WorldWideScience

Sample records for thermal stability ph

  1. Thermal and pH stabilities of partially purified polyphenol oxidase ...

    African Journals Online (AJOL)

    Enzyme activity depends largely on environmental conditions such as temperature and pH. The stability of polyphenol oxidase (PPO) extracted from Solanum melongenas and Musa sapientum fruits preincubated in varying thermal and pH conditions were carried out. Enzyme activity was measured by spectrophotometric ...

  2. Thermal stability of Trichoderma reesei c30 cellulase and aspergillus niger; -glucosidase after ph and chemical modification

    Energy Technology Data Exchange (ETDEWEB)

    Woodward, J.; Whaley, K.S.; Zachry, G.S.; Wohlpart, D.L.

    1981-01-01

    Treatment of Trichoderma reesei C30 cellulase at pH 10.0 for 1 h at room temperature increased its pH and thermal stability. Chemical modification of the free epsilon-amino groups of cellulase at pH 10.0 resulted in no further increase in stability. Such chemical modification, however, decreased the thermal stability of the cellulose-cellulase complex. On the contrary, the chemical modification of Aspergillus niger glucosidase with glutaraldehyde at pH 8.0 increased the thermal stability of this enzyme.

  3. Thermal stability of Trichoderma reesei C30 cellulase and Aspergillus niger. beta. -glucosidase after pH and chemical modification

    Energy Technology Data Exchange (ETDEWEB)

    Woodward, J.; Whaley, K.S.; Zachry, G.S.; Wohlpart, D.L.

    1981-01-01

    Treatment of Trichoderma reesei C30 cellulase at pH 10.0 for 1 h at room temperature increased its pH and thermal stability. Chemical modification of the free epsilon-amino groups of cellulase at pH 10.0 resulted in no further increase in stability. Such chemical modification, however, decreased the thermal stability of the cellulose-cellulase complex. On the contrary, the chemical modification of Aspergillus niger ..beta..-glucosidase with glutaraldehyde at pH 8.0 increased the thermal stability of this enzyme.

  4. Potential phosphorus eutrophication mitigation strategy: Biochar carbon composition, thermal stability and pH influence phosphorus sorption

    Science.gov (United States)

    L.W. Ngatia; Y.P. Hsieh; D. Nemours; R. Fu; R.W. Taylor

    2017-01-01

    Phosphorus (P) eutrophication is a major pollution problem globally, with unprecedented amount of P emanating from agricultural sources. But little is known about the optimization of soil-biochar P sorption capacity. The study objective was to determine how biochar feedstocks and pyrolysis conditions influences carbon (C) thermal stability, C composition and pH and in...

  5. Evaluation of the pH and thermal stabilities of rosella anthocyanin extracts under solar light

    Directory of Open Access Journals (Sweden)

    Kahtan A. Askar

    2015-09-01

    Full Text Available Anthocyanin is considered as an unstable pigment, undergoes gradual degradation processes throughout the storage or use. The degradation of Rosella anthocyanin extract (RAE in different pH solutions was studied under solar light and compared with solutions kept in the dark. It appears that RAE solutions under solar light were suffering rapid degradation than those kept in the dark. Moreover, RAE samples at higher pH values showed faster rates of degradation than those with lower pH values. A mechanism for degradation was suggested through the formation of hydroxyl radical which is responsible for demineralization process. It is also appears that as the initial concentration of the dye increases, the requirement needed for degradation increased as well. The thermal degradation behavior of RAE at temperature range 25–60 °C under solar light showed first order kinetics with low activation energies.

  6. Potential phosphorus eutrophication mitigation strategy: Biochar carbon composition, thermal stability and pH influence phosphorus sorption.

    Science.gov (United States)

    Ngatia, L W; Hsieh, Y P; Nemours, D; Fu, R; Taylor, R W

    2017-08-01

    Phosphorus (P) eutrophication is a major pollution problem globally, with unprecedented amount of P emanating from agricultural sources. But little is known about the optimization of soil-biochar P sorption capacity. The study objective was to determine how biochar feedstocks and pyrolysis conditions influences carbon (C) thermal stability, C composition and pH and in turn influence the phosphorus sorption optimization. Biochar was produced from switchgrass, kudzu and Chinese tallow at 200, 300, 400, 500, 550, 650,750 °C. Carbon thermal stability was determined by multi-element scanning thermal analysis (MESTA), C composition was determined using solid state 13 C NMR. Phosphorus sorption was determined using a mixture of 10% biochar and 90% sandy soil after incubation. Results indicate increased P sorption (P biochar pyrolysis temperature. However, optimum P sorption was feedstock specific with switchgrass indicating P desorption between 200 and 550 °C. Phosphorus sorption was in the order of kudzu > switchgrass > Chinese tallow. Total C, C thermal stability, aromatic C and alkalinity increased with elevated pyrolysis temperature. Biochar alkalinity favored P sorption. There was a positive relationship between high thermal stable C and P sorption for Kudzu (r = 0.62; P = 0.0346) and Chinese tallow (r = 0.73; P = 0.0138). In conclusion, biochar has potential for P eutrophication mitigation, however, optimum biochar pyrolysis temperature for P sorption is feedstock specific and in some cases might be out of 300-500 °C temperature range commonly used for agronomic application. High thermal stable C dominated by aromatic C and alkaline pH seem to favor P sorption. Copyright © 2017 Elsevier Ltd. All rights reserved.

  7. Microencapsulation of butyl stearate with melamine-formaldehyde resin: Effect of decreasing the pH value on the composition and thermal stability of microcapsules

    Directory of Open Access Journals (Sweden)

    M. Krajnc

    2012-10-01

    Full Text Available The object of this study was to investigate how different decreasing of pH regimes during microencapsulation process with melamine-formaldehyde (MF resin affects the composition, morphology and thermal stability of microcapsules containing a phase-change material (PCM. Technical butyl stearate was used as PCM. Microencapsulation was carried out at 70°C. For all experiments the starting pH value was 6.0. After one hour of microencapsulation at the starting pH value, the pH value was lowered to final pH value (5.5; 5.0; 4.5 in a stepwise or linear way. The properties of microcapsules were monitored during and after the microencapsulation process. The results showed that pH value decreasing regime was critical for the morphology and stability of microcapsules. During microencapsulations with a stepwise decrease of pH value we observed faster increase of the amount of MF resin in the microencapsulation product compared to the microencapsulations with a linear pH value decrease. However, faster deposition in the case of microencapsulations with stepwise decrease of pH value did not result in thicker MF shells. The shell thickness increased much faster when the pH value was decreased in a linear way or in several smaller steps. It was shown that for the best thermal stability of microcapsules, the pH value during microencapsulation had to be lowered in a linear way or in smaller steps to 5.0 or lower.

  8. Thermal Stabilization Blend Plan

    Energy Technology Data Exchange (ETDEWEB)

    RISENMAY, H.R.

    2000-05-02

    This Blend Plan documents the feed material items that are stored in 2736-2 vaults, the 2736-ZB 638 cage, the 192C vault, and the 225 vault that will be processed through the thermal stabilization furnaces. The purpose of thermal stabilization is to heat the material to 1000 degrees Celsius to drive off all water and leave the plutonium and/or uranium as oxides. The stabilized material will be sampled to determine the Loss On Ignition (LOI) or percent water. The stabilized material must meet water content or LOI of less than 0.5% to be acceptable for storage under DOE-STD-3013-99 specifications. Out of specification material will be recycled through the furnaces until the water or LOI limits are met.

  9. Dispersion stability of thermal nanofluids

    Directory of Open Access Journals (Sweden)

    Fan Yu

    2017-10-01

    Full Text Available Thermal nanofluids, the engineered fluids with dispersed functional nanoparticles, have exhibited extraordinary thermophysical properties and added functionalities, and thus have enabled a broad range of important applications. The poor dispersion stability of thermal nanofluids, however, has been considered as a long-existing issue that limits their further development and practical application. This review overviews the recent efforts and progresses in improving the dispersion stability of thermal nanofluids such as mechanistic understanding of dispersion behavior of nanofluids, examples of both water-based and oil-based nanofluids, strategies to stabilize nanofluids, and characterization techniques for dispersion behavior of nanofluids. Finally, on-going research needs, and possible solutions to research challenges and future research directions in exploring stably dispersed thermal nanofluids are discussed. Keywords: Thermal nanofluids, Dispersion, Aggregation, Electrostatic stabilization, Steric stabilization

  10. Stabilized thermally compensated mirror

    International Nuclear Information System (INIS)

    Dunn, C. III; Tobin, R.D.; Bergstreser, N.E.; Heinz, T.A.

    1975-01-01

    A thermally compensated mirror is described that is formed by a laminated structure. The structure is comprised of a front plate having a reflective front surface and having a plurality of grooves formed in the rear surface for conducting coolant fluid in heat exchanging relation with said reflective surface, a rear plate having coolant inlet and coolant outlet openings extending therethrough, a minimum temperature plate interposed between said front and rear plates and formed with a plurality of coolant distribution passageways coupled to receive coolant fluid from said coolant inlet and oriented to distribute said coolant fluid in a manner to establish a minimum temperature plane parallel to said reflective surface, a temperature stabilization plate interposed between said front plate and said minimum temperature plate and formed with a plurality of coolant distribution channels coupled to receive said coolant fluid after said coolant fluid has passed in heat exchanging relation with said reflective surface and oriented to distribute said coolant fluid in a manner to establish a uniform temperature plane parallel to said reflective surface, and means for circulating said coolant fluid through said structure in a predetermined path. (U.S.)

  11. Expression in Escherichia coli of cysteine protease inhibitors from cowpea (Vigna unguiculata): The crystal structure of a single-domain cystatin gives insights on its thermal and pH stability.

    Science.gov (United States)

    Monteiro Júnior, José Edvar; Valadares, Napoleão Fonseca; Pereira, Humberto D'Muniz; Dyszy, Fábio Henrique; da Costa Filho, Antônio José; Uchôa, Adriana Ferreira; de Oliveira, Adeliana Silva; da Silveira Carvalho, Cristina Paiva; Grangeiro, Thalles Barbosa

    2017-09-01

    Two cysteine proteinase inhibitors from cowpea, VuCys1 and VuCys2, were produced in E. coli ArcticExpress (DE3). The recombinant products strongly inhibited papain and chymopapain as well as the midgut proteases from Callosobruchus maculatus larvae, a bruchid that uses cysteine proteases as major digestive enzymes. Heat treatment at 100°C for up to 60min or incubation at various pH values caused little reduction in the papain inhibitory activity of both inhibitors. Moreover, minor conformational variations, as probed by circular dichroism spectroscopy, were observed after VuCys1 and VuCys2 were subjected to these treatments. The crystal structure of VuCys1 was determined at a resolution of 1.95Å, revealing a domain-swapped dimer in the asymmetric unit. However, the two lobes of the domain-swapped dimer are positioned closer to each other in VuCys1 in comparison to other similar cystatin structures. Moreover, some polar residues from opposite lobes recruit water molecules, forming a hydrogen bond network that mediates contacts between the lobes, thus generating an extended open interface. Due to the closer distance between the lobes, a small hydrophobic core is also formed, further stabilizing the folded domain-swapped dimer. These structural features might account for the extraordinary thermal and pH stability of VuCys1. Copyright © 2017 Elsevier B.V. All rights reserved.

  12. Chemical and thermal stability of insulin

    DEFF Research Database (Denmark)

    Huus, Kasper; Havelund, Svend; Olsen, Helle B

    2006-01-01

    To study the correlation between the thermal and chemical stability of insulin formulations with various insulin hexamer ligands.......To study the correlation between the thermal and chemical stability of insulin formulations with various insulin hexamer ligands....

  13. Stabilization of Mercury in High pH Tank Sludges

    Energy Technology Data Exchange (ETDEWEB)

    Spence, R.; Barton, J.

    2003-02-24

    DOE complex contains many tank sludges contaminated with mercury. The high pH of these tank sludges typically fails to stabilize the mercury, resulting in these radioactive wastes also being characteristically hazardous or mixed waste. The traditional treatment for soluble inorganic mercury species is precipitation as insoluble mercuric sulfide. Sulfide treatment and a commercial mercury-stabilizing product were tested on surrogate sludges at various alkaline pH values. Neither the sulfide nor the commercial product stabilized the mercury sufficiently at the high pH of the tank sludges to pass the Toxicity Characteristic Leach Procedure (TCLP) treatment standards of the Resource Conservation and Recovery Act (RCRA). The commercial product also failed to stabilize the mercury in samples of the actual tank sludges.

  14. Control for fusion thermal stability

    International Nuclear Information System (INIS)

    Maya, I.; Campbell, H.D.

    1983-01-01

    An analysis of the thermal balance of a fusioning plasma from a control system perspective has been performed. The requirements for stability and the response characteristics of the thermal balance have been evaluated. The results show that open-loop equilibria are characterized by restrictively narrow stable operating temperature regimes and generally poor system performance. Closed-loop proportional feedback using the fuel feedrate and injection energy can be used to extend the stable operating temperature regime and significantly improve the system response. Thus, high open-loop temperature overshoots without neutral beam injection can be reduced to acceptable levels at temperature overshoots without neutral beam injection can be reduced to acceptable levels at temperatures as low as 20 keV, with a decrease in the settling time to under 30 sec. With 75 keV injection energy, acceptable overshoot can be obtained at plasma temperatures as low as 10 keV, with the time-to-peak below 20 sec and settling times less than 30 sec. It is still difficult to simultaneously satisfy overshoot and speed of response requirements at low temperatures with low feedback fractions. Additional improvement is available using proportional-integral-derivative (PID) control

  15. Optimum pH and pH Stability of Crude Polyphenol Oxidase (PPO ...

    African Journals Online (AJOL)

    The effect of pH on the activity and stability of crude polyphenol oxidase (PPO) extracted from garden egg (Solanum aethiopicum), pawpaw (Carica papaya), pumpkin ... Optimum pH values were found to be 6.0,6.5,6.0, 4.5 and 4.0/or 8.0 for the enzyme extracted from Solanum aethiopicum, Carica papaya, Cucurbita pepo, ...

  16. Thermal stability of PMMA–clay hybrids

    Indian Academy of Sciences (India)

    Administrator

    are then polymerized with poly methyl methacrylate (PMMA) by solution intercalation method. The thermal stability of these different clay–PMMA hybrids have been ... Dispersants; DSC; exfoliation; hybrid; nanoclay; poly (methyl methacrylate); SEM; thermal sta- .... drop of clove oil was added to the naturally dispersed clay.

  17. Thermal stability of phosphate coatings on steel

    Directory of Open Access Journals (Sweden)

    P. Pokorny

    2015-07-01

    Full Text Available The work was validated thermal stability of zinc, manganese and tri-cations phosphate coatings on steel, made from commercial phosphating bath type Pragofos. Thermogravimetric data dehydration of scholzite, phosphophylite and hureaulite coatings in the temperature range 160 °C – 400 °C define the conditions for applying paints with higher firing temperature or thermal spraying ceramic coatings.

  18. Thermal hydraulic stability experiments in rod bundle

    International Nuclear Information System (INIS)

    Enomoto, T.; Muto, S.; Ishizuka, T.; Tanabe, A.; Mitsutake, T.; Sakurai, M.

    1985-01-01

    Thermal hydraulic stability tests have been performed on electrically heated bundles to simulate Boiling Water Reactor (BWR) fuels in a parallel channel test-loop. The test facility used is for the study of the steady state and transient characteristics of various thermal hydraulic conditions encountered in BWR operation, such as flow- high power operation, abnormal transient conditions and post boiling transition, including thermal hydraulic stability. Moreover, steady state and transient void behavior can be measured using an additional test section for this facility

  19. Thermal Stabilization of Biologics with Photoresponsive Hydrogels.

    Science.gov (United States)

    Sridhar, Balaji V; Janczy, John R; Hatlevik, Øyvind; Wolfson, Gabriel; Anseth, Kristi S; Tibbitt, Mark W

    2018-03-12

    Modern medicine, biological research, and clinical diagnostics depend on the reliable supply and storage of complex biomolecules. However, biomolecules are inherently susceptible to thermal stress and the global distribution of value-added biologics, including vaccines, biotherapeutics, and Research Use Only (RUO) proteins, requires an integrated cold chain from point of manufacture to point of use. To mitigate reliance on the cold chain, formulations have been engineered to protect biologics from thermal stress, including materials-based strategies that impart thermal stability via direct encapsulation of the molecule. While direct encapsulation has demonstrated pronounced stabilization of proteins and complex biological fluids, no solution offers thermal stability while enabling facile and on-demand release from the encapsulating material, a critical feature for broad use. Here we show that direct encapsulation within synthetic, photoresponsive hydrogels protected biologics from thermal stress and afforded user-defined release at the point of use. The poly(ethylene glycol) (PEG)-based hydrogel was formed via a bioorthogonal, click reaction in the presence of biologics without impact on biologic activity. Cleavage of the installed photolabile moiety enabled subsequent dissolution of the network with light and release of the encapsulated biologic. Hydrogel encapsulation improved stability for encapsulated enzymes commonly used in molecular biology (β-galactosidase, alkaline phosphatase, and T4 DNA ligase) following thermal stress. β-galactosidase and alkaline phosphatase were stabilized for 4 weeks at temperatures up to 60 °C, and for 60 min at 85 °C for alkaline phosphatase. T4 DNA ligase, which loses activity rapidly at moderately elevated temperatures, was protected during thermal stress of 40 °C for 24 h and 60 °C for 30 min. These data demonstrate a general method to employ reversible polymer networks as robust excipients for thermal stability of complex

  20. Research of thermal stability of ion exchangers

    International Nuclear Information System (INIS)

    Stuchlik, S.; Srnkova, J.

    1983-01-01

    Prior to the fixation of radioactive ion exchangers into bitumen these exchangers have to be dried. The resulting gaseous products may generate explosive mixtures. An analysis was made of the thermal stability of two types of ion exchangers, the cation exchanger KU-2-8 cS and the anion exchanger AV-17-8 cS which are used in the V-1 nuclear power plant at Jaslovske Bohunice. The thermal stability of the anion exchangers was monitored using gas chromatography at temperatures of 100, 120, 140, 160 and 180 degC and by measuring weight loss by kiln-drying at temperatures of 120, 140, 160 and 180 degC. The ion exchanger was heated for 6 hours and samples were taken continuously at one hour intervals. The thermal stability of the cation exchanger was monitored by measuring the weight loss. Gas chromatography showed the release of trimethylamine from the anion exchanger in direct dependence on temperature. The measurement of weight losses, however, only showed higher losses of released products which are explained by the release of other thermally unstable products. The analysis of the thermal stability of the cation exchanger showed the release of SO 2 and the weight loss (following correction for water content) was found only after the fourth hour of decomposition. The experiment showed that the drying of anion exchanger AV-17-8 cS may cause the formation of explosive mixtures. (J.P.)

  1. Thermal stability engineering of Glomerella cingulata cutinase.

    Science.gov (United States)

    Chin, Iuan-Sheau; Abdul Murad, Abdul Munir; Mahadi, Nor Muhammad; Nathan, Sheila; Abu Bakar, Farah Diba

    2013-05-01

    Cutinase has been ascertained as a biocatalyst for biotechnological and industrial bioprocesses. The Glomerella cingulata cutinase was genetically modified to enhance its enzymatic performance to fulfill industrial requirements. Two sites were selected for mutagenesis with the aim of altering the surface electrostatics as well as removing a potentially deamidation-prone asparagine residue. The N177D cutinase variant was affirmed to be more resilient to temperature increase with a 2.7-fold increase in half-life at 50°C as compared with wild-type enzyme, while, the activity at 25°C is not compromised. Furthermore, the increase in thermal tolerance of this variant is accompanied by an increase in optimal temperature. Another variant, the L172K, however, exhibited higher enzymatic performance towards phenyl ester substrates of longer carbon chain length, yet its thermal stability is inversely affected. In order to restore the thermal stability of L172K, we constructed a L172K/N177D double variant and showed that these two mutations yield an improved variant with enhanced activity towards phenyl ester substrates and enhanced thermal stability. Taken together, our study may provide valuable information for enhancing catalytic performance and thermal stability in future engineering endeavors.

  2. Thermal characteristics of yttria stabilized zirconia nanolubricants

    Directory of Open Access Journals (Sweden)

    Sakthinathan Ganapathy

    2012-01-01

    Full Text Available The transition from microparticles to nanoparticles can lead to a number of changes in its properties. The objective of this work is to analyze the thermal, tribological properties of yttria stabilized zirconia nanoparticles. Nanosized yttria stabilized zir conia particles were prepared by milling the yttria stabilized zirconia (10 ftm in a planetary ball mill equipped with vials using tungsten carbide balls. After 40 hours milled the yttria stabilized zirconia nanoparticles of sizes ranging from 70-90 nm were obtained. The phase composition and morphologies of the assynthesized particles were characterized by energy dispersive X-ray analysis, scanning electron microscope, transmission electron microscope, thermogravimetric analysis and differential scanning calorimeter, and the images of the same were obtained. From TG-DSC analysis it was confirmed that, the yttria stabilized zirconia nanoparticles were heat stable under different thermal conditions which is due to the addition of yttria to pure zirconia. Due to this property of yttria stabilized zirconia nanoparticles, it can be widely used in high transfer application such as lubricant additives. The heat transfer properties of automotive engine lubricants were determined by utilization of measured thermal conductivity, viscosity index, density, flash point, fire point and pour point revealed that lubricants with additive constituents have a significant effect on the resultant heat transfer characteristics of the lubricants.

  3. Structure and thermal stability of nanocrystalline materials

    Indian Academy of Sciences (India)

    In addition, study of the thermal stability of nanocrystalline materials against significant grain growth is both scientific and technological interest. A sharp increase in grain size (to micron levels) during consolidation of nanocrystalline powders to obtain fully dense materials may consequently result in the loss of some unique ...

  4. Multifunctional Composites for Improved Polyimide Thermal Stability

    Science.gov (United States)

    Miller, Sandi G.

    2007-01-01

    The layered morphology of silicate clay provides an effective barrier to oxidative degradation of the matrix resin. However, as resin thermal stability continues to reach higher limits, development of an organic modification with comparable temperature capabilities becomes a challenge. Typically, phyllosilicates used in polymer nanocomposites are modified with an alkyl ammonium ion. Such organic modifiers are not suited for incorporation into high temperature polymers as they commonly degrade below 200oC. Therefore, the development of nanoparticle specifically suited for high temperature applications is necessary. Several nanoparticles were investigated in this study, including pre-exfoliated synthetic clay, an organically modified clay, and carbon nanofiber. Dispersion of the layered silicate increases the onset temperature of matrix degradation as well as slows oxidative degradation. The thermally stable carbon nanofibers are also observed to significantly increase the resin thermal stability.

  5. Improvement of Thermal Stability of BCG Vaccine

    Science.gov (United States)

    Jahanbakhsh Sefidi, Fatemeh; Kaghazian, Homan; Moradli, Gholam Ali; Hassanzadeh, Seyed Mehdi

    2017-11-01

    Thermal stability (TS) is a part of the BCG vaccine characterization by which the consistency of process in BCG vaccine production could be confirmed. To enhance the TS of the vaccine, some prevalent stabilizers in different concentrations were added to the final formulation of BCG bulk prior to Freeze-drying process. We found a formulation more effective than the current stabilizer for retaining the higher viability of lyophilized BCG vaccine produced by Pasteur Institute of Iran. In the design of experiments using Taguchi method, lactose, trehalose, glucose, dextran, and monosodium glutamate were added to the final formulation of BCG bulk prior to freeze-drying process. Viability of the samples was determined by counting the colony forming unit. Maximum signal-to-noise ratio equal to maximum TS and viability was obtained by adding lactose, dextran, and glutamate in defined concentrations. Adding the stabilizers had a significant impact on TS of BCG vaccine to meet the quality requirements.

  6. Thermal stability of tunneling spin polarization

    International Nuclear Information System (INIS)

    Kant, C.H.; Kohlhepp, J.T.; Paluskar, P.V.; Swagten, H.J.M.; Jonge, W.J.M. de

    2005-01-01

    We present a study of the thermal stability of tunneling spin polarization in Al/AlOx/ferromagnet junctions based on the spin-polarized tunneling technique, in which the Zeeman-split superconducting density of states in the Al electrode is used as a detector for the spin polarization. Thermal robustness of the polarization, which is of key importance for the performance of magnetic tunnel junction devices, is demonstrated for post-deposition anneal temperatures up to 500 o C with Co and Co 90 Fe 10 top electrodes, independent of the presence of an FeMn layer on top of the ferromagnet

  7. System Design Description PFP Thermal Stabilization

    International Nuclear Information System (INIS)

    RISENMAY, H.R.

    2000-01-01

    The purpose of this document is to provide a system design description (SDD) and design basis for the Plutonium Finishing Plant (PFP) Thermal Stabilization project. The chief objective of the SDD is to document the Structures, Systems, and Components (SSCs) that establish and maintain the facility Safety Envelope necessary for normal safe operation of the facility; as identified in the FSAR, the OSRs, and Safety Assessment Documents (SADs). This safety equipment documentation should satisfy guidelines for the SDD given in WHC-SD-CP-TI-18 1, Criteria for Identification and Control of Equipment Necessary for Preservation of the Safety Envelope and Safe Operation of PFP. The basis for operational, alarm response, maintenance, and surveillance procedures are also identified and justified in this document. This document and its appendices address the following elements of the PFP Thermal Stabilization project: Functional and design requirements; Design description; Safety Envelope Analysis; Safety Equipment Class; and Operational, maintenance and surveillance procedures

  8. The pH-dependent thermal and storage stability of glycosylated caseinomacropeptide

    DEFF Research Database (Denmark)

    Siegert, Nadja; Tolkach, Alexander; Kulozik, Ulrich

    2012-01-01

    treatment and storage under different pH values. Process stability (preservation of native protein structure in terms of attached glycans) was analysed by quantifying the release of the terminal carbohydrate, N-acetylneuraminic acid (Neu5Ac), from gCMP. The results clearly showed that the thermal stability...... of gCMP is strongly influenced by pH. When the pH was decreased from 7 to 2, reduced stability was found even at low heating temperatures. Minimal destabilisation effects were found at neutral pH. Similar observations were found during storage of gCMP. Neu5Ac was released after six days of storage......, with a maximum release of 30% at pH 2. Acidic pH conditions were responsible for the hydrolysis of the glycans from the peptide backbone during heat treatment and storage....

  9. Thermal stability of soy-based polyurethanes

    Directory of Open Access Journals (Sweden)

    Luciane L. Monteavaro

    2005-06-01

    Full Text Available New types of polyurethanes were prepared by reacting diisocyanates and formiated soy polyols with different OH functionalities. Thermal properties and degradation kinetics were investigated by TGA. All prepared PU's showed at least two-weight loss steps, the first one, around 210 °C. Thermal stability of these PUs depends strongly on urethane groups per unit volume and an increase in the weight loss was observed as a result of the increased amount of urethane groups. Degradation kinetics behavior of the soy-based polyurethanes was investigated according to the Flynn method. Different average activation energy values were obtained from isothermal and isoconversional curves, 140.6 KJ/mol and 62.8 KJ/mol, respectively, indicating the complexity of the PUs degradation process.

  10. Thermal stability of gallium arsenide solar cells

    Science.gov (United States)

    Papež, Nikola; Škvarenina, Ľubomír.; Tofel, Pavel; Sobola, Dinara

    2017-12-01

    This article summarizes a measurement of gallium arsenide (GaAs) solar cells during their thermal processing. These solar cells compared to standard silicon cells have better efficiency and high thermal stability. However, their use is partly limited due to high acquisition costs. For these reasons, GaAs cells are deployed only in the most demanding applications where their features are needed, such as space applications. In this work, GaAs solar cells were studied in a high temperature range within 30-650 °C where their functionality and changes in surface topology were monitored. These changes were recorded using an electron microscope which determined the position of the defects; using an atomic force microscope we determined the roughness of the surface and an infrared camera that showed us the thermal radiated places of the defected parts of the cell. The electrical characteristics of the cells during processing were determined by its current-voltage characteristics. Despite the occurrence of subtle changes on the solar cell with newly created surface features after 300 °C thermal processing, its current-voltage characteristic remained without a significant change.

  11. Influence of microenvironment pH, humidity, and temperature on the stability of polymorphic and amorphous forms of clopidogrel bisulfate

    DEFF Research Database (Denmark)

    Raijada, Dhara K; Singh, Saranjit; Bansal, Arvind K

    2010-01-01

    The effect of microenvironment pH, humidity, and temperature was evaluated on the stability of polymorphic and amorphous forms of clopidogrel bisulfate, when present alone or in combinations. Oxalic acid and sodium carbonate were used as solid stressors to create acidic and alkaline pH, respectiv......The effect of microenvironment pH, humidity, and temperature was evaluated on the stability of polymorphic and amorphous forms of clopidogrel bisulfate, when present alone or in combinations. Oxalic acid and sodium carbonate were used as solid stressors to create acidic and alkaline p...... salt to free base. Thermal studies indicated that polymorphic forms of clopidogrel bisulfate and also its glassy amorphous form were highly resistant to temperature, whereas the rubbery state of the drug degraded significantly at temperatures of > or =80 degrees C....

  12. Thermal stability of rare earth oxychlorides

    Energy Technology Data Exchange (ETDEWEB)

    Bunda, V.V.; Shtilikha, M.V.; Golovej, V.M. (Uzhgorodskij Gosudarstvennyj Univ. (Ukrainian SSR))

    1984-12-01

    The thermal stability of oxychlorides of the lanthanum series is investigated to determine the possibility of preparing them in the form of crystals by the method of l chemical gas-transport reactions (CTR). The lanthanide oxychlorides were subjected to thermogravimetric studies in the 20-1500 deg C temperature range under normal conditions. The temperatures of initiation of incongruent decomposition reactions are found. It is found that the process of LnOCl decomposition is preceeded by the exothermal effect connected with the Ln/sub 2/OCl/sub 4/ recrystallization to LnOCl. The thermodynamic and kinetic parameters of decomposition reactions are determined, such as reaction heats ..delta..H, decomposition rate constants K, dissociation energies E, reaction orders n. The LnOCl specific heats (Csub(P))sub(T) are estimated. It is shown that the LnOCl compounds can be prepared in the form of monocrystals by the CTR method.

  13. Thermal stability of nanoscale metallic multilayers

    Energy Technology Data Exchange (ETDEWEB)

    Ramos, A.S., E-mail: sofia.ramos@dem.uc.pt [CEMUC, Departamento de Engenharia Mecânica, Universidade de Coimbra, 3030-788 Coimbra (Portugal); Cavaleiro, A.J.; Vieira, M.T. [CEMUC, Departamento de Engenharia Mecânica, Universidade de Coimbra, 3030-788 Coimbra (Portugal); Morgiel, J. [Institute of Metallurgy and Materials Science, Polish Academy of Sciences, Reymonta 25, 30-059 Cracow (Poland); Safran, G. [Research Institute for Technical Physics and Materials Science, Hungarian Academy of Sciences, H-1121 Budapest (Hungary)

    2014-11-28

    Metallic nanolayered thin films/foils, in particular Ni/Al multilayers, have been used to promote joining. The objective of this work is to evaluate the thermal stability of nanoscale metallic multilayers with potential for joining applications. Multilayers thin films with low (Ti/Al and Ni/Ti), medium (Ni/Al) and high (Pd/Al) enthalpies of exothermic reaction were prepared by dual cathode magnetron sputtering. Their thermal stability was studied by: i) differential scanning calorimetry combined with X-ray diffraction (XRD), ii) in-situ XRD using cobalt radiation, and iii) in-situ transmission electron microscopy. It was possible to detect traces of intermetallic or amorphous phases in the as-deposited short period (bilayer thickness) multilayers, except for the Ti/Al films where no reaction products that might be formed during deposition were identified. For short periods (below 20 nm) the equilibrium phases are directly achieved upon annealing, whereas for higher periods intermediate trialuminide phases are present for Ti/Al and Ni/Al multilayers. The formation of B2-NiTi from Ni/Ti multilayers occurs without the formation of intermediate phases. On the contrary, for the Pd–Al system the formation of intermediate phases was never avoided. The viability of nanoscale multilayers as “filler” materials for joining macro or microparts/devices was demonstrated. - Highlights: • Me1 and Me2 (Me—metal) alternated nanolayers deposited by magnetron sputtering • Reactive Me1/Me2 multilayer thin films with nanometric modulation period • By heat treatment the films always evolve to the equilibrium intermetallic phase. • For some Me1–Me2 systems and periods, the formation of intermediate phases occurs. • Me1/Me2 multilayer thin films can be used as filler materials to enhance joining.

  14. Thermal stability of gold-PS nanocomposites thin films

    Indian Academy of Sciences (India)

    Administrator

    an improved thermal stability of the polystyrene (PS) composite film much above its glass transition tempera- ture. Keywords. Thermal stability; polymer nanocomposites; low temperature .... The color of the solution changed immediately from pale yellow to black upon the addition. The reaction mix- ture was stirred for 2 h ...

  15. System Design Description PFP Thermal Stabilization

    Energy Technology Data Exchange (ETDEWEB)

    RISENMAY, H.R.

    2000-01-27

    DOE has authorized in their letter of August 2, 1999, the operation of these three furnaces, quote ''Operation of the three uncompleted muffle furnaces (No.3, No.4, and No.5) located in Room 235B is authorized, using the same feed charge limits as the two existing furnaces (No.1, and No.2) located in Room 230C,''. The above statement incorrectly refers to Room 230C whereas the correct location is Room 230A. The current effort is directed to initiate the operation and to complete the design activities DOE authorized the operation of the furnaces based on their Safety Evaluation Report (SER). Based on analogy and the principle of similarity, the risks and consequences of accidents both onsite and offsite due to operation of three furnaces are not significantly larger than those already evaluated with the two operating furnaces. Thermal stabilization operations and the material of feed for furnaces in Glovebox HA-21 I are essentially the same as those currently being stabilized in furnaces in Glovebox HC-21 C. Therefore the accident analysis has utilized identical accident scenarios in evaluation and no additional failure modes are introduced by HA-21 I muffle furnace operation that would enhance the consequences of accidents. Authorization Basis documents as referenced below (PFP FSAR and DOE Letter authorizing the operation) appear to contradict each other, i.e. one allows and authorizes the operation and the other imposes the restriction on the operation. The purpose of the PFP FSAR restrictions was to review thoroughly the design and installation of three furnaces and perform acceptance testing before approving the startup for operation. With the experience of operating the two furnaces in Glovebox HC-21C, and the knowledge of risks and hazards the facility operation, the plant is adequately prepared to operate these additional furnaces. ECN 653595 has been prepared to incorporate operation of the muffle furnaces in Glovebox HA-21 I into the

  16. Effect of chitosan on the heat stability of whey protein solution as a function of pH.

    Science.gov (United States)

    Zhao, Zhengtao; Xiao, Qian

    2017-03-01

    Chitosan was reported to interact with proteins through electrostatic interactions. Their interaction was influenced by pH, which was not fully characterized. Further research on the interactions between protein and chitosan at different pH and their influence on the thermal denaturation of proteins is necessary. In this research, the effect of chitosan on the heat stability of whey protein solution at pH 4.0-6.0 was studied. At pH 4.0, a small amount chitosan was able to prevent the heat-induced denaturation and aggregation of whey protein molecules. At higher pH values (5.5 and 6.0), whey proteins complexed with chitosan through electrostatic attraction. The formation of chitosan-whey protein complexes at pH 5.5 improved the heat stability of dispersions and no precipitation could be detected up to 20 days. The dispersion with a medium amount of chitosan (chitosan:whey protein 1:5) produced the most stable particles, which had an average radius of 135 ± 14 nm and a zeta potential value of 36 ± 1 mV. In contrast, at pH 6.0 only the dispersion with a high amount of chitosan (chitosan:whey protein 1:2) showed good shelf stability up to 20 days. It was possible to produce heat-stable whey protein beverages by regulating the interaction between chitosan and whey protein molecules. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

  17. Thermal stability and deactivation energy of free and immobilized invertase

    Directory of Open Access Journals (Sweden)

    F.J. Bassetti

    2000-12-01

    Full Text Available The thermal stability and the energy of deactivation of free invertase and the immobilized enzyme (IE was measured at temperatures in the range of 35 to 65°C for the hydrolysis of a 5% w/v sucrose solution. The free enzyme at pH 5.0 is stable up to 50°C for a period of 4 h. Invertase immobilized in controlled pore silica by the silane-glutaraldehyde covalent method is stable up to 55ºC, in pH 4.5 for the same period. For higher temperatures the enzyme deactivation follows the exponential decay model and half-lives are 0.53, 1.80, and 13.9 h for free invertase, at 65, 60, and 55ºC, respectively. For the IE half-lives are 0.48, 1.83, and 20.9 h, at 65, 60, and 55ºC, respectively. The IE is more stable than the free invertase; the energy of deactivation being 83.1 kcal/mol for the IE and 72.0 kcal/mol for the free enzyme.

  18. Thermal stability of the immobilized fructosyltransferase from Rhodotorula sp

    Directory of Open Access Journals (Sweden)

    E Aguiar-Oliveira

    2011-09-01

    Full Text Available The thermal stability of the extracellular fructosyltransferase (FTase from Rhodotorula sp., recovered from cultivation medium by ethanol precipitation and immobilized onto niobium ore, was studied by Arrhenius plot, half - life profile, half - inactivation temperature (T50 and thermodynamic parameters. The Arrhenius plot showed two different behaviors with different deactivation energies (Ead only after immobilization, the transition occurring in the temperature interval between 51 and 52ºC. T50 for the free enzyme was estimated to be around 62ºC and, after immobilization, 66ºC. After 15 minutes at 52ºC, it was also possible to observe enzymatic activation for both the free and immobilized forms, but greater activation was achieved at pH 4.5 with the immobilized enzyme. Between 47 - 51ºC the immobilized enzyme was more stable than the free enzyme, with pH 6.0 being the more stable condition for the immobilized enzyme. However, above 52ºC the free form was more stable.

  19. Determination of thermal diffusivity of cement-stabilized laterite by ...

    African Journals Online (AJOL)

    Knowledge of thermo-physical properties of local building materials are necessary for thermal comfort design and construction of residential accommodation. Thermal diffusivity of cement-stabilized laterites were measured under conditions of transient thermal field and induced surface stress, assuming constant temperature ...

  20. Emulsifier type, metal chelation and pH affect oxidative stability of n-3-enriched emulsions

    DEFF Research Database (Denmark)

    Haahr, Anne-Mette; Jacobsen, Charlotte

    2008-01-01

    -enriched oil-in-water emulsion. The selected food emulsifiers were Tween 80, Citrem, sodium caseinate and lecithin. Lipid oxidation was evaluated by determination of peroxide values and secondary volatile oxidation products. Moreover, the zeta potential and the droplet sizes were determined. Twen resulted...... in the least oxidatively stable emulsions, followed by Citrem. When iron was present, caseinate-stabilized emulsions oxidized slower than lecithin emulsions at pH 3, whereas the opposite was the case at pH 7. Oxidation generally progressed faster at pH 3 than at pH 7, irrespective of the addition of iron. EDTA...

  1. Equilibrium unfolding of A. niger RNase: pH dependence of chemical and thermal denaturation.

    Science.gov (United States)

    Kumar, Gundampati Ravi; Sharma, Anurag; Kumari, Moni; Jagannadham, Medicherla V; Debnath, Mira

    2011-08-01

    Equilibrium unfolding of A. niger RNase with chemical denaturants, for example GuHCl and urea, and thermal unfolding have been studied as a function of pH using fluorescence, far-UV, near-UV, and absorbance spectroscopy. Because of their ability to affect electrostatic interactions, pH and chemical denaturants have a marked effect on the stability, structure, and function of many globular proteins. ANS binding studies have been conducted to enable understanding of the folding mechanism of the protein in the presence of the denaturants. Spectroscopic studies by absorbance, fluorescence, and circular dichroism and use of K2D software revealed that the enzyme has α + β type secondary structure with approximately 29% α-helix, 24% β-sheet, and 47% random coil. Under neutral conditions the enzyme is stable in urea whereas GuHCl-induced equilibrium unfolding was cooperative. A. niger RNase has little ANS binding even under neutral conditions. Multiple intermediates were populated during the pH-induced unfolding of A. niger RNase. Urea and temperature-induced unfolding of A. niger RNase into the molten globule-like state is non-cooperative, in contrast to the cooperativity seen with the native protein, suggesting the presence of two parts/domains, in the molecular structure of A. niger RNase, with different stability that unfolds in steps. Interestingly, the GuHCl-induced unfolding of the A state (molten globule state) of A. niger RNase is unique, because a low concentration of denaturant not only induces structural change but also facilitates transition from one molten globule like state (A(MG1)) into another (I(MG2)).

  2. Ultrahigh nanoparticle stability against salt, pH, and solvent with retained surface accessibility via depletion stabilization.

    Science.gov (United States)

    Zhang, Xu; Servos, Mark R; Liu, Juewen

    2012-06-20

    For many applications, it is desirable to stabilize colloids over a wide range of buffer conditions while still retaining surface accessibility for adsorption and reaction. Commonly used charge or steric stabilization cannot achieve this goal since the former is sensitive to salt and the latter blocks the particle surface. We use depletion stabilization in the presence of high molecular weight polyethylene glycol (PEG) to stabilize a diverse range of nanomaterials, including gold nanoparticles (from 10 to 100 nm), graphene oxide, quantum dots, silica nanoparticles, and liposomes in the presence of Mg(2+) (>1.6 M), heavy metal ions, extreme pH (pH 1-13), organic solvents, and adsorbed nucleosides and drugs. At the same time, the particle surface remains accessible for adsorption of both small molecules and macromolecules. Based on this study, high loading of thiolated DNA was achieved in one step with just 2% PEG 20,000 in 2 h.

  3. Physical vapor deposited films of a perylene derivative: supramolecular arrangement and thermal stability

    Energy Technology Data Exchange (ETDEWEB)

    Fernandes, Jose Diego; Alessio, Priscila; Silva, Matheus Rodrigues Medeiros; Aroca, Ricardo Flavio; Souza, Agda Eunice de; Constantino, Carlos Jose Leopoldo, E-mail: case@fct.unesp.br [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Presidente Prudente, SP (Brazil). Dept. de Fisica

    2017-07-15

    The analysis of supramolecular arrangement is essential to understand the role of this key factor on the optical and electrical properties of organic thin films. In this work, thin solid films of bis(phenethylimido) perylene (PhPTCD) fabricated using physical vapor deposition (PVD) technique (thermal evaporation), deposited simultaneously onto different substrates (Ag mirror, Ge, and quartz plates) contingent on the characterization technique. The main objective is to study the PhPTCD supramolecular arrangement and the thermal stability of this arrangement in PVD films. The ultraviolet-visible absorption reveals a controlled growth of the PVD films, and the micro-Raman scattering data show that the PhPTCD molecule is not thermally degraded in the conditions of these experiments. The microscopy also shows a homogeneous morphological surface of the PVD film at macro and micro scales, with molecular aggregates at nanoscale. Besides, the PVD film roughness does not follow substrate roughness. The X-ray diffraction indicates a crystalline structure for PhPTCD powder and an amorphous form for PhPTCD PVD film. The infrared absorption spectroscopy points to a preferential flat-on organization of the molecules in the PVD films. In addition, the annealing process (200 deg C for 20 minutes) does not affect the supramolecular arrangement of the PhPTCD PVD films. (author)

  4. Physical vapor deposited films of a perylene derivative: supramolecular arrangement and thermal stability

    International Nuclear Information System (INIS)

    Fernandes, Jose Diego; Alessio, Priscila; Silva, Matheus Rodrigues Medeiros; Aroca, Ricardo Flavio; Souza, Agda Eunice de; Constantino, Carlos Jose Leopoldo

    2017-01-01

    The analysis of supramolecular arrangement is essential to understand the role of this key factor on the optical and electrical properties of organic thin films. In this work, thin solid films of bis(phenethylimido) perylene (PhPTCD) fabricated using physical vapor deposition (PVD) technique (thermal evaporation), deposited simultaneously onto different substrates (Ag mirror, Ge, and quartz plates) contingent on the characterization technique. The main objective is to study the PhPTCD supramolecular arrangement and the thermal stability of this arrangement in PVD films. The ultraviolet-visible absorption reveals a controlled growth of the PVD films, and the micro-Raman scattering data show that the PhPTCD molecule is not thermally degraded in the conditions of these experiments. The microscopy also shows a homogeneous morphological surface of the PVD film at macro and micro scales, with molecular aggregates at nanoscale. Besides, the PVD film roughness does not follow substrate roughness. The X-ray diffraction indicates a crystalline structure for PhPTCD powder and an amorphous form for PhPTCD PVD film. The infrared absorption spectroscopy points to a preferential flat-on organization of the molecules in the PVD films. In addition, the annealing process (200 deg C for 20 minutes) does not affect the supramolecular arrangement of the PhPTCD PVD films. (author)

  5. Phosphane-stabilized gold clusters: investigation of the stability of [Au(13)(PMe (2)Ph) (10)Cl (2)] (3+).

    Science.gov (United States)

    Li, Jia; Wang, Shu-Guang

    2010-03-01

    The phosphane-stabilized gold cluster [Au(13)(PMe(2)Ph)(10)Cl(2)](3+) was studied using density functional theory. The extraordinary stability of the cluster has been attributed to the stability of the gold core and the protection conferred by ligands. Here, five stability factors of the gold core were explained and verified by investigating the Au (13) (5+) core in detail. Interactions between the gold core and several PR(3) ligands (R = Me, H, I, Br, Cl, F) were investigated according to the different electron donor abilities of each ligand; bonding energy between the ligand and the gold core was found to increase with the electronegativity of the R substituent. Furthermore, two other aspects of the ligands were clarified: how the ligand stabilizes the Au (13) (5+) core, and which kind of ligand provides the best stabilization for the cluster.

  6. Stabilization of pH in solid-matrix hydroponic systems

    Science.gov (United States)

    Frick, J.; Mitchell, C. A.

    1993-01-01

    2-[N-morpholino]ethanesulfonic acid (MES) buffer or Amberlite DP-1 (cation-exchange resin beads) were used to stabilize substrate pH of passive-wicking, solid-matrix hydroponic systems in which small canopies of Brassica napus L. (CrGC 5-2, genome : ACaacc) were grown to maturity. Two concentrations of MES (5 or 10 mM) were included in Hoagland 1 nutrient solution. Alternatively, resin beads were incorporated into the 2 vermiculite : 1 perlite (v/v) growth medium at 6% or 12% of total substrate volume. Both strategies stabilized pH without toxic side effects on plants. Average seed yield rates for all four pH stabilization treatments (13.3 to 16.9 g m-2 day-1) were about double that of the control (8.2 g m-2 day-1), for which there was no attempt to buffer substrate pH. Both the highest canopy seed yield rate (16.9 g m-2 day-1) and the highest shoot harvest index (19.5%) occurred with the 6% resin bead treatment, even though the 10 mM MES and 12% bead treatments maintained pH within the narrowest limits. The pH stabilization methods tested did not significantly affect seed oil and protein contents.

  7. Thermal stability of ultrasoft Fe-Zr-N films

    NARCIS (Netherlands)

    Chechenin, NG; van Veen, A; Schut, H; Chezan, AR; Boerma, D; Vystavel, T; De Hosson, JTM

    2003-01-01

    The thermal stability of nanocrystalline ultrasoft magnetic (Fe98Zr2)(1-x)N-x films with x = 0.10-0.25 was studied using thermal desorption spectrometry, positron beam analysis and high resolution transmission electron microscopy. The results demonstrate that grain growth during the heat treatment

  8. Thermal stability of α-amylase in aqueous cosolvent systems

    Indian Academy of Sciences (India)

    Prakash

    Enhancement of the structural stability of enzymes is of great importance for their application in several industrial processes. The mechanism of thermal denaturation depends on various physicochemical parameters of the solution in which the reaction is catalysed. Any process that enhances the structural stability and rate ...

  9. Polyaniline Conducting Electroactive Polymers Thermal and Environmental Stability Studies

    OpenAIRE

    Ansari, Reza; Keivani, M. B.

    2006-01-01

    In the current studies, polyaniline (PANi) was prepared both chemical and electrochemically in the presence of different bronsted acids from aqueous solutions. The effect of thermal treatment on electrical conductivity, and thermal stability of the PANi conducting polymers were investigated using 4-point probe and TGA techniques respectively. It was found that polymer prepared by CV method is more thermally stable than those prepared by the other electrochemical techniques. In this paper we h...

  10. Analysis of green tea compounds and their stability in dentifrices of different pH levels.

    Science.gov (United States)

    Jang, Jong-Hwa; Park, Yong-Duk; Ahn, Hyo-Kwang; Kim, Seung-Jin; Lee, Joo-Young; Kim, Eun-Cheol; Chang, Yeon-Soo; Song, Yun-Jung; Kwon, Ha-Jeong

    2014-01-01

    In this study, green tea compounds (flavonoids, alkaloids, and phenolic acids) were analyzed in green tea-containing dentifrices, and their stability at different pH levels was evaluated. The compounds were separated under 0.01% phosphoric acid-acetonitrile gradient conditions and detected by photodiode array detector at 210, 280, 300, 335 nm. Column temperature was set at 20°C based on the results of screening various temperatures. Each compound showed good linearity at optimized wavelength as well as showing good precision and accuracy in dentifrices. Using this method, the stability of compounds was investigated in pH 4, 7, 8, and 10 solutions for 96 h, and in pH 7 and pH 10 solutions for 6 months. The green tea compounds were more stable at low pH levels; purine alkaloids were more stable than flavonoids. In particular, gallocatechin (GC), epigallocatechin (EGC), epigallocatechin gallate (EGCG), gallocatechin gallate (GCG), and myricetin almost disappeared in pH 10 solutions after 96 h. In dentifrices, the compounds were gradually decreased until 6 months in both pH types, while gallic acid was increased because of production of galloyl ester of other green tea compounds. Therefore, it is beneficial to adjust to as low a pH as possible when produce green tea-containing dentifrices.

  11. On thermal stability in incompressible slip flow

    International Nuclear Information System (INIS)

    Bestman, A.R.

    1990-12-01

    The paper considers the classical problem of the stability of a layer of fluid heated from below, but in the case when the density is low and there is slip flow at the bounding walls. The eigenvalue problem which ensures is tackled by taking cognisance of the orthogonality of Bessel function of the first kind. It is observed that the Rayleigh number for the onset of instability, for the case of marginal stability, is increased by gas rarefication. (author). 2 refs

  12. The effect of pH on the stability of smectite

    International Nuclear Information System (INIS)

    Johnston, R.M.; Miller, H.G.

    1984-11-01

    The hydrothermal stability of smectite at temperatures less than 275 degrees C was investigated experimentally over a range of pH values. In the near-neutral pH region, the smectite to illite conversion predominated; in the mildly acid region, there was extensive formation of aluminum hydroxy interlayers in the clay; and in the alkaline region, framework silicates (feldspar and zeolites) were produced. The geological evidence for these reactions is also reviewed

  13. Aging effects on vertical graphene nanosheets and their thermal stability

    Science.gov (United States)

    Ghosh, S.; Polaki, S. R.; Ajikumar, P. K.; Krishna, N. G.; Kamruddin, M.

    2018-03-01

    The present study investigates environmental aging effects and thermal stability of vertical graphene nanosheets (VGN). Self-organized VGN is synthesized by plasma enhanced chemical vapor deposition and exposed to ambient conditions over 6-month period to examine its aging behavior. A systematic inspection is carried out on morphology, chemical structure, wettability and electrical property by scanning electron microscopy, Raman spectroscopy, X-ray photoelectron spectroscopy, water contact angle and four-probe resistivity measurements at regular intervals, respectively. Detailed microscopic and spectroscopic analysis substantiated the retention of graphitic quality and surface chemistry of VGN over the test period. An unchanged sheet resistance and hydrophobicity reveals its electrical and wetting stability over the time, respectively. Thermogravimetric analysis ensures an excellent thermal stability of VGN up to 575 °C in ambient atmosphere. These findings of long-term morphological, structural, wetting, electrical and thermal stability of VGN validate their potential utilization for the next-generation device applications.

  14. Thermal conductivity of ytterbia-stabilized zirconia

    International Nuclear Information System (INIS)

    Feng, Jing; Ren, Xiaorui; Wang, Xiaoyan; Zhou, Rong; Pan, Wei

    2012-01-01

    The 3–10 mol.% Yb 2 O 3 –ZrO 2 (YbSZ) ceramics were synthesized by solid reaction methods and sintered at 1600 °C. The phases were identified by high-resolution X-ray diffraction with a K α1 monochromator, and it was found that the tetragonal-prime phases exist in 3–6 mol.% YbSZ. The thermal conductivity of the sintered YbSZ ceramics were measured using a laser flash method and it was demonstrated that the values of the thermal conductivities of the 5 and 10 mol.% YbSZ ceramics are the lowest at high and room temperature, respectively, and much lower than that of 7YSZ. The lower thermal conductivity of YbSZ ceramics may be due to the heavier dopant of ytterbium and the tetragonal-prime ZrO 2 phase.

  15. On the thermal stability length dependence of high TC superconductors

    International Nuclear Information System (INIS)

    Maytal, B.Z.; Yang, S.; Waldrop, J.; Pfotenhauer, J.M.

    1996-01-01

    The margin of stability for high T c superconductors may be characterized by the lowest thermal pulse that results in a quench. A numerical code, developed to investigate this stability margin, accounts for the temperature dependence of the thermal conductivity, electrical resistivity and heat capacity of the materials involved. The conductor is cooled solely by thermal conduction along its length, and its stability is studied as function of the length. It is found that the stability margin for a pure BSCCO 2212 conductor is independent of the length. However, the stability margin for a composite conductor obtained by adding 10 % (by volume) of silver to the BSCCO is found to be strongly length dependent. A transition length is identified, for which shorter lengths exhibit a dramatically higher stability margin. This feature results when the length dependent thermal diffusion time is shorter than the time required to determine the conductor's stability. This study confirms and explains the growing awareness that if normal zones appear in high T c coils, they will remain fairly localized

  16. Water-rock interactions and the pH stability of groundwater from Yucca Mountain, Nevada

    International Nuclear Information System (INIS)

    Ebinger, M.H.

    1992-01-01

    Titrations of acidic solutions in waters from the tuff and carbonate aquifers at Yucca Mountain were simulated using the geochemical codes PHREEQE and EQ3/6. The simulations tested pH stability of the waters in the presence of different minerals and in their absence. Two acidic solutions, 10 -4 HCl and 10 -4 M UO 2 (NO 3 ) 2 , were titrated in to the water. Little pH and/or compositional change resulted in the groundwater when the HCl solution was titrated, but significant pH and CO 2 fugacity changes were observed when UO 2 (NO 3 ) 2 was titrated. Water interactions with alkali feldspar, quartz or cristobalite, and Ca-smectite buffered the pH and compositional changes in the carbonate water and decreased the magnitude of pH and compositional changes when small volumes of UO 2 (NO 3 ) 2 added to the tuffaceous waters

  17. Purification, characterization, and solvent-induced thermal stabilization of ficin from Ficus carica.

    Science.gov (United States)

    Devaraj, Kamsagara Basavarajappa; Kumar, Parigi Ramesh; Prakash, Vishweshwaraiah

    2008-12-10

    Ficin (EC 3.4.22.3), a cysteine proteinase isolated from the latex of a Ficus tree, is known to occur in multiple forms. Although crude ficin is of considerable commercial importance, ficin as such has not been fully characterized. A major ficin from the commercial crude proteinase mixture preparation of Ficus carica was purified and characterized. The purified enzyme was homogeneous in both sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) and gel-filtration chromatography and is a single polypeptide chain protein with a molecular mass of 23 100 +/- 300 Da as determined by matrix-assisted laser desorption ionization-time of flight (MALDI-TOF). The enzyme was active in the pH range of 6.5-8.5, and maximum activity was observed at pH 7.0. The N-terminal core sequence of ficin has homology with N-terminal sequences of plant cysteine proteinases. The enzyme contains three disulfide bonds and a single free cysteine residue at the active site. The effect of co-solvents, such as sorbitol, trehalose, sucrose, and xylitol, on the thermal stability of ficin was determined by activity measurements, fluorescence, and thermal denaturation studies. The apparent thermal denaturation temperature (T(m)) of ficin was significantly increased from the control value of 72 +/- 1 degrees C in the presence of all co-solvents. However, the maximum stabilization effect was observed in terms of thermal stabilization by the co-solvent trehalose.

  18. Morphology, thermal stability and thermal degradation kinetics of ...

    Indian Academy of Sciences (India)

    2016-08-26

    Aug 26, 2016 ... Different differential and integral isoconversional methods have been employed to determine the thermal degradation activation energy of UFC. Substantial variation in activation energy with the advancement of reaction verifiesmulti-step reaction pathway of UFC. A plausible interpretation of the obtained ...

  19. Thermal Plasma Generators with Water Stabilized Arc

    Czech Academy of Sciences Publication Activity Database

    Hrabovský, Milan

    2009-01-01

    Roč. 2, č. 1 (2009), s. 99-104 ISSN 1876-5343 R&D Projects: GA ČR GA202/08/1084 Institutional research plan: CEZ:AV0Z20430508 Keywords : Thermal plasma * plasma torch * Gerdien arc Subject RIV: BL - Plasma and Gas Discharge Physics http://www.bentham.org/open/toppj/openaccess2.htm

  20. Thermal Stability of Rhodopsin and Progression of Retinitis Pigmentosa

    Science.gov (United States)

    Liu, Monica Yun; Liu, Jian; Mehrotra, Devi; Liu, Yuting; Guo, Ying; Baldera-Aguayo, Pedro A.; Mooney, Victoria L.; Nour, Adel M.; Yan, Elsa C. Y.

    2013-01-01

    Over 100 point mutations in the rhodopsin gene have been associated with retinitis pigmentosa (RP), a family of inherited visual disorders. Among these, we focused on characterizing the S186W mutation. We compared the thermal properties of the S186W mutant with another RP-causing mutant, D190N, and with WT rhodopsin. To assess thermal stability, we measured the rate of two thermal reactions contributing to the thermal decay of rhodopsin as follows: thermal isomerization of 11-cis-retinal and hydrolysis of the protonated Schiff base linkage between the 11-cis-retinal chromophore and opsin protein. We used UV-visible spectroscopy and HPLC to examine the kinetics of these reactions at 37 and 55 °C for WT and mutant rhodopsin purified from HEK293 cells. Compared with WT rhodopsin and the D190N mutant, the S186W mutation dramatically increases the rates of both thermal isomerization and dark state hydrolysis of the Schiff base by 1–2 orders of magnitude. The results suggest that the S186W mutant thermally destabilizes rhodopsin by disrupting a hydrogen bond network at the receptor's active site. The decrease in the thermal stability of dark state rhodopsin is likely to be associated with higher levels of dark noise that undermine the sensitivity of rhodopsin, potentially accounting for night blindness in the early stages of RP. Further studies of the thermal stability of additional pathogenic rhodopsin mutations in conjunction with clinical studies are expected to provide insight into the molecular mechanism of RP and test the correlation between rhodopsin's thermal stability and RP progression in patients. PMID:23625926

  1. Thermal stability of PMMA–clay hybrids

    Indian Academy of Sciences (India)

    Administrator

    stability of these different clay–PMMA hybrids have been studied and compared with that of pure PMMA by differential scanning calorimeter (DSC). The bonding of clay with PMMA has been studied by IR. Morpho- logy of clay–PMMA hybrids has been shown by SEM and XRD which indicate partially exfoliated structure in.

  2. Morphology, thermal stability and thermal degradation kinetics of ...

    Indian Academy of Sciences (India)

    Different differential and integral isoconversional methods have been employed to determine the thermal degrada- tion activation energy of UFC. .... β(dE/dT). RT. − β. T. { n+. Eα. RT. } + d2α/dt2 dα/dt. ] . (8). Under invariant conditions of α, equation (6) can be trans- formed into the following equation: y = a(x)b exp(−c/x),. (9) ...

  3. Thermal stability of the tokamak plasma edge

    International Nuclear Information System (INIS)

    Stacey, W.M.

    1997-01-01

    The general linear, fluid, thermal instability theory for the plasma edge has been extended. An analysis of a two-dimensional fluid model of the plasma edge has identified the importance of many previously unappreciated phenomena associated with parallel and gyroviscous forces in the presence of large radial gradients, with large radial or parallel flows, with the temperature dependence of transport coefficients, and with the coupling of temperature, flow and density perturbations. The radiative condensation effect is generalized to include a further destabilizing condensation effect associated with radial heat conduction. Representative plasma edge neutral and impurity densities are found to be capable of driving thermal instabilities in the edge transport barrier and radiative mantle, respectively. (author)

  4. Effect of thermal protectants on the stability of bovine milk immunoglobulin G

    International Nuclear Information System (INIS)

    Chen, C.C.; Chang, H.M.

    1998-01-01

    pH stability, thermal stability, and the effect of homogenization and ultrasonic treatment on the stability of bovine milk immunoglobulin G (IgG) in model systems was studied. Separated IgG (0.02 mg/mL) was found to be unstable and susceptible to denaturation when incubated at pH 4 or 10 or thermally treated at temperature 75 degrees C. IgG in the colostrum, on the other hand, was found to be much more stable than in whey or in PBS when thermally treated at temperatures in the range of 75-100 degrees C. The residual IgC content reduced more sharply with increasing heating times, and almost no IgG content was detected when IgG in PBS (0.15 M NaCl/0.01 M phosphate buffer, pH 7.0) was heated at 95 degrees C for 15 s, whereas the corresponding residual IgG contents in whey and colostrum were found to be 42 and 59%, respectively. For IgG in PBS heated at 95 degrees C for 15 s, addition of 5% fructose or maltose displayed most remarkable protection effects by raising the residual IgG content to 31%, followed by sucrose, lactose, glucose, and galactose. However, extravagant addition ( 30%) to IgG in PBS led to a decline in residual IgG content. Addition of 0.4% glutamic acid and 2% glycine to IgG in PBS heated at 95 degrees C for 15 s also remarkably improved the residual IgG content by 13.5 and 26.7%, respectively. Glycerol and sugar alcohol, such as sorbitol, stabilized IgG during the thermal treatment

  5. A pH dependence study of CdTe quantum dots fluorescence quantum yields using eclipsing thermal lens spectroscopy

    International Nuclear Information System (INIS)

    Estupiñán-López, C.; Dominguez, C. Tolentino; Filho, P.E. Cabral; Santos, B.S.; Fontes, A.; Araujo, R.E. de

    2016-01-01

    In this study we evaluated the absolute fluorescence quantum yield (Φ) of hydrophilic CdTe QDs in function of different pHs, modified from the alkaline to acid, by using two different chemicals compounds, the mercaptosuccinic acid (MSA-the stabilizing agent of the QDs synthesis) or hydrochloric acid (HCl). The pH control of QDs suspensions is essential for the use of fluorescent nanoparticles in biological systems. We used the eclipsing thermal lens spectroscopy technique to determine the absolute fluorescence quantum yield values. The results showed variations on the Φ values as a function of the pH, which allowed a better understanding of QDs emission characteristics, establishing parameters for their use in biomedical applications such as optical images of biological systems, immunoassays, flow cytometry, biosensors and others.

  6. The Effects of pH and Heat Treatment Processing on the Stability of ...

    African Journals Online (AJOL)

    This study was carried out to investigate the effects of pH and heat treatment processing on stability and natural food colours used in dairy products. A repeated laboratory experiment was conducted in which loss of colour intensity or change in shade of natural food colours used in acid and nearly neutral dairy products at ...

  7. Stability and Relative Stability of Linear Systems with Many Constant Time Delays. Ph.D. Thesis

    Science.gov (United States)

    Barker, Larry Keith

    1976-01-01

    A method of determining the stability of linear systems with many constant time delays is developed. This technique, an extension of the tau-decomposition method, is used to examine not only the stability but also the relative stability of retarded systems with many delays and a class of neutral equations with one delay. Analytical equations are derived for partitioning the delay space of a retarded system with two time delays. The stability of the system in each of the regions defined by the partitioning curves in the parameter plane is determined using the extended tau-decomposition method. In addition, relative stability boundaries are defined using the extended tau-decompositon method in association with parameter plane techniques. Several applications of the extended tau-decomposition method are presented and compared with stability results obtained from other analyses. In all cases the results obtained using the method outlined herein coincide with and extend those of previous investigations. The extended tau-decomposition method applied to systems with time delays requires less computational effort and yields more complete stability analyses than previous techniques.

  8. The Thermal Stabilization of Vaccines Against Agents of Bioterrorism

    Science.gov (United States)

    2005-09-01

    Stability of Adenovirus Type 2 as a Function of pH Jason Rexroad’, Talia Martin1, David McNeilly, Simon Godwin2, and C. Russell Middaugh’* ’Department of...1507-1512. 19. Huyghe BG, Liu X, Sutjipto S, Sugarman BJ, Horn MT, Shepard HM, Scandella CJ, Shabram P 1995. Purification of a type 5 recombinant

  9. Stabilizing the thermal lattice Boltzmann method by spatial filtering.

    Science.gov (United States)

    Gillissen, J J J

    2016-10-01

    We propose to stabilize the thermal lattice Boltzmann method by filtering the second- and third-order moments of the collision operator. By means of the Chapman-Enskog expansion, we show that the additional numerical diffusivity diminishes in the low-wavnumber limit. To demonstrate the enhanced stability, we consider a three-dimensional thermal lattice Boltzmann system involving 33 discrete velocities. Filtering extends the linear stability of this thermal lattice Boltzmann method to 10-fold smaller transport coefficients. We further demonstrate that the filtering does not compromise the accuracy of the hydrodynamics by comparing simulation results to reference solutions for a number of standardized test cases, including natural convection in two dimensions.

  10. pH stability and comparative evaluation of ranaspumin-2 foam for application in biochemical reactors

    International Nuclear Information System (INIS)

    Choi, Hyo-Jick; Ebersbacher, Charles F; Quan, Fu-Shi; Montemagno, Carlo D

    2013-01-01

    Aqueous channels of foam represent a simplified, natural bioreactor on the micro-/nano-scale. Previous studies have demonstrated the feasibility and potential application of foams in replicating cellular process in vitro, but no research has been performed to establish a basis for designing stable and biocompatible foam formulations. Our research has been directed specifically to the evaluation of ranaspumin-2 (RSN-2), a frog foam nest protein. The strong surfactant activity of RSN-2 enabled us to produce foams using low protein concentration (1 mg ml −1 ) over a wide pH range (pH ≥ 3). Importantly, the RSN-2 formulation exhibited the best foam stability at a near neutral pH condition, which shows a potential for application to various biosynthesis applications. Model cellular systems such as liposomes and inactivated A/PR/8/34 influenza virus maintained their physicochemical stability and full hemagglutination activity, indicating biocompatibility of RSN-2 with both cellular membranes and proteins both in bulk solution and in foam. Moreover, the addition of RSN-2 did not exert any deteriorative effects on bacterial cell growth kinetics. In contrast, Tween 20, Triton X-100, and BSA did not show satisfactory performance in terms of foamability, foam stability, physicochemcial stability, and biochemical stability. Although our study has been limited to representative formulations composed of only surfactant molecules, a number of unique advantages make RSN-2 a promising candidate for in vitro foam biosynthesis. (paper)

  11. Novel Antimicrobial Organic Thermal Stabilizer and Co-Stabilizer for Rigid PVC

    Directory of Open Access Journals (Sweden)

    Nadia A. Mohamed

    2012-07-01

    Full Text Available Biologically active N-benzoyl-4-(N-maleimido-phenylhydrazide (BMPH was synthesized and its structure was confirmed by elemental analysis and various spectral tools. It was examined as a thermal stabilizer and co-stabilizer for rigid poly (vinyl chloride at 180 °C in air. Blending BMPH with reference samples in different ratios greatly lengthens the thermal stability value and improves the extent of discoloration of PVC. TGA confirmed the improved stability of PVC in presence of the investigated organic stabilizer. GPC measurements were done to investigate the changes occurred in the molecular masses of the degraded samples of blank PVC and PVC in presence of the novel stabilizer. BMPH showed good antimicrobial activity towards two kinds of bacteria and two kinds of fungi.

  12. Thermal barrier coating having high phase stability

    Science.gov (United States)

    Subramanian, Ramesh

    2001-01-01

    A device (10) comprising a substrate (22) having a deposited ceramic thermal barrier coating layer (20) characterized by a microstructure having gaps (28) where the thermal barrier coating (20) consists essentially of a pyrochlore crystal structure having a chemical formula consisting essentially of A.sup.n+.sub.2-x B.sup.m+.sub.2+x O.sub.7-y, where A is selected from the group of elements selected from La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, and mixtures thereof; where B is selected from the group of elements selected from Zr, Hf, Ti and mixtures thereof; n and m are the valence of A and B respectively, and for -0.5.ltoreq.x.ltoreq.0.5, ##EQU1## and excluding the following combinations for x=0, y=0: A=La and B=Zr; A=La and B=Hf; A=Gd and B=Hf; and A=Yb and B=Ti.

  13. Method for enhancing the thermal stability of ionic compounds

    DEFF Research Database (Denmark)

    2013-01-01

    This invention relates to a method for enhancing the thermal stability of ionic compounds including ionic liquids, by immobilization on porous solid support materials having a pore diameter of between about 20-200 AA, wherein the solid support does not have a pore size of 90 AA.......This invention relates to a method for enhancing the thermal stability of ionic compounds including ionic liquids, by immobilization on porous solid support materials having a pore diameter of between about 20-200 AA, wherein the solid support does not have a pore size of 90 AA....

  14. Thermal stability of Cryptococcus albidus α-L-rhamnosidase

    Directory of Open Access Journals (Sweden)

    O. V. Gudzenko

    2015-06-01

    Full Text Available Yeast as well as micromycetes α-L-rhamnosidases, currently, are the most promising group of enzymes. Improving of the thermal stability of the enzyme preparation are especially important studies. Increase in stability and efficiency of substrate hydrolysis by α-L-rhamnosidase will improve the production technology of juices and wines. The aim of our study was to investigate the rate of naringin hydrolysis by α-L-rhamnosidase from Cryptococcus albidus, and also some aspects of the thermal denaturation and stabilization of this enzyme. We investigated two forms of α-L-rhamnosidase from C. albidus, which were obtained by cultivation of the producer on two carbon sources – naringin and rhamnose. A comparative study of properties and the process of thermal inactivation of α-L-rhamnosidases showed that the inducer of synthesis had no effect on the efficiency of naringin hydrolysis by the enzyme, but modified thermal stability of the protein molecule. Hydrophobic interactions and the cysteine residues are involved in maintaining of active conformation of the α-L-rhamnosidase molecule. Yeast α-L-rhamnosidase is also stabilized by 0.5% bovine serum albumin and 0.25% glutaraldehyde.

  15. Thermal stability of polyvinyl alcohol/nanocrystalline cellulose composites.

    Science.gov (United States)

    Voronova, Marina I; Surov, Oleg V; Guseinov, Sabir S; Barannikov, Vladimir P; Zakharov, Anatoly G

    2015-10-05

    Thermal stability of polyvinyl alcohol/cellulose nanocrystals (PVA/CNCs) composites prepared with solution casting technique was studied. The PVA/CNCs composites were characterized by Fourier transform infrared spectrometry, X-ray diffraction, differential scanning calorimeter (DSC) and thermogravimetric (TG) analysis. Due to the presence of CNCs nanoparticles, thermal degradation of the composites occurs at much higher temperatures compared to that of the neat PVA. Thermal stability of the PVA/CNCs composites is maximally enhanced with CNCs content of 8-12 wt%. Some thermal degradation products of the PVA/CNCs composites were identified by mass spectrometric analysis. TG measurements with synchronous recording of mass spectra revealed that the thermal degradation of both CNCs and PVA in the composites with CNCs content of 8-12 wt% occurs simultaneously at a much higher temperature than that of CNCs or the neat PVA. However, with increasing CNCs content more than 12 wt% the thermal stability of the composites decreases. In this case, the degradation of CNCs comes first followed by the degradation of PVA. Copyright © 2015 Elsevier Ltd. All rights reserved.

  16. Improved i-motif thermal stability by insertion of anthraquinone monomers

    DEFF Research Database (Denmark)

    Gouda, Alaa S; Amine, Mahasen S.; Pedersen, Erik Bjerregaard

    2017-01-01

    In order to gain insight into how to improve thermal stability of i-motifs when used in the context of biomedical and nanotechnological applications, novel anthraquinone-modified i-motifs were synthesized by insertion of 1,8-, 1,4-, 1,5- and 2,6-disubstituted anthraquinone monomers into the TAA...... loops of a 22mer cytosine-rich human telomeric DNA sequence. The influence of the four anthraquinone linkers on the i-motif thermal stability was investigated at 295 nm and pH 5.5. Anthraquinone monomers modulate the i-motif stability in a position-depending manner and the modulation also depends...... on the substitution pattern of the anthraquinone. The insertion of anthraquinone was found to stabilize the i-motif structure when replacing any one of the positions of the central TAA loop and the thermal stabilities were typically higher than those previously found for i-motifs containing pyrene-modified uracilyl...

  17. Degradation Behavior of Thermal Stabilized Polyacrylonitrile Fibers

    Directory of Open Access Journals (Sweden)

    LEI Shuai

    2017-05-01

    Full Text Available In the temperature range of 300-800℃, 40%-50% of the mass lost during the processing of polyacrylonitrile based carbon fiber (PANCF. Understanding the degradation behavior will be valuable in understanding the formation mechanism of pseudo-graphite structure, and providing theoretic basis for producing high performance carbon fiber and increasing the carbonization yield. The simulation of the degradation progress was carried out on the thermogravimetric analyzer (TGA, the results show that there are two degradation steps for PAN fiber stabilized in air, and controlled by cyclization coefficient and oxygen content. The cyclization coefficient and oxygen content are effective to the density of carbon fiber by influencing the degradation behavior, which cause defects in the fiber. The higher cyclization coefficient leads to form less structural defects and higher density of the fiber; on the contrary, the higher oxygen content leads to form more structural defects and lower density of the fiber.

