Power generation from lignite coal in Bulgaria - problems and solutions

International Nuclear Information System (INIS)

Batov, S.; Gadjanov, P.; Panchev, T.

1997-01-01

The bulk of lignite coal produced in Bulgaria is used as fuel for the thermal power plants (TPP) built in Maritsa East coal field. A small part of it goes to production of briquettes and to fuel the auxiliary power plants of industrial enterprises. The total installed capacity of the power plants in the region of Maritsa East is 2490 MW, and the electric power generated by them is about 30% of the total power generated in the country. It should be noted that these power plants were subjected to a number of rehabilitations aiming to improve their technical and economic parameters. Irrespective of that, however, solution has still to be sought to a number of problems related to utilisation of the low-grade lignite coal for power generation. On the whole, they can be divided in the following groups: Those related to lignite coal mining can be referred to the first group. Lignite coal is mined in comparatively complicated mining and geological conditions characterized mainly by earth creep and deformation. The second group of problems is related to coal quality control. It is a fact of major significance that the quality indices of coal keep changing all the time in uneven steps without any definite laws to govern it. That creates hard problems in the process of coal transportation, crushing and combustion. The next group of problems concerns operation and upgrading of the power generation equipment. That applies especially to the existing boilers which bum low-grade fuel in order to improve their operation in terms of higher thermal efficiency, controllability, reliability, improved environmental indices, etc. An increasingly high importance is attached to environmental impact problems incident to lignite coal utilisation. Abatement of sulphur oxide emissions and dust pollution is a problem solution of which cannot wait. The possibilities for partial solution of the environmental problems through increasing the thermal efficiency of facilities at the thermal Power

Treatment of lignite tars, etc

Energy Technology Data Exchange (ETDEWEB)

1936-08-07

A process is described for treating tars such as lignite tar, shale tar, or peat tar, and similar tars, characterized by the fact that the tar is rectified to about 240/sup 0/C and the residue brought to a temperature above 50/sup 0/C after diluting with a product of the type of gasoline or ligroin at about 30/sup 0/C and treated with selective solvents preferably low-boiling phenols and eventually with water.

A modern thermal power station operating on high-moisture lignite

Energy Technology Data Exchange (ETDEWEB)

V.R. Kotler; D.V. Sosin [All-Russia Thermal Engineering Institute (VTI), Moscow (Russian Federation)

2009-07-01

The boilers developed by the power machinery construction company Alstom for two power-generating units, the Maritsa East-II and Maritsa East-II, operating on high-moisture lignite from the Maritsa East field in Bulgaria are described.

Lignite Fuel Enhancement

Energy Technology Data Exchange (ETDEWEB)

Charles Bullinger; Nenad Sarunac

2010-03-31

Pulverized coal power plants which fire lignites and other low-rank high-moisture coals generally operate with reduced efficiencies and increased stack emissions due to the impacts of high fuel moisture on stack heat loss and pulverizer and fan power. A process that uses plant waste heat sources to evaporate a portion of the fuel moisture from the lignite feedstock in a moving bed fluidized bed dryer (FBD) was developed in the U.S. by a team led by Great River Energy (GRE). The demonstration was conducted with Department of Energy (DOE) funding under DOE Award Number DE-FC26-04NT41763. The objectives of GRE's Lignite Fuel Enhancement project were to demonstrate reduction in lignite moisture content by using heat rejected from the power plant, apply technology at full scale at Coal Creek Station (CCS), and commercialize it. The Coal Creek Project has involved several stages, beginning with lignite drying tests in a laboratory-scale FBD at the Energy Research Center (ERC) and development of theoretical models for predicting dryer performance. Using results from these early stage research efforts, GRE built a 2 ton/hour pilot-scale dryer, and a 75 ton/hour prototype drying system at Coal Creek Station. Operated over a range of drying conditions, the results from the pilot-scale and prototype-scale dryers confirmed the performance of the basic dryer design concept and provided the knowledge base needed to scale the process up to commercial size. Phase 2 of the GRE's Lignite Fuel Enhancement project included design, construction and integration of a full-scale commercial coal drying system (four FBDs per unit) with Coal Creek Units 1 and 2 heat sources and coal handling system. Two series of controlled tests were conducted at Coal Creek Unit 1 with wet and dried lignite to determine effect of dried lignite on unit performance and emissions. Wet lignite was fired during the first, wet baseline, test series conducted in September 2009. The second test series was

The structure and pyrolysis product distribution of lignite from different sedimentary environment

International Nuclear Information System (INIS)

Liu, Peng; Zhang, Dexiang; Wang, Lanlan; Zhou, Yang; Pan, Tieying; Lu, Xilan

2016-01-01

Highlights: • Carbon structure of three lignites was measured by solid "1"3C NMR. • Effect of carbon structure on pyrolysis product distribution was studied. • Tar yield is influenced by aliphatic carbon and oxygen functional group. • C1–C4 content of pyrolysis gas is related to CH_2/CH_3 ratio. - Abstract: Low-temperature pyrolysis is an economically efficient method for lignite to obtain coal tar and improve its combustion calorific value. The research on the distribution of pyrolysis product (especially coal tar yield) plays an important role in energy application and economic development in the now and future. Pyrolysis test was carried out in a tube reactor at 873 K for 15 min. The structure of the lignite was measured by solid "1"3C nuclear magnetic resonance (NMR) and Fourier transform infrared spectroscopy (FTIR). The thermal analysis was analyzed by thermo-gravimetric (TG) analyzer. The results show that the pyrolysis product distribution is related to the breakage of branch structures of aromatic ring in lignites from different sedimentary environment. The gas yield and composition are related to the decomposition of carbonyl group and the breakage of aliphatic carbon. The tar yield derived from lignite pyrolysis follows the order: Xianfeng lignite (XF, 13.67 wt.%) > Xiaolongtan lignite (XLT, 7.97 wt.%) > Inner Mongolia lignite (IM, 6.30 wt.%), which is mainly influenced by the aliphatic carbon contents, the CH_2/CH_3 ratio and the oxygen functional groups in lignite. The pyrolysis water yield depends on the decomposition of oxygen functional groups. IM has the highest content of oxygen-linked carbon so that the pyrolysis water yield derived from IM is the highest (9.20 wt.%), and is far more than that from the other two lignites.

Technology and use of lignite. Proceedings of the tenth biennial lignite symposium

Energy Technology Data Exchange (ETDEWEB)

Kube, W. R.; Gronhovd, G. H. [comps.

1979-01-01

The symposium on the technology and use of lignite was sponsored by the US Department of Energy and the University of North Dakota, and held at Grand Forks, North Dakota, May 30-31, 1979. Twenty-one papers from the proceedings of this tenth biennial lignite symposium have been entered into EDB and ERA and three also into EAPA. The papers discuss lignite deposits in the USA, mining plans, gasification and in-situ gasification, and combustion in fossil-fuel power plants. (LTN)

The North Dakota lignite partnership

International Nuclear Information System (INIS)

Porter, C.R.

1998-01-01

The State of North Dakota and the Lignite Energy Council have formed a government/industry partnership to promote the use of North Dakota lignite. The partnership provides funding and management for the Lignite Research, Development and Marketing Program. The program funds activities which preserve and enhance jobs and lignite production; ensure economic growth, stability and opportunity; and maintain a stable and competitive tax base. Funding is provided for activities in three areas: marketing feasibility studies, small research projects, and demonstration projects. Funding is derived from the state coal severance tax. Approximately $3,000,000 annually is appropriated from coal severance revenues for program activities. North Dakota is the ninth largest coal producing state, with lignite as the only rank of coal found in the state. Energy is the second largest economic sector in North Dakota, and it currently comprises over 12% of the state's total economic base. This paper reviews the North Dakota lignite industry and describes studies and projects which have received funding from the program

Lignite in North Dakota

International Nuclear Information System (INIS)

Porter, C.R.

1995-01-01

The State of North Dakota and the lignite industry are working together in a partnership called the Lignite Research, Development and Marketing Program. The program provides funds and supports activities which: preserve and enhance jobs and lignite production; ensure economic growth, stability and opportunity; and maintain a stable and competitive tax base. Since 1987, 70 grants totaling $24 million have been awarded. Each program dollar has resulted in nearly five of matching dollars. These program investments have yielded returns for the state and industry, including an additional $20 million annually from by-products at the Great Plains Synfuels Plant; about $1 million annually from improved reclamation practices; and combustion options, which preserve 2,000 megawatts of existing generation capacity. Research activities have identified future opportunities, including: the SynCoal demonstration plant, requiring 800,000 tons per year of new production; new chemical feedstock by-products from Great Plains worth an additional $26 million annually; revised reclamation practices that could substantially reduce cost; and potential new markets for upgraded lignite of about 12 million tons annually. This program helps ensure a healthy future for the North Dakota lignite industry, which currently represents 10% of the state's total economic base. Such a program is important because it will encourage the development of new and better uses of North Dakota's most abundant resource--lignite coal

Lignite; Braunkohle

Energy Technology Data Exchange (ETDEWEB)

Kaltenbach, Erwin; Maassen, Uwe [Debriv e.V., Berlin und Koeln (Germany)

2015-07-01

The domestic lignite is the most important and in the foreseeable future, the only domestic energy resource that is available in large quantities and economically. It makes an essential contribution to secure and competitive energy supply and has a high regional as macroeconomic importance. The required guarantied capacity for the development of renewable energy, the lignite provides under competition conditions. The flexibility of the lignite power plants is in addition to security of supply and competitiveness, a strategic added value for a reliable power supply. [German] Die heimische Braunkohle ist die wichtigste und in ueberschaubarer Zukunft auch die einzige heimische Energieressource, die in grossen Mengen und wirtschaftlich zur Verfuegung steht. Sie leistet einen unverzichtbaren Beitrag zur sicheren und wettbewerbsfaehigen Energieversorgung und hat eine hohe regional- wie gesamtwirtschaftliche Bedeutung. Die fuer den Ausbau der erneuerbaren Energien notwendige gesicherte Leistung stellt die Braunkohle unter Wettbewerbsbedingungen zur Verfuegung. Die Flexibilitaet des Braunkohlenkraftwerksparks ist neben Versorgungssicherheit und Wettbewerbsfaehigkeit ein strategischer Zusatznutzen fuer eine sichere Stromversorgung.

Externalities from lignite mining-related dust emissions

International Nuclear Information System (INIS)

Papagiannis, A.; Roussos, D.; Menegaki, M.; Damigos, D.

2014-01-01

During the last three decades, several studies have been conducted in order to assess the external costs of electricity production from fossil fuels, especially coal and lignite. Nevertheless, these studies usually ignore the impacts generated by the upstream mining works. This paper contributes to existing literature and attempts to fill this gap by exploring the externalities of lignite mining owing to the emission of suspended particulate matter. To this end, a ‘bottom-up’ approach is implemented, using as case study the largest operational lignite surface mine at the Lignite Center of Western Macedonia (Greece). The results indicate that annual air pollution externalities of lignite mining are of the order of 3€/ton of lignite, which corresponds to around 5.0 €/MW h. The estimated costs are significantly lower, i.e. up to 80%, when dust deposition is considered in air dispersion models. In any case, these findings should be seen as a starting point for discussion owing to the lack of specific emission rates for Greek lignite mines. - Highlights: • Externalities from lignite mining-related dust emissions are 3 €/t of lignite. • Externalities of mining correspond to around 5.0 €/MW h. • Externalities are significantly lower, up to 80%, if dust deposition is considered. • There is lack of specific dust emission rates for lignite mining. • There are high discrepancies in existing dust emission rates for lignite mining

Co-pyrolysis of lignite and sugar beet pulp

International Nuclear Information System (INIS)

Yilgin, M.; Deveci Duranay, N.; Pehlivan, D.

2010-01-01

Today, worldwide studies have been undertaken on the biomass usage and co-conversion of biomass and coal to seek out alternative fuels for supplying energy in an environmental friendly way. The objective of this work is to study co-pyrolysis of lignite and sugar beet pulp in 50/50 (wt./wt.) ratio of blend pellets, to elucidate their thermal behaviour under pyrolysis conditions and to assess major decomposition products in terms of their yields. A special chamber, which has enabled very fast heating rates, was used in the pyrolysis experiments carried at 600 deg. C. The results were interpreted in the light of liquid, solid and gaseous yields, resulting from thermal decomposition, and kinetics of thermogravimetric analysis. Proximate volatile matter and ash contents of the blends were different compared to those found by using individual values. Sugar beet pulp decomposed faster within a relatively narrow temperature range than lignite and underwent a significant shrinkage during pyrolysis. It was found that the chars left behind after the flash pyrolysis of these pellets at 600 deg. C have substantial amounts of volatile matter that would evolve upon further heating.

THE COMBUSTION CHARACTERISTICS OF LIGNITE BLENDS

Institute of Scientific and Technical Information of China (English)

Cheng Jun; Zhou Junhu; Cao Xinyu; Cen Kefa

2000-01-01

The combustion characteristics of lignite blends were studied with a thermogravimetric analyzer (t.g.a.), at constant heating rate.The characteristic temperatures were determined from the burning profiles.It was found that the characteristic times of combustion reaction moved forward, the ignition temperature dropped and the burnout efficiency slightly changed when blending lignites.The characteristic parameters of blends could not be predicted as a linear function of the average values of the individual lignites.when blending with less reactive coal, the ignition and burnout characteristics of lignite turned worse.

Possibilities of utilizing the Hungarian reserves of lignite in thermal power stations

Energy Technology Data Exchange (ETDEWEB)

Faur, G

1978-01-01

The Upper Pannonian lignite reserves subjected to study are suited to opencast mining with respect to their depth and thickness. All of them are characterized by occurrence in multiple beds, the thickness of which however is different per area. The dirt between the strata consists mostly of sand, to a lesser degree of clay or of materials between the former. Continuously operating dredges can be used for working, the types depending on the thickness of the overburden and the technology to be applied. Deep wells with submerged pumps may be employed for drainage. High-capacity mining districts can be operated at the areas subjected to study, new districts must however be opened up to increase the productive capacity beyond a certain limit. Establishment of a significant power station capacity is made possible by the explored lignite reserves. (In Hungarian)

Radioactivity of Yatagan lignites and their ash

International Nuclear Information System (INIS)

Cicek, F.; Mustafaev, I.; Aliyev, C.

2004-01-01

Full text: One of harmful factor of Environmental impact of coal combustion is radiation pollution of Environment. The natural radioisotopes - uranium, thorium and potassium and products of their radioactive destruction contains of radionuclides. These radionuclides in composition of fly ash are thrown to atmosphere from coal combustion furnaces. The concentration of radioisotopes in composition of coals changes in the wide ranges: from 3 up to 520 Becquerel per kilogram (Bq/kg) for Uranium-238 and from 3 up to 320 Bq/kg for thorium-232. The radioactive pollution degree of environment depends on radioisotopes content of initial fuels. In this connection at the estimation of outlook and exploitation of coal mines it is necessary to determine of radioisotopes concentration in coals. That is why investigation of radioisotopes concentration of Turkish lignites has great importance. In this work the radionuclide content of Yatagan lignites and their ash, taken from Gekova thermal Electro station have been studied. The total radiation background generated by these samples was investigated by using of dosimeters 8P-5, CRP-88H, PYB-OIP. Radionuclides content of samples was determined in the Institute of Geology Azerbaijan national Academy of Sciences by using of highly sensitivity gamma-spectrometer CAPU-2, designed by Special Constructor Buro G eophysika . The plant allows to determine the radioisotopes content of solid and liquid samples with highly reliability. It has been established that in sample of lignite uranium content (on the radium equivalent) is 68 Bq/kg, potassium-149 Bq/kg and thorium is absent. The total radioactivity of lignite sample is 79,7 Bq/kg. In the ash sample uranium content is 266 Bq/kg, potassium-188 Bq/kg, and total activity reach to 300 Bq/kg. The possibility of application of purification erection for radionuclides from smoke gases of coal combustion is discussed

Lignite boost for North. [Northern Ireland

Energy Technology Data Exchange (ETDEWEB)

Clerkin, H.

1986-01-01

Reserves of lignite, estimated at around 500 million tonnes, have been discovered on the shores of Lough Neagh, Northern Ireland. The Government has granted a mining licence and planning permission to Burnett and Hallamshire Holdings to start work on the deposit. It is proposed to mine the lignite using opencast methods. Much of this deposit will be consumed in a purpose-built mine mouth power station with further reserves being dried in the approved processing plant to produce a range of industrial and domestic fuels. Carbonising the lignite may eliminate pollution. However, large scale investment will be required before Ireland's economy can switch to lignite.

Catalytic cracking of lignites

Energy Technology Data Exchange (ETDEWEB)

Seitz, M.; Nowak, S.; Naegler, T.; Zimmermann, J. [Hochschule Merseburg (Germany); Welscher, J.; Schwieger, W. [Erlangen-Nuernberg Univ. (Germany); Hahn, T. [Halle-Wittenberg Univ., Halle (Germany)

2013-11-01

A most important factor for the chemical industry is the availability of cheap raw materials. As the oil price of crude oil is rising alternative feedstocks like coal are coming into focus. This work, the catalytic cracking of lignite is part of the alliance ibi (innovative Braunkohlenintegration) to use lignite as a raw material to produce chemicals. With this new one step process without an input of external hydrogen, mostly propylene, butenes and aromatics and char are formed. The product yield depends on manifold process parameters. The use of acid catalysts (zeolites like MFI) shows the highest amount of the desired products. Hydrogen rich lignites with a molar H/C ratio of > 1 are to be favoured. Due to primary cracking and secondary reactions the ratio between catalyst and lignite, temperature and residence time are the most important parameter to control the product distribution. Experiments at 500 C in a discontinuous rotary kiln reactor show yields up to 32 wt-% of hydrocarbons per lignite (maf - moisture and ash free) and 43 wt-% char, which can be gasified. Particularly, the yields of propylene and butenes as main products can be enhanced four times to about 8 wt-% by the use of catalysts while the tar yield decreases. In order to develop this innovative process catalyst systems fixed on beads were developed for an easy separation and regeneration of the used catalyst from the formed char. (orig.)

Lignite mining in India - technology highlights

Energy Technology Data Exchange (ETDEWEB)

Tandon, G L

1984-01-01

Figures for lignite production and its role in the Indian energy scene are presented. Lignite mining at Neyveli is described in detail, including: advance preparation of the overburden strata; modifications to bucket wheel excavators; tackling the sticky surface clays; ground water management; storm water control; tackling higher overburden-to-lignite ratios; materials handling; communications within the mine; the development of indigenous mining equipment; and ecology and environmental control.

NOx and SO2 emission factors for Serbian lignite Kolubara

Directory of Open Access Journals (Sweden)

Jovanović Vladimir V.

2012-01-01

Full Text Available Emission factors are widely accepted tool for estimation of various pollutants emissions in USA and EU. Validity of emission factors is strongly related to experimental data on which they are based. This paper is a result of an effort to establish reliable NOx and SO2 emission factors for Serbian coals. The results of NOx and SO2 emissions estimations based on USA and EU emission factors from thermal power plants Nikola Tesla Obrenovac A and B utilizing the Serbian lignite Kolubara are compared with experimental data obtained during almost one decade (2000-2008 of emissions measurements. Experimental data are provided from regular annual emissions measurement along with operational parameters of the boiler and coal (lignite Kolubara ultimate and proximate analysis. Significant deviations of estimated from experimental data were observed for NOx, while the results for SO2 were satisfactory. Afterwards, the estimated and experimental data were plotted and linear regression between them established. Single parameter optimization was performed targeting the ideal slope of the regression line. Results of this optimization provided original NOx and SO2 emission factors for Kolubara lignite.

THERMODYNAMIC ANALYSIS OF CARBON SEQUESTRATION METHODS IN LIGNITE POWER PLANTS

International Nuclear Information System (INIS)

Koroneos J. Christopher; Sakiltzis Christos; Rovas C. Dimitrios

2008-01-01

The green house effect is a very pressing issue of our times due to the big impact it will have in the future of life in our planet. The temperature increase of the earth which is the major impact of the greenhouse effect may change forever the climate and the way of life in many countries. It may lead to the reduction of agricultural production and at the end to famine, in several nations. The minimization of CO2 emissions and the introduction of new energy sources is the only solution to the catastrophe that is coming if inaction prevails. The objective of this work is to analyze the methods of the CO2 removal from the flue gases of power plants that use solid fuels. It is especially fit to the Greek conditions where the main fuel used is lignite. Three methods have been examined and compared thermodynamically. These are: (a) Removal of CO2 from the flue gas stream by absorption, (b) The combustion of lignite with pure oxygen and (c) The gasification of lignite. The lignite used in the analysis is the Greek lignite, produced at the Western Macedonia mines. The power plant, before carbon sequestration, has an efficiency of 39%, producing 330MW of electric power. After sequestration, the CO2 is compressed to pressures between 80-110 atm, before its final disposal. In the first method, the sequestration of CO2 is done utilizing a catalyst. The operation requires electricity and high thermal load which is received from low pressure steam extracted from the turbines. Additionally, electricity is required for the compression of the CO2 to 100 bars. This leads to a lower efficiency of the power plant by by 13%. In the second method, the lignite combustion is done with pure O2 produced at an air separation unit. The flue gasses are made up of CO2 and water vapor. This method requires electricity for carbon dioxide compression and the Air Separation unit, thus, the power plant efficiency is lowered by 26%. In the lignite gasification method, the products are a mixture of

Future of lignite resources: a life cycle analysis.

Science.gov (United States)

Wang, Qingsong; Liu, Wei; Yuan, Xueliang; Zheng, Xiaoning; Zuo, Jian

2016-12-01

Lignite is a low-quality energy source which accounts for 13 % of China's coal reserves. It is imperative to improve the quality of lignite for large-scale utilization. To further explore and analyze the influence of various key processes on the environment and economic costs, a lignite drying and compression technology is evaluated using an integrated approach of life cycle assessment and life cycle costs. Results showed that lignite mining, direct air emissions, and electricity consumption have most significant impacts on the environment. An integrated evaluation of life cycle assessment and life cycle costs showed that the most significant contributor to the environmental impacts and economic costs was the lignite mining process. The impact of transportation and wastewater treatment process on the environment and economic costs was small enough to be ignored. Critical factors were identified for reducing the environmental and economic impacts of lignite drying and compression technology. These findings provide useful inputs for both industrial practice and policy making for exploitation, processing, and utilization of lignite resources.

Lignite pre-treatment and its effect on bio-stimulative properties of respective lignite humic acids

Energy Technology Data Exchange (ETDEWEB)

Vlckova, Z.; Grasset, L.; Antosova, B.; Pekar, M.; Kucerik, J. [Brno University of Technology, Brno (Czech Republic). Faculty of Chemistry

2009-09-15

Humic acids originating from South-Moravian lignite were subjected to a comparative study with the aim to assess the alteration of their physico-chemical properties after various lignite pre-treatments. Physical modification was achieved with two organic acids, such as acetic acid and citric acid and chemical modification by nitric acid and hydrogene peroxide in various concentrations. Elemental analysis, solid-state NMR, GC-MS analysis of polyols and size exclusion chromatography were carried out for chemical-physical characterization of obtained humic acids. Their biological effect, in form of potassium and ammonium humates, was tested on maize (Zea mays) seedlings. In these tests, potassium humates achieved far better overall results than ammonium humates. Results were inter-correlated in order to appraise the influence of humic acids physical and chemical properties on biological activity. Surprisingly, fractions with the lowest molecular size (0-35 kDa) showed no correlation with bioactivity results (Pearson coefficient from 0.05 to -0.4). On the contrary, middle-sized fractions (35-175 kDa) showed highly significant positive correlation (Pearson coefficient up to 0.92) and the highest molecular-size-fractions (275-350 kDa) showed negative correlation (Pearson coefficient up to -0.75). These findings were identical for both potassium and ammonium humates. No connection was found between bioactivity of humates and polyols content which was remarkably high; it reached 150 mg per g of humic acids in the most extreme case of 5% hydrogene peroxide pre-treatment. In the final analysis, the preparation mode bore pivotal responsibility for the control of humic acids biological effect and showed the best results for potassium humates obtained from lignite pre-treated by acetic acid and by 2% hydrogen peroxide.

The future path of lignite production in the Balkan countries

International Nuclear Information System (INIS)

Boussios, E.; Koikouzas, N.K.

1997-01-01

The future development of the European Union and Balkan lignite industry is examined in this paper. Lignite in some countries represents for the last decade by far the most important fuel for electricity generation. The economically recoverable lignite reserves of the Balkans (21.36 x 10 9 t) and Greece (4.0 x 10 9 t) are sufficient to meet their energy demand for the next decades (50-100 years). The Balkan countries intended to increase their lignite production, in the near future, as result of the increase of their primary energy demand and their efforts to meet their energy requirements by using domestic resources. Greece also plans to increase lignite production. On the contrary, the remaining of the European Union countries intend to decrease their lignite production. Nevertheless, the countries of Balkan region which are presently in a transition period to the market economy, have to deal with a decrease of people employed in the lignite mining industry. However, Balkan region seems to be the most promising area for the future development of the lignite industry in the enlarged EU, after making the following alterations in the lignite sector: Rehabilitation of the lignite open-pit mines, closure of the most underground mines, privatization of the most prosperous mines, modification of the existing technology, introduction of the 'clean' coal technology, etc. New opportunities for the development and modernization of the lignite industry in Balkan countries arise, after their possible entrance into the European Union, considering also that lignite is one of their most important indigenous energy source. For the necessary modernization of the lignite industry, development of collaborations for the capital and know-how transferring is required. (Author)

Radiation doses of inhaled ash from the lignite power plants

International Nuclear Information System (INIS)

Boshevski, Tome; Pop-Jordanov, Jordan; Chaushevski, Anton

1997-01-01

The coal-fired thermal power plants in Macedonia use lignite obtained by surface mining. The lignite contains traces of thorium-232, uranium-238 and uranium-235, which are long-lived natural radioactive isotopes. After lignite combustion, the concentration of these isotopes in the ash is increased. Due to the long life of fossil materials, the decay products are basically grouped in three radioactive chains that are in a semi-steady state, resulting in equal activity of all isotopes from the chain. Among the members of each chain there are α and β emitters followed by γ quanta emitters. The energies of the α and β particles are important for determining the effective dose. The γ quanta provide information about the chain activity and isotope types. Gamma-spectroscopy studies of the ash samples from the power plants in the City of Bitola in Macedonia have confirmed the presence of several radioactive decay products from the uranium and thorium radioactive chains. Using measurements of the radioactivity of the ash in the Bitola region, the total dose from ash inhalation for the population in the Bitola region was calculated and presented in this paper. Also, analysis of the procedure for determining the maximum allowable dose from radioactive contamination of the environment, is described in this paper. (Original)

A lignite-geothermal hybrid power and hydrogen production plant for green cities and sustainable buildings

Energy Technology Data Exchange (ETDEWEB)

Kilkis, B. [Baskent University, Ankara (Turkey). Dept. of Mechanical Engineering

2011-02-15

Turkey is rich in both geothermal energy and lignite reserves, which in many cases, are co-located. This condition makes it feasible to utilize both lignite and geothermal energy in a hybrid form for combined power heat, and cold generation, which may lead to optimally energy and exergy efficient, environmentally benign, and economically sound applications. This paper presents a novel concept of hybrid lignite-geothermal plant for a district energy system and hydrogen production facility in Aydin with special emphasis on high performance, green buildings and green districts. In this concept, lignite is first introduced to a partially fluidized-bed gasifier and then to a fluidized-bed gas cleaning unit, which produces synthetic gas and finally hydrogen. The by-products, namely char and ash are used in a fluidized-bed combustor to produce power. Waste heat from all these steps are utilized in a district heating system along with heat received from geothermal production wells after power is generated there. H{sub 2}S gas obtained from the separator system is coupled with hydrogen production process at the lignite plant. Absorption cooling systems and thermal storage tanks complement the hybrid system for the tri-generation district energy system. On the demand side, the new, green OSTIM OSB administration building in Ankara is exemplified for greener, low-exergy buildings that will compound the environmental benefits.

Characterisation of lignite as an industrial adsorbent

Energy Technology Data Exchange (ETDEWEB)

Ying Qi; Andrew F.A. Hoadley; Alan L. Chaffee; Gil Garnier [Monash University, Clayton, Vic. (Australia). Department of Chemical Engineering

2011-04-15

An alternative use of the abundant and inexpensive lignite (also known as brown coal) as an industrial adsorbent has been characterised. The adsorptive properties of two Victorian lignite without any pre-treatment were investigated using the cationic methylene blue dye as a model compound in aqueous solutions. Two commercial activated carbon products were also studied for comparison. The adsorption equilibrium of the four adsorbents was better described by the Langmuir isotherm model than the Freundlich model. The adsorption capacities of the two untreated lignite adsorbents, Loy Yang and Yallourn, calculated using Langmuir isotherms were 286 and 370 mg/g, respectively, higher than a coconut shell-based activated carbon (167 mg/g), but lower than a coal-based activated carbon (435 mg/g). Surface area results suggested that larger micropores and mesopores were important for achieving good methylene blue adsorption by the activated carbons. However, FTIR and cation exchange capacity analyses revealed that, for the lignite, chemical interactions between lignite surface functional groups and methylene blue molecules occurred, thereby augmenting its adsorption capacity. 63 refs., 3 figs., 7 tabs.

Lignite As Contributory Factor to Regional Development of Greece

OpenAIRE

Ilias Kordas

2006-01-01

Lignite (brown coal) is Greece's most important energy mineral raw material. Lignite exploitation has made a highly significant contribution to the development of energy sector of Greece on past 50 years, and will, according to estimations, continue to supply energy for another 40 years. Greece is very rich in Lignite resources. The two main basins - from where Lignite is extracted by opencast mining - are a) in Western Macedonia (northen Greece) where is generated the 70% of the whole electr...

Aspects of combustion behaviour of coals from some New Zealand lignite-coal regions determined by thermogravimetry

Energy Technology Data Exchange (ETDEWEB)

Benfell, K.E.; Beamish, B.B.; Rodgers, K.A. [University of Newcastle, Callaghan, NSW (Australia). Dept. of Geology

1997-08-25

The papers describes how thermogravimetric analysis of five Late Cretaceous and Cenozoic New Zealand lignites demonstrate that their combustion behaviour is distinct from that of subbituminous coals and may be characterised by peak temperature of 377-416{degree}C, maximum rate of combustion of 25-31 wt% min{sup -1}, and temperature of char burnout 421-497{degree}C. These parameters reflect variation in thermal behaviour associated with both the organic and inorganic constituents of the coal. The information obtained is additional to that provided by proximate analysis; the latter is insufficient to predict the combustion behaviour of the coals relative to one another. A post-combustion thermal event is seen among the lignites as in other low-rank coals combusting below 600{degree}C, which appears to be related to the organic sulphur content of the coal.

Degradation/solubilization of Chinese lignite by Penicillium sp. P6

Energy Technology Data Exchange (ETDEWEB)

Yuan, H.L.; Yang, J.S.; Wang, F.Q.; Chen, W.X. [China Agricultural University, Beijing (China). Key Laboratory of Agro-Microbial Resource and Application, Ministry of Agrio, College of Biological Science

2006-01-15

Penicillium sp. P6, isolated from coal mine soil at the Qiantong colliery Liaoning Province, Northeast China, can degrade Chinese lignite in 36 h on a plate colony and in 48 h using a 4-day cultured cell-free filtrate. Results of elemental analysis and IR spectrometry indicated that solubilized products exhibited some alterations in comparison to the original lignite. The amount of fulvic acid extracted from the biodegraded lignite was high, and the molecular distribution of the humic acids from biodegraded lignite changed distinctively in comparison to which extracted from the control lignite, possibly due to the depolymerization associated with fungal biodegradation.

Recovery of uranium from lignites

International Nuclear Information System (INIS)

Hurst, F.J.

1980-01-01

Uranium in raw lignite is associated with the organic matter and is readily soluble in acid (and carbonate) solutions. However, beneficiation techniques were not successful for concentrating the uranium or removing part of the reagent-consuming materials. Once the lignite was heated, the uranium became much less soluble in both acid and carbonate solutions, and complete removal of carbon was required to convert it back to a soluble form. Proper burning improves acid-leaching efficiency; that is, it reduces the reagent consumption and concentrates the uranium, thereby reducing plant size for comparable uranium throughput, and it eliminates organic fouling of leach liquors. Restrictions are necessary during burning to prevent the uranium from becoming refractory. The most encouraging results were obtained by flash-burning lignite at 1200 to 1300 0 C and utilizing the released SO 2 to supplement the acid requirement. The major acid consumers were aluminum and iron

Biodegradation of photo-oxidized lignite and characterization of the products

Science.gov (United States)

Li, Jiantao; Liu, Xiangrong; Yue, Zilin; Zhang, Yaowen

2018-01-01

Biodegradation of photo-oxidized Inner Mongolia lignite by pseudomonas aeruginosa was studied and the degradation percentage reached 56.27%, while the corresponding degradation percentage of the strain degrading raw Inner Mongolia lignite is only 23.16%. The degradation products were characterized. Proximate and ultimate analyses show that the higher oxygen content increased by photo-oxidation pretreatment maybe promoted the degradation process. Ultraviolet spectroscopy (UV) analysis of the liquid product reveals that it contains unsaturated structures and aromatic rings are the main structure units. Gas chromatography-mass spectrometry (GC-MS) analysis indicates that the main components of the ethyl acetate extracts are low molecular weight organic compounds, such as ketones, acids, hydrocarbons, esters and alcohols. Infrared spectroscopy (IR) analysis of raw lignite, photo-oxidized lignite and residual lignite demonstrates that the absorption peaks of functional groups in residual lignite disappeared or weakened obviously. Scanning electron microscopy (SEM) analysis manifests that small holes appear in photo-oxidized lignite surface, which may be promote the degradation process and this is only from the physical morphology aspects, so it can be inferred from the tests and analyses results that the more important reason of the high degradation percentage is mostly that the photo-oxidation pretreatment changes the chemical structures of lignite.

Treatment of products from petroleum, shale, coal, lignite, etc

Energy Technology Data Exchange (ETDEWEB)

Jevanoff, V

1952-06-20

An improved process is described for treating with sodium plumbite all the products derived from crude petroleum, bituminous shale, coal, lignite, peat, etc., such as gasoline, solvents, lamp oil, gas oil, fuels, etc; the process being essentially characterized by the fact that it consists first in washing the product to be refined with a soda wash; submitting it to a treatment with sodium plumbite, without addition of sulfur, then to eliminate the sulfur plumbite compounds resulting in the treated product, using either redistillation to eliminate products remaining in the residue or filtration over an absorbing material such as active carbon, decolorizing earths.

Effect of biomass on burnouts of Turkish lignites during co-firing

Energy Technology Data Exchange (ETDEWEB)

Haykiri-Acma, H.; Yaman, S. [Istanbul Technical Univ., Chemical and Metallurgical Engineering Faculty, Chemical Engineering Dept., 34469 Maslak, Istanbul (Turkey)

2009-09-15

Co-firing of some low quality Turkish lignites with woody shells of sunflower seed was investigated via non-isothermal thermogravimetric analysis method. For this purpose, Yozgat-Sorgun, Erzurum-Askale, Tuncbilek, Gediz, and Afsin-Elbistan lignites were selected, and burnouts of these lignites were compared with those of their blends. Biomass was blended as much as 10 and 20 wt.% of the lignites, and heating was performed up to 900 C at a heating rate of 40 C/min under dry air flow of 40 mL/min. This study revealed that the same biomass species may have different influences on the burnout yields of the lignites. Burnouts of Erzurum-Askale lignite increased at any temperature with the increasing ratio of biomass in the blend, whereas burnout yields of other lignites decreased to some extent. Nevertheless, the blends of Turkish lignites with sunflower seed shell did not behave in very different way, and it can be concluded that they are compatible in terms of burnouts for co-combustion in a combustion system. Although the presence of biomass in the lignite blends caused to some decreases in the final burnouts, the carbon dioxide neutral nature of biomass should be taken into account, and co-combustion is preferable for waste-to-energy-management. (author)

Effect of biomass on burnouts of Turkish lignites during co-firing

International Nuclear Information System (INIS)

Haykiri-Acma, H.; Yaman, S.

2009-01-01

Co-firing of some low quality Turkish lignites with woody shells of sunflower seed was investigated via non-isothermal thermogravimetric analysis method. For this purpose, Yozgat-Sorgun, Erzurum-Askale, Tuncbilek, Gediz, and Afsin-Elbistan lignites were selected, and burnouts of these lignites were compared with those of their blends. Biomass was blended as much as 10 and 20 wt.% of the lignites, and heating was performed up to 900 deg. C at a heating rate of 40 deg. C/min under dry air flow of 40 mL/min. This study revealed that the same biomass species may have different influences on the burnout yields of the lignites. Burnouts of Erzurum-Askale lignite increased at any temperature with the increasing ratio of biomass in the blend, whereas burnout yields of other lignites decreased to some extent. Nevertheless, the blends of Turkish lignites with sunflower seed shell did not behave in very different way, and it can be concluded that they are compatible in terms of burnouts for co-combustion in a combustion system. Although the presence of biomass in the lignite blends caused to some decreases in the final burnouts, the carbon dioxide neutral nature of biomass should be taken into account, and co-combustion is preferable for waste-to-energy-management.

Bio-solubilization of Chinese lignite II: extra-cellular protein analysis

Energy Technology Data Exchange (ETDEWEB)

Tao, Xiu-xiang; Pan, Lan-ying; Shi, Kai-yi; Chen-hui; Yin, Su-dong; Luo, Zhen-fu [China University of Mining & Technology, Xuzhou (China). School of Chemical Engineering and Technology

2009-05-15

A white rot fungus strain, Trichoderma sp. AH, was isolated from rotten wood in Fushun and used to study the mechanism of lignite bio-solubilization. The results showed that nitric acid pretreated Fushun lignite was solubilized by T. sp. AH and that extracellular proteins from T. sp. AH were correlated with the lignite bio-solubilization results. In the presence of Fushun lignite the extracellular protein concentration from T. sp. AH was 4.5 g/L while the concentration was 3 g/L in the absence of Fushun lignite. Sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE) of the extracelular proteins detected at least four new protein bands after the T. sp. AH had solubilized the lignite. Enzyme color reactions showed that extracelular proteins from T. sp. AH mainly consisted of phenol-oxidases, but that lignin decomposition enzymes such as laccase, peroxidase and manganese peroxidases were not present. 9 refs., 8 figs.

Characterization of North American lignite fly ashes. II. XRD Mineralogy

International Nuclear Information System (INIS)

McCarthy, G.J.; Johansen, D.M.; Thedchanamoorthy, A.; Steinwand, S.J.; Swanson, K.D.

1988-01-01

X-ray powder diffraction has been used to determine the crystalline phase mineralogy in samples of fly ash from each of the lignite mining areas of North America. The characteristic phases of North Dakota lignite fly ashes were periclase, lime, merwinite and the sulfate phases anhydrite, thenardite and a sodalite-structure phase. Mullite was absent in these low-Al/sub 2/O/sub 3/ ashes. Montana lignite ash mineralogy had characteristics of ND lignite and MT subbituminous coal fly ashes; mullite and C/sub 3/A were present and the alkali sulfates were absent. Texas and Louisiana lignite fly ashes had the characteristic mineralogy of bituminous coal fly ash: quartz, mullite, ferrite-spinel (magnetite) and minor hematite. Even though their analytical CaO contents were 7-14%, all but one lacked crystalline CaO-containing phases. Lignite fly ashes from Saskatchewan were generally the least crystalline of those studied and had a mineralogy consisting of quartz, mullite, ferrite spinel and periclase. Quantitative XRD data were obtained. The position of the diffuse scattering maximum in the x-ray diffractograms was indicative of the glass composition of the lignite fly ash

Bioprocessing of lignite coals using reductive microorganisms

Energy Technology Data Exchange (ETDEWEB)

Crawford, D.L.

1992-03-29

In order to convert lignite coals into liquid fuels, gases or chemical feedstock, the macromolecular structure of the coal must be broken down into low molecular weight fractions prior to further modification. Our research focused on this aspect of coal bioprocessing. We isolated, characterized and studied the lignite coal-depolymerizing organisms Streptomyces viridosporus T7A, Pseudomonas sp. DLC-62, unidentified bacterial strain DLC-BB2 and Gram-positive Bacillus megaterium strain DLC-21. In this research we showed that these bacteria are able to solubilize and depolymerize lignite coals using a combination of biological mechanisms including the excretion of coal solublizing basic chemical metabolites and extracellular coal depolymerizing enzymes.

Biosolubilization of raw and gamma irradiated lignite by trichoderma asperellum

International Nuclear Information System (INIS)

Sugoro, I.; Astuti, D.I.; Aditiawati, P.; Sasongko, D.

2012-01-01

Biosolubilization is a promising technology for converting solid coal to liquid oil by addition of microorganism. Aim of this research is to compare between gamma irradiated lignite (10 kGy) with raw lignite in biosolubilization by selected fungi Trichoderma asperellum. Treatments were A (MSS + gamma irradiated lignite 5% + T. asperellum) and B (MSS + raw lignite 5% + T. asperellum) with sub-merged culture. There were two parameters observed i.e. biosolubilization product based on absorbance value at λ 250nm and λ 450nm and metal analysis by neutron activation analysis (NAA). The highest biosolubilization will be analyzed by FTIR and GCMS. The results showed that biosolubilization of raw lignite (B) was higher than sterilized lignite (A) based on absorbance value at λ 250nm and λ 450nm . The metal of lignite was decreased after incubation. FTIR analysis showed that both of treatment had similar spectra on biosolubilization products. GCMS analysis showed that both of treatment had different number of hydrocarbon, i.e. C 6 - C 35 (A) and C 10 - C 35 (B) and dominated by aromatic acids, aliphatic and phenylethers. Both of treatment product had the potency as oil substituted but its recommended to deoxygenate for higher quality. (author)

Lignite mining and electricity generation in Poland: The current state and future prospects

International Nuclear Information System (INIS)

Widera, Marek; Kasztelewicz, Zbigniew; Ptak, Miranda

2016-01-01

This opinion paper presents the current state and future scenarios of Polish lignite mining. For many years, over 1/3 of domestic electricity, that is about 53–55 TWh, has been generated by lignite-fired power plants. Currently, with 63–66 million tons of extraction, Poland is the fourth lignite producer worldwide and the second in the European Union. There are three possible scenarios for the development of lignite mining in Poland by 2050. Unfortunately, despite the huge lignite resources, amounting to more than 23.5 billion tons, and great potential of the mining industry, the future of Polish lignite mining does not look optimistic from the economic point of view. This is associated with social and environmental problems, including the European Union's climate and energy policy. However, this may change in the event of a global economic crisis and unstable geopolitical conditions. Therefore, a new energy doctrine for Poland at least by 2050 is urgently needed. - Highlights: •Poland is one of the leaders in lignite production in the European Union. •Energy policy in Poland assumes a key role of lignite in energy mix. •Almost one-third of Polish electricity is currently generated from lignite. •For Polish lignite mining exist pessimistic, realistic and optimistic scenarios. •Extraction of lignite in Poland will gradually decrease in the coming decades.

Utilization of lignite power generation residues for the production of lightweight aggregates.

Science.gov (United States)

Anagnostopoulos, Iason M; Stivanakis, Victor E

2009-04-15

A novel process is proposed for the utilization of lignite combustion solid residues in the production of inflammable lightweight aggregates (LWA). The process consists of two stages, pelletization and sintering, and carbon contained in BA was used as the process fuel. The main residues bottom ash (BA) and fly ash (FA) from Megalopolis power plant were characterized, mixed in different proportions and treated through pelletization and sintering process. Sintering benefits from combustion of BA carbon content and the product is a hardened porous cake. The energy required for achievement of high temperatures, in the range of 1250 degrees C, was offered by carbon combustion and CO(2) evolution is responsible for porous structure formation. Selected physical properties of sintered material relevant to use as lightweight aggregates were determined, including bulk density, porosity and water absorption. Bulk density varies from 0.83 to 0.91 g/cm(3), porosity varies from 60% to 64% and water absorption varies from 66% to 80%. LWA formed is used for the production of lightweight aggregate concrete (LWAC). Thermal conductivity coefficient varies from 0.25 to 0.37 W/mK (lower than maximum limit 0.43 W/mK) and compressive strength varies from 19 to 23 MPa (higher than minimum limit 17 MPa). The results indicate that sintering of lignite combustion residues is an efficient method of utilization of carbon containing BA and production of LWA for structural and insulating purposes. Carbon content of BA is a key factor in LWA production. Finally, this research work comprises the first proposed application for utilization of BA in Greece.

Sustainable lignite mining and utilization. Developments in the Rhenish lignite-mining area; Nachhaltige Braunkohlegewinnung und -nutzung. Entwicklung im Rheinischen Revier

Energy Technology Data Exchange (ETDEWEB)

Gaertner, Dieter [RWE Power AG, Bergheim (Germany). Sparte Tagebaue

2012-09-15

Lignite is an essential module in the Rhenish mining area's economic power. Mini ng in a densely populated region like the Rhineland calls for keeping an eye equ ally on people, the environment and industry now and in the future. By considering all concerns and ensuring transparency in our approach to people, we have succeeded in obtaining public acceptance also for large-scale projects in an environment that is not always easy in Germany. RWE Power plans to use lignite in powe r generation and in upgrading operations for many decades to come, so that the company is systematically implementing the power-plant renewal programme with is planning for BoAplus as highly efficient next-generation lignite-based power plants. Research on CO{sub 2} utilization, flexibilization, energy storage and alternative uses of lignite are as much features of RWE Power's future-proof alignment in the Rhenish mining area as are further innovations in the opencast mines. Core aspects here include further automation in the deployment of main mine equipment, closely dovetailed with innovations in other operating units. Parallel restructuring of the operating units and the Lignite Approvals area are underpinning these measures. Innovations and their translation into technical progress will ensure the success of a measured energy turnaround both in Germany and throughout Europe. However, this requires dependable political conditions, so that an engineering spirit can go on being transformed into entrepreneurial action. (orig.)

Sustainable lignite mining and utilization. Developments in the Rhenish lignite-mining area; Nachhaltige Braunkohlegewinnung und -nutzung. Entwicklung im Rheinischen Revier

Energy Technology Data Exchange (ETDEWEB)

Gaertner, Dieter [RWE Power AG, Bergheim (Germany). Opencast Mines Div.

2012-03-15

Lignite is an essential module in the Rhenish mining area's economic power. Mining in a densely populated region like the Rhineland calls for keeping an eye equally on people, the environment and industry now and in the future. By considering all concerns and ensuring transparency in our approach to people, we have succeeded in obtaining public acceptance also for large-scale projects in an environment that is not always easy in Germany. RWE Power plans to use lignite in power generation and in upgrading operations for many decades to come, so that the company is systematically implementing the power-plant renewal programme with is planning for BoAplus as highly efficient next-generation lignite-based power plants. Research on CO{sub 2} utilization, flexibilization, energy storage and alternative uses of lignite are as much features of RWE Power's future-proof alignment in the Rhenish mining area as are further innovations in the opencast mines. Core aspects here include further automation in the deployment of main mine equipment, closely dovetailed with innovations in other operating units. Parallel restructuring of the operating units and the Lignite Approvals area are underpinning these measures. Innovations and their translation into technical progress will ensure the success of a measured energy turnaround both in Germany and throughout Europe. However, this requires dependable political conditions, so that an engineering spirit can go on being transformed into entrepreneurial action. (orig.)

Microstructure and properties of lignite tar and pitch. Part II

Energy Technology Data Exchange (ETDEWEB)

Walther, H

1954-01-01

Photomicrographs reveal the presence of crystalline wax which affects the working properties in lignite tars and pitch. The crystals are large needles after slow cooling and small after rapid cooling. The crystals are paraffinic in character. All samples were nonhomogeneous. Thus the properties of lignite tar and pitch are varied by the source of the lignite and history of the specimen, neither softening point nor dropping point seems to satisfactorily characterize these tars. The samples exhibit thixotropic behavior characteristic of a structural viscosity and show hysteresis loops on varying the working rate. The variations have hindered use of lignite tars and pitches except where solubility in a solvent such as coal tar oil can be used to advantage.

Production of fuels out of lignite and lignocelluloses; Herstellung von Brennstoffen aus Braunkohle und Lignozellulose

Energy Technology Data Exchange (ETDEWEB)

Naundorf, W.; Schroeder, H.W.; Trommer, D. [TU Bergakademie Freiberg (Germany)

2001-12-01

The acceptance towards solid fuels will increase again if its ease of use is improved, the production costs remain low for extended periods of time, and high thermal efficiencies as well as low pollutant emissions are achieved. These demands can only be met by optimal fuel processing and the use of modern fuel engineering which applies, if possible, continuous and controlled fuel and air feed technology. Two fuels are introduced which are produced out of lignite and lignocelluloses by compaction or by balling granulation. Considering the improvement of combustion properties, remarkable synergy effects occur due to this raw material combination. Lignocelluloses act as an ignition auxillary. Lignite functions as a binding agent, increases the fuels' fire resistance, and guarantees a long, sustained combustion with an excellent combustion rate. (orig.)

Lignite mining in India - thirty years of rich experience

Energy Technology Data Exchange (ETDEWEB)

Tandon, G L

1984-11-01

Exploration of the huge deposits of lignite at Neyveli in Tamil Nadu commenced in 1961 by the opencast method by deploying continuously operating machinery such as bucket-wheel excavators, spreaders and high-speed belt conveyor systems. Adoption of this mining technology to suit the peculiar site conditions at Neyveli has led to many modifications in the equipment and has enriched the experience of the Neyveli Lignite Corporation. This has also made it possible for NLC to formulate schemes for exploration and exploitation of lignite deposits occurring elsewhere in the country.

Lignite mining in India - thirty years of rich experience

Energy Technology Data Exchange (ETDEWEB)

Tandon, G L

1984-11-01

Exploitation of the huge deposits of lignite at Neyveli in Tamil Nadu commenced in 1961 by opencast method by deploying continuously operating machinery such as bucket-wheel excavators, headers and high speed belt conveyor systems. Adoption of this mining technology to suit the peculiar site conditions at Neyveli has led to many modifications in the equipment and has enriched the experience of the Neyveli Lignite Corporation. This has also made it possible for NLC to formulate schemes for exploration and exploitation of lignite deposits occurring elsewhere in the country.

Lignite industry in Greece within a world context: Mining, energy supply and environment

International Nuclear Information System (INIS)

Kavouridis, Konstantinos

2008-01-01

Today coal covers 38% of global production and roughly 30% of the EU-25 power output. In 2005 domestic lignite with a share of 60.5% in power generation and accounting about 30% of primary energy consumption is currently the most important indigenous fuel of Greece. Greece, mining 70 Mt annually, is the second lignite producer in the EU and fourth in the world. Approximately 97% of the lignite used to supply the existing lignite-fired power plants of Greece is mined by Public Power Corporation S.A. (PPC). Lignite as the base load fuel gives a competitive strength in PPC's and Greece's fuel mix. Due to lignite consumer prices in Greece are significantly below those in other comparable markets in EU-15. Extraction of lignite has a very long tradition. Significant achievements and large experience which has been gained during many years of mining operations place Greek lignite-mining industry in the leading position in Europe. The paper presents current state of Greek lignite industry, including operating mines, volume of production and other important production indicators as well as improvements in labor productivity and good results in industrial safety. The future of coal and specifically of Greek lignite will be crucially determined by environmentally compatible, i.e. low-CO 2 generation of electricity. Investment in modernization and renewal of the power plant fleet are the key to securing electricity supply and progress in preventing climate change

Low-temperature carbonization plant for lignite

Energy Technology Data Exchange (ETDEWEB)

Shiotsuki, Y

1949-01-01

The design and operational data of a low-temperature carbonization plant for Japanese lignite are described. The retort had a vertical cylinder with a capacity of about 10 tons per day. By continuous operation, in which a part of the gas produced was circulated and burned in the lignite zone, about 40 percent semicoke and 3 to 4 percent tar were obtained. From the tar the following products were separated: Low-temperature carbonization cresol, 18.3; motor fuel, 1.00; solvent, 9.97; cresol for medical uses, 11.85; and creosote oil, 32 percent.

Lignite chemical conversion in an indirect heat rotary kiln gasifier

Directory of Open Access Journals (Sweden)

Hatzilyberis Kostas S.

2006-01-01

Full Text Available The results on the gasification of Greek lignite using two indirect heat (allothermal pilot rotary kiln gasifiers are reported in the present work. The development of this new reactor-gasifier concept intended for solid fuels chemical conversion exploits data and experience gained from the following two pilot plants. The first unit A (about 100 kg/h raw lignite demonstrated the production of a medium heating value gas (12-13 MJ/Nm3 with quite high DAF (dry ash free coal conversions, in an indirect heat rotary gasifier under mild temperature and pressure conditions. The second unit B is a small pilot size unit (about 10 kg/h raw lignite comprises an electrically heated rotary kiln, is an operation flexible and exhibits effective phase mixing and enhanced heat transfer characteristics. Greek lignite pyrolysis and gasification data were produced from experiments performed with pilot plant B and the results are compared with those of a theoretical model. The model assumes a scheme of three consecutive-partly parallel processes (i. e. drying, pyrolysis, and gasification and predicts DAF lignite conversion and gas composition in relatively good agreement with the pertinent experimental data typical of the rotary kiln gasifier performance. Pilot plant B is currently being employed in lime-enhanced gasification studies aiming at the production of hydrogen enriched synthesis gas. Presented herein are two typical gas compositions obtain from lignite gasification runs in the presence or not of lime. .

Ameliorative properties of lignite fly ash in reclaiming saline and alkali soils

Energy Technology Data Exchange (ETDEWEB)

Mahalingam, P K

1973-08-01

Statistical analysis of the yield of rice grain and straw reveals that there is a significant increase in the yield of grain and straw due to the application of lignite fly ash over controls and application of lignite fly ash either at 5 tons or 10 tons per acre was on par with gypsum application at 5 tons/acre. Maximum yield was recorded in treatment with 5 tons of daincha plus 5 tons of lignite fly ash per acre. This is due to the combined effect of green manure and lignite fly ash. 4 references, 3 tables.

Laboratory experiments and analytical investigations on the transfer of organic substances from lignite into ground water and residue lakes during flooding of opencast lignite mines. Final report; Laborexperimente und analytische Untersuchungen ueber den Eintrag braunkohlebuertiger organischer Stoffe in Grundwaesser und Restseegewaesser bei der Flutung von Braunkohletagebauen. Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Herzschuh, R.; Frauendorf, H.; Herrmann, D.; Pietzsch, K.

2000-05-01

Lignite samples of diffrent lithotypes and composition from opencast mines of Lusatia and the region near Leipzig were submitted to weathering processes in laboratory scale experiments and the transfer of organic matter from lignite into the hydrosphere has been observed. By means of high-performance liquid chromatography/electrospray mass spectrometry used in combination with data from gas chromatography/mass spectrometry numerous lignite-derived aromatic and heteroaromatic (poly-)carboxylic acids as well as aliphatic dicarboxylic acids could be characterized in the aqueous extracts. Investigations on water samples from lignite mining residue lakes cofirm these results. Furthermore, formation of chlororganic compounds like polychlorinated dibenzo-p-dioxine and furans (PCDD/F) and polychlorinated biphenyls (PCB), benzenes (PCBz) and phenols (PCPh) has been investigated on different lignite samples under natural weathering conditions and thermal treatment. (orig.) [German] Braunkohlen verschiedener Lithotypen und Zusammensetzung aus Tagebauen der Lausitz und der Region um Leipzig wurden in Laborexperimenten Verwitterungsprozessen unterzogen und der Uebergang organischer Materie aus der Braunkohle in die Hydrosphaere beobachtet. Mit Hilfe der HPLC-Elektrospray-MS-Untersuchungen in Kombination mit Daten aus GC-MS-Messungen konnten zahlreiche aus der Braunkohle stammende aromatische und heteroaromatische (Poly-)Carbonsaeuren sowie aliphatische Dicarbonsaeuren in den waessrigen Extrakten charakterisiert werden. Untersuchungen an Wasserproben aus bereits gefluteten Tagebaurestseen bestaetigen diese Ergebnisse. Weiterhin wurde die Bildung chlororganischer Verbindungen, wie polychlorierter Dibenzo-p-dioxine und -furane (PCDD/F) sowie polychlorierter Biphenyle (PCB), Benzole (PCBz) und Phenole (PCPh) an unterschiedlichen Braunkohleproben unter natuerlichen Bedingungen und nach thermsicher Behandlung untersucht. (orig.)

A realistic EU vision of a lignite-based energy system in transition: Case study of Serbia

Directory of Open Access Journals (Sweden)

Batas-Bjelić Ilija

2015-01-01

Full Text Available Several Contracting Parties to the Treaty establishing the Energy Community of the South East Europe, currently in energy transition, have electricity production dominantly based on lignite which contrasts their new reality. Planning approach to designing a new feasible energy policy is presented in this paper. This novel approach in using EnergyPLAN tool stems from analysis of market operation of lignite thermal power plants on hourly basis, and quantification of the feasibility of the energy policy and its alignment with EU vision, and is presented in few scenarios. It was found out that the Serbian energy system is highly sensitive to the electricity market and CO2 tax increase, because the marginal costs for lignite generation will increase to more than 50€/MWh. Shifting in the merit order will be observed even at lower CO2 tax levels, because of the intensity of the emission of the electricity sector (calculated to be higher than 700gCO2/kWhel, according to current energy policy. Based on the increased use of renewable energy sources and more efficient energy conversion technologies, socio-economic and energy policy feasibility would be increased, while long-term marginal costs would be improved by 2€/MWh and emission intensity by 258 gCO2/kWhel, compared to the current energy policy. These contributions, shown in the Serbian case, are of general importance for other lignite dominated Contracting Parties to Treaty establishing the Energy Community. [Projekat Ministartsva nauke Republike Srbije, br. 42009

Transformation of heavy metals in lignite during supercritical water gasification

International Nuclear Information System (INIS)

Chen, Guifang; Yang, Xinfei; Chen, Shouyan; Dong, Yong; Cui, Lin; Zhang, Yong; Wang, Peng; Zhao, Xiqiang; Ma, Chunyuan

2017-01-01

Highlights: • The transformations of heavy metals during lignite SCWG were investigated. • The risks of heavy metals in lignite and residues after SCWG were evaluated. • The effects of experimental conditions on corrosion during SCWG were studied. - Abstract: Transformation characteristics of heavy metals during lignite supercritical water gasification (SCWG) were studied. A sequential extraction procedure (modified Tessier method) was used to selectively extract different fractions of Pb, Cd, Cr, Mn, Cu, Ni, and Zn. Heavy metals transformed into more stable fractions after SCWG. For Pb, Cd, Mn, Cu, and Zn, SCWG reduced the bioavailability and the risks posed by heavy metals in lignite. Under the experimental conditions, the conversion rates for Pb and Cd were 16.0%–25.2% and 16.3%–23.4%, respectively, whereas those for Mn, Cu, and Zn were much lower. Solid products enriched with Pb, Cd, Mn, Cu, and Zn were obtained after SCWG; the contents of these metals varied slightly in the liquid products under different experimental conditions. Excess Cr and Ni that did not originate from lignite were found in the residues, owing to reactor corrosion during lignite SCWG. Higher temperatures alleviated corrosion, whereas higher pressures and equivalence ratios (ER) had the opposite effect. None of the heavy metals were detected in the gas phase under the experimental conditions used in the present study. The correlation between the distributions of heavy metals and the experimental conditions were also studied. The transformation pathways of Pb, Cd, Mn, Cu, and Zn during SCWG were deduced according to the experimental results.

Combustion of uraniferous lignites in fluidized bed

International Nuclear Information System (INIS)

Morales, G.; Gasos, P.

1985-01-01

In this paper a description of the continuous fluid bed combustion pilot plant unit, installed in the Junta de Energia Nuclear facilities, is presented. Besides, this paper deals with some of the studies carried out in the pilot plant aimed at the recovery of uranium from lignites, high in sulfur and ashes, coming from Calaf basin (Barcelona). These studies include the recovery of the heating value of these lignites and the reduction of environmental effect of SO 2 . Based on these studies an application exercise is presented. 9 references, 5 figures, 5 tables

Perspectives of the German lignite industry 2014; Perspektiven der deutschen Braunkohlenindustrie 2014

Energy Technology Data Exchange (ETDEWEB)

Hartung, Matthias; Milojcic, George [DEBRIV, Koeln (Germany)

2014-11-01

The decision to phase out nuclear energy and gradually realign the electricity system towards more renewables in the future required some extensive changes to electricity generation transmission. One of the issues to be considered is what role lignite can play in the transformation of the electricity system and what application is offered to Germany and its regions. However, lignite has some stable factors and their development is fairly predictable. Domestic lignite is one such example. Beyond its familiar attributes, 'secure, competitive and economically important for the regions', 'flexibility' is a key word that indicates a new dimension for the German lignite industry.

Foreseen development of mining of lignite; Przewidywany rozwoj gornictwa wegla brunatnego

Energy Technology Data Exchange (ETDEWEB)

Kozlowski, Z. [Wroclaw University of Technology, Wroclaw (Poland). Dept. of Geo-engineering, Mining and Geology

2004-07-01

The future of activity in Poland's lignite sector will be determined by the demand for this fuel, which will in turn result from mining possibilities and economic competitiveness of the fuel in relation to other sources of electrical energy. The paper discusses all these factors and presents a framework programme for the development of Poland's lignite sector until 2040 (in detail) and further ahead to 2075, called the 'Agreement of manufacturers of lignite'. 4 refs., 5 tabs.

JV Task 98 - Controlling Mercury Emissions for Utilities Firing Lignites from North America

Energy Technology Data Exchange (ETDEWEB)

Steven Benson

2007-06-15

This project compiled and summarized the findings and conclusions of research, development, and demonstration projects on controlling mercury from lignite coals. A significant amount of work has been conducted since 1994 on mercury in lignite, mercury measurement in flue gases, sorbent, sorbent enhancement additives, oxidation agent development, and full-scale demonstration of mercury control technologies. This report is focused on providing the lignite industry with an understanding of mercury issues associated with the combustion of lignite, as well as providing vital information on the methods to control mercury emissions in coal-fired power plants.

Characteristics of Mae Moh lignite: Hardgrove grindability index and approximate work index

Directory of Open Access Journals (Sweden)

Wutthiphong Tara

2012-02-01

Full Text Available The purpose of this research was to preliminarily study the Mae Moh lignite grindability tests emphasizing onHardgrove grindability and approximate work index determination respectively. Firstly, the lignite samples were collected,prepared and analyzed for calorific value, total sulfur content, and proximate analysis. After that the Hardgrove grindabilitytest using ball-race test mill was performed. Knowing the Hardgrove indices, the Bond work indices of some samples wereestimated using the Aplan’s formula. The approximate work indices were determined by running a batch dry-grinding testusing a laboratory ball mill. Finally, the work indices obtained from both methods were compared. It was found that allsamples could be ranked as lignite B, using the heating value as criteria, if the content of mineral matter is neglected. Similarly,all samples can be classified as lignite with the Hargrove grindability indices ranging from about 40 to 50. However, there isa significant difference in the work indices derived from Hardgrove and simplified Bond grindability tests. This may be due todifference in variability of lignite properties and the test procedures. To obtain more accurate values of the lignite workindex, the time-consuming Bond procedure should be performed with a number of corrections for different milling conditions.With Hardgrove grindability indices and the work indices calculated from Aplan’s formula, capacity of the roller-racepulverizer and grindability of the Mae Moh lignite should be investigated in detail further.

Eocene Yegua Formation (Claiborne group) and Jackson group lignite deposits of Texas

Science.gov (United States)

Hook, Robert W.; Warwick, Peter D.; Swanson, Sharon M.; Hackley, Paul C.; Warwick, Peter D.; Karlsen, Alexander K.; Merrill, Matthew D.; Valentine, Brett J.

2011-01-01

The lignite deposits within the upper Eocene Yegua Formation (Claiborne Group) and the overlying Jackson Group are among the coal resources that were not quantitatively assessed as part of the U.S. Geological Survey's (USGS) National Coal Resource Assessment (NCRA) program in the Gulf Coastal Plain coal province. In the past, these lignite-bearing stratigraphic units often have been evaluated together because of their geographic and stratigraphic proximity (Fisher, 1963; Kaiser, 1974; Kaiser et al., 1980; Jackson and Garner, 1982; Kaiser, 1996) (Figures 1, 2). The term “Yegua-Jackson trend“ is used informally herein for the lignite-bearing outcrops of these Late Eocene deposits in Texas. Lignite beds in the Yegua-Jackson trend generally are higher both in ash yield and sulfur content than those of the underlying Wilcox Group (Figure 2). Recent studies (Senkayi et al., 1987; Ruppert et al., 1994; Warwick et al., 1996, 1997) have shown that some lignite beds within the Yegua-Jackson trend contain partings of volcanic ash and host elevated levels of trace elements that have been identified as potentially hazardous air pollutants (HAPs) in the United States Clean Air Amendments of 1990. Lignite beds within the Yegua Formation are thin (less than or equal to 6 ft) and laterally discontinuous in comparison with most Wilcox Group deposits (Ayers, 1989a); in contrast, the Jackson Group lignite beds range up to 12 ft in total thickness and are relatively continuous laterally, extending nearly 32 mi along strike.

Expansion of Neyveli lignite mines

Energy Technology Data Exchange (ETDEWEB)

Kasturi, T S

1982-06-01

This paper describes activities at Neyveli lignite mines in the Tamil Nadu region of India. The equipment used, in mining and materials handling is described. Problems encountered in the conveyor transport system are described, and the solutions finally adopted are presented.

Use of INAA for investigation of emission of elements in combustion of Polish lignite

International Nuclear Information System (INIS)

Janczyszyn, J.; Loska, L.; Pohorecki, W.; Wagner, M.

2002-01-01

Instrumental neutron activation analysis (INAA) has been applied for the determination of trace elements content in samples of Polish lignite and its ash. Pairs of results, for lignite and ash, and respective ash contents were used for calculation of the percentage of element remaining in ash after the lignite combustion. (author)

Effects of lignite application on ammonia and nitrous oxide emissions from cattle pens

Energy Technology Data Exchange (ETDEWEB)

Sun, Jianlei, E-mail: su@unimelb.edu.au [Faculty of Veterinary and Agricultural Sciences, The University of Melbourne, VIC 3010 (Australia); Bai, Mei [Faculty of Veterinary and Agricultural Sciences, The University of Melbourne, VIC 3010 (Australia); Shen, Jianlin [Institute of Subtropical Agriculture, Chinese Academy of Sciences, Changsha 410125 (China); Griffith, David W.T. [Department of Chemistry, University of Wollongong, NSW 2522 (Australia); Denmead, Owen T. [Faculty of Veterinary and Agricultural Sciences, The University of Melbourne, VIC 3010 (Australia); Hill, Julian [Ternes Agricultural Consulting Pty Ltd, Upwey, VIC 3158 (Australia); Lam, Shu Kee; Mosier, Arvin R. [Faculty of Veterinary and Agricultural Sciences, The University of Melbourne, VIC 3010 (Australia); Chen, Deli, E-mail: delichen@unimelb.edu.au [Faculty of Veterinary and Agricultural Sciences, The University of Melbourne, VIC 3010 (Australia)

2016-09-15

Beef cattle feedlots are a major source of ammonia (NH{sub 3}) emissions from livestock industries. We investigated the effects of lignite surface applications on NH{sub 3} and nitrous oxide (N{sub 2}O) emissions from beef cattle feedlot pens. Two rates of lignite, 3 and 6 kg m{sup −2}, were tested in the treatment pen. No lignite was applied in the control pen. Twenty-four Black Angus steers were fed identical commercial rations in each pen. We measured NH{sub 3} and N{sub 2}O concentrations continuously from 4th Sep to 13th Nov 2014 using Quantum Cascade Laser (QCL) NH{sub 3} analysers and a closed-path Fourier Transform Infrared Spectroscopy analyser (CP-FTIR) in conjunction with the integrated horizontal flux method to calculate NH{sub 3} and N{sub 2}O fluxes. During the feeding period, 16 and 26% of the excreted nitrogen (N) (240 g N head{sup −1} day{sup −1}) was lost via NH{sub 3} volatilization from the control pen, while lignite application decreased NH{sub 3} volatilization to 12 and 18% of the excreted N, for Phase 1 and Phase 2, respectively. Compared to the control pen, lignite application decreased NH{sub 3} emissions by approximately 30%. Nitrous oxide emissions from the cattle pens were small, 0.10 and 0.14 g N{sub 2}O-N head{sup −1} day{sup −1} (< 0.1% of excreted N) for the control pen, for Phase 1 and Phase 2, respectively. Lignite application increased direct N{sub 2}O emissions by 40 and 57%, to 0.14 and 0.22 g N{sub 2}O-N head{sup −1} day{sup −1}, for Phase 1 and Phase 2, respectively. The increase in N{sub 2}O emissions resulting from lignite application was counteracted by the lower indirect N{sub 2}O emission due to decreased NH{sub 3} volatilization. Using 1% as a default emission factor of deposited NH{sub 3} for indirect N{sub 2}O emissions, the application of lignite decreased total N{sub 2}O emissions. - Graphical abstract: Lignite application substantially decreased NH{sub 3} emissions from cattle feedlots and increased

Organic petrographical, mineralogical and geochemical features of the Achlada and Mavropigi lignite deposits, NW Macedonia, Greece

Energy Technology Data Exchange (ETDEWEB)

Koukouzas, Nikolaos [Centre for Research and Technology Hellas, Institute for Solid Fuels Technology and Applications, Mesogeion Ave. 357-359, GR-15231 Halandri, Athens (Greece); Kalaitzidis, Stavros P. [Geological Services, BHP Billiton Mitsubishi Alliance, Central Queensland Office, Peak Downs Mine, Moranbah, QLD 4744 (Australia); Ward, Colin R. [School of Biological, Earth and Environmental Sciences, University of New South Wales, Sydney, NSW 2052 (Australia)

2010-09-01

The Achlada and Mavropigi lignite deposits in northern Greece provide the main coal source for the next generation of Greek power plants. A comparative characterization of these two lignite deposits is presented, covering the coal rank and the features of the maceral components, based on detailed coal petrography, and the mineralogical and geochemical features of the coals and their ashes, based on XRF and XRD analyses. The data are used to interpret the palaeoenvironments of the lignite beds, as well as factors that may affect their burnout behavior. Both deposits have a lignite C rank. The Mavropigi lignite is mainly a matrix lignite lithotype, whereas the Achlada deposit consists both of matrix and xylite-rich lithotypes. The Achlada lignite was formed in a fluviatile environment, mainly in the abandoned channels of a meandering river system during flooding periods; hence it is enriched in inorganic matter, with ash values > 30 wt.%. The Mavropigi lignite formed in a reed-marsh environment under limno-telmatic conditions, and displays ash values < 30 wt.%. The inorganic matter of the two deposits is different in composition due to the contrasting environments, and these differences should be taken into account in optimizing their utilization for power production. A preliminary assessment indicates that the Achlada lignite may have more favorable slagging and fouling properties than the Mavropigi lignite, although experimental studies are required for more solid conclusions to be reached. (author)

The effect of lignite quality variation on the efficiency of on-line ash analyzers

Energy Technology Data Exchange (ETDEWEB)

Galetakis, Michael J. [Technical University of Crete, Dept. of Mineral Resources Engineering, University Campus, 73 100 Hania (Greece); Pavloudakis, Francis F. [Public Power Corporation SA, General Division of Mines, Kifisou and Dyrrahiou 89, 104 43 Athens (Greece)

2009-12-01

A sustainable coal industry needs to achieve a number of objectives including improvements in utilization of deposits, energy efficiency, and environmental performance during combustion. The ''Clean Coal Concept'' promises to combine the secure and low cost electricity supply offered by hard coal and lignite with adequate environmental precautions. In this context, modern quality control systems, which are greatly based on the on-line analyzers, play an important role in achieving sustainability targets. This paper examines the possibility of using commercial on-line analysis systems for monitoring the mineral matter content of low quality lignite mined from the lignite basin of Megalopolis, Peloponnese, Greece. The effect of the accuracy of the on-line analyzers to process control, when used for the characterization of low rank coals with complex and variable composition, is investigated by carrying out numerous bench- and pilot-scale trials. Pilot-scale trials were based on a dual energy gamma-ray transmission analyzer, which was installed on the conveyor belt that transports lignite from the mine pit to the homogenization stockyard. All measurement data were compared to data gathered during the realisation of similar trials in the lignite mines of Ptolemais Basin, Northern Greece. Results indicated that the accuracy of the on-line measurements was not satisfactory and did not allow lignite quality monitoring in real time. The achieved inferior accuracy of the on-line measurement's accuracy, compared to previous applications at other mining sites, was related to the intense variation of the mineral matter content of lignite and lignite composition, which distorted the calibration of the analyzer. The latter is based on certain assumptions regarding the average mass absorption coefficient of the organic and mineral matter contained in the lignite. Further experimental work is needed to investigate solutions for successful implementation of

Surface properties of thermally treated composite wood panels

Science.gov (United States)

Croitoru, Catalin; Spirchez, Cosmin; Lunguleasa, Aurel; Cristea, Daniel; Roata, Ionut Claudiu; Pop, Mihai Alin; Bedo, Tibor; Stanciu, Elena Manuela; Pascu, Alexandru

2018-04-01

Composite finger-jointed spruce and oak wood panels have been thermally treated under standard pressure and oxygen content conditions at two different temperatures, 180 °C and respectively 200 °C for short time periods (3 and 5 h). Due to the thermally-aided chemical restructuration of the wood components, a decrease in water uptake and volumetric swelling values with up to 45% for spruce and 35% for oak have been registered, comparing to the reference samples. In relation to water resistance, a 15% increase of the dispersive component of the surface energy has been registered for the thermal-treated spruce panels, which impedes water spreading on the surface. The thermal-treated wood presents superior resistance to accelerated UV exposure and subsequently, with up to 10% higher Brinell hardness values than reference wood. The proposed thermal treatment improves the durability of the finger-jointed wood through a more economically and environmental friendly method than traditional impregnation, with minimal degradative impact on the structural components of wood.

