater resistance to proteolytic/collagenase degradation compared to the control(s). SEM imaging of the TG-treated membrane summarized a significantly closer association and greater interconnectivity of individual collagen fibres yet it had no effect on the overall transparency of the AM. In vitro cell culture demonstrated no detrimental effect of TG-treatment on the AM in terms of cell attachment, spreading, proliferation and differentiation. Moreover, an ‘immune response’ was not elicited based on extended in vitro culture with human-monocyte-derived DC. Interestingly, the TG

  18. Characteristic Study of Shenmu Bituminous Coal Combustion with Online TG-MS-FTIR

    Science.gov (United States)

    Pan, Guanfu

    2018-01-01

    The combustion characteristics of Shenmu bituminous pulverized coal (SBC) were comprehensively investigated with a combined TG-MS-FTIR system by considering the effect of particle size, heating rate and total flowrate. The combustion products were accurately quantified by normalization and numerical analysis of MS results. The results indicate that the decrease of the particle size, heating rate and total flowrate result in lower ignition and burnout temperatures. The activation energy tends to be lower with smaller particle size, lower heating rate and total flowrate. The MS and FTIR results demonstrate that lower concentrations of different products, such as NO, NO2, HCN, CH4 and SO2 were produced with smaller particle size, slower heating rate and lower total flowrate. The decrease of particle size would lead to more contact area with oxygen and slower heating rate could provide more sufficient time for the diffusion. High total flowrate would reduce the oxygen adsorbability on the coal particle surface and shorten the residence time of oxygen, which makes the ignition difficult to occur. This work will guide to understand the combustion kinetics of pulverized coals and be beneficial to control the formation of pollutants.

  19. Insulin receptor in mouse neuroblastoma cell line N18TG2: binding properties and visualization with colloidal gold.

    Science.gov (United States)

    Sartori, C; Stefanini, S; Bernardo, A; Augusti-Tocco, G

    1992-08-01

    Insulin function in the nervous system is still poorly understood. Possible roles as a neuromodulator and as a growth factor have been proposed (Baskin et al., 1987, Ann. Rev. Physiol. 49, 335-347). Stable cell lines may provide an appropriate experimental system for the analysis of insulin action on the various cellular components of the central nervous system. We report here a study to investigate the presence and the properties of insulin specific binding sites in the murine neuroblastoma line, N18TG2, together with insulin action on cell growth and metabolism. Also, receptor internalization has been studied. Binding experiments, carried out in standard conditions at 20 degrees C, enabled us to demonstrate that these cells bind insulin in a specific manner, thus confirming previous findings on other cell lines. Saturation curves showed the presence of two binding sites with Kd 0.3 and 9.7 nM. Competition experiments with porcine and bovine insulin showed an IC50 of 1 and 10 nM, respectively. Competition did not occur in the presence of the unrelated hormones ACTH and FSH. Dissociation experiments indicated the existence of an internalization process of the ligand-receptor complex; this was confirmed by an ultrastructural study using gold conjugated insulin. As far as the insulin action in N18TG2 cells is concerned, physiological concentrations stimulate cell proliferation, whereas no stimulation of glucose uptake was observed, indicating that insulin action in these cells is not mediated by general metabolic effects. On the basis of these data, N18TG2 line appears to be a very suitable model for further studies of the neuronal type insulin receptors, and possibly insulin specific action on the nervous system.

  20. Ocular changes in TgF344-AD rat model of Alzheimer's disease.

    Science.gov (United States)

    Tsai, Yuchun; Lu, Bin; Ljubimov, Alexander V; Girman, Sergey; Ross-Cisneros, Fred N; Sadun, Alfredo A; Svendsen, Clive N; Cohen, Robert M; Wang, Shaomei

    2014-01-29

    Alzheimer's disease (AD) is the most common neurodegenerative disorder characterized by progressive decline in learning, memory, and executive functions. In addition to cognitive and behavioral deficits, vision disturbances have been reported in early stage of AD, well before the diagnosis is clearly established. To further investigate ocular abnormalities, a novel AD transgenic rat model was analyzed. Transgenic (Tg) rats (TgF344-AD) heterozygous for human mutant APPswe/PS1ΔE9 and age-matched wild type (WT) rats, as well as 20 human postmortem retinal samples from both AD and healthy donors were used. Visual function in the rodent was analyzed using the optokinetic response and luminance threshold recording from the superior colliculus. Immunohistochemistry on retinal and brain sections was used to detect various markers including amyloid-β (Aβ) plaques. As expected, Aβ plaques were detected in the hippocampus, cortex, and retina of Tg rats. Plaque-like structures were also found in two AD human whole-mount retinas. The choroidal thickness was significantly reduced in both Tg rat and in AD human eyes when compared with age-matched controls. Tg rat eyes also showed hypertrophic retinal pigment epithelial cells, inflammatory cells, and upregulation of complement factor C3. Although visual acuity was lower in Tg than in WT rats, there was no significant difference in the retinal ganglion cell number and retinal vasculature. In this study, we observed pathological changes in the choroid and in RPE cells in the TgF344-AD rat model; choroidal thinning was observed further in human AD retina. Along with Ab deposition, the inflammatory response was manifested by microglial recruitment and complement activation. Further studies are needed to elucidate the significance and mechanisms of these pathological changes [corrected].

  1. Spaceflight influences both mucosal and peripheral cytokine production in PTN-Tg and wild type mice.

    Directory of Open Access Journals (Sweden)

    Justin L McCarville

    Full Text Available Spaceflight is associated with several health issues including diminished immune efficiency. Effects of long-term spaceflight on selected immune parameters of wild type (Wt and transgenic mice over-expressing pleiotrophin under the human bone-specific osteocalcin promoter (PTN-Tg were examined using the novel Mouse Drawer System (MDS aboard the International Space Station (ISS over a 91 day period. Effects of this long duration flight on PTN-Tg and Wt mice were determined in comparison to ground controls and vivarium-housed PTN-Tg and Wt mice. Levels of interleukin-2 (IL-2 and transforming growth factor-beta1 (TGF-β1 were measured in mucosal and systemic tissues of Wt and PTN-Tg mice. Colonic contents were also analyzed to assess potential effects on the gut microbiota, although no firm conclusions could be made due to constraints imposed by the MDS payload and the time of sampling. Spaceflight-associated differences were observed in colonic tissue and systemic lymph node levels of IL-2 and TGF-β1 relative to ground controls. Total colonic TGF-β1 levels were lower in Wt and PTN-Tg flight mice in comparison to ground controls. The Wt flight mouse had lower levels of IL-2 and TGF-β1 compared to the Wt ground control in both the inguinal and brachial lymph nodes, however this pattern was not consistently observed in PTN-Tg mice. Vivarium-housed Wt controls had higher levels of active TGF-β1 and IL-2 in inguinal lymph nodes relative to PTN-Tg mice. The results of this study suggest compartmentalized effects of spaceflight and on immune parameters in mice.

  2. A Novel Form of Compensation in the Tg2576 Amyloid Mouse Model of Alzheimer's Disease.

    Science.gov (United States)

    Somogyi, Attila; Katonai, Zoltán; Alpár, Alán; Wolf, Ervin

    2016-01-01

    One century after its first description, pathology of Alzheimer's disease (AD) is still poorly understood. Amyloid-related dendritic atrophy and membrane alterations of susceptible brain neurons in AD, and in animal models of AD are widely recognized. However, little effort has been made to study the potential effects of combined morphological and membrane alterations on signal transfer and synaptic integration in neurons that build up affected neural networks in AD. In this study spatial reconstructions and electrophysiological measurements of layer II/III pyramidal neurons of the somatosensory cortex from wild-type (WT) and transgenic (TG) human amyloid precursor protein (hAPP) overexpressing Tg2576 mice were used to build faithful segmental cable models of these neurons. Local synaptic activities were simulated in various points of the dendritic arbors and properties of subthreshold dendritic impulse propagation and predictors of synaptic input pattern recognition ability were quantified and compared in modeled WT and TG neurons. Despite the widespread dendritic degeneration and membrane alterations in mutant mouse neurons, surprisingly little, or no change was detected in steady-state and 50 Hz sinusoidal voltage transfers, current transfers, and local and propagation delays of PSPs traveling along dendrites of TG neurons. Synaptic input pattern recognition ability was also predicted to be unaltered in TG neurons in two different soma-dendritic membrane models investigated. Our simulations predict the way how subthreshold dendritic signaling and pattern recognition are preserved in TG neurons: amyloid-related membrane alterations compensate for the pathological effects that dendritic atrophy has on subthreshold dendritic signal transfer and integration in layer II/III somatosensory neurons of this hAPP mouse model for AD. Since neither propagation of single PSPs nor integration of multiple PSPs (pattern recognition) changes in TG neurons, we conclude that AD

  3. Analysis of briquetting process of sewage sludge with coal to combustion process

    Directory of Open Access Journals (Sweden)

    Kosturkiewicz Bogdan

    2016-01-01

    Full Text Available Energy recovery from sewage sludge can be achieved by several thermal technologies, but before those processes sewage sludge requires special pretreatment. The paper presents the investigation of the sewage sludge with coal briquettes as a fuel for combustion process. Research is conducted at Department of Manufacturing Systems and Department of Thermal Engineering and Environmental Protection, AGH University of Science and Technology to develop a technology of briquette preparation. The obtained results showed possibility of briquetting of municipal sewage sludge with coal in roll presses, equipped with asymmetric thickening gravity feed system. The following properties were determined for the obtained briquettes: density, drop strength and compressive strength. Based on physical and chemical analysis of prepared briquettes it was confirmed that briquettes have good fuel properties to combustion process. Thermal behaviour of studied sewage sludge and prepared mixture was investigated by thermogravimetric analysis (TG. For the thermo gravimetric analysis (TG the samples were heated in an alumina crucible from an ambient temperature up to 1000 °C at a constant rates: 10 °C/min, 40 °C/min and 100 °C/min in a 40 ml/min flow of air.

  4. SU-E-T-87: A TG-100 Approach for Quality Improvement of Associated Dosimetry Equipment

    Energy Technology Data Exchange (ETDEWEB)

    Manger, R; Pawlicki, T; Kim, G [UCSD Medical Center, La Jolla, CA (United States)

    2015-06-15

    Purpose: Dosimetry protocols devote so much time to the discussion of ionization chamber choice, use and performance that is easy to forget about the importance of the associated dosimetry equipment (ADE) in radiation dosimetry - barometer, thermometer, electrometer, phantoms, triaxial cables, etc. Improper use and inaccuracy of these devices may significantly affect the accuracy of radiation dosimetry. The purpose of this study is to evaluate the risk factors in the monthly output dosimetry procedure and recommend corrective actions using a TG-100 approach. Methods: A failure mode and effects analysis (FMEA) of the monthly linac output check procedure was performed to determine which steps and failure modes carried the greatest risk. In addition, a fault tree analysis (FTA) was performed to expand the initial list of failure modes making sure that none were overlooked. After determining the failure modes with the highest risk priority numbers (RPNs), 11 physicists were asked to score corrective actions based on their ease of implementation and potential impact. The results were aggregated into an impact map to determine the implementable corrective actions. Results: Three of the top five failure modes were related to the thermometer and barometer. The two highest RPN-ranked failure modes were related to barometric pressure inaccuracy due to their high lack-of-detectability scores. Six corrective actions were proposed to address barometric pressure inaccuracy, and the survey results found the following two corrective actions to be implementable: 1) send the barometer for recalibration at a calibration laboratory and 2) check the barometer accuracy against the local airport and correct for elevation. Conclusion: An FMEA on monthly output measurements displayed the importance of ADE for accurate radiation dosimetry. When brainstorming for corrective actions, an impact map is helpful for visualizing the overall impact versus the ease of implementation.

  5. Tissue transglutaminase (TG2) is involved in the resistance of cancer cells to the histone deacetylase (HDAC) inhibitor vorinostat.

    Science.gov (United States)

    Carbone, Carmine; Di Gennaro, Elena; Piro, Geny; Milone, Maria Rita; Pucci, Biagio; Caraglia, Michele; Budillon, Alfredo

    2017-03-01

    Vorinostat demonstrated preclinical and clinical efficacy in human cancers and is the first histone deacetylase inhibitor (HDACi) approved for cancer treatment. Tissue transglutaminase (TG2) is a multifunctional enzyme that catalyzes a Ca 2+ dependent transamidating reaction resulting in covalent cross-links between proteins. TG2 acts also as G-protein in trans-membrane signaling and as a cell surface adhesion mediator. TG2 up-regulation has been demonstrated in several cancers and its expression levels correlate with resistance to chemotherapy and metastatic potential. We demonstrated that the anti-proliferative effect of the HDACi vorinostat is paralleled by the induction of TG2 mRNA and protein expression in cancer cells but not in ex vivo treated peripheral blood lymphocytes. This effect was also shared by other pan-HDACi and resulted in increased TG2 transamidating activity. Notably, high TG2 basal levels in a panel of cancer cell lines correlated with lower vorinostat antiproliferative activity. Notably, in TG2-knockdown cancer cells vorinostat anti-proliferative and pro-apoptotic effects were enhanced, whereas in TG2-full-length transfected cells were impaired, suggesting that TG2 could represent a mechanism of intrinsic or acquired resistance to vorinostat. In fact, co-treatment of tumor cells with inhibitors of TG2 transamidating activity potentiated the antitumor effect of vorinostat. Moreover, vorinostat-resistant MCF7 cells selected by stepwise increasing concentrations of the drug, significantly overexpressed TG2 protein compared to parental cells, and co-treatment of these cells with TG2 inhibitors reversed vorinostat-resistance. Taken together, our data demonstrated that TG2 is involved in the resistance of cancer cells to vorinostat, as well as to other HDACi.

  6. Morphological Changes of Limestone Sorbent Particles during Carbonation/Calcination Looping Cycles in a Thermogravimetric Analyzer (TGA) and Reactivation with Steam

    KAUST Repository

    Wu, Y.; Blamey, J.; Anthony, E. J.; Fennell, P. S.

    2010-01-01

    Carbonation and calcination looping cycles were carried out on four limestones in a thermogravimetric analyzer (TGA). The CO2 carrying capacity of a limestone particle decays very quickly in the first 10 cycles, reducing to about 20% of its original

  7. Thermogravimetric and calorimetric characteristics during co-pyrolysis of municipal solid waste components.

    Science.gov (United States)

    Ansah, Emmanuel; Wang, Lijun; Shahbazi, Abolghasem

    2016-10-01

    The thermogravimetric and calorimetric characteristics during pyrolysis of wood, paper, textile and polyethylene terephthalate (PET) plastic in municipal solid wastes (MSW), and co-pyrolysis of biomass-derived and plastic components with and without torrefaction were investigated. The active pyrolysis of the PET plastic occurred at a much higher temperature range between 360°C and 480°C than 220-380°C for the biomass derived components. The plastic pyrolyzed at a heating rate of 10°C/min had the highest maximum weight loss rate of 18.5wt%/min occurred at 420°C, followed by 10.8wt%/min at 340°C for both paper and textile, and 9.9wt%/min at 360°C for wood. At the end of the active pyrolysis stage, the final mass of paper, wood, textile and PET was 28.77%, 26.78%, 21.62% and 18.31%, respectively. During pyrolysis of individual MSW components at 500°C, the wood required the least amount of heat at 665.2J/g, compared to 2483.2J/g for textile, 2059.4J/g for paper and 2256.1J/g for PET plastic. The PET plastic had much higher activation energy of 181.86kJ/mol, compared to 41.47kJ/mol for wood, 50.01kJ/mol for paper and 36.65kJ/mol for textile during pyrolysis at a heating rate of 10°C/min. H2O and H2 peaks were observed on the MS curves for the pyrolysis of three biomass-derived materials but there was no obvious H2O and H2 peaks on the MS curves of PET plastic. There was a significant interaction between biomass and PET plastic during co-pyrolysis if the biomass fraction was dominant. The amount of heat required for the co-pyrolysis of the biomass and plastic mixture increased with the increase of plastic mass fraction in the mixture. Torrefaction at a proper temperature and time could improve the grindability of PET plastic. The increase of torrefaction temperature and time did not affect the temperature where the maximum pyrolytic rates occurred for both biomass and plastic but decreased the maximum pyrolysis rate of biomass and increased the maximum pyrolysis

  8. High-Tg TOPAS mPOF strain sensing at 110 degrees

    DEFF Research Database (Denmark)

    Nielsen, Kristian; Markos, Christos; Stefani, Alessio

    2013-01-01

    We demonstrate a mPOF made of high-Tg TOPAS grade 5013 with Tg = 135°C. We inscribe FBGs into the fiber and demonstrate strain sensing of 2.5% strain at 98°C, further we also demonstrate strain sensing at a record high temperature of 110°C. The Bragg wavelengths of the FBGs are around 860 nm, whe...... the propagation loss is 5.1dB/m, close to the fiber loss minimum of 3.67dB/m at 787nm....

  9. FPGA Implementation of Burst-Mode Synchronization for SOQSPK-TG

    Science.gov (United States)

    2014-06-01

    is normalized to π. The proposed burst-mode architecture is written in VHDL and verified using Modelsim. The VHDL design is implemented on a Xilinx...Document Number: SET 2014-0043 412TW-PA-14298 FPGA Implementation of Burst-Mode Synchronization for SOQSPK-TG June 2014 Final Report Test...To) 9/11 -- 8/14 4. TITLE AND SUBTITLE FPGA Implementation of Burst-Mode Synchronization for SOQSPK-TG 5a. CONTRACT NUMBER: W900KK-11-C-0032 5b

  10. Database Description - Open TG-GATEs Pathological Image Database | LSDB Archive [Life Science Database Archive metadata

    Lifescience Database Archive (English)

    Full Text Available List Contact us Open TG-GATEs Pathological Image Database Database Description General information of database Database... name Open TG-GATEs Pathological Image Database Alternative name - DOI 10.18908/lsdba.nbdc00954-0...iomedical Innovation 7-6-8, Saito-asagi, Ibaraki-city, Osaka 567-0085, Japan TEL:81-72-641-9826 Email: Database... classification Toxicogenomics Database Organism Taxonomy Name: Rattus norvegi... Article title: Author name(s): Journal: External Links: Original website information Database

  11. Correlation of resistance and thermogravimetric measurements of the Er/sub 1/Ba/sub 2/Cu/sub 3/O/sub 9-δ/ superconductor to sample preparation techniques

    International Nuclear Information System (INIS)

    Lee, S.I.; Golben, J.P.; Song, Y.; Chen, X.D.; McMichael, R.D.; Gaines, J.R.

    1987-01-01

    The resistance dependence and thermogravimetric analysis (TGA) of Er/sub 1/Ba/sub 2/Cu/sub 3/O/sub 9-δ/ has been measured in the temperature range 27 C to 920 CV. The heat treatments and oxygen flow rates simulated actual sintering and annealing processes used in sample preparation. Evidence of a phase transition in Er/sub 1/Ba/sub 2/Cu/sub 3/O/sub 9-δ/ near 680 C is discussed, as well as the implications of the maximum oxygen uptake near 400 C. The impact of sample preparation procedures on sample features is also discussed

  12. Long-chain fatty acid triglyceride (TG) metabolism disorder impairs male fertility: a study using adipose triglyceride lipase deficient mice.

    Science.gov (United States)

    Masaki, Hidetake; Kim, Namhyo; Nakamura, Hitomi; Kumasawa, Keiichi; Kamata, Eriko; Hirano, Ken-Ichi; Kimura, Tadashi

    2017-07-01

    Does the deletion of adipose triglyceride lipase (Atgl) gene impair male fertility? The deletion of Atgl gene impaired male fertility but the effect was partially reversed by a low long-chain triglyceride (TG) diet. ATGL specifically hydrolyses long-chain fatty acid TG to diacylglycerol and a high level of expression of ATGL in testes has been reported. However, the role of ATGL in male fertility is unknown. To investigate the effect of deletion of Atgl gene on male fertility, cauda epididymides and testes were collected from wild-type, heterozygous and homozygous Atgl-deficient mice at 10 weeks of age and epididymal sperm analysis and histological analysis of the testes were performed. To investigate whether a medium-chain triglycerides (MCTs) replacement diet mitigated the impaired male fertility by deletion of Atgl gene, homozygous Atgl-deficient mice were fed a MCT replacement diet, or a standard diet including long-chain triglycerides (LCTs) in a control group, for 6 weeks from 5 weeks of age (n = 22). The systematic and local effects of the MCT replacement diet on spermatogenesis and sperm maturation in the epididymis were analyzed at 10 weeks of age. Hematoxylin and eosin staining in paraffin-embedded sections of testes and Oil Red O staining in frozen sections of testes were performed. The epididymal sperm concentrations were analyzed. Statistical analyses were performed using the Student's t-test or Mann-Whitney U test with Shapiro-Wilk Normality test. Although heterozygous mice were fertile and showed a similar number of epididymal total and motile sperm concentrations to wild-type mice, the deletion of Atgl gene in homozygous mice led to accumulation of TG deposits in testes and impaired spermatogenesis. The deletion of Atgl gene also impaired the sperm maturation process required for sperm to acquire the ability to move forward in the epididymis. The MCT replacement diet for 6 weeks increased the plasma level of non-esterified fatty acid (NEFA) (1

  13. Sub-Tg enthalpy relaxation in an extremely unstable oxide glass and its implication for structural heterogeneity

    DEFF Research Database (Denmark)

    Zhang, Yanfei; Hu, L.N.; Liu, S.J.

