WorldWideScience

Sample records for thermal rectification date

  1. Radiative thermal rectification using superconducting materials

    Energy Technology Data Exchange (ETDEWEB)

    Nefzaoui, Elyes, E-mail: elyes.nefzaoui@univ-poitiers.fr; Joulain, Karl, E-mail: karl.joulain@univ-poitiers.fr; Drevillon, Jérémie; Ezzahri, Younès [Institut Pprime, Université de Poitiers-CNRS-ENSMA, 2, Rue Pierre Brousse, Bâtiment B25, TSA 41105, 86073 Poitiers Cedex 9 (France)

    2014-03-10

    Thermal rectification can be defined as an asymmetry in the heat flux when the temperature difference between two interacting thermal reservoirs is reversed. In this Letter, we present a far-field radiative thermal rectifier based on high-temperature superconducting materials with a rectification ratio up to 80%. This value is among the highest reported in literature. Two configurations are examined: a superconductor (Tl{sub 2}Ba{sub 2}CaCu{sub 2}O{sub 8}) exchanging heat with (1) a black body and (2) another superconductor, YBa{sub 2}Cu{sub 3}O{sub 7} in this case. The first configuration shows a higher maximal rectification ratio. Besides, we show that the two-superconductor rectifier exhibits different rectification regimes depending on the choice of the reference temperature, i.e., the temperature of the thermostat. Presented results might be useful for energy conversion devices, efficient cryogenic radiative insulators engineering, and thermal logical circuits’ development.

  2. Thermal rectification in nonlinear quantum circuits

    DEFF Research Database (Denmark)

    Ruokola, T.; Ojanen, T.; Jauho, Antti-Pekka

    2009-01-01

    We present a theoretical study of radiative heat transport in nonlinear solid-state quantum circuits. We give a detailed account of heat rectification effects, i.e., the asymmetry of heat current with respect to a reversal of the thermal gradient, in a system consisting of two reservoirs at finit...

  3. Thermal conductivity and thermal rectification in unzipped carbon nanotubes

    International Nuclear Information System (INIS)

    Ni Xiaoxi; Li Baowen; Zhang Gang

    2011-01-01

    We study the thermal transport in completely unzipped carbon nanotubes, which are called graphene nanoribbons, partially unzipped carbon nanotubes, which can be seen as carbon-nanotube-graphene-nanoribbon junctions, and carbon nanotubes by using molecular dynamics simulations. It is found that the thermal conductivity of a graphene nanoribbon is much less than that of its perfect carbon nanotube counterparts because of the localized phonon modes at the boundary. A partially unzipped carbon nanotube has the lowest thermal conductivity due to additional localized modes at the junction region. More strikingly, a significant thermal rectification effect is observed in both partially unzipped armchair and zigzag carbon nanotubes. Our results suggest that carbon-nanotube-graphene-nanoribbon junctions can be used in thermal energy control.

  4. Thermal rectification based on phonon hydrodynamics and thermomass theory

    Directory of Open Access Journals (Sweden)

    Dong Yuan

    2016-06-01

    Full Text Available The thermal diode is the fundamental device for phononics. There are various mechanisms for thermal rectification, e.g. different temperature dependent thermal conductivity of two ends, asymmetric interfacial resistance, and nonlocal behavior of phonon transport in asymmetric structures. The phonon hydrodynamics and thermomass theory treat the heat conduction in a fluidic viewpoint. The phonon gas flowing through the media is characterized by the balance equation of momentum, like the Navier-Stokes equation for fluid mechanics. Generalized heat conduction law thereby contains the spatial acceleration (convection term and the viscous (Laplacian term. The viscous term predicts the size dependent thermal conductivity. Rectification appears due to the MFP supersession of phonons. The convection term also predicts rectification because of the inertia effect, like a gas passing through a nozzle or diffuser.

  5. Thermal conductivity and rectification in asymmetric archaeal lipid membranes

    Science.gov (United States)

    Youssefian, Sina; Rahbar, Nima; Van Dessel, Steven

    2018-05-01

    Nature employs lipids to construct nanostructured membranes that self-assemble in an aqueous environment to separate the cell interior from the exterior environment. Membrane composition changes among species and according to environmental conditions, which allows organisms to occupy a wide variety of different habitats. Lipid bilayers are phase-change materials that exhibit strong thermotropic and lyotropic phase behavior in an aqueous environment, which may also cause thermal rectification. Among different types of lipids, archaeal lipids are of great interest due to their ability to withstand extreme conditions. In this paper, nonequilibrium molecular dynamics simulations were employed to study the nanostructures and thermal properties of different archaeols and to investigate thermal rectification effects in asymmetric archaeal membranes. In particular, we are interested in understanding the role of bridged phytanyl chains and cyclopentane groups in controlling the phase transition temperature and heat flow across the membrane. Our results indicate that the bridged phytanyl chains decrease the molecular packing of lipids, whereas the existence of cyclopentane rings on the tail groups increases the molecular packing by enhancing the interactions between isoprenoid chains. We found that macrocyclic archaeols have the highest thermal conductivity, whereas macrocyclic archaeols with two cyclopentane rings have the lowest. The effect of the temperature on the variation of thermal conductivity was found to be progressive. Our results further indicate that small thermal rectification effects occur in asymmetric archaeol bilayer membranes at around 25 K temperature gradient. The calculated thermal rectification factor was around 0.09 which is in the range of rectification factor obtained experimentally for nanostructures such as carbon nanotubes (0.07). Such phenomena may be of biological significance and could also be optimized for use in various engineering

  6. Thermal rectification and negative differential thermal conductance in harmonic chains with nonlinear system-bath coupling

    Science.gov (United States)

    Ming, Yi; Li, Hui-Min; Ding, Ze-Jun

    2016-03-01

    Thermal rectification and negative differential thermal conductance were realized in harmonic chains in this work. We used the generalized Caldeira-Leggett model to study the heat flow. In contrast to most previous studies considering only the linear system-bath coupling, we considered the nonlinear system-bath coupling based on recent experiment [Eichler et al., Nat. Nanotech. 6, 339 (2011), 10.1038/nnano.2011.71]. When the linear coupling constant is weak, the multiphonon processes induced by the nonlinear coupling allow more phonons transport across the system-bath interface and hence the heat current is enhanced. Consequently, thermal rectification and negative differential thermal conductance are achieved when the nonlinear couplings are asymmetric. However, when the linear coupling constant is strong, the umklapp processes dominate the multiphonon processes. Nonlinear coupling suppresses the heat current. Thermal rectification is also achieved. But the direction of rectification is reversed compared to the results of weak linear coupling constant.

  7. Rectification of thermal fluctuations in ideal gases.

    Science.gov (United States)

    Meurs, P; Van den Broeck, C; Garcia, A

    2004-11-01

    We calculate the systematic average speed of the adiabatic piston and a thermal Brownian motor, introduced by C. Van den Broeck, R, Kawai and P. Meurs [Phys. Rev. Lett. 93, 090601 (2004)], by an expansion of the Boltzmann equation and compare with the exact numerical solution.

  8. Quantum thermal rectification to design thermal diodes and transistors

    Energy Technology Data Exchange (ETDEWEB)

    Joulain, Karl; Ezzahri, Younes; Ordonez-Miranda, Jose [Univ. de Poitiers, Futuroscope Chasseneuil (France). Inst. Pprime, CNRS

    2017-05-01

    We study in this article how heat can be exchanged between two-level systems, each of them being coupled to a thermal reservoir. Calculations are performed solving a master equation for the density matrix using the Born-Markov approximation. We analyse the conditions for which a thermal diode and a thermal transistor can be obtained as well as their optimisation.

  9. Thermal conductivity and thermal rectification in graphene nanoribbons: a molecular dynamics study.

    Science.gov (United States)

    Hu, Jiuning; Ruan, Xiulin; Chen, Yong P

    2009-07-01

    We have used molecular dynamics to calculate the thermal conductivity of symmetric and asymmetric graphene nanoribbons (GNRs) of several nanometers in size (up to approximately 4 nm wide and approximately 10 nm long). For symmetric nanoribbons, the calculated thermal conductivity (e.g., approximately 2000 W/m-K at 400 K for a 1.5 nm x 5.7 nm zigzag GNR) is on the similar order of magnitude of the experimentally measured value for graphene. We have investigated the effects of edge chirality and found that nanoribbons with zigzag edges have appreciably larger thermal conductivity than nanoribbons with armchair edges. For asymmetric nanoribbons, we have found significant thermal rectification. Among various triangularly shaped GNRs we investigated, the GNR with armchair bottom edge and a vertex angle of 30 degrees gives the maximal thermal rectification. We also studied the effect of defects and found that vacancies and edge roughness in the nanoribbons can significantly decrease the thermal conductivity. However, substantial thermal rectification is observed even in the presence of edge roughness.

  10. Very large thermal rectification in bulk composites consisting partly of icosahedral quasicrystals

    International Nuclear Information System (INIS)

    Takeuchi, Tsunehiro

    2014-01-01

    The bulk thermal rectifiers usable at a high temperature above 300 K were developed by making full use of the unusual electron thermal conductivity of icosahedral quasicrystals. The unusual electron thermal conductivity was caused by a synergy effect of quasiperiodicity and by a narrow pseudogap at the Fermi level. The rectification ratio, defined by TRR = |J large |/|J small |, reached vary large values exceeding 2.0. This significant thermal rectification would lead to new practical applications for the heat management. (paper)

  11. Molecular dynamics study on the thermal conductivity and thermal rectification in graphene with geometric variations of doped boron

    Energy Technology Data Exchange (ETDEWEB)

    Liang, Qi, E-mail: alfred_02030210@163.com; Wei, Yuan

    2014-03-15

    Thermal conductivity and thermal rectification of graphene with geometric variations have been investigated by using classical non-equilibrium molecular dynamics simulation, and analyzed theoretically the cause of the changes of thermal conductivity and thermal rectification. Two different structural models, triangular single-boron-doped graphene (SBDG) and parallel various-boron-doped graphene (VBDG), were considered. The results indicated that the thermal conductivities of two different models are about 54–63% lower than pristine graphene. And it was also found that the structure of parallel various-boron-doped graphene is inhibited more strongly on the heat transfer than that of triangular single-boron-doped graphene. The reduction in the thermal conductivities of two different models gradually decreases as the temperature rises. The thermal conductivities of triangular boron-doped graphene have a large difference in both directions, and the thermal rectification of this structure shows the downward trend with increasing temperature. However, the thermal conductivities of parallel various-boron-doped graphene are similar in both directions, and the thermal rectification effect is not obvious in this structure. The phenomenon of thermal rectification exits in SBDG. It implies that the SBDG might be a potential promising structure for thermal rectifier by controlling the boron-doped model.

  12. Molecular dynamics study on the thermal conductivity and thermal rectification in graphene with geometric variations of doped boron

    International Nuclear Information System (INIS)

    Liang, Qi; Wei, Yuan

    2014-01-01

    Thermal conductivity and thermal rectification of graphene with geometric variations have been investigated by using classical non-equilibrium molecular dynamics simulation, and analyzed theoretically the cause of the changes of thermal conductivity and thermal rectification. Two different structural models, triangular single-boron-doped graphene (SBDG) and parallel various-boron-doped graphene (VBDG), were considered. The results indicated that the thermal conductivities of two different models are about 54–63% lower than pristine graphene. And it was also found that the structure of parallel various-boron-doped graphene is inhibited more strongly on the heat transfer than that of triangular single-boron-doped graphene. The reduction in the thermal conductivities of two different models gradually decreases as the temperature rises. The thermal conductivities of triangular boron-doped graphene have a large difference in both directions, and the thermal rectification of this structure shows the downward trend with increasing temperature. However, the thermal conductivities of parallel various-boron-doped graphene are similar in both directions, and the thermal rectification effect is not obvious in this structure. The phenomenon of thermal rectification exits in SBDG. It implies that the SBDG might be a potential promising structure for thermal rectifier by controlling the boron-doped model

  13. Effect of triangular vacancy defect on thermal conductivity and thermal rectification in graphene nanoribbons

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Ping, E-mail: yangpingdm@ujs.edu.cn [Laboratory of Advanced Manufacturing and Reliability for MEMS/NEMS/OEDS, Jiangsu University, Zhenjiang 212013 (China); Li, Xialong; Zhao, Yanfan [Laboratory of Advanced Manufacturing and Reliability for MEMS/NEMS/OEDS, Jiangsu University, Zhenjiang 212013 (China); Yang, Haiying [School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013 (China); Wang, Shuting, E-mail: wangst@mail.hust.edu.cn [School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan, Hubei 430074 (China)

    2013-11-01

    We investigate the thermal transport properties of armchair graphene nanoribbons (AGNRs) possessing various sizes of triangular vacancy defect within a temperature range of 200–600 K by using classical molecular dynamics simulation. The results show that the thermal conductivities of the graphene nanoribbons decrease with increasing sizes of triangular vacancy defects in both directions across the whole temperature range tested, and the presence of the defect can decrease the thermal conductivity by more than 40% as the number of removed cluster atoms is increased to 25 (1.56% for vacancy concentration) owing to the effect of phonon–defect scattering. In the meantime, we find the thermal conductivity of defective graphene nanoribbons is insensitive to the temperature change at higher vacancy concentrations. Furthermore, the dependence of temperatures and various sizes of triangular vacancy defect for the thermal rectification ration are also detected. This work implies a possible route to achieve thermal rectifier for 2D materials by defect engineering.

  14. Significantly High Thermal Rectification in an Asymmetric Polymer Molecule Driven by Diffusive versus Ballistic Transport.

    Science.gov (United States)

    Ma, Hao; Tian, Zhiting

    2018-01-10

    Tapered bottlebrush polymers have novel nanoscale polymer architecture. Using nonequilibrium molecular dynamics simulations, we showed that these polymers have the unique ability to generate thermal rectification in a single polymer molecule and offer an exceptional platform for unveiling different heat conduction regimes. In sharp contrast to all other reported asymmetric nanostructures, we observed that the heat current from the wide end to the narrow end (the forward direction) in tapered bottlebrush polymers is smaller than that in the opposite direction (the backward direction). We found that a more disordered to less disordered structural transition within tapered bottlebrush polymers is essential for generating nonlinearity in heat conduction for thermal rectification. Moreover, the thermal rectification ratio increased with device length, reaching as high as ∼70% with a device length of 28.5 nm. This large thermal rectification with strong length dependence uncovered an unprecedented phenomenon-diffusive thermal transport in the forward direction and ballistic thermal transport in the backward direction. This is the first observation of radically different transport mechanisms when heat flow direction changes in the same system. The fundamentally new knowledge gained from this study can guide exciting research into nanoscale organic thermal diodes.

  15. Study of thermal conductivity and thermal rectification in exponential mass graded lattices

    Energy Technology Data Exchange (ETDEWEB)

    Shah, Tejal N. [Bhavan' s Sheth R.A. College of Science, Khanpur, Ahmedabad 380 001, Gujarat (India); Gajjar, P.N., E-mail: pngajjar@rediffmail.com [Department of Physics, University School of Sciences, Gujarat University, Ahmedabad 380 009, Gujarat (India)

    2012-01-09

    Concept of exponential mass variation of oscillators along the chain length of N oscillators is proposed in the present Letter. The temperature profile and thermal conductivity of one-dimensional (1D) exponential mass graded harmonic and anharmonic lattices are studied on the basis of Fermi–Pasta–Ulam (FPU) β model. Present findings conclude that the exponential mass graded chain provide higher conductivity than that of linear mass graded chain. The exponential mass graded anharmonic chain generates the thermal rectification of 70–75% which is better than linear mass graded materials, so far. Thus instead of using linear mass graded material, the use of exponential mass graded material will be a better and genuine choice for controlling the heat flow at nano-scale. -- Highlights: ► In PRE 82 (2010) 040101, use of mass graded material as a thermal devices is explored. ► Concept of exponential mass graded material is proposed. ► The rectification obtained is about 70–75% which is better than linear mass graded materials. ► The exponential mass graded material will be a better choice for the thermal devices at nano-scale.