Petrological, geochemical and isotopic characteristics of lignite and calcified lignite from mining area Pesje, Velenje Basin, Slovenia

Science.gov (United States)

Vrabec, Mirijam; Markič, Miloš; Vrabec, Marko; Jaćimović, Radojko; Kanduč, Tjaša

2014-05-01

Lignite (organic rich) and calcified lignite (inorganic rich) samples from excavation field -50c mining area Pesje, Velenje Basin, Slovenia were investigated. During geological and structural mapping lignite and calcified lignite samples were systematically taken for determination of their petrological, geochemical and isotopic characteristics. Lignite is composed of fine detritical gelified matrix. At least five different types of calcified lignite were recognized forming laminations, calcifications after wood, petrified wood and complete replacements of lignite with carbonate. All measured parameters so far indicate geochemical processes during sedimentation of the Velenej Basin. After macroscopic description samples were split to organic and inorganic component (Ward, 1984) and powdered in an agate mortar for geochemical and isotopic analyses. Major and trace elements (As, B, Ba, Cd, Co, Cr, Cu, Hg, Mn, Mo, Sb, Se, Th, U, Zn) in these samples were determined by instrumental neutron activation analysis (INAA) using k-0 standardization method (Jaćimović et al, 2002). The isotopic composition of carbon and nitrogen was determined using a Europa 20-20 continuous flow IRMS ANCA-SL preparation module. A 1 mg amount of a sample was weighed in a tin capsule for carbon and 10 mg for nitrogen analysis. Samples for carbon analyses were pretreated with 1 M HCl to remove carbonates. Carbonate samples from carbonate-rich strata and calcified xylite were first roasted at 450 deg C (Krantz et al., 1987). Three miligrams of carbonate sample was transformed into CO2 by reaction with anhydrous H3PO4 at 55 deg C under vacuum (McCrea, 1950) and measured with GV 2003 isotope ratio mass spectrometer. Measured isotopic composition of oxygen as VPDB values was recalculated to the VSMOW reference standard to enable the comparison with data from other coal basins. SEM/EDXS of carbonate rich sediments was performed with JEOL JSM 5800 electron microanalyzer scanning electron microscope

Germany's lignite industry in 2011; Die deutsche Braunkohlenindustrie im Jahr 2011

Energy Technology Data Exchange (ETDEWEB)

Maassen, Uwe [Bundesverband Braunkohle, Koeln (Germany); Statistik der Kohlenwirtschaft e.V., Koeln (Germany); Schiffer, Hans-Wilhelm [RWE Aktiengesellschaft, Essen (Germany)

2012-05-15

From 2010 to 2011, Germany's domestic lignite output edged up 4.2% from 169.4 mill. t to 176.5 mill. t. This output is equivalent to a net calorific value of 54.4 mill. tce; of the total output, 157.4 mill. t, or some 90% was used in utility power plants for public supply. That was 3.6% more than in the previous year; 15.5 mill. t was input in the factories of the lignite-mining industry to make solid products, while 2.6 mill. t was used to generate electricity in mine-mouth power plants. Other sales of raw lignite and changes in stocks accounted for 1.0 mill. t. Lignite made a 24.9% contribution toward Germany's total power generation in 2011. In 2011, lignite had an 11.7% share in primary-energy consumption, giving it slot four in Germany's energy-consumption balance after mineral oil (34.0%), natural gas (20.4%) and hard coal (12.6%). Renewable resources cover 10.9, while nuclear energy accounts for 8.8% and other energy sources for 1.6%. With output of 54.4 mill. tce, lignite held a share of 38,5% in Germany's primary-energy production of some 141.3 mill. tce. The contributions made by the other energy carriers to primary-energy production in 2011 were as follows: 12.3 mill. tce hard coal, 13.1 mill. tce gas, 3.9 mill tce mineral oil, 49.5 mill. tce renewables, and 8.1 mill. tce other energy sources. Of the total electricity that Germany produced in 2011, 24,9% was accounted for by lignite. This means that lignite led the ranking of the most important input energies for electricity generation in 2011, followed by renewables with 19.9% hard coal with 18.6%, nuclear energy with 17.6% and gas with 13.7%. Other energy sources made a 5.3% contribution to total gross power generation. The most important ratios for the contributions made by the various lignite-mining areas to Germany's energy supply was shown. CO{sub 2} emissions from lignite rose 3.7% from 168.7 mill. t in 2010 to 175 mill. t in 2011. In the entire period from 1990 to 2011, a

Germany's lignite industry in 2012; Die deutsche Braunkohlenindustrie im Jahr 2012

Energy Technology Data Exchange (ETDEWEB)

Maassen, Uwe [Bundesverband Braunkohle, Statistik der Kohlenwirtschaft e.V., Koeln (Germany); Schiffer, Hans-Wilhelm [RWE Aktiengesellschaft, Essen (Germany). CEA-W Allgemeine Wirtschaftspolitik/Wissenschaft

2013-05-15

From 2011 to 2012, Germany's domestic lignite output edged up to 5.1% from 176.5 mill. t to 185.4 mill. t. This figure is equivalent to a net calorific value of 57.2 mill. tce. Of the total output, 166.3 mill. t, or some 90%, was used in utility power plants for the public supply, i.e. 5.7% more than in the previous year. In addition, 15.1 mill. t was input in the factories of the lignite-mining industry to make solid products, while 3.0 mill. t was used to generate electricity in mine-mouth power plants. Other sales of raw lignite and changes in stocks accounted for 1.0 mill. t. Lignite made a 25.7% contribution toward Germany's total power generation in 2012. In 2012, lignite had a 12.1% share in primary-energy consumption balance after mineral oil (33.1%), natural gas (21.6%) and hard coal (12.2%). Renewable resources cover 11.6%, while nuclear energy accounts for 8.0% and other energy sources for 1.4%. With output of 57.2 mill. tce, lignite held a share of 38.4% in Germany's primary-energy production of some 149 mill. tce in 2012. The contributions made by other energy carriers to primary-energy production in 2012 were as follows: 11.1 mill. tce hard coal, 13.3 mill. tce gas, 3.8 mill. tce mineral oil, 54.0 mill. tce renewables, and 9.5 mill. tce other energy sources. Of the total electricity amount that Germany produced in 2012, 25.7% was accounted for by lignite. This means that lignite led the ranking of the most important input energies for electricity generation in 2012, followed by renewables with 22.1%, hard coal with 19.1%, nuclear energy with 16.1% and gas with 11.3%. Other energy sources made a 5.7% contribution to total gross power generation. The most important ratios for the contributions made by the various lignite-mining areas to Germany's energy supply are shown. CO{sub 2} emissions from lignite rose 5.1% from 173.9 mill. t in 2011 to 182.8 mill. t in 2012. In the total period from 1990 to 2012, a decline of 159.4 mill. t, or

Powerful boost for Indian lignite

Energy Technology Data Exchange (ETDEWEB)

1985-06-01

The Neyveli Lignite Corporation (NLC) of India has begun the first phase of an expansion program that will open a second mine and boost lignite production in Tamil Nadu to nearly five times its present level within the next 15 years. Mining conditions at Neyveli are particularly difficult. The harsh abrasive overburden strata present severe and strenuous conditions; sticky and marshy surface clays, the presence of groundwater aquifers, the cyclonic and monsoonal climate and high stripping ratios are other problems. The overburden is drilled and blasted; in areas of sticky topsoil, non-stick liners for the buckets etc. are used. Adequate safeguards and infrastructure are being developed to deal with differing strata conditions. The conveyor transport system features slow, wider belt conveyors, changeover from fixed type roller to freely hanging garland type, interlinking of benches and specially designed drive heads. The groundwater aquifers are continuously depressurized by grid pumping from a series of pumps; boreholes have been sunk to 120 m.

Sulfomethylated lignite salt as a sacrifical agent in oil recovery processes

Energy Technology Data Exchange (ETDEWEB)

Kudchadker, M.V.; Weiss, W.J.

1978-02-07

A process is described for recovering petroleum from oil reservoirs by secondary recovery methods. The process involves injecting via an injection well into the reservoir an aqueous solution of sulfomethylated lignite salt as a sacrificial agent to inhibit the deposition of surfactant and polymer on the reservoir matrix. The process is conducted by first injecting the lignite salt into the formation through the injection well and following it with either a polymer or a surfactant solution, which also may contain the lignite salt. The polymer or surfactant would then be followed by a drive fluid, such as water, to push the chemicals and oil to the production well. (18 claims)

Natural desulfurization in coal-fired units using Greek lignite.

Science.gov (United States)

Konidaris, Dimitrios N

2010-10-01

This paper analyzes the natural desulfurization process taking place in coal-fired units using Greek lignite. The dry scrubbing capability of Greek lignite appears to be extremely high under special conditions, which can make it possible for the units to operate within the legislative limits of sulfur dioxide (SO2) emissions. According to this study on several lignite-fired power stations in northern Greece, it was found that sulfur oxide emissions depend on coal rank, sulfur content, and calorific value. On the other hand, SO2 emission is inversely proportional to the parameter gammaCO2(max), which is equal to the maximum carbon dioxide (CO2) content by volume of dry flue gas under stoichiometric combustion. The desulfurization efficiency is positively correlated to the molar ratio of decomposed calcium carbonate to sulfur and negatively correlated to the free calcium oxide content of fly ash.

Ash content of lignites - radiometric analysis

International Nuclear Information System (INIS)

Leonhardt, J.; Thuemmel, H.W.

1986-01-01

The quality of lignites is governed by the ash content varying in dependence upon the geologic conditions. Setup and function of the radiometric devices being used for ash content analysis in the GDR are briefly described

The lignite industry and regional development. Interactions exemplified by the Rhenish mining area

International Nuclear Information System (INIS)

Kulik, Lars; Voigt, Jens

2013-01-01

Even in times of globalised markets, the German lignite industry retains its local and regional roots. Viewed against this background, the relationship between lignite industry and regional actors, and the interactions between the two play a major role in the perspectives for this branch of Germany's energy sector. Today, the links between the lignite industry and regional bodies are those of a partnership at eye-level. This type of relationship between the industry and regional actors has led to new forms and methods of cooperation at various levels. This is particularly evident in the efforts to re-shape the regional structure, develop the structure of townships and strengthen the economic structure with lignite playing an important role and new partners which are gaining in importance. (orig.)

Validation of a FBC model for co-firing of hazelnut shell with lignite against experimental data

Energy Technology Data Exchange (ETDEWEB)

Kulah, Gorkem [Middle East Technical University, Department of Chemical Engineering, 06531 Ankara (Turkey)

2010-07-15

Performance of a comprehensive system model extended for modelling of co-firing of lignite and biomass was assessed by applying it to METU 0.3 MW{sub t} Atmospheric Bubbling Fluidized Bed Combustor co-firing lignite with hazelnut shell and validating its predictions against on-line temperature and concentration measurements of O{sub 2}, CO{sub 2}, CO, SO{sub 2} and NO along the same test rig fired with lignite only, lignite with limestone addition and lignite with biomass and limestone addition. The system model accounts for hydrodynamics; volatiles release and combustion, char combustion, particle size distribution for lignite and biomass; entrainment; elutriation; sulfur retention and NO formation and reduction, and is based on conservation equations for energy and chemical species. Special attention was paid to different devolatilization characteristics of lignite and biomass. A volatiles release model based on a particle movement model and a devolatilization kinetic model were incorporated into the system model separately for both fuels. Kinetic parameters for devolatilization were determined via thermogravimetric analysis. Predicted and measured temperatures and concentrations of gaseous species along the combustor were found to be in good agreement. Introduction of biomass to lignite was found to decrease SO{sub 2} emissions but did not affect NO emissions significantly. The system model proposed in this study proves to be a useful tool in qualitatively and quantitatively simulating the processes taking place in a bubbling fluidized bed combustor burning lignite with biomass. (author)

Cheap carbon sorbents produced from lignite by catalytic pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Kuznetsov, B.N.; Schchipko, M.L. [Inst. of Chemistry of Natural Organic Materials, Akademgorodok, Krasnoyarsk (Russian Federation)

1995-12-01

Some data are presented describing the new technology of carbon sorbent production from powdered lignite in the installation with fluidized bed of catalyst. It was shown the different types of char products with extended pore structure and high sorption ability can be produced from cheap and accessible lignite of Kansk-Achinsk coal pit in pilot installation with fluidized bed of Al-Cu-Cr oxide catalyst or catalytically active slag materials. In comparison with the conventional technologies of pyrolysis the catalytic pyrolysis allows to increase by 3-5 times the process productivity and to decrease significantly the formation of harmful compounds. The latter is accomplished by complete oxidation of gaseous pyrolysis products in the presence of catalysts and by avoiding the formation of pyrolysis tars - the source of cancerogenic compounds. The technology of cheap powdered sorbent production from lignites makes possible to obtain from lignite during the time of pyrolysis only a few seconds char products with porosity up to 0.6 cm{sup 3} /g, and specific surface area more than 400 m{sup 3} /g. Some methods of powdered chars molding into carbon materials with the different shape were proved for producing of firmness sorbents. Cheap carbon sorbents obtained by thermocatalytic pyrolysis can be successfully used in purification of different industrial pollutants as one-time sorbent or as adsorbents of long-term application with periodic regeneration.

Changes of chemical properties of humic acids from crude and fungal transformed lignite

Energy Technology Data Exchange (ETDEWEB)

LianHua Dong; Quan Yuan; HongLi Yuan [China Agricultural University, Beijing (China). College of Biological Science

2006-12-15

The development of biological processes for fossil energy utilization has received increasing attention in recent years. There are abundance of lignite resources in China and the lignite, a low-grade coal, can be transformed by a Penicillium sp. After fungal transformation, the contents of humic acid and water-soluble humic material increased from 38.6% to 55.1%, and from less than 4.0% to 28.2%, respectively. The differences in chemical properties of crude lignite humic acid (aHA), fungal transformed lignite humic acid (bHA) and water-soluble humic material from fungal transformed lignite (WS) were studied. Elemental analysis and size exclusion chromatography showed that the N content of bHA increased by 47.36% compared with aHA, and the molecular mass of bHA was smaller than aHA. And the WS with the smallest molecular mass contained most content of N. The {sup 13}C NMR and FT-IR spectra of aHA and bHA showed that aHA contained more aromatic structure than bHA. 44 refs., 3 figs., 2 tabs.

Distribution and correlation of the natural radionuclides in a coal mine of the West Macedonia Lignite Center (Greece).

Science.gov (United States)

Tsikritzis, L I; Fotakis, M; Tzimkas, N; Kolovos, N; Tsikritzi, R

2008-02-01

The distribution and correlation of six natural nuclides in the West Macedonia Lignite Center, Northern Greece were studied. Fifty-five samples of lignite, aged from 1.8 to 5 million years, and corresponding steriles, beds of marls, clays and sands alternating with the lignite, were collected perpendicular to the mine benches and measured spectroscopically. The mean concentrations of (238)U and (226)Ra in lignites were found to be higher than that in steriles since these nuclides are associated with the organic material of lignite, whereas (238)U/(226)Ra equilibrium was not observed in either lignites or steriles. Finally, the ratio (226)Ra/(228)Ra in lignites was approximately double of that in steriles, confirming the affinity of the (238)U series with the coal matrix in contrast to the (232)Th series. No correlation was found between radionuclide concentrations and the depth of the sample, nor with the ash content of lignite.

Energy and water conservation at lignite-fired power plants using drying and water recovery technologies

International Nuclear Information System (INIS)

Liu, Ming; Qin, Yuanzhi; Yan, Hui; Han, Xiaoqu; Chong, Daotong

2015-01-01

Highlights: • Pre-drying and water recovery technologies were used to conserve energy and water. • The energy and water conservation potential were analyzed with reference cases. • The air-cooling unit produces water when the water content of lignite is high enough. • Influences of main parameters on energy and water conservation were analyzed. - Abstract: Lignite is considered as a competitive energy raw material with high security of supply viewed from a global angle. However, lignite-fired power plants have many shortcomings, including high investment, low energy efficiency and high water use. To address these issues, the drying and water recovery technologies are integrated within lignite-fired power plants. Both air-cooling and wet-cooling units with three kinds of lignite as feeding fuel were analyzed quantitatively. Results showed that energy conservation and water conservation are obtained simultaneously. The power plant firing high moisture lignite becomes more environmental friendly with higher power generation efficiency and a lower water makeup rate than the one firing low moisture lignite. And further calculation revealed that the air-cooling unit needs no makeup water and even produces some water as it generates power, when the water carrying coefficient is higher than 40 g/MJ.

Naturally occurring radioactive materials (NORMs) generated from lignite-fired power plants in Kosovo.

Science.gov (United States)

Hasani, F; Shala, F; Xhixha, G; Xhixha, M K; Hodolli, G; Kadiri, S; Bylyku, E; Cfarku, F

2014-12-01

The energy production in Kosovo depends primarily on lignite-fired power plants. During coal combustion, huge amounts of fly ash and bottom ash are generated, which may result in enriched natural radionuclides; therefore, these radionuclides need to be investigated to identify the possible processes that may lead to the radiological exposure of workers and the local population. Lignite samples and NORMs of fly ash and bottom ash generated in lignite-fired power plants in Kosovo are analyzed using a gamma-ray spectrometry method for the activity concentration of natural radionuclides. The average activity concentrations of (40)K, (226)Ra and (232)Th in lignite are found to be 36 ± 8 Bq kg(-1), 9 ± 1 Bq kg(-1) and 9 ± 3 Bq kg(-1), respectively. Indications on the occurrence and geochemical behavior of uranium in the lignite matrix are suggested. The activity concentrations of natural radionuclides in fly ash and bottom ash samples are found to be concentrated from 3 to 5 times that of the feeding lignite. The external gamma-ray absorbed dose rate and the activity concentration index are calculated to assess the radiological hazard arising from ash disposal and recycling in the cement industry. Copyright © 2014 Elsevier Ltd. All rights reserved.

The German lignite industry. Historical development, resources, technology, economic structures and environmental impact. Study

International Nuclear Information System (INIS)

2017-05-01

Lignite has a key role to play in the transformation of the energy system due to its specific structural features in terms of industry, company history, policy, economics, the environment and regional structures. Understanding these structural features of the German lignite industry is an important requirement for classifying the significance of the lignite industry up to now and for the redesigning of this industrial sector. From these environmental, economic and regulatory structural characteristics, which are interwoven in a variety of ways, the incentives arise for the mining and power plant operators to react to energy price signals or energy policy steering. The aim of this research study is to define these structural features, to compile comprehensively the basic data and information that is not always transparently available, to understand the interactions, to enable the navigation of issues that are partly very complex, and to classify into the long-term developments that are especially important for political and social processes. In 2016 approx. 12 percent of German primary energy consumption was met using lignite. At the same time, lignite has the highest carbon dioxide (CO2) emissions of the fossil fuels; it currently accounts for approx. 19 percent of Germany's total greenhouse gas emissions as well as approx. 46 percent of the total CO2 emissions of the electricity sector. As a result of the mining of lignite and its conversion into electricity, substantial adverse impacts beyond the entry of greenhouse gases into the Earth's atmosphere arise for other environmental media. These impacts include half of Germany's mercury emissions, approx. a third of its sulfur dioxide emissions and approx. a tenth of its nitrogen oxide emissions. Lignite mining in open-cast mines takes up a substantial amount of landscape and soil and requires huge interventions in the water balance. Relatively high costs arise for the recultivation and rehabilitation of the open

Naturally occurring radioactive materials (NORMs) generated from lignite-fired power plants in Kosovo

International Nuclear Information System (INIS)

Hasani, F.; Shala, F.; Xhixha, G.; Xhixha, M.K.; Hodolli, G.; Kadiri, S.; Bylyku, E.; Cfarku, F.

2014-01-01

The energy production in Kosovo depends primarily on lignite-fired power plants. During coal combustion, huge amounts of fly ash and bottom ash are generated, which may result in enriched natural radionuclides; therefore, these radionuclides need to be investigated to identify the possible processes that may lead to the radiological exposure of workers and the local population. Lignite samples and NORMs of fly ash and bottom ash generated in lignite-fired power plants in Kosovo are analyzed using a gamma-ray spectrometry method for the activity concentration of natural radionuclides. The average activity concentrations of 40 K, 226 Ra and 232 Th in lignite are found to be 36 ± 8 Bq kg −1 , 9 ± 1 Bq kg −1 and 9 ± 3 Bq kg −1 , respectively. Indications on the occurrence and geochemical behavior of uranium in the lignite matrix are suggested. The activity concentrations of natural radionuclides in fly ash and bottom ash samples are found to be concentrated from 3 to 5 times that of the feeding lignite. The external gamma-ray absorbed dose rate and the activity concentration index are calculated to assess the radiological hazard arising from ash disposal and recycling in the cement industry. - Highlights: • NORMs in lignite combustion residues from CFPPs are studied. • Th/U indicates either low U uptake from host rocks and/or high leaching from peat. • The concentration factor of NORMs in fly and bottom ash samples are 3–5 times. • No 226 Ra enrichment is observed in fly ash while a depletion in bottom ash. • The reuse of fly ash in cement industry poses no significant radiological issue

Appraisal of Hydrologic Information Needed in Anticipation of Lignite Mining in Lauderdale County, Tennessee

Science.gov (United States)

Parks, William Scott

1981-01-01

Lignite in western Tennessee occurs as lenses or beds at various stratigraphic horizons in the Coastal Plain sediments of Late Cretaceous and Tertiary age. The occurrence of this lignite has been known for many decades, but not until the energy crisis was it considered an important energy resource. In recent years, several energy companies have conducted extensive exploration programs in western Tennessee, and tremendous reserves of lignite have been found. From available information, Lauderdale County was selected as one of the counties where strip-mining of lignite will most likely occur. Lignite in this county occurs in the Jackson and Cockfield Formations, undivided, of Tertiary age. The hydrology of the county is known only from regional studies and the collection of some site-specific data. Therefore, in anticipation of the future mining of lignite, a plan is needed for obtaining hydrologic and geologic information to adequately define the hydrologic system before mining begins and to monitor the effects of strip-mining once it is begun. For this planning effort, available hydrologic, geologic, land use, and associated data were located and compiled; a summary description of the surface and shallow subsurface hydrologic system was prepared: the need for additional baseline hydrologic information was outlined; and plans to monitor the effects of strip-mining were proposed. This planning approach, although limited to a county area, has transferability to other Coastal Plain areas under consideration for strip-mining of lignite.

The thar lignite project in the Sindh province, Pakistan

Energy Technology Data Exchange (ETDEWEB)

Hofmann, L. [RWE Power International, RE GmbH, Mining Dept., Koeln (Germany); Dittrich, W. [RWE Power International, RE GmbH, Mechanical and Electrical Dept., Koeln (Germany)

2005-05-01

A prospective area of the known lignite deposit located in the Thar region was investigated with regard to the future development of an opencast mine. For this purpose, a bankable feasibility study was prepared that evaluates all relevant facts and additional exploration activities. The study includes among others: Geological report; Opencast mine planning; Equipment and infrastructure planning; Assessment of staff requirements; Conceptual design of the power station; Anticipation of environmental aspects; Bankable costing for lignite mining and power generation. In conclusion, the development of an opencast mine and the construction of a 1000 MW power station are feasible in technical and economic terms. For the mine, the shovel/truck method was proposed since it offers cost advantages. For the power station, a closed cooling circuit and pre-drying of the lignite was recommended due to water shortage in the Thar desert. The resulting prices for power generation are usual market costs in Pakistan. (orig.)

French pollution and German lignite

International Nuclear Information System (INIS)

Foos, Jacques

2015-01-01

After having recalled that the German energy transition is based on a complete shutting down of nuclear power stations to replace them by renewable energy sources on the one hand, and by coal (lignite, i.e. the dirtiest coal) and gas on the other hand to compensate the intermittency of the former ones, this article notices that pollution peaks occurred in France when an eastern of north-eastern wind was blowing, and not in case of western wind. The author then wanders whether this pollution comes from Germany, and more particularly from the releases of lignite-fuelled power stations. Then, the author comments the high level of pollution associated with coal extraction and exploitation in Germany, causing thousands of deaths and resulting in lung diseases or cancers, myocardial infractions. The author then makes a parallel between, on the one hand, the ignorance of this German pollution and, on the other hand, evacuation measures around Fukushima for a radioactivity which the author considers as less dangerous in terms of life expectancy

The development of the Ptolemais lignite deposit, present situation and future perspective of the electrical energy market (Greece)

International Nuclear Information System (INIS)

Kavourides, Kostas

1997-01-01

PPC is by far the major producer of solid fuels in Greece. Currently the known exploitable reserves of solid fuels, are 4,0 billions tones of lignite and 4 billion cubic meters of peat. Mining of Lignite in Greece started in 1951 at the Aliveri underground mine and was continued at the open cast mines at Ptolemais (1955) and Megalopolis (1919). For more than 45 years. PPC has successfully exploited the Greece Lignite deposit for the production of electricity in order to satisfy the demand in Greece. Today PPC produces 60 million tons of lignite and handles approximately 275 million cubic meters of masses (overburden, lignite and interculated) per year. Lignite is the main energy resource in Greece and its combustion provides 75-80% of the electrical energy consumed in Greece.The Lignite Center of Ptolemais - Amyndeon (LCP-A) operated by the Greece PPC is located in northern Greece, about 110 km west of the city of Thessaloniki. The lignite deposits under exploitation cover an area. of 120 km 2 including 4000 Mt of proven geological reserves and 2700 Mt of exploitable lignite under current economic and technological criteria. Today LCP-A manages six active mines which in 1997 have a rate of handling 245 mil cubic meter of material and producing approx. 48 mil for of lignite. The continuous mining method which employs BWES, conveyors and strackers is the principal mining method used in all the lignite mines at the Ptolemais-Amyndeon Lignite Center. The implementation of selective mining procedures as well as discontinuous and /or combined mining methods differentiates the mining technology at the LCP-A from the respective technology applied in Germany lignite mines. The quality properties suggest that the lignite deposits in Greece are among the world's worst quality deposits exploited for energy production, where approximately 2 kg of lignite are consumed per I kWh of generated power. The main advantages of PPC'S coal orientated development program are the following

Desulfurization of organic sulfur from lignite by an electron transfer process

Energy Technology Data Exchange (ETDEWEB)

Demirbas, A. [Selcuk University, Konya (Turkey). Dept. for Chemical Engineering

2006-10-15

This study is an attempt to desulfurize organic sulfur from lignite samples with ferrocyanide ion as the electron transferring agent. Effect of temperature, particle size and concentration of ferrocyanide ion on desulfurization from the lignite samples has been investigated. The desulfurization process has been found to be continuous and gradually increases with increase of temperature from 298 to 368 K. The particle size has no significant impact on sulfur removal from the lignite samples. Particle size has no profound impact on the amount of sulfur removal. The desulfurization reaction has been found to be dependent on the concentration of potassium ferrocyanide. Gradual increase in the concentration of potassium ferrocyanide raised the magnitude of desulfurization, but at a higher concentration, the variation is not significant.

Reagent for treating clay drilling muds

Energy Technology Data Exchange (ETDEWEB)

Tkachenko, P V; Leshchinskiy, P A; Shnaper, B I; Zinchuk, I F; Zlobin, V P

1982-01-01

A reagent is proposed for treating clay drilling muds. It contains lignite, caustic soda and modifying agent. It is distinguished by the fact that in order to reduce the cost of the reagent with simultaneous decrease in the viscosity and static shear stress of the drilling mud, it additionally contains iron sulfate, and the modifying agent contained is wastes of carbonic acid production with the following ratio of components (parts by weight): lignite 10.0-15.0, caustic soda 2.0-3.0, wastes of carbonic acid production 0.5-0.75; iron sulfate 1.0-2.0.

Innovative approach to ash radioactivitiy and health impacts of lignite power plants

Energy Technology Data Exchange (ETDEWEB)

Bosevski, T.; Pop-Jordanova, N. [Macedonian Academy of Sciences and Arts, Skopje (Macedonia)

1998-12-31

In Macedonia nearly 90% of the present electricity production utilizes domestic low-calorie lignite, and this is likely to continue for the next few decades. Local and global environmental impacts of fossil fuel utilization are considered. Some innovative extensions to standard methodologies of environmental risk assessment and management are considered. They involve ash radioactivity and psychosomatic health impacts from lignite power plants. Two extensions are proposed: one comprising complete radioactive chains when determining committed effective dose from lignite ash; the other by including the psychosomatic diseases, such as peptic ulcer and arterial hypertension, due to chronic stress induced by power plants during normal operation. 7 refs., 2 figs., 3 tabs.

Sustainable development of lignite production on open cast mines in Serbia

Energy Technology Data Exchange (ETDEWEB)

Darko Danicic; Slobodan Mitrovic; Vladimir Pavlovic; Sava Kovacev [Kolubara Metal, Vreoci (Serbia)

2009-09-15

Currently operated coalmines in Serbia (Kolubara and Kostolac) have production around 36 million tons of lignite, and over 108 million m{sup 3} of overburden. Consequently, sustainability of lignite production requires cost reduction and environmental protection, as well as capacity increase. In order to rationalise, and increase efficiency of Serbian lignite mines, it is necessary to focus the activities on major issues shown within the triangle of energy policy objectives (security of supply, competitive prices and environmental protection). Production process optimisation singled out several special programs. Equipment revitalization and modernization is necessary taking into account that majority of the currently operated machinery has a life up to 25 years. Production process automation would enable high level of technical operation in the field of open cast mines management. Lack of coal quality uniformity is the permanent problem resulting by great amounts of coal reserves to be used uneconomically. Planning and training at all levels and finally cooperative software for business procedures and work order management. The measures suggested are a key precondition for maintaining competitive position of lignite production on international level. 7 refs., 5 figs., 1 tab.

Lignite utilisation for binding of radionuclides and uranium determination by adsorptive stripping chronopotentiometry

International Nuclear Information System (INIS)

Zavodska, L.

2010-01-01

This work in its first part deals with non-energetic use of young brown coal - lignite. The goal of the work was to perform a complex physical and chemical characterisation of the Slovak lignite (deposit Cary) which could contribute to rts use in binding of radionuclides in the environment. The characteristics of Slovak lignite were compared to leonardite (Gascoyne, USA) and Czech lignite (the area of Mikulcice). In the samples the residual humidity was determined. as well. as the content of ashes. representation of selected inorganic (As, Ba, Cd, Co, Cr, Cu, Ni, Pb and Zn) as well as organo-elements (C, H, N, 0, S) and crystalline forms of inorganic phase in lignite. The specific surface (BET isotherm) of lignite was determined, representation of total and free humic acids and their cation exchange capacity. The samples underwent al.so gamma-spectrometric analysis ( 40 K, 226 Ra, 228 Ac, 137 Cs and 60 Co). Using the radio-indicator method ( 85 Sr and 137 Cs) the kinetics of sorption of Cs + and Sr + ions in Slovak lignite was studied. The efficiency of sorption for both cations on lignite was evaluated on the basis of constructed sorption isotherms. The sorption of Cs + ions on Slovak lignite is more suitable for the Freundlich type of isotherm, in case of Sr + ions the sorption is better described by Langmuir isotherm. The results of sorption experiments on lignite in comparison with clinoptilolite and montmorillonite K-10 showed a more efficient sorption for Sr Ions. despite the more coarse-grained fraction of this matrix. This finding supports the possibility of lignite application for binding of a quite mobile radiostrontium, which may be applied for construction of radioactive waste repositories or for remediation of contaminated soils. The second part of the work deals with the development and validation of new fast and reliable electrochemical method of uranium determination in natural waters. It is based on physical adsorption of created complex of uranium

Thermal treating of acrylic matrices as a tool for controlling drug release.

Science.gov (United States)

Hasanzadeh, Davood; Ghaffari, Solmaz; Monajjemzadeh, Farnaz; Al-Hallak, M H D-Kamal; Soltani, Ghazal; Azarmi, Shirzad

2009-12-01

The purpose of the present study was to investigate the effect of thermal-treating on the release of ibuprofen from the granules prepared using aqueous dispersions of Eudragit. To accomplish this goal, different formulations were prepared using wet granulation method containing two different types of Eudragit aqueous dispersions, RS30D, RL30D and Avicel as filler. Tablets were prepared using direct compression method. The prepared tablets were thermally treated at 50 and 70 degrees C for 24 h. The drug release from tablets was assessed before and after thermal-treating. The results of release study showed that, thermally-treating the tablets at the temperatures higher than glass transition temperature (Tg) of the polymer can decrease the drug release from matrices. For mechanistic evaluation of the effect of thermal-treating, powder X-ray diffraction (XPD), scanning electron microscopy (SEM), differential scanning calorimeter (DSC), Fourier transform infrared (FT-IR) and helium pycnometer have been employed. The SEM graphs showed that the tablets have smoother surface with less porosity after thermal-treating. FT-IR spectra showed no change in the spectrum of thermally-treated tablet compared to control. In DSC graphs, no crystalline change was seen in the heat-treated samples of ibuprofen tablets, but decreased and widened peak size were related to the probable formation of solid solution of ibuprofen in Eudragit matrix. The results of helium pycnometer showed a significant decrease in the total porosity of some heat-treated samples. This study revealed the importance of thermal treating on the drug release from sustained release tablets containing Eudragit polymer.

The Evaluation Of Waste Plastic Burned With Lignite And Biomass

OpenAIRE

DURANAY, Neslihan; YILGIN, Melek

2016-01-01

In this work, the combustion behavior of pellets prepared from binary and triple blends of waste plastic, biomass and lignite was investigated in an experimental fixed bed combustion system. Market bags as plastic waste and the furniture factory waste powder as a source of biomass and Bingöl Karlıova coal as a lignite were used. The effect of process temperature and the plastic mixing ratio on the combustion behavior of pellets was studied. Combustion data obtained from varied bed temperature...

Expansion of the Neyveli lignite mine, India

Energy Technology Data Exchange (ETDEWEB)

Kasturi, T S [Neyveli Lignite Corp. Ltd., Tamil Nadu (India); Streck, W [Gold (O.) G.m.b.H. und Co. K.G., Koeln (Germany, F.R.)

1979-08-01

After giving a picture of the difficult winning conditions at the Neyveli open-cast lignite mine, the author states the reasons for the expansions of the open-cast mine and describes the necessary measures and machinery.

Swelling behavior of several bituminous coals and their thermally treated coals

Energy Technology Data Exchange (ETDEWEB)

Shui, Heng-fu; Cao, Mei-xia; Wang, Zhi-cai [Anhui University of Technology, Maanshan (China). School of Chemistry & Chemical Engineering

2007-07-01

The swelling behavior in different solvents of 4 bituminous coals with different ranks and their residues from extraction by CS{sub 2}/NMP mixed solvent (l:1 in volume) were measured. The change in swelling property of the four coals thermally treated at different temperature was observed. The results show that the swelling ratio decreases with increasing rank of coal. For lower rank bituminous coals the swelling ratios in polar solvent are higher than those in non-polar solvent, and this difference decreases with increasing rank. The cross-linking densities of the four residues decrease, and the swelling ratios increase compared with those of raw coals. The swelling ratios of the four thermally treated coals under 150{sup o}C in CS{sub 2} increase, suggesting the decrease in crosslinking density of them. When the thermal treatment temperature increases to 240{sup o}C, the swelling rations of the other three coals in NMP and CS{sub 2} increase again except gas coal, demonstrating the further decrease in crosslinking density. This result is coincident with the extraction yield change in the mixed solvent of the thermally treated coal. For example, the extraction yield of lean coal treated at 240{sup o}C increases from 6.9% to 17.3%. FT-IR results show the removal of oxygen group of the thermally treated coals. This may explain the increase in swelling ratio and extraction yield in the mixed solvent of coal after thermal treatment. The cross-linking density of the thermally treated coal decreases because of the break of hydrogen bonds due to removal of C = 0 and -OH oxygen groups during the thermal treatment, resulting in the increases of swelling ratio and extraction yield in the mixed solvent of thermally treated coal compared with those of raw coal. 15 refs., 3 figs., 6 tabs.

Production of rubbly culm coke from lignite

Energy Technology Data Exchange (ETDEWEB)

Koenigs, H B [Rheinische Braunkohlenwerke A.G., Koeln (Germany, F.R.). Hauptabteilung Kohleverarbeitung; Kurtz, R [Rheinische Braunkohlenwerke A.G., Frechen (Germany, F.R.). Abt. Verkokung und Chemie

1977-08-01

The article deals with the coke supply of the iron and steel industry, the design, function, and special features of the open-hearth, and describes the coking properties and applications of the culm coke produced from lignite.

Sedimentologic and palynologic significance of finding tertiary lignites in an ancient rift zone lake (Chingla, Ethiopia). Vol. 2

Energy Technology Data Exchange (ETDEWEB)

Kedamawit, Y.; Bonnefille, R.; Faure, H.; Taieb, M.

1984-01-01

Oligocene-Pleistocene deposits at Chingla apparently lie atop Miocene basalts. The upper cross-section shows numerous lignite interlayers. This paper discusses mineral composition of lignites and enclosing rock. Palynologic analysis of the lignite cross-sections determined 23 layers.

Biotechnological lignite conversion - a large-scale concept

Energy Technology Data Exchange (ETDEWEB)

Reich-Walber, M.; Meyrahn, H.; Felgener, G.W. [Rheinbraun AG, Koeln (Germany). Fuel Technology and Lab. Dept.

1997-12-31

Concerning the research on biotechnological lignite upgrading, Rheinbraun`s overall objective is the large-scale production of liquid and gaseous products for the energy and chemical/refinery sectors. The presentation outlines Rheinbraun`s technical concept for electricity production on the basis of biotechnologically solubilized lignite. A first rough cost estimate based on the assumptions described in the paper in detail and compared with the latest power plant generation shows the general cost efficiency of this technology despite the additional costs in respect of coal solubilization. The main reasons are low-cost process techniques for coal conversion on the one hand and cost reductions mainly in power plant technology (more efficient combustion processes and simplified gas clean-up) but also in coal transport (easy fuel handling) on the other hand. Moreover, it is hoped that an extended range of products will make it possible to widen the fields of lignite application. The presentation also points out that there is still a huge gap between this scenario and reality by limited microbiological knowledge. To close this gap Rheinbraun started a research project supported by the North-Rhine Westphalian government in 1995. Several leading biotechnological companies and institutes in Germany and the United States are involved in the project. The latest results of the current project will be presented in the paper. This includes fundamental research activities in the field of microbial coal conversion as well as investigations into bioreactor design and product treatment (dewatering, deashing and desulphurization). (orig.)

Stoichiometric calculations of combustion of Lakhra lignite

International Nuclear Information System (INIS)

Ali, I.; Ali, M.M.

2002-01-01

Lakhra coal field is largest productive coal field of Pakistan. About 1.5 millions tonne of this coal is, annually, mined and transported daily to various parts of the country in 500 trucks each of 10 tonnes of coal. The major consumers of this coal are brick kilns located in Sindh and Punjab. It is available at Rs. 500/- per tonne at mine head. A number of attempts were made for the production of power (electricity) by foreign companies. Feasibility studies were undertaken but no one set up power plant. It may be due to inferior quality of coal as it is lignitic in nature with high ash and sulfur contents. This coal is also, very sensitive to spontaneous combustion. Spontaneous combustion is the auto-ignition of coal at ambient conditions. Hence there are storage problems. In spite of these drawbacks, a 3(50) Mega Watt (3 units of each 50 mega watt power generation capacity) power plant, based on atmospheric fluidized bed combustion of coal technology (AFBC), was setup in early nineties. The performance of this plant remained poor. The main reasons might be poor quality of coal and limestone. Limestone is used with high sulfur Lakhra lignite, in fluidized bed combustor, to arrest sulfur of the coal, fixing sulfur as calcium sulfate to minimize hazardous emissions of sulfur dioxide (SO/sub 2/). Spontaneous combustion of Lakhra lignite is responsible for each fire of coal and conveyor belt etc. (author)

Structural degradation of Thar lignite using MW1 fungal isolate: optimization studies

Science.gov (United States)

Haider, Rizwan; Ghauri, Muhammad A.; Jones, Elizabeth J.; Orem, William H.; SanFilipo, John R.

2015-01-01

Biological degradation of low-rank coals, particularly degradation mediated by fungi, can play an important role in helping us to utilize neglected lignite resources for both fuel and non-fuel applications. Fungal degradation of low-rank coals has already been investigated for the extraction of soil-conditioning agents and the substrates, which could be subjected to subsequent processing for the generation of alternative fuel options, like methane. However, to achieve an efficient degradation process, the fungal isolates must originate from an appropriate coal environment and the degradation process must be optimized. With this in mind, a representative sample from the Thar coalfield (the largest lignite resource of Pakistan) was treated with a fungal strain, MW1, which was previously isolated from a drilled core coal sample. The treatment caused the liberation of organic fractions from the structural matrix of coal. Fungal degradation was optimized, and it showed significant release of organics, with 0.1% glucose concentration and 1% coal loading ratio after an incubation time of 7 days. Analytical investigations revealed the release of complex organic moieties, pertaining to polyaromatic hydrocarbons, and it also helped in predicting structural units present within structure of coal. Such isolates, with enhanced degradation capabilities, can definitely help in exploiting the chemical-feedstock-status of coal.

Steam gasification of Bulmer coal in the presence of lignite ash

Energy Technology Data Exchange (ETDEWEB)

Palmer, A.; Furimsky, E.

1986-01-01

Steam gasification of blends prepared from Balmer coal and the ash from combustion of Onakawana lignite was performed in a fixed bed reactor. The blends were prepared by co-slurrying followed by drying. In the presence of 20 wt% ash the gasification rate doubled at 830 and 930 C. Direct blending of coal and lignite resulted in an overall increase in carbon conversion at 830 C but had no effect at 930 C. 5 refs.

Trigeneration integrated with absorption enhanced reforming of lignite and biomass

Energy Technology Data Exchange (ETDEWEB)

Yaodong Wang; Ye Huang; Anthony P. Roskilly [Newcastle University, Newcastle Upon Tyne (United Kingdom). Sir Joseph Swan Institute for Energy Research

2009-10-15

A technical investigation of an innovative trigeneration integrated with absorption enhanced reforming (AER) of lignite and biomass is carried out using the ECLIPSE process simulator. The system includes an internal combustion engine, an AER gasifier, a waste heat recovery and storage unit and an absorption refrigerator. The whole system is operated in the following sequence: The AER gasifier is used to generate hydrogen using lignite and biomass; the hydrogen generated is used to run the engine which drives a generator to produce electricity. Additionally, the heat recovery unit collects waste heat from the engine and is used to supply hot water and space heating. Furthermore, the waste heat is used to operate the absorption refrigerator. The electricity, heat and cooling can be used to meet the energy requirements for the households in a village, a resident building or a commercial building, or a supermarket. Within the study, the effects of lignite mixed with three different types of biomass (straw, willow and switch grass) on the system performance are investigated and the results are compared. The results show that it is feasible to use an AER system to reform the low quality fuels lignite and biomass to generate a cleaner fuel - hydrogen to replace fossil fuels (diesel or natural gas) and to fuel an engine based trigeneration system; the system works with high efficiencies and with a potential of carbon capture from the sorbent-regeneration process that would benefit the environment. 25 refs., 2 figs., 3 tabs.

Enhancing Carbon Reactivity in Mercury Control in Lignite-Fired Systems

Energy Technology Data Exchange (ETDEWEB)

Chad Wocken; Michael Holmes; John Pavlish; Jeffrey Thompson; Katie Brandt; Brandon Pavlish; Dennis Laudal; Kevin Galbreath; Michelle Olderbak

2008-06-30

This project was awarded through the U.S. Department of Energy (DOE) National Energy Technology Laboratory Program Solicitation DE-PS26-03NT41718-01. The Energy & Environmental Research Center (EERC) led a consortium-based effort to resolve mercury (Hg) control issues facing the lignite industry. The EERC team-the Electric Power Research Institute (EPRI); the URS Corporation; the Babcock & Wilcox Company; ADA-ES; Apogee; Basin Electric Power Cooperative; Otter Tail Power Company; Great River Energy; Texas Utilities; Montana-Dakota Utilities Co.; Minnkota Power Cooperative, Inc.; BNI Coal Ltd.; Dakota Westmoreland Corporation; the North American Coal Corporation; SaskPower; and the North Dakota Industrial Commission-demonstrated technologies that substantially enhanced the effectiveness of carbon sorbents to remove Hg from western fuel combustion gases and achieve a high level ({ge} 55% Hg removal) of cost-effective control. The results of this effort are applicable to virtually all utilities burning lignite and subbituminous coals in the United States and Canada. The enhancement processes were previously proven in pilot-scale and limited full-scale tests. Additional optimization testing continues on these enhancements. These four units included three lignite-fired units: Leland Olds Station Unit 1 (LOS1) and Stanton Station Unit 10 (SS10) near Stanton and Antelope Valley Station Unit 1 (AVS1) near Beulah and a subbituminous Powder River Basin (PRB)-fired unit: Stanton Station Unit 1 (SS1). This project was one of three conducted by the consortium under the DOE mercury program to systematically test Hg control technologies available for utilities burning lignite. The overall objective of the three projects was to field-test and verify options that may be applied cost-effectively by the lignite industry to reduce Hg emissions. The EERC, URS, and other team members tested sorbent injection technologies for plants equipped with electrostatic precipitators (ESPs) and

Petrographic Composition of Lignite from the Lake Somerville Spillway (East-central Texas)

Science.gov (United States)

Pawelec, Sandra; Bielowicz, Barbara

2017-12-01

In the presented paper, the macroscopic and microscopic composition of lignite from Lake Somerville Spillway has been examined. The study area is the upper part of the Manning Formation, located north-west of Somerville in the central-eastern part of Texas. There are three exposures: NE, SW and MC (Main Central) with visible parts of late-Eocene lignite seams belonging to the Jackson Group. The Manning section is divided into four marine dominated parasequences (P1 through P4). Lignite samples outlining the P1 parasequence from the MC and NE outcrops and the argillate sample from the lower part of the P2 parasequence, NE outcrop. Macroscopic characterization was carried out based on lithological classifications of humic coal. On this basis, it has been shown that the main lithotype occurring in the deposit is detritic (matrix) coal with a high share of mineral matter. The maceral composition of coal was determined according to the ICCP guidelines. The macerals from liptinite group were determined under fluorescent light. The maceral group content analysis was performed with use of 500-600 equally spaced points on the surface of the polished sections. It has been found that the examined coal is dominated by macerals from the huminite group, with a share ranging from 20.8 to 65.3% volume, including atrinite (9.8-22.8% volume, 17.5% volume on average). In the examined coal, macerals from the inertinite group (10.1 to 44.8%), especially semifusinite (max. 13.9%), fusinite (max. 9.3%) and funginite (max. 6.3 %) are of particularly large share. In the liptinite group, particular attention was paid to the content of alginite (max. 4.5%) and bituminite (max. 1.3 %), which indicate the paralic sedimentation environment of the examined coal. Additionally, the variability of macerals and maceral groups within the exposures and levels of the P1 parasequence was examined. The last step was to compare lignite from Lake Somerville Spillway with other lignites belonging to the

Potential use of California lignite and other alternate fuel for enhanced oil recovery. Phase I and II. Final report. [As alternative fuels for steam generation in thermal EOR

Energy Technology Data Exchange (ETDEWEB)

Shelton, R.; Shimizu, A.; Briggs, A.

1980-02-01

The Nation's continued reliance on liquid fossil fuels and decreasing reserves of light oils gives increased impetus to improving the recovery of heavy oil. Thermal enhanced oil recovery EOR techniques, such as steam injection, have generally been the most effective for increasing heavy oil production. However, conventional steam generation consumes a large fraction of the produced oil. The substitution of alternate (solid) fuels would release much of this consumed oil to market. This two-part report focuses on two solid fuels available in California, the site of most thermal EOR - petroleum coke and lignite. Phase I, entitled Economic Analysis, shows detailed cost comparisons between the two candidate fuels and also with Western coal. The analysis includes fuels characterizations, process designs for several combustion systems, and a thorough evaluation of the technical and economic uncertainties. In Phase II, many technical parameters of petroleum coke combustion were measured in a pilot-plant fluidized bed. The results of the study showed that petroleum coke combustion for EOR is feasible and cost effective in a fluidized bed combustor.

Wettability modification of Wender lignite by adsorption of dodecyl poly ethoxylated surfactants with different degree of ethoxylation: A molecular dynamics simulation study.

Science.gov (United States)

Zhang, Lei; Li, Bao; Xia, Yangchao; Liu, Shengyu

2017-09-01

Lignite is an important and useful fossil fuel in the world and the strong hydrophilicity of it limits its applications. Surfactant adsorption on lignite is an effective way to make it hydrophobic. In this work, aiming to examine the effect of the degree of ethoxylation on the adsorption behavior of dodecyl poly ethoxylated surfactants on lignite and the wettability modification of modified lignite by surfactant adsorption, different combined systems formed by surfactants, water and a model surface of Wender lignite have been studied using molecular dynamics simulation. The adsorption configurations vary with the degree of ethoxylation. At the same adsorption amounts, increasing the degree of ethoxylation can make the adsorption layer more compactness and bring stronger adsorption strength. The results of binding energy and its components show that the adsorption of alkyl polyoxyethylene ethers surfactant on lignite is physically adsorbed rather than electrostatically or chemisorbed. Meanwhile, van der Waals interaction plays a dominant role in the adsorption. The addition of surfactant could reduce the possibility of the interaction between water and lignite. Compared to the original lignite, the interaction between them is weakened after surfactant adsorption in water/surfactant/lignite system, thus strengthening the hydrophobicity of lignite. Similar to the adsorption strength, hydrophobicity of modified lignite increases with the increase of the degree of ethoxylation. The lignite surface properties are changed due to surfactant adsorption by analyzing the compositions of interaction energy and the change of hydrogen bonds. Copyright © 2017 Elsevier Inc. All rights reserved.

Effect of mineral oxides on slag formation tendency of Mae Moh lignites

Directory of Open Access Journals (Sweden)

Anuwat Luxsanayotin

2010-08-01

Full Text Available Slagging is one of major ash deposition problems experienced in the boilers of coal–fired power plants especially theplants that use lignite, like Mae Moh lignites. The occurrence of slag is a complex phenomenon depending on several factorssuch as ash properties, furnace operating conditions, and coal properties. The main objective of this work is to study theeffect of mineral components in Mae Moh lignite on ash fusion temperatures (AFTs, which is commonly used as a keyindicator for slag formation tendency under pulverized combustion conditions. Two Mae Moh lignites from the coal seamsplanned to be used in the future were selected for the study to represent low CaO and high CaO lignite. The two lignites,namely K1 and K3, have 3.6 and 40.4 wt% CaO in ash, respectively. The AFT characterization shows that their initial deformationtemperatures (ITs were almost identical and considered as low for the typical flue gas temperature in the radiationsection of Mae Moh boilers, i.e. 1050-1100°C. These observed similar ITs were rather unexpected, especially for K1 consideringits sufficiently low base to acid (B/A ratios. The X-ray diffraction analyses evidently show the presence of illite, pyriteand anhydrite in K1, which explains the observed lower IT of the sample. Anhydrite, which is known to lower the ITs, is alsothe most abundant mineral in K3. Washing the lignite samples with HCl can significantly reduce CaO, MgO, and SO3 contentin the ash but not Fe2O3 as it is present in the form of pyrite. The addition of Al2O3, SiO2 and Fe2O3 can help increase AFTs ofthe studied samples. The Al2O3 addition gives the strongest effect on increasing AFTs, especially for the sample with lowAl2O3 content. When the CaO is added to the low CaO samples, the fluxing effect will initially occur. However, when the CaOcontent is higher than a critical value (i.e. CaO > 38%, the effect of its high melting point will dominate hence the AFTsincreased. Ternary phase diagrams

Organic petrology, mineralogy and depositional environment of the Kipra lignite seam, Maritza-West basin, Bulgaria

Energy Technology Data Exchange (ETDEWEB)

Kostova, Irena [Department of Geology and Palaeontology, Sofia University ' ' St. Kliment Ohridski' ' , 1000, Sofia (Bulgaria); Zdravkov, Alexander [Department of Economic Geology, University of Mining and Geology ' ' St. Ivan Rilski' ' , 1700, Sofia (Bulgaria)

2007-08-01

The aim of the present study is to provide additional information about the properties and depositional environment of the Kipra lignite seam, which was deposited during the regressive stage of development of the Maritza-West basin. Petrographical and mineralogical data, along with ash yields and sulphur contents of 24 samples from a seam profile, have been used to study the vertical variation of the depositional settings during peat accumulation and subsequent coalification. The Kipra lignite is characterized by high ash yields and sulphur contents. It formed in a rheotrophic, low-lying mire with alkaline pH value. Vegetation with low preservation potential dominated within the palaeomire. During peat formation, frequent changes of the water level controlled the depositional environment. During the deposition of units 1 and 2, high water energy caused the transportation of high amounts of inorganic material into the mire, resulting in the formation of weakly gelified mineral-rich lignite. The organic matter from units 3 and 4 is characterized by enhanced gelification, which probably reflects the decreasing energy of the system. Good positive correlation between sulphur contents and the GI values was established in units 4, indicating that the gelification of the tissues was probably mainly controlled by the bacterial activity. In contrast, the gelification of the samples from unit 3 of the Kipra seam was probably governed by the redox conditions. The organic matter deposited under relatively wet conditions, in which the thermal and oxidative destruction of the tissues, was limited. A variety of major, minor and accessory minerals are present in Maritza-West lignite. The mineral composition is dominated mainly by pyrite, gypsum and calcite, and to a lesser extent limonite, quartz, kaolinite, montmorillonite, illite, chlorite and plagioclase. Jarosite, hematite, halloysite, mica, K-feldspar, aragonite, siderite, and dolomite were also determined in very low

Characteristics of Mae Moh lignite: Hardgrove grindability index and approximate work index

OpenAIRE

Wutthiphong Tara; Chairoj Rattanakawin

2012-01-01

The purpose of this research was to preliminarily study the Mae Moh lignite grindability tests emphasizing onHardgrove grindability and approximate work index determination respectively. Firstly, the lignite samples were collected,prepared and analyzed for calorific value, total sulfur content, and proximate analysis. After that the Hardgrove grindabilitytest using ball-race test mill was performed. Knowing the Hardgrove indices, the Bond work indices of some samples wereestimated using the A...

Thermal-treated soil for mercury removal: Soil and phytotoxicity tests

Energy Technology Data Exchange (ETDEWEB)

Roh, Y.; Edwards, N.T.; Lee, S.Y.; Stiles, C.A.; Armes, S.; Foss, J.E.

2000-04-01

Mercury (Hg) contamination of soils and sediments is one of many environmental problems at the Oak Ridge Reservation, Oak Ridge, TN. Mercury-contaminated soil from the Lower East Fork Poplar Creek (LEFPC) at the Oak Ridge Reservation was treated thermally to reduce Hg concentration to a below target level (20 mg kg{sup {minus}1}) as a pilot scale thermal treatment demonstration. As a part of performance evaluation, the soil characteristics and plant growth response of the untreated and treated soil were examined. The soil treated at 350 C retained most of its original soil properties, but the soil treated at 600 C exhibited considerable changes in mineralogical composition and physicochemical characteristics. Growth and physiological response of the three plant species radish (Raphanus sativus L.), fescue (Festuca arundinacea Schreb.), and oat (Avena sativa L.) indicated adverse effects of the thermal treatment. The addition of N fertilizer had beneficial effects in the 350 C treated soil, but had little beneficial effect in the 600 C treated soil. Some changes of soil characteristics induced by thermal treatment cannot be avoided. Soil characteristics and phytotoxicity test results strongly suggest that changes occurring following the 350 C treatment do not limit the use of the treated soil to refill the excavated site for full-scale remediation. The only problem with the 350 C treatment is that small amounts of Hg compounds (<15 mg kg{sup {minus}1}) remain in the soil and a processing cost of $45/Mg.

Atmospheric Fluidized Bed Combustion testing of North Dakota lignite

Energy Technology Data Exchange (ETDEWEB)

Goblirsch, G; Vander Molen, R H; Wilson, K; Hajicek, D

1980-05-01

The sulfur retention by the inherent alkali, and added limestone sorbent, perform about the same and are reasonably predictable within a range of about +-10% retention by application of alkali to sulfur ratio. Temperature has a substantial effect on the retention of sulfur by the inherent alkali or limestone. The temperature effect is not yet fully understood but it appears to be different for different coals and operational conditions. The emission of SO/sub 2/ from the fluid bed burning the Beulah lignite sample used for these tests can be controlled to meet or better the current emission standards. The injection of limestone to an alkali-to-sulfur molar ratio of 1.5 to 1, should lower the SO/sub 2/ emissions below the current requirement of 0.6 lb SO/sub 2//10/sup 6/ Btu to 0.4 lb SO/sub 2//10/sup 6/ Btu, a safe 33% below the standard. Agglomeration of bed material, and consequent loss of fluidization quality can be a problem when burning high sodium lignite in a silica bed. There appears, however, to be several ways of controlling the problem including the injection of calcium compounds, and careful control of operating conditions. The heat transfer coefficients measured in the CPC and GFETC tests are comparable to data obtained by other researchers, and agree reasonably well with empirical conditions. The NO/sub x/ emissions measured in all of the tests on Beulah lignite are below the current New Source Performance Standard of 0.5 lb NO/sub 2//10/sup 6/ Btu input. Combustion efficiencies for the Beulah lignite are generally quite high when ash recycle is being used. Efficiencies in the range of 98% to 99%+ have been measured in all tests using this fuel.

COFIRING BIOMASS WITH LIGNITE COAL

Energy Technology Data Exchange (ETDEWEB)

Darren D. Schmidt

2002-01-01

The University of North Dakota Energy & Environmental Research Center, in support of the U.S. Department of Energy's (DOE) biomass cofiring program, completed a Phase 1 feasibility study investigating aspects of cofiring lignite coal with biomass relative to utility-scale systems, specifically focusing on a small stoker system located at the North Dakota State Penitentiary (NDSP) in Bismarck, North Dakota. A complete biomass resource assessment was completed, the stoker was redesigned to accept biomass, fuel characterization and fireside modeling tests were performed, and an engineering economic analysis was completed. In general, municipal wood residue was found to be the most viable fuel choice, and the modeling showed that fireside problems would be minimal. Experimental ash deposits from firing 50% biomass were found to be weaker and more friable compared to baseline lignite coal. Experimental sulfur and NO{sub x} emissions were reduced by up to 46%. The direct costs savings to NDSP, from cogeneration and fuel saving, results in a 15- to 20-year payback on a $1,680,000 investment, while the total benefits to the greater community would include reduced landfill burden, alleviation of fees for disposal by local businesses, and additional jobs created both for the stoker system as well as from the savings spread throughout the community.

Acid leaching of coal: to produce clean fuels from Turkish lignite

Energy Technology Data Exchange (ETDEWEB)

Seferinoglu, Meryem [Mineral Research and Exploration Directorate (Turkey)], email: meryem_seferinoglu66@yahoo.com; Duzenli, Derya [Ankara Central Laboratory (Turkey)

2011-07-01

With the increasing concerns about the environment, energy producers and governments are looking at developing clean energy sources. However, Turkey has limited clean energy resources and is using low grade coal which has high sulphur content as an alternative energy source. The aim of this paper is to study the possibility of generating clean fuel from Edirne Lignite and to get a better understanding of chemical mechanisms involved in coal leaching with hydrofluoric acid (HF) solutions. Leaching was conducted on Edirne Lignite with HF solution at ambient temperature and the effects of parameters such as reaction time and concentration of acid solutions on the process were evaluated. The optimum conditions were found and it was shown that ash levels can be reduced from 28.9% to 10.5% and the calorific value increased by 500kcal/kg with the HF leaching method. This study demonstrated that the production of clean fuel from high sulphur lignite is possible.

Influence of chemical structure on carbon isotope composition of lignite

Science.gov (United States)

Erdenetsogt, Bat-Orshikh; Lee, Insung; Ko, Yoon-Joo; Mungunchimeg, Batsaikhan

2017-04-01

During the last two decades, a number of studies on carbon isotopes in terrestrial organic matter (OM) have been carried out and used to determine changes in paleoatmospheric δ13C value as well as assisting in paleoclimate analysis. Coal is abundant terrestrial OM. However, application of its δ13C value is very limited, because the understanding of changes in isotopic composition during coalification is relatively insufficient. The purpose of this study was to examine the influence of the chemical structure on the carbon isotope composition of lignite. Generally, lignite has more complex chemical structures than other higher rank coal because of the existence of various types of oxygen-containing functional groups that are eliminated at higher rank level. A total of sixteen Lower Cretaceous lignite samples from Baganuur mine (Mongolia) were studied by ultimate, stable carbon isotope and solid-state 13C CP/MAS NMR analyses. The carbon contents of the samples increase with increase in depth, whereas oxygen content decreases continuously. This is undoubtedly due to normal coalification process and also consistent with solid state NMR results. The δ13C values of the samples range from -23.54‰ to -21.34‰ and are enriched in 13C towards the lowermost samples. Based on the deconvolution of the NMR spectra, the ratios between carbons bonded to oxygen (60-90 ppm and 135-220 ppm) over carbons bonded to carbon and hydrogen (0-50 ppm and 90-135 ppm) were calculated for the samples. These correlate well with δ13C values (R2 0.88). The results indicate that the δ13C values of lignite are controlled by two mechanisms: (i) depletion in 13C as a result of loss of isotopically heavy oxygen-bounded carbons and (ii) enrichment in 13C caused by a loss of isotopically light methane from aliphatic and aromatic carbons. At the rank of lignite, coal is enriched in 13C because the amount of isotopically heavy CO2 and CO, released from coal as a result of changes in the chemical

Solid substrate fermentation of lignite by the coal-solubilizing mould, Trichoderma atroviride, in a new type of bioreactor

Energy Technology Data Exchange (ETDEWEB)

Holker, U.; Hofer, M. [University of Bonn, Bonn (Germany)

2002-07-01

Trichoderma atroviride CBS 349 is able to solubilize lignite. The mould was cultured under non-sterile conditions in a new type of bioreactor for solid substrate fermentation. German lignite (lithotype A, Bergheim) was used as complex solid substrate. Over 40 days 140 g of 1.5 kg lignite held in a 25 1-bioreactor was solubilized by the fungus.

A comparative study of nitrogen conversion during pyrolysis of coconut fiber, its corresponding biochar and their blends with lignite.

Science.gov (United States)

Liu, Zhengang; Balasubramanian, Rajasekhar

2014-01-01

In the present study, the conversion of fuel-N to HCN and NH3 was investigated during rapid pyrolysis of raw biomass (coconut fiber), its corresponding biochar and their blends with lignite within a temperature range of 600-900°C. The results showed that the raw biomass and the biochar showed totally different nitrogen partitioning between NH3 and HCN. HCN was the dominant nitrogen pollutant from pyrolysis of raw biomass, while for the biochar pyrolysis the yield of NH3 was slightly higher than that of HCN. Synergistic interactions occurred within both raw biomass/lignite and biochar/lignite blends, especially for the biochar/lignite blend, and resulted in reduced yields of HCN and NH3, decreased the total nitrogen percentage retained in the char and promoted harmless N2 formation. These findings suggest that biochar/lignite co-firing for energy production may have the enhanced benefit of reduced emissions of nitrogen pollutants than raw biomass/lignite. Copyright © 2013 Elsevier Ltd. All rights reserved.

Fates and roles of alkali and alkaline earth metal species during the pyrolysis and gasification of a Victorian lignite

Energy Technology Data Exchange (ETDEWEB)

Mody, D.; Wu, H.; Li, C. [Monash University, Vic. (Australia). CRC for Clean Power from Lignite, Dept. of Chemical Engineering

2000-07-01

The transformation of alkali and alkaline earth metal (AAEM) species in a Victorian lignite during the pyrolysis and subsequent gasification in CO{sub 2} was studied in a novel quartz fluidised-bed reactor. Lignite samples prepared by physically adding NaCl and ion-exchanging Na{sup +} and Ca{sup ++} into the lignite were used to investigate the effects of chemical forms and valency of the AAEM species in the substrate lignite on their transformation during pyrolysis and gasification. Carboxyl-bound Na was found to be less volatile than Na present as NaCl, but more volatile than carboxyl-bound Ca during pyrolysis at temperatures between 400 and 900{sup o}C. However, the carboxyl-bound Na was volatilised to a much greater extent than the carboxyl-bound Ca in the same lignite during pyrolysis. It was seen that the loading of NaCl into the lignite did not significantly affect the char reactivity in the fluidised-bed reactor at 900{sup o}C.

A study relating to the conceptual design and cost estimates of the Saskatchewan Power Corporation lignite beneficiation process

Energy Technology Data Exchange (ETDEWEB)

Granatstein, D L; Champagne, P J; Szladow, A J

1982-06-01

The purpose is to provide technology for upgrading lignite to a cleaner fuel that is capable of improving utility plant operation and is more acceptable to the non-utility sector. Beneficiated lignite can provide a middle alternative between low-grade and high-grade fuels. The results for phase IV include a conceptual design for a lignite beneficiation plant and a marketing study for the product. The beneficiated lignite is cheaper to transport, easier to handle, cleaner, allows better plant operation with higher availability, reduced slagging and fouling, reduced sulphur, and lower operating and maintenance costs. 8 refs., 6 figs., 7 tabs.

Carbon Nanostructure of Kraft Lignin Thermally Treated at 500 to 1000 °C.

Science.gov (United States)

Zhang, Xuefeng; Yan, Qiangu; Leng, Weiqi; Li, Jinghao; Zhang, Jilei; Cai, Zhiyong; Hassan, El Barbary

2017-08-21

Kraft lignin (KL) was thermally treated at 500 to 1000 °C in an inert atmosphere. Carbon nanostructure parameters of thermally treated KL in terms of amorphous carbon fraction, aromaticity, and carbon nanocrystallites lateral size ( L a ), thickness ( L c ), and interlayer space ( d 002 ) were analyzed quantitatively using X-ray diffraction, Raman spectroscopy, and high-resolution transmission electron microscopy. Experimental results indicated that increasing temperature reduced amorphous carbon but increased aromaticity in thermally treated KL materials. The L c value of thermally treated KL materials averaged 0.85 nm and did not change with temperature. The d 002 value decreased from 3.56 Å at 500 °C to 3.49 Å at 1000 °C. The L a value increased from 0.7 to 1.4 nm as temperature increased from 500 to 1000 °C. A nanostructure model was proposed to describe thermally treated KL under 1000 °C. The thermal stability of heat treated KL increased with temperature rising from 500 to 800 °C.

Leaching of arsenic, copper and chromium from thermally treated soil.

Science.gov (United States)

Kumpiene, Jurate; Nordmark, Désirée; Hamberg, Roger; Carabante, Ivan; Simanavičienė, Rūta; Aksamitauskas, Vladislovas Česlovas

2016-12-01

Thermal treatment, if properly performed, is an effective way of destroying organic compounds in contaminated soil, while impact on co-present inorganic contaminants varies depending on the element. Leaching of trace elements in thermally treated soil can be altered by co-combusting different types of materials. This study aimed at assessing changes in mobility of As, Cr and Cu in thermally treated soil as affected by addition of industrial by-products prior to soil combustion. Contaminated soil was mixed with either waste of gypsum boards, a steel processing residue (Fe 3 O 4 ), fly ash from wood and coal combustion or a steel abrasive (96.5% Fe 0 ). The mixes and unamended soil were thermally treated at 800 °C and divided into a fine fraction 0.125 mm to simulate particle separation occurring in thermal treatment plants. The impact of the treatment on element behaviour was assessed by a batch leaching test, X-ray absorption spectroscopy and dispersive X-ray spectrometry. The results suggest that thermal treatment is highly unfavourable for As contaminated soils as it increased both the As leaching in the fine particle size fraction and the mass of the fines (up to 92%). Soil amendment with Fe-containing compounds prior to the thermal treatment reduced As leaching to the levels acceptable for hazardous waste landfills, but only in the coarse fraction, which does not justify the usefulness of such treatment. Among the amendments used, gypsum most effectively reduced leaching of Cr and Cu in thermally treated soil and could be recommended for soils that do not contain As. Fly ash was the least effective amendment as it increased leaching of both Cr and As in majority of samples. Copyright © 2016 Elsevier Ltd. All rights reserved.