    2013-01-01

    We study the sub-Tg relaxation in an extremely unstable glass former, i.e., 65SiO2-35Al2O3, and its relation to structural heterogeneity (e.g., structurally ordered domains in glass matrix). This is done by hyperquenching (~106 K/s) the liquid, then annealing the hyperquenched glass below Tg...... and subsequently scanning the annealed hyperquenched glass in a differential scanning calorimeter. The results show that structural ordering can take place even below Tg. An endothermic pre-peak is observed when the hyperquenched sample is annealed at 0.75Tg for sufficiently long time, which is, however, much...... weaker compared to that of stable glass formers subjected to same annealing conditions. We also investigate the effect of the sub-Tg annealing on crystallization above Tg. The results imply that some structurally ordered domains exist already in the liquid state. The ordered domains lower the activation...

  14. MO-E-9A-01: Risk Based Quality Management: TG100 In Action

    Energy Technology Data Exchange (ETDEWEB)

    Huq, M [University of Pittsburgh Medical Center, Pittsburgh, PA (United States); Palta, J [Virginia Commonwealth University, Richmond, VA (United States); Dunscombe, P [Tom Baker Cancer Centre, Calgary, AB (Canada); Thomadsen, B [University of Wisconsin, Madison, WI (United States)

    2014-06-15

    One of the goals of quality management in radiation therapy is to gain high confidence that patients will receive the prescribed treatment correctly. To accomplish these goals professional societies such as the American Association of Physicists in Medicine (AAPM) has published many quality assurance (QA), quality control (QC), and quality management (QM) guidance documents. In general, the recommendations provided in these documents have emphasized on performing device-specific QA at the expense of process flow and protection of the patient against catastrophic errors. Analyses of radiation therapy incidents find that they are most often caused by flaws in the overall therapy process, from initial consult through final treatment, than by isolated hardware or computer failures detectable by traditional physics QA. This challenge is shared by many intrinsically hazardous industries. Risk assessment tools and analysis techniques have been developed to define, identify, and eliminate known and/or potential failures, problems, or errors, from a system, process and/or service before they reach the customer. These include, but are not limited to, process mapping, failure modes and effects analysis (FMEA), fault tree analysis (FTA), and establishment of a quality management program that best avoids the faults and risks that have been identified in the overall process. These tools can be easily adapted to radiation therapy practices because of their simplicity and effectiveness to provide efficient ways to enhance the safety and quality of treatment processes. Task group 100 (TG100) of AAPM has developed a risk-based quality management program that uses these tools. This session will be devoted to a discussion of these tools and how these tools can be used in a given radiotherapy clinic to develop a risk based QM program. Learning Objectives: Learn how to design a process map for a radiotherapy process. Learn how to perform a FMEA analysis for a given process. Learn what

  15. MO-E-9A-01: Risk Based Quality Management: TG100 In Action

    International Nuclear Information System (INIS)

    Huq, M; Palta, J; Dunscombe, P; Thomadsen, B

    2014-01-01

    One of the goals of quality management in radiation therapy is to gain high confidence that patients will receive the prescribed treatment correctly. To accomplish these goals professional societies such as the American Association of Physicists in Medicine (AAPM) has published many quality assurance (QA), quality control (QC), and quality management (QM) guidance documents. In general, the recommendations provided in these documents have emphasized on performing device-specific QA at the expense of process flow and protection of the patient against catastrophic errors. Analyses of radiation therapy incidents find that they are most often caused by flaws in the overall therapy process, from initial consult through final treatment, than by isolated hardware or computer failures detectable by traditional physics QA. This challenge is shared by many intrinsically hazardous industries. Risk assessment tools and analysis techniques have been developed to define, identify, and eliminate known and/or potential failures, problems, or errors, from a system, process and/or service before they reach the customer. These include, but are not limited to, process mapping, failure modes and effects analysis (FMEA), fault tree analysis (FTA), and establishment of a quality management program that best avoids the faults and risks that have been identified in the overall process. These tools can be easily adapted to radiation therapy practices because of their simplicity and effectiveness to provide efficient ways to enhance the safety and quality of treatment processes. Task group 100 (TG100) of AAPM has developed a risk-based quality management program that uses these tools. This session will be devoted to a discussion of these tools and how these tools can be used in a given radiotherapy clinic to develop a risk based QM program. Learning Objectives: Learn how to design a process map for a radiotherapy process. Learn how to perform a FMEA analysis for a given process. Learn what

  16. Fragility of chalcogenide glass in relation to characteristic temperature T0/Tg

    Science.gov (United States)

    Shaker, A. M.; Shanker Rao, T.; Lilly Shanker Rao, T.; Venkataraman, K.

    2018-03-01

    The present study reports the mutual relationship between the fragility index m and the characteristic temperature T0/Tg. The fragility of the chalcogenide amorphous glass of Ge10Se50Te40 is calculated by utilizing glass transition temperature (Tg) measured by DSC (Differential Scanning Calorimetry) at different heating rates (β) in the range 5 to 20 K/min. Vogel-Fulcher-Tammann (VFT) equation is fitted to the data of Tg. In addition to the VFT method, three other methods are also used to evaluate m. The fragility index m of the Ge10Se50Te40 system showed the trend of decrease with increasing heating rate but remained stable around 22 for the heating rate 10 K/min. The value of m for the glass is near the lower limit (m ≈ 16) this indicates the alloy is a strong glass forming material in accordance of Angell’s interpretation of fragility. The calculated values of characteristic temperature T0/Tg is very close to 1 which also indicates that clearly the system is most fragile.

  17. TG13 current terminology, etiology, and epidemiology of acute cholangitis and cholecystitis

    NARCIS (Netherlands)

    Kimura, Yasutoshi; Takada, Tadahiro; Strasberg, Steven M.; Pitt, Henry A.; Gouma, Dirk J.; Garden, O. James; Büchler, Markus W.; Windsor, John A.; Mayumi, Toshihiko; Yoshida, Masahiro; Miura, Fumihiko; Higuchi, Ryota; Gabata, Toshifumi; Hata, Jiro; Gomi, Harumi; Dervenis, Christos; Lau, Wan-Yee; Belli, Giulio; Kim, Myung-Hwan; Hilvano, Serafin C.; Yamashita, Yuichi

    2013-01-01

    While referring to the evidence adopted in the Tokyo Guidelines 2007 (TG07) as well as subsequently obtained evidence, further discussion took place on terminology, etiology, and epidemiological data. In particular, new findings have accumulated on the occurrence of symptoms in patients with

  18. Comparison between TG-51 and TRS-398: electron contamination effect on photon beam-quality specification

    International Nuclear Information System (INIS)

    Medina, Antonio Lopez; Teijeiro, Antonio; Salvador, Francisco; Medal, Daniela; Vazquez, Julio; Salgado, Manuel; Carrion, MarIa C

    2004-01-01

    Two dosimetry protocols based on absorbed dose to water have recently been implemented: TG-51 and TRS-398. These protocols use different beam-quality indices. The effect of electron contamination in measurements of %dd(10) x has been proposed as a disadvantage of the TG-51. For actual measurements of %dd(10) x in five clinical beams ) a purging magnet was employed to remove the electron contamination. Also, %dd(10) x was measured in the different ways described in TG-51 for high-energy beams: with a lead foil at 50 cm from the phantom surface, at 30 cm, and for open beam. Moreover, TPR 20,10 was determined. Also, periodic quality-control measurements were used for comparing both quality indices and variation over time, but D 20,10 was used instead of TPR 20,10 and measurements in open beam for the %dd(10) x determination. Considering both protocols, S w,air and k Q were calculated in order to compare the results with the experimental data. Significant differences (0.3% for k Q ) were only found for the two high-energy beams, but when the electron contamination is underestimated by TG-51, the difference in k Q is lower. Differences in the other cases and variations over time were less than 0.1%

  19. Ocular Changes in TgF344-AD Rat Model of Alzheimer's Disease

    OpenAIRE

    Tsai, Yuchun; Lu, Bin; Ljubimov, Alexander V.; Girman, Sergey; Ross-Cisneros, Fred N.; Sadun, Alfredo A.; Svendsen, Clive N.; Cohen, Robert M.; Wang, Shaomei

    2014-01-01

    In this study, we observed pathological changes in the choroid and in RPE cells in the TgF344-AD rat model; choroidal thinning was further observed in human AD retina. Along with Aβ deposition, the inflammatory response was manifested by microglial recruitment and complement activation.

  20. Body weight - Open TG-GATEs | LSDB Archive [Life Science Database Archive metadata

    Lifescience Database Archive (English)

    Full Text Available switchLanguage; BLAST Search Image Search Home About Archive Update History Data ...le URL: ftp://ftp.biosciencedbc.jp/archive/open-tggates/LATEST/open_tggates_body_...atabase Description Download License Update History of This Database Site Policy | Contact Us Body weight - Open TG-GATEs | LSDB Archive ...

  1. Detecting spatial memory deficits beyond blindness in tg2576 Alzheimer mice.

    Science.gov (United States)

    Yassine, Nour; Lazaris, Anelise; Dorner-Ciossek, Cornelia; Després, Olivier; Meyer, Laurence; Maitre, Michel; Mensah-Nyagan, Ayikoe Guy; Cassel, Jean-Christophe; Mathis, Chantal

    2013-03-01

    The retinal degeneration Pde6b(rd1) (rd) mutation can be a major pitfall in behavioral studies using tg2576 mice bred on a B6:SJL genetic background, 1 of the most widely used models of Alzheimer's disease. After a pilot study in wild type mice, performance of 8- and 16-month-old tg2576 mice were assessed in several behavioral tasks with the challenge of selecting 1 or more task(s) showing robust memory deficits on this genetic background. Water maze acquisition was impossible in rd homozygotes, whereas Y-maze alternation, object recognition, and olfactory discrimination were unaffected by both the transgene and the rd mutation. Spatial memory retention of 8- and 16-month-old tg2576 mice, however, was dramatically affected independently of the rd mutation when mice had to recognize a spatial configuration of objects or to perform the Barnes maze. Thus, the latter tasks appear extremely useful to evaluate spatial memory deficits and to test cognitive therapies in tg2576 mice and other mouse models bred on a background susceptible to visual impairment. Copyright © 2013 Elsevier Inc. All rights reserved.

  2. Combustion behaviour of Sydney and Bowen Basin coals determined by thermogravimetry

    Energy Technology Data Exchange (ETDEWEB)

    Benfell, K.E.; Beamish, B.B.; Rodgers, K.A.; Crosdale, P.J. [University of Auckland, Auckland (New Zealand). Department of Geology

    1996-08-01

    Assesses the suitability of thermogravimetric (TG) and derivative thermogravimetric (DTG) analysis techniques to characterise the combustion behaviour of Sydney and Bowen basin coals. Results indicate that the thermogravimetric technique is suitable for characterising the effects of rank, maceral, sub-maceral and seam variations on the combustion behaviour of these coals. 6 refs., 6 figs., 2 tabs.

  3. SU-F-T-22: Clinical Implications When Using TG-186 (ACE) Heterogeneity Software

    Energy Technology Data Exchange (ETDEWEB)

    Likhacheva, A; Grade, E; Sadeghi, A; Sokolowski, T [Arizona Cancer Specialists, Mesa, AZ (United States)

    2016-06-15

    Purpose: The purpose of this study is to compare dosimetric calculations using traditional TG-43 formalism and Oncentra Brachy Advanced Collapsed cone Engine (ACE) TG-186 calculation algorithm in clinical setting. Methods: We analyzed dosimetry of four patients treated with accelerated partial breast irradiation using a multi-channel intracavitary device (SAVI). All patients were treated to 34 Gy in 10 fractions using a high-dose-rate (192) Ir source. The plans were designed and treated using the TG-43 model. ACE was used to assess the effect heterogeneity correction on various dosimetric parameters. Mass density was estimated using Hounsfield units. Results: Compared to TG-43 formalism, ACE estimated lower doses to targets and organs at risk. The mean difference was 19.8% (range 15.3–24.1%) for PTV-eval V200, 12.0% (range 9.7–17.7%) for PTV-eval V150, 4.3% (range 3.3–6.5%) for PTV-eval D95, 3.3% (range 1.4–5.4%) for PTV-eval D90, 5.4% (range 2.9–9.9%) for maximum rib dose, and 5.7% (2.4–7.4%) for maximum skin dose. There was no correlation between the magnitude of the difference and the PTV-eval volume, air volume, or tissue-applicator conformance. Conclusion: Based on our preliminary study, the TG-43 algorithm appears to overestimate the dose to targets and organs at risk when compared to the ACE TG-186 software. We hypothesize that air adjacent to the SAVI struts contributes to lack of scatter thereby contributing a significant difference in dose calculation when using ACE. We believe that ACE calculation provides a more realistic isodose distribution than TG-43. We plan to further investigate the impact of heterogeneity correction on brachytherapy planning for a wide variety of clinical scenarios, include skin, cervix/uterus, prostate, and lung.

  4. Molybdenum(V, germanium(IV, aluminum(III and nickel(II adducts with ethyleneurea, ethylenethiourea and propyleneurea: some empirical correlations involving TG and IR data

    Directory of Open Access Journals (Sweden)

    ROBSON F. DE FARIAS

    2006-03-01

    Full Text Available The adducts MoCl5·2eu, MoCl5·2pu, GeCl4·2etu, AlCl3·2pu, AlCl3·3pu, NiCl2·2etu and NiCl2·4etu (eu = ethyleneurea, etu = ethylenethiourea and pu =propyleneurea were synthesized and characterized by elemental analysis (C, H, N, infrared spectroscopy (IR and thermogravimetry (TG. IR Results show that eu and pu coordinate through oxygen, whereas etu coordinates through nitrogen. For all investigated adducts, a single mass loss step associated with the release of ligand molecules is observed. Empirical correlations involving TG and IR data are established.

  5. INFLUENCE OF BIOPRETREATMENT ON THE CHARACTER OF CORN STOVER LIGNIN AS SHOWN BY THERMOGRAVIMETRIC AND CHEMICAL STRUCTURAL ANALYSES

    OpenAIRE

    Xuewei Yang; Yelin Zeng; Xiaoyu Zhang

    2010-01-01

    The effect of corn stover lignin structure alteration caused by white-rot fungi pretreatment on the pyrolysis kinetics was studied by FTIR and TG/DTA. Results showed that biopretreatment had a remarkable effect on lignin pyrolysis. Biopretreatment can decrease the activation energy and increase the pre-exponential factor in the initial stage of pyrolysis, which makes it possible to start the lignin pyrolysis at a relatively gentle condition and improve the availability of biomass pyrolysis as...

  6. XRD, TEM, and thermal analysis of Arizona Ca-montmorillonites modified with didodecyldimethylammonium bromide.

    Science.gov (United States)

    Sun, Zhiming; Park, Yuri; Zheng, Shuilin; Ayoko, Godwin A; Frost, Ray L

    2013-10-15

    An Arizona SAz-2 calcium montmorillonite was modified by a typical dialkyl cationic surfactant (didodecyldimethylammonium bromide, abbreviated to DDDMA) through direct ion exchange. The obtained organoclays were characterized by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HR-TEM), high-resolution thermogravimetric analysis (HR-TG), and infrared emission spectroscopy (IES). The intercalation of surfactants greatly increased the basal spacing of the interlayers and the conformation arrangement of the loaded surfactant were assessed based on the XRD and TEM measurements. This work shows that the dialkyl surfactant can be directly intercalated into the montmorillonite without first undergoing Na(+) exchange. Moreover, the thermal stability of organoclays and the different arrangements of the surfactant molecules intercalated in the SAz-2 Ca-montmorillonite were determined by a combination of TG and IES techniques. The detailed conformational ordering of different intercalated surfactants under different conditions was also studied. The surfactant molecule DDDMA has proved to be thermally stable even at 400°C which indicates that the prepared organoclay is stable to significantly high temperatures. This study offers new insights into the structure and thermal stabilities of SAz-2 Ca-montmorillonite modified with DDDMA. The experimental results also confirm the potential applications of organic SAz-2 Ca-montmorillonites as adsorbents and polymer-clay nanocomposites. Copyright © 2013 Elsevier Inc. All rights reserved.

  7. Age-dependent modifications of AMPA receptor subunit expression levels and related cognitive effects in 3xTg-AD mice

    Directory of Open Access Journals (Sweden)

    Pamela eCantanelli

    2014-08-01

    Full Text Available GluA1, GluA2, GluA3, and GluA4 are the constitutive subunits of AMPA receptors (AMPARs, the major mediators of fast excitatory transmission in the mammalian central nervous system. Most AMPARs are Ca2+-impermeable because of the presence of the GluA2 subunit. GluA2 mRNA undergoes an editing process that results in a Q to R substitution, a key factor in the regulation of AMPAR Ca2+-permeability. AMPARs lacking GluA2 or containing the unedited subunit are permeable to Ca2+ and Zn2+. The phenomenon physiologically modulates synaptic plasticity while, in pathologic conditions, leads to increased vulnerability to excitotoxic neuronal death. Given the importance of these subunits, we have therefore evaluated possible associations between changes in expression levels of AMPAR subunits and development of cognitive deficits in 3xTg-AD mice, a widely investigated transgenic mouse model of Alzheimer’s disease. With qRT-PCR, we assayed hippocampal mRNA expression levels of GluA1-4 subunits occurring in young [3 months of age (m.o.a.] and old (12 m.o.a Tg-AD mice and made comparisons with levels found in age-matched wild type (WT mice. Efficiency of GluA2 RNA editing was also analyzed. All animals were cognitively tested for short- and long-term spatial memory with the Morris Water Maze (MWM navigation task. 3xTg-AD mice showed age-dependent decreases of mRNA levels for all the AMPAR subunits, with the exception of GluA2. Editing remained fully efficient with aging in 3xTg-AD and WT mice. A one-to-one correlation analysis between MWM performances and GluA1-4 mRNA expression profiles showed negative correlations between GluA2 levels and MWM performances in young 3xTg-AD mice. On the contrary, positive correlations between GluA2 mRNA and MWM performances were found in young WT mice. Our data suggest that increases of AMPARs that contain GluA1, GluA3, and GluA4 subunits may help in maintaining cognition in pre-symptomatic 3xTg-AD mice.

  8. SU-F-T-485: Independent Remote Audits for TG51 NonCompliant Photon Beams Performed by the IROC Houston QA Center

    Energy Technology Data Exchange (ETDEWEB)

    Alvarez, P; Molineu, A; Lowenstein, J; Taylor, P; Kry, S; Followill, D [UT MD Anderson Cancer Center, Houston, TX (United States)

    2016-06-15

    Purpose: IROC-H conducts external audits for output check verification of photon and electron beams. Many of these beams can meet the geometric requirements of the TG 51 calibration protocol. For those photon beams that are non TG 51 compliant like Elekta GammaKnife, Accuray CyberKnife and TomoTherapy, IROC-H has specific audit tools to monitor the reference calibration. Methods: IROC-H used its TLD and OSLD remote monitoring systems to verify the output of machines with TG 51 non compliant beams. Acrylic OSLD miniphantoms are used for the CyberKnife. Special TLD phantoms are used for TomoTherapy and GammaKnife machines to accommodate the specific geometry of each machine. These remote audit tools are sent to institutions to be irradiated and returned to IROC-H for analysis. Results: The average IROC-H/institution ratios for 480 GammaKnife, 660 CyberKnife and 907 rotational TomoTherapy beams are 1.000±0.021, 1.008±0.019, 0.974±0.023, respectively. In the particular case of TomoTherapy, the overall ratio is 0.977±0.022 for HD units. The standard deviations of all results are consistent with values determined for TG 51 compliant photon beams. These ratios have shown some changes compared to values presented in 2008. The GammaKnife results were corrected by an experimentally determined scatter factor of 1.025 in 2013. The TomoTherapy helical beam results are now from a rotational beam whereas in 2008 the results were from a static beam. The decision to change modality was based on recommendations from the users. Conclusion: External audits of beam outputs is a valuable tool to confirm the calibrations of photon beams regardless of whether the machine is TG 51 or TG 51 non compliant. The difference found for TomoTherapy units is under investigation. This investigation was supported by IROC grant CA180803 awarded by the NCI.