  16. Vibrational spectra and thermal rectification in three-dimensional anharmonic lattices

    International Nuclear Information System (INIS)

    Lan Jinghua; Li Baowen

    2007-01-01

    We study thermal rectification in a three-dimensional model consisting of two segments of anharmonic lattices. One segment consists of layers of harmonic oscillator arrays coupled to a substrate potential, which is a three-dimensional Frenkel-Kontorova model, and the other segment is a three-dimensional Fermi-Pasta-Ulam model. We study the vibrational bands of the two lattices analytically and numerically, and find that, by choosing the system parameters properly, the rectification can be as high as a few thousands, which is high enough to be observed in experiment. Possible experiments in nanostructures are discussed

  17. Dual Phase Change Thermal Diodes for Enhanced Rectification Ratios: Theory and Experiment

    KAUST Repository

    Cottrill, Anton L.; Wang, Song; Liu, Albert Tianxiang; Wang, Wen-Jun; Strano, Michael S.

    2018-01-01

    Thermal diodes are materials that allow for the preferential directional transport of heat and are highly promising devices for energy conservation, energy harvesting, and information processing applications. One form of a thermal diode consists of the junction between a phase change and phase invariant material, with rectification ratios that scale with the square root of the ratio of thermal conductivities of the two phases. In this work, the authors introduce and analyse the concept of a Dual Phase Change Thermal Diode (DPCTD) as the junction of two phase change materials with similar phase boundary temperatures but opposite temperature coefficients of thermal conductivity. Such systems possess a significantly enhanced optimal scaling of the rectification ratio as the square root of the product of the thermal conductivity ratios. Furthermore, the authors experimentally design and fabricate an ambient DPCTD enabled by the junction of an octadecane-impregnated polystyrene foam, polymerized using a high internal phase emulsion template (PFH-O) and a poly(N-isopropylacrylamide) (PNIPAM) aqueous solution. The DPCTD shows a significantly enhanced thermal rectification ratio both experimentally (2.6) and theoretically (2.6) as compared with ideal thermal diodes composed only of the constituent materials.

  18. Dual Phase Change Thermal Diodes for Enhanced Rectification Ratios: Theory and Experiment

    KAUST Repository

    Cottrill, Anton L.

    2018-01-15

    Thermal diodes are materials that allow for the preferential directional transport of heat and are highly promising devices for energy conservation, energy harvesting, and information processing applications. One form of a thermal diode consists of the junction between a phase change and phase invariant material, with rectification ratios that scale with the square root of the ratio of thermal conductivities of the two phases. In this work, the authors introduce and analyse the concept of a Dual Phase Change Thermal Diode (DPCTD) as the junction of two phase change materials with similar phase boundary temperatures but opposite temperature coefficients of thermal conductivity. Such systems possess a significantly enhanced optimal scaling of the rectification ratio as the square root of the product of the thermal conductivity ratios. Furthermore, the authors experimentally design and fabricate an ambient DPCTD enabled by the junction of an octadecane-impregnated polystyrene foam, polymerized using a high internal phase emulsion template (PFH-O) and a poly(N-isopropylacrylamide) (PNIPAM) aqueous solution. The DPCTD shows a significantly enhanced thermal rectification ratio both experimentally (2.6) and theoretically (2.6) as compared with ideal thermal diodes composed only of the constituent materials.

  19. Controllable magnetic thermal rectification in a SMM dimmer with the Dzyaloshinskii-Moriya interaction

    Science.gov (United States)

    Xu, Ai-Hua; Liu, Juan; Luo, Bo

    2016-10-01

    Using the quantum master equation, we studied the thermally driven magnonic spin current in a single-molecule magnet (SMM) dimer with the Dzyaloshinskii-Moriya interaction (DMI). Due to the asymmetric DMI, one can observe the thermal rectifying effect in the case of the spatial symmetry coupling with the thermal reservoirs. The properties of the thermal rectification can be controlled by tuning the angle and intensity of the magnetic field. Specially, when the DM vector and magnetic field point at the specific angles, the thermal rectifying effect disappears. And this phenomenon does not depend on the intensities of DMI and magnetic field, the temperature bias and the magnetic anisotropies of the SMM.

  20. Rectification of electronic heat current by a hybrid thermal diode.

    Science.gov (United States)

    Martínez-Pérez, Maria José; Fornieri, Antonio; Giazotto, Francesco

    2015-04-01

    Thermal diodes--devices that allow heat to flow preferentially in one direction--are one of the key tools for the implementation of solid-state thermal circuits. These would find application in many fields of nanoscience, including cooling, energy harvesting, thermal isolation, radiation detection and quantum information, or in emerging fields such as phononics and coherent caloritronics. However, both in terms of phononic and electronic heat conduction (the latter being the focus of this work), their experimental realization remains very challenging. A highly efficient thermal diode should provide a difference of at least one order of magnitude between the heat current transmitted in the forward temperature (T) bias configuration (Jfw) and that generated with T-bias reversal (Jrev), leading to ℛ = Jfw/Jrev ≫ 1 or ≪ 1. So far, ℛ ≈ 1.07-1.4 has been reported in phononic devices, and ℛ ≈ 1.1 has been obtained with a quantum-dot electronic thermal rectifier at cryogenic temperatures. Here, we show that unprecedentedly high ratios of ℛ ≈ 140 can be achieved in a hybrid device combining normal metals tunnel-coupled to superconductors. Our approach provides a high-performance realization of a thermal diode for electronic heat current that could be successfully implemented in true low-temperature solid-state thermal circuits.

  1. Conjunction of standing wave and resonance in asymmetric nanowires: a mechanism for thermal rectification and remote energy accumulation.

    Science.gov (United States)

    Liu, Yue-Yang; Zhou, Wu-Xing; Chen, Ke-Qiu

    2015-12-02

    As an important way to control and manage heat transport, thermal rectification has become an elementary issue in the field of phononics and plays a key role in the designing of thermal devices. Here we investigate systematically the standing wave and the accompanying resonance process in asymmetric nanowires to understand the standing wave itself and its great effect on thermal rectification. Results show that the standing wave is sensitive to both the structural and thermal properties of the material, and its great effect on enhancing the thermal rectification is realized not only by the energy-localization nature of the standing wave, but also by the resonance-caused large amplitude and high energy of the standing wave.

  2. High Thermal Rectifications Using Liquid Crystals Confined into a Conical Frustum

    Science.gov (United States)

    Silva, José Guilherme; Fumeron, Sébastien; Moraes, Fernando; Pereira, Erms

    2018-05-01

    In recent years, phononics, that studies thermal analogs of electronic devices, has become an important subject due to the need for better use of energy resources influenced by growing demand. On developing of these analogs, for example, thermal diodes, a successful route is the design of nanostructured materials (e.g., carbon nanotubes). However, these materials entail increased costs due to the use of complex techniques/equipments, while alternative cheaper materials present nearly comparable efficiency. In this work, we investigate how a thermal diode made by an alternative material (nematic liquid crystal), confined in a conical frustum capillary, can be optimized to achieve high rectifications. In such capillary tube, the thermotropic nematic liquid crystal 5CB produces an axially anisotropic defect called escaped radial disclination. With the molecular director field of such structure, we obtain the thermal conductivity tensor of the diode and solve the steady-state regime of Laplace and Fourier equations using the finite element method. We observed the anisotropy of the system with the non-linear temperature dependences of the molecular thermal conductivities that rectify the heat flux at rates up to 1266% at room temperature. Studying the sensitivity of the system with respect to shape and molecular and thermal aspects, we found that the improved thermal diode is suitable to be miniaturized and applied on well-determined areas, and it is robust against variations of the inward pumped heat flux. This work contributes to the usage of liquid crystals in non-display devices, having potential applications on controlling the heat flux through surfaces.

  3. Tunable thermal rectification in graphene/hexagonal boron nitride hybrid structures

    Science.gov (United States)

    Chen, Xue-Kun; Hu, Ji-Wen; Wu, Xi-Jun; Jia, Peng; Peng, Zhi-Hua; Chen, Ke-Qiu

    2018-02-01

    Using non-equilibrium molecular dynamics simulations, we investigate thermal rectification (TR) in graphene/hexagonal boron nitride (h-BN) hybrid structures. Two different structural models, partially substituting graphene into h-BN (CBN) and partially substituting h-BN into graphene (BNC), are considered. It is found that CBN has a significant TR effect while that of BNC is very weak. The observed TR phenomenon can be attributed to the resonance effect between out-of-plane phonons of graphene and h-BN domains in the low-frequency region under negative temperature bias. In addition, the influences of ambient temperature, system size, defect number and substrate interaction are also studied to obtain the optimum conditions for TR. More importantly, the TR ratio could be effectively tuned through chemical and structural diversity. A moderate C/BN ratio and parallel arrangement are found to enhance the TR ratio. Detailed phonon spectra analyses are conducted to understand the thermal transport behavior. This work extends hybrid engineering to 2D materials for achieving TR.

  4. Rectification of leak from upper aluminium thermal shield cooling water inlet line of Cirus reactor

    International Nuclear Information System (INIS)

    Bhatnagar, Anil; Joshi, N.S.; Kharpate, A.V.; Marik, S.K.

    2006-01-01

    During 1994, a small water leak was observed from the upper aluminium thermal shield of Cirus reactor. Detailed investigations revealed that the leakage was from the weld joint of one of the 1 1/4 inch NB Sch. 80 coolant inlet pipes connected to the upper aluminium thermal shield. The location of the leak was identified by monitoring the stabilised water level in the vertical inlet pipe under stagnant condition. The exact location was identified by installing an inflatable seal arrangement inside the leaky pipe and inflating the seal at different elevations to isolate the leaky location and ensuring that the leak was completely stopped. This location was about 15 feet below the operating floor of the reactor. The pipe was visually inspected with the help of a fibre-scope to assess the condition of the inner surface. Eddy current testing was also carried out for volumetric examination. This revealed one more localised flaw on the outer surface little above the leaky joint. A hollow plug, with expandable rings, having C-shaped cross section at both the ends and a straight portion in the middle to cover the defective region, was developed and qualified in a mock-up station after extensive trials. In view of the site constraints, a flexible hollow link assembly was engineered, for installing the plug remotely. The inner surface of the pipe was cleaned using an emery brush and a deburring tool. The plug was then installed covering the leak area and the rings were expanded by remote tightening. The shield was hydro-tested satisfactorily. (author)

  5. Synthesis and characterization of oligobenzimidazoles: Electrochemical, electrical, optical, thermal and rectification properties

    Science.gov (United States)

    Anand, Siddeswaran; Muthusamy, Athianna

    2018-03-01

    A series of benzimidazole monomers, (2-(2, 4-dihydroxyphenyl)-1H-benzimidazol-5-yl)(phenyl) methanone (BIKH), 2-(3-ethoxy-2-hydroxyphenyl)-1H-benzo [d]imidazole-5-yl) (phenyl) methanone (BIKE) and 2-(5-bromo-2-hydroxyphenyl)-1H-benzo [d]imidazole-5-yl) (phenyl) methanone (BIKB) were prepared by condensing three substituted aromatic aldehydes with 3, 4-diaminobenzophenone. In aqueous alkaline medium the benzimidazoles were converted in to oligomers by oxidative polycondensation using NaOCl as oxidant. The formation of monomers and oligomers were confirmed with 1H, 13C NMR, FT-IR, and UV-visible spectroscopic techniques. The oligomers were investigated for their optical, electrical, electrochemical and thermal properties. The electrochemical and optical band gaps of monomers and oligomers were calculated using both UV-visible spectroscopy and cyclic voltametry respectively. The band gap values of monomers are compared with band gap values obtained from quantum theoretical calculations with DFT. The electrical conductivity studies of iodine doped and undoped oligomers were done using two point probe technique. It is found that these values are showing good correlation with the charge densities on imidazole nitrogen obtained from Huckel method. The conductivity of oligomers increases with increase in iodine vapour contact time. The dielectric properties of oligomers have been investigated at different temperature and frequency. The dielectric measurement data were used to calculate the AC conductivity and activation energy of oligomers. Oligomer OBIKH is having greater thermal stability due to its number of chain propagation sites than other oligomers and is shown by its high carbines residue of around 60% at 600 °C in thermogravimetric analysis. I-V characteristics of oligobenzimidazole p-n diodes have shown good rectifying nature in the range -4 to 4 V.

  6. The utilisation of thermal analysis to optimise radiocarbon dating procedures

    International Nuclear Information System (INIS)

    Brandova, D.; Keller, W.A.; Maciejewski, M.

    1999-01-01

    Thermal analysis combined with mass spectrometry was applied to radiocarbon dating procedures (age determination of carbon-containing samples). Experiments carried out under an oxygen atmosphere were used to determine carbon content and combustion range of soil and wood samples. Composition of the shell sample and its decomposition were investigated. The quantification of CO 2 formed by the oxidation of carbon was done by the application of pulse thermal analysis. Experiments carried out under an inert atmosphere determined the combustion range of coal with CuO as an oxygen source. To eliminate a possible source of contamination in the radiocarbon dating procedures the adsorption of CO 2 by CuO was investigated. (author)

  7. Fractionation and rectification apparatus

    Energy Technology Data Exchange (ETDEWEB)

    Sauerwald, A

    1932-05-25

    Fractionation and rectifying apparatus with a distillation vessel and a stirring tube, drainage tubes leading from its coils to a central collecting tube, the drainage tubes being somewhat parallel and attached to the outer half of the stirring tube and partly on the inner half of the central collecting tube, whereby distillation and rectification can be effected in a single apparatus.

  8. U-series dating using thermal ionisation mass spectrometry (TIMS)

    International Nuclear Information System (INIS)

    McCulloch, M.T.