The catalytic cracking mechanism of lignite pyrolysis char on tar

International Nuclear Information System (INIS)

Lei, Z.; Huibin, H.; Xiangling, S.; Zhenhua, M.; Lei, Z.

2017-01-01

The influence of different pyrolysis conditions for tar catalytic cracking will be analyzed according to the lignite pyrolysis char as catalyst on pyrolytic tar in this paper. The pyrolysis char what is the by-product of the cracking of coal has an abundant of pore structure and it has good catalytic activity. On this basis, making the modified catalyst when the pyrolysis char is activation and loads Fe by impregnation method. The cracking mechanism of lignite pyrolytic tar is explored by applying gas chromatograph to analyze splitting products of tar. The experimental results showed that: (1) The effect of tar cracking as the pyrolysis temperature, the heating rate, the volatilization of pyrolysis char and particle size increasing is better and better. The effect of the catalytic and cracking of lignite pyrolysis char in tar is best when the heating rate, the pyrolysis temperature, the volatiles of pyrolysis char, particle size is in specific conditions.(2) The activation of pyrolysis char can improve the catalytic effect of pyrolysis char on the tar cracking. But it reduces the effect of the tar cracking when the pyrolysis char is activation loading Fe. (author)

Properties and potential of formed cokes derived from two Turkish lignites by carbonization of binderless briquettes

Energy Technology Data Exchange (ETDEWEB)

Bayraktur, K.N.; Lawson, G.J.

1984-09-01

Two high-sulphur Turkish lignites were briquetted at room temperature under pressures of 113 or 212 MPa and the briquettes were carbonized to 1158-1173 K over special heating cycles. The lowerrank lignite gave a formed coke of superior mechanical strength, lower porosity and higher sulphur content than typical blast furnace cokes. The formed coke produced from the higher-rank lignite briquettes had slightly poorer mechanical strength, lower porosity and much higher ash and sulphur content than conventional cokes. The products were considered attractive for use in non-ferrous metallurgy.

Properties and potential of formed cokes derived from two Turkish lignites by carbonization of binderless briquettes

Energy Technology Data Exchange (ETDEWEB)

Bayraktar, K.N.; Lawson, G.J.

1984-09-01

Two high-sulphur Turkish lignites were briquetted at room temperature under pressures of 113 or 212 MPa and the briquettes were carbonized to 1158-1173 K over special heating cycles. The lower-rank lignite gave a formed coke of superior mechanical strength, lower porosity and higher sulphur content than typical blast furnace cokes. The formed coke produced from the higher-rank lignite briquettes had slightly poorer mechanical strength, lower porosity and much higher ash yield and sulphur content than conventional cokes. The products were considered attractive for use in non-ferrous metallurgy. 38 references.

JV Task 90 - Activated Carbon Production from North Dakota Lignite

Energy Technology Data Exchange (ETDEWEB)

Steven Benson; Charlene Crocker; Rokan Zaman; Mark Musich; Edwin Olson

2008-03-31

The Energy & Environmental Research Center (EERC) has pursued a research program for producing activated carbon from North Dakota lignite that can be competitive with commercial-grade activated carbon. As part of this effort, small-scale production of activated carbon was produced from Fort Union lignite. A conceptual design of a commercial activated carbon production plant was drawn, and a market assessment was performed to determine likely revenue streams for the produced carbon. Activated carbon was produced from lignite coal in both laboratory-scale fixed-bed reactors and in a small pilot-scale rotary kiln. The EERC was successfully able to upgrade the laboratory-scale activated carbon production system to a pilot-scale rotary kiln system. The activated carbon produced from North Dakota lignite was superior to commercial grade DARCO{reg_sign} FGD and Rheinbraun's HOK activated coke product with respect to iodine number. The iodine number of North Dakota lignite-derived activated carbon was between 600 and 800 mg I{sub 2}/g, whereas the iodine number of DARCO FGD was between 500 and 600 mg I{sub 2}/g, and the iodine number of Rheinbraun's HOK activated coke product was around 275 mg I{sub 2}/g. The EERC performed both bench-scale and pilot-scale mercury capture tests using the activated carbon made under various optimization process conditions. For comparison, the mercury capture capability of commercial DARCO FGD was also tested. The lab-scale apparatus is a thin fixed-bed mercury-screening system, which has been used by the EERC for many mercury capture screen tests. The pilot-scale systems included two combustion units, both equipped with an electrostatic precipitator (ESP). Activated carbons were also tested in a slipstream baghouse at a Texas power plant. The results indicated that the activated carbon produced from North Dakota lignite coal is capable of removing mercury from flue gas. The tests showed that activated carbon with the greatest

Pyrolysis kinetics of phenols from lignite semicoking tar

Energy Technology Data Exchange (ETDEWEB)

Platonov, V.V.; Polovetskaya, O.S.; Proskuryakov, V.A.; Shavyrina, O.A. [Leo Tolstoy Tula State Pedag University, Tula (Russian Federation)

2002-11-01

The features of pyrolysis of phenols from lignite semicoking tar were studied. The activation energy and order of the reactions of accumulation of methane, hydrogen, carbon monoxide and dioxide, naphthalene and its methyl homologs, phenols, and isomeric cresols and dimethylphenols were determined.

Environmental Assessment for Lignite Fuel Enhancement Project, Coal Creek Station, Great River Energy, Underwood, North Dakota

Energy Technology Data Exchange (ETDEWEB)

N/A

2004-01-16

The US Department of Energy (DOE) has prepared this EA to assess the environmental impacts of the commercial application of lignite fuel enhancement. The proposed demonstration project would be implemented at Great River Energy's Coal Creek Station near Underwood, North Dakota. The proposed project would demonstrate a technology to increase the heating value of lignite and other high-moisture coals by reducing the moisture in the fuels. Waste heat that would normally be sent to the cooling towers would be used to drive off a percentage of the moisture contained within the lignite. Application of this technology would be expected to boost power-generating efficiencies, provide economic cost savings for lignite and sub-bituminous power plants, and reduce air emissions. The proposed project would be constructed on a previously disturbed site within the Coal Creek Station and no negative impacts would occur in any environmental resource area.

The influence of water quality on the reuse of lignite-derived waters in the Latrobe Valley, Australia

Energy Technology Data Exchange (ETDEWEB)

C.J. Butler; A.M. Green; L. Chaffee [Monash University, Churchill, Vic. (Australia). CRC for Clean Power from Lignite, School of Applied Sciences and Engineering

2005-03-01

Mechanical Thermal Expression (MTE), a novel non-evaporative brown coal (lignite) dewatering process, is being developed to increase the efficiency of power stations in the Latrobe Valley (Victoria, Australia). A by-product of this process is a large volume (potentially 20 giga liters per annum) of product water stream. This paper examines water quality requirements for reuse and disposal within the Latrobe Valley and their compatibility with MTE process water. It has been established that remediation of this water will be required and that the maintenance of environmental flows in surface waters would be the most suitable use for the remediated water.

Combustion characteristics and air pollutant formation during oxy-fuel co-combustion of microalgae and lignite.

Science.gov (United States)

Gao, Yuan; Tahmasebi, Arash; Dou, Jinxiao; Yu, Jianglong

2016-05-01

Oxy-fuel combustion of solid fuels is seen as one of the key technologies for carbon capture to reduce greenhouse gas emissions. The combustion characteristics of lignite coal, Chlorella vulgaris microalgae, and their blends under O2/N2 and O2/CO2 conditions were studied using a Thermogravimetric Analyzer-Mass Spectroscopy (TG-MS). During co-combustion of blends, three distinct peaks were observed and were attributed to C. vulgaris volatiles combustion, combustion of lignite, and combustion of microalgae char. Activation energy during combustion was calculated using iso-conventional method. Increasing the microalgae content in the blend resulted in an increase in activation energy for the blends combustion. The emissions of S- and N-species during blend fuel combustion were also investigated. The addition of microalgae to lignite during air combustion resulted in lower CO2, CO, and NO2 yields but enhanced NO, COS, and SO2 formation. During oxy-fuel co-combustion, the addition of microalgae to lignite enhanced the formation of gaseous species. Copyright © 2016 Elsevier Ltd. All rights reserved.

COFIRING BIOMASS WITH LIGNITE COAL; FINAL

International Nuclear Information System (INIS)

Darren D. Schmidt

2002-01-01

The University of North Dakota Energy and Environmental Research Center, in support of the U.S. Department of Energy's (DOE) biomass cofiring program, completed a Phase 1 feasibility study investigating aspects of cofiring lignite coal with biomass relative to utility-scale systems, specifically focusing on a small stoker system located at the North Dakota State Penitentiary (NDSP) in Bismarck, North Dakota. A complete biomass resource assessment was completed, the stoker was redesigned to accept biomass, fuel characterization and fireside modeling tests were performed, and an engineering economic analysis was completed. In general, municipal wood residue was found to be the most viable fuel choice, and the modeling showed that fireside problems would be minimal. Experimental ash deposits from firing 50% biomass were found to be weaker and more friable compared to baseline lignite coal. Experimental sulfur and NO(sub x) emissions were reduced by up to 46%. The direct costs savings to NDSP, from cogeneration and fuel saving, results in a 15- to 20-year payback on a$1,680,000 investment, while the total benefits to the greater community would include reduced landfill burden, alleviation of fees for disposal by local businesses, and additional jobs created both for the stoker system as well as from the savings spread throughout the community

Fractal morphology in lignite coal: a small angle x-ray scattering investigation

International Nuclear Information System (INIS)

Chitra, R.; Sen, D.; Mazumder, S.; Chandrasekaran, K.S.

1999-01-01

Small angle x-ray scattering technique has been used to study the pore morphology in lignite coal from Neyveli lignite mine (Tamilnadu, India). The sample were collected from three different locations of the same mine. SAXS profiles from all the three samples show almost identical functionality, irrespective of the locations from where the samples were collected. SAXS experiment using two different wavelengths also exhibit same functionality indicating the absence of multiple scattering. The analysis indicates the surface fractal nature of the pore morphology. The surface fractal dimension is calculated to be 2.58. (author)

Reactivity of chars prepared from the pyrolysis of a Victorian lignite under a wide range of conditions

Energy Technology Data Exchange (ETDEWEB)

Wu, H.; Mody, D.; Li, C.; Hayashi, J.; Chiba, T. [Monash University, Vic. (Australia). CRC for Clean Power from Lignite, Dept. of Chemical Engineering

2000-07-01

A Loy Yang lignite sample was pyrolysed under a wide range of experimental conditions using a wire-mesh reactor, a fluidised-bed reactor, a drop-tube reformer and a thermogravimetric analyser (TGA). The reactivity of these char samples in CO{sub 2} and air was measured in the TGA as well as in the fluidised-bed reactor. A sample prepared by the physical impregnation of NaCl into the lignite was also used in order to investigate the effect of NaCl in the lignite on the reactivity of the resulting char. Our experimental results indicate that, due to the volatilisation of a substantial fraction of Na in the lignite substrate during pyrolysis, the true catalytic activity of the Na in the lignite substrate should be evaluated by measuring the sodium content in the char after pyrolysis. The char reactivity measured in situ in the fluidised-bed reactor was compared with that of the same char measured separately in the TGA after re-heating the char sample to the same temperature as that in the fluidised-bed. It was found that the re-heating of the char in the TGA reduced the char reactivity.

Report on the survey of abandoned uraniferous lignite mines in southwestern North Dakota

International Nuclear Information System (INIS)

Lyon, R.J.; Prochaska, D.; Burgess, J.L.; Patrick, D.

1986-03-01

A radiation survey was conducted in October 1983 as part of the proposed reclamation plan of abandoned uraniferous lignite mines in southwestern North Dakota. The survey was made to determine the extent of contamination caused by mining operations in the 1960's. Radiation measurements were made and soil samples were taken at approximately 300 locations around six mine sites comprising eleven lignite mine pits. Toxic element analysis was also done on 50 of the soil samples

LARGE-SCALE MECURY CONTROL TECHNOLOGY TESTING FOR LIGNITE-FIRED UTILITIES-OXIDATION SYSTEMS FOR WET FGD

Energy Technology Data Exchange (ETDEWEB)

Michael J. Holmes; Steven A. Benson; Jeffrey S. Thompson

2004-03-01

The Energy & Environmental Research Center (EERC) is conducting a consortium-based effort directed toward resolving the mercury (Hg) control issues facing the lignite industry. Specifically, the EERC team--the EERC, EPRI, URS, ADA-ES, Babcock & Wilcox, the North Dakota Industrial Commission, SaskPower, and the Mercury Task Force, which includes Basin Electric Power Cooperative, Otter Tail Power Company, Great River Energy, Texas Utilities (TXU), Montana-Dakota Utilities Co., Minnkota Power Cooperative, BNI Coal Ltd., Dakota Westmoreland Corporation, and the North American Coal Company--has undertaken a project to significantly and cost-effectively oxidize elemental mercury in lignite combustion gases, followed by capture in a wet scrubber. This approach will be applicable to virtually every lignite utility in the United States and Canada and potentially impact subbituminous utilities. The oxidation process is proven at the pilot-scale and in short-term full-scale tests. Additional optimization is continuing on oxidation technologies, and this project focuses on longer-term full-scale testing. The lignite industry has been proactive in advancing the understanding of and identifying control options for Hg in lignite combustion flue gases. Approximately 1 year ago, the EERC and EPRI began a series of Hg-related discussions with the Mercury Task Force as well as utilities firing Texas and Saskatchewan lignites. This project is one of three being undertaken by the consortium to perform large-scale Hg control technology testing to address the specific needs and challenges to be met in controlling Hg from lignite-fired power plants. This project involves Hg oxidation upstream of a system equipped with an electrostatic precipitator (ESP) followed by wet flue gas desulfurization (FGD). The team involved in conducting the technical aspects of the project includes the EERC, Babcock & Wilcox, URS, and ADA-ES. The host sites include Minnkota Power Cooperative Milton R. Young

Spring Barley Yield Parameters after Lignite, Sodium Humate and Nitrogen Utilization

Directory of Open Access Journals (Sweden)

Kováčik Peter

2016-10-01

Full Text Available The existence of a small number of publications dealing with the impact of solid sodium humate and lignite on the quantity and quality of grown crops was the reason for establishing the field experiment. The objective of this experiment was to detect the impact of solid lignite and solid sodium humate on the quantity and quality of spring barley yield. These substances were applied into the soil either independently or along with nitrogen fertiliser. The next objective was to determine the impact of foliar application of sodium humate water solution applied either independently or along with nitrogen fertiliser on the quality and quantity of spring barley yield. The achieved results showed that the autumn application of solid lignite and the presowing application of solid sodium humate into the soil tended to decrease the yield of both grain and straw of spring barley, crude protein content in grain, proportion of the first-class grains and volume weight of grain, whereas the impact of humate was more negative. Lignite and sodium humate in the solid form should be used along with nitrogen fertiliser. The application of sodium humate in liquid form during the growth season of barley tended to increase the yield of both grain and straw. The joint application of nitrogen and liquid sodium humate during the growth season of barley increased the grain yield of barley significantly. A lower dose of nitrogen, applied during the growth season of barley (growth season BBCH 23, increased the grain yield of barley considerably more than a higher N dose, applied into the soil before barley sowing.

Production of heavy greases from lignite

Energy Technology Data Exchange (ETDEWEB)

1921-03-18

A process is described for the extraction of heavy greases and wagon greases and their equivalents, by separation from bitumins, resins, and waxes contained in lignite, peat, bituminous shale, fossil wax, paraffin, etc., characterized by the fact that for the extraction are used solvents of high boiling point, such as mineral oils, grease oils, tar oils, and other equivalents, which are not eliminated and at the same time constitute a part of the product obtained.

Rapid restoration after lignite mining in Hungary

Energy Technology Data Exchange (ETDEWEB)

1988-06-01

The 30th anniversary of the commencement of large scale lignite production by opencast mining in Hungary was celebrated in 1987. A process of rapid technical and biological reclamation without the use of humus has now been developed. The costs involved are only 5-10% of those of conventional methods and reclamation cycle is four years compared to ten years for conventional methods.

Reclamation of a uraniferous lignite mine, North Dakota: summary paper

International Nuclear Information System (INIS)

Houghton, R.L.; Hall, R.L.; Unseth, J.D.; Wald, J.D.; Burgess, J.L.; Patrick, D.P.; Anderson, G.S.; Hill, S.R.

1987-01-01

Uraniferous lignite deposits were mined from 1955 to 1967 by surface mining techniques. Overburden was stripped, and the lignite was burned to concentrate the uranium in its ash. Uranium salts in the overburden gave exposure levels of as much as 500 microroentgens/hour; water in mine pits had U concentrations from 12 to 19,000 micrograms/liter. Reclamation involved replacing the spoils into the source pit, the most contaminated spoils being placed above the water table, capping the pit with clay then topsoil containing lesser concentrations of radioactive elements, and finally planting with prairie grass. Resulting concentrations of radionuclides are given. The land is expected to remain as prairie for wildlife use, but it is safe enough for domestic animals as well. 3 figures

Bioprocessing of lignite coals using reductive microorganisms. Final technical report, September 30, 1988--March 29, 1992

Energy Technology Data Exchange (ETDEWEB)

Crawford, D.L.

1992-03-29

In order to convert lignite coals into liquid fuels, gases or chemical feedstock, the macromolecular structure of the coal must be broken down into low molecular weight fractions prior to further modification. Our research focused on this aspect of coal bioprocessing. We isolated, characterized and studied the lignite coal-depolymerizing organisms Streptomyces viridosporus T7A, Pseudomonas sp. DLC-62, unidentified bacterial strain DLC-BB2 and Gram-positive Bacillus megaterium strain DLC-21. In this research we showed that these bacteria are able to solubilize and depolymerize lignite coals using a combination of biological mechanisms including the excretion of coal solublizing basic chemical metabolites and extracellular coal depolymerizing enzymes.

Combustion behavior of different kinds of torrefied biomass and their blends with lignite.

Science.gov (United States)

Toptas, Asli; Yildirim, Yeliz; Duman, Gozde; Yanik, Jale

2015-02-01

In this study, the combustion behavior of different kinds of torrefied biomass (lignocellulosic and animal wastes) and their blends with lignite was investigated via non-isothermal thermogravimetric method under air atmosphere. For comparison, combustion characteristics of raw biomasses were also determined. Torrefaction process improved the reactivity of char combustion step of biomasses. Characteristic combustion parameters for blends showed non-additivity behavior. It was found that the mixture of torrefied biomasses and lignite at a ratio of 1:1 had a lower ignition and burnout temperature than the coal-only sample. Although no interactions were observed between the lignite and torrefied biomass at initial step of combustion, a certain degree of interaction between the components occurred at char combustion step. Kinetic parameters of combustion were calculated by using the Coats Redfern model. Overall, this study showed that poultry litters can be used as a substitute fuel in coal/biomass co-firing systems by blending with lignocellulosic biomass. Copyright © 2014 Elsevier Ltd. All rights reserved.

Influence of geological variations on lignite drying kinetics in superheated steam atmosphere for Belchatow deposit located in the central Poland

Directory of Open Access Journals (Sweden)

Sciazko Anna

2016-01-01

Full Text Available Lignite-fired coal power plants suffer from a significant heat loss due to the high moisture content in this energy carrier. Water removal from fuel is an indispensable treatment for improving the combustion process, which will foster the efficient utilization of lignite. Superheated steam fluidized bed drying is expected for this purpose in a power generation sector. Understanding drying kinetics of lignite will greatly reinforce design process of a dryer. Physical features as well as the drying behaviour may be divergent among the lignite originated from different depths and positions in a certain mine. To reveal and clarify the influence of the geological features, the drying characteristics of several grades of lignite from the Belchatow mine in Poland were investigated. The attempts to clarify the influence of the divergent properties of the investigated samples on the drying kinetics in superheated steam were presented in this paper.

The reduction of sulfate ions in Musashino woody lignite and in acetone-furfural resin

Energy Technology Data Exchange (ETDEWEB)

Kimura, T.

1986-01-01

By adding a barium chloride solution to sulfur-containing woody lignite kept in water for two years, it has been confirmed that large quantities of sulfate ions are adsorbed by the lignite. Furthermore, spectroscopic measurements have confirmed the reduction of sulfate ions in an acetone-furfural resin prepared with residual sulfuric acid. These experimental results suggest the possibility of reducing sulfate ions in coal in the absence of sulfate bacteria. 2 refs.

PILOT-AND FULL-SCALE DEMONSTRATION OF ADVANCED MERCURY CONTROL TECHNOLOGIES FOR LIGNITE-FIRED POWER PLANTS

Energy Technology Data Exchange (ETDEWEB)

Steven A. Benson; Charlene R. Crocker; Kevin C. Galbreath; Jay R. Gunderson; Michael J. Holmes; Jason D. Laumb; Jill M. Mackenzie; Michelle R. Olderbak; John H. Pavlish; Li Yan; Ye Zhuang

2005-02-01

The overall objective of the project was to develop advanced innovative mercury control technologies to reduce mercury emissions by 50%-90% in flue gases typically found in North Dakota lignite-fired power plants at costs from one-half to three-quarters of current estimated costs. Power plants firing North Dakota lignite produce flue gases that contain >85% elemental mercury, which is difficult to collect. The specific objectives were focused on determining the feasibility of the following technologies: Hg oxidation for increased Hg capture in dry scrubbers, incorporation of additives and technologies that enhance Hg sorbent effectiveness in electrostatic precipitators (ESPs) and baghouses, the use of amended silicates in lignite-derived flue gases for Hg capture, and the use of Hg adsorbents within a baghouse. The approach to developing Hg control technologies for North Dakota lignites involved examining the feasibility of the following technologies: Hg capture upstream of an ESP using sorbent enhancement, Hg oxidation and control using dry scrubbers, enhanced oxidation at a full-scale power plant using tire-derived fuel and oxidizing catalysts, and testing of Hg control technologies in the Advanced Hybrid{trademark} filter.

Experiments and stochastic simulations of lignite coal during pyrolysis and gasification

International Nuclear Information System (INIS)

Ahmed, I.I.; Gupta, A.K.

2013-01-01

Highlights: ► Lignite pyrolysis and gasification has been conducted in a semi batch reactor. ► The objective is to understand mechanism of syngas evolution during pyrolysis. ► Stochastic simulations of lignite pyrolysis were conducted using Gillespie algorithm. ► First order, single step mechanism failed to fit cumulative yield of hydrogen. ► Evolution of hydrogen via pyrolysis of gaseous hydrocarbon following bridges scission. -- Abstract: Lignite pyrolysis and gasification has been conducted in a semi batch reactor at reactor temperatures of 800–950 °C in 50 °C intervals. CO 2 has been used as the gasifying agent for gasification experiments. The objective of this investigation is to understand the mechanism of syngas evolution during pyrolysis and to unravel the effect of CO 2 on pyrolysis mechanism. Stochastic simulations of lignite pyrolysis have been conducted using Gillespie algorithm. Two reaction mechanisms have been used in the simulations; first order, single step mechanism and the FLASHCHAIN mechanism. The first order single step mechanism was successful in fitting cumulative yield of CO 2 , CO, CH 4 and other hydrocarbons (C n H m ). The first order, single step failed to fit the cumulative yield of hydrogen, which suggests a more complex mechanism for hydrogen evolution. Evolution of CO 2 , CO, CH 4 , C n H m and H 2 flow rates has been monitored. The only effect of CO 2 on pyrolysis mechanism is promotion of reverse water gas shift reaction for the experiments described here. Methane evolution extended for slightly longer time than other hydrocarbons and hydrogen evolution extended for a slightly longer time than methane. This indicated the evolution of hydrogen via further pyrolysis of aliphatic hydrocarbon. It is also suggested that this step occurs in series after aliphatic hydrocarbons evolution by bridges scission.

Distribution of vesicular-arbuscular mycorrhizal fungi in coal, lignite and calcite mine spoils of India

Energy Technology Data Exchange (ETDEWEB)

Ganesan, V.; Ragupathy, S.; Parthipan, B.; Rani, D.B.R.; Mahadevan, A.

1991-12-31

Vesicular-arbuscular mycorhizzal (VAM) status was assessed for coal, lignite and calcite mine spoils. The three study sites were: The Kothagudem coal field in the south central region where waste materials are piled 1 to 2 m high on the soil surface. Samples were collected from plants growing on the waste. Neyveli, on the southeastern coast, is a lignite coal mine where the spoil is piled 70 to 100 m high on the soil surface. Samples were collected from recently revegetated mine spoil and from 25 year old revegetated sites. The calcite mine at Thazhaiyuthu in the south where the spoil is piled up 2 to 3 m on the soil surface. Samples were collected from 4 to 7 year old reclaimed sites. The wastes generally supported different plant species. The level of VAM infection of plants was markedly different in each mine spoil, with the maximum infection in the coal and calcite spoils, and the least in the lignite spoil. There was more infection in the 25 year old lignite spoil than in the newly revegetated spoil. There were different VAM species in each spoil, and no one species was present in all of the samples. The authors conclude that one of the factors leading to the differences between spoils is the amount of topsoil contained in the spoil (least in the lignite spoils which are very deep). The other is age of the spoils. Unfortunately the authors concluded that the best approach is to enrich the spoils with VAM rather than salvaging and replacing topsoil

Petrology, palynology and organic geochemistry of Eocene lignite of Matanomadh, Kutch Basin, western India: Implications to depositional environment and hydrocarbon source potential

Energy Technology Data Exchange (ETDEWEB)

Dutta, Suryendu; Mathews, Runcie P.; Saraswati, Pratul K.; Banerjee, Santanu [Department of Earth Sciences, Indian Institute of Technology Bombay (India); Singh, Bhagwan D.; Tripathi, Suryakant M.; Singh, Alpana [Birbal Sahni Institute of Palaeobotany, Lucknow (India); Mann, Ulrich [Forschungszentrum Juelich (Germany). Institut fuer chemie und Dynamik der Geosphaere

2011-01-01

Petrological, palynological and organic-geochemical investigations were undertaken to determine the source vegetation, depositional conditions and hydrocarbon source potential of Eocene Matanomadh lignites from Kutch Basin, western India. The maceral study reveals that studied lignites are rich in huminite (av. 63%) with sub-ordinate amount of liptinite (av. 19%) and low inertinite (av. 3%), along with low to moderately high associated mineral matters (av. 15%). The overall petrographic composition points to a lagoonal condition for the formation of these lignites. The mean huminite reflectance values (R{sub r}: 0.28-0.34%, av. 0.31%) as well as low Rock-Eval T{sub max} (av. 417 C) values for the seams, suggest brown coal or lignitic stage/rank for the studied lignites. The palynological assemblages, dominated by tropical angiospermic pollen, suggest prevalence of warm humid tropical climate during the deposition of these lignites. The total organic carbon (TOC) content of lignites ranges between 26 and 58 wt.%, whereas the TOC content of the associated carbonaceous shales is around 4 wt.%. The Hydrogen Index (HI) ranging from 23 to 452 mg HC/g TOC indicates that the lignite sequence has the potential to produce mixed oil and gaseous hydrocarbons on maturation. The major pyrolysis products of lignites, derived from Curie point pyrolysis-GC-MS, are straight chain aliphatics, phenols and cadalene-based C{sub 15} bicyclic sesquiterpenoids. The exclusive occurrence of C{sub 15} bicyclic sesquiterpenoids suggests that these compounds are derived from dammar resin of angiosperm plants, belonging to family Dipterocarpaceae. (author)

Pre-treating water with non-thermal plasma

Science.gov (United States)

Cho, Young I.; Fridman, Alexander; Rabinovich, Alexander; Cho, Daniel J.

2017-07-04

The present invention consists of a method of pre-treatment of adulterated water for distillation, including adulterated water produced during hydraulic fracturing ("fracking") of shale rock during natural gas drilling. In particular, the invention is directed to a method of treating adulterated water, said adulterated water having an initial level of bicarbonate ion in a range of about 250 ppm to about 5000 ppm and an initial level of calcium ion in a range of about 500 ppm to about 50,000 ppm, said method comprising contacting the adulterated water with a non-thermal arc discharge plasma to produce plasma treated water having a level of bicarbonate ion of less than about 100 ppm. Optionally, the plasma treated water may be further distilled.

Perspectives of the non-energetic use of lignite in Germany

Energy Technology Data Exchange (ETDEWEB)

Keller, D.; Sailer, B. [RWE Power AG, Essen (Germany)

2013-11-01

RWE Power AG as integral part of RWE Generation SE has been active in the development and commercialization of coal gasification routes for many years. RWE Generation SE is one of Europe's leading electricity producers and combines the expertise of the power plant specialists Essent (NL), RWE npower (UK) and RWE Power (D). A globally increasing freight traffic and accompanying fuel demand is anticipated in the future. This higher demand will probably result in an increase in crude oil price in the course of the next years. There will also be a disproportionately high increase in fuel prices additionally to the increase in the crude oil price due to an increasing treatment effort within refineries. Therefore the substitution of crude oil becomes more and more attractive in view of economical perspectives and security of supply. Crude oil is not only to be substituted as feedstock for fuels but also for the chemical industry. Coal has been and will be the most important feedstock for this. Especially its gasification enables various routes. In Germany there is also an interesting perspective for Coal-to-Liquids and Coal-to-Gas or CtL/CtG as the non-energetic use of coal is abbreviated. Lignite is available regardless of any market impacts and currently faces a change in its use for power generation due to the increasing use of renewable energies. Hence lignite is an attractive feedstock for CtL/CtG in Germany. The construction of a commercial size CtL/CtG plant means a billion Euro investment. So a reliable economic evaluation is inevitable. Today all CtL/CtG routes miss commercial competitiveness to the conventional production by some ten percents. In case the current upward price trend of crude oil continues CtL/CtG might become viable in the near future. The production of synthetic fuels appears most attractive in view of a substantial market potential. The further commercialization of gasification routes in Germany requires R and D activities especially

Comparative study of German and Greek lignite mine reclamation

International Nuclear Information System (INIS)

Dietrich, N.L.

1994-01-01

The reclamation planning of three European lignite mining districts are compared: amount and extent of planning, integration with mining operations, and results. The districts are: Rheinbraun (Cologne), Leipzig-Borna (''East'' Germany), and Megalopolis (Greece). Lignite mines were visited and mining and reclamation personnel interviewed. The Rheinbraun mines have the most thorough reclamation operations. The integrated mine and reclamation operations are world class in size, scope, and detail of reclamation. A comprehensive landscape and reclamation plan is required in the mine permitting process. The Leipzig-Borna district is the second largest of the districts, studied little pre-mining planning of the post-mining landscape or land uses was evident. Reclamation is not closely integrated with the mining and typically occurs many years after the mining. Reduced lignite production since German reunification has left vast areas of disturbed land with little mining; and no funding for the reclamation of the large areas of mined land reclamation. The Greek Megalopolis mines have mine operations plan, but with no integrated reclamation planning. The initial spoil pile was reclaimed according to the original German mining plan. No pits have been reclaimed, and spoil areas are revegetated sporadically. The Rheinbraun mining operations Cologne which include a post mining landscape/land use plan have integrated and timely reclamation operations. The other two mining operations, which do not have a comprehensive and detailed reclamation and landscape/land use plans, do not integrate reclamation operations with the mining operations. The results are large areas of mined land unreclaimed for many years

Potentials and limitations of spatial and demographic development in Kosovo-Metohija lignite basin

Directory of Open Access Journals (Sweden)

Spasić Nenad

2009-01-01

Full Text Available The initial research carried out for the purpose of elaborating the Spatial Plan for Kosovo-Metohija Lignite Basin indicated the need to address numerous conflicts and opposing interests in the area concerned. This required the Plan to focus on harmonizing the economic, social and spatial aspects of developing a mining-energy-industrial system (hereinafter MEIS and its surroundings, devising the new ways for the protection of local population interests and use of novel approaches in dealing with the environmental consequences of lignite exploitation and processing. The area wherein Kosovo-Metohija lignite deposits are found is replete with diverse conflicting interests, including insufficient and uneven development, extremely large overall and especially agrarian population density (among the highest in Europe, unemployment and a sizable portion of the grey economy, low level and quality of services of public interest, ethnic conflicts and polarization, etc. The environmental effects of MEIS activities in a situation of this kind were revealed by the early stages of research in all segments of economic, social and spatial development, along with a high degree of environmental degradation. The main conflict in the Plan area is the one between mining and agriculture, i.e. open pit lignite mining and high-fertility soil covering lignite deposits. The conflict is additionally aggravated by the remarkable density of agricultural population on this territory and high selling prices of the land. Therefore, a substantial part of the Plan’s propositions was related to the conditions of settlement and infrastructure relocation, population resettlement and measures to relieve the tensions and prevent the outbreak of potential conflicts in implementing the Plan. The Spatial Plan is conceived as a complex and comprehensive document defining the framework, basic principles, starting points and measures tackling the numerous development conflicts, spatial

Characterization of Physical and Thermal Properties of Biofield Treated Neopentyl Glycol

OpenAIRE

Trivedi , Mahendra Kumar; Tallapragada , Rama Mohan; Branton , Alice; Trivedi , Dahryn; Nayak , Gopal; Mishra , Rakesh; Jana , Snehasis

2015-01-01

International audience; Neopentyl glycol (NPG) has been extensively used as solid-solid phase change materials (PCMs) for thermal energy storage applications. The objective of the present study was to evaluate the impact of biofield treatment on physical, spectral and thermal properties of NPG. The study was performed in two groups (control and treated). The control group remained as untreated, and treatment group was subjected to Mr. Trivedi’s biofield treatment. The control and treated NPG ...

Analysis of gas-phase mercury sorption with coke and lignite dust

Directory of Open Access Journals (Sweden)

Marczak Marta

2017-01-01

Full Text Available In recent years the problem of mercury emission became a widely discussed topic. Its high impact is caused by its toxicity and ability to accumulate in living organisms, properties that justified the United States Environmental Protection Agency (US EPA to classify mercury as hazardous pollutant. The problem of mercury emission is crucial for countries like Poland, where the most of the emission is caused by coaldepended energy sector. Current technology of mercury removal utilizes adsorption of mercury on the surface of activated carbon. Due to high price of activated carbon, this technological approach seems to be uneconomical and calls for cheaper alternative. One possible solution can be usage of other sorptive materials obtained from thermal processes like coke production. Example of such material is coke dust obtained from dry quenching of coke. The aim of this work was to analyse the sorption potential of lignite and coke dust and determine parameters influencing mercury behaviour during combustion.

Mineralogy and geochemistry of density-separated Greek lignite fractions

NARCIS (Netherlands)

Iordanidis, A.; Doesburg, van J.D.J.

2006-01-01

In this study, lignite samples were collected from the Ptolemais region, northern Greece, homogenized, crushed to less than I nun, and separated in three density fractions using heavy media. The mineralogical investigation of the density fractions showed a predominance of pyrite in the light

Characterization of Physical and Thermal Properties of Biofield Treated Neopentyl Glycol

OpenAIRE

Trivedi, Dahryn; Trivedi, Mahendra Kumar; Branton, Alice; Nayak, Gopal

2015-01-01

Neopentyl glycol (NPG) has been extensively used as solid-solid phase change materials (PCMs) for thermal energy storage applications. The objective of the present study was to evaluate the impact of biofield treatment on physical, spectral and thermal properties of NPG. The study was performed in two groups (control and treated). The control group remained as untreated, and treatment group was subjected to Mr. Trivedi’s biofield treatment. The control and treated NPG were characterized by X-...

Determination of ash-forming elements in lignite coal

International Nuclear Information System (INIS)

Wischnewski, C.; Werner, G.; Vogt, J.; Just, G.

1990-01-01

The most important methods are discussed suitable for the determination of ash-forming elements in coal. In this connection questions of the concentrations of elements in lignites, of the sample preparation, and of the selection of methods for the determination of ash-forming elements are addressed. Advantages and disadvantages of different analysis techniques are shown using concrete examples. (author)

An overview of underground coal gasification and its applicability for Turkish lignite

Energy Technology Data Exchange (ETDEWEB)

Pekpak, E.; Yoncaci, S.; Kilic, M.G. [Middle East Technical Univ., Ankara (Turkey). Dept. of Mining Engineering

2010-07-01

Coal is expected to maintain its significance as an energy source for a longer time period than oil and natural gas. Environmental concerns have led to the development of clean coal technologies, such as coal gasification. Coal gasification can be used at either at surface or in underground coal gasification (UCG). UCG has several advantages over surface gasification and conventional mining such as rank low calorific value coals. Coal gasification also has the potential to contribute to the energy supply of a country. Most Turkish coals are lignite and UCG may enable diversification of energy sources of Turkey and may help decrease external dependency on energy. This paper presented a study that matched a UCG technique to the most appropriate (Afsin Elbistan) lignite reserve in Turkey. Two UCG techniques were presented, including the linked vertical well method, and the directional drilling-controlled retractable injection point (CRIP) method. The properties of coal seams and coal properties were also outlined. It was concluded that Cobanbey is the most preferable sector in the Elbistan Lignite Reserve for a pilot study, and that the linked vertical well method could be considered as a candidate method. 17 refs., 6 tabs., 1 fig.

Solubilization of low-rank coal by Trichoderma atroviride: Evidence for the involvement of hydrolytic and oxidative enzymes by using C-14-labelled lignite

Energy Technology Data Exchange (ETDEWEB)

Holker, U.; Schmiers, H.; Grosse, S.; Winkelhofer, M.; Polsakiewicz, M.; Ludwig, S.; Dohse, J.; Hofer, M. [University of Bonn, Bonn (Germany). Inst. of Botany

2002-04-01

The deuteromycete Trichoderma atroviride is able to solubilize lignite in dependence on a given carbon source for growth. When cultivated on media containing glutamate, this mold excreted a set of different enzymes with hydrolytic activity. Addition of lignite to the growth media induced the synthesis of extracellular lignite-specific esterase activity but no evidence has been provided for its direct involvement in the process of lignite solubilization. Hence, the basic capability of T. atroviride enzymes to degrade a variety of ester and ether bonds at the surface or within the bulky lignite structure was tested using coal following its direct labelling with C-14-alkyl iodide. The participation of hydrolytic and oxidative enzymes in lignite degradation was assessed by measuring the release of C-14 radioactivity from selectively alkylated carboxylic and phenolic OH groups. T. atroviride cleaved both carboxylic esters using esterases and the phenolic ether bonds by using oxidative enzymes, most likely laccases.

Organic geochemistry of the Lower Miocene Oberdorf lignite (Styrian Basin, Austria): its relation to petrography, palynology and the palaeoenvironment

Energy Technology Data Exchange (ETDEWEB)

Bechtel, A.; Sachsenhofer, R.F.; Kolcon, I.; Gratzer, R. [Institut fuer Geowissenschaften, Prospektion und Angewandte Sedimentologie, Montanuniversitaet Leoben, Peter-Tunner-Str. 5, A-8700 Leoben (Austria); Otto, A.; Puettmann, W. [Institut fuer Mineralogie-Umweltanalytik, J.W. Goethe-Universitaet, Georg-Voigt-Str. 14, D-60054 a.M. Frankfurt (Germany)

2002-06-01

In the Oberdorf trough at the northwestern margin of the Styrian Basin (Austria), an up to 36-m thick Lower Miocene (Ottnangian) lignite seam occurs within the fluvial Koeflach-Voitsberg Formation. Previous results indicate that the lignite originated in a topogenous mire within a wet-forest swamp palaeoenvironment. Differences in soluble organic matter (SOM) yield of borehole samples from the lignite seam are related to free lipids present in plant waxes or resins and the presence of thermally labile polymers indicated by the contents of liptinite macerals (i.e., resinite, suberinite, and liptodetrinite). The n-alkane distribution patterns are dominated by high-molecular weight lipids with marked odd over even predominance, originating from plant waxes. A contribution of algae to the even numbered short-chain lipids, observed in considerable amounts in the footwall sediments is proposed. Terpenoid biomarkers characteristic for conifers and angiosperms were detected, consistent with palynomorphic spectra which are dominated by forest swamp pollen (Taxodiaceae-Cupressaceae) and pollen from plants living in a mixed mesophytic forest. Excellent relationships between higher plant biomarker composition and palynologic data indicate that the organic geochemical results reflect the varying inputs of coniferales vs. angiosperms. The data further imply that cuparene may be used for taxonomical differentiation of coniferales families. Organic geochemical data provide evidence that the content of land plant-derived biomarkers is controlled by the input of resin-rich conifers. Concentrations of hopanoids, dominated by hop-17(21)-ene, generally increase towards the top of the lignite, a section characterised by high extents of aromatisation of triterpenoid biomarkers. The results suggest that the aromatisation of angiosperm-derived biomarkers may be governed by the activity of anaerobic rather than by aerobic bacteria. However, changes in the depositional environment and

Production of metallurgical cokes from some Turkish lignites using sulphite liquor binders

Energy Technology Data Exchange (ETDEWEB)

Yanik, J.; Saglam, M.; Yuksel, M. (Ege University, Izmir (Turkey). Dept. of Chemistry)

1990-04-01

Soma and Tuncbilek lignites were briquetted at 80{degree}C under 0-100 MPa, using varying amounts of sulphite liquor binders. The briquettes were then carbonized at 950{degree}C, and the resulting formed cokes were examined. The effects of the type and concentration of binders, and of the briquetting pressure, on the strength and porosity of the formcokes were investigated. As a result of these experiments, optimal briquetting conditions were established. It was also stated that formcokes made from both Turkish lignite samples under optimal briquetting conditions could be used for metallurgical purposes, particularly in non-ferrous metallurgy. 17 refs., 1 fig., 4 tabs.

Thermogravimetric investigation of the co-combustion between the pyrolysis oil distillation residue and lignite.

Science.gov (United States)

Li, Hao; Xia, Shuqian; Ma, Peisheng

2016-10-01

Co-combustion of lignite with distillation residue derived from rice straw pyrolysis oil was investigated by non-isothermal thermogravimetric analysis (TGA). The addition of distillation residue improved the reactivity and combustion efficiency of lignite, such as increasing the weight loss rate at peak temperature and decreasing the burnout temperature and the total burnout. With increasing distillation residue content in the blended fuels, the synergistic interactions between distillation residue and lignite firstly increased and then decreased during co-combustion stage. Results of XRF, FTIR, (13)C NMR and SEM analysis indicated that chemical structure, mineral components and morphology of samples have great influence on the synergistic interactions. The combustion mechanisms and kinetic parameters were calculated by the Coats Redfern model, suggesting that the lowest apparent activation energy (120.19kJ/mol) for the blended fuels was obtained by blending 60wt.% distillation residue during main co-combustion stage. Copyright © 2016 Elsevier Ltd. All rights reserved.

H-binding of size- and polarity-fractionated soil and lignite humic acids after removal of metal and ash components

Science.gov (United States)

Drosos, Marios; Leenheer, Jerry A.; Avgeropoulos, Apostolos; Deligiannakis, Yiannis

2014-01-01

A fractionation technique, combining dialysis removal of metal and ash components with hydrofluoric acid and pH 10 citrate buffer followed by chromatography of dialysis permeate on XAD-8 resin at decreasing pH values, has been applied to lignite humic acid (lignite-HA) and soil humic acid (soil-HA). H-binding data and non ideal competitive adsorption-Donnan model parameters were obtained for the HA fractions by theoretical analysis of H-binding data which reveal a significant increase of the carboxyl and the phenolic charge for the lignite-HA fractions vs. the parental lignite humic acid (LParentalHA). The fractionated lignite-HA material consisted mainly of permeate fractions, some of which were fulvic acid-like. The fractionated soil-HA material consisted mainly of large macromolecular structures that did not permeate the dialysis membrane during deashing. Chargeable groups had comparable concentrations in soil-HA fractions and parental soil humic acid (SParentalHA), indicating minimal interference of ash components with carboxyl and phenolic (and/or enolic) groups. Fractionation of HA, combined with theoretical analysis of H-binding, can distinguish the supramolecular vs. macromolecular nature of fractions within the same parental HA.

Exploring the impact of reduced hydro capacity and lignite resources on the Macedonian power sector development

Directory of Open Access Journals (Sweden)

Taseska-Gjorgievskaa Verica

2014-01-01

Full Text Available The reference development pathway of the Macedonian energy sector highlights the important role that lignite and hydro power play in the power sector, each accounting for 40% of total capacity in 2021. In 2030, this dominance continues, although hydro has a higher share due to the retirement of some of the existing lignite plants. Three sensitivity runs of the MARKAL-Macedonia energy system model have been undertaken to explore the importance of these technologies to the system, considering that their resource may be reduced with time: (1 Reducing the availability of lignite from domestic mines by 50% in 2030 (with limited capacity of imports, (2 Removing three large hydro options, which account for 310 MW in the business-as-usual case, and (3 Both of the above restrictions. The reduction in lignite availability is estimated to lead to additional overall system costs of 0.7%, compared to hydro restrictions at only 0.1%. With both restrictions applied, the additional costs rise to over 1%, amounting to 348 M€ over the 25 year planning horizon. In particular, costs are driven up by an increasing reliance on electricity imports. In all cases, the total electricity generation decreases, but import increases, which leads to a drop in capacity requirements. In both, the lignite and the hydro restricted cases, it is primarily gas-fired generation and imports that “fill the gap”. This highlights the importance of an increasingly diversified and efficient supply, which should be promoted through initiatives on renewables, energy efficiency, and lower carbon emissions.

Production scheduling of a lignite mine under quality and reserves uncertainty

International Nuclear Information System (INIS)

Galetakis, Michael; Roumpos, Christos; Alevizos, George; Vamvuka, Despina

2011-01-01

The effect of uncertainty sources to the stochastic optimization of the combined project of a new surface lignite mine exploitation and power plant operation for electricity generation is investigated. Major sources of uncertainty that were considered are the reserves and the quality of the lignite. Since probability distribution functions for these uncertainties were estimated during the detailed exploration phase of the deposit, the overall goal is then to determine the optimal capacity of the power plant and consequently the optimal production rate of the mine over the time. The optimization objective that was selected is the maximization of the net present value of the project. Emphasis is placed on the sensitivity analysis for the investigation of the effect of quality and reserves uncertainty on project optimization, on the mathematical formulation of risk attitude strategy and on increasing the efficiency of the optimization process by creating a limited set of feasible solutions applying empirical rules. The developed methodology was applied for the determination of the optimal annual production rate of a new surface lignite mine in the area of Ptolemais–Amynteon in Northern Greece. - Highlights: ► Quality and reserves uncertainty affects considerably the production scheduling. ► Stochastic optimization is greatly accelerated by incorporating Taylor's rule. ► Decisions can be made considering different risk level attitudes.

Advanced power assessment for Czech lignite. Task 3.6, Volume 1

Energy Technology Data Exchange (ETDEWEB)

Sondreal, E.A.; Mann, M.D.; Weber, G.W.; Young, B.C.

1995-12-01

The US has invested heavily in research, development, and demonstration of efficient and environmentally acceptable technologies for the use of coal. The US has the opportunity to use its leadership position to market a range of advanced coal-based technologies internationally. For example, coal mining output in the Czech Republic has been decreasing. This decrease in demand can be attributed mainly to the changing structure of the Czech economy and to environmental constraints. The continued production of energy from indigenous brown coals is a major concern for the Czech Republic. The strong desire to continue to use this resource is a challenge. The Energy and Environmental Research Center undertook two major efforts recently. One effort involved an assessment of opportunities for commercialization of US coal technologies in the Czech Republic. This report is the result of that effort. The technology assessment focused on the utilization of Czech brown coals. These coals are high in ash and sulfur, and the information presented in this report focuses on the utilization of these brown coals in an economically and environmentally friendly manner. Sections 3--5 present options for utilizing the as-mined coal, while Sections 6 and 7 present options for upgrading and generating alternative uses for the lignite. Contents include Czech Republic national energy perspectives; powering; emissions control; advanced power generation systems; assessment of lignite-upgrading technologies; and alternative markets for lignite.

Determination of optimal environmental policy for reclamation of land unearthed in lignite mines - Strategy and tactics

Science.gov (United States)

Batzias, Dimitris F.; Pollalis, Yannis A.

2012-12-01

In this paper, optimal environmental policy for reclamation of land unearthed in lignite mines is defined as a strategic target. The tactics concerning the achievement of this target, includes estimation of optimal time lag between each lignite site (which is a segment of the whole lignite field) complete exploitation and its reclamation. Subsidizing of reclamation has been determined as a function of this time lag and relevant implementation is presented for parameter values valid for the Greek economy. We proved that the methodology we have developed gives reasonable quantitative results within the norms imposed by legislation. Moreover, the interconnection between strategy and tactics becomes evident, since the former causes the latter by deduction and the latter revises the former by induction in the time course of land reclamation.

Carbonate and lignite cycles in the Ptolemais Basin: Orbital control and suborbital variability (Late Neogene, northern Greece)

Science.gov (United States)

Weber, M. E.; Tougiannidis, N.; Ricken, W.; Rolf, C.; Kleineder, M.; Bertram, N.; Antoniadis, P.

2009-04-01

We recently commenced a project to investigate deep drillings as well as outcrops in the Ptolemais Basin, northern Greece, for paleoenvironmental and paleoclimate change. Specific attention is paid to mining sites Achlada, Vevi, Vegora, Amynteon, North Field, South Field, and Lava. The sediment archive comprises Upper Miocene to Quaternary continental lake deposits (up to 800 m thick) with an extended Lower Pliocene section. The Upper Miocene sections are composed of diatomaceous mud and gray marls. Pliocene lake sediments commence with the Kyrio member (lignite/grey marl), followed by the Theodoxus member (beige marl/lignite), and the Notio member (marl with intercalated sand /lignite). The limnic deposits show striking rhythmic bedding of (mostly) carbonates and lignites, reflecting orbital-induced humidity and temperature changes in this small NW-SE elongated continental basin. First, we retrieved chronometric information by determining magnetic polarity changes on three sites as independent stratigraphic ground-truth in combination with palynological evidence and published data. Then we conducted a number of high-resolution (1 - 6 cm increment), non-destructive measurements to obtain paleoclimate proxies: photospectrometry (colors L, a, b), magnetic susceptibility, and natural gamma. Accordingly, we achieved a multi-proxy insight into paleoclimate and paleoenvironmental evolution at unprecedented temporal resolution (up to a few decades!) over long time series and at a number of key sites. Using the newly-developed ESALab software, we conducted spectral and evolutionary spectral analysis to evaluate the cyclo-stratigraphic development. As for orbital variability, spectral power is concentrated on precession, hemi-precession, and eccentricity, with only minor impact of orbital tilt. We used this information to increase the temporal resolution of our age models by tuning as many precession (insolation) maxima as possible to carbonate minima (lignite maxima

Securing the future of the Lusatian lignite mining; Zukunftssicherung im Lausitzer Revier

Energy Technology Data Exchange (ETDEWEB)

Klocek, Gert [Vattenfall Europe Mining AG, Cottbus (Germany). Bergbauplanung; Ketzmer, Wolfgang [Vattenfall Europe Mining AG, Cottbus (Germany). Grunddaten und Bergtechnik

2014-11-01

In the course of securing the future of the Lusatian lignite mining, the company has initiated several measures and activities. Thus with large-scale projects such as relocating the operating and surface facilities of the Welzow-Sued opencast mine uninterrupted long-term mining advance is ensured. The company's lignite-fired power plants with their project ''FlexGen'', to further increased flexibility, enhances their position to master of the challenges of ''Energiewende''. The political and societal framework for this complex development is in line with the climate and energy programmes or strategies of the Free State of Saxony and the federal state of Brandenburg.

Mercury Control for Plants Firing Texas Lignite and Equipped with ESP-wet FGD

Energy Technology Data Exchange (ETDEWEB)

Katherine Dombrowski

2009-12-31

This report presents the results of a multi-year test program conducted as part of Cooperative Agreement DE-FC26-06NT42779, 'Mercury Control for Plants Firing Texas Lignite and Equipped with ESP-wet FGD.' The objective of this program was to determine the level of mercury removal achievable using sorbent injection for a plant firing Texas lignite fuel and equipped with an ESP and wet FGD. The project was primarily funded by the U.S. DOE National Energy Technology Laboratory. EPRI, NRG Texas, Luminant (formerly TXU), and AEP were project co-funders. URS Group was the prime contractor, and Apogee Scientific and ADA-ES were subcontractors. The host site for this program was NRG Texas Limestone Electric Generating Station (LMS) Units 1 and 2, located in Jewett, Texas. The plant fires a blend of Texas lignite and Powder River Basin (PRB) coal. Full-scale tests were conducted to evaluate the mercury removal performance of powdered sorbents injected into the flue gas upstream of the ESP (traditional configuration), upstream of the air preheater, and/or between electric fields within the ESP (Toxecon{trademark} II configuration). Phases I through III of the test program, conducted on Unit 1 in 2006-2007, consisted of three short-term parametric test phases followed by a 60-day continuous operation test. Selected mercury sorbents were injected to treat one quarter of the flue gas (e.g., approximately 225 MW equivalence) produced by Limestone Unit 1. Six sorbents and three injection configurations were evaluated and results were used to select the best combination of sorbent (Norit Americas DARCO Hg-LH at 2 lb/Macf) and injection location (upstream of the ESP) for a two-month performance evaluation. A mercury removal rate of 50-70% was targeted for the long-term test. During this continuous-injection test, mercury removal performance and variability were evaluated as the plant operated under normal conditions. Additional evaluations were made to determine any

JV Task - 129 Advanced Conversion Test - Bulgarian Lignite

Energy Technology Data Exchange (ETDEWEB)

Michael Swanson; Everett Sondreal; Daniel Laudal; Douglas Hajicek; Ann Henderson; Brandon Pavlish

2009-03-27

The objectives of this Energy & Environmental Research Center (EERC) project were to evaluate Bulgarian lignite performance under both fluid-bed combustion and gasification conditions and provide a recommendation as to which technology would be the most technically feasible for the particular feedstock and also identify any potential operating issues (such as bed agglomeration, etc.) that may limit the applicability of a potential coal conversion technology. Gasification tests were run at the EERC in the 100-400-kg/hr transport reactor development unit (TRDU) on a 50-tonne sample of lignite supplied by the Bulgarian Lignite Power Project. The quality of the test sample was inferior to any coal previously tested in this unit, containing 50% ash at 26.7% moisture and having a higher heating value of 5043 kJ/kg after partial drying in preparation for testing. The tentative conclusion reached on the basis of tests in the TRDU is that oxygen-blown gasification of this high-ash Bulgarian lignite sample using the Kellogg, Brown, and Root (KBR) transport gasifier technology would not provide a syngas suitable for directly firing a gas turbine. After correcting for test conditions specific to the pilot-scale TRDU, including an unavoidably high heat loss and nitrogen dilution by transport air, the best-case heating value for oxygen-blown operation was estimated to be 3316 kJ/m{sup 3} for a commercial KRB transport gasifier. This heating value is about 80% of the minimum required for firing a gas turbine. Removing 50% of the carbon dioxide from the syngas would increase the heating value to 4583 kJ/m{sup 3}, i.e., to about 110% of the minimum requirement, and 95% removal would provide a heating value of 7080 kJ/m{sup 3}. Supplemental firing of natural gas would also allow the integrated gasification combined cycle (IGCC) technology to be utilized without having to remove CO{sub 2}. If removal of all nitrogen from the input gas streams such as the coal transport air were

Techno-economic analysis of lignite fuelled IGCC with CO{sub 2} capture. Comparing fluidized bed and entrained flow gasifiers

Energy Technology Data Exchange (ETDEWEB)

Liu, Guangjian; Wu, Zhen; Zhang, Haiying [North China Electric Power Univ., Beijing (China). School of Energy and Power Engineering

2013-07-01

Integrated coal gasification combined cycle (IGCC) plants with pre-combustion capture of CO{sub 2} represent one of the most promising options for generating low-cost decarbonized power using bituminous coals. This work systematically quantify the effect of coal rank on the efficiency and economics of IGCC systems with CO2 capture and storage (CCS), with a special focus on comparison of systems using fluidized-bed gasifier (U-GAS) and entrained flow gasifier (Shell). It was found that the Shell IGCCs are little affect by low rank coal after pre-drying in terms of thermal efficiency and the levelized cost of electricity (LCOE) is only increase by 2-6% for lignite cases with and without CCS compared with bituminous coal cases. The specific CO{sub 2} emissions of U-GAS gasifier based lignite fuelled IGCC with CCS is 198 g/kWhe, almost two times of shell gasifier cases, mainly due to lower carbon conversion in the gasifier and the higher methane in the raw gas of gasifier. However, the total capital cost and COE of U-Gas IGCCs are 15-20% less than that of Shell IGCCs because of lower capital cost of gasifier, coal drying units and air separate units per kWe.

Dry re-forming of methane to synthesis gas over lignite semicokes catalyst at high pressure

Directory of Open Access Journals (Sweden)

Fengbo Guo

2016-11-01

Full Text Available Dry re-forming of methane has been carried out in a high temperature–pressure reactor at different pressures, using Hongce lignite semicokes catalyst. The results show that CH4 and CO2 conversions are decreased as the reaction pressure increased, but both of them kept basically stable when the reaction pressure is between 0.3 and 1 MPa. The comparison shows that the effects of the temperature and the flow of reactant gas on dry re-forming of methane are consistent with between high pressure and atmospheric pressure. The ratio of CO/H2 decreased as the ratio of CH4/CO2 increased, yet the value of CO/H2 is always more than 1 at different pressures. Hongce lignite semicokes catalyst is characterized by FTIR, XRD, SEM and BET, and the analysis results reveled that the physical specific adsorption peak of CO2 at 2350 cm−1 is strengthened significantly at different pressures, the micropore area and volume of Hongce lignite semicokes reduced form 40.2 m2  g−1 and 0.019 cm3  g−1 to 34.9 m2  g−1 and 0.017 cm3  g−1, respectively. Hongce lignite semicokes catalyst exhibited better activity and stability within 0.3–1 MPa range.

Activated-Lignite-Based Super Large Granular Slow-Release Fertilizers Improve Apple Tree Growth: Synthesis, Characterizations, and Laboratory and Field Evaluations.

Science.gov (United States)

Tang, Yafu; Wang, Xinying; Yang, Yuechao; Gao, Bin; Wan, Yongshan; Li, Yuncong C; Cheng, Dongdong

2017-07-26

In this work, lignite, a low-grade coal, was modified using the solid-phase activation method with the aid of a Pd/CeO 2 nanoparticle catalyst to improve its pore structure and nutrient absorption. Results indicate that the adsorption ability of the activated lignite to NO 3 - , NH 4 + , H 2 PO 4 - , and K + was significantly higher than that of raw lignite. The activated lignite was successfully combined with the polymeric slow-release fertilizer, which exhibits typical slow-release behavior, to prepare the super large granular activated lignite slow-release fertilizer (SAF). In addition to the slow-release ability, the SAF showed excellent water-retention capabilities. Soil column leaching experiments further confirmed the slow-release characteristics of the SAF with fertilizer nutrient loss greatly reduced in comparison to traditional and slow-release fertilizers. Furthermore, field tests of the SAF in an orchard showed that the novel SAF was better than other tested fertilizers in improve the growth of young apple trees. Findings from this study suggest that the newly developed SAF has great potential to be used in apple cultivation and production systems in the future.

Genetic relationship of organic bases of the quinoline and isoquinoline series from lignite semicoking tars with the initial biological material

Energy Technology Data Exchange (ETDEWEB)

Platonov, V.V.; Proskuryakov, V.A.; Podshibyakin, S.I.; Domogatskii, V.V.; Shvykin, A.Y.; Shavyrina, O.A.; Chilachava, K.B. [Leo Tolstoy State Pedagog University, Tula (Russian Federation)

2002-07-01

The genetic relationship of quinoline and isoquinoline compounds present in semicoking tars of Kimovsk lignites (near-Moscow fields) with the initial vegetable material is discussed. Transformation pathways of the native compounds in the course of lignite formation are suggested.

Synthetic fuel production using Texas lignite and a very high temperature reactor for process heat

International Nuclear Information System (INIS)

Ross, M.A.; Klein, D.E.

1982-01-01

Two approaches for synthetic fuel production from coal are studied using Texas lignite as the feedstock. First, the gasification and liquefaction of coal are accomplished using Lurgi gasifiers and Fischer-Tropsch synthesis. A 50 000 barrel/day facility, consuming 13.7 million tonne/yr (15.1 million ton/yr) of lignite, is considered. Second, a nuclear-assisted coal conversion approach is studied using a very high temperature gas-cooled reactor with a modified Lurgi gasifier and Fischer-Tropsch synthesis. The nuclear-assisted approach resulted in a 35% reduction in coal consumption. In addition, process steam consumption was reduced by one-half and the oxygen plants were eliminated in the nuclear assisted process. Both approaches resulted in a synthetic oil price higher than the March 1980 imported price of $29.65 per barrel: $36.15 for the lignite-only process and $35.16 for the nuclear-assisted process. No tax advantage was assumed for either process and the utility financing method was used for both economic calculations

Operational experience of a 300-MW lignite-fired utility unit: environmental performance after retrofiitting of a low pressure turbine

Energy Technology Data Exchange (ETDEWEB)

Tanetsakunvatana, Vicharn; Arkornsakul, P.

2010-09-15

The experimental data on major emissions from a 300-MW lignite-fired boiler operating under different fuel LHVs and turbine rotors are discussed. The thermal efficiency was quantified based on the heat loss method. The PM and CO2 emission rates were predicted. Specific emissions were quantified for the boiler of interest. The SO2, PM and NOx emission concentrations in flue gas were found lower than the respective emission standard. The CO2 emissions have also declined 4.65% in 2009, compared to 2008 and before. The clean development mechanism complied with UNFCCC methodology is adopted in this study responding to the global changes.

Application of process simulation for evaluation of ecologically benefical developments in thermal power plant technology

International Nuclear Information System (INIS)

Schuster, G.

2000-04-01

Responsibility for the environment and a sustainable utilization of resources gain also in the production of electric power more and more importance. For this reason existing power generation processes have to be improved and alternatives to existing processes have to be developed. As a first step in this procedure process simulation is a powerful tool to evaluate the potentials of new developments. In this work it is shown, how new thermal power processes are modeled and simulated based on well-known thermodynamic and chemical correlations. Processes for thermal power plants using lignite with high water content and biomass as fuel are studied. In each case simulations are carried out for complete plants including all important unit operations. Based on a conventional thermal power plant for lignite different variants for efficiency improvement by fuel drying are examined. Additionally the potential of a process with gasification and gas turbine is discussed. Compared to a lignite power plant the preconditions for a biomass power plant are different. A promising option for the future seems to be small, decentralized combined heat and power plants. Therefore a process with simple and compact design including gasifier and gas turbine is regarded and sensitivity analyses are carried out. As well as for the lignite processes possible improvements by fuel drying are studied. The basis lignite power plant (drying in an impact rotor mill with hot flue gas) has an overall electric efficiency of 36 %. Alternative fuel drying processes (reducing water content from 54 w % to 10 w %) can increase efficiency to nearly 43 %. Using integrated air-blown gasification combined with gas turbine and steam turbine and additional fuel drying raises the efficiency up to 49 % in the case of cold gas cleanup and up to 50 percent in the case of hot gas cleanup. Efficiencies of the regarded biomass power plants are in the range of about 20 % (with a biomass water content of 25 w %). By

JV TASK 45-MERCURY CONTROL TECHNOLOGIES FOR ELECTRIC UTILITIES BURNING LIGNITE COAL, PHASE I BENCH-AND PILOT-SCALE TESTING

Energy Technology Data Exchange (ETDEWEB)

John H. Pavlish; Michael J. Holmes; Steven A. Benson; Charlene R. Crocker; Edwin S. Olson; Kevin C. Galbreath; Ye Zhuang; Brandon M. Pavlish

2003-10-01

The Energy & Environmental Research Center has completed the first phase of a 3-year, two-phase consortium project to develop and demonstrate mercury control technologies for utilities that burn lignite coal. The overall project goal is to maintain the viability of lignite-based energy production by providing utilities with low-cost options for meeting future mercury regulations. Phase I objectives are to develop a better understanding of mercury interactions with flue gas constituents, test a range of sorbent-based technologies targeted at removing elemental mercury (Hg{sup o}) from flue gases, and demonstrate the effectiveness of the most promising technologies at the pilot scale. The Phase II objectives are to demonstrate and quantify sorbent technology effectiveness, performance, and cost at a sponsor-owned and operated power plant. Phase I results are presented in this report along with a brief overview of the Phase II plans. Bench-scale testing provided information on mercury interactions with flue gas constituents and relative performances of the various sorbents. Activated carbons were prepared from relatively high-sodium lignites by carbonization at 400 C (752 F), followed by steam activation at 750 C (1382 F) and 800 C (1472 F). Luscar char was also steam-activated at these conditions. These lignite-based activated carbons, along with commercially available DARCO FGD and an oxidized calcium silicate, were tested in a thin-film, fixed-bed, bench-scale reactor using a simulated lignitic flue gas consisting of 10 {micro}g/Nm{sup 3} Hg{sup 0}, 6% O{sub 2}, 12% CO{sub 2}, 15% H{sub 2}O, 580 ppm SO{sub 2}, 120 ppm NO, 6 ppm NO{sub 2}, and 1 ppm HCl in N{sub 2}. All of the lignite-based activated (750 C, 1382 F) carbons required a 30-45-minute conditioning period in the simulated lignite flue gas before they exhibited good mercury sorption capacities. The unactivated Luscar char and oxidized calcium silicate were ineffective in capturing mercury. Lignite

Local community opinions regarding the socio-environmental aspects of lignite surface mining: Experiences from central Poland

International Nuclear Information System (INIS)

Badera, Jarosław; Kocoń, Paweł

2014-01-01

Surface lignite mining covers large areas and usually generates social conflicts which pose one of several energy security threats to certain states. Therefore, defining the social conditions determines the success of a mining project. Two communes were chosen for a public opinion study: Kleszczów, where the Bełchatów mine is located, and Złoczew, where a lignite deposit will soon be developed. The analysis shows, as opposed to other areas in Poland that have been projected for development, that both local communities are characterised by a high level of acceptance for lignite mining. In both cases, awareness about the profits was stronger than anxiety about the investment's negative effects. However, most inhabitants could not assess the mining company's diligence concerning its responsibility for mining damages as well as the diligence of external experts assessing the environmental impacts of excavation. Most respondents also could not assess if the legal regulations of public participation in the decision process were sufficient, but the negative opinions outweighed the positive ones. From the perspective of the energy policy, dialogue-type social communication is needed for every case of a new energy-mining project. Research on local public opinion should be the first step to opening up a social debate. - Highlights: • Lignite mining can generate social conflicts, which may threaten energy security. • Examined communes are characterised by a high level of acceptance for lignite mining. • Inhabitants cannot assess if the legal regulations of mining activity are sufficient. • From the perspective of the energy policy, broader social communication is needed. • Research on the public opinion should be the first step to open up a social debate

Lusatian lignite. Decisions for the future; Lausitzer Braunkohle. Entscheidungen fuer die Zukunft

Energy Technology Data Exchange (ETDEWEB)

Daehnert, Detlev [Vattenfall Europe Mining AG, Cottbus (Germany); Vattenfall Europe Generation AG und Co. KG, Cottbus (Germany); Ketzmer, Wolfgang [Vattenfall Europe Generation AG und Co. KG, Cottbus (Germany)

2008-07-15

During the past months a number of important decisions regarding the future of the Lusatian lignite mining areas have been made or launched. In the focus is the concept of the long-term opencast mine and power plant development. Essential part of the concept is the strategy for meeting future challenges of climate change policy. CCS is the key for it. It is expected, that the CCS technology will be commercially available after 2020. Another important aspect is among others the use of the priority areas of the Welzow-Sued and Nochten opencast mined. The corresponding long-term lignite mining planning procedures were opened in autumn 2007. The plans of the company contain clear and reliable statements regarding the long-term opencast mine development until 2050. However, all decisions the company makes are focussing on putting people and their needs first. Solutions for mining related questions and requirements are jointly developed with the people of the region. Communities in direct neighbourhood to opencast mines are safely protected against immissions by structural and organisational measures. The principles of socially responsible resettlements set the framework of constructive and trustful co-acting of the people concerned and the company very early. The future post-mining landscape offers alternative utilization forms providing employment for many people. Economic development of the region is an important aspect of the company's activities. Under the headline ''Energy region Lusatia'', representatives of Vattenfall, different educational institutions, authorities and the politics have joined forces to formulate a strategic target for the future development of Lusatia. Sustainable development of lignite-based power generation to meet future climate change policy, development of energy industrial know-how and the use of other fuels are important issues. The results are visible. Lignite takes a solid place in the German Energy mix - it

Sorption of heavy metals on lignite impregnated with chitosan

Czech Academy of Sciences Publication Activity Database

Havelcová, Martina; Mizera, Jiří; Machovič, V.; Borecká, Lenka; Přibyl, Oldřich; Krausová, Ivana

2013-01-01

Roč. 10, č. 1 (2013), s. 105-110 ISSN 1214-9705 R&D Projects: GA ČR(CZ) GBP108/12/G108 Institutional support: RVO:67985891 ; RVO:61389005 Keywords : lignite * chitosan * heavy metals * sorption Subject RIV: DJ - Water Pollution ; Quality Impact factor: 0.667, year: 2013 http://www.irsm.cas.cz/index_en.php?page=acta_detail_doi&id=19

Radon measurements concerning engineering-geological problems in lignite mining

Energy Technology Data Exchange (ETDEWEB)

Heinicke, J

1986-07-01

Radon measurements have been carried out by the aid of solid-state track detectors at the highwall of a lignite mine in order to forecast the eventual course of a landslide. The measured radon distributions and their changes as a function of time indicated that the slope was geodynamically active, but it was not possible to forecast the rate of sliding.

Treating high-mercury-containing lamps using full-scale thermal desorption technology.

Science.gov (United States)

Chang, T C; You, S J; Yu, B S; Chen, C M; Chiu, Y C

2009-03-15

The mercury content in high-mercury-containing lamps are always between 400 mg/kg and 200,000 mg/kg. This concentration is much higher than the 260 mg/kg lower boundary recommended for the thermal desorption process suggested by the US Resource Conservation and Recovery Act. According to a Taiwan EPA survey, about 4,833,000 cold cathode fluorescent lamps (CCFLs), 486,000 ultraviolet lamps and 25,000 super high pressure mercury lamps (SHPs) have been disposed of in the industrial waste treatment system, producing 80, 92 and 9 kg-mercury/year through domestic treatment, offshore treatment and air emissions, respectively. To deal with this problem we set up a full-scale thermal desorption process to treat and recover the mercury from SHPs, fluorescent tube tailpipes, fluorescent tubes containing mercury-fluorescent powder, and CCFLs containing mercury-fluorescent powder and monitor the use of different pre-heating temperatures and desorption times. The experimental results reveal that the average thermal desorption efficiency of SHPs and fluorescent tube tailpipe were both 99.95%, while the average thermal desorption efficiencies of fluorescent tubes containing mercury-fluorescent powder were between 97% and 99%. In addition, a thermal desorption efficiency of only 69.37-93.39% was obtained after treating the CCFLs containing mercury-fluorescent powder. These differences in thermal desorption efficiency might be due to the complexity of the mercury compounds contained in the lamps. In general, the thermal desorption efficiency of lamps containing mercury-complex compounds increased with higher temperatures.