  9. SU-F-T-485: Independent Remote Audits for TG51 NonCompliant Photon Beams Performed by the IROC Houston QA Center

    International Nuclear Information System (INIS)

    Alvarez, P; Molineu, A; Lowenstein, J; Taylor, P; Kry, S; Followill, D

    2016-01-01

    Purpose: IROC-H conducts external audits for output check verification of photon and electron beams. Many of these beams can meet the geometric requirements of the TG 51 calibration protocol. For those photon beams that are non TG 51 compliant like Elekta GammaKnife, Accuray CyberKnife and TomoTherapy, IROC-H has specific audit tools to monitor the reference calibration. Methods: IROC-H used its TLD and OSLD remote monitoring systems to verify the output of machines with TG 51 non compliant beams. Acrylic OSLD miniphantoms are used for the CyberKnife. Special TLD phantoms are used for TomoTherapy and GammaKnife machines to accommodate the specific geometry of each machine. These remote audit tools are sent to institutions to be irradiated and returned to IROC-H for analysis. Results: The average IROC-H/institution ratios for 480 GammaKnife, 660 CyberKnife and 907 rotational TomoTherapy beams are 1.000±0.021, 1.008±0.019, 0.974±0.023, respectively. In the particular case of TomoTherapy, the overall ratio is 0.977±0.022 for HD units. The standard deviations of all results are consistent with values determined for TG 51 compliant photon beams. These ratios have shown some changes compared to values presented in 2008. The GammaKnife results were corrected by an experimentally determined scatter factor of 1.025 in 2013. The TomoTherapy helical beam results are now from a rotational beam whereas in 2008 the results were from a static beam. The decision to change modality was based on recommendations from the users. Conclusion: External audits of beam outputs is a valuable tool to confirm the calibrations of photon beams regardless of whether the machine is TG 51 or TG 51 non compliant. The difference found for TomoTherapy units is under investigation. This investigation was supported by IROC grant CA180803 awarded by the NCI

  10. Acoustic Doppler current profiling from the JGOFS Arabian Sea cruises aboard the RV T.G. Thompson

    Energy Technology Data Exchange (ETDEWEB)

    Kim, H.S.; Flagg, C.N.; Shi, Y. [Brookhaven National Lab., Upton, NY (United States). Oceanographic and Atmospheric Sciences Div.

    1996-12-01

    Acoustic Doppler current profiler (ADCP) data is part of the core data for the US JGOFS Arabian Sea project, along with hydrographic and nutrient data. Seventeen cruises are scheduled to take place between September 1994 and January 1996 on the R/V T.G. Thompson. Seven of the cruises follow a standard cruise track, taking hydrographic, chemical and biological measurements. The rest of the cruises, which take place generally within the standard cruise region defined by a set track, are for the deployment and recovery of moored equipment and towing of a SeaSoar. Detailed description of ADCP hardware, the AutoADCP data acquisition system, and the collection of navigation and compass data on the Thompson is documented in Section 2. Followed by data collection for each cruise together with a cruise track, Section 3 presents the processing and analysis of velocity and acoustic backscatter intensity data. Section 5 shows results of profile quality diagnosis.

  11. Thermogravimetric Characterization of the Microstructui Composition of Polyamide Injection Molded Denture Base Material vs Conventional Compression Molded Heat-cured Denture Base Material.

    Science.gov (United States)

    Al-Dharrab, Ayman; Shinawi, Lana

    2016-02-01

    Thermoplastic resin polymers are widely used in medicine due to their biostability and hypoallergenic properties, making them a possible alternative to poly-methylmethacrylate (PMMA). The current research examined the microstructure of a rapid injection molding system thermoplastic resin for construction of flexible denture compared with that of heat-cured PMMA. A total of 40 disk-shaped specimens (25 mm in diameter and 3 mm in thickness) were prepared and divided into two groups of 20 disks each (group I samples were of thermoplastic acrylic resin while group II was heat-cured PMMA resin). In group I, thermogravimetric analyzer showed that increasing the temperature up to 169°C resulted in about 1.3% of the material loss, and after that the material remains thermally stable up to 200°C. Group 11 showed 2.24% weight loss at 171°C, and further weight loss (12.025%) was observed on heating to 230°C. Fourier transform infrared (FTIR) spectrophotometer analysis in the range of 400-4000 cm(-1) detected the presence of an amine group (N-H) in group I samples and the presence of methylene group attached to inorganic Si as reinforcement filler (Si-CH3). Thermoplastic resin displayed excellent thermal stability and the absence of residual monomer within the polymerized material, suggesting its suitability for the fabrication dentures.

  12. Thermogravimetric and Magnetic Studies of the Oxidation and Reduction Reaction of SmCoO3 to Nanostructured Sm2O3 and Co

    Science.gov (United States)

    Kelly, Brian; Cichocki, Ronald; Poirier, Gerald; Unruh, Karl

    The SmCoO3 to nanostructured Sm2O3 and Co oxidation and reduction reaction has been studied by thermogravimetric analysis (TGA) measurements in forming gas (FG) and inert N2 atmospheres, x-ray diffraction (XRD) and vibrating sample magnetometry (VSM). The TGA measurements showed two clearly resolvable reduction processes when heating in FG, from the initial SmCoO3 phase through an intermediate nanostructured mixture of Sm2O3 and CoO when heated to 330°C for several minutes, and then the conversion of CoO to metallic Co when heated above 500°C. These phases were confirmed by XRD and VSM. Similar measurements in N2 yielded little mass change below 900°C and coupled reduction processes at higher temperatures. Isoconversional measurements of the CoO to Co reduction reaction in FG yielded activation energies above 2eV/atom in the nanostructured system. This value is several times larger than those reported in the literature or obtained by similar measurements of bulk mixtures of Sm2O3 and CoO, suggesting the nanostructuring was the source of the large increase in activation energy.

  13. SU-E-T-159: Evaluation of a Patient Specific QA Tool Based On TG119

    International Nuclear Information System (INIS)

    Ashmeg, S; Zhang, Y; O'Daniel, J; Yin, F; Ren, L

    2014-01-01

    Purpose: To evaluate the accuracy of a 3D patient specific QA tool by analysis of the results produced from associated software in homogenous phantom and heterogonous patient CT. Methods: IMRT and VMAT plans of five test suites introduced by TG119 were created in ECLIPSE on a solid water phantom. The ten plans -of increasing complexity- were delivered to Delta4 to give a 3D measurement. The Delta4's “Anatomy” software uses the measured dose to back-calculate the energy fluence of the delivered beams, which is used for dose calculation in a patient CT using a pencilbeam algorithm. The effect of the modulated beams' complexity on the accuracy of the “Anatomy” calculation was evaluated. Both measured and Anatomy doses were compared to ECLIPSE calculation using 3% - 3mm gamma criteria.We also tested the effect of heterogeneity by analyzing the results of “Anatomy” calculation on a Brain VMAT and a 3D conformal lung cases. Results: In homogenous phantom, the gamma passing rates were found to be as low as 74.75% for a complex plan with high modulation. The mean passing rates were 91.47% ± 6.35% for “Anatomy” calculation and 99.46% ± 0.62% for Delta4 measurements.As for the heterogeneous cases, the rates were 96.54%±3.67% and 83.87%±9.42% for Brain VMAT and 3D lung respectively. This increased error in the lung case could be due to the use of the pencil beam algorithm as opposed to the AAA used by ECLIPSE.Also, gamma analysis showed high discrepancy along the beam edge in the “Anatomy” calculated results. This suggests a poor beam modeling in the penumbra region. Conclusion: The results show various sources of errors in “Anatomy” calculations. These include beam modeling in the penumbra region, complexity of a modulated beam (shown in homogenous phantom and brain cases) and dose calculation algorithms (3D conformal lung case)

  14. Mechanisms contributing to the thermal analysis of waste incineration bottom ash and quantification of different carbon species.

    Science.gov (United States)

    Rocca, Stefania; van Zomeren, André; Costa, Giulia; Dijkstra, Joris J; Comans, Rob N J; Lombardi, Francesco

    2013-02-01

    The focus of this study was to identify the main compounds affecting the weight changes of bottom ash (BA) in conventional loss on ignition (LOI) tests and to obtain a better understanding of the individual processes in heterogeneous (waste) materials such as BA. Evaluations were performed on BA samples from a refuse derived fuel incineration (RDF-I) plant and a hospital waste incineration (HW-I) plant using thermogravimetric analysis and subsequent mass spectrometry (TG-MS) analysis of the gaseous thermal decomposition products. Results of TG-MS analysis on RDF-I BA indicated that the LOI measured at 550°C was due to moisture evaporation and dehydration of Ca(OH)(2) and hydrocalumite. Results for the HW-I BA showed that LOI at 550°C was predominantly related to the elemental carbon (EC) content of the sample. Decomposition of CaCO(3) around 700°C was identified in both materials. In addition, we have identified reaction mechanisms that underestimate the EC and overestimate the CaCO(3) contents of the HW-I BA during TG-MS analyses. These types of artefacts are expected to occur also when conventional LOI methods are adopted, in particular for materials that contain CaO/Ca(OH)(2) in combination with EC and/or organic carbon, such as e.g. municipal solid waste incineration (MSWI) bottom and fly ashes. We suggest that the same mechanisms that we have found (i.e. in situ carbonation) can also occur during combustion of the waste in the incinerator (between 450 and 650°C) demonstrating that the presence of carbonate in bottom ash is not necessarily indicative for weathering. These results may also give direction to further optimization of waste incineration technologies with regard to stimulating in situ carbonation during incineration and subsequent potential improvement of the leaching behavior of bottom ash. Copyright © 2012 Elsevier Ltd. All rights reserved.

  15. Evaluation of TG-43 recommended 2D-anisotropy function for elongated brachytherapy sources

    International Nuclear Information System (INIS)

    Awan, Shahid B.; Meigooni, Ali S.; Mokhberiosgouei, Ramin; Hussain, Manzoor

    2006-01-01

    The original and updated protocols recommended by Task Group 43 from the American Association of Physicists in Medicine (i.e., TG-43 and TG-43U1, respectively), have been introduced to unify brachytherapy source dosimetry around the world. Both of these protocols are based on experiences with sources less than 1.0 cm in length. TG-43U1 recommends that for 103 Pd sources, 2D anisotropy function F(r,θ), should be tabulated at a minimum for radial distances of 0.5, 1.0, 2.0, 3.0, and 5.0 cm. Anisotropy functions defined in these protocols are only valid when the point of calculation does not fall on the active length of the source. However, for elongated brachytherapy sources (active length >1 cm), some of the calculation points with r 103 Pd source at radial distances of 2.5, 3.0, and 4.0 cm were 2.95, 1.74, and 1.19, respectively, with differences up to about a factor of 3. Therefore, the validity of the linear interpolation technique for an elongated brachytherapy source with such a large variation in F(r,θ) needs to be investigated. In this project, application of the TG-43U1 formalism for dose calculation around an elongated RadioCoil trade mark sign 103 Pd brachytherapy source has been investigated. In addition, the linear interpolation techniques as described in TG-43U1 for seed type sources have been evaluated for a 5.0 cm long RadioCoil trade mark sign 103 Pd brachytherapy source. Application of a polynomial fit to F(r,θ) has also been investigated as an alternate approach to the linear interpolation technique. The results of these investigations indicate that the TG-43U1 formalism can be extended for elongated brachytherapy sources, if the two-dimensional (2D) anisotropy function is tabulated at a minimum for radial distances of 0.2, 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0 cm, L/2, and L/2±0.2 cm. Moreover, with the addition of recommended radial distances for 2D anisotropy functions, the linear interpolation technique more closely replicates

  16. Impaired hippocampal acetylcholine release parallels spatial memory deficits in Tg2576 mice subjected to basal forebrain cholinergic degeneration

    DEFF Research Database (Denmark)

    Laursen, Bettina; Mørk, Arne; Plath, Niels

    2013-01-01

    (BFCD) in 3 months old male Tg2576 mice to co-express cholinergic degeneration with Aβ overexpression as these characteristics constitutes key hallmarks of AD. At 9 months, SAP lesioned Tg2576 mice were cognitively impaired in two spatial paradigms addressing working memory and mid to long-term memory...

  17. Observation of changes of serum leptin and lipid (TG and TC) levels in patients with graves' disease

    International Nuclear Information System (INIS)

    Wang Zhaobao; Cheng Guanghua

    2008-01-01

    Objective: To investigate the clinical significance of changes of serum leptin (with RIA) and lipid (TG and TC) (with biochemistry) levels in patients with Graves' disease. Methods: Serum Leptin, TG and TC levels were determined in 29 patients with Graves' disease both before and after treatment as well as in 30 controls. Results: Before treatment, serum Leptin, TG and TC levels in the patients were significantly lower than those in the controls. After treatment, serum Leptin, TG and TC levels increased and were significantly higher than those before treatment and were not much different from those in controls. Conclusion: The changes of serum Leptin, TG and TC levels may be of value for outcome prediction in patients with Graves' disease. (authors)

  18. Sub-Tg enthalpy relaxation in an unstable oxide glass former: insights into the structural heterogeneity

    DEFF Research Database (Denmark)

    Yue, Yuanzheng; Zhang, Yanfei

    Structural heterogeneity plays a crucial role in determining functionality of glasses. In this work we have found that the sub-Tg enthalpy relaxation pattern in a hyperquenched glass is highly sensitive to structural heterogeneity. As a consequence, the former can be used as an effective approach...... to detect and quantify the structural heterogeneity in glass-forming liquids. However, the chemical nature of structural heterogeneity should be revealed by other means such as high resolution microscopic and spectroscopic methods. To study the impact of the structural heterogeneity on the sub-Tg relaxation...... chemical features and degrees of structural heterogeneity in glass-forming liquids. This finding contributes to the microscopic origin of both the primary and secondary relaxation in terms of structural heterogeneity. Finally the results provide insights into the relation between structural heterogeneity...

  19. Characteristic Study of Some Different Kinds of Coal Particles Combustion with Online TG-MS-FTIR

    Science.gov (United States)

    Pan, Guanfu

    2018-01-01

    Four kinds of pulverized coal samples from China and Indonesia were studied by thermogravimetry coupled with mass spectrometry and fourier transform infrared spectroscopy (TG-MS-FTIR). The thermal behaviors and gaseous emissions of these coals were analyzed in this work. The results indicate that the relative lower values of H/C ratios, which normally represent the degree of aromatization and ring condensation in coal samples, could lead to the relative more intense thermal reaction. The time-evolved profiles of some typical gas products (i.e., CO, SO2, CH4, NO, NO2, NH3 and etc.) were provided by TG-MS-FTIR, and their variations are different. For all the samples, the releases of SO2 and COS can be found at lower temperature than those of NO and CO. As the temperature increases, the possible conversion of NO2 and NH3 to NO is deduced in this work.

  20. Abnormal three-steplike sub-Tg enthalpy relaxation pattern in hyperquenched metallic glasses

    DEFF Research Database (Denmark)

    Hu, Lina; Yue, Yuanzheng

    Our recent work observed a quite different relaxation pattern, i.e., the abnormal three-steplike sub-Tg relaxation in CuZrAl GRs[1]. However, the generality and the origin of this remarkable thermodynamic anomaly remain enigmatic. By hyperquenching strategy, the present work investigated the depe......Our recent work observed a quite different relaxation pattern, i.e., the abnormal three-steplike sub-Tg relaxation in CuZrAl GRs[1]. However, the generality and the origin of this remarkable thermodynamic anomaly remain enigmatic. By hyperquenching strategy, the present work investigated...... in La55Al25Ni20 GRs. However, the correlation between Tf and the activation energy for initiating the energy releasing during thermal scanning is three-steplike for La55Al25Ni20, revealing the similar phenomenon with the abnormal ERP of Cu46Zr46Al8. These unexpected phenomena have been well explained...

  1. Role of humidity and other correction factors in the AAPM TG-21 dosimetry protocol

    International Nuclear Information System (INIS)

    Rogers, D.W.; Ross, C.K.

    1988-01-01

    A detailed derivation is presented of the formulas required to determine Ngas and Dmed in the AAPM TG-21 dosimetry protocol. This protocol specifies how to determine the absorbed dose in an electron or photon beam when using exposure or absorbed dose calibrated ion chambers. It is shown that the expression given in TG-21's recent letter of clarification is incorrect. Accounting for humidity correctly increases, by 0.4%, all absorbed dose determinations using an exposure calibrated ion chamber. Taking into account other correction factors in the equation for exposure could also have varying, but significant effects (possibly over 1%). These are the stem scatter correction, the axial nonuniformity correction and the electrode correction for electrodes made of different materials from the wall. Attention is drawn to differences in the definitions of the exposure and absorbed dose calibration factors, Nx and ND, respectively, as supplied by the NBS and the NRCC

  2. SU-E-T-179: Clinical Impact of IMRT Failure Modes at Or Near TG-142 Tolerance Criteria Levels

    Energy Technology Data Exchange (ETDEWEB)

    Faught, J Tonigan; Balter, P; Johnson, J; Kry, S; Court, L; Stingo, F; Followill, D [UT MD Anderson Cancer Center, Houston, TX (United States)

    2015-06-15

    Purpose: Quantitatively assess the clinical impact of 11 critical IMRT dose delivery failure modes. Methods: Eleven step-and-shoot IMRT failure modes (FMs) were introduced into twelve Pinnacle v9.8 treatment plans. One standard and one highly modulated plan on the IROC IMRT phantom and ten previous H&N patient treatment plans were used. FMs included physics components covered by basic QA near tolerance criteria levels (TG-142) such as beam energy, MLC positioning, and MLC modeling. Resultant DVHs were compared to those of failure-free plans and the severity of plan degradation was assessed considering PTV coverage and OAR and normal tissue tolerances and used for FMEA severity scoring. Six of these FMs were physically simulated and phantom irradiations performed. TLD and radiochromic film results are used for comparison to treatment planning studies. Results: Based on treatment planning studies, the largest clinical impact from the phantom cases was induced by 2 mm systematic MLC shift in one bank with the combination of a D95% target under dose near 16% and OAR overdose near 8%. Cord overdoses of 5%–11% occurred with gantry angle, collimator angle, couch angle, MLC leaf end modeling, and MLC transmission and leakage modeling FMs. PTV coverage and/or OAR sparing was compromised in all FMs introduced in phantom plans with the exception of CT number to electron density tables, MU linearity, and MLC tongue-and-groove modeling. Physical measurements did not entirely agree with treatment planning results. For example, symmetry errors resulted in the largest physically measured discrepancies of up to 3% in the PTVs while a maximum of 0.5% deviation was seen in the treatment planning studies. Patient treatment plan study results are under analysis. Conclusion: Even in the simplistic anatomy of the IROC phantom, some basic physics FMs, just outside of TG-142 tolerance criteria, appear to have the potential for large clinical implications.

  3. c.1643_1644delTG XPC mutation is more frequent in Moroccan patients with xeroderma pigmentosum.

    Science.gov (United States)

    Senhaji, Mohamed Amine; Abidi, Omar; Nadifi, Sellama; Benchikhi, Hakima; Khadir, Khadija; Ben Rekaya, Mariem; Eloualid, Abdelmajid; Messaoud, Olfa; Abdelhak, Sonia; Barakat, Abdelhamid

    2013-01-01

    Xeroderma pigmentosum is a rare autosomal recessive disease characterized by hypersensitivity to UV light which is due to alterations of the nucleotide excision repair pathway. Eight genes (XPA to XPG and XPV) are responsible for the disease. Among them, the XPC gene is known to be the most mutated in Mediterranean patients. The aim of this study was to determine the frequency of the most common XPC mutation and describe the clinical features of Moroccan patients with xeroderma pigmentosum. Twenty four patients belonging to 21 unrelated Moroccan families and 58 healthy subjects were investigated. After clinical examination, the screening for the c.1643_1644delTG (p.Val548AlafsX25) mutation in the XPC gene was performed by PCR and automated sequencing of exon 9 in all patients and controls. The molecular analysis showed that among the 24 patients, 17 were homozygous for the c.1643_1644delTG mutation and all their tested parents were heterozygous, whereas the others (7 patients) did not carry the mutation. The frequency of this mutation was estimated to be 76.19 % (16/21 families). None of the 58 healthy individuals carried this mutation. In addition, clinical investigation showed that the majority of the patients bearing this mutation have the same clinical features. Our results revealed that the p.Val548AlafsX25 mutation is the major cause (76.19 %) of xeroderma pigmentosum in Moroccan families. This would have an important impact on improving management of patients and their relatives.

  4. Thermogravimetric method of estimation of uranyl cation state in melts of alkali metal chlorides and their mixtures

    International Nuclear Information System (INIS)

    Vorobej, M.P.; Desyatnik, V.N.