  18. A linear stability analysis of supercritical water reactors, (1). Thermal-hydraulic stability

    International Nuclear Information System (INIS)

    Tin Tin Yi; Koshizuka, Seiichi; Oka, Yoshiaki

    2004-01-01

    This paper summarizes the analysis results of the thermal-hydraulic stability of a high-temperature reactor cooled and moderated by supercritical-pressure light water (SCLWR-H). A linear stability analysis code in the frequency domain was developed to study the thermal-hydraulic stability of SCLWR-H at constant supercritical pressure. The analysis method is based on linearization by perturbation of numerically-discretized one-dimensional single-channel single-phase conservation equations. The effect of water rods on stability is considered. The thermal-hydraulic stability of SCLWR-H for full-power and partial-power normal operations was investigated by frequency domain method. Our analysis reveals that though SCLWR-H has low coolant flow rate and large density change in the core, the thermal-hydraulic stability can be maintained both at normal operation and during power raising phase of constant pressure startup by applying an orifice pressure drop coefficient an the inlet of the fuel assemblies. A parametric study was also carried out to determine the parameters affecting the stability. (author)

  19. Monomeric banana lectin at acidic pH overrules conformational stability of its native dimeric form.

    Directory of Open Access Journals (Sweden)

    Javed M Khan

    Full Text Available Banana lectin (BL is a homodimeric protein categorized among jacalin-related family of lectins. The effect of acidic pH was examined on conformational stability of BL by using circular dichroism, intrinsic fluorescence, 1-anilino-8-napthalene sulfonate (ANS binding, size exclusion chromatography (SEC and dynamic light scattering (DLS. During acid denaturation of BL, the monomerization of native dimeric protein was found at pH 2.0. The elution profile from SEC showed two different peaks (59.65 ml & 87.98 ml at pH 2.0 while single peak (61.45 ml at pH 7.4. The hydrodynamic radii (R h of native BL was 2.9 nm while at pH 2.0 two species were found with R h of 1.7 and 3.7 nm. Furthermore at, pH 2.0 the secondary structures of BL remained unaltered while tertiary structure was significantly disrupted with the exposure of hydrophobic clusters confirming the existence of molten globule like state. The unfolding of BL with different subunit status was further evaluated by urea and temperature mediated denaturation to check their stability. As inferred from high Cm and ΔG values, the monomeric form of BL offers more resistance towards chemical denaturation than the native dimeric form. Besides, dimeric BL exhibited a Tm of 77°C while no loss in secondary structures was observed in monomers even up to 95°C. To the best of our knowledge, this is the first report on monomeric subunit of lectins showing more stability against denaturants than its native dimeric state.

  20. Theoretical bases on thermal stability of layered metallic systems

    International Nuclear Information System (INIS)

    Kadyrzhanov, K.K.; Rusakov, V.S.; Turkebaev, T.Eh.; Zhankadamova, A.M.; Ensebaeva, M.Z.

    2003-01-01

    The paper is dedicated to implementation of the theoretical bases for layered metallic systems thermal stabilization. The theory is based on the stabilization mechanism expense of the intermediate two-phase field formation. As parameters of calculated model are coefficients of mutual diffusion and inclusions sizes of generated phases in two-phase fields. The stabilization time dependence for beryllium-iron (Be (1.1 μm)-Fe(5.5 μm)) layered system from iron and beryllium diffusion coefficients, and inclusions sizes is shown as an example. Conclusion about possible mechanisms change at transition from microscopic consideration to the nano-crystal physics level is given

  1. Thermal transport properties of CaO-stabilized zirconia with varying amounts of stabilization

    International Nuclear Information System (INIS)

    Mirkovich, V.V.; Wheat, T.A.

    1985-01-01

    The thermal diffusivity of zirconia samples stabilized with 5.0, 7.6, 10.0, 15.0, 20.0 and 22.2 mol% CaO, and of a commercially available CaO-stabilized zirconia, was measured as a function of temperature. The thermal conductivity of samples with 7.5, 10.0, 15.0, and 20.0 mol% CaO was also measured as a function of temperature. The results have shown that the thermal transport properties for all compositions decrease with increasing temperature between 50 and 800 0 C. At lower temperatures (100-150 0 C), the transport properties depend principally on the CaO content of the specimen. Both thermal diffusivity and thermal conductivity show a minimum at 15.0 mol% CaO content. The grain size of the specimens appears to have no effect on these transport properties. (author)

  2. Thermal stability of Vernonia galamensis seed oil

    Directory of Open Access Journals (Sweden)

    Benny M. Wamalwa

    2000-12-01

    Full Text Available The physicochemical changes of refined vernonia oil-RVO (which naturally contains epoxidized triglycerides upon heating was evaluated and is reported in this manuscript. A boiling point range of 183 °C to 190 °C (at 760 mm Hg for the vernonia oil was obtained using the Siwolobboff's method. The oil changed its physical appearance and consistency in the course of the heating. A homogenous free-flowing beige-sand shade refined vernonia oil at room temperature (25 °C was transformed irreversibly to an intense-brown shade, becoming increasingly more viscous with increase in temperature, and ceasing to flow momentarily at 188 °C. On cooling to room temperature, the oil solidified into a brown rubber-like elastic material. The oil also exhibited a reduction in its oxirane content from 1.39 plus or minus 0.004 equivalent HBr kg-l at 25 °C to 0.542 plus or minus 0.002 equivalent HBr kg-l at 70 °C. This signifies a 61% drop in oxirane content for the 45 °C temperature rise. These findings point towards a thermally driven polymerization and/or decomposition of the refined vernonia oil (RVO.

  3. Influência do pH sobre a estabilidade de suspensões de alumina estabilizadas eletroestericamente Influence of pH on the stability of alumina suspensions electrosterically stabilized

    Directory of Open Access Journals (Sweden)

    Luciano Leal de Morais Sales

    2007-02-01

    Full Text Available In this work, aqueous suspensions of aluminas with different particle sizes were evaluated. The effect of pH on the electrosteric stabilization using PMAA-NH4 (ammonium polymethacrylate as deflocculant was studied. The amount of deflocculant was optimized and rheologic properties were determined at four different pH values. Sedimentation was also evaluated. For suspensions with pH 4, an electrostatic mechanism of stabilization was observed, probably due to a flat adsorption of PMMA- on the alumina surface, leading to a small efficiency in relation to steric stabilization. For a suspension with pH 12, the steric mechanism of stabilization prevails. Suspensions with pH 7 and 9 present a higher flocculation degree. In relation to particle size, A-1000 samples present a smaller particle size, leading to a smaller interparticle distance (IPS, making stabilization more difficult.

  4. Amide-modified poly(butylene terepthalate): thermal stability

    NARCIS (Netherlands)

    van Bennekom, A.C.M.; van Bennekom, A.C.M.; Willemsen, P.A.A.T.; Willemsen, P.A.A.T.; Gaymans, R.J.

    1996-01-01

    The thermal stability of a poly(ester amide) copolymer (PBTA) based on poly(butylene terephthalate) (PBT) and nylon-4,T with the diamide of butanediamine and dimethyl terephthalate (N,N′-bis(p-carbomethoxybenzoyl)butanediamine) and homopolymer PBT was studied. The development of inherent viscosity

  5. Morphology, thermal, electrical and electrochemical stability of nano ...

    Indian Academy of Sciences (India)

    In the present work, an attempt has been made to develop nano aluminium oxide (Al2O3)-filled polyvinyl alcohol (PVA) composite gel electrolytes. Surface morphological studies, thermal behaviour, electrochemical stability and electrical characterization of these composite gel electrolytes have been performed. An increase ...

  6. Thermal stability of gold-PS nanocomposites thin films

    Indian Academy of Sciences (India)

    Administrator

    performed at liquid nitrogen temperatures to reduce the electron–beam-induced radiation damage. The results showed a marginal increase in Au nanoparticle diameter (2⋅3 nm–3⋅6 nm) and more importantly, an improved thermal stability of the polystyrene (PS) composite film much above its glass transition tempera- ture.

  7. Thermal stability of -amylase in aqueous cosolvent systems

    Indian Academy of Sciences (India)

    The activity and thermal stability of -amylase were studied in the presence of different concentrations of trehalose, sorbitol, sucrose and glycerol. ... Department of Protein Chemistry and Technology, Central Food Technological Research Institute (A constituent laboratory of Council of Scientific and Industrial Research), ...

  8. Thermal stability of liquid antioxidative extracts from pomegranate peel

    Science.gov (United States)

    This research was carried out to assess the potential of using the natural antioxidants in pomegranate peel extracts as replacement for synthetic antioxidants. As a result the thermal stability of pomegranate peel extract products during sterilization and storage, and its effect on industrial, color...

  9. Thermal properties and stabilities of polymer thin films

    International Nuclear Information System (INIS)

    Kanaya, Toshiji; Kawashima, Kazuko; Inoue, Rintaro; Miyazaki, Tsukasa

    2009-01-01

    Recent extensive studies have revealed that polymer thin films showed very interesting but unusual thermal properties and stabilities. In the article we show that X-ray reflectivity and neutron reflectivity are very powerful tools to study the anomalous properties of polymer thin films. (author)

  10. Roughness effects on the thermal stability of thin films

    NARCIS (Netherlands)

    Palasantzas, George

    1997-01-01

    In this work, we investigate interface roughness effects on the energetic terms that play a key role on the thermal stability of thin silicide films. The roughness is modeled as a self-affine structure with power spectrum ~σ^2ξ^2(1+aq^2ξ^2)^-1-H convoluted with a domain size distribution ∝

  11. Thermal stability of α-amylase in aqueous cosolvent systems

    Indian Academy of Sciences (India)

    Prakash

    Department of Protein Chemistry and Technology, Central Food Technological Research Institute. (A constituent laboratory of Council of Scientific and Industrial Research), Mysore 570 020, India. *Corresponding author (Fax, +91-821-2516 308; Email, prakash@cftri.com). The activity and thermal stability of α-amylase were ...

  12. Morphology, thermal, electrical and electrochemical stability of nano

    Indian Academy of Sciences (India)

    In the present work, an attempt has been made to develop nano aluminium oxide (Al2O3)-filled polyvinyl alcohol (PVA) composite gel electrolytes. Surface morphological studies, thermal behaviour, electrochemical stability and electrical characterization of these composite gel electrolytes have been performed. An increase ...

  13. Differences in Thermal Stability of Glucosinolates in Five Brassica Vegetables

    NARCIS (Netherlands)

    Dekker, M.; Hennig, K.; Verkerk, R.

    2009-01-01

    The thermal stability of individual glucosinolates within five different Brassica vegetables was studied at 100°C for different incubation times up to 120 minutes. Three vegetables that were used in this study were Brassica oleracea (red cabbage, broccoli and Brussels sprouts) and two were Brassica

  14. Thermal and combined pressure--temperature inactivation of orange pectinesterase: influence of pH and additives.

    Science.gov (United States)

    Van den Broeck, I; Ludikhuyze, L R; Van Loey, A M; Weemaes, C A; Hendrickx, M E

    1999-07-01

    Inactivation of commercially available orange pectinesterase (PE) was investigated under isothermal and isothermal-isobaric conditions. In both cases, inactivation data could be accurately described by a fractional conversion model. The influence of enzyme concentration, pH, Ca(2+) concentration, and sucrose on the inactivation kinetics was studied. Enzyme stability against heat and pressure increased by increasing enzyme concentration. An increased Ca(2+) concentration caused sensitization to temperature and increased the residual fraction active PE after thermal treatment. To the contrary, in the case of pressure treatment, decreasing Ca(2+) concentrations increased pressure inactivation. The remaining fraction active PE after pressure treatment was not influenced by the addition of Ca(2+) ions. Acidification accelerated thermal as well as pressure-temperature inactivation, whereas in the presence of sucrose an increased temperature and pressure stability of orange PE was observed. Sucrose had no influence on the remaining activity after thermal treatment, but it increased the residual fraction after pressure treatment. The remaining fraction was for all additives studied independent of the pressure and temperature level applied except for the inactivation in an acid medium, when a decrease of the residual fraction was observed with increasing temperature and pressure.

  15. Lanthanide phosphonates: Synthesis, thermal stability and magnetic characterization

    Energy Technology Data Exchange (ETDEWEB)

    Amghouz, Z., E-mail: amghouz.uo@uniovi.es [Departamentos de Quimica Fisica y Analitica y Quimica Organica e Inorganica, Universidad de Oviedo - CINN, 33006 Oviedo (Spain); Garcia, J.R.; Garcia-Granda, S. [Departamentos de Quimica Fisica y Analitica y Quimica Organica e Inorganica, Universidad de Oviedo - CINN, 33006 Oviedo (Spain); Clearfield, A. [Department of Chemistry, Texas A and M University, College Station, TX 77842-3012 (United States); Rodriguez Fernandez, J.; Pedro, I. de [CITIMAC, Facultad de Ciencias, Universidad de Cantabria, 39005 Santander (Spain); Blanco, J.A. [Departamento de Fisica, Universidad de Oviedo, 33007 Oviedo (Spain)

    2012-09-25

    Highlights: Black-Right-Pointing-Pointer Report of the complete series of lanthanide 1,4-phenylbis(phosphonate). Black-Right-Pointing-Pointer Synthesis under conventional hydrothermal synthesis or microwave-assisted hydrothermal synthesis. Black-Right-Pointing-Pointer Cation size is the key factor for the structural and particles size variations. Black-Right-Pointing-Pointer Thermal behaviour is characterized by unusual very high thermal stability. - Abstract: Series of novel organic-inorganic hybrids materials based on trivalent lanthanides (Ln = Y, La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu) and 1,4-phenylbis(phosphonate) obtained under hydrothermal conditions either by oven heat or microwave irradiation. The anhydrous compounds containing La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, and Ho, are isostructural. However, the compounds based on Y, Er, Tm, Yb, and Lu are hydrated and their structures have not yet been solved. The series of compounds are characterized by PXRD, TEM, SEM-EDX and thermal analyses (TG-MS and DSC). TEM study show a variable particles size with a minimum mean-particle size of ca. 30 nm. These compounds exhibit unusual very high thermal stability. The size of particles and the thermal stability are depending on lanthanide(III) cation features. All the investigated materials show paramagnetic behaviour. The magnetic susceptibility data follow a Curie-Weiss laws with paramagnetic effective moments in good agreement with those expected for Ln{sup 3+} free ions.

  16. Temperature Stability and Control Requirements for Thermal Vacuum/Thermal Balance Testing of the Aquarius Radiometer

    Science.gov (United States)

    Johnson, Chris

    2008-01-01

    The paper describes the specific temperature stability and control requirements for the thermal vacuum and thermal balance testing of the Aquarius Instrument at the Goddard Space Flight Center in Greenbelt, Maryland. The testing was conducted in the 10' wide x 15' deep Facility 225 Thermal Vacuum chamber. The temperature control stability requirements were less than .14 C RMS thermal variation over a seven-day period. The thermal test specification also called for the ability to impose a high-resolution sinusoidal variation for all heater zones. The special requirements of the Aquarius radiometer test necessitated the construction of a multi-function test fixture and the modification of two existing heater controller racks.

  17. Stabilization of T4 bacteriophage at acidic and basic pH by adsorption on paper.

    Science.gov (United States)

    Meyer, Abigail; Greene, Melissa; Kimmelshue, Chad; Cademartiri, Rebecca

    2017-12-01

    Bacteriophages find applications in agriculture, medicine, and food safety. Many of these applications can expose bacteriophages to stresses that inactivate them including acidic and basic pH. Bacteriophages can be stabilized against these stresses by materials including paper, a common material in packaging and consumer products. Combining paper and bacteriophages creates antibacterial materials, which can reduce the use of antibiotics. Here we show that adsorption on paper protects T4, T5, and T7 bacteriophage from acidic and basic pH. We added bacteriophages to filter paper functionalized with carboxylic acid (carboxyl methyl cellulose) or amine (chitosan) groups, and exposed them to pH from 5.6 to 14. We determined the number of infective bacteriophages after exposure directly on the paper. All papers extended the lifetime of infective bacteriophage by at least a factor of four with some papers stabilizing bacteriophages for up to one week. The degree of stabilization depended on five main factors (i) the family of the bacteriophage, (ii) the charge of the paper and bacteriophages, (iii) the location of the bacteriophages within the paper, (iv) the ability of the paper to prevent bacteriophage-bacteriophage aggregation, and (v) the sensitivity of the bacteriophage proteins to the tested pH. Even when adsorbed on paper the bacteriophages were able to remove E. coli in milk. Choosing the right paper modification or material will protect bacteriophages adsorbed on that material against detrimental pH and other environmental challenges increasing the range of applications of bacteriophages on materials. Copyright © 2017 Elsevier B.V. All rights reserved.

  18. Evaluation of Thermal Stability of RNA Nanoparticles by Temperature Gradient Gel Electrophoresis (TGGE) in Native Condition.

    Science.gov (United States)

    Benkato, Kheiria; O'Brien, Benjamin; Bui, My N; Jasinski, Daniel L; Guo, Peixuan; Khisamutdinov, Emil F

    2017-01-01

    Temperature gradient gel electrophoresis (TGGE) is a powerful tool used to analyze the thermal stabilities of nucleic acids. While TGGE is a decades-old technique, it has recently gained favor in the field of RNA nanotechnology, notably in assessing the thermal stabilities of RNA nanoparticles (NPs). With TGGE, an electrical current and a linear temperature gradient are applied simultaneously to NP-loaded polyacrylamide gel, separating the negatively charged NPs based on their thermal behavior (a more stable RNA complex will remain intact through higher temperature ranges). The linear temperature gradient can be set either perpendicular or parallel to the electrical current, as either will make the NPs undergo a transition from native to denatured conformations. Often, the melting transition is influenced by sequence variations, secondary/tertiary structures, concentrations, and external factors such as the presence of a denaturing agent (e.g., urea), the presence of monovalent or divalent metal ions, and the pH of the solvent. In this chapter, we describe the experimental setup and the analysis of the thermal stability of RNA NPs in native conditions using a modified version of a commercially available TGGE system.

  19. Effects of pH and Iminosugar Pharmacological Chaperones on Lysosomal Glycosidase Structure and Stability

    Energy Technology Data Exchange (ETDEWEB)

    Lieberman, Raquel L.; D’aquino, J. Alejandro; Ringe, Dagmar; Petsko, Gregory A.; (Harvard-Med); (Brandeis)

    2009-06-05

    Human lysosomal enzymes acid-{beta}-glucosidase (GCase) and acid-{alpha}-galactosidase ({alpha}-Gal A) hydrolyze the sphingolipids glucosyl- and globotriaosylceramide, respectively, and mutations in these enzymes lead to the lipid metabolism disorders Gaucher and Fabry disease, respectively. We have investigated the structure and stability of GCase and {alpha}-Gal A in a neutral-pH environment reflective of the endoplasmic reticulum and an acidic-pH environment reflective of the lysosome. These details are important for the development of pharmacological chaperone therapy for Gaucher and Fabry disease, in which small molecules bind mutant enzymes in the ER to enable the mutant enzyme to meet quality control requirements for lysosomal trafficking. We report crystal structures of apo GCase at pH 4.5, at pH 5.5, and in complex with the pharmacological chaperone isofagomine (IFG) at pH 7.5. We also present thermostability analysis of GCase at pH 7.4 and 5.2 using differential scanning calorimetry. We compare our results with analogous experiments using {alpha}-Gal A and the chaperone 1-deoxygalactonijirimycin (DGJ), including the first structure of {alpha}-Gal A with DGJ. Both GCase and {alpha}-Gal A are more stable at lysosomal pH with and without their respective iminosugars bound, and notably, the stability of the GCase-IFG complex is pH sensitive. We show that the conformations of the active site loops in GCase are sensitive to ligand binding but not pH, whereas analogous galactose- or DGJ-dependent conformational changes in {alpha}-Gal A are not seen. Thermodynamic parameters obtained from {alpha}-Gal A unfolding indicate two-state, van't Hoff unfolding in the absence of the iminosugar at neutral and lysosomal pH, and non-two-state unfolding in the presence of DGJ. Taken together, these results provide insight into how GCase and {alpha}-Gal A are thermodynamically stabilized by iminosugars and suggest strategies for the development of new pharmacological

  20. Effects of pH and Temperature on Recombinant Manganese Peroxidase Production and Stability

    Science.gov (United States)

    Jiang, Fei; Kongsaeree, Puapong; Schilke, Karl; Lajoie, Curtis; Kelly, Christine

    The enzyme manganese peroxidase (MnP) is produced by numerous white-rot fungi to overcome biomass recalcitrance caused by lignin. MnP acts directly on lignin and increases access of the woody structure to synergistic wood-degrading enzymes such as cellulases and xylanases. Recombinant MnP (rMnP) can be produced in the yeast Pichia pastoris αMnP1-1 in fed-batch fermentations. The effects of pH and temperature on recombinant manganese peroxidase (rMnP) production by P. pastoris αMnP1-1 were investigated in shake flask and fed-batch fermentations. The optimum pH and temperature for a standardized fed-batch fermentation process for rMnP production in P. pastoris ctMnP1-1 were determined to be pH 6 and 30 °C, respectively. P. pastoris αMnP1-1 constitutively expresses the manganese peroxidase (mnp1) complementary DNA from Phanerochaete chrysosporium, and the rMnP has similar kinetic characteristics and pH activity and stability ranges as the wild-type MnP (wtMnP). Cultivation of P. chrysosporium mycelia in stationary flasks for production of heme peroxidases is commonly conducted at low pH (pH 4.2). However, shake flask and fed-batch fermentation experiments with P. pastoris αMnP1-1 demonstrated that rMnP production is highest at pH 6, with rMnP concentrations in the medium declining rapidly at pH less than 5.5, although cell growth rates were similar from pH 4-7. Investigations of the cause of low rMnP production at low pH were consistent with the hypothesis that intracellular proteases are released from dead and lysed yeast cells during the fermentation that are active against rMnP at pH less than 5.5.

  1. Laser driven thermal reactor for hazardous waste stabilization

    Energy Technology Data Exchange (ETDEWEB)

    Nazarian, A. [SAIC, Germantown, MD (United States)

    1996-12-31

    Increasing attention is being paid to treatment of hazardous waste through stabilization and possible solidification. Among the preferred technologies are thermal processes that detoxify and reduce the volume of hazardous wastes by exposing them to appropriate thermal regimes. However, as with any technology, there are potential problems which may detract from the application of the technology. Environmental pollution from particulate matter and off-gases can occur. Therefore, it is important to develop the technology of hazardous waste stabilization on a strong research base and to determine parameters and conditions of appropriate thermal processes. The purpose of the present work was to determine phenomenological parameters that characterize the processes of hazardous waste stabilization during thermal treatment. These methods can be used for any kind of liquid, solid and multiphase (liquid/solid and gas/solid) hazardous wastes. The method presented herein has been used to find corresponding parameters and conditions in the following applications: decomposition of ozone and nitrocompounds absorbed by activated carbon; sulphur compounds in heavy fuel oil; and appraisals of the explosion hazards involved in coal mining.

  2. Modifications to improve entrance slit thermal stability for grasshopper monochromators

    Science.gov (United States)

    Wallace, Daniel J.; Rogers, Gregory C.; Crossley, Sherry L.

    1994-08-01

    As new monochromators are designed for high-flux storage rings, computer modeling and thermal engineering can be done to process increased heat loads and achieve mechanical stability. Several older monochromators, such as the Mark 2 and Mark 5 Grasshopper monochromators, which were designed in 1974, have thermal instabilities in their entrance slit mechanisms. The Grasshoppers operating with narrow slits experience closure of the entrance slit from thermal expansion. In extreme cases, the thermal expansion of the precision components has caused permanent mechanical damage, leaving the slit uncalibrated and/or inoperable. For the Mark 2 and Mark 5 Grasshopper monochromators at the Synchrotron Radiation Center, the original 440 stainless steel entrance slit jaws were retrofitted with an Invar (low expansion Fe, Ni alloy) slit jaw. To transfer the heat from the critical components, two flexible heat straps of Cu were attached. These changes allow safe operation with a 10 μm entrance slit width where the previous limit was 30 μm. After an initial 2 min equilibration, the slit remains stable to 10%, with 100 mA of beam current. Additional improvements in slit thermal stability are planned for a third Grasshopper.

  3. Phenols and aromatic amines as thermal stabilizers in polyolefin processing

    Czech Academy of Sciences Publication Activity Database

    Pospíšil, Jan; Habicher, W. D.; Al-Malaika, S.; Zweifel, H.; Nešpůrek, Stanislav

    2001-01-01

    Roč. 176, - (2001), s. 55-63 ISSN 1022-1360. [International Conference on Polymer Modification, Degradation and Stabilization /1./. Palermo, 03.09.2000-07.09.2000] R&D Projects: GA AV ČR IAA1050901; GA MŠk ME 184; GA MŠk ME 372; GA AV ČR KSK4050111 Institutional research plan: CEZ:AV0Z4050913 Keywords : thermal stabilizers * phenols * aromatic amines Subject RIV: CD - Macromolecular Chemistry Impact factor: 0.634, year: 2001

  4. Structure and Thermal Stability of Copper Nitride Thin Films

    Directory of Open Access Journals (Sweden)

    Guangan Zhang

    2013-01-01

    Full Text Available Copper nitride (Cu3N thin films were deposited on glass via DC reactive magnetron sputtering at various N2 flow rates and partial pressures with 150°C substrate temperature. X-ray diffraction and scanning electron microscopy were used to characterize the microstructure and morphology. The results show that the films are composed of Cu3N crystallites with anti-ReO3 structure. The microstructure and morphology of the Cu3N film strongly depend on the N2 flow rate and partial pressure. The cross-sectional micrograph of the film shows typical columnar, compact structure. The thermal stabilities of the films were investigated using vacuum annealing under different temperature. The results show that the introducing of argon in the sputtering process decreases the thermal stability of the films.

  5. Thermal stability of charged rotating quantum black holes

    Science.gov (United States)

    Sinha, Aloke Kumar; Majumdar, Parthasarathi

    2017-12-01

    Criteria for thermal stability of charged rotating black holes of any dimension are derived for horizon areas that are large relative to the Planck area (in these dimensions). The derivation is based on generic assumptions of quantum geometry, supported by some results of loop quantum gravity, and equilibrium statistical mechanics of the Grand Canonical ensemble. There is no explicit use of classical spacetime geometry in this analysis. The only assumption is that the mass of the black hole is a function of its horizon area, charge and angular momentum. Our stability criteria are then tested in detail against specific classical black holes in spacetime dimensions 4 and 5, whose metrics provide us with explicit relations for the dependence of the mass on the charge and angular momentum of the black holes. This enables us to predict which of these black holes are expected to be thermally unstable under Hawking radiation.

  6. Thermal stability of black holes with arbitrary hairs

    Science.gov (United States)

    Sinha, Aloke Kumar

    2018-02-01

    We have derived the criteria for thermal stability of charged rotating black holes, for horizon areas that are large relative to the Planck area (in these dimensions). In this paper, we generalized it for black holes with arbitrary hairs. The derivation uses results of loop quantum gravity and equilibrium statistical mechanics of the grand canonical ensemble and there is no explicit use of classical spacetime geometry at all in this analysis. The assumption is that the mass of the black hole is a function of its horizon area and all the hairs. Our stability criteria are then tested in detail against some specific black holes, whose metrics provide us with explicit relations for the dependence of the mass on the area and other hairs of the black holes. This enables us to predict which of these black holes are expected to be thermally unstable under Hawking radiation.

  7. Production for high thermal stability NdFeB magnets

    Energy Technology Data Exchange (ETDEWEB)

    Yu, L.Q. [College of Physics Science and Technology, China University of Petroleum (East China), Dongying 257061, Shandong Province (China)], E-mail: iyy2000@163.com; Zhang, J.; Hu, S.Q.; Han, Z.D. [College of Physics Science and Technology, China University of Petroleum (East China), Dongying 257061, Shandong Province (China); Yan, M. [State Key Lab of Silicon Materials, Zhejiang University, Hangzhou 310027 (China)

    2008-04-15

    To improve sintered NdFeB magnets' thermal stability and magnetic properties, combined addition of elements Cu and Gd was investigated. It was found that with Gd addition increase to 1.0%, the temperature coefficient {alpha} improved from -0.15 to -0.05%/deg. C (maximum working temperature 120 deg. C), but the remanence and the maximum energy product linearly decreased. With addition of Cu in Gd-containing magnets the intrinsic coercivity increased greatly, and the remanence increased also because of their density improvement, and optimum Cu content was achieved at 0.2%. Microstructure analysis showed that most of the Cu distributed at grain boundaries and led to clear and smooth morphologies. Magnets with high thermal stability {alpha}=-0.05%/deg. C and magnetic properties were obtained with addition of Gd=0.8% and Cu=0.2%.

  8. Thermal stability of poly(3-hydroxybutyrate)/vegetable fiber composites

    Science.gov (United States)

    Cipriano, Pâmela Bento; de Sá, Mayelli Dantas; Andrade, André L. Simões; de Carvalho, Laura Hecker; Canedo, Eduardo Luis

    2015-05-01

    The present work deals with the thermal stability during and after processing of composites of poly(3-hydroxybutyrate) (PHB) - a fully biodegradable semi-crystalline thermoplastic obtained from renewable resources through low-impact biotechnological process, biocompatible and non-toxic - and vegetable fiber from the fruit (coconut) of babassu palm tree. PHB/babassu composites with 0, 5, 10 and 20% w/w load were prepared in a laboratory internal mixer. Two fractions of the mesocarp of babassu with different particle sizes were compounded with PHB and test specimens molded by compression. The effect of loading level and processing conditions on torque, temperature and mechanical energy dissipation were studied using a new engineering model. It was found that PHB degrades during processing at temperatures slightly above the melting point. To minimize thermal degradation stabilizer and chain extender additives were incorporated, with mixed results. These findings were confirmed by the dependence of the melt flow rate on the processing temperature.

  9. Thermal Stabilization of Enzymes Immobilized within Carbon Paste Electrodes.

    Science.gov (United States)

    Wang, J; Liu, J; Cepra, G

    1997-08-01

    In this note we report on the remarkable thermal stabilization of enzymes immobilized in carbon paste electrodes. Amperometric biosensors are shown for the first time to withstand a prolonged high-temperature (>50 °C) stress. Nearly full activity of glucose oxidase is retained over periods of up to 4 months of thermal stress at 60-80 °C. Dramatic improvements in the thermostability are observed for polyphenol oxidase, lactate oxidase, alcohol oxidase, horseradish peroxidase, and amino acid oxidase. Such resistance to heat-induced denaturation is attributed to the conformational rigidity of these biocatalysts within the highly hydrophobic (mineral oil or silicone grease) pasting liquid. While no chemical stabilizer is needed for attaining such protective action, it appears that low humidity (i.e., low water content) is essential for minimizing the protein mobility. Besides their implications for electrochemical biosensors, such observations should lead to a new generation of thermoresistant enzyme reactors based on nonpolar semisolid supports.

  10. Nanopore Event-Transduction Signal Stabilization for Wide pH Range under Extreme Chaotrope Conditions.

    Science.gov (United States)

    Winters-Hilt, Stephen; Stoyanov, Alexander

    2016-03-14

    Operation of an α-hemolysin nanopore transduction detector is found to be surprisingly robust over a critical range of pH (6-9), including physiological pH = 7.4 and polymerase chain reaction (PCR) pH = 8.4, and extreme chaotrope concentration, including 5 M urea. The engineered transducer molecule that is captured in the standard α-hemolysin nanopore detector, to transform it into a transduction detector, appears to play a central role in this stabilization process by stabilizing the channel against gating during its capture. This enables the nanopore transduction detector to operate as a single molecule "nanoscope" in a wide range of conditions, where tracking on molecular state is possible in a variety of different environmental conditions. In the case of streptavidin biosensing, results are shown for detector operation when in the presence of extreme (5 M) urea concentration. Complications involving degenerate states are encountered at higher chaotrope concentrations, but since the degeneracy is only of order two, this is easily absorbed into the classification task as in prior work. This allows useful detector operation over a wide range of conditions relevant to biochemistry, biomedical engineering, and biotechnology.

  11. Nanopore Event-Transduction Signal Stabilization for Wide pH Range under Extreme Chaotrope Conditions

    Directory of Open Access Journals (Sweden)

    Stephen Winters-Hilt

    2016-03-01

    Full Text Available Operation of an α-hemolysin nanopore transduction detector is found to be surprisingly robust over a critical range of pH (6–9, including physiological pH = 7.4 and polymerase chain reaction (PCR pH = 8.4, and extreme chaotrope concentration, including 5 M urea. The engineered transducer molecule that is captured in the standard α-hemolysin nanopore detector, to transform it into a transduction detector, appears to play a central role in this stabilization process by stabilizing the channel against gating during its capture. This enables the nanopore transduction detector to operate as a single molecule “nanoscope” in a wide range of conditions, where tracking on molecular state is possible in a variety of different environmental conditions. In the case of streptavidin biosensing, results are shown for detector operation when in the presence of extreme (5 M urea concentration. Complications involving degenerate states are encountered at higher chaotrope concentrations, but since the degeneracy is only of order two, this is easily absorbed into the classification task as in prior work. This allows useful detector operation over a wide range of conditions relevant to biochemistry, biomedical engineering, and biotechnology.

  12. Thermal Stability and Flammability of Polypropylene/Montmorillonite Composites

    Science.gov (United States)

    Yang, Ming-Shu; Qin, Huai-Li; Zhang, Shi-Min; Han, Charles C.

    2004-03-01

    Smectite clays, such as montmorillonite, are a valuable class of mineral for industrial applications because of their high aspect ratio, plate morphology, and intercalative capacity. After preparation, smectite clays may be used as a nano-scalled inorganic fillers to prepare polymer/layered silicate nanocomposites, which has unique properties such as improved strength, modulus, heat resistance, surface scratch resistance and good barrier properties, at very low filler. In the present work, polypropylene/montmorillonite (PP/MMT) composites were prepared and their thermal stability and flammability were investigated. Regardless of the micro-dispersed or submicro-dispersed structure, the composites exhibit higher thermal stability and considerably reduced peak heat release rate (PHRR). It is likely caused by the physical-chemical adsorption of the volatile degradation products on the silicates. On the other hand, the addition of MMT can catalyze the initial decomposition of PP matrix and accelerate the ignition of PP matrix in combustion. It has been observed that a ceramic-like char formed on the surface of the composites during burning test. The characterization of the char surface before ignition indicates that it is an inorganic-rich surface, which provided a better barrier property, leading to the improvement of the thermal stability and reduction of flammability of the composites.

  13. Thermal stability of segmented polyurethane elastomers reinforced by clay particles

    Directory of Open Access Journals (Sweden)

    Pavličević Jelena

    2009-01-01

    Full Text Available The aim of this work was to determine the influence of clay nanoparticles on thermal properties of segmented polyurethanes based on hexamethylene- diisocyanate, aliphatic polycarbonate diol and 1,4-butanediol as chain extender. The organically modified particles of montmorillonite and bentonite were used as reinforcing fillers. The structure of elastomeric materials was varied either by diol type or chain extender content. The ratio of OH groups from diol and chain extender (R was either 1 or 10. Thermal properties of prepared materials were determined using modulated differential scanning calorimetry (MDSC. Thermal stability of obtained elastomers has been studied by simultaneously thermogravimetry coupled with DSC. The glass transition temperature, Tg, of soft segments for all investigated samples was about -33°C. On the basis of DTG results, it was concluded that obtained materials were very stable up to 300°C.

  14. Thermal stability of detonation-produced micro and nanodiamonds

    Science.gov (United States)

    Efremov, V. P.; Zakatilova, E. I.; Maklashova, I. V.; Shevchenko, N. V.

    2018-01-01

    Detonation nanodiamonds are produced at utilization of high explosives. When an explosive blasts in a water environment, the detonation products contain microdiamonds, and in a gaseous medium, nanodiamonds. It is known that with decreasing size the influence of the surface energy of particles on their properties increases. Thus, it is interesting to compare the properties of detonation nano and microdiamonds. In this study, we have examined the thermal stability of diamond materials by synchronous thermal analysis. The experiments were performed at atmospheric pressure in argon flow for different heating rates in a range from room temperature to 1500 °C. Samples of initial and annealed micro and nanomaterials were studied using electron microscopy, x-ray and x-ray-fluorescence analysis. It was established that thermal and structural properties of micro and nanodiamonds differ substantially.

  15. Effects of Micro-environmental pH of Liposome on Chemical Stability of Loaded Drug.

    Science.gov (United States)

    Shao, Xiao-Ru; Wei, Xue-Qin; Zhang, Shu; Fu, Na; Lin, Yun-Feng; Cai, Xiao-Xiao; Peng, Qiang

    2017-08-23

    Liposome is a promising carrier system for delivering bioactive molecules. However, the successful delivery of pH-sensitive molecules is still limited by the intrinsic instability of payloads in physiological environment. Herein, we developed a special liposome system that possesses an acidic micro-environment in the internal aqueous chamber to improve the chemical stability of pH-sensitive payloads. Curcumin-loaded liposomes (Cur-LPs) with varied internal pH values (pH 2.5, 5.0, or 7.4) were prepared. These Cur-LPs have similar particle size of 300 nm, comparable physical stabilities and analogous in vitro release profiles. Interestingly, the chemical stability of liposomal curcumin in 50% fetal bovine serum and its anticancer efficacy in vitro are both micro-environmental pH-dependent (Cur-LP-2.5 > Cur-LP-5.0 > Cur-LP-7.4). This serum stability still has space to be further enhanced to improve the applicability of Cur-LP. In conclusion, creating an acidic micro-environment in the internal chamber of liposome is feasible and efficient to improve the chemical stability of pH-sensitive payloads.

  16. Increased stability of S-nitrosothiol solutions via pH modulations.

    Science.gov (United States)

    Hornyák, István; Marosi, Krisztina; Kiss, Levente; Gróf, Pál; Lacza, Zsombor

    2012-02-01

    S-nitrosothiol (RSNO) solutions represent a valuable source of nitric oxide and could be used as topical vasodilators, but their fast decomposition rate poses a serious obstacle to their potentially widespread therapeutic use. Our aim was to characterize and quantify the effect of pH on S-nitrosothiol formation and decomposition in simple aqueous solutions of S-nitrosoglutathione (GSNO), S-nitroso-N-acetylcysteine (SNAC) and S-nitroso-3-mercaptopropionic acid (SN3MPA). Furthermore, we investigated the effect of storage pH on the stability of GSNO incorporated in poly(ethylene glycol)/ poly(vinyl alcohol) matrices. S-nitrosothiol concentrations were measured spectrophotometrically and laser Doppler scanning method was used to assess dermal blood flow. GSH and NAC solutions reached a complete transformation to nitrosothiols when synthesized using acidic NaNO(2) solution. The initial concentration of all investigated RSNOs decreased more slowly with pH adjusted to mildly basic values (8.4-8.8) for the storage period. Polymer gels of PVA/PEG compositions at mildly basic storage pH further reduced the decomposition rate succeeding to contain 46.8% of the initial GSNO concentration for 25 days. This amount of topically administered GSNO was still capable of increasing the dermal blood flow over 200% in human subjects.

  17. Scandia-and-Yttria-Stabilized Zirconia for Thermal Barriers

    Science.gov (United States)

    Mess, Derek

    2003-01-01

    yttria in suitable proportions has shown promise of being a superior thermal- barrier coating (TBC) material, relative to zirconia stabilized with yttria only. More specifically, a range of compositions in the zirconia/scandia/yttria material system has been found to afford increased resistance to deleterious phase transformations at temperatures high enough to cause deterioration of yttria-stabilized zirconia. Yttria-stabilized zirconia TBCs have been applied to metallic substrates in gas turbine and jet engines to protect the substrates against high operating temperatures. These coatings have porous and microcracked structures, which can accommodate strains induced by thermal-expansion mismatch and thermal shock. The longevity of such a coating depends upon yttria as a stabilizing additive that helps to maintain the zirconia in an yttria-rich, socalled non-transformable tetragonal crystallographic phase, thus preventing transformation to the monoclinic phase with an associated deleterious volume change. However, at a temperature greater than about 1,200 C, there is sufficient atomic mobility that the equilibrium, transformable zirconia phase is formed. Upon subsequent cooling, this phase transforms to the monoclinic phase, with an associated volume change that adversely affects the integrity of the coating. Recently, scandia was identified as a stabilizer that could be used instead of, or in addition to, yttria. Of particular interest are scandia-and-yttria-stabilized zirconia (SYSZ) compositions of about 6 mole percent scandia and 1 mole percent yttria, which have been found to exhibit remarkable phase stability at a temperature of 1,400 C in simple aging tests. Unfortunately, scandia is expensive, so that the problem becomes one of determining whether there are compositions with smaller proportions of scandia that afford the required high-temperature stability. In an attempt to solve this problem, experiments were performed on specimens made with reduced

  18. Polyacetylene levels in carrot juice, effect of pH and thermal processing.

    Science.gov (United States)

    Aguiló-Aguayo, I; Brunton, N; Rai, D K; Balagueró, E; Hossain, M B; Valverde, J

    2014-01-01

    This research focuses on the study of polyacetylenes in carrot juice and their response to pH, storage and thermal processing conditions. Falcarindiol-3-acetate (FaDOAc) and falcarinol (FaOH) were in fresh carrot juice at concentrations of 73 and 233 μg/L, respectively. Reducing the pH of the raw carrot juice from its natural pH 6.13 to pH 3.5 resulted in 2 and 5 fold better extraction of FaDOAc and FaOH respectively in comparison to a control sample (pH 6.13). Polyacetylenes were retained better in acidified juices and cold storage temperatures (4 °C) for first week of storage with respect to untreated juices. An increase in FaDOAc and FaOH of 10- and 16-fold, respectively, as compared to raw unprocessed samples was observed when processing samples at 90 °C for 1 min. This was assumed to be due to cell wall polysaccharides dissolution. However, negative correlation between total polyacetylenes and hexoses was confirmed by (1)H NMR spectroscopy, indicating some biological links between polyacetylenes and soluble sugars. Copyright © 2013 Elsevier Ltd. All rights reserved.

  19. Solution and solid state thermal stability of morpholinedithiocarbamates

    Directory of Open Access Journals (Sweden)

    Antunes Patrícia A.

    2001-01-01

    Full Text Available Thermogravimetric and differential scanning calorimetric investigation of the thermal behavior of NH4+, Mn2+, Co2+, Ni2+ e Cu2+ morpholinedithiocarbamates were performed under nitrogen and air atmospheres in order to investigate the effect, in the thermal decomposition, of the presence of an oxygen as the heteroatom in the amine ring. Decomposition products were identified by their X-ray diffraction patterns. Metal sulfites and oxides were the major residues under nitrogen and air atmospheres, respectively. Spectrophotometric measurements were used to estimate the pKa =3.56 for the morpholinedithiocarbamic acid at 0.50 mol dm-3 ionic strength (NaClO4 at 25.0 °C and kinetic parameters of decomposition at different pH values (k lim = 0.14 ± 0.04 s-1 e t½ lim = 5.3 ± 1.2 s.

  20. A self-adaptive thermal switch array for rapid temperature stabilization under various thermal power inputs

    Science.gov (United States)

    Geng, Xiaobao; Patel, Pragnesh; Narain, Amitabh; Desheng Meng, Dennis

    2011-08-01

    A self-adaptive thermal switch array (TSA) based on actuation by low-melting-point alloy droplets is reported to stabilize the temperature of a heat-generating microelectromechanical system (MEMS) device at a predetermined range (i.e. the optimal working temperature of the device) with neither a control circuit nor electrical power consumption. When the temperature is below this range, the TSA stays off and works as a thermal insulator. Therefore, the MEMS device can quickly heat itself up to its optimal working temperature during startup. Once this temperature is reached, TSA is automatically turned on to increase the thermal conductance, working as an effective thermal spreader. As a result, the MEMS device tends to stay at its optimal working temperature without complex thermal management components and the associated parasitic power loss. A prototype TSA was fabricated and characterized to prove the concept. The stabilization temperatures under various power inputs have been studied both experimentally and theoretically. Under the increment of power input from 3.8 to 5.8 W, the temperature of the device increased only by 2.5 °C due to the stabilization effect of TSA.

  1. Swelling, Mechanics, and Thermal/Chemical Stability of Hydrogels Containing Phenylboronic Acid Side Chains

    Directory of Open Access Journals (Sweden)

    Arum Kim

    2017-12-01

    Full Text Available We report here studies of swelling, mechanics, and thermal stability of hydrogels consisting of 20 mol % methacrylamidophenylboronic acid (MPBA and 80 mol % acrylamide (AAm, lightly crosslinked with methylenebisacrylamide (Bis. Swelling was measured in solutions of fixed ionic strength, but with varying pH values and fructose concentrations. Mechanics was studied by compression and hold. In the absence of sugar or in the presence of fructose, the modulus was mostly maintained during the hold period, while a significant stress relaxation was seen in the presence of glucose, consistent with reversible, dynamic crosslinks provided by glucose, but not fructose. Thermal stability was determined by incubating hydrogels at pH 7.4 at room temperature, and 37, 50, and 65 °C, and monitoring swelling. In PBS (phosphate buffered saline solutions containing 9 mM fructose, swelling remained essentially complete for 50 days at room temperature, but decreased substantially with time at the higher temperatures, with accelerated reduction of swelling with increasing temperature. Controls indicated that over long time periods, both the MPBA and AAm units were experiencing conversion to different species.

  2. [Thermal inactivation and stabilization of lysozyme substrate-- Micrococcus lysodeicticus cells].

    Science.gov (United States)

    Tarun, E I; Eremin, A N; Metelitsa, D I

    1986-01-01

    Heat inactivation of the acetonic powder of Micrococcus lysodeicticus cells suspended in phosphate buffer pH 6.2 was quantitatively characterized in the temperature range from 34 to 52 degrees. The total value of the rate constant for heat inactivation of the cells equals 2.88 X 10(8) exp(-18360/RT) sec-1. The activation parameters of the process at 34 degrees are the following: delta H* = 17.7 kcal/mole; delta S* = 21.8 E. U.; delta F* = 24.4 kcal/mole. The effect of ethylene glycol, mannitol, dextran, polyvinyl alcohol (PVA) and polyethylene glycols with different molecular weights on the lysis rate and cell stability was studied. Polyvinyl alcohol was found to be the most effective stabilizer. At concentrations of about 10(-5) it enhances the thermostability of the cells threefold.

  3. Thermal stability of spent coffee ground polysaccharides: galactomannans and arabinogalactans.

    Science.gov (United States)

    Simões, Joana; Maricato, Elia; Nunes, Fernando M; Domingues, M Rosário; Coimbra, Manuel A

    2014-01-30

    In order to better understand the thermal stability of spent coffee grounds (SCG) galactomannans and arabinogalactans and the reactions that can occur upon roasting, long term isothermal exposures, up to 3h, were performed at 160, 180, 200, 220, and 240 °C. The resultant products were analysed according to the sugars and linkage composition and also by electrospray mass spectrometry. Galactomannans did not loss mass at T ≤ 200 °C during exposures up to 3h whereas the arabinogalactans showed that thermal stability only for T ≤ 180 °C. This was in accordance with the estimated activation energies of their thermal decomposition of 138 kJ/mol and 94 kJ/mol, respectively. The roasting of galactomannans promoted the formation of new glycosidic linkages, with occurrence of 2-, 6-, 2,3-, 2,6-, 3,6-, 2,3,6-, 3,4,6-linked mannose residues, 3,4,6-linked galactose residues, and terminally-linked glucose residues, observed by methylation analysis. Depolymerisation and formation of anhydrohexose residues at the reducing end and mannose-glucose isomerisation were also observed. The roasting of galactomannans at 200 °C promoted their solubility in water upon alkali extraction and neutralisation. Copyright © 2013 Elsevier Ltd. All rights reserved.

  4. Unusual thermal stability of nano-structured ferritic alloys

    International Nuclear Information System (INIS)

    Wang, X.L.; Liu, C.T.; Keiderling, U.; Stoica, A.D.; Yang, L.; Miller, M.K.; Fu, C.L.; Ma, D.; An, K.

    2012-01-01

    Highlights: ► A nanostructured steel is examined by in situ small angle neutron scattering and high-temperature neutron diffraction. ► A bi-modal particle size distribution is identified by small angle neutron scattering. ► The nanometer sized clusters are thermally stable up to 1400 °C. ► The microstructure of the material is stable at high-temperatures, with no evidence of recrystallization or grain growth. - Abstract: A scientific question vitally important to the materials community is whether there exist “self-assembled” nanoclusters that are thermodynamically stable at elevated temperatures. Using in situ neutron scattering, we have characterized the structure and thermal stability of a nano-structured ferritic alloy. Nanometer sized nanoclusters were found to persist up to ∼1400 °C, providing direct evidence of a thermodynamically stable alloying state for the nanoclusters. High-temperature neutron diffraction measurements show a stable ferritic matrix, with little evidence of recrystallization or grain growth at temperatures up to 1300 °C. This result suggests that thermally stable nanoclusters and the oxygen-vacancy interaction limit the diffusion of Fe atoms and hence the mobility of grain boundaries, stabilizing the microstructure of the ferritic matrix at high temperatures.

  5. Unusual thermal stability of nano-structured ferritic alloys

    Energy Technology Data Exchange (ETDEWEB)

    Wang, X.L., E-mail: wangxl@ornl.gov [Neutron Scattering Science Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Liu, C.T. [Materials Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Department of System Engineering and Engineering Management, City University of Hong Kong, 83 Tat Chee Avenue, Kowloon Tong (Hong Kong); Keiderling, U. [Helmholtz Center Berlin for Materials and Energy, Glienicker Strasse 100, D-14109 Berlin (Germany); Stoica, A.D.; Yang, L. [Neutron Scattering Science Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Miller, M.K.; Fu, C.L. [Materials Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Ma, D.; An, K. [Neutron Scattering Science Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States)

    2012-07-15

    Highlights: Black-Right-Pointing-Pointer A nanostructured steel is examined by in situ small angle neutron scattering and high-temperature neutron diffraction. Black-Right-Pointing-Pointer A bi-modal particle size distribution is identified by small angle neutron scattering. Black-Right-Pointing-Pointer The nanometer sized clusters are thermally stable up to 1400 Degree-Sign C. Black-Right-Pointing-Pointer The microstructure of the material is stable at high-temperatures, with no evidence of recrystallization or grain growth. - Abstract: A scientific question vitally important to the materials community is whether there exist 'self-assembled' nanoclusters that are thermodynamically stable at elevated temperatures. Using in situ neutron scattering, we have characterized the structure and thermal stability of a nano-structured ferritic alloy. Nanometer sized nanoclusters were found to persist up to {approx}1400 Degree-Sign C, providing direct evidence of a thermodynamically stable alloying state for the nanoclusters. High-temperature neutron diffraction measurements show a stable ferritic matrix, with little evidence of recrystallization or grain growth at temperatures up to 1300 Degree-Sign C. This result suggests that thermally stable nanoclusters and the oxygen-vacancy interaction limit the diffusion of Fe atoms and hence the mobility of grain boundaries, stabilizing the microstructure of the ferritic matrix at high temperatures.

  6. Grain boundary engineering to enhance thermal stability of electrodeposited nickel

    DEFF Research Database (Denmark)

    Alimadadi, Hossein

    Manufacturing technologies such as injection molding and micro electromechanical systems demand materials with improved mechanical properties (e.g. hardness, ductility) and high durability at elevated temperatures. Significant improvement in some of the mechanical properties is obtained by miniat......Manufacturing technologies such as injection molding and micro electromechanical systems demand materials with improved mechanical properties (e.g. hardness, ductility) and high durability at elevated temperatures. Significant improvement in some of the mechanical properties is obtained...... by miniaturization of the grains down to nano-meter scale. However, this augments the total grain boundary energy stored in the material, hence, making the material less thermally stable. Coherent twin boundaries are of very low energy and mobility compared to all other boundaries in a FCC material. Accordingly......, grain boundary engineering of electrodeposited nickel to achieve high population of coherent twin boundaries and, hence, higher thermal stability is a promising method to achieve simultaneous improvement in mechanical properties and thermal stability. This is of particular scientific and practical...

  7. A novel thermal and pH responsive drug delivery system based on ZnO@PNIPAM hybrid nanoparticles

    International Nuclear Information System (INIS)

    Tan, Licheng; Liu, Jian; Zhou, Weihua; Wei, Junchao; Peng, Zhiping

    2014-01-01

    A smart ZnO@PNIPAM hybrid was prepared by grafting thermal responsive poly(N-isopropylacrylamide) (PNIPAM) on zinc oxide (ZnO) nanoparticles via surface-initiated atom transfer radical polymerization (ATRP). The thermal gravimetric analysis (TGA) shows that the grafting amount of PNIPAM was about 38%, and the SEM images show that the PNIPAM chains can prevent the aggregation of ZnO nanoparticles. The responsive properties of ZnO@PNIPAM were measured by photoluminescence spectra, and the results demonstrate that the PNIPAM chains grafted on ZnO surfaces can realize reversible thermal responsive and photoluminescence properties. An anticancer drug, doxorubicin (Dox), was used as a model drug and loaded into the hybrid nanoparticles, and an in vitro drug release test implied that ZnO@PNIPAM could work as a thermal responsive drug delivery system. Furthermore, pH sensitive drug releases were carried out in acetate buffer at pH 5.0 and pH 6.0 and in water at pH 7.0, and the results showed evident pH dependency, showing its pH responsive properties. - Graphical abstract: In this manuscript, thermal responsive poly(N-isopropylacrylamide) (PNIPAM) was grafted on the surface of ZnO nanoparticles. The obtained ZnO@PNIPAM hybrid showed reversible thermal responsive photoluminescent properties, and can also work as a thermal and pH responsive drug delivery system. - Highlights: • The ZnO@PNIPAM hybrid was prepared via ATRP. • The ZnO@PNIPAM hybrid showed thermal responsive properties. • The ZnO@PNIPAM hybrid can work as a thermal and pH responsive drug delivery system

  8. A novel thermal and pH responsive drug delivery system based on ZnO@PNIPAM hybrid nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Tan, Licheng; Liu, Jian; Zhou, Weihua [Department of Chemistry, Nanchang University, Nanchang 330031 (China); Wei, Junchao, E-mail: weijunchao@ncu.edu.cn [Department of Chemistry, Nanchang University, Nanchang 330031 (China); State Key Laboratory of Molecular Engineering of Polymers, Department of Macromolecular Science, Fudan University, 220 Handan Road, Shanghai 200433 (China); Peng, Zhiping [Department of Chemistry, Nanchang University, Nanchang 330031 (China)

    2014-12-01

    A smart ZnO@PNIPAM hybrid was prepared by grafting thermal responsive poly(N-isopropylacrylamide) (PNIPAM) on zinc oxide (ZnO) nanoparticles via surface-initiated atom transfer radical polymerization (ATRP). The thermal gravimetric analysis (TGA) shows that the grafting amount of PNIPAM was about 38%, and the SEM images show that the PNIPAM chains can prevent the aggregation of ZnO nanoparticles. The responsive properties of ZnO@PNIPAM were measured by photoluminescence spectra, and the results demonstrate that the PNIPAM chains grafted on ZnO surfaces can realize reversible thermal responsive and photoluminescence properties. An anticancer drug, doxorubicin (Dox), was used as a model drug and loaded into the hybrid nanoparticles, and an in vitro drug release test implied that ZnO@PNIPAM could work as a thermal responsive drug delivery system. Furthermore, pH sensitive drug releases were carried out in acetate buffer at pH 5.0 and pH 6.0 and in water at pH 7.0, and the results showed evident pH dependency, showing its pH responsive properties. - Graphical abstract: In this manuscript, thermal responsive poly(N-isopropylacrylamide) (PNIPAM) was grafted on the surface of ZnO nanoparticles. The obtained ZnO@PNIPAM hybrid showed reversible thermal responsive photoluminescent properties, and can also work as a thermal and pH responsive drug delivery system. - Highlights: • The ZnO@PNIPAM hybrid was prepared via ATRP. • The ZnO@PNIPAM hybrid showed thermal responsive properties. • The ZnO@PNIPAM hybrid can work as a thermal and pH responsive drug delivery system.

  9. Enhancement of thermal stability of multiwalled carbon nanotubes via different silanization routes

    Energy Technology Data Exchange (ETDEWEB)

    Scheibe, B., E-mail: bscheibe@zut.edu.p [Centre of Knowledge Based Nanomaterials and Technologies, Institute of Chemical and Enviroment Engineering, West Pomeranian University of Technology, Szczecin (Poland); Borowiak-Palen, E.; Kalenczuk, R.J. [Centre of Knowledge Based Nanomaterials and Technologies, Institute of Chemical and Enviroment Engineering, West Pomeranian University of Technology, Szczecin (Poland)

    2010-06-18

    This work presents an effect of two different silanization procedures on thermal and structural properties of oxidized and oxidized followed by sodium borohydrate (NaBH{sub 4}) reduction of multiwalled carbon nanotubes (MWCNTs). Purified sample was oxidized in a mixture of nitric and sulfuric acids in a reflux. An oxidized material was divided into two batches. The first batch underwent a silanization procedure directly, while the second batch was reduced by NaBH{sub 4} treatment prior to the silanization. The silanization experiments were performed: (A) with {gamma}-aminopropyltriethoxysilane (APTES) at room temperature in acetone (pH {approx}7) and (B) with condensated {gamma}-aminopropyltriethoxysilane at 40 {sup o}C in water (pH 4). The extent of the functionalization of the samples after each procedure was examined by Raman spectroscopy. The vibrational properties of the materials were studied via Fourier transform infrared spectroscopy. Boehms titration technique was applied to quantify the amount of the functional groups on MWCNTs. The morphology of the pristine and functionalized carbon nanotubes was exposed to high-resolution transmission electron microscopy analysis. The energy dispersive X-ray (EDX) analysis was used to characterize the elemental composition of each sample. The effect of the silanization process on the thermal properties of MWCNTs was investigated by thermogravimetry analysis. Interestingly, the significant increase of the thermal stability of silanized MWCNTs samples in respect to the pristine MWCNTs was observed.

  10. Variation in Biofilm Stability with Decreasing pH Affects Porous Medium Hydraulic Properties

    Science.gov (United States)

    Kirk, M. F.; Santillan, E. F.; McGrath, L. K.; Altman, S. J.

    2010-12-01

    Changes to microbial communities caused by subsurface CO2 injection may have many consequences, including possible impacts to CO2 transport. We used column experiments to examine how decreasing pH, a geochemical change associated with CO2 injection, will affect biofilm stability and ultimately the hydraulic properties of porous media. Columns consisted of 1 mm2 square capillary tubes filled with 105-150 µm diameter glass beads. Artificial groundwater medium containing 1 mM glucose was pumped through the columns at a rate of 0.01 mL/min (q = 14.4 m/day; Re = 0.03). Columns were inoculated with 3 × 10^8 CFU (avg.) of Pseudomonas fluorescens, a model biofilm former, transformed with a green fluorescent protein. Biomass distribution and transport was examined using scanning laser confocal microscopy and effluent plating. Variation in the bulk hydraulic properties of the columns was measured using manometers. In an initial experiment, biofilm growth was allowed to occur for seven days in medium with pH 7.3. Within this period, cells uniformly coated bead surfaces, effluent cell numbers stabilized at 1 × 10^9 CFU/mL, and hydraulic conductivity (K) decreased 77%. Next, medium with pH 4 was introduced. As a result, biomass within the reactor redistributed from bead surfaces to pores, effluent cell numbers decreased to 3 × 10^5 CFU/mL, and K decreased even further (>94% reduction). This decreased K was maintained until the experiment was terminated, seven days after introducing low pH medium. These results suggest that changes in biomass distribution as a result of decreased pH may initially limit transport of solubility-trapped CO2 following CO2 injection. Experiments in progress and planned will test this result in more detail and over longer periods of time. This material is based upon work supported as part of the Center for Frontiers of Subsurface Energy Security, an Energy Frontier Research Center funded by the U.S. Department of Energy, Office of Science, Office

  11. Antioxidant-Based Phase-Change Thermal Interface Materials with High Thermal Stability

    Science.gov (United States)

    Aoyagi, Yasuhiro; Chung, D. D. L.

    2008-04-01

    This work provides phase-change thermal interface materials (TIMs) with high thermal stability and high heat of fusion. They are based on antioxidants mainly in the form of hydrocarbons with linear segments. The thermal stability is superior to paraffin wax and four commercial phase-change materials (PCMs). The use of 98.0 wt.% thiopropionate antioxidant (SUMILIZER TP-D) with 2.0 wt.% sterically half-hindered phenolic antioxidant (GA80) as the matrix and the use of 16 vol.% boron nitride particles as the solid component give a PCM with a 100°C lifetime indicator of 5.3 years, in contrast to 0.95 year or less for the commercial PCMs. The heat of fusion is much higher than those of commercial PCMs; the values for antioxidants with nonbranched molecular structures exceed that of wax; the value for one with a branched structure is slightly below that of wax. The phase-change properties are degraded by heating at 150°C much less than those of the commercial PCMs. The stability of the heat of fusion upon phase-change cycling is also superior. The viscosity is essentially unaffected by heating at 150°C. Commercial PCMs give slightly lower values of the thermal contact conductance for the case of rough (12 μm) mating surfaces, in spite of the lower values of the bond-line thickness.

  12. Bulk Nanolaminated Nickel: Preparation, Microstructure, Mechanical Property, and Thermal Stability

    Science.gov (United States)

    Liu, Fan; Yuan, Hao; Goel, Sunkulp; Liu, Ying; Wang, Jing Tao

    2018-02-01

    A bulk nanolaminated (NL) structure with distinctive fractions of low- and high-angle grain boundaries ( f LAGBs and f HAGBs) is produced in pure nickel, through a two-step process of primary grain refinement by equal-channel angular pressing (ECAP), followed by a secondary geometrical refinement via liquid nitrogen rolling (LNR). The lamellar boundary spacings of 2N and 4N nickel are refined to 40 and 70 nm, respectively, and the yield strength of the NL structure in 2N nickel reaches 1.5 GPa. The impacts of the deformation path, material purity, grain boundary (GB) misorientation, and energy on the microstructure, refinement ability, mechanical strength, and thermal stability are investigated to understand the inherent governing mechanisms. GB migration is the main restoration mechanism limiting the refinement of an NL structure in 4N nickel, while in 2N nickel, shear banding occurs and mediates one-fifth of the total true normal rolling strain at the mesoscale, restricting further refinement. Three typical structures [ultrafine grained (UFG), NL with low f LAGBs, and NL with high f LAGBs] obtained through three different combinations of ECAP and LNR were studied by isochronal annealing for 1 hour at temperatures ranging from 433 K to 973 K (160 °C to 700 °C). Higher thermal stability in the NL structure with high f LAGBs is shown by a 50 K (50 °C) delay in the initiation temperature of recrystallization. Based on calculations and analyses of the stored energies of deformed structures from strain distribution, as characterized by kernel average misorientation (KAM), and from GB misorientations, higher thermal stability is attributed to high f LAGBs in this type of NL structure. This is confirmed by a slower change in the microstructure, as revealed by characterizing its annealing kinetics using KAM maps.

  13. Organic transistors with high thermal stability for medical applications.

    Science.gov (United States)

    Kuribara, Kazunori; Wang, He; Uchiyama, Naoya; Fukuda, Kenjiro; Yokota, Tomoyuki; Zschieschang, Ute; Jaye, Cherno; Fischer, Daniel; Klauk, Hagen; Yamamoto, Tatsuya; Takimiya, Kazuo; Ikeda, Masaaki; Kuwabara, Hirokazu; Sekitani, Tsuyoshi; Loo, Yueh-Lin; Someya, Takao

    2012-03-06

    The excellent mechanical flexibility of organic electronic devices is expected to open up a range of new application opportunities in electronics, such as flexible displays, robotic sensors, and biological and medical electronic applications. However, one of the major remaining issues for organic devices is their instability, especially their thermal instability, because low melting temperatures and large thermal expansion coefficients of organic materials cause thermal degradation. Here we demonstrate the fabrication of flexible thin-film transistors with excellent thermal stability and their viability for biomedical sterilization processes. The organic thin-film transistors comprise a high-mobility organic semiconductor, dinaphtho[2,3-b:2',3'-f]thieno[3,2-b]thiophene, and thin gate dielectrics comprising a 2-nm-thick self-assembled monolayer and a 4-nm-thick aluminium oxide layer. The transistors exhibit a mobility of 1.2 cm(2) V(-1)s(-1) within a 2 V operation and are stable even after exposure to conditions typically used for medical sterilization.

  14. Thermal hydraulic stability in a pressure tube nuclear reactor

    International Nuclear Information System (INIS)

    Villani, A.; Ravetta, R.; Mansani, L.

    1986-01-01

    The CIRENE plant which will undergo preoperational tests in the near future is equipped with a 40 MW(e) Heavy Water moderated Boiling Light Water cooled Reactor (HWBLWR); at the start-up and up to about 30 % of nominal power, the necessary low coolant density is obtained injecting into the core a mixture of liquid and steam. To verify the thermal-hydraulic stability of the plant in this situation, tests have been carried out in a facility simulating two full scale power channels; the system stability has been confirmed in the reference conditions, and is not reduced by even a significant reduction of the liquid flowrate, where a decrease in liquid temperature has some negative effect and steam flowrate has a small influence. (author)

  15. Thermal stability for the effective use of commercial catalase

    Directory of Open Access Journals (Sweden)

    Miłek J.

    2014-12-01

    Full Text Available Catalase with the commercial catalase name Terminox Ultra is widely used in the textile industry in bleaching processes. This enzyme is used to catalyse the decomposition of residual hydrogen peroxide into oxygen and water. In this study catalase was kept for about 30 hours in water baths in a temperature range from 35 to 70°C. For the first time, the kinetics of thermal deactivation of this enzyme was examined using an oxygen electrode. Stability of the enzyme depends strongly on temperature and its half-life times are 0.0014 h and 7.6 h, at 35 and 70°C, respectively.

  16. Hardness and thermal stability of cubic silicon nitride

    DEFF Research Database (Denmark)

    Jiang, Jianzhong; Kragh, Flemming; Frost, D. J.

    2001-01-01

    The hardness and thermal stability of cubic spinel silicon nitride (c-Si3N4), synthesized under high-pressure and high-temperature conditions, have been studied by microindentation measurements, and x-ray powder diffraction and scanning electron microscopy, respectively The phase at ambient...... temperature has an average hardness of 35.31 GPa, slightly larger than SiO2 stishovite, which is often referred to as the third hardest material after diamond and cubic boron nitride. The cubic phase is stable up to 1673 K in air. At 1873 K, alpha -and beta -Si3N4 phases are observed, indicating a phase...

  17. BIOCHAR MODIFICATION, THERMAL STABILITY AND TOXICITY OF PRODUCTS MODIFICATION

    Directory of Open Access Journals (Sweden)

    Romana FRIEDRICHOVÁ

    2017-12-01

    Full Text Available Biochar is a product obtained from processing of waste biomass. The main application of biochar is in soil and environment remediation. Some new applications of this carbonaceous material take advantage of its adsorption capacity use it as a heterogeneous catalyst for energy storage and conversion etc. This contribution describes thermal stability of the original biochar. It discusses biochar modified by chemical and physical methods including a new compound of biochar-graphene oxide. The purpose of the modifications is to increase its active surface to introduce active functional groups into the carbon structure of biochar in relation to fire safety and toxicity of those products.

  18. Thermal stability of hard nanocomposite Mo-B-C coatings

    Czech Academy of Sciences Publication Activity Database

    Zábranský, L.; Buršíková, V.; Souček, P.; Vašina, P.; Dugáček, J.; Sťahel, P.; Buršík, Jiří; Svoboda, Milan; Peřina, V.; Peřina, Vratislav

    2017-01-01

    Roč. 138, APR (2017), s. 199-204 ISSN 0042-207X R&D Projects: GA ČR(CZ) GA15-17875S Institutional support: RVO:68081723 ; RVO:61389005 Keywords : thermal stability * Mo2BC coatings * hardness Subject RIV: JI - Composite Materials; JI - Composite Materials (UJF-V) OBOR OECD: Composites (including laminates, reinforced plastics, cermets, combined natural and synthetic fibre fabrics; Composites (including laminates, reinforced plastics, cermets, combined natural and synthetic fibre fabrics (UFM-A); Composites (including laminates, reinforced plastics, cermets, combined natural and synthetic fibre fabrics (UJF-V) Impact factor: 1.530, year: 2016

  19. High-temperature stability of yttria-stabilized zirconia thermal barrier ...

    Indian Academy of Sciences (India)

    Abstract. Thermal barrier coatings (TBCs) of yttria-stabilized zirconia (YSZ) of different thicknesses with an intermediate bond coat were deposited on C-103 Nb alloy using the air plasma spraying technique. The coatings were subjected to rapid infra-red (IR) heating (∼25◦C s−1) up to ∼1250◦C and exposed up to 100 s at ...

  20. Thermal stability and energy of deactivation of free and immobilized cellobiase

    Directory of Open Access Journals (Sweden)

    L.P.V. Calsavara

    2000-12-01

    Full Text Available Commercial cellobiase has been immobilized in controlled pore silica particles by covalent binding with the silane-glutaraldehyde method with protein and activity yields of 67% and 13.7%, respectively. Thermal stability of the free and immobilized enzyme (IE was determined with 0.2% w/v cellobiose solution, pH 4.8, temperatures from 40 to 70°C for free enzyme and 40 to 75°C for IE. Free cellobiase maintained its activity practically constant for 240 min at temperatures up to 55°C. The IE has shown higher stability retaining its activity in the same test up to 60° C. Half-lives for free enzyme were 14.1, 2.1 and 0.17 h at 60, 65 and 70°C, respectively, whereas the IE at the same temperatures had half-lives of 245, 21.3 and 2.9 h. The energy of thermal deactivation was 80.6 kcal/mol for the free enzyme and 85.2 kcal/mol for the IE, confirming stabilization by immobilization.

  1. Direct measurement of thermal stability of expressed CCR5 and stabilization by small molecule ligands.

    Science.gov (United States)

    Knepp, Adam M; Grunbeck, Amy; Banerjee, Sourabh; Sakmar, Thomas P; Huber, Thomas

    2011-02-01

    The inherent instability of heptahelical G protein-coupled receptors (GPCRs) during purification and reconstitution is a primary impediment to biophysical studies and to obtaining high-resolution crystal structures. New approaches to stabilizing receptors during purification and screening reconstitution procedures are needed. Here we report the development of a novel homogeneous time-resolved fluorescence assay (HTRF) to quantify properly folded CC-chemokine receptor 5 (CCR5). The assay permits high-throughput thermal stability measurements of femtomole quantities of CCR5 in detergent and in engineered nanoscale apolipoprotein-bound bilayer (NABB) particles. We show that recombinantly expressed CCR5 can be incorporated into NABB particles in high yield, resulting in greater thermal stability compared with that of CCR5 in a detergent solution. We also demonstrate that binding of CCR5 to the HIV-1 cellular entry inhibitors maraviroc, AD101, CMPD 167, and vicriviroc dramatically increases receptor stability. The HTRF assay technology reported here is applicable to other membrane proteins and could greatly facilitate structural studies of GPCRs.

  2. Thermal Stabilization study of polyacrylonitrile fiber obtained by extrusion

    Directory of Open Access Journals (Sweden)

    Robson Fleming Ribeiro

    2015-12-01

    Full Text Available A low cost and environmental friendly extrusion process of the Polyacrylonitrile (PAN polymer was viabilized by using the 1,2,3-propanetriol (glycerol as a plasticizer. The characterization of the fibers obtained by this process was the object of study in the present work. The PAN fibers were heat treated in the range of 200 °C to 300 °C, which is the temperature range related to the stabilization/oxidation step. This is a limiting phase during the carbon fiber processing. The characterization of the fibers was made using infrared spectroscopy, thermal analysis and microscopy. TGA revealed that the degradation of the extruded PAN co-VA fibers between 250 °C and 350 °C, corresponded to a 9% weight loss to samples analyzed under oxidizing atmosphere and 18% when the samples were analyzed under inert atmosphere. DSC showed that the exothermic reactions on the extruded PAN co-VA fibers under oxidizing synthetic air was broader and the cyclization started at a lower temperature compared under inert atmosphere. Furthermore, FT-IR analysis correlated with thermal anlysis showed that the stabilization/oxidation process of the extruded PAN fiber were coherent with other works that used PAN fibers obtained by other spinning processes.

  3. Preliminary hazards analysis of thermal scrap stabilization system. Revision 1

    International Nuclear Information System (INIS)

    Lewis, W.S.

    1994-01-01

    This preliminary analysis examined the HA-21I glovebox and its supporting systems for potential process hazards. Upon further analysis, the thermal stabilization system has been installed in gloveboxes HC-21A and HC-21C. The use of HC-21C and HC-21A simplified the initial safety analysis. In addition, these gloveboxes were cleaner and required less modification for operation than glovebox HA-21I. While this document refers to glovebox HA-21I for the hazards analysis performed, glovebox HC-21C is sufficiently similar that the following analysis is also valid for HC-21C. This hazards analysis document is being re-released as revision 1 to include the updated flowsheet document (Appendix C) and the updated design basis (Appendix D). The revised Process Flow Schematic has also been included (Appendix E). This Current revision incorporates the recommendations provided from the original hazards analysis as well. The System Design Description (SDD) has also been appended (Appendix H) to document the bases for Safety Classification of thermal stabilization equipment

  4. Pressure effects on the thermal stability of silicon carbide fibers

    Science.gov (United States)

    Jaskowiak, Martha H.; Dicarlo, James A.

