WorldWideScience

Sample records for thermo-reactive deposition technique

  1. Electrochemical and wear behavior of niobium-vanadium carbide coatings produced on AISI H13 tool steel through thermo-reactive deposition/diffusion

    International Nuclear Information System (INIS)

    Castillejo Nieto, Fabio Enrique; Olaya Flores, Jhon Jairo; Alfonso Orjuela, Jose Edgar

    2016-01-01

    We deposited of niobium-vanadium carbide coatings on tool steel AISI H13 using the thermo-reactive substrates deposition/diffusion (TRD) technique. The carbides were obtained using salt baths composed of molten borax, ferroniobium, vanadium and aluminum, by heating this mixture at 1020°C for 4 hours. The coatings were characterized morphologically via electron microscopy scanning (SEM), the chemical surface composition was determined through X-ray photoelectron spectroscopy (XPS) and energy dispersive X-ray spectroscopy (EDX); the crystal structure was analyzed using x-ray diffraction (XRD), the mechanical properties of the coatings were evaluated using nano-indentation, The tribological properties of the coatings obtained were determined using a Pin-on-disk tribometer and the electrochemical behavior was studied through potentiodynamic polarization curves and electrochemical impedance spectroscopy (EIS). The results showed that the hardness of the coated steel increased four times with respect to uncoated steel, and the electrochemical test established that the corrosion current is lower by one order of magnitude for coated steel

  2. Electrochemical characterization of V{sub x}Nb{sub y}C{sub z}/Bi{sub x}Ti{sub y}O{sub z} coatings produced through thermo-reactive diffusion and the sputtering technique

    Energy Technology Data Exchange (ETDEWEB)

    Castro H, S. A.; Alfonso, J. E.; Olaya, J. J., E-mail: jealfonso@unal.edu.co [Universidad Nacional de Colombia, Departamento de Fisica, Grupo de Ciencia de Materiales y Superficies, AA-14490 Bogota (Colombia)

    2016-11-01

    We present and experimental study of the structural evolution of a bilayer V{sub x}Nb{sub y}C{sub z}/Bi{sub x}Ti{sub y}O{sub z} coating produced via thermo-reactive diffusion (TRD) and the RF sputtering process on D-2 steel substrate. The TRD treatments were carried out in a molten mixture consisting of borax, ferro-niobium, ferro-vanadium, and aluminum, at 1313 K for 3 hours, using a resistance-heating furnace. Bi{sub x}Ti{sub y}O{sub z} coatings were deposited using RF magnetron sputtering on TRD coatings, in order to carry out a study of the corrosion behavior of this compound. The crystallographic structure of the coatings was determined via X-ray diffraction, the corrosion resistance was analyzed through the potentiodynamic polarization test (Tafel Extrapolation) and electrochemical impedance spectroscopic analysis (EIS). X-ray diffraction patterns showed that the ternary coating (VNbC{sub 2}) was preferentially oriented along the [200] direction with a cubic-centered face structure, and the Bi{sub x}Ti{sub y}O{sub z} coatings were amorphous. The electrochemical studies showed that the resistance corrosion of the coatings increased with respect to the bare substrate, and that polarization resistance in the bilayer coatings increased with respect to the ternary coatings, suggesting that the titanate has anti corrosive barrier effects. (Author)

  3. Characterization of Transition Metal Carbide Layers Synthesized by Thermo-reactive Diffusion Processes

    DEFF Research Database (Denmark)

    Laursen, Mads Brink; Fernandes, Frederico Augusto Pires; Christiansen, Thomas Lundin

    2015-01-01

    Hard wear resistant surface layers of transition metal carbides can be produced by thermo-reactive diffusion processes where interstitial elements from a steel substrate together with external sources of transition metals (Ti, V, Cr etc.) form hard carbide and/or nitride layers at the steel surface....... In this study halide-activated pack cementation techniques were used on tool steel Vanadis 6 and martensitic stainless steel AISI 420 in order to produce hard layers of titanium carbide (TiC), vanadium carbide (V8C7) and chromium carbides (Cr23C6 and Cr7C3). Surface layers were characterized by scanning...... electron microscopy, X-ray diffraction and Vickers hardness testing. The study shows that porosityfree, homogenous and very hard surface layers can be produced by thermo-reactive diffusion processes. The carbon availability of the substrate influences thickness of obtained layers, as Vanadis 6 tool steel...

  4. Hard Surface Layers by Pack Boriding and Gaseous Thermo-Reactive Deposition and Diffusion Treatments

    DEFF Research Database (Denmark)

    Christiansen, Thomas Lundin; Bottoli, Federico; Dahl, Kristian Vinter

    2017-01-01

    subjected to TRD (chromizing and titanizing) and boriding treatments. For the steels with low carbon content, chromizing results in surface alloying with chromium, i.e., formation of a (soft) “stainless” surface zone. Steels containing higher levels of carbon form chromium carbide (viz. Cr23C6, Cr7C3......) layers with hardnesses up to 1800 HV. Titanizing of ARNE tool steel results in a surface layer consisting of TiC with a hardness of approximately 4000 HV. Duplex treatments, where boriding is combined with subsequent (TRD) titanizing, result in formation of hard TiB2 on top of a thick layer of Fe...

  5. Sequential deposition etch techniques for the selective deposition of tungsten

    Energy Technology Data Exchange (ETDEWEB)

    Fleming, J.G.; Omstead, T.R.; Dominguez, F.

    1991-01-01

    We report on the use of a deposition/etch approach to the loss of selectivity problem, using high activity fluorine chemistries in the etch step. Proof-of-concept experiments were initially performed in a hot wall system, the excellent results obtained lead us to prove out the concept in a commercially available cold wall Genus reactor. We observed that WF{sub 6} is ineffective as an etchant of W. The technique has been able to produce perfectly selective depositions 1 micron thick in both hot wall, and cold wall, systems. Sheet resistivity values and film morphology are good. 9 refs., 4 figs., 1 tab.

  6. Magnetic filtered plasma deposition and implantation technique

    CERN Document Server

    Zhang Hui Xing; Wu Xian Ying

    2002-01-01

    A high dense metal plasma can be produced by using cathodic vacuum arc discharge technique. The microparticles emitted from the cathode in the metal plasma can be removed when the metal plasma passes through the magnetic filter. It is a new technique for making high quality, fine and close thin films which have very widespread applications. The authors describe the applications of cathodic vacuum arc technique, and then a filtered plasma deposition and ion implantation system as well as its applications

  7. Sputtering. [as deposition technique in mechanical engineering

    Science.gov (United States)

    Spalvins, T.

    1976-01-01

    This paper primarily reviews the potential of using the sputtering process as a deposition technique; however, the manufacturing and sputter etching aspects are also discussed. Since sputtering is not regulated by classical thermodynamics, new multicomponent materials can be developed in any possible chemical composition. The basic mechanism for dc and rf sputtering is described. Sputter-deposition is described in terms of the unique advantageous features it offers such as versatility, momentum transfer, stoichiometry, sputter-etching, target geometry (coating complex surfaces), precise controls, flexibility, ecology, and sputtering rates. Sputtered film characteristics, such as strong adherence and coherence and film morphology, are briefly evaluated in terms of varying the sputtering parameters. Also described are some of the specific industrial areas which are turning to sputter-deposition techniques.

  8. Techniques for freeing deposited canisters. Final report

    International Nuclear Information System (INIS)

    Kalbantner, P.; Sjoeblom, R.

    2000-06-01

    Four different techniques for removal of the bentonite buffer around a deposited canister have been identified, studied and evaluated: mechanical, hydrodynamical, thermal, and electrical techniques. Different techniques to determine the position of the canister in the buffer have also been studied: mechanical, electromagnetic, thermal and acoustic techniques. The mechanical techniques studied are full-face boring, milling and core-drilling. It is expected that the bentonite can be machined relatively easily. It is assessed that cooling by means of flushing water over the outer surfaces of the tools is not feasible in view of the tendency of bentonite to form a gel. The mechanical techniques are characterized by the potential of damaging the canister, a high degree of complexity, and high requirements of energy/power input. The generated byproduct is solid and cannot be removed by means of flushing. Removal is assessed to be simplest in conjunction with full-face boring and most difficult when coredrilling is applied. The hydrodynamical techniques comprise high-pressure hydrodynamic techniques, where pressures above and below 100 bar, and low pressure hydrodynamical techniques (< 10 bar) are separated. At pressures above 100 bar, a water jet with a diameter of approximately a millimetre cuts through the material. If desired, sand can be added to the jet. At pressures below 100 bar the jet has a diameter of one or a few centimetres. The liquid contains a few percent of salt, which is essential for the efficiency of the process. The flushing is important not only because it removes the modified bentonite but also because it frees previously unaffected bentonite and thereby makes it accessible to chemical modification. All of the hydrodynamical techniques are applicable for freeing the end surface as well as the mantle surface. The degree of complexity and the requirement on energy/power decrease with a decrease in pressure. A significant potential for damaging the

  9. Isotropic metal deposition technique for metamaterials fabrication

    DEFF Research Database (Denmark)

    Malureanu, Radu; Andryieuski, Andrei; Lavrinenko, Andrei

    2009-01-01

    In this work we will present the first steps taken towards isotropic deposition of thin metallic layers on dielectric substrates. The deposition takes place in aqueous environment thus making it both cheap and easy to be implemented....

  10. Cuprous oxide thin films grown by hydrothermal electrochemical deposition technique

    International Nuclear Information System (INIS)

    Majumder, M.; Biswas, I.; Pujaru, S.; Chakraborty, A.K.

    2015-01-01

    Semiconducting cuprous oxide films were grown by a hydrothermal electro-deposition technique on metal (Cu) and glass (ITO) substrates between 60 °C and 100 °C. X-ray diffraction studies reveal the formation of cubic cuprous oxide films in different preferred orientations depending upon the deposition technique used. Film growth, uniformity, grain size, optical band gap and photoelectrochemical response were found to improve in the hydrothermal electrochemical deposition technique. - Highlights: • Cu 2 O thin films were grown on Cu and glass substrates. • Conventional and hydrothermal electrochemical deposition techniques were used. • Hydrothermal electrochemical growth showed improved morphology, thickness and optical band gap

  11. Comparison of different experimental techniques used for wax deposition testing

    Energy Technology Data Exchange (ETDEWEB)

    Allenson, Stephen; Johnston, Angela [Nalco Energy Services, Sugar Land, TX (United States)

    2008-07-01

    Crude oils consist of various fractions of hydrocarbons, including n-paraffins. The paraffins precipitate out of oil below the temperature called WAT (wax appearance temperature) and accumulate in flow lines and pipelines causing major transport problems. Prediction of paraffin deposition is, therefore, a key element of flow assurance programs. The purpose of this study was to develop a general and reliable approach to prediction of wax deposition based on a critical comparison of several practical lab techniques. Wax deposition study was conducted on five separate crude oils by using a varying protocols and equipment. One experimental technique was a cold stress test of wax deposition combined with ketone precipitation of waxy paraffin crystals. Another set of experiments were carried out for wax deposits formed on the surface of U-tubes and cold fingers of different designs. A comparison of the effectiveness of several wax inhibitors was conducted for these crude oils by using the selected deposition techniques. In each test method the amount of precipitated wax was recorded and compared. The deposits were characterized by melting point, qualitative and quantitative analysis of the wax components using DSC, SARA and HTGC analyses. Efficiency of paraffin inhibitors was correlated with a profile of n-paraffins distribution in the deposits. The limitations and advantages of different deposition techniques were analyzed and discussed. (author)

  12. Characterization of wax deposition by different experimental techniques - a comparison

    Energy Technology Data Exchange (ETDEWEB)

    Lindeman, Olga; Allenson, Steve

    2006-03-15

    Crude oils consist of various fractions of hydrocarbons, including n-paraffins. The paraffins precipitate out of oil below the temperature called WAT (wax appearance temperature) and accumulate in flow lines causing major transport problems. Prediction of paraffin deposition is, therefore, a key element of flow assurance programs. The purpose of this study was to develop a general and reliable approach to prediction of wax deposition based on a critical comparison of several practical lab techniques. Wax deposition study was conducted on multiple crude oils using various testing protocols and equipment. One experimental technique was a cold stress test of wax deposition combined with ketone precipitation of waxy paraffin crystals. Another set of experiments was carried out for wax deposits formed on the surface of U-tubes and cold fingers of different designs. A comparison of the effectiveness of several wax inhibitors was conducted for these crude oils by using the selected deposition techniques. In each test method the amount of precipitated wax was recorded and compared. The deposits were characterized by melting point, qualitative and quantitative analysis of the wax components using DSC, SARA and HTGC analyses. Efficiency of paraffin inhibitors was correlated with a profile of n-paraffins distribution in the deposits. The limitations and advantages of different deposition techniques were analyzed and discussed. A new test design designated ''cold tube'' is proposed. (Author) (tk)

  13. Chemical vapor deposition: A technique for applying protective coatings

    Energy Technology Data Exchange (ETDEWEB)

    Wallace, T.C. Sr.; Bowman, M.G.

    1979-01-01

    Chemical vapor deposition is discussed as a technique for applying coatings for materials protection in energy systems. The fundamentals of the process are emphasized in order to establish a basis for understanding the relative advantages and limitations of the technique. Several examples of the successful application of CVD coating are described. 31 refs., and 18 figs.

  14. Lipase biofilm deposited by Matrix Assisted Pulsed Laser Evaporation technique

    Science.gov (United States)

    Aronne, Antonio; Bloisi, Francesco; Calabria, Raffaela; Califano, Valeria; Depero, Laura E.; Fanelli, Esther; Federici, Stefania; Massoli, Patrizio; Vicari, Luciano R. M.

    2015-05-01

    Lipase is an enzyme that finds application in biodiesel production and for detection of esters and triglycerides in biosensors. Matrix Assisted Pulsed Laser Evaporation (MAPLE), a technique derived from Pulsed Laser Deposition (PLD) for deposition of undamaged biomolecules or polymers, is characterized by the use of a frozen target obtained from a solution/suspension of the guest material (to be deposited) in a volatile matrix (solvent). The presence of the solvent avoids or at least reduces the potential damage of guest molecules by laser radiation but only the guest material reaches the substrate in an essentially solvent-free deposition. MAPLE can be used for enzymes immobilization, essential for industrial application, allowing the development of continuous processes, an easier separation of products, the reuse of the catalyst and, in some cases, enhancing enzyme properties (pH, temperature stability, etc.) and catalytic activity in non-aqueous media. Here we show that MAPLE technique can be used to deposit undamaged lipase and that the complex structure (due to droplets generated during extraction from target) of the deposited material can be controlled by changing the laser beam fluence.

  15. Fused Deposition Technique for Continuous Fiber Reinforced Thermoplastic

    Science.gov (United States)

    Bettini, Paolo; Alitta, Gianluca; Sala, Giuseppe; Di Landro, Luca

    2017-02-01

    A simple technique for the production of continuous fiber reinforced thermoplastic by fused deposition modeling, which involves a common 3D printer with quite limited modifications, is presented. An adequate setting of processing parameters and deposition path allows to obtain components with well-enhanced mechanical characteristics compared to conventional 3D printed items. The most relevant problems related to the simultaneous feeding of fibers and polymer are discussed. The properties of obtained aramid fiber reinforced polylactic acid (PLA) in terms of impregnation quality and of mechanical response are measured.

  16. Homogeneity analysis of sculptured thin films deposited in symmetric style through glancing angle deposition technique

    International Nuclear Information System (INIS)

    Wang Bin; Qi Hong-Ji; Sun Wei; He Jun; Zhao Jiao-Ling; Wang Hu; Hou Yong-Qiang

    2014-01-01

    The symmetric deposition technique is often used to improve the uniformity of sculptured thin film (STF). In this paper, optical properties of STF with the columnar angles ±β are analyzed theoretically, based on the characteristic matrix method for extraordinary waves. Then, the transmittances of uniformity monolayer and bilayer STF in symmetrical style are calculated to show the effect of the bilayer structure on the optical properties of STF. The inhomogeneity of STF is involved in analyzing the differences in transmittance and phase retardation between monolayer and bilayer STF deposited in symmetric style. The results show that optical homogeneity of STF can be improved by depositing in symmetric style at the normal incidence, but it is not the same case as the oblique incidence. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

  17. Effect of V addition on the hardness, adherence and friction coefficient of VC coatings produced by thermo-reactive diffusion deposition

    OpenAIRE

    Fredy Alejandro Orjuela-Guerrero; José Edgar Alfonso-Orjuela; Jhon Jairo Olaya-Flórez

    2015-01-01

    Se produjeron recubrimientos de carburo de vanadio (VC) sobre sustratos de acero AISI H13 y acero AISI D2 mediante deposito termoreactiva/ difusión (TRD) con el fin de evaluar sus propiedades mecánicas como una función del contenido de vanadio. Los recubrimientos se producen con diferentes porcentajes de concentración de ferrovanadio. La composición química de los recubrimientos se determinó mediante fluorescencia de rayos X (XRF), la estructura cristalina se analizó utilizando difracción de ...

  18. Effect of V addition on the hardness, adherence and friction coefficient of VC coatings produced by thermo-reactive diffusion deposition

    Directory of Open Access Journals (Sweden)

    Fredy Alejandro Orjuela-Guerrero

    2015-01-01

    Full Text Available Se produjeron recubrimientos de carburo de vanadio (VC sobre sustratos de acero AISI H13 y acero AISI D2 mediante deposito termoreactiva/ difusión (TRD con el fin de evaluar sus propiedades mecánicas como una función del contenido de vanadio. Los recubrimientos se producen con diferentes porcentajes de concentración de ferrovanadio. La composición química de los recubrimientos se determinó mediante fluorescencia de rayos X (XRF, la estructura cristalina se analizó utilizando difracción de rayos X (XRD, la morfología se caracterizó usando microscopía electrónica de barrido (SEM, la dureza se midió a través de nanoindentaciòn, y las propiedades tribológicas mediante la prueba de bola sobre disco. El análisis XRF indicó que los recubrimientos crecidos en acero D2 disminuyó el porcentaje atómico de vanadio cuando el recubrimiento se produce con 20% de ferrovanadio. El análisis XRD estableció que los recubrimientos eran policristalinos, con una estructura cúbica. Las imágenes de SEM revelaron que los recubrimientos crecidos en acero D2 eran más compactos que los crecidos en el acero H13. Finalmente, las pruebas de desgaste establecieron que el coeficiente de fricción disminuyó con un aumento de vanadio en el recubrimiento.

  19. Metallization on FDM Parts Using the Chemical Deposition Technique

    OpenAIRE

    Azhar Equbal; Anoop kumar Sood

    2014-01-01

    Metallization of ABS (acrylonitrile-butadiene-styrene) parts has been studied on flat part surfaces. These parts are fabricated on an FDM (fused deposition modeling machine) using the layer-wise deposition principle using ABS as a part material. Electroless copper deposition on ABS parts was performed using two different surface preparation processes, namely ABS parts prepared using chromic acid for etching and ABS parts prepared using a solution mixture of sulphuric acid and hydrogen peroxid...

  20. Metallization on FDM Parts Using the Chemical Deposition Technique

    Directory of Open Access Journals (Sweden)

    Azhar Equbal

    2014-08-01

    Full Text Available Metallization of ABS (acrylonitrile-butadiene-styrene parts has been studied on flat part surfaces. These parts are fabricated on an FDM (fused deposition modeling machine using the layer-wise deposition principle using ABS as a part material. Electroless copper deposition on ABS parts was performed using two different surface preparation processes, namely ABS parts prepared using chromic acid for etching and ABS parts prepared using a solution mixture of sulphuric acid and hydrogen peroxide (H2SO4/H2O2 for etching. After surface preparations using these routes, copper (Cu is deposited electrolessly using four different acidic baths. The acidic baths used are 5 wt% CuSO4 (copper sulfate with 15 wt% of individual acids, namely HF (hydrofluoric acid, H2SO4 (sulphuric acid, H3PO4 (phosphoric acid and CH3COOH (acetic acid. Cu deposition under different acidic baths used for both the routes is presented and compared based on their electrical performance, scanning electron microscopy (SEM and energy dispersive X-ray spectrometry (EDS. The result shows that chromic acid etched samples show better electrical performance and Cu deposition in comparison to samples etched via H2SO4/H2O2.

  1. Crystalline Indium Sulphide thin film by photo accelerated deposition technique

    Science.gov (United States)

    Dhanya, A. C.; Preetha, K. C.; Deepa, K.; Remadevi, T. L.

    2015-02-01

    Indium sulfide thin films deserve special attention because of its potential application as buffer layers in CIGS based solar cells. Highly transparent indium sulfide (InS) thin films were prepared using a novel method called photo accelerated chemical deposition (PCD). Ultraviolet source of 150 W was used to irradiate the solution. Compared to all other chemical methods, PCD scores its advantage for its low cost, flexible substrate and capable of large area of deposition. Reports on deposition of high quality InS thin films at room temperature are very rare in literature. The precursor solution was initially heated to 90°C for ten minutes and then deposition was carried out at room temperature for two hours. The appearance of the film changed from lemon yellow to bright yellow as the deposition time increased. The sample was characterized for its structural and optical properties. XRD profile showed the polycrystalline behavior of the film with mixed phases having crystallite size of 17 nm. The surface morphology of the films exhibited uniformly distributed honey comb like structures. The film appeared to be smooth and the value of extinction coefficient was negligible. Optical measurements showed that the film has more than 80% transmission in the visible region. The direct band gap energy was 2.47eV. This method is highly suitable for the synthesis of crystalline and transparent indium sulfide thin films and can be used for various photo voltaic applications.

  2. Effect of Different Catalyst Deposition Technique on Aligned Multiwalled Carbon Nanotubes Grown by Thermal Chemical Vapor Deposition

    Directory of Open Access Journals (Sweden)

    Mohamed Shuaib Mohamed Saheed

    2014-01-01

    Full Text Available The paper reported the investigation of the substrate preparation technique involving deposition of iron catalyst by electron beam evaporation and ferrocene vaporization in order to produce vertically aligned multiwalled carbon nanotubes array needed for fabrication of tailored devices. Prior to the growth at 700°C in ethylene, silicon dioxide coated silicon substrate was prepared by depositing alumina followed by iron using two different methods as described earlier. Characterization analysis revealed that aligned multiwalled carbon nanotubes array of 107.9 µm thickness grown by thermal chemical vapor deposition technique can only be achieved for the sample with iron deposited using ferrocene vaporization. The thick layer of partially oxidized iron film can prevent the deactivation of catalyst and thus is able to sustain the growth. It also increases the rate of permeation of the hydrocarbon gas into the catalyst particles and prevents agglomeration at the growth temperature. Combination of alumina-iron layer provides an efficient growth of high density multiwalled carbon nanotubes array with the steady growth rate of 3.6 µm per minute for the first 12 minutes and dropped by half after 40 minutes. Thicker and uniform iron catalyst film obtained from ferrocene vaporization is attributed to the multidirectional deposition of particles in the gaseous form.

  3. Influence of substrate metal alloy type on the properties of hydroxyapatite coatings deposited using a novel ambient temperature deposition technique.

    Science.gov (United States)

    Barry, J N; Cowley, A; McNally, P J; Dowling, D P

    2014-03-01

    Hydroxyapatite (HA) coatings are applied widely to enhance the level of osteointegration onto orthopedic implants. Atmospheric plasma spray (APS) is typically used for the deposition of these coatings; however, HA crystalline changes regularly occur during this high-thermal process. This article reports on the evaluation of a novel low-temperature (alloy substrates. This study addresses the suitability of the CoBlast technique for the deposition of HA coatings on a number of alternative metal alloys utilized in the fabrication of orthopedic devices. In addition to titanium grade 5, both cobalt chromium and stainless steel 316 were investigated. In this study, HA coatings were deposited using both the CoBlast and the plasma sprayed techniques, and the resultant HA coating and substrate properties were evaluated and compared. The CoBlast-deposited HA coatings were found to present similar surface morphologies, interfacial properties, and composition irrespective of the substrate alloy type. Coating thickness however displayed some variation with the substrate alloy, ranging from 2.0 to 3.0 μm. This perhaps is associated with the electronegativity of the metal alloys. The APS-treated samples exhibited evidence of both coating, and significantly, substrate phase alterations for two metal alloys; titanium grade 5 and cobalt chrome. Conversely, the CoBlast-processed samples exhibited no phase changes in the substrates after depositions. The APS alterations were attributed to the brief, but high-intensity temperatures experienced during processing. Copyright © 2013 Wiley Periodicals, Inc.

  4. Improved CVD Techniques for Depositing Passivation Layers of ICs

    Science.gov (United States)

    1975-10-01

    Gases. ... 216 Effects of Substrate Surface . . . . . . eco . yt . . . . . 216 Applicability of Results to Other CVD Reco ytms .. . 216 Post-Deposition...October 11, - eCo .,1,Nolp.4,ardNok, ZE6 1970). 193) 363. D. S. Zoroglu and L. E. Cak EE~rf5 358, Staff Article, "How Phosphorus Abets IC Destruc- Eeto...lmghthroghpt, b sipleIn these reactors, thke substrate wafers are placed and qafv to operate, and easy to maintainl. Tile captal cst o theo lkptlnt

  5. Coating of ceramic powders by chemical vapor deposition techniques (CVD)

    International Nuclear Information System (INIS)

    Haubner, R.; Lux, B.

    1997-01-01

    New ceramic materials with selected advanced properties can be designed by coating of ceramic powders prior to sintering. By variation of the core and coating material a large number of various powders and ceramic materials can be produced. Powders which react with the binder phase during sintering can be coated with stable materials. Thermal expansion of the ceramic materials can be adjusted by varying the coating thickness (ratio core/layer). Electrical and wear resistant properties can be optimized for electrical contacts. A fluidized bed reactor will be designed which allow the deposition of various coatings on ceramic powders. (author)

  6. Uranium solution mining cost estimating technique: means for rapid comparative analysis of deposits

    International Nuclear Information System (INIS)

    Anon.

    1978-01-01

    Twelve graphs provide a technique for determining relative cost ranges for uranium solution mining projects. The use of the technique can provide a consistent framework for rapid comparative analysis of various properties of mining situations. The technique is also useful to determine the sensitivities of cost figures to incremental changes in mining factors or deposit characteristics

  7. The Development of a Differential Deposition Technique for Figure Correction in Grazing Incidence Optics

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose the development of a physical-vapor-deposition coating technique to correct residual figure errors in grazing-incidence optics. The process involves...

  8. Nanophotonic Fabrication Self-Assembly and Deposition Techniques

    CERN Document Server

    Yatsui, Takashi

    2012-01-01

    Nanophotonics, a novel optical technology, utilizes the local interaction between nanometric particles via optical near fields. The optical near fields are the elementary surface excitations on nanometric particles, i.e. dressed photons that carry material energy. Of the variety of qualitative innovations in optical technology realized by nanophotonics, this books focuses on fabrication. To fabricate nano-scale photonic devices with nanometer-scale controllability in size and position, we developed a self-assembly method for size- and position-controlled ultra-long nanodot chains using a novel effect of near-field optical desorption. A novel deposition and etching scheme under nonresonant conditions is also demonstrated and its origin is reviewed.

  9. Structural characterization of the nickel thin film deposited by glad technique

    Directory of Open Access Journals (Sweden)

    Potočnik J.

    2013-01-01

    Full Text Available In this work, a columnar structure of nickel thin film has been obtained using an advanced deposition technique known as Glancing Angle Deposition. Nickel thin film was deposited on glass sample at the constant emission current of 100 mA. Glass sample was positioned 15 degrees with respect to the nickel vapor flux. The obtained nickel thin film was characterized by Force Modulation Atomic Force Microscopy and by Scanning Electron Microscopy. Analysis indicated that the formation of the columnar structure occurred at the film thickness of 1 μm, which was achieved for the deposition time of 3 hours. [Projekat Ministarstva nauke Republike Srbije, br. III45005

  10. Silicon doping techniques using chemical vapor dopant deposition

    NARCIS (Netherlands)

    Popadic, M.

    2009-01-01

    Ultrashallow junctions are essential for the achievement of superior transistor performance, both in MOSFET and bipolar transistors. The stringent demands require state-of-the-art fabrication techniques. At the same time, in a different context, the accurate fabrication of various n type doping

  11. A study of the deposition process of multilayer coatings on the inner tube surface with the pulsed laser deposition technique

    Energy Technology Data Exchange (ETDEWEB)

    Lozovan, A.A., E-mail: loz-plasma@ya.ru; Alexandrova, S.S.; Mishnev, M.A.; Prishepov, S.V.

    2014-02-15

    Highlights: • Submitted laser bench for coatings, deposited on the inner surfaces of tubes by PLD. • Sprayed multilayered Ti/TiN coatings on the inner surfaces of tubes of small diameter. • We study this of coatings by method RBS and X-ray fluorescence spectroscopy (TXRF). • Shown a significant mixing of the layers thickness of 90 μm. -- Abstract: The multilayer Ti/TiN/Ti coatings (consisting of nano-scale layers) on the inner surface of stainless steel tubes of small diameter were studied. The coatings were deposited by using the pulsed laser deposition (PLD) technique (in the reactive and non-reactive deposition modes). The coatings were analyzed using the X-ray fluorescence analysis with total external reflection (TXRF) and the Rutherford backscattering spectroscopy (RBS). It was found that the deposition of multilayer Ti/TiN/Ti coatings leads to the essential mixing of coating layers due to sputtering of coatings with fast atoms and ions from the laser plume and the evaporation of the coating under the laser radiation reflected from the target surface.

  12. Deposition techniques for the preparation of thin film nuclear targets

    International Nuclear Information System (INIS)

    Muggleton, A.H.F.

    1987-07-01

    This review commences with a brief description of the basic principles that regulate vacuum evaporation and the physical processes involved in thin film formation, followed by a description of the experimental methods used. The principle methods of heating the evaporant are detailed and the means of measuring and controlling the film thickness are elucidated. Types of thin film nuclear targets are considered and various film release agents are listed. Thin film nuclear target behaviour under ion-bombardment is described and the dependence of nuclear experimental results upon target thickness and uniformity is outlined. Special problems associated with preparing suitable targets for lifetime measurements are discussed. The causes of stripper-foil thickening and breaking under heavy-ion bombardment are considered. A comparison is made between foils manufactured by a glow discharge process and those produced by vacuum sublimation. Consideration is given to the methods of carbon stripper-foil manufacture and to the characteristics of stripper-foil lifetimes are considered. Techniques are described that have been developed for the fabrication of special targets, both from natural and isotopically enriched material, and also of elements that are either chemically unstable, or thermally unstable under irradiation. The reduction of metal oxides by the use of hydrogen or by utilising a metallothermic technique, and the simultaneous evaporation of reduced rare earth elements is described. A comprehensive list of the common targets is presented

  13. A review of basic phenomena and techniques for sputter-deposition of high temperature superconducting films

    Energy Technology Data Exchange (ETDEWEB)

    Auciello, O. (Microelectronics Center of North Carolina, Research Triangle Park, NC (USA) North Carolina State Univ., Raleigh, NC (USA). Dept. of Materials Science and Engineering); Ameen, M.S.; Kingon, A.I.; Lichtenwalner, D.J. (North Carolina State Univ., Raleigh, NC (USA). Dept. of Materials Science and Engineering); Krauss, A.R. (Argonne National Lab., IL (USA))

    1990-01-01

    The processes involved in plasma and ion beam sputter-deposition of high temperature superconducting thin films are critically reviewed. Recent advances in the development of these techniques are discussed in relation to basic physical phenomena, specific to each technique, which must be understood before high quality films can be produced. Control of film composition is a major issue in sputter-deposition of multicomponent materials. Low temperature processing of films is a common goal for each technique, particularly in relation to integrating high temperature superconducting films with the current microelectronics technology. It has been understood for some time that for Y{sub 1}Ba{sub 2}Cu{sub 3}O{sub 7} deposition, the most intensely studied high-{Tc} compound, incorporation of sufficient oxygen into the film during deposition is necessary to produce as-deposited superconducting films at relatively substrate temperatures. Recent results have shown that with the use of suitable buffer layers, high quality Y{sub 1}Ba{sub 2}Cu{sub 3}O{sub 7} sputtered films can be obtained on Si substrates without the need for post-deposition anneal processing. This review is mainly focussed on issues related to sputter-deposition of Y{sub 1}Ba{sub 2}Cu{sub 3}O{sub 7} thin films, although representative results concerning the bismuth and thallium based compounds are included. 143 refs., 11 figs.

  14. Pulsed laser deposition: the road to hybrid nanocomposites coatings and novel pulsed laser adaptive technique.

    Science.gov (United States)

    Serbezov, Valery

    2013-01-01

    The applications of Pulsed Laser Deposition (PLD) for producing nanoparticles, nanostructures and nanocomposites coatings based on recently developed laser ablating techniques and their convergence are being reviewed. The problems of in situ synthesis of hybrid inorganic-organic nanocomposites coatings by these techniques are being discussed. The novel modification of PLD called Pulsed Laser Adaptive Deposition (PLAD) technique is presented. The in situ synthesized inorganic/organic nanocomposites coatings from Magnesium (Mg) alloy/Rhodamine B and Mg alloy/ Desoximetasone by PLAD are described. The trends, applications and future development of discussed patented methods based on the laser ablating technologies for producing hybrid nanocomposite coatings have also been discussed in this review.

  15. Optimisation of the electroless metal deposition technique for use in photonics

    DEFF Research Database (Denmark)

    Malureanu, Radu; Andryieuski, Andrei; Lavrinenko, Andrei

    2010-01-01

    enhanced chemical vapour deposition (PECVD) technique [5]. Even if the results are promising, the parameter space of such technique is huge thus making it almost impossible to avoid the local optimum points. In this work we present an optimised technique for 3D deposition of metals. Our technique is based...... on the well known Tollen’s test for detecting the presence of aldehyde groups inside a solution [6]. By optimising the concentration and the ratio of the chemicals involved, one can obtain very smooth and thin Ag layers (see figure 1a). In the same time, since the reaction takes place in solution......, it is by definition isotropic and thus suitable for depositing the metal on complex structures (see figure 1b)....

  16. Nanocrystalline CuInSSe thin films by chemical bath deposition technique

    Energy Technology Data Exchange (ETDEWEB)

    Shrotriya, Vipin, E-mail: vipinshrotriya@gmail.com; Rajaram, P., E-mail: prajaram@ymail.com [School of Studies in Physics, Jiwaji University, Gwalior (M.P.)-474011 (India)

    2016-05-06

    Crystalline CuInSSe thin films have been deposited on glass substrate by chemical bath deposition technique. The CuCl{sub 2}, InCl{sub 3}, thiourea and SeO{sub 2} were used as source materials for the Cu{sup 2+}, In{sup 3+}, S{sup 2−} and Se{sup 2−} ions and the Cu/In ratio was kept at 1.0. EDC was used as a complexing agent. The XRD, Scanning Electron Microscope (SEM), Energy Dispersive Analysis of X-Ray (EDAX) and Optical transmission studies were used for structural analysis, surface morphology, elemental analysis and optical band gap, of the grown thin films respectively. The deposition parameters such as pH, deposition temperature and deposition time were optimized.

  17. Measurements of aerosol particle dry deposition velocity using the relaxed eddy accumulation technique

    OpenAIRE

    Grönholm, Tiia; Aalto, Pasi P.; Hiltunen, Veijo; Rannik, Üllar; Rinne, Janne; Laakso, Lauri; Hyvönen, Saara; Vesala, Timo; Kulmala, Markku

    2011-01-01

    The continuous measurements of aerosol particle deposition velocity have been performed from January 2004 to January 2005 using a REA technique with dynamic deadband. We measured aerosol particle deposition velocity in the size range of 10–150 nanometer with 5–10 nanometer steps using differential mobility analyser for sizing. We were able to measure two size classes simultaneously. One size class was changed at one month intervals, another we kept constant at 30 nm to investigate the effect ...

  18. Overlayer structure of subphthalocyanine derivative deposited on Au (111) surface by a spray-jet technique

    International Nuclear Information System (INIS)

    Suzuki, Hitoshi; Yamada, Toshiki; Miki, Hideki; Mashiko, Shinro

    2006-01-01

    A new spray-jet technique was used to deposit subphthalocyanine derivative (chloro[tri-tert-butyl subphthalocyaninato]boron (TBSubPc)) on Au (111) surface in an ultra-high vacuum (UHV) chamber. The deposited molecular overlayer was observed with UHV scanning tunneling microscopy (STM) at 77 K. The STM images showed that TBSubPc molecules formed a stripe pattern with regular spacing, indicating that they preferentially adsorbed along the herringbone structure of the Au (111) surface. This behavior was very similar to that of TBSubPc molecules deposited by thermal evaporation

  19. Growth of cluster assembled ZnO film by nanocluster beam deposition technique

    Energy Technology Data Exchange (ETDEWEB)

    Halder, Nilanjan [Department of Physics, Manipal University Jaipur, Jaipur-303007 (India)

    2015-06-24

    ZnO is considered as one of the most promising material for optoelectronic devices. The present work emphasizes production of cluster assembled ZnO films by a UHV nanocluster beam deposition technique where the nanoclusters were produced in a laser vaporization cluster source. The microstructural and the optical properties of the ZnO nanocluster film deposited were investigated. As the wet chemical processes are not compatible with current solid state methods of device fabrication, therefore alternative UHV technique described in the paper is the need of the hour.

  20. A MECHANISTIC MODEL FOR PARTICLE DEPOSITION IN DIESEL PARTICLUATE FILTERS USING THE LATTICE-BOLTZMANN TECHNIQUE

    Energy Technology Data Exchange (ETDEWEB)

    Stewart, Mark L.; Rector, David R.; Muntean, George G.; Maupin, Gary D.

    2004-08-01

    Cordierite diesel particulate filters (DPFs) offer one of the most promising aftertreatment technologies to meet the quickly approaching EPA 2007 heavy-duty emissions regulations. A critical, yet poorly understood, component of particulate filter modeling is the representation of soot deposition. The structure and distribution of soot deposits upon and within the ceramic substrate directly influence many of the macroscopic phenomenon of interest, including filtration efficiency, back pressure, and filter regeneration. Intrinsic soot cake properties such as packing density and permeability coefficients remain inadequately characterized. The work reported in this paper involves subgrid modeling techniques which may prove useful in resolving these inadequacies. The technique involves the use of a lattice Boltzmann modeling approach. This approach resolves length scales which are orders of magnitude below those typical of a standard computational fluid dynamics (CFD) representation of an aftertreatment device. Individual soot particles are introduced and tracked as they move through the flow field and are deposited on the filter substrate or previously deposited particles. Electron micrographs of actual soot deposits were taken and compared to the model predictions. Descriptions of the modeling technique and the development of the computational domain are provided. Preliminary results are presented, along with some comparisons with experimental observations.

  1. Handbook of thin film deposition processes and techniques principles, methods, equipment and applications

    CERN Document Server

    Seshan, Krishna

    2002-01-01

    New second edition of the popular book on deposition (first edition by Klaus Schruegraf) for engineers, technicians, and plant personnel in the semiconductor and related industries. This book traces the technology behind the spectacular growth in the silicon semiconductor industry and the continued trend in miniaturization over the last 20 years. This growth has been fueled in large part by improved thin film deposition techniques and the development of highly specialized equipment to enable this deposition. The book includes much cutting-edge material. Entirely new chapters on contamination and contamination control describe the basics and the issues-as feature sizes shrink to sub-micron dimensions, cleanliness and particle elimination has to keep pace. A new chapter on metrology explains the growth of sophisticated, automatic tools capable of measuring thickness and spacing of sub-micron dimensions. The book also covers PVD, laser and e-beam assisted deposition, MBE, and ion beam methods to bring together a...

  2. A comparative study of CdS thin films deposited by different techniques

    Energy Technology Data Exchange (ETDEWEB)

    Pérez-Hernández, G., E-mail: german.perez@ujat.mx [Universidad Juárez Autónoma de Tabasco, Avenida Universidad s/n, Col. Magisterial, Villahermosa, Tabasco 86040 (Mexico); Pantoja-Enríquez, J. [Centro de Investigación y Desarrollo Tecnológico en Energías Renovables, UNICACH, Libramiento Norte No 1150, Tuxtla Gutiérrez, Chiapas 29039 (Mexico); Escobar-Morales, B. [Instituto Tecnológico de Cancún, Avenida Kábah Km 3, Cancún, Quintana Roo 77500 (Mexico); Martinez-Hernández, D.; Díaz-Flores, L.L.; Ricardez-Jiménez, C. [Universidad Juárez Autónoma de Tabasco, Avenida Universidad s/n, Col. Magisterial, Villahermosa, Tabasco 86040 (Mexico); Mathews, N.R.; Mathew, X. [Centro de Investigación en Energía, Universidad Nacional Autónoma de México, Temixco, Morelos 62580 (Mexico)

    2013-05-01

    Cadmium sulfide thin-films were deposited on glass slides and SnO{sub 2}:F coated glass substrates by chemical bath deposition, sputtering and close-spaced sublimation techniques. The films were studied for the structural and opto-electronic properties after annealing in an ambient identical to that employed in the fabrication of CdTe/CdS devices. Quantum efficiency of the CdTe/CdS solar cells fabricated with CdS buffer films prepared by the three methods were investigated to understand the role of CdS film preparation method on the blue response of the devices. The higher blue response observed for the devices fabricated with chemical bath deposited CdS film is discussed. - Highlights: ► CdS films were prepared by different techniques. ► Role of CdS on the blue response of device was studied. ► Structural and optical properties of CdS were analyzed. ► Chemically deposited CdS has high blue transmittance. ► CdS deposition method influences diffusion of S and Te.

  3. Microfluidic Genipin Deposition Technique for Extended Culture of Micropatterned Vascular Muscular Thin Films.

    Science.gov (United States)

    Hald, Eric S; Steucke, Kerianne E; Reeves, Jack A; Win, Zaw; Alford, Patrick W

    2015-06-26

    The chronic nature of vascular disease progression requires the development of experimental techniques that simulate physiologic and pathologic vascular behaviors on disease-relevant time scales. Previously, microcontact printing has been used to fabricate two-dimensional functional arterial mimics through patterning of extracellular matrix protein as guidance cues for tissue organization. Vascular muscular thin films utilized these mimics to assess functional contractility. However, the microcontact printing fabrication technique used typically incorporates hydrophobic PDMS substrates. As the tissue turns over the underlying extracellular matrix, new proteins must undergo a conformational change or denaturing in order to expose hydrophobic amino acid residues to the hydrophobic PDMS surfaces for attachment, resulting in altered matrix protein bioactivity, delamination, and death of the tissues. Here, we present a microfluidic deposition technique for patterning of the crosslinker compound genipin. Genipin serves as an intermediary between patterned tissues and PDMS substrates, allowing cells to deposit newly-synthesized extracellular matrix protein onto a more hydrophilic surface and remain attached to the PDMS substrates. We also show that extracellular matrix proteins can be patterned directly onto deposited genipin, allowing dictation of engineered tissue structure. Tissues fabricated with this technique show high fidelity in both structural alignment and contractile function of vascular smooth muscle tissue in a vascular muscular thin film model. This technique can be extended using other cell types and provides the framework for future study of chronic tissue- and organ-level functionality.

  4. Comparison of the columnar-thin-film and vacuum-metal-deposition techniques to develop sebaceous fingermarks on nonporous substrates.

    Science.gov (United States)

    Williams, Stephanie F; Pulsifer, Drew P; Shaler, Robert C; Ramotowski, Robert S; Brazelle, Shelly; Lakhtakia, Akhlesh

    2015-03-01

    Both the columnar-thin-film (CTF) and the vacuum-metal-deposition (VMD) techniques for visualizing sebaceous fingermarks require the deposition of a material thereon in a vacuum chamber. Despite that similarity, there are many differences between the two techniques. The film deposited with the CTF technique has a columnar morphology, but the film deposited with the VMD technique comprises discrete islands. A split-print methodology on a variety of fingermarked substrates was used to determine that the CTF technique is superior for developing fingermarks on clear sandwich bags and partial bloody fingermarks on stainless steel. Both techniques are similar in their ability to develop fingermarks on glass but the CTF technique yields higher contrast. The VMD technique is superior for developing fingermarks on white grocery bags and the smooth side of Gloss Finish Scotch Multitask(™) tape. Neither technique worked well for fingermarks on black garbage bags. © 2014 American Academy of Forensic Sciences.

  5. Development of plasma assisted thermal vapor deposition technique for high-quality thin film

    Science.gov (United States)

    Lee, Kang-Il; Choi, Yong Sup; Park, Hyun Jae

    2016-12-01

    The novel technique of Plasma-Assisted Vapor Deposition (PAVD) is developed as a new deposition method for thin metal films. The PAVD technique yields a high-quality thin film without any heating of the substrate because evaporated particles acquire energy from plasma that is confined to the inside of the evaporation source. Experiments of silver thin film deposition have been carried out in conditions of pressure lower than 10-3 Pa. Pure silver plasma generation is verified by the measurement of the Ag-I peak using optical emission spectroscopy. A four point probe and a UV-VIS spectrophotometer are used to measure the electrical and optical properties of the silver film that is deposited by PAVD. For an ultra-thin silver film with a thickness of 6.5 nm, we obtain the result of high-performance silver film properties, including a sheet resistance visible-range transmittance >75%. The PAVD-film properties show a low sheet resistance of 30% and the same transmittance with conventional thermal evaporation film. In the PAVD source, highly energetic particles and UV from plasma do not reach the substrate because the plasma is completely shielded by the optimized nozzle of the crucible. This new PAVD technique could be a realistic solution to improve the qualities of transparent electrodes for organic light emission device fabrication without causing damage to the organic layers.

  6. Parallel deposition of size-selected clusters: a novel technique for studying size-selectivity on the atomic scale.

    Science.gov (United States)

    Luo, Yuan; Seo, Hyun Ook; Beck, Martin; Proch, Sebastian; Kim, Young Dok; Ganteför, Gerd

    2014-05-28

    A new size-selected cluster deposition technique referred to as "parallel-deposition" is presented. An ion beam of multi-sized Aun clusters was spatially separated into individual cluster sizes by utilizing a Wien filter and the clusters spatially separated based on their atomic sizes were simultaneously deposited on a SiO2/Si(100) substrate. Parallel-deposited Aun clusters (n = 6, 7, and 8) on the SiO2/Si(100) substrate showed even-odd oxidation behaviour upon exposure to an atomic oxygen atmosphere, demonstrating the potential of this new technique to study the size-dependent properties of deposited clusters in various research fields.

  7. Deposition

    International Nuclear Information System (INIS)

    1984-01-01

    Monitoring of radionuclide contents in rainwater is a useful way to keep a check on any change in the external radiation dose caused by the deposited material. Thus analuses of 3 H, 89 Sr and 90 Sr as well as 137 Cs and other gamma radionuclide contents in deposition were continued both nationwide and in the vicinities of the nuclear power stations at Loviisa and Olkiluoto. The deposition of 90 Sr and 137 Cs was lower than in previous years, being only a small fraction of the highest deposition values measured in 1983. The tritium concentrations were also lower than in 1982. The total annual deposition of tritium at different sampling stations varied from 1.7 kBq/m 2 to 2.9 kBq/m 2

  8. Lipase immobilization for catalytic applications obtained using fumed silica deposited with MAPLE technique

    Science.gov (United States)

    Bloisi, Francesco; Califano, Valeria; Perretta, Giuseppe; Nasti, Libera; Aronne, Antonio; Di Girolamo, Rocco; Auriemma, Finizia; De Rosa, Claudio; Vicari, Luciano R. M.

    2016-06-01

    Lipases are enzymes used for catalyzing reactions of acylglycerides in biodiesel production from lipids, where enzyme immobilization on a substrate is required. Silica nanoparticles in different morphologies and configurations are currently used in conjunction with biological molecules for drug delivery and catalysis applications, but up to date their use for triglycerides has been limited by the large size of long-chain lipid molecules. Matrix assisted pulsed laser evaporation (MAPLE), a laser deposition technique using a frozen solution/suspension as a target, is widely used for deposition of biomaterials and other delicate molecules. We have carried out a MAPLE deposition starting from a frozen mixture containing fumed silica and lipase in water. Deposition parameters were chosen in order to increase surface roughness and to promote the formation of complex structures. Both the target (a frozen thickened mixture of nanoparticles/catalyst in water) and the deposition configuration (a small target to substrate distance) are unusual and have been adopted in order to increase surface contact of catalyst and to facilitate access to long-chain molecules. The resulting innovative film morphology (fumed silica/lipase cluster level aggregation) and the lipase functionality (for catalytic biodiesel production) have been studied by FESEM, FTIR and transesterification tests.

  9. The Influence of Various Deposition Techniques on the Photoelectrochemical Properties of the Titanium Dioxide Thin Fil

    Czech Academy of Sciences Publication Activity Database

    Morozová, Magdalena; Klusoň, Petr; Dzik, P.; Veselý, M.; Baudyš, M.; Krýsa, J.; Šolcová, Olga

    2013-01-01

    Roč. 65, č. 3 (2013), s. 452-458 ISSN 0928-0707 R&D Projects: GA TA ČR TA01020804 Grant - others:GA ČR(CZ) GP104/09/P165 Institutional support: RVO:67985858 Keywords : titanium dioxide * photoelectrochemical properties * deposition techniques Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 1.547, year: 2013

  10. The influence of inhalation technique on Technegas particle deposition and image appearance in normal volunteers

    International Nuclear Information System (INIS)

    Lloyd, J.J.; James, J.M.; Shields, R.A.; Testa, H.J.

    1994-01-01

    The aim of this work was to investigate the influence of inhalation technique on Technegas image quality and on fractional particle deposition. This was investigated in six normal volunteers using three different types of breathing pattern. Fractional deposition was determined by analysis of dynamic gamma camera images acquired during Technegas administration. Static lung images were subsequently acquired and assessed independently by three experienced observers. High-quality images were obtained in all cases although slight differences were noted. The images produced using a slow deep inspiration with a breath hold (i.e. the standard method) were of more uniform texture and also had the least gradient in activity from apex to base. The converse was true for a rapid inhalation technique. The average fractional deposition per breath was 55%, but this varied between individuals and with breathing pattern, being most influenced by the total duration of a breath. We conclude that for patient studies the standard inhalation technique is best, although variation to suit individual patients would be acceptable. (orig./MG)

  11. Instantly AgNPs deposition through facile solventless technique for poly-functional cotton fabrics.

    Science.gov (United States)

    Emam, Hossam E; Saleh, N H; Nagy, Khaled S; Zahran, M K

    2016-03-01

    Nowadays, functional clothes are employed for human body protection in addition to be fashionable clothes. Hence functionalization of clothes increases the attention of scientists and business. In the current study, poly-functional cotton fabric was carried out by instantly deposition of AgNPs using two solventless techniques namely; sorption and padding. Sorption technique was exhibited extremely high efficiency than padding one by ca. 10 times. By using the same concentrations of AgNO3, Ag content was ranged 69.3-6094.8 mg/kg and 33.8-609.3 mg/kg for sorption and padding, respectively. After AgNPs deposition, fabrics color was turned to gray-reddish yellow. By applying 5912.3 mgAg/kg fabric, bacterial reduction and UPF value were reached 99% and 12.59. Bacterial reduction and UPF were lessened to 90% and 10.19 after 20 washings. These findings proved that the direct AgNPs deposition into cotton using solventless/sorption technique is applicable in manufacturing of antibacterial/UV resistant fabrics with acquired decorative color. Copyright © 2015 Elsevier B.V. All rights reserved.

  12. HfO2 as gate dielectric on Ge: Interfaces and deposition techniques

    International Nuclear Information System (INIS)

    Caymax, M.; Van Elshocht, S.; Houssa, M.; Delabie, A.; Conard, T.; Meuris, M.; Heyns, M.M.; Dimoulas, A.; Spiga, S.; Fanciulli, M.; Seo, J.W.; Goncharova, L.V.

    2006-01-01

    To fabricate MOS gate stacks on Ge, one can choose from a multitude of metal oxides as dielectric material which can be deposited by many chemical or physical vapor deposition techniques. As a few typical examples, we will discuss here the results from atomic layer deposition (ALD), metal organic CVD (MOCVD) and molecular beam deposition (MBD) using HfO 2 /Ge as materials model system. It appears that a completely interface layer free HfO 2 /Ge combination can be made in MBD, but this results in very bad capacitors. The same bad result we find if HfGe y (Hf germanides) are formed like in the case of MOCVD on HF-dipped Ge. A GeO x interfacial layer appears to be indispensable (if no other passivating materials are applied), but the composition of this interfacial layer (as determined by XPS, TOFSIMS and MEIS) is determining for the C/V quality. On the other hand, the presence of Ge in the HfO 2 layer is not the most important factor that can be responsible for poor C/V, although it can still induce bumps in C/V curves, especially in the form of germanates (Hf-O-Ge). We find that most of these interfacial GeO x layers are in fact sub-oxides, and that this could be (part of) the explanation for the high interfacial state densities. In conclusion, we find that the Ge surface preparation is determining for the gate stack quality, but it needs to be adapted to the specific deposition technique

  13. A lithium depth-marker technique for rapid erosion and deposition measurements

    International Nuclear Information System (INIS)

    Sullivan, R.M.; Pang, A.; Martinez-Sanchez, M.; Whyte, D.G.

    2014-01-01

    Highlights: • Rutherford backscattering spectrometry (RBS) to determine the change in depth. • Rutherford backscattering spectrometry (RBS) to determine the change in depth. • Rutherford backscattering spectrometry (RBS) to determine the change in depth. -- Abstract: A novel, high-resolution technique has been developed for the measurement of erosion and deposition in solid material surfaces. The technique uses a combination of nuclear reaction analysis (NRA) and Rutherford backscattering spectrometry (RBS) to determine the change in depth of a previously implanted marker layer consisting of 7 Li. A scoping study shows that 7 Li is an ideal marker candidate due to a high Q (∼18 MeV) nuclear reaction, 7 Li(p,α) 4 He. Net erosion or deposition is measured by NRA of modified alpha energy passing through the bulk material. The reaction’s high cross-section provides for the fast time resolution needed to measure erosion from high flux plasmas, and a highly penetrating proton beam provides for a large range of erosion/deposition measurements. Additionally, the implantation of low-Z Li leads to relatively low vacancy concentrations in the solid material due to implantation. This technique thus provides greater assurance that the measured erosion rate is indicative of the solid material: due to both the low vacancy production and the fact that no films or deposits are involved. Validation was performed by comparing the measured and predicted amount of erosion based on previously measured sputtering yields; the two were found to agree, within the uncertainty of the experiment. The depth resolution of the techniques is ∼60 nm at a net erosion depth of about 1 μm. The benefits of this technique are summarized as: short time scales (minutes) to obtain results, the marker layer can be used in any solid material, greater assurance that the measured erosion is indicative of the unperturbed solid material, and the continuous monitoring of the surface composition for

  14. Synthesis of Colloidal ZnO Nanoparticles and Deposit of Thin Films by Spin Coating Technique

    Directory of Open Access Journals (Sweden)

    Jose Alberto Alvarado

    2013-01-01

    Full Text Available ZnO colloidal nanoparticles were synthesized, the average size of these nanoparticles is around 25 nm with hexagonal form. It was noted that stabilization depends directly on the purifying process; in this work we do not change the nature of the solution as a difference from Meulekamp's method, and we do not use any alkanes to remove the byproducts; only a centrifuge to remove those ones was used, thereby the stabilization increases up to 24 days. It is observed from the results that only three times of washing is enough to prevent the rapid aging process. The effect of annealing process on the composition, size, and geometrical shape of ZnO nanoparticles was studied in order to know whether the annealing process affects the crystallization and growth of the nanoparticles. After the synthesis, the colloidal nanoparticles were deposited by spin coating technique showing that the formed nanoparticles have no uniformly deposition pattern. But is possible to deposit those ones in glass substrates. A possible deposition process of the nanoparticles is proposed.

  15. Novel Optical Diagnostic Techniques for Studying Particle Deposition Upon Large Cylinders in a Sheared Suspension

    Science.gov (United States)

    Yoda, M.; Bailey, B. C.

    2000-01-01

    On a twelve-month voyage to Mars, one astronaut will require at least two tons of potable water and two tons of pure oxygen. Efficient, reliable fluid reclamation is therefore necessary for manned space exploration. Space habitats require a compact, flexible, and robust apparatus capable of solid-fluid mechanical separation over a wide range of fluid and particle densities and particle sizes. In space, centrifugal filtration, where particles suspended in fluid are captured by rotating fixed-fiber mat filters, is a logical candidate for mechanical separation. Non-colloidal particles are deposited on the fibers due to inertial impaction or direct interception. Since rotation rates are easily adjustable, inertial effects are the most practical way to control separation rates for a wide variety of multiphase mixtures in variable gravity environments. Understanding how fluid inertia and differential fluid-particle inertia, characterized by the Reynolds and Stokes numbers, respectively, affect deposition is critical in optimizing filtration in a microgravity environment. This work will develop non-intrusive optical diagnostic techniques for directly visualizing where and when non-colloidal particles deposit upon, or contact, solid surfaces: 'particle proximity sensors'. To model particle deposition upon a single filter fiber, these sensors will be used in ground-based experiments to study particle dynamics as in the vicinity of a large (compared with the particles) cylinder in a simply sheared (i.e., linearly-varying, zero-mean velocity profile) neutrally-buoyant, refractive-index matched solid-liquid suspension.

  16. Metallographic techniques for evaluation of Thermal Barrier Coatings produced by Electron Beam Physical Vapor Deposition

    International Nuclear Information System (INIS)

    Kelly, Matthew; Singh, Jogender; Todd, Judith; Copley, Steven; Wolfe, Douglas

    2008-01-01

    Thermal Barrier Coatings (TBC) produced by Electron Beam Physical Vapor Deposition (EB-PVD) are primarily applied to critical hot section turbine components. EB-PVD TBC for turbine applications exhibit a complicated structure of porous ceramic columns separated by voids that offers mechanical compliance. Currently there are no standard evaluation methods for evaluating EB-PVD TBC structure quantitatively. This paper proposes a metallographic method for preparing samples and evaluating techniques to quantitatively measure structure. TBC samples were produced and evaluated with the proposed metallographic technique and digital image analysis for columnar grain size and relative intercolumnar porosity. Incorporation of the proposed evaluation technique will increase knowledge of the relation between processing parameters and material properties by incorporating a structural link. Application of this evaluation method will directly benefit areas of quality control, microstructural model development, and reduced development time for process scaling

  17. Synthesis of conductive semi-transparent silver films deposited by a Pneumatically-Assisted Ultrasonic Spray Pyrolysis Technique

    International Nuclear Information System (INIS)

    Zaleta-Alejandre, E.; Balderas-Xicoténcatl, R.; Arrieta, M.L. Pérez; Meza-Rocha, A.N.; Rivera-Álvarez, Z.; Falcony, C.

    2013-01-01

    Highlights: • We deposited metallic silver films without post-deposition annealing. • The spray pyrolysis technique is of low cost and scalable for industrial applications. • We obtained deposition rate of 60 nm min −1 at 300 °C. • The average resistivity was 1E−7 Ω m. • Semi-transparent silver films were obtained at 350 °C and deposition time of 45 s. -- Abstract: The synthesis and characterization of nanostructured silver films deposited on corning glass by a deposition technique called Pneumatically-Assisted Ultrasonic Spray Pyrolysis are reported. Silver nitrate and triethanolamine were used as silver precursor and reducer agent, respectively. The substrate temperatures during deposition were in the range of 300–450 °C and the deposition times from 30 to 240 s. The deposited films are polycrystalline with cubic face-centered structure, and crystalline grain size less than 30 nm. Deposition rates up to 600 Å min −1 were obtained at substrate temperature as low as 300 °C. The electrical, optical, and morphological properties of these films are also reported. Semi-transparent conductive silver films were obtained at 350 °C with a deposition time of 45 s

  18. Synthesis of conductive semi-transparent silver films deposited by a Pneumatically-Assisted Ultrasonic Spray Pyrolysis Technique

    Energy Technology Data Exchange (ETDEWEB)

    Zaleta-Alejandre, E.; Balderas-Xicoténcatl, R. [Centro de Investigación y de Estudios Avanzados-IPN, Departamento de Física, , Apdo. Postal 14-470, Del, Gustavo A. Madero, C.P. 07000, México, D.F. (Mexico); Arrieta, M.L. Pérez [Universidad Autónoma de Zacatecas, Unidad Académica de Física, Calzada Solidaridad esq. Paseo, La Bufa s/n, C.P. 98060, Zacatecas, México (Mexico); Meza-Rocha, A.N.; Rivera-Álvarez, Z. [Centro de Investigación y de Estudios Avanzados-IPN, Departamento de Física, , Apdo. Postal 14-470, Del, Gustavo A. Madero, C.P. 07000, México, D.F. (Mexico); Falcony, C., E-mail: cfalcony@fis.cinvestav.mx [Centro de Investigación y de Estudios Avanzados-IPN, Departamento de Física, , Apdo. Postal 14-470, Del, Gustavo A. Madero, C.P. 07000, México, D.F. (Mexico)

    2013-10-01

    Highlights: • We deposited metallic silver films without post-deposition annealing. • The spray pyrolysis technique is of low cost and scalable for industrial applications. • We obtained deposition rate of 60 nm min{sup −1} at 300 °C. • The average resistivity was 1E−7 Ω m. • Semi-transparent silver films were obtained at 350 °C and deposition time of 45 s. -- Abstract: The synthesis and characterization of nanostructured silver films deposited on corning glass by a deposition technique called Pneumatically-Assisted Ultrasonic Spray Pyrolysis are reported. Silver nitrate and triethanolamine were used as silver precursor and reducer agent, respectively. The substrate temperatures during deposition were in the range of 300–450 °C and the deposition times from 30 to 240 s. The deposited films are polycrystalline with cubic face-centered structure, and crystalline grain size less than 30 nm. Deposition rates up to 600 Å min{sup −1} were obtained at substrate temperature as low as 300 °C. The electrical, optical, and morphological properties of these films are also reported. Semi-transparent conductive silver films were obtained at 350 °C with a deposition time of 45 s.

  19. Modulating the Optoelectronic Properties of Silver Nanowires Films: Effect of Capping Agent and Deposition Technique.

    Science.gov (United States)

    Lopez-Diaz, D; Merino, C; Velázquez, M M

    2015-11-11

    Silver nanowires 90 nm in diameter and 9 µm in length have been synthesized using different capping agents: polyvinyl pyrrolidone (PVP) and alkyl thiol of different chain lengths. The nanowire structure is not influenced by the displacement of PVP by alkyl thiols, although alkyl thiols modify the lateral aggregation of nanowires. We examined the effect of the capping agent and the deposition method on the optical and electrical properties of films prepared by Spray and the Langmuir-Schaefer methodologies. Our results revealed that nanowires capped with PVP and C8-thiol present the best optoelectronic properties. By using different deposition techniques and by modifying the nanowire surface density, we can modulate the optoelectronic properties of films. This strategy allows obtaining films with the optoelectronic properties required to manufacture touch screens and electromagnetic shielding.

  20. Modulating the Optoelectronic Properties of Silver Nanowires Films: Effect of Capping Agent and Deposition Technique

    Directory of Open Access Journals (Sweden)

    D. Lopez-Diaz

    2015-11-01

    Full Text Available Silver nanowires 90 nm in diameter and 9 µm in length have been synthesized using different capping agents: polyvinyl pyrrolidone (PVP and alkyl thiol of different chain lengths. The nanowire structure is not influenced by the displacement of PVP by alkyl thiols, although alkyl thiols modify the lateral aggregation of nanowires. We examined the effect of the capping agent and the deposition method on the optical and electrical properties of films prepared by Spray and the Langmuir-Schaefer methodologies. Our results revealed that nanowires capped with PVP and C8-thiol present the best optoelectronic properties. By using different deposition techniques and by modifying the nanowire surface density, we can modulate the optoelectronic properties of films. This strategy allows obtaining films with the optoelectronic properties required to manufacture touch screens and electromagnetic shielding.

  1. Determination of Redistribution of Erosion/Deposition Rate in Cultivated Area Using 137Cs Technique

    International Nuclear Information System (INIS)

    Nita Suhartini; Syamsul Abbas RAS; Barokah A; Ali Arman L

    2004-01-01

    The aim of the research is to determine the rate of redistribution of erosion/deposition in cultivated area. The application of 137 Cs technique was carried out at cultivated area in Bojong - Ciawi, with slope less than 10 o and slope length of about 2 km. A reference site was selected at the top of the slope, and this site is flat, open and covered with grass. Two sites in the cultivated area were selected as study site namely LU-I ( 15 x 25 ) m with the distance of 1000 m from the top, and LU-II (17.5 x 20) m with the distance of 1300 m from the top. Sampling of soil at reference site was done by using scraper (20 x 50) cm, while sampling at study site by using core sampling (di = 7 cm). Soil samples were brought to the laboratorium for preparation and analysis of 137 Cs content. Preparation are including of drying, weighing the total dry, sieving and crushing. Analysis of 137 Cs content was done using multi channel analyzer (MCA) that connected to high purity germanium (HPGe), at 661 keV, and the minimum counting time of 16 hours. To estimate the erosion/deposit rate, two mathematical model were used, namely Proportional Model (PM) and Mass Balance Model 1 (MBM1). The result for application of 137 Cs technique showed that MBM1 gives somewhat higher value for deposit rate and somewhat lower value for erosion than PM. Land use - I (LU-I) of Bojong - Ciawi was suffering from erosion with the erosion rate from 1 t/(ha.y) to 13 t/(ha.y), and LU-II has deposit rate from 1 t/(ha.y) to 50 t/(ha.y). (author)

  2. Nanocomposite metal amorphous-carbon thin films deposited by hybrid PVD and PECVD technique.

    Science.gov (United States)

    Teixeira, V; Soares, P; Martins, A J; Carneiro, J; Cerqueira, F

    2009-07-01

    Carbon based films can combine the properties of solid lubricating graphite structure and hard diamond crystal structure, i.e., high hardness, chemical inertness, high thermal conductivity and optical transparency without the crystalline structure of diamond. Issues of fundamental importance associated with nanocarbon coatings are reducing stress, improving adhesion and compatibility with substrates. In this work new nanocomposite coatings with improved toughness based in nanocrystalline phases of metals and ceramics embedded in amorphous carbon matrix are being developed within the frame of a research project: nc-MeNxCy/a-C(Me) with Me = Mo, Si, Al, Ti, etc. Carbide forming metal/carbon (Me/C) composite films with Me = Mo, W or Ti possess appropriate properties to overcome the limitation of pure DLC films. These novel coating architectures will be adopted with the objective to decrease residual stress, improve adherence and fracture toughness, obtain low friction coefficient and high wear-resistance. Nanocomposite DLC's films were deposited by hybrid technique using a PVD-Physically Vapor Deposition (magnetron sputtering) and Plasma Enhanced Chemical Vapor Deposition (PECVD), by the use of CH4 gas. The parameters varied were: deposition time, substrate temperature (180 degrees C) and dopant (Si + Mo) of the amorphous carbon matrix. All the depositions were made on silicon wafers and steel substrates precoated with a silicon inter-layer. The characterisation of the film's physico-mechanical properties will be presented in order to understand the influence of the deposition parameters and metal content used within the a-C matrix in the thin film properties. Film microstructure and film hybridization state was characterized by Raman Spectroscopy. In order to characterize morphology SEM and AFM will be used. Film composition was measured by Energy-Dispersive X-ray analysis (EDS) and by X-ray photoelectron spectroscopy (XPS). The contact angle for the produced DLC's on

  3. Tribological properties of CrN coatings deposited by nitro-chromizing treatment on AISI D2 steel

    Energy Technology Data Exchange (ETDEWEB)

    Durmaz, M., E-mail: mdurmaz@sakarya.edu.tr; Abakay, E.; Sen, U.; Sen, S. [Department of Metallurgical and Materials Engineering, Engineering Faculty, Sakarya University, Esentepe Campus, 54187 Sakarya (Turkey); Kilinc, B. [Department of Metallurgical and Materials Engineering, Institute of Arts and Sciences, Sakarya University, Esentepe Campus, 54187 Sakarya (Turkey)

    2015-03-30

    In this work, the wear test of uncoated and chromium nitride coated AISI D2 cold work tool steel against alumina ball realized at 0.1 m/s sliding speeds and under the loads of 2.5N, 5N and 10N. Steel samples were nitrided at 575°C for 8 h in the first step of the coating process, and then chromium nitride coating was performed thermo-reactive deposition technique (TRD) in a powder mixture consisting of ferro-chromium, ammonium chloride and alumina at 1000°C for 2 h. Nitro-chromized samples were characterized by X-Ray diffraction analysis (XRD), scanning electron microscopy (SEM), micro-hardness and ball on disk wear tests. The coating layer formed on the AISI D2 steel was compact and homogeneous. X-ray studies showed that the phase formed in the coated layer is Cr{sub 2}N. The depth of the layer was 8.15 µm. The average hardness of the layer was 2160±15 HV{sub 0.025}. For uncoated and chromium nitride materials, wear rate increased with increasing load. The results of friction coefficient and wear rate of the tested materials showed that the CrN coating presents the lowest results.