    1979-01-01

    The thermogravimetric method was used to study the chloridizing of uranium oxides in molten media. The study of the uranium oxide chloridizing served as a basis for evaluating comparatively, using the DTA method, the uranyl-cation state in a melt. Using the alkali metals as example, it was shown that the decomposition of the frozen uranium oxychlorides proceeds with the formation of intermediate chlorouranates. The final product of the thermolysis are uranates Me 2 U 2 O 7 (Me-Li, Na, K, Rb, Cs). The time and the conditions of the change of uranium oxides to the oxyanion [UO 2 Cl 4 ] 2- were determined as a function of the chloridizing agent. The method can be employed for evaluating uranyl-ions in molten media where they are used as electrolytes in the extraction of uranium dioxide

  5. A Monte Carlo derived TG-51 equivalent calibration for helical tomotherapy

    International Nuclear Information System (INIS)

    Thomas, S.D.; Mackenzie, M.; Rogers, D.W.O.; Fallone, B.G.

    2005-01-01

    Helical tomotherapy (HT) requires a method of accurately determining the absorbed dose under reference conditions. In the AAPM's TG-51 external beam dosimetry protocol, the quality conversion factor, k Q , is presented as a function of the photon component of the percentage depth-dose at 10 cm depth, %dd(10) x , measured under the reference conditions of a 10x10 cm 2 field size and a source-to-surface distance (SSD) of 100 cm. The value of %dd(10) x from HT cannot be used for the determination of k Q because the design of the HT does not meet the following TG-51 reference conditions: (i) the field size and the practical SSD required by TG-51 are not obtainable and (ii) the absence of the flattening filter changes the beam quality thus affecting some components of k Q . The stopping power ratio is not affected because of its direct relationship to %dd(10) x . We derive a relationship for the Exradin A1SL ion chamber converting the %dd(10) x measured under HT 'reference conditions' of SSD=85 cm and a 5x10 cm 2 field-size [%dd(10) x[HTRef] ], to the dosimetric equivalent value under for TG-51 reference conditions [%dd(10) x[HTTG-51] ] for HT. This allows the determination of k Q under the HT reference conditions. The conversion results in changes of 0.1% in the value of k Q for our particular unit. The conversion relationship should also apply to other ion chambers with possible errors on the order of 0.1%

  6. Helhetsorienterad utvärdering av kollektivtrafikåtgärder

    DEFF Research Database (Denmark)

    Hiselius, Lena Winslott; Barfod, Michael Bruhn; Leleur, Steen

    Under hösten 2008 och våren 2009 har forskare vid Avd. Trafik och väg vid Lunds Tekniska Högskola, DTU Transport vid Danmarks Tekniska Universitet samt National-ekonomiska institutionen vid Lunds Universitet genomfört ett forskningsprojekt med syfte att studera tillämpningen av en sammansatt...... (helhetsorienterad) analys av kollektiv-trafikåtgärder....

  7. Cotinine improves visual recognition memory and decreases cortical Tau phosphorylation in the Tg6799 mice.

    Science.gov (United States)

    Grizzell, J Alex; Patel, Sagar; Barreto, George E; Echeverria, Valentina

    2017-08-01

    Alzheimer's disease (AD) is associated with the progressive aggregation of hyperphosphorylated forms of the microtubule associated protein Tau in the central nervous system. Cotinine, the main metabolite of nicotine, reduced working memory deficits, synaptic loss, and amyloid β peptide aggregation into oligomers and plaques as well as inhibited the cerebral Tau kinase, glycogen synthase 3β (GSK3β) in the transgenic (Tg)6799 (5XFAD) mice. In this study, the effect of cotinine on visual recognition memory and cortical Tau phosphorylation at the GSK3β sites Serine (Ser)-396/Ser-404 and phospho-CREB were investigated in the Tg6799 and non-transgenic (NT) littermate mice. Tg mice showed short-term visual recognition memory impairment in the novel object recognition test, and higher levels of Tau phosphorylation when compared to NT mice. Cotinine significantly improved visual recognition memory performance increased CREB phosphorylation and reduced cortical Tau phosphorylation. Potential mechanisms underlying theses beneficial effects are discussed. Copyright © 2017. Published by Elsevier Inc.

  8. Textural properties of low-fat set-type yoghurt depending on mTG addition

    Directory of Open Access Journals (Sweden)

    Lívia Darnay

    2016-07-01

    Full Text Available Our aim was to determine how 0.5-2 U/g non-inactivated mTG affects the pH development and apparent viscosity during fermentation. Furthermore we wished to examine how the enzyme addition could change protein structure, gel strength and sensory characteristics by healthy low-fat set-type yoghurt product. Therefore commercial mTG enzyme preparation was added in different concentrations (0.5-2.0 U/g, in 0.5 U/g steps to 1.5 % bovine milk simultaneously with DVS starter culture. Our study revealed that enzyme dosage (0.5-2 U/g protein had no impact on pH development and apparent viscosity during fermentation when manufacturing low-fat (1.5 % set-type yoghurt. The addition of mTG contributed to 38 % more whey retention with incorporation of β-casein, and caused 44 % higher gel strength up to a level of 1 U/g protein.

  9. Recombinant TgHSP70 Immunization Protects against Toxoplasma gondii Brain Cyst Formation by Enhancing Inducible Nitric Oxide Expression

    Directory of Open Access Journals (Sweden)

    Neide M. Silva

    2017-04-01

    Full Text Available Toxoplasma gondii is known to cause congenital infection in humans and animals and severe disease in immunocompromised individuals; consequently development of vaccines against the parasite is highly necessary. Under stress conditions, T. gondii expresses the highly immunogenic heat shock protein 70 (TgHSP70. Here, we assessed the protective efficacy of rTgHSP70 immunization combined with Alum in oral ME-49 T. gondii infection and the mechanisms involved on it. It was observed that immunized mice with rTgHSP70 or rTgHSP70 adsorbed in Alum presented a significantly reduced number of cysts in the brain that was associated with increased iNOS+ cell numbers in the organ, irrespective the use of the adjuvant. Indeed, ex vivo experiments showed that peritoneal macrophages pre-stimulated with rTgHSP70 presented increased NO production and enhanced parasite killing, and the protein was able to directly stimulate B cells toward antibody producing profile. In addition, rTgHSP70 immunization leads to high specific antibody titters systemically and a mixed IgG1/IgG2a response, with predominance of IgG1 production. Nonetheless, it was observed that the pretreatment of the parasite with rTgHSP70 immune sera was not able to control T. gondii internalization and replication by NIH fibroblast neither peritoneal murine macrophages, nor anti-rTgHSP70 antibodies were able to kill T. gondii by complement-mediated lysis, suggesting that these mechanisms are not crucial to resistance. Interestingly, when in combination with Alum, rTgHSP70 immunization was able to reduce inflammation in the brain of infected mice and in parallel anti-rTgHSP70 immune complexes in the serum. In conclusion, immunization with rTgHSP70 induces massive amounts of iNOS expression and reduced brain parasitism, suggesting that iNOS expression and consequently NO production in the brain is a protective mechanism induced by TgHSP70 immunization, therefore rTgHSP70 can be a good candidate for

  10. Clinical reevaluation of radioimmunological thyroglobulin (hTg) determination in follow-up of differentiated thyroid carcinoma

    International Nuclear Information System (INIS)

    Boettger, I.; Kanitz, W.; Pabst, W.H.

    1985-01-01

    A reevaluation of the clinical value of radioimmunological thyroglobulin (hTg) determination during follow-up of differentiated thyroid carcinoma, in general, confirms our previous results already published in 1980 and 1981. A total of 163 patients with differentiated thyroid carcinoma, 53 with papillary and 110 with follicular carcinoma, was studied up to January 1984. 586 sera are included in this study. The differentiation of suspicious from nonsuspicious findings was found to be based upon a cut-off concentration of 10 μg/l. Pathological findings were associated with hTg concentrations above 20 μg/l. Diagnostic accuracy was calculated to be between 95 and 97%, sensitivity of the method in comparison to be radioiodine whole-body scan was 98 versus 83%, respectively, and specificity 94%. At first 5 false negative and 6 false positive hTg findings have been obtained. 7.6% of the patients demonstrated endogeneous hTg antibodies by Boyden test. 7.7% of Boyden test negative sera showed an unacceptable hTg recovery of worse than +- 50%, which was possibly due to endogeneous antibodies. Again, endogenous TSH was able to stimulate hTg secretion in the form of elevated levels, yet did not affect the clinical diagnosis. Examples of the behaviour of hTg levels during follow-up are demonstrated. Specifically, the cases with false hTg findings are discussed. Basically, the conclusions are the same as in 1980 and 1981: hTg determination is able to replace the routinely performed radioiodine whole-body scan during follow-up, if once residual thyroid tissue and metastases have been excluded by means of radioiodine and an optimal follow-up program is used. (orig.) [de

  11. Cerebrospinal fluid neurofilament light chain as a biomarker of neurodegeneration in the Tg4510 and MitoPark mouse models

    DEFF Research Database (Denmark)

    Clement, Amalie; Mitchelmore, Cathy; Andersson, Daniel

    2017-01-01

    examined whether changes in NF-L levels in brain, plasma, and CSF reflect the changing disease status of preclinical models of neurodegeneration. Using Western Blot and ELISA we characterized NF-L and disease-related proteins in brain, CSF and plasma samples from Tg4510 mice (tauopathy/AD), MitoPark mice...... (PD), and their age-matched control littermates. We found that CSF NF-L clearly discriminates Tg4510 from control littermates, which was not observed for the MitoPark model. However, both Tg4510 and MitoPark showed altered expression and solubilization of NFs compared to control littermates. We found...

  12. FXIIIA and TGF-beta over-expression produces normal musculo-skeletal phenotype in TG2-/- mice.

    Science.gov (United States)

    Tarantino, U; Oliva, F; Taurisano, G; Orlandi, A; Pietroni, V; Candi, E; Melino, G; Maffulli, N

    2009-04-01

    Transglutaminase (TGs) enzymes and proteins crosslinking have for long time been implicated in the formation of hard tissue development, matrix maturation and mineralization. Among the TGs family members, in the context of connective tissue formation, TG2 and Factor XIII are expressed in cartilage by hypertrophic chondrocytes. Here, we analyse the morphological consequences of TG2 deficiency, during the development of skeletal elements. When TG2 is absent, there are not gross abnormalities in the development of the skeletal system, probably from compensatory mechanisms resulting in increased expression of FXIIIA and TGF-beta 1. In vivo other TGs may be involved in promoting chondrocytes and osteoblast differentiation and matrix mineralisation.

  13. Thermogravimetric study on the hydration of reactive magnesia and silica mixture at room temperature

    International Nuclear Information System (INIS)

    Jin, Fei; Al-Tabbaa, Abir

    2013-01-01

    Highlights: • The characteristics of reactive MgO vary significantly in terms of their impurity content and reactivity depending on their sources and calcination conditions. • The synthesis of magnesium silicate hydrate (MSH) is affected by the characteristics of the precursors, i.e., MgO and silica. • The reaction process in the MgO–SiO 2 –H 2 O system can be followed by TGA, and is essential to develop MSH-based materials. - Abstract: The synthesis of magnesium silicate hydrate (MSH), which has wide applications in both construction and environmental fields, has been studied for decades. However, it is known that the characteristics of magnesia (MgO) vary significantly depending on their calcination conditions, which is expected to affect their performance in the MgO–SiO 2 –H 2 O system. This paper investigated the effect of different MgO and silica sources on the formation of magnesium silicate hydrate (MSH) at room temperature. The hydration process was studied by mixing commercial reactive MgO and silica powders with water and curing for 1, 7 and 28 days. The hydration products were analysed with the help of X-ray diffraction (XRD) and thermogravimatric analysis (TGA). The results showed the continuous consumption of MgO and the existence of MSH and brucite and other minor phases such as magnesite and calcite. It is found that the Mg and Si sources have significant effect on the hydration process of MgO–SiO 2 –H 2 O system. The reaction degree is controlled by the availability of dissolved Mg and Si in the solution. The former is determined by the reactivity of MgO and the latter is related to the reactivity of the silica as well as the pH of the system

  14. License - Open TG-GATEs | LSDB Archive [Life Science Database Archive metadata

    Lifescience Database Archive (English)

    Full Text Available List Contact us Open TG-GATEs License License to Use This Database Last updated : 2012/05/24 You may use this database...scribed below. The Standard License specifies the license terms regarding the use of this database and the r...equirements you must follow in using this database. The Additional License specif...icense. Standard License The Standard License for this database is the license specified in the Creative Com...mons Attribution-Share Alike 2.1 Japan . If you use data from this database, plea

  15. Total skin high-dose-rate electron therapy dosimetry using TG-51

    International Nuclear Information System (INIS)

    Gossman, Michael S.; Sharma, Subhash C.

    2004-01-01

    An approach to dosimetry for total skin electron therapy (TSET) is discussed using the currently accepted TG-51 high-energy calibration protocol. The methodology incorporates water phantom data for absolute calibration and plastic phantom data for efficient reference dosimetry. The scheme is simplified to include the high-dose-rate mode conversion and provides support for its use, as it becomes more available on newer linear accelerators. Using a 6-field, modified Stanford technique, one may follow the process for accurate determination of absorbed dose

  16. Activation pattern of ACE2/Ang-(1-7) and ACE/Ang II pathway in course of heart failure assessed by multiparametric MRI in vivo in Tgαq*44 mice.

    Science.gov (United States)

    Tyrankiewicz, Urszula; Olkowicz, Mariola; Skórka, Tomasz; Jablonska, Magdalena; Orzylowska, Anna; Bar, Anna; Gonet, Michal; Berkowicz, Piotr; Jasinski, Krzysztof; Zoladz, Jerzy A; Smolenski, Ryszard T; Chlopicki, Stefan

    2018-01-01

    Here, we analyzed systemic (plasma) and local (heart/aorta) changes in ACE/ACE-2 balance in Tgαq*44 mice in course of heart failure (HF). Tgαq*44 mice with cardiomyocyte-specific Gαq overexpression and late onset of HF were analyzed at different age for angiotensin pattern in plasma, heart, and aorta using liquid chromatography/mass spectrometry, for progression of HF by in vivo magnetic resonance imaging under isoflurane anesthesia, and for physical activity by voluntary wheel running. Six-month-old Tgαq*44 mice displayed decreased ventricle radial strains and impaired left atrial function. At 8-10 mo, Tgαq*44 mice showed impaired systolic performance and reduced voluntary wheel running but exhibited preserved inotropic reserve. At 12 mo, Tgαq*44 mice demonstrated a severe impairment of basal cardiac performance and modestly compromised inotropic reserve with reduced voluntary wheel running. Angiotensin analysis in plasma revealed an increase in concentration of angiotensin-(1-7) in 6- to 10-mo-old Tgαq*44 mice. However, in 12- to 14-mo-old Tgαq*44 mice, increased angiotensin II was noted with a concomitant increase in Ang III, Ang IV, angiotensin A, and angiotensin-(1-10). The pattern of changes in the heart and aorta was also compatible with activation of ACE2, followed by activation of the ACE pathway. In conclusion, mice with cardiomyocyte Gαq protein overexpression develop HF that is associated with activation of the systemic and the local ACE/Ang II pathway. However, it is counterbalanced by a prominent ACE2/Ang-(1-7) activation, possibly allowing to delay decompensation. NEW & NOTEWORTHY Changes in ACE/ACE-2 balance were analyzed based on measurements of a panel of nine angiotensins in plasma, heart, and aorta of Tgαq*44 mice in relation to progression of heart failure (HF) characterized by multiparametric MRI and exercise performance. The early stage of HF was associated with upregulation of the ACE2/angiotensin-(1-7) pathway, whereas the end

  17. Long-term Treatment with Low-Dose Caffeine Worsens BPSD-Like Profile in 3xTg-AD Mice Model of Alzheimer’s Disease and Affects Mice with Normal Aging

    Directory of Open Access Journals (Sweden)

    Raquel Baeta-Corral

    2018-02-01

    Full Text Available Coffee or caffeine has recently been suggested as prophylaxis for dementia. Although memory problems are hallmarks of Alzheimer’s disease, this dementia is also characterized by neuropsychiatric symptoms called Behavioral and Psychological Symptoms of Dementia (BPSD. The impact of preventive/therapeutic strategies on both cognitive and non-cognitive symptoms can be addressed in the 3xTg-AD mice, since they exhibit cognitive but also BPSD-like profiles. Here, we studied the long-term effects of a low dose of caffeine in male 3xTg-AD mice and as compared to age-matched non-transgenic (NTg counterparts with normal aging. Animals were treated (water or caffeine in drinking water from adulthood (6 months of age until middle-aged (13 months of age, that in 3xTg-AD mice correspond to onset of cognitive impairment and advanced stages, respectively. The low caffeine dosing used (0.3 mg/ml was previously found to give a plasma concentration profile in mice roughly equivalent to that of a human coffee drinker. There were significant effects of caffeine on most behavioral variables, especially those related to neophobia and other anxiety-like behaviors, emotionality, and cognitive flexibility. The 3xTg-AD and NTg mice were differently influenced by caffeine. Overall, the increase of neophobia and other anxiety-related behaviors resulted in an exacerbation of BPSD-like profile in 3xTg-AD mice. Learning and memory, strongly influenced by anxiety in 3xTg-AD mice, got little benefit from caffeine, only shown after a detailed analysis of navigation strategies. The worsened pattern in NTg mice and the use of search strategies in 3xTg-AD mice make both groups more similar. Circadian motor activity showed genotype differences, which were found to be enhanced by caffeine. Selective effects of caffeine on NTg were found in the modulation of behaviors related to emotional profile and risk assessment. Caffeine normalized splenomegaly of 3xTg-AD mice, a physical

  18. Increased hippocampal excitability in the 3xTgAD mouse model for Alzheimer's disease in vivo.

    Directory of Open Access Journals (Sweden)

    Katherine E Davis

    Full Text Available Mouse Alzheimer's disease (AD models develop age- and region-specific pathology throughout the hippocampal formation. One recently established pathological correlate is an increase in hippocampal excitability in vivo. Hippocampal pathology also produces episodic memory decline in human AD and we have shown a similar episodic deficit in 3xTg AD model mice aged 3-6 months. Here, we tested whether hippocampal synaptic dysfunction accompanies this cognitive deficit by probing dorsal CA1 and DG synaptic responses in anaesthetized, 4-6 month-old 3xTgAD mice. As our previous reports highlighted a decline in episodic performance in aged control mice, we included aged cohorts for comparison. CA1 and DG responses to low-frequency perforant path stimulation were comparable between 3xTgAD and controls at both age ranges. As expected, DG recordings in controls showed paired-pulse depression; however, paired-pulse facilitation was observed in DG and CA1 of young and old 3xTgAD mice. During stimulus trains both short-latency (presumably monosynaptic: 'direct' and long-latency (presumably polysynaptic: 're-entrant' responses were observed. Facilitation of direct responses was modest in 3xTgAD animals. However, re-entrant responses in DG and CA1 of young 3xTgAD mice developed earlier in the stimulus train and with larger amplitude when compared to controls. Old mice showed less DG paired-pulse depression and no evidence for re-entrance. In summary, DG and CA1 responses to low-frequency stimulation in all groups were comparable, suggesting no loss of synaptic connectivity in 3xTgAD mice. However, higher-frequency activation revealed complex change in synaptic excitability in DG and CA1 of 3xTgAD mice. In particular, short-term plasticity in DG and CA1 was facilitated in 3xTgAD mice, most evidently in younger animals. In addition, re-entrance was facilitated in young 3xTgAD mice. Overall, these data suggest that the episodic-like memory deficit in 3xTgAD mice

  19. Follow-up of patients with thyroglobulin-antibodies : Rising Tg-Ab trend is a risk factor for recurrence of differentiated thyroid cancer

    NARCIS (Netherlands)

    de Meer, Siegrid G A; Vorselaars, Wessel M C M; Kist, Jakob W; Stokkel, Marcel P M; de Keizer, Bart; Valk, Gerlof D; Borel Rinkes, Inne H M; Vriens, Menno R

    2017-01-01

    PURPOSE: Differentiated thyroid cancer is the most common endocrine malignancy. Recurrences (5-20%) are the main reason for follow-up. Thyroglobulin (Tg) has proven to be an excellent disease marker, but thyroglobulin-antibodies (Tg-Ab) may interfere with Tg measurement, leading to over or

  20. Co-pyrolysis behavior of fermentation residues with woody sawdust by thermogravimetric analysis and a vacuum reactor.

    Science.gov (United States)

    Zheng, Yan; Zhang, Yimin; Xu, Jingna; Li, Xiayang; Charles Xu, Chunbao

    2017-12-01

    This study aimed at cost-effective utilization of fermentation residues (FR) from biogas project for bio-energy via co-pyrolysis of FR and woody sawdust (WS). In this study, a vacuum reactor was used to study the pyrolysis behaviors of individual and blend samples of FR and WS. Obvious synergistic effects were observed, resulting in a lower char yield but a higher gas yield. The presence of woody sawdust promoted the devolatilization of FR, and improved the syngas (H 2 and CO) content in the gaseous products. Compared to those of the char from pyrolysis of individual feedstock, co-pyrolysis of FR and WS in the vacuum reactor promoted the cracking reactions of large aromatic rings, enlarged the surface area and reduced the oxygenated groups of the resulted char. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. Botanical trash mixtures analyzed with near-infrared and attenuated total reflectance fourier transform spectroscopy and thermogravimetric analysis

    Science.gov (United States)

    Botanical cotton trash mixed with lint reduces cotton’s marketability and appearance. During cotton harvesting, ginning, and processing, trash size reduction occurs, thus complicating its removal and identification. This trash causes problems by increasing ends down in yarn formation and thus proce...