    1999-01-01

    U-series dating is based on the decay of the two long-lived isotopes 238 U(τ 1/2 =4.47 x 10 9 years) and 235 U (τ 1/2 0.7 x 10 9 years). 238 U and its intermediate daughter isotopes 234 U (τ 1/2 = 245.4 ka) and 230 Th (τ 1/2 = 75.4 ka) have been the main focus of recently developed mass spectrometric techniques (Edwards et al., 1987) while the other less frequently used decay chain is based on the decay 235 U to 231 Pa (τ 1/2 = 32.8 ka). Both the 238 U and 235 U decay chains terminate at the stable isotopes 206 Pb and 207 Pb respectively. Thermal ionization mass spectrometry (TIMS) has a number of inherent advantages, mainly the ability to measure isotopic ratios at high precision on relatively small samples. In spite of these now obvious advantages, it is only since the mid-1980's when Chen et al., (1986) made the first precise measurements of 234 U and 232 Th in seawater followed by Edwards et al., (1987) who made combined 234 U- 230 Th measurements, was the full potential of mass spectrometric methods first realised. Several examples are given to illustrate various aspects of TIMS U-series

  9. U-series dating using thermal ionisation mass spectrometry (TIMS)

    Energy Technology Data Exchange (ETDEWEB)

    McCulloch, M.T. [Australian National University, Canberra, ACT (Australia). Research School of Earth Science

    1999-11-01

    U-series dating is based on the decay of the two long-lived isotopes{sup 238}U({tau}{sub 1/2}=4.47 x 10{sup 9} years) and {sup 235}U ({tau}{sub 1/2} 0.7 x 10{sup 9} years). {sup 238}U and its intermediate daughter isotopes {sup 234}U ({tau}{sub 1/2} = 245.4 ka) and {sup 230}Th ({tau}{sub 1/2} = 75.4 ka) have been the main focus of recently developed mass spectrometric techniques (Edwards et al., 1987) while the other less frequently used decay chain is based on the decay {sup 235}U to {sup 231}Pa ({tau}{sub 1/2} = 32.8 ka). Both the {sup 238}U and {sup 235}U decay chains terminate at the stable isotopes {sup 206}Pb and {sup 207}Pb respectively. Thermal ionization mass spectrometry (TIMS) has a number of inherent advantages, mainly the ability to measure isotopic ratios at high precision on relatively small samples. In spite of these now obvious advantages, it is only since the mid-1980`s when Chen et al., (1986) made the first precise measurements of {sup 234}U and {sup 232}Th in seawater followed by Edwards et al., (1987) who made combined {sup 234}U-{sup 230}Th measurements, was the full potential of mass spectrometric methods first realised. Several examples are given to illustrate various aspects of TIMS U-series 9 refs., 3 figs.

  10. Influence of thermal treatments on radiocarbon dating of groundwater samples

    Science.gov (United States)

    Stanciu, Iuliana Madalina; Sava, Tiberiu Bogdan; Pacesila, Doru Gheorghe; Gaza, Oana; Simion, Corina Anca; Stefan, Bianca Maria; Sava, Gabriela Odilia; Ghita, Dan Gabriel; Mosu, Vasile

    2017-06-01

    Radiocarbon measurements of dissolved inorganic carbon (DIC) in water provides information about the formation of oceanic circulation of the water volumes, the hydrogeological systems, and also valuable information can be gained about the aquifer storage and the degree of containment relative to the surface waters. Radiocarbon dating refers to the determination of small quantities of the naturally occurring carbon 14 in the water, which can be integrated in the groundwater mass through the gaseous CO2, carbonaceous deposits dissolved by water and organic remains. The aim of this study is to investigate the influence of the temperature and pressure over the amount of each isotope of carbon during the sample preparation stage. The first step was to evaporate several underground water samples at 65°C under different conditions until the carbonates were obtained, then the CO2 was extracted with orto-phosphoric acid and transformed to graphite. The second step was to obtain graphite from an untreated water sample. Finally, the samples were measured with the 1MV Cockcroft-Walton Tandetron Accelerator by Accelerator Mass Spectrometry.

  11. Thermal activation and radiation quenching effects in pre-dose dating of porcelain

    International Nuclear Information System (INIS)

    Wang Weida; Xia Junding

    2005-01-01

    The pre-dose technique is very useful for thermoluminescence dating of porcelain. It incorporates two characteristics in the porcelain dating, i.e. thermal activation and radiation quenching. Two methods, activation method and quenching method, for evaluation of paleodose were introduced. The results show that activation method and quenching method one suitable for dating of lower limit age (less than 100 years B.P.) and upper limit age (greater than 1000 years B.P.), respectively. When both methods are co-used, the dating will be more accurate. (authors)

  12. Separation processes, I: Azeotropic rectification

    Directory of Open Access Journals (Sweden)

    Milojević Svetomir

    2005-01-01

    Full Text Available In a series of two articles, the problems of azeotrope separation (part I and the design of separation units (part II were analyzed. The basic definition and equations of vapour-liquid equilibria for ideal and non-ideal systems, the importance of the activity coefficient calculation necessary for the analysis of non-ideal equilibrium systems, as well as theoretical aspects of azeotrope rectification and the determination of the optimal third component (modifier or azeotrope agent are presented in the first part.

  13. Local rectification of heat flux

    Science.gov (United States)

    Pons, M.; Cui, Y. Y.; Ruschhaupt, A.; Simón, M. A.; Muga, J. G.

    2017-09-01

    We present a chain-of-atoms model where heat is rectified, with different fluxes from the hot to the cold baths located at the chain boundaries when the temperature bias is reversed. The chain is homogeneous except for boundary effects and a local modification of the interactions at one site, the “impurity”. The rectification mechanism is due here to the localized impurity, the only asymmetrical element of the structure, apart from the externally imposed temperature bias, and does not rely on putting in contact different materials or other known mechanisms such as grading or long-range interactions. The effect survives if all interaction forces are linear except the ones for the impurity.

  14. Thermal Rectification in Graded Nonlinear Transmission Lines

    International Nuclear Information System (INIS)

    Xu Wen; Chen Wei-Zhong; Tao Feng

    2011-01-01

    We consider heat conduction in a nonlinear inductance-capacitance (LC) transmission line with an inductance gradient by adding white-noise signals. It is found that the heat flux in the direction of inductance decrease is larger than that in the direction of inductance increase. When the low-inductance end is at higher temperature, the phonon density decreases due to conversion to high-frequency phonons, which can not move to the high-inductance end due to its lower cutoff frequency. However, when the high-inductance end is at higher temperature, the loss of phonon density can be compensated for because some high-frequency phonons can move to the low-inductance end dur to its higher cutoff frequency. This leads to the asymmetry of energy transfer. Discussion shows that this asymmetry exists in a particular range of temperatures, and increases with the increase of the difference between heat baths and the inductance gradient. (fundamental areas of phenomenology(including applications))

  15. Current rectification by mediating electroactive polymers

    Energy Technology Data Exchange (ETDEWEB)

    Ybarra, Gabriel; Moina, Carlos [Centro de Investigacion sobre Electrodeposicion y Procesos Superficiales, Instituto Nacional de Tecnologia Industrial, CC 157, (1650) San Martin (Argentina); Florit, M. Ines [INIFTA, Facultad de Ciencias Exactas, UNLP, Suc. 4, CC 16, (1900) La Plata (Argentina); Posadas, Dionisio [INIFTA, Facultad de Ciencias Exactas, UNLP, Suc. 4, CC 16, (1900) La Plata (Argentina)], E-mail: dposadas@inifta.unlp.edu.ar

    2008-04-20

    In this work we briefly review the theoretical basis for the electrochemical rectification in mediated redox reactions at redox polymer modified electrodes. Electrochemical rectification may have two distinct origins. It is either caused by a slow kinetics of the reaction between the external redox couple and the mediator or it is originated by a slow electronic transport within the film under an unfavorable thermodynamic condition. We show experimental results for the redox mediation reaction of poly(o-aminophenol) (POAP) on the Fe{sup 2+/3+} and on the Fe(CN){sub 6}{sup 3-/4-} redox couples in solution that prove the proposed mechanisms of electrochemical rectification.

  16. Current rectification by mediating electroactive polymers

    International Nuclear Information System (INIS)

    Ybarra, Gabriel; Moina, Carlos; Florit, M. Ines; Posadas, Dionisio

    2008-01-01

    In this work we briefly review the theoretical basis for the electrochemical rectification in mediated redox reactions at redox polymer modified electrodes. Electrochemical rectification may have two distinct origins. It is either caused by a slow kinetics of the reaction between the external redox couple and the mediator or it is originated by a slow electronic transport within the film under an unfavorable thermodynamic condition. We show experimental results for the redox mediation reaction of poly(o-aminophenol) (POAP) on the Fe 2+/3+ and on the Fe(CN) 6 3-/4- redox couples in solution that prove the proposed mechanisms of electrochemical rectification

  17. Thermal Behaviour of Five Different Date Palm Residues of Algeria by Thermogravimetric Analysis

    Directory of Open Access Journals (Sweden)

    Siham AMIROU

    2013-06-01

    Full Text Available Renewable energy has become moreimportant globally especially with the current fuel andeconomic crisis. Date palm biomasses are highlypotential materials for energy resources. The factthat they are renewable and abundantly availableare amongst the attractive reasons of employingthem as the major source for renewable energy. Thepurpose of this research was to investigate thethermal behavior of date palm biomass in order toevaluate their usefulness for energy production. Inmicroparticular scale, the thermogravimetric analysis(TGA is one of the techniques used to determinethe thermal properties of five different date palmresidues that were studied: (date palm rachis (DPR,date palm trunk (DPT, leaf base (Petiole (LB,fruitstalk prunings (FP and liff (LP. The TGAtechnique consists to record the lost weight duringthe increase in temperature from 20°C until 600°Cwith a 10°C/min heating rate. The thermogramspresented a departure phase of free water (fromroom temperature to 110°C before the degradationprocess of the lignocellulosic constituents. The ligninand hemicellulose play an important role on thedegradation of lignocellulosic materials at thetemperature under 250°C. The degradation ofcellulose begins at 250°C and overlaps to that oflignin until 450°C.

  18. Thermal conductivity of cement stabilized earth bricks reinforced with date palm fiber

    Science.gov (United States)

    Berrehail, Tahar; Zemmouri, Noureddine; Agoudjil, Boudjemaa

    2018-05-01

    Recently, some cheap materials are available and adaptable to climate seem to meet current requirements. This paper investigates the thermal and mechanical properties of cement stabilized earth bricks(CSEB) reinforced with date palm fibers (DPF). The main goal is to develop and expand the field of use of these materials in the construction sector, and investigate the possibility of new bio composite as renewable, insulating building material with low cost, made of earth and reinforced with palm wood waste. In this study, a particular interest is brought to the thermal and mechanical characteristics, which constitute a decisive character for the choice of a building material. A series of earthen samples stabilized at 5% and reinforced with DPF of various fiber weight fractions, (5%, 10%), were manufactured and compacted applying two levels compacting, (5MPa and 10MPa). Compressive strength and thermal conductivity were experimentally studied; heating capacity and diffusivity were indirectly calculated. It was found that the fibrous reinforcement proved thermal conductivity and compressive strength. it also enhanced thermal performances. Thus, the results found allow us to investigate hygrothermal behaviour and its impact on occupants comfort.

  19. Desactivation of tritium waters by rectification methods

    International Nuclear Information System (INIS)

    Egorov, A.I.; Tyunis, V.M.

    2002-01-01

    Results of experiments into the basic rectification processes dedicated to tritium separation from reactor, technological and waste waters are presented. Coefficients of separation for rectification of water (1.028), ammonia (1.05), azeotrope H 2 O - HTO - HNO 3 (1.098) and D 2 O - DTO - DNO 3 (1.039) are performed. Operating schemes of tritium separating units are reviewed [ru

  20. Mechanical and thermal properties of date palm leaf fiber reinforced recycled poly (ethylene terephthalate) composites

    International Nuclear Information System (INIS)

    Dehghani, Alireza; Madadi Ardekani, Sara; Al-Maadeed, Mariam A.; Hassan, Azman; Wahit, Mat Uzir

    2013-01-01

    Highlights: • A novel natural fiber reinforced recycled poly (ethylene terephthalate) composite was prepared. • Mechanical performance and thermal behavior of the composites were investigated. • Composites with improved toughness and strength were achieved. - Abstract: Development of a recycled poly (ethylene terephthalate) (PETr) reinforced with surface treated date palm leaf fiber (DPLF) composites with enhanced mechanical properties have been studied. Surface modified date palm leaf fiber reinforced PETr composites were prepared using twin-screw extruder followed by injection molding and the influence of the DPLF content on the mechanical and thermal behavior of the PETr matrix was evaluated. Upon the addition of fibers, remarkable enhancements in the mechanical properties of the composites were observed. Scanning electron microscopy (SEM) images taken from DPLF fibers showed significant enhancements in the fiber’s surface topography after the surface treatment process. Dynamic mechanical analysis (DMA) indicated that the addition of DPLF to PETr matrix increased the composites toughness. The crystallization behavior of the samples, analyzed by differential scanning calorimetry (DSC) indicated an increase in the onset crystallization temperature and showed a higher degree of crystallinity of the composites as compared to PETr, demonstrating that DPLF particles could act as nucleating agents. The results point to the composite’s potential in wider indoor applications

  1. Date palm biochar-polymer composites: An investigation of electrical, mechanical, thermal and rheological characteristics.

    Science.gov (United States)

    Poulose, Anesh Manjaly; Elnour, Ahmed Yagoub; Anis, Arfat; Shaikh, Hamid; Al-Zahrani, S M; George, Justin; Al-Wabel, Mohammad I; Usman, Adel R; Ok, Yong Sik; Tsang, Daniel C W; Sarmah, Ajit K

    2018-04-01

    The application of biochar (BC) as a filler in polymers can be viewed as a sustainable approach that incorporates pyrolysed waste based value-added material and simultaneously mitigate bio-waste in a smart way. The overarching aim of this work was to investigate the electrical, mechanical, thermal and rheological properties of biocomposite developed by utilizing date palm waste-derived BC for the reinforcing of polypropylene (PP) matrix. Date palm waste derived BC prepared at (700 and 900°C) were blended at different proportions with polypropylene and the resultant composites (BC/PP) were characterized using an array of techniques (scanning electron microscope, energy-dispersive X-ray spectroscopy and Fourier transform infra-red spectroscopy). Additionally the thermal, mechanical, electrical and rheological properties of the BC/PP composites were evaluated at different loading of BC content (from 0 to15% w/w). The mechanical properties of BC/PP composites showed an improvement in the tensile modulus while that of electrical characterization revealed an enhanced electrical conductivity with increased BC loading. Although the BC incorporation into the PP matrix has significantly reduced the total crystallinity of the resulted composites, however; a positive effect on the crystallization temperature (T c ) was observed. The rheological characterization of BC/PP composites revealed that the addition of BC had minimal effect on the storage modulus (G') compared to the neat (PP). Copyright © 2017 Elsevier B.V. All rights reserved.

  2. Absolute measurement of thermal neutron fluence and its application for fission track dating

    International Nuclear Information System (INIS)

    Ganzawa, Yoshihiro; Honda, Teruyuki; Nozaki, Tetsuya.