  4. Deposition of (ZnO:In) TCO Thin Film on Glass Substrate Using DC Sputtering Technique

    International Nuclear Information System (INIS)

    Wirjoadi; Yunanto

    2009-01-01

    The (ZnO:In) TCO film has been deposited on glass structure using DC sputtering technique. The objective of this research is to study the effect of time deposition, gas pressure, substrate temperature, impurity of In on the resistance, transmittance, micro structure and crystal structure of (ZnO:In) thin film, so that it can be used as a CIS solar cell. The ZnO main target and In pinhole target was bombarded by Ar ion, so that the Zn, O, In atoms were sputtered and form thin film of (ZnO:In) on glass substrate. The resistance were measured using digital ohm meter, the transmittance using UV-Vis, micro structure and thickness using SEM and the crystal structure using XRD. The experiment results, show that the minimum resistance is 0.334 kΩ this obtained at the process parameter on 75 min of time deposition, 5x10 -2 Torr of gas pressure, 225℃ of substrate temperature and 8% of content In. The maximum transmittance is 80% at the wave length in (400-900) nm, while the crystal structure of ZnO and In thin film were oriented at the plane ( 0 0 4 ); ( 2 0 2 ) and ( 3 0 1 ). The surface morphology were distributed homogeneously with the thickness of the thin film was in order of 0.41 µm. (author)

  5. Application of silver nanodendrites deposited on silicon in SERS technique for the trace analysis of paraquat

    Science.gov (United States)

    Cao Dao, Tran; Quynh Ngan Luong, Truc; Cao, Tuan Anh; Kieu, Ngoc Minh; Le, Van Vu

    2016-03-01

    In order to detect trace concentrations of organic or biological molecules by surface-enhanced Raman scattering (SERS) technique, the SERS-active substrates with high enhancement factor are required. The silver nanodendrites (AgNDs) are a growing class of such SERS-active substrates. This report presents the preliminary results of the trace detection of paraquat (PQ), a commonly used herbicide, with the use of SERS-active substrates, which have been made from AgNDs deposited on silicon. The AgNDs were produced either by electroless deposition, or by electrodeposition onto a silicon wafer, using aqueous solution of HF and AgNO3. It was observed that the silver dendrites are formed only when AgNO3 concentration is high enough. Next, it was found that with the additional assistance of an electric potential in the electrodeposition, the dendrites have grown up with the more perfect ramification. The AgNDs with more perfect branching gave the Raman spectrum of PQ with higher enhancement factor. More specifically, while the SERS-active substrates prepared from electrodeposited AgNDs were able to detect PQ with concentration as low as 0.01 ppm, the ones made from electroless deposited AgNDs could only detect PQ at concentration of hundreds times higher.

  6. Enhanced surface functionality via plasma modification and plasma deposition techniques to create more biologically relevant materials

    Science.gov (United States)

    Shearer, Jeffrey C.

    Functionalizing nanoparticles and other unusually shaped substrates to create more biologically relevant materials has become central to a wide range of research programs. One of the primary challenges in this field is creating highly functionalized surfaces without modifying the underlying bulk material. Traditional wet chemistry techniques utilize thin film depositions to functionalize nanomaterials with oxygen and nitrogen containing functional groups, such as --OH and --NHx. These functional groups can serve to create surfaces that are amenable to cell adhesion or can act as reactive groups for further attachment of larger structures, such as macromolecules or antiviral agents. Additional layers, such as SiO2, are often added between the nanomaterial and the functionalized coating to act as a barrier films, adhesion layers, and to increase overall hydrophilicity. However, some wet chemistry techniques can damage the bulk material during processing. This dissertation examines the use of plasma processing as an alternative method for producing these highly functionalized surfaces on nanoparticles and polymeric scaffolds through the use of plasma modification and plasma enhanced chemical vapor deposition techniques. Specifically, this dissertation will focus on (1) plasma deposition of SiO2 barrier films on nanoparticle substrates; (2) surface functionalization of amine and alcohol groups through (a) plasma co-polymerization and (b) plasma modification; and (3) the design and construction of plasma hardware to facilitate plasma processing of nanoparticles and polymeric scaffolds. The body of work presented herein first examines the fabrication of composite nanoparticles by plasma processing. SiOxC y and hexylamine films were coated onto TiO2 nanoparticles to demonstrate enhanced water dispersion properties. Continuous wave and pulsed allyl alcohol plasmas were used to produce highly functionalized Fe2 O3 supported nanoparticles. Specifically, film composition was

  7. Preparation of multilayered chitosan-based nanofibers by combination of electrospinning and layer-by-layer deposition techniques

    OpenAIRE

    Croisier, Florence; Aqil, Abdelhafid; Detrembleur, Christophe; Jérôme, Christine

    2009-01-01

    By combining electrospinning technique and layer-by-layer deposition, we produced a new material made of multilayered, chitosan-based nanofibers. Layer-by-layer (LBL) is a well known method for surface coating, based on electrostatic interactions. It enables the controllable deposition of a variety of polyions including synthetic and natural materials, with designable layer structure, defined wall thickness and size. Electrospinning (ESP) technique allows the fabrication of polymer fibers ra...

  8. Enhancement of the Electrical Conductivity and Interlaminar Shear Strength of CNT/GFRP Hierarchical Composite Using an Electrophoretic Deposition Technique

    Directory of Open Access Journals (Sweden)

    Amin Haghbin

    2017-09-01

    Full Text Available In this work, an electrophoretic deposition (EPD technique has been used for deposition of carbon nanotubes (CNTs on the surface of glass fiber textures (GTs to increase the volume conductivity and the interlaminar shear strength (ILSS of CNT/glass fiber-reinforced polymers (GFRPs composites. Comprehensive experimental studies have been conducted to establish the influence of electric field strength, CNT concentration in EPD suspension, surface quality of GTs, and process duration on the quality of deposited CNT layers. CNT deposition increased remarkably when the surface of glass fibers was treated with coupling agents. Deposition of CNTs was optimized by measuring CNT’s deposition mass and process current density diagrams. The effect of optimum field strength on CNT deposition mass is around 8.5 times, and the effect of optimum suspension concentration on deposition rate is around 5.5 times. In the optimum experimental setting, the current density values of EPD were bounded between 0.5 and 1 mA/cm2. Based on the cumulative deposition diagram, it was found that the first three minutes of EPD is the effective deposition time. Applying optimized EPD in composite fabrication of treated GTs caused a drastic improvement on the order of 108 times in the volume conductivity of the nanocomposite laminate in comparison with simple GTs specimens. Optimized CNT deposition also enhanced the ILSS of hierarchical nanocomposites by 42%.

  9. 3D fibre deposition and stereolithography techniques for the design of multifunctional nanocomposite magnetic scaffolds.

    Science.gov (United States)

    De Santis, Roberto; D'Amora, Ugo; Russo, Teresa; Ronca, Alfredo; Gloria, Antonio; Ambrosio, Luigi

    2015-10-01

    Magnetic nanocomposite scaffolds based on poly(ε-caprolactone) and poly(ethylene glycol) were fabricated by 3D fibre deposition modelling (FDM) and stereolithography techniques. In addition, hybrid coaxial and bilayer magnetic scaffolds were produced by combining such techniques. The aim of the current research was to analyse some structural and functional features of 3D magnetic scaffolds obtained by the 3D fibre deposition technique and by stereolithography as well as features of multimaterial scaffolds in the form of coaxial and bilayer structures obtained by the proper integration of such methods. The compressive mechanical behaviour of these scaffolds was investigated in a wet environment at 37 °C, and the morphological features were analysed through scanning electron microscopy (SEM) and X-ray micro-computed tomography. The capability of a magnetic scaffold to absorb magnetic nanoparticles (MNPs) in water solution was also assessed. confocal laser scanning microscopy was used to assess the in vitro biological behaviour of human mesenchymal stem cells (hMSCs) seeded on 3D structures. Results showed that a wide range of mechanical properties, covering those spanning hard and soft tissues, can be obtained by 3D FDM and stereolithography techniques. 3D virtual reconstruction and SEM showed the precision with which the scaffolds were fabricated, and a good-quality interface between poly(ε-caprolactone) and poly(ethylene glycol) based scaffolds was observed for bilayer and coaxial scaffolds. Magnetised scaffolds are capable of absorbing water solution of MNPs, and a preliminary information on cell adhesion and spreading of hMSCs was obtained without the application of an external magnetic field.

  10. A simple method to deposit palladium doped SnO2 thin films using plasma enhanced chemical vapor deposition technique

    International Nuclear Information System (INIS)

    Kim, Young Soon; Wahab, Rizwan; Shin, Hyung-Shik; Ansari, S. G.; Ansari, Z. A.

    2010-01-01

    This work presents a simple method to deposit palladium doped tin oxide (SnO 2 ) thin films using modified plasma enhanced chemical vapor deposition as a function of deposition temperature at a radio frequency plasma power of 150 W. Stannic chloride (SnCl 4 ) was used as precursor and oxygen (O 2 , 100 SCCM) (SCCM denotes cubic centimeter per minute at STP) as reactant gas. Palladium hexafluroacetyleacetonate (Pd(C 5 HF 6 O 2 ) 2 ) was used as a precursor for palladium. Fine granular morphology was observed with tetragonal rutile structure. A peak related to Pd 2 Sn is observed, whose intensity increases slightly with deposition temperature. Electrical resistivity value decreased from 8.6 to 0.9 mΩ cm as a function of deposition temperature from 400 to 600 deg. C. Photoelectron peaks related to Sn 3d, Sn 3p3, Sn 4d, O 1s, and C 1s were detected with varying intensities as a function of deposition temperature.

  11. Investigation on vanadium oxide thin films deposited by spray pyrolysis technique

    Energy Technology Data Exchange (ETDEWEB)

    Margoni, Mudaliar Mahesh; Mathuri, S.; Ramamurthi, K., E-mail: krmurthin@yahoo.co.in, E-mail: ramamurthi.k@ktr.srmuniv.ac.in [Crystal Growth and Thin Film Laboratory, Department of Physics and Nanotechnology, Faculty of Engineering and Technology, SRM University, Kattankulathur – 603 203, Kancheepuram Dt., Tamil Nadu (India); Babu, R. Ramesh [Crystal Growth and Thin Film Laboratory, School of Physics, Bharathidasan University, Tiruchirappalli – 620024, Tamil Nadu (India); Sethuraman, K. [School of Physics, Madurai Kamaraj University, Madurai – 625 021, Tamil Nadu (India)

    2016-05-06

    Vanadium oxide thin films were deposited at 400 °C by spray pyrolysis technique using 0.1 M aqueous precursor solution of ammonium meta vanadate (AMV) with two different pH values. X-ray diffraction results showed that the film prepared using aqueous precursor AMV solution (solution A; pH 7) is amorphous in nature and the film prepared by adding HNO{sub 3} in the AMV aqua solution A (solution B; pH 3) is polycrystalline in nature. Vanadium oxide film prepared from the precursor solution B is in the mixed phases of V{sub 2}O{sub 5} and V{sub 4}O{sub 7}. Crystallinity is improved for the film prepared using solution B when compared to film prepared from solution A. Crystallite size, strain and dislocation density calculated for the film prepared from solution B is respectively 72.1 nm, 0.4554 × 10{sup −3} lin.{sup −2}m{sup −4} and 1.7263 × 10{sup 14} lin.m{sup −2}. Morphology study revealed that the size of the flakes formed on the surface of the films is influenced by the pH of the precursor solution. Average Visible Transmittance and maximum transmittance of the deposited films exceed 70% and the direct optical band gap value calculated for the films deposited from A and B solution is 1.91 eV and 2.08 eV respectively.

  12. Preparation and characterization of VOx nanorods using pulsed laser deposition technique

    International Nuclear Information System (INIS)

    Rama, N.; Senthil Kumar, E.; Ramachandra Rao, M.S.

    2009-01-01

    Full text: Vanadium oxide (VO x ) is one of the most functional oxides of the transition metal oxide family. This versatility comes because of the ability of Vanadium to exist as both monovalent and multivalent in these oxides. These oxides find potential usage in the field of thermochromism electrochromism catalysts, electrochemistry etc. especially in their nano-form because of their increased sensitivity to these applications. These nano-forms are usually prepared using conventional techniques such as solgel techniques, vapour phase transport, hydrothermal synthesis etc. In this work we have used pulsed laser deposition technique to fabricate vanadium oxide nanorods for the first time. The grown nanorods has a predominant VO 2 phase with a secondary phase of V 3 O 7 . The diameters of the rods were around 300 nm with Raman spectra showing all the group vibrations corresponding to VO x phase. The nanorods exhibited photoluminescence in the visible range due to the presence of oxygen defects. These results, including the mechanism of growth of these nanorods, will be discussed in detail. The existence of multivalence in these rods finds potential applications in electrochemistry while the visible photoluminescence in optical applications

  13. Tuning the morphology of metastable MnS films by simple chemical bath deposition technique

    Science.gov (United States)

    Dhandayuthapani, T.; Girish, M.; Sivakumar, R.; Sanjeeviraja, C.; Gopalakrishnan, R.

    2015-10-01

    In the present investigation, we have prepared the spherical particles, almond-like, and cauliflower-like morphological structures of metastable MnS films on glass substrate by chemical bath deposition technique at low temperature without using any complexing or chelating agent. The morphological change of MnS films with molar ratio may be due to the oriented aggregation of adjacent particles. The compositional purity of deposited film was confirmed by the EDAX study. X-ray diffraction and micro-Raman studies confirm the sulfur source concentration induced enhancement in the crystallization of films with metastable MnS phase (zinc-blende β-MnS, and wurtzite γ-MnS). The shift in PL emission peak with molar ratio may be due to the change in optical energy band gap of the MnS, which was further confirmed by the optical absorbance study. The paramagnetic behavior of the sample was confirmed by the M-H plot.

  14. Tuning the morphology of metastable MnS films by simple chemical bath deposition technique

    Energy Technology Data Exchange (ETDEWEB)

    Dhandayuthapani, T. [Directorate of Distance Education, Alagappa University, Karaikudi 630004 (India); Girish, M. [Department of Physics, Alagappa University, Karaikudi 630004 (India); Sivakumar, R., E-mail: krsivakumar1979@yahoo.com [Directorate of Distance Education, Alagappa University, Karaikudi 630004 (India); Sanjeeviraja, C. [Department of Physics, Alagappa Chettiar College of Engineering and Technology, Karaikudi 630004 (India); Gopalakrishnan, R. [Department of Physics, Anna University, Chennai 600025 (India)

    2015-10-30

    Graphical abstract: - Highlights: • MnS films with diverse morphological features were prepared without any complexing agent. • The change in morphology of MnS films may be due to the “oriented aggregation”. • The dual role (as sulfur source and structure directing agent) of thiourea was observed. • Sulfur source concentration induced enhancement in the crystallization of films. - Abstract: In the present investigation, we have prepared the spherical particles, almond-like, and cauliflower-like morphological structures of metastable MnS films on glass substrate by chemical bath deposition technique at low temperature without using any complexing or chelating agent. The morphological change of MnS films with molar ratio may be due to the oriented aggregation of adjacent particles. The compositional purity of deposited film was confirmed by the EDAX study. X-ray diffraction and micro-Raman studies confirm the sulfur source concentration induced enhancement in the crystallization of films with metastable MnS phase (zinc-blende β-MnS, and wurtzite γ-MnS). The shift in PL emission peak with molar ratio may be due to the change in optical energy band gap of the MnS, which was further confirmed by the optical absorbance study. The paramagnetic behavior of the sample was confirmed by the M–H plot.

  15. Recent advances in controlled synthesis of two-dimensional transition metal dichalcogenides via vapour deposition techniques

    KAUST Repository

    Shi, Yumeng

    2014-10-20

    In recent years there have been many breakthroughs in two-dimensional (2D) nanomaterials, among which the transition metal dichalcogenides (TMDs) attract significant attention owing to their unusual properties associated with their strictly defined dimensionalities. TMD materials with a generalized formula of MX2, where M is a transition metal and X is a chalcogen, represent a diverse and largely untapped source of 2D systems. Semiconducting TMD monolayers such as MoS2, MoSe2, WSe2 and WS2 have been demonstrated to be feasible for future electronics and optoelectronics. The exotic electronic properties and high specific surface areas of 2D TMDs offer unlimited potential in various fields including sensing, catalysis, and energy storage applications. Very recently, the chemical vapour deposition technique (CVD) has shown great promise to generate high-quality TMD layers with a scalable size, controllable thickness and excellent electronic properties. Wafer-scale deposition of mono to few layer TMD films has been obtained. Despite the initial success in the CVD synthesis of TMDs, substantial research studies on extending the methodology open up a new way for substitution doping, formation of monolayer alloys and producing TMD stacking structures or superlattices. In this tutorial review, we will introduce the latest development of the synthesis of monolayer TMDs by CVD approaches.

  16. Tight comparison of Mg and Y thin film photocathodes obtained by the pulsed laser deposition technique

    Energy Technology Data Exchange (ETDEWEB)

    Lorusso, A. [Dipartimento di Matematica e Fisica “E. De Giorgi”, Università del Salento and Istituto Nazionale di Fisica Nucleare, 73100 Lecce (Italy); Gontad, F., E-mail: francisco.gontad@le.infn.it [Dipartimento di Matematica e Fisica “E. De Giorgi”, Università del Salento and Istituto Nazionale di Fisica Nucleare, 73100 Lecce (Italy); Solombrino, L. [Dipartimento di Matematica e Fisica “E. De Giorgi”, Università del Salento and Istituto Nazionale di Fisica Nucleare, 73100 Lecce (Italy); Chiadroni, E. [Laboratori Nazionali di Frascati, Istituto Nazionale di Fisica Nucleare, 00044 Frascati (Italy); Broitman, E. [Department of Physics, Chemistry and Biology (IFM), Linköping University, SE-58183 Linköping (Sweden); Perrone, A. [Dipartimento di Matematica e Fisica “E. De Giorgi”, Università del Salento and Istituto Nazionale di Fisica Nucleare, 73100 Lecce (Italy)

    2016-11-11

    In this work Magnesium (Mg) and Yttrium (Y) thin films have been deposited on Copper (Cu) polycrystalline substrates by the pulsed laser ablation technique for photocathode application. Such metallic materials are studied for their interesting photoemission properties and are proposed as a good alternative to the Cu photocathode, which is generally used in radio-frequency guns. Mg and Y films were uniform with no substantial differences in morphology; a polycrystalline structure was found for both of them. Photoemission measurements of such cathodes based on thin films were performed, revealing a quantum efficiency higher than Cu bulk. Photoemission theory according to the three-step model of Spicer is invoked to explain the superior photoemission performance of Mg with respect to Y. - Highlights: • Mg and Y thin film photocathodes were successfully prepared by pulsed laser deposition. • Mg quantum efficiency is higher than Y, despite its higher work function. • The three-step model of Spicer justify the difference in quantum efficiency.

  17. CuFeO2 formation using fused deposition modeling 3D printing and sintering technique

    Science.gov (United States)

    Salea, A.; Dasaesamoh, A.; Prathumwan, R.; Kongkaew, T.; Subannajui, K.

    2017-09-01

    CuFeO2 is a metal oxide mineral material which is called delafossite. It can potentially be used as a chemical catalyst, and gas sensing material. There are methods to fabricate CuFeO2 such as chemical synthesis, sintering, sputtering, and chemical vapor deposition. In our work, CuFeO2 is prepared by Fused Deposition Modeling (FDM) 3D printing. The composite filament which composed of Cu and Fe elements is printed in three dimensions, and then sintered and annealed at high temperature to obtain CuFeO2. Suitable polymer blend and maximum percent volume of metal powder are studied. When percent volume of metal powder is increased, melt flow rate of polymer blend is also increased. The most suitable printing condition is reported and the properties of CuFeO2 are observed by Scanning Electron Microscopy, and Dynamic Scanning Calorimeter, X-ray diffraction. As a new method to produce semiconductor, this technique has a potential to allow any scientist or students to design and print a catalyst or sensing material by the most conventional 3D printing machine which is commonly used around the world.

  18. Polyethylene-Carbon Nanotube Composite Film Deposited by Cold Spray Technique

    Science.gov (United States)

    Ata, Nobuhisa; Ohtake, Naoto; Akasaka, Hiroki

    2017-10-01

    Carbon nanotubes (CNTs) are high-performance materials because of their superior electrical conductivity, thermal conductivity, and self-lubrication, and they have been studied for application to polymer composite materials as fillers. However, the methods of fabricating polymer composites with CNTs, such as injection molding, are too complicated for industrial applications. We propose a simple cold spray (CS) technique to obtain a polymer composite of polyethylene (PE) and CNTs. The composite films were deposited by CS on polypropylene and nano-porous structured aluminum substrates. The maximum thickness of the composite film was approximately 1 mm. Peaks at G and D bands were observed in the Raman spectra of the films. Scanning electron microscopy images of the film surface revealed that PE particles were melted by the acceleration gas and CNTs were attached with melted PE. The PE particles solidified after contact with the substrate. These results indicate that PE-CNT composite films were successfully deposited on polypropylene and nano-porous structured aluminum substrates by CS.

  19. Zn Thin Film Deposition for Fe Layer Shielding Use the Sputtering Technique on Cylindrical Form

    International Nuclear Information System (INIS)

    Yunanto; Tjipto Sujitno, BA; Suprapto; Simbolon, Sahat

    2002-01-01

    Deposition of thin film on Fe substrate use sputtering technique on cylindrical form was carried out. The purpose of this research is to protect Fe due to the corrosion with Zn thin film. Sputtering method was proposed to protect a component of complex form. Substrate has functioned as anode, meanwhile target in cylindrical form as a cathode. Argon ion from anode bombard Zn with enough energy for releasing Zn. Zn atom would scatter and some of then was focused on the anode. For testing Zn atom on Fe by using XRF and corrosion rate with potentiostat. It was found that corrosion rate was decreased from 0.051 mpy to 0.031 mpy on 0.63 % of Fe substrate. (author)

  20. In-plane anisotropy and stress detection of films deposited by RC technique

    Science.gov (United States)

    Meydan, T.; Kockar, H.

    2001-12-01

    A Novel Rotating Cryostat (RC) vacuum system originally designed to fabricate organic layers has been developed in order to prepare magnetic materials for specific applications such as sensors. The RC sputtering system has a rotating drum (substrate holder) and the possibility of using multi-port deposition sources. The source material sputtered by a dc magnetron, which was positioned one of the ports around the RC, was an iron disk (25 mm diameter, 0.8 mm thick, 99.8% pure). Results show that films have exhibited isotropic and anisotropic magnetisation at various running conditions of the RC using a Magneto-Optic Loop Plotter (MOKE) and a Vibrating Sample Magnetometer (VSM). Estimation of magnetic anisotropy confirms in-plane anisotropy in the films. Moreover, when these films are subjected to a bending stress within the VSM, they show chances in their hysteresis loops. These findings indicate a possible future for this technique to produce sensing devices for stress detection.

  1. The Storing Matter technique applied to PVC: Effect of the primary ion fluence on the sputter-deposition

    Energy Technology Data Exchange (ETDEWEB)

    Becker, N., E-mail: nbecker@lippmann.l [Department of Science and Analysis of Materials (SAM), Centre de Recherche Public, Gabriel Lippmann, 41 Rue du Brill, L-4422 Belvaux (Luxembourg); Mansilla, C.; Wirtz, T.; Migeon, H.-N. [Department of Science and Analysis of Materials (SAM), Centre de Recherche Public, Gabriel Lippmann, 41 Rue du Brill, L-4422 Belvaux (Luxembourg)

    2011-05-01

    The Storing Matter technique is derived from SIMS (Secondary Ion Mass Spectrometry) and consists in decoupling the sputtering of the specimen from the subsequent analysis step. PVC samples were sputtered by an Ar{sup +} beam with different fluences, and the emitted particles were deposited on a dedicated Ag collector. In a second step, the matter deposited on the collector was analyzed by static SIMS. For each deposit, several analysis points were chosen across a diameter of the collector in order to show the changes in the mass spectra as the deposit coverage changes. It was shown that the Storing Matter technique is sensitive enough to observe some well-known consequences of increasing the primary ion fluence, namely an increasing contribution of aromatic fragments and a decrease in sputtering yield.

  2. Plasma processing techniques for deposition of carbonic thin protective coatings on structural nuclear materials

    International Nuclear Information System (INIS)

    Andrei, V.; Oncioiu, G.; Coaca, E.; Rusu, O.; Lungu, C.

    2009-01-01

    Full text of publication follows: The production of nano-structured surface films with controlled properties is crucial for the development of materials necessary for the Advanced Systems for Nuclear Energy. Since the surface of materials is the zone through which materials interact with the environment, the surface science and surface engineering techniques plays an essential role in the understanding and control of the processes involved. Complex surface structures were developed on stainless steels used as structural nuclear materials: austenitic stainless steels based on Fe, austenitic steels with high content of Cr, ferrites resistant to corrosion, by various Plasma Processing methods which include: - Plasma Electrolytic (PE) treatments: the steel substrates were modified by nitriding and nitro-carburizing plasma diffusion treatments; - carbonic films deposition in Thermionic Vacuum Arc Plasma. The results of the characterization of surface structures obtained in various experimental conditions for improvement of the properties (corrosion resistance, hardness, wear properties) are reported: the processes and structures were characterized by correlation of the results of the complementary techniques: XPS, 'depth profiling', SEM, XRD, EIS. An overall description of the processes involved in the surface properties improvement, and some consideration about the new materials development for energy technologies are presented

  3. Heavy Metals and Trace Elements Atmospheric Deposition Studies in Tula Region Using Moss Biomonitors Technique

    CERN Document Server

    Ermakova, E V; Steinnes, E

    2002-01-01

    For the first time the moss biomonitors technique was used in air pollution studies in Tula Region (Central Russia), applying NAA, AAS. Moss samples were collected at 83 sites in accordance with the sampling strategy adopted in European projects on biomonitoring atmospheric deposition. A wide set of trace elements in mosses was determined. The method of epithermal neutron activation at IBR-2 reactor of FLNP JINR has made it possible to identify 33 elements (Na, Mg, Al, Cl, K, Ca, Sc, V, Cr, Mn, Fe, Co, Ni, Zn, As, Br, Rb, Sr, Mo, Sb, I, Cs, Ba, La, Ce, Sm, Tb, Yb, Hf, Ta, W, Th, U) in the large-scale concentration range - from 10000 ppm for K to 0,001 ppm for Tb and Ta. Cu, Cd and Pb were determined by the flame AAS in the Norwegian Institute of Science and Technology. Using the graphical technique and principal component analysis allowed to separate plant, crustal and general pollution components in the moss. The obtained data will be used for constructing coloured maps of the distribution of elements over t...

  4. Optimal properties for coated titanium implants with the hydroxyapatite layer formed by the pulsed laser deposition technique

    Science.gov (United States)

    Himmlova, Lucia; Dostalova, Tatjana; Jelinek, Miroslav; Bartova, Jirina; Pesakova, V.; Adam, M.

    1999-02-01

    Pulsed laser deposition technique allow to 'tailor' bioceramic coat for metal implants by the change of deposition conditions. Each attribute is influenced by the several deposition parameters and each parameter change several various properties. Problem caused that many parameters has an opposite function and improvement of one property is followed by deterioration of other attribute. This study monitor influence of each single deposition parameter and evaluate its importance form the point of view of coat properties. For deposition KrF excimer laser in stainless-steel deposition chamber was used. Deposition conditions (ambient composition and pressures, metallic substrate temperature, energy density and target-substrate distance) were changed according to the film properties. A non-coated titanium implant was used as a control. Films with promising mechanical quality underwent an in vitro biological tests -- measurement of proliferation activity, observing cell interactions with macrophages, fibroblasts, testing toxicity of percolates, observing a solubility of hydroxyapatite (HA) coat. Deposition conditions corresponding with the optimal mechanical and biochemical properties are: metal temperature 490 degrees Celsius, ambient-mixture of argon and water vapor, energy density 3 Jcm-2, target-substrate distance 7.5 cm.

  5. Laboratory model study of newly deposited dredger fills using improved multiple-vacuum preloading technique

    Directory of Open Access Journals (Sweden)

    Jingjin Liu

    2017-10-01

    Full Text Available Problems continue to be encountered concerning the traditional vacuum preloading method in field during the treatment of newly deposited dredger fills. In this paper, an improved multiple-vacuum preloading method was developed to consolidate newly dredger fills that are hydraulically placed in seawater for land reclamation in Lingang Industrial Zone of Tianjin City, China. With this multiple-vacuum preloading method, the newly deposited dredger fills could be treated effectively by adopting a novel moisture separator and a rapid improvement technique without sand cushion. A series of model tests was conducted in the laboratory for comparing the results from the multiple-vacuum preloading method and the traditional one. Ten piezometers and settlement plates were installed to measure the variations in excess pore water pressures and moisture content, and vane shear strength was measured at different positions. The testing results indicate that water discharge–time curves obtained by the traditional vacuum preloading method can be divided into three phases: rapid growth phase, slow growth phase, and steady phase. According to the process of fluid flow concentrated along tiny ripples and building of larger channels inside soils during the whole vacuum loading process, the fluctuations of pore water pressure during each loading step are divided into three phases: steady phase, rapid dissipation phase, and slow dissipation phase. An optimal loading pattern which could have a best treatment effect was proposed for calculating the water discharge and pore water pressure of soil using the improved multiple-vacuum preloading method. For the newly deposited dredger fills at Lingang Industrial Zone of Tianjin City, the best loading step was 20 kPa and the loading of 40–50 kPa produced the highest drainage consolidation. The measured moisture content and vane shear strength were discussed in terms of the effect of reinforcement, both of which indicate

  6. Low-temperature deposition of ZnO thin films on PET and glass substrates by DC-sputtering technique

    International Nuclear Information System (INIS)

    Banerjee, A.N.; Ghosh, C.K.; Chattopadhyay, K.K.; Minoura, Hideki; Sarkar, Ajay K.; Akiba, Atsuya; Kamiya, Atsushi; Endo, Tamio

    2006-01-01

    The structural, optical and electrical properties of ZnO thin films (260 - 490 nm thick) deposited by direct-current sputtering technique, at a relatively low-substrate temperature (363 K), onto polyethylene terephthalate and glass substrates have been investigated. X-ray diffraction patterns confirm the proper phase formation of the material. Optical transmittance data show high transparency (80% to more than 98%) of the films in the visible portion of solar radiation. Slight variation in the transparency of the films is observed with a variation in the deposition time. Electrical characterizations show the room-temperature conductivity of the films deposited onto polyethylene terephthalate substrates for 4 and 5 h around 0.05 and 0.25 S cm -1 , respectively. On the other hand, for the films deposited on glass substrates, these values are 8.5 and 9.6 S cm -1 for similar variation in the deposition time. Room-temperature conductivity of the ZnO films deposited on glass substrates is at least two orders of magnitude higher than that of ZnO films deposited onto polyethylene terephthalate substrates under identical conditions. Hall-measurements show the maximum carrier concentration of the films on PET and glass substrate around 2.8 x 10 16 and 3.1 x 10 2 cm -3 , respectively. This report will provide newer applications of ZnO thin films in flexible display technology

  7. Self-limiting growth of anatase TiO{sub 2}: A comparison of two deposition techniques

    Energy Technology Data Exchange (ETDEWEB)

    Kubala, Nicholas G. [Department of Chemical Engineering, Colorado School of Mines, Golden, CO 80401 (United States); Wolden, Colin A., E-mail: cwolden@mines.ed [Department of Chemical Engineering, Colorado School of Mines, Golden, CO 80401 (United States)

    2010-09-30

    Self-limiting deposition of titanium dioxide thin films was accomplished using pulsed plasma-enhanced chemical vapor deposition (PECVD) and plasma-enhanced atomic layer deposition (PEALD) at low temperatures (T < 200 {sup o}C) using TiCl{sub 4} and O{sub 2}. TiCl{sub 4} is shown to be inert with molecular oxygen at process conditions, making it a suitable precursor for these processes. The deposition kinetics were examined as a function of TiCl{sub 4} exposure and substrate temperature. The quality of the anatase films produced by the two techniques was nominally identical. The key distinctions are found in precursor utilization and conformality. Pulsed PECVD requires 20 times less TiCl{sub 4}, while PEALD must be used to uniformly coat complex topographies.

  8. Optical and Surface Characteristics of Mg-Doped GaAs Nanocrystalline Thin Film Deposited by Thermionic Vacuum Arc Technique

    Science.gov (United States)

    Pat, Suat; Özen, Soner; Şenay, Volkan; Korkmaz, Şadan

    2017-01-01

    Magnesium (Mg) is the most promising p-type dopant for gallium arsenide (GaAs) semiconductor technology. Mg-doped GaAs nanocrystalline thin film has been deposited at room temperature by the thermionic vacuum arc technique, a rapid deposition method for production of doped GaAs material. The microstructure and surface and optical properties of the deposited sample were investigated by x-ray diffraction analysis, scanning electron microscopy, energy-dispersive x-ray spectroscopy, atomic force microscopy, ultraviolet-visible spectrophotometry, and interferometry. The crystalline direction of the deposited sample was determined to be (220) plane and (331) plane at 44.53° and 72.30°, respectively. The Mg-doped GaAs nanocrystalline sample showed high transmittance.

  9. Characterizations of multilayer ZnO thin films deposited by sol-gel spin coating technique

    Directory of Open Access Journals (Sweden)

    M.I. Khan

    Full Text Available In this work, zinc oxide (ZnO multilayer thin films are deposited on glass substrate using sol-gel spin coating technique and the effect of these multilayer films on optical, electrical and structural properties are investigated. It is observed that these multilayer films have great impact on the properties of ZnO. X-ray Diffraction (XRD confirms that ZnO has hexagonal wurtzite structure. Scanning Electron Microscopy (SEM showed the crack-free films which have uniformly distributed grains structures. Both micro and nano particles of ZnO are present on thin films. Four point probe measured the electrical properties showed the decreasing trend between the average resistivity and the number of layers. The optical absorption spectra measured using UV–Vis. showed the average transmittance in the visible region of all films is 80% which is good for solar spectra. The performance of the multilayer as transparent conducting material is better than the single layer of ZnO. This work provides a low cost, environment friendly and well abandoned material for solar cells applications. Keywords: Multilayer films, Semiconductor, ZnO, XRD, SEM, Optoelectronic properties

  10. Filament Breakage Monitoring in Fused Deposition Modeling Using Acoustic Emission Technique

    Directory of Open Access Journals (Sweden)

    Zhensheng Yang

    2018-03-01

    Full Text Available Polymers are being used in a wide range of Additive Manufacturing (AM applications and have been shown to have tremendous potential for producing complex, individually customized parts. In order to improve part quality, it is essential to identify and monitor the process malfunctions of polymer-based AM. The present work endeavored to develop an alternative method for filament breakage identification in the Fused Deposition Modeling (FDM AM process. The Acoustic Emission (AE technique was applied due to the fact that it had the capability of detecting bursting and weak signals, especially from complex background noises. The mechanism of filament breakage was depicted thoroughly. The relationship between the process parameters and critical feed rate was obtained. In addition, the framework of filament breakage detection based on the instantaneous skewness and relative similarity of the AE raw waveform was illustrated. Afterwards, we conducted several filament breakage tests to validate their feasibility and effectiveness. Results revealed that the breakage could be successfully identified. Achievements of the present work could be further used to develop a comprehensive in situ FDM monitoring system with moderate cost.

  11. Al2O3 Coatings on Magnesium Alloy Deposited by the Fluidized Bed (FB Technique

    Directory of Open Access Journals (Sweden)

    Gabriele Baiocco

    2018-01-01

    Full Text Available Magnesium alloys are widely employed in several industrial domains for their outstanding properties. They have a high strength-weight ratio, with a density that is lower than aluminum (33% less, and feature good thermal properties, dimensional stability, and damping characteristics. However, they are vulnerable to oxidation and erosion-corrosion phenomena when applied in harsh service conditions. To avoid the degradation of magnesium, several coating methods have been presented in the literature; however, all of them deal with drawbacks that limit their application in an industrial environment, such as environmental pollution, toxicity of the coating materials, and high cost of the necessary machinery. In this work, a plating of Al2O3 film on a magnesium alloy realized by the fluidized bed (FB technique and using alumina powder is proposed. The film growth obtained through this cold deposition process is analyzed, investigating the morphology as well as tribological and mechanical features and corrosion behavior of the plated samples. The resulting Al2O3 coatings show consistent improvement of the tribological and anti-corrosive performance of the magnesium alloy.

  12. Deposition of corrosion products from dowels on human dental root surfaces measured with proton microprobe technique

    Science.gov (United States)

    Brune, D.; Brunell, G.; Lindh, U.

    1982-06-01

    Distribution of copper, mercury and zinc on human teeth root surfaces adjacent to dowels of gold alloy or brass as well as dowels of brass in conjunction with an amalgam crown has been measured with a proton microprobe using PIXE techniques. Upper limits of the contents of gold and silver on the root surfaces were established. Pronounced concentration profiles of copper and zinc were observed on the root surfaces of teeth prepared with dowels of brass. The dowel of gold alloy revealed only zinc deposition. The major part of copper on the root surfaces is assumed to arise from corrosion of the dowels, and has been transported to the surface by diffusion through the dential tubuli. Zinc in the volume analysed is a constituent of dentin tissue as well as a corrosion product of the brass dowel. Part of the zinc level could also be ascribed to erosion of the zinc phosphate cement matrix. The volumes analysed were (25×25×25)μm 3. The levels of copper, mercury and zinc on the tooth root surfaces attained values up to about 200, 20 and 600 ppm, respectively.

  13. Al₂O₃ Coatings on Magnesium Alloy Deposited by the Fluidized Bed (FB) Technique.

    Science.gov (United States)

    Baiocco, Gabriele; Rubino, Gianluca; Tagliaferri, Vincenzo; Ucciardello, Nadia

    2018-01-09

    Magnesium alloys are widely employed in several industrial domains for their outstanding properties. They have a high strength-weight ratio, with a density that is lower than aluminum (33% less), and feature good thermal properties, dimensional stability, and damping characteristics. However, they are vulnerable to oxidation and erosion-corrosion phenomena when applied in harsh service conditions. To avoid the degradation of magnesium, several coating methods have been presented in the literature; however, all of them deal with drawbacks that limit their application in an industrial environment, such as environmental pollution, toxicity of the coating materials, and high cost of the necessary machinery. In this work, a plating of Al₂O₃ film on a magnesium alloy realized by the fluidized bed (FB) technique and using alumina powder is proposed. The film growth obtained through this cold deposition process is analyzed, investigating the morphology as well as tribological and mechanical features and corrosion behavior of the plated samples. The resulting Al₂O₃ coatings show consistent improvement of the tribological and anti-corrosive performance of the magnesium alloy.

  14. Improved Understanding of Implosion Symmetry through New Experimental Techniques Connecting Hohlraum Dynamics with Laser Beam Deposition

    Science.gov (United States)

    Ralph, Joseph; Salmonson, Jay; Dewald, Eduard; Bachmann, Benjamin; Edwards, John; Graziani, Frank; Hurricane, Omar; Landen, Otto; Ma, Tammy; Masse, Laurent; MacLaren, Stephen; Meezan, Nathan; Moody, John; Parrilla, Nicholas; Pino, Jesse; Sacks, Ryan; Tipton, Robert

    2017-10-01

    Understanding what affects implosion symmetry has been a challenge for scientists designing indirect drive inertial confinement fusion experiments on the National Ignition Facility (NIF). New experimental techniques and data analysis have been employed aimed at improving our understanding of the relationship between hohlraum dynamics and implosion symmetry. Thin wall imaging data allows for time-resolved imaging of 10 keV Au l-band x-rays providing for the first time on the NIF, a spatially resolved measurement of laser deposition with time. In the work described here, we combine measurements from the thin wall imaging with time resolved views of the interior of the hohlraum. The measurements presented are compared to hydrodynamic simulations as well as simplified physics models. The goal of this work is to form a physical picture that better explains the relationship of the hohlraum dynamics and capsule ablator on laser beam propagation and implosion symmetry. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under contract DE-AC52-07NA27344.

  15. Organo-layered double hydroxides composite thin films deposited by laser techniques

    Science.gov (United States)

    Birjega, R.; Vlad, A.; Matei, A.; Dumitru, M.; Stokker-Cheregi, F.; Dinescu, M.; Zavoianu, R.; Raditoiu, V.; Corobea, M. C.

    2016-06-01

    We used laser techniques to create hydrophobic thin films of layered double hydroxides (LDHs) and organo-modified LDHs. A LDH based on Zn-Al with Zn2+/Al3+ ratio of 2.5 was used as host material, while dodecyl sulfate (DS), which is an organic surfactant, acted as guest material. Pulsed laser deposition (PLD) and matrix assisted pulsed laser evaporation (MAPLE) were employed for the growth of the films. The organic anions were intercalated in co-precipitation step. The powders were subsequently used either as materials for MAPLE, or they were pressed and used as targets for PLD. The surface topography of the thin films was investigated by atomic force microscopy (AFM), the crystallographic structure of the powders and films was checked by X-ray diffraction. FTIR spectroscopy was used to evidence DS interlayer intercalation, both for powders and the derived films. Contact angle measurements were performed in order to establish the wettability properties of the as-prepared thin films, in view of functionalization applications as hydrophobic surfaces, owing to the effect of DS intercalation.

  16. Yb2Si2O7 Environmental Barrier Coatings Deposited by Various Thermal Spray Techniques: A Preliminary Comparative Study

    Science.gov (United States)

    Bakan, Emine; Marcano, Diana; Zhou, Dapeng; Sohn, Yoo Jung; Mauer, Georg; Vaßen, Robert

    2017-08-01

    Dense, crack-free, uniform, and well-adhered environmental barrier coatings (EBCs) are required to enhance the environmental durability of silicon (Si)-based ceramic matrix composites in high pressure, high gas velocity combustion atmospheres. This paper represents an assessment of different thermal spray techniques for the deposition of Yb2Si2O7 EBCs. The Yb2Si2O7 coatings were deposited by means of atmospheric plasma spraying (APS), high-velocity oxygen fuel spraying (HVOF), suspension plasma spraying (SPS), and very low-pressure plasma spraying (VLPPS) techniques. The initial feedstock, as well as the deposited coatings, were characterized and compared in terms of their phase composition. The as-sprayed amorphous content, microstructure, and porosity of the coatings were further analyzed. Based on this preliminary investigation, the HVOF process stood out from the other techniques as it enabled the production of vertical crack-free coatings with higher crystallinity in comparison with the APS and SPS techniques in atmospheric conditions. Nevertheless, VLPPS was found to be the preferred process for the deposition of Yb2Si2O7 coatings with desired characteristics in a controlled-atmosphere chamber.

  17. Studies of CdS/CdTe interface: Comparison of CdS films deposited by close space sublimation and chemical bath deposition techniques

    International Nuclear Information System (INIS)

    Han, Jun-feng; Fu, Gan-hua; Krishnakumar, V.; Schimper, Hermann-Josef; Liao, Cheng; Jaegermann, Wolfram; Besland, M.P.

    2015-01-01

    The CdS layers were deposited by two different methods, close space sublimation (CSS) and chemical bath deposition (CBD) technique. The CdS/CdTe interface properties were investigated by transmission electron microscope (TEM) and X-ray photoelectron spectroscopy (XPS). The TEM images showed a large CSS-CdS grain size in the range of 70-80 nm. The interface between CSS-CdS and CdTe were clear and sharp, indicating an abrupt hetero-junction. On the other hand, CBD-CdS layer had much smaller grain size in the 5-10 nm range. The interface between CBD-CdS and CdTe was not as clear as CSS-CdS. With the stepwise coverage of CdTe layer, the XPS core levels of Cd 3d and S 2p in CSS-CdS had a sudden shift to lower binding energies, while those core levels shifted gradually in CBD-CdS. In addition, XPS depth profile analyses indicated a strong diffusion in the interface between CBD-CdS and CdTe. The solar cells prepared using CSS-CdS yielded better device performance than the CBD-CdS layer. The relationships between the solar cell performances and properties of CdS/CdTe interfaces were discussed. - Highlights: • Studies of CdS deposited by close space sublimation and chemical bath deposition • An observation of CdS/CdTe interface by transmission electron microscope • A careful investigation of CdS/CdTe interface by X ray photoelectron spectra • An easier diffusion at the chemical bath deposition CdS and CdTe interface

  18. An economic CVD technique for pure SnO2 thin films deposition ...

    Indian Academy of Sciences (India)

    sis of the hydrolysis reaction between tin tetrachloride and water vapour showed that the rate of deposition of SnO2 is a strong function of the temperature and the ratio of the reactants. Later, in the year 1990, undoped tin oxide films have been prepared by a chemical vapour deposition tech- nique by Sanon et al (1990).

  19. CdS thin films obtained by thermal treatment of cadmium(II) complex precursor deposited by MAPLE technique

    International Nuclear Information System (INIS)

    Rotaru, Andrei; Mietlarek-Kropidlowska, Anna; Constantinescu, Catalin; Scarisoreanu, Nicu; Dumitru, Marius; Strankowski, Michal; Rotaru, Petre; Ion, Valentin; Vasiliu, Cristina; Becker, Barbara; Dinescu, Maria

    2009-01-01

    Thin films of [Cd{SSi(O-Bu t ) 3 }(S 2 CNEt 2 )] 2 , precursor for semiconducting CdS layers, were deposited on silicon substrates by Matrix-Assisted Pulsed Laser Evaporation (MAPLE) technique. Structural analysis of the obtained films by Fourier transform infrared spectroscopy (FTIR) confirmed the viability of the procedure. After the deposition of the coordination complex, the layers are manufactured by appropriate thermal treatment of the system (thin film and substrate), according to the thermal analysis of the compound. Surface morphology of the thin films was investigated by atomic force microscopy (AFM) and spectroscopic-ellipsometry (SE) measurements.

  20. Demonstration of feasibility of depositing semiconductor layers using microwave enhanced plasma techniques. Final technical report

    Energy Technology Data Exchange (ETDEWEB)

    1985-01-01

    Manufacturing of low cost more efficient photovoltaic cells partly depends on the development of new process technologies, one of which is the deposition of thin films at relatively low substrate temperatures. Superwave Technology, in an effort to demonstrate the feasibility of microwave enhanced plasma as a means of producing better quality films, has successfully developed a simple but versatile system. The microwave enhanced plasma system developed has the capability of depositing various films of different compositions. This effort was directed towards deposition of silicon nitride film through gas phase plasma reaction.

  1. Influence of solution deposition rate on properties of V{sub 2}O{sub 5} thin films deposited by spray pyrolysis technique

    Energy Technology Data Exchange (ETDEWEB)

    Abd–Alghafour, N. M., E-mail: na2013bil@gmail.com [Iraqi Ministry of Education, Anbar (Iraq); Ahmed, Naser M.; Hassan, Zai; Mohammad, Sabah M. [Nano-Optoelectronics Research and Technology Laboratory, School of Physics, University Sains Malaysia,11800 Penang (Malaysia)

    2016-07-19

    Vanadium oxide (V{sub 2}O{sub 5}) thin films were deposited on glass substrates by using a cost-efficient spray pyrolysis technique. The films were grown at 350° through thermal decomposition of VCl{sub 3} in deionized water with different solution spray rates. The high resolution X-ray diffraction results revealed the formation of nanocrystalline films having orthorhombic structures with preferential orientation along (101) direction. The spray rate influenced the surface morphology and crystallite size of the films. The crystallite size was found to increase whereas the micro-strain was decreased by increasing the spray deposition rates. The increase in crystallite size and decrease in the macrostrain resulted in an improvement in the films’ crystallinity. The UV-Visible spectroscopy analysis indicated that the average transmittance of all films lies in the range 75-80 %. The band gap of V{sub 2}O{sub 5} film was decreased from 2.65 to 2.46 eV with increase of the spray deposition rate from 5 ml/min to 10 ml/min. first, second, and third level headings (first level heading).

  2. A Mini-Prototype YBCO SMES Using Combustion Chemical Vapor Deposition Technique

    National Research Council Canada - National Science Library

    Shoup, Shara

    2000-01-01

    .... Textured nickel metal substrates were joined by 1 mm joints by several methods and in several physical configurations and then tested for feasibility by using the Combustion Chemical Vapor Deposition (CCVD...

  3. Evaluation of Co-rich manganese deposits by image analysis and photogrammetric techniques

    Digital Repository Service at National Institute of Oceanography (India)

    Yamazaki, T.; Sharma, R.; Tsurusaki, K.

    Stereo-seabed photographs of Co-rich manganese deposits on a mid-Pacific seamount, were analysed using an image analysis software for coverage estimation and size classification of nodules, and a photogrammetric software for calculation of height...

  4. Identification of sources of tar balls deposited along the Goa coast, India, using fingerprinting techniques

    Digital Repository Service at National Institute of Oceanography (India)

    Suneel, V.; Vethamony, P.; Zakaria, M.P.; Naik, B.G.; Prasad, K.V.

    Deposition of tar balls along the coast of Goa, India is a common phenomenon during the southwest monsoon. Representative tar ball samples collected from various beaches of Goa and one Bombay High (BH) crude oil sample were subjected to fingerprint...

  5. Atmospheric deposition of trace elements around Ulan Bator city studied by moss and lichen biomonitoring technique and INAA

    International Nuclear Information System (INIS)

    Ganbold, G.; Gehrbish, Sh.; Tsehndehehkhuu, Ts.; Gundorina, S.F.; Frontas'eva, M.V.; Ostrovnaya, T.M.; Pavlov, S.S.

    2005-01-01

    For the first time the moss and lichen biomonitoring technique has been applied to air pollution in Mongolia (Ulan-Bator, the capital city). INAA at the IBR-2 reactor has made it possible to determine the content of 35 elements in moss and lichen biomonitors. Samples collected at sites located 10-15 km from the center of Ulan-Bator were analyzed by Instrumental Neutron Activation Analysis (INAA) using epithermal neutrons. The mosses (Rhytidium rugosum, Thuidium abietinum, Entodon concinnus) and lichens (Cladonia stellaris, Parmelia separata) were used to study the atmospheric deposition of trace elements. It was shown that the suggested types of mosses could be used as suitable biomonitors to estimate the concentration levels of heavy metals and trace elements in Ulan-Bator atmospheric deposition. The results are compared to the data of atmospheric deposition of some European countries

  6. Atmospheric Deposition of Trace Elements Around Ulan-Bator City Studied by Moss and Lichen Biomonitoring Technique and INAA

    CERN Document Server

    Ganbold, G; Gundorina, S F; Frontasyeva, M V; Ostrovnaya, T M; Pavlov, S S; Tsendeekhuu, T

    2005-01-01

    For the first time the moss and lichen biomonitoring technique has been applied to air pollution in Mongolia (Ulan-Bator, the capital city). INAA at the IBR-2 reactor has made it possible to determine the content of 35 elements in moss and lichen biomonitors. Samples collected at sites located 10-15 km from the center of Ulan-Bator were analyzed by Instrumental Neutron Activation Analysis (INAA) using epithermal neutrons. The mosses (\\textit{Rhytidium rugosum}, \\textit{Thuidium abietinum}, \\textit{Entodon concinnus}) and lichens (\\textit{Cladonia stellaris}, \\textit{Parmelia separata}) were used to study the atmospheric deposition of trace elements. It was shown that the suggested types of mosses could be used as suitable biomonitors to estimate the concentration levels of heavy metals and trace elements in Ulan-Bator atmospheric deposition. The results are compared to the data of atmospheric deposition of some European countries.

  7. Thickness dependence of optical parameters for ZnTe thin films deposited by electron beam gun evaporation technique

    International Nuclear Information System (INIS)

    Salem, A.M.; Dahy, T.M.; El-Gendy, Y.A.

    2008-01-01

    Zinc telluride thin films with different thicknesses have been deposited by electron beam gun evaporation system onto glass substrates at room temperature. X-ray and electron diffraction techniques have been employed to determine the crystal structure and the particle size of the deposited films. The stoichiometry of the deposited films was confirmed by means of energy-dispersive X-ray spectrometry. The optical transmission and reflection spectrum of the deposited films have been recorded in the wavelength optical range 450-2500 nm. The variation of the optical parameters, i.e. refractive index, n, extinction coefficient, k, with thickness of the deposited films has been investigated. The refractive index dispersion in the transmission and low absorption region is adequately described by the single-oscillator model, whereby the values of the oscillator strength, oscillator position, dispersion parameter as well as the high-frequency dielectric constant were calculated for different film thickness. Graphical representations of the surface and volume energy loss function were also presented

  8. Atmospheric-pressure epitaxial growth technique of a multiple quantum well by mist chemical vapor deposition based on Leidenfrost droplets

    Science.gov (United States)

    Kawaharamura, Toshiyuki; Dang, Giang T.; Nitta, Noriko

    2016-10-01

    A multiple quantum well α-Fe2O3/α-Ga2O3 with parallel and coherent formation of uniform and highly single-crystalline layers on a sapphire substrate has been fabricated by open-air atmospheric-pressure solution-processed mist chemical vapor deposition (Mist CVD). This report demonstrates that complicated structures with atomic-level control can be fabricated even in non-vacuum conditions by the Mist CVD. This can be achieved via the precise control of the precursor flow and ambient temperature combined with the formation of mist droplets of the special Leidenfrost state, which increased the atomic migration length by 108 times more than that of traditional vacuum techniques. This work could be a milestone in the transformation from vacuum to non-vacuum thin film deposition techniques towards a green and sustainable industry.

  9. Assessment of multiple geophysical techniques for the characterization of municipal waste deposit sites

    Science.gov (United States)

    Gaël, Dumont; Tanguy, Robert; Nicolas, Marck; Frédéric, Nguyen

    2017-10-01

    In this study, we tested the ability of geophysical methods to characterize a large technical landfill installed in a former sand quarry. The geophysical surveys specifically aimed at delimitating the deposit site horizontal extension, at estimating its thickness and at characterizing the waste material composition (the moisture content in the present case). The site delimitation was conducted with electromagnetic (in-phase and out-of-phase) and magnetic (vertical gradient and total field) methods that clearly showed the transition between the waste deposit and the host formation. Regarding waste deposit thickness evaluation, electrical resistivity tomography appeared inefficient on this particularly thick deposit site. Thus, we propose a combination of horizontal to vertical noise spectral ratio (HVNSR) and multichannel analysis of the surface waves (MASW), which successfully determined the approximate waste deposit thickness in our test landfill. However, ERT appeared to be an appropriate tool to characterize the moisture content of the waste, which is of prior information for the organic waste biodegradation process. The global multi-scale and multi-method geophysical survey offers precious information for site rehabilitation studies, water content mitigation processes for enhanced biodegradation or landfill mining operation planning.

  10. Novel GIMS technique for deposition of colored Ti/TiO₂ coatings on industrial scale

    Directory of Open Access Journals (Sweden)

    Zdunek Krzysztof

    2016-03-01

    Full Text Available The aim of the present paper has been to verify the effectiveness and usefulness of a novel deposition process named GIMS (Gas Injection Magnetron Sputtering used for the flrst time for deposition of Ti/TiO₂ coatings on large area glass Substrates covered in the condition of industrial scale production. The Ti/TiO₂ coatings were deposited in an industrial System utilizing a set of linear magnetrons with the length of 2400 mm each for covering the 2000 × 3000 mm glasses. Taking into account the speciflc course of the GIMS (multipoint gas injection along the magnetron length and the scale of the industrial facility, the optical coating uniformity was the most important goal to check. The experiments on Ti/TiO₂ coatings deposited by the use of GIMS were conducted on Substrates in the form of glass plates located at the key points along the magnetrons and intentionally non-heated during any stage of the process. Measurements of the coatings properties showed that the thickness and optical uniformity of the 150 nm thick coatings deposited by GIMS in the industrial facility (the thickness differences on the large plates with 2000 mm width did not exceed 20 nm is fully acceptable form the point of view of expected applications e.g. for architectural glazing.

  11. Comprehensive geophysical survey technique in exploration for deep-buried hydrothermal type uranium deposits in Xiangshan volcanic basin, China

    International Nuclear Information System (INIS)

    Ke, D.

    2014-01-01

    According to recent drilling results, uranium mineralization has been found underground more than 1000 m deep in the Xiangshan volcanic basin, in where uranium exploration has been carried out for over 50 years. This paper presents a comprehensive geophysical survey technique, including audio magnetotelluric method (AMT), high resolution ground magnetic and radon survey, which aim to prospect deep-buried and concealed uranium deposits in Xiangshan volcanic basin. Based on research and application, a comprehensive geophysical technique consisting of data acquisition, processing and interpretation has been established. Concealed rock and ore-controlling structure buried deeper than 1000 m can be detected by using this technique. Moreover, one kind of anti-interference technique of AMT survey is presented, which can eliminate the interference induced by the high-voltage power lines. Result of AMT in Xiangshan volcanic basin is demonstrated as high-low-high mode, which indicates there are three layers in geology. The upper layer with high resistivity is mainly the react of porphyroclastic lava. The middle layer with low resistivity is metamorphic schists or dellenite whereas the lower layer with high resistivity is inferred as granite. The interface between middle and lower layer is recognized as the potential zone for occurrence of uranium deposits. According to the corresponding relation of the resistivity and magnetic anomaly with uranium ore bodies, the tracing model of faults and interfaces between the different rocks, and the forecasting model of advantageous area for uranium deposits have been established. In terms of the forecasting model, some significant sections for uranium deposits were delineated in the west of the Xiangshan volcanic basin. As a result, some achievements on uranium prospecting have been acquired. High grade economic uranium ore bodies have been found in several boreholes, which are located in the forecasted zones. (author)

  12. Electro-spark deposition: A technique for producing wear resistant coatings

    Energy Technology Data Exchange (ETDEWEB)

    Sheldon, G.L. (Washington State Univ., Pullman, WA (USA)); Johnson, R.N. (Westinghouse Hanford Co., Richland, WA (USA))

    1984-12-01

    Electro-spark deposition (ESD) is a coating process using short duration, high current electrical pulses to deposit an electrode material on a metallic substrate. A principal attribute of the process is its ability to apply metallurgically bonded coatings with such a low total heat input that the bulk substrate material remains at or near ambient temperatures. A review of the process is briefly given, then current research using WC-TiC and Cr{sub 3}C{sub 2} electrodes to deposit coatings on Type 316 stainless steel and other substrates is presented. The ESD carbide coatings were found to be exceptionally hard, wear-resistant and spalling-resistant in high-stress rubbing tests. Several applications for nuclear reactor components are described. 17 refs., 18 figs., 1 tab.

  13. Synthesis of dense nano cobalt-hydroxyapatite by modified electroless deposition technique

    Energy Technology Data Exchange (ETDEWEB)

    Mohd Zaheruddin, K., E-mail: zaheruddin@unimap.edu.my; Rahmat, A., E-mail: azmirahmat@unimap.edu.my; Shamsul, J. B., E-mail: sbaharin@unimap.edu.my; Mohd Nazree, B. D., E-mail: nazree@unimap.edu.my; Aimi Noorliyana, H., E-mail: aimiliyana@unimap.edu.my [School of Materials Engineering, Universiti Malaysia Perlis, Kompleks Pusat Pengajian Jejawi Universiti Malaysia Perlis, Taman Muhibbah, Jejawi 02600 Arau Perlis (Malaysia)

    2016-07-19

    Cobalt-hydroxyapatite (Co-HA) composites was successfully prepared by simple electroless deposition process of Co on the surface of hydroxyapatite (HA) particles. Co deposition was carried out in an alkaline bath with sodium hypophosphite as a reducing agent. The electroless process was carried out without sensitization and activation steps. The deposition of Co onto HA was characterized by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). The Co-HA composite powder was compacted and sintered at 1250°C. The Co particles were homogeneously dispersed in the HA matrix after sintering and the mechanical properties of composites was enhanced to 100 % with 3 % wt Co and gradually decreased at higher Co content.

  14. Nanostructured silicon carbon thin films grown by plasma enhanced chemical vapour deposition technique

    Energy Technology Data Exchange (ETDEWEB)

    Coscia, U. [Dipartimento di Fisica, Università di Napoli “Federico II” Complesso Universitario MSA, via Cinthia, 80126 Napoli (Italy); CNISM Unita' di Napoli, Complesso Universitario MSA, via Cinthia, 80126 Napoli (Italy); Ambrosone, G., E-mail: ambrosone@na.infn.it [Dipartimento di Fisica, Università di Napoli “Federico II” Complesso Universitario MSA, via Cinthia, 80126 Napoli (Italy); SPIN-CNR, Complesso Universitario MSA, via Cinthia, 80126 Napoli (Italy); Basa, D.K. [Department of Physics, Utkal University, Bhubaneswar 751004 (India); Rigato, V. [INFN Laboratori Nazionali Legnaro, 35020 Legnaro (Padova) (Italy); Ferrero, S.; Virga, A. [Dipartimento di Scienza Applicata e Tecnologia, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Torino (Italy)

    2013-09-30

    Nanostructured silicon carbon thin films, composed of Si nanocrystallites embedded in hydrogenated amorphous silicon carbon matrix, have been prepared by varying rf power in ultra high vacuum plasma enhanced chemical vapour deposition system using silane and methane gas mixtures diluted in hydrogen. In this paper we have studied the compositional, structural and electrical properties of these films as a function of rf power. It is shown that with increasing rf power the atomic densities of carbon and hydrogen increase while the atomic density of silicon decreases, resulting in a reduction in the mass density. Further, it is demonstrated that carbon is incorporated into amorphous matrix and it is mainly bonded to silicon. The study has also revealed that the crystalline volume fraction decreases with increase in rf power and that the films deposited with low rf power have a size distribution of large and small crystallites while the films deposited with relatively high power have only small crystallites. Finally, the enhanced transport properties of the nanostructured silicon carbon films, as compared to amorphous counterpart, have been attributed to the presence of Si nanocrystallites. - Highlights: • The mass density of silicon carbon films decreases from 2.3 to 2 g/cm{sup 3}. • Carbon is incorporated in the amorphous phase and it is mainly bonded to silicon. • Nanostructured silicon carbon films are deposited at rf power > 40 W. • Si nanocrystallites in amorphous silicon carbon enhance the electrical properties.

  15. Nitrogen rich carbon nitride thin films deposited by hybrid PLD technique

    Czech Academy of Sciences Publication Activity Database

    Jelínek, Miroslav; Kulish, W.; Lančok, Ján; Popov, C.; Bulíř, Jiří; Delplancke-Ogletree, M. P.

    2002-01-01

    Roč. 374, - (2002), s. 207-210 ISSN 1058-725X Institutional research plan: CEZ:AV0Z1010914 Keywords : laser deposition * carbon nitride * radiofrequency discharge * hollow cathode discharge Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.457, year: 2002

  16. Diamond-coated three-dimensional GaN micromembranes: effect of nucleation and deposition techniques

    Czech Academy of Sciences Publication Activity Database

    Ižák, Tibor; Vanko, G.; Babchenko, Oleg; Potocký, Štěpán; Marton, M.; Vojs, M.; Choleva, P.; Kromka, Alexander

    2015-01-01

    Roč. 252, č. 11 (2015), s. 2585-2590 ISSN 0370-1972 R&D Projects: GA ČR(CZ) GP14-16549P Institutional support: RVO:68378271 Keywords : diamond film * GaN micromembranes * microwave chemical vapour deposition * polymer-based nucleation Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.522, year: 2015

  17. Fabrication of Antireflection Nanodiamond Particle Film by the Spin Coating Deposition Technique

    Directory of Open Access Journals (Sweden)

    Chii-Ruey Lin

    2014-01-01

    Full Text Available Diamond-based antireflective (AR coatings were fabricated using a spin coating of diamond suspension at room temperature as nucleation enhancement procedure and microwave plasma enhanced chemical vapour deposition. Various working pressures were used to investigate their effect on the optical characterization of the as-deposited diamond films. Scanning electron microscopy (SEM and atomic forced microscopy (AFM were employed to analyze the surface properties of the diamond films. Raman spectra and transmission electron microscopy (TEM also were used for analysis of the microstructure of the films. The results showed that working pressure had a significant effect on thickness, surface roughness, and wettability of the as-deposited diamond films. Deposited under 35 Torr or working pressure, the film possessed a low surface roughness of 13.8 nm and fine diamond grain sizes of 35 nm. Reflectance measurements of the films also were carried out using UV-Vis spectrometer and revealed a low reflectance value of the diamond films. The achievement demonstrated feasibility of the proposed spin-coating procedure for large scale production and thus opens up a prospect application of diamond film as an AR coating in industrial optoelectronic device.

  18. A comparative study of two advanced spraying techniques for the deposition of biologically active enzyme coatings onto bone-substituting implants

    International Nuclear Information System (INIS)

    Jonge, Lise T. de; Ju, J.; Leeuwenburgh, S.C.G.; Yamagata, Y.; Higuchi, T.; Wolke, J.G.C.; Inoue, K.; Jansen, J.A.

    2010-01-01

    Surface modification of implant materials with biomolecule coatings is of high importance to improve implant fixation in bone tissue. In the current study, we present two techniques for the deposition of biologically active enzyme coatings onto implant materials. The well-established thin film ElectroSpray Deposition (ESD) technique was compared with the SAW-ED technique that combines high-frequency Surface Acoustic Wave atomization with Electrostatic Deposition. By immobilizing the enzyme alkaline phosphatase (ALP) onto implant surfaces, the influence of both SAW-ED and ESD deposition parameters on ALP deposition efficiency and ALP biological activity was investigated. ALP coatings with preserved enzyme activity were deposited by means of both the SAW-ED and ESD technique. The advantages of SAW-ED over ESD include the possibility to spray highly conductive protein solutions, and the 60-times faster deposition rate. Furthermore, significantly higher deposition efficiencies were observed for the SAW-ED technique compared to ESD. Generally, it was shown that protein inactivation is highly dependent on both droplet dehydration and the applied electrical field strength. The current study shows that SAW-ED is a versatile and flexible technique for the fabrication of functionally active biomolecule coatings.

  19. Electroless deposition of metal nanoparticles on graphene with substrate-assisted techniques

    Science.gov (United States)

    Zaniewski, Anna M.; Trimble, Christie J.; Meeks, Veronica; Nemanich, Robert J.

    2015-03-01

    We present the electroless reduction of solution-based metal ions for nanoparticle deposition on a variety of substrates. The substrates include graphene-coated metals, insulators, doped semiconductors, and patterned ferroelectrics. We find that the metal ions are spontaneously reduced on a wide variety of graphene substrates, and the substrates play a large role in the nanoparticle coverage. For example, the reduction of gold chloride to gold nanoparticles on graphene/lithium niobate results in 3% nanoparticle coverage compared to 20% coverage on graphene/silicon and 60% on graphene/copper. Given that the work function of graphene is approximately 4.4eV, the Fermi level is -0.1 V vs the normal hydrogen electrode (NHE). Since the reduction potential of gold chloride is +1.002 V, the spontaneous transfer of electrons from the graphene to the metal ion is energetically favorable. However, we find substrates with similar work functions nevertheless result in varied deposition rates, which we attribute to electron availability. We also find that patterned ferrolectrics can be used as a template for patterned nanoparticle deposition, with and without graphene. This work is supported by the National Science Foundation under Grant # DMR-1206935.