  2. Co-gasification of biosolids with biomass: Thermogravimetric analysis and pilot scale study in a bubbling fluidized bed reactor.

    Science.gov (United States)

    Yu, Ming Ming; Masnadi, Mohammad S; Grace, John R; Bi, Xiaotao T; Lim, C Jim; Li, Yonghua

    2015-01-01

    This work studied the feasibility of co-gasification of biosolids with biomass as a means of disposal with energy recovery. The kinetics study at 800°C showed that biomass, such as switchgrass, could catalyze the reactions because switchgrass ash contained a high proportion of potassium, an excellent catalyst for gasification. However, biosolids could also inhibit gasification due to interaction between biomass alkali/alkaline earth metals and biosolids clay minerals. In the pilot scale experiments, increasing the proportion of biosolids in the feedstock affected gasification performance negatively. Syngas yield and char conversion decreased from 1.38 to 0.47m(3)/kg and 82-36% respectively as the biosolids proportion in the fuel increased from 0% to 100%. Over the same range, the tar content increased from 10.3 to 200g/m(3), while the ammonia concentration increased from 1660 to 19,200ppmv. No more than 25% biosolids in the fuel feed is recommended to maintain a reasonable gasification. Copyright © 2014 Elsevier Ltd. All rights reserved.

  3. TG2 regulates the heat-shock response by the post-translational modification of HSF1.

    Science.gov (United States)

    Rossin, Federica; Villella, Valeria Rachela; D'Eletto, Manuela; Farrace, Maria Grazia; Esposito, Speranza; Ferrari, Eleonora; Monzani, Romina; Occhigrossi, Luca; Pagliarini, Vittoria; Sette, Claudio; Cozza, Giorgio; Barlev, Nikolai A; Falasca, Laura; Fimia, Gian Maria; Kroemer, Guido; Raia, Valeria; Maiuri, Luigi; Piacentini, Mauro

    2018-05-11

    Heat-shock factor 1 (HSF1) is the master transcription factor that regulates the response to proteotoxic stress by controlling the transcription of many stress-responsive genes including the heat-shock proteins. Here, we show a novel molecular mechanism controlling the activation of HSF1. We demonstrate that transglutaminase type 2 (TG2), dependent on its protein disulphide isomerase activity, triggers the trimerization and activation of HSF1 regulating adaptation to stress and proteostasis impairment. In particular, we find that TG2 loss of function correlates with a defect in the nuclear translocation of HSF1 and in its DNA-binding ability to the HSP70 promoter. We show that the inhibition of TG2 restores the unbalance in HSF1-HSP70 pathway in cystic fibrosis (CF), a human disorder characterized by deregulation of proteostasis. The absence of TG2 leads to an increase of about 40% in CFTR function in a new experimental CF mouse model lacking TG2. Altogether, these results indicate that TG2 plays a key role in the regulation of cellular proteostasis under stressful cellular conditions through the modulation of the heat-shock response. © 2018 The Authors.

  4. Leigh-Like Syndrome Due to Homoplasmic m.8993T>G Variant with Hypocitrullinemia and Unusual Biochemical Features Suggestive of Multiple Carboxylase Deficiency (MCD).

    Science.gov (United States)

    Balasubramaniam, Shanti; Lewis, B; Mock, D M; Said, H M; Tarailo-Graovac, M; Mattman, A; van Karnebeek, C D; Thorburn, D R; Rodenburg, R J; Christodoulou, J

    2017-01-01

    Leigh syndrome (LS), or subacute necrotizing encephalomyelopathy, is a genetically heterogeneous, relentlessly progressive, devastating neurodegenerative disorder that usually presents in infancy or early childhood. A diagnosis of Leigh-like syndrome may be considered in individuals who do not fulfil the stringent diagnostic criteria but have features resembling Leigh syndrome.We describe a unique presentation of Leigh-like syndrome in a 3-year-old boy with elevated 3-hydroxyisovalerylcarnitine (C5-OH) on newborn screening (NBS). Subsequent persistent plasma elevations of C5-OH and propionylcarnitine (C3) as well as fluctuating urinary markers were suggestive of multiple carboxylase deficiency (MCD). Normal enzymology and mutational analysis of genes encoding holocarboxylase synthetase (HLCS) and biotinidase (BTD) excluded MCD. Biotin uptake studies were normal excluding biotin transporter deficiency. His clinical features at 13 months of age comprised psychomotor delay, central hypotonia, myopathy, failure to thrive, hypocitrullinemia, recurrent episodes of decompensation with metabolic keto-lactic acidosis and an episode of hyperammonemia. Biotin treatment from 13 months of age was associated with increased patient activity, alertness, and attainment of new developmental milestones, despite lack of biochemical improvements. Whole exome sequencing (WES) analysis failed to identify any other variants which could likely contribute to the observed phenotype, apart from the homoplasmic (100%) m.8993T>G variant initially detected by mitochondrial DNA (mtDNA) sequencing.Hypocitrullinemia has been reported in patients with the m.8993T>G variant and other mitochondrial disorders. However, persistent plasma elevations of C3 and C5-OH have previously only been reported in one other patient with this homoplasmic mutation. We suggest considering the m.8993T>G variant early in the diagnostic evaluation of MCD-like biochemical disturbances, particularly when associated with

  5. Thermogravimetric study of thermal decontamination of soils polluted by hexachlorobenzene, 4-chlorobiphenyl, naphthalene, or n-decane.

    Science.gov (United States)

    Risoul, V; Pichon, C; Trouvé, G; Peters, W A; Gilot, P; Prado, G

    1999-02-15

    To determine decontamination behavior as affected by temperature, shallow beds of a clay-rich, a calcerous, and a sedimentary soil, artificially polluted with hexachlorobenzene, 4-chlorobiphenyl, naphthalene, or n-decane, were separately heated at 5 degrees C min-1 in a thermogravimetric analyzer. Temperatures for deep cleaning of the calcerous and the sedimentary soil increased with increasing boiling point (bp) of the aromatic contaminants, but removal efficiencies still approached 100% well below the bp. Decontamination rates were therefore modelled according to a pollutant evaporation-diffusion transport model. For the calcerous and sedimentary soils, this model reasonably correlated removal of roughly the first 2/3 of the naphthalene, but gave only fair predictions for hexachlorobenzene and 4-chlorobiphenyl. It was necessary to heat the clay soil above the aromatics bp to achieve high decontamination efficiencies. Weight loss data imply that for temperatures from near ambient to as much as 150 degrees C, interactions of each aromatic with the clay soil, or its decomposition products, result in lower net volatilization of the contaminated vs. neat clay. A similar effect was observed in heating calcerous soil polluted with hexachlorobenzene from near ambient to about 140 degrees C. Decontamination mechanisms remain to be established, although the higher temperatures needed to remove aromatics from the clay may reflect a more prominent role for surface desorption than evaporation. This would be consistent with our estimates that the clay can accommodate all of the initial pollutant loadings within a single surface monolayer, whereas the calcerous and sedimentary soils cannot.

  6. Effect of biopretreatment on thermogravimetric and chemical characteristics of corn stover by different white-rot fungi.

    Science.gov (United States)

    Yang, Xuewei; Zeng, Yelin; Ma, Fuying; Zhang, Xiaoyu; Yu, Hongbo

    2010-07-01

    The thermogravimetric and chemical characterization of corn stover biopretreated by three different species of white-rot fungi have been studied in this research. Results indicated that biopretreatment can optimize the thermal decomposition, decrease the reaction temperature and reduce the gas contamination (SO(x)), making the biomass pyrolysis more efficient and environmentally friendly. Biopretreatment can decrease the activation energy and reacting temperature of the hemicellulose and cellulose pyrolysis (up to 36 degrees C), shorten the temperature range of the active pyrolysis (up to 14 degrees C), and increase the thermal decomposition rate, greatly promoting the reaction and making the biomass pyrolysis easier to start and carry on. On the other hand, by biopretreatment, the sulphur content can decrease up to 46.15%, which can considerably reduce the inventory of SO(x) emission. Moreover, the mechanism of the biopretreatment was also explored that the deconstruction and depolymerization of the recalcitrant linkages of lignin and cellulose by biopretreatment can make the structure of biomass incompact and easier to be pyrolyzed. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

  7. Splitting CO2 with a ceria‐based redox cycle in a solar‐driven thermogravimetric analyzer

    Science.gov (United States)

    Takacs, M.; Ackermann, S.; Bonk, A.; Neises‐von Puttkamer, M.; Haueter, Ph.; Scheffe, J. R.; Vogt, U. F.

    2016-01-01

    Thermochemical splitting of CO2 via a ceria‐based redox cycle was performed in a solar‐driven thermogravimetric analyzer. Overall reaction rates, including heat and mass transport, were determined under concentrated irradiation mimicking realistic operation of solar reactors. Reticulated porous ceramic (RPC) structures and fibers made of undoped and Zr4+‐doped CeO2, were endothermally reduced under radiative fluxes of 1280 suns in the temperature range 1200–1950 K and subsequently re‐oxidized with CO2 at 950–1400 K. Rapid and uniform heating was observed for 8 ppi ceria RPC with mm‐sized porosity due to its low optical thickness and volumetric radiative absorption, while ceria fibers with μm‐sized porosity performed poorly due to its opacity to incident irradiation. The 10 ppi RPC exhibited higher fuel yield because of its higher sample density. Zr4+‐doped ceria showed increasing reduction extents with dopant concentration but decreasing specific CO yield due to unfavorable oxidation thermodynamics and slower kinetics. © 2016 American Institute of Chemical Engineers AIChE J, 63: 1263–1271, 2017 PMID:28405030

  8. Effect of biodegradation on thermogravimetric and chemical characteristics of hardwood and softwood by brown-rot fungus.

    Science.gov (United States)

    Gao, Zhenzhong; Fan, Qi; He, Zesen; Wang, Zhinan; Wang, Xiaobo; Sun, Jin

    2016-07-01

    The thermogravimetric and chemical characterization of hardwood Eucalyptus urophylla (Ep) and softwood Pinus massoniana (Mp) pretreated by brown-rot fungus Gloeophyllum trabeum were investigated. The results indicated that the brown-rot fungus pretreatment can optimize the thermal decomposition and decrease the initiation temperatures (8-11°C lower) of both the Ep and Mp pyrolysis. The mean activation energy values of the bio-treated samples were 29.7kJ/mol (for Ep) and 42.3kJ/mol (for Mp) lower than that of the un-treated samples at the conversion rate from 0.1 to 0.7 based on Flynn-Wall-Ozawa (FWO) method. After the bio-pretreatment, the required temperatures were lower (4-7°C) for the pyrolysis rates of hemicellulose and cellulose in Mp reaching maximum and termination. However, the situation was just the opposite for Ep. The variations in chemical properties of hydrogen bonding, as well as the relative changes in lignin/carbohydrate composition of both wood species were also examined. Copyright © 2016 Elsevier Ltd. All rights reserved.

  9. Effect of organic calcium compounds on combustion characteristics of rice husk, sewage sludge, and bituminous coal: thermogravimetric investigation.

    Science.gov (United States)

    Zhang, Lihui; Duan, Feng; Huang, Yaji

    2015-04-01

    Experiments were conducted in a thermogravimetric analyzer to assess the enhancement of combustion characteristics of different solid fuels blended with organic calcium compounds (OCCs). Rice husk, sewage sludge, and bituminous coal, and two OCC were used in this study. Effect of different mole ratios of calcium to sulfur (Ca/S ratio) on the combustion characteristics were also investigated. Results indicated that combustion performance indexes for bituminous coal impregnated by OCC were improved, however, an inverse trend was found for sewage sludge because sewage sludge has lower ignition temperature and higher volatile matter content compared to those of OCC. For rice husk, effect of added OCC on the combustion characteristics is not obvious. Different solid fuels show different combustion characteristics with increases of Ca/S ratio. The maximum combustion performance indexes appear at Ca/S ratios of 1:1, 2:1, and 3:1 for OCC blended with Shenhua coal, rice husk, and sewage sludge, respectively. Copyright © 2015 Elsevier Ltd. All rights reserved.

  10. Splitting CO2 with a ceria-based redox cycle in a solar-driven thermogravimetric analyzer.

    Science.gov (United States)

    Takacs, M; Ackermann, S; Bonk, A; Neises-von Puttkamer, M; Haueter, Ph; Scheffe, J R; Vogt, U F; Steinfeld, A

    2017-04-01

    Thermochemical splitting of CO 2 via a ceria-based redox cycle was performed in a solar-driven thermogravimetric analyzer. Overall reaction rates, including heat and mass transport, were determined under concentrated irradiation mimicking realistic operation of solar reactors. Reticulated porous ceramic (RPC) structures and fibers made of undoped and Zr 4+ -doped CeO 2 , were endothermally reduced under radiative fluxes of 1280 suns in the temperature range 1200-1950 K and subsequently re-oxidized with CO 2 at 950-1400 K. Rapid and uniform heating was observed for 8 ppi ceria RPC with mm-sized porosity due to its low optical thickness and volumetric radiative absorption, while ceria fibers with μm-sized porosity performed poorly due to its opacity to incident irradiation. The 10 ppi RPC exhibited higher fuel yield because of its higher sample density. Zr 4+ -doped ceria showed increasing reduction extents with dopant concentration but decreasing specific CO yield due to unfavorable oxidation thermodynamics and slower kinetics. © 2016 American Institute of Chemical Engineers , 63: 1263-1271, 2017.

  11. Molecular analysis of the eTG trinucleotide repeat in South African ...

    African Journals Online (AJOL)

    -4 When amplified, this trinucleotide repeat is responsible for DNA instability and molecular pathology. A similar mechanism of trinucleotide repeat expansion has been described in fragile X mental retardation syndrome. (CGG):·· spinobulbar muscular atrophy (CAG)' and, more. MRC Human Ecogenetics Research Unit, ...

  12. Long-term phenylbutyrate administration prevents memory deficits in Tg2576 mice by decreasing Abeta.

    Science.gov (United States)

    Ricobaraza, Ana; Cuadrado-Tejedor, Mar; Garcia-Osta, Ana

    2011-06-01

    Aberrations in protein folding, processing, and/or degradation are common features of neurodegenerative diseases, such as Alzheimer's disease (AD). Sodium 4-phenylbutyrate (PBA) is a well-known histone deacetylase inhibitor, which increases gene transcription of a number of genes, and also exerts neuroprotective effects. PBA acts as a chemical chaperone reducing the load of mutant or unfolded proteins during cellular stress. Previously, we reported that 5-week administration of PBA reinstated memory loss and dendritic spine densities in the Tg2576 mouse model of AD. In this study we reported that chronic administration of PBA, starting before the onset of disease symptoms (6 month-old) prevents age-related memory deficits in Tg2576 mice. The amelioration of the memory impairment is associated to a decrease in amyloid beta pathology and the glial fibrillary acidic protein (GFAP), suggesting that inflammation was reduced in PBA-treated animals. Together, the beneficial effects of PBA make it a promising agent for the prevention of AD.

  13. Cheese whey protein recovery by ultrafiltration through transglutaminase (TG) catalysis whey protein cross-linking.

    Science.gov (United States)

    Wen-Qiong, Wang; Lan-Wei, Zhang; Xue, Han; Yi, Lu

    2017-01-15

    In whey ultrafiltration (UF) production, two main problems are whey protein recovery and membrane fouling. In this study, membrane coupling protein transglutaminase (TG) catalysis protein cross-linking was investigated under different conditions to find out the best treatment. We found that the optimal conditions for protein recovery involved catalyzing whey protein cross-linking with TG (40U/g whey proteins) at 40°C for 60min at pH 5.0. Under these conditions, the recovery rate was increased 15-20%, lactose rejection rate was decreased by 10%, and relative permeate flux was increase 30-40% compared to the sample without enzyme treatment (control). It was noticeable that the total resistance and cake resistance were decreased after enzyme catalysis. This was mainly due to the increased particle size and decreased zeta potential. Therefore, membrane coupling enzyme catalysis protein cross-linking is a potential means for further use. Copyright © 2016. Published by Elsevier Ltd.

  14. SU-F-P-15: Report On AAPM TG 178 Gamma Knife Dosimetry and Quality Assurance

    Energy Technology Data Exchange (ETDEWEB)

    Goetsch, S [San Diego Medical Physics, Solana Beach, CA (United States)

    2016-06-15

    Purpose: AAPM Task Group 178 Gamma Stereotactic Radiosurgery Dosimetry and Quality Assurance was formed in August, 2008. The Task Group has 12 medical physicists, two physicians and two consultants. Methods: A round robin dosimetry intercomparison of proposed ionization chambers, electrometer and dosimetry phantoms was conducted over a 15 month period in 2011 and 2012 (Med Phys 42, 11, Nov, 2015). The data obtained at 9 institutions (with ten different Elekta Gamma Knife units) was analyzed by the lead author using several protocols. Results: The most consistent results were obtained using the Elekta ABS 16cm diameter phantom, with the TG-51 protocol modified as recommended by Alfonso et al (Med Phys 35, 11, Nov 2008). A key white paper (Med Phys, in press) sponsored by Elekta Corporation, was used to obtain correction factors for the ionization chambers and phantoms used in this intercomparison. Consistent results were obtained for both Elekta Gamma Knife Model 4C and Gamma Knife Perfexion units as measured with each of two miniature ionization chambers Conclusion: The full TG 178 report gives clinical history and background of gamma stereotactic radiosurgery, clinical examples and history, quality assurance recommendations and outline of possible dosimetry protocols. The report will be reviewed by the AAPM Working Group on Recommendations for Radiotherapy External Beam Quality Assurance and then by the AAPM Science Council before publication in Medical Physics. Consultant to Elekta, Inc.

  15. Tissue Transglutaminase (TG2)-Induced Inflammation in Initiation, Progression, and Pathogenesis of Pancreatic Cancer

    Energy Technology Data Exchange (ETDEWEB)

    Mehta, Kapil, E-mail: kmehta@mdanderson.org; Han, Amy [Department of Experimental Therapeutics, The University of Texas M. D. Anderson Cancer Center, Houston, TX 77030 (United States); Graduate School of Biomedical Sciences, The University of Texas Health Science Center, Houston, TX 77030 (United States)

    2011-02-25

    Pancreatic cancer (PC) is among the deadliest cancers, with a median survival of six months. It is generally believed that infiltrating PC arises through the progression of early grade pancreatic intraepithelial lesions (PanINs). In one model of the disease, the K-ras mutation is an early molecular event during progression of pancreatic cancer; it is followed by the accumulation of additional genetic abnormalities. This model has been supported by animal studies in which activated K-ras and p53 mutations produced metastatic pancreatic ductal adenocarcinoma in mice. According to this model, oncogenic K-ras induces PanIN formation but fails to promote the invasive stage. However, when these mice are subjected to caerulein treatment, which induces a chronic pancreatitis-like state and inflammatory response, PanINs rapidly progress to invasive carcinoma. These results are consistent with epidemiologic studies showing that patients with chronic pancreatitis have a much higher risk of developing PC. In line with these observations, recent studies have revealed elevated expression of the pro-inflammatory protein tissue transglutaminase (TG2) in early PanINs, and its expression increases even more as the disease progresses. In this review we discuss the implications of increased TG2 expression in initiation, progression, and pathogenesis of pancreatic cancer.

  16. WE-A-18A-01: TG246 On Patient Dose From Diagnostic Radiation

    Energy Technology Data Exchange (ETDEWEB)

    Supanich, M [Rush University Medical Center, Chicago, IL (United States); Dong, F [The Cleveland Clinic, Solon, OH (United States); Andersson, J [Umea University, Umea (Sweden); Pavlicek, W [Mayo Clinic Arizona, Scottsdale, AZ (United States); Bolch, W [University Florida, Gainesville, FL (United States); Fetterly, K [Mayo Clinic, Rochester, MN (United States)

    2014-06-15

    Radiation dose from diagnostic and interventional radiations continues to be a focus of the regulatory, accreditation and standards organizations in the US and Europe. A Joint AAPM/EFOMP effort has been underway in the past year — having the goal to assist the clinical medical physicist with communicating optional and varied approaches in estimating (and validating) patient dose. In particular, the tools provided by DICOM Radiation Dose Structured Reports, either by themselves or as part of a networked data repository of dose related information are a rich source of actionable information. The tools of the medical physicist have evolved to include using DICOM data in meaningful ways to look at patient dose with respect to imaging practices. In addition to how accurate or reproducible a dose value is (totally necessary and our traditional workspace) it is now being asked how reproducible (patient to patient, device to device) are the delivered doses (new tasking)? Clinical medical physicists are best equipped to assist our radiology and technologist colleagues with this effort. The purpose of this session is to review the efforts of TG246 - bringing forward a summary content of the TG246 Report including specific dose descriptors for CT and Fluoroscopy — particularly in a focus of leveraging the RDSR as a means for monitoring good practices ALARA. Additionally, rapidly evolving technologies for more refined dose estimates are now in use. These will be presented as they look to having highly patient specific dose estimates in automated use.