    1988-01-01

    The absolute measurements of thermal neutron fluence for fission track dating have been developed after the proceeding results of Honda et al. (1987). The 2,200 m/sec activation cross section of 197 Au (98.8 barn) is corrected to 87.4 barn (σa) by the three factors of the neutron temperature, Maxwellian distribution of thermal neutrons and non 1/v correction factor for the above absolute measurement. The calibrated factor (B th ) of standard glasses (SRM613, SRM962a, CN-1 and CN-2) and zeta-a (ζa) values for fission track dating are determined on the basis of these experimental results. The values of B th , (7.47 ± 0.29) x 10 9 for SRM613, (7.43 ± 0.34) x 10 9 for SRM962a, (2.50 ± 0.06) x 10 9 for CN-1 and (2.74 ± 0.06) x 10 9 for CN-2 closely agree with those reported previously by Honda et al. (1987). Further, the ζa values of 392.3 ± 16.5 for SRM962a and SRM613, 131.4 ± 3.1 for CN-1 and 144.1 ± 3.3 for CN-2 calculated from B th , effective thermal neutron fission cross-section σf (497.4 barn), isotopic abundance ratio 235 U/ 239 U, I (7.2527 x 10 -3 ) and spontaneous fission decay constant of 238 U, λ f (6.85 x 10 -17 a -7 ) show close agreement with ζ b values (392.5 ± 10.0, 131.6 ± 3.3, 140.1 ± 3.5) derived from the absolute age of Fish Canyon Tuff (27.9 ± 0.7 Ma) respectively. The fission track dating of zircons separated from Oligocene-Miocene tuff distributed in Eastern Hokkaido have been carried out by the external detector method using ζ a . The obtained ages are 28.6 ± 0.7 Ma (1 - 2) and 23.3 ± 0.7 Ma (3 - 2). These results agree well with the geologic age supported from Ashoro Fossil Fauna, K-Ar ages of volcanic rocks and stratigraphy in this area. (author)

  3. Energy-Saving in Brew-Rectification

    Directory of Open Access Journals (Sweden)

    N. I. Ulyanau

    2008-01-01

    Full Text Available The paper investigates dynamics of rectification process on one plate of a column. The basic channels controlling brew-rectification process are described in the paper.The paper also considers problems pertaining to synthesis of an adaptive system that controls non-stationary objects with delay. Synthesis of adaptive systems that automatically control product quality and saving on power resources and productivity with the help of the second method of Lyapunov has been carried out in the paper.Industrial introduction of the given automatic control system of technological process shall permit to increase productivity of a rectification (10–15 %, to decrease specific power consumption by (5–10 % while preserving the specified quality of rectified ethyl alcohol and decrease alcohol losses with luting water and malt-residue.

  4. Precision Rectification of Airborne SAR Image

    DEFF Research Database (Denmark)

    Dall, Jørgen; Liao, M.; Zhang, Zhe

    1997-01-01

    A simple and direct procedure for the rectification of a certain class of airborne SAR data is presented. The relief displacements of SAR data are effectively removed by means of a digital elevation model and the image is transformed to the ground coordinate system. SAR data from the Danish EMISAR...

  5. The thermal history of the Lhasa Block, South Tibetan Plateau based on FTD and Ar-Ar dating

    CERN Document Server

    Yang, T F; Lo Chong Huah; Chung, S L; Tien, R L; Xu, R; Deng, W

    1999-01-01

    Twelve basement samples were collected from South Tibet Plateau for FTD and Ar-Ar analysis to demonstrate their uplifting history since Cenozoic era. The preliminary results from different minerals with different closure temperatures, including apatite and zircon for fission-track dating, and K-feldspar, biotite for Ar-Ar dating, show that at least four stages of thermal history can be recognized in the studied area.

  6. The thermal history of the Lhasa Block, South Tibetan Plateau based on FTD and Ar-Ar dating

    International Nuclear Information System (INIS)

    Yang, T.F.; Wang, J.R.; Lo, C.H.; Chung, S.L.; Tien, R.L.; Xu, R.; Deng, W.

    1999-01-01

    Twelve basement samples were collected from South Tibet Plateau for FTD and Ar-Ar analysis to demonstrate their uplifting history since Cenozoic era. The preliminary results from different minerals with different closure temperatures, including apatite and zircon for fission-track dating, and K-feldspar, biotite for Ar-Ar dating, show that at least four stages of thermal history can be recognized in the studied area

  7. Thermal history of the Acoculco geothermal system, eastern Mexico: Insights from numerical modeling and radiocarbon dating

    Science.gov (United States)

    Canet, Carles; Trillaud, Frederic; Prol-Ledesma, Rosa María; González-Hernández, Galia; Peláez, Berenice; Hernández-Cruz, Berenice; Sánchez-Córdova, María M.

    2015-10-01

    Acoculco is a geothermal prospective area hosted by a volcanic caldera complex in the eastern Trans-Mexican Volcanic Belt. Surface manifestations are scarce and consist of gas discharges (CO2-rich) and acid-sulfate springs of low temperature, whereas hydrothermal explosive activity is profusely manifested by meter-scale craters and mounds of hydrothermal debris and breccias. Silicic alteration extends for several square kilometers around the zone with gas manifestations and explosive features, affecting surficial volcanic rocks, primarily tuffs and breccias. In the subsurface, an argillic alteration zone (ammonium illite) extends down to a depth of ∼ 600 m, and underneath it a propylitic zone (epidote-calcite-chlorite) occurs down to ∼ 1000 m. Thermal logs from an exploratory borehole (EAC-1, drilled in 1995 down to 1810 m) showed a conductive heat transfer regime under high geothermal gradient (∼ 140 °C/1000 m). In contrast, the thermal profile established from temperatures of homogenization of fluid inclusions-measured on core samples from the same drill hole-suggests that convection occurred in the past through the upper ~ 1400 m of the geothermal system. A drop in permeability due to the precipitation of alteration minerals would have triggered the cessation of the convective heat transfer regime to give place to a conductive one. With the purpose of determining when the transition of heat transfer regime occurred, we developed a 1D model that simulates the time-depth distribution of temperature. According to our numerical simulations, this transition happened ca. 7000 years ago; this date is very recent compared to the lifespan of the geothermal system. In addition, radiocarbon chronology indicates that the hydrothermal explosive activity postdates the end of the convective heat transfer regime, having dated at least three explosive events, at 4867-5295, 1049-1417 and 543-709 y cal. BP. Therefore, hydrothermal explosions arise from the self-sealing of

  8. Large rectification magnetoresistance in nonmagnetic Al/Ge/Al heterojunctions.

    Science.gov (United States)

    Zhang, Kun; Li, Huan-Huan; Grünberg, Peter; Li, Qiang; Ye, Sheng-Tao; Tian, Yu-Feng; Yan, Shi-Shen; Lin, Zhao-Jun; Kang, Shi-Shou; Chen, Yan-Xue; Liu, Guo-Lei; Mei, Liang-Mo

    2015-09-21

    Magnetoresistance and rectification are two fundamental physical properties of heterojunctions and respectively have wide applications in spintronics devices. Being different from the well known various magnetoresistance effects, here we report a brand new large magnetoresistance that can be regarded as rectification magnetoresistance: the application of a pure small sinusoidal alternating-current to the nonmagnetic Al/Ge Schottky heterojunctions can generate a significant direct-current voltage, and this rectification voltage strongly varies with the external magnetic field. We find that the rectification magnetoresistance in Al/Ge Schottky heterojunctions is as large as 250% at room temperature, which is greatly enhanced as compared with the conventional magnetoresistance of 70%. The findings of rectification magnetoresistance open the way to the new nonmagnetic Ge-based spintronics devices of large rectification magnetoresistance at ambient temperature under the alternating-current due to the simultaneous implementation of the rectification and magnetoresistance in the same devices.

  9. Characterization of date palm frond as a fuel for thermal conversion processes

    Directory of Open Access Journals (Sweden)

    Sadig Hussain

    2017-01-01

    Full Text Available Date palm fronds (DPF have similar physical appearances to those of oil palm fronds and coconut palm fronds, which have been reported as having good potential as a source of energy through thermochemical conversion of biomass. However, nearly no report has been found pertaining to thermochemical properties of DPF. Hence, it has remained unclear whether DPF can become suitable feedstock for power generation. This study investigated the characteristics of DPF as a potential solid fuel for heat and power generation through various thermal conversion processes. DPF samples from selected sites in Sudan and Saudi Arabia were tested. The ultimate and proximate analyses and the calorific value of DPF were measured, and the results were compared with low to medium-rank coals and other common biomass materials. The calorific value range for DPF samples was found to be between 16.2 to 16.9 MJ/kg. The ultimate analysis of DPF samples revealed that more than 75% of their mass was composed of volatile materials, while the ash content in all samples was found to be less than 15%. The range of elementary carbon, hydrogen, nitrogen, sulfur and oxygen in DPF samples was found to be typical to that in biomass. The thermal decomposition trends the samples indicated the high reactivity of DPF with rising temperatures due to high holocellulose content. No distinctive differences in test results were observed between samples from Saudi Arabia and Northern Sudan. Overall, it was found that all DPF samples used in this study fulfilled the typical requirements for development and utilization as a solid fuel.

  10. Climate change impacts on crop yields, land use and environment in response to crop sowing dates and thermal time requirements

    NARCIS (Netherlands)

    Zimmermann, Andrea; Webber, Heidi; Zhao, Gang; Ewert, Frank; Kros, Hans; Wolf, Joost; Britz, Wolfgang; Vries, de Wim

    2017-01-01

    Impacts of climate change on European agricultural production, land use and the environment depend on its impact on crop yields. However, many impact studies assume that crop management remains unchanged in future scenarios, while farmers may adapt their sowing dates and cultivar thermal time

  11. Ink dating using thermal desorption and gas chromatography / mass spectrometry: comparison of results obtained in two laboratories

    OpenAIRE

    Koenig, A.; Bügler, J.; Kirsch, D.; Köhler, F.; Weyermann, C.

    2015-01-01

    Recent ink dating methods focused mainly on changes in solvent amounts occurring over time. A promising method was developed at the Landeskriminalamt of Munich using thermal desorption (TD) followed by gas chromatography / mass spectrometry (GC/MS) analysis. Sequential extractions of the phenoxyethanol present in ballpoint pen ink entries were carried out at two different temperatures. This method is applied in forensic practice and is currently implemented in several laboratories participati...

  12. Microwave power engineering generation, transmission, rectification

    CERN Document Server

    Okress, Ernest C

    1968-01-01

    Microwave Power Engineering, Volume 1: Generation, Transmission, Rectification considers the components, systems, and applications and the prevailing limitations of the microwave power technology. This book contains four chapters and begins with an introduction to the basic concept and developments of microwave power technology. The second chapter deals with the development of the main classes of high-power microwave and optical frequency power generators, such as magnetrons, crossed-field amplifiers, klystrons, beam plasma amplifiers, crossed-field noise sources, triodes, lasers. The third

  13. Enhanced heat rectification effect in a quantum dot connected to ferromagnetic leads

    Energy Technology Data Exchange (ETDEWEB)

    Chi, Feng, E-mail: chifeng@semi.ac.cn [School of Physical Science and Technology, Inner Mongolia University, Huhehaote 010023 (China); College of Engineering, Bohai University, Jinzhou 121013 (China); Sun, Lian-Liang [College of Science, North China University of Technology, Beijing 100041 (China); Zheng, Jun; Guo, Yu [College of Engineering, Bohai University, Jinzhou 121013 (China)

    2015-06-15

    We study theoretically the heat generation by electric current in an interacting single level quantum-dot connected to ferromagnetic leads. The heat is transferred between the dot and the lattice vibration of its host material (phonon reservoir). Particular attention is paid on the heat's rectification effect achieved by properly arranging the dot level and the bias voltage. We find that this effect is remarkably enhanced when the two leads' magnetic moments are in antiparallel configuration, i.e., the magnitude of the heat generation is reduced (amplified) in the negative (positive) bias regime as compared to the cases of parallel configuration and nonmagnetic leads. The rectification effect is even enhanced when one of the lead's spin polarization approaches to unit, during which the negative differential of the heat generation is weakened due to the change of the spin-dependent electron occupation numbers on the dot. The found results may be used for thermal transistor in the newly emerged research subject of phononics. - Highlights: • Heat flow between electrons and phonons is controlled by interaction between them. • A thermal diode or rectifier is proposed to work under electrical bias. • The heat rectification effect can be enhanced by the leads' ferromagnetism.

  14. Specific Mechanical Energy and Thermal Degradation of Poly(lactic acid and Poly(caprolactone/Date Pits Composites

    Directory of Open Access Journals (Sweden)

    A. A. Mohamed

    2018-01-01

    Full Text Available The compatibility of date pits (DP with polylactic acid (PLA or polycaprolactone (PCL is investigated. Composites were prepared by compounding PLA or PCL with date pits at 10, 20, 30, and 40% wt/wt and extruded. Wheat vital gluten (VG was also used as a filler and in combination with DP. The specific mechanical energy (SME was calculated and the composites thermal properties were tested using DSC (peak temperature, enthalpic relaxation, and glass transition and TGA (degradation temperature and mechanism and degradation kinetics. Because DP is hard filler, the SME of PCL-DP composites increased as the amount of filler increased. At 40% fill, the SME decreased due to the lubricating effect of oil found naturally in DP. As illustrated by lower SME, PLA composites exhibited softer texture because PLA is harder than DP. The DSC melting peak temperature of both polymers has increased at higher DP; however, PLA exhibited enthalpic relation between 66 and 68°C. The TGA profile of the composites displayed two distinct peaks versus one peak for the pure polymer. The degradation kinetics showed multistep process for the composites and one-step process for the pure polymer. The utilization of date pits as a hard filler in developing biodegradable plastics is good for the environment and a value added for the date industry.

  15. Fission track dating and thermal history of Habahe rock body in Altai

    International Nuclear Information System (INIS)

    Liu Shunsheng; Tan Kaixuan

    2002-01-01

    The fission track ages (FTA) of several apatite and zircon samples from Habahe rock body in Altai were determined. The FTA of apatites were 51.1-76.9 Ma, and FTA of zircons were 141-149 Ma. Modelling of the palaeo-temperature evolution [T(t)-path] of rock body relies on confined track length measurements and the annealing equations of Laslett et al. (1987). The thermal and uplift history of this region was discussed

  16. Rectification of light refraction in curved waveguide arrays.

    Science.gov (United States)

    Longhi, Stefano

    2009-02-15

    An "optical ratchet" for discretized light in photonic lattices, which enables observing rectification of light refraction at any input beam conditions, is theoretically presented, and a possible experimental implementation based on periodically curved zigzag waveguide arrays is proposed.

  17. Rectification of light refraction in curved waveguide arrays

    OpenAIRE

    Longhi, S.

    2010-01-01

    An 'optical ratchet' for discretized light in photonic lattices, which enables to observe rectification of light refraction at any input beam conditions, is theoretically presented, and a possible experimental implementation based on periodically-curved zigzag waveguide arrays is proposed.

  18. Apatite fission track dating and thermal history of Qing-He region in Altay Mountains

    International Nuclear Information System (INIS)

    Bao Zengkuan; Chinese Academy of Sciences, Beijing; Yuan Wanming; Dong Jinquan; Gao Shaokai

    2005-01-01

    Fission track ages (FTA) and track lengths of apatite from Qing-He diorite intrusion in Altay Mountains are measured. Apatite fission track ages of three diorite samples is range from (78±5) Ma to (95 ± 5) Ma, and the lengths of horizontal confined spontaneous fission tracks are (13.2 ± 1.2)-(13.5 ±1.3) μm. The distribution of the track length is narrow and symmetrical with a mean length of approximately 13.3 μm and a standard deviation of around 0.1 μm. The inverse modeling results show that thermal history of this region has four stages, two rapid uplift of this region still existed magmatic intrusion and tectonic movements in Yanshanian. (authors)

  19. Efficient thermal diode with ballistic spacer

    Science.gov (United States)

    Chen, Shunda; Donadio, Davide; Benenti, Giuliano; Casati, Giulio

    2018-03-01

    Thermal rectification is of importance not only for fundamental physics, but also for potential applications in thermal manipulations and thermal management. However, thermal rectification effect usually decays rapidly with system size. Here, we show that a mass-graded system, with two diffusive leads separated by a ballistic spacer, can exhibit large thermal rectification effect, with the rectification factor independent of system size. The underlying mechanism is explained in terms of the effective size-independent thermal gradient and the match or mismatch of the phonon bands. We also show the robustness of the thermal diode upon variation of the model's parameters. Our finding suggests a promising way for designing realistic efficient thermal diodes.