  20. Thick CrN/NbN multilayer coating deposited by cathodic arc technique

    Energy Technology Data Exchange (ETDEWEB)

    Araujo, Juliano Avelar; Tschiptschin, Andre Paulo; Souza, Roberto Martins, E-mail: antschip@usp.br [Universidade de Sao Paulo (USP), SP (Brazil); Lima, Nelson Batista de [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2017-01-15

    The production of tribological nanoscale multilayer CrN/NbN coatings up to 6 μm thick by Sputtering/HIPIMS has been reported in literature. However, high demanding applications, such as internal combustion engine parts, need thicker coatings (>30 μm). The production of such parts by sputtering would be economically restrictive due to low deposition rates. In this work, nanoscale multilayer CrN/NbN coatings were produced in a high-deposition rate, industrial-size, Cathodic Arc Physical Vapor Deposition (ARC-PVD) chamber, containing three cathodes in alternate positions (Cr/ Nb/Cr). Four 30 μm thick NbN/CrN multilayer coatings with different periodicities (20, 10, 7.5 and 4 nm) were produced. The coatings were characterized by X-Ray Diffraction (XRD) and Transmission Electron Microscopy (TEM). The multilayer coating system was composed of alternate cubic rock salt CrN and NbN layers, coherently strained due to lattice mismatch. The film grew with columnar morphology through the entire stratified structure. The periodicities adopted were maintained throughout the entire coating. The 20 nm periodicity coating showed separate NbN and CrN peaks in the XRD patterns, while for the lower periodicity (≤10nm) coatings, just one intermediate lattice (d-spacing) was detected. An almost linear increase of hardness with decreasing bilayer period indicates that interfacial effects can dominate the hardening mechanisms. (author)

  1. Studies on methods and techniques of weak information extraction and integrated evaluation for sandstone-type uranium deposits

    International Nuclear Information System (INIS)

    Han Shaoyang; Ke Dan; Hou Huiqun; Hu Shuiqing

    2004-01-01

    Weak information extraction and integrated evaluation for sandstone-type uranium deposits are currently one of the important research contents in uranium exploration. Through several years researches, the authors put forward the meaning of aeromagnetic and aeroradioactive weak information extraction, study the formation theories of aeromagnetic and aeroradioactive weak information and establish effective mathematic models for weak information extraction. Based on GIS software, models of weak information extraction are actualized and the expert-grading model for integrated evaluation is developed. The trial of aeromagnetic and aeroradioactive weak information and integrated evaluation of uranium resources are completed by using GIS software in the study area. The researchful results prove that techniques of weak information extraction and integrated evaluation may further delineate the prospective areas of sandstone-type uranium deposits rapidly and improve the predicitive precision. (authors)

  2. Photodetectors based on carbon nanotubes deposited by using a spray technique on semi-insulating gallium arsenide.

    Science.gov (United States)

    Melisi, Domenico; Nitti, Maria Angela; Valentini, Marco; Valentini, Antonio; Ligonzo, Teresa; De Pascali, Giuseppe; Ambrico, Marianna

    2014-01-01

    In this paper, a spray technique is used to perform low temperature deposition of multi-wall carbon nanotubes on semi-insulating gallium arsenide in order to obtain photodectors. A dispersion of nanotube powder in non-polar 1,2-dichloroethane is used as starting material. The morphological properties of the deposited films has been analysed by means of electron microscopy, in scanning and transmission mode. Detectors with different layouts have been prepared and current-voltage characteristics have been recorded in the dark and under irradiation with light in the range from ultraviolet to near infrared. The device spectral efficiency obtained from the electrical characterization is finally reported and an improvement of the photodetector behavior due to the nanotubes is presented and discussed.

  3. Comparison of CdS films deposited by different techniques: Effects on CdTe solar cell

    International Nuclear Information System (INIS)

    Lee, Jaehyeong

    2005-01-01

    Polycrystalline cadmium sulfide (CdS) thin-films were deposited on glass substrate by chemical bath deposition (CBD) and vacuum evaporation (VE) techniques. VE-CdS films consisted primarily of hexagonal phase, whereas CBD CdS films containing primarily the cubic form. VE-grown films were shown to have better crystallinity than CBD-grown films. The grain size of the CBD films is smaller than the ones of VE films. VE-CdS films exhibited relatively high transmittance in the above-gap region and band gap compared with CBD films. However, CdTe solar cells with these low quality CBD-CdS layers yield higher and more stable characteristics. Current-voltage-temperature measurements showed that the current transport for both cells was controlled by both tunneling and interface recombination but the cells with CBD-CdS displayed less tunneling

  4. Noninvasive radioisotopic technique for detection of platelet deposition in mitral valve prostheses and quantitation of visceral microembolism in dogs

    International Nuclear Information System (INIS)

    Dewanjee, M.K.; Fuster, V.; Rao, S.A.; Forshaw, P.L.; Kaye, M.P.

    1983-01-01

    A noninvasive technique has been developed in the dog model for imaging, with a gamma camera, the platelet deposition on Bjoerk-Shiley mitral valve prostheses early postoperatively. At 25 hours after implantation of the prosthesis and 24 hours after intravenous administration of 400 to 500 microCi of platelets labeled with indium-111, the platelet deposition in the sewing ring and perivalvular cardiac tissue can be clearly delineated in a scintiphotograph. An in vitro technique was also developed for quantitation of visceral microemboli in brain, lungs, kidneys, and other tissues. Biodistribution of the labeled platelets was quantitated, and the tissue/blood radioactivity ratio was determined in 22 dogs in four groups: unoperated normal dogs, sham-operated dogs, prosthesis-implanted dogs, and prosthesis-implanted dogs treated with dipyridamole before and aspirin and dipyridamole immediately after operation. Fifteen to 20% of total platelets were consumed as a consequence of the surgical procedure. On quantitation, we found that platelet deposition on the components of the prostheses was significantly reduced in prosthesis-implanted animals treated with dipyridamole and aspirin when compared with prosthesis-implanted, untreated dogs. All prosthesis-implanted animals considered together had a twofold to fourfold increase in tissue/blood radioactivity ratio in comparison with unoperated and sham-operated animals, an indication that the viscera work as filters and trap platelet microemboli that are presumably produced in the region of the mitral valve prostheses. In the dog model, indium-111-labeled platelets thus provide a sensitive marker for noninvasive imaging of platelet deposition on mechanical mitral valve prostheses, in vitro evaluation of platelet microembolism in viscera, in vitro quantitation of surgical consumption of platelets, and evaluation of platelet-inhibitor drugs

  5. Effects of Sputtering Parameters on AlN Film Growth on Flexible Hastelloy Tapes by Two-Step Deposition Technique.

    Science.gov (United States)

    Peng, Bin; Gong, Dongdong; Zhang, Wanli; Jiang, Jianying; Shu, Lin; Zhang, Yahui

    2016-08-10

    AlN thin films were deposited on flexible Hastelloy tapes and Si (100) substrate by middle-frequency magnetron sputtering. A layer of Y₂O₃ films was used as a buffer layer for the Hastelloy tapes. A two-step deposition technique was used to prepare the AlN films. The effects of deposition parameters such as sputtering power, N₂/Ar flow rate and sputtering pressure on the microstructure of the AlN thin films were systematically investigated. The results show that the dependency of the full width at half maximum (FWHM) of AlN/Y₂O₃/Hastelloy on the sputtering parameters is similar to that of AlN/Si (100). The FWHM of the AlN (002) peak of the prepared AlN films decreases with increasing sputtering power. The FWHM decreases with the increase of the N₂/Ar flow rate or sputtering pressure, and increases with the further increase of the N₂/Ar flow rate or sputtering pressure. The FWHM of the AlN/Y₂O₃/Hastelloy prepared under optimized parameters is only 3.7° and its root mean square (RMS) roughness is 5.46 nm. Based on the experimental results, the growth mechanism of AlN thin films prepared by the two-step deposition process was explored. This work would assist us in understanding the AlN film's growth mechanism of the two-step deposition process, preparing highly c-axis-oriented AlN films on flexible metal tapes and developing flexible surface acoustic wave (SAW) sensors from an application perspective.

  6. Investigation of Non-Vacuum Deposition Techniques in Fabrication of Chalcogenide-Based Solar Cell Absorbers

    KAUST Repository

    Alsaggaf, Ahmed

    2015-07-01

    The environmental challenges are increasing, and so is the need for renewable energy. For photovoltaic applications, thin film Cu(In,Ga)(S,Se)2 (CIGS) and CuIn(S,Se)2 (CIS) solar cells are attractive with conversion efficiencies of more than 20%. However, the high-efficiency cells are fabricated using vacuum technologies such as sputtering or thermal co-evaporation, which are very costly and unfeasible at industrial level. The fabrication involves the uses of highly toxic gases such as H2Se, adding complexity to the fabrication process. The work described here focused on non-vacuum deposition methods such as printing. Special attention has been given to printing designed in a moving Roll-to-Roll (R2R) fashion. The results show potential of such technology to replace the vacuum processes. Conversion efficiencies for such non-vacuum deposition of Cu(In,Ga)(S,Se)2 solar cells have exceeded 15% using hazardous chemicals such as hydrazine, which is unsuitable for industrial scale up. In an effort to simplify the process, non-toxic suspensions of Cu(In,Ga)S2 molecular-based precursors achieved efficiencies of ~7-15%. Attempts to further simplify the selenization step, deposition of CuIn(S,Se)2 particulate solutions without the Ga doping and non-toxic suspensions of Cu(In,Ga)Se2 quaternary precursors achieved efficiencies (~1-8%). The contribution of this research was to provide a new method to monitor printed structures through spectral-domain optical coherence tomography SD-OCT in a moving fashion simulating R2R process design at speeds up to 1.05 m/min. The research clarified morphological and compositional impacts of Nd:YAG laser heat-treatment on Cu(In,Ga)Se2 absorber layer to simplify the annealing step in non-vacuum environment compatible to R2R. Finally, the research further simplified development methods for CIGS solar cells based on suspensions of quaternary Cu(In,Ga)Se2 precursors and ternary CuInS2 precursors. The methods consisted of post deposition reactive

  7. A novel deposition technique for switchable vanadium sesquioxide (V sub 2 O sub 3 ) thin films

    Energy Technology Data Exchange (ETDEWEB)

    Case, F.C. (LTV Missiles and Electronics Group, Research Department, MS WT-50, Dallas, Texas 75265-0003 (USA))

    1991-05-01

    V{sub 2}O{sub 3} is a phase transition material, which, like other oxides of vanadium, undergoes large changes in optical and electrical properties upon switching from the semiconductor to metal state. The transition in V{sub 2}O{sub 3} occurs at temperatures well below that of oxides in the same family, namely near 150--170 K, making it attractive for a number of low-temperature applications. This material has been deposited by a variety of methods, including chemical vapor transport, rf sputtering of a stoichiometric target, pyrolysis, and heat treatment of a sputtered vanadium oxide film. Thin films of this material have also been prepared by the reduction of predeposited VO{sub 2} thin films, requiring the flow of hazardous gases such as hydrogen or carbon monoxide over the sample, which is held at high temperatures in excess of 700 {degree}C. A direct synthesis method for the deposition of high quality V{sub 2}O{sub 3} thin films with low infrared absorption and resistivity change of more than six orders of magnitude is described. Optical, resistivity, and morphological characteristics of this material are discussed.

  8. Patterning of gold nanoparticles on fluoropolymer films by using patterned surface grafting and layer-by-layer deposition techniques.

    Science.gov (United States)

    Jung, Chang-Hee; Hwang, In-Tae; Jung, Chan-Hee; Choi, Jae-Hak; Kwon, Oh-Sun; Shin, Kwanwoo

    2013-09-11

    The patterning of gold nanoparticles (GNPs) on the surface of a fluoropolymer substrate by using patterned surface grafting and layer-by-layer deposition techniques is described. The surface of a poly(tetrafluoroethylene-co-perfluorovinyl ether) (PFA) substrate was selectively implanted with 150 keV proton ions. Peroxide groups were successfully formed on the implanted PFA surface, and their concentration depended on the fluence. Acrylic acid was graft polymerized onto the implanted regions of the PFA substrate, resulting in well-defined patterns of poly(acrylic acid) (PAA) on the PFA substrate. The surface properties of the PAA-patterned PFA surface, such as chemical compositions, wettability, and morphology, were investigated. The surface analysis results revealed that PAA was definitely present on the implanted regions of the PFA surface, and the degree of grafting was dependent on three factors: fluence, grafting time, and monomer concentration. Furthermore, GNP patterns were generated on the prepared PAA-patterned PFA surface by layer-by-layer deposition of GNPs and poly(diallyldimethyl ammonium chloride). The multilayers of GNPs were deposited only onto the PAA-grafted regions separated by bare PFA regions, and the resulting GNP patterns exhibited good electrical conductivity.

  9. Fabrication and characterisation of ligand-functionalised ultrapure monodispersed metal nanoparticle nanoassemblies employing advanced gas deposition technique

    Science.gov (United States)

    Geremariam Welearegay, Tesfalem; Cindemir, Umut; Österlund, Lars; Ionescu, Radu

    2018-02-01

    Here, we report for the first time the fabrication of ligand-functionalised ultrapure monodispersed metal nanoparticles (Au, Cu, and Pt) from their pure metal precursors using the advanced gas deposition technique. The experimental conditions during nanoparticle formation were adjusted in order to obtain ultrafine isolated nanoparticles on different substrates. The morphology and surface analysis of the as-deposited metal nanoparticles were investigated using scanning electron microscopy, x-ray diffraction and Fourier transform infra-red spectroscopy, which demonstrated the formation of highly ordered pure crystalline nanoparticles with a relatively uniform size distribution of ∼10 nm (Au), ∼4 nm (Cu) and ∼3 nm (Pt), respectively. A broad range of organic ligands containing thiol or amine functional groups were attached to the nanoparticles to form continuous networks of nanoparticle-ligand nanoassemblies, which were characterised by scanning electron microscopy and x-ray photoelectron spectroscopy. The electrical resistance of the functional nanoassemblies deposited in the gap spacing of two microfabricated parallel Au electrodes patterned on silicon substrates ranged between tens of kΩ and tens of MΩ, which is suitable for use in many applications including (bio)chemical sensors, surface-enhanced Raman spectroscopy and molecular electronic rectifiers.

  10. Effect of active screen plasma nitriding pretreatment on wear behavior of TiN coating deposited by PACVD technique

    Energy Technology Data Exchange (ETDEWEB)

    Raoufi, M., E-mail: raoufi@iust.ac.ir [School of Metallurgical Engineering, Iran University of Science and Technology, Tehran (Iran, Islamic Republic of); Mirdamadi, Sh. [School of Metallurgical Engineering, Iran University of Science and Technology, Tehran (Iran, Islamic Republic of); Mahboubi, F. [Department of Mining and Metallurgical Engineering, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Ahangarani, Sh. [Advanced Materials and Renewable Energies Dep., Iranian Research Organization for Science and Technology (Iran, Islamic Republic of); Mahdipoor, M.S. [Department of Mining and Metallurgical Engineering, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Elmkhah, H. [Department of Metallurgical Engineering, Tarbiat Modares University, Tehran (Iran, Islamic Republic of)

    2012-08-01

    Titanium based alloys are used extensively for improving wear properties of different parts due to their high hardness contents. Titanium nitride (TiN) is among these coatings which can be deposited on surface using various techniques such as CVD, PVD and PACVD. Their weak interface with substrate is one major drawback which can increase the total wear in spite of favorite wear behavior of TiN. Disc shaped samples from AISI H13 (DIN 1.2344) steel were prepared in this study. Single TiN coating was deposited on some of them while others have experienced a TiN deposition by active screen plasma nitriding (ASPN). Hardness at the surface and depth of samples was measured through Vickers micro hardness test which revealed 1810 Hv hardness as the maximum values for a dual-layered ASPN-TiN. Pin-on-disc wear test was done in order to study the wear mechanism. In this regard, the wear behavior of samples was investigated against pins from 100Cr6 (Din 1.3505) bearing steel and tungsten carbide-cobalt (WC-Co) steel. It was evidenced that the dual-layer ASPN-TiN coating has shown the least weight loss with the best wearing behavior because of its high hardness values, stable interface and acceptable resistance against peeling during wearing period.

  11. Influence of the deposition technique on the structural and optical properties of amorphous As-S films

    International Nuclear Information System (INIS)

    Gonzalez-Leal, J.M.; Stuchlik, M.; Vlcek, M.; Jimenez-Garay, R.; Marquez, E.

    2005-01-01

    Amorphous chalcogenide films of stoichiometric composition As 40 S 60 have been prepared by three different deposition techniques, namely, vacuum thermal evaporation, plasma-enhanced chemical vapour deposition (PECVD) and spin coating. Indications of film-thickness inhomogeneities were found in all samples. Thermally evaporated and chemically deposited samples showed wedge-shaped surface profiles, while significant surface roughness was evidenced in the spin-coated ones. Refractive-index values of the film samples were obtained, with accuracy better than 1%, by using the envelope method most suitable for each particular film surface profile. Structural information of the samples has been gained from X-ray diffraction experiments, and also inferred from the analysis of the dispersion of the refractive index, on the basis of a single-oscillator model. Analysis of the optical absorption spectra allowed both calculating the optical band gaps and estimating the localised-state tail width of these semiconducting films. In addition, information about the degree of structural randomness of these thin-film amorphous alloys was also obtained from this analysis, which is in good agreement with the conclusions derived from the X-ray diffraction results

  12. Thin films of NdFeB deposited by PLD technique

    International Nuclear Information System (INIS)

    Constantinescu, C.; Scarisoreanu, N.; Moldovan, A.; Dinescu, M.; Petrescu, L.; Epureanu, G.

    2007-01-01

    Neodymium-iron-boron (NdFeB) is a material with important magnetic properties, mostly used in permanent magnet fabrication. Thin layers of NdFeB are needed for miniaturization in electrical engineering, electronics and for high-tech devices. In this paper we applied pulsed lased deposition (PLD) in vacuum for obtaining thin films of NdFeB from stoichiometric targets. The influence of different buffer layers and of the laser parameters (wavelength and fluence) on the NdFeB structures, composition and magnetic properties have been investigated. The obtained structures were characterized by atomic force microscopy (AFM) and optical microscopy. Vibrating sample magnetometry (VSM) has been performed for specific magnetic characterization

  13. Thin films of NdFeB deposited by PLD technique

    Energy Technology Data Exchange (ETDEWEB)

    Constantinescu, C. [National Institute for Laser, Plasma and Radiation Physics, P.O. Box MG 16, RO-077125 Magurele, Bucharest (Romania); Scarisoreanu, N. [National Institute for Laser, Plasma and Radiation Physics, P.O. Box MG 16, RO-077125 Magurele, Bucharest (Romania); Moldovan, A. [National Institute for Laser, Plasma and Radiation Physics, P.O. Box MG 16, RO-077125 Magurele, Bucharest (Romania); Dinescu, M. [National Institute for Laser, Plasma and Radiation Physics, P.O. Box MG 16, RO-077125 Magurele, Bucharest (Romania)]. E-mail: dinescum@ifin.nipne.ro; Petrescu, L. [Department of Electrical Engineering, ' Politehnica' University of Bucharest, 313 Spl. Independentei, 060042 Bucharest (Romania); Epureanu, G. [Department of Electrical Engineering, ' Politehnica' University of Bucharest, 313 Spl. Independentei, 060042 Bucharest (Romania)

    2007-07-31

    Neodymium-iron-boron (NdFeB) is a material with important magnetic properties, mostly used in permanent magnet fabrication. Thin layers of NdFeB are needed for miniaturization in electrical engineering, electronics and for high-tech devices. In this paper we applied pulsed lased deposition (PLD) in vacuum for obtaining thin films of NdFeB from stoichiometric targets. The influence of different buffer layers and of the laser parameters (wavelength and fluence) on the NdFeB structures, composition and magnetic properties have been investigated. The obtained structures were characterized by atomic force microscopy (AFM) and optical microscopy. Vibrating sample magnetometry (VSM) has been performed for specific magnetic characterization.

  14. Deposit of thin films of nitrided amorphous carbon using the laser ablation technique

    International Nuclear Information System (INIS)

    Rebollo, P.B.; Escobar A, L.; Camps C, E.; Haro P, E.; Camacho L, M.A.; Muhl S, S.

    2000-01-01

    It is reported the synthesis and characterization of thin films of amorphous carbon (a-C) nitrided, deposited by laser ablation in a nitrogen atmosphere at pressures which are from 4.5 x 10 -4 Torr until 7.5 x 10 -2 Torr. The structural properties of the films are studied by Raman spectroscopy obtaining similar spectra at the reported for carbon films type diamond. The study of behavior of the energy gap and the ratio nitrogen/carbon (N/C) in the films, shows that the energy gap is reduced when the nitrogen incorporation is increased. It is showed that the refraction index of the thin films diminish as nitrogen pressure is increased, indicating the formation of graphitic material. (Author)

  15. Carbon thin films deposited by the magnetron sputtering technique using cobalt, copper and nickel as buffer-layers

    International Nuclear Information System (INIS)

    Costa e Silva, Danilo Lopes

    2015-01-01

    In this work, carbon thin films were produced by the magnetron sputtering technique using single crystal substrates of alumina c-plane (0001) and Si (111) and Si (100) substrates, employing Co, Ni and Cu as intermediate films (buffer-layers). The depositions were conducted in three stages, first with cobalt buffer-layers where only after the production of a large number of samples, the depositions using cooper buffer-layers were carried out on Si substrates. Then, depositions were performed with nickel buffer layers using single-crystal alumina substrates. The crystallinity of the carbon films was evaluated by using the technique of Raman spectroscopy and, then, by X-ray diffraction (XRD). The morphological characterization of the films was performed by scanning electron microscopy (SEM and FEG-SEM) and high-resolution transmission electron microscopy (HRTEM). The XRD peaks related to the carbon films were observed only in the results of the samples with cobalt and nickel buffer-layers. The Raman spectroscopy showed that the carbon films with the best degree of crystallinity were the ones produced with Si (111) substrates, for the Cu buffers, and sapphire substrates for the Ni and Co buffers, where the latter resulted in a sample with the best crystallinity of all the ones produced in this work. It was observed that the cobalt has low recovering over the alumina substrates when compared to the nickel. Sorption tests of Ce ions by the carbon films were conducted in two samples and it was observed that the sorption did not occur probably because of the low crystallinity of the carbon films in both samples. (author)

  16. Applications of prospecting geochemical techniques to the search for and to the study of uranium deposits in metropolitan France

    International Nuclear Information System (INIS)

    Grimbert, Arnold

    1957-01-01

    After having recalled facts which leaded the CEA to use new geochemical techniques for the prospecting of uranium deposits through sampling and analysis of soils and waters, the author describes the organisation and methods implemented for this prospecting activity: team composition for sampling and analysis, role of each engineer and technician in the prospecting stages (preliminary study, routine prospecting, result interpretation), sampling and analysis processes. He also reports campaigns of geochemical prospecting: study of the La Chapelle Largeau deposit (objectives, geological context, preliminary study, routine prospecting, study of geochemical anomalies), tactical research on Verneix indices (study of radioactivity anomaly discovered by radio-prospecting), strategical searches in a non prospected area in the South of Avallon. The author discusses the issues of efficiency and cost price of this geochemical prospecting technique in soils and in waters. Appendices present the equipment and operation modality for soil sampling, and for soil sample preparation, and principles, equipment and products for soil analysis and for water analysis [fr

  17. Growth, surface treatment and characterization of polycrystalline lead iodide thick films prepared using close space deposition technique

    International Nuclear Information System (INIS)

    Zhu, Xinghua; Sun, Hui; Yang, Dingyu; Zheng, Xiaolin

    2012-01-01

    Lead iodide (PbI 2 ) polycrystalline thick films were fabricated on glass substrates with a conductive indium–tin-oxide layer using a close space deposition technique. The morphology of the as-deposited PbI 2 films is typically and highly oriented polycrystalline structure, made up of microcrystal platelets upright on the substrate plane. Two techniques including the surface mechanical cutting and after-growth cadmium telluride coating were employed to improve the films′ surface properties. It was shown that both of the film surface treatment methods markedly decreased the dark current of PbI 2 films. The photo-to-dark current ratio of about 2.05 under 241 Am γ-ray source with activity of 2.78 μCi irradiation was obtained from the film treated using both surface cutting and after-growth CdTe coating. Charge transport characteristics of these films were measured and the hole mobility 7.7×10 −2 –1.67×10 −1 cm 2 /V s was estimated.

  18. ELECTRICAL FURNACE FOR PRODUCING CARBIDE COATINGS USING THE THERMOREACTIVE DEPOSITION/DIFFUSION TECHNIQUE

    Directory of Open Access Journals (Sweden)

    FABIO CASTILLEJO

    2011-01-01

    the presence of VC and NbC, and as MEB results clearly show, the formation of regular thickness coatings. The results obtained allow for assessing that the designed and built furnace fulfills the requirements of the TRD technique for obtaining different types of hard coatings.

  19. Comparative study of CdTe sources used for deposition of CdTe thin films by close spaced sublimation technique

    Directory of Open Access Journals (Sweden)

    Wagner Anacleto Pinheiro

    2006-03-01

    Full Text Available Unlike other thin film deposition techniques, close spaced sublimation (CSS requires a short source-substrate distance. The kind of source used in this technique strongly affects the control of the deposition parameters, especially the deposition rate. When depositing CdTe thin films by CSS, the most common CdTe sources are: single-crystal or polycrystalline wafers, powders, pellets or pieces, a thick CdTe film deposited onto glass or molybdenum substrate (CdTe source-plate and a sintered CdTe powder. In this work, CdTe thin films were deposited by CSS technique from different CdTe sources: particles, powder, compact powder, a paste made of CdTe and propylene glycol and source-plates (CdTe/Mo and CdTe/glass. The largest deposition rate was achieved when a paste made of CdTe and propylene glycol was used as the source. CdTe source-plates led to lower rates, probably due to the poor heat transmission, caused by the introduction of the plate substrate. The results also showed that compacting the powder the deposition rate increases due to the better thermal contact between powder particles.

  20. Atomic force microscopy and Langmuir–Blodgett monolayer technique to assess contact lens deposits and human meibum extracts

    Directory of Open Access Journals (Sweden)

    Sarah Hagedorn

    2015-07-01

    Conclusions: MGD and non-MGD participant-worn CL deposition were found to differ in type, amount, and pattern of lens deposits. Lipids from MGD participants deposited irregularly whereas lipids from non-MGD participants showed more uniformity.

  1. Nuclear techniques for in situ evaluation of coal and mineral deposits

    International Nuclear Information System (INIS)

    Borsaru, M.

    1993-01-01

    This paper reviews developments in in situ analysis of minerals and coal by nuclear borehole logging. Developments in the oil, gas and uranium industries are not discussed in the present paper unless they have direct applications in the mineral industry (e.g. multi-element analysis and development of spectral litho-density tools). The review covers techniques developed mostly in the last decade and is based on work published in North America, Europe and Australia. (author)

  2. Magnetotransport study of granular chromium dioxide thin films prepared by the chemical vapor deposition technique

    International Nuclear Information System (INIS)

    Liang, J.-J.; Lee, S.F.; Yao, Y.D.; Wu, C.C.; Shyu, S.G.; Yu, C.

    2002-01-01

    The temperature-dependent magnetotransport properties of granular chromium dioxide (CrO 2 ) films with grain size about 1 μm grown by chemical vapor deposition on Si(0 0 1) substrates has been studied over a temperature range from 2 to 300 K. The magnetoresistance (MR) of about 20% at T=2 K decreases very fast with increasing temperature as a result of the rapid increase of the spin-independent hopping channel, whilst the temperature-dependent MR is almost the same for samples after 100 days annealing in air at room temperature, and its electrical resistivity at room temperature increases from roughly 50 to >75 μΩ m. The contribution to the conductance at T 1.33 . It becomes a poor metal at temperatures >160 K and its resistance follows R∼T 2 exp(-Δ/T). We have shown experimentally that the room temperature annealing results in the decomposition of CrO 2 into Cr 2 O 3 mainly near the surface of the films

  3. Numerical Simulation of Molten Flow in Directed Energy Deposition Using an Iterative Geometry Technique

    Science.gov (United States)

    Vincent, Timothy J.; Rumpfkeil, Markus P.; Chaudhary, Anil

    2018-03-01

    The complex, multi-faceted physics of laser-based additive metals processing tends to demand high-fidelity models and costly simulation tools to provide predictions accurate enough to aid in selecting process parameters. Of particular difficulty is the accurate determination of melt pool shape and size, which are useful for predicting lack-of-fusion, as this typically requires an adequate treatment of thermal and fluid flow. In this article we describe a novel numerical simulation tool which aims to achieve a balance between accuracy and cost. This is accomplished by making simplifying assumptions regarding the behavior of the gas-liquid interface for processes with a moderate energy density, such as Laser Engineered Net Shaping (LENS). The details of the implementation, which is based on the solver simpleFoam of the well-known software suite OpenFOAM, are given here and the tool is verified and validated for a LENS process involving Ti-6Al-4V. The results indicate that the new tool predicts width and height of a deposited track to engineering accuracy levels.

  4. Structure and Properties of Diamond-Like Carbon Films Deposited by PACVD Technique on Light Alloys

    Directory of Open Access Journals (Sweden)

    Tański T.

    2016-09-01

    Full Text Available The investigations presented in this paper describe surface treatment performed on samples of heat-treated cast magnesium and aluminium alloy. The structure and chemical composition as well as the functional and mechanical properties of the obtained gradient/monolithic films were analysed by high resolution transmission electron microscopy and scanning electron microscopy, Raman spectroscopy, the ball-on-disk tribotester and scratch testing. Moreover, investigation of the electrochemical corrosion behaviour of the samples was carried out by means of potentiodynamic polarisation curves in 1-M NaCl solution. The coatings produced by chemical vapour deposition did not reveal any delamination or defects and they adhere closely to the substrate. The coating thickness was in a range of up to 2.5 microns. Investigations using Raman spectra of the DLC films confirmed a multiphase character of the diamond-like carbon layer, revealing the sp2 and sp3 electron hybridisation responsible for both the hardness and the friction coefficient. The best wear resistance test results were obtained for the magnesium alloy substrate - AZ61, for which the measured value of the friction path length was equal to 630 m.

  5. Membranes produced by plasma enhanced chemical vapor deposition technique for low temperature fuel cell applications

    Science.gov (United States)

    Ennajdaoui, Aboubakr; Roualdes, Stéphanie; Brault, Pascal; Durand, Jean

    A plasma polymerization process using a continuous glow discharge has been implemented for preparing proton conducting membranes from trifluoromethane sulfonic acid and styrene. The chemical and physical structure of plasma membranes has been investigated using FTIR and SEM. The films are homogeneous with a good adhesion on commercial gas diffusion layer (E-Tek ®). Their deposition rate can be increased with increasing flow rate and input power. The thermogravimetric analysis under air of plasma polymers has showed a thermal stability up to 140 °C. Compared to the pulsed glow discharge studied in a previous paper, the continuous glow discharge has enabled to enhance the proton conductivity of membranes by a factor 3 (up to 1.7 mS cm -1). Moreover, the low methanol permeability (methanol diffusion coefficient down to 5 × 10 -13 m 2 s -1) of membranes has been confirmed by this study. In an industrial context, a reactor prototype has been developed to manufacture by plasma processes all active layers of fuel cell cores to be integrated in original compact PEMFC or DMFC.

  6. Identification of sources of tar balls deposited along the Goa coast, India, using fingerprinting techniques.

    Science.gov (United States)

    Suneel, V; Vethamony, P; Zakaria, M P; Naik, B G; Prasad, K V S R

    2013-05-15

    Deposition of tar balls along the coast of Goa, India is a common phenomenon during the southwest monsoon. Representative tar ball samples collected from various beaches of Goa and one Bombay High (BH) crude oil sample were subjected to fingerprint analysis based on diagnostic ratios of n-alkane, biomarkers of pentacyclic tri-terpanes and compound specific stable carbon isotope (δ¹³C) analysis to confirm the source. The results were compared with the published data of Middle East Crude Oil (MECO) and South East Asian Crude Oil (SEACO). The results revealed that the tar balls were from tanker-wash derived spills. The study also confirmed that the source is not the BH, but SEACO. The present study suggests that the biomarkers of alkanes and hopanes coupled with stable carbon isotope analysis act as a powerful tool for tracing the source of tar balls, particularly when the source specific biomarkers fail to distinguish the source. Copyright © 2013 Elsevier Ltd. All rights reserved.

  7. Identification of sources of tar balls deposited along the Goa coast, India, using fingerprinting techniques

    International Nuclear Information System (INIS)

    Suneel, V.; Vethamony, P.; Zakaria, M.P.; Naik, B.G.; Prasad, K.V.S.R.

    2013-01-01

    Highlights: ► This is first fingerprinting study in India on identification of source of tar balls. ► Tar balls were formed from tanker-wash spills and they resemble floating tar ball. ► δ 13 C values of Bombay High crude oil and the present tar balls do not match. ► Compound specific stable carbon isotope analysis confirmed the source of tar balls. ► Source is confirmed as the South East Asian Crude Oil and not the Bombay High crude. -- Abstract: Deposition of tar balls along the coast of Goa, India is a common phenomenon during the southwest monsoon. Representative tar ball samples collected from various beaches of Goa and one Bombay High (BH) crude oil sample were subjected to fingerprint analysis based on diagnostic ratios of n-alkane, biomarkers of pentacyclic tri-terpanes and compound specific stable carbon isotope (δ 13 C) analysis to confirm the source. The results were compared with the published data of Middle East Crude Oil (MECO) and South East Asian Crude Oil (SEACO). The results revealed that the tar balls were from tanker-wash derived spills. The study also confirmed that the source is not the BH, but SEACO. The present study suggests that the biomarkers of alkanes and hopanes coupled with stable carbon isotope analysis act as a powerful tool for tracing the source of tar balls, particularly when the source specific biomarkers fail to distinguish the source

  8. Structural and optical properties of Zn–In–Te thin films deposited by thermal evaporation technique

    Energy Technology Data Exchange (ETDEWEB)

    Güllü, H.H.; Bayraklı, Ö.; Candan, İ. [Department of Physics, Middle East Technical University, GUNAM, 06800 Ankara (Turkey); Coşkun, E. [Department of Physics, Middle East Technical University, GUNAM, 06800 Ankara (Turkey); Department of Physics, Çanakkale Onsekiz Mart University, 17100 Çanakkale (Turkey); Parlak, M., E-mail: parlak@metu.edu.tr [Department of Physics, Middle East Technical University, GUNAM, 06800 Ankara (Turkey)

    2013-07-25

    Highlights: •The new ternary compound Zn–In–Te (ZIT) has been studied for photovoltaic device applications as an absorber layer. •ZIT thin films were deposited by thermal evaporation of stoichiometric sintered polycrystalline powder. •The optical constants were calculated by using different methods, (SOM), Envelope Model (EM) and Cauchy Method. •Urbach energies were calculated and the increasing band tail energies were observed with increasing annealing temperature. -- Abstract: Annealing effects on structural and optical properties of the thermally evaporated Zn–In–Te (ZIT) thin films have been investigated. The structural and the compositional analyses were carried out by means of X-ray diffraction (XRD) and energy dispersive X-ray analysis (EDXA). The as-grown and annealed ZIT films had polycrystalline structure and the preferred orientation changed from (2 2 0) to (1 1 2) direction with increasing annealing temperature. The optical properties and constants were determined by transmittance measurements in the wavelength range of 200–2000 nm. The effect of annealing on the optical parameters was determined by using Single Oscillator Model (SOM), Envelope Model (EM) and Cauchy Method. The absorbance studies revealed that the films had three distinct transitions in the high absorption region because of the tetragonal distortion, and that was used to evaluate the splitting energies of crystal-field and spin–orbit splitting. The fundamental optical band gap values were found to be lying in the range of 1.51 and 1.72 eV and the notable change of the band gaps due to annealing temperatures was observed. Finally, the Urbach energies were calculated and it was observed that the band tail energies were increasing with increasing annealing temperature.

  9. Photocatalytic efficiency of reusable ZnO thin films deposited by sputtering technique

    Energy Technology Data Exchange (ETDEWEB)

    Ahumada-Lazo, R.; Torres-Martínez, L.M. [Universidad Autónoma de Nuevo León, Facultad de Ingeniería Civil, Departamento de Ecomateriales y Energía, Av. Universidad S/N Ciudad Universitaria, San Nicolás de los Garza, Nuevo León C.P. 66450, México (Mexico); Ruíz-Gómez, M.A. [Universidad Autónoma de Nuevo León, Facultad de Ingeniería Civil, Departamento de Ecomateriales y Energía, Av. Universidad S/N Ciudad Universitaria, San Nicolás de los Garza, Nuevo León C.P. 66450, México (Mexico); Departmento de Física Aplicada, CINVESTAV-IPN, Antigua Carretera a Progreso km 6, Mérida, Yucatán 97310, México (Mexico); Vega-Becerra, O.E. [Centro de Investigación en Materiales Avanzados S.C, Alianza norte 202, Parque de Investigación e Innovación Tecnológica, C.P. 66600 Apodaca Nuevo León, México (Mexico); and others

    2014-12-15

    Graphical abstract: - Highlights: • Decolorization of Orange G dye using highly c-axis-oriented ZnO thin films. • The flake-shaped film shows superior and stable photoactivity at a wide range of pH. • The highest photodecolorization was achieved at pH of 7. • The exposure of (101) and (100) facets enhanced the photoactivity. • ZnO thin films exhibit a promising performance as recyclable photocatalysts. - Abstract: The photocatalytic activity of ZnO thin films with different physicochemical characteristics deposited by RF magnetron sputtering on glass substrate was tested for the decolorization of orange G dye aqueous solution (OG). The crystalline phase, surface morphology, surface roughness and the optical properties of these ZnO films were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), atomic force microscopy (AFM) and UV–visible spectroscopy (UV–Vis), respectively. The dye photodecolorization process was studied at acid, neutral and basic pH media under UV irradiation of 365 nm. Results showed that ZnO films grow with an orientation along the c-axis of the substrate and exhibit a wurtzite crystal structure with a (002) preferential crystalline orientation. A clear relationship between surface morphology and photocatalytic activity was observed for ZnO films. Additionally, the recycling photocatalytic abilities of the films were also evaluated. A promising photocatalytic performance has been found with a very low variation of the decolorization degree after five consecutive cycles at a wide range of pH media.

  10. A graphical technique for distinguishing plant material and soil from atmospheric deposition in biomonitors

    International Nuclear Information System (INIS)

    Rahn, K.A.

    2000-01-01

    The paper explores the limits to which a new graphical technique can distinguish the various hierarchical levels of sources of trace elements within biomonitors. When applied to data from Portuguese lichens, it appears to resolve four levels of sources, from plant material down to individual types of pollution. Careful factor analysis appears to offer very similar results, being weaker than the graphical method in some aspects and stronger in others. As a result, it now seems possible to determine sources for elements in lichens with better precision and confidence than was available previously. (author)

  11. Deposition of gold nanoparticle films using spray pyrolysis technique: Tunability of SPR band by electric field

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Neetesh; Komarala, Vamsi K.; Dutta, Viresh [Photovoltaic Laboratory, Centre for Energy Studies, Indian Institute of Technology Delhi, Hauz Khas, New Delhi-110016 (India)

    2012-10-15

    Gold nanoparticle films are prepared using a simple inexpensive spray pyrolysis technique. X-ray as well as TEM diffraction patterns revealed pure cubic structure. The effect of gold nanoparticle concentration on surface plasmon resonance (SPR) band position and bandwidth are investigated for varying spray solution volume. The tunability of SPR band position and bandwidth using an electric field, by applying a voltage (up to 2000 V) to the nozzle, has been demonstrated. The reduced full width at half maximum and blue shift in the SPR band position are observed with {Delta}{lambda}{sub FW} {proportional_to} 55 nm and {Delta}{lambda}{sub P} {proportional_to} 40 nm for the applied voltage of 2 kV. (copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  12. Nanoporous Ti-metal film deposition using radio frequency magnetron sputtering technique for photovoltaic application.

    Science.gov (United States)

    Sung, Youl-Moon; Paeng, Sung-Hwan; Moon, Byung-Ho; Kwak, Dong-Joo

    2012-02-01

    Nanoporous Ti-metal film electrode was fabricated by radio frequency (rf) magnetron sputtering technique on nanoporous TiO2 layer prepared by sol-gel combustion method and investigated with respect to its photo-anode properties of TCO-less DSCs. The porous Ti layer (approximately 1 microm) with low sheet resistance (approximately 17 Omega/sq.) can collect electrons from the TiO2 layer and allows the ionic diffusion of I(-)/I(3-) through the hole. The porous Ti layer with highly ordered columnar structure prepared by 8 mTorr sputtering shows the good impedance characteristics. The efficiency of prepared TCO-less DSCs sample is about 4.83% (ff: 0.6, Voc: 0.65 V, Jsc: 11.2 mA/cm2).

  13. 3D printing of high-resolution PLA-based structures by hybrid electrohydrodynamic and fused deposition modeling techniques

    International Nuclear Information System (INIS)

    Zhang, Bin; Seong, Baekhoon; Byun, Doyoung; Nguyen, VuDat

    2016-01-01

    Recently, the three-dimensional (3D) printing technique has received much attention for shape forming and manufacturing. The fused deposition modeling (FDM) printer is one of the various 3D printers available and has become widely used due to its simplicity, low-cost, and easy operation. However, the FDM technique has a limitation whereby its patterning resolution is too low at around 200 μm. In this paper, we first present a hybrid mechanism of electrohydrodynamic jet printing with the FDM technique, which we name E-FDM. We then develop a novel high-resolution 3D printer based on the E-FDM process. To determine the optimal condition for structuring, we also investigated the effect of several printing parameters, such as temperature, applied voltage, working height, printing speed, flow-rate, and acceleration on the patterning results. This method was capable of fabricating both high resolution 2D and 3D structures with the use of polylactic acid (PLA). PLA has been used to fabricate scaffold structures for tissue engineering, which has different hierarchical structure sizes. The fabrication speed was up to 40 mm/s and the pattern resolution could be improved to 10 μm. (paper)

  14. Novel Optical Diagnostic Techniques for Studying Particle Contact and Deposition Upon a Large Cylinder in a Sheared Suspension

    Science.gov (United States)

    Rashidnia, Nasser (Technical Monitor); Yoda, Minami

    2004-01-01

    The objectives of this research project were: 1) To study the fluid dynamics of sheared particle-liquid suspensions and the impact of differential particle-fluid inertia; 2) To develop new techniques for observing suspension particle contact and deposition upon solid surfaces. Dr. Yoda was supported by the NASA Office of Biological and Physical Research on a four-year grant from March 2000 through November 2004 for a ground-based study on the fluid dynamics of sheared particle-liquid suspensions and the impact of differential particle-fluid inertia on such flows. Such inertial effects can only be observed in reduced-gravity environments since they are overwhelmed by buoyancy effects on Earth. Moreover, these inertial effects will have a significant impact upon suspension flows in microgravity. Suspension dynamics are of importance in a wide variety of advanced life systems applications, including water reclamation and dust mitigation in confined habitats.

  15. Improvement of the inlet system for the spray-jet technique for use in spectroscopic studies and molecular deposition

    International Nuclear Information System (INIS)

    Yamada, Toshiki; Shinohara, Hidenori; Mashiko, Shinro

    2006-01-01

    We previously developed a molecular beam apparatus with a spray-jet technique in order to produce a molecular beam of non-volatile molecules in vacuum from the sprayed mist of a sample solution. The apparatus is for use in spectroscopic studies or a means of molecular deposition. The spray-jet inlet system consisted of an ultrasonic nebulizer, an inlet chamber and a pulsed nozzle. In the present paper, further improvements to the spray-jet inlet system are reported. The main improvement is the introduction of a pneumatic nebulizer to replace the previous ultrasonic nebulizer. The efficiency of molecular beam generation was evaluated on the basis of the signal intensity of the resonantly enhanced multiphoton ionization time-of-flight mass (REMPI-TOFMS) spectra for a Rhodamine B/methanol solution and the amount of sample consumed. The introduction of the pneumatic nebulizer increased the efficiency by a factor of 20

  16. Annealing effects on the structural and optical properties of vanadium oxide film obtained by the hot-filament metal oxide deposition technique (HFMOD)

    Energy Technology Data Exchange (ETDEWEB)

    Scarminio, Jair; Silva, Paulo Rogerio Catarini da, E-mail: scarmini@uel.br, E-mail: prcsilva@uel.br [Universidade Estadual de Londrina (UEL), PR (Brazil). Departamento de Fisica; Gelamo, Rogerio Valentim, E-mail: rogelamo@gmail.com [Universidade Federal do Triangulo Mineiro (UFTM), Uberaba, MG (Brazil); Moraes, Mario Antonio Bica de, E-mail: bmoraes@mailhost.ifi.unicamp.br [Universidade Estadual de Campinas (UNICAMP), SP (Brazil)

    2017-01-15

    Vanadium oxide films amorphous, nonstoichiometric and highly absorbing in the optical region were deposited on ITO-coated glass and on silicon substrates, by the hot-filament metal oxide deposition technique (HFMOD) and oxidized by ex-situ annealing in a furnace at 200, 300, 400 and 500 deg C, under an atmosphere of argon and rarefied oxygen. X-ray diffraction, Raman and Rutherford backscattering spectroscopy as well as optical transmission were employed to characterize the amorphous and annealed films. When annealed at 200 and 300 deg C the as-deposited opaque films become transparent but still amorphous. Under treatments at 400 and 500 deg C a crystalline nonstoichiometric V{sub 2}O{sub 5} structure is formed. All the annealed films became semiconducting, with their optical absorption coefficients changing with the annealing temperature. An optical gap of 2.25 eV was measured for the films annealed at 400 and 500 deg C. The annealing in rarefied oxygen atmosphere proved to be a useful and simple ex-situ method to modulate the structural and optical properties of vanadium oxide films deposited by HFMOD technique. This technique could be applied to other amorphous and non-absorbing oxide films, replacing the conventional and sometimes expensive method of modulate desirable film properties by controlling the film deposition parameters. Even more, the HFMOD technique can be an inexpensive alternative to deposit metal oxide films. (author)

  17. Thermoluminescence properties of undoped diamond films deposited using HF CVD technique

    Directory of Open Access Journals (Sweden)

    Paprocki K.

    2018-03-01

    Full Text Available Natural diamond has been considered as a perspective material for clinical radiation dosimetry due to its tissuebiocompatibility and chemical inertness. However, the use of natural diamond in radiation dosimetry has been halted by the high market price. The recent progress in the development of CVD techniques for diamond synthesis, offering the capability of growing high quality diamond layers, has renewed the interest in using this material in radiation dosimeters having small geometricalsizes. Polycrystalline CVD diamond films have been proposed as detectors and dosimeters of β and α radiation with prospective applications in high-energy photon dosimetry. In this work, we present a study on the TL properties of undoped diamond film samples grown by the hot filament CVD (HF CVD method and exposed to β and α radiation. The glow curves for both types of radiation show similar character and can be decomposed into three components. The dominant TL peaks are centered at around 610 K and exhibit activation energy of the order of 0.90 eV.

  18. Raman Spectroscopy of Solid Oxide Fuel Cells: Technique Overview and Application to Carbon Deposition Analysis

    KAUST Repository

    Maher, R. C.

    2013-07-30

    Raman spectroscopy is a powerful characterization tool for improving the understanding of solid oxide fuel cells (SOFCs), capable of providing direct, molecularly specific information regarding the physical and chemical processes occurring within functional SOFCs in real time. In this paper we give a summary of the technique itself and highlight ex situ and in situ studies that are particularly relevant for SOFCs. This is followed by a case study of carbon formation on SOFC Ni-based anodes exposed to carbon monoxide (CO) using both ex situ and in situ Raman spectroscopy combined with computational simulations. In situ measurements clearly show that carbon formation is significantly reduced for polarized SOFCs compared to those held at open circuit potential (OCP). Ex situ Raman mapping of the surfaces showed clear variations in the rate of carbon formation across the surface of polarized anodes. Computational simulations describing the geometry of the cell showed that this is due to variations in gas access. These results demonstrate the ability of Raman spectroscopy in combination with traditional characterization tools, to provide detailed understanding of critical processes occurring within functional SOFCs. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. Geophysical techniques for exploration of concealed uranium deposits in the Gwalior basin

    International Nuclear Information System (INIS)

    Choudhary, Kalpan; Singh, R.B.

    2004-01-01

    There is no direct geophysical method for the exploration of concealed uranium ore. Scope of geophysics for this in the Gwalior basin comprises delineating the basement topography, demarcation or zones of intense fracturing intersecting the unconformities and to identify the presence of carbonaceous rocks, specially in the graben-like structures. These geophysical problems have been successfully solved in other places by employing IP, resistivity, SP and gravity techniques for basement mapping, identification of fracture zone/shear zone, delineation of electrical conductors like carbonaceous rocks and sulphides. Three such case histories are presented here that include: a). basement and shear/fracture zone mapping in the Vindhyan basin north of Son-Narmada lineament, b). delineation of conductive zone (proved to be carbon phyllite) in the Mahakoshal Group of Kanhara area of Sonbhadra district, UP and c). Identification of a conductive zone, proved to be sulphide body, within the Mahakoshal group in the Gurharpahar area of Sidhi and Sonbhadra districts of MP and UP respectively. In the context of exploration for concealed uranium in the Gwalior basin, it is suggested to employ IP, resistivity, SP, gravity and magnetic methods for delineation of conductive zones like carbonaceous rocks, basement topography, including the graben like structures, fracture zone, geological boundaries and demarcation of the basin boundary. (author)

  20. Experimental setup for producing tungsten coated graphite tiles using plasma enhanced chemical vapor deposition technique for fusion plasma applications

    International Nuclear Information System (INIS)

    Chauhan, Sachin Singh; Sharma, Uttam; Choudhary, K.K.; Sanyasi, A.K.; Ghosh, J.; Sharma, Jayshree

    2013-01-01

    Plasma wall interaction (PWI) in fusion grade machines puts stringent demands on the choice of materials in terms of high heat load handling capabilities and low sputtering yields. Choice of suitable material still remains a challenge and open topic of research for the PWI community. Carbon fibre composites (CFC), Beryllium (Be), and Tungsten (W) are now being considered as first runners for the first wall components of future fusion machines. Tungsten is considered to be one of the suitable materials for the job because of its superior properties than carbon like low physical sputtering yield and high sputter energy threshold, high melting point, fairly high re-crystallization temperature, low fuel retention capabilities, low chemical sputtering with hydrogen and its isotopes and most importantly the reparability with various plasma techniques both ex-situ and in-situ. Plasma assisted chemical vapour deposition is considered among various techniques as the most preferable technique for fabricating tungsten coated graphite tiles to be used as tokamak first wall and target components. These coated tiles are more favourable compared to pure tungsten due to their light weight and easier machining. A system has been designed, fabricated and installed at SVITS, Indore for producing tungsten coated graphite tiles using Plasma Enhanced Chemical Vapor Deposition (PE-CVD) technique for Fusion plasma applications. The system contains a vacuum chamber, a turbo-molecular pump, two electrodes, vacuum gauges, mass analyzer, mass flow controllers and a RF power supply for producing the plasma using hydrogen gas. The graphite tiles will be put on one of the electrodes and WF6 gas will be inserted in a controlled manner in the hydrogen plasma to achieve the tungsten-coating with WF6 dissociation. The system is integrated at SVITS, Indore and a vacuum of the order of 3*10 -6 is achieved and glow discharge plasma has been created to test all the sub-systems. The system design with

  1. pplication of Fractal Technique for Analysis of Geophysical - Geochemical Databases in Tekieh Pb-Zn Ore Deposit (SE of Arak

    Directory of Open Access Journals (Sweden)

    Seyed Reza Mehrnia

    2017-02-01

    Full Text Available Introduction Tekieh Lead-Zinc ore deposit that is located in the Sanandaj-Sirjan structural zone has been recognized as one of the most important mineralized regions in Malayer-Isfahan metallogenic sub-state, south east of Arak (Momenzadeh and Ziseman, 1981. Carbonate host units have been developed along (or across the Vishan-Tekieh anticline as the main structure extended in NW-SE trends (Annells et al, 1985. According to geochemical investigations (Salehi, 2004, the element content of the mineralized regions has originated from Alpine post-volcanisms and subsequently it has migrated toward early Cretaceous formations (dolomitic limestones among several hypogenic stages (Torkashvand et a.2009. Also echelon type structures consisting of folded systems and inversed faulting of structures are the most common features in western and eastern parts of ore deposit regions (Annells et al, 1985. Syngenetic enrichments beside limited (rarely developed epigenetic mineralization have been known as two main phases which are closely relevant to ore forming processes in the massive lenses and vein type occurrences, respectively (Momenzadeh and Ziseman, 1981. Material and Methods In this research, two statistical techniques that consist of classical and fractal equations (Mandelbrot, 2005 were applied in geochemical (Torkashvand et al., 2009 and geophysical (Jafari, 2007 databases for obtaining the linear and nonlinear distributions of geochemical elements (Tekieh Pb-Zn content in association with resistivity variations and induction polarization measurements (Calagari, 2010. According to linear statistical techniques (Torkashvand et al., 2009, the main central parameters such as mean, median and mode in addition to variances and standard deviations as distribution tendencies could be used for obtaining the regression coefficients of the databases. However, in fractal statistics, a reliable regression between geoelectrical - geochemical anomalies should be

  2. Surface morphological properties of CdxZn(1-x)S thin films deposited by low-cost atmospheric pressure metal organic chemical vapour deposition technique (AP-MOCVD)

    Science.gov (United States)

    Kamaruddin, Nurhafiza; Yusoff, Yulisa; Hossain, Towhid; Amin, Nowshad; Akhtaruzzaman, Md.

    2017-11-01

    The CdxZn(1-x)S films have been deposited by low cost atmospheric pressure metal organic chemical vapour deposition (AP-MOCVD) technique and the resulting morphological properties were successfully evaluated for solar cell applications. All morphological properties presented here were investigated by Field-Emission Scanning Microscopy (FESEM) and Energy Dispersive X-Ray (EDX) spectroscopy. It has been observed that the film thickness and grain size have been greatly influenced by the molar ratio of cadmium and zinc, deposition temperature and time. The average grain size of Cd0.5Zn0.5S films (98.16 nm thick) was obtained with deposition temperature and time of 440°C and 2.5 minutes, respectively.

  3. Photoluminescence of nc-Si:Er thin films obtained by physical and chemical vapour deposition techniques: The effects of microstructure and chemical composition

    Energy Technology Data Exchange (ETDEWEB)

    Cerqueira, M.F., E-mail: fcerqueira@fisica.uminho.p [Departamento de Fisica, Universidade do Minho, Campus de Gualtar 4710-057 Braga (Portugal); Losurdo, M. [Institute of Inorganic Methodologies and of Plasmas, IMIP-CNR, Via Orabona n.4-70126 Bari (Italy); Stepikhova, M. [Institute for Physics of Microstructures RAS, 603600 Nizhnij Novgorod GSP-105 (Russian Federation); Alpuim, P.; Andres, G. [Departamento de Fisica, Universidade do Minho, Campus de Gualtar 4710-057 Braga (Portugal); Kozanecki, A. [Polish Academy of Sciences, Institute of Physics, PL-02668, Warsaw (Poland); Soares, M.J.; Peres, M. [Departamento de Fisica, Universidade de Aveiro, Campus de Santiago, 3700 Aveiro (Portugal)

    2009-08-31

    Erbium doped nanocrystalline silicon (nc-Si:Er) thin films were produced by reactive magnetron rf sputtering and by Er ion implantation into chemical vapor deposited Si films. The structure and chemical composition of films obtained by the two approaches were studied by micro-Raman scattering, spectroscopic ellipsometry and Rutherford backscattering techniques. Variation of deposition parameters was used to deposit films with different crystalline fraction and crystallite size. Photoluminescence measurements revealed a correlation between film microstructure and the Er{sup 3+} photoluminescence efficiency.

  4. Study of Sb/SnO2 bi-layer films prepared by ion beam sputtering deposition technique

    International Nuclear Information System (INIS)

    Wang, Chun-Min; Huang, Chun-Chieh; Kuo, Jui-Chao; Huang, Jow-Lay

    2014-01-01

    In the present work, bi-layer thin films of Sb/SnO 2 were produced on unheated glass substrates using ion beam sputtering (IBS) technique without post annealing treatment. The thickness of Sb layers was varied from 2 to 10 nm and the Sb layers were deposited on SnO 2 layers having thicknesses of 40 nm to 115 nm. The effect of thickness was studied on the morphological, electrical and optical properties. The Sb/SnO 2 bi-layer resulted in lowering the electrical resistivity as well as reducing the optical transmittance. However, the optical and electrical properties of the bi-layer films were mainly influenced by the thickness of Sb layers due to progressive transfer in structures from aggregate to continuous films. The bi-layer films show the electrical resistivity of 1.4 × 10 −3 Ω cm and an optical transmittance of 26% for Sb film having 10 nm thickness. - Highlights: • Bi-layer Sb/SnO 2 structures were synthesized by ion beam sputtering (IBS) technique. • The 6 nm-thick Sb film is a transition region in this study. • The conductivity of the bi-layer films is increased as Sb thickness increases. • The transmittance of the bi-layer films is decreased as Sb thickness increases

  5. Characterization of an array of Love-wave gas sensors developed using electrospinning technique to deposit nanofibers as sensitive layers.

    Science.gov (United States)

    Matatagui, D; Fernández, M J; Fontecha, J; Sayago, I; Gràcia, I; Cané, C; Horrillo, M C; Santos, J P

    2014-03-01

    The electrospinning technique has allowed that very different materials are deposited as sensitive layers on Love-wave devices forming a low cost and successful sensor array. Their excellent sensitivity, good linearity and short response time are reported in this paper. Several materials have been used to produce the nanofibers: polymers as Polyvinyl alcohol (PVA), Polyvinylpyrrolidone (PVP) and Polystirene (PS); composites with polymers as PVA+SnCl4; combined polymers as PS+Poly(styrene-alt-maleic anhydride) (PS+PSMA) and metal oxides (SnO2). In order to test the array, well-known chemical warfare agent simulants (CWAs) have been chosen among the volatile organic compounds due to their importance in the security field. Very low concentrations of these compounds have been detected by the array, such as 0.2 ppm of DMMP, a simulant of sarin nerve gas, and 1 ppm of DPGME, a simulant of nitrogen mustard. Additionally, the CWA simulants used in the experiment have been discriminated and classified using pattern recognition techniques, such as principal component analysis and artificial neural networks. Copyright © 2013 Elsevier B.V. All rights reserved.

  6. Mass-spring matching layers for high-frequency ultrasound transducers: a new technique using vacuum deposition.

    Science.gov (United States)

    Brown, Jeremy; Sharma, Srikanta; Leadbetter, Jeff; Cochran, Sandy; Adamson, Rob

    2014-11-01

    We have developed a technique of applying multiple matching layers to high-frequency (>30 MHz) imaging transducers, by using carefully controlled vacuum deposition alone. This technique uses a thin mass-spring matching layer approach that was previously described in a low-frequency (1 to 10 MHz) transducer design with epoxied layers. This mass- spring approach is more suitable to vacuum deposition in highfrequency transducers over the conventional quarter-wavelength resonant cavity approach, because thinner layers and more versatile material selection can be used, the difficulty in precisely lapping quarter-wavelength matching layers is avoided, the layers are less attenuating, and the layers can be applied to a curved surface. Two different 3-mm-diameter 45-MHz planar lithium niobate transducers and one geometrically curved 3-mm lithium niobate transducer were designed and fabricated using this matching layer approach with copper as the mass layer and parylene as the spring layer. The first planar lithium niobate transducer used a single mass-spring matching network, and the second planar lithium niobate transducer used a single mass-spring network to approximate the first layer in a dual quarter-wavelength matching layer system in addition to a conventional quarter-wavelength layer as the second matching layer. The curved lithium niobate transducer was press focused and used a similar mass-spring plus quarter-wavelength matching layer network. These transducers were then compared with identical transducers with no matching layers and the performance improvement was quantified. The bandwidth of the lithium niobate transducer with the single mass-spring layer was measured to be 46% and the insertion loss was measured to be -21.9 dB. The bandwidth and insertion loss of the lithium niobate transducer with the mass-spring network plus quarter-wavelength matching were measured to be 59% and -18.2 dB, respectively. These values were compared with the unmatched

  7. Improving optical properties of silicon nitride films to be applied in the middle infrared optics by a combined high-power impulse/unbalanced magnetron sputtering deposition technique.

    Science.gov (United States)

    Liao, Bo-Huei; Hsiao, Chien-Nan

    2014-02-01

    Silicon nitride films are prepared by a combined high-power impulse/unbalanced magnetron sputtering (HIPIMS/UBMS) deposition technique. Different unbalance coefficients and pulse on/off ratios are applied to improve the optical properties of the silicon nitride films. The refractive indices of the Si3N4 films vary from 2.17 to 2.02 in the wavelength ranges of 400-700 nm, and all the extinction coefficients are smaller than 1×10(-4). The Fourier transform infrared spectroscopy and x-ray diffractometry measurements reveal the amorphous structure of the Si3N4 films with extremely low hydrogen content and very low absorption between the near IR and middle IR ranges. Compared to other deposition techniques, Si3N4 films deposited by the combined HIPIMS/UBMS deposition technique possess the highest refractive index, the lowest extinction coefficient, and excellent structural properties. Finally a four-layer coating is deposited on both sides of a silicon substrate. The average transmittance from 3200 to 4800 nm is 99.0%, and the highest transmittance is 99.97% around 4200 nm.

  8. Superconducting Nd1.85Ce0.15CuO4 films grown by the pulsed electron deposition technique

    International Nuclear Information System (INIS)

    Guo, Y.F.; Chen, L.M.; Lei, M.; Guo, X.; Li, P.G.; Tang, W.H.

    2006-01-01

    Nd 1.85 Ce 0.15 CuO 4-δ superconducting thin films were prepared on (1 0 0) SrTiO 3 substrates by pulsed electron deposition technique without reducing atmosphere. Oxygen content is finely controlled by high temperature vacuum annealing, and optimal superconductivity has been obtained. The deposition conditions of the film are discussed in details. Higher deposition temperature and lower gas pressure result in the loss of copper and the appearance of the foreign phase Ce 0.5 Nd 0.5 O 1.75 . High quality Nd 1.85 Ce 0.15 CuO 4-δ epitaxial films are deposited at 840-870 deg. C in the mixed gas with a ratio of O 2 :Ar = 1:3

  9. Optical property of La1-xSrxTiO3+δ coatings deposited by plasma spraying technique

    Science.gov (United States)

    Zhu, Jinpeng; Gao, Lihong; Ma, Zhuang; Liu, Yanbo; Wang, Fuchi

    2015-11-01

    Perovskite La1-xSrxTiO3+δ oxide is used in various industrial applications because of its excellent physical and chemical properties, which beneficially affects the lifetime and performance of electronic and optical devices. This study illustrates the effects of the spray parameters on particles molten state, microstructure, and optical reflectivity from room temperature up to 1000 °C of single-phase La1-xSrxTiO3+δ (x = 0.1) coating deposited by atmospheric plasma spraying technique. The phase structure and surface morphology of the coating were examined using X-ray diffraction and scanning electron microscopy analysis, respectively, whereas the optical property coating was characterized by UV-visible-near infrared spectroscopy. Results show that plasma spray parameters significantly influenced the microstructure and optical performance of the La1-xSrxTiO3+δ coating, and oxygen deficiency during spraying considerably reduced the coating reflectivity. A high-reflectivity coating can be prepared by adopting optimized plasma spraying parameters and subsequent heat treatment.

  10. Structural and magnetic properties of nickel nanowires grown in porous anodic aluminium oxide template by electrochemical deposition technique

    Science.gov (United States)

    Nugraha Pratama, Sendi; Kurniawan, Yudhi; Muhammady, Shibghatullah; Takase, Kouichi; Darma, Yudi

    2018-03-01

    We study the formation of nickel nanowires (Ni NWs) grown in porous anodic aluminium oxide (AAO) template by the electrochemical deposition technique. Here, the initial AAO template was grown by anodization of aluminium substrate in sulphuric acid solution. The cross-section, crystal structure, and magnetic properties of Ni NWs system were characterized by field-emission SEM, XRD, and SQUID. As a result, the highly-ordered Ni NWs are observed with the uniform diameter of 27 nm and the length from 31 to 163 nm. Based on XRD spectra analysis, Ni NWs have the face-centered cubic structure with the lattice parameter of 0.35 nm and average crystallite size of 17.19 nm. From SQUID measurement at room temperature, by maintaining the magnetic field perpendicular to Ni NWs axis, the magnetic hysteresis of Ni NWs system show the strong ferromagnetism with the coercivity and remanence ratio of ∼148 Oe and ∼0.23, respectively. The magnetic properties are also calculated by means of generalized gradient approximation methods. From the calculation result, we show that the ferromagnetism behavior comes from Ni NWs without any contribution from AAO template or the substrate. This study opens the potential application of Ni NWs system for novel functional magnetic devices.

  11. A Comparative Study of Three Different Chemical Vapor Deposition Techniques of Carbon Nanotube Growth on Diamond Films

    Directory of Open Access Journals (Sweden)

    Betty T. Quinton

    2013-01-01

    Full Text Available This paper compares between the methods of growing carbon nanotubes (CNTs on diamond substrates and evaluates the quality of the CNTs and the interfacial strength. One potential application for these materials is a heat sink/spreader for high-power electronic devices. The CNTs and diamond substrates have a significantly higher specific thermal conductivity than traditional heat sink/spreader materials making them good replacement candidates. Only limited research has been performed on these CNT/diamond structures and their suitability of different growth methods. This study investigates three potential chemical vapor deposition (CVD techniques for growing CNTs on diamond: thermal CVD (T-CVD, microwave plasma-enhanced CVD (MPE-CVD, and floating catalyst thermal CVD (FCT-CVD. Scanning electron microscopy (SEM and high-resolution transmission electron microscopy (TEM were used to analyze the morphology and topology of the CNTs. Raman spectroscopy was used to assess the quality of the CNTs by determining the ID/IG peak intensity ratios. Additionally, the CNT/diamond samples were sonicated for qualitative comparisons of the durability of the CNT forests. T-CVD provided the largest diameter tubes, with catalysts residing mainly at the CNT/diamond interface. The MPE-CVD process yielded non uniform defective CNTs, and FCT-CVD resulted in the smallest diameter CNTs with catalyst particles imbedded throughout the length of the nanotubes.

  12. Advancements in artificial heart valve disks using nano-sized thin films deposited by CVD and sol-gel techniques

    International Nuclear Information System (INIS)

    Kousar, Y.; Ali, N.; Neto, V.F.; Mei, S.; Gracio, J.

    2003-01-01

    Pyrolytic carbon (PyC) is widely used in manufacturing commercial artificial heart valve disks (HVD). Although, PyC is commonly used in HVD, it is not the best material for this application since its blood compatibility is not ideal for prolonged clinical use. As a result thrombosis often occurs and the patients are required to take anti- coagulation drugs on a regular basis in order to minimise the formation of thrombosis. However, the anti-coagulation therapy gives rise to some detrimental side effects in patients. Therefore, it is extremely urgent that newer and more technically advanced materials with better surface and bulk properties are developed. In this paper, we report the mechanical properties of PyC-HVD, namely, strength, wear resistance and coefficient of friction. The strength of the material was assessed using Brinell indentation tests. Furthermore, wear resistance and the coefficient of friction values were obtained from the pin-on-disk testing. The micro-structural properties of PyC were characterized using XRD, Raman spectroscopy and SEM analysis. Also, in this paper we report the preparation of free standing nanocrystalline diamond films (FSND) using the time-modulated chemical vapor deposition (TMCVD) process. Furthermore, the sol-gel technique was used to uniformly coat PyC-HVD with dense, nanocrystalline-titanium oxide (nc-TiO/sub 2/) coatings. The as-grown nc-TiO/sub 2/ coatings were characterized for microstructure using SEM and XRD analysis. (author)

  13. Preparation of SrIrO{sub 3} thin films by using metal-organic aerosol deposition technique

    Energy Technology Data Exchange (ETDEWEB)

    Esser, Sebastian; Schneider, Melanie; Moshnyaga, Vasily; Gegenwart, Philipp [1. Physikalisches Institut, Georg-August-Universitaet Goettingen (Germany)

    2013-07-01

    The interplay between spin-orbit coupling and electronic correlations could lead to interesting novel states in iridium oxide materials. We focus on the perovskite phase of SrIrO{sub 3} because Moon et al. [1] showed by using optical spectroscopy and first-principles calculations that the last member of the Ruddlesden-Popper series Sr{sub n+1}Ir{sub n}O{sub 3n+1} (n = ∞) is close to the Mott transition. By using metal-organic aerosol deposition technique we have grown SrIrO{sub 3} thin films on (111)-oriented SrTiO{sub 3} substrates. The cubic symmetry of the SrTiO{sub 3} substrate ensured that the SrIrO{sub 3} thin film grew in the monoclinic perovskite phase. The X-ray diffraction results suggest that SrIrO{sub 3} thin films in perovskite structure were obtained and these show out of plane epitaxy with monoclinic (002){sub m}-orientation. The temperature dependence of the electrical resistivity of these SrIrO{sub 3} thin films were investigated and metallic behavior was observed down to 50 K.