    1989-01-01

    Commercially available polymer derived SiC fibers were treated at temperatures from 1000 to 2200 C in vacuum and argon gas pressure of 1 and 1360 atm. Effects of gas pressure on the thermal stability of the fibers were determined through property comparison between the pressure treated fibers and vacuum treated fibers. Investigation of the thermal stability included studies of the fiber microstructure, weight loss, grain growth, and tensile strength. The 1360 atm argon gas treatment was found to shift the onset of fiber weight loss from 1200 to above 1500 C. Grain growth and tensile strength degradation were correlated with weight loss and were thus also inhibited by high pressure treatments. Additional heat treatment in 1 atm argon of the fibers initially treated at 1360 atm argon caused further weight loss and tensile strength degradation, thus indicating that high pressure inert gas conditions would be effective only in delaying fiber strength degradation. However, if the high gas pressure could be maintained throughout composite fabrication, then the composites could be processed at higher temperatures.

  5. Thermal stability and modeling of lithium ion batteries

    Science.gov (United States)

    Botte, Gerardine Gabriela

    2000-10-01

    First-principles mathematical models were developed to examine the effect of the lithium-lithium ion interactions inside the anode particles on the performance of a lithium foil cell. Two different models were developed: the chemical potential model (CPM) that includes the lithium-lithium ion interactions inside the anode particles and the diffusion model (DIM) that does not include the interactions. Significant differences in the thermal and electrochemical performance of the cell were observed between the two approaches. The temperature of the cell predicted by the DFM is higher than the one predicted by the CPM at a given capacity. The discharge time of the cell predicted by the DFM is shorter than the one predicted by the CPM. The results indicate that the cell needs to be modeled using the CPM approach especially at high discharge rates. An evaluation of the numerical techniques, control volume formulation (CVF) and finite difference method (FDM), used for the models was performed. It is shown that the truncation error is the same for both methods when the boundary conditions are of the Dirichlet type, the system of equations are linear and represented in Cartesian coordinates. A new technique to analyze the accuracy of the methods is presented. The only disadvantage of the FDM is that it failed to conserve mass for a small number of nodes when both boundary conditions include a derivative term whereas the CVF did conserve mass for these cases. However, for a large number of nodes the FDM provides mass conservation. It is important to note that the CVF has only (DeltaX) order of accuracy for a Neumann type boundary condition whereas the FDM has (DeltaX) 2 order. The second topic of this dissertation presents a study of the thermal stability of LiPF6 EC:EMC electrolyte for lithium ion batteries. A differential scanning calorimeter (DSC) was used to perform the study of the electrolyte. For first time, the effect of different variables on its thermal stability

  6. Contribution to the study of superconductor thermal stability

    International Nuclear Information System (INIS)

    Meuris, Chantal.

    1982-06-01

    The fundamental problem consists in ensuring, a priori, that transitions from the superconducting state to the normal resistive state, created by thermal disturbances, resorb spontaneously. An analysis of the validity limits of the criteria generally used leads to the definition of a certain number of unsolved problems raised by two particular configurations linked to the present technology of large superconducting magnets. The thermal stability is studied in relation to disturbances leading to a dispersion of heat in the conductor. The first configuration is representative of that of magnets with cooling channels defined transversely to the conductor and communicating with the main helium source (for example toroidal coil of Tore Supra). The uneven distribution of coolant along the conductor, due to the presence of the insulating supports marking the channels, leads to possible states for the conductor which were not anticipated till now. A theoretical study is developed of the stable and unstable stationary states of the conductor and the respective attraction fields of the stable states. A complete digital analysis of the dynamics of the state of the disturbed system is then made. This digital simulation is compared with the experimental results. The second configuration relates to the case of a conductor cooled by a limited volume of superfluid helium, for example a cable with internal cooling by static superfluid helium. An analysis of the cooling medium enables a theoretical relation to be established between the usable enthalpy and the time distribution of the thermal disturbance. This culminates in a fresh stability and dimensioning criterion of the cooling system with respect to the type of disturbances. An experimental study confirms this theory [fr

  7. Thermal stability of germanium-tin (GeSn) fins

    Science.gov (United States)

    Lei, Dian; Lee, Kwang Hong; Bao, Shuyu; Wang, Wei; Masudy-Panah, Saeid; Tan, Chuan Seng; Tok, Eng Soon; Gong, Xiao; Yeo, Yee-Chia

    2017-12-01

    We investigate the thermal stability of germanium-tin (Ge1-xSnx) fins under rapid thermal annealing in N2 ambient. The Ge1-xSnx fins were formed on a GeSn-on-insulator substrate and were found to be less thermally stable than blanket Ge1-xSnx films. The morphology change and material quality of the annealed Ge1-xSnx fin are investigated using scanning electron microscopy, Raman spectroscopy, high-resolution transmission electron microscopy, energy-dispersive X-ray spectroscopy, and electron energy loss spectroscopy. Obvious degradation of crystalline quality of the Ge0.96Sn0.04 fin was observed, and a thin Ge layer was formed on the SiO2 surface near the Ge0.96Sn0.04 fin region after 500 °C anneal. A model was proposed to explain the morphology change of the Ge0.96Sn0.04 fin.

  8. Thermal stability studies of diamond-like carbon films

    Energy Technology Data Exchange (ETDEWEB)

    Parmeter, J.E.; Tallant, D.R.; Siegal, M.P.

    1994-04-01

    Thin films of amorphous carbon/hydrogen, also known as diamond-like carbon or DLC, are of interest as an economical alternative to diamond in a variety of coatings applications. We have investigated the thermal stability of DLC films deposited onto tungsten and aluminum substrates via plasma CVD of methane. These films contain approximately 40 atom % hydrogen, and based on Auger spectra the carbon in the films is estimated to be 60% sp{sup 3} hybridized and 40% sp{sup 2} hybridized. Thermal desorption, Auger, and Raman measurements all indicate that the DLC films are stable to 250--300C. Between 300 and 500C, thermal evolution of hydrogen from the films is accompanied by the conversion of carbon from sp{sup 3} to sp{sup 2} hybridization, and Raman spectra indicate the conversion of the overall film structure from DLC to micro-crystalline graphite or so called ``glassy`` carbon. These results suggest that DLC of this type is potentially useful for applications in which the temperature does not exceed 250C.

  9. Thermal Stability Threshold for Amyloid Formation in Light Chain Amyloidosis

    Directory of Open Access Journals (Sweden)

    Tanya L. Poshusta

    2013-11-01

    Full Text Available Light chain (AL amyloidosis is a devastating disease characterized by amyloid deposits formed by immunoglobulin light chains. Current available treatments involve conventional chemotherapy and autologous stem cell transplant. We have recently concluded a phase III trial comparing these two treatments. AL amyloidosis patients who achieve hematological complete response (CR do not necessarily achieve organ response regardless of the treatment they received. In order to investigate the possible correlation between amyloid formation kinetics and organ response, we selected AL amyloidosis patients from the trial with kidney involvement and CR after treatment. Six patients were selected and their monoclonal immunoglobulin light chains were characterized. The proteins showed differences in their stability and their kinetics of amyloid formation. A correlation was detected at pH 7.4, showing that less stable proteins are more likely to form amyloid fibrils. AL-T03 is too unstable to form amyloid fibrils at pH 7.4. This protein was found in the only patient in the study that had organ response, suggesting that partially folded species are required for amyloid formation to occur in AL amyloidosis.

  10. Studies on thermal properties and thermal control effectiveness of a new shape-stabilized phase change material with high thermal conductivity

    International Nuclear Information System (INIS)

    Cheng Wenlong; Liu Na; Wu Wanfan

    2012-01-01

    In order to overcome the difficulty of conventional phase change materials (PCMs) in packaging, the shape-stabilized PCMs are proposed to be used in the electronic device thermal control. However, the conventional shape-stabilized PCMs have the drawback of lower thermal conductivity, so a new shape-stabilized PCM with high thermal conductivity, which is suitable for thermal control of electronic devices, is prepared. The thermal properties of n-octadecane-based shape-stabilized PCM are tested and analyzed. The heat storage/release performance is studied by numerical simulation. Its thermal control effect for electronic devices is also discussed. The results show that the expanded graphite (EG) can greatly improve the thermal conductivity of the material with little effect on latent heat and phase change temperature. When the mass fraction of EG is 5%, thermal conductivity has reached 1.76 W/(m K), which is over 4 times than that of the original one. Moreover, the material has larger latent heat and good thermal stability. The simulation results show that the material can have good heat storage/release performance. The analysis of the effect of thermal parameters on thermal control effect for electronic devices provides references to the design of phase change thermal control unit. - Highlights: ► A new shape-stabilized PCM with higher thermal conductivity is prepared. ► The material overcomes the packaging difficulty of traditional PCMs used in thermal control unit. ► The EG greatly improves thermal conductivity with little effect on latent heat. ► The material has high thermal stability and good heat storage/release performance. ► The effectiveness of the material for electronic device thermal control is proved.

  11. Effect of pH on stability constants of Am(III)- and Cm(III)- humate complexes

    International Nuclear Information System (INIS)

    Samadfam, Mohammad; Jintoku, Takashi; Sato, Seichi; Ohashi, Hiroshi; Mitsugashira, Toshiaki; Hara, Mitsuo; Suzuki, Yoshimitsu

    1999-01-01

    The apparent stability constants of Am(III)- and Cm(III)-humate complexes were determined by dialysis method at ionic strength 0.1 in the pH range from 3.3 to 5.7 under N 2 bubbling. The Am(III) and Cm(III) loadings were about 10 -7 and 10 -10 mol/dm 3 . The concentrations of Am-241 and Cm-242 tracers were measured by α-spectrometry. It was found that the apparent stability constants were almost identical for both the Am(III)-humate and Cm(III)-humate complexes. The apparent stability constants showed a small pH-dependence, increasing from 10 4.6 at pH 3.3 to 10 5.1 at pH 5.7. The ionization of acidic functional groups of humic acid is possibly the primary factor. Above pH 6, the dialysis membrane was no langer permeable to Am(III) and Cm(III) ions and the apparent stability constant could not be experimentally obtained. The apparent stability constants between pH 6 and pH 8.5 were evaluated by considering that both binary metal-humate and ternary metal-hydroxo-humate complexes exist at pHs above 6. It was assumed that mono-hydroxo-humate complex Am(OH)HA and Cm(OH)HA are the major ternary complexes that exist below pH 9. The overall stability constants for Am(III)- and Cm(III)-humate complexes increased from 10 5.7 at pH 6 to 10 7.2 at pH 8. This implies that the formation of metal-hydroxo-humate species is preferred over the formation of hydroxide species. The apparent overall stability constants can be easily incorporated into geochemical modeling of trivalent actinide migration. The results of the present study show that the apparent stability constants determined experimentally at pH≤6 do not represent the complexation properties at higher pHs and the formation of ternary complexes should be considered in speciation calculations of radionuclides at terrestrial environment. (J.P.N.)

  12. Effects of pH on the stability of cyanidin and cyanidin 3-O-β-glucopyranoside in aqueous solution

    Directory of Open Access Journals (Sweden)

    Rakić Violeta P.

    2015-01-01

    Full Text Available The colour variation, colour intensity and stability at various pH values (2.0, 4.0, 7.0 and 9.0 of cyanidin 3-O-β-glucopyranoside (Cy3Glc and its aglycone cyanidin was investigated during a period of 8 hours storage at 25ºC. Our data showed that pH of aqueous solution had impact on spectroscopic profile of cyanidin and Cy3Glc. Beginning with the most acidic solutions, increasing the pH induce bathochromic shifts of absorbance maximum in the visible range for all examined pH values (with the exception pH 4.0 for cyanidin, while the presence of the 3-glucosidic substitution induce hypsochromic shift. Compared to cyanidin, Cy3Glc has higher colour intensity and higher stability in the whole pH range, except at pH 7.0. The 3-glucosidic substitution influences on the colour intensity of Cy3Glc in the alkaline region. After 8-hour incubation of Cy3Glc and cyanidin at pH 2.0 and 25 ºC, 99% of Cy3Glc and only 27% of cyanidin remained unchanged.

  13. Thermal stability and thermal conductivity of phosphorene in phosphorene/graphene van der Waals heterostructures.

    Science.gov (United States)

    Pei, Qing-Xiang; Zhang, Xiaoliang; Ding, Zhiwei; Zhang, Ying-Yan; Zhang, Yong-Wei

    2017-07-14

    Phosphorene, a new two-dimensional (2D) semiconducting material, has attracted tremendous attention recently. However, its structural instability under ambient conditions poses a great challenge to its practical applications. A possible solution for this problem is to encapsulate phosphorene with more stable 2D materials, such as graphene, forming van der Waals heterostructures. In this study, using molecular dynamics simulations, we show that the thermal stability of phosphorene in phosphorene/graphene heterostructures can be enhanced significantly. By sandwiching phosphorene between two graphene sheets, its thermally stable temperature is increased by 150 K. We further study the thermal transport properties of phosphorene and find surprisingly that the in-plane thermal conductivity of phosphorene in phosphorene/graphene heterostructures is much higher than that of the free-standing one, with a net increase of 20-60%. This surprising increase in thermal conductivity arises from the increase in phonon group velocity and the extremely strong phonon coupling between phosphorene and the graphene substrate. Our findings have an important meaning for the practical applications of phosphorene in nanodevices.

  14. Increasing Type 1 Poliovirus Capsid Stability by Thermal Selection

    Science.gov (United States)

    Adeyemi, Oluwapelumi O.; Nicol, Clare

    2016-01-01

    ABSTRACT Poliomyelitis is a highly infectious disease caused by poliovirus (PV). It can result in paralysis and may be fatal. Integrated global immunization programs using live-attenuated oral (OPV) and/or inactivated (IPV) PV vaccines have systematically reduced its spread and paved the way for eradication. Immunization will continue posteradication to ensure against reintroduction of the disease, but there are biosafety concerns for both OPV and IPV. They could be addressed by the production and use of virus-free virus-like particle (VLP) vaccines that mimic the “empty” capsids (ECs) normally produced in viral infection. Although ECs are antigenically indistinguishable from mature virus particles, they are less stable and readily convert into an alternative conformation unsuitable for vaccine purposes. Stabilized ECs, expressed recombinantly as VLPs, could be ideal candidate vaccines for a polio-free world. However, although genome-free PV ECs have been expressed as VLPs in a variety of systems, their inherent antigenic instability has proved a barrier to further development. In this study, we selected thermally stable ECs of type 1 PV (PV-1). The ECs are antigenically stable at temperatures above the conversion temperature of wild-type (wt) virions. We have identified mutations on the capsid surface and in internal networks that are responsible for EC stability. With reference to the capsid structure, we speculate on the roles of these residues in capsid stability and postulate that such stabilized VLPs could be used as novel vaccines. IMPORTANCE Poliomyelitis is a highly infectious disease caused by PV and is on the verge of eradication. There are biosafety concerns about reintroduction of the disease from current vaccines that require live virus for production. Recombinantly expressed virus-like particles (VLPs) could address these inherent problems. However, the genome-free capsids (ECs) of wt PV are unstable and readily change antigenicity to a form not

  15. Thermal stability for a reactive viscous flow in a slab

    CERN Document Server

    Okoya, S S

    2002-01-01

    The paper deals with the effect of dimensionless non - Newtonian coefficient on the thermal stability of a reactive viscous liquid in steady flow between parallel heated plates. It is assumed that the liquid is symmetrically heated and the flow fully developed. Approximate analytical solution is obtained for the velocity of the flow and the criterion for which this solution is valid is determined. After the velocity distribution is known, the temperature distribution may be calculated. Criticality and disappearance of criticality (transition values) are obtained in the following cases: (i) Bimolecular (ii) Arrhenius and (iii) Sensitized temperature dependence. We have observed that nonlinear effect from velocity and temperature fields introduced decaying for the transitional values of the dimensionless central temperature. Other effects of this nonlinearity are reported. We also give results for the plane - Couette flow problem. The results help to enhance understanding of the interplay between Newtonian and ...

  16. High stability of self-assembled peptide nanowires against thermal, chemical, and proteolytic attacks.

    Science.gov (United States)

    Ryu, Jungki; Park, Chan Beum

    2010-02-01

    Understanding the self-assembly of peptides into ordered nanostructures is recently getting much attention since it can provide an alternative route for fabricating novel bio-inspired materials. In order to realize the potential of the peptide-based nanofabrication technology, however, more information is needed regarding the integrity or stability of peptide nanostructures under the process conditions encountered in their applications. In this study, we investigated the stability of self-assembled peptide nanowires (PNWs) and nanotubes (PNTs) against thermal, chemical, proteolytic attacks, and their conformational changes upon heat treatment. PNWs and PNTs were grown by the self-assembly of diphenylalanine (Phe-Phe), a peptide building block, on solid substrates at different chemical atmospheres and temperatures. The incubation of diphenylalanine under aniline vapor at 150 degrees C led to the formation of PNWs, while its incubation with water vapor at 25 degrees C produced PNTs. We analyzed the stability of peptide nanostructures using multiple tools, such as electron microscopy, thermal analysis tools, circular dichroism, and Fourier-transform infrared spectroscopy. Our results show that PNWs are highly stable up to 200 degrees C and remain unchanged when incubated in aqueous solutions (from pH 1 to 14) or in various chemical solvents (from polar to non-polar). In contrast, PNTs started to disintegrate even at 100 degrees C and underwent a conformational change at an elevated temperature. When we further studied their resistance to a proteolytic environment, we discovered that PNWs kept their initial structure while PNTs fully disintegrated. We found that the high stability of PNWs originates from their predominant beta-sheet conformation and the conformational change of diphenylalanine nanostructures. Our study suggests that self-assembled PNWs are suitable for future nano-scale applications requiring harsh processing conditions. 2009 Wiley Periodicals, Inc.

  17. Novel polypyrrole films with excellent crystallinity and good thermal stability

    International Nuclear Information System (INIS)

    Jeeju, Pullarkat P.; Varma, Sreekanth J.; Francis Xavier, Puthampadath A.; Sajimol, Augustine M.; Jayalekshmi, Sankaran

    2012-01-01

    Polypyrrole has drawn a lot of interest due to its high thermal and environmental stability in addition to high electrical conductivity. The present work highlights the enhanced crystallinity of polypyrrole films prepared from the redoped sample solution. Initially hydrochloric acid doped polypyrrole was prepared by chemical oxidative polymerization of pyrrole using ammonium peroxidisulphate as oxidant. The doped polypyrrole was dedoped using ammonia solution and then redoped with camphor sulphonic acid. Films were coated on ultrasonically cleaned glass substrates from the redoped sample solution in meta-cresol. The enhanced crystallinity of the polypyrrole films has been established from X-ray diffraction (XRD) studies. The room temperature electrical conductivity of the redoped polypyrrole film is about 30 times higher than that of the hydrochloric acid doped pellet sample. The results of Raman spectroscopy, Differential scanning calorimetry (DSC) and Thermogravimetric analysis (TGA) of the samples support the enhancement in crystallinity. Percentage crystallinity of the samples is estimated from XRD and DSC data. The present work is significant, since crystallinity of films is an important parameter for selecting polymers for specific applications. - Highlights: ► Polypyrrole films redoped with CSA have been prepared from meta-cresol solution. ► The solution casted films exhibit semi-crystallinity and good thermal stability. ► Percentage crystallinity estimated using XRD and DSC analysis is about 65%. ► Raman studies support the enhancement in crystallinity based on XRD and DSC data. ► The conductivity of the film is 30 times higher than that of HCl doped sample.

  18. Novel polypyrrole films with excellent crystallinity and good thermal stability

    Energy Technology Data Exchange (ETDEWEB)

    Jeeju, Pullarkat P., E-mail: jeejupp@gmail.com [Division for Research in Advanced Materials, Department of Physics, Cochin University of Science and Technology, Cochin-22, Kerala (India); Varma, Sreekanth J.; Francis Xavier, Puthampadath A.; Sajimol, Augustine M. [Division for Research in Advanced Materials, Department of Physics, Cochin University of Science and Technology, Cochin-22, Kerala (India); Jayalekshmi, Sankaran, E-mail: jayalekshmi@cusat.ac.in [Division for Research in Advanced Materials, Department of Physics, Cochin University of Science and Technology, Cochin-22, Kerala (India)

    2012-06-15

    Polypyrrole has drawn a lot of interest due to its high thermal and environmental stability in addition to high electrical conductivity. The present work highlights the enhanced crystallinity of polypyrrole films prepared from the redoped sample solution. Initially hydrochloric acid doped polypyrrole was prepared by chemical oxidative polymerization of pyrrole using ammonium peroxidisulphate as oxidant. The doped polypyrrole was dedoped using ammonia solution and then redoped with camphor sulphonic acid. Films were coated on ultrasonically cleaned glass substrates from the redoped sample solution in meta-cresol. The enhanced crystallinity of the polypyrrole films has been established from X-ray diffraction (XRD) studies. The room temperature electrical conductivity of the redoped polypyrrole film is about 30 times higher than that of the hydrochloric acid doped pellet sample. The results of Raman spectroscopy, Differential scanning calorimetry (DSC) and Thermogravimetric analysis (TGA) of the samples support the enhancement in crystallinity. Percentage crystallinity of the samples is estimated from XRD and DSC data. The present work is significant, since crystallinity of films is an important parameter for selecting polymers for specific applications. - Highlights: Black-Right-Pointing-Pointer Polypyrrole films redoped with CSA have been prepared from meta-cresol solution. Black-Right-Pointing-Pointer The solution casted films exhibit semi-crystallinity and good thermal stability. Black-Right-Pointing-Pointer Percentage crystallinity estimated using XRD and DSC analysis is about 65%. Black-Right-Pointing-Pointer Raman studies support the enhancement in crystallinity based on XRD and DSC data. Black-Right-Pointing-Pointer The conductivity of the film is 30 times higher than that of HCl doped sample.

  19. Study on the effect of shape-stabilized phase change materials on spacecraft thermal control in extreme thermal environment

    International Nuclear Information System (INIS)

    Wu, Wan-fan; Liu, Na; Cheng, Wen-long; Liu, Yi

    2013-01-01

    Highlights: ► A shape-stabilized PCM is used to protect the spacecraft attacked by high energy. ► Taking a satellite as example, it proves the solution given in the work is feasible. ► Low thermal conductivity makes the material above its thermal stability limit. ► It provides guidance on how to choose the shape-stabilized PCM for similar problems. - Abstract: In space, the emergencies such as short-term high heat flux is prone to cause spacecraft thermal control system faults, resulting in temperature anomalies of electronic equipment of the spacecraft and even failures in them. In order to protect the spacecraft attacked by the high energy, a new guard method is proposed. A shape-stabilized phase change material (PCM), which has high thermal conductivity and does not require being tightly packaged, is proposed to be used on the spacecraft. To prove the feasibility of using the material on spacecraft attacked by high energy, the thermal responses for spacecraft with shape-stabilized PCM are investigated in situations of normal and short-term high heat flux, in contrast to that with conventional thermal control system. The results indicate that the shape-stabilized PCM can effectively absorb the heat to prevent the thermal control system faults when the spacecraft’s outer heat flux changes dramatically and has no negative effect on spacecraft in normal heat flux. Additionally the effect of thermal conductivity of PCM on its application effectiveness is discussed

  20. Stability of white wine proteins: combined effect of pH, ionic strength, and temperature on their aggregation.

    Science.gov (United States)

    Dufrechou, Marie; Poncet-Legrand, Céline; Sauvage, François-Xavier; Vernhet, Aude

    2012-02-08

    Protein haze development in white wines is an unacceptable visual defect attributed to slow protein unfolding and aggregation. It is favored by wine exposure to excessive temperatures but can also develop in properly stored wines. In this study, the combined impact of pH (2.5-4.0), ionic strength (0.02-0.15 M), and temperature (25, 40, and 70 °C) on wine protein stability was investigated. The results showed three classes of proteins with low conformational stability involved in aggregation at room temperature: β-glucanases, chitinases, and some thaumatin-like protein isoforms (22-24 kDa). Unexpectedly, at 25 °C, maximum instability was observed at the lower pH, far from the protein isoelectric point. Increasing temperatures led to a shift of the maximum haze at higher pH. These different behaviors could be explained by the opposite impact of pH on intramolecular (conformational stability) and intermolecular (colloidal stability) electrostatic interactions. The present results highlight that wine pH and ionic strength play a determinant part in aggregation mechanisms, aggregate characteristics, and final haze.

  1. Thermal stability and practical applications of UV induced index changes in silica glasses

    DEFF Research Database (Denmark)

    Rathje, Jacob

    2000-01-01

    This thesis represents the partial fulfilment of the requirements for the danish ph.d. degree. I have been involved in both basic research of UV induced refractive index changes in silica glasses and in concrete applications. I have performed work on the thermal stability of UV-induced index...... fibers two separate engergy distributions are resolved indicating that two different defect types are present. The influence of core concentricity error on the asymmetric directional bend induced resonance splitting of a long period fiber grating was investigated. A qualitiative model to describe...... the asymmetry showed good agreement with the obeserved data. The results were used to make a direction sensitive bend sensor of only one fiber. The sensor has further the advantage that it is insensitve to cross sensitivity from temperature, strin, and other external factors. Finally, an investigation of Nragg...

  2. Thermal Stability and Material Balance of Nanomaterials in Waste Incineration

    Science.gov (United States)

    Paur, H.-R.; Baumann, W.; Hauser, M.; Lang, I.; Teuscher, N.; Seifert, H.; Stapf, D.

    2017-06-01

    Nanostructured materials are widely used to improve the properties of consumer products such as tires, cosmetics, light weight equipment etc. Due to their complex composition these products are hardly recycled and thermal treatment is preferred. In this study we investigated the thermal stability and material balance of nanostructured metal oxides in flames and in an industrial waste incinerator. We studied the size distribution of nanostructured metal oxides (CeO2, TiO2, SiO2) in a flame reactor and in a heated reaction tube. In the premixed ethylene/air flame, nano-structured CeO2 partly evaporates forming a new particle mode. This is probably due to chemical reactions in the flame. In addition sintering of agglomerates takes place in the flame. In the electrically heated reaction tube however only sintering of the agglomerated nanomaterials is observed. Ceria has a low background in waste incinerators and is therefore a suitable tracer for investigating the fate of nanostructured materials. Low concentrations of Ceria were introduced by a two-phase nozzle into the post-combustion zone of a waste incinerator. By the incineration of coal dust in a burning chamber the Ceria nanoparticles are mainly found in the size range of the fly ash (1 - 10 µm) because of agglomeration. With gas as a fuel less agglomeration was observed and the Ceria nanoparticles were in the particle size range below 1 µm.

  3. Thermal Stability and Material Balance of Nanomaterials in Waste Incineration

    International Nuclear Information System (INIS)

    Paur, H.-R.; Baumann, W.; Hauser, M.; Lang, I.; Teuscher, N.; Seifert, H.; Stapf, D.

    2017-01-01

    Nanostructured materials are widely used to improve the properties of consumer products such as tires, cosmetics, light weight equipment etc. Due to their complex composition these products are hardly recycled and thermal treatment is preferred. In this study we investigated the thermal stability and material balance of nanostructured metal oxides in flames and in an industrial waste incinerator. We studied the size distribution of nanostructured metal oxides (CeO 2 , TiO 2 , SiO 2 ) in a flame reactor and in a heated reaction tube. In the premixed ethylene/air flame, nano-structured CeO 2 partly evaporates forming a new particle mode. This is probably due to chemical reactions in the flame. In addition sintering of agglomerates takes place in the flame. In the electrically heated reaction tube however only sintering of the agglomerated nanomaterials is observed. Ceria has a low background in waste incinerators and is therefore a suitable tracer for investigating the fate of nanostructured materials. Low concentrations of Ceria were introduced by a two-phase nozzle into the post-combustion zone of a waste incinerator. By the incineration of coal dust in a burning chamber the Ceria nanoparticles are mainly found in the size range of the fly ash (1 – 10 µm) because of agglomeration. With gas as a fuel less agglomeration was observed and the Ceria nanoparticles were in the particle size range below 1 µm. (paper)

  4. Thermal stability of nafion membranes under mechanical stress

    Energy Technology Data Exchange (ETDEWEB)

    Quintilii, M.; Struis, R. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1997-06-01

    The feasibility of adequately modified fluoro-ionomer membranes (NAFION{sup R}) is demonstrated for the selective separation of methanol synthesis products from the raw reactor gas at temperatures around 200{sup o}C. For an economically relevant application of this concept on a technical scale the Nafion membranes should be thin ({approx_equal}10 {mu}m) and thermally stable over a long period of time (1-2 years). In cooperation with industry (Methanol Casale SA, Lugano (CH)), we test the thermal stability of Nafion hollow fibers and supported Nafion thin sheet membranes at temperatures between 160 and 200{sup o}C under mechanical stress by applying a gas pressure difference over the membrane surface ({Delta}P{<=} 40 bar). Tests with the hollow fibers revealed that Nafion has visco-elastic properties. Tests with 50 {mu}m thin Nafion sheets supported by a porous metal carrier at 200{sup o}C and {Delta}P=39 bar showed no mechanical defects over a period of 92 days. (author) 5 figs., 4 refs.

  5. PLASMA THERMAL BARRIER COATINGS BASED ON ZIRCONIUM DIOXIDE WITH HIGH THERMAL STABILITY

    Directory of Open Access Journals (Sweden)

    O. G. Devoino

    2015-01-01

    Full Text Available The paper presents optimization of  processes for obtaining maximum content of tetragonal phase in the initial material and thermal barrier coatings (TBC based on zirconium dioxide and hafnium oxide.  Results of the investigations on phase composition of oxide HfO2 – ZrO2 – Y2O3  system have been given in the paper. The system represents  a microstructure which is similar to  zirconia dioxide and  transformed for its application at 1300 °C. The paper explains a mechanism of hafnium oxide influence on formation of the given microstructure. The research methodology has been based on complex metallography, X – ray diffraction and electron microscopic investigations of  structural elements of the composite plasma coating HfO2 – ZrO2 – Y2O system.In order to stabilize zirconium dioxide  dopant oxide should not only have an appropriate size of  metal ion, but also form a solid solution with the zirconia. This condition severely limits the number of possible stabilizers. In fact, such stabilization is possible only with the help of rare earth oxides (Y2O3, Yb2O3, CeO2, HfO2. Chemical purity of the applied materials plays a significant role for obtaining high-quality thermal barrier coatings. Hafnium oxide has been selected as powder for thermal barrier coatings instead of zirconium dioxide due to their similarities in structural modification, grating, chemical and physical properties and its high temperature structural transformations. It has been established that plasma thermal barrier HfO2 – ZrO2 – Y2O3 coatings consist of  one tetragonal phase. This phase is equivalent to a non-equilibrium tetragonal t' phase in the “zirconium dioxide stabilized with yttrium oxide” system. Affinity of  Hf+4 and Zr+4 cations leads to the formation of identical metastable phases during rapid quenching.

  6. Engineering a highly active thermophilic β-glucosidase to enhance its pH stability and saccharification performance.

    Science.gov (United States)

    Xia, Wei; Xu, Xinxin; Qian, Lichun; Shi, Pengjun; Bai, Yingguo; Luo, Huiying; Ma, Rui; Yao, Bin

    2016-01-01

    β-Glucosidase is an important member of the biomass-degrading enzyme system, and plays vital roles in enzymatic saccharification for biofuels production. Candidates with high activity and great stability over high temperature and varied pHs are always preferred in industrial practice. To achieve cost-effective biomass conversion, exploring natural enzymes, developing high level expression systems and engineering superior mutants are effective approaches commonly used. A newly identified β-glucosidase of GH3, Bgl3A, from Talaromyces leycettanus JCM12802, was overexpressed in yeast strain Pichia pastoris GS115, yielding a crude enzyme activity of 6000 U/ml in a 3 L fermentation tank. The purified enzyme exhibited outstanding enzymatic properties, including favorable temperature and pH optima (75 °C and pH 4.5), good thermostability (maintaining stable at 60 °C), and high catalytic performance (with a specific activity and catalytic efficiency of 905 U/mg and 9096/s/mM on pNPG, respectively). However, the narrow stability of Bgl3A at pH 4.0-5.0 would limit its industrial applications. Further site-directed mutagenesis indicated the role of excessive O-glycosylation in pH liability. By removing the potential O-glycosylation sites, two mutants showed improved pH stability over a broader pH range (3.0-10.0). Besides, with better stability under pH 5.0 and 50 °C compared with wild type Bgl3A, saccharification efficiency of mutant M1 was improved substantially cooperating with cellulase Celluclast 1.5L. And mutant M1 reached approximately equivalent saccharification performance to commercial β-glucosidase Novozyme 188 with identical β-glucosidase activity, suggesting its great prospect in biofuels production. In this study, we overexpressed a novel β-glucosidase Bgl3A with high specific activity and high catalytic efficiency in P. pastoris. We further proved the negative effect of excessive O-glycosylation on the pH stability of Bgl3A, and enhanced the pH

  7. A neutral pH thermal hydrolysis method for quantification of structured RNAs

    Science.gov (United States)

    Wilson, Stephen C.; Cohen, Daniel T.; Wang, Xin C.; Hammond, Ming C.

    2014-01-01

    Riboswitch aptamers adopt diverse and complex tertiary structural folds that contain both single-stranded and double-stranded regions. We observe that this high degree of secondary structure leads to an appreciable hypochromicity that is not accounted for in the standard method to calculate extinction coefficients using nearest-neighbor effects, which results in a systematic underestimation of RNA concentrations. Here we present a practical method for quantifying riboswitch RNAs using thermal hydrolysis to generate the corresponding pool of mononucleotides, for which precise extinction coefficients have been measured. Thermal hydrolysis can be performed at neutral pH without reaction quenching, avoids the use of nucleases or expensive fluorescent dyes, and does not require generation of calibration curves. The accuracy of this method for determining RNA concentrations has been validated using quantitative 31P-NMR calibrated to an external standard. We expect that this simple procedure will be generally useful for the accurate quantification of any sequence-defined RNA sample, which is often a critical parameter for in vitro binding and kinetic assays. PMID:24860014

  8. Effects of pH dynamics on solidification/stabilization of municipal solid waste incineration fly ash.

    Science.gov (United States)

    Yakubu, Yahaya; Zhou, Jun; Ping, Duan; Shu, Zhu; Chen, Yun

    2018-02-01

    Fly ash (FA), a product of municipal solid waste incineration (MSWI), has been classified as a kind of hazardous waste due to its high content of heavy metals. FA may be reused in the construction industry or disposed of at landfill sites, and thus poses threats to both the environment and human health. This study sought to establish a scientific basis for accurate selection of suitable pH storage conditions for the FA. We evaluated the potential of MSWI FA sample from the Xinghuo waste incineration power plant, Wuhan, to solidify/stabilize the heavy metal (Cu, Pb, Zn, Cr, Cd, As and Mn) contents, when leached under different pH conditions. The concentration of a heavy metal in the leachate was assumed to inversely reflect the extent of its solidification/stabilization (S/S). The study findings showed that the raw FA contained higher levels of the heavy metals, which were above the acceptable limits. Extremely acidic conditions favoured heavy metal leaching compared to extremely alkaline conditions. The extent of S/S of heavy metals was generally very low under highly acidic conditions (pH ≤ 4), but increased with increasing pH. All the metals solidified/stabilized in pH media of 5-11, except Zn which was detected in the entire pH range. We conclude that changing landfill conditions which can affect the pH environment, will increase heavy metal leaching when the pH ≤ 4. As a result, waste which was initially classified as non-hazardous may later pose harmful risks to both humans and the environment alike. We propose pH of 5-11 as the optimum pH range for the treatment, reuse, and disposal of the ash sample. Copyright © 2017 Elsevier Ltd. All rights reserved.

  9. Pipeline corrosion prevention by pH stabilization or corrosion inhibitors

    Energy Technology Data Exchange (ETDEWEB)

    Nyborg, Rolf [Institute for Energy Technology, Oslo (Norway)

    2009-07-01

    In many offshore oil and gas projects the pipeline costs are a considerable part of the investment and can become prohibitively high if the corrosivity of the fluid necessitates the use of corrosion resistant alloys instead of carbon steel. Development of more robust and reliable methods for internal corrosion control can increase the application range of carbon steel and therefore have a large economic impact. Corrosion control of carbon steel pipelines has traditionally often been managed by the use of corrosion inhibitors. The pH stabilization technique has been successfully used for corrosion control of several large wet gas pipelines in the last years. This method has advantages over film forming corrosion inhibitors when no or little formation water is produced. The use of corrosion inhibitors in multiphase pipelines implies several challenges which are not fully accounted for in traditional corrosion inhibitor testing procedures. Specialized test procedures have been developed to take account for the presence of emulsions dispersions and sand and clay particles in corrosion inhibitor testing. (author)

  10. Lutein-enriched emulsion-based delivery systems: Influence of pH and temperature on physical and chemical stability.

    Science.gov (United States)

    Davidov-Pardo, Gabriel; Gumus, Cansu Ekin; McClements, David Julian

    2016-04-01

    Lutein may be utilized in foods as a natural pigment or nutraceutical ingredient to improve eye health. Nevertheless, its use is limited by its poor water-solubility and chemical instability. We evaluated the effect of storage temperature and pH on the physical and chemical stability of lutein-enriched emulsions prepared using caseinate. The emulsions (initial droplet diameter=232 nm) remained physically stable at all incubation temperatures (5-70 °C); however the chemical degradation of lutein increased with increasing temperature (activation energy=38 kJ/mol). Solution pH had a major impact on the physical stability of the emulsions, causing droplet aggregation at pH 4 and 5. Conversely, the chemical stability of lutein was largely independent of the pH, with only a slight decrease in degradation at pH 8. This work provides important information for the rational design of emulsion-based delivery systems for a lipophilic natural dye and nutraceutical. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Effect of carbon nanospheres on shape stabilization and thermal behavior of phase change materials for thermal energy storage

    International Nuclear Information System (INIS)

    Mehrali, Mohammad; Tahan Latibari, Sara; Mehrali, Mehdi; Mahlia, Teuku Meurah Indra; Cornelis Metselaar, Hendrik Simon

    2014-01-01

    Highlights: • Introducing novel form-stable PCM of stearic acid (SA)/carbon nanospheres (CNSs). • The highest stabilized SA content is 83 wt% in the SA/CNS composites. • Increasing thermal conductivity of composite phase change material with high amount of latent heat. - Abstract: Stearic acid (SA) is one of the main phase change materials (PCMs) for medium temperature thermal energy storage systems. In order to stabilize the shape and enhance the thermal conductivity of SA, the effects of adding carbon nanospheres (CNSs) as a carbon nanofiller were examined experimentally. The maximum mass fraction of SA retained in CNSs was found as 80 wt% without the leakage of SA in a melted state, even when it was heated over the melting point of SA. The dropping point test shows that there was clearly no liquid leakage through the phase change process at the operating temperature range of the composite PCMs. The thermal stability and thermal properties of composite PCMs were investigated with a thermogravimetric analyzer (TGA) and differential scanning calorimeter (DSC), respectively. The thermal conductivity of the SA/CNS composite was determined by the laser flash method. The thermal conductivity at 35 °C increased about 105% for the highest loading of CNS (50 wt%). The thermal cycling test proved that form-stable composite PCMs had good thermal reliability and chemical durability after 1000 cycles of melting and freezing, which is advantageous for latent heat thermal energy storage (LHTES)

  12. Zirconia coating for enhanced thermal stability of gold nanoparticles

    Science.gov (United States)

    Pastre, A.; Cristini-Robbe, O.; Bois, L.; Chassagneux, F.; Branzea, D.; Boé, A.; Kinowski, C.; Raulin, K.; Rolland, N.; Bernard, R.

    2016-01-01

    This paper describes a rapid, simple and one-step method for the preparation of 2-4 nm diameter zirconia-coated gold nanoparticles at room temperature. These nanoparticles were synthesized by two simultaneous processes: the chemical reduction of tetrachloroauric acid with sodium borohydride and the formation of zirconia sol-gel matrices. All the gold nanoparticle sols were characterized by UV-visible absorption and transmission electron microscopy to determine the nanoparticle size and shape. The synthesis method is a combination of a polymeric structure of the amorphous zirconia and the use of a strong reducing agent, and it yields to very small quasi-spherical gold nanoparticles at room temperature. The thermal stability up to 1200 °C of the coated nanoparticles was studied by x-ray diffraction. The metastable tetragonal phase of the zirconia coating was obtained at 400 °C, and a progressive transformation from tetragonal to monoclinic phases of the zirconia coating was observed up to 1100 °C. After the heat treatment at 400 °C, the crystallite size of the gold nanoparticles was about 29 nm, and it remained unchanged from 400 °C to 1200 °C. These results are promising for the development of such materials as doping elements for optical fiber applications.

  13. Thermal stability of simple tetragonal and hexagonal diamond germanium

    Science.gov (United States)

    Huston, L. Q.; Johnson, B. C.; Haberl, B.; Wong, S.; Williams, J. S.; Bradby, J. E.

    2017-11-01

    Exotic phases of germanium, that form under high pressure but persist under ambient conditions, are of technological interest due to their unique optical and electrical properties. The thermal evolution and stability of two of these exotic Ge phases, the simple tetragonal (st12) and hexagonal diamond (hd) phases, are investigated in detail. These metastable phases, formed by high pressure decompression in either a diamond anvil cell or by nanoindentation, are annealed at temperatures ranging from 280 to 320 °C for st12-Ge and 200 to 550 °C for hd-Ge. In both cases, the exotic phases originated from entirely pure Ge precursor materials. Raman microspectroscopy is used to monitor the phase changes ex situ following annealing. Our results show that hd-Ge synthesized via a pure form of a-Ge first undergoes a subtle change in structure and then an irreversible phase transformation to dc-Ge with an activation energy of (4.3 ± 0.2) eV at higher temperatures. St12-Ge was found to transform to dc-Ge with an activation energy of (1.44 ± 0.08) eV. Taken together with results from previous studies, this study allows for intriguing comparisons with silicon and suggests promising technological applications.

  14. Silver nanoparticles modified by gelatin with extraordinary pH stability and long-term antibacterial activity.

    Science.gov (United States)

    Sivera, Martin; Kvitek, Libor; Soukupova, Jana; Panacek, Ales; Prucek, Robert; Vecerova, Renata; Zboril, Radek

    2014-01-01

    The potential for application of any nanoparticles, including silver nanoparticles (AgNPs), is strongly dependent on their stability against aggregation. Therefore, improvement of this parameter is a key task, especially in the case of AgNPs, because a correlation between size and biological activity has been demonstrated. In the present work, a natural stabilizer, gelatin, was investigated for the stabilization of AgNPs in an aqueous dispersion. The particles were prepared via a modified Tollens process, and the gelatin modifier was added prior to the reducing agent. The stability against aggregation of the AgNPs prepared by this method was more than one order of magnitude higher (on the basis of the critical coagulation concentration (CCC)) than that of AgNPs prepared via a similar method but without the assistance of gelatin. Their high stability against aggregation was confirmed over wide pH range (from 2 to 13) in which the particles did not exhibit rapid aggregation; such stability has not been previously reported for AgNPs. Additionally, gelatin not only fulfills the role of a unique stabilizer but also positively influences the modified Tollens process used to prepare the AgNPs. The diameter of the gelatin-modified AgNPs was substantially smaller in comparison to those prepared without gelatin. The polydispersity of the dispersion significantly narrowed. Moreover, the gelatin-stabilized AgNPs exhibited long-term stability against aggregation and maintained high antibacterial activity when stored for several months under ambient conditions.

  15. Silicon-photonic PTAT temperature sensor for micro-ring resonator thermal stabilization.

    Science.gov (United States)

    Saeedi, Saman; Emami, Azita

    2015-08-24

    We present a scheme for thermal stabilization of micro-ring resonator modulators through direct measurement of ring temperature using a monolithic PTAT temperature sensor. The measured temperature is used in a feedback loop to adjust the thermal tuner of the ring. The closed-loop feedback system is demonstrated to operate in presence of thermal perturbations at 20Gb/s.

  16. Thermal and Chemical Stabilization of Silver Nanoplates for Plasmonic Sensor Application.

    Science.gov (United States)

    Takahashi, Yukina; Suga, Koichi; Ishida, Takuya; Yamada, Sunao

    2016-01-01

    Thermal and chemical stabilities of silver nanoplates (AgPLs), which are triangle plate-shaped silver nanoparticles, were improved by coating with titanium oxide. The titanium oxide layer prepared by a dip-coating method was certainly advantageous for the improvement of thermal stability. Furthermore, the overlayering of titanium oxide by a spray pyrolysis method was quite useful for improving the chemical stability against I(-) exposure. Such a coating exhibited satisfactory refractive index sensitivities.

  17. The effect of wood extractives on the thermal stability of different wood species

    Energy Technology Data Exchange (ETDEWEB)

    Shebani, A.N.; Reenen, A.J. van [Department of Chemistry and Polymer Science, University of Stellenbosch, Private Bag X1, Matieland 7602 (South Africa); Meincken, M. [Department of Forest and Wood Science, University of Stellenbosch, Private Bag X1, Matieland 7602 (South Africa)], E-mail: mmein@sun.ac.za

    2008-05-30

    This study compares the thermal stability of different wood species, which is an important factor for the production of wood-polymer composites (WPCs), and investigates the effect of extraction on thermal properties. The chemical composition of four wood species -Quercus alba, Pinus radiata, Eucalyptus grandis and Acacia cyclops - has been determined, as the species is expected to affect the thermal stability of wood. Subsequently, the hot-water (HW) extractives, ethanol/cyclohexane (E/C) extractives and both extractives were eliminated from the wood via Soxhlet extraction and the thermal stability of the wood determined with thermogravimetric analysis (TGA) under identical conditions. The results suggest that a higher cellulose and lignin content leads to better thermal stability of wood in different temperature regimes. In all cases, the removal of extractives improved the thermal stability of the wood. The effect of combined extractions was more pronounced than of an individual extraction and E/C-extraction caused less improvement in the thermal stability of wood than HW extraction. The degradation of the investigated wood extractives occurred at low rates over a broad temperature range. Pure cellulose exhibited superior thermal stability compared to wood, but differences were observed between the investigated wood species.

  18. First-principles calculation of thermodynamic stability of acids and bases under pH environment: A microscopic pH theory

    Science.gov (United States)

    Kim, Yong-Hyun; Kim, Kwiseon; Zhang, S. B.

    2012-04-01

    Despite being one of the most important thermodynamic variables, pH has yet to be incorporated into first-principles thermodynamics to calculate stability of acidic and basic solutes in aqueous solutions. By treating the solutes as defects in homogeneous liquids, we formulate a first-principles approach to calculate their formation energies under proton chemical potential, or pH, based on explicit molecular dynamics. The method draws analogy to first-principle calculations of defect formation energies under electron chemical potential, or Fermi energy, in semiconductors. From this, we propose a simple pictorial representation of the general theory of acid-base chemistry. By performing first-principles molecular dynamics of liquid water models with solutes, we apply the formulation to calculate formation energies of various neutral and charged solutes such as H+, OH-, NH3, NH4+, HCOOH, and HCOO- in water. The deduced auto-dissociation constant of water and the difference in the pKa values of NH3 and HCOOH show good agreement with known experimental values. Our first-principles approach can be further extended and applied to other bio- and electro-chemical molecules such as amino acids and redox reaction couples that could exist in aqueous environments to understand their thermodynamic stability.

  19. STABILITY OF BETACYANIN PIGMENTS FROM RED PURPLE PITAYA FRUIT (Hylocereus polyrhizus : INFLUENCE OF PH, TEMPERATURE, METAL IONS AND ASCORBIC ACID

    Directory of Open Access Journals (Sweden)

    Tang, C.S Tang, C.S

    2010-06-01

    Full Text Available Betacyanin pigments from red-purple pitaya fruit (Hylocereus polyrhizus could be an attractive source of red colourant for food application. This paper presents results on the extraction of betacyanin pigments from pitaya fruits grown locally in Malaysia. Both the flesh of the fruit and its mesocarp were investigated and it was found that the flesh had higher pigment contents compared to its peel component. The concentration of betacyanins expressed as betanin equivalents per 100 g of flesh and peel were 10.1 ± 0.6 mg and 6.7 ± 0.2 mg, respectively when 80% methanol was used.  The stability of betacyanin pigments were investigated at different pH, temperature and in presence of different concentrations of metal ions (Cu2+ and Fe2+ and ascorbic acid. The results showed that the pigment was most stable at pH range between 5 and 6. However, it forfeited its stability to the heat induced at elevated temperatures. Metal ions (Cu2+ and Fe2+ proved to be capable of accelerating betacyanin degradation, with Cu2+ exhibiting the greatest effect. By contrast, supplementation with ascorbic acid could enhance the pigment stability against the detrimental effects caused by pH, temperature and metal ions. Nevertheless, if the concentration of ascorbic acid exceeds 0.7 %, it may change its role from pigment stabilizer to become a pro-oxidant.    Keywords: Betacyanin, pigments, pitaya fruit, Hylocereus polyrhizus, ascorbic acid

  20. Enhanced gastric stability of esomeprazole by molecular interaction and modulation of microenvironmental pH with alkalizers in solid dispersion.

    Science.gov (United States)

    Van Nguyen, Hien; Baek, Namhyun; Lee, Beom-Jin

    2017-05-15

    Due to the instability of esomeprazole magnesium dihydrate (EPM), a proton pump inhibitor, in gastric fluid, enteric-coated dosage form is commonly used for therapeutic application. In this study, we prepared new gastric fluid resistant solid dispersions (SDs) containing alkalizers. Then, new mechanistic evidence regarding the effects of pharmaceutical alkalizers on the aqueous stability of EPM in simulated gastric fluid was investigated. The alkalizer-loaded SD were prepared by dissolving or dispersing EPM, hydroxypropyl methylcellulose (HPMC) 6 cps, and an alkalizer, in ethanol 50% (v/v) followed by spray drying. Nine different alkalizers were assessed for in vitro stability in two media, simulated gastric fluid (pH 1.2 buffer) and simulated intestinal fluid (pH 6.8 buffer). The microenvironmental pH (pH M ) was measured to evaluate the effect of the alkalizer on the pH M of SDs. Drug crystallinity and morphology of the SDs were also examined by differential scanning calorimetry (DSC), powder X-ray diffraction (PXRD), and scanning electron microscopy (SEM). The interactions among EPM, the polymer, and the alkalizer were elucidated by Fourier transform infrared (FTIR) spectroscopy. The in vivo absorption studies of the optimized alkalizer-containing SD and the enteric-coated reference tablet Nexium ® were then conducted in beagle dogs. Among alkalizers, MgO loaded in SDs proved to be the best alkalizer to stabilize EPM in simulated gastric fluid. pH M values of the alkalizer-containing SDs were significantly higher than that of the SD without alkalizer. The pH M values decreased in the following order: MgO, Na 2 CO 3 , Ca(OH) 2 , and no alkalizer. DSC and PXRD data exhibited a change in the drug crystallinity of the SDs from crystalline to amorphous form. SEM data showed a relatively spherical shape of the MgO-loaded SD compared to the less-defined shape of pure drug. FTIR indicated a strong molecular interaction among EPM, alkalizer and polymer; in particular

  1. Effect of acid rain pH on leaching behavior of cement stabilized lead-contaminated soil.

    Science.gov (United States)

    Du, Yan-Jun; Wei, Ming-Li; Reddy, Krishna R; Liu, Zhao-Peng; Jin, Fei

    2014-04-30

    Cement stabilization is a practical approach to remediate soils contaminated with high levels of lead. However, the potential for leaching of lead out of these stabilized soils under variable acid rain pH conditions is a major environmental concern. This study investigates the effects of acid rain on the leaching characteristics of cement stabilized lead contaminated soil under different pH conditions. Clean kaolin clay and the same soil spiked with 2% lead contamination are stabilized with cement contents of 12 and 18% and then cured for 28 days. The soil samples are then subjected to a series of accelerated leaching tests (or semi-dynamic leaching tests) using a simulated acid rain leachant prepared at pH 2.0, 4.0 or 7.0. The results show that the strongly acidic leachant (pH ∼2.0) significantly altered the leaching behavior of lead as well as calcium present in the soil. However, the differences in the leaching behavior of the soil when the leachant was mildly acidic (pH ∼4.0) and neutral (pH ∼7.0) prove to be minor. In addition, it is observed that the lead contamination and cement content levels can have a considerable impact on the leaching behavior of the soils. Overall, the leachability of lead and calcium is attributed to the stability of the hydration products and their consequent influence on the soil buffering capacity and structure. Copyright © 2014 Elsevier B.V. All rights reserved.

  2. Stability of Anthocyanins and Their Degradation Products from Cabernet Sauvignon Red Wine under Gastrointestinal pH and Temperature Conditions.

    Science.gov (United States)

    Yang, Ping; Yuan, Chunlong; Wang, Hua; Han, Fuliang; Liu, Yangjie; Wang, Lin; Liu, Yang

    2018-02-07

    This study investigated the stability of wine anthocyanins under simulated gastrointestinal pH and temperature conditions, and further studied the evolution of anthocyanin degradation products through simulated digestive conditions. The aim of this study was to investigate the relation between anthocyanins' structure and their digestive stability. Results showed that a total of 22 anthocyanins were identified in wine and most of these anthocyanins remained stable under simulated gastric digestion process. However, a dramatic concentration decrease happened to these anthocyanins during simulated intestinal digestion. The stability of anthocyanins in digestive process appeared to be related to their structure. The methoxy group in the B-ring enhanced the stability of anthocyanins, whereas hydroxyl group resulted in a reduction of their stability. Acylation decreased the stability of malvidin 3- O -glucoside. Pyruvic acid conjugation enhanced the structural stability of pyranoanthocyanins, whereas acetaldehyde attachment weakened their stability. A commercial malvidin 3- O -glucoside standard was used to investigate anthocyanin degradation products under simulated digestion process, and syringic acid, protocatechuic acid and vanillic acid were confirmed to be the degradation products via anthocyanin chalcone conversion path. Gallic acid, protocatechuic acid, vanillic acid, syringic acid, and p -coumaric acid in wine experienced a significant concentration decrease during digestion process. However, wine model solution revealed that phenolic acids remained stable under gastrointestinal conditions, except gallic acid.

  3. Stability of Anthocyanins and Their Degradation Products from Cabernet Sauvignon Red Wine under Gastrointestinal pH and Temperature Conditions

    Directory of Open Access Journals (Sweden)

    Ping Yang

    2018-02-01

    Full Text Available This study investigated the stability of wine anthocyanins under simulated gastrointestinal pH and temperature conditions, and further studied the evolution of anthocyanin degradation products through simulated digestive conditions. The aim of this study was to investigate the relation between anthocyanins’ structure and their digestive stability. Results showed that a total of 22 anthocyanins were identified in wine and most of these anthocyanins remained stable under simulated gastric digestion process. However, a dramatic concentration decrease happened to these anthocyanins during simulated intestinal digestion. The stability of anthocyanins in digestive process appeared to be related to their structure. The methoxy group in the B-ring enhanced the stability of anthocyanins, whereas hydroxyl group resulted in a reduction of their stability. Acylation decreased the stability of malvidin 3-O-glucoside. Pyruvic acid conjugation enhanced the structural stability of pyranoanthocyanins, whereas acetaldehyde attachment weakened their stability. A commercial malvidin 3-O-glucoside standard was used to investigate anthocyanin degradation products under simulated digestion process, and syringic acid, protocatechuic acid and vanillic acid were confirmed to be the degradation products via anthocyanin chalcone conversion path. Gallic acid, protocatechuic acid, vanillic acid, syringic acid, and p-coumaric acid in wine experienced a significant concentration decrease during digestion process. However, wine model solution revealed that phenolic acids remained stable under gastrointestinal conditions, except gallic acid.

  4. Thermal phase stability of some simulated Defense waste glasses

    International Nuclear Information System (INIS)

    May, R.P.

    1981-04-01

    Three simulated defense waste glass compositions developed by Savannah River Laboratories were studied to determine viscosity and compositional effects on the comparative thermal phase stabilities of these glasses. The glass compositions are similar except that the 411 glasses are high in lithium and low in sodium compared to the 211 glass, and the T glasses are high in iron and low in aluminum compared to the C glass. Specimens of these glasses were heat treated using isothermal anneals as short as 10 min and up to 15 days over the temperature range of 450 0 C to 1100 0 C. Additionally, a specimen of each glass was cooled at a constant cooling rate of 7 0 C/hour from an 1100 0 C melt down to 500 0 C where it was removed from the furnace. The following were observed. The slow cooling rate of 7 0 C/hour is possible as a canister centerline cooling rate for large canisters. Accordingly, it is important to note that a short range diffusion mechanism like cooperative growth phenomena can result in extensive devitrification at lower temperatures and higher yields than a long-range diffusion mechanism can; and can do it without the growth of large crystals that can fracture the glass. Refractory oxides like CeO 2 and (Ni, Mn, Fe) 2 O 4 form very rapidly at higher temperatures than silicates and significant yields can be obtained at sufficiently high temperatures that settling of these dense phases becomes a major microstructural feature during slow cooling of some glasses. These annealing studies further show that below 500 0 C there is but little devitrification occurring implying that glass canisters stored at 300 0 C may be kinetically stable despite not being thermodynamically so

  5. Thermal phase stability of some simulated Defense waste glasses

    Energy Technology Data Exchange (ETDEWEB)

    May, R.P.

    1981-04-01

    Three simulated defense waste glass compositions developed by Savannah River Laboratories were studied to determine viscosity and compositional effects on the comparative thermal phase stabilities of these glasses. The glass compositions are similar except that the 411 glasses are high in lithium and low in sodium compared to the 211 glass, and the T glasses are high in iron and low in aluminum compared to the C glass. Specimens of these glasses were heat treated using isothermal anneals as short as 10 min and up to 15 days over the temperature range of 450/sup 0/C to 1100/sup 0/C. Additionally, a specimen of each glass was cooled at a constant cooling rate of 7/sup 0/C/hour from an 1100/sup 0/C melt down to 500/sup 0/C where it was removed from the furnace. The following were observed. The slow cooling rate of 7/sup 0/C/hour is possible as a canister centerline cooling rate for large canisters. Accordingly, it is important to note that a short range diffusion mechanism like cooperative growth phenomena can result in extensive devitrification at lower temperatures and higher yields than a long-range diffusion mechanism can; and can do it without the growth of large crystals that can fracture the glass. Refractory oxides like CeO/sub 2/ and (Ni, Mn, Fe)/sub 2/O/sub 4/ form very rapidly at higher temperatures than silicates and significant yields can be obtained at sufficiently high temperatures that settling of these dense phases becomes a major microstructural feature during slow cooling of some glasses. These annealing studies further show that below 500/sup 0/C there is but little devitrification occurring implying that glass canisters stored at 300/sup 0/C may be kinetically stable despite not being thermodynamically so.

  6. Thermal stability, swelling behavior and CO 2 absorption properties of Nanoscale Ionic Materials (NIMs)

    KAUST Repository

    Andrew Lin, Kun-Yi

    2014-11-11

    © The Royal Society of Chemistry 2015. Nanoscale Ionic Materials (NIMs) consist of a nanoscale core, a corona of charged brushes tethered on the surface of the core, and a canopy of the oppositely charged species linked to the corona. Unlike conventional polymeric nanocomposites, NIMs can display liquid-like behavior in the absence of solvents, have a negligible vapor pressure and exhibit unique solvation properties. These features enable NIMs to be a promising CO2 capture material. To optimize NIMs for CO2 capture, their structure-property relationships were examined by investigating the roles of the canopy and the core in their thermal stability, and thermally- and CO2-induced swelling behaviors. NIMs with different canopy sizes and core fractions were synthesized and their thermal stability as well as thermally- and CO2-induced swelling behaviors were determined using thermogravimetry, and ATR FT-IR and Raman spectroscopies. It was found that the ionic bonds between the canopy and the corona, as well as covalent bonds between the corona and the core significantly improved the thermal stability compared to pure polymer and polymer/nanofiller mixtures. A smaller canopy size and a larger core fraction led to a greater enhancement in thermal stability. This thermal stability enhancement was responsible for the long-term thermal stability of NIMs over 100 temperature swing cycles. Owing to their ordered structure, NIMs swelled less when heated or when they adsorbed CO2 compared to their corresponding polymers. This journal is

  7. Influence of thermal effects on stability of nanoscale films and filaments on thermally conductive substrates

    Science.gov (United States)

    Seric, Ivana; Afkhami, Shahriar; Kondic, Lou

    2018-01-01

    We consider fluid films and filaments of nanoscale thickness on thermally conductive substrates exposed to external heating and discuss the influence of the variation of material parameters with temperature on film stability. Particular focus is on metal films exposed to laser irradiation. Due to the short length scales involved, the absorption of heat in the metal is directly coupled to the film evolution, since the absorption length and the film thickness are comparable. Such a setup requires self-consistent consideration of fluid mechanical and thermal effects. We approach the problem via volume-of-fluid-based simulations that include destabilizing liquid metal-solid substrate interaction potentials. These simulations couple fluid dynamics directly with the spatio-temporal evolution of the temperature field both in the fluid and in the substrate. We focus on the influence of the temperature variation of material parameters, in particular of surface tension and viscosity. Regarding variation of surface tension with temperature, the main finding is that while the Marangoni effect may not play a significant role in the considered setting, the temporal variation of surface tension (modifying normal stress balance) is significant and could lead to complex evolution including oscillatory evolution of the liquid metal-air interface. Temperature variation of film viscosity is also found to be relevant. Therefore, the variations of surface tensions and viscosity could both influence the emerging wavelengths in experiments. By contrast, the filament geometry is found to be much less sensitive to a variation of material parameters with temperature.

  8. pH- and thermal-dependent conformational transition of PGAIPG, a repeated hexapeptide sequence from tropoelastin.

    Science.gov (United States)

    Lin, Shan-Yang; Hsieh, Tzu-Feng; Wei, Yen-Shan

    2005-04-01

    The secondary structure of PGAIPG (Pro-Gly-Ala-IIe-Pro-Gly), a repeated hexapeptide of tropoelastin, in buffer solution of different pH was determined by using attenuated total reflection-Fourier transform infrared (ATR-FTIR) spectroscopy. The thermal-dependent structural change of PGAIPG in aqueous solution or in solid state was also examined by thermal FTIR microspectroscopy. The conformation of PGAIPG in aqueous solution exhibited a pH-dependent structural characterization. A predominant peak at 1614 cm(-1) (aggregated beta-sheet) with a shoulder near 1560 cm(-1) (beta-sheet) appeared in pH 5.5-8.5 buffer solutions. A new broad shoulder at 1651 cm(-1) (random coil and/or alpha-helix) with 1614 cm(-1) was observed in the pH 4.5 buffer solution. However, the broad shoulder at 1651 cm(-1) was converted to a maximum peak at 1679 cm(-1) (beta-turn/antiparallel beta-sheet) when the pH shifted from 4.5 to 3.5, but the original pronounced peak at 1614 cm(-1) became a shoulder. Once the pH was lowered to 2.5, the IR spectrum of PGAIPG was dominated by major absorption at 1679 cm(-1) with a minor peak at 1552 cm(-1) (alpha-helix/random coil). The result indicates that the pH was a predominant factor to transform PGAIPG structure from aggregated beta-sheet (pH 8.5) to beta-turn/intermolecular antiparallel beta-sheet (pH 2.5). Moreover, a partial conformation of PGAIPG with minor alpha-helix/random coil structures was also explored in the lower pH buffer solution. There was no thermal-dependent structural change for solid-state PGAIPG. The thermal-induced formation of aggregated beta-sheet for PGAIPG in aqueous solution was found from 28 to 30 degrees C, however, which might be correlated with the formation of an opaque gel that turned from clear solution. The formation of aggregated beta-sheet structure for PGAIPG beyond 30 degrees C might be due to the intermolecular hydrogen bonded interaction between the hydrophobic PGAIPG fragments induced by coacervation.

  9. Transmembrane helix-helix association: relative stabilities at low pH.

    Science.gov (United States)

    Valluru, Neelima; Silva, Frances; Dhage, Manmath; Rodriguez, Gustavo; Alloor, Srinivas R; Renthal, Robert

    2006-04-11

    We have previously studied the unfolding equilibrium of bacterioopsin in a single phase solvent, using Förster mechanism fluorescence resonance energy transfer (FRET) as a probe, from tryptophan donors to a dansyl acceptor. We observed an apparent unfolding transition in bacterioopsin perturbed by increasing ethanol concentrations [Nannepaga et al. (2004) Biochemistry 43, 50-59]. We have further investigated this transition and find that the unfolding is pH-dependent. We have now measured the apparent pK of acid-induced unfolding of bacterioopsin in 90% ethanol. When the acceptor is on helix B (Lys 41), the apparent pK for unfolding is 4.75; on the EF connecting loop (Cys 163), 5.15; and on helix G (Cys 222), 5.75. Five-helix proteolytic fragments are less stable. The apparent unfolding pKs are 5.46 for residues 72-248 (Cys 163) and 7.36 for residues 1-166 (Lys 41). When interpreted in terms of a simple equilibrium model for unfolding, the apparent pKs give relative free energies of unfolding in the range of -0.54 to -3.5 kcal/mol. The results suggest that the C-terminal helix of bacterioopsin is less stably folded than the N-terminal helices. We analyzed the pairwise helix-helix interaction surfaces of bacteriorhodopsin and three other seven-transmembrane-helix proteins on the basis of crystal structures. The results show that the interaction surfaces are smoother and the helix axis separations are closer in the amino-terminal two-thirds of the proteins compared with the carboxyl-terminal one-third. However, the F helix is important in stabilizing the folded structure, as shown by the instability of the 1-166 fragment. Considering the high-resolution crystal structure of bacteriorhodopsin, there are no obvious helix-helix interactions involving protein side chains which would be destabilized by protonation at the estimated pH of the unfolding transitions. However, a number of helix-bridging water molecules could become protonated, thereby weakening the helix

  10. Stabilization of Metal-Loaded Ion-Exchange Resin with a Porous Silica Supporter Through Thermal Treatment

    Energy Technology Data Exchange (ETDEWEB)

    Kim, I-T. Park, H-S.; Yoo, J-H.; Kim, J-H.

    2003-02-25

    A new ion exchanger with porous silica as a supporting material and diphosphonic acid as a functional chelating group has been developed at ANL for the effective removal of transition metals and actinide ions from very acidic radioactive liquid wastes. The applicability of this resin for the treatment of low- and/or intermediate-level aqueous waste from nuclear power plants (NPP) has not been reported in scientific literature, but is under study now in Korea. The major radioisotopes in NPP radioactive liquid waste are Cs and Co in neutral pH ranges. This study on the thermal stabilization of metal-loaded waste resin has been carried out in parallel with the sorption experiment. Thermal treatment of metal (Co, Cs or U) loaded resin was accomplished to see the possibility of enhancing the safety and stability of the final product during transportation and disposal. In this paper, characteristics of the metal-loaded resins before and after heat treatment at three different thermal conditions were investigated and compared with each other to see the effectiveness of the thermal treatment method.

  11. The role of pH and Mg on the stability and crystallization of amorphous calcium carbonate

    International Nuclear Information System (INIS)

    Rodriguez-Blanco, J.D.; Shaw, S.; Bots, P.; Roncal-Herrero, T.; Benning, L.G.

    2012-01-01

    Highlights: ► We studied the effect of pH and Mg in the crystallization of amorphous CaCO 3 (ACC). ► The study combined synchrotron-based scattering with electron microscopy. ► The pH-dependent C speciation and hydration strength of Mg 2+ control ACC structure. ► This ACC structure governs the ACC dissolution rate and crystallization pathway. - Abstract: The effects of pH and Mg on the crystallization of amorphous calcium carbonate (ACC) to vaterite and/or calcite were studied using a combination of in situ time resolved synchrotron-based techniques and electron microscopy. The experiments showed that Mg increased the stability of ACC and favoured the formation of calcite over vaterite. A neutral (∼7) starting pH during mixing promoted the transformation of ACC into calcite via a dissolution/reprecipitation mechanism. Conversely, when ACC formed in a solution that started with a high initial pH (∼11.5), the transformation to calcite occurred via metastable vaterite, which formed via a spherulitic growth mechanism. In a second stage this vaterite transformed to calcite via a surface-controlled dissolution and recrystallization mechanism. These crystallization pathways can be explained as a consequence of the pH-dependent composition, local structure, stability and dissolution rates of ACC.

  12. Comprehensive stabilization mechanism of electron-beam irradiated polyacrylonitrile fibers to shorten the conventional thermal treatment

    Science.gov (United States)

    Park, Sejoon; Yoo, Seung Hwa; Kang, Ha Ri; Jo, Seong Mu; Joh, Han-Ik; Lee, Sungho

    2016-01-01

    An electron beam was irradiated on polyacrylonitrile (PAN) fibers prior to thermal stabilization. The electron-beam irradiation effectively shortened the thermal stabilization process by one fourth compared with the conventional thermal stabilization process. A comprehensive mechanistic study was conducted regarding this shortening of the thermal stabilization by electron-beam irradiation. Various species of chain radicals were produced in PAN fibers by electron-beam irradiation and existed for a relatively long duration, as observed by electron spin resonance spectroscopy. Subsequently, these radicals were gradually oxidized to peroxy radicals in the presence of oxygen under storage or heating. We found that these peroxy radicals (CO) enabled such an effective shortcut of thermal stabilization by acting as intermolecular cross-linking and partial aromatization points in the low temperature range (100–130 °C) and as earlier initiation seeds of successive cyclization reactions in the next temperature range (>130–140 °C) of thermal stabilization. Finally, even at a low irradiation dose (200 kGy), followed by a short heat treatment (230 °C for 30 min), the PAN fibers were sufficiently stabilized to produce carbon fibers with tensile strength and modulus of 2.3 and 216 GPa, respectively, after carbonization. PMID:27349719

  13. Comprehensive stabilization mechanism of electron-beam irradiated polyacrylonitrile fibers to shorten the conventional thermal treatment

    Science.gov (United States)

    Park, Sejoon; Yoo, Seung Hwa; Kang, Ha Ri; Jo, Seong Mu; Joh, Han-Ik; Lee, Sungho

    2016-06-01

    An electron beam was irradiated on polyacrylonitrile (PAN) fibers prior to thermal stabilization. The electron-beam irradiation effectively shortened the thermal stabilization process by one fourth compared with the conventional thermal stabilization process. A comprehensive mechanistic study was conducted regarding this shortening of the thermal stabilization by electron-beam irradiation. Various species of chain radicals were produced in PAN fibers by electron-beam irradiation and existed for a relatively long duration, as observed by electron spin resonance spectroscopy. Subsequently, these radicals were gradually oxidized to peroxy radicals in the presence of oxygen under storage or heating. We found that these peroxy radicals (CO) enabled such an effective shortcut of thermal stabilization by acting as intermolecular cross-linking and partial aromatization points in the low temperature range (100-130 °C) and as earlier initiation seeds of successive cyclization reactions in the next temperature range (>130-140 °C) of thermal stabilization. Finally, even at a low irradiation dose (200 kGy), followed by a short heat treatment (230 °C for 30 min), the PAN fibers were sufficiently stabilized to produce carbon fibers with tensile strength and modulus of 2.3 and 216 GPa, respectively, after carbonization.

  14. Screening of hydrocarbons as supercritical ORCs working fluids by thermal stability

    International Nuclear Information System (INIS)

    Dai, Xiaoye; Shi, Lin; An, Qingsong; Qian, Weizhong

    2016-01-01

    Highlights: • A rapid evaluation method for thermal stability of hydrocarbons for ORCs. • Methane and hydrogen are confirmed to be decomposition indicators. • The decomposition temperatures for some hydrocarbons using the rapid method. • Long carbon chain hydrocarbons are not suitable for supercritical ORCs. - Abstract: Organic Rankine Cycle (ORC) systems are widely used for industrial waste heat recovery and renewable energy utilization. The supercritical ORC is currently one of the main development directions due to its low exergy loss, high thermal efficiency and high work output. The thermal stability is the major limitation of organic working fluid selection with high temperature heat sources. This paper presents a rapid experimental method for assessing the thermal stability of hydrocarbons for ORCs. The fluids were tested in a high temperature reactor with methane and hydrogen theoretically and experimentally confirmed to be the indicators of thermal decomposition. The thermal decomposition temperatures were obtained for n-hexane, n-pentane, isopentane, cyclopentane, n-butane and isobutane using the rapid experimental method. The results show that cycloalkanes are not the good choices by thermal stability and long carbon chain hydrocarbons (longer than C6) are not suitable for supercritical ORCs due to the thermal stability limitation.

  15. Structure and Mechanical Properties of Al-Cu-Fe-X Alloys with Excellent Thermal Stability.

    Science.gov (United States)

    Školáková, Andrea; Novák, Pavel; Mejzlíková, Lucie; Průša, Filip; Salvetr, Pavel; Vojtěch, Dalibor

    2017-11-05

    In this work, the structure and mechanical properties of innovative Al-Cu-Fe based alloys were studied. We focused on preparation and characterization of rapidly solidified and hot extruded Al-Cu-Fe, Al-Cu-Fe-Ni and Al-Cu-Fe-Cr alloys. The content of transition metals affects mechanical properties and structure. For this reason, microstructure, phase composition, hardness and thermal stability have been investigated in this study. The results showed exceptional thermal stability of these alloys and very good values of mechanical properties. Alloying by chromium ensured the highest thermal stability, while nickel addition refined the structure of the consolidated alloy. High thermal stability of all tested alloys was described in context with the transformation of the quasicrystalline phases to other types of intermetallics.

  16. History of Sulphur Content Effects on the Thermal Stability of RP-1 under Heated Conditions

    National Research Council Canada - National Science Library

    Irvine, Solveig

    2004-01-01

    ... over the outdated Mil-Specification for the fuel. This current specification allows high valued limits on contaminants such as sulfur compounds, and also lacks specification of required thermal stability qualifications for the fuel...

  17. Silver nanoparticles modified by gelatin with extraordinary pH stability and long-term antibacterial activity.

    Directory of Open Access Journals (Sweden)

    Martin Sivera

    Full Text Available The potential for application of any nanoparticles, including silver nanoparticles (AgNPs, is strongly dependent on their stability against aggregation. Therefore, improvement of this parameter is a key task, especially in the case of AgNPs, because a correlation between size and biological activity has been demonstrated. In the present work, a natural stabilizer, gelatin, was investigated for the stabilization of AgNPs in an aqueous dispersion. The particles were prepared via a modified Tollens process, and the gelatin modifier was added prior to the reducing agent. The stability against aggregation of the AgNPs prepared by this method was more than one order of magnitude higher (on the basis of the critical coagulation concentration (CCC than that of AgNPs prepared via a similar method but without the assistance of gelatin. Their high stability against aggregation was confirmed over wide pH range (from 2 to 13 in which the particles did not exhibit rapid aggregation; such stability has not been previously reported for AgNPs. Additionally, gelatin not only fulfills the role of a unique stabilizer but also positively influences the modified Tollens process used to prepare the AgNPs. The diameter of the gelatin-modified AgNPs was substantially smaller in comparison to those prepared without gelatin. The polydispersity of the dispersion significantly narrowed. Moreover, the gelatin-stabilized AgNPs exhibited long-term stability against aggregation and maintained high antibacterial activity when stored for several months under ambient conditions.

  18. Immobilization of laccase on modified silica: stabilization, thermal inactivation and kinetic behaviour in 1-ethyl-3-methylimidazolium ethylsulfate ionic liquid.

    Science.gov (United States)

    Tavares, Ana P M; Rodríguez, Oscar; Fernández-Fernández, María; Domínguez, Alberto; Moldes, Diego; Sanromán, María A; Macedo, Eugénia A

    2013-03-01

    Laccase was immobilized on modified silica carrier. The immobilization conditions, pH and enzyme concentration were optimized. Operational stability of 10 reaction cycles showed that immobilized laccase in buffer was stable, presenting an activity loss 80% was obtained in ionic liquid (IL) solution. Activity of immobilized laccase was maintained when incubated in IL. After 7days of incubation, immobilized laccase lost 30-50% of its initial activity. Immobilization also improved thermal stability of laccase in the presence of IL. Enzyme kinetics was modelled with Michaelis-Menten model. The Km value for free laccase increases significantly with the IL concentration. Slight differences were found in Vm for free enzyme. Unusual kinetic behaviour was obtained for immobilized laccase in IL: Both Vm and Km increased with IL concentration, resulting in increased catalytic efficiency of the immobilized enzyme in presence of IL. Copyright © 2013. Published by Elsevier Ltd.

  19. The thermal stability of poly(methyl methacrylate prepared by RAFT polymerisation

    Directory of Open Access Journals (Sweden)

    LYNNE KATSIKAS

    2008-08-01

    Full Text Available Poly(methyl methacrylate, PMMA, was prepared by reversible addition–fragmentation chain transfer, RAFT, polymerisation using 2-(2-cyanopropyl-dithiobenzoate, CPDB, as the RAFT agent. The thermal stability of the resulting polymer approached that of anionically prepared PMMA, as determined by thermogravimetry. This was the consequence of the RAFT prepared polymer having no head-to-head links and no chain end double bonds, which are responsible for the relatively low thermal stability of radically prepared PMMA.

  20. Fluorescent pyrene-centered starburst oligocarbazoles with excellent thermal and electrochemical stabilities.

    Science.gov (United States)

    Ren, Ming-Guang; Guo, Hui-Jun; Qi, Fei; Song, Qin-Hua

    2011-10-21

    A series of pyrene-centered starburst oligocarbazoles (1-3) have been synthesized and well characterized. Based on photophysical, thermal and electrochemical studies in solutions and as thin films, all starburst molecules reveal a sky blue emission with a high efficiency (Φ(F) = 0.99-0.81) and excellent thermal and electrochemical stabilities. As OLED materials, these superior properties are helpful to enhance device stability and lifetime.

  1. Test of Cable Products in Respect of Thermal and Dynamic Stability

    Directory of Open Access Journals (Sweden)

    M. A. Коrotkevich

    2010-01-01

    Full Text Available The paper considers conditions for selection of  power supply of the unit which is used for testing samples of cable products by thermal and dynamic stability currents. It has been shown that while conducting testing by thermal and dynamic stability currents at nominal cable voltage it is more justifiable to use a percussive energy accumulator, and in the case when the voltage is low an inductive energy accumulator is used.

  2. Introduction to the concept of thermal stability: expression of the general problem

    International Nuclear Information System (INIS)

    Llory, M.; Planchard, J.

    1981-01-01

    In the first part, an introduction is given to the concept of thermal stability, based firstly on experimental results and secondly on a simplified formulation of the problem. In the second part, the above considerations are generalized: the general problem of thermal stability is stated and it is shown that it can be considered as an eigenvalue problem. In the third part, a simple application of the general case is developed [fr

  3. Thermal Stability Test of Sugar Alcohols as Phase Change Materials for Medium Temperature Energy Storage Application

    OpenAIRE

    Solé, Aran; Neumann, Hannah; Niedermaier, Sophia; Cabeza, Luisa F.; Palomo, Elena

    2014-01-01

    Sugar alcohols are potential phase change materials candidates as they present high phase change enthalpy values, are non-toxic and low cost products. Three promising sugar-alcohols were selected: D-mannitol, myo-inositol and dulcitol under high melting enthalpy and temperature criterion. Thermal cycling tests were performed to study its cycling stability which can be determining when selecting the suitable phase change material. D-mannitol and dulcitol present poor thermal stability...

  4. Strategies To Increase the Thermal Stability of Truly Biomimetic Hydrogels: Combining Hydrophobicity and Directed Hydrogen Bonding

    OpenAIRE

    Yuan, Hongbo; Xu, Jialiang; van Dam, Eliane P.; Giubertoni, Giulia; Rezus, Yves L. A.; Hammink, Roel; Bakker, Huib J.; Zhan, Yong; Rowan, Alan E.; Xing, Chengfen; Kouwer, Paul H. J.

    2017-01-01

    Enhancing the thermal stability of proteins is an important task for protein engineering. There are several ways to increase the thermal stability of proteins in biology, such as greater hydrophobic interactions, increased helical content, decreased occurrence of thermolabile residues, or stable hydrogen bonds. Here, we describe a well-defined polymer based on β-helical polyisocyanotripeptides (TriPIC) that uses biological approaches, including hydrogen bonding and hydrophobic interactions fo...

  5. The Effect of pH and Color Stability of Anthocyanin on Food Colorant

    Science.gov (United States)

    Wahyuningsih, S.; Wulandari, L.; Wartono, M. W.; Munawaroh, H.; Ramelan, A. H.

    2017-04-01

    Anthocyanins are naturally occurring pigments of red and purple. Red anthocyanin pigments provide a strong and sharp and widely applied in various industries such as food coloring or drink. Anthocyanins isolated by maceration, extraction and thin layer chromatography (TLC). The extract has been obtained from the initial stages of maceration then separated into several fractions by chromatography to isolate fractions colored dark red. Identification of chemical compounds with TLC (Thin Layer Chromatography) is able to distinguish the fraction of anthocyanin produced. FTIR (Fourier Transform Infrared Spectroscopy) used to identification of the functional group of a compound. The UV-Vis absorption spectra have to produce maximum absorbance values that describe the intensity of anthocyanin spectra in different colors for different pH. Anthocyanins are more stable at low pH (acidic conditions) which gives a red pigment. Meanwhile, the higher the pH value of anthocyanin will provide color fading of the color blue. So as a food colorant, anthocyanin with a low pH or height pH has a significant effect on the food colorant.

  6. Glacial--interglacial stability of ocean pH inferred from foraminifer dissolution rates.

    Science.gov (United States)

    Anderson, David M; Archer, David

    2002-03-07

    The pH of the ocean is controlled by the chemistry of calcium carbonate. This system in turn plays a large role in regulating the CO2 concentration of the atmosphere on timescales of thousands of years and longer. Reconstructions of ocean pH and carbonate-ion concentration are therefore needed to understand the ocean's role in the global carbon cycle. During the Last Glacial Maximum (LGM), the pH of the whole ocean is thought to have been significantly more basic, as inferred from the isotopic composition of boron incorporated into calcium carbonate shells, which would partially explain the lower atmospheric CO2 concentration at that time. Here we reconstruct carbonate-ion concentration--and hence pH--of the glacial oceans, using the extent of calcium carbonate dissolution observed in foraminifer faunal assemblages as compiled in the extensive global CLIMAP data set. We observe decreased carbonate-ion concentrations in the glacial Atlantic Ocean, by roughly 20 micromolkg-1, while little change occurred in the Indian and Pacific oceans relative to today. In the Pacific Ocean, a small (5 micromolkg-1) increase occurred below 3,000m. This rearrangement of ocean pH may be due to changing ocean circulation from glacial to present times, but overall we see no evidence for a shift in the whole-ocean pH as previously inferred from boron isotopes.

  7. Purification and pH stability characterization of a chymotrypsin inhibitor from Schizolobium parahyba seeds.

    Science.gov (United States)

    Teles, Rozeni C L; de Souza, Elizabeth M T; Calderon, Leonardo de A; de Freitas, Sonia M

    2004-04-01

    Schizolobium parahyba chymotrypsin inhibitor (SPCI) was completely purified as a single polypeptide chain with two disulfide bonds, by TCA precipitation and ion exchange chromatography. This purification method is faster and more efficient than that previously reported: SPCI is stable from pH 2 to 12 at 25 degrees C, and is highly specific for chymotrypsin at pH 7-12. It weakly inhibits elastase and has no significant inhibitory effect against trypsin and alpha-amylase. SPCI is a thermostable protein and resists thermolysin digestion up to 70 degrees C.

  8. Thermal stability of double-ceramic-layer thermal barrier coatings with various coating thickness

    International Nuclear Information System (INIS)

    Dai Hui; Zhong Xinghua; Li Jiayan; Zhang Yanfei; Meng Jian; Cao Xueqiang

    2006-01-01

    Double-ceramic-layer (DCL) coatings with various thickness ratios composed of YSZ (6-8 wt.% Y 2 O 3 + ZrO 2 ) and lanthanum zirconate (LZ, La 2 Zr 2 O 7 ) were produced by the atmospheric plasma spraying. Chemical stability of LZ in contact with YSZ in DCL coatings was investigated by calcining powder blends at different temperatures. No obvious reaction was observed when the calcination temperature was lower than 1250 deg. C, implying that LZ and YSZ had good chemical applicability for producing DCL coating. The thermal cycling test indicate that the cycling lives of the DCL coatings are strongly dependent on the thickness ratio of LZ and YSZ, and the coatings with YSZ thickness between 150 and 200 μm have even longer lives than the single-layer YSZ coating. When the YSZ layer is thinner than 100 μm, the DCL coatings failed in the LZ layer close to the interface of YSZ layer and LZ layer. For the coatings with the YSZ thickness above 150 μm, the failure mainly occurs at the interface of the YSZ layer and the bond coat

  9. Analysis of Thermal Stability of Different Counter on 28nm FPGA

    DEFF Research Database (Denmark)

    Gupta, Daizy; Yadav, Amit; Hussain, Dil muhammed Akbar

    2016-01-01

    In this paper we are presenting the power analysis for thermal awareness of different counters. The technique we are using to do the analysis is based on 28 nm FPGA tech-nique. In this work during implementation on FPGA, we are going to analyze thermal stability of different counters in temperature...

  10. Enhancement of thermal stability of silver(I) acetylacetonate by platinum(II) acetylacetonate

    Czech Academy of Sciences Publication Activity Database

    Křenek, T.; Kovářík, T.; Pola, M.; Jakubec, Ivo; Bezdička, Petr; Bastl, Zdeněk; Pokorná, Dana; Urbanová, Markéta; Galíková, Anna; Pola, Josef

    2013-01-01

    Roč. 554, FEB (2013), s. 1-7 ISSN 0040-6031 Institutional support: RVO:61388980 ; RVO:61388955 ; RVO:67985858 Keywords : thermal gravimetric analysis * differential scanning calorimetry * silver(I) acetylacetonate * platinum(II) acetylacetonate * enhancement of thermal stability Subject RIV: CA - Inorganic Chemistry; CF - Physical ; Theoretical Chemistry (UFCH-W) Impact factor: 2.105, year: 2013

  11. Activation and thermal stability of ultra-shallow B+-implants in Ge

    DEFF Research Database (Denmark)

    Yates, B. R.; Darby, B. L.; Petersen, Dirch Hjorth

    2012-01-01

    The activation and thermal stability of ultra-shallow B+ implants in crystalline (c-Ge) and preamorphized Ge (PA-Ge) following rapid thermal annealing was investigated using micro Hall effect and ion beam analysis techniques. The residual implanted dose of ultra-shallow B+ implants in Ge was char...

  12. Thermal stability of porous sol-gel phosphosilicates and their surface area stabilisation by lanthanum addition

    NARCIS (Netherlands)

    Falco, Lorena; De Mendonca, Mariana Van Den Tempel; Mercadal, Juan J.; Zarubina, Valeriya; Melián-Cabrera, Ignacio

    2016-01-01

    The thermal stability of porous sol-gel phosphosilicates was studied by comparing the textural features upon calcination between 400 and 550 °C. A significant loss of surface area and pore volume were observed; the first is due to thermal coarsening of the nanoparticles, and the pore volume

  13. THERMAL STABILITY OF NICKEL AZIDES | Irom | Global Journal of ...

    African Journals Online (AJOL)

    . The samples, prepared using different methods, are fresh nickel azide, fresh nickel hydroxy axide and the third sample was obtained by ageing fresh nickel hydroxy azide for almost one year. Thermal decomposition of the samples at different ...

  14. Thermal Shock Resistance of Stabilized Zirconia/Metal Coat on Polymer Matrix Composites by Thermal Spraying Process

    Science.gov (United States)

    Zhu, Ling; Huang, Wenzhi; Cheng, Haifeng; Cao, Xueqiang

    2014-12-01

    Stabilized zirconia/metal coating systems were deposited on the polymer matrix composites by a combined thermal spray process. Effects of the thicknesses of metal layers and ceramic layer on thermal shock resistance of the coating systems were investigated. According to the results of thermal shock lifetime, the coating system consisting of 20 μm Zn and 125 μm 8YSZ exhibited the best thermal shock resistance. Based on microstructure evolution, failure modes and failure mechanism of the coating systems were proposed. The main failure modes were the formation of vertical cracks and delamination in the outlayer of substrate, and the appearance of coating spallation. The residual stress, thermal stress and oxidation of substrate near the substrate/metal layer interface were responsible for coating failure, while the oxidation of substrate near the substrate/coating interface was the dominant one.

  15. Effects of pH and additives on aqueous wetting films stabilized by a triblock copolymer

    NARCIS (Netherlands)

    Eliseeva, O.V.; Besseling, N.A.M.; Koopal, L.K.; Stuart, M.A.C.

    2007-01-01

    Effects of pH and additives (NaCl, Na2SO4, NaSCN and urea) on the adsorption of an ABA triblock copolymer (F127) with polyethylene oxide as the A blocks and polypropylene oxide as the B blocks, at the interfaces of wetting films, on film drainage and on the interaction forces in these films are

  16. Effect of Filler Concentration on Thermal Stability of Vinyl Copolymer Elastomer (VCE) Composites

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Dali [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hubbard, Kevin Mark [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Devlin, David James [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Henderson, Kevin C. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Pacheco, Robin Montoya [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-03-06

    To study the thermal stability of vinyl copolymer elastomer (VCE) in its composite form, systematic TGA characterizations were conducted in both nonisothermal and isothermal modes. The effects of filler concentration on the aging behaviors of the VCE/filler composites were investigated under nitroplasticizer (NP) environment. FTIR characterization was used to probe the structural changes in the VCE polymer before and after the thermal treatments. This study suggests that the filler concentration significantly deteriorates the thermal stability of NP at a moderate temperature (< 70 °C). The degradation of NP, in turn, accelerates the aging process of the VCE polymer in its composite form.

  17. Thermal Degradation Mechanism of a Thermostable Polyester Stabilized with an Open-Cage Oligomeric Silsesquioxane

    Directory of Open Access Journals (Sweden)

    Yolanda Bautista

    2017-12-01

    Full Text Available A polyester composite was prepared through the polymerization of an unsaturated ester resin with styrene and an open-cage oligomeric silsesquioxane with methacrylate groups. The effect of the open-cage oligomeric silsesquioxane on the thermal stability of the thermostable polyester was studied using both thermogravimetric analysis and differential thermal analysis. The results showed that the methacryl oligomeric silsesquioxane improved the thermal stability of the polyester. The decomposition mechanism of the polyester/oligomer silsesquioxane composite was proposed by Fourier transform infrared spectroscopy (FTIR analysis of the volatiles.

  18. Thermal Degradation Mechanism of a Thermostable Polyester Stabilized with an Open-Cage Oligomeric Silsesquioxane

    Science.gov (United States)

    Gozalbo, Ana; Mestre, Sergio; Sanz, Vicente

    2017-01-01

    A polyester composite was prepared through the polymerization of an unsaturated ester resin with styrene and an open-cage oligomeric silsesquioxane with methacrylate groups. The effect of the open-cage oligomeric silsesquioxane on the thermal stability of the thermostable polyester was studied using both thermogravimetric analysis and differential thermal analysis. The results showed that the methacryl oligomeric silsesquioxane improved the thermal stability of the polyester. The decomposition mechanism of the polyester/oligomer silsesquioxane composite was proposed by Fourier transform infrared spectroscopy (FTIR) analysis of the volatiles. PMID:29295542

  19. Thermal and stability considerations of super LWR during sliding pressure startup

    International Nuclear Information System (INIS)

    Yi Tin Tin; Ishiwatari, Yuki; Liu, Jie; Koshizuka, Seiichi; Oka, Yoshiaki

    2005-01-01

    The feasibility of the sliding pressure startup of a high-temperature supercritical-pressure light water reactor (super LWR, SCLWR-H) is assessed from both thermal and stability considerations. In the sliding pressure startup, nuclear heating starts at subcritical pressure and the reactor is pressurized to supercritical pressure at a low power and high enough flow rate. The reactor power and flow rate are then raised gradually to the rated normal values at constant supercritical operating pressure. During startup, the maximum cladding surface temperature must not exceed 620degC. For two-phase flow at subcritical pressures, the homogeneous equilibrium model is used. The thermal-hydraulic and coupled neutronic thermal-hydraulic stabilities during pressurization and power-raising are investigated by a frequency-domain linear analysis for both supercritical-pressure and subcritical-pressure operating conditions. The same stability criteria as those of BWRs are used. From the analysis results, a sliding pressure startup procedure is proposed for super LWR. The thermal criteria are satisfied by keeping the core power between the maximum allowable limit and minimum limit required for turbine startup and operation. The thermal-hydraulic stability and coupled neutronic thermal-hydraulic stability can be maintained by applying an orifice pressure drop coefficient at the inlet of fuel assembly and by controlling the power and flow rate during startup. (author)

  20. Effect of pH decline on foraminiferal stable isotopes during the Paleocene-Eocene Thermal Maximum?

    Science.gov (United States)

    Uchikawa, J.; Zeebe, R. E.

    2009-12-01

    Pioneering culture experiments by Spero et al. (1997) demonstrated that seawater pH (or carbonate chemistry) has a marked effect on planktonic foraminiferal stable oxygen and carbon isotopes (δ18O and δ13C). Both δ18O and δ13C become isotopically heavier as seawater pH decreases (the “pH effect”). Several studies now argue that δ18O and δ13C of benthic foraminifera are similarly influenced by the pH effect. As a result, paleooceanographic information based on foraminiferal δ18O and δ13C can be significantly biased for the time-window during which seawater pH was notably different from the modern condition or varied rapidly. A prime example of such is the Paleocene-Eocene Thermal Maximum (PETM). Widespread dissolution of sedimentary CaCO3 in the PETM strata (e.g., Zachos et al., 2005) suggests significant ocean acidification during this time interval. In this study, we examine the magnitude of the pH effect on foraminiferal δ18O and δ13C during the PETM. First we will estimate the relative pH decline from the pre-PETM steady state in the surface and deep ocean reservoirs in response to 2,000 ~ 5,000 Pg of carbon input using a carbon cycle model (Zeebe et al., 2009). We will then apply the empirical relationships obtained from the culture experiments by Spero et al. (1997) to calculate the ranges of errors in the foraminiferal δ18O and δ13C that could arise due to the pH effect during the PETM. {REFERENCES} Spero et al. (1997) Nature, v390, p497-500: Zachos et al. (2005) Science, v308, p1611-1615: Zeebe et al. (2009) Nature Geoscience, v2, p576-580.

  1. Global shape and pH stability of ovorubin, an oligomeric protein from the eggs of Pomacea canaliculata.

    Science.gov (United States)

    Dreon, Marcos S; Ituarte, Santiago; Ceolín, Marcelo; Heras, Horacio

    2008-09-01

    Ovorubin, a 300-kDa thermostable oligomer, is the major egg protein from the perivitellin fluid that surrounds the embryos of the apple snail Pomacea canaliculata. It plays essential roles in embryo development, including transport and protection of carotenoids, protease inhibition, photoprotection, storage, and nourishment. Here, we report ovorubin dimensions and global shape, and test the role of electrostatic interactions in conformational stability by analyzing the effects of pH, using small-angle X-ray scattering (SAXS), transmission electron microscopy, CD, and fluorescence and absorption spectroscopy. Analysis of SAXS data shows that ovorubin is an anisometric particle with a major axis of 130 A and a minor one varying between 63 and 76 A. The particle shape was not significantly affected by the absence of the cofactor astaxanthin. The 3D model presented here is the first for an invertebrate egg carotenoprotein. The quaternary structure is stable over a wide pH range (4.5-12.0). At a pH between 2.0 and 4.0, a reduction in the gyration radius and a loss of tertiary structure are observed, although astaxanthin binding is not affected and only minor alterations in secondary structure are observed. In vitro pepsin digestion indicates that ovorubin is resistant to this protease action. The high stability over a considerable pH range and against pepsin, together with the capacity to bear temperatures > 95 degrees C, reinforces the idea that ovorubin is tailored to withstand a wide variety of conditions in order to play its key role in embryo protection during development.

  2. Effect of the fermentation pH on the storage stability of Lactobacillus rhamnosus preparations and suitability of in vitro analyses of cell physiological functions to predict it.

    Science.gov (United States)

    Saarela, M H; Alakomi, H-L; Puhakka, A; Mättö, J

    2009-04-01

    To investigate how cell physiological functions can predict the stability of freeze-dried probiotics. In addition, the effect of the fermentation pH on the stability of probiotics was investigated. Fermenter-grown (pH 5.8 or 5.0) Lactobacillus rhamnosus cells were freeze-dried and their survival was evaluated during storage at 37 degrees C, in apple juice and during acid [hydrochloric acid (HCl) and malic acid] and bile exposure. Cells grown at pH 5.0 were generally coping better with acid-stress than cells grown at pH 5.8. Cells were more sensitive to malic acid compared with HCl. Short-term stability results of Lact. rhamnosus cells in malic acid correlated well with the long-term stability results in apple juice, whereas the results of cell membrane integrity studies were in accordance with bile exposure results. Malic acid exposure can prove useful in evaluating the long-term stability of probiotic preparations in apple juice. Fermentation at reduced pH may ensure a better performance of Lact. rhamnosus cells during the subsequent acid-stress. The beneficial effect of lowered fermentation pH to Lact. rhamnosus stability during storage in apple juice and the usefulness of malic acid test in predicting the stability were shown.

  3. Thermal stability of phenolic based binders and frictional performance of brake composite materials

    Science.gov (United States)

    Pudhota, Madhuri

    To enhance frictional performance, wear and to obtain improved thermal stability with a reduction of noise, vibration, and harshness (NVH) and provide environment friendly brakes for the increasing needs of the population's comfort and safety requirements this study was initiated. The thermal stability of two different phenolic resins as binder on the frictional performance of brake composite material was studied. The two phenolic resins used are Durite phenolic resin and Bakelite phenolic resins. They were tested for friction, wear, thermal stability and degradation. This was executed by using a universal friction tester (UFT) for testing friction and wear, then on thermo gravimetric analysis (TGA) and the TGA results indicate more mass loss of NB samples contrary to test results. When individual materials were heated, Bakelite lost less mass compared to Durite. The friction test indicates more friction when used the NB samples but they had less wear and more stability nevertheless this could vary for other compositions and conditions.

  4. Effect of thermal aging on stability of transformer oil based temperature sensitive magnetic fluids

    Science.gov (United States)

    Kaur, Navjot; Chudasama, Bhupendra

    2018-04-01

    Synthesizing stable temperature sensitive magnetic fluids with tunable magnetic properties that can be used as coolant in transformers is of great interest, however not exploited commercially due to the lack of its stability at elevated temperatures in bulk quantities. The task is quite challenging as the performance parameters of magnetic fluids are strongly influenced by thermal aging. In this article, we report the effect of thermal aging on colloidal stability and magnetic properties of Mn1-xZnxFe2O4 magnetic fluids prepared in industrial grade transformer oil. As-synthesized magnetic fluids possess good dispersion stability and tunable magnetic properties. Effect of accelerated thermal aging on the dispersion stability and magnetic properties have been evaluated by photon correlation spectroscopy and vibration sample magnetometry, respectively. Magnetic fluids are stable under accelerated aging at elevated temperatures (from 50 °C to 125 °C), which is critical for their efficient performance in high power transformers.

  5. pH regulation of the kinetic stability of the lipase from Thermomyces lanuginosus

    DEFF Research Database (Denmark)

    Wang, H.; Andersen, Kell Kleiner; Sehgal, P.

    2013-01-01

    Thermomyces lanuginosus lipase (TlL) is a kinetically stable protein, resistant toward both denaturation and refolding in the presence of the ionic surfactant sodium dodecyl sulfate (SDS) and the nonionic surfactant decyl maltoside (DecM). We investigate the pH dependence of this kinetic stabilit...... but not sufficient feature of SDS resistance, because this has to be combined with sufficient negative electrostatic potential to avoid extensive SDS binding....

  6. Fabrication, thermal properties and thermal stabilities of microencapsulated n-alkane with poly(lauryl methacrylate) as shell

    Energy Technology Data Exchange (ETDEWEB)

    Qiu, Xiaolin, E-mail: shirleyqiu2009@gmail.com [Jiangsu Key Laboratory of Advanced Food Manufacturing Equipment and Technology, School of Mechanical Engineering, Jiangnan University, Wuxi 214122 (China); Lu, Lixin; Wang, Ju [Jiangsu Key Laboratory of Advanced Food Manufacturing Equipment and Technology, School of Mechanical Engineering, Jiangnan University, Wuxi 214122 (China); Tang, Guoyi [Advanced Materials Institute and Clearer Production Key Laboratory, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); Key Laboratory of Advanced Materials, Department of Materials Science and Engineering, Tsinghua University, Haidian District, Beijing 100084 (China); Song, Guolin [Advanced Materials Institute and Clearer Production Key Laboratory, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China)

    2015-11-20

    Highlights: • Microencapsulation of octadecane and paraffin by crosslinked poly(lauryl methacrylate). • Octadecane microcapsules have a melting enthalpy of about 118 J g{sup −1}. • Weight loss temperatures of the microcapsules were increased by 67 °C and 28 °C. • Phase change enthalpies decreased by around 10 wt% after 500 thermal cycles. • Foams with microcapsules can be applied for passive temperature control. - Abstract: Microencapsulation of n-octadecane or paraffin with poly(lauryl methacrylate) (PLMA) shell was performed by a suspension-like polymerization. The polymer shell was crosslinked by pentaerythritol tetraacrylate (PETRA). The surface morphologies of microcapsules were investigated by scanning electron microscopy (SEM). Phase change properties, thermal reliabilities and thermal stabilities of microcapsules were determined by differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA). The n-octadecane microcapsule exhibits higher melting enthalpy (118.0 J g{sup −1}) and crystallization enthalpy (108.3 J g{sup −1}) compared with the paraffin microcapsule. The thermal resistant temperatures were enhanced by more than 25 °C when n-alkanes were microencapsulated by PLMA. The PCM contents of microcapsules decreased by less than 4 wt% and 6 wt% after 500 and 1000 thermal cycles, respectively. Heat-up experiments indicated that microcapsule-treated foams exhibited upgraded thermal regulation capacities. Consequently, microencapsulated n-octadecane or paraffin with PLMA as shell possesses good potentials for heat storage and thermal regulation.

  7. Fabrication, thermal properties and thermal stabilities of microencapsulated n-alkane with poly(lauryl methacrylate) as shell

    International Nuclear Information System (INIS)

    Qiu, Xiaolin; Lu, Lixin; Wang, Ju; Tang, Guoyi; Song, Guolin

    2015-01-01

    Highlights: • Microencapsulation of octadecane and paraffin by crosslinked poly(lauryl methacrylate). • Octadecane microcapsules have a melting enthalpy of about 118 J g −1 . • Weight loss temperatures of the microcapsules were increased by 67 °C and 28 °C. • Phase change enthalpies decreased by around 10 wt% after 500 thermal cycles. • Foams with microcapsules can be applied for passive temperature control. - Abstract: Microencapsulation of n-octadecane or paraffin with poly(lauryl methacrylate) (PLMA) shell was performed by a suspension-like polymerization. The polymer shell was crosslinked by pentaerythritol tetraacrylate (PETRA). The surface morphologies of microcapsules were investigated by scanning electron microscopy (SEM). Phase change properties, thermal reliabilities and thermal stabilities of microcapsules were determined by differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA). The n-octadecane microcapsule exhibits higher melting enthalpy (118.0 J g −1 ) and crystallization enthalpy (108.3 J g −1 ) compared with the paraffin microcapsule. The thermal resistant temperatures were enhanced by more than 25 °C when n-alkanes were microencapsulated by PLMA. The PCM contents of microcapsules decreased by less than 4 wt% and 6 wt% after 500 and 1000 thermal cycles, respectively. Heat-up experiments indicated that microcapsule-treated foams exhibited upgraded thermal regulation capacities. Consequently, microencapsulated n-octadecane or paraffin with PLMA as shell possesses good potentials for heat storage and thermal regulation.

  8. Distribution of chloride, pH, resistivity, and sulfate levels in backfill for mechanically-stabilized earth walls and implications for corrosion testing.

    Science.gov (United States)

    2015-05-01

    The ultimate goals of this research were to improve quality, speed completion, and reduce risk in mechanically-stabilized : earth (MSE) wall projects. Research objectives were to assure (1) that variability in the corrosion properties of soil (pH, : ...

  9. Heat conduction and thermal stabilization in YBCO tape

    Indian Academy of Sciences (India)

    †Shibli National College, Azamgarh 276 131, India. MS received 20 April 2011; ... profile along the length of HTS tape under a given energy (joule heating) such that propagation of the hot spot devel- oped locally can be prevented ... diction is best described by carrying out a thermal conduc- tion of the initial quench zone ...

  10. A Study of Strong Stability of Distributed Systems. Ph.D. Thesis

    Science.gov (United States)

    Cataltepe, Tayfun

    1989-01-01

    The strong stability of distributed systems is studied and the problem of characterizing strongly stable semigroups of operators associated with distributed systems is addressed. Main emphasis is on contractive systems. Three different approaches to characterization of strongly stable contractive semigroups are developed. The first one is an operator theoretical approach. Using the theory of dilations, it is shown that every strongly stable contractive semigroup is related to the left shift semigroup on an L(exp 2) space. Then, a decomposition for the state space which identifies strongly stable and unstable states is introduced. Based on this decomposition, conditions for a contractive semigroup to be strongly stable are obtained. Finally, extensions of Lyapunov's equation for distributed parameter systems are investigated. Sufficient conditions for weak and strong stabilities of uniformly bounded semigroups are obtained by relaxing the equivalent norm condition on the right hand side of the Lyanupov equation. These characterizations are then applied to the problem of feedback stabilization. First, it is shown via the state space decomposition that under certain conditions a contractive system (A,B) can be strongly stabilized by the feedback -B(*). Then, application of the extensions of the Lyapunov equation results in sufficient conditions for weak, strong, and exponential stabilizations of contractive systems by the feedback -B(*). Finally, it is shown that for a contractive system, the first derivative of x with respect to time = Ax + Bu (where B is any linear bounded operator), there is a related linear quadratic regulator problem and a corresponding steady state Riccati equation which always has a bounded nonnegative solution.

  11. Sterculia striata seed kernel oil: Characterization and thermal stability

    Directory of Open Access Journals (Sweden)

    Oliveira Cavalheiro, José Marcelino

    2008-06-01

    Full Text Available The objective of the present work was to characterize sterculia seed kernel oil. The chemical composition of the seeds, physicochemical properties as well as the fatty acid composition of the kernel oil was determined. The chemical composition of kernel flour presented about 25.8% lipid content. The physicochemical parameters such as acid, iodine, peroxide and saponification values were 0.82 (% as oleic acid, 69.2 (g iodine/100 g oil, 4.20 (m eq./kg and 136.1 (mg. KOH/g oil, respectively. With respect to fatty acid composition, the oil contained 36.2, 43.7 and 10.9% saturated, monounsaturated and polyunsaturated fatty acids, respectively. Palmitic acid (31.9%, oleic acid (41.7% and linoleic acid (10.73% were the principal saturated, monounsaturated and polyunsaturated fatty acids. Two cyclopropanoid fatty acids i.e. sterculic and malvalic acid were identified at a concentration of 5.3 and 2.3%, respectively. With regards to the thermal stability of the oil, a thermogravimetric analysis (TGA has shown that the oil was stable until about 284 °C, above that the oil started loosing mass, while a differential thermogravimetric analysis (DTGA revealed three stages of degradation with an increase in temperature. These stages corresponded to the degradation of polyunsaturated, monounsaturated and saturated fatty aids. The Differential Scanning Calorimetric (DSC analysis showed the existence of two exothermic events of energy transition, one of which is related to the oxidation reactions and another to the decomposition of the oil. Exothermic transitions in the oil were initiated at a temperature (Ti of 287.79 °C, and terminated at 347.81 °C, with an enthalpy variation of 11.69 joules.g–1 and at initial temperature (Ti of 384.87 °C, peak temperature (Tp 415.71 °C, final temperature (Tf 448.9 °C and an enthalpy of 200.83 Joules. G–1El objetivo de este trabajo fue la caracterización del aceite de almendra de la semilla de

  12. Fabrication and thermal stability studies of polyamide 66 containing ...

    Indian Academy of Sciences (India)

    During fabrication of FR-PA66, melt polymerization time exhibits more surprising influence on intrinsic viscosity than aqueous solution polymerization time. The LOI value of FR-PA66 with 9 wt% TPO reaches 27.2, and corresponding UL94 rating reaches V-0. Improved thermo-stability of FR-PA66 can be attributed to both ...

  13. Strength and thermal stability of fiber reinforced plastic composites ...

    African Journals Online (AJOL)

    Flexural tests and dimensional stability (water absorption and thickness swelling) of the rattan composites were determined. The results obtained revealed that the rattan composites possessed adequate strength and had low water absorption and thickness swelling rates. The water absorption of the composites was ...

  14. Effect of salt and acidic pH on the stability of virulence plasmid (pYV) in Yersinia enterocolitica and expression of virulence-associated characteristics

    Science.gov (United States)

    The stability of the Yersinia enterocolitica virulence plasmid (pYV) under different NaCl concentrations and under acidic pH conditions was investigated. Exposure of five strains representing five serotypes of pYV-bearing virulent Y. enterocolitica to 0.5, 2 and 5% NaCl and under conditions of pH 4...

  15. Thermal stability in a newly designed columnar-conical fluidized bed for combustion of rice husk

    Energy Technology Data Exchange (ETDEWEB)

    Rozainee, M.; Salema, A.A.; Ngo, S.P.; Chye, G.B. [Malaysian Technological Univ., Johor Bahru (Malaysia). Dept. of Chemical Engineering

    2006-07-01

    The effects of fluidizing and liquid propane gas (LPG) flow rates on thermal stability of a fluidized bed were examined. The aim of the study was to hybridize a columnar and conical fluidized bed (CCFB) in order to encourage the combustion of low-calorific fuels such as rice husks. Experiments were conducted to examine the thermal stability of the CCFB. Premixed primary air and liquid propane gas (LPG) was fed into the bed in order to verify its thermal stability. Temperature profiles of the combustor and bed were measured. The impact of the fluidizing velocity and LPG flow rate on the temperature profile was examined in order to analyze the influence of the fluidizing velocity and LPG rate on combustion rates. Results of the study showed that the combustion of the CCFB was sustained at a fluidizing velocity of 1.5 U{sub mf} and at an LPG flow rate of 8 liters per minute. Results of the study showed that fluidizing velocity played an important role on the thermal stability of the bed. It was concluded that the thermal stability of the combustor is sufficient for the CCFB. 13 refs., 2 tabs., 5 figs.

  16. Thermal stability of butter oils produced from sheep’s non-pasteurized and pasteurized milk

    Directory of Open Access Journals (Sweden)

    FLAVIA POP

    Full Text Available The physical and chemical characteristics and thermal stability of butter oil produced from non-pasteurized and pasteurized sheep’s milk were studied. Thermal stability of samples was estimated by using the accelerated shelf-life testing method. Samples were stored at 50, 60 and 70oC in the dark and the reaction was monitored by measuring peroxide, thiobarbituric acid and free fatty acid values. The peroxide and thiobarbituric acid values increased as the temperature increased. The increase of acid values of the two samples was not significant. A slight increase in free fatty acid value showed that hydrolytic reactions were not responsible for the deterioration of butter oil samples in thermal stability studies. When compared, butter oil produced from pasteurized sheep’s milk has higher thermal stability than butter oil produced from non-pasteurized sheep’s milk. Although butter oil produced from non-pasteurized milk was not exposed to any heat treatment, the shelf-life of this product was lower than the shelf-life of butter oil produced from pasteurized sheep’s milk. Therefore, heat treatment for pasteurization did not affect the thermal stability of butter oil.

  17. CONTROL AND STABILITY ANALYSIS OF THE GMC ALGORITHM APPLIED TO pH SYSTEMS

    Directory of Open Access Journals (Sweden)

    Manzi J.T.

    1998-01-01

    Full Text Available This paper deals with the control of the neutralization processes of the strong acid-strong base and the weak acid-strong base systems using the Generic Model Control (GMC algorithm. The control strategy is applied to a pilot plant where hydrochloric acid-sodium hydroxide and acetic acid-sodium hydroxide systems are neutralized. The GMC algorithm includes in the controller structure a nonlinear model of the process in the controller structure. The paper also focuses the provides a stability analysis of the controller for some of the uncertainties involved in the system. The rResults indicate that the controller stabilizes the system for a large range of uncertainties, but the performance may deteriorate when the system is submitted to large disturbances.

  18. Engineering a highly active thermophilic ?-glucosidase to enhance its pH stability and saccharification performance

    OpenAIRE

    Xia, Wei; Xu, Xinxin; Qian, Lichun; Shi, Pengjun; Bai, Yingguo; Luo, Huiying; Ma, Rui; Yao, Bin

    2016-01-01

    Background ?-Glucosidase is an important member of the biomass-degrading enzyme system, and plays vital roles in enzymatic saccharification for biofuels production. Candidates with high activity and great stability over high temperature and varied pHs are always preferred in industrial practice. To achieve cost-effective biomass conversion, exploring natural enzymes, developing high level expression systems and engineering superior mutants are effective approaches commonly used. Results A new...

  19. Thermal stability of nanocrystalline ε-Fe2O3

    Czech Academy of Sciences Publication Activity Database

    Brázda, Petr; Večerníková, Eva; Pližingrová, Eva; Lančok, Adriana; Nižňanský, D.

    2014-01-01

    Roč. 117, č. 1 (2014), s. 85-91 ISSN 1388-6150 R&D Projects: GA ČR GAP204/10/0035 Institutional support: RVO:61388980 Keywords : ε-Fe2O3 * Differential thermal analysis * Evolved gas analysis * Infrared spectroscopy * Thermogravimetry * X-ray powder diffraction Subject RIV: CA - Inorganic Chemistry Impact factor: 2.042, year: 2014

  20. Stability, rheology and thermal analysis of functionalized alumina- thermal oil-based nanofluids for advanced cooling systems

    International Nuclear Information System (INIS)

    Ilyas, Suhaib Umer; Pendyala, Rajashekhar; Narahari, Marneni; Susin, Lim

    2017-01-01

    Highlights: • Alumina nanoparticles are functionalized with oleic acid. • Functionalization of alumina nanoparticles gives better dispersion in thermal oil. • Thermophysical properties of nanofluids are experimentally measured. • TGA confirms the improvement in life of nanofluids. - Abstract: Thermal oils are widely used as cooling media in heat transfer processes. However, their potential has not been utilised exquisitely in many applications due to low thermal properties. Thermal oil-based nanofluids are prepared by dispersing functionalized alumina with varying concentrations of 0.5–3 wt.% to enhance thermal properties of oil for advanced cooling systems. The oleic acid coated alumina is prepared and then dispersed in the oil to overcome the aggregation of nanoparticles in base fluid. The surface characterizations of functionalized nanoparticles are performed using different analysis such as XRD, EDS, SEM, TEM and FTIR. Dispersion behaviour and agglomeration studies are conducted at natural and functionalized conditions using different analysis to ensure long-term stability of nanofluids. In addition, rheological behaviour of non-Newtonian nanofluids is studied at high shear rates (100–2000 s −1 ). Effective densities and enhancement in thermal conductivities are measured for different nanofluids concentrations. Specific heat capacity is measured using Differential Scanning Calorimetry. The correlations are developed for thermophysical properties of nanofluids. Thermogravimetric analysis is performed with respect to temperature and time to exploit the effect of the addition of nanoparticles on the degradation of nanofluids. Significant improvement in the thermal properties of oil is observed using highly stable functionalized alumina nano-additives.

  1. Thermal stability study for candidate stainless steels of GEN IV reactors

    Energy Technology Data Exchange (ETDEWEB)

    Simeg Veternikova, J., E-mail: jana.veternikova@stuba.sk [Institute of Nuclear and Physical Engineering, Faculty of Electrical and Information Technology, Slovak University of Technology, Ilkovicova 3, 812 19 Bratislava (Slovakia); Degmova, J. [Institute of Nuclear and Physical Engineering, Faculty of Electrical and Information Technology, Slovak University of Technology, Ilkovicova 3, 812 19 Bratislava (Slovakia); Pekarcikova, M. [Institute of Materials Science, Faculty of Materials Science and Technology, Slovak University of Technology, Paulinska 16, 917 24 Trnava (Slovakia); Simko, F. [Department of Molten Salts, Institute of Inorganic Chemistry, Slovak Academy of Sciences, Dubravska cesta 9, 845 36 Bratislava (Slovakia); Petriska, M. [Institute of Nuclear and Physical Engineering, Faculty of Electrical and Information Technology, Slovak University of Technology, Ilkovicova 3, 812 19 Bratislava (Slovakia); Skarba, M. [Slovak University of Technology, Vazovova 5, 812 43 Bratislava (Slovakia); Mikula, P. [Institute of Nuclear and Physical Engineering, Faculty of Electrical and Information Technology, Slovak University of Technology, Ilkovicova 3, 812 19 Bratislava (Slovakia); Pupala, M. [Department of Molten Salts, Institute of Inorganic Chemistry, Slovak Academy of Sciences, Dubravska cesta 9, 845 36 Bratislava (Slovakia)

    2016-11-30

    Highlights: • Thermal resistance of advanced stainless steels were observed at 1000 °C. • GEN IV candidate steels were confronted to classic AISI steels. • ODS AISI 316 has weaker thermal resistance than classic AISI steel. • Ferritic ODS steels and NF 709 has better thermal resistance than AISI steels. - Abstract: Candidate stainless steels for GEN IV reactors were investigated in term of thermal and corrosion stability at high temperatures. New austenitic steel (NF 709), austenitic ODS steel (ODS 316) and two ferritic ODS steels (MA 956 and MA 957) were exposed to around 1000 °C in inert argon atmosphere at pressure of ∼8 MPa. The steels were further studied in a light of vacancy defects presence by positron annihilation spectroscopy and their thermal resistance was confronted to classic AISI steels. The thermal strain supported a creation of oxide layers observed by scanning electron microscopy (SEM).

  2. Preparation, characterization and thermal stability of bentonite modified with bis-imidazolium salts

    Energy Technology Data Exchange (ETDEWEB)

    Makhoukhi, B., E-mail: benamarmakh@yahoo.fr [Laboratory of Separation and Purification Technologies, Department of Chemistry, Tlemcen University, Box 119, Tlemcen (Algeria); Villemin, D. [Laboratoire de Chimie Moléculaire et Thio-organique, UMR CNRS 6507, INC3M, FR 3038, ENSICAEN and Université de Caen, 14050 Caen (France); Didi, M.A. [Laboratory of Separation and Purification Technologies, Department of Chemistry, Tlemcen University, Box 119, Tlemcen (Algeria)

    2013-02-15

    Sodium bentonite was modified with several organic bis-imidazolium salts. Organoclays with water soluble surfactants were prepared by the traditional cation exchange reaction. The bis-imidazolium-bentonites were characterized by Fourier transform infrared spectroscopy (FTIR), powder X-ray diffraction analysis (PXRD) and thermogravimetric analysis (TGA). The effect of chemical composition and molecular weight of the salts on the thermal stability and basal spacing were evaluated. The bis-imidazolium-bentonites showed enhanced thermal stability (300–400 °C) and may be potentially useful materials for melt processing of polymer/layered silicates nanocomposites. - Highlights: ► Geometry and volume of the molecule influence on interlayer spacing of modified bentonites. ► The intercalation increases with molecule length. ► The modified bentonites have an appreciably higher thermal stability.

  3. [THERMAL STABILITY AS A PROGNOSTIC INDICATOR OF CONSERVATION OF LIVE EMBRYONIC SMALLPOX VACCINE (TEOVAC) DURING STORAGE].

    Science.gov (United States)

    Zhukov, V A; Kokorev, S V; Rogozhkina, S V; Melnikov, D G; Terentiev, A I; Kovalchuk, E A; Vakhnov, E Yu; Borisevich, S V

    2016-01-01

    Determination of values of coefficients of thermal stability of TEOVac for prognosis of conservation of the vaccine (specific biological activity) during the process of warranty period storage. TEOVac (masticatory tablets) in primary packaging was kept at increased temperature (accelerated and stress-tests) and at the conditions established by PAP for the preparation (long-term tests). Biological activity of the vaccine was determined by titration on 12-day chicken embryos. A correlation between the value of coefficients of thermal stability and conservation of the prepared series of the condition preparation at the final date of storage was experimentally established. Coefficients of thermal stability could be used as a prognostic indicator of quality of the produced pelleted formulation of the preparation for evaluation of conservation of the vaccine during warranty period storage.

  4. Thermal stability and primary phase of Al-Ni(Cu)-La amorphous alloys

    International Nuclear Information System (INIS)

    Huang Zhenghua; Li Jinfu; Rao Qunli; Zhou Youhe

    2008-01-01

    Thermal stability and primary phase of Al 85+x Ni 9-x La 6 (x = 0-6) and Al 85 Ni 9-x Cu x La 6 (x = 0-9) amorphous alloys were investigated by X-ray diffraction and differential scanning calorimeter. It is revealed that replacing Ni in the Al 85 Ni 9 La 6 alloy by Cu decreases the thermal stability and makes the primary phase change from intermetallic compounds to single fcc-Al as the Cu content reaches and exceeds 4 at.%. When the Ni and La contents are fixed, replacing Al by Cu increases the thermal stability but also promotes the precipitation of single fcc-Al as the primary phase

  5. Thermal and pH stabilities of partially purified polyphenol oxidase ...

    African Journals Online (AJOL)

    Dr. Paul Chidoka Chikezie

    2012-07-30

    Jul 30, 2012 ... 4(2):115-124. da Silva CR, Koblitz MGB (2010). Partial characterization and inactivation of peroxidases and polyphenol-oxidases of Umbu-Cajá. (Spondias spp.). Ciência e Tecnologia de Alimentos. 30(3):11. Dogan S, Dogan M (2004). Determination of kinetic properties of polyphenol oxidase from Thymus ...

  6. Lattice position and thermal stability of diluted As in Ge

    CERN Document Server

    Decoster, S; Cottenier, S; Correia, JG; Mendonça, T; Amorim, LM; Pereira, LMC; Vantomme, A

    2012-01-01

    We present a lattice location study of the n-type dopant arsenic after ion implantation into germanium. By means of electron emission channeling experiments, we have observed that the implanted As atoms substitute the Ge host atoms. However, in contrast to several implanted metal impurities in Ge, no significant fraction of As is found on interstitial sites. The substitutional As impurities are found to be thermally stable up to 600°C. After 700°C annealing a strong reduction of emission channeling effects was observed, in full accordance with the expected diffusion-induced broadening of the As profile.

  7. Grain boundary engineering to enhance thermal stability of electrodeposited nickel

    DEFF Research Database (Denmark)

    Alimadadi, Hossein

    by miniaturization of the grains down to nano-meter scale. However, this augments the total grain boundary energy stored in the material, hence, making the material less thermally stable. Coherent twin boundaries are of very low energy and mobility compared to all other boundaries in a FCC material. Accordingly...... interest. The evolution of microstructure in as-deposited and annealed condition was investigated with a combination of complementary microscopic techniques, electron backscatter diffraction (EBSD), electron channelling contrast imaging (ECCI), ion channelling contrast imaging (ICCI), and, for the as...

  8. The influence of polyol type on cell geometry and the thermal stability of polyurethane foams

    Directory of Open Access Journals (Sweden)

    Prendžov Slobodan J.

    2006-01-01

    Full Text Available The aim of this study was to examine the influence of substituting defined amounts of polyol Voranol 3322 by polyol Voranol CP 1055 on the cell geometry and thermal stability of the synthesized flexible polyurethane foams. The influence of the amount of antipyrene on the cell geometry and their thermal stability was also investigated. The following components were used in the synthesis of the polyurethanes: a mixture of two polyols (Voranol 3322 with the hydroxyl number 47 mg KOH/g, mean molecular mass 3400 and Voranol CP 1055 with the hydroxyl number 156 mg KOH/g, mean molecular mass 1000, toluene discarnate as the isocyanate component, a combination of an organic-metallic compound and a tertiary amine as catalysts, surfactant and water as the coreactant. The thermal stability was determined by thermogravimetric analysis (in a nitrogen atmosphere. The cell geometry was analyzed by optical microscopy. Examination of the cell geometry revealed different cell shapes. The form factor as an indicator of cell deviation from spherical shape increased (more round forms were observed with increasing amount of Voranol CP 1055. The TG examination showed that specimens with 6 and 8 g of Voranol 3322 substituted by Voranol CP 1055 completely degraded at 350 °C, while foams with 10 and 12 g of Voranol 3322 substituted by Voranol CP 1055 displayed lower mass loss at higher temperatures and had residual masses of 46 % and 43 % at 600°C respectively. The addition of antipyrene in an amount of 1% (based on the amount of polyol contributed to improved thermal stability, no visible color change of the specimen tested at 210°C for 40 minutes, and to rounder cell forms. Considering the obtained results it can be concluded that an increase in the amount of Voranol CP 1055 yielded more spherically shaped cells and better thermal stability of the synthesized flexible polyurethane foams. The addition of antipyrene improves the thermal stability and the cell geometry.

  9. Influence of Sonication on the Stability and Thermal Properties of Al2O3 Nanofluids

    Directory of Open Access Journals (Sweden)

    Monir Noroozi

    2014-01-01

    Full Text Available Nanofluids containing Al2O3 nanoparticles (either 11 or 30 nm in size dispersed in distilled water at low concentrations (0.125–0.5 wt% were prepared using two different ultrasonic devices (a probe and a bath sonicator as the dispersant. The effect of the ultrasonic system on the stability and thermal diffusivity of the nanofluids was investigated. Thermal diffusivity measurements were conducted using a photopyroelectric technique. The dispersion characteristics and morphology of the nanoparticles, as well as the optical absorption properties of the nanofluids, were studied using photon cross correlation spectroscopy with a Nanophox analyzer, transmission electron microscopy, and ultraviolet-visible spectroscopy. At higher particle concentration, there was greater enhancement of the thermal diffusivity of the nanofluids resulting from sonication. Moreover, greater stability and enhancement of thermal diffusivity were obtained by sonicating the nanofluids with the higher power probe sonicator prior to measurement.

  10. Influence of Carbon Nanotubes on Thermal Stability of Water-Dispersible Nanofibrillar Polyaniline/Nanotube Composite

    Directory of Open Access Journals (Sweden)

    Zhi-Bin Zhang

    2012-02-01

    Full Text Available Significant influence on the thermal stability of polyaniline (PANI in the presence of multi-walled carbon nanotubes (MWCNTs is reported. By means of in-situ rapid mixing approach, water-dispersible nanofibrillar PANI and composites, consisting of MWCNTs uniformly coated with PANI in the state of emeraldine salt, with a well-defined core-shell heterogeneous structure, were prepared. The de-protonation process in PANI occurs at a lower temperature under the presence of MWCNTs on the polyaniline composite upon thermal treatment. However, it is found that the presence of MWCNTs significantly enhances the thermal stability of PANI’s backbone upon exposure to laser irradiation, which can be ascribed to the core-shell heterogeneous structure of the composite of MWCNTs and PANI, and the high thermal conductivity of MWCNTs.

  11. Thermal stability of the krypton Hall effect thruster

    Directory of Open Access Journals (Sweden)

    Szelecka Agnieszka

    2017-03-01

    Full Text Available The Krypton Large IMpulse Thruster (KLIMT ESA/PECS project, which has been implemented in the Institute of Plasma Physics and Laser Microfusion (IPPLM and now is approaching its final phase, was aimed at incremental development of a ~500 W class Hall effect thruster (HET. Xenon, predominantly used as a propellant in the state-of-the-art HETs, is extremely expensive. Krypton has been considered as a cheaper alternative since more than fifteen years; however, to the best knowledge of the authors, there has not been a HET model especially designed for this noble gas. To address this issue, KLIMT has been geared towards operation primarily with krypton. During the project, three subsequent prototype versions of the thruster were designed, manufactured and tested, aimed at gradual improvement of each next exemplar. In the current paper, the heat loads in new engine have been discussed. It has been shown that thermal equilibrium of the thruster is gained within the safety limits of the materials used. Extensive testing with both gases was performed to compare KLIMT’s thermal behaviour when supplied with krypton and xenon propellants.

  12. Thermal Stability Limits of Imidazolium Ionic Liquids Immobilized on Metal-Oxides.

    Science.gov (United States)

    Babucci, Melike; Akçay, Aslı; Balci, Volkan; Uzun, Alper

    2015-08-25

    Thermal stability limits of 33 imidazolium ionic liquids (ILs) immobilized on three of the most commonly used high surface area metal-oxides, SiO2, γ-Al2O3, and MgO, were investigated. ILs were chosen from a family of 13 cations and 18 anions. Results show that the acidity of C2H of an imidazolium ring is one of the key factors controlling the thermal stability. An increase in C2H bonding strength of ILs leads to an increase in their stability limits accompanied by a decrease in interionic energy. Systematic changes in IL structure, such as changes in electronic structure and size of anion/cation, methylation on C2 site, and substitution of alkyl groups on the imidazolium ring with functional groups have significant effects on thermal stability limits. Furthermore, thermal stability limits of ILs are influenced strongly by acidic character of the metal-oxide surface. Generally, as the point of zero charge (PZC) of the metal-oxide increases from SiO2 to MgO, the interactions of IL and metal-oxide dominate over interionic interactions, and metal-oxide becomes the significant factor controlling the stability limits. However, thermal stability limits of some ILs show the opposite trend, as the chemical activities of the cation functional group or the electron donating properties of the anion alter IL/metal-oxide interactions. Results presented here can help in choosing the most suitable ILs for materials involving ILs supported on metal-oxides, such as for supported ionic liquid membranes (SILM) in separation applications or for solid catalyst with ionic liquid layer (SCILL) and supported ionic liquid phase (SILP) catalysts in catalysis.

  13. Thermal stability of soils and detectability of intrinsic soil features

    Science.gov (United States)

    Siewert, Christian; Kucerik, Jiri

    2014-05-01

    Soils are products of long term pedogenesis in ecosystems. They are characterized by a complex network of interactions between organic and inorganic constituents, which influence soil properties and functions. However, the interrelations cannot easily be determined. Our search for unifying principles of soil formation focuses on water binding. This approach was derived from water-dependent soil formation. It considers the importance of water binding in theories about the origin of genes, in the structural arrangement and functionality of proteins, and in the co-evolution of organism species and the biosphere during the history of earth. We used thermogravimetry as a primary experimental technique. It allows a simple determi-nation of bound water together with organic and inorganic components in whole soil samples without a special preparation. The primary goal was to search for fingerprinting patterns using dynamics of thermal mass losses (TML) caused by water vaporization from natural soils, as a reference base for soil changes under land use. 301 soil samples were collected in biosphere reserves, national parks and other areas as-sumingly untouched by human activity in Siberia, North and South America, Antarctica, and in several long term agricultural experiments. The results did not support the traditional data evaluation procedures used in classical differ-ential thermogravimetry. For example, peak positions and amplitudes did not provide useful information. In contrast, using thermal mass losses (TML) in prefixed smaller, e.g. 10 °C temperature intervals allowed the determination of the content of carbon, clay, nitrogen and carbonates with high accuracy. However, this approach was applicable for soils and neither for soil-like carbon containing mineral substrates without pedogenetic origin, nor for plant residues or soils containing ashes, cinder, or charcoal. Therefore, intrinsic soil regulation processes are discussed as a possible factor causing

  14. Read/write simulation of thermally stabilized magnetic recording media with a thin film head

    International Nuclear Information System (INIS)

    Takanosu, S.; Abe, T.; Yoneyama, Y.; Fujiwara, N.; Shinagawa, K.

    2004-01-01

    In order to study the thermal stability of an antiferromagnetically coupled medium and a keepered one with a soft magnetic underlayer, a finite element read/write simulation based on the Poisson equation is performed on the 2D model of the medium and a thin film head system. The model used for the recording layer is a Stoner-Wohlfarth model extended at finite temperatures. As a result, it is found that both media have high thermal stability compared with the conventional medium

  15. Electro-optic side-chain polyimide system with large optical nonlinearity and high thermal stability

    Science.gov (United States)

    Sotoyama, Wataru; Tatsuura, Satoshi; Yoshimura, Tetsuzo

    1994-04-01

    We report electro-optic (EO) efficiency and thermal stability of a poled polyimide system with nonlinear optical dyes as side chains. The side-chain polyimide system is synthesized from a dianhydride containing azobenzene dye and a diamine. The dye in the polymer is chemically stable for temperatures below 250 °C. The polymer can be poled simultaneously with or after imidization of the polyamic acid. Our sample poled after imidization shows a large EO coefficient (r33=10.8 pm/V at λ=1.3 μm) and long-term thermal stability at 120 °C.

  16. Cu-based shape memory alloys with enhanced thermal stability and mechanical properties

    International Nuclear Information System (INIS)

    Chung, C.Y.; Lam, C.W.H.

    1999-01-01

    Cu-based shape memory alloys were developed in the 1960s. They show excellent thermoelastic martensitic transformation. However the problems in mechanical properties and thermal instability have inhibited them from becoming promising engineering alloys. A new Cu-Zn-Al-Mn-Zr Cu-based shape memory alloy has been developed. With the addition of Mn and Zr, the martensitic transformation behaviour and the grain size ca be better controlled. The new alloys demonstrates good mechanical properties with ultimate tensile strenght and ductility, being 460 MPa and 9%, respectively. Experimental results revealed that the alloy has better thermal stability, i.e. martensite stabilisation is less serious. In ordinary Cu-Zn-Al alloys, martensite stabilisation usually occurs at room temperature. The new alloy shows better thermal stability even at elevated temperature (∝150 C, >A f =80 C). A limited small amount of martensite stabilisation was observed upon ageing of the direct quenched samples as well as the step quenched samples. This implies that the thermal stability of the new alloy is less dependent on the quenching procedure. Furthermore, such minor martensite stabilisation can be removed by subsequent suitable parent phase ageing. The new alloy is ideal for engineering applications because of its better thermal stability and better mechanical properties. (orig.)

  17. Improved thermal stability of cellulose nanofibrils using low-concentration alkaline pretreatment.

    Science.gov (United States)

    Lee, Hansol; Sundaram, Jaya; Zhu, Lu; Zhao, Yiping; Mani, Sudhagar

    2018-02-01

    The thermal stability of cellulose nanofibrils (CNFs) can be improved by converting cellulose crystalline structure to cellulose II using an alkaline treatment method. The conventional method requires around 20wt.% NaOH solutions and causes the cellulose interdigitation and aggregation, making CNFs production difficult. The objective of this study is to develop a new pretreatment method using a low-concentration alkaline solution to produce well-dispersed CNFs with improved thermal stability. CNFs with 90nm diameter were successfully prepared by treating cellulose powder with 2wt.% NaOH solution below 0°C, followed by homogenization through a French pressure cell press. The CNFs had relatively high thermal stability with the mean onset and maximum thermal decomposition temperature of 305°C and 343°C, respectively, compared with the CNFs prepared without the NaOH pretreatment (283°C and 310°C). The increased thermal stability can create new opportunities for the development of CNF-based bio-composites and electronics. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Thermal conductivity and stability of nano size carbon black filled PDMS: Fuel cell perspective

    CSIR Research Space (South Africa)

    Chen, H

    2011-01-01

    Full Text Available resin-CB composites (with 70wt% loading). Keywords: Polydimethylsiloxane (PDMS); Polymer nanocomposite, Carbon black; Thermal conductivity; Thermal stability; Fuel cell Biographical notes: Hao Chen received his bachelor degree honours in physics... initiative (SANi), his current main research focus is related to smart and engineered nano-materials for photonics and renewable energy applications. Prof. V. Vasudeva Rao holds Bachelors Degree in Mechanical Engineering, Masters Degree...

  19. The analysis of thermal stability of detonation nanodiamond

    Science.gov (United States)

    Efremov, V. P.; Zakatilova, E. I.

    2016-11-01

    The detonation nanodiamond is a new perspective material. Ammunition recycling with use of high explosives and obtaining nanodiamond as the result of the detonation synthesis have given a new motivation for searching of their application areas. In this work nanodiamond powder has been investigated by the method of synchronous thermal analysis. Experiments have been carried out at atmospheric pressure in the environment of argon. Nanodiamond powder has been heated in the closed corundum crucible at the temperature range of 30-1500 °C. The heating rates were varied from 2 K/min to 20 K/min. After the heat treatment, the samples have been studied by the x-ray diffraction and the electron microscopy. As one of the results of this work, it has been found that the detonation nanodiamond has not started the transition into graphite at the temperature below 800 °C.

  20. The analysis of thermal stability of detonation nanodiamond

    International Nuclear Information System (INIS)

    Efremov, V P; Zakatilova, E I

    2016-01-01

    The detonation nanodiamond is a new perspective material. Ammunition recycling with use of high explosives and obtaining nanodiamond as the result of the detonation synthesis have given a new motivation for searching of their application areas. In this work nanodiamond powder has been investigated by the method of synchronous thermal analysis. Experiments have been carried out at atmospheric pressure in the environment of argon. Nanodiamond powder has been heated in the closed corundum crucible at the temperature range of 30-1500 °C. The heating rates were varied from 2 K/min to 20 K/min. After the heat treatment, the samples have been studied by the x-ray diffraction and the electron microscopy. As one of the results of this work, it has been found that the detonation nanodiamond has not started the transition into graphite at the temperature below 800 °C. (paper)

  1. The Influence of Arginine on the Response of Enamel Matrix Derivative (EMD Proteins to Thermal Stress: Towards Improving the Stability of EMD-Based Products.

    Directory of Open Access Journals (Sweden)

    Alessandra Apicella

    Full Text Available In a current procedure for periodontal tissue regeneration, enamel matrix derivative (EMD, which is the active component, is mixed with a propylene glycol alginate (PGA gel carrier and applied directly to the periodontal defect. Exposure of EMD to physiological conditions then causes it to precipitate. However, environmental changes during manufacture and storage may result in modifications to the conformation of the EMD proteins, and eventually premature phase separation of the gel and a loss in therapeutic effectiveness. The present work relates to efforts to improve the stability of EMD-based formulations such as Emdogain™ through the incorporation of arginine, a well-known protein stabilizer, but one that to our knowledge has not so far been considered for this purpose. Representative EMD-buffer solutions with and without arginine were analyzed by 3D-dynamic light scattering, UV-Vis spectroscopy, transmission electron microscopy and Fourier transform infrared spectroscopy at different acidic pH and temperatures, T, in order to simulate the effect of pH variations and thermal stress during manufacture and storage. The results provided evidence that arginine may indeed stabilize EMD against irreversible aggregation with respect to variations in pH and T under these conditions. Moreover, stopped-flow transmittance measurements indicated arginine addition not to suppress precipitation of EMD from either the buffers or the PGA gel carrier when the pH was raised to 7, a fundamental requirement for dental applications.

  2. The Influence of Arginine on the Response of Enamel Matrix Derivative (EMD) Proteins to Thermal Stress: Towards Improving the Stability of EMD-Based Products

    Science.gov (United States)

    Bolisetty, Sreenath; Marascio, Matteo; Gemperli Graf, Anja; Garamszegi, Laszlo; Mezzenga, Raffaele; Fischer, Peter; Månson, Jan-Anders

    2015-01-01

    In a current procedure for periodontal tissue regeneration, enamel matrix derivative (EMD), which is the active component, is mixed with a propylene glycol alginate (PGA) gel carrier and applied directly to the periodontal defect. Exposure of EMD to physiological conditions then causes it to precipitate. However, environmental changes during manufacture and storage may result in modifications to the conformation of the EMD proteins, and eventually premature phase separation of the gel and a loss in therapeutic effectiveness. The present work relates to efforts to improve the stability of EMD-based formulations such as Emdogain™ through the incorporation of arginine, a well-known protein stabilizer, but one that to our knowledge has not so far been considered for this purpose. Representative EMD-buffer solutions with and without arginine were analyzed by 3D-dynamic light scattering, UV-Vis spectroscopy, transmission electron microscopy and Fourier transform infrared spectroscopy at different acidic pH and temperatures, T, in order to simulate the effect of pH variations and thermal stress during manufacture and storage. The results provided evidence that arginine may indeed stabilize EMD against irreversible aggregation with respect to variations in pH and T under these conditions. Moreover, stopped-flow transmittance measurements indicated arginine addition not to suppress precipitation of EMD from either the buffers or the PGA gel carrier when the pH was raised to 7, a fundamental requirement for dental applications. PMID:26670810

  3. Thermal stability of neodymium, samarium, europium and gadolinium thiocarbamide compounds

    International Nuclear Information System (INIS)

    Sakharova, Yu.G.; Borisova, G.M.

    1976-01-01

    The behaviour of thiocarbamide complexes of the composition Me(C 3 H 5 O 2 ) 3 x Cs(NH 2 ) 2 x 3H 2 O, where Me is Nd, Sm, Eu or Gd, has been studied in the process of heating by thermographic, thermogravimetric, and chemical analyses and by infrared spectroscopy. It has been established that thermolysis of complexes is accompanied by thermal effects which point to the fact that the processes take place both with absorption liberation of heat. Above 100 deg C dehydration of compounds begins. The weight of neodymium, samarium, europium, and gadolinium decreases by 11.43, 12.57, 12.57, and 11.48% which corresponds to the loss of water entering into the compounds. It has been proved experimentally that complete removal of water from complexes proceeds at 110 deg C. As main products of thermolysis of thiocarbomide compounds at 230 deg C, oxypropionates of the corresponding rare-earth elements are formed. The highest rate of decomposition of thiocarbamide complexes of rare-earth elements has been attained at 320 and 360 deg C. Qualitative and quantitative analyses as well as IR spectroscopy have shown that the main products of thermolysis at these temperatures are oxysulphates of rare-earth elements with a small impurity of oxysulphides and adsorbed ammonia

  4. Studies on chalcone derivatives: Complex formation, thermal behavior, stability constant and antioxidant activity

    Science.gov (United States)

    El-Sayed, Yusif S.; Gaber, M.

    2015-02-01

    The chalcone 3-[4‧-dimethylaminophenyl]-1-(2-pyridyl) prop-2-en-1-one (DMAPP) and 3-(4‧-diethylaminophenyl)-1-(2-pyridinyl) prop-2-en-1-one abbreviated as DEAPP have been synthesized and characterized with IR, 1H NMR, 13C NMR spectroscopic techniques as described previously (El-Daly et al., 2008; Gaber et al., 2009; El-Sayed, 2013). By using UV visible spectroscopy method the mole fraction ratio for copper with DMAPP and DEAPP complexes were determined and it was found to be 1:1. The stability constants of this complex have been determined by Job's method. The stability constant (Kf) of copper with DMAPP and DEAPP complexes in universal buffer pH = 3.2 was determined to be 9.9 × 104 and 5.2 × 104 respectively. The effect of Cu(II) ion on the emission spectrum of the free chalcone is also assigned. Adherence to Beer's law and Ringbom optimum concentration ranges are determined. The thermal decomposition of the metal complexes is studied by TGA technique. The kinetic parameters like activation energy, pre-exponential factor and entropy of activation are estimated. The structure of complexes was energetically optimized through molecular mechanics applying MM+ force field coupled with molecular dynamics simulation. The bond lengths and bond angles have been calculated to confirm the geometry of the ligands and their Cu(II) complexes. The mode of interaction of the chalcone to copper nanoparticles was studied. The apparent association constants of the colloidal copper nanoparticles:chalcone complexes in solution were evaluated using the spectral method and compared with the formation constant of the Cu(II) chalcone complexes. Antioxidant activity of these chalcones was evaluated by using 1,1‧-diphenyl-2-picrylhydrazyl (DPPHrad) radicals scavenging method, which showed that the antioxidant activity of DMAPP has higher value than the DEAPP. Semi-empirical study results showed that DMAPP have higher dipole moment than DEAPP [1].

  5. High-temperature stability of yttria-stabilized zirconia thermal barrier ...

    Indian Academy of Sciences (India)

    The coatings before and after IR heating were investigated by scanning electron microscopy, X-ray diffraction, electron probe microanalysis, microhardness and residual stress measurements in order to understand the effect of thermal shock on the properties of the TBC. On account of these high-temperature properties, ...

  6. The Effect of Homogenization Heat Treatment on Thermal Expansion Coefficient and Dimensional Stability of Low Thermal Expansion Cast Irons

    Science.gov (United States)

    Chen, Li-Hao; Liu, Zong-Pei; Pan, Yung-Ning

    2016-08-01

    In this paper, the effect of homogenization heat treatment on α value [coefficient of thermal expansion (10-6 K-1)] of low thermal expansion cast irons was studied. In addition, constrained thermal cyclic tests were conducted to evaluate the dimensional stability of the low thermal expansion cast irons with various heat treatment conditions. The results indicate that when the alloys were homogenized at a relatively low temperature, e.g., 1023 K (750 °C), the elimination of Ni segregation was not very effective, but the C concentration in the matrix was moderately reduced. On the other hand, if the alloys were homogenized at a relatively high temperature, e.g., 1473 K (1200 °C), opposite results were obtained. Consequently, not much improvement (reduction) in α value was achieved in both cases. Therefore, a compound homogenization heat treatment procedure was designed, namely 1473 K (1200 °C)/4 hours/FC/1023 K (750 °C)/2 hours/WQ, in which a relatively high homogenization temperature of 1473 K (1200 °C) can effectively eliminate the Ni segregation, and a subsequent holding stage at 1023.15 K (750 °C) can reduce the C content in the matrix. As a result, very low α values of around (1 to 2) × 10-6 K-1 were obtained. Regarding the constrained thermal cyclic testing in 303 K to 473 K (30 °C to 200 °C), the results indicate that regardless of heat treatment condition, low thermal expansion cast irons exhibit exceedingly higher dimensional stability than either the regular ductile cast iron or the 304 stainless steel. Furthermore, positive correlation exists between the α 303.15 K to 473.15 K value and the amount of shape change after the thermal cyclic testing. Among the alloys investigated, Heat I-T3B (1473 K (1200 °C)/4 hours/FC/1023 K (750 °C)/2 hours/WQ) exhibits the lowest α 303 K to 473 K value (1.72 × 10-6 K-1), and hence has the least shape change (7.41 μm) or the best dimensional stability.