Briquetting of Tuncbilek lignite fines by using ammonium nitrohumate as a binder

Energy Technology Data Exchange (ETDEWEB)

Yildirim, M.; Ozbayoglu, G. [Cukurova University, Adana (Turkey). Mining Engineering Dept.

2004-03-01

Results of experiments on the briquetting of Tuncbilek lignite fines using ammonium nitrohumate (anh), a low calorific value, young lignite-derived humic acid salt solution, are reported. The particulate material was blended with ammonium nitrohumate serving as the binder. In the briquetting tests, the effects of moisture content, pressure, binder content, nitrogen content and heat treatment were investigated. Durable briquettes, in terms of mechanical strength and water resistance, were produced with a 7% binder content at 10.5% moisture, following pressing at 1280 kg/cm{sup 2} and drying at 165{sup o}C for 1 h. The briqueues produced with ammonium nitrohumate had better combustion properties than run-of-mine samples; the contribution of the binder to smoke and sulphur emissions was very low and fine dust particles were negligible.

REMOVAL OF TRICHLOROACETIC ACID FROM THE AQUEOUS SOLUTIONS USING NATURAL AND ACTIVATED LIGNITE COALS

Directory of Open Access Journals (Sweden)

Hüseyin GÜLENSOY

1998-02-01

Full Text Available In these studies, a typical lignite coal found near Istanbul (Yeniköy and its activated products were used to adsorb TCA from aqueous solutions. Particle sizes of coal samples and the concentrations of TCA solutions were chosen as parameters against the fixed amount of adsorbent. The maximum efficiency has been obtained for the coal having (-120 + 150 mesh size fraction activated by heating. As a result, it was shown that these kinds of lignite coals could be used as a good adsorbent. In addition, it was also proved that both the removal and recovery of TCA from some waste waters would easily be possible.

Preparation and combustion of Yugoslavian lignite-water fuel, Task 7.35. Topical report, July 1991--December 1993

Energy Technology Data Exchange (ETDEWEB)

Anderson, C.M.; DeWall, R.A.; Ljubicic, B.R.; Musich, M.A.; Richter, J.J.

1994-03-01

Yugoslavia`s interest in lignite-water fuel (LWF) stems from its involvement in an unusual power project at Kovin in northern Serbia. In the early 1980s, Electric Power of Serbia (EPS) proposed constructing a 600-MW power plant that would be fueled by lignite found in deposits along and under the Danube River. Trial underwater mining at Kovin proved that the dredging operation is feasible. The dredging method produces a coal slurry containing 85% to 90% water. Plans included draining the water from the coal, drying it, and then burning it in the pulverized coal plant. In looking for alternative ways to utilize the ``wet coal`` in a more efficient and economical way, a consortium of Yugoslavian companies agreed to assess the conversion of dredged lignite into a LWF using hot-water-drying (HWD) technology. HWD is a high-temperature, nonevaporative drying technique carried out under high pressure in water that permanently alters the structure of low-rank coals. Changes effected by the drying process include irreversible removal of moisture, micropore sealing by tar, and enhancement of heating value by removal of oxygen, thus, enhancement of the slurry ability of the coal with water. Physical cleaning results indicated a 51 wt % reduction in ash content with a 76 wt % yield for the lignite. In addition, physical cleaning produced a cleaned slurry that had a higher attainable solids loading than a raw uncleaned coal slurry. Combustion studies were then performed on the raw and physically cleaned samples with the resulting indicating that both samples were very reactive, making them excellent candidates for HWD. Bench-scale results showed that HWD increased energy densities of the two raw lignite samples by approximately 63% and 81%. An order-of-magnitude cost estimate was conducted to evaluate the HWD and pipeline transport of Kovin LWF to domestic and export European markets. Results are described.

Thermal analysis of used and radiation treated polycarbonate (L-MW) biomaterial

International Nuclear Information System (INIS)

Jayabalan, M.; Sreenivasan, K.; Nair, P.D.; Jalajamani, K.V.

1988-01-01

γ-radiation treatment of radiation sterilized polycarbonate biomaterials has been carried out to ensure efficient disposal by incineration. Low molecular weight polycarbonate sterilized with 2.5 Mrad dose of γ-radiation was further treated with different doses of γ-radiation. The radiation-treated samples were subjected to thermogravimetry. The sterilized sample and the 7.5 Mrad-treated sample showed similar properties. These samples do not leave any residue during thermal decomposition. (author). 5 refs., 3 tables

Volatiles and char combustion rates of demineralised lignite and wood blends

International Nuclear Information System (INIS)

Yilgin, Melek; Pehlivan, Dursun

2009-01-01

Today, much interest is given to the utilisation of materials of plant origin as substitutions of fossil fuels in meeting energy needs to reduce the level of atmospheric pollutant emissions and global warming threat, and emphasis has been placed on the co-combustion of coal and biomass. In this study, volatiles and char combustion behaviour of the fuel pellets composed from demineralised lignite and poplar wood sawdust, were investigated in a cylindrical wire mesh basket placed in a preheated tube furnace. The results have shown that ignition times of the pellets decreased with the burning temperature and shortened further due to demineralisation of lignite. Volatiles combustion rates of the samples did not correlate well with combustion times. However, they can be correlated with their respective proximate volatile matter contents. Char burnout times decreased with increasing combustion rates and correlated well with the respective proximate fixed carbon contents of the samples. Deviations were more considerable in the case of rate data. (author)

The hydrogasification of lignite and sub-bituminous coals

Science.gov (United States)

Bhatt, B.; Fallon, P. T.; Steinberg, M.

1981-02-01

A North Dakota lignite and a New Mexico sub-bituminous coal have been hydrogenated at up to 900°C and 2500 psi hydrogen pressure. Yields of gaseous hydrocarbons and aromatic liquids have been studied as a function of temperature, pressure, residence time, feed rates and H2/coal ratio. Coal feed rates in excess of 10 lb/hr have been achieved in the 1 in. I. D.×8 ft reactor and methane concentration as high as 55% have been observed. A four-step reaction model was developed for the production and decomposition of the hydrocarbon products. A single object function formulated from the weighted errors for the four dependent process, variables, CH4, C2H6, BTX, and oil yields, was minimized using a program containing three independent iterative techniques. The results of the nonlinear regression analysis for lignite show that a first-order chemical reaction model with respect to C conversion satisfactorily describes the dilute phase hydrogenation. The activation energy for the initial products formation was estimated to be 42,700 cal/gmole and the power of hydrogen partial pressure was found to be +0.14. The overall correlation coefficient was 0.83. The mechanism, the rate expressions, and the design curves developed can be used for scale-up and reactor design.

Reprint of: Production scheduling of a lignite mine under quality and reserves uncertainty

International Nuclear Information System (INIS)

Galetakis, Michael; Roumpos, Christos; Alevizos, George; Vamvuka, Despina

2012-01-01

The effect of uncertainty sources to the stochastic optimization of the combined project of a new surface lignite mine exploitation and power plant operation for electricity generation is investigated. Major sources of uncertainty that were considered are the reserves and the quality of the lignite. Since probability distribution functions for these uncertainties were estimated during the detailed exploration phase of the deposit, the overall goal is then to determine the optimal capacity of the power plant and consequently the optimal production rate of the mine over the time. The optimization objective that was selected is the maximization of the net present value of the project. Emphasis is placed on the sensitivity analysis for the investigation of the effect of quality and reserves uncertainty on project optimization, on the mathematical formulation of risk attitude strategy and on increasing the efficiency of the optimization process by creating a limited set of feasible solutions applying empirical rules. The developed methodology was applied for the determination of the optimal annual production rate of a new surface lignite mine in the area of Ptolemais–Amynteon in Northern Greece. - Highlights: ► Quality and reserves uncertainty affects considerably the production scheduling. ► Stochastic optimization is greatly accelerated by incorporating Taylor's rule. ► Decisions can be made considering different risk level attitudes.

Co-gasification of a lignite/waste-tyre in a moving bed

Czech Academy of Sciences Publication Activity Database

Straka, Pavel; Bučko, Z.

2009-01-01

Roč. 90, č. 10 (2009), s. 1202-1206 ISSN 0378-3820 R&D Projects: GA ČR(CZ) GA105/07/1407 Institutional research plan: CEZ:AV0Z30460519 Keywords : co-gasification * waste-tyre * lignite Subject RIV: CD - Macromolecular Chemistry Impact factor: 2.321, year: 2009

Large-Scale Mercury Control Technology Testing for Lignite-Fired Utilities - Oxidation Systems for Wet FGD

Energy Technology Data Exchange (ETDEWEB)

Steven A. Benson; Michael J. Holmes; Donald P. McCollor; Jill M. Mackenzie; Charlene R. Crocker; Lingbu Kong; Kevin C. Galbreath

2007-03-31

Mercury (Hg) control technologies were evaluated at Minnkota Power Cooperative's Milton R. Young (MRY) Station Unit 2, a 450-MW lignite-fired cyclone unit near Center, North Dakota, and TXU Energy's Monticello Steam Electric Station (MoSES) Unit 3, a 793-MW lignite--Powder River Basin (PRB) subbituminous coal-fired unit near Mt. Pleasant, Texas. A cold-side electrostatic precipitator (ESP) and wet flue gas desulfurization (FGD) scrubber are used at MRY and MoSES for controlling particulate and sulfur dioxide (SO{sub 2}) emissions, respectively. Several approaches for significantly and cost-effectively oxidizing elemental mercury (Hg{sup 0}) in lignite combustion flue gases, followed by capture in an ESP and/or FGD scrubber were evaluated. The project team involved in performing the technical aspects of the project included Babcock & Wilcox, the Energy & Environmental Research Center (EERC), the Electric Power Research Institute, and URS Corporation. Calcium bromide (CaBr{sub 2}), calcium chloride (CaCl{sub 2}), magnesium chloride (MgCl{sub 2}), and a proprietary sorbent enhancement additive (SEA), hereafter referred to as SEA2, were added to the lignite feeds to enhance Hg capture in the ESP and/or wet FGD. In addition, powdered activated carbon (PAC) was injected upstream of the ESP at MRY Unit 2. The work involved establishing Hg concentrations and removal rates across existing ESP and FGD units, determining costs associated with a given Hg removal efficiency, quantifying the balance-of-plant impacts of the control technologies, and facilitating technology commercialization. The primary project goal was to achieve ESP-FGD Hg removal efficiencies of {ge}55% at MRY and MoSES for about a month.

Mangrove associated lignite beds of Malvan, Konkan: Evidence for higher sea-level during the Late Tertiary (Neogene) along the west coast of India

Energy Technology Data Exchange (ETDEWEB)

Kumaran, K.P.N.; Shindikar, M.; Limaye, R.B. [Agharkar Research Inst., Pune (India)

2004-01-25

Fossil pneumatophores (breathing roots) of Avicennia are recovered and reported from the lignite beds exposed in Kolamb well-section near Malvan, Konkan area of western Maharashtra. The accrued palynoflora is dominated by mangroves (Avicennia, Aegialitis, Excoecaria, Rhizophora and Sonneratia). The spores of mangrove fern (Acrostichum aureum) an estuarine fungus Cirrenalia indicate that these lignites are autochthonous and deposited in a near-shore environment. Presence of foraminiferal linings (= microforaminifera), dinoflagellate cysts, a few calcareous nannofossils and scolecodonts is an irrefutable proof of marine and brackish water influence during the deposition of lignites under intertidal/tidal swampy condition (mangrove influenced) with fair input from freshwater swamps and hinterland. Freshwater-related forms, viz. Ceratopteris thalictroides, Nymphaeaceae, Ctenolophonaceae and hinterland taxa (Cullenia/Durio) of Bombacaceae along with abundance of microthyriaceous fungi in the palynoflora imply a warm humid tropical climate with high precipitation during the depositional period. The presence of Ctenolophon englerianus (= Ctenolophonidites costatus) in Kolamb lignites suggests the Late Neogene (Late Miocene-Early Pliocene) age. The occurrence of pneumatophores and associated lignite deposits about 37 m above the present mean sea-level, and much inland, clearly indicates the higher sea-level strand during Late Neogene along the west coast of India.

Water extraction from high moisture lignite by means of efficient integration of waste heat and water recovery technologies with flue gas pre-drying system

International Nuclear Information System (INIS)

Han, Xiaoqu; Yan, Junjie; Karellas, Sotirios; Liu, Ming; Kakaras, Emmanuel; Xiao, Feng

2017-01-01

Highlights: • Energy-saving potential of FPLPS in different cold-ends and lignite types is evaluated. • Water-saving of FPLPS is realized through recovery of water extracted from lignite. • Integrations of low pressure economizer and spray tower with FPLPS are proposed. • Thermodynamic and economic performances of different schemes are investigated. - Abstract: The flue gas pre-dried lignite-fired power system (FPLPS) integrates the fan mill flue gas dryer with an open pulverizing system and yields an increase of the boiler efficiency. Particularly, the dryer exhaust gas contains a large amount of vapor removed from high moisture lignite, which exhibits great potential for waste heat and water recovery. Two available options are considered to realize the extraction of water from lignite: the low pressure economizer (LPE) for water-cooled units and the spray tower (SPT) integrated with heat pump for air-cooled units. This paper aims at evaluating the energy saving and water recovery potentials of the FPLPS integrated with both schemes. Results showed that the plant efficiency improvement of the FPLPS at base case varied from 1.14% to 1.47% depending on the moisture content of raw lignite. The water recovery ratio and plant efficiency improvement in the optimal LPE scheme were 39.4% and 0.20%, respectively. In contrast, 83.3% of water recover ratio and 110.6 MW_t_h heat supply were achieved in the SPT system. Both schemes were economically feasible with discounted payback periods of around 3 years. Moreover, parametric analysis was conducted to examine the economic viability of both schemes with different lignite types and market factors.

Palynostratigraphy, palynofacies and depositional environment of a lignite-bearing succession at Surkha Mine, Cambay Basin, north-western India

Directory of Open Access Journals (Sweden)

Monga Priyanka

2015-12-01

Full Text Available The paper reports palynology and palynofacies studies of lignite-bearing sediments exposed in an opencast mine succession at Surkha, Bhavnagar District, in the coastal region of Gujarat, India. The study examined the relationships between the palynoflora, sedimentary organic matter and environment at the time of deposition of lignite and associated sediments. Based on dinoflagellate cyst biostratigraphy, the sedimentary succession is dated as early Eocene (Ypresian. Palynofacies studies helped reveal the palaeoenvironmental fluctuations. The dominance of angiosperm pollen grains, freshwater algae, microthyraceous fungi and a large share of land debris in the lower part of the succession suggests a freshwater swamp environment of deposition for the basal lignite facies. Two cenozones - Matanomadiasulcites maximus and Lakiapollis ovatus - were identified in the lower lignite facies, determined from the dominance of these pollen grains in the palynological assemblages. The presence of angiosperm pollen grains and pteridophyte spores in the carbonaceous shale horizon above the lignite facies indicates a change in the depositional regime from freshwater swamp to lagoonal. This was identified as the Arecipites wodehousei cenozone due to its numerical abundance in the assemblage. Dinoflagellate cyst abundance and diversity, and microforaminiferal test linings along with well-sorted terrestrial debris in the mudstone in the upper part of the succession suggest a more open marine estuarine type of depositional environment. The Homotryblium complex along with Cordospheridium fibrospinosum, Kenleyia sp., and Thalassiphora pelagica dinoflagellate cysts are the main representatives of this zone, determined as the Homotryblium tenuispinosum cenozone. The changing depositional settings (freshwater swamp-lagoonal-estuarine along the vertical succession indicate a marine transgression in this region. Results from palynological studies of early Palaeogene

Australian opencast-lignite mine Yallourn; Der australische Braunkohlentagebau Yallourn

Energy Technology Data Exchange (ETDEWEB)

Koscierski, Marcin; Goerlich, Michael [RWTH Aachen (Germany). Inst. fuer Bergbaukunde I

2009-01-15

This article is about the open pit lignite mine Yallourn, located 150 km southeast of Melbourne (Figure 1). It focuses on the history, the geology and the environment. Furthermore, it describes the new mining method using large carry dozers. The open pit and the power plant are owned by TruEnergy (part of the CLP Group) and the mining activities are carried out in an Alliance with Roche Thiess Linfox (RTL). (orig.)

Physico-chemistry of adsorption of copper, nickel and cobalt on lignite from ammoniacal solutions

International Nuclear Information System (INIS)

Khattak, M.I.

2004-01-01

The present paper deals with a process developed for lignite adsorption that can be used to prevent the hard scale formation during distillation of NH/sub 3/ and CO/sub 2/, recover Cu, Ni and Cr from dilute solutions, Cu and NH/sub 3/ from waste effluent containing SO/sub 4/ radicals, separate Cu (NH/sub 3/)/sub 4//sup +2/ and AsO/sub 4//sup -3/ from ammonial solutions and recover Cu, Ni and Co from ore pulps. In additions to the study of the adsorptions of M, NH/sub 3/ and CO/sub 2/ on lignite with caustic soda) was also investigated. Changes of the functional groups of humic acid its salt, before and after the adsorption, were examined by infrared adsorption analysis. (author)

Synergetic use of lignite fly ash and metallurgical converter slag in geopolymer concrete

Directory of Open Access Journals (Sweden)

Gábor Mucsi

2014-08-01

Full Text Available The application and utilization of the industrial wastes and by-products in the construction industry is a key issue from an environmental and economic point of view. The increased use of lignite has substantially increased the available quantities of lignite fired power plant fly ash, which can be mainly classified as class C fly ash. The utilization of such raw material however has some difficulties. In the present paper lignite fired power station fly ash and metallurgical converter slag were used for the production of geopolymer concrete. The fly ash was used as a geopolymer based binder material, and a converter slag as aggregate, thus created a geopolymer concrete which contains mainly industrial wastes. As preliminary test experimental series were carried out using andesite as aggregate. The optimal aggregate/binder ratio was determined. The effect of the amount of alkaline activator solution in the binder, the aggregate type on the geopolymer concretes’ compressive strength and density was investigated. Furthermore, the physical properties - freeze-thaw resistance and particle size distribution - of the applied aggregates were measured as well. As a result of the experiments it was found that physical properties of the andesite and converter slag aggregate was close. Therefore andesite can be replaced by converter slag in the concrete mixture. Additionally, geopolymer concrete with nearly 20 MPa compressive strength was produced from class C fly ash and converter slag.

Potential climate change impacts on water availability and cooling water demand in the Lusatian Lignite Mining Region, Central Europe

Science.gov (United States)

Pohle, Ina; Koch, Hagen; Gädeke, Anne; Grünewald, Uwe; Kaltofen, Michael; Redetzky, Michael

2014-05-01

In the catchments of the rivers Schwarze Elster, Spree and Lusatian Neisse, hydrologic and socioeconomic systems are coupled via a complex water management system in which water users, reservoirs and water transfers are included. Lignite mining and electricity production are major water users in the region: To allow for open pit lignite mining, ground water is depleted and released into the river system while cooling water is used in the thermal power plants. In order to assess potential climate change impacts on water availability in the catchments as well as on the water demand of the thermal power plants, a climate change impact assessment was performed using the hydrological model SWIM and the long term water management model WBalMo. The potential impacts of climate change were considered by using three regional climate change scenarios of the statistical regional climate model STAR assuming a further temperature increase of 0, 2 or 3 K by the year 2050 in the region respectively. Furthermore, scenarios assuming decreasing mining activities in terms of a decreasing groundwater depression cone, lower mining water discharges, and reduced cooling water demand of the thermal power plants are considered. In the standard version of the WBalMo model cooling water demand is considered as static with regard to climate variables. However, changes in the future cooling water demand over time according to the plans of the local mining and power plant operator are considered. In order to account for climate change impacts on the cooling water demand of the thermal power plants, a dynamical approach for calculating water demand was implemented in WBalMo. As this approach is based on air temperature and air humidity, the projected air temperature and air humidity of the climate scenarios at the locations of the power plants are included in the calculation. Due to increasing temperature and decreasing precipitation declining natural and managed discharges, and hence a lower

State and performance of on-stream ash content determination in lignite and black coal using 2-energy transmission technique

International Nuclear Information System (INIS)

Thuemmel, H.W.; Koerner, G.; Leonhardt, J.

1986-01-01

The total r.m.s. ash error of the 2-energy transmission on-stream ash gauges KRAS-2 (CIIRR, GDR) and SIROASH (Australia) are 4 weight percentage for raw lignite and 0.5 weight percentage for black coal, respectively. A detailed error analysis shows that this difference is due to the high water content and to strong variations in the ash composition of raw lignite. Both gauges show essentially the same radiometric performance. (author)

Lignite and tin ores exploration in southern part of Thailand by using nuclear track-etch detectors

International Nuclear Information System (INIS)

Chittrakarn, T.; Boonnummar, R.; Pongsuwan, T.; Nuannin, P.; Kaew-On, C.

1993-01-01

Both lignite and tin mines in Southern of Thailand are associated with uranium ore. In lignite exploration, Bangpudum Lignite Mine at Krabi Province was chosen for this studied because we know the exact location and deposition of coal seam by using other geophysical technique and also confirm by borehole. The size 1x2 cm 2 of cellulose nitrate CN-85 films were used, each film was stuck at the inner bottom of a softdrink cup. Each cup was put up side down at the bottom of a borehole about 75 cm depth from the earth surface and laid about 10 m apart. All the cups were put in the hole along the line in order to cover about 280 metre in the cross sectional direction long of the known coal seam. After one month, all the film detectors were collected and etched with 6.25N NaOH at 60 o C about 25 minutes long in order to enlarge the latent alpha registration tracks. These alpha particles were emitted from radon gas (Rn-222) which was generated from uranium associated with lignite ore. The registration track density per area of each CN-85 film was studied by optical microscope at 400x magnifications. We found that the track densities of the films have high correlation with the depth of the known coal seam while high and low track densities will correspond to the shallow and deep coal seam respectively. Also, track density was significantly higher than background. A similar manner of experiment was designed for tin ore exploration at Ronpibul district, Nakorn Si Thammarat province. The result is in progress and will present at the conference. (Author)

Effect of co-combustion on the burnout of lignite/biomass blends: a Turkish case study.

Science.gov (United States)

Haykiri-Acma, H; Yaman, S

2008-11-01

Co-combustion of Turkish Elbistan lignite and woody shells of hazelnut was performed in a TGA up to 1173 K with a heating rate of 20 K/min. SEM images of each fuel revealed the differences in their physical appearances. Hazelnut shell was blended with lignite in the range of 2-20 wt% to observe the co-combustion properties. Maximum burning rates (Rmax), temperatures of the maximum burning rates (T(R-max)), and the final burnout values of the parent samples and the blends were compared. The results were interpreted considering lignite properties and the major biomass ingredients such as cellulosics, hemicellulosics, and lignin. Deviations between the theoretical and experimental burnout values were evaluated at various temperatures. Burnout characteristics of the blends up to 10 wt% were concluded to have a synergistic effect so the addition of hazelnut shell up to 8 wt% provided higher burnouts than the expected theoretical ones, whereas addition of as much as 10 wt% led to a decrease in the burnout. However, the additive effects were more favorable for the blend having a biomass content of 20 wt%. Apparent activation energy, Rmax, and T(R-max), were found to follow the additive behavior for the blend samples.

Effect of co-combustion on the burnout of lignite/biomass blends: A Turkish case study

Energy Technology Data Exchange (ETDEWEB)

Haykirl-Acma, H.; Yaman, S. [Istanbul Technical University, Istanbul (Turkey)

2008-11-15

Co-combustion of Turkish Elbistan lignite and woody shells of hazelnut was performed in a TGA tip to 1173 K with a heating rate of 20 K/min. SEM images of each fuel revealed the differences in their physical appearances. Hazelnut shell was blended with lignite in the range of 2-20 wt% to observe the co-combustion properties. Maximum burning rates (R{sub max}), temperatures of the maximum burning rates (TR{sub max}), and the final burnout values of the parent samples and the blends were compared. The results were interpreted considering lignite properties and the major biomass ingredients such as cellulosics, hemicellulosics, and lignin. Deviations between the theoretical and experimental burnout values were evaluated at various temperatures. Burnout characteristics of the blends up to 10 wt% were concluded to have a synergistic effect so the addition of hazelnut shell up to 8 wt% provided higher burnouts than the expected theoretical ones, whereas addition of as much as 10 wt% led to a decrease in the burnout. However, the additive effects were more favorable for the blend having a biomass content of 20 wt%. Apparent activation energy, R{sub max} and TR{sub max}, were found to follow the additive behavior for the blend samples.

NEW DATA ON THE LOWER PLEISTOCENE (GELASIAN LIGNITE BEDS OF CASTEL SAN PIETRO (RIETI, CENTRAL ITALY

Directory of Open Access Journals (Sweden)

LUCA PANDOLFI

2017-04-01

Full Text Available A multiproxy study of the lignite-bearing lacustrine sequence cropping out at Castel San Pietro (CSP (Rieti, central Italy provides new insights on the paleoenvironmental evolution of an extensional basin, located on the Tyrrhenian side of the Apennine range. The CSP fossiliferous levels reflect deposition in a stable lacustrine environment. Mammal remains collected from this locality during the past centuries include Stephanorhinus etruscus, Anancus arvernensis and the beaver Castor fiber. The co-existence of the Etruscan rhinoceros and the mastodont suggests a middle Villafranchian age (Montopoli or Coste San Giacomo Faunal Unit for the lignite beds of CSP. New paleoflora findings are in agreement with an attribution to the Piacenzian or Gelasian age for these deposits whilst the presence of the ostracod Qinghaicypris cf. Q. riojensis suggests a time interval from Zanclean to Gelasian (between ~4.5 and ~1.8 Ma. Accordingly, the lignite beds of CSP most likely were deposited during the Gelasian (from ca. 2.5 to 1.8 Ma; from Montopoli to Coste San Giacomo FUs or possibly to Olivola FU in forested area and warm and humid conditions.

Petrography and geochemistry of selected lignite beds in the Gibbons Creek mine (Manning Formation, Jackson Group, Paleocene) of east-central Texas

Science.gov (United States)

Warwick, Peter D.; Crowley, Sharon S.; Ruppert, Leslie F.; Pontolillo, James

1997-01-01

This study examined the petrographic and geochemical characteristics of two lignite beds (3500 and 4500 beds, Manning Formation, Jackson Group, Eocene) that are mined at the Gibbons Creek mine in east-central Texas. The purpose of the study was to identify the relations among sample ash yield, coal petrography, and trace-element concentrations in lignite and adjoining rock layers of the Gibbons Creek mine. Particular interest was given to the distribution of 12 environmentally sensitive trace elements (As, Be, Cd, Cr, Co, Hg, Mn, Ni, Pb, Sb, Se, and U) that have been identified as potentially hazardous air pollutants (HAPs) in the United States Clean Air Act Amendments of 1990. Eleven lignite, floor, and rock parting samples were collected from incremental channel samples of the 3500 and 4500 beds that were exposed in a highwall of pit A3 at the Gibbons Creek mine. Short proximate and ultimate and forms of sulfur analyses were performed on all lignite samples, and lignite and rock samples were analyzed for 60 major, minor and trace elements. Representative splits of all lignite samples were ground and cast into pellets, and polished for petrographic analyses in blue-light fluorescence and reflected white light to determine liptinite, inertinite, and huminite maceral group percentages. The following observations summarize our results and conclusions about the geochemistry, petrography, and sedimentology of the 3500 and 4500 beds of the Gibbons Creek lignite deposit: (1) Weighted average dry (db) ash yield for the two beds is 29.7%, average total sulfur content is 2.6%, and average calorific value is 7832 Btu (18.22 MJ/kg). Ash yields are greatest in the lower bench (59.33% db) of the 3500 bed and in the upper bench of the 4500 bed (74.61% db). (2) For lignite samples (on a whole-coal basis), the distributions of two of the HAPs (Pb and Sb) are positively related to ash yield, probably indicating an inorganic affinity for these elements. By using cluster analysis we

The German lignite industry. Historical development, resources, technology, economic structures and environmental impact. Study; Die deutsche Braunkohlenwirtschaft. Historische Entwicklungen, Ressourcen, Technik, wirtschaftliche Strukturen und Umweltauswirkungen. Studie

Energy Technology Data Exchange (ETDEWEB)

NONE

2017-05-15

Lignite has a key role to play in the transformation of the energy system due to its specific structural features in terms of industry, company history, policy, economics, the environment and regional structures. Understanding these structural features of the German lignite industry is an important requirement for classifying the significance of the lignite industry up to now and for the redesigning of this industrial sector. From these environmental, economic and regulatory structural characteristics, which are interwoven in a variety of ways, the incentives arise for the mining and power plant operators to react to energy price signals or energy policy steering. The aim of this research study is to define these structural features, to compile comprehensively the basic data and information that is not always transparently available, to understand the interactions, to enable the navigation of issues that are partly very complex, and to classify into the long-term developments that are especially important for political and social processes. In 2016 approx. 12 percent of German primary energy consumption was met using lignite. At the same time, lignite has the highest carbon dioxide (CO2) emissions of the fossil fuels; it currently accounts for approx. 19 percent of Germany's total greenhouse gas emissions as well as approx. 46 percent of the total CO2 emissions of the electricity sector. As a result of the mining of lignite and its conversion into electricity, substantial adverse impacts beyond the entry of greenhouse gases into the Earth's atmosphere arise for other environmental media. These impacts include half of Germany's mercury emissions, approx. a third of its sulfur dioxide emissions and approx. a tenth of its nitrogen oxide emissions. Lignite mining in open-cast mines takes up a substantial amount of landscape and soil and requires huge interventions in the water balance. Relatively high costs arise for the recultivation and rehabilitation

Characteristics of residues from thermally treated anaerobic sludges

International Nuclear Information System (INIS)

Friedman, A.A.; Smith, J.E.; De Santis, J.; Ptak, T.; Ganley, R.C.

1988-01-01

Sludge management and disposal are probably the most difficult and expensive operations involved in wastewater treatment today. To minimize final disposal costs many waste treatment facilities practice some form of anaerobic digestion and dewatering to reduce the volume and offensiveness of their by-product sludges. One potential alternative for reducing sludge volumes consists of high temperature, partial oxidation of these previously digested sludges (PDS) and subsequent anaerobic biological conversion of resulting soluble organics to methane. This paper describes solids destruction, residue characteristics and biodegradability factors that should be considered in the design of liquid thermal treatment processes for the management of anaerobic sludges. To date only very limited information is available concerning the suitability of thermally treated PDS to serve as a substrate for the generation of methane. The primary objective of this research was to determine the feasibility of producing methane efficiently from the residual VSS in anaerobically digested sludges. Secondary goals were to establish the ''best'' conditions for thermal treatment for solubilizing PDS, to observe the effect of the soluble products on methanogenesis and to evaluate process sidestreams for dewaterability and anaerobic biodegradability

Thermally-treated Pt-coated silicon AFM tips for wear resistance in ferroelectric data storage

International Nuclear Information System (INIS)

Bhushan, Bharat; Palacio, Manuel; Kwak, Kwang Joo

2008-01-01

In ferroelectric data storage, a conductive atomic force microscopy (AFM) probe with a noble metal coating is placed in contact with a lead zirconate titanate (PZT) film. The understanding and improvement of probe tip wear, particularly at high velocities, is needed for high data rate recording. A commercial Pt-coated silicon AFM probe was thermally treated in order to form platinum silicide at the near-surface. Nanoindentation, nanoscratch and wear experiments were performed to evaluate the mechanical properties and wear performance at high velocities. The thermally treated tip exhibited lower wear than the untreated tip. The tip wear mechanism is adhesive and abrasive wear with some evidence of impact wear. The enhancement in mechanical properties and wear resistance in the thermally treated film is attributed to silicide formation in the near-surface. Auger electron spectroscopy and electrical resistivity measurements confirm the formation of platinum silicide. This study advances the understanding of thin film nanoscale surface interactions

The Mineral Character and Geomechanical Properties of the Transitional Rocks from the Mesozoic-Neogene Contact Zone in the Bełchatów Lignite Deposit

OpenAIRE

Agnieszka Pękala

2014-01-01

Purpose: Beginning more than 30 years ago, opencast lignite mining in the "Bełchatów" area is an important source of accompanying minerals. Lignite mining in the "Bełchatów" mine yields, on average, more than 35 million tonnes per annum and requires removing more than 110 million cubic meters of overburden. Therefore the mine outside of the main mineral exploitation of lignite, leads to a large-scale economy of accompanying minerals. Part of the minerals are present in the overburden and are ...

Comparative palynology of clastics and lignites from the Manning Formation, Jackson Group, Upper Eocene, Grimes County, TX

Energy Technology Data Exchange (ETDEWEB)

Gennett, J.A. [Texas A& M Univ., College Station, TX (United States)

1996-09-01

The 3500 lignite seam at the Gibbons Creek Mine in Grimes County, TX was sampled for pollen and spores at 10 cm intervals. The majority of samples are dominated (to 60%) by Momipites from the Juglandaceae (walnut family), as is typical of Jackson Group sediments. Other palynomorph taxa vary systematically, with a peak of pollen of the freshwater tree Nyssa (blackgum) and associated Rboipites angustus (to 17%) occurring at the base. Higher in the seam, increase (to 55%) of Cupuliferoipollenites (a chestnut-like grain) and Cyrillaceae-pollenites? ventosus (to 7%) percentages may indicate a higher salinity environment. A Chrysophyllum (satin leaf) peak (to 25%) near the top of the seam suggests relatively shallow fresh-water conditions. Core samples from an interval above the lignites represent a transgressive-regressive cycle in inner shelf clastics. These samples were taken at 40 cm or greater intervals and reveal the regional pollen flora. Although minor changes occur, palynomorph spectra are for the most part homogenous. The dominant grain is again Momipites coryloides, but in general percentages are lower (to 35%). Cupuliferoipollenites (to 17%), Chrysophyllum (to 5%), and Rhoipites angustus (to 3%) are not less important, but do not peak as they do in the lignite spectra. Palm leaf megafossils; in one sample suggest a clastic wetland; in this sample palm pollen (mostly Arecipites, representing the modern saw palmetto) reaches 73%. Another sample contains high (26%) percentages of the fern spore Lygodiumsporites adriennis. High percentages of these two taxa do not occur in the lignite samples.

Thermally treated grass fibers as colonizable substrate for beneficial bacterial inoculum

NARCIS (Netherlands)

Trifonova, R.D.; Postma, J.; Ketelaars, J.J.M.H.; Elsas, van J.D.

2008-01-01

This study investigates how thermally treated (i.e., torrefied) grass, a new prospective ingredient of potting soils, is colonized by microorganisms. Torrefied grass fibers (TGF) represent a specific colonizable niche, which is potentially useful to establish a beneficial microbial community that

Parametric Thermal Models of the Transient Reactor Test Facility (TREAT)

Energy Technology Data Exchange (ETDEWEB)

Bradley K. Heath

2014-03-01

This work supports the restart of transient testing in the United States using the Department of Energy’s Transient Reactor Test Facility at the Idaho National Laboratory. It also supports the Global Threat Reduction Initiative by reducing proliferation risk of high enriched uranium fuel. The work involves the creation of a nuclear fuel assembly model using the fuel performance code known as BISON. The model simulates the thermal behavior of a nuclear fuel assembly during steady state and transient operational modes. Additional models of the same geometry but differing material properties are created to perform parametric studies. The results show that fuel and cladding thermal conductivity have the greatest effect on fuel temperature under the steady state operational mode. Fuel density and fuel specific heat have the greatest effect for transient operational model. When considering a new fuel type it is recommended to use materials that decrease the specific heat of the fuel and the thermal conductivity of the fuel’s cladding in order to deal with higher density fuels that accompany the LEU conversion process. Data on the latest operating conditions of TREAT need to be attained in order to validate BISON’s results. BISON’s models for TREAT (material models, boundary convection models) are modest and need additional work to ensure accuracy and confidence in results.

Biowaste utilization in the process of co-gasification with bituminous coal and lignite

International Nuclear Information System (INIS)

Howaniec, Natalia; Smoliński, Adam

2017-01-01

Biowaste utilization in co-gasification with bituminous coal and lignite gives the benefits of stable supplies of a primary energy source – coal and utilization of a zero-emission, waste material (i.e. agriculture waste, sewage sludge, etc.) with higher process efficiency and lower negative environmental impact than biomass or coal gasification, respectively. The main focus of the study presented is co-gasification of bituminous coal or lignite with biowaste to hydrogen-rich gas. The experiments were performed in the laboratory scale fixed-bed reactor installation at 700 and 900 °C. The Hierarchical Clustering Analysis complemented with a color map of studied data were applied in the selection of the optimal operating parameters for biowaste utilization in the co-gasification process based on the experimental data of gasification/co-gasification process as well as physical and chemical properties of fuels tested. The experimental results showed that the carbon conversion rate in co-gasification increased with increasing biomass content in a fuel. The total gas volume and hydrogen volume in co-gasification were higher than the values expected based on the results of the gasification process of the fuels analyzed. - Highlights: • Biowaste co-gasification with bituminous coal/lignite to hydrogen-rich gas. • Steam co-gasification in laboratory scale fixed-bed reactor at 700 and 900 °C. • Hierarchical Clustering Analysis complemented with color map of experimental data. • Carbon conversion increase with increasing biomass content. • The highest total gas and hydrogen volume in co-gasification of C-B20 blend at 900C.

Technological and Thermal Properties of Thermoplastic Composites Filled with Heat-treated Alder Wood

Directory of Open Access Journals (Sweden)

Mürşit Tufan

2016-02-01

Full Text Available This study investigated the effect of heat-treated wood content on the water absorption, mechanical, and thermal properties of wood plastic composites (WPCs. The WPCs were produced from various loadings (30, 40, and 50 wt% of heat-treated and untreated alder wood flours (Alnus glutinosa L. using high-density polyethylene (HDPE with 3 wt% maleated polyethylene (MAPE coupling agent. All WPC formulations were compression molded into a hot press for 3 min at 170 ºC. The WPCs were evaluated using mechanical testing, Fourier transform infrared spectroscopy (FTIR, thermogravimetric analysis (TGA, and differential scanning calorimetry (DSC. The mechanical property values of the WPC specimens decreased with increasing amounts of the heat-treated wood flour, except for the tensile modulus values. The heat treatment of alder wood slightly increased the thermal stability of the WPCs compared with the reference WPCs. The crystallization degree (Xc and the enthalpy of crystallization of the WPCs slightly decreased with increasing content of the heat-treated wood flour. However, all WPCs containing the heat-treated alder wood flour showed a higher crystallinity degree than that of the virgin HDPE.

Estimation of spatial variability of lignite mine dumping ground soil properties using CPTu results

Directory of Open Access Journals (Sweden)

Bagińska Irena

2016-03-01

Full Text Available The paper deals with application of CPTu test results for the probabilistic modeling of dumping grounds. The statistical measures use results from 42 CPT test points located in the lignite mine dumping ground from the region of Central Europe. Both the tip resistance qc as well as local friction fs are tested. Based on the mean values and standard deviations of measured quantities the specific zones in the dumping site profile are distinguished. For three main zones standard deviations of linearly de-trended functions, distributions of normalized de-trended values for qc and fs are examined. Also the vertical scales of fluctuation for both measured quantities are estimated. The obtained result shows that lignite mine dumping site can be successfully described with the Random Field Theory. Additional use of fs values introduces supplementary statistical information.

Perspectives on the German lignite industry in 2012. Stability through diversity; Perspektiven der deutschen Braunkohlenindustrie 2012. Stabilitaet durch Vielfalt

Energy Technology Data Exchange (ETDEWEB)

Lambertz, Johannes F. [RWE Power AG, Koeln (Germany); Milojcic, George [Bundesverband Braunkohle (DEBRIV), Koeln (Germany)

2012-07-15

The formula - stability through diversity - stands for a promising approach to energy policy. Germany will be phasing out nuclear energy by 2022 and giving a big push to renewables as a substitute. That changes the electricity mix. In this setting, lignite becomes more valuable as base load energy. Any look at the history of technology shows that, in the competition to find good solutions, experience proves that diversity is generated, and that means stability. In the energy sector, no one solution will determine the future, but many different technologies will co-exist in a pattern that is increasingly networked and integrated. The background here is a combination of nature circumstances, the wishes of consumers and, of course, the technical potential and availability of raw materials. There is no sign that coal, which is so abundantly available and competitive worldwide, will be excluded from the energy mix any time soon. The figures prove the contrary. The dynamism of world coal consumption speaks an unequivocal language. Germany, with its lignite, has a valuable natural resource which will be available for a long time to come. Germany's energy-policy aim should be to make use of the strengths of domestic lignite, strengths like security of supply and affordability, while working on minimising CO{sub 2} emissions, in particular through increases in efficiency and, in the long run, through CCS. Indispensable for this are the underlying production conditions. At the start, I had a word of thanks for our many partners for their good cooperation. We go on relying on your support. Specifically, we hope that the lignite industry, like other sectors will go on being appreciated for the benefits that it brings, and that no additional burdens are envisaged that might impair its competitiveness. It is our task in the lignite industry to further develop the potential of lignite with our wealth of ideas and fact-driven work. The good of today thus make a better

Extraction of organic materials from red water by metal-impregnated lignite activated carbon

Energy Technology Data Exchange (ETDEWEB)

Wei, Fangfang [State Key Laboratory of Geological Processes and Mineral Resources, National Laboratory of Mineral Materials, School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Zhang, Yihe, E-mail: zyh@cugb.edu.cn [State Key Laboratory of Geological Processes and Mineral Resources, National Laboratory of Mineral Materials, School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon, Hong Kong (China); Lv, Fengzhu [State Key Laboratory of Geological Processes and Mineral Resources, National Laboratory of Mineral Materials, School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Chu, Paul K. [Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon, Hong Kong (China); Ye, Zhengfang, E-mail: zhengfangye@163.com [Department of Environmental Engineering, Key Laboratory of Water and Sediment Sciences of the Ministry of Education, Peking University, Beijing 100871 (China)

2011-12-15

Highlights: Black-Right-Pointing-Pointer Metal-impregnated lignite activated carbon was investigated as adsorbent. Black-Right-Pointing-Pointer Adsorbent for the extraction of organic materials from 2,4,6-trinitrotoluene (TNT) red water. Black-Right-Pointing-Pointer Effects of different metals on the extraction were investigated and discussed. Black-Right-Pointing-Pointer Many loading factors of Cu{sup 2+} were found having great influences on the extraction. Black-Right-Pointing-Pointer Extraction performances and mechanism of TNT red water on Cu/LAC were investigated. - Abstract: Extraction of organic materials from 2,4,6-trinitrotoluene (TNT) red water by lignite activated carbon (LAC) impregnated with Cu{sup 2+}, Ba{sup 2+}, Sn{sup 2+}, Fe{sup 3+}, Ca{sup 2+} and Ag{sup +} was investigated. The affinity to organic materials in red water was found to follow the order: Cu/LAC > Sn/LAC > Ag/LAC > Ba/LAC > Fe/LAC > Ca/LAC, which was explained by the hard and soft acid base (HSAB) theory. Cu{sup 2+} showed the best performance and several parameters were further studied. X-ray photoelectron spectroscopy (XPS) verified effective loading of Cu{sup 2+} on the LAC surface. The water quality before and after treated by Cu/LAC was evaluated using high performance liquid chromatograph, Gas Chromatography/Mass Spectroscopy (GC/MS), UV-vis spectroscopy and other analyses. The extraction performances and mechanism of organic materials on Cu/LAC were investigated through static methods. The experimental results showed that Cu/LAC possessed stronger extraction ability for the sulfonated nitrotoluenes than the non-sulfonated nitrotoluenes, the kinetic data fitted the pseudo-second-order kinetic model well. In addition, the leaching out of Cu{sup 2+} from Cu/LAC was found much lower in the 100 times diluted red water (0.074%) than in the raw water (10.201%). Column adsorptions with more concentrated red water were also studied. Finally, Cu/LAC was observed to possess excellent

Use of residual hydrocarbons treated by Thermal Plasma (recovery of energy by-products)

International Nuclear Information System (INIS)

Carreno B, J.A.; Pacheco S, J.O.; Ramos F, F.; Cruz A, A.; Duran G, M.

2001-01-01

The emergence of new technologies is getting greater importance for the control of pollution. One of them is the destruction of hazardous wastes treated by thermal plasma, which is of special interest for the efficient treatment of the hazardous wastes since the heat generated by thermal plasma is able to destroy the molecular bonds generating solids and gaseous products which do not represent danger for the human being and the environment. The thermal plasma is the suitable technology for treating a wide range of hazardous wastes, including the residual hydrocarbons from the refinement process of petroleum, plasma exceeds the barrier of 3000 Centigrade. The efficiency of the degradation of residues is greater than 99.99%. Toxic emissions are not generated to environment as SO 2 , NO x and CO 2 neither dioxins and furans by being a pyrolysis process. The use of hydrogen as fuel does not generate pollution to environment. (Author)

Condition-Based Conveyor Belt Replacement Strategy in Lignite Mines with Random Belt Deterioration

Science.gov (United States)

Blazej, Ryszard; Jurdziak, Leszek

2017-12-01

In Polish lignite surface mines, condition-based belt replacement strategies are applied in order to assure profitable refurbishment of worn out belts performed by external firms specializing in belt maintenance. In two of three lignite mines, staff asses belt condition subjectively during visual inspections. Only one mine applies specialized diagnostic device (HRDS) allowing objective magnetic evaluation of belt core condition in order to choose the most profitable moment for the dismantling of worn out belt segments from conveyors and sending them to the maintenance firm which provides their refurbishment. This article describes the advantages of a new diagnostic device called DiagBelt. It was developed at the Faculty of Geoengineering, Mining and Geology, Wroclaw University of Science and Technology. Economic gains from its application are calculated for the lignite mine and for the belt maintenance firm, taking into account random life (durability) of new and reconditioned belts (after the 1st and the 2nd refurbishment). Recursive calculations for following years allow the estimation of the length and costs of replaced, reconditioned and purchased belts on an annual basis, while the use of the Monte Carlo method allows the estimation of their variability caused by random deterioration of belts. Savings are obtained due to better selection of moments (times) for the replacement of belt segments and die to the possibility to qualify worn out belts for refurbishment without the need to remove their covers. In effect, increased belt durability and lowered share of waste belts (which were not qualified for reconditioning) create savings which can quickly cover expenditures on new diagnostic tools and regular belt inspections in the mine.

Refining of raw materials, lignite present economic problems

Energy Technology Data Exchange (ETDEWEB)

Schirmer, G.

1985-06-01

East Germany seeks an economic intensification program that involves refining raw materials to a higher level. Lignite briquetting prior to liquefaction and gasification illustrates both the theoretical and practical aspects of that goal and also introduces questions of secure supplies. The author describes the special labor processes, use of technology, recycling of waste materials, and other new problems that the approach entails as the refined raw materials become new materials or energy sources. Economics based on the value of the refined product and the cost of the materials determine the degree of refinement. The concept also involves the relationship of producer and user as profits increase.

Employment benefits of electricity generation. A comparative assessment of lignite and natural gas power plants in Greece

International Nuclear Information System (INIS)

Tourkolias, C.; Damigos, D.; Diakoulaki, D.; Mirasgedis, S.

2009-01-01

This paper aims at developing an integrated approach for estimating the employment benefits associated with power-generation technologies. The proposed approach exploits the input-output methodology for estimating the direct, indirect and induced employment effects associated with the energy project in question, as well as two different valuation techniques, namely the 'opportunity cost of labour' approach and the 'public expenditures' approach, for expressing these effects in monetary terms. This framework has been implemented to estimate the employment benefits resulting from the development of a lignite-fired and a natural gas-fired power plant in Greece, taking into account all the stages of the corresponding fuel cycles that are undertaken domestically. The results of the analysis clearly show that lignite-fired electricity generation results in significant employment benefits amounting to 2.9-3.5 EUR/MWh in the basic scenario. On the other hand, the employment benefits associated with the examined natural gas unit were estimated at 0.4-0.6 EUR/MWh in the basic scenario. It is also worth mentioning that the significant environmental externalities of the lignite-fired electricity in Greece that have been presented in a number of studies can only be partially compensated by the estimated employment benefits. (author)

Cytocompatibility of Plasma and Thermally Treated Biopolymers

Directory of Open Access Journals (Sweden)

Petr Slepička

2013-01-01

Full Text Available This paper is focused on the surface characterization of plasma and consequently thermally treated biocompatible polymers. PLLA (poly(L-lactide acid and PMP (poly-4-methyl-1-pentene are studied. The influence of Ar plasma treatment on the surface polarity of substrate measured immediately after treatment and during the polymer surface aging is studied. Surface roughness, morphology, wettability, and surface chemistry were determined. Plasma treatment leads to significant changes in PLLA surface morphology and chemistry, with the PMP being slightly affected. The higher resistance to plasma fluence results in smaller ablation of PMP than that of PLLA. The plasma treatment improves cell adhesion and proliferation on the PMP. Plasma treatment of PLLA influences mostly the homogeneity of adhered and proliferated VSMC.

Combustion of producer gas from gasification of south Sumatera lignite coal using CFD simulation

Directory of Open Access Journals (Sweden)

Vidian Fajri

2017-01-01

Full Text Available The production of gasses from lignite coal gasification is one of alternative fuel for the boiler or gas turbine. The prediction of temperature distribution inside the burner is important for the application and optimization of the producer gas. This research aims to provide the information about the influence of excess air on the temperature distribution and combustion product in the non-premixed burner. The process was carried out using producer gas from lignite coal gasification of BA 59 was produced by the updraft gasifier which is located on Energy Conversion Laboratory Mechanical Engineering Department Universitas Sriwijaya. The excess air used in the combustion process were respectively 10%, 30% and 50%. CFD Simulations was performed in this work using two-dimensional model of the burner. The result of the simulation showed an increase of excess air, a reduction in the gas burner temperature and the composition of gas (carbon dioxide, nitric oxide and water vapor.

Environmental impact assessment of coal fired thermal power stations

International Nuclear Information System (INIS)

Nambi, K.S.V.; Sadasivan, S.; Negi, B.S.; Meenakshy, V.

1992-01-01

Coal fly ash samples collected from various thermal power plants and one lignite ash sample were analysed for various elements such as As, Ca, Ce, Co, Cr, Cu, Eu, Fe, Hf, K, La, Lu, Mn, Na, Ni, Pb, Rb, Se, Si, Sb, Sc, Sm, Sr, Ti, V, Yb and Zn using energy dispersive X-ray fluorescence and instrumental neutron activation analysis methods. The two-step maximum leachability test was also performed on all fly ash samples. 13 refs, 9 tabs

EFFECT OF MICROWAVE DRYING ON THE GRINDABILITY OF LIGNITE COAL

OpenAIRE

Güngören, Can; Özkan, Şafak Gökhan; Hacıfazlıoğlu, Hasan

2016-01-01

In this study, the representative lignite coal samples supplied from Kastamonu-Tosya region were dried in a conventional drying oven and a microwave oven, and then they were ground by a laboratory rod mill. The particle size analyses of the ground samples at various grinding times (10, 20, 30, and 60 minutes) were carried out, and the results were compared. As a result, the d80 particle sizes of the samples, dried in the conventional drying oven, were determined as 350, 183, 180, and 100 µm a...

Elemental characterization of lignite from Afsin-Elbistan in Turkey by k(0)-NAA

Czech Academy of Sciences Publication Activity Database

Kubešová, Marie; Orucoglu, E.; Haciyakupoglu, S.; Erenturk, S.; Krausová, Ivana; Kučera, Jan

2016-01-01

Roč. 308, č. 3 (2016), s. 1055-1062 ISSN 0236-5731 R&D Projects: GA ČR(CZ) GBP108/12/G108; GA MŠk(CZ) LM2011019 Institutional support: RVO:61389005 Keywords : Lignite * Afsin * Elbistan * neutron activation analysis * k(0) standardization Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 1.282, year: 2016

Numerical analysis of single and multiple particles of Belchatow lignite dried in superheated steam

Science.gov (United States)

Zakrzewski, Marcin; Sciazko, Anna; Komatsu, Yosuke; Akiyama, Taro; Hashimoto, Akira; Kaneko, Shozo; Kimijima, Shinji; Szmyd, Janusz S.; Kobayashi, Yoshinori

2018-03-01

Low production costs have contributed to the important role of lignite in the energy mixes of numerous countries worldwide. High moisture content, though, diminishes the applicability of lignite in power generation. Superheated steam drying is a prospective method of raising the calorific value of this fuel. This study describes the numerical model of superheated steam drying of lignite from the Belchatow mine in Poland in two aspects: single and multi-particle. The experimental investigation preceded the numerical analysis and provided the necessary data for the preparation and verification of the model. Spheres of 2.5 to 30 mm in diameter were exposed to the drying medium at the temperature range of 110 to 170 °C. The drying kinetics were described in the form of moisture content, drying rate and temperature profile curves against time. Basic coal properties, such as density or specific heat, as well as the mechanisms of heat and mass transfer in the particular stages of the process laid the foundations for the model construction. The model illustrated the drying behavior of a single particle in the entire range of steam temperature as well as the sample diameter. Furthermore, the numerical analyses of coal batches containing particles of various sizes were conducted to reflect the operating conditions of the dryer. They were followed by deliberation on the calorific value improvement achieved by drying, in terms of coal ingredients, power plant efficiency and dryer input composition. The initial period of drying was found crucial for upgrading the quality of coal. The accuracy of the model is capable of further improvement regarding the process parameters.

Paleoenvironmental implications from biomarker and stable isotope investigations on the Pliocene Velenje lignite seam (Slovenia)

Energy Technology Data Exchange (ETDEWEB)

Bechtel, A.; Sachsenhofer, R.F.; Markic, M.; Gratzer, R.; Lucke, A.; Puttmann, W. [Montan University of Leoben, Leoben (Austria)

2003-07-01

A Pliocene lignite seam up to 160 m thick occurs in the Velenje basin (Slovenia). The seam originated in a topogenous mire and evolved within a non-marine, transgressive setting. Differences in soluble organic matter yield and hydrocarbon content of borehole samples from the lignite are related to differences in the composition of free lipids of microbial origin and/or hydrocarbons derived from the biogeochemical degradation of plant tissue. Variations of the redox conditions within the mire are reflected by pristane/phytane ratios. The abundance of terpenoid biomarkers indicates the predominance of gymnosperms over angiosperms, which is consistent with palynomorphic spectra dominated by pollen of the Sequoia-Taxodium-Metasequoia plant community rather than by angiosperms. Evidence is also provided that the content of land plant derived biomarkers and the preservation of plant tissue is controlled by the input of resin-rich, decay-resistant conifers.

PFBC development for lignite-fired CC power plants

Energy Technology Data Exchange (ETDEWEB)

Bauer, F.; Meier, H.J.; Smuda, J.V.; Stuhlmueller, F. [VEAG Vereinigte Energiewerke AG (Germany)

1994-12-31

A power station design based on pressurised combustion in a circulating fluid-bed is used to illustrate the principle, layout and potential of a lignite-fired combined power station. The fundamental reasons for concentrating on the circulating pressurised fluid-bed consist in its improved emission values, the possibility of separating heat source and heat sink, and better operating performance (part-load). This design has been developed as part of a feasibility study supported by the Federal Ministry for Research and Tehcnology. The paper describes the design of the power plant components. Combustion trials carried out at the pilot plant in Friedrichsfield are reported and the cost-effectiveness of the innovatory design discussed. 10 figs.

Environmental assessment of remedial action at the inactive uraniferous lignite processing sites at Belfield and Bowman, North Dakota

International Nuclear Information System (INIS)

Beranich, S.; Berger, N.; Bierley, D.; Bond, T.M.; Burt, C.; Caldwell, J.A.; Dery, V.A.; Dutcher, A.; Glover, W.A.; Heydenburg, R.J.; Larson, N.B.; Lindsey, G.; Longley, J.M.; Millard, J.B.; Miller, M.; Peel, R.C.; Persson-Reeves, C.H.; Titus, F.B.; Wagner, L.

1989-09-01

The Uranium Mill Tailings Radiation Control Act of 1978 (UMTRCA), to clean up the Belfield and Bowman, North Dakota, uraniferous lignite processing sites to reduce the potential health impacts associated with the residual radioactive materials remaining at these sites. Remedial action at these sites must be performed in accordance with the US Environmental Protection Agency's (EPA) standards promulgated for the remedial action and with the concurrence of the US Nuclear Regulatory Commission (NRC) and the state of North Dakota. The inactive Belfield uraniferous lignite processing site is one mile southeast of Belfield, North Dakota. The inactive Bowman uraniferous lignite processing site at the former town of Griffin, is seven miles northwest of Bowman, North Dakota and 65 road miles south of Belfield. Lignite ash from the processing operations has contaminated the soils over the entire 10.7-acre designated Belfield site and the entire 12.1-acre designated Bowman site. Dispersion of the ash has contaminated an additional 20.6 acres surrounding the Belfield processing site and an additional 59.2 acres surrounding the Bowman processing site. The proposed remedial action is to relocate the contaminated materials at the Belfield processing site to the Bowman processing/disposal site for codisposal with the Bowman contaminated soils. The environmental impacts assessed in this EA were evaluated for the proposed remedial action and the no action alternative and demonstrate that the proposed action would not significantly affect the quality of the human environment and would be performed in compliance with applicable environmental laws. The no action alternative would not be consistent with the intent of Public Law 95-604 and would not comply with the EPA standards. 48 refs., 10 figs., 7 tabs

Evaluation of naturally occurring pigments of the North Bohemian lignite mining area; Bewertung von mineralischen Pigmentvorkommen des nordboehmischen Braunkohlenbeckens

Energy Technology Data Exchange (ETDEWEB)

Buntenbach, Stephan [TriMin Consulting - Mineral Processing, Ammerthal (Germany); Botula, Jiri [VSB-Technical Univ. of Ostrava (Czech Republic). Mineral Processing Dept.; Leonhardt, Hana

2010-11-15

The research project ''Mineral Processing Methods for the Preparation of Naturally Occurring Pigments from Overburden of the Lignite Mines and from Shallow Clay Deposits of the North Bohemian Lignite Basin'', funded by the Deutsche Bundesstiftung Umwelt DBU, was conducted as a collaboration between the AKW Apparate+Verfahren GmbH, Hirschau with the Technical University of Ostrava. Geological, mineralogical and mineral processing studies for the development of a suitable beneficiation method were carried out to investigate the possibilities of the industrial usage of beneficiated pigments of these deposits. It should be demonstrated, that the significant reserves of mineral pigments in the shallow deposits and also in the overburden of the lignite mines can be utilized ecologically and economically. Based on the results of geological prospecting work already carried out, the deposit Horenec was selected as the most important pigment deposits for the production of bolus and ochre earth. The newly carried out geological, mineralogical and chemical studies formed the basis for the following mineral processing test work and the test work for the usage of beneficiated products as colouring paint for plastic, fabric and other materials. (orig.)

Using cement, lignite fly ash and baghouse filter waste for solidification of chromium electroplating treatment sludge

Directory of Open Access Journals (Sweden)

Wantawin, C.

2004-02-01

Full Text Available The objective of the study is to use baghouse filter waste as a binder mixed with cement and lignite fly ash to solidify sludge from chromium electroplating wastewater treatment. To save cost of solidification, reducing cement in binder and increasing sludge in the cube were focused on. Minimum percent cement in binder of 20 for solidification of chromium sludge was found when controlling lignite fly ash to baghouse filter waste at the ratio of 30:70, sludge to binder ratio of 0.5, water to mixer ratio of 0.3 and curing time of 7 days. Increase of sludge to binder ratio from 0.5 to 0.75 and 1 resulted in increase in the minimum percent cement in binder up to 30 percent in both ratios. With the minimum percent cement in binder, the calculated cement to sludge ratios for samples with sludge to binder ratios of 0.5, 0.75 and 1 were 0.4, 0.4 and 0.3 respectively. Leaching chromium and compressive strength of the samples with these ratios could achieve the solidified waste standard by the Ministry of Industry. For solidification of chromium sludge at sludge to binder ratio of 1, the lowest cost binder ratio of cement to lignite fly ash and baghouse filter waste in this study was 30:21:49. The cost of binder in this ratio was 718 baht per ton dry sludge.

COFIRING BIOMASS WITH LIGNITE COAL; F

International Nuclear Information System (INIS)

Darren D. Schmidt

2001-01-01

As of September 28, 2001, all the major project tasks have been completed. A presentation was given to the North Dakota State Penitentiary (NDSP) and the North Dakota Division of Community Services (DCS). In general, the feasibility study has resulted in the following conclusions: (1) Municipal wood resources are sufficient to support cofiring at the NDSP. (2) Steps have been taken to address all potential fuel-handling issues with the feed system design, and the design is cost-effective. (3) Fireside issues of cofiring municipal wood with coal are not of significant concern. In general, the addition of wood will improve the baseline performance of lignite coal. (4) The energy production strategy must include cogeneration using steam turbines. (5) Environmental permitting issues are small and do not affect economics. (6) The base-case economic scenario provides for a 15-year payback of a 20-year municipal bond and does not include the broader community benefits that can be realized

Study relating to the conceptual design and cost estimates of the Saskatchewan Power Corporation lignite beneficiation process, Phase IV: Final report

Energy Technology Data Exchange (ETDEWEB)

Granatstein, D L; Champagne, P J; Szladow, A J

1982-01-01

The lignite beneficiation process produces a clean, environmentally acceptable and economical source of energy which offers many benefits to Saskatchewan, the public utilities and private industry. This document provides: A detailed assessment of the overall feasibility of the proposed process and its suitablity for successful commercialization; an economic evaluation including a sensitivity analysis of the major process uncertainties and alternate case analyses; an analysis of the market for beneficiated lignite; an analysis of the credits applicable to such a beneficiated product; and an outline of recommendation for process improvements and future process research and development.

The need for verification of the Polish lignite deposits owing to development and nature conservation protection on land at the surface

Directory of Open Access Journals (Sweden)

Naworyta Wojciech

2016-12-01

Full Text Available Poland is a country rich in lignite. The area where the lignite occurs occupies approx. 22% of the total surface area of the country. Geological resources of Polish lignite deposits are estimated at 23.5 billion Mg, but in the majority (69% the accuracy of their identification is poor. Nevertheless the amount of coal in Polish deposits allows - at least in theory - for mining and energy production at the current level for hundreds of years to come. It is an important raw material for the energy security of the country both currently and in the future. Because the vast majority of Polish and foreign mines use an open pit method for lignite extraction the actual amount of mineral available for the extraction depends not only on the properties of the deposit but to a large extent on the method of development of the surface land above the deposit, as well as on the sensitivity of the environment in the vicinity of any future mines. After careful analysis it can be stated that only a few of the lignite deposits may be subject to cost-effective mining operations. These deposits should be subjected to special protection as a future resource base which will ensure the energy security of the country. Some examples of domestic deposits have been presented where due to the conflict resulting from the development of the area should be deleted from the Balance Sheet of Mineral Deposits because their exploitation is irrational and uneconomic. Keeping such deposits in the Balance Sheet, and the use of large numbers in the context of their resource base leads to an unwarranted sense of wealth which consequently does not encourage the protection of these deposits which may actually be subject to rational exploitation in the near future. In summary there is a need to find a compromise in order to adequately protect all natural resources including mineral deposits.

Scientific investigations accompanying recultivation of abandoned lignite mines in East Germany. Research projects 1994 through 2000; Wissenschaftliche Begleitung der ostdeutschen Braunkohlesanierung. Forschungsprojekte 1994 bis 2000

Energy Technology Data Exchange (ETDEWEB)

Gockel, G.; Hildmann, E.; Schlenstedt, J.; Schreiber, M. (comps.)

2001-07-01

From 1990 the reduction of lignite mining on the territory of the German Democratic Republic (GDR) led to the closure of plants for the production and processing of lignite. This entailed a dramatic demand of redevelopment and transformation of former mining and industrial areas of lignite industry and the creation of the industrial branch of remediation of post-lignite-mining areas, for which suitable structures of management and financing had to be found. The target of these endeavours is the creation of multifunctional to follow former surface mining areas. Ecological and security criteria play an eminent part in this process. Stabilising slopes, recultivation, rehabilitation of a balanced water regime and the elimination of dangers emanating from groundwater and soil contamination by earlier industrial use have particular priority. Recultivation requires scientific preparation and surveillance. Deficits are discussed that have led to the invitation of tenders for a promotion initiative and resulted in the implementation of a number of research projects. This publication deals with the presentation of the tasks and research approaches as well as the description and evaluation of results with the view of their applicability. (orig.)

Hydrogen-rich gas as a product of two-stage co-gasification of lignite/waste mixtures

Czech Academy of Sciences Publication Activity Database

Straka, Pavel; Bičáková, Olga

2014-01-01

Roč. 39, č. 21 (2014), s. 10987-10995 ISSN 0360-3199 Institutional support: RVO:67985891 Keywords : co-gasification * waste plastics * lignite * hydrogen-rich gas Subject RIV: DM - Solid Waste and Recycling Impact factor: 3.313, year: 2014 http://authors.elsevier.com/sd/article/S0360319914014025

Re-evaluation of the age of the Brandon Lignite (Vermont, USA) based on plant megafossils. [USA - Vermont

Energy Technology Data Exchange (ETDEWEB)

Tiffney, B.H. (University of California at Santa Barbara, Santa Barbara, CA (United States). Dept. of Geological Sciences)

1994-07-01

The Brandon Lignite of west-central Vermont contains the northernmost megafossil flora of Cenozoic angiosperms, and one of the most diverse Cenozoic pollen floras in northeastern North America. While the floristic composition clearly indicates deposition of the Brandon sediments in the warmer parts of the Cenozoic, previous attempts at a more precise stratigraphic placement have been inconclusive, ranging from Cretaceous to Miocene. Re-evaluation of existing and new fruit, seed and wood data from the Brandon flora in the context of other floras in the Northern Hemisphere leads to the conservative conclusion that the deposit could range from earliest Oligocene to Early Miocene. Several lines of potentially weak evidence favor an Early Miocene age, in agreement with recent biostratigraphic data from the associated pollen flora. It is concluded that the Brandon Lignite is Early Miocene.

Quantitative spectrographic determination of traces of germanium in lignite

International Nuclear Information System (INIS)

Martin, M.; Roca, M.

1972-01-01

A burning technique in a d.c. arc at 10 amp has been employed. The standards have been prepared from a natural lignite with a low germanium content. In order to enhance sensitivity, AgCl, K 2 SO 4 , CuF 2 , Sb 2 S 3 and Bi 2 S 3 have been tested as sweeping materials. Using 2% CuF 2 a detection limit of 1 ppm germanium is attainable. Bi, Cu, Sb and Sn have been studied as internal standards: the former leads to the, highest precision (1 6%. Results show good agreement with those obtained by the addition method. (Author) 6 refs

Adsorption of an anionic dispersant on lignite

Energy Technology Data Exchange (ETDEWEB)

Yavuz, R.; Kucukbayrak, S. [Istanbul Technical University, Istanbul (Turkey). Dept. of Chemical Engineering, Chemical & Metallurgical Engineering Faculty

2001-12-01

Since coal is not a homogeneous substance but a mixture of carbonaceous materials and mineral matter, it has a variety of surface properties. Therefore, it is not easy to control the properties of coal suspensions by simply adjusting variables, such as pH and/or electrolyte. A chemical agent needs to be added to control the properties of the coal suspensions. The adsorption behavior of an anionic dispersant in the presence of a wetting agent using some Turkish lignite samples was investigated. The effects of dispersant concentration, temperature and pH on the dispersant adsorption were studied systematically, and the experimental results are presented. Pellupur B69 as a dispersant, commercial mixture of formaldehyde condensate sodium salt of naphthalene sulphonic acid, and Texapon N{sub 2}5 as a wetting agent, a sodium lauryl ether sulfate, have been used.

Spatiotemporal mapping of ground water pollution in a Greek lignite basin, using geostatistics

Energy Technology Data Exchange (ETDEWEB)

Modis, K. [National Technical Univ. of Athens, Athens (Greece)

2010-07-01

An issue of significant interest in the mining industry in Greece is the occurrence of chemical pollutants in ground water. Ammonium, nitrites and nitrates concentrations have been monitored through an extensive sampling network in the Ptolemais lignite opencast mining area in Greece. Due to intensive mining efforts in the area, the surface topology is continuously altered, affecting the life span of the water boreholes and resulting in messy spatiotemporal distribution of data. This paper discussed the spatiotemporal mapping of ground water pollution in the Ptolemais lignite basin, using geostatistics. More specifically, the spatiotemporal distribution of ground water contamination was examined by the application of the bayesian maximum entropy theory which allows merging spatial and temporal estimations in a single model. The paper provided a description of the site and discussed the materials and methods, including samples and statistics; variography; and spatiotemporal mapping. It was concluded that in the case of the Ptolemais mining area, results revealed an underlying average yearly variation pattern of pollutant concentrations. Inspection of the produced spatiotemporal maps demonstrated a continuous increase in the risk of ammonium contamination, while risk for the other two pollutants appeared in hot spots. 18 refs., 1 tab., 7 figs.

Spatiotemporal mapping of ground water pollution in a Greek lignite basin, using geostatistics

International Nuclear Information System (INIS)

Modis, K.

2010-01-01

An issue of significant interest in the mining industry in Greece is the occurrence of chemical pollutants in ground water. Ammonium, nitrites and nitrates concentrations have been monitored through an extensive sampling network in the Ptolemais lignite opencast mining area in Greece. Due to intensive mining efforts in the area, the surface topology is continuously altered, affecting the life span of the water boreholes and resulting in messy spatiotemporal distribution of data. This paper discussed the spatiotemporal mapping of ground water pollution in the Ptolemais lignite basin, using geostatistics. More specifically, the spatiotemporal distribution of ground water contamination was examined by the application of the bayesian maximum entropy theory which allows merging spatial and temporal estimations in a single model. The paper provided a description of the site and discussed the materials and methods, including samples and statistics; variography; and spatiotemporal mapping. It was concluded that in the case of the Ptolemais mining area, results revealed an underlying average yearly variation pattern of pollutant concentrations. Inspection of the produced spatiotemporal maps demonstrated a continuous increase in the risk of ammonium contamination, while risk for the other two pollutants appeared in hot spots. 18 refs., 1 tab., 7 figs.

Effect of reactor radiation on the thermal conductivity of TREAT fuel

Energy Technology Data Exchange (ETDEWEB)

Mo, Kun, E-mail: kunmo@anl.gov; Miao, Yinbin; Kontogeorgakos, Dimitrios C.; Connaway, Heather M.; Wright, Arthur E.; Yacout, Abdellatif M.

2017-04-15

The Transient Reactor Test Facility (TREAT) at the Idaho National Laboratory is resuming operations after more than 20 years in latency in order to produce high-neutron-flux transients for investigating transient-induced behavior of reactor fuels and their interactions with other materials and structures. A parallel program is ongoing to develop a replacement core in which the fuel, historically containing highly-enriched uranium (HEU), is replaced by low-enriched uranium (LEU). Both the HEU and prospective LEU fuels are in the form of UO{sub 2} particles dispersed in a graphite matrix, but the LEU fuel will contain a much higher volume of UO{sub 2} particles, which may create a larger area of interphase boundaries between the particles and the graphite. This may lead to a higher volume fraction of graphite exposed to the fission fragments escaping from the UO{sub 2} particles, and thus may induce a higher volume of fission-fragment damage on the fuel graphite. In this work, we analyzed the reactor-radiation induced thermal conductivity degradation of graphite-based dispersion fuel. A semi-empirical method to model the relative thermal conductivity with reactor radiation was proposed and validated based on the available experimental data. Prediction of thermal conductivity degradation of LEU TREAT fuel during a long-term operation was performed, with a focus on the effect of UO{sub 2} particle size on fission-fragment damage. The proposed method can be further adjusted to evaluate the degradation of other properties of graphite-based dispersion fuel.

Determining the area of influence of depression cone in the vicinity of lignite mine by means of triangle method and LANDSAT TM/ETM+ satellite images.

Science.gov (United States)

Zawadzki, Jarosław; Przeździecki, Karol; Miatkowski, Zygmunt

2016-01-15

Problems with lowering of water table are common all over the world. Intensive pumping of water from aquifers for consumption, irrigation, industrial or mining purposes often causes groundwater depletion and results in the formation of cone of depression. This can severely decrease water pressure, even over vast areas, and can create severe problems such as degradation of agriculture or natural environment sometimes depriving people and animals of water supply. In this paper, the authors present a method for determining the area of influence of a groundwater depression cone resulting from prolonged drainage, by means of satellite images in optical, near infrared and thermal infrared bands from TM sensor (Thematic Mapper) and ETM+ sensor (Enhanced Thematic Mapper +) placed on Landsat 5 and Landsat 7 satellites. The research area was Szczercowska Valley (Pol. Kotlina Szczercowska), Central Poland, located within a range of influence of a groundwater drainage system of the lignite coal mine in Belchatow. It is the biggest lignite coal mine in Poland and one of the largest in Europe exerting an enormous impact on the environment. The main method of satellite data analysis for determining soil moisture, was the so-called triangle method. This method, based on TVDI (Temperature Vegetation Dryness Index) was supported by additional spatial analysis including ordinary kriging used in order to combine fragmentary information obtained from areas covered by meadows. The results obtained are encouraging and confirm the usefulness of the triangle method not only for soil moisture determination but also for assessment of the temporal and spatial changes in the area influenced by the groundwater depression cone. The range of impact of the groundwater depression cone determined by means of above-described remote sensing analysis shows good agreement with that determined by ground measurements. The developed satellite method is much faster and cheaper than in-situ measurements

Biochar and lignite affect H+-ATPase and H+-PPase activities in root tonoplast and nutrient contents of mung bean under salt stress.

Science.gov (United States)

Torabian, Shahram; Farhangi-Abriz, Salar; Rathjen, Judith

2018-05-31

This research was conducted to evaluate effects of biochar (50 and 100 g kg -1 soil) and lignite (50 and 100 g kg -1 soil) treatments on H + -ATPase and H + -PPase activity of root tonoplast, nutrient content, and performance of mung bean under salt stress. High saline conditions increased H + -ATPase and H + -PPase activities in root tonoplast, sodium (Na) content, reactive oxygen species (H 2 O 2 and O 2 - ) generation, relative electrolyte leakage (REL) and 2,2-Diphenyl-1-picrylhydrazyl (DPPH) activity in root and leaf, but decreased relative water content (RWC), chlorophyll content index, leaf area, potassium (K), calcium (Ca), magnesium (Mg), zinc (Zn) and iron (Fe) content of plant tissues, root and shoot dry weight of mung bean. Lignite and biochar treatments decreased the H + -ATPase and H + -PPase activities of root tonoplast under salt stress. Moreover, these treatments increased the cation exchange capacity of soil and nutrient values in plant tissues. Biochar and lignite diminished the generation of reactive oxygen species and DPPH activity in root and leaf cells, and these superior effects improved chlorophyll content index, leaf area and growth of mung bean under both conditions. In general, the results of this study demonstrated that biochar and lignite decreased the entry of Na ion into the cells, enriched plant cells with nutrients, and consequently improved mung bean performance under salt toxicity. Copyright © 2018 Elsevier Masson SAS. All rights reserved.

Evaluation of radioactive emissions of lignite-fired power plants in Turkey using the Analytic Hierarchy Process

International Nuclear Information System (INIS)

Bueke, Tayfun

2013-01-01

Radioactive emissions of 13 lignite-fired power plants in Turkey are of great concern to the public and to scientists alike. The purpose of this study is to evaluate these power plants, according to their radioactive emissions by using the Analytic Hierarchy Process. Control criteria are in particular 226 Ra, 232 Th, 40 K and 238 U emissions from the power plants. These control criteria are weighted according to the objective assessment. The calculations are repeated for three different objective assessments of control criteria namely the mortality risk coefficients for inhalation, ingestion, external exposure of 226 Ra, 232 Th, 40 K and 238 U. It has been calculated that the Can lignite-fired power plant is ranking first while the Soma-B plant is ranking last according to the radioactive emissions of the power plants when the average of three different objective control criteria are used in the calculations. (orig.)

Some examples of the cavity filling along transportation routes above abandoned room and pillar lignite Mines in Tokai Region

International Nuclear Information System (INIS)

Sakamoto, A.; Yamada, N.; Sugiura, K.; Kawamoto, T.

2005-01-01

The authors describe the applications of the integrated cavity filling technique to abandoned lignite mines in Tokai region. These abandoned lignite mines were in operation until 1960's and the routes of Tokai By-Pass Expressway and the linear motor car railway line for Aichi Exposition pass over these abandoned mines. Since the size of abandoned mines were much larger than the route of the expressway and the elevated monorail, limited areas relevant to their stability had to be only filled. This article describe the details of cavity filling operations in these two projects, which may be some valuable examples for assessing the methods how to deal problems associated with mine closures in long term. (authors)

Effect of acid treated carbon nanotubes on mechanical, rheological and thermal properties of polystyrene nanocomposites

KAUST Repository

Amr, Issam Thaher

2011-09-01

In this work, multiwall carbon nanotubes (CNT) were functionalized by acid treatment and characterized using Fourier Transform Infrared Spectroscopy (FTIR) and thermogravimetric analysis (TGA). Polystyrene/CNT composites of both the untreated and acid treated carbon nanotubes were prepared by thermal bulk polymerization without any initiator at different loadings of CNT. The tensile tests showed that the addition of 0.5 wt.% of acid treated CNT results in 22% increase in Young\\'s modulus. The DSC measurements showed a decrease in glass transition temperature (Tg) of PS in the composites. The rheological studies at 190 °C showed that the addition of untreated CNT increases the viscoelastic behavior of the PS matrix, while the acid treated CNT acts as plasticizer. Thermogravimetric analysis indicated that the incorporation of CNT into PS enhanced the thermal properties of the matrix polymer. © 2011 Elsevier Ltd. All rights reserved.

Evaluation of lignite tar

Energy Technology Data Exchange (ETDEWEB)

Gossedin, A

1946-01-01

Tar from the low-temperature (450/sup 0/) carbonization of lignite from Bouches-du-Rhone was hydrogenated in the presence of a catalyst based on MoS/sub 2/ with a 3:1 H:N mixture. Processing (at 470/sup 0/ and 400 atmospheres) for maximum production of gasoline yielded 86 wt % of a product of boiling 55 to 186/sup 0/ and motor octane number 75. An alternative is to hydrogenate with a view to producing solvents and lubricants. For this purpose the tar was separated by distillation (at 20 millimeters, cutting at 220/sup 0/) into two fractions of equal volume. On hydrogenation (at 300/sup 0/ and 400 atmospheres) the light part yields a gasoline H/sub 2/O-soluble cut, a highly aromatic solvent fraction, a heavier cut (280/sup 0/ to 320/sup 0/) suitable as a plasticizer, and a phenol fraction. The heavier part of the tar is hydrogenated (at 380/sup 0/ and 400 atmospheres) to give spindle oil and lubricating oil of medium eta (11.2 centistokes at 98.2/sup 0/), moderate eta index (64), good pour point (-7/sup 0/), and good oxidizing characteristics. The overall yield of products from the two portions is 86.9% (gasoline and solvent 32, light phenols 9.7, spindle oil 14.2, medium lubricating oil 25.7, wax, 5.3%).

Radiation-thermal processes of conversion in the coals

International Nuclear Information System (INIS)

Mustafaev, I.I.

2002-01-01

Full text: The brief review, history, modern condition and bibliographic data on research of radiation-stimulated processes in coals are adduced in the report. Results of new researches of influence of gamma - radiation and accelerated electrons on pyrolysis, gasification, desulphurization, paramagnetism, adsorption and optical properties of coals in wide intervals of change of absorbed dose, dose rate, temperature, radiation type and other parameters of processes are stated. As object of researches Turkish (Yeni koy, Yatagan) and Russian (Siberia) coals were used. Specific peculiarities of influence of ionizing radiations on fossil fuels, bringing in change of their reactivity as result of destruction and polycondensation processes are considered. a)Pyrolysis: Under action of gamma-radiation and accelerated electrons the rate of thermal (t) pyrolysis grows and the ratio of radiation-thermal (rt) and thermal (t) processes: Wrt/ Wt depends on dose rate and temperature. By increase of dose rate the radiation effects grows, and at increase of temperature this effect is reduced. The influence of high rate heating of coals under pulls action of accelerated electrons on conversion degree and product composition has been established. The investigation regularities of formation liquid and gas products is resulted at radiation - thermal processing of mixtures of lignites with fuel oil. These experiments were conducted in flowing conditions in the interval of temperature T=350-500 degrees centigrade, power of the pulls accelerated electrons P=30-50 W, flow velocity of fuel oil 0,2-2 ml/minute. As a index of process were controlled conversion degree of coals, overall yield, contents and characteristic of liquid and gas products. The products of thermal treatment of these mixtures and also radiation-thermal treatment of separate components significantly less than radiation-thermal conversion of binary mixtures. It has been established that radiation effect has a positive

The application of Airborne Laser Scaning for identifying old lignite workings - case study: the mine "Borussia" near Ośno Lubuskie (Western Poland)

Science.gov (United States)

Gontaszewska-Piekarz, Agnieszka; Mrówczyńska, Maria

2018-04-01

The paper presents the possibilities of using data obtained by airborne laser scanning for identifying areas where lignite used to be mined. The technology of airborne laser scanning presented in the paper as and its results have a vast potential in terms of identifying local terrain deformations. The paper also presents the history of lignite mining in the region of Ośno Lubuskie (the north-west of Ziemia Lubuska - western Poland). It describes underground mining in complicated geological conditions (glaciotectonic deformations). The paper is supplemented with historical maps showing the locations of the mines

The Mineral Character and Geomechanical Properties of the Transitional Rocks from the Mesozoic-Neogene Contact Zone in the Bełchatów Lignite Deposit

Directory of Open Access Journals (Sweden)

Agnieszka Pękala

2014-01-01

Originality/value: Against the background of a number of published papers on the rocks accompanying lignite seams there is a lack of the "Bełchatów" mineralogical-petrographic studies of the transitional sediments in the Mesozoic-Neogene contact zone in the "Bełchatów" lignite deposit taking into account the aspect of raw materials. This paper has been produced to fill the void in this area.

Diagnostic measurements on the great machines conditions of lignite surface mines

Energy Technology Data Exchange (ETDEWEB)

Helebrant, F.; Jurman, J.; Fries, J. [Technical University of Ostrava, Ostrava-Poruba (Czech Republic)

2005-07-01

An analysis of the diagnosis of loading and service dependability of a rail-mounted excavator used in surface lignite mining is described. Wheel power vibrations in electric motor bearings and electric motor input bearings to the gearbox were measured in situ, in horizontal, vertical, and axial directions. The data were analyzed using a mathematical relationship. The results are presented in a loading diagram that shows the deterioration and the acceptable lower bound of machine conditions over time. Work is continuing. 5 refs., 1 fig.

Speciation of selected trace and major elements in lignite Used in "Nikola Tesla A" power plant (Obrenovac, Serbia

Directory of Open Access Journals (Sweden)

ALEKSANDAR POPOVIC

2005-12-01

Full Text Available Four samples of milled lignite used in the “Nikola Tesla A” power plant, located in Obrenovac near Belgrade, were subjected to a five-step sequential extraction, comprising of the following phases: distilled water, 1 M ammonium acetate, 0.2 M ammonium oxalate / 0.2 M oxalic acid, acidic solution of H2O2 and a 6 M solution of HCl. The concentrations of the different elements obtained in the extractions were statistically analysed. The majority of the examined elements were found to be most probably associated with inorganic fractions of lignite, only aluminum, silicon, chromium and arsenic have a larger extractable organic/sulfide fraction than an extractable inorganic fraction. Alumosilicates of magnesium (carriers of arsenic, zinc, lead, copper and chromium, silicates of potassium (scavengers of lead and nickel, mixed aluminates of iron and magnesium (carriers of arsenic, zinc, copper and chromium and compounds of iron that do not contain aluminum and magnesium (scavengers of manganese were dissolved in the fifth phase of the sequential extraction. Copper is a substrate of alumosilicates of potassium and magnesium, while zinc and chromium are substrates of compounds of iron leached in the third phase of the sequential extraction. Interphase correlation revealed that the adsorbed and ion-exchangeable fractions of most of the examined elements do not exhibit preferential binding to the components of the inorganic matrix of lignite ash.

Environmental assessment of remedial action at the inactive uraniferous lignite ashing sites at Belfield and Bowman, North Dakota

International Nuclear Information System (INIS)

1993-09-01

The Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978 authorized the US Department of Energy (DOE) to perform remedial actions at Belfield and Bowman inactive lignite ashing sites in southwestern North Dakota to reduce the potential public health impacts from the residual radioactivity remaining at the sites. The US Environmental Protection Agency (EPA) promulgated standards (40 CFR 192) that contain measures to control the residual radioactive materials and other contaminated materials, and proposed standards to protect the groundwater from further degradation. Remedial action at the Belfield and Bowman sites must be performed in accordance with these standards and with the concurrence of the US Nuclear Regulatory Commission (NRC) and the state of North Dakota. The Belfield and Bowman designated sites were used by Union Carbide and Kerr-McGee, respectively, to process uraniferous lignite in the 1960s. Uranium-rich ash from rotary kiln processing of the lignite was loaded into rail cars and transported to uranium mills in Rifle, Colorado, and Ambrosia Lake, New Mexico, respectively. As a result of the ashing process, there is a total of 158,400 cubic yards (yd 3 ) [121,100 cubic meters (m 3 )] of radioactive ash-contaminated soils at the two sites. Windblown ash-contaminated soil covers an additional 21 acres (8.5 ha) around the site, which includes grazing land, wetlands, and a wooded habitat

Effects of vesicular-arbuscular mycorrhizae on survival and growth of perennial grasses in lignite overburden in Texas

Energy Technology Data Exchange (ETDEWEB)

Call, C.A.; Davies, F.T.

1988-12-01

Seedlings of sideoats grama (Bouteloua curtipendula), Indiangrass (Sorghastrum nutans), and kleingrass (Panicum coloratum) were inoculated with vesicular-arbuscular mycorrhizal (VAM) fungi (Glomus fasciculatum and Gigaspora margarita) in a containerized system and transplanted into lignite overburden in the Post Oak Savannah region of Texas, U.S.A. After three growing seasons without cultural inputs, plants inoculated with VAM fungi had greater survival percentages, basal diameters, and above-ground biomass than noninoculated plants. Inoculated plants had higher levels of nitrogen and phosphorus in above-ground biomass than noninoculated plants. Root colonization percentages of inoculated plants remained fairly stable while noninoculated plants showed low levels of colonization over the 3-year study period. Vesicular-arbuscular mycorrhizae enhanced the survival and growth of the 3 grass species by making effective use of limited resources in the lignite overburden. 31 refs., 3 tabs.

Catalytic effect of lignite ash on steam gasification of oil sand coke

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E.; Palmer, A.

1986-06-16

Steam gasification of Suncor and Syncrude cokes was carried out in the presence of ash obtained after burning Onakawana lignite. Catalytic effects of the ash were evident at 930 C whereas at 830 C little effect was observed. These observations were attributed to the combined actions of Ca- and Fe-containing species in the ash, in which the former neutralized the sulfur in the cokes to prevent poisoning of Fe oxides. 5 tabs., 5 figs., 15 refs.

Catalytic effect of mineral matter of high ash Onakawana lignite on steam gasification

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E.

1986-04-01

Reactivities of untreated and acid washed Onakawana lignite during steam gasification were compared in a thermobalance reactor. The acid treatment resulted in removal of Ca, Mg, Ba and Sr from mineral matter. This was accompanied by a marked decrease in the rates of H/sub 2/, CO and CO/sub 2/ formation. The decrease of gasification rate was attributed to the decrease in concentration of gasification sites during the acid treatment.

Evaluation of radioactive emissions of lignite-fired power plants in Turkey using the Analytic Hierarchy Process

Energy Technology Data Exchange (ETDEWEB)

Bueke, Tayfun [Mugla Sitki Kocman Univ., Mugla (Turkey). Dept. of Energy Systems Engineering

2013-11-15

Radioactive emissions of 13 lignite-fired power plants in Turkey are of great concern to the public and to scientists alike. The purpose of this study is to evaluate these power plants, according to their radioactive emissions by using the Analytic Hierarchy Process. Control criteria are in particular {sup 226}Ra, {sup 232}Th, {sup 40}K and {sup 238}U emissions from the power plants. These control criteria are weighted according to the objective assessment. The calculations are repeated for three different objective assessments of control criteria namely the mortality risk coefficients for inhalation, ingestion, external exposure of {sup 226}Ra, {sup 232}Th, {sup 40}K and {sup 238}U. It has been calculated that the Can lignite-fired power plant is ranking first while the Soma-B plant is ranking last according to the radioactive emissions of the power plants when the average of three different objective control criteria are used in the calculations. (orig.)

Effectiveness of thermal annular procedures in treating discogenic low back pain.

Science.gov (United States)

Helm Ii, Standiford; Deer, Timothy R; Manchikanti, Laxmaiah; Datta, Sukdeb; Chopra, Pradeep; Singh, Vijay; Hirsch, Joshua A

2012-01-01

Persistent low back pain refractory to conservative treatment is a common problem that leads to widespread impairment, resulting in significant costs to society. The intervertebral disc is a major source of persistent low back pain. Technologies developed to treat this problem, including various surgical instrumentation and fusion techniques, have not reliably provided satisfactory results in terms of either pain relief or increased function. Thermal annular procedures (TAPs) were first developed in the late 1990s in an attempt to treat discogenic pain. The hope was that they would provide greater value than fusion in terms of efficacy, morbidity, and cost. Three technologies have been developed to apply heat to the annulus: intradiscal electrothermal therapy (IDET), discTRODE, and biacuplasty. Since nerve ingrowth and tissue regeneration in the annulus is felt to be the source of pain in discogenic low back pain, when describing the 3 above techniques we use the term "thermal annular procedures" rather than "thermal intradiscal procedures." We have specifically excluded studies treating the nucleus. TAPs have been the subject of significant controversy. Multiple reviews have been conducted resulting in varying conclusions. A systematic review of TAPs for the treatment of discogenic low back pain. To evaluate the effectiveness of TAPs in treating discogenic low back pain and to assess complications associated with those procedures. The available literature on TAPs in treating discogenic low back pain was reviewed. The quality assessment and clinical relevance criteria utilized were the Cochrane Musculoskeletal Review Group criteria for interventional techniques for randomized trials, and the criteria developed by the Newcastle-Ottawa Scale criteria for observational studies. The level of evidence was classified as good, fair, or poor based on the quality of evidence developed by the U.S. Preventive Services Task Force. Data sources included relevant literature

Valorization of lignite combustion residues and ferroalumina in the production of aggregates.

Science.gov (United States)

Anagnostopoulos, I M; Stivanakis, V E; Angelopoulos, G N; Papamantellos, D C

2010-02-15

The present research study investigates the synergy of industrial solid by-products from lignite combustion (fly ash and bottom ash) and aluminum production (ferroalumina) in the production of lightweight aggregates (LWA). The process consists of two stages, pelletization and sintering. Bottom ash (BA) is used as the principal raw material in mixtures while ferroalumina (FAL) is added in lower percentages (5-30 wt%). BA carbon content is used as the fuel of sintering process in high temperatures, around 1250 degrees C, and gas generation is responsible for porous structure formation. Physical properties such as porosity, water absorption and bulk density, of sintering products are measured. Increase of FAL percentage in sintering mixtures results in decrease of porosity from 61% to 35% and of water absorption from 61% to 21% and in increase of bulk density from 1.02 g/cm(3) to 1.80 g/cm(3) of the produced aggregates. Aggregates produced by FAL addition up to 20 wt% are characterized as LWA. Aggregates formed are used in the production of concrete specimens. Compressive strength of concrete increases by increasing FAL addition in aggregates from 5 wt% to 15 wt% (highest strength value), while decrease by increasing FAL addition from 20 wt% to 30 wt%. FAL addition in lignite ashes sintering mixtures (up to 15 wt%) is considered as an important parameter for enhancing aggregates strength.

Nutrients and heavy metal distribution in thermally treated pig manure

DEFF Research Database (Denmark)

Kuligowski, Ksawery; Poulsen, Tjalfe G.; Stoholm, Peder

2008-01-01

Ash from pig manure treated by combustion and thermal gasification was characterized and compared in terms of nutrient, i.e., potassium (K), phosphorus (P) and heavy metal, i.e., cadmium (Cd), chromium (Cr), copper (Cu), nickel (Ni) and zinc (Zn) contents. Total nutrient and metal concentrations...... that ash from gasified manure contained more water-extractable K in comparison with combusted manure whereas the opposite was the case with respect to P. Heavy metals Ni, Cr and Cd were present in higher concentrations in the fine particle size fractions (

Lignite and hard coal: Energy suppliers for world needs until the year 2100 - An outlook

International Nuclear Information System (INIS)

Thielemann, Thomas; Schmidt, Sandro; Peter Gerling, J.

2007-01-01

For three years, international hard coal prices have been at rather expensive levels. Some argue that these higher prices might indicate the threat of a physical scarcity of fossil fuels - similar to the situation with oil and gas. This is not true. The supply situations with lignite and hard coal appear to be largely not critical. Adjusted to the rise in global coal consumption, which is expected until 2100, nature by and large can meet the world's coal demand. This is shown for lignite in this article and it is illustrated for hard coal here, differentiated in space and time for a world divided into eight regions and viewed for the years 2005, 2020, 2030, 2050, and 2100. The only area of potential concern is Asia (especially China). But today's and coming eager efforts in China to convert coal resources into reserves will most likely deliver the coal needed for the Chinese market. Up to the year 2100, and from a geoscientific point of view, there will be no bottleneck in coal supplies on this planet. (author)

Low temperature coal depolymerization-liquefaction: conversion of a North Dakota lignite to a light hydrocarbon oil

Energy Technology Data Exchange (ETDEWEB)

Shabtai, J.; Yuan Zhang (University of Utah, Salt Lake City, UT (USA). Dept. of Fuels Engineering)

1989-10-01

A new low temperature method of coal liquefaction is described which includes intercalation of the coal with FeCl{sub 3}, depolymerization under supercritical conditions, and hydroprocessing of the depolymerized product. Results indicate a high yield conversion of lignites to light hydrocarbon oils. 6 refs., 4 figs., 1 tab.

Co-processing of lignite-plastic mixtures into liquid distillate fractions in the presence of iron catalysts

Energy Technology Data Exchange (ETDEWEB)

Kuznetsov, B.N.; Sharypov, V.I.; Beregovtsova, N.G.; Baryshnikov, S.V.; Doroginskaya, A.N. [Russian Academy of Sciences, Krasnoyarsk (Russian Federation). Inst. of Chemistry of Natural Organic Materials Sibirian Branch

1997-12-31

Some features of co-processing of Kansk-Achinsk lignite with plastics into hydrocarbon mixtures in the presence of activated iron-containing minerals (hematite, magnetite, pyrrhotite) were investigated under various operating parameters. The following catalytic processes were studied: pyrolysis in an inert atmosphere, hydropyrolysis and water-steam cracking. (orig.)

Use of lignite in the production of sponge iron and processing of waste oxides in rotary kilns

Energy Technology Data Exchange (ETDEWEB)

Eichberger, H; Schnabel, W; Serbent, H

1978-11-01

Based on a study of the situation of fossil energy reserves, processes are described in which non-coking coals, in particular lignite, are used for reduction in the rotary kiln, i.e. for sponge iron production and for zinc volatilization from waste oxides).

Land movement monitoring at the Mavropigi lignite mine using spaceborne D-InSAR

Science.gov (United States)

Papadaki, Eirini; Tripolitsiotis, Achilleas; Steiakakis, Chrysanthos; Agioutantis, Zacharias; Mertikas, Stelios; Partsinevelos, Panagiotis; Schilizzi, Pavlos

2013-08-01

This paper examines the capability of remote sensing radar interferometry to monitor land movements, as it varies with time, in areas close to open pit lignite mines. The study area is the "Mavropigi" lignite mine in Ptolemais, Northern Greece; whose continuous operation is of vital importance to the electric power supply of Greece. The mine is presently 100-120m deep while horizontal and vertical movements have been measured in the vicinity of the pit. Within the mine, ground geodetic monitoring has revealed an average rate of movement amounting to 10-20mm/day at the southeast slopes. In this work, differential interferometry (DInSAR), using 19 Synthetic Aperture Radar (SAR) images of ALOS satellite, has been applied to monitor progression of land movement caused my mining within the greater area of "Mavropigi" region. The results of this work show that DInSAR can be used effectively to capture ground movement information, well before signs of movements can be observed visually in the form of imminent fissures and tension cracks. The advantage of remote sensing interferometry is that it can be applied even in inaccessible areas where monitoring with ground equipment is either impossible or of high-cost (large areas).

Polarized neutron reflectivity study of a thermally treated MnIr/CoFe exchange bias system.

Science.gov (United States)

Awaji, Naoki; Miyajima, Toyoo; Doi, Shuuichi; Nomura, Kenji

2010-12-01

It has recently been found that the exchange bias of a MnIr/CoFe system can be increased significantly by adding a thermal treatment to the bilayer. To reveal the origin of the higher exchange bias, we performed polarized neutron reflectivity measurements at the JRR-3 neutron source. The magnetization vector near the MnIr/CoFe interface for thermally treated samples differed from that for samples without the treatment. We propose a model in which the pinned spin area at the interface is extended due to the increased roughness and atomic interdiffusion that result from the thermal treatment.

Selective coal mining of intercalated lignite deposits

Energy Technology Data Exchange (ETDEWEB)

Zunic, R [Kolubara-Projekt, Lazarevac (Yugoslavia)

1991-01-01

Describes selective coal mining in the Tamnava-Istocno Polje coal surface coal mine (Yugoslavia), designed for an annual coal production of 11.4 Mt. Until 1991, this mine exploited one thick lignite seam, without spoil intercalations, using a bucket wheel excavator-conveyor-spreader system both for coal mining and removal of overburden. In the future, several spoil intercalations of up to 1.0 m and thicker will appear with a total volume of 22 million m{sup 3}. These intercalations have to be selectively excavated in order to guarantee the calorific value of coal for the Nikola Tesla power plant. Computer calculations were carried out to determine the decrease in excavator coal production due to selective mining of spoil strata. Calculations found that the annual surface mine capacity will be lower by at most 9%, depending on thickness of spoil intercalations. The useful operation time of excavators will be reduced by 98 hours per year. The planned annual coal production will nevertheless be fulfilled. 3 refs.

Late Neogene leaf assemblage from Bełchatów Lignite Mine (central Poland

Directory of Open Access Journals (Sweden)

Worobiec Grzegorz

2014-12-01

Full Text Available Leaf macroremains collected in the Bełchatów Lignite Mine (central Poland were investigated. The fossil assemblage consists of leaves of Acer, Betula, Carpinus, Dicotylophyllum, Fagus, ?Magnolia, “Parrotia”, Pinus, Quercus, and Zelkova. Mesophytic (zonal elements dominate, with admixture of riparian (azonal leaf taxa. The floristic composition points to late Neogene (late Miocene to late Pliocene age and suggests favourable temperate climate with mild winters.

Speciation of selected trace and major elements in lignite used in 'Nikola Tesla A' power plant (Obrenovac, Serbia)

Energy Technology Data Exchange (ETDEWEB)

Aleksandar Popovic; Dragana Djordjevic [University of Belgrade, Belgrade (Serbia and Montenegro). Department of Chemistry

2005-07-01

Four samples of milled lignite used in the 'Nikola Tesla A' power plant, located in Obrenovac near Belgrade, were subjected to a five-step sequential extraction, comprising of the following phases: distilled water, 1 M ammonium acetate, 0.2 M ammonium oxalate/0.2 M oxalic acid, acidic solution of H{sub 2}O{sub 2} and a 6 M solution of HCl. The concentrations of the different elements obtained in the extractions were statistically analysed. The majority of the examined elements were found to be most probably associated with inorganic fractions of lignite, only aluminum, silicon, chromium and arsenic have a larger extractable organic/sulfide fraction than an extractable inorganic fraction. Alumosilicates of magnesium (carriers of arsenic, zinc, lead, copper and chromium), silicates of potassium (scavengers of lead and nickel), mixed aluminates of iron and magnesium (carriers of arsenic, zinc, copper and chromium) and compounds of iron that do not contain aluminum and magnesium (scavengers of manganese) were dissolved in the fifth phase of the sequential extraction. Copper is a substrate of alumosilicates of potassium and magnesium, while zinc and chromium are substrates of compounds of iron leached in the third phase of the sequential extraction. Interphase correlation revealed that the adsorbed and ion-exchangeable fractions of most of the examined elements do not exhibit preferential binding to the components of the inorganic matrix of lignite ash.

Device for determining element contents of lignite mass flows by activation analysis

International Nuclear Information System (INIS)

Goeldner, R.; Maul, E.; Rose, W.; Wagner, D.

1987-01-01

A simple device is presented, apt for continuous operation, to determine the element contents of bulk goods of flowable materials with a suitable granularity, in particular of lignite mass flows to assess the coal quality. Several kilograms of samples can be reproducibly dosed and homogeneously activated by a device consisting of a shielding container with activation chamber and radiation source, a measuring unit with detectors, and a source container, and characterized by a blade wheel in the activation chamber which causes the dosing and homogeneous activation of the sample

Lignite air-steam gasification in the fluidized bed of iron-containing slag catalysts

Energy Technology Data Exchange (ETDEWEB)

Kuznetsov, B.N.; Shchipko, M.L.; Golovin, Yu. [Inst. of Chemistry of Natural Organic Materials, Academgorodok, Krasnoyarsk (Russian Federation)

1995-12-01

The influence of fluidized bed of iron-containing slag particles on air-steam gasification of powdered Kansk-Achinsk lignite in entrained flow was studied in pilot installation with productivity about 60 kg per hour. Slag of Martin process and boiler slag were used as catalytic active materials until their complete mechanical attrition. Two following methods of catalytic gasification of lignite were compared: the partial gasification in stationary fluidized bed of slag particles with degree of fuel conversion 40-70% and complete gasification in circulating bed of slag particles. In the first case only the most reactive part of fuel is gasified with the simultaneously formation of porous carbon residue with good sorption ability. It was found the catalytic fluidized bed improves heat transfer from combustion to reduction zone of gas-generator and increases the rate of fuel conversion at the temperature range 900-1000{degrees}C. At these temperatures the degree of conversion is depended considerably on the duration time of fuel particles in the catalytic fluidized bed. The influence of catalytic fluidized bed height and velocity of reaction mixture on the temperature profiles in the gas-generator was studied. The optimal relationship was found between the fluidized bed height and velocity of flow which makes possible to produce the gas with higher calorific value at maximum degree of fuel conversion.

Environmental policy instruments towards lignite-fired power plants in Turkey

International Nuclear Information System (INIS)

2006-01-01

A proposition is made that Turkey considers a pilot emission trading system for SO 2 , Nox and/or PM emissions from its coal and lignite fired power plant in the efforts to comply with the EU Integrated Pollution Prevention Control (IPPC), the Large Combustion Plant (LCP) and the National Emissions Ceiling (NEC) Directives. Model calculations indicate that this could yield substantial cost savings compared to a traditional command and control approach. However, requirements in the IPPC Directive would be a major obstacle against emissions trading. The Turkish emission permitting system needs a major overhaul, including improving monitoring and enforcement practices to comply with the directives and to be able to implement and operate an emission trading system

Environmental policy instruments towards lignite-fired power plants in Turkey

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-07-01

A proposition is made that Turkey considers a pilot emission trading system for SO{sub 2}, Nox and/or PM emissions from its coal and lignite fired power plant in the efforts to comply with the EU Integrated Pollution Prevention Control (IPPC), the Large Combustion Plant (LCP) and the National Emissions Ceiling (NEC) Directives. Model calculations indicate that this could yield substantial cost savings compared to a traditional command and control approach. However, requirements in the IPPC Directive would be a major obstacle against emissions trading. The Turkish emission permitting system needs a major overhaul, including improving monitoring and enforcement practices to comply with the directives and to be able to implement and operate an emission trading system.

Bucket wheel excavator performances at Neyveli lignite mine

Energy Technology Data Exchange (ETDEWEB)

Kumaraswamy, S; Mozumdar, B K

1987-03-01

Bucket-wheel excavators have been in use at the Neyveli Lignite Mine in the State of Tamil Nadu, India, since the early nineteen-sixties. The mining environment has been particularly harsh for BWE application. The adverse influencing factors are the hardness of the over-burden formation, high abrasivity of rock and artesian ground water conditions. In this paper, the performances of the BWEs at Neyveli have been statistically analysed to determine the effects of physico-mechanical properties of overburden, blasting and rainfall on machine productivity, availability, wear-and-tear of bucket teeth, power consumption, production efficiency and cost of mining. An empirical relationship between the production efficiency, defined as the ratio of actual production rate to the theoretical one, and the bench height and width, height of slices, specific cutting resistance of the overburden material and its clay content, consumption of explosives, and conveyor length has been established.

Research of lignite oxidation kinetic parameters modified by CuSO4 and NaNO3 initiation additives

Directory of Open Access Journals (Sweden)

Larionov Kirill

2017-01-01

Full Text Available An experimental study and subsequent analytical assessment of activation energy change in lignite oxidation process with addition of NaNO3 and CuSO4 mineral salts were conducted. The results showed that injection of catalytic additives leads to reduction of coal activation energy and reaction initial temperature.

REMOVAL OF Cr(VI FROM AQUEOUS SOLUTION BY ACTIVATED COAL FROM LIGNITE COAL

Directory of Open Access Journals (Sweden)

Mehmet MAHRAMANLIOĞLU

2001-03-01

Full Text Available Activated coal produced from Ağaçlı Lignite coal was used to remove Cr(VI from aqueous solutions. The adsorption of Cr(VI was studied as a function of initial concentration, time, pH, adsorbent concentration and temperature. The adsorption data were found to fit to Langmuir and Freundlich isotherms. Lagergren equation was used to calculate the adsorption rate. The amount of Cr(VI adsorbed was increased with decreasing pH and decreased with increasing temperature.

Modernisation of a lignite-fired steam generator. Reduction of NO{sub x} emission

Energy Technology Data Exchange (ETDEWEB)

Kriegeskotte, Ralf; Thierbach, Hans-Ulrich; Zimmermann, Bernhard [Steinmueller Engineering GmbH, Gummersbach (Germany); Di Ferdinando, Quinto [ContourGlobal Maritsa East 3 AD, Sofia (Bulgaria)

2013-11-01

ContourGlobal Maritsa East 3 is a lignite-fired power plant with an electrical total output of 4 x 227 MW. The four steam generators of Russian design have a steam capacity up to 730 t/h each and were commissioned between 1978 and 1981. According to EU requirements, the NO{sub x} emissions have to be reduced reliably by 2015. The consortium Steinmueller Engineering GmbH Gummersbach and Siemens EOOD, Sofia, successfully redesigned the furnace of boiler 4. (orig.)

An ecosystem approach to evaluate restoration measures in the lignite mining district of Lusatia/Germany

Science.gov (United States)

Schaaf, Wolfgang

2015-04-01

Lignite mining in Lusatia has a history of over 100 years. Open-cast mining directly affected an area of 1000 km2. Since 20 years we established an ecosystem oriented approach to evaluate the development and site characteristics of post-mining areas mainly restored for agricultural and silvicultural land use. Water and element budgets of afforested sites were studied under different geochemical settings in a chronosequence approach (Schaaf 2001), as well as the effect of soil amendments like sewage sludge or compost in restoration (Schaaf & Hüttl 2006). Since 10 years we also study the development of natural site regeneration in the constructed catchment Chicken Creek at the watershed scale (Schaaf et al. 2011, 2013). One of the striking characteristics of post-mining sites is a very large small-scale soil heterogeneity that has to be taken into account with respect to soil forming processes and element cycling. Results from these studies in combination with smaller-scale process studies enable to evaluate the long-term effect of restoration measures and adapted land use options. In addition, it is crucial to compare these results with data from undisturbed, i.e. non-mined sites. Schaaf, W., 2001: What can element budgets of false-time series tell us about ecosystem development on post-lignite mining sites? Ecological Engineering 17, 241-252. Schaaf, W. and Hüttl, R. F., 2006: Direct and indirect effects of soil pollution by lignite mining. Water, Air and Soil Pollution - Focus 6, 253-264. Schaaf, W., Bens, O., Fischer, A., Gerke, H.H., Gerwin, W., Grünewald, U., Holländer, H.M., Kögel-Knabner, I., Mutz, M., Schloter, M., Schulin, R., Veste, M., Winter, S. & Hüttl, R.F., 2011: Patterns and processes of initial terrestrial-ecosystem development. Journal of Plant Nutrition and Soil Science, 174, 229-239. Schaaf, W., Elmer, M., Fischer, A., Gerwin, W., Nenov, R., Pretsch, H. and Zaplate, M.K., 2013: Feedbacks between vegetation, surface structures and hydrology

Using kinetic models to predict thermal degradation of fire-retardant-treated plywood roof sheathing

Science.gov (United States)

Patricia Lebow; Jerrold E. Winandy; Patricia K. Lebow

2003-01-01

Between 1985-1995 a substantial number of multifamily housing units in the Eastern and Southern U.S. experienced problems with thermally degraded fire-retardant-treated (FRT) plywood roof sheathing. A series of studies conducted at the USDA Forest Service, Forest Products Laboratory (FPL), examined the materials, chemical mechanisms, and process implications and has...

Impact of an angiotensin analogue in treating thermal and combined radiation injuries

Science.gov (United States)

Jadhav, Sachin Suresh

Background: In recent years there has been a growing concern regarding the use of nuclear weapons by terrorists. Such incidents in the past have shown that radiation exposure is often accompanied by other forms of trauma such as burns, wounds or infection; leading to increased mortality rates among the affected individuals. This increased risk with combined radiation injury has been attributed to the delayed wound healing observed in this injury. The Renin-Angiotensin System (RAS) has emerged as a critical regulator of wound healing. Angiotensin II (A-II) and Angiotensin (1-7) [A(1-7)] have been shown to accelerate the rate of wound healing in different animal models of cutaneous injury. Nor-Leu3-Angiotensin (1-7) [Nor-Leu3-A (1-7)], an analogue of A(1-7), is more efficient than both A-II and A(1-7) in its ability to improve wound healing and is currently in phase III clinical trials for the treatment of diabetic foot ulcers. Aims: The three main goals of this study were to; 1) Develop a combined radiation and burn injury (CRBI) model and a radiation-induced cutaneous injury model to study the pathophysiological effects of these injuries on dermal wound healing; 2) To treat thermal and CRBI injuries using Nor-Leu 3-A (1-7) and decipher the mechanism of action of this peptide and 3) Develop an in-vitro model of CRBI using dermal cells in order to study the effect of CRBI on individual cell types involved in wound healing. Results: CRBI results in delayed and exacerbated apoptosis, necrosis and inflammation in injured skin as compared to thermal injury by itself. Radiation-induced cutaneous injury shows a radiation-dose dependent increase in inflammation as well as a chronic inflammatory response in the higher radiation exposure groups. Nor-Leu3-A (1-7) can mitigate thermal and CRBI injuries by reducing inflammation, oxidative stress and DNA damage while increasing the rate of proliferation of dermal stem cells and re-epithelialization of injured skin. The in

Reclamation of a lignite combustion waste disposal site with alders (Alnus sp.): assessment of tree growth and nutrient status within 10 years of the experiment.

Science.gov (United States)

Pietrzykowski, Marcin; Woś, Bartłomiej; Pająk, Marek; Wanic, Tomasz; Krzaklewski, Wojciech; Chodak, Marcin

2018-06-01

Combustion wastes are characterised by extremely low N contents. Therefore, introduction of nitrogen-fixing species at the first stage of their biological reclamation is required. This paper presents an assessment of the growth parameters of alders (Alnus sp.) 10 years after their introduction to a disposal site of lignite combustion waste in Central Poland. Black (Alnus glutinosa) and grey alders (Alnus incana) were planted directly in the combustion waste. The soil amendment included three variants: control with pure combustion waste, admixture of lignite culm and addition of acid sand. Both alder species displayed good growth parameters comparable to those of alders in natural habitats. However, black alder had better growth parameters, such as stand density index (SDI), diameter at breast height (DBH) and height (H) than grey alder. The lignite amendment exerted a positive effect on tree growth, reflected in a higher SDI and H, whereas the acid sand amendment did not affect any of the growth parameters of the studied alder species. Despite the good growth parameters, the measured N:P and N:K ratios in the alder leaves largely differed from the optimal values indicating insufficient P and K supply at the combustion waste disposal site. This may pose a threat to further development of the introduced tree plantings. The introduction of alders along with the lignite addition into the planting holes seems to be a successful method of combustion waste revegetation.

[Gradient elevation of temperature startup experiment of thermophilic ASBR treating thermal-hydrolyzed sewage sludge].

Science.gov (United States)

Ouyang, Er-Ming; Wang, Wei; Long, Neng; Li, Huai

2009-04-15

Startup experiment was conducted for thermophilic anaerobic sequencing batch reactor (ASBR) treating thermal-hydrolyzed sewage sludge using the strategy of the step-wise temperature increment: 35 degrees C-->40 degrees C-->47 degrees C-->53 degrees C. The results showed that the first step-increase (from 35 degrees C to 40 degrees C) and final step-increase (from 47 degrees C to 53 degrees C) had only a slight effect on the digestion process. The second step-increase (from 40 degrees C to 47 degrees C) resulted in a severe disturbance: the biogas production, methane content, CODeffluent and microorganism all have strong disturbance. At the steady stage of thermophilic ASBR treating thermal-hydrolyzed sewage sludge, the average daily gas production, methane content, specific methane production (CH4/CODinfluent), TCOD removal rate and SCOD removal rate were 2.038 L/d, 72.0%, 188.8 mL/g, 63.8%, 83.3% respectively. The results of SEM and DGGE indicated that the dominant species are obviously different at early stage and steady stage.

Tanacetum vulgare as a bioindicator of trace-metal contamination: a study of a naturally colonized open-pit lignite mine.

Science.gov (United States)

Jasion, Mateusz; Samecka-Cymerman, Aleksandra; Kolon, Krzysztof; Kempers, Alexander J

2013-10-01

We investigated the possibility of use of Tanacetum vulgare (tansy) as an ecological indicator of metal concentration in a naturally colonized open-pit lignite mine in Bełchatów (Poland). Tanacetum vulgare is the only species growing abundantly and spontaneously in the lignite mine waste dumps. Metal concentrations in roots, stems, leaves, flowers, and soil were measured in dump sites differing in type and time of reclamation and therefore differing in pollution levels. Tanacetum vulgare appeared to be an accumulator of chromium and iron in roots, whereas highest concentrations of manganese and zinc were found in leaves. A high bioaccumulation factor for cadmium (Cd) was observed in dumps and control sites, indicating that even small amounts of Cd in the environment may result in significant uptake by the plant. The lowest concentrations of metals were found in plants from sites situated on dumps reclaimed with argillaceous limestone.

Effect of various experimental parameters on the swelling and supercritical extraction properties of lignite

Energy Technology Data Exchange (ETDEWEB)

Hacimehmetoglu, S.; Sinag, A.; Tekes, A.T.; Misirlioglu, Z.; Canel, M. [Ankara University, Ankara (Turkey). Faculty of Science

2007-07-01

The original lignite sample, the samples swollen in dimethylsulfoxide (DMSO), dimethylformamide (DMF), pyridine, tetrahydrofuran (THF), acetone, ethylenediamine (EDA), N-methyl-2-pyrrolidone (NMP), tetrabutylammonium hydroxide (TBAH), the samples impregnated by ZnCl{sub 2} as catalyst and the samples both swollen in the solvents and impregnated by ZnCl{sub 2} were subjected to the supercritical toluene extraction and the effects of temperature, pressure, pre-swelling procedure, hydrogen donor solvent (tetralin), and catalyst on the extract yields were investigated.

JV Task 106 - Feasibility of CO2 Capture Technologies for Existing North Dakota Lignite-Fired Pulverized Coal Boilers

Energy Technology Data Exchange (ETDEWEB)

Michael L. Jones; Brandon M. Pavlish; Melanie D. Jensen

2007-05-01

The goal of this project is to provide a technical review and evaluation of various carbon dioxide (CO{sub 2}) capture technologies, with a focus on the applicability to lignite-fired facilities within North Dakota. The motivation for the project came from the Lignite Energy Council's (LEC's) need to identify the feasibility of CO{sub 2} capture technologies for existing North Dakota lignite-fired, pulverized coal (pc) power plants. A literature review was completed to determine the commercially available technologies as well as to identify emerging CO{sub 2} capture technologies that are currently in the research or demonstration phase. The literature review revealed few commercially available technologies for a coal-fired power plant. CO{sub 2} separation and capture using amine scrubbing have been performed for several years in industry and could be applied to an existing pc-fired power plant. Other promising technologies do exist, but many are still in the research and demonstration phases. Oxyfuel combustion, a technology that has been used in industry for several years to increase boiler efficiency, is in the process of being tailored for CO{sub 2} separation and capture. These two technologies were chosen for evaluation for CO{sub 2} separation and capture from coal-fired power plants. Although oxyfuel combustion is still in the pilot-scale demonstration phase, it was chosen to be evaluated at LEC's request because it is one of the most promising emerging technologies. As part of the evaluation of the two chosen technologies, a conceptual design, a mass and energy balance, and an economic evaluation were completed.

Increase in extraction yields of coals by water treatment: Beulah-Zap lignite

Energy Technology Data Exchange (ETDEWEB)

Masashi Iino; Toshimasa Takanohashi; Takahiro Shishido; Ikuo Saito; Haruo Kumagai [National Institute of Advanced Industrial Science and Technology, Tsukuba (Japan)

2007-01-15

In a previous paper, we have reported that water pretreatments of Argonne premium coals, Pocahontas No. 3 (PO), Upper Freeport (UF), and Illinois No. 6 (IL) at 600 K increased greatly the room-temperature extraction yields with a 1:1 carbon disulfide/N-methyl-2-pyrrolidinone (CS{sub 2}/NMP) mixed solvent. In this paper, the water treatment of Beulah-Zap (BZ) lignite has been carried out and the results obtained were compared with those for the three bituminous coals above. The extraction yields of BZ with CS{sub 2}/NMP increased from 5.5% for the raw coal to 21.7% by the water treatment at 600 K. Similar to the other three coals, the water treatments at 500 K gave little increase in the yields. The larger decrease in oxygen content and hydrogen-bonded OH and the increase in the methanol swelling ratio by the water treatment suggest that the yield enhancements for BZ are attributed to the removal of oxygen functional groups and the breaking of hydrogen bonds to a greater extent than that for IL. From the characterizations of the treated coals and the extraction temperature dependency of their extraction yields, it is suggested that, for high-coal-rank coals, PO and UF, the breaking of noncovalent bonds such as {pi}-{pi} interactions between aromatic layers and hydrogen bonds is responsible for the extraction yield enhancements. 14 refs., 3 figs., 2 tabs.

Adsorption study of mercury on lignite in the presence of different anions

Directory of Open Access Journals (Sweden)

Irma Robles

2016-05-01

Full Text Available This study compares the effect of different anions such as chloride, nitrate, and sulphate on the mercury adsorption onto lignite, which was a model material for the humus-containing organics in soil, and can be considered as a natural sorbent in the remediation of contaminated sites. Since the complex formation can significantly influence the mercury sorption, besides chloride, the effects of other complex-forming agents such as ethylenediaminetetraacetic acid, and thiocyanate were also tested. Various batch type and dynamic experiments were performed and four sorption models (Langmuir, Freundlich, Temkin and Dubinin-Radushkevich were used to evaluate the sorption data.

Adsorption of manganese(II) ions by EDTA-treated activated carbons

Energy Technology Data Exchange (ETDEWEB)

Khan, A.Y.; Mazyck, D.W. [Jones Edmunds & Associates, Gainesville, FL (United States)

2009-07-01

The adsorption of manganese(II) ions from aqueous solution onto three different granular activated carbons treated with ethylenediamine tetraacetic acid (EDTA) and its sodium salt was investigated. Characterization of the chelate-treated carbons showed that EDTA altered the physical and chemical properties of the sorbents relative to their untreated counterparts. Furthermore, the modified sorbents exhibited a heightened capacity towards the adsorption of Mn(II) ions from aqueous media. Manganese(II) ion removal increased from 0 to 6.5 mg/g for the lignite coal-based sorbent, from 3.5 to 14.7 mg/g for the wood-based sorbent and from 1.3 to 7.9 mg/g for the bituminous coal-based sorbent. The increased removal is attributed, in part, to the creation of Lewis base sites that participate in covalent interactions and hydrolysis reactions.

Resistance of polyvinyl alcohol blends stabilized by sodium and ammonium salts of lignite humic acids against γ-irradiation

International Nuclear Information System (INIS)

Barbora Bakajova; Jiri Kucerik; Michal Ilcin; Oga Hola

2011-01-01

The dried blends containing sodium and ammonium salts of lignite humic acids (humates, 0.5-10% w/w) in polyvinyl alcohol (PVA) were exposed to high dosage of γ-irradiation in the range of doses 127-806 kGy. Resulted products were then tested for their stability using thermogravimetrical analysis. As a reference the non-treated blends were used since the pure PVA exposed to γ-irradiation very quickly lost its stability and resulting consistence did not allow the stability tests. Stabilities showed a strong concentration and counterion dependency. While sodium counterion caused mostly destabilization with increasing dose, the ammonium counterion acted in an opposite way. The tests carried out in a moisturizing container revealed the changes in water absorbing capacity of irradiated samples and allowed partial explanation of humate stabilizing effect. Generally, at lower concentration of a humate the increase was observed with an increase in the γ-irradiation dose and vice versa. The results confirmed the antioxidant and stabilizing effect of humic acids added to some synthetic polymers and their applicability in materials exposed to γ-irradiation. (author)

Chemical mass balance source apportionment of TSP in a lignite-burning area of Western Macedonia, Greece

Science.gov (United States)

Samara, Constantini

Total suspended particle mass concentrations (TSP) were determined in the Kozani-Ptolemais-Florina basin (western Macedonia, Greece), an area with intensive lignite burning for power generation. The study was conducted over a 1-year period (November 2000-November 2001) at 10 receptor sites located at variable distances from the power plants. Ambient TSP samples were analyzed for 27 major, minor and trace elements. Particulate emissions were also collected from a variety of sources including fly ash, lignite dust, automobile traffic, domestic heating, and open-air burning of agricultural biomass and refuse, and analyzed for the same chemical components. Ambient and source chemical profiles were used for source identification and apportionment of TSP by employing a chemical mass balance (CMB) receptor model. Diesel burning in vehicular traffic and in the power plants for generator start up was found to be the major contributor to ambient TSP levels at all 10 sites. Other sources with significant contributions were domestic coal burning, vegetative burning (wood combustion and agricultural burns) and refuse open-air burning. Fly ash escaping the electrostatic precipitators of the power plants was a minor contributor to ambient TSP.

Findings obtained from the washing of black lignite from Teruel. Experiencias obtenidas en la depuracion mediante lavado de los lignitos negros de Teruel

Energy Technology Data Exchange (ETDEWEB)

Suarez Perez, A; Carbajo Josa, J I; Kindelan Alonso, J M; Fernandez Trabanco, J J [ENDESA, Madrid (Spain)

1989-10-01

The article summarises findings from ENDESA pilot plant in Andorra (Teruel) during cleaning of black lignite using different types of equipment and washing methods. The project received grants from the Directorate General of Mines, the Aragon Provincial Council, OCIDE and Ocicarbon. Research began in 1984 in the ENADIMSA pilot plant and laboratory and continued with the construction in Andorra of a 5 t/hour pilot plant to which other equipment was later added to give a capacity of 50 t/hour. Currently, the plant continues to treat and investigate various types of coal from the coalfield in order to define washability parameters and obtain data which, using mixtures of coal from various mines, make it possible to achieve optimum results in the 500 t/hour industrial plant which is being built by ENDESA. 1 fig., 4 tabs.

The effect of environmental pollution on the respiratory system of lignite miners: a diachronic study.

Science.gov (United States)

Sichletidis, L; Tsiotsios, I; Chloros, D; Daskalopoulou, E; Ziomas, I; Michailidis, K; Kottakis, I; Konstantinidis, T H; Palladas, P

2004-01-01

It is not known whether working in surface lignite mines can cause x-ray lesions or disorders of respiratory function. The aim of the study was to investigate the diachronic impact of environmental pollution on the respiratory system of lignite miners at mines in Eordea, Greece. Cases of 199 workers (Group A) residing permanently in the Eordea valley and 151 (Group B) living outside the Eordea valley were studied during Phase I and then re-examined after three years (Phase II). These cases were compared to those of 71 office workers living in Eordea valley (Group C) and to 96 living in Grevena, a region without pollution (Group D). The study included the completion of the MRC questionnaire for the detection of respiratory diseases, pulmonary function tests, measurement of diffusion capacity, otorhinolaryngologic examination, rhinomanonetry as well as chest and paranasal cavity X-rays. Chronic bronchitis was reported by 26.8%, 24.8%, 17.9% and 10.6% respectively of the subjects of groups A, B, C and D according to the answers of the questionnaire (pmines under conditions of excessive pollution by airborne contaminants have a high prevalence of atrophic rhinitis and, in addition to other standard examinations, should undergo rhinomanometry testing and X-ray imaging of the paranasal cavities.

Advanced power assessment for Czech lignite task 3.6. Topical report

Energy Technology Data Exchange (ETDEWEB)

Sondreal, E.A.; Mann, M.D.; Weber, G.W.; Young, B.C.

1995-12-01

Major reforms in the Czech energy sector have been initiated to reverse 40 years of central planning, subsidized energy pricing, unchecked pollution from coal-fired plants, concerns over nuclear safety and fuel cycle management, and dependence on the former U.S.S.R. for oil, gas, and nuclear fuel processing. Prices for electricity, heat, and natural gas paid by industry are close to western levels, but subsidized prices for households are as much as 40% lower and below economic cost. State control of major energy enterprises is being reduced by moving toward government-regulated, investor-owned companies to raise needed capital, but with a strategic stake retained by the state. Foreign firms will participate in privatization, but they are not expected to acquire a controlling interest in Czech energy companies. Economic conditions in the Czech Republic are now improving after the disruptions caused by restructuring since 1989 and separation of the former Czech and Slovak Federal Republics in January 1993. The downturn in the economy after 1989 was concentrated in energy-intensive heavy industry, and recovery is paced by consumer trade, services, light industry and construction. Energy use in relation to gross domestic product (GDP) has declined, but it is still significantly higher than in OECD (Organization for Economic Cooperation and Development) countries. The GDP increased by 2% in 1994 after dropping 22% between 1989 and 1993. A positive balance of payments has been achieved, with foreign investment offsetting a small trade deficit. The government`s external debt is only 4% of GDP. This report studies the application of lignite resources within the newly formulated energy policies of the republic, in light of a move toward privatization and stronger air pollution regulations. Lignite has represented the major energy source for the country.

Concentration of heavy metals and trace elements in soils, waters and vegetables and assessment of health risk in the vicinity of a lignite-fired power plant

Energy Technology Data Exchange (ETDEWEB)

Noli, Fotini, E-mail: noli@chem.auth.gr; Tsamos, Panagiotis, E-mail: pktsamos@chem.auth.gr

2016-09-01

The pollution of agricultural soils, waters and products in the regions of lignite mines and fired power plants is of great importance. The concentration of As, Βa, Co, Cr, Sr, Sc, Th, U, Zn in soils and waters in the vicinity of a lignite-fired power plant in Northern Greece was determined using Instrumental Neutron Activation Analysis. The determination frequency was every three months during a period of one year in order to evaluate the seasonal impact of the pollution to the environment. Measurements were performed in three locations around the lignite mine as well as in one reference location at a certain distance from the mine. The results, which exhibited a slight seasonal variation, were compared, where possible, with literature values from other countries. The obtained data in most of the cases did not exceed the normal levels and indicated that the investigated area was only slightly contaminated. The concentration of heavy and trace metals was also measured in three common garden crops (tomato, cucumber and parsley) grown in this area. The calculated transfer factors (TF) from soil to vegetables and health risk quotients (HQ) do not denote a health risk. - Highlights: • Seasonal variation of heavy metals concentrations in soils and waters in a lignite mining area. • The elevated concentrations detected by NAA indicating minor contamination of the studied area. • Determination of minor and trace elements in vegetables. • The transfer factors and health risk quotients indicating a possible slight contamination in the area.

Concentration of heavy metals and trace elements in soils, waters and vegetables and assessment of health risk in the vicinity of a lignite-fired power plant

International Nuclear Information System (INIS)

Noli, Fotini; Tsamos, Panagiotis

2016-01-01

The pollution of agricultural soils, waters and products in the regions of lignite mines and fired power plants is of great importance. The concentration of As, Βa, Co, Cr, Sr, Sc, Th, U, Zn in soils and waters in the vicinity of a lignite-fired power plant in Northern Greece was determined using Instrumental Neutron Activation Analysis. The determination frequency was every three months during a period of one year in order to evaluate the seasonal impact of the pollution to the environment. Measurements were performed in three locations around the lignite mine as well as in one reference location at a certain distance from the mine. The results, which exhibited a slight seasonal variation, were compared, where possible, with literature values from other countries. The obtained data in most of the cases did not exceed the normal levels and indicated that the investigated area was only slightly contaminated. The concentration of heavy and trace metals was also measured in three common garden crops (tomato, cucumber and parsley) grown in this area. The calculated transfer factors (TF) from soil to vegetables and health risk quotients (HQ) do not denote a health risk. - Highlights: • Seasonal variation of heavy metals concentrations in soils and waters in a lignite mining area. • The elevated concentrations detected by NAA indicating minor contamination of the studied area. • Determination of minor and trace elements in vegetables. • The transfer factors and health risk quotients indicating a possible slight contamination in the area.

Thermal properties of milk fat, xanthine oxidase, caseins and whey proteins in pulsed electric field-treated bovine whole milk.

Science.gov (United States)

Sharma, Pankaj; Oey, Indrawati; Everett, David W

2016-09-15

Thermodynamics of milk components (milk fat, xanthine oxidase, caseins and whey proteins) in pulsed electric field (PEF)-treated milk were compared with thermally treated milk (63 °C for 30 min and 73 °C for 15s). PEF treatments were applied at 20 or 26 kV cm(-1) for 34 μs with or without pre-heating of milk (55 °C for 24s), using bipolar square wave pulses in a continuous mode of operation. PEF treatments did not affect the final temperatures of fat melting (Tmelting) or xanthine oxidase denaturation (Tdenaturation), whereas thermal treatments increased both the Tmelting of milk fat and the Tdenaturation for xanthine oxidase by 2-3 °C. Xanthine oxidase denaturation was ∼13% less after PEF treatments compared with the thermal treatments. The enthalpy change (ΔH of denaturation) of whey proteins decreased in the treated-milk, and denaturation increased with the treatment intensity. New endothermic peaks in the calorimetric thermograms of treated milk revealed the formation of complexes due to interactions between MFGM (milk fat globule membrane) proteins and skim milk proteins. Evidence for the adsorption of complexes onto the MFGM surface was obtained from the increase in surface hydrophobicity of proteins, revealing the presence of unfolded hydrophobic regions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Optimization of a lignite-fired open pulverizing system boiler process based on variations in the drying agent composition

International Nuclear Information System (INIS)

Ma, Youfu; Zhang, Hua; Yuan, Yichao; Wang, Zhiyun

2015-01-01

This paper evaluates three lignite-fired OPSB (open pulverizing system boiler) processes, named OPSB-A, OPSB-B and OPSB-C, corresponding to three options of drying agents used for the pulverizing systems. OPSB-B is similar to our previous work [18] on drying agent composition. Performances of the three OPSBs were calculated and compared with a 600 MW lignite-fired boiler as the reference. The results showed that the coal savings of OPSB-A and OPSB-C were 5.41% and 4.06% in comparison with the reference boiler, whereas for OPSB-B, the savings was 2.57%. Accordingly, emissions of each OPSB could be reduced in proportion to the coal savings. Among the three OPSBs, OPSB-C showed the best performance of water recovery from mill-exhausts because it had the highest mill-exhaust water dew point of 73.2 °C, whereas the exhaust dew points of OPSB-A and OPSB-B were 63.9 °C and 70.9 °C, respectively. Both OPSB-C and OPSB-B are beneficial for achieving a high mill-exhaust humidity ratio, which facilitates water recovery from the mill-exhaust, and a low oxygen content in mill-exhaust, which improves the operating safety of the pulverizing systems, whereas OPSB-A is relatively inferior in these respects. The OPSB-C process is recommended for engineering applications because of its favorable overall performances. - Highlights: • Three lignite-fired OPSB processes are analyzed based on a conventional 600 MW boiler. • OPSB-A, OPSB-B and OPSB-C show coal savings of 5.41%, 2.57 and 4.06%, respectively. • All OPSBs have a great advantage of water recovery from the flue gas, especially OPSB-C. • OPSB-C process is recommended in view of its favorable overall performances

Analysis of the effects of biomass on the co-pyrolysis of coal using TGA method

International Nuclear Information System (INIS)

Yaman, S.; Haykiri-Acma, H.

2009-01-01

Turkey is a developing country with a population of 7.15 million and its economy is the 16th biggest in the world and 7th biggest in Europe (after Germany, United Kingdom, France, Italy, Spain, and Russia) with a Gross Domestic Product (GDP) of about 700 billion dollar. Low quality lignitic coals are the most significant primary energy resources of Turkey. Consequently, production of lignite in 2007 is 72 million tons, representing about 7.5% of lignite consumption of the world. However, undesirable characteristics of these lignites such as low calorific value, high ash, and high sulfur are some of serious drawbacks in the usage of them in conventional burning systems, regarding problematic deposit formations and polluting emissions. Therefore, alternative processes for these lignites such as pyrolysis and gasification to produce fuel gases and chemical are preferable. In this study, co-pyrolysis characteristics of Afsin-Elbistan lignite with biomass species such as hazelnut shells, sunflower seed shells, and hybrid poplar were investigated by Non-isothermal Thermogravimetry (TGA) technique. Structural differences in the physical and chemical properties of the samples were studied applying some methods such as X-Ray Diffractometry and Scanning Electron Microscopy. This study showed that addition of such biomass materials into lignite and then co-pyrolysis of these mixtures led to conversion levels that are seriously higher than the conversion level of the lignite alone under the same pyrolytic conditions. It is concluded that there are evident differences between the thermal reactivities of the lignite and the biomass materials, and the increase in the thermal reactivity when biomass was introduced may be explained by synergistic interactions between the constituents of lignite and biomass. (author)

Model Research of Gas Emissions From Lignite and Biomass Co-Combustion in a Large Scale CFB Boiler

Directory of Open Access Journals (Sweden)

Krzywański Jarosław

2014-06-01

Full Text Available The paper is focused on the idea of a combustion modelling of a large-scale circulating fluidised bed boiler (CFB during coal and biomass co-combustion. Numerical computation results for three solid biomass fuels co-combustion with lignite are presented in the paper. The results of the calculation showed that in previously established kinetics equations for coal combustion, some reactions had to be modified as the combustion conditions changed with the fuel blend composition. Obtained CO2, CO, SO2 and NOx emissions are located in borders of ± 20% in the relationship to the experimental data. Experimental data was obtained for forest biomass, sunflower husk, willow and lignite cocombustion tests carried out on the atmospheric 261 MWe COMPACT CFB boiler operated in PGE Turow Power Station in Poland. The energy fraction of biomass in fuel blend was: 7%wt, 10%wt and 15%wt. The measured emissions of CO, SO2 and NOx (i.e. NO + NO2 were also shown in the paper. For all types of biomass added to the fuel blends the emission of the gaseous pollutants was lower than that for coal combustion.

Removal of Cd (II from Aqueous Media by Adsorption onto Chemically and Thermally Treated Rice Husk

Directory of Open Access Journals (Sweden)

María Camila Hoyos-Sánchez

2017-01-01

Full Text Available Chemically and thermally treated rice husks were evaluated as a potential decontaminant of toxic Cd (II in aqueous media. Rice husk (RH, a by-product from rice milling, was chemically treated with HCl and NaOH. Then, thermal treatments to 300, 500, and 700°C were applied. The chemical composition and morphological characteristics of RH were evaluated by different techniques. The specific surface area analysis of RH samples by BET nitrogen adsorption method provided specific surface areas ranging from 6 to 14 m2/g. SEM, FTIR, and EDX analyses of RH were carried out to determine the surface morphology, functional groups involved in metal binding mechanism, and C/O and C/Si ratios, respectively. The maximum Cd (II adsorption capacity was 28.27 mg/g at an optimum pH, 6.0. The kinetic studies revealed that adsorption process followed the pseudo-second-order kinetic model.

Oxidative desulfurization of Cayirhan lignites by permanganate solution

Energy Technology Data Exchange (ETDEWEB)

Guru, M.; Tuzun, F.N.; Murathan, A.S.; Asan, A.; Kiyak, T. [Gazi University, Ankara (Turkey). Dept. for Chemical Engineering

2008-07-01

Unless important developments record new and renewable energy sources, the role of fossil fuels as an energy resource goes on. It is possible to detect sulfur, heavy metals, and tracer elements such as arsenic and selenium by decreasing calorific value of coals. Sulfur oxides, which are the main pollutants in atmosphere, are irritative to humans and plants, and erosion occurs on buildings. Although there are high lignite reservoirs, high sulfur content limits the efficient use of them. In this research, it is aimed to convert combustible sulfur in coal to non-combustible sulfur form in the ash by oxidizing it with permanganate solution. During this research, the effect of two different parameters of potassium permanganate concentration, processing time, and mean particle size were investigated at constant room temperature and shaking rate. The conversion of combustible sulfur to non-combustible sulfur form was achieved optimally with 0.14 M potassium permanganate solution, 0.1 mm mean particle size at 16 h of treatment time, and the combustible sulfur amount was decreased by 46.37% compared to undoped conditions.

Grass and forb species for revegetation of mixed soil-lignite overburden in East Central Texas

Energy Technology Data Exchange (ETDEWEB)

Skousen, J.G.; Call, C.A. (West Virginia University, Morgantown, WV (USA). Division of Plant and Soil Sciences)

Ten grasses and seven forbs were seeded into mixed soil-lignite overburden in the Post Oak Savannah region of Texas and monitored for establishment and growth over a 3-year period without fertilization. Buffelgrass (Cenchrus ciliaris), green sprangletop (Leptochloa dubia), switchgrass (Panicum virgatum), and kleingrass (P. coloratum) developed monotypic stands with sufficent density, aerial cover, and aboveground biomass to stabilize the mixed soil-lignite overburden surface by the end of the first growing season. Plant mortality eliminated buffelgrass and green sprangletop stands by the end of the third growing season. Indiangrass (Sorghastrum nutans) developed a satisfactory stand by the end of the third growing season, while Oldworld bluestem (Bothriochloa X Dicanthium), yellow bluestem (Bothriochloa ischaemum), and sideoats grama (Bouteloua curtipendula) established at a slower rate. Cover and biomass measurements from an adjacent, unfertilized stand of Coastal bermudagrass (Cynodon dactylon) were compared with those of seeded grasses throughout the study. Partidge pea (Cassia fasciculata) established rapidly and had the greatest cover and biomass of all seeded forbs by the end of the first growing season. Sericea lespedeza (Lespedeza cuneata), Illinois bundleflower (Desmanthus illinoensis), and western indigo (Indigofera miniata) developed adequate stands for surface stabilization by the end of the third growing season, while faseanil indigo (Indigofera suffruticosa), virgata lespedeza (Lespedeza virgata), and awnless bushsunflower (Simsia calva) showed slower establishment. 27 refs., 3 tabs.

Role of NSO compounds during primary cracking of a Type II kerogen and a Type III lignite

Science.gov (United States)

Behar, F.; Lorant, F.; Lewan, M.

2008-01-01

The aim of this work is to follow the generation of NSO compounds during the artificial maturation of an immature Type II kerogen and a Type III lignite in order to determine the different sources of the petroleum potential during primary cracking. Experiments were carried out in closed system pyrolysis in the temperature range from 225 to 350 ??C. Two types of NSOs were recovered: one is soluble in n-pentane and the second in dichloromethane. A kinetic scheme was optimised including both kerogen and NSO cracking. It was validated by complementary experiments carried out on isolated asphaltenes generated from the Type II kerogen and on the total n-pentane and DCM extracts generated from the Type III lignite. Results show that kerogen and lignite first decompose into DCM NSOs with minor generation of hydrocarbons. Then, the main source of petroleum potential originates from secondary cracking of both DCM and n-pentane NSOs through successive decomposition reactions. These results confirm the model proposed by Tissot [Tissot, B., 1969. Premie??res donne??es sur les me??canismes et la cine??tique de la formation du pe??trole dans les bassins se??dimentaires. Simulation d'un sche??ma re??actionnel sur ordinateur. Oil and Gas Science and Technology 24, 470-501] in which the main source of hydrocarbons is not the insoluble organic matter, but the NSO fraction. As secondary cracking of the NSOs largely overlaps that of the kerogen, it was demonstrated that bulk kinetics in open system is a result of both kerogen and NSO cracking. Thus, another kinetic scheme for primary cracking in open system was built as a combination of kerogen and NSO cracking. This new kinetic scheme accounts for both the rate and amounts of hydrocarbons generated in a closed pyrolysis system. Thus, the concept of successive steps for hydrocarbon generation is valid for the two types of pyrolysis system and, for the first time, a common kinetic scheme is available for extrapolating results to natural

Product analysis of catalytic multi-stage hydropyrolysis of lignite

Energy Technology Data Exchange (ETDEWEB)

Wen Li; Na Wang; Baoqing Li [Chinese Academy of Science, Taiyuan (China). State Key Lab of Coal Conversion, Institute of Coal Chemistry

2003-03-01

A lignite added with 0.2% MoS{sub 2} as catalyst was pyrolyzed under H{sub 2} using multi-stage heating method (MHyPy) which means holding a suitable time near the peak temperature. The product distribution and detailed analysis of products were performed. The results show that the tar yield increased to 63.9% during MHyPy compared with that of 51.8% in traditional hydropyrolysis (HyPy), while the gas yield decreased to a half. This suggests the effective utilization of hydrogen during MHyPy. The light aromatics in the tar from MHyPy increased remarkably 42, 37.8 and 115.4% for BTX, PCX and naphthalenes, respectively. Biphenyls were also observed in the tar from MHyPy, which indicated the effective hydrogenation occurs during catalytic MHyPy. The rich pore structure of the char from MHyPy hints its high reactivity in the subsequent conversion process such as gasification and combustion. 15 refs., 7 figs., 2 tabs.

Supercritical gas extracts from low-quality coals. On the search of new precursors for carbon materials

Energy Technology Data Exchange (ETDEWEB)

Garcia, Roberto; Arenillas, Ana; Rubiera, Fernando; Moinelo, Sabino R. [Instituto Nacional del Carbon INCAR, CSIC, Apartado 73, 33080, Oviedo (Spain)

2004-11-25

This paper studies the chemical composition of several supercritical gas (SCG) extracts and its influence on the thermal behaviour under carbonisation conditions. The extracts were obtained from a Spanish lignite (Mequinenza), a low-quality coal from the point of view of energy applications. The lignite was treated with toluene, ethanol (EtOH) and tetrahydrofuran (THF) as solvents under different supercritical temperature and pressure conditions. The extracts display high aliphatic nature and enhanced concentrations of oxygen functional groups, aided by the contribution of hydrogenation and oxygen incorporation reactions occurring in the SCG extraction with EtOH and THF. Thiophenic compounds are also present in great concentrations derived from the exceptionally high organic sulphur content of the parent coal. The carbonisation of the extracts renders anisotropic material with fine mosaic texture, as a consequence of the significant thermal reactivity inferred by the aliphatic and oxygenated groups. The size of the mosaic increases with the temperature of the SCG extraction and varies with the supercritical solvent in the order: toluene

Spatial and vertical distribution and risk assessment of natural radionuclides in soils surrounding the lignite-fired power plants in Megalopolis basin, Greece.

Science.gov (United States)

Papaefthymiou, H V; Manousakas, M; Fouskas, A; Siavalas, G

2013-01-01

Twenty soil profile samples and fourteen surface soil samples collected from the vicinity of the lignite-fired power plants in the Megalopolis basin (Greece) were analysed for their natural radionuclide concentration and (137)Cs, since fossil fuels are associated with naturally occurring radioactive materials and hence with radiological impact. No significant enhancement of surface soil radioactivity levels in the vicinity of lignite-fired plants was observed. A downcore decreasing trend of (137)Cs was observed in a number of cores reflecting its atmospheric origin, whereas the uniform distribution observed in a number of other cores gave information on the mechanical alteration of the soil. The average dose rate value was found to be 63 ± 22 nGy h(-1), while the annual average effective dose from the terrestrial gamma radiation was found to be 0.08 ± 0.03 mSv.

Over one thousand patients with early stage endometriosis treated with the Helica Thermal Coagulator (HELICA): safety aspects.

Science.gov (United States)

Hill, Nicholas; McQueen, John; Morey, Richard; Hanna, Leila; Chandakas, Stefanos; El-Toukhy, Tarek; Erian, John

2006-07-01

To assess the safety of the Helica Thermal Coagulator in the laparoscopic treatment of early stage endometriosis. Retrospective, observational. The Princess Royal University Hospital, The Sloane and Chelsfield Park Hospitals, Kent, UK. One thousand and sixty patients with early stage endometriosis. All patients were treated laparoscopically with the Helica Thermal Coagulator; a new laparoscopic device that combines electrical energy with helium for the treatment of endometriosis. No major bladder, ureteric or bowel injuries occurred. The only complication was a perforated vagina from the cutting probe during dissection of the cul-de-sac in a patient with a vaginal endometriotic nodule. The Helica Thermal Coagulator is a safe device for the laparoscopic treatment of endometriosis.

Degradation of Thermal Barrier Coatings from Deposits and Its Mitigation

Energy Technology Data Exchange (ETDEWEB)

Nitin Padture

2011-12-31

Ceramic thermal barrier coatings (TBCs) used in gas-turbine engines afford higher operating temperatures, resulting in enhanced efficiencies and performance. However, in the case of syngas-fired engines, fly ash particulate impurities that may be present in syngas can melt on the hotter TBC surfaces and form glassy deposits. These deposits can penetrate the TBCs leading to their failure. In experiments using lignite fly ash to simulate these conditions we show that conventional TBCs of composition 93wt% ZrO{sub 2} + 7wt% Y{sub 2}O{sub 3} (7YSZ) fabricated using the air plasma spray (APS) process are completely destroyed by the molten fly ash. The molten fly ash is found to penetrate the full thickness of the TBC. The mechanisms by which this occurs appear to be similar to those observed in degradation of 7YSZ TBCs by molten calcium-magnesium-aluminosilicate (CMAS) sand and by molten volcanic ash in aircraft engines. In contrast, APS TBCs of Gd{sub 2Zr{sub 2}O{sub 7} composition are highly resistant to attack by molten lignite fly ash under identical conditions, where the molten ash penetrates ~25% of TBC thickness. This damage mitigation appears to be due to the formation of an impervious, stable crystalline layer at the fly ash/Gd{sub 2}Zr{sub 2}O{sub 7} TBC interface arresting the penetrating moltenfly- ash front. Additionally, these TBCs were tested using a rig with thermal gradient and simultaneous accumulation of ash. Modeling using an established mechanics model has been performed to illustrate the modes of delamination, as well as further opportunities to optimize coating microstructure. Transfer of the technology was developed in this program to all interested parties.

Desulfurization reaction of high sulfur content flue gas treated by electron beam

International Nuclear Information System (INIS)

Hirosawa, Shojiro; Suzuki, Ryoji; Aoki, Shinji; Kojima, Takuji; Hashimoto, Shoji

2002-01-01

Experiments of flue gas treatment by electron beam were carried out, using simulated ligniteburning flue gas containing SO 2 (5500 ppm), NO (390 ppm) and H 2 O (22%). Removal efficiency of SO 2 was more than 90% at a dose of 1-2 kGy. It shows applicability of electron beam for treatment of lignite-burning flue gas. Another removal reaction besides the radiation-induced radical reaction and the thermal reaction occurring without irradiation was suggested by the facts that removal of SO 2 by the radical reaction is only a few hundreds of ppm and the removal amounts by thermal reaction under irradiation is lower than a half of total desulfurization. The mechanism similar to thermal reaction was proposed, assuming simultaneous uptake reaction of SO 2 and NH 3 on the surface of liquid aerosol. It was suggested that ammonium nitrate having deliquescence relative humidity (DRH) of 60% at 25 deg C plays an important role in producing liquid aerosols. Decrease of DRH of ammonium nitrate with elevating temperature and with formation of double salt of ammonium sulfate results in enhancement of formation of liquid aerosols. (author)

Solidification and Biotoxicity Assessment of Thermally Treated Municipal Solid Waste Incineration (MSWI) Fly Ash.

Science.gov (United States)

Gong, Bing; Deng, Yi; Yang, Yuanyi; Tan, Swee Ngin; Liu, Qianni; Yang, Weizhong

2017-06-10

In the present work, thermal treatment was used to stabilize municipal solid waste incineration (MSWI) fly ash, which was considered hazardous waste. Toxicity characteristic leaching procedure (TCLP) results indicated that, after the thermal process, the leaching concentrations of Pb, Cu, and Zn decreased from 8.08 to 0.16 mg/L, 0.12 to 0.017 mg/L and 0.39 to 0.1 mg/L, respectively, which well met the limits in GB5085.3-2007 and GB16689-2008. Thermal treatment showed a negative effect on the leachability of Cr with concentrations increasing from 0.1 to 1.28 mg/L; nevertheless, it was still under the limitations. XRD analysis suggested that, after thermal treatments, CaO was newly generated. CaO was a main contribution to higher Cr leaching concentrations owing to the formation of Cr (VI)-compounds such as CaCrO₄. SEM/EDS tests revealed that particle adhesion, agglomeration, and grain growth happened during the thermal process and thus diminished the leachability of Pb, Cu, and Zn, but these processes had no significant influence on the leaching of Cr. A microbial assay demonstrated that all thermally treated samples yet possessed strong bactericidal activity according to optical density (OD) test results. Among all samples, the OD value of raw fly ash (RFA) was lowest followed by FA700-10, FA900-10, and FA1100-10 in an increasing order, which indicated that the sequence of the biotoxicity for these samples was RFA > FA700-10 > FA900-10 > FA1100-10. This preliminary study indicated that, apart from TCLP criteria, the biotoxicity assessment was indispensable for evaluating the effect of thermal treatment for MSWI fly ash.

Investigations on high temperature coking of lignite with the help of radionuclide techniques

International Nuclear Information System (INIS)

Koennecke, H.G.; Luther, D.; Abendroth, H.C.

1986-01-01

The time characteristics and the varying flow characteristics of fine-grained briquettes during the high temperature coking of lignite according to Rammler and Bilkenroth were studied with the help of radionuclide technique. The process parameters (tsub(V), zsub(R), etc.) refer to the different zones of the coke furnace (bunker/dryer, coker/cooler). The different time charakteristics of the coke-grain fractions formed during the BHT-process enables a correlation of the retention time and the quality factors of the coke. The results obtained would enable a better operation of the individual furnaces in the plant and offer the basis for further process developments. (orig.) [de

Natural radioisotopes in lignite of the Ptolemais region (Greece) and in their ashes

International Nuclear Information System (INIS)

Simopoulos, S.E.; Angelopoulos, M.G.

1987-01-01

Samples of lignite, fly ash and bottom ash of a power plant, located in the Ptolemais region, were examined by gamma spectroscopy and their concentrations in Ra-226, Ra-228 and K-40 have been determined. These samples were prepared from samples taken daily for a period of one month. The brown coal samples are taken from the front of the brown coal field supplying one of the units. They show a flutuation of the concentrations of the same radionuclides in the brown coal seams and in the intermediate layers. Further samples taken from 3 small private mines of the Ptolemais region were also examined. (author)

Thermal and mechanical properties of NaOH treated hemp fabric and calcined nanoclay-reinforced cement nanocomposites

International Nuclear Information System (INIS)

Hakamy, A.; Shaikh, F.U.A.; Low, I.M.

2015-01-01

Highlights: • Fabrication of nanoclay and hemp fabric-reinforced cement composites. • The optimum nanoclay and hemp fabric content is 1.0 and 6.9 wt.% respectively. • Surface-treated hemp fabric-reinforced cement composites demonstrated better mechanical properties. • Surface modification of hemp fabric was effective in improving the hemp fabric-cement matrix adhesion. - Abstract: Cement nanocomposites reinforced with hemp fabrics and calcined nanoclay (CNC) have been fabricated and investigated. CNC is prepared by heating nanoclay (Cloisite 30B) at 900 °C for 2 h. The influences of CNC dispersion on the mechanical properties and thermal properties of these composites have been characterized in terms of porosity, density, water absorption, flexural strength, fracture toughness, impact strength and thermal stability. The microstructure is investigated using Quantitative X-ray Diffraction Analysis (QXDA) and High Resolution Transmission Electron Microscopy (HRTEM). The effects of alkali (NaOH) treatment of hemp fabric on the mechanical properties of hemp fabric-reinforced cement composites with different fabric contents of 4.5, 5.7, 6.9 and 8.1 wt% are also investigated. Results show that the optimum hemp fabric content is 6.9 wt% (i.e. 6 fabric layers). Results also indicated that physical, mechanical and thermal properties were enhanced due to the addition of CNC into the cement matrix and the optimum content of CNC was 1 wt%. The treated hemp fabric-reinforced nanocomposites containing 1 wt% CNC exhibited the highest flexural strength, fracture toughness, impact strength and thermal stability by virtue of good fibre–matrix interface. This environmentally friendly nanocomposite can be used for various construction applications such as ceilings and roofs

Development of a machine treating removed shells and others in thermal and nuclear power stations

International Nuclear Information System (INIS)

Daiho, Koichi; Iwao, Takenobu

1981-01-01

The living things removed form the cooling water systems in thermal and nuclear power stations, such as shells and jelly fish, have been disposed by burying in the premises, but it is the actual situation that the occurrence of bad smell and the securing of land for burying are the worries. Accordingly, a machine for deodorizing the removed living things was manufactured for trial, and the treatment experiment was carried out in Chita Power Station. This treating machine dries the removed living things around 200 deg C, and makes the deodorizing treatment. The treated products can be utilized effectively as fertilizer, and the prospect to put this machine in practical use as a waste treatment machine of resource re-utilization type was obtained. General Technical Research Institute, Chubu Electric Power Co., Inc., has developed a machine treating abandoned fish for making organic fertilizer, and its principle was applied to the development of this treating machine. The treating capacity of this machine is 1 t/day, and the power consumption is 9.3 kW. The waste oil from power stations of about 15 l/h is used as the fuel. A crusher, a constant feed screw conveyer and a rotary kiln for drying are used. In the treating experiment, about 30 t of shells and others were treated during 51 days. The results are reported. (Kako, I.)

Chemical characterization and receptor modeling of PM10 in the surroundings of the opencast lignite mines of Western Macedonia, Greece.

Science.gov (United States)

Samara, Constantini; Argyropoulos, George; Grigoratos, Theodoros; Kouras, Αthanasios; Manoli, Εvangelia; Andreadou, Symela; Pavloudakis, Fragkiskos; Sahanidis, Chariton

2018-05-01

The Western Macedonian Lignite Center (WMLC) in northwestern Greece is the major lignite center in the Balkans feeding four major power plants of total power exceeding 4 GW. Concentrations of PM 10 (i.e., particulate matters with diameters ≤10 μm) are the main concern in the region, and the high levels observed are often attributed to the activities related to power generation. In this study, the contribution of fugitive dust emissions from the opencast lignite mines to the ambient levels of PM 10 in the surroundings was estimated by performing chemical mass balance (CMB) receptor modeling. For this purpose, PM 10 samples were concurrently collected at four receptor sites located in the periphery of the mine area during the cold and the warm periods of the year (November-December 2011 and August-September 2012), and analyzed for a total of 26 macro- and trace elements and ionic species (sulfate, nitrate, chloride). The robotic chemical mass balance (RCMB) model was employed for source identification/apportionment of PM 10 at each receptor site using as inputs the ambient concentrations and the chemical profiles of various sources including the major mine operations, the fly ash escaping the electrostatic filters of the power plants, and other primary and secondary sources. Mean measured PM 10 concentrations at the different sites ranged from 38 to 72 μg m -3 . The estimated total contribution of mines ranged between 9 and 22% in the cold period increasing to 36-42% in the dry warm period. Other significant sources were vehicular traffic, biomass burning, and secondary sulfate and nitrate aerosol. These results imply that more efficient measures to prevent and suppress fugitive dust emissions from the mines are needed.

Treating Fibrous Insulation to Reduce Thermal Conductivity

Science.gov (United States)

Zinn, Alfred; Tarkanian, Ryan

2009-01-01

A chemical treatment reduces the convective and radiative contributions to the effective thermal conductivity of porous fibrous thermal-insulation tile. The net effect of the treatment is to coat the surfaces of fibers with a mixture of transition-metal oxides (TMOs) without filling the pores. The TMO coats reduce the cross-sectional areas available for convection while absorbing and scattering thermal radiation in the pores, thereby rendering the tile largely opaque to thermal radiation. The treatment involves a sol-gel process: A solution containing a mixture of transition-metal-oxide-precursor salts plus a gelling agent (e.g., tetraethylorthosilicate) is partially cured, then, before it visibly gels, is used to impregnate the tile. The solution in the tile is gelled, then dried, and then the tile is fired to convert the precursor salts to the desired mixed TMO phases. The amounts of the various TMOs ultimately incorporated into the tile can be tailored via the concentrations of salts in the solution, and the impregnation depth can be tailored via the viscosity of the solution and/or the volume of the solution relative to that of the tile. The amounts of the TMOs determine the absorption and scattering spectra.

Mineralogy and microstructure of sintered lignite coal fly ash

Energy Technology Data Exchange (ETDEWEB)

Marina Ilic; Christopher Cheeseman; Christopher Sollars; Jonathan Knight [Faculty of Technology and Metallurgy, Belgrade (Yugoslavia)

2003-02-01

Lignite coal fly ash from the 'Nikola Tesla' power plant in Yugoslavia has been characterised, milled, compacted and sintered to form monolithic ceramic materials. The effect of firing at temperatures between 1130 and 1190{sup o}C on the density, water accessible porosity, mineralogy and microstructure of sintered samples is reported. This class C fly ash has an initial average particle size of 82 {mu}m and contains siliceous glass together with the crystalline phases quartz, anorthite, gehlenite, hematite and mullite. Milling the ash to an average particle size of 5.6 m, compacting and firing at 1170{sup o}C for 1 h produces materials with densities similar to clay-based ceramics that exhibit low water absorption. Sintering reduces the amount of glass, quartz, gehlenite and anhydrite, but increases formation of anorthite, mullite, hematite and cristobalite. SEM confirms the formation of a dense ceramic at 1170{sup o}C and indicates that pyroplastic effects cause pore formation and bloating at 1190{sup o}C. 23 refs., 6 figs., 2 tabs.

The clean coal technologies for lignitic coal power generation in Pakistan

International Nuclear Information System (INIS)

Mir, S.; Raza, Z.; Aziz-ur-Rehman, A.

1995-01-01

Pakistan contains huge reserves of lignitic coals. These are high sulphur, high ash coals. In spite of this unfortunate situation, the heavy demand for energy production, requires the development utilization of these indigenous coal reserves to enhance energy production. The central of the environmental pollution caused by the combustion of these coals has been a major hindrance in their utilization. Recently a substantial reduction in coal combustion emissions have been achieved through the development of clean coal technologies. Pakistan through the transfer and adaptation of the advanced clean coal technologies can utilize incurring the high sulphur coals for energy production without incurring the environmental effects that the developed countries have experienced in the past. The author discusses the recently developed clean coal utilization technologies, their applications economies and feasibility of utilization with specific reference to Pakistan''s coal. (author)

Growth response of microorganisms to different molecular fractions of lignite

Energy Technology Data Exchange (ETDEWEB)

Polman, J.K.; Breckenridge, C.R.; Dugan, P.R.; Quigley, D.R.

1990-01-01

Our research is primarily concerned with isolating and characterizing microbes which are able to dissimilate coal and convert it to other useful chemicals. This quarter, general growth responses of microorganisms cultivated in the presence of different molecular weight fractions of lignite coal were examined. Aerobic and anaerobic environmental samples from a variety of ecological niches were used as inocula. Growth of the microorganisms in these samples on the following types of media was tested: COAL medium, containing alkali-solubilized whole coal; THFI medium, containing the alkali-solubilized, tetrahydrofuran-insoluble, macromolecular portion of whole coal; THFS medium, containing the THF-soluble, low molecular weight portion of whole coal; and CON medium, void of any coal constituent. Overall results indicated that the presence of the THF-soluble, low molecular weight coal fraction enhanced the growth yield and the variety of aerobic microorganisms compared to the other coal fractions or the control medium. Conversely, anaerobic microbes grew best on media which contained the macromolecular fraction. 12 refs., 5 tabs.

Thermal Diffusivity Measurements in Edible Oils using Transient Thermal Lens

Science.gov (United States)

Valdez, R. Carbajal.; Pérez, J. L. Jiménez.; Cruz-Orea, A.; Martín-Martínez, E. San.

2006-11-01

Time resolved thermal lens (TL) spectrometry is applied to the study of the thermal diffusivity of edible oils such as olive, and refined and thermally treated avocado oils. A two laser mismatched-mode experimental configuration was used, with a He Ne laser as a probe beam and an Ar+ laser as the excitation one. The characteristic time constant of the transient thermal lens was obtained by fitting the experimental data to the theoretical expression for a transient thermal lens. The results showed that virgin olive oil has a higher thermal diffusivity than for refined and thermally treated avocado oils. This measured thermal property may contribute to a better understanding of the quality of edible oils, which is very important in the food industry. The thermal diffusivity results for virgin olive oil, obtained from this technique, agree with those reported in the literature.

Thermal and infrared-diode laser effects on indocyanine-green-treated corneal collagen

Science.gov (United States)

Timberlake, George T.; Patmore, Ann; Shallal, Assaad; McHugh, Dominic; Marshall, John

1993-07-01

It has been suggested that laser welds of collagenous tissues form by interdigitation and chemical bonding of thermally 'unraveled' collagen fibrils. We investigated this proposal by attempting to weld highly collagenous, avascular corneal tissue with an infrared (IR) diode laser as follows. First, the temperature at which corneal collagen shrinks and collagen fibrils 'split' into subfibrillary components was determined. Second, since use of a near-IR laser wavelength necessitated addition of an absorbing dye (indocyanine green (ICG) to the cornea, we measured absorption spectra of ICG-treated tissue to ensure that peak ICG absorbance did not change markedly when ICG was present in the cornea. Third, using gel electrophoresis of thermally altered corneal collagen, we searched for covalently crosslinked compounds predicted by the proposed welding mechanism. Finally, we attempted to weld partial thickness corneal incisions infused with ICG. Principal experimental findings were as follows: (1) Human corneal (type I) collagen splits into subfibrillary components at approximately 63 degree(s)C, the same temperature that produces collagen shrinkage. (2) Peak ICG absorption does not change significantly in corneal stroma or with laser heating. (3) No evidence was found for the formation of novel compounds or the loss of proteins as a result of tissue heating. All tissue treated with ICG, however, exhibited a novel 244 kD protein band indicating chemical activity between collagen and corneal stromal components. (4) Laser welding corneal incisions was unsuccessful possibly due to shrinkage of the sides of the incision, lack of incision compression during heating, or a less than optimal combination of ICG concentration and radiant exposure. In summary, these experiments demonstrate the biochemical and morphological complexity of ICG-enhanced IR laser-tissue welding and the need for further investigation of laser welding mechanisms.

Thermal Integration of CO{sub 2} Compression Processes with Coal-Fired Power Plants Equipped with Carbon Capture

Energy Technology Data Exchange (ETDEWEB)

Edward Levy

2012-06-29

Coal-fired power plants, equipped either with oxycombustion or post-combustion CO{sub 2} capture, will require a CO{sub 2} compression system to increase the pressure of the CO{sub 2} to the level needed for sequestration. Most analyses show that CO{sub 2} compression will have a significant effect on parasitic load, will be a major capital cost, and will contribute significantly to reduced unit efficiency. This project used first principle engineering analyses and computer simulations to determine the effects of utilizing compressor waste heat to improve power plant efficiency and increase net power output of coal-fired power plants with carbon capture. This was done for units with post combustion solvent-based CO{sub 2} capture systems and for oxyfired power plants, firing bituminous, PRB and lignite coals. The thermal integration opportunities analyzed for oxycombustion capture are use of compressor waste heat to reheat recirculated flue gas, preheat boiler feedwater and predry high-moisture coals prior to pulverizing the coal. Among the thermal integration opportunities analyzed for post combustion capture systems are use of compressor waste heat and heat recovered from the stripper condenser to regenerate post-combustion CO{sub 2} capture solvent, preheat boiler feedwater and predry high-moisture coals. The overall conclusion from the oxyfuel simulations is that thermal integration of compressor heat has the potential to improve net unit heat rate by up to 8.4 percent, but the actual magnitude of the improvement will depend on the type of heat sink used and to a lesser extent, compressor design and coal rank. The simulations of a unit with a MEA post combustion capture system showed that thermal integration of either compressor heat or stripper condenser heat to preheat boiler feedwater would result in heat rate improvements from 1.20 percent to 4.19 percent. The MEA capture simulations further showed that partial drying of low rank coals, done in combination

Baseline risk assessment of ground water contamination at the inactive uraniferous lignite ashing site near Bowman, North Dakota

Energy Technology Data Exchange (ETDEWEB)

1994-11-01

This baseline risk assessment of ground water contamination at the inactive uraniferous lignite ashing site near Bowman, North Dakota, evaluates the potential impacts to public health or the environment from contaminated ground water at this site. This contamination is a result of the uraniferous lignite ashing process, when coal containing uranium was burned to produce uranium. Potential risk is quantified only for constituents introduced by the processing activities and not for the constituents naturally occurring in background ground water in the site vicinity. Background ground water, separate from any site-related contamination, imposes a percentage of the overall risk from ground water ingestion in the Bowman site vicinity. The US Department of Energy (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project is developing plans to address soil and ground water contamination at the site. The UMTRA Surface Project involves the determination of the extent of soil contamination and design of an engineered disposal cell for long-term storage of contaminated materials. The UMTRA Ground Water Project evaluates ground water contamination. Based on results from future site monitoring activities as defined in the site observational work plan and results from this risk assessment, the DOE will propose an approach for managing contaminated ground water at the Bowman site.

Baseline risk assessment of ground water contamination at the inactive uraniferous lignite ashing site near Bowman, North Dakota

International Nuclear Information System (INIS)

1994-11-01

This baseline risk assessment of ground water contamination at the inactive uraniferous lignite ashing site near Bowman, North Dakota, evaluates the potential impacts to public health or the environment from contaminated ground water at this site. This contamination is a result of the uraniferous lignite ashing process, when coal containing uranium was burned to produce uranium. Potential risk is quantified only for constituents introduced by the processing activities and not for the constituents naturally occurring in background ground water in the site vicinity. Background ground water, separate from any site-related contamination, imposes a percentage of the overall risk from ground water ingestion in the Bowman site vicinity. The US Department of Energy (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project is developing plans to address soil and ground water contamination at the site. The UMTRA Surface Project involves the determination of the extent of soil contamination and design of an engineered disposal cell for long-term storage of contaminated materials. The UMTRA Ground Water Project evaluates ground water contamination. Based on results from future site monitoring activities as defined in the site observational work plan and results from this risk assessment, the DOE will propose an approach for managing contaminated ground water at the Bowman site

Depositional environment of the San Miguel lignite deposit in Atascosa and McMullen Counties, Texas

Energy Technology Data Exchange (ETDEWEB)

Gowan, S.W.

1985-01-01

An analysis of the environment of deposition of the San Miguel lignite deposit was carried out in order to understand newly discovered characteristics of the deposit. The environment of deposition of the overburden and underburden was evaluated through an interpretation of three continuous cores. Four coal cores and a highwall section were carefully described to determine the depositional environmental of the coal seams and partings. These studies were supplemented by the construction of seam and parting isopachs, and the analysis of the distribution of sulfur isotopes, sulfur, forms, and total sulfur within the coal. The sedimentary package is composed of a basal prograding barrier that beach, dune, and back-barrier sands. This unit correlates with a downdip sand that was also interpreted as a prograding barrier by other authors. The barrier is overlain by a series of slit and clay deposits of lagoonal, tidal flat, and tidal channel origin. These deposits are capped by restricted lagoon sediments composed of green, calcareous clays that occasionally contain shell layers. The restricted lagoon deposits formed when the barrier closed the lagoon off from the sea. Peat forming freshwater swamps eventually became established behind the barrier and on top of the restricted lagoon sediments. The parting isopachs reveal a reticulate morphology similar to the mangrove swamps located lateral to the modern Niger River Delta. The partings represent vegetated tidal flat deposits that formed during periodic invasions by the sea that killed the swamp and inundated the peat with sulfate rich water. The lignite interval is capped by open lagoon and tidal flat sediments.

The effects of leaching and floatation on the ash fusion temperatures of three selected lignites

Energy Technology Data Exchange (ETDEWEB)

Feng-hai Li; Jie-jie Huang; Yi-tian Fang; Yang Wang [Chinese Academy of Sciences, Taiyuan (China). Institute of Coal Chemistry

2011-07-15

Experiments have been conducted with Huolinhe (HLH), Xiaolongtan (XLT), and Ethiopian (ET) lignites to investigate the effects of washing with water, acid-leaching, and floatation on their ash fusion temperatures (AFTs). The results show that the AFTs of XLT and ET are elevated by washing with water and floatation, but the AFT of HLH is decreased. The AFTs of all three lignites are increased markedly by acid leaching. A decrease in the total basic composition in ash increases its AFT, and vice versa. Changes in the mineral contents of the coals after treatment contribute to the variations in their AFTs. After washing with water, the lower AFT of HLH is brought about by the increases in the amounts of cordierite and anhydrite, whereas the higher AFT of XLT is caused by the decreases in the amounts of anhydrite and calcite. For the floatation treatment, the decrease of AFT for HLH is due to the reduction in the amount of kaolinite, but the elevation of AFT for XLT or ET is caused by the decrease in the amount of pyrite and the reductions in the amounts of gypsum and xanthoxenite, respectively. For the acid-leaching treatment, a decrease in the amount of pyrite and an increase in the amount of kaolinite result in increases in AFTs for HLH and XLT. Increases in the amounts of kaolinite and cristobalite in FET (ET after floatation), WET (ET after washing with water), and AET (ET after acid-leaching) lead to corresponding increases in the AFTs. 27 refs., 10 figs., 3 tabs.

On the consideration of geological uncertainties in the evaluation of lignite deposits; Zur Beruecksichtigung geologischer Ungewissheit in der Bewertung von Braunkohlevorkommen

Energy Technology Data Exchange (ETDEWEB)

Benndorf, Joerg [Technische Univ. Delft (Netherlands). Dept. of Geosciences and Engineering; Naworyta, Wojciech [AGH Univ. of Science and Technology, Cracow (Poland). Dept. of Open Pit Mining

2012-12-15

All phases of planning as well as the operational open-cast mining require a sufficient knowledge on the spatial distribution of the properties of deposits with respect to quality and geometrical structure. This knowledge is a requisition to a sustainable and optimal utilization of lignite as a raw material under security-related and economic aspects. The spatial distribution of the deposit based on exploration data utilizing different methods of interpolation is recognized as a planning framework and also illustrated in a three-dimensional model. The geo-statistics offers different approaches of modelling whereby at each time the specific tasks and aims specify the selection of the specific methodology. Under this aspect, the authors of the contribution under consideration compare different approaches of methodology with actual analyses using a deposit in Central Europe as a case study. These approaches of methodology are evaluated under the criteria of the prediction accuracy as well as their derivability from exceeding probabilities and lower deviation probabilities of threshold values. The results of this investigation give information about the profitability of certain concepts in the lignite mining.

Microtexture of the thermally grown alumina in commercial thermal barrier coatings

Energy Technology Data Exchange (ETDEWEB)

Karadge, M. [School of Materials, University of Manchester, Grosvenor St., Manchester M1 7HS (United Kingdom); Zhao, X. [School of Materials, University of Manchester, Grosvenor St., Manchester M1 7HS (United Kingdom); Preuss, M. [School of Materials, University of Manchester, Grosvenor St., Manchester M1 7HS (United Kingdom); Xiao, P. [School of Materials, University of Manchester, Grosvenor St., Manchester M1 7HS (United Kingdom)]. E-mail: Ping.Xiao@manchester.ac.uk

2006-02-15

otextures of the thermally grown {alpha}-alumina (TGO) in isothermally treated and thermal cycled electron beam physical vapor deposited thermal barrier coatings (EB-PVD-TBC) and isothermally treated air plasma sprayed (APS-TBC) specimens were studied by high resolution electron back-scattered diffraction. The TGO in EB-PVD specimens exhibited a basal microtexture. The TGO in APS specimens, however, did not show any significant microtexture development.

Co-liquefaction of Elbistan Lignite with Manure Biomass; Part 2 - Effect of Biomass Type, Waste to Lignite Ratio and Solid to Liquid Ratio

Science.gov (United States)

Karaca, Hüseyin; Koyunoglu, Cemil

2017-12-01

Most coal hydrogenation processes require a large quantity of hydrogen. In general, a coal derived liquid such as anthracene oil was used as a hydrogen donor solvent. Tetralin, partially hydrogenated pyrene, phenantrene and coal-derived solvents, which contain hydroaromatic compounds, are efficient solvents to donate hydrogen. In an attempt to reduce the high cost of hydrogen, part of the hydrogen was replaced by a low cost hydrogen donor solvent. This must be hydrogenated during or before the process and recycled. To reduce the cost of hydrogen donor vehicles instead of liquids recycled from the liquefaction process or several biomass types, industrial by products, liquid fractions derived from oil sands bitumen were successfully used to solubilize a coal from the past. In an attempt to reduce the high cost of hydrogen, part of the hydrogen was replaced by a low cost hydrogen donor solvent. However, when hydrogen is supplied from the hydroaromatic structures present in the solvent, the activity of coal minerals is too low to rehydrogenate the solvent in-situ. Nevertheless, a decrease of using oxygen, in addition to enhanced usage of the hydrogen supply by using various waste materials might lead to a decrease of the cost of the liquefaction procedure. So instead of using tetralin another feeding material such as biomass is becoming another solution improving hydrogen donor substances. Most of the liquefaction process were carried out in a batch reactor, in which the residence time of the liquefaction products is long enough to favour the retrogressive reactions, early studies which are related to liquefaction of coal with biomass generally focus on the synergetic effects of coal while biomass added. Early studies which are related to liquefaction of coal with biomass generally focus on the synergetic effects of coal while biomass added. Alternatively, to understand the hydrogen transfer from biomass to coal, in this study, Elbistan Lignite (EL) with manure, tea

Sulfurisation of lipids in a marine-influenced lignite

Energy Technology Data Exchange (ETDEWEB)

Sandison, C.M.; Alexander, R.; Kagi, R.I.; Boreham, C.J. [Curtin University of Technology, Perth, WA (Australia)

2002-07-01

Compelling evidence is presented for the process of lipid sulfurisation in humic coal-forming environments. The production of reduced inorganic sulfides by sulfate-reducing bacteria during a marine transgression, which occurred during early diagenesis, enabled the selective sequestration of functionalised lipids in the polar and asphaltene fractions from the Eocene, marine-influenced Heartbreak Ridge lignite deposit in southeast Western Australia. Nickel boride desulfurisation experiments conducted on these fractions released small but significant quantities of sulfur-bound hydrocarbons. These comprised mostly higher plant triterpanes, C-29 steranes and extended 17beta(H),21beta(H)-hopanes, linked by one sulfur atom at, or close to, functionalised sites in the original natural product precursors. These sulfurised lipids come from the same carbon sources as the free hydrocarbon lipids, except for the sulfurised extended hopanoids, which may be partially derived from a different bacterial source. These results indicate that the selectivity and nature of steroid and hopanoid vulcanisation in coal-forming mires is similar to that observed in other sedimentary environments. However, the diversity of higher plant triterpanes that can be sulfurised in marine transgressed coals is greater than that reported in immature terrestrial coals. This preservation mechanism explains the formation of the structurally related biomarkers in more mature sulfur-rich humic coals.

Cleaning of flue gases from lignite-fired power plants by electron beam technology

International Nuclear Information System (INIS)

Ruskov, T.

1998-01-01

An essential part of the electricity production in Bulgaria depends on the combustion of lignite with high humidity and high sulphur content. As a result of burning, toxic gases as sulphur dioxide (SO 2 ) and nitrous oxides (NO x ) are emitted in the atmosphere. Both S0 2 and NO x in flue gases could be removed simultaneously by the Electron Beam (EB) process. Beforehand cleaned from fly ash, the flue gas is cooled by injection of water and ammonia is added. By irradiation with high energy electrons, S0 2 and NO x are converted into aerosols of ammonium sulphate and ammonium nitrate. The byproduct is collected by an electrostatic precipitator and is used for the production of fertilisers

Isolation and identification of a Candida digboiensis strain from an extreme acid mine drainage of the Lignite Mine, Gujarat.

Science.gov (United States)

Patel, Mitesh J; Tipre, Devayani R; Dave, Shailesh R

2009-12-01

An extremely acidic mine drainage (AMD) water sample was collected in 1998 and 2008 from Panandhro lignite mine, Gujarat, India. The yeast isolated from this sample was identified using mini API identification system, as a member of genus Candida. The major cellular fatty acids detected by FAME from the isolate are C(16:0) and C(18:2) (cis 9,12)/C(18:0alpha) as 25.23 and 19.5%, respectively. The isolate was identified as Candida digboiensis by 18S rRNA gene sequence analysis and designated as Candida digboiensis SRDyeast1. Phylogenetic analysis using D1/D2 variable domains showed that the closest relative of this strain is Candida blankii with 3% divergence. This organism has been reported for the first time from the lignite mine AMD sample, and for cellular fatty acid analysis. This yeast is able to survive in the AMD sample preserved at 10-42 degrees C temperature since last 10 years along with iron oxidizing microorganisms. It can grow in the presence of 40% glucose, 10% NaCl and in the pH range of 1 to 10. The isolate is capable of producing enzymes like protease and lipase. This isolate differs from the type strain Candida digboiensis in as many as six physiological and metabolic characteristics.

Process of transforming into light oils heavy oils from carbonization of lignites, coals, etc

Energy Technology Data Exchange (ETDEWEB)

Mony, H

1926-12-20

A process is described for transforming into light oils the heavy oils coming from the carbonization of lignites, peats, coals, and shales, and heavy oils from original minerals and vegetables, consisting of heating the heavy oils or tars in the presence of one or more solid or liquid substances conveniently chosen, with a veiw to effect distillation of the oils under atmospheric pressure at an appropriate temperature, the solids or liquid substances favoring the formation of light products under the influence of heat, being preferably added to the oil before admitting it to the retort and heating, so that the light oils are obtained from the heavy oils in a single operation.

A comparison of improved power plant technologies on lignite with (PFBC) and (IGCC) cycles

International Nuclear Information System (INIS)

Cherepnalkovski, Ilija

1997-01-01

Technologies and process diagrams descriptions for PFBC (Pressurised Fluidized Bed Combustion) and IGCC (Integrated Gasification Combined Cycle) are presented as for improved cycles with modern clean coal technologies, the most popular currently. A special attention is paid to the possibilities for Macedonian lignites use on the power plants with PFBC and IGCC cycles. The comparison of the above mention technologies has been done particularly on the desulfurization, NO x reduction, ash elimination and its use in the building and construction industries. A comparison between the power plants with PFBC and IGCC cycles is made by the following criteria: cycle efficiency, desulfurization and nitrogen oxides reduction, power plant complexity and their cost, as well as plant reliability. (Author)

Controlling the excess heat from oxy-combustion of coal by blending with biomass

Energy Technology Data Exchange (ETDEWEB)

Haykiri-Acma, H.; Turan, A.Z.; Yaman, S.; Kucukbayrak, S. [Istanbul Technical University, Chemical and Metallurgical Engineering Faculty, Chemical Engineering Department, 34469, Maslak, Istanbul (Turkey)

2010-11-15

Two different biomass species such as sunflower seed shell and hazelnut shell were blended with Soma-Denis lignite to determine the effects of co-combustion on the thermal reactivity and the burnout of the lignite sample. For this purpose, Thermogravimetric Analysis and Differential Scanning Calorimetry techniques were applied from ambient to 900 C with a heating rate of 40 C/min under dry air and pure oxygen conditions. It was found that the thermal reactivities of the biomass materials and the lignite are highly different from each other under each oxidizing medium. On the other hand, the presence of biomass in the burning medium led to important influences not only on the burnout levels but also on the heat flows. The heat flow from the burning of lignite increased fivefold when the oxidizing medium was altered from dry air to pure oxygen. But, in case of co-combustion under oxygen, the excess heat arising from combustion of lignite could be reduced and this may be helpful to control the temperature of the combustion chamber. Based on this, co-combustion of coal/biomass blends under oxygen may be suggested as an alternative method to the ''Carbon Dioxide Recycle Method'' encountered in the oxyfuel combustion systems. (author)

Fluidized bed combustion with the use of Greek solid fuels

Directory of Open Access Journals (Sweden)

Kakaras Emmanuel

2003-01-01

Full Text Available The paper is an overview of the results obtained up to date from the combustion and co-combustion activities with Greek brown coal in different installations, both in semi-industrial and laboratory scale. Combustion tests with Greek lignite were realized in three different Circulating Fluidized Bed Combustion (CFBC facilities. Low rank lignite was burned in a pilot scale facility of approx. 100kW thermal capacity, located in Athens (NTUA and a semi-industrial scale of 1.2 MW thermal capacity, located at RWE's power station Niederaussem in Germany. Co-combustion tests with Greek xylitic lignite and waste wood were carried out in the 1 MWth CFBC installation of AE&E, in Austria. Lab-scale co-combustion tests of Greek pre-dried lignite with biomass were accomplished in a bubbling fluidized bed in order to investigate ash melting problems. The obtained results of all aforementioned activities showed that fluidized bed is the appropriate combustion technology to efficiently exploit the low quality Greek brown coal either alone or in conjunction with biomass species.

Effect of CaCO_3 addition on ash sintering behaviour during K_2CO_3 catalysed steam gasification of a Chinese lignite

International Nuclear Information System (INIS)

Zhang, Jiguang; Li, Jianbo; Mao, Yandong; Bi, Jicheng; Zhu, Mingming; Zhang, Zhezi; Zhang, Li; Zhang, Dongke

2017-01-01

Highlights: • K_2CO_3 decreased ash sintering temperature and enhanced ash melting in gasification. • CaCO_3 addition enhanced ash melting and lowered ash sintering temperatures. • CaCO_3 reacted with SiO_2 to form fluxing phases and amorphous materials. • CaCO_3 addition inhibited the potassium aluminium silicate formation. • CaCO_3 addition preserved the catalytic activity of potassium. - Abstract: The ash sintering behaviour of a Chinese lignite (LLI) with different amounts of CaCO_3 addition during K_2CO_3-catalysed gasification was investigated. 0–10 wt% K_2CO_3 was doped into the lignite for catalytic gasification, and CaCO_3 was added into the K_2CO_3-doped samples, varying in the range of 0–20 wt% relative to the lignite, for understanding its impact on ash sintering and catalytic gasification activity. Ash samples were prepared by completely gasifying the lignite samples with steam in a fixed-bed catalytic gasification system operating at 1073 K and atmospheric pressure. Sintering temperature, mineralogy and morphology of the ash samples thus obtained were determined using a pressure-drop sintering device, XRD and SEM-EDS, respectively. The results showed that the ash sintering temperature decreased as the K_2CO_3 addition increased, indicating that K_2CO_3 as the catalyst for gasification would promote ash sintering. SEM imaging analysis showed that all the ash samples from LLI with K_2CO_3 addition were composed of agglomerated particles with smooth surfaces, indicating the ashes had incurred partial melting. The degree of melting became more apparent as the K_2CO_3 addition ratio increased. These molten phases were identified as K-bearing arcanite and kaliophilite, which contributed to the formation of liquid phases at lower temperatures, resulting in lowered ash sintering temperatures. It was also revealed that the addition of CaCO_3 decreased the sintering temperatures of ash samples, indicating that the ash sintering was further

Biological functioning of PAH-polluted and thermal desorption-treated soils assessed by fauna and microbial bioindicators.

Science.gov (United States)

Cébron, Aurélie; Cortet, Jérôme; Criquet, Stéven; Biaz, Asmaa; Calvert, Virgile; Caupert, Cécile; Pernin, Céline; Leyval, Corinne

2011-11-01

A large number of soil bioindicators were used to assess biological diversity and activity in soil polluted with polycyclic aromatic hydrocarbons (PAHs) and the same soil after thermal desorption (TD) treatment. Abundance and biodiversity of bacteria, fungi, protozoa, nematodes and microarthropods, as well as functional parameters such as enzymatic activities and soil respiration, were assessed during a two year period of in situ monitoring. We investigated the influence of vegetation (spontaneous vegetation and Medicago sativa) and TD treatment on biological functioning. Multivariate analysis was performed to analyze the whole data set. A principal response curve (PRC) technique was used to evaluate the different treatments (various vegetation and contaminated vs. TD soil) contrasted with control (bare) soil over time. Our results indicated the value of using a number of complementary bioindicators, describing both diversity and functions, to assess the influence of vegetation on soil and discriminate polluted from thermal desorption (TD)-treated soil. Plants had an influence on the abundance and activity of all organisms examined in our study, favoring the whole trophic chain development. However, although TD-treated soil had a high abundance and diversity of microorganisms and fauna, enzymatic activities were weak because of the strong physical and chemical modifications of this soil. Copyright © 2011 Institut Pasteur. Published by Elsevier Masson SAS. All rights reserved.

Use of abandoned coal/lignite open pits for waste disposal in selected European countries

International Nuclear Information System (INIS)

Libicki, J.S.

1989-01-01

The use of abandoned coal/lignite pits as disposal sites for solid waste appears to be a reasonable approach to a difficult problem, especially if they are located close to the waste source. However, a potential for groundwater and soil pollution exists. This issue was discussed by a Group of Experts on Opencast Mining of the UN Economic Commission for Europe because most of the sites are operated by mining companies. This paper contains the major topics of discussion including the significance of the problem, legal aspects, characteristics of the open pits, waste intended for disposal, investigations required to obtain a disposal permit, disposal techniques, protection measures, monitoring environmental impacts, and research trends. A few countries are used as examples

Co-Liquefaction of Elbistan Lignite with Manure Biomass; Part 3 - Effect of Reaction Time and Temperature

Science.gov (United States)

Koyunoglu, Cemil; Karaca, Hüseyin

2017-12-01

Most of the liquefaction process were carried out in a batch reactor, in which the residence time of the liquefaction products is long enough to favour the retrogressive reactions. To minimize retrogressive reactions, the liquefaction of coal was carried out in a flowing solvent reactor in which a fixed bed of coal is continuously permeated by hot solvent. Solvent flowing through the coal bed carries the liquefaction products out of the reactor. Unlike experiments carried out under similar conditions in a batch reactor no increase in solid residue is observed during long time high temperature runs in the flowing solvent reactor. There is a greater appreciation of the importance of retrograde, or polymerization, reactions. If the free radicals formed when coal breaks down are not quickly capped with hydrogen, they react with each other to form large molecules that are much harder to break down than the original coal. Reaction time impacts both the co-liquefaction cost and the product yield. So as to study this idea, the experiments of Elbistan Lignite (EL) with manure co-liquefaction carried out by changing the reaction time from 30 to 120 minutes. As a result, the greatest oil products yields obtained at 60 minutes. Therefore, by thinking about the oil products yield values acquired, the optimal reaction time was obtained to be 60 minutes for Elbistan lignite (EL) with manure liquefied with the temperature of 350°C and 400°C. Above 425°C did not examine because solvent (tetraline) loses its function after 425 °C. The obtained optimum temperature found 400°C due to higher total conversion of liquefaction products and also oil+gas yields.

The Research on Thermal Properties and Hydrophobility of the Native Starch/hydrolysis Starch Blends with Treated CaCO3 Powder

Science.gov (United States)

Liu, Chia-I.; Huang, Chi-Yuan

2008-08-01

In this research, hydrolysis starch was added into the starch blends to study the thermal properties. The enthalpy of blends had a significant decrease to 109J/g as content of treated CaCO3 increased to 5wt%. The modified starch was degraded slightly to produce glucose in the hydrolysis treatment. The amount of glucose in native starch and hydrolysis starch was 0.09 μmol and 0.14 μmol by the DNS measurement. Moreover, CaCO3 treated with titanium coupling agent was also added to improve miscibility and hydrophobility in the starch blends. The contact angle of the blends increased from 60° to 95° when 15wt% treated CaCO3 was added. Treated CaCO3 was confirmed to improve the hydrophobility of starch blends effectively.

THE RESEARCH ON THERMAL PROPERTIES AND HYDROPHOBILITY OF THE NATIVE STARCH/HYDROLYSIS STARCH BLENDS WITH TREATED CaCO3 POWDER

International Nuclear Information System (INIS)

Liu, C.-I; Huang, C.-Y.

2008-01-01

In this research, hydrolysis starch was added into the starch blends to study the thermal properties. The enthalpy of blends had a significant decrease to 109J/g as content of treated CaCO 3 increased to 5wt%. The modified starch was degraded slightly to produce glucose in the hydrolysis treatment. The amount of glucose in native starch and hydrolysis starch was 0.09 μmol and 0.14 μmol by the DNS measurement. Moreover, CaCO 3 treated with titanium coupling agent was also added to improve miscibility and hydrophobility in the starch blends. The contact angle of the blends increased from 60 deg. to 95 deg. when 15wt% treated CaCO 3 was added. Treated CaCO 3 was confirmed to improve the hydrophobility of starch blends effectively

Advanced control - technologies for suppressing harmful emission in lignitic coal-fired power generation

International Nuclear Information System (INIS)

Mir, S.; Hai, S.M.A.

2000-01-01

The production of sufficient amount of indigenous energy is a prerequisite for the prosperity of a nation. Pakistan's energy demand far exceeds its indigenous supplies. A cursory look at the energy situation in Pakistan reveals that there is an urgent need for the development of its energy resources. In this regard, coal can play a key role if its problems of high-sulfur and high ash can be rectified through the adoption adaptation of advanced technologies, like (I) clean coal technologies, and (II) control technologies. A review on clean coal technologies for utilization of lignitic coals has already been published and the present article describes the effect of harmful emissions from the combustion of high sulfur coals, like the ones found in Pakistan and their control through advanced control technologies, to make a significant contribution in the total energy economics of Pakistan. (author)

The effect of the depth and groundwater on the formation of sinkholes or ground subsidence associated with abandoned room and pillar lignite mines under static and dynamic conditions

Directory of Open Access Journals (Sweden)

Ö. Aydan

2015-11-01

Full Text Available It is well known that some sinkholes or subsidence take place from time to time in the areas where abandoned room and pillar type mines exist. The author has been involved with the stability of abandoned mines beneath urbanized residential areas in Tokai region and there is a great concern about the stability of these abandoned mines during large earthquakes as well as in the long term. The 2003 Miyagi Hokubu and 2011 Great East Japan earthquakes caused great damage to abandoned mines and resulted in many collapses. The author presents the effect of the depth and groundwater on the formation of sinkholes or ground subsidence associated with abandoned room and pillar lignite mines under static and dynamic conditions and discusses the implications on the areas above abandoned lignite mines in this paper.

Analytical investigation of lignite and its ash samples taken from the Afsin-Elbistan coal basin in Turkey

Energy Technology Data Exchange (ETDEWEB)

Kucukonder, Adnan; Paksoy, Emine; Biber, Seyma [Kahramanmaras Suetcue Imam Univ. (Turkey). Dept. of Physics; Durdu, Burhanettin Goeker [Kilis 7 Aralik Univ., Kilis (Turkey). Opticianry Program; Baskaya, H.; Dogru, Mahmut [Bitlis Eren Univ. (Turkey). Dept. of Physics

2014-04-15

Lignite, taken from basin in Afsin-Elbistan region, and ash samples were analyzed according to the qualitative, quantitative and radioactivity properties. An elemental analysis was made by using the Energy Dispersive X-Ray Fluorescence (EDXRF) technique. 59.5 keV photons emitted from a {sup 241}Am source and 5.9 keV photons emitted from a {sup 55}Fe radioactive source were used for excitation. The characteristic K X-rays of the elements were counted with a Si(Li) detector. For the same samples gross alpha, gross beta and radionuclide activities were also measured. (orig.)

Co-combustion of low rank coal/waste biomass blends using dry air or oxygen

International Nuclear Information System (INIS)

Haykiri-Acma, H.; Yaman, S.; Kucukbayrak, S.

2013-01-01

Biomass species such as the rice husk and the olive milling residue, and a low quality Turkish coal, Soma Denis lignite, were burned in a thermal analyzer under pure oxygen and dry air up to 900 °C, and differential thermal analysis (DTA) and derivative thermogravimetric (DTG) analysis profiles were obtained. Co-combustion experiments of lignite/biomass blends containing 5–20 wt% of biomass were also performed. The effects of the oxidizer type and the blending ratio of biomass were evaluated considering some thermal reactivity indicators such as the maximum burning rate and its temperature, the maximum heat flow temperature, and the burnout levels. FTIR (Fourier transform infrared) spectroscopy and SEM (scanning electron microscopy) were used to characterize the samples, and the variations in the combustion characteristics of the samples were interpreted based on the differences in the intrinsic properties of the samples. - Highlights: ► Co-combustion of lignite/biomass blends. ► The effects of the oxidizer type and the blending ratio. ► Effects of intrinsic properties on combustion characteristics.

Comparative analysis of possibilities for raising the efficiency in thermal power plant by utilisation of waste heat energy

Directory of Open Access Journals (Sweden)

Mijakovski Vladimir

2016-01-01

Full Text Available The possibility to use flue gases waste heat for increasing the efficiency of thermal power plant (TPP explained in this work refers to lignite fired TPP-Bitola in Macedonia (3x233 MW installed electric capacity. Possibility to utilize low-temperature heat energy at the plant’s cold end is also considered in the analysis. Specific fuel consumption is used as an analysis and comparison parameter. Its reduction, compared to the basic power unit ranges between 0.4% and 3.4%. An analysis presenting economic feasibility of the low-temperature heat energy utilization concept for two different refrigerants used in the heat pump is also presented.

Nanofluids with plasma treated diamond nanoparticles

International Nuclear Information System (INIS)

Yu Qingsong; Kim, Young Jo; Ma Hongbin

2008-01-01

In this study, diamond nanoparticles were plasma treated by glow discharges of methane and oxygen with an aim of improving their dispersion characteristics in a base fluid of water and enhancing the thermal conductivity of the resulting nanofluids. It was found that, after plasma treatment, stable nanofluids with improved thermal conductivity were obtained without using any stabilizing agents. With <0.15 vol % addition of plasma treated nanoparticles into water, a 20% increase in thermal conductivity was achieved and a 5%-10% increase in both fluid density and viscosity was observed

Regional Studies Program. Extraction of North Dakota lignite: environmental and reclamation issues

Energy Technology Data Exchange (ETDEWEB)

LaFevers, J.R.; Johnson, D.O.; Dvorak, A.J.

1976-12-01

This study, sponsored by the U.S. Energy Research and Development Administration, addresses the environmental implications of extraction of coal in North Dakota. These implications are supported by details of the geologic and historical background of the area of focus, the lignite resources in the Fort Union coalfield portion. The particular concentration is on the four-county area of Mercer, Dunn, McLean, and Oliver where substantial coal reserves exist and a potential gasification plant site has been identified. The purposes of this extensive study are to identify the land use and environmental problems and issues associated with extraction; to provide a base of information for assessing the impacts of various levels of extraction; to examine the economics and feasibility of reclamation; and to identify research that needs to be undertaken to evaluate and to improve reclamation practices. The study also includes a description of the physical and chemical soil characteristics and hydrological and climatic factors entailed in extraction, revegetation, and reclamation procedures.

Light absorption by primary particle emissions from a lignite burning plant

International Nuclear Information System (INIS)

Bond, T.C.; Bussemer, M.; Wehner, B.; Keller, S.; Charlson, R.J.; Heintzenberg, J.

1999-01-01

Anthropogenic aerosols from the burning of fossil fuels contribute to climate forcing by both scattering and absorbing solar radiation, and estimates of climate forcing by light-absorbing primary particles have recently been published. While the mass and optical properties of emissions are needed for these studies, the available measurements do not characterize the low-technology burning that is thought to contribute a large fraction of light-absorbing material to the global budget. The authors have measured characteristics of particulate matter (PM) emitted from a small, low-technology lignite-burning plant. The PM emission factor is comparable to those used to calculate emission inventories of light-absorbing particles. However, the fine fraction, the absorbing fraction, and the absorption efficiency of the emissions are substantially below assumptions that have been made in inventories of black carbon emissions and calculations of climate forcing. The measurements suggest that nonblack, light-absorbing particles are emitted from low-technology coal burning. As the burning rate increases, the emitted absorption cross-section decreases, and the wavelength dependence of absorption becomes closer to that of black particles

Time-dependent phosphate dynamics in reclaimed lignite-mine soils under Robinia pseudoacacia L.

Science.gov (United States)

Freese, Dirk; Slazak, Anna

2017-04-01

As a consequence of the opencast lignite mining activities in Lusatia/Germany, the cultivation of Short Rotation Coppice plantations (SRC) has been considered as a viable option for reclamation purposes. In this region an area of about 1000 km2 has been degraded. Owing to the unfavourable biotic and abiotic properties of the overburden mining substrate, the biogeochemical processes associated with the soil ecosystem development are in the initial phase. The substrate contains very low amount of nutrients, mainly very low total Phosphate (P) content nearly equal to zero. The lack of P is one of the main issues in reclamation of this marginal site. Therefore, the cultivation of perennial SRC with Robinia pseudoacacia L. is considered as a supporting measurement for effective soil reclamation. In this context, it is important to understand the dynamics of P in this "initial substrate" to describe the P availability and P sorption/desorption.. Iron/aluminium oxides and organic matter are the soil constituents most strongly affecting the reactions and rate of P sorption and desorption, also in post-mining soils. Therefore the interaction of these oxides and organic matter with P is essential with regard to developing effective nutrient management strategies for marginal sites. The study focused on P sorption and desorption with regard to different development stages of R. pseudoacacia L. established in a short rotation coppices on the post mining soils. to describe the P availability (Pav) in relation to total P mobility. The hypothesis is that SRC would cause significant changes in soil P dynamics over time in post lignite mining soils. The trees has been planted in between 1995 and 2007, which means that R. pseudoacacia L. was in a range of 2 to 20 years old at different sampling times. Soil was sampled in 2008 and 2015 at three depths of: 0-3cm, 3-10 cm and 10-30 cm. To characterize the P dynamics different P forms and P sorption/desorption kinetics were analysed

Evaluating Lignite-Derived Products (LDPs) for Agriculture - Does Research Inform Practice?

Science.gov (United States)

Patti, Antonio; Rose, Michael; Little, Karen; Jackson, Roy; Cavagnaro, Timothy

2014-05-01

Lignite-derived products (LDPs), including humic acids and organo-mineral soil conditioners, are being marketed in many parts of the world. They are promoted as plant growth stimulants, additives that improve plant nutrient uptake as well as providing humic materials to improve soil structure and combat soil degradation. There are mixed views regarding the efficacy of these products and there is a lack of scientific studies that verify the efficacy of these products in the field. Anecdotally, agricultural producers become repeat users of the products when they see economic benefits, such as increases in crop yields, while others abandon repeat use when no benefits were seen. In this paper, we present results from a literature meta-analysis1 and a number of field studies that examine the potential for LDPs to improve soil fertility and plant growth. Our findings suggest that complex interactions between LDPs, soil types, environmental conditions and plant species mean that a 'one-size fits all' product or solution is unlikely; and that changes to soil characteristics brought about by LDPs are more apparent over longer time periods than a single cropping season. Most of these studies have not been undertaken in full field trial conditions, where the crop has been grown to harvest. Limited studies in small plots or glass-house conditions often report early benefits. It is not known if these benefits persist. Moreover, the actual composition of these additives may vary significantly and is rarely specified in full. In a study of our own, a small plot experiment evaluated the effect of a single application of a commercial potassium humate product from Victorian lignite on ryegrass and lucerne grown in a sandy, nutrient deficient, low organic matter soil. Treatment resulted in increased shoot growth (up to 33%) of ryegrass during the pasture establishment phase. Root growth was also improved with a 47% increase at 0-10 cm depth and 122% increase at 10-30 cm depth

Studies on mechanical, thermal and dynamic mechanical properties of untreated (raw) and treated coconut sheath fiber reinforced epoxy composites

International Nuclear Information System (INIS)

Suresh Kumar, S.M.; Duraibabu, D.; Subramanian, K.

2014-01-01

Highlights: • UTCSE and TCSE composites have been fabricated by compression molding technique. • The prepared specimens were characterized by FTIR, DMA, TGA and SEM techniques. • TCSE composite showed higher mechanical properties compared to UTCSE composite. • DMA showed that TCSE composite exhibited higher storage modulus than UTCSE composite. • TCSE composite showed higher thermal stability than UTCSE composite. - Abstract: The untreated (raw) coconut sheath fiber reinforced epoxy (UTCSE) composite and treated coconut sheath fiber reinforced epoxy (TCSE) composite have been fabricated using hand layup followed by compression molding technique. The prepared specimens were characterized by Fourier transform infrared spectroscopy (FTIR), dynamic mechanical analysis (DMA), thermo gravimetric analysis (TGA) and scanning electron microscopy (SEM) techniques. The prepared specimens are cut as per ASTM Standards to measure tensile, flexural and impact strengths by using universal testing machine and izod impact tester respectively. The treated coconut sheath fiber reinforced epoxy composite (TCSE) posses higher mechanical strength and thermal stability compared to untreated (raw) coconut sheath fiber reinforced epoxy composite (UTCSE). In the SEM fracture analysis, TCSE composite showed better fiber–matrix bonding and absence of voids compared to UTCSE composite

Installation services in the lignite industry. Implementing health and safety; Montageeinsaetze in der Braunkohlenindustrie. Handlungsfeld fuer den Arbeitsschutz

Energy Technology Data Exchange (ETDEWEB)

Roskopf, Norbert [Roskopf Vulkanisation GmbH, Aachen (Germany)

2011-07-01

The increasing number of assignments of contractors in the lignite industry challenges both the client and the contractor with respect to health and safety. Additional endeavours have to be made concerning information, communication, coordination and assurance. Quantitative differences of occupational safety can be made up by operator support. The contractor himself is required to highly focus on health and safety issues. The European Agency for Safety and Health at Work (EU OSHA) and its campaign 'Healthy Workplaces - Safe Maintenance' currently raises the awareness of all parties being involved. More information can be found under http://hw.osha.europa.eu. (orig.)

Morphology and gas sensing properties of as-deposited and thermally treated doped thin SnO{sub x} layers

Energy Technology Data Exchange (ETDEWEB)

Georgieva, B; Pirov, J; Podolesheva, I [Acad. J. Malinowski Central Laboratory of Photoprocesses, Bulgarian Academy of Sciences, Acad. G. Bonchev Str., Bl.109, 1113 Sofia (Bulgaria); Nihtianova, D, E-mail: biliana@clf.bas.b [Central Laboratory of Mineralogy and Crystallography, Bulgarian Academy of Sciences, Acad. G. Bonchev Str., Bl.107, 1113 Sofia (Bulgaria)

2010-04-01

Thin layers intended for gas sensors are prepared by vacuum co-evaporation of TeO{sub 2} and Sn. The as-deposited layers consist of a nanosized oxide matrix and finely dispersed dopants (Te, Sn, TeO{sub 2} or SnTe, depending on the atomic ratio R{sub Sn/Te}). In order to improve the characteristics of the layers they are additionally doped with platinum. The gas sensing properties are strongly dependent on the atomic ratio R{sub Sn/Te}, as well as on the structure, composition and surface morphology. The as-deposited layers with R{sub Sn/Te} 0.8 are highly sensitive humidity sensors working at room temperature. Thermally treated Pt-doped layers with R{sub Sn/Te} 2.3 are promising as ethanol sensors. With the aim of obtaining more detailed knowledge about the surface morphology, structure and composition of layers sensitive to different environments, various techniques -TEM, SAED, SEM, EDS in SEM and white light interferometry (WLI), are applied. It is shown that all layers with 1.0 > R{sub Sn/Te} > 2, as-deposited and thermally treated, exhibit a columnar structure and a very smooth surface along with the nanograined matrix. The thermal treatment causes changes in the structure and composition of the layers. The ethanol-sensitive layers consist of nanosized polycrystalline phases of SnO{sub 2}, Sn{sub 2}O{sub 3}, Sn{sub 3}O{sub 4} and TeO{sub 2}. This knowledge could help us understand better the behaviour and govern the characteristics of layers obtained by co-evaporation of Sn and TeO{sub 2}.

Introduction of renewable energy sources in the district heating system of Greece

Directory of Open Access Journals (Sweden)

Nikolaos Margaritis

2016-06-01

Full Text Available The district heating (DH system of Greece, mainly supported from lignite fired stations, is facing lately significant challenges. Stricter emission limits, decreased efficiency due to old age and increased costs are major challenges of the lignite sector and are expected to result in the decommissioning of several lignite-fired units in the coming years. As a result, managers of DH networks are currently investigating alternative scenarios for the substitution of thermal power that it is expected to be lost, through the integration of Renewable Energy Sources (RES into the system. In this paper, the DH systems of Kozani and Ptolemaida are examined regarding possible introduction of RES. The first study examines district heating of Kozani and alternative future options for covering a part of city’s thermal load whereas the second study refers to a biomass CHP plant (ORC technology, 1MWe, 5MWth to be powered from a biomass mixture (wood chips and straw.

Treat upgrade fuel fabrication

International Nuclear Information System (INIS)

Davidson, K.V.; Schell, D.H.

1979-01-01

An extrusion and thermal treatment process was developed to produce graphite fuel rods containing a dispersion of enriched UO 2 . These rods will be used in an upgraded version of the Transient Reactor Test Facility (TREAT). The improved fuel provides a higher graphite matrix density, better fuel dispersion and higher thermal capabilities than the existing fuel

Removal of pharmaceuticals, perfluoroalkyl substances and other micropollutants from wastewater using lignite, Xylit, sand, granular activated carbon (GAC) and GAC+Polonite® in column tests - Role of physicochemical properties.

Science.gov (United States)

Rostvall, Ande; Zhang, Wen; Dürig, Wiebke; Renman, Gunno; Wiberg, Karin; Ahrens, Lutz; Gago-Ferrero, Pablo

2018-06-15

This study evaluated the performance of five different sorbents (granular activated carbon (GAC), GAC + Polonite ® (GAC + P), Xylit, lignite and sand) for a set of 83 micropollutants (MPs) (pharmaceuticals, perfluoroalkyl substances (PFASs), personal care products, artificial sweeteners, parabens, pesticide, stimulants), together representing a wide range of physicochemical properties. Treatment with GAC and GAC + P provided the highest removal efficiencies, with average values above 97%. Removal rates were generally lower for Xylit (on average 74%) and lignite (on average 68%), although they proved to be highly efficient for a few individual MPs. The average removal efficiency for sand was only 47%. It was observed that the MPs behaved differently depending on their physicochemical properties. The physicochemical properties of PFASs (i.e. molecular weight, topological molecular surface area, log octanol water partition coefficient (K ow ) and distribution coefficient between octanol and water (log D)) were positively correlated to observed removal efficiency for the sorbents Xylit, lignite and sand (p < 0.05), indicating a strong influence of perfluorocarbon chain length and associated hydrophobic characteristics. In contrast, for the other MPs the ratio between apolar and polar surface area (SA/SP) was positively correlated with the removal efficiency, indicating that hydrophobic adsorption may be a key feature of their sorption mechanisms. GAC showed to be the most promising filter medium to improve the removal of MPs in on-site sewage treatment facilities. However, more studies are needed to evaluate the removal of MPs in field trials. Copyright © 2018 Elsevier Ltd. All rights reserved.

Factors of Reclamation Success at the Lignite Strip-Mined Land in Northern Greece

Directory of Open Access Journals (Sweden)

Thomas Panagopoulos

2013-06-01

Full Text Available The adverse ecological conditions at the lignite mines of Ptolemaida make the landscape reclamation difficult. The naturally established vegetation and soil properties were studied prior to reclamation. Various forest species were planted to assess the afforestation potential. The natural vegetation was heterogeneous but can be used for the analysis of the site. The soil of the spoil heaps was heterogeneous with unfavourable physicochemical properties. Surface soil temperature was still 24º C higher in bare soil than in soil covered with vegetation. The most successful species of the afforestation trial were Robinia pseudoacacia and Cedrus atlantica. Covering of fly ash spoils with topsoil presented poor results, while sewage sludge gave a favorable amelioration response in areas with high fly ash content. Topsoil from older stands was the suggested method to establish Robinia pseudoacacia. Reclamation success was dependent on appropriate planning; thus, the new landscape had to be designed in harmony with the surrounding landscape before the start of the mining activity.

NO formation during oxy-fuel combustion of coal and biomass chars

DEFF Research Database (Denmark)

Zhao, Ke; Jensen, Anker Degn; Glarborg, Peter

2014-01-01

The yields of NO from combustion of bituminous coal, lignite, and biomass chars were investigated in O2/N2 and O2/CO 2 atmospheres. The experiments were performed in a laboratory-scale fixed-bed reactor in the temperature range of 850-1150 °C. To minimize thermal deactivation during char preparat......The yields of NO from combustion of bituminous coal, lignite, and biomass chars were investigated in O2/N2 and O2/CO 2 atmospheres. The experiments were performed in a laboratory-scale fixed-bed reactor in the temperature range of 850-1150 °C. To minimize thermal deactivation during char...

Structure and wettability property of the growth and nucleation surfaces of thermally treated freestanding CVD diamond films

Science.gov (United States)

Pei, Xiaoqiang; Cheng, Shaoheng; Ma, Yibo; Wu, Danfeng; Liu, Junsong; Wang, Qiliang; Yang, Yizhou; Li, Hongdong

2015-08-01

This paper reports the surface features and wettability properties of the (1 0 0)-textured freestanding chemical vapor deposited (CVD) diamond films after thermal exposure in air at high temperature. Thermal oxidation at proper conditions eliminates selectively nanodiamonds and non-diamond carbons in the films. The growth side of the films contains (1 0 0)-oriented micrometer-sized columns, while its nucleation side is formed of nano-sized tips. The examined wettability properties of the as-treated diamond films reveal a hydrophilicity and superhydrophilicity on the growth surface and nucleation surface, respectively, which is determined by oxygen termination and geometry structure of the surface. When the surface termination is hydrogenated, the wettability of nucleation side converted from superhydrophilicity to high hydrophobicity, while the hydrophilicity of the growth side does not change significantly. The findings open a possibility for realizing freestanding diamond films having not only novel surface structures but also multifunction applications, especially proposed on the selected growth side or nucleation side in one product.

Task 50 - deposition of lignites in the Fort Union Group and related strata of the northern Great Plains

Energy Technology Data Exchange (ETDEWEB)

Hartman, J.H.; Roth, B.; Kihm, A.J.

1997-08-11

Late Cretaceous, Paleocene, and early Eocene geologic and paleontologic studies were undertaken in western North Dakota, eastern and south-central Montana, and northwestern and northeastern Wyoming. These study areas comprise the Williston, Bighorn, and Powder River Basins, all of which contain significant lignite resources. Research was undertaken in these basins because they have the best geologic sections and fossil record for the development of a chronostratigraphic (time-rock) framework for the correlation of lignite beds and other economic resources. A thorough understanding of the precise geologic age of the deposition of sediments permits a powerful means of interpreting the record of geologic events across the northern Great Plains. Such an understanding allows for rigorous interpretation of paleoenviromnents and estimates of resource potential and quality in this area of economically significant deposits. This work is part of ongoing research to document change in the composition of molluscan fossil faunas to provide a paleoenvironmentally sensitive independent means of interpreting time intervals of brief duration during the Late Cretaceous, Paleocene, and Eocene. This study focuses on the record of mollusks and, to a lesser extent, mammals in the (1) Hell Creek-Tullock Formations, which include the Cretaceous-Paleocene boundary, in the western portion of the Williston Basin, Montana; (2) uppermost Cretaceous, Paleocene, and lowermost Eocene strata in western North Dakota, which -includes the last interior seaway in North Dakota; (3) upper Paleocene and lowermost Eocene of the northern portion of the Bighorn Basin of south-central Montana and northwestern Wyoming; and (4) Powder River Basin of northeastern Wyoming and southeastern Montana. The geologic record provides different physical and paleontological information to aid in interpreting the geologic record through the study interval.

Volatility and leachability of heavy metals and radionuclides in thermally treated HEPA filter media generated from nuclear facilities

International Nuclear Information System (INIS)

Yoon, In-Ho; Choi, Wang-Kyu; Lee, Suk-Chol; Min, Byung-Youn; Yang, Hee-Chul; Lee, Kune-Woo

2012-01-01

Highlights: ► Thermally treated HEPA filter media was transformed into glassy bulk materials. ► Main radionuclide and heavy metal were Cs-137 and Zn. ► Cs and Zn were transformed into stable form without volatilization and leaching. ► The proposed technique is simple and energy efficient procedure. - Abstract: The purpose of the present study was to apply thermal treatments to reduce the volume of HEPA filter media and to investigate the volatility and leachability of heavy metals and radionuclides during thermal treatment. HEPA filter media were transformed to glassy bulk material by thermal treatment at 900 °C for 2 h. The most abundant heavy metal in the HEPA filter media was Zn, followed by Sr, Pb and Cr, and the main radionuclide was Cs-137. The volatility tests showed that the heavy metals and radionuclides in radioactive HEPA filter media were not volatilized during the thermal treatment. PCT tests indicated that the leachability of heavy metals and radionuclides was relatively low compared to those of other glasses. XRD results showed that Zn and Cs reacted with HEPA filter media and were transformed into crystalline willemite (ZnO·SiO 2 ) and pollucite (Cs 2 OAl 2 O 3 4SiO 2 ), which are not volatile or leachable. The proposed technique for the volume reduction and transformation of radioactive HEPA filter media into glassy bulk material is a simple and energy efficient procedure without additives that can be performed at relatively low temperature compared with conventional vitrification process.

Structural insights from boron tribromide ether cleavage into lignites and low maturity coals from the New Zealand Coal Band

DEFF Research Database (Denmark)

Glombitza, Clemens; Mangelsdorf, Kai; Horsfield, Brian

2011-01-01

structure, boron tribromide (BBr3) ether cleavage was applied to a series of lignite and coal samples of different maturity (R0 0.27–0.80%) obtained from coal mines and natural outcrops from the North and South Island of New Zealand. Terminal ether-bound alcohols rapidly decrease during diagenesis and occur...... over geological time scales. Polyether compounds were detected with chain length up to five carbon atoms. After a small decrease during the diagenetic phase these compounds occur in relatively high concentrations, even in the main catagenetic stage. This suggests that these linkage structures represent...

Processing of baby food using pressure-assisted thermal sterilization (PATS) and comparison with thermal treatment

Science.gov (United States)

Wang, Yubin; Ismail, Marliya; Farid, Mohammed

2017-10-01

Currently baby food is sterilized using retort processing that gives an extended shelf life. However, this type of heat processing leads to reduction of organoleptic and nutrition value. Alternatively, the combination of pressure and heat could be used to achieve sterilization at reduced temperatures. This study investigates the potential of pressure-assisted thermal sterilization (PATS) technology for baby food sterilization. Here, baby food (apple puree), inoculated with Bacillus subtilis spores was treated using PATS at different operating temperatures, pressures and times and was compared with thermal only treatment. The results revealed that the decimal reduction time of B. subtilis in PATS treatment was lower than that of thermal only treatment. At a similar spore inactivation, the retention of ascorbic acid of PATS-treated sample was higher than that of thermally treated sample. The results indicated that PATS could be a potential technology for baby food processing while minimizing quality deterioration.

Development of the fluidized bed thermal treatment process for treating mixed waste

International Nuclear Information System (INIS)

Semones, G.B.; Williams, P.M.; Stiefvater, S.P.; Mitchell, D.L.; Roecker, B.D.

1993-01-01

A fluidized bed system is being developed at Rocky Flats for the treatment of mixed waste (a mixture of radioactive and chemically hazardous waste). The current program builds on experience gained in the 1970's and 1980's in tests with bench-scale, pilot-scale, and demonstration-scale fluidized bed systems. The system operates at low temperatures (∼ 525--600 degree C) which eliminates many of the disadvantages associated with high temperature thermal treatment processes. The process has shown the ability to destroy polychlorinated biphenyls (PCB's) with 99.9999% (''six-nines'') destruction efficiency in tests monitored by the Environmental Protection Agency (EPA). The bed makes use of in situ neutralization of acidic off-gases by incorporating sodium carbonate (Na 2 CO 3 ) in the bed media. This eliminates using wet scrubbers to treat the off-gas; these produce a high volume of secondary waste. Once in operation, it is expected that the fluidized bed process will yield up to a 40:1 reduction in the volume of the waste

2015 Plan. Project 4: electric power supply, technologies, cost and availability. Sub-project alternative energy sources: solar, eolic, shale, ocean, hydrogen, organic wastes, peat and lignite

International Nuclear Information System (INIS)

1993-07-01

Several aspects of solar, eolic and ocean energy and shale, peat lignite, hydrogen and organic waste in Brazil are described, including reserves, potential, technology economy and environment. Based in data and information presented in this report, the necessity of a more detailed survey with the potential of alternative energy sources in Brazil, emphasizing the more promiser regions is also mentioned. (C.G.C.)

Survival and growth of Alfalfa (Medicago sativa l.) inoculated with an am fungus (Glomus intraradices) in contaminated soils treated with two different remediation technologies (bio-pile and thermal desorption)

International Nuclear Information System (INIS)

Norini, M.P.; Beguiristain, Th.; Leyval, C.

2005-01-01

Polycyclic aromatic hydrocarbons (PAHs) represent a group of persistent and toxic soil pollutants that are of major public concern due to their mutagenic and carcinogenic property. Phyto-remediation is the use of plants and their associated microorganisms for remediation of polluted soils. Phyto-remediation could be used in conjunction with other remediation technologies to reduce the contamination to safe levels and maintain or restore soil physico-chemical and biological properties. Most plant species form mycorrhizas with symbiotic fungi. It was shown that AM fungi enhance survival and plant growth in PAH contaminated soils. Mycorrhizal fungi also enhance the biotransformation or biodegradation of PAH, although the effect differed between soils. A rhizosphere and myco-rhizosphere gradient of PAH concentrations was observed, with decreased PAH concentration with decreased distance to roots. Different microbial communities were found in the rhizosphere of AM and non-mycorrhizal plants in comparison to bulk soil, suggesting that AM could affect PAH degradation by changing microbial communities. We investigated the effect of mycorrhizal fungi and nutrients on the ability of alfalfa to grow on soil contaminated with PAHs before and after two remediation treatments. We used soil from an industrial site (Homecourt, North East part of France) highly contaminated with PAH (2000 mg kg -1 ), which has been partially treated by two different remediation technologies (bio-pile and thermal desorption). The bio-pile treatment consisted of piling the contaminated soil with stimulation of aerobic microbial activity by aeration and addition of nutrient solution, and reduced PAH concentration to around 300 mg kg-1. With the thermal desorption treatment the soil was heated to around 500 deg. C so that PAH vaporized and were separated from the soil. The residual PAH concentration in soil was 40 mg kg -1 . Treated and non-treated contaminated soil was planted with alfalfa (Medicago

Slope stability in opencast lignite mining in Spain. Estabilidad de taludes en la mineria de lignito a cielo abierto en Espana

Energy Technology Data Exchange (ETDEWEB)

1987-01-01

The present study assesses the current state of opencast workings in their respective geological and geographical situations and attempts to establish a set of general design criteria for each site according to its location. Six zones were selected in the three principal lignite-producing areas of Spain, two in Galicia - Puentes de Garcia Rodriguez (ENDESA) and Meirama (LIMEISA); three in Teruel - Alloza (ENDESA) Sabina and Yermegada (MFUSA); one in Mallorca - Jupiter (LIGNITOS SA). Two sites not yet in operation were also studied: Barrabasa in Teruel and Lloseta in Mallorca. 60 figs., 25 tabs.

Application of Thermal Desorption Unit (TDU) to treat low-toxicity mineral oil base cuttings in Barinas District, Venezuela

Energy Technology Data Exchange (ETDEWEB)

Rendon, Ruben [Petroleos de Venezuela, Caracas (Venezuela); Luzardo, Janeth; Alcoba, Alcides [M-I SWACO, Houston, TX (United States)

2008-07-01

The potential environmental impact of oil-based drill cuttings is generating increased scrutiny in the oil and gas industry. If left untreated, oil-based cuttings not only increase the risk of environmental liabilities, but also affect revenue, as drilling generates wastes that in most cases require special treatment before disposal. Consequently, the oil industry is looking for technologies to help minimize environmental liabilities. Accordingly, the Barinas District of PDVSA has started a pilot trial to treat oil-based drilling cuttings by applying thermal desorption technology. The main objective of this technology is recovering trapped hydrocarbons, while minimizing wastes and preparing solids to be disposed of through a mobile treatment plant. This novel technology has been used worldwide to treat organic pollutants in soil. Thermal desorption is a technology based on the application of heat in soils polluted with organic compounds. With this technology, target temperatures vary according to the type and concentration of detected pollutants along with its characterization, in such a way that compounds are disposed of by volatilization. As part of the integral waste management development along with the pilot trial for hydrocarbon-contaminated solid waste treatment, trials on soils were undertaken by applying process-generated ashes in equally-sized bins, with different mixtures (ashes, ashes organic material, ashes-organic material-sand, ashes-land). The resulting process offers an immediate soil remediation and final disposal solution for toxic and dangerous waste. (author)

Coal consumption minimizing by increasing thermal energy efficiency at ROMAG-PROD Heavy Water Plant

International Nuclear Information System (INIS)

Preda, Marius Cristian

2006-01-01

ROMAG-PROD Heavy Water Plant is a large thermal energy consumer using almost all the steam output from ROMAG-TERMO Power Plant - the steam cost weight in the total heavy water price is about 40%. The steam consumption minimizing by modernization of isotopic exchange facilities and engineering development in ROMAG-PROD Heavy Water Plant results in an corresponding decrease of coal amount burned at ROMAG-TERMO boilers. This decrease could be achieved mainly by the followings ways: - Facility wrappings integrity; - High performance heat exchangers; - Refurbished heat insulations; - Modified condenser-collecting pipeline routes; - High performance steam traps; - Heat electric wire. When coal is burned in Power Plant burners to obtain thermal energy, toxic emissions results in flue gases, such as: - CO 2 and NO x with impact on climate warming; - SO 2 which results in ozone layer thinning effect and in acid rain falls. From the value of steam output per burned coal: 1 GCal steam = 1.41 tone steam = 0.86 thermal MW = 1.1911 tones burned coal (lignite), it is obvious that by decreasing the thermal energy consumption provided for ROMAG PROD, a coal amount decrease is estimated at about 45 t/h, or about 394,200 t/year coal, which means about 10% of the current coal consumption at ROMAG-TERMO PP. At the same time, by reducing the burned coal amount, an yearly decrease in emissions into air to about 400,000 tones CO 2 is expected

Black coal and lignite from biomass as fuel or alternative to carbon dioxide capture and storage; Stein- und Braunkohle aus Biomasse als Brennstoff oder als Alternative zur CO{sub 2}-Abscheidung und -Speicherung

Energy Technology Data Exchange (ETDEWEB)

Stengl, S.; Koch, C.; Scheer, J.; Stadlbauer, E.A.; Richarts, F.; Altensen, R.; Richter, H. [Technische Hochschule Mittelhessen (THM), Giessen (Germany); Weber, B. [Universidad Autonoma del Estado de Mexico (UAEM), Toluca (Mexico). Facultad de Ingenieria; Bayer, M.P.; Albert, K. [Tuebingen Univ. (Germany). Inst. fuer Organische Chemie

2012-05-15

This article refers to coalification of biomass in light of embedding this technique in the regional material flow management. From a process engineering point of view the focus is set on Hydrothermal Carbonization (HTC) and Low Temperature Conversion (LTC). Based on monosaccharides as building blocks of polysaccharides and ligneous biomass, the thermal behavior of glucose, fructose and xylose depending on reaction time and temperature is tracked. Consequently mainly hemicellulosic structures are affected under HTC conditions. However LTC converts both hemicelluloses as well as cellulose. The classification of HTC and LTC products from spent grains in terms of H/C and C/O ratio according to Meunier's coalification diagram ranges HTC coal in the area of lignite and the LTC coal in the area of black coal. This grading in terms of elementary analysis is confirmed by solid state{sup 13}C-NMR spectroscopy. The spectrum of LTC coal from spent grains fashioned at 400 C for duration of 3 h is undistinguishable from the spectrum of black coal. From the chemical point of view these two coals has to be described as identical. However the spectrum of the HTC product made of spent grains fashioned at 250 C for 3 h in a pressurized environment shows similarity to the spectrum of lignite. As engineering usage HTC products are a tool to convert cellulose-based residues in a uniform, high-energy matter for incineration processes. For this in-house waste management of e.g. breweries or sugar refineries could be enhanced. LTC coals are due to their stability eligible to extract CO{sub 2} from the atmosphere via photosynthesis and transfer carbon to the long-term stable geological cycle of matter. Consequential LTC offers an alternative to CCS. As a side effect LTC coals contribute to the elevation of carbon content in soils, which facilitates their water-holding and nutrient-holding capacity. (orig.)

Quantitative spectrographic determination of traces of germanium in lignite; Determinacion Espectrografica Cuantitativa de trazas de Germanio en Lignitos

Energy Technology Data Exchange (ETDEWEB)

Martin, M; Roca, M

1972-07-01

A burning technique in a d.c. arc at 10 amp has been employed. The standards have been prepared from a natural lignite with a low germanium content. In order to enhance sensitivity, AgCl, K{sub 2}SO{sub 4}, CuF{sub 2}, Sb{sub 2}S{sub 3} and Bi{sub 2}S{sub 3} have been tested as sweeping materials. Using 2% CuF{sub 2} a detection limit of 1 ppm germanium is attainable. Bi, Cu, Sb and Sn have been studied as internal standards: the former leads to the, highest precision (1 6%). Results show good agreement with those obtained by the addition method. (Author) 6 refs.

Remedial Action Plan for stabilization of the inactive uraniferous lignite processing sites at Belfield and Bowman, North Dakota

International Nuclear Information System (INIS)

1990-12-01

This remedial action plan (RAP) has been developed to serve a threefold purpose. It presents the series of activities that are proposed by the US Department of Energy (DOE) to accomplish long-term stabilization and control of radioactive materials at the inactive uraniferous lignite processing sites at Belfield and near Bowman (at the former Griffin town site), North Dakota. It provides a characterization of the present conditions of the sites. It also serves to document the concurrence of the state of North Dakota and the US Nuclear Regulatory Commission (NRC) in the remedial action. This agreement, upon execution by the DOE and the state of North Dakota and concurrence by the NRC, becomes Appendix B of the Cooperative Agreement

FLAMMABILITY OF HERBICIDE-TREATED GUAVA FOLIAGE

Science.gov (United States)

Guava leaves treated with herbicide were found to be less flammable than untreated green leaves or dead leaves . Differences in flammability were...determined by small-scale laboratory fires, differential thermal analysis, and thermogravimetric analysis. The herbicide-treated leaves had a higher ash

EFFECTS OF SODIUM AND CALCIUM IN LIGNITE ON THE PERFORMANCE OF ACTIVATED CARBON PRODUCTS; TOPICAL

International Nuclear Information System (INIS)

Edwin S. Olson; Kurt E. Eylands; Daniel J. Stepan

2001-01-01

New federal drinking water regulations have been promulgated to restrict the levels of disinfection by-products (DBPs) in finished public water supplies. DBPs are suspected carcinogens and are formed when organic material is partially oxidized by disinfectants commonly used in the water treatment industry. Additional federal mandates are expected in the near future that will also affect public water suppliers with respect to DBPs. These new federal drinking water regulations may require public water suppliers to adjust treatment practices or incorporate additional treatment operations into their existing treatment trains. Many options have been identified, including membrane processes, granular activated carbon, powered activated carbon (PAC), enhanced coagulation and/or softening, and alternative disinfectants (e.g., chlorine dioxide, ozone, and chloramines). Of the processes being considered, PAC appears to offer an attractive benefit-to-cost advantage for many water treatment plants, particularly small systems (those serving fewer than 10,000 customers). PAC has traditionally been used by the water treatment industry for the removal of compounds contributing to taste and odor problems. PAC also has the potential to remove naturally occurring organic matter (NOM) from raw waters prior to disinfection, thus controlling the formation of regulated DBPs. Many small water systems are currently using PAC for taste and odor control and have the potential to use PAC for controlling DBPs. Activated carbons can be produced from a variety of raw materials, including wood, peat, coconut husks, and numerous types of coal. The Energy and Environmental Research Center (EERC) has been working on the development of a PAC product to remove NOM from surface water supplies to prevent the formation of carcinogenic DBPs during chlorination. During that study, the sodium and calcium content of the lignites showed a significant effect on the sorption capacity of the activated carbon

Hydropyrolysis of a Turkish lignite (Tuncbilek) and effect of temperature and pressure on product distribution

Energy Technology Data Exchange (ETDEWEB)

Canel, M.; Misirlioglu, Z.; Sinag, A. [Ankara University, Ankara (Turkey). Faculty of Science

2005-08-01

The hydropyrolysis of a Turkish lignite (Tuncbilek) in a swept fixed bed reactor connected with a thermo-balance was performed at a heating rate of 3 C/min up to 950 C under 0.5MPa, 1MPa and 10MPa hydrogen pressures. The formation rates of gaseous hydrocarbons, carbon oxides, water and tar were determined. The difference between the weight loss due to tar formation of the non-condensable total and the weight loss of the sample recorded continuously with the thermo-balance showed the corresponding curve of tar formation rate as a function of temperature. It was shown that the total conversion and the formation rate of the products during hydropyrolysis could be influenced by varying the pressure. On the other hand, the volatile matter evolved during pyrolysis was substantially increased in the presence of hydrogen and especially when elevated hydrogen pressure was used.

Thermal conductivity of polymer composites with oriented boron nitride

International Nuclear Information System (INIS)

Ahn, Hong Jun; Eoh, Young Jun; Park, Sung Dae; Kim, Eung Soo

2014-01-01

Highlights: • Thermal conductivity depended on the orientation of BN in the polymer matrices. • Hexagonal boron nitride (BN) particles were treated by C 27 H 27 N 3 O 2 and C 14 H 6 O 8 . • Amphiphilic-agent-treated BN particles are more easily oriented in the composite. • BN/PVA composites with C 14 H 6 O 8 -treated BN showed the highest thermal conductivity. • Thermal conductivity of the composites was compared with several theoretical models. - Abstract: Thermal conductivity of boron nitride (BN) with polyvinyl alcohol (PVA) and/or polyvinyl butyral (PVB) was investigated as a function of the degree of BN orientation, the numbers of hydroxyl groups in the polymer matrices and the amphiphilic agents used. The composites with in-plane orientation of BN showed a higher thermal conductivity than the composites with out-of-plane orientation of BN due to the increase of thermal pathway. For a given BN content, the composites with in-plane orientation of BN/PVA showed higher thermal conductivity than the composites with in-plane orientation of BN/PVB. This result could be attributed to the improved degree of orientation of BN, caused by a larger number of hydroxyl groups being present. Those treated with C 14 H 6 O 8 amphiphilic agent demonstrated a higher thermal conductivity than those treated by C 27 H 27 N 3 O 2 . The measured thermal conductivity of the composites was compared with that predicted by the several theoretical models

Computer simulations of discharges from a lignite power plant complex

International Nuclear Information System (INIS)

Koukouliou, V.; Horyna, J.; Perez-Sanchez, D.

2008-01-01

This paper describes work carried out within the IAEA EMRAS program NORM working group to test the predictions of three computer models against measured radionuclide concentrations resulting from discharges from a lignite power plant complex. This complex consists of two power plants with a total of five discharge stacks, situated approximately 2-5 kilometres from a city of approximately 10,000 inhabitants. Monthly measurements of mean wind speed and direction, dust loading, and 238 U activities in fallout samples, as well as mean annual values of 232 Th activity in the nearest city sampling sites were available for the study. The models used in the study were Pc-CREAM (a detailed impact assessment model), and COMPLY and CROM (screening models). In applying the models to this scenario it was noted that the meteorological data provided was not ideal for testing, and that a number of assumptions had to be made, particularly for the simpler models. However, taking the gaps and uncertainties in the data into account, the model predictions from PC-CREAM were generally in good agreement with the measured data, and the results from different models were also generally consistent with each other. However, the COMPLY predictions were generally lower than those from PC-CREAM. This is of concern, as the aim of a screening model (COMPLY) is to provide conservative estimates of contaminant concentrations. Further investigation of this problem is required. The general implications of the results for further model development are discussed. (author)

Nuclear magnetic resonance studies of ancient buried wood-II. Observations on the origin of coal from lignite to bituminous coal

Science.gov (United States)

Hatcher, P.G.; Breger, I.A.; Szeverenyi, N.; Maciel, G.E.

1982-01-01

Coalified logs ranging in age from Late Pennsylvania to Miocene and in rank from lignite B to bituminous coal were analyzed by 13C nuclear magnetic resonance (NMR) utilizing the cross-polarization, magic-angle spinning technique, as well as by infrared spectroscopy. The results of this study indicate that at least three major stages of coalification can be observed as wood gradually undergoes transformation to bituminous coal. The first stage involves hydrolysis and loss of cellulose from wood with retention and differential concentration of the resistant lignin. The second stage involves conversion of the lignin residues directly to coalified wood of lignitic rank, during which the oxygen content of intermediate diagenetic products remains constant as the hydrogen content and the carbon content increases. These changes are thought to involve loss of methoxyl groups, water, and C3 side chains from the lignin. In the third major stage of coalification, the coalified wood increases in rank to subbituminous and bituminous coal; during this stage the oxygen content decreases, hydrogen remains constant, and the carbon content increases. These changes are thought to result from loss of soluble humic acids that are rich in oxygen and that are mobilized during compaction and dewatering. Relatively resistant resinous substances are differentially concentrated in the coal during this stage. The hypothesis that humic acids are formed as mobile by-products of the coalification of lignin and function only as vehicles for removal of oxygen represents a dramatic departure from commonly accepted views that they are relatively low-molecular-weight intermediates formed during the degradation of lignin that then condense to form high-molecular-weight coal structures. ?? 1982.

Weathering processes under various moisture conditions in a lignite mine spoil from As Pontes (N.W. Spain)

International Nuclear Information System (INIS)

Seoane, S.; Leiros, M.C.

1997-01-01

Processes contributing to acid release/consumption during weathering of a lignite mine spoil (2.3% w/w S as sulfides) from As Pontes (N.W. Spain) were studied under three moisture conditions (at field capacity or under alternate wetting-drying or forced percolation), which were simulated in laboratory experiments. Oxidation of sulfides to sulfates was favoured under all three moisture conditions, releasing most acid in spoil kept at field capacity. Hydroxysulfates formed in spoil kept at field capacity or under alternate wetting-drying conditions, thereby contributing to acid release. Acid consumption by dissolution of clay minerals, especially micas, was favoured under all three moisture conditions, but was particularly intense in spoil at field capacity. Dissolution of aluminium oxides was also favoured under all the moisture conditions studied. 27 refs., 8 figs., 6 tabs

Possible efficiency improvement by application of various operating regimes for the cooling water pump station at thermal power plant - Bitola

Directory of Open Access Journals (Sweden)

Mijakovski Vladimir

2012-01-01

Full Text Available Thermal power plant (TPP - Bitola is the largest electricity producer in the Republic of Macedonia with installed capacity of 691 MW. It is a lignite fired power plant, in operation since 1982. Most of the installed equipment is of Russian origin. Power plant's cold end comprised of a condenser, pump station and cooling tower is depicted in the article. Possible way to raise the efficiency of the cold end by changing the operating characteristics of the pumps is presented in the article. Diagramic and tabular presentation of the working characteristics of the pumps (two pumps working in paralel for one block with the pipeline, as well as engaged power for their operation are also presented in this article.

Thermal characteristics of thermobrachytherapy surface applicators for treating chest wall recurrence

International Nuclear Information System (INIS)

Arunachalam, K; Maccarini, P F; Craciunescu, O I; Stauffer, P R; Schlorff, J L

2010-01-01

The aim of this study was to investigate temperature and thermal dose distributions of thermobrachytherapy surface applicators (TBSAs) developed for concurrent or sequential high dose rate (HDR) brachytherapy and microwave hyperthermia treatment of chest wall recurrence and other superficial diseases. A steady-state thermodynamics model coupled with the fluid dynamics of a water bolus and electromagnetic radiation of the hyperthermia applicator is used to characterize the temperature distributions achievable with TBSAs in an elliptical phantom model of the human torso. Power deposited by 915 MHz conformal microwave array (CMA) applicators is used to assess the specific absorption rate (SAR) distributions of rectangular (500 cm 2 ) and L-shaped (875 cm 2 ) TBSAs. The SAR distribution in tissue and fluid flow distribution inside the dual-input dual-output (DIDO) water bolus are coupled to solve the steady-state temperature and thermal dose distributions of the rectangular TBSA (R-TBSA) for superficial tumor targets extending 10-15 mm beneath the skin surface. Thermal simulations are carried out for a range of bolus inlet temperature (T b = 38-43 deg. C), water flow rate (Q b = 2-4 L min -1 ) and tumor blood perfusion (ω b = 2-5 kg m -3 s -1 ) to characterize their influence on thermal dosimetry. Steady-state SAR patterns of the R- and L-TBSA demonstrate the ability to produce conformal and localized power deposition inside the tumor target sparing surrounding normal tissues and nearby critical organs. Acceptably low variation in tissue surface cooling and surface temperature homogeneity was observed for the new DIDO bolus at a 2 L min -1 water flow rate. Temperature depth profiles and thermal dose volume histograms indicate bolus inlet temperature (T b ) to be the most influential factor on thermal dosimetry. A 42 deg. C water bolus was observed to be the optimal choice for superficial tumors extending 10-15 mm from the surface even under significant blood perfusion

A real-time monitoring system for the assessment of stability and performance of in abandoned room and pillar lignite mines

International Nuclear Information System (INIS)

Aydan, O.; Tano, H.; Sakamoto, A.; Yamada, N.; Sugiura, K.

2005-01-01

The authors have been involved with the stability of abandoned mines beneath urbanized residential areas in Tokai region. These abandoned lignite mines were in operation until 1960's. There is a great concern about the stability of these abandoned mines during large earthquakes. The 2003 Miyagi Hokubu earthquake caused great damage to abandoned mines and resulted in collapses. The authors describe an integrated real-time monitoring system and they report some measured data up to now. The responses of monitoring system during a large roof collapse under gravitational condition as well as during and after two earthquakes are presented and their implications are discussed. (authors)

A real-time monitoring system for the assessment of stability and performance of in abandoned room and pillar lignite mines

Energy Technology Data Exchange (ETDEWEB)

Aydan, O. [Tokai Univ., Dept.of Marine Civil Engineering, Shizuoka (Japan); Tano, H. [Nihon Univ., Dept. of Civil Engineering, Koriyama (Japan); Sakamoto, A.; Yamada, N.; Sugiura, K. [Tobishima Construction Company, Nagoya Branch (Japan)

2005-07-01

The authors have been involved with the stability of abandoned mines beneath urbanized residential areas in Tokai region. These abandoned lignite mines were in operation until 1960's. There is a great concern about the stability of these abandoned mines during large earthquakes. The 2003 Miyagi Hokubu earthquake caused great damage to abandoned mines and resulted in collapses. The authors describe an integrated real-time monitoring system and they report some measured data up to now. The responses of monitoring system during a large roof collapse under gravitational condition as well as during and after two earthquakes are presented and their implications are discussed. (authors)

Differential sedimentation and selective flocculation in the desulfurization of Teruel lignite. Sedimentacion diferencial y floculacion selectiva en la desulfuracion de los lignitos de Teruel

Energy Technology Data Exchange (ETDEWEB)

Alvarez, R.; Clemente, C.; Gomez-Limon, D. (Escuela Tecnica Superior de Ingenieros de Minas de Madrid, Madrid (Spain))

1988-01-01

At the time of researching the possibility to remove the sulfur of the lignites located in the Teruel area via selective flocculation, it has been proved that in the case of the sulfur on its sulfur form, there's a pronounced interference with the differential sedimentation between coal and sulfur, increased by the fact of a selective liberation. This differential sedimentation shows better results on the sulfur removal process than that obtained by selective flocculation. 8 refs., 12 tabs.

From old lignite mining pits to new lakes. The example of rehabilitation of the former open-cast mining facilities at Berzdorf, Germany; Von alten Gruben zu neuen Seen am Beispiel des Tagebaues Berzdorf

Energy Technology Data Exchange (ETDEWEB)

Kolba, Manfred [LMBV mbH, Sanierungsbereich Lausitz, Senftenberg (Germany)

2009-09-15

The Lausitz and Central-German Mining Administration Company (LMBV) is project executor for the largest landscaping construction site in Europe. LMBV rehabilitates former open-cast mining facilities, as well as decommissioned coal-upgrading plants, to provide promising future areas for industrial complexes, and for landscapes that will attract a great number and variety of tourism developments. LMBV executes projects for the elimination of dangers as a result of the rising of groundwater to its former and natural level. In this context, the German Federal States involved in past and present lignite mining support extensive measures for enhancement of the standard of future use at the new lakes in Central Germany and in the Lausitz Region. This presentation shows the rehabilitation activities of LMBV as project executor in a great range of activities, by explaining the rehabilitation and transformation of the former lignite mining facilities in Berzdorf, Germany, in creation of the future Berzdorf Lake. (orig.)

Microbial activities in forest soils exposed to chronic depositions from a lignite power plant

Energy Technology Data Exchange (ETDEWEB)

Klose, S.; Wernecke, K.D.; Makeschin, F. [Technical University of Dresden, Tharandt (Germany)

2004-12-01

Atmospheric emissions of fly ash and SO{sub 2} from lignite-fired power plants strongly affect large forest areas in Germany. The impact of different deposition loads on the microbial biomass and enzyme activities was studied at three forest sites (Picea abies (L.) Karst.) along an emission gradient of 3, 6, and 15 km downwind of a coal-fired power plant, representing high, moderate and low emission rates. An additional site at a distance of 3 km from the power plant was chosen to study the influence of forest type on microbial parameters in coniferous forest soils under fly ash and SO{sub 2} emissions. Soil microbial biomass C and N, CO{sub 2} evolved and activities of L-asparaginase, L-glutaminase, beta-glucosidase, acid phosphatase and arylsulfatase (expressed on dry soil and organic C basis) were determined in the forest floor (L, Of and Oh horizon) and mineral top soil (0-10 cm). It is concluded that chronic fly ash depositions decrease litter decomposition by influencing specific microbial and enzymatic processes in forest soils.

Effect of some pre-treatments on the adsorption of methylene blue by Balkaya lignite

International Nuclear Information System (INIS)

Karaca, S.; Guerses, A.; Bayrak, R.

2004-01-01

In this study, the effects of some pre-treatments, such as HCl treatment, demineralization and pyrolysis, under a CO 2 atmosphere at different temperatures on the adsorption of methylene blue by Balkaya lignite were investigated. The adsorption capacities of the samples were determined before and after these pre-treatments. In addition, the removals of pyritic and organic sulfur and ash contents for the same coal samples were also defined. It was found that the adsorption capacities of the samples decreased after these pre-treatments. The decrease in adsorption capacity with pyrolysis can be attributed to the changes in surface morphology and/or pore size distribution of the coal samples. On the other hand, the observed decrease in adsorption capacity with removal of carbonates and silicates shows that these minerals have an important effect on methylene blue adsorption, and the adsorption considerably occurs through electrostatic interactions. In addition, the obtained results showed that the organic sulfur presence in the coal matrix have a positive effect on the methylene blue adsorption

Supplementary feeding with thermally treated cereals in common carp (Cyprinus carpio L.) pond farming and its effects on water quality, nutrient budget and zooplankton and zoobenthos assemblages

Czech Academy of Sciences Publication Activity Database

Hlaváč, D.; Anton-Pardo, M.; Másílko, J.; Hartman, P.; Regenda, J.; Vejsada, P.; Baxa, M.; Pechar, L.; Valentová, O.; Všetičková, Lucie; Drozd, B.; Adámek, Z.

2016-01-01

Roč. 24, č. 6 (2016), s. 1681-1697 ISSN 0967-6120 Institutional support: RVO:68081766 Keywords : Common carp * Nutrient budget * Supplementary feeding * Thermally treated cereals Subject RIV: EH - Ecology, Behaviour Impact factor: 1.095, year: 2016

Production of low ash coal by thermal extraction with N-methyl-2-pyrrolidinone

Energy Technology Data Exchange (ETDEWEB)

Do Kim, S.; Woo, K.J.; Jeong, S.K.; Rhim, Y.J.; Lee, S.H. [Korean Institute for Energy Research, Taejon (Republic of Korea). Clean Coal Technological Research Center

2008-07-15

Present study was conducted for the purpose of producing low ash coal from LRC (low rank coals) such as lignite and sub-bituminous coal through thermal extraction using polar solvent. Extraction from bituminous coal was also investigated for comparison. NMP as a polar solvent was used. The ratio of coal to solvent was adjusted as 1:10. Experimental conditions were established which include the extraction temperature of 200-430{sup o}C, initial applied pressure of 1-20 bar and extraction time of 0.5-2 hr were used. Extraction yield and ash content of extracted and residual coal were measured. The extraction yield increased with the increase of extraction temperature, and the ash content of extracted coal decreased below 0.4% at 400{sup o}C from the raw coal samples that have the ash contents of 4-6%. According to the analysis of experiments results, fixed carbon and calorific value increased, and H/C and O/C decreased.

Auxiliary mechanisms for work to dry stripping sections of the north Cheshskiy lignite basin of the CSSR

Energy Technology Data Exchange (ETDEWEB)

Jandek, J

1979-01-01

A brief examination is made of the employed methods for drying fields of lignite open pits: removal of water on water pumping channels, pumping out of water by mobile pump units, pumping out of water through wells (diameter 300 mm). Certain parameters of hydraulic excavators used for drying operations which are divided into three groups according to drive power are presented: 1) drive power over 100 kW (DN 101, aDN 103); 2 group drive power 50-100 kW (K 606, TMR 71, TEZM, Satur 051k, UDS 110a, UDS 113 and UDS 119 p, as well as the trench digger ER 7 am); third group drive power less than 50 kW (CASTOR 602, Poclain TY 45 and trench digger ETU 354). The expediency is indicated of unifying the hydraulic excavators based on the UDS 110 p excavator.

Synthetic-fuel production using Texas lignite and a very-high-temperature gas-cooled reactor for process heat and electrical power generation

International Nuclear Information System (INIS)

Ross, M.A.; Klein, D.E.

1981-05-01

This report presents two alternatives to increased reliance on foreign energy sources; each method utilizes the abundant domestic resources of coal, uranium, and thorium. Two approaches are studied in this report. First, the gasification and liquefaction of coal are accomplished with Lurgi gasifiers and Fischer-Tropsch synthesis. A 50,000 barrel per day facility, consuming 15 million tons of lignite coal per year, is used. Second, a nuclear-assisted coal conversion approach is studied using a very high temperature gas-cooled reactor with a modified Lurgi gasifier and Fischer-Tropsch synthesis. This is a preliminary report presenting background data and a means of comparison for the two approaches considered

Preliminary development of thermal nuclear cell homogenization code

International Nuclear Information System (INIS)

Su'ud, Z.; Shafii, M. A.; Yudha, S. P.; Waris, A.; Rijal, K.

2012-01-01

Nuclear fuel cell homogenization for thermal reactors usually include three main parts, i.e., fast energy resonance part which usually adopt narrow resonance approximation to treat the resonance, low (intermediate) energy region in which the resonance can not be treated accurately using NR approximation and therefore we should use intermediate resonance treatment, and thermal energy region (very low) in which the effect of thermal must be treated properly. In n this study the application of the intermediate resonance approximation treatment for low energy nuclear resonance is discussed. The method is iterative based. As a sample the method is applied in U-235 low lying resonance and the result is presented and discussed.

Flavor characterization of sugar-added pennywort (Centella asiatica L.) juices treated with ultra-high pressure and thermal processes.

Science.gov (United States)

Apichartsrangkoon, Arunee; Wongfhun, Pronprapa; Gordon, Michael H

2009-01-01

The flavor characteristics of pennywort juices with added sugar treated by ultra-high pressure, pasteurization, and sterilization were investigated using solid phase microextraction combined with gas chromatography-mass spectrometry. It was found that sesquiterpene hydrocarbons comprised the major class of volatile components present and the juices had a characteristic aroma due to the presence of volatiles including beta-caryophyllene and humulene and alpha-copaene. In comparison with heated juices, HPP-treated samples could retain more volatile compounds such as linalool and geraniol similar to those present in fresh juice, whereas some volatiles such as alpha-terpinene and ketone class were apparently formed by thermal treatment. All processing operations produced juice that was not significantly different in the concentration of total volatiles. Practical Application: Pennywort juice is considered a nutraceutical drink for health benefits. Therefore, to preserve all aroma and active components in this juice, a nonthermal process such as ultra-high pressure should be a more appropriate technique for retention of its nutritive values than pasteurization and sterilization.

The effect of some wood preservatives on the thermal degradation of Scots pine

International Nuclear Information System (INIS)

Tomak, Eylem D.; Baysal, Ergun; Peker, Huseyin

2012-01-01

Highlights: ► Scots pine samples were impregnated with 10 commercial wood preservatives. ► Thermal degradation of wood was evaluated by TG, DTG and DTA. ► The thermal behavior of treated wood differed from that of untreated wood. ► Boron containing wood preservatives yielded more charcoal than other preservatives. ► Boric oxide and metal compounds in the formulations may affect char weight. - Abstract: Wood has been a structural material for many years; however, its ability to burn has limited its use in some applications. This study aims to evaluate the effect of commercial wood preservatives having concentration of 4% on the thermal behavior of Scots pine wood, and compare the fire retardant effectiveness of these preservatives with that of boron compounds. Thermal degradation of treated and untreated wood samples was evaluated by thermogravimetry (TG), differential thermogravimetry (DTG) and differential thermal analysis (DTA). Thermal behavior of treated wood differed from thermal behavior of untreated wood in terms of a high char yield. Results showed that weight loss of wood reduced while char yield increased in the charring phase of the pyrolysis in the boron containing preservative treated wood accompanying with pyrolysis temperature lowered. The highest char yield was obtained from the samples treated with disodium octaborate tetrahydrate in the all treated groups.

Thermal shock effect on Mechanical and Physical properties of pre-moisture treated GRE composite

Science.gov (United States)

Chakraverty, A. P.; Panda, A. B.; Mohanty, U. K.; Mishra, S. C.; Biswal, B. B.

2018-03-01

Many practical situations may be encountered under which a GFRP (Glass fibre reinforced polymer) composite, during its service life, is exposed to the severities of sudden temperature fluctuations. Moisture absorption of GRE (Glass fibre reinforced epoxy) composites followed by various gradients of temperature fluctuations may cause thermo- mechanical degradation. It is on this context, the hand layed GRE composite samples are exposed to up-thermal shock (-40°C to +50°C) and down-thermal shock (+50°C to -40°C) for various time interval after several periods of moisture (hydrothermal/hygrothermal) conditioning. The thermally shocked GRE specimens are put to 3-point bend test to divulge inter laminar shear strength (ILSS). Least ILSS values are recorded for the samples with maximum period of moisture treatments under with both up-thermal and down-thermal shock conditions. Lower glass transition temperature (Tg) values, as revealed through the low temperature DSC test, are exhibited at maximum durations of both up-thermal and down-thermal shock for the samples with higher periods of hygrothermal/hydrothermal treatments. SEM fractographs of representative GRE specimens after optimum period of moisture treatments and thermal shock show the various modes of failures.

Techno-Environmental Assessment Of Co-Gasification Of Low-Grade Turkish Lignite With Biomass In A Trigeneration Power Plant

Directory of Open Access Journals (Sweden)

Amirabedin Ehsan

2014-12-01

Full Text Available Trigeneration or Combined Cooling, Heat and Power (CCHP which is based upon combined heat and power (CHP systems coupled to an absorption chiller can be recognized as one of the best technologies recovering biomass effectively to heat, cooling and power. Co-gasification of the lignite and biomass can provide the possibility for safe and effective disposal of different waste types as well as for sustainable and environmentally-friendly production of energy. In this article, a trigeneration system based on an IC engine and gasifier reactor has been simulated and realized using Thermoflex simulation software. Performance results suggest that utilization of sustainably-grown biomass in a Tri-Generation Power Plant (TGPP can be a possibility for providing cooling, heat and power demands with local renewable sources and reducing the environmental impacts of the energy conversion systems.

Pressure-assisted thermal sterilization of soup

Science.gov (United States)

Shibeshi, Kidane; Farid, Mohammed M.

2010-12-01

The overall efficiency of an existing scale-up pressure-assisted thermal sterilization (PATS) unit was investigated with regards to inactivation of Geobacillus stearothermophilus spores suspended in pumpkin soup. The PATS unit is a double pipe heat exchanger in which the soup is pumped into its inner high pressure tube and constrained by two high pressure valves, while steam is continuously passed through the annular region to heat the content. The technology is based on pressure generation by thermal expansion of the liquid in an enclosure. In this work, the addition of an air line to push the treated liquid food out of the existing PATS unit has improved the overall quality of the treated samples, as evidenced by achieving higher log reduction of the spores. Compared with thermal processing, the application of PATS shows the potential for lowering the thermal treatment temperature, offering improved food quality.

Investigation on the ignition, thermal acceleration and characteristic temperatures of coal char combustion

International Nuclear Information System (INIS)

Zhang, Bin; Fu, Peifang; Liu, Yang; Yue, Fang; Chen, Jing; Zhou, Huaichun; Zheng, Chuguang

2017-01-01

Highlights: • A new thermal model and measuring method for the ignition temperature are proposed. • Ignition occurs in a region but not a point with ambient conditions changing. • Ignition region is measured from the minimum to maximum ignition temperature. • T_i_g_,_m_a_x of coal char in TG-DSC is in line with the ignition temperature of EFR. - Abstract: Through using a new thermal analysis model and a method of coal/char combustion, the minimum ignition temperature and minimum ignition heat of three different ranks of pulverized coal char were measured by simultaneous Thermogravimetry and Differential Scanning Calorimetry (TG-DSC) experiments. The results show that the ignition of coal char occurs in the range between the minimum ignition temperature and the inflection-point temperature. The thermal acceleration and its gradient G_T increase with increasing heating rate and decrease with increasing coal char rank. The higher the G_T of the coal char, the more easily the ignition occurs and more rapidly the burning and burnout occur. The data show that the G_T of coal char of SLH lignite is 1.6 times more than that of coal char of ZCY bituminous and JWY anthracite in ignition zone, and 3.4 times in burning zone. The characteristic temperatures increase with increasing temperature of prepared char, heating rate and char rank. Moreover, the T_i_g_,_m_a_x calculated in DSC experiment is approximately in line with the ignition temperature obtained in the entrained flow reactor, which demonstrates the feasibility of the proposed theory.

The effect of some wood preservatives on the thermal degradation of Scots pine

Energy Technology Data Exchange (ETDEWEB)

Tomak, Eylem D., E-mail: eylemdizman@yahoo.com [Karadeniz Technical University, Faculty of Forestry, Forest Industrial Engineering Department, 61080 Trabzon (Turkey); Baysal, Ergun, E-mail: bergun@mu.edu.tr [Mugla University, Faculty of Technology, Department of Wood Science and Technology, Kotekli, 48000 Mugla (Turkey); Peker, Huseyin, E-mail: peker100@hotmail.com [Artvin Coruh University, Faculty of Forestry, Forest Industrial Engineering Department, 06100 Artvin (Turkey)

2012-11-10

Highlights: Black-Right-Pointing-Pointer Scots pine samples were impregnated with 10 commercial wood preservatives. Black-Right-Pointing-Pointer Thermal degradation of wood was evaluated by TG, DTG and DTA. Black-Right-Pointing-Pointer The thermal behavior of treated wood differed from that of untreated wood. Black-Right-Pointing-Pointer Boron containing wood preservatives yielded more charcoal than other preservatives. Black-Right-Pointing-Pointer Boric oxide and metal compounds in the formulations may affect char weight. - Abstract: Wood has been a structural material for many years; however, its ability to burn has limited its use in some applications. This study aims to evaluate the effect of commercial wood preservatives having concentration of 4% on the thermal behavior of Scots pine wood, and compare the fire retardant effectiveness of these preservatives with that of boron compounds. Thermal degradation of treated and untreated wood samples was evaluated by thermogravimetry (TG), differential thermogravimetry (DTG) and differential thermal analysis (DTA). Thermal behavior of treated wood differed from thermal behavior of untreated wood in terms of a high char yield. Results showed that weight loss of wood reduced while char yield increased in the charring phase of the pyrolysis in the boron containing preservative treated wood accompanying with pyrolysis temperature lowered. The highest char yield was obtained from the samples treated with disodium octaborate tetrahydrate in the all treated groups.

Aquatic balance in Vegoritis Lake, West Macedonia, Greece, relating to lignite mining works in the area

Science.gov (United States)

Dimitrakopoulos, D.; Grigorakou, E.; Koumantakis, J.

2003-04-01

Vegoritis Lake, which is located at Vegoritis closed Basin in West Macedonia, Greece, is the biggest lake in Greece. In 1994 the area of the lake was 35 Km2 with maximum depth 42 m at the northwestern part of the lake. It is the final receiving body of the surface runoff of the hydrological basin. Moreover, it is the surficial appearance of an enormous and not well-known karstic aquifer. Being a closed hydrological basin any interference in surface or groundwater conditions in every part of its area affects the level of the lake. The level of the lake in 1900 was 525 masl, in 1942 was 542 masl reaching the higher level of 543 masl in 1956. The increase of the level of the lake was due to the drainage of Ptolemais (Sarigiol) swamp through Soulou drain ditches that transfer the water in the lake. Since then, a continuous drawdown took place with small periods of rising of water level. Today, the level of the lake is declined in a smaller rate having reached the level of 510 masl. Water coming from the lake has been used in the past, and in some cases still does, for agricultural, industrial and domestic use, for hydropower generation and for the cooling system of power plants. Moreover, P.P.C. (Public Power Corporation of Greece) develops an intense activity in the area with the exploitation of the lignite deposits of the basin and power generation in several Power Plants. Few years ago significant quantities from Vegoritis Lake were used for hydro power of Agras Power Plant. With the elaboration of the existent data (water level measurements, recharge, discharge) the connection between the lowering of the surface of the lake and the subtracted quantities through the Arnissa Tunel the first years of its use, is obvious. The last twenty years the condition has change. Outflow through the Arnissa Tunnel for hydropower has stopped. The continued lowering of the level of the lake is caused, mainly, by overexploitation due to the intense increase of the irrigating land

Microscopic View of Defect Evolution in Thermal Treated AlGaInAs Quantum Well Revealed by Spatially Resolved Cathodoluminescence

Directory of Open Access Journals (Sweden)

Yue Song

2018-06-01

Full Text Available An aluminum gallium indium arsenic (AlGaInAs material system is indispensable as the active layer of diode lasers emitting at 1310 or 1550 nm, which are used in optical fiber communications. However, the course of the high-temperature instability of a quantum well structure, which is closely related to the diffusion of indium atoms, is still not clear due to the system’s complexity. The diffusion process of indium atoms was simulated by thermal treatment, and the changes in the optical and structural properties of an AlGaInAs quantum well are investigated in this paper. Compressive strained Al0.07Ga0.22In0.71As quantum wells were treated at 170 °C with different heat durations. A significant decrement of photoluminescence decay time was observed on the quantum well of a sample that was annealed after 4 h. The microscopic cathodoluminescent (CL spectra of these quantum wells were measured by scanning electron microscope-cathodoluminescence (SEM-CL. The thermal treatment effect on quantum wells was characterized via CL emission peak wavelength and energy density distribution, which were obtained by spatially resolved cathodoluminescence. The defect area was clearly observed in the Al0.07Ga0.22In0.71As quantum wells layer after thermal treatment. CL emissions from the defect core have higher emission energy than those from the defect-free regions. The defect core distribution, which was associated with indium segregation gradient distribution, showed asymmetric character.

Performance Enhancement of Silicon Alloy-Based Anodes Using Thermally Treated Poly(amide imide) as a Polymer Binder for High Performance Lithium-Ion Batteries.

Science.gov (United States)

Yang, Hwi Soo; Kim, Sang-Hyung; Kannan, Aravindaraj G; Kim, Seon Kyung; Park, Cheolho; Kim, Dong-Won

2016-04-05

The development of silicon-based anodes with high capacity and good cycling stability for next-generation lithium-ion batteries is a very challenging task due to the large volume changes in the electrodes during repeated cycling, which results in capacity fading. In this work, we synthesized silicon alloy as an active anode material, which was composed of silicon nanoparticles embedded in Cu-Al-Fe matrix phases. Poly(amide imide)s, (PAI)s, with different thermal treatments were used as polymer binders in the silicon alloy-based electrodes. A systematic study demonstrated that the thermal treatment of the silicon alloy electrodes at high temperature made the electrodes mechanically strong and remarkably enhanced the cycling stability compared to electrodes without thermal treatment. The silicon alloy electrode thermally treated at 400 °C initially delivered a discharge capacity of 1084 mAh g(-1) with good capacity retention and high Coulombic efficiency. This superior cycling performance was attributed to the strong adhesion of the PAI binder resulting from enhanced secondary interactions, which maintained good electrical contacts between the active materials, electronic conductors, and current collector during cycling. These findings are supported by results from X-ray photoelectron spectroscopy, scanning electron microscopy, and a surface and interfacial cutting analysis system.

MINE-NEC - A Game for the Analysis of Regional Water Policies in Open-Pit Lignite Mining Areas: An Improved Implementation for the NEC PC-8201A

OpenAIRE

Kaden, S.; Varis, O.

1986-01-01

The game MINE was developed for the analysis of regional water policies in open-pit lignite mining areas. It is implemented for a GDR test area. The purpose of the game is above all to teach decision makers and their staff in mining regions in order to get a better understanding of the complex interrelated socio-economic processes with respect t o water management in such regions. The game is designed to be played by five groups of players representing municipal and industrial water supply, a...

Thermally promoted addition of undecylenic acid on thermally hydrocarbonized porous silicon optical reflectors

OpenAIRE

Jalkanen, Tero; Mäkilä, Ermei; Sakka, Tetsuo; Salonen, Jarno; Ogata, Yukio H

2012-01-01

Thermally promoted addition of undecylenic acid is studied as a method for modifying porous silicon optical reflectors that have been pre-treated with thermal hydrocarbonization. Successful derivatization of undecylenic acid is demonstrated and confirmed with Fourier transform infrared and X-ray photoelectron spectroscopies. The results indicate that the hydrocarbonization pre-treatment considerably improves stability against oxidation and chemical dissolution in basic environments. The two-s...

Fe-catalyzed thermal conversion of sodium lignosulfonate to graphene

Science.gov (United States)

Sung Phil Mun; Zhiyong Cai; Jilei Zhang

2013-01-01

Sodium lignosulfonate (LS) from sulfite pulping processing was used as a carbon source to synthesize graphene. LS was mixed with Fe nanoparticles (FeNPs) as a catalyst and thermally treated at 1000 °C for 1 h. The Raman spectrum and X-ray diffraction pattern suggested that graphene sheets were formed in LS thermally treated with FeNPs (Fe-HTLS). Scanning...

Green synthesis of carbon quantum dots from lignite coal and the application in Fe3+ detection

Science.gov (United States)

Liu, Xuexia; Hao, Juanyuan; Liu, Jianhui; Tao, Hongcai

2018-02-01

Carbon quantum dots (CQDs) had attracted much attention due to their unique structures and excellent properties. Their green preparation was one of the research frontiers. However, most of the CQDs were prepared by strong acid oxidation, the way of which was not friendly to the environment. In this study, CQDs were prepared by green ozone oxidation of lignite coal, which is abundant and inexpensive. The CQDs were well dispersed, the size distribution of the obtained CQDs centralized from 2 to 4 nm with the average diameter of about 2.8 nm. In addition, the as-prepared CQDs containing rich oxygen functional groups exhibited good water-solubility and optical properties with yield reached 35%. The CQDs showed a highly sensitive and selective quenching effect to Fe3+ with desirable anti-interference performance. Moreover, the fluorescence intensity of CQDs had a good linear response to the Fe3+ concentration ranging from 10 to 150 µmol/L with the detection limit of 0.26 µmol/L. This green and facile synthesis method had the prospect of large-scale preparation of CQDs.

Restoration of open pit lignite mining in the former GDR: lessons to be learnt from Zwenkau

Energy Technology Data Exchange (ETDEWEB)

Wiegand, U.; Schreck, P.; Schreiter, P.; Lerche, I.; Glaesser, W. [Centre for Environmental Research Leipzig-Halle (UFZ), Halle (Germany) Dept. of Hydrogeology

2003-07-01

The interactions have been investigated between the near-surface sediments of the sediment dumping at the Zwenkau open pit near Leipzig, used for extraction of lignite, and the produced mining water. These environmental impacts are the legacy of the energy policy of the former GDR. The pyrite oxidation that takes place in the overburden sediments causes the formation of an oxidation front and the pH-value of sediments falls to about 2 to 3 very soon after deposition. The primary mineral contents are destroyed and a considerable number of elements are mobilized that remain locally in the sediment pores. Because of the very weak seepage, rainfall remains in the alluvial areas as so called dump lakes. The dump lakes are very acidic because the rainwater transport the mobilized elements from the surface. Autochthonous and allochthonous formations of secondary minerals have been observed and analysed. A continuously ongoing interaction of exogenous and endogenous effects hinders the hydrological and geochemical equilibrium stabilization. What to do with such a 'moonscape' is considered in the conclusions. 21 refs., 8 figs.

Colonization of spoil benches of an opencast lignite mine in northwest Spain by amphibians and reptiles

Energy Technology Data Exchange (ETDEWEB)

Galan, P. [University of Santiago de Compostela, Santiago de Compostela (Spain). Faculty of Biology

1997-02-01

This paper discusses the colonization by reptiles and amphibians of the spoil benches of the Meirama opencast lignite mine in northwest Spain over 10 years, following the start of the revegetation process. At Meirama, spoil benches are initially fertilized and hydroseeded with a pasture mix, but are subject to little subsequent management and are gradually colonized by scrub vegetation characteristic of the region. Herpetofauna censuses were carried out yearly on a single 2 ha plot over 6 years following hydroseeding, and in a single year on ten 2 ha plots which had been hydroseeded between 0 and 10 years previously. In addition, censuses were carried out on three undisturbed `control` plots close to the mine. Fifteen species (nine amphibians and six reptiles) were detected in one or more of the spoil-bench plots. Recolonization was particularly rapid after the first 2-3 years post-hydroseeding, and was closely related to habitat development due to revegetation and natural succession. Species composition was most similar to that in control plots in the oldest (ten-year-old) spoil plots.

Thermally Induced Magnetite-Haematite Transformation

International Nuclear Information System (INIS)

Mazo-Zuluaga, J.; Barrero, C. A.; Diaz-Teran, J.; Jerez, A.

2003-01-01

The products of thermal treatments of pure and copper doped magnetites have been investigated using Moessbauer spectrometry, XRD and thermal analysis techniques. The samples were heated in air between RT and 800 o C at several heating rates. Samples treated at 520 o C during 12 and 24 hours consist only of well-crystallized haematite. On the other hand, magnetites treated at 350 o C consisted of mixtures of haematite, maghemite and magnetite, with relative amount of each phase depending on the presence of copper as well as on the heating time. Results show that the transformation of magnetite to haematite goes through the formation of maghemite, and that the presence of copper delays this transformation.

Thermally Induced Magnetite-Haematite Transformation

Energy Technology Data Exchange (ETDEWEB)

Mazo-Zuluaga, J.; Barrero, C. A. [Universidad de Antioquia, Grupo de Estado Solido, Instituto de Fisica (Colombia); Diaz-Teran, J.; Jerez, A. [Universidad Nacional de Educacion a Distancia UNED, Po Senda del Rey 9, Departamento de Quimica Inorganica y Quimica Tecnica (Spain)

2003-06-15

The products of thermal treatments of pure and copper doped magnetites have been investigated using Moessbauer spectrometry, XRD and thermal analysis techniques. The samples were heated in air between RT and 800{sup o}C at several heating rates. Samples treated at 520{sup o}C during 12 and 24 hours consist only of well-crystallized haematite. On the other hand, magnetites treated at 350{sup o}C consisted of mixtures of haematite, maghemite and magnetite, with relative amount of each phase depending on the presence of copper as well as on the heating time. Results show that the transformation of magnetite to haematite goes through the formation of maghemite, and that the presence of copper delays this transformation.

Process of desulfurizing dephenolating, and cracking raw pitch obtained by dry distilling lignite, shale, etc

Energy Technology Data Exchange (ETDEWEB)

1932-12-21

A process is described of desulfurizing, dephenelating, and cracking the dry pitch obtained by dry distillation of lignite, bituminous shale, asphaltic rocks, and peat and fossil coals, that is characterized by the raw material being distilled in a retort together with calcium oxide, the vapors escaping from the still being compelled to pass through a catalyst tube containing calcium oxide mixed with other metallic oxide, the catalyst being helped by suitable heating to a temperature higher than that of the retort mentioned. For the purpose of lessening the quantity of phenolic groups contained in the raw tar to eliminate a great part of the sulfur belonging to the thiophenols and hydrogen sulfide without removing the organic radical to which they are attached, to accomplish a pyrogenic dissociation at the temperature of distillation of the pitch by means of using bone acid (phosphoric) to obtain a greater yield of light hydrocarbon from heavy hydrocarbons. Another purpose is the elimination of sulfur and thiophene and whatever neutral sulfur is contained in the primary pitch, by means of iron sulfate and copper in the anhydrous state or by means of other sulfates whose metals have the ability to form sulfides with sulfur.

Toxic emissions during co-combustion of biomass-waste wood-lignite blends in an industrial boiler.

Science.gov (United States)

Samaras, P; Skodras, G; Sakellaropoulos, G P; Blumenstock, M; Schramm, K W; Kettrup, A

2001-01-01

The objectives of this work were to study the PCDD/F emissions during the co-combustion of waste wood/coal co-combustion in an industrial boiler and to determine the relation of the toxic emissions to the fuel properties. Co-combustion experiments were performed in a 13.8 MWthermal industrial moving grate combustor. The fuels which were examined in this study included Greek lignite, natural uncontaminated wood, power poles and medium density fibers (MDFs) which were by-products of the plant production process. Fuel blends were prepared by mixing single components in various concentrations. PCDD/F emissions were collected during experimental runs and were analyzed according to standard methods. Low PCDD/F emissions were obtained during the co-combustion tests, lower than the limit value of 0.1 ng TEQ/Nm3. The lowest values were observed during the combustion of fuel blends containing MDF, possibly due to the inhibitory action of some of the N-containing MDF ingredients, such as urea. No direct correlation was found between the PCDD/F and the copper emissions, while examination of the PCDD/F homologue patterns revealed the predominance of the lower chlorinated isomers over the higher ones.

Bucket wheel rehabilitation of ERC 1400-30/7 high-capacity excavators from lignite quarries

Science.gov (United States)

Vîlceanu, Fl; Iancu, C.

2016-11-01

The existence of bucket wheel equipment type ERC 1400-30/7 in lignite quarries with lifetime expired, or in the ultimate life period, together with high cost investments for their replacement, makes rational the efforts made to rehabilitation in order to extend their life. Rehabilitation involves checking operational safety based on relevant expertise of metal structures supporting effective resistance but also the replacement (or modernization) of subassemblies that can increase excavation process productivity, lowering energy consumption, reducing mechanical stresses. This paper proposes an analysis of constructive solution of using a part of the classical bucket wheel, on which are located 9 cutting cups and 9 chargers cups and adding a new part so that the new redesigned bucket-wheel will contain 18 cutting-chargers cups, compared to the classical model. On the CAD model of bucket wheel was performed a static and a dynamic FEA, the results being compared with the yield strength of the material of the entire structure, were checked mechanical stresses in the overall distribution map, and were verified the first 4 vibrating modes the structure compared to real loads. Thus was verified that the redesigned bucket-wheel can accomplish the proposed goals respectively increase excavation process productivity, lowering energy consumption and reducing mechanical stresses.

Effect of heat treatment temperature on binder thermal conductivities

International Nuclear Information System (INIS)

Wagner, P.

1975-12-01

The effect of heat treatment on the thermal conductivities of a pitch and a polyfurfuryl alcohol binder residue was investigated. Graphites specially prepared with these two binders were used for the experiments. Measured thermal conductivities were treated in terms of a two-component system, and the binder thermal conductivities were calculated. Both binder residues showed increased thermal conductivity with increased heat treatment temperature

Experimental investigation into the surface oxidation of lignite high temperature coke

Energy Technology Data Exchange (ETDEWEB)

Schaefer, H G; Dallmann, W [Technische Hochschule Aachen (Germany, F.R.). Lehrgebiet Kokerei und Brikettierung

1979-11-01

It was intended to produce lignite high temperature coke (BHFK) in the laboratory comparable to that produced with the Salem-Lurgi-open hearth process and quench them according to the prescribed condition. By this means, the surface oxide formation could be continually recorded gravimetrically. The self-sustaining reaction of the physical and chemical adsorption on the loose material were observed under consideration that the adsorption or surface oxide can exist in a gaseous as well as in a liquid aggregate. The established steam isotherms and electron-microscope photos identified the product BFHK as a material which shows in the range of high-humidity capillary condensation. The continuous gravimetric adsorption leads to 1,9 per cent by weight on dry surface oxides. On the other hand, oxidized coke in the presence of water builds up on the surface to 2,3 per cent by weight. It became apparent that the finest capillary water is not involved in the formation of the oxide. For the dry accumulation, which is a reaction of the first degree, the equation for the accumulation of the oxygen is given. From the BET surface, made up from the graphite-like ring structure of the carbon surface, as well as the dposited quantity of oxide, the surface density of the oxygen atoms is indicated in relation to the quantity of carbon atoms, or alternatively the six-ring. The dry deposition leads to a proportion of 1,5 oxygen atoms to 10 carbon atoms. In a wet reaction, the ratio is 1,8 to 10. With increasing quantities of oxide, the content of volatile matter, the sparking point and reactivity increase, while the porosity diminishes as a consequence.

Improving thermal stability and efficacy of BCNU in treating glioma cells using PAA-functionalized graphene oxide

Directory of Open Access Journals (Sweden)

Lu YJ

2012-03-01

Full Text Available Yu-Jen Lu1,2,#, Hung-Wei Yang1,#, Sheng-Che Hung3, Chiung-Yin Huang2, Shin-Ming Li4, Chen-Chi M Ma4, Pin-Yuan Chen2, Hong-Chieh Tsai2, Kuo-Chen Wei2, Jyh-Ping Chen1 1Department of Chemical and Materials Engineering, Chang Gung University, Kwei-San, Taoyuan, Taiwan; 2Department of Neurosurgery, Chang Gung Memorial Hospital, Kwei-San, Taoyuan, Taiwan; 3Department of Radiology, Taipei Veterans General Hospital, Taipei, Taiwan; 4Department of Chemical Engineering, National Tsing Hua University, Hsinchu, Taiwan#These authors contributed equally to this workBackground: 1,3-bis(2-chloroethyl-1-nitrosourea (BCNU, a commercial chemotherapeutic drug for treating malignant brain tumors, has poor thermal stability and a short half-life. Immobilization of BCNU on a nanocarrier might increase the thermal stability of BCNU and extend its half-life.Methods: Nanosized graphene oxide (GO could be modified by polyacrylic acid (PAA to improve the aqueous solubility and increase the cell penetration efficacy of the nanocarrier. PAA–GO intended as a drug carrier for BCNU was prepared and characterized in this study. The size and thickness of PAA–GO was investigated by transmission electron microscopy and atomic force microscopy, and the presence of PAA functional groups was confirmed by electron spectroscopy for chemical analysis and thermogravimetric analysis. BCNU was conjugated to PAA–GO by covalent binding for specific killing of cancer cells, which could also enhance the thermal stability of the drug.Results: Single layer PAA–GO (about 1.9 nm with a lateral width as small as 36 nm was successfully prepared. The optimum drug immobilization condition was by reacting 0.5 mg PAA–GO with 0.4 mg BCNU, and the drug-loading capacity and residual drug activity were 198 µg BCNU/mg PAA–GO and 70%, respectively. This nanocarrier significantly prolonged the half-life of bound BCNU from 19 to 43 hours compared with free drug and showed efficient intracellular

Imposed Thermal Fatigue and Post-Thermal-Cycle Wear Resistance of Biomimetic Gray Cast Iron by Laser Treatment

Science.gov (United States)

Sui, Qi; Zhou, Hong; Zhang, Deping; Chen, Zhikai; Zhang, Peng

2017-08-01

The present study aims to create coupling biomimetic units on gray cast iron substrate by laser surface treatment (LST). LSTs for single-step (LST1) and two-step (LST2) processes, were carried out on gray cast iron in different media (air and water). Their effects on microstructure, thermal fatigue, and post-thermal-cycle wear (PTW) resistance on the specimens were studied. The tests were carried out to examine the influence of crack-resistance behavior as well as the biomimetic surface on its post-thermal-cycle wear behavior and different units, with different laser treatments for comparison. Results showed that LST2 enhanced the PTW behaviors of gray cast iron, which then led to an increase in its crack resistance. Among the treated cast irons, the one treated by LST2 in air showed the lowest residual stress, due to the positive effect of the lower steepness of the thermal gradient. Moreover, the same specimen showed the best PTW performance, due to its superior crack resistance and higher hardness as a result of it.

Temperature dependent capacity contribution of thermally treated anode current collectors in lithium ion batteries

International Nuclear Information System (INIS)

Kim, Tae Kwon; Li Xifei; Wang Chunlei

2013-01-01

Highlights: ► We studied the influence of the thermal treatment of current collectors on the energy capacity. ► Different current collectors show different thermal treatment effect on performance. ► The non-negligible capacity contribution is closely related to the treatment temperatures. ► Our results could be beneficial to designing battery architectures. - Abstract: Metal current collectors, offering a good connection between the active materials and the external circuit, is an important component in a rechargeable lithium ion battery. Some necessary thermal treatment in the battery fabrication and assembly procedure results in current collectors with some non-negligible reversible energy capacities; however, these energy capacities were negligible in the previous references. In this research, for the first time, we investigated the influence of the thermal treatment of current collectors (such as copper foil and stainless steel disk) on energy capacities. Our results indicate that different current collector materials have different thermal treatment effects on their electrochemical performance. The non-negligible capacity contribution is closely related to the treatment temperature.

Overview of thermal conductivity models of anisotropic thermal insulation materials

Science.gov (United States)

Skurikhin, A. V.; Kostanovsky, A. V.

2017-11-01

Currently, the most of existing materials and substances under elaboration are anisotropic. It makes certain difficulties in the study of heat transfer process. Thermal conductivity of the materials can be characterized by tensor of the second order. Also, the parallelism between the temperature gradient vector and the density of heat flow vector is violated in anisotropic thermal insulation materials (TIM). One of the most famous TIM is a family of integrated thermal insulation refractory material («ITIRM»). The main component ensuring its properties is the «inflated» vermiculite. Natural mineral vermiculite is ground into powder state, fired by gas burner for dehydration, and its precipitate is then compressed. The key feature of thus treated batch of vermiculite is a package structure. The properties of the material lead to a slow heating of manufactured products due to low absorption and high radiation reflection. The maximum of reflection function is referred to infrared spectral region. A review of current models of heat propagation in anisotropic thermal insulation materials is carried out, as well as analysis of their thermal and optical properties. A theoretical model, which allows to determine the heat conductivity «ITIRM», can be useful in the study of thermal characteristics such as specific heat capacity, temperature conductivity, and others. Materials as «ITIRM» can be used in the metallurgy industry, thermal energy and nuclear power-engineering.

Adsorption of lignite-derived humic acids on coal-based mesoporous activated carbons.

Science.gov (United States)

Lorenc-Grabowska, Ewa; Gryglewicz, Grazyna

2005-04-15

The adsorption by a coal-based mesoporous activated carbon of humic acids (HAs) isolated from two Polish lignites was studied. For comparison, a commercial Aldrich humic acid was also included into this study. The differences in chemical structure and functional groups of HAs were determined by elemental analysis and infrared spectroscopy DRIFT. Two activated carbons used differed in terms of mesopore volume, mesopore size distribution, and chemical properties of the surface. The kinetics of adsorption of HAs have been discussed using three kinetic models, i.e., the first-order Lagergren model, the pseudo-second-order model, and the intraparticle diffusion model. It was found that the adsorption of HAs from alkaline solution on mesoporous activated carbon proceeds according to the pseudo-second-order model. The correlation coefficients were close to 1. The intraparticle diffusion of HA molecules within the carbon particle was identified to be the rate-limiting step. Comparing the two activated carbons, the carbon with a higher volume of pores with widths of 10-50 nm showed a greater removal efficiency of HA. An increase in the Freundlich adsorption capacity with decreasing carbon content of HA was observed. Among the HAs studied, S-HA shows characteristics indicating the highest contribution of small-size fraction. The S-HA was removed by both activated carbons to the highest extent. The effect of pH solution on the adsorption of HA was examined over the range pH 5.4-12.2. It was found that the extent of adsorption decreased with decreasing pH of the solution.

Preparation of sewage sludges for the thermal disposal in lignite power stations. Aufbereitung von Klaerschlaemmen zur thermischen Entsorgung in Braunkohlenkraftwerken

Energy Technology Data Exchange (ETDEWEB)

Krone, C.; Koch, J.; Leidel, H.; Scheel, W. (VEAG Vereinigte Energiewerke AG, Ingenieurunternehmen fuer Kraftwerks-, Energie- und Umwelttechnik, Vetschau (Germany))

1992-10-01

The thermal disposal of communal sewage sludges as well as the additional combustion of such substances in furnaces of power station boilers are really no technical solutions. New are the consideration concerning the sludge preparation with the aid of the steam fluidized bed drying process and the additional combustion of the dried products in raw-brown-coal-fired large-scale steam generators. - The investigation proves the technical feasibility and points to problems which still have to be tackled. (orig.).

Technical viability of nitric leaching in the desulphurisation of lignite from the Teruel region. La lixiviacion nitrica como posibilidad tecnica en la desulfuracion de los lignitos de Teruel

Energy Technology Data Exchange (ETDEWEB)

Alvarez, R.; Clemente, C.; Gomez-Limon, D. (Esc. Tec. Sup. Ing. Min., Madrid (Spain))

1989-11-01

Studies of selective flocculation and sedimentation of Teruel lignite which is high in both pyritic and organic sulphur enabled the sulphur content to be reduced to just 4.25%. Tests have subsequently been carried out with nitric leaching and the sulphur content has been reduced to below the levels of organic sulphur in addition to reducing the ash content by 4 to 9%. The cost of the reagents was similar or lower than in other processes and practically all the coal was recovered. 11 refs., 1 fig., 4 tabs.