  14. Comparative study of layer-by-layer deposition techniques for poly(sodium phosphate) and poly(allylamine hydrochloride).

    Science.gov (United States)

    Elosua, Cesar; Lopez-Torres, Diego; Hernaez, Miguel; Matias, Ignacio R; Arregui, Francisco J

    2013-12-20

    An inorganic short chain polymer, poly(sodium phosphate), PSP, together with poly(allylamine hydrochloride), PAH, is used to fabricate layer-by-layer (LbL) films. The thickness, roughness, contact angle, and optical transmittance of these films are studied depending on three parameters: the precursor solution concentrations (10-3 and 10-4 M), the number of bilayers deposited (20, 40, 60, 80, and 100 bilayers), and the specific technique used for the LbL fabrication (dipping or spraying). In most cases of this experimental study, the roughness of the nanofilms increases with the number of bilayers. This contradicts the basic observations made in standard LbL assemblies where the roughness decreases for thicker coatings. In fact, a wide range of thickness and roughness was achieved by means of adjusting the three parameters mentioned above. For instance, a roughness of 1.23 or 205 nm root mean square was measured for 100 bilayer coatings. Contact angles close to 0 were observed. Moreover, high optical transmittance is also reported, above 90%, for 80 bilayer films fabricated with the 10-4 M solutions. Therefore, these multilayer structures can be used to obtain transparent superhydrophilic surfaces.

  15. Growth of InAs Quantum Dots on Germanium Substrate Using Metal Organic Chemical Vapor Deposition Technique

    Directory of Open Access Journals (Sweden)

    Tyagi Renu

    2009-01-01

    Full Text Available Abstract Self-assembled InAs quantum dots (QDs were grown on germanium substrates by metal organic chemical vapor deposition technique. Effects of growth temperature and InAs coverage on the size, density, and height of quantum dots were investigated. Growth temperature was varied from 400 to 450 °C and InAs coverage was varied between 1.40 and 2.35 monolayers (MLs. The surface morphology and structural characteristics of the quantum dots analyzed by atomic force microscope revealed that the density of the InAs quantum dots first increased and then decreased with the amount of InAs coverage; whereas density decreased with increase in growth temperature. It was observed that the size and height of InAs quantum dots increased with increase in both temperature and InAs coverage. The density of QDs was effectively controlled by growth temperature and InAs coverage on GaAs buffer layer.

  16. Theoretical and experimental study of a calorimetric technique for measuring energy deposition in materials caused by complex pile irradiation

    International Nuclear Information System (INIS)

    Mas, P.; Sciers, P.; Droulers, Y.

    1962-01-01

    Calorimetric methods may be used to measure gamma fluxes greater than 10 6 r/h near the cores of swimming pool reactors. The theory, design, and properties of isothermal calorimeters are discussed, and experimental results obtained with two types are presented. Measurement of energy deposition in materials and the long term integration of energy depositions are other uses of these devices. Results of measurements on heat deposition in steel and water are given. Fluxes were also measured. (authors) [fr

  17. Plasma study and deposition of DLC/TiC/Ti multilayer structures using technique combining pulsed laser deposition and magnetron sputtering

    Czech Academy of Sciences Publication Activity Database

    Bulíř, Jiří; Novotný, Michal; Jelínek, Miroslav; Kocourek, Tomáš; Studnička, Václav

    2005-01-01

    Roč. 200, - (2005), s. 708-711 ISSN 0257-8972 R&D Projects: GA AV ČR(CZ) IAA1010110; GA ČR(CZ) GP106/02/P015; GA MŠk(CZ) LN00A015 Institutional research plan: CEZ:AV0Z10100522 Keywords : pulsed laser deposition * magnetron * optical emission spectroscopy * x-ray diffraction * nanostructure Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 1.646, year: 2005

  18. Nanocauliflower like structure of CdS thin film for solar cell photovoltaic applications: Insitu tin doping by chemical bath deposition technique

    CSIR Research Space (South Africa)

    Wilson, KC

    2014-01-01

    Full Text Available We report on surface morphology changes of in situ tin (Sn) doped cadmium sulphide (CdS) thin film nanostructures prepared on a glass substrate using the chemical bath deposition (CBD) technique. Sn-doping in the presence of triethanolammine (TEOA...

  19. Development and application of a green-chemistry solution deposition technique for buffer layer coating on cube-textured metal substrates in view of further deposition of rare-earth based superconductors

    DEFF Research Database (Denmark)

    Pallewatta, Pallewatta G A P

    which consist of YBCO superconducting coatings on cube-textured Ni based alloy tapes.  Before the epitaxial deposition this superconducting layer, a buffer layer is applied on the metal substrate as a diffusion barrier which is also required to transfer the strong texture of the underlying substrate......, allowing the epitaxial growth of the superconducting layer. State-of-the-art coated conductor hetero structures are mainly based on CeO2 based buffer stacks that consist of a sequence of several different buffer layers. Buffer layers deposited by continuous chemical deposition techniques, which...... are the most suitable for large scale production, use to suffer from porosity and cracks that lead to material diffusion from the metal substrate into the superconductor as well as oxidation of the metal during high-temperature processing of the buffer layer. SrTiO3 buffer layers have attracted interest due...

  20. Performance of Erbium-doped TiO2 thin film grown by physical vapor deposition technique

    Science.gov (United States)

    Lahiri, Rini; Ghosh, Anupam; Dwivedi, Shyam Murli Manohar Dhar; Chakrabartty, Shubhro; Chinnamuthu, P.; Mondal, Aniruddha

    2017-09-01

    Undoped and Erbium-doped TiO2 thin films (Er:TiO2 TFs) were fabricated on the n-type Si substrate using physical vapour deposition technique. Field emission scanning electron microscope showed the morphological change in the structure of Er:TiO2 TF as compared to undoped sample. Energy dispersive X-ray spectroscopy (EDX) confirmed the Er doping in the TiO2 thin film (TF). The XRD and Raman spectrum showed the presence of anatase phase TiO2 and Er2O3 in the Er:TiO2 TF. The Raman scattering depicted additional number of vibrational modes for Er:TiO2 TF due to the presence of Er as compared to the undoped TiO2 TF. The UV-Vis absorption measurement showed that Er:TiO2 TF had approximately 1.2 times more absorption over the undoped TiO2 TF in the range of 300-400 nm. The main band transition, i.e., the transition between the oxygen (2p) state and the Ti (3d) state was obtained at 3.0 eV for undoped TiO2 and at 3.2 eV for Er:TiO2 TF, respectively. The photo responsivity measurement was done on both the detectors, where Er:TiO2 TF detector showed better detectivity ( D *), noise equivalent power and temporal response as compared to undoped detector under ultra-violet illumination.

  1. Conformal, planarizing and bridging AZ5214-E layers deposited by a 'draping' technique on non-planar III V substrates

    Science.gov (United States)

    Eliás, P.; Strichovanec, P.; Kostic, I.; Novák, J.

    2006-12-01

    A draping technique was tested for the deposition of positive-tone AZ5214-E photo-resist layers on non-planar (1 0 0)-oriented III-V substrates, which had a variety of three-dimensional (3D) topographies micromachined in them that consisted, e.g., of mesa ridges confined to side facets with variable tilt, inverted pyramidal holes and stubs confined to perpendicular side facets. All objects were sharp-edged. In each draping experiment, an AZ5214-E sheet was (1) formed floating on the water surface, (2) lowered onto a non-planar substrate and (3) draped over it during drying to form either self-sustained, or conformal, or planarizing layers over the non-planar substrates. The draping process is based on the depression of the glass transition temperature Tg of AZ5214-E material induced by penetrant water molecules that interact with AZ5214-E. During the process, the molecules are initially trapped under an AZ5214-E sheet and then transported out through the sheet via permeation. The water-AZ5214-E interaction modifies the stiffness κ of the sheet. The magnitude of the effect depends on temperature T and on partial water vapour pressure difference p(T, P, κ): the net effect is that Tg = f(C(T, P), p(T, P, κ)) is lowered as the concentration C of water increases with T and p, where P is the permeability of the sheet. The interaction depressed the Tg of the sheets as low as or lower than 53 °C for 6 µm thick sheets. At room temperature T Tg, the sheet becomes rubbery and mouldable by adhesion and capillary forces. As a result, it can either contour or planarize the topography depending on its geometry and thickness of the sheet.

  2. Effects of pH and temperature on the deposition properties of stannate chemical conversion coatings formed by the potentiostatic technique on AZ91 D magnesium alloy

    International Nuclear Information System (INIS)

    Elsentriecy, Hassan H.; Azumi, Kazuhisa; Konno, Hidetaka

    2008-01-01

    The effects of pH and temperature of a stannate bath on the quality of stannate chemical conversion coatings formed on AZ91 D magnesium alloy by using the potentiostatic polarization technique at E = -1.1 V were investigated in order to improve uniformity and corrosion protection performance of the coating films. It was found that the uniformity and corrosion resistance of coating films deposited by potentiostatic polarization were closely associated with pH and temperature of the coating bath. The pH and temperature to obtain the best coating film were investigated as a function of corrosion protection performance evaluated by curves of potentiodynamic anodic polarization conducted in borate buffer solution. Scanning electron microscope observation and electrochemical corrosion tests of the stannate-coated samples confirmed significant improvement in uniformity and corrosion resistivity of coating films deposited by the potentiostatic technique by modifying the pH and temperature of the coating bath. It was also found that uniformity and corrosion resistivity of the coating films deposited by the potentiostatic technique were considerably improved compared to those of coatings deposited by the simple immersion method at the best conditions of pH and temperature of the coating bath

  3. Iron deposition in cranial bone marrow with sickle cell disease: MR assessment using a fat suppression technique

    Energy Technology Data Exchange (ETDEWEB)

    Kaneko, K. (Dept. of Radiology, Tulane Univ. Medical Center, New Orleans, LA (United States)); Humbert, J.H. (Dept. of Pediatrics, Tulane Univ. Medical Center, New Orleans, LA (United States)); Kogutt, M.S. (Dept. of Radiology, Tulane Univ. Medical Center, New Orleans, LA (United States)); Robinson, A.E. (Dept. of Radiology, Tulane Univ. Medical Center, New Orleans, LA (United States))

    1993-10-01

    Thirteen patients with sickle cell disease (SCD) undergoing transfusion therapy and 8 control patients were examined by magnetic resonance imaging to discriminate bone marrow change due to iron deposition from hematologic marrow hyperplasia. Using T1-weighted spin echo images, only two subjects showed extremely low signal intensity marrow compatible with iron deposition. However, using T2-weighted fast spin echo images with fat suppression, cranial bone marrow in SCD patients with transfusion therapy showed considerably lower signal than that of controls. The main cause of marrow signal decrease in SCD patients with transfusion therapy was considered to be iron deposition due to repeated transfusion therapy rather than red marrow hyperplasia. (orig.)

  4. In situ structural study on underpotential deposition of Ag on Au(111) electrode using surface X-ray scattering technique

    OpenAIRE

    Kondo, Toshihiro; Morita, Jun; Okamura, Masayuki; Saito, Toshiya; Uosaki, Kohei

    2002-01-01

    In situ surface X-ray scattering (SXS) measurements were carried out to study the structure of a Ag layer on a Au(111) electrode formed by underpotential deposition (upd) in sulfuric acid solution. Specular rod profiles showed that a monolayer of Ag was formed at a potential between the second and third upd peaks, and a bilayer of Ag was formed at a potential between the third upd peak and bulk deposition. Non-specular rod profiles demonstrated that electrochemically deposited Ag atoms both i...

  5. Iron deposition in cranial bone marrow with sickle cell disease: MR assessment using a fat suppression technique

    International Nuclear Information System (INIS)

    Kaneko, K.; Humbert, J.H.; Kogutt, M.S.; Robinson, A.E.

    1993-01-01

    Thirteen patients with sickle cell disease (SCD) undergoing transfusion therapy and 8 control patients were examined by magnetic resonance imaging to discriminate bone marrow change due to iron deposition from hematologic marrow hyperplasia. Using T1-weighted spin echo images, only two subjects showed extremely low signal intensity marrow compatible with iron deposition. However, using T2-weighted fast spin echo images with fat suppression, cranial bone marrow in SCD patients with transfusion therapy showed considerably lower signal than that of controls. The main cause of marrow signal decrease in SCD patients with transfusion therapy was considered to be iron deposition due to repeated transfusion therapy rather than red marrow hyperplasia. (orig.)

  6. Source investigation of the tar balls deposited along the Gujarat coast, India, using chemical fingerprinting and transport modeling techniques

    Digital Repository Service at National Institute of Oceanography (India)

    Suneel, V.; Vethamony, P.; Naik, B.G.; VinodKumar, K.; Sreenu, L.; Samiksha, S.V.; Tai,Y.; Sudheesh, K.

    Deposition of tar balls (TBs) along the south Gujarat coast, situated on the west coast of India (WCI), commonly occurs during the southwest monsoon season. Several offshore oil fields off the Mumbai-Gujarat coast, and refineries along the coast...

  7. Multi objective optimization of wear resistant TiAlN and TiN coatings deposite by PVD techniques

    OpenAIRE

    A. Zarychta; J. Ratajski; Ł. Szparaga

    2011-01-01

    Purpose: The goal of this paper is to determine, the optimal layer thickness of deposited coatings, in respect of thermal strain and stresses.Design/methodology/approach: For physical modelling purposes Cr, TiN and TiAlN layers were treated as a continuous medium, so the physical phenomena, occurring in the coating, are modelled based on a classical theory of stiffness. Computer model of the object (coating + substrate) describing strains and thermal stresses states in layers, after deposit...

  8. Seismic refraction technique aplications in the geotechnical characterization of the Cachoeira deposit massif, Caetite, State of Bahia, Brazil

    International Nuclear Information System (INIS)

    Malagutti Filho, W.; Oliveira Braga, T. de.

    1984-01-01

    Geophysical surveys throught the Cachoeira Uranium deposit massif were carried out with the purpose of assisting in the geotechnical characterization for the implantation of the Mining-Industrial Complex projects on the Lagoa Real uranium deposits, Caetite municipality, state of Bahia, Brazil. This study discusses the methodology utilized in the geophysical surveys and their results as well as their applications to the geotechnical characterization as a whole. (D.J.M.) [pt

  9. Monte Carlo Techniques for Calculations of Charge Deposition and Displacement Damage from Protons in Visible and Infrared Sensor Arrays

    Science.gov (United States)

    Marshall, Paul; Reed, Robert; Fodness, Bryan; Jordan, Tom; Pickel, Jim; Xapsos, Michael; Burke, Ed

    2004-01-01

    This slide presentation examines motivation for Monte Carlo methods, charge deposition in sensor arrays, displacement damage calculations, and future work. The discussion of charge deposition sensor arrays includes Si active pixel sensor APS arrays and LWIR HgCdTe FPAs. The discussion of displacement damage calculations includes nonionizing energy loss (NIEL), HgCdTe NIEL calculation results including variance, and implications for damage in HgCdTe detector arrays.

  10. Atomic force microscopy and Langmuir-Blodgett monolayer technique to assess contact lens deposits and human meibum extracts.

    Science.gov (United States)

    Hagedorn, Sarah; Drolle, Elizabeth; Lorentz, Holly; Srinivasan, Sruthi; Leonenko, Zoya; Jones, Lyndon

    2015-01-01

    The purpose of this exploratory study was to investigate the differences in meibomian gland secretions, contact lens (CL) lipid extracts, and CL surface topography between participants with and without meibomian gland dysfunction (MGD). Meibum study: Meibum was collected from all participants and studied via Langmuir-Blodgett (LB) deposition with subsequent Atomic Force Microscopy (AFM) visualization and surface roughness analysis. CL Study: Participants with and without MGD wore both etafilcon A and balafilcon A CLs in two different phases. CL lipid deposits were extracted and analyzed using pressure-area isotherms with the LB trough and CL surface topographies and roughness values were visualized using AFM. Meibum study: Non-MGD participant meibum samples showed larger, circular aggregates with lower surface roughness, whereas meibum samples from participants with MGD showed more lipid aggregates, greater size variability and higher surface roughness. CL Study: Worn CLs from participants with MGD had a few large tear film deposits with lower surface roughness, whereas non-MGD participant-worn lenses had many small lens deposits with higher surface roughness. Balafilcon A pore depths were shallower in MGD participant worn lenses when compared to non-MGD participant lenses. Isotherms of CL lipid extracts from MGD and non-MGD participants showed a seamless rise in surface pressure as area decreased; however, extracts from the two different lens materials produced different isotherms. MGD and non-MGD participant-worn CL deposition were found to differ in type, amount, and pattern of lens deposits. Lipids from MGD participants deposited irregularly whereas lipids from non-MGD participants showed more uniformity. Copyright © 2014 Spanish General Council of Optometry. Published by Elsevier Espana. All rights reserved.

  11. Structural and optical studied of nano structured lead sulfide thin films prepared by the chemical bath deposition technique

    Energy Technology Data Exchange (ETDEWEB)

    Al Din, Nasser Saad, E-mail: nsaadaldin@yahoo.com; Hussain, Nabiha, E-mail: nabihahssin@yahoo.com [Damascus University Faculty of Science, Department of physics, Homs (Syrian Arab Republic); Jandow, Nidhal, E-mail: nidhaljandow@yahoo.com [Al –Mustansiriyah University, College of Education, Department of physics, Baghdad (Iraq)

    2016-07-25

    Lead (II) Sulfide PbS thin films were deposited on glass substrates at 25°C by chemical bath deposition (CBD) method. The structural properties of the films were studied as a function of the concentration of Thiourea (CS (NH{sub 2}){sub 2}) as Source of Sulfide and deposition time. The surface morphology of the films was characterized by X-ray diffraction and SEM. The obtained results showed that the as-deposited films Polycrystalline had cubic crystalline phase that belong to S.G: Fm3m. We found that they have preferred orientation [200]. Also the thickness of thin films decrease with deposition time after certain value and, it observed free sulfide had orthorhombic phase. Optical properties showed that the thin films have high transmission at visible range and low transmission at UV, IR range. The films of PbS have direct band gap (I.68 - 2.32 ev) at 300 K the values of band energy decreases with increases thickness of the Lead (II) Sulfide films.

  12. Manipulating microstructures and electrical properties of carbon fiber/reduced graphene oxide/nickel composite textiles with electrochemical deposition techniques

    Science.gov (United States)

    Cheng, Wei-Liang; Zhao, Quan-Liang; Shi, Fei

    2017-04-01

    Since graphene and their composites play significant roles in the catalysts, energy storage, electronics and other fields, where electron transport is highly critical, here, we introduce reduced graphene oxide (RGO) interfaces in the carbon fiber (CF) networks for preparing a novel lightweight carbon fiber/reduced graphene oxide/nickel (CF-RGO-Ni) composite textile. Upon the charaterizations on the microscopic morphologies, electrical and magnetic properties, and density, the presence of RGO nanosheets and nickel nanoparticles would substantially influence the related physical properties in the resulting composite textiles. Furthermore, the key parameters, including RGO loading, deposition time, current density and annealing temperature of carbon matrices, have been studied to understand their effects on the electrochemical deposition of nickel nanoparticles. Implication of the results suggests that the RGO interface is a unique medium for essentially promoting the electrochemical deposition kinetics and active sites for growing nickel nanoparticles, which indicates a universal approach for preparing advanced lightweight composites with the presence of graphene naonstructures.

  13. The Influence of Selected Fingerprint Enhancement Techniques on Forensic DNA Typing of Epithelial Cells Deposited on Porous Surfaces.

    Science.gov (United States)

    Tsai, Li-Chin; Lee, Cheng-Chang; Chen, Chun-Chieh; Lee, James Chun-I; Wang, Sheng-Meng; Huang, Nu-En; Linacre, Adrian; Hsieh, Hsing-Mei

    2016-01-01

    Fingerprints deposited at crime scene can be a source of DNA. Previous reports on the effects of fingerprint enhancement methods have focused mainly on fingermarks deposited in blood or saliva. Here, we evaluate the effects of fingerprint enhancement methods on fingerprints deposited on porous surfaces. We performed real-time quantification and STR typing, the results of which indicated that two methods (iodine fuming and 1,2-indanedione in ethyl acetate enhancement) had no effect on the quantity of DNA isolated and resultant STR alleles when compared to control samples. DNA quantities and allele numbers were lower for samples enhanced with silver nitrate and 1,2-indanedione in acetic acid when compared to control samples. Based on DNA quantity, quality, and observable stochastic effects, our data indicated that iodine fuming and 1,2-indanedione in ethyl acetate were the preferred options for the enhancement of fingerprints on porous surfaces. © 2015 American Academy of Forensic Sciences.

  14. Trace detection of herbicides by SERS technique, using SERS-active substrates fabricated from different silver nanostructures deposited on silicon

    International Nuclear Information System (INIS)

    Dao, Tran Cao; Luong, Truc Quynh Ngan; Nguyen, Ngoc Hai; Kieu, Ngoc Minh; Luong, Thi Thuy; Cao, Tuan Anh; Le, Van Vu

    2015-01-01

    In this report we present the initial results of the use of different silver nanostructures deposited on silicon for trace detection of paraquat (a commonly used herbicide) using the surface-enhanced Raman scattering (SERS) effect. More specifically, the SERS-active substrates were fabricated from silver nanoparticles (AgNPs) deposited onto the flat surface of a silicon wafer (AgNPs@Si substrate), as well as on the surface of an obliquely aligned silicon nanowire (SiNW) array (AgNPs@SiNWs substrate), and from silver nanodendrites (AgNDs) deposited onto the flat surface of a silicon wafer (AgNDs@Si substrate). Results showed that with the change of the structure of the SERS-active substrate, higher levels of SERS enhancement have been achieved. Specifically, with the fabricated AgNDs@Si substrate, paraquat concentration as low as 1 ppm can be detected. (paper)

  15. Physical aspects of the pulsed laser deposition technique: The stoichiometric transfer of material from target to film

    DEFF Research Database (Denmark)

    Schou, Jørgen

    2009-01-01

    The physical processes of pulsed laser deposition (PLD) change strongly from the initial light absorption in a target to the final deposition and growth of a film. One of the primary advantages of PLD is the stoichiometric transfer of material from target to a film on a substrate. Even...... for a stoichiometric flow of material from a multicomponent target, the simultaneous arrival of the target atoms is not sufficient to ensure a stoichiometric film growth. The laser fluence has to be sufficiently high to induce ablation rather than pure evaporation from target, but a high fluence may lead...

  16. Physics of enriched uranyl fluoride deposit characterizations using active neutron and gamma interrogation techniques with 252Cf

    International Nuclear Information System (INIS)

    Wyatt, M.S.; Hannon, T.F.

    1998-01-01

    A method was developed and successfully applied to characterize large uranyl fluoride (UO 2 F 21 ) deposits at the former Oak Ridge Gaseous Diffusion Plant. These deposits were formed by a wet air in-leakage into the UF 6 process gas lines over a period of years. The resulting UO 2 F 2 is hygroscopic, readily absorbing moisture from the air to form hydrates as UO 2 F 2 -nH 2 O. The ratio of hydrogen to uranium, denoted H/U, can vary from 0--16, and has significant nuclear criticality safety impacts for large deposits. In order to properly formulate the required course of action, a non-intrusive characterization of the distribution of the fissile material within the pipe, its total mass, and amount of hydration was needed. The Nuclear Weapons Identification System (NWIS) previously developed at the Oak Ridge Y-12 Plant for identification of uranium weapons components in storage containers was used to successfully characterize the distribution, hydration, and total mass of these deposits

  17. Thiol-modified gold-coated glass as an efficient hydrophobic substrate for drop coating deposition Raman (DCDR) technique

    Czech Academy of Sciences Publication Activity Database

    Kočišová, E.; Procházka, M.; Šípová, Hana

    2016-01-01

    Roč. 47, č. 11 (2016), s. 1394-1396 ISSN 0377-0486 R&D Projects: GA ČR(CZ) GBP205/12/G118 Institutional support: RVO:67985882 Keywords : thiol-modified Au-coated glass * drop coating deposition Raman * liposome Subject RIV: BH - Optics, Masers, Lasers Impact factor: 2.969, year: 2016

  18. Tunable white light emission from hafnium oxide films co-doped with trivalent terbium and europium ions deposited by Pyrosol technique

    Energy Technology Data Exchange (ETDEWEB)

    Guzman-Olguin, J.C.; Montes, E.; Guzman-Mendoza, J. [Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada del Instituto Politecnico Nacional, Unidad Legaria (Mexico); Baez-Rodriguez, A.; Zamora-Peredo, L. [Centro de Investigacion en Micro y Nanotecnologia, Universidad Veracruzana, Boca del Rio, Ver (Mexico); Garcia-Hipolito, M.; Alvarez-Fregoso, O. [Instituto de Investigaciones en Materiales, Universidad Nacional Autonoma de Mexico, Circuito Exterior, Ciudad Universitaria, Coyoacan (Mexico); Martinez-Merlin, I.; Falcony, C. [Centro de Investigacion y de Estudios Avanzados del Instituto Politecnico Nacional (Mexico)

    2017-10-15

    In this paper, the photo and cathodoluminescent properties of HfO{sub 2} films optically activated with different atomic concentrations of Tb{sup 3+} and Eu{sup 3+} ions, deposited by the Pyrosol technique, are reported. These films were deposited at temperatures from 400 to 600 C, using chlorides as raw materials. The surface morphologies of all deposited films were rough and dense. X-ray diffraction analysis showed that the films deposited at 600 C were polycrystalline exhibiting the HfO{sub 2} monoclinic phase. The tuning by the means of the excitation wavelength generates photoluminescence spectra, for co-doped films, in several emissions from blue to yellow (including white light) due to the characteristic electronic transitions of Tb{sup 3+} (green), Eu{sup 3+}(red) ions and the violet-blue emission associated to the host lattice (HfO{sub 2}). According to the chromaticity diagram, the best white light is reached for the sample S2 excited with 382 nm (x = 0.3343, y = 0.3406). The cathodoluminescence emission spectra for co-doped films showed emissions from green to red (including yellow, orange and other intermediate emissions). The averaged quantum efficiency values of the sample labeled as S2 resulted between 47 and 78% depending on the excitation wavelength. In addition, XPS, TEM, SEM and decay times were performed to characterize these films. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  19. pplication of Fractal Technique for Analysis of Geophysical - Geochemical Databases in Tekieh Pb-Zn Ore Deposit (SE of Arak)

    OpenAIRE

    Seyed Reza Mehrnia

    2017-01-01

    Introduction Tekieh Lead-Zinc ore deposit that is located in the Sanandaj-Sirjan structural zone has been recognized as one of the most important mineralized regions in Malayer-Isfahan metallogenic sub-state, south east of Arak (Momenzadeh and Ziseman, 1981). Carbonate host units have been developed along (or across) the Vishan-Tekieh anticline as the main structure extended in NW-SE trends (Annells et al, 1985). According to geochemical investigations (Salehi, 2004), the element content o...

  20. Characterization of luminescent praseodymium-doped ZrO2 coatings deposited by ultrasonic spray pyrolysis technique

    International Nuclear Information System (INIS)

    Ramos-Brito, F; Garcia-Hipolito, M; Alejo-Armenta, C; Alvarez-Fragoso, O; Falcony, C

    2007-01-01

    ZrO 2 : Pr films were synthesized by the ultrasonic spray pyrolysis process. X-ray diffraction studies, as a function of the deposition temperature, indicate a tetragonal crystal structure of zirconia as the substrate temperature was increased. Luminescence (photo- and cathodoluminescence) properties of the films were studied as a function of growth parameters such as the substrate temperature and the praseodymium concentration. For an excitation wavelength of 290 nm, all the photoluminescent emission spectra show peaks located at 490, 510, 566, 615, 642, 695, 718, 740 and 833 nm, associated with the electronic transitions 3 P 0 → 3 H 4 , 3 P 0 → 3 H 4 , 3 P 1 + 1 I 6 → 3 H 5 , 1 D 2 → 3 H 4 , 3 P 0 → 3 H 6 , 1 D 2 → 3 H 5 , 1 D 2 → 3 H 5 , 3 P 0 → 3 F 3,4 and 1 D 2 → 3 F 2 of the Pr 3+ ion. As the deposition temperature is increased, an increasing intensity of the luminescence emission is observed. Also, quenching of the luminescence, with increasing doping concentration, is observed. The chemical composition of the films as determined by energy dispersive spectroscopy is reported as well. In addition, the surface morphology characteristics of the films, as a function of the deposition temperature, are presented

  1. Investigation of chemical vapour deposition diamond detectors by X- ray micro-beam induced current and X-ray micro-beam induced luminescence techniques

    CERN Document Server

    Olivero, P; Vittone, E; Fizzotti, F; Paolini, C; Lo Giudice, A; Barrett, R; Tucoulou, R

    2004-01-01

    Tracking detectors have become an important ingredient in high-energy physics experiments. In order to survive the harsh detection environment of the Large Hadron Collider (LHC), trackers need to have special properties. They must be radiation hard, provide fast collection of charge, be as thin as possible and remove heat from readout electronics. The unique properties of diamond allow it to fulfill these requirements. In this work we present an investigation of the charge transport and luminescence properties of "detector grade" artificial chemical vapour deposition (CVD) diamond devices developed within the CERN RD42 collaboration, performed by means of X-ray micro-beam induced current collection (XBICC) and X-ray micro- beam induced luminescence (XBIL) techniques. XBICC technique allows quantitative estimates of the transport parameters of the material to be evaluated and mapped with micrometric spatial resolution. In particular, the high resolution and sensitivity of the technique has allowed a quantitati...

  2. Relaxed eddy accumulation, a new technique for measuring emission and deposition fluxes of volatile organic compounds by capillary gas chromatography and mass spectrometry.

    Science.gov (United States)

    Ciccioli, P; Brancaleoni, E; Frattoni, M; Marta, S; Brachetti, A; Vitullo, M; Tirone, G; Valentini, R

    2003-01-24

    The possibility afforded by a new relaxed eddy accumulation system in the determination of emission and deposition fluxes of volatile organic compounds (VOCs) by chromatographic techniques will be presented. The system, especially designed to limit sampling artifacts, uses adsorption traps filled with solid sorbents as reservoirs for VOC collection. Enriched compounds were analyzed by capillary GC and positive identification and quantification of eluted compounds was Achieved by mass-spectrometric detection. The method has been used to quantify the emission and deposition of both biogenic and anthropogenic VOCs over a Mediterranean forest ecosystem located in Central Italy. For the first time, both daily and seasonal trends of anthropogenic and biogenic VOCs will be reported. The consistency of monoterpene fluxes with predictions based on the knowledge of VOC emission from the dominant vegetation species will be tested. Data have been used to develop a novel algorithm to predict the seasonality of biogenic emission from the forest ecosystem.

  3. Structural and electronic properties of InN epitaxial layer grown on c-plane sapphire by chemical vapor deposition technique

    Energy Technology Data Exchange (ETDEWEB)

    Barick, Barun Kumar, E-mail: bkbarick@gmail.com; Prasad, Nivedita; Saroj, Rajendra Kumar; Dhar, Subhabrata [Department of Physics, Indian Institute of Technology, Bombay, Mumbai 400076 (India)

    2016-09-15

    Growth of InN epilayers on c-plane sapphire substrate by chemical vapor deposition technique using pure indium metal and ammonia as precursors has been systematically explored. It has been found that [0001] oriented indium nitride epitaxial layers with smooth surface morphology can be grown on c-plane sapphire substrates by optimizing the growth conditions. Bandgap of the film is observed to be Burstein–Moss shifted likely to be due to high background electron concentration. It has been found that the concentration of this unintentional doping decreases with the increase in the growth temperature and the ammonia flux. Epitaxial quality on the other hand deteriorates as the growth temperature increases. Moreover, the morphology of the deposited layer has been found to change from flat top islands to faceted mounds as the flow rate of ammonia increases. This phenomenon is expected to be related to the difference in surface termination character at low and high ammonia flow rates.

  4. Analysis of the characteristics of thick-film NTC thermistor devices manufactured by screen-printing and firing technique and by room temperature aerosol deposition method (ADM)

    Science.gov (United States)

    Schubert, Michaela; Kita, Jaroslaw; Münch, Christian; Moos, Ralf

    The study compares thick-film NTC thermistor devices, produced by the screen-printing (and firing) technique and by the Aerosol Deposition Method (ADM) at room temperature. The devices are compared with respect to film quality (optical, mechanical) and to the negative temperature coefficient of resistance (NTCR) parameters ρ25 and B. While the screen-printed films are porous, the Aerosol Deposited (AD) films are characterized by high tightness, mechanical stability, and a production at room temperature. The electrical analysis shows that the AD films reach the ρ25- and B-values of bulk NTCRs from literature after a moderate tempering step below 400∘C in air. The screen-printed films show B-values that are comparable to the values of bulk NTCRs from literature and ρ25-values that are significantly higher.

  5. Investigations on alluvial deposits through borehole stratigraphy, radiocarbon dating and passive seismic technique (Carnic Alps, NE Italy)

    Science.gov (United States)

    Viero, Alessia; Marchi, Lorenzo; Cavalli, Marco; Crema, Stefano; Fontana, Alessandro; Mozzi, Paolo; Venturini, Corrado

    2016-04-01

    Alluvial sediment investigations provide fundamental tools to infer the processes that control geomorphological evolution of mountain environments. By analyzing sediment stratigraphy in depth, it is possible to retrieve the source, the geology, the time of deposition, the relative distance travelled by material as well as to distinguish among different type of transport (i.e., gravitational, fluvial or glacial). In this work, we present a combination of log stratigraphy, radiocarbon dating and geophysical surveys carried out on the valley floor of the But River (Carnic Alps, North East Italy). The But River basin drains an area of 326 km2 with a range in elevation from 2769 to 323 m a.s.l.; the bedrock mainly consists of carbonates and quartz arenites with minor inclusions of effusive rocks. After Pleistocene the gravitational deposits from mountain slopes have impounded the But River several times. In particular, we analyzed a sector of the upper portion of the But valley close to the confluence of the Moscardo Torrent, frequently affected by debris flows. A borehole was drilled in the But River floodplain, at the intersection with the Moscardo Torrent alluvial fan, down to a depth of 80 m. The analysis of the core samples allowed discerning three sedimentary levels rich in clay and organic materials, which testify the presence of small dam lakes, originated from the Moscardo debris-flow deposits. Three samples of wood and plant debris were collected from 13, 14 and 23 m of depth, respectively. They were analyzed through radiocarbon dating in order to determine the age of the lakes and, thus, to infer the activity of the debris flows building the Moscardo cone. The calibrated ages of the 3 samples are close to the younger limit of the radiocarbon method indicating a fast aggradation of the valley floor, starting from a period ranging between 1450 - 1632 AD. Historical maps and documents confirm the presence of the lakes until 19th century and they permit to assess

  6. Structural, nanomechanical and variable range hopping conduction behavior of nanocrystalline carbon thin films deposited by the ambient environment assisted filtered cathodic jet carbon arc technique

    Energy Technology Data Exchange (ETDEWEB)

    Panwar, O.S., E-mail: ospanwar@mail.nplindia.ernet.in [Polymorphic Carbon Thin Films Group, Physics of Energy Harvesting Division, CSIR-National Physical Laboratory, Dr. K. S. Krishnan Road, New Delhi - 110 012 (India); Rawal, Ishpal; Tripathi, R.K. [Polymorphic Carbon Thin Films Group, Physics of Energy Harvesting Division, CSIR-National Physical Laboratory, Dr. K. S. Krishnan Road, New Delhi - 110 012 (India); Srivastava, A.K. [Electron and Ion Microscopy, Sophisticated and Analytical Instruments, CSIR-National Physical Laboratory, Dr. K. S. Krishnan Road, New Delhi - 110 012 (India); Kumar, Mahesh [Ultrafast Opto-Electronics and Tetrahertz Photonics Group, CSIR-National Physical Laboratory, Dr. K. S. Krishnan Road, New Delhi - 110 012 (India)

    2015-04-15

    Highlights: • Nanocrystalline carbon thin films are grown by filtered cathodic jet carbon arc process. • Effect of gaseous environment on the properties of carbon films has been studied. • The structural and nanomechanical properties of carbon thin films have been studied. • The VRH conduction behavior in nanocrystalline carbon thin films has been studied. - Abstract: This paper reports the deposition and characterization of nanocrystalline carbon thin films by filtered cathodic jet carbon arc technique assisted with three different gaseous environments of helium, nitrogen and hydrogen. All the films are nanocrystalline in nature as observed from the high resolution transmission electron microscopic (HRTEM) measurements, which suggests that the nanocrystallites of size ∼10–50 nm are embedded though out the amorphous matrix. X-ray photoelectron spectroscopic studies suggest that the film deposited under the nitrogen gaseous environment has the highest sp{sup 3}/sp{sup 2} ratio accompanied with the highest hardness of ∼18.34 GPa observed from the nanoindentation technique. The film deposited under the helium gaseous environment has the highest ratio of the area under the Raman D peak to G peak (A{sub D}/A{sub G}) and the highest conductivity (∼2.23 S/cm) at room temperature, whereas, the film deposited under the hydrogen environment has the lowest conductivity value (2.27 × 10{sup −7} S/cm). The temperature dependent dc conduction behavior of all the nanocrystalline carbon thin films has been analyzed in the light of Mott’s variable range hopping (VRH) conduction mechanism and observed that all the films obey three dimension VRH conduction mechanism for the charge transport.

  7. The study and the realization of radiation detectors made from polycrystalline diamond films grown by microwave plasma enhanced chemical vapour deposition technique

    International Nuclear Information System (INIS)

    Jany, Ch.

    1998-01-01

    The aim of this work was to develop radiation detectors made from polycrystalline diamond films grown by microwave plasma enhanced chemical vapour deposition technique. The influence of surface treatments, contact technology and diamond growth parameters on the diamond detectors characteristics was investigated in order to optimise the detector response to alpha particles. The first part of the study focused on the electrical behaviour of as-deposited diamond surface, showing a p type conduction and its influence on the leakage current of the device. A surface preparation process was established in order to reduce the leakage current of the device by surface dehydrogenation using an oxidising step. Several methods to form and treat electrical contacts were also investigated showing that the collection efficiency of the device decreases after contact annealing. In the second part, we reported the influence of the diamond deposition parameters on the characteristics of the detectors. The increase of the deposition temperature and/or methane concentration was shown to lead η to decrease. In contrast, η was found to increase with the micro-wave power. The evolution of the diamond detector characteristics results from the variation in sp 2 phases incorporation and in the crystallography quality of the films. These defects increase the leakage current and reduce the carrier mobility and lifetime. Measurements carried out on detectors with different thicknesses showed that the physical properties varies along the growth direction, improving with the film thickness. Finally, the addition of nitrogen (> 10 ppm) in the gas mixture during diamond deposition was found to strongly reduce the collection efficiency of the detectors. To conclude the study, we fabricated and characterised diamond devices which were used for thermal neutron detection and for the intensity and shape measurement of VUV and soft X-ray pulses. (author)

  8. Characterization of AgGa{sub 0.5}In{sub 0.5}Se{sub 2} thin films deposited by electron-beam technique

    Energy Technology Data Exchange (ETDEWEB)

    Karaagac, H; Parlak, M [Department of Physics, Middle East Technical University, 06531 Ankara (Turkey); Kaleli, M, E-mail: parlak@metu.edu.t [Department of Physics, Sueleyman Demirel University, 32260 Isparta (Turkey)

    2009-08-21

    AgGa{sub 0.5}In{sub 0.5}Se{sub 2} thin films were deposited onto a quartz substrate by the electron-beam technique. For the investigation of the annealing effect on structural, optical and electrical properties of deposited films, samples were annealed in the temperature range 300-775 {sup 0}C. The composition analyses of the deposited films carried out by energy dispersive x-ray analysis measurements have shown that the deposited AgGa{sub 0.5}In{sub 0.5}Se{sub 2} films were indium- and gallium-rich but selenium- and slightly silver-deficient and there was a remarkable change in composition with annealing. As a result of x-ray diffraction measurements, the as-deposited films were found to have an amorphous structure and after annealing at 300 {sup 0}C a polycrystalline structure with different phases was observed. However, subsequent annealing resulted in the formation of single phase AgGa{sub 0.5}In{sub 0.5}Se{sub 2} thin film at about 775 {sup 0}C. The absorption coefficient of the films was determined from the transmission spectra and the band gap values were calculated and found to vary between 1.57 and 2.43 eV following annealing in the temperature range 300-775 {sup 0}C. The refractive index (n) and extinction coefficient (k) of the films were evaluated by applying the envelope method to the transmission spectra. The spectral distributions of these quantities for both as-deposited and annealed films were determined in detail and it was observed that there has been a remarkable influence of annealing on these quantities. The electrical properties of AgGa{sub 0.5}In{sub 0.5}Se{sub 2} thin films were also investigated by means of temperature dependent conductivity measurements in the temperature range 100-460 K. The resistivity of the samples depending on the annealing temperature varied between 6.5 x 10{sup 5} and 16 {Omega} cm. As a result of the hot-probe method it was observed that the as-deposited films have indicated an n-type behaviour, while all the

  9. OPTICAL PROPERTIES OF Al:ZnO THIN FILM DEPOSITED BY DIFFERENT SOL-GEL TECHNIQUES: ULTRASONIC SPRAY PYROLYSIS AND DIP-COATING

    Directory of Open Access Journals (Sweden)

    Ebru Gungor

    2016-08-01

    Full Text Available Undoped and Al-doped ZnO polycrystalline thin films have been fabricated on glass substrates by using a computer-controlled dip coating (DC and ultrasonic spray pyrolysis (USP systems. The film deposition parameters of DC process were optimized for the samples. In this technique, the substrate was exposed to temperature gradient using a tube furnace. In the study, the other solvent-based technique was conventional USP. The zinc salt and Al salt concentrations in the solution were kept constant as 0.1 M and 2% of Zn salt’s molarity, respectively. The optical properties were compared for the films deposited two different techniques. The optical transmission of Al:ZnO/Glass/Al:ZnO sample dip coated and  the optical transmission of Al:ZnO/Glass sample ultrasonically sprayed were determined higher than 80% in the visible and near infrared region. Experimental optical transmittance spectra of the films in the forms of FilmA/Glass/FilmA and FilmA/glass were used to determine the optical constants. It was observed that the optical band gaps of Al doped ZnO films onto glass substrate were increases with increase of Al content and the absorption edge shifted to the shorter wavelength (blue shift compared with the undoped ZnO thin film.

  10. Morphology of carbon nanotubes prepared via chemical vapour deposition technique using acetylene: a small angle neutron scattering investigation

    International Nuclear Information System (INIS)

    Sen, D.; Bahadur, J.; Mazumder, S.; Dasgupta, K.; Sathiyamoorthy, D.

    2008-01-01

    Small angle neutron scattering (SANS) has been utilized to study the morphology of the multi-walled carbon nanotubes prepared by chemical vapour deposition of acetylene. The effects of various synthesis parameters like temperature, catalyst concentration and catalyst support on the size distribution of the nanotubes are investigated. Distribution of nanotube radii in two length scales has been observed. The number density of the smaller diameter tubes was found more in number compared to the bigger one for all the cases studied. No prominent scaling of the structure factor was observed for the different synthesis conditions. (author)

  11. Fiber optic temperature sensor depositing quantum dots inside hollow core fibers using the layer by layer technique

    Science.gov (United States)

    Bravo, Javier; Goicoechea, Javier; Corres, Jesús M.; Arregui, Francisco J.; Matias, Ignacio R.

    2007-07-01

    CdTe Quantum Dots (4 nm of diameter) have been successfully deposited on the inner part of hollow core fibers using the Layer-by-Layer Electrostatic Self-Assembly method. The architecture of the sensor consists on a short section of a hollow core fiber tapered at both ends and spliced to standard multimode optical fibers. Taking advantage of the dependence on temperature of the green fluorescent emission of the Quantum Dot sensitive nanofilms, optical fiber sensors were fabricated and experimentally demonstrated.

  12. Chemical synthesis and characterization of CdSe thin films deposited by SILAR technique for optoelectronic applications

    Directory of Open Access Journals (Sweden)

    K.B. Chaudhari

    2016-12-01

    Full Text Available CdSe thin films were deposited on the glass substrate by successive ionic layer adsorption and reaction (SILAR method. Different sets of the film are prepared by changing the number of immersion cycles as 30, 40, 50 and 60. Further the effect of a number of immersion cycles on the characteristic structural, morphological, optical and electrical properties of the films are studied. The XRD studies revealed that the deposited films showed hexagonal structure with most prominent reflection along (1 0 1 plane. Moreover, the peak intensity of (1 0 1 plane is found to be increased as the number of immersion cycles is increased. All the thin films look relatively smooth and homogeneous covering the entire surface area in FESEM image. Optical properties of the CdSe thin films for a different number of immersion cycles were studied, which indicates that the absorbance increases with the increase in the immersion cycles. Furthermore, the optical band-gap in conjunction with the electrical resistivity was found to get decreased with increase in the immersion cycles. A good correlation between the number of immersion cycles and the physical properties indicates a simple method to manipulate the CdSe material properties for optoelectronic applications.

  13. The effect of thermal annealing on the optical band gap of cadmium sulphide thin films, prepared by the chemical bath deposition technique

    International Nuclear Information System (INIS)

    Ampong, F. K.; Boakye, F.; Asare Donkor, N. K.

    2010-01-01

    Cadmium sulphide thin films have been prepared by the chemical bath deposition technique (ph 11, 70 degree centigrade). Two different sets of films were prepared under varied conditions and concentrations of their ions sources (Cd 2+ from cadmium nitrate, S 2- from thiourea) and Na 2 EDTA as a complexing agent. A UV mini-Schimazu UV-VIS Spectrophotometer was used to determine the optical absorbance of the films as a function of wavelength at room temperature over the wavelength range 200 - 600 nm. The samples were then thermally annealed for thirty minutes, at temperatures of 100 degree centigrade, and 200 degree centigrade, after which the absorbance of the films were again recorded. The band gap values obtained for the sample with 0.5 M CdS as deposited, annealed at 100 degree centigrade and 200 degree centigrade were 2.1 eV, 2.2 eV and 2.3 eV respectively. Whilst the values obtained for the sample 0.15 CdS as deposited, annealed at 100 degree centigrade and annealed at 200 degree centigrade were 2.0 eV, 2.01 eV and 2.02 eV respectively. The increase in band gap with annealing temperature might be attributed to the improvement in crystallinity in the films. (au)

  14. Photoconductivity and surface chemical analysis of ZnO thin films deposited by solution-processing techniques for nano and microstructure fabrication

    International Nuclear Information System (INIS)

    Dwivedi, V. K.; Prakash, G. Vijaya; Srivastava, P.

    2013-01-01

    The fabrication of zinc oxide (ZnO) from inexpensive solution-processing techniques, namely, electrochemical deposition and electrospinning were explored on various conducting and mesoporous semiconducting surfaces. Optimised conditions were derived for template- and self-assisted nano/micro structures and composites. ZnO thin films were annealed at a fixed temperature under ambient conditions and characterised using physical and optical techniques. The photocurrent response in the UV region shows a fast rise and double decay behaviour with a fast component followed by a slow oscillatory decay. Photocurrent results were correlated with surface chemical analysis from X-ray photoelectron spectroscopy. Various characterisation details reveal the importance of fabrication parameter optimisation for useful low-cost optoelectronic applications. (semiconductor materials)

  15. Use of a novel double uterine deposition artificial insemination technique using low concentrations of sperm in pigs.

    Science.gov (United States)

    Mozo-Martín, R; Gil, L; Gómez-Rincón, C F; Dahmani, Y; García-Tomás, M; Úbeda, J L; Grandía, J

    2012-07-01

    Currently, the three most important non-surgical artificial insemination systems used in pigs are the conventional, the post-cervical (IUI), and the deep-intrauterine (DIUI) methods. In this study, a new system, termed double uterine deposition insemination (DUDI), which combines aspects of both IUI and DIUI, was evaluated. This method used a thinner, shorter and more flexible catheter than those normally used for DIUI and resulted in the deposition of semen post-cervically, approximately half-way along the uterine horn, thus potentially by-passing the threat of 'unilateral' insemination or pregnancy when using sperm of low concentration. The experiment was carried out over 8 weeks on a group of 166 sows, which were divided into seven groups, inseminated with semen of varying concentration, using the conventional system (control group) or by DUDI. There were no significant differences in fertility at day 35 post-insemination between the controls and the various DUDI sub-groups. Only sows inseminated with 500 million viable spermatozoa in a total of 30 mL of fluid using the DUDI system demonstrated decreased total litter sizes when compared to conventional insemination (Pinsemination normally uses 2.5-3.5 billion sperm, the findings of this study suggest that DUDI can be used under 'field' conditions with sperm concentrations as low as 750 million spermatozoa in 50-30 mL without any detrimental effect on fertility or litter size. DUDI may provide a viable, robust alternative to IUI and DIUI, and has the potential to become incorporated into on-farm insemination systems. Copyright © 2011 Elsevier Ltd. All rights reserved.

  16. Evaluating the Effect of Surface Roughness on Titanium Dioxide Nanoparticle Deposition using a Combined Quartz Crystal Microbalance with Dissipation (QCM-D) and Generalized Ellipsometry (GE) Technique

    Science.gov (United States)

    Kananizadeh, N.; Lee, J.; Rodenhausen, K. B.; Sekora, D.; Schubert, M.; Schubert, E.; Bartelt-Hunt, S.; Li, Y.

    2016-12-01

    Quantification and characterization of nanoparticles in soils and sediments are very challenging because they will interact not only with soil-water chemistry but also with highly heterogeneous soil and sediment surfaces. In this work, we measured the interaction of Titanium dioxide nanoparticles (nTiO2), the most extensively manufactured engineered materials, with engineered rough surfaces under varied ionic strength conditions. Innovative three-dimensional Silicon nanostructured surfaces, referred to here as slanted columnar thin films (SCTFs), were used to generate surface roughness with controlled heights of 50nm, 100nm, and 200nm. Using atomic layer deposition technique (ALD), surfaces of SCTF were coated with either silicon dioxide or aluminum oxides to represent the most abundant silica aquifer materials and metal oxide impurities, respectively. The interaction between nTiO2 and model rough surfaces was measured using quartz crystal microbalance with dissipation monitoring (QCM-D). The data were analyzed using a model that couples the viscoelastic effect with the surface roughness effect. No nTiO2 deposition was observed on neither flat nor rough silicon dioxide surfaces under ionic strength ranged from 0 to 100 mM NaCl. On the other hand, the deposition of nTiO2 on the aluminum oxides coated surfaces increased as the height of roughness increased. In parallel with QCM-D, a Generalized Ellipsometry (GE) was used to measure the mass of deposited nTiO2. The combination of QCM-D and GE revealed that the properties (i.e. porosity and rigidness) of attached nTiO2 layer on the QCM-D surfaces were dependent on ionic strength and surface roughness.

  17. Co-Deposition of Gold Nanoparticles and Metalloporphyrin Using the Langmuir-Blodgett (LB) Technique for Surface-Enhanced Raman Scattering (SERS).

    Science.gov (United States)

    Camacho, Sabrina A; Aoki, Pedro H B; de Assis, Francisco F; Pires, Ana M; de Oliveira, Kleber T; Aroca, Ricardo F; Constantino, Carlos J L

    2015-04-01

    The synergistic effect produced by metallic nanoparticles when incorporated into different systems empowers a research field that is growing rapidly. In addition, organometallic materials are at the center of intensive research with diverse applications such as light-emitting devices, transistors, solar cells, and sensors. The Langmuir-Blodgett (LB) technique has proven to be suitable to address challenges inherent to organic devices, since the film properties can be tuned at the molecular level. Here we report a strategy to incorporate gold nanoparticles (AuNPs) into the LB film by co-deposition in order to achieve surface-enhanced Raman scattering (SERS) of the zinc(II)-protoporphyrin (IX) dimethyl ester (ZnPPIX-DME). Prior to the LB co-deposition, the properties of the Langmuir monolayer of ZnPPIX-DME at the air-water interface, containing AuNPs in the subphase, are studied through the surface-pressure versus mean molecular area (π-A) isotherms. The ZnPPIX-DME+AuNPs π-A isotherm presented a significant shift to higher molecular area, suggesting an interaction between both ZnPPIX-DME molecules and AuNPs. Those interactions are a key factor allowing the co-deposition of both AuNPs and ZnPPIX-DME molecules onto a solid substrate, thus forming the LB film. SERS of ZnPPIX-DME was successfully attained, ensuring the spatial distribution of the AuNPs. Higher enhancement factors were found at AuNP aggregates, as a result of the intense local electromagnetic field found in the metal nanoparticle aggregates. The main vibrational bands observed in the SERS spectra suggest a physical adsorption of the ZnPPIX-DME onto the surface of AuNPs. The latter is not only in agreement with the interactions pointed out by the π-A isotherms but also suggests that this interaction is kept upon LB film co-deposition.

  18. Titanium dioxide thin films deposited by the sol-gel technique starting from titanium oxy-acetyl acetonate: gas sensing and photocatalyst applications

    Energy Technology Data Exchange (ETDEWEB)

    Maldonado, A.; Mayen-Hernandez, S.A.; L. Olvera, M. de la [Departamento de Ingenieria Electrica-SEES, Centro de Investigacion y de Estudios Avanzados del IPN, CINVESTAV-IPN, Mexico (Mexico); Tirado-Guerra, S. [Escuela Superior de Fisica y Matematicas, Instituto Politecnico Nacional, Mexico (Mexico)

    2010-09-15

    Titanium dioxide (TiO{sub 2}) thin films were deposited onto sodocalcic glass plates by the sol-gel technique, starting from a non-alkoxide route, namely, titanium oxy-acetyl acetonate as Ti precursor. Film thickness effect on both the gas sensing and photocatalytic degradation performance was studied. The as-deposited films were annealed in air at 400 C. All the X-ray spectra of the films show a very broad-peak centered in a 2{theta} angle around 30 . In the case of the thinnest films the surface morphology is uniform and very smooth, whereas for the thickest films the corresponding surface is covered by grains with a rod-like shape with a length on the order of 140 nm. The films were tested both for two straightforward applications: ultraviolet assisted-degradation of methylene blue dissolved in water, at different times, as well as gas sensor in a controlled propane (C{sub 3}H{sub 8}) atmosphere. As the film thickness increases, the degradation of methylene blue (MB) also increases. The thickest TiO{sub 2} thin films after being exposed by 5 hours to the catalytic degradation, promoted by ultraviolet illumination, showed a final MB solution degradation in the order of 48%. This result can be associated with the increase in the effective exposed area of the TiO{sub 2} thin films. On the other hand, the exposition of the films to a controlled propane atmosphere produced a significant change in the surface electrical resistance of the films at operating temperatures of 200 C and above. In fact, in the case of the thickest TiO{sub 2} films, a dramatic electrical resistance change of non-exposed and propane exposed - 560 to 0.7 M{omega} -, was registered. The results show that TiO{sub 2} films deposited by an economical deposition technique, as is the case of the sol-gel technique, could have an important potential in industrial applications. (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  19. Structural properties of perovskite films on zinc oxide nanoparticles-reduced graphene oxide (ZnO-NPs/rGO) prepared by electrophoretic deposition technique

    Science.gov (United States)

    Bahtiar, Ayi; Nurazizah, Euis Siti; Latiffah, Efa; Risdiana, Furukawa, Yukio

    2018-02-01

    Perovskite solar cells highly believed as next generation solar cells to replace currently available inorganic silicon solar cells due to their high power conversion efficiency and easy processing to thin films using solution processing techniques. Performance and stability, however still need to be improved for mass production and widely used for public electricity generation. Perovskite solar cells are commonly deposited on Titanium Dioxide (TiO2) film as an effective electron transport layer (ETL). We used Zinc Oxide nanoparticles (ZnO-NPs) as ETL in perovskite solar cells due to the low temperature required for crystallization and can be formed into different shapes of nanostructures. However, perovskite film can easily degrade into insulating lead iodide due to deprotonation of the methylammoniumcation at the surface of ZnO-NPs, in particular when it stored in ambient air with high relative humidity. The degradation of perovskite layer is therefore needed to be overcome. Here, we capped ZnO-NPs with reduced graphene oxide (rGO) to overcome the degradation of perovskite film where ZnO-NPs is synthesized by sol-gel method. The average nanoparticle size of ZnO is 15 nm. ZnO-NPs and ZnO-NPs-rGO films are prepared using electrophoretic deposition technique, which can produce large area with good homogeneity and high reproducibility. The stability of perovskite layer can significantly be improved by capping ZnO with rGO, which is indicated by absence of color change of perovskite after storage for 5 (five) days in ambient air with relative humidity above 95%. Moreover, the X-Ray Diffaction peaks of perovskite film are more preserved when deposited on ZnO/rGO film than using only ZnO film. We strongly believe, by capping ZnO film with rGO, both the performance and stability of perovskite solar cells can be improved significantly.

  20. Synthesis and self-assembly of dumbbell shaped ZnO sub-micron structures using low temperature chemical bath deposition technique

    Energy Technology Data Exchange (ETDEWEB)

    Borade, P. [National Centre for Nanoscience and Nanotechnology, University of Mumbai, Kalina Campus, Santacruz (E), Mumbai 400098 (India); Joshi, K.U. [Anton-Paar India Pvt. Ltd., Thane (W), 400607 (India); Gokarna, A.; Lerondel, G. [Laboratoire de Nanotechnologie et D' Instrumentation Optique, Institut Charles Delaunay, CNRS UMR 6281, Université de Technologie de Troyes, 12 Rue Marie Curie, BP 2060, 10010 Troyes (France); Walke, P. [National Centre for Nanoscience and Nanotechnology, University of Mumbai, Kalina Campus, Santacruz (E), Mumbai 400098 (India); Late, D. [National Chemical Laboratory (NCL), Pune 400027 (India); Jejurikar, S.M., E-mail: jejusuhas@gmail.com [National Centre for Nanoscience and Nanotechnology, University of Mumbai, Kalina Campus, Santacruz (E), Mumbai 400098 (India)

    2016-02-01

    We report well dispersed horizontal growth of ZnO sub-micron structures using simplest technique ever known i.e. chemical bath deposition (CBD). A set of samples were prepared under two different cases A) dumbbell shaped ZnO grown in CBD bath and B) tubular ZnO structures evolved from dumbbell shaped structures by dissolution mechanism. Single phase wurtzite ZnO formation is confirmed using X-ray diffraction (XRD) technique in both cases. From the morphological investigations performed using scanning electron microscopy (SEM), sample prepared under case A indicate formation of hex bit tool (HBT) shaped ZnO crystals, which observed to self-organize to form dumbbell structures. Further these microstructures are then converted into tubular structures as a fragment of post CBD process. The possible mechanism responsible for the self-assembly of HBT units to form dumbbell structures is discussed. Observed free excitonic peak located at 370 nm in photoluminescence (PL) spectra recorded at 18 K indicate that the micro/nanostructures synthesized using CBD are of high optical quality. - Highlights: • Controlled growth of Dumbbell shaped ZnO using Chemical Bath Deposition (CBD). • Growth mechanism of dumbbell shaped ZnO by self-assembling was discussed. • Quick Transformation of ZnO dumbbell structures in to tubular structures by dissolution. • Sharp UV Emission at 370 nm from both dumbbell and tubular structures.

  1. Deposition of TiN coatings using ACPVD technique on AM60 alloy; Recubrimientos de TiN depositados mediante ACPVD sobre aleaciones de magnesio AM60

    Energy Technology Data Exchange (ETDEWEB)

    Pichel, M.; Candela, N.; Barea, R.; Conejero, G.; Carsi, M.

    2013-06-01

    Magnesium alloys are reaching special interest due to their good specific properties, low cost and good manufacturing properties. However, their low hardness, wear and corrosion resistance limit their applications in certain sectors of industry. These drawbacks can be solved by applying hard ceramic coatings, such as nitrides or metal carbides. TiN is one of the most used coatings due to its high adhesion, hardness, low coefficient of friction and chemical stability. Physical vapor deposition by cathodic arc CAPVD, is a versatile technique, which uses low temperatures and high ionization energies, generating homogeneous coatings. To achieve coatings with high quality, a careful control of the manufacturing parameters is required, such as bias voltage, gas flow or intensity. This paper focuses on magnesium alloys, AM60, coated with TiN using physical vapor deposition cathodic arc technique (CAPVD) at different intensity values (40A and 100A) and surface preparation (grinding up to 4000 grit and polished to 3{mu}m). It was included a final condition with an intermediate Al film. The samples were characterized by X-ray diffraction, roughness, optical microscopy and scanning electron. (Author) 28 refs.

  2. Synthesis and self-assembly of dumbbell shaped ZnO sub-micron structures using low temperature chemical bath deposition technique

    International Nuclear Information System (INIS)

    Borade, P.; Joshi, K.U.; Gokarna, A.; Lerondel, G.; Walke, P.; Late, D.; Jejurikar, S.M.

    2016-01-01

    We report well dispersed horizontal growth of ZnO sub-micron structures using simplest technique ever known i.e. chemical bath deposition (CBD). A set of samples were prepared under two different cases A) dumbbell shaped ZnO grown in CBD bath and B) tubular ZnO structures evolved from dumbbell shaped structures by dissolution mechanism. Single phase wurtzite ZnO formation is confirmed using X-ray diffraction (XRD) technique in both cases. From the morphological investigations performed using scanning electron microscopy (SEM), sample prepared under case A indicate formation of hex bit tool (HBT) shaped ZnO crystals, which observed to self-organize to form dumbbell structures. Further these microstructures are then converted into tubular structures as a fragment of post CBD process. The possible mechanism responsible for the self-assembly of HBT units to form dumbbell structures is discussed. Observed free excitonic peak located at 370 nm in photoluminescence (PL) spectra recorded at 18 K indicate that the micro/nanostructures synthesized using CBD are of high optical quality. - Highlights: • Controlled growth of Dumbbell shaped ZnO using Chemical Bath Deposition (CBD). • Growth mechanism of dumbbell shaped ZnO by self-assembling was discussed. • Quick Transformation of ZnO dumbbell structures in to tubular structures by dissolution. • Sharp UV Emission at 370 nm from both dumbbell and tubular structures.

  3. Characterization of 2004 Indian Ocean tsunami induced deposits along the Chennai coast using magnetic and geochemical techniques

    Digital Repository Service at National Institute of Oceanography (India)

    Veerasingam, S.; Venkatachalapathy, R.

    Present study is the applicability of rock magnetic techniques, coupled with geochemical (SiO2, Al2 O3 , Fe2O3, CaO, MgO, K2O, P2O5, and MnO) and texture size...

  4. Atmospheric depositions of rare earth elements in Albania studied by the moss biomonitoring technique, neutron activation analysis and GIS technology

    International Nuclear Information System (INIS)

    Allajbeu, Sh.; Lazo, P.; Yushin, N.S.; Frontasyeva, M.V.; Qarri, F.; Duliu, O.G.

    2015-01-01

    Rare earth elements (REE) are conservative elements, scarcely derived from anthropogenic sources. The mobilization of REE in the environment requires their monitoring in environmental matrices, where they are mainly present at trace levels. The results on determination of the content of 11 elements by epithermal neutron activation analysis (ENAA) at the IBR-2 reactor in Dubna in carpet-forming moss species Hypnum cupressiforme collected from 44 sampling sites over the whole Albanian territory are presented and discussed. The paper is focused on Sc and lanthanides, as well as Fe and Th, the last ones showing correlations with the investigated REE. With the exception of Fe, all other elements were never determined in the air deposition of Albania. The STATISTICA TM 10 software was used for data analysis. The median values for the content of elements under investigation were compared to those in Bulgaria, Macedonia, Romania and Serbia, as well as Norway selected as a pristine area. Therefore, it was shown that the accumulation of REE in mosses is associated with the wind blown metal-enriched soils that are pointed out as the main emitting factor. [ru

  5. Atmospheric deposition of rare earth elements in Albania studied by the moss biomonitoring technique, neutron activation analysis and GIS technology.

    Science.gov (United States)

    Allajbeu, Sh; Yushin, N S; Qarri, F; Duliu, O G; Lazo, P; Frontasyeva, M V

    2016-07-01

    Rare earth elements (REEs) are typically conservative elements that are scarcely derived from anthropogenic sources. The mobilization of REEs in the environment requires the monitoring of these elements in environmental matrices, in which they are present at trace level. The determination of 11 REEs in carpet-forming moss species (Hypnum cupressiforme) collected from 44 sampling sites over the whole territory of the country were done by using epithermal neutron activation analysis (ENAA) at IBR-2 fast pulsed reactor in Dubna. This paper is focused on REEs (lanthanides) and Sc. Fe as typical consistent element and Th that appeared good correlations between the elements of lanthanides are included in this paper. Th, Sc, and REEs were never previously determined in the air deposition of Albania. Descriptive statistics were used for data treatment using MINITAB 17 software package. The median values of the elements under investigation were compared with those of the neighboring countries such as Bulgaria, Macedonia, Romania, and Serbia, as well as Norway which is selected as a clean area. Geographical distribution maps of the elements over the sampled territory were constructed using geographic information system (GIS) technology. Geochemical behavior of REEs in moss samples has been studied by using the ternary diagram of Sc-La-Th, Spider diagrams and multivariate analysis. It was revealed that the accumulation of REEs in current mosses is associated with the wind-blowing metal-enriched soils that is pointed out as the main emitting factor of the elements under investigation.

  6. Effect of annealing temperature on electrical properties of poly (methyl methacrylate): titanium dioxide nanocomposite films using spin coating deposition technique

    International Nuclear Information System (INIS)

    Ismail, L N; Habibah, Z; Herman, S H; Rusop, M

    2014-01-01

    Nanocomposite poly (methyl methacrylate) :titanium dioxide (PMMA :TiO 2 ) film were deposited on glass substrate. The effect of annealing temperature, especially on electrical, dielectric and the morphological properties of the thin films were investigated by current-voltage (I-V) measurement, impedance spectroscopy, and FESEM. The annealing temperature is varies from 120°C, 140°C, 160°C, 180°C and 200°C. The electrical properties results showing when nanocomposite film annealed at '20°C produce the lowest current. Meanwhile, when the annealing temperature increased, the current increased drastically and this indicates the PMMA:TiO 2 nanocomposite film are no longer having insulating properties. The dielectric properties also indicate that film annealed at 120°C has the best dielectric properties compared to other temperature. The FESEM results show that as the temperature increased, the PMMA:TiO 2 nanocomposite film started to create a phase separation between the PMMA matrix and TiO 2 nanoparticles

  7. Optimization of Process Parameters of Pulsed Electro Deposition Technique for Nanocrystalline Nickel Coating Using Gray Relational Analysis (GRA)

    Science.gov (United States)

    Venkatesh, C.; Sundara Moorthy, N.; Venkatesan, R.; Aswinprasad, V.

    The moving parts of any mechanism and machine parts are always subjected to a significant wear due to the development of friction. It is an utmost important aspect to address the wear problems in present environment. But the complexity goes on increasing to replace the worn out parts if they are very precise. Technology advancement in surface engineering ensures the minimum surface wear with the introduction of polycrystalline nano nickel coating. The enhanced tribological property of the nano nickel coating was achieved by the development of grain size and hardness of the surface. In this study, it has been decided to focus on the optimized parameters of the pulsed electro deposition to develop such a coating. Taguchi’s method coupled gray relational analysis was employed by considering the pulse frequency, average current density and duty cycle as the chief process parameters. The grain size and hardness were considered as responses. Totally, nine experiments were conducted as per L9 design of experiment. Additionally, response graph method has been applied to determine the most significant parameter to influence both the responses. In order to improve the degree of validation, confirmation test and predicted gray grade were carried out with the optimized parameters. It has been observed that there was significant improvement in gray grade for the optimal parameters.

  8. Photocatalytic hydroxyapatite/titanium dioxide multilayer thin film deposited onto glass using an rf magnetron sputtering technique

    Science.gov (United States)

    Ozeki, K.; Janurudin, Juliana M.; Aoki, H.; Fukui, Y.

    2007-01-01

    Hydroxyapatite (HA)/titanium dioxide (TiO2) thin film was deposited on glass using a radio frequency magnetron sputtering. X-ray diffraction (XRD), Fourier-transform infrared spectrometry, ultraviolet-visible spectroscopy and measurement of its photocatalytic activity by the decomposition of formaldehyde gas and the bacterial survival test of Escherichia coli (E. coli) cells were applied to characterize the film. After heat treatment (at 500 °C), XRD analysis of the HA/TiO2 film showed a crystalline TiO2 crystal structure with anatase phase. The transmittance of the HA/TiO2 film decreased after the heat treatment, however, the average transmittance remained at 87% in the visible light range. In the decomposition of formaldehyde gas, the HA/TiO2 film showed a higher decomposition rate than either the TiO2 or the HA film alone. However, in the bacterial survival test, survival of cells on the HA/TiO2 film was higher than that on the TiO2 film, which indicates the HA/TiO2 film has a lower bactericidal effect than the TiO2 film alone.

  9. Technique for controllable vapor-phase deposition of 1-nitro(14C)pyrene and other polycyclic aromatic hydrocarbons onto environmental particulate matter

    International Nuclear Information System (INIS)

    Lucas, S.V.; Lee, K.W.; Melton, C.W.; Lewtas, J.; Ball, L.M.

    1991-01-01

    To produce environmental particles fortified with a polycyclic aromatic hydrocarbon (PAH) for toxicology studies, an experimental apparatus was devised for deposition of the desired chemical species onto particles in a controlled and reproducible manner. The technique utilized consists of dispersion of the particles on a gaseous stream at a controlled rate, thermal vaporization of a solution of PAH, delivery of the vaporized PAH into the aerosol of particles at a controlled rate, subsequent condensation of the PAH onto the particles, and final recovery of the coated particles. The effectiveness of this approach was demonstrated by vapor-coating a 14 C-labeled PAH (1-nitro( 14 C)-pyrene) onto diesel engine exhaust particles that had previously been collected by tunnel dilution sampling techniques. Using the 14 C label as a tracer, the coated particles were characterized with respect to degree of coating, integrity of particle structure and absence of chemical decomposition of the coating substrate. The study demonstrates that the described method provides a controllable means for depositing a substance uniformly and with a high coating efficiency onto aerosolized particles. The technique was also used to vapor-coat benzo(a)pyrene onto diesel engine exhaust and urban ambient air particulate matter, and 2-nitrofluoranthene onto urban ambient air particulate matter. Coating efficiencies of about 400 micrograms/g particulate matter were routinely obtained on a single coating run, and up to 1200 micrograms/g (1200 ppm) were achieved after a second pass through the process. The coated particles were subsequently utilized in biological fate, distribution and metabolism studies

  10. Noninvasive radioisotopic technique for detection of platelet deposition in mitral valve prosthesis and renal microembolism in dogs

    International Nuclear Information System (INIS)

    Dewanjee, M.K.; Kaye, M.P.; Fuster, V.; Rao, S.A.

    1980-01-01

    At 24 hrs after implantation of Bjoerk-Shiley mitral prosthesis in 5 dogs, in vivo images were obtained with a gamma camera after intravenous administration (0.5-0.6 mCi) one hour postoperatively of autologous Indium-111-labeled platelets. The site of platelet deposition in the teflon ring and perivascular damaged cardiac tissue is clearly delineated in the scintiphoto. In vitro biodistribution (mean % +/- SD of injected dose) at 24 hrs after injection of the 5 implanted and 7 normal dogs performed with a gamma counter demonstrated that (45.1 +/- 10.6)% and (0.7 +/- 0.4)% were in blood and kidneys in normal dogs and (28.5 +/- 6.8)%, (1.6 +/- 0.6)%, (0.3 +/- 0.1)%, and (0.2 +/- 0.1)% were in blood, kidneys, teflon rings, and perivascular damaged cardiac tissue, respectively. The strut and pyrolytic carbon-coated disc retained only (0.0033 +/- 0.0004)% and (0.0031 +/- 0.0003)%, respectively. There was a 2.3-fold increase of labeled platelets in kidneys of implanted dogs due to renal trapping of microembolism. Also, three- to fivefold increase in ratios of lung, brain, cardiac, and skeletal muscle to blood indicates that internal organs and whole body work as filter for microembolism generated by cardiovascular surgery and mitral prosthesis. Twenty percent of the administered platelets are consumed in surgical repair of damaged tissue. Indium-111-labeled platelets thus provide a sensitive marker for noninvasive imaging of Bjoerk-Shiley mitral prosthesis, thromboembolism after implantation of prosthetic device, and in vitro quantitation of surgical consumption

  11. Application of Fractal Technique for Analysis of Geophysical - Geochemical Databases in Tekieh Pb-Zn Ore Deposit (SE of Arak)

    International Nuclear Information System (INIS)

    Mehrnia, S.R.

    2017-01-01

    In this research, two statistical techniques that consist of classical and fractal equations (Mandelbrot, 2005) were applied in geochemical (Torkashvand et al., 2009) and geophysical (Jafari, 2007) databases for obtaining the linear and nonlinear distributions of geochemical elements (Tekieh Pb-Zn content) in association with resistivity variations and induction polarization measurements (Calagari, 2010). According to linear statistical techniques (Torkashvand et al., 2009), the main central parameters such as mean, median and mode in addition to variances and standard deviations as distribution tendencies could be used for obtaining the regression coefficients of the databases. However, in fractal statistics, a reliable regression between geo electrical - geochemical anomalies should be calculated based on measuring the fractal dimensional variations in the recursive patterns (Mehrnia, 2013). In practice, the Area-Concentration equations (Mandelbrot, 2005) were applied in resistivity, induction polarization, Pb and Zn datasets for achieving the nonlinear relationships in anomalous regions which were characterized by increasing in regression coefficients with more spatial correlation of the variable than linear statistics (Mehrnia, 2013).

  12. Development of graded Ni-YSZ composite coating on Alloy 690 by Pulsed Laser Deposition technique to reduce hazardous metallic nuclear waste inventory.

    Science.gov (United States)

    Sengupta, Pranesh; Rogalla, Detlef; Becker, Hans Werner; Dey, Gautam Kumar; Chakraborty, Sumit

    2011-08-15

    Alloy 690 based 'nuclear waste vitrification furnace' components degrade prematurely due to molten glass-alloy interactions at high temperatures and thereby increase the volume of metallic nuclear waste. In order to reduce the waste inventory, compositionally graded Ni-YSZ (Y(2)O(3) stabilized ZrO(2)) composite coating has been developed on Alloy 690 using Pulsed Laser Deposition technique. Five different thin-films starting with Ni80YSZ20 (Ni 80 wt%+YSZ 20 wt%), through Ni60YSZ40 (Ni 60 wt%+YSZ 40 wt%), Ni40YSZ60 (Ni 40 wt%+YSZ 60 wt%), Ni20YSZ80 (Ni 20 wt%+YSZ 80 wt%) and Ni0YSZ100 (Ni 0 wt%+YSZ 100 wt%), were deposited successively on Alloy 690 coupons. Detailed analyses of the thin-films identify them as homogeneous, uniform, pore free and crystalline in nature. A comparative study of coated and uncoated Alloy 690 coupons, exposed to sodium borosilicate melt at 1000°C for 1-6h suggests that the graded composite coating could substantially reduced the chemical interactions between Alloy 690 and borosilicate melt. Copyright © 2011 Elsevier B.V. All rights reserved.

  13. Effects of Surface Modification of Nanodiamond Particles for Nucleation Enhancement during Its Film Growth by Microwave Plasma Jet Chemical Vapour Deposition Technique

    Directory of Open Access Journals (Sweden)

    Chii-Ruey Lin

    2014-01-01

    Full Text Available The seedings of the substrate with a suspension of nanodiamond particles (NDPs were widely used as nucleation seeds to enhance the growth of nanostructured diamond films. The formation of agglomerates in the suspension of NDPs, however, may have adverse impact on the initial growth period. Therefore, this paper was aimed at the surface modification of the NDPs to enhance the diamond nucleation for the growth of nanocrystalline diamond films which could be used in photovoltaic applications. Hydrogen plasma, thermal, and surfactant treatment techniques were employed to improve the dispersion characteristics of detonation nanodiamond particles in aqueous media. The seeding of silicon substrate was then carried out with an optimized spin-coating method. The results of both Fourier transform infrared spectroscopy and dynamic light scattering measurements demonstrated that plasma treated diamond nanoparticles possessed polar surface functional groups and attained high dispersion in methanol. The nanocrystalline diamond films deposited by microwave plasma jet chemical vapour deposition exhibited extremely fine grain and high smooth surfaces (~6.4 nm rms on the whole film. These results indeed open up a prospect of nanocrystalline diamond films in solar cell applications.

  14. Sn and Cu oxide nanoparticles deposited on TiO{sub 2} nanoflower 3D substrates by Inert Gas Condensation technique

    Energy Technology Data Exchange (ETDEWEB)

    Kusior, A., E-mail: akusior@agh.edu.pl [Faculty of Materials Science and Ceramics, AGH University of Science and Technology, al. Mickiewicza 30, 30-059 Krakow (Poland); Kollbek, K. [Academic Centre for Materials and Nanotechnology, AGH University of Science and Technology, al. Mickiewicza 30, 30-059 Krakow (Poland); Kowalski, K. [Faculty of Metals Engineering and Industrial Computer Science, AGH University of Science and Technology, al. Mickiewicza 30, 30-059 Krakow (Poland); Borysiewicz, M. [Institute of Electron Technology, al. Lotnikow 32/46, 02-668 Warszawa (Poland); Wojciechowski, T. [Institute of Physics Polish Academy of Science, al. Lotnikow 32/46, 02-668 Warszawa (Poland); Adamczyk, A.; Trenczek-Zajac, A.; Radecka, M. [Faculty of Materials Science and Ceramics, AGH University of Science and Technology, al. Mickiewicza 30, 30-059 Krakow (Poland); Zakrzewska, K. [Faculty of Computer Science, Electronics and Telecommunications, AGH University of Science and Technology, al. Mickiewicza 30, 30-059 Krakow (Poland)

    2016-09-01

    Graphical abstract: - Highlights: • Inert Gas Condensation method yields non-agglomerated nanoparticles. • The growth of nanoparticles is controllable at the level of deposition. • Electrical conductivity increases with respect to pure nanostructured TiO{sub 2}. - Abstract: Sn and Cu oxide nanoparticles were deposited by Inert Gas Condensation (IGC) technique combined with dc magnetron sputtering onto nanoflower TiO{sub 2} 3D substrates obtained in the oxidation process of Ti-foil in 30% H{sub 2}O{sub 2}. Sputtering parameters such as insertion length and Ar/He flow rates were optimized taking into account the nanostructure morphology. Comparative studies with hydrothermal method were carried out. Surface properties of the synthesized nanomaterials were studied by Scanning Electron Microscopy, SEM, Atomic Force Microscopy, AFM, and X-ray Photoelectron Spectroscopy, XPS. X-ray diffraction, XRD and Raman spectroscopy were performed in order to determine phase composition. Impedance spectroscopy demonstrated the influence of nanoparticles on the electrical conductivity.

  15. Anti-microbial surfaces: An approach for deposition of ZnO nanoparticles on PVA-Gelatin composite film by screen printing technique.

    Science.gov (United States)

    Meshram, J V; Koli, V B; Phadatare, M R; Pawar, S H

    2017-04-01

    Initially micro-organisms get exposed to the surfaces, this demands development of anti-microbial surfaces to inhibit their proliferation. Therefore, herein, we attempt screen printing technique for development of PVA-GE/ZnO nanocomposite (PG/ZnO) films. The synthesis of PG/ZnO nanocomposite includes two steps as: (i) Coating of Zinc Oxide nanoparticles (ZnO NPs) by poly ethylene glycol in order to be compatible with organic counterparts. (ii) Deposition of coated nanoparticles on the PG film surface. The results suggest the enhancement in anti-microbial activity of PG/ZnO nanocomposite over pure ZnO NPs against both Gram positive Bacillus subtilis and Gram negative Escherichia coli from zone of inhibition. The uniformity in deposition is further confirmed by scanning electron microscopy (SEM) images. The phase identification of ZnO NPs and formation of PG/ZnO nanocomposite has been confirmed by X-ray diffraction (XRD) analysis and UV-vis spectroscopy (UV-vis). The Attenuated total reflection Spectroscopy (ATR) analysis indicates the ester bond between PVA and gelatin molecules. The thermal stability of nanocomposite is studied by thermogravimetric analysis (TGA) revealing increase in crystallinity due to ZnO NPs which could be utilized to inhibit the growth of micro-organisms. The tensile strength is found to be higher and percent elongation is double of PG/ZnO nanocomposite than PG composite film. Copyright © 2016. Published by Elsevier B.V.

  16. Effect of complexing agent TEA: The structural, morphological, topographical and optical properties of FexSx nano thin films deposited by SILAR technique

    Science.gov (United States)

    Manikandan, K.; Mani, P.; Surendra Dilip, C.; Valli, S.; Fermi Hilbert Inbaraj, P.; Joseph Prince, J.

    2014-01-01

    Iron sulfide thin films (FexSx) (x = 0.05 M, 0.10 M, 0.15 M, 0.20 M and 0.25 M) were deposited by SILAR method from equimolar and equivolume aqueous solutions of ferrous nitrate and sodium sulfide with the addition of complexing agent TEA. The structural, morphological and optical characteristics of the films were derived from X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM) and UV-vis spectral techniques. The mixed characteristics (crystalline and amorphous) of the deposited films and the increasing crystalline qualities with the concentrations were understood from the XRD analysis. The grain sizes and roughness of the films were decreases with the increasing concentration and also at the higher concentration films are shown by the same images presence of hexagonal like crystallite structure. The influence of complexing agent TEA on the surface roughness and morphological properties are confirmed by the atomic force microscope (AFM) results. The effect of increasing substrate concentration on the absorption and transmission measurements and its impact on the optical band-gap energy were enumerated from the UV-vis analysis.

  17. Hydrogen-related defects in Al2O3 layers grown on n-type Si by the atomic layer deposition technique

    Science.gov (United States)

    Kolkovsky, Vl.; Stübner, R.

    2018-04-01

    The electrical properties of alumina films with thicknesses varying from 15 nm to 150 nm, grown by the atomic layer deposition technique on n-type Si, were investigated. We demonstrated that the annealing of the alumina layers in argon (Ar) or hydrogen (H) atmosphere at about 700 K resulted in the introduction of negatively charged defects irrespective of the type of the substrate. These defects were also observed in samples subjected to a dc H plasma treatment at temperatures below 400 K, whereas they were not detected in as-grown samples and in samples annealed in Ar atmosphere at temperatures below 400 K. The concentration of these defects increased with a higher H content in the alumina films. In good agreement with theory we assigned these defects to interstitial H-related defects.

  18. Characterization of ion beam sputtered deposited W/Si multilayers by grazing incidence x-ray diffraction and x-ray reflectivity technique

    Science.gov (United States)

    Dhawan, Rajnish; Rai, Sanjay

    2016-05-01

    W/Si multilayers four samples have been deposited on silicon substrate using ion beam sputtering system. Thickness of tungsten (W) varies from around 10 Å to 40 Å while the silicon (Si) thickness remains constant at around 30 Å in multilayers [W-Si]x4. The samples have been characterized by grazing incidence X-ray diffraction (GIXRD) and X-ray reflectivity technique (XRR). GIXRD study shows the crystalline behaviour of W/Si multilayer by varying W thickness and it is found that above 20 Å the W film transform from amorphous to crystalline phase and X-ray reflectivity data shows that the roughnesses of W increases on increasing the W thicknesses in W/Si multilayers.

  19. Effect of Mn doping on the electrical and optical properties of SnO{sub 2} thin films deposited by chemical spray pyrolysis technique

    Energy Technology Data Exchange (ETDEWEB)

    Indira Gandhi, T. [Crystal Growth and Thin Film Laboratory, Department of Physics, Bharathidasan University, Tiruchirappalli 620 024, Tamil Nadu (India); Ramesh Babu, R., E-mail: rampap2k@yahoo.co.in [Crystal Growth and Thin Film Laboratory, Department of Physics, Bharathidasan University, Tiruchirappalli 620 024, Tamil Nadu (India); Ramamurthi, K. [Crystal Growth and Thin Film Laboratory, Department of Physics and Nanotechnology, Faculty of Engineering and Technology, SRM University, Kattankulathur 603 203, Tamil Nadu (India); Arivanandhan, M. [Nanodevices and Nanomaterials Division, Research Institute of Electronics, Shizuoka University, Hamamatsu 432 8011 (Japan)

    2016-01-01

    Manganese doped tin oxide (Mn:SnO{sub 2}) thin films were deposited by spray pyrolysis technique adding various concentrations of manganese acetate (0–8 at.%) in the spray solution of tin chloride. X-ray diffraction studies show the preferred growth along (301) direction for 0.0–2.0 at.% concentration of manganese acetate in the spray solution. Higher doping concentration of manganese acetate (4 and 8 at.%) in the solution shifts the preferred growth direction along (200) plane. Scanning electron microscopic studies reveal the change in the surface morphology of the films due to various levels of Mn doping. X-ray photoelectron spectroscopic analysis shows that in the prepared thin film manganese atoms exist in Mn{sup 3+} state. The sheet resistance of SnO{sub 2} film decreases from ~ 23.5 Ω/□ to 22.8 Ω/□ for 0.4 at.% doping concentration and increases with increasing Mn concentration in the solution. The average optical transmittance of SnO{sub 2} thin film increases from 34% to 55% in the wavelength region of 550–850 nm with increase in Mn concentration. Mn concentration in the films influences the intensity of the photoluminescence emission peak observed for SnO{sub 2} film at 398 nm. - Highlights: • Mn:SnO2 thin films deposited with different doping concentration by spray pyrolysis technique • Structural information confirms that all the films are polycrystalline and tetragonal crystal structure. • XPS studies confirm the oxidation state of Mn (3 +) and Sn (4 +) in Mn:SnO{sub 2} thin film. • 0.4 at.% of Mn:SnO{sub 2} thin film shows lowest sheet resistance 22.8 Ω/□. • Optical band gap of 1.2 at.% Mn:SnO{sub 2} thin film is about 3.70 eV.

  20. Erosion and sediment deposition evaluation on a slope under pasture in Jandaia-GO using the '137Cs fallout' technique

    International Nuclear Information System (INIS)

    Arthur, Robson C.J.; Bacchi, Osny O.S.; Reichardt, Klaus; Oliveira, Carloeme Alves de; Correchel, Vladia

    2009-01-01

    Water erosion is one of the main forms of soil degradation and among the diverse factors that affect it, two of great importance are the soil cover and slope. Estimates of sediment distribution rates associated to the different uses and soil management practices are scarce and the employed methods in these determinations are in general costly and time consuming. Rates of sediment redistribution evaluated by means of the 137 Cs technique are based on the comparison of inventories of individual points of a given position and an inventory of reference, whose value represents the amount of 137 Cs of 'fallout' origin that was added to the local site. This allows evaluating situations of losses and accumulations of sediments by the erosive process. The objective of the present work was to analyze the sediment production in a pasture area and to measure the efficiency of riparian forests in trapping the erosion sediments coming from pasture, through the ' 137 Cs fallout' redistribution analysis. The study was carried out in Jandaia/GO, Brazil, in two dowslope transects located in a pasture area. Samples were taken from seven points of two 140 m long transects, as well as from three soil profiles of a 15 m transect in the downstream riparian forests of each transect. Soil profiles were sampled in three layers of 20 cm (0-20, 20-40 and 40-60). The soil samples were air dried, sieved and then analyzed for 137 Cs activity by a gamma ray detector (GEM-20180P, EG and ORTEC) coupled to a multichannel analyzer at CENA/USP. The results indicate variations of 137 Cs activity in soil profiles and high erosion rates to the riparian forest to the pasture areas of the two transects, showing sediment movement from the pasture area to the riparian forest, which suggests that the current width of the forest is not wide enough to trap the sediments produced upslope in the pasture area. (author)

  1. A study on the structural and mechanical properties of nanocrystalline CuS thin films grown by chemical bath deposition technique

    International Nuclear Information System (INIS)

    Mukherjee, Nillohit; Sinha, Arijit; Khan, Gobinda Gopal; Chandra, Debraj; Bhaumik, Asim; Mondal, Anup

    2011-01-01

    We report a chemical route for the deposition of nanocrystalline thin films of CuS, using aqueous solutions of Cu(CH 3 COO) 2 , SC(NH 2 ) 2 and N(CH 2 CH 2 OH) 3 [triethanolamine, i.e. TEA] in proper concentrations and ratios. The films were structurally characterized using X-ray diffraction technique (XRD), field emission scanning electron microscopy (FESEM) and optical analysis [both photo luminescence (PL) and ultraviolet-visible (UV-vis)]. Optical studies showed a large blue shift in the band gap energy of the films due to quantum confinement effect exerted by the nanocrystals. From both XRD and FESEM analyses, formation of CuS nanocrystals with sizes within 10-15 nm was evident. A study on the mechanical properties was carried out using nanoindentation and nanoscratch techniques, which showed good mechanical stability and high adherence of the films with the bottom substrate. Such study on the mechanical properties of the CuS thin films is being reported here for the first time. Current-voltage (I-V) measurements were also carried out for the films, which showed p-type conductivity.

  2. Application of the electrophoretic deposition technique for obtaining Yttria-stabilized zirconia tubes; Aplicacao da tecnica de deposicao eletroforetica para a obtencao de tubos ceramicos de zirconia-itria

    Energy Technology Data Exchange (ETDEWEB)

    Caproni, E.; Muccillo, R., E-mail: ecaproni@gmail.com, E-mail: muccillo@usp.br [Centro de Ciencia e Tecnologia de Materiais, Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2012-01-15

    The electrophoretic deposition (EPD) is recognized as the most versatile technique for processing particulate materials, due to low cost, deposition in minutes and forming of pieces with complex geometry shapes. In this work an experimental setup for the simultaneous conformation of 16 ceramic tubes by EPD was built. Bimodal submicron Yttria-stabilized zirconia particles were deposited into graphite electrodes, after suitably adjusting the rheological characteristics of the suspension in isopropanol. After graphite burning and YSZ sintering at 1500 deg C, the ceramic tubes were characterized by X-ray diffraction, scanning probe microscope, impedance spectroscopy and electrical response as a function of oxygen content. Small dense one end-closed ceramic tubes, fully stabilized in the cubic phase, were successfully obtained by the EPD technique, showing the ability of that technique for processing large quantities of tubular solid electrolytes with electrical response to different amounts of oxygen according to the Nernst law (author)

  3. Synthesis of core/shell ZnO/ZnSe nanowires using novel low cost two-steps electrochemical deposition technique

    Energy Technology Data Exchange (ETDEWEB)

    Ghoul, M., E-mail: ghoulmed2009@yahoo.fr [Laboratoire Photovoltaïque, Centre de Recherches et des Technologies de l' Energie Technopole BorjCedria, Bp 95, Hammammlif 2050 (Tunisia); Braiek, Z. [Laboratoire Photovoltaïque, Centre de Recherches et des Technologies de l' Energie Technopole BorjCedria, Bp 95, Hammammlif 2050 (Tunisia); Brayek, A. [Laboratoire Photovoltaïque, Centre de Recherches et des Technologies de l' Energie Technopole BorjCedria, Bp 95, Hammammlif 2050 (Tunisia); ITODYS, Université Paris Diderot, Sorbonne Paris Cité, CNRS UMR – 7086, 75205 Paris (France); Ben Assaker, I.; Khalifa, N.; Ben Naceur, J.; Souissi, A.; Lamouchi, A. [Laboratoire Photovoltaïque, Centre de Recherches et des Technologies de l' Energie Technopole BorjCedria, Bp 95, Hammammlif 2050 (Tunisia); Ammar, S. [ITODYS, Université Paris Diderot, Sorbonne Paris Cité, CNRS UMR – 7086, 75205 Paris (France); Chtourou, R. [Laboratoire Photovoltaïque, Centre de Recherches et des Technologies de l' Energie Technopole BorjCedria, Bp 95, Hammammlif 2050 (Tunisia)

    2015-10-25

    This work highlights the original use of a two-step electrochemical deposition protocol to grow ZnO/ZnSe core/shell nanowires on a Sn-doped In{sub 2}O{sub 3} (ITO)/glass substrate. The good alignment of the nanowires is verified by the scanning electron microscopy characterization technique in addition to the surface roughness after the ZnSe electrodeposition on the ZnO nanowires lateral facets. The X-ray diffraction patterns and Raman spectra allow estimating that ZnO has grown along the wurtzite (W) structure c-axis. The presence of the type-II interfacial transition between the valence band of ZnSe and the conduction band of ZnO was confirmed by UV–visible spectroscopy. It was proved that the absorbed energy of the developed nanostructures is extended to the near infrared which is well recommended for the photovoltaic applications. - Graphical abstract: Fabrication of the ZnO–ZnSe core–shell nanowires through a solution based all-electrochemical approach, and their application as photoanodes in photoelectrochemical water splitting cells. - Highlights: • Deposition of ZnO/ZnSe nanowires by two steps electrodeposition method. • The morphology studies show the formation of ZnO/ZnSe core/Shell nanowires. • XRD and Raman spectroscopy confirm the presence of the wurtzite ZnO and blende ZnSe junction. • Optical properties demonstrate the evidence type-II interfacial transition between the two semiconductors.

  4. Synthesis and characterization of Bi{sub 1−x}Nd{sub x}FeO{sub 3} thin films deposited using a high throughput physical vapour deposition technique

    Energy Technology Data Exchange (ETDEWEB)

    Darby, M.S.B., E-mail: darbymsb@gmail.com [Department of Materials, Science and Engineering, University of Sheffield, Sheffield, S1 3JD (United Kingdom); Karpinsky, D.V. [Complexo de Laboratórios Tecnológicos, Campus Universitário de Santiago, 3810-193 Aveiro (Portugal); Pokorny, J. [Department of Materials, Science and Engineering, University of Sheffield, Sheffield, S1 3JD (United Kingdom); Institute of Physics, Academy of Sciences of the Czech Republic, 182 21 Prague (Czech Republic); Guerin, S. [Ilika Technologies Limited, Kenneth Dibben House, Enterprise Road, University of Southampton Science Park, Chilworth, Southampton, SO16 7NS (United Kingdom); Kholkin, A.L. [Complexo de Laboratórios Tecnológicos, Campus Universitário de Santiago, 3810-193 Aveiro (Portugal); Miao, S. [Department of Materials, Science and Engineering, University of Sheffield, Sheffield, S1 3JD (United Kingdom); Hayden, B.E. [Ilika Technologies Limited, Kenneth Dibben House, Enterprise Road, University of Southampton Science Park, Chilworth, Southampton, SO16 7NS (United Kingdom); Reaney, I.M. [Department of Materials, Science and Engineering, University of Sheffield, Sheffield, S1 3JD (United Kingdom)

    2013-03-01

    The high throughput synthesis of BiFeO{sub 3} and rare earth doped BiFeO{sub 3} films using a modified molecular beam epitaxy technique is reported. Optimum conditions for deposition have been established and compositionally graded Bi{sub (1−x)}Nd{sub x}FeO{sub 3} (x = 0.08 to 0.24) thin films have been fabricated on platinised silicon substrate (Si/SiO{sub 2}/TiO{sub 2}/Pt) with the aim of finding the optimum Nd dopant concentrations for enhanced piezoelectric properties. For x < 0.12, the structure and symmetry were identical to that of the R3c BiFeO{sub 3} end member. For x > 0.20, the structure and symmetry were consistent with the NdFeO{sub 3} end member (Pnma). For compositions 0.12 < x < 0.2, a gradual transition from R3c to Pnma was observed via a mixed phase region but no compositional interval could be unambiguously identified in which the intermediate PbZrO{sub 3}-like structure, reported by Karimi et al. (2009) [6], existed as a single phase. Piezoresponse force microscopy remanent hysteresis measurements of the film revealed a statistical increase in the piezoelectric response at x ≈ 0.11 within the R3c region adjacent to the mixed phase field. - Highlights: ► High throughput synthesis and characterization of BiFeO3 and Nd-doped BiFeO3 films ► The piezoelectric properties of compositionally graded bismuth ferrite are studied. ► The structure and phase assemblage of Nd-doped bismuth ferrite have been studied.

  5. Potentials and pitfalls of depth profile (10Be), burial isochron (26Al/10Be) and palaeomagnetic techniques for dating Early Pleistocene terrace deposits of the Moselle valley (Germany)

    Science.gov (United States)

    Rixhon, Gilles; Cordier, Stéphane; May, Simon Matthias; Kelterbaum, Daniel; Szemkus, Nina; Keulertz, Rebecca; Dunai, Tibor; Binnie, Steven; Hambach, Ulrich; Scheidt, Stephanie; Brueckner, Helmut

    2016-04-01

    Throughout the river network of the Rhenish Massif the so-called main terraces complex (MTC) forms the morphological transition between a wide upper palaeovalley and a deeply incised lower valley. The youngest level of this complex (YMT), directly located at the edge of the incised valley, represents a dominant geomorphic feature; it is often used as a reference level to identify the beginning of the main middle Pleistocene incision episode (Demoulin & Hallot, 2009). Although the main terraces are particularly well preserved in the lower Moselle valley, a questionable age of ca. 800 ka is assumed for the YMT, mainly based on the uncertain extrapolation of controversially interpreted palaeomagnetic data obtained in the Rhine valley. In this study, we applied terrestrial cosmogenic nuclide (TCN) dating (10Be/26Al) and palaeomagnetic dating to Moselle fluvial sediments of the MTC. To unravel the spatio-temporal characteristics of the Pleistocene evolution of the valley, several sites along the lower Moselle were sampled following two distinct TCN dating strategies: depth profiles where the original terrace (palaeo-) surface is well preserved and did not experience a major post-depositional burial (e.g., loess cover); and the isochron technique, where the sediment thickness exceeds 4.5-5 m. One terrace deposit was sampled for both approaches (reference site). In addition, palaeomagnetic sampling was systematically performed in each terrace sampled for TCN measurements. The TCN dating techniques show contrasting results for our reference site. Three main issues are observed for the depth profile method: (i) an inability of the modeled profile to constrain the 10Be concentration of the uppermost sample; (ii) an overestimated density value as model output; and (iii) a probable concentration steady state of the terrace deposits. By contrast, the isochron method yields a burial age estimate of 1.26 +0.29/-0.25 Ma, although one sample showed a depleted 26Al/10Be ratio

  6. Y/sub 1/Ba/sub 2/Cu/sub 3/O/sub 7-//sub delta/ thin films grown by a simple spray deposition technique

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, A.; Koren, G.; Giess, E.A.; Moore, N.R.; O' Sullivan, E.J.M.; Cooper, E.I.

    1988-01-11

    The preparation of high T/sub c/ superconducting thin films of Y/sub 1/Ba/sub 2/Cu/sub 3/O/sub 7-//sub delta/ on (100) single crystals of MgO, ZrO/sub 2/ with 9% Y/sub 2/O/sub 3/ (yttria stabilized zirconia, or YSZ), and SrTiO/sub 3/ using a simple spray deposition technique is described. Typical film growth procedure involves (a) the spraying of a stoichiometric solution of the nitrate precursors on the heated substrate (180 /sup 0/C), (b) prebaking in air of the sprayed film (20 min at 500 /sup 0/C), and (c) oven annealing of the film under flowing O/sub 2/ (900--950 /sup 0/C followed by slow cooling to 200 /sup 0/C in about 3 h). X-ray diffraction analysis of the films after each of the growing steps mentioned above shows primarily the presence of crystalline phases of the nitrates, the oxides, and the orthorhombic superconducting phase, respectively. Resistivity versus temperature measurements show that the onset and completion of the superconductive transition occur at 92 and 87 K, respectively, in films on YSZ substrate; at 95 and 80 K, respectively, in films on SrTiO/sub 3/ substrate; and at 82 and 77 K, respectively, in films on MgO substrate.

  7. Thermoluminescent dosimetry and of optically stimulated luminescence of diamond films grown up by the chemical vapor deposition technique exposed to beta radiation

    International Nuclear Information System (INIS)

    Melendrez A, R.; Barboza F, M.

    2002-01-01

    A study of the dosimetric properties through the thermoluminescence (Tl) and Optically stimulated luminescence (Lobe) in diamond films grown up by the chemical vapor deposition (Dq) techniques was realized.The films under study have thickness of 6, 12, 180 and 500 microns. The dose range was from 0 to 1.5 KGy, observing for the case of the thermoluminescent dosimetry a linear behavior in the range 0-300 Gy and a supra linearity effect in the range from 300-1500 Gy. For the case of the dosimetry by means of LOE a linear behavior in the range (0-300 Gy) without be enough for the saturation was observed, although some samples exhibit a linear behavior until 1500 Gy (6 microns). The irradiation was realized with a source of Strontium 90 of (40 mCi) and the photoestimulation for realizing the measures of LOE was realized using diodes emitting of laser light (470 nm) which generate until 50 MW/cm 2 . The Tl peak which was used to realize the dosimetry such Tl as LOE was that located around 340 C degrees in the brilliance curve which presents another peaks centered around of 110, 190, and 340 C degrees, depending on the film. It was realized a study of the Tl signal drop and it was observed that after 3 hours the signal was stable reaching a decay of 15 %. the analysis of the drop in the Tl signal, immediately after to irradiate and after to photoestimulate with the blue light laser for observing the LOE, indicated that exists a fall in all the Tl peaks, decaying in greater proportion those of more low temperature. (Author)

  8. Synthesis and characterization of Bi.sub.1-x./sub.Nd.sub.x./sub.FeO.sub.3./sub. thin films deposited using a high throughput physical vapour deposition technique

    Czech Academy of Sciences Publication Activity Database

    Darby, M.S.B.; Karpinsky, D.V.; Pokorný, Jan; Guerin, D.; Kholkin, A. L.; Miao, S.; Haydn, B.E.; Reaney, I. M.

    2013-01-01

    Roč. 531, MAR (2013), s. 56-60 ISSN 0040-6090 Institutional support: RVO:68378271 Keywords : bismuth ferrite * piezoelectric * neodymium doped * high throughput * combinatorial * physical vapour deposition Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.867, year: 2013 http://www.sciencedirect.com/science/article/pii/S004060901201646X

  9. Vapor deposition of tantalum and tantalum compounds

    International Nuclear Information System (INIS)

    Trkula, M.

    1996-01-01

    Tantalum, and many of its compounds, can be deposited as coatings with techniques ranging from pure, thermal chemical vapor deposition to pure physical vapor deposition. This review concentrates on chemical vapor deposition techniques. The paper takes a historical approach. The authors review classical, metal halide-based techniques and current techniques for tantalum chemical vapor deposition. The advantages and limitations of the techniques will be compared. The need for new lower temperature processes and hence new precursor chemicals will be examined and explained. In the last section, they add some speculation as to possible new, low-temperature precursors for tantalum chemical vapor deposition

  10. Quality CuInSe2 and Cu(In,Ga)Se2 thin films processed by single-step electrochemical deposition techniques

    Science.gov (United States)

    Papadimitriou, D.; Roupakas, G.; Sáez-Araoz, R.; Lux-Steiner, M.-Ch; Nickel, N. H.; Alamé, S.; Vogt, P.; Kneissl, M.

    2015-05-01

    Ternary CuInSe2 and quaternary Cu(In,Ga)Se2 chalcopyrite semiconductor films with potential applications as solar absorbers were deposited by single-step electrochemical deposition (ECD) on molybdenum coated glass substrates. The films have been structurally characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM) combined with energy dispersive x-ray analysis (EDAX), x-ray photoelectron spectroscopy (XPS), and Raman spectroscopy. Chalcopyrite phase formation was confirmed already in as-deposited films. The crystal structure of the films was further improved by thermal treatment. Element interdiffusion at the chalcopyrite/Mo/glass interface has been prevented by retaining moderate temperatures of deposition (70 °C) and subsequent annealing (300 °C). The SEM/EDAX analysis revealed the presence of CuxSe secondary phases on the surface of ternary films and almost stoichiometric growth of quaternary deposited on top of ternary films. The XRD and Raman analysis confirmed the high quality assessment of the films being almost equal to that of chalcopyrite selenide layers grown by physical vapor deposition at high temperatures (550-750 °C). The surface sensitive XPS analysis confirmed the absence of other impurities in the ECD processed films except from oxygen and carbon adsorbents by sample exposure to atmospheric air.

  11. Characteristics of Nanocrystallite-CdS Produced by Low-Cost Electrochemical Technique for Thin Film Photovoltaic Application: The Influence of Deposition Voltage

    Directory of Open Access Journals (Sweden)

    Obi Kingsley Echendu

    2017-01-01

    Full Text Available Electrochemical deposition and characterization of nanocrystallite-CdS thin films for thin film solar cell application are reported. The two-electrode system used provides a relatively simple and cost-effective approach for large-scale deposition of semiconductors for solar cell and other optoelectronic device application. Five CdS thin films were deposited for 45 minutes each at different cathodic deposition voltages in order to study their properties. X-ray diffraction study reveals that the as-deposited films contain mixed phases of hexagonal and cubic CdS crystallites with large amounts of internal strain and dislocation density. Postdeposition annealing results in phase transformation which leaves the films with only the hexagonal crystal phase and reduced strain and dislocation density while increasing the crystallite sizes from 21.0–42.0 nm to 31.2–63.0 nm. Photoelectrochemical cell study shows that all the CdS films have n-type electrical conductivity. Optical characterization reveals that all samples show similar transmittance and absorbance responses with the transmittance slightly increasing towards higher growth voltages. All the annealed films show energy bandgap of 2.42 eV. Scanning electron microscopy and energy dispersive X-ray analyses show that grains on the surface of the films tend to get cemented together after annealing with prior CdCl2 treatment while all the films are S-rich.

  12. Uranium exploration techniques

    International Nuclear Information System (INIS)

    Nichols, C.E.

    1984-01-01

    The subject is discussed under the headings: introduction (genetic description of some uranium deposits; typical concentrations of uranium in the natural environment); sedimentary host rocks (sandstones; tabular deposits; roll-front deposits; black shales); metamorphic host rocks (exploration techniques); geologic techniques (alteration features in sandstones; favourable features in metamorphic rocks); geophysical techniques (radiometric surveys; surface vehicle methods; airborne methods; input surveys); geochemical techniques (hydrogeochemistry; petrogeochemistry; stream sediment geochemistry; pedogeochemistry; emanometry; biogeochemistry); geochemical model for roll-front deposits; geologic model for vein-like deposits. (U.K.)

  13. Estimating spatial patterns of soil erosion and deposition of the Andean region using geo-information techniques : a case study in Cochabamba, Bolivia

    NARCIS (Netherlands)

    Saavedra, C.

    2005-01-01

    Predicting spatial patterns and intensity of soil erosion and deposition in landscapes is problematic in areas where few experimental data are available. Yet it is in these regions that the ability to extrapolate local field evidence could be most useful for locating the sources of sediments. This

  14. Correlation between physical properties and growth mechanism of In2S3 thin films fabricated by electrodeposition technique with different deposition times

    Science.gov (United States)

    Braiek, Zied; Gannouni, Mounir; Ben Assaker, Ibtissem; Bardaoui, Afrah; Lamouchi, Amina; Brayek, A.; Chtourou, Radhouane

    2015-10-01

    Indium sulfide (In2S3) thin films were grown on ITO-coated glass substrate using the electrodeposition method. The effect of the deposition time on the structural, morphological, optical and electrical properties of the as-grown In2S3 thin films was studied. XRD spectra of the obtained films reveal the polycrystalline nature of (β-In2S3) with a tetragonal crystal structure along the (109) plane, and exhibit a sharp transition to the (0012) plane when the deposition time is extended beyond 20 min. Using atomic force microscope (AFM), the surface morphology shows a remarkable change in the grain size, thickness, and surface roughness when varying the deposition time. UV-VIS spectrophotometer show that the optical band gap values of In2S3 decrease from about 2.82 to 1.93 eV by extending the electrodeposition duration from 5 to 20 min. All films were found to have an n-type character with a lower electrical resistivity of about 1.8×10-3 Ω cm for films deposited at 20 min.

  15. Erosion and sediment deposition evaluation on slopes under different tillage systems in the Cerrado region using the 137Cs fallout technique

    International Nuclear Information System (INIS)

    Arthur, Robson Clayton Jacques

    2010-01-01

    In Brazil, the expansion of agricultural areas causes several problems on natural resources. With the increasing occupation of the Cerrado region by agriculture, a series of environmental problems like deforestation, soil erosion and soil compaction are appearing and causing radical transformations in the natural landscape due to removing almost all native vegetation. The conventional tillage system (CTS) is considered an inadequate form of soil management for its frequently irremediable consequences of soil compaction and soil erosion, and the no till system (NTS) makes the maintenance of the soil conditions possible, letting them close to the natural environment, thus reducing rates of soil erosion. The objective of this work was to evaluate the efficiency of riparian forests in the retention of sediments originated for three different tillage systems, through the fallout 137 CS redistribution technique, the Universal Soil Loss Equation (USLE) and some physical and chemical parameters that indicate the structural conditions of the soils of Goiatuba and Jandaia-GO. In the three areas, soil profiles were collected in three layers of 20 cm (0-20, 20-40 and 40-60 cm) at distinct points located along linear transects in the direction of the maximum slope until the riparian forest. In the riparian forest of each area, trenches were opened and soil was sampled to evaluate the activity of 137 Cs and the physical and chemical parameters of soil. Detection of the activity of 137 Cs was made with a gamma ray detector model (GEM-20180P, EG and ORTEC) connected to a multichannel analyzer. The comparison of averages was made using the Tukey test at 5% level of significance. The. results indicated that, the three soil tillage systems presented high rates of soil erosion and deposition of sediments and the riparian forest of the areas under CTS, NTS and pasture, located downstream received great amounts of sediments, and that only the riparian forest of CTS was capable to trap

  16. Neutron-photon energy deposition in CANDU reactor fuel channels: a comparison of modelling techniques using ANISN and MCNP computer codes

    International Nuclear Information System (INIS)

    Bilanovic, Z.; McCracken, D.R.

    1994-12-01

    In order to assess irradiation-induced corrosion effects, coolant radiolysis and the degradation of the physical properties of reactor materials and components, it is necessary to determine the neutron, photon, and electron energy deposition profiles in the fuel channels of the reactor core. At present, several different computer codes must be used to do this. The most recent, advanced and versatile of these is the latest version of MCNP, which may be capable of replacing all the others. Different codes have different assumptions and different restrictions on the way they can model the core physics and geometry. This report presents the results of ANISN and MCNP models of neutron and photon energy deposition. The results validate the use of MCNP for simplified geometrical modelling of energy deposition by neutrons and photons in the complex geometry of the CANDU reactor fuel channel. Discrete ordinates codes such as ANISN were the benchmark codes used in previous work. The results of calculations using various models are presented, and they show very good agreement for fast-neutron energy deposition. In the case of photon energy deposition, however, some modifications to the modelling procedures had to be incorporated. Problems with the use of reflective boundaries were solved by either including the eight surrounding fuel channels in the model, or using a boundary source at the bounding surface of the problem. Once these modifications were incorporated, consistent results between the computer codes were achieved. Historically, simple annular representations of the core were used, because of the difficulty of doing detailed modelling with older codes. It is demonstrated that modelling by MCNP, using more accurate and more detailed geometry, gives significantly different and improved results. (author). 9 refs., 12 tabs., 20 figs

  17. High throughput, low cost deposition of alumina passivation layers by spatial atomic layer deposition

    NARCIS (Netherlands)

    Vermeer, A.; Roozeboom, F.; Poodt, P.W.G.; Gortzen, R.M.W.

    2012-01-01

    Atomic Layer Deposition (ALD) is a gas phase deposition technique for depositing very high quality thin films with an unsurpassed conformality. The main drawback of ALD however is the very low deposition rate (~ 1 nm/min). Recently, record deposition rates for alumina of up to I nm/s were reached

  18. Tsunami deposits

    International Nuclear Information System (INIS)

    2013-01-01

    The NSC (the Nuclear Safety Commission of Japan) demand to survey on tsunami deposits by use of various technical methods (Dec. 2011), because tsunami deposits have useful information on tsunami activity, tsunami source etc. However, there are no guidelines on tsunami deposit survey in JAPAN. In order to prepare the guideline of tsunami deposits survey and evaluation and to develop the method of tsunami source estimation on the basis of tsunami deposits, JNES carried out the following issues; (1) organizing information of paleoseismological record and tsunami deposit by literature research, (2) field survey on tsunami deposit, and (3) designing the analysis code of sediment transport due to tsunami. As to (1), we organize the information gained about tsunami deposits in the database. As to (2), we consolidate methods for surveying and identifying tsunami deposits in the lake based on results of the field survey in Fukui Pref., carried out by JNES. In addition, as to (3), we design the experimental instrument for hydraulic experiment on sediment transport and sedimentation due to tsunamis. These results are reflected in the guideline on the tsunami deposits survey and evaluation. (author)

  19. Correlation of iron deposition and change of gliocyte metabolism in the basal ganglia region evaluated using magnetic resonance imaging techniques: an in vivo study

    OpenAIRE

    Liu, Haodi; Wang, Xiaoming

    2016-01-01

    Introduction We assessed the correlation between iron deposition and the change of gliocyte metabolism in healthy subjects? basal ganglia region, by using 3D-enhanced susceptibility weighted angiography (ESWAN) and proton magnetic resonance spectroscopy (1H-MRS). Material and methods Seventy-seven healthy volunteers (39 female and 38 male subjects; age range: 24?82 years old) were enrolled in the experiment including ESWAN and proton MRS sequences, consent for which was provided by themselves...

  20. Structural properties and surface wettability of Cu-containing diamond-like carbon films prepared by a hybrid linear ion beam deposition technique

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Peng; Sun, Lili; Li, Xiaowei [Key Laboratory of Marine Materials and Related Technologies, Zhejiang Key Laboratory of Marine Materials and Protective Technologies, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China); Xu, Sheng [Gao Hong Coating Technology Co., Ltd, Huzhou 313000 (China); Ke, Peiling [Key Laboratory of Marine Materials and Related Technologies, Zhejiang Key Laboratory of Marine Materials and Protective Technologies, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China); Wang, Aiying, E-mail: aywang@nimte.ac.cn [Key Laboratory of Marine Materials and Related Technologies, Zhejiang Key Laboratory of Marine Materials and Protective Technologies, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China)

    2015-06-01

    Cu-containing diamond-like carbon (Cu-DLC) films were deposited on Si/glass substrate by a hybrid ion beam deposition system. The Cu concentration (0.1–39.7 at.%) in the film was controlled by varying the sputtering current. The microstructure and composition of Cu-DLC films were investigated systematically. The surface topography, roughness and surface wettability of the films were also studied. Results indicated that with increasing the Cu concentration, the water contact angle of the films changed from 66.8° for pure carbon film to more than 104.4° for Cu-DLC films with Cu concentration larger than 24.4 at.%. In the hydrophilic region, the polar surface energy decreased from 30.54 mJ/m{sup 2} for pure carbon film to 2.48 mJ/m{sup 2} for the film with Cu 7.0 at.%. - Highlights: • Cu-containing diamond-like carbon (DLC) films were deposited by a hybrid ion beam system. • Cu-containing DLC films exhibited a wide range of water contact angle. • The water contact angles vary with the surface energies and surface roughness.

  1. Correlation of iron deposition and change of gliocyte metabolism in the basal ganglia region evaluated using magnetic resonance imaging techniques: an in vivo study.

    Science.gov (United States)

    Liu, Haodi; Wang, Xiaoming

    2016-02-01

    We assessed the correlation between iron deposition and the change of gliocyte metabolism in healthy subjects' basal ganglia region, by using 3D-enhanced susceptibility weighted angiography (ESWAN) and proton magnetic resonance spectroscopy ((1)H-MRS). Seventy-seven healthy volunteers (39 female and 38 male subjects; age range: 24-82 years old) were enrolled in the experiment including ESWAN and proton MRS sequences, consent for which was provided by themselves or their guardians. For each subject, the mean phase value gained by ESWAN was used to evaluate the iron deposition; choline/creatine (Cho/Cr) and mI/Cr ratios gained by (1)H-MRS were used to evaluate gliocyte metabolism in the basal ganglia region of both sides. The paired t test was used to test the difference between the two sides of the basal ganglia region. Linear regression was performed to evaluate the relation between mean phase value and age. Pearson's correlation coefficient was calculated to analyze the relationship between the result of ESWAN and (1)H-MRS. There was no difference between the two sides of the basal ganglia region in the mean phase value and Cho/Cr. But in mI/Cr the mean phase value of each nucleus in bilateral basal ganglia decreased with increasing age. There are 16 r-values between the mean phase value and Cho/Cr and mI/Cr in bilateral basal ganglia region. And each of all p-values is less than 0.001 (p basal ganglia is associated with the change of gliocyte metabolism with increasing age. Iron deposition in each nucleus of the basal ganglia region changes with age.

  2. Synthesis highly active platinum tri-metallic electrocatalysts using 'one-step' organometallic chemical vapour deposition technique for methanol oxidation process

    International Nuclear Information System (INIS)

    Naidoo, Qi-Ling; Petrik, Leslie; Nechaev, Alexander; Naidoo, Sivapregasen; Ndungu, Patrick; Vaivars, Guntars

    2012-01-01

    A simple solvent free method for the synthesis of tri-metallic platinum electrocatalysts on carbon nanotubes is presented. By investigating the platinum alloy electrocatalysts, it was showed that the additional metals of platinum alloys could reduce the metal particle sizes and produce larger chemical-active surface area, as well as the higher methanol oxidation activity of the catalysts. The organometallic chemical vapour deposition method was successfully applied to produce multiple samples of PtRuFe, PtRuCu and PtRuV. The electrocatalysts were characterized by ICP, XRD, HRTEM and the catalytic activity was determined by cyclic voltammetry (CV).

  3. Application of the PDMPO technique in studying silica deposition in natural populations of .i.Fragilaria crotonensis./i. (Bacillariophyceae) at different depths in a eutrophic reservoir

    Czech Academy of Sciences Publication Activity Database

    Znachor, Petr; Nedoma, Jiří

    2008-01-01

    Roč. 44, č. 2 (2008), s. 518-525 ISSN 0022-3646 R&D Projects: GA ČR(CZ) GA206/05/0007; GA ČR(CZ) GA206/06/0462; GA AV ČR(CZ) IAA600170602; GA AV ČR(CZ) 1QS600170504 Institutional research plan: CEZ:AV0Z60170517 Keywords : PDMPO * diatoms * Si deposition * image analysis * fluorescence Subject RIV: DA - Hydrology ; Limnology Impact factor: 2.811, year: 2008

  4. Directed vapor deposition

    Science.gov (United States)

    Groves, James Frederick

    This dissertation describes the invention, design, construction, experimental evaluation and modeling of a new physical vapor deposition technique (U.S. Patent #5,534,314) for high rate, efficient deposition of refractory elements, alloys, and compounds onto flat or curved surfaces. The new Directed Vapor Deposition (DVD) technique examined in this dissertation was distinct from previous physical vapor deposition techniques because it used low vacuum electron beam (e-beam) evaporation in combination with a carrier gas stream to transport and vapor spray deposit metals, ceramics, and semiconducting materials. Because of the system's unique approach to vapor phase materials processing, detailed analyses of critical concepts (e.g. the e-beam accelerating voltage and power required for evaporation, the vacuum pumping capacity necessary to generate specific gas flow velocities exiting a nozzle) were used to reduce to practice a functioning materials synthesis tool. After construction, the ability to create low contamination films of pure metals, semi-conducting materials, and compounds via this new method was demonstrated, and oxide deposition using an oxygen-doped gas stream in combination with a pure metal evaporant source was shown to be feasible. DVD vapor transport characteristics were experimentally investigated with deposition chamber pressure, carrier gas type, and e-beam power being identified as major processing parameters which affected vapor atom trajectories. The low vacuum carrier gas streams employed in DVD showed a dramatic ability to focus the vapor stream during transport to the substrate and thereby enhance material deposition rates and efficiencies significantly under certain process conditions. Conditions for maximum deposition efficiency onto flat substrates and continuous fibers were experimentally identified by varying chamber pressure, carrier gas velocity (Mach number), and e-beam power. Deposition efficiencies peaked at about 0.5 Torr when

  5. Laboratory Deposition Apparatus to Study the Effects of Wax Deposition on Pipe Magnetic Field Leakage Signals

    Directory of Open Access Journals (Sweden)

    Karim Mohd Fauzi Abd

    2014-07-01

    Full Text Available Accurate technique for wax deposition detection and severity measurement on cold pipe wall is important for pipeline cleaning program. Usually these techniques are validated by conventional techniques on laboratory scale wax deposition flow loop. However conventional techniques inherent limitations and it is difficult to reproduce a predetermine wax deposit profile and hardness at designated location in flow loop. An alternative wax deposition system which integrates modified pour casting method and cold finger method is presented. This system is suitable to reproduce high volume of medium hard wax deposit in pipe with better control of wax deposit profile and hardness.

  6. Twin-cuvette measurement technique for investigation of dry deposition of O3 and PAN to plant leaves under controlled humidity conditions

    Directory of Open Access Journals (Sweden)

    S. Sun

    2016-02-01

    with Quercus ilex was investigated over a 14 day measurement period under controlled climate chamber conditions. By using O3 mixing ratios between 32 and 105 ppb and PAN mixing ratios between 100 and 350 ppt, a linear dependency of the O3 flux as well as the PAN flux in relation to its ambient mixing ratio could be observed. At relative humidity (RH of 40 %, the deposition velocity ratio of O3 and PAN was determined to be 0.45. At that humidity, the deposition of O3 to the plant leaves was found to be only controlled by the leaf stomata. For PAN, an additional resistance inhibited the uptake of PAN by the leaves. Furthermore, the formation of water films on the leaf surface of plants inside the chamber could be continuously tracked with our custom built leaf wetness sensors. Using this modified leaf wetness sensor measuring the electrical surface conductance on the leaves, an exponential relationship between the ambient humidity and the electrical surface conductance could be determined.

  7. Noninvasive radioisotopic technique for detection of platelet deposition on bovine pericardial mitral-valve prosthesis and in vitro quantification of visceral microembolism in dogs

    International Nuclear Information System (INIS)

    Dewanjee, M.K.; Trastek, V.F.; Tago, M.; Torianni, M.; Kaye, M.P.

    1983-01-01

    Platelet deposition on bovine pericardial-tissue mitral-valve prostheses in dogs was observed noninvasively by use of 111 In-labeled platelets and quantified after sacrifice at one, 14 and 30 days postimplantation (300-400 microCi of labeled platelets having been injected 24 hrs previously). Thrombosis on the sewing ring and pericardial leaflets at one and 14 days and on the leaflets at 30 days was delineated in scintiphotos. In vitro quantification (% injected dose) indicated that the sewing ring and perivalvular tissue retained 0.75% of labeled platelets at one day postimplantation, 0.084% at 14 days, and 0.0042% at 30 days. Platelet survival was reduced to 38 hrs at 21 days postimplantation but returned toward the normal (50 hrs) with endothelial covering of the sewing ring. Microemboli in lung and kidney, as measured by tissue/blood radioactivity ratio, decreased significantly at 30 days. 111 In-labeled platelets thus provide a sensitive marker for noninvasive imaging and in vitro quantification of platelet deposition on valvular prostheses and microemboli trapped in viscera

  8. Fabrication of highly conductive Ta-doped SnO{sub 2} polycrystalline films on glass using seed-layer technique by pulse laser deposition

    Energy Technology Data Exchange (ETDEWEB)

    Nakao, Shoichiro, E-mail: tg-s-nakao@newkast.or.j [Kanagawa Academy of Science and Technology (KAST), Kawasaki 213-0012 (Japan); Department of Chemistry, University of Tokyo, Tokyo 113-0033 (Japan); Yamada, Naoomi [Kanagawa Academy of Science and Technology (KAST), Kawasaki 213-0012 (Japan); Hitosugi, Taro [Kanagawa Academy of Science and Technology (KAST), Kawasaki 213-0012 (Japan); Advanced Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan); Hirose, Yasushi; Shimada, Toshihiro; Hasegawa, Tetsuya [Kanagawa Academy of Science and Technology (KAST), Kawasaki 213-0012 (Japan); Department of Chemistry, University of Tokyo, Tokyo 113-0033 (Japan)

    2010-03-31

    We discuss the fabrication of highly conductive Ta-doped SnO{sub 2} (Sn{sub 1-x}Ta{sub x}O{sub 2}; TTO) thin films on glass by pulse laser deposition. On the basis of the comparison of X-ray diffraction patterns and resistivity ({rho}) values between epitaxial films and polycrystalline films deposited on bare glass, we proposed the use of seed-layers for improving the conductivity of the TTO polycrystalline films. We investigated the use of rutile TiO{sub 2} and NbO{sub 2} as seed-layers; these are isostructural materials of SnO{sub 2,} which are expected to promote epitaxial-like growth of the TTO films. The films prepared on the 10-nm-thick seed-layers exhibited preferential growth of the TTO (110) plane. The TTO film with x = 0.05 on rutile TiO{sub 2} exhibited {rho} = 3.5 x 10{sup -4} {Omega} cm, which is similar to those of the epitaxial films grown on Al{sub 2}O{sub 3} (0001).

  9. Effects of the precursor concentration and different annealing ambients on the structural, optical, and electrical properties of nanostructured V2O5 thin films deposited by spray pyrolysis technique

    Science.gov (United States)

    Irani, Rowshanak; Rozati, Seyed Mohammad; Beke, Szabolcs

    2018-04-01

    V2O5 thin films were deposited with different precursor concentrations of 0.01, 0.05, and 0.1 M on glass substrates by spray pyrolysis technique, then the optimized films were annealed in different ambients (air, oxygen, and vacuum). The results showed that by increasing the concentration, the films grew along the (001) direction with an orthorhombic structure. Field emission scanning electron microscopy showed that nanorods were formed when depositing 0.05 molar of VCl3. We conclude that with the precursor concentration, the surface nanostructure can be well-controlled. Annealing improved the crystallinity under all ambients, but the best crystallinity was achieved in vacuum. It was revealed that the as-deposited films had the highest transmission, whereas the films annealed in air had the lowest. When annealed in air, the optical band gap decreased from 2.45 to 2.32 eV. The sheet resistance, resistivity, mobility, conductivity, and carrier concentration were measured for all the prepared V2O5 films.

  10. Deposit of thin films of nitrided amorphous carbon using the laser ablation technique; Deposito de peliculas delgadas de carbono amorfo nitrurado utilizando la tecnica de ablacion laser

    Energy Technology Data Exchange (ETDEWEB)

    Rebollo, P.B.; Escobar A, L.; Camps C, E. [Departamento de Fisica, Instituto Nacional de Investigaciones Nucleares, C.P. 52045 Salazar, Estado de Mexico (Mexico); Haro P, E.; Camacho L, M.A. [Departamento de Fisica, Universidad Autonoma Metropolitana Iztapalapa (Mexico); Muhl S, S. [Instituto de Investigacion en Materiales, UNAM (Mexico)

    2000-07-01

    It is reported the synthesis and characterization of thin films of amorphous carbon (a-C) nitrided, deposited by laser ablation in a nitrogen atmosphere at pressures which are from 4.5 x 10 {sup -4} Torr until 7.5 x 10 {sup -2} Torr. The structural properties of the films are studied by Raman spectroscopy obtaining similar spectra at the reported for carbon films type diamond. The study of behavior of the energy gap and the ratio nitrogen/carbon (N/C) in the films, shows that the energy gap is reduced when the nitrogen incorporation is increased. It is showed that the refraction index of the thin films diminish as nitrogen pressure is increased, indicating the formation of graphitic material. (Author)

  11. Structural and Electrical Properties of Ag/ n-TiO2/ p-Si/Al Heterostructure Fabricated by Pulsed Laser Deposition Technique

    Science.gov (United States)

    Kumar, Arvind; Sharma, K. K.; Kumar, Rajender; Chand, Subhash; Kumar, Ashwani

    2017-11-01

    We have investigated the structural and electrical characteristics of the Ag/ n-TiO2/ p-Si/Al heterostructure. Thin films of pure TiO2 were deposited on p-type silicon (100) by optimized pulsed laser ablation with a KrF-excimer laser in an oxygen-controlled environment. X-ray diffraction analysis showed the formation of crystalline TiO2 film having a tetragonal texture with a strong (210) plane as the preferred direction. High purity aluminium and silver metals were deposited to obtain ohmic contacts on p-Si and n-TiO2, respectively. The current-voltage ( I- V) characteristics of the fabricated heterostructure were studied by using thermionic emission diffusion mechanism over the temperature range of 80-300 K. Parameters such as barrier height and ideality factor were derived from the measured I- V data of the heterostructure. The detailed analysis of I- V measurements revealed good rectifying behavior in the inhomogeneous Ag/ n-TiO2/ p-Si(100)/Al heterostructure. The variations of barrier height and ideality factor with temperature and the non-linearity of the activation energy plot confirmed that barrier heights at the interface follow Gaussian distributions. The value of Richardson's constant was found to be 6.73 × 105 Am-2 K-2, which is of the order of the theoretical value 3.2 × 105 Am-2 K-2. The capacitance-voltage ( C- V) measurements of the heterostructure were investigated as a function of temperature. The frequency dependence (Mott-Schottky plot) of the C- V characteristics was also studied. These measurements indicate the occurrence of a built-in barrier and impurity concentration in TiO2 film. The optical studies were also performed using a UV-Vis spectrophotometer. The optical band gap energy of TiO2 films was found to be 3.60 eV.

  12. Carbon thin films deposited by the magnetron sputtering technique using cobalt, copper and nickel as buffer-layers; Filmes finos de carbono depositados por meio da tecnica de magnetron sputtering usando cobalto, cobre e niquel como buffer-layers

    Energy Technology Data Exchange (ETDEWEB)

    Costa e Silva, Danilo Lopes

    2015-11-01

    In this work, carbon thin films were produced by the magnetron sputtering technique using single crystal substrates of alumina c-plane (0001) and Si (111) and Si (100) substrates, employing Co, Ni and Cu as intermediate films (buffer-layers). The depositions were conducted in three stages, first with cobalt buffer-layers where only after the production of a large number of samples, the depositions using cooper buffer-layers were carried out on Si substrates. Then, depositions were performed with nickel buffer layers using single-crystal alumina substrates. The crystallinity of the carbon films was evaluated by using the technique of Raman spectroscopy and, then, by X-ray diffraction (XRD). The morphological characterization of the films was performed by scanning electron microscopy (SEM and FEG-SEM) and high-resolution transmission electron microscopy (HRTEM). The XRD peaks related to the carbon films were observed only in the results of the samples with cobalt and nickel buffer-layers. The Raman spectroscopy showed that the carbon films with the best degree of crystallinity were the ones produced with Si (111) substrates, for the Cu buffers, and sapphire substrates for the Ni and Co buffers, where the latter resulted in a sample with the best crystallinity of all the ones produced in this work. It was observed that the cobalt has low recovering over the alumina substrates when compared to the nickel. Sorption tests of Ce ions by the carbon films were conducted in two samples and it was observed that the sorption did not occur probably because of the low crystallinity of the carbon films in both samples. (author)

  13. Optical and structural properties of nanostructured ZnO thin films deposited onto FTO/glass substrate by a solution-based technique

    CSIR Research Space (South Africa)

    Berruet, M

    2013-10-01

    Full Text Available Nanostructured zinc oxide thin films were spin coated on conductive glass substrates via a sol–gel based technique using zinc acetate dihydrate as precursor. The pH of the alkalis used as catalytic agents in the hydrolysis step is shown to have a...

  14. Liquefier Dynamics in Fused Deposition

    DEFF Research Database (Denmark)

    Bellini, Anna; Guceri, Selcuk; Bertoldi, Maurizio

    2004-01-01

    Layered manufacturing (LM) is an evolution of rapid prototyping (RP) technology whereby a part is built in layers. Fused deposition modeling (FDM) is a particular LM technique in which each section is fabricated through vector style deposition of building blocks, called roads, which...

  15. Impact of surface morphology of Si substrate on performance of Si/ZnO heterojunction devices grown by atomic layer deposition technique

    International Nuclear Information System (INIS)

    Hazra, Purnima; Singh, Satyendra Kumar; Jit, Satyabrata

    2015-01-01

    In this paper, the authors have investigated the structural, optical, and electrical characteristics of silicon nanowire (SiNW)/zinc oxide (ZnO) core–shell nanostructure heterojunctions and compared their characteristics with Si/ZnO planar heterojunctions to investigate the effect of surface morphology of Si substrate in the characteristics of Si/ZnO heterojunction devices. In this work, ZnO thin film was conformally deposited on both p-type 〈100〉 planar Si substrate and substrate with vertically aligned SiNW arrays by atomic layer deposition (ALD) method. The x-ray diffraction spectra show that the crystalline structures of Si/ZnO heterojunctions are having (101) preferred orientation, whereas vertically oriented SiNW/ZnO core–shell heterojunctions are having (002)-oriented wurtzite crystalline structures. The photoluminescence (PL) spectra of Si/ZnO heterojunctions show a very sharp single peak at 377 nm, corresponding to the bandgap of ZnO material with no other defect peaks in visible region; hence, these devices can have applications only in UV region. On the other hand, SiNW/ZnO heterojunctions are having band-edge peak at 378 nm along with a broad emission band, spreading almost throughout the entire visible region with a peak around 550 nm. Therefore, ALD-grown SiNW/ZnO heterojunctions can emit green and red light simultaneously. Reflectivity measurement of the heterojunctions further confirms the enhancement of visible region peak in the PL spectra of SiNW/ZnO heterojunctions, as the surface of the SiNW/ZnO heterojunctions exhibits extremely low reflectance ( 20%). The current–voltage characteristics of both Si/ZnO and SiNW/ZnO heterojunctions are measured with large area ohmic contacts on top and bottom of the structure to compare the electrical characteristics of the devices. Due to large surface to-volume ratio of SiNW/ZnO core–shell heterojunction devices, the output current rating is about 130 times larger compared to their planar

  16. Effect of discharge current and deposition temperature on roughness and density of NbC films fabricated by ion beam sputtering technique

    Science.gov (United States)

    Dhawan, Rajnish; Rai, Sanjay; Lodha, G. S.

    2014-04-01

    NbC films were prepared using Ion beam sputtering system at various discharges current from 0.4 amps to 1.2 amps at room temperature. Effect of temperature on NbC films were also studied by depositing NbC films at various temperatures from room temperature to 200,300,400 and 600°C. X-ray reflectivity (XRR) study shows that surface roughness of the film decreases with decrease in discharge current. The optimum lowest roughness 3.2´̊A having density 92% of bulk was achieved at discharge current 0.6 amps at 3.0 cm3/min Ar gas flow. X-ray study also shows that film roughness decreases with increase in temperature of the film and after a certain temperature it increases with increase in temperature. The lowest surface roughness 2.1´̊A was achieved at 300°C with density 83% of bulk NbC at constant discharge current 0.6 amps.

  17. Development of Calibration-Free Laser-Induced-Breakdown-Spectroscopy based techniques for deposited layers diagnostics on ITER-like tiles

    Science.gov (United States)

    Fantoni, Roberta; Almaviva, Salvatore; Caneve, Luisa; Colao, Francesco; Popov, Andrey M.; Maddaluno, Giorgio

    2013-09-01

    High temperature plasma in hydrogen isotopes is peculiar of thermonuclear fusion devices. The study of plasma-wall interaction is of paramount importance for avoiding both damage of plasma facing components (PFCs) and pollution of the plasma. To assure continuous and fault-free operation a strict control must be exerted on the amount of impurities deposited on, and of the fuel retained in the PFCs. This requirement makes Laser-Induced-Breakdown-Spectroscopy (LIBS) an ideal candidate for on-line quantitative monitoring of the walls of the current as well as of the next generation fusion devices like the International Thermonuclear Experimental Reactor (ITER). An experimental setup has been designed and realized in order to optimize the characteristics of a LIBS system working at low pressure and remotely, and it has been utilized in combination with calibration free procedures for quantitative analysis. In this work, a partial calibration free method has been developed for single shot analysis of hydrogen isotopes retention at the PFCs-like surfaces, based on the acquisition of high resolution spectra in a narrow wavelength range. Results of calibration free and partial calibration free have been obtained on suitably deuterated samples; preliminary spectroscopic considerations on tritium detection are also presented.

  18. Assessment of atmospheric deposition of heavy metals and other elements in Belgrade using the moss biomonitoring technique and neutron activation analysis

    International Nuclear Information System (INIS)

    Anicic, M.; Tomasevic, M.; Frontas'eva, M.V.; Popovic, A.

    2006-01-01

    The study aimed at assessing atmospheric deposition of heavy metals and other elements using the moss genera Brachythecium sp. (B. rutabulum and B. salebrosum) and Eurhynchium sp. (E. hians and E. striatum) collected in autumn 2004 in the urban area of Belgrade. The concentrations of 36 elements (Na, Mg, Al, Cl, K, Ca, Sc, Ti, V, Cr, Mn, Fe, Co, Ni, Zn, As, Se, Br, Rb, Sr, Mo, Sb, I, Cs, Ba, La, Ce, Sm, Tb, Dy, Hf, Ta, W, Hg, Th, U) were determined in moss and local topsoil samples by instrumental neutron activation analysis. The concentration of elements in moss positively correlated to those obtained for topsoil. High enrichment factors for As, Zn, Mo, Br, Sb, Se, Hg, and Cl, calculated to continental crust composition, gave an evidence for anthropogenic impact on urban area, mainly due to intensive vehicular traffic and fossil fuel combustion. The concentrations of elements in moss, characteristic for fossil fuel combustion, obtained in this study, were substantially lower than in the previous investigation (2000) conducted in the area of Belgrade. The level of concentrations for V, Cr, Ni, and As in moss from this study correlated to those measured for neighboring countries, and were several times higher than the base-level data from low polluted areas. The level of accumulated elements in both investigated moss genera were similar and all studied species could be combined for biomonitoring purposes in urban areas

  19. A Heavy Metal Atmospheric Deposition Study Around the Lead and Copper-Zinc Smelters in Baia Mare, Romania, Employing the Moss Biomonitoring Technique, ENAA and FAAS

    CERN Document Server

    Culicov, O A; Steinnes, E; Okina, O S; Santa, Z; Todoran, R

    2001-01-01

    The mosses Pleurozium schreberi, Pseudoscleropodium purum and Rhytidiadelphus squarrosus were used as biomonitors to study the atmospheric deposition of metals around the lead and copper-zinc smelters in Baia Mare. Samples representing the last three years' growth of moss or its green part, collected on the ground at 28 sites located 2-20 km from the source area, were analyzed by instrumental neutron activation analysis using epithermal neutrons (ENAA) and by flame atomic absorption spectrometry (FAAS). A total of 30 elements were determined, including most of the heavy metals known to be released into the air from this kind of industry. Obtained concentrations for As and Cu are comparable with those observed in Karabash, South Ural Mountains, one of the most polluted regions in Europe. Besides, these two elements correlate very well with each other. The mean values for Zn (136 ppm) and Pb (41 ppm) are substantially higher than those normally found in the literature. The highest value for Pb (175 ppm) was obs...

  20. UNA REVISIÓN DEL SPRAY TÉRMICO COMO TÉCNICA DE DEPOSICIÓN PARA CAPAS DE BARRERAS TÉRMICAS // THE THERMAL SPRAY AS A DEPOSITION TECHNIQUE FOR THERMAL BARRIER COATING: A REVIEW

    Directory of Open Access Journals (Sweden)

    Eduardo Rondón Briceño

    2015-06-01

    Full Text Available It is important to know the thermal barrier deposition techniques since materials with low thermal conductivity in the barrier can be obtained from them. The dependence of the thermal conductivity with the temperature can be divided into four regions. In this work, we were interested in the study of used techniques for the manufacture of materials with a desirable low thermal conductivity that will be exposed to high temperatures that is to say, materials found in the III and IV region. In these regions the thermal conductivity can be reduced increasing the porosity of the material. Through the study of the thermal barrier deposition techniques we found that the thermal spray produces a coat with high porosity, being the low velocity flame spray technique the best to produce coat of La2Zr2O7 with a minimal thermal conductivity. The thermal spray technique is low cost and almost any material can be thermally sprayed, so this can be considered a very attractive technique for industrial applications. // RESUMEN Es importante conocer las técnicas de deposición de barreras térmicas ya que de ellas depende la obtención de materiales con baja conductividad térmica en la barrera. La dependencia de la conductividad térmica con la temperatura puede dividirse en cuatro regiones. En este trabajo estuvimos interesados en el estudio de las técnicas que se utilizan para la fabricación de materiales sometidos a muy altas temperaturas y donde se desea que su conductividad térmica sea baja, es decir, materiales que se encuentran en la región III y IV. En estas regiones se puede disminuir la conductividad térmica aumentando la porosidad del material. A través del estudio de las técnicas de deposición de barreras térmica, hemos encontrado que la técnica del spray térmico produce una alta porosidad en el recubrimiento, siendo el método de rociado con baja velocidad el mejor método para producir capas de La2Zr2O7 con mínima conductividad t

  1. Optical thin film deposition

    International Nuclear Information System (INIS)

    Macleod, H.A.

    1979-01-01

    The potential usefulness in the production of optical thin-film coatings of some of the processes for thin film deposition which can be classified under the heading of ion-assisted techniques is examined. Thermal evaporation is the process which is virtually universally used for this purpose and which has been developed to a stage where performance is in almost all respects high. Areas where further improvements would be of value, and the possibility that ion-assisted deposition might lead to such improvements, are discussed. (author)

  2. Growth of superconducting Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub 8+{delta}} films by sedimentation deposition and liquid phase sintering and annealing technique

    Energy Technology Data Exchange (ETDEWEB)

    Manahan, R.L.C. [Condensed Matter Physics Laboratory, National Institute of Physics, University of the Philippines, Llamas Science Hall, Rm. 3122, E. Quirino Street, Diliman, Quezon City 1101 (Philippines)]. E-mail: rcmanahan@nip.upd.edu.ph; Sarmago, R.V. [Condensed Matter Physics Laboratory, National Institute of Physics, University of the Philippines, Llamas Science Hall, Rm. 3122, E. Quirino Street, Diliman, Quezon City 1101 (Philippines)

    2006-10-01

    We report on a technique of growing highly c-axis oriented Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub 8+{delta}} (Bi-2212) thick films on MgO substrate using a combined sedimentation-deposition and liquid phase sintering and annealing process. The temperature profiles employed partial melting followed by rapid cooling to temperature below the melting point. Scanning electron micrographs show that the films have a smooth surface. No evidence of grain boundaries on the film's surface can be seen. The critical temperatures of the samples range from {approx}67 K to {approx}81 K. This method presents a quick and easy preparation for high quality epitaxial Bi-2212 films.

  3. Infiltration deposits

    International Nuclear Information System (INIS)

    Khasanov, A.Kh.

    1988-01-01

    Infiltration deposits-is concentration of minerals matters formed by concretion on the some depth of readily soluble of descending waters of hyper genes zone. In the process of rocks chemical decomposition a great deal of readily soluble components in the form of sulfates, carbonates, bicarbonates, hydro-oxides and complex compounds, including ore element compounds become free

  4. Comparison between two sampling methods by results obtained using petrographic techniques, specially developed for minerals of the Itataia uranium phosphate deposit, Ceara, Brazil

    International Nuclear Information System (INIS)

    Salas, H.T.; Murta, R.L.L.

    1985-01-01

    The results of comparison of two sampling methods applied to a gallery of the uranium-phosphate ore body of Itataia-Ceara State, Brazil, along 235 metres of mineralized zone, are presented. The results were obtained through petrographic techniques especially developed and applied to both samplings. In the first one it was studied hand samples from a systematically sampling made at intervals of 2 metres. After that, the estimated mineralogical composition studies were carried out. Some petrogenetic observations were for the first time verified. The second sampling was made at intervals of 20 metres and 570 tons of ore extracted and distributed in sections and a sample representing each section was studied after crushing at -65. Their mineralogy were quantified and the degree of liberation of apatite calculated. Based on the mineralogical data obtained it was possible to represent both samplings and to make the comparison of the main mineralogical groups (phosphates, carbonates and silicates). In spite of utilizing different methods and methodology and the kind of mineralization, stockwork, being quite irregular, the results were satisfactory. (Author) [pt

  5. Production of BiPbSrCaCuO thin films on MgO and Ag/MgO substrates by electron beam deposition techniques

    CERN Document Server

    Varilci, A; Gorur, O; Celebi, S; Karaca, I

    2002-01-01

    Superconducting BiPbSrCaCuO thin films were prepared on MgO(001) and Ag/MgO substrates using an electron beam (e-beam) evaporation technique. The effects of annealing temperature and Ag diffusion on the crystalline structure and some superconducting properties, respectively, were investigated by X-ray diffraction, atomic force microscopy, and by measurements of the critical temperature and the critical current density. It was shown that an annealing of both types of films at 845 or 860 C resulted in the formation of mixed Bi-2223 and Bi-2212 phases with a high degree of preferential orientation with the c-axis perpendicular to the substrates. The slight increase of the critical temperature from 103 K to 105 K, the enhancement of the critical current density from 2 x 10 sup 3 to 6 x 10 sup 4 A/cm sup 2 , and the improved surface smoothness are due to a possible silver doping from the substrate. (Abstract Copyright [2002], Wiley Periodicals, Inc.)

  6. Inkjet deposited circuit components

    Science.gov (United States)

    Bidoki, S. M.; Nouri, J.; Heidari, A. A.

    2010-05-01

    All-printed electronics as a means of achieving ultra-low-cost electronic circuits has attracted great interest in recent years. Inkjet printing is one of the most promising techniques by which the circuit components can be ultimately drawn (i.e. printed) onto the substrate in one step. Here, the inkjet printing technique was used to chemically deposit silver nanoparticles (10-200 nm) simply by ejection of silver nitrate and reducing solutions onto different substrates such as paper, PET plastic film and textile fabrics. The silver patterns were tested for their functionality to work as circuit components like conductor, resistor, capacitor and inductor. Different levels of conductivity were achieved simply by changing the printing sequence, inks ratio and concentration. The highest level of conductivity achieved by an office thermal inkjet printer (300 dpi) was 5.54 × 105 S m-1 on paper. Inkjet deposited capacitors could exhibit a capacitance of more than 1.5 nF (parallel plate 45 × 45 mm2) and induction coils displayed an inductance of around 400 µH (planar coil 10 cm in diameter). Comparison of electronic performance of inkjet deposited components to the performance of conventionally etched items makes the technique highly promising for fabricating different printed electronic devices.

  7. Electrophoretic deposition of biomaterials

    Science.gov (United States)

    Boccaccini, A. R.; Keim, S.; Ma, R.; Li, Y.; Zhitomirsky, I.

    2010-01-01

    Electrophoretic deposition (EPD) is attracting increasing attention as an effective technique for the processing of biomaterials, specifically bioactive coatings and biomedical nanostructures. The well-known advantages of EPD for the production of a wide range of microstructures and nanostructures as well as unique and complex material combinations are being exploited, starting from well-dispersed suspensions of biomaterials in particulate form (microsized and nanoscale particles, nanotubes, nanoplatelets). EPD of biological entities such as enzymes, bacteria and cells is also being investigated. The review presents a comprehensive summary and discussion of relevant recent work on EPD describing the specific application of the technique in the processing of several biomaterials, focusing on (i) conventional bioactive (inorganic) coatings, e.g. hydroxyapatite or bioactive glass coatings on orthopaedic implants, and (ii) biomedical nanostructures, including biopolymer–ceramic nanocomposites, carbon nanotube coatings, tissue engineering scaffolds, deposition of proteins and other biological entities for sensors and advanced functional coatings. It is the intention to inform the reader on how EPD has become an important tool in advanced biomaterials processing, as a convenient alternative to conventional methods, and to present the potential of the technique to manipulate and control the deposition of a range of nanomaterials of interest in the biomedical and biotechnology fields. PMID:20504802

  8. Tandem solar cells deposited using hot-wire chemical vapor deposition

    NARCIS (Netherlands)

    Veen, M.K. van

    2003-01-01

    In this thesis, the application of the hot-wire chemical vapor deposition (HWCVD) technique for the deposition of silicon thin films is described. The HWCVD technique is based on the dissociation of silicon-containing gasses at the catalytic surface of a hot filament. Advantages of this technique

  9. Étude de la technique d'échange ionique avec compétition. Cas du dépôt de platine sur support solide acide par échange cationique Research on the Ion Exchange Technique with Competition. Case of Platinum Deposit on a Solid Acid Support by Cation Exchange

    Directory of Open Access Journals (Sweden)

    Ribeiro F.

    2006-11-01

    Full Text Available Cet article présente une étude détaillée de la technique de dépôt de platine sur support acide par échange cationique avec compétition. Cette technique permet d'obtenir à la fois une dispersion quasi atomique et une répartition macroscopique homogène du métal sur la surface du solide. En l'absence de limitations diffusionnelles extra-granulaires, les résultats expérimentaux sont en bon accord avec les prévisions théoriques . This article is a detailed examination of the technique of depositing platinum on an acid support by cation exchange with compétition. This technique produces both a quasi-atomic dispersion and a homogeneous macroscopic distribution of the métal onthe surface of the solid. In the absence of extragranular diffusion limitations, experimental findings are in good agreement with theoretical predictions.

  10. Plasmon-assisted chemical vapor deposition.

    Science.gov (United States)

    Boyd, David A; Greengard, Leslie; Brongersma, Mark; El-Naggar, Mohamed Y; Goodwin, David G

    2006-11-01

    We introduce a new chemical vapor deposition (CVD) process that can be used to selectively deposit materials of many different types. The technique makes use of the plasmon resonance in nanoscale metal structures to produce the local heating necessary to initiate deposition when illuminated by a focused low-power laser. We demonstrate the technique, which we refer to as plasmon-assisted CVD (PACVD), by patterning the spatial deposition of PbO and TiO(2) on glass substrates coated with a dispersion of 23 nm gold particles. The morphology of both oxide deposits is consistent with local laser-induced heating of the gold particles by more than 150 degrees C. We show that temperature changes of this magnitude are consistent with our analysis of the heat-loss mechanisms. The technique is general and can be used to spatially control the deposition of virtually any material for which a CVD process exists.

  11. Influence of Annealing Temperature on Some Optical and Structural Properties of Cu2ZnSnS4 Deposited by CZT Co-Electrodeposition Coupled with Chemical Bath Technique

    Science.gov (United States)

    Okoth, Obila Jorim; Domtau, Dinfa Luka; Marina, Mukabi; John, Onyatta; Awuor, Ogacho Alex

    Copper indium gallium selenide (CIGS) is currently most efficient thin film solar technology in use but it is faced with problems of material scarcity and toxicity. An alternative earth abundant and non-toxic materials consisting of Cu2ZnSnS4 (CZTS) have been investigated as a replacement for CIGS. In this work, CZTS thin films deposited by low cost co-electrodeposition, at a potential of ‑1.2V, coupled with chemical bath techniques at room temperature and then annealed under sulphur rich atmosphere were investigated. CZTS thin film quality determination was carried out using Raman spectroscopy which confirmed formation of quality CZTS film, main Raman peaks at 288cm‑1 and 338cm‑1 were observed. Electrical characterization was carried out using four-point probe instrument and the resistivity was in the order of ˜10‑4Ω-cm. The optical characterization was done using UV-VIS-NIR spectrophotometer. The bandgaps of the annealed CZTS film ranged from 1.45 to 1.94eV with absorption coefficient of order ˜104cm‑1 in the visible and near infrared range of the solar spectrum were observed.

  12. Effect of laser energy on the electrical transport properties of La{sub 0.67}Ca{sub 0.33}MnO{sub 3}:Ag{sub 0.2} films by pulsed laser deposition technique

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Yalin; Chen, Qingming; Jin, Fei; Chen, Xiaohui; Li, Zhiyu; Li, Di; Zhang, Hui [Kunming University of Science and Technology, Faculty of Materials Science and Engineering, Kunming (China)

    2017-09-15

    La{sub 0.67}Ca{sub 0.33}MnO{sub 3} (LCMO):Ag{sub 0.2} films were grown on LaAlO{sub 3} (LAO) substrates (100) by pulsed laser deposition (PLD) technique with various incident laser energies. The surface morphologies and the thicknesses of the films were studied by atomic force microscopy (AFM) and scanning electron microscopy (SEM), respectively. The crystal structures were analyzed by X-ray, diffraction (XRD), and the temperature dependence of the resistivity (ρ-T) of the films was studied by the standard four-probe method. It can be found that the crystal quality, surface morphology, metal-insulator transition temperature (T{sub p}), and temperature coefficient of resistance (TCR) of the LCMO:Ag{sub 0.2} films are changed with various laser energy. The highest T{sub p} 287 K is obtained with 300 mJ laser energy; meanwhile, the optimal TCR 13.5% K{sup -1} is achieved. The results suggest that the electrical transport properties of LCMO:Ag{sub 0.2} films are affected by the interface-induced compressive stress, the oxygen balance, and the double exchange between Mn{sup 3+}-O-Mn{sup 4+}. (orig.)

  13. Effect of a reducing agent for silver on the electrochemical activity of an Ag/Ba 0.5Sr 0.5Co 0.8Fe 0.2O 3- δ electrode prepared by electroless deposition technique

    Science.gov (United States)

    Zhou, Wei; Ran, Ran; Cai, Rui; Shao, Zongping; Jin, Wanqin; Xu, Nanping

    Silver-modified Ba 0.5Sr 0.5Co 0.8Fe 0.2O 3- δ (Ag/BSCF) electrodes were prepared using an electroless deposition technique. The morphology, microstructure and oxygen reduction reaction activity of the resulted Ag/BSCF electrodes were comparatively studied using Fourier transform infrared spectra, environmental scanning electron microscopy, temperature-programmed oxygen desorption, X-ray diffraction, and electrochemical impedance spectroscopy. An area-specific resistance as low as 0.038 Ω cm 2 was achieved for N 2H 4-reduced Ag/BSCF cathode at 600 °C. Carbonates were detected over the BSCF surface during the reduction of silver, which deteriorated both the charge-transfer process and diffusion process of HCHO-reduced Ag/BSCF cathode for the oxygen electrochemical reduction reaction. An anode-supported single cell with an N 2H 4-reduced Ag/BSCF cathode showed a peak power of 826 mW cm -2 at 600 °C. In comparison, only 672 mW cm -2 was observed with the HCHO-reduced Ag/BSCF cathode.

  14. Imposed layer by layer growth by pulsed laser interval deposition

    NARCIS (Netherlands)

    Koster, Gertjan; Rijnders, Augustinus J.H.M.; Blank, David H.A.; Rogalla, Horst

    1999-01-01

    Pulsed laser deposition has become an important technique to fabricate novel materials. Although there is the general impression that, due to the pulsed deposition, the growth mechanism differs partially from continuous physical and chemical deposition techniques, it has hardly been used. Here, we

  15. La{sub x}A{sub 1-x}MnO{sub 3} (A = Sr,Ca)/Y Ba{sub 2}Cu{sub 3}O{sub 7-{delta}} superlattices deposited by the 'eclipse' pulsed laser deposition technique

    Energy Technology Data Exchange (ETDEWEB)

    Pang, B S H; Tomov, R I; Blamire, M G [Device Materials Group, Department of Materials Science and Metallurgy, University of Cambridge, CB2 3QZ (United Kingdom)

    2004-04-01

    Multilayered structures of La{sub x}Sr{sub 1-x}MnO{sub 3} (LSMO), La{sub x}Ca{sub 1-x}MnO{sub 3} (LCMO) and Y Ba{sub 2}Cu{sub 3}O{sub 7-{delta}} (YBCO) were successfully grown by 'eclipse' pulsed laser ablation deposition (PLD) on (100) SrTiO{sub 3} and (100) NdGaO{sub 3} substrates. X-ray diffraction and scanning electron microscopy were used to investigate epitaxial growth, interface quality and structural disorder. The composition and the roughness of the films was characterized by energy dispersive x-rays (EDX) and atomic force microscopy (AFM) respectively. The results are discussed in terms of the optimization of PLD parameters and the establishment of its limits. Issues such as interdiffusion and particulate contamination reduction as well as utilizations of the 'eclipse' technique are addressed. The interaction between superconductivity and magnetism was investigated by varying the thicknesses of YBCO layers while the keeping the thicknesses of the ferromagnetic layers constant.

  16. Application of design of experiment on electrophoretic deposition of ...

    Indian Academy of Sciences (India)

    Unknown

    ceramic coating materials on metal substrate by electrophoretic deposition technique in an aqueous medium has been described. The effects of various process parameters, e.g. coating material concentration, time of deposition, applied current, pH ...

  17. Shedding of ash deposits

    DEFF Research Database (Denmark)

    Zbogar, Ana; Frandsen, Flemming; Jensen, Peter Arendt

    2009-01-01

    . Deposit shedding can be defined as the process of deposit removal from the heat transfer surfaces. Mechanical and thermal shock devices for deposit removal can be implemented within into the boiler, which can be then referred to as artificial shedding. Sootblowing is one such process, where a pressurized...... on the ash characteristics and the boiler operation. Different deposit characteristics will govern the ash deposit behaviour, and thus the mechanism of deposit shedding. The deposit strength will influence the erosion and gravity shedding mechanisms. The ash viscosity and the melting behaviour will govern...

  18. Depositing Materials on the Micro- and Nanoscale

    DEFF Research Database (Denmark)

    Mar, Mikkel Dysseholm; Herstrøm, Berit; Shkondin, Evgeniy

    2014-01-01

    , layers with specific optical properties in optical sensors, piezoelectric thin films or insulating layers in many other applications. These different materials and properties impose a demand for different kind of deposition techniques. At DTU Danchip we have a large variety of these deposition techniques......Micro- and nanotechnology systems are important in many sustainable products like solar cells and chemical, mechanical and optical sensors. Keeping the systems small will make a smaller demand for material and energy during production and also a smaller demand for energy during use......) is good for fabricating dielectric layers for opticalcomponents and insulation layers. The layers are deposited at relative low temperature (300C). Sputter deposition deposits almost any material (metals and dielectrics including alloys) at low temperaturewith good step coverage. E-beam evaporation...

  19. Crystalline thin films: The electrochemical atomic layer deposition (ECALD) view

    CSIR Research Space (South Africa)

    Modibedi, M

    2011-09-01

    Full Text Available Electrochemical atomic layer deposition technique is selected as one of the methods to prepare thin films for various applications, including electrocatalytic materials and compound....

  20. Experimental measurements of the thermal conductivity of ash deposits: Part 2. Effects of sintering and deposit microstructure

    Energy Technology Data Exchange (ETDEWEB)

    A. L. Robinson; S. G. Buckley; N. Yang; L. L. Baxter

    2000-04-01

    The authors report results from an experimental study that examines the influence of sintering and microstructure on ash deposit thermal conductivity. The measurements are made using a technique developed to make in situ, time-resolved measurements of the effective thermal conductivity of ash deposits formed under conditions that closely replicate those found in the convective pass of a commercial boiler. The technique is designed to minimize the disturbance of the natural deposit microstructure. The initial stages of sintering and densification are accompanied by an increase in deposit thermal conductivity. Subsequent sintering continues to densify the deposit, but has little effect on deposit thermal conductivity. SEM analyses indicates that sintering creates a layered deposit structure with a relatively unsintered innermost layer. They hypothesize that this unsintered layer largely determines the overall deposit thermal conductivity. A theoretical model that treats a deposit as a two-layered material predicts the observed trends in thermal conductivity.

  1. The business of fast ALD equipment for depositing alumina passivation layers on crystalline silicon solar cells

    NARCIS (Netherlands)

    Vermeer, A.J.P.M.; Gortzen, R.M.W.; Poodt, P.W.G.; Roozeboom, F.

    2011-01-01

    Atomic Layer Deposition (ALD) is a gas phase deposition technique for depositing very high quality thin films with an unsurpassed conformality. The main drawback of ALD however is the very low deposition rate (∼ 1 nm/min). Recently, record deposition rates for alumina of up to 1 nm/s were reached

  2. TPR system: a powerful technique to monitor carbon nanotube formation during chemical vapour deposition; Sistema RTP: uma tecnica poderosa para o monitoramento da formacao de nanotubos de carbono durante o processo por deposicao de vapor quimico

    Energy Technology Data Exchange (ETDEWEB)

    Tristao, Juliana Cristina; Moura, Flavia Cristina Camilo; Lago, Rochel Montero, E-mail: rochel@ufmg.b [Universidade Federal de Minas Gerais (DQ/UFMG), Belo Horizonte, MG (Brazil). Dept. de Quimica; Sapag, Karim [Universidade Nacional de San Luis (Argentina). Lab. de Ciencias de Superficies y Medios Porosos

    2010-07-01

    In this work, a TPR (Temperature Programmed Reduction) system is used as a powerful tool to monitor carbon nanotubes production during CVD (Chemical Vapour Deposition), The experiments were carried out using catalyst precursors based on Fe-Mo supported on Al{sub 2}O{sub 3} and methane as carbon source. As methane reacts on the Fe metal surface, carbon is deposited and H2 is produced. TPR is very sensitive to the presence of H2 and affords information on the temperature where catalyst is active to form different forms of carbon, the reaction kinetics, the catalyst deactivation and carbon yields. (author)

  3. Chemical solution deposition of functional oxide thin films

    CERN Document Server

    Schneller, Theodor; Kosec, Marija

    2014-01-01

    Chemical Solution Deposition (CSD) is a highly-flexible and inexpensive technique for the fabrication of functional oxide thin films. Featuring nearly 400 illustrations, this text covers all aspects of the technique.

  4. Atmospheric Deposition Modeling Results

    Data.gov (United States)

    U.S. Environmental Protection Agency — This asset provides data on model results for dry and total deposition of sulfur, nitrogen and base cation species. Components include deposition velocities, dry...

  5. Electro-Deposition Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — The electro-deposition laboratory can electro-deposit various coatings onto small test samples and bench level prototypes. This facility provides the foundation for...

  6. Effects of deposition time in chemically deposited ZnS films in acidic solution

    Energy Technology Data Exchange (ETDEWEB)

    Haddad, H.; Chelouche, A., E-mail: azeddinechelouche@gmail.com; Talantikite, D.; Merzouk, H.; Boudjouan, F.; Djouadi, D.

    2015-08-31

    We report an experimental study on the synthesis and characterization of zinc sulfide (ZnS) single layer thin films deposited on glass substrates by chemical bath deposition technique in acidic solution. The effect of deposition time on the microstructure, surface morphology, optical absorption, transmittance, and photoluminescence (PL) was investigated by X-ray diffraction (XRD), scanning electronic microscopy (SEM), UV-Vis–NIR spectrophotometry and photoluminescence (PL) spectroscopy. The results showed that the samples exhibit wurtzite structure and their crystal quality is improved by increasing deposition time. The latter, was found to affect the morphology of the thin films as showed by SEM micrographs. The optical measurements revealed a high transparency in the visible range and a dependence of absorption edge and band gap on deposition time. The room temperature PL spectra indicated that all ZnS grown thin films emit a UV and blue light, while the band intensities are found to be dependent on deposition times. - Highlights: • Single layer ZnS thin films were deposited by CBD in acidic solution at 95 °C. • The effect of deposition time was investigated. • Coexistence of ZnS and ZnO hexagonal structures for time deposition below 2 h • Thicker ZnS films were achieved after monolayer deposition for 5 h. • The highest UV-blue emission observed in thin film deposited at 5 h.

  7. Structural characterization of MAPLE deposited lipase biofilm

    Energy Technology Data Exchange (ETDEWEB)

    Aronne, Antonio [Department of Chemical Engineering, Materials and Industrial Production, Università degli Studi di Napoli Federico II, Piazzale V. Tecchio 80, 80125 Napoli (Italy); Ausanio, Giovanni; Bloisi, Francesco [CNR-SPIN and Department of Physics, Università degli Studi di Napoli Federico II, Piazzale V. Tecchio 80, 80125 Napoli (Italy); Calabria, Raffaela [Istituto Motori-CNR, via G. Marconi 8, 80125 Napoli (Italy); Califano, Valeria, E-mail: v.califano@im.cnr.it [Istituto Motori-CNR, via G. Marconi 8, 80125 Napoli (Italy); Fanelli, Esther [Department of Chemical Engineering, Materials and Industrial Production, Università degli Studi di Napoli Federico II, Piazzale V. Tecchio 80, 80125 Napoli (Italy); Massoli, Patrizio [Istituto Motori-CNR, via G. Marconi 8, 80125 Napoli (Italy); Vicari, Luciano R.M. [CNR-SPIN and Department of Physics, Università degli Studi di Napoli Federico II, Piazzale V. Tecchio 80, 80125 Napoli (Italy)

    2014-11-30

    Highlights: • Lipase from Candida Rugosa was deposited by Matrix Assisted Pulsed Laser Evaporation (MAPLE) on KBr pellets, mica and glass substrate. • The deposited film was characterized morphologically and structurally by optical microscopy, SEM and FTIR analysis. • Results of characterization underlined a phenomenon of aggregation taking place. • The aggregation phenomenon was reversible since lipase showed activity in the transesterification reaction between soybean oil and isopropyl alcohol once detached from the substrate. - Abstract: Lipases (triacylglycerol ester hydrolases) are enzymes used in several industrial applications. Enzymes immobilization can be used to address key issues limiting widespread application at industrial level. Immobilization efficiency is related to the ability to preserve the native conformation of the enzyme. MAPLE (Matrix Assisted Pulsed Laser Evaporation) technique, a laser deposition procedure for treating organic/polymeric/biomaterials, was applied for the deposition of lipase enzyme in an ice matrix, using near infrared laser radiation. Microscopy analysis showed that the deposition occurred in micrometric and submicrometric clusters with a wide size distribution. AFM imaging showed that inter-cluster regions are uniformly covered with smaller aggregates of nanometric size. Fourier transform infrared spectroscopy was used for both recognizing the deposited material and analyzing its secondary structure. Results showed that the protein underwent reversible self-association during the deposition process. Actually, preliminary tests of MAPLE deposited lipase used for soybean oil transesterification with isopropyl alcohol followed by gas chromatography–mass spectrometry gave results consistent with undamaged deposition of lipase.

  8. Advanced deposition model for thermal activated chemical vapor deposition

    Science.gov (United States)

    Cai, Dang

    Thermal Activated Chemical Vapor Deposition (TACVD) is defined as the formation of a stable solid product on a heated substrate surface from chemical reactions and/or dissociation of gaseous reactants in an activated environment. It has become an essential process for producing solid film, bulk material, coating, fibers, powders and monolithic components. Global market of CVD products has reached multi billions dollars for each year. In the recent years CVD process has been extensively used to manufacture semiconductors and other electronic components such as polysilicon, AlN and GaN. Extensive research effort has been directed to improve deposition quality and throughput. To obtain fast and high quality deposition, operational conditions such as temperature, pressure, fluid velocity and species concentration and geometry conditions such as source-substrate distance need to be well controlled in a CVD system. This thesis will focus on design of CVD processes through understanding the transport and reaction phenomena in the growth reactor. Since the in situ monitor is almost impossible for CVD reactor, many industrial resources have been expended to determine the optimum design by semi-empirical methods and trial-and-error procedures. This approach has allowed the achievement of improvements in the deposition sequence, but begins to show its limitations, as this method cannot always fulfill the more and more stringent specifications of the industry. To resolve this problem, numerical simulation is widely used in studying the growth techniques. The difficulty of numerical simulation of TACVD crystal growth process lies in the simulation of gas phase and surface reactions, especially the latter one, due to the fact that very limited kinetic information is available in the open literature. In this thesis, an advanced deposition model was developed to study the multi-component fluid flow, homogeneous gas phase reactions inside the reactor chamber, heterogeneous surface

  9. The study and the realization of radiation detectors made from polycrystalline diamond films grown by microwave plasma enhanced chemical vapour deposition technique; Etude et realisation de detecteurs de rayonnements a base de films de diamant polycristallin elabores par depot chimique en phase vapeur assiste par plasma micro-onde

    Energy Technology Data Exchange (ETDEWEB)

    Jany, Ch

    1998-10-29

    The aim of this work was to develop radiation detectors made from polycrystalline diamond films grown by microwave plasma enhanced chemical vapour deposition technique. The influence of surface treatments, contact technology and diamond growth parameters on the diamond detectors characteristics was investigated in order to optimise the detector response to alpha particles. The first part of the study focused on the electrical behaviour of as-deposited diamond surface, showing a p type conduction and its influence on the leakage current of the device. A surface preparation process was established in order to reduce the leakage current of the device by surface dehydrogenation using an oxidising step. Several methods to form and treat electrical contacts were also investigated showing that the collection efficiency of the device decreases after contact annealing. In the second part, we reported the influence of the diamond deposition parameters on the characteristics of the detectors. The increase of the deposition temperature and/or methane concentration was shown to lead {eta} to decrease. In contrast, {eta} was found to increase with the micro-wave power. The evolution of the diamond detector characteristics results from the variation in sp{sup 2} phases incorporation and in the crystallography quality of the films. These defects increase the leakage current and reduce the carrier mobility and lifetime. Measurements carried out on detectors with different thicknesses showed that the physical properties varies along the growth direction, improving with the film thickness. Finally, the addition of nitrogen (> 10 ppm) in the gas mixture during diamond deposition was found to strongly reduce the collection efficiency of the detectors. To conclude the study, we fabricated and characterised diamond devices which were used for thermal neutron detection and for the intensity and shape measurement of VUV and soft X-ray pulses. (author)

  10. Structural and Optical Properties of Chemical Bath Deposited Silver Oxide Thin Films: Role of Deposition Time

    Directory of Open Access Journals (Sweden)

    A. C. Nwanya

    2013-01-01

    Full Text Available Silver oxide thin films were deposited on glass substrates at a temperature of 50°C by chemical bath deposition technique under different deposition times using pure AgNO3 precursor and triethanolamine as the complexing agent. The chemical analysis based on EDX technique shows the presence of Ag and O at the appropriate energy levels. The morphological features obtained from SEM showed that the AgxO structures varied as the deposition time changes. The X-ray diffraction showed the peaks of Ag2O and AgO in the structure. The direct band gap and the refractive index increased as the deposition time increased and was in the range of 1.64–1.95 eV and 1.02–2.07, respectively. The values of the band gap and refractive index obtained indicate possible applications in photovoltaic and photothermal systems.

  11. Luminescence dating of glaciofluvial deposits: A review

    Science.gov (United States)

    Thrasher, I. M.; Mauz, B.; Chiverrell, R. C.; Lang, A.

    2009-12-01

    For glacigenic sediments, Optically Stimulated Luminescence (OSL) dating offers an opportunity to date the time of deposition of quartz and feldspar minerals that are ubiquitous within the sediment matrix, rather than relying upon the chance occurrence of organic material for radiocarbon dating. The OSL dating signal or charge accumulates in crystal defects of individual quartz and feldspar minerals through exposure to environmental radiation within their depositional setting. The OSL signal within individual grains can be reset or bleached through exposure to daylight during transportation processes. Thus OSL dating of sediments attempts to determine the time elapsed since burial. Glacigenic sediments present considerable challenges for OSL dating not only in terms of poor bleaching of the OSL signal during the transport and deposition cycle, but also poor quartz luminescence characteristics which are often related to sediment provenance, the nature of the bedrock or source material, and the freshly eroded nature of many such deposits. This paper reviews luminescence dating techniques as applied to glaciofluvial sediments and explores the challenges that such deposits present to the technique. Successful application of OSL techniques can be judged in a number of ways: comparison with the 'independent' chronologies is prevalent in the literature, but recently the movement towards measurement of large numbers of small aliquots and single grains allows a more robust assessment of luminescence properties and behaviour for individual samples and ultimately more precise luminescence ages to be determined. For glaciofluvial sediments in particular, it is important to investigate the depositional sub-environment of each sample in relation to the chance of sufficient bleaching during transport and deposition. A lithofacies-based approach to sampling for optically stimulated luminescence dating of these sediments is suggested whereby hypothetically well-bleached deposits

  12. Acid Deposition Phenomena

    International Nuclear Information System (INIS)

    Ramadan, A.E.K.

    2004-01-01

    Acid deposition, commonly known as acid rain, occurs when emissions from the combustion of fossil fuels and other industrial processes undergo complex chemical reactions in the atmosphere and fall to the earth as wet deposition (rain, snow, cloud, fog) or dry deposition (dry particles, gas). Rain and snow are already naturally acidic, but are only considered problematic when less than a ph of 5.0 The main chemical precursors leading to acidic conditions are atmospheric concentrations of sulfur dioxide (SO 2 ) and nitrogen oxides (NO x ). When these two compounds react with water, oxygen, and sunlight in the atmosphere, the result is sulfuric (H 2 SO 4 ) and nitric acids (HNO 3 ), the primary agents of acid deposition which mainly produced from the combustion of fossil fuel and from petroleum refinery. Airborne chemicals can travel long distances from their sources and can therefore affect ecosystems over broad regional scales and in locations far from the sources of emissions. According to the concern of petroleum ministry with the environment and occupational health, in this paper we will discussed the acid deposition phenomena through the following: Types of acidic deposition and its components in the atmosphere Natural and man-made sources of compounds causing the acidic deposition. Chemical reactions causing the acidic deposition phenomenon in the atmosphere. Factors affecting level of acidic deposition in the atmosphere. Impact of acid deposition. Procedures for acidic deposition control in petroleum industry

  13. A novel passivation process of silicon nanowires by a low-cost PECVD technique for deposition of hydrogenated silicon nitride using SiH4 and N2 as precursor gases

    Science.gov (United States)

    Bouaziz, Lamia; Dridi, Donia; Karyaoui, Mokhtar; Angelova, Todora; Sanchez Plaza, Guillermo; Chtourou, Radhouane

    2017-03-01

    In this work, a different SiNx passivation process of silicon nanowires has been opted for the deposition of a hydrogenated silicon nitride (SiNx:H) by a low-cost plasma enhanced chemical vapor deposition (PECVD) using silane ( SiH4 and nitrogen ( N2 as reactive gases. This study is focused on the effect of the gas flow ratio on chemical composition, morphological, optical and optoelectronic properties of silicon nanowires. The existence of Si-N and Si-H bonds was proven by the Fourier transmission infrared (FTIR) spectrum. Morphological structures were shown by scanning electron microscopy (SEM), and the roughness was investigated by atomic force microscopy (AFM). A low reflectivity less than 6% in the wavelength range 250-1200nm has been shown by UV-visible spectroscopy. Furthermore, the thickness and the refractive index of the passivation layer is determined by ellipsometry measurements. As a result, an improvement in minority carrier lifetime has been obtained by reducing surface recombination of silicon nanowires.

  14. Atomic Layer Deposition of zinc oxide for solar cell applications

    Science.gov (United States)

    Moret, M.; Abou Chaaya, A.; Bechelany, M.; Miele, P.; Robin, Y.; Briot, O.

    2014-11-01

    Atomic Layer Deposition (ALD) is a vapor phase thin film deposition technique, performed at low substrate temperatures, which enables the deposition of extremely uniform thin films. This technique is scalable up to very large substrates, making it very interesting for industrial applications. On the other hand, ZnO, both undoped and aluminum doped is commonly used as a transparent electrode in solar cells based on Cu(In,Ga)Se2 (CIGS), and is usually deposited by Physical Vapor Deposition techniques. In this paper, we investigate the potential of ALD for the deposition of ZnO windows for solar cell applications. Thin films of a few hundreds of nanometers were grown by ALD, both undoped and doped with aluminum. They were studied by X-ray diffraction, electrical transport measurements, Atomic Force Microscopy and transmittance experiments.

  15. Deposition Measurements in NSTX

    Science.gov (United States)

    Skinner, C. H.; Kugel, H. W.; Hogan, J. T.; Wampler, W. R.

    2004-11-01

    Two quartz microbalances have been used to record deposition on the National Spherical Torus Experiment. The experimental configuration mimics a typical diagnostic window or mirror. An RS232 link was used to acquire the quartz crystal frequency and the deposited thickness was recorded continuously with 0.01 nm resolution. Nuclear Reaction Analysis of the deposit was consistent with the measurement of the total deposited mass from the change in crystal frequency. We will present measurements of the variation of deposition with plasma conditions. The transport of carbon impurities in NSTX has been modelled with the BBQ code. Preliminary calculations indicated a negligible fraction of carbon generated at the divertor plates in quiescent discharges directly reaches the outer wall, and that transient events are responsible for the deposition.

  16. Monte Carlo alpha deposition

    International Nuclear Information System (INIS)

    Talley, T.L.; Evans, F.

    1988-01-01

    Prior work demonstrated the importance of nuclear scattering to fusion product energy deposition in hot plasmas. This suggests careful examination of nuclear physics details in burning plasma simulations. An existing Monte Carlo fast ion transport code is being expanded to be a test bed for this examination. An initial extension, the energy deposition of fast alpha particles in a hot deuterium plasma, is reported. The deposition times and deposition ranges are modified by allowing nuclear scattering. Up to 10% of the initial alpha particle energy is carried to greater ranges and times by the more mobile recoil deuterons. 4 refs., 5 figs., 2 tabs

  17. Uraniferous surficial deposits

    International Nuclear Information System (INIS)

    Toens, P.D.; Hambleton-Jones, B.B.

    1980-10-01

    As a result of the discovery of uranium in surficial deposits of Tertiary to Recent age, in Australia and Southern Africa, increasing attention is being paid to the location and understanding of the genesis of these deposits. The paper discusses the definitions and terminology currently in use and a classification of these deposits is presented. It is concluded that in order to obtain a measure of clarity, the terms calcrete, gypcrete and dolocrete should not be used to describe the uraniferous valley-fill deposits of Southern Africa and Australia [af

  18. Ultrafast atomic layer deposition of alumina layers for solar cell passivation

    NARCIS (Netherlands)

    Poodt, P.W.G.; Lankhorst, A.M.; Roozeboom, F.; Tiba, V.; Spee, K.; Maas, D.; Vermeer, A.

    2010-01-01

    An ultrafast atomic layer deposition technique is presented, based on the spatial separation of the half-reactions, with which alumina layers can be deposited with deposition rates of more than 1 nm/s. The deposition rate is limited by the water half-reaction, for which a kinetic model has been

  19. Panel 1 - comparative evaluation of deposition technologies

    Energy Technology Data Exchange (ETDEWEB)

    Fenske, G.R.; Stodolsky, F. [Argonne National Lab., IL (United States); Benson, D.K.; Pitts, R.J. [National Renewable Energy Lab., Golden, CO (United States); Bhat, D.G. [GTE Valenite Corp., Troy, MI (United States); Yulin Chen [Allison Gas Turbine Division, GM, Indianapolis, IN (United States); Gat, R.; Sunkara, M.K. [Case Western Reserve Univ., Cleveland, OH (United States); Kelly, M. [Stanford Univ., CA (United States); Lawler, J.E. [Univ. of Wisconsin, Madison (United States); Nagle, D.C. [Martin Marietta Labs., Baltimore, MD (United States); Outka, D. [Sandia National Laboratories, Livermore, CA (United States); Revankar, G.S. [Deere & Co., Moline, IL (United States); Subramaniam, V.V. [Ohio State Univ., Columbus (United States); Wilbur, P.J. [Colorado State Univ., Fort Collins (United States); Mingshow Wong [Northwestern Univ., Evanston, IL (United States); Woolam, W.E. [Southwest Research Inst., Arlington, VA (United States)

    1993-01-01

    This working group attempted to evaluate/compare the different types of deposition techniques currently under investigation for depositing diamond and diamond-like carbon films. A table lists the broad types of techniques that were considered for depositing diamond and diamond-like carbon films. After some discussion, it was agreed that any evaluation of the various techniques would be dependent on the end application. Thus the next action was to list the different areas where diamond and DLC films could find applications in transportation. These application areas are listed in a table. The table intentionally does not go into great detail on applications because that subject is dealt with specifically by Panel No. 4 - Applications To Transportation. The next action concentrated on identifying critical issues or limitations that need to be considered in evaluating the different processes. An attempt was then made to rank different broad categories of deposition techniques currently available or under development based on the four application areas and the limitations. These rankings/evaluations are given for diamond and DLC techniques. Finally, the working group tried to identify critical development and research issues that need to be incorporated into developing a long-term program that focuses on diamond/DLC coatings for transportation needs. 5 tabs.

  20. Adhesion of laser deposited films

    International Nuclear Information System (INIS)

    Zhovannik, E.V.; Nikolaev, I.N.; Utochkin, Yu.A.; Stavkin, D.G.

    1996-01-01

    The method of thin solid films (Ni, Cu, Al, Pd, Si, InSb, Ta 2 O 5 ) formation on different substrates (Cu, Fe, Si, SiO 2 , Ta 2 O 5 , carbon, glass, mica, teflon) with higher adhesion strength (∼ 10 7 Pa) without preliminary treatment of substrate surface was discribed. The method is based on laser evaporation of solid in vacuum. Adhesion was measured by means of a direct pull technique using a pin soldered to buffer film evaporated by laser on the investigated film. Possible reasons for higher adhesion of films fabricated by laser deposition were discussed. 10 refs.; 3 figs

  1. Minerals deposited as thin films

    International Nuclear Information System (INIS)

    Vazquez, Cristina; Leyt, D.V. de; Custo, Graciela

    1987-01-01

    Free matrix effects are due to thin film deposits. Thus, it was decided to investigate this technique as a possibility to use pure oxide of the desired element, extrapolating its concentration from analytical curves made with avoiding, at the same time, mathematical corrections. The proposed method was employed to determine iron and titanium concentrations in geological samples. The range studied was 0.1-5%m/m for titanium and 5-20%m/m for iron. For both elements the reproducibility was about 7% and differences between this method and other chemical determinations were 15% for titanium and 7% for iron. (Author) [es

  2. Stratiform chromite deposit model

    Science.gov (United States)

    Schulte, Ruth F.; Taylor, Ryan D.; Piatak, Nadine M.; Seal, Robert R.

    2010-01-01

    Stratiform chromite deposits are of great economic importance, yet their origin and evolution remain highly debated. Layered igneous intrusions such as the Bushveld, Great Dyke, Kemi, and Stillwater Complexes, provide opportunities for studying magmatic differentiation processes and assimilation within the crust, as well as related ore-deposit formation. Chromite-rich seams within layered intrusions host the majority of the world's chromium reserves and may contain significant platinum-group-element (PGE) mineralization. This model of stratiform chromite deposits is part of an effort by the U.S. Geological Survey's Mineral Resources Program to update existing models and develop new descriptive mineral deposit models to supplement previously published models for use in mineral-resource and mineral-environmental assessments. The model focuses on features that may be common to all stratiform chromite deposits as a way to gain insight into the processes that gave rise to their emplacement and to the significant economic resources contained in them.

  3. Solution deposition assembly

    Science.gov (United States)

    Roussillon, Yann; Scholz, Jeremy H; Shelton, Addison; Green, Geoff T; Utthachoo, Piyaphant

    2014-01-21

    Methods and devices are provided for improved deposition systems. In one embodiment of the present invention, a deposition system is provided for use with a solution and a substrate. The system comprises of a solution deposition apparatus; at least one heating chamber, at least one assembly for holding a solution over the substrate; and a substrate curling apparatus for curling at least one edge of the substrate to define a zone capable of containing a volume of the solution over the substrate. In another embodiment of the present invention, a deposition system for use with a substrate, the system comprising a solution deposition apparatus; at heating chamber; and at least assembly for holding solution over the substrate to allow for a depth of at least about 0.5 microns to 10 mm.

  4. Structural characterization of MAPLE deposited lipase biofilm

    Science.gov (United States)

    Aronne, Antonio; Ausanio, Giovanni; Bloisi, Francesco; Calabria, Raffaela; Califano, Valeria; Fanelli, Esther; Massoli, Patrizio; Vicari, Luciano R. M.

    2014-11-01

    Lipases (triacylglycerol ester hydrolases) are enzymes used in several industrial applications. Enzymes immobilization can be used to address key issues limiting widespread application at industrial level. Immobilization efficiency is related to the ability to preserve the native conformation of the enzyme. MAPLE (Matrix Assisted Pulsed Laser Evaporation) technique, a laser deposition procedure for treating organic/polymeric/biomaterials, was applied for the deposition of lipase enzyme in an ice matrix, using near infrared laser radiation. Microscopy analysis showed that the deposition occurred in micrometric and submicrometric clusters with a wide size distribution. AFM imaging showed that inter-cluster regions are uniformly covered with smaller aggregates of nanometric size. Fourier transform infrared spectroscopy was used for both recognizing the deposited material and analyzing its secondary structure. Results showed that the protein underwent reversible self-association during the deposition process. Actually, preliminary tests of MAPLE deposited lipase used for soybean oil transesterification with isopropyl alcohol followed by gas chromatography-mass spectrometry gave results consistent with undamaged deposition of lipase.

  5. Electroless atomic layer deposition

    Science.gov (United States)

    Robinson, David Bruce; Cappillino, Patrick J.; Sheridan, Leah B.; Stickney, John L.; Benson, David M.

    2017-10-31

    A method of electroless atomic layer deposition is described. The method electrolessly generates a layer of sacrificial material on a surface of a first material. The method adds doses of a solution of a second material to the substrate. The method performs a galvanic exchange reaction to oxidize away the layer of the sacrificial material and deposit a layer of the second material on the surface of the first material. The method can be repeated for a plurality of iterations in order to deposit a desired thickness of the second material on the surface of the first material.

  6. Deposition of tantalum carbide coatings on graphite by laser interactions

    Science.gov (United States)

    Veligdan, James; Branch, D.; Vanier, P. E.; Barietta, R. E.

    1994-01-01

    Graphite surfaces can be hardened and protected from erosion by hydrogen at high temperatures by refractory metal carbide coatings, which are usually prepared by chemical vapor deposition (CVD) or chemical vapor reaction (CVR) methods. These techniques rely on heating the substrate to a temperature where a volatile metal halide decomposes and reacts with either a hydrocarbon gas or with carbon from the substrate. For CVR techniques, deposition temperatures must be in excess of 2000 C in order to achieve favorable deposition kinetics. In an effort to lower the bulk substrate deposition temperature, the use of laser interactions with both the substrate and the metal halide deposition gas has been employed. Initial testing involved the use of a CO2 laser to heat the surface of a graphite substrate and a KrF excimer laser to accomplish a photodecomposition of TaCl5 gas near the substrate. The results of preliminary experiments using these techniques are described.

  7. Modification of thin film properties by ion bombardment during deposition

    International Nuclear Information System (INIS)

    Harper, J.M.E.; Cuomo, J.J.; Gambino, R.J.; Kaufman, H.R.

    1984-01-01

    Deposition methods involving ion bombardment are described, and the basic processes with which film properties are modified by ion bombardment are summarized. Examples of thin film property modification by ion bombardment during deposition, including effects which are primarily compositional as well as those which are primarily structural are presented. The examples demonstrate the usefulness of ion beam techniques in identifying and controlling the fundamental deposition parameters. 68 refs.; 15 figs.; 1 table

  8. Application of Neural Networks Technique in depositional environment interpretation for the Niger Delta a Novel computer-Based methodology for 3-D reservoir geological modelling and exploration studies. (The pilot application in X-Field, Niger Delta)

    International Nuclear Information System (INIS)

    Iloghalu, E.M.

    2002-01-01

    Artificial neural network is a virtual intelligence tool, which mimics the human brain to do analysis and come out with results. Its application in petroleum engineering is very recent and is gradually evolving and is set to dominate or take over other analytical tools used in the Exploration and Production industry.There are two types of neural network namely, unsupervised and supervised neural networks. A proper combination of these two types of neural networks produces high-resolution results.In this work, interpreted core data was depth matched to well logs and 5 genetic units were calibrated to define the combined log responses for each genetic unit. These combined log responses were then used to train the supervised neural networks to recognise and interpret these units elsewhere in the field. Thereafter, the unsupervised neural network was run to generate classes within the cored interval. The results were then compared with the supervised network output and were then extrapolated vertically and laterally to other parts of the field.This technique having been used successfully to perform automatic interpretation of genetic units and lithofacies associations in reservoir scale is also very useful and applicable in exploration. Specific reservoirs or stratigraphic units can be automatically interpreted across a wide area using well data controlled by one or a combination of lithostratigraphy, allostratigraphy, sequence stratigraphy and biostratigraphy.Using this technique, well data cost and time are saved tremendously. It is the key to achieving computerised Basin-Scale Reservoir characterisation for the Niger Delta

  9. A method of quantitative prediction for sandstone type uranium deposit in Russia and its application

    International Nuclear Information System (INIS)

    Chang Shushuai; Jiang Minzhong; Li Xiaolu

    2008-01-01

    The paper presents the foundational principle of quantitative predication for sandstone type uranium deposits in Russia. Some key methods such as physical-mathematical model construction and deposits prediction are described. The method has been applied to deposits prediction in Dahongshan region of Chaoshui basin. It is concluded that the technique can fortify the method of quantitative predication for sandstone type uranium deposits, and it could be used as a new technique in China. (authors)

  10. Experimental techniques; Techniques experimentales

    Energy Technology Data Exchange (ETDEWEB)

    Roussel-Chomaz, P. [GANIL CNRS/IN2P3, CEA/DSM, 14 - Caen (France)

    2007-07-01

    This lecture presents the experimental techniques, developed in the last 10 or 15 years, in order to perform a new class of experiments with exotic nuclei, where the reactions induced by these nuclei allow to get information on their structure. A brief review of the secondary beams production methods will be given, with some examples of facilities in operation or under project. The important developments performed recently on cryogenic targets will be presented. The different detection systems will be reviewed, both the beam detectors before the targets, and the many kind of detectors necessary to detect all outgoing particles after the reaction: magnetic spectrometer for the heavy fragment, detection systems for the target recoil nucleus, {gamma} detectors. Finally, several typical examples of experiments will be detailed, in order to illustrate the use of each detector either alone, or in coincidence with others. (author)

  11. Mineral composition of deposits

    International Nuclear Information System (INIS)

    Khasanov, A.Kh.

    1988-01-01

    Studying of mineral and chemical composition of ores have immediate practical sense. It is a basic at solving problems of origin of deposit, choosing of most profitable method of their exploitation and problems of complex ores using

  12. Modeled Wet Nitrate Deposition

    Data.gov (United States)

    U.S. Environmental Protection Agency — Modeled data on nitrate wet deposition was obtained from Dr. Jeff Grimm at Penn State Univ. Nitrate wet depostion causes acidification and eutrophication of surface...

  13. Speleothem (Cave Deposit) Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Records of past temperature, precipitation, and other aspects of climate derived from mineral deposits found in caves. Parameter keywords describe what was measured...

  14. Uranium deposit research, 1983

    International Nuclear Information System (INIS)

    Ruzicka, V.; LeCheminant, G.M.

    1984-01-01

    Research on uranium deposits in Canada, conducted as a prerequisite for assessment of the Estimated Additional Resources of uranium, revealed that (a) the uranium-gold association in rudites of the Huronian Supergroup preferably occurs in the carbon layers; (b) chloritized ore at the Panel mine, Elliot Lake, Ontario, occurs locally in tectonically disturbed areas in the vicinity of diabase dykes; (c) mineralization in the Black Sturgeon Lake area, Ontario, formed from solutions in structural and lithological traps; (d) the Cigar Lake deposit, Saskatchewan, has two phases of mineralization: monomineralic and polymetallic; (e) mineralization of the JEB (Canoxy Ltd.) deposit is similar to that at McClean Lake; (f) the uranium-carbon assemblage was identified in the Claude deposit, Carswell Structure; and (g) the Otish Mountains area, Quebec, should be considered as a significant uranium-polymetallic metallogenic province

  15. Alluvial Deposits in Iowa

    Data.gov (United States)

    Iowa State University GIS Support and Research Facility — This coverage maps alluvial deposits throughout Iowa. This generally would include areas of alluvial soils associated with modern streams that are identified on...

  16. Radioactive raw material deposits

    International Nuclear Information System (INIS)

    Danchev, V.I.; Lapinskaya, T.A.

    1980-01-01

    Presented are the data on radioactive elements of the Earth, migration conditions and concentrations of uranium, radium and thorium. Briefly considered are the problems of radiogenic heat of the Earth, as well as the main methods of determining the absolute age of minerals and rocks. The main minerals of uranium and thorium are characterized, classification of their deposits is given. Primary attention is paid to the description of uranium deposits as the main sources of raw material for nuclear industry and nuclear power engineering. Among them in detail characterized are the exogenic deposits, confined mainly to sedimentary and sedimentary - metamorphized rocks as well as endogenic deposits, mainly hydrothermal ones, giving an essential part of commercial uranium. Special sections of the book deal with the problems of uranium bonds with coaly and bitumen materials, as well as the processes of ore-forming processes with the stages of ore-bearing rock formation

  17. Residual deposits (residual soil)

    International Nuclear Information System (INIS)

    Khasanov, A.Kh.

    1988-01-01

    Residual soil deposits is accumulation of new formate ore minerals on the earth surface, arise as a result of chemical decomposition of rocks. As is well known, at the hyper genes zone under the influence of different factors (water, carbonic acid, organic acids, oxygen, microorganism activity) passes chemical weathering of rocks. Residual soil deposits forming depends from complex of geologic and climatic factors and also from composition and physical and chemical properties of initial rocks

  18. Resedimented salt deposits

    Energy Technology Data Exchange (ETDEWEB)

    Slaczka, A.; Kolasa, K. (Jagiellonian Univ., Krakow (Poland))

    1988-08-01

    Carparthian foredeep's Wieliczka salt mine, unique gravity deposits were lately distinguished. They are mainly built of salt particles and blocks with a small admixture of fragments of Miocene marls and Carpathian rocks, deposited on precipitated salt. The pattern of sediment distribution is similar to a submarine fan. Gravels are dominant in the upper part and sands in lower levels, creating a series of lobes. Coarse-grained deposits are represented by disorganized, self-supported conglomerates passing into matrix-supported ones, locally with gradation, and pebbly sandstones consisting of salt grains and scattered boulder-size clasts. The latter may show in the upper part of a single bed as indistinct cross-bedding and parallel lamination. These sediments are interpreted as debris-flow and high-density turbidity current deposits. Salt sandstones (saltstones) which build a lower part of the fan often show Bouma sequences and are interpreted as turbidity-current deposits. The fan deposits are covered by a thick series of debrites (olistostromes) which consist of clay matrix with salt grains and boulders. The latter as represented by huge (up to 100,000 m{sup 3}) salt blocks, fragments of Miocene marls and Carpathian rocks. These salt debrites represent slumps and debris-flow deposits. The material for resedimented deposits was derived from the southern part of the salt basin and from the adjacent, advancing Carpathian orogen. The authors believe the distinct coarsening-upward sequence of the series is the result of progressive intensification of tectonic movements with paroxysm during the sedimentation of salt debrites (about 15 Ma).

  19. Optical Properties of Chemical Bath Deposited Bismuth Fluoride (Bif ...

    African Journals Online (AJOL)

    Thin films of bismuth fluoride (Bif3) were deposited using chemical bath deposition technique from chemical baths containing solutions of bismuth nitrate (EDTA) and potassium bromide with EDTA as complexing agent in slightly acidic medium. The films were characterized using Fourier transform infrared (FTIR) ...

  20. Application of design of experiment on electrophoretic deposition of ...

    Indian Academy of Sciences (India)

    A process for application of abrasion- or corrosion-resistant glass-ceramic coating materials on metal substrate by electrophoretic deposition technique in an aqueous medium has been described. The effects of various process parameters, e.g. coating material concentration, time of deposition, applied current, pH of the ...

  1. Structural, optical and electrical properties of chemically deposited ...

    Indian Academy of Sciences (India)

    Thin Films Volume 29 Issue 5 October 2006 pp 529-534 ... Copper indium diselenide; thin films; chemical bath deposition; non-stoichiometry. Abstract. Thin films of copper indium diselenide (CIS) were prepared by chemical bath deposition technique onto glass substrate at temperature, 60°C. The studies on composition, ...

  2. Electrical Conductivity of CUXS Thin Film Deposited by Chemical ...

    African Journals Online (AJOL)

    Thin films of CuxS have successfully been deposited on glass substrates using the Chemical Bath Deposition (CBD) technique. The films were then investigated for their electrical properties. The results showed that the electrical conductivities of the CuxS films with different molarities (n) of thiourea (Tu), determined using ...

  3. Uranium deposits through time

    International Nuclear Information System (INIS)

    Derry, D.R.

    1980-01-01

    The distribution of different types of uranium deposits through geological time has been noted by various authors, especially as affecting deposits formed in the Precambrian era. While this is significant, it may have been oversimplified by grouping deposits within geological time limits that are very extensive when compared with Phanerozoic groupings. As more detailed information becomes available, we find that some of the higher-grade deposits have complicated histories involving several stages of concentration separated by long periods of time. A comparison of the proportion of uranium production and reserves contributed by individual classes (and geological ages) of deposits shows a changing trend in favour of the unconformity class. Possibly more attention should be paid to metallographic uranium areas and their localizations. Some areas, e.g. Gabon, West Africa and Baker Lake, N.W.T., have more than one type of uranium deposit. A further consideration is that much of the known uranium reserves in the non-Communist world lies within a dozen areas, each ranging between 3000 and 130 000 km 2 . It is possible that such uranium metallographic areas were localized by very ancient fracture systems, now not easily recognized, in the original Earth's crust

  4. Precambrian Sulphide Deposits

    Science.gov (United States)

    Doe, Bruce R.

    1984-04-01

    This book is dedicated to Howard S. Robinson, who was born and educated in the United States, but who spent his professional career in Canada with McIntyre Porcupine Mines, concentrating on Precambrian mineral deposits. Although his career in mineral exploration was distinguished, his major contribution to earth science was probably as one of the founders of the Geological Association of Canada, an institution to which he made a bequest in his will. With this background, the strong emphasis on Canadian Precambrian mineral deposits should come as no surprise; of the 23 papers in this book, 21 are solely or primarily devoted to Canadian deposits. The two exceptions—those describing the Balmat, N.Y., zinc mines (at times the largest zinc producer in the United States) and the Crandon, Wisconsin, volcanogenic zinc-copper massive-sulfide deposit (the largest deposit of its kind found in the 1970s)—are each within a couple of hundred kilometers of the Canadian border. Although the title of the book is more expansive than the actual topics discussed, Canada is rich in Precambrian rocks and ore bodies, and Canadian scientists have been especially alert to tectonic influences in the formation of mineral deposits. These features, plus the fact that the country contains a very well exposed expanse of Archean rocks which is the largest in the world, facilitate the study of early crustal evolution and make the book of particular interest to geophysicists.

  5. Gemstone deposits of Serbia

    Directory of Open Access Journals (Sweden)

    Miladinović Zoran

    2016-06-01

    Full Text Available Gemstone minerals in Serbia have never been regarded as an interesting and significant resource. Nevertheless, more than 150 deposits and occurrences have been recorded and some of them preliminarily explored in the last 50 years. The majority of deposits and occurrences are located within the Serbo-Macedonian metallogenic province and the most significant metallogenic units at the existing level of knowledge are the Fruska Gora ore district, Cer ore district, Sumadija metallogenic zone, Kopaonik metallogenic zone and Lece-Halkidiki metallogenic zone. The most important genetic type of deposits is hydrothermal, particularly in case of serpentinite/peridotite as host/parent rock. Placer deposits are also economically important. The dominant gemstones are silica minerals: chalcedony (Chrysoprase, carnelian, bluish chalcedony etc., jasper (picture, landscape, red etc., common opal (dendritic, green, milky white etc., silica masses (undivided, and quartz (rock crystal, amethyst etc.. Beside silica minerals significant gemstones in Serbia include also beryl (aquamarine, garnet (almandine and pyrope, tourmaline, fluorite, rhodochrosite, carbonate-silica breccia, carbonate-silica onyx, silicified wood, howlite, serpentinite, marble onyx, and kyanite. This paper aims to present an overview of Serbian gemstone deposits and occurrences and their position based on a simplified gemstone metallogenic map of Serbia, as well as genetic-industrial classification of gemstone deposits and gemstone varieties.

  6. Gemstone deposits of Serbia

    Science.gov (United States)

    Miladinović, Zoran; Simić, Vladimir; Jelenković, Rade; Ilić, Miloje

    2016-06-01

    Gemstone minerals in Serbia have never been regarded as an interesting and significant resource. Nevertheless, more than 150 deposits and occurrences have been recorded and some of them preliminarily explored in the last 50 years. The majority of deposits and occurrences are located within the Serbo-Macedonian metallogenic province and the most significant metallogenic units at the existing level of knowledge are the Fruska Gora ore district, Cer ore district, Sumadija metallogenic zone, Kopaonik metallogenic zone and Lece-Halkidiki metallogenic zone. The most important genetic type of deposits is hydrothermal, particularly in case of serpentinite/peridotite as host/parent rock. Placer deposits are also economically important. The dominant gemstones are silica minerals: chalcedony (Chrysoprase, carnelian, bluish chalcedony etc.), jasper (picture, landscape, red etc.), common opal (dendritic, green, milky white etc.), silica masses (undivided), and quartz (rock crystal, amethyst etc.). Beside silica minerals significant gemstones in Serbia include also beryl (aquamarine), garnet (almandine and pyrope), tourmaline, fluorite, rhodochrosite, carbonate-silica breccia, carbonate-silica onyx, silicified wood, howlite, serpentinite, marble onyx, and kyanite. This paper aims to present an overview of Serbian gemstone deposits and occurrences and their position based on a simplified gemstone metallogenic map of Serbia, as well as genetic-industrial classification of gemstone deposits and gemstone varieties.

  7. Uranium deposits in Africa

    International Nuclear Information System (INIS)

    Wilpolt, R.H.; Simov, S.D.

    1979-01-01

    Africa is not only known for its spectacular diamond, gold, copper, chromium, platinum and phosphorus deposits but also for its uranium deposits. At least two uranium provinces can be distinguished - the southern, with the equatorial sub-province; and the south Saharan province. Uranium deposits are distributed either in cratons or in mobile belts, the first of sandstone and quartz-pebble conglomerate type, while those located in mobile belts are predominantly of vein and similar (disseminated) type. Uranium deposits occur within Precambrian rocks or in younger platform sediments, but close to the exposed Precambrian basement. The Proterozoic host rocks consist of sediments, metamorphics or granitoids. In contrast to Phanerozoic continental uranium-bearing sediments, those in the Precambrian are in marginal marine facies but they do contain organic material. The geology of Africa is briefly reviewed with the emphasis on those features which might control the distribution of uranium. The evolution of the African Platform is considered as a progressive reduction of its craton area which has been affected by three major Precambrian tectonic events. A short survey on the geology of known uranium deposits is made. However, some deposits and occurrences for which little published material is available are treated in more detail. (author)

  8. Vacuum deposited polymer/silver reflector material

    Energy Technology Data Exchange (ETDEWEB)

    Affinito, J.; Martin, P.; Gross, M.; Bennett, W.

    1994-07-01

    Weatherable, low cost, front surface, solar reflectors on flexible substrates would be highly desirable for lamination to solar concentrator panels. The method to be described in this paper may permit such reflector material to be fabricated for less than 50 cents per square foot. Vacuum deposited Polymer/Silver/Polymer reflectors and Fabry-Perot interference filters were fabricated in a vacuum web coating operation on polyester substrates. Reflectivities were measured in the wavelength range from .4 {mu}m to .8 {mu}m. It is hoped that a low cost substrate can be used with the substrate laminated to the concentrator and the weatherable acrylic polymer coating facing the sun. This technique should be capable of deposition line speeds approaching 1500 linear feet/minute. Central to this technique is a new vacuum deposition process for the high rate deposition of polymer films. This polymer process involves the flash evaporation of an acrylic monomer onto a moving substrate. The monomer is subsequently cured by an electron beam or ultraviolet light. This high speed polymer film deposition process has been named the PML process - for Polymer Multi-Layer.

  9. Microstructure of WC/C coatings deposited on steel substrates

    NARCIS (Netherlands)

    de Hosson, J.T.M.; Carvalho, N.J.M.; Brebbia, CA

    2001-01-01

    Electron microscopy, including scanning (SEM), transmission (TEM) and high-resolution (HRTEM) were employed to characterise slightly different tungsten carbide/carbon coatings deposited onto steel substrates. Complementary techniques, such as X-ray diffraction (XRD), Auger electron spectroscopy

  10. Laser chemical vapor deposition of millimeter scale three-dimensional shapes

    Science.gov (United States)

    Shaarawi, Mohammed Saad

    2001-07-01

    Laser chemical vapor deposition (LCVD) has been successfully developed as a technique to synthesize millimeter-scale components directly from the gas phase. Material deposition occurs when heat generated by the interaction of a laser beam with a substrate thermally decomposes the gas precursor. Selective illumination or scanning the laser beam over portions of a substrate forms the single thin layer of material that is the building block of this process. Sequential scanning of the laser in a pre-defined pattern on the substrate and subsequent deposit causes the layers to accumulate forming the three-dimensional shape. The primary challenge encountered in LCVD shape forming is the synthesis of uniform layers. Three deposition techniques are studied to address this problem. The most successful technique, Active Surface Deposition, is based on the premise that the most uniform deposits are created by measuring the deposition surface topology and actively varying the deposition rate in response to features at the deposition surface. Defects observed in the other techniques were significantly reduced or completely eliminated using Active Surface Deposition. The second technique, Constant Temperature Deposition, maintains deposit uniformity through the use of closed-loop modulation of the laser power to sustain a constant surface temperature during deposition. The technique was successful in depositing high quality graphite tubes >2 mm tall from an acetylene precursor and partially successful in depositing SiC + C composite tubes from tetramethylsilane (TMS). The final technique, Constant Power Deposition, is based on the premise that maintaining a uniform power output throughout deposition would result in the formation of uniform layers. Constant Power Deposition failed to form coherent shapes. Additionally, LCVD is studied using a combination of analytic and numerical models to gain insight into the deposition process. Thermodynamic modeling is used to predict the

  11. Selective Electroless Silver Deposition on Graphene Edges

    DEFF Research Database (Denmark)

    Durhuus, D.; Larsen, M. V.; Andryieuski, Andrei

    2015-01-01

    on silica substrate and thus potentially restoring electric connectivity with minimal influence on the overall graphene electrical and optical properties. The presented technique could find applications in graphene based transparent conductors as well as selective edge functionalization and can be extended......We demonstrate a method of electroless selective silver deposition on graphene edges or between graphene islands without covering the surface of graphene. Modifications of the deposition recipe allow for decoration of graphene edges with silver nanoparticles or filling holes in damaged graphene...

  12. USE OF ATOMIC LAYER DEPOSITION OF FUNCTIONALIZATION OF NANOPOROUS BIOMATERIALS

    Energy Technology Data Exchange (ETDEWEB)

    Brigmon, R.; Narayan, R.; Adiga, S.; Pellin, M.; Curtiss, L.; Stafslien, S.; Chisholm, B.; Monteiro-Riviere, N.; Elam, J.

    2010-02-08

    Due to its chemical stability, uniform pore size, and high pore density, nanoporous alumina is being investigated for use in biosensing, drug delivery, hemodialysis, and other medical applications. In recent work, we have examined the use of atomic layer deposition for coating the surfaces of nanoporous alumina membranes. Zinc oxide coatings were deposited on nanoporous alumina membranes using atomic layer deposition. The zinc oxide-coated nanoporous alumina membranes demonstrated antimicrobial activity against Escherichia coli and Staphylococcus aureus bacteria. These results suggest that atomic layer deposition is an attractive technique for modifying the surfaces of nanoporous alumina membranes and other nanostructured biomaterials.

  13. Vein type uranium deposits

    International Nuclear Information System (INIS)

    1986-01-01

    Veins are tabular- or sheet-like masses of minerals occupying or following a fracture or a set of fractures in the enclosing rock. They have been formed later than the country rock and fractures, either by filling of the open spaces or by partial or complete replacement of the adjoining rock or most commonly by both of these processes combined. This volume begins with the occurrences and deposits known from old shield areas and the sedimentary belts surrounding them. They are followed by papers describing the European deposits mostly of Variscan age, and by similar deposits known from China being of Jurassic age. The volume is completed by two papers which do not fit exactly in the given scheme. A separate abstract was prepared for each of the 25 papers in this report

  14. Mechanical characteristics of a tool steel layer deposited by using direct energy deposition

    Science.gov (United States)

    Baek, Gyeong Yun; Shin, Gwang Yong; Lee, Eun Mi; Shim, Do Sik; Lee, Ki Yong; Yoon, Hi-Seak; Kim, Myoung Ho

    2017-07-01

    This study focuses on the mechanical characteristics of layered tool steel deposited using direct energy deposition (DED) technology. In the DED technique, a laser beam bonds injected metal powder and a thin layer of substrate via melting. In this study, AISI D2 substrate was hardfaced with AISI H13 and M2 metal powders for mechanical testing. The mechanical and metallurgical characteristics of each specimen were investigated via microstructure observation and hardness, wear, and impact tests. The obtained characteristics were compared with those of heat-treated tool steel. The microstructures of the H13- and M2-deposited specimens show fine cellular-dendrite solidification structures due to melting and subsequent rapid cooling. Moreover, the cellular grains of the deposited M2 layer were smaller than those of the H13 structure. The hardness and wear resistance were most improved in the M2-deposited specimen, yet the H13-deposited specimen had higher fracture toughness than the M2-deposited specimen and heat-treated D2.

  15. Breakthrough to Non-Vacuum Deposition of Single-Crystal, Ultra-Thin, Homogeneous Nanoparticle Layers: A Better Alternative to Chemical Bath Deposition and Atomic Layer Deposition

    Directory of Open Access Journals (Sweden)

    Yu-Kuang Liao

    2017-04-01

    Full Text Available Most thin-film techniques require a multiple vacuum process, and cannot produce high-coverage continuous thin films with the thickness of a few nanometers on rough surfaces. We present a new ”paradigm shift” non-vacuum process to deposit high-quality, ultra-thin, single-crystal layers of coalesced sulfide nanoparticles (NPs with controllable thickness down to a few nanometers, based on thermal decomposition. This provides high-coverage, homogeneous thickness, and large-area deposition over a rough surface, with little material loss or liquid chemical waste, and deposition rates of 10 nm/min. This technique can potentially replace conventional thin-film deposition methods, such as atomic layer deposition (ALD and chemical bath deposition (CBD as used by the Cu(In,GaSe2 (CIGS thin-film solar cell industry for decades. We demonstrate 32% improvement of CIGS thin-film solar cell efficiency in comparison to reference devices prepared by conventional CBD deposition method by depositing the ZnS NPs buffer layer using the new process. The new ZnS NPs layer allows reduction of an intrinsic ZnO layer, which can lead to severe shunt leakage in case of a CBD buffer layer. This leads to a 65% relative efficiency increase.

  16. Breakthrough to Non-Vacuum Deposition of Single-Crystal, Ultra-Thin, Homogeneous Nanoparticle Layers: A Better Alternative to Chemical Bath Deposition and Atomic Layer Deposition.

    Science.gov (United States)

    Liao, Yu-Kuang; Liu, Yung-Tsung; Hsieh, Dan-Hua; Shen, Tien-Lin; Hsieh, Ming-Yang; Tzou, An-Jye; Chen, Shih-Chen; Tsai, Yu-Lin; Lin, Wei-Sheng; Chan, Sheng-Wen; Shen, Yen-Ping; Cheng, Shun-Jen; Chen, Chyong-Hua; Wu, Kaung-Hsiung; Chen, Hao-Ming; Kuo, Shou-Yi; Charlton, Martin D B; Hsieh, Tung-Po; Kuo, Hao-Chung

    2017-04-06

    Most thin-film techniques require a multiple vacuum process, and cannot produce high-coverage continuous thin films with the thickness of a few nanometers on rough surfaces. We present a new "paradigm shift" non-vacuum process to deposit high-quality, ultra-thin, single-crystal layers of coalesced sulfide nanoparticles (NPs) with controllable thickness down to a few nanometers, based on thermal decomposition. This provides high-coverage, homogeneous thickness, and large-area deposition over a rough surface, with little material loss or liquid chemical waste, and deposition rates of 10 nm/min. This technique can potentially replace conventional thin-film deposition methods, such as atomic layer deposition (ALD) and chemical bath deposition (CBD) as used by the Cu(In,Ga)Se₂ (CIGS) thin-film solar cell industry for decades. We demonstrate 32% improvement of CIGS thin-film solar cell efficiency in comparison to reference devices prepared by conventional CBD deposition method by depositing the ZnS NPs buffer layer using the new process. The new ZnS NPs layer allows reduction of an intrinsic ZnO layer, which can lead to severe shunt leakage in case of a CBD buffer layer. This leads to a 65% relative efficiency increase.

  17. Induced polarization and electromagnetic field surveys of sedimentary uranium deposits

    International Nuclear Information System (INIS)

    Campbell, D.L.; Smith, B.D.

    1985-01-01

    Induced polarization (IP) and electromagnetic (EM) geophysical surveys were made over three areas of sedimentary uranium deposits in the western United States. The EM techniques were sometimes useful for investigating general structural settings, but not for finding uranium deposits per se. IP techniques were useful to help pinpoint zones of disseminated pyrite associated with the uranium deposits. In one case no clear differences were seen between the IP signatures of oxidized and reduced ground. Spectral (multi-frequency) IP showed no particular advantages over conventional IP for exploration applications. A sediment mineralization factor is introduced comparable to the ''metal factor'' used to detect porphyry copper mineralization. (author)

  18. Atmospheric heavy metal deposition in Europe estimated by moss analysis

    Energy Technology Data Exchange (ETDEWEB)

    Ruehling, Aa. [Swedish Environmental Research Inst., Lund (Sweden). Dept. of Ecology

    1995-12-31

    Atmospheric heavy metal deposition in Europe including 21 countries was monitored in 1990-1992 by the moss technique. This technique is based on the fact that the concentrations of heavy metals in moss are closely correlated to atmospheric deposition. This was the first attempt to map heavy metal deposition in this large area. The objectives of the project were to characterise qualitatively and quantitatively the regional atmospheric deposition pattern of heavy metals in background areas in Europe, to indicate the location of important heavy metal pollution sources and to allow retrospective comparisons with similar studies. The present survey is a follow-up of a joint Danish and Swedish project in 1980 and an extended survey in 1985 within the framework of the Nordic Council of Ministers. In Sweden, heavy-metal deposition was first mapped on a nation-wide scale in 1968-1971 and 1975. (author)

  19. Ion-assisted deposition of thin films

    International Nuclear Information System (INIS)

    Barnett, S.A.; Choi, C.H.; Kaspi, R.; Millunchick, J.M.

    1993-01-01

    Recent work on low-energy ion-assisted deposition of epitaxial films is reviewed. Much of the recent interest in this area has been centered on the use of very low ion energies (∼ 25 eV) and high fluxes (> 1 ion per deposited atom) obtained using novel ion-assisted deposition techniques. These methods have been applied in ultra-high vacuum, allowing the preparation of high-purity device-quality semiconductor materials. The following ion-surface interaction effects during epitaxy are discussed: improvements in crystalline perfection during low temperature epitaxy, ion damage, improved homogeneity and properties in III-V alloys grown within miscibility gaps, and changes in nucleation mechanism during heteroepitaxial growth

  20. Reactive polymer fused deposition manufacturing

    Science.gov (United States)

    Kunc, Vlastimil; Rios, Orlando; Love, Lonnie J.; Duty, Chad E.; Johs, Alexander

    2017-05-16

    Methods and compositions for additive manufacturing that include reactive or thermosetting polymers, such as urethanes and epoxies. The polymers are melted, partially cross-linked prior to the depositing, deposited to form a component object, solidified, and fully cross-linked. These polymers form networks of chemical bonds that span the deposited layers. Application of a directional electromagnetic field can be applied to aromatic polymers after deposition to align the polymers for improved bonding between the deposited layers.

  1. Sputter deposition of metallic thin film and directpatterning

    Energy Technology Data Exchange (ETDEWEB)

    Ji, L.; Chen, Y.; Jiang, X.; Ji, Q.; Leung, K.-N.

    2005-09-09

    A compact apparatus is developed for deposition of metal thin film. The system employs an RF discharge plasma source with a straight RF antenna, which is made of or covered with deposition material, serving as sputtering target at the same time. The average deposition rate of copper thin film is as high as 450nm/min. By properly allocating the metal materials on the sputtering antenna, mixture deposition of multiple metal species is achieved. Using an ion beam imprinting scheme also taking advantage of ion beam focusing technique, two different schemes of direct patterning deposition process are developed: direct depositing patterned metallic thin film and resistless ion beam sputter patterning. Preliminary experiments have demonstrated direct pattern transfer from a template with feature size of micro scale; patterns with more than 10x reduction are achieved by sputtering patterning method.

  2. Electrospray ionization deposition of BSA under vacuum conditions

    Science.gov (United States)

    Hecker, Dominic; Gloess, Daniel; Frach, Peter; Gerlach, Gerald

    2015-05-01

    Vacuum deposition techniques like thermal evaporation and CVD with their precise layer control and high layer purity often cannot be applied for the deposition of chemical or biological molecules. The molecules are usually decomposed by heat. To overcome this problem, the Electrospray ionization (ESI) process known from mass spectroscopy is employed to transfer molecules into vacuum and to deposit them on a substrate. In this work, a homemade ESI tool was used to deposit BSA (Bovine serum albumin) layers with high deposition rates. Solutions with different concentrations of BSA were prepared using a methanol:water (MeOH:H2O) mixture (1:1) as solvent. The influence of the substrate distance on the deposition rate and on the transmission current was analyzed. Furthermore, the layer thickness distribution and layer adhesion were investigated.

  3. Exploring and Monitoring of Methane Hydrate Deposits

    Science.gov (United States)

    Sudac, D.; Obhođaš, J.; Nađ, K.; Valković, V.

    2018-01-01

    Relatively recently, in the last 20 years, it was discovered that methane hydrate (MH) deposits are globally distributed in the permafrost and oceans. Before 1965 when first deposits were discovered in nature, it was believed that MH can occur only in laboratory conditions or in vast parts of the Universe. Presently it is presumed that this solid crystalline compounds in which CH4 molecules occupies the water ice lattices (nominal chemical formula of MH is C4H62O23) can serve as an energy source favorably to the all of the world remaining conventional hydrocarbon sources. The worldwide estimates of MH deposits range from 2x1014 m3 to 3.053x1018 cubic meters. This uncertainty partly results from our limitations in geological understanding of the MH deposits, which is due to the relatively bad quality of data obtained by presently available seismic and electromagnetic techniques. Moreover, MH deposits can become vulnerable to climate changes, which were already occurring in geological past whit tremendous consequences for the global life on Earth. Thus, further development of advanced techniques is needed to enhance our abilities to better characterize, quantify and monitor the MH deposits. In the work presented 14 MeV neutrons and associated alpha particle imaging (API) where used to quantify the amount of MH in the sample. Samples were prepared from sea sediment, quartz sand and MH simulant. MH simulant with chemical formula C4H46O23 was made from sucrose (25 % by mass) and water. MH quantity was measured by measuring the carbon content in the sample [1-8].

  4. The structural properties of CdS deposited by chemical bath deposition and pulsed direct current magnetron sputtering

    Energy Technology Data Exchange (ETDEWEB)

    Lisco, F., E-mail: F.Lisco@lboro.ac.uk [Centre for Renewable Energy Systems Technology (CREST), School of Electronic, Electrical and Systems Engineering, Loughborough University, Leicestershire, LE11 3TU (United Kingdom); Kaminski, P.M.; Abbas, A.; Bass, K.; Bowers, J.W.; Claudio, G. [Centre for Renewable Energy Systems Technology (CREST), School of Electronic, Electrical and Systems Engineering, Loughborough University, Leicestershire, LE11 3TU (United Kingdom); Losurdo, M. [Institute of Inorganic Methodologies and of Plasmas, IMIP-CNR, via Orabona 4, 70126 Bari (Italy); Walls, J.M. [Centre for Renewable Energy Systems Technology (CREST), School of Electronic, Electrical and Systems Engineering, Loughborough University, Leicestershire, LE11 3TU (United Kingdom)

    2015-05-01

    Cadmium sulphide (CdS) thin films were deposited by two different processes, chemical bath deposition (CBD), and pulsed DC magnetron sputtering (PDCMS) on fluorine doped-tin oxide coated glass to assess the potential advantages of the pulsed DC magnetron sputtering process. The structural, optical and morphological properties of films obtained by CBD and PDCMS were investigated using X-ray photoelectron spectroscopy, X-ray diffraction, scanning and transmission electron microscopy, spectroscopic ellipsometry and UV-Vis spectrophotometry. The as-grown films were studied and comparisons were drawn between their morphology, uniformity, crystallinity, and the deposition rate of the process. The highest crystallinity is observed for sputtered CdS thin films. The absorption in the visible wavelength increased for PDCMS CdS thin films, due to the higher density of the films. The band gap measured for the as-grown CBD-CdS is 2.38 eV compared to 2.34 eV for PDCMS-CdS, confirming the higher density of the sputtered thin film. The higher deposition rate for PDCMS is a significant advantage of this technique which has potential use for high rate and low cost manufacturing. - Highlights: • Pulsed DC magnetron sputtering (PDCMS) of CdS films • Chemical bath deposition of CdS films • Comparison between CdS thin films deposited by chemical bath and PDCMS techniques • High deposition rate deposition for PDCMS deposition • Uniform, pinhole free CdS thin films.

  5. Multifunctional patchy particles by glancing angle deposition.

    Science.gov (United States)

    Pawar, Amar B; Kretzschmar, Ilona

    2009-08-18

    The application of glancing angle deposition (GLAD) as a means to produce a variety of multifunctional patchy particles is reported. The GLAD technique has been previously used to produce anisotropic particles with an anisotropy dimension of "patchiness". Here, we extend the technique to produce multifunctional patchy particles with anisotropy dimensions of "patchiness", "branching", and "chemical ordering". To access the entire particle surface, a particle stamping technique is employed using a polydimethylsiloxane (PDMS) stamp. The particle stamping technique along with GLAD yields multifunctional patchy particles having patches on opposite poles. The potential of the developed techniques in producing a wide variety of surface-anisotropic particles with variable patch size, shape, and orientation is demonstrated.

  6. Modification of thin film properties by ion bombardment during deposition

    International Nuclear Information System (INIS)

    Harper, J.M.E.; Cuomo, J.J.; Gambino, R.J.; Kaufman, H.R.

    1984-01-01

    Many thin film deposition techniques involve some form of energetic particle bombardment of the growing film. The degree of bombardment greatly influences the film composition, structure and other properties. While in some techniques the degree of bombardment is secondary to the original process design, in recent years more deposition systems are being designed with the capability for controlled ion bombardment of thin films during deposition. The highest degree of control is obtained with ion beam sources which operate independently of the vapor source providing the thin film material. Other plasma techniques offer varying degrees of control of energetic particle bombardment. Deposition methods involving ion bombardment are described, and the basic processes with which film properties are modified by ion bombardment are summarized. (Auth.)

  7. Chemical vapor deposition of cadmium tellurium films for photovoltaic devices

    International Nuclear Information System (INIS)

    Chu, S.S.; Chu, T.L.; Han, K.D.; Liu, Y.Z.; Mantravadi, M.

    1987-01-01

    Cadmium telluride films have been deposited by chemical vapor deposition (CVD) and close-spaced sublimation (CSS), and their structural and electrical properties have been characterized in detail. The CVD technique has the advantage of controlling the electrical resistivity of p-CdTe films while the CST technique is capable of depositing p-CdTe films at high rates. Thin film heterojunction solar cells of the configuration p-CdTe/CdS/SnO/sub 2/:F/glass have been prepared by the deposition techniques. Solar cells of 1 cm/sup 2/ or larger in area with AM1.5 (global) efficiency of 10.5% have been prepared

  8. Effect of deposition temperature on the structural, morphological and optical band gap of lead selenide thin films synthesized by chemical bath deposition method

    Energy Technology Data Exchange (ETDEWEB)

    Hone, Fekadu Gashaw, E-mail: fekeye@gmail.com [Hawassa University, Department of Physics, Hawassa (Ethiopia); Ampong, Francis Kofi [Kwame Nkrumah University of Science and Technology, Department of Physics, Kumasi (Ghana)

    2016-11-01

    Lead selenide (PbSe) nanocrystalline thin films have been deposited on silica glass substrates by the chemical bath deposition technique. The samples were deposited at the bath temperatures of 60, 75 and 90 °C respectively and characterized by a variety of techniques. The XRD results revealed that the PbSe thin film deposited at 60 °C was amorphous in nature. Films deposited at higher temperatures exhibited sharp and intense diffraction peaks, indicating an improvement in crystallinety. The deposition temperature also had a strong influence on the preferred orientation of the crystallites as well as other structural parameters such as microstrain and dislocation density. From the SEM study it was observed that film deposited at 90 °C had well defined crystallites, uniformly distributed over the entire surface of the substrate. The EDAX study confirmed that the samples deposited at the higher temperature had a better stoichiometric ratio. The optical band gap varied from 2.26 eV to 1.13 eV with increasing deposition temperature. - Highlights: • The crystallinety of the films improved as the deposition temperature increased. • The deposition temperature strongly influenced the preferred orientations. • Microstrain and dislocation density are decreased linearly with deposition temperature. • Band gap decreased from 2.26 eV to 1.13 eV as the deposition temperature increased.

  9. Quantitative measurement of aerosol deposition on skin, hair and clothing for dosimetric assessment. Final report

    DEFF Research Database (Denmark)

    Fogh, C.L.; Byrne, M.A.; Andersson, Kasper Grann

    1999-01-01

    the deposition and subsequent fate of contaminant aerosol on skin, hair and clothing. The main technique applied involves the release and subsequent deposition on volunteers in test rooms of particles of differentsizes labelled with neutron activatable rare earth tracers. Experiments indicate that the deposition...

  10. Ultrashort pulse laser deposition of thin films

    Science.gov (United States)

    Perry, Michael D.; Banks, Paul S.; Stuart, Brent C.

    2002-01-01

    Short pulse PLD is a viable technique of producing high quality films with properties very close to that of crystalline diamond. The plasma generated using femtosecond lasers is composed of single atom ions with no clusters producing films with high Sp.sup.3 /Sp.sup.2 ratios. Using a high average power femtosecond laser system, the present invention dramatically increases deposition rates to up to 25 .mu.m/hr (which exceeds many CVD processes) while growing particulate-free films. In the present invention, deposition rates is a function of laser wavelength, laser fluence, laser spot size, and target/substrate separation. The relevant laser parameters are shown to ensure particulate-free growth, and characterizations of the films grown are made using several diagnostic techniques including electron energy loss spectroscopy (EELS) and Raman spectroscopy.

  11. Uranium exploration techniques in Bolivia

    International Nuclear Information System (INIS)

    Virreira, V.

    1981-01-01

    The exploration techniques used by the Bolivian Nuclear Energy Commission/Comision Boliviana de Energia Nuclear (COBOEN) in certain areas of Bolivia that are considered promising from the standpoint of uranium deposits are presented in summary form. The methods and results obtained are described, including the techniques used by the Italian company AGIP-URANIUM during four years of exploration under contract with COBOEN. Statistical data are also given explaining the present level of uranium exploration in Bolivia. (author)

  12. Visualization Techniques for Single Channel DPF Systems

    Energy Technology Data Exchange (ETDEWEB)

    Dillon, Heather E.; Maupin, Gary D.; Carlson, Shelley J.; Saenz, Natalio T.; Gallant, Thomas R.

    2007-04-01

    New techniques have been developed to visualize soot deposition in both traditional and new diesel particulate filter (DPF) substrate materials using a modified cyanoacrylate fuming technique. Loading experiments have been conducted on a variety of single channel DPF substrates to develop a deeper understanding of soot penetration, soot deposition characteristics, and to confirm modeling results. Early results indicate that stabilizing the soot layer using a vapor adhesive may allow analysis of the layer with new methods.

  13. Dismantling techniques

    International Nuclear Information System (INIS)

    Wiese, E.

    1998-01-01

    Most of the dismantling techniques used in a Decontamination and Dismantlement (D and D) project are taken from conventional demolition practices. Some modifications to the techniques are made to limit exposure to the workers or to lessen the spread of contamination to the work area. When working on a D and D project, it is best to keep the dismantling techniques and tools as simple as possible. The workers will be more efficient and safer using techniques that are familiar to them. Prior experience with the technique or use of mock-ups is the best way to keep workers safe and to keep the project on schedule

  14. Atmospheric transport, diffusion, and deposition of radioactivity

    International Nuclear Information System (INIS)

    Crawford, T.V.

    1969-01-01

    From a meteorological standpoint there are two types of initial sources for atmospheric diffusion from Plowshare applications. One is the continuous point-source plume - a slow, small leak from an underground engineering application. The other is the large cloud produced almost instantaneously from a cratering application. For the purposes of this paper the effluent from neither type has significant fall speed. Both are carried by the prevailing wind, but the statistics of diffusion for each type are different. The use of constant altitude, isobaric and isentropic techniques for predicting the mean path of the effluent is briefly discussed. Limited data are used to assess the accuracy of current trajectory forecast techniques. Diffusion of continuous point-source plumes has been widely studied; only a brief review is given of the technique used and the variability of their results with wind speed and atmospheric stability. A numerical model is presented for computing the diffusion of the 'instantaneously-produced' large clouds. This model accounts for vertical and diurnal changes in atmospheric turbulence, wet and dry deposition, and radioactivity decay. Airborne concentrations, cloud size, and deposition on the ground are calculated. Pre- and post-shot calculations of cloud center, ground level concentration of gross radioactivity, and dry and wet deposition of iodine-131 are compared with measurements on Cabriolet and Buggy. (author)

  15. Chemical vapor deposition (CVD) of uranium for alpha spectrometry

    International Nuclear Information System (INIS)

    Ramirez V, M. L.; Rios M, C.; Ramirez O, J.; Davila R, J. I.; Mireles G, F.

    2015-09-01

    The uranium determination through radiometric techniques as alpha spectrometry requires for its proper analysis, preparation methods of the source to analyze and procedures for the deposit of this on a surface or substrate. Given the characteristics of alpha particles (small penetration distance and great loss of energy during their journey or its interaction with the matter), is important to ensure that the prepared sources are thin, to avoid problems of self-absorption. The routine methods used for this are the cathodic electro deposition and the direct evaporation, among others. In this paper the use of technique of chemical vapor deposition (CVD) for the preparation of uranium sources is investigated; because by this, is possible to obtain thin films (much thinner than those resulting from electro deposition or evaporation) on a substrate and comprises reacting a precursor with a gas, which in turn serves as a carrier of the reaction products to achieve deposition. Preliminary results of the chemical vapor deposition of uranium are presented, synthesizing and using as precursor molecule the uranyl acetylacetonate, using oxygen as carrier gas for the deposition reaction on a glass substrate. The uranium films obtained were found suitable for alpha spectrometry. The variables taken into account were the precursor sublimation temperatures and deposition temperature, the reaction time and the type and flow of carrier gas. Of the investigated conditions, two depositions with encouraging results that can serve as reference for further work to improve the technique presented here were selected. Alpha spectra obtained for these depositions and the characterization of the representative samples by scanning electron microscopy and X-ray diffraction are also presented. (Author)

  16. Pulsed laser deposition of Tl-Ca-Ba-Cu-O films

    International Nuclear Information System (INIS)

    Ianno, N.J.; Liou, S.H.; Woollam, J.A.; Thompson, D.; Johs, B.

    1990-01-01

    Pulsed laser deposition is a technique commonly used to deposit high quality thin films of high temperature superconductors. This paper discusses the results obtained when this technique is applied to the deposition of Tl-Ca-Ba-Cu-O thin films using a frequency doubled Nd:YAG laser operating at 532 nm and an excimer laser operating at 248 nm. Films with onset temperatures of 125 K and zero resistance temperatures of 110 K deposited on (100) oriented MgO from a composite Tl2Ca2Ba2Cu3Ox target were obtained at both wavelengths upon appropriate post deposition annealing. Films deposited at 532 nm exhibit a rough surface, while those deposited at 248 nm are smooth and homogeneous. Upon annealing, films deposited at both wavelengths are single phase Tl2Ca2Ba2Cu3Ox. 12 refs

  17. Deposition and post-processing techniques for transparent conductive films

    Energy Technology Data Exchange (ETDEWEB)

    Christoforo, Mark Greyson; Mehra, Saahil; Salleo, Alberto; Peumans, Peter

    2017-07-04

    In one embodiment, a method is provided for fabrication of a semitransparent conductive mesh. A first solution having conductive nanowires suspended therein and a second solution having nanoparticles suspended therein are sprayed toward a substrate, the spraying forming a mist. The mist is processed, while on the substrate, to provide a semitransparent conductive material in the form of a mesh having the conductive nanowires and nanoparticles. The nanoparticles are configured and arranged to direct light passing through the mesh. Connections between the nanowires provide conductivity through the mesh.

  18. Uranium deposits of Zaire

    International Nuclear Information System (INIS)

    Kitmut, D.; Malu wa Kalenga

    1979-01-01

    Since April 1960, following the closing of the Shinkolobwe mine, the Republic of Zaire has ceased to be a producer of uranium. Nevertheless, Gecamines (Generale des carrieres et mines du Zaire), a wholly state-owned company, is continuing its research on uranium occurrences which have been discovered in its concession in the course of aerial radiometric prospecting. The most recent campaign was the one carried out in 1969 and 1972 by Hunting Company. On-the-ground verification of these shows has not yet resulted in the discovery of a workable deposit. There are other sectors cutting across Zaire which might well contain uranium deposits: this is true of the sedimentary phosphates of the region of Lower Zaire as well as of the frontier region between Zaire and the Central African Empire. However, no detailed exploration work has yet been carried out. (author)

  19. Background and survey of bioreplication techniques.

    Science.gov (United States)

    Pulsifer, Drew Patrick; Lakhtakia, Akhlesh

    2011-09-01

    Bioreplication is the direct reproduction of a biological structure in order to realize at least one specific functionality. Current bioreplication techniques include the sol-gel technique, atomic layer deposition, physical vapor deposition, and imprint lithography and casting. The combined use of a focused ion beam and a scanning electron microscope could develop into a bioreplication technique as well. Some of these techniques are more suitable for reproducing surface features, others for bulk three-dimensional structures. Industrial upscaling appears possible only for imprint lithography and casting (which can be replaced by stamping).

  20. Thorium ore deposits

    International Nuclear Information System (INIS)

    Angelelli, Victorio.

    1984-01-01

    The main occurences of the thorium minerals of the Argentine Republic which have not been exploited, due to their reduced volume, are described. The thoriferous deposits have three genetic types: pegmatitic, hydrothermal and detritic, being the most common minerals: monazite, thorite and thorogummite. The most important thorium accumulations are located in Salta, being of less importance those of Cordoba, Jujuy and San Juan. (M.E.L.) [es

  1. Short review on chemical bath deposition of thin film and characterization

    Energy Technology Data Exchange (ETDEWEB)

    Mugle, Dhananjay, E-mail: dhananjayforu@gmail.com; Jadhav, Ghanshyam, E-mail: ghjadhav@rediffmail.com [Depertment of Physics, Shri Chhatrapati Shivaji College, Omerga-413606 (India)

    2016-05-06

    This reviews the theory of early growth of the thin film using chemical deposition methods. In particular, it critically reviews the chemical bath deposition (CBD) method for preparation of thin films. The different techniques used for characterizations of the chemically films such as X-ray diffractometer (XRD), Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), Electrical conductivity and Energy Dispersive Spectroscopy (EDS) are discussed. Survey shows the physical and chemical properties solely depend upon the time of deposition, temperature of deposition.

  2. Pulse plating of nickel deposits

    Energy Technology Data Exchange (ETDEWEB)

    Stimetz, C.J.; Stevenson, M.F.

    1980-02-01

    Pulse plated and conventional nickel deposits have been compared for differences in morphology, mechanical properties, and microstructure. The deposits were obtained from nickel sulfamate, nickel chloride, and Watts nickel plating solutions. No significant differences were found in the direct and pulse current deposits from the sulfamate and chloride solutions; however, significant differences in microstructure, yield strength, and microhardness were observed in deposits from the Watts nickel solution.

  3. Geology of hydrothermal uranium deposits

    International Nuclear Information System (INIS)

    Korolev, K.G.; Belov, V.K.; Putilov, G.S.

    1983-01-01

    Geological characteristics of hydrothermal phosphorus-uranium deposits placed in sedimentary, igneous-sedimentary, metamorphic and intrusion formations are presented. Attention is paid to mineral composition, texture and structure of ores, their genesis, tectonics. Geochemical peculiarities of ores and age of molybdenum-uranium and uranium deposits are described. Geological criteria and prospecting features of uranium and uranium-molybdenum deposits are given

  4. The classification of minerals deposits

    International Nuclear Information System (INIS)

    Khasanov, A.Kh.

    1988-01-01

    In this part of book author present the classification of minerals deposits. Deposit formation take place as a result of complicated and long geology processes in the wide temperature intervals (from 1500 d ig C to usual) and pressures (from usual and to tens kilobars). Deposits of minerals as other investigation objects require in definite systematization on the base of definite characteristics

  5. Effect of a reducing agent for silver on the electrochemical activity of an Ag/Ba{sub 0.5}Sr{sub 0.5}Co{sub 0.8}Fe{sub 0.2}O{sub 3-{delta}} electrode prepared by electroless deposition technique

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Wei; Ran, Ran; Cai, Rui; Shao, Zongping; Jin, Wanqin; Xu, Nanping [State Key Laboratory of Materials-Oriented Chemical Engineering, College of Chemistry and Chemical Engineering, Nanjing University of Technology, No. 5 Xin Mofan Road, Nanjing 210009 (China)

    2009-01-15

    Silver-modified Ba{sub 0.5}Sr{sub 0.5}Co{sub 0.8}Fe{sub 0.2}O{sub 3-{delta}} (Ag/BSCF) electrodes were prepared using an electroless deposition technique. The morphology, microstructure and oxygen reduction reaction activity of the resulted Ag/BSCF electrodes were comparatively studied using Fourier transform infrared spectra, environmental scanning electron microscopy, temperature-programmed oxygen desorption, X-ray diffraction, and electrochemical impedance spectroscopy. An area-specific resistance as low as 0.038 {omega} cm{sup 2} was achieved for N{sub 2}H{sub 4}-reduced Ag/BSCF cathode at 600 C. Carbonates were detected over the BSCF surface during the reduction of silver, which deteriorated both the charge-transfer process and diffusion process of HCHO-reduced Ag/BSCF cathode for the oxygen electrochemical reduction reaction. An anode-supported single cell with an N{sub 2}H{sub 4}-reduced Ag/BSCF cathode showed a peak power of 826 mW cm{sup -2} at 600 C. In comparison, only 672 mW cm{sup -2} was observed with the HCHO-reduced Ag/BSCF cathode. (author)

  6. Morphology evolution in spinel manganite films deposited from an aqueous solution

    International Nuclear Information System (INIS)

    Ko, Song Won; Li, Jing; Trolier-McKinstry, Susan

    2012-01-01

    Spinel manganite films were deposited by the spin spray technique at low deposition temperatures ( 1000, agglomeration of small particles was dominant, which suggests that homogeneous nucleation is dominant during deposition. Heterogeneous nucleation was critical to obtain dense films. - Highlights: ► Film microstructure depends on supersaturation. ► Heterogeneous nucleation induces dense and continuous films. ► The spin spray technique enables use of a variety of substrates.

  7. Pure and Sn-doped ZnO films produced by pulsed laser deposition

    DEFF Research Database (Denmark)

    Holmelund, E.; Schou, Jørgen; Tougaard, S.

    2002-01-01

    A new technique, metronome doping, has been used for doping of films during pulsed laser deposition (PLD). This technique makes it possible to dope continuously during film growth with different concentrations of a dopant in one deposition sequence. Films of pure and doped ZnO have been produced...

  8. Handbook of laboratory techniques

    International Nuclear Information System (INIS)

    2002-01-01

    The Nuclear Regulatory Authority in Argentina have laboratories of support to regulations functions on radiological and nuclear safety, safeguards and physical protection, that have a surface of 2950 m 2 in the Ezeiza Atomic Center. The manual describes in seven chapters the different techniques developed and applied in the laboratories along four decades of existence. The chapter 1: Dedicated to the treatment of environmental samples, described the procedures associated with the different types of samples: deposits, waters, sediments, vegetables, milk, fish and diet. The chapter 2: Details 48 radiochemical techniques associated to the measurements of americium 241, carbon 16, strontium 90, iodine 129, plutonium, radium 226, radon, uranium, nickel and actinides. The chapter 3: Describes the measurements techniques of alpha and gamma spectrometry. The different techniques of biological and physical dosimetry are described in the chapters 5 and 6 respectively. The final chapter is dedicated the techniques of external and internal contamination. It s important to emphasize that this manual contains the standardized technologies that the Nuclear Regulatory Authority of Argentina submits regularly to international comparisons

  9. Acquired Techniques

    DEFF Research Database (Denmark)

    Lunde Nielsen, Espen; Halse, Karianne

    2013-01-01

    Acquired Techniques - a Leap into the Archive, at Aarhus School of Architecture. In collaboration with Karianne Halse, James Martin and Mika K. Friis. Following the footsteps of past travelers this is a journey into tools and techniques of the architectural process. The workshop will focus upon...

  10. Air and deposition

    International Nuclear Information System (INIS)

    Kiesewetter, W.

    1985-01-01

    The Deutscher Wetterdienst (German Weather Service) was given the task in 1961 to act as the directing centre for air and deposition monitoring in the FRG, which primarily meant fallout and atmospheric radioactivity monitoring over the territory of the FRG. In addition, the Bundesamt fuer Zivilschutz (Federal Office for Civil Defence) since 1960 specialized in measuring and monitoring the fission product Kr-85 in the atmosphere. The interlaboratory comparisons and analyses made every year for various radionuclides guarantee early detection of changes in the level of airborne environmental radioactivity. (DG) [de

  11. Uranium ore deposits

    International Nuclear Information System (INIS)

    Angelelli, Victorio.

    1984-01-01

    The main uranium deposits and occurrences in the Argentine Republic are described, considering, in principle, their geologic setting, the kind of 'model' of the mineralization and its possible origin, and describing the ore species present in each case. The main uraniferous accumulations of the country include the models of 'sandstong type', veintype and impregnation type. There are also other kinds of accumulations, as in calcrete, etc. The main uranium production has been registered in the provinces of Mendoza, Salta, La Rioja, Chubut, Cordoba and San Luis. In each case, the minerals present are mentioned, having been recognized 37 different species all over the country (M.E.L.) [es

  12. Deposition dynamics of multi-solvent bioinks

    Science.gov (United States)

    Kaneelil, Paul; Pack, Min; Cui, Chunxiao; Han, Li-Hsin; Sun, Ying

    2017-11-01

    Inkjet printing cellular scaffolds using bioinks is gaining popularity due to the advancement of printing technology as well as the growing demands of regenerative medicine. Numerous studies have been conducted on printing scaffolds of biomimetic structures that support the cell production of human tissues. However, the underlying physics of the deposition dynamics of bioinks remains elusive. Of particular interest is the unclear deposition dynamics of multi-solvent bioinks, which is often used to tune the micro-architecture formation. Here we systematically studied the effects of jetting frequency, solvent properties, substrate wettability, and temperature on the three-dimensional deposition patterns of bioinks made of Methacrylated Gelatin and Carboxylated Gelatin. The microflows inside the inkjet-printed picolitre drops were visualized using fluorescence tracer particles to decipher the complex processes of multi-solvent evaporation and solute self-assembly. The evolution of droplet shape was observed using interferometry. With the integrated techniques, the interplay of solvent evaporation, biopolymer deposition, and multi-drop interactions were directly observed for various ink and substrate properties, and printing conditions. Such knowledge enables the design and fabrication of a variety of tissue engineering scaffolds for potential use in regenerative medicine.

  13. An Introduction to Atomic Layer Deposition with Thermal Applications

    Science.gov (United States)

    Dwivedi, Vivek H.

    2015-01-01

    Atomic Layer Deposition (ALD) is a cost effective nano-manufacturing technique that allows for the conformal coating of substrates with atomic control in a benign temperature and pressure environment. Through the introduction of paired precursor gases thin films can be deposited on a myriad of substrates ranging from glass, polymers, aerogels, and metals to high aspect ratio geometries. This talk will focus on the utilization of ALD for engineering applications.

  14. New tools to investigate textures of pyroclastic deposits

    Energy Technology Data Exchange (ETDEWEB)

    Sarocchi, Damiano [Instituto de GeologIa / Fac. IngenierIa UASLP, Dr. M. Nava No 5, Zona Universitaria 78240, San Luis PotosI (Mexico); Borselli, Lorenzo [Istituto di Ricerca per la Protezione Idrogeologica, Consiglio Nazionale delle Ricerche, Via Madonna del Piano 10, 50019, Sesto Fiorentino (Italy); MacIas, Jose Luis [Departamento de VulcanologIa, Instituto de Geofisica, Universidad Nacional Autonoma de Mexico, Coyoacan 04510, D.F. (Mexico)

    2008-10-01

    A pyroclastic flow deposit keeps a fingerprint of the physical processes that occurred in the flow during transport and settling. Part of this information is recorded in the texture of the deposit offering an instantaneous view of the flow prior to freezing. In this work we introduce some texture's analysis techniques, based on image analysis, that we have developed or tuned during the last years.

  15. Experiment and equipment of depositing diamond films with CVD system

    International Nuclear Information System (INIS)

    Xie Erqing; Song Chang'an

    2002-01-01

    CVD (chemical vapor deposition) emerged in recent years is a new technique for thin film deposition, which play a key role in development of modern physics. It is important to predominate the principle and technology of CVD for studying modern physics. In this paper, a suit of CVD experimental equipment for teaching in college physics is presented, which has simple design and low cost. The good result was gained in past teaching practices

  16. Variable fused deposition modelling - concept design and tool path generation

    OpenAIRE

    Brooks, Hadley Laurence

    2011-01-01

    Current Fused Deposition Modelling (FDM) techniques use fixed diameter nozzles to deposit a filament of plastic layer by layer. The consequence is that the same small nozzle, essential for fine details, is also used to fill in relatively large volumes. In practice a Pareto-optimal nozzle diameter is chosen that attempts to maximise resolution while minimising build time. This paper introduces a concept for adapting an additive manufacturing system, which exploits a variable diameter nozzle fo...

  17. Fabrication and evaluation of chemically vapor deposited tungsten heat pipe.

    Science.gov (United States)

    Bacigalupi, R. J.

    1972-01-01

    A network of lithium-filled tungsten heat pipes is being considered as a method of heat extraction from high temperature nuclear reactors. The need for material purity and shape versatility in these applications dictates the use of chemically vapor deposited (CVD) tungsten. Adaptability of CVD tungsten to complex heat pipe designs is shown. Deposition and welding techniques are described. Operation of two lithium-filled CVD tungsten heat pipes above 1800 K is discussed.

  18. Nickel-cobalt laterites: a deposit model: Chapter H in Mineral deposit models for resource assessment

    Science.gov (United States)

    Marsh, Erin; Anderson, Eric J.; Gray, Floyd

    2013-01-01

    Nickel-cobalt (Ni-Co) laterite deposits are supergene enrichments of Ni±Co that form from intense chemical and mechanical weathering of ultramafic parent rocks. These regolith deposits typically form within 26 degrees of the equator, although there are a few exceptions. They form in active continental margins and stable cratonic settings. It takes as little as one million years for a laterite profile to develop. Three subtypes of Ni-Co laterite deposits are classified according to the dominant Ni-bearing mineralogy, which include hydrous magnesium (Mg)-silicate, smectite, and oxide. These minerals form in weathering horizons that begin with the unweathered protolith at the base, saprolite next, a smectite transition zone only in profiles where drainage is very poor, followed by limonite, and then capped with ferricrete at the top. The saprolite contains Ni-rich hydrous Mg-silicates, the Ni-rich clays occur in the transition horizon, and Ni-rich goethite occurs in the limonite. Although these subtypes of deposits are the more widely used terms for classification of Ni-Co laterite deposits, most deposits have economic concentrations of Ni in more than one horizon. Because of their complex mineralogy and heterogeneous concentrations, mining of these metallurgically complex deposits can be challenging. Deposits range in size from 2.5 to about 400 million tonnes, with Ni and Co grades of 0.66–2.4 percent (median 1.3) and 0.01–0.15 percent (median 0.08), respectively. Modern techniques of ore delineation and mineralogical identification are being developed to aid in streamlining the Ni-Co laterite mining process, and low-temperature and low-pressure ore processing techniques are being tested that will treat the entire weathered profile. There is evidence that the production of Ni and Co from laterites is more energy intensive than that of sulfide ores, reflecting the environmental impact of producing a Ni-Co laterite deposit. Tailings may include high levels of

  19. Patterned electrochemical deposition of copper using an electron beam

    Directory of Open Access Journals (Sweden)

    Mark den Heijer

    2014-02-01

    Full Text Available We describe a technique for patterning clusters of metal using electrochemical deposition. By operating an electrochemical cell in the transmission electron microscope, we deposit Cu on Au under potentiostatic conditions. For acidified copper sulphate electrolytes, nucleation occurs uniformly over the electrode. However, when chloride ions are added there is a range of applied potentials over which nucleation occurs only in areas irradiated by the electron beam. By scanning the beam we control nucleation to form patterns of deposited copper. We discuss the mechanism for this effect in terms of electron beam-induced reactions with copper chloride, and consider possible applications.

  20. Steam generator deposit control program assessment at Comanche Peak

    International Nuclear Information System (INIS)

    Stevens, J.; Fellers, B.; Orbon, S.

    2002-01-01

    Comanche Peak has employed a variety of methods to assess the effectiveness of the deposit control program. These include typical methods such as an extensive visual inspection program and detailed corrosion product analysis and trending. In addition, a recently pioneered technique, low frequency eddy current profile analysis (LFEC) has been utilized. LFEC provides a visual mapping of the magnetite deposit profile of the steam generator. Analysis of the LFEC results not only provides general area deposition rates, but can also provide local deposition patterns, which is indicative of steam generator performance. Other techniques utilized include trending of steam pressure, steam generator hideout-return, and flow assisted corrosion (FAC) results. The sum of this information provides a comprehensive assessment of the deposit control program effectiveness and the condition of the steam generator. It also provides important diagnostic and predictive information relative to steam generator life management and mitigative strategies, such as special cleaning procedures. This paper discusses the techniques employed by Comanche Peak Chemistry to monitor the effectiveness of the deposit control program and describes how this information is used in strategic planning. (authors)

  1. FDIC Summary of Deposits (SOD) Download File

    Data.gov (United States)

    Federal Deposit Insurance Corporation — The FDIC's Summary of Deposits (SOD) download file contains deposit data for branches and offices of all FDIC-insured institutions. The Federal Deposit Insurance...

  2. Atomic layer deposition of copper thin film and feasibility of deposition on inner walls of waveguides

    Science.gov (United States)

    Yuqing, XIONG; Hengjiao, GAO; Ni, REN; Zhongwei, LIU

    2018-03-01

    Copper thin films were deposited by plasma-enhanced atomic layer deposition at low temperature, using copper(I)-N,N‧-di-sec-butylacetamidinate as a precursor and hydrogen as a reductive gas. The influence of temperature, plasma power, mode of plasma, and pulse time, on the deposition rate of copper thin film, the purity of the film and the step coverage were studied. The feasibility of copper film deposition on the inner wall of a carbon fibre reinforced plastic waveguide with high aspect ratio was also studied. The morphology and composition of the thin film were studied by atomic force microscopy and x-ray photoelectron spectroscopy, respectively. The square resistance of the thin film was also tested by a four-probe technique. On the basis of on-line diagnosis, a growth mechanism of copper thin film was put forward, and it was considered that surface functional group played an important role in the process of nucleation and in determining the properties of thin films. A high density of plasma and high free-radical content were helpful for the deposition of copper thin films.

  3. MALDI imaging of lipids after matrix sublimation/deposition.

    Science.gov (United States)

    Murphy, Robert C; Hankin, Joseph A; Barkley, Robert M; Zemski Berry, Karin A

    2011-11-01

    Mass spectrometric techniques have been developed to record mass spectra of biomolecules including lipids as they naturally exist within tissues and thereby permit the generation of images displaying the distribution of specific lipids in tissues, organs, and intact animals. These techniques are based on matrix-assisted laser desorption/ionization (MALDI) that requires matrix application onto the tissue surface prior to analysis. One technique of application that has recently shown significant advantages for lipid analysis is sublimation of matrix followed by vapor deposition directly onto the tissue. Explanations for enhanced sensitivity realized by sublimation/deposition related to sample temperature after a laser pulse and matrix crystal size are presented. Specific examples of sublimation/deposition in lipid imaging of various organs including brain, ocular tissue, and kidney are presented. Copyright © 2011 Elsevier B.V. All rights reserved.

  4. A Study of Deposition Coatings Formed by Electroformed Metallic Materials.

    Directory of Open Access Journals (Sweden)

    Shoji Hayashi

    Full Text Available Major joining methods of dental casting metal include brazing and laser welding. However, brazing cannot be applied for electroformed metals since heat treatment could affect the fit, and, therefore, laser welding is used for such metals. New methods of joining metals that do not impair the characteristics of electroformed metals should be developed. When new coating is performed on the surface of the base metal, surface treatment is usually performed before re-coating. The effect of surface treatment is clinically evaluated by peeling and flex tests. However, these testing methods are not ideal for deposition coating strength measurement of electroformed metals. There have been no studies on the deposition coating strength and methods to test electroformed metals. We developed a new deposition coating strength test for electroformed metals. The influence of the negative electrolytic method, which is one of the electrochemical surface treatments, on the strength of the deposition coating of electroformed metals was investigated, and the following conclusions were drawn: 1. This process makes it possible to remove residual deposits on the electrodeposited metal surface layer. 2. Cathode electrolysis is a simple and safe method that is capable of improving the surface treatment by adjustments to the current supply method and current intensity. 3. Electrochemical treatment can improve the deposition coating strength compared to the physical or chemical treatment methods. 4. Electro-deposition coating is an innovative technique for the deposition coating of electroformed metal.

  5. Chemical Vapour Deposition of Large Area Graphene

    DEFF Research Database (Denmark)

    Larsen, Martin Benjamin Barbour Spanget

    Chemical Vapor Deposition (CVD) is a viable technique for fabrication of large areas of graphene. CVD fabrication is the most prominent and common way of fabricating graphene in industry. In this thesis I have attempted to optimize a growth recipe and catalyst layer for CVD fabrication of uniform......, single layer, and high carrier mobility large area graphene. The main goals of this work are; (1) explore the graphene growth mechanics in a low pressure cold-wall CVD system on a copper substrate, and (2) optimize the process of growing high quality graphene in terms of carrier mobility, and crystal...... structure. Optimization of a process for graphene growth on commercially available copper foil is limited by the number of aluminium oxide particles on the surface of the catalyst. By replacing the copper foil with a thin deposited copper film on a SiO2/Si or c-plane sapphire wafer the particles can...

  6. Intensity techniques

    DEFF Research Database (Denmark)

    Jacobsen, Finn

    2008-01-01

    The Handbook of Signal Processing in Acoustics will compile the techniques and applications of signal processing as they are used in the many varied areas of Acoustics. The Handbook will emphasize the interdisciplinary nature of signal processing in acoustics. Each Section of the Handbook...... from different areas, will find the self-contained chapters accessible and will be interested in the similarities and differences between the approaches and techniques used in different areas of acoustics....

  7. Experimental reproduction of tsunami deposit

    Science.gov (United States)

    Yoshii, T.; Matsuyama, M.; Tanaka, S.

    2015-12-01

    Understanding the process of sediment transport and deposition under a tsunami inundation is essential to provide the credible information about potential tsunamis from tsunami deposits. Detections of tsunami deposit has contributed to reveal centuries-old record of tsunami incursions. However, our knowledge is still not enough for evaluating the scale of past tsunamis using deposits. In this study, a laboratory experiment was conducted to investigate the relationship between the hydraulic condition and sedimentological features of tsunami deposit. The large wave flume in CRIEPI, one of the largest wave flume in the world, which has 205 m length, 3.4 m width and 6 m depth was used. The sandy beach with uniform slope (1/50) were made in the flume. Sand dune of 0.2 high was placed near the shoreline. The tsunami was made by the wave generator which has 2.2 m stroke. The wave at the shore line has 0.6 m depth and the horizontal velocity reached up to 3.5 m/s. The incursion of the wave and its return flow completely washed out the dune and resulted in the deposition especially near the dune. The thickness of deposit shows landward thinning and fining, which has been widely confirmed by field observations. In addition, sedimentary structures of the deposit was investigated using the method similar to that used in geological survey such as core sampling and relief peel sampling. The obtained samples were investigated using a X-ray computed tomography. The obtained CT-images shows that most part of deposition consists two or more subsections divided by horizontal lamination although the deposition near the dune has drastic and complex change thickness and grain size. The subsections shows upward-fining and upward-coarsening which are been reported as common sedimentary structures of tsunami deposit from field surveys. Considering the similarity of sedimentary structures in the deposit reconstructed in this experiment and actual tsunami deposits, this experiment succeeded

  8. Respiratory trace deposition models. Final report

    International Nuclear Information System (INIS)

    Yeh, H.C.

    1980-03-01

    Respiratory tract characteristics of four mammalian species (human, dog, rat and Syrian hamster) were studied, using replica lung casts. An in situ casting techniques was developed for making the casts. Based on an idealized branch model, over 38,000 records of airway segment diameters, lengths, branching angles and gravity angles were obtained from measurements of two humans, two Beagle dogs, two rats and one Syrian hamster. From examination of the trimmed casts and morphometric data, it appeared that the structure of the human airway is closer to a dichotomous structure, whereas for dog, rat and hamster, it is monopodial. Flow velocity in the trachea and major bronchi in living Beagle dogs was measured using an implanted, subminiaturized, heated film anemometer. A physical model was developed to simulate the regional deposition characteristics proposed by the Task Group on Lung Dynamics of the ICRP. Various simulation modules for the nasopharyngeal (NP), tracheobronchial (TB) and pulmonary (P) compartments were designed and tested. Three types of monodisperse aerosols were developed for animal inhalation studies. Fifty Syrian hamsters and 50 rats were exposed to five different sizes of monodisperse fused aluminosilicate particles labeled with 169 Yb. Anatomical lung models were developed for four species (human, Beagle dog, rat and Syrian hamster) that were based on detailed morphometric measurements of replica lung casts. Emphasis was placed on developing a lobar typical-path lung model and on developing a modeling technique which could be applied to various mammalian species. A set of particle deposition equations for deposition caused by inertial impaction, sedimentation, and diffusion were developed. Theoretical models of particle deposition were developed based on these equations and on the anatomical lung models

  9. Differentiation of debris-flow and flash-flood deposits: implications for paleoflood investigations

    Science.gov (United States)

    Waythomas, Christopher F.; Jarrett, Robert D.; ,

    1993-01-01

    Debris flows and flash floods are common geomorphic processes in the Colorado Rocky Mountain Front Range and foothills. Usually, debris flows and flash floods are associated with excess summer rainfall or snowmelt, in areas were unconsolidated surficial deposits are relatively thick and slopes are steep. In the Front Range and foothills, flash flooding is limited to areas below about 2300m whereas, debris flow activity is common throughout the foothill and alpine zones and is not necessarily elevation limited. Because flash floods and debris flows transport large quantities of bouldery sediment, the resulting deposits appear somewhat similar even though such deposits were produced by different processes. Discharge estimates based on debris-flow deposits interpreted as flash-flood deposits have large errors because techniques for discharge retrodiction were developed for water floods with negligible sediment concentrations. Criteria for differentiating between debris-flow and flash-flood deposits are most useful for deposits that are fresh and well-exposed. However, with the passage of time, both debris-flow and flash-flood deposits become modified by the combined effects of weathering, colluviation, changes in surface morphology, and in some instances removal of interstitial sediment. As a result, some of the physical characteristics of the deposits become more alike. Criteria especially applicable to older deposits are needed. We differentiate flash-flood from debris-flow and other deposits using clast fabric measurements and other morphologic and sedimentologic techniques (e.g., deposit morphology, clast lithology, particle size and shape, geomorphic setting).

  10. Alternate slicing and deposition strategies for fused deposition modelling of light curved parts

    OpenAIRE

    B. Huang; S. Singamneni

    2012-01-01

    Fused deposition modeling (FDM), as one of the additive manufacturing (AM) techniques, has been widely used in the manufacturing industry from the 1990s. It is relatively cheaper than other AM methods and there are other advantages such as being able to process a variety of other polymers. Currently, FDM is more likely to be suitable for direct production of the terminal-use parts, in some cases challenging traditional process such as injection molding. Research evidences indicate that change...

  11. High powered pulsed plasma enhanced deposition of thin film semiconductor and optical materials

    International Nuclear Information System (INIS)

    Llewellyn, I.P.; Sheach, K.J.A.; Heinecke, R.A.

    1993-01-01

    A glow discharge deposition technique is described which allows the deposition of a large range of high quality materials without the requirement for substrate heating. The method is differentiated from conventional plasma deposition techniques in that a much higher degree of dissociation is achieved in the gases prior to deposition, such that thermally activated surface reactions are no longer required in order to produce a dense film. The necessary discharge intensity (>300Wcm -3 ) is achieved using a high power radio frequency generator which is pulsed at a low duty cycle (1%) to keep the average energy of the discharge low (100W), in order to avoid the discharge heating the substrate. In addition, by varying the gas composition between discharge pulses, layered structures of materials can be produced, with a disordered interface about 8 A thick. Various uses of the technique in semiconductor and optical filter production are described, and the properties of films deposited using these technique are presented. (orig.)

  12. 76 FR 21265 - Interest on Deposits; Deposit Insurance Coverage

    Science.gov (United States)

    2011-04-15

    ... demand deposits will be repealed pursuant to the Dodd-Frank Wall Street Reform and Consumer Protection... a definition of ``interest'' that may assist the FDIC in interpreting a recent statutory amendment... accounts, the FDIC also proposes to retain and move the definition of ``interest'' into the deposit...

  13. Cellulose synthesis inhibition, cell expansion, and patterns of cell wall deposition in Nitella internodes

    International Nuclear Information System (INIS)

    Richmond, P.A.; Metraux, J.P.

    1984-01-01

    The authors have investigated the pattern of wall deposition and maturation and correlated it with cell expansion and cellulose biosynthesis. The herbicide 2,6-dichlorobenzonitrile (DCB) was found to be a potent inhibitor of cellulose synthesis, but not of cell expansion in Nitella internodal cells. Although cellulose synthesis is inhibited during DCB treatment, matrix substances continue to be synthesized and deposited. The inhibition of cellulose microfibril deposition can be demonstrated by various techniques. These results demonstrate that matrix deposition is by apposition, not by intussusception, and that the previously deposited wall moves progressively outward while stretching and thinning as a result of cell expansion

  14. Remote microwave plasma enhanced chemical vapor deposition (RMPECVD) of silica and alumina films

    Energy Technology Data Exchange (ETDEWEB)

    Desmaison, J.; Hidalgo, H.; Tristant, P.; Naudin, F.; Merle, D. [Limoges Univ. (France). Lab. de Sciences des Procedes Ceramiques et Traitements de Surface

    2002-07-01

    Alumina or silica are attractive as insulation and protective layers for sensitive substrates. Oxides are deposited by remote microwave plasma enhanced chemical vapor deposition (RMPECVD) using an oxygen plasma and a mixture of precursor gas silane or trimethylaluminum (TMA) diluted in argon, respectively for silica and alumina, injected in the afterglow. This technique allows to deposit films of SiO{sub 2} and Al{sub 2}O{sub 3} with satisfactory characteristics (density, etch rate, stoichiometry) and high deposition rate. The comparison of the best deposition conditions reveals that in case of alumina higher temperatures and lower pressures are needed. (orig.)

  15. Progress in thin film techniques

    International Nuclear Information System (INIS)

    Weingarten, W.

    1996-01-01

    Progress since the last Workshop is reported on superconducting accelerating RF cavities coated with thin films. The materials investigated are Nb, Nb 3 Sn, NbN and NbTiN, the techniques applied are diffusion from the vapour phase (Nb 3 Sn, NbN), the bronze process (Nb 3 Sn), and sputter deposition on a copper substrate (Nb, NbTiN). Specially designed cavities for sample evaluation by RF methods have been developed (triaxial cavity). New experimental techniques to assess the RF amplitude dependence of the surface resistance are presented (with emphasis on niobium films sputter deposited on copper). Evidence is increasing that they are caused by magnetic flux penetration into the surface layer. (R.P.)

  16. Uranium deposits in granitic rocks

    International Nuclear Information System (INIS)

    Nishimori, R.K.; Ragland, P.C.; Rogers, J.J.W.; Greenberg, J.K.

    1977-01-01

    This report is a review of published data bearing on the geology and origin of uranium deposits in granitic, pegmatitic and migmatitic rocks with the aim of assisting in the development of predictive criteria for the search for similar deposits in the U.S. Efforts were concentrated on the so-called ''porphyry'' uranium deposits. Two types of uranium deposits are primarily considered: deposits in pegmatites and alaskites in gneiss terrains, and disseminations of uranium in high-level granites. In Chapter 1 of this report, the general data on the distribution of uranium in igneous and metamorphic rocks are reviewed. Chapter 2 contains some comments on the classification of uranium deposits associated with igneous rocks and a summary of the main features of the geology of uranium deposits in granites. General concepts of the behavior of uranium in granites during crustal evolution are reviewed in Chapter 3. Also included is a discussion of the relationship of uranium mineralization in granites to the general evolution of mobile belts, plus the influence of magmatic and post-magmatic processes on the distribution of uranium in igneous rocks and related ore deposits. Chapter 4 relates the results of experimental studies on the crystallization of granites to some of the geologic features of uranium deposits in pegmatites and alaskites in high-grade metamorphic terrains. Potential or favorable areas for igneous uranium deposits in the U.S.A. are delineated in Chapter 5. Data on the geology of specific uranium deposits in granitic rocks are contained in Appendix 1. A compilation of igneous rock formations containing greater than 10 ppM uranium is included in Appendix 2. Appendix 3 is a report on the results of a visit to the Roessing area. Appendix 4 is a report on a field excursion to eastern Canada

  17. Ti-doped hydrogenated diamond like carbon coating deposited by hybrid physical vapor deposition and plasma enhanced chemical vapor deposition

    Science.gov (United States)

    Lee, Na Rae; Sle Jun, Yee; Moon, Kyoung Il; Sunyong Lee, Caroline

    2017-03-01

    Diamond-like carbon films containing titanium and hydrogen (Ti-doped DLC:H) were synthesized using a hybrid technique based on physical vapor deposition (PVD) and plasma enhanced chemical vapor deposition (PECVD). The film was deposited under a mixture of argon (Ar) and acetylene gas (C2H2). The amount of Ti in the Ti-doped DLC:H film was controlled by varying the DC power of the Ti sputtering target ranging from 0 to 240 W. The composition, microstructure, mechanical and chemical properties of Ti-doped DLC:H films with varying Ti concentrations, were investigated using Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), nano indentation, a ball-on-disk tribometer, a four-point probe system and dynamic anodic testing. As a result, the optimum composition of Ti in Ti-doped DLC:H film using our hybrid method was found to be a Ti content of 18 at. %, having superior electrical conductivity and high corrosion resistance, suitable for bipolar plates. Its hardness value was measured to be 25.6 GPa with a low friction factor.

  18. Atomic layer deposition of nanostructured materials

    CERN Document Server

    Pinna, Nicola

    2012-01-01

    Atomic layer deposition, formerly called atomic layer epitaxy, was developed in the 1970s to meet the needs of producing high-quality, large-area fl at displays with perfect structure and process controllability. Nowadays, creating nanomaterials and producing nanostructures with structural perfection is an important goal for many applications in nanotechnology. As ALD is one of the important techniques which offers good control over the surface structures created, it is more and more in the focus of scientists. The book is structured in such a way to fi t both the need of the expert reader (du

  19. COAL-FIRED UTILITY BOILERS: SOLVING ASH DEPOSITION PROBLEMS; TOPICAL

    International Nuclear Information System (INIS)

    Christopher J. Zygarlicke; Donald P. McCollor; Steven A. Benson; Jay R. Gunderson

    2001-01-01

    The accumulation of slagging and fouling ash deposits in utility boilers has been a source of aggravation for coal-fired boiler operators for over a century. Many new developments in analytical, modeling, and combustion testing methods in the past 20 years have made it possible to identify root causes of ash deposition. A concise and comprehensive guidelines document has been assembled for solving ash deposition as related to coal-fired utility boilers. While this report accurately captures the current state of knowledge in ash deposition, note that substantial research and development is under way to more completely understand and mitigate slagging and fouling. Thus, while comprehensive, this document carries the title ''interim,'' with the idea that future work will provide additional insight. Primary target audiences include utility operators and engineers who face plant inefficiencies and significant operational and maintenance costs that are associated with ash deposition problems. Pulverized and cyclone-fired coal boilers are addressed specifically, although many of the diagnostics and solutions apply to other boiler types. Logic diagrams, ash deposit types, and boiler symptoms of ash deposition are used to aid the user in identifying an ash deposition problem, diagnosing and verifying root causes, determining remedial measures to alleviate or eliminate the problem, and then monitoring the situation to verify that the problem has been solved. In addition to a step-by-step method for identifying and remediating ash deposition problems, this guideline document (Appendix A) provides descriptions of analytical techniques for diagnostic testing and gives extensive fundamental and practical literature references and addresses of organizations that can provide help in alleviating ash deposition problems

  20. Comparison of lanthanum substituted bismuth titanate (BLT) thin films deposited by sputtering and pulsed laser deposition

    Energy Technology Data Exchange (ETDEWEB)

    Besland, M.P. [Institut des Materiaux Jean Rouxel, Universite de Nantes, UMR CNRS 6502, 2 rue de la Houssiniere, B.P. 32229, 44322, Nantes cedex 3 (France)]. E-mail: Marie-Paule.Besland@cnrs-imn.fr; Djani-ait Aissa, H. [Division milieux Ionises et lasers, Centre de Developpement des Technologies Avancees CDTA, Baba Hassen Alger, Algerie (Algeria); Barroy, P.R.J. [Institut des Materiaux Jean Rouxel, Universite de Nantes, UMR CNRS 6502, 2 rue de la Houssiniere, B.P. 32229, 44322, Nantes cedex 3 (France); Lafane, S. [Division milieux Ionises et lasers, Centre de Developpement des Technologies Avancees CDTA, Baba Hassen Alger, Algerie (Algeria); Tessier, P.Y. [Institut des Materiaux Jean Rouxel, Universite de Nantes, UMR CNRS 6502, 2 rue de la Houssiniere, B.P. 32229, 44322, Nantes cedex 3 (France); Angleraud, B. [Institut des Materiaux Jean Rouxel, Universite de Nantes, UMR CNRS 6502, 2 rue de la Houssiniere, B.P. 32229, 44322, Nantes cedex 3 (France); Richard-Plouet, M. [Institut des Materiaux Jean Rouxel, Universite de Nantes, UMR CNRS 6502, 2 rue de la Houssiniere, B.P. 32229, 44322, Nantes cedex 3 (France); Brohan, L. [Institut des Materiaux Jean Rouxel, Universite de Nantes, UMR CNRS 6502, 2 rue de la Houssiniere, B.P. 32229, 44322, Nantes cedex 3 (France); Djouadi, M.A. [Institut des Materiaux Jean Rouxel, Universite de Nantes, UMR CNRS 6502, 2 rue de la Houssiniere, B.P. 32229, 44322, Nantes cedex 3 (France)

    2006-01-20

    Bi{sub 4-x}La {sub x}Ti{sub 3}O{sub 12} (BLT {sub x}) (x = 0 to 1) thin films were grown on silicon (100) and platinized substrates Pt/TiO{sub 2}/SiO{sub 2}/Si using RF diode sputtering, magnetron sputtering and pulsed laser deposition (PLD). Stoichiometric home-synthesized targets were used. Reactive sputtering was investigated in argon/oxygen gas mixture, with a pressure ranging from 0.33 to 10 Pa without heating the substrate. PLD was investigated in pure oxygen, at a chamber pressure of 20 Pa for a substrate temperature of 400-440 deg. C. Comparative structural, chemical, optical and morphological characterizations of BLT thin films have been performed by X-ray diffraction (XRD), Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS), X-Ray Photoelectron Spectroscopy (XPS), Spectro-ellipsometric measurements (SE) and Atomic Force Microscopy (AFM). Both sputtering techniques allow to obtain uniform films with thickness ranging from 200 to 1000 nm and chemical composition varying from (Bi,La){sub 2} Ti{sub 3} O{sub 12} to (Bi,La){sub 4.5}Ti{sub 3}O{sub 12}, depending on deposition pressure and RF power. In addition, BLT films deposited by magnetron sputtering, at a pressure deposition ranging from 1.1 to 5 Pa, were well-crystallized after a post-deposition annealing at 650 deg. C in oxygen. They exhibit a refractive index and optical band gap of 2.7 and 3.15 eV, respectively. Regarding PLD, single phase and well-crystallized, 100-200 nm thick BLT films with a stoichiometric (Bi,La){sub 4}Ti{sub 3}O{sub 12} chemical composition were obtained, exhibiting in addition a preferential orientation along (200). It is worth noting that BLT films deposited by magnetron sputtering are as well-crystallized than PLD ones.