  17. Gender-Specific Neuroimmunoendocrine Response to Treadmill Exercise in 3xTg-AD Mice

    Directory of Open Access Journals (Sweden)

    Lydia Giménez-Llort

    2010-01-01

    Full Text Available The 3xTg-AD mouse develops a progressive Alzheimer's disease- (AD- like brain pathology that causes cognitive- and neuropsychiatric-like symptoms of dementia. Since its neuroimmunoendocrine axis is likewise impaired, this mouse is also useful for modelling complex age-related neurodegeneration. This study analyzed behavioral, physiological, neurochemical, pathological and immunoendocrine alterations in male and female 3xTg-AD mice and assayed the effects of a short therapy of forced physical exercise at the moderate pathology stage of 6 months of age. Gender effects were observed in most AD-related pathology and dysfunctions. Five weeks of treadmill training produced beneficial effects, such as the reduction of brain oxidative stress and GABA-A receptor dysfunction in males and improvement of sensorimotor function in females. In both sexes, exercise decreased the brain amyloid 42/40 ratio levels. The results highlight the importance of analyzing experimental therapies in both mouse model genders in order to improve our understanding of the disease and develop more appropriate therapies.

  18. SU-F-P-15: Report On AAPM TG 178 Gamma Knife Dosimetry and Quality Assurance

    International Nuclear Information System (INIS)

    Goetsch, S

    2016-01-01

    Purpose: AAPM Task Group 178 Gamma Stereotactic Radiosurgery Dosimetry and Quality Assurance was formed in August, 2008. The Task Group has 12 medical physicists, two physicians and two consultants. Methods: A round robin dosimetry intercomparison of proposed ionization chambers, electrometer and dosimetry phantoms was conducted over a 15 month period in 2011 and 2012 (Med Phys 42, 11, Nov, 2015). The data obtained at 9 institutions (with ten different Elekta Gamma Knife units) was analyzed by the lead author using several protocols. Results: The most consistent results were obtained using the Elekta ABS 16cm diameter phantom, with the TG-51 protocol modified as recommended by Alfonso et al (Med Phys 35, 11, Nov 2008). A key white paper (Med Phys, in press) sponsored by Elekta Corporation, was used to obtain correction factors for the ionization chambers and phantoms used in this intercomparison. Consistent results were obtained for both Elekta Gamma Knife Model 4C and Gamma Knife Perfexion units as measured with each of two miniature ionization chambers Conclusion: The full TG 178 report gives clinical history and background of gamma stereotactic radiosurgery, clinical examples and history, quality assurance recommendations and outline of possible dosimetry protocols. The report will be reviewed by the AAPM Working Group on Recommendations for Radiotherapy External Beam Quality Assurance and then by the AAPM Science Council before publication in Medical Physics. Consultant to Elekta, Inc

  19. Quantitative analysis of phases by x-ray diffraction and thermogravimetry in Cuban phosphorite ores

    International Nuclear Information System (INIS)

    Casanova Gomez, Abdel; Martinez Montalvo, Asor; Cilano Campos, Guillermo; Arostegui Aguirre, Miladys; Ferreiro Fernandez, Adalyz; Alonso Perez, Jose A.

    2016-01-01

    Phases analysis is performed by instrumental techniques X - ray diffraction and Thermal Analysis in two groups of samples of Cuban minerals carriers'phosphorus, candidates to reference materials. To this end, the variant of structural refinement of the diffraction pattern in the form of adjustment profile is applied, using the Full prof program of Juan Rodriguez-Carvajal. This analysis is the first step to develop the standard specification of these resources and classify them as phosphate rock and / or phospharite from their mass content. The statistical evaluation of the uncertainty of the quantitative analysis (standard deviation) was carried out in ten replicate samples of phosphate rock and eight of phosphate from the field Trinidad de Guedes. The qualitative phase analysis reflected the following phase composition: carbonate fluoroapatite (CFA), Calcite, Quartz and Halloysite (present only in the clayey granular phosphorite ore; FGA). By the method of setting pattern powder diffraction profile, the quantitative phase composition is reported in the sample FGA: 87 (2) % of CFA, 4 (1) % of Calcite, 1% Quartz, and 8 (3) % Halloysite. For granular limestone ore (FGC), the following contents were obtained: 87 (3) % Calcite, 8 (3) % of CFA and 5 (1) % Quartz: The obtained values are corroborated by Thermogravimetric Analysis (TG) through the calculation of the mass content of the thermally active phases (Calcite and CFA) in the range (27-10000 0 C), confirming the validity of the results of XRD. (Author)

  20. Thermogravimetric experiments with titanium

    International Nuclear Information System (INIS)

    Porter, L.J.; Longhurst, G.R.

    1991-02-01

    In the process of preparing for pyrophoricity experiments involving uranium, we conducted hydriding and air-exposure experiments on titanium. In these experiments the hydriding reactions and response to air-exposure was generally within the range expected based on work reported by others. One aberrant behavior was a sudden weight gain followed by a significant weight loss. We speculate that loss may be due to hydrogen evolution from the TiH 2 resulting from local heating by oxidation reactions. We verified that titanium is not pyrophoric at temperatures less than 750 degree C. 18 refs. 1 fig

  1. Novel insights into the functional metabolic impact of an apparent de novo m.8993T>G variant in the MT-ATP6 gene associated with maternally inherited form of Leigh Syndrome.

    Science.gov (United States)

    Uittenbogaard, Martine; Brantner, Christine A; Fang, ZiShui; Wong, Lee-Jun C; Gropman, Andrea; Chiaramello, Anne

    2018-03-27

    In this study, we report a novel perpective of metabolic consequences for the m.8993T>G variant using fibroblasts from a proband with clinical symptoms compatible with Maternally Inherited Leigh Syndrome (MILS). Definitive diagnosis was corroborated by mitochondrial DNA testing for the pathogenic variant m.8993T>G in MT-ATP6 subunit by Sanger sequencing. The long-range PCR followed by massively parallel sequencing method detected the near homoplasmic m.8993T>G variant at 83% in the proband's fibroblasts and at 0.4% in the mother's fibroblasts. Our results are compatible with very low levels of germline heteroplasmy or an apparent de novo mutation. Our mitochondrial morphometric analysis reveals severe defects in mitochondrial cristae structure in the proband's fibroblasts. Our live-cell mitochondrial respiratory analyses show impaired oxidative phosphorylation with decreased spare respiratory capacity in response to energy stress in the proband's fibroblasts. We detected a diminished glycolysis with a lessened glycolytic capacity and reserve, revealing a stunted ability to switch to glycolysis upon full inhibition of OXPHOS activities. This dysregulated energy reprogramming results in a defective interplay between OXPHOS and glycolysis during an energy crisis. Our study sheds light on the potential pathophysiologic mechanism leading to chronic energy crisis in this MILS patient harboring the m.8993T>G variant. Copyright © 2018 Elsevier Inc. All rights reserved.

  2. Heavy fuel oil pyrolysis and combustion: kinetics and evolved gases investigated by TGA-FTIR

    KAUST Repository

    Abdul Jameel, Abdul Gani; Han, Yunqing; Brignoli, Omar; Telalovic, Selvedin; Elbaz, Ayman M.; Im, Hong G.; Roberts, William L.; Sarathy, Mani

    2017-01-01

    investigated using non-isothermal thermo-gravimetric analysis (TGA) coupled with a Fourier-transform infrared (FTIR) spectrometer. TG and DTG (differential thermo-gravimetry) were used for the kinetic analysis and to study the mass loss characteristics due

  3. A Novel Form of Compensation in the Tg2576 Amyloid Mouse Model of Alzheimer’s Disease

    Science.gov (United States)

    Somogyi, Attila; Katonai, Zoltán; Alpár, Alán; Wolf, Ervin

    2016-01-01

    One century after its first description, pathology of Alzheimer’s disease (AD) is still poorly understood. Amyloid-related dendritic atrophy and membrane alterations of susceptible brain neurons in AD, and in animal models of AD are widely recognized. However, little effort has been made to study the potential effects of combined morphological and membrane alterations on signal transfer and synaptic integration in neurons that build up affected neural networks in AD. In this study spatial reconstructions and electrophysiological measurements of layer II/III pyramidal neurons of the somatosensory cortex from wild-type (WT) and transgenic (TG) human amyloid precursor protein (hAPP) overexpressing Tg2576 mice were used to build faithful segmental cable models of these neurons. Local synaptic activities were simulated in various points of the dendritic arbors and properties of subthreshold dendritic impulse propagation and predictors of synaptic input pattern recognition ability were quantified and compared in modeled WT and TG neurons. Despite the widespread dendritic degeneration and membrane alterations in mutant mouse neurons, surprisingly little, or no change was detected in steady-state and 50 Hz sinusoidal voltage transfers, current transfers, and local and propagation delays of PSPs traveling along dendrites of TG neurons. Synaptic input pattern recognition ability was also predicted to be unaltered in TG neurons in two different soma-dendritic membrane models investigated. Our simulations predict the way how subthreshold dendritic signaling and pattern recognition are preserved in TG neurons: amyloid-related membrane alterations compensate for the pathological effects that dendritic atrophy has on subthreshold dendritic signal transfer and integration in layer II/III somatosensory neurons of this hAPP mouse model for AD. Since neither propagation of single PSPs nor integration of multiple PSPs (pattern recognition) changes in TG neurons, we conclude that AD

  4. Comparison of time-gated surface-enhanced Raman spectroscopy (TG-SERS) and classical SERS based monitoring of Escherichia coli cultivation samples.

    Science.gov (United States)

    Kögler, Martin; Paul, Andrea; Anane, Emmanuel; Birkholz, Mario; Bunker, Alex; Viitala, Tapani; Maiwald, Michael; Junne, Stefan; Neubauer, Peter

    2018-06-08

    The application of Raman spectroscopy as a monitoring technique for bioprocesses is severely limited by a large background signal originating from fluorescing compounds in the culture media. Here we compare time-gated Raman (TG-Raman)-, continuous wave NIR-process Raman (NIR-Raman) and continuous wave micro-Raman (micro-Raman) approaches in combination with surface enhanced Raman spectroscopy (SERS) for their potential to overcome this limit. For that purpose, we monitored metabolite concentrations of Escherichia coli bioreactor cultivations in cell-free supernatant samples. We investigated concentration transients of glucose, acetate, AMP and cAMP at alternating substrate availability, from deficiency to excess. Raman and SERS signals were compared to off-line metabolite analysis of carbohydrates, carboxylic acids and nucleotides. Results demonstrate that SERS, in almost all cases, led to a higher number of identifiable signals and better resolved spectra. Spectra derived from the TG-Raman were comparable to those of micro-Raman resulting in well-discernable Raman peaks, which allowed for the identification of a higher number of compounds. In contrast, NIR-Raman provided a superior performance for the quantitative evaluation of analytes, both with and without SERS nanoparticles when using multivariate data analysis. This article is protected by copyright. All rights reserved. © 2018 American Institute of Chemical Engineers.

  5. Thermogravimetric, Calorimetric, and Structural Studies of the Co3 O4 /CoO Oxidation/Reduction Reaction

    Science.gov (United States)

    Unruh, Karl; Cichocki, Ronald; Kelly, Brian; Poirier, Gerald

    2015-03-01

    To better assess the potential of cobalt oxide for thermal energy storage (TES), the Co3O4/CoO oxidation/reduction reaction has been studied by thermogravimetric (TGA), calorimetric (DSC), and x-ray diffraction (XRD) measurements in N2 and atmospheric air environments. TGA measurements showed an abrupt mass loss of about 6.6% in both N2 and air, consistent with the stoichiometric reduction of Co3O4 to CoO and structural measurements. The onset temperature of the reduction of Co3O4 in air was only weakly dependent on the sample heating rate and occurred at about 910 °C. The onset temperature for the oxidation of CoO varied between about 850 and 875 °C for cooling rates between 1 and 20 °C/min, but complete re-conversion to Co3O4 could only be achieved at the slowest cooling rates. Due to the dependence of the rate constant on the oxygen partial pressure, the oxidation of Co3O4 in a N2 environment occurred at temperatures between about 775 and 825 °C for heating rates between 1 and 20 °C/min and no subsequent re-oxidation of the reduced Co3O4 was observed on cooling to room temperature. In conjunction with a measured transition heat of about 600 J/g of Co3O4, these measurements indicate that cobalt oxide is a viable TES material.

  6. Association of ADIPOQ +45T>G polymorphism with body fat mass and blood levels of soluble adiponectin and inflammation markers in a Mexican-Mestizo population

    Directory of Open Access Journals (Sweden)

    Guzman-Ornelas MO

    2012-10-01

    Full Text Available Milton-Omar Guzman-Ornelas,1 Efrain Chavarria-Avila,1 Jose-Francisco Munoz-Valle,1,2 Laura-Elizabeth Armas-Ramos,3 Jorge Castro-Albarran,3,4 Maria Elena Aguilar Aldrete,1,5 Edith Oregon-Romero,2 Monica Vazquez-Del Mercado,2 Rosa-Elena Navarro-Hernandez1–31Biomedical Sciences Doctorate Program, 2Department of Molecular Biology and Genomics, 3Master of Human Nutrition Program, University of Guadalajara, Guadalajara, Jalisco, México; 4HMIELM, Secretaria de Salud Jalisco, Guadalajara, Jalisco, Mexico; 5Department of Public Health, University of Guadalajara, Jalisco, MéxicoPurpose: Obesity is a disease with genetic susceptibility characterized by an increase in storage and irregular distribution of body fat. In obese patients, the decrease in the Adiponectin gene (ADIPOQ expression has been associated with a systemic low-grade inflammatory state. Our aim was to investigate the relationship between ADIPOQ +45T>G gene simple nucleotide polymorphism (SNP rs2241766 with serum adiponectin (sAdiponectin, distribution of body fat storage, and inflammation markers.Subjects and methods: In this cross-sectional study, 242 individuals from Western Mexico characterized as Mexican-Mestizo and classified by body mass index (BMI, were included. Anthropometrics, body composition, body fat distribution, and inflammation markers were measured by routine methods. Genotypes were characterized using the polymerase chain reaction-restriction fragment length polymorphism (PCR-RFLP technique and sAdiponectin by the ELISA method. A P-value <0.05 was considered the statistically significant threshold.Results: sAdiponectin is associated with BMI (P < 0.001 and the genotypes (P < 0.001 to 0.0046 GG (8169 ± 1162 ng/mL, TG (5189 ± 501 ng/mL, and TT (3741 ± 323 ng/mL, but the SNP ADIPOQ +45T.G is not associated with BMI. However, the detailed analysis showed association of this SNP with a pattern of fat distribution and correlations (P < 0.05 with inflammation markers and

  7. Structure investigations on zirconium phosphate preparates by means of DTA, ETA, and TG

    International Nuclear Information System (INIS)

    Herbell, J.D.; Specht, S.; Born, H.J.

    1976-01-01

    The simultanous DTA, ETA and TG inorganic ion exchanger based on zirconium phosphate enables the clear interpretation of the effects occuring. In particular it can be seen that the fast transition in amorphous preparates at high temperature of a badly defined form of pyrophosphate into the cubic crystalline substances, however a measurable energy release by means of DTA is not observed due to the slight mobility of the atoms in the crystal lattice. This effect on the other hand may be seen using ETA. In addition, an exothermal reaction occuring in some preparates, especially in cation charged ones, was traced back to the forming of part-crystalline structures which could be especially fast and sensitively characterized using DTA. (orig.) [de

  8. Solid-phase microextraction for bioconcentration studies according to OECD TG 305

    Energy Technology Data Exchange (ETDEWEB)

    Duering, Rolf-Alexander; Boehm, Leonard [Land Use and Nutrition (IFZ) Justus Liebig University Giessen, Institute of Soil Science and Soil Conservation, Research Centre for BioSystems, Giessen (Germany); Schlechtriem, Christian [Fraunhofer Institute for Molecular Biology and Applied Ecology (IME), Schmallenberg (Germany)

    2012-12-15

    An important aim of the European Community Regulation on chemicals and their safe use is the identification of (very) persistent, (very) bioaccumulative, and toxic substances. In other regulatory chemical safety assessments (pharmaceuticals, biocides, pesticides), the identification of such (very) persistent, (very) bioaccumulative, and toxic substances is of increasing importance. Solid-phase microextraction is especially capable of extracting total water concentrations as well as the freely dissolved fraction of analytes in the water phase, which is available for bioconcentration in fish. However, although already well established in environmental analyses to determine and quantify analytes mainly in aqueous matrices, solid-phase microextraction is still a rather unusual method in regulatory ecotoxicological research. Here, the potential benefits and drawbacks of solid-phase microextraction are discussed as an analytical routine approach for aquatic bioconcentration studies according to OECD TG 305, with a special focus on the testing of hydrophobic organic compounds characterized by log K{sub OW}> 5. (orig.)

  9. Synthesis, characterization and TG-DSC study of cadmium halides adducts with caffeine

    Energy Technology Data Exchange (ETDEWEB)

    Farias, Robson F. de; Silva, Ademir O. da; Silva, Umberto G. da

    2003-11-28

    The synthesis, characterization and TG-DSC study of the compounds CdX{sub 2}{center_dot}ncaff, for which X: Cl, Br and I; n=1 and 2 and caff: caffeine is reported. It is verified that caffeine is coordinated through more than one coordination site, despite the fact that the nitrogen of the imidazole ring is the main coordination site. The following thermal stability trend is observed: Cl>Br>I and monoadducts are more stable than bisadducts. The thermal degradation (td) enthalpies have the values (kJ mol{sup -1}): 58.2 and 71.5; 74.9 and 91.4; 31.1 and 47.5 for Cl, Br and I mono and bisadducts, respectively.

  10. Investigation of hydropyrolysis behaviour of Shenmu macerals by TG-MS

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Q.; Li, W.; Chen, H.; Li, B. [Analysis and Test Center, Shandong Academy of Sciences, Jinan (China)

    2004-12-01

    The hydropyrolysis characteristics of Shenmu coal and its macerals were investigated using TG-151 thermo balance, and the evolved gases were on-line analyzed by mass spectroscopy. The results show that vitrinite has higher volatile yield, maximum weight loss rate and lower peak temperature. Vitrinite produces more C{sub 1} - C{sub 4} lighter hydrocarbons and C{sub 5} - C{sub 8} aromatic hydrocarbons than inertinite. Vitrinite has a higher water yield, which is consistent with that the vitrinite has higher phenolic-OH content. The difference in the evolved gases and water between pyrolysis and hydropyrolysis shows the effect of hydrogenation and hydrocracking during hydropyolysis. 11 refs., 4 figs., 1 tab.

  11. Dynamic traffic grooming with Spectrum Engineering (TG-SE) in flexible grid optical networks

    Science.gov (United States)

    Yu, Xiaosong; Zhao, Yongli; Zhang, Jiawei; Wang, Jianping; Zhang, Guoying; Chen, Xue; Zhang, Jie

    2015-12-01

    Flexible grid has emerged as an evolutionary technology to satisfy the ever increasing demand for higher spectrum efficiency and operational flexibility. To optimize the spectrum resource utilization, this paper introduces the concept of Spectrum Engineering in flex-grid optical networks. The sliceable optical transponder has been proposed to offload IP traffic to the optical layer and reduce the number of IP router ports and transponders. We discuss the impact of sliceable transponder in traffic grooming and propose several traffic-grooming schemes with Spectrum Engineering (TG-SE). Our results show that there is a tradeoff among different traffic grooming policies, which should be adopted based on the network operator's objectives. The proposed traffic grooming with Spectrum Engineering schemes can reduce OPEX as well as increase spectrum efficiency by efficiently utilizing the bandwidth variability and capability of sliceable optical transponders.

  12. TG study on pyrolysis of biomass and its three components under syngas

    Energy Technology Data Exchange (ETDEWEB)

    Gang Wang; Wen Li; Baoqing Li; Haokan Chen [Chinese Academy of Sciences, Taiyuan (China). State Key Laboratory of Coal Conversion

    2008-04-15

    Pyrolysis of sawdust and its three components (cellulose, hemicellulose and lignin) were performed in a thermogravimetric analyzer (TGA92) under syngas and hydrogen. The effect of different heating rates (5, 10, 15 and 20{sup o}C/min) on the pyrolysis of these samples were examined. The pyrolysis tests of the synthesized samples (a mixture of the three components with different ratios) were also done under syngas. The distributed activation energy model (DAEM) was used to study the pyrolysis kinetics. It is found that syngas could replace hydrogen in hydropyrolysis process of biomass. Among the three components, hemicellulose would be the easiest one to be pyrolyzed and then would be cellulose, while lignin would be the most difficult one. Heating rate could not only affect the temperature at which the highest weight loss rate reached, but also affect the maximum value of weight loss rate. Both lignin and hemicellulose used in the experiments could affect the pyrolysis characteristic of cellulose while they could not affect each other obviously in the pyrolysis process. Values of k{sub 0} (frequency factor) change very greatly with different E (activation energy) values. The E values of sawdust range from 161.9 to 202.3 kJ/mol, which is within the range of activation energy values for cellulose, hemicellulose and lignin. 22 refs., 4 figs., 2 tabs.

  13. Technical Report: TG-142 compliant and comprehensive quality assurance tests for respiratory gating

    Energy Technology Data Exchange (ETDEWEB)

    Woods, Kyle [Department of Radiation Oncology, Ohio State University, Columbus, Ohio 43210 (United States); Rong, Yi, E-mail: yrong@ucdavis.edu [Department of Radiation Oncology, University of California Davis Comprehensive Cancer Center, Sacramento, California 95817 (United States)

    2015-11-15

    Purpose: To develop and establish a comprehensive gating commissioning and quality assurance procedure in compliance with TG-142. Methods: Eight Varian TrueBeam Linacs were used for this study. Gating commissioning included an end-to-end test and baseline establishment. The end-to-end test was performed using a CIRS dynamic thoracic phantom with a moving cylinder inside the lung, which was used for carrying both optically simulated luminescence detectors (OSLDs) and Gafchromic EBT2 films while the target is moving, for a point dose check and 2D profile check. In addition, baselines were established for beam-on temporal delay and calibration of the surrogate, for both megavoltage (MV) and kilovoltage (kV) beams. A motion simulation device (MotionSim) was used to provide periodic motion on a platform, in synchronizing with a surrogate motion. The overall accuracy and uncertainties were analyzed and compared. Results: The OSLD readings were within 5% compared to the planned dose (within measurement uncertainty) for both phase and amplitude gated deliveries. Film results showed less than 3% agreement to the predicted dose with a standard sinusoid motion. The gate-on temporal accuracy was averaged at 139 ± 10 ms for MV beams and 92 ± 11 ms for kV beams. The temporal delay of the surrogate motion depends on the motion speed and was averaged at 54.6 ± 3.1 ms for slow, 24.9 ± 2.9 ms for intermediate, and 23.0 ± 20.1 ms for fast speed. Conclusions: A comprehensive gating commissioning procedure was introduced for verifying the output accuracy and establishing the temporal accuracy baselines with respiratory gating. The baselines are needed for routine quality assurance tests, as suggested by TG-142.

  14. AbetaPP induces cdk5-dependent tau hyperphosphorylation in transgenic mice Tg2576.

    Science.gov (United States)

    Otth, Carola; Concha, Ilona I; Arendt, Thomas; Stieler, Jens; Schliebs, Reinhard; González-Billault, Christian; Maccioni, Ricardo B

    2002-10-01

    Previous studies of Abeta-induced neuronal damage of hippocampal cells in culture have provided strong evidence that deregulation of the Cdk5/p35 kinase system is involved in the neurodegeneration pathway. Cdk5 inhibitors and antisense probes neuroprotected hippocampal cells against the neurotoxic action of Abeta. To further investigate the mechanisms underlying the participation of Cdk5 in neuronal degeneration, the transgenic mouse containing the Swedish mutations, Tg2576, was used as an animal model. Immunocytochemical studies using anti-Abeta(1-17) antibody evidenced the presence of labeled small-clustered core plaques in the hippocampus and cortex of 18-month-old transgenic mice brains. The loss of granular cells without a compressed appearance was detected in the vicinity of the cores in the dentate gyrus of the hippocampus. Immunostaining of Tg2576 brain sections with antibodies AT8, PHF1 and GFAP labeled punctuate dystrophic neurites in and around the amyloid core. Reactive astrogliosis around the plaques in the hippocampus was also observed. Studies at the molecular level showed differences in the expression of the truncated Cdk5 activator p25 in the transgenic animal, as compared with wild type controls. However no differences in Cdk5 levels were detected, thus corroborating previous cellular findings. Interestingly, hyperphosphorylated tau epitopes were substantially increased as assessed with the AT8 and PHF1 antibodies, in agreement with the observation of a p25 increase in the transgenic animal. These observations strongly suggest that the increased exposure of Alzheimer's type tau phosphoepitopes in the transgenic mice correlated with deregulation of Cdk5 leading to an increase in p25 levels. These studies also provide further evidence on the links between extraneuronal amyloid deposition and tau pathology.

  15. TH-B-204-03: TG-199: Implanted Markers for Radiation Treatment Verification

    International Nuclear Information System (INIS)

    Wang, Z.

    2016-01-01

    Implanted markers as target surrogates have been widely used for treatment verification, as they provide safe and reliable monitoring of the inter- and intra-fractional target motion. The rapid advancement of technology requires a critical review and recommendation for the usage of implanted surrogates in current field. The symposium, also reporting an update of AAPM TG 199 - Implanted Target Surrogates for Radiation Treatment Verification, will be focusing on all clinical aspects of using the implanted target surrogates for treatment verification and related issues. A wide variety of markers available in the market will be first reviewed, including radiopaque markers, MRI compatible makers, non-migrating coils, surgical clips and electromagnetic transponders etc. The pros and cons of each kind will be discussed. The clinical applications of implanted surrogates will be presented based on different anatomical sites. For the lung, we will discuss gated treatments and 2D or 3D real-time fiducial tracking techniques. For the prostate, we will be focusing on 2D-3D, 3D-3D matching and electromagnetic transponder based localization techniques. For the liver, we will review techniques when patients are under gating, shallow or free breathing condition. We will review techniques when treating challenging breast cancer as deformation may occur. Finally, we will summarize potential issues related to the usage of implanted target surrogates with TG 199 recommendations. A review of fiducial migration and fiducial derived target rotation in different disease sites will be provided. The issue of target deformation, especially near the diaphragm, and related suggestions will be also presented and discussed. Learning Objectives: Knowledge of a wide variety of markers Knowledge of their application for different disease sites Understand of issues related to these applications Z. Wang: Research funding support from Brainlab AG Q. Xu: Consultant for Accuray; Q. Xu, I am a consultant

  16. TH-B-204-00: Implanted Markers for Radiation Therapy and TG 199 Update

    International Nuclear Information System (INIS)

    2016-01-01

    Implanted markers as target surrogates have been widely used for treatment verification, as they provide safe and reliable monitoring of the inter- and intra-fractional target motion. The rapid advancement of technology requires a critical review and recommendation for the usage of implanted surrogates in current field. The symposium, also reporting an update of AAPM TG 199 - Implanted Target Surrogates for Radiation Treatment Verification, will be focusing on all clinical aspects of using the implanted target surrogates for treatment verification and related issues. A wide variety of markers available in the market will be first reviewed, including radiopaque markers, MRI compatible makers, non-migrating coils, surgical clips and electromagnetic transponders etc. The pros and cons of each kind will be discussed. The clinical applications of implanted surrogates will be presented based on different anatomical sites. For the lung, we will discuss gated treatments and 2D or 3D real-time fiducial tracking techniques. For the prostate, we will be focusing on 2D-3D, 3D-3D matching and electromagnetic transponder based localization techniques. For the liver, we will review techniques when patients are under gating, shallow or free breathing condition. We will review techniques when treating challenging breast cancer as deformation may occur. Finally, we will summarize potential issues related to the usage of implanted target surrogates with TG 199 recommendations. A review of fiducial migration and fiducial derived target rotation in different disease sites will be provided. The issue of target deformation, especially near the diaphragm, and related suggestions will be also presented and discussed. Learning Objectives: Knowledge of a wide variety of markers Knowledge of their application for different disease sites Understand of issues related to these applications Z. Wang: Research funding support from Brainlab AG Q. Xu: Consultant for Accuray; Q. Xu, I am a consultant

  17. Furoquinoline Alkaloids and Methoxyflavones from the Stem Bark of Melicope madagascariensis (Baker T.G. Hartley

    Directory of Open Access Journals (Sweden)

    Vincent E. Rasamison

    2016-09-01

    Full Text Available Abstract Melicope madagascariensis (Rutaceae is an endemic plant species of Madagascar that was first classified as a member of the genus Euodia J. R. & G. Forst (Rutaceae under the scientific name Euodia madagascariensis Baker. Based on morphological characteristics, Thomas Gordon Hartley taxonomically revised E. madagascariensis Baker to be M. madagascariensis (Baker T.G. Hartley. Chemotaxonomical studies have long been used to help the identification and confirmation of taxonomical classification of plant species and botanicals. Aiming to find more evidences to support the taxonomical revision performed on E. madagascariensis, we carried out phytochemical investigation of two samples of the plant. Fractionation of the ethanol extracts prepared from two stem bark samples of M. madagascariensis (Baker T.G. Hartley led to the isolation of seven known furoquinoline alkaloids 1–7 and two known methoxyflavones 8 and 9. The presence of furoquinoline alkaloids and methoxyflavones in the title species is in agreement with its taxonomic transfer from Euodia to Melicope. Antiprotozoal evaluation of the isolated compounds showed that 6-methoxy-7-hydroxydictamnine (heliparvifoline, 3 showed weak antimalarial activity (IC50 = 35 µM against the chloroquine-resistant strain Dd2 of Plasmodium falciparum. Skimmianine (4 displayed moderate cytotoxicity with IC50 value of 1.5 µM against HT-29 colon cancer cell line whereas 3,5-dihydroxy-3′,4′,7-trimethoxyflavone (9 was weakly active in the same assay (IC50 = 13.9 µM. Graphical Abstract

  18. Technical Report: TG-142 compliant and comprehensive quality assurance tests for respiratory gating

    International Nuclear Information System (INIS)

    Woods, Kyle; Rong, Yi

    2015-01-01

    Purpose: To develop and establish a comprehensive gating commissioning and quality assurance procedure in compliance with TG-142. Methods: Eight Varian TrueBeam Linacs were used for this study. Gating commissioning included an end-to-end test and baseline establishment. The end-to-end test was performed using a CIRS dynamic thoracic phantom with a moving cylinder inside the lung, which was used for carrying both optically simulated luminescence detectors (OSLDs) and Gafchromic EBT2 films while the target is moving, for a point dose check and 2D profile check. In addition, baselines were established for beam-on temporal delay and calibration of the surrogate, for both megavoltage (MV) and kilovoltage (kV) beams. A motion simulation device (MotionSim) was used to provide periodic motion on a platform, in synchronizing with a surrogate motion. The overall accuracy and uncertainties were analyzed and compared. Results: The OSLD readings were within 5% compared to the planned dose (within measurement uncertainty) for both phase and amplitude gated deliveries. Film results showed less than 3% agreement to the predicted dose with a standard sinusoid motion. The gate-on temporal accuracy was averaged at 139 ± 10 ms for MV beams and 92 ± 11 ms for kV beams. The temporal delay of the surrogate motion depends on the motion speed and was averaged at 54.6 ± 3.1 ms for slow, 24.9 ± 2.9 ms for intermediate, and 23.0 ± 20.1 ms for fast speed. Conclusions: A comprehensive gating commissioning procedure was introduced for verifying the output accuracy and establishing the temporal accuracy baselines with respiratory gating. The baselines are needed for routine quality assurance tests, as suggested by TG-142

  19. TH-B-204-03: TG-199: Implanted Markers for Radiation Treatment Verification

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Z. [Duke University Medical Center (United States)

    2016-06-15

    Implanted markers as target surrogates have been widely used for treatment verification, as they provide safe and reliable monitoring of the inter- and intra-fractional target motion. The rapid advancement of technology requires a critical review and recommendation for the usage of implanted surrogates in current field. The symposium, also reporting an update of AAPM TG 199 - Implanted Target Surrogates for Radiation Treatment Verification, will be focusing on all clinical aspects of using the implanted target surrogates for treatment verification and related issues. A wide variety of markers available in the market will be first reviewed, including radiopaque markers, MRI compatible makers, non-migrating coils, surgical clips and electromagnetic transponders etc. The pros and cons of each kind will be discussed. The clinical applications of implanted surrogates will be presented based on different anatomical sites. For the lung, we will discuss gated treatments and 2D or 3D real-time fiducial tracking techniques. For the prostate, we will be focusing on 2D-3D, 3D-3D matching and electromagnetic transponder based localization techniques. For the liver, we will review techniques when patients are under gating, shallow or free breathing condition. We will review techniques when treating challenging breast cancer as deformation may occur. Finally, we will summarize potential issues related to the usage of implanted target surrogates with TG 199 recommendations. A review of fiducial migration and fiducial derived target rotation in different disease sites will be provided. The issue of target deformation, especially near the diaphragm, and related suggestions will be also presented and discussed. Learning Objectives: Knowledge of a wide variety of markers Knowledge of their application for different disease sites Understand of issues related to these applications Z. Wang: Research funding support from Brainlab AG Q. Xu: Consultant for Accuray; Q. Xu, I am a consultant

  20. TH-B-204-00: Implanted Markers for Radiation Therapy and TG 199 Update

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2016-06-15

    Implanted markers as target surrogates have been widely used for treatment verification, as they provide safe and reliable monitoring of the inter- and intra-fractional target motion. The rapid advancement of technology requires a critical review and recommendation for the usage of implanted surrogates in current field. The symposium, also reporting an update of AAPM TG 199 - Implanted Target Surrogates for Radiation Treatment Verification, will be focusing on all clinical aspects of using the implanted target surrogates for treatment verification and related issues. A wide variety of markers available in the market will be first reviewed, including radiopaque markers, MRI compatible makers, non-migrating coils, surgical clips and electromagnetic transponders etc. The pros and cons of each kind will be discussed. The clinical applications of implanted surrogates will be presented based on different anatomical sites. For the lung, we will discuss gated treatments and 2D or 3D real-time fiducial tracking techniques. For the prostate, we will be focusing on 2D-3D, 3D-3D matching and electromagnetic transponder based localization techniques. For the liver, we will review techniques when patients are under gating, shallow or free breathing condition. We will review techniques when treating challenging breast cancer as deformation may occur. Finally, we will summarize potential issues related to the usage of implanted target surrogates with TG 199 recommendations. A review of fiducial migration and fiducial derived target rotation in different disease sites will be provided. The issue of target deformation, especially near the diaphragm, and related suggestions will be also presented and discussed. Learning Objectives: Knowledge of a wide variety of markers Knowledge of their application for different disease sites Understand of issues related to these applications Z. Wang: Research funding support from Brainlab AG Q. Xu: Consultant for Accuray; Q. Xu, I am a consultant

  1. Thermodynamic study of ibuprofen by adiabatic calorimetry and thermal analysis

    International Nuclear Information System (INIS)

    Xu Fen; Sun Lixian; Tan Zhicheng; Liang Jianguo; Li Ruilian

    2004-01-01

    Molar heat capacities of ibuprofen were precisely measured with a small sample precision automated adiabatic calorimeter over the temperature range from 80 to 400 K. The polynomial functions of C p,m (J K -1 mol -1 ) versus T were established on the heat capacity measurements by means of the least fitting square method. The functions are as follows: for solid ibuprofen, at the temperature range of 79.105 K≤T≤333.297 K, C p,m =144.27+77.046X+3.5171X 2 +10.925X 3 +11.224X 4 , where X=(T-206.201)/127.096; for liquid ibuprofen, at the temperature range of 353.406 K≤T≤378.785 K, C p,m =325.79+8.9696X-1.6073X 2 -1.5145X 3 , where X=(T-366.095)/12.690. A fusion transition at T=348.02 K was found from the C p -T curve. The molar enthalpy and entropy of the fusion transition were determined to be 26.65 kJ mol -1 and 76.58 J mol -1 K -1 , respectively. The thermodynamic functions on the base of the reference temperature of 298.15 K, (H T -H 298.15 ) and (S T -S 298.15 ), were derived. Thermal characteristic of ibuprofen was studied by thermo-gravimetric analysis (TG-DTG) and differential scanning calorimeter (DSC). The temperature of fusion, the molar enthalpy and entropy of fusion obtained by DSC were well consistent with those obtained by adiabatic calorimeter. The evaporation process of ibuprofen was investigated further by TG and DTG, and the activation energy of the evaporation process was determined to be 80.3±1.4 kJ mol -1

  2. Thermal analysis of RFETS SS and C

    International Nuclear Information System (INIS)

    Korinko, P.S.

    2000-01-01

    In support of the gas generation test program (GGTP) for the 9975 shipping container, thermogravimetric analysis (TGA) was conducted. The objective of this activity was to determine the moisture content as an input to the gas generation model

  3. Comportamento térmico e caracterização morfológica das fibras de mesocarpo e caroço do açaí (Euterpe oleracea Mart. Thermogravimetric evaluation of açaí fruit (Euterpe oleracea Mart. agro industry waste

    Directory of Open Access Journals (Sweden)

    Maria Alice Martins

    2009-12-01

    Full Text Available A agroindústria do açaí gera uma grande quantidade de resíduos, constituída de caroços e fibras, o que é um grave problema ambiental e de saúde pública. O objetivo deste estudo foi estudar as fibras do mesocarpo e o caroço do fruto do açaí para sua utilização em materiais compósitos. As amostras foram caracterizadas usando análise por termogravimetria (TG/DTG em atmosferas inerte e oxidativa, microscopia eletrônica de varredura e microscopia óptica. As fibras apresentaram boa estabilidade térmica até 230 ºC e um processo de degradação em atmosfera inerte em três etapas. Em atmosfera oxidativa, as fibras apresentaram menor estabilidade térmica e uma mudança no processo de degradação de três para quatro etapas. os resultados da análise térmica do caroço mostraram um comportamento térmico similar ao da fibra. A microscopia mostrou que as fibras presentes no fruto do açaí recobrem o caroço e possuem morfologia irregular com a presença de células do parênquima na sua superfície. O comportamento térmico das fibras do açaí é semelhante ao de outras fibras vegetais já utilizadas industrialmente na área de compósitos poliméricos, o que abre novas e promissoras áreas para sua utilização.The açaí fruit agro industry produces a large amount of waste, mainly seeds and fibers, which is a serious environmental and public health problem. The aim of this work is to study the mesocarp fibers and the açaí fruit seed to use in composite materials. The samples have been characterized by using thermogravimetric analysis (TGA/DTG in inert and thermo-oxidative atmospheres, scanning electron and optical microscopy. The fibers have shown good stability until 230ºC and a threedegradation step process in inert atmosphere. In oxidative atmosphere, the fibers presented a decrease in thermal stability and a change in the decomposition process from three to four steps. For the seeds, a similar behavior was observed

  4. Thermogravimetric and magneticproperties of Ni1-X Zn xFe2O4 nanoparticles synthesized by coprecipitation

    Directory of Open Access Journals (Sweden)

    Kandasamy Velmurugan

    2009-01-01

    Full Text Available Ni1-xZn xFe2O4 (x = 0 to 1 nanoparticles of size less than 9 nm were prepared by a chemical coprecipitation method which could be used for ferrofluid preparation. XRD, VSM and DTA-TG (STA were used to study the effect of variation in Zn substitution and its influence on particle size, magnetic properties such as M S, H C and Curie temperature, as well as on the water content. ICP was used to estimate Ni, Zn and Fe concentrations. The average crystallite size (DaveXR of the particles was found to decrease from 8.95 to 6.92 nm with increasing zinc substitution. The lattice constant (a o increased with increasing zinc substitution. The specific saturation magnetization (M S of the particles was measured at room temperature. Magnetic parameters such as M S, Hc, and Mr were found to decrease with increasing zinc substitution. Estimation of the water content, which varies the Zn concentration, plays a vital role for the correct determination of cation contents. The Curie temperature was found to decrease with increasing zinc substitution.

  5. Effect of Sodium Selenate on Hippocampal Proteome of 3×Tg-AD Mice-Exploring the Antioxidant Dogma of Selenium against Alzheimer's Disease.

    Science.gov (United States)

    Iqbal, Javed; Zhang, Kaoyuan; Jin, Na; Zhao, Yuxi; Liu, Qiong; Ni, Jiazuan; Shen, Liming

    2018-04-19

    Selenium (Se), an antioxidant trace element, is an important nutrient for maintaining brain functions and is reported to be involved in Alzheimer's disease (AD) pathologies. The present study has been designed to elucidate the protein changes in hippocampus of 3×Tg-AD mice after supplementing sodium selenate as an inorganic source of selenium. By using iTRAQ proteomics technology, 113 differentially expressed proteins (DEPs) are found in AD/WT mice with 37 upregulated and 76 downregulated proteins. Similarly, in selenate-treated 3×Tg-AD (ADSe/AD) mice, 115 DEPs are found with 98 upregulated and 17 downregulated proteins. The third group of mice (ADSe/WT) showed 75 DEPs with 46 upregulated and 29 downregulated proteins. Among these results, 42 proteins (40 downregulated and 2 upregulated) in the diseased group showed reverse expression when treated with selenate. These DEPs are analyzed with different bioinformatics tools and are found associated with various AD pathologies and pathways. Based on their functions, selenate-reversed proteins are classified as structural proteins, metabolic proteins, calcium regulating proteins, synaptic proteins, signaling proteins, stress related proteins, and transport proteins. Six altered AD associated proteins are successfully validated by Western blot analysis. This study shows that sodium selenate has a profound effect on the hippocampus of the triple transgenic AD mice. This might be established as an effective therapeutic agent after further investigation.