Restoration of the water balance in the lignite mining areas of central Germany and Lusatia; Sanierung des Wasserhaushalts in den Braunkohlenbergbaugebieten Mitteldeutschlands und der Lausitz

Energy Technology Data Exchange (ETDEWEB)

Benthaus, Friedrich-Carl [Lausitzer und Mitteldeutsche Bergbau-Verwaltungsgesellschaft mbH (LMBV), Senftenberg (Germany). Ingenieurbereich Sanierung, Strategie und Entwicklung; Scholz, Eckhard [Lausitzer und Mitteldeutsche Bergbau-Verwaltungsgesellschaft mbH (LMBV), Senftenberg (Germany). Ingenieurbereich Sanierung; Uhlig, Christiane [Lausitzer und Mitteldeutsche Bergbau-Verwaltungsgesellschaft mbH (LMBV), Senftenberg (Germany). Ingenieurbereich Sanierung, Geotechnik Mitteldeutschland; Heine, Rudi [Lausitzer und Mitteldeutsche Bergbau-Verwaltungsgesellschaft mbH (LMBV), Senftenberg (Germany). Ingenieurbereich Sanierung, Planung Wasserbau Lausitz; Totsche, Oliver [Lausitzer und Mitteldeutsche Bergbau-Verwaltungsgesellschaft mbH (LMBV), Senftenberg (Germany). Ingenieurbereich Sanierung, Geotechnik Lausitz

2010-10-15

The lignite mining industry in central Germany and Lusatia has interfered with the water balance in the regions by long-standing lowering of the ground water and changing of the surface waters. The restoration is aimed at re-establishment of a largely self-regulating water balance by flooding and aftercare. The planning of the linkage of the 220 lakes in the aftermath of the mining industry to the public waterway network should be based on the conditions prevailing after abandonment of the mining industry. Innovative geochemical and biological processes are being further developed to improve the water quality, which is characterised by oxidation of the iron sulphides. (orig.)

Influence of nano-AlN particles on thermal conductivity, thermal stability and cure behavior of cycloaliphatic epoxy/trimethacrylate system

Directory of Open Access Journals (Sweden)

2011-02-01

Full Text Available We have prepared a series of nano-sized aluminium nitride (nano-AlN/cycloaliphatic epoxy/trimethacrylate (TMPTMA systems and investigated their morphology, thermal conductivity, thermal stability and curing behavior. Experimental results show that the thermal conductivity of composites increases with the nano-AlN filler content, the maximum value is up to 0.47 W/(m.K. Incorporation of a small amount of the nano-AlN filler into the epoxy/TMPTMA system improves the thermal stability. For instance, the thermal degradation temperature at 5% weight loss of nano-AlN/epoxy/TMPTMA system with only 1 wt% nano-AlN was improved by ~8ºC over the neat epoxy/TMPTMA system. The effect of nano-AlN particles on the cure behavior of epoxy/TMPTMA systems was studied by dynamic differential scanning calorimetry. The results showed that the addition of silane treated nano-AlN particles does not change the curing reaction mechanism and silane treated nano-AlN particles could bring positive effect on the processing of composite since it needs shorter pre-cure time and lower pre-temperature, meanwhile the increase of glass transition temperature of the nanocomposite improves the heat resistance.

{sup 99}Mo sorption by thermally treated hydrotalcites

Energy Technology Data Exchange (ETDEWEB)

Serrano, J.; Bertin, V.; Bulbulian, S.

2000-04-04

MoO{sub 4}{sup {minus}2} ions were sorbed in calcined hydrotalcite contained in a column. It was found that 98% of {sup 99m}Tc formed by {sup 99}Mo decay was eluted through the column in the form of pertechnetate. The content of radionuclides was determined by {gamma}-spectrometry, and natural molybdenum was measured by neutron activation analysis. Solids were characterized by thermal analysis, X-ray diffraction, and infrared spectroscopy. Through batch experiments, the hydrotalcite capacity toward molybdate ions (1.12 x 10{sup {minus}3} M) was found to be 3.2 mequiv g{sup {minus}1}. It was found that the high molybdate adsorbing capacity of calcined hydrotalcite could be utilized in designing a {sup 99m}Tc generator made with low specific activity {sup 99}Mo-molybdate samples.

Thermodynamic analyses of solar thermal gasification of coal for hybrid solar-fossil power and fuel production

International Nuclear Information System (INIS)

Ng, Yi Cheng; Lipiński, Wojciech

2012-01-01

Thermodynamic analyses are performed for solar thermal steam and dry gasification of coal. The selected types of coal are anthracite, bituminous, lignite and peat. Two model conversion paths are considered for each combination of the gasifying agent and the coal type: production of the synthesis gas with its subsequent use in a combined cycle power plant to generate power, and production of the synthesis gas with its subsequent use to produce gasoline via the Fischer–Tropsch synthesis. Replacement of a coal-fired 35% efficient Rankine cycle power plant and a combustion-based integrated gasification combined cycle power plant by a solar-based integrated gasification combined cycle power plant leads to the reduction in specific carbon dioxide emissions by at least 47% and 27%, respectively. Replacement of a conventional gasoline production process via coal gasification and a subsequent Fischer–Tropsch synthesis with gasoline production via solar thermal coal gasification with a subsequent Fischer–Tropsch synthesis leads to the reduction in specific carbon dioxide emissions by at least 39%. -- Highlights: ► Thermodynamic analyses for steam and dry gasification of coal are presented. ► Hybrid solar-fossil paths to power and fuels are compared to those using only combustion. ► Hybrid power production can reduce specific CO 2 emissions by more than 27%. ► Hybrid fuel production can reduce specific CO 2 emissions by more than 39%.

Concentrations and source apportionment of PM10 and associated elemental and ionic species in a lignite-burning power generation area of southern Greece.

Science.gov (United States)

Argyropoulos, G; Grigoratos, Th; Voutsinas, M; Samara, C

2013-10-01

Ambient concentrations of PM10 and associated elemental and ionic species were measured over the cold and the warm months of 2010 at an urban and two rural sites located in the lignite-fired power generation area of Megalopolis in Peloponnese, southern Greece. The PM10 concentrations at the urban site (44.2 ± 33.6 μg m(-3)) were significantly higher than those at the rural sites (23.7 ± 20.4 and 22.7 ± 26.9 μg m(-3)). Source apportionment of PM10 and associated components was accomplished by an advanced computational procedure, the robotic chemical mass balance model (RCMB), using chemical profiles for a variety of local fugitive dust sources (power plant fly ash, flue gas desulfurization wet ash, feeding lignite, infertile material from the opencast mines, paved and unpaved road dusts, soil), which were resuspended and sampled through a PM10 inlet onto filters and then chemically analyzed, as well as of other common sources such as vehicular traffic, residential oil combustion, biomass burning, uncontrolled waste burning, marine aerosol, and secondary aerosol formation. Geological dusts (road/soil dust) were found to be major PM10 contributors in both the cold and warm periods of the year, with average annual contribution of 32.6 % at the urban site vs. 22.0 and 29.0 % at the rural sites. Secondary aerosol also appeared to be a significant source, contributing 22.1 % at the urban site in comparison to 30.6 and 28.7 % at the rural sites. At all sites, the contribution of biomass burning was most significant in winter (28.2 % at the urban site vs. 14.6 and 24.6 % at the rural sites), whereas vehicular exhaust contribution appeared to be important mostly in the summer (21.9 % at the urban site vs. 11.5 and 10.5 % at the rural sites). The highest contribution of fly ash (33.2 %) was found at the rural site located to the north of the power plants during wintertime, when winds are favorable. In the warm period, the highest contribution of fly ash was found at the

Preliminary laboratory investigation of thermally treated recycled concrete aggregate for general use in concrete

NARCIS (Netherlands)

Larbi, J.A.; Heijnen, W.M.M.; Brouwer, J.P.; Mulder, E.

2000-01-01

This paper deals with a preliminary laboratory study to assess the effectiveness of thermal treatment methods to improve the quality of recycled concrete aggregate. The samples used for the study consisted of sieved fractions of crushed concrete that were subjected to various thermal treatments at

Applying an overall criterion according to the European norms, for ecological assessment of the thermal electrical power plant operation

International Nuclear Information System (INIS)

Cardu, Mircea; Petrescu, Camelia

2006-01-01

This work consists of assessing the thermal power plants impact on the environment by the global considering of the pollutant SO 2 and NO x emissions. This assessment takes into account the emission comparisons with the admissible values provided by the European norms. The conclusion we might draw is that the SN proposed global criterion application, (S from sulfur, namely the sulfur dioxide and N from nitrogen, namely the nitrogen oxides), the investment expenses for installing the necessary SDN and SDS systems (were SDN stands for denox plant and SDS for desulfurization systems), and the operation expenses are smaller (in case of pit coal they are even smaller) if we apply such criterion. The ecologic analysis model we applied as an estimation for large solid fuels categories (lignite, pit coal) and for the 330 MW existing power units, can also be applied to the actual cases for different fuel qualities or unit unitary power levels

Comparison of health and environmental effects of nuclear power plants and lignite-burning power plants

International Nuclear Information System (INIS)

Horacek, P.; Chytil, I.; Razga, J.

1988-01-01

The individual factors are discussed which characterize the impact of nuclear power plants and lignite-burning power plants on human health and on the environment. The study proceeds from the IAEA categorization of these impacts. In this light, attention is centred on the impact of the normal operation of power plants and on accidents. The former category is further divided into regional impacts such as the emission of chemical substances, the emission of radioactive substances, heat emissions and the sum of regional factors, and on global impacts such as emissions of carbon dioxide, emissions of long-lived radionuclides and the sum of global impacts. It is stated that research should pay more attention to the dangers of the effects of such a state of affairs when the infrastructure contaminated after a large-scale accident would be put out of operation, and the dangers of such a situation especially in small countries with great population densities. Such accidents represent the biggest danger of the use of nuclear power. The greatest danger of coal-burning power plants is their global impact on the atmosphere caused by the increasing concentration of carbon dioxide from burning fossil fuels. (Z.M.). 4 figs., 13 refs

Methodology for quantifying uncertainty in coal assessments with an application to a Texas lignite deposit

Energy Technology Data Exchange (ETDEWEB)

Olea, Ricardo A.; Luppens, James A.; Tewalt, Susan J. [U.S. Geological Survey, Reston, VA (United States)

2011-01-01

A common practice for characterizing uncertainty in coal resource assessments has been the itemization of tonnage at the mining unit level and the classification of such units according to distance to drilling holes. Distance criteria, such as those used in U.S. Geological Survey Circular 891, are still widely used for public disclosure. A major deficiency of distance methods is that they do not provide a quantitative measure of uncertainty. Additionally, relying on distance between data points alone does not take into consideration other factors known to have an influence on uncertainty, such as spatial correlation, type of probability distribution followed by the data, geological discontinuities, and boundary of the deposit. Several geostatistical methods have been combined to formulate a quantitative characterization for appraising uncertainty. Drill hole datasets ranging from widespread exploration drilling to detailed development drilling from a lignite deposit in Texas were used to illustrate the modeling. The results show that distance to the nearest drill hole is almost completely unrelated to uncertainty, which confirms the inadequacy of characterizing uncertainty based solely on a simple classification of resources by distance classes. The more complex statistical methods used in this study quantify uncertainty and show good agreement between confidence intervals in the uncertainty predictions and data from additional drilling. (author)

Methodology for quantifying uncertainty in coal assessments with an application to a Texas lignite deposit

Science.gov (United States)

Olea, R.A.; Luppens, J.A.; Tewalt, S.J.

2011-01-01

A common practice for characterizing uncertainty in coal resource assessments has been the itemization of tonnage at the mining unit level and the classification of such units according to distance to drilling holes. Distance criteria, such as those used in U.S. Geological Survey Circular 891, are still widely used for public disclosure. A major deficiency of distance methods is that they do not provide a quantitative measure of uncertainty. Additionally, relying on distance between data points alone does not take into consideration other factors known to have an influence on uncertainty, such as spatial correlation, type of probability distribution followed by the data, geological discontinuities, and boundary of the deposit. Several geostatistical methods have been combined to formulate a quantitative characterization for appraising uncertainty. Drill hole datasets ranging from widespread exploration drilling to detailed development drilling from a lignite deposit in Texas were used to illustrate the modeling. The results show that distance to the nearest drill hole is almost completely unrelated to uncertainty, which confirms the inadequacy of characterizing uncertainty based solely on a simple classification of resources by distance classes. The more complex statistical methods used in this study quantify uncertainty and show good agreement between confidence intervals in the uncertainty predictions and data from additional drilling. ?? 2010.

Treating carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

Kelly, T D

1927-07-29

Coal, lignite, shale, peat, or like carbonaceous material is heated at 70 to 300/sup 0/C with an alkaline solution of sodium, potassium, or ammonium oleate and aluminum sulfate is added in order to solidify the oleate. The solid material is separated and molded or shaped or disintegrated for use as a pigment or mixed with rubber or similar compounds such as solidified, oxidized or polymerized oils in making building blocks or tiles, tires, footwear, or other resilient material. It may be distilled with water or steam in a retort to make gas, or in porous condition can be burnt. The liquid products may be subjected to fractional distillation or mixed with bitumen, resin or oils or materials such as clay, red oxide, or barytes to give colour or body in the manufacture of waterproof heatproof dressings which may be made quick-drying by the addition of ammonia, or for mixing with or spreading over stones or on roads or concrete.

The genesis of the Nissi peatland (northwestern Greece) as an example of peat and lignite deposit formation in Greece

Energy Technology Data Exchange (ETDEWEB)

Christianis, K. (University of Patras, Patras (Greece). Dept of Geology)

1994-07-01

The Nissi Fen is located in a 12 km[sup 2] intramontane basin in northwestern Greece. Since the last glacial, limnotelmatic and pure telmatic conditions, controlled mainly by karstic springs and partly by surface waters, favoured peat formation in the basin, resulting in the accumulation of a peat deposit up to 15 m thick. The present fen occupies a large area of almost 9 km[sup 2]. Flora cover comprises mainly Cyperaceae ([ital Cladium mariscus] and [ital Carex] species), while [ital Phragmites australis] extend along the banks of a river flowing through the basin, as well as around a lake in the southern part of the fen. These species also contributed to the peat formation. The Nissi peatland shows many genetic similarities to the Philippi peat deposit, Eastern Macedonia, and may be considered as a recent analogue to the lignite deposits in the basins of Ptolemais, Western Macedonia and Megalopolis, the Peloponnese. 36 refs., 5 figs.

A comparative study of the physical properties of Sb2S3 thin films treated with N2 AC plasma and thermal annealing in N2

International Nuclear Information System (INIS)

Calixto-Rodriguez, M.; Martinez, H.; Pena, Y.; Flores, O.; Esparza-Ponce, H.E.; Sanchez-Juarez, A.; Campos-Alvarez, J.; Reyes, P.

2010-01-01

As-deposited antimony sulfide thin films prepared by chemical bath deposition were treated with nitrogen AC plasma and thermal annealing in nitrogen atmosphere. The as-deposited, plasma treated, and thermally annealed antimony sulfide thin films have been characterized by X-ray diffraction (XRD), energy dispersive X-ray spectroscopy, scanning electron microscopy, atomic force microscopy, UV-vis spectroscopy, and electrical measurements. The results have shown that post-deposition treatments modify the crystalline structure, the morphology, and the optoelectronic properties of Sb 2 S 3 thin films. X-ray diffraction studies showed that the crystallinity of the films was improved in both cases. Atomic force microscopy studies showed that the change in the film morphology depends on the post-deposition treatment used. Optical emission spectroscopy (OES) analysis revealed the plasma etching on the surface of the film, this fact was corroborated by the energy dispersive X-ray spectroscopy analysis. The optical band gap of the films (E g ) decreased after post-deposition treatments (from 2.36 to 1.75 eV) due to the improvement in the grain sizes. The electrical resistivity of the Sb 2 S 3 thin films decreased from 10 8 to 10 6 Ω-cm after plasma treatments.

Thermal expansion anomaly and thermal conductivity of U3O8

International Nuclear Information System (INIS)

Schulz, B.

1975-01-01

The anomaly in the thermal expansion of U 3 O 8 and results of the thermal conductivity of this compound are described. U 3 O 8 powder heat treated at 1,223 K was consolidated by pressing and sintering in air at 1,223 and 1,373 K to a density of 66% and 80.8% TD. The O/U ratio was 2.67 and 2.63 respectively, the crystal structure being orthorhombic in both cases. For UOsub(2.63) the thermal linear expansion was measured in the temperature range 293 K-1,063 K in pressing direction and normal to it, while for UOsub(2.67) measurements were done parallel to the pressing direction. The curves of the linear thermal expansion from 373 K up to 623 K show negative values and above positive for the three curves. The results are related to known data of phase-transition-temperatures of the orthorhombic U 3 O 8 . Measurements of the thermal conductivity were done on UOsub(2.67). Because of the high porosity of the samples, known relationships for the porosity correction of the thermal conductivity were proved on alumina with 34 % porosity. The values of the thermal conductivity of UOsub(2.67) (corrected to zero porosity) show a very slight temperature dependence, they are about three times lower than those of the stoichiometric uranium dioxide in the same temperature range

Study on thermal conductive BN/novolac resin composites

International Nuclear Information System (INIS)

Li, Shasha; Qi, Shuhua; Liu, Nailiang; Cao, Peng

2011-01-01

Highlights: → Boron nitride (BN) particles were used to modify novolac resin. → BN particles were pretreated by γ-aminopropyltriethoxysilane. → The thermal conductivity trend of composite almost agrees with the predicted data from the Maxwell-Eucken model. → At BN concentration of 80 wt.%, thermal conductivity value of composite is 4.5 times that of pure novolac resin. → Combined use of the larger and smaller particles with a mass ratio of 1:2 provides the composites with the maximum thermal conductivity among the testing systems. → The composite thermal property also increases with an increase in the BN concentration. - Abstract: In this study, γ-aminopropyltriethoxysilane-treated boron nitride (BN) particles were used to modify novolac resin. The effect of varying the BN concentration, particle size, and hybrid BN fillers with the binary particle size distribution on the thermal conductivity of the composites was investigated. Scanning electron microscopy (SEM) imaging showed homogeneously dispersed treated BN particles in the matrix. Furthermore, the thermal conductivity increased as the BN concentration was increased. This behavior was also observed when the filler size was increased. Experimentally obtained thermal conductivity values agree with the predicted data from the Maxwell-Eucken model well at less than 70 wt.% BN loading. A larger particle size BN-filled novolac resin exhibits a higher thermal conductivity than a smaller particle size BN-filled one. The combined use of 0.5 and 15 μm particles with a mass ratio of 2:1 achieved the maximum thermal conductivity among the testing systems. The thermal resistance properties of the composites were also studied.

Revisiting the effects of organic solvents on the thermal reduction of graphite oxide

International Nuclear Information System (INIS)

Barroso-Bujans, Fabienne; Fierro, José Luis G.; Alegría, Angel; Colmenero, Juan

2011-01-01

Highlights: ► Retention of organic solvent on graphite oxide interlayer space. ► Decreasing exfoliation temperature. ► Close link between structure and thermal behavior of solvent treated graphite oxide. ► Restacking inhibition of thermally reduced graphite oxide sheets. ► Changes in kinetic mechanisms of thermal reduction. - Abstract: Treatment of graphite oxide (GO) with organic solvents via sorption from either liquid or gas phase, and subsequent desorption, induces profound changes in the layered GO structure: loss of stacking order, retention of trace amounts of solvents and decreasing decomposition temperature. This study presents new evidences of the effect of organic solvents on the thermal reduction of GO by means of thermogravimetric analysis, X-ray diffraction and X-ray photoelectron spectroscopy. The results reveal a relative higher decrease of the oxygen amounts in solvent-treated GO as compared to untreated GO and the restacking inhibition of the thermally reduced GO sheets upon slow heating. The kinetic experiments evidence changes occurring in the reduction mechanisms of the solvent-treated GO, which support the close link between GO structure and thermal properties.

Source apportionment by PMF on elemental concentrations obtained by PIXE analysis of PM10 samples collected at the vicinity of lignite power plants and mines in Megalopolis, Greece

International Nuclear Information System (INIS)

Manousakas, M.; Diapouli, E.; Papaefthymiou, H.; Migliori, A.; Karydas, A.G.; Padilla-Alvarez, R.; Bogovac, M.; Kaiser, R.B.; Jaksic, M.; Bogdanovic-Radovic, I.; Eleftheriadis, K.

2015-01-01

Particulate matter (PM) is an important constituent of atmospheric pollution especially in areas under the influence of industrial emissions. Megalopolis is a small city of 10,000 inhabitants located in central Peloponnese in close proximity to three coal opencast mines and two lignite fired power plants. 50 PM 10 samples were collected in Megalopolis during the years 2009–11 for elemental and multivariate analysis. For the elemental analysis PIXE was used as one of the most effective techniques in APM analytical characterization. Altogether, the concentrations of 22 elements (Z = 11–33), whereas Black Carbon was also determined for each sample using a reflectometer. Factorization software was used (EPA PMF 3.0) for source apportionment analysis. The analysis revealed that major emission sources were soil dust 33% (7.94 ± 0.27 μg/m 3 ), biomass burning 19% (4.43 ± 0.27 μg/m 3 ), road dust 15% (3.63 ± 0.37 μg/m 3 ), power plant emissions 13% (3.01 ± 0.44 μg/m 3 ), traffic 12% (2.82 ± 0.37 μg/m 3 ), and sea spray 8% (1.99 ± 0.41 μg/m 3 ). Wind trajectories have suggested that metals associated with emission from the power plants came mainly from west and were connected with the locations of the lignite mines located in this area. Soil resuspension, road dust and power plant emissions increased during the warm season of the year, while traffic/secondary, sea spray and biomass burning become dominant during the cold season

Source apportionment by PMF on elemental concentrations obtained by PIXE analysis of PM10 samples collected at the vicinity of lignite power plants and mines in Megalopolis, Greece

Science.gov (United States)

Manousakas, M.; Diapouli, E.; Papaefthymiou, H.; Migliori, A.; Karydas, A. G.; Padilla-Alvarez, R.; Bogovac, M.; Kaiser, R. B.; Jaksic, M.; Bogdanovic-Radovic, I.; Eleftheriadis, K.

2015-04-01

Particulate matter (PM) is an important constituent of atmospheric pollution especially in areas under the influence of industrial emissions. Megalopolis is a small city of 10,000 inhabitants located in central Peloponnese in close proximity to three coal opencast mines and two lignite fired power plants. 50 PM10 samples were collected in Megalopolis during the years 2009-11 for elemental and multivariate analysis. For the elemental analysis PIXE was used as one of the most effective techniques in APM analytical characterization. Altogether, the concentrations of 22 elements (Z = 11-33), whereas Black Carbon was also determined for each sample using a reflectometer. Factorization software was used (EPA PMF 3.0) for source apportionment analysis. The analysis revealed that major emission sources were soil dust 33% (7.94 ± 0.27 μg/m3), biomass burning 19% (4.43 ± 0.27 μg/m3), road dust 15% (3.63 ± 0.37 μg/m3), power plant emissions 13% (3.01 ± 0.44 μg/m3), traffic 12% (2.82 ± 0.37 μg/m3), and sea spray 8% (1.99 ± 0.41 μg/m3). Wind trajectories have suggested that metals associated with emission from the power plants came mainly from west and were connected with the locations of the lignite mines located in this area. Soil resuspension, road dust and power plant emissions increased during the warm season of the year, while traffic/secondary, sea spray and biomass burning become dominant during the cold season.

Adsorption kinetics of malachite green onto activated carbon prepared from Tuncbilek lignite

International Nuclear Information System (INIS)

Onal, Y.; Akmil-Basar, C.; Eren, Didem; Sarici-Ozdemir, Cigdem; Depci, Tolga

2006-01-01

Adsorbent (T 3 K618) has been prepared from Tuncbilek lignite by chemical activation with KOH. Pore properties of the activated carbon such as BET surface area, pore volume, pore size distribution, and pore diameter were characterized by t-plot based on N 2 adsorption isotherm. The N 2 adsorption isotherm of malachite green on T 3 K618 is type I. The BET surface area of the adsorbent which was primarily contributed by micropores was determined 1000 m 2 /g. T 3 K618 was used to adsorb malachite green (MG) from an aqueous solution in a batch reactor. The effects of initial dye concentration, agitation time, initial pH and adsorption temperature have been studied. It was also found that the adsorption isotherm followed both Freundlich and Dubinin-Radushkevich models. However, the Freundlich gave a better fit to all adsorption isotherms than the Dubinin-Radushkevich. The kinetics of adsorption of MG has been tested using pseudo-first-order, pseudo-second-order and intraparticle diffusion models. Results show that the adsorption of MG from aqueous solution onto micropores T 3 K618 proceeds according to the pseudo-second-order model. The intraparticle diffusion of MG molecules within the carbon particles was identified to be the rate-limiting step. The adsorption of the MG was endothermic (ΔH o = 6.55-62.37 kJ/mol) and was accompanied by an increase in entropy (ΔS o = 74-223 J/mol K) and a decrease in mean value of Gibbs energy (ΔG o = -6.48 to -10.32 kJ/mol) in the temperature range of 20-50 deg. C

Citric acid facilitated thermal treatment: An innovative method for the remediation of mercury contaminated soil

International Nuclear Information System (INIS)

Ma, Fujun; Peng, Changsheng; Hou, Deyi; Wu, Bin; Zhang, Qian; Li, Fasheng; Gu, Qingbao

2015-01-01

Highlights: • Hg content was reduced to <1.5 mg/kg when treated at 400 °C with citric acid. • The treated soil retained most of its original soil physicochemical properties. • Proton provided by citric acid facilitates thermal removal of mercury. • This thermal treatment method is expected to reduce energy input by 35%. - Abstract: Thermal treatment is a promising technology for the remediation of mercury contaminated soils, but it often requires high energy input at heating temperatures above 600 °C, and the treated soil is not suitable for agricultural reuse. The present study developed a novel method for the thermal treatment of mercury contaminated soils with the facilitation of citric acid (CA). A CA/Hg molar ratio of 15 was adopted as the optimum dosage. The mercury concentration in soils was successfully reduced from 134 mg/kg to 1.1 mg/kg when treated at 400 °C for 60 min and the treated soil retained most of its original soil physiochemical properties. During the treatment process, CA was found to provide an acidic environment which enhanced the volatilization of mercury. This method is expected to reduce energy input by 35% comparing to the traditional thermal treatment method, and lead to agricultural soil reuse, thus providing a greener and more sustainable remediation method for treating mercury contaminated soil in future engineering applications.

Citric acid facilitated thermal treatment: An innovative method for the remediation of mercury contaminated soil

Energy Technology Data Exchange (ETDEWEB)

Ma, Fujun [State Key Laboratory of Environmental Criteria and Risk Assessment, Chinese Research Academy of Environmental Sciences, Beijing 100012 (China); Peng, Changsheng [The Key Lab of Marine Environmental Science and Ecology, Ministry of Education, Ocean University of China, Qingdao 266100 (China); Hou, Deyi [Geotechnical and Environmental Research Group, Department of Engineering, University of Cambridge, Cambridge CB2 1PZ (United Kingdom); Wu, Bin; Zhang, Qian; Li, Fasheng [State Key Laboratory of Environmental Criteria and Risk Assessment, Chinese Research Academy of Environmental Sciences, Beijing 100012 (China); Gu, Qingbao, E-mail: guqb@craes.org.cn [State Key Laboratory of Environmental Criteria and Risk Assessment, Chinese Research Academy of Environmental Sciences, Beijing 100012 (China)

2015-12-30

Highlights: • Hg content was reduced to <1.5 mg/kg when treated at 400 °C with citric acid. • The treated soil retained most of its original soil physicochemical properties. • Proton provided by citric acid facilitates thermal removal of mercury. • This thermal treatment method is expected to reduce energy input by 35%. - Abstract: Thermal treatment is a promising technology for the remediation of mercury contaminated soils, but it often requires high energy input at heating temperatures above 600 °C, and the treated soil is not suitable for agricultural reuse. The present study developed a novel method for the thermal treatment of mercury contaminated soils with the facilitation of citric acid (CA). A CA/Hg molar ratio of 15 was adopted as the optimum dosage. The mercury concentration in soils was successfully reduced from 134 mg/kg to 1.1 mg/kg when treated at 400 °C for 60 min and the treated soil retained most of its original soil physiochemical properties. During the treatment process, CA was found to provide an acidic environment which enhanced the volatilization of mercury. This method is expected to reduce energy input by 35% comparing to the traditional thermal treatment method, and lead to agricultural soil reuse, thus providing a greener and more sustainable remediation method for treating mercury contaminated soil in future engineering applications.

Thermal Plumes in Ventilated Rooms

DEFF Research Database (Denmark)

Kofoed, Peter

Axisymmeric circular buoyant jets are treated both theoretically and experimentally. From a literature study the author concludes that the state of experimental knowledge is less satisfactory. Further three different measuring methods have been established to investigate the thermal plumes from...

Analysis of lithofacies cyclicity in the Miocene Coal Complex of the Bełchatów lignite deposit, south-central Poland

Directory of Open Access Journals (Sweden)

Mastej Wojciech

2015-12-01

Full Text Available Markov chain analysis was applied to studies of cyclic sedimentation in the Coal Complex of the Bełchatów mining field (part of the Bełchatów lignite deposit. The majority of ambiguous results of statistical testing that were caused by weak, statistically undetectable advantage of either cyclicity over environmental barriers or vice versa, could be explained if only the above-mentioned advantages appeared in the neighbourhood. Therefore, in order to enhance the credibility of statistical tests, a new approach is proposed here in that matrices of observed transition numbers from different boreholes should be added to increase statistical reliability if they originated in a homogeneous area. A second new approach, which consists of revealing statistically undetectable cyclicity of lithofacies alternations, is proposed as well. All data were derived from the mining data base in which differentiation between lithology and sedimentary environments was rather weak. For this reason, the methodological proposals are much more important than details of the sedimentation model in the present paper. Nevertheless, they did reveal some interesting phenomena which may prove important in the reconstruction of peat/lignite environmental conditions. First of all, the presence of cyclicity in the sedimentation model, i.e., cyclic alternation of channel and overbank deposits, represents a fluvial environment. It was also confirmed that the lacustrine subenvironment was cut off from a supply of clastic material by various types of mire barriers. Additionally, our analysis revealed new facts: (i these barriers also existed between lakes in which either carbonate or clay sedimentation predominated; (ii there was no barrier between rivers and lakes in which clay sedimentation predominated; (iii barriers were less efficient in alluvial fan areas but were perfectly tight in regions of phytogenic or carbonate sedimentation; (iv groundwater, rather than surface flow

Using radon-222 for tracing groundwater discharge into an open-pit lignite mining lake--a case study.

Science.gov (United States)

Schmidt, Axel; Schubert, Michael

2007-12-01

Groundwater discharge into an open pit lignite mining lake was investigated using radon-222 as a naturally occurring environmental tracer. The chosen study site was a meromictic lake, i.e., a water body that is divided horizontally into two separate layers--the upper mixolimnion (with seasonal mixing) and the lower monimolimnion (without seasonal mixing). For the estimation of groundwater discharge rates into the lake, a simple box model including all radon sinks and sources related to each layer was applied. Two field investigations were performed. During the October campaign, the total groundwater discharge into the lake was found to be 18.9 and 0.7 m(3) d(-1) for the mixolimnion and monimolimnion, respectively. During the December campaign, the groundwater discharge into the mixolimnion was 15.0 m(3) d(-1), whereas no discharge at all was observed into the monimolimnion. Based on the given water volumes, the residence time of lake water was 5.3 years for the monimolimnion and varies between 0.9 and 1.1 years for the mixolimnion. The investigation confirmed radon to be a useful environmental tracer for groundwater and surface water interactions in meromictic lake environments.

Operational experience of electron beam flue gases treatment pilot installation at the Maritsa East 2 Thermal Power Plant

Energy Technology Data Exchange (ETDEWEB)

Dutskinov, N. [NEK-EAD (Bulgaria)

2011-07-01

The electron beam flue gases treatment process is very versatile and effective technology for simultaneous removal of acidic pollutants i.e. sulfur dioxide (SO{sub 2}) and nitrogen oxide (NO{sub x}) from the flue gas produced in the combustion of fossil fuel. The technology allows decomposition of VOC (volatile organic compound) such as polycyclic aromatic compound (PAC) and persistent organic pollutants (POP). The electron beam flue gases treatment technology for combustion flue gases purification was applied in Maritsa-East 2 Thermal Power Plant. The decision for construction of Electron Beam Pilot Plant at Maritsa-East 2 TPP was taken at the technical meeting in IAEA Vienna, November 1998. The flue gases of 10 000 nm³/h are irradiated by three high energy electron accelerators of 800 keV and 35 kW beam power each. The plant has been operated since November 2003. The removal efficiency 90-99% for SO{sub x} and 85-90% for NO{sub x} was observed. The quality of coals are characterised with high ash content up to 45%, high moisture up to 57%, low calorific value from 1196 kcal/kg up to 1603 kcal/kg and high concentration of sulphur. The Bulgarian lignite coals are unique in their usage as fuel for the thermal power plants in Maritsa East region. (author)

The taphonomy of a remarkable leaf bed assemblage from the Late Oligocene-Early Miocene Gore Lignite Measures, southern New Zealand

Energy Technology Data Exchange (ETDEWEB)

Ferguson, David K.; Zetter, Reinhard; Vavra, Norbert [Department of Paleontology, University of Vienna, Althanstrasse 14, A-1090 Vienna (Austria); Lee, Daphne E. [Department of Geology, University of Otago, PO Box 56, Dunedin (New Zealand); Bannister, Jennifer M. [Department of Botany, University of Otago, PO Box 56, Dunedin (New Zealand); Jordan, Gregory J. [School of Plant Sciences, University of Tasmania, Private Bag 55, Hobart, Tasmania 7001 (Australia); Mildenhall, Dallas C. [GNS Science, PO Box 30-368, Lower Hutt (New Zealand)

2010-08-01

A diverse assemblage of fossil leaves showing cellular detail is reported from the Late Oligocene-Early Miocene Gore Lignite Measures, southern New Zealand. The leaf-remains include at least five conifers, such as the genera Agathis, Dacrycarpus, Phyllocladus and Dacrydium, as well as a number of angiosperms including Gymnostoma, Nothofagus Subgenus Brassospora, Phormium, Proteaceae, Sapindaceae and Ericaceae. A parallel palynological study has identified a number of the same elements. The leaf layers represent litter horizons laid down in pools on the surface of a subtropical ombrotrophic forest mire that formed on an extensive low-lying coastal plain. Highly acidic water ponded in tree-fall depressions prevented microbial decay of the foliage. Taxa represented by both leaves and pollen are considered to have been components of the autochthonous swamp forest. Some other pollen grains are thought to represent local elements, based on the pollination biology of their nearest living relatives. Other taxa whose extant representatives are wind-pollinated may have grown further away. (author)

Sequential simulation approach to modeling of multi-seam coal deposits with an application to the assessment of a Louisiana lignite

Science.gov (United States)

Olea, Ricardo A.; Luppens, James A.

2012-01-01

There are multiple ways to characterize uncertainty in the assessment of coal resources, but not all of them are equally satisfactory. Increasingly, the tendency is toward borrowing from the statistical tools developed in the last 50 years for the quantitative assessment of other mineral commodities. Here, we briefly review the most recent of such methods and formulate a procedure for the systematic assessment of multi-seam coal deposits taking into account several geological factors, such as fluctuations in thickness, erosion, oxidation, and bed boundaries. A lignite deposit explored in three stages is used for validating models based on comparing a first set of drill holes against data from infill and development drilling. Results were fully consistent with reality, providing a variety of maps, histograms, and scatterplots characterizing the deposit and associated uncertainty in the assessments. The geostatistical approach was particularly informative in providing a probability distribution modeling deposit wide uncertainty about total resources and a cumulative distribution of coal tonnage as a function of local uncertainty.

Effect of aluminum anodizing in phosphoric acid electrolyte on adhesion strength and thermal performance

Science.gov (United States)

Lee, Sulki; Kim, Donghyun; Kim, Yonghwan; Jung, Uoochang; Chung, Wonsub

2016-01-01

This study examined the adhesive bond strength and thermal performance of the anodized aluminum 6061 in phosphoric acid electrolyte to improve the adhesive bond strength and thermal performance for use in metal core printed circuit boards (MCPCB). The electrolyte temperature and applied voltage were altered to generate varied pore structures. The thickness, porosity and pore diameter of the anodized layer were measured. The pore morphologies were affected most by temperature, which was the driving force for ion transportation. The mechanism of adhesive bond was penetration of the epoxy into the pores. The optimal anodization conditions for maximum adhesive bond strength, 27 MPa, were 293 K and 100V. The maximum thermal conductivity of the epoxy-treated anodized layer was 1.6 W/m·K at 273 K. Compared with the epoxy-treated Al layer used for conventional MCPCBs, the epoxy-treated anodized layer showed advanced thermal performance due to a low difference of thermal resistance and high heat dissipation.

Comparison of LIFE-4 and TEMECH code predictions with TREAT transient test data

International Nuclear Information System (INIS)

Gneiting, B.C.; Bard, F.E.; Hunter, C.W.

1984-09-01

Transient tests in the TREAT reactor were performed on FFTF Reference design mixed-oxide fuel pins, most of which had received prior steady-state irradiation in the EBR-II reactor. These transient test results provide a data base for calibration and verification of fuel performance codes and for evaluation of processes that affect pin damage during transient events. This paper presents a comparison of the LIFE-4 and TEMECH fuel pin thermal/mechanical analysis codes with the results from 20 HEDL TREAT experiments, ten of which resulted in pin failure. Both the LIFE-4 and TEMECH codes provided an adequate representation of the thermal and mechanical data from the TREAT experiments. Also, a criterion for 50% probability of pin failure was developed for each code using an average cumulative damage fraction value calculated for the pins that failed. Both codes employ the two major cladding loading mechanisms of differential thermal expansion and central cavity pressurization which were demonstrated by the test results. However, a detailed evaluation of the code predictions shows that the two code systems weigh the loading mechanism differently to reach the same end points of the TREAT transient results

A Raman spectroscopic study of thermally treated glushinskite--the natural magnesium oxalate dihydrate.

Science.gov (United States)

Frost, Ray L; Adebajo, Moses; Weier, Matt L

2004-02-01

Raman spectroscopy has been used to study the thermal transformations of natural magnesium oxalate dihydrate known in mineralogy as glushinskite. The data obtained by Raman spectroscopy was supplemented with that of infrared emission spectroscopy. The vibrational spectroscopic data was complimented with high resolution thermogravimetric analysis combined with evolved gas mass spectrometry. TG-MS identified two mass loss steps at 146 and 397 degrees C. In the first mass loss step water is evolved only, in the second step carbon dioxide is evolved. The combination of Raman microscopy and a thermal stage clearly identifies the changes in the molecular structure with thermal treatment. Glushinskite is the dihydrate phase in the temperature range up to the pre-dehydration temperature of 146 degrees C. Above 397 degrees C, magnesium oxide is formed. Infrared emission spectroscopy shows that this mineral decomposes at around 400 degrees C. Changes in the position and intensity of the CO and CC stretching vibrations in the Raman spectra indicate the temperature range at which these phase changes occur.

Smart thermal patch for adaptive thermotherapy

KAUST Repository

Hussain, Muhammad Mustafa

2015-11-12

A smart thermal patch for adaptive thermotherapy is provided. In an embodiment, the patch can be a stretchable, non-polymeric, conductive thin film flexible and non-invasive body integrated mobile thermal heater with wireless control capabilities that can be used to provide adaptive thermotherapy. The patch can be geometrically and spatially tunable on various pain locations. Adaptability allows the amount of heating to be tuned based on the temperature of the treated portion.

Structural Design Optimization On Thermally Induced Vibration

International Nuclear Information System (INIS)

Gu, Yuanxian; Chen, Biaosong; Zhang, Hongwu; Zhao, Guozhong

2002-01-01

The numerical method of design optimization for structural thermally induced vibration is originally studied in this paper and implemented in application software JIFEX. The direct and adjoint methods of sensitivity analysis for thermal induced vibration coupled with both linear and nonlinear transient heat conduction is firstly proposed. Based on the finite element method, the structural linear dynamics is treated simultaneously with coupled linear and nonlinear transient heat structural linear dynamics is treated simultaneously with coupled linear and nonlinear transient heat conduction. In the thermal analysis model, the nonlinear heat conduction considered is result from the radiation and temperature-dependent materials. The sensitivity analysis of transient linear and nonlinear heat conduction is performed with the precise time integration method. And then, the sensitivity analysis of structural transient dynamics is performed by the Newmark method. Both the direct method and the adjoint method are employed to derive the sensitivity equations of thermal vibration, and there are two adjoint vectors of structure and heat conduction respectively. The coupling effect of heat conduction on thermal vibration in the sensitivity analysis is particularly investigated. With coupling sensitivity analysis, the optimization model is constructed and solved by the sequential linear programming or sequential quadratic programming algorithm. The methods proposed have been implemented in the application software JIFEX of structural design optimization, and numerical examples are given to illustrate the methods and usage of structural design optimization on thermally induced vibration

A diverse snake fauna from the early Eocene of Vastan Lignite Mine, Gujarat, India

Energy Technology Data Exchange (ETDEWEB)

Rage, J.C.; Folie, A.; Rana, R.S.; Singh, H.; Rose, K.D.; Smith, T. [Museum National Historical Nature, Paris (France)

2008-09-15

The early Eocene (Ypresian) Cambay Formation of Vastan Lignite Mine in Gujarat, western India, has produced a diverse assemblage of snakes including at least ten species that belong to the Madtsoiidae, Palaeophiidae (Palaeophis and Pterosphenus), Boidae, and several Caenophidia. Within the latter taxon, the Colubroidea are represented by Russellophis crassus sp. nov. (Russellophiidae) and by Procerophis sahnii gen. et sp. nov. Thaumastophis missiaeni gen. et sp. nov. is a caenophidian of uncertain family assignment. At least two other forms probably represent new genera and species, but they are not named; both appear to be related to the Caenophidia. The number of taxa that represent the Colubroidea or at least the Caenophidia, i.e., advanced snakes, is astonishing for the Eocene. This is consistent with the view that Asia played an important part in the early history of these taxa. The fossils come from marine and continental levels; however, no significant difference is evident between faunas from these levels. The fauna from Vastan Mine includes highly aquatic, amphibious, and terrestrial snakes. All are found in the continental levels, including the aquatic palaeophiids, whereas the marine beds yielded only two taxa. Vastan Mine is only the second locality in which the palaeophiids Palaeophis and Pterosphenus co-occur. The composition of the fauna from Vastan is on the whole similar to that of the early Eocene of Europe; however, comparisons with early Eocene faunas of other continents are not possible because they are poorly known or unknown.

Initial screening of thermal desorption for soil remediation

International Nuclear Information System (INIS)

Yezzi, J.J. Jr.; Tafuri, A.N.; Rosenthal, S.; Troxler, W.L.

1994-01-01

Petroleum-contaminated soils--caused by spills, leaks, and accidental discharges--exist at many sites throughout the United States. Thermal desorption technologies which are increasingly being employed to treat these soils, have met soil cleanup criteria for a variety of petroleum products. Currently the United States Environmental Protection Agency is finalizing a technical report entitled Use of Thermal Desorption for Treating Petroleum-Contaminated Soils to assist remedial project managers, site owners, remediation contractors, and equipment vendors in evaluating the use of thermal desorption technologies for petroleum-contaminated soil applications. The report will present a three-level screening method to help a reader predict the success of applying thermal desorption at a specific site. The objective of screening level one is to determine the likelihood of success in a specific application of thermal desorption. It will take into account procedures for collecting and evaluating data on site characteristics, contaminant characteristics, soil characteristics, and regulatory requirements. This level will establish whether or not thermal desorption should be evaluated further for site remediation, whether treatment should occur on-site or off-site, and if on-site is a viable option, what system size will be most cost-effective. The scope of this paper addresses only screening level one which provides a preliminary assessment of the applicability of thermal desorption to a particular site. This topic encompasses worksheets that are an integral part of the ''user friendly'' screening process. Level one screening provides a foundation for the subsequent two levels which follow a similar ''user friendly'' worksheet approach to evaluating thermal desorption technologies and establishing costs for thermal desorption in an overall remediation project

Leaching from waste incineration bottom ashes treated in a rotary kiln

DEFF Research Database (Denmark)

Hyks, Jiri; Nesterov, Igor; Mogensen, Erhardt

2011-01-01

Leaching from municipal solid waste incineration bottom ash treated in a rotary kiln was quantified using a combination of lab-scale leaching experiments and geochemical modelling. Thermal treatment in the rotary kiln had no significant effect on the leaching of Al, Ba, Ca, Mg, Si, Sr, Zn, sulfate...... the thermal treatment. Overall, rotary kiln thermal treatment of bottom ashes can be recommended to reduce the leaching of Cu, Pb, Cl and DOC; however, increased leaching of Cr and Mo should be expected....

Determination of phenol in tar

Energy Technology Data Exchange (ETDEWEB)

Dierichs, A; Heinichen, G

1955-01-01

During low-temperature carbonization of lignite, the phenols and other oxygenated compounds appear both in the aqueous-process liquor and in the tar. Measurements of these oxygenated components resulting from low-temperature carbonization may serve as a parameter for the classification of lignites. However, such measurements are complicated by the instability of the tar and the complex nature of some of the acidic substances. Difficulties with the previous methods of analysis are reviewed. The present method outlines separation of aqueous-process liquor from lignite tar in a Fischer retort, followed by determination of phenols and fatty acids in the tar phase. The jacketed tar receiver is washed with 300 milliliter xylol and treated with aqueous caustic washes. Neutral oils are separated from the aqueous alkali solution. It is then extracted with ether and finally acidified with HCl. Solids are filtered off, and phenols and fatty acids are separated by Na/sub 2/CO/sub 3/ solution.

Low NOx firing systems for bituminous coal and lignite

International Nuclear Information System (INIS)

Knyrim, W.; Scheffknecht, G.

1997-01-01

In the case of lignite fluidized boilers the denitrification down to less than 200 mg/m 3 was possible with primary measures on the firing side only. On account of the excellent results achieved with the reconstructed plants the firing systems for the new generation of brown coal fire steam generators with a capacity of 800 MW and more is designed in a similar way. For bituminous coal fire steam generators the primary measures on the firing side are nor sufficient to keep the German NO x emission limit. Therefore these units had to be retrofitted with a SCR-DENOX plant. The experience with the new firing system made in a 110 MW steam generator in Austria with a wide range of fuels is introduced. One of the largest bituminous coal fired once-trough steam generator built by EVT is the boiler for the power station Bexbach I (750 MW). The firing system is designed as a tangential firing system with 32 jet burners. These are arranged in pairs in the corners and divided into 4 burner levels with 4 burner pairs each. One mill is allocated to each burner level. An important characteristic feature is that the four bowl mills are arranged on one side of the steam generator. The plant is constructed with upper air nozzles which are arranged above the top burner level for the reduced of nitrogen oxides. During tests at steam generator with similar design, the nO x formation could be reduced from 750 to 500 mg/m 3 s.t.p. (dry, 6% O 2 ) with an addition of upper air of 20% at 100% unit capacity and constant total flow. As a main approach for the further reduction of the primary NO x emission at bituminous coal fired steam generators with tangential firing systems, the experience gained from the firing of brown coal has also been taken into account. A fundamental aspect in this respect was the vertical air staging in the direction of the furnace height. The results of many tests in a test reactor have shown that the differences of the achievable NO x values of brown and

Dust precipitation nuisance in the Rhine lignite basin. Situation analysis, legal assessment and the use of compost recycling for emission-protection purposes; Die Staubniederschlagsbelastungen im Rheinischen Braunkohlenrevier. Situationsanalyse, rechtliche Bewertung und Verwertung von Kompost zu Immissionsschutzzwecken

Energy Technology Data Exchange (ETDEWEB)

Asenbaum, P. [Bergamt Dueren (Germany)

2004-03-01

The paper describes the problem of dust precipitation in the Rhine lignite basin and presents a legal, scientific and technical assessment of how composting can be used for emission protection purposes, along with supporting measures such as the replanting of opencast mining sites. Also examines the benefits, and possible risks, associated with waste recycling projects of this kind. The results of the investigations show that compost recycling for emission-protection purposes can be used to support the emission-protection measures previously deployed at opencast mines in the Rhine lignite basin, including the grassing-over of former mine sites. Such measures are now considered to be technically feasible, environmentally compatible and lawful, and indeed are considered necessary in some circumstances. (orig.) [German] Die Arbeit beschreibt die Staubniederschlagsbelastungen im Rheinischen Braunkohlenrevier und bewertet in diesem Zusammenhang den Einsatz von Kompost zu Immissionsschutzzwecken einschliesslich einer unterstuetzenden Begruenung in den Tagebauen in rechtlicher sowie naturwissenschaftlich-technischer Hinsicht. Darueber hinaus wird die Nuetzlichkeit und Schadlosigkeit dieser Abfallverwertungsmassnahmen beurteilt. Nach den Ergebnissen dieser Arbeit ist eine Kompostverwertung zu Immissionsschutzzwecken zur Ergaenzung des bisherigen Immissionsschutzsystems in den Tagebauen des Rheinischen Braunkohlenreviers einschliesslich einer unterstuetzenden Begruenung technisch moeglich, umweltvertraeglich und rechtlich zulaessig sowie unter bestimmten Voraussetzungen erforderlich. (orig.)

Cemented carbide cutting tool: Laser processing and thermal stress analysis

Energy Technology Data Exchange (ETDEWEB)

Yilbas, B.S. [Mechanical Engineering Department, KFUPM, Box 1913, Dhahran 31261 (Saudi Arabia)]. E-mail: bsyilbas@kfupm.edu.sa; Arif, A.F.M. [Mechanical Engineering Department, KFUPM, Box 1913, Dhahran 31261 (Saudi Arabia); Karatas, C. [Engineering Faculty, Hacettepe University, Ankara (Turkey); Ahsan, M. [Mechanical Engineering Department, KFUPM, Box 1913, Dhahran 31261 (Saudi Arabia)

2007-04-15

Laser treatment of cemented carbide tool surface consisting of W, C, TiC, TaC is examined and thermal stress developed due to temperature gradients in the laser treated region is predicted numerically. Temperature rise in the substrate material is computed numerically using the Fourier heating model. Experiment is carried out to treat the tool surfaces using a CO{sub 2} laser while SEM, XRD and EDS are carried out for morphological and structural characterization of the treated surface. Laser parameters were selected include the laser output power, duty cycle, assisting gas pressure, scanning speed, and nominal focus setting of the focusing lens. It is found that temperature gradient attains significantly high values below the surface particularly for titanium and tantalum carbides, which in turn, results in high thermal stress generation in this region. SEM examination of laser treated surface and its cross section reveals that crack initiation below the surface occurs and crack extends over the depth of the laser treated region.

Management of Lignite Fly Ash for Improving Soil Fertility and Crop Productivity

Science.gov (United States)

Ram, Lal C.; Srivastava, Nishant K.; Jha, Sangeet K.; Sinha, Awadhesh K.; Masto, Reginald E.; Selvi, Vetrivel A.

2007-09-01

Lignite fly ash (LFA), being alkaline and endowed with excellent pozzolanic properties, a silt loam texture, and plant nutrients, has the potential to improve soil quality and productivity. Long-term field trials with groundnut, maize, and sun hemp were carried out to study the effect of LFA on growth and yield. Before crop I was sown, LFA was applied at various doses with and without press mud (an organic waste from the sugar industry, used as an amendment and source of nutrients). LFA with and without press mud was also applied before crops III and V were cultivated. Chemical fertilizer, along with gypsum, humic acid, and biofertilizer, was applied in all treatments, including the control. With one-time and repeat applications of LFA (with and without press mud), yield increased significantly (7.0-89.0%) in relation to the control crop. The press mud enhanced the yield (3.0-15.0%) with different LFA applications. The highest yield LFA dose was 200 t/ha for one-time and repeat applications, the maximum yield being with crop III (combination treatment). One-time and repeat application of LFA (alone and in combination with press mud) improved soil quality and the nutrient content of the produce. The highest dose of LFA (200 t/ha) with and without press mud showed the best residual effects (eco-friendly increases in the yield of succeeding crops). Some increase in trace- and heavy-metal contents and in the level of γ-emitters in soil and crop produce, but well within permissible limits, was observed. Thus, LFA can be used on a large scale to boost soil fertility and productivity with no adverse effects on the soil or crops, which may solve the problem of bulk disposal of fly ash in an eco-friendly manner.

40 CFR 63.7575 - What definitions apply to this subpart?

Science.gov (United States)

2010-07-01

... monitor relative particulate matter loadings. Biomass fuel means unadulterated wood as defined in this... 51.24. Firetube boiler means a boiler that utilizes a containment shell that encloses firetubes..., lignite, anthracite, biomass, construction/demolition material, salt water laden wood, creosote treated...

Glucose-Treated Manganese Hexacyanoferrate for Sodium-Ion Secondary Battery

OpenAIRE

Moritomo, Yutaka; Goto, Kensuke; Shibata, Takayuki

2015-01-01

Manganese hexacyanoferrate (Mn-PBA) is a promising cathode material forsodium-ion secondary battery (SIB) with high average voltage (=3.4 V) against Na. Here,we find that the thermal decomposition of glucose modifies the surface state of Mn-PBA,without affecting the bulk crystal structure. The glucose treatment significantly improves therate properties of Mn-PBA in SIB. The critical discharge rate increases from 1 C (as-grown)to 15 C (glucose-treated). Our observation suggests that thermal tr...

Low thermal expansion glass ceramics

CERN Document Server

1995-01-01

This book is one of a series reporting on international research and development activities conducted by the Schott group of companies With the series, Schott aims to provide an overview of its activities for scientists, engineers, and managers from all branches of industry worldwide where glasses and glass ceramics are of interest Each volume begins with a chapter providing a general idea of the current problems, results, and trends relating to the subjects treated This volume describes the fundamental principles, the manufacturing process, and applications of low thermal expansion glass ceramics The composition, structure, and stability of polycrystalline materials having a low thermal expansion are described, and it is shown how low thermal expansion glass ceramics can be manufactured from appropriately chosen glass compositions Examples illustrate the formation of this type of glass ceramic by utilizing normal production processes together with controlled crystallization Thus glass ceramics with thermal c...

Acoustic and thermal properties of tissue

Science.gov (United States)

Retat, L.; Rivens, I.; ter Haar, G. R.

2012-10-01

Differences in ultrasound (US) and thermal properties of abdominal soft tissues may affect the delivery of thermal therapies such as high intensity focused ultrasound and may provide a basis for US monitoring of such therapies. 21 rat livers were obtained, within one hour of surgical removal. For a single liver, 3 lobes were selected and each treated in one of 3 ways: maintained at room temperature, water bath heated to 50°C ± 1°C for 10 ± 0.5 minutes, or water bath heated to 60°C ± 1°C for 10 ± 0.6 minutes. The attenuation coefficient, speed of sound and thermal conductivity of fresh rat liver was measured. The attenuation coefficients and speed of sound were measured using the finite-amplitude insertion-substitution (FAIS) method. For each rat liver, the control and treated lobes were scanned using a pair of weakly focused 2.5 MHz Imasonic transducers over the range 1.8 to 3 MHz. The conductivity measurement apparatus was designed to provide one-dimensional heat flow through each specimen using a combination of insulation, heat source and heat sink. Using 35 MHz US images to determine the volume of air trapped in the system, the thermal conductivity was corrected using a simulation based on the Helmhotz bio-heat equation. The process of correlating these results with biological properties is discussed.

Effect of thermal-treatment sequence on sound absorbing and mechanical properties of porous sound-absorbing/thermal-insulating composites

Directory of Open Access Journals (Sweden)

Huang Chen-Hung

2016-01-01

Full Text Available Due to recent rapid commercial and industrial development, mechanical equipment is supplemented massively in the factory and thus mechanical operation causes noise which distresses living at home. In livelihood, neighborhood, transportation equipment, jobsite construction noises impact on quality of life not only factory noise. This study aims to preparation technique and property evaluation of porous sound-absorbing/thermal-insulating composites. Hollow three-dimensional crimp PET fibers blended with low-melting PET fibers were fabricated into hollow PET/low-melting PET nonwoven after opening, blending, carding, lapping and needle-bonding process. Then, hollow PET/low-melting PET nonwovens were laminated into sound-absorbing/thermal-insulating composites by changing sequence of needle-bonding and thermal-treatment. The optimal thermal-treated sequence was found by tensile strength, tearing strength, sound-absorbing coefficient and thermal conductivity coefficient tests of porous composites.

Thermal Conversion of Pine Wood Char to Carbon Nanomaterials in the Presence of Iron Nanoparticles

Science.gov (United States)

Sung Phil Mun; Zhiyong Cai; Fumiya Watanabe; Umesh P. Agarwal; Jilei. Zhang

2012-01-01

Southern yellow pine (Pinus taeda) wood char powder was thermally treated at 1,000:C in the presence of a 25-nm-size Fe nanoparticle catalyst. The thermally treated carbon materials were analyzed by Raman spectroscopy and high-resolution transmission electron microscopy. Well-aligned graphitic carbon structures with 15 to 17 layers on...

Thermal degradation of ethanolic biodiesel: Physicochemical and thermal properties evaluation

International Nuclear Information System (INIS)

Silva, Wellington Costa; Castro, Maria Priscila Pessanha; Perez, Victor Haber; Machado, Francisco A.; Mota, Leonardo; Sthel, Marcelo Silva

2016-01-01

The aim of this paper was to study the thermal degradation of soybean biodiesel attained by ethanolic route. The soybean biodiesel samples were subjected to heating treatment at 150 °C for 24 h in a closed oven under controlled atmosphere. During the experiments, samples were withdrawn at intervals of 3, 6, 9, 12, 15 and 24 h for physicochemical and thermophysical properties analysis. The biodiesel degradation was validated by Thermogravimetric analysis since their profiles for control and treated biodiesel were different. Also, "1H NMR confirmed this result due to a significant reduction at the signals related to the "1H located near to the double bonds in the unsaturated ethyl esters in agreement with an iodine index reduction and viscosity increase observed during degradation. Nevertheless, degraded biodiesel, under study conditions, preserved its thermophysical properties. These results may be relevant to qualify the produced biodiesel quality and collect physicochemical and thermophysical data important for applications in combustion studies including project of fuel injection systems. - Highlights: • Soybean biodiesel from ethanolic route was subjected to thermal degradation to verify its stability. • Thermal degradation of biodiesel was correlated with physicochemical properties. • Thermal effusivity, diffusivity and conductivity were estimate by photothermal techniques.

Studies on thermal degradation and termite resistant properties of chemically modified wood

Energy Technology Data Exchange (ETDEWEB)

Deka, M.; Saikia, C.N. [Council for Scientific and Industrial Research (CSIR), Regional Research Laboratory, Jorhat (India); Baruah, K.K. [Assam Agricultural University, Jorhat (India)

2002-09-01

A series of experiments were carried out to examine the resistant capacity of a chemically treated hard wood, Anthocephalus cadamba (Roxb) Miq. to thermal and termite degradation. The treatment with thermosetting resins viz. urea formaldehyde (UF), melamine formaldehyde (MF) and phenol formaldehyde (PF) at 31-33 levels of weight percent gain (WPG) increased the strength property i.e. modulus of rupture (MOR) by 7.50-21.02% and stiffness i.e. modulus of elasticity (MOE) by 9.50-12.18% over the untreated one with no remarkable effect on specific gravity. The treated samples were found resistant to termite attack, while the untreated one was badly damaged by termites on 12 months' exposure to a termite colony. The thermal degradations of untreated and treated wood samples were studied using thermogravimetric (TGA) and differential thermogravimetric (DTG) techniques at heating rates 20 and 30 {sup o}Cmin{sup -1} in temperature range 30-650{sup o}C. The treated wood was found to be thermally more stable than the untreated one. (author)

Transient Diabetes Insipidus Following Thermal Burn; A Case Report and Literature Review.

Science.gov (United States)

Dash, Suvashis; Ghosh, Shibajyoti

2017-10-01

Diabetes insipidus is a disease charaterised by increased urine production and thrist. Neurogenic diabetes insipidus following head trauma,autoimmune disease and infection is quite common but diabetes insipidus following thermal burn injury is a rare complication.We should know about this complication as its management need a comprehensive approach for satisfactory outcome. Thermal burn can cause different complications in early post burn period like electrolyte imbalance, dehydration, acute renal failure, but diabetes insipidus is a very rare and unusual complication that may come across in thermal burn. We should be aware about this condition to prevent and treat mortality and morbidity in burn patients. We have reported a case of transient diabetes insipidus in a patient of thermal burn in early post burn period. Patient was treated accordingly, leading to complete recovery.

Multi-criteria evaluation and priority analysis for localization equipment in a thermal power plant using the AHP (analytic hierarchy process)

International Nuclear Information System (INIS)

Yagmur, Levent

2016-01-01

Ensuring the safety of its energy supply is one of the main issues for newly industrialized/developing countries when utilizing domestic sources for electricity generation. Turkey depends heavily on imported gas to generate electricity, and the ratio of natural gas power generation to total electricity production is nearly 50%. Coal-fired thermal power plants using domestic resources are considered a good option to decrease the large amount of imported natural gas, and to supply a secure energy demand. However, electricity generation from coal-fired power plants using local lignite reserves is not adequate to maintain a secure energy mix and provide sustainable development, as Turkey does not have indigenous energy sector technology. Therefore, technology transfer and its localization are crucial for newly industrialized/developing countries such as Turkey. The aim of this study is to use the analytic hierarchy process to determine a priority analysis in relation to localization equipment for a thermal power plant. Parameters involved, such as readiness of both infrastructure and human resources, manpower as skilled labor, market potential for equipment developed by transferred technology, and competition in global/internal market, are related to localization in thermal power plant technologies, and are considered in relation to the country's technological capability, design ability, possession of materials/equipment, and ability to erect a plant. Results of analysis show that the boiler is the most important piece of equipment in this respect, and that heaters and fans are ranked after the boiler with respect to local conditions. - Highlights: • Localization of foreign technology was determined for developing countries. • An evaluation and priority analysis were performed for parts of a thermal power plant. • Analytic hierarchy process was applied for the hierarchical ordering of parts when transferring technology.

Assessing the impact of primary measures for NOx reduction on the thermal power plant steam boiler

International Nuclear Information System (INIS)

Stupar, Goran; Tucaković, Dragan; Živanović, Titoslav; Belošević, Srdjan

2015-01-01

The European normatives prescribe content of 200 mg/Nm 3 NO x for pulverized coal combusting power plants. In order to reduce content of NO x in Serbian thermal power plant (TPP) 'Kostolac B' it's necessary to implement particular measures until 2016. The mathematical model of lignite combustion in the steam boiler furnace is defined and applied to analyze the possibility of implementing certain primary measures for reducing nitrogen oxides and their effects on the steam boiler operation. This model includes processes in the coal-fired furnace and defines radiating reactive two-phase turbulent flow. The model of turbulent flow also contains sub-model of fuel and thermal NO x formation and destruction. This complex mathematical model is related to thermal and aerodynamic calculations of the steam boiler within a unified calculation system in order to analyze the steam boiler overall work. This system provides calculations with a number of influential parameters. The steam boiler calculations for unit 1 (350 MWe) of TPP 'Kostolac B' are implemented for existing and modified combustion system in order to achieve effective, reliable and ecological facility work. The paper presents the influence analysis of large number of parameters on the steam boiler operation with an accepted concept of primary measures. Presented system of calculations is verified against measurements in TPP 'Kostolac B'. - Highlights: • Modern steam boilers need to operate according to ecological standards. • Possibility of applying some of the primary measures of NO x reduction. • Conventional calculations have no possibility to estimate sub-stoichiometric combustion. • Develop a new method of connecting the calculations. • Analysis shows the most favorable operation boiler regime (efficiency and ecology)

Influences of thermal decontamination on mercury removal, soil properties, and repartitioning of coexisting heavy metals.

Science.gov (United States)

Huang, Yu-Tuan; Hseu, Zeng-Yei; Hsi, Hsing-Cheng

2011-08-01

Thermal treatment is a useful tool to remove Hg from contaminated soils. However, thermal treatment may greatly alter the soil properties and cause the coexisting contaminants, especially trace metals, to transform and repartition. The metal repartitioning may increase the difficulty in the subsequent process of a treatment train approach. In this study, three Hg-contaminated soils were thermally treated to evaluate the effects of treating temperature and duration on Hg removal. Thermogravimetric analysis was performed to project the suitable heating parameters for subsequent bench-scale fixed-bed operation. Results showed that thermal decontamination at temperature>400°C successfully lowered the Hg content tosoil particle size was less significant, even when the soils were thermally treated to 550°C. Soil clay minerals such as kaolinite were shown to be decomposed. Aggregates were observed on the surface of soil particles after the treatment. The heavy metals tended to transform into acid-extractable, organic-matter bound, and residual forms from the Fe/Mn oxide bound form. These results suggest that thermal treatment may markedly influence the effectiveness of subsequent decontamination methods, such as acid washing or solvent extraction. Copyright © 2011 Elsevier Ltd. All rights reserved.

The thermal properties of a carbon nanotube-enriched epoxy: Thermal conductivity, curing, and degradation kinetics

KAUST Repository

Ventura, Isaac Aguilar

2013-05-31

Multiwalled carbon nanotube-enriched epoxy polymers were prepared by solvent evaporation based on a commercially available epoxy system and functionalized multiwalled carbon nanotubes (COOH-MWCNTs). Three weight ratio configurations (0.05, 0.5, and 1.0 wt %) of COOH-MWCNTs were considered and compared with neat epoxy and ethanol-treated epoxy to investigate the effects of nano enrichment and processing. Here, the thermal properties of the epoxy polymers, including curing kinetics, thermal conductivity, and degradation kinetics were studied. Introducing the MWCNTs increased the curing activation energy as revealed by differential scanning calorimetry. The final thermal conductivity of the 0.5 and 1.0 wt % MWCNT-enriched epoxy samples measured by laser flash technique increased by up to 15% compared with the neat material. The activation energy of the degradation process, investigated by thermogravimetric analysis, was found to increase with increasing CNT content, suggesting that the addition of MWCNTs improved the thermal stability of the epoxy polymers. © 2013 Wiley Periodicals, Inc.

Use of lignite fly ash as an additive in alkaline stabilisation and pasteurisation of wastewater sludge

Energy Technology Data Exchange (ETDEWEB)

Kocaer, F.O.; Alkan, U.; Baskaya, H.S. [Uludag University, Bursa (Turkey). Faculty of Engineering & Architecture

2003-10-01

The possibility of using lignite fly ash in low doses for reducing the pathogen levels in wastewater sludge was investigated. The results showed that using fly ash alone in doses of 40%,80% and 120% (on a dry weight basis), did not produce an alkaline environment for an efficient removal of pathogens. However, using fly ash in conjunction with the minimum amount of quicklime may act as an effective way of fecal coliform removal in both alkaline stabilisation and pasteurisation processes. It was shown that using fly ash in doses of 80% and 120% in alkaline stabilisation and pasteurisation processes prevented the pH decays and regrowth of pathogens during 60 days of storage period. The results of the study confirmed that alkaline pasteurisation process produces a product which is more resistant to pH decays and regrowth of fecal coliforms compared to that of alkaline stabilisation. Consequently, the overall results of this study indicated that the minimum lime and fly ash dosages required to generate a Class B biosolid were 10-15% and 80%, respectively. On the other hand, heating sludge to 50{degree}C prior to the addition of 10-15% quicklime and 80% fly ash followed by further heating to 70{degree}C and then sustaining at this temperature for 30 minutes were sufficient to generate a Class A biosolid.

Glucose-Treated Manganese Hexacyanoferrate for Sodium-Ion Secondary Battery

Directory of Open Access Journals (Sweden)

Yutaka Moritomo

2015-09-01

Full Text Available Manganese hexacyanoferrate (Mn-PBA is a promising cathode material forsodium-ion secondary battery (SIB with high average voltage (=3.4 V against Na. Here,we find that the thermal decomposition of glucose modifies the surface state of Mn-PBA,without affecting the bulk crystal structure. The glucose treatment significantly improves therate properties of Mn-PBA in SIB. The critical discharge rate increases from 1 C (as-grownto 15 C (glucose-treated. Our observation suggests that thermal treatment is quite effectivefor insulating coordination polymers.

Oxidation and thermal shock behavior of thermal barrier coated 18/10CrNi alloy with coating modifications

Energy Technology Data Exchange (ETDEWEB)

Guergen, Selim [Vocational School of Transportation, Anadolu University, Eskisehir (Turkmenistan); Diltemiz, Seyid Fehmi [Turkish Air Force1st Air Supply and Maintenance Center Command, Eskisehir (Turkmenistan); Kushan, Melih Cemal [Dept. of Mechanical Engineering, Eskisehir Osmangazi University, Eskisehir (Turkmenistan)

2017-01-15

In this study, substrates of 18/10CrNi alloy plates were initially sprayed with a Ni-21Cr-10Al-1Y bond coat and then with an yttria stabilized zirconia top coat by plasma spraying. Subsequently, plasma-sprayed Thermal barrier coatings (TBCs) were treated with two different modification methods, namely, vacuum heat treatment and laser glazing. The effects of modifications on the oxidation and thermal shock behavior of the coatings were evaluated. The effect of coat thickness on the bond strength of the coats was also investigated. Results showed enhancement of the oxidation resistance and thermal shock resistance of TBCs following modifications. Although vacuum heat treatment and laser glazing exhibited comparable results as per oxidation resistance, the former generated the best improvement in the thermal shock resistance of the TBCs. Bond strength also decreased as coat thickness increased.

Loss and thermal model for power semiconductors including device rating information

DEFF Research Database (Denmark)

Ma, Ke; Bahman, Amir Sajjad; Beczkowski, Szymon

2014-01-01

The electrical loading and device rating are both important factors that determine the loss and thermal behaviors of power semiconductor devices. In the existing loss and thermal models, only the electrical loadings are focused and treated as design variables, while the device rating is normally...

Thermally treated polyaniline/polybenzimidazole blend membranes: structural changes and gas transport properties

Czech Academy of Sciences Publication Activity Database

Giel, Verena; Morávková, Zuzana; Peter, Jakub; Trchová, Miroslava

2017-01-01

Roč. 537, 1 September (2017), s. 315-322 ISSN 0376-7388 R&D Projects: GA MŠk(CZ) LO1507; GA ČR(CZ) GA16-02787S Institutional support: RVO:61389013 Keywords : polybenzimidazole * polyaniline * thermal treatment Subject RIV: CD - Macromolecular Chemistry OBOR OECD: Polymer science Impact factor: 6.035, year: 2016