  7. Influence of pH, type of acid and recovery media on the thermal inactivation of Listeria innocua.

    Science.gov (United States)

    Miller, Fátima A; Ramos, Bárbara; Gil, Maria M; Brandão, Teresa R S; Teixeira, Paula; Silva, Cristina L M

    2009-07-31

    Acidification of foods with organic acids, either by fermentation or by intentional addition, is an important and common mechanism for controlling foodborne pathogens in a diversity of food products. The objective of this work was to study thermal inactivation of Listeria innocua, an acid tolerant microorganism, at 52.5, 60.0 and 65.0 degrees C, at different pH values (4.5, 6.0 and 7.5), using three types of acid (lactic, acetic and hydrochloric) and three different plating media (Tryptic Soy Agar with 0.6% yeast extract-TSAYE; TSAYE plus 5% NaCl-TSAYE+5%NaCl; and Palcam Agar with selective supplement-Palcam Agar), according to a 3(4) factorial experimental design. Survival data experimentally obtained were fitted with a Gompertz-inspired model and kinetic parameters (shoulder, maximum inactivation rate-k(max), and tail) were estimated for all conditions considered. The influence of temperature, pH, type of acid and enumeration media on kinetic parameters was assessed. Results showed that, with the exception of the type of acid, all the remaining factors and their combinations significantly affected the shoulder period and k(max). In relation to tail, temperature and recovery media were the affectable factors. It was concluded that the survival of this bacteria is higher when combining low temperature with neutral pH, and when TSAYE is the enumeration medium. Bigelow-inspired models were successfully developed and describe accurately the temperature and pH effects on the kinetic parameters.

  8. Adhesion properties and stability to thermal oxidation of irradiated copolymers of ethylene with vinyl acetate

    International Nuclear Information System (INIS)

    Ovechkina, G.I.; Soboleva, N.S.; Naumkina, S.I.; Ovechkin, P.L.; Leshchenko, S.S.; Finkel', Eh.Eh.; Karpov, V.L.

    1981-01-01

    Effect of gamma radiation on adhesion strength and stability to thermal oxidation of copolymers of ethylene with vinyl acetate of different composition is considered. Polyetiylene, PVC-plasticized substance copper are used as substrates. Optimum radiation doses for copolymers of different composition are determined [ru

  9. Polyesteramides based on PET and nylon 2,T part 2. synthesis and thermal stability

    NARCIS (Netherlands)

    Bouma, K.; Groot, G.M.M.; Feijen, Jan; Gaymans, R.J.

    2000-01-01

    The synthesis and the thermal stability of polyesteramides based on PET and nylon 2,T (PETA) using DMT, T2T-dimethyl (N,N′-bis(p-carbo-methoxybenzoyl)ethanediamine) and 1,2-ethanediol as starting materials has been studied. The catalysts that were used are tetraisopropyl orthotitanate, manganese

  10. Thermal stability of catalytically grown multi-walled carbon nanotubes observed in transmission electron microscopy

    DEFF Research Database (Denmark)

    Wang, Cheng-Yu; Liu, Chuan-Pu; Boothroyd, Chris

    2009-01-01

    The thermal stability of multi-walled carbon nanotubes (MWCNTs) was assessed in situ by transmission electron microscopy. Upon heating, Ni catalysts in MWC-NTs containing bamboo structures shrank from the tail due to evaporation, leading to additional bamboo formation and tube elongation at 800...

  11. Enhanced thermal stability of the thylakoid membranes from spruce. A comparison with selected angiosperms

    Czech Academy of Sciences Publication Activity Database

    Karlický, Václav; Kurasová, Irena; Ptáčková, B.; Večeřová, Kristýna; Urban, Otmar; Špunda, Vladimír

    2016-01-01

    Roč. 130, 1-3 (2016), s. 357-371 ISSN 0166-8595 R&D Projects: GA MŠk(CZ) LO1415; GA ČR GA13-28093S Institutional support: RVO:67179843 Keywords : Norway spruce * Thermal stability * Circular dichroism * Photosystem II organization * Thylakoid membrane Subject RIV: ED - Physiology Impact factor: 3.864, year: 2016

  12. Adsorption behavior of perfluorinated sulfonic acid ionomer on highly graphitized carbon nanofibers and their thermal stabilities

    DEFF Research Database (Denmark)

    Andersen, Shuang Ma; Borghei, Maryam; Dhiman, Rajnish

    2014-01-01

    of decreasing hydrophobicity. This is indicated by the initial decrease and then increase in the value of Keq. with the increasing strength of the acid treatment. The corresponding carbon - ionomer composite also showed varying thermal stability depending on Nafion orientation. The specific maximum surface...

  13. Respective importance of protein folding and glycosylation in the thermal stability of recombinant feruloyl esterase A

    NARCIS (Netherlands)

    Benoit, Isabelle; Asther, Michèle; Sulzenbacher, Gerlind; Record, Eric; Marmuse, Laurence; Parsiegla, Goetz; Gimbert, Isabelle; Asther, Marcel; Bignon, Christophe

    2006-01-01

    The thermal stability of four molecular forms (native, refolded, glycosylated, non-glycosylated) of feruloyl esterase A (FAEA) was studied. From the most to the least thermo-resistant, the four molecular species ranked as follows: (i) glycosylated form produced native, (ii) non-glycosylated form

  14. Why collagens best survived in fossils? Clues from amino acid thermal stability

    DEFF Research Database (Denmark)

    Wang, Shuang-Yin; Cappellini, Enrico; Zhang, Hong-Yu

    2012-01-01

    Explaining why type I collagens are preferentially preserved in the geological time scale remains a challenge. Several pieces of evidence indicate that its rich content in the bone and its unique, stable structure played key roles in its preservation. By considering the distinct thermal stability...

  15. Study of thermal stability of ultrafine-grained copper by means of electron back scattering diffraction

    Czech Academy of Sciences Publication Activity Database

    Man, O.; Pantělejev, L.; Kunz, Ludvík

    2010-01-01

    Roč. 51, č. 2 (2010), s. 209-213 ISSN 1345-9678 R&D Projects: GA AV ČR 1QS200410502 Institutional research plan: CEZ:AV0Z20410507 Keywords : ultra-fine grained copper * thermal stability of microstructure * electron back scattering diffraction * grain size * texture Subject RIV: JG - Metallurgy Impact factor: 0.779, year: 2010

  16. Pickering emulsions stabilized by whey protein nanoparticles prepared by thermal cross-linking

    NARCIS (Netherlands)

    Wu, Jiande; Shi, Mengxuan; Li, Wei; Zhao, Luhai; Wang, Ze; Yan, Xinzhong; Norde, Willem; Li, Yuan

    2015-01-01

    A Pickering (o/w) emulsion was formed and stabilized by whey protein isolate nanoparticles (WPI NPs). Those WPI NPs were prepared by thermal cross-linking of denatured WPI proteins within w/o emulsion droplets at 80. °C for 15. min. During heating of w/o emulsions containing 10% (w/v) WPI

  17. Testing of High Thermal Cycling Stability of Low Strength Concrete as a Thermal Energy Storage Material

    Directory of Open Access Journals (Sweden)

    Chao Wu

    2016-09-01

    Full Text Available Concrete has the potential to become a solution for thermal energy storage (TES integrated in concentrating solar power (CSP systems due to its good thermal and mechanical properties and low cost of material. In this study, a low strength concrete (C20 is tested at high temperatures up to 600 °C. Specimens are thermally cycled at temperatures in the range of 400–300 °C, 500–300 °C, and 600–300 °C, which TES can reach in operation. For comparison, specimens also cycled at temperature in the range of 400–25 °C (room temperature, 500–25 °C, and 600–25 °C. It is found from the test results that cracks are not observed on the surfaces of concrete specimens until the temperature is elevated up to 500 °C. There is mechanical deterioration of concrete after exposure to high temperature, especially to high thermal cycles. The residual compressive strength of concrete after 10 thermal cycles between 600 °C and 300 °C is about 58.3%, but the specimens remain stable without spalling, indicating possible use of low strength concrete as a TES material.

  18. Co-evaporation of fluoropolymer additives for improved thermal stability of organic semiconductors

    Science.gov (United States)

    Price, Jared S.; Wang, Baomin; Grede, Alex J.; Shen, Yufei; Giebink, Noel C.

    2017-08-01

    Reliability remains an ongoing challenge for organic light emitting diodes (OLEDs) as they expand in the marketplace. The ability to withstand operation and storage at elevated temperature is particularly important in this context, not only because of the inverse dependence of OLED lifetime on temperature, but also because high thermal stability is fundamentally important for high power/brightness operation as well as applications such as automotive lighting, where interior car temperatures often exceed the ambient by 50 °C or more. Here, we present a strategy to significantly increase the thermal stability of small molecule OLEDs by co-depositing an amorphous fluoropolymer, Teflon AF, to prevent catastrophic failure at elevated temperatures. Using this approach, we demonstrate that the thermal breakdown limit of common hole transport materials can be increased from typical temperatures of ˜100 °C to more than 200 °C while simultaneously improving their electrical transport properties. Similar thermal stability enhancements are demonstrated in simple bilayer OLEDs. These results point toward a general approach to engineer morphologically-stable organic electronic devices that are capable of operating or being stored in extreme thermal environments.

  19. Network structure and thermal stability study of high temperature seal glass

    Science.gov (United States)

    Lu, K.; Mahapatra, M. K.

    2008-10-01

    High temperature seal glass has stringent requirement on glass thermal stability, which is dictated by glass network structures. In this study, a SrO-La2O3-Al2O3-B2O3-SiO2 based glass system was studied using nuclear magnetic resonance, Raman spectroscopy, and x-ray diffraction for solid oxide cell application purpose. Glass structural unit neighboring environment and local ordering were evaluated. Glass network connectivity as well as silicon and boron glass former coordination were calculated for different B2O3:SiO2 ratios. Thermal stability of the borosilicate glasses was studied after thermal treatment at 850 °C. The study shows that high B2O3 content induces BO4 and SiO4 structural unit ordering, increases glass localized inhomogeneity, decreases glass network connectivity, and causes devitrification. Glass modifiers interact with either silicon- or boron-containing structural units and form different devitrified phases at different B2O3:SiO2 ratios. B2O3-free glass shows the best thermal stability among the studied compositions, remaining stable after thermal treatment for 200 h at 850 °C.

  20. Study on thermal stability and chemical structure of polyamide blended with small amount of Cu

    International Nuclear Information System (INIS)

    Arai, Tsuyoshi; Ueno, Tomonaga; Kajiya, Takafumi; Ishikawa, Tomoyuki; Takeda, Kunihiko

    2007-01-01

    The thermal stability and the chemical structure of Polyamide 66 (PA66) blended with a small amount of copper have been studied. The thermal degradation of the blend with 35 ppm or more of copper was restrained and no strong influence of the concentration of copper was observed. The molecular weight of PA66 decreased by the thermal aging process but the amount of decrease of the blend was smaller than that of the non-blend. The water uptake of the blend increased. The chemical structure, which was observed by IR and NMR, changed slightly by blending with copper after aging at higher temperatures. Multiple items influenced the thermal stability of PA66 blended with a small amount of copper instead of just one. Namely, the main chain of PA66 is cut by heat and the degree of the cut is restrained by the copper. The diffusion time of copper atoms that disperse uniformly in the PA66 matrix is short enough to cover the individual amide groups and the effect enlarges the entire configuration of the PA66 chain to enhance the thermal stability. (author)

  1. Maximum conversion of heavy hydrocarbons. Product stability dictates thermal and catalytic conversion rates of residues

    Energy Technology Data Exchange (ETDEWEB)

    Hennico, A.; Peries, J.P. (Institut Francais du Petrole, 92 - Rueil Malmaison (France)); Laurent, J.; Espeillac, M.

    1992-01-01

    The maximum conversion achieved by thermal cracking is limited by the fuel stability. The same holds for catalytic hydrotreating. ASVAHL has studied for many years the relation between conversion and product stability in thermal and catalytic processes. Thermal Mode: Several solutions are proposed to increase the conversion of the TERVAHL T visbreaking process such as the use of hydrogen (TERVAHL H) and possibly the addition of a few ppm of a dispersed catalyst (TERVAHL C). Catalytic Mode: The conversion of the HYVAHL residue hydrotreating process may be increased either by adding a hydrovisbreaking furnace before the hydrotreating step (HYVAHL T) or by adding an existing visbreaking downstream the hydrotreating step. These various routes enable the ASVAHL processes to maximize the marketable light product quantities in function of the residue to be upgraded and the fuel qualities to be assured. (orig.).

  2. Thermal Stability and Rheological Behaviors of High-Density Polyethylene/Fullerene Nanocomposites

    Directory of Open Access Journals (Sweden)

    Liping Zhao

    2012-01-01

    Full Text Available High-density polyethylene/fullerene (HDPE/C60 nanocomposites with the C60 loading that varied from 0.5 to 5.0% by weight were prepared via melt compounding. Thermogravimetric analysis (TGA and differential scanning calorimetry (DSC results showed that the presence of C60 could remarkably enhance the thermal properties of HDPE. A very low C60 loading (0.5 wt% increased the onset degradation temperature from 389∘C to 459∘C and decreased the heat release from 3176 J/g to 1490 J/g. The larger the loading level of C60, the better the thermal stability of HDPE/C60 nanocomposites. Rheological investigation results showed that the free radical trapping effect of C60 was responsible for the improved thermal stability of HDPE.

  3. Degradation mechanism and thermal stability of urea nitrate below the melting point

    International Nuclear Information System (INIS)

    Desilets, Sylvain; Brousseau, Patrick; Chamberland, Daniel; Singh, Shanti; Feng, Hongtu; Turcotte, Richard; Anderson, John

    2011-01-01

    Highlights: → Decomposition mechanism of urea nitrate. → Spectral characterization of the decomposition mechanism. → Thermal stability of urea nitrate at 50, 70 and 100 o C. → Chemical balance of decomposed products released. - Abstract: Aging and degradation of urea nitrate below the melting point, at 100 o C, was studied by using thermal analysis and spectroscopic methods including IR, Raman, 1 H and 13 C NMR techniques. It was found that urea nitrate was completely degraded after 72 h at 100 o C into a mixture of solids (69%) and released gaseous species (31%). The degradation mechanism below the melting point was clearly identified. The remaining solid mixture was composed of ammonium nitrate, urea and biuret while unreacted residual nitric and isocyanic acids as well as traces of ammonia were released as gaseous species at 100 o C. The thermal stability of urea nitrate, under extreme storage conditions (50 o C), was also examined by isothermal nano-calorimetry.

  4. Improved thermal stability and wettability behavior of thermoplastic polyurethane / barium metaborate composites

    Energy Technology Data Exchange (ETDEWEB)

    Baştürka, Emre; Madakbaş, Seyfullah; Kahraman, Memet Vezir, E-mail: smadakbas@marmara.edu.tr [Department of Chemistry, Marmara University, Istanbul (Turkey)

    2016-03-15

    In this paper, it was targeted to the enhance thermal stability and wettability behavior of thermoplastic polyurethane (TPU) by adding barium metaborate. TPU-Barium metaborate composites were prepared by adding various proportions of barium metaborate to TPU. The chemical structures of the composites were characterised by fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) analysis. All prepared composites have extremely high Tg and thermal stability as determined from DSC and TGA analysis. All composite materials have the Tg ranging from 15 to 35 °C. The surface morphologies of the composites were investigated by a scanning electron microscopy. Mechanical properties of the samples were characterized with stress-strain test. Hydrophobicity of the samples was determined by the contact angle measurements. The obtained results proved that thermal, hydrophobic and mechanical properties were improved. (author)

  5. Synthesis, characterization and thermal stability of solid solutions Zr (Y, Fe, MoO2

    Directory of Open Access Journals (Sweden)

    Felipe Legorreta-García

    2015-05-01

    Full Text Available The synthesis of Fe3+, Mo4+ and Y3+ fully stabilized zirconia by the nitrate/urea combustion route and thermal stability in air was investigated. The solid solution obtained was characterized by X ray diffraction (XRD, scanning electron microscopy (SEM and used the BET method for determining specific surface. The ceramic powders obtained were calcined at 1473 K in air atmosphere in order to determine their thermal stability. The scanning electron microscopy (SEM results showed a homogeneous grain surface, measuring several tens of micrometers across. The crystallographic study revealed that by this method it was successfully achieved zirconia doped with Fe3+, Mo4+ and Y3+ ions in the zirconia tetragonal monophase, even after calcinations.

  6. Synthesis, characterization and thermal stability of solid solutions Zr (Y, Fe, Mo)O {sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Legorreta-Garcia, F.; Esperanza Hernandez-Cruz, L.; Villanueva-Ibanez, M.; Flores-Gonzalez, M. A.

    2015-10-01

    The synthesis of Fe{sup 3}+, Mo{sup 4+} and Y{sup 3+} fully stabilized zirconia by the nitrate/urea combustion route and thermal stability in air was investigated. The solid solution obtained was characterized by X ray diffraction (XRD), scanning electron microscopy (SEM) and used the BET method for determining specific surface. The ceramic powders obtained were calcined at 1473 K in air atmosphere in order to determine their thermal stability. The scanning electron microscopy (SEM) results showed a homogeneous grain surface, measuring several tens of micrometers across. The crystallographic study revealed that by this method it was successfully achieved zirconia doped with Fe{sup 3+}, Mo{sup 4+} and Y{sup 3+} ions in the zirconia tetragonal monophase, even after calcinations. (Author)

  7. Effect of electrolyte valency, alginate concentration and pH on engineered TiO₂ nanoparticle stability in aqueous solution.

    Science.gov (United States)

    Loosli, Frédéric; Le Coustumer, Philippe; Stoll, Serge

    2015-12-01

    Agglomeration and disagglomeration processes are expected to play a key role on the fate of engineered nanoparticles in natural aquatic systems. These processes are investigated here in detail by studying first the stability of TiO2 nanoparticles in the presence of monovalent and divalent electrolytes at different pHs (below and above the point of zero charge of TiO2) and discussing the importance of specific divalent cation adsorption with the help of the DLVO theory as well as the importance of the nature of the counterions. Then the impact of one polysaccharide (alginate) on the stability of agglomerates formed under pH and water hardness representative of Lake Geneva environmental conditions is investigated. In these conditions the large TiO2 agglomerates (diameter>1μm) are positively charged due to Ca(2+) and Mg(2+) specific adsorption and alginate, which is negatively charged, adsorbs onto the agglomerate surface. Our results indicate that the presence of alginate at typical natural organic matter concentration (1-10 mg L(-1)) strongly modifies the TiO2 agglomerate (50 mg L(-1)) stability by inducing their partial and rapid disagglomeration. The importance of disagglomeration is found dependent on the alginate concentration with maximum of disagglomeration obtained for alginate concentration ≥8 mg L(-1) and leading to 400 nm fragments. From an environmental point of view partial restabilization of TiO2 agglomerates in the presence of alginate constitutes an important outcome. Disagglomeration will enhance their transport and residence time in aquatic systems which is an important step in the current knowledge on risk assessment associated to engineered nanoparticles. Copyright © 2015 Elsevier B.V. All rights reserved.

  8. Extreme temperature stability of thermally insulating graphene-mesoporous-silicon nanocomposite

    Science.gov (United States)

    Kolhatkar, Gitanjali; Boucherif, Abderraouf; Rahim Boucherif, Abderrahim; Dupuy, Arthur; Fréchette, Luc G.; Arès, Richard; Ruediger, Andreas

    2018-04-01

    We demonstrate the thermal stability and thermal insulation of graphene-mesoporous-silicon nanocomposites (GPSNC). By comparing the morphology of GPSNC carbonized at 650 °C as-formed to that after annealing, we show that this nanocomposite remains stable at temperatures as high as 1050 °C due to the presence of a few monolayers of graphene coating on the pore walls. This does not only make this material compatible with most thermal processes but also suggests applications in harsh high temperature environments. The thermal conductivity of GPSNCs carbonized at temperatures in the 500 °C-800 °C range is determined through Raman spectroscopy measurements. They indicate that the thermal conductivity of the composite is lower than that of silicon, with a value of 13 ± 1 W mK-1 at room temperature, and not affected by the thin graphene layer, suggesting a role of the high concentration of carbon related-defects as indicated by the high intensity of the D-band compared to G-band of the Raman spectra. This morphological stability at high temperature combined with a high thermal insulation make GPSNC a promising candidate for a broad range of applications including microelectromechanical systems and thermal effect microsystems such as flow sensors or IR detectors. Finally, at 120 °C, the thermal conductivity remains equal to that at room temperature, attesting to the potential of using our nanocomposite in devices that operate at high temperatures such as microreactors for distributed chemical conversion, solid oxide fuel cells, thermoelectric devices or thermal micromotors.

  9. Microstructure and thermal stability of Fe, Ti and Ag implanted Yttria-stabilized zirconia

    NARCIS (Netherlands)

    van Hassel, B.A.; van Hassel, B.A.; Burggraaf, Anthonie; Burggraaf, A.J.

    1991-01-01

    Yttria-stabilized zirconia (YSZ) was implanted with 15 keV Fe or Ti ions up to a dose of 8×1016 at cm−2. The resulting “dopant” concentrations exceeded the concentrations corresponding to the equilibrium solid solubility of Fe2O3 or TiO2 in YSZ. During oxidation in air at 400° C, the Fe and Ti

  10. Comparison of Thermal Stability of Dry High-strength Concrete and Wet High-strength Concrete

    Directory of Open Access Journals (Sweden)

    Musorina Tatiana

    2018-01-01

    Full Text Available High-strength concrete is a modern material, which occupies it`s own niche on the construction material market. It is applicable in a large-scale high-rise construction, particularly an underground construction is a frequently used solution for a space saving. Usually underground structure is related to a wet usage environment. Though not all properties of the high-strength concrete are investigated to the full extent. Under adverse climatic conditions of the Russian Federation one of the most important properties for constructional materials is a thermal capacity. Therefore, the main purpose of the paper is to compare a thermal capacity of the high-strength concrete in humid conditions and a thermal capacity of the high-strength concrete in dry operational condition. During the study dependency between thermal capacity and design wall thickness and ambient humidity has to be proven with two experiments. As a result the theoretical relation between thermal capacity characteristic – thermal inertia and wall thickness and ambient humidity was confirmed by the experimental data. The thermal capacity of a building is in direct ratio to the construction thickness. It follows from the experiments and calculations that wet high-strength concrete has less thermal stability.

  11. Comparison of Thermal Stability of Dry High-strength Concrete and Wet High-strength Concrete

    Science.gov (United States)

    Musorina, Tatiana; Katcay, Aleksandr; Selezneva, Anna; Kamskov, Victor

    2018-03-01

    High-strength concrete is a modern material, which occupies it`s own niche on the construction material market. It is applicable in a large-scale high-rise construction, particularly an underground construction is a frequently used solution for a space saving. Usually underground structure is related to a wet usage environment. Though not all properties of the high-strength concrete are investigated to the full extent. Under adverse climatic conditions of the Russian Federation one of the most important properties for constructional materials is a thermal capacity. Therefore, the main purpose of the paper is to compare a thermal capacity of the high-strength concrete in humid conditions and a thermal capacity of the high-strength concrete in dry operational condition. During the study dependency between thermal capacity and design wall thickness and ambient humidity has to be proven with two experiments. As a result the theoretical relation between thermal capacity characteristic - thermal inertia and wall thickness and ambient humidity was confirmed by the experimental data. The thermal capacity of a building is in direct ratio to the construction thickness. It follows from the experiments and calculations that wet high-strength concrete has less thermal stability.

  12. Thermal stabilization of dihydrofolate reductase using monte carlo unfolding simulations and its functional consequences.

    Directory of Open Access Journals (Sweden)

    Jian Tian

    2015-04-01

    Full Text Available Design of proteins with desired thermal properties is important for scientific and biotechnological applications. Here we developed a theoretical approach to predict the effect of mutations on protein stability from non-equilibrium unfolding simulations. We establish a relative measure based on apparent simulated melting temperatures that is independent of simulation length and, under certain assumptions, proportional to equilibrium stability, and we justify this theoretical development with extensive simulations and experimental data. Using our new method based on all-atom Monte-Carlo unfolding simulations, we carried out a saturating mutagenesis of Dihydrofolate Reductase (DHFR, a key target of antibiotics and chemotherapeutic drugs. The method predicted more than 500 stabilizing mutations, several of which were selected for detailed computational and experimental analysis. We find a highly significant correlation of r=0.65-0.68 between predicted and experimentally determined melting temperatures and unfolding denaturant concentrations for WT DHFR and 42 mutants. The correlation between energy of the native state and experimental denaturation temperature was much weaker, indicating the important role of entropy in protein stability. The most stabilizing point mutation was D27F, which is located in the active site of the protein, rendering it inactive. However for the rest of mutations outside of the active site we observed a weak yet statistically significant positive correlation between thermal stability and catalytic activity indicating the lack of a stability-activity tradeoff for DHFR. By combining stabilizing mutations predicted by our method, we created a highly stable catalytically active E. coli DHFR mutant with measured denaturation temperature 7.2°C higher than WT. Prediction results for DHFR and several other proteins indicate that computational approaches based on unfolding simulations are useful as a general technique to discover

  13. Examination of lignocellulosic fibers for chemical, thermal, and separations properties: Addressing thermo-chemical stability issues

    Science.gov (United States)

    Johnson, Carter David

    Natural fiber-plastic composites incorporate thermoplastic resins with fibrous plant-based materials, sometimes referred to as biomass. Pine wood mill waste has been the traditional source of natural fibrous feedstock. In anticipation of a waste wood shortage other fibrous biomass materials are being investigated as potential supplements or replacements. Perennial grasses, agricultural wastes, and woody biomass are among the potential source materials. As these feedstocks share the basic chemical building blocks; cellulose, hemicellulose, and lignin, they are collectively called lignocellulosics. Initial investigation of a number of lignocellulosic materials, applied to fiber-plastic composite processing and material testing, resulted in varied results, particularly response to processing conditions. Less thermally stable lignocellulosic filler materials were physically changed in observable ways: darkened color and odor. The effect of biomass materials' chemical composition on thermal stability was investigated an experiment involving determination of the chemical composition of seven lignocellulosics: corn hull, corn stover, fescue, pine, soy hull, soy stover, and switchgrass. These materials were also evaluated for thermal stability by thermogravimetric analysis. The results of these determinations indicated that both chemical composition and pretreatment of lignocellulosic materials can have an effect on their thermal stability. A second study was performed to investigate what effect different pretreatment systems have on hybrid poplar, pine, and switchgrass. These materials were treated with hot water, ethanol, and a 2:1 benzene/ethanol mixture for extraction times of: 1, 3, 6, 12, and 24 hours. This factorial experiment demonstrated that both extraction time and medium have an effect on the weight percent of extractives removed from all three material types. The extracted materials generated in the above study were then subjected to an evaluation of thermal

  14. Data on blueberry peroxidase kinetic characterization and stability towards thermal and high pressure processing

    Directory of Open Access Journals (Sweden)

    Netsanet Shiferaw Terefe

    2017-08-01

    Full Text Available The data presented in this article are related to a research article entitled ‘Thermal and high pressure inactivation kinetics of blueberry peroxidase’ (Terefe et al., 2017 [1]. In this article, we report original data on the activity of partially purified blueberry peroxidase at different concentrations of hydrogen peroxide and phenlylenediamine as substrates and the effects of thermal and high pressure processing on the activity of the enzyme. Data on the stability of the enzyme during thermal (at temperatures ranging from 40 to 80 °C and combined thermal-high pressure processing (100–690 MPa, 30–90 °C are included in this report. The data are presented in this format in order to facilitate comparison with data from other researchers and allow statistical analyses and modeling by others in the field.

  15. Synthesis and characterization of conducting composites of polyaniline and carbon black with high thermal stability

    Directory of Open Access Journals (Sweden)

    Fabio R. Simões

    2009-01-01

    Full Text Available In this work, a detailed chemical route to prepare thermally stable polyaniline (PANI/carbon black (CB composites is described. The syntheses were performed by chemical polymerization of aniline over CB particles, using different PANI/CB mass ratios. The thermal and electrical properties were characterized. Composites with mass ratio up to 65:35 (PANI:CB showed excellent thermal stability maintaining their conducting properties when thermally treated at 230 °C for two hours, which is adequate to process these materials. Moreover, the results showed an important reduction in the surface area of the composites which have a good relationship with the improvement of the rheological properties in melt processing.

  16. Thermal Stability of Hexamethyldisiloxane (MM for High-Temperature Organic Rankine Cycle (ORC

    Directory of Open Access Journals (Sweden)

    Markus Preißinger

    2016-03-01

    Full Text Available The design of efficient Organic Rankine Cycle (ORC units for the usage of industrial waste heat at high temperatures requires direct contact evaporators without intermediate thermal oil circuits. Therefore, the thermal stability of high-temperature working fluids gains importance. In this study, the thermal degradation of hexamethyldisiloxane (MM is investigated in an electrically heated tube. Qualitative results concerning remarks on degradation products as well as quantitative results like the annual degradation rate are presented. It is shown that MM is stable up to a temperature of 300 °C with annual degradation rates of less than 3.5%. Furthermore, the break of a silicon–carbon bond can be a main chemical reaction that influences the thermal degradation. Finally, it is discussed how the results may impact the future design of ORC units.

  17. The thermal and storage stability of bovine haemoglobin by ultraviolet-visible and circular dichroism spectroscopies.

    Science.gov (United States)

    Bhomia, Ruchir; Trivedi, Vivek; Coleman, Nichola J; Mitchell, John C

    2016-08-01

    The effects of temperature, pH and long-term storage on the secondary structure and conformation changes of bovine haemoglobin (bHb) were studied using circular dichroism (CD) and ultraviolet--visible (UV-vis) spectroscopies. Neural network software was used to deconvolute the CD data to obtain the fractional content of the five secondary structures. The storage stability of bHb solutions in pH 6, 7 and 8 buffers was significantly higher at 4 °C than at 23 °C for the first 3 days. A complete denaturation of bHb was observed after 40 days irrespective of storage temperature or pH. The bHb solutions were also exposed to heating and cooling cycles between 25 and 65 °C and structural changes were followed by UV-vis and CD spectroscopies. These experiments demonstrated that α-helix content of bHb decreased steadily with the increasing temperature above 35 °C at all pH values. The loss in α-helicity and gain in random coil conformations was pH-dependent and the greatest under alkaline conditions. Furthermore, there was minimal recovery of the secondary structure content upon cooling to 25 °C. The use of bHb as a model drug is very common and this study elucidates the significance of storage and processing conditions on its stability.

  18. Selective aminolysis of acetylated lignin: Toward simultaneously improving thermal-oxidative stability and maintaining mechanical properties of polypropylene.

    Science.gov (United States)

    Ye, Dezhan; Kong, Jinfeng; Gu, Shaojin; Zhou, Yingshan; Huang, Caoxing; Xu, Weilin; Zhang, Xi

    2018-03-01

    Even with outstanding radical capturing ability, the utilization of lignin as a natural antioxidant in polypropylene (PP) still has been pended. Usually, the compatibility of its blends is improved based on the reaction of hydroxyl content, thus leading to the decreasing content of phenolic hydroxyl (Ph-OH) group and inferior thermal-oxidative stability of lignin blends. Here, the selective aminolysis of acetylated Kraft lignin (pyr-KL) was investigated, which structures were characterized using FTIR, 31 P-NMR and GPC. The Ph-OH group of acetylated KL could be released by the addition of pyrrolidine; however the aliphatic hydroxyl group is still blocked. With the control of reaction conditions, the highest oxidation induction time of pyr-KL/PP (0.5wt% loading) reaches up to 22.6min, almost 2.6 times than that of pure PP. More importantly, the mechanical properties of PP were also maintained under the loading of pyr-KL, which is much better than that of curde KL/PP. Copyright © 2017 Elsevier B.V. All rights reserved.

  19. Size-dependent thermal stability analysis of graded piezomagnetic nanoplates on elastic medium subjected to various thermal environments

    Science.gov (United States)

    Ebrahimi, Farzad; Barati, Mohammad Reza

    2016-10-01

    This paper investigates the thermal stability of magneto-electro-thermo-elastic functionally graded (METE-FG) nanoplates based on the nonlocal theory and a refined plate model. The METE-FG nanoplate is subjected to the external electric potential, magnetic potential and different temperature rises. Interaction of elastic medium with the METE-FG nanoplate is modeled via Winkler-Pasternak foundation model. The governing equations are derived by using the Hamilton principle and solved by using an analytical method to determine the critical buckling temperatures. To verify the validity of the developed model, the results of the present work are compared with those available in the literature. A detailed parametric study is conducted to study the influences of the nonlocal parameter, foundation parameters, temperature rise, external electric and magnetic potentials on the size-dependent thermal buckling characteristics of METE-FG nanoplates.

  20. Enhanced thermal stability of RuO2/polyimide interface for flexible device applications

    Science.gov (United States)

    Music, Denis; Schmidt, Paul; Chang, Keke

    2017-09-01

    We have studied the thermal stability of RuO2/polyimide (Kapton) interface using experimental and theoretical methods. Based on calorimetric and spectroscopic analyses, this inorganic-organic system does not exhibit any enthalpic peaks as well as all bonds in RuO2 and Kapton are preserved up to 500 °C. In addition, large-scale density functional theory based molecular dynamics, carried out in the same temperature range, validates the electronic structure and points out that numerous Ru-C and a few Ru-O covalent/ionic bonds form across the RuO2/Kapton interface. This indicates strong adhesion, but there is no evidence of Kapton degradation upon thermal excitation. Furthermore, RuO2 does not exhibit any interfacial bonds with N and H in Kapton, providing additional evidence for the thermal stability notion. It is suggested that the RuO2/Kapton interface is stable due to aromatic architecture of Kapton. This enhanced thermal stability renders Kapton an appropriate polymeric substrate for RuO2 containing systems in various applications, especially for flexible microelectronic and energy devices.

  1. A thermal stability study of alkane and aromatic thiolate self-assembled monolayers on copper surfaces

    Science.gov (United States)

    Carbonell, L.; Whelan, C. M.; Kinsella, M.; Maex, K.

    2004-07-01

    The thermal stability of 1-decanethiol (C10) and benzenethiol (BT) Self-Assembled Monolayers (SAMs) on metallic and oxidized copper surfaces has been investigated by thermal desorption spectrometry. High quality C10 and BT SAMs exhibit low thermal stabilities on clean copper surfaces with a maximum in decomposition occurring between 100 and 150 ∘C. The decomposition of SAMs follows different mechanisms. For the alkanethiol, a direct interaction between the alkyl group of the thiolate and the metallic copper surface is the dominant pathway for the C-S bond scission. The head group desorbs as oxidized sulfur and this is followed by the desorption of the alkyl fragments of the chain adsorbed on the clean copper surface. In the case of benzenethiol, a simultaneous desorption of the head group as oxidized sulfur and the benzene group occurs. SAM formation on the oxidized copper surface results in complete removal and/or reduction of the CuO layer. Higher SAM surface coverages on the resulting Cu/Cu 2O surface result from the enhanced surface roughness of the substrate. The decomposition mechanisms and thermal stabilities of the C10 and BT SAMs are dependent on the oxidation state of the underlying substrate and the chemical nature of the chain.

  2. Thermal stability of corn oil flavoured with Thymus capitatus under heating and deep-frying conditions.

    Science.gov (United States)

    Karoui, Iness Jabri; Dhifi, Wissal; Jemia, Meriam Ben; Marzouk, Brahim

    2011-03-30

    The thermal stability of corn oil flavoured with thyme flowers was determined and compared with that of the original refined corn oil (control). The oxidative stability index (OSI) was measured and samples were exposed to heating (30 min at 150, 180 and 200 °C) and deep-frying (180 °C). Changes in peroxide value (PV), free fatty acid (FFA) content, specific absorptivity values (K(232) and K(270)), colour and chlorophyll, carotenoid and total phenol contents were monitored. The OSI and heating results showed that thyme incorporation was effective against thermal oxidation based on the increased induction time observed for the flavoured oil (6.48 vs 4.36 h), which was characterised by lower PV, FFA content, K(232) and K(270) than the control oil after heating from 25 to 200 °C, with higher red and yellow colour intensities and chlorophyll, carotenoid and total phenol contents. The deep-frying test showed the accelerated deterioration of both oils in the presence of French fries. Compared with the control oil, the thyme-flavoured oil showed improved thermal stability after heating. This could be attributed to the presence of thyme pigments and antioxidant compounds allowing extended oil thermal resistance. Copyright © 2011 Society of Chemical Industry.

  3. Thermal Stability Results of a Fischer-Tropsch Fuel With Various Blends of Aromatic Solution

    Science.gov (United States)

    Lindsey, Jennifer; Klettlinger, Suder

    2013-01-01

    Fischer-Tropsch (F-T) jet fuel composition differs from petroleum-based, conventional commercial jet fuel because of differences in feedstock and production methodology. F-T fuel typically has a lower aromatic and sulfur content and consists primarily of iso and normal paraffins. The ASTM D3241 specification for Jet Fuel Thermal Oxidation Test (JFTOT) break point testing method was used to test the breakpoint of a baseline commercial grade F-T jet fuel, and various blends of this F-T fuel with an aromatic solution. The goal of this research is to determine the effect of aromatic content on the thermal stability of F-T fuel. The testing completed in this report was supported by the NASA Fundamental Aeronautics Subsonic Fixed Wing Project. Two different aromatic content fuels from Rentech, as well as these fuels with added aromatic blend were analyzed for thermal stability using the JFTOT method. Preliminary results indicate a reduction in thermal stability occurs upon increasing the aromatic content to 10% by adding an aromatic blend to the neat fuel. These results do not specify a failure based on pressure drop, but only on tube color. It is unclear whether tube color correlates to more deposition on the tube surface or not. Further research is necessary in order to determine if these failures are true failures based on tube color. Research using ellipsometry to determine tube deposit thickness rather than color will be continued in follow-up of this study.

  4. Thermal stability and conformational changes of transglutaminase from a newly isolated Streptomyces hygroscopicus.

    Science.gov (United States)

    Cui, Li; Du, Guocheng; Zhang, Dongxu; Chen, Jian

    2008-06-01

    Thermal stability and conformational changes of transglutaminase (TGase) from a newly isolated Streptomyces hygroscopicus were investigated in this study. The inactivation kinetics of the microbial transglutaminase (MTGase) was fitted using one-step inactivation model. It was much more stable under 40 degrees C. The half-lives for the MTGase at 50 degrees C and 60 degrees C were only 20 min and 8 min, respectively. Spectroscopic studies of the enzyme suggested conformational transition from ordered secondary structural elements (alpha/beta-protein) to unordered structure during thermal denaturation. Some polyols could improve the thermal stability of the enzyme. Among the polyols examined, the prolonged half-lives of 40 min at 50 degrees C and 20 min at 60 degrees C were gained by adding 10% glycerol. The results of differential scanning calorimetric (DSC) analysis showed a distinct transition peak with a significant greater Tm and DeltaH for the MTGase mixed with polyols in comparison with the control, which indicated that the polyols could maintain the natural structure of the enzyme to some extent. The SDS-PAGE electrophoresis of cross-linked casein confirmed that the stabilizers could protect the MTGase from thermal denaturation.

  5. Examining possible effects of seawater pH decline on foraminiferal stable isotopes during the Paleocene-Eocene Thermal Maximum

    Science.gov (United States)

    Uchikawa, Joji; Zeebe, Richard E.

    2010-06-01

    A large body of paleoceanographic data for the Paleocene-Eocene Thermal Maximum (PETM) is based on foraminiferal stable carbon and oxygen isotope composition (δ13C and δ18O). However, the proxy records could be biased due to a “pH effect” on stable isotopes during times when the ocean became more acidic, as has been demonstrated for modern planktonic foraminifera. In this paper, we calculate the possible ranges of the pH effect on δ13C and δ18O during the PETM based on the relative pH decline (ΔpH) from the preperturbation steady state simulated by a carbon cycle model and the empirical relationships obtained from culture experiments with planktonic foraminifera. The model is configured with Eocene paleogeography and simulates ΔpH for surface, intermediate, and deep water in the major ocean basins in response to various carbon input scenarios (2000 to 5000 Pg C). For an array of scenarios, the modeled ΔpH of the surface ocean ranges from 0.1 to 0.28 units. This suggests that δ13C of planktonic foraminifera may be increased by up to 2.1‰ and δ18O may be increased by up to 0.7‰ (corresponding to over 3°C error in paleotemperature estimate). Under conditions in which the model best simulates the global CaCO3 dissolution pattern, we find marked differences in the deep-sea ΔpH between the Atlantic (-0.4) and Pacific oceans (-0.1). This would imply that the magnitude of the negative δ13C and δ18O excursions of benthic foraminifera in the Atlantic Ocean was dampened by up to 2.8‰ and 0.9‰ at maximum, respectively, relative to a constant pH scenario.

  6. Thermal and mechanical stability of retained austenite in aluminum-containing multiphase TRIP steels

    CERN Document Server

    Zwaag, S; Kruijver, S O; Sietsma, J

    2002-01-01

    Stability of retained austenite is the key issue to understand transformation-induced plasticity (TRIP) effect. In this work, both thermal stability and mechanical stability are investigated by thermo-magnetic as well as in situ conventional X-ray diffraction and micro synchrotron radiation diffraction measurements. The thermal stability in a 0.20C-1.52Mn-0.25Si-0.96Al (wt%) TRIP steel is studied in the temperature range between 5 and 300 K under a constant magnetic field of 5T. It is found that almost all austenite transforms thermally to martensite upon cooling to 5K and M sub s and M sub f temperatures are analyzed to be 355 and 115 K. Transformation kinetics on the fraction versus temperature relation are well described by a model based on thermodynamics. From the in situ conventional X-ray and synchrotron diffraction measurements in a 0.17C-1.46Mn-0.26Si-1.81Al (wt%) steel, the volume fraction of retained austenite is found to decrease as the strain increases according to Ludwigson and Berger relation. T...

  7. Structure-Activity Relationship Analysis of the Thermal Stabilities of Nitroaromatic Compounds Following Different Decomposition Mechanisms.

    Science.gov (United States)

    Li, Jiazhong; Liu, Huanxiang; Huo, Xing; Gramatica, Paola

    2013-02-01

    The decomposition behavior of energetic materials is very important for the safety problems concerning their production, transportation, use and storage, because molecular decomposition is intimately connected to their explosive properties. Nitroaromatic compounds, particularly nitrobenzene derivatives, are often considered as prototypical energetic molecules, and some of them are commonly used as high explosives. Quantitative structure-activity relationship (QSAR) represents a potential tool for predicting the thermal stability properties of energetic materials. But it is reported that constructing general reliable models to predict their stability and their potential explosive properties is a very difficult task. In this work, we make our efforts to investigate the relationship between the molecular structures and corresponding thermal stabilities of 77 nitrobenzene derivatives with various substituent functional groups (in ortho, meta and/or para positions). The proposed best MLR model, developed by the new software QSARINS, based on Genetic Algorithm for variable selection and with various validation tools, is robust, stable and predictive with R(2) of 0.86, QLOO (2) of 0.79 and CCC of 0.90. The results indicated that, though difficult, it is possible to build predictive, externally validated QSAR models to estimate the thermal stability of nitroaromatic compounds. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. Thermal stability of pulsed laser deposited iridium oxide thin films at low oxygen atmosphere

    Science.gov (United States)

    Gong, Yansheng; Wang, Chuanbin; Shen, Qiang; Zhang, Lianmeng

    2013-11-01

    Iridium oxide (IrO2) thin films have been regarded as a leading candidate for bottom electrode and diffusion barrier of ferroelectric capacitors, some process related issues need to be considered before integrating ferroelectric capacitors into memory cells. This paper presents the thermal stability of pulsed laser deposited IrO2 thin films at low oxygen atmosphere. Emphasis was given on the effect of post-deposition annealing temperature at different oxygen pressure (PO2) on the crystal structure, surface morphology, electrical resistivity, carrier concentration and mobility of IrO2 thin films. The results showed that the thermal stability of IrO2 thin films was strongly dependent on the oxygen pressure and annealing temperature. IrO2 thin films can stably exist below 923 K at PO2 = 1 Pa, which had a higher stability than the previous reported results. The surface morphology of IrO2 thin films depended on PO2 and annealing temperature, showing a flat and uniform surface for the annealed films. Electrical properties were found to be sensitive to both the annealing temperature and oxygen pressure. The room-temperature resistivity of IrO2 thin films with a value of 49-58 μΩ cm increased with annealing temperature at PO2 = 1 Pa. The thermal stability of IrO2 thin films as a function of oxygen pressure and annealing temperature was almost consistent with thermodynamic calculation.

  9. ALD Functionalized Nanoporous Gold: Thermal Stability, Mechanical Properties, and Catalytic Activity

    Energy Technology Data Exchange (ETDEWEB)

    Biener, M M; Biener, J; Wichmann, A; Wittstock, A; Baumann, T F; Baeumer, M; Hamza, A V

    2011-03-24

    Nanoporous metals have many technologically promising applications but their tendency to coarsen limits their long-term stability and excludes high temperature applications. Here, we demonstrate that atomic layer deposition (ALD) can be used to stabilize and functionalize nanoporous metals. Specifically, we studied the effect of nanometer-thick alumina and titania ALD films on thermal stability, mechanical properties, and catalytic activity of nanoporous gold (np-Au). Our results demonstrate that even only one-nm-thick oxide films can stabilize the nanoscale morphology of np-Au up to 1000 C, while simultaneously making the material stronger and stiffer. The catalytic activity of np-Au can be drastically increased by TiO{sub 2} ALD coatings. Our results open the door to high temperature sensor, actuator, and catalysis applications and functionalized electrodes for energy storage and harvesting applications.

  10. Study of fuzzy adaptive PID controller on thermal frequency stabilizing laser with double longitudinal modes

    Science.gov (United States)

    Mo, Qingkai; Zhang, Tao; Yan, Yining

    2016-10-01

    There are contradictions among speediness, anti-disturbance performance, and steady-state accuracy caused by traditional PID controller in the existing light source systems of thermal frequency stabilizing laser with double longitudinal modes. In this paper, a new kind of fuzzy adaptive PID controller was designed by combining fuzzy PID control technology and expert system to make frequency stabilizing system obtain the optimal performance. The experiments show that the frequency stability of the designed PID controller is similar to the existing PID controller (the magnitude of frequency stability is less than 10-9 in constant temperature and 10-7 in open air). But the preheating time is shortened obviously (from 10 minutes to 5 minutes) and the anti-disturbance capability is improved significantly (the recovery time needed after strong interference is reduced from 1 minute to 10 seconds).

  11. Studies into the Stability of 3-O-Glycosylated and 3,5-O-Diglycosylated Anthocyanins in Differently Purified Liquid and Dried Maqui (Aristotelia chilensis (Mol.) Stuntz) Preparations during Storage and Thermal Treatment.

    Science.gov (United States)

    Brauch, Johanna E; Kroner, Mareike; Schweiggert, Ralf M; Carle, Reinhold

    2015-10-07

    Anthocyanin stabilities in diluted and differently purified maqui preparations were assessed during storage and thermal treatment at different pH values. By sequentially depleting the matrix, the influence of polar low-molecular-weight matrix constituents and non-anthocyanin phenolics was shown to be negligible. In contrast, pH substantially affected thermal stabilities of differently glycosylated cyanidin and delphinidin derivatives. At pH 3.6, half-lives of 3-O-glycosides were substantially shorter than those of respective 3,5-O-diglycosides. However, at pH 2.2, an inverse stability behavior was observed. Findings were corroborated using isolated pigments. Upon heating, cyanidin derivatives were more stable than their respective delphinidins, but their stability was similar during storage. Anthocyanins in liquid samples were more stable when stored at 4 °C as compared to 20 °C, whereas those in dried powders revealed maximum stability throughout storage. The study contains a detailed discussion and mechanistic hypothesis for the above-mentioned findings, providing insights relevant for food applications of maqui anthocyanins.

  12. Quantification and analysis of color stability based on thermal transient behavior in white LED lamps.

    Science.gov (United States)

    Nisa Khan, M

    2017-09-20

    We present measurement and analysis of color stability over time for two categories of white LED lamps based on their thermal management scheme, which also affects their transient lumen depreciation. We previously reported that lumen depreciation in LED lamps can be minimized by properly designing the heat sink configuration that allows lamps to reach a thermal equilibrium condition quickly. Although it is well known that lumen depreciation degrades color stability of white light since color coordinates vary with total lumen power by definition, quantification and characterization of color shifts based on thermal transient behavior have not been previously reported in literature for LED lamps. Here we provide experimental data and analysis of transient color shifts for two categories of household LED lamps (from a total of six lamps in two categories) and demonstrate that reaching thermal equilibrium more quickly provides better stability for color rendering, color temperature, and less deviation of color coordinates from the Planckian blackbody locus line, which are all very important characterization parameters of color for white light. We report for the first time that a lamp's color degradation from the turn-on time primarily depends on thermal transient behavior of the semiconductor LED chip, which experiences a wavelength shift as well as a decrease in its dominant wavelength peak value with time, which in turn degrades the phosphor conversion. For the first time, we also provide a comprehensive quantitative analysis that differentiates color degradation due to the heat rise in GaN/GaInN LED chips and subsequently the boards these chips are mounted on-from that caused by phosphor heating in a white LED module. Finally, we briefly discuss why there are some inevitable trade-offs between omnidirectionality and color and luminous output stability in current household LED lamps and what will help eliminate these trade-offs in future lamp designs.

  13. Thermal effects in two-phase flow through face seals. Ph.D. Thesis

    Science.gov (United States)

    Basu, Prithwish

    1988-01-01

    When liquid is sealed at high temperature, it flashes inside the seal due to pressure drop and/or viscous heat dissipation. Two-phase seals generally exhibit more erratic behavior than their single phase counterparts. Thermal effects, which are often neglected in single phase seal analyses, play an important role in determining seal behavior under two-phase operation. It is necessary to consider the heat generation due to viscous shear, conduction into the seal rings and convection with the leakage flow. Analytical models developed work reasonably well at the two extremes - for low leakage rates when convection is neglected and for higher leakage rates when conduction is neglected. A preliminary model, known as the Film Coefficient Model, is presented which considers conduction and convection both, and allows continuous boiling over an extended region unlike the previous low-leakage rate model which neglects convection and always forces a discrete boiling interface. Another simplified, semi-analytical model, based on the assumption of isothermal conditions along the seal interafce, has been developed for low leakage rates. The Film Coefficient Model may be used for more accurate and realistic description.

  14. Air, aqueous and thermal stabilities of Ce3+ ions in cerium oxide nanoparticle layers with substrates

    KAUST Repository

    Naganuma, Tamaki

    2014-01-01

    Abundant oxygen vacancies coexisting with Ce3+ ions in fluorite cerium oxide nanoparticles (CNPs) have the potential to enhance catalytic ability, but the ratio of unstable Ce3+ ions in CNPs is typically low. Our recent work, however, demonstrated that the abundant Ce3+ ions created in cerium oxide nanoparticle layers (CNPLs) by Ar ion irradiation were stable in air at room temperature. Ce valence states in CNPs correlate with the catalytic ability that involves redox reactions between Ce3+ and Ce4+ ions in given application environments (e.g. high temperature in carbon monoxide gas conversion and immersion conditions in biomedical applications). To better understand the mechanism by which Ce3+ ions achieve stability in CNPLs, we examined (i) extra-long air-stability, (ii) thermal stability up to 500 °C, and (iii) aqueous stability of Ce 3+ ions in water, buffer solution and cell culture medium. It is noteworthy that air-stability of Ce3+ ions in CNPLs persisted for more than 1 year. Thermal stability results showed that oxidation of Ce 3+ to Ce4+ occurred at 350 °C in air. Highly concentrated Ce3+ ions in ultra-thin CNPLs slowly oxidized in water within 1 day, but stability was improved in the cell culture medium. Ce 3+ stability of CNPLs immersed in the medium was associated with phosphorus adsorption on the Ce3+ sites. This study also illuminates the potential interaction mechanisms of stable Ce3+ ions in CNPLs. These findings could be utilized to understand catalytic mechanisms of CNPs with abundant oxygen vacancies in their application environments. © The Royal Society of Chemistry 2014.

  15. Temperature-dependent thermal conductivity of flexible yttria-stabilized zirconia substrate via 3ω technique

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Shivkant; Yarali, Milad; Mavrokefalos, Anastassios [Department of Mechanical Engineering, University of Houston, Houston, TX (United States); Shervin, Shahab [Materials Science and Engineering Program, University of Houston, Houston, TX (United States); Venkateswaran, Venkat; Olenick, Kathy; Olenick, John A. [ENrG Inc., Buffalo, NY (United States); Ryou, Jae-Hyun [Department of Mechanical Engineering, University of Houston, Houston, TX (United States); Materials Science and Engineering Program, University of Houston, Houston, TX (United States); Texas Center for Superconductivity, University of Houston (TcSUH), Houston, TX (United States)

    2017-10-15

    Thermal management in flexible electronic has proven to be challenging thereby limiting the development of flexible devices with high power densities. To truly enable the technological implementation of such devices, it is imperative to develop highly thermally conducting flexible substrates that are fully compatible with large-scale fabrication. Here, we present the thermal conductivity of state-of-the-art flexible yttria-stabilized zirconia (YSZ) substrates measured using the 3ω technique, which is already commercially manufactured via roll-to-roll technique. We observe that increasing the grain size increases the thermal conductivity of the flexible 3 mol.% YSZ, while the flexibility and transparency of the sample are hardly affected by the grain size enlargement. We exhibit thermal conductivity values of up to 4.16 Wm{sup -1}K {sup -1} that is at least 4 times higher than state-of-the-art polymeric flexible substrates. Phonon-hopping model (PHM) for granular material was used to fit the measured thermal conductivity and accurately define the thermal transport mechanism. Our results show that through grain size optimization, YSZ flexible substrates can be realized as flexible substrates, that pave new avenues for future novel application in flexible electronics through the utilization of both their ceramic structural flexibility and high heat dissipating capability. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  16. Microstructure and Thermal Stability of A357 Alloy With and Without the Addition of Zr

    Science.gov (United States)

    Tzeng, Yu-Chih; Chengn, Vun-Shing; Nieh, Jo-Kuang; Bor, Hui-Yun; Lee, Sheng-Long

    2017-11-01

    The principal purpose of this research was to evaluate the effects of Zr on the microstructure and thermal stability of an A357 alloy that has been subjected to an aging treatment (T6) and thermal exposure (250 °C). The results show that the addition of Zr had a significant influence on the refinement of the grain size, which enhanced the hardness and tensile strength of the A357 alloy under the T6 condition. During thermal exposure at 250 °C, the rodlike metastable β'-Mg2Si precipitates transformed into coarse equilibrium phase β-Mg2Si precipitates, resulting in a significant drop in the hardness and tensile strength of the T6 heat-treated A357 alloy. However, after thermal exposure, coherent, finely dispersed Al3Zr precipitates were found to be formed in the T6 heat-treated A357 alloy. The addition of 0.1% Zr played a critical role in improving the high-temperature strength. Consequently, the A357 alloy with the addition of Zr demonstrated better mechanical properties at room temperature and high temperature than the alloy without Zr, in terms of both microstructure and thermal stability.

  17. Thermoelectric properties and thermal stability of layered chalcogenides, TlScQ2, Q = Se, Te.

    Science.gov (United States)

    Aswathy, Vijayakumar Sajitha; Sankar, Cheriyedath Raj; Varma, Manoj Raama; Assoud, Abdeljalil; Bieringer, Mario; Kleinke, Holger

    2017-12-12

    A few thallium based layered chalcogenides of α-NaFeO 2 structure-type are known for their excellent thermoelectric properties and interesting topological insulator nature. TlScQ 2 belongs to this structural category. In the present work, we have studied the electronic structure, electrical and thermal transport properties and thermal stability of the title compounds within the temperature range 2-600 K. Density functional theory (DFT) predicts a metallic nature for TlScTe 2 and a semiconducting nature for TlScSe 2 . DFT calculations also show significant lowering of energies of frontier bands upon inclusion of spin-orbit coupling contribution in the calculation. The electronic structure also shows the simultaneous occurrence of holes and electron pockets for the telluride. Experiments reveal that the telluride shows a semi-metallic behaviour whereas the selenide is a semiconductor. The thermoelectric properties for both the materials were also investigated. Both these materials possess very low thermal conductivity which is an attractive feature for thermoelectrics. However, they lack thermal stability and decompose upon warming above room temperature, as evidenced from high temperature powder X-ray diffraction and thermal analysis.

  18. Thermal Stability of Frozen Volatiles in the North Polar Region of Mercury

    Science.gov (United States)

    Paige, David A.; Siegler, Matthew A.; Harmon, John K.; Smith, David E.; Zuber, Maria T.; Neumann, Gregory A.; Solomon, Sean C.

    2012-01-01

    Earth-based radar observations have revealed the presence on Mercury of anomalously bright, depolarizing features that appear to be localized in the permanently shadowed regions of high-latitude impact craters [1]. Observations of similar radar signatures over a range of radar wavelengths implies that they correspond to deposits that are highly transparent at radar wavelengths and extend to depths of several meters below the surface [1]. Thermal models using idealized crater topographic profiles have predicted the thermal stability of surface and subsurface water ice at these same latitudes [2]. One of the major goals of the MESSENGER mission is to characterize the nature of radar-bright craters and presumed associated frozen volatile deposits at the poles of Mercury through complementary orbital observations by a suite of instruments [3]. Here we report on an examination of the thermal stability of water ice and other frozen volatiles in the north polar region of Mercury using topographic profiles obtained by the Mercury Laser Altimeter (MLA) instrument [4] in conjunction with a three-dimensional ray-tracing thermal model previously used to study the thermal environment of polar craters on the Moon [5].

  19. Tuning Thermal Transitions in Dry and Hydrated Polyelectrolyte Layer by Layer Assemblies with Ionic Strength and pH

    Science.gov (United States)

    Vidyasagar, Ajay; Lutkenhaus, Jodie

    2012-02-01

    Layer-by-layer (LbL) assemblies are of significant interest for their potential applications in diverse fields such as energy and drug delivery. However, characterizing their thermal properties has remained a challenge. Here, we present the characterization of dry and of hydrated LbL films containing strong polyelectrolytes poly(diallyldimethylammonium chloride) (PDAC) and poly(styrene sulfonate) PSS) using modulated differential scanning calorimetry (MDSC) and temperature controlled quartz crystal microbalance with dissipation (QCM-D). Our results suggest that hydrated exponentially growing (assembled from 0.25-1.25 M NaCl solutions) PDAC/PSS LbL films have glass transition temperatures (Tg's) between 48-51 ^oC, while linearly growing (assembled from 0 M NaCl) films did not. Other systems explored include poly(allylamine hydrochloride)/poly(acrylic acid)(PAH/PAA) LbL assemblies, which demonstrate linear/exponential growth depending on assembly pH conditions. These results support a standing hypothesis in that linear (or exponential) growth is observed for glassy (or rubbery) LbL films. We have also demonstrated for the first time, thermal transitions in thin PDAC/PSS LbL films using QCM-D by monitoring fluctuations in film hydration and viscoelasticity by probing the film's internal structure as a function of film depth.

  20. Improving structural stability of water-dispersed MCM-41 silica nanoparticles through post-synthesis pH aging process

    Energy Technology Data Exchange (ETDEWEB)

    Varache, Mathieu; Bezverkhyy, Igor [UMR 6303 CNRS-Université Bourgogne Franche-Comté, Laboratoire Interdisciplinaire Carnot de Bourgogne (France); Bouyer, Florence [Inserm U866, Equipe Chimiothérapie, métabolisme des lipides et réponse immunitaire anti-tumorale (France); Chassagnon, Rémi; Baras, Florence; Bouyer, Frédéric, E-mail: frederic.bouyer@u-bourgogne.fr [UMR 6303 CNRS-Université Bourgogne Franche-Comté, Laboratoire Interdisciplinaire Carnot de Bourgogne (France)

    2015-09-15

    The colloidal and structural stabilities of MCM-41 mesoporous silica nanoparticles (MSNs) are of great importance in order to prepare optimal nanovectors. In this paper, MSNs (approximatively 160 nm in diameter) were synthesized using n-cetyltrimethylammonium bromide as a template and tetraethyl orthosilicate as a silica source under high N{sub 2} flow (MSN/N{sub 2}) to obtain stable dispersions in water. The degradation of the porous nanoparticles was investigated by immersion in water. The morphology and the porous structure were studied by TEM, XRD, N{sub 2} sorption, and {sup 29}Si MAS NMR and were compared to that of MSNs prepared in ambient air (MSN/air). The volumetric properties of the MSN/N{sub 2} after 1 day in water were drastically more decreased than MSN/air (a pore volume decrease of 85 % for MSN/N{sub 2} and 59 % for MSN/air) and the 2D-hexagonal porous structure was totally lost. Furthermore, synthesizing MSNs under a high N{sub 2} flow leads to a decrease in the synthesis yield (45 % MSN/N{sub 2} and 75 % for MSN/air). The lower structural stability of the MSN/N{sub 2} is explained by the lower polycondensation degree of the MSN/N{sub 2} observed by {sup 29}Si MAS NMR (Q{sup 4}/Q{sup 3} = 0.86 for MSN/N{sub 2} and 1.61 for MSN/air) and the lower silica molar ratio in the nanomaterials (SiO{sub 2}/CTA = 3.9 for MSN/N{sub 2} 7.1 for MSN/air). This allows for enhanced solubilization of silica in water. Four strategies were hence evaluated in order to reinforce the porous structure of the MSNs. Among them, the most efficient route was based on a pH adjustment of the colloidal suspension (pH 7.5) after 2 h of synthesis without any purification and while keeping a N{sub 2} static atmosphere (called MSN/N{sub 2}/7.5). After 1 day in water, the volumetric and structural properties of MSN/N{sub 2}/7.5 were similar to that obtained for MSN/air. The improvement of the stability arose as a result of the increase in the silica condensation (Q{sup 4

  1. Study of thermal stability and degradation of fire resistant candidate polymers for aircraft interiors

    Science.gov (United States)

    Hsu, M. T. S.

    1976-01-01

    The thermochemistry of bismaleimide resins and phenolphthalein polycarbonate was studied. Both materials are fire-resistant polymers and may be suitable for aircraft interiors. The chemical composition of the polymers has been determined by nuclear magnetic resonance and infrared spectroscopy and by elemental analysis. Thermal properties of these polymers have been characterized by thermogravimetric analyses. Qualitative evaluation of the volatile products formed in pyrolysis under oxidative and non-oxidative conditions has been made using infrared spectrometry. The residues after pyrolysis were analyzed by elemental analysis. The thermal stability of composite panel and thermoplastic materials for aircraft interiors was studied by thermogravimetric analyses.

  2. The thermal stability of the carbon-palladium films for hydrogen sensor applications

    Science.gov (United States)

    Rymarczyk, Joanna; Czerwosz, ElŻbieta; Diduszko, Ryszard; Kozłowski, Mirosław

    2017-08-01

    The thermal stability of two types of C-Pd films prepared in PVD process were studied. These films are composed of Pd nanograins embedded in a multiphase carbonaceous matrix. These films were distinguished by Pd content. These films were annealed in a range of temperatures 50÷1000°C. The structural, topographical and molecular changes were studied by scanning electron microscopy (SEM), infrared spectroscopy (FTIR) and X-ray diffraction (XRD) methods. The results show that investigated films are thermally stable up to 200°C.

  3. Coordinated Stability Control of Wind-Thermal Hybrid AC/DC Power System

    Directory of Open Access Journals (Sweden)

    Zhiqing Yao

    2015-01-01

    Full Text Available The wind-thermal hybrid power transmission will someday be the main form of transmitting wind power in China but such transmission mode is poor in system stability. In this paper, a coordinated stability control strategy is proposed to improve the system stability. Firstly, the mathematical model of doubly fed wind farms and DC power transmission system is established. The rapid power controllability of large-scale wind farms is discussed based on DFIG model and wide-field optical fiber delay feature. Secondly, low frequency oscillation and power-angle stability are analyzed and discussed under the hybrid transmission mode of a conventional power plant with wind farms. A coordinated control strategy for the wind-thermal hybrid AC/DC power system is proposed and an experimental prototype is made. Finally, real time simulation modeling is set up through Real Time Digital Simulator (RTDS, including wind power system and synchronous generator system and DC power transmission system. The experimental prototype is connected with RTDS for joint debugging. Joint debugging result shows that, under the coordinated control strategy, the experimental prototype is conductive to enhance the grid damping and effectively prevents the grid from occurring low frequency oscillation. It can also increase the transient power-angle stability of a power system.

  4. Stabilization of Organic Matter by Biochar Application in Compost-amended Soils with Contrasting pH Values and Textures

    Directory of Open Access Journals (Sweden)

    Shih-Hao Jien

    2015-09-01

    Full Text Available Food demand and soil sustainability have become urgent concerns because of the impacts of global climate change. In subtropical and tropical regions, practical management that stabilizes and prevents organic fertilizers from rapid decomposition in soils is necessary. This study conducted a short-term (70 days incubation experiment to assess the effects of biochar application on the decomposition of added bagasse compost in three rural soils with different pH values and textures. Two rice hull biochars, produced through slow pyrolization at 400 °C (RHB-400 and 700 °C (RHB-700, with application rates of 1%, 2%, and 4% (w/w, were separately incorporated into soils with and without compost (1% (w/w application rate. Experimental results indicated that C mineralization rapidly increased at the beginning in all treatments, particularly in those involving 2% and 4% biochar. The biochar addition increased C mineralization by 7.9%–48% in the compost-amended soils after 70 days incubation while the fractions of mineralized C to applied C significantly decreased. Moreover, the estimated maximum of C mineralization amount in soils treated with both compost and biochar were obviously lower than expectation calculated by a double exponential model (two pool model. Based on the micromorphological observation, added compost was wrapped in the soil aggregates formed after biochar application and then may be protected from decomposing by microbes. Co-application of compost with biochar may be more efficient to stabilize and sequester C than individual application into the studied soils, especially for the biochar produced at high pyrolization temperature.

  5. Thermal Stability of Modified i-Motif Oligonucleotides with Naphthalimide Intercalating Nucleic Acids

    DEFF Research Database (Denmark)

    El-Sayed, Ahmed Ali; Pedersen, Erik B.; Khaireldin, Nahid Y.

    2016-01-01

    In continuation of our investigation of characteristics and thermodynamic properties of the i-motif 5′-d[(CCCTAA)3CCCT)] upon insertion of intercalating nucleotides into the cytosine-rich oligonucleotide, this article evaluates the stabilities of i-motif oligonucleotides upon insertion of naphtha......In continuation of our investigation of characteristics and thermodynamic properties of the i-motif 5′-d[(CCCTAA)3CCCT)] upon insertion of intercalating nucleotides into the cytosine-rich oligonucleotide, this article evaluates the stabilities of i-motif oligonucleotides upon insertion...... of naphthalimide (1H-benzo[de]isoquinoline-1,3(2H)-dione) as the intercalating nucleic acid. The stabilities of i-motif structures with inserted naphthalimide intercalating nucleotides were studied using UV melting temperatures (Tm) and circular dichroism spectra at different pH values and conditions (crowding...

  6. Metal ion-specific thermal stability of bacterial S-Layers

    Energy Technology Data Exchange (ETDEWEB)

    Drobot, Bjoern; Raff, Johannes [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Div. Biogeochemistry; Fahmy, Karim [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Div. Biophysics

    2016-07-01

    Many bacteria are covered by a surface layer (S-layer), i.e., a para-crystalline two-dimensional array of proteins which control cell shape, act as molecular sieves and have potential applications as radionuclide-binding material for bioremediation of polluted areas. Knowledge and control of the metal-dependent stability of the purified proteins is required for their technical application. Here, we have explored by differential scanning calorimetry the thermal stability of the S-layer protein slp-B53 from Lysinibacillus sphaericus, a Gram-positive bacterium isolated from a uranium mining waste pile [1].

  7. Pd-based alloy nanoclusters in ion-implanted silica: Formation and stability under thermal annealing

    Energy Technology Data Exchange (ETDEWEB)

    Battaglin, G.; Cattaruzza, E.; De Marchi, G.; Gonella, F.; Mattei, G. E-mail: mattei@padova.infm.it; Maurizio, C.; Mazzoldi, P.; Parolin, M.; Sada, C.; Calliari, I

    2002-05-01

    In this work we report on the formation and stability under thermal annealing of Pd-Cu and Pd-Ag alloy nanoclusters obtained by sequential ion implantation in silica. The role of the annealing atmosphere on the alloy cluster formation and stability is investigated. A comparison is made with similar alloy-based systems obtained by sequential ion implantation in silica of Au-Ag or Au-Cu followed by annealing under similar conditions, in order to evidence the peculiar effect of the various metals in controlling the alloy evolution and/or decomposition.

  8. Sodium dodecyl sulfate (SDS) effect on the thermal stability of oxy-HbGp: dynamic light scattering (DLS) and small angle X-ray scattering (SAXS) studies.

    Science.gov (United States)

    Carvalho, José Wilson P; Alves, Fernanda Rosa; Batista, Tatiana; Carvalho, Francisco Adriano O; Santiago, Patrícia S; Tabak, Marcel

    2013-11-01

    Glossoscolex paulistus (HbGp) hemoglobin is an oligomeric protein, presenting a quaternary structure constituted by 144 globin and 36 non-globin chains (named linkers) with a total molecular mass of 3.6 MDa. SDS effects on the oxy-HbGp thermal stability were studied, by DLS and SAXS, at pH 5.0, 7.0 and 9.0. DLS and SAXS data show that the SDS-oxy-HbGp interactions induce a significant decrease of the protein thermal stability, with the formation of larger aggregates, at pH 5.0. At pH 7.0, oxy-HbGp undergoes complete oligomeric dissociation, with increase of temperature, in the presence of SDS. Besides, oxy-HbGp 3.0mg/mL, pH 7.0, in the presence of SDS, has the oligomeric dissociation process reduced as compared to 0.5mg/mL of protein. At pH 9.0, oxy-HbGp starts to dissociate at 20 °C, and the protein is totally dissociated at 50 °C. The thermal dissociation kinetic data show that oxy-HbGp oligomeric dissociation at pH 7.0, in the presence of SDS, is strongly dependent on the protein concentration. At 0.5mg/mL of protein, the oligomeric dissociation is complete and fast at 40 and 42 °C, with kinetic constants of (2.1 ± 0.2) × 10(-4) and (5.5 ± 0.4) × 10(-4) s(-1), respectively, at 0.6 mmol/L SDS. However, at 3.0mg/mL, the oligomeric dissociation process starts at 46 °C, and only partial dissociation, accompanied by aggregates formation is observed. Moreover, our data show, for the first time, that, for 3.0mg/mL of protein, the oligomeric dissociation, denaturation and aggregation phenomena occur simultaneously, in the presence of SDS. Our present results on the surfactant-HbGp interactions and the protein thermal unfolding process correspond to a step forward in the understanding of SDS effects. Copyright © 2013 Elsevier B.V. All rights reserved.

  9. Shape-stabilized phase change materials with high thermal conductivity based on paraffin/graphene oxide composite

    International Nuclear Information System (INIS)

    Mehrali, Mohammad; Latibari, Sara Tahan; Mehrali, Mehdi; Metselaar, Hendrik Simon Cornelis; Silakhori, Mahyar

    2013-01-01

    Highlights: ► The composite PCM was prepared with impregnation method. ► Shapes stabilized phase change material made with paraffin and GO composite. ► Determine effects of GO composite on shape stabilized PCM properties. ► The composite PCM has good thermal stability and form-stability. ► The composite PCM has much higher thermal conductivity than that of paraffin. - Abstract: This paper mainly focuses on the preparation, characterization, thermal properties and thermal stability and reliability of new form-stable composite phase change materials (PCMs) prepared by vacuum impregnation of paraffin within graphene oxide (GO) sheets. SEM and FT-IR techniques and TGA and DSC analysis are used for characterization of material and thermal properties. The composite PCM contained 48.3 wt.% of paraffin without leakage of melted PCM and therefore this composite found to be a form-stable composite PCM. SEM results indicate that the paraffin bounded into the pores of GO. FT-IR analysis showed there was no chemical reaction between paraffin and GO. Temperatures of melting and freezing and latent heats of the composite were 53.57 and 44.59 °C and 63.76 and 64.89 kJ/kg, respectively. Thermal cycling tests were done by 2500 melting/freezing cycling for verification of the form-stable composite PCM in terms of thermal reliability and chemical stability. Thermal conductivity of the composite PCM was highly improved from 0.305 to 0.985 (W/mk). As a result, the prepared paraffin/GO composite is appropriate PCM for thermal energy storage applications because of their acceptable thermal properties, good thermal reliability, chemical stability and thermal conductivities

  10. Oxidative stability, thermal stability and acceptability of coconut oil flavored with essential oils from black pepper and ginger.

    Science.gov (United States)

    Chandran, Janu; Nayana, N; Roshini, N; Nisha, P

    2017-01-01

    The present study investigates the oxidative and thermal stability of flavoured oils developed by incorporating essential oils from black pepper and ginger to coconut oil (CNO) at concentrations of 0.1 and 1.0% (CNO P-0.1 , CNO P-1 , CNO G-0.1 , CNO G-1 ). The stability of oils were assessed in terms of free fatty acids, peroxide, p -anisidine, conjugated diene and triene values and compared with CNO without any additives and a positive control with synthetic antioxidant TBHQ (CNO T ). It was found that the stability of CNO P-1 and CNO G-1 were comparable with CNO T at both study conditions. The possibility of flavoured oil as a table top salad oil was explored by incorporating the same in vegetable salad and was found more acceptable than the control, on sensory evaluation. The synergetic effect of essential oil as a flavour enhancer and a powerful natural antioxidant that can slow down the oxidation of fats was established in the study.

  11. Fabrication and characterization of poly (bisphenol A borate) with high thermal stability

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Shujuan [Department of Applied Chemistry, School of Science, Xi’an Jiaotong University, Xi’an 710049 (China); Wang, Xiao [Department of Chemical Engineering, School of Chemical Engineering and Technology, Xi’an Jiaotong University, Xi’an 710049 (China); Jia, Beibei [Department of Applied Chemistry, School of Science, Xi’an Jiaotong University, Xi’an 710049 (China); Jing, Xinli, E-mail: xljing@mail.xjtu.edu.cn [Department of Applied Chemistry, School of Science, Xi’an Jiaotong University, Xi’an 710049 (China); MOE Key Laboratory for Nonequilibrium Synthesis and Modulation of Condensed Matter, Xi’an, 710049 (China)

    2017-01-15

    Highlights: • PBAB with excellent thermal resistance and high char yield was synthesized. • The chemical reaction of BPA with BA, and chemical structure of PBAB were studied. • PBAB show excellent thermal resistance in N{sub 2} and air atmospheres. • The thermal stability of PBAB is greatly influenced by boron content. • Boron oxide and boron carbide are formed during the pyrolysis of PBAB. - Abstract: In this work, poly (bisphenol A borate) (PBAB), which has excellent thermal resistance and a high char yield, was synthesized via a convenient A{sub 2} + B{sub 3} strategy by using bisphenol A (BPA) and boric acid (BA). The chemical reaction between BPA and BA and the chemical structure of PBAB were investigated. The results demonstrate that PBAB consists of aromatic, Ph–O–B and B–O–B structures, as well as a small number of boron hydroxyl groups and phenolic hydroxyl groups. The thermal properties of PBAB were studied by DMA and TGA. The results indicate that the glass transition temperature and char yield are gradually enhanced by increasing the boron content, where the char yield of PBAB at 800 °C in nitrogen (N{sub 2}) reaches up to 71.3%. It is of particular importance that PBAB show excellent thermal resistance in N{sub 2} and air atmospheres. By analysing the pyrolysis of PBAB, the high char yield of PBAB can be attributed to the formation of boron oxide and boron carbide at high temperatures, which reduced the release of volatile carbon dioxide and improved the thermal stability of the carbonization products. This study provides a new perspective on the design of novel boron-containing polymers and possesses significant potential for the improvement of the comprehensive performance of thermosetting resins to broaden their applicability in the field of advanced composites.

  12. Probing the Molecular Ordering and Thermal Stability of Azopolymer Layer-by-Layer Films by Second-Harmonic Generation.

    Science.gov (United States)

    Silva, Heurison S; Miranda, Paulo B

    2016-10-04

    Polyelectrolyte layer-by-layer (LbL) films have many applications, but several parameters and procedures during film fabrication determine their morphology and molecular arrangement, with important practical consequences. Here we have used optical second-harmonic generation (SHG) to investigate the molecular ordering of LbL films containing the anionic azopolymer PS-119 and the cationic polyelectrolyte PAH. We show that spontaneous drying leads to laterally homogeneous and isotropic films, while the opposite occurs for nitrogen-flow drying. The effect of film thickness and pH of the assembling/rinsing solutions on the molecular ordering was also investigated. The optical nonlinearity tends to significantly decrease for thicker films (∼10 bilayers), and a slight alternation of SHG intensity for films with odd or even number of layers (complete vs incomplete bilayers) was also observed, which results from the reorientation of azopolymer groups in the last layer after adsorption of an additional PAH layer. We propose a qualitative electrostatic model to explain the pH dependence of film growth and azopolymer orientation, which is based on changes of the charge density of the substrate and PAH and on different ionic screening of electrostatic interactions at various pH values. We also found that the nonlinear response presents a gradual and significant reduction upon heating, which is inconsistent with a glass transition temperature for these ultrathin LbL films. The thermal stability is improved with a combination of low ionic strength and higher charge density of the polyelectrolytes and substrate, which promotes better interlayer complexation. The SHG signal is recovered upon cooling, although for some conditions the molecular arrangement became anisotropic after a heating/cooling cycle. Such detailed information about the structural order of thin nonlinear optical azopolymer LbL films demonstrates that SHG is a powerful technique to probe the film structure at

  13. Colour interceptions, thermal stability and surface morphology of polyester metal complexes

    International Nuclear Information System (INIS)

    Zohdy, M.H.

    2005-01-01

    Chelating copolymers via grafting of acrylic acid (AAc) and acrylamide (AAm/AAc) comonomer mixture onto polyester micro fiber fabrics (PETMF) using gamma-radiation technique were prepared. The prepared graft chains (PETMF-g-AAc) and (PETMF-g-PAAc/PAAm) acted as chelating sites for some selected transition metal ions. The prepared graft copolymers and their metal complexes were characterized using thermogravimetric analysis (TGA), colour parameters and surface morphology measurements. The colour interception and strength measurements showed that the metal complexation is homogeneously distributed. The results showed that the thermal stability of PETMF was improved after graft copolymerization and metal complexes. Moreover, the degree of grafting enhanced the thermal stability values of the grafted and complexed copolymers up to 25% of magnitude, on the other hand the activation energy of the grafted-copolymer with acrylic acid increased up to 80%. The SEM observation gives further supports to the homogenous distribution of grafting and metal complexation

  14. Preparation of polyvinyl alcohol graphene oxide phosphonate film and research of thermal stability and mechanical properties.

    Science.gov (United States)

    Li, Jihui; Song, Yunna; Ma, Zheng; Li, Ning; Niu, Shuai; Li, Yongshen

    2018-05-01

    In this article, flake graphite, nitric acid, peroxyacetic acid and phosphoric acid are used to prepare graphene oxide phosphonic and phosphinic acids (GOPAs), and GOPAs and polyvinyl alcohol (PVA) are used to synthesize polyvinyl alcohol graphene oxide phosphonate and phosphinate (PVAGOPs) in the case of faint acidity and ultrasound irradiation, and PVAGOPs are used to fabricate PVAGOPs film, and the structure and morphology of GOPAs, PVAGOPs and PVAGOPs film are characterized, and the thermal stability and mechanical properties of PVAGOPs film are investigated. Based on these, it has been proved that GOPAs consist of graphene oxide phosphonic acid and graphene oxide phosphinic acid, and there are CP covalent bonds between them, and PVAGOPs are composed of GOPAs and PVA, and there are six-member lactone rings between GOPAs and PVA, and the thermal stability and mechanical properties of PVAGOPs film are improved effectively. Copyright © 2018 Elsevier B.V. All rights reserved.

  15. Influence of Cellulose on the Mechanical and Thermal Stability of ABS Plastic Composites

    Directory of Open Access Journals (Sweden)

    K. Crews

    2016-01-01

    Full Text Available Microcrystalline cellulose was explored as possible biodegradable fillers in the fabrication of ABS plastic composites. TGA indicates that upon inclusion of cellulose microcrystals the thermal stability of the ABS plastics was improved significantly when compared to the neat ABS plastic counterparts. Furthermore, inclusion of extracted cellulose from plant biomass showed a higher thermal stability with maximum decomposition temperatures around 131.95°C and 124.19°C for cellulose from cotton and Hibiscus sabdariffa, respectively, when compared to that of the purchased cellulose. In addition, TMA revealed that the average CTE value for the neat ABS and 1 : 1 ratio of cellulose to ABS fabricated in this study was significantly lower than the reported CTE (ca. 73.8 μm/m°C.

  16. Thermal stability and structural characteristics of PTHF–Mmt organophile nanocomposite

    Directory of Open Access Journals (Sweden)

    Youcef Hattab

    2015-05-01

    The objective of this study is to use organophilized montmorillonites in the presence of monomer tetrahydrofuran to obtain polytétrahydrofuran montmorillonites (PTHF–Mmt of composites by polymerization in situ. The organophilisation of the Mmt is formed by active cationic surface. The obtained results show an increase in the distance inside the reticular in the diffractograms of X-rays (DRX and the appearance of absorption bands of the characteristics of polytétrahydrofuran on the spectra of infrared spectroscopy (IR, which indicate pre-polymerization of tetrahydrofuran in the galleries of clay and, therefore, the obtaining of a nanocomposite. We have also studied the thermal stability of the samples by differential analysis calorimetric (DSC analysis, and we can conclude that the nanocomposites are stabilized thermally by the presence of clay in the matrix.

  17. Grain growth and thermal stability accompanying recrystallization in undercooled Ni-3at.%Sn alloy

    International Nuclear Information System (INIS)

    Chen, Z.; Chen, Q.; Shen, C.J.; Liu, F.

    2015-01-01

    The grain growth and thermal stability after recrystallization in as-solidified highly undercooled Ni-3at.%Sn alloy melt were investigated. As for undercooled Ni-3at.%Sn alloy, a transition from dendritic to granular crystals occurred when ΔT≥ΔT * , which was induced by the plastic deformation of dendrites and subsequent recrystallization. On this basis, the subsequent grain growth and solute segregation accompanying recalescence were calculated by a recently proposed thermo-kinetic model, which showed close agreement with the experimental results. It is concluded that the grain growth process was interrelated to recalescence, solute trapping and solute segregation of Sn atoms captured by solute trapping, which was responsible for the reduction of grain boundary energy and improvement of thermal stability. - Highlights: • A transition from dendritic to granular crystals occurred when ΔT≥ΔT * . • The grain growth accompanying recalescence was calculated. • A close agreement with the experimental results was shown

  18. Stability and color changes of thermally treated betanin, phyllocactin, and hylocerenin solutions.

    Science.gov (United States)

    Herbach, Kirsten M; Stintzing, Florian C; Carle, Reinhold

    2006-01-25

    Thermal degradation of betanin, phyllocactin (malonyl-betanin), and hylocerenin (3' '-hydroxy-3' '-methyl-glutaryl-betanin) solutions isolated from purple pitaya (Hylocereus polyrhizus [Weber] Britton and Rose) was monitored by spectrophotometric and high-performance liquid chromatography-diode array detection (HPLC-DAD) analyses. For betanin and phyllocactin solutions, the color shift upon thermal treatment was found to be nearly identical, while hylocerenin samples exhibited an intelligibly higher chromatic steadiness. Betanin proved to be the most stable individual pigment structure, while the enhanced tinctorial stability of the integral phyllocactin and especially hylocerenin solutions was due to the formation of red degradation products exhibiting improved color retention as opposed to their respective genuine pigments. Individual structure-related stability characteristics can exclusively be assessed by HPLC-DAD analyses and may not be noticed by mere spectrophotometric assessment of color and tinctorial strength.

  19. Radial effects in heating and thermal stability of a sub-ignited tokamak

    International Nuclear Information System (INIS)

    Fuchs, V.; Shoucri, M.M.; Thibaudeau, G.; Harten, L.; Bers, A.

    1982-02-01

    The existence of thermally stable sub-ignited equilibria of a tokamak reactor, sustained in operation by a feedback-controlled supplementary heating source, is demonstrated. The establishment of stability depends on a number of radially non-uniform, nonlinear processes whose effect is analyzed. One-dimensional (radial) stability analyses of model transport equations, together with numerical results from a 1-D transport code, are used in studying the heating of DT-plasmas in the thermonuclear regime. Plasma core supplementary heating is found to be a thermally more stable process than bulk heating. In the presence of impurity line radiation, however, core-heated temperature profiles may collapse, contracting inward from the limiter, the result of an instability caused by the increasing nature of the radiative cooling rate, with decreasing temperature. Conditions are established for the realization of a sub-ignited high-Q, toroidal reactor plasma with appreciable output power

  20. Studies on the parameters controlling the stability of the TET peptidase superstructure from Pyrococcus horikoshii revealed a crucial role of pH and catalytic metals in the oligomerization process.

    Science.gov (United States)

    Rosenbaum, Eva; Ferruit, Mylène; Durá, M Asunción; Franzetti, Bruno

    2011-10-01

    The TET proteases from Pyrococcus horikoshii are metallopeptidases that form large dodecameric particles with high thermal stability. The influence of various physico-chemical parameters on PhTET3 quaternary structure was investigated. Analytical ultracentrifugation and biochemical analyses showed that the PhTET3 quaternary structure and enzymatic activity are maintained in high salt and that the complex is stable under extreme acidic conditions. Under basic pH conditions the complex disassembled into a low molecular weight species that was identified as folded dimer. Metal analyses showed that the purified enzyme only contains two equivalent of zinc per monomer, corresponding to the metal ions responsible for catalytic activity. When these metals were removed by EDTA treatment, the complex dissociated into the same dimeric species as those observed at high pH. Dodecameric TET particles were obtained from the metal free dimers when 2mM of divalent ions were added to the protein samples. Most of the dimers remained assembled at high temperature. Thus, we have shown that dimers are the building units in the TET oligomerization pathway and that the active site metals are essential in this process. Copyright © 2010 Elsevier B.V. All rights reserved.

  1. Effect of temperature, pH and metal lons on the activity and stability of alkaline protease from novel bacillus licheniformis mzk03

    International Nuclear Information System (INIS)

    Sayem, S.M.A.; Hoq, M.M.; Alam, M.J.

    2006-01-01

    The effect of temperature, pH and metal ions on the activity and stability of crude protease from Bacillus licheniformis MZK03 was studied. The fermentation in shake culture revealed that maximum level of enzyme was produced at 37 degree C and pH 8.5 after 39 hr at 120 rpm. It lost its activity rapidly above 50 degree C and half-life of the protease at this temperature was 50 min with optimum activity at 40 degree C. It was most stable at pH 8.5 and lost its activity rapidly above pH 10.0, and at pH 11.0 reached 30% of the activity obtained at pH 9.0. The enzyme lost its activity completely at pH 13.0. Optimum proteolytic activity was found at 40 degree C and pH 9.5. The enzyme activity was accelerated by the addition of Mg/sup 2+/, Ca/sup 2+/ and Mn/sup 2+/, whereas it was inhibited by Hg/sup 2+/. (author)

  2. Thermal Stabilization of 233UO2, 233UO3, and 233U3O8

    International Nuclear Information System (INIS)

    Thein, S.M.; Bereolos, P.J.

    2000-01-01

    This report identifies an appropriate thermal stabilization temperature for 233 U oxides. The temperature is chosen principally on the basis of eliminating moisture and other residual volatiles. This report supports the U. S. Department of Energy (DOE) Standard for safe storage of 233 U (DOE 2000), written as part of the response to Recommendation 97-1 of the Defense Nuclear Facilities Safety Board (DNFSB), addressing safe storage of 233 U

  3. Thermal Stability and Magnetic Properties of Polyvinylidene Fluoride/Magnetite Nanocomposites

    OpenAIRE

    Ouyang, Zen-Wei; Chen, Erh-Chiang; Wu, Tzong-Ming

    2015-01-01

    This work describes the thermal stability and magnetic properties of polyvinylidene fluoride (PVDF)/magnetite nanocomposites fabricated using the solution mixing technique. The image of transmission electron microscopy for PVDF/magnetite nanocomposites reveals that the 13 nm magnetite nanoparticles are well distributed in PVDF matrix. The electroactive β-phase and piezoelectric responses of PVDF/magnetite nanocomposites are increased as the loading of magnetite nanoparticles increases. The pi...

  4. Proteosynthetic elongation factor EF-Tu domains: Thermal stability, adaptation and functions

    Czech Academy of Sciences Publication Activity Database

    Jonák, Jiří; Šanderová, Hana; Hůlková, Marta; Maloň, Petr; Krásný, Libor; Kepková, M.

    2009-01-01

    Roč. 16, 1a (2009), b23-b24 ISSN 1211-5894. [Meeting of the Czechoslovak and Slovak Biologists /7./. 12.03.2009-14.03.2009, Nové Hrady] R&D Projects: GA MŠk 2B06065; GA MZd NR9138 Institutional research plan: CEZ:AV0Z50520514; CEZ:AV0Z40550506 Keywords : EF-Tu * proteosynthetic elongation factor * thermal stability Subject RIV: EB - Genetics ; Molecular Biology

  5. Thermal stability of magnesium alloy AZ91 prepared by severe plastic deformation

    Directory of Open Access Journals (Sweden)

    Roman Štěpánek

    2013-12-01

    Full Text Available This paper deals with the thermal stability of ultrafine-grained alloy AZ91 prepared by means of ECAP (Equal Channel Angular Pressing method. Annealing experiments were conducted isochronally for 30 minutes in the temperature range of 220 to 400 °C in argon atmosphere. EBSD (Electron Backscatter Diffraction method was used to image the changes in microstructure due to increased temperature.

  6. Thermal-Stability and Reconstitution Ability of Listeria Phages P100 and A511

    Directory of Open Access Journals (Sweden)

    Hanie Ahmadi

    2017-12-01

    Full Text Available The study evaluated the thermal-stability of Listeria phages P100 and A511 at temperatures simulating the preparation of ready-to-eat meats. The phage infectivity after heating to 71°C and holding for a minimum of 30 s, before eventually cooling to 4°C were examined. Higher temperatures of 75, 80, and 85°C were also tested to evaluate their effect on phages thermal-stability. This study found that despite minor differences in the amino acid sequences of their structural proteins, the two phages responded differently to high temperatures. P100 activity declined at least 10 log (PFU mL-1 with exposure to 71°C (30 s and falling below the limit of detection (1 log PFU mL-1 while, A511 dropped from 108 to 105 PFU mL-1. Cooling resulted in partial reconstitution of P100 phage particles to 103 PFU mL-1. Exposure to 75°C (30 s abolished A511 activity (8 log PFU mL-1 and both phages showed reconstitution during cooling phase after exposure to 75°C. P100 exhibited reconstitution after treatment at 80°C (30 s, conversely A511 showed no reconstitution activity. Heating P100 to 85°C abolished the reconstitution potential. Substantial differences were found in thermal-stability and reconstitution of the examined phages showing A511 to be more thermo-stable than P100, while P100 exhibited reconstitution during cooling after treatment at 80°C which was absent in A511. The differences in predicted melting temperatures of structural proteins of P100 and A511 were consistent with the observed differences in thermal stability and morphological changes observed with transmission electron microscopy.

  7. Short-term thermal stability of transformer and motor oils at wide range of moisture contents

    Science.gov (United States)

    Volosnikov, D. V.; Povolotskiy, I. I.; Skripov, P. V.

    2018-01-01

    Method of controlled pulse heating of a wire probe was used for studying heat transfer and thermal stability of energy oils and motor oils in the presence of low quantities of moisture. The technique of two-pulse heating is the most suitable method for monitoring the actual state of oils. A distinct signal-response accompanying the appearance of moisture in the tested sample has been revealed.

  8. Novel PEG functionalized graphene nanosheets: enhancement of dispersibility and thermal stability

    Science.gov (United States)

    Zhang, Shupeng; Xiong, Pan; Yang, Xujie; Wang, Xin

    2011-05-01

    A series of polyethylene glycol (PEG) functionalized graphene sheet hybrid materials (FGHMs) have been successfully synthesized via ester linkages. Interestingly, our products can be dispersed in both polar/protic solvents and nonpolar/nonprotic ones, which differ significantly from previously reported systems and are of great value in the wide-spread application of these ``carbon nanosheet'' based materials by solution-phase processing. Furthermore, the addition of PEG-modified carbon nanosheets as nanofillers significantly improves the thermal stability of the bulk polymers. In our case, an increase of 35 K in thermal stability can be obtained for PEG4000 after filling with as low as 1 wt % of the PEG modified carbon sheets, suggesting their great potential as novel nanofillers in industry.A series of polyethylene glycol (PEG) functionalized graphene sheet hybrid materials (FGHMs) have been successfully synthesized via ester linkages. Interestingly, our products can be dispersed in both polar/protic solvents and nonpolar/nonprotic ones, which differ significantly from previously reported systems and are of great value in the wide-spread application of these ``carbon nanosheet'' based materials by solution-phase processing. Furthermore, the addition of PEG-modified carbon nanosheets as nanofillers significantly improves the thermal stability of the bulk polymers. In our case, an increase of 35 K in thermal stability can be obtained for PEG4000 after filling with as low as 1 wt % of the PEG modified carbon sheets, suggesting their great potential as novel nanofillers in industry. Electronic Supplementary Information (ESI) available: Table S1: Digital pictures of several typical hybrid materials dispersed in water and 22 organic solvents; Video 1: GO-PEG400 can be re-dispersed in the isooctane by simply turning the vials up and down. See DOI: 10.1039/c0nr00923g

  9. Why collagens best survived in fossils? Clues from amino acid thermal stability.

    Science.gov (United States)

    Wang, Shuang-Yin; Cappellini, Enrico; Zhang, Hong-Yu

    2012-05-25

    Explaining why type I collagens are preferentially preserved in the geological time scale remains a challenge. Several pieces of evidence indicate that its rich content in the bone and its unique, stable structure played key roles in its preservation. By considering the distinct thermal stability of amino acids, we reveal that the elevated abundance of thermostable amino acid residues in type I collagens also contribute to its survival. Copyright © 2012 Elsevier Inc. All rights reserved.

  10. Improvement of thermal-stability of enzyme immobilized onto mesoporous zirconia

    Directory of Open Access Journals (Sweden)

    Yuichi Masuda

    2014-03-01

    Thereafter, FDH immobilized on MPZ showed higher catalytic activity than that on MPS. Enhancement of catalytic activity was obtained by improving the substrate affinity derived from interparticle voids of MPZ. In addition, the FDH immobilized on MPZ had a very great higher thermal stability. Further investigation using transmittance Infrared spectroscopy indicated that the high-order structure of the FDH immobilized on MPZ did not get altered after the heat-treatment.

  11. Design of directional prism resonator made DPL operate in TEM00 mode with thermal stability

    Science.gov (United States)

    Lu, Changyong; Wang, Xiaobing; Sun, Bin; Guo, Yanlong; Wang, Guchang; Lin, Yi; Wan, Qiang

    2005-01-01

    An alignment-free directional prism resonator that ensures the laser TEM00 mode with thermal stability in a certain range is designed by using g* parameter equivalent method. The output of all solid state laser is about of 150mJ, and the beam divergence is of 3mrad with 20Hz repetition rate, moreover, when the laser operates from 10 to 30Hz, the beam divergence is steady. This laser meets the needs of special engineering application.

  12. Thermal stability of the human blood serum acid alpha(1)-glycoprotein in acidic media

    Czech Academy of Sciences Publication Activity Database

    Hofbauerová, Kateřina; Kopecký ml., Vladimír; Sýkora, J.; Karpenko, V.

    2003-01-01

    Roč. 103, č. 1 (2003), s. 25-33 ISSN 0301-4622 Grant - others:GA UK(CZ) No.220/2000/B-CH Institutional research plan: CEZ:AV0Z5011922; CEZ:MSM113100001; CEZ:MSM113200001; CEZ:MSM123100001 Keywords : orosomucoid * thermal stability * UV-spectroscopy Subject RIV: BO - Biophysics Impact factor: 1.728, year: 2003

  13. Correlation between Thermal Stability Map and Base Substitution Map of DNA from Related Bacteriophages

    Science.gov (United States)

    Husimi, Yuzuru; Shibata, Keizo

    1984-10-01

    The number density of substituted bases among related bacteriophages (fd, 1 and M13) is heterogeneous along the DNA strand although most base substitutions do not alter the coded amino acids. Local thermal stability of the double helical DNA is also heterogeneous. There is a negative correlation between these two maps. The same conclusion holds between less closely related phages, φX174 and G4.

  14. Thermal and photo-stability of the antioxidant potential of Spirulina platensis powder.

    Science.gov (United States)

    Colla, L M; Bertol, C D; Ferreira, D J; Bavaresco, J; Costa, J A V; Bertolin, T E

    2017-01-01

    This work aimed to evaluate the thermal and photo stability of the antioxidant potential (AP) of the Spirulina platensis biomass. Thermal stability was established at 25ºC, 40ºC and 50ºC for 60 days, in the dark, protected from light. Photo stability was evaluated using UV (15 W, λ = 265 nm) and fluorescent (20 W, 0.16 A, power factor FP > 0.5, 50/60 Hz, 60 lm/w, 1200 lm) light for 90 days in capsules, glass and Petri dishes, at room temperature. The AP of the biomass in these conditions was determined at intervals (every 7 and 30 days in the studies of thermal and photo stability, respectively) using the induction of the oxidation of a lipid system by heat and aeration. In this lipid system, the biomass submitted to degradation was used as an antioxidant. The kinetics of the reaction was determined by the Arrhenius method. Thermal degradation was found to follow zero order kinetics, whereas photo degradation followed first order kinetics. The AP decreased 50% after 50 days at 25°C. At 40°C and 50°C, the AP decreased more than 50% after 35 and 21 days of exposition, respectively. The decrease of the AP of Spirulina was more sensible to UV and fluorescence light. After 30 days of exposition, the AP decreased more than 50% in all storage conditions tested. The antioxidant potential of Spirulina platensis is easily degraded when the biomass is exposed to heat and light, indicating the need for care to be taken in its storage.

  15. Study on thermal decomposition of calix[4]arene and its application in thermal stability of polypropylene

    Energy Technology Data Exchange (ETDEWEB)

    Chennakesavulu, K., E-mail: chennanml@yahoo.com [National Metallurgical Laboratory Madras Centre, CSIR Complex, Taramani, Chennai 600113 (India); Basariya, M. Raviathul; Sreedevi, P.; Bhaskar Raju, G.; Prabhakar, S.; Rao, S. Subba [National Metallurgical Laboratory Madras Centre, CSIR Complex, Taramani, Chennai 600113 (India)

    2011-03-10

    Thermal decomposition kinetics of calix[4]arene (C4) was investigated using thermogravimetric analysis (TGA) and derivative of TG curve (DTG). TG experiments were carried out under static air atmosphere with nominal heating rates of 1.0, 2.5, 5.0 and 10.0 K/min. Model-fitting methods and model-free methods such as Friedman and Ozawa-Flynn-Wall methods were employed to evaluate the kinetic parameters such as activation energy (E{sub a}), exponential factor (ln A) and reaction order (n). To determine the antioxidant property of C4 the non-isothermal kinetics of polypropylene (PP) with C4 as additive was studied. The FTIR, ESR and {sup 13}C NMR CP-MAS techniques were used to propose the decomposition mechanism of C4 in the presence of PP.

  16. Thermal Conductivity and Water Vapor Stability of Ceramic HfO2-Based Coating Materials

    Science.gov (United States)

    Zhu, Dong-Ming; Fox, Dennis S.; Bansal, Narottam P.; Miller, Robert A.

    2004-01-01

    HfO2-Y2O3 and La2Zr2O7 are candidate thermal/environmental barrier coating materials for gas turbine ceramic matrix composite (CMC) combustor liner applications because of their relatively low thermal conductivity and high temperature capability. In this paper, thermal conductivity and high temperature phase stability of plasma-sprayed coatings and/or hot-pressed HfO2-5mol%Y2O3, HfO2-15mol%Y2O3 and La2Zr2O7 were evaluated at temperatures up to 1700 C using a steady-state laser heat-flux technique. Sintering behavior of the plasma-sprayed coatings was determined by monitoring the thermal conductivity increases during a 20-hour test period at various temperatures. Durability and failure mechanisms of the HfO2-Y2O3 and La2Zr2O7 coatings on mullite/SiC Hexoloy or CMC substrates were investigated at 1650 C under thermal gradient cyclic conditions. Coating design and testing issues for the 1650 C thermal/environmental barrier coating applications will also be discussed.

  17. Magnetic properties and thermal stability of MnBi/NdFeB hybrid bonded magnets

    International Nuclear Information System (INIS)

    Cao, S.; Yue, M.; Yang, Y. X.; Zhang, D. T.; Liu, W. Q.; Zhang, J. X.; Guo, Z. H.; Li, W.

    2011-01-01

    Magnetic properties and thermal stability were investigated for the MnBi/NdFeB (MnBi = 0, 20, 40, 60, 80, and 100 wt.%) bonded hybrid magnets prepared by spark plasma sintering (SPS) technique. Effect of MnBi content on the magnetic properties of the hybrid magnets was studied. With increasing MnBi content, the coercivity of the MnBi/NdFeB hybrid magnets increases rapidly, while the remanence and maximum energy product drops simultaneously. Thermal stability measurement on MnBi magnet, NdFeB magnet, and the hybrid magnet with 20 wt.% MnBi indicates that both the NdFeB magnet and the MnBi/NdFeB hybrid magnet have a negative temperature coefficient of coercivity, while the MnBi magnet has a positive one. The (BH) max of the MnBi/NdFeB magnet (MnBi = 20 wt.%) is 5.71 MGOe at 423 K, which is much higher than 3.67 MGOe of the NdFeB magnet, indicating a remarkable improvement of thermal stability.

  18. Lignin-based carbon fibers: Carbon nanotube decoration and superior thermal stability

    KAUST Repository

    Xu, Xuezhu

    2014-08-23

    Lignin-based carbon fibers (CFs) decorated with carbon nanotubes (CNTs) were synthesized and their structure, thermal stability and wettability were systematically studied. The carbon fiber precursors were produced by electrospinning lignin/polyacrylonitrile solutions. CFs were obtained by pyrolyzing the precursors and CNTs were subsequently grown on the CFs to eventually achieve a CF–CNT hybrid structure. The processes of pyrolysis and CNT growth were conducted in a tube furnace using different conditions and the properties of the resultant products were studied and compared. The CF–CNT hybrid structure produced at 850 °C using a palladium catalyst showed the highest thermal stability, i.e., 98.3% residual weight at 950 °C. A mechanism for such superior thermal stability was postulated based on the results from X-ray diffraction, Raman spectroscopy, scanning and transmission electron microscopy, and electron energy loss spectroscopy analyses. The dense CNT decoration was found to increase the hydrophobicity of the CFs.

  19. Thermal stability and ignition of a thermonuclear plasma with Kaye-Goldston scaling

    International Nuclear Information System (INIS)

    Johner, J.

    1987-01-01

    Stability of the ignition operation with respect to the pure thermal instability is investigated in the case of a temperature dependent non radiative energy confinement time (τ E ∝ 1/T γ ). The thermal stability of the operation with an external power independent of temperature is also studied. The stability criterion is put in the form of a (nτ E ,T) condition. The temperature for divergence leading to the minimum stable ignition is calculated in terms of γ as well as the corresponding external density power. Special attention is paid to the case of Kaye-Goldston scaling (γ=1.38). The necessary conditions for dimension and fusion power of an ignited tokamak with Kaye-Goldston scaling are derived taking into account explicit bremsstrahlung losses and plasma elongation. At the Murakami or β density limits, realistic dimensions can only be obtained with strong magnetic fields and elongations, but the corresponding high densities yield in turn impracticably large fusion powers. Dimension and density can then be calculated for a fixed power of the reactor (4000 MW(th)). Again, reasonable dimensions need high fields and elongations (B t ∼ 10T, x ∼ 1.5), but now Murakami and β limits are never exceeded. The external power necessary for thermal divergence can also be calculated in this case. It is found to be independent of elongation and decreasing with final ignition temperature. (author). 8 refs, 9 figs

  20. A spectroscopic and thermal stability study on the interaction between putrescine and bovine trypsin.

    Science.gov (United States)

    Momeni, Lida; Shareghi, Behzad; Saboury, Ali A; Farhadian, Sadegh; Reisi, Fateme

    2017-01-01

    The interaction of putrescine with bovine trypsin was investigated using steady state thermal stability, intrinsic fluorescence, UV-vis spectroscopy, far and near- UV circular dichroism and kinetic techniques, as well as molecular docking. The Stern-Volmer quenching constants for the trypsin- putrescine complex were calculated revealing that putrescine interacted with trypsin via the static fluorescence quenching. The enthalpy and entropy change values and the molecular docking technique revealed that hydrogen bonds and van der Waals forces play a major role in the binding process. Upon putrescine conjugation, the V max value and the k cat /K m values of the enzyme was increased. The results of UV absorbance, circular dichroism and fluorescence techniques demonstrated that the micro environmental changes in trypsin were induced by the binding of putrescine, leading to changes in its secondary structure. The thermal stability of trypsin- putrescine complex was enhanced more significantly, as compared to that of the native trypsin. The increased thermal stability of trypsin- putrescine complex might be due to the lower surface hydrophobicity and the higher hydrogen bond formation after putrescine modification, as reflected in the increase of UV absorbance and the quenching of fluorescence spectra. It was concluded that the binding of putrescine changed trypsin structure and function. Copyright © 2016 Elsevier B.V. All rights reserved.

  1. Polyethylene Glycol Based Graphene Aerogel Confined Phase Change Materials with High Thermal Stability.

    Science.gov (United States)

    Fu, Yang; Xiong, Weilai; Wang, Jianying; Li, Jinghua; Mei, Tao; Wang, Xianbao

    2018-05-01

    Polyethylene glycol (PEG) based graphene aerogel (GA) confined shaped-stabilized phase change materials (PCMs) are simply prepared by a one-step hydrothermal method. Three-dimensional GA inserted by PEG molecule chains, as a supporting material, obtained by reducing graphene oxide sheets, is used to keep their stabilized shape during a phase change process. The volume of GA is obviously expended after adding PEG, and only 9.8 wt% of GA make the composite achieve high energy efficiency without leakage during their phase change because of hydrogen bonding widely existing in the GA/PEG composites (GA-PCMs). The heat storage energy of GA-PCMs is 164.9 J/g, which is 90.2% of the phase change enthalpy of pure PEG. In addition, this composite inherits the natural thermal properties of graphene and thus shows enhanced thermal conductivity compared with pure PEG. This novel study provides an efficient way to fabricate shape-stabilized PCMs with a high content of PEG for thermal energy storage.

  2. Mechanical behaviour and thermal stability of multi-axially compressed copper

    Science.gov (United States)

    Padap, Aditya Kumar; Dwivedi, Ankit; Kumar, Narendra

    2018-01-01

    In the present study coarse grained (CG) annealed copper is subjected to multi-axial compression (MAC) process up to 9 passes to analyse its mechanical behaviour and thermal stability. The samples are characterized by optical microscopy to analyse microstructure evolution and grain size during MAC process. Mechanical properties like hardness and tensile strength have been evaluated by conducting the hardness and tensile test at ambient temperature. Microstructural examinations reveal the reduction in grain size with increase in number of passes which contributes to enhanced hardness and strength of copper. Tensile fractured specimens are examined under scanning electron microscope (SEM) to analyse the mode of failure with increasing number of MAC passes. Fractured micrographs reveal the ductile mode of failure in annealed and lower pass sample which is further converted to mixed mode (ductile and brittle) as the number of passes increased. Thermal stability of processed copper is also analysed by differential scanning calorimetry (DSC) analysis and results reveal reduction in thermal stability with increase in number of MAC passes. The evaluated properties of processed copper are correlated with microstructures.

  3. Physicochemical properties and thermal stability of quercetin hydrates in the solid state

    Energy Technology Data Exchange (ETDEWEB)

    Borghetti, G.S., E-mail: greicefarm@yahoo.com.br [Programa de Pos-Graduacao em Ciencias Farmaceuticas, Faculdade de Farmacia, Universidade Federal do Rio Grande do Sul, Av. Ipiranga 2752, CEP 90.610-000, Porto Alegre, RS (Brazil); Carini, J.P. [Programa de Pos-Graduacao em Ciencias Farmaceuticas, Faculdade de Farmacia, Universidade Federal do Rio Grande do Sul, Av. Ipiranga 2752, CEP 90.610-000, Porto Alegre, RS (Brazil); Honorato, S.B.; Ayala, A.P. [Departamento de Fisica, Universidade Federal do Ceara, Caixa Postal 6030, CEP 60.455-970, Fortaleza, CE (Brazil); Moreira, J.C.F. [Departamento de Bioquimica, Instituto de Ciencias Basicas da Saude, Universidade Federal do Rio Grande do Sul, Rua Ramiro Barcelos 2600, CEP 90035-003, Porto Alegre, RS (Brazil); Bassani, V.L. [Programa de Pos-Graduacao em Ciencias Farmaceuticas, Faculdade de Farmacia, Universidade Federal do Rio Grande do Sul, Av. Ipiranga 2752, CEP 90.610-000, Porto Alegre, RS (Brazil)

    2012-07-10

    Highlights: Black-Right-Pointing-Pointer Quercetin raw materials may present different degree of hydration. Black-Right-Pointing-Pointer Thermal stability of quercetin in the solid state depends on its degree of hydration. Black-Right-Pointing-Pointer Quercetin dehydrate is thermodynamically more stable than the other crystal forms. - Abstract: In the present work three samples of quercetin raw materials (QCTa, QCTb and QCTc), purchased from different Brazilian suppliers, were characterized employing scanning electron microscopy, Raman spectroscopy, simultaneous thermogravimetry and infrared spectroscopy, differential scanning calorimetry, and variable temperature-powder X-ray diffraction, in order to know their physicochemical properties, specially the thermal stability in solid state. The results demonstrated that the raw materials of quercetin analyzed present distinct crystalline structures, ascribed to the different degree of hydration of their crystal lattice. The thermal stability of these quercetin raw materials in the solid state was highly dependent on their degree of hydration, where QCTa (quercetin dihydrate) was thermodynamically more stable than the other two samples.

  4. Strategies To Increase the Thermal Stability of Truly Biomimetic Hydrogels: Combining Hydrophobicity and Directed Hydrogen Bonding

    Science.gov (United States)

    2017-01-01

    Enhancing the thermal stability of proteins is an important task for protein engineering. There are several ways to increase the thermal stability of proteins in biology, such as greater hydrophobic interactions, increased helical content, decreased occurrence of thermolabile residues, or stable hydrogen bonds. Here, we describe a well-defined polymer based on β-helical polyisocyanotripeptides (TriPIC) that uses biological approaches, including hydrogen bonding and hydrophobic interactions for its exceptional thermal stability in aqueous solutions. The multiple hydrogen bonding arrays along the polymer backbone shield the hydrophobic core from water. Variable temperature CD and FTIR studies indicate that, on heating, a better packed polymer conformation further stiffens the backbone. Driven by hydrophobic interactions, TriPIC solutions give fully reversible hydrogels that can withstand high temperatures (80 °C) for extended times. Cryo-scanning electron microscopy (cryo-SEM), small-angle X-ray scattering (SAXS), and thorough rheological analysis show that the hydrogel has a bundled architecture, which gives rise to strain stiffening effects on deformation of the gel, analogous to many biological hydrogels. PMID:29213150

  5. Strategies To Increase the Thermal Stability of Truly Biomimetic Hydrogels: Combining Hydrophobicity and Directed Hydrogen Bonding.

    Science.gov (United States)

    Yuan, Hongbo; Xu, Jialiang; van Dam, Eliane P; Giubertoni, Giulia; Rezus, Yves L A; Hammink, Roel; Bakker, Huib J; Zhan, Yong; Rowan, Alan E; Xing, Chengfen; Kouwer, Paul H J

    2017-11-28

    Enhancing the thermal stability of proteins is an important task for protein engineering. There are several ways to increase the thermal stability of proteins in biology, such as greater hydrophobic interactions, increased helical content, decreased occurrence of thermolabile residues, or stable hydrogen bonds. Here, we describe a well-defined polymer based on β-helical polyisocyanotripeptides (TriPIC) that uses biological approaches, including hydrogen bonding and hydrophobic interactions for its exceptional thermal stability in aqueous solutions. The multiple hydrogen bonding arrays along the polymer backbone shield the hydrophobic core from water. Variable temperature CD and FTIR studies indicate that, on heating, a better packed polymer conformation further stiffens the backbone. Driven by hydrophobic interactions, TriPIC solutions give fully reversible hydrogels that can withstand high temperatures (80 °C) for extended times. Cryo-scanning electron microscopy (cryo-SEM), small-angle X-ray scattering (SAXS), and thorough rheological analysis show that the hydrogel has a bundled architecture, which gives rise to strain stiffening effects on deformation of the gel, analogous to many biological hydrogels.

  6. Chemical stability, thermal behavior, and shelf life assessment of extruded modified double-base propellants

    Directory of Open Access Journals (Sweden)

    Sherif Elbasuney

    2018-02-01

    Full Text Available Double base propellant suffers from lack of chemical stability; this could result in self ignition during storing. Modified double base (MDB propellant based on stoichiometric binary mixture of oxidizer-metal fuel (Ammonium perchlorate/Aluminum, and energetic nitramines (HMX offered enhanced thrust as well as combustion characteristics. This study is devoted to evaluate the impact of such energetic additives on thermal behavior, chemical stability, and shelf life. Extruded MDB formulations were manufactured by extrusion process. Artificial aging at 80 °C for 28 days was conducted. Shelf life assessment was performed using Van't Hoff's equation. Quantification of evolved NOx gases with aging time was performed using quantitative stability tests. MDB formulation based on HMX demonstrated extended service life of 16 years compared with (AP/Al-MDB which demonstrated 9 years. This finding was ascribed to the reactivity of AP with nitroglycerin with the formation of perchloric acid. Thermal behavior of aged MDB, exhibited an increase in heat released with time; this was ascribed to the auto-catalytic thermal degradation during artificial aging. The increase in released heat by 31% was found to be equivalent to evolved NOx gases of 6.2 cm3/5 g and 2.5 cm3/1 g for Bergmann-Junk test, and Vacuum stability test respectively. This manuscript shaded the light on a novel approach to quantify evolved NOx gases to heat released with aging time. MDB based on HMX offered balanced ballistic performance, chemical stability, and service life.

  7. Improving the thermal behaviour of bricks by incorporating shape-stabilized phase change materials

    Science.gov (United States)

    Serrano, A.; Acosta, A.; Iglesias, I.; Rodríguez, J. F.; Carmona, M.

    2017-10-01

    The addition of a new shape-stabilized phase change material (ssPCM) in ceramic elements having large porosity has been carried out. In that way, a novel form-stable PCM based on bricks was developed. In order to study the incorporation of the thermoregulatory material in the composites, bricks with different porosities have been manufactured. In this work the ssPCM was synthesized using polyethylene glycol (PEG) as PCM and tetraethyl orthosilicate (TEOS) as supporter precursor by sol-gel method. The initial liquid product can be further turned into solid by neutralization procedures. ssPCM in its liquid form is adsorbed inside the porous brick by capillary action and it is further stabilized by controlling its gelation time, obtaining the new form-stable PCM. The adsorption curves, the long-term stability after 100 cycles of heating and cooling processes and the improved thermal energy storage capacities for the obtained samples have been studied. Different composites containing between 15 to 110 wt% of ssPCM respect to the initial dried mass of brick have been obtained, with thermal capacities within 8.94 to 28.80 kWh/m3. The Fick´s law was used to predict the adsorption curves and only one diffusion coefficient was required to predict the content of the ssPCM into the bricks, independently of their porosity. Besides, all the samples exhibited a high long-term thermal stability influenced by the additional stabilizer effect of the ceramic matrix.

  8. Effect of pH variation on the stability and structural properties of In(OH)3 nanoparticles synthesized by co-precipitation method

    International Nuclear Information System (INIS)

    Goh, Kian Wei; Wong, Yew Hoong; Johan, Mohd Rafie

    2016-01-01

    Indium hydroxide (In(OH) 3 ) nanoparticles were synthesized at various pH values (8-11) by co-precipitation method. Its properties were characterized by X-ray diffractometer, Fourier transform infrared spectroscopy, Raman spectroscopy and transmission electron microscope. The electrostatic stability of nanoparticles is carried out through zeta potential measurement. The crystallite size of nanoparticles calculated by Scherrer equation has similar trend with the values obtained from William-Hall plot. TEM images show that the particles size is within the range of 11.76-20.76 nm. The maximum zeta potential is 3.68 mV associated with the smallest particle size distribution of 92.6 nm occurred at pH 10. Our work clearly confirms the crystallite size, stability and the morphology of In(OH) 3 NPs are strongly depending on the pH of precursor solution. (orig.)

  9. Effect of pH variation on the stability and structural properties of In(OH){sub 3} nanoparticles synthesized by co-precipitation method

    Energy Technology Data Exchange (ETDEWEB)

    Goh, Kian Wei; Wong, Yew Hoong [University of Malaya, Department of Mechanical Engineering, Faculty of Engineering, Kuala Lumpur (Malaysia); Johan, Mohd Rafie [University of Malaya, Department of Mechanical Engineering, Faculty of Engineering, Kuala Lumpur (Malaysia); University of Malaya, Nanotechnology and Catalysis Research Centre, Kuala Lumpur (Malaysia)

    2016-10-15

    Indium hydroxide (In(OH){sub 3}) nanoparticles were synthesized at various pH values (8-11) by co-precipitation method. Its properties were characterized by X-ray diffractometer, Fourier transform infrared spectroscopy, Raman spectroscopy and transmission electron microscope. The electrostatic stability of nanoparticles is carried out through zeta potential measurement. The crystallite size of nanoparticles calculated by Scherrer equation has similar trend with the values obtained from William-Hall plot. TEM images show that the particles size is within the range of 11.76-20.76 nm. The maximum zeta potential is 3.68 mV associated with the smallest particle size distribution of 92.6 nm occurred at pH 10. Our work clearly confirms the crystallite size, stability and the morphology of In(OH){sub 3} NPs are strongly depending on the pH of precursor solution. (orig.)

  10. Influence of Tableting on the Conformation and Thermal Stability of Trypsin as a Model Protein

    DEFF Research Database (Denmark)

    Klukkert, Marten; Van De Weert, Marco; Fanø, Mathias

    2015-01-01

    The objective of this study was to investigate the influence of compaction on the conformation of trypsin, its transition temperature (Tm ) of unfolding, and its folding reversibility after thermal denaturation. Plain trypsin was compacted at 40-382 MPa. Pressure-induced changes in the trypsin...... was performed to determine the Tm as well as the folding reversibility after thermal denaturation of the reconstituted samples. It was found that compacted samples showed reduced activity accompanied by an altered secondary structure. Conformational changes that occur in the solid state were partially...... reversible upon tablet reconstitution. Aqueous-state IR spectroscopy combined with partial least squares was shown to be a powerful tool to follow irreversible structural changes and evaluate sample bioactivity. Besides its conformation, the thermal stability of trypsin was altered as a result of the applied...

  11. Differential scanning calorimetry thermal properties and oxidative stability indices of microwave heated extra virgin olive oils.

    Science.gov (United States)

    Chiavaro, Emma; Rodriguez-Estrada, Maria Teresa; Bendini, Alessandra; Rinaldi, Massimiliano; Cerretani, Lorenzo

    2011-01-30

    The use of differential scanning calorimetry (DSC) for assessing the deterioration effect of microwave heating on vegetable oils, and on olive oils in particular, has been partially explored in literature. The aim of this work was to evaluate the potential of DSC to discriminate among microwaved extra virgin olive oils (EvOo from different olive cultivar and origin), according to changes on thermal properties (upon cooling and heating) and traditional oxidative stability indices (peroxide, p-anisidine and TOTOX values). An elevated value of lipid oxidation was reached by the most unsaturated EvOo sample (9.5% of linoleic acid) at 6 min of microwave treatment. Free acidity significantly increased (0.42%) only for the oil sample with the highest water content (874 mg kg(-1) oil) at the longest time of treatment. Crystallisation enthalpies significantly decreased and the major exothermic peak shifted towards lower temperature, leading to enlargement of the transition range in all samples due to the formation of weak and mixed crystals among triacylglycerols and lipid degradation products. On the contrary, thermal properties upon heating appeared to similarly vary among samples. The analysis of DSC thermal properties upon cooling seemed to clearly discriminate among different EvOo samples after microwaving. The relation between changes of thermal properties and oxidation parameters should be further studied using additional oxidative stability indices on a larger set of oil samples, due to the complexity of EvOo composition. 2010 Society of Chemical Industry.

  12. Performance and Thermal Stability of a Polyaromatic Hydrocarbon in a Simulated Concentrating Solar Power Loop

    Directory of Open Access Journals (Sweden)

    Joanna McFarlane

    2014-01-01

    Full Text Available Because polyaromatic hydrocarbons show high thermal stability, an example of these compounds, phenylnaphthalene, was tested for solar thermal-power applications. Although static thermal tests showed promising results for 1-phenylnaphthalene, loop testing at temperatures to 450 ℃ indicated that the fluid isomerized and degraded at a slow rate. In a loop with a temperature high enough to drive the isomerization, the higher melting point byproducts tended to condense onto cooler surfaces. This would indicate that the internal channels of cooler components of trough solar electric generating systems, such as the waste heat rejection exchanger, may become coated or clogged affecting loop performance. Thus, pure 1-phenylnaphthalene, without addition of stabilizers, does not appear to be a fluid that would have a sufficiently long lifetime (years to decades to be used in a loop at temperatures significantly greater than the current 400 ℃ maximum for organic fluids. Similar degradation pathways may occur with other organic materials. The performance of a concentrating solar loop using high temperature fluids was modeled based on the National Renewable Laboratory Solar Advisory Model. It was determined that a solar-to-electricity efficiency of up to 30% and a capacity factor of 60% could be achieved using a high efficiency collector and 12 h thermal energy storage when run at a field outlet temperature of 550 ℃.

  13. Nonlinear thermal stability of geometrically imperfect shape memory alloy hybrid laminated composite plates

    Science.gov (United States)

    Asadi, Hamed; Eynbeygi, Mehdi; Wang, Quan

    2014-07-01

    The instability of geometrically imperfect shape memory alloy (SMA) fibers reinforced with hybrid laminated composite (SMAHC) plates and subjected to a uniform thermal loading is analytically investigated. The material properties of the SMAHC plates are assumed to be functions of temperature. Nonlinear equations of the plates’ thermal stability are derived based on a higher order shear deformation theory incorporating von Karman geometrical nonlinearity via stationary potential energy. The structural recovery stress, which is generated by martensitic phase transformation of the prestrained SMA fibers, is calculated based on the one-dimensional thermodynamic constitutive model by Brinson. Adopting the Galerkin procedure, the governing nonlinear partial differential equations are converted into a set of nonlinear algebraic equations, in which systems of equations are solved by introducing an analytical approach. Closed-form formulations are presented to determine the load-deflection path and critical buckling temperature of the plate. Based on the developed closed-form solutions, ample numerical results are presented to provide an insight into the effects of the volume fraction, prestrain, location and orientation of the SMA fibers, composite plate geometry, geometrical imperfection and temperature dependence on the stability of the SMAHC plates. It is shown that a proper application of SMA fibers results in a considerable delay of the thermal bifurcation and controllable thermal post-buckling deflection of the SMAHC plate.

  14. Thermal stability of antiparasitic macrocyclic lactones milk residues during industrial processing.

    Science.gov (United States)

    Imperiale, F A; Farias, C; Pis, A; Sallovitz, J M; Lifschitz, A; Lanusse, C

    2009-01-01

    The chemical stability of residues of different antiparasitic macrocyclic lactone compounds in milk subjected to thermal treatment was assessed. Concentrations of ivermectin (IVM), moxidectin (MXD) and eprinomectin (EPM) in sheep milk, equivalent to those measured in vivo in milk excretion studies, were subjected to 65 degrees C over 30 min or to 75 degrees C for 15 s. Residue concentrations of IVM, MXD and EPM in milk were measured by high-performance liquid chromatography (HPLC) (fluorescence detection) before and after heat treatment of the drug-fortified milk samples. No evidence of chemical loss was obtained in either of the thermal treatments under evaluation. The stability of the parent compounds in milk was evidenced by the lack of bioconversion products (metabolites) after both thermal treatments. Only very minor changes on drug concentrations were observed at the end of the treatments, which fell within the limits of the variation of the validated analytical method. In conclusion, residue concentrations of macrocyclic lactones are unaffected by industrial-simulated milk thermal procedures. Based on the reported findings, it can be postulated that residue concentrations of IVM, MXD and EPM measured in raw sheep milk may be used to estimate consumer exposure and dietary intake for these veterinary drugs.

  15. Heat inactivation kinetics of Hypocrea orientalis β-glucosidase with enhanced thermal stability by glucose.

    Science.gov (United States)

    Xu, Xin-Qi; Shi, Yan; Wu, Xiao-Bing; Zhan, Xi-Lan; Zhou, Han-Tao; Chen, Qing-Xi

    2015-11-01

    Thermal inactivation kinetics of Hypocrea orientalis β-glucosidase and effect of glucose on thermostability of the enzyme have been determined in this paper. Kinetic studies showed that the thermal inactivation was irreversible and first-order reaction. The microscopic rate constants for inactivation of free enzyme and substrate-enzyme complex were both determined, which suggested that substrates can protect β-glucosidase against thermal deactivation effectively. On the other hand, glucose was found to protect β-glucosidase from heat inactivation to remain almost whole activity below 70°C at 20mM concentration, whereas the apparent inactivation rate of BG decreased to be 0.3×10(-3)s(-1) in the presence of 5mM glucose, smaller than that of sugar-free enzyme (1.91×10(-3)s(-1)). The intrinsic fluorescence spectra results showed that glucose also had stabilizing effect on the conformation of BG against thermal denaturation. Docking simulation depicted the interaction mode between glucose and active residues of the enzyme to produce stabilizing effect. Copyright © 2015 Elsevier B.V. All rights reserved.

  16. Thermal Stability of RNA Structures with Bulky Cations in Mixed Aqueous Solutions.

    Science.gov (United States)

    Nakano, Shu-Ichi; Tanino, Yuichi; Hirayama, Hidenobu; Sugimoto, Naoki

    2016-10-04

    Bulky cations are used to develop nucleic-acid-based technologies for medical and technological applications in which nucleic acids function under nonaqueous conditions. In this study, the thermal stability of RNA structures was measured in the presence of various bulky cations in aqueous mixtures with organic solvents or polymer additives. The stability of oligonucleotide, transfer RNA, and polynucleotide structures was decreased in the presence of salts of tetrabutylammonium and tetrapentylammonium ions, and the stability and salt concentration dependences were dependent on cation sizes. The degree to which stability was dependent on salt concentration was correlated with reciprocals of the dielectric constants of mixed solutions, regardless of interactions between the cosolutes and RNA. Our results show that organic solvents affect the strength of electrostatic interactions between RNA and cations. Analysis of ion binding to RNA indicated greater enhancement of cation binding to RNA single strands than to duplexes in media with low dielectric constants. Furthermore, background bulky ions changed the dependence of RNA duplex stability on the concentration of metal ion salts. These unique properties of large tetraalkylammonium ions are useful for controlling the stability of RNA structures and its sensitivity to metal ion salts. Copyright © 2016 Biophysical Society. Published by Elsevier Inc. All rights reserved.

  17. Multiple sample setup for testing the hydrothermal stability of adsorbents in thermal energy storage applications

    International Nuclear Information System (INIS)

    Fischer, Fabian; Laevemann, Eberhard

    2015-01-01

    Thermal energy storage based on adsorption and desorption of water on an adsorbent can achieve high energy storage densities. Many adsorbents lose adsorption capacity when operated under unfavourable hydrothermal conditions during adsorption and desorption. The stability of an adsorbent against stressing hydrothermal conditions is a key issue for its usability in adsorption thermal energy storage. We built an experimental setup that simultaneously controls the hydrothermal conditions of 16 samples arranged in a matrix of four temperatures and four water vapour pressures. This setup allows the testing of potential adsorbents between temperatures of 50 °C and 350 °C and water vapour pressures of up to 32 kPa. A measurement procedure that allows the detection of the hydrothermal stability of an adsorbent after defined time spans has been designed. We verified the functionality of the multiple sample measurements with a microporous adsorbent, a zeolite NaMSX. The hydrothermal stability of this zeolite is tested by water uptake measurements. A standard deviation lower than 1% of the 16 samples for detecting the hydrothermal stability enables setting different conditions in each sample cell. Further, we compared the water uptake measurements by measuring their adsorption isotherms with the volumetric device BELSORP Aqua 3 from Bel Japan. (paper)

  18. Glycerol, trehalose and glycerol–trehalose mixture effects on thermal stabilization of OCT

    Energy Technology Data Exchange (ETDEWEB)

    Barreca, D., E-mail: dbarreca@unime.it [Dipartimento di Scienze Chimiche, Università di Messina, Viale F. Stagno d’Alcontres 31, 98166 Messina (Italy); Laganà, G. [Dipartimento di Scienze Chimiche, Università di Messina, Viale F. Stagno d’Alcontres 31, 98166 Messina (Italy); Magazù, S.; Migliardo, F. [Dipartimento di Fisica, Università di Messina, Viale F. Stagno d’Alcontres 31, 98166 Messina (Italy); Bellocco, E. [Dipartimento di Scienze Chimiche, Università di Messina, Viale F. Stagno d’Alcontres 31, 98166 Messina (Italy)

    2013-10-16

    Highlights: • Trehalose influences both enzymatic activity and conformational changes of enzyme. • The results obtained by INS and QENS show a switching-off of the fast dynamics at very low glycerol content. • The diffusive dynamics is slowing down at very low glycerol concentration. • The mixtures of trehalose/glycerol lose the thermal stabilizing effects of pure compounds. - Abstract: The stabilization effects of trehalose, glycerol and their mixtures on ornithine carbamoyltransferase catalytic activity has been studied as a function of temperature by complementary techniques. The obtained results show that the kinematic viscosities of trehalose (1.0 M) and protein mixture are higher than the one of glycerol plus protein. Changing the trehalose/glycerol ratio, we notice a decrease of the kinematic viscosity values at almost all the analyzed ratio. In particular, the solution composed of 95% trehalose-5% glycerol shows a peculiar behavior. Moreover the trehalose (1.0 M) solution shows the higher OCT thermal stabilization at 343 K, while all the other solutions show minor effects. The smallest stabilizing effect is revealed for the solution that shows the maximum kinematic viscosity. These results support Inelastic Neutron Scattering (INS) and Quasi Elastic Neutron Scattering (QENS) findings, which pointed out a slowing down of the relaxation and diffusive dynamics in some investigated samples.

  19. Thermal stability analysis of eccentrically stiffened Sigmoid-FGM plate with metal–ceramic–metal layers based on FSDT

    Directory of Open Access Journals (Sweden)

    Pham Hong Cong

    2016-12-01

    Full Text Available This paper researches the thermal stability of eccentrically stiffened plates made of functionally graded materials (FGM with metal–ceramic–metal layers subjected to thermal load. The equilibrium and compatibility equations for the plates are derived by using the first-order shear deformation theory of plates, taking into account both the geometrical nonlinearity in the von Karman sense and initial geometrical imperfections with Pasternak type elastic foundations. By applying Galerkin method and using stress function, effects of material and geometrical properties, elastic foundations, temperature-dependent material properties, and stiffeners on the thermal stability of the eccentrically stiffened S-FGM plates in thermal environment are analyzed and discussed.

  20. Effects of high hydrostatic pressure or hydrophobic modification on thermal stability of xanthine oxidase.

    Science.gov (United States)

    Halalipour, Ali; Duff, Michael R; Howell, Elizabeth E; Reyes-De-Corcuera, José I

    2017-08-01

    The effect of high hydrostatic pressure (HHP) on the kinetics of thermal inactivation of xanthine oxidase (XOx) from bovine milk was studied. Inactivation of XOx followed pseudo-first-order kinetics at 0.1-300MPa and 55.0-70.0°C. High pressure up to at least 300MPa stabilized XOx at all the studied temperatures. The highest stabilization effect of HHP on XOx was at 200-300MPa at 55.0 and 58.6°C, and at 250-300MPa at 62.3-70.0°C. The stability of XOx increased 9.5 times at 300MPa and 70.0°C compared to atmospheric pressure at the same temperature. The activation energy of inactivation of XOx decreased with pressure and was 1.9 times less at 300MPa (97.0±8.2kJmol -1 ) than at 0.1MPa (181.7±12.1kJmol -1 ). High pressure decreased the dependence of the rate constant of inactivation to temperature effects compared to atmospheric pressure. The stabilizing effect of HHP on XOx was highest at 70.0°C where the activation volume of inactivation of XOx was 28.9±2.9cm 3 mol -1 . A second approach to try to increase XOx stability involved hydrophobic modification using aniline or benzoate. However, the thermal stability of XOx remained unaffected after 8-14 modifications of carboxyl side groups per XOx monomer with aniline, or 12-17 modifications of amino side groups per XOx monomer with benzoate. Copyright © 2017 Elsevier Inc. All rights reserved.

  1. Stability analysis of BWR nuclear-coupled thermal-hyraulics using a simple model

    Energy Technology Data Exchange (ETDEWEB)

    Karve, A.A.; Rizwan-uddin; Dorning, J.J. [Univ. of Virginia, Charlottesville, VA (United States)

    1995-09-01

    A simple mathematical model is developed to describe the dynamics of the nuclear-coupled thermal-hydraulics in a boiling water reactor (BWR) core. The model, which incorporates the essential features of neutron kinetics, and single-phase and two-phase thermal-hydraulics, leads to simple dynamical system comprised of a set of nonlinear ordinary differential equations (ODEs). The stability boundary is determined and plotted in the inlet-subcooling-number (enthalpy)/external-reactivity operating parameter plane. The eigenvalues of the Jacobian matrix of the dynamical system also are calculated at various steady-states (fixed points); the results are consistent with those of the direct stability analysis and indicate that a Hopf bifurcation occurs as the stability boundary in the operating parameter plane is crossed. Numerical simulations of the time-dependent, nonlinear ODEs are carried out for selected points in the operating parameter plane to obtain the actual damped and growing oscillations in the neutron number density, the channel inlet flow velocity, and the other phase variables. These indicate that the Hopf bifurcation is subcritical, hence, density wave oscillations with growing amplitude could result from a finite perturbation of the system even where the steady-state is stable. The power-flow map, frequently used by reactor operators during start-up and shut-down operation of a BWR, is mapped to the inlet-subcooling-number/neutron-density (operating-parameter/phase-variable) plane, and then related to the stability boundaries for different fixed inlet velocities corresponding to selected points on the flow-control line. The stability boundaries for different fixed inlet subcooling numbers corresponding to those selected points, are plotted in the neutron-density/inlet-velocity phase variable plane and then the points on the flow-control line are related to their respective stability boundaries in this plane.

  2. Protein thermal stability enhancement by designing salt bridges: a combined computational and experimental study.

    Directory of Open Access Journals (Sweden)

    Chi-Wen Lee

    Full Text Available Protein thermal stability is an important factor considered in medical and industrial applications. Many structural characteristics related to protein thermal stability have been elucidated, and increasing salt bridges is considered as one of the most efficient strategies to increase protein thermal stability. However, the accurate simulation of salt bridges remains difficult. In this study, a novel method for salt-bridge design was proposed based on the statistical analysis of 10,556 surface salt bridges on 6,493 X-ray protein structures. These salt bridges were first categorized based on pairing residues, secondary structure locations, and Cα-Cα distances. Pairing preferences generalized from statistical analysis were used to construct a salt-bridge pair index and utilized in a weighted electrostatic attraction model to find the effective pairings for designing salt bridges. The model was also coupled with B-factor, weighted contact number, relative solvent accessibility, and conservation prescreening to determine the residues appropriate for the thermal adaptive design of salt bridges. According to our method, eight putative salt-bridges were designed on a mesophilic β-glucosidase and 24 variants were constructed to verify the predictions. Six putative salt-bridges leaded to the increase of the enzyme thermal stability. A significant increase in melting temperature of 8.8, 4.8, 3.7, 1.3, 1.2, and 0.7°C of the putative salt-bridges N437K-D49, E96R-D28, E96K-D28, S440K-E70, T231K-D388, and Q277E-D282 was detected, respectively. Reversing the polarity of T231K-D388 to T231D-D388K resulted in a further increase in melting temperatures by 3.6°C, which may be caused by the transformation of an intra-subunit electrostatic interaction into an inter-subunit one depending on the local environment. The combination of the thermostable variants (N437K, E96R, T231D and D388K generated a melting temperature increase of 15.7°C. Thus, this study

  3. The Effect of Thermal Cycling Treatments on the Thermal Stability and Mechanical Properties of a Ti-Based Bulk Metallic Glass Composite

    Directory of Open Access Journals (Sweden)

    Fan Bu

    2016-11-01

    Full Text Available The effect of thermal cycling treatments on the thermal stability and mechanical properties of a Ti48Zr20Nb12Cu5Be15 bulk metallic glass composite (BMGC has been investigated. Results show that moderate thermal cycles in a temperature range of −196 °C (cryogenic temperature, CT to 25 °C (room temperature, RT or annealing time at CT has not induced obvious changes of thermal stability and then it decreases slightly over critical thermal parameters. In addition, the dendritic second phases with a bcc structure are homogeneously embedded in the amorphous matrix; no visible changes are detected, which shows structural stability. Excellent mechanical properties as high as 1599 MPa yield strength and 34% plastic strain are obtained, and the yield strength and elastic modulus also increase gradually. The effect on the stability is analyzed quantitatively by crystallization kinetics and plastic-flow models, and indicates that the reduction of structural relaxation enthalpy, which is related to the degradation of spatial heterogeneity, reduces thermal stability but does not imperatively deteriorate the plasticity.

  4. Effect of thermal cycling and disinfection on colour stability of denture base acrylic resin.

    Science.gov (United States)

    Goiato, Marcelo C; Dos Santos, Daniela M; Baptista, Gabriella T; Moreno, Amália; Andreotti, Agda M; Bannwart, Lisiane C; Dekon, Stefan F C

    2013-12-01

    The purpose of this study was to investigate the effect of thermal cycling and disinfection on the colour change of denture base acrylic resin. Four different brands of acrylic resins were evaluated (Onda Cryl, QC 20, Classico and Lucitone). All brands were divided into four groups (n = 7) determined according to the disinfection procedure (microwave, Efferdent, 4% chlorhexidine or 1% hypochlorite). The treatments were conducted three times a week for 60 days. All specimens were thermal cycled between 5 and 55°C with 30-s dwell times for 1000 cycles before and after disinfection. The specimens' colour was measured with a spectrophotometer using the CIE L*a*b* system. The evaluations were conducted at baseline (B), after first thermal cycling (T1 ), after disinfection (D) and after second thermal cycling (T2 ). Colour differences (ΔE) were calculated between T1 and B (T1 B), D and B (DB), and T2 and B (T2 B) time-points.   The samples submitted to disinfection by microwave and Efferdent exhibited the highest values of colour change. There were significant differences on colour change between the time-points, except for the Lucitone acrylic resin. The thermal cycling and disinfection procedures significantly affected the colour stability of the samples. However, all values obtained for the acrylic resins are within acceptable clinical parameters. © 2012 John Wiley & Sons A/S and The Gerodontology Society. Published by John Wiley & Sons Ltd.

  5. Impact of impurity content on the sintering resistance and phase stability of dysprosia- and yttria-stabilized zirconia thermal barrier coatings

    Czech Academy of Sciences Publication Activity Database

    Curry, N.; Janikowski, W.; Pala, Zdeněk; Vilémová, Monika; Markocsan, N.

    2014-01-01

    Roč. 23, 1-2 (2014), s. 160-169 ISSN 1059-9630. [International Thermal Spray Conference (ITSC2013). Busan, 13.05.2013-15.05.2013] Institutional support: RVO:61389021 Keywords : atmospheric plasma spray ( APS ) * thermal and phase stability of coatings * thermal barrier coatings (TBCs) * thermal conductivity * zirconia Subject RIV: JH - Ceramics, Fire-Resistant Materials and Glass Impact factor: 1.344, year: 2014 http://link.springer.com/article/10.1007%2Fs11666-013-0014-9/fulltext.html

  6. Stability of poly(N-isopropylacrylamide-co-acrylic acid polymer microgels under various conditions of temperature, pH and salt concentration

    Directory of Open Access Journals (Sweden)

    Zahoor H. Farooqi

    2017-03-01

    Full Text Available This research article describes the colloidal stability of poly(N-isopropylacrylamide-co-acrylic acid [P(NIPAM-co-AAc] polymer microgels with different acrylic acid contents in aqueous medium under various conditions of temperature, pH and sodium chloride concentrations. Three samples of multi-responsive P(NIPAM-co-AAc polymer microgels were synthesized using different amounts of acrylic acid by free radical emulsion polymerization. Dynamic laser light scattering was used to investigate the responsive behavior and stability of the prepared microgels under various conditions of pH, temperature and ionic strength. The microgels were found to be stable at all pH values above the pKa value of acrylic acid moiety in the temperature range from 15 to 60 °C in the presence and absence of sodium chloride. Increase in temperature, salt concentration and decrease in pH causes aggregation and decreases the stability of microgels due to the decrease in hydrophilicity.

  7. Improving the Mechanical Performance and Thermal Stability of a PVA-Clay Nanocomposite by Electron Beam Irradiation

    Science.gov (United States)

    Shokuhi Rad, A.; Ebrahimi, D.

    2017-07-01

    The effects of electron beam irradiation and presence of clay on the mechanical properties and thermal stability of montmorillonite clay-modified polyvinyl alcohol nanocomposites were studied. By using the X-ray diffraction (XRD) and transmission electron microscopy (TEM), the microstructure of the nanocomposites was investigated. The results obtained from TEM and XRD tests showed that montmorillonite clay nanoparticles were located in the polyvinyl alcohol phase. The XRD analysis confirmed the formation of an exfoliated structure in nanocomposites samples. Increasing the amount of clay to 20 wt.% increased the tensile strength and modulus of the nanocomposite. Irradiation up to an absorbed dose of 100 kGy increased its mechanical properties and thermal stability, but at higher irradiation levels, the mechanical strength and thermal stability declined. The sample with 20 wt.% of the nanofiller, exposed to 100 kGy, showed the highest mechanical strength and thermal stability.

  8. Thermal stability of formulations of PVC irradiated with γ of 60

    International Nuclear Information System (INIS)

    Martinez P, M.E.; Carrasco A, H.; Castaneda F, A.; Benavides C, R.; Garcia R, S.P.

    2004-01-01

    The industry of cables and wires frequently use cable isolations with base of formulations of PVC, in those that stabilizer has usually been used with the help of heavy metals, as the lead, which is toxic. To solve the problem, from the 2002 one has come studying in combined form in the National Institute of Nuclear Research ININ and the Center of Investigation in Applied Chemistry CIQA, the modifications induced by the radiation in formulations with the help of vinyl poly chloride PVC. In these formulations, prepared with cross linking agent, plastifying industrial grade, stuff and non toxic stabilizers of calcium estearate and zinc industrial grade, it is sought to replace the stabilizer of Pb. For this were irradiated it test tubes of PVC with gamma radiation of cobalt 60 to three different dose in atmospheres of air and argon. Later it was determined their thermal stability at different times of heating and it was measured the Young modulus by means of thermo mechanical analysis. Those results obtained together with other techniques of characterization suggest that the irradiated proposed formulation can substitute the one stabilized with lead. (Author)

  9. Synthesis of a Novel Polyethoxysilsesquiazane and Thermal Conversion into Ternary Silicon Oxynitride Ceramics with Enhanced Thermal Stability.

    Science.gov (United States)

    Iwase, Yoshiaki; Horie, Yoji; Daiko, Yusuke; Honda, Sawao; Iwamoto, Yuji

    2017-12-05

    A novel polyethoxysilsesquiazane ([EtOSi(NH) 1.5 ] n , EtOSZ) was synthesized by ammonolysis at -78 °C of ethoxytrichlorosilane (EtOSiCl₃), which was isolated by distillation as a reaction product of SiCl₄ and EtOH. Attenuated total reflection-infra red (ATR-IR), 13 C-, and 29 Si-nuclear magnetic resonance (NMR) spectroscopic analyses of the ammonolysis product resulted in the detection of Si-NH-Si linkage and EtO group. The simultaneous thermogravimetric and mass spectrometry analyses of the EtOSZ under helium revealed cleavage of oxygen-carbon bond of the EtO group to evolve ethylene as a main gaseous species formed in-situ, which lead to the formation at 800 °C of quaternary amorphous Si-C-N with an extremely low carbon content (1.1 wt %) when compared to the theoretical EtOSZ (25.1 wt %). Subsequent heat treatment up to 1400 °C in N₂ lead to the formation of X-ray amorphous ternary Si-O-N. Further heating to 1600 °C in N₂ promoted crystallization and phase partitioning to afford Si₂N₂O nanocrystallites identified by the XRD and TEM analyses. The thermal stability up to 1400 °C of the amorphous state achieved for the ternary Si-O-N was further studied by chemical composition analysis, as well as X-ray photoelectron spectroscopy (XPS) and 29 Si-NMR spectroscopic analyses, and the results were discussed aiming to develop a novel polymeric precursor for ternary amorphous Si-O-N ceramics with an enhanced thermal stability.

  10. Synthesis of a Novel Polyethoxysilsesquiazane and Thermal Conversion into Ternary Silicon Oxynitride Ceramics with Enhanced Thermal Stability

    Directory of Open Access Journals (Sweden)

    Yoshiaki Iwase

    2017-12-01

    Full Text Available A novel polyethoxysilsesquiazane ([EtOSi(NH1.5]n, EtOSZ was synthesized by ammonolysis at −78 °C of ethoxytrichlorosilane (EtOSiCl3, which was isolated by distillation as a reaction product of SiCl4 and EtOH. Attenuated total reflection-infra red (ATR-IR, 13C-, and 29Si-nuclear magnetic resonance (NMR spectroscopic analyses of the ammonolysis product resulted in the detection of Si–NH–Si linkage and EtO group. The simultaneous thermogravimetric and mass spectrometry analyses of the EtOSZ under helium revealed cleavage of oxygen-carbon bond of the EtO group to evolve ethylene as a main gaseous species formed in-situ, which lead to the formation at 800 °C of quaternary amorphous Si–C–N with an extremely low carbon content (1.1 wt % when compared to the theoretical EtOSZ (25.1 wt %. Subsequent heat treatment up to 1400 °C in N2 lead to the formation of X-ray amorphous ternary Si–O–N. Further heating to 1600 °C in N2 promoted crystallization and phase partitioning to afford Si2N2O nanocrystallites identified by the XRD and TEM analyses. The thermal stability up to 1400 °C of the amorphous state achieved for the ternary Si-O-N was further studied by chemical composition analysis, as well as X-ray photoelectron spectroscopy (XPS and 29Si-NMR spectroscopic analyses, and the results were discussed aiming to develop a novel polymeric precursor for ternary amorphous Si–O–N ceramics with an enhanced thermal stability.

  11. Thermal and hydrothermal stability of selected polymers in a nuclear reactor environment

    Science.gov (United States)

    Kim, Jinho

    The focus of this study is the development and understanding of polymer based burnable poison rod assemblies (BPRAs) in pressurized water reactors (PWRs). This material substitution reduces the water displacement penalty at the end of cycle (EOC) currently found with the B4C/Al 2O3 BPRAs that displace moderator water in PWRs. This gives rise to a longer fuel cycle due to the extra moderation from hydrogen in polymer structures. Finding synthetic polymers that endure a severe nuclear reactor circumstance is a challenge. Aside from the proper thermal stability at the range of 350--600°C in the core for a single cycle, the hydrothermal stability at near-critical water condition (350°C, 20.7MPa) is required to maintain the safe and controlled nuclear reaction because a danger comes if water might possibly penetrate inside the burnable poison rod by the failure of zircaloy cladding. There are two approaches to obtain a boron source (burnable position material) in hydrogen containing polymers. One is to utilize the boron source directly by synthesizing boron-containing polymers. A second approach is to find commercial polymers that have an appropriate thermal, hydrothermal, radiational stability and high hydrogen content; and then add an inorganic boron source such as B4C to form a composite material. Poly (diacetylene-siloxane-carborane)s and other silicon based precursor polymers were introduced to observe their thermal and hydrothermal stability. However, we found that the degradation of Si-O-Si, which was presented in the polymer, was an unfavorable disadvantage under near-critical water (350°C, 20.7MPa) even though they formed dense network structures. In addition, the Si-O bond is quite sensitive to variety of reagents, including base and acid. Therefore, the degradation rate might be accelerated by high H+ and OH- ion concentrations at the near-critical water condition. For the second approach, a number of candidate matrix polymers were screened for new

  12. Thermal stability, thermal expansion and grain-growth in exchange-coupled Fe-Pt-Ag-B bulk nanocomposite magnets

    International Nuclear Information System (INIS)

    Nicula, R.; Crisan, O.; Crisan, A.D.; Mercioniu, I.; Stir, M.; Vasiliu, F.

    2015-01-01

    Highlights: • Formation of the L10 FePt hard-magnetic phase (>90%) directly in the as-cast state. • Specific alternating hard/soft nanostructure is stable to 600 °C without grain growth. • Anisotropic and non-linear thermal expansion effects. • The FePtAgB alloy behaves like a single magnetic phase (full exchange coupling). - Abstract: Rare-earth free (RE-free) exchange coupling nanocomposite magnets are intensively studied nowadays due to their potential use in applications demanding stable high-temperature operation and corrosion resistance. In this respect, the FePt alloy system is one of the most actively addressed potential permanent magnet solutions. In FePt alloys, promising magnetic features arise from the co-existence of hard magnetic L1 0 FePt and soft magnetic L1 2 Fe 3 Pt phases emerged from the same metastable precursor. The present work deals with an in-situ temperature-resolved synchrotron radiation study of the thermal stability, thermal expansion and microstructure evolution in exchange-coupled FePtAgB alloys. The as-cast microstructural state as well as the optimized magnetic behavior are given as reference and correlated to the observed microstructural evolution with temperature. The melt-spun Fe 48 Pt 28 Ag 6 B 18 alloy ribbons were examined in situ by synchrotron X-ray powder diffraction from ambient temperature up to 600 °C. The FePt-Fe 3 Pt exchange-coupled microstructure achieved by rapid solidification is not significantly altered during the high temperature exposure. The thermal expansion of the FePt L1 0 unit cell has been found to be strongly anisotropic, being essentially an in-plane expansion which may be seen as an anisotropic invar effect. For the FePt L1 0 phase, a significant deviation from linear thermal expansion is observed at the Curie temperature T C = 477 °C. This non-linear behavior above T C is tentatively linked to a diffusion/segregation mechanism of Ag. The promising hard magnetic properties as well as the

  13. Thermal stability, thermal expansion and grain-growth in exchange-coupled Fe-Pt-Ag-B bulk nanocomposite magnets

    Energy Technology Data Exchange (ETDEWEB)

    Nicula, R., E-mail: radu.nicula@empa.ch [Empa, Swiss Federal Laboratories for Materials Science and Technology, Advanced Materials Processing, Feuerwerkerstr. 39, CH-3602 Thun (Switzerland); Crisan, O.; Crisan, A.D.; Mercioniu, I. [National Institute for Materials Physics, P.O. Box MG-7, 077125 Bucharest-Magurele (Romania); Stir, M. [University of Berne, Department of Chemistry and Biochemistry, Freiestrasse 3, CH-3012 Berne (Switzerland); Vasiliu, F. [National Institute for Materials Physics, P.O. Box MG-7, 077125 Bucharest-Magurele (Romania)

    2015-02-15

    Highlights: • Formation of the L10 FePt hard-magnetic phase (>90%) directly in the as-cast state. • Specific alternating hard/soft nanostructure is stable to 600 °C without grain growth. • Anisotropic and non-linear thermal expansion effects. • The FePtAgB alloy behaves like a single magnetic phase (full exchange coupling). - Abstract: Rare-earth free (RE-free) exchange coupling nanocomposite magnets are intensively studied nowadays due to their potential use in applications demanding stable high-temperature operation and corrosion resistance. In this respect, the FePt alloy system is one of the most actively addressed potential permanent magnet solutions. In FePt alloys, promising magnetic features arise from the co-existence of hard magnetic L1{sub 0} FePt and soft magnetic L1{sub 2} Fe{sub 3}Pt phases emerged from the same metastable precursor. The present work deals with an in-situ temperature-resolved synchrotron radiation study of the thermal stability, thermal expansion and microstructure evolution in exchange-coupled FePtAgB alloys. The as-cast microstructural state as well as the optimized magnetic behavior are given as reference and correlated to the observed microstructural evolution with temperature. The melt-spun Fe{sub 48}Pt{sub 28}Ag{sub 6}B{sub 18} alloy ribbons were examined in situ by synchrotron X-ray powder diffraction from ambient temperature up to 600 °C. The FePt-Fe{sub 3}Pt exchange-coupled microstructure achieved by rapid solidification is not significantly altered during the high temperature exposure. The thermal expansion of the FePt L1{sub 0} unit cell has been found to be strongly anisotropic, being essentially an in-plane expansion which may be seen as an anisotropic invar effect. For the FePt L1{sub 0} phase, a significant deviation from linear thermal expansion is observed at the Curie temperature T{sub C} = 477 °C. This non-linear behavior above T{sub C} is tentatively linked to a diffusion/segregation mechanism of Ag

  14. Stability Evaluation of Buildings in Urban Area Using Persistent Scatterer Interfometry -Focused on Thermal Expansion Effect

    Science.gov (United States)

    Choi, J. H.; Kim, S. W.; Won, J. S.

    2017-12-01

    The objective of this study is monitoring and evaluating the stability of buildings in Seoul, Korea. This study includes both algorithm development and application to a case study. The development focuses on improving the PSI approach for discriminating various geophysical phase components and separating them from the target displacement phase. A thermal expansion is one of the key components that make it difficult for precise displacement measurement. The core idea is to optimize the thermal expansion factor using air temperature data and to model the corresponding phase by fitting the residual phase. We used TerraSAR-X SAR data acquired over two years from 2011 to 2013 in Seoul, Korea. The temperature fluctuation according to seasons is considerably high in Seoul, Korea. Other problem is the highly-developed skyscrapers in Seoul, which seriously contribute to DEM errors. To avoid a high computational burden and unstable solution of the nonlinear equation due to unknown parameters (a thermal expansion parameter as well as two conventional parameters: linear velocity and DEM errors), we separate a phase model into two main steps as follows. First, multi-baseline pairs with very short time interval in which deformation components and thermal expansion can be negligible were used to estimate DEM errors first. Second, single-baseline pairs were used to estimate two remaining parameters, linear deformation rate and thermal expansion. The thermal expansion of buildings closely correlate with the seasonal temperature fluctuation. Figure 1 shows deformation patterns of two selected buildings in Seoul. In the figures of left column (Figure 1), it is difficult to observe the true ground subsidence due to a large cyclic pattern caused by thermal dilation of the buildings. The thermal dilation often mis-leads the results into wrong conclusions. After the correction by the proposed method, true ground subsidence was able to be precisely measured as in the bottom right figure

  15. Conformational and thermal stability improvements for the large-scale production of yeast-derived rabbit hemorrhagic disease virus-like particles as multipurpose vaccine.

    Directory of Open Access Journals (Sweden)

    Erlinda Fernández

    Full Text Available Recombinant virus-like particles (VLP antigenically similar to rabbit hemorrhagic disease virus (RHDV were recently expressed at high levels inside Pichia pastoris cells. Based on the potential of RHDV VLP as platform for diverse vaccination purposes we undertook the design, development and scale-up of a production process. Conformational and stability issues were addressed to improve process control and optimization. Analyses on the structure, morphology and antigenicity of these multimers were carried out at different pH values during cell disruption and purification by size-exclusion chromatography. Process steps and environmental stresses in which aggregation or conformational instability can be detected were included. These analyses revealed higher stability and recoveries of properly assembled high-purity capsids at acidic and neutral pH in phosphate buffer. The use of stabilizers during long-term storage in solution showed that sucrose, sorbitol, trehalose and glycerol acted as useful aggregation-reducing agents. The VLP emulsified in an oil-based adjuvant were subjected to accelerated thermal stress treatments. None to slight variations were detected in the stability of formulations and in the structure of recovered capsids. A comprehensive analysis on scale-up strategies was accomplished and a nine steps large-scale production process was established. VLP produced after chromatographic separation protected rabbits against a lethal challenge. The minimum protective dose was identified. Stabilized particles were ultimately assayed as carriers of a foreign viral epitope from another pathogen affecting a larger animal species. For that purpose, a linear protective B-cell epitope from Classical Swine Fever Virus (CSFV E2 envelope protein was chemically coupled to RHDV VLP. Conjugates were able to present the E2 peptide fragment for immune recognition and significantly enhanced the peptide-specific antibody response in vaccinated pigs

  16. Composition, phase behavior and thermal stability of natural edible fat from rambutan (Nephelium lappaceum L.) seed.

    Science.gov (United States)

    Solís-Fuentes, Julio A; Camey-Ortíz, Guadalupe; Hernández-Medel, María del Rosario; Pérez-Mendoza, Francisco; Durán-de-Bazúa, Carmen

    2010-01-01

    In this paper, the chemical composition, the main physicochemical properties, phase behavior and thermal stability of rambutan (Nephelium lappaceum L.) seed fat were studied. These results showed that the almond-like decorticated seed represents 6.1% of the wet weight fruit and is: 1.22% ash, 7.80% protein, 11.6% crude fiber, 46% carbohydrates, and 33.4% fat (d.b.). The main fatty acids in the drupe fat were 40.3% oleic, 34.5% arachidic, 6.1% palmitic, 7.1% stearic, 6.3% gondoic, and 2.9% behenic; the refraction, saponification and iodine values were 1.468, 186, and 47.0, respectively. The phase behavior analysis showed relatively simple crystallization and melting profiles: crystallization showed three well-differentiated groups of triglycerides around maximum peaks at +30.8, +15.6 and -18.1 degrees C; the fat-melting curve had a range between -14.5 and +51.8 degrees C with a fusion enthalpy of 124.3 J/g. The thermal stability analyzed in an inert atmosphere of N(2) and in a normal oxidizing atmosphere, showed that in the latter, fat decomposition begins at 237.3 degrees C and concludes at 529 degrees C, with three stages of decomposition. According to these results, rambutan seed fat has physicochemical and thermal characteristics that may become interesting for specific applications in several segments of the food industry.

  17. RP-2 Thermal Stability and Heat Transfer Investigation for Hydrocarbon Boost Engines

    Science.gov (United States)

    VanNoord, J. L.; Stiegemeier, B. R.

    2010-01-01

    A series of electrically heated tube tests were performed at the NASA Glenn Research Center s Heated Tube Facility to investigate the use of RP-2 as a fuel for next generation regeneratively cooled hydrocarbon boost engines. The effect that test duration, operating condition and test piece material have on the overall thermal stability and materials compatibility characteristics of RP-2 were evaluated using copper and 304 stainless steel test sections. The copper tests were run at 1000 psia, heat flux up to 6.0 Btu/in.2-sec, and wall temperatures up to 1180 F. Preliminary results, using measured wall temperature as an indirect indicator of the carbon deposition process, show that in copper test pieces above approximately 850 F, RP-2 begins to undergo thermal decomposition resulting in local carbon deposits. Wall temperature traces show significant local temperature increases followed by near instantaneous drops which have been attributed to the carbon deposition/shedding process in previous investigations. Data reduction is currently underway for the stainless steel test sections and carbon deposition measurements will be performed in the future for all test sections used in this investigation. In conjunction with the existing thermal stability database, these findings give insight into the feasibility of cooling a long life, high performance, high-pressure liquid rocket combustor and nozzle with RP-2.

  18. Thermal stability of multilayer graphene films synthesized by chemical vapor deposition and stained by metallic impurities.

    Science.gov (United States)

    Kahng, Yung Ho; Lee, Sangchul; Park, Woojin; Jo, Gunho; Choe, Minhyeok; Lee, Jong-Hoon; Yu, Hyunung; Lee, Takhee; Lee, Kwanghee

    2012-02-24

    Thermal stability is an important property of graphene that requires thorough investigation. This study reports the thermal stability of graphene films synthesized by chemical vapor deposition (CVD) on catalytic nickel substrates in a reducing atmosphere. Electron microscopies, atomic force microscopy, and Raman spectroscopy, as well as electronic measurements, were used to determine that CVD-grown graphene films are stable up to 700 °C. At 800 °C, however, graphene films were etched by catalytic metal nanoparticles, and at 1000 °C many tortuous tubular structures were formed in the film and carbon nanotubes were formed at the film edges and at catalytic metal-contaminated sites. Furthermore, we applied our pristine and thermally treated graphene films as active channels in field-effect transistors and characterized their electrical properties. Our research shows that remnant catalytic metal impurities play a critical role in damaging graphene films at high temperatures in a reducing atmosphere: this damage should be considered in the quality control of large-area graphene films for high temperature applications.

  19. Degradation mechanism and thermal stability of urea nitrate below the melting point

    Energy Technology Data Exchange (ETDEWEB)

    Desilets, Sylvain, E-mail: sylvain.desilets@drdc-rddc.gc.ca [Defence R and D Canada, Valcartier, 2459 Pie-XI Blvd North, Val-Belair, Quebec, Canada G3J 1X5 (Canada); Brousseau, Patrick; Chamberland, Daniel [Defence R and D Canada, Valcartier, 2459 Pie-XI Blvd North, Val-Belair, Quebec, Canada G3J 1X5 (Canada); Singh, Shanti; Feng, Hongtu; Turcotte, Richard [Canadian Explosives Research Laboratory, 1 Haanel Dr. Ottawa, Quebec, Canada K1A 1M1 (Canada); Anderson, John [Defence R and D Canada, Suffield, Box 4000, stn Main, Medicine Hat, Alberta, Canada T1A 8K6 (Canada)

    2011-07-10

    Highlights: {yields} Decomposition mechanism of urea nitrate. {yields} Spectral characterization of the decomposition mechanism. {yields} Thermal stability of urea nitrate at 50, 70 and 100 {sup o}C. {yields} Chemical balance of decomposed products released. - Abstract: Aging and degradation of urea nitrate below the melting point, at 100 {sup o}C, was studied by using thermal analysis and spectroscopic methods including IR, Raman, {sup 1}H and {sup 13}C NMR techniques. It was found that urea nitrate was completely degraded after 72 h at 100 {sup o}C into a mixture of solids (69%) and released gaseous species (31%). The degradation mechanism below the melting point was clearly identified. The remaining solid mixture was composed of ammonium nitrate, urea and biuret while unreacted residual nitric and isocyanic acids as well as traces of ammonia were released as gaseous species at 100 {sup o}C. The thermal stability of urea nitrate, under extreme storage conditions (50 {sup o}C), was also examined by isothermal nano-calorimetry.

  20. Thermal Stability and Kinetic Study of Isotactic Polypropylene/Algerian Bentonite Nanocomposites Prepared via Melt Blending

    Directory of Open Access Journals (Sweden)

    Fayçal Benhacine

    2014-01-01

    Full Text Available Isotactic polypropylene (iPP/bentonite nanocomposites were prepared via melt blending using bentonite clay originated from Maghnia (Algeria. This clay was, at a first stage, used in its pure form (PBT and then organically modified by Hexadecyl ammonium chloride (OBT. The effect of Maghnia bentonite dispersion on the iPP matrix was investigated by X-ray diffraction (XRD and transmission electronic microscopy (TEM. DSC results evidenced that unmodified or organomodified bentonite can act as a nucleating agent increasing the rate of crystallites formation. Moreover, a thermogravimetry analysis confirmed a significant enhanced thermal stability of IPP/clay nanocomposites compared to pure IPP. The Flynn-Wall-Ozawa and Tang methods were applied to determine the activation energy Ea of the degradation process. The apparent activation energy  Eα of thermal degradation for IPP/clay nanocomposites was much higher than that of virgin iPP. Comparatively to PBT, results indicate that OBT has an important effect on pure iPP thermal stability. Tensile modulus, tensile strength, and elongation at break were also measured and compared with those of pure iPP.

  1. Thermal-hydraulics stability of natural circulation BWR under startup. Flashing effects

    International Nuclear Information System (INIS)

    Hu, Rui; Kazimi, Mujid S.

    2009-01-01

    To help achieve the necessary natural circulation flow, a fairly long chimney is installed in a boiling natural circulation reactor like the ESBWR. In such systems, thermal-hydraulic stability during low pressure start-up should be examined while considering the flashing induced by the pressure drop in the channel and the chimney due to gravity head. In this work, a BWR stability analysis code in the frequency domain, named FISTAB (Flashing-Induced STability Analysis for BWR), was developed to address the issue of flashing-induced instability. A thermal-hydraulics non-homogeneous equilibrium model (NHEM) based on a drift flux formulation along with a lumped fuel dynamics model is incorporated in the work. The vapor generation rate is derived from the mixture energy conservation equation while considering the effect of flashing. The functionality of the FISTAB code was confirmed by comparison to experimental results from SIRIUS-N facility at CRIEPI, Japan. Both stationary and perturbation results agree well with the experimental results. (author)

  2. Effect of thermal and high pressure processing on stability of betalain extracted from red beet stalks.

    Science.gov (United States)

    Dos Santos, Cláudia Destro; Ismail, Marliya; Cassini, Aline Schilling; Marczak, Ligia Damasceno Ferreira; Tessaro, Isabel Cristina; Farid, Mohammed

    2018-02-01

    Red beet stalks are a potential source of betalain, but their pigments are not widely used because of their instability. In the present work, the applicability of high pressure processing (HPP) and high temperature short time (HTST) thermal treatment was investigated to improve betalain stability in extracts with low and high concentrations. The HPP was applied at 6000 bar for 10, 20 and 30 min and HTST treatment was applied at 75.7 °C for 80 s, 81.1 °C for 100 s and 85.7 °C for 120 s, HPP treatment did not show any improvement in the betalain stability. In turn, the degradation rate of the control and the HTST thermal treatment at 85.7 °C for 120 s of the sample with high initial betalain concentration were 1.2 and 0.4 mg of betanin/100 ml of extract per day respectively. Among the treatments studied, HTST was considered the most suitable to maintain betalain stability from red beet stalks.

  3. Synthesis, Antibacterial and Thermal Studies of Cellulose Nanocrystal Stabilized ZnO-Ag Heterostructure Nanoparticles

    Directory of Open Access Journals (Sweden)

    Mohd Zobir Hussein

    2013-05-01

    Full Text Available Synthesis of ZnO-Ag heterostructure nanoparticles was carried out by a precipitation method with cellulose nanocrystals (CNCs as a stabilizer for antimicrobial and thermal studies. ZnO-Ag nanoparticles were obtained from various weight percentages of added AgNO3 relative to Zn precursors for evaluating the best composition with enhanced functional properties. The ZnO-Ag/CNCs samples were characterized systematically by TEM, XRD, UV, TGA and DTG. From the TEM studies we observed that ZnO-Ag heterostructure nanoparticles have spherical shapes with size diameters in a 9–35 nm range. The antibacterial activities of samples were assessed against the bacterial species Salmonella choleraesuis and Staphylococcus aureus. The CNC-stabilized ZnO-Ag exhibited greater bactericidal activity compared to cellulose-free ZnO-Ag heterostructure nanoparticles of the same particle size. The incorporation of ZnO-Ag hetreostructure nanoparticles significantly increased the thermal stability of cellulose nanocrystals.

  4. Thermal and chemical stabilities of some synthesized inorganic ion exchange materials

    International Nuclear Information System (INIS)

    El-Naggar, I.M.; Abou-Mesalam, M. M.; El-Shorbagy, M.M.; Shady, S.A.

    2005-01-01

    Chromium and cerium titanate as inorganic ion exchange materials were synthesized by the reaction of potassium chromate or ammonium ceric nitrate with titanium tetrachloride with molar ratio equal unity. The crystal system of both chromium and cerium titanates were determined and set to be monoclinic and orthorhombic systems, respectively. The chemical composition of both chromium and cerium titanates were determined by X-ray fluorescence technique and based on the data obtained with other different techniques. We can proposed molecular formula for chromium and cerium titanates as Cr 2 Ti 1 2O27. 13H 2 O and Ce 2 ThO10. 7.46 H 2 O, respectively. Thermal stability of both ion exchangers was investigated at different heating temperatures. Also the stability of chromium and cerium titanates for chemical attack was studied in different media. The data obtained showed high thermal and chemical stabilities of chromium and cerium titanate ion exchangers compared to the same group of ion exchange materials. The ion exchange capacities of chromium and cerium titanates at different heating temperature were investigated

  5. Box-Behnken experimental design for investigation of stability and thermal conductivity of TiO{sub 2} nanofluids

    Energy Technology Data Exchange (ETDEWEB)

    Lotfizadeh Dehkordi, Babak, E-mail: babakld@siswa.um.edu.my; Ghadimi, Azadeh; Metselaar, Henk S. C., E-mail: h.metselaar@um.edu.my [University of Malaya, Department of Mechanical Engineering, Faculty of Engineering (Malaysia)

    2013-01-15

    The aim of this study is to investigate the effect of ultrasonication on the stability and thermal conductivity of TiO{sub 2} water nanofluids. A UV-Vis spectrophotometer was employed to determine the relative stability of nanofluids. Response surface methodology based on the Box-Behnken design was implemented to investigate the influence of power of sonication (20-80 %), time of sonication (2-20 min), and volume concentration (0.1-1 vol%) of nanofluids as the independent variables. Second-order polynomial equations were established to predict the responses, thermal conductivity, and stability of nanofluids with the intervals of 1 week and 1 month. The significance of the models was tested by means of analysis of variance (ANOVA). The optimum stability and thermal conductivity of TiO{sub 2} nanofluids with various sonication power and time at volume concentrations of 0.1, 0.55, and 1 % were studied. In addition, a correlation between the stability and thermal conductivity enhancement was derived in this study. The results revealed that, at low concentrations, nanofluids would become stable by low power and short period of sonication; however, no enhancement was observed in the thermal conductivity. Conversely, at high concentrations, stability and high thermal conductivity of nanofluids coincided at 1 vol%.

  6. Box–Behnken experimental design for investigation of stability and thermal conductivity of TiO2 nanofluids

    International Nuclear Information System (INIS)

    Lotfizadeh Dehkordi, Babak; Ghadimi, Azadeh; Metselaar, Henk S. C.

    2013-01-01

    The aim of this study is to investigate the effect of ultrasonication on the stability and thermal conductivity of TiO 2 water nanofluids. A UV–Vis spectrophotometer was employed to determine the relative stability of nanofluids. Response surface methodology based on the Box–Behnken design was implemented to investigate the influence of power of sonication (20–80 %), time of sonication (2–20 min), and volume concentration (0.1–1 vol%) of nanofluids as the independent variables. Second-order polynomial equations were established to predict the responses, thermal conductivity, and stability of nanofluids with the intervals of 1 week and 1 month. The significance of the models was tested by means of analysis of variance (ANOVA). The optimum stability and thermal conductivity of TiO 2 nanofluids with various sonication power and time at volume concentrations of 0.1, 0.55, and 1 % were studied. In addition, a correlation between the stability and thermal conductivity enhancement was derived in this study. The results revealed that, at low concentrations, nanofluids would become stable by low power and short period of sonication; however, no enhancement was observed in the thermal conductivity. Conversely, at high concentrations, stability and high thermal conductivity of nanofluids coincided at 1 vol%.

  7. Function of VP2 protein in the stability of the secondary structure of virus-like particles of genogroup II norovirus at different pH levels: function of VP2 protein in the stability of NoV VLPs.

    Science.gov (United States)

    Lin, Yao; Fengling, Li; Lianzhu, Wang; Yuxiu, Zhai; Yanhua, Jiang

    2014-11-01

    VP2 is the minor structural protein of noroviruses (NoV) and may function in NoV particle stability. To determine the function of VP2 in the stability of the NoV particle, we constructed and purified two kinds of virus-like particles (VLPs), namely, VLPs (VP1) and VLPs (VP1+VP2), from Sf9 cells infected with recombinant baculoviruses by using a Bac-to-Bac® baculovirus expression system. The two kinds of VLPs were treated with different phosphate buffers (pH 2 to pH 8); the secondary structure was then analyzed by far UV circular dichroism (CD) spectroscopy. Results showed that significant disruptions of the secondary structure of proteins were not observed at pH 2 to pH 7. At pH 8, the percentages of a-helix, β-sheet, and β-turn in VLPs (VP1) were decreased from 11% to 8%, from 37% to 32%, and from 20% to 16%, respectively. The percentage of coil was increased from 32% to 44%. By contrast, the percentages of α-helix, β-sheet, and β-turn in VLPs (VP1+VP2) were decreased from 11% to 10%, from 37% to 35%, and from 20% to 19%, respectively. The percentage of coil was increased from 32% to 36%. VLPs (VP1+VP2) was likely more stable than VLPs (VP1), as indicated by the percentage of the secondary structures analyzed by CD. These results suggested that VP2 could stabilize the secondary structure of VLPs under alkaline pH conditions. This study provided novel insights into the molecular mechanism of the function of VP2 in the stability of NoV particles.

  8. Improved electrical stability of CdS thin film transistors through Hydrogen-based thermal treatments

    KAUST Repository

    Salas Villaseñor, Ana L.

    2014-06-01

    Thin film transistors (TFTs) with a bottom-gate configuration were fabricated using a photolithography process with chemically bath deposited (CBD) cadmium sulfide (CdS) films as the active channel. Thermal annealing in hydrogen was used to improve electrical stability and performance of the resulting CdS TFTs. Hydrogen thermal treatments results in significant V T instability (V T shift) improvement while increasing the I on/I off ratio without degrading carrier mobility. It is demonstrated that after annealing V T shift and I on/I off improves from 10 V to 4.6 V and from 105 to 10 9, respectively. Carrier mobility remains in the order of 14.5 cm2 V s-1. The reduced V T shift and performance is attributed to a reduction in oxygen species in the CdS after hydrogen annealing, as evaluated by Fourier transform infrared spectroscopy (FTIR). © 2014 IOP Publishing Ltd.

  9. Study of thermal stability of Cu{sub 2}Se thermoelectric material

    Energy Technology Data Exchange (ETDEWEB)

    Bohra, Anil, E-mail: anilbohra786@gmail.com; Bhatt, Ranu; Bhattacharya, Shovit; Basu, Ranita; Singh, Ajay; Aswal, D. K.; Gupta, S. K. [Technical Physics Division, B.A.R.C., Trombay, Mumbai – 400085 (India); Ahmad, Sajid [Nuclear Research Laboratory, Astrophysical Sciences Division, B.A.R.C., Zakura, Srinagar– 190006 (India)

    2016-05-23

    Sustainability of thermoelectric parameter in operating temperature range is a key consideration factor for fabricating thermoelectric generator or cooler. In present work, we have studied the stability of thermoelectric parameter of Cu{sub 2}Se within the temperature range of 50-800°C. Temperature dependent Seebeck coefficients and electrical resistivity measurement are performed under three continuous thermal cycles. X-ray diffraction pattern shows the presence of mixed cubic-monoclinic Cu{sub 2}Se phase in bare pellet which transforms to pure α-Cu{sub 2}Se phase with repeating thermal cycle. Significant enhancement in Seebeck coefficient and electrical resistivity is observed which may be attributed to (i) Se loss observed in EDS and (ii) the phase transformation from mixed cubic-monoclinic structure to pure monoclinic α-Cu{sub 2}Se phase.

  10. Study of Thermal Stress Influence on Dimensional Stability of Silicone Molds

    Science.gov (United States)

    Bajčičák, Martin; Šuba, Roland

    2014-06-01

    The paper is focused on the study of temperature influence on dimensional stability of silicone molds used for spin casting of the low melting points alloys. The silicone material denoted as TEKSIL Silicone-GP-S was used to produce samples during experiments. The samples were heated to temperatures in the range from 100 up to 250oC for 30 up to 120 min. Dimensional changes of the samples in the radial and axial directions aa well as their change of weight were evaluated. The results of experiments proved that thermal stress of silicone molds can influence the size and shape of mold cavities. These results can also explain the possible mechanism of degradation process of silicone molds under thermal stress.

  11. Synthesis, structural properties and thermal stability of Mn-doped hydroxyapatite

    Science.gov (United States)

    Paluszkiewicz, Czesława; Ślósarczyk, Anna; Pijocha, Dawid; Sitarz, Maciej; Bućko, Mirosław; Zima, Aneta; Chróścicka, Anna; Lewandowska-Szumieł, Małgorzata

    2010-07-01

    Hydroxyapatite (HA) - Ca 10(PO 4) 6(OH) 2 is a basic inorganic model component of hard biological tissues, such as bones and teeth. The significant property of HA is its ability to exchange Ca 2+ ions, which influences crystallinity, physico-chemical and biological properties of modified hydroxyapatite materials. In this work, FTIR, Raman spectroscopy, XRD, SEM and EDS techniques were used to determine thermal stability, chemical and phase composition of Mn containing hydroxyapatite (MnHA). Described methods confirmed thermal decomposition and phase transformation of MnHA to αTCP, βTCP and formation of Mn 3O 4 depending on sintering temperature and manganese content. In vitro biological evaluation of Mn-modified HA ceramics was also performed using human osteoblast cells.

  12. A simple hydrothermal route to bimodal mesoporous nanorod {gamma}-alumina with high thermal stability

    Energy Technology Data Exchange (ETDEWEB)

    Li, Xiang; Han, Dezhi; Xue, Hongxia; Liu, Xinmei; Yan, Zifeng [China Univ. of Petroleum, Qingdao (China). State Key Lab. of Heavy Oil Processing

    2011-12-15

    In the presence of polyethylene glycol, bimodal mesoporous nanorod {gamma}-alumina was successfully synthesized via the thermal decomposition of ammonium aluminium carbonate hydroxide precursor which was prepared via hydrothermal processing with inorganic aluminium salt. The alumina exhibits high surface area (494 m{sup 2}g{sup -1}), large porosity (1.1 m{sup 3}g{sup -1}) and a particular double-pore structure after calcination at 500 C. The smaller pore diameter is concentrated on about 3 nm and the larger one is exhibited in the range of 10 - 38 nm. The scaffold-like aggregation of {gamma}-alumina nanorods endows this novel material with excellent thermal stability. A possible formation mechanism of bimodal mesoporous structure is also proposed in this study. (orig.)

  13. Comparison of thermal stability of grape seed oil with virgin sesame oil

    Directory of Open Access Journals (Sweden)

    Marzieh

    2015-11-01

    Full Text Available Background: Heating causes extensive physical and chemical changes in oil and fats, which can change all physical and chemical characteristics and quality of oil during frying is so critical. This study was aimed to compare the thermal stability of virgin sesame oil and grape seed oil. Methods: The grape seed oil and virgin sesame oil were heated at 180 ° C for 8 hours. Every hour, a sample of the heated oils was taken to determine the changes in acid value, peroxide, anisidine and Totox. Results: Heating the oil caused extensive chemical variations both oils. The acidity index increased over time (p<0.05, there were fluctuations inperoxide value, and anisidine and Totox values also increased during thermal processes (p<0.05. Conclusion: Grape seed oil showed more resistance to heat than sesame oil.

  14. Study of Thermal Stress Influence on Dimensional Stability of Silicone Molds

    Directory of Open Access Journals (Sweden)

    Bajčičák Martin

    2014-06-01

    Full Text Available The paper is focused on the study of temperature influence on dimensional stability of silicone molds used for spin casting of the low melting points alloys. The silicone material denoted as TEKSIL Silicone-GP-S was used to produce samples during experiments. The samples were heated to temperatures in the range from 100 up to 250oC for 30 up to 120 min. Dimensional changes of the samples in the radial and axial directions aa well as their change of weight were evaluated. The results of experiments proved that thermal stress of silicone molds can influence the size and shape of mold cavities. These results can also explain the possible mechanism of degradation process of silicone molds under thermal stress.

  15. Linear and nonlinear stability of a thermally stratified magnetically driven rotating flow in a cylinder.

    Science.gov (United States)

    Grants, Ilmars; Gerbeth, Gunter

    2010-07-01

    The stability of a thermally stratified liquid metal flow is considered numerically. The flow is driven by a rotating magnetic field in a cylinder heated from above and cooled from below. The stable thermal stratification turns out to destabilize the flow. This is explained by the fact that a stable stratification suppresses the secondary meridional flow, thus indirectly enhancing the primary rotation. The instability in the form of Taylor-Görtler rolls is consequently promoted. These rolls can only be excited by finite disturbances in the isothermal flow. A sufficiently strong thermal stratification transforms this nonlinear bypass instability into a linear one reducing, thus, the critical value of the magnetic driving force. A weaker temperature gradient delays the linear instability but makes the bypass transition more likely. We quantify the non-normal and nonlinear components of this transition by direct numerical simulation of the flow response to noise. It is observed that the flow sensitivity to finite disturbances increases considerably under the action of a stable thermal stratification. The capabilities of the random forcing approach to identify disconnected coherent states in a general case are discussed.

  16. Thermal stability and crystallization kinetics of quaternary Sb–Se–Ge–In chalcogenide glasses

    International Nuclear Information System (INIS)

    Sharda, Sunanda; Sharma, Neha; Sharma, Pankaj; Sharma, Vineet

    2014-01-01

    Highlights: • DTA has been carried out on Sb 10 Se 65 Ge 25−y In y alloys under non-isothermal conditions at different heating rates. • E g with In content shows that probability of atoms to jump to lower metastable states increases. • The heating rate dependence of crystallization temperature shows that E c decreases. - Abstract: Thermal analysis plays an important role to know the characteristic behavior of alloys for various applications. Differential thermal analysis has been carried out on Sb 10 Se 65 Ge 25−y In y (y = 0, 3, 6, 9, 12, 15) alloys under non-isothermal conditions at different heating rates. We report the analysis of thermal parameters, viz. glass transition temperature, crystallization temperature and melting temperature. The thermal stability factor, reduced glass transition temperature, and heating rate dependence of glass transition and crystallization peaks have been investigated. The dependence of activation energies of glass transition and crystallization with In content have been discussed in terms of energy barrier and chemical bond approach respectively

  17. The influence of pH and temperature on the stability of flutamide. An HPLC investigation and identification of the degradation product by EI+-MS

    OpenAIRE

    El-Shaheny, Rania Nabih; Yamada, Koji

    2014-01-01

    The chemical stability of flutamide (FLT) was investigated using a new validated stability-indicating HPLC method. Separation of FLT from its degradation product was achieved on a C18 column using a mobile phase of methanol-phosphate buffer (0.04 M, pH 4.0) (75:25, v/v) with UV-detection at 240 nm. The method exhibited excellent linearity for FLT over the concentration range of 0.2-25.0 μg mL-1. FLT was found to be labile to degradation in buffered, acidic and alkaline solutions. The degradat...

  18. Correlation between calculated molecular descriptors of excipient amino acids and experimentally observed thermal stability of lysozyme

    DEFF Research Database (Denmark)

    Meng-Lund, Helena; Friis, Natascha; van de Weert, Marco

    2017-01-01

    analysis was applied to correlate the descriptors with the experimental results. It was possible to identify descriptors, i.e. amino acids properties, with a positive influence on either transition temperature or aggregation onset time, or both. A high number of hydrogen bond acceptor moieties was the most......A quantitative structure-property relationship (QSPR) between protein stability and the physicochemical properties of excipients was investigated to enable a more rational choice of stabilizing excipients than prior knowledge. The thermal transition temperature and aggregation time were determined...... for lysozyme in combination with 13 different amino acids using high throughput fluorescence spectroscopy and kinetic static light scattering measurements. On the theoretical side, around 200 2D and 3D molecular descriptors were calculated based on the amino acids' chemical structure. Multivariate data...

  19. Effect of thermal stabilization on the low-temperature stress-corrosion cracking of Inconel 600

    International Nuclear Information System (INIS)

    Bandy, R.; van Rooyen, D.

    1983-01-01

    The propensity to low-temperature stress-corrosion cracking (SCC) of thermally stabilized Inconel 600 in sulfur-bearing environments has been investigated using U-bends and slow-strain-rate testing. The results have been compared with those of sensitized Inconel 600. The potential dependence of crack-propagation rate has been established in a single test by using several U-bends held at different potentials, by choosing an appropriate electrical circuitry. The difference in SCC susceptibility of the sensitized and stabilized materials is discussed in terms of the grain-boundary chromium depletion and resulting intergranular attack in boiling ferric sulfate-sulfuric acid tests, and electrochemical potentiokinetic reactivation (EPR) tests. 10 figures

  20. Metal-dielectric interfaces in gigascale electronics thermal and electrical stability

    CERN Document Server

    He, Ming

    2012-01-01

    Metal-dielectric interfaces are ubiquitous in modern electronics. As advanced gigascale electronic devices continue to shrink, the stability of these interfaces is becoming an increasingly important issue that has a profound impact on the operational reliability of these devices. In this book, the authors present the basic science underlying  the thermal and electrical stability of metal-dielectric interfaces and its relationship to the operation of advanced interconnect systems in gigascale electronics. Interface phenomena, including chemical reactions between metals and dielectrics, metallic-atom diffusion, and ion drift, are discussed based on fundamental physical and chemical principles. Schematic diagrams are provided throughout the book to illustrate  interface phenomena and the principles that govern them. Metal-Dielectric Interfaces in Gigascale Electronics  provides a unifying approach to the diverse and sometimes contradictory test results that are reported in the literature on metal-dielectric i...

  1. Ferromagnetic and Antiferromagnetic Coupling of Spin Molecular Interfaces with High Thermal Stability.

    Science.gov (United States)

    Avvisati, Giulia; Cardoso, Claudia; Varsano, Daniele; Ferretti, Andrea; Gargiani, Pierluigi; Betti, Maria Grazia

    2018-03-26

    We report an advanced organic spin-interface architecture with magnetic remanence at room temperature, constituted by metal phthalocyanine molecules magnetically coupled with Co layer(s), mediated by graphene. Fe- and Cu-phthalocyanines assembled on graphene/Co have identical structural configurations, but FePc couples antiferromagnetically with Co up to room temperature, while CuPc couples ferromagnetically with weaker coupling and thermal stability, as deduced by element-selective X-ray magnetic circular dichroic signals. The robust antiferromagnetic coupling is stabilized by a superexchange interaction, driven by the out-of-plane molecular orbitals responsible of the magnetic ground state and electronically decoupled from the underlying metal via the graphene layer, as confirmed by ab initio theoretical predictions. These archetypal spin interfaces can be prototypes to demonstrate how antiferromagnetic and/or ferromagnetic coupling can be optimized by selecting the molecular orbital symmetry.

  2. Effect of the thermal stabilization temperature on the change in the texture of polyacrylonitrile fiber

    Science.gov (United States)

    Fazlitdinova, A. G.; Tyumentsev, V. A.

    2015-11-01

    The effect of temperature of isothermal treatment on the change in sizes L 010 of coherent scattering regions and texture of a polyacrylonitrile fiber during its transition to the structure of a thermally stabilized fiber is analyzed using X-ray structure analysis. An increase in the thermostabilization temperature at a constant stretching load stimulates simultaneously a more active increase in size L 010 and texturing of polyacrylonitrile fibers at the initial stage. Active evolution of the phase transformation at temperatures 275-290°C during further thermostabilization is accompanied by a substantial decrease in the texture of the polymer that has not experienced the phase transformation by this instant.

  3. Contribution of thermal noise to frequency stability of rigid optical cavity via Hertz-linewidth lasers

    International Nuclear Information System (INIS)

    Notcutt, Mark; Ma, L.-S.; Ludlow, Andrew D.; Foreman, Seth M.; Ye Jun; Hall, John L.

    2006-01-01

    We perform detailed studies of state-of-the-art laser stabilization to high finesse optical cavities, revealing fundamental mechanical thermal noise-related length fluctuations. We compare the frequency noise of lasers tightly locked to the resonances of a variety of rigid Fabry-Perot cavities of differing lengths and mirror substrate materials. The results are in agreement with the theoretical model proposed in K. Numata, A. Kemery, and J. Camp [Phys. Rev. Lett. 93, 250602 (2004)]. The results presented here on the fundamental limits of FP references will impact planning and construction of next generation ultrastable optical cavities

  4. Effects of monohydric alcohols and polyols on the thermal stability of a protein

    Science.gov (United States)

    Murakami, Shota; Kinoshita, Masahiro

    2016-03-01

    The thermal stability of a protein is lowered by the addition of a monohydric alcohol, and this effect becomes larger as the size of hydrophobic group in an alcohol molecule increases. By contrast, it is enhanced by the addition of a polyol possessing two or more hydroxyl groups per molecule, and this effect becomes larger as the number of hydroxyl groups increases. Here, we show that all of these experimental observations can be reproduced even in a quantitative sense by rigid-body models focused on the entropic effect originating from the translational displacement of solvent molecules. The solvent is either pure water or water-cosolvent solution. Three monohydric alcohols and five polyols are considered as cosolvents. In the rigid-body models, a protein is a fused hard spheres accounting for the polyatomic structure in the atomic detail, and the solvent is formed by hard spheres or a binary mixture of hard spheres with different diameters. The effective diameter of cosolvent molecules and the packing fractions of water and cosolvent, which are crucially important parameters, are carefully estimated using the experimental data of properties such as the density of solid crystal of cosolvent, parameters in the pertinent cosolvent-cosolvent interaction potential, and density of water-cosolvent solution. We employ the morphometric approach combined with the integral equation theory, which is best suited to the physical interpretation of the calculation result. It is argued that the degree of solvent crowding in the bulk is the key factor. When it is made more serious by the cosolvent addition, the solvent-entropy gain upon protein folding is magnified, leading to the enhanced thermal stability. When it is made less serious, the opposite is true. The mechanism of the effects of monohydric alcohols and polyols is physically the same as that of sugars. However, when the rigid-body models are employed for the effect of urea, its addition is predicted to enhance the

  5. Comparison of thermal stability of grape seed oil with virgin sesame oil

    OpenAIRE

    Marzieh; Peyman; Fayegh Moulodi

    2015-01-01

    Background: Heating causes extensive physical and chemical changes in oil and fats, which can change all physical and chemical characteristics and quality of oil during frying is so critical. This study was aimed to compare the thermal stability of virgin sesame oil and grape seed oil. Methods: The grape seed oil and virgin sesame oil were heated at 180 ° C for 8 hours. Every hour, a sample of the heated oils was taken to determine the changes in acid value, peroxide, anisidine and Totox. ...

  6. Effect of adsorbed polyaniline on the thermal stability of iron and arsenic oxides

    Directory of Open Access Journals (Sweden)

    Robson Fernandes de Farias

    2000-06-01

    Full Text Available Iron and arsenic oxide grains are coated with the conducting organic polymer polyaniline. The obtained samples were characterized by infrared spectroscopy, SEM, conducting measurements and thermogravimetry. The thermal stability of both oxides are increased. For As2O3 the sublimation temperature is increased from 165ºC in the pure oxide to 206ºC in the polymer modified sample. The pure Fe3O4 sample exhibits sublimation at 780ºC whereas the polyaniline coated oxide is stable until at least 1000ºC.

  7. Thermal stability of Al-Cu-Fe quasicrystals prepared by SHS method

    Directory of Open Access Journals (Sweden)

    Pavel Novak

    2013-02-01

    Full Text Available Quasicrystal-containing materials are usually prepared by rapid solidification of the melt (e.g. by melt spinning or mechanical alloying. In this work, the method using exothermic reactions between compressed metallic powders called SHS (Self-propagating High-temperature Synthesis was tested. The microstructure and phase composition of the product was described in dependence on cooling regime from the reaction temperature. Thermal stability of prepared Al-Cu-Fe quasicrystals was studied by annealing at the temperatures of 300 and 500 °C.

  8. THERMAL STABILITY OF Al-Cu-Fe QUASICRYSTALS PREPARED BY SHS METHOD

    Directory of Open Access Journals (Sweden)

    Pavel Novák

    2013-04-01

    Full Text Available Quasicrystal-containing materials are usually prepared by rapid solidification of the melt (e.g. by melt spinning or mechanical alloying. In this work, the method using exothermic reactions between compressed metallic powders called SHS (Self-propagating High-temperature Synthesis was tested. The microstructure and phase composition of the product was described in dependence on cooling regime from the reaction temperature. Thermal stability of prepared Al-Cu-Fe quasicrystals was studied by annealing at the temperatures of 300 and 500 °C.

  9. Effects of modified Clay on the morphology and thermal stability of PMMA/clay nanocomposites

    International Nuclear Information System (INIS)

    Tsai, Tsung-Yen; Lin, Mei-Ju; Chuang, Yi-Chen; Chou, Po-Chiang

    2013-01-01

    The potential to improve the mechanical, thermal, and optical properties of poly(methyl methacrylate) (PMMA)/clay nanocomposites prepared with clay containing an organic modifier was investigated. Pristine sodium montmorillonite clay was modified using cocoamphodipropionate, which absorbs UVB in the 280–320 nm range, via ion exchange to enhance the compatibility between the clay platelets and the methyl methacrylate polymer matrix. PMMA/clay nanocomposites were synthesized via in situ free-radical polymerization. Three types of clay with various cation-exchange capacities (CEC) were used as inorganic layered materials in these organic–inorganic hybrid nanocomposites: CL42, CL120, and CL88 with CEC values of 116, 168, and 200 meq/100 g of clay, respectively. We characterized the effects of the organoclay dispersion on UV resistance, effectiveness as an O 2 gas barrier, thermal stability, and mechanical properties of PMMA/clay nanocomposites. Gas permeability analysis demonstrated the excellent gas barrier properties of the nanocomposites, consistent with the intercalated or exfoliated morphologies observed. The optical properties were assessed using UV–Visible spectroscopy, which revealed that these materials have good optical clarity, UV resistance, and scratch resistance. The effect of the dispersion capability of organoclay on the thermal properties of PMMA/clay nanocomposites was investigated by thermogravimetric analysis and differential scanning calorimetry; these analyses revealed excellent thermal stability of some of the modified clay nanocomposites. - Highlights: ► We control the dispersion morphology by protonation of K2 into the clay. ► The CL120 and CL88, with the higher CEC, are more random intercalated by K2. ► We report these materials have good optical clarity, and UV resistance

  10. Thermal Stability, Combustion Behavior, and Mechanical Property in a Flame-Retardant Polypropylene System

    Directory of Open Access Journals (Sweden)

    Lili Wang

    2017-01-01

    Full Text Available In order to comprehensively improve the strength, toughness, flame retardancy, smoke suppression, and thermal stability of polypropylene (PP, layered double hydroxide (LDH Ni0.2Mg2.8Al–LDH was synthesized by a coprecipitation method coupled with the microwave-hydrothermal treatment. The X-ray diffraction (XRD, morphology, mechanical, thermal, and fire properties for PP composites containing 1 wt %–20 wt % Ni0.2Mg2.8Al–LDH were investigated. The cone calorimeter tests confirm that the peak heat release rate (pk–HRR of PP–20%LDH was decreased to 500 kW/m2 from the 1057 kW/m2 of PP. The pk–HRR, average mass loss rate (AMLR and effective heat of combustion (EHC analysis indicates that the condensed phase fire retardant mechanism of Ni0.2Mg2.8Al–LDH in the composites. The production rate and mean release yield of CO for composites gradually decrease as Ni0.2Mg2.8Al–LDH increases in the PP matrix. Thermal analysis indicates that the decomposition temperature for PP–5%LDH and PP–10%LDH is 34 °C higher than that of the pure PP. The mechanical tests reveal that the tensile strength of PP–1%LDH is 7.9 MPa higher than that of the pure PP. Furthermore, the elongation at break of PP–10%LDH is 361% higher than PP. In this work, the synthetic LDH Ni0.2Mg2.8Al–LDH can be used as a flame retardant, smoke suppressant, thermal stabilizer, reinforcing, and toughening agent of PP products.

  11. Donor-Acceptor Interface Stabilizer Based on Fullerene Derivatives toward Efficient and Thermal Stable Organic Photovoltaics.

    Science.gov (United States)

    Li, Junli; Zhu, Xiaoguang; Yuan, Tao; Shen, Jiulin; Liu, Jikang; Zhang, Jian; Tu, Guoli

    2017-02-22

    An interface stabilizer based on alkylation-functionalized fullerene derivatives, [6, 6]-Phenyl-C61-butyric acid (3,5-bis(octyloxy)phenyl)methyl ester (PCB-C8oc), was successfully synthesized and applied for the active layer of Organic Photovoltaics (OPVs). The PCB-C8oc can replace part of the phenyl-C61-buty-ric acid methyl ester (PCBM) and be distributed on the interface of poly(3-hexylthiophene) (P3HT) and PCBM to form P3HT/PCBM/PCB-C8oc ternary blends, leading to thermally stable and efficient organic photovoltaics. The octyl groups of PCB-C8oc exhibit intermolecular interaction with the hexyl groups of P3HT, and the fullerene unit of PCB-C8oc are in tight contact with PCBM. The dual functions of PCB-C8oc will inhibit the phase separation between electron donor and acceptor, thereby improving the stability of devices under long-time thermal annealing at high temperature. When doped with 10 wt % PCB-C8oc, the power conversion efficiency (PCE) of the P3HT system decreased from 3.54% to 2.88% after 48 h of thermal treatment at 150 °C, whereas the PCE of the reference device without PCB-C8oc dramatically dropped from 3.53% to 0.73%. When doping 10 or 20 wt % PCB-C8oc, the unannealed P3HT/PCBM/PCB-C8oc device achieved a higher PCE than the P3HT/PCBM device without any annealing following the same fabricating condition. For the PTB7/PCBM-based devices, after adding only 5 wt % PCB-C8oc, the OPVs also exhibited thermally stable morphology and better device performances. All these results demonstrate that the utilization of alkyl interchain interactions is an effective and practical strategy to control morphological evolution.

  12. Thermal Treatment of Iron Oxide Stabilized APC Residues from Waste Incineration and the Effect on Heavy Metal Binding

    DEFF Research Database (Denmark)

    Sørensen, Mette Abildgaard; Stackpoole, M.; Bender-Koch, C.

    2000-01-01

    Iron oxide stabilized APC residues from MSWI were heat treated at 600°C and 900°C. The thermal treatments resulted in a change in product stability by forcing a transformation in the mineralogical structures of the products. The treatments, moreover, simulated somewhat the natural aging processes...... that would take place in a stabilized residue. Consequent changes in crystalline structure and heavy metal binding were examined....

  13. Thermal and shape stability of high-index-faceted rhodium nanoparticles: a molecular dynamics investigation.

    Science.gov (United States)

    Zeng, Xiang-Ming; Huang, Rao; Wen, Yu-Hua; Sun, Shi-Gang

    2015-02-28

    Nanosized noble metallic particles enclosed by high-index facets exhibit superior catalytic activity because of their high density of low-coordinated step atoms at the surface, and thus have attracted growing interest over the past decade. In this article, we employed molecular dynamics simulations to investigate the thermodynamic evolution of tetrahexahedral Rh nanoparticles respectively covered by {210}, {310}, and {830} facets during the heating process. Our results reveal that the {210} faceted nanoparticle exhibits better thermal and shape stability than the {310} and {830} faceted ones. Meanwhile, because the {830} facet consists of {210} and {310} subfacets, the stability of the {830} faceted Rh nanoparticle is dominated by the {310} subfacet, which possesses a relatively poor stability. Furthermore, the shape transformation of these nanoparticles occurs much earlier than their melting. Further analyses indicate that surface atoms with higher coordination numbers display lower surface diffusivity, and are thus more helpful for stabilizing the particle shape. This study offers an atomistic understanding of the thermodynamic behaviors of high-index-faceted Rh nanoparticles.

  14. Peptide Dendrons as Thermal-Stability Amplifiers for Immunoglobulin G1 Monoclonal Antibody Biotherapeutics.

    Science.gov (United States)

    Bansal, Rohit; Dhawan, Sameer; Chattopadhyay, Soumili; Maurya, Govind P; Haridas, V; Rathore, Anurag S

    2017-10-18

    Biotherapeutics such as monoclonal antibodies (mAbs) have a major share of the pharmaceutical industry for treatment of life-threatening chronic diseases such as cancer, skin ailments, and immune disorders. Instabilities such as aggregation, fragmentation, oxidation, and reduction have resulted in the practice of storing these products at low temperatures (-80 to -20 °C). However, reliable storage at these temperatures can be a challenge, particularly in developing and underdeveloped countries; hence, lately, there has been a renewed interest in creating formulations that would offer stability at higher temperatures (25 to 55 °C). Most therapeutic formulations contain excipients such as salts, sugars, amino acids, surfactants, and polymers to provide stability to the biotherapeutic, but their efficacy at high temperatures is limited. The current work proposes the use of peptide dendrons of different generations to create formulations that would be stable at high temperature. Among these dendrons, third-generation lysine dendron L6 has been identified to provide the highest stability to mAbs, as demonstrated by a host of analytical techniques such as size-exclusion chromatography (SEC), dynamic light scattering (DLS), Nanoparticle tracking Analysis (NTA), and circular dichroism (CD). The biocompatibility of these dendrons was confirmed by hemolytic activity tests. Non-interference of the dendrons with the activity of the mAb was confirmed using a surface plasmon resonance (SPR) based activity assay. We hope that this study will stimulate utilization of such higher-generation dendrons for enhancing the thermal stability of mAbs.

  15. Thermal Stability-Enhanced and High-Efficiency Planar Perovskite Solar Cells with Interface Passivation.

    Science.gov (United States)

    Zhang, Weihai; Xiong, Juan; Jiang, Li; Wang, Jianying; Mei, Tao; Wang, Xianbao; Gu, Haoshuang; Daoud, Walid A; Li, Jinhua

    2017-11-08

    As the electron transport layer (ETL) of perovskite solar cells, oxide semiconductor zinc oxide (ZnO) has been attracting great attention due to its relatively high mobility, optical transparency, low-temperature fabrication, and good environment stability. However, the nature of ZnO will react with the patron on methylamine, which would deteriorate the performance of cells. Although many methods, including high-temperature annealing, doping, and surface modification, have been studied to improve the efficiency and stability of perovskite solar cells with ZnO ETL, devices remain relatively low in efficiency and stability. Herein, we adopted a novel multistep annealing method to deposit a porous PbI 2 film and improved the quality and uniformity of perovskite films. The cells with ZnO ETL were fabricated at the temperature of perovskite film. Interestingly, the PCE of PCBM-passivated cells could reach nearly 19.1%. To our best knowledge, this is the highest PCE value of ZnO-based perovskite solar cells until now. More importantly, PCBM modification could effectively suppress the decomposition of MAPbI 3 and improve the thermal stability of cells. Therefore, the ZnO is a promising candidate of electron transport material for perovskite solar cells in future applications.

  16. Correlation between calculated molecular descriptors of excipient amino acids and experimentally observed thermal stability of lysozyme.

    Science.gov (United States)

    Meng-Lund, Helena; Friis, Natascha; van de Weert, Marco; Rantanen, Jukka; Poso, Antti; Grohganz, Holger; Jorgensen, Lene

    2017-05-15

    A quantitative structure-property relationship (QSPR) between protein stability and the physicochemical properties of excipients was investigated to enable a more rational choice of stabilizing excipients than prior knowledge. The thermal transition temperature and aggregation time were determined for lysozyme in combination with 13 different amino acids using high throughput fluorescence spectroscopy and kinetic static light scattering measurements. On the theoretical side, around 200 2D and 3D molecular descriptors were calculated based on the amino acids' chemical structure. Multivariate data analysis was applied to correlate the descriptors with the experimental results. It was possible to identify descriptors, i.e. amino acids properties, with a positive influence on either transition temperature or aggregation onset time, or both. A high number of hydrogen bond acceptor moieties was the most prominent stabilizing factor for both responses, whereas hydrophilic surface properties and high molecular mass density mostly had a positive influence on the unfolding temperature. A high partition coefficient (logP(o/w)) was identified as the most prominent destabilizing factor for both responses. The QSPR shows good correlation between calculated molecular descriptors and the measured stabilizing effect of amino acids on lysozyme. Copyright © 2017 Elsevier B.V. All rights reserved.

  17. Stability of dye-sensitized solar cells under extended thermal stress.

    Science.gov (United States)

    Yadav, Surendra K; Ravishankar, Sandheep; Pescetelli, Sara; Agresti, Antonio; Fabregat-Santiago, Francisco; Di Carlo, Aldo

    2017-08-23

    In the last few decades, dye-sensitized solar cell (DSC) technology has been demonstrated to be a promising candidate for low cost energy production due to cost-effective materials and fabrication processes. Arguably, DSC stability is the biggest challenge for making this technology appealing for industrial exploitation. This work provides further insight into the stability of DSCs by considering specific dye-electrolyte systems characterized by Raman and impedance spectroscopy analysis. In particular, two ruthenium-based dyes, Z907 and Ru505, and two commercially available electrolytes, namely, the high stability electrolyte (HSE) and solvent-free Livion 12 (L-12), were tested. After 4700 h of thermal stress at 85 °C, the least stable device composed of Z907/HSE showed an efficiency degradation rate of ∼14%/1000 h, while the Ru505/L-12 system retained 96% of its initial efficiency by losing ∼1% each 1000 h. The present results show a viable route to stabilize the DSC technology under prolonged annealing conditions complying with the IEC standard requirements.

  18. Rescue of glaucoma-causing mutant myocilin thermal stability by chemical chaperones

    Science.gov (United States)

    Burns, J. Nicole; Orwig, Susan D.; Harris, Julia L.; Watkins, J. Derrick; Vollrath, Douglas; Lieberman, Raquel L.

    2010-01-01

    Mutations in myocilin cause an inherited form of open angle glaucoma, a prevalent neurodegenerative disorder associated with increased intraocular pressure. Myocilin forms part of the trabecular meshwork extracellular matrix presumed to regulate intraocular pressure. Missense mutations, clustered in the olfactomedin (OLF) domain of myocilin, render the protein prone to aggregation in the endoplasmic reticulum of trabecular meshwork cells, causing cell dysfunction and death. Cellular studies have demonstrated temperature-sensitive secretion of myocilin mutants, but difficulties in expression and purification have precluded biophysical characterization of wild-type (wt) myocilin and disease-causing mutants in vitro. We have overcome these limitations by purifying wt and select glaucoma-causing mutant (D380A, I477N, I477S, K423E) forms of the OLF domain (228–504) fused to maltose binding protein (MBP) from E. coli. Monomeric fusion proteins can be isolated in solution. To determine the relative stability of wt and mutant OLF domains, we developed a fluorescence thermal stability assay without removal of MBP, and provide the first direct evidence that mutated OLF is folded but less thermally stable than wt. We tested the ability of seven chemical chaperones to stabilize mutant myocilin. Only sarcosine and trimethylamine N-oxide were capable of shifting the melting temperature of all mutants tested to near that of wt OLF. Our work lays the foundation for the identification of tailored small molecules capable of stabilizing mutant myocilin and promoting secretion to the extracellular matrix, to better control intraocular pressure and ultimately delay the onset of myocilin glaucoma. PMID:20334347

  19. Thermal stability and kinetic constants for 129 variants of a family 1 glycoside hydrolase reveal that enzyme activity and stability can be separately designed.

    Directory of Open Access Journals (Sweden)

    Dylan Alexander Carlin

    Full Text Available Accurate modeling of enzyme activity and stability is an important goal of the protein engineering community. However, studies seeking to evaluate current progress are limited by small data sets of quantitative kinetic constants and thermal stability measurements. Here, we report quantitative measurements of soluble protein expression in E. coli, thermal stability, and Michaelis-Menten constants (kcat, KM, and kcat/KM for 129 designed mutants of a glycoside hydrolase. Statistical analyses reveal that functional Tm is independent of kcat, KM, and kcat/KM in this system, illustrating that an individual mutation can modulate these functional parameters independently. In addition, this data set is used to evaluate computational predictions of protein stability using the established Rosetta and FoldX algorithms. Predictions for both are found to correlate only weakly with experimental measurements, suggesting improvements are needed in the underlying algorithms.

  20. Hydroxyzine- and cetirizine-loaded liposomes: effect of duration of thin film hydration, freeze-thawing, and changing buffer pH on encapsulation and stability.

    Science.gov (United States)

    Elzainy, Abeer A W; Gu, Xiaochen; Simons, F Estelle R; Simons, Keith J

    2005-03-01

    To assess the effect of the duration of film hydration, freeze-thawing, and changing buffer pH on the extent of entrapment of hydroxyzine and cetirizine, H1-antihistamines with different polarity, into liposomes, and the stability of these liposomes. Multilamellar vesicles (MLV) were prepared by thin-lipid film hydration using L-alpha-phosphatidylcholine (PC) and buffer containing 80 mg hydroxyzine at pH 7. For MLV containing hydroxyzine, the liposomes were subjected to 1) hydration for 1 h, 24 h, or 48 h for the control batch, batch B, or batch D respectively; and 2) hydration for 1 h, 24 h, or 48 h with freeze-thawing for 5-cycles for batch A, batch C, or batch E, respectively. These formulations were stored at 10 +/- 2 degrees C and 37 +/- 0.1 degrees C. Small unilamellar vesicles (SUV) and MLV were prepared using L-alpha-phosphatidylcholine (PC), and buffer at pH 5.0, 5.5, 6.0, 6.5, and 7.0, containing 80 mg hydroxyzine or 82 mg cetirizine by the ethanol injection and thin-lipid film hydration methods, respectively. These formulations were stored at 10 +/- 2 degrees C. Liposomes were evaluated immediately after preparation and after storage by determining percent entrapment of hydroxyzine (PETH) or of cetirizine (PEC) and by observing changes in the physical appearance (PA). Particle size (PSA) of the liposomes freshly prepared at pH=6.5 was measured from transmission electron micrographs (TEM). Increasing thin-film hydration time or repeated freeze-thawing did not affect the initial PETH or long-term stability of control, A, B, C, D, and E batches of MLV containing hydroxyzine stored at 10 +/- 2 degrees C. At 37 +/- 0.1 degrees C, PETH of all MLV batches decreased considerably after 1 month. This was more evident in batches B, C, and E exposed to freeze-thawing. The PETH of SUV increased markedly from 53.0% to 84.0% when the pH of the buffer was increased from 5.0 to 5.5. As pH increased from 6.0 to 7.0, PETH continued to increase from 84% to 94%. The initial

  1. Improvement of thermal stability of polypropylene using DOPO-immobilized silica nanoparticles.

    Science.gov (United States)

    Dong, Quanxiao; Ding, Yanfen; Wen, Bin; Wang, Feng; Dong, Huicong; Zhang, Shimin; Wang, Tongxin; Yang, Mingshu

    2012-09-01

    After the surface silylation with 3-methacryloxypropyltrimethoxysilane, silica nanoparticles were further modified by 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO). The immobilization of DOPO on silica nanoparticles was confirmed by Fourier transform infrared spectroscopy, UV-visible spectroscopy, magic angle spinning nuclear magnetic resonance, and thermogravimetric analysis. By incorporating the DOPO-immobilized silica nanoparticles (5 wt%) into polypropylene matrix, the thermal oxidative stability exhibited an improvement of 62 °C for the half weight loss temperature, while that was only 26 °C increment with incorporation of virgin silica nanoparticles (5 wt%). Apparent activation energies of the polymer nanocomposites were estimated via Flynn-Wall-Ozawa method. It was found that the incorporation of DOPO-immobilized silica nanoparticles improved activation energies of the degradation reaction. Based on the results, it was speculated that DOPO-immobilized silica nanoparticles could inhibit the degradation of polypropylene and catalyze the formation of carbonaceous char on the surface. Thus, thermal stability was significantly improved.

  2. Rheology, Mechanical Properties, and Thermal Stability of Maleated Polyethylene Filled with Nanoclays

    Directory of Open Access Journals (Sweden)

    Abdulhadi A. Al-Juhani

    2015-01-01

    Full Text Available Maleated polyethylene (MAPE was used in this study as a model matrix for hosting hydrophobic nanoclay (C15A and hydrophilic nanoclay (C30B, to investigate the effect of nanoclay loading on the bulk properties of the composites. Composites were prepared by melt-blending technique, with varying the loading from 0 to 9 wt.%. Tensile, oxidative TGA, and FE-SEM tests were employed for both C15A-filled polymer and C30B-filled polymer, which confirmed that C15A had better dispersion and was much superior to C30B for enhancing the mechanical properties and thermal stability of MAPE. Consequently, XRD and melt rheology tests were performed for C15A-filled polymer only. XRD confirmed the formation of nanocomposite structure, which could be the main reason for the significant increase in the thermal stability and viscosity. For example, compared to the neat polymer, the degradation temperature at the 20% mass loss was increased by 72°C after the addition of 5 wt.% C15A. Based on rheological analysis, the percolation threshold was around 3 wt.% loading of C15A. Fitting the viscosity data to the Cross model suggested that increasing C15A loading had a strong effect for increasing the shear thinning index and relaxation time of the nanocomposites.

  3. Gas uptake and thermal stability analysis of boron nitride and carbon nanotubes

    Science.gov (United States)

    Guan, Mengyu

    Carbon nanotubes (CNTs) exist in many forms and can have critical pore diameters on the angstrom length scale, making them suitable for molecular capture. By combining the porous structure of CNTs with the chemical stability of carbide and/or nitride materials, one can create a more robust, nanoporous material for gas capture in high temperature conditions. Boron nitride nanotubes (BNNTs) are more chemically and thermally robust than pure CNTs, and were synthesized using CNTs as a structural precursor. However, this reaction mechanism was found to be unfavorable to produce high-yield and purity BNNTs. Adsorption tests using gases of interest (N2, He) were performed on commercial CNTs and BNNTs to determine their porosity and gas uptake abilities. Their thermal stability and oxidation resistance when heated up to 1773 K in air was also studied using differential scanning calorimetry and thermogravimetric analysis. While the CNTs began to oxidize between 450 °C and 750 °C, depending on the nanotube diameter, the BNNTs remained stable up until 1000 °C.

  4. Thermal stability and dielectric properties of nano-SiO2-doped cellulose

    Science.gov (United States)

    Zhang, Song; Tang, Chao; Hao, Jian; Wang, Xiaobo

    2017-07-01

    We report the thermal stability and dielectric properties of nano-SiO2-doped cellulose. Molecular dynamics simulations were performed using an undoped cellulose model (C0), a nano-SiO2-doped cellulose model with untreated surface unsaturated bonds (C1), and a nano-SiO2-doped cellulose model for which surface unsaturated O atoms were treated with -H and surface unsaturated Si atoms were treated with -OH (C2). The simulation results showed that the mechanical properties of C1 and C2 were better than those of C0 and were optimal when the content of nano-SiO2 was 5%. The simulation results for C2 were more accurate than those for the other models, and thus, C2 provides theoretical support for the construction of a reasonable model of nano-SiO2 and cellulose in the future. The temperature at which the free volume fraction of C2 jumps was 50 K higher than that for C0, and the thermal stability of C2 was better than that of C0. Experimental results showed that the maximum tensile strength of the insulation paper was obtained when the content of nano-SiO2 was 5%. Moreover, at this content of nano-SiO2, the dielectric constant was lowest and closest to that of transformer insulation oil, which will improve the distribution of the electric field and thus the overall breakdown performance of oil-paper insulation systems.

  5. Lyapunov stability and Poisson structure of the thermal TDHF and RPA equations

    International Nuclear Information System (INIS)

    Veneroni, M.; Balian, R.

    1989-01-01

    The thermal TDHF equation is analyzed in the Liouville representation of quantum mechanics, where the matrix elements of the single-particle (s.p.) density ρ behave as classical dynamical variables. By introducing the Lie-Poisson bracket associated with the unitary group of the s.p. Hilbert space, we show that TDHF has a hamiltonian, but non-canonical, classical form. Within this Poisson structure, either the s.p. energy or the s.p. grand potential Ω(ρ) act as a Hamilton function. The Lyapunov stability of both the TDHF and RPA equations around a HF state then follows, since the HF approximation for thermal equilibrium is determined by minimizing Ω(ρ). The RPA matrix in the Liouville space is expressed as the product of the Poisson tensor with the HF stability matrix, interpreted as a metric tensor generated by the entropy. This factorization displays the roles of the energy and entropy terms arising from Ω(ρ) in the RPA dynamics, and it helps to construct the RPA modes. Several extensions are considered

  6. Stability of Oligosaccharides Derived from Lactose and Lactulose regarding Rheological and Thermal Properties

    Directory of Open Access Journals (Sweden)

    Sara López-Sanz

    2018-01-01

    Full Text Available Prebiotic carbohydrates derived from lactulose (OsLu are appealing ingredients that provide beneficial effects following their fermentation by the gut microbiota; however, more investigation is needed to evaluate their technological properties and applicability as a functional food ingredient in the market. In this paper, a comparative study on the rheological and thermal behavior of OsLu and a commercial mixture of galactooligosaccharides (GOS was carried out. In both cases, there was a strong influence of temperature and shear rate on viscosity. Viscosity of OsLu was higher than that of commercial GOS and variations and rheopexy cycles were also higher for OsLu. The exponential increase of viscosity associated with the structural changes took place later in OsLu than in commercial GOS, suggesting more stability to the shear over time in the former. More stability of OsLu was also observed in the study of the effect of temperature on viscosity. In addition, the thermal study indicated different behavior of both prebiotics under the assayed conditions, showing that OsLu have lower values of glass transition temperature (Tg than commercial GOS and that commercial GOS are more sensible against humidity. The results here obtained provide important information on the treatment and storage conditions of these prebiotic ingredients during the elaboration of functional foods.

  7. Dark and background response stability for the Landsat 8 Thermal Infrared Sensor

    Science.gov (United States)

    Vanderwerff, Kelly; Montanaro, Matthew

    2012-01-01

    The Thermal Infrared Sensor (TIRS) is a pushbroom sensor that will be a part of the Landsat Data Continuity Mission (LDCM), which is a joint mission between NASA and the USGS. The TIRS instrument will continue to collect the thermal infrared data that are currently being collected by the Thematic Mapper and the Enhanced Thematic Mapper Plus on Landsats 5 and 7, respectively. One of the key requirements of the new sensor is that the dark and background response be stable to ensure proper data continuity from the legacy Landsat instruments. Pre launch testing of the instrument has recently been completed at the NASA Goddard Space Flight Center (GSFC), which included calibration collects that mimic those that will be performed on orbit. These collects include images of a cold plate meant to simulate the deep space calibration source as viewed by the instrument in flight. The data from these collects give insight into the stability of the instrument’s dark and background response, as well as factors that may cause these responses to vary. This paper quantifies the measured background and dark response of TIRS as well as its stability.

  8. Thermal stability of a Co/Cu giant magnetoresistance (GMR) multilayer system

    Energy Technology Data Exchange (ETDEWEB)

    Vovk, V., E-mail: vitaliy.vovk@materials.ox.ac.uk [Department of Materials, University of Oxford, Parks Road, Oxford OX1 3PH (United Kingdom); Schmitz, G. [Institut fuer Materialphysik, Westf. Wilhelms-Universitaet Muenster, Wilhelm-Klemm-Str. 10, 48149 Muenster (Germany)

    2009-04-15

    Critical limitations exist regarding the thermal stability of multilayer giant magnetoresistance (GMR) sensors due to significant contribution of layer interfaces and grain boundaries to their performance. This paper addresses the stability of, and thermal reaction in Co/Cu magnetoresistive systems. Thin film multilayers were deposited by ion beam sputtering on top of preformed tungsten tips. The multilayers were then analyzed by a wide-angle tomographic atom probe (WATAP) in the as-prepared state and after heat treatments in the temperature range from 150 to 550 {sup o}C. As revealed by the WATAP analysis, Co breakthroughs along grain boundaries in the Cu spacers appear at 450 {sup o}C. This morphological change leads to a deterioration of the GMR effect due to the magnetostatic ferromagnetic coupling between Co layers. Furthermore, a strong effect of Cu layers faceting is observed after annealing in the same temperature range, which may lead to the deterioration of the layered structure on high-angle grain boundaries.

  9. Thermal stability of bimodal microstructure in magnesium alloy AZ91 processed by ECAP

    Energy Technology Data Exchange (ETDEWEB)

    Pantělejev, Libor, E-mail: pantelejev@fme.vutbr.cz [Institute of Materials Science and Engineering, Faculty of Mechanical Engineering, Brno University of Technology, Technická 2896/2, 616 69 Brno (Czech Republic); NETME Centre, Faculty of Mechanical Engineering, Brno University of Technology, Technická 2896/2, 616 69 Brno (Czech Republic); Štěpánek, Roman [Institute of Materials Science and Engineering, Faculty of Mechanical Engineering, Brno University of Technology, Technická 2896/2, 616 69 Brno (Czech Republic); NETME Centre, Faculty of Mechanical Engineering, Brno University of Technology, Technická 2896/2, 616 69 Brno (Czech Republic); Man, Ondřej [Institute of Materials Science and Engineering, Faculty of Mechanical Engineering, Brno University of Technology, Technická 2896/2, 616 69 Brno (Czech Republic)

    2015-09-15

    The changes in microstructure of equal channel angular pressing (ECAP) processed magnesium alloy AZ91 during thermal exposure were studied in this paper. The microstructure stability was investigated by means of electron backscatter diffraction (EBSD), which allowed to measure the changes in grain size, mutual ratio of low-angle boundaries (LABs) to high-angle ones (HABs) and local lattice distortion evaluated by the kernel average misorientation (KAM) parameter. It was found experimentally that the threshold temperature at which significant grain coarsening takes place is 350 °C. No modification to mean grain diameter occurs below this temperature, nonetheless, some changes in LAB and HAB fraction, as well as in local lattice distortion, can be observed. - Highlights: • Thermal stability of bimodal UFG AZ91 alloy was assessed by means of EBSD. • Threshold temperature for pronounced grain coarsening was found at 350 °C. • Below 350 °C increase in LAB fraction and local lattice distortion takes place. • Local lattice distortion (LLD) can be well described using KAM approach. • LLD is influenced by coarsening and precipitation of Mg{sub 17}Al{sub 12} particles.

  10. Acid-base synergistic flame retardant wood pulp paper with high thermal stability.

    Science.gov (United States)

    Wang, Ning; Liu, Yuansen; Xu, Changan; Liu, Yuan; Wang, Qi

    2017-12-15

    Acid-catalytic degradation caused by acid source flame retardants is the main reason for a decline in thermal stability of flame-retarded lignocellulosic materials. In the present research, a guanidine phosphate (GP)/borax (BX) flame retardant system based on acid-base synergistic interaction was designed and used in wood pulp paper (WPP) to solve this problem. Results showed that the treated WPP obtained good flame retardancy with a limiting oxygen index (LOI) value of 35.7%. As a basic flame retardant, borax could chemically combine with the acids released by guanidine phosphate, thus decreasing the acidity of the system in the initial heating stage. In this way, acid-catalytic degradation is greatly retarded on the lignocelluloses to improve thermal stability (the temperature of maximum degradation peak from 286°C to 314°C). Meanwhile, borax was also advantageous to form a denser and firmer condensed phase through reinforcement of the acid-base reaction product, borophosphates, allowing it to provide a protective barrier with higher quality. Copyright © 2017 Elsevier Ltd. All rights reserved.

  11. Thermal stability against reduction of LaMn1-yCoyO3 perovskites

    International Nuclear Information System (INIS)

    Pecchi, Gina; Campos, Claudia; Pena, Octavio

    2009-01-01

    Thermal and reduction-oxidation stability of substituted LaMn 1-y Co y O 3 perovskite-type oxides (0.0 ≤ y Co ≤ 1.0) prepared by the citrate route have been studied by means of surface area, X-ray diffraction, FTIR spectroscopy and magnetic properties. The perovskite orthorhombic structure is found for y Co ≤ 0.5, with the exception of y Co = 0.1, which corresponds better to rhombohedral LaMnO 3.15 . For y Co > 0.5 the diffraction profiles are quite similar to the cobaltite's rhombohedral structure. Magnetic iso-field studies (ZFC-FC) reveal that, for y Co ≤ 0.50, the system presents an antiferromagnetic canted-like ordering of the Mn/Co sublattice, in which the presence of divalent Co ion creates Mn 3+ -Mn 4+ pairs that interact ferromagnetically through the oxygen orbital. This interpretation is confirmed by the magnetization loops, in which the magnetic moment increases when substituting Mn for Co. Therefore, the general trend is: for y Co ≤ 0.5, the Co ions are inserted in the manganite structure and for y Co > 0.5, the Mn ions are inserted in cobaltite structure. The enhancement of the ferromagnetic properties and the thermal stability against reduction for y Co = 0.5 is attributed to optimized Co 2+ -Mn 4+ interactions

  12. Thermal stability of Pd Schottky contacts to p-type 6H-SiC

    Energy Technology Data Exchange (ETDEWEB)

    Samiji, M.E.; Leitch, A.W.R. [Dept. of Physics, Univ. of Port Elizabeth (South Africa); Venter, A. [Dept. of Physics, Vista Univ., Port Elizabeth (South Africa)

    2003-07-01

    The thermal stability of palladium (Pd) Schottky barrier diodes fabricated on bulk p-type Al-doped (5-8 x 10{sup 17} cm{sup -3}) 6H-SiC is reported. Isochronal anneals revealed a steady improvement in the as-deposited Pd contacts for temperatures up to 250-300 C, above which the quality progressively deteriorated. Above 600 C the contacts became unusable. The effect of hydrogen on the Pd Schottky diode was investigated by exposing the Pd metallized surface of the SiC to a hydrogen plasma. It was found that Pd became permeable to hydrogen around 250 C, resulting in a subsequent introduction of hydrogen into the near-surface region of the SiC. Capacitance-voltage (C-V) depth profiles of the H-plasma exposed diodes revealed a partial reduction in the near-surface free carrier concentration, suggesting passivation of the Al acceptors by hydrogen. This was confirmed by subsequent reactivation of the electrical activity of the Schottky contact through a series of isothermal reverse bias annealing experiments. Hydrogen was also found to improve the thermal stability of the Pd Schottky diode. (orig.)

  13. Influence of iron on crystallization behavior and thermal stability of the insulating materials - porous calcium silicates

    DEFF Research Database (Denmark)

    Haastrup, Sonja; Yu, Donghong; Yue, Yuanzheng

    2017-01-01

    The properties of porous calcium silicate for high temperature insulation are strongly influenced by impurities. In this work we determine the influence of Fe3+ on the crystallization behavior and thermal stability of hydrothermally derived calcium silicate. We synthesize porous calcium silicate...... by XRD analysis. The thermal stability and compressive strength of the calcium silicates are seriously influenced by the changes of their crystal structure. Linear shrinkage of the reference sample is 1.3% at 1050°C, whereas the sample with Fe/Si =1.0% does by 30.4%. In conclusion, the presence of Fe3...... measurements reveal a pronounced decrease in the number of Q3 sites in the calcium silicate with an increase of Fe3+, and thereby lower the crystal fraction of xonotlite (Ca6Si6O17(OH)2) phase, and increase the crystal fractions of tobermorite(Ca5Si6O16(OH)2·4H2O) and calcite (CaCO3) phases, as confirmed...

  14. Large thermally induced nonlinear refraction of gold nanoparticles stabilized by cyclohexanone

    Energy Technology Data Exchange (ETDEWEB)

    Sarkhosh, Leila; Aleali, Hoda; Karimzadeh, Rouhollah; Mansour, Nastaran [Physics Department, Shahid Beheshti University, Evin 19839, Tehran (Iran, Islamic Republic of)

    2010-10-15

    Stabilized gold nanoparticle (AuNP) colloids have been fabricated by nanosecond pulsed laser ablation of a pure gold plate in cyclohexanone. The AuNPs colloid exhibits a UV-Vis absorption spectrum with a surface plasmon absorption peak at about 540 nm. Scanning electron microscopy has shown the formation of spherical AuNPs with average size about 53 nm. The shift of 24 cm{sup -1} is observed in the carbonyl band of the colloid using FTIR spectroscopy. This shift indicates that the monomer carbonyl group of cyclohexanone interacts with the surface of the AuNPs and leads to stabilizing the colloid. A large nonlinear refractive index of -2.92 x 10{sup -7} cm{sup 2}/W is measured using the Z-scan technique under continuous wave laser irradiation at 532 nm. Our results show that the large induced nonlinear refraction is attributed to the surface plasmon resonance (SPR) enhancement effect of AuNPs, high thermo-optic coefficient and low thermal conductivity of cyclohexanone. Observation of far-field diffraction ring patterns confirm a thermally induced negative lens effect and spatial self-phase modulation in the laser beam as it traverses the colloids. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

  15. Thermal stability and structural changes during heat treatment of nanostructured Al2024 alloy

    Energy Technology Data Exchange (ETDEWEB)

    Jafari, M. [Department of Materials Engineering, Isfahan University of Technology, Isfahan 84156-83111 (Iran, Islamic Republic of); Enayati, M.H. [Department of Materials Engineering, Isfahan University of Technology, Isfahan 84156-83111 (Iran, Islamic Republic of)], E-mail: ena78@cc.iut.ac.ir; Abbasi, M.H.; Karimzadeh, F. [Department of Materials Engineering, Isfahan University of Technology, Isfahan 84156-83111 (Iran, Islamic Republic of)

    2009-06-10

    Thermal stability and structural changes during isothermal heat treatment of nanostructured Al2024 alloy prepared by mechanical milling (MM) were investigated. Al2024 powders were subjected to high-energy milling for various times to produce nanostructured alloy. Nanostructured Al2024 alloy was subsequently annealed at 150-550 deg. C for 1-3 h under argon atmosphere. The as-milled and annealed powders were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results showed that after 30 h of milling, an Al-Cu-Mg supersaturated solid solution with a grain size of 30 nm was obtained. This structure was then isothermally heat-treated at various temperatures for different times. The CuAl{sub 2} and CuMgAl{sub 2} precipitates formed after heat treatment at T < 350 deg. C. In contrast to CuAl{sub 2} phase, CuMgAl{sub 2} precipitates disappeared on XRD traces taken after annealing at temperatures higher than 350 deg. C. Investigation of grain growth kinetics showed that nanostructured Al2024 had high thermal stability so that Al grain size remained in nanosized scale (about 70 nm) even after heating at 550 deg. C for 3 h. The value of grain growth exponent and activation energy at different annealing temperatures were obtained and discussed in terms of solute and second phase drag effects.

  16. Morphology and thermal stability of silk fibroin/starch blended microparticles

    Directory of Open Access Journals (Sweden)

    2010-12-01

    Full Text Available In the present study biodegradable microparticles of silk fibroin (SF/starch blends were prepared by a simple water-in-oil emulsion solvent diffusion technique. SF/starch blended solution and ethyl acetate were used as water and oil phases, respectively. The influence of SF/starch ratios on characteristics of the blended microparticles was investigated. The SF conformation of microparticle matrices from FTIR analysis was changed from random coil to β-sheet form by blending with starch. The blended microparticles had lower dissolution in water than those of SF and starch microparticles. The 1/3 (w/w SF/starch blended microparticles exhibited the lowest dissolution. The SF and starch microparticles showed irregular and deflated shapes, respectively. The blended microparticles were nearly spherical in shapes and smaller sizes. Thermal stability of the blended microparticles slightly increased with the starch blended ratio. The results suggested that SF conformational transition, thermal stability, morphology and dissolution of the blended microparticles can be adjusted by varying the blended ratio.

  17. Electrodeposited nanocrystalline Co-P alloys: Microstructural characterization and thermal stability

    International Nuclear Information System (INIS)

    Silva, M. da; Wille, C.; Klement, U.; Choi, P.; Al-Kassab, T.

    2007-01-01

    Nanocrystalline Co-P has a significantly increased thermal stability compared to other nanocrystalline Ni- and Co-based electrodeposits. By combining observations from transmission electron microscopy in situ annealing with differential scanning calorimetry and tomographic atom probe measurements, the microstructural development of nanocrystalline Co-1.1 at.% P and Co-3.2 at.% P is described. In the as-prepared state, both alloys consist of 10 nm sized hcp-Co grains, and the P-distribution is already inhomogeneous. Upon annealing, P-atoms segregate to the grain boundaries, and grain growth takes place. Initial grain growth is abnormal in both electrodeposits, but occurs slower and more homogeneously in Co-3.2 at.% P. When P-saturation of the grain boundaries is reached, P-rich precipitates form accompanied by rapid (normal) grain growth. Due to the higher initial P-concentration in Co-3.2 at.% P, saturation of P and precipitation occurs earlier leading to a slightly lower thermal stability. Apart from the different P-contents, the effect of impurities, allotropic phase transformation of Co and texture is discussed

  18. Nucleating Effect of Carbon Nanoparticles and Their Influence on the Thermal and Chemical Stability of Polypropylene

    Directory of Open Access Journals (Sweden)

    F. Avalos-Belmontes

    2012-01-01

    Full Text Available The effect of carbon nanofibers (CNFs and carbon nanotubes (CNTs on the thermal and chemical stability of polypropylene (PP when subjected to oxidation in a strong acid medium was studied. The effect of CNFs and CNTs on the crystalline morphology and the melting and crystallization temperatures was also studied. The thermal stability increased markedly; the decomposition temperature, for example, increased from 293∘C for pure PP to 312 and 320∘C for PP with CNFs and CNTs, respectively. The crystallization temperature increased perceptibly with the addition of CNTs or CNFs, from 107∘C for pure PP to 112 and 114∘C for PP with CNFs and CNTs, respectively. The oxidative degradation with nitric acid produced a reduction in molecular weight; however, this negative effect was less pronounced in the PP compositions with carbon nanoparticles. After 8 hours in nitric acid, this reduction was from 141,000 to 68,000 (for pure PP, to 75,000 (for PP-CNFs, and 79,500 (for PP-CNTs. X-ray diffraction showed that the alpha type crystallinity remains, irrespective of the nucleating agent. Finally, the intensity ratio between the (040 (at 16.7∘ and the (110 (at 13.9∘ reflections increased, which was taken as an indication of an increasing nucleating efficiency.

  19. Synthesis and Thermal-Stability Study of Polybutylene Itaconate Modified with Divinyl Benzene and Glycerol

    Directory of Open Access Journals (Sweden)

    Atmanto Heru Wibowo

    2014-10-01

    Full Text Available Polybutylene itaconate (PBI for modification with divinyl benzene (DVB and glycerol has been synthesized at 180 °C for 3 h via polycondensation of itaconic acid (IA and butanediols using catalyst of Ti(OBu4. Modification on PBI was done with addition of 15%, 20% and 25% DVB (w/w using benzoyl peroxide. With glycerol, weight variations of glycerol:1,4-butanediol (BDO in the synthesis were 10%, 30%, and 50% (mole/mole. PBI and PBI modified with DVB and glycerol were characterized with FTIR and TG-DTA. PBI showed a wavenumber shift from 1703 cm-1 to 1728 cm-1 of the C=O functional group from acid to esther. The DVB modification on PBI also showed that the intensity decrease of C=C stretching was due to the formation of crosslinking on the double bond. In the modification with glycerol, three dimensional networking on the polyester occurred through bonding between hydroxyl of glycerol and acid group of IA. Constant intensity of C=C stretching on polyester was seen. The thermal stability of PBI modified with DVB increased, accompanied by rigidity change of the structure. The thermal stability of PBI modified with glycerol decreased, caused by the decrease of regularity degree and the elasticity increase of the three dimensional structure of polyester.

  20. Correlation between Thermal Treatment and Phase Transformation in Nanocrystalline Stabilized Zirconia

    Directory of Open Access Journals (Sweden)

    Tajudeen Oladele AHMED

    2013-06-01

    Full Text Available Stabilized zirconia produced via wet chemistry has chemically higher uniformity and purity. However, the grain size, particle shape, agglomerate size and specific surface area can be modified within certain degree by controlling the precipitation and sintering conditions. Generally, any physical or chemical difference between phases or effect occurring on the appearance or disappearance of a phase can be determined via thermal analysis and X-ray Diffractometry coupled with electron microscopy. In the last few decades, these materials have received tremendous attention globally in the field of defect solid-state devices. However, the challenge in this field of research has been to study thermal behaviour of these electrolytes during phase transformations and develop improved electrolytes with low activation temperature in the range of 600°C-800°C. In this paper, we report the wet chemistry of bismuth oxide stabilized zirconia having high experimental yield and low transformation temperature. Thus, the phase transformation from amorphous Zirconia to monoclinic is reported to begin above 600oC to an optimum temperature of 700oC. After calcination at 800oC for 4h, the powder have narrow particle size distribution in the range of 63-101µm. The average crystallite sizes of the synthesized powders range from 8-33nm.

  1. THERMAL STABILITY STUDY OF DIAMOND-LIKE CARBON FILMS CONTAINING CRYSTALLINE DIAMOND NANOPARTICLES

    Directory of Open Access Journals (Sweden)

    Beatriz Campos Ramos

    2014-08-01

    Full Text Available Nanocrystalline diamond (NCD particles are incorporated into diamond-like carbon (DLC films in order to prevent NCD-DLC electrochemical corrosion. In the current paper, the thermal stability of these films was investigated. The NCD-DLC films were deposited on 316L stainless steel substrates using plasma enhanced chemical vapor deposition. The grain size of the diamond crystallites and their concentration were varied in order to obtain different NCD-DLC films. The samples were annealed to 50°C for 1 h. The annealing temperature increased until the complete graphitization of the films (ramp of 50°C. Raman scattering spectroscopy was used to evaluate in detail the chemical structure of the DLC and NCD-DLC films. The atomic arrangements and graphitization level according to the increasing temperature are discussed. The influence of NCD particle sizes and concentration on NCD-DLC thermal stability are also discussed. The results showed that the presence of crystalline diamond particles increased the graphitization temperature, which permits the use of NCD-DLC films in high temperature environments.

  2. Update of S-NPP VIIRS Thermal Emissive Bands Radiometric Calibration Stability Monitoring Using the Moon

    Science.gov (United States)

    Wang, Zhipeng; Xiong, Xiaoxiong; Li, Yonghong

    2016-01-01

    The Suomi-NPP VIIRS thermal emissive bands (TEB) are radiometrically calibrated on-orbit with reference to an onboard blackbody (BB) regularly operated at approximately 292.5 K. The calibration stability at other temperature ranges can be evaluated based on the observations of remote targets with stable thermal properties, such as the Moon. VIIRS has scheduled viewings of the Moon on a nearly monthly basis at a phase angle of nearly -51 degrees. In this study, the brightness temperatures (BT) of the lunar surface retrieved using the detector gain coefficients calibrated with the BB are trended to monitor the calibration stability of VIIRS TEB. Since the Lunar surface temperatures are spatially non-uniform and vary greatly with the photometric geometry, the BT trending must be based on the same regions of the Moon under the same solar illumination condition. Also, the TEB lunar images are always partially saturated because the highest lunar surface temperatures are beyond the dynamic range of all VIIRS TEB detectors. Therefore, a temporally invariant dynamic mask is designed to clip a fraction of the lunar images corresponding to the regions of the Moon that may saturate the detector at any lunar event. The BT of the remaining hottest pixels are then trended. Results show that, since the launch of VIIRS to mid-2016, the radiometric calibration of all TEB detectors has been stable within 0.4 K at the BT range of as high as 350 K.

  3. Thermal Stability of Silver Paste Sintering on Coated Copper and Aluminum Substrates

    Science.gov (United States)

    Pei, Chun; Chen, Chuantong; Suganuma, Katsuaki; Fu, Guicui

    2018-01-01

    The thermal stability of silver (Ag) paste sintering on coated copper (Cu) and aluminum (Al) substrates has been investigated. Instead of conventional zincating or nickel plating, magnetron sputtering was used to achieve coating with titanium (Ti) and Ag. Silicon (Si) chips were bonded to coated Cu and Al substrates using a mixture of submicron Ag flakes and particles under 250°C and 0.4 MPa for 30 min. The joints were then subject to aging testing at 250°C for duration of 200 h, 500 h, and 1000 h. Two types of joints exhibited satisfactory initial shear strength above 45 MPa. However, the shear strength of the joints on Al substrate decreased to 28 MPa after 1000 h of aging, while no shear strength decline was detected for the joints on Cu substrate. Fracture surface analysis revealed that the vulnerable points of the two types of joints were (1) the Ag layer and (2) the interface between the Ti layer and Cu substrate. Based on the results of scanning electron microscopy (SEM), energy-dispersive x-ray spectroscopy (EDS), and simulations, cracks in the Ag layer were identified as the cause of the shear strength degradation in the joints on Al substrate. The interface evolution of the joints on Cu substrate was ascribed to Cu migration and discontinuity points that initialized in the Ti layer. This study reveals that Al exhibited superior thermal stability with sintered Ag paste.

  4. Thermal Stability of Copper-Aluminum Alloy Thin Films for Barrierless Copper Metallization on Silicon Substrate

    Science.gov (United States)

    Wang, C. P.; Dai, T.; Lu, Y.; Shi, Z.; Ruan, J. J.; Guo, Y. H.; Liu, X. J.

    2017-08-01

    Copper thin films with thickness of about 500 nm doped with different aluminum concentrations have been prepared by magnetron sputtering on Si substrate and their crystal structure, microstructure, and electrical resistivity after annealing at various temperatures (200°C to 600°C) for 1 h or at 400°C for different durations (1 h to 11 h) investigated by grazing-incidence x-ray diffraction (GIXRD) analysis, scanning electron microscopy (SEM), and four-point probe (FPP) measurements. Cu-1.8Al alloy thin film exhibited good thermal stability and low electrical resistivity (˜5.0 μΩ cm) after annealing at 500°C for 1 h or 400°C for 7 h. No copper silicide was observed at the Cu-Al/Si interface by GIXRD analysis or SEM for this sample. This result indicates that doping Cu thin film with small amounts of Al can achieve high thermal stability and low electrical resistivity, suggesting that Cu-1.8Al alloy thin film could be used for barrierless Cu metallization on Si substrate.

  5. Mechanical synthesis of copper-carbon nanocomposites: Structural changes, strengthening and thermal stabilization

    International Nuclear Information System (INIS)

    Nunes, D.; Livramento, V.; Mateus, R.; Correia, J.B.; Alves, L.C.; Vilarigues, M.; Carvalho, P.A.

    2011-01-01

    Highlights: → The study characterized Cu-nanodiamond (Cu-nD) and Cu-graphite (Cu-G) composites. → Preservation of nD crystalline structure during high-energy milling was demonstrated. → Higher refinement of matrix in Cu-nD comparing to Cu-G is due to a milling mechanism. → Remarkable thermal stability and microhardness have been achieved in Cu-nD and Cu-G. → Strengthening resulted mainly from grain refinement and second-phase reinforcement. - Abstract: Processing of copper-carbon nanocomposites by mechanical synthesis poses specific challenges as carbon phases are prone to amorphization and exhibit an intrinsically difficult bonding with copper. The present work investigates Cu-nanodiamond (Cu-nD) and Cu-graphite (Cu-G) composites produced by mechanical synthesis and subsequent heat treatments. Transmission electron microscopy observations showed homogeneous particle distributions and intimate bonding between the metallic matrix and the carbon phases. Ring diffraction patterns of chemically extracted carbon phases demonstrated that milled nanodiamond preserved crystallinity, while an essentially amorphous nature could be inferred for milled graphite. Raman spectra confirmed that nanodiamond particles remained essentially unaffected by the mechanical synthesis, whereas the bands of milled graphite were significantly changed into the typical amorphous carbon fingerprint. Particle-induced X-ray emission spectroscopy showed that the total contamination originating from the milling media remained below 0.7 wt.%. The Cu-nanodiamond composite exhibited remarkable microhardness and microstructural thermal stability when compared with pure nanostructured copper.

  6. Mechanical synthesis of copper-carbon nanocomposites: Structural changes, strengthening and thermal stabilization

    Energy Technology Data Exchange (ETDEWEB)

    Nunes, D., E-mail: daniela.nunes@ist.utl.pt [Associacao Euratom/IST, Instituto de Plasmas e Fusao Nuclear - Laboratorio Associado, Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); LNEG, Estrada do Paco do Lumiar, 1649-038 Lisboa (Portugal); ICEMS, Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Livramento, V. [Associacao Euratom/IST, Instituto de Plasmas e Fusao Nuclear - Laboratorio Associado, Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); LNEG, Estrada do Paco do Lumiar, 1649-038 Lisboa (Portugal); Mateus, R. [Associacao Euratom/IST, Instituto de Plasmas e Fusao Nuclear - Laboratorio Associado, Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Correia, J.B. [LNEG, Estrada do Paco do Lumiar, 1649-038 Lisboa (Portugal); Alves, L.C. [ITN, Instituto Tecnologico e Nuclear, Estrada Nacional 10, 2686-953 Sacavem (Portugal); Vilarigues, M. [Departamento de Conservacao e Restauro e R and D Unit Vidro e da Ceramica Para as Artes, FCT-UNL, Quinta da Torre, 2829-516 Caparica (Portugal); Carvalho, P.A. [ICEMS, Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Departamento de Bioengenharia, Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal)

    2011-11-15

    Highlights: {yields} The study characterized Cu-nanodiamond (Cu-nD) and Cu-graphite (Cu-G) composites. {yields} Preservation of nD crystalline structure during high-energy milling was demonstrated. {yields} Higher refinement of matrix in Cu-nD comparing to Cu-G is due to a milling mechanism. {yields} Remarkable thermal stability and microhardness have been achieved in Cu-nD and Cu-G. {yields} Strengthening resulted mainly from grain refinement and second-phase reinforcement. - Abstract: Processing of copper-carbon nanocomposites by mechanical synthesis poses specific challenges as carbon phases are prone to amorphization and exhibit an intrinsically difficult bonding with copper. The present work investigates Cu-nanodiamond (Cu-nD) and Cu-graphite (Cu-G) composites produced by mechanical synthesis and subsequent heat treatments. Transmission electron microscopy observations showed homogeneous particle distributions and intimate bonding between the metallic matrix and the carbon phases. Ring diffraction patterns of chemically extracted carbon phases demonstrated that milled nanodiamond preserved crystallinity, while an essentially amorphous nature could be inferred for milled graphite. Raman spectra confirmed that nanodiamond particles remained essentially unaffected by the mechanical synthesis, whereas the bands of milled graphite were significantly changed into the typical amorphous carbon fingerprint. Particle-induced X-ray emission spectroscopy showed that the total contamination originating from the milling media remained below 0.7 wt.%. The Cu-nanodiamond composite exhibited remarkable microhardness and microstructural thermal stability when compared with pure nanostructured copper.

  7. Characteristics of thermal hydraulic stability in a HYPER system with enhanced natural circulation potential

    International Nuclear Information System (INIS)

    Tak, Nam Il; Park, Won S.; Han, Seok Jung

    1999-06-01

    Pb-Bi eutectic chosen as a coolant of HYPER is an excellent heat transfer medium but requires relatively large pumping power. Thus the mixed cooling concept to increase economy and safety is being considered for HYPER. In this cooling concept, a large fraction of total thermal power is carried by natural circulation. However, the mixed cooling concept has been considered for conceptual designs only an it has never been applied to real reactors. The purpose of the present study is to provide simple tools to analyze mixed flow and to examine fundamental stability characteristics of mixed flow. Conventional one-dimensional approaches using mass, momentum, and energy conservation are used to describe a forced circulating flow affected by a large buoyancy force. The results of simple analysis using preliminary design parameters of HYPER show that cooling by mixed flow is possible only when the total pressure loss of system is sufficiently low. The stability behavior of mixed flow in a simple rectangular loop has been studied using numerical solutions of the governing equations. As in the case of natural circulation, three types of flow regions, such as stable, neutrally stable, and unstable regions, were found. The stability map of mixed flow has been obtained using the results of calculations. Forced flow due to the pump is found to increase the stability of the loop, since the stable portion of the stability map is increased. However, the unstable region of the mixed flow does not completely disappear, even though the pump exists. (author). 37 refs., 4 tabs., 23 figs

  8. The Hemagglutinin-Esterase Fusion Glycoprotein Is a Primary Determinant of the Exceptional Thermal and Acid Stability of Influenza D Virus.

    Science.gov (United States)

    Yu, Jieshi; Hika, Busha; Liu, Runxia; Sheng, Zizhang; Hause, Ben M; Li, Feng; Wang, Dan

    2017-01-01

    Influenza D virus (IDV) is unique among four types of influenza viruses in that it utilizes cattle as a primary reservoir. The thermal and acid stability of IDV were examined and directly compared with those of influenza A virus (IAV), influenza B virus (IBV), and influenza C virus (ICV). The results of our experiments demonstrated that only IDV had a high residual infectivity (~2.5 log units of 50% tissue culture infective dose [TCID 50 ]/ml) after a 60-min exposure to 53°C in solution at a neutral pH, and remarkably, IDV retained this infectivity even after exposure to 53°C for 120 min. Furthermore, the data showed that IDV was extremely resistant to inactivation by low pH. After being treated at pH 3.0 for 30 min, IDV lost only approximately 20% of its original infectiousness, while all other types of influenza viruses were completely inactivated. Finally, replacement of the hemagglutinin (HA) and neuraminidase (NA) proteins of a temperature- and acid-sensitive IAV with the hemagglutinin-esterase fusion (HEF) protein of a stable IDV through a reverse genetic system largely rendered the recombinant IAVs resistant to high-temperature and low-pH treatments. Together, these results indicated that the HEF glycoprotein is a primary determinant of the exceptional temperature and acid tolerance of IDV. Further investigation into the viral entry and fusion mechanism mediated by the intrinsically stable HEF protein of IDV may offer novel insights into how the fusion machinery of influenza viruses evolve to achieve acid and thermal stability, which as a result promotes the potential to transmit across mammal species. IMPORTANCE Influenza D virus (IDV) utilizes cattle as a primary reservoir. Increased outbreaks in pigs and serological evidence of human infection have raised a concern about the potential of IDV adapting to humans. Here, we directly compared IDV's stability to that of other influenza types (A, B, and C) following prolonged incubation at high temperatures

  9. Best-estimate plus uncertainty thermal-hydraulic stability analysis of BWRs using TRACG code

    International Nuclear Information System (INIS)

    Vedovi, J.; Yang, J.; Klebanov, L.; Vreeland, D. G.; Zino, J. F.

    2012-01-01

    Over the last decade, Boiling Water Reactor (BWR) power up-rates have increased plant rated power output significantly. Subsequent projects have expanded flow domains (e.g. MELLLA+) for operation at these higher power levels. This has resulted in an increase in the power to flow ratio in regions susceptible to reactor thermal-hydraulic instabilities. Since BWRs are susceptible to coupled thermal-hydraulic/nuclear oscillations when operating at these conditions, such oscillations must be prevented or reliably detected and suppressed. The Detect and Suppress Solution - Confirmation Density (DSS-CD) is the most sophisticated GEH BWR instability protection system ever employed. DSS-CD implements algorithms that monitor closely-spaced groups of Local Power Range Monitor (LPRM) detectors to detect periodic behavior typical of reactor instability events. This system is able to detect small, localized power variations in the core, distinguish between true instabilities and plant noise, and trip/scram the reactor while maintaining adequate safety margins. The combination of hardware, software, and system setpoints provides protection against violation of the Safety Limit Minimum Critical Power Ratio (SLMCPR) for anticipated oscillations. To support DSS-CD implementation, the TRACG system code is used to simulate events to confirm the capability of the DSS-CD solution for early oscillation detection and suppression. TRACG is a GEH proprietary version of the Transient Reactor Analysis Code (TRAC). TRACG includes a multi-dimensional, two-fluid model for the reactor thermal-hydraulics and a three-dimensional reactor kinetics model. The models are qualified to simulate a large variety of tests and reactor configurations, including thermal-hydraulic stability events. These features allow for detailed, best-estimate simulation of a wide range of BWR phenomena. A set of integrated TRACG event simulations for reasonably limiting anticipated events can be used to calculate the effect

  10. Thermal stability and degradation of poly (N-phenylpropionamide homopolymer and copolymer of N-phenylpropionamide with methyl methacrylate

    Directory of Open Access Journals (Sweden)

    M.A. Diab

    2017-05-01

    Full Text Available Different concentrations of copolymer of (N-phenylpropionamide (PA with methyl methacrylate (MMA were prepared and the reactivity ratio values of copolymerization were calculated using the 1H-NMR technique. Thermal analysis of the copolymers showed that the thermal stability is an intermediate between poly(N-phenylpropionamide and poly(methyl methacrylate homopolymers. Thermal degradation products of the PPA were identified by GC–MS techniques. It seems that the mechanism of degradation of PPA homopolymer is characterized by free radical formation followed by recombination along the backbone chain. The activation energies of the thermal degradation of the copolymers were calculated using the Arrhenius relationship.

  11. Thermal stability of functional P(S-r-MMA) random copolymers for nanolithographic applications.

    Science.gov (United States)

    Sparnacci, Katia; Antonioli, Diego; Gianotti, Valentina; Laus, Michele; Zuccheri, Giampaolo; Ferrarese Lupi, Federico; Giammaria, Tommaso Jacopo; Seguini, Gabriele; Ceresoli, Monica; Perego, Michele

    2015-02-25

    Two strategies are envisioned to improve the thermal stability of the grafted layer and to allow the processing of the random copolymer/block copolymer (RCP/BCP) system at high temperature. From one side, a high-temperature thermal treatment of a commercial α-hydroxyl ω-2,2,6,6-tetramethylpiperidinyloxy functional RCP, namely, TR58, leads to the formation of a stabilized layer able to induce the perpendicular orientation of a symmetric BCP to temperatures higher than 310 °C. On the other side, an α-hydroxyl ω-Br functional RCP, namely, BrR58, with the same molar mass and composition of TR58, was prepared by activator regenerated by electron transfer atom transfer radical polymerization. The resulting brush layer can sustain the self-assembly of the symmetric BCP for processing temperatures as high as 330 °C. In both systems, the disruption of the BCP film, deposited on the grafted RCP layer, occurs because of the formation of bubbles, due to a low-temperature evolution of monomers from the RCP layer. The extent of the low-temperature monomer evolution is higher for TR58 than it is for BrR58 and starts at lower temperatures. For both copolymers, the thermal treatment offsets the low-temperature monomer evolution while still maintaining surface characteristics suitable to induce the perpendicular orientation of the BCPs, thus ultimately extending the range of processing temperatures of the BCP film and consequently speeding the self-organization process.

  12. Synergistic effect of silicate clay and phosphazene-oxyalkyleneamines on thermal stability of cured epoxies.

    Science.gov (United States)

    Chen, Yu-Min; Liao, Yi-Lin; Lin, Jiang-Jen

    2010-03-01

    Amine substitution of hexachlorocyclophosphazene (HCP) with poly(oxypropylene)diamines (POP) afforded HCP-POP adducts which were subsequently intercalated into a layered silicate clay. The relative thermal stabilities of the epoxies cured with the phosphazene-amines and the intercalated clays were studied. The organoclays, with the confined HCP-POP from 400 and 2000 g/mol M(w) amines, are nongelled products when using 1/6 M ratio of HCP/POP starting materials in tetrahydrofuran solvent. The intercalation of HCP-POP polyamine salts into sodium montmorillonite afforded the HCP-POP-embedded organoclays with an expanded interlayer silicate spacing (2.4-5.1 nm) from the original 1.2 nm spacing (X-ray diffraction). The effect of silicate clays was evaluated by blending the HCP-POP/clay hybrids into a two-component epoxy system (diglycidyl ether of 4,4'-isopropylidenediphenol (BPA) and a diamine) and fully cured to form solid materials. The distribution of the exfoliated silicate platelets in the matrix was analyzed by transmission electronic microscopy (TEM). Thermal gravimetric analysis (TGA) indicated an enhanced thermal stability for the HCP/clay epoxy nanocomposites, with a delayed weight-loss pattern (temperature of weight loss at 10% (T(10 wt.%)) from 360 to 385 degrees C and temperature of weight loss at 85% (T(85 wt.%)) from 598 to 696 degrees C), compared to the pristine epoxies. By comparing these epoxies with different amounts of phosphazene and/or silicates, the TGA revealed a synergistic effect for the presence of both phosphorous and silicate components. Furthermore, the epoxies had improved physical properties such as hardness (from 3H to 5H) and surface adhesion (observed by scanning electron microscope (SEM) on fracture surface). 2009. Published by Elsevier Inc. All rights reserved.

  13. Impact of alginate concentration on the stability of agglomerates made of TiO{sub 2} engineered nanoparticles: Water hardness and pH effects

    Energy Technology Data Exchange (ETDEWEB)

    Loosli, Frédéric, E-mail: frederic.loosli@unige.ch [University of Geneva, Section des Sciences de la Terre et de l’Environnement, Group of Environmental Physical Chemistry, F.-A. Forel Institute (Switzerland); Coustumer, Philippe Le, E-mail: philippe.le-coustumer@u-bordeaux1.fr [Université Bordeaux 3, EA 4592 Géoressources & Environnement, ENSEGID (France); Stoll, Serge, E-mail: serge.stoll@unige.ch [University of Geneva, Section des Sciences de la Terre et de l’Environnement, Group of Environmental Physical Chemistry, F.-A. Forel Institute (Switzerland)

    2015-01-15

    The stability of engineered nanoparticles in natural aquatic systems is of high interest for environmental risk assessment since an already important quantity of these reactive species is entering aquatic systems. In the present study, an important issue is addressed by investigating (i) the influence of divalent cations and water hardness (Mg{sup 2+} and Ca{sup 2+}) in agglomerate formation and (ii) alginate concentration effect on the stability TiO{sub 2} agglomerates formed in environmental freshwater conditions (pH and total hardness) representative of Lake Geneva, France/Switzerland. Our results indicate that the presence of alginate at typical natural organic matter concentration strongly modifies the stability of TiO{sub 2} nanoparticle agglomerates by inducing their partial disagglomeration. Significant TiO{sub 2} nanoparticles redispersion and formation of small fragments are expected to be induced by alginate adsorbed layer formed at the nanoparticle surfaces within the agglomerates.Graphical Abstract.

  14. Bis(triisopropylsilylethynyl)pentacene/Au(111) interface: Coupling, molecular orientation, and thermal stability

    KAUST Repository

    Gnoli, Andrea

    2014-10-02

    The assembly and the orientation of functionalized pentacene at the interface with inorganics strongly influence both the electric contact and the charge transport in organic electronic devices. In this study electronic spectroscopies and theoretical modeling are combined to investigate the properties of the bis(triisopropylsilylethynyl)pentacene (TIPS-Pc)/Au(111) interface as a function of the molecular coverage to compare the molecular state in the gas phase and in the adsorbed phase and to determine the thermal stability of TIPS-Pc in contact with gold. Our results show that in the free molecule only the acene atoms directly bonded to the ligands are affected by the functionalization. Adsorption on Au(111) leads to a weak coupling which causes only modest binding energy shifts in the TIPS-Pc and substrate core level spectra. In the first monolayer the acene plane form an angle of 33 ± 2° with the Au(111) surface at variance with the vertical geometry reported for thicker solution-processed or evaporated films, whereas the presence of configurational disorder was observed in the multilayer. The thermal annealing of the TIPS-Pc/Au(111) interface reveals the ligand desorption at ∼470 K, which leaves the backbone of the decomposed molecule flat-lying on the metal surface as in the case of the unmodified pentacene. The weak interaction with the metal substrate causes the molecular dissociation to occur 60 K below the thermal decomposition taking place in thick drop-cast films.

  15. Thermal characteristics of shape-stabilized phase change material wallboard with periodical outside temperature waves

    International Nuclear Information System (INIS)

    Zhou, Guobing; Yang, Yongping; Wang, Xin; Cheng, Jinming

    2010-01-01

    Thermal characteristics of shape-stabilized phase change material (SSPCM) wallboard with sinusoidal temperature wave on the outer surface were investigated numerically and compared with traditional building materials such as brick, foam concrete and expanded polystyrene (EPS). One-dimensional enthalpy equation under convective boundary conditions was solved using fully implicit finite-difference scheme. The simulation results showed that the SSPCM wallboard presents distinct characteristics from other ordinary building materials. Phase transition keeping time of inner surface and decrement factor were applied to analyze the effects of PCM thermophysical properties (melting temperature, heat of fusion, phase transition zone and thermal conductivity), inner surface convective heat transfer coefficient and thickness of SSPCM wallboard. It was found that melting temperature is one important factor which influences both the phase transition keeping time and the decrement factor; for a certain outside temperature wave, there exist critical values of latent heat of fusion and thickness of SSPCM above which the phase transition keeping time or the decrement factor are scarcely influenced; thermal conductivity of PCM and inner surface convective coefficient have little effect on the phase transition keeping time but significantly influence the decrement factor; and the phase transition zone leads to small fluctuations of the original flat segment of inner surface temperature line. The results aim to be useful for the selection of SSPCMs and their applications in passive solar buildings.

  16. Preparation of Graphene Oxide Stabilized Nickel Nanoparticles with Thermal Effusivity Properties by Laser Ablation Method

    Directory of Open Access Journals (Sweden)

    Amir Reza Sadrolhosseini

    2013-01-01

    Full Text Available Nickel nanoparticles were dispersed uniformly in a graphene oxide solution, using a laser ablation technique with different ablation times that ranged from 5 to 20 minutes. The results indicate that the nickel nanoparticle sizes inside the graphene oxide decreased, and the volume fraction for the nickel nanoparticles in the graphene oxide increased with an increasing ablation time. Further, using Fourier Transform Infrared Spectroscopy, the nickel nanoparticles in the graphene oxide demonstrate greater stability from possible agglomeration when the nanoparticle was capped with oxygen from the carboxyl group of the graphene oxide. The thermal effusivity of the graphene oxide and nickel nanoparticle graphene oxide composite was measured using a photoacoustic technique. The concentration of graphene oxide shifted from 0.05 mg/L to 2 mg/L, and the thermal effusivity increased from 0.153 W·s1/2·cm−2·K−1 to 0.326 W·s1/2·cm−2·K−1. In addition, the thermal effusivity of the nickel nanoparticles graphene oxide composite increased with an increase in the volume fraction of nickel nanoparticles from 0.1612 W·s1/2·cm−2·K−1 to 0.228 W·s1/2·cm−2·K−1.

  17. Numerical modelling of levee stability based on coupled mechanical, thermal and hydrogeological processes

    Directory of Open Access Journals (Sweden)

    Dwornik Maciej

    2016-01-01

    Full Text Available The numerical modelling of coupled mechanical, thermal and hydrogeological processes for a soil levee is presented in the paper. The modelling was performed for a real levee that was built in Poland as a part of the ISMOP project. Only four parameters were changed to build different flood waves: the water level, period of water increase, period of water decrease, and period of low water level after the experiment. Results of numerical modelling shows that it is possible and advisable to calculate simultaneously changes of thermal and hydro-mechanical fields. The presented results show that it is also possible to use thermal sensors in place of more expensive pore pressure sensors, with some limitations. The results of stability analysis show that the levee is less stable when the water level decreases, after which factor of safety decreases significantly. For all flooding wave parameters described in the paper, the levee is very stable and factor of safety variations for any particular stage were not very large.

  18. HR-EELS study of hydrogen bonding configuration, chemical and thermal stability of detonation nanodiamond films

    Energy Technology Data Exchange (ETDEWEB)

    Michaelson, Sh.; Akhvlediani, R. [Schulich Faculty of Chemistry, Technion-Israel Institute of Technology, Haifa 32000 (Israel); Petit, T.; Girard, H.A.; Arnault, J.C. [CEA, LIST, Diamond Sensors Laboratory, F-91191 Gif sur Yvette (France); Hoffman, A., E-mail: choffman@tx.technion.ac.il [Schulich Faculty of Chemistry, Technion-Israel Institute of Technology, Haifa 32000 (Israel)

    2014-06-01

    Nano-diamond films composed of 3–10 nm grains prepared by the detonation method and deposited onto silicon substrates by drop-casting were examined by high resolution electron energy loss spectroscopy (HR-EELS), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and secondary ion mass spectroscopy (SIMS). The impact of (i) ex-situ ambient annealing at 400 °C and (ii) ex-situ hydrogenation on hydrogen bonding and its thermal stability were examined. In order to clarify the changes in hydrogen bonding configuration detected on the different surfaces as a function of thermal annealing, in-situ hydrogenation by thermally activated atomic hydrogen was performed and examined. This study provides direct evidence that the exposure to ambient conditions and medium temperature ambient annealing have a pronounced effect on the hydrogen-carbon bonding configuration onto the nano-diamond surfaces. In-situ 1000 °C annealing results in irreversible changes of the film surface and partial nano-diamond silicidation.

  19. Phase change Materials (PCM) microcapsules with different shell compositions: Preparation, characterization and thermal stability

    Energy Technology Data Exchange (ETDEWEB)

    Bayes-Garcia, L.; Ventola, L.; Cordobilla, R.; Benages, R.; Calvet, T.; Cuevas-Diarte, M.A. [Departament de Cristal.lografia, Mineralogia i Diposits Minerals, Facultat de Geologia, Universitat de Barcelona, Marti i Franques s/n, E-08028 Barcelona (Spain)

    2010-07-15

    In this study, phase change materials (Rubitherm registered RT 27) microcapsules were successfully obtained by two different methods. The main difference between them remains on the shell composition, as they are composed of different coacervates (Sterilized Gelatine/Arabic Gum for the SG/AG method and Agar-Agar/Arabic Gum for the AA/AG method). Microcapsules were thermally characterized by thermo-optical microscopy and differential scanning calorimetry. Using scanning electron microscopy, their spherical morphology (sphericity factor of 0.94-0.95) and their particle size distribution were determined, obtaining an average diameter of 12 {mu}m for the SG/AG method and lower values for the AA/AG method, where nanocapsules were also observed (average diameter of 4.3 {mu}m for the microcapsules and 104 nm for the nanocapsules). The thermal stability determination was carried out by Thermogravimetric analyses (TG) and the results show a high decomposition temperature, although the process takes places in four steps for the two mentioned methods. Moreover, the microcapsules obtained by the AA/AG method decompose in a more gradual way, as in the TG results a double step, instead of one, is appreciable. On the whole, the prepared microencapsulated PCM are totally capable of developing their role in thermal energy storage. (author)

  20. Impact of Power Ultrasound on Antihypertensive Activity, Functional Properties, and Thermal Stability of Rapeseed Protein Hydrolysates

    Directory of Open Access Journals (Sweden)

    Asif Wali

    2017-01-01

    Full Text Available The effects of power ultrasound pretreatments on the degree of hydrolysis (DH, angiotensin-I-converting enzyme (ACE inhibitory activity, amino acid composition, surface hydrophobicity, protein solubility, and thermal stability of ACE inhibition of rapeseed protein hydrolysates were evaluated. Ultrasonic pretreatments before enzymolysis in terms of power and exposure time increased the DH and ACE inhibitory activities over the control (without sonication. In this study, maximum DH 22.07% and ACE inhibitory activity 72.13% were achieved at 600 W and 12 min pretreatment. Compared to the hydrolysates obtained without sonication, the amino acid profile of ultrasound pretreated hydrolysates showed significant changes particularly in the proline content and hydrophobic amino acids with an increased rate of 2.47% and 6.31%, respectively. Ultrasound pretreatment (600 watts, 12 min improved functional properties of protein hydrolysates over control by enhancing surface hydrophobicity and solubility index with an increased rate of 130.76% and 34.22%. Moreover, the stability test showed that the ACE inhibitory activity remains stable against heat treatments. However, extensive heat, prolonged heating time, and alkaline conditions were not in the favor of stability test, while under mild heat and acidic conditions their ACE inhibitory activities were not significantly different from unheated samples.

  1. Influences of the Structure of Lipids on Thermal Stability of Lipid Membranes

    International Nuclear Information System (INIS)

    Hai Nan-Nan; Zhou Xin; Li Ming

    2015-01-01

    The binding free energy (BFE) of lipid to lipid bilayer is a critical factor to determine the thermal or mechanical stability of the bilayer. Although the molecular structure of lipids has significant impacts on BFE of the lipid, there lacks a systematic study on this issue. In this paper we use coarse-grained molecular dynamics simulation to investigate this problem for several typical phospholipids. We find that both the tail length and tail unsaturation can significantly affect the BFE of lipids but in opposite way, namely, BFE decreases linearly with increasing length, but increases linearly with addition of unsaturated bonds. Inspired by the specific structure of cholesterol which is a crucial component of biomembrane, we also find that introduction of carbo-ring-like structures to the lipid tail or to the bilayer may greatly enhance the stability of the bilayer. Our simulation also shows that temperature can influence the bilayer stability and this effect can be significant when the bilayer undergoes phase transition. These results may be helpful to the design of liposome or other self-assembled lipid systems. (paper)

  2. Thermal stability analysis of YBCO-coated conductors subject to over-currents

    Energy Technology Data Exchange (ETDEWEB)

    MartInez, E; Angurel, L A; Pelegrin, J [Instituto de Ciencia de Materiales de Aragon, CSIC-Universidad de Zaragoza, C/Maria de Luna 3, E-50018 Zaragoza (Spain); Xie, Y Y; Selvamanickam, V [SuperPower Incorporated, Schenectady, NY 12304 (United States)

    2010-02-15

    The thermal stability of superconducting YBCO-coated conductors subject to over-currents are analysed. We have studied the effect of DC and AC over-current pulses in Cu-stabilized and non-stabilized coated conductors by measuring the electric field and temperature profiles of these conductors immersed in liquid nitrogen. Current pulses of short duration of about 90 ms and long duration of a few seconds were applied to the samples. Three different cooling regimes of liquid nitrogen-convection, nucleate boiling and film boiling-were observed and their influence on the recovery time of superconductivity in the coated conductors after the over-current pulses has been analysed. We have studied the recovery behaviour under two different conditions, in which the current was set to zero and to the operating current after the current pulses. These experiments simulated the conditions during an over-current situation in different electric power applications with special attention given to the behaviour of these coated conductors acting as in-fault current limiters.

  3. Thermal stability analysis of YBCO-coated conductors subject to over-currents

    International Nuclear Information System (INIS)

    MartInez, E; Angurel, L A; Pelegrin, J; Xie, Y Y; Selvamanickam, V

    2010-01-01

    The thermal stability of superconducting YBCO-coated conductors subject to over-currents are analysed. We have studied the effect of DC and AC over-current pulses in Cu-stabilized and non-stabilized coated conductors by measuring the electric field and temperature profiles of these conductors immersed in liquid nitrogen. Current pulses of short duration of about 90 ms and long duration of a few seconds were applied to the samples. Three different cooling regimes of liquid nitrogen-convection, nucleate boiling and film boiling-were observed and their influence on the recovery time of superconductivity in the coated conductors after the over-current pulses has been analysed. We have studied the recovery behaviour under two different conditions, in which the current was set to zero and to the operating current after the current pulses. These experiments simulated the conditions during an over-current situation in different electric power applications with special attention given to the behaviour of these coated conductors acting as in-fault current limiters.

  4. Thermal Stability of RNA Phage Virus-Like Particles Displaying Foreign Peptides

    Directory of Open Access Journals (Sweden)

    Peabody David S

    2011-05-01

    Full Text Available Abstract Background To be useful for genetic display of foreign peptides a viral coat protein must tolerate peptide insertions without major disruption of subunit folding and capsid assembly. The folding of the coat protein of RNA phage MS2 does not normally tolerate insertions in its AB-loop, but an engineered single-chain dimer readily accepts them as long as they are restricted to one of its two halves. Results Here we characterize the effects of peptide insertions on the thermal stabilities of MS2 virus-like particles (VLPs displaying a variety of different peptides in one AB-loop of the coat protein single-chain dimer. These particles typically denature at temperatures around 5-10°C lower than unmodified VLPs. Even so, they are generally stable up to about 50°C. VLPs of the related RNA phage PP7 are cross-linked with intersubunit disulfide bonds and are therefore significantly more stable. An AB-loop insertion also reduces the stability of PP7 VLPs, but they only begin to denature above about 70°C. Conclusions VLPs assembled from MS2 single-chain dimer coat proteins with peptide insertions in one of their AB-loops are somewhat less stable than the wild-type particle, but still resist heating up to about 50°C. Because they possess disulfide cross-links, PP7-derived VLPs provide an alternate platform with even higher stability.

  5. Improving thermal stability of a resonator fiber optic gyro employing a polarizing resonator.

    Science.gov (United States)

    Yu, Xuhui; Ma, Huilian; Jin, Zhonghe

    2013-01-14

    To improve the thermal stability of a resonator fiber optic gyro (R-FOG), a transmission-type polarizing resonator by inserting two in-line polarizers in a polarization-maintaining fiber resonator with twin 90° polarization-axis rotated splices is proposed and experimentally demonstrated. The in-line polarizers attenuate the unwanted resonance by introducing high loss for the unwanted eigenstates of polarization in the resonator. The desired resonance in the resonator can keep excellent stability in a wide temperature range, thus the temperature-related polarization error in the R-FOG is dramatically suppressed. Both our numerical simulation and experimental verification are carried out, which for the first time to our best knowledge demonstrate that the open-loop output of the R-FOG is insensitive to environmental temperature variations. A bias stability below 2°/h in the temperature range of 36.2°C to 33°C is successfully demonstrated.

  6. Thermal stability control system of photo-elastic interferometer in the PEM-FTs

    Science.gov (United States)

    Zhang, M. J.; Jing, N.; Li, K. W.; Wang, Z. B.

    2018-01-01

    A drifting model for the resonant frequency and retardation amplitude of a photo-elastic modulator (PEM) in the photo-elastic modulated Fourier transform spectrometer (PEM-FTs) is presented. A multi-parameter broadband-matching driving control method is proposed to improve the thermal stability of the PEM interferometer. The automatically frequency-modulated technology of the driving signal based on digital phase-locked technology is used to track the PEM's changing resonant frequency. Simultaneously the maximum optical-path-difference of a laser's interferogram is measured to adjust the amplitude of the PEM's driving signal so that the spectral resolution is stable. In the experiment, the multi-parameter broadband-matching control method is applied to the driving control system of the PEM-FTs. Control of resonant frequency and retardation amplitude stabilizes the maximum optical-path-difference to approximately 236 μm and results in a spectral resolution of 42 cm-1. This corresponds to a relative error smaller than 2.16% (4.28 standard deviation). The experiment shows that the method can effectively stabilize the spectral resolution of the PEM-FTs.

  7. Enhanced thermal stability of a polymer solar cell blend induced by electron beam irradiation in the transmission electron microscope

    Energy Technology Data Exchange (ETDEWEB)

    Bäcke, Olof, E-mail: obacke@chalmers.se [Department of Applied Physics, Chalmers University of Technology, 41296 Göteborg (Sweden); Lindqvist, Camilla; Diaz de Zerio Mendaza, Amaia [Department of Chemistry and Chemical Engineering, Chalmers University of Technology, 41296 Göteborg (Sweden); Gustafsson, Stefan [Department of Applied Physics, Chalmers University of Technology, 41296 Göteborg (Sweden); Wang, Ergang; Andersson, Mats R.; Müller, Christian [Department of Chemistry and Chemical Engineering, Chalmers University of Technology, 41296 Göteborg (Sweden); Kristiansen, Per Magnus [Institute of Polymer Nanotechnology (INKA), FHNW University of Applied Science and Arts Northwestern Switzerland, 5210 Windisch (Switzerland); Laboratory for Micro- and Nanotechnology, Paul Scherrer Institute, 5232 Villigen (Switzerland); Olsson, Eva, E-mail: eva.olsson@chalmers.se [Department of Applied Physics, Chalmers University of Technology, 41296 Göteborg (Sweden)

    2017-05-15

    We show by in situ microscopy that the effects of electron beam irradiation during transmission electron microscopy can be used to lock microstructural features and enhance the structural thermal stability of a nanostructured polymer:fullerene blend. Polymer:fullerene bulk-heterojunction thin films show great promise for use as active layers in organic solar cells but their low thermal stability is a hindrance. Lack of thermal stability complicates manufacturing and influences the lifetime of devices. To investigate how electron irradiation affects the thermal stability of polymer:fullerene films, a model bulk-heterojunction film based on a thiophene-quinoxaline copolymer and a fullerene derivative was heat-treated in-situ in a transmission electron microscope. In areas of the film that exposed to the electron beam the nanostructure of the film remained stable, while the nanostructure in areas not exposed to the electron beam underwent large phase separation and nucleation of fullerene crystals. UV–vis spectroscopy shows that the polymer:fullerene films are stable for electron doses up to 2000 kGy. - Highlights: • Thermal stability of a polymer: fullerne blend is increased using electron irradiation. • Using in-situ transmission electron microscopy the nanostructure is studied. • Electron irradiation stops phase separation between the polymer and fullerene. • Electron irradiation quenches the formation and nucleation of fullerene crystals.

  8. Comparison of stabilization by Vitamin E and 2,6-di-tert-butylphenols during polyethylene radio-thermal-oxidation

    Science.gov (United States)

    Richaud, Emmanuel

    2014-10-01

    This paper reports a compilation of data for PE+Vitamin E and 2,6-di-tert-butylphenols oxidation in radio-thermal ageing. Data unambiguously show that Vitamin E reacts with Prad and POOrad whereas 2,6-di-tert-butyl phenols only react with POOrad. Kinetic parameters of the stabilization reactions for both kinds of antioxidants were tentatively extracted from phenol depletion curves, and discussed regarding the structure of the stabilizer. They were also used for completing an existing kinetic model used for predicting the stabilization by antioxidants. This one permits to compare the efficiency of stabilizer with dose rate or sample thickness.

  9. Impact of a thermal treatment at different pH on the adsorption behaviour of untreated and enzyme-modified egg yolk at the oil-water interface.

    Science.gov (United States)

    Daimer, Katharina; Kulozik, Ulrich

    2010-01-01

    Adsorption properties of egg yolk proteins were investigated with or without enzymatic modification with phospholipase A(2) (PLA(2)) and after a thermal treatment at pH 4 and 6.5. Heat treatment was assessed from 60 to 90 degrees C resulting in a wide range of protein denaturation degrees, which were correlated with the interfacial protein load of emulsion droplets. It was shown that denatured proteins, i.e. protein aggregates are able to adsorb at the oil-water interface and that, most notably, granule constituents play an important role in stabilisation of the oil-water interface at pH 4. Moreover, it was shown that after a thermal treatment of untreated egg yolk (not enzyme treated) an even higher protein load is reached than when PLA(2)-treated egg yolk is used for emulsification. Heat-treated natural egg yolk is therefore supposed to be an appropriate alternative for PLA(2)-treated egg yolk for producing stable emulsions. The SDS-Page profiles show that the composition of the interfacial film is highly influenced by a modification with PLA(2) at pH 4 while at pH 6.5 the interfacial composition of adsorbed proteins is less influenced.

  10. The Influence of pH and Temperature on the Stability of N-[(Piperidinemethylene]daunorubicin Hydrochloride and a Comparison of the Stability of Daunorubicin and Its Four New Amidine Derivatives in Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Mikołaj Piekarski

    2014-01-01

    Full Text Available The influence of pH and temperature on the stability of N-[(piperidinemethylene]daunorubicin hydrochloride (PPD was investigated. Degradation was studied using an HPLC method. Specific acid-base catalysis of PPD involves hydrolysis of protonated molecules of PPD catalyzed by hydrogen ions and spontaneous hydrolysis under the influence of water zwitterions, unprotonated molecules, and monoanions of PPD. The thermodynamic parameters of these reactions, energy, enthalpy, and entropy, were calculated. Also, the stability of daunorubicin and its new amidine derivatives (piperidine, morpholine, pyrrolidine, and hexahydroazepin-1-yl in aqueous solutions was compared and discussed.

  11. Thermal stability and structural changes in bacterial toxins responsible for food poisoning.

    Science.gov (United States)

    Regenthal, Paulina; Hansen, Jesper S; André, Ingemar; Lindkvist-Petersson, Karin

    2017-01-01

    The staphylococcal enterotoxins (SEs) are secreted by the bacteria Staphylococcus aureus and are the most common causative agent in staphylococcal food poisoning. The staphylococcal enterotoxin A (SEA) has been associated with large staphylococcal food poisoning outbreaks, but newer identified SEs, like staphylococcal enterotoxin H (SEH) has recently been shown to be present at similar levels as SEA in food poisoning outbreaks. Thus, we set out to investigate the thermo-stability of the three-dimensional structures of SEA, SEH and staphylococcal enterotoxin E (SEE), since heat inactivation is a common method to inactivate toxins during food processing. Interestingly, the investigated toxins behaved distinctly different upon heating. SEA and SEE were more stable at slightly acidic pH values, while SEH adopted an extremely stable structure at neutral pH, with almost no effects on secondary structural elements upon heating to 95°C, and with reversible formation of tertiary structure upon subsequent cooling to room temperature. Taken together, the data suggests that the family of staphylococcal enterotoxins have different ability to withstand heat, and thus the exact profile of heat inactivation for all SEs causing food poisoning needs to be considered to improve food safety.

  12. Oxidative stability of 70% fish oil‐in‐water emulsions: Impact of emulsifiers and pH

    DEFF Research Database (Denmark)

    Horn, Anna Frisenfeldt; Nielsen, Nina Skall; Andersen, Ulf

    2011-01-01

    The objective of this study was to evaluate the protective effects of five different emulsifiers on lipid oxidation in 70% fish oil‐in‐water emulsions to be used as delivery systems for long chain polyunsaturated omega‐3 fatty acids to foods. The emulsifiers were either phospholipid (PL) based...... or protein based. The PL‐based emulsifiers were soy lecithin and two milk PL concentrates (with either 20 or 75% PL). The protein‐based emulsifiers were whey protein isolate and sodium caseinate. Lipid oxidation was studied at two pH values (pH 4.5 and 7.0) and results were compared to lipid oxidation...

  13. Catalysis and stability of an alkaline protease from a haloalkaliphilic bacterium under non-aqueous conditions as a function of pH, salt and temperature.

    Science.gov (United States)

    Pandey, Sandeep; Rakholiya, Kalpna D; Raval, Vikram H; Singh, Satya P

    2012-09-01

    A haloalkaliphilic bacterium, isolated from Coastal Gujarat (India) was identified as Oceanobacillus sp. (GQ162111) based on 16S rRNA gene sequence. The organism grew and secreted extra cellular protease in presence of various organic solvents. At 30% (v/v) concentration of hexane, heptane, isooctane, dodecane and decane, significant growth and protease production was evident. The alkaline protease was purified in a single step on phenyl sepharose 6 FF with 28% yield. The molecular mass as judged by SDS-PAGE was 30 kDa. The temperature optimum of protease was 50°C and the enzyme retained 70% activity in 10% (v/v) isooctane. Effect of salt and pH was investigated in combination to assess the effect of isooctane. In organic solvents, the enzyme was considerably active at pH 8-11, with optimum activity at pH 10. Salt at 2 M was optimum for activity and enzyme maintained significant stability up to 18 h even at 3 M salt concentration. Patters of growth, protease production, catalysis and stability of the enzyme are presented. The study resumes significance as limited information is available on the interaction of haloalkaliphilic bacteria and their enzymes with organic solvents. Copyright © 2012 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

  14. Crystallization behaviour and thermal stability of two aluminium-based metallic glass powder materials

    Energy Technology Data Exchange (ETDEWEB)

    Li, X.P.; Yan, M. [University of Queensland, School of Mechanical and Mining Engineering, ARC Centre of Excellence for Design in Light Metals, Brisbane, QLD 4072 (Australia); Yang, B.J. [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Wang, J.Q., E-mail: jqwang@imr.ac.cn [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Schaffer, G.B. [University of Queensland, School of Mechanical and Mining Engineering, ARC Centre of Excellence for Design in Light Metals, Brisbane, QLD 4072 (Australia); Qian, M., E-mail: ma.qian@uq.edu.au [University of Queensland, School of Mechanical and Mining Engineering, ARC Centre of Excellence for Design in Light Metals, Brisbane, QLD 4072 (Australia)

    2011-12-15

    Highlights: Black-Right-Pointing-Pointer The crystallization paths and products of Al{sub 86}Ni{sub 7}Y{sub 4.5}Co{sub 1}La{sub 1.5} powder have been identified. Black-Right-Pointing-Pointer The thermal stability of Al{sub 86}Ni{sub 7}Y{sub 4.5}Co{sub 1}La{sub 1.5} powder has been assessed. Black-Right-Pointing-Pointer The Al{sub 86}Ni{sub 7}Y{sub 4.5}Co{sub 1}La{sub 1.5} powder shows a wide processing window of 75 K. Black-Right-Pointing-Pointer The powder has the potential to be consolidated into thick BMG components based on the findings. Black-Right-Pointing-Pointer The Al{sub 85}Ni{sub 5}Y{sub 6}Co{sub 2}Fe{sub 2} powder shows similar characteristics but inferior thermal stability. - Abstract: The crystallization behaviour and thermal stability of two Al-based metallic glass powder materials, Al{sub 85}Ni{sub 5}Y{sub 6}Co{sub 2}Fe{sub 2} and Al{sub 86}Ni{sub 6}Y{sub 4.5}Co{sub 2}La{sub 1.5}, have been investigated using differential scanning calorimetry (DSC), X-ray diffraction (XRD) and electron microscopy. Both alloy powders show a distinct three-stage crystallization process with a similar gap of {approx}75 K between the onset crystallization temperature (T{sub x}) and the second crystallization temperature. Crystallization occurs by the precipitation and growth of fcc-Al, without intermetallic formation. The apparent activation energy for each stage of crystallization was determined from DSC analyses and the phases resulting from each crystallization stage were identified by XRD and electron microscopy. The critical cooling rate for each alloy powder was calculated from the DSC data. These results are necessary to inform the consolidation of amorphous powder particles of Al{sub 85}Ni{sub 5}Y{sub 6}Co{sub 2}Fe{sub 2} or Al{sub 86}Ni{sub 6}Y{sub 4.5}Co{sub 2}La{sub 1.5} into thick (>1 mm) metallic glass components.

  15. Thermal and physico-mechanical stability of recycled high density polyethylene reinforced with oil palm fibres

    Directory of Open Access Journals (Sweden)

    R.O. Medupin

    2017-12-01

    Full Text Available The impressive physical and mechanical properties achievable with organic fillers make them a good choice for polymer composite reinforcement. In this study, oil palm fibres (OPF, often hardly thought of as having any reasonable economic value in developing economy was used as reinforcing fillers in recycled high density polyethylene (rHDPE. Thermal behaviour, physical and mechanical stability of rHDPE filled with OPF have been studied. Fourier Transform Infrared Spectroscopy (FTIR results present band spectra characteristic of OH stretching vibration in the cellulose of the fibre material. The absorption bands of the spectra are attributed to the presence of stretching vibration of CO group mostly found in the form of hemicelluloses and lignin structure in the fibre. Upon examination of the test specimens produced through compression moulding technique, it was found that the addition of OPF (filler into rHDPE (matrix increased the composites’ water absorption rate linearly for the first 16 days of exposure to the water environment. Stability was achieved for all the materials after this period. Thermal studies of the various compositions (OPF/rHDPE: 5/95, 10/90, 15/85, 20/80 and 25/75 using derivative thermogravimetric analysis (DTGA showed two main degradation peaks at 490 °C and 380 °C. The mechanical study revealed that the composite with 20 wt% filler contents was the most eco-friendly and had the best mechanical properties while that with 25 wt% was the most thermally stable. This material was thermally stable up to approximately 330 °C. Microstructure examination of the different components of the composites further explains the reason for good physical and mechanical strength of the sample with 20 wt% filler. It can, therefore, be inferred from the results of the various analyses conducted that OPF is a good reinforcing phase for rHDPE and a potential material for construction and automotive industries.

  16. Simultaneously Tailoring Surface Energies and Thermal Stabilities of Cellulose Nanocrystals Using Ion Exchange: Effects on Polymer Composite Properties for Transportation, Infrastructure, and Renewable Energy Applications.

    Science.gov (United States)

    Fox, Douglas M; Rodriguez, Rebeca S; Devilbiss, Mackenzie N; Woodcock, Jeremiah; Davis, Chelsea S; Sinko, Robert; Keten, Sinan; Gilman, Jeffrey W

    2016-10-12

    Cellulose nanocrystals (CNCs) have great potential as sustainable reinforcing materials for polymers, but there are a number of obstacles to commercialization that must first be overcome. High levels of water absorption, low thermal stabilities, poor miscibility with nonpolar polymers, and irreversible aggregation of the dried CNCs are among the greatest challenges to producing cellulose nanocrystal-polymer nanocomposites. A simple, scalable technique to modify sulfated cellulose nanocrystals (Na-CNCs) has been developed to address all of these issues. By using an ion exchange process to replace Na + with imidazolium or phosphonium cations, the surface energy is altered, the thermal stability is increased, and the miscibility of dried CNCs with a nonpolar polymer (epoxy and polystyrene) is enhanced. Characterization of the resulting ion exchanged CNCs (IE-CNCs) using potentiometry, inverse gas chromatography, dynamic vapor sorption, and laser scanning confocal microscopy reveals that the IE-CNCs have lower surface energies, adsorb less water, and have thermal stabilities of up to 100 °C higher than those of prepared protonated cellulose nanocrystals (H-CNCs) and 40 °C higher than that of neutralized Na-CNC. Methyl(triphenyl)phosphonium exchanged cellulose nanocrystals (MePh 3 P-CNC) adsorbed 30% less water than Na-CNC, retained less water during desorption, and were used to prepare well-dispersed epoxy composites without the aid of a solvent and well-dispersed polystyrene nanocomposites using a melt blending technique at 195 °C. Predictions of dispersion quality and glass transition temperatures from molecular modeling experiments match experimental observations. These fiber-reinforced polymers can be used as lightweight composites in transportation, infrastructure, and renewable energy applications.

  17. Influence of Molecular Shape on the Thermal Stability and Molecular Orientation of Vapor-Deposited Organic Semiconductors.

    Science.gov (United States)

    Walters, Diane M; Antony, Lucas; de Pablo, Juan J; Ediger, M D

    2017-07-20

    High thermal stability and anisotropic molecular orientation enhance the performance of vapor-deposited organic semiconductors, but controlling these properties is a challenge in amorphous materials. To understand the influence of molecular shape on these properties, vapor-deposited glasses of three disk-shaped molecules were prepared. For all three systems, enhanced thermal stability is observed for glasses prepared over a wide range of substrate temperatures and anisotropic molecular orientation is observed at lower substrate temperatures. For two of the disk-shaped molecules, atomistic simulations of thin films were also performed and anisotropic molecular orientation was observed at the equilibrium liquid surface. We find that the structure and thermal stability of these vapor-deposited glasses results from high surface mobility and partial equilibration toward the structure of the equilibrium liquid surface during the deposition process. For the three molecules studied, molecular shape is a dominant factor in determining the anisotropy of vapor-deposited glasses.

  18. Stability of Atenolol, Clonazepam, Dexamethasone, Diclofenac Sodium, Diltiazem, Enalapril Maleate, Ketoprofen, Lamotrigine, Penicillamine-D, and Thiamine in SyrSpend SF PH4 Oral Suspensions.

    Science.gov (United States)

    Polonini, Hudson C; Loures, Sharlene; Lima, Luis Claudio; Ferreira, Anderson O; Brandão, Marcos Antônio F

    2016-01-01

    The objective of this study was to evaluate the stability of 10 commonly used active pharmaceutical ingredients compounded in oral suspensions using SyrSpend SF PH4 (atenolol 1.0 and 5.0 mg/mL, clonazepam 0.2 mg/mL, dexamethasone 1.0 mg/mL, diclofenac sodium 5.0 mg/mL, diltiazem 12.0 mg/mL, enalapril maleate 1.0 mg/mL, ketoprofen 20.0 mg/mL, lamotrigine 1.0 mg/mL, penicillamine-D 50.0 mg/mL, thiamine 100 mg/m) and stored both at controlled refrigerated (2°C to 8°C) and room temperature (20°C to 25°C). Stability was assessed by means of measuring percent recovery at varying time points throughout a 90-day period. The quantification of the active pharmaceutical ingredients was performed by a stability-indicating, high-performance liquid chromatographic method. The beyond-use date of the products was found to be at least 90 days for all suspensions (except atenolol 1 mg/mL, which was stable up to 60 days), both for controlled refrigerated temperature and room temperature. This confirms that SyrSpend SF PH4 is a stable suspending vehicle for compounding with a broad range of different active pharmaceutical ingredients.

  19. Methylation of Brazilein on Secang (Caesalpinia sappan Linn) Wood Extract for Maintain Color Stability to the Changes of pH

    Science.gov (United States)

    Ulma, Zeni; Rahayuningsih, Edia; Dwi Wahyuningsih, Tutik

    2018-01-01

    The stability of natural dyes to the changes of pH is really necessary when the natural dyes are applied either on fabric or food. This research aimed to increase the stability of brazilein, a compound contained within the secang wood extract, to the changes of pH. The methylation process was done by reacting Dimethyl Carbonate (DMC) with the brazilein on the secang wood extract. DMC acts as a substance that substitute hydroxyl group on brazilein. The methylation reaction of brazilein on secang wood extract was operated on a three-necked round-bottomed flask fitted with mercury-sealed stirrer and reflux condenser under 80°C temperature and 250 rpm stirring speed. There were two variables observed in this research; the DMC amount ratio to the amount of secang wood extract and the time of the methylation process. The research showed that at the 1:10 the DMC amount ratio to the amount of wood extract and 8 hours of the methylation process give the better stability of color of the secang wood extract than the variation of the other variables.

  20. A neutron scattering study on the stability of trehalose mycolates under thermal stress

    Science.gov (United States)

    Migliardo, F.; Salmeron, C.; Bayan, N.

    2013-10-01

    The present paper is focused on the study of the dynamics of mycolic acids, which are fundamental components of the outer membrane (mycomembrane) of Mycobacterium tuberculosis. An elastic neutron scattering study of mycolic acid/H2O and lecithin/H2O mixtures as a function of temperature and exchanged wavevector Q has been carried out. This study provides an effective way for characterizing the dynamical properties, furnishing a set of parameters characterizing the different flexibility and rigidity of the investigated lipids. The behavior of the elastically scattered intensity profiles and the derived mean square displacements as a function of temperature shows a more marked temperature dependence for lecithin lipids in comparison with mycolic acids, so revealing a higher thermal stability of these latter. These findings could be useful for understanding the dynamics-function relation in the mycomembrane and then to relate it to the low permeability and high resistance of mycobacteria to many antibiotics.