  20. Large rectification magnetoresistance in nonmagnetic Al/Ge/Al heterojunctions

    OpenAIRE

    Zhang, Kun; Li, Huan-huan; Grünberg, Peter; Li, Qiang; Ye, Sheng-tao; Tian, Yu-feng; Yan, Shi-shen; Lin, Zhao-jun; Kang, Shi-shou; Chen, Yan-xue; Liu, Guo-lei; Mei, and Liang-mo

    2015-01-01

    Magnetoresistance and rectification are two fundamental physical properties of heterojunctions and respectively have wide applications in spintronics devices. Being different from the well known various magnetoresistance effects, here we report a brand new large magnetoresistance that can be regarded as rectification magnetoresistance: the application of a pure small sinusoidal alternating-current to the nonmagnetic Al/Ge Schottky heterojunctions can generate a significant direct-current volt...

  1. Microscale solid-state thermal diodes enabling ambient temperature thermal circuits for energy applications

    KAUST Repository

    Wang, Song; Cottrill, Anton L.; Kunai, Yuichiro; Toland, Aubrey R.; Liu, Pingwei; Wang, Wen-Jun; Strano, Michael S.

    2017-01-01

    rectifications range from 1.18 to 1.34. We show that such devices perform reliably enough to operate in thermal diode bridges, dynamic thermal circuits capable of transforming oscillating temperature inputs into single polarity temperature differences – analogous

  2. Electrical detection of magnetization dynamics via spin rectification effects

    Energy Technology Data Exchange (ETDEWEB)

    Harder, Michael, E-mail: michael.harder@umanitoba.ca; Gui, Yongsheng, E-mail: ysgui@physics.umanitoba.ca; Hu, Can-Ming, E-mail: hu@physics.umanitoba.ca

    2016-11-23

    The purpose of this article is to review the current status of a frontier in dynamic spintronics and contemporary magnetism, in which much progress has been made in the past decade, based on the creation of a variety of micro and nanostructured devices that enable electrical detection of magnetization dynamics. The primary focus is on the physics of spin rectification effects, which are well suited for studying magnetization dynamics and spin transport in a variety of magnetic materials and spintronic devices. Intended to be intelligible to a broad audience, the paper begins with a pedagogical introduction, comparing the methods of electrical detection of charge and spin dynamics in semiconductors and magnetic materials respectively. After that it provides a comprehensive account of the theoretical study of both the angular dependence and line shape of electrically detected ferromagnetic resonance (FMR), which is summarized in a handbook format easy to be used for analysing experimental data. We then review and examine the similarity and differences of various spin rectification effects found in ferromagnetic films, magnetic bilayers and magnetic tunnel junctions, including a discussion of how to properly distinguish spin rectification from the spin pumping/inverse spin Hall effect generated voltage. After this we review the broad applications of rectification effects for studying spin waves, nonlinear dynamics, domain wall dynamics, spin current, and microwave imaging. We also discuss spin rectification in ferromagnetic semiconductors. The paper concludes with both historical and future perspectives, by summarizing and comparing three generations of FMR spectroscopy which have been developed for studying magnetization dynamics.

  3. ALD Modified Nanostructured Geometries for Rectification and MEMS Thermal Control

    Data.gov (United States)

    National Aeronautics and Space Administration — Through the introduction of paired precursor gases, thin films can be deposited on a myriad of substrates ranging from glass, polymers, aerogels, and metals – from...

  4. Graphene spin diode: Strain-modulated spin rectification

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yunhua; Wang, B., E-mail: stslyl@mail.sysu.edu.cn, E-mail: wangbiao@mail.sysu.edu.cn [Sino-French Institute of Nuclear Engineering and Technology, School of Physics and Engineering, State Key Laboratory of Optoelectronic Materials and Technologies, Sun Yat-sen University, Guangzhou 510275 (China); Liu, Yulan, E-mail: stslyl@mail.sysu.edu.cn, E-mail: wangbiao@mail.sysu.edu.cn [School of Engineering, Sun Yat-sen University, Guangzhou 510275 (China)

    2014-08-04

    Strain effects on spin transport in a ferromagnetic/strained/normal graphene junction are explored theoretically. It is shown that the spin-resolved Fermi energy range can be controlled by the armchair direction strain because the strain-induced pseudomagnetic field suppresses the current. The spin rectification effect for the bias reversal occurs because of a combination of ferromagnetic exchange splitting and the broken spatial symmetry of the junction. In addition, the spin rectification performance can be tuned remarkably by manipulation of the strains. In view of this strain-modulated spin rectification effect, we propose that the graphene-based ferromagnetic/strained/normal junction can be used as a tunable spin diode.

  5. Rapid characterizing of ferromagnetic materials using spin rectification

    International Nuclear Information System (INIS)

    Fan, Xiaolong; Wang, Wei; Wang, Yutian; Zhou, Hengan; Rao, Jinwei; Zhao, Xiaobing; Gao, Cunxu; Xue, Desheng; Gui, Y. S.; Hu, C.-M.

    2014-01-01

    Spin rectification is a powerful tool for dc electric detections of spin dynamics and electromagnetic waves. Technically, elaborately designed on-chip microwave devices are needed in order to realize that effect. In this letter, we propose a rapid characterizing approach based on spin rectification. By directly sending dynamic current into ferromagnetic films with stripe shape, resonant dc voltages can be detected along the longitudinal or transversal directions. As an example, Fe (010) films with precise crystalline structure and magnetic parameters were used to testify the reliability of such method. We investigated not only the dynamic parameters and the precise anisotropy constants of the Fe crystals but also the principle of spin rectification in this method

  6. Digital image transformation and rectification of spacecraft and radar images

    Science.gov (United States)

    Wu, S. S. C.

    1985-01-01

    The application of digital processing techniques to spacecraft television pictures and radar images is discussed. The use of digital rectification to produce contour maps from spacecraft pictures is described; images with azimuth and elevation angles are converted into point-perspective frame pictures. The digital correction of the slant angle of radar images to ground scale is examined. The development of orthophoto and stereoscopic shaded relief maps from digital terrain and digital image data is analyzed. Digital image transformations and rectifications are utilized on Viking Orbiter and Lander pictures of Mars.

  7. Thermal diode made by nematic liquid crystal

    Energy Technology Data Exchange (ETDEWEB)

    Melo, Djair, E-mail: djfmelo@gmail.com [Instituto de Física, Universidade Federal de Alagoas, Av. Lourival Melo Mota, s/n, 57072-900 Maceió, AL (Brazil); Fernandes, Ivna [Instituto de Física, Universidade Federal de Alagoas, Av. Lourival Melo Mota, s/n, 57072-900 Maceió, AL (Brazil); Moraes, Fernando [Departamento de Física, CCEN, Universidade Federal da Paraíba, Caixa Postal 5008, 58051-900, João Pessoa, PB (Brazil); Departamento de Física, Universidade Federal Rural de Pernambuco, 52171-900 Recife, PE (Brazil); Fumeron, Sébastien [Institut Jean Lamour, Université de Lorraine, BP 239, Boulevard des Aiguillettes, 54506 Vandoeuvre les Nancy (France); Pereira, Erms [Escola Politécnica de Pernambuco, Universidade de Pernambuco, Rua Benfíca, 455, Madalena, 50720-001 Recife, PE (Brazil)

    2016-09-07

    This work investigates how a thermal diode can be designed from a nematic liquid crystal confined inside a cylindrical capillary. In the case of homeotropic anchoring, a defect structure called escaped radial disclination arises. The asymmetry of such structure causes thermal rectification rates up to 3.5% at room temperature, comparable to thermal diodes made from carbon nanotubes. Sensitivity of the system with respect to the heat power supply, the geometry of the capillary tube and the molecular anchoring angle is also discussed. - Highlights: • An escaped radial disclination as a thermal diode made by a nematic liquid crystal. • Rectifying effects comparable to those caused by carbon and boron nitride nanotubes. • Thermal rectification increasing with radius and decreasing with height of the tube. • Asymmetric BCs cause rectification from the spatial asymmetry produced by the escape. • Symmetric BCs provide rectifications smaller than those yields by asymmetric BCs.

  8. Rectification And Revival Of Muslim World

    Directory of Open Access Journals (Sweden)

    M azram

    2012-01-01

    Full Text Available The present doldrums position and state of decadence, internal differences, external aggression (geographical and ideological, lack of self-confidence and dependence, illiteracy, political instability, economic disaster, lack of knowledge and wisdom, back benchers in science and technology, education, medicine, trade and business, banking system and defensive incapability of Muslim Ummah prompted me to write this article.  Although most of the Muslim nations got their independence because of their dedicated struggle and historic events and incidents but the old masters remained active for a remote control over the Muslim Ummah.  Their intellectuals and scholars, individually as well as collectively, have propagated and advised their leadership, the tactics and approaches by which Muslim Ummah can again be enslaved.  Writings of S.P. Huntington and F. Fukuyama are clear examples.  They are actively gearing the international institutions so cleverly that Muslim Ummah does not even realize their ill motives and objectives.  They brought their leadership in a confronting position with Muslim Ummah and hence threatening the world peace.  This situation prompted us to look at our principal sources of inspiration, which are, the Qur’an, Sunnah of the Prophet (SAW, and examples of the “enlightened Caliphs” and see if we could work out a seminal guidelines for our rectification  and revival.  We have gathered together some of these impressions; these are all tentative, nothing final about them, but these are here nonetheless. ABSTRAK: Kehadiran situasi kebelungguan dan  keruntuhan, perbezaan dalaman, pencerobohan luar (geografi dan ideologi, kurang keyakinan diri dan pergantungan, buta huruf, ketidakstabilan politik, bencana ekonomi, kekurangan ilmu dan hikmah, ketinggalan dalam sains dan teknologi, pendidikan, perubatan, perdagangan dan perniagaan, sistem perbankan dan ketidakupayaan pertahanan umat Islam mendorong saya untuk menulis

  9. Room temperature electrically tunable rectification magnetoresistance in Ge-based Schottky devices.

    Science.gov (United States)

    Huang, Qi-Kun; Yan, Yi; Zhang, Kun; Li, Huan-Huan; Kang, Shishou; Tian, Yu-Feng

    2016-11-23

    Electrical control of magnetotransport properties is crucial for device applications in the field of spintronics. In this work, as an extension of our previous observation of rectification magnetoresistance, an innovative technique for electrical control of rectification magnetoresistance has been developed by applying direct current and alternating current simultaneously to the Ge-based Schottky devices, where the rectification magnetoresistance could be remarkably tuned in a wide range. Moreover, the interface and bulk contribution to the magnetotransport properties has been effectively separated based on the rectification magnetoresistance effect. The state-of-the-art electrical manipulation technique could be adapt to other similar heterojunctions, where fascinating rectification magnetoresistance is worthy of expectation.

  10. Metal–semiconductor nanojunctions and their rectification ...

    Indian Academy of Sciences (India)

    Using the standard equation the difference between the work functions of the metal and the semiconductor was calculated. This showed a variation with the temperature of measurement. This is explained as arising due to the effect of pressure generated as a result of thermal expansion of the metallic phases concerned ...

  11. Investigation of the thermal stability of 210 deg. C TL peak of quartz and dating the components of terrazzo from the monastery church of Tegernsee

    International Nuclear Information System (INIS)

    Goeksu, H.Y.; Schwenk, P.; Semiochkina, N.

    2001-01-01

    The lifetime of the thermoluminescence (TL) peak of quartz observed at 210 deg. C using 5 deg. C/s heating rate is assessed using well-dated thermally isolated bricks from a monastery and exposed bricks from warmer climatic zones by comparing the absorbed dose obtained using the 210 deg. C TL peak with those obtained from 310 deg. C TL peak. The lifetimes of the 210 deg. C TL peak calculated for samples collected from thermally isolated excavations and exposed buildings are found to be clustered around 8000-10000 and 600-800 years, respectively. The results proved that 210 deg. C TL peak could be used for dating of samples younger than 1000 years without thermal correction if the samples are thermally isolated from their environment. TL ages are obtained using quartz, polyminerals from brick pieces as well as flint splinters, and other quartz inclusions extracted from the mortar of the terrazzo floor of the monastery church. The measured TL ages and the consistency of the results are discussed. The fine grains in the mortar, which contained calcite/aragonite, could not be dated using thermoluminescence due to presence of a very strong non-radiation induced TL glow

  12. Goal-oriented rectification of camera-based document images.

    Science.gov (United States)

    Stamatopoulos, Nikolaos; Gatos, Basilis; Pratikakis, Ioannis; Perantonis, Stavros J

    2011-04-01

    Document digitization with either flatbed scanners or camera-based systems results in document images which often suffer from warping and perspective distortions that deteriorate the performance of current OCR approaches. In this paper, we present a goal-oriented rectification methodology to compensate for undesirable document image distortions aiming to improve the OCR result. Our approach relies upon a coarse-to-fine strategy. First, a coarse rectification is accomplished with the aid of a computationally low cost transformation which addresses the projection of a curved surface to a 2-D rectangular area. The projection of the curved surface on the plane is guided only by the textual content's appearance in the document image while incorporating a transformation which does not depend on specific model primitives or camera setup parameters. Second, pose normalization is applied on the word level aiming to restore all the local distortions of the document image. Experimental results on various document images with a variety of distortions demonstrate the robustness and effectiveness of the proposed rectification methodology using a consistent evaluation methodology that encounters OCR accuracy and a newly introduced measure using a semi-automatic procedure.

  13. Solid state thermal rectifier

    Science.gov (United States)

    None

    2016-07-05

    Thermal rectifiers using linear nanostructures as core thermal conductors have been fabricated. A high mass density material is added preferentially to one end of the nanostructures to produce an axially non-uniform mass distribution. The resulting nanoscale system conducts heat asymmetrically with greatest heat flow in the direction of decreasing mass density. Thermal rectification has been demonstrated for linear nanostructures that are electrical insulators, such as boron nitride nanotubes, and for nanostructures that are conductive, such as carbon nanotubes.

  14. Ultrafiltration and thermal processing effects on Maillard reaction products and biological properties of date palm sap syrups (Phoenix dactylifera L.).

    Science.gov (United States)

    Makhlouf-Gafsi, Ines; Krichen, Fatma; Mansour, Riadh Ben; Mokni, Abir; Sila, Assad; Bougatef, Ali; Blecker, Christophe; Attia, Hamadi; Besbes, Souhail

    2018-08-01

    The effect of ultrafiltration process and temperature concentration on MRPs content and antioxidant, antimicrobial and cytotoxic properties of date palm sap syrups were investigated. MRPs were analyzed by HPLC. Antioxidant activity was evaluated by reducing power and DPPH free radical and H 2 O 2 scavenging activities. Antimicrobial activity was evaluated by the agar disk diffusion method. In vitro cytotoxic activity was examined by cell proliferation assay. Date sap syrups displayed strong antioxidant activities which are correlated 5HMF and 2F contents. In addition, concentration at 100 °C, unlike ultrafiltration process, enhanced significantly the antioxidant activities sap syrups and total phenolic contents. The antimicrobial activities showed marked activity against S. enterica, P. aeruginosa, S. aureus, L. monocytogenes with an inhibition zone of 21, 34, 27 and 34 mm respectively. Cytotoxicity assays showed that sap syrups can inhibit the proliferation of HeLa cell lines at high concentration. Published by Elsevier Ltd.

  15. Infrared rectification in a nanoantenna-coupled metal-oxide-semiconductor tunnel diode.

    Science.gov (United States)

    Davids, Paul S; Jarecki, Robert L; Starbuck, Andrew; Burckel, D Bruce; Kadlec, Emil A; Ribaudo, Troy; Shaner, Eric A; Peters, David W

    2015-12-01

    Direct rectification of electromagnetic radiation is a well-established method for wireless power conversion in the microwave region of the spectrum, for which conversion efficiencies in excess of 84% have been demonstrated. Scaling to the infrared or optical part of the spectrum requires ultrafast rectification that can only be obtained by direct tunnelling. Many research groups have looked to plasmonics to overcome antenna-scaling limits and to increase the confinement. Recently, surface plasmons on heavily doped Si surfaces were investigated as a way of extending surface-mode confinement to the thermal infrared region. Here we combine a nanostructured metallic surface with a heavily doped Si infrared-reflective ground plane designed to confine infrared radiation in an active electronic direct-conversion device. The interplay of strong infrared photon-phonon coupling and electromagnetic confinement in nanoscale devices is demonstrated to have a large impact on ultrafast electronic tunnelling in metal-oxide-semiconductor (MOS) structures. Infrared dispersion of SiO2 near a longitudinal optical (LO) phonon mode gives large transverse-field confinement in a nanometre-scale oxide-tunnel gap as the wavelength-dependent permittivity changes from 1 to 0, which leads to enhanced electromagnetic fields at material interfaces and a rectified displacement current that provides a direct conversion of infrared radiation into electric current. The spectral and electrical signatures of the nanoantenna-coupled tunnel diodes are examined under broadband blackbody and quantum-cascade laser (QCL) illumination. In the region near the LO phonon resonance, we obtained a measured photoresponsivity of 2.7 mA W(-1) cm(-2) at -0.1 V.

  16. Rectification of aerial images using piecewise linear transformation

    International Nuclear Information System (INIS)

    Liew, L H; Lee, B Y; Wang, Y C; Cheah, W S

    2014-01-01

    Aerial images are widely used in various activities by providing visual records. This type of remotely sensed image is helpful in generating digital maps, managing ecology, monitoring crop growth and region surveying. Such images could provide insight into areas of interest that have lower altitude, particularly in regions where optical satellite imaging is prevented due to cloudiness. Aerial images captured using a non-metric cameras contain real details of the images as well as unexpected distortions. Distortions would affect the actual length, direction and shape of objects in the images. There are many sources that could cause distortions such as lens, earth curvature, topographic relief and the attitude of the aircraft that is used to carry the camera. These distortions occur differently, collectively and irregularly in the entire image. Image rectification is an essential image pre-processing step to eliminate or at least reduce the effect of distortions. In this paper, a non-parametric approach with piecewise linear transformation is investigated in rectifying distorted aerial images. The non-parametric approach requires a set of corresponding control points obtained from a reference image and a distorted image. The corresponding control points are then applied with piecewise linear transformation as geometric transformation. Piecewise linear transformation divides the image into regions by triangulation. Different linear transformations are employed separately to triangular regions instead of using a single transformation as the rectification model for the entire image. The result of rectification is evaluated using total root mean square error (RMSE). Experiments show that piecewise linear transformation could assist in improving the limitation of using global transformation to rectify images

  17. Effect of ultrafiltration process on physico-chemical, rheological, microstructure and thermal properties of syrups from male and female date palm saps.

    Science.gov (United States)

    Makhlouf-Gafsi, Ines; Baklouti, Samia; Mokni, Abir; Danthine, Sabine; Attia, Hamadi; Blecker, Christophe; Besbes, Souhail; Masmoudi, Manel

    2016-07-15

    This study investigates the effect of the ultrafiltration process on physicochemical, rheological, microstructure and thermal properties of syrups from male and female date palm sap. All the studied syrups switched from pseudoplastic rheological behaviour (n=0.783) to Newtonian behaviour (n∼1) from 10 to 50 °C respectively and present similar thermal profiles. Results revealed that the ultrafiltration process significantly affects the rheological behaviour of the male and female syrups. These differences on rheological properties are attributed to the variation of chemical composition between sap and sap permeate syrups. Furthermore, the effect of temperature on viscosity of the syrups was investigated during heating and cooling processes at the same shear rate (50s(-1)). This study provides idea of the stability of the syrup by evaluating the area between heating and cooling curves. Actually, the syrup prepared from male sap permeate is the most stable between the four studied syrups. Copyright © 2016 Elsevier Ltd. All rights reserved.

  18. Influence of the mechanical sample treatment on the thermally stimulated exoelectron emission in aspect of the application for sample dating

    International Nuclear Information System (INIS)

    Zastawny, Andrzej; Bialon, Jan

    1999-01-01

    The examination was focused on a typical, contemporary produced ceramics, irradiated by the beta particles 90 Sr- 90 Y source. According to measurements, the mechanical treatment of the sample in the form of abrading and washing in alcohol did not affect the glow curve of the TSEE above the temperature 130 deg. C. Because the peaks of the TSEE, which can be taken full advantage for the dating must lie above 300 deg. C, the mechanical and washing preparing of the samples should not affect the measurements

  19. Testing accelerometer rectification error caused by multidimensional composite inputs with double turntable centrifuge.

    Science.gov (United States)

    Guan, W; Meng, X F; Dong, X M

    2014-12-01

    Rectification error is a critical characteristic of inertial accelerometers. Accelerometers working in operational situations are stimulated by composite inputs, including constant acceleration and vibration, from multiple directions. However, traditional methods for evaluating rectification error only use one-dimensional vibration. In this paper, a double turntable centrifuge (DTC) was utilized to produce the constant acceleration and vibration simultaneously and we tested the rectification error due to the composite accelerations. At first, we deduced the expression of the rectification error with the output of the DTC and a static model of the single-axis pendulous accelerometer under test. Theoretical investigation and analysis were carried out in accordance with the rectification error model. Then a detailed experimental procedure and testing results were described. We measured the rectification error with various constant accelerations at different frequencies and amplitudes of the vibration. The experimental results showed the distinguished characteristics of the rectification error caused by the composite accelerations. The linear relation between the constant acceleration and the rectification error was proved. The experimental procedure and results presented in this context can be referenced for the investigation of the characteristics of accelerometer with multiple inputs.

  20. The research on rectification and amplification of the image in mobile large container inspection system

    International Nuclear Information System (INIS)

    Jin Hui; Cheng Jianping; Chen Zhiqiang; Zhang Li

    2001-01-01

    The author introduces a geometrical rectification algorithm of the image in mobile large container inspection system. The comparison and discussion of the image before and after the rectification have been given. Amplification algorithms of the images are discussed. With all the algorithms, the quality of the images has been improved

  1. A boron nitride nanotube peapod thermal rectifier

    International Nuclear Information System (INIS)

    Loh, G. C.; Baillargeat, D.

    2014-01-01

    The precise guidance of heat from one specific location to another is paramount in many industrial and commercial applications, including thermal management and thermoelectric generation. One of the cardinal requirements is a preferential conduction of thermal energy, also known as thermal rectification, in the materials. This study introduces a novel nanomaterial for rectifying heat—the boron nitride nanotube peapod thermal rectifier. Classical non-equilibrium molecular dynamics simulations are performed on this nanomaterial, and interestingly, the strength of the rectification phenomenon is dissimilar at different operating temperatures. This is due to the contingence of the thermal flux on the conductance at the localized region around the scatterer, which varies with temperature. The rectification performance of the peapod rectifier is inherently dependent on its asymmetry. Last but not least, the favourable rectifying direction in the nanomaterial is established.

  2. A boron nitride nanotube peapod thermal rectifier

    Energy Technology Data Exchange (ETDEWEB)

    Loh, G. C., E-mail: jgloh@mtu.edu [Department of Physics, Michigan Technological University, Houghton, Michigan 49931 (United States); Institute of High Performance Computing, 1 Fusionopolis Way, #16-16 Connexis, Singapore 138632 (Singapore); Baillargeat, D. [CNRS-International-NTU-Thales Research Alliance (CINTRA), 50 Nanyang Drive, Singapore 637553 (Singapore)

    2014-06-28

    The precise guidance of heat from one specific location to another is paramount in many industrial and commercial applications, including thermal management and thermoelectric generation. One of the cardinal requirements is a preferential conduction of thermal energy, also known as thermal rectification, in the materials. This study introduces a novel nanomaterial for rectifying heat—the boron nitride nanotube peapod thermal rectifier. Classical non-equilibrium molecular dynamics simulations are performed on this nanomaterial, and interestingly, the strength of the rectification phenomenon is dissimilar at different operating temperatures. This is due to the contingence of the thermal flux on the conductance at the localized region around the scatterer, which varies with temperature. The rectification performance of the peapod rectifier is inherently dependent on its asymmetry. Last but not least, the favourable rectifying direction in the nanomaterial is established.

  3. Dating Violence

    Science.gov (United States)

    ... for Teens / Dating Violence Bulletins for Teens: Dating Violence What is it? If you are a victim ... often. If You Are a Victim of Dating Violence, You Might… Think it's your fault. Feel angry, ...

  4. Second Quaternary dating workshop

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-11-01

    The second Quaternary dating methods workshop was held at Lucas Heights and sponsored by ANSTO and AINSE. Topics covered include, isotope and thermoluminescence dating, usage of accelerator and thermal ionisation mass spectrometry in environmental studies emphasizing on the methodologies used and sample preparation

  5. Second Quaternary dating workshop

    International Nuclear Information System (INIS)

    1999-01-01

    The second Quaternary dating methods workshop was held at Lucas Heights and sponsored by ANSTO and AINSE. Topics covered include, isotope and thermoluminescence dating, usage of accelerator and thermal ionisation mass spectrometry in environmental studies emphasizing on the methodologies used and sample preparation

  6. Length dependence of rectification in organic co-oligomer spin rectifiers

    International Nuclear Information System (INIS)

    Hu Gui-Chao; Zhang Zhao; Li Ying; Ren Jun-Feng; Wang Chuan-Kui

    2016-01-01

    The rectification ratio of organic magnetic co-oligomer diodes is investigated theoretically by changing the molecular length. The results reveal two distinct length dependences of the rectification ratio: for a short molecular diode, the charge-current rectification changes little with the increase of molecular length, while the spin-current rectification is weakened sharply by the length; for a long molecular diode, both the charge-current and spin-current rectification ratios increase quickly with the length. The two kinds of dependence switch at a specific length accompanied with an inversion of the rectifying direction. The molecular ortibals and spin-resolved transmission analysis indicate that the dominant mechanism of rectification suffers a change at this specific length, that is, from asymmetric shift of molecular eigenlevels to asymmetric spatial localization of wave functions upon the reversal of bias. This work demonstrates a feasible way to control the rectification in organic co-oligomer spin diodes by adjusting the molecular length. (paper)

  7. Hybrid van der Waals SnO/MoS2 Heterojunctions for Thermal and Optical Sensing Applications

    KAUST Repository

    Wang, Zhenwei; He, Xin; Zhang, Xixiang; Alshareef, Husam N.

    2017-01-01

    /oxide hybrid vdWH based on n-type molybdenum disulfide (MoS2) and p-type tin monoxide (SnO) is presented, with promising rectification, thermal-sensing, and photosensing performance. Specifically, the hybrid SnO/MoS2 vdWH shows static rectification ratio of 2

  8. Large-Signal DG-MOSFET Modelling for RFID Rectification

    Directory of Open Access Journals (Sweden)

    R. Rodríguez

    2016-01-01

    Full Text Available This paper analyses the undoped DG-MOSFETs capability for the operation of rectifiers for RFIDs and Wireless Power Transmission (WPT at microwave frequencies. For this purpose, a large-signal compact model has been developed and implemented in Verilog-A. The model has been numerically validated with a device simulator (Sentaurus. It is found that the number of stages to achieve the optimal rectifier performance is inferior to that required with conventional MOSFETs. In addition, the DC output voltage could be incremented with the use of appropriate mid-gap metals for the gate, as TiN. Minor impact of short channel effects (SCEs on rectification is also pointed out.

  9. Ion current rectification, limiting and overlimiting conductances in nanopores.

    Directory of Open Access Journals (Sweden)

    Liesbeth van Oeffelen

    Full Text Available Previous reports on Poisson-Nernst-Planck (PNP simulations of solid-state nanopores have focused on steady state behaviour under simplified boundary conditions. These are Neumann boundary conditions for the voltage at the pore walls, and in some cases also Donnan equilibrium boundary conditions for concentrations and voltages at both entrances of the nanopore. In this paper, we report time-dependent and steady state PNP simulations under less restrictive boundary conditions, including Neumann boundary conditions applied throughout the membrane relatively far away from the nanopore. We simulated ion currents through cylindrical and conical nanopores with several surface charge configurations, studying the spatial and temporal dependence of the currents contributed by each ion species. This revealed that, due to slow co-diffusion of oppositely charged ions, steady state is generally not reached in simulations or in practice. Furthermore, it is shown that ion concentration polarization is responsible for the observed limiting conductances and ion current rectification in nanopores with asymmetric surface charges or shapes. Hence, after more than a decade of collective research attempting to understand the nature of ion current rectification in solid-state nanopores, a relatively intuitive model is retrieved. Moreover, we measured and simulated current-voltage characteristics of rectifying silicon nitride nanopores presenting overlimiting conductances. The similarity between measurement and simulation shows that overlimiting conductances can result from the increased conductance of the electric double-layer at the membrane surface at the depletion side due to voltage-induced polarization charges. The MATLAB source code of the simulation software is available via the website http://micr.vub.ac.be.

  10. 226Ra measurement by thermal ionisation mass spectrometry: Use of 226Ra and 14C for groundwater dating

    International Nuclear Information System (INIS)

    Dever, L.

    1997-01-01

    Recent developments in thermal ionisation mass spectrometry (TIMS) and in chemical separation Ra and Ba allow to analyse 226 Ra on smaller water samples ( 3 litres). The sampling has been realised on the Chalk aquifer of the Paris basin. The water samples have been collected in the unsaturated zone using in situ filtering devices and in the unconfined and confined parts of the aquifer in the boreholes used for public water supply. 226 Ra contents vary from 0.064±0.02 dpm/kg (n=6) in the unsaturated zone to 0.119±0.069 dpm/kg (n=7) in the unconfined aquifer and 0.319±0.057 dpm/kg (n=9) in the confined aquifer. For all the samples the 226 Ra/ 238 U activity ratios are much lower than the secular equilibrium. This points out that the two isotopes have different input function in the water during the mineralisation of the solution. The good correlation (r 2 =0.9) between the 226 Ra and Sr indicates that dissolution of Chalk is the dominant mechanism of mineralisation in 226 Ra of the solution. In the Chalk the mineralisation of the water occurs in the first metres of the unsaturated zone, during the water percolation the water rock interaction takes place through dissolution and precipitation of calcite in a non steady state. According to his distribution coefficient Sr is then a better tracer of dissolution/precipitation process than Ba. Using a geochemical model based on 226 Ra/Sr and Sr/Ca ratios an 'age' of the water could be determined. With 226 Ra half life of 1620 years we obtain 'ages' varying from 150 years to 1950 years in the unconfined aquifer. For the confined part of the aquifer where the redox condition is different it is necessary to use a geochemical model based on the U concentration in the water, the 226 Ra gives in such case ages varying from 1.8ka to 12.8ka. The radiocarbon ages obtained through usual chemical and/or isotopic models are quite similar and an isochrome between 226 Ra and 14 C ages can be calculated between 0 and 8ka

  11. Polaron effects on nonlinear optical rectification in asymmetrical Gaussian potential quantum wells with applied electric fields

    International Nuclear Information System (INIS)

    Wu, Jinghe; Guo, Kangxian; Liu, Guanghui

    2014-01-01

    Polaron effects on nonlinear optical rectification in asymmetrical Gaussian potential quantum wells are studied by the effective mass approximation and the perturbation theory. The numerical results show that nonlinear optical rectification coefficients are strongly dependent on the barrier hight V 0 of the Gaussian potential quantum wells, the range L of the confinement potential and the electric field F. Besides, the numerical results show that no matter how V 0 , L and F change, taking into consideration polaron effects, the optical rectification coefficients χ 0 (2) get greatly enhanced.

  12. Temperature-gated thermal rectifier for active heat flow control.

    Science.gov (United States)

    Zhu, Jia; Hippalgaonkar, Kedar; Shen, Sheng; Wang, Kevin; Abate, Yohannes; Lee, Sangwook; Wu, Junqiao; Yin, Xiaobo; Majumdar, Arun; Zhang, Xiang

    2014-08-13

    Active heat flow control is essential for broad applications of heating, cooling, and energy conversion. Like electronic devices developed for the control of electric power, it is very desirable to develop advanced all-thermal solid-state devices that actively control heat flow without consuming other forms of energy. Here we demonstrate temperature-gated thermal rectification using vanadium dioxide beams in which the environmental temperature actively modulates asymmetric heat flow. In this three terminal device, there are two switchable states, which can be regulated by global heating. In the "Rectifier" state, we observe up to 28% thermal rectification. In the "Resistor" state, the thermal rectification is significantly suppressed (Rectifier state. This temperature-gated rectifier can have substantial implications ranging from autonomous thermal management of heating and cooling systems to efficient thermal energy conversion and storage.

  13. Measurement and understanding of single-molecule break junction rectification caused by asymmetric contacts

    International Nuclear Information System (INIS)

    Wang, Kun; Zhou, Jianfeng; Hamill, Joseph M.; Xu, Bingqian

    2014-01-01

    The contact effects of single-molecule break junctions on rectification behaviors were experimentally explored by a systematic control of anchoring groups of 1,4-disubstituted benzene molecular junctions. Single-molecule conductance and I-V characteristic measurements reveal a strong correlation between rectifying effects and the asymmetry in contacts. Analysis using energy band models and I-V calculations suggested that the rectification behavior is mainly caused by asymmetric coupling strengths at the two contact interfaces. Fitting of the rectification ratio by a modified Simmons model we developed suggests asymmetry in potential drop across the asymmetric anchoring groups as the mechanism of rectifying I-V behavior. This study provides direct experimental evidence and sheds light on the mechanisms of rectification behavior induced simply by contact asymmetry, which serves as an aid to interpret future single-molecule electronic behavior involved with asymmetric contact conformation

  14. Entropy production and rectification efficiency in colloid transport along a pulsating channel

    Science.gov (United States)

    Florencia Carusela, M.; Rubi, J. Miguel

    2018-06-01

    We study the current rectification of particles moving in a pulsating channel under the influence of an applied force. We have shown the existence of different rectification scenarios in which entropic and energetic effects compete. The effect can be quantified by means of a rectification coefficient that is analyzed in terms of the force, the frequency and the diffusion coefficient. The energetic cost of the motion of the particles expressed in terms of the entropy production depends on the importance of the entropic contribution to the total force. Rectification is more important at low values of the applied force when entropic effects become dominant. In this regime, the entropy production is not invariant under reversal of the applied force. The phenomenon observed could be used to optimize transport in microfluidic devices or in biological channels.

  15. Ratchet rectification effect on the translocation of a flexible polyelectrolyte chain

    Energy Technology Data Exchange (ETDEWEB)

    Mondal, Debasish; Muthukumar, M., E-mail: muthu@polysci.umass.edu [Department of Polymer Science and Engineering, University of Massachusetts, Amherst, Massachusetts 01003 (United States)

    2016-08-28

    We report a three dimensional Langevin dynamics simulation of a uniformly charged flexible polyelectrolyte chain, translocating through an asymmetric narrow channel with periodically varying cross sections under the influence of a periodic external electric field. When reflection symmetry of the channel is broken, a rectification effect is observed with a favored direction for the chain translocation. For a given volume of the channel unit and polymer length, the rectification occurs below a threshold frequency of the external periodic driving force. We have also observed that the extent of the rectification varies non-monotonically with increasing molecular weight and the strength of geometric asymmetry of the channel. Observed non-monotonicity of the rectification performance has been interpreted in terms of a competition between two effects arising from the channel asymmetry and change in conformational entropy. An analytical model is presented with predictions consistent with the simulation results.

  16. The role of geometry in nanoscale rectennas for rectification and energy conversion

    Science.gov (United States)

    Miskovsky, N. M.; Cutler, P. H.; Mayer, A.; Willis, B. G.; Zimmerman, D. T.; Weisel, G. J.; Chen, James M.; Sullivan, T. E.; Lerner, P. B.

    2013-09-01

    We have previously presented a method for optical rectification that has been demonstrated both theoretically and experimentally and can be used for the development of a practical rectification and energy conversion device for the electromagnetic spectrum including the visible portion. This technique for optical frequency rectification is based, not on conventional material or temperature asymmetry as used in MIM or Schottky diodes, but on a purely geometric property of the antenna tip or other sharp edges that may be incorporated on patch antennas. This "tip" or edge in conjunction with a collector anode providing connection to the external circuit constitutes a tunnel junction. Because such devices act as both the absorber of the incident radiation and the rectifier, they are referred to as "rectennas." Using current nanofabrication techniques and the selective Atomic Layer Deposition (ALD) process, junctions of 1 nm can be fabricated, which allow for rectification of frequencies up to the blue portion of the spectrum (see Section 2).

  17. Dating Violence

    Science.gov (United States)

    Stader, David L.

    2011-01-01

    Dating violence is a form of student-on-student victimization and is a serious school safety issue. Research indicates that at a minimum, 10 percent of high school students are victims of dating violence in one form or another. Among female high school students that date, some data indicate that as many as 30 percent may be victims of dating…

  18. Removal of spurious normal polarity directions in the Kanapoi Formation with progressive thermal demagnetization: implications for dating Pliocene hominin fossils from the Turkana Basin of Kenya

    Science.gov (United States)

    Lepre, C. J.; Kent, D.

    2017-12-01

    The Kanapoi Formation is a 75-m-thick sedimentary unit in northern Kenya whose fossil record documents the evolution of the genus Australopithecus and habitual bipedalism in Pliocene hominins. Published 40Ar/39Ar dates of 4.20 to 4.10 Ma for three aqueously reworked tuffs from the lower and middle stratigraphic intervals of the formation and a whole-rock K-Ar date of 3.4 ± 0.1 Ma on the Kalokwanya Basalt, which caps the succession, coupled with paleomagnetic data from an unpublished thesis have been used to constrain the age of the unit (McDougall+2012 J Geol Soc). Normal polarities at the base of the formation were correlated to normal subchron C3n.1n (Cochiti Subchron) and would extend the Kanapoi chronostratigraphy back to between 4.29 and 4.18 Ma. The credibility of the normal polarities at the base and elsewhere in the formation as records of the geomagnetic field at the time of deposition, however, is called into question by the ubiquity of the high-coercivity mineral hematite in the Kanapoi sediments and the alternating field demagnetization methods exclusively used to generate the polarity directions. We tested this proposed chronostratigraphy of the Kanapoi Fm by collecting nearly 70 independently orientated block samples from 10 outcrop localities, which sampled roughly two-thirds of the total stratigraphic thickness of the formation and covered the entire vertical extent of the supposed basal normal polarity magnetozone. For most every specimen, stepwise thermal demagnetization (TD) resolved well-defined characteristic magnetizations of uniformly reverse polarity and were carried by a high-temperature component consistent with hematite. TD of the Kalokwanya Basalt confirmed its reverse magnetic polarity, which implies emplacement most likely prior to the base of normal Chron C2An (Gauss Chron) at 3.58 Ma. Kanapoi sediments thus accumulated sometime during reverse subchron C2Ar (4.18-3.58 Ma) but over a period of much less than 600 kyr. Basal age control

  19. Luminescence dating

    International Nuclear Information System (INIS)

    Rieser, U.

    2009-01-01

    The luminescence techniques have evolved over the last 40 years to a powerful dating instrument in archaeology and geoscience. Depending on how the luminescence is stimulated, one distinguishes the phenomena of thermoluminescence (TL), optically stimulated luminescence (OSL) and infrared stimulated luminescence (IRSL). Each of these phenomena has its specific potential for dating various archaeological materals in the time range from medieval back to palaeolithic periods, or, speaking in geological terms, for dating of Holocene and late Pleistocene objects. The OSL and IRSL techniques are sometimes treated together as 'optical dating'. The luminescence techniques differ from other major dating techniques, such as 14 C, essentially by their applicability to inorganic materials, their wide age-range from about 100 years to more than 100,000 years and the kind of datable events which are the last exposure to heat or to light. (author). 10 refs., 3 figs.

  20. Luminescence dating

    International Nuclear Information System (INIS)

    Rieser, U.

    2008-01-01

    The luminescence techniques have evolved over the last 40 years to a powerful dating instrument in archaeology and geoscience. Depending on how the luminescence is stimulated, one distinguishes the phenomena of thermoluminescence (TL), optically stimulated luminescence (OSL) and infrared stimulated luminescence (IRSL). Each of these phenomena has its specific potential for dating various archaeological materals in the time range from medieval back to palaeolithic periods, or, speaking in geological terms, for dating of Holocene and late Pleistocene objects. The OSL and IRSL techniques are sometimes treated together as 'optical dating'. The luminescence techniques differ from other major dating techniques, such as 14 C, essentially by their applicability to inorganic materials, their wide age-range from about 100 years to more than 100,000 years and the kind of datable events which are the last exposure to heat or to light. (author). 10 refs., 3 figs

  1. Luminescence dating

    International Nuclear Information System (INIS)

    Rieser, U.

    2012-01-01

    The luminescence techniques have evolved over the last 40 years to a powerful dating instrument in archaeology and geoscience. Depending on how the luminescence is stimulated, one distinguishes the phenomena of thermoluminescence (TL), optically stimulated luminescence (OSL) and infrared stimulated luminescence (IRSL). Each of these phenomena has its specific potential for dating various archaeological materials in the time range from medieval back to palaeolithic periods, or, speaking in geological terms, for dating of Holocene and late Pleistocene objects. The OSL and IRSL techniques are sometimes treated together as 'optical dating'. The luminescence techniques differ from other major dating techniques, such as 14 C, essentially by their applicability to inorganic materials, their wide age-range from about 100 years to more than 100,000 years and the kind of datable events which are the last exposure to heat or to light. (author). 10 refs., 3 figs.

  2. Luminescence dating

    International Nuclear Information System (INIS)

    Rieser, U.

    2009-01-01

    The luminescence techniques have evolved over the last 40 years to a powerful dating instrument in archaeology and geoscience. Depending on how the luminescence is stimulated, one distinguishes the phenomena of thermoluminescence (TL), optically stimulated luminescence (OSL) and infrared stimulated luminescence (IRSL). Each of these phenomena has its specific potential for dating various archaeological materals in the time range from medieval back to palaeolithic periods, or, speaking in geological terms, for dating of Holocene and late Pleistocene objects. The OSL and IRSL techniques are sometimes treated together as 'optical dating'. The luminescence techniques differ from other major dating techniques, such as 14 C, essentially by their applicability to inorganic materials, their wide age-range from about 100 years to more than 100,000 years and the kind of datable events which are the last exposure to heat or to light. (author). 10 refs., 3 figs

  3. Luminescence dating

    International Nuclear Information System (INIS)

    Rieser, U.

    2013-01-01

    The luminescence techniques have evolved over the last 40 years to a powerful dating instrument in archaeology and geoscience. Depending on how the luminescence is stimulated, one distinguishes the phenomena of thermoluminescence (TL), optically stimulated luminescence (OSL) and infrared stimulated luminescence (IRSL). Each of these phenomena has its specific potential for dating various archaeological materials in the time range from medieval back to palaeolithic periods, or, speaking in geological terms, for dating of Holocene and late Pleistocene objects. The OSL and IRSL techniques are sometimes treated together as 'optical dating'. The luminescence techniques differ from other major dating techniques, such as 14 C, essentially by their applicability to inorganic materials, their wide age-range from about 100 years to more than 100,000 years and the kind of datable events which are the last exposure to heat or to light. (author). 10 refs., 3 figs.

  4. Wireless power transfer exploring spin rectification and inverse spin Hall effects

    Science.gov (United States)

    Seeger, R. L.; Garcia, W. J. S.; Dugato, D. A.; da Silva, R. B.; Harres, A.

    2018-04-01

    Devices based on spin rectification effects are of great interest for broadband communication applications, since they allow the rectification of radio frequency signals by simple ferromagnetic materials. The phenomenon is enhanced at ferromagnetic resonance condition, which may be attained when an external magnetic field is applied. The necessity of such field, however, hinders technological applications. Exploring spin rectification and spin Hall effects in exchange-biased samples, we were able to rectify radio frequency signals without an external applied magnetic field. Direct voltages of the order of μV were obtained when Ta/NiFe/FeMn/Ta thin films were exposed to microwaves in a shorted microstrip line for a relatively broad frequency range. Connecting the films to a resistive load, we estimated the fraction of the incident radio frequency power converted into usable dc power.

  5. Maximizing ion current rectification in a bipolar conical nanopore fluidic diode using optimum junction location.

    Science.gov (United States)

    Singh, Kunwar Pal

    2016-10-12

    The ion current rectification has been obtained as a function of the location of a heterojunction in a bipolar conical nanopore fluidic diode for different parameters to determine the junction location for maximum ion current rectification using numerical simulations. Forward current peaks for a specific location of the junction and reverse current decreases with the junction location due to a change in ion enrichment/depletion in the pore. The optimum location of the heterojunction shifts towards the tip with base/tip diameter and surface charge density, and towards the base with the electrolyte concentration. The optimum location of the heterojunction has been approximated by an equation as a function of pore length, base/tip diameter, surface charge density and electrolyte concentration. The study is useful to design a rectifier with maximum ion current rectification for practical purposes.

  6. Current rectification in a single molecule diode: the role of electrode coupling.

    Science.gov (United States)

    Sherif, Siya; Rubio-Bollinger, Gabino; Pinilla-Cienfuegos, Elena; Coronado, Eugenio; Cuevas, Juan Carlos; Agraït, Nicolás

    2015-07-24

    We demonstrate large rectification ratios (> 100) in single-molecule junctions based on a metal-oxide cluster (polyoxometalate), using a scanning tunneling microscope (STM) both at ambient conditions and at low temperature. These rectification ratios are the largest ever observed in a single-molecule junction, and in addition these junctions sustain current densities larger than 10(5) A cm(-2). By following the variation of the I-V characteristics with tip-molecule separation we demonstrate unambiguously that rectification is due to asymmetric coupling to the electrodes of a molecule with an asymmetric level structure. This mechanism can be implemented in other type of molecular junctions using both organic and inorganic molecules and provides a simple strategy for the rational design of molecular diodes.

  7. Research on geometric rectification of the Large FOV Linear Array Whiskbroom Image

    Science.gov (United States)

    Liu, Dia; Liu, Hui-tong; Dong, Hao; Liu, Xiao-bo

    2015-08-01

    To solve the geometric distortion problem of large FOV linear array whiskbroom image, a model of multi center central projection collinearity equation was founded considering its whiskbroom and linear CCD imaging feature, and the principle of distortion was analyzed. Based on the rectification method with POS, we introduced the angular position sensor data of the servo system, and restored the geometric imaging process exactly. An indirect rectification scheme aiming at linear array imaging with best scanline searching method was adopted, matrixes for calculating the exterior orientation elements was redesigned. We improved two iterative algorithms for this device, and did comparison and analysis. The rectification for the images of airborne imaging experiment showed ideal effect.

  8. Effects of contrast improvement on high voltage rectification type of x-ray diagnostic apparatus

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Hoo Min; Yoon, Joon [Dept. of Radiological technology, Dongnam Health University, Suwon (Korea, Republic of); Kim, Hyun Ju [Dept. of Radiology, Soonchunhyang University Hospital Buchen, Bucheon (Korea, Republic of)

    2014-09-15

    The purpose of this study was to analyze the effect on the selectivity on of high-voltage rectification device that measured the performance of the grid, and the contrast improvement ability (K factor) by measuring the scattered radiation content of the transmitted X-rays. The scattered radiation generated when the X-ray flux comes from the diagnostic X-ray generator that passes through an object. Targeting four different rectifications of X-ray generators, the mean value of the tube voltage and the tube current was measured in order to maximize the accuracy of the generating power dose within the same exposure condition. Using fluorescence meter, the content of the scattered rays that are transmitted through the acrylic was measured depending on the grid usage. When grid is not used, the content of the scattered rays was the lowest (34.158%) with the single-phase rectifier, was increased with the inverter rectifier (37.043%) and the three-phase 24-peak rectification method (37.447%). The difference of the scattered radiation content of each device was significant from the lowest 0.404% to the highest 3.289% while using 8:1 grid, the content of the scattered ray was the lowest with the single content of the scattered ray was the lowest with the single-phase rectifier (18.258%), was increased with the rectifier (25.502%) and the 24-peaks rectification (24.217%). Furthermore, there was difference up to content 7.244% to the lowest content 1.285% within three-phase 24-peaks rectification, inverter rectifications, and single-phase rectifier depending on the selectivity of the grid. Drawn from the statistical analysis, there was a similar relationship between the contrast improvement factor and the K factor. As a result, the grid selectivity and the contrast were increased within the single-phase rectifier rather than the constant voltage rectifier.

  9. Effects of contrast improvement on high voltage rectification type of x-ray diagnostic apparatus

    International Nuclear Information System (INIS)

    Lee, Hoo Min; Yoon, Joon; Kim, Hyun Ju

    2014-01-01

    The purpose of this study was to analyze the effect on the selectivity on of high-voltage rectification device that measured the performance of the grid, and the contrast improvement ability (K factor) by measuring the scattered radiation content of the transmitted X-rays. The scattered radiation generated when the X-ray flux comes from the diagnostic X-ray generator that passes through an object. Targeting four different rectifications of X-ray generators, the mean value of the tube voltage and the tube current was measured in order to maximize the accuracy of the generating power dose within the same exposure condition. Using fluorescence meter, the content of the scattered rays that are transmitted through the acrylic was measured depending on the grid usage. When grid is not used, the content of the scattered rays was the lowest (34.158%) with the single-phase rectifier, was increased with the inverter rectifier (37.043%) and the three-phase 24-peak rectification method (37.447%). The difference of the scattered radiation content of each device was significant from the lowest 0.404% to the highest 3.289% while using 8:1 grid, the content of the scattered ray was the lowest with the single content of the scattered ray was the lowest with the single-phase rectifier (18.258%), was increased with the rectifier (25.502%) and the 24-peaks rectification (24.217%). Furthermore, there was difference up to content 7.244% to the lowest content 1.285% within three-phase 24-peaks rectification, inverter rectifications, and single-phase rectifier depending on the selectivity of the grid. Drawn from the statistical analysis, there was a similar relationship between the contrast improvement factor and the K factor. As a result, the grid selectivity and the contrast were increased within the single-phase rectifier rather than the constant voltage rectifier

  10. Rectification cleaning AsCl3 from the admixture of oxygen

    Directory of Open Access Journals (Sweden)

    Maznitska O. V.

    2008-06-01

    Full Text Available The process of the rectification cleaning of three-chlorous arsenic from the admixtures of products of his hydrolysis in the atmosphere of chlorous hydrogen has been considered in the article. Dependence of coefficient of relative volatility a three-chlorous arsenic from his concentration in muriatic solution is explored. The conduct of coefficient of relative volatility with concentrations of HCl and AsCl3 is compared. Saving of equalization of balance and equalization of working curve of column at such conduct of process of rectification is shown.

  11. Calculating lattice thermal conductivity: a synopsis

    Science.gov (United States)

    Fugallo, Giorgia; Colombo, Luciano

    2018-04-01

    We provide a tutorial introduction to the modern theoretical and computational schemes available to calculate the lattice thermal conductivity in a crystalline dielectric material. While some important topics in thermal transport will not be covered (including thermal boundary resistance, electronic thermal conduction, and thermal rectification), we aim at: (i) framing the calculation of thermal conductivity within the general non-equilibrium thermodynamics theory of transport coefficients, (ii) presenting the microscopic theory of thermal conduction based on the phonon picture and the Boltzmann transport equation, and (iii) outlining the molecular dynamics schemes to calculate heat transport. A comparative and critical addressing of the merits and drawbacks of each approach will be discussed as well.

  12. Radiometric dating

    International Nuclear Information System (INIS)

    Das, N.R.

    2017-01-01

    Since the discovery of natural radioactivity in uranium, in the last decade of the nineteenth century, the nuclear property of radioactive decay of radionuclides at immutable rates has been effectively utilized in dating of varieties of naturally occurring geological matrices and the organisms which constantly replenish their "1"4C supply through respiration when alive on earth. During the period, applications of radiometric dating techniques have been extensively diversified and have enabled the geologists to indicate the absolute time scales of geological formations and the evolution of the solar system, the earth, meteorites, lunar rocks, etc. and the archaeologists to record the facts of history of several important events like dinosaur era, Iceman, the Shroud in Turin and many other ancient artefacts. In the development of dating methods, varieties of naturally occurring radio-isotopic systems with favorable half-lives ranging from about 10 years to over 100 billion years have been used as radiometric clocks. (author)

  13. Geometrical control of ionic current rectification in a configurable nanofluidic diode.

    Science.gov (United States)

    Alibakhshi, Mohammad Amin; Liu, Binqi; Xu, Zhiping; Duan, Chuanhua

    2016-09-01

    Control of ionic current in a nanofluidic system and development of the elements analogous to electrical circuits have been the subject of theoretical and experimental investigations over the past decade. Here, we theoretically and experimentally explore a new technique for rectification of ionic current using asymmetric 2D nanochannels. These nanochannels have a rectangular cross section and a stepped structure consisting of a shallow and a deep side. Control of height and length of each side enables us to obtain optimum rectification at each ionic strength. A 1D model based on the Poisson-Nernst-Planck equation is derived and validated against the full 2D numerical solution, and a nondimensional concentration is presented as a function of nanochannel dimensions, surface charge, and the electrolyte concentration that summarizes the rectification behavior of such geometries. The rectification factor reaches a maximum at certain electrolyte concentration predicted by this nondimensional number and decays away from it. This method of fabrication and control of a nanofluidic diode does not require modification of the surface charge and facilitates the integration with lab-on-a-chip fluidic circuits. Experimental results obtained from the stepped nanochannels are in good agreement with the 1D theoretical model.

  14. Rectification of graphene self-switching diodes: First-principles study

    Science.gov (United States)

    Ghaziasadi, Hassan; Jamasb, Shahriar; Nayebi, Payman; Fouladian, Majid

    2018-05-01

    The first principles calculations based on self-consistent charge density functional tight-binding have performed to investigate the electrical properties and rectification behavior of the graphene self-switching diodes (GSSD). The devices contained two structures called CG-GSSD and DG-GSSD which have metallic or semiconductor gates depending on their side gates have a single or double hydrogen edge functionalized. We have relaxed the devices and calculated I-V curves, transmission spectrums and maximum rectification ratios. We found that the DG-MSM devices are more favorable and more stable. Also, the DG-MSM devices have better maximum rectification ratios and current. Moreover, by changing the side gates widths and behaviors from semiconductor to metal, the threshold voltages under forward bias changed from +1.2 V to +0.3 V. Also, the maximum currents are obtained from 1.12 μA to 10.50 μA. Finally, the MSM and SSS type of all devices have minimum and maximum values of voltage threshold and maximum rectification ratios, but the 769-DG devices don't obey this rule.

  15. High rectification ratios of Fe-porphyrin molecules on Au facets

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Xiaoyu; Wang, Gwo-Ching [Department of Physics, Applied Physics and Astronomy, Rensselaer Polytechnic Institute, 110, 8th Street, Troy, NY 12180 (United States); Lewis, Kim M., E-mail: lewisk2@rpi.edu [Department of Physics, Applied Physics and Astronomy, Rensselaer Polytechnic Institute, 110, 8th Street, Troy, NY 12180 (United States)

    2012-09-14

    We report room temperature measurements of current vs. voltage (I-V) from self-assembled Fe porphyrin [Fe(III) 5,15-di[4-(s-acetylthio)phenyl]-10,20-diphenyl porphine] molecular layers formed on annealed gold crystal facets on glass substrates. I-V curves were measured using an atomic force microscope with a conductive platinum tip. We observed a rectifier effect that shows asymmetric I-V curves from a monolayer of molecules. The majority rectification ratios at {+-}1 V obtained from hundreds of I-V lie in between 20 and 200, with the highest up to 9000. This is in contrast to the symmetric I-V curves measured from a few nm thick multilayer molecular islands. We contribute the observed rectification in ultrathin FeP molecular layers from asymmetric Schottky barriers that result from molecules in different bonding strengths to electrodes of gold and platinum. -- Highlights: Black-Right-Pointing-Pointer FeP molecular layers or islands of different thickness were self-assembled on Au. Black-Right-Pointing-Pointer High rectification ratios up to 9000 observed in sub-nm thick FeP molecular layers. Black-Right-Pointing-Pointer Measured current vs. voltage using a conductive AFM tip as one electrode. Black-Right-Pointing-Pointer Observed rectification of symmetric molecules using two different electrodes.

  16. Giant rectification in graphene nanoflake molecular devices with asymmetric graphene nanoribbon electrodes

    International Nuclear Information System (INIS)

    Ji, Xiao-Li; Xie, Zhen; Zuo, Xi; Zhang, Guang-Ping; Li, Zong-Liang; Wang, Chuan-Kui

    2016-01-01

    By applying density functional theory based nonequilibrium Green's function method, we theoretically investigate the electron transport properties of a zigzag-edged trigonal graphene nanoflake (ZTGNF) sandwiched between two asymmetric zigzag graphene nanoribbon (zGNR) and armchair graphene nanoribbon (aGNR) electrodes with carbon atomic chains (CACs) as the anchoring groups. Significant rectifying effects have been observed for these molecular devices in low bias voltage regions. Interestingly, the rectifying performance of molecular devices can be optimized by changing the width of the aGNR electrode and the number of anchoring CACs. Especially, the molecular device displays giant rectification ratios up to the order of 10"4 when two CACs are used as the anchoring group between the ZTGNF and the right aGNR electrode. Further analysis indicates that the asymmetric shift of the perturbed molecular energy levels and the spatial parity of the electron wavefunctions in the electrodes around the Fermi level play key roles in determining the rectification performance. And the spatial distributions of tunneling electron wavefunctions under negative bias voltages can be modified to be very localized by changing the number of anchoring CACs, which is found to be the origin of the giant rectification ratios. - Highlights: • The rectification properties of triangular Graphene nanoflakes are investigated. • The rectifying performance can be optimized by changing the width of the right arm-chaired GNR electrode. • The rectifying performance can also be tuned by varying the number of anchoring carbon atomic chains.

  17. Radiocarbon dating

    International Nuclear Information System (INIS)

    Lazos R, L.

    2005-01-01

    The application of the radiocarbon dating in archaeology has not served only to solve problems related with the establishment of chronologies, but also in the development of archaeological methods of excavation and interpretation. This has been possible because the dating method by radiocarbon provides a common temporary scale that transcends the cultural and regional frontiers. It is even spoken of the revolution that has meant the fact that the application of this method has allowed to the archaeologist to pass from the construction of chronologies until the evaluation and dynamic interpretation of the archaeological data to build theories. This work explains and compares methods for the detection of 14 C, as the gas counting, the liquid scintillation counting and the mass spectrometry with accelerators. (Author)

  18. Thermoluminescence dating

    International Nuclear Information System (INIS)

    Price, D.M.

    1999-01-01

    Thermoluminescence (TL) dating of sediments depends upon the acquisition and long term stable storage of TL energy by crystalline minerals contained within a sedimentary unit. This energy is stored in the form of trapped electrons and quartz sand is the most commonly used mineral employed in the dating process. Prior to the final depositional episode it is necessary that any previously acquired TL is removed by exposure to sunlight. After burial the TL begins to build up again at a rate dependent upon the radiation flux delivered by long-lived isotopes of uranium, thorium and potassium. The presence of rubidium and cosmic radiation generally play a lesser but contributory roll, and the total radiation dose delivered to the TL phosphor is modified by the presence of water. The period since deposition is therefore measured by determining the total amount of stored TL energy, the palaeodose (P), and the rate at which this energy is acquired, the annual radiation dose (ARD). TL dating may be applied to eolian, fluvial, coastal and in some cases, marine sediments. the technique is also successfully applied to volcanic materials and to a certain extent to archeological specimens

  19. Phase-change radiative thermal diode

    OpenAIRE

    Ben-Abdallah, Philippe; Biehs, Svend-Age

    2013-01-01

    A thermal diode transports heat mainly in one preferential direction rather than in the opposite direction. This behavior is generally due to the non-linear dependence of certain physical properties with respect to the temperature. Here we introduce a radiative thermal diode which rectifies heat transport thanks to the phase transitions of materials. Rectification coefficients greater than 70% and up to 90% are shown, even for small temperature differences. This result could have important ap...

  20. Inelastic transport and low-bias rectification in a single-molecule diode.

    Science.gov (United States)

    Hihath, Joshua; Bruot, Christopher; Nakamura, Hisao; Asai, Yoshihiro; Díez-Pérez, Ismael; Lee, Youngu; Yu, Luping; Tao, Nongjian

    2011-10-25

    Designing, controlling, and understanding rectification behavior in molecular-scale devices has been a goal of the molecular electronics community for many years. Here we study the transport behavior of a single molecule diode, and its nonrectifying, symmetric counterpart at low temperatures, and at both low and high biases to help elucidate the electron-phonon interactions and transport mechanisms in the rectifying system. We find that the onset of current rectification occurs at low biases, indicating a significant change in the elastic transport pathway. However, the peaks in the inelastic electron tunneling (IET) spectrum are antisymmetric about zero bias and show no significant changes in energy or intensity in the forward or reverse bias directions, indicating that despite the change in the elastic transmission probability there is little impact on the inelastic pathway. These results agree with first principles calculations performed to evaluate the IETS, which also allow us to identify which modes are active in the single molecule junction.

  1. Rectification of pulsