Thermogravimetric investigations of vanadium complexes

International Nuclear Information System (INIS)

Bechmann, W.; Uhlemann, E.; Ludwig, W.

1987-01-01

Extensive studies on oxovanadium(IV) and (V) complexes with bidentate chelating ligands include thermogravimetric investigations. TG, DTG, and DTA data provide additional facts to redox behaviour and stability of the complexes. These data also allow a critical appreciation of the given melting temperatures. (author)

Pb-H2O Thermogravimetric Plants. The Rankine Cycle

International Nuclear Information System (INIS)

Arosio, S.; Carlevaro, R.

2000-01-01

An economic evaluation concerning Pb-H 2 O thermogravimetric systems with an electric power in the range 200-1.000 kW has been done. Moreover, plant and running costs for a thermogravimetric and a Rankine cycle, 1 MW power, have been compared. Basically due to the lead charge, the plant cost of the former is higher: nevertheless such amount can be recuperated in less than three years, being higher the running cost of the latter [it

Thermogravimetric analysis and dissociation pressure of caesium trihalides

International Nuclear Information System (INIS)

Harris, G.S.; McKechnie, J.S.

1982-01-01

We have carried out a thermogravimetric study of caesium trihalides to obtain, from the procedural decomposition temperatures, an order of apparent thermal stability which could be compared with the order of thermodynamic stability obtained from vapour pressure measurements. Thermogravimetric analysis could also prove to be a useful method for rapid analysis of metal polyhalides. The thermograms indicated a one-step decomposition for each compound; the procedural decomposition temperatures and percentage weight losses obtained are given. Dissociation pressures were measured and values of equilibrium constant and enthalpy of dissociation were calculated. The results are given. The 'stability' order obtained is discussed. (U.K.)

Thermogravimetric-quadrupole mass-spectrometric analysis of geochemical samples.

Science.gov (United States)

Gibson, E. K., Jr.; Johnson, S. M.

1972-01-01

Thermogravimetric-quadrupole mass-spectrometric-analysis techniques can be used to study a wide variety of problems involving decomposition processes and identification of released volatile components. A recording vacuum thermoanalyzer has been coupled with a quadrupole mass spectrometer. The rapid scan capabilities of the quadrupole mass spectrometer are used to identify the gaseous components released. The capability of the thermogravimetric-quadrupole mass spectrometer to provide analytical data for identification of the released volatile components, for determination of their sequence of release and for correlation of thermal-decomposition studies is illustrated by an analysis of the Orgueil carbonaceous chondrite.

THERMOGRAVIMETRIC INVESTIGATIONS OF VAGINAL SUPPOSITORY WITH THYME OIL

Directory of Open Access Journals (Sweden)

N. V. Melnikova

2015-04-01

Full Text Available One of the main stages in new medicines creation is the development of their making technology. Technological process of suppository making includes ratherlongthermal treatment during preparation and homogenization of suppository base, active substancesaddition. These factors create danger of chemical and physical transformation of active substances and excipients in suppository up to their destruction and change of pharmacological and physical-chemical properties. Use of thermogravimetric analysis in pharmaceutical technology allows to studythepossibility of chemical interaction in dosage forms over the wide temperature range. The aim of this work is study of thermal treatmenteffects of suppository base with thyme oil over the temperature range of suppository manufacturing. Methods and results. As an object of thermogravimetric study vaginal suppository with thyme oil 0,2 g, suppository-placebo containing propylenglycol, polyethylene glycol 400, proxanol 268, twin 80 and the active ingredient of «Царствоароматов», Ukraine, production were used. Thermogravimetric analysis was carried out on the derivatograph«Shimadzu DTG-60», Japan, with the platinum and platinum-rhodiumthermopair with samples heating in aluminiumcrucibles from 25 to 200ºС. As standard α-Al2O3was used.Heating rate was 10ºСper min.Mass of the samples was 23,45– 39,63 mg. Obtained data were registered by the derivatograph as curves T, DTA, TGA. The T curve on the derivatogramm shows the temperature change and the TGA curve demonstrates the sample mass change during investigation. The DTA curve reflects differentiation of thermal effects and contains information about endothermic and exothermal maximum and is used for qualitative valuation of derivatogramm. According to results of thermogravimetric investigation the thyme oil is thermostable substance which is gradually evaporating during heating. So, at the beginning of study the test sample mass was 23

Thermogravimetric analysis and thermal degradation behaviour of advanced PMR-X carbon fiber composites

International Nuclear Information System (INIS)

Rngie, M.

2003-01-01

Thermal degradation behavior of sized and unsized carbon fibers in polyimide matrix was investigated. Degradation of neat resin and unidirectional laminates were investigated by thermogravimetric analysis technique at temperatures between 470 d ig C -650 d ig C and up to 250 h rs. Isothermal ageing of the PMR-X composite samples under different test conditions (i. e. different temperatures and prolonged aging times), showed that oxidation and degradation occurs in stage three different rates. Thermogravimetric analysis showed that the cured PMR-X composite panels are more stable in an inert atmosphere (nitrogen atmosphere)than in air and the degradation of neat resin is much higher than the composite samples. However, the rate of degradation of the unsized untreated carbon fibers in nitrogen environment is much higher than that for the PMR-X composites containing sized fibers

Thermogravimetric analysis of the polymer acrylate-vinyl ether mixture cured by radiation

International Nuclear Information System (INIS)

Danu, Sugiarto

1998-01-01

An experiment on thermal stability of the polymer acrylate-vinyl ether mixture cured by radiation have been done using thermogravimetric analysis. Three kinds of acrylic oligomers i.e., epoxy acrylate, urethane acrylate, and polypropylene glycol diacrylate, and vinyl ether monomers i.e., triethylene glycol divinyl ether (DVE-3), 1,4-cyclohexane dimethanol divinyl ether (CHVE), and butanediol monovinyl ether (HBVE) were used in the experiment. Reaction was taken via radical and cationic polymerisation. In case of cationic polymerisation, diphenyliodonium hexafluorophosphate fotoinisiator was used in the formulation. Thermogravimetric analysis was conducted in a nitrogen atmosphere at a flow rate of 40 ml/minute with a constant heating rate 10 o C and evaluation range were done from 25 to 500 o C. The results of thermogravimetric analysis showed that acrylate and DVE-3 mixture produced the polymer films with higher thermal stability than the mixture of acrylate with CHVE or HBVE. The composition of acrylate-vinyl ether mixture and degree of unsaturation of vinyl ether monomers influenced the thermal stability of polymer. The mixture of epoxy acrylate-vinyl ether and polypropylene glycol diacrylate-vinyl ether have 1 initial decomposition temperature whereas the urethane acrylate-vinyl ether mixture has 2 initial decomposition temperatures. (authors)

Thermogravimetric and kinetic study of methylolmelamine ...

African Journals Online (AJOL)

Some salient properties of cotton cellulose which requires it to be treated with additives to improve its versatility were examined taken into consideration, the molecular structure. Thermogravimetric analysis of the cotton fabric and the treated cotton fabric were carried out in an improvised muffled furnace. The result was in ...

Thermogravimetric-Mass Spectrometric Study of the Pyrolysis Behavior of PVC

Institute of Scientific and Technical Information of China (English)

SUN Qing-lei; SHI Xin-gang; LIN Yun-liang; ZHU He; WANG Xiao; CHENG Chuan-ge; LIU Jian-hua

2007-01-01

The pyrolysis characteristics of PVC were systematically investigated using a Netzschne TG thermo-balance coupled to a quadrupole mass spectrometer. The pyrolysis conditions were 0.1 MPa of Ar, a heating rate of 10 ℃/min and a final temperature of 1000 ℃. Both the thermogravimetric properties and the simultaneous evolution of gaseous products during pyrolysis were studied. The TG/DTG results showed that as the pyrolysis temperature increases the weight loss and weight loss rate of PVC increases. Near 412 ℃ the weight loss rate attained its peak value. At higher temperatures the rate of loss gradually decreases. The gases evolved during thermogravimetric analysis were analyzed by a mass spectrometer, monitoring the relative intensity of HCl, C6H6, light hydrocarbon and chlorine-containing gases. The evolution curves showed that HCl, C6H6, light hydrocarbon and chlorine-containing gases all peak at about 416 ℃. This is consistent with the fact that the weight loss curves also peak at about 412 ℃. The extensive HCl evolution is consistent with the high chlorine content of PVC. The formation of these gases can be explained by considering these reactions: dehydrochlorination, intramolecular cyclization and the addition of HCl to unsaturated hydrocarbons.

Spectroscopic and thermogravimetric study of nickel sulfaquinoxaline complex

International Nuclear Information System (INIS)

Tailor, Sanjay M.; Patel, Urmila H.

2016-01-01

The ability of sulfaquinoxaline (4-Amino-N-2-quinoxalinylbenzenesulfonamide) to form metal complexes are investigated. The nickel complex of sulfaquinoxaline is prepared by reflux method and characterized by CHN analysis and IR spectra. The results of IR spectral data suggest that the binding of nickel atom to the sulfonamidic nitrogen are in good agreement. The thermogravimetric analysis (TGA), differential thermal analysis (DTA) and differential thermogravimetric (DTG) analysis of nickel sulfaquinoxaline are carried out from ambient temperature to 750°C in inert nitrogen atmosphere. The activation energy, enthalpy, entropy and Gibbs free energy of nickel sulfaquinoxaline complex is determined from the thermal curves using Broido method. The results are reported in this paper.

Thermogravimetric analysis of forest understory grasses

Science.gov (United States)

Thomas Elder; John S. Kush; Sharon M. Hermann

2011-01-01

Forest understory grasses are of significance in the initiation, establishment and maintenance of fire, whether used as a management tool or when occurring as wildfire. The fundamental thermal properties of such grasses are critical to their behavior in fire situations and have been investigated in the current work by the application of thermogravimetric analysis (TGA...

Thermal decomposition characteristics of microwave liquefied rape straw residues using thermogravimetric analysis

Science.gov (United States)

Xingyan Huang; Cornelis F. De Hoop; Jiulong Xie; Chung-Yun Hse; Jinqiu Qi; Yuzhu Chen; Feng Li

2017-01-01

The thermal decomposition characteristics of microwave liquefied rape straw residues with respect to liquefaction condition and pyrolysis conversion were investigated using a thermogravimetric (TG) analyzer at the heating rates of 5, 20, 50 °C min-1. The hemicellulose decomposition peak was absent at the derivative thermogravimetric analysis (DTG...

Thermogravimetric studies on the silicothermic reduction of uranium tetrafluoride under nitrogen

International Nuclear Information System (INIS)

Venkataramani, R.; Bhatt, Y.J.; Krishnamurthy, N.; Garg, S.P.

1986-01-01

This paper presents details of the experimental procedure and results obtained by thermogravimetric studies on the preparation of uranium nitrides by silicothermic reduction of uranium tetrafluoride under a nitrogen atmosphere. The folowing sequential steps are involved during the reaction: 4UF 4 +Si->4UF 3 +SiF 4 (g), 2UF 3 +Si+N 2 ->2UNF+SiF 4 (g), 4UNF+Si+N 2 ->2U 2 N 3 +SiF 4 (g), the uranium sesquintride U 2 N 3 obtained in the above process then decomposed at 1370 K under a dynamic vacuum of less than 10 -2 Tor to yield uranium mononitride of purity better than 99.9%, according to reaction 2U 2 N 3 ->4UN+N 2 (g). The chemical composition of the intermediate products formed during the sequential steps of the process, assessed by thermogravimetric and differential thermogravimetric studies, were further confirmed by chemical and X-ray analysis

Thermogravimetric investigations of cream with minoxidil

Directory of Open Access Journals (Sweden)

I. V. Gnitko

2016-12-01

Full Text Available Minoxidil is one of the most effective and modern medications, which is used in modern trichology for hair growth stimulation in case of androgenic and other forms of alopecia. Clinical effect of this substance is caused by the intensification of metabolic processes in the skin due to intensification of microcirculation. For local application domestic dermatology uses imported minoxidil medicines in form of alcohol-water lotions and aerosols. The use of semisolid dosage form with minoxidil for external administration will allow to increase its efficacy and will widen the arsenal of domestic pharmacotherapeutic agents for hair growth stimulation. Rational composition of minoxidil semisolid dosage form for external use with 2% of active substance has been developed at the Department of Medicinal Preparations Technology, Zaporozhye State Medical University as a result of complex physical-chemical, microbiological and biopharmaceutical investigations. The aim of this work is the study of thermal treatment effects of cream-mask with minoxidil for external use over the temperature range, which is used in technological process of this dosage form manufacturing. Materials and methods. Cream with 2% of minoxidil on the emulsion base and its excipients have been used as the object for the thermogravimetric investigations. Thermogravimetric analysis has been carried out on the derivatograph «Shimadzu DTG-60», Japan, with the platinum and platinum-rhodium thermopair with samples’ heating in aluminium crucibles from 25 to 200ºС. Results. According to thermogravimetric experimental data minoxidil is a thermal stable substance from 26 to 240ºС. During experimental process insignificant endothermic effect was determined at 191,72ºС. However the mass of the example to the end of experiment practically didn’t change (decrease on 0,32%. Thermal effects on the derivatogram of minoxidil emulsion cream match with thermal effects of the base components and

Characterization of microalga Chlorella as a fuel and its thermogravimetric behavior

International Nuclear Information System (INIS)

Rizzo, Andrea Maria; Prussi, Matteo; Bettucci, Lorenzo; Libelli, Ilaria Marsili; Chiaramonti, David

2013-01-01

Highlights: ► Proximate and ultimate analysis of two microalgae (Nannochloropsis and Chlorella spp.). ► TGA of Chlorella spp. and Nannochloropsis investigated at 15 °C/min up to 800 °C. ► 1.2 kg of Chlorella pyrolyzed in a novel batch, intermediate pyrolysis pilot reactor at 450 °C. ► Bio-oil from Chlorella oil analysed and compared to pine chips fast pyrolysis oil. ► Bio-oil from Chlorella exhibited superior properties compared to lignocellulosic pyrolysis oil as intermediate energy carrier. -- Abstract: Microalgae are photosynthetic microorganisms living in marine or freshwater environment. In this study, samples of Chlorella spp. and Nannochloropsis from two different origins were analysed to settle a preliminary characterization of these microorganisms as intermediate energy carriers and their properties compared to a conventional lignocellulosic feedstock (pine chips). Both microalgae samples were characterized in terms of elemental composition (CHONS and P) and thermogravimetric behavior. This was investigated through non-isothermal thermogravimetric analysis in nitrogen atmosphere at heating rate of 15 °C min −1 and temperature up to 800 °C. Solid residues produced at 300 °C and 800 °C from TGA were also analysed to determine the ultimate composition of chars. Activation energy, reaction order and pre-exponential factor were calculated for the single step conversion mechanism of 1 g of Chlorella spp. and compared to literature data on Chlorella protothecoides and Spirulina platensis. Calculated kinetic parameters, given as intervals of several determinations, resulted to be: pre-exponential factor (A) 1.47–1.62E6 min −1 , activation energy (E) 7.13–7.92E4 J mol −1 , reaction order (n) 1.69–2.41. 1.2 kg of Chlorella spp. was then processed in a newly designed batch pyrolysis pilot reactor, capable of converting up to 1.5 kg h −1 of material, and pyrolysis liquid collected, analysed and compared with a sample of fast pyrolysis

Isothermal thermogravimetric data acquisition analysis system

Science.gov (United States)

Cooper, Kenneth, Jr.

1991-01-01

The description of an Isothermal Thermogravimetric Analysis (TGA) Data Acquisition System is presented. The system consists of software and hardware to perform a wide variety of TGA experiments. The software is written in ANSI C using Borland's Turbo C++. The hardware consists of a 486/25 MHz machine with a Capital Equipment Corp. IEEE488 interface card. The interface is to a Hewlett Packard 3497A data acquisition system using two analog input cards and a digital actuator card. The system provides for 16 TGA rigs with weight and temperature measurements from each rig. Data collection is conducted in three phases. Acquisition is done at a rapid rate during initial startup, at a slower rate during extended data collection periods, and finally at a fast rate during shutdown. Parameters controlling the rate and duration of each phase are user programmable. Furnace control (raising and lowering) is also programmable. Provision is made for automatic restart in the event of power failure or other abnormal terminations. Initial trial runs were conducted to show system stability.

Thermogravimetric analysis and kinetic study of formation of lithium titanate by solid state route

International Nuclear Information System (INIS)

Sonak, Sagar; Jain, Uttam; Sahu, Ashok Kumar; Kumar, Sanjay; Krishnamurthy, Nagaiyar

2015-01-01

The kinetics of formation of lithium titanate from the solid state reaction of lithium carbonate and titanium oxide was studied using non-isothermal thermogravimetric technique. Thermogravimetric data for the reaction of lithium carbonate and titanium oxide was obtained at various heating rates. The methods such as Flynn–Wall–Ozawa and Kissinger–Akahira–Sunose were used to estimate the kinetic parameters from the obtained thermogravimetric data. The average activation energy for the formation of lithium titanate by solid state route was found to be 243 kJ/mol K. The reaction mechanism was determined by the method given by Malek. It was found that the three dimensional diffusion model best describes the reaction kinetics. A kinetic equation describing the reaction is proposed and reaction mechanism is discussed

Hydrogen Adsorption in Zeolite Studied with Sievert and Thermogravimetric Methods

International Nuclear Information System (INIS)

Lesnicenoks, P; Sivars, A; Grinberga, L; Kleperis, J

2012-01-01

Natural clinoptilolite (mixture from clinoptilolite, quartz and muscovite) is activated with palladium and tested for hydrogen adsorption capability at temperatures RT - 200°C. Thermogravimetric and volumetric methods showed that zeolite activated with palladium (1.25%wt) shows markedly high hydrogen adsorption capacity - up to 3 wt%. Lower amount of adsorbed hydrogen (∼1.5 wt%) was found for raw zeolite and activated with higher amount of palladium sample. Hypothesis is proposed that the heating of zeolite in argon atmosphere forms and activates the pore structure in zeolite material, where hydrogen encapsulation (trapping) is believed to occur when cooling down to room temperature. An effect of catalyst (Pd) on hydrogen sorption capability is explained by spillover phenomena were less-porous fractions of natural clinoptilolite sample (quartz and muscovite) are involved.

Thermogravimetric analysis of the gasification of microalgae Chlorella vulgaris.

Science.gov (United States)

Figueira, Camila Emilia; Moreira, Paulo Firmino; Giudici, Reinaldo

2015-12-01

The gasification of microalgae Chlorella vulgaris under an atmosphere of argon and water vapor was investigated by thermogravimetric analysis. The data were interpreted by using conventional isoconversional methods and also by the independent parallel reaction (IPR) model, in which the degradation is considered to happen individually to each pseudo-component of biomass (lipid, carbohydrate and protein). The IPR model allows obtaining the kinetic parameters of the degradation reaction of each component. Three main stages were observed during the gasification process and the differential thermogravimetric curve was satisfactorily fitted by the IPR model considering three pseudocomponents. The comparison of the activation energy values obtained by the methods and those found in the literature for other microalgae was satisfactory. Quantification of reaction products was performed using online gas chromatography. The major products detected were H2, CO and CH4, indicating the potential for producing fuel gas and syngas from microalgae. Copyright © 2015 Elsevier Ltd. All rights reserved.

Thermogravimetric Analysis of Single-Wall Carbon Nanotubes

Science.gov (United States)

Arepalli, Sivram; Nikolaev, Pavel; Gorelik, Olga

2010-01-01

An improved protocol for thermogravimetric analysis (TGA) of samples of single-wall carbon nanotube (SWCNT) material has been developed to increase the degree of consistency among results so that meaningful comparisons can be made among different samples. This improved TGA protocol is suitable for incorporation into the protocol for characterization of carbon nanotube material. In most cases, TGA of carbon nanotube materials is performed in gas mixtures that contain oxygen at various concentrations. The improved protocol is summarized.

Thermogravimetric analysis of silicon carbide-silicon nitride fibers at ambient to 1000 C in air

Science.gov (United States)

Daniels, J. G.; Ledbetter, F. E., III; Clemons, J. M.; Penn, B. G.

1984-01-01

Thermogravimetric analysis of silicon carbide-silicon nitride fibers was carried out at ambient to 1000 C in air. The weight loss over this temperature range was negligible. In addition, the oxidative stability at high temperature for a short period of time was determined. Fibers heated at 1000 C in air for fifteen minutes showed negligible weight loss (i.e., less than 1 percent).

Thermogravimetric studies of vapour-aerosol interactions

International Nuclear Information System (INIS)

Henshaw, J.; Newland, M.S.; Wood, S.J.

1991-01-01

Thermogravimetric analysis has been used to study the interaction of iodine vapour with cadmium, silver and manganese monoxide substrates. These studies have demonstrated the importance of time-dependence data on reaction rates. Iodine did not react with manganese monoxide (as expected from thermodynamic considerations); however, extensive reaction did occur with silver and cadmium. Two rate limiting mechanisms were observed: mass transfer of iodine molecules from the gas phase (leading to linear reaction rates) and parabolic kinetics (ie inversely proportional to the extent of reaction) when the rate was limited by a diffusion process through the reaction product. (author)

Purity Evaluation of Single-Walled Carbon Nanotubes Using Thermogravimetric Analysis

International Nuclear Information System (INIS)

Goak, Jeung Choon; Kim, Tae Yang; Jung, Jongwan; Seo, Young-Soo; Lee, Naesung; Sok, Junghyun

2013-01-01

This study evaluated the purity of single-walled carbon nanotubes (SWCNTs) in the arc-synthesized SWCNT samples by using thermogravimetric analysis (TGA). The as-produced SWCNT samples were heat-treated in air for 20 h at 275-475°C and characterized by scanning and transmission electron microscopes and TGA to establish oxidation temperature ranges of SWCNTs and carbonaceous impurities comprising the samples. Based on these oxidation temperature ranges, derivative thermogravimetric curves were deconvoluted, and differentiated peaks were assigned to SWCNTs and carbonaceous impurities. The compositions and the SWCNT purities of the samples were obtained simply by calculating the areal ratios under the deconvoluted curves. TGA studies on purity evaluation and thermal stabilities of SWCNTs and carbonaceous impurities are likely to provide us with a simple route of thermal oxidation purification to acquire high-purity SWCNT samples.

Nickel hydroxide electrode. 3: Thermogravimetric investigations of nickel (II) hydroxides

Science.gov (United States)

Dennstedt, W.; Loeser, W.

1982-01-01

Water contained in Ni hydroxide influences its electrochemical reactivity. The water content of alpha and beta Ni hydroxides is different with respect to the amount and bond strength. Thermogravimetric experiments show that the water of the beta Ni hydroxides exceeding the stoichiometric composition is completely removed at 160 deg. The water contained in the interlayers of the beta hydroxide, however, is removed only at higher temperatures, together with the water originating from the decomposition of the hydroxide. These differences are attributed to the formation of II bonds within the interlayers and between interlayers and adjacent main layers. An attempt is made to explain the relations between water content and the oxidizability of the Ni hydroxides.

Computer calculations of activation energy for pyrolysis from thermogravimetric curves

International Nuclear Information System (INIS)

Hussain, R.

1994-01-01

A BASIC programme to determine energy of activation for the degradation of polymers has been described. The calculations are based on the results of thermogravimetric curves. This method is applicable for those polymers which produce volatile products upon thermal degradation. (author)

Study and Thermogravimetric analysis of Poly N-4 Aminostyrol

International Nuclear Information System (INIS)

Meghezzi, A.; Lakhdar, Y.; Saidi, M.; Dadamoussa, B.

2006-01-01

The polyaminostyrol samples (PAS) and their copolymers with the styrol differing in position and quantity of amino-group, were obtained by polymerization of monomers on cyclogexan solution. The observed thermal effects were analyzed by the differential thermal analysis combined with a thermogravimetric analysis. It was found that the introduction of amino-groups into the polystyrols increased the temperature of total degradation of polymer from 150 till 260C. The increase in thermostability may be explained by the cohesion of macromolecules with the participation of amino-groups, which results in ammonium evolution, as well as in the decrease of valence area band of -NH2 grouping the region 3370-34440 cm. It was showed that the degree of cohesion formation and thermolysis rate depended on amino-group and their position into the cycle of benzene. (author)

Heater-Integrated Cantilevers for Nano-Samples Thermogravimetric Analysis

OpenAIRE

Toffoli, Valeria; Carrato, Sergio; Lee, Dongkyu; Jeon, Sangmin; Lazzarino, Marco

2013-01-01

The design and characteristics of a micro-system for thermogravimetric analysis (TGA) in which heater, temperature sensor and mass sensor are integrated into a single device are presented. The system consists of a suspended cantilever that incorporates a microfabricated resistor, used as both heater and thermometer. A three-dimensional finite element analysis was used to define the structure parameters. TGA sensors were fabricated by standard microlithographic techniques and tested using mill...

Thermogravimetric evaluation of the suitability of precursors for MOCVD

International Nuclear Information System (INIS)

Kunte, G V; Shivashankar, S A; Umarji, A M

2008-01-01

A method based on the Langmuir equation for the estimation of vapour pressure and enthalpy of sublimation of subliming compounds is described. The variable temperature thermogravimetric/differential thermogravimetric (TG/DTG) curve of benzoic acid is used to arrive at the instrument parameters. Employing these parameters, the vapour pressure–temperature curves are derived for salicylic acid and camphor from their TG/DTG curves. The values match well with vapour pressure data in the literature, obtained by effusion methods. By employing the Clausius–Clapeyron equation, the enthalpy of sublimation could be calculated. Extending the method further, two precursors for metal-organic chemical vapour deposition (MOCVD) of titanium oxide bis-isopropyl bis tert-butyl 2-oxobutanoato titanium, Ti(O i Pr) 2 (tbob) 2 , and bis-oxo-bis-tertbutyl 2-oxobutanoato titanium, [TiO(tbob) 2 ] 2 , have been evaluated. The complex Ti(O i Pr) 2 (tbob) 2 is found to be a more suitable precursor. This approach can be helpful in quickly screening for the suitability of a compound as a CVD precursor

Thermogravimetric analysis and fast pyrolysis of Milkweed.

Science.gov (United States)

Kim, Seung-Soo; Agblevor, Foster A

2014-10-01

Pyrolysis of Milkweed was carried out in a thermogravimetric analyzer and a bubbling fluidized bed reactor. Total liquid yield of Milkweed pyrolysis was between 40.74% and 44.19 wt% between 425 °C and 550 °C. The gas yield increased from 27.90 wt% to 33.33 wt% with increasing reaction temperature. The higher heating values (HHV) of the Milkweed bio-oil were relatively high (30.33-32.87 MJ/kg) and varied with reaction temperature, feeding rate and fluidization velocity. The selectivity for CO2 was highest within non-condensable gases, and the molar ratio of CO2/CO was about 3 at the different reaction conditions. The (13)C NMR analysis, of the bio-oil showed that the relative concentration carboxylic group and its derivatives was higher at 425 °C than 475 °C, which resulted in slightly higher oxygen content in bio-oil. The pH of aqueous phase obtained at 475 °C was 7.37 which is the highest reported for any lignocellulosic biomass pyrolysis oils. Copyright © 2014 Elsevier Ltd. All rights reserved.

Thermogravimetric analysis coupled with chemometrics as a powerful predictive tool for ß-thalassemia screening.

Science.gov (United States)

Risoluti, Roberta; Materazzi, Stefano; Sorrentino, Francesco; Maffei, Laura; Caprari, Patrizia

2016-10-01

β-Thalassemia is a hemoglobin genetic disorder characterized by the absence or reduced β-globin chain synthesis, one of the constituents of the adult hemoglobin tetramer. In this study the possibility of using thermogravimetric analysis (TGA) followed by chemometrics as a new approach for β-thalassemia detection is proposed. Blood samples from patients with β-thalassemia were analyzed by the TG7 thermobalance and the resulting curves were compared to those typical of healthy individuals. Principal Component Analysis (PCA) was used to evaluate the correlation between the hematological parameters and the thermogravimetric results. The thermogravimetric profiles of blood samples from β-thalassemia patients were clearly distinct from those of healthy individuals as result of the different quantities of water content and corpuscular fraction. The hematological overview showed significant decreases in the values of red blood cell indices and an increase in red cell distribution width value in thalassemia subjects when compared with those of healthy subjects. The implementation of a predictive model based on Partial Least Square Discriminant Analysis (PLS-DA) for β-thalassemia diagnosis, was performed and validated. This model permitted the discrimination of anemic patients and healthy individuals and was able to detect thalassemia in clinically heterogeneous patients as in the presence of δβ-thalassemia and β-thalassemia combined with Hb Lepore. TGA and Chemometrics are capable of predicting ß-thalassemia syndromes using only a few microliters of blood without any pretreatment and with an hour of analysis time. A fast, rapid and cost-effective diagnostic tool for the β-thalassemia screening is proposed. Copyright © 2016 Elsevier B.V. All rights reserved.

Thermogravimetric study of γ-irradiated lanthanum oxalate

International Nuclear Information System (INIS)

Nayak, H.; Bhatta, D.

2000-01-01

Thermogravimetric study of La 2 (C 2 O 4 ) 3 , exposed to different doses (5.0 - 50.0 x 10 -2 MGy) of γ-rays has been carried out. Marginal effect is observed at lower doses which is prominent at higher dose (5.0 x 10 -1 MGy). The radiolytic damaged entities, generated by irradiation favours the reaction by creating new potential nucleation centres in the lattice. The solid product, La 2 O 3 formed by irradiation also acts as a heterogeneous catalyst and brings out changes in the reactivity of the solid. (author)

Miniature quartz crystal-resonator-based thermogravimetric detector.

Science.gov (United States)

Sai, N; Tagawa, Y; Sohgawa, M; Abe, T

2014-09-01

In this work, a new design for a microheater combined with a quartz crystal microbalance (QCM) array for thermogravimetric analysis is presented. Each QCM consists of two electrodes to excite thickness-shear-mode vibrations and one microheater to increase the temperature on the crystal backside. In addition, all the electrode pads are patterned on the crystal backside, making the design of the QCM compact and user-friendly. Finally, the proposed QCM array was employed to separate ethanol from methanol. This was successfully achieved via thermal desorption spectra calculated by differentiating the frequency changes.

Thermogravimetric analytical procedures for determining reactivities of chars from New Zealand coals

Energy Technology Data Exchange (ETDEWEB)

Shaw, K.J.; Beamish, B.B.; Rodgers, K.A. [University of Auckland, Auckland (New Zealand). Dept. of Geology

1997-10-22

This paper describes how tightly constrained thermogravimetric experimental procedures (particle size {lt} 212 {mu}m, sample mass 15.5 mg, CO{sub 2} reactant gas, near isothermal conditions) allow the reactivity of chars from high volatile New Zealand coals to be determined to a repeatability of {+-}0.07 h{sup -1} at 900{degree}C and {+-}0.5 h{sup -1} at 1100{degree}C. The procedure also provides proximate analyses information and affords a quick ({lt} 90 min) comparison between different coal types as well as indicating likely operating conditions and problems associated with a particular coal or blend. A clear difference is evident between reactivities of differing New Zealand coal ranks. Between 900 and 1100{degree}C, bituminous coals increase thirtyfold in reactivity compared with fourfold for subbituminous, with the latter being three to five times greater in reactivity at higher temperature.

Thermogravimetric control of intermediate compounds in uranium metallurgy

International Nuclear Information System (INIS)

Gasco Sanchez, L.; Fernandez Cellini, R.

1959-01-01

The thermal decomposition of some intermediate compounds in the metallurgy of the uranium as uranium peroxide, ammonium uranate, uranium and ammonium penta-fluoride, uranium tetrafluoride and uranous oxide has been study by means of the Chevenard's thermo balance. Some data on pyrolysis of synthetic mixtures of intermediate compounds which may occasionally appear during the industrial process, are given. Thermogravimetric methods of control are suggested, usable in interesting products in the uranium metallurgy. (Author) 20 refs

Thermogravimetric analysis of reactor-neutrons-irradiated LEXAN polycarbonate film

International Nuclear Information System (INIS)

Kalsi, P.C.

2000-01-01

The effects of reactor-neutrons irradiation on the thermogravimetric (TG) analysis of LEXAN polycarbonate film in air were studied. Irradiation enhances the degradation rate and the effect increases further with increasing neutron fluence. The kinetics of the different steps of degradation were also evaluated from the TG curves. The activation energy values calculated for all the degradation stages decrease on irradiation. (author)

The degree of hydration assessment of blended cement pastes by differential thermal and thermogravimetric analysis. Morphological evolution of the solid phases

International Nuclear Information System (INIS)

Monteagudo, S.M.; Moragues, A.; Gálvez, J.C.; Casati, M.J.; Reyes, E.

2014-01-01

Highlights: • A proposal of hydration degree calculation for blended cement pastes is presented. • The method is based both on the contributions of various authors and on DTA–TG results. • Paste and mortar specimens with BFS, FA and SF mineral admixtures were used. • The evaluation of CH gives information on hydration and pozzolanic reactions. • The assessment of α provides an insight into future strength evolution. - Abstract: The degree of hydration assessment of cement paste from differential thermal and thermogravimetric analysis data has been performed by several authors that have offered a number of proposals for technical application to blended cements. In this paper, two calculation methods are studied in detail. Then, a proposal of the degree of hydration calculation for blended cements, based on the analysis of experimental results of DTA–TG, is presented. The proposed method combines the contributions of the authors and allows straightforward calculation of the degree of hydration from the experimental results. Validation of the methodology was performed by macroscopic and microstructural tests through paste and mortar specimens with blast furnace slag, flying ash and silica fume mineral admixtures bei(g)ng used. Tests of scanning electron microscopy with an energy dispersive analyser on paste specimens, and of mechanical strength on mortar specimens with the same percentages of substitution, were performed. They showed good agreement with the information derived from the differential thermal and thermogravimetric analysis data

Determination of effective moisture diffusivity and drying kinetics for poplar sawdust by thermogravimetric analysis under isothermal condition.

Science.gov (United States)

Chen, Dengyu; Zheng, Yan; Zhu, Xifeng

2012-03-01

The current study presents a thermogravimetric method to determine the effective moisture diffusivity and drying kinetics of biomass. Drying experiments on poplar sawdust were performed at four temperatures (60, 70, 80, and 90°C) by a thermogravimetric analyzer (TGA). The major assumption in experimentally determining effective diffusivity by Fick's diffusion equation is that drying is mass transfer limited and temperature remains isothermal during drying. The results indicated that TGA could well achieve these determining conditions. The drying process of sawdust mostly took place in the falling rate period. Midilli-Kucuk model showed the best fit for all experimental data. The effective diffusivity values changed from 9.38 × 10(-10)m(2)/s to 1.38 × 10(-9)m(2)/s within the given temperature range, and the activation energy was calculated to be 12.3 kJ/mol. Copyright © 2011 Elsevier Ltd. All rights reserved.

Thermogravimetric study of the reaction of uranium oxides with fluorine

International Nuclear Information System (INIS)

Komura, Motohiro; Sato, Nobuaki; Kirishima, Akira; Tochiyama, Osamu

2008-01-01

Thermogravimetric study of the reaction of uranium oxides with fluorine was conducted by TG-DTA method using anti-corrosion type differential thermobalance. When UO 2 was heated from R.T. to 500 deg. C in 5% F 2 /He atmosphere, the weight increase appeared at ca. 250 deg. C with an exothermic peak. Then the weight decreased slightly with a small exothermic peak followed by the complete volatilization with a large exothermic peak at ca. 350 deg. C. At a flow rate of 15, 30, 60 ml min -1 , there seemed to be no significant change for the fluorination of UO 2 . With the different heating rates of 1, 2, 5 and 10 deg. C min -1 , the fluorination peak shifted to higher temperature with increasing heating rates. For the comparison with thermogravimetric results, phase analysis by XRD method was conducted for the products obtained at different temperatures. At 260 deg. C, the product was UO 2 with a small amount of the intermediate compound, UO 2 F. The amount of this compound increased with increasing temperature up to 320 deg. C. Then another phase of UO 2 F 2 appeared at 340 deg. C but it was immediately fluorinated to the volatile fluoride. When U 3 O 8 was used as a starting material, it was found that the steep weight decrease peak appeared at ca. 350 deg. C and the uranium volatilized completely. This result suggests that fluorination of U 3 O 8 occurs at this temperature forming UF 6 . Uranium trioxide showed the similar fluorination behavior to that of U 3 O 8

Thermal analysis of thermo-gravimetric measurements of spent nuclear fuel oxidation rates

International Nuclear Information System (INIS)

Cramer, E.R.

1997-01-01

A detailed thermal analysis was completed of the sample temperatures in the Thermo-Gravimetric Analysis (TGA) system used to measure irradiated N Reactor fuel oxidation rates. Sample temperatures during the oxidation process did not show the increase which was postulated as a result of the exothermic reactions. The analysis shows the axial conduction of heat in the sample holder effectively removes the added heat and only a very small, i.e., <10 C, increase in temperature is calculated. A room temperature evaporation test with water showed the sample thermocouple sensitivity to be more than adequate to account for a temperature change of approximately 5 C. Therefore, measured temperatures in the TGA are within approximately 10 C of the actual sample temperatures and no adjustments to reported data to account for the heat input from the oxidation process are necessary

A simple, sensitive graphical method of treating thermogravimetric analysis data

Science.gov (United States)

Abraham Broido

1969-01-01

Thermogravimetric Analysis (TGA) is finding increasing utility in investigations of the pyrolysis and combustion behavior of materuals. Although a theoretical treatment of the TGA behavior of an idealized reaction is relatively straight-forward, major complications can be introduced when the reactions are complex, e.g., in the pyrolysis of cellulose, and when...

Characteristics and kinetic studies of Hydrilla verticillata pyrolysis via thermogravimetric analysis.

Science.gov (United States)

Hu, Zhiquan; Chen, Zhihua; Li, Genbao; Chen, Xiaojuan; Hu, Mian; Laghari, Mahmood; Wang, Xun; Guo, Dabin

2015-10-01

The pyrolysis characteristics and kinetic of Hydrilla verticillata (HV) have been investigated using non-isothermal thermogravimetric analysis. The results showed that the pyrolysis behavior of HV can be divided into two independent stages. The kinetics of Stage I was investigated using a distributed activation energy model (DAEM) with discrete 99 first-order reactions. Stage II was an independent stage which corresponds to the decomposition of calcium oxalate, whose kinetics was studied using iso-conversional method together with compensation effect and master-plots method. The activation energies ranged from 92.39 to 506.17 and 190.42 to 222.48 kJ/mol for the first and second stages respectively. Calculated data gave very good fit to the experimental data. Copyright © 2015 Elsevier Ltd. All rights reserved.

Automation of a thermogravimetric equipment

International Nuclear Information System (INIS)

Mussio, L.; Castiglioni, J.; Diano, W.

1987-01-01

A low cost automation of some instruments by means of simple electronic circuits and a microcomputer Apple IIe. type is discussed. The electronic circuits described are: a) a position detector including phototransistors connected as differential amplifier; b) a current source that, using the error signal of the position detector, changes the current through the coil of an electromagnetic balance to restore its zero position; c) a proportional temperature controller, zero volt switching to drive a furnace to a desired temperature; d) an interface temperature regulator-microcomputer to control the temperature regulator by software; e) a multiplexer for an analog input of a commercial interface. Those circuits are applied in a thermogravimetric equipment used also for vapours adsorption. A program in block diagram form is included and is able to record change of mass, time, furnace temperature and to drive the temperature regulator in order to have the heating rates or the temperature plateaux needed for the experiment. (author) [pt

Catalytic thermal decomposition of polyethylene determined by thermogravimetric treatment

International Nuclear Information System (INIS)

Nisar, J.; Khan, M.S.; Khan, M.A.

2014-01-01

In this study low density polyethylene (LDPE) has been studied by thermogravimetric analysis (TGA) using commercially available oxides as catalysts. TGA experiments were used to evaluate the activity of different catalysts on low density polyethylene (LDPE) degradation and to study the effect in terms of type and amount of catalyst used. All the catalysts used improved the pyrolysis of LDPE. The reaction rates were found to increase with increase in amount of catalyst. Among the catalysts used, alumina acidic active catalyst performed better at all four fractions. Moreover, alumina acidic active reduced weight loss temperature better than others tested catalysts. The effect of alumina neutral catalyst on the pyrolysis of LDPE is less pronounced due to its small surface area and pore size. The effect of these catalysts showed that surface area, number of acidic sites and pore size were found as the key factors for the energy efficient degradation of polymers. (author)

Comparative thermogravimetric analyses of co-combustion of textile dyeing sludge and sugarcane bagasse in carbon dioxide/oxygen and nitrogen/oxygen atmospheres: Thermal conversion characteristics, kinetics, and thermodynamics.

Science.gov (United States)

Xie, Wenhao; Wen, Shaoting; Liu, Jingyong; Xie, Wuming; Kuo, Jiahong; Lu, Xingwen; Sun, Shuiyu; Chang, Kenlin; Buyukada, Musa; Evrendilek, Fatih

2018-05-01

Thermodynamic and kinetic parameters of co-combustion of textile dyeing sludge (TDS) and sugarcane bagasse (SB) were studied using thermogravimetric analysis in CO 2 /O 2 and N 2 /O 2 atmospheres. Our results showed that the comprehensive combustion characteristic index (CCI) of the blends was improved by 1.71-4.32 times. With the increased O 2 concentration, co-combustion peak temperature decreased from 329.7 to 318.2 °C, with an increase in its maximum weight loss rate from 10.04 to 14.99%/min and its CCI by 1.31 times (β = 20 °C·min -1 ). To evaluate the co-combustion characteristics, thermodynamic and kinetic parameters (entropy, Gibbs free energy and enthalpy changes, and apparent activation energy) were obtained in the five atmospheres. The lowest apparent activation energy of the TB64 blend was obtained in oxy-fuel atmosphere (CO 2 /O 2  = 7/3). Copyright © 2018 Elsevier Ltd. All rights reserved.

Heater-Integrated Cantilevers for Nano-Samples Thermogravimetric Analysis

Science.gov (United States)

Toffoli, Valeria; Carrato, Sergio; Lee, Dongkyu; Jeon, Sangmin; Lazzarino, Marco

2013-01-01

The design and characteristics of a micro-system for thermogravimetric analysis (TGA) in which heater, temperature sensor and mass sensor are integrated into a single device are presented. The system consists of a suspended cantilever that incorporates a microfabricated resistor, used as both heater and thermometer. A three-dimensional finite element analysis was used to define the structure parameters. TGA sensors were fabricated by standard microlithographic techniques and tested using milli-Q water and polyurethane microcapsule. The results demonstrated that our approach provides a faster and more sensitive TGA with respect to commercial systems.

Thermogravimetric study of rare earth concentrates

International Nuclear Information System (INIS)

Delyagejd, V.V.; Anisimova, V.N.; Eremenko, Z.V.; Kutsev, V.S.

1974-01-01

Methods of thermogravimetric, chemical and phase analysis were used in measuring the concentration of rare-earth elements of different origins. At temperatures 400-800 deg C a gradual decomposition of fluorocarbonates takes place leading to the formation of derivatives of corresponding oxides and oxyfluorides. For concentrates containing siderite the process takes place at 550-600 deg C followed by oxidation of bivalent iron into trivalent state. Reaction of rare-earth elements with sodium carbonate and the increase in the concentration of the latter results in a narrowing down of the interval of temperatures at which decomposition takes place. Under these conditions an intense reaction and a fusion take place leading to the formation of eutectic at 500-600 deg C and further synthesis of sodium fluoride and oxyfluoride derivatives of calcium and rare-earth elements

Preparation, thermogravimetric study and infrared spectra of rare earth acetates

International Nuclear Information System (INIS)

Graehlert, X.; Starke, M.

1992-01-01

The anhydrous and the hydrated acetates of Ho, Er, Tm, Yb and Lu have been prepared. The compounds obtained have been investigated by thermogravimetric analysis and infrared spectroscopy. The thermal decomposition of the rare earth acetates may proceed via various steps. It depends on both the number of crystal water molecules in the acetates and the rare earth element's behaviour. (orig.)

Dominant thermogravimetric signatures of lignin in cashew shell as compared to cashew shell cake.

Science.gov (United States)

Gangil, Sandip

2014-03-01

Dominant thermogravimetric signatures related to lignin were observed in cashew shell as compared to these signatures in cashew shell cake. The phenomenon of weakening of lignin from cashew shell to cashew shell cake was explained on the basis of changes in the activation energies. The pertinent temperature regimes responsible for the release of different constituents of both the bio-materials were identified and compared. The activation energies of cashew shell and cashew shell cake were compared using Kissinger-Akahira-Sunose method. Thermogravimetric profiling of cashew shell and cashew shell cake indicated that these were different kinds of bio-materials. Copyright © 2013 Elsevier Ltd. All rights reserved.

Mechanism study on cellulose pyrolysis using thermogravimetric analysis coupled with infrared spectroscopy

Institute of Scientific and Technical Information of China (English)

WANG Shurong; LIU Qian; LUO Zhongyang; WEN Lihua; CEN Kefa

2007-01-01

Based on the investigation of the polysaccharide structure of cellulose by using Fourier transform spectrum analysis,the pyrolysis behaviour of cellulose was studied at a heating rate of 20 K/min by thermogravimetric (TG) analysis coupled with Fourier transform infrared (FTIR) spectroscopy.Experimental results show that the decomposition of cellulose mainly occurs at the temperature range of 550-670 K.The weight loss becomes quite slow when the temperature increases further up to 680 K and the amount of residue reaches a mass percent of 14.7%.The FTIR analysis shows that free water is released first during cellulose pyrolysis,followed by depolymerization and dehydration.Glucosidic bond and carbon-carbon bond break into a series of hydrocarbons,alcohols,aldehydes,acids,etc.Subsequently these large-molecule compounds decompose further into gases,such as methane and carbon monoxide.

Use of a fluidized bed combustor and thermogravimetric analyzer for the study of coal ignition temperature

International Nuclear Information System (INIS)

Ávila, Ivonete; Crnkovic, Paula M.; Luna, Carlos M.R.; Milioli, Fernando E.

2017-01-01

Highlights: • Coal ignition tests were conducted in a fluidized bed and thermogravimetric conditions. • The use of two different ignition criteria showed a similar coal ignition temperature. • Coal ignition temperature was obtained by the changes of gas concentrations in FBC. • Ignition temperatures were associated with the activation energy of coal combustion. - Abstract: Ignition experiments with two bituminous coals were carried out in an atmospheric bubbling fluidized bed combustor (FBC) and a thermogravimetric analyzer (TGA). In the FBC tests, the rapid increase in O_2, CO_2, and SO_2 concentrations is an indication of the coal ignition. In the TGA technique, the ignition temperature was determined by the evaluation of the TGA curves in both combustion and pyrolysis processes. Model-Free Kinetics was applied and the coal ignition temperatures were associated with changes in the activation energy values during the combustion process. The results show the coal with the lowest activation energy also showed the lowest ignition temperature, highest values of volatile content and a higher heating value. The application of two different ignition criteria (TGA and FBC) resulted in similar ignition temperatures. The FBC curves indicated the high volatile coal ignites in the freeboard, i.e. during the feeding in the reactor, whereas the low volatile coal ignites in the bed. Finally, the physicochemical characteristics of the investigated coal types were correlated with their reactivities for the prediction of the ignition temperatures behaviors under different operating conditions as those in FBC.

Thermogravimetric and nuclear magnetic resonance study of hydrated Na-β''-alumina

International Nuclear Information System (INIS)

Donoso, P.; Panepucci, H.; Gobato, Y.G.; Oliveira, L.N.; Souza, D.P.F. de

1990-01-01

This paper reports thermogravimetric and proton spin-lattice relaxation times measurement of hydrated Na-β''-alumina, which yield information about the identification of the sites where the loosely bound water molecules are located in the polycrystalline sample. It examines also the influence of impurities on the motion of the protons. (autor) [pt

Strategy for thermo-gravimetric analysis of K East fuel samples

International Nuclear Information System (INIS)

Lawrence, L.A.

1997-01-01

A strategy was developed for the Thermo-Gravimetric Analysis (TGA) testing of K East fuel samples for oxidation rate determinations. Tests will first establish if there are any differences for dry air oxidation between the K West and K East fuel. These tests will be followed by moist inert gas oxidation rate measurements. The final series of tests will consider pure water vapor i.e., steam

Thermogravimetric analysis of fuel film evaporation

Institute of Scientific and Technical Information of China (English)

HU Zongjie; LI Liguang; YU Shui

2006-01-01

Thermogravimetric analysis (TGA) was compared with the petrochemical distillation measurement method to better understand the characteristics of fuel film evaporation at different wall tem- peratures. The film evaporation characteristics of 90# gasoline, 93# gasoline and 0# diesel with different initial thicknesses were investigated at different environmental fluxes and heating rates. The influences of heating rate, film thickness and environmental flux on fuel film evaporation for these fuels were found. The results showed that the environmental conditions in TGA were similar to those for fuel films in the internal combustion engines, so data from TGA were suitable for the analysis of fuel film evaporation. TGA could simulate the key influencing factors for fuel film evaporation and could investigate the basic quantificational effect of heating rate and film thickness. To get a rapid and sufficient fuel film evaporation, sufficiently high wall temperature is necessary. Evaporation time decreases at a high heating rate and thin film thickness, and intense gas flow is important to promoting fuel film evaporation. Data from TGA at a heating rate of 100℃/min are fit to analyze the diesel film evaporation during cold-start and warming-up. Due to the tense molecular interactions, the evaporation sequence could not be strictly divided according to the boiling points of each component for multicomponent dissolved mixture during the quick evaporation process, and the heavier components could vaporize before reaching their boiling points. The 0# diesel film would fully evaporate when the wall temperature is beyond 250℃.

Heater-Integrated Cantilevers for Nano-Samples Thermogravimetric Analysis

Directory of Open Access Journals (Sweden)

Valeria Toffoli

2013-12-01

Full Text Available The design and characteristics of a micro-system for thermogravimetric analysis (TGA in which heater, temperature sensor and mass sensor are integrated into a single device are presented. The system consists of a suspended cantilever that incorporates a microfabricated resistor, used as both heater and thermometer. A three-dimensional finite element analysis was used to define the structure parameters. TGA sensors were fabricated by standard microlithographic techniques and tested using milli-Q water and polyurethane microcapsule. The results demonstrated that our approach provides a faster and more sensitive TGA with respect to commercial systems.

Curie temperature determination via thermogravimetric and continuous wavelet transformation analysis

Energy Technology Data Exchange (ETDEWEB)

Hasier, John; Nash, Philip [Thermal Processing Technology Center, IIT, Chicago, IL (United States); Riolo, Maria Annichia [University of Michigan, Center for the Study of Complex Systems, Ann Arbor, MI (United States)

2017-12-15

A cost effective method for conversion of a vertical tube thermogravimetric analysis system into a magnetic balance capable of measuring Curie Temperatures is presented. Reference and preliminary experimental data generated using this system is analyzed via a general-purpose wavelet based Curie point edge detection technique allowing for enhanced speed, ease and repeatability of magnetic balance data analysis. The Curie temperatures for a number of Heusler compounds are reported. (orig.)

Automation of a McBain-Bakr-type thermogravimetric analyzer using a digital image correlation technique

International Nuclear Information System (INIS)

Trexler, M.D.; Sanders, T.H. Jr.; Singh, P.M.

2006-01-01

Thermogravimetric analysis was used to obtain corrosion kinetics data for several materials in high-temperature environments. A thermogravimetric analyzer has been developed that uses a McBain-Bakr quartz spring balance in conjunction with a digital image acquisition and analysis package to accurately characterize materials through image correlation. This provides a new method for automatically measuring mass changes continuously with a variable resolution depending on the spring component. The decomposition of calcium oxalate was used to verify the validity of the technique. The results show two reactions, whose reaction temperatures were determined by the intercept method, upon heating to 650 deg. C. The mass loss at the first reaction temperature, 200 deg. C, was 20% and a 30% loss was observed at 500 deg. C. Comparison of the experimentally obtained results with those of other researchers who used commercial instruments suggests that the method of using digital image analysis in conjunction with a spring to monitor mass change is a viable and accurate replacement for automatic electrobalances and cathetometers for thermal analysis of materials. Additional comparison between corrosion tests performed on SA210 steel in H 2 S using both a commercial thermobalance and the developed technique confirmed that high-temperature corrosion can be monitored accurately with the proposed method

A comprehensive physicochemical, thermal, and spectroscopic characterization of zinc (II) chloride using X-ray diffraction, particle size distribution, differential scanning calorimetry, thermogravimetric analysis/differential thermogravimetric analysis, ultraviolet-visible, and Fourier transform-infrared spectroscopy.

Science.gov (United States)

Trivedi, Mahendra Kumar; Sethi, Kalyan Kumar; Panda, Parthasarathi; Jana, Snehasis

2017-01-01

Zinc chloride is an important inorganic compound used as a source of zinc and has other numerous industrial applications. Unfortunately, it lacks reliable and accurate physicochemical, thermal, and spectral characterization information altogether. Hence, the authors tried to explore in-depth characterization of zinc chloride using the modern analytical technique. The analysis of zinc chloride was performed using powder X-ray diffraction (PXRD), particle size distribution, differential scanning calorimetry (DSC), thermogravimetric analysis/differential thermogravimetric analysis (TGA/DTG), ultraviolet-visible spectroscopy (UV-vis), and Fourier transform-infrared (FT-IR) analytical techniques. The PXRD patterns showed well-defined, narrow, sharp, and the significant peaks. The crystallite size was found in the range of 14.70-55.40 nm and showed average crystallite size of 41.34 nm. The average particle size was found to be of 1.123 ( d 10 ), 3.025 ( d 50 ), and 6.712 ( d 90 ) μm and average surface area of 2.71 m 2 /g. The span and relative span values were 5.849 μm and 1.93, respectively. The DSC thermogram showed a small endothermic inflation at 308.10°C with the latent heat (ΔH) of fusion 28.52 J/g. An exothermic reaction was observed at 449.32°C with the ΔH of decomposition 66.10 J/g. The TGA revealed two steps of the thermal degradation and lost 8.207 and 89.72% of weight in the first and second step of degradation, respectively. Similarly, the DTG analysis disclosed T max at 508.21°C. The UV-vis spectrum showed absorbance maxima at 197.60 nm (λ max ), and FT-IR spectrum showed a peak at 511/cm might be due to the Zn-Cl stretching. These in-depth, comprehensive data would be very much useful in all stages of nutraceuticals/pharmaceuticals formulation research and development and other industrial applications.

Pyrolysis kinetics investigation of Malaysian based biomass with non-isothermal thermogravimetric analysis (TGA)

International Nuclear Information System (INIS)

Seyed Shahabeddin Nehzati; Dayang Radiah Awang Biak; Wan Azlina Wan Abdul Karim Ghani; Mohd Amran Mohd Salleh

2010-01-01

Full text: Biomass is currently being used as a sustainable energy source. Otherwise the scarceness of fossil fuel sources and the demand for environmental responsibility force the industries to use biomass as an alternate source of energy. Pyrolysis is the first step of biomass conversion and well understanding of this process can develop the biomass conversion such as gasification, liquefaction, carbonization and combustion .TGA studies of Malaysian based biomass have been carried out. TGA studies provide important insight on the thermochemical behavior of specific solid waste. The results of non-isothermal thermogravimetric analysis of palm kernel shell, coconut shell and bagasse, carried out at heating rates of 10 degree Celsius/ min, 20 degree Celsius/ min and 50 degree Celsius/ min, to ramp the temperature from 30 to 1000 were analysed. The TGA studies were carried out in an inert atmosphere of nitrogen. Arrhenius parameters were estimated by 3 different models namely Kissinger model, three-pseudo component and DEAM model the estimated values and the models were compared. The results show that the three-pseudo component model has a good agreement with the experimental results, indicating that ligno celluloses components in the mixture behave in the same way as they do separately. Also it is seen that the decomposition process shifts to higher temperatures at higher heating rates as a result of the competing effects of heat and mass transfer to the material. (Author)

Thermogravimetric measurements of liquid vapor pressure

International Nuclear Information System (INIS)

Rong Yunhong; Gregson, Christopher M.; Parker, Alan

2012-01-01

Highlights: ► Rapid determination of vapor pressure by TGA. ► Demonstration of limitations of currently available approaches in literature. ► New model for vapor pressure assessment of small size samples in TGA. ► New model accounts for vapor diffusion and sample geometry and measures vapor pressure normally within 10%. - Abstract: A method was developed using thermo-gravimetric analysis (TGA) to determine the vapor pressure of volatile liquids. This is achieved by measuring the rate of evaporation (mass loss) of a pure liquid contained within a cylindrical pan. The influence of factors like sample geometry and vapor diffusion on evaporation rate are discussed. The measurement can be performed across a wide range of temperature yielding reasonable results up to 10 kPa. This approach may be useful as a rapid and automatable method for measuring the volatility of flavor and fragrance raw materials.

Thermogravimetric analysis of co-combustion between microalgae and textile dyeing sludge.

Science.gov (United States)

Peng, Xiaowei; Ma, Xiaoqian; Xu, Zhibin

2015-03-01

The synergistic interaction and kinetics of microalgae, textile dyeing sludge and their blends were investigated under combustion condition by thermogravimetric analysis. The textile dyeing sludge was blended with microalgae in the range of 10-90wt.% to investigate their co-combustion behavior. Results showed that the synergistic interaction between microalgae and textile dyeing sludge improved the char catalytic effect and alkali metals melt-induced effect on the decomposition of textile dyeing sludge residue at high temperature of 530-800°C. As the heating rate increasing, the entire combustion process was delayed but the combustion intensity was enhanced. The lowest average activation energy was obtained when the percentage of microalgae was 60%, which was 227.1kJ/mol by OFW and 227.4kJ/mol by KAS, respectively. Copyright © 2015 Elsevier Ltd. All rights reserved.

Pyrolysis and combustion kinetics of lycopodium particles in thermogravimetric analysis

Institute of Scientific and Technical Information of China (English)

Seyed Alireza Mostafavi; Sadjad Salavati; Hossein Beidaghy Dizaji; Mehdi Bidabadi

2015-01-01

Biomass is a kind of renewable energy which is used increasingly in different types of combustion systems or in the production of fuels like bio-oil. Lycopodium is a cellulosic particle, with good combustion properties, of which microscopic images show that these particles have spherical shapes with identical diameters of 31 μm. The measured density of these particles is 1.0779 g/cm2. Lycopodium particles contain 64.06% carbon, 25.56% oxygen, 8.55% hydrogen and 1.83% nitrogen, and no sulfur. Thermogravimetric analysis in the nitrogen environment indicates that the maximum of particle mass reduction occurs in the temperature range of 250−550 °C where the maximum mass reduction in the DTG diagrams also occurs in. In the oxygen environment, an additional peak can also be observed in the temperature range of 500−600 °C, which points to solid phase combustion and ignition temperature of lycopodium particles. The kinetics of reactions is determined by curve fitting and minimization of error.

Thermogravimetric analysis of the beryllium/steam reaction

Energy Technology Data Exchange (ETDEWEB)

Druyts, Frank E-mail: fdruyts@sckcen.be; Iseghem, Pierre van

2000-11-01

In view of the safety assessment of new fusion reactor designs, kinetic data are needed on the beryllium/steam reaction. Therefore, thermogravimetric analysis was used to determine the reactivity of beryllium in steam as a function of temperature, irradiation history and porosity of the samples. To this purpose, reference unirradiated S-200 VHP beryllium samples were compared with specimens irradiated in the BR2 reactor up to fast neutron fluences (E>1 MeV) of respectively 1.6x10{sup 21} n cm{sup -2} (resulting in a helium content of 300 appm He and a theoretical density of 99.9%) and 4x10{sup 22} n cm{sup -2} (21000 appm He, 97.2% theoretical density). Kinetics were parabolic for all tested beryllium types at 600 deg. C. At 700 deg. C, kinetics were parabolic for the unirradiated and irradiated 99.9% dense beryllium, and accelerating/linear for the irradiated 97.2% material. At 800 deg. C, all samples showed accelerating/linear behaviour. There was no influence of porosity on the reaction rate of beryllium in steam within the limited investigated density range, except at 700 deg. C, where the measured reaction rate for the irradiated 97.2% dense samples is an order of magnitude higher than for the irradiated 99.9% dense specimens.

A preliminary high-pressure thermogravimetric study of combustion reactivity of a Collie coal char

Energy Technology Data Exchange (ETDEWEB)

Chan, Yii Leng; Zhang, Zhezi; Zhu, Mingming; Zhang, Dongke [Western Australia Univ., Crawley, WA (Australia). Centre for Energy (M473); Luan, Chao [Western Australia Univ., Crawley, WA (Australia). Centre for Energy (M473); Tsinghua Univ., Beijing (China). Inst. of Thermal Engineering; You, Changfu [Tsinghua Univ., Beijing (China). Inst. of Thermal Engineering

2013-07-01

The effect of pressure(up to 20 bar)on the reactivity of a char(150-160 {mu}m) produced from Western Australian Collie coal has been studied using a high-pressure thermogravimetric analyser (HP TGA). The pressure demonstrated a positive effect in enhancing char combustion reactivities.Kinetic parameters have been determined from the experimental data.The apparent reaction order was found to be approximately 0.7 and the apparent activation energies were 91.0 kJ/mol at atmospheric pressure and 1.5 kJ/mol at an elevated pressure(10 bar),indicating a shift in the control regimes of the reaction at elevated pressures.The lumped effect of the sample size, bulk diffusion,interparticle and intraparticle diffusion at the elevated pressures played an important role in reducing the mass transfer during the HP-TGA experimentation.Thus the activation energy calculated at elevated pressures may not represent the intrinsic activation energy of the char particles but the apparent values of the bulk of the samples.

Characterization and thermogravimetric analysis of lanthanide hexafluoroacetylacetone chelates.

Science.gov (United States)

Shahbazi, Shayan; Stratz, S Adam; Auxier, John D; Hanson, Daniel E; Marsh, Matthew L; Hall, Howard L

2017-01-01

This work reports the thermodynamic characterizations of organometallic species as a vehicle for the rapid separation of volatile nuclear fission products via gas chromatography due to differences in adsorption enthalpy. Because adsorption and sublimation thermodynamics are linearly correlated, there is considerable motivation to determine sublimation enthalpies. A method of isothermal thermogravimetric analysis, TGA-MS and melting point analysis are employed on thirteen lanthanide 1,1,1,5,5,5-hexafluoroacetylacetone complexes to determine sublimation enthalpies. An empirical correlation is used to estimate adsorption enthalpies of lanthanide complexes on a quartz column from the sublimation data. Additionally, four chelates are characterized by SC-XRD, elemental analysis, FTIR and NMR.

Pyrolysis behaviors and kinetic studies on Eucalyptus residues using thermogravimetric analysis

International Nuclear Information System (INIS)

Chen, Zhihua; Zhu, Quanjie; Wang, Xun; Xiao, Bo; Liu, Shiming

2015-01-01

Highlights: • The first study on pyrolysis characteristics and kinetic of Eucalyptus residues. • Pyrolysis process can be divided into three stages using differential DTG method. • A new modified discrete DAEM showed better than Gaussian DAEM for kinetic studies. • Variations of activation energy reveal the mechanism change during pyrolysis process. - Abstract: The pyrolysis behaviors and kinetics of Eucalyptus leaves (EL), Eucalyptus bark (EB) and Eucalyptus sawdust (ESD) were investigated by using thermogravimetric analysis (TGA) technique. Three stages for EL, EB and ESD pyrolysis have been divided using differential derivative thermogravimetric (DDTG) method and the second stage is the main pyrolysis process with approximately 86.93% (EL), 88.96% (EB) and 97.84% (ESD) weight loss percentages. Kinetic parameters of Gaussian distributed activation energy model (DAEM) for EL, EB and ESD pyrolysis are: distributed centers (E_0) of 141.15 kJ/mol (EL), 149.21 kJ/mol (EB), 175.79 kJ/mol (ESD), standard deviations (σ) of 18.35 kJ/mol (EL), 18.37 kJ/mol (EB), 14.41 kJ/mol (ESD) and pre-exponential factors (A) of 1.15E+10 s"−"1 (EL), 4.34E+10 s"−"1 (EB), 7.44E+12 s"−"1 (ESD). A new modified discrete DAEM was performed and showed excellent fits to experimental data than Gaussian DAEM. According to the modified discrete DAEM, the activation energies are in ranges of 122.67–308.64 kJ/mol, 118.72–410.80 kJ/mol and 108.39–192.93 kJ/mol for EL, EB and ESD pyrolysis, respectively. The pre-exponential factors of discrete DAEM have wide ranges of 4.84E+13–6.12E+22 s"−"1 (EL), 1.91E+12–4.51E+25 s"−"1 (EB) and 63.43–4.36E+11 s"−"1 (ESD). The variation of activation energy versus conversion reveals the mechanism change during pyrolysis process. The kinetic data would be of immense benefit to model, design and develop suitable thermo-chemical systems for the application of Eucalyptus residues.

Rapidly assessing the activation conditions and porosity of metal-organic frameworks using thermogravimetric analysis.

Science.gov (United States)

McDonald, Thomas M; Bloch, Eric D; Long, Jeffrey R

2015-03-25

A methodology utilizing a thermogravimetric analyzer to monitor propane uptake following incremental increases of the temperature is demonstrated as a means of rapidly identifying porous materials and determining the optimum activation conditions of metal-organic frameworks.

Quantitation of Surface Coating on Nanoparticles Using Thermogravimetric Analysis.

Science.gov (United States)

Dongargaonkar, Alpana A; Clogston, Jeffrey D

2018-01-01

Nanoparticles are critical components in nanomedicine and nanotherapeutic applications. Some nanoparticles, such as metallic nanoparticles, consist of a surface coating or surface modification to aid in its dispersion and stability. This surface coating may affect the behavior of nanoparticles in a biological environment, thus it is important to measure. Thermogravimetric analysis (TGA) can be used to determine the amount of coating on the surface of the nanoparticle. TGA experiments run under inert atmosphere can also be used to determine residual metal content present in the sample. In this chapter, the TGA technique and experimental method are described.

Thermogravimetric analysis, PXRD, EDX and XPS study of chrysocolla (Cu,Al)2H2Si2O5(OH)4·nH2O-structural implications

International Nuclear Information System (INIS)

Frost, Ray L.; Xi, Yunfei; Wood, Barry J.

2012-01-01

Highlights: ► We have undertaken a TG X PS study of the mineral chrysocolla. ► The chemical bonding of Cu, O and Si has been determined. ► It is concluded that chrysocolla is a mineral in its own right. ► It is not a colloidal mixture of spertiniite and amorphous silica. - Abstract: Selected chrysocolla mineral samples from different origins have been studied by using PXRD, SEM, EDX and XPS. The XRD patterns show that the chrysocolla mineral samples are non-diffracting and no other phases are present in the minerals, thus showing the chrysocolla samples are pure. SEM analyses show the chrysocolla surfaces are featureless. EDX analyses enable the formulae of the chrysocolla samples to be calculated. The thermal decomposition of the mineral chrysocolla has been studied using a combination of thermogravimetric analysis and derivative thermogravimetric analysis. Five thermal decomposition mass loss steps are observed for the chrysocolla from Arizona (a) at 125 °C with the loss of water, (b) at 340 °C with the loss of hydroxyl units, (c) at 468.5 °C with a further loss of hydroxyls, (d) at 821 °C with oxygen loss and (e) at 895 °C with a further loss of oxygen. The thermal analysis of the chrysocolla from Congo shows mass losses at 125, 275.3, 805.6 and 877.4 °C and for the Nevada chrysocolla, mass loss steps at 268, 333, 463, 786.0 and 817.7 °C are observed. The thermal analysis of spertiniite is very different from that of chrysocolla and thermally decomposes at around 160 °C. XPS shows that there are two different copper species present, one which is bonded to oxygen and one to a hydroxyl unit. The O 1s is broad and very symmetrical suggesting two O species of equal number. The bond energy of 102.9 eV for the Si 2p suggests that it is in the form of a silicate. The bond energy is much higher for silicas around ∼103.5 eV. The reported value for silica gel has Si 2p at 103.4 eV. The combination of TG, PXRD, EDX and XPS adds to our fundamental

Synthesis, thermogravimetric, spectroscopic and theoretical characterization of copper(II) complex with 4-chloro-2-nitrobenzenosulfonamide

Science.gov (United States)

Camí, G.; Chacón Villalba, E.; Di Santi, Y.; Colinas, P.; Estiu, G.; Soria, D. B.

2011-05-01

4-Chloro-2-nitrobenzenesulfonamide (ClNbsa) was purified and characterized. A new copper(II) complex, [Cu(ClNbsa) 2(NH 3) 2], has been prepared using the sulfonamide as ligand. The thermal behavior of both, the ligand and the Cu(II) complex, was investigated by thermogravimetric analyses (TG) and differential thermal analysis (DT), and the electronic characteristics analyzed by UV-VIS, FTIR, Raman and 1H NMR spectroscopies. The experimental IR, Raman and UV-VIS spectra have been assigned on the basis of DFT calculations at the B3LYP level of theory using the standard (6-31 + G ∗∗) basis set. The geometries have been fully optimized in vacuum and in modeled dimethylsulfoxide (DMSO) solvent, using for the latter a continuum solvation model that reproduced the experimental conditions of the UV-VIS spectroscopy. The theoretical results converged to stable conformations for the free sulfonamide and for the complex, suggesting for the latter a distorted square planar geometry in both environments.

Evaluation of co-pyrolysis petrochemical wastewater sludge with lignite in a thermogravimetric analyzer and a packed-bed reactor: Pyrolysis characteristics, kinetics, and products analysis.

Science.gov (United States)

Mu, Lin; Chen, Jianbiao; Yao, Pikai; Zhou, Dapeng; Zhao, Liang; Yin, Hongchao

2016-12-01

Co-pyrolysis characteristics of petrochemical wastewater sludge and Huolinhe lignite were investigated using thermogravimetric analyzer and packed-bed reactor coupled with Fourier transform infrared spectrometer and gas chromatography. The pyrolysis characteristics of the blends at various sludge blending ratios were compared with those of the individual materials. Thermogravimetric experiments showed that the interactions between the blends were beneficial to generate more residues. In packed-bed reactor, synergetic effects promoted the release of gas products and left less liquid and solid products than those calculated by additive manner. Fourier transform infrared spectrometer analysis showed that main functional groups in chars gradually disappeared with pyrolysis temperatures increasing, and H 2 O, CH 4 , CO, and CO 2 appeared in volatiles during pyrolysis. Gas compositions analysis indicated that, the yields of H 2 and CO clearly increased as the pyrolysis temperature and sludge blending ratio increasing, while the changes of CH 4 and CO 2 yields were relatively complex. Copyright © 2016 Elsevier Ltd. All rights reserved.

Combustion behavior and kinetics of low-lipid microalgae via thermogravimetric analysis.

Science.gov (United States)

Gai, Chao; Liu, Zhengang; Han, Guanghua; Peng, Nana; Fan, Aonan

2015-04-01

Thermogravimetric analysis and differential thermal analysis were employed to investigate combustion characteristics of two low-lipid microalgae, Chlorella pyrenoidosa (CP) and Spirulina platensis (SP) and iso-conversional Starink approach was used to calculate the kinetic parameters in the present study. The results showed that three stages of mass loss, including dehydration, devolatilization and char oxidation, were observed during combustion of both of two low-lipid microalgae. The whole weight loss of combustion of two microalgae was both shifted to higher temperature zones with increased heating rates from 10 to 40 K/min. In the 0.1-0.9 conversion range, the apparent activation energy of CP increased first from 51.96 to 79.53 kJ/mol, then decreased to 55.59 kJ/mol. Finally, it slightly increased to 67.27 kJ/mol. In the case of SP, the apparent activation energy gradually increased from 68.51 to 91.06 kJ/mol. Copyright © 2015 Elsevier Ltd. All rights reserved.

硫化环氧化天然橡胶的热分析%Thermogravimetric Analysis of ENR Vulcanizate

Institute of Scientific and Technical Information of China (English)

张北龙; 陈美; 刘惠伦

2001-01-01

The thermogravimetric analysis of ENR(epoxidized natural rubber) has been carried out byTG-DTG methods at temperature rising rate of 5, 10, 15 and 20 ℃ · rmin-1. The results showed thatthe activation energy of the thermoreaction in flowing air during the course of mass loss wasn＇t alwayskeep rising, but declined at mass loss of 1.0％～10.0％, 20.0％～30.0％ and 70. 0％～80. 0％.

Thermogravimetric studies on alkyl methacrylate polymers and poly(alkyl methacrylate)-grafted polypropylene fibers

International Nuclear Information System (INIS)

Hayakawa, Kiyoshi; Taoda, Hiroshi; Kawase, Kaoru; Tazawa, Masato; Yamakita, Hiromi

1986-01-01

Thermal behavior of several kinds of poly (alkyl methacrylate) and polypropylene-g-poly (alkyl methacrylate) fibers prepared by γ-irradiation was investigated by thermogravimetric measurements with the intermittent analysis of the gaseous products. The degradation of poly (methyl methacrylate) proceeded according to the deploymerization mechanism reproducing the pristine monomer exclusively. The thermogram in inert atmosphere showed the features of a two-step depolymerization, while in air it showed no such a stepwise decrease with the elevating temperature. The dissolution-precipitation treatment of polymer seemed to affect the decomposition behavior. On other alkyl methacrylate polymers, the thermal decomposition generally proceeded also according to the depolymerization mechanism. But, for instance, at least two kinds of products besides its own monomer were formed from poly (isobutyl methacrylate), and their relative fractions differed with the temperature. Polypropylene-g-poly (alkyl methacrylate) fibers showed lowering of initiation temperature of decomposition with the increase in extent of the grafting, and their initiation temperatures of decomposition in air were lower than those in inert atmosphere. (author)

A thermogravimetric analyzer for corrosive atmospheres, and its application to the chlorination of ZrO2-C mixtures

International Nuclear Information System (INIS)

Pasquevich, Daniel; Caneiro, Alberto

1990-01-01

A thermogravimetric analyzer built on the basis of a Cahn 2000 electrobalance, suitable for using with corrosive atmospheres, is reported. The corrections for buoyancy and gas-flow effects, which strongly modify the thermogravimetric curves are discussed. As an application, the kinetics of a reaction between chlorine and a mixture of zirconia and carbon has been studied. It has been able to measure the uptake of chlorine by carbon and the reaction rate within the first 50 seconds. Evidence of a transition to quite a different reaction rate at longer times is presented. (Author)

Characterization of an alkali-treated grass fiber by thermogravimetric and X-ray crystallographic analysis

NARCIS (Netherlands)

De, D.; De, Debapriya

2008-01-01

The thermal behavior of grass fiber was characterized by means of thermogravimetric analysis and differential scanning calorimetry analysis. The results proved that the removal of water-soluble matter improved the thermal behavior of grass fiber over that of unleached fiber, and this was further

Thermogravimetric analytical procedures for characterizing New Zealand and eastern Australian coals

Energy Technology Data Exchange (ETDEWEB)

Benfell, K.E.; Beamish, B.B.; Rodgers, K.A. [University of Auckland, Auckland (New Zealand). Dept. of Geology

1996-09-01

Under tightly constrained experimental conditions (particle size {lt}75 {mu}m, sample mass 5.0 {+-} 0.5 mg), heating rate 15{degree}C min{sup -1}, dry air purge 50 mL min{sup -1}, maximum temperature 900{degree}C a repeatability of {lt} {+-} 2{degree}C, may be achieved for significant temperatures that characterize the differential thermogravimetric burning profiles of typical medium-volatile, bituminous Australian Gondwanan coals and high-volatile, bituminous New Zealand Cretaceous-Tertiary coals.

Pyrolysis of coal, biomass and their blends: performance assessment by thermogravimetric analysis.

Science.gov (United States)

Ferrara, Francesca; Orsini, Alessandro; Plaisant, Alberto; Pettinau, Alberto

2014-11-01

With the aim to support the experimental tests in a gasification pilot plant, the thermal decomposition of coal, biomass and their mixtures has been carried out through a thermogravimetric analysis (TGA) and a simplified kinetic analysis. The TGA of pure fuels indicates the low reactivity of South African coal and the relatively high reactivity of Sardinian Sulcis coal during pyrolysis. Among the tested fuels, biomass (stone pine wood chips) is the most reactive one. These results fully confirm those obtained during the experimental tests in the gasification pilot plant. As for the fuel blends, the analysis shows that the synergic effects between the considered coals and biomass are negligible when they are co-pyrolyzed. The results of the analysis confirm that TGA could be very useful to generally predict the gasification performance and to optimize the experimental campaigns in pilot-scale gasification plants. Copyright © 2014 Elsevier Ltd. All rights reserved.

Investigation of Thermal Behavior for Natural Fibres Reinforced Epoxy using Thermogravimetric and Differential Scanning Calorimetric Analysis

Directory of Open Access Journals (Sweden)

Fauzi F.A.

2016-01-01

Full Text Available This paper presented the research works on the investigation of the thermal behavior of the natural fibres; i.e. pineapple leaf fibre, kenaf fibre and mengkuang fibres reinforced epoxy. The thermogravimetric analysis and differential scanning calorimetric analysis were used to measure the thermal behavior of the treated and untreated pineapple, kenaf and mengkuang fibres reinforced epoxy. The samples for both analysis were subjected to maximum temperature 600°C at the heating rate of 10°C/min. The results showed that the treated fibres show higher maximum peak temperature as compared to the untreated fibres. Additionally, the glass transition temperature showed a lower value for all treated fibre. It can be concluded that investigation of thermal properties of these natural fibres could improve the utilization of natural fibre composites in various applications i.e. sports applications.

Thermogravimetric analysis of anthracite and waste plastics by iso-conversional method

International Nuclear Information System (INIS)

Ren, Shan; Zhang, Jianliang

2013-01-01

Highlights: • Co-combustion kinetic analysis of solid fuels was made by iso-conversional method. • Thermodynamic and kinetic parameters of combustion for blends were determined. • WP can improve the combustion characteristic of high ash anthracite. • Reasonable utilization the energy of WP is important for industrial production. - Abstract: Combustion mechanisms and kinetics of plastics-coal blends with 0, 10, 20, 40 and 100% waste plastics (WP) are studied separately by thermogravimetric analysis (TGA) from ambient temperature to 900 °C in air atmosphere. These blends are combusted at different heating rates. The results indicate that, with the increase of waste plastics content, the combustion processes of blends could be divided into one stage, two stages, three stages and one stage. Meanwhile, the ignition and final temperatures of them both decrease. The maximum weight loss rate of WP is much higher than that of other samples. The iso-conversional method is used for the kinetic analysis of the non-isothermal thermogravimetric data and results indicate that, when the waste plastics content varied from 0% to 40%, the values of activation energy increase from 113.3 kJ mol −1 to 156.0 kJ mol −1 , and the value of activation energy for pure WP is 278.8 kJ mol −1

Thermal decomposition kinetics of sorghum straw via thermogravimetric analysis.

Science.gov (United States)

Dhyani, Vaibhav; Kumar, Jitendra; Bhaskar, Thallada

2017-12-01

The thermal decomposition of sorghum straw was investigated by non-isothermal thermogravimetric analysis, where the determination of kinetic triplet (activation energy, pre-exponential factor, and reaction model), was the key objective. The activation energy was determined using different isoconversional methods: Friedman, Flynn-Wall-Ozawa (FWO), Kissinger-Akahira-Sunose (KAS), Starink, Iterative method of Chai & Chen, Vyazovkin AIC method, and Li & Tang equation. The pre-exponential factor was calculated using Kissinger's equation; while the reaction model was predicted by comparison of z-master plot obtained from experimental values with the theoretical plots. The values of activation energy obtained from isoconversional methods were further used for evaluation of thermodynamic parameters, enthalpy, entropy and Gibbs free energy. Results showed three zones of pyrolysis having average activation energy values of 151.21kJ/mol, 116.15kJ/mol, and 136.65kJ/mol respectively. The data was well fitting with two-dimension 'Valensi' model for conversion values from 0 to 0.4 with a coefficient of determination (R 2 ) value of 0.988, and with third order reaction model for values from 0.4 to 0.9 with an R 2 value of 0.843. Copyright © 2017 Elsevier Ltd. All rights reserved.

Research on Mechanism of Paper Burning by Thermogravimetric Analysis

Institute of Scientific and Technical Information of China (English)

QIN Da; HAN Xingzhou; WANG Xiaoguang; QI Fengliang; WANG Zijie; GUO Zihan; HAO Hongguang

2015-01-01

The examination of charred document is a challenge and usually requires a careful application of certain scientific techniques due to its unstable property. To address this issue, the mechanism of paper burning was studied in this paper. Here thermal-gravimetry (TG) was applied to investigate five kinds of paper, along with their TG and derivative thermogravimetric curve (DTG) observed at different atmospheric conditions. The results showed that the shape of curves, albeit similar, varied with the physical and chemical composition of paper. In the burning process, dehydration and de-polymerization are the two main pathways for cellulose, the major ingredient of paper. The heating rate indicated little influence on the curves while the sort of atmosphere worked strongly. The reason is due to the lack of tar oxidation when nitrogen used as the atmospheric environment. At moderate temperature, de-polymerization prevails and the tar can be observed. With temperature increasing, the tar and cellulose are further decomposed, leading to products of high boiling-point. According to the results, the charred document can be classified as one of the dehydrated, tarred, charred and ashed. Except the ashed stage, the other three can be handled and the writing whereon can be deciphered. The results exposed hereof may provide a fundamental for examining and deciphering charred document.

Synthesis, characterization and thermogravimetric study of zinc and cadmium acetates-polyaniline hybrids

International Nuclear Information System (INIS)

Fernandes de Farias, Robson

2004-01-01

By dissolution of respective acetates and conducting polymer in dimethylformamide, homogeneous zinc acetate and cadmium acetate-polyaniline (PANI) hybrids were synthesized and characterized by infrared spectroscopy, thermogravimetry and SEM microscopy. The infrared spectra suggests that there are interactions between PANI and the metal cations involving both, imine and amine nitrogens in a typical Lewis acid-base reaction. The thermogravimetric degradation profile of the synthesized hybrids resembles those exhibited by PANI samples

Determination of nanoparticle surface coatings and nanoparticle purity using microscale thermogravimetric analysis.

Science.gov (United States)

Mansfield, Elisabeth; Tyner, Katherine M; Poling, Christopher M; Blacklock, Jenifer L

2014-02-04

The use of nanoparticles in some applications (i.e., nanomedical, nanofiltration, or nanoelectronic) requires small samples with well-known purities and composition. In addition, when nanoparticles are introduced into complex environments (e.g., biological fluids), the particles may become coated with matter, such as proteins or lipid layers. Many of today's analytical techniques are not able to address small-scale samples of nanoparticles to determine purity and the presence of surface coatings. Through the use of an elevated-temperature quartz crystal microbalance (QCM) method we call microscale thermogravimetric analysis, or μ-TGA, the nanoparticle purity, as well as the presence of any surface coatings of nanomaterials, can be measured. Microscale thermogravimetric analysis is used to determine the presence and amount of surface-bound ligand coverage on gold nanoparticles and confirm the presence of a poly(ethylene glycol) coating on SiO2 nanoparticles. Results are compared to traditional analytical techniques to demonstrate reproducibility and validity of μ-TGA for determining the presence of nanoparticle surface coatings. Carbon nanotube samples are also analyzed and compared to conventional TGA. The results demonstrate μ-TGA is a valid method for quantitative determination of the coatings on nanoparticles, and in some cases, can provide purity and compositional data of the nanoparticles themselves.

Determinação da espessura da camada polimérica de fases estacionárias imobilizadas para cromatografia líquida de alta eficiência por termogravimetria Determination of polymeric layer thickness on immobilized stationary phases for high-performance liquid chromatography using thermogravimetric analyses

Directory of Open Access Journals (Sweden)

Anizio M. Faria

2008-01-01

Full Text Available This paper presents a simple and practical thermogravimetric method for determining the layer thickness of immobilized polymer stationary phases used in reversed-phase high-performance liquid chromatography. In this method, the weight loss of different polysiloxanes immobilized onto chromatographic supports, determined over the temperature range 150-650 ºC, demonstrated excellent agreement with the sum of carbon and hydrogen content obtained by elemental analysis. The results presented here suggest that the thermogravimetric procedure is an accurate and precise method to determine the polymeric material content on polymer-coated stationary phases.

Carbon speciation in ash, residual waste and contaminated soil by thermal and chemical analyses.

Science.gov (United States)

Kumpiene, Jurate; Robinson, Ryan; Brännvall, Evelina; Nordmark, Désirée; Bjurström, Henrik; Andreas, Lale; Lagerkvist, Anders; Ecke, Holger

2011-01-01

Carbon in waste can occur as inorganic (IC), organic (OC) and elemental carbon (EC) each having distinct chemical properties and possible environmental effects. In this study, carbon speciation was performed using thermogravimetric analysis (TGA), chemical degradation tests and the standard total organic carbon (TOC) measurement procedures in three types of waste materials (bottom ash, residual waste and contaminated soil). Over 50% of the total carbon (TC) in all studied materials (72% in ash and residual waste, and 59% in soil) was biologically non-reactive or EC as determined by thermogravimetric analyses. The speciation of TOC by chemical degradation also showed a presence of a non-degradable C fraction in all materials (60% of TOC in ash, 30% in residual waste and 13% in soil), though in smaller amounts than those determined by TGA. In principle, chemical degradation method can give an indication of the presence of potentially inert C in various waste materials, while TGA is a more precise technique for C speciation, given that waste-specific method adjustments are made. The standard TOC measurement yields exaggerated estimates of organic carbon and may therefore overestimate the potential environmental impacts (e.g. landfill gas generation) of waste materials in a landfill environment. Copyright © 2010 Elsevier Ltd. All rights reserved.

Chin Shan analyses show advantages of whole pool multi-rack approach

International Nuclear Information System (INIS)

Singh, K.P.; Soler, A.I.

1991-01-01

Nuclear fuel storage racks are essentially thin-walled, cellular structures of prismatic cross-section. Although the details of design vary from one supplier to another, certain key physical attributes are common to all designs. For example, all racks feature square cells of sufficient opening size and height to enable insertion and withdrawal of the fuel assembly. The array of cells is positioned in a vertical orientation and is supported off the pool slab surface by four or more support legs. The spent fuel pool is filled with the individual fuel racks. The plenum created by the support legs is essential for proper cooling of the fuel assemblies stored in the rack, which relies on natural convective cooling to extract the heat emitted by the spent fuel. However, it has the insalutary effect of making it kinematically less stable. Regulatory authorities require careful and comprehensive analysis of the response of the racks under the seismic motions postulated for the pool slab. Results from whole pool multi-rack (WPMR) analyses at the Chin Shan and Oyster Creek nuclear plants point up the potential inadequacies of single rack 3D analyses, and show just how important it is to carry out WPMR simulations, despite their abstruseness and high cost. (author)

Air oxidation of Zr65Cu17.5Ni10Al7.5 in its amorphous and supercooled liquid states, studied by thermogravimetric analysis

International Nuclear Information System (INIS)

Dhawan, A.; Sharma, S.K.; Raetzke, K.; Faupel, F.

2003-01-01

The oxidation behaviour of the bulk amorphous alloy Zr 65 Cu 17.5 Ni 10 Al 7.5 was studied in air at various temperatures in the temperature range 591-732 K using a thermogravimetric analyser (TGA). The oxidation kinetics of the alloy obeys the parabolic rate law showing two different linear regions (in the plots of mass gain versus square root of oxidation time) which are attributed to the amorphous and the supercooled liquid states of the alloy. The value of the activation energy Q for the amorphous state as calculated from the temperature dependence of the rate constants is found to be 1.80±0.1 eV and the corresponding value obtained for the supercooled liquid state is 1.20±0.1 eV. It is suggested that the rate controlling process during oxidation of the amorphous state is the back-diffusion of Ni, and possibly Cu also, while the oxidation in the supercooled liquid state is dominated by the inward diffusion of oxygen. (copyright 2003 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Thermogravimetric Analysis of Effects of High-Content Limstone Addition on Combustion Characteristics of Taixi Anthracite

Institute of Scientific and Technical Information of China (English)

ZHANG Hong; LI Mei; SUN Min; WEI Xian-yong

2004-01-01

Combustion characteristics of Taixi anthracite admixed with high content of limestone addition were investigated with thermogravimetric analysis. The results show that limestone addition has a little promoting effect on the ignition of raw coals as a whole. The addition of limestone is found to significantly accelerate the combustion and burnout of raw coals. The higher the sample mass is, the more significant the effect will be. The results also show that the change of limestone proportion between 45%-80% has little effect on ignition temperatures of coal in the blended samples. Increasing limestone content lowers the temperature corresponding to the maximum weight loss. Although higher maximum mass loss rates are observed with higher limestone content, the effect is found not ascribed to changing limestone addition, but to the decrease of absolute coal mass in the sample. The change of limestone proportion has little effect on its burnout temperature. Mechanism analysis indicates that these phenomena result mainly from improved heat conduction due to limestone addition.

A novel quantification method of pantaprazole sodium monohydrate in sesquihydrate by thermogravimetric analyzer.

Science.gov (United States)

Reddy, V Ranga; Rajmohan, M Anantha; Shilpa, R Laxmi; Raut, Dilip M; Naveenkumar, Kolla; Suryanarayana, M V; Mathad, Vijayavitthal T

2007-04-11

To demonstrate the applicability of thermogravimetric analyzer as a tool for the quantification of pantaprazole sodium monohydrate in sesquihydrate, studies have been conducted. Thermal analysis (DSC, TGA) crystallographic (PXRD) and spectroscopic techniques (FT-IR) were used for the characterization of the polymorphs. Thermogravimetric analysis (TGA) analysis was explored by high-resolution dynamic (Hi-Res-dynamic) and high-resolution modulated (Hi-Res-modulated) test procedures to quantify the hydrate polymorphic mixtures. The two polymorphic forms exhibited significant differences and good resolution in the second derivative thermogram generated by Hi-Res-modulated test procedure. Thus, the TGA with Hi-Res-modulated test procedure was considered for the quantification of monohydrate in sesquihydrate. The calibration plot was constructed from the known mixtures of two polymorphs by plotting the peak area of the second derivative thermogram against the weight percent of monohydrate. Using this novel approach, 1 wt% limit of detection (LOD) was achieved. The polymorphic purity results, obtained by TGA in Hi-Res-modulated test procedure were found to be in good agreement with the results predicted by FT-IR and was comparable with the actual values of the known polymorphic mixtures. The Hi-Res-modulated TGA technique is very simple and easy to perform the analysis.

Method for Determining the Activation Energy Distribution Function of Complex Reactions by Sieving and Thermogravimetric Measurements.

Science.gov (United States)

Bufalo, Gennaro; Ambrosone, Luigi

2016-01-14

A method for studying the kinetics of thermal degradation of complex compounds is suggested. Although the method is applicable to any matrix whose grain size can be measured, herein we focus our investigation on thermogravimetric analysis, under a nitrogen atmosphere, of ground soft wheat and ground maize. The thermogravimetric curves reveal that there are two well-distinct jumps of mass loss. They correspond to volatilization, which is in the temperature range 298-433 K, and decomposition regions go from 450 to 1073 K. Thermal degradation is schematized as a reaction in the solid state whose kinetics is analyzed separately in each of the two regions. By means of a sieving analysis different size fractions of the material are separated and studied. A quasi-Newton fitting algorithm is used to obtain the grain size distribution as best fit to experimental data. The individual fractions are thermogravimetrically analyzed for deriving the functional relationship between activation energy of the degradation reactions and the particle size. Such functional relationship turns out to be crucial to evaluate the moments of the activation energy distribution, which is unknown in terms of the distribution calculated by sieve analysis. From the knowledge of moments one can reconstruct the reaction conversion. The method is applied first to the volatilization region, then to the decomposition region. The comparison with the experimental data reveals that the method reproduces the experimental conversion with an accuracy of 5-10% in the volatilization region and of 3-5% in the decomposition region.

Study on high-silicon boron-containing zeolite by thermogravimetric and IR-spectroscopy techniques

International Nuclear Information System (INIS)

Chukin, G.D.; Nefedov, B.K.; Surin, S.A.; Polinina, E.V.; Khusid, B.L.; Sidel'kovskaya, V.G.

1985-01-01

The structure identity of initial Na-forms of boron-containing and aluminosilicate high-silicon zeolites is established by thermogravimetric and IR-spectroscopy methods. The presence of boron in Na-forms of high-silicon zeolites is shown to lead to reduction of structure thermal stability. It is noted that thermal stability of the H-form of both high-silicon boron-containing and boron-free zeolites is practically equal and considerably higher than that of Na-forms

Kinetic Model of LiFePO4 Formation Using Non-Isothermal Thermogravimetric Analysis

Directory of Open Access Journals (Sweden)

Abdul Halim

2014-03-01

Full Text Available The formation reaction of LiFePO4 from decomposition of precursors LiOH, FeSO4.7H2O and (NH42HPO4 with mol ratio of Li:Fe:P=1:1:1 was investigated. The experiment was carried out by thermogravimetric differential thermal analysis (TG-DTA method using nitrogen as atmosfer at a constant heating rate to obtain kinetic constant parameters. Several heating rates were selected, there are 5, 7, 10, 15, 17.5, 22.5 and 25 °C/min. Activation energy, pre-exponential factor and reaction order were taken using Kissinger method and obtained respectively 56.086 kJ/mol, 6.95×108 min-1, and 1.058. Based on fitting result between reaction model and experiment were obtained that reaction obeyed the three dimension diffusion model. © 2014 BCREC UNDIP. All rights reservedReceived: 19th September 2013; Revised: 9th December 2013; Accepted: 23rd January 2014 [How to Cite: Halim, A., Widiyastuti, W., Setyawan, H., Winardi, S. (2014. Kinetic of LiFePO4 For-mation Using Non-isothermal Thermogravimetric Analysis. Bulletin of Chemical Reaction Engineering & Catalysis, 9 (1: 60-65. (doi:10.9767/bcrec.9.1.5508.60-65][Permalink/DOI: http://dx.doi.org/10.9767/bcrec.9.1.5508.60-65] 

Thermogravimetric study of superconducting YBa2Cu3O9-x in hydrogen

International Nuclear Information System (INIS)

Swaminathan, K.; Janaki, J.; Rao, G.V.N.; Sreedharan, O.M.; Radhakrishnan, T.S.

1988-01-01

The thermogravimetric curve of YBa 2 Cu 3 O 9-x in hydrogen exhibits five steps, the first two corresponding to the reduction of copper oxide to copper by about 683 K (as identified by XRD on quenched samples) followed by three more steps predominantly due to hydration-dehydration behaviour of BaO. The need for blank corrections and the choice of 1223 K as the temperature for the determination of oxygen stoichiometry are discussed. 6 refs.; 2 figs.; 1 table

Characteristics of curcumin using cyclic voltammetry, UV–vis, fluorescence and thermogravimetric analysis

International Nuclear Information System (INIS)

Masek, Anna; Chrzescijanska, Ewa; Zaborski, Marian

2013-01-01

Highlights: • Electrooxidation of curcumin was investigated with cyclic voltammetry. • The curcumin is irreversibly oxidized at the platinum electrode in anhydrous media. • Absorbance, fluorescence and thermogravimetric analysis of curcumin was studied. • The HOMO and Mapped Electron Densities were calculated using HyperChem. • Oxidation mechanism for curcumin proposed. -- Abstract: Curcumin, the yellow, primary bioactive component of turmeric, has recently received attention from chemists due its wide range of potential biological applications as an antioxidant, anti-inflammatory, and anti-carcinogenic agent. The electrochemical behaviour of curcumin at a platinum electrode has been studied by cyclic voltammetry (CV) and differential pulse voltammetry (DPV). The oxidation of curcumin is an irreversible process that proceeds in two steps in 0.1 M (C 4 H 9 ) 4 NClO 4 in acetonitrile. The process of oxidation and its kinetics have been investigated. The rate constant, electron transfer coefficient and diffusion coefficients for the electrochemical oxidation of curcumin were determined. A mechanism for the oxidation of curcumin is proposed. The data obtained are consistent with the current literature and suggest that voltammetric studies on mechanically transferred solids may be a convenient method for elucidating the electrochemical oxidation mechanisms of compounds in anhydrous media. Theoretical calculations regarding the optimization of curcumin, electronic properties like highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) were calculated using with HyperChem software by AM1 semi-empirical method. The properties of curcumin in a homogeneous environment were investigated using spectroscopic techniques and thermogravimetric analysis

Thermogravimetric investigation on characteristic of biomass combustion under the effect of organic calcium compounds.

Science.gov (United States)

Zhang, Lihui; Duan, Feng; Huang, Yaji

2015-01-01

Experiments were conducted in a thermogravimetric analyzer to investigate thermal behavior of different organic calcium compounds (OCCs) and its blended fuels with three kinds of biomass. The effectiveness of synthesized method for OCC was assessed by the pyrolysis test. Effect of the mole ratio of calcium to sulfur on co-combustion characteristics was studied. Results indicated that preparation method of modified calcium acetate (MCA) had high precision and accuracy. Co-combustion characteristic of OCCs blended with biomass was controlled by OCCs' additive amount and the content of volatile matter which is mainly composed of small hydrocarbon molecules. Combustion performance indexes for peanut shell and wheat straw impregnated by OCCs were improved, however, an inverse trend was found for rice husk because of lower additive amount of OCCs. The blended fuel show higher combustion performance indexes compared with combustion of individual biomass, and these indexes decrease with increases of Ca/S ratio. Copyright © 2014 Elsevier Ltd. All rights reserved.

Interactions of coal gangue and pine sawdust during combustion of their blends studied using differential thermogravimetric analysis.

Science.gov (United States)

Zhang, Yuanyuan; Zhang, Zhezi; Zhu, Mingming; Cheng, Fangqin; Zhang, Dongke

2016-08-01

The interactions between coal gangue and pine sawdust during the combustion process were studied using thermogravimetric analysis. The effect of the blending ratio, oxygen concentration and heating rate on the weight loss (TG) and differential thermogravimetric (TGA) profiles was examined. The TG and DTG curves of the blends were not additives of those of the individual materials, suggesting that interactions between coal gangue and pine sawdust had occurred during the combustion, especially in the temperature range of 400-600°C. Kinetic analysis confirmed that the combustion of coal gangue, pine sawdust and their blends was chemical reaction controlled. Further analysis revealed that the interactions between coal gangue and pine sawdust were primarily due to thermal effects rather than structural changes, with the thermal inertia of coal gangue dominating over the behaviour of the blends. The interactions decreased with decreasing the coal gangue ratio in the blend, oxygen concentration and heating rate. Copyright © 2016 Elsevier Ltd. All rights reserved.

Oxy-fuel combustion characteristics and kinetics of microalgae Chlorella vulgaris by thermogravimetric analysis.

Science.gov (United States)

Chen, Chunxiang; Lu, Ziguang; Ma, Xiaoqian; Long, Jun; Peng, Yuning; Hu, Likun; Lu, Quan

2013-09-01

Oxy-fuel or O2/CO2 combustion technology was used to investigate the combustion of Chlorella vulgaris by thermogravimetric analysis (TGA). Oxy-fuel combustion occurs in an O2/CO2 atmosphere instead of an O2/N2 atmosphere and offers an alternative method of C. vulgaris preparation for biofuels processing. Our results show that three stages were observed during C. vulgaris combustion and the main combustion process occurred at the second stage. Compared with a 20%O2/80%N2 atmosphere, the mass loss rate at the DTG peaks (Rp) and the average reaction rate (Rv) in a 20%O2/80%CO2 atmosphere was lower, while the ignition temperature (TI) was higher. As oxygen concentration increases in an O2/CO2 atmosphere, Rp, Rv and the apparent activation energy (E) increases, while TI, the final temperature detected as mass stabilization (Tf) and the residue mass (Mr) decreases; As the heating rate (β) increases, TI, Tf and Rp increase, while Mr decreases. Crown Copyright © 2013. Published by Elsevier Ltd. All rights reserved.

Determination of kinetic parameters of Phlomis bovei de Noé using thermogravimetric analysis.

Science.gov (United States)

Yahiaoui, Meriem; Hadoun, Hocine; Toumert, Idir; Hassani, Aicha

2015-11-01

This paper reports the pyrolysis study of Phlomis bovei biomass by thermogravimetric experiments in order to determine the thermal degradation behavior and kinetic parameters. The weight losses were found to occur in three stages. In the DTG thermograms, an increase of the heating rate tended to delay thermal degradation processes towards higher temperatures. The average values of activation energy and pre-exponential factor calculated from Ozawa-Flynn-Wall, Kissinger-Akahira-Sunose and Kissinger methods are 134.83, 134.06, 223.31kJ/mol and 4.1610(13), 1.1810(10), 2.8110(11)/s, respectively. The three-pseudo-component method shows that the activation energy increases with increasing the heating rate for hemicellulose and cellulose while the activation energy of the lignin decreased with an increase of the heating rate. Predicted results and experimental data exhibit similar tendencies and the three pseudo-components model with n different from unity 1 is recommended as the most suitable for prediction of kinetic behavior of Phlomis bovei de Noé. Copyright © 2015 Elsevier Ltd. All rights reserved.

Biomass Thermogravimetric Analysis: Uncertainty Determination Methodology and Sampling Maps Generation

Science.gov (United States)

Pazó, Jose A.; Granada, Enrique; Saavedra, Ángeles; Eguía, Pablo; Collazo, Joaquín

2010-01-01

The objective of this study was to develop a methodology for the determination of the maximum sampling error and confidence intervals of thermal properties obtained from thermogravimetric analysis (TG), including moisture, volatile matter, fixed carbon and ash content. The sampling procedure of the TG analysis was of particular interest and was conducted with care. The results of the present study were compared to those of a prompt analysis, and a correlation between the mean values and maximum sampling errors of the methods were not observed. In general, low and acceptable levels of uncertainty and error were obtained, demonstrating that the properties evaluated by TG analysis were representative of the overall fuel composition. The accurate determination of the thermal properties of biomass with precise confidence intervals is of particular interest in energetic biomass applications. PMID:20717532

Thermogravimetric kinetics of corn stalk pretreated by oleaginous fungi Cunninghamella echinulata.

Science.gov (United States)

Wu, Jianguo; Gao, Shi; Wan, Jilin; Zeng, Yelin; Ma, Fuying; Zhang, Xiaoyu

2011-04-01

The thermogravimetric and composition of corn stalk pretreated by oleaginous fungi Cunninghamella echinulata had been studied in this paper. Results indicated that pretreatment by oleaginous fungi C. echinulata could decrease the activation energy and make the pyrolysis more efficient and energy-saving. By bio-pretreatment, the contents of elements agreed with the weight loss, sugar content, and oil contents, especially the sulfur content was greatly decreased, greatly eliminating the inventory of gas contamination such as the emission of SOx and making the pyrolysis more environmentally friendly. Therefore, corn stalk with sugar pretreated by oleaginous fungi C. echinulata should be a good pyrolysis material to obtain high quality bio-oil. Copyright © 2011 Elsevier Ltd. All rights reserved.

Thermogravimetric determination of the carbon dioxide reactivity of char from some New Zealand coals and its association with the inorganic geochemistry of the parent coal

Energy Technology Data Exchange (ETDEWEB)

Beamish, B.B.; Shaw, K.J.; Rodgers, K.A.; Newman, J. [University of Auckland, Auckland (New Zealand). Dept. of Geology

1998-02-01

Thermogravimetrically-determined carbon dioxide reactivities of char formed from New Zealand coals, ranging in rank from lignite to high volatile bituminous, vary from 0.12 to 10.63 mg/h/mg on a dry, ash-free basis. The lowest rank subbituminous coal chars have similar reactivities to the lignite coal chars. Calcium content of the char shows the strongest correlation with reactivity, which increases as the calcium content increases. High calcium per se does not directly imply a high char reactivity. Organically-bound calcium catalyses the conversion of carbon to carbon monoxide in the presence of carbon dioxide, whereas calcium present as discrete minerals in the coal matrix e.g., calcite, fails to significantly affect reactivity. Catalytic effects of magnesium, iron, sodium and phosphorous are not as obvious, but can be recognised for individual chars. The thermogravimetric technique provides a fast, reliable analysis that is able to distinguish char reactivity differences between coals, which may be due to any of the above effects. 27 refs., 6 figs., 4 tabs.

Comparative study on pyrolysis of lignocellulosic and algal biomass using a thermogravimetric and a fixed-bed reactor.

Science.gov (United States)

Yuan, Ting; Tahmasebi, Arash; Yu, Jianglong

2015-01-01

Pyrolysis characteristics of four algal and lignocellulosic biomass samples were studied by using a thermogravimetric analyzer (TGA) and a fixed-bed reactor. The effects of pyrolysis temperature and biomass type on the yield and composition of pyrolysis products were investigated. The average activation energy for pyrolysis of biomass samples by FWO and KAS methods in this study were in the range of 211.09-291.19kJ/mol. CO2 was the main gas component in the early stage of pyrolysis, whereas H2 and CH4 concentrations increased with increasing pyrolysis temperature. Bio-oil from Chlorellavulgaris showed higher content of nitrogen containing compounds compared to lignocellulosic biomass. The concentration of aromatic organic compounds such as phenol and its derivatives were increased with increasing pyrolysis temperature up to 700°C. FTIR analysis results showed that with increasing pyrolysis temperature, the concentration of OH, CH, CO, OCH3, and CO functional groups in char decreased sharply. Copyright © 2014 Elsevier Ltd. All rights reserved.

Thermogravimetric analyses and mineralogical study of polymer modified mortar with silica fume

Directory of Open Access Journals (Sweden)

Alessandra Etuko Feuzicana de Souza Almeida

2006-09-01

Full Text Available Mineral and organic additions are often used in mortars to improve their properties. Microstructural investigation concerning the effects of styrene acrylic polymer and silica fume on the mineralogical composition of high-early-strength portland cement pastes after 28 days of hydration are presented in this paper. Thermogravimetry and derivative thermogravimetry were used to study the interaction between polymers and cement, as well as the extent of pozzolanic reaction of the mortars with silica fume. Differential scanning calorimetry and X ray diffraction were used to investigate the cement hydration and the effect of the additions. The results showed that the addition of silica fume and polymer reduces the portlandite formation due to delaying of Portland cement hydration and pozzolanic reaction.

Thermogravimetric analysis and kinetic study of bamboo waste treated by Echinodontium taxodii using a modified three-parallel-reactions model.

Science.gov (United States)

Yu, Hongbo; Liu, Fang; Ke, Ming; Zhang, Xiaoyu

2015-06-01

In this study, the effect of pretreatment with Echinodontium taxodii on thermal decomposition characteristics and kinetics of bamboo wastes was investigated by thermogravimetric analysis. The results showed fungal pretreatment can enhance the thermal degradation of bamboo. The negative effect of extractives in bamboo on the thermal decomposition can be decreased by the pretreatment. A modified three-parallel-reactions model based on isolated lignin was firstly proposed to study pyrolysis kinetics of bamboo lignocellulose. Kinetic analysis showed that with increasing pretreatment time fungal delignification was enhanced to transform the lignin component with high activation energy into that with low activation energy and raise the cellulose content in bamboo, making the thermal decomposition easier. These results demonstrated fungal pretreatment provided a potential way to improve thermal conversion efficiency of bamboo. Copyright © 2015 Elsevier Ltd. All rights reserved.

Thermogravimetric analysis and TEM characterization of the oxidation and defect sites of carbon nanotubes synthesized by CVD of methane

International Nuclear Information System (INIS)

Li Haipeng; Zhao Naiqin; He Chunnian; Shi Chunsheng; Du Xiwen; Li Jiajun

2008-01-01

Changes in the thermogravimetrically determined oxidation behaviors of CVD-grown multi-walled carbon nanotubes (MWNTs) over Ni/Al catalyst with different Ni content were examined. Catalyst type was found to have a measurable impact upon nanotube stability, suggesting differing levels of crystalline perfection in the resulting nanotubes. With increasing the Ni content in the Ni/Al catalyst, the CNTs obtained became less stable during heat treatment in air. Furthermore, high-resolution transmission electron microscopy was employed to investigate the defect sites of as-grown MWNTs. The results provide evidence showing that defect sites along the walls and at the ends of the raw MWNTs facilitate the thermal oxidative destruction of the nanotubes

Combustion characteristics of Malaysian oil palm biomass, sub-bituminous coal and their respective blends via thermogravimetric analysis (TGA).

Science.gov (United States)

Idris, Siti Shawalliah; Rahman, Norazah Abd; Ismail, Khudzir

2012-11-01

The combustion characteristics of Malaysia oil palm biomass (palm kernel shell (PKS), palm mesocarp fibre (PMF) and empty fruit bunches (EFB)), sub-bituminous coal (Mukah Balingian) and coal/biomass blends via thermogravimetric analysis (TGA) were investigated. Six weight ratios of coal/biomass blends were prepared and oxidised under dynamic conditions from temperature 25 to 1100°C at four heating rates. The thermogravimetric analysis demonstrated that the EFB and PKS evolved additional peak besides drying, devolatilisation and char oxidation steps during combustion. Ignition and burn out temperatures of blends were improved in comparison to coal. No interactions were observed between the coal and biomass during combustion. The apparent activation energy during this process was evaluated using iso-conversional model free kinetics which resulted in highest activation energy during combustion of PKS followed by PMF, EFB and MB coal. Blending oil palm biomass with coal reduces the apparent activation energy value. Copyright © 2012 Elsevier Ltd. All rights reserved.

Thermogravimetric analysis for rapid assessment of moisture diffusivity in polydisperse powder and thin film matrices.

Science.gov (United States)

Thirunathan, Praveena; Arnz, Patrik; Husny, Joeska; Gianfrancesco, Alessandro; Perdana, Jimmy

2018-03-01

Accurate description of moisture diffusivity is key to precisely understand and predict moisture transfer behaviour in a matrix. Unfortunately, measuring moisture diffusivity is not trivial, especially at low moisture values and/or elevated temperatures. This paper presents a novel experimental procedure to accurately measure moisture diffusivity based on thermogravimetric approach. The procedure is capable to measure diffusivity even at elevated temperatures (>70°C) and low moisture values (>1%). Diffusivity was extracted from experimental data based on "regular regime approach". The approach was tailored to determine diffusivity from thin film and from poly-dispersed powdered samples. Subsequently, measured diffusivity was validated by comparing to available literature data, showing good agreement. Ability of this approach to accurately measure diffusivity at a wider range of temperatures provides better insight on temperature dependency of diffusivity. Thus, this approach can be crucial to ensure good accuracy of moisture transfer description/prediction especially when involving elevated temperatures. Copyright © 2017 Elsevier Ltd. All rights reserved.

Validating carbonation parameters of alkaline solid wastes via integrated thermal analyses: Principles and applications.

Science.gov (United States)

Pan, Shu-Yuan; Chang, E-E; Kim, Hyunook; Chen, Yi-Hung; Chiang, Pen-Chi

2016-04-15

Accelerated carbonation of alkaline solid wastes is an attractive method for CO2 capture and utilization. However, the evaluation criteria of CaCO3 content in solid wastes and the way to interpret thermal analysis profiles were found to be quite different among the literature. In this investigation, an integrated thermal analyses for determining carbonation parameters in basic oxygen furnace slag (BOFS) were proposed based on thermogravimetric (TG), derivative thermogravimetric (DTG), and differential scanning calorimetry (DSC) analyses. A modified method of TG-DTG interpretation was proposed by considering the consecutive weight loss of sample with 200-900°C because the decomposition of various hydrated compounds caused variances in estimates by using conventional methods of TG interpretation. Different quantities of reference CaCO3 standards, carbonated BOFS samples and synthetic CaCO3/BOFS mixtures were prepared for evaluating the data quality of the modified TG-DTG interpretation, in terms of precision and accuracy. The quantitative results of the modified TG-DTG method were also validated by DSC analysis. In addition, to confirm the TG-DTG results, the evolved gas analysis was performed by mass spectrometer and Fourier transform infrared spectroscopy for detection of the gaseous compounds released during heating. Furthermore, the decomposition kinetics and thermodynamics of CaCO3 in BOFS was evaluated using Arrhenius equation and Kissinger equation. The proposed integrated thermal analyses for determining CaCO3 content in alkaline wastes was precise and accurate, thereby enabling to effectively assess the CO2 capture capacity of alkaline wastes for mineral carbonation. Copyright © 2015 Elsevier B.V. All rights reserved.

Reaction of LiD with water vapor: thermogravimetric and scanning electron microscopy studies

International Nuclear Information System (INIS)

Balooch, M; Dinh, L N; LeMay, J D

2000-01-01

The kinetics of hydroxide film growth on LiD have been studied by the thermogravimetric method in nitrogen saturated with water vapor and by scanning electron microscopy (SEM) of samples that have been exposed to air with 50% relative humidity. The reaction probability is estimated to be 4 x 10 -7 for LiD exposed to ambient air with 50% relative humidity, suggesting that the diffusion through the hydroxide film is not the limiting step on the overall process at high moisture levels. The rate of growth is drastically reduced when the temperature is increased to 60 C

Thermogravimetric study and kinetic analysis of dried industrial sludge pyrolysis.

Science.gov (United States)

Liu, Guangrui; Song, Huijuan; Wu, Jinhu

2015-07-01

Thermogravimetric experiments of two different industrial sludge samples were carried out with non-isothermal temperature programs. The results indicated that the pyrolysis process contains three obvious stages and the main decomposition reaction occurred in the range of 200-600°C. The distributed activation energy model (DAEM) was also proposed describing equally well the pyrolysis behavior of the samples. The calculated activation energy was ranged from 170 to 593kJ/mol and 125 to 756kJ/mol for SLYG (sludge sample from chemical fiber factory) and SQD (sludge sample from woody industry), respectively. The reliability of this model not only provided good fit for all experiments, but also allowed accurate extrapolations to relative higher heating rates. Besides, the FTIR measurement was also used to further understand the relationship between pyrolysis behavior and chemical structures for industrial sludge. Copyright © 2015 Elsevier Ltd. All rights reserved.

Thermogravimetric Analysis and Kinetic Study on Pyrolysis of Veteri-narian Solid Waste

Directory of Open Access Journals (Sweden)

Andrés Felipe Rojas González

2016-10-01

Full Text Available Context: Institutional waste from clinical centers can be classified as those coming from health institutions dedicated to human attention and those coming from centers for animal veterinary care. The latter are mainly hazardous wastes, hence their disposal requires incineration. Most of such waste is organic, and it is possible, therefore, to take advantage of their energetic power in combustion or pyrolysis processes. This work is motivated because no literature was found on the pyrolysis kinetics veterinary waste, as this kind of studies are mainly focused on hospital waste of human health care. Method: The kinetics of pyrolysis is characterized and studied by means of thermogravimetric analysis of 6 major veterinary waste (gauze, cotton swabs, cotton, nails, hair, plastic syringes. The characterization is performed by proximate and elemental analysis, and thermogravimetric analysis. Reactivity characteristics and pyrolytic capability of wastes are established. The kinetics study on pyrolysis was carried out by determining the kinetic triplet by isoconversional Starink method. Results: It was established that the pyrolysis index increases with the heating rate and that the thermal degradation depends on the material type of the waste. Similarly, it was found that the temperature (ΔT = Tf - Ti for the thermal decomposition of veterinary waste is: ΔTnails> ΔThair > ΔTcotton swabs > ΔTgauze > ΔTcotton > ΔTplastic syringes; the activation energy is Enails> E hair > Eplastic syringes > Ecotton swabs > E gauze > Ecotton, and the reaction order is: n hair > nnails > ncotton swabs > ncotton > n gauze > n plastic syringes. Conclusions: These results suggest the possibility of using veterinary wastes for power generation, providing an alternative for sustainable energy development to cities in continuous growth, from both, energetic and environmental points of view.

Thermal degradation of Shredded Oil Palm Empty Fruit Bunches (SOPEFB) embedded with Cobalt catalyst by Thermogravimetric Analysis (TGA)

Science.gov (United States)

Alias, R.; Hamid, N. H.; Jaapar, J.; Musa, M.; Alwi, H.; Halim, K. H. Ku

2018-03-01

Thermal behavior and decomposition kinetics of shredded oil palm empty fruit bunches (SOPEFB) were investigated in this study by using thermogravimetric analysis (TGA). The SOPEFB were analyzed under conditions of temperature 30 °C to 900 °C with nitrogen gas flow at 50 ml/min. The SOPEFB were embedded with cobalt (II) nitrate solution with concentration 5%, 10%, 15% and 20%. The TG/DTG curves shows the degradation behavior of SOPEFB following with char production for each heating rate and each concentration of cobalt catalyst. Thermal degradation occurred in three phases, water drying phase, decomposition of hemicellulose and cellulose phase, and lignin decomposition phase. The kinetic equation with relevant parameters described the activation energy required for thermal degradation at the temperature regions of 200 °C to 350 °C. Activation energy (E) for different heating rate with SOPEFB embedded with different concentration of cobalt catalyst showing that the lowest E required was at SOPEFB with 20% concentration of cobalt catalyst..

Modified thermogravimetric apparatus to measure magnetic susceptibility on-line during annealing of metastable ferromagnetic materials

International Nuclear Information System (INIS)

Luciani, G.; Constantini, A.; Branda, F.; Ausanio, G.; Hison, C.; Iannotti, V.; Luponio, C.; Lanotte, L.

2004-01-01

The insertion of proper coils to generate a magnetic field, with controlled gradient, in a standard thermogravimetric apparatus is shown to be a valid solution to measure on-line, upon heat treatment, the magnetic susceptibility in ribbon shaped samples of a metastable ferromagnetic material. The method is very useful to individuate the annealing conditions that optimise soft or hard magnetic properties without using separate apparatuses for heat treatment, control of the structural phase transition and characterization of magnetic susceptibility

Friedel's salt profiles from thermogravimetric analysis and thermodynamic modelling of Portland cement-based mortars exposed to sodium chloride solution

DEFF Research Database (Denmark)

Shi, Zhenguo; Geiker, Mette Rica; Lothenbach, Barbara

2017-01-01

Thermogravimetric analysis (TGA), powder X-ray diffraction (XRD) and thermodynamic modelling have been used to obtain Friedel's salt profiles for saturated mortar cylinders exposed to a 2.8 M NaCl solution. Comparison of the measured Friedel's salt profiles with the total chloride profiles...

Thermogravimetric analysis of atomized ferromagnetic composites with multiwalled carbon nanotubes: an unusual behavior of nickel in nanospace.

Science.gov (United States)

Chen, Xu; Gupta, S; Santhanam, K S V

2014-03-01

A spin polarization of atomized ferromagnetic atoms like cobalt or nickel in nano space results in the modification of the electron configuration in the ferromagnetic atom that changes its oxidative property. We have prepared cobalt and nickel composites with multiwalled carbon nanotubes using atomized cobalt and nickel particles, for investigating their thermal oxidative behavior by thermogravimetric analysis (TGA). The composites showed the absence of a thermal oxidation in the temperature range of ambient to the break down temperature of multiwalled carbon nanotubes at 800 degrees C. At this temperature while Co composite forms cobalt oxide, the Ni composite becomes volatile that results in the divergent behavior of the two ferromagnetic compounds with a weight gain observed in TGA for Co and a loss for Ni. The mechanisms operating in the two cases are discussed in this work.

Thermogravimetric analysis of silicon carbide-silicon nitride polycarbosilazane precursor during pyrolysis from ambient to 1000 C

Science.gov (United States)

Ledbetter, F. E., III; Daniels, J. G.; Clemons, J. M.; Hundley, N. H.; Penn, B. G.

1984-01-01

Thermogravimetric analysis data are presented on the unmeltable polycarbosilazane precursor of silicon carbide-silicon nitride fibers, over the room temperature-1000 C range in a nitrogen atmosphere, in order to establish the weight loss at various temperatures during the precursor's pyrolysis to the fiber material. The fibers obtained by this method are excellent candidates for use in applications where the oxidation of carbon fibers (above 400 C) renders them unsuitable.

Morphological Changes of Limestone Sorbent Particles during Carbonation/Calcination Looping Cycles in a Thermogravimetric Analyzer (TGA) and Reactivation with Steam

KAUST Repository

Wu, Y.; Blamey, J.; Anthony, E. J.; Fennell, P. S.

2010-01-01

Carbonation and calcination looping cycles were carried out on four limestones in a thermogravimetric analyzer (TGA). The CO2 carrying capacity of a limestone particle decays very quickly in the first 10 cycles, reducing to about 20% of its original

Preparation and thermogravimetric study of some uranyl phosphates

International Nuclear Information System (INIS)

Schaekers, J.M.

1970-10-01

The preparation of uranyl ammonium phosphate trihydrate (UAP = UO 2 NH 4 PO 4 .3H 2 O), acid uranyl phosphate tetrahydrate(AUP = UO 2 HPO 4 .4H 2 O) and neutral uranyl phosphate tetrahydrate (NUPT = (UO 2 ) 3 (PO 4 ) 2 .4H 2 O) was investigated during the data from the literature. The thermal decomposition in different atmospheres, such as air, oxygen, nitrogen and argon, was studied in the temperature range 25-1000 0 C. It was found that the pyrophosphate U 2 O 3 P 2 O 7 is a stable decomposition product of UAP as well as of AUP. A mixture of U 3 O 8 and U 2 O 3 P 2 O 7 is obtained when the NUPT is decomposed in an oxygen-free atmosphere. NUPT however is stable in an oxidising atmosphere. Hydrogen and carbon reductions were also carried out, and UO 2 or (UO) 2 P 2 O 7 as well as mixtures of these two products can be obtained, depending on the starting material and the reduction temperature. The different reduction and decomposition reactions were studied by means of thermogravimetric analysis, and activation energies were calculated where possible. I.R. spectral analysis was also used to identify various products with the same composition [af

Uncertainty Determination Methodology, Sampling Maps Generation and Trend Studies with Biomass Thermogravimetric Analysis

Science.gov (United States)

Pazó, Jose A.; Granada, Enrique; Saavedra, Ángeles; Eguía, Pablo; Collazo, Joaquín

2010-01-01

This paper investigates a method for the determination of the maximum sampling error and confidence intervals of thermal properties obtained from thermogravimetric analysis (TG analysis) for several lignocellulosic materials (ground olive stone, almond shell, pine pellets and oak pellets), completing previous work of the same authors. A comparison has been made between results of TG analysis and prompt analysis. Levels of uncertainty and errors were obtained, demonstrating that properties evaluated by TG analysis were representative of the overall fuel composition, and no correlation between prompt and TG analysis exists. Additionally, a study of trends and time correlations is indicated. These results are particularly interesting for biomass energy applications. PMID:21152292

Modelization of nanospace interaction involving a ferromagnetic atom: a spin polarization effect study by thermogravimetric analysis.

Science.gov (United States)

Santhanam, K S V; Chen, Xu; Gupta, S

2014-04-01

Ab initio studies of ferromagnetic atom interacting with carbon nanotubes have been reported in the literature that predict when the interaction is strong, a higher hybridization with confinement effect will result in spin polarization in the ferromagnetic atom. The spin polarization effect on the thermal oxidation to form its oxide is modeled here for the ferromagnetic atom and its alloy, as the above studies predict the 4s electrons are polarized in the atom. The four models developed here provide a pathway for distinguishing the type of interaction that exists in the real system. The extent of spin polarization in the ferromagnetic atom has been examined by varying the amount of carbon nanotubes in the composites in the thermogravimetric experiments. In this study we report the experimental results on the CoNi alloy which appears to show selective spin polarization. The products of the thermal oxidation has been analyzed by Fourier Transform Infrared Spectroscopy.

Thermogravimetric characteristics of typical municipal solid waste fractions during co-pyrolysis.

Science.gov (United States)

Zhou, Hui; Long, YanQiu; Meng, AiHong; Li, QingHai; Zhang, YanGuo

2015-04-01

The interactions of nine typical municipal solid waste (MSW) fractions during pyrolysis were investigated using the thermogravimetric analyzer (TGA). To compare the mixture results with the calculation results of superposition of single fractions quantitatively, TG overlap ratio was introduced. There were strong interactions between orange peel and rice (overlap ratio 0.9736), and rice and poplar wood (overlap ratio 0.9774). The interactions of mixture experiments postponed the peak and lowered the peak value. Intense interactions between PVC and rice, poplar wood, tissue paper, wool, terylene, and rubber powder during co-pyrolysis were observed, and the pyrolysis at low temperature was usually promoted. The residue yield was increased when PVC was blended with rice, poplar wood, tissue paper, or rubber powder; while the residue yield was decreased when PVC was blended with wool. Copyright © 2014 Elsevier Ltd. All rights reserved.

Nonisothermal Thermogravimetric Analysis of Thai Lignite with High CaO Content

Science.gov (United States)

Pintana, Pakamon

2013-01-01

Thermal behaviors and combustion kinetics of Thai lignite with different SO3-free CaO contents were investigated. Nonisothermal thermogravimetric method was carried out under oxygen environment at heating rates of 10, 30, and 50°C min−1 from ambient up to 1300°C. Flynn-Wall-Ozawa (FWO) and Kissinger-Akahira-Sunose (KAS) methods were adopted to estimate the apparent activation energy (E) for the thermal decomposition of these coals. Different thermal degradation behaviors were observed in lignites with low (14%) and high (42%) CaO content. Activation energy of the lignite combustion was found to vary with the conversion fraction. In comparison with the KAS method, higher E values were obtained by the FWO method for all conversions considered. High CaO lignite was observed to have higher activation energy than the low CaO coal. PMID:24250259

A vacuum thermogravimetric method for outgassing evaluations of silicone-coated fiberglass cloth

Science.gov (United States)

Jensen, L. B.; Mccauley, G. B.; Honma, M.; Hultquist, A. E.

1972-01-01

A method for evaluating outgassing characteristics of space-sensitive materials was devised by modifying a thermogravimetric balance so that a continual weight loss trace is obtained as a function of time at constant temperature and nearly constant pressure. In addition the apparatus is capable of collecting room temperature condensibles during the outgassing run. A series of silicone-coated glass cloth samples were evaluated by this method. The major advantage of the technique is that data presentation is developed in the form of a continuous trace. This data can then be utilized to develop the kinetics of weight loss. The technique has been shown to be a useful and valid one for indicating small differences between materials under vacuum and elevated temperature conditions.

Splitting CO2 with a ceria‐based redox cycle in a solar‐driven thermogravimetric analyzer

Science.gov (United States)

Takacs, M.; Ackermann, S.; Bonk, A.; Neises‐von Puttkamer, M.; Haueter, Ph.; Scheffe, J. R.; Vogt, U. F.

2016-01-01

Thermochemical splitting of CO2 via a ceria‐based redox cycle was performed in a solar‐driven thermogravimetric analyzer. Overall reaction rates, including heat and mass transport, were determined under concentrated irradiation mimicking realistic operation of solar reactors. Reticulated porous ceramic (RPC) structures and fibers made of undoped and Zr4+‐doped CeO2, were endothermally reduced under radiative fluxes of 1280 suns in the temperature range 1200–1950 K and subsequently re‐oxidized with CO2 at 950–1400 K. Rapid and uniform heating was observed for 8 ppi ceria RPC with mm‐sized porosity due to its low optical thickness and volumetric radiative absorption, while ceria fibers with μm‐sized porosity performed poorly due to its opacity to incident irradiation. The 10 ppi RPC exhibited higher fuel yield because of its higher sample density. Zr4+‐doped ceria showed increasing reduction extents with dopant concentration but decreasing specific CO yield due to unfavorable oxidation thermodynamics and slower kinetics. © 2016 American Institute of Chemical Engineers AIChE J, 63: 1263–1271, 2017 PMID:28405030

Pyrolysis and oxy-fuel combustion characteristics and kinetics of petrochemical wastewater sludge using thermogravimetric analysis.

Science.gov (United States)

Chen, Jianbiao; Mu, Lin; Cai, Jingcheng; Yao, Pikai; Song, Xigeng; Yin, Hongchao; Li, Aimin

2015-12-01

The pyrolysis and oxy-fuel combustion characteristics of petrochemical wastewater sludge (PS) were studied in air (O2/N2) and oxy-fuel (O2/CO2) atmospheres using non-isothermal thermogravimetric analysis (TGA). Pyrolysis experiments showed that the weight loss profiles were almost similar up to 1050K in both N2 and CO2 atmospheres, while further weight loss took place in CO2 atmosphere at higher temperatures due to char-CO2 gasification. Compared with 20%O2/80%N2, the drying and devolatilization stage of PS were delayed in 20%O2/80%CO2 due to the differences in properties of the diluting gases. In oxy-fuel combustion experiments, with O2 concentration increasing, characteristic temperatures decreased, while characteristic combustion rates and combustion performance indexes increased. Kinetic analysis of PS decomposition under various atmospheres was performed using Coats-Redfern approach. The results indicated that, with O2 concentration increasing, the activation energies of Step 1 almost kept constant, while the values of subsequent three steps increased. Copyright © 2015 Elsevier Ltd. All rights reserved.

Splitting CO2 with a ceria-based redox cycle in a solar-driven thermogravimetric analyzer.

Science.gov (United States)

Takacs, M; Ackermann, S; Bonk, A; Neises-von Puttkamer, M; Haueter, Ph; Scheffe, J R; Vogt, U F; Steinfeld, A

2017-04-01

Thermochemical splitting of CO 2 via a ceria-based redox cycle was performed in a solar-driven thermogravimetric analyzer. Overall reaction rates, including heat and mass transport, were determined under concentrated irradiation mimicking realistic operation of solar reactors. Reticulated porous ceramic (RPC) structures and fibers made of undoped and Zr 4+ -doped CeO 2 , were endothermally reduced under radiative fluxes of 1280 suns in the temperature range 1200-1950 K and subsequently re-oxidized with CO 2 at 950-1400 K. Rapid and uniform heating was observed for 8 ppi ceria RPC with mm-sized porosity due to its low optical thickness and volumetric radiative absorption, while ceria fibers with μm-sized porosity performed poorly due to its opacity to incident irradiation. The 10 ppi RPC exhibited higher fuel yield because of its higher sample density. Zr 4+ -doped ceria showed increasing reduction extents with dopant concentration but decreasing specific CO yield due to unfavorable oxidation thermodynamics and slower kinetics. © 2016 American Institute of Chemical Engineers , 63: 1263-1271, 2017.

Thermogravimetric analysis of phase transitions in cement compositions mixed by sodium silicate solution

Directory of Open Access Journals (Sweden)

Fedosov Sergey Viktorovich

2014-01-01

Full Text Available This paper presents a study of the capability to modify cement by mechanical activation of sodium silicate water solution. Admixtures or blends of binding agents were employed for modifying concrete properties. The liquid glass is applied to protect from chemically or physically unfavorable environmental impacts, such as acidic medium and high temperature. The sodium silicate is a high-capacity setting accelerator. The increasing of the liquid glass proportion in the mix leads to the degradation of the cement paste plasticity and for this reason it is necessary to reduce the amount of liquid glass in the cement paste. The activation of dilute water solution of sodium silicate into rotary pulsating apparatus directly before tempering of the cement paste is an effective way to decrease mass fraction of liquid glass in the cement paste. The results of the combined influence of liquid glass and mechanical activation on physicochemical processes taking place in cement stone are represented in this research. Thermogravimetric analysis was used in order to study cement blends. Thermogravimetric analysis of modified cement stone assays was performed by thermo analyzer SETARAM TGA 92-24. The results of the analysis of phase transition taking place under high-temperature heating of cement stone modified by the mechanical activation of the water solution of the sodium silicate were introduced. Thermograms of cement stone assays were obtained at different hardening age. The comparison of these thermograms allows us to come to a conclusion on the formation and the retention during long time of a more dense structure of the composite matrix mixed by the mechanical activation of sodium silicate water solution. The relation between the concrete composition and its strength properties was stated. Perhaps, the capability of modified concrete to keep calcium ions in sparingly soluble hydrosilicates leads to the increase in its durability and corrosion resistance.

Thermogravimetric study of the pyrolysis of biomass residues from tomato processing industry

Energy Technology Data Exchange (ETDEWEB)

Mangut, V.; Sabio, E.; Ganan, J.; Gonzalez, J.F.; Ramiro, A.; Gonzalez, C.M.; Roman, S.; Al-Kassir, A. [Department of Chemical and Energy Engineering, University of Extremadura, Avda. de Elvas s/n, 06071 Badajoz (Spain)

2006-01-15

There is an increasing concern with the environmental problems associated with the increasing CO{sub 2}, NO{sub x} and SO{sub x} emissions resulting from the rising use of fossil fuels. Renewable energy, mainly biomass, can contribute to reduce the fossil fuels consumption. Biomass is a renewable resource with a widespread world distribution. Tomato processing industry produces a high amount of biomass residue (peel and seeds) that could be used for thermal energy and electricity. A characterization and thermogravimetric study has been carried out. The residue has a high HHV and volatile content, and a low ash, and S contents. A kinetic model has been developed based on the degradation of hemicellulose, cellulose, lignin and oil that describe the pyrolysis of peel, seeds and peel and seeds residues. (author)

Pyrolysis characteristics and kinetics of aquatic biomass using thermogravimetric analyzer.

Science.gov (United States)

Wu, Kejing; Liu, Ji; Wu, Yulong; Chen, Yu; Li, Qinghai; Xiao, Xin; Yang, Mingde

2014-07-01

The differences in pyrolysis process of three species of aquatic biomass (microalgae, macroalgae and duckweed) were investigated by thermogravimetric analysis (TGA). Three stages were observed during the pyrolysis process and the main decomposition stage could be divided further into three zones. The pyrolysis characteristics of various biomasses were different at each zone, which could be attributed to the differences in their components. A stepwise procedure based on iso-conversional and master-plots methods was used for the kinetic and mechanism analysis of the main decomposition stage. The calculation results based on the kinetic model was in good agreement with the experimental data of weight loss, and each biomass had an increasing activation energy of 118.35-156.13 kJ/mol, 171.85-186.46 kJ/mol and 258.51-268.71 kJ/mol in zone 1, 2 and 3, respectively. This study compares the pyrolysis behavior of various aquatic biomasses and provides basis for further applications of the biomass thermochemical conversion. Copyright © 2014. Published by Elsevier Ltd.

Effect of anaerobic digestion on sequential pyrolysis kinetics of organic solid wastes using thermogravimetric analysis and distributed activation energy model.

Science.gov (United States)

Li, Xiaowei; Mei, Qingqing; Dai, Xiaohu; Ding, Guoji

2017-03-01

Thermogravimetric analysis, Gaussian-fit-peak model (GFPM), and distributed activation energy model (DAEM) were firstly used to explore the effect of anaerobic digestion on sequential pyrolysis kinetic of four organic solid wastes (OSW). Results showed that the OSW weight loss mainly occurred in the second pyrolysis stage relating to organic matter decomposition. Compared with raw substrate, the weight loss of corresponding digestate was lower in the range of 180-550°C, but was higher in 550-900°C. GFPM analysis revealed that organic components volatized at peak temperatures of 188-263, 373-401 and 420-462°C had a faster degradation rate than those at 274-327°C during anaerobic digestion. DAEM analysis showed that anaerobic digestion had discrepant effects on activation energy for four OSW pyrolysis, possibly because of their different organic composition. It requires further investigation for the special organic matter, i.e., protein-like and carbohydrate-like groups, to confirm the assumption. Copyright © 2016 Elsevier Ltd. All rights reserved.

Thermogravimetric study of the kinetics of lithium titanate reduction by hydrogen

International Nuclear Information System (INIS)

Sonak, Sagar; Rakesh, R.; Jain, Uttam; Mukherjee, Abhishek; Kumar, Sanjay; Krishnamurthy, Nagaiyar

2014-01-01

Highlights: • Li 2 TiO 3 powder is synthesized by the gel combustion route. • Activation energy of reduction of Li 2 TiO 3 by H 2 found out to be 27.45 kJ/mol H 2 . • Non-stoichiometric phase of Li 2 TiO 3 is formed in hydrogen atmosphere. • One-dimensional diffusion appears to be the most probable mechanism of reduction. - Abstract: The lithium titanate powder was synthesized by gel-combustion route. The mechanism and the kinetics of hydrogen interaction with lithium titanate powder were studied using non-isothermal thermogravimetric technique. Lithium titanate underwent reduction in hydrogen atmosphere which led to the formation of oxygen deficient non-stoichiometric compound in lithium titanate. One-dimensional diffusion appeared to be the most probable reaction mechanism. The activation energy for reduction of lithium titanate under hydrogen atmosphere was found to be 27.4 kJ/mol/K. Structural changes after hydrogen reduction in lithium titanate were observed in X-ray diffraction analysis

Physicotechnical, spectroscopic and thermogravimetric properties of powdered cellulose and microcrystalline cellulose derived from groundnut shells

Directory of Open Access Journals (Sweden)

Chukwuemeka P. Azubuike

2012-09-01

Full Text Available α-Cellulose and microcrystalline cellulose powders, derived from agricultural waste products, that have for the pharmaceutical industry, desirable physical (flow properties were investigated. α–Cellulose (GCN was extracted from groundnut shell (an agricultural waste product using a non-dissolving method based on inorganic reagents. Modification of this α -cellulose was carried out by partially hydrolysing it with 2N hydrochloric acid under reflux to obtain microcrystalline cellulose (MCGN. The physical, spectroscopic and thermal properties of the derived α-cellulose and microcrystalline cellulose powders were compared with Avicel® PH 101, a commercial brand of microcrystalline cellulose (MCCA, using standard methods. X-ray diffraction and infrared spectroscopy analysis showed that the α-cellulose had lower crystallinity. This suggested that treatment with 2N hydrochloric acid led to an increase in the crystallinity index. Thermogravimetric analysis showed quite similar thermal behavior for all cellulose samples, although the α-cellulose had a somewhat lower stability. A comparison of the physical properties between the microcrystalline celluloses and the α-cellulose suggests that microcrystalline cellulose (MCGN and MCCA might have better flow properties. In almost all cases, MCGN and MCCA had similar characteristics. Since groundnut shells are agricultural waste products, its utilization as a source of microcrystalline cellulose might be a good low-cost alternative to the more expensive commercial brand.

Thermogravimetric analysis of the behavior of sub-bituminous coal and cellulosic ethanol residue during co-combustion.

Science.gov (United States)

Buratti, C; Barbanera, M; Bartocci, P; Fantozzi, F

2015-06-01

The influence of the addition of cellulosic ethanol residue (CER) on the combustion of Indonesian sub-bituminous coal was analyzed by non isothermal thermo-gravimetric analysis (TGA). The effect of blends ratio (5%, 10%, 15% and 20%), interaction mechanism, and heating rate (5°C/min, 10°C/min, 15°C/min, 20°C/min) on the combustion process was studied. The results show that the increase of the blending ratio allows to achieve the increase of the combustibility index from 7.49E-08 to 5.26E-07 at the blending ratio of 20%. Two types of non-isothermal kinetic analysis methods (Ozawa-Flynn-Wall and Vyazovkin) were also applied. Results indicate that the activation energy of the blends decreases with increasing the conversion rate. In particular, the blending ratio of 20% confirms to have the better combustion performance, with the average value of the activation energy equal to 41.10 kJ/mol obtained by Ozawa-Flynn-Wall model and 31.17 kJ/mol obtained by Vyazovkin model. Copyright © 2015 Elsevier Ltd. All rights reserved.

Validating carbonation parameters of alkaline solid wastes via integrated thermal analyses: Principles and applications

International Nuclear Information System (INIS)

Pan, Shu-Yuan; Chang, E.-E.; Kim, Hyunook; Chen, Yi-Hung; Chiang, Pen-Chi

2016-01-01

Highlights: • Key carbonation parameters of wastes are determined by integrated thermal analyses. • A modified TG-DTG interpretation is proposed, and validated by the DSC technique. • The modified TG-DTG interpretation is further verified by DTA, TG-MS and TG-FTIR. • Kinetics and thermodynamics of CaCO 3 decomposition in solid wastes are determined. • Implication to maximum carbonation conversion of various solid wastes is described. - Abstract: Accelerated carbonation of alkaline solid wastes is an attractive method for CO 2 capture and utilization. However, the evaluation criteria of CaCO 3 content in solid wastes and the way to interpret thermal analysis profiles were found to be quite different among the literature. In this investigation, an integrated thermal analyses for determining carbonation parameters in basic oxygen furnace slag (BOFS) were proposed based on thermogravimetric (TG), derivative thermogravimetric (DTG), and differential scanning calorimetry (DSC) analyses. A modified method of TG-DTG interpretation was proposed by considering the consecutive weight loss of sample with 200–900 °C because the decomposition of various hydrated compounds caused variances in estimates by using conventional methods of TG interpretation. Different quantities of reference CaCO 3 standards, carbonated BOFS samples and synthetic CaCO 3 /BOFS mixtures were prepared for evaluating the data quality of the modified TG-DTG interpretation, in terms of precision and accuracy. The quantitative results of the modified TG-DTG method were also validated by DSC analysis. In addition, to confirm the TG-DTG results, the evolved gas analysis was performed by mass spectrometer and Fourier transform infrared spectroscopy for detection of the gaseous compounds released during heating. Furthermore, the decomposition kinetics and thermodynamics of CaCO 3 in BOFS was evaluated using Arrhenius equation and Kissinger equation. The proposed integrated thermal analyses for

Validating carbonation parameters of alkaline solid wastes via integrated thermal analyses: Principles and applications

Energy Technology Data Exchange (ETDEWEB)

Pan, Shu-Yuan [Graduate Institute of Environmental Engineering, National Taiwan University, Taipei 10673, Taiwan (China); Chang, E.-E. [Department of Biochemistry, Taipei Medical University, Taipei 110, Taiwan (China); Kim, Hyunook [Department of Environmental Engineering, University of Seoul, Seoul 130-743 (Korea, Republic of); Chen, Yi-Hung [Department of Chemical Engineering and Biotechnology, National Taipei University of Technology, Taipei 10608, Taiwan (China); Chiang, Pen-Chi, E-mail: pcchiang@ntu.edu.tw [Graduate Institute of Environmental Engineering, National Taiwan University, Taipei 10673, Taiwan (China)

2016-04-15

Highlights: • Key carbonation parameters of wastes are determined by integrated thermal analyses. • A modified TG-DTG interpretation is proposed, and validated by the DSC technique. • The modified TG-DTG interpretation is further verified by DTA, TG-MS and TG-FTIR. • Kinetics and thermodynamics of CaCO{sub 3} decomposition in solid wastes are determined. • Implication to maximum carbonation conversion of various solid wastes is described. - Abstract: Accelerated carbonation of alkaline solid wastes is an attractive method for CO{sub 2} capture and utilization. However, the evaluation criteria of CaCO{sub 3} content in solid wastes and the way to interpret thermal analysis profiles were found to be quite different among the literature. In this investigation, an integrated thermal analyses for determining carbonation parameters in basic oxygen furnace slag (BOFS) were proposed based on thermogravimetric (TG), derivative thermogravimetric (DTG), and differential scanning calorimetry (DSC) analyses. A modified method of TG-DTG interpretation was proposed by considering the consecutive weight loss of sample with 200–900 °C because the decomposition of various hydrated compounds caused variances in estimates by using conventional methods of TG interpretation. Different quantities of reference CaCO{sub 3} standards, carbonated BOFS samples and synthetic CaCO{sub 3}/BOFS mixtures were prepared for evaluating the data quality of the modified TG-DTG interpretation, in terms of precision and accuracy. The quantitative results of the modified TG-DTG method were also validated by DSC analysis. In addition, to confirm the TG-DTG results, the evolved gas analysis was performed by mass spectrometer and Fourier transform infrared spectroscopy for detection of the gaseous compounds released during heating. Furthermore, the decomposition kinetics and thermodynamics of CaCO{sub 3} in BOFS was evaluated using Arrhenius equation and Kissinger equation. The proposed

Thermogravimetric analysis of the co-combustion of paper mill sludge and municipal solid waste

International Nuclear Information System (INIS)

Hu, Shanchao; Ma, Xiaoqian; Lin, Yousheng; Yu, Zhaosheng; Fang, Shiwen

2015-01-01

Highlights: • Thermogravimetric analysis of paper mill sludge and municipal solid waste were studied. • The combustion of paper mill sludge could be improved by blending municipal solid waste. • There existed significant interaction during co-combustion of the blends. • The OFW and Starink methods were used to obtain the activation energy. • The average activation energy was the lowest by blending 20% municipal solid waste. - Abstract: The thermal characteristics and kinetics of paper mill sludge (PMS), municipal solid waste (MSW) and their blends in the combustion process were investigated in this study. The mass percentages of PMS in the blends were 10%, 30%, 50%, 70% and 90%, respectively. The experiments were carried out at different heating rates (10 °C/min, 20 °C/min and 30 °C/min) and the temperature ranged from room temperature to 1000 °C in a thermogravimetric simultaneous thermal analyzer. The results suggested that the ignition temperature and burnout temperature of MSW were lower than that of PMS, and the mass loss rate of MSW was larger especially at low temperatures. There were only two mass loss peaks in the differential thermogravimetry (DTG) curve, while three mass loss peaks were observed when the blending ratios of PMS were 30%, 50%, 70%. The value of the comprehensive combustion characteristic index of the blends indicated a good combustibility when the percentage of PMS (PPMS) in the blends was less than 30%. There existed certain interaction between the combustion process of PMS and MSW, especially at high temperature stage. Activation energy (E) value obtained by the Ozawa–Flynn–Wall (OFW) method and the Starink method were very consistent. When the mass percentage of PMS in the blends was 80%, the E average value attained the minimum

Kinetic analysis of thermogravimetric data of thorium-all-cis-1,2,3,4-cyclopentanetetracarboxylic acid complex

International Nuclear Information System (INIS)

Ramarao, G.A.; Nair, P.K.R.; Srinivasulu, K.

1979-01-01

Thorium (IV) forms 1:1 complex with all-cis-1,2,3,4-cyclopentanetetracarboxylic acid (CPTA). Thermogravimetric analysis indicated that it undergoes primarily a two step decomposition of one corresponding to loss of water and another to the decomposition of the complex. Apparent activation energy, frequency factor and activation entropy were determined. Using the experimental data, the reaction order and activation energy were calculated by Freeman-Carroll method and also by Doyle method as modified by J. Zsako, by calculation of standard deviation instead of curve fitting method. (author)

Fluid selection and parametric analysis on condensation temperature and plant height for a thermogravimetric heat pump

International Nuclear Information System (INIS)

Najafi, Behzad; Obando Vega, Pedro; Guilizzoni, Manfredo; Rinaldi, Fabio; Arosio, Sergio

2015-01-01

The Thermogravimetric Heat Pump (TGHP) is a non-conventional system, implementing a reverse cycle, the main difference of which from the usual vapor compression (Rankine) cycle is a quasi-isothermal compression of the working fluid by a high heat capacity carrier fluid. Previous studies showed that employing HFC134a or PF5050 as working fluids may be promising in terms of thermodynamic performance, though the corresponding required plant heights confine its application to tall buildings (from minimum height of 10–12 storeys to skyscrapers). Accordingly, an investigation has been carried out in the present study in order to determine a group of fluids which allow lower heights under the same input conditions. In order to investigate the performance of the system and the required plant height, operation of a 100 kW TGHP has been simulated for 17 different fluids. Accordingly, the corresponding COPs and required heights are determined and based on the achieved COPs, the optimum fluid for each range of building height is selected. The resulting plant heights range from 20 m to nearly 200 m and R245ca is shown to be the most promising fluid for the lowest plant height range. A parametric study is next carried out in order to study the effect of variations in the condensation temperature and the dimensionless plant height on the performance of the system. The obtained results demonstrate that an increase in the former from 313 K to 348 K, for almost all of the analyzed fluids, causes a reduction of around 50% in the COP. It is also shown that, almost independent of the employed fluid, the maximum values of COP are reached for a dimensionless plant height of around 1.8. Moreover, all the analyzed fluids show basically the same COP trend and, at the same operating conditions, the COP values for all fluids are within a 10% range of variation. This leads to the conclusion that the thermophysical properties of the employed fluid mainly influences the required height of

Effect of organic calcium compounds on combustion characteristics of rice husk, sewage sludge, and bituminous coal: thermogravimetric investigation.

Science.gov (United States)

Zhang, Lihui; Duan, Feng; Huang, Yaji

2015-04-01

Experiments were conducted in a thermogravimetric analyzer to assess the enhancement of combustion characteristics of different solid fuels blended with organic calcium compounds (OCCs). Rice husk, sewage sludge, and bituminous coal, and two OCC were used in this study. Effect of different mole ratios of calcium to sulfur (Ca/S ratio) on the combustion characteristics were also investigated. Results indicated that combustion performance indexes for bituminous coal impregnated by OCC were improved, however, an inverse trend was found for sewage sludge because sewage sludge has lower ignition temperature and higher volatile matter content compared to those of OCC. For rice husk, effect of added OCC on the combustion characteristics is not obvious. Different solid fuels show different combustion characteristics with increases of Ca/S ratio. The maximum combustion performance indexes appear at Ca/S ratios of 1:1, 2:1, and 3:1 for OCC blended with Shenhua coal, rice husk, and sewage sludge, respectively. Copyright © 2015 Elsevier Ltd. All rights reserved.

Thermogravimetric control of intermediate compounds in uranium metallurgy; Control termogravimetrico de productos intermedios de la metalurgia del uranio

Energy Technology Data Exchange (ETDEWEB)

Gasco Sanchez, L; Fernandez Cellini, R

1959-07-01

The thermal decomposition of some intermediate compounds in the metallurgy of the uranium as uranium peroxide, ammonium uranate, uranium and ammonium penta-fluoride, uranium tetrafluoride and uranous oxide has been study by means of the Chevenard's thermo balance. Some data on pyrolysis of synthetic mixtures of intermediate compounds which may occasionally appear during the industrial process, are given. Thermogravimetric methods of control are suggested, usable in interesting products in the uranium metallurgy. (Author) 20 refs.

Thermogravimetric kinetic model of the pyrolysis and combustion of an ethylene-vinyl acetate copolymer refuse

Energy Technology Data Exchange (ETDEWEB)

Angela N. Garcia; Rafael Font [Universidad de Alicante, Alicante (Spain). Faculty of Sciences

2004-06-01

A kinetic study of the pyrolysis as well as the combustion of EVA copolymer refuse originating from the footwear industry was carried out by thermogravimetric analysis. Different runs were performed at heating rates between 5-20{sup o}C min{sup -1} and atmospheres with different percentages of oxygen: 0, 10 and 20% (v/v). Pyrolysis and combustion processes can be simulated by two series reactions. The results obtained indicate that the second reaction begins when the first one is almost finished which implies that a good correlation is also obtained by simulation of the thermal decomposition of two independent fractions. 32 refs., 4 figs., 3 tabs.

Biomass pyrolysis and combustion integral and differential reaction heats with temperatures using thermogravimetric analysis/differential scanning calorimetry.

Science.gov (United States)

Shen, Jiacheng; Igathinathane, C; Yu, Manlu; Pothula, Anand Kumar

2015-06-01

Integral reaction heats of switchgrass, big bluestem, and corn stalks were determined using thermogravimetric analysis/differential scanning calorimetry (TGA/DSC). Iso-conversion differential reaction heats using TGA/DSC pyrolysis and combustion of biomass were not available, despite reports available on heats required and released. A concept of iso-conversion differential reaction heats was used to determine the differential reaction heats of each thermal characteristics segment of these materials. Results showed that the integral reaction heats were endothermic from 30 to 700°C for pyrolysis of switchgrass and big bluestem, but they were exothermic for corn stalks prior to 587°C. However, the integral reaction heats for combustion of the materials followed an endothermic to exothermic transition. The differential reaction heats of switchgrass pyrolysis were predominantly endothermic in the fraction of mass loss (0.0536-0.975), and were exothermic for corn stalks (0.0885-0.850) and big bluestem (0.736-0.919). Study results provided better insight into biomass thermal mechanism. Published by Elsevier Ltd.

Acoustic emission analysis coupled with thermogravimetric experiments dedicated to high temperature corrosion studies on metallic alloys

International Nuclear Information System (INIS)

Serris, Eric; Al Haj, Omar; Peres, Veronique; Cournil, Michel; Kittel, Jean; Grosjean, Francois; Ropital, Francois

2014-01-01

High temperature corrosion of metallic alloys (like iron, nickel, zirconium alloys) can damage equipment of many industrial fields (refinery, petrochemical, nuclear..). Acoustic emission (AE) is an interesting method owing to its sensitivity and its non-destructive aspect to quantify the level of damage in use of these alloys under various environmental conditions. High temperature corrosive phenomena create stresses in the materials; the relaxation by cracks of these stresses can be recorded and analyzed using the AE system. The goal of our study is to establish an acoustic signals database which assigns the acoustic signals to the specific corrosion phenomena. For this purpose, thermogravimetric analysis (TGA) is coupled with acoustic emission (AE) devices. The oxidation of a zirconium alloy, zircaloy-4, is first studied using thermogravimetric experiment coupled to acoustic emission analysis at 900 C. An inward zirconium oxide scale, preliminary dense, then porous, grow during the isothermal isobaric step. The kinetic rate increases significantly after a kinetic transition (breakaway). This acceleration occurs with an increase of acoustic emission activity. Most of the acoustic emission bursts are recorded after the kinetic transition. Acoustic emission signals are also observed during the cooling of the sample. AE numerical treatments (using wavelet transform) completed by SEM microscopy characterizations allows us to distinguish the different populations of cracks. Metal dusting represents also a severe form of corrosive degradation of metal alloy. Iron metal dusting corrosion is studied by AE coupled with TGA at 650 C under C 4 H 10 + H 2 + He atmosphere. Acoustic emission signals are detected after a significant increase of the sample mass.

Thermogravimetric control of intermediate compounds in uranium metallurgy; Control termogravimetrico de productos intermedios de la metalurgia del uranio

Energy Technology Data Exchange (ETDEWEB)

Gasco Sanchez, L.; Fernandez Cellini, R.

1959-07-01

The thermal decomposition of some intermediate compounds in the metallurgy of the uranium as uranium peroxide, ammonium uranate, uranium and ammonium penta-fluoride, uranium tetrafluoride and uranous oxide has been study by means of the Chevenard's thermo balance. Some data on pyrolysis of synthetic mixtures of intermediate compounds which may occasionally appear during the industrial process, are given. Thermogravimetric methods of control are suggested, usable in interesting products in the uranium metallurgy. (Author) 20 refs.

Theoretical (in B3LYP/6-3111++G** level), spectroscopic (FT-IR, FT-Raman) and thermogravimetric studies of gentisic acid and sodium, copper(II) and cadmium(II) gentisates.

Science.gov (United States)

Regulska, E; Kalinowska, M; Wojtulewski, S; Korczak, A; Sienkiewicz-Gromiuk, J; Rzączyńska, Z; Swisłocka, R; Lewandowski, W

2014-11-11

The DFT calculations (B3LYP method with 6-311++G(d,p) mixed with LanL2DZ for transition metals basis sets) for different conformers of 2,5-dihydroxybenzoic acid (gentisic acid), sodium 2,5-dihydroxybenzoate (gentisate) and copper(II) and cadmium(II) gentisates were done. The proposed hydrated structures of transition metal complexes were based on the results of experimental findings. The theoretical geometrical parameters and atomic charge distribution were discussed. Moreover Na, Cu(II) and Cd(II) gentisates were synthesized and the composition of obtained compounds was revealed by means of elemental and thermogravimetric analyses. The FT-IR and FT-Raman spectra of gentisic acid and gentisates were registered and the effect of metals on the electronic charge distribution of ligand was discussed. Copyright © 2014 Elsevier B.V. All rights reserved.

Thermogravimetric investigation on the degradation properties and combustion performance of bio-oils.

Science.gov (United States)

Ren, Xueyong; Meng, Jiajia; Moore, Andrew M; Chang, Jianmin; Gou, Jinsheng; Park, Sunkyu

2014-01-01

The degradation properties and combustion performance of raw bio-oil, aged bio-oil, and bio-oil from torrefied wood were investigated through thermogravimetric analysis. A three-stage process was observed for the degradation of bio-oils, including devolatilization of the aqueous fraction and light compounds, transition of the heavy faction to solid, and combustion of carbonaceous residues. Pyrolysis kinetics parameters were calculated via the reaction order model and 3D-diffusion model, and combustion indexes were used to qualitatively evaluate the thermal profiles of tested bio-oils for comparison with commercial oils such as fuel oils. It was found that aged bio-oil was more thermally instable and produced more combustion-detrimental carbonaceous solid. Raw bio-oil and bio-oil from torrefied wood had comparable combustion performance to fuel oils. It was considered that bio-oil has a potential to be mixed with or totally replace the fuel oils in boilers. Copyright © 2013 Elsevier Ltd. All rights reserved.

Pyrolysis of olive residue/low density polyethylene mixture:Part I Thermogravimetric kinetics

Institute of Scientific and Technical Information of China (English)

无

2008-01-01

This paper demonstrates the thermal pyrolysis of olive residue, low density polyethylene (LDPE) and olive residue/LDPE mixture in an inert atmosphere of N2 using thermogravimetric analysis (TGA). Measurements were carried out in the temperature range 300K~973K at heating rates of 2K/min, 10K/min, 20K/min and 50K/min. Based on the results obtained, three temperature regimes were selected for studying the non-isothermal kinetics of olive residue/LDPE mixture. The first two were dominated by the olive residue pyrolysis, while the third was linked to the LDPE pyrolysis, which occurred at much higher temperatures. Discrepancies between the experimental and calculated TG/DTG profiles were considered as a measurement of the extent of interactions occurring on co-pyrolysis. The maximum degradation temperatures of each component in the mixture were higher than those the individual components;thus an increase in thermal stability was expected. The kinetic parameters associated with thermal degradation were determined using Friedman isoconversional method.

Pyrolysis of tyre powder using microwave thermogravimetric analysis: Effect of microwave power.

Science.gov (United States)

Song, Zhanlong; Yang, Yaqing; Zhou, Long; Zhao, Xiqiang; Wang, Wenlong; Mao, Yanpeng; Ma, Chunyuan

2017-02-01

The pyrolytic characteristics of tyre powder treated under different microwave powers (300, 500, and 700 W) were studied via microwave thermogravimetric analysis. The product yields at different power levels were studied, along with comparative analysis of microwave pyrolysis and conventional pyrolysis. The feedstock underwent preheating, intense pyrolysis, and final pyrolysis in sequence. The main and secondary weight loss peaks observed during the intense pyrolysis stage were attributed to the decomposition of natural rubbers and synthetic rubbers, respectively. The total mass loss rates, bulk temperatures, and maximum temperatures were distinctively higher at higher powers. However, the maximum mass loss rate (0.005 s -1 ), the highest yields of liquid product (53%), and the minimum yields of residual solid samples (43.83%) were obtained at 500 W. Compared with conventional pyrolysis, microwave pyrolysis exhibited significantly different behaviour with faster reaction rates, which can decrease the decomposition temperatures of both natural and synthetic rubber by approximately 110 °C-140 °C.

Shape-selective dependence of room temperature ferromagnetism induced by hierarchical ZnO nanostructures

CSIR Research Space (South Africa)

Motaung, DE

2014-05-01

Full Text Available . These materials were synthesized in a shape-selective manner using simple microwave assisted hydrothermal synthesis. Thermogravimetric analyses demonstrated the as-synthesized ZnO nanostructures to be stable and of high purity. Structural analyses showed...

Kinetic analysis on the non-isothermal degradation of plum stone waste by thermogravimetric analysis and integral master-plots method.

Science.gov (United States)

Ceylan, Selim

2015-04-01

In this study, pyrolysis of plum stone was investigated by thermogravimetric analysis in a nitrogen atmosphere at heating rates of 5, 10, 20 and 40 °C min(-1). Pyrolysis characteristics and the thermal-decomposition rate were significantly affected by variation in the heating rate. However, the heating rate slightly affected the total yield of the volatile matters. Activation energy of the pyrolysis reaction was evaluated by model-free methods, Friedman and Kissingere-Akahirae-Sunose. Results of the Master-Plots method indicated that the most probable reaction model function was the nth order reaction model function as f(x) = (1-x) (3.11), A = 8.02x10(12) under a mean activation energy of 150.61 kJ mol(-1). Proximate and ultimate analysis showed that plum stone can be considered as a favourable source for energy production owing to its low moisture and ash content, and high volatile matter ratio and moderate heating value. © The Author(s) 2015.

Comparative evaluation of thermal oxidative decomposition for oil-plant residues via thermogravimetric analysis: Thermal conversion characteristics, kinetics, and thermodynamics.

Science.gov (United States)

Chen, Jianbiao; Wang, Yanhong; Lang, Xuemei; Ren, Xiu'e; Fan, Shuanshi

2017-11-01

Thermal oxidative decomposition characteristics, kinetics, and thermodynamics of rape straw (RS), rapeseed meal (RM), camellia seed shell (CS), and camellia seed meal (CM) were evaluated via thermogravimetric analysis (TGA). TG-DTG-DSC curves demonstrated that the combustion of oil-plant residues proceeded in three stages, including dehydration, release and combustion of organic volatiles, and chars oxidation. As revealed by combustion characteristic parameters, the ignition, burnout, and comprehensive combustion performance of residues were quite distinct from each other, and were improved by increasing heating rate. The kinetic parameters were determined by Coats-Redfern approach. The results showed that the most possible combustion mechanisms were order reaction models. The existence of kinetic compensation effect was clearly observed. The thermodynamic parameters (ΔH, ΔG, ΔS) at peak temperatures were calculated through the activated complex theory. With the combustion proceeding, the variation trends of ΔH, ΔG, and ΔS for RS (RM) similar to those for CS (CM). Copyright © 2017 Elsevier Ltd. All rights reserved.

Thermal behavior and kinetics assessment of ethanol/gasoline blends during combustion by thermogravimetric analysis

International Nuclear Information System (INIS)

3, CEP 12.516-410 Guaratinguetá, SP (Brazil); U.T.P. – Universidad Tecnológica de Pereira, Faculty of Mechanical Engineering, Pereira, Risaralda (Colombia))" data-affiliation=" (UNESP – Univ Estadual Paulista, Campus of Guaratinguetá, Department of Energy, Laboratory of Combustion and Carbon Capture LC3, CEP 12.516-410 Guaratinguetá, SP (Brazil); U.T.P. – Universidad Tecnológica de Pereira, Faculty of Mechanical Engineering, Pereira, Risaralda (Colombia))" >Rios Quiroga, Luis Carlos; 3, CEP 12.516-410 Guaratinguetá, SP (Brazil))" data-affiliation=" (UNESP – Univ Estadual Paulista, Campus of Guaratinguetá, Department of Energy, Laboratory of Combustion and Carbon Capture LC3, CEP 12.516-410 Guaratinguetá, SP (Brazil))" >Balestieri, José 3, CEP 12.516-410 Guaratinguetá, SP (Brazil))" data-affiliation=" (UNESP – Univ Estadual Paulista, Campus of Guaratinguetá, Department of Energy, Laboratory of Combustion and Carbon Capture LC3, CEP 12.516-410 Guaratinguetá, SP (Brazil))" >Antonio Perrella; 3, CEP 12.516-410 Guaratinguetá, SP (Brazil))" data-affiliation=" (UNESP – Univ Estadual Paulista, Campus of Guaratinguetá, Department of Energy, Laboratory of Combustion and Carbon Capture LC3, CEP 12.516-410 Guaratinguetá, SP (Brazil))" >Ávila, Ivonete

2017-01-01

Highlights: • Kinetic parameters of thermal decomposition events were obtained. • Thermal analysis was used as a tool for understanding combustion processes. • Blends would be classified using thermogravimetric analysis technics. • Synergistic effect of ethanol mixed with gasoline was studied and defined. • Relative error and activation energy values were used to analyze the synergy. - Abstract: The use of ethanol as a fuel or as an additive blended with gasoline is very important for most countries, which aim to reduce the heavy dependence on fossil fuels and mitigate greenhouse gases emission. An increased use of ethanol-gasoline blends has placed great relevance on acquiring knowledge about their physical and chemical properties. Thus, knowledge of such properties favors a better understanding of the effect of the percentage of ethanol/gasoline blends on engine performance. Thence, the present study has established a correlation between activation energy and synergetic effects, obtained by a thermal analysis, and ethanol content in gasoline for different blends in order to use this technique as a tool to classify these blends in the process in order to obtain useful energy in spark ignition engines. For such a purpose, a kinetic study has been conducted through a simultaneous thermal analysis system – TGA (thermogravimetry analysis) and DTA (differential thermal analysis) by following the methodology of non-isothermal tests. Thermogravimetric tests were performed and fuel activation energies for gasoline, ethanol, and percentages of 5, 10, 15, 20, 25, 30, 50, and 75% (%v) ethanol mixed with gasoline, which was achieved by the model free kinetics. The analysis results suggest that the theoretical curves characteristics of the thermal decomposition of ethanol-gasoline blends are rather different due to their ethanol content. Furthermore, it was observed significant interactions and synergistic effects, especially regarding those with low ethanol

Thermogravimetric Analysis of Textile Dyeing Sludge (TDS) in N₂/CO₂/O₂ Atmospheres and its Combustion Model with Coal.

Science.gov (United States)

Zhuo, Zhongxu; Liu, Jingyong; Sun, Shuiyu; Kuo, Jiahong; Sun, Jian; Chang, Ken-Lin; Fu, Jiewen

2018-01-01

  The combustion characteristics of textile dyeing sludge (TDS) in N2/O2, CO2/O2, and N2/CO2 atmospheres, and blends of TDS with coal were analyzed using TGA (thermogravimetric analysis). Results showed that the replacement of N2 by CO2 resulted in negative effects on the combustion and pyrolysis of TDS. Comparing N2/O2 and CO2/O2 atmospheres, combustion of TDS was easier in a N2/O2 atmosphere, but the residual mass after TDS pyrolysis in pure CO2 was less than that in N2 by approximately 4.51%. When the proportion of TDS was 30-50% in the blends of coal with TDS, a synergistic interaction clearly occurred, and it significantly promoted combustion. In considering different combustion parameters, the optimal proportion of TDS may be between 20-30%. The activation energy Ea value decreased from 155.6 kJ/mol to 53.35 kJ/mol with an increasing TDS proportion from 0% to 50%, and it rapidly decreased when the TDS proportion was below 20%.

Consequences of poly(vinyl chloride) presence on the thermochemical process of lignocellulosic biomass in CO₂ by thermogravimetric analysis.

Science.gov (United States)

He, Yao; Ma, Xiaoqian; Zeng, Guangbo

2015-02-01

The thermochemical processes of lignocellulosic biomass and its mixtures with poly(vinyl chloride) (PVC) fractions were investigated by thermogravimetric analysis in CO2 atmosphere. Superposition property was assumed to examine whether and/or to what extent interactions occurred during the mixture decomposition. Results showed that interactions existed, of which the intensities changed with reaction stage, heating rate and PVC quantity, and they actively behaved toward the decomposition in most cases. With PVC presence, lignocellulosic biomass turned from three-stage to four-stage decomposition process where the reactions occurred at lower temperatures with heightened intensity, especially in the first stage. The measured activation energies calculated by Ozawa-Flynn-Wall and Vyazovkin methods were of minor difference <5 kJ/mol, and comparing them between materials in each stage confirmed the results of interaction impact. This work provides a theoretical basis bringing about the possibilities of recycling CO2 into a reaction medium of thermo-treatment of lignocellulosic material with PVC contaminants. Copyright © 2014 Elsevier Ltd. All rights reserved.

Combustion studies of coal derived solid fuels by thermogravimetric analysis. III. Correlation between burnout temperature and carbon combustion efficiency

Science.gov (United States)

Rostam-Abadi, M.; DeBarr, J.A.; Chen, W.T.

1990-01-01

Burning profiles of 35-53 ??m size fractions of an Illinois coal and three partially devolatilized coals prepared from the original coal were obtained using a thermogravimetric analyzer. The burning profile burnout temperatures were higher for lower volatile fuels and correlated well with carbon combustion efficiencies of the fuels when burned in a laboratory-scale laminar flow reactor. Fuels with higher burnout temperatures had lower carbon combustion efficiencies under various time-temperature conditions in the laboratory-scale reactor. ?? 1990.

Effect of superfine grinding on the physico-chemical, morphological and thermogravimetric properties of Lentinus edodes mushroom powders.

Science.gov (United States)

Ming, Jian; Chen, Long; Hong, Hui; Li, Jinlong

2015-09-01

Lentinus edodes is an edible mushroom commonly known as shiitake, which is the second most produced and consumed edible mushroom in the world and is an important nutrient source in the human diet. To fully use L. edodes, the mushrooms are occasionally ground into powder as a flavourful and functional food additive. This study produces powders from the cap and stipe of Lentinus edodes mushrooms through superfine grinding. These powders are composed of sub-micron range particles with various size distributions. The superfine grinding process is then compared with shear pulverisation to determine the different effects on both the cap and stipe powders in terms of particle size and physico-chemical, morphological and thermogravimetric properties. When average particle size was reduced to 0.54 and 0.46 µm, respectively, the moisture and protein content, angles of repose and slide, and water holding capacity of the powders decreased to varied extents. However, soluble dietary fibre, water solubility index, and swelling capacity increased. Scanning electron microscope images suggested that the superfine grinding process effectively changed the original surface structure of the L. edodes powders. The curves of thermogravimetric analysis and those of the derivatives of thermogravimetry indicated that superfine grinding can improve the thermostability of L. edodes powders. Furthermore, superfinely ground L. edodes powders may be used as pharmaceutical or food additives in various fields. The present study suggests that superfinely ground L. edodes powders may be applied in various fields as pharmaceutical or food additives. © 2014 Society of Chemical Industry.

Thermogravimetric studies of high temperature reactions between potassium salts and chromium

International Nuclear Information System (INIS)

Lehmusto, J.; Lindberg, D.; Yrjas, P.; Skrifvars, B.-J.; Hupa, M.

2012-01-01

Highlights: ► K 2 CO 3 reacted with Cr 2 O 3 forming K 2 CrO 4 . ► Presence of chlorine did not alone explain the initiation of accelerated oxidation. ► More light was shed to the role of chromates in accelerated oxidation. ► Accelerated oxidation of chromia protected steels occurs in two consecutive stages. ► Both potassium and chloride are required, so that both stages of reaction occur. - Abstract: This study compares the high temperature reactions of potassium chloride (KCl) and potassium carbonate (K 2 CO 3 ), two salts found in fly ashes formed in biomass combustion, with both pure metallic chromium (Cr) and chromium oxide (Cr 2 O 3 ). The reactions were investigated with thermogravimetric measurements and the results discussed based on thermodynamic calculations. In simple terms: potassium chloride reacted with chromium forming potassium chromate (K 2 CrO 4 ) and chromium oxide. Potassium chloride did not react with chromium oxide. Potassium carbonate reacted with chromium oxide, but not with chromium. The presence of potassium is sufficient to initiate accelerated oxidation, but chloride is needed to sustain it.

Analysis of Mechanical and Thermogravimetric Properties of Composite Materials Based on PVA/MWCNT and Styrene-Acrylic Copolymer/MWCNT

Science.gov (United States)

Volynets, N. I.; Poddubskaya, O. G.; Demidenko, M. I.; Lyubimov, A. G.; Kuzhir, P. P.; Suslyaev, V. I.; Pletnev, M. A.; Zicans, Janis

2017-08-01

Mechanical and thermogravimetric properties of polymer composite materials with various concentrations of multiwalled carbon nanotubes effectively shielding radiation in the radio frequency (20 Hz - 1 MHz) and microwave (26-36 GHz) frequency ranges are studied. As a matrix, widely available polymeric materials, such as polyvinyl acetate and styrene-acrylate, were used in the form of dispersions. From the analysis of the obtained experimental data, it was shown that the introduction of carbon nanotubes into the polymer matrix makes it possible to increase mechanical properties and thermal stability of composite materials.

Thermogravimetric studies of the thermo-oxidative stability of irradiated and unirradiated polyethylene

International Nuclear Information System (INIS)

Novakovic, L.; Gal, O.; Markovic, V.; Stannett, V.T.

1985-01-01

In part one of this series the effects of a phenolic, an amine and a thioester antioxidant on the thermo-oxidative stability of irradiated and unirradiated low-density polyethylene was reported. In this paper the effects of combined phenolic and thioester stabilizers are described. Isothermal thermogravimetric analysis was used to study the systems. Pronounced synergism was observed with the induction periods, the time when the initial weight loss begins and the 5% weight loss. At about 50% of each stabilizer increases greater than twofold were observed both with the unirradiated and irradiated polymers. The rate constants for oxygen uptake were decreased. However, the rates of degradation at 5% weight loss fell between the values of the two pure stabilizers with no pronounced synergism in either case. In the absence of oxygen little effect of either antioxidant or their mixtures was observed. The corresponding activation energies were somewhat higher, however, with the irradiated samples containing antioxidants. Dynamic thermogravimetry was used for this study. A kinetic analysis indicated that there were somewhat different modes of degradation at lower- and higher-temperature ranges. (author)

Thermogravimetric and kinetic analysis of thermal decomposition characteristics of low-lipid microalgae.

Science.gov (United States)

Gai, Chao; Zhang, Yuanhui; Chen, Wan-Ting; Zhang, Peng; Dong, Yuping

2013-12-01

The thermal decomposition behavior of two microalgae, Chlorella pyrenoidosa (CP) and Spirulina platensis (SP), were investigated on a thermogravimetric analyzer under non-isothermal conditions. Iso-conversional Vyazovkin approach was used to calculate the kinetic parameters, and the universal integral method was applied to evaluate the most probable mechanisms for thermal degradation of the two feedstocks. The differential equations deduced from the models were compared with experimental data. For the range of conversion fraction investigated (20-80%), the thermal decomposition process of CP could be described by the reaction order model (F3), which can be calculated by the integral equation of G(α) = [(1 - α)(-2) - 1]/2. And the apparent activation energy was in the range of 58.85-114.5 kJ/mol. As for SP, it can be described by the reaction order model (F2), which can be calculated by the integral equation of G(α) = (1 - α)(-1) - 1, and the range of apparent activation energy was 74.35-140.1 kJ/mol. Copyright © 2013 Elsevier Ltd. All rights reserved.

A comprehensive evaluation of water uptake on atmospherically relevant mineral surfaces: DRIFT spectroscopy, thermogravimetric analysis and aerosol growth measurements

Directory of Open Access Journals (Sweden)

R. J. Gustafsson

2005-01-01

Full Text Available The hygroscopicity of mineral aerosol samples has been examined by three independent methods: diffuse reflectance infrared Fourier transform spectroscopy, thermogravimetric analysis and differential mobility analysis. All three methods allow an evaluation of the water coverage of two samples, CaCO3 and Arizona Test dust, as a function of relative humidity. For the first time, a correlation between absolute gravimetric measurements and the other two (indirect methods has been established. Water uptake isotherms were reliably determined for both solids which at 298 K and 80% relative humidity exhibited similar coverages of ~4 monolayers. However, the behaviour at low relative humidity was markedly different in the two cases, with Arizona Test Dust showing a substantially higher affinity for water in the contact layer. This is understandable in terms of the chemical composition of these two materials. The mobility analysis results are in good accord with field observations and with our own spectroscopic and gravimetric measurements. These findings are of value for an understanding of atmospheric chemical processes.

Thermogravimetric kinetic modelling of in-situ catalytic pyrolytic conversion of rice husk to bioenergy using rice hull ash catalyst.

Science.gov (United States)

Loy, Adrian Chun Minh; Gan, Darren Kin Wai; Yusup, Suzana; Chin, Bridgid Lai Fui; Lam, Man Kee; Shahbaz, Muhammad; Unrean, Pornkamol; Acda, Menandro N; Rianawati, Elisabeth

2018-04-07

The thermal degradation behaviour and kinetic parameter of non-catalytic and catalytic pyrolysis of rice husk (RH) using rice hull ash (RHA) as catalyst were investigated using thermogravimetric analysis at four different heating rates of 10, 20, 50 and 100 K/min. Four different iso conversional kinetic models such as Kissinger, Friedman, Kissinger-Akahira-Sunose (KAS) and Ozawa-Flynn-Wall (OFW) were applied in this study to calculate the activation energy (E A ) and pre-exponential value (A) of the system. The E A of non-catalytic and catalytic pyrolysis was found to be in the range of 152-190 kJ/mol and 146-153 kJ/mol, respectively. The results showed that the catalytic pyrolysis of RH had resulted in a lower E A as compared to non-catalytic pyrolysis of RH and other biomass in literature. Furthermore, the high Gibb's free energy obtained in RH implied that it has the potential to serve as a source of bioenergy production. Copyright © 2018 Elsevier Ltd. All rights reserved.

Differential thermal, Thermogravimetric and X-ray diffraction investigation of hydration phases in cementitious waste form

International Nuclear Information System (INIS)

Khalil, M.Y.; Nagy, M.E.; El-Sourougy, M.R.; Zaki, A.A.

1996-01-01

Hydration phases of cement determine the final properties of the product. Adding other components to the cement paste may alter the final phases formed and affect properties of the hardened products. In this work ordinary portland cement and/or blast furnace slag cement were hardened with low-or intermediate-level radioactive liquid wastes and different additives. Hydration phases were investigated using differential thermal, thermogravimetric, and X-ray diffraction techniques. Low-and intermediate-level liquid wastes were found not to affect the hydration phases of cement. The addition of inorganic exchangers and latex were found to affect the hydration properties of the cement waste system. This resulted in a reduction of compressive strength. On the contrary, addition of epoxy also affected the hydration causing increase in compressive strength. 10 figs., 2 tabs

Water desorption of cassava starch granules: A study based on thermogravimetric analysis of aqueous suspensions and humid powders.

Science.gov (United States)

Ayala Valencia, Germán; Djabourov, Madeleine; do Amaral Sobral, Paulo José

2016-08-20

This work reports on water desorption from cassava starch in relation with the structure and conditioning of granules in suspensions or after equilibration in desiccators. The experimental work is performed by thermogravimetric analysis with isothermal and non-isothermal protocols and interpreted to derive the activation energies and desorption frequencies according to the humidity range with no adjustable parameter. The analysis points out the different types of water interacting with the starch granules and relates the drying coefficients to their microscopic structure. The work helps clarifying contradictory and partial results from the literature. Copyright © 2016 Elsevier Ltd. All rights reserved.

Investigation of co-combustion characteristics of sewage sludge and coffee grounds mixtures using thermogravimetric analysis coupled to artificial neural networks modeling.

Science.gov (United States)

Chen, Jiacong; Liu, Jingyong; He, Yao; Huang, Limao; Sun, Shuiyu; Sun, Jian; Chang, KenLin; Kuo, Jiahong; Huang, Shaosong; Ning, Xunan

2017-02-01

Artificial neural network (ANN) modeling was applied to thermal data obtained by non-isothermal thermogravimetric analysis (TGA) from room temperature to 1000°C at three different heating rates in air to predict the TG curves of sewage sludge (SS) and coffee grounds (CG) mixtures. A good agreement between experimental and predicted data verified the accuracy of the ANN approach. The results of co-combustion showed that there were interactions between SS and CG, and the impacts were mostly positive. With the addition of CG, the mass loss rate and the reactivity of SS were increased while charring was reduced. Measured activation energies (E a ) determined by the Kissinger-Akahira-Sunose (KAS) and Ozawa-Flynn-Wall (OFW) methods deviated by <5%. The average value of E a (166.8kJ/mol by KAS and 168.8kJ/mol by OFW, respectively) was the lowest when the fraction of CG in the mixture was 40%. Copyright © 2016 Elsevier Ltd. All rights reserved.

Thermogravimetric characteristics and kinetics of scrap tyre and Juglans regia shell co-pyrolysis.

Science.gov (United States)

Uzun, B B; Yaman, E

2014-10-01

The degradation kinetics of Juglans regia shell, scrap tyre and their blends were investigated using a thermogravimetric analysis method. Experiments were performed under dynamic conditions and a nitrogen atmosphere in the range 293 to 973 K at different heating rates. During pyrolysis of J. regia shell three mass loss zones were specified as removal of water, decomposition of hemicelluloses and cellulose, and decomposition of lignin. The degradation curves of scrap tyre showed merely one stage which was due to decomposition of styrene butadiene rubber. The kinetic parameters were calculated using both Arrhenius and Coats-Redfern methods. By adopting the Arrhenius method, the average value of activation energies of J. regia shell, scrap tyre and their 1 : 1 blends were found to be 69.22, 71.48 and 47.03 kJ mol(-1), respectively. Additionally, by using the Coats-Redfern method, the average value of activation energies of J. regia shell, scrap tyre and their 1 : 1 blend were determined as 99.85, 78.72 and 63.81 kJ mol(-1), respectively. The addition of J. regia shell to scrap tyre caused a reduction in the activation energies. The difference of weight loss was measured to examine interactions between raw materials. The maximum difference between experimental and theoretical mass loss was 5% at about 648 K with a heating rate of 20 K min(-1). These results indicated a significant synergistic effect was available during co-pyrolysis of J. regia shell and scrap tyre in the high temperature region. © The Author(s) 2014.

Synthesis, spectroscopic characterization and thermogravimetric analysis of two series of substituted (metallotetraphenylporphyrins

Directory of Open Access Journals (Sweden)

Rasha K. Al-Shewiki

2017-06-01

Full Text Available Subsequent treatment of H2TPP(CO2H4 (tetra(p-carboxylic acid phenylporphyrin, 1 with an excess of oxalyl chloride and HNR2 afforded H2TPP(C(ONR24 (R = Me, 2; iPr, 3 with yields exceeding 80%. The porphyrins 2 and 3 could be converted to the corresponding metalloporphyrins MTPP(C(ONR24 (R = Me/iPr for M = Zn (2a, 3a; Cu (2b, 3b; Ni (2c, 3c; Co (2d, 3d by the addition of 3 equiv of anhydrous MCl2 (M = Zn, Cu, Ni, Co to dimethylformamide solutions of 2 and 3 at elevated temperatures. Metalloporphyrins 2a–d and 3a–d were obtained in yields exceeding 60% and have been, as well as 2 and 3, characterized by elemental analysis, electrospray ionization mass spectrometry (ESIMS and IR and UV–vis spectroscopy. Porphyrins 2, 2a–d and 3, 3a–d are not suitable for organic molecular beam deposition (OMBD, which is attributed to their comparatively low thermal stability as determined by thermogravimetric analysis (TG of selected representatives.

Advanced Behavioral Analyses Show that the Presence of Food Causes Subtle Changes in C. elegans Movement.

Science.gov (United States)

Angstman, Nicholas B; Frank, Hans-Georg; Schmitz, Christoph

2016-01-01

As a widely used and studied model organism, Caenorhabditis elegans worms offer the ability to investigate implications of behavioral change. Although, investigation of C. elegans behavioral traits has been shown, analysis is often narrowed down to measurements based off a single point, and thus cannot pick up on subtle behavioral and morphological changes. In the present study videos were captured of four different C. elegans strains grown in liquid cultures and transferred to NGM-agar plates with an E. coli lawn or with no lawn. Using an advanced software, WormLab, the full skeleton and outline of worms were tracked to determine whether the presence of food affects behavioral traits. In all seven investigated parameters, statistically significant differences were found in worm behavior between those moving on NGM-agar plates with an E. coli lawn and NGM-agar plates with no lawn. Furthermore, multiple test groups showed differences in interaction between variables as the parameters that significantly correlated statistically with speed of locomotion varied. In the present study, we demonstrate the validity of a model to analyze C. elegans behavior beyond simple speed of locomotion. The need to account for a nested design while performing statistical analyses in similar studies is also demonstrated. With extended analyses, C. elegans behavioral change can be investigated with greater sensitivity, which could have wide utility in fields such as, but not limited to, toxicology, drug discovery, and RNAi screening.

Advanced behavioral analyses show that the presence of food causes subtle changes in C. elegans movement

Directory of Open Access Journals (Sweden)

Nicholas eAngstman

2016-03-01

Full Text Available As a widely used and studied model organism, C. elegans worms offer the ability to investigate implications of behavioral change. Although investigation of C. elegans behavioral traits has been shown, analysis is often narrowed down to measurements based off a single point, and thus cannot pick up on subtle behavioral and morphological changes. In the present study videos were captured of four different C. elegans strains grown in liquid cultures and transferred to NGM-agar plates with an E. coli lawn or with no lawn. Using an advanced software, WormLab, the full skeleton and outline of worms were tracked to determine whether the presence of food affects behavioral traits. In all seven investigated parameters, statistically significant differences were found in worm behavior between those moving on NGM-agar plates with an E. coli lawn and NGM-agar plates with no lawn. Furthermore, multiple test groups showed differences in interaction between variables as the parameters that significantly correlated statistically with speed of locomotion varied. In the present study, we demonstrate the validity of a model to analyze C. elegans behavior beyond simple speed of locomotion. The need to account for a nested design while performing statistical analyses in similar studies is also demonstrated. With extended analyses, C. elegans behavioral change can be investigated with greater sensitivity, which could have wide utility in fields such as, but not limited to, toxicology, drug discovery, and RNAi screening.

Determination of the surface density of polyethylene glycol on gold nanoparticles by use of microscale thermogravimetric analysis.

Science.gov (United States)

Sebby, K B; Mansfield, E

2015-04-01

The widespread integration of nanoparticle technologies into biomedicine will depend on the ability to repeatedly create particles with well-defined properties and predictable behaviors. For this to happen, fast, reliable, inexpensive, and widely available techniques to characterize nanomaterials are needed. Characterization of the surface molecules is particularly important since the surface, including the surface molecule density, plays a dominant role in determining how nanoparticles interact with their surroundings. Here, 10 and 30 nm gold nanoparticle NIST Standard Reference Materials were functionalized with fluorescently labeled polyethylene glycol (PEG) with either thiolate or lipoic acid anchoring groups to evaluate analytical techniques for determining surface coverage. The coating of the nanoparticles was confirmed with dynamic light scattering, microscale thermogravimetric analysis (μ-TGA), and ultraviolet-visible (UV-vis) spectroscopy. A UV-vis method for determining gold nanoparticle concentrations that takes into account spectral broadening upon functionalization was developed. The amount of bound PEG was quantified with μ-TGA, a technique analogous to thermogravimetric analysis that uses quartz crystal microbalances, and fluorescence spectroscopy of displaced ligands. It is shown that μ-TGA is a convenient technique for the quantification of ligands bound to inorganic particles while sacrificing a minimal amount of sample, and the treatment of the functionalized nanoparticle dispersions with dithiothreitol may be insufficient to achieve complete displacement of the surface ligands for quantification by fluorescence measurements. The μ-TGA and fluorescence results were used to determine ligand footprint sizes-average areas occupied by each ligand on the particles' surface. The lipoic acid bound ligands had footprint sizes of 0.21 and 0.25 nm(2) on 10 and 30 nm particles, respectively while the thiolate ligands had footprint sizes of 0.085 and 0

Thermogravimetric pyrolysis kinetics of bamboo waste via Asymmetric Double Sigmoidal (Asym2sig) function deconvolution.

Science.gov (United States)

Chen, Chuihan; Miao, Wei; Zhou, Cheng; Wu, Hongjuan

2017-02-01

Thermogravimetric kinetic of bamboo waste (BW) pyrolysis has been studied using Asymmetric Double Sigmoidal (Asym2sig) function deconvolution. Through deconvolution, BW pyrolytic profiles could be separated into three reactions well, each of which corresponded to pseudo hemicelluloses (P-HC), pseudo cellulose (P-CL), and pseudo lignin (P-LG) decomposition. Based on Friedman method, apparent activation energy of P-HC, P-CL, P-LG was found to be 175.6kJ/mol, 199.7kJ/mol, and 158.4kJ/mol, respectively. Energy compensation effects (lnk 0, z vs. E z ) of pseudo components were in well linearity, from which pre-exponential factors (k 0 ) were determined as 6.22E+11s -1 (P-HC), 4.50E+14s -1 (P-CL) and 1.3E+10s -1 (P-LG). Integral master-plots results showed pyrolytic mechanism of P-HC, P-CL, and P-LG was reaction order of f(α)=(1-α) 2 , f(α)=1-α and f(α)=(1-α) n (n=6-8), respectively. Mechanism of P-HC and P-CL could be further reconstructed to n-th order Avrami-Erofeyev model of f(α)=0.62(1-α)[-ln(1-α)] -0.61 (n=0.62) and f(α)=1.08(1-α)[-ln(1-α)] 0.074 (n=1.08). Two-steps reaction was more suitable for P-LG pyrolysis. Copyright © 2016 Elsevier Ltd. All rights reserved.

Thermogravimetric-mass spectrometric study on the evolution of nitrogen compounds during coal devolatilisation

Energy Technology Data Exchange (ETDEWEB)

Arenillas, A.; Rubiera, F.; Pevida, C.; Pis, J.J. [Department of Energy and Environment, Instituto Nacional del Carbon, CSIC, Apartado 73, 33080 Oviedo (Spain)

2002-10-01

Emissions of nitrogen oxides during coal combustion are a major environmental problem. The chemically bound nitrogen in fuel accounts for up to 80% of total NO{sub x} emissions. In this respect, fundamental studies are needed to clarify the mechanisms and to identify the different species that are precursors in the formation of the NO{sub x}. Mass spectrometry (MS) has been used for decades as a successful technique in evolved gas analysis. However, MS is normally used to identify typical volatile compounds formed during coal pyrolysis (i.e. H{sub 2}, CH{sub 4}, CO, CO{sub 2} and H{sub 2}O) but very few works on the detection by MS of nitrogen compounds during coal devolatilisation can be found. In this work, the possibility of detecting different nitrogen compounds by means of thermogravimetric-MS during the temperature-programmed pyrolysis of coal was evaluated. Interferences in the N-compounds MS signals were determined. The use of model compounds provided additional information on the MS response factors of the volatile compounds produced.

Thermogravimetric Studies of Deposited Potash Impregnated for Flame-Retardancy into a Cotton Fabric

Institute of Scientific and Technical Information of China (English)

MOSTASHARI, S.M.; NIA, Y.K.; BAIE, S.

2007-01-01

The effect of potash as a nondurable finish on the flammability of 100% cotton fabric (plain 180 g/m2) was investigated. The bone-dried weighed fabrics were dipped into suitable concentrations of potash, with a volume of 100 mL at 20-2 ℃. The impregnation was followed by means of squeeze rolls and drying at 110 C. The samples were then reweighed with analytical precision. After conditioning overnight by using our "vertical flame tester" the optimum add-on values to impart flame-retardancy to cotton fabric was determined and expressed by 0.80 g of potash per 100 g fabric to be an efficient addition. Thermogravimetric analysis of pure cotton, treated cotton with potash at its optimum efficiency for donation of flame-retardancy into cotton fabric was fulfilled and the thermograms were compared and commented. The effectiveness of this hydroxide was attributed to the heat dissipation by the remaining consumed material during the combustion. The results obtained are in favor of "Dust or Wall Effect Theory".

Combustion kinetics of hydrochar produced from hydrothermal carbonisation of Karanj (Pongamia pinnata) fruit hulls via thermogravimetric analysis.

Science.gov (United States)

Islam, Md Azharul; Kabir, G; Asif, M; Hameed, B H

2015-10-01

This study examined the combustion profile and kinetics of hydrochar produced from hydrothermal carbonisation (HTC) of Karanj fruit hulls (KFH). The HTC-KFH hydrochar combustion kinetics was investigated at 5, 10, and 20°C/min by thermogravimetric analysis. The kinetics model, Kissinger-Akahira-Sunose revealed the combustion kinetics parameters for the extent of conversion from 0.1 to 0.8; the activation energy varies from 114 to 67 kJ/mol respectively. The hydrochar combustion followed multi-steps kinetics; the Coats-Redfern models predicted the activation energies and pre-exponential constants for the hydrochar combustion zones. The diffusion models are the effective mechanism in the second and third zone. Copyright © 2015 Elsevier Ltd. All rights reserved.

Thermogravimetric investigation of the co-combustion between the pyrolysis oil distillation residue and lignite.

Science.gov (United States)

Li, Hao; Xia, Shuqian; Ma, Peisheng

2016-10-01

Co-combustion of lignite with distillation residue derived from rice straw pyrolysis oil was investigated by non-isothermal thermogravimetric analysis (TGA). The addition of distillation residue improved the reactivity and combustion efficiency of lignite, such as increasing the weight loss rate at peak temperature and decreasing the burnout temperature and the total burnout. With increasing distillation residue content in the blended fuels, the synergistic interactions between distillation residue and lignite firstly increased and then decreased during co-combustion stage. Results of XRF, FTIR, (13)C NMR and SEM analysis indicated that chemical structure, mineral components and morphology of samples have great influence on the synergistic interactions. The combustion mechanisms and kinetic parameters were calculated by the Coats Redfern model, suggesting that the lowest apparent activation energy (120.19kJ/mol) for the blended fuels was obtained by blending 60wt.% distillation residue during main co-combustion stage. Copyright © 2016 Elsevier Ltd. All rights reserved.

Thermogravimetric study of a Phase Change Slurry: Effect of variable conditions

International Nuclear Information System (INIS)

Giro-Paloma, J.; Valle-Zermeño, R. del; Fernández, A.I.; Chimenos, J.M.; Formosa, J.

2016-01-01

Highlights: • Dry or wet PCS present differences in their thermal behavior. • The optimum conditions of dry PCS were determined by TGA. • Type of atmosphere and heating rate were the variables under consideration. • T peak can be accurately determined at 1 °C·min −1 in N 2. • Fusion/latent heat can be best determined at 10 °C·min −1 . - Abstract: Microcapsules containing Phase Change Materials (MPCM) are widely used for passive systems in energy storage. When MPCM are mixed with a carrier fluid, Phase Change Slurries (PCS) are used for heat transfer fluids in active systems or heat transport systems. The thermal behavior of PCS can be measured as dry or wet basis, resulting in important differences in weight losses. This study explores the optimum conditions for analyzing the thermal behavior of dried PCS by thermogravimetric analysis (TGA) varying the parameter conditions for obtaining peak temperature and heat flow (latent heat). The factors that were taken into account were the atmosphere of study (air and nitrogen) and the heating rate (0.5, 1, 5, and 10 °C·min −1 ). The best conditions to determine peak temperature are at 1 °C·min −1 and in N 2 atmosphere, whereas the decomposition fusion/latent heat of the sample is improved at higher heating velocities towards 10 °C·min −1 .

Pyrolysis kinetics and thermal behavior of waste sawdust biomass using thermogravimetric analysis.

Science.gov (United States)

Mishra, Ranjeet Kumar; Mohanty, Kaustubha

2018-03-01

The present study reports pyrolysis behavior of three waste biomass using thermogravimetric analysis to determine kinetic parameters at five different heating rates. Physiochemical characterization confirmed that these biomass have the potential for fuel and energy production. Pyrolysis experiments were carried out at five different heating rates (5-25 °C min -1 ). Five model-free methods such as Kissinger-Akahira-Sunose (KAS), Ozawa-Flynn-Wall (OFW), Friedman, Coats-Redfern, and distributed activation energy (DAEM) were used to calculate the kinetic parameters. The activation energy was found to be 171.66 kJ mol -1 , 148.44 kJ mol -1 , and 171.24 kJ mol -1 from KAS model; 179.29 kJ mol -1 , 156.58 kJ mol -1 , and 179.47 kJ mol -1 from OFW model; 168.58 kJ mol -1 , 181.53 kJ mol -1 , and 184.61 kJ mol -1 from Friedman model; and 206.62 kJ mol -1 , 171.63 kJ mol -1 , and 160.45 kJ mol -1 from DAEM model for PW, SW, AN biomass respectively. The calculated kinetic parameters are in good agreement with other reported biomass. Copyright © 2017 Elsevier Ltd. All rights reserved.

Studies of the thermal properties of horn keratin by dielectric spectroscopy, thermogravimetric analysis and differential thermal analysis

International Nuclear Information System (INIS)

Marzec, E.; Piskunowicz, P.; Jaroszyk, F.

2002-01-01

The dielectric and thermal properties of horn keratin have been studied bu dielectric spectroscopy in the frequency range 10 1 -10 5 Hz, thermogravimetric analysis (TG) and different thermal analysis (DTA). Measurement of non-irradiated and g amma - irradiated keratin with doses 5, 50 kGy were performed at temperature from 22 to 260 o C. The results revealed the occurrence of phase transitions related to release of loosely bound water and bound water up to 200 o Cand the denaturation of the crystalline structure above this temperature. The influence of γ-irradiation on the thermal behaviour of keratin is significant only in the temperature range of denaturation. The decrease in the temperature of denaturation would suggest that γ-irradiation initiates main-chain degradation. (authors)

Temperature-dependent deliquescence relative humidities and water activities using humidity controlled thermogravimetric analysis with application to malonic acid.

Science.gov (United States)

Beyer, Keith D; Schroeder, Jason R; Kissinger, Jared A

2014-04-03

We utilize a new experimental technique, humidity-controlled thermogravimetric analysis (HTGA), to determine temperature-dependent deliquescence relative humidities (DRH) and to determine the equilibrium concentration of a solution at a given temperature and relative humidity. To that end, we have investigated the malonic acid/water system determining the DRH and concentration/RH relationship in the temperature range 303-278 K. Excellent agreement is found with literature values for the DRH of malonic acid as a function of temperature and for the concentration/RH relationship at several temperatures. Thus, we extend the DRH and concentration/RH relationship to a broader temperature range and are using the HTGA experiments to investigate other organic acids.

Thermogravimetric, Calorimetric, and Structural Studies of the Co3 O4 /CoO Oxidation/Reduction Reaction

Science.gov (United States)

Unruh, Karl; Cichocki, Ronald; Kelly, Brian; Poirier, Gerald

2015-03-01

To better assess the potential of cobalt oxide for thermal energy storage (TES), the Co3O4/CoO oxidation/reduction reaction has been studied by thermogravimetric (TGA), calorimetric (DSC), and x-ray diffraction (XRD) measurements in N2 and atmospheric air environments. TGA measurements showed an abrupt mass loss of about 6.6% in both N2 and air, consistent with the stoichiometric reduction of Co3O4 to CoO and structural measurements. The onset temperature of the reduction of Co3O4 in air was only weakly dependent on the sample heating rate and occurred at about 910 °C. The onset temperature for the oxidation of CoO varied between about 850 and 875 °C for cooling rates between 1 and 20 °C/min, but complete re-conversion to Co3O4 could only be achieved at the slowest cooling rates. Due to the dependence of the rate constant on the oxygen partial pressure, the oxidation of Co3O4 in a N2 environment occurred at temperatures between about 775 and 825 °C for heating rates between 1 and 20 °C/min and no subsequent re-oxidation of the reduced Co3O4 was observed on cooling to room temperature. In conjunction with a measured transition heat of about 600 J/g of Co3O4, these measurements indicate that cobalt oxide is a viable TES material.

Thermal Behaviour of Five Different Date Palm Residues of Algeria by Thermogravimetric Analysis

Directory of Open Access Journals (Sweden)

Siham AMIROU

2013-06-01

Full Text Available Renewable energy has become moreimportant globally especially with the current fuel andeconomic crisis. Date palm biomasses are highlypotential materials for energy resources. The factthat they are renewable and abundantly availableare amongst the attractive reasons of employingthem as the major source for renewable energy. Thepurpose of this research was to investigate thethermal behavior of date palm biomass in order toevaluate their usefulness for energy production. Inmicroparticular scale, the thermogravimetric analysis(TGA is one of the techniques used to determinethe thermal properties of five different date palmresidues that were studied: (date palm rachis (DPR,date palm trunk (DPT, leaf base (Petiole (LB,fruitstalk prunings (FP and liff (LP. The TGAtechnique consists to record the lost weight duringthe increase in temperature from 20°C until 600°Cwith a 10°C/min heating rate. The thermogramspresented a departure phase of free water (fromroom temperature to 110°C before the degradationprocess of the lignocellulosic constituents. The ligninand hemicellulose play an important role on thedegradation of lignocellulosic materials at thetemperature under 250°C. The degradation ofcellulose begins at 250°C and overlaps to that oflignin until 450°C.

Synthesis, spectroscopic characterization and thermogravimetric analysis of two series of substituted (metallo)tetraphenylporphyrins.

Science.gov (United States)

Al-Shewiki, Rasha K; Mende, Carola; Buschbeck, Roy; Siles, Pablo F; Schmidt, Oliver G; Rüffer, Tobias; Lang, Heinrich

2017-01-01

Subsequent treatment of H 2 TPP(CO 2 H) 4 (tetra( p -carboxylic acid phenyl)porphyrin, 1 ) with an excess of oxalyl chloride and HNR 2 afforded H 2 TPP(C(O)NR 2 ) 4 (R = Me, 2 ; iPr, 3 ) with yields exceeding 80%. The porphyrins 2 and 3 could be converted to the corresponding metalloporphyrins MTPP(C(O)NR 2 ) 4 (R = Me/iPr for M = Zn ( 2a , 3a ); Cu ( 2b , 3b ); Ni ( 2c , 3c ); Co ( 2d , 3d )) by the addition of 3 equiv of anhydrous MCl 2 (M = Zn, Cu, Ni, Co) to dimethylformamide solutions of 2 and 3 at elevated temperatures. Metalloporphyrins 2a - d and 3a - d were obtained in yields exceeding 60% and have been, as well as 2 and 3 , characterized by elemental analysis, electrospray ionization mass spectrometry (ESIMS) and IR and UV-vis spectroscopy. Porphyrins 2 , 2a - d and 3 , 3a - d are not suitable for organic molecular beam deposition (OMBD), which is attributed to their comparatively low thermal stability as determined by thermogravimetric analysis (TG) of selected representatives.

Characteristics and kinetic study on pyrolysis of five lignocellulosic biomass via thermogravimetric analysis.

Science.gov (United States)

Chen, Zhihua; Hu, Mian; Zhu, Xiaolei; Guo, Dabin; Liu, Shiming; Hu, Zhiquan; Xiao, Bo; Wang, Jingbo; Laghari, Mahmood

2015-09-01

Pyrolysis characteristics and kinetic of five lignocellulosic biomass pine wood sawdust, fern (Dicranopteris linearis) stem, wheat stalk, sugarcane bagasse and jute (Corchorus capsularis) stick were investigated using thermogravimetric analysis. The pyrolysis of five lignocellulosic biomass could be divided into three stages, which correspond to the pyrolysis of hemicellulose, cellulose and lignin, respectively. Single Gaussian activation energy distributions of each stage are 148.50-201.13 kJ/mol with standard deviations of 2.60-13.37 kJ/mol. The kinetic parameters of different stages were used as initial guess values for three-parallel-DAEM model calculation with good fitting quality and fast convergence rate. The mean activation energy ranges of hemicellulose, cellulose and lignin were 148.12-164.56 kJ/mol, 171.04-179.54 kJ/mol and 175.71-201.60 kJ/mol, with standard deviations of 3.91-9.89, 0.29-1.34 and 23.22-27.24 kJ/mol, respectively. The mass fractions of hemicellulose, cellulose and lignin in lignocellulosic biomass were respectively estimated as 0.12-0.22, 0.54-0.65 and 0.17-0.29. Copyright © 2015 Elsevier Ltd. All rights reserved.

Pyrolysis of biofuels of the future: Sewage sludge and microalgae – Thermogravimetric analysis and modelling of the pyrolysis under different temperature conditions

International Nuclear Information System (INIS)

Soria-Verdugo, Antonio; Goos, Elke; Morato-Godino, Andrés; García-Hernando, Nestor; Riedel, Uwe

2017-01-01

Highlights: • Pyrolysis of microalgae and sewage sludge is studied by thermogravimetric analysis. • Accurate values of the kinetic parameters of the pyrolysis reaction are reported. • Pyrolysis is modeled for parabolic and exponential temperature increases. • Estimations of the model are compared with experimental measurements in TGA. • Excellent agreement is reached between the model estimations and the experiments. - Abstract: The pyrolysis process of both microalgae and sewage sludge was investigated separately, by means of non-isothermal thermogravimetric analysis. The Distributed Activation Energy Model (DAEM) was employed to obtain the pyrolysis kinetic parameters of the samples, i.e. the activation energy E_a and the pre-exponential factor k_0. Nine different pyrolysis tests at different constant heating rates were conducted for each sample in a thermogravimetric analyzer (TGA) to obtain accurate values of the pyrolysis kinetic parameters when applying DAEM. The accurate values of the activation energy and the pre-exponential factor that characterize the pyrolysis reaction of Chlorella vulgaris and sewage sludge were reported, together with their associated uncertainties. The activation energy and pre-exponential factor for the C. vulgaris vary between 150–250 kJ/mol and 10"1"0–10"1"5 s"−"1 respectively, whereas values ranging from 200 to 400 kJ/mol were obtained for the sewage sludge activation energy, and from 10"1"5 to 10"2"5 s"−"1 for its pre-exponential factor. These values of E_a and k_0 were employed to estimate the evolution of the reacted fraction with temperature during the pyrolysis of the samples under exponential and parabolic temperature increases, more typical for the pyrolysis reaction of fuel particles in industrial reactors. The estimations of the relation between the reacted fraction and the temperature for exponential and parabolic temperature increases were found to be in good agreement with the experimental values

Thermogravimetric Analysis of Modified Hematite by Methane (CH{sub 4}) for Chemical-Looping Combustion: A Global Kinetics Mechanism

Energy Technology Data Exchange (ETDEWEB)

Monazam, Esmail R; Breault, Ronald W; Siriwardane, Ranjani; Miller, Duane D

2013-10-01

Iron oxide (Fe{sub 2}O{sub 3}) or in its natural form (hematite) is a potential material to capture CO{sub 2} through the chemical-looping combustion (CLC) process. It is known that magnesium (Mg) is an effective methyl cleaving catalyst and as such it has been combined with hematite to assess any possible enhancement to the kinetic rate for the reduction of Fe{sub 2}O{sub 3} with methane. Therefore, in order to evaluate its effectiveness as a hematite additive, the behaviors of Mg-modified hematite samples (hematite –5% Mg(OH){sub 2}) have been analyzed with regard to assessing any enhancement to the kinetic rate process. The Mg-modified hematite was prepared by hydrothermal synthesis. The reactivity experiments were conducted in a thermogravimetric analyzer (TGA) using continuous stream of CH{sub 4} (5, 10, and 20%) at temperatures ranging from 700 to 825 {degrees}C over ten reduction cycles. The mass spectroscopy analysis of product gas indicated the presence of CO{sub 2}, H{sub 2}O, H{sub 2} and CO in the gaseous product. The kinetic data at reduction step obtained by isothermal experiments could be well fitted by two parallel rate equations. The modified hematite samples showed higher reactivity as compared to unmodified hematite samples during reduction at all investigated temperatures.

Lithium-ion battery electrolyte emissions analyzed by coupled thermogravimetric/Fourier-transform infrared spectroscopy

Science.gov (United States)

Bertilsson, Simon; Larsson, Fredrik; Furlani, Maurizio; Albinsson, Ingvar; Mellander, Bengt-Erik

2017-10-01

In the last few years the use of Li-ion batteries has increased rapidly, powering small as well as large applications, from electronic devices to power storage facilities. The Li-ion battery has, however, several safety issues regarding occasional overheating and subsequent thermal runaway. During such episodes, gas emissions from the electrolyte are of special concern because of their toxicity, flammability and the risk for gas explosion. In this work, the emissions from heated typical electrolyte components as well as from commonly used electrolytes are characterized using FT-IR spectroscopy and FT-IR coupled with thermogravimetric (TG) analysis, when heating up to 650 °C. The study includes the solvents EC, PC, DEC, DMC and EA in various single, binary and ternary mixtures with and without the LiPF6 salt, a commercially available electrolyte, (LP71), containing EC, DEC, DMC and LiPF6 as well as extracted electrolyte from a commercial 6.8 Ah Li-ion cell. Upon thermal heating, emissions of organic compounds and of the toxic decomposition products hydrogen fluoride (HF) and phosphoryl fluoride (POF3) were detected. The electrolyte and its components have also been extensively analyzed by means of infrared spectroscopy for identification purposes.

Thermogravimetric analysis of the co-pyrolysis of paper sludge and municipal solid waste

International Nuclear Information System (INIS)

Fang, Shiwen; Yu, Zhaosheng; Lin, Yousheng; Hu, Shanchao; Liao, Yanfen; Ma, Xiaoqian

2015-01-01

Highlights: • The co-pyrolysis of municipal solid waste, paper sludge and the blends was studied. • The reactivity of paper sludge could be improved by blending municipal solid waste. • The FWO and KAS methods were used to calculate activation energy. • The average activation energy was the minimum by blending 50% paper sludge. - Abstract: The pyrolysis characteristics of municipal solid waste (MSW), paper sludge (PS) and their blends were studied through a thermogravimetric simultaneous thermal analyzer from room temperature to 1000 °C. Meanwhile their kinetics were studied by Flynn–Wall–Ozawa (FWO) and Kissinger–Akahira–Sunose (KAS) methods. The mass proportions of PS in the blends were 10%, 30%, 50%, 70%, 90%, respectively and the experiments were carried out at different heating rates (30, 40 and 50 °C/min). The initial temperature of MSW was lower than that of PS and the terminated temperature was higher than PS. The comprehensive characteristic index decreased progressively along with the decrease of the MSW proportion. The values of average activation energies calculated by FWO and KAS methods were highly consistent. The average activation energy reached the minimum number, 96.7 kJ/mol by KAS and 11.56 kJ/mol by FWO, with the proportion of PS was 50%

Thermogravimetric method of estimation of uranyl cation state in melts of alkali metal chlorides and their mixtures

International Nuclear Information System (INIS)

Vorobej, M.P.; Desyatnik, V.N.

1979-01-01

The thermogravimetric method was used to study the chloridizing of uranium oxides in molten media. The study of the uranium oxide chloridizing served as a basis for evaluating comparatively, using the DTA method, the uranyl-cation state in a melt. Using the alkali metals as example, it was shown that the decomposition of the frozen uranium oxychlorides proceeds with the formation of intermediate chlorouranates. The final product of the thermolysis are uranates Me 2 U 2 O 7 (Me-Li, Na, K, Rb, Cs). The time and the conditions of the change of uranium oxides to the oxyanion [UO 2 Cl 4 ] 2- were determined as a function of the chloridizing agent. The method can be employed for evaluating uranyl-ions in molten media where they are used as electrolytes in the extraction of uranium dioxide

Preparation of Tetramethylguanidine-Functionalized Mesoporous ...

African Journals Online (AJOL)

The catalyst was characterized by various techniques including Diffuse Reflectance FTIR, 13C NMR, elemental analysis and simultaneous thermogravimetric and differential scanning calorimetry analyses. It was then screened in the epoxidation of electron deficient alkenes. The results obtained show that indeed the ...

Pyrolysis characteristics and kinetics of microalgae via thermogravimetric analysis (TGA): A state-of-the-art review.

Science.gov (United States)

Bach, Quang-Vu; Chen, Wei-Hsin

2017-12-01

Pyrolysis is a promising route for biofuels production from microalgae at moderate temperatures (400-600°C) in an inert atmosphere. Depending on the operating conditions, pyrolysis can produce biochar and/or bio-oil. In practice, knowledge for thermal decomposition characteristics and kinetics of microalgae during pyrolysis is essential for pyrolyzer design and pyrolysis optimization. Recently, the pyrolysis kinetics of microalgae has become a crucial topic and received increasing interest from researchers. Thermogravimetric analysis (TGA) has been employed as a proven technique for studying microalgae pyrolysis in a kinetic control regime. In addition, a number of kinetic models have been applied to process the TGA data for kinetic evaluation and parameters estimation. This paper aims to provide a state-of-the art review on recent research activities in pyrolysis characteristics and kinetics of various microalgae. Common kinetic models predicting the thermal degradation of microalgae are examined and their pros and cons are illustrated. Copyright © 2017 Elsevier Ltd. All rights reserved.

A Combined Raman Spectroscopic and Thermogravimetric Analysis Study on Oxidation of Coal with Different Ranks

Directory of Open Access Journals (Sweden)

Weiqing Zhang

2015-01-01

Full Text Available Raman spectroscopy and nonisothermal thermogravimetric analysis (TGA measurements have been reported for different rank coals (lignite, bituminous coal, and anthracite and the relationship between the measurements was examined. It was found that the Raman spectra parameters can be used to characterize structure changes in the different rank coals, such as the band area ratios based on the curve-fitted results. Higher ranked coal was found to have higher values of IGR/IAll and IG+GR/IAll but lower values of ID/I(G+GR, IDL/I(G+GR, IS+SL/I(G+GR, and I(GL+GL'/I(G+GR. The oxidation properties of the coal samples were characterized by the reactivity indexes Tig, T20%, and Tmax from TGA data which were found to correlate well with the band area ratios of IGR/IAll, IG+GR/IAll, and IS+SL/I(G+GR. Based on these correlations, the Raman band area ratios were found to correlate with the oxidation activity of coal providing additional structural information which can be used to understand the changes in the TGA measurements.

Thermogravimetric studies of the thermo-oxidative stability of irradiated and unirradiated polyethylene. 2. Combined antioxidants

Energy Technology Data Exchange (ETDEWEB)

Novakovic, L; Gal, O; Markovic, V; Stannett, V T

1985-01-01

In part one of this series the effects of a phenolic, an amine and a thioester antioxidant on the thermo-oxidative stability of irradiated and unirradiated low-density polyethylene was reported. In this paper the effects of combined phenolic and thioester stabilizers are described. Isothermal thermogravimetric analysis was used to study the systems. Pronounced synergism was observed with the induction periods, the time when the initial weight loss begins and the 5% weight loss. At about 50% of each stabilizer increases greater than twofold were observed both with the unirradiated and irradiated polymers. The rate constants for oxygen uptake were decreased. However, the rates of degradation at 5% weight loss fell between the values of the two pure stabilizers with no pronounced synergism in either case. In the absence of oxygen little effect of either antioxidant or their mixtures was observed. The corresponding activation energies were somewhat higher, however, with the irradiated samples containing antioxidants. Dynamic thermogravimetry was used for this study. A kinetic analysis indicated that there were somewhat different modes of degradation at lower- and higher-temperature ranges. (author).

Pyrolysis kinetics of raw and hydrothermally carbonized Karanj (Pongamia pinnata) fruit hulls via thermogravimetric analysis.

Science.gov (United States)

Islam, Md Azharul; Asif, M; Hameed, B H

2015-03-01

The pyrolysis of karanj fruit hulls (KFH) and karanj fruit hull hydrothermal carbonization (KFH-HTC) hydrochar was thermogravimetrically investigated under a nitrogen environment at 5 °C/min, 10 °C/min, and 20 °C/min. The pyrolysis decomposition of KFH biomass was faster than that of KFH-HTC hydrochar because of the high volatility and fixed carbon of KFH biomass. Weight loss percentage was also affected by the heating rates. The kinetic data were evaluated with the Kissinger-Akahira-Sunose and Flynn-Wall-Ozawa methods. The activation energy values obtained with these two methods were 61.06 and 68.53 kJ/mol for KFH biomass and 130.49 and 135.87 kJ/mol for KFH-HTC hydrochar, respectively. The analysis of kinetic process mechanisms was verified with the Coats-Redfern method. KFH-HTC hydrochar may play a potential role in transforming biomass to energy-rich feedstock for thermochemical applications because of its high heating value, high fixed carbon, and low ash and sulfur contents. Copyright © 2014 Elsevier Ltd. All rights reserved.

Thermogravimetric analysis and kinetic modeling of low-transition-temperature mixtures pretreated oil palm empty fruit bunch for possible maximum yield of pyrolysis oil.

Science.gov (United States)

Yiin, Chung Loong; Yusup, Suzana; Quitain, Armando T; Uemura, Yoshimitsu; Sasaki, Mitsuru; Kida, Tetsuya

2018-05-01

The impacts of low-transition-temperature mixtures (LTTMs) pretreatment on thermal decomposition and kinetics of empty fruit bunch (EFB) were investigated by thermogravimetric analysis. EFB was pretreated with the LTTMs under different duration of pretreatment which enabled various degrees of alteration to their structure. The TG-DTG curves showed that LTTMs pretreatment on EFB shifted the temperature and rate of decomposition to higher values. The EFB pretreated with sucrose and choline chloride-based LTTMs had attained the highest mass loss of volatile matter (78.69% and 75.71%) after 18 h of pretreatment. For monosodium glutamate-based LTTMs, the 24 h pretreated EFB had achieved the maximum mass loss (76.1%). Based on the Coats-Redfern integral method, the LTTMs pretreatment led to an increase in activation energy of the thermal decomposition of EFB from 80.00 to 82.82-94.80 kJ/mol. The activation energy was mainly affected by the demineralization and alteration in cellulose crystallinity after LTTMs pretreatment. Copyright © 2018 Elsevier Ltd. All rights reserved.

Investigation of the effects of phase transformations in micro and nano aluminum powders on kinetics of oxidation using thermogravimetric analysis.

Science.gov (United States)

Saceleanu, Florin; Atashin, Sanam; Wen, John Z

2017-07-26

Aluminum micro and nanoparticles are key ingredients in the synthesis of nano energetic materials. Hence it is important to characterize the kinetics and the rate controlling process of their oxidation. The literature shows that the mass diffusion and phase transformation within the aluminum oxide shell are important. However, the description of physical processes regarding simultaneous oxidation and phase transformation is lacking. In this paper, the controlled thermogravimetric (TGA) oxidation of 40-60 nm and 1 µm Al powders is investigated at constant heating rates and under isothermal conditions, respectively, upon varying the partial pressure of oxygen. It is found that the core-shell model of homogenous oxidation is applicable to explain the TGA results when the shell does not undergo phase transformation, which predicts the apparent activation energy in good agreement with the literature data. On the other hand, the simultaneous oxidation and phase transformation is able to be addressed using the JMAK model which reveals key parameters of the rate controlling processes. Mass diffusion is indeed rate determining during the oxidation of Al micro and nanopowders while the kinetics of the reaction is fast. Unlike the micron powders, the particle size distribution has a significant effect on the shape of the oxidation curves of the nanopowders.

Determination of kinetic parameters in the pyrolysis operation and thermal behavior of Prosopis juliflora using thermogravimetric analysis.

Science.gov (United States)

Chandrasekaran, Arunkumar; Ramachandran, Sethumadhavan; Subbiah, Senthilmurugan

2017-06-01

This paper deals with the pyrolysis of Prosopis juliflora fuelwood using thermogravimetric analysis to determine the kinetic parameters at six different heating rates of 2, 5, 10, 15, 20 and 25°C/min. The activation energy of pyrolysis was calculated using different methods, namely Kissinger, Kissinger-Akahira-Sunose, Ozawa-Flynn-Wall and Friedman model and corresponding calculated activation energy were found to be 164.6, 204, 203.2, and 219.3kJ/mol, respectively for each method. The three-pseudo component model was applied to calculate the following three kinetic parameters: activation energy, pre-exponential factor and order of reaction. The experimental results were validated with model prediction for all the six heating rates. The three-pseudo component model is able to predict experimental results much accurately while considering variable order reaction model (n≠1). Copyright © 2017 Elsevier Ltd. All rights reserved.

Thermogravimetric Characterization of the Microstructui Composition of Polyamide Injection Molded Denture Base Material vs Conventional Compression Molded Heat-cured Denture Base Material.

Science.gov (United States)

Al-Dharrab, Ayman; Shinawi, Lana

2016-02-01

Thermoplastic resin polymers are widely used in medicine due to their biostability and hypoallergenic properties, making them a possible alternative to poly-methylmethacrylate (PMMA). The current research examined the microstructure of a rapid injection molding system thermoplastic resin for construction of flexible denture compared with that of heat-cured PMMA. A total of 40 disk-shaped specimens (25 mm in diameter and 3 mm in thickness) were prepared and divided into two groups of 20 disks each (group I samples were of thermoplastic acrylic resin while group II was heat-cured PMMA resin). In group I, thermogravimetric analyzer showed that increasing the temperature up to 169°C resulted in about 1.3% of the material loss, and after that the material remains thermally stable up to 200°C. Group 11 showed 2.24% weight loss at 171°C, and further weight loss (12.025%) was observed on heating to 230°C. Fourier transform infrared (FTIR) spectrophotometer analysis in the range of 400-4000 cm(-1) detected the presence of an amine group (N-H) in group I samples and the presence of methylene group attached to inorganic Si as reinforcement filler (Si-CH3). Thermoplastic resin displayed excellent thermal stability and the absence of residual monomer within the polymerized material, suggesting its suitability for the fabrication dentures.

A thermogravimetric analysis (TGA) method developed for estimating the stoichiometric ratio of solid-state {alpha}-cyclodextrin-based inclusion complexes

Energy Technology Data Exchange (ETDEWEB)

Bai, Yuxiang; Wang, Jinpeng; Bashari, Mohanad; Hu, Xiuting [The State Key Laboratory of Food Science and Technology, School of Food Science and Technology, Jiangnan University, Wuxi 214122 (China); Feng, Tao [School of Perfume and Aroma Technology, Shanghai Institute of Technology, Shanghai 201418 (China); Xu, Xueming [The State Key Laboratory of Food Science and Technology, School of Food Science and Technology, Jiangnan University, Wuxi 214122 (China); Jin, Zhengyu, E-mail: jinlab2008@yahoo.com [The State Key Laboratory of Food Science and Technology, School of Food Science and Technology, Jiangnan University, Wuxi 214122 (China); Tian, Yaoqi, E-mail: yqtian@jiangnan.edu.cn [The State Key Laboratory of Food Science and Technology, School of Food Science and Technology, Jiangnan University, Wuxi 214122 (China)

2012-08-10

Highlights: Black-Right-Pointing-Pointer We develop a TGA method for the measurement of the stoichiometric ratio. Black-Right-Pointing-Pointer A series of formulas are deduced to calculate the stoichiometric ratio. Black-Right-Pointing-Pointer Four {alpha}-CD-based inclusion complexes were successfully prepared. Black-Right-Pointing-Pointer The developed method is applicable. - Abstract: An approach mainly based on thermogravimetric analysis (TGA) was developed to evaluate the stoichiometric ratio (SR, guest to host) of the guest-{alpha}-cyclodextrin (Guest-{alpha}-CD) inclusion complexes (4-cresol-{alpha}-CD, benzyl alcohol-{alpha}-CD, ferrocene-{alpha}-CD and decanoic acid-{alpha}-CD). The present data obtained from Fourier transform-infrared (FT-IR) spectroscopy showed that all the {alpha}-CD-based inclusion complexes were successfully prepared in a solid-state form. The stoichiometric ratios of {alpha}-CD to the relative guests (4-cresol, benzyl alcohol, ferrocene and decanoic acid) determined by the developed method were 1:1, 1:2, 2:1 and 1:2, respectively. These SR data were well demonstrated by the previously reported X-ray diffraction (XRD) method and the NMR confirmatory experiments, except the SR of decanoic acid with a larger size and longer chain was not consistent. It is, therefore, suggested that the TGA-based method is applicable to follow the stoichiometric ratio of the polycrystalline {alpha}-CD-based inclusion complexes with smaller and shorter chain guests.

A thermogravimetric analysis (TGA) method developed for estimating the stoichiometric ratio of solid-state α-cyclodextrin-based inclusion complexes

International Nuclear Information System (INIS)

Bai, Yuxiang; Wang, Jinpeng; Bashari, Mohanad; Hu, Xiuting; Feng, Tao; Xu, Xueming; Jin, Zhengyu; Tian, Yaoqi

2012-01-01

Highlights: ► We develop a TGA method for the measurement of the stoichiometric ratio. ► A series of formulas are deduced to calculate the stoichiometric ratio. ► Four α-CD-based inclusion complexes were successfully prepared. ► The developed method is applicable. - Abstract: An approach mainly based on thermogravimetric analysis (TGA) was developed to evaluate the stoichiometric ratio (SR, guest to host) of the guest–α-cyclodextrin (Guest-α-CD) inclusion complexes (4-cresol-α-CD, benzyl alcohol-α-CD, ferrocene-α-CD and decanoic acid-α-CD). The present data obtained from Fourier transform-infrared (FT-IR) spectroscopy showed that all the α-CD-based inclusion complexes were successfully prepared in a solid-state form. The stoichiometric ratios of α-CD to the relative guests (4-cresol, benzyl alcohol, ferrocene and decanoic acid) determined by the developed method were 1:1, 1:2, 2:1 and 1:2, respectively. These SR data were well demonstrated by the previously reported X-ray diffraction (XRD) method and the NMR confirmatory experiments, except the SR of decanoic acid with a larger size and longer chain was not consistent. It is, therefore, suggested that the TGA-based method is applicable to follow the stoichiometric ratio of the polycrystalline α-CD-based inclusion complexes with smaller and shorter chain guests.

Determination of activation energy for animal fat and crude glycerol using thermogravimetric analysis

Energy Technology Data Exchange (ETDEWEB)

Koch, Crhristoph [University of Hannover, Hannover (Germany); Mortari, Daniela; Avila, Ivonete; Santos, Antonio Moreira dos; Silva, Mario Lucio Cristovam; Crnkovic, Paula Manoel [University of Sao Paulo, Sao Carlos, SP (Brazil)], e-mails: iavila@sc.usp.br, asantos@sc.usp.br, paulam@sc.usp.br

2010-07-01

The present study deals with the determination of the activation energy of animal fat and crude glycerol from a biodiesel production plant. The activation energies were investigated by thermogravimetric analysis in the temperature range of {delta}T = 25-600 deg C. The transient experiments were run for every sample (10 mg) at five different heating rates (2.5, 5.0, 10.0, 20.0 and 30.0 deg C/min) in atmosphere of synthetic air. It is possible to establish a direct relation between the activation energy and the ignition delay, which characterizes the combustion quality of a fuel. The activation energy could be determined as a function of the conversion degree and the temperature by the isoconversional model free kinetics. Four distinct phases were found for each sample and one of these phases was identified as low-temperature oxidation (LTO). As this region is responsible for the first vaporization of the fuel, the activation energies were determined for this special region along the whole conversion range (0 - 100 %). The following mean values could be determined: animal fat = 108.87 +- 52.28 kJ/mol, and crude glycerol = 65.37+- 13.17 kJ/mol. From these data, it was possible to conclude that animal fat is the most complex sample between the ones studied in this work (author)

The oxygen potential of near- and non-stoichiometric urania-25 mol% plutonia solid solutions: a comparison of thermogravimetric and galavanic cell measurements

International Nuclear Information System (INIS)

Woodley, R.E.; Adamson, M.G.

1979-01-01

To resolve discrepancies between the existing low temperature ΔGsub(0 2 )(mean) data for solid solution mixed (U, Pu)-oxide nuclear fuel material, additional measurements have been performed on Usub(0.75)Pusub(0.25) employing a combined thermogravimetric (TGA) and solid-electrolyte galvanic cell technique. These measurements, which were performed at temperatures between 800 and 1000 0 C, and for O:M ratios in the range 1.940 to 2.028, are reasonably self-consistent and show good agreement with the results of previous TGA measurements. However, they do not corroborate the earlier EMF cell measurements of Markin and McIver. (1967). Possible explanations for errors in these earlier EMF cell results are examined. The new results indicate that the ΔGsub(O 2 )(mean) of stoichiometric mixed oxide at typical outer surface fuel temperature is close to -100 kcal/mol 0 2 (-419 kJ/mol O 2 ). Attempts have been made to fit the new ΔGsub(O 2 )(mean) data to two equations derived from recent defect models, and it is shown that neither equation accurately represents the experimental psub(O 2 ) - x data over more than a short range of x. (Auth.)

Graft copolymerization and characterization of styrene with chitosan ...

African Journals Online (AJOL)

Fourier transform infrared spectroscopy (FTIR) results showed the presence of polystyrene peaks, indicating the success of the grafting procedure. Thermogravimetric analyses (TGA) revealed that the thermal stability of the prepared copolymer is higher than that of chitosan alone. Mw and Mn of the isolated polystyrene from ...

Synthesis and characterization of PMMA/silylated MMTs

International Nuclear Information System (INIS)

De Maria, A.; Aurora, A.; Montone, A.; Tapfer, L.; Pesce, E.; Balboni, R.; Schwarz, M.; Borriello, C.

2011-01-01

Commercially available Sodium clay (Dellite HPS) and organo-clay (Dellite 72T) are modified via a silylation reaction. These silylated clays are characterized by IR, XRD, thermogravimetric analyses, and their equilibrium contact angles are measured. They are used to prepare nanocomposites at different loading percentage (1, 3, 5% wt) by in situ intercalative polymerization of Methyl methacrylate and morphology and thermal properties of nanocomposites are examined. SEM images of nanocomposites fractured surface show the absence of clays aggregates, confirming a good dispersion and distribution of montmorillonites in the polymer matrix. The effects of modified clays on the thermal properties of nanocomposites are analyzed by differential scanning calorimetry and thermogravimetric analyses showing an increase of glass and decomposition temperatures of all nanocomposites respect to homopolymer ones. The best results are obtained in the presence of silylated montmorillonites, clearly the organosilane improves the compatibility between polymer matrix and clay and as effect the properties of nanocomposites.

INFLUENCE OF BIOPRETREATMENT ON THE CHARACTER OF CORN STOVER LIGNIN AS SHOWN BY THERMOGRAVIMETRIC AND CHEMICAL STRUCTURAL ANALYSES

OpenAIRE

Xuewei Yang; Yelin Zeng; Xiaoyu Zhang

2010-01-01

The effect of corn stover lignin structure alteration caused by white-rot fungi pretreatment on the pyrolysis kinetics was studied by FTIR and TG/DTA. Results showed that biopretreatment had a remarkable effect on lignin pyrolysis. Biopretreatment can decrease the activation energy and increase the pre-exponential factor in the initial stage of pyrolysis, which makes it possible to start the lignin pyrolysis at a relatively gentle condition and improve the availability of biomass pyrolysis as...

Investigation of thermodynamic parameters in the pyrolysis conversion of biomass and manure to biochars using thermogravimetric analysis.

Science.gov (United States)

Xu, Yiliang; Chen, Baoliang

2013-10-01

The thermodynamic parameters of the conversion of two companion pair materials, i.e., rice straw vs dairy manure, and rice bran vs chicken manure, to biochars were characterized by thermogravimetric analysis. The overall changes of activation energy (Ea) were well described by the Flynn-Wall method. The Ea values increased steeply from about 120 to 180 kJ/mol at the mass conversion (α) at 0.2-0.4, followed by a relatively steady change at 0.40.65. The higher contents of minerals in manures resulted in the larger Ea. The individual conversion of hemicellulose, cellulose and lignin in the feedstocks was identified and their thermodynamic parameters (ΔH°, ΔG° and ΔS°) were calculated. The yields of biochars calculated from TG curve were compared with the determined yields of biochars using muffle pyrolysis. Along with Fourier transform infrared spectra data, the distinct decompositions of biomasses and manures were evaluated. Copyright © 2013 Elsevier Ltd. All rights reserved.

New sample carrier systems for thermogravimetric analysis under forced flow conditions and their influence on microkinetic results.

Science.gov (United States)

Seibel, C; Fieback, T M

2015-09-01

For thermogravimetric analysis, it has been shown that, depending on the type of sample container, different kinetic results could be obtained despite regarding the same reaction under constant conditions. This is due to limiting macrokinetic effects which are strongly dependant on the type of sample carrying system. This prompted the need for sample containers which deliver results minimally limited by diffusive mass transport. In this way, two container systems were developed, both characterized by a forced flow stream through a solid, porous bed: one from bottom to top (counter-current flow) and one from top to bottom (co-current flow). Optical test measurements were performed, the results indicating that reaction proceedings are almost fully independent of the geometrical shape of the sample containers. The Boudouard reaction was investigated with a standard crucible and the new developed systems; the reaction rates determined differed significantly, up to a factor of 6.2 at 1373 K.

THERMOGRAVIMETRIC INVESTIGATION AND THERMAL CONVERSION KINETICS OF TYPICAL NORTH-AFRICA AND MIDDLE-EAST LIGNOCELLULOSIC WASTES

Directory of Open Access Journals (Sweden)

2012-01-01

Full Text Available The aim of this work was to thermally characterize the renewable lignocellulosic bioresources derived from palm trees in order to highlight their energy potential. Pyrolysis and combustion behaviours of date stones (DS agricultural by-products were tested by thermo-gravimetric analysis, and the main chemical compositions were analyzed. The work has also been conducted to identify their most important physical characteristics. The study of the sizes and heating rate effects constitute the first part of the experimental work. Inert atmosphere and three heating rates: 10, 20, and 50 °C/min, were applied to various particle sizes of DS. In the second part, tests were carried out in an oxidizing atmosphere (21% O2 by varying the size of the DS. The kinetic parameters such as pre-exponential factor and activation energy were determined. Increasing the particle sizes and the heating rates didn’t have an appreciable influence on the global weight losses. However, degradation rates were significant with the porous structure of the DS. Weight losses in inert and oxidizing atmospheres were found to occur in two stages (drying and devolatilization and in three stages (drying, devolatilization, and oxidation of the char.

A Combined Raman Spectroscopic and Thermogravimetric Analysis Study on Oxidation of Coal with Different Ranks.

Science.gov (United States)

Zhang, Weiqing; Jiang, Shuguang; Hardacre, Christopher; Goodrich, Peter; Wang, Kai; Shao, Hao; Wu, Zhengyan

2015-01-01

Raman spectroscopy and nonisothermal thermogravimetric analysis (TGA) measurements have been reported for different rank coals (lignite, bituminous coal, and anthracite) and the relationship between the measurements was examined. It was found that the Raman spectra parameters can be used to characterize structure changes in the different rank coals, such as the band area ratios based on the curve-fitted results. Higher ranked coal was found to have higher values of I GR/I All and I (G + GR)/I All but lower values of I D/I (G+GR), I DL/I (G+GR), I (S + SL)/I (G+GR), and I (GL+GL')/I (G+GR). The oxidation properties of the coal samples were characterized by the reactivity indexes T ig, T 20%, and T max from TGA data which were found to correlate well with the band area ratios of I GR/I All, I (G + GR)/I All, and I (S + SL)/I (G+GR). Based on these correlations, the Raman band area ratios were found to correlate with the oxidation activity of coal providing additional structural information which can be used to understand the changes in the TGA measurements.

Vaporization enthalpies of imidazolium based ionic liquids. A thermogravimetric study of the alkyl chain length dependence

International Nuclear Information System (INIS)

Verevkin, Sergey P.; Zaitsau, Dzmitry H.; Emel’yanenko, Vladimir N.; Ralys, Ricardas V.; Yermalayeu, Andrei V.; Schick, Christoph

2012-01-01

Highlights: ► Enthalpies of vaporization of ionic liquids were measured with thermogravimetry. ► We studied 1-alkyl-3-methyl-imidazolium bis(trifluoromethanesulfonyl)imide. ► The linear alkyl chain length was 4, 6, 8, 10, 12, 14, 16, and 18 C-atoms. ► A linear dependence on the chain length of the alkyl-imidazolium cation was found. - Abstract: Vaporization enthalpies for a series of ten ionic liquids (ILs) 1-alkyl-3-methyl-imidazolium bis(trifluoromethanesulfonyl)imide [C n mim][NTf 2 ], with the alkyl chain length n = 4, 6, 8, 10, 12, 14, 16, and 18 were determined using the thermogravimetric method. An internally consistent set of experimental data and vaporization enthalpies at 540 K was obtained. Vaporization enthalpies at 540 K have shown a linear dependence on the chain length of the alkyl-imidazolium cation in agreement with the experimental results measured previously with a quartz crystal microbalance. Ambiguity of Δ l g C pm o -values required for the extrapolation of experimental vaporization enthalpies to the reference temperature 298 K has been discussed.

Effect of biopretreatment on thermogravimetric and chemical characteristics of corn stover by different white-rot fungi.

Science.gov (United States)

Yang, Xuewei; Zeng, Yelin; Ma, Fuying; Zhang, Xiaoyu; Yu, Hongbo

2010-07-01

The thermogravimetric and chemical characterization of corn stover biopretreated by three different species of white-rot fungi have been studied in this research. Results indicated that biopretreatment can optimize the thermal decomposition, decrease the reaction temperature and reduce the gas contamination (SO(x)), making the biomass pyrolysis more efficient and environmentally friendly. Biopretreatment can decrease the activation energy and reacting temperature of the hemicellulose and cellulose pyrolysis (up to 36 degrees C), shorten the temperature range of the active pyrolysis (up to 14 degrees C), and increase the thermal decomposition rate, greatly promoting the reaction and making the biomass pyrolysis easier to start and carry on. On the other hand, by biopretreatment, the sulphur content can decrease up to 46.15%, which can considerably reduce the inventory of SO(x) emission. Moreover, the mechanism of the biopretreatment was also explored that the deconstruction and depolymerization of the recalcitrant linkages of lignin and cellulose by biopretreatment can make the structure of biomass incompact and easier to be pyrolyzed. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Effect of biodegradation on thermogravimetric and chemical characteristics of hardwood and softwood by brown-rot fungus.

Science.gov (United States)

Gao, Zhenzhong; Fan, Qi; He, Zesen; Wang, Zhinan; Wang, Xiaobo; Sun, Jin

2016-07-01

The thermogravimetric and chemical characterization of hardwood Eucalyptus urophylla (Ep) and softwood Pinus massoniana (Mp) pretreated by brown-rot fungus Gloeophyllum trabeum were investigated. The results indicated that the brown-rot fungus pretreatment can optimize the thermal decomposition and decrease the initiation temperatures (8-11°C lower) of both the Ep and Mp pyrolysis. The mean activation energy values of the bio-treated samples were 29.7kJ/mol (for Ep) and 42.3kJ/mol (for Mp) lower than that of the un-treated samples at the conversion rate from 0.1 to 0.7 based on Flynn-Wall-Ozawa (FWO) method. After the bio-pretreatment, the required temperatures were lower (4-7°C) for the pyrolysis rates of hemicellulose and cellulose in Mp reaching maximum and termination. However, the situation was just the opposite for Ep. The variations in chemical properties of hydrogen bonding, as well as the relative changes in lignin/carbohydrate composition of both wood species were also examined. Copyright © 2016 Elsevier Ltd. All rights reserved.

Synthesis, characterization and antimicrobial activity of some ...

African Journals Online (AJOL)

Thermogravimetric analyses were also carried out. The data obtained agree with the proposed structures and show that the complexes decomposed to the corresponding metal oxide. The ligand and their metal complexes were screened for their antimicrobial activities by the agar-well diffusion technique using DMSO as a ...

Effects of additives on the co-pyrolysis of municipal solid waste and paper sludge by using thermogravimetric analysis.

Science.gov (United States)

Fang, Shiwen; Yu, Zhaosheng; Lin, Yan; Lin, Yousheng; Fan, Yunlong; Liao, Yanfen; Ma, Xiaoqian

2016-06-01

By using thermogravimetric analysis (TGA), the effects of different additives (MgO, Al2O3 and ZnO) on the pyrolysis characteristics and activation energy of municipal solid waste (MSW), paper sludge (PS) and their blends in N2 atmosphere had been investigated in this study. The experiments resulted that these additives were effective in reducing the initial temperature and activation energy. However, not all the additives were beneficial to reduce the residue mass and enhance the index D. For the different ratios of MSW and PS, the same additive even had the different influences. The catalytic effects of additives were not obvious and the pyrolysis became difficult with the increase of the proportion of PS. Based on all the contrast of the pyrolysis characteristics, MgO was the best additive and 70M30P was the best ratio, respectively. Copyright © 2016 Elsevier Ltd. All rights reserved.

Thermogravimetric and Magnetic Studies of the Oxidation and Reduction Reaction of SmCoO3 to Nanostructured Sm2O3 and Co

Science.gov (United States)

Kelly, Brian; Cichocki, Ronald; Poirier, Gerald; Unruh, Karl

The SmCoO3 to nanostructured Sm2O3 and Co oxidation and reduction reaction has been studied by thermogravimetric analysis (TGA) measurements in forming gas (FG) and inert N2 atmospheres, x-ray diffraction (XRD) and vibrating sample magnetometry (VSM). The TGA measurements showed two clearly resolvable reduction processes when heating in FG, from the initial SmCoO3 phase through an intermediate nanostructured mixture of Sm2O3 and CoO when heated to 330°C for several minutes, and then the conversion of CoO to metallic Co when heated above 500°C. These phases were confirmed by XRD and VSM. Similar measurements in N2 yielded little mass change below 900°C and coupled reduction processes at higher temperatures. Isoconversional measurements of the CoO to Co reduction reaction in FG yielded activation energies above 2eV/atom in the nanostructured system. This value is several times larger than those reported in the literature or obtained by similar measurements of bulk mixtures of Sm2O3 and CoO, suggesting the nanostructuring was the source of the large increase in activation energy.

Thermogravimetric measurement of hydrogen storage in carbon-based materials: promise and pitfalls

International Nuclear Information System (INIS)

Pinkerton, F.E.; Wicke, B.G.; Olk, C.H.; Tibbetts, G.G.; Meisner, G.P.; Meyer, M.S.; Herbst, J.F.

2000-01-01

We have used a thermogravimetric analyzer (TGA) to measure the hydrogen absorption capacity of a variety of carbon-based storage materials, including Li- and K-intercalated graphite and Li-doped multi-wall nanotubes. The TGA uses weight gain/loss as a function of time and temperature to monitor hydrogen absorption/desorption in flowing hydrogen gas. Creating and maintaining a contaminant-free atmosphere is critical to the accurate TGA measurement of hydrogen absorption in carbon-based materials; even low concentrations of impurity gases such as O 2 or H 2 O are sufficient to masquerade as hydrogen absorption. We will discuss examples of this effect relevant to recent reports of hydrogen storage appearing in the literature. The precautions required are non-trivial. In our TGA, for instance, about 16% of the original atmosphere remains after a two-hour purge; at least 15 hours is required to fully purge the apparatus. Furthermore, we cover the TGA with a protective atmosphere enclosure during sample loading to minimize the introduction of impurity gases. With these precautions it is possible to unambiguously measure hydrogen storage. For example, we have determined the hydrogen absorption capacity of our K-intercalated graphite samples to be 1.3 wt% total hydrogen absorption above 50 o C, of which 0.2 wt% can be reproducibly recovered with temperature cycling. With due care, TGA measurements provide complementary information to that obtained from standard pressure techniques for measuring hydrogen sorption, which rely on measuring the loss of gas pressure in a known volume. Taken together, TGA and pressure measurements provide a powerful combination for determining verifiable hydrogen storage capacity. (author)

Full in-vitro analyses of new-generation bulk fill dental composites cured by halogen light.

Science.gov (United States)

Tekin, Tuçe Hazal; Kantürk Figen, Aysel; Yılmaz Atalı, Pınar; Coşkuner Filiz, Bilge; Pişkin, Mehmet Burçin

2017-08-01

The objective of this study was to investigate the full in-vitro analyses of new-generation bulk-fill dental composites cured by halogen light (HLG). Two types' four composites were studied: Surefill SDR (SDR) and Xtra Base (XB) as bulk-fill flowable materials; QuixFill (QF) and XtraFill (XF) as packable bulk-fill materials. Samples were prepared for each analysis and test by applying the same procedure, but with different diameters and thicknesses appropriate to the analysis and test requirements. Thermal properties were determined by thermogravimetric analysis (TG/DTG) and differential scanning calorimetry (DSC) analysis; the Vickers microhardness (VHN) was measured after 1, 7, 15 and 30days of storage in water. The degree of conversion values for the materials (DC, %) were immediately measured using near-infrared spectroscopy (FT-IR). The surface morphology of the composites was investigated by scanning electron microscopes (SEM) and atomic-force microscopy (AFM) analyses. The sorption and solubility measurements were also performed after 1, 7, 15 and 30days of storage in water. In addition to his, the data were statistically analyzed using one-way analysis of variance, and both the Newman Keuls and Tukey multiple comparison tests. The statistical significance level was established at pfill, resin-based dental composites. Copyright © 2017 Elsevier B.V. All rights reserved.

Thermogravimetric Analysis (TGA) Profile of Modified Sba-15 at Different Amount of Alkoxy silane Group

International Nuclear Information System (INIS)

Norhasyimi Rahmat; Nur Fathilah Mohd Yusof; Ezani Hafiza

2014-01-01

This study focused on meso porous silica SBA-15 modified with alkoxy silane functional group; phenyltriethoxysilane (PTES) and vinyltriethoxysilane (VTES) using direct synthesis and post-grafting methods. By direct synthesis method, SBA-15 template by triblock copolymer (P123) and functionalized with alkoxy silane groups at different amount of loadings were co-condensed with tetraethyl orthosilicate (TEOS) under acidic conditions. As for post-grafting method, different loadings of alkoxy silane groups were added after co-condensation of TEOS with P123 template. Both synthesis methods used calcination process to remove surfactant template at 550 degree Celsius for 5 hours. The derivatized SBA-15 was characterized by thermogravimetric analysis to evaluate the profile at different loadings of alkoxy silane groups with different synthesis method. At temperature range of 300-800 degree Celsius, post-grafting method displayed the highest weight loss of phenyl and vinyl groups. However, there was no significant difference of weight loss for different amount of organo silane groups. In this study, TGA has shown to be significant characterization means to determine the effects of different method used in synthesizing modified SBA-15. It was shown that different loading of phenyl and vinyl groups did not affect the efficiency of surfactant removal. (author)

Thermogravimetric analysis of rice and wheat straw catalytic combustion in air- and oxygen-enriched atmospheres

International Nuclear Information System (INIS)

Yu Zhaosheng; Ma Xiaoqian; Liu Ao

2009-01-01

By thermogravimetric analysis (TGA) study, the influences of different catalysts on the ignition and combustion of rice and wheat straw in air- and oxygen-enriched atmospheres have been investigated in this paper. Straw combustion is divided into two stages. One is the emission and combustion of volatiles and the second is the combustion of fixed carbon. The existence of catalysts in the first step enhances the emission of volatiles from the straw. The action of catalysts in the second step of straw combustion may be as a carrier of oxygen to the fixed carbon. Two parameters have been used to compare the characteristics of ignition and combustion of straw under different catalysts and in various oxygen concentrations. One is the temperature when the conversion degree combustible (CDC) of straw is 5%, the other is the CDC when the temperature is 900 deg. C. By comparing the different values of the two parameters, the different influences of the catalysts and oxygen concentration on the ignition and combustion of straw have been studied, the action of these catalysts for straw ignition and combustion in air and oxygen-enriched atmosphere is effective except the oxygen-enriched catalytic combustion of wheat straw fixed carbon

Sedimentation technique of waste bituminization and thermogravimetric characteristics of the finalproducts

International Nuclear Information System (INIS)

Zeger, J.; Knotik, K.

1976-01-01

In the research centre of the Oesterreichische Studiengesellschaft fuer Atomenergie GesmbH a semitechnical plant has been installed for waste bituminization, which has been tested inactively since 1973. This plant is using a new technological process for embedding. One of the important features of this new process is that the, normally inactive solution water is distilled off prior to the embedding, resulting in dry and powdery salts. The second important feature is that the mixing of these dry salts with the thin fluid bitumen is done by sedimentation. Expecially there is no mechanical aid used for mixing. Thermogravimetric analysis of samples which simulated the final products of this pilot plant, were carried out to verify the best working parameters and to study the possible chemical damage to the bitumen. Analysis was performed by heating the samples, consisting of various mixtures of bitumen and inorganic salts, in a METTLER-Thermoanalyzer up to 500 0 C using different atmospheres (air, nitrogen). It could be shown that only nitrate and nitrite especially in combination with Fe(III)-ions are of negative influence on the thermostability of bitumen. They lead to a sudden and quick weight loss of the samples between 370 and 410 0 C (above the melting point of both NaNO 2 and NaNO 3 ). The Fe-ions hava a catalytic influence, as it could be shown that 1 1% addiation of Fe(NO 3 ) 3 to NaNO 3 leads to a considerable acceleration of the incineration. This influence of the Fe(III)-ion can be suppressed to some extend by a hydrolysis prior to the embedding. In preparation of further studies concerning the behaviour of radiation damaged bitumen there has been developed a method of measuring the dose rate of an unknown radioactive salt mixture at any point of this mixture. This is done by making two measurements with glass dosimeters. One with a beta-absorber to get a pure gamma-dose and the other without it to get the combined beta and gamma dose. (author)

Chemometric modeling of thermogravimetric data for the compositional analysis of forest biomass.

Science.gov (United States)

Acquah, Gifty E; Via, Brian K; Fasina, Oladiran O; Adhikari, Sushil; Billor, Nedret; Eckhardt, Lori G

2017-01-01

The objective of this study was to investigated the use of chemometric modeling of thermogravimetric (TG) data as an alternative approach to estimate the chemical and proximate (i.e. volatile matter, fixed carbon and ash contents) composition of lignocellulosic biomass. Since these properties affect the conversion pathway, processing costs, yield and / or quality of products, a capability to rapidly determine these for biomass feedstock entering the process stream will be useful in the success and efficiency of bioconversion technologies. The 38-minute long methodology developed in this study enabled the simultaneous prediction of both the chemical and proximate properties of forest-derived biomass from the same TG data. Conventionally, two separate experiments had to be conducted to obtain such information. In addition, the chemometric models constructed with normalized TG data outperformed models developed via the traditional deconvolution of TG data. PLS and PCR models were especially robust in predicting the volatile matter (R2-0.92; RPD- 3.58) and lignin (R2-0.82; RPD- 2.40) contents of the biomass. The application of chemometrics to TG data also made it possible to predict some monomeric sugars in this study. Elucidation of PC loadings obtained from chemometric models also provided some insights into the thermal decomposition behavior of the chemical constituents of lignocellulosic biomass. For instance, similar loadings were noted for volatile matter and cellulose, and for fixed carbon and lignin. The findings indicate that common latent variables are shared between these chemical and thermal reactivity properties. Results from this study buttresses literature that have reported that the less thermally stable polysaccharides are responsible for the yield of volatiles whereas the more recalcitrant lignin with its higher percentage of elementary carbon contributes to the yield of fixed carbon.

Chemometric modeling of thermogravimetric data for the compositional analysis of forest biomass.

Directory of Open Access Journals (Sweden)

Gifty E Acquah

Full Text Available The objective of this study was to investigated the use of chemometric modeling of thermogravimetric (TG data as an alternative approach to estimate the chemical and proximate (i.e. volatile matter, fixed carbon and ash contents composition of lignocellulosic biomass. Since these properties affect the conversion pathway, processing costs, yield and / or quality of products, a capability to rapidly determine these for biomass feedstock entering the process stream will be useful in the success and efficiency of bioconversion technologies. The 38-minute long methodology developed in this study enabled the simultaneous prediction of both the chemical and proximate properties of forest-derived biomass from the same TG data. Conventionally, two separate experiments had to be conducted to obtain such information. In addition, the chemometric models constructed with normalized TG data outperformed models developed via the traditional deconvolution of TG data. PLS and PCR models were especially robust in predicting the volatile matter (R2-0.92; RPD- 3.58 and lignin (R2-0.82; RPD- 2.40 contents of the biomass. The application of chemometrics to TG data also made it possible to predict some monomeric sugars in this study. Elucidation of PC loadings obtained from chemometric models also provided some insights into the thermal decomposition behavior of the chemical constituents of lignocellulosic biomass. For instance, similar loadings were noted for volatile matter and cellulose, and for fixed carbon and lignin. The findings indicate that common latent variables are shared between these chemical and thermal reactivity properties. Results from this study buttresses literature that have reported that the less thermally stable polysaccharides are responsible for the yield of volatiles whereas the more recalcitrant lignin with its higher percentage of elementary carbon contributes to the yield of fixed carbon.

Dairy shows different associations with abdominal and BMI-defined overweight: Cross-sectional analyses exploring a variety of dairy products.

Science.gov (United States)

Brouwer-Brolsma, E M; Sluik, D; Singh-Povel, C M; Feskens, E J M

2018-05-01

Previous studies have suggested weight-regulatory properties for several dairy nutrients, but population-based studies on dairy and body weight are inconclusive. We explored cross-sectional associations between dairy consumption and indicators of overweight. We included 114,682 Dutch adults, aged ≥18 years. Dairy consumption was quantified by a food frequency questionnaire. Abdominal overweight was defined as waist circumference (WC) ≥88 cm (women) or ≥102 cm (men) (n = 37,391), overweight as BMI ≥25-30 kg/m 2 (n = 44,772) and obesity as BMI ≥30 kg/m 2 (n = 15,339). Associations were quantified by logistic (abdominal overweight, no/yes), multinomial logistic (BMI-defined overweight and obesity) and linear regression analyses (continuous measures of WC and BMI), and they were adjusted for relevant covariates. Total dairy showed a positive association with abdominal overweight (OR Q1 ref vs. Q5: 1.09; 95% CI: 1.04-1.14) and with BMI-defined overweight (OR Q5 1.13; 95% CI: 1.08-1.18) and obesity (OR Q5 1.09; 95% CI: 1.02-1.16). Skimmed, semi-skimmed and non-fermented dairy also showed positive associations with overweight categories. Full-fat dairy showed an inverse association with overweight and obesity (OR Q5 for obesity: 0.78; 95% CI: 0.73-0.83). Moreover, inverse associations were observed for yoghurt and custard and positive associations for milk, buttermilk, flavoured yoghurt drinks, cheese and cheese snacks. Fermented dairy, curd cheese and Dutch cheese did not show a consistent association with overweight categories. Total, skimmed, semi-skimmed and non-fermented dairy; milk; buttermilk; flavoured yoghurt drinks; total cheese and cheese snacks showed a positive association with overweight categories, whereas full-fat dairy, custard and yoghurt showed an inverse association with overweight categories. Copyright © 2018 The Italian Society of Diabetology, the Italian Society for the Study of Atherosclerosis, the Italian Society of Human

A thermogravimetric analysis (TGA) method to determine the catalytic conversion of cellulose from carbon-supported hydrogenolysis process

International Nuclear Information System (INIS)

Leal, Glauco F.; Ramos, Luiz A.; Barrett, Dean H.; Curvelo, Antonio Aprígio S.; Rodella, Cristiane B.

2015-01-01

Graphical abstract: - Highlights: • A new method to determine the catalytic conversion of cellulose using TGA has been developed. • TGA is able to differentiate between carbon from cellulose and carbon from the catalyst. • Building an analytical curve from TGA results enables the accurate determination of cellulose conversion. - Abstract: The ability to determine the quantity of solid reactant that has been transformed after a catalytic reaction is fundamental in accurately defining the conversion of the catalyst. This quantity is also central when investigating the recyclability of a solid catalyst as well as process control in an industrial catalytic application. However, when using carbon-supported catalysts for the conversion of cellulose this value is difficult to obtain using only a gravimetric method. The difficulty lies in weighing errors caused by loss of the solid mixture (catalyst and non-converted cellulose) after the reaction and/or moisture adsorption by the substrate. These errors are then propagated into the conversion calculation giving erroneous results. Thus, a quantitative method using thermogravimetric analysis (TGA) has been developed to determine the quantity of cellulose after a catalytic reaction by using a tungsten carbide catalyst supported on activated carbon. Stepped separation of TGA curves was used for quantitative analysis where three thermal events were identified: moisture loss, cellulose decomposition and CO/CO 2 formation. An analytical curve was derived and applied to quantify the residual cellulose after catalytic reactions which were performed at various temperatures and reaction times. The catalytic conversion was calculated and compared to the standard gravimetric method. Results showed that catalytic cellulose conversion can be determined using TGA and exhibits lower uncertainty (±2%) when compared to gravimetric determination (±5%). Therefore, it is a simple and relatively inexpensive method to determine catalytic

Determination of oxygen to metal ratio for varying UO2 content in sintered (U,Th)O2 pellet by oxidation-reduction method using thermo-gravimetric analyser

International Nuclear Information System (INIS)

Mahanty, B.N.; Khan, F.A.; Karande, A.P.; Prakash, A.; Afzal, Md.; Panakkal, J.P.

2009-01-01

Experiments were carried out to determine oxygen to metal ratio in 4%, 6%, 10%, 20%, 50% and 80% UO 2 in sintered (U, Th) O 2 pellets by oxidation-reduction method using thermo gravimetric analyser. (author)

Investment casting using multi-jet modelling patterns: the thermogravimetric analysis of visijet® SR200 UV curable acrylate plastic

International Nuclear Information System (INIS)

Hafsa, M N; Ibrahim, M; Sharif, S

2013-01-01

Rapid Prototyping (RP) technology is actively studied to be implemented in Investment Casting (IC) process. Nowadays RP techniques are studied for their feasibility as IC master patterns, in terms of pattern collapsibility and drainage during burnout. The purpose of the study is to determine the characteristic of Visijet® SR200 acrylate material during burnout process. Traditional IC patterns made from wax have properties that limit their application in precision casting, especially for parts with thin geometries that readily break or deform when handled or dipped in the refractory slurry. Furthermore, it is not economical when producing a small number of parts. Non wax patterns fabricated for IC process, revealed ceramic shell cracking due to excessive thermal expansions, incomplete collapsibility of pattern during burnout, residual ash and poor surface finish. Thermogravimetric analysis (TGA) was used to measured the weight loss of acrylate material as the temperature was increased. TGA measured the change of material's mass as it is heated. It represents the decomposition temperature after being subjected to varying temperatures, as well as the amount of residual ash. In this experiment, the temperature range was from 20°C to 700°C with 5°C increment. Experiment results show the values of material's optimum reaction temperature and decomposing temperature of Visijet® SR200 acrylate. The percentages of remaining materials were also monitored throughout the process to obtain the amount of residual ash. All of the temperature values obtained is a resemblance for the actual burnout process and can be used as references

Synthesis, spectroscopic, structural and optical studies of Ru2S3 nanoparticles prepared from single-source molecular precursors

Science.gov (United States)

Mbese, Johannes Z.; Ajibade, Peter A.

2017-09-01

Homonuclear tris-dithiocarbamato ruthenium(III) complexes, [Ru(S2CNR2)3] were prepared and characterized by spectroscopic techniques and thermogravimetric analyses. The thermogravimetric analyses (TGA) of the ruthenium complexes showed that the complexes decompose to ruthenium(III) sulfide nanoparticles. The ruthenium(III) complexes were dispersed in oleic acid and thermolysed in hexadecylamine to prepared oleic acid/hexadecylamine capped Ru2S3 nanoparticles. FTIR revealed that Ru2S3 nanoparticles are capped through the interaction of the -NH2 group of hexadecylamine HDA adsorbed on the surfaces of nanoparticles and it also showed that oleic acid (OA) is acting as both coordinating stabilizing surfactant and capping agent. EDS spectra revealed that the prepared nanoparticles are mainly composed of Ru and S, confirming the formation of Ru2S3 nanoparticles. Powder XRD confirms that the nanoparticles are in cubic phase. The inner morphology of nanoparticles obtained from transmission electron microscopy (TEM) showed nanoparticles with narrow particle size distributions characterized by an average diameter of 8.45 nm with a standard deviation of 1.6 nm. The optical band gap (Eg) determined from Tauc plot are in the range 3.44-4.18 eV.

Study of Surface Wettability Change of Unconsolidated Sand Using Diffuse Reflectance Infrared Fourier Transform Spectroscopy and Thermogravimetric Analysis.

Science.gov (United States)

Gómora-Herrera, Diana; Navarrete Bolaños, Juan; Lijanova, Irina V; Olivares-Xometl, Octavio; Likhanova, Natalya V

2018-04-01

The effects exerted by the adsorption of vapors of a non-polar compound (deuterated benzene) and a polar compound (water) on the surface of Ottawa sand and a sample of reservoir sand (Channel), which was previously impregnated with silicon oil or two kinds of surfactants, (2-hydroxyethyl) trimethylammonium oleate (HETAO) and (2-hydroxyethyl)trimethylammonium azelate (HETAA), were studied by diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) and thermogravimetric analysis (TGA). The surface chemistry of the sandstone rocks was elucidated by X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDX). Terminal surface groups such as hydroxyls can strongly adsorb molecules that interact with these surface groups (surfactants), resulting in a wettability change. The wettability change effect suffered by the surface after treating it with surfactants was possible to be detected by the DRIFTS technique, wherein it was observed that the surface became more hydrophobic after being treated with silicon oil and HETAO; the surface became more hydrophilic after treating it with HETAA.

Thermogravimetric Analysis of Rice Husk and Coconut Pulp for Potential Bio fuel Production by Flash Pyrolysis

International Nuclear Information System (INIS)

Noorhaza Alias; Norazana Ibrahim; Mohd Kamaruddin Abdul Hamid

2014-01-01

The purpose of this paper is to study the characteristics and thermal degradation behavior of rice husk and coconut pulp for bio fuel production via flash pyrolysis technology. The elemental properties of the feedstock were characterized by an elemental analyzer while thermal properties were investigated using thermogravimetric analyzer (TGA). The pyrolysis processes were carried out at room temperature up to 700 degree Celsius in the presence of nitrogen gas flowing at 150 ml/ min. The investigated parameters are particle sizes and heating rates. The particle sizes varied in the range of dp 1 < 0.30 mm and 0.30= dp 2 <0.50 mm. The heating rates applied were 50 degree Celsius/ min and 80 degree Celsius/ min. It was shown smaller particle size produces 2.11-3.59 % less volatile product when pyrolyzed at 50 degree Celsius/ min compared to 80 degree Celsius/ min. Higher heating rates causes biomass degrades in a narrow temperature range by 25 degree Celsius. It also increases the maximum peak rate by 0.01 mg/ s for rice husk at dp 1 and 0.02 mg/ s at dp 2 . In case of coconut pulp, the change is not significant for dp 1 but for dp 2 a 0.02 mg/ s changes was recorded. (author)

Sorbents and Mechanisms of Removal

Science.gov (United States)

2010-08-21

potentiometric   titration ,   X-­‐ray  diffraction   and  FTIR   spectroscopy.  Results  of  breakthrough  tests  show  significant...thermogravimetric analyses, potentiometric titration and sorption of nitrogen. It was found that not only oxygen-containing groups but also sulfur-containing groups...using adsorption of nitrogen, XRD, FTIR, TA, and potentiometric titration . The results showed differences in the texture and chemistry of adsorbents

Correlation of resistance and thermogravimetric measurements of the Er/sub 1/Ba/sub 2/Cu/sub 3/O/sub 9-δ/ superconductor to sample preparation techniques

International Nuclear Information System (INIS)

Lee, S.I.; Golben, J.P.; Song, Y.; Chen, X.D.; McMichael, R.D.; Gaines, J.R.

1987-01-01

The resistance dependence and thermogravimetric analysis (TGA) of Er/sub 1/Ba/sub 2/Cu/sub 3/O/sub 9-δ/ has been measured in the temperature range 27 C to 920 CV. The heat treatments and oxygen flow rates simulated actual sintering and annealing processes used in sample preparation. Evidence of a phase transition in Er/sub 1/Ba/sub 2/Cu/sub 3/O/sub 9-δ/ near 680 C is discussed, as well as the implications of the maximum oxygen uptake near 400 C. The impact of sample preparation procedures on sample features is also discussed

Quantitative detection of powdered activated carbon in wastewater treatment plant effluent by thermogravimetric analysis (TGA).

Science.gov (United States)

Krahnstöver, Therese; Plattner, Julia; Wintgens, Thomas

2016-09-15

For the elimination of potentially harmful micropollutants, powdered activated carbon (PAC) adsorption is applied in many wastewater treatment plants (WWTP). This holds the risk of PAC leakage into the WWTP effluent and desorption of contaminants into natural water bodies. In order to assess a potential PAC leakage, PAC concentrations below several mg/L have to be detected in the WWTP effluent. None of the methods that are used for water analysis today are able to differentiate between activated carbon and solid background matrix. Thus, a selective, quantitative and easily applicable method is still needed for the detection of PAC residues in wastewater. In the present study, a method was developed to quantitatively measure the PAC content in wastewater by using filtration and thermogravimetric analysis (TGA), which is a well-established technique for the distinction between different solid materials. For the sample filtration, quartz filters with a temperature stability up to 950 °C were used. This allowed for sensitive and well reproducible measurements, as the TGA was not affected by the presence of the filter. The sample's mass fractions were calculated by integrating the mass decrease rate obtained by TGA in specific, clearly identifiable peak areas. A two-step TGA heating method consisting of N2 and O2 atmospheres led to a good differentiation between PAC and biological background matrix, thanks to the reduction of peak overlapping. A linear correlation was found between a sample's PAC content and the corresponding peak areas under N2 and O2, the sample volume and the solid mass separated by filtration. Based on these findings, various wastewater samples from different WWTPs were then analyzed by TGA with regard to their PAC content. It was found that, compared to alternative techniques such as measurement of turbidity or total suspended solids, the newly developed TGA method allows for a quantitative and selective detection of PAC concentrations down to 0

Sedimentation technique of waste bituminization and thermogravimetric characteristics of the final products

International Nuclear Information System (INIS)

Zeger, J.; Knotik, K.; Jakusch, H.

1976-01-01

In the research centre of the Oesterreichische Studiengesellschaft fuer Atomenergie GmbH a semi-technical plant has been installed for waste bituminization, which has been tested inactively since 1973. This plant uses a new technological process for embedding. One of the important features of this new process is that the solution water, which is normally inactive, is distilled off before embedding, resulting in dry and powdery salts. The second important feature is that these dry salts are mixed with the thin fluid bitumen by sedimentation. A special feature is that there is no mechanical aid used for mixing. Thermogravimetric analysis of samples which simulated the final products of this pilot plant was carried out to verify the best working parameters and to study the possible chemical damage to the bitumen. It was shown that only nitrate and nitrite, especially in combination with Fe(III)-ions, are of negative influence on the thermostability of bitumen. They lead to a sudden and quick weight loss of the samples between 370 and 410 0 C (above the melting point of both NaNO 2 and NaNO 3 ). The Fe-ions have a catalytic influence, as it could be shown that a 1% addition of Fe(NO 3 ) 3 to NaNO 3 leads to a considerable acceleration of the incineration. This influence of the Fe(III)-ion can be suppressed to some extent by a hydrolysis before the embedding. There is, however, no danger to the embedding process from these effects since the process temperature of maximum 200 0 C is well below the ignition temperatures. A method of measuring the dose rate of an unknown radioactive salt mixture at any point of this mixture has been developed. This is done by making two measurements with glass dose-meters, one with a beta-absorber to get a pure gamma dose and the other without it to get the combined beta and gamma dose. During the first measurement the dose-meters were protected against contamination by a thin layer of rubber

Risk Aversion in Game Shows

DEFF Research Database (Denmark)

Andersen, Steffen; Harrison, Glenn W.; Lau, Morten I.

2008-01-01

We review the use of behavior from television game shows to infer risk attitudes. These shows provide evidence when contestants are making decisions over very large stakes, and in a replicated, structured way. Inferences are generally confounded by the subjective assessment of skill in some games......, and the dynamic nature of the task in most games. We consider the game shows Card Sharks, Jeopardy!, Lingo, and finally Deal Or No Deal. We provide a detailed case study of the analyses of Deal Or No Deal, since it is suitable for inference about risk attitudes and has attracted considerable attention....

Investigation on the co-combustion of oil shale and municipal solid waste by using thermogravimetric analysis

International Nuclear Information System (INIS)

Fan, Yunlong; Yu, Zhaosheng; Fang, Shiwen; Lin, Yan; Lin, Yousheng; Liao, Yanfen; Ma, Xiaoqian

2016-01-01

Highlights: • Co-combustion of oil shale with municipal solid waste created significant changes. • Blending with municipal solid wastes could improve the combustion performance. • 10–30% of oil shale in the blends could be determined as the optimum ratio range. • Activation energy were calculated by the conversion rate and different proportion. - Abstract: The aim of this study is trying to reveal the thermal characteristics and kinetics of oil shale, municipal solid waste and their blends in the combustion process which are needed for efficient utilization. The combustion experiment is carried out in a thermogravimetric simultaneous thermal analyzer, where the temperature ranged from 110 °C to 900 °C at three different heating rates as 10 °C/min, 20 °C/min and 30 °C/min. Their kinetics were studied by Ozawa–Flynn–Wall and Friedmen methods. According to the data analysis, combustion characteristic index increased progressively with the increase of the proportion of municipal solid waste. And it’s suggested that there was certain interaction in the combustion process of oil shale and municipal solid waste. The average activation energy of the blends reached the minimum value, 177.7927 kJ/mol by Ozawa–Flynn–Wall method and 167.4234 kJ/mol by Friedmen method, when the proportion of MSW was 70%.

Understanding of thermo-gravimetric analysis to calculate number of addends in multifunctional hemi-ortho ester derivatives of fullerenol

International Nuclear Information System (INIS)

Singh, Rachana; Goswami, Thakohari

2011-01-01

Test results for the applicability of existing thermo-gravimetric analysis (TGA) technique to ascertain average number of exohedral chemical attachment in a new class of fullerene dyads consisting of multiple hemi-ortho esters onto fullerenol is presented. Although the method is nicely applicable for higher fullerenol, but homogeneous phase products calculate lower number of addends, whereas, the hetero phase products indicate higher value. Lower value is attributed to either overlapping of thermal events or substituents effects and higher value is the contribution of tetra butyl ammonium hydroxide (TBAH) impurity used as phase transfer catalyst (PTC) in heterogeneous phase reactions. Presence of TBAH impurity is recognized through thermo-gravimetry mass spectrometry (TG-MS) measurement. Appropriate modification of test method to arrive at accurate and precise values of x (total mass contribution due to addends only) and y (total mass contribution due to fullerene plus char yield) are also reported. Successful use of two more different techniques, viz., electron-spray ionization mass spectrometry (ESI-MS) and X-ray photoelectron spectroscopy (XPS), supplement above results. Influences of fullerene and different substituents on thermal behavior of dyads are assessed.

Measurement of the oxidation of spent fuel between 140/degree/ and 225/degree/C by thermogravimetric analysis

International Nuclear Information System (INIS)

Woodley, R.E.; Einziger, R.E.; Buchanan, H.C.

1988-09-01

A series of PWR spent fuel samples from Turkey Point Unit 3 have been oxidized at temperatures between 140/degree/ and 225/degree/C in air atmospheres with dew points between 14.5/degree/ and /minus/70/degree/C, using a thermogravimetric analysis system (TGA). Tests lasted between 400 and 2100 hours. At the conclusion of a test, the atmosphere was sampled to determine the release of fission gas during testing, and the fuel samples were analyzed for microstructural changes. It appears that the mechanism for oxidation of spent fuel to U/sub 3/O/sub 7/ takes place in two steps that occur somewhat simultaneously. Oxygen migrates along the grain boundaries, which are oxidized and enlarged. The grains oxidize by the inward progression of a layer of U/sub 4/O/sub 9/ saturated with oxygen. A simplified model of the mechanism, which considers oxygen diffusion through the product layer as the rate-controlling step, yields an activation energy of 27 /plus minus/ 4 kcal/mol. Moisture, between dew points of /minus/70/degree/ to +14.5/degree/C, i.e., water vapor partial pressures varying over four orders of magnitude, had no significant effect on the oxidation rate. 34 refs., 12 figs., 6 tabs

Synergetic effect of sewage sludge and biomass co-pyrolysis: A combined study in thermogravimetric analyzer and a fixed bed reactor

International Nuclear Information System (INIS)

Wang, Xuebin; Deng, Shuanghui; Tan, Houzhang; Adeosun, Adewale; Vujanović, Milan; Yang, Fuxin; Duić, Neven

2016-01-01

Highlights: • The synergetic effect of sewage sludge and wheat straw co-pyrolysis was studied. • The mass balance measurement of gas, tar, and char was performed. • The synergetic effect shows strongest under a certain biomass addition ratio around 60%. • The required heat of co-pyrolysis is significantly reduced. - Abstract: Much attention has been given to the valuable products from the pyrolysis of sewage sludge. In this study, the pyrolysis of sewage sludge, biomass (wheat straw) and their mixtures in different proportions were carried out in a thermogravimetric analyzer (TGA) and fixed-bed reactor. The effects of pyrolysis temperature and percentage of wheat straw in wheat straw–sewage sludge mixtures on product distributions in terms of gas, liquid and char and the gas composition were investigated. Results indicate that there is a significantly synergetic effect during the co-pyrolysis processes of sewage sludge and wheat straw, accelerating the pyrolysis reactions. The synergetic effect resulted in an increase in gas and liquid yields but a decrease in char yield. The gas composition and the synergetic effect degree are strongly affected by the wheat straw proportions, and the strongest synergetic effect of sewage sludge and wheat straw co-pyrolysis appears at the biomass proportion of 60 wt.%. With an increase of temperature, the gas yield from the pyrolysis of sewage sludge increased but the liquid and char yields decreased. Moreover, the required heat of co-pyrolysis is significantly reduced compared with the pyrolysis of sewage sludge and wheat straw pyrolysis alone, because of the exothermic reactions between the ash components in two fuel samples.

Radiation damage and annealing in plutonium tetrafluoride

Science.gov (United States)

McCoy, Kaylyn; Casella, Amanda; Sinkov, Sergey; Sweet, Lucas; McNamara, Bruce; Delegard, Calvin; Jevremovic, Tatjana

2017-12-01

A sample of plutonium tetrafluoride that was separated prior to 1966 at the Hanford Site in Washington State was analyzed at the Pacific Northwest National Laboratory (PNNL) in 2015 and 2016. The plutonium tetrafluoride, as received, was an unusual color and considering the age of the plutonium, there were questions about the condition of the material. These questions had to be answered in order to determine the suitability of the material for future use or long-term storage. Therefore, thermogravimetric/differential thermal analysis and X-ray diffraction evaluations were conducted to determine the plutonium's crystal structure, oxide content, and moisture content; these analyses reported that the plutonium was predominately amorphous and tetrafluoride, with an oxide content near ten percent. Freshly fluorinated plutonium tetrafluoride is known to be monoclinic. During the initial thermogravimetric/differential thermal analyses, it was discovered that an exothermic event occurred within the material near 414 °C. X-ray diffraction analyses were conducted on the annealed tetrafluoride. The X-ray diffraction analyses indicated that some degree of recrystallization occurred in conjunction with the 414 °C event. The following commentary describes the series of thermogravimetric/differential thermal and X-ray diffraction analyses that were conducted as part of this investigation at PNNL.

Radiation damage and annealing in plutonium tetrafluoride

Energy Technology Data Exchange (ETDEWEB)

McCoy, Kaylyn; Casella, Amanda; Sinkov, Sergey; Sweet, Lucas; McNamara, Bruce; Delegard, Calvin; Jevremovic, Tatjana

2017-12-01

Plutonium tetrafluoride that was separated prior to 1966 at the Hanford Site in Washington State was analyzed at the Pacific Northwest National Laboratory (PNNL) in 2015 and 2016. The plutonium tetrafluoride, as received, was an off-normal color and considering the age of the plutonium, there were questions about the condition of the material. These questions had to be answered in order to determine the suitability of the material for future use or long-term storage. Therefore, Thermogravimetric/Differential Thermal Analysis and X-ray Diffraction evaluations were conducted to determine the plutonium’s crystal structure, oxide content, and moisture content; these analyses reported that the plutonium was predominately amorphous and tetrafluoride, with an oxide content near ten percent. Freshly fluorinated plutonium tetrafluoride is known to be monoclinic. During the initial Thermogravimetric/Differential Thermal analyses, it was discovered that an exothermic event occurred within the material near 414°C. X-ray Diffraction analyses were conducted on the annealed tetrafluoride. The X-ray Diffraction analyses indicated that some degree of recrystallization occurred in conjunction with the 414°C event. The following commentary describes the series of Thermogravimetric/Differential Thermal and X-ray Diffraction analyses that were conducted as part of this investigation at PNNL, in collaboration with the University of Utah Nuclear Engineering Program.

Radiation damage and annealing in plutonium tetrafluoride

International Nuclear Information System (INIS)

McCoy, Kaylyn; Casella, Amanda; Sinkov, Sergey

2017-01-01

A sample of plutonium tetrafluoride that was separated prior to 1966 at the Hanford Site in Washington State was analyzed at the Pacific Northwest National Laboratory (PNNL) in 2015 and 2016. The plutonium tetrafluoride, as received, was an unusual color and considering the age of the plutonium, there were questions about the condition of the material. These questions had to be answered in order to determine the suitability of the material for future use or long-term storage. Therefore, thermogravimetric/differential thermal analysis and X-ray diffraction evaluations were conducted to determine the plutonium's crystal structure, oxide content, and moisture content; these analyses reported that the plutonium was predominately amorphous and tetrafluoride, with an oxide content near ten percent. Freshly fluorinated plutonium tetrafluoride is known to be monoclinic. And during the initial thermogravimetric/differential thermal analyses, it was discovered that an exothermic event occurred within the material near 414 °C. X-ray diffraction analyses were conducted on the annealed tetrafluoride. The X-ray diffraction analyses indicated that some degree of recrystallization occurred in conjunction with the 414 °C event. This commentary describes the series of thermogravimetric/differential thermal and X-ray diffraction analyses that were conducted as part of this investigation at PNNL.

Characterization of Synthesized and Commercial Forms of Magnesium Stearate Using Differential Scanning Calorimetry, Thermogravimetric Analysis, Powder X-Ray Diffraction, and Solid-State NMR Spectroscopy.

Science.gov (United States)

Delaney, Sean P; Nethercott, Matthew J; Mays, Christopher J; Winquist, Nickolas T; Arthur, Donia; Calahan, Julie L; Sethi, Manish; Pardue, Daniel S; Kim, Junghyun; Amidon, Gregory; Munson, Eric J

2017-01-01

Magnesium stearate is the salt of a complex mixture of fatty acids, with the majority being stearate and palmitate. It has multiple crystalline forms and, potentially, an amorphous form. Magnesium stearate is used in the pharmaceutical manufacturing industry as a powder lubricant, and typically is added at low levels (∼1%) during the manufacturing process and blended for a relatively short time (∼5 min). Proper levels and mixing times are needed, as too short a mixing time or too small a quantity will result in improper lubrication, and too much can negatively impact dissolution rates. The complex mixture of multiple fatty acids and crystalline forms in magnesium stearate leads to variability between commercial sources, and switching between sources can impact both the amount of lubricant and mixing time needed for proper lubrication. In order to better understand the complex nature of magnesium stearate, a variety of analytical techniques were used to characterize both synthesized and commercial magnesium stearate samples. The results show that correlation among differential scanning calorimetry, thermogravimetric analysis, solid-state NMR spectroscopy, and other techniques provides a unique insight into the forms of magnesium stearate. Finally, the ability to monitor form changes of magnesium stearate in an intact tablet using solid-state NMR spectroscopy is shown. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Kinetic Parameters of Non-Isothermal Thermogravimetric Non-Catalytic and Catalytic Pyrolysis of Empty Fruit Bunch with Alumina by Kissinger and Ozawa Methods

Science.gov (United States)

Rahayu Mohamed, Alina; Li, Nurfahani; Sohaimi, Khairunissa Syairah Ahmad; Izzati Iberahim, Nur; Munirah Rohaizad, Nor; Hamzah, Rosniza

2018-03-01

The non-isothermal thermogravimetric non-catalytic and catalytic empty fruit bunch (EFB) pyrolysis with alumina were performed at different heating rates of 10, 15, 20, 25, 30 and 40 K/min under nitrogen atmosphere at a flow rate of 100 ml/min under dynamic conditions from 301 K to 1273 K. The activation energy were calculated based on Kissinger and Ozawa methods. Both reactions followed first order reactions. By Kissinger method, the activation energy and Ln A values for non-catalytic and catalytic EFB pyrolysis with alumina were 188.69 kJ mol-1 and 201.67 kJ/mol respectively. By Ozawa method, the activation energy values for non-catalytic and catalytic EFB pyrolysis with alumina were 189.13 kJ/mol and 201.44 kJ/mol respectively. The presence of catalyst increased the activation energy values for EFB pyrolysis as calculated by Kissinger and Ozawa methods.

Kinetic model of the thermal pyrolysis of chrome tanned leather treated with NaOH under different conditions using thermogravimetric analysis.

Science.gov (United States)

Bañón, E; Marcilla, A; García, A N; Martínez, P; León, M

2016-02-01

The thermal decomposition of chrome tanned leather before and after a soaking treatment with NaOH was studied using thermogravimetric analysis (TGA). The effect of the solution concentration (0.2M and 0.5M) and the soaking time (5min and 15min) was evaluated. TGA experiments at four heating rates (5, 10, 15 and 20°Cmin(-1)) were run in a nitrogen atmosphere for every treatment condition. A kinetic model was developed considering the effect of the three variables studied, i.e.: the NaOH solution concentration, the soaking time and the heating rate. The proposed model for chrome tanned leather pyrolysis involves a set of four reactions, i.e.: three independent nth order reactions, yielding the corresponding products and one of them undergoing a successive cero order reaction. The model was successfully applied simultaneously to all the experimental data obtained. The evaluation of the kinetic parameters obtained (activation energy, pre-exponential factor and reaction order) allowed a better understanding of the effect of the alkali treatment on these wastes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Sedimentation technique of waste bituminization and thermogravimetric characteristics of the final products

Energy Technology Data Exchange (ETDEWEB)

Zeger, J; Knotik, K; Jakusch, H

1976-01-01

In the research centre of the Oesterreichische Studiengesellschaft fuer Atomenergie GesmbH a semitechnical plant has been installed for waste bituminization, which has been tested inactively since 1973. This plant is using a new technological process for embedding. One of the important features of this new process is that the, normally inactive solution water is distilled off prior to the embedding, resulting in dry and powdery salts. The second important feature is that the mixing of these dry salts with the thin fluid bitumen is done by sedimentation. Expecially there is no mechanical aid used for mixing. Thermogravimetric analysis of samples which simulated the final products of this pilot plant, were carried out to verify the best working parameters and to study the possible chemical damage to the bitumen. Analysis was performed by heating the samples, consisting of various mixtures of bitumen and inorganic salts, in a METTLER-Thermoanalyzer up to 500/sup 0/C using different atmospheres (air, nitrogen). It could be shown that only nitrate and nitrite especially in combination with Fe(III)-ions are of negative influence on the thermostability of bitumen. They lead to a sudden and quick weight loss of the samples between 370 and 410/sup 0/C (above the melting point of both NaNO/sub 2/ and NaNO/sub 3/). The Fe-ions hava a catalytic influence, as it could be shown that 1 1% addiation of Fe(NO/sub 3/)/sub 3/ to NaNO/sub 3/ leads to a considerable acceleration of the incineration. This influence of the Fe(III)-ion can be suppressed to some extend by a hydrolysis prior to the embedding. In preparation of further studies concerning the behaviour of radiation damaged bitumen there has been developed a method of measuring the dose rate of an unknown radioactive salt mixture at any point of this mixture. This is done by making two measurements with glass dosimeters. One with a beta-absorber to get a pure gamma-dose and the other without it to get the combined beta and

Palladium nanoparticles supported on layered hydroxide salts and their use in carbon-carbon coupling organic reactions

OpenAIRE

Martínez,Maby; Ocampo,Rogelio; Rios,Luz Amalia; Ramírez,Alfonso; Giraldo,Oscar

2011-01-01

Palladium nanoparticles supported on zinc hydroxide salts were prepared by intercalation of [PdCl6]2- and its further reduction with ethanol under reflux. All the materials were completely characterized by atomic absorption spectroscopy (AAS), X-ray diffraction (XRD), thermogravimetric/derivative thermogravimetric (TG/DTG) analyses, scanning electron microscopy (SEM), UV-Visible spectrometry and transmission electron microscopy (TEM). TEM analysis confirmed that the palladium nanoparticles we...

The research of moisture forms in the baking yeast by the thermogravimetric analysis method

Directory of Open Access Journals (Sweden)

S. V. Lavrov

2016-01-01

Full Text Available The thermogravimetry method is one of the few absolute methods of analysis, that makes it one of the most accurate methods. In this research, thermogravimetric analysis of baking yeast (Saccharomyces cerevisiae was carried out. It allowed to identify temperature zones, which correspond to dripping with various link energy, as well as to predict operating parameters of the process of dehumidification and to choose their most effective dehydration method. The studies were conducted in the laboratory of the collective use center "Control and management of energy efficient projects" of the "Voronezh state university of engineering technologies" on the simultaneous thermal analysis device STA 449 F3 model (NETZSCH, Germany. The device records the change in a substance mass and the difference of the heat flow inside the crucible containing the sample and the crucible containing the standard analyte. The analyzer's working principle is based on continuous recording of the dependence of the material mass on time or temperature and its being heated to the selected temperature program in a specified gas atmosphere. The release or absorption of heat by the sample due to phase transitions or chemical reactions is recorded simultaneously. The study was performed in the following modes: the pressure is atmospheric, the maximum temperature is 588 K, the rate of temperature change is 5 K/min. The experiments were performed in aluminum crucibles with a total weight of 12 mg. The software NETZSCH Proteus was used for processing of the obtained TG and DTG curves. The analysis of the obtained data allowed to identify periods of water dehydration and solids transformation by thermal effect on baking yeast, and to identify temperature zones, which correspond to the release of moisture with different link form and energy.

Preliminary Analyses Showed Short-Term Mental Health Improvements after a Single-Day Manager Training.

Science.gov (United States)

Boysen, Elena; Schiller, Birgitta; Mörtl, Kathrin; Gündel, Harald; Hölzer, Michael

2018-01-10

Psychosocial working conditions attract more and more attention when it comes to mental health in the workplace. Trying to support managers to deal with their own as well as their employees' psychological risk factors, we conducted a specific manager training. Within this investigation, we wanted to learn about the training's effects and acceptance. A single-day manager training was provided in a large industrial company in Germany. The participants were asked to fill out questionnaires regarding their own physical and mental health condition as well as their working situation. Questionnaires were distributed at baseline, 3-month, and 12-month follow-up. At this point of time the investigation is still ongoing. The current article focuses on short-term preliminary effects. Analyses only included participants that already completed baseline and three months follow-up. Preliminary results from three-month follow-up survey ( n = 33, nmale = 30, Mage = 47.5) indicated positive changes in the manager's mental health condition measured by the Patient Health Questionnaire for depression (PHQ-9: Mt1 = 3.82, Mt2 = 3.15). Training managers about common mental disorders and risk factors at the workplace within a single-day workshop seems to promote positive effects on their own mental health. Especially working with the managers on their own early stress symptoms might have been an important element.

Study of thermal stability and degradation of fire resistant candidate polymers for aircraft interiors

Science.gov (United States)

Hsu, M. T. S.

1976-01-01

The thermochemistry of bismaleimide resins and phenolphthalein polycarbonate was studied. Both materials are fire-resistant polymers and may be suitable for aircraft interiors. The chemical composition of the polymers has been determined by nuclear magnetic resonance and infrared spectroscopy and by elemental analysis. Thermal properties of these polymers have been characterized by thermogravimetric analyses. Qualitative evaluation of the volatile products formed in pyrolysis under oxidative and non-oxidative conditions has been made using infrared spectrometry. The residues after pyrolysis were analyzed by elemental analysis. The thermal stability of composite panel and thermoplastic materials for aircraft interiors was studied by thermogravimetric analyses.

Study of solid chemical evolution in torrefaction of different biomasses through solid-state "1"3C cross-polarization/magic angle spinning NMR (nuclear magnetic resonance) and TGA (thermogravimetric analysis)

International Nuclear Information System (INIS)

Rodriguez Alonso, Elvira; Dupont, Capucine; Heux, Laurent; Da Silva Perez, Denilson; Commandre, Jean-Michel; Gourdon, Christophe

2016-01-01

The objective of this work is to compare mass loss and chemical evolution of the solid phase, versus time, during dynamic torrefaction of different types of biomass. For this purpose, two experiments, ThermoGravimetric Analysis and solid-state "1"3C Cross-Polarization/Magic Angle Spinning Nuclear Magnetic Resonance, were run on four representative biomasses. Overall mass loss and chemical evolution of the solid phase were followed, respectively, as a function of temperature and time. Thanks to this coupled information, it was shown that the knowledge of both solid mass loss and chemical evolution is necessary to characterize torrefaction severity. Moreover, biomasses containing higher proportions of xylan lost mass faster than those containing lower proportions. Lignin showed a protecting role towards cellulose, which would lead to a faster degradation of non-woody biomasses in comparison with woody biomasses. Three parameters would have an influence on solid chemical evolution during torrefaction: xylan content in hemicellulose, lignin content in biomass, and cellulose crystallinity. - Highlights: • Torrefaction of four biomasses was studied with TGA and solid-state NMR. • Both solid mass loss and chemical evolution characterize torrefaction severity. • Biomasses containing a higher proportion of xylan lose mass faster. • Lignin shows a stronger protecting role in degradation of woody biomasses. • Xylan, lignin and crystalline cellulose values influence solid chemical evolution.

Characterization of the Sublimation and Vapor Pressure of 2-(2-Nitrovinyl) Furan (G-0) Using Thermogravimetric Analysis: Effects of Complexation with Cyclodextrins.

Science.gov (United States)

Ruz, Vivian; González, Mirtha Mayra; Winant, Danny; Rodríguez, Zenaida; Van den Mooter, Guy

2015-08-19

In the present work, the sublimation of crystalline solid 2-(2-nitrovinyl) furan (G-0) in the temperature range of 35 to 60 °C (below the melting point of the drug) was studied using thermogravimetric analysis (TGA). The sublimated product was characterized using Fourier-transformed-infrared spectroscopy (FT-IR) and thin layer chromatography (TLC). The sublimation rate at each temperature was obtained using the slope of the linear regression model and followed apparent zero-order kinetics. The sublimation enthalpy from 35 to 60 °C was obtained from the Eyring equation. The Gückel method was used to estimate the sublimation rate and vapor pressure at 25 °C. Physical mixtures, kneaded and freeze-dried complexes were prepared with 2-hydroxypropyl-β-cyclodextrin (HP-β-CD) and sulfobutyl ether-β-cyclodextrin (SBE-β-CD) and analyzed using isothermal TGA at 50 °C. The complexation contributed to reducing the sublimation process. The best results were achieved using freeze-dried complexes with both cyclodextrins.

Development of sampling systems and special analyses for pressurized gasification processes; Paineistettujen kaasutusprosessien naeytteenottomenetelmien ja erityisanalytiikan kehittaeminen

Energy Technology Data Exchange (ETDEWEB)

Staahlberg, P.; Oesch, P.; Leppaemaeki, E.; Moilanen, A.; Nieminen, M.; Korhonen, J. [VTT Energy, Espoo (Finland)

1996-12-01

The reliability of sampling methods used for measuring impurities contained in gasification gas were studied, and new methods were developed for sampling and sample analyses. The aim of the method development was to improve the representativeness of the samples and to speed up the analysis of gas composition. The study focused on tar, nitrogen and sulphur compounds contained in the gasification gas. In the study of the sampling reliability, the effects of probe and sampling line materials suitable for high temperatures and of the solids deposited in the sampling devices on gas samples drawn from the process were studied. Measurements were carried out in the temperature range of 250 - 850 deg C both in real conditions and in conditions simulating gasification gas. The durability of samples during storage was also studied. The other main aim of the study was to increase the amount of quick-measurable gas components by developing on-line analytical methods based on GC, FTIR and FI (flow injection) techniques for the measurements of nitrogen and sulphur compounds in gasification gas. As these methods are suitable only for the gases that do not contain condensing gas components disturbing the operation of analysers (heavy tar compounds, water), a sampling system operating in dilution principle was developed. The system operates at high pressures and temperatures and is suitable for gasification gases containing heavy tar compounds. The capabilities of analysing heavy tar compounds (mole weight >200 g mol) was improved by adding the amount of compounds identified and calibrated by model substances and by developing analytical methods based on the high-temperature-GC analysis and the thermogravimetric method. (author)

Obtaining and characterization of composites PHBV/attapulgite

International Nuclear Information System (INIS)

Silva, Liliane C.A.; Thire, Rossana M.S.M.; Barreto, Ledjane S.

2009-01-01

In this paper, poly (3-hydroxybutyrate-co-3-hydroxyvalerate)/attapulgite (PHBV/AT) composites were prepared by solution intercalation method. The microstructure and thermal properties of the composites were studied by X-ray diffraction and thermogravimetric analyses. Experimental results suggest the insertion of the polymeric chains in the channels of the clay. There were no significant changes in the thermogravimetric profile of the films due to the presence of attapulgite. (author)

Phenotypic and functional analyses show stem cell-derived hepatocyte-like cells better mimic fetal rather than adult hepatocytes.

Science.gov (United States)

Baxter, Melissa; Withey, Sarah; Harrison, Sean; Segeritz, Charis-Patricia; Zhang, Fang; Atkinson-Dell, Rebecca; Rowe, Cliff; Gerrard, Dave T; Sison-Young, Rowena; Jenkins, Roz; Henry, Joanne; Berry, Andrew A; Mohamet, Lisa; Best, Marie; Fenwick, Stephen W; Malik, Hassan; Kitteringham, Neil R; Goldring, Chris E; Piper Hanley, Karen; Vallier, Ludovic; Hanley, Neil A

2015-03-01

Hepatocyte-like cells (HLCs), differentiated from pluripotent stem cells by the use of soluble factors, can model human liver function and toxicity. However, at present HLC maturity and whether any deficit represents a true fetal state or aberrant differentiation is unclear and compounded by comparison to potentially deteriorated adult hepatocytes. Therefore, we generated HLCs from multiple lineages, using two different protocols, for direct comparison with fresh fetal and adult hepatocytes. Protocols were developed for robust differentiation. Multiple transcript, protein and functional analyses compared HLCs to fresh human fetal and adult hepatocytes. HLCs were comparable to those of other laboratories by multiple parameters. Transcriptional changes during differentiation mimicked human embryogenesis and showed more similarity to pericentral than periportal hepatocytes. Unbiased proteomics demonstrated greater proximity to liver than 30 other human organs or tissues. However, by comparison to fresh material, HLC maturity was proven by transcript, protein and function to be fetal-like and short of the adult phenotype. The expression of 81% phase 1 enzymes in HLCs was significantly upregulated and half were statistically not different from fetal hepatocytes. HLCs secreted albumin and metabolized testosterone (CYP3A) and dextrorphan (CYP2D6) like fetal hepatocytes. In seven bespoke tests, devised by principal components analysis to distinguish fetal from adult hepatocytes, HLCs from two different source laboratories consistently demonstrated fetal characteristics. HLCs from different sources are broadly comparable with unbiased proteomic evidence for faithful differentiation down the liver lineage. This current phenotype mimics human fetal rather than adult hepatocytes. Copyright © 2014 European Association for the Study of the Liver. Published by Elsevier B.V. All rights reserved.

Thermogravimetric study of thermal decontamination of soils polluted by hexachlorobenzene, 4-chlorobiphenyl, naphthalene, or n-decane.

Science.gov (United States)

Risoul, V; Pichon, C; Trouvé, G; Peters, W A; Gilot, P; Prado, G

1999-02-15

To determine decontamination behavior as affected by temperature, shallow beds of a clay-rich, a calcerous, and a sedimentary soil, artificially polluted with hexachlorobenzene, 4-chlorobiphenyl, naphthalene, or n-decane, were separately heated at 5 degrees C min-1 in a thermogravimetric analyzer. Temperatures for deep cleaning of the calcerous and the sedimentary soil increased with increasing boiling point (bp) of the aromatic contaminants, but removal efficiencies still approached 100% well below the bp. Decontamination rates were therefore modelled according to a pollutant evaporation-diffusion transport model. For the calcerous and sedimentary soils, this model reasonably correlated removal of roughly the first 2/3 of the naphthalene, but gave only fair predictions for hexachlorobenzene and 4-chlorobiphenyl. It was necessary to heat the clay soil above the aromatics bp to achieve high decontamination efficiencies. Weight loss data imply that for temperatures from near ambient to as much as 150 degrees C, interactions of each aromatic with the clay soil, or its decomposition products, result in lower net volatilization of the contaminated vs. neat clay. A similar effect was observed in heating calcerous soil polluted with hexachlorobenzene from near ambient to about 140 degrees C. Decontamination mechanisms remain to be established, although the higher temperatures needed to remove aromatics from the clay may reflect a more prominent role for surface desorption than evaporation. This would be consistent with our estimates that the clay can accommodate all of the initial pollutant loadings within a single surface monolayer, whereas the calcerous and sedimentary soils cannot.

Morphological Changes of Limestone Sorbent Particles during Carbonation/Calcination Looping Cycles in a Thermogravimetric Analyzer (TGA) and Reactivation with Steam

KAUST Repository

Wu, Y.

2010-04-15

Carbonation and calcination looping cycles were carried out on four limestones in a thermogravimetric analyzer (TGA). The CO2 carrying capacity of a limestone particle decays very quickly in the first 10 cycles, reducing to about 20% of its original uptake capacity after 10 cycles for the four limestones studied in this work, and it decreases further to 6-12% after 50 cycles. A new steam reactivation method was applied on the spent sorbent to recover the loss of reactivity. The steam reactivation of multi-cycled samples was conducted at atmospheric pressure. Steam reactivation for 5 min at 130 °C of particles that had undergone 10 cycles resulted in an immediate increase (by 45-60% points) in carrying capacity. The morphological changes of limestone particles during the cycling and steam reactivation were studied using both an optical microscope and scanning electron microscopy (SEM). The diameters of limestone particles shrank by about 2-7% after 10 carbonation/calcination cycles, and the particle diameters swelled significantly (12-22% increase) after steam reactivation. These size changes are important for studies of attrition and mathematical modeling of carbonation. © 2010 American Chemical Society.

Bulletin of Materials Science | Indian Academy of Sciences

Indian Academy of Sciences (India)

6O18].10H2O, has been synthesized and structurally characterized by single crystal X-ray diffraction, elemental analyses, IR, UV–Vis spectra and thermogravimetric analyses. This compound crystallized in the triclinic system, space group -1, ...

Investigation on the co-combustion of low calorific oil shale and its semi-coke by using thermogravimetric analysis

International Nuclear Information System (INIS)

Yang, Yu; Lu, Xiaofeng; Wang, Quanhai

2017-01-01

Highlights: • The co-combustion characteristic parameters were studied. • The co-combustion of oil shale and semi-coke could be expressed roughly by the addition of individual components. • Activation energy was calculated by Coats-Redfern, distributed activation energy model and Flynn-Wall-Ozawa methods. - Abstract: In the present work, thermogravimetric analysis was employed to investigate co-combustion behaviors of Fushun low calorific oil shale and its semi-coke. The synergy effect was estimated by using the interaction coefficient and the relative error of mean square root. In addition, activation energy was also calculated by means of Coats-Redfern, distributed activation energy model and Flynn-Wall-Ozawa methods. Results indicated that with the increase of oil shale mass fraction and oxygen concentration, combustion characteristics of the samples were improved. And some little interaction did occur during the co-combustion process, but it was relatively slight. Consequently, the co-combustion of oil shale and semi-coke still could be expressed roughly by the addition of individual components of the mixtures. Furthermore, activation energy of the samples decreased slowly at the initial stage attributed to the minerals’ catalytic effects, and in the final stage, it jumped to a high value, suggesting that the burnout of the samples was difficult. Besides, the mix proportion of oil shale which was added to stabilize the combustion in the circulating fluidized bed was also theoretically calculated.

Thermal and Chemical Characterization of Non-Metallic Materials Using Coupled Thermogravimetric Analysis and Infrared Spectroscopy

Science.gov (United States)

Huff, Timothy L.

2002-01-01

Thermogravimetric analysis (TGA) is widely employed in the thermal characterization of non-metallic materials, yielding valuable information on decomposition characteristics of a sample over a wide temperature range. However, a potential wealth of chemical information is lost during the process, with the evolving gases generated during thermal decomposition escaping through the exhaust line. Fourier Transform-Infrared spectroscopy (FT-IR) is a powerful analytical technique for determining many chemical constituents while in any material state, in this application, the gas phase. By linking these two techniques, evolving gases generated during the TGA process are directed into an appropriately equipped infrared spectrometer for chemical speciation. Consequently, both thermal decomposition and chemical characterization of a material may be obtained in a single sample run. In practice, a heated transfer line is employed to connect the two instruments while a purge gas stream directs the evolving gases into the FT-IR. The purge gas can be either high purity air or an inert gas such as nitrogen to allow oxidative and pyrolytic processes to be examined, respectively. The FT-IR data is collected realtime, allowing continuous monitoring of chemical compositional changes over the course of thermal decomposition. Using this coupled technique, an array of diverse materials has been examined, including composites, plastics, rubber, fiberglass epoxy resins, polycarbonates, silicones, lubricants and fluorocarbon materials. The benefit of combining these two methodologies is of particular importance in the aerospace community, where newly developing materials have little available data with which to refer. By providing both thermal and chemical data simultaneously, a more definitive and comprehensive characterization of the material is possible. Additionally, this procedure has been found to be a viable screening technique for certain materials, with the generated data useful in

Making sense of enthalpy of vaporization trends for ionic liquids: new experimental and simulation data show a simple linear relationship and help reconcile previous data.

Science.gov (United States)

Verevkin, Sergey P; Zaitsau, Dzmitry H; Emel'yanenko, Vladimir N; Yermalayeu, Andrei V; Schick, Christoph; Liu, Hongjun; Maginn, Edward J; Bulut, Safak; Krossing, Ingo; Kalb, Roland

2013-05-30

Vaporization enthalpy of an ionic liquid (IL) is a key physical property for applications of ILs as thermofluids and also is useful in developing liquid state theories and validating intermolecular potential functions used in molecular modeling of these liquids. Compilation of the data for a homologous series of 1-alkyl-3-methylimidazolium bis(trifluoromethane-sulfonyl)imide ([C(n)mim][NTf2]) ILs has revealed an embarrassing disarray of literature results. New experimental data, based on the concurring results from quartz crystal microbalance, thermogravimetric analyses, and molecular dynamics simulation have revealed a clear linear dependence of IL vaporization enthalpies on the chain length of the alkyl group on the cation. Ambiguity of the procedure for extrapolation of vaporization enthalpies to the reference temperature 298 K was found to be a major source of the discrepancies among previous data sets. Two simple methods for temperature adjustment of vaporization enthalpies have been suggested. Resulting vaporization enthalpies obey group additivity, although the values of the additivity parameters for ILs are different from those for molecular compounds.

Three new hydrochlorothiazide cocrystals: Structural analyses and solubility studies

Science.gov (United States)

Ranjan, Subham; Devarapalli, Ramesh; Kundu, Sudeshna; Vangala, Venu R.; Ghosh, Animesh; Reddy, C. Malla

2017-04-01

Hydrochlorothiazide (HCT) is a diuretic BCS class IV drug with poor aqueous solubility and low permeability leading to poor oral absorption. The present work explores the cocrystallization technique to enhance the aqueous solubility of HCT. Three new cocrystals of HCT with water soluble coformers phenazine (PHEN), 4-dimethylaminopyridine (DMAP) and picolinamide (PICA) were prepared successfully by solution crystallization method and characterized by single crystal X-ray diffraction (SCXRD), powder X-ray diffraction (PXRD), fourier transform -infraredspectroscopy (FT-IR), differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Structural characterization revealed that the cocrystals with PHEN, DMAP and PICA exists in P21/n, P21/c and P21/n space groups, respectively. The improved solubility of HCT-DMAP (4 fold) and HCT-PHEN (1.4 fold) cocrystals whereas decreased solubility of HCT-PICA (0.5 fold) as compared to the free drug were determined after 4 h in phosphate buffer, pH 7.4, at 25 °C by using shaking flask method. HCT-DMAP showed a significant increase in solubility than all previously reported cocrystals of HCT suggest the role of a coformer. The study demonstrates that the selection of coformer could have pronounced impact on the physicochemical properties of HCT and cocrystallization can be a promising approach to improve aqueous solubility of drugs.

Caracterização físico-química do óleo essencial da Siparuna guianensis Aublet

Directory of Open Access Journals (Sweden)

Augustus Caeser Franke Portella

2014-06-01

Full Text Available Thermal and spectroscopic analyses of essential oil extracted from Siparuna guianensis Aublet, an aromatic plant belonging to medicinal ethnobotany family Siparunaceae, were carried out. The plant is known throughout the North and Northeast of Brazil by the name negramina and has wide application as a natural insect repellent. Thermogravimetric analyses were correlated with the Arrhenius Equation to provide kinetic parameters of evaporation, including activation energy and frequency factor. Differential scanning calorimetric analysis showed the presence of an exothermic oxidation peak, probably as a result of transformations and decomposition of the solid structure before melting.

Synthesis, Spectral, Thermogravimetric, XRD, Molecular Modelling and Potential Antibacterial Studies of Dimeric Complexes with Bis Bidentate ON–NO Donor Azo Dye Ligands

Directory of Open Access Journals (Sweden)

Bipin Bihari Mahapatra

2013-01-01

Full Text Available The dimeric complexes of Co(II, Ni(II, Cu(II, Zn(II, Cd(II, and Hg(II with two new symmetrical ON–NO donor bis bidentate (tetradentate azo dye ligands, LH2 = 4,4′-bis(4′-hydroxyquinolinolinylazodiphenylsulphone, and L′H2 = 4,4′-bis(acetoacetanilideazodiphenylsulphone have been synthesized. The metal complexes have been characterised by elemental analytical, conductance, magnetic susceptibility, IR, electronic spectra, ESR, NMR, thermogravimetry, X-ray diffraction (powder pattern spectra, and molecular modelling studies. The Co(II and Ni(II complexes are found to be octahedral, Cu(II complexes are distorted octahedral, and a tetrahedral stereochemistry has been assigned to Zn(II, Cd(II, and Hg(II complexes. The thermogravimetric study indicates that compounds are quite stable. The energy optimized structures are proposed using the semiempirical ZINDO/1 quantum mechanical calculations. The potential antibacterial study of the ligands and some metal complexes has been made with one gram positive bacteria Staphylococcus aureus and one gram negative bacteria E. coli which gives encouraging results. Both the Co(II complexes are found to possess monoclinic crystal system.

Characterisation of bare and tannase-loaded calcium alginate beads by microscopic, thermogravimetric, FTIR and XRD analyses.

Science.gov (United States)

Larosa, Claudio; Salerno, Marco; de Lima, Juliana Silva; Merijs Meri, Remo; da Silva, Milena Fernandes; de Carvalho, Luiz Bezerra; Converti, Attilio

2018-08-01

Incorporating enzymes into calcium alginate beads is an effective method to immobilise them and to preserve, at the same time, their catalytic activity. Sodium alginate was mixed with Aspergillus ficuum tannase in aqueous solution, and tannase-loaded calcium alginate beads were prepared using a simple droplet-based microfluidic system. Extensive experimental analysis was carried out to characterise the samples. Microscopic imaging revealed morphological differences between the surfaces of bare alginate matrix and tannase-loaded alginate beads. Thermal analysis allowed assessing the hydration contents of alginate and revealed the presence of tannase entrapped in the loaded beads, which was confirmed by vibrational spectroscopy. X-ray diffraction allowed us to conclude that alginate of tannase-loaded beads is not crystalline, which would make them suitable as carriers for possible controlled release. Moreover, they could be used in food applications to improve tea quality or clarify juices. Copyright © 2018 Elsevier B.V. All rights reserved.

Showing/Sharing: Analysing Visual Communication from a Praxeological Perspective

Directory of Open Access Journals (Sweden)

Maria Schreiber

2017-12-01

Full Text Available This contribution proposes a methodological framework for empirical research into visual practices on social media. The framework identifies practices, pictures and platforms as relevant dimensions of analysis. It is mainly developed within, and is compatible with qualitative, interpretive approaches which focus on visual communication as part of everyday personal communicative practices. Two screenshots from Instagram and Facebook are introduced as empirical examples to investigate collaborative practices of meaning-making relating to pictures on social media. While social media seems to augment reflexive, processual practices of negotiating identities, visual media, in particular, amps up aesthetic, ambivalent and embodied dimensions within these practices.

Thermal transformation of bioactive caffeic acid on fumed silica seen by UV-Vis spectroscopy, thermogravimetric analysis, temperature programmed desorption mass spectrometry and quantum chemical methods.

Science.gov (United States)

Kulik, Tetiana V; Lipkovska, Natalia O; Barvinchenko, Valentyna M; Palyanytsya, Borys B; Kazakova, Olga A; Dudik, Olesia O; Menyhárd, Alfréd; László, Krisztina

2016-05-15

Thermochemical studies of hydroxycinnamic acid derivatives and their surface complexes are important for the pharmaceutical industry, medicine and for the development of technologies of heterogeneous biomass pyrolysis. In this study, structural and thermal transformations of caffeic acid complexes on silica surfaces were studied by UV-Vis spectroscopy, thermogravimetric analysis, temperature programmed desorption mass spectrometry (TPD MS) and quantum chemical methods. Two types of caffeic acid surface complexes are found to form through phenolic or carboxyl groups. The kinetic parameters of the chemical reactions of caffeic acid on silica surface are calculated. The mechanisms of thermal transformations of the caffeic chemisorbed surface complexes are proposed. Thermal decomposition of caffeic acid complex chemisorbed through grafted ester group proceeds via three parallel reactions, producing ketene, vinyl and acetylene derivatives of 1,2-dihydroxybenzene. Immobilization of phenolic acids on the silica surface improves greatly their thermal stability. Copyright © 2016 Elsevier Inc. All rights reserved.

Multi-Scale Carbon Isotopic Analyses Show Allende Nanodiamonds are Mostly Solar with Some PreSolar

Science.gov (United States)

Lewis, J. B.; Isheim, D.; Floss, C.; Gyngard, F.; Seidman, D. N.

2017-07-01

NanoSIMS and atom-probe experiments on different-sized aggregates of meteoritic nanodiamonds show mostly normal C isotopes, with a fraction of 13C-enriched material. The best interpretation is a combination of solar system and supernova formation.

Eucalyptus kraft pulp production: Thermogravimetry monitoring

International Nuclear Information System (INIS)

Barneto, Agustin G.; Vila, Carlos; Ariza, Jose

2011-01-01

Highlights: → Thermogravimetric analysis can be used to monitor the pulping process in a pulp mill. → ECF bleaching process affects the crystalline cellulose volatilization. → The fibre size has an influence on composition and thermal behavior of pulp. - Abstract: Under oxidative environment the thermal degradation of lignocellulosic materials like wood or pulp is sensitive to slight composition changes. For this, in order to complement the chemical and X-ray diffraction results, thermogravimetric analyses (TGA) were used to monitor pulp production in a modern pulp mill. Runs were carried out on crude, oxygen delignified and bleached pulps from three eucalyptus woods from different species and geographical origins. Moreover, with the modeling of thermogravimetric data, it was possible to obtain an approximate composition of samples which includes crystalline and amorphous cellulose. TGA results show that pulping has an intensive effect on bulk lignin and hemicellulose, but it has limited influence on the removal of these substances when they are linked to cellulose microfibril. The stages of oxygen delignification and bleaching, based in chlorine dioxide and hydrogen peroxide, increase the crystalline cellulose volatilization rate. These changes are compatible with a more crystalline microfibril. The influence of the fibre size on pulp composition, crystallinity and thermal degradation behavior was observed.

Thermogravimetric and calorimetric characteristics during co-pyrolysis of municipal solid waste components.

Science.gov (United States)

Ansah, Emmanuel; Wang, Lijun; Shahbazi, Abolghasem

2016-10-01

The thermogravimetric and calorimetric characteristics during pyrolysis of wood, paper, textile and polyethylene terephthalate (PET) plastic in municipal solid wastes (MSW), and co-pyrolysis of biomass-derived and plastic components with and without torrefaction were investigated. The active pyrolysis of the PET plastic occurred at a much higher temperature range between 360°C and 480°C than 220-380°C for the biomass derived components. The plastic pyrolyzed at a heating rate of 10°C/min had the highest maximum weight loss rate of 18.5wt%/min occurred at 420°C, followed by 10.8wt%/min at 340°C for both paper and textile, and 9.9wt%/min at 360°C for wood. At the end of the active pyrolysis stage, the final mass of paper, wood, textile and PET was 28.77%, 26.78%, 21.62% and 18.31%, respectively. During pyrolysis of individual MSW components at 500°C, the wood required the least amount of heat at 665.2J/g, compared to 2483.2J/g for textile, 2059.4J/g for paper and 2256.1J/g for PET plastic. The PET plastic had much higher activation energy of 181.86kJ/mol, compared to 41.47kJ/mol for wood, 50.01kJ/mol for paper and 36.65kJ/mol for textile during pyrolysis at a heating rate of 10°C/min. H2O and H2 peaks were observed on the MS curves for the pyrolysis of three biomass-derived materials but there was no obvious H2O and H2 peaks on the MS curves of PET plastic. There was a significant interaction between biomass and PET plastic during co-pyrolysis if the biomass fraction was dominant. The amount of heat required for the co-pyrolysis of the biomass and plastic mixture increased with the increase of plastic mass fraction in the mixture. Torrefaction at a proper temperature and time could improve the grindability of PET plastic. The increase of torrefaction temperature and time did not affect the temperature where the maximum pyrolytic rates occurred for both biomass and plastic but decreased the maximum pyrolysis rate of biomass and increased the maximum pyrolysis

Approximate analyses of inelastic effects in pipework

International Nuclear Information System (INIS)

Jobson, D.A.

1983-01-01

This presentation shows figures concerned with analyses of inelastic effects in pipework as follows: comparison of experimental and calculated simplified analyses results for free end rotation and for circumferential strain; interrupted stress relaxation; regenerated relaxation caused by reversed yield; buckling of straight pipe under combined bending and torsion; results of fatigues test of pipe bend

Automatic incrementalization of Prolog based static analyses

DEFF Research Database (Denmark)

Eichberg, Michael; Kahl, Matthias; Saha, Diptikalyan

2007-01-01

Modem development environments integrate various static analyses into the build process. Analyses that analyze the whole project whenever the project changes are impractical in this context. We present an approach to automatic incrementalization of analyses that are specified as tabled logic...... programs and evaluated using incremental tabled evaluation, a technique for efficiently updating memo tables in response to changes in facts and rules. The approach has been implemented and integrated into the Eclipse IDE. Our measurements show that this technique is effective for automatically...

Analysing and Comparing Encodability Criteria

Directory of Open Access Journals (Sweden)

Kirstin Peters

2015-08-01

Full Text Available Encodings or the proof of their absence are the main way to compare process calculi. To analyse the quality of encodings and to rule out trivial or meaningless encodings, they are augmented with quality criteria. There exists a bunch of different criteria and different variants of criteria in order to reason in different settings. This leads to incomparable results. Moreover it is not always clear whether the criteria used to obtain a result in a particular setting do indeed fit to this setting. We show how to formally reason about and compare encodability criteria by mapping them on requirements on a relation between source and target terms that is induced by the encoding function. In particular we analyse the common criteria full abstraction, operational correspondence, divergence reflection, success sensitiveness, and respect of barbs; e.g. we analyse the exact nature of the simulation relation (coupled simulation versus bisimulation that is induced by different variants of operational correspondence. This way we reduce the problem of analysing or comparing encodability criteria to the better understood problem of comparing relations on processes.

Fulltext PDF

Indian Academy of Sciences (India)

differential thermal analysis (TG–DTA). ... −2 was observed. Keywords. Ceramics; fuel cells; solid state reactions; electromotive force; ionic conduction. 1. ... thermal analysing balance based on the thermogravimetric/ differential thermal analysis ...

Fulltext PDF

Indian Academy of Sciences (India)

Administrator

UV–Vis spectra and thermogravimetric analyses. This compound ... better opportunity to form hydrogen bond interactions with the ... 2 using the SHELXL 97 software (Sheldrick 1997,. SHELXS-97). .... change in bond angle. The angle ...

Molten salt corrosion behavior of structural materials in LiCl-KCl-UCl3 by thermogravimetric study

Science.gov (United States)

Rao, Ch Jagadeeswara; Ningshen, S.; Mallika, C.; Mudali, U. Kamachi

2018-04-01

The corrosion resistance of structural materials has been recognized as a key issue in the various unit operations such as salt purification, electrorefining, cathode processing and injection casting in the pyrochemical reprocessing of spent metallic nuclear fuels. In the present work, the corrosion behavior of the candidate materials of stainless steel (SS) 410, 2.25Cr-1Mo and 9Cr-1Mo steels was investigated in molten LiCl-KCl-UCl3 salt by thermogravimetric analysis under inert and reactive atmospheres at 500 and 600 °C, for 6 h duration. Insignificant weight gain (less than 1 mg/cm2) in the inert atmosphere and marginal weight gain (maximum 5 mg/cm2) in the reactive atmosphere were observed at both the temperatures. Chromium depletion rates and formation of Cr-rich corrosion products increased with increasing temperature of exposure in both inert and reactive atmospheres as evidenced by SEM and EDS analysis. The corrosion attack by LiCl-KCl-UCl3 molten salt, under reactive atmosphere for 6 h duration was more in the case of SS410 than 9Cr-1Mo steel followed by 2.25Cr-1Mo steel at 500 °C and the corrosion attack at 600 °C followed the order: 9Cr-1Mo steel >2.25Cr-1Mo steel > SS410. Outward diffusion of the minor alloying element, Mo was observed in 9Cr-1Mo and 2.25Cr-1Mo steels at both temperatures under reactive atmosphere. Laser Raman spectral analysis of the molten salt corrosion tested alloys under a reactive atmosphere at 500 and 600 °C for 6 h revealed the formation of unprotected Fe3O4 and α-as well as γ-Fe2O3. The results of the present study facilitate the selection of structural materials for applications in the corrosive molten salt environment at high temperatures.

Development of calcium phosphate based apatite from hen's eggshell

Indian Academy of Sciences (India)

Unknown

2.2d TG–DTA analysis: The weight loss and thermal stability of the samples were also evaluated from the thermogravimetric analysis data. An HETZSCH-Gerate- bau GmBH thermal analyser having simultaneous thermal analyser (STA) 409 C microbalance with a heating rate of 10°C min–1 was employed. 3. Results and ...

Preparation, Investigation and the Study of the Effect of Mn(II Complex of Catechol and 2-Aminopyridine on Seed Germination

Directory of Open Access Journals (Sweden)

F. I. El-Moshaty

2011-01-01

Full Text Available The formation of mixed ligand complex of Mn(II with catechol (L1 and 2-aminopyridine (L2 was determined by elemental analyses (C, H and N, molar conductance measurement, thermogravimetric analysis, infrared, electronic and electron paramagnetic resonance spectroscopies. The elemental analysis data show the formation of 1:1:1 [M: L1: L2] complex. The molar conductance measurement shows a non-electrolyte nature. The thermogravimetric analysis data of the complex display the existence of hydrated and coordinated water molecules. The infrared spectral data exhibit the coordination sites that are through -OH,-C=N and –NH2 groups. The electronic spectral data display the electronic transitions of the ligands and suggest an octahedral structure for the complex. The electron paramagnetic resonance spectrum of the complex reveals the existence of paramagnetic phenomena and supports its geometrical structure. Seed germination and root length of grass were also assayed under the effect of MnCl2.4H2O, catechol, 2-aminopyridine and its complex. Mn(II salt was the most effective on germination than its complex which possess the high test effect on root length, while the ligands are the least active of all.

We're Playing "Jeremy Kyle"! Television Talk Shows in the Playground

Science.gov (United States)

Marsh, Jackie; Bishop, Julia

2014-01-01

This paper focuses on an episode of play in a primary school playground in England, which featured a group of children re-enacting elements of the television talk show "The Jeremy Kyle Show". The episode is analysed in the light of work that has identified the key elements of the talk show genre and the children's play is examined in…

Surface area and pore size characteristics of nanoporous gold subjected to thermal, mechanical, or surface modification studied using gas adsorption isotherms, cyclic voltammetry, thermogravimetric analysis, and scanning electron microscopy

Science.gov (United States)

Tan, Yih Horng; Davis, Jason A.; Fujikawa, Kohki; Ganesh, N. Vijaya; Demchenko, Alexei V.

2012-01-01

Nitrogen adsorption/desorption isotherms are used to investigate the Brunauer, Emmett, and Teller (BET) surface area and Barrett-Joyner-Halenda (BJH) pore size distribution of physically modified, thermally annealed, and octadecanethiol functionalized np-Au monoliths. We present the full adsorption-desorption isotherms for N2 gas on np-Au, and observe type IV isotherms and type H1 hysteresis loops. The evolution of the np-Au under various thermal annealing treatments was examined using scanning electron microscopy (SEM). The images of both the exterior and interior of the thermally annealed np-Au show that the porosity of all free standing np-Au structures decreases as the heat treatment temperature increases. The modification of the np-Au surface with a self-assembled monolayer (SAM) of C18-SH (coverage of 2.94 × 1014 molecules cm−2 based from the decomposition of the C18-SH using thermogravimetric analysis (TGA)), was found to reduce the strength of the interaction of nitrogen gas with the np-Au surface, as reflected by a decrease in the ‘C’ parameter of the BET equation. From cyclic voltammetry studies, we found that the surface area of the np-Au monoliths annealed at elevated temperatures followed the same trend with annealing temperature as found in the BET surface area study and SEM morphology characterization. The study highlights the ability to control free-standing nanoporous gold monoliths with high surface area, and well-defined, tunable pore morphology. PMID:22822294

Design and Characterization of Liquidlike POSS-Based Hybrid Nanomaterials Synthesized via Ionic Bonding and Their Interactions with CO 2

KAUST Repository

Petit, Camille; Lin, Kun-Yi Andrew; Park, Ah-Hyung Alissa

2013-01-01

relevant to CO2 capture, in particular thermal stability, swelling, viscosity, as well as their interactions with CO 2, were investigated using thermogravimetric analyses, differential scanning calorimetry, and NMR and ATR FT-IR spectroscopies. The results

Thermogravimetric Study and Modeling of Direct Sulfation of Limestone by Sulfur Dioxide%二氧化硫对石灰石的直接硫酸盐化作用的热重分析的研究与建模

Institute of Scientific and Technical Information of China (English)

R. Hallaj; M. Nikazar; B. Dabir

2004-01-01

The direct sulfation of limestone from different sources in Iran was studied in a thermogravimetric analyzer under atmospheric pressure. All limestone samples tested have higher than 97% CaCO3. Experimental conditions were as follows: particle size levels ranging from 1.6μm to 7.8μm, four level reaction temperatures (700°C,750°C, 800°C and 850°C), and two SO2 concentrations (2.4 × 10-3 and 3.2 × 10-3 mol.mol-i). The particle size and temperature showed dominant influences on the rate and level of conversion while the effect of SO2 concentration was weak. The shrinking core model can be used to describe the behavior of the sulfation process. The reaction kinetics and diffusion mechanism are both important in controlling the rate of the process. The two key parameters of the model, chemical rate constant Ks and effective diffusion coefficient Deff were obtained. Model predictions are in good agreement with the experimental data.

Chemical Functionalization and Characterization of Cellulose Extracted from Wheat Straw Using Acid Hydrolysis Methodologies

Directory of Open Access Journals (Sweden)

Chemar J. Huntley

2015-01-01

Full Text Available The nonuniform distribution of cellulose into many composite materials is attributed to the hydrogen bonding observed by the three hydroxyl groups located on each glucose monomer. As an alternative, chemical functionalization is performed to disrupt the strong hydrogen bonding behavior without significant altering of the chemical structure or lowering of the thermal stability. In this report, we use wheat straw as the biomass source for the extraction of cellulose and, subsequently, chemical modification via the Albright-Goldman and Jones oxidation reactions. X-ray diffraction analyses reveal that upon oxidation a slight change in the cellulose polymorphic structure (CI to CII can be observed when compared to its unmodified counterpart. Scanning electron microscopy analyses show that the oxidized cellulose structure exhibits fiber-like crystals with lengths and diameters on the micrometer scale. Thermal analyses (differential scanning calorimetry and thermogravimetric analysis show an increase in the thermal stability for the modified cellulose at extremely high temperatures (>300°C.

Syntheses, structures and photoluminescent properties of Zn(Ⅱ)/Co(Ⅱ) coordination polymers based on flexible tetracarboxylate ligand of 5,5′-(butane-1,4-diyl)-bis(oxy)-di isophthalic acid

Energy Technology Data Exchange (ETDEWEB)

Gao, Yan-Peng [Inner Mongolia Key Lab Chem & Phys Rare Earth Mat, College of Chemistry and Chemical Engineering, Inner Mongolia University, Hohhot 010021 (China); Department of Chemistry and Chemical Engineering, Ordos College of Inner Mongolia University, Ordos 017000 (China); Department of Chemistry and Chemical Engineering, Ordos Applied Technology College, Ordos 017000 (China); Guo, Le [Department of Chemistry and Chemical Engineering, Ordos College of Inner Mongolia University, Ordos 017000 (China); Department of Chemistry and Chemical Engineering, Ordos Applied Technology College, Ordos 017000 (China); Dong, Wei; Jia, Min; Zhang, Jing-Xue; Sun, Zhong [Inner Mongolia Key Lab Chem & Phys Rare Earth Mat, College of Chemistry and Chemical Engineering, Inner Mongolia University, Hohhot 010021 (China); Chang, Fei, E-mail: ndchfei@imu.edu.cn [Inner Mongolia Key Lab Chem & Phys Rare Earth Mat, College of Chemistry and Chemical Engineering, Inner Mongolia University, Hohhot 010021 (China)

2016-08-15

Three new mixed-ligand metal-organic frameworks based on 5,5′-(butane-1,4- diyl)-bis(oxy)-diisophthalic acid and transitional metal cations with the help of two ancillary bridging N-donor pyridyl and imidazole linkers, [Zn(L){sub 0.5}(4,4′-bpy)]·2(H{sub 2}O) (1), [M(L){sub 0.5}(bib)]·4(H{sub 2}O) (M = Zn (2), Co (3)), (4,4′-bpy=4,4′–bipyridine, bib=1,4-bis (1H-imidazol-1-yl)-butane), have been synthesized under solvothermal conditions. Their structures and properties were determined by single-crystal and powder X-ray diffraction analyses, IR spectra, elemental analyses and thermogravimetric analyses (TGA). Compounds 1–3 display a 3D 3-fold interpenetrated frameworks linked by the L{sup 4−} ligands, ancillary N-donor linkers and the free water molecules in the crystal lattice. Topological analysis reveals that 1–3 are a (4,4)-connected bbf topology net with the (6{sup 4}·8{sup 2})(6{sup 6}) topology. The effects of the L{sup 4−} anions, the N-donor ligands, and the metal ions on the structures of the coordination polymers have been discussed. Furthermore, luminescence properties and thermogravimetric properties of these compounds were investigated. - Graphical abstract: Three new compounds of MOFs have been prepared and characterized. The luminescence properties and thermogravimetric properties of compounds were investigated. Display Omitted.

A novel method for synthesizing nano-crystalline MgTiO3 geikielite

Indian Academy of Sciences (India)

. ... for 8 h. The ammonium salts were dissolved in double distilled ... thermal analyses and thermogravimetric studies on the sample revealed that the sample is stable up to 700 K and absence of any dehydration or decomposition reaction up.

A Study of the Oxidation Behaviour of Pile Grade A (PGA) Nuclear Graphite Using Thermogravimetric Analysis (TGA), Scanning Electron Microscopy (SEM) and X-Ray Tomography (XRT).

Science.gov (United States)

Payne, Liam; Heard, Peter J; Scott, Thomas B

2015-01-01

Pile grade A (PGA) graphite was used as a material for moderating and reflecting neutrons in the UK's first generation Magnox nuclear power reactors. As all but one of these reactors are now shut down there is a need to understand the residual state of the material prior to decommissioning of the cores, in particular the location and concentration of key radio-contaminants such as 14C. The oxidation behaviour of unirradiated PGA graphite was studied, in the temperature range 600-1050°C, in air and nitrogen using thermogravimetric analysis, scanning electron microscopy and X-ray tomography to investigate the possibility of using thermal degradation techniques to examine 14C distribution within irradiated material. The thermal decomposition of PGA graphite was observed to follow the three oxidation regimes historically identified by previous workers with limited, uniform oxidation at temperatures below 600°C and substantial, external oxidation at higher temperatures. This work demonstrates that the different oxidation regimes of PGA graphite could be developed into a methodology to characterise the distribution and concentration of 14C in irradiated graphite by thermal treatment.

Defect structure, nonstoichiometry, and phase stability of Ca-doped YCrO3

International Nuclear Information System (INIS)

Carini, G.F. II; Anderson, H.U.; Nasrallah, M.M.; Sparlin, D.M.

1991-01-01

The dependence of the defect structure of Ca-doped YCrO 3 on oxygen activity and temperature was investigated by high temperature thermogravimetric measurements. Defect models developed from electrical conductivity data obtained in a previous study were used to interpret the thermogravimetric data. A correlation was found between the electrical conductivity and the thermogravimetric data which suggested that these data were concomitantly dependent on the acceptor dopant and oxygen vacancy dependence of the thermodynamic parameters. Kroeger-Vink type diagrams showing the regions of stability with respect to oxygen activity and temperature were constructed. The TGA data show that Ca-doped YCrO 3 is even more stable toward reduction than doped LaCrO 3

Kinetics of devolatilisation of forestry wastes from thermogravimetric analysis

Energy Technology Data Exchange (ETDEWEB)

Lapuerta, M.; Hernandez, J.J. [Universidad de Castilla-La Mancha, Ciudad real (Spain). Escuela Tecnica Superior de Ingenieros Industriales; Rodriguez, J.J. [Repsol-YPF, Puertollano (Spain). Chemical Department

2004-10-01

The great potential of Maritime pine (Pinus pinaster) wastes in the middle regions of Spain has motivated an increasing interest about the energy use of this material, either through combustion or gasification processes. Samples of these biomass wastes have been analysed by thermogravimetry under both inert and oxidant atmospheres, from room temperature up to 1100 K, at different heating rates: 10, 30, 40, 50 and 60 K min{sup -1}. An estimation of the proximate analysis of the samples was made from combination of both resulting weight loss curves. The devolatilisation process of the samples was divided into three non-interacting mass-loss events described as parallel first-order reactions, being the first event identified as the moisture loss process, the second one as the hemicellulose and cellulose decomposition process and the third one as that of lignin decomposition. A fitting algorithm to obtain the kinetic parameters permitted a good agreement with experimental results, as well as a good discrimination of the effect of the heating rate. Due to the non-homogeneous nature of the tested samples, the use of other conventional methods for obtaining the kinetic parameters has been proved to be inadequate. (author)

Sorption analyses in materials science: selected oxides

International Nuclear Information System (INIS)

Fuller, E.L. Jr.; Condon, J.B.; Eager, M.H.; Jones, L.L.

1981-01-01

Physical adsorption studies have been shown to be extremely valuable in studying the chemistry and structure of dispersed materials. Many processes rely on the access to the large amount of surface made available by the high degree of dispersion. Conversely, there are many applications where consolidation of the dispersed solids is required. Several systems (silica gel, alumina catalysts, mineralogic alumino-silicates, and yttrium oxide plasters) have been studied to show the type and amount of chemical and structural information that can be obtained. Some review of current theories is given and additional concepts are developed based on statistical and thermodynamic arguments. The results are applied to sorption data to show that detailed sorption analyses are extremely useful and can provide valuable information that is difficult to obtain by any other means. Considerable emphasis has been placed on data analyses and interpretation of a nonclassical nature to show the potential of such studies that is often not recognized nor utilized

Comparative study on the pyrolysis behaviour and kinetics of two macroalgae biomass (Gracilaria changii and Gelidium pusillum) by thermogravimetric analysis

Science.gov (United States)

Roslee, A. N.; Munajat, N. F.

2017-10-01

Macroalgae are often referred as seaweed and could be significant biomass resource for the production of numerous energy carriers including biofuels. In this study, the chemical composition of Gracilaria changii (G. changii) and Gelidium pusillum (G. pusillum) were determined through proximate and ultimate analysis and the thermal degradation behaviour of G. changii and G. pusillum were investigated via thermogravimetric analysis (TGA) in determining the important main composition to be considered as biomass fuels. It has found the pyrolysis of G. changii and G. pusillum consists of three stages and stage II is the main decomposition stage with major mass loss of around 52.16% and 44.42%, respectively. The TGA data were then used for determination of kinetic parameters of the pyrolysis process using three model-free methods: Kissinger, Kissinger-Akahira-Sunose (KAS) and Flynn-Wall-Ozawa (FWO). The apparent activation energy calculated by using Kissinger method for G. changii was lower than G. Pusillum, i.e.173.12 kJ/mol and 193.22 kJ/mol, respectively. The activation energies calculated from KAS and FWO methods were increased with increasing the pyrolysis conversion with average activation energies of 172.32 kJ/mol and 181.19 kJ/mol for G. changii while for G. pusillum (177.42 kJ/mol and 187.4 kJ/mol). G. pusillum has lower and wider distribution of activation energy and revealed that the pyrolysis process for G. changii was easier than G. pusillum. These data provide information for further application for designing and modelling in thermochemical conversion system of macroalgae biomass.

A systematic review and meta-Analyses show that carbapenem use and medical devices are the leading risk factors for carbapenem- resistant pseudomonas aeruginosa

NARCIS (Netherlands)

A.F. Voor (Anne); J.A. Severin (Juliëtte); E.M.E.H. Lesaffre (Emmanuel); M.C. Vos (Margreet)

2014-01-01

textabstractA systematic review and meta-Analyses were performed to identify the risk factors associated with carbapenem-resistant Pseudomonas aeruginosa and to identify sources and reservoirs for the pathogen. A systematic search of PubMed and Embase databases from 1 January 1987 until 27 January

Workload analyse of assembling process

Science.gov (United States)

Ghenghea, L. D.

2015-11-01

The workload is the most important indicator for managers responsible of industrial technological processes no matter if these are automated, mechanized or simply manual in each case, machines or workers will be in the focus of workload measurements. The paper deals with workload analyses made to a most part manual assembling technology for roller bearings assembling process, executed in a big company, with integrated bearings manufacturing processes. In this analyses the delay sample technique have been used to identify and divide all bearing assemblers activities, to get information about time parts from 480 minutes day work time that workers allow to each activity. The developed study shows some ways to increase the process productivity without supplementary investments and also indicated the process automation could be the solution to gain maximum productivity.

Analysing harmonic motions with an iPhone’s magnetometer

Science.gov (United States)

Yavuz, Ahmet; Kağan Temiz, Burak

2016-05-01

In this paper, we propose an experiment for analysing harmonic motion using an iPhone’s (or iPad’s) magnetometer. This experiment consists of the detection of magnetic field variations obtained from an iPhone’s magnetometer sensor. A graph of harmonic motion is directly displayed on the iPhone’s screen using the Sensor Kinetics application. Data from this application was analysed with Eureqa software to establish the equation of the harmonic motion. Analyses show that the use of an iPhone’s magnetometer to analyse harmonic motion is a practical and effective method for small oscillations and frequencies less than 15-20 Hz.

A Simple, Reliable Precision Time Analyser

Energy Technology Data Exchange (ETDEWEB)

Joshi, B. V.; Nargundkar, V. R.; Subbarao, K.; Kamath, M. S.; Eligar, S. K. [Atomic Energy Establishment Trombay, Bombay (India)

1966-06-15

A 30-channel time analyser is described. The time analyser was designed and built for pulsed neutron research but can be applied to other uses. Most of the logic is performed by means of ferrite memory core and transistor switching circuits. This leads to great versatility, low power consumption, extreme reliability and low cost. The analyser described provides channel Widths from 10 {mu}s to 10 ms; arbitrarily wider channels are easily obtainable. It can handle counting rates up to 2000 counts/min in each channel with less than 1% dead time loss. There is a provision for an initial delay equal to 100 channel widths. An input pulse de-randomizer unit using tunnel diodes ensures exactly equal channel widths. A brief description of the principles involved in core switching circuitry is given. The core-transistor transfer loop is compared with the usual core-diode loops and is shown to be more versatile and better adapted to the making of a time analyser. The circuits derived from the basic loop are described. These include the scale of ten, the frequency dividers and the delay generator. The current drivers developed for driving the cores are described. The crystal-controlled clock which controls the width of the time channels and synchronizes the operation of the various circuits is described. The detector pulse derandomizer unit using tunnel diodes is described. The scheme of the time analyser is then described showing how the various circuits can be integrated together to form a versatile time analyser. (author)

Surface modification of hydroxyapatite with poly(methyl methacrylate) via surface-initiated ATRP

Energy Technology Data Exchange (ETDEWEB)

Wang Yan; Zhang Xi; Yan Jinliang; Xiao Yan [Shanghai Key Laboratory of Advanced Polymeric Materials, Key Laboratory for Ultrafine Materials of Ministry of Education, School of Materials Science and Engineering, East China University of Science and Technology, 130 Meilong Road, Shanghai 200237 (China); Lang Meidong, E-mail: mdlang@ecust.edu.cn [Shanghai Key Laboratory of Advanced Polymeric Materials, Key Laboratory for Ultrafine Materials of Ministry of Education, School of Materials Science and Engineering, East China University of Science and Technology, 130 Meilong Road, Shanghai 200237 (China)

2011-05-01

This article describes the fabrication of hydroxyapatite (HAP) nanocomposites grafted with poly(methyl methacrylate) (PMMA). Surface-initiated atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) was carried out from hydroxyapatite particles derivatized with ATRP initiators. The structure and properties of the nanocomposites were investigated by thermogravimetric analysis (TGA), transmission electron microscopy (TEM), differential scanning calorimeter (DSC) measurements, and contact angle analyses. TGA was used to estimate the grafting density of ATRP initiators (0.49 initiator/nm{sup 2}) and the amount of grafted PMMA on the HAP surface. The contact angle analyses indicated that grafting PMMA onto the HAP surface dramatically increased the hydrophobicity of the surface. Moreover, the HAP nanocomposites showed excellent dispersibility in both aqueous solution and organic solvent.

Surface modification of hydroxyapatite with poly(methyl methacrylate) via surface-initiated ATRP

International Nuclear Information System (INIS)

Wang Yan; Zhang Xi; Yan Jinliang; Xiao Yan; Lang Meidong

2011-01-01

This article describes the fabrication of hydroxyapatite (HAP) nanocomposites grafted with poly(methyl methacrylate) (PMMA). Surface-initiated atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) was carried out from hydroxyapatite particles derivatized with ATRP initiators. The structure and properties of the nanocomposites were investigated by thermogravimetric analysis (TGA), transmission electron microscopy (TEM), differential scanning calorimeter (DSC) measurements, and contact angle analyses. TGA was used to estimate the grafting density of ATRP initiators (0.49 initiator/nm 2 ) and the amount of grafted PMMA on the HAP surface. The contact angle analyses indicated that grafting PMMA onto the HAP surface dramatically increased the hydrophobicity of the surface. Moreover, the HAP nanocomposites showed excellent dispersibility in both aqueous solution and organic solvent.

IN SITU AND POST REACTION COBALT-INCORPORATION INTO ...

African Journals Online (AJOL)

a

confirmed by Raman spectroscopy and UV-vis diffuse reflectance .... Pyris 1 TGA Thermogravimetric analyser using nitrogen or air as the purge gas at a heating rate ... The laser spot size on the sample was ~1.5 microns in diameter, and the ...

Solid state syntheses and interconversion of new metal salts and ...

African Journals Online (AJOL)

... dehydrochlorinated via thermal or mechanochemical methods to obtain the coordination compounds [MCl2(H2biim)]. X-ray single crystal structure determination, powder diffraction (XRDP), thermogravimetric and elemental analyses were used in the preliminary characterization of the new salts and the derived materials.

Structural characterization and evaluation of the antioxidant activities of polysaccharides extracted from Qingzhuan brick tea.

Science.gov (United States)

Yang, Xinhe; Huang, Mingjun; Qin, Caiqin; Lv, Bangyu; Mao, Qingli; Liu, Zhonghua

2017-08-01

The crude tea polysaccharides (CTPS) from Qingzhuan brick tea(QZBT) were extracted and fractionated to afford two fractions, namely TPS-1 and TPS-2. Analyses were conducted concerning the structural characterization and antioxidant activities of these samples. Component analysis revealed that the carbohydrate, uronic acid, protein and polyphenol contents of these samples differed significantly. Fourier transform infrared analysis showed that these samples showed similar characteristic absorption peaks for polysaccharides. Ultraviolet-visible spectroscopy, circular dichroism, scanning electron microscopy and thermogravimetric analyses indicated that there were considerable differences in the presence of protein, surface features, conformational characteristics and thermodynamic behaviors. For antioxidant activities in vitro, CTPS, TPS-1 and TPS-2 exhibited concentration-dependent antioxidant activities, with TPS-2 showing significantly higher antioxidant activity than CTPS and TPS-1. These results provide a scientific and strong foundation for the use of tea polysaccharides(TPS) from QZBT and further research towards the relationships between the characteristics and antioxidant activities of TPS. Copyright © 2017 Elsevier B.V. All rights reserved.

Recriticality analyses for CAPRA cores

International Nuclear Information System (INIS)

Maschek, W.; Thiem, D.

1995-01-01

The first scoping calculation performed show that the energetics levels from recriticalities in CAPRA cores are in the same range as in conventional cores. However, considerable uncertainties exist and further analyses are necessary. Additional investigations are performed for the separation scenarios of fuel/steel/inert and matrix material as a large influence of these processes on possible ramp rates and kinetics parameters was detected in the calculations. (orig./HP)

Recriticality analyses for CAPRA cores

Energy Technology Data Exchange (ETDEWEB)

Maschek, W.; Thiem, D.

1995-08-01

The first scoping calculation performed show that the energetics levels from recriticalities in CAPRA cores are in the same range as in conventional cores. However, considerable uncertainties exist and further analyses are necessary. Additional investigations are performed for the separation scenarios of fuel/steel/inert and matrix material as a large influence of these processes on possible ramp rates and kinetics parameters was detected in the calculations. (orig./HP)

Network class superposition analyses.

Directory of Open Access Journals (Sweden)

Carl A B Pearson

Full Text Available Networks are often used to understand a whole system by modeling the interactions among its pieces. Examples include biomolecules in a cell interacting to provide some primary function, or species in an environment forming a stable community. However, these interactions are often unknown; instead, the pieces' dynamic states are known, and network structure must be inferred. Because observed function may be explained by many different networks (e.g., ≈ 10(30 for the yeast cell cycle process, considering dynamics beyond this primary function means picking a single network or suitable sample: measuring over all networks exhibiting the primary function is computationally infeasible. We circumvent that obstacle by calculating the network class ensemble. We represent the ensemble by a stochastic matrix T, which is a transition-by-transition superposition of the system dynamics for each member of the class. We present concrete results for T derived from boolean time series dynamics on networks obeying the Strong Inhibition rule, by applying T to several traditional questions about network dynamics. We show that the distribution of the number of point attractors can be accurately estimated with T. We show how to generate Derrida plots based on T. We show that T-based Shannon entropy outperforms other methods at selecting experiments to further narrow the network structure. We also outline an experimental test of predictions based on T. We motivate all of these results in terms of a popular molecular biology boolean network model for the yeast cell cycle, but the methods and analyses we introduce are general. We conclude with open questions for T, for example, application to other models, computational considerations when scaling up to larger systems, and other potential analyses.

Neoliberalism in education: Five images of critical analyses

Directory of Open Access Journals (Sweden)

Branislav Pupala

2011-03-01

Full Text Available The survey study brings information about the way that educational researchcopes with neoliberalism as a generalized form of social government in the currentwestern culture. It shows that neoliberalism is considered as a universal scope of otherchanges in the basic segments of education and those theoretical and critical analyses ofthis phenomenon represent an important part of production in the area of educationalresearch. It emphasizes the contribution of formation and development of the socalledgovernmental studies for comprehension of mechanisms and consequences ofneoliberal government of the society and shows how way the methodology of thesestudies helps to identify neoliberal strategies used in the regulation of social subjectsby education. There are five selected segments of critical analyses elaborated (fromthe concept of a lifelong learning, through preschool and university education to theeducation of teachers and PISA project that obviously show ideological and theoreticalcohesiveness of the education analysis through the scope of neoliberal governmentality.

DMPD: Structural and functional analyses of bacterial lipopolysaccharides. [Dynamic Macrophage Pathway CSML Database

Lifescience Database Archive (English)

Full Text Available 12106784 Structural and functional analyses of bacterial lipopolysaccharides. Carof...html) (.csml) Show Structural and functional analyses of bacterial lipopolysaccharides. PubmedID 12106784 Title Structural and functi...onal analyses of bacterial lipopolysaccharides. Authors

Study of Selected Composites Copper Concentrate-Plastic Waste Using Thermal Analysis

Science.gov (United States)

Szyszka, Danuta

2017-12-01

The paper presents thermal analysis of selected composites (copper concentrate, plastic waste) in two stages. The first stage consisted in thermogravimetric analysis and differential thermal analysis on the applied plastic waste and copper concentrate, and subsequently, a comparative study has been carried out on products obtained, constituting composites of those materials. As a result of analyses, it was found that up to ca. 400 °C composites show high thermal stability, whereas above that temperature, a thermal decomposition of the composite occurs, resulting in emissions of organic compounds, i.e. hydrocarbon compounds and organic oxygenate derivatives.

Extraction and Characterization of Nano cellulose from Coconut Fiber

International Nuclear Information System (INIS)

Nor Liyana Ahmad; Ishak Ahmad

2013-01-01

Coconut husk fibers has been modified by some chemical treatments to extract cellulose nano crystals (CNC), which are alkali treatment, bleaching and acid hydrolysis using concentrated sulphuric acid. The effect of the treatments on the coconut husk fibers has been analysed using Fourier transform infrared (FTIR) and X-Ray diffraction (XRD). Meanwhile, the morphology observation and thermal stability of the fiber have been analysed by scanning electron microscopy (SEM) and thermogravimetric analysis (TGA) respectively. The analyses show that the chemical modification could eliminate some of the lignin and hemicelluloses of the fiber. Nano cellulose extracted from acid hydrolysis has been analysed using transmission electron microscopy (TEM) to define the size of extracted nano cellulose. The cellulose nano crystals from coconut fibre has the average diameter and length in the range 13.7±6.2 nm and 172.3±8.4 nm, respectively. The obtained nano cellulose may have the potential applications in the fields of biomedical, oil adsorption, membrane, pharmaceutical and bio composites. (author)

Revised final report for tank 241-AN-101, grab samples 1AN-95-1 through 1AN-95-7. Revision 1

International Nuclear Information System (INIS)

Esch, R.A.

1996-01-01

Six supernate grab samples and one field blank were taken from tank 241-AN-101. This report documents analyses performed in support of the Safety Screening program: differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), density by specific gravity (Sp.G.), and total alpha activity (AT)

Synthesis, characterization, biological and electrical conductivity ...

African Journals Online (AJOL)

All the complexes have been characterized on the basis of elemental analyses, magnetic susceptibility measurement, electronic and IR spectra and thermogravimetric analysis. The IR spectral data suggested that the ligands behave as dibasic tridentate moiety towards the central metal ion coordinating through phenolic ...

Synthesis and characterization of thermally stable oligomer-metal ...

African Journals Online (AJOL)

The thermal stabilities of the oligomer-metal complexes were compared by thermogravimetric (TG) and differential thermal (DTA) analyses. According to TG, oligomer-metal complexes were stable against to temperature and thermooxidative decomposition. The weight losses of oligomer-metal complexes were found to be 5 ...

Do men and women show love differently in marriage?

Science.gov (United States)

Schoenfeld, Elizabeth A; Bredow, Carrie A; Huston, Ted L

2012-11-01

In Western societies, women are considered more adept than men at expressing love in romantic relationships. Although scholars have argued that this view of love gives short shrift to men's ways of showing love (e.g., Cancian, 1986; Noller, 1996), the widely embraced premise that men and women "love differently" has rarely been examined empirically. Using data collected at four time points over 13 years of marriage, the authors examined whether love is associated with different behaviors for husbands and wives. Multilevel analyses revealed that, counter to theoretical expectations, both genders were equally likely to show love through affection. But whereas wives expressed love by enacting fewer negative or antagonistic behaviors, husbands showed love by initiating sex, sharing leisure activities, and doing household work together with their wives. Overall, the findings indicate that men and women show their love in more nuanced ways than cultural stereotypes suggest.

Homeopathy: meta-analyses of pooled clinical data.

Science.gov (United States)

Hahn, Robert G

2013-01-01

In the first decade of the evidence-based era, which began in the mid-1990s, meta-analyses were used to scrutinize homeopathy for evidence of beneficial effects in medical conditions. In this review, meta-analyses including pooled data from placebo-controlled clinical trials of homeopathy and the aftermath in the form of debate articles were analyzed. In 1997 Klaus Linde and co-workers identified 89 clinical trials that showed an overall odds ratio of 2.45 in favor of homeopathy over placebo. There was a trend toward smaller benefit from studies of the highest quality, but the 10 trials with the highest Jadad score still showed homeopathy had a statistically significant effect. These results challenged academics to perform alternative analyses that, to demonstrate the lack of effect, relied on extensive exclusion of studies, often to the degree that conclusions were based on only 5-10% of the material, or on virtual data. The ultimate argument against homeopathy is the 'funnel plot' published by Aijing Shang's research group in 2005. However, the funnel plot is flawed when applied to a mixture of diseases, because studies with expected strong treatments effects are, for ethical reasons, powered lower than studies with expected weak or unclear treatment effects. To conclude that homeopathy lacks clinical effect, more than 90% of the available clinical trials had to be disregarded. Alternatively, flawed statistical methods had to be applied. Future meta-analyses should focus on the use of homeopathy in specific diseases or groups of diseases instead of pooling data from all clinical trials. © 2013 S. Karger GmbH, Freiburg.

A kinetic rate expression for the time-dependent coke formation rate during propane dehydrogenation over a platinum alumina monolithic catalyst

NARCIS (Netherlands)

Sint Annaland, van M.; Kuipers, J.A.M.; van Swaaij, W.P.M.

2001-01-01

Coke formation rates under propane dehydrogenation reaction conditions on a used monolithic Pt/¿-Al2O3 catalyst have been experimentally determined in a thermogravimetric analyser (TGA) as a function of time on stream covering wide temperature and concentration ranges. For relatively short times on

A kinetic rate expression for the time-dependent coke formation rate during propane dehydrogenation over a platinum alumina monolithic catalyst.

NARCIS (Netherlands)

van Sint Annaland, M.; Kuipers, J.A.M.; van Swaaij, Willibrordus Petrus Maria

2001-01-01

Coke formation rates under propane dehydrogenation reaction conditions on a used monolithic Pt/y-Al2O3 catalyst have been experimentally determined in a thermogravimetric analyser (TGA) as a function of time on stream covering wide temperature and concentration ranges. For relatively short times on

Analysing User Lifetime in Voluntary Online Collaboration

DEFF Research Database (Denmark)

McHugh, Ronan; Larsen, Birger

2010-01-01

This paper analyses persuasion in online collaboration projects. It introduces a set of heuristics that can be applied to such projects and combines these with a quantitative analysis of user activity over time. Two example sites are studies, Open Street Map and The Pirate Bay. Results show that ...

Hybrid Logical Analyses of the Ambient Calculus

DEFF Research Database (Denmark)

Bolander, Thomas; Hansen, Rene Rydhof

2010-01-01

In this paper, hybrid logic is used to formulate three control flow analyses for Mobile Ambients, a process calculus designed for modelling mobility. We show that hybrid logic is very well-suited to express the semantic structure of the ambient calculus and how features of hybrid logic can...

Thermogravimetric analysis, kinetic study, and pyrolysis-GC/MS analysis of 1,1'-azobis-1,2,3-triazole and 4,4'-azobis-1,2,4-triazole.

Science.gov (United States)

Jia, Chenhui; Li, Yuchuan; Zhang, Shujuan; Fei, Teng; Pang, Siping

2018-03-01

In general, the greater the number of directly linked nitrogen atoms in a molecule, the better its energetic performance, while the stability will be accordingly lower. But 1,1'-azobis-1,2,3-triazole (1) and 4,4'-azobis-1,2,4-triazole (2) show remarkable properties, such as high enthalpies of formation, high melting points, and relatively high stabilities. In order to rationalize this unexpected behavior of the two compounds, it is necessary to study their thermal decompositions and pyrolyses. Although a great deal of research has been focused on the synthesis and characterization of energetic materials with 1 and 2 as the backbone, a complete report on their fundamental thermodynamic parameters and thermal decomposition properties has not been published. Thermogravimetric-differential scanning calorimetry were used to obtain the thermal decomposition data of the title compounds. Kissinger and Ozawa-Doyle methods, the two selected non-isothermal methods, are presented for analysis of the solid-state kinetic data. Pyrolysis-gas chromatography/mass spectrometry was used to study the pyrolysis process of the title compounds. The DSC curves show that the thermal decompositions of 1 and 2 are at different heating rates involved a single exothermic process. The TG curves provide insight into the total weight losses from the compounds associated with this process. At different pyrolysis temperatures, the compositions and types of the pyrolysis products differ greatly and the pyrolysis reaction at 500 °C is more thorough than 400 °C. Apparent activation energies (E) and pre-exponential factors (lnA/s -1 ) are 291.4 kJ mol -1 and 75.53 for 1; 396.2 kJ mol -1 and 80.98 for 2 (Kissinger). The values of E are 284.5 kJ mol -1 for 1 and 386.1 kJ mol -1 for 2 (Ozawa-Doyle). The critical temperature of thermal explosion (T b ) is evaluated as 187.01 °C for 1 and 282.78 °C for 2. The title compounds were broken into small fragment ions under the pyrolysis conditions

Preparation of thermally stable nanocrystalline hydroxyapatite by hydrothermal method.

Science.gov (United States)

Prakash Parthiban, S; Elayaraja, K; Girija, E K; Yokogawa, Y; Kesavamoorthy, R; Palanichamy, M; Asokan, K; Narayana Kalkura, S

2009-12-01

Thermally stable hydroxyapatite (HAp) was synthesized by hydrothermal method in the presence of malic acid. X-ray diffraction (XRD), Fourier transform infra-red spectroscopy (FT-IR), Raman spectroscopy, scanning electron microscopy (SEM), differential thermal analysis (DTA), thermogravimetric analysis (TGA) was done on the synthesized powders. These analyses confirmed the sample to be free from impurities and other phases of calcium phosphates, and were of rhombus morphology along with nanosized particles. IR and Raman analyses indicated the adsorption of malic acid on HAp. Thermal stability of the synthesized HAp was confirmed by DTA and TGA. The synthesized powders were thermally stable upto 1,400 degrees C and showed no phase change. The proposed method might be useful for producing thermally stable HAp which is a necessity for high temperature coating applications.

Bacterial Cellulose-Hydroxyapatite Nanocomposites for Bone Regeneration

Directory of Open Access Journals (Sweden)

S. Saska

2011-01-01

Full Text Available The aim of this study was to develop and to evaluate the biological properties of bacterial cellulose-hydroxyapatite (BC-HA nanocomposite membranes for bone regeneration. Nanocomposites were prepared from bacterial cellulose membranes sequentially incubated in solutions of CaCl2 followed by Na2HPO4. BC-HA membranes were evaluated in noncritical bone defects in rat tibiae at 1, 4, and 16 weeks. Thermogravimetric analyses showed that the amount of the mineral phase was 40%–50% of the total weight. Spectroscopy, electronic microscopy/energy dispersive X-ray analyses, and X-ray diffraction showed formation of HA crystals on BC nanofibres. Low crystallinity HA crystals presented Ca/P a molar ratio of 1.5 (calcium-deficient HA, similar to physiological bone. Fourier transformed infrared spectroscopy analysis showed bands assigned to phosphate and carbonate ions. In vivo tests showed no inflammatory reaction after 1 week. After 4 weeks, defects were observed to be completely filled in by new bone tissue. The BC-HA membranes were effective for bone regeneration.

PWR plant transient analyses using TRAC-PF1

International Nuclear Information System (INIS)

Ireland, J.R.; Boyack, B.E.

1984-01-01

This paper describes some of the pressurized water reactor (PWR) transient analyses performed at Los Alamos for the US Nuclear Regulatory Commission using the Transient Reactor Analysis Code (TRAC-PF1). Many of the transient analyses performed directly address current PWR safety issues. Included in this paper are examples of two safety issues addressed by TRAC-PF1. These examples are pressurized thermal shock (PTS) and feed-and-bleed cooling for Oconee-1. The calculations performed were plant specific in that details of both the primary and secondary sides were modeled in addition to models of the plant integrated control systems. The results of these analyses show that for these two transients, the reactor cores remained covered and cooled at all times posing no real threat to the reactor system nor to the public

Thermogravimetric experiments with titanium

International Nuclear Information System (INIS)

Porter, L.J.; Longhurst, G.R.

1991-02-01

In the process of preparing for pyrophoricity experiments involving uranium, we conducted hydriding and air-exposure experiments on titanium. In these experiments the hydriding reactions and response to air-exposure was generally within the range expected based on work reported by others. One aberrant behavior was a sudden weight gain followed by a significant weight loss. We speculate that loss may be due to hydrogen evolution from the TiH 2 resulting from local heating by oxidation reactions. We verified that titanium is not pyrophoric at temperatures less than 750 degree C. 18 refs. 1 fig

Towards understanding the thermoanalysis of water sorption on lithium orthosilicate (Li4SiO4)

International Nuclear Information System (INIS)

Ortiz-Landeros, J.; Martinez-dlCruz, L.; Gomez-Yanez, C.; Pfeiffer, H.

2011-01-01

A systematic thermogravimetric study of hygroscopic and reactivity behaviors, at low temperatures of lithium orthosilicate (Li 4 SiO 4 ), are presented. Li 4 SiO 4 sample was prepared by solid-state reaction and then treated at different temperature-humidity conditions. Li 4 SiO 4 samples previously treated under different temperature-humidity conditions were characterized by Fourier transform infrared spectroscopy and thermogravimetric analyses. Different processes, adsorption and absorption, take place between the Li 4 SiO 4 and water vapor. Absorbed water produces superficial hydroxylated species such as Si-OH and Li-OH. In addition, a kinetic analysis was performed, and the different water absorption activation enthalpies were calculated. It was found that activation enthalpy (ΔH) values decrease when the relative humidity is incremented, from 5528.6 J/mol to 2074.2 J/mol at relative humidity levels of 60% and 75% respectively. These results show the impact of different humidity and temperature conditions on the stability and/or chemical reactivity of Li 4 SiO 4 , if this ceramic is used in different application fields, such as carbon dioxide captor or as a breeder ceramic into the fusion reactors.

Synergistic Flame Retardancy of Aluminium Dipropylphosphinate and Melamine in Polyamide 6

Directory of Open Access Journals (Sweden)

Linsheng Tang

2013-01-01

Full Text Available The synergistic flame retardancy of aluminium dipropylphosphinate (ADPP and melamine (ME in polyamide 6 (PA6 was studied by the limiting oxygen index (LOI measurement, the vertical burning test, and the cone calorimeter test, and the mechanism was also discussed by thermogravimetric and residual analyses. The experimental results indicated that there was obvious synergistic flame retardancy between ADPP and ME under their appropriate weight ratios. The thermogravimetric results and the analysis of the residues obtained in cone calorimeter test showed that ADPP and ADPP/ME played the role of flame retardance by gaseous- and condensed-phase mechanisms, where, on one hand, they were decomposed into nonvolatile aluminum phosphate and promoted the carbonization of PA6, and the formed intumescent layer resulted in flame retardancy by the barrier effect on heat, air, and decomposition products, and on the other hand, they were decomposed into volatile phosphorus compounds which bring about flame retardancy by flame inhibition. Using a combination of ADPP and ME improved charring of PA6 and raised the residual rate of P and Al, thus, improving the barrier effect in the condensed phase.

Passive safety injection experiments and analyses (PAHKO)

International Nuclear Information System (INIS)

Tuunanen, J.

1998-01-01

PAHKO project involved experiments on the PACTEL facility and computer simulations of selected experiments. The experiments focused on the performance of Passive Safety Injection Systems (PSIS) of Advanced Light Water Reactors (ALWRs) in Small Break Loss-Of-Coolant Accident (SBLOCA) conditions. The PSIS consisted of a Core Make-up Tank (CMT) and two pipelines (Pressure Balancing Line, PBL, and Injection Line, IL). The examined PSIS worked efficiently in SBLOCAs although the flow through the PSIS stopped temporarily if the break was very small and the hot water filled the CMT. The experiments demonstrated the importance of the flow distributor in the CMT to limit rapid condensation. The project included validation of three thermal-hydraulic computer codes (APROS, CATHARE and RELAP5). The analyses showed the codes are capable to simulate the overall behaviour of the transients. The detailed analyses of the results showed some models in the codes still need improvements. Especially, further development of models for thermal stratification, condensation and natural circulation flow with small driving forces would be necessary for accurate simulation of the PSIS phenomena. (orig.)

Synthesis and structural characterization of nickel(II), cobalt(II), Zinc(II), manganese(II), cadmium(II) and uranium(VI) complexes of α-oximinoacetoacet-o/p-anisidide thiosemicarbazone

International Nuclear Information System (INIS)

Patel, P.S.; Patel, M.M.; Ray, R.M.

1993-01-01

A few metal complexes of α-oximinoacetoacet-o/p-anisidide thiosemicarbazones (OAOATS)/(OAPATS) with Ni(II), Co(II), Zn(II), Mn(II), Hg(II), Cd(II) and UO 2 (II) have been prepared and characterized by elemental analyses, conductivity, differential scanning calorimetry study, thermogravimetric analyses and infrared and electronic spectral measurements in conjunction with magnetic susceptibility measurements at room temperature. They have also been tested for their antimicrobial activities. (author). 24 refs., 2 tabs

Simulation-based Investigations of Electrostatic Beam Energy Analysers

CERN Document Server

Pahl, Hannes

2015-01-01

An energy analyser is needed to measure the beam energy profile behind the REX-EBIS at ISOLDE. The device should be able to operate with an accuracy of 1 V at voltages up to 30 kV. In order to find a working concept for an electrostatic energy analyser different designs were evaluated with simulations. A spherical device and its design issues are presented. The potential deformation effects of grids at high voltages and their influence on the energy resolution were investigated. First tests were made with a grid-free ring electrode device and show promising results.

Special analyses reveal coke-deposit structure

International Nuclear Information System (INIS)

Albright, L.F.

1988-01-01

A scanning electron microscope (SEM) and an energy dispersive X-ray analyzer (EDAX) have been used to obtain information that clarifies the three mechanisms of coke formation in ethylene furnaces, and to analyze the metal condition at the exit of furnace. The results can be used to examine furnace operations and develop improved ethylene plant practices. In this first of four articles on the analyses of coke and metal samples, the coking mechanisms and coke deposits in a section of tube from an actual ethylene furnace (Furnace A) from a plant on the Texas Gulf Coast are discussed. The second articles in the series will analyze the condition of the tube metal in the same furnace. To show how coke deposition and metal condition dependent on the operating parameters of an ethylene furnace, the third article in the series will show the coke deposition in a Texas Gulf Coast furnace tube (Furnace B) that operated at shorter residence time. The fourth article discusses the metal condition in that furnace. Some recommendations, based on the analyses and findings, are offered in the fourth article that could help extend the life of ethylene furnace tubes, and also improve overall ethylene plant operations

Synthesis and characterization of the Rhodium (II) citrate complex

International Nuclear Information System (INIS)

Najjar, R.; Santos, F.S. dos; Seidel, W.

1987-01-01

The preparation and characterization of the rhodium (II) citrate is described. Rhodium citrate was prepared by reacting citric acid trihydrated (3,4 g, 16 mmols) with anhydrous rhodium acetate (0,44 g, 1 mmol). Th electronic instruments, thermogravimetric curve and spectrum of rhodium (II) citrate are analysed. (M.J.C.) [pt

Coating of carbon short fibers with thin ceramic layers by chemical vapor deposition

International Nuclear Information System (INIS)

Hackl, Gerrit; Gerhard, Helmut; Popovska, Nadejda

2006-01-01

Carbon short fiber bundles with a length of 6 mm were uniformly coated using specially designed, continuous chemical vapor deposition (CVD) equipment. Thin layers of titanium nitride, silicon nitride (SiC) and pyrolytic carbon (pyC) were deposited onto several kilograms of short fibers in this large scale CVD reactor. Thermo-gravimetric analyses and scanning electron microscopy investigations revealed layer thicknesses between 20 and 100 nm on the fibers. Raman spectra of pyC coated fibers show a change of structural order depending on the CVD process parameters. For the fibers coated with SiC, Raman investigations showed a deposition of amorphous SiC. The coated carbon short fibers will be applied as reinforcing material in composites with ceramic and metallic matrices

Preparation and characterization of bentonite organo clay

International Nuclear Information System (INIS)

Bertagnolli, C.; Almeida Neto, A.F.; Silva, M.G.C.

2009-01-01

Bentonite clays organically modified have great potential use for environmental remediation, especially in the separation of organic compounds from the water. The aim of this work was the preparation of organophilic clays from 'Verde-Lodo' bentonite clay with the quaternary ammonium salts cetyl-pyridinium chloride and benzalkonium chloride. The materials obtained were characterized by XRD, thermogravimetric analyses, Helium picnometry, SEM and energy dispersive X-ray techniques. The results show consistently successful synthesis of the organoclay through the increase in the basal spacing, as well as salt elimination picks and presence of carbon and chlorine in the modified clays; they are inexistent elements in the natural clay. (author)

Preparation and characterization of bentonite organo clay; Preparacao de caracterizacao de argilas bentonitas organofilicas

Energy Technology Data Exchange (ETDEWEB)

Bertagnolli, C.; Almeida Neto, A.F. [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Fac. de Engenharia Quimica. Lab. de Engenharia Ambiental; Silva, M.G.C., E-mail: meuris@feq.unicamp.b [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Fac. de Engenharia Quimica

2009-07-01

Bentonite clays organically modified have great potential use for environmental remediation, especially in the separation of organic compounds from the water. The aim of this work was the preparation of organophilic clays from 'Verde-Lodo' bentonite clay with the quaternary ammonium salts cetyl-pyridinium chloride and benzalkonium chloride. The materials obtained were characterized by XRD, thermogravimetric analyses, Helium picnometry, SEM and energy dispersive X-ray techniques. The results show consistently successful synthesis of the organoclay through the increase in the basal spacing, as well as salt elimination picks and presence of carbon and chlorine in the modified clays; they are inexistent elements in the natural clay. (author)

Developing Characterization Procedures for Qualifying both Novel Selective Laser Sintering Polymer Powders and Recycled Powders

Energy Technology Data Exchange (ETDEWEB)

Bajric, Sendin [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-09-12

Selective laser sintering (SLS) is an additive technique which is showing great promise over conventional manufacturing techniques. SLS requires certain key material properties for a polymer powder to be successfully processed into an end-use part, and therefore limited selection of materials are available. Furthermore, there has been evidence of a powder’s quality deteriorating following each SLS processing cycle. The current investigation serves to build a path forward in identifying new SLS powder materials by developing characterization procedures for identifying key material properties as well as for detecting changes in a powder’s quality. Thermogravimetric analyses, differential scanning calorimetry, and bulk density measurements were investigated.

Comparative study on microwave and conventional hydrothermal pretreatment of bamboo sawdust: Hydrochar properties and its pyrolysis behaviors

International Nuclear Information System (INIS)

Dai, Leilei; He, Chao; Wang, Yunpu; Liu, Yuhuan; Yu, Zhenting; Zhou, Yue; Fan, Liangliang; Duan, Dengle

2017-01-01

Highlights: • Two pretreatments affect differently the hydrochar properties and its pyrolysis behaviors. • Hydrochar by conventional hydrothermal pretreatment shows higher thermal stability. • Microwave hydrothermal pretreatment removes more acetyl. • Hydrochar by microwave hydrothermal pretreatment produces more glucopyranose and less acids. - Abstract: Comparative study on microwave and conventional hydrothermal pretreatment of bamboo sawdust was carried out in this study. Microwave and conventional hydrothermal pretreatment both improved the hydrochar properties and its pyrolysis behaviors. Proximate and elemental analyses show that the properties of hydrochar from microwave hydrothermal pretreatment are better than conventional hydrothermal pretreatment in terms of calorific value and oxygen content except for 150 °C. Microwave hydrothermal pretreatment removes more acetyl groups in hemicellulose compared to conventional hydrothermal pretreatment, which may be attributed to the hot spot effect of microwave irradiation. The peaks of thermogravimetric and derivative thermogravimetric curves of pretreated samples always shifted to higher temperature region. Also, the conventional hydrothermal pretreated samples are more thermally stable than those by microwave heating. In addition, the glucopyranose content in pyrolysis vapors of microwave hydrothermal pretreated bamboo sawdust (190 °C) was 9.82% higher than that from conventional hydrothermal pretreated bamboo sawdust. However, the acids content from microwave hydrothermal pretreated bamboo sawdust (150 °C) was 4.12% lower. In this regard, microwave hydrothermal pretreatment is more suitable for upgrading the pyrolysis oil quality than conventional hydrothermal pretreatment.

Synthesis and Thermal and Photo Behaviors of New Polyamide/Organocaly Nanocomposites Containing Para Phenylenediacrylic Moiety

Science.gov (United States)

Faghihi, Khalil; Soleimani, Masoumeh; Shabanian, Meisam; Abootalebi, Ashraf Sadat

2011-06-01

New type of aromatic polyamide/montmorillonite nanocomposites were produced using solution process in N-methyl-2-pyrolidone. Amide chains were synthesized from 4,4'-diaminodiphenyl sulfone and p-phenylenediacrylic acid in N-methyl-2-pyrolidone. The resulting nanocomposite films containing 5-15 mass % of organoclay were characterized for FT-IR, scanning electronmicroscopy (SEM), X-ray diffraction (XRD), thermogravimetric analysis (TGA), optical transparency and water absorption measurements. The distribution of organoclay and nanostructure of the composites were investigated by (XRD) and SEM analyses. Thermogravimetric analysis indicated an increase in thermal stability of nanocomposites as compared to pristine polyamide. The percentage optical transparency and water absorption of these hybrids was found to be much reduced upon the addition of modified layered silicate indicating decreased permeability.

Intrinsic dependence of the magnetic properties of CoFe{sub 2}O{sub 4} nanoparticles prepared via chemical methods with addition of chelating agents

Energy Technology Data Exchange (ETDEWEB)

Mendonça, E.C. [Núcleo de Pós-Graduação em Física, Campus Prof. José Aluísio de Campos, UFS, 49100-000 São Cristóvão, SE (Brazil); Tenório, Mayara A. [Departamento de Física, Campus Prof. Alberto Carvalho, UFS, 49500-000 Itabaiana, SE (Brazil); Mecena, S.G.; Zucolotto, B.; Silva, L.S. [Núcleo de Pós-Graduação em Física, Campus Prof. José Aluísio de Campos, UFS, 49100-000 São Cristóvão, SE (Brazil); Jesus, C.B.R. [Instituto de Física Gleb Wataghin, UNICAMP, C. P. 6165, 13083-970 Campinas, SP (Brazil); Meneses, C.T. [Núcleo de Pós-Graduação em Física, Campus Prof. José Aluísio de Campos, UFS, 49100-000 São Cristóvão, SE (Brazil); and others

2015-12-01

In this work, the effect of addition of different chelating agents on the magnetic properties of cobalt ferrite nanoparticles produced by the combining of both co-precipitation and hydrothermal methods is reported. The Rietveld analyses of X-ray diffraction patterns reveal that our samples are single phase (space group: Fd-3m) with small average sizes. The weight losses observed in the thermogravimetric measurements together with the M×H curves show that the organic contamination coming from chelating agent decomposition can give rise to misinterpretation of the magnetization measurements. Besides, analyses of the zero-field-cooled (ZFC) and field-cooled (FC) magnetization measurements and the M×H curves measured at room temperature allows us to state that both the average blocking temperature and particles size distribution are sensitive to the kind of chelating agent. - Highlights: Superparamagnetism. Chelating agents. Organic contamination.

Analysing spatially extended high-dimensional dynamics by recurrence plots

Energy Technology Data Exchange (ETDEWEB)

Marwan, Norbert, E-mail: marwan@pik-potsdam.de [Potsdam Institute for Climate Impact Research, 14412 Potsdam (Germany); Kurths, Jürgen [Potsdam Institute for Climate Impact Research, 14412 Potsdam (Germany); Humboldt Universität zu Berlin, Institut für Physik (Germany); Nizhny Novgorod State University, Department of Control Theory, Nizhny Novgorod (Russian Federation); Foerster, Saskia [GFZ German Research Centre for Geosciences, Section 1.4 Remote Sensing, Telegrafenberg, 14473 Potsdam (Germany)

2015-05-08

Recurrence plot based measures of complexity are capable tools for characterizing complex dynamics. In this letter we show the potential of selected recurrence plot measures for the investigation of even high-dimensional dynamics. We apply this method on spatially extended chaos, such as derived from the Lorenz96 model and show that the recurrence plot based measures can qualitatively characterize typical dynamical properties such as chaotic or periodic dynamics. Moreover, we demonstrate its power by analysing satellite image time series of vegetation cover with contrasting dynamics as a spatially extended and potentially high-dimensional example from the real world. - Highlights: • We use recurrence plots for analysing partially extended dynamics. • We investigate the high-dimensional chaos of the Lorenz96 model. • The approach distinguishes different spatio-temporal dynamics. • We use the method for studying vegetation cover time series.

Kinetic stability analyses in a bumpy cylinder

International Nuclear Information System (INIS)

Dominguez, R.R.; Berk, H.L.

1981-01-01

Recent interest in the ELMO Bumpy Torus (EBT) has prompted a number of stability analyses of both the hot electron rings and the toroidal plasma. Typically these works employ the local approximation, neglecting radial eigenmode structure and ballooning effects to perform the stability analysis. In the present work we develop a fully kinetic formalism for performing nonlocal stability analyses in a bumpy cylinder. We show that the Vlasov-Maxwell integral equations (with one ignorable coordinate) are self-adjoint and hence amenable to analysis using numerical techniques developed for self-adjoint systems of equations. The representation we obtain for the kernel of the Vlasov-Maxwell equations is a differential operator of arbitrarily high order. This form leads to a manifestly self-adjoint system of differential equations for long wavelength modes

ALBEDO PATTERN RECOGNITION AND TIME-SERIES ANALYSES IN MALAYSIA

Directory of Open Access Journals (Sweden)

S. A. Salleh

2012-07-01

Full Text Available Pattern recognition and time-series analyses will enable one to evaluate and generate predictions of specific phenomena. The albedo pattern and time-series analyses are very much useful especially in relation to climate condition monitoring. This study is conducted to seek for Malaysia albedo pattern changes. The pattern recognition and changes will be useful for variety of environmental and climate monitoring researches such as carbon budgeting and aerosol mapping. The 10 years (2000–2009 MODIS satellite images were used for the analyses and interpretation. These images were being processed using ERDAS Imagine remote sensing software, ArcGIS 9.3, the 6S code for atmospherical calibration and several MODIS tools (MRT, HDF2GIS, Albedo tools. There are several methods for time-series analyses were explored, this paper demonstrates trends and seasonal time-series analyses using converted HDF format MODIS MCD43A3 albedo land product. The results revealed significance changes of albedo percentages over the past 10 years and the pattern with regards to Malaysia's nebulosity index (NI and aerosol optical depth (AOD. There is noticeable trend can be identified with regards to its maximum and minimum value of the albedo. The rise and fall of the line graph show a similar trend with regards to its daily observation. The different can be identified in term of the value or percentage of rises and falls of albedo. Thus, it can be concludes that the temporal behavior of land surface albedo in Malaysia have a uniform behaviours and effects with regards to the local monsoons. However, although the average albedo shows linear trend with nebulosity index, the pattern changes of albedo with respects to the nebulosity index indicates that there are external factors that implicates the albedo values, as the sky conditions and its diffusion plotted does not have uniform trend over the years, especially when the trend of 5 years interval is examined, 2000 shows high

Analyse Risk-Return Paradox: Evidence from Electricity Sector of Pakistan

OpenAIRE

Naqi Shah, Sadia; Qayyum, Abdul

2016-01-01

This study analyse risk return relationship of the electricity companies of Pakistan by using the log return series of these electricity companies. Financial time series data have the property of autoregressive heteroscedasticity so move towards the GARCH family test. As the study want to analyse the risk return relationship so, GARCH-M Model of Engel et al (1987) is used, who empirically found relationship between risk and return. Results show that risk return in case of Pakistan electricity...

Race, Gender, and Reseacher Positionality Analysed Through Memory Work

DEFF Research Database (Denmark)

Andreassen, Rikke; Myong, Lene

2017-01-01

Drawing upon feminist standpoint theory and memory work, the authors analyse racial privilege by investigating their own racialized and gendered subjectifications as academic researchers. By looking at their own experiences within academia, they show how authority and agency are contingent upon...

Comparative biochemical analyses of venous blood and peritoneal fluid from horses with colic using a portable analyser and an in-house analyser.

Science.gov (United States)

Saulez, M N; Cebra, C K; Dailey, M

2005-08-20

Fifty-six horses with colic were examined over a period of three months. The concentrations of glucose, lactate, sodium, potassium and chloride, and the pH of samples of blood and peritoneal fluid, were determined with a portable clinical analyser and with an in-house analyser and the results were compared. Compared with the in-house analyser, the portable analyser gave higher pH values for blood and peritoneal fluid with greater variability in the alkaline range, and lower pH values in the acidic range, lower concentrations of glucose in the range below 8.3 mmol/l, and lower concentrations of lactate in venous blood in the range below 5 mmol/l and in peritoneal fluid in the range below 2 mmol/l, with less variability. On average, the portable analyser underestimated the concentrations of lactate and glucose in peritoneal fluid in comparison with the in-house analyser. Its measurements of the concentrations of sodium and chloride in peritoneal fluid had a higher bias and were more variable than the measurements in venous blood, and its measurements of potassium in venous blood and peritoneal fluid had a smaller bias and less variability than the measurements made with the in-house analyser.

Network-derived inhomogeneity in monthly rainfall analyses over western Tasmania

International Nuclear Information System (INIS)

Fawcett, Robert; Trewin, Blair; Barnes-Keoghan, Ian

2010-01-01

Monthly rainfall in the wetter western half of Tasmania was relatively poorly observed in the early to middle parts of the 20th century, and this causes a marked inhomogeneity in the operational gridded monthly rainfall analyses generated by the Australian Bureau of Meteorology up until the end of 2009. These monthly rainfall analyses were generated for the period 1900 to 2009 in two forms; a national analysis at 0.25 0 latitude-longitude resolution, and a southeastern Australia regional analysis at 0.1 0 resolution. For any given month, they used all the monthly data from the standard Bureau rainfall gauge network available in the Australian Data Archive for Meteorology. Since this network has changed markedly since Federation (1901), there is obvious scope for network-derived inhomogeneities in the analyses. In this study, we show that the topography-resolving techniques of the new Australian Water Availability Project analyses, adopted as the official operational analyses from the start of 2010, substantially diminish those inhomogeneities, while using largely the same observation network. One result is an improved characterisation of recent rainfall declines across Tasmania. The new analyses are available at two resolutions, 0.25 0 and 0.05 0 .

LOD score exclusion analyses for candidate genes using random population samples.

Science.gov (United States)

Deng, H W; Li, J; Recker, R R

2001-05-01

While extensive analyses have been conducted to test for, no formal analyses have been conducted to test against, the importance of candidate genes with random population samples. We develop a LOD score approach for exclusion analyses of candidate genes with random population samples. Under this approach, specific genetic effects and inheritance models at candidate genes can be analysed and if a LOD score is < or = - 2.0, the locus can be excluded from having an effect larger than that specified. Computer simulations show that, with sample sizes often employed in association studies, this approach has high power to exclude a gene from having moderate genetic effects. In contrast to regular association analyses, population admixture will not affect the robustness of our analyses; in fact, it renders our analyses more conservative and thus any significant exclusion result is robust. Our exclusion analysis complements association analysis for candidate genes in random population samples and is parallel to the exclusion mapping analyses that may be conducted in linkage analyses with pedigrees or relative pairs. The usefulness of the approach is demonstrated by an application to test the importance of vitamin D receptor and estrogen receptor genes underlying the differential risk to osteoporotic fractures.

Diagnostic Comparison of Meteorological Analyses during the 2002 Antarctic Winter

Science.gov (United States)

Manney, Gloria L.; Allen, Douglas R.; Kruger, Kirstin; Naujokat, Barbara; Santee, Michelle L.; Sabutis, Joseph L.; Pawson, Steven; Swinbank, Richard; Randall, Cora E.; Simmons, Adrian J.;

Flash pyrolysis kinetics of pine wood

NARCIS (Netherlands)

Wagenaar, B.M.; Prins, W.; van Swaaij, Willibrordus Petrus Maria

1993-01-01

The kinetics of sawdust pyrolysis in the temperature range from 300 to 600 °C has been measured. A thermogravimetric analyser was applied for the temperature range from 300 to 450 °C while for measurements in the temperature range from 450 to 600 °C, an entrained flow reactor has been used. The

Elemental abundance and analyses with coadded DAO spectrograms

International Nuclear Information System (INIS)

Adelman, S.J.

1987-01-01

One can improve the quality of elemental abundance analyses by using higher signal-to-noise data than has been the practice at high resolution. The procedures developed at the Dominion Astrophysical Observatory to coadd high-dispersion coude spectrograms are used with a minimum of 10 6.5 A mm -1 IIa-O spectrograms of each of three field horizontal-branch (FHB)A stars to increase the signal-to-noise ratio of the photographic data over a considerable wavelength region. Fine analyses of the sharp-lined prototype FHB stars HD 109995 and 161817 show an internal consistency which justifies this effort. Their photospheric elemental abundances are similar to those of Population II globular cluster giants. (author)

Unconscious analyses of visual scenes based on feature conjunctions.

Science.gov (United States)

Tachibana, Ryosuke; Noguchi, Yasuki

2015-06-01

To efficiently process a cluttered scene, the visual system analyzes statistical properties or regularities of visual elements embedded in the scene. It is controversial, however, whether those scene analyses could also work for stimuli unconsciously perceived. Here we show that our brain performs the unconscious scene analyses not only using a single featural cue (e.g., orientation) but also based on conjunctions of multiple visual features (e.g., combinations of color and orientation information). Subjects foveally viewed a stimulus array (duration: 50 ms) where 4 types of bars (red-horizontal, red-vertical, green-horizontal, and green-vertical) were intermixed. Although a conscious perception of those bars was inhibited by a subsequent mask stimulus, the brain correctly analyzed the information about color, orientation, and color-orientation conjunctions of those invisible bars. The information of those features was then used for the unconscious configuration analysis (statistical processing) of the central bars, which induced a perceptual bias and illusory feature binding in visible stimuli at peripheral locations. While statistical analyses and feature binding are normally 2 key functions of the visual system to construct coherent percepts of visual scenes, our results show that a high-level analysis combining those 2 functions is correctly performed by unconscious computations in the brain. (c) 2015 APA, all rights reserved).

Utilization of Large Scale Surface Models for Detailed Visibility Analyses

Science.gov (United States)

Caha, J.; Kačmařík, M.

2017-11-01

This article demonstrates utilization of large scale surface models with small spatial resolution and high accuracy, acquired from Unmanned Aerial Vehicle scanning, for visibility analyses. The importance of large scale data for visibility analyses on the local scale, where the detail of the surface model is the most defining factor, is described. The focus is not only the classic Boolean visibility, that is usually determined within GIS, but also on so called extended viewsheds that aims to provide more information about visibility. The case study with examples of visibility analyses was performed on river Opava, near the Ostrava city (Czech Republic). The multiple Boolean viewshed analysis and global horizon viewshed were calculated to determine most prominent features and visibility barriers of the surface. Besides that, the extended viewshed showing angle difference above the local horizon, which describes angular height of the target area above the barrier, is shown. The case study proved that large scale models are appropriate data source for visibility analyses on local level. The discussion summarizes possible future applications and further development directions of visibility analyses.

Target gene analyses of 39 amelogenesis imperfecta kindreds

Science.gov (United States)

Chan, Hui-Chen; Estrella, Ninna M. R. P.; Milkovich, Rachel N.; Kim, Jung-Wook; Simmer, James P.; Hu, Jan C-C.

2012-01-01

Previously, mutational analyses identified six disease-causing mutations in 24 amelogenesis imperfecta (AI) kindreds. We have since expanded the number of AI kindreds to 39, and performed mutation analyses covering the coding exons and adjoining intron sequences for the six proven AI candidate genes [amelogenin (AMELX), enamelin (ENAM), family with sequence similarity 83, member H (FAM83H), WD repeat containing domain 72 (WDR72), enamelysin (MMP20), and kallikrein-related peptidase 4 (KLK4)] and for ameloblastin (AMBN) (a suspected candidate gene). All four of the X-linked AI families (100%) had disease-causing mutations in AMELX, suggesting that AMELX is the only gene involved in the aetiology of X-linked AI. Eighteen families showed an autosomal-dominant pattern of inheritance. Disease-causing mutations were identified in 12 (67%): eight in FAM83H, and four in ENAM. No FAM83H coding-region or splice-junction mutations were identified in three probands with autosomal-dominant hypocalcification AI (ADHCAI), suggesting that a second gene may contribute to the aetiology of ADHCAI. Six families showed an autosomal-recessive pattern of inheritance, and disease-causing mutations were identified in three (50%): two in MMP20, and one in WDR72. No disease-causing mutations were found in 11 families with only one affected member. We conclude that mutation analyses of the current candidate genes for AI have about a 50% chance of identifying the disease-causing mutation in a given kindred. PMID:22243262

Show-Bix &

DEFF Research Database (Denmark)

2014-01-01

The anti-reenactment 'Show-Bix &' consists of 5 dias projectors, a dial phone, quintophonic sound, and interactive elements. A responsive interface will enable the Dias projectors to show copies of original dias slides from the Show-Bix piece ”March på Stedet”, 265 images in total. The copies are...

VESPA: Very large-scale Evolutionary and Selective Pressure Analyses

Directory of Open Access Journals (Sweden)

Andrew E. Webb

2017-06-01

Full Text Available Background Large-scale molecular evolutionary analyses of protein coding sequences requires a number of preparatory inter-related steps from finding gene families, to generating alignments and phylogenetic trees and assessing selective pressure variation. Each phase of these analyses can represent significant challenges, particularly when working with entire proteomes (all protein coding sequences in a genome from a large number of species. Methods We present VESPA, software capable of automating a selective pressure analysis using codeML in addition to the preparatory analyses and summary statistics. VESPA is written in python and Perl and is designed to run within a UNIX environment. Results We have benchmarked VESPA and our results show that the method is consistent, performs well on both large scale and smaller scale datasets, and produces results in line with previously published datasets. Discussion Large-scale gene family identification, sequence alignment, and phylogeny reconstruction are all important aspects of large-scale molecular evolutionary analyses. VESPA provides flexible software for simplifying these processes along with downstream selective pressure variation analyses. The software automatically interprets results from codeML and produces simplified summary files to assist the user in better understanding the results. VESPA may be found at the following website: http://www.mol-evol.org/VESPA.

Steady-state and accident analyses of PBMR with the computer code SPECTRA

International Nuclear Information System (INIS)

Stempniewicz, Marek M.

2002-01-01

The SPECTRA code is an accident analysis code developed at NRG. It is designed for thermal-hydraulic analyses of nuclear or conventional power plants. The code is capable of analysing the whole power plant, including reactor vessel, primary system, various control and safety systems, containment and reactor building. The aim of the work presented in this paper was to prepare a preliminary thermal-hydraulic model of PBMR for SPECTRA, and perform steady state and accident analyses. In order to assess SPECTRA capability to model the PBMR reactors, a model of the INCOGEN system has been prepared first. Steady state and accident scenarios were analyzed for INCOGEN configuration. Results were compared to the results obtained earlier with INAS and OCTOPUS/PANTHERMIX. A good agreement was obtained. Results of accident analyses with PBMR model showed qualitatively good results. It is concluded that SPECTRA is a suitable tool for analyzing High Temperature Reactors, such as INCOGEN or for example PBMR (Pebble Bed Modular Reactor). Analyses of INCOGEN and PBMR systems showed that in all analyzed cases the fuel temperatures remained within the acceptable limits. Consequently there is no danger of release of radioactivity to the environment. It may be concluded that those are promising designs for future safe industrial reactors. (author)

Children with dyslexia show cortical hyperactivation in response to increasing literacy processing demands

Directory of Open Access Journals (Sweden)

Frøydis eMorken

2014-12-01

Full Text Available This fMRI study aimed to examine how differences in literacy processing demands may affect cortical activation patterns in 11- to 12-year-old children with dyslexia as compared to children with typical reading skills. 11 children with and 18 without dyslexia were assessed using a reading paradigm based on different stages of literacy development. In the analyses, six regions showed an interaction effect between group and condition in a factorial ANOVA. These regions were selected as regions of interest for further analyses. Overall, the dyslexia group showed cortical hyperactivation compared to the typical group. The difference between the groups tended to increase with increasing processing demands. Differences in cortical activation were not reflected in in-scanner reading performance. The six regions further grouped into three patterns, which are discussed in terms of processing demands, compensatory mechanisms, orthography and contextual facilitation. We conclude that the observed hyperactivation is chiefly a result of compensatory activity, modulated by other factors.

Study of oxidation behaviour of Zr-based bulk amorphous alloy Zr 65 ...

Indian Academy of Sciences (India)

The oxidation behaviour of Zr-based bulk amorphous alloy Zr65Cu17.5Ni10Al7.5 has been studied in air environment at various temperatures in the temperature range 591–684 K using a thermogravimetric analyser (TGA). The oxidation kinetics of the alloy in the amorphous phase obeys the parabolic rate law for oxidation ...

Integrative analyses of leprosy susceptibility genes indicate a common autoimmune profile.

Science.gov (United States)

Zhang, Deng-Feng; Wang, Dong; Li, Yu-Ye; Yao, Yong-Gang

2016-04-01

Leprosy is an ancient chronic infection in the skin and peripheral nerves caused by Mycobacterium leprae. The development of leprosy depends on genetic background and the immune status of the host. However, there is no systematic view focusing on the biological pathways, interaction networks and overall expression pattern of leprosy-related immune and genetic factors. To identify the hub genes in the center of leprosy genetic network and to provide an insight into immune and genetic factors contributing to leprosy. We retrieved all reported leprosy-related genes and performed integrative analyses covering gene expression profiling, pathway analysis, protein-protein interaction network, and evolutionary analyses. A list of 123 differentially expressed leprosy related genes, which were enriched in activation and regulation of immune response, was obtained in our analyses. Cross-disorder analysis showed that the list of leprosy susceptibility genes was largely shared by typical autoimmune diseases such as lupus erythematosus and arthritis, suggesting that similar pathways might be affected in leprosy and autoimmune diseases. Protein-protein interaction (PPI) and positive selection analyses revealed a co-evolution network of leprosy risk genes. Our analyses showed that leprosy associated genes constituted a co-evolution network and might undergo positive selection driven by M. leprae. We suggested that leprosy may be a kind of autoimmune disease and the development of leprosy is a matter of defect or over-activation of body immunity. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Final report for tank 241-AP-108, grab samples 8AP-96-1, 8AP-96-2 and 8AP-96-FB

International Nuclear Information System (INIS)

Esch, R.A.

1996-01-01

This document is the final report deliverable for the tank 241-AP-108 grab samples. The samples were subsampled and analyzed in accordance with the TSAP. Included in this report are the results for the Waste Compatibility analyses, with the exception of DSC and thermogravimetric analysis (TGA) results which were presented in the 45 Day report (Part 2 of this document). The raw data for all analyses, with the exception of DSC and TGA, are also included in this report

Thermogravimetric study on the hydration of reactive magnesia and silica mixture at room temperature

International Nuclear Information System (INIS)

Jin, Fei; Al-Tabbaa, Abir

2013-01-01

Highlights: • The characteristics of reactive MgO vary significantly in terms of their impurity content and reactivity depending on their sources and calcination conditions. • The synthesis of magnesium silicate hydrate (MSH) is affected by the characteristics of the precursors, i.e., MgO and silica. • The reaction process in the MgO–SiO 2 –H 2 O system can be followed by TGA, and is essential to develop MSH-based materials. - Abstract: The synthesis of magnesium silicate hydrate (MSH), which has wide applications in both construction and environmental fields, has been studied for decades. However, it is known that the characteristics of magnesia (MgO) vary significantly depending on their calcination conditions, which is expected to affect their performance in the MgO–SiO 2 –H 2 O system. This paper investigated the effect of different MgO and silica sources on the formation of magnesium silicate hydrate (MSH) at room temperature. The hydration process was studied by mixing commercial reactive MgO and silica powders with water and curing for 1, 7 and 28 days. The hydration products were analysed with the help of X-ray diffraction (XRD) and thermogravimatric analysis (TGA). The results showed the continuous consumption of MgO and the existence of MSH and brucite and other minor phases such as magnesite and calcite. It is found that the Mg and Si sources have significant effect on the hydration process of MgO–SiO 2 –H 2 O system. The reaction degree is controlled by the availability of dissolved Mg and Si in the solution. The former is determined by the reactivity of MgO and the latter is related to the reactivity of the silica as well as the pH of the system

Grey literature in meta-analyses of randomized trials of health care interventions.

Science.gov (United States)

Hopewell, S; McDonald, S; Clarke, M; Egger, M

2007-04-18

The inclusion of grey literature (i.e. literature that has not been formally published) in systematic reviews may help to overcome some of the problems of publication bias, which can arise due to the selective availability of data. To review systematically research studies, which have investigated the impact of grey literature in meta-analyses of randomized trials of health care interventions. We searched the Cochrane Methodology Register (The Cochrane Library Issue 3, 2005), MEDLINE (1966 to 20 May 2005), the Science Citation Index (June 2005) and contacted researchers who may have carried out relevant studies. A study was considered eligible for this review if it compared the effect of the inclusion and exclusion of grey literature on the results of a cohort of meta-analyses of randomized trials. Data were extracted from each report independently by two reviewers. The main outcome measure was an estimate of the impact of trials from the grey literature on the pooled effect estimates of the meta-analyses. Information was also collected on the area of health care, the number of meta-analyses, the number of trials, the number of trial participants, the year of publication of the trials, the language and country of publication of the trials, the number and type of grey and published literature, and methodological quality. Five studies met the inclusion criteria. All five studies showed that published trials showed an overall greater treatment effect than grey trials. This difference was statistically significant in one of the five studies. Data could be combined for three of the five studies. This showed that, on average, published trials showed a 9% greater treatment effect than grey trials (ratio of odds ratios for grey versus published trials 1.09; 95% CI 1.03-1.16). Overall there were more published trials included in the meta-analyses than grey trials (median 224 (IQR 108-365) versus 45(IQR 40-102)). Published trials had more participants on average. The most

Mineralogy of the Tertiary Clay Deposits in Makkah and Rabigh Quadrangles, West Central Arabian Shield, Saudi Arabia

Directory of Open Access Journals (Sweden)

M.H. Basyoni

2002-06-01

Full Text Available The mineralogy of the Tertiary clay deposits in Makkah and Rabigh quadrangles was thoroughly investigated by X-ray diffraction and differential thermal and thermogravimetric analyses in addition to other techniques. Results show that the investigated samples are predominantly composed of montmorillonite (Ca++ and/or Mg++ rich variety and kaolinite, associated with subordinate illite and minor chlorite. Mixed layer montmorillonite-illite is recorded only in two samples. The relative abundance of these minerals by X-ray diffraction analysis showed that the studied clay deposits are of three types. The first, which is the most common, is highly montmorillonitic, the second is made up of a mixture of montmorillonite followed by kaolinite and illite and the third is highly kaolinitic with some montmorillonite. Generally, kaolinite shows a southward increase in Makkah quadrangle while chlorite, as a minor component, shows a northward increase in Rabigh quadrangle.

Thermal analysis of physical and chemical changes occuring during regeneration of activated carbon

Directory of Open Access Journals (Sweden)

Radić Dejan B.

2017-01-01

Full Text Available High-temperature thermal process is a commercial way of regeneration of spent granular activated carbon. The paper presents results of thermal analysis conducted in order to examine high-temperature regeneration of spent activated carbon, produced from coconut shells, previously used in drinking water treatment. Results of performed thermogravimetric analysis, derivative thermogravimetric analysis, and differential thermal analysis, enabled a number of hypotheses to be made about different phases of activated carbon regeneration, values of characteristic parameters during particular process phases, as well as catalytic impact of inorganic materials on development of regeneration process. Samples of activated carbon were heated up to 1000°C in thermogravimetric analyser while maintaining adequate oxidizing or reducing conditions. Based on diagrams of thermal analysis for samples of spent activated carbon, temperature intervals of the first intense mass change phase (180-215°C, maximum of exothermic processes (400-450°C, beginning of the second intense mass change phase (635-700°C, and maximum endothermic processes (800-815°C were deter-mined. Analysing and comparing the diagrams of thermal analysis for new, previously regenerated and spent activated carbon, hypothesis about physical and chemical transformations of organic and inorganic adsorbate in spent activated carbon are given. Transformation of an organic adsorbate in the pores of activated carbon, results in loss of mass and an exothermic reaction with oxygen in the vapour phase. The reactions of inorganic adsorbate also result the loss of mass of activated carbon during its heating and endothermic reactions of their degradation at high temperatures.

Energy and exergy analyses of an integrated solar heat pump system

International Nuclear Information System (INIS)

Suleman, F.; Dincer, I.; Agelin-Chaab, M.

2014-01-01

An integrated solar and heat pump based system for industrial heating is developed in this study. The system comprises heat pump cycle for process heating water and solar energy for another industrial heating process. Comprehensive energy and exergy analyses are performed on the system. These analyses generated some compelling results as expected because of the use of green and environmentally friendly energy sources. The results show that the energy efficiency of the process is 58% while the exergy efficiency is 75%. Energetic COP of the heat pump cycle is 3.54 whereas the exergy efficiency is 42.5%. Moreover, the energetic COP of the system is 2.97 and the exergy efficiency of the system is 35.7%. In the parametric study, a different variation such as changing the temperature and pressure of the condenser also shows positive results. - Highlights: • An integrated system is analysed using renewable energy source which can be used in textile industry. • Energy losses and exergy destructions are calculated at all major components. • Energy and exergy efficiencies of all subunits, subsystems and overall system are determined. • A parametric study shows the effect of environment and operating conditions on efficiencies. • Solar energy for heating in textile industry is efficient and environmentally friendly

Modification of a cellulose derived for your application on enzyme immobilization

International Nuclear Information System (INIS)

Carvalho, Elaine S.; Rodriguez, Ruben J.S.; Lamonica, Alano C.; Tavares, Maria Ines B.

2009-01-01

The chemical modification of (acrylamidomethyl) cellulose acetate propionate (AMCAP) was done through the technique of grafting via radical using acrylic acid as modifier, with the objective to make the polymer more hydrophilic. The structural characterization of AMCAP and modified AMCAP-H 2 O 2 was analysed by using the technique of 13 C-nuclear magnetic resonance (NMR- 13 C). By the techniques differential scanning calorimetry analysis (DSC) and thermogravimetric analysis (TGA), the thermal properties was characterized and the hydrophobic / hydrophilic character was determined by measurements of the contact angle. The results show that occurred the change intended with the introduction of acrylic acid in the side chain of the polymer, increasing the hydrophilic character on the AMCAP. (author)

Towards understanding the thermoanalysis of water sorption on lithium orthosilicate (Li{sub 4}SiO{sub 4})

Energy Technology Data Exchange (ETDEWEB)

Ortiz-Landeros, J. [Instituto de Investigaciones en Materiales, Universidad Nacional Autonoma de Mexico, Circuito exterior s/n, Ciudad Universitaria, CP 04510, Del. Coyoacan, Mexico DF (Mexico); Departamento de Ingenieria en Metalurgia y Materiales, ESIQIE, Instituto Politecnico Nacional, UPALM, Av. Instituto Politecnico Nacional s/n, CP 07738, Mexico DF (Mexico); Martinez-dlCruz, L. [Instituto de Investigaciones en Materiales, Universidad Nacional Autonoma de Mexico, Circuito exterior s/n, Ciudad Universitaria, CP 04510, Del. Coyoacan, Mexico DF (Mexico); Gomez-Yanez, C. [Departamento de Ingenieria en Metalurgia y Materiales, ESIQIE, Instituto Politecnico Nacional, UPALM, Av. Instituto Politecnico Nacional s/n, CP 07738, Mexico DF (Mexico); Pfeiffer, H., E-mail: pfeiffer@iim.unam.mx [Instituto de Investigaciones en Materiales, Universidad Nacional Autonoma de Mexico, Circuito exterior s/n, Ciudad Universitaria, CP 04510, Del. Coyoacan, Mexico DF (Mexico)

2011-03-10

A systematic thermogravimetric study of hygroscopic and reactivity behaviors, at low temperatures of lithium orthosilicate (Li{sub 4}SiO{sub 4}), are presented. Li{sub 4}SiO{sub 4} sample was prepared by solid-state reaction and then treated at different temperature-humidity conditions. Li{sub 4}SiO{sub 4} samples previously treated under different temperature-humidity conditions were characterized by Fourier transform infrared spectroscopy and thermogravimetric analyses. Different processes, adsorption and absorption, take place between the Li{sub 4}SiO{sub 4} and water vapor. Absorbed water produces superficial hydroxylated species such as Si-OH and Li-OH. In addition, a kinetic analysis was performed, and the different water absorption activation enthalpies were calculated. It was found that activation enthalpy ({Delta}H) values decrease when the relative humidity is incremented, from 5528.6 J/mol to 2074.2 J/mol at relative humidity levels of 60% and 75% respectively. These results show the impact of different humidity and temperature conditions on the stability and/or chemical reactivity of Li{sub 4}SiO{sub 4}, if this ceramic is used in different application fields, such as carbon dioxide captor or as a breeder ceramic into the fusion reactors.

Characterization of metal-bound water in bioactive Fe(III)-cyclophane complexes

Science.gov (United States)

Salazar-Medina, A. J.; Gámez-Corrales, R.; Ramírez, J. Z.; González-Aguilar, G. A.; Velázquez-Contreras, E. F.

2018-02-01

Binuclear Fe(III) complexes, Fe2PO and Fe2PC, have functions of antioxidants as well as superoxide dismutase and peroxidase mimickers. The role of water molecules in the non-cytotoxic properties of these complexes have been studied by thermogravimetric and IR/Raman-spectroscopic methods. The thermogravimetric analysis of Fe2PO shows the presence of nine water molecules (Fe2PO·9H2O), three of which are directly coordinated to the metallic ion; the remaining six molecules occupy the secondary coordination sphere. For Fe2PC, eight water molecules were detected (Fe2PC·8H2O), and only one of them directly coordinates to the metallic ion. IR/Raman spectrum analyses corroborate the presence of water molecules in both metallic complexes and the mode of coordination to the ligand, on the basis of bands characteristic of hydration water at ∼3300 cm-1 and bands of adsorbed water between 430 and 490 cm-1. A pentacoordinate geometry is proposed for Fe2PO and a hexacoordinated geometry for Fe2PC. Those results are consistent with theoretical calculations performed through a semiempirical PM7 method. The presence of coordinated water molecules is closely related to the reactivity of Fe2PO and Fe2PC in solution.

Synthesis, characterization and field evaluation of a new calcium-based CO2 absorbent for radial diffusive sampler

Science.gov (United States)

Cucciniello, Raffaele; Proto, Antonio; Alfano, Davide; Motta, Oriana

2012-12-01

In this paper the use of passive sampling as a powerful approach to monitor atmospheric CO2 is assessed. Suitable substrate based on calcium-aluminium oxide was synthetized according to a process which permits to control the particle size of the CaO/Al based sorbent. The study shows that hydration of substrate is an essential part of the process of CO2 absorption and subsequent conversion to carbonate. X-ray diffraction, thermogravimetric analysis, environmental scanning electron microscopic analysis were used in order to characterize the substrate and to establish the best performances both in terms of particle size and CO2 absorption capacity. Passive samplers for CO2 monitoring were prepared and then tested at laboratory level and in the atmospheric environment. Validation was performed by comparison with an infrared continuous detector. Thermogravimetric analysis results, carried out to evaluate the absorbing capability of this new passive device, were in accordance with data collected at the same time by the active continuous analyser. The diffusive sampling rate and the diffusion coefficient of CO2 respect to this new passive device were also evaluated resulting equal to 47 ± 3 ml min-1 and 0.0509 ± 0.005 cm2 s-1, respectively.

Review of radionuclide source terms used for performance-assessment analyses

International Nuclear Information System (INIS)

Barnard, R.W.

1993-06-01

Two aspects of the radionuclide source terms used for total-system performance assessment (TSPA) analyses have been reviewed. First, a detailed radionuclide inventory (i.e., one in which the reactor type, decay, and burnup are specified) is compared with the standard source-term inventory used in prior analyses. The latter assumes a fixed ratio of pressurized-water reactor (PWR) to boiling-water reactor (BWR) spent fuel, at specific amounts of burnup and at 10-year decay. TSPA analyses have been used to compare the simplified source term with the detailed one. The TSPA-91 analyses did not show a significant difference between the source terms. Second, the radionuclides used in source terms for TSPA aqueous-transport analyses have been reviewed to select ones that are representative of the entire inventory. It is recommended that two actinide decay chains be included (the 4n+2 ''uranium'' and 4n+3 ''actinium'' decay series), since these include several radionuclides that have potentially important release and dose characteristics. In addition, several fission products are recommended for the same reason. The choice of radionuclides should be influenced by other parameter assumptions, such as the solubility and retardation of the radionuclides

Hanseniaspora uvarum from winemaking environments show spatial and temporal genetic clustering

Directory of Open Access Journals (Sweden)

Warren eAlbertin

2016-01-01

Full Text Available Hanseniaspora uvarum is one of the most abundant yeast species found on grapes and in grape must, at least before the onset of alcoholic fermentation which is usually performed by Saccharomyces species. The aim of this study was to characterise the genetic and phenotypic variability within the H. uvarum species. One hundred and fifteen strains isolated from winemaking environments in different geographical origins were analysed using 11 microsatellite markers and a subset of 47 strains were analysed by AFLP. H. uvarum isolates clustered mainly on the basis of their geographical localisation as revealed by microsatellites. In addition, a strong clustering based on year of isolation was evidenced, indicating that the genetic diversity of Hanseniaspora uvarum isolates was related to both spatial and temporal variations. Conversely, clustering analysis based on AFLP data provided a different picture with groups showing no particular characteristics, but provided higher strain discrimination. This result indicated that AFLP approaches are inadequate to establish the genetic relationship between individuals, but allowed good strain discrimination. At the phenotypic level, several extracellular enzymatic activities of enological relevance (pectinase, chitinase, protease, β-glucosidase were measured but showed low diversity. The impact of environmental factors of enological interest (temperature, anaerobia and copper addition on growth was also assessed and showed poor variation. Altogether, this work provided both new analytical tool (microsatellites and new insights into the genetic and phenotypic diversity of H. uvarum, a yeast species that has previously been identified as a potential candidate for co-inoculation in grape must, but whose intraspecific variability had never been fully assessed.

Men and women show similar survival outcome in stage IV breast cancer.

Science.gov (United States)

Wu, San-Gang; Zhang, Wen-Wen; Liao, Xu-Lin; Sun, Jia-Yuan; Li, Feng-Yan; Su, Jing-Jun; He, Zhen-Yu

2017-08-01

To evaluate the clinicopathological features, patterns of distant metastases, and survival outcome between stage IV male breast cancer (MBC) and female breast cancer (FBC). Patients diagnosed with stage IV MBC and FBC between 2010 and 2013 were included using the Surveillance, Epidemiology, and End Results program. Univariate and multivariate Cox regression analyses were used to analyze risk factors for overall survival (OS). A total of 4997 patients were identified, including 60 MBC and 4937 FBC. Compared with FBC, patients with MBC were associated with a significantly higher rate of estrogen receptor-positive, progesterone receptor-positive, unmarried, lung metastases, and a lower frequency of liver metastases. Univariate and multivariate analyses showed no significant difference in OS between MBC and FBC. In the propensity score-matched population, there was also no difference in survival between MBC and FBC. Multivariate analysis of MBC showed that OS was longer for patients aged 50-69 years and with estrogen receptor-positive disease. There was no significant difference in survival outcome between stage IV MBC and FBC, but significant differences in clinicopathological features and patterns of metastases between the genders. Copyright © 2017 Elsevier Ltd. All rights reserved.

Fungal communities in wheat grain show significant co-existence patterns among species

DEFF Research Database (Denmark)

Nicolaisen, M.; Justesen, A. F.; Knorr, K.

2014-01-01

identified as ‘core’ OTUs as they were found in all or almost all samples and accounted for almost 99 % of all sequences. The remaining OTUs were only sporadically found and only in small amounts. Cluster and factor analyses showed patterns of co-existence among the core species. Cluster analysis grouped...... the 21 core OTUs into three clusters: cluster 1 consisting of saprotrophs, cluster 2 consisting mainly of yeasts and saprotrophs and cluster 3 consisting of wheat pathogens. Principal component extraction showed that the Fusarium graminearum group was inversely related to OTUs of clusters 1 and 2....

Radiation physics and shielding codes and analyses applied to design-assist and safety analyses of CANDUR and ACRTM reactors

International Nuclear Information System (INIS)

Aydogdu, K.; Boss, C. R.

2006-01-01

This paper discusses the radiation physics and shielding codes and analyses applied in the design of CANDU and ACR reactors. The focus is on the types of analyses undertaken rather than the inputs supplied to the engineering disciplines. Nevertheless, the discussion does show how these analyses contribute to the engineering design. Analyses in radiation physics and shielding can be categorized as either design-assist or safety and licensing (accident) analyses. Many of the analyses undertaken are designated 'design-assist' where the analyses are used to generate recommendations that directly influence plant design. These recommendations are directed at mitigating or reducing the radiation hazard of the nuclear power plant with engineered systems and components. Thus the analyses serve a primary safety function by ensuring the plant can be operated with acceptable radiation hazards to the workers and public. In addition to this role of design assist, radiation physics and shielding codes are also deployed in safety and licensing assessments of the consequences of radioactive releases of gaseous and liquid effluents during normal operation and gaseous effluents following accidents. In the latter category, the final consequences of accident sequences, expressed in terms of radiation dose to members of the public, and inputs to accident analysis, e.g., decay heat in fuel following a loss-of-coolant accident, are also calculated. Another role of the analyses is to demonstrate that the design of the plant satisfies the principle of ALARA (as low as reasonably achievable) radiation doses. This principle is applied throughout the design process to minimize worker and public doses. The principle of ALARA is an inherent part of all design-assist recommendations and safety and licensing assessments. The main focus of an ALARA exercise at the design stage is to minimize the radiation hazards at the source. This exploits material selection and impurity specifications and relies

Radiocarbon analyses along the EDML ice core in Antarctica

NARCIS (Netherlands)

van de Wal, R.S.W.; Meijer, H.A.J.; van Rooij, M.; van der Veen, C.

2007-01-01

Samples, 17 in total, from the EDML core drilled at Kohnen station Antarctica are analysed for 14CO and 14CO2 with a dry-extraction technique in combination with accelerator mass spectrometry. Results of the in situ produced 14CO fraction show a very low concentration of in situ produced 14CO.

Radiocarbon analyses along the EDML ice core in Antarctica

NARCIS (Netherlands)

Van de Wal, R. S. W.; Meijer, H. A. J.; De Rooij, M.; Van der Veen, C.

Samples, 17 in total, from the EDML core drilled at Kohnen station Antarctica are analysed for (CO)-C-14 and (CO2)-C-14 with a dry-extraction technique in combination with accelerator mass spectrometry. Results of the in situ produced (CO)-C-14 fraction show a very low concentration of in situ

45-Day safety screen results for tank 241-U-202, push mode, cores 75 and 78

International Nuclear Information System (INIS)

Jo, J.

1995-01-01

This document is a report of the analytical results for samples collected from the radioactive wastes in Tank 241-U-202 at the Hanford Reservation. Core samples were collected from the solid wastes in the tank and underwent safety screening analyses including differential scanning calorimetry, thermogravimetric analysis, and total alpha analysis. Results indicate that no safety screening notification limits were exceeded

Synthesis and Structural Studies of Nanocrystalline Cd 0.3 Zn 0.7 Fe ...

African Journals Online (AJOL)

The precursor was characterized by hydrazine and metal analyses, infrared spectral analysis and thermogravimetric analysis. Under appropriate annealing conditions, Cd0.3Zn0.7Fe2(cin)3(N2H4)2 yielded Cd0.3Zn0.7Fe2O4 nanoparticles, which were characterized for their size and structure using X-Ray Diffraction (XRD), ...

Dynamics of energy systems: Methods of analysing technology change

Energy Technology Data Exchange (ETDEWEB)

Neij, Lena

1999-05-01

Technology change will have a central role in achieving a sustainable energy system. This calls for methods of analysing the dynamics of energy systems in view of technology change and policy instruments for effecting and accelerating technology change. In this thesis, such methods have been developed, applied, and assessed. Two types of methods have been considered, methods of analysing and projecting the dynamics of future technology change and methods of evaluating policy instruments effecting technology change, i.e. market transformation programmes. Two methods are focused on analysing the dynamics of future technology change; vintage models and experience curves. Vintage models, which allow for complex analysis of annual streams of energy and technological investments, are applied to the analysis of the time dynamics of electricity demand for lighting and air-distribution in Sweden. The results of the analyses show that the Swedish electricity demand for these purposes could decrease over time, relative to a reference scenario, if policy instruments are used. Experience curves are used to provide insight into the prospects of diffusion of wind turbines and photo voltaic (PV) modules due to cost reduction. The results show potential for considerable cost reduction for wind-generated electricity, which, in turn, could lead to major diffusion of wind turbines. The results also show that major diffusion of PV modules, and a reduction of PV generated electricity down to the level of conventional base-load electricity, will depend on large investments in bringing the costs down (through R D and D, market incentives and investments in niche markets) or the introduction of new generations of PV modules (e.g. high-efficiency mass-produced thin-film cells). Moreover, a model has been developed for the evaluation of market transformation programmes, i.e. policy instruments that effect technology change and the introduction and commercialisation of energy

Design and manufacture of TL analyser by using the microcomputer

International Nuclear Information System (INIS)

Doh, Sih Hong; Woo, Chong Ho

1986-01-01

This paper describes the design of the thermoluminescence analyser using microcomputer. TL analyser is designed to perform the three step heat treatment, such as pre-read heating, readout procedure and post-heating (or pre-irradiation ) anneal. We used a 12-bit A/D converter to get the precise measurement and the phase control method to control the heating temperature. Since the used Apple II microcomputer is cheap and popular, it is possible to design the economical system. Experimental results showed the successful operation with flexibility. The error of temperature control was less than ± 0.2% of the expected value. (Author)

Thermogravimetric analysis of multi-stage hydropyrolysis of different coals

Energy Technology Data Exchange (ETDEWEB)

Li, W.; Wang, N.; Li, B [Chinese Academy of Sciences, Taiyuan (China). State Key Lab. of Coal Conversion

2001-09-01

Based on the characteristic of hydropyrolysis (HyPy), a multi-stage MHyPy of different coals was investigated using thermogravimetry. The results show that keeping the near peak temperature for some time in HyPy process can obviously increase the conversion rate, which is believed due to the full match between formation rate of free radicals and supply of hydrogen. The fast heating in MHyPy process results in the same conversion rate as that of the slow heating in HyPy process, which leads to the less reaction time and high yield of oil. The effect of MHyPy depends on the coal structure itself and it is notable for the coal with high H/C ratio. This suggests that the external hydrogen promotes the reaction between intrinsic hydrogen and free radicals. The MHyPy improves the removal of sulfur and nitrogen. 5 refs., 7 figs., 2 tabs.

Synthesis and Characterization of Magnesium Substituted Aluminophosphate Molecular Sieves with AEL Structure

Institute of Scientific and Technical Information of China (English)

Benjing Xu; Ling Qian; Xinmei Liu; Chunmin Song; Zifeng Yan

2004-01-01

MAPO-11 molecular sieves were synthesized by hydrothermal methods. The influence of precursor of magnesium, Mg/Al ratio, synthesis temperature, synthesis time and the type of template on the formation and properties of MAPO-11 molecular sieves was examined. The samples were characterized by the techniques of X-ray diffraction (XRD), scanning electron microscopy (SEM), thermogravimetric/differential thermogravimetric analysis (TG-DGA), etc. The results show that the shape and size of crystal were influenced by the precursor of Mg, the Mg/Al ratio and the type of template, and the TG-DGA analysis shows that MAPO-11 molecular sieves as-synthesized have poor thermal stability.

International trade shows: Structure, strategy and performance of exhibitors at individual booths vs. joint booths

DEFF Research Database (Denmark)

Hansen, Kåre

2000-01-01

This paper examines differences in exhibitors who participate at international trade shows at joint booths and those who participate at individual booths. The structure, strategy, and trade show performance of exhibitors at joint booths and those at individual booths are analysed. The analysis...... implications for exhibitors at interna-tional trade shows and export marketing programmes and other marketing programmes offering services to international trade show exhibitors....... of exhibitors at the international food shows SIAL (Paris) and ANUGA (Cologne) showed several significant differences with regard to structure and strategy. However, no significant differences in the performance assessments between the two partici-pation modes were found. The findings have important...

Physico-Chemical Characterizations of Sawdust-Derived Bio char as Potential Solid Fuels

International Nuclear Information System (INIS)

Wan Azlina Wan Ab Karim Ghani

2014-01-01

Characterization Malaysian rubber-wood sawdust derived bio char (MRWSB) produced in the fixed bed pyrolysis under different temperatures (450 to 850 degree Celsius) were studied for its applicability as a solid fuel. A range of analyses were carried out, including bio char oxidation reactivity , inorganic species, oxygen and hydrogen contents in the bio chars, release of heteroatoms in bio char as the gaseous product, and bio char structural evolution during pyrolysis process. The results show that the optimum temperature for carbonization to obtain a char having moderately high yield was found as 450 degree Celsius. Thermogravimetric analyses (TG) shows that temperatures induces a progressively more ordered carbonaceous structure and leads to a significant changes in the bio char reactivity. The process is coupled with the loss of heteroatoms, released as dominantly carbon dioxide (C0 2 ) and carbon dioxide (CO). In addition, the elemental study of wood-derived bio char shows the higher carbon content but with low H/C and 0/C ratio suggested this material was dominated by highly aromatic structures and this were revealed in the Fourier transform infra-red (FTIR). More importantly, insignificant amount of inorganic species is evidenced in the samples. (author)

Analysing Protocol Stacks for Services

DEFF Research Database (Denmark)

Gao, Han; Nielson, Flemming; Nielson, Hanne Riis

2011-01-01

We show an approach, CaPiTo, to model service-oriented applications using process algebras such that, on the one hand, we can achieve a certain level of abstraction without being overwhelmed by the underlying implementation details and, on the other hand, we respect the concrete industrial...... standards used for implementing the service-oriented applications. By doing so, we will be able to not only reason about applications at different levels of abstractions, but also to build a bridge between the views of researchers on formal methods and developers in industry. We apply our approach...... to the financial case study taken from Chapter 0-3. Finally, we develop a static analysis to analyse the security properties as they emerge at the level of concrete industrial protocols....

INFRARED SPECTRA, THERMOGRAVIMETRIC ANALYSIS AND ...

African Journals Online (AJOL)

Preferred Customer

2Department of Pesticides Formulation, Central Agricultural Pesticides ... a number of other Fusarium species are able to degrade benzoxazolinone compounds to products which are less inhibitory to fungal growth and also important ...

The intervals method: a new approach to analyse finite element outputs using multivariate statistics

Directory of Open Access Journals (Sweden)

Jordi Marcé-Nogué

2017-10-01

Full Text Available Background In this paper, we propose a new method, named the intervals’ method, to analyse data from finite element models in a comparative multivariate framework. As a case study, several armadillo mandibles are analysed, showing that the proposed method is useful to distinguish and characterise biomechanical differences related to diet/ecomorphology. Methods The intervals’ method consists of generating a set of variables, each one defined by an interval of stress values. Each variable is expressed as a percentage of the area of the mandible occupied by those stress values. Afterwards these newly generated variables can be analysed using multivariate methods. Results Applying this novel method to the biological case study of whether armadillo mandibles differ according to dietary groups, we show that the intervals’ method is a powerful tool to characterize biomechanical performance and how this relates to different diets. This allows us to positively discriminate between specialist and generalist species. Discussion We show that the proposed approach is a useful methodology not affected by the characteristics of the finite element mesh. Additionally, the positive discriminating results obtained when analysing a difficult case study suggest that the proposed method could be a very useful tool for comparative studies in finite element analysis using multivariate statistical approaches.

The intervals method: a new approach to analyse finite element outputs using multivariate statistics

Science.gov (United States)

De Esteban-Trivigno, Soledad; Püschel, Thomas A.; Fortuny, Josep

2017-01-01

Background In this paper, we propose a new method, named the intervals’ method, to analyse data from finite element models in a comparative multivariate framework. As a case study, several armadillo mandibles are analysed, showing that the proposed method is useful to distinguish and characterise biomechanical differences related to diet/ecomorphology. Methods The intervals’ method consists of generating a set of variables, each one defined by an interval of stress values. Each variable is expressed as a percentage of the area of the mandible occupied by those stress values. Afterwards these newly generated variables can be analysed using multivariate methods. Results Applying this novel method to the biological case study of whether armadillo mandibles differ according to dietary groups, we show that the intervals’ method is a powerful tool to characterize biomechanical performance and how this relates to different diets. This allows us to positively discriminate between specialist and generalist species. Discussion We show that the proposed approach is a useful methodology not affected by the characteristics of the finite element mesh. Additionally, the positive discriminating results obtained when analysing a difficult case study suggest that the proposed method could be a very useful tool for comparative studies in finite element analysis using multivariate statistical approaches. PMID:29043107

Evaluation of fracture mechanics analyses used in RPV integrity assessment regarding brittle fracture

International Nuclear Information System (INIS)

Moinereau, D.; Faidy, C.; Valeta, M.P.; Bhandari, S.; Guichard, D.

1997-01-01

Electricite de France has conducted during these last years some experimental and numerical research programmes in order to evaluate fracture mechanics analyses used in nuclear reactor pressure vessels structural integrity assessment, regarding the risk of brittle fracture. These programmes included cleavage fracture tests on large scale cladded specimens containing subclad flaws with their interpretations by 2D and 3D numerical computations, and validation of finite element codes for pressurized thermal shocks analyses. Four cladded specimens made of ferritic steel A508 C13 with stainless steel cladding, and containing shallow subclad flaws, have been tested in four point bending at very low temperature in order to obtain cleavage failure. The specimen failure was obtained in each case in base metal by cleavage fracture. These tests have been interpreted by two-dimensional and three-dimensional finite element computations using different fracture mechanics approaches (elastic analysis with specific plasticity corrections, elastic-plastic analysis, local approach to cleavage fracture). The failure of specimens are conservatively predicted by different analyses. The comparison between the elastic analyses and elastic-plastic analyses shows the conservatism of specific plasticity corrections used in French RPV elastic analyses. Numerous finite element calculations have also been performed between EDF, CEA and Framatome in order to compare and validate several fracture mechanics post processors implemented in finite element programmes used in pressurized thermal shock analyses. This work includes two-dimensional numerical computations on specimens with different geometries and loadings. The comparisons show a rather good agreement on main results, allowing to validate the finite element codes and their post-processors. (author). 11 refs, 24 figs, 3 tabs

Evaluation of fracture mechanics analyses used in RPV integrity assessment regarding brittle fracture

Energy Technology Data Exchange (ETDEWEB)

Moinereau, D [Electricite de France, Dept. MTC, Moret-sur-Loing (France); Faidy, C [Electricite de France, SEPTEN, Villeurbanne (France); Valeta, M P [Commisariat a l` Energie Atomique, Dept. DMT, Gif-sur-Yvette (France); Bhandari, S; Guichard, D [Societe Franco-Americaine de Constructions Atomiques (FRAMATOME), 92 - Paris-La-Defense (France)

1997-09-01

Electricite de France has conducted during these last years some experimental and numerical research programmes in order to evaluate fracture mechanics analyses used in nuclear reactor pressure vessels structural integrity assessment, regarding the risk of brittle fracture. These programmes included cleavage fracture tests on large scale cladded specimens containing subclad flaws with their interpretations by 2D and 3D numerical computations, and validation of finite element codes for pressurized thermal shocks analyses. Four cladded specimens made of ferritic steel A508 C13 with stainless steel cladding, and containing shallow subclad flaws, have been tested in four point bending at very low temperature in order to obtain cleavage failure. The specimen failure was obtained in each case in base metal by cleavage fracture. These tests have been interpreted by two-dimensional and three-dimensional finite element computations using different fracture mechanics approaches (elastic analysis with specific plasticity corrections, elastic-plastic analysis, local approach to cleavage fracture). The failure of specimens are conservatively predicted by different analyses. The comparison between the elastic analyses and elastic-plastic analyses shows the conservatism of specific plasticity corrections used in French RPV elastic analyses. Numerous finite element calculations have also been performed between EDF, CEA and Framatome in order to compare and validate several fracture mechanics post processors implemented in finite element programmes used in pressurized thermal shock analyses. This work includes two-dimensional numerical computations on specimens with different geometries and loadings. The comparisons show a rather good agreement on main results, allowing to validate the finite element codes and their post-processors. (author). 11 refs, 24 figs, 3 tabs.

Antimicrobial Properties of Chitosan-Alumina/f-MWCNT Nano composites

International Nuclear Information System (INIS)

Masheane, M.; Nthunya, L.; Malinga, S.; Masheane, M.; Nthunya, L.; Nxumalo, E.; Mhlanga, S.; Barnard, T.

2016-01-01

Antimicrobial chitosan-alumina/functionalized-multi walled carbon nano tube (f-MWCNT) nano composites were prepared by a simple phase inversion method. Scanning electron microscopy (SEM) analyses showed the change in the internal morphology of the composites and energy dispersive spectroscopy (EDS) confirmed the presence of alumina and f-MWCNTs in the chitosan polymer matrix. Fourier transform infrared (FTIR) spectroscopy showed the appearance of new functional groups from both alumina and f-MWCNTs, and thermogravimetric analysis (TGA) revealed that the addition of alumina and f-MWCNTs improved the thermal stability of the chitosan polymer. The presence of alumina and f-MWCNTs in the polymer matrix was found to improve the thermal stability and reduced the solubility of chitosan polymer. The prepared chitosan-alumina/f-MWCNT nano composites showed inhibition of twelve strains of bacterial strains that were tested. Thus, the nano composites show a potential for use as a biocides in water treatment for the removal of bacteria at different environmental conditions.

Analyses of residual iron in carbon nanotubes produced by camphor/ferrocene pyrolysis and purified by high temperature annealing

Energy Technology Data Exchange (ETDEWEB)

Antunes, E.F., E-mail: ericafa@las.inpe.br [Instituto Tecnologico de Aeronautica (ITA), Praca Marechal Eduardo Gomes, 50, CEP 12.228-900, Sao Jose dos Campos, SP (Brazil); Instituto Nacional de Pesquisas Espaciais (INPE), Av. dos Astronautas, 1758, CEP 12.227-010, Sao Jose dos Campos, SP (Brazil); Resende, V.G. de; Mengui, U.A. [Instituto Nacional de Pesquisas Espaciais (INPE), Av. dos Astronautas, 1758, CEP 12.227-010, Sao Jose dos Campos, SP (Brazil); Cunha, J.B.M. [Universidade Federal do Rio Grande do Sul (UFRGS), Av. Bento Goncalves, 9500, CEP 91.501-970, Porto Alegre, RS (Brazil); Corat, E.J.; Massi, M. [Instituto Nacional de Pesquisas Espaciais (INPE), Av. dos Astronautas, 1758, CEP 12.227-010, Sao Jose dos Campos, SP (Brazil)

2011-07-01

A detailed analysis of iron-containing phases in multiwall carbon nanotube (MWCNT) powder was carried out. The MWCNTs were produced by camphor/ferrocene and purified by high temperature annealing in an oxygen-free atmosphere (N{sub 2} or VC). Thermogravimetric analysis, Moessbauer spectroscopy, X-ray diffraction and X-ray photoelectron spectroscopy enabled the evaluation of the residual iron in MWCNTs after purification. The VC treatments provided MWCNTs with a purity degree higher than 99%. Moreover, Raman spectroscopy revealed a significant improvement in graphitic ordering after thermal annealing. A brief description of the mechanism of iron removal was included. We highlight the mobility of iron atoms through graphitic sheets and the large contact angle of iron clusters formed on MWCNT surfaces at high temperatures.

Recurrent and multiple bladder tumors show conserved expression profiles

International Nuclear Information System (INIS)

Lindgren, David; Fioretos, Thoas; Månsson, Wiking; Höglund, Mattias; Gudjonsson, Sigurdur; Jee, Kowan Ja; Liedberg, Fredrik; Aits, Sonja; Andersson, Anna; Chebil, Gunilla; Borg, Åke; Knuutila, Sakari

2008-01-01

Urothelial carcinomas originate from the epithelial cells of the inner lining of the bladder and may appear as single or as multiple synchronous tumors. Patients with urothelial carcinomas frequently show recurrences after treatment making follow-up necessary. The leading hypothesis explaining the origin of meta- and synchronous tumors assumes a monoclonal origin. However, the genetic relationship among consecutive tumors has been shown to be complex in as much as the genetic evolution does not adhere to the chronological appearance of the metachronous tumors. Consequently, genetically less evolved tumors may appear chronologically later than genetically related but more evolved tumors. Forty-nine meta- or synchronous urothelial tumors from 22 patients were analyzed using expression profiling, conventional CGH, LOH, and mutation analyses. We show by CGH that partial chromosomal losses in the initial tumors may not be present in the recurring tumors, by LOH that different haplotypes may be lost and that detected regions of LOH may be smaller in recurring tumors, and that mutations present in the initial tumor may not be present in the recurring ones. In contrast we show that despite apparent genomic differences, the recurrent and multiple bladder tumors from the same patients display remarkably similar expression profiles. Our findings show that even though the vast majority of the analyzed meta- and synchronous tumors from the same patients are not likely to have originated directly from the preceding tumor they still show remarkably similar expressions profiles. The presented data suggests that an expression profile is established early in tumor development and that this profile is stable and maintained in recurring tumors

Synthesis and characterization of Sm0.5Ba0.5MnO3-δ as anode materials for solid oxide fuel cells

International Nuclear Information System (INIS)

Abdalla, A. M.; Radenahmad, N.; Bakar, M. S. Abu; Petra, Pg M .I.; Azad, A. K.

2016-01-01

The material performance is a crucial issue in the current fuel cell technology, and for this reason we present this new series of Samarium family which can be used as electrode giving a high performance in a particular application. Sm 0 . 5 Ba 0 . 5 MnO 3-δ was prepared by solid state reaction method and characterized by using X-ray diffraction (XRD), and thermogravimetric analysis (TGA). Rietveld analysis of XRD data shows that the material has an Orthorhombic crystal structure with cell parameter a = 3.883(1) Å b = 3.8742(5) Å c = 7. 762(4) Å, in the Pmmm space group. TGA analyses shows that the materials is going to decrease by 0.32%. The density of the materials was calculated from structural refinement and found to be 8.372 gm/cm 3 . (paper)

Influence of temperature on oxidation behaviour of ZE41 magnesium alloy

International Nuclear Information System (INIS)

Lopez, M.D.; Munez, C.J.; Carboneras, M.; Rodrigo, P.; Escalera, M.D.; Otero, E.

2010-01-01

The influence of temperature on the oxidation behaviour of commercial ZE41 magnesium alloy has been studied. Thermogravimetric tests were carried out to determine the oxidation kinetics in the 350-500 o C range. Morphology and growth of the oxidation films were analysed by Scanning Electronic Microscopy (SEM), Energy Dispersive X-Ray Spectrometry (EDS) and X-Ray Diffraction (XRD). It was found that the oxidation kinetics initially follow a parabolic law, following a linear law for higher exposure times. Results also showed that the protective nature of the oxide layer depends on the oxidation temperature. At temperatures in the range of 350-450 o C the ZE41 alloy is covered by a protective oxide layer, very thin and compact, whereas the oxide layer formed at 500 o C exhibits a non-protective nature, showing an 'oxide sponges' morphology.

Investigation of Zircaloy-2 oxidation model for SFP accident analysis

Energy Technology Data Exchange (ETDEWEB)

Nemoto, Yoshiyuki, E-mail: nemoto.yoshiyuki@jaea.go.jp [Japan Atomic Energy Agency, 2-4 Shirakata, Ohaza, Tokai-mura, Naka-gun, Ibaraki, 319-1195 (Japan); Kaji, Yoshiyuki; Ogawa, Chihiro; Kondo, Keietsu [Japan Atomic Energy Agency, 2-4 Shirakata, Ohaza, Tokai-mura, Naka-gun, Ibaraki, 319-1195 (Japan); Nakashima, Kazuo; Kanazawa, Toru; Tojo, Masayuki [Global Nuclear Fuel – Japan Co., Ltd., 2-3-1, Uchikawa, Yokosuka-shi, Kanagawa, 239-0836 (Japan)

2017-05-15

The authors previously conducted thermogravimetric analyses on Zircaloy-2 in air. By using the thermogravimetric data, an oxidation model was constructed in this study so that it can be applied for the modeling of cladding degradation in spent fuel pool (SFP) severe accident condition. For its validation, oxidation tests of long cladding tube were conducted, and computational fluid dynamics analyses using the constructed oxidation model were proceeded to simulate the experiments. In the oxidation tests, high temperature thermal gradient along the cladding axis was applied and air flow rates in testing chamber were controlled to simulate hypothetical SFP accidents. The analytical outputs successfully reproduced the growth of oxide film and porous oxide layer on the claddings in oxidation tests, and validity of the oxidation model was proved. Influence of air flow rate for the oxidation behavior was thought negligible in the conditions investigated in this study. - Highlights: •An oxidation model of Zircaloy-2 in air environment was developed. •The oxidation model was validated by the comparison with oxidation tests using long cladding tubes in hypothetical spent fuel pool accident condition. •The oxidation model successfully reproduced the typical oxidation behavior in air.

Use of Thermoanalytic Methods in the Evaluation of Combusted Materials

Directory of Open Access Journals (Sweden)

František Krepelka

2006-12-01

Full Text Available The paper describes possibilities of using thermoanalytic methods for the evaluation and comparison of materials designed for a direct combustion. Differential thermal analysis (DTA and thermogravimetric analysis (TGA were both used in the evaluation. The paper includes a description of methods of data processing from analyses for the purposes of comparison of used materials regarding their heating values. The following materials were analysed in the experiments: wooden coal of objectional grain size, fly ash from heating plant exhaust funnels, dendromass waste: spruce sawdust, micro-briquettes of spruce sawdust and fly-ash combined.

Large-Scale No-Show Patterns and Distributions for Clinic Operational Research

Directory of Open Access Journals (Sweden)

Michael L. Davies

2016-02-01

Full Text Available Patient no-shows for scheduled primary care appointments are common. Unused appointment slots reduce patient quality of care, access to services and provider productivity while increasing loss to follow-up and medical costs. This paper describes patterns of no-show variation by patient age, gender, appointment age, and type of appointment request for six individual service lines in the United States Veterans Health Administration (VHA. This retrospective observational descriptive project examined 25,050,479 VHA appointments contained in individual-level records for eight years (FY07-FY14 for 555,183 patients. Multifactor analysis of variance (ANOVA was performed, with no-show rate as the dependent variable, and gender, age group, appointment age, new patient status, and service line as factors. The analyses revealed that males had higher no-show rates than females to age 65, at which point males and females exhibited similar rates. The average no-show rates decreased with age until 75–79, whereupon rates increased. As appointment age increased, males and new patients had increasing no-show rates. Younger patients are especially prone to no-show as appointment age increases. These findings provide novel information to healthcare practitioners and management scientists to more accurately characterize no-show and attendance rates and the impact of certain patient factors. Future general population data could determine whether findings from VHA data generalize to others.

Large-Scale No-Show Patterns and Distributions for Clinic Operational Research.

Science.gov (United States)

Davies, Michael L; Goffman, Rachel M; May, Jerrold H; Monte, Robert J; Rodriguez, Keri L; Tjader, Youxu C; Vargas, Dominic L

2016-02-16

Patient no-shows for scheduled primary care appointments are common. Unused appointment slots reduce patient quality of care, access to services and provider productivity while increasing loss to follow-up and medical costs. This paper describes patterns of no-show variation by patient age, gender, appointment age, and type of appointment request for six individual service lines in the United States Veterans Health Administration (VHA). This retrospective observational descriptive project examined 25,050,479 VHA appointments contained in individual-level records for eight years (FY07-FY14) for 555,183 patients. Multifactor analysis of variance (ANOVA) was performed, with no-show rate as the dependent variable, and gender, age group, appointment age, new patient status, and service line as factors. The analyses revealed that males had higher no-show rates than females to age 65, at which point males and females exhibited similar rates. The average no-show rates decreased with age until 75-79, whereupon rates increased. As appointment age increased, males and new patients had increasing no-show rates. Younger patients are especially prone to no-show as appointment age increases. These findings provide novel information to healthcare practitioners and management scientists to more accurately characterize no-show and attendance rates and the impact of certain patient factors. Future general population data could determine whether findings from VHA data generalize to others.

Fractal and multifractal analyses of bipartite networks

Science.gov (United States)

Liu, Jin-Long; Wang, Jian; Yu, Zu-Guo; Xie, Xian-Hua

2017-03-01

Bipartite networks have attracted considerable interest in various fields. Fractality and multifractality of unipartite (classical) networks have been studied in recent years, but there is no work to study these properties of bipartite networks. In this paper, we try to unfold the self-similarity structure of bipartite networks by performing the fractal and multifractal analyses for a variety of real-world bipartite network data sets and models. First, we find the fractality in some bipartite networks, including the CiteULike, Netflix, MovieLens (ml-20m), Delicious data sets and (u, v)-flower model. Meanwhile, we observe the shifted power-law or exponential behavior in other several networks. We then focus on the multifractal properties of bipartite networks. Our results indicate that the multifractality exists in those bipartite networks possessing fractality. To capture the inherent attribute of bipartite network with two types different nodes, we give the different weights for the nodes of different classes, and show the existence of multifractality in these node-weighted bipartite networks. In addition, for the data sets with ratings, we modify the two existing algorithms for fractal and multifractal analyses of edge-weighted unipartite networks to study the self-similarity of the corresponding edge-weighted bipartite networks. The results show that our modified algorithms are feasible and can effectively uncover the self-similarity structure of these edge-weighted bipartite networks and their corresponding node-weighted versions.

Thermogravimetric and Kinetic Analysis of Cassava Starch Based Bioplastic

Directory of Open Access Journals (Sweden)

Nanang Eko Wahyuningtyas

2017-11-01

Full Text Available Cassava starch based bioplasticfor packaging application has great potency because of the various starch-producing plants in Indonesia.Bioplasticcan contribute to reduce the dependence on fossil fuels andpetroleumthat can solve the environmentalproblem.Thepurpose of this research is to find out the thermal decomposition and the activation energy of cassava starch based bioplastic. The methods weresynthesis bioplastic with cassava starch as main component and glycerol as plasticizer. The thermogravimetry analysis was conducted to obtain the decomposition process mechanism of bioplastic and the heating valueof bioplasticwas measured  using theadiabatic bomb calorimetric.  Data analysis was conducted using  a fitting model approach with an acikalin method to determine the activation energy. The result of thethermogravimetricanalysis showed thatbioplasticisgraduallydecomposedto the moisture, volatilematter, fixed carbon, andash in four stages mechanism. Totally decomposition of bioplastic was 530°C, then all of bioplastic was become the ash. The activation energy in the early and primary thermal decomposition stages are 1.27 kJ/moland 22.62 kJ/mol, respectively and heating valueof bioplastic is 15.16 MJ/kg.

Zinc(II) halide complexes with 2-methoxyaniline ligand: Synthesis, characterization, thermal analyses, crystal structure determination and luminescent properties

Science.gov (United States)

Amani, Vahid

2018-03-01

Three new mononuclear zinc(II) complexes, [Zn(2-MeO-C6H4NH2)2X2] (X is Cl in 1, Br in 2 and I in 3), were prepared from the reactions of ZnX2 with 2-methoxyaniline (2-MeO-C6H4NH2) ligand in methanol. Suitable crystals of these complexes were obtained for X-ray diffraction measurements by slow evaporation of methanol solution at room temperature. The three complexes were thoroughly characterized by thermogravimetric analysis, elemental analysis (CHNO), spectral methods (IR, UV-Vis, 13C{1H}NMR, 1H NMR and luminescence), and single crystal X-ray diffraction. The X-ray structural analysis indicated that in the structures of these complexes, the zinc(II) cation is four-coordinated in a distorted tetrahedral configuration by two N atoms from two 2-methoxyanyline ligands and two halide anions. Also, in these complexes intermolecular interactions, for example Nsbnd H⋯X hydrogen bonds (in 1-3), Csbnd H⋯X hydrogen bonds (in 3), Csbnd H⋯π interactions (in 1 and 2) and π⋯π interactions (in 3), are effective in the stabilization of the crystal structures. In addition, the luminescence spectra of all complexes in methanolic solution show that the intensity of their emission bands is stronger than that for free 2-methoxyaniline ligand.

Altered Brain Activity in Unipolar Depression Revisited: Meta-analyses of Neuroimaging Studies.

Science.gov (United States)

Müller, Veronika I; Cieslik, Edna C; Serbanescu, Ilinca; Laird, Angela R; Fox, Peter T; Eickhoff, Simon B

2017-01-01

During the past 20 years, numerous neuroimaging experiments have investigated aberrant brain activation during cognitive and emotional processing in patients with unipolar depression (UD). The results of those investigations, however, vary considerably; moreover, previous meta-analyses also yielded inconsistent findings. To readdress aberrant brain activation in UD as evidenced by neuroimaging experiments on cognitive and/or emotional processing. Neuroimaging experiments published from January 1, 1997, to October 1, 2015, were identified by a literature search of PubMed, Web of Science, and Google Scholar using different combinations of the terms fMRI (functional magnetic resonance imaging), PET (positron emission tomography), neural, major depression, depression, major depressive disorder, unipolar depression, dysthymia, emotion, emotional, affective, cognitive, task, memory, working memory, inhibition, control, n-back, and Stroop. Neuroimaging experiments (using fMRI or PET) reporting whole-brain results of group comparisons between adults with UD and healthy control individuals as coordinates in a standard anatomic reference space and using an emotional or/and cognitive challenging task were selected. Coordinates reported to show significant activation differences between UD and healthy controls during emotional or cognitive processing were extracted. By using the revised activation likelihood estimation algorithm, different meta-analyses were calculated. Meta-analyses tested for brain regions consistently found to show aberrant brain activation in UD compared with controls. Analyses were calculated across all emotional processing experiments, all cognitive processing experiments, positive emotion processing, negative emotion processing, experiments using emotional face stimuli, experiments with a sex discrimination task, and memory processing. All meta-analyses were calculated across experiments independent of reporting an increase or decrease of activity in

Implementing partnerships in nonreactor facility safety analyses

International Nuclear Information System (INIS)

Courtney, J.C.; Perry, W.H.; Phipps, R.D.

1996-01-01

Faculty and students from LSU have been participating in nuclear safety analyses and radiation protection projects at ANL-W at INEL since 1973. A mutually beneficial relationship has evolved that has resulted in generation of safety-related studies acceptable to Argonne and DOE, NRC, and state regulatory groups. Most of the safety projects have involved the Hot Fuel Examination Facility or the Fuel Conditioning Facility; both are hot cells that receive spent fuel from EBR-II. A table shows some of the major projects at ANL-W that involved LSU students and faculty

Effects of eco-friendly carbohydrate-based superabsorbent polymers on seed germination and seedling growth of maize

Science.gov (United States)

Tao, Jinghe; Zhang, Wenxu; Liang, Li; Lei, Ziqiang

2018-02-01

Desertification is the degradation of land in arid and semi-arid areas. Nowadays, lack of water and desertification are extreme problems for plant survival and growth in the arid and semi-arid areas of the world. It becomes increasingly important as to how to let the plant absorb moisture more effectively for keeping growth strong. We synthesized superabsorbent polymers (SAPs) with carbohydrate and characterized them by Fourier transform infrared spectra analyses, scanning electron microscopy and thermogravimetric/differential thermal analyses. Then, a completely randomized experiment was conducted to assess the effect of carbohydrate-based SAPs on seed germination and seedling growth of maize in an artificial climate chest. The results showed that adding an appropriate amount of SAPs could improve root length, shoot length, total biomass, germination potential and germination rate. It indicates that this SAP is not toxic to plants and can promote seed germination, and at the same time provides a possibility of replacing other substrates.

Two novel metal-organic coordination polymers based on diphosphonate and oxalate: Synthesis, structures and properties

Science.gov (United States)

Niu, Qing-Jun; Zheng, Yue-Qing; Zhou, Lin-Xia; Zhu, Hong-Lin

2015-07-01

Two 2-(1-imidazole)-1-hydroxyl-1,1'-ethylidenediphosphonato and oxalic acid bridged coordination polymers (H2en)[Co3(H2zdn)2(ox)(H2O)2] (1) and Cd2(H2zdn)(ox)0.5(H2O) (2) (2-(1-imidazole)-1-hydroxyl-1,1'-ethylidenediphosphonic acid=H5zdn; oxalic acid=H2ox) were synthesized under hydrothermal conditions and characterized by the infrared (IR), thermogravimetric analyses (TGA), elemental analyses (EA) and X-ray diffraction (XRD). Compound 1 is bridged by phosphonate anions to 1D chain, and further linked by oxalate anions to 2D layer. Compound 2 is bridged by O-P-O units of H5zdn to the layer, and then pillared by oxalate anions to generate 3D frameworks. Compound 1 shows anti-ferromagnetic behaviors analyzed with the temperature-dependent zero-field ac magnetic susceptibilities, while compound 2 exhibits an influence on the luminescent property.

Intermolecular and very strong intramolecular C-SeO/N chalcogen bonds in nitrophenyl selenocyanate crystals.

Science.gov (United States)

Wang, Hui; Liu, Ju; Wang, Weizhou

2018-02-14

Single-crystal X-ray diffraction reveals that polymorphic ortho-nitrophenyl selenocyanate (o-NSC, crystals 1a and 1b) and monomorphic para-nitrophenyl selenocyanate (p-NSC, crystal 2) crystals are all stabilized mainly by intermolecular and very strong intramolecular C-SeO/N chalcogen bonds, as well as by other different interactions. Thermogravimetric (TG) and differential scanning calorimetry thermogram (DSC) analyses show that the starting decomposition temperatures and melting points of the three crystals are different, following the order 1b > 1a > 2, which is consistent with the structural characteristics of the crystals. In addition, atoms in molecules (AIM) and natural bond orbital (NBO) analyses indicate that the total strengths of the C-SeO and C-SeN chalcogen bonds decrease in the order 1b > 1a > 2. This study could be significant for engineering functional crystals based on robust C-SeO and C-SeN chalcogen bonds, and for designing drugs containing selenium as well as understanding their interaction in biosystems.

Effects of eco-friendly carbohydrate-based superabsorbent polymers on seed germination and seedling growth of maize

Science.gov (United States)

Tao, Jinghe; Liang, Li; Lei, Ziqiang

2018-01-01

Desertification is the degradation of land in arid and semi-arid areas. Nowadays, lack of water and desertification are extreme problems for plant survival and growth in the arid and semi-arid areas of the world. It becomes increasingly important as to how to let the plant absorb moisture more effectively for keeping growth strong. We synthesized superabsorbent polymers (SAPs) with carbohydrate and characterized them by Fourier transform infrared spectra analyses, scanning electron microscopy and thermogravimetric/differential thermal analyses. Then, a completely randomized experiment was conducted to assess the effect of carbohydrate-based SAPs on seed germination and seedling growth of maize in an artificial climate chest. The results showed that adding an appropriate amount of SAPs could improve root length, shoot length, total biomass, germination potential and germination rate. It indicates that this SAP is not toxic to plants and can promote seed germination, and at the same time provides a possibility of replacing other substrates. PMID:29515838

Publication bias in dermatology systematic reviews and meta-analyses.

Science.gov (United States)

Atakpo, Paul; Vassar, Matt

2016-05-01

Systematic reviews and meta-analyses in dermatology provide high-level evidence for clinicians and policy makers that influence clinical decision making and treatment guidelines. One methodological problem with systematic reviews is the under representation of unpublished studies. This problem is due in part to publication bias. Omission of statistically non-significant data from meta-analyses may result in overestimation of treatment effect sizes which may lead to clinical consequences. Our goal was to assess whether systematic reviewers in dermatology evaluate and report publication bias. Further, we wanted to conduct our own evaluation of publication bias on meta-analyses that failed to do so. Our study considered systematic reviews and meta-analyses from ten dermatology journals from 2006 to 2016. A PubMed search was conducted, and all full-text articles that met our inclusion criteria were retrieved and coded by the primary author. 293 articles were included in our analysis. Additionally, we formally evaluated publication bias in meta-analyses that failed to do so using trim and fill and cumulative meta-analysis by precision methods. Publication bias was mentioned in 107 articles (36.5%) and was formally evaluated in 64 articles (21.8%). Visual inspection of a funnel plot was the most common method of evaluating publication bias. Publication bias was present in 45 articles (15.3%), not present in 57 articles (19.5%) and not determined in 191 articles (65.2%). Using the trim and fill method, 7 meta-analyses (33.33%) showed evidence of publication bias. Although the trim and fill method only found evidence of publication bias in 7 meta-analyses, the cumulative meta-analysis by precision method found evidence of publication bias in 15 meta-analyses (71.4%). Many of the reviews in our study did not mention or evaluate publication bias. Further, of the 42 articles that stated following PRISMA reporting guidelines, 19 (45.2%) evaluated for publication bias. In

Thermogravimetric and Kinetic Analysis of Raw and Torrefied Biomass Combustion

Directory of Open Access Journals (Sweden)

Kopczyński Marcin

2015-06-01

Full Text Available The use of torrefied biomass as a substitute for untreated biomass may decrease some technological barriers that exist in biomass co-firing technologies e.g. low grindability, high moisture content, low energy density and hydrophilic nature of raw biomass. In this study the TG-MS-FTIR analysis and kinetic analysis of willow (Salix viminalis L. and samples torrefied at 200, 220, 240, 260, 280 and 300 °C (TSWE 200, 220, 240, 260, 280 and 300, were performed. The TG-DTG curves show that in the case of willow and torrefied samples TSWE 200, 220, 240 and 260 there are pyrolysis and combustion stages, while in the case of TSWE 280 and 300 samples the peak associated with the pyrolysis process is negligible, in contrast to the peak associated with the combustion process. Analysis of the TG-MS results shows m/z signals of 18, 28, 29 and 44, which probably represent H2O, CO and CO2. The gaseous products were generated in two distinct ranges of temperature. H2O, CO and CO2 were produced in the 500 K to 650 K range with maximum yields at approximately 600 K. In the second range of temperature, 650 K to 800 K, only CO2 was produced with maximum yields at approximately 710 K as a main product of combustion process. Analysis of the FTIR shows that the main gaseous products of the combustion process were H2O, CO2, CO and some organics including bonds: C=O (acids, aldehydes and ketones, C=C (alkenes, aromatics, C-O-C (ethers and C-OH. Lignin mainly contributes hydrocarbons (3000-2800 cm−1, while cellulose is the dominant origin of aldehydes (2860-2770 cm−1 and carboxylic acids (1790-1650 cm−1. Hydrocarbons, aldehydes, ketones and various acids were also generated from hemicellulose (1790-1650 cm−1. In the kinetic analysis, the two-steps first order model (F1F1 was assumed. Activation energy (Ea values for the first stage (pyrolysis increased with increasing torrefaction temperature from 93 to 133 kJ/mol, while for the second stage (combustion it

Studies on trivalent lanthanide complexes of bis-vanillin p-phenylenediamine

International Nuclear Information System (INIS)

Shahma, Abu; Ahmad, Naseer

1983-01-01

The coordination interaction of lanthanide(III) chlorides with bis-vanillin o-phenylenediamine was studied by Ansari and Ahmad (1977). It was thought fruitful to compare these with the complexes of trivalent lanthanide ions with bis-vanillin p-phenylenediamine. The newly synthesized complexes were subjected to elemental, thermogravimetric and differential thermal analyses and their melting points, magnetic susceptibilities, molar conductances determined and infrared and electronic spectra taken. (author)

Surface Modification of Magnetic Nanoparticles Using Gum Arabic

International Nuclear Information System (INIS)

Williams, Darryl N.; Gold, Katie A.; Holoman, Tracey R. Pulliam; Ehrman, Sheryl H.; Wilson, Otto C.

2006-01-01

Magnetite nanoparticles were synthesized and functionalized by coating the particle surfaces with gum arabic (GA) to improve particle stability in aqueous suspensions (i.e. biological media). Particle characterization was performed using transmission electron microscopy (TEM) and dynamic light scattering (DLS) to analyze the morphology and quantify the size distribution of the nanoparticles, respectively. The results from DLS indicated that the GA-treated nanoparticles formed smaller agglomerates as compared to the untreated samples over a 30-h time frame. Thermogravimetric analyses indicated an average weight loss of 23%, showing that GA has a strong affinity toward the iron oxide surface. GA most likely contributes to colloid stability via steric stabilization. It was determined that the adsorption of GA onto magnetite exhibits Langmuir behavior

Desorption process of hydrogen starting from the Mg{sub 2}NiH{sub 4} and Mg{sub 2}NiH{sub 0.3}; Proceso de desorcion de hidrogeno a partir del hidruro intermetalico Mg{sub 2}NiH{sub 4} y Mg{sub 2}NiH{sub 0.3}

Energy Technology Data Exchange (ETDEWEB)

Iturbe G, J.L.; Basurto S, R.; Lopez M, B.E. [Departamento de Quimica, ININ, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

2002-07-01

In this work the desorption velocity of H{sub 2} was determined starting from the magnesium nickel hydride once the reaction between the intermetallic and the hydrogen was realized, the compound were analysed by means of a thermogravimetric equipment, the conditions for carrying out the analysis were: 10 C by minute in nitrogen atmosphere at a volume of 50 ml by minute, subsequently the isotherms at different times were programmed and the desorption velocity of hydrogen was determined. The results show that the desorption velocity of hydrogen depends of the temperature, using only the nitrogen flux which acts as a carrier gas. Observing that the hydrogen liberation is carried out by means of two mechanisms according to the isotherms obtained. (Author)

Modification of a cellulose derived for your application on enzyme immobilization;Modificacao de um derivado celulosico para sua aplicacao na imobilizacao de enzimas

Energy Technology Data Exchange (ETDEWEB)

Carvalho, Elaine S.; Rodriguez, Ruben J.S.; Lamonica, Alano C., E-mail: ecarvalho@uenf.b [Universidade Estadual do Norte Fluminense Darcy Ribeiro (LAMAV/UENF), Campos dos Goytacazes, RJ (Brazil). Lab. de Materiais Avancados; Tavares, Maria Ines B. [Universidade Federal do Rio de Janeiro (IMA/UFRJ), RJ (Brazil). Inst. de Macromoleculas Profa. Eloisa Mano

2009-07-01

The chemical modification of (acrylamidomethyl) cellulose acetate propionate (AMCAP) was done through the technique of grafting via radical using acrylic acid as modifier, with the objective to make the polymer more hydrophilic. The structural characterization of AMCAP and modified AMCAP-H{sub 2}O{sub 2} was analysed by using the technique of {sup 13}C-nuclear magnetic resonance (NMR-{sup 13}C). By the techniques differential scanning calorimetry analysis (DSC) and thermogravimetric analysis (TGA), the thermal properties was characterized and the hydrophobic / hydrophilic character was determined by measurements of the contact angle. The results show that occurred the change intended with the introduction of acrylic acid in the side chain of the polymer, increasing the hydrophilic character on the AMCAP. (author)

Desorption process of hydrogen starting from the Mg2NiH4 and Mg2NiH0.3

International Nuclear Information System (INIS)

Iturbe G, J.L.; Basurto S, R.; Lopez M, B.E.

2002-01-01

In this work the desorption velocity of H 2 was determined starting from the magnesium nickel hydride once the reaction between the intermetallic and the hydrogen was realized, the compound were analysed by means of a thermogravimetric equipment, the conditions for carrying out the analysis were: 10 C by minute in nitrogen atmosphere at a volume of 50 ml by minute, subsequently the isotherms at different times were programmed and the desorption velocity of hydrogen was determined. The results show that the desorption velocity of hydrogen depends of the temperature, using only the nitrogen flux which acts as a carrier gas. Observing that the hydrogen liberation is carried out by means of two mechanisms according to the isotherms obtained. (Author)

Combustion of Sewage Sludge as Alternative Fuel for Cement Industry

Institute of Scientific and Technical Information of China (English)

LI Fuzhou; ZHANG Wei

2011-01-01

The combustion of sewage sludge and coal was studied by thermogravimetric analysis.Both differential scanning calorimetric analysis and derivative thermogravimetric profiles showed differences between combustion of sewage sludge and coal, and non-isothermal kinetics analysis method was applied to evaluate the combustion process. Based on Coats-Redfem integral method, some reaction models were tested,the mechanism and kinetics of the combustion reaction were discussed. The results show that the combustion of sewage sludge is mainly in the Iow temperature stage, meanwhile the ignition temperature and Arrhenius activation energy are lower than that of coal. The combustion of sewage sludge has the advantage over coal in some aspects, thus sewage sludge can partly replace coal used as cement industry fuel.

Laser Beam Focus Analyser

DEFF Research Database (Denmark)

Nielsen, Peter Carøe; Hansen, Hans Nørgaard; Olsen, Flemming Ove

2007-01-01

the obtainable features in direct laser machining as well as heat affected zones in welding processes. This paper describes the development of a measuring unit capable of analysing beam shape and diameter of lasers to be used in manufacturing processes. The analyser is based on the principle of a rotating......The quantitative and qualitative description of laser beam characteristics is important for process implementation and optimisation. In particular, a need for quantitative characterisation of beam diameter was identified when using fibre lasers for micro manufacturing. Here the beam diameter limits...... mechanical wire being swept through the laser beam at varying Z-heights. The reflected signal is analysed and the resulting beam profile determined. The development comprised the design of a flexible fixture capable of providing both rotation and Z-axis movement, control software including data capture...

Prediction of Seismic Slope Displacements by Dynamic Stick-Slip Analyses

International Nuclear Information System (INIS)

Ausilio, Ernesto; Costanzo, Antonio; Silvestri, Francesco; Tropeano, Giuseppe

2008-01-01

A good-working balance between simplicity and reliability in assessing seismic slope stability is represented by displacement-based methods, in which the effects of deformability and ductility can be either decoupled or coupled in the dynamic analyses. In this paper, a 1D lumped mass ''stick-slip'' model is developed, accounting for soil heterogeneity and non-linear behaviour, with a base sliding mechanism at a potential rupture surface. The results of the preliminary calibration show a good agreement with frequency-domain site response analysis in no-slip conditions. The comparison with rigid sliding block analyses and with the decoupled approach proves that the stick-slip procedure can result increasingly unconservative for soft soils and deep sliding depths

Effect of humidity on the hydration behaviour of prazosin hydrochloride polyhydrate: Thermal, sorption and crystallographic study

International Nuclear Information System (INIS)

Kumar, Lokesh; Bansal, Arvind K.

2011-01-01

Highlights: → Utility of TGA to differentiate between unbound and bound water was demonstrated. → Nature of the lattice arrangement in prazosin hydrochloride polyhydrate was confirmed to be expanded (non-stoichiometric) type hydrate. → Correlation of the DSC, TGA, PXRD and DVS for dehydration of prazosin hydrochloride polyhydrate was delineated. - Abstract: In this study, hydration behaviour of prazosin hydrochloride polyhydrate was assessed using differential scanning calorimetry, thermogravimetric analysis, powder X-ray diffraction and dynamic vapour sorption techniques. Differential scanning calorimetry and thermogravimetric analysis at faster heating rate (20 o C/min) showed single step water loss, attributed to both dihydrate and unbound water. In contrast, thermogravimetric analysis at slower heating rate (1 o C/min) showed unbound and dihydrate lattice water separately, with unbound water being lost initially, followed by loss of dihydrate water. Variable vacuum and variable humidity PXRD study revealed shift in diffraction peaks to higher values on removal of unbound water. Initial PXRD patterns were regained when kept again at ambient conditions. Dynamic vapour sorption depicted type I sorption isotherm with interstitial water, indicating that polyhydrate form show reversible behaviour with change in humidity. Correlation between thermal, sorption and crystallographic data established hydration behaviour to be characteristic of expanded channel type (non-stoichiometric) hydrate.

DETERMINATION OF SATURATION VAPOR PRESSURE OF LOW VOLATILE SUBSTANCES THROUGH THE STUDY OF EVAPORATION RATE BY THERMOGRAVIMETRIC ANALYSIS

Directory of Open Access Journals (Sweden)

R. V. Ralys

2015-11-01

Full Text Available Subject of Study.Research of vapor pressure of low volatile substances is a complicated problem due to both direct experimental implementation complexity and, most significantly, the issues faced correctness of the analysis and processing of experimental data. That is why it is usually required engaging the reference substances (with vapor pressures well studied. The latter drastically reduces the effectiveness of the experimental methods used and narrows their applicability. The paper deals with an approach to the evaporation process description (sublimation of low volatile substances based on molecular kinetic description in view of diffusive and convection processes. The proposed approach relies on experimental thermogravimetricfindingsina wide range of temperatures, flow rates ofthe purge gas and time. Method. A new approach is based on the calculation of the vapor pressure and uses the data about the speed of evaporation by thermogravimetric analysis depending on the temperature, the flow rate of the purge gas, and the evaporation time. The basis for calculation is the diffusion-kinetic description of the process of evaporation (mass loss of the substance from the exposed surface. The method is applicable to determine the thermodynamic characteristics for both the evaporation (the equilibrium liquid - vapor and sublimation (the equilibrium solid - vapor. We proposed the appropriate method of the experiment and analysis of its data in order to find the saturated vapor pressure of individual substances of low volatility. Main Results. The method has been tested on substances with insufficiently reliable and complete study of the thermodynamic characteristics but, despite this, are often used (because of the other data limitations as reference ones. The vaporization process (liquid-vapor has been studied for di-n-butyl phthalate C16H22O4 at 323,15–443,15 К, and sublimation for benzoic acid C7H6O2at 303,15–183,15 К. Both processes have

Estudo termogravimétrico do processo de sorção de metais pesados por resíduos sólidos orgânicos Thermogravimetric study of the sorption process of heavy metals in organic solid waste

Directory of Open Access Journals (Sweden)

Aldre Jorge Morais Barros

2006-06-01

thermogravimetric technique. The results obtained demonstrated that the profiles of the thermogravimetric curves of the organic solid waste presented significant modifications in the physical and chemical characteristics when submitted to the heavy metal sorption process.

Hydrogen Analyses in the EPR

International Nuclear Information System (INIS)

Worapittayaporn, S.; Eyink, J.; Movahed, M.

2008-01-01

In severe accidents with core melting large amounts of hydrogen may be released into the containment. The EPR provides a combustible gas control system to prevent hydrogen combustion modes with the potential to challenge the containment integrity due to excessive pressure and temperature loads. This paper outlines the approach for the verification of the effectiveness and efficiency of this system. Specifically, the justification is a multi-step approach. It involves the deployment of integral codes, lumped parameter containment codes and CFD codes and the use of the sigma criterion, which provides the link to the broad experimental data base for flame acceleration (FA) and deflagration to detonation transition (DDT). The procedure is illustrated with an example. The performed analyses show that hydrogen combustion at any time does not lead to pressure or temperature loads that threaten the containment integrity of the EPR. (authors)

Characterization of potassium bromide crystals grown in the aqueous solution of picric acid

Energy Technology Data Exchange (ETDEWEB)

Maheswari, J. Uma, E-mail: umak.anand@gmail.com [Department of Physics, The M.D.T.Hindu College, Tirunelveli 627010, Tamilnadu (India); Krishnan, C. [Department of Physics, Arignar Anna College, Aralvoymoli 629301, Tamilnadu (India); Kalyanaraman, S. [Physics Research Centre, Sri Paramakalyani College, Alwarkurichi 627412, Tamilnadu (India); Selvarajan, P. [Department of Physics, Aditanar College of Arts and Science, Tiruchendur 628216, Tamilnadu (India)

2016-12-01

Potassium bromide crystals were grown in the aqueous solution of picric acid by slow evaporation technique at room temperature. X-ray Diffraction (XRD) analysis ensures that the grown sample is in Fm3m space group and FCC structure. Energy Dispersive X-ray Spectroscopy (EDX) reveals the presence of elements in the title compound. UV–Vis-NIR spectrum reveals that the grown sample is a promising nonlinear optical (NLO) material. FTIR analysis confirms the functional groups present in the sample. The thermogravimetric (TG) and differential thermogravimetric (DTA) analyses ensure that the sample material is thermally stable up to 160 °C. The second harmonic efficiency of the sample is 1.3 times greater than that of standard KDP. The mechanical strength of the grown sample is estimated by Vickers microhardness tester. The electrical properties were investigated by impedance analysis and the results of various studies of the grown crystals are discussed.

Thermal analyses. Information on the expected baking process; Thermische analyses. Informatie over een te verwachten bakgedrag

Energy Technology Data Exchange (ETDEWEB)

Van Wijck, H. [Stichting Technisch Centrum voor de Keramische Industrie TCKI, Velp (Netherlands)

2009-09-01

The design process and the drying process for architectural ceramics and pottery partly determine the characteristics of the final product, but the largest changes occur during the baking process. An overview is provided of the different thermal analyses and how the information from these analyses can predict the process in practice. (mk) [Dutch] Het vormgevingsproces en het droogproces voor bouwkeramische producten en aardewerk bepalen voor een deel de eigenschappen van de eindproducten, maar de grootste veranderingen treden op bij het bakproces. Een overzicht wordt gegeven van de verschillende thermische analyses en hoe de informatie uit deze analyses het in de praktijk te verwachten gedrag kan voorspellen.

Contesting Citizenship: Comparative Analyses

DEFF Research Database (Denmark)

Siim, Birte; Squires, Judith

2007-01-01

importance of particularized experiences and multiple ineequality agendas). These developments shape the way citizenship is both practiced and analysed. Mapping neat citizenship modles onto distinct nation-states and evaluating these in relation to formal equality is no longer an adequate approach....... Comparative citizenship analyses need to be considered in relation to multipleinequalities and their intersections and to multiple governance and trans-national organisinf. This, in turn, suggests that comparative citizenship analysis needs to consider new spaces in which struggles for equal citizenship occur...

Status on DEMO Helium Cooled Lithium Lead breeding blanket thermo-mechanical analyses

Energy Technology Data Exchange (ETDEWEB)

Aubert, J., E-mail: julien.aubert@cea.fr [CEA-Saclay, DEN, DM2S, F-91191 Gif-sur-Yvette (France); Aiello, G.; Jaboulay, J.-C. [CEA-Saclay, DEN, DM2S, F-91191 Gif-sur-Yvette (France); Kiss, B. [Institute of Nuclear Techniques, Budapest University of Technology and Economics, Budapest (Hungary); Morin, A. [CEA-Saclay, DEN, DM2S, F-91191 Gif-sur-Yvette (France)

2016-11-01

Highlights: • CEA with the support of Wigner-RCP and IPP-CR, is in charge of the design of the HCLL blanket for DEMO. The DEMO HCLL breeding blanket design capitalizes on the experience acquired on the HCLL Test Blanket Module designed for ITER. Design improvements are being implemented to adapt the design to DEMO specifications and performance objectives. • Thermal and mechanical analyses have been carried out in order to justify the design of the HCLL breeding blanket showing promising results for tie rods modules’ attachments system and relatively good behavior of the box in case of LOCA when comparing to RCC-MRx criteria. • CFD thermal analyses on generic breeding unit have enabled the consolidation of the results obtained with previous FEM design analyses. - Abstract: The EUROfusion Consortium develops a design of a fusion power demonstrator (DEMO) in the framework of the European “Horizon 2020” innovation and research program. One of the key components in the fusion reactor is the breeding blanket surrounding the plasma, ensuring tritium self-sufficiency, heat removal for conversion into electricity, and neutron shielding. The Helium Cooled Lithium Lead (HCLL) blanket is one of the concepts which is investigated for DEMO. It is made of a Eurofer structure and uses the eutectic liquid lithium–lead as tritium breeder and neutron multiplier, and helium gas as coolant. Within the EUROfusion organization, CEA with the support of Wigner-RCP and IPP-CR, is in charge of the design of the HCLL blanket for DEMO. This paper presents the status of the thermal and mechanical analyses carried out on the HCLL breeding blanket in order to justify the design. CFD thermal analyses on generic breeding unit including stiffening plates and cooling plates have been performed with ANSYS in order to consolidate results obtained with previous FEM design analyses. Moreover in order to expand the justification of the HCLL Breeding blanket design, the most loaded area of

Research on pyrolysis characteristics and kinetics of super fine and conventional pulverized coal

International Nuclear Information System (INIS)

Zhang Chaoqun; Jiang Xiumin; Wei Lihong; Wang Hui

2007-01-01

Based on isothermal thermogravimetric analysis (TGA) and kinetic equations, the optimization toolbox of MATLAB was applied to study the effects of particle size and heating rate on the pyrolysis characteristics and kinetics and to obtain the mechanism function and kinetic parameters of Yuanbaoshan coal at four different particle sizes and heating rates. The pyrolysis characteristics of the samples were analyzed using thermogravimetric (TG) curves and differential thermogravimetric (DTG) curves. The results show that the coal pyrolysis process is strongly affected by heating rate and particle size. As the heating rate increases, the temperature of volatile matter initiation increases, the total volatile matter evolved decreases and the DTG peak shifts toward higher temperature. As the particle size decreases, the temperature of volatile matter initiation of the coal sample decreases and the maximum rate of mass loss increases. In the pyrolysis of coal, the activation energies of the samples were found to increase with growing particle size and decreasing heating rate for both of the devolatilization temperature stages. In the lower temperature stage, the coal samples show a great difference in mechanism function at different particle sizes and heating rates

Association between Adult Height and Risk of Colorectal, Lung, and Prostate Cancer: Results from Meta-analyses of Prospective Studies and Mendelian Randomization Analyses

Science.gov (United States)

Khankari, Nikhil K.; Shu, Xiao-Ou; Wen, Wanqing; Kraft, Peter; Lindström, Sara; Peters, Ulrike; Schildkraut, Joellen; Schumacher, Fredrick; Bofetta, Paolo; Risch, Angela; Bickeböller, Heike; Amos, Christopher I.; Easton, Douglas; Gruber, Stephen B.; Haiman, Christopher A.; Hunter, David J.; Chanock, Stephen J.; Pierce, Brandon L.; Zheng, Wei

2016-01-01

Background Observational studies examining associations between adult height and risk of colorectal, prostate, and lung cancers have generated mixed results. We conducted meta-analyses using data from prospective cohort studies and further carried out Mendelian randomization analyses, using height-associated genetic variants identified in a genome-wide association study (GWAS), to evaluate the association of adult height with these cancers. Methods and Findings A systematic review of prospective studies was conducted using the PubMed, Embase, and Web of Science databases. Using meta-analyses, results obtained from 62 studies were summarized for the association of a 10-cm increase in height with cancer risk. Mendelian randomization analyses were conducted using summary statistics obtained for 423 genetic variants identified from a recent GWAS of adult height and from a cancer genetics consortium study of multiple cancers that included 47,800 cases and 81,353 controls. For a 10-cm increase in height, the summary relative risks derived from the meta-analyses of prospective studies were 1.12 (95% CI 1.10, 1.15), 1.07 (95% CI 1.05, 1.10), and 1.06 (95% CI 1.02, 1.11) for colorectal, prostate, and lung cancers, respectively. Mendelian randomization analyses showed increased risks of colorectal (odds ratio [OR] = 1.58, 95% CI 1.14, 2.18) and lung cancer (OR = 1.10, 95% CI 1.00, 1.22) associated with each 10-cm increase in genetically predicted height. No association was observed for prostate cancer (OR = 1.03, 95% CI 0.92, 1.15). Our meta-analysis was limited to published studies. The sample size for the Mendelian randomization analysis of colorectal cancer was relatively small, thus affecting the precision of the point estimate. Conclusions Our study provides evidence for a potential causal association of adult height with the risk of colorectal and lung cancers and suggests that certain genetic factors and biological pathways affecting adult height may also affect the

Combining Conversation Analysis and Nexus Analysis to analyse sociomaterial and affective practices

DEFF Research Database (Denmark)

Raudaskoski, Pirkko Liisa

2016-01-01

of resemiotization (Iedema 2000). Within organization and design studies, materiality has become a focus in the increasingly popular sociomaterial approach to everyday practices (e.g. Orlikowski 2007). Some sociomaterial scholars (e.g. Sørensen 2013) analyse ethnographic data either as evidence for the sociomaterial....... The analytical effort is to get to the senses and sensations which are regarded as opposite of sense-making. In my presentation, I go through some of my own analyses from various institutional interactions to show how CA-based multimodal analyses of local interactional (or intra-actional) trajectories combined...... configuration, also as an interdisciplinary offer for an analytic package that might help sociomaterial researchers of practices come even closer to the situation at hand as an assemblage out of which materials, humans and experiences emerge....

Shotgun pyrosequencing metagenomic analyses of dusts from swine confinement and grain facilities.

Science.gov (United States)

Boissy, Robert J; Romberger, Debra J; Roughead, William A; Weissenburger-Moser, Lisa; Poole, Jill A; LeVan, Tricia D

2014-01-01

Inhalation of agricultural dusts causes inflammatory reactions and symptoms such as headache, fever, and malaise, which can progress to chronic airway inflammation and associated diseases, e.g. asthma, chronic bronchitis, chronic obstructive pulmonary disease, and hypersensitivity pneumonitis. Although in many agricultural environments feed particles are the major constituent of these dusts, the inflammatory responses that they provoke are likely attributable to particle-associated bacteria, archaebacteria, fungi, and viruses. In this study, we performed shotgun pyrosequencing metagenomic analyses of DNA from dusts from swine confinement facilities or grain elevators, with comparisons to dusts from pet-free households. DNA sequence alignment showed that 19% or 62% of shotgun pyrosequencing metagenomic DNA sequence reads from swine facility or household dusts, respectively, were of swine or human origin, respectively. In contrast only 2% of such reads from grain elevator dust were of mammalian origin. These metagenomic shotgun reads of mammalian origin were excluded from our analyses of agricultural dust microbiota. The ten most prevalent bacterial taxa identified in swine facility compared to grain elevator or household dust were comprised of 75%, 16%, and 42% gram-positive organisms, respectively. Four of the top five swine facility dust genera were assignable (Clostridium, Lactobacillus, Ruminococcus, and Eubacterium, ranging from 4% to 19% relative abundance). The relative abundances of these four genera were lower in dust from grain elevators or pet-free households. These analyses also highlighted the predominance in swine facility dust of Firmicutes (70%) at the phylum level, Clostridia (44%) at the Class level, and Clostridiales at the Order level (41%). In summary, shotgun pyrosequencing metagenomic analyses of agricultural dusts show that they differ qualitatively and quantitatively at the level of microbial taxa present, and that the bioinformatic analyses

Shotgun pyrosequencing metagenomic analyses of dusts from swine confinement and grain facilities.

Directory of Open Access Journals (Sweden)

Robert J Boissy

Full Text Available Inhalation of agricultural dusts causes inflammatory reactions and symptoms such as headache, fever, and malaise, which can progress to chronic airway inflammation and associated diseases, e.g. asthma, chronic bronchitis, chronic obstructive pulmonary disease, and hypersensitivity pneumonitis. Although in many agricultural environments feed particles are the major constituent of these dusts, the inflammatory responses that they provoke are likely attributable to particle-associated bacteria, archaebacteria, fungi, and viruses. In this study, we performed shotgun pyrosequencing metagenomic analyses of DNA from dusts from swine confinement facilities or grain elevators, with comparisons to dusts from pet-free households. DNA sequence alignment showed that 19% or 62% of shotgun pyrosequencing metagenomic DNA sequence reads from swine facility or household dusts, respectively, were of swine or human origin, respectively. In contrast only 2% of such reads from grain elevator dust were of mammalian origin. These metagenomic shotgun reads of mammalian origin were excluded from our analyses of agricultural dust microbiota. The ten most prevalent bacterial taxa identified in swine facility compared to grain elevator or household dust were comprised of 75%, 16%, and 42% gram-positive organisms, respectively. Four of the top five swine facility dust genera were assignable (Clostridium, Lactobacillus, Ruminococcus, and Eubacterium, ranging from 4% to 19% relative abundance. The relative abundances of these four genera were lower in dust from grain elevators or pet-free households. These analyses also highlighted the predominance in swine facility dust of Firmicutes (70% at the phylum level, Clostridia (44% at the Class level, and Clostridiales at the Order level (41%. In summary, shotgun pyrosequencing metagenomic analyses of agricultural dusts show that they differ qualitatively and quantitatively at the level of microbial taxa present, and that the

Nanostructure and thermal properties of melt compounded PE/clay nanocomposites filled with an organosilylated montmorillonite

Energy Technology Data Exchange (ETDEWEB)

Scarfato, Paola, E-mail: pscarfato@unisa.it [Department of Industrial Engineering, University of Salerno Via Giovanni Paolo II 132 – 84084 Fisciano (Italy); BAM - Federal Institute for Materials Research and Testing, 7.5 Technical Properties of Polymeric Materials, Unter den Eichen 87 - 12205 Berlin (Germany); Incarnato, Loredana; Di Maio, Luciano [Department of Industrial Engineering, University of Salerno Via Giovanni Paolo II 132 – 84084 Fisciano (Italy); Dittrich, Bettina; Niebergall, Ute; Böhning, Martin; Schartel, Bernhard [BAM - Federal Institute for Materials Research and Testing, 7.5 Technical Properties of Polymeric Materials, Unter den Eichen 87 - 12205 Berlin (Germany)

2015-12-17

In this work we report on the functionalization of a natural sodium montmorillonite (MMT) with (3-glycidyloxypropyl)trimethoxysilane by a silylation procedure and on its use as nanofiller in melt compounding of polyethylene nanocomposites. The obtained organosilylated clay showed higher interlayer spacing than the original MMT and higher thermal stability with respect to most of commercial organoclays modified with alkylammonium salts. Its addition (at 5wt%) to two different polyethylene matrices (a low density polyethylene, LDPE, and a high density polyethylene, HDPE), processed in a pilot-scale twin-screw extruder, allowed to produce hybrids with nanoscale dispersion of the filler, as demonstrated by X-ray diffraction. Thermogravimetric and differential scanning thermal analyses point out that the obtained nanocomposites do not show noticeable changes in the thermal behavior of both LDPE and HDPE, even if a slight reduction in the overall bulk crystallinity was observed in presence of the nanofillers.

Nanostructure and thermal properties of melt compounded PE/clay nanocomposites filled with an organosilylated montmorillonite

International Nuclear Information System (INIS)

Scarfato, Paola; Incarnato, Loredana; Di Maio, Luciano; Dittrich, Bettina; Niebergall, Ute; Böhning, Martin; Schartel, Bernhard

2015-01-01

In this work we report on the functionalization of a natural sodium montmorillonite (MMT) with (3-glycidyloxypropyl)trimethoxysilane by a silylation procedure and on its use as nanofiller in melt compounding of polyethylene nanocomposites. The obtained organosilylated clay showed higher interlayer spacing than the original MMT and higher thermal stability with respect to most of commercial organoclays modified with alkylammonium salts. Its addition (at 5wt%) to two different polyethylene matrices (a low density polyethylene, LDPE, and a high density polyethylene, HDPE), processed in a pilot-scale twin-screw extruder, allowed to produce hybrids with nanoscale dispersion of the filler, as demonstrated by X-ray diffraction. Thermogravimetric and differential scanning thermal analyses point out that the obtained nanocomposites do not show noticeable changes in the thermal behavior of both LDPE and HDPE, even if a slight reduction in the overall bulk crystallinity was observed in presence of the nanofillers

U3O8 microspheres sintering kinetics

International Nuclear Information System (INIS)

Godoy, A.L.E.

1986-01-01

U 3 O 8 microspheres sintering kinetics was determined using a hot-stage optical microscopy apparatus, able to reach temperature up to 1350 0 C in controlled atmospheres. The sintered material had its microstructure analysed by optical and electron microscopy. The microspheres were characterized initialy utilizing X-ray diffractometry and thermogravimetry. The equation which describes the microspheres shrinkage in function of the time was obtained using finite difference analysis X-ray diffractometry indicated hexagonal structure for the microspheres main starting material, ammonium diuranate thermogravimetric analysis showed reduction of this material to U 3 O 8 at 600 0 C. Ceramography results showed 5 hours sintered microspheres grain sizes G vary with the temperature. Sintered U 3 O 8 micrographs compared with published results for UO 2 , indicate similar homogeneity microstructural characteristics and suggest the processed micorspheres to be potentially useful as nuclear fuels. (Author) [pt

Five Kepler target stars that show multiple transiting exoplanet candidates

Energy Technology Data Exchange (ETDEWEB)

Steffen, Jason H.; /Fermilab; Batalha, Natalie M.; /San Jose State U.; Borucki, William J.; /NASA, Ames; Buchhave, Lars A.; /Harvard-Smithsonian Ctr. Astrophys. /Bohr Inst.; Caldwell, Douglas A.; /NASA, Ames /SETI Inst., Mtn. View; Cochran, William D.; /Texas U.; Endl, Michael; /Texas U.; Fabrycky, Daniel C.; /Harvard-Smithsonian Ctr. Astrophys.; Fressin, Francois; /Harvard-Smithsonian Ctr. Astrophys.; Ford, Eric B.; /Florida U.; Fortney, Jonathan J.; /UC, Santa Cruz, Phys. Dept. /NASA, Ames

2010-06-01

We present and discuss five candidate exoplanetary systems identified with the Kepler spacecraft. These five systems show transits from multiple exoplanet candidates. Should these objects prove to be planetary in nature, then these five systems open new opportunities for the field of exoplanets and provide new insights into the formation and dynamical evolution of planetary systems. We discuss the methods used to identify multiple transiting objects from the Kepler photometry as well as the false-positive rejection methods that have been applied to these data. One system shows transits from three distinct objects while the remaining four systems show transits from two objects. Three systems have planet candidates that are near mean motion commensurabilities - two near 2:1 and one just outside 5:2. We discuss the implications that multitransiting systems have on the distribution of orbital inclinations in planetary systems, and hence their dynamical histories; as well as their likely masses and chemical compositions. A Monte Carlo study indicates that, with additional data, most of these systems should exhibit detectable transit timing variations (TTV) due to gravitational interactions - though none are apparent in these data. We also discuss new challenges that arise in TTV analyses due to the presence of more than two planets in a system.

Pyrolysis and thermal oxidation kinetics of sugar mill press mud

International Nuclear Information System (INIS)

Gangavati, P.B.; Safi, M.J.; Singh, A.; Prasad, B.; Mishra, I.M.

2005-01-01

Press mud, a solid waste obtained from the sugar mills, has the potential of energy generation through pyrolysis and gasification. The paper reports its proximate and ultimate analyses, deformation and fusion ash temperatures, lower and higher heating values, physico-chemical and thermal degradation in nitrogen and air atmospheres. The thermal degradation was conducted in a thermogravimetric analyzer from room temperature to 900 deg C at heating rates of 20 and 40 K min -1 . The thermogravimetric, derivative thermogravimetric and differential thermal analyses were carried out to determine the rate of volatiles evolution, the effect of heating rates on the thermal degradation characteristics and to determine the global mass loss kinetics of thermal degradation. The thermal degradation was found to occur in several distinct phases: each phase giving volatile evolution in an independent parallel lump. Each decomposition phase was modeled by a single irreversible reaction with respect to the solid mass. Global mass loss kinetics was also determined for the entire decomposition process, as if occurring in one single step. The integral and differential techniques were used for the determination of kinetic parameters. Using the method of Agrawal and Sivasubramanian [R.K. Agrawal, M.S. Sivasubramanian, AIChE J. 33 (1987) 7] for the total degradation zone, the orders of reaction were found in the range of 1.00-2.50 in both the atmospheres (i.e. nitrogen and air) and the activation energy in the range of 27.84-33.44 and 57.41-88.92 kJ mol -1 in nitrogen and air, respectively. The pre-exponential factor was found in the range of 32.1-95.1 and 5.10 x 10 4 to 5.46 x 10 9 min -1 in nitrogen and air atmospheres, respectively

Severe accident recriticality analyses (SARA)

DEFF Research Database (Denmark)

Frid, W.; Højerup, C.F.; Lindholm, I.

2001-01-01

with all three codes. The core initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality-both super-prompt power bursts and quasi steady-state power......Recriticality in a BWR during reflooding of an overheated partly degraded core, i.e. with relocated control rods, has been studied for a total loss of electric power accident scenario. In order to assess the impact of recriticality on reactor safety, including accident management strategies......, which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal g(-1), was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding rate of 2000 kg s(-1). In most cases, however, the predicted energy deposition was smaller, below...

45-day safety screen results and final report for tank 241-C-202, auger samples 95-Aug-026 and 95-Aug-027

International Nuclear Information System (INIS)

Baldwin, J.H.

1995-01-01

Two auger samples from tank 241-C-202 (C-202) were received at the 222-S Laboratories and underwent safety screening analysis, consisting of differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and total alpha activity. Two samples were submitted for energetics determination by DSC. Within the triplicate analyses of each sample, one of the results for energetics exceeded the notification limit. The sample and duplicate analyses for both augers exceeded the notification limit for TGA. As required by the Tank Characterization Plan, the appropriate notifications were made within 24 hours of official confirmation that the limits were violated

Assembly of new polyoxometalate–templated metal–organic frameworks based on flexible ligands

Energy Technology Data Exchange (ETDEWEB)

Li, Na; Mu, Bao; Lv, Lei; Huang, Rudan, E-mail: huangrd@bit.edu.cn

2015-03-15

Four new polyoxometalate(POM)–templated metal–organic frameworks based on flexible ligands, namely, [Cu{sub 6}(bip){sub 12}(PMo{sup VI}{sub 12}O{sub 40}){sub 2}(PMo{sup V}Mo{sup VI}{sub 11}O{sub 40}O{sub 2})]·8H{sub 2}O(1), [Cu{sup I}{sub 3}Cu{sup II}{sub 3}(bip){sub 12}(PMo{sup VI}{sub 12}O{sub 40}){sub 2}(PMo{sup V}{sub 12}O{sub 34})]·8H{sub 2}O(2), [Ni{sub 6}(bip){sub 12}(PMo{sup VI}{sub 12}O{sub 40})(PMo{sup VI}{sub 11}Mo{sup V}O{sub 40}){sub 2}]Cl·6H{sub 2}O(3), [Co{sup II}{sub 3}Co{sup III}{sub 2}(H{sub 2}bib){sub 2}(Hbib){sub 2}(PW{sub 9}O{sub 34}){sub 2}(H{sub 2}O){sub 6}]·6H{sub 2}O(4) (bip=1,3-bis(imidazolyl)propane, bib=1,4-bis(imidazolyl)butane) have been obtained under hydrothermal condition and characterized by single-crystal X-ray diffraction analyses, elemental analyses, and thermogravimetric (TG) analyses. The studies of single crystal X-ray indicate that compounds 1–3 crystallize in the trigonal space group P-3, and compound 4 crystallizes in the triclinic space group P-1. Compounds 1 and 3 represent 3D frameworks, and POMs as the guest molecules are incorporated into the cages which are composed of the ligands and metals, while compounds 2 and 4 show 3D frameworks by hydrogen bonds. This compounds provide new examples of host–guest compounds based on flexible bis(imidazole) ligands. In addition, the electrochemical property and the catalytic property of compound 1 have also been investigated. - Graphical abstract: Four inorganic–organic hybrid compounds based polyoxometalates (POMs) and flexible ligands, namely, have been obtained under hydrothermal conditions and characterized by single-crystal X-ray diffraction analyses, elemental analyses, IR spectra, and thermogravimetric (TG) analyses. Compounds 1–3 are new examples of host–guest compounds based on flexible bis(imidazole) ligands and POMs as the guest molecules are incorporated into the cages which are composed of the ligands and metals. - Highlights: • Polyoxometalate�

Identifying null meta-analyses that are ripe for updating

Directory of Open Access Journals (Sweden)

Fang Manchun

2003-07-01

Full Text Available Abstract Background As an increasingly large number of meta-analyses are published, quantitative methods are needed to help clinicians and systematic review teams determine when meta-analyses are not up to date. Methods We propose new methods for determining when non-significant meta-analytic results might be overturned, based on a prediction of the number of participants required in new studies. To guide decision making, we introduce the "new participant ratio", the ratio of the actual number of participants in new studies to the predicted number required to obtain statistical significance. A simulation study was conducted to study the performance of our methods and a real meta-analysis provides further evidence. Results In our three simulation configurations, our diagnostic test for determining whether a meta-analysis is out of date had sensitivity of 55%, 62%, and 49% with corresponding specificity of 85%, 80%, and 90% respectively. Conclusions Simulations suggest that our methods are able to detect out-of-date meta-analyses. These quick and approximate methods show promise for use by systematic review teams to help decide whether to commit the considerable resources required to update a meta-analysis. Further investigation and evaluation of the methods is required before they can be recommended for general use.

Meta-analyses of HFE variants in coronary heart disease.

Science.gov (United States)

Lian, Jiangfang; Xu, Limin; Huang, Yi; Le, Yanping; Jiang, Danjie; Yang, Xi; Xu, Weifeng; Huang, Xiaoyan; Dong, Changzheng; Ye, Meng; Zhou, Jianqing; Duan, Shiwei

2013-09-15

HFE gene variants can cause hereditary hemochromatosis (HH) that often comes along with an increased risk of coronary heart disease (CHD). The goal of our study is to assess the contribution of four HFE gene variants to the risk of CHD. We conducted four meta-analyses of the studies examining the association between four HFE gene variants and the risk of CHD. A systematic search was conducted using MEDLINE, EMBASE, Web of Science and China National Knowledge Infrastructure (CNKI), Wanfang Chinese Periodical. Meta-analyses showed that HFE rs1799945-G allele was associated with a 6% increased risk of CHD (P=0.02, odds ratio (OR)=1.06, 95% confidence interval (CI)=1.01-1.11). However, no association between the other three HFE gene variants (rs1800562, rs1800730, and rs9366637) and CHD risk was observed by the meta-analyses (all P values>0.05). In addition, the results of our case-control study indicated that rs1800562 and rs1800730 were monomorphic, and that rs1799945 and rs9366637 were not associated with CHD in Han Chinese. Our meta-analysis suggested that a significant association existed between rs1799945 mutation and CHD, although this mutation was rare in Han Chinese. Copyright © 2013 Elsevier B.V. All rights reserved.

Consensuses and discrepancies of basin-scale ocean heat content changes in different ocean analyses

Science.gov (United States)

Wang, Gongjie; Cheng, Lijing; Abraham, John; Li, Chongyin

2018-04-01

Inconsistent global/basin ocean heat content (OHC) changes were found in different ocean subsurface temperature analyses, especially in recent studies related to the slowdown in global surface temperature rise. This finding challenges the reliability of the ocean subsurface temperature analyses and motivates a more comprehensive inter-comparison between the analyses. Here we compare the OHC changes in three ocean analyses (Ishii, EN4 and IAP) to investigate the uncertainty in OHC in four major ocean basins from decadal to multi-decadal scales. First, all products show an increase of OHC since 1970 in each ocean basin revealing a robust warming, although the warming rates are not identical. The geographical patterns, the key modes and the vertical structure of OHC changes are consistent among the three datasets, implying that the main OHC variabilities can be robustly represented. However, large discrepancies are found in the percentage of basinal ocean heating related to the global ocean, with the largest differences in the Pacific and Southern Ocean. Meanwhile, we find a large discrepancy of ocean heat storage in different layers, especially within 300-700 m in the Pacific and Southern Oceans. Furthermore, the near surface analysis of Ishii and IAP are consistent with sea surface temperature (SST) products, but EN4 is found to underestimate the long-term trend. Compared with ocean heat storage derived from the atmospheric budget equation, all products show consistent seasonal cycles of OHC in the upper 1500 m especially during 2008 to 2012. Overall, our analyses further the understanding of the observed OHC variations, and we recommend a careful quantification of errors in the ocean analyses.

Elastodynamic fracture analyses of large crack-arrest experiments

International Nuclear Information System (INIS)

Bass, B.R.; Pugh, C.E.; Walker, J.K.

1985-01-01

Results obtained to date show that the essence of the run-arrest events, including dynamic behavior, is being modeled. Refined meshes and optimum solution algorithms are important parameters in elastodynamic analysis programs to give sufficient resolution to the geometric and time-dependent aspects of fracture analyses. Further refinements in quantitative representation of material parameters and the inclusion of rate dependence through viscoplastic modeling is expected to give an even more accurate basis for assessing the fracture behavior of reactor pressure vessels under PTS and other off-normal loading conditions

ATHENA/INTRA analyses for ITER, NSSR-2

International Nuclear Information System (INIS)

Shen, Kecheng; Eriksson, John; Sjoeberg, A.

1999-02-01

The present report is a summary report including thermal-hydraulic analyses made at Studsvik Eco and Safety AB for the ITER NSSR-2 safety documentation. The objective of the analyses was to reveal the safety characteristics of various heat transfer systems at specified operating conditions and to indicate the conditions for which there were obvious risks of jeopardising the structural integrity of the coolant systems. In the latter case also some analyses were made to indicate conceivable mitigating measures for maintaining the integrity.The analyses were primarily concerned with the First Wall and Divertor heat transfer systems. Several enveloping transients were analysed with associated specific flow and heat load boundary conditions. The analyses were performed with the ATHENA and INTRA codes

ATHENA/INTRA analyses for ITER, NSSR-2

Energy Technology Data Exchange (ETDEWEB)

Shen, Kecheng; Eriksson, John; Sjoeberg, A

1999-02-01

The present report is a summary report including thermal-hydraulic analyses made at Studsvik Eco and Safety AB for the ITER NSSR-2 safety documentation. The objective of the analyses was to reveal the safety characteristics of various heat transfer systems at specified operating conditions and to indicate the conditions for which there were obvious risks of jeopardising the structural integrity of the coolant systems. In the latter case also some analyses were made to indicate conceivable mitigating measures for maintaining the integrity.The analyses were primarily concerned with the First Wall and Divertor heat transfer systems. Several enveloping transients were analysed with associated specific flow and heat load boundary conditions. The analyses were performed with the ATHENA and INTRA codes 8 refs, 14 figs, 15 tabs

Mechanical, Rheological and Thermal Properties of Polystyrene/1-Octadecanol Modified Carbon Nanotubes Nanocomposites

KAUST Repository

Amr, Issam Thaher

2014-09-04

The results of the studies on the functionalization of multi-walled carbon nanotubes (MWCNT) with 1-octadecanol and its usage as reinforcing filler in the bulk polymerization of styrene are reported in this article. Both unmodified and modified CNTs were utilized in different loadings, however, without any initiator. The resulting composites were characterized by using mechanical testing, differential scanning calorimetry, thermogravimetric analysis and melt rheology. The tensile tests show the addition of 0.5wt% of CNT-C18 results in 19.5% increment of Young\\'s modulus. The DSC study shows a decrease in T-g values of prepared PS/CNT nanocomposite. The rheological study was conducted at 190 degrees C and shows that addition of pure CNT increased the viscoelastic behavior of the PS matrices, while the CNT-C18 act as plasticizer. Thermogravimetric analysis shows that the incorporation of CNT into PS enhanced the thermal properties significantly.

Embodied energy and emergy analyses of a concentrating solar power (CSP) system

International Nuclear Information System (INIS)

Zhang Meimei; Wang Zhifeng; Xu Chao; Jiang Hui

2012-01-01

Although concentrating solar power (CSP) technology has been projected as one of the most promising candidates to replace conventional power plants burning fossil fuels, the potential advantages and disadvantages of the CSP technology have not been thoroughly evaluated. To better understand the performance of the CSP technology, this paper presents an ecological accounting framework based on embodied energy and emergy analyses methods. The analyses are performed for the 1.5 MW Dahan solar tower power plant in Beijing, China and different evaluation indices used in the embodied energy and emergy analyses are employed to evaluate the plant performance. Our analysis of the CSP plant are compared with six Italian power plants with different energy sources and an American PV plant, which demonstrates the CSP is the superior technology. - Highlights: ► Embodied energy and emergy analyses are employed to evaluate the first solar tower power plant in China. ► Different evaluation indices are quantitatively analyzed to show the advantages of CSP technology. ► This analysis provides insights for making energy policy and investment decisions about CSP technology.

Synthesis and characterization of chromium doped boehmite nanofibres

International Nuclear Information System (INIS)

Yang Jing; Frost, Ray L.; Yuan Yong

2009-01-01

Thermogravimetric and differential thermogravimetric analysis has been used to study synthesised chromium doped boehmite. The dehydroxylation temperature increases significantly from 0 to 5% doping, after which the dehydroxylation temperature shows a small steady increase up to the 20% doping level. The temperature of dehydroxylation increases with time of hydrothermal treatment. Chromium doped boehmite nanofibres were also characterised by X-ray diffraction and transmission electron microscopy. Hydrothermal treatment of doped boehmite with chromium resulted in the formation of nanofibres over a wide dopant range. Nanofibres up to 500 nm in length and between 4 and 6 nm in width were produced

Synthesis of a Biglucoside and Its Application as Montmorillonite Hydration Inhibitor

Directory of Open Access Journals (Sweden)

Xin-chun Zhang

2014-01-01

Full Text Available A biglucoside (BG was synthesized with glucose and epichlorohydrin as raw materials. The inhibition of BG against montmorillonite swelling was investigated by various methods including montmorillonite linear expansion test, mud ball immersing test, thermogravimetric analysis, and scanning electron microscopy. The results show that the BG has good inhibition ability to the hydration swelling and dispersion of montmorillonite. Under the same condition, the linear expansion ratio of montmorillonite in BG solution is much lower than that of MEG. The particle distribution measurement, thermogravimetric analysis, FT-IR, and scanning electron microscopy results all prove the efficient inhibition of BG.

Indian Point 2 steam generator tube rupture analyses

International Nuclear Information System (INIS)

Dayan, A.

1985-01-01

Analyses were conducted with RETRAN-02 to study consequences of steam generator tube rupture (SGTR) events. The Indian Point, Unit 2, power plant (IP2, PWR) was modeled as a two asymmetric loops, consisting of 27 volumes and 37 junctions. The break section was modeled once, conservatively, as a 150% flow area opening at the wall of the steam generator cold leg plenum, and once as a 200% double-ended tube break. Results revealed 60% overprediction of breakflow rates by the traditional conservative model. Two SGTR transients were studied, one with low-pressure reactor trip and one with an earlier reactor trip via over temperature ΔT. The former is more typical to a plant with low reactor average temperature such as IP2. Transient analyses for a single tube break event over 500 seconds indicated continued primary subcooling and no need for steam line pressure relief. In addition, SGTR transients with reactor trip while the pressurizer still contains water were found to favorably reduce depressurization rates. Comparison of the conservative results with independent LOFTRAN predictions showed good agreement

Herbarium specimens show contrasting phenological responses to Himalayan climate.

Science.gov (United States)

Hart, Robbie; Salick, Jan; Ranjitkar, Sailesh; Xu, Jianchu

2014-07-22

Responses by flowering plants to climate change are complex and only beginning to be understood. Through analyses of 10,295 herbarium specimens of Himalayan Rhododendron collected by plant hunters and botanists since 1884, we were able to separate these responses into significant components. We found a lack of directional change in mean flowering time over the past 45 y of rapid warming. However, over the full 125 y of collections, mean flowering time shows a significant response to year-to-year changes in temperature, and this response varies with season of warming. Mean flowering advances with annual warming (2.27 d earlier per 1 °C warming), and also is delayed with fall warming (2.54 d later per 1 °C warming). Annual warming may advance flowering through positive effects on overwintering bud formation, whereas fall warming may delay flowering through an impact on chilling requirements. The lack of a directional response suggests that contrasting phenological responses to temperature changes may obscure temperature sensitivity in plants. By drawing on large collections from multiple herbaria, made over more than a century, we show how these data may inform studies even of remote localities, and we highlight the increasing value of these and other natural history collections in understanding long-term change.

Physiological and enzymatic analyses of pineapple subjected to ionizing radiation

International Nuclear Information System (INIS)

Silva, Josenilda Maria da; Silva, Juliana Pizarro; Spoto, Marta Helena Fillet

2007-01-01

The physiological and enzymatic post-harvest characteristics of the pineapple cultivar Smooth Cayenne were evaluated after the fruits were gamma-irradiated with doses of 100 and 150 Gy and the fruits were stored for 10, 20 and 30 days at 12 deg C (±1) and relative humidity of 85% (±5). Physiological and enzymatic analyses were made for each storage period to evaluate the alterations resulting from the application of ionizing radiation. Control specimens showed higher values of soluble pectins, total pectins, reducing sugars, sucrose and total sugars and lower values of polyphenyloxidase and polygalacturonase enzyme activities. All the analyses indicated that storage time is a significantly influencing factor. The 100 Gy dosage and 20-day storage period presented the best results from the standpoint of maturation and conservation of the fruits quality. (author)

Multielemental analyses of tree rings by inductively coupled plasma mass spectrometry

International Nuclear Information System (INIS)

Hall, G.S.

1990-01-01

Inductively coupled plasma mass spectrometry (ICP-MS) was evaluated for major, minor, trace, and ultra-trace elemental analyses of individual tree rings. The samples were obtained from an old-growth Douglas fir growing near Mount St. Helens volcano, and from trees at various other North American sites. Eightly percent of elements from Li to U had detection limits in the solid (wood) below 8.0 ng g -1 . Two anomalous peaks occur in Mount St. Helens samples at A.D. 1478 and 1490 that closely correlate with past eruptions of the volcano. These results show that ICP-MS is a rapid and sensitive analytical method for multielemental analyses of individual tree rings. (author) 16 refs.; 2 figs.; 2 tabs

Thermoelastic analyses of spent fuel repositories in bedded and dome salt. Technical memorandum report RSI-0054

International Nuclear Information System (INIS)

Callahan, G.D.; Ratigan, J.L.

1978-01-01

Global thermoelastic analyses of bedded and dome salt models showed a slight preference for the bedded salt model through the range of thermal loading conditions. Spent fuel thermal loadings should be less than 75 kW/acre of the repository pending more accurate material modeling. One should first limit the study to one or two spent fuel thermal loading (i.e. 75 kW/acre and/or 50 kW/acre) analyses up to a maximum time of approximately 2000 years. Parametric thermoelastic type analyses could then be readily obtained to determine the influence of the thermomechanical properties. Recommendations for further study include parametric analyses, plasticity analyses, consideration of the material interfaces as joints, and possibly consideration of a global joint pattern (i.e. jointed at the same orientation everywhere) for the non-salt materials. Subsequently, the viscoelastic analyses could be performed

Rapid and recent diversification patterns in Anseriformes birds: Inferred from molecular phylogeny and diversification analyses.

Science.gov (United States)

Sun, Zhonglou; Pan, Tao; Hu, Chaochao; Sun, Lu; Ding, Hengwu; Wang, Hui; Zhang, Chenling; Jin, Hong; Chang, Qing; Kan, Xianzhao; Zhang, Baowei

2017-01-01

The Anseriformes is a well-known and widely distributed bird order, with more than 150 species in the world. This paper aims to revise the classification, determine the phylogenetic relationships and diversification patterns in Anseriformes by exploring the Cyt b, ND2, COI genes and the complete mitochondrial genomes (mito-genomes). Molecular phylogeny and genetic distance analyses suggest that the Dendrocygna species should be considered as an independent family, Dendrocygnidae, rather than a member of Anatidae. Molecular timescale analyses suggests that the ancestral diversification occurred during the Early Eocene Climatic Optimum (58 ~ 50 Ma). Furthermore, diversification analyses showed that, after a long period of constant diversification, the median initial speciation rate was accelerated three times, and finally increased to approximately 0.3 sp/My. In the present study, both molecular phylogeny and diversification analyses results support that Anseriformes birds underwent rapid and recent diversification in their evolutionary history, especially in modern ducks, which show extreme diversification during the Plio-Pleistocene (~ 5.3 Ma). Therefore, our study support that the Plio-Pleistocene climate fluctuations are likely to have played a significant role in promoting the recent diversification for Anseriformes.

Rapid and recent diversification patterns in Anseriformes birds: Inferred from molecular phylogeny and diversification analyses.

Directory of Open Access Journals (Sweden)

Zhonglou Sun

Full Text Available The Anseriformes is a well-known and widely distributed bird order, with more than 150 species in the world. This paper aims to revise the classification, determine the phylogenetic relationships and diversification patterns in Anseriformes by exploring the Cyt b, ND2, COI genes and the complete mitochondrial genomes (mito-genomes. Molecular phylogeny and genetic distance analyses suggest that the Dendrocygna species should be considered as an independent family, Dendrocygnidae, rather than a member of Anatidae. Molecular timescale analyses suggests that the ancestral diversification occurred during the Early Eocene Climatic Optimum (58 ~ 50 Ma. Furthermore, diversification analyses showed that, after a long period of constant diversification, the median initial speciation rate was accelerated three times, and finally increased to approximately 0.3 sp/My. In the present study, both molecular phylogeny and diversification analyses results support that Anseriformes birds underwent rapid and recent diversification in their evolutionary history, especially in modern ducks, which show extreme diversification during the Plio-Pleistocene (~ 5.3 Ma. Therefore, our study support that the Plio-Pleistocene climate fluctuations are likely to have played a significant role in promoting the recent diversification for Anseriformes.

Preparation of lanthanum sulfide nanoparticles by thermal decomposition of lanthanum complex

Institute of Scientific and Technical Information of China (English)

LI Peisen; LI Huanyong; JIE Wanqi

2011-01-01

γ-La2S3 nanoparticles were successfully prepared by thermal decomposition of lanthanum complex La(Et2S2CN)3·phen at low temperature. The obtained sample was characterized by the X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and element analysis. The decomposition mechanism of lanthanum complex was studied by thermogravimetric analyses (TGA). The results showed that the obtained samples were cubic phase particles with uniform sizes among 10-30 nm and γ-La2S3 was prepared by decomposition of La(Et2S2CN)3 phen via La4(Et2S2CN)3 as an intermediate product. The band gap of γ-La2S3 was 2.97 eV, which was bigger than bulk crystal because of pronounced quantum confinement effect.

Microbial screening of thorium(IV) and dioxouranium(VI) chelates with oxine and phenols

International Nuclear Information System (INIS)

Kapadia, M.A.; Patel, M.M.; Patel, G.P.; Joshi, J.D.

2007-01-01

In the present investigation synthesis, characterization of mixed ligand chelates of the type MA 2 L 2 , where, M = Th 4+ and UO 2 2+ , A 8-hydroxyquinoline (oxine) and L = phenols, H2L I = catechol, H 2 L 2 pyrogallol, H 2 L 3 = 2,3-dihydroxy naphthalene, H 2 L 4 = 1,5-dihydroxy naphthalene and H 2 L 5 = 1,7-dihydroxy naphthalene have been reported. Their geometry have been elucidated on the basis of elemental analyses, thermogravimetric, magnetic moments, NMR, IR and electronic spectra. A study of thermal properties has also been carried out. The antimicrobial activity of 8-hydroxyquinoline and MA 2 L 2 chelates have been determined and described. All the chelates showed an effective antimicrobial activity than the free ligand. (author)

Effect of Cross-Linking on the Mechanical and Thermal Properties of Poly(amidoamine) Dendrimer/Poly(vinyl alcohol) Hybrid Membranes for CO2 Separation.

Science.gov (United States)

Duan, Shuhong; Kai, Teruhiko; Saito, Takashi; Yamazaki, Kota; Ikeda, Kenichi

2014-04-08

Poly(amidoamine) (PAMAM) dendrimers were incorporated into cross-linked poly(vinyl alcohol) (PVA) matrix to improve carbon dioxide (CO2) separation performance at elevated pressures. In our previous studies, PAMAM/PVA hybrid membranes showed high CO2 separation properties from CO2/H2 mixed gases. In this study, three types of organic Ti metal compounds were selected as PVA cross-linkers that were used to prepare PAMAM/cross-linked PVA hybrid membranes. Characterization of the PAMAM/cross-linked PVA hybrid membranes was conducted using nanoindentation and thermogravimetric analyses. The effects of the cross-linker and CO2 partial pressure in the feed gas on CO2 separation performance were discussed. H2O and CO2 sorption of the PAMAM/PVA hybrid membranes were investigated to explain the obtained CO2 separation efficiencies.

Preparation and thermal characterization of oxalic acid dihydrate/bentonite composite as shape-stabilized phase change materials for thermal energy storage

Science.gov (United States)

Han, Lipeng; Xie, Shaolei; Sun, Jinhe; Jia, Yongzhong

2017-03-01

Oxalic acid dihydrate (OAD) which has very high initial phase transition enthalpy is a promising phase change material (PCM). In this paper, shape-stabilized composite PCMs composed of OAD and bentonite were prepared by a facile blending method to overcome the problem of leakage. FT-IR results indicated the interactions between OAD and bentonite, such as the capillary force and the hydrogen bonding, resulting in the confined crystallization process. As a result, the OAD was confined to be amorphous. The thermogravimetric analysis and scanning electron microscope results showed that sample had the best coating effect when the amount of bentonite was 17.7%. The differential scanning calorimetry analyses demonstrated that a decrease in the OAD content was accompanied by a continuous decrease in the melting point and phase change enthalpy of the composites.

Uncertainty and Sensitivity Analyses Plan

International Nuclear Information System (INIS)

Simpson, J.C.; Ramsdell, J.V. Jr.

1993-04-01

Hanford Environmental Dose Reconstruction (HEDR) Project staff are developing mathematical models to be used to estimate the radiation dose that individuals may have received as a result of emissions since 1944 from the US Department of Energy's (DOE) Hanford Site near Richland, Washington. An uncertainty and sensitivity analyses plan is essential to understand and interpret the predictions from these mathematical models. This is especially true in the case of the HEDR models where the values of many parameters are unknown. This plan gives a thorough documentation of the uncertainty and hierarchical sensitivity analysis methods recommended for use on all HEDR mathematical models. The documentation includes both technical definitions and examples. In addition, an extensive demonstration of the uncertainty and sensitivity analysis process is provided using actual results from the Hanford Environmental Dose Reconstruction Integrated Codes (HEDRIC). This demonstration shows how the approaches used in the recommended plan can be adapted for all dose predictions in the HEDR Project

Biomass feedstock analyses

Energy Technology Data Exchange (ETDEWEB)

Wilen, C.; Moilanen, A.; Kurkela, E. [VTT Energy, Espoo (Finland). Energy Production Technologies

1996-12-31

The overall objectives of the project `Feasibility of electricity production from biomass by pressurized gasification systems` within the EC Research Programme JOULE II were to evaluate the potential of advanced power production systems based on biomass gasification and to study the technical and economic feasibility of these new processes with different type of biomass feed stocks. This report was prepared as part of this R and D project. The objectives of this task were to perform fuel analyses of potential woody and herbaceous biomasses with specific regard to the gasification properties of the selected feed stocks. The analyses of 15 Scandinavian and European biomass feed stock included density, proximate and ultimate analyses, trace compounds, ash composition and fusion behaviour in oxidizing and reducing atmospheres. The wood-derived fuels, such as whole-tree chips, forest residues, bark and to some extent willow, can be expected to have good gasification properties. Difficulties caused by ash fusion and sintering in straw combustion and gasification are generally known. The ash and alkali metal contents of the European biomasses harvested in Italy resembled those of the Nordic straws, and it is expected that they behave to a great extent as straw in gasification. Any direct relation between the ash fusion behavior (determined according to the standard method) and, for instance, the alkali metal content was not found in the laboratory determinations. A more profound characterisation of the fuels would require gasification experiments in a thermobalance and a PDU (Process development Unit) rig. (orig.) (10 refs.)

Analyser Framework to Verify Software Components

Directory of Open Access Journals (Sweden)

Rolf Andreas Rasenack

2009-01-01

Full Text Available Today, it is important for software companies to build software systems in a short time-interval, to reduce costs and to have a good market position. Therefore well organized and systematic development approaches are required. Reusing software components, which are well tested, can be a good solution to develop software applications in effective manner. The reuse of software components is less expensive and less time consuming than a development from scratch. But it is dangerous to think that software components can be match together without any problems. Software components itself are well tested, of course, but even if they composed together problems occur. Most problems are based on interaction respectively communication. Avoiding such errors a framework has to be developed for analysing software components. That framework determines the compatibility of corresponding software components. The promising approach discussed here, presents a novel technique for analysing software components by applying an Abstract Syntax Language Tree (ASLT. A supportive environment will be designed that checks the compatibility of black-box software components. This article is concerned to the question how can be coupled software components verified by using an analyzer framework and determines the usage of the ASLT. Black-box Software Components and Abstract Syntax Language Tree are the basis for developing the proposed framework and are discussed here to provide the background knowledge. The practical implementation of this framework is discussed and shows the result by using a test environment.

Risico-analyse brandstofpontons

NARCIS (Netherlands)

Uijt de Haag P; Post J; LSO

2001-01-01

Voor het bepalen van de risico's van brandstofpontons in een jachthaven is een generieke risico-analyse uitgevoerd. Er is een referentiesysteem gedefinieerd, bestaande uit een betonnen brandstofponton met een relatief grote inhoud en doorzet. Aangenomen is dat de ponton gelegen is in een

Statistical analyses of extreme food habits

International Nuclear Information System (INIS)

Breuninger, M.; Neuhaeuser-Berthold, M.

2000-01-01

This report is a summary of the results of the project ''Statistical analyses of extreme food habits'', which was ordered from the National Office for Radiation Protection as a contribution to the amendment of the ''General Administrative Regulation to paragraph 45 of the Decree on Radiation Protection: determination of the radiation exposition by emission of radioactive substances from facilities of nuclear technology''. Its aim is to show if the calculation of the radiation ingested by 95% of the population by food intake, like it is planned in a provisional draft, overestimates the true exposure. If such an overestimation exists, the dimension of it should be determined. It was possible to prove the existence of this overestimation but its dimension could only roughly be estimated. To identify the real extent of it, it is necessary to include the specific activities of the nuclides, which were not available for this investigation. In addition to this the report shows how the amounts of food consumption of different groups of foods influence each other and which connections between these amounts should be taken into account, in order to estimate the radiation exposition as precise as possible. (orig.) [de

Immature granulocyte detection by the SE-9000 haematology analyser during pregnancy.

Science.gov (United States)

Fernández-Suárez, A; Pascual, V T; Gimenez, M T F; Hernández, J F S

2003-12-01

The objective of this study was to determine the nature of the alarm for immature granulocytes appearing in haemograms from pregnant women, as detected by the immature cell information channel (IMI) of the SE-9000 automated haematology analyser. Of all tests run on pregnant women in a 4-month period (n = 698), the first 100 haemograms with immature granulocyte alarms (14.33%) were collected. Each of these samples was then stained with Wright-Giemsa stain. The following variables were also analysed: age of the mother, trimester and days of gestation, type of delivery, weight and sex of the baby, and Apgar score. Most pregnant women were in the third trimester of gestation (82%) when an alarm was noted on the IMI channel. Of the patients, 62% had normal deliveries. The most frequent complication was obstructed delivery (23%). Mean percentages by microscopic counts of band cells, metamyelocytes, and myelocytes were 2.99, 0.45, and 0.19%, respectively. There was a statistically significant correlation for all cell types between the SE-9000 and the manual count method. No association was observed between the presence of immature granulocytes and the clinical variables analysed. The SE-9000 analyser shows high sensitivity in the IMI channel for detection of immature forms.

Synthesis and mechanism of formation of oxadeazaflavines by microwave thermal cyclization of ortho-halobenzylidene barbiturates

Energy Technology Data Exchange (ETDEWEB)

Figueroa-Villar, J. Daniel; Oliveira, Sandra C.G. de, E-mail: figueroa@ime.eb.br [Grupo de Quimica Medicinal, Departamento de Quimica, Instituto Militar de Engenharia, Rio de Janeiro, RJ (Brazil)

2011-09-15

The thermal cyclization reaction of o-halobenzylidene barbiturates was developed as an efficient and simple method for the preparation of oxadeazaflavines. The use of solid state reaction conditions with microwave irradiation afforded the products in 5 min with 47 to 98% yield. Experimental synthetic results and thermogravimetric reaction analyses agree with the molecular modeling mechanism simulation, indicating that this reaction occurs through an intramolecular hetero-Diels-Alder cyclization followed by fast re-aromatization. (author)

Study of CO2 gasification reactivity of biocarbon produced at different conditions

OpenAIRE

Wang, Liang; Maziarka, Przemysław; Skreiberg, Øyvind; Løvås, Terese; Wadrzyk, Mariusz; Sevault, Alexis

2017-01-01

Biocarbon has a great potential to replace fossil reductants and help reduce greenhouse gas emissions from carbon intensive metallurgical industries. In this work, biocarbon samples were produced from Norway spruce under different final temperatures (550, 650 and 800 °C) and holding times (10 and 30 minutes). The CO2 gasification reactivity of the biocarbon, or biomass char, samples was investigated in a thermogravimetric analyser at different gasification temperatures (850, 900 and 950 °C). ...

我国某矿田硫化物和硫盐类矿物差热失重分析的研究

Institute of Scientific and Technical Information of China (English)

陈国玺

1976-01-01

DTA and TGA curves are presented for 117 samples of sulfide and sulfosalt minerals from a certain eassiterite-sulfide deposit. The differential thermal and thermogravimetric analyses were conducted under oxidation conditions and in inert atmospheres by use of China-made Model 4.1 Precise Differential Thermebalance. In conjunction with X-ray diffraction analysis, pyrrhotite and chaleopyrite of different crystal systems, silver-bearlng galena, jamesonite and boulangerite have been studied in more detail.

Identification and Characterisation CRN Effectors in Phytophthora capsici Shows Modularity and Functional Diversity.

Directory of Open Access Journals (Sweden)

Remco Stam

Full Text Available Phytophthora species secrete a large array of effectors during infection of their host plants. The Crinkler (CRN gene family encodes a ubiquitous but understudied class of effectors with possible but as of yet unknown roles in infection. To appreciate CRN effector function in Phytophthora, we devised a simple Crn gene identification and annotation pipeline to improve effector prediction rates. We predicted 84 full-length CRN coding genes and assessed CRN effector domain diversity in sequenced Oomycete genomes. These analyses revealed evidence of CRN domain innovation in Phytophthora and expansion in the Peronosporales. We performed gene expression analyses to validate and define two classes of CRN effectors, each possibly contributing to infection at different stages. CRN localisation studies revealed that P. capsici CRN effector domains target the nucleus and accumulate in specific sub-nuclear compartments. Phenotypic analyses showed that few CRN domains induce necrosis when expressed in planta and that one cell death inducing effector, enhances P. capsici virulence on Nicotiana benthamiana. These results suggest that the CRN protein family form an important class of intracellular effectors that target the host nucleus during infection. These results combined with domain expansion in hemi-biotrophic and necrotrophic pathogens, suggests specific contributions to pathogen lifestyles. This work will bolster CRN identification efforts in other sequenced oomycete species and set the stage for future functional studies towards understanding CRN effector functions.

Grey literature in meta-analyses.

Science.gov (United States)

Conn, Vicki S; Valentine, Jeffrey C; Cooper, Harris M; Rantz, Marilyn J

2003-01-01

In meta-analysis, researchers combine the results of individual studies to arrive at cumulative conclusions. Meta-analysts sometimes include "grey literature" in their evidential base, which includes unpublished studies and studies published outside widely available journals. Because grey literature is a source of data that might not employ peer review, critics have questioned the validity of its data and the results of meta-analyses that include it. To examine evidence regarding whether grey literature should be included in meta-analyses and strategies to manage grey literature in quantitative synthesis. This article reviews evidence on whether the results of studies published in peer-reviewed journals are representative of results from broader samplings of research on a topic as a rationale for inclusion of grey literature. Strategies to enhance access to grey literature are addressed. The most consistent and robust difference between published and grey literature is that published research is more likely to contain results that are statistically significant. Effect size estimates of published research are about one-third larger than those of unpublished studies. Unfunded and small sample studies are less likely to be published. Yet, importantly, methodological rigor does not differ between published and grey literature. Meta-analyses that exclude grey literature likely (a) over-represent studies with statistically significant findings, (b) inflate effect size estimates, and (c) provide less precise effect size estimates than meta-analyses including grey literature. Meta-analyses should include grey literature to fully reflect the existing evidential base and should assess the impact of methodological variations through moderator analysis.

Cost-Benefit Analyses of Transportation Investments

DEFF Research Database (Denmark)

Næss, Petter

2006-01-01

This paper discusses the practice of cost-benefit analyses of transportation infrastructure investment projects from the meta-theoretical perspective of critical realism. Such analyses are based on a number of untenable ontological assumptions about social value, human nature and the natural......-to-pay investigations. Accepting the ontological and epistemological assumptions of cost-benefit analysis involves an implicit acceptance of the ethical and political values favoured by these assumptions. Cost-benefit analyses of transportation investment projects tend to neglect long-term environmental consequences...

Automatic incrementalization of Prolog based static analyses

DEFF Research Database (Denmark)

Eichberg, Michael; Kahl, Matthias; Saha, Diptikalyan

2007-01-01

Modem development environments integrate various static analyses into the build process. Analyses that analyze the whole project whenever the project changes are impractical in this context. We present an approach to automatic incrementalization of analyses that are specified as tabled logic prog...

Pectins filled with LDH-antimicrobial molecules: preparation, characterization and physical properties.

Science.gov (United States)

Gorrasi, Giuliana; Bugatti, Valeria; Vittoria, Vittoria

2012-06-05

Nanohybrids of layered double hydroxide (LDH) with intercalated active molecules: benzoate, 2,4-dichlorobenzoate, para-hydroxybenzoate and ortho-hydroxybenzoate, were incorporated into pectins from apples through high energy ball milling in the presence of water. Cast films were obtained and analysed. X-ray diffraction analysis showed a complete destructuration of all nanohybrids in the pectin matrix. Thermogravimetric analysis showed a better thermal resistance of pectin in the presence of fillers, especially para-hydroxybenzoate and ortho-hydroxybenzoate. Mechanical properties showed an improvement of elastic modulus in particular for LDH-para-hydroxybenzoate nanohybrid, due probably to a better interaction between pectin matrix and nanohybrid layers. Barrier properties (sorption and diffusion) to water vapour showed improvement in the dependence on the intercalated active molecule, the best improvement was achieved for composites containing para-hydroxybenzoate molecules, suggesting that the interaction between the filler phase and the polymer plays an important role in sorption and diffusion phenomena. Incorporation of these active molecules gave antimicrobial properties to the composite films giving opportunities in the field of active packaging. Copyright © 2012 Elsevier Ltd. All rights reserved.

Sample preparation in foodomic analyses.

Science.gov (United States)

Martinović, Tamara; Šrajer Gajdošik, Martina; Josić, Djuro

2018-04-16

Representative sampling and adequate sample preparation are key factors for successful performance of further steps in foodomic analyses, as well as for correct data interpretation. Incorrect sampling and improper sample preparation can be sources of severe bias in foodomic analyses. It is well known that both wrong sampling and sample treatment cannot be corrected anymore. These, in the past frequently neglected facts, are now taken into consideration, and the progress in sampling and sample preparation in foodomics is reviewed here. We report the use of highly sophisticated instruments for both high-performance and high-throughput analyses, as well as miniaturization and the use of laboratory robotics in metabolomics, proteomics, peptidomics and genomics. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Genetic connections between dressage and show-jumping horses in Dutch Warmblood horses

DEFF Research Database (Denmark)

Rovere, Gabriel; Madsen, Per; Norberg, Elise

2014-01-01

During the last decades, the breeding practice within the Dutch Warmblood studbook (KWPN) has resulted in an increasing specialisation of horses into show-jumping (JH) and dressage (DH). The objective of this study was to describe the effect of the specialisation on the connectedness between...... and within subpopulations were analysed in three periods of time to describe changes in genetic connectedness between subpopulations. A decline in GS (0.97–0.45), GC0.5 (0.69–0.13) and r (0.018–0.014) in the recent years was observed. Both subpopulations have a common genetic pool; however...

Two multi-dimensional frameworks constructed from zinc coordination polymers with pyridine carboxylic acids

International Nuclear Information System (INIS)

Guo Yuanyuan; Ma Pengtao; Wang Jingping; Niu Jingyang

2011-01-01

Two novel zinc coordination polymers [Zn 2 (H 2 O)L(MoO 4 )] n (1) and [Zn 4 (PO 4 ) 2 L'(H 2 O)] n (2) (H 2 L=2,2'-bipyridine-6.6'-dicarboxylic acid, H 2 L'=2,2'-bipyridine-4,4'-dicarboxylic acid) have been hydrothermally synthesized and characterized by elemental analyses, IR spectra, UV spectra, single-crystal X-ray diffraction and thermogravimetric analyses. Structural analyses indicate that 1 represents a 2-D sheet structure built by dimeric [Zn 2 L(H 2 O)] 2+ units and MoO 4 2- groups whereas 2 displays an interesting 3-D framework constructed by tetranuclear zinc clusters, L' 2- ligands and PO 4 3- groups. Examination of UV spectra suggests that both 1 and 2 can stably exist in the pH range of 2.45-5.45 and 3.01-8.55 in aqueous solution, respectively. The room-temperature solid-state photoluminescence of 1 and 2 are derived from the intra-ligands π-π* transitions of H 2 L and H 2 L' ligands and the ligand-to-metal-charge-transfer transitions. - Graphical Abstract: Two new transition metal coordination polymers, namely, [Zn 2 (H 2 O)L 1 (MoO 4 )] n (1), [Zn 4 (PO 4 ) 2 L 2 (H 2 O)] n (2) (H 2 L 1 =2,2'-bipyridine-6,6'-dicarboxylic acid, H 2 L 2 =2,2'-bipyridine-4,4'-dicarboxylic acid) have been hydrothermally synthesized. 1 represents a 2-D sheet structure while 2 represents 3-D network. Highlights: →Two new transition metal coordination polymers have been hydrothermally synthesized. → The two compounds have been characterized by elemental analyses, IR, UV spectra, single-crystal X-ray diffraction, thermogravimetric analyses and photoluminescence. → Compound 1 represents a 2-D sheet structure while 2 represents 3-D network.

Sustained release of anticancer agent phytic acid from its chitosan-coated magnetic nanoparticles for drug-delivery system.

Science.gov (United States)

Barahuie, Farahnaz; Dorniani, Dena; Saifullah, Bullo; Gothai, Sivapragasam; Hussein, Mohd Zobir; Pandurangan, Ashok Kumar; Arulselvan, Palanisamy; Norhaizan, Mohd Esa

2017-01-01

Chitosan (CS) iron oxide magnetic nanoparticles (MNPs) were coated with phytic acid (PTA) to form phytic acid-chitosan-iron oxide nanocomposite (PTA-CS-MNP). The obtained nanocomposite and nanocarrier were characterized by powder X-ray diffraction, Fourier transform infrared spectroscopy, vibrating sample magnetometry, transmission electron microscopy, and thermogravimetric and differential thermogravimetric analyses. Fourier transform infrared spectra and thermal analysis of MNPs and PTA-CS-MNP nanocomposite confirmed the binding of CS on the surface of MNPs and the loading of PTA in the PTA-CS-MNP nanocomposite. The coating process enhanced the thermal stability of the anticancer nanocomposite obtained. X-ray diffraction results showed that the MNPs and PTA-CS-MNP nanocomposite are pure magnetite. Drug loading was estimated using ultraviolet-visible spectroscopy and showing a 12.9% in the designed nanocomposite. Magnetization curves demonstrated that the synthesized MNPs and nanocomposite were superparamagnetic with saturation magnetizations of 53.25 emu/g and 42.15 emu/g, respectively. The release study showed that around 86% and 93% of PTA from PTA-CS-MNP nanocomposite could be released within 127 and 56 hours by a phosphate buffer solution at pH 7.4 and 4.8, respectively, in a sustained manner and governed by pseudo-second order kinetic model. The cytotoxicity of the compounds on HT-29 colon cancer cells was evaluated by 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide assay. The HT-29 cell line was more sensitive against PTA-CS-MNP nanocomposite than PTA alone. No cytotoxic effect was observed on normal cells (3T3 fibroblast cells). This result indicates that PTA-CS-MNP nanocomposite can inhibit the proliferation of colon cancer cells without causing any harm to normal cell.

Production and characterization of Lemna minor bio-char and its catalytic application for biogas reforming

International Nuclear Information System (INIS)

Muradov, Nazim; Fidalgo, Beatriz; Gujar, Amit C.; Garceau, Nathaniel; T-Raissi, Ali

2012-01-01

Pyrolysis of fast-growing aquatic biomass - Lemna minor (commonly known as duckweed) with the emphasis on production, characterization and catalytic application of bio-char is reported in this paper. The yield of bio-char was determined as a function of L. minor pyrolysis temperature and sweep gas flow rate. It was found that the pore development during L. minor pyrolysis was not significant and the changes in the reaction conditions (temperature and sweep gas flow rate) did not alter markedly the textural characteristics and BET surface area of the bio-char produced. Thermogravimetric/differential thermogravimetric (TG/DTG) analyses of L. minor and different bio-char samples in inert (helium) and oxidative (air) media showed substantial differences in their TG/DTG patterns. A comparison of scanning electron micrographs (SEM) of L. minor, bio-char and ash indicated that the basic structural features of L. minor remained intact and were not affected by thermolysis. The inorganic ash content of L. minor derived bio-char is significantly higher than that of typical terrestrial (plant) biomass. The energy dispersive spectroscopic (EDS) analysis of L. minor ash showed that it mostly consisted of silica, and small quantities of Na, K and Ca compounds. The treatment of bio-char with CO 2 at 800 °C increased its BET surface area. It was found that CO 2 -treated bio-char exhibited appreciable initial catalytic activity in biogas reforming. -- Highlights: ► New data on characterization of bio-chars derived from Lemna minor are presented. ► Effect of pyrolysis operational parameters on bio-char properties is determined. ► Basic skeletal structure of Lemna minor leaflets does not change during pyrolysis. ► Bio-chars show an appreciable initial catalytic activity for biogas reforming.

LOD score exclusion analyses for candidate QTLs using random population samples.

Science.gov (United States)

Deng, Hong-Wen

2003-11-01

While extensive analyses have been conducted to test for, no formal analyses have been conducted to test against, the importance of candidate genes as putative QTLs using random population samples. Previously, we developed an LOD score exclusion mapping approach for candidate genes for complex diseases. Here, we extend this LOD score approach for exclusion analyses of candidate genes for quantitative traits. Under this approach, specific genetic effects (as reflected by heritability) and inheritance models at candidate QTLs can be analyzed and if an LOD score is < or = -2.0, the locus can be excluded from having a heritability larger than that specified. Simulations show that this approach has high power to exclude a candidate gene from having moderate genetic effects if it is not a QTL and is robust to population admixture. Our exclusion analysis complements association analysis for candidate genes as putative QTLs in random population samples. The approach is applied to test the importance of Vitamin D receptor (VDR) gene as a potential QTL underlying the variation of bone mass, an important determinant of osteoporosis.

Thermogravimetric analysis of combustible waste components

DEFF Research Database (Denmark)

Munther, Anette; Wu, Hao; Glarborg, Peter

In order to gain fundamental knowledge about the co-combustion of coal and waste derived fuels, the pyrolytic behaviors of coal, four typical waste components and their mixtures have been studied by a simultaneous thermal analyzer (STA). The investigated waste components were wood, paper, polypro......In order to gain fundamental knowledge about the co-combustion of coal and waste derived fuels, the pyrolytic behaviors of coal, four typical waste components and their mixtures have been studied by a simultaneous thermal analyzer (STA). The investigated waste components were wood, paper...

A new support measure to quantify the impact of local optima in phylogenetic analyses.

KAUST Repository

Brammer, Grant

2011-09-29

Phylogentic analyses are often incorrectly assumed to have stabilized to a single optimum. However, a set of trees from a phylogenetic analysis may contain multiple distinct local optima with each optimum providing different levels of support for each clade. For situations with multiple local optima, we propose p-support which is a clade support measure that shows the impact optima have on a final consensus tree. Our p-support measure is implemented in our PeakMapper software package. We study our approach on two published, large-scale biological tree collections. PeakMapper shows that each data set contains multiple local optima. p-support shows that both datasets contain clades in the majority consensus tree that are only supported by a subset of the local optima. Clades with low p-support are most likely to benefit from further investigation. These tools provide researchers with new information regarding phylogenetic analyses beyond what is provided by other support measures alone.

Trial sequential analyses of meta-analyses of complications in laparoscopic vs. small-incision cholecystectomy: more randomized patients are needed

DEFF Research Database (Denmark)

Keus, Frederik; Wetterslev, Jørn; Gluud, Christian

2010-01-01

Conclusions based on meta-analyses of randomized trials carry a status of "truth." Methodological components may identify trials with systematic errors ("bias"). Trial sequential analysis (TSA) evaluates random errors in meta-analysis. We analyzed meta-analyses on laparoscopic vs. small-incision ......Conclusions based on meta-analyses of randomized trials carry a status of "truth." Methodological components may identify trials with systematic errors ("bias"). Trial sequential analysis (TSA) evaluates random errors in meta-analysis. We analyzed meta-analyses on laparoscopic vs. small...

Purification of bentonite clays from the district of Cubati, PB, for other uses

International Nuclear Information System (INIS)

Costa, M.R.; Araujo, J.P.; Silva, I.A.; Cardoso, M.A.; Silva, C.D.; Neves, G.A.; Ferreira, H.C.

2012-01-01

The state of Paraiba is responsible for the increased production of crude bentonite in the country, coming from one of the largest mines of Brazil, located in Boa Vista, PB. Recently, in the regions of Cubati and Pedra Lavrada, PB, found new deposits of bentonite that could expand the state reserves. The paper aims at the characterization and development of clay purified using the techniques of screening and hydrocycloning, from bentonite clay recently discovered in the city of Cubati, PB, for various uses. The sample characterization was performed through techniques: granulometric analysis by laser diffraction, X-ray diffraction and chemical analysis by X-ray fluorescence and thermogravimetric and differential thermogravimetric analysis. The results showed that the samples are typical of bentonite clay, and that the purification process using only the hydrocycloning shows better results. (author)

UFO-a multi-analyser option for IN12

Science.gov (United States)

Schmidt, Wolfgang; Rheinstädter, Maikel C.; Raymond, Stephane; Ohl, Michael

2004-07-01

The IN12 instrument is operated by FZ Jülich in collaboration with CEA Grenoble as a CRG-B instrument at the Institut Laue Langevin in Grenoble. As a three-axis spectrometer for cold neutrons it is dedicated for high-resolution studies of low-energy excitations. In the past years the instrument has been continuously improved and it has demonstrated its excellent performance for neutron scattering research. To meet further challenges as a state-of-the-art instrument in the next funding period we will propose to upgrade IN12 with a multi-analyser option similar to planned or existing RITA-type instruments. IN12 will then be optionally equipped with an array of individual analyser blades which can be positioned separately in order to map the scattered beam on a user-chosen path in (Q,ω)-space. We refer to this set-up as IN12-UFO (universal focusing option). Both, the feasibility and the scientific case are currently being studied. On the conference we will show details of the planned instrumental set-up and demonstrate its flexibility and multiplex advantages for specific physical applications.

UFO--a multi-analyser option for IN12

Energy Technology Data Exchange (ETDEWEB)

Schmidt, Wolfgang; Rheinstaedter, Maikel C.; Raymond, Stephane; Ohl, Michael

2004-07-15

The IN12 instrument is operated by FZ Juelich in collaboration with CEA Grenoble as a CRG-B instrument at the Institut Laue Langevin in Grenoble. As a three-axis spectrometer for cold neutrons it is dedicated for high-resolution studies of low-energy excitations. In the past years the instrument has been continuously improved and it has demonstrated its excellent performance for neutron scattering research. To meet further challenges as a state-of-the-art instrument in the next funding period we will propose to upgrade IN12 with a multi-analyser option similar to planned or existing RITA-type instruments. IN12 will then be optionally equipped with an array of individual analyser blades which can be positioned separately in order to map the scattered beam on a user-chosen path in (Q,{omega})-space. We refer to this set-up as IN12-UFO (universal focusing option). Both, the feasibility and the scientific case are currently being studied. On the conference we will show details of the planned instrumental set-up and demonstrate its flexibility and multiplex advantages for specific physical applications.

UFO--a multi-analyser option for IN12

International Nuclear Information System (INIS)

Schmidt, Wolfgang; Rheinstaedter, Maikel C.; Raymond, Stephane; Ohl, Michael

2004-01-01

The IN12 instrument is operated by FZ Juelich in collaboration with CEA Grenoble as a CRG-B instrument at the Institut Laue Langevin in Grenoble. As a three-axis spectrometer for cold neutrons it is dedicated for high-resolution studies of low-energy excitations. In the past years the instrument has been continuously improved and it has demonstrated its excellent performance for neutron scattering research. To meet further challenges as a state-of-the-art instrument in the next funding period we will propose to upgrade IN12 with a multi-analyser option similar to planned or existing RITA-type instruments. IN12 will then be optionally equipped with an array of individual analyser blades which can be positioned separately in order to map the scattered beam on a user-chosen path in (Q,ω)-space. We refer to this set-up as IN12-UFO (universal focusing option). Both, the feasibility and the scientific case are currently being studied. On the conference we will show details of the planned instrumental set-up and demonstrate its flexibility and multiplex advantages for specific physical applications