  6. Cistatina C, PCR, Log TG/HDLc e Sindrome Metabolica estao Relacionados a Microalbuminuria na Hipertensao

    Directory of Open Access Journals (Sweden)

    Rafaela do Socorro Souza e Silva Moura

    2014-01-01

    Full Text Available Fundamento: Em pacientes com hipertensão arterial sistêmica, a microalbuminúria é um marcador de lesão endotelial e está associada a um risco aumentado de doença cardiovascular. Objetivo: O objetivo do presente estudo foi determinar os fatores que influenciam a ocorrência de microalbumiúria em pacientes hipertensos com creatinina sérica menor que 1,5 mg/dL. Métodos: Foram incluídos no estudo 133 pacientes brasileiros atendidos em um ambulatório multidisciplinar para hipertensos. Pacientes com creatinina sérica maior do que 1,5 mg/dL e aqueles com diabete mellitus foram excluídos do estudo. A pressão arterial sistólica e diastólica foi aferida. O índice de massa corporal (IMC e a taxa de filtração glomerular estimada pela fórmula CKD-EPI foram calculados. Em um estudo transversal, creatinina, cistatina C, colesterol total, HDL colesterol, LDL colesterol, triglicerídeos, proteína C-reativa (PCR e glicose foram mensurados em amostra de sangue. A microalbuminúria foi determinada na urina colhida em 24 horas. Os hipertensos foram classificados pela presença de um ou mais critérios para síndrome metabólica. Resultados: Em análise de regressão múltipla, os níveis séricos de cistatina C, PCR, o índice aterogênico log TG/HDLc e a presença de três ou mais critérios para síndrome metabólica foram positivamente correlacionados com a microalbuminuria (r2: 0,277; p < 0,05. Conclusão: Cistatina C, PCR, log TG/HDLc e presença de três ou mais critérios para síndrome metabólica, independentemente da creatinina sérica, foram associados com a microalbuminúria, um marcador precoce de lesão renal e de risco cardiovascular em pacientes com hipertensão arterial essencial.

  7. The relationship between the Tg depression and the speeding up of physical aging in polystyrene/gold nanocomposites

    Science.gov (United States)

    Boucher, Virginie M.; Cangialosi, Daniele; Alegria, Angel; Colmenero, Juan

    2011-03-01

    The effect of gold nanoparticles on the segmental dynamics, glass transition (Tg) and physical aging of polystyrene (PS) was studied in PS/Gold nanocomposites samples containing 5 and 15 wt.% of 60 nm spherical gold nanoparticles, surface-treated with thiolated-PS. While the segmental dynamics of PS, as assessed by broadband dielectric spectroscopy (BDS), was found to be unchanged in presence of gold nanoparticles, the calorimetric Tg of PS was shown to decrease with increasing the amount of nanoparticles in the samples. Furthermore, the physical aging of PS, monitored by measuring the enthalpy relaxation below Tg by means of DSC, was shown to speed up with increasing the nanoparticles weight fraction, i.e. the amount of PS/Gold interface in the hybrid material. Thus, the main conclusion of our work is that PS molecular mobility and out-of-equilibrium dynamics are decoupled in these nanocomposites. The significant effect of the amount of PS/Gold interface on both the physical aging rate of PS and the calorimetric Tg depression are quantitatively accounted for by a model based on the diffusion of free volume holes towards polymer interfaces, with a diffusion coefficient depending only on the molecular mobility.

  8. No Effect of Resveratrol on VLDL-TG Kinetics and Insulin Sensitivity in Obese Men with Nonalcoholic Fatty Liver Disease

    DEFF Research Database (Denmark)

    Poulsen, Marianne K; Nellemann, Birgitte; Bibby, Bo Martin

    2018-01-01

    The present study assess long-term effects of high-dose Resveratrol (RSV) on basal and insulin-mediated very low-desity lipoprotein triglyceride (VLDL-TG), palmitate and glucose kinetics, and liver fat content in men with nonalcoholic fatty liver disease (NAFLD). Participants (n=16) were non...

  9. Anxiety-like behavior as an early endophenotype in the TgF344-AD rat model of Alzheimer's disease.

    Science.gov (United States)

    Pentkowski, Nathan S; Berkowitz, Laura E; Thompson, Shannon M; Drake, Emma N; Olguin, Carlos R; Clark, Benjamin J

    2018-01-01

    Alzheimer's disease (AD) is characterized by progressive cognitive decline and the presence of aggregates of amyloid beta (plaques) and hyperphosphorylated tau (tangles). Early diagnosis through neuropsychological testing is difficult due to comorbidity of symptoms between AD and other types of dementia. As a result, there is a need to identify the range of behavioral phenotypes expressed in AD. In the present study, we utilized a transgenic rat (TgF344-AD) model that bears the mutated amyloid precursor protein as well as presenilin-1 genes, resulting in progressive plaque and tangle pathogenesis throughout the cortex. We tested young adult male and female TgF344-AD rats in a spatial memory task in the Morris water maze and for anxiety-like behavior in the elevated plus-maze. Results indicated that regardless of sex, TgF344-AD rats exhibited increased anxiety-like behavior in the elevated plus-maze, which occurred without significant deficits in the spatial memory. Together, these results indicate that enhanced anxiety-like behavior represents an early-stage behavioral marker in the TgF344-AD rat model. Copyright © 2017 Elsevier Inc. All rights reserved.

  10. Molecular structure of virgin and Tg cycled (Ag2Se)x (AsSe)1-x bulk glasses

    Science.gov (United States)

    Wachtman, Jacob; Chen, Ping; Boochand, P.

    2009-03-01

    AsSe, the base glass (x = 0) in the titled ternary, is an interesting example of a chalcogenide that is partially de-mixed into As4Se4 molecules segregated from a connected AsSe network, with the latter determining glass network properties. Raman scattering reveals sharp modes of the Realgar molecules that are superimposed on broad modes coming from of the backbone. Upon Tg cycling virgin samples (as quenched melts), the concentration of de-mixed As4Se4 molecules decreases, suggesting that thermally induced polymerization occurs; molecules break up to form part of the connective tissue. Modulated DSC experiments reveal a broad exotherm near 140 ^oC in virgin samples, which becomes nearly extinct in Tg cycled samples. The exotherm may represent Realgar molecules nano-crystallizing as the temperature approaches Tg. Compositional trends in thermal parameters such as Tg(x), δCp(x), and the δHnr(x) as a function of Ag2Se content `x' of the glasses will be reported.

  11. Citalopram Ameliorates Impairments in Spatial Memory and Synaptic Plasticity in Female 3xTgAD Mice

    Directory of Open Access Journals (Sweden)

    Zhang Wei

    2017-01-01

    Full Text Available Alzheimer’s disease (AD is the primary cause of dementia. There is no effective treatment. Amyloid-β peptide (Aβ plays an important role in the pathogenesis and thus strategies suppressing Aβ production and accumulation seem promising. Citalopram is an antidepressant drug and can decrease Aβ production and amyloid plaques in transgenic mice of AD and humans. Whether citalopram can ameliorate memory deficit was not known yet. We tested the effects of citalopram on behavioral performance and synaptic plasticity in female 3xTgAD mice, a well-characterized model of AD. Mice were treated with citalopram or water from 5 months of age for 3 months. Citalopram treatment at approximately 10 mg/kg/day significantly improved spatial memory in the Morris water maze (MWM test, while not affecting anxiety-like and depression-like behavior in 3xTgAD mice. Further, hippocampal long-term potentiation (LTP impairment in 3xTgAD mice was reversed by citalopram treatment. Citalopram treatment also significantly decreased the levels of insoluble Aβ40 in hippocampal and cortical tissues in 3xTgAD mice, accompanied with a reduced amyloid precursor protein (APP. Together, citalopram treatment may be a promising strategy for AD and further clinical trials should be conducted to verify the effect of citalopram on cognition in patients with AD or mild cognitive impairment.

  12. STUDY ON THE CONTENT OF SEDIMENT PARTICLES IN THE AIR AROUND TG. JIU TOWN

    Directory of Open Access Journals (Sweden)

    Ramona Violeta Cazalbașu

    2016-12-01

    Full Text Available One of the most important problems of the modern era is the air pollution. This phenomenon, highly complex, has become the focus of several international organizations since the consequences of air pollution are felt outside the country borders. By and large wecan speak of a regional pollution, which consists of atmospheric contamination by waste or by products liquids, solids gas, threatening the health of people, plants and animals or which can attack materials, reduce visibility and cause unpleasant odors. On a planetary scale, the elimination or accumulation in the atmosphere of certain products, leads to irreparable consequences on the planet's natural balance: ozone depletion and global warming of the atmosphere. This paper presents the study on the sedimentparticles in the air in Tg-Jiu. Determination of particulate matter from the air was done according to Standard no. 10195 / 75.Air purity.Determination of settled particles. In 2014 no exceeding of the maximum allowable concentration of sediment particles has been found in the four sampling points and in2015, out of a total of 60 measurements in four sampling points only one was above the maximum permissible concentration

  13. High-Tg Polynorbornene-Based Block and Random Copolymers for Butanol Pervaporation Membranes

    Science.gov (United States)

    Register, Richard A.; Kim, Dong-Gyun; Takigawa, Tamami; Kashino, Tomomasa; Burtovyy, Oleksandr; Bell, Andrew

    Vinyl addition polymers of substituted norbornene (NB) monomers possess desirably high glass transition temperatures (Tg); however, until very recently, the lack of an applicable living polymerization chemistry has precluded the synthesis of such polymers with controlled architecture, or copolymers with controlled sequence distribution. We have recently synthesized block and random copolymers of NB monomers bearing hydroxyhexafluoroisopropyl and n-butyl substituents (HFANB and BuNB) via living vinyl addition polymerization with Pd-based catalysts. Both series of polymers were cast into the selective skin layers of thin film composite (TFC) membranes, and these organophilic membranes investigated for the isolation of n-butanol from dilute aqueous solution (model fermentation broth) via pervaporation. The block copolymers show well-defined microphase-separated morphologies, both in bulk and as the selective skin layers on TFC membranes, while the random copolymers are homogeneous. Both block and random vinyl addition copolymers are effective as n-butanol pervaporation membranes, with the block copolymers showing a better flux-selectivity balance. While polyHFANB has much higher permeability and n-butanol selectivity than polyBuNB, incorporating BuNB units into the polymer (in either a block or random sequence) limits the swelling of the polyHFANB and thereby improves the n-butanol pervaporation selectivity.

  14. MO-A-BRB-00: TG191: Clinical Use of Luminescent Dosimeters

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2016-06-15

    This presentation will highlight the upcoming TG-191 report: Clinical Use of Luminescent Dosimeters. Luminescent dosimetry based on TLD and OSLD is a practical, accurate, and precise technique for point dosimetry in medical physics applications. The charges of Task Group 191 were to detail the methodologies for practical and optimal luminescent dosimetry in a clinical setting. This includes (1) To review the variety of TLD/OSL materials available, including features and limitations of each. (2) To outline the optimal steps to achieve accurate and precise dosimetry with luminescent detectors and to evaluate the uncertainty induced when less rigorous procedures are used. (3) To develop consensus guidelines on the optimal use of luminescent dosimeters for clinical practice. (4) To develop guidelines for special medically relevant uses of TLDs/OSLs (e.g., mixed field i.e. photon/neutron dosimetry, particle beam dosimetry, skin dosimetry). While this report provides general guidelines for arbitrary TLD and OSLD processes, the report, and therefore this presentation, provide specific guidance for TLD-100 (LiF:Ti,Mg) and nanoDot (Al2O3:C) dosimeters because of their prevalence in clinical practice. Learning Objectives: Understand the available dosimetry systems, and basic theory of their operation Understand the range of dose determination methodologies and the uncertainties associated with them Become familiar with special considerations for TLD/OSLD relevant for special clinical situations Learn recommended commissioning and QA procedures for these dosimetry systems.

  15. MO-A-BRB-01: TG191: Clinical Use of Luminescent Dosimeters

    Energy Technology Data Exchange (ETDEWEB)

    Kry, S. [UT MD Anderson Cancer Center (United States)

    2016-06-15

    This presentation will highlight the upcoming TG-191 report: Clinical Use of Luminescent Dosimeters. Luminescent dosimetry based on TLD and OSLD is a practical, accurate, and precise technique for point dosimetry in medical physics applications. The charges of Task Group 191 were to detail the methodologies for practical and optimal luminescent dosimetry in a clinical setting. This includes (1) To review the variety of TLD/OSL materials available, including features and limitations of each. (2) To outline the optimal steps to achieve accurate and precise dosimetry with luminescent detectors and to evaluate the uncertainty induced when less rigorous procedures are used. (3) To develop consensus guidelines on the optimal use of luminescent dosimeters for clinical practice. (4) To develop guidelines for special medically relevant uses of TLDs/OSLs (e.g., mixed field i.e. photon/neutron dosimetry, particle beam dosimetry, skin dosimetry). While this report provides general guidelines for arbitrary TLD and OSLD processes, the report, and therefore this presentation, provide specific guidance for TLD-100 (LiF:Ti,Mg) and nanoDot (Al2O3:C) dosimeters because of their prevalence in clinical practice. Learning Objectives: Understand the available dosimetry systems, and basic theory of their operation Understand the range of dose determination methodologies and the uncertainties associated with them Become familiar with special considerations for TLD/OSLD relevant for special clinical situations Learn recommended commissioning and QA procedures for these dosimetry systems.

  16. Studies concerning recycling by composting organic waste in Tg-Mureş

    Directory of Open Access Journals (Sweden)

    Florica Morar

    2011-12-01

    Full Text Available Recycling organic waste has become a matter of utmost importance for overall healthiness of the Earth, its volume largely interacting with the economic development. The problem tends to become a vital matter of survival for an entire society. In this context, recovery, recycling, physical-chemical treatment, composting or incineration are methods of waste processing, commonly used in most countries of the world. These measures are intended to both environmental protection and rational use and economically efficient. Based on the data regarding the municipal waste generated in Mures County, in previous years, and in Tg-Mures city, in 2007 were calculated the quantities expected to generate by the year 2038. Also, concerning the cleaning recovery it is proposed the pile composting method, being, from our point of view, more Beneficial in the area. In conclusion, at county level but at city level too, there is still working to do, primarily in terms of awareness, not only the population but also the relevant, local bodies, of what means the cleaning recovery of the municipal waste.

  17. MO-A-BRB-01: TG191: Clinical Use of Luminescent Dosimeters

    International Nuclear Information System (INIS)

    Kry, S.

    2016-01-01

    This presentation will highlight the upcoming TG-191 report: Clinical Use of Luminescent Dosimeters. Luminescent dosimetry based on TLD and OSLD is a practical, accurate, and precise technique for point dosimetry in medical physics applications. The charges of Task Group 191 were to detail the methodologies for practical and optimal luminescent dosimetry in a clinical setting. This includes (1) To review the variety of TLD/OSL materials available, including features and limitations of each. (2) To outline the optimal steps to achieve accurate and precise dosimetry with luminescent detectors and to evaluate the uncertainty induced when less rigorous procedures are used. (3) To develop consensus guidelines on the optimal use of luminescent dosimeters for clinical practice. (4) To develop guidelines for special medically relevant uses of TLDs/OSLs (e.g., mixed field i.e. photon/neutron dosimetry, particle beam dosimetry, skin dosimetry). While this report provides general guidelines for arbitrary TLD and OSLD processes, the report, and therefore this presentation, provide specific guidance for TLD-100 (LiF:Ti,Mg) and nanoDot (Al2O3:C) dosimeters because of their prevalence in clinical practice. Learning Objectives: Understand the available dosimetry systems, and basic theory of their operation Understand the range of dose determination methodologies and the uncertainties associated with them Become familiar with special considerations for TLD/OSLD relevant for special clinical situations Learn recommended commissioning and QA procedures for these dosimetry systems.

  18. MO-A-BRB-00: TG191: Clinical Use of Luminescent Dosimeters

    International Nuclear Information System (INIS)

    2016-01-01

    This presentation will highlight the upcoming TG-191 report: Clinical Use of Luminescent Dosimeters. Luminescent dosimetry based on TLD and OSLD is a practical, accurate, and precise technique for point dosimetry in medical physics applications. The charges of Task Group 191 were to detail the methodologies for practical and optimal luminescent dosimetry in a clinical setting. This includes (1) To review the variety of TLD/OSL materials available, including features and limitations of each. (2) To outline the optimal steps to achieve accurate and precise dosimetry with luminescent detectors and to evaluate the uncertainty induced when less rigorous procedures are used. (3) To develop consensus guidelines on the optimal use of luminescent dosimeters for clinical practice. (4) To develop guidelines for special medically relevant uses of TLDs/OSLs (e.g., mixed field i.e. photon/neutron dosimetry, particle beam dosimetry, skin dosimetry). While this report provides general guidelines for arbitrary TLD and OSLD processes, the report, and therefore this presentation, provide specific guidance for TLD-100 (LiF:Ti,Mg) and nanoDot (Al2O3:C) dosimeters because of their prevalence in clinical practice. Learning Objectives: Understand the available dosimetry systems, and basic theory of their operation Understand the range of dose determination methodologies and the uncertainties associated with them Become familiar with special considerations for TLD/OSLD relevant for special clinical situations Learn recommended commissioning and QA procedures for these dosimetry systems.

  19. SU-E-T-468: Implementation of the TG-142 QA Process for Seven Linacs with Enhanced Beam Conformance

    Energy Technology Data Exchange (ETDEWEB)

    Woollard, J; Ayan, A; DiCostanzo, D; Grzetic, S; Hessler, J; Gupta, N [OH State University, Columbus, OH (United States)

    2015-06-15

    Purpose: To develop a TG-142 compliant QA process for 7 Varian TrueBeam linear accelerators (linacs) with enhanced beam conformance and dosimetrically matched beam models. To ensure consistent performance of all 7 linacs, the QA process should include a common set of baseline values for use in routine QA on all linacs. Methods: The TG 142 report provides recommended tests, tolerances and frequencies for quality assurance of medical accelerators. Based on the guidance provided in the report, measurement tests were developed to evaluate each of the applicable parameters listed for daily, monthly and annual QA. These tests were then performed on each of our 7 new linacs as they came on line at our institution. Results: The tolerance values specified in TG-142 for each QA test are either absolute tolerances (i.e. ±2mm) or require a comparison to a baseline value. The results of our QA tests were first used to ensure that all 7 linacs were operating within the suggested tolerance values provided in TG −142 for those tests with absolute tolerances and that the performance of the linacs was adequately matched. The QA test results were then used to develop a set of common baseline values for those QA tests that require comparison to a baseline value at routine monthly and annual QA. The procedures and baseline values were incorporated into a spreadsheets for use in monthly and annual QA. Conclusion: We have developed a set of procedures for daily, monthly and annual QA of our linacs that are consistent with the TG-142 report. A common set of baseline values was developed for routine QA tests. The use of this common set of baseline values for comparison at monthly and annual QA will ensure consistent performance of all 7 linacs.

  20. SU-E-T-468: Implementation of the TG-142 QA Process for Seven Linacs with Enhanced Beam Conformance

    International Nuclear Information System (INIS)

    Woollard, J; Ayan, A; DiCostanzo, D; Grzetic, S; Hessler, J; Gupta, N

    2015-01-01

    Purpose: To develop a TG-142 compliant QA process for 7 Varian TrueBeam linear accelerators (linacs) with enhanced beam conformance and dosimetrically matched beam models. To ensure consistent performance of all 7 linacs, the QA process should include a common set of baseline values for use in routine QA on all linacs. Methods: The TG 142 report provides recommended tests, tolerances and frequencies for quality assurance of medical accelerators. Based on the guidance provided in the report, measurement tests were developed to evaluate each of the applicable parameters listed for daily, monthly and annual QA. These tests were then performed on each of our 7 new linacs as they came on line at our institution. Results: The tolerance values specified in TG-142 for each QA test are either absolute tolerances (i.e. ±2mm) or require a comparison to a baseline value. The results of our QA tests were first used to ensure that all 7 linacs were operating within the suggested tolerance values provided in TG −142 for those tests with absolute tolerances and that the performance of the linacs was adequately matched. The QA test results were then used to develop a set of co