  1. Geotechnical Description of Mineral Deposits

    Directory of Open Access Journals (Sweden)

    Sasvári Tibor

    1996-06-01

    Full Text Available Performing various mineral deposits extraction methods requires thorough knowledge of the rock masses` geomechanical parameters. In the geotechnical description of mineral deposits there is proposed a methodical approarch at the collection, registration, and evaluation of rock masses` geological properties for geotechnics being applied within the mining industry.

  2. NURE uranium deposit model studies

    International Nuclear Information System (INIS)

    Crew, M.E.

    1981-01-01

    The National Uranium Resource Evaluation (NURE) Program has sponsored uranium deposit model studies by Bendix Field Engineering Corporation (Bendix), the US Geological Survey (USGS), and numerous subcontractors. This paper deals only with models from the following six reports prepared by Samuel S. Adams and Associates: GJBX-1(81) - Geology and Recognition Criteria for Roll-Type Uranium Deposits in Continental Sandstones; GJBX-2(81) - Geology and Recognition Criteria for Uraniferous Humate Deposits, Grants Uranium Region, New Mexico; GJBX-3(81) - Geology and Recognition Criteria for Uranium Deposits of the Quartz-Pebble Conglomerate Type; GJBX-4(81) - Geology and Recognition Criteria for Sandstone Uranium Deposits in Mixed Fluvial-Shallow Marine Sedimentary Sequences, South Texas; GJBX-5(81) - Geology and Recognition Criteria for Veinlike Uranium Deposits of the Lower to Middle Proterozoic Unconformity and Strata-Related Types; GJBX-6(81) - Geology and Recognition Criteria for Sandstone Uranium Deposits of the Salt Wash Type, Colorado Plateau Province. A unique feature of these models is the development of recognition criteria in a systematic fashion, with a method for quantifying the various items. The recognition-criteria networks are used in this paper to illustrate the various types of deposits

  3. Sandstone-type uranium deposits

    International Nuclear Information System (INIS)

    Finch, W.I.; Davis, J.F.

    1985-01-01

    World-class sandstone-type uranium deposits are defined as epigenetic concentrations of uranium minerals occurring as uneven impregnations and minor massive replacements primarily in fluvial, lacustrine, and deltaic sandstone formations. The main purpose of this introductory paper is to define, classify, and introduce to the general geologic setting for sandstone-type uranium deposits

  4. Deposition and Resuspension of Particles

    DEFF Research Database (Denmark)

    Lengweiler, P.; Nielsen, Peter V.; Moser, A.

    A new experimental set-up to investigate the physical process of dust deposition and resuspension on and from surfaces is introduced. Dust deposition can reduce the airBorne dust concentration considerably. As a basis for developing methods to eliminate dust related problems in rooms, there is a ...

  5. A remote coal deposit revisited

    DEFF Research Database (Denmark)

    Bojesen-Kofoed, Jørgen A.; Kalkreuth, Wolfgang; Petersen, Henrik I.

    2012-01-01

    In 1908, members of the “Danmark Expedition” discovered a coal deposit in a very remote area in western Germania Land, close to the margin of the inland ice in northeast Greenland. The deposit was, however, neither sampled nor described, and was revisited in 2009 for the first time since its...

  6. Reactive sputter deposition

    CERN Document Server

    Mahieu, Stijn

    2008-01-01

    In this valuable work, all aspects of the reactive magnetron sputtering process, from the discharge up to the resulting thin film growth, are described in detail, allowing the reader to understand the complete process. Hence, this book gives necessary information for those who want to start with reactive magnetron sputtering, understand and investigate the technique, control their sputtering process and tune their existing process, obtaining the desired thin films.

  7. Multilayer Optical Coating Fabrication By Ion Beam Sputter Deposition

    Science.gov (United States)

    Becker, Juergen; Scheuer, Volker

    1989-02-01

    Ion Beam Sputter Deposition (IBSD) was proven to be a useful technique for producing high performance optical coatings. However, compared to other deposition techniques, several problems remain to be solved, such as low deposition rates, small areas with homogeneous deposition rate and the problem of contamination. In the work described here, a cubic vacuum chamber has been equipped with a commercially available ion beam source, a triple stage target holder and a rotating substrate holder. The primary interest was to get a reasonable deposition rate over a sufficiently large area. Single layers of SiO2, Ta205 and TiO2 and multilayers of Si02/Ta205 were produced. Contaminants in the films were analyzed by various techniques mainly by Total-Reflection X-ray Fluorescence (TXRF). Optical properties of the coatings were investigated to study the influence of the contaminants on the performance of the optical coatings. The optical properties were characterized by the refractive index, the absorption coefficient and the scattering behaviour. Scattering losses were measured by means of Total Integrated Scattering (TIS) and Angle Resolved Scattering (ARS). The damage threshold against high-power laser pulses of 1.06 pm was determined.

  8. Laser deposition of HTSC films

    International Nuclear Information System (INIS)

    Sobol', Eh.N.; Bagratashvili, V.N.; Zherikhin, A.N.; Sviridov, A.P.

    1990-01-01

    Studies of the high-temperature superconducting (HTSC) films fabrication by the laser deposition are reviewed. Physical and chemical processes taking place during laser deposition are considered, such as the target evaporation, the material transport from the target to the substrate, the film growth on the substrate, thermochemical reactions and mass transfer within the HTSC films and their stability. The experimental results on the laser deposition of different HTSC ceramics and their properties investigations are given. The major technological issues are discussed including the deposition schemes, the oxygen supply, the target compositions and structure, the substrates and interface layers selection, the deposition regimes and their impact on the HTSC films properties. 169 refs.; 6 figs.; 2 tabs

  9. Surficial uranium deposits in Botswana

    International Nuclear Information System (INIS)

    Mortimer, C.

    1984-01-01

    The known surficial uranium deposits in Botswana are supergene concentrations either in soils above lower Karoo sediments, or in peat and calcified alluvium of dry stream courses in the Kalahari Desert. A number of uranium occurrences lie above Karoo sedimentary rocks and of these Mokobaesi No. 1 is the best explored. It is a tabular body of disseminated uranium ochre occurring immediately below surface in calcrete and calcified mudstone. The uranium is believed to have migrated upwards from the Karoo rocks. Reconnaissance investigations show that moderately anomalous uranium occurs at a number of localities in peat and calcified sediments that have been deposited in ephemeral water courses. None of these deposits are economic, but the known occurrences are encouraging indications that such deposits may exist in the thick Tertiary to Recent ''Kalahari beds'', that were deposited in diverse palaeoenvironments. (author)

  10. The simple approach to deposition

    International Nuclear Information System (INIS)

    Jensen, N.O.

    1980-01-01

    The use of a simple top hat plume model in conjunction with the principle of source depletion facilitates an analytical treatment of the deposition problem. With such a model, explicit formulae for downwind deposition amounts and ground level atmospheric concentrations are given. The method has the advantage of allowing estimates of the most unfavorable parameter combinations for, say, the maximum deposition that can occur at a given distance from the source. With regard to the land contamination problem, where an area is defined as 'contaminated' when the amount of deposited material is greater than some minimum value, estimates of, for example, the maximum area contaminated and the maximum amount of contamination deposited will also be given

  11. Deposit Structure for Particle-laden Droplets Targeted by Electrospray

    Science.gov (United States)

    Ghafouri, Aref; Singler, Timothy; Yong, Xin; Chiarot, Paul

    2017-11-01

    A hybrid printing technique that combines electrospray atomization with inkjet printing provides unique capabilities for exploring transport creating nanoparticle deposits with controlled structures. In this research, we use electrospray to deliver dry nanoparticles to the interface of particle-laden sessile droplets. Upon evaporation of the target sessile droplet, the particles at the interface are mapped to the underlying substrate. Particle locations in the final deposit were observed separately by tagging the particles dispersed inside the droplet and at its interface with different fluorophores. As expected, surfactant-free particles inside the target droplet were transported to its (pinned) contact line, creating a ``coffee ring'' morphology in the final deposit. The transport and final location of the interfacial particles was highly dependent on the presence of surfactant in the electrosprayed solution. If surfactant was present, the interfacial particles were transported to the apex of the target droplet, forming a dense region at the center of the final deposit. If the electrosprayed solution was surfactant-free, the transport of the interfacial particles was arrested and they were distributed uniformly across the final deposit. Similar deposit morphologies were found when experimenting with various surfactants, including Tween and sodium dodecyl sulfate. These results highlight the important of Marangoni flow in governing the final deposit structure for hybrid printing. This research supported by the National Science Foundation (Award 1538090).

  12. Polymer deposition morphology by electrospray deposition - Modifications through distance variation

    International Nuclear Information System (INIS)

    Altmann, K.; Schulze, R.-D.; Friedrich, J.

    2014-01-01

    Electrospray deposition (ESD) of highly diluted polymers was examined with regard to the deposited surface structure. Only the flight distance (flight time) onto the resulting deposited surface was varied from 20 to 200 mm. An apparatus without any additional heating or gas flows was used. Polyacrylic acid (PAA) and polyallylamine (PAAm) in methanol were deposited on Si wafers. The polymer layers were characterized by scanning electron microscopy, X-ray photoelectron spectroscopy, derivatization reactions and Fourier transform infrared spectroscopy using a grazing incidence unit. SEM images illustrated the changing structures of PAA and PAAm. For PAA the deposited structure changed from a smooth film (20 mm) to a film with individual droplets on the coated surface (100 mm and 200 mm), while for PAAm individual droplets can be seen at all distances. The ESD process with cascades of splitting droplets slows down for PAA after distances greater than 40 mm. In contrast, the ESD process for PAAm is nearly stopped within the first flight distance of 20 mm. Residual solvent analysis showed that most of the solvent evaporated within the first 20 mm capillary-sample distance. - Highlights: • We deposited polyacrylic acid and polyallylamine by electrospray ionization (ESI). • The morphology in dependence of flight distance (20 mm to 200 mm) was analyzed. • The amount of residual solvent after deposition was determined. • ESI-process slows down for polyacrylic acid after 40 mm flight distance. • ESI-Process is complete for polyallylamine within the first 20 mm

  13. ZnSe thin films by chemical bath deposition method

    Energy Technology Data Exchange (ETDEWEB)

    Lokhande, C.D.; Patil, P.S.; Tributsch, H. [Hahn-Meitner-Institute, Bereich Physikalische Chemie, Abt. CS, Glienicker Strasse-100, D-14109 Berlin (Germany); Ennaoui, A. [Hahn-Meitner-Institute, Bereich Physikalische Chemie, Abt. CG, Glienicker Strasse-100, D-14109 Berlin (Germany)

    1998-09-04

    The ZnSe thin films have been deposited onto glass substrates by the simple chemical bath deposition method using selenourea as a selenide ion source from an aqueous alkaline medium. The effect of Zn ion concentration, bath temperature and deposition time period on the quality and thickness of ZnSe films has been studied. The ZnSe films have been characterized by XRD, TEM, EDAX, TRMC (time-resolved microwave conductivity), optical absorbance and RBS techniques for their structural, compositional, electronic and optical properties. The as-deposited ZnSe films are found to be amorphous, Zn rich with optical band gap, Eg, equal to 2.9 eV

  14. Electrical Interconnection Of Superconducting Strands By Electrolytic CU Deposition.

    CERN Document Server

    Scheuerlein, C; Heck, S; Ams, A

    2011-01-01

    The electrical interconnection of Nb3Sn/Cu strands is a key issue for the construction of superconducting devices such as Nb3Sn based insertion devices for third generation light sources. As an alternative connection method for brittle superconducting strands like Nb3Sn/Cu, test joints have been produced by electrolytic deposition of Cu. The resistance of first test joints produced by electrolytic Cu deposition with a strand overlap length of 3 cm at 4.2 K is about 10 n$\\omega$, similar to the resistance measured for joints produced by soft soldering with the same strand overlap length. Interconnection by electrolytic Cu deposition can be done before or after the reaction heat treatment, and it produces a mechanically strong connection. Simulations have been performed with Comsol multiphysics in order to estimate the influence of deposit imperfections on the joint resistance, and to compare the resistance of joints made with different techniques

  15. Deposition and characterization of ZnSe nanocrystalline thin films

    Science.gov (United States)

    Temel, Sinan; Gökmen, F. Özge; Yaman, Elif; Nebi, Murat

    2018-02-01

    ZnSe nanocrystalline thin films were deposited at different deposition times by using the Chemical Bath Deposition (CBD) technique. Effects of deposition time on structural, morphological and optical properties of the obtained thin films were characterized. X-ray diffraction (XRD) analysis was used to study the structural properties of ZnSe nanocrystalline thin films. It was found that ZnSe thin films have a cubic structure with a preferentially orientation of (111). The calculated average grain size value was about 28-30 nm. The surface morphology of these films was studied by the Field Emission Scanning Electron Microscope (FESEM). The surfaces of the thin films were occurred from small stacks and nano-sized particles. The band gap values of the ZnSe nanocrystalline thin films were determined by UV-Visible absorption spectrum and the band gap values were found to be between 2.65-2.86 eV.

  16. Radionuclide techniques

    International Nuclear Information System (INIS)

    Alazraki, N.

    1988-01-01

    During approximately 25 years of experience with bone scanning, broad expansions in the clinical impact of radionuclide imaging on disorders of bones, joints, and soft tissues have occurred. This increased impact had its groundwork laid by advances in radiopharmaceuticals and instruments that are used for bone imaging. The progression from /sup 85/Sr- to /sup 99m/Tc-labeled phosphate and phosphonate compounds, coupled with the advance from crude rectilinear scanning techniques to whole body scintillation imaging with large crystal cameras and sophisticated electronics, has encourage use of radionuclide techniques in the evaluation of muscoloskeletal diseases. Many clinical studies have documented the high degree of sensitivity of the bone scan compared with that of the radiograph in detecting osseous and articular abnormalities

  17. Astrophysical techniques

    CERN Document Server

    Kitchin, CR

    2013-01-01

    DetectorsOptical DetectionRadio and Microwave DetectionX-Ray and Gamma-Ray DetectionCosmic Ray DetectorsNeutrino DetectorsGravitational Radiation Dark Matter and Dark Energy Detection ImagingThe Inverse ProblemPhotographyElectronic ImagingScanningInterferometrySpeckle InterferometryOccultationsRadarElectronic ImagesPhotometryPhotometryPhotometersSpectroscopySpectroscopy SpectroscopesOther TechniquesAstrometryPolarimetrySolar StudiesMagnetometryComputers and The Internet.

  18. Aseptic technique.

    Science.gov (United States)

    Bykowski, Tomasz; Stevenson, Brian

    2008-11-01

    This chapter describes common laboratory procedures that can reduce the risk of culture contaminations (sepsis), collectively referred as "aseptic technique." Two major strategies of aseptic work are described: using a Bunsen burner and a laminar flow hood. Both methods are presented in the form of general protocols applicable to a variety of laboratory tasks such as pipetting and dispensing aliquots, preparing growth media, and inoculating, passaging, and spreading microorganisms on petri dishes. Copyright 2008 by John Wiley & Sons, Inc.

  19. TULSA UNIVERSITY PARAFFIN DEPOSITION PROJECTS

    Energy Technology Data Exchange (ETDEWEB)

    Michael Volk; Cem Sarica

    2003-10-01

    As oil and gas production moves to deeper and colder water, subsea multiphase production systems become critical for economic feasibility. It will also become increasingly imperative to adequately identify the conditions for paraffin precipitation and predict paraffin deposition rates to optimize the design and operation of these multiphase production systems. Although several oil companies have paraffin deposition predictive capabilities for single-phase oil flow, these predictive capabilities are not suitable for the multiphase flow conditions encountered in most flowlines and wellbores. For deepwater applications in the Gulf of Mexico, it is likely that multiphase production streams consisting of crude oil, produced water and gas will be transported in a single multiphase pipeline to minimize capital cost and complexity at the mudline. Existing single-phase (crude oil) paraffin deposition predictive tools are clearly inadequate to accurately design these pipelines because they do not account for the second and third phases, namely, produced water and gas. The objective of this program is to utilize the current test facilities at The University of Tulsa, as well as member company expertise, to accomplish the following: enhance our understanding of paraffin deposition in single and two-phase (gas-oil) flows; conduct focused experiments to better understand various aspects of deposition physics; and, utilize knowledge gained from experimental modeling studies to enhance the computer programs developed in the previous JIP for predicting paraffin deposition in single and two-phase flow environments. These refined computer models will then be tested against field data from member company pipelines. The following deliverables are scheduled during the first three projects of the program: (1) Single-Phase Studies, with three different black oils, which will yield an enhanced computer code for predicting paraffin deposition in deepwater and surface pipelines. (2) Two

  20. Presentation Technique

    International Nuclear Information System (INIS)

    Froejmark, M.

    1992-10-01

    The report presents a wide, easily understandable description of presentation technique and man-machine communication. General fundamentals for the man-machine interface are illustrated, and the factors that affect the interface are described. A model is presented for describing the operators work situation, based on three different levels in the operators behaviour. The operator reacts routinely in the face of simple, known problems, and reacts in accordance with predetermined plans in the face of more complex, recognizable problems. Deep fundamental knowledge is necessary for truly complex questions. Today's technical status and future development have been studied. In the future, the operator interface will be based on standard software. Functions such as zooming, integration of video pictures, and sound reproduction will become common. Video walls may be expected to come into use in situations in which several persons simultaneously need access to the same information. A summary of the fundamental rules for the design of good picture ergonomics and design requirements for control rooms are included in the report. In conclusion, the report describes a presentation technique within the Distribution Automation and Demand Side Management area and analyses the know-how requirements within Vattenfall. If different systems are integrated, such as geographical information systems and operation monitoring systems, strict demands are made on the expertise of the users for achieving a user-friendly technique which is matched to the needs of the human being. (3 figs.)

  1. Chemical solution deposition: a path towards low cost coated conductors

    International Nuclear Information System (INIS)

    Obradors, X; Puig, T; Pomar, A; Sandiumenge, F; Pinol, S; Mestres, N; Castano, O; Coll, M; Cavallaro, A; Palau, A; Gazquez, J; Gonzalez, J C; Gutierrez, J; Roma, N; Ricart, S; Moreto, J M; Rossell, M D; Tendeloo, G van

    2004-01-01

    The achievement of low cost deposition techniques for high critical current YBa 2 Cu 3 O 7 coated conductors is one of the major objectives to achieve a widespread use of superconductivity in power applications. Chemical solution deposition techniques are appearing as a very promising methodology to achieve epitaxial oxide thin films at a low cost, so an intense effort is being carried out to develop routes for all chemical coated conductor tapes. In this work recent achievements will be presented towards the goal of combining the deposition of different type of buffer layers on metallic substrates based on metal-organic decomposition with the growth of YBa 2 Cu 3 O 7 layers using the trifluoroacetate route. The influence of processing parameters on the microstructure and superconducting properties will be stressed. High critical currents are demonstrated in 'all chemical' multilayers

  2. RETADD: a Regional Trajectory And Diffusion-Deposition model

    Energy Technology Data Exchange (ETDEWEB)

    Begovich, C. L.; Murphy, B. D.; Nappo, Jr., C. J.

    1978-06-01

    The Regional Trajectory and Diffusion-Deposition Model (RETADD) is based upon a version of the National Oceanic and Atmospheric Administration Air Resources Laboratory's Regional-Continental Scale Transport, Diffusion, and Deposition Model. The FORTRAN IV computer model uses a trajectory analysis technique for estimating the transport and long-range diffusion of material emitted from a point source. The wind trajectory portion of the code uses observed upper air winds to compute the transport of the material. Ground level concentrations and depositions are computed by using the Gaussian plume equation for wind trajectories projected forward in time. Options are included to specify an upper bound for the mixed layer and a chemical decomposition rate for the effluent. The limitations to the technique are discussed, the equations and model are described, and listings of the program, input, and output are included.

  3. Large area periodic ferromagnetic nanowires deposited onto a polymer substrate

    Science.gov (United States)

    Zighem, F.; Faurie, D.; Belmeguenai, M.; Garcia-Sanchez, A.; Lupo, P.; Adeyeye, A. O.

    2017-07-01

    There are various challenges associated with the fabrication of highly ordered magnetic nanostructures on flexible substrates due to the compatibility with lithography and deposition techniques. In this article, we present a nanofabrication technique to synthesize a large area (5 × 5 mm2) of ferromagnetic nanowires on top of a polymer substrate (Kapton®) using interference lithography and sputtering processes. We have systematically characterized their static and dynamic magnetic behaviors using magneto-optical Kerr magnetometry and broadband ferromagnetic resonance spectroscopy. To evaluate the quality of our approach, we also deposited an identical array of nanowires on Silicon substrates for comparison. The nanowires deposited on the two substrates display similar static and dynamic properties, including the identical magnetization reversal process, number of resonance modes, and comparable damping parameters. The results suggest the good quality of our nanowires and their suitability in future flexible spintronic devices.

  4. Carbonate rock depositional models: A microfacies approach

    Energy Technology Data Exchange (ETDEWEB)

    Carozzi, A.V.

    1988-01-01

    Carbonate rocks contain more than 50% by weight carbonate minerals such as calcite, dolomite, and siderite. Understanding how these rocks form can lead to more efficient methods of petroleum exploration. Micofacies analysis techniques can be used as a method of predicting models of sedimentation for carbonate rocks. Micofacies in carbonate rocks can be seen clearly only in thin sections under a microscope. This section analysis of carbonate rocks is a tool that can be used to understand depositional environments, diagenetic evolution of carbonate rocks, and the formation of porosity and permeability in carbonate rocks. The use of micofacies analysis techniques is applied to understanding the origin and formation of carbonate ramps, carbonate platforms, and carbonate slopes and basins. This book will be of interest to students and professionals concerned with the disciplines of sedimentary petrology, sedimentology, petroleum geology, and palentology.

  5. Flowslide Early Warning System in pyroclastic deposits

    Science.gov (United States)

    Olivares, Lucio; Damiano, Emila; De Cristofaro, Martina; Roberto, Greco; Mollo, Luigi; Netti, Nadia; Capparelli, Giovanna

    2015-04-01

    Most of the mountains of Campania are covered by airfall pyroclastic deposits in primary deposition generally in unsaturated conditions. These deposits are periodically subjected to rainfall induced landslides that may evolve into catastrophic flowslides. To protect towns EWS can be implemented in order to correctly and promptly predict the trigger. In the paper we detect some 'essential ingredients' for effective EWSs which are new with respect to those already employed and essentially based on pluviometric thresholds (Greco et. Al., 2013) and extremely simplified models not able to correctly follow the physical phenomena which are responsible of flowslides generation (Olivares et Al. 2009). Complex models, able to correctly simulate those physical phenomena such as infiltration processes and the effects of partial saturated conditions on shear strength contain the 'essential ingredients' that we discuss in the paper. A particular attention is devoted to define the relation between suction and shear strength and the water retention curve obtained from different techniques to assess a reliable hydro-geotechnical model to analyze the slope response of loose unsaturated pyroclastic deposits. An EWS that contains these elements can provide many advantages. In fact, catastrophic flowslides but even false alarms about such events, produce negative technological and productive shocks that strongly reduce the actual and prospective value added of investment in the areas at risk suggesting the opportunity of their shrinking and postponement. Of course this severely compromises the economic development of those areas. In the paper we propose to examine this subject in the Dixit e Pindyck framework of the Real Option Valuation Approach in order to explain the socio-economic value of effective EWS. In fact, such EWSs will embed valuable new real options in the investment opportunities in the areas at risk increasing their actual and prospective values. Keywords: slope

  6. The deposition of magnesium fluoride (MGF 2 ) thin films by ...

    African Journals Online (AJOL)

    The Chemical Bath Deposition (CBD) technique was successfully employed in the growth of magnesium fluoride (MgF2) thin films. The films were characterized and optimized. The characterization included: the optical and solid state properties such as the transmittance (T)/reflectance (R) absorbance (A) spectra which ...

  7. Mapping hydrothermal altered mineral deposits using Landsat 7 ...

    Indian Academy of Sciences (India)

    The colour composite and band ratio methods showed very clearly the hydrothermal altered deposits of clay minerals, iron oxides and ferric oxides around the fumaroles. The principal component analysis using the Crosta technique also enabled us to represent undoubtedly the altered hydroxyl and iron-oxide mineral ...

  8. Effects of Deposition Potentialon the Optical Properties of Zinc ...

    African Journals Online (AJOL)

    Thin films of Zinc Sulphide (ZnS) were grown on glass substrate by electrodeposition technique. The optical characterization of the grown films (ZnS) was done by using a Janway 6405 UV-VIS spectrophotometer in the range of 300-900nm using a step size of 20. The effect of deposition potential variationon the films optical ...

  9. Influence of anatomy and head position on intranasal drug deposition

    NARCIS (Netherlands)

    Merkus, Paul; Ebbens, Fenna A.; Muller, Barbara; Fokkens, Wytske J.

    2006-01-01

    The objective of this study was to determine the influence of individual anatomical differences on intranasal drug deposition. The data of a comparison of seven different administration techniques in ten healthy volunteers was used in this single-blind crossover pilot study. After intranasal

  10. Structural, optical and electrical properties of chemically deposited ...

    Indian Academy of Sciences (India)

    Administrator

    Stoichiometric and nonstoichiometric thin films of copper selenide have been prepared by chemical bath deposition technique at temperature below 60°C on glass substrate. The effect of nonstoichiometry on the optical, electrical and structural properties of the film was studied. The bandgap energy was observed to in-.

  11. Application of laser assisted cold spraying process for metal deposition

    CSIR Research Space (South Africa)

    Tlotleng, Monnamme

    2014-02-01

    Full Text Available Laser assisted cold spraying (LACS) process is a hybrid technique that uses laser and cold spray to deposit solid powders on metal substrates. For bonding to occur, the particle velocities must be supersonic which are achieved by entraining...

  12. Thickness effect on properties of titanium film deposited by dc ...

    Indian Academy of Sciences (India)

    This paper reports effect of thickness on the properties of titanium (Ti) film deposited on Si/SiO2 (100) substrate using two different methods: d.c. magnetron sputtering and electron beam (e-beam) evaporation technique. The structural and morphological characterization of Ti film were performed using X-ray diffraction (XRD) ...

  13. Microstrain Determination in Individual Grains of Laser Deposited Cladding Layers

    NARCIS (Netherlands)

    de Oliveira, Uazir O. B.; Ocelik, Vaclav; De Hosson, Jeff T. M.; Chandra, T; Tsuzaki, K; Militzer, M; Ravindran, C

    2007-01-01

    The laser cladding technique makes the deposition of thick metallic, wear and corrosion resistant coatings feasible on weaker substrates. During the process, localized high thermal gradients generate internal stresses that may cause cracking when these overcome the fracture stress. To explain the

  14. Microscopic characterisation of suspended graphene grown by chemical vapour deposition

    NARCIS (Netherlands)

    Bignardi, L.; Dorp, W.F. van; Gottardi, S.; Ivashenko, O.; Dudin, P.; Barinov, A.; de Hosson, J.T.M.; Stöhr, M.; Rudolf, P.

    2013-01-01

    We present a multi-technique characterisation of graphene grown by chemical vapour deposition (CVD) and thereafter transferred to and suspended on a grid for transmission electron microscopy (TEM). The properties of the electronic band structure are investigated by angle-resolved photoelectron

  15. Broadband infrared absorption enhancement by electroless-deposited silver nanoparticles

    DEFF Research Database (Denmark)

    Gritti, Claudia; Raza, Søren; Kadkhodazadeh, Shima

    2017-01-01

    Decorating semiconductor surfaces with plasmonic nanoparticles (NPs) is considered a viable solution for enhancing the absorptive properties of photovoltaic and photodetecting devices. We propose to deposit silver NPs on top of a semiconductor wafer by a cheap and fast electroless plating technique...

  16. Mapping hydrothermal altered mineral deposits using Landsat 7 ...

    Indian Academy of Sciences (India)

    To evaluate the conventional methods for mapping hydrothermal altered deposits by using Landsat 7. ETM+ image in and around ... component analysis using the Crosta technique also enabled us to represent undoubtedly the altered hydroxyl and ..... target detection algorithms for hyperspectral imagery; In: Algorithms and ...

  17. Characterization of laser metal deposited 316L stainless steel

    CSIR Research Space (South Africa)

    Bayode, A

    2016-06-01

    Full Text Available Laser metal deposition (LMD) is an innovative manufacturing technique that uses laser to melt powders to fabricate fully dense components layer by layer. It is capable of processing different metallic powders and can also be used for consolidating...

  18. Hot-wire assisted atomic layer deposition of Tungsten films

    NARCIS (Netherlands)

    Yang, Mengdi

    2018-01-01

    This thesis aims to establish a novel technique of atomic layer deposition (ALD) for the future ultra-large-scale integration (ULSI) of microelectronics. We developed a hot-wire assisted ALD (HWALD), where a heated tungsten (W) filament is utilized instead of a plasma to generate radicals. HWALD is

  19. Ash Deposition Trials at Three Power Stations in Denmark

    DEFF Research Database (Denmark)

    Laursen, Karin; Frandsen, Flemming; Larsen, Ole Hede

    1998-01-01

    Six full-scale trials were conducted at three power stations in Denmark: Ensted, Funen, and Vendsyssel power stations. During these trials, pulverized coal, bottom ash, fly ash, and deposits from cooled probes were sampled and analyzed with various techniques. On the basis of SEM analyses...

  20. Synthesis of size-controlled Bi particles by electrochemical deposition

    Indian Academy of Sciences (India)

    The particles have been characterized by scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray analysis, X-ray photoelectron spectroscopy, UV-visible spectroscopy and X-ray diffraction technique. The particles, as deposited, are highly crystalline in nature and the particle size and shape ...

  1. Atmospheric deposition 2000. NOVA 2003; Atmosfaerisk deposition 2000. NOVA 2003

    Energy Technology Data Exchange (ETDEWEB)

    Ellermann, T.; Hertel, O.; Hovmand, M.F.; Kemp, K.; Skjoeth, C.A.

    2001-11-01

    This report presents measurements and calculations from the atmospheric part of NOVA 2003 and covers results for 2000. It summarises the main results concerning concentrations and depositions of nitrogen, phosphorus and sulphur compounds related to eutrophication and acidification. Depositions of atmospheric compounds to Danish marine waters as well as land surface are presented. Measurements: In 2000 the monitoring program consisted of eight stations where wet deposition of ammonium, nitrate, phosphate (semi quantitatively) and sulphate were measured using bulk precipitation samplers. Six of the stations had in addition measurements of atmospheric content of A, nitrogen, phosphorus, and sulphur compounds in gas and particulate phase carried out by use of filter pack samplers. Filters were analysed at the National Environmental Research Institute. Furthermore nitrogen dioxide were measured using nitrogen dioxide filter samplers and monitors. Model calculations: The measurements in the monitoring program were supplemented with model calculations of concentrations and depositions of nitrogen and sulphur compounds to Danish land surface, marine waters, fjords and bays using the ACDEP model (Atmospheric Chemistry and Deposition). The model is a so-called trajectory model and simulates the physical and chemical processes in the atmosphere using meteorological and emission data as input. The advantage of combining measurements with model calculations is that the strengths of both methods is obtained. Conclusions concerning: 1) actual concentration levels at the monitoring stations, 2) deposition at the monitoring stations, 3) seasonal variations and 4) long term trends in concentrations and depositions are mainly based on the direct measurements. These are furthermore used to validate the results of the model calculations. Calculations and conclusions concerning: 1) depositions to land surface and to the individual marine water, 2) contributions from different emission

  2. Acid Deposition Maps in Spain

    International Nuclear Information System (INIS)

    Artinano, B.; Cabal, H.; Garcia, C.

    1998-01-01

    Animal and monthly deposition velocity and total sulfur deposition maps have been performed for the peninsular Spain for 1992 by using the inferential method. To do this, updated databases with high space and time resolution, for land uses (CORINE) and meteorological information from analysis modelling for the same year, have been utilized. The final result are deposition maps in a 5x5 Km 2 grid which allow to assess the methodology used in Europe to obtain the maps of excedances over the critical loads of pollutants. (Author) 32 refs

  3. Particle deposition in ventilation ducts

    Energy Technology Data Exchange (ETDEWEB)

    Sippola, Mark Raymond [Univ. of California, Berkeley, CA (United States)

    2002-09-01

    Exposure to airborne particles is detrimental to human health and indoor exposures dominate total exposures for most people. The accidental or intentional release of aerosolized chemical and biological agents within or near a building can lead to exposures of building occupants to hazardous agents and costly building remediation. Particle deposition in heating, ventilation and air-conditioning (HVAC) systems may significantly influence exposures to particles indoors, diminish HVAC performance and lead to secondary pollutant release within buildings. This dissertation advances the understanding of particle behavior in HVAC systems and the fates of indoor particles by means of experiments and modeling. Laboratory experiments were conducted to quantify particle deposition rates in horizontal ventilation ducts using real HVAC materials. Particle deposition experiments were conducted in steel and internally insulated ducts at air speeds typically found in ventilation ducts, 2-9 m/s. Behaviors of monodisperse particles with diameters in the size range 1-16 μm were investigated. Deposition rates were measured in straight ducts with a fully developed turbulent flow profile, straight ducts with a developing turbulent flow profile, in duct bends and at S-connector pieces located at duct junctions. In straight ducts with fully developed turbulence, experiments showed deposition rates to be highest at duct floors, intermediate at duct walls, and lowest at duct ceilings. Deposition rates to a given surface increased with an increase in particle size or air speed. Deposition was much higher in internally insulated ducts than in uninsulated steel ducts. In most cases, deposition in straight ducts with developing turbulence, in duct bends and at S-connectors at duct junctions was higher than in straight ducts with fully developed turbulence. Measured deposition rates were generally higher than predicted by published models. A model incorporating empirical equations based on the

  4. Atomic and molecular layer deposition for surface modification

    International Nuclear Information System (INIS)

    Vähä-Nissi, Mika; Sievänen, Jenni; Salo, Erkki; Heikkilä, Pirjo; Kenttä, Eija; Johansson, Leena-Sisko; Koskinen, Jorma T.; Harlin, Ali

    2014-01-01

    Atomic and molecular layer deposition (ALD and MLD, respectively) techniques are based on repeated cycles of gas–solid surface reactions. A partial monolayer of atoms or molecules is deposited to the surface during a single deposition cycle, enabling tailored film composition in principle down to molecular resolution on ideal surfaces. Typically ALD/MLD has been used for applications where uniform and pinhole free thin film is a necessity even on 3D surfaces. However, thin – even non-uniform – atomic and molecular deposited layers can also be used to tailor the surface characteristics of different non-ideal substrates. For example, print quality of inkjet printing on polymer films and penetration of water into porous nonwovens can be adjusted with low-temperature deposited metal oxide. In addition, adhesion of extrusion coated biopolymer to inorganic oxides can be improved with a hybrid layer based on lactic acid. - Graphical abstract: Print quality of a polylactide film surface modified with atomic layer deposition prior to inkjet printing (360 dpi) with an aqueous ink. Number of printed dots illustrated as a function of 0, 5, 15 and 25 deposition cycles of trimethylaluminum and water. - Highlights: • ALD/MLD can be used to adjust surface characteristics of films and fiber materials. • Hydrophobicity after few deposition cycles of Al 2 O 3 due to e.g. complex formation. • Same effect on cellulosic fabrics observed with low temperature deposited TiO 2 . • Different film growth and oxidation potential with different precursors. • Hybrid layer on inorganic layer can be used to improve adhesion of polymer melt

  5. Atomic and molecular layer deposition for surface modification

    Energy Technology Data Exchange (ETDEWEB)

    Vähä-Nissi, Mika, E-mail: mika.vaha-nissi@vtt.fi [VTT Technical Research Centre of Finland, PO Box 1000, FI‐02044 VTT (Finland); Sievänen, Jenni; Salo, Erkki; Heikkilä, Pirjo; Kenttä, Eija [VTT Technical Research Centre of Finland, PO Box 1000, FI‐02044 VTT (Finland); Johansson, Leena-Sisko, E-mail: leena-sisko.johansson@aalto.fi [Aalto University, School of Chemical Technology, Department of Forest Products Technology, PO Box 16100, FI‐00076 AALTO (Finland); Koskinen, Jorma T.; Harlin, Ali [VTT Technical Research Centre of Finland, PO Box 1000, FI‐02044 VTT (Finland)

    2014-06-01

    Atomic and molecular layer deposition (ALD and MLD, respectively) techniques are based on repeated cycles of gas–solid surface reactions. A partial monolayer of atoms or molecules is deposited to the surface during a single deposition cycle, enabling tailored film composition in principle down to molecular resolution on ideal surfaces. Typically ALD/MLD has been used for applications where uniform and pinhole free thin film is a necessity even on 3D surfaces. However, thin – even non-uniform – atomic and molecular deposited layers can also be used to tailor the surface characteristics of different non-ideal substrates. For example, print quality of inkjet printing on polymer films and penetration of water into porous nonwovens can be adjusted with low-temperature deposited metal oxide. In addition, adhesion of extrusion coated biopolymer to inorganic oxides can be improved with a hybrid layer based on lactic acid. - Graphical abstract: Print quality of a polylactide film surface modified with atomic layer deposition prior to inkjet printing (360 dpi) with an aqueous ink. Number of printed dots illustrated as a function of 0, 5, 15 and 25 deposition cycles of trimethylaluminum and water. - Highlights: • ALD/MLD can be used to adjust surface characteristics of films and fiber materials. • Hydrophobicity after few deposition cycles of Al{sub 2}O{sub 3} due to e.g. complex formation. • Same effect on cellulosic fabrics observed with low temperature deposited TiO{sub 2}. • Different film growth and oxidation potential with different precursors. • Hybrid layer on inorganic layer can be used to improve adhesion of polymer melt.

  6. Investigation of vanadium and nitride alloys thin layers deposited by PVD

    Directory of Open Access Journals (Sweden)

    Nouveau C.

    2012-06-01

    Full Text Available In this work we present the technique of magnetron vapor deposition and the effect of several deposition parameters on the structural and morphological properties of prepared thin films. It was noted that the deposition time has an effect on the crystallinity, mechanical properties such as residual stress, roughness surface and the layer composition from target products. Studies were carried out on layers of vanadium (V and the nitride vanadium (VN.

  7. Fabrication of 100 A class, 1 m long coated conductor tapes by metal organic chemical vapor deposition and pulsed laser deposition

    Energy Technology Data Exchange (ETDEWEB)

    Selvamanickam, V.; Lee, H.G.; Li, Y.; Xiong, X.; Qiao, Y.; Reeves, J.; Xie, Y.; Knoll, A.; Lenseth, K

    2003-10-15

    SuperPower has been scaling up YBa{sub 2}Cu{sub 3}O{sub x}-based second-generation superconducting tapes by techniques such as pulsed laser deposition (PLD) using industrial laser and metal organic chemical vapor deposition (MOCVD). Both techniques offer advantage of high deposition rates, which is important for high throughput. Using highly-polished substrates produced in a reel-to-reel polishing facility and buffer layers deposited in a pilot ion beam assisted deposition facility, meter-long second-generation high temperature superconductor tapes have been produced. 100 A class, meter-long coated conductor tapes have been reproducibly demonstrated in this work by both MOCVD and PLD. The best results to date are 148 A over 1.06 m by MOCVD and 135 A over 1.1 m by PLD using industrial laser.

  8. Terahertz Techniques

    CERN Document Server

    Bründermann, Erik; Kimmitt, Maurice FitzGerald

    2012-01-01

    Research and development in the terahertz portion of the electromagnetic spectrum has expanded very rapidly during the past fifteen years due to major advances in sources, detectors and instrumentation. Many scientists and engineers are entering the field and this volume offers a comprehensive and integrated treatment of all aspects of terahertz technology. The three authors, who have been active researchers in this region over a number of years, have designed Terahertz Techniques to be both a general introduction to the subject and a definitive reference resource for all those involved in this exciting research area.

  9. Phosphorus doping and deposition pressure effects on optical and electrical properties of polysilicon

    International Nuclear Information System (INIS)

    Zaghdoudi, M.; Abdelkrim, M.M.; Fathallah, M.; Mohammed-Brahim, T.; Rogel, R.

    2006-01-01

    The optical and electrical properties of amorphously deposited and then post-crystallized silicon films are studied as a function of the deposition pressure and the phosphorus doping. Amorphous silicon films are deposited in a high pressure regime by SAPCVD (Sub-Atmospheric Pressure Chemical Vapour Deposition) to study the effect of the deposition pressure. They are also deposited in a low pressure regime by LPCVD (Low Pressure Chemical Vapour Deposition) to study the effect of a low phosphorus doping. Both types of amorphous films are then crystallized in the solid phase at 600 deg. C. Using different optical and electrical characterization techniques, the beneficial effect of a high pressure as well as of a weak phosphorus doping on the decrease of the defect density is highlighted. These results give some ways to improve the quality of polysilicon enough to be used in photovoltaic or in thin film electronic devices

  10. Characterization of CdTe Films Deposited at Various Bath Temperatures and Concentrations Using Electrophoretic Deposition

    Directory of Open Access Journals (Sweden)

    Zulkarnain Zainal

    2012-05-01

    Full Text Available CdTe film was deposited using the electrophoretic deposition technique onto an ITO glass at various bath temperatures. Four batch film compositions were used by mixing 1 to 4 wt% concentration of CdTe powder with 10 mL of a solution of methanol and toluene. X-ray Diffraction analysis showed that the films exhibited polycrystalline nature of zinc-blende structure with the (111 orientation as the most prominent peak. From the Atomic Force Microscopy, the thickness and surface roughness of the CdTe film increased with the increase of CdTe concentration. The optical energy band gap of film decreased with the increase of CdTe concentration, and with the increase of isothermal bath temperature. The film thickness increased with respect to the increase of CdTe concentration and bath temperature, and following, the numerical expression for the film thickness with respect to these two variables has been established.

  11. Deposition of Boron in Possible Evaporite Deposits in Gale Crate

    Science.gov (United States)

    Gasda, P. J.; Peets, E.; Lamm, S. N.; Rapin, W.; Lanza, N.; Frydenvang, J.; Clark, B. C.; Herkenhoff, K. E.; Bridges, J.; Schwenzer, S. P.; Haldeman, E. B.; Wiens, R. C.; Maurice, S.; Clegg, S. M.; Delapp, D.; Sanford, V.; Bodine, M. R.; McInroy, R.

    2017-12-01

    Boron has been previously detected in Gale crater using the ChemCam instrument on board the NASA Curiosity rover within calcium sulfate fracture fill hosted by lacustrine mudstone and eolian sandstone units. Recent results show that up to 300 ppm B is present in the upper sections of the lacustrine unit. Boron has been detected in both the groundwater-emplaced calcium sulfate fracture fill materials and bedding-parallel calcium sulfate layers. The widespread bedding-parallel calcium sulfate layers within the upper strata of the lacustrine bedrock that Curiosity has encountered recently could be interpreted as primary evaporite deposits. We have two hypotheses for the history of boron in Gale crater. In both hypotheses, borates were first deposited as lake water evaporated, depositing primary evaporates that were later re-dissolved by groundwater, which redistributed the boron into secondary evaporitic calcium sulfate fracture fill deposits. In the first scenario, Gale crater may have undergone a period of perennial lake formation during a drier period of martian history, depositing layers of evaporitic minerals (including borates) among lacustrine mudstone layers. In the second scenario, lake margins could have become periodically exposed during cyclic drops in lake level and subsequently desiccated. Evaporites were deposited and desiccation features were formed in lowstand deposits. Either hypothetical scenario of evaporite deposition would promote prebiotic chemical reactions via wet-dry cycles. Boron may be an important prebiotic element, and as such, its presence in ancient martian surface and groundwater provides evidence that important prebiotic chemical reactions could occur on Mars if organics were present. The presence of boron in ancient Gale crater groundwater also provides additional evidence that a habitable environment existed in the martian subsurface well after the expected disappearance of liquid water on the surface of Mars. We will report on the

  12. Hereditary iron and copper deposition

    DEFF Research Database (Denmark)

    Aaseth, Jan; Flaten, Trond Peder; Andersen, Ole

    2007-01-01

    Hereditary deposition of iron (primary haemochromatosis) or copper (Wilson's disease) are autosomal recessive metabolic disease characterized by progressive liver pathology and subsequent involvement of various other organs. The prevalence of primary haemochromatosis is approximately 0.5%, about...

  13. Types of hydrogenic uranium deposits

    International Nuclear Information System (INIS)

    Kondrat'eva, I.A.; Lisitsin, A.K.; Komarova, G.V.

    1980-01-01

    Principles of uranium deposit systematics are considered. Systematization, presented in this paper, is based on a regularity that the main industrial exogenic epigenetic uranium concentrations are formed in zones of reduction geochemical barriers. Types of uranium-bearing ground waters and nature of uranium reducing agents were taken into account during systematization. Hydrogenic uranium deposits are related to 3 types: formed by ground (1 type), stratal (2 type) and vein (3 type) waters. By the nature of uranium reducing agents 2 deposit subtypes are marked out: A - in rocks with syngenetic reducing agents, B - in rocks with epigenetic reducing agents. Uranium deposits are also differentiated by nature of reducing agents distribution in ore-containing rocks [ru

  14. Atomic layer deposition for semiconductors

    CERN Document Server

    Hwang, Cheol Seong

    2014-01-01

    This edited volume discusses atomic layer deposition (ALD) for all modern semiconductor devices, moving from the basic chemistry of ALD and modeling of ALD processes to sections on ALD for memories, logic devices, and machines.

  15. Fundamental study on repairing technique for cracked or damaged parts of structures by cold gas dynamic spray technique

    International Nuclear Information System (INIS)

    Ogawa, Kazuhiro; Amao, Satoshi; Ichikawa, Yuji; Shoji, Tetsuo

    2008-01-01

    This study proposes an innovative technique for repairing of cracked or damaged parts of structures, such as nuclear or thermal power plants, by means of cold gas dynamic spray (CS) technique. In the case of generation of cracks etc. in the structure, the cracks can be repaired by welding. However, the welding spends considerable time on repair, and also needs special skills. The CS technique is known as a new technique not only for coatings but also for thick depositions. It has many advantages, i.e. dense deposition, high deposition rate and low oxidation. Therefore, it has a possibility to apply the CS technique instead of welding to repair the cracks etc. In this study, the cold gas dynamic spray technique as a new repairing technique for some structures is introduced. (author)

  16. Uranium deposits in volcanic rocks

    International Nuclear Information System (INIS)

    1985-01-01

    Twenty-eight papers were presented at the meeting and two additional papers were provided. Three panels were organized to consider the specific aspects of the genesis of uranium deposits in volcanic rocks, recognition criteria for the characterization of such deposits, and approaches to exploration. The papers presented and the findings of the panels are included in the Proceedings. Separate abstracts were prepared for each of these papers

  17. Electrospark deposition for die repair

    Directory of Open Access Journals (Sweden)

    J. Tušek

    2012-01-01

    Full Text Available The electrospark deposition is a process for surfacing of hard metal alloys, e.g. carbides and stellites, on the surfaces of new or old machine elements. In this process, a high current is conducted through an oscillating electrode and a substrate for a very short period of time. In the paper, the process is described and the thickness of deposited layer, chemical composition, dilution rate and the layer roughness are determined.

  18. Determination of the Young's modulus of pulsed laser deposited epitaxial PZT thin films

    NARCIS (Netherlands)

    Nazeer, H.; Nguyen, Duc Minh; Woldering, L.A.; Abelmann, Leon; Rijnders, Augustinus J.H.M.; Elwenspoek, Michael Curt

    2011-01-01

    We determined the Young’s modulus of pulsed laser deposited epitaxially grown PbZr0.52Ti0.48O3 (PZT) thin films on microcantilevers by measuring the difference in cantilever resonance frequency before and after deposition. By carefully optimizing the accuracy of this technique, we were able to show

  19. Microstructure of Ti6Al4V reinforced by coating W particles through laser metal deposition

    CSIR Research Space (South Africa)

    Ndou, N

    2016-10-01

    Full Text Available The study of laser power on the deposited of Ti64l4V/W was investigated. The laser metal deposition technique has proven to be a process that is sustainable. The microstructure and microhardness properties of a Tungsten powder strengthened composite...

  20. Legal Deposit of Electronic Publications

    Directory of Open Access Journals (Sweden)

    Burcu Umut Zan

    2009-06-01

    Full Text Available The most important and basic role of the deposition studies, which are the greatest contributions to the knowledge sharing, is to gather the artistic and philosophical works of a country and provide them for the use of future researchers. However, since early deposition studies were limited with printed publications, they do not involve the electronic publication types appearing with the development of information technology. This stems from the fact that the electronic publications require procedures different from those of the printed publications in terms of deposition steps because of their structures. Today, in order to guarantee that all registered cultural products, which are mostly produced and used in the electronic environment could be fully collected, electronic publications should also be covered by and regulated under legal deposit. This study analyzes the deposition of electronic publications, within the framework of their storage and protection, being put in the use of the users as well as the common approaches to deposition practices in the world parallel to the developments in the information technology. The related situation in Turkey was also evaluated.

  1. Corrosion and deposit evaluation in large diameter pipes using radiography

    International Nuclear Information System (INIS)

    Boateng, A.

    2012-01-01

    The reliability and safety of industrial equipment in the factories and processing industries are substantially influenced by degradation processes such as corrosion, erosion, deposits and blocking of pipes. These might lead to low production, unpredictable and costly shutdowns due to repair and replacement and sometimes combined environmental pollution and risk of personnel injuries. Only periodic inspection for the integrity of pipes and equipment can reduce the risk in connection with other maintenance activities. The research explored two methods of radiographic inspection techniques, the double wall technique and the tangential radiographic technique using Ir-192 for evaluating deposits and corrosion attacks across the inner and outer walls of steel pipes with diameter greater than 150 mm with or without insulation. The application of both techniques was conducted depending on pipe diameter, wall thickness, radiation source (Ir-92) and film combination. The iridium source was positioned perpendicular with respect to the pipe axis projecting the double wall of the pipe on the plated radiographic film. With the tangential radiographic technique, the source was placed tangential to the pipe wall and because of its large diameter, the source was collimated to prevent backscatter and also to focus the beam at the target area of interest. All measurements were performed on special designed test pieces to simulate corrosion attack and deposits on industrial pipes. Pitting corrosion measurements based on Tangential Radiographic Technique were more sophisticated, and therefore magnification factor and correction were used to establish the estimated pit depth on the film. The insulating material used to conserve the thermodynamic properties of the transported media had relatively negligible attenuation coefficient compared to the concrete deposit. The two explored techniques were successful in evaluating corrosion attack and deposit on the walls of the pipe and the risk

  2. Sistema RTP: uma técnica poderosa para o monitoramento da formação de nanotubos de carbono durante o processo por deposição de vapor químico TPR system: a powerful technique to monitor carbon nanotube formation during chemical vapour deposition

    Directory of Open Access Journals (Sweden)

    Juliana Cristina Tristão

    2010-01-01

    Full Text Available In this work, a TPR (Temperature Programmed Reduction system is used as a powerful tool to monitor carbon nanotubes production during CVD (Chemical Vapour Deposition, The experiments were carried out using catalyst precursors based on Fe-Mo supported on Al2O3 and methane as carbon source. As methane reacts on the Fe metal surface, carbon is deposited and H2 is produced. TPR is very sensitive to the presence of H2 and affords information on the temperature where catalyst is active to form different forms of carbon, the reaction kinetics, the catalyst deactivation and carbon yields.

  3. Integrated Electronic Microscopy Method to Characterize BWR Crud Deposits

    International Nuclear Information System (INIS)

    Pop, Mike G.; Lockamon, Brian; Howe, James M.; Oleshko, Vladimir P.

    2007-01-01

    The primary objective of this paper is to present the best combination of analytical Electron Microscopy (EM) techniques suited for studying Boiling Water Reactor (BWR) fuel crud deposits in their 'as found' condition, for example un-adulterated portions of the deposits located in crevices at the surface of deposit. The secondary objective of the paper is to suggest a strategy to connect the analytical EM results with the Power Diffraction File (PDF-4) crystal database to ultimately explain crystal growth phenomena in crevices. The samples analyzed as part of this work were collected from steam generators in Nuclear Power Plants. These samples were selected as segregates for BWR deposits due to their similar structures and because they were freely releasable for study in the University labs. The samples were analyzed extensively through various EM techniques at magnifications up to 150,000 X. Subsequent evaluation of the analysis results demonstrated that the selected samples exhibited characteristics that were very close to second-burned fuel crud deposits from operating BWR plants. (authors)

  4. Combinatorial techniques

    CERN Document Server

    Sane, Sharad S

    2013-01-01

    This is a basic text on combinatorics that deals with all the three aspects of the discipline: tricks, techniques and theory, and attempts to blend them. The book has several distinctive features. Probability and random variables with their interconnections to permutations are discussed. The theme of parity has been specially included and it covers applications ranging from solving the Nim game to the quadratic reciprocity law. Chapters related to geometry include triangulations and Sperner's theorem, classification of regular polytopes, tilings and an introduction to the Eulcidean Ramsey theory. Material on group actions covers Sylow theory, automorphism groups and a classification of finite subgroups of orthogonal groups. All chapters have a large number of exercises with varying degrees of difficulty, ranging from material suitable for Mathematical Olympiads to research.

  5. Investigation of ferroelectric effects in two sulfide deposits1

    Science.gov (United States)

    Corry, Charles E.

    1994-04-01

    Laboratory studies by different investigators using various techniques have expanded the number of known ferroelectric ore minerals to about twenty at present from the first discovery of makedonite (PbTiO 3) in 1950. These include such common ore minerals as bismuthinite (Bi 2S 3), cassiterite (SnO 2), chalcocite (Cu 2S), pyrrhotite (Fe 1- xS), and stibnite (Sb 2S 3). Two field investigations of sulfide ore bodies that contain known ferroelectric minerals were undertaken to investigate possible in-situ effects in these deposits. These deposits, at Mount Emmons (38°53'N, 107°03'W), Colorado, and Three R Canyon (31°28'N, 110°46'W) in the Patagonia Mountains, Arizona, demonstrate ferroelectric effects that include directional polarization and apparent resistivity, electrically-excited resonance, and lack of reciprocity. Other phenomena include history-dependent electrical behavior and inductive effects. Ferroelectrics polarize as a function of applied potential. It is much easier to generate a large potential than the high currents commonly used in IP surveys. Thus, in electrical surveys of deposits known, or suspected, to contain ferroelectric minerals it may be advantageous to maximize the applied potential. It may also be relatively easy to induce electrical resonance in these deposits that could provide an inexpensive reconnaissance technique. In IP and CR surveys, ferroelectric effects can mask the deposit since ϱa may approach zero in the polar direction, or chargeability may be undetectable. Phase relations will most likely be uninterpretable in CR surveys over such deposits. In CSAMT surveys, directional resonance effects may preclude depth interpretation. Frequency-dependent inductive and capacitive effects may be observed in CR and CSAMT surveys over deposits containing significant quantities of ferroelectric minerals. Ferroelectricity may also be useful in exploitation efforts for electrical beneficiation during ore processing.

  6. Subcellular localization of calcium deposits during zebrafish (Danio rerio) oogenesis.

    Science.gov (United States)

    Golpour, Amin; Pšenička, Martin; Niksirat, Hamid

    2016-01-01

    Calcium plays prominent roles in regulating a broad range of physiological events in reproduction. The aim of this study was to describe the subcellular distribution of calcium deposits during stages of oogenesis in zebrafish using a combined oxalate-pyroantimonate technique. The oocyte development of zebrafish was categorized into four stages: primary growth, cortical-alveolus, vitellogenic, and maturation, based on morphological criteria. Calcium deposits in the primary growth stage were detected in the cytoplasm, mitochondria, nucleus, and follicular cells. At the cortical-alveolus stage, calcium particles were transported from follicular cells and deposited in the cortical alveoli. In the vitellogenic stage, some cortical alveoli were compacted and transformed from flocculent electron-lucent to electron-dense objects with the progression of the stage. Calcium deposits were transformed from larger to smaller particles, coinciding with compaction of cortical alveoli. In the maturation stage, calcium deposits in all oocyte compartments decreased, with the exception of those in mitochondria. The proportion of area covered by calcium deposits in the mitochondria and cortical alveoli of oocytes at different stages of development was significantly different (poogenesis may contribute to better understanding of its role in oogenesis. Copyright © 2015 Elsevier Ltd. All rights reserved.

  7. Atomic Layer Deposition to Enable the Production, Optimization and Protection of Spaceflight Hardware

    Data.gov (United States)

    National Aeronautics and Space Administration — Atomic Layer Deposition (ALD) a cost effective nano-manufacturing technique allows for the conformal coating of substrates with atomic control in a benign...

  8. Atomic Layer Deposition to Enable the Production, Optimization and Protection of Spaceflight Hardware Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Atomic Layer Deposition (ALD) a cost effective nano-manufacturing technique allows for the conformal coating of substrates with atomic control in a benign...

  9. Atomic Layer Deposition to Enable the Production, Optimization and Protection of Spaceflight Hardware Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Atomic Layer Deposition (ALD) is a cost effective nano-manufacturing technique that allows for the conformal coating of substrates with atomic control in a benign...

  10. Distribution characteristics of co-rich manganese deposits on a seamount in the central Pacific Ocean

    Digital Repository Service at National Institute of Oceanography (India)

    Yamazaki, T.; Sharma, R.

    Distribution characteristics of cobalt-rich manganese deposits were evaluated from stereo photographs and video data on a seamount in the central Pacific Ocean by image analysis, photogrammetric technique, and visual observations. The results show...

  11. Nanostructured Electrodes Via Electrostatic Spray Deposition for Energy Storage System

    KAUST Repository

    Chen, C.

    2014-10-02

    Energy storage systems such as Li-ion batteries and supercapacitors are extremely important in today’s society, and have been widely used as the energy and power sources for portable electronics, electrical vehicles and hybrid electrical vehicles. A lot of research has focused on improving their performance; however, many crucial challenges need to be addressed to obtain high performance electrode materials for further applications. Recently, the electrostatic spray deposition (ESD) technique has attracted great interest to satisfy the goals. Due to its many advantages, the ESD technique shows promising prospects compared to other conventional deposition techniques. In this paper, our recent research outcomes related to the ESD derived anodes for Li-ion batteries and other applications is summarized and discussed.

  12. Glancing angle deposition of thin films engineering the nanoscale

    CERN Document Server

    Hawkeye, Matthew M; Brett, Michael J

    2014-01-01

    This book provides a highly practical treatment of GLAD technology, gathering existing procedures, methodologies, and experimental designs into a single, cohesive volume which will be useful both as a ready reference for those in the field and as a definitive guide for those entering it. It covers: History and development of GLAD techniquesProperties and Characterization of GLAD fabricated filmsDesign and engineering of optical GLAD films including fabrication and testingPost-deposition processing and integrationDeposition systems for GLAD fabrication Also includes a patent survey of relevant literature and a survey of GLAD's wide range of material properties and diverse applications.

  13. Solid gold nanostructures fabricated by electron beam deposition

    DEFF Research Database (Denmark)

    Mølhave, Kristian; Madsen, Dorte Nørgaard; Rasmussen, A.M.

    2003-01-01

    and bridges. Transmission electron microscopy was used to study how the composition of these structures was affected when the background gas in the ESEM chamber and the electron beam parameters were varied. The nanostructures were layered composites of up to three different materials each characterized...... by a certain range of gold/carbon ratios. Above a certain threshold of ESEM chamber water vapor pressure and a certain threshold of electron beam current, the deposited tips contained a solid polycrystalline gold core. The deposition technique was used to fabricate free-standing nanowires and to solder free...

  14. Note: the influence of exploding foil shape on energy deposition.

    Science.gov (United States)

    Zeng, Qingxuan; Lv, Junjun; Li, Mingyu

    2013-06-01

    The main influence factors of exploding bridge foil were studied in order to improve energy utilization of the explosion foil initiator. "Square" and "curving" shaped bridge foils were fabricated using magnetron sputtering and chemical etching techniques, and the key dimension of the bridge foil was measured using surface profiler. Commercial software MATLAB was employed to calculate the burst current, burst voltage, and energy deposition. Simulation results were in good agreement with experiment data. In this study, the energy deposition ratio of "square" shaped bridge is between 45%-50%, while the value of "curving" shaped bridge is between 55%-75%.

  15. Combustion chemical vapor deposited coatings for thermal barrier coating systems

    Energy Technology Data Exchange (ETDEWEB)

    Hampikian, J.M.; Carter, W.B. [Georgia Institute of Technology, Atlanta, GA (United States). School of Materials Science and Engineering

    1995-12-31

    The new deposition process, combustion chemical vapor deposition, shows a great deal of promise in the area of thermal barrier coating systems. This technique produces dense, adherent coatings, and does not require a reaction chamber. Coatings can therefore be applied in the open atmosphere. The process is potentially suitable for producing high quality CVD coatings for use as interlayers between the bond coat and thermal barrier coating, and/or as overlayers, on top of thermal barrier coatings. In this report, the evaluation of alumina and ceria coatings on a nickel-chromium alloy is described.

  16. Broadband infrared absorption enhancement by electroless-deposited silver nanoparticles

    DEFF Research Database (Denmark)

    Gritti, Claudia; Raza, Søren; Kadkhodazadeh, Shima

    2017-01-01

    Decorating semiconductor surfaces with plasmonic nanoparticles (NPs) is considered a viable solution for enhancing the absorptive properties of photovoltaic and photodetecting devices. We propose to deposit silver NPs on top of a semiconductor wafer by a cheap and fast electroless plating technique......, which points to the possible applications of such deposition method for harvesting photons in nanophotonics and photovoltaics. The broadband absorption is a consequence of the resonant behavior of particles with different shapes and sizes, which strongly localize the incident light at the interface...

  17. Ash Deposit Formation and Deposit Properties. A Comprehensive Summary of Research Conducted at Sandia's Combustion Research Facility

    Energy Technology Data Exchange (ETDEWEB)

    Larry L. Baxter

    2000-08-01

    This report summarizes experimental and theoretical work performed at Sandia's Combustion Research Facility over the past eight years on the fate of inorganic material during coal combustion. This work has been done under four broad categories: coal characterization, fly ash formation, ash deposition, and deposit property development. The objective was to provide sufficient understanding of these four areas to be able to predict coal behavior in current and advanced conversion systems. This work has led to new characterization techniques for fuels that provide, for the first time, systematic and species specific information regarding the inorganic material. The transformations of inorganic material during combustion can be described in terms of the net effects of the transformations of these individual species. Deposit formation mechanisms provide a framework for predicting deposition rates for abroad range of particle sizes. Predictions based on these rates many times are quite accurate although there are important exceptions. A rigorous framework for evaluating deposit has been established. Substantial data have been obtained with which to exercise this framework, but this portion of the work is less mature than is any other. Accurate prediction of deposit properties as functions of fuel properties, boiler design, and boiler operating conditions represents the single most critical area where additional research is needed.

  18. Uniform deposition of uranium hexafluoride (UF6): Standardized mass deposits and controlled isotopic ratios using a thermal fluorination method.

    Science.gov (United States)

    McNamara, Bruce K; O'Hara, Matthew J; Casella, Andrew M; Carter, Jennifer C; Addleman, R Shane; MacFarlan, Paul J

    2016-07-01

    We report a convenient method for the generation of volatile uranium hexafluoride (UF6) from solid uranium oxides and other U compounds, followed by uniform deposition of low levels of UF6 onto sampling coupons. Under laminar flow conditions, UF6 is shown to interact with surfaces within a fixed reactor geometry to a highly predictable degree. We demonstrate the preparation of U deposits that range between approximately 0.01 and 500ngcm(-2). The data suggest the method can be extended to creating depositions at the sub-picogramcm(-2) level. The isotopic composition of the deposits can be customized by selection of the U source materials and we demonstrate a layering technique whereby two U solids, each with a different isotopic composition, are employed to form successive layers of UF6 on a surface. The result is an ultra-thin deposit that bears an isotopic signature that is a composite of the two U sources. The reported deposition method has direct application to the development of unique analytical standards for nuclear safeguards and forensics. Further, the method allows access to very low atomic or molecular coverages of surfaces. Copyright © 2016 Elsevier B.V. All rights reserved.

  19. Uniform deposition of uranium hexafluoride (UF6): Standardized mass deposits and controlled isotopic ratios using a thermal fluorination method

    Energy Technology Data Exchange (ETDEWEB)

    McNamara, Bruce K.; O’Hara, Matthew J.; Casella, Andrew M.; Carter, Jennifer C.; Addleman, R. Shane; MacFarlan, Paul J.

    2016-07-01

    Abstract: We report a convenient method for the generation of volatile uranium hexafluoride (UF6) from solid uranium oxides and other uranium compounds, followed by uniform deposition of low levels of UF6 onto sampling coupons. Under laminar flow conditions, UF6 is shown to interact with surfaces within the chamber to a highly predictable degree. We demonstrate the preparation of uranium deposits that range between ~0.01 and 470±34 ng∙cm-2. The data suggest the method can be extended to creating depositions at the sub-picogram∙cm-2 level. Additionally, the isotopic composition of the deposits can be customized by selection of the uranium source materials. We demonstrate a layering technique whereby two uranium solids, each with a different isotopic composition, are employed to form successive layers of UF6 on a surface. The result is an ultra-thin deposit of UF6 that bears an isotopic signature that is a composite of the two uranium sources. The reported deposition method has direct application to the development of unique analytical standards for nuclear safeguards and forensics.

  20. Resonant infrared pulsed laser deposition of cyclic olefin copolymer films

    Science.gov (United States)

    Singaravelu, S.; Klopf, J. M.; Schriver, K. E.; Park, H. K.; Kelley, M. J.; Haglund, R. F.

    2014-03-01

    Barrier materials on thin-film organic optoelectronic devices inhibit the uptake of water, oxygen, or environmental contaminants, and fabricating them is a major challenge. By definition, these barrier layers must be insoluble, so the usual routes to polymer- or organic-film deposition by spin coating are not problematic. In this paper, we report comparative studies of pulsed laser deposition of cyclic olefin copolymer (COC), an excellent moisture barrier and a model system for a larger class of protective materials that are potentially useful in organic electronic devices, such as organic light-emitting diodes (OLEDs). Thin films of COC were deposited by resonant and nonresonant infrared pulsed laser ablation of solid COC targets, using a free-electron laser tuned to the 3.43 μm C-H stretch of the COC, and a high-intensity nanosecond Q-switched laser operated at 1064 nm. The ablation craters and deposited films were characterized by scanning-electron microscopy, Fourier-transform infrared spectrometry, atomic-force microscopy, high-resolution optical microscopy, and surface profilometry. Thermal-diffusion calculations were performed to determine the temperature rise induced in the film at the C-H resonant wavelength. The results show that resonant infrared pulsed laser deposition (RIR-PLD) is an effective, low-temperature thin-film deposition technique that leads to evaporation and deposition of intact molecules in homogeneous, smooth films. Nonresonant PLD, on the other hand, leads to photothermal damage, degradation of the COC polymers, and to the deposition only of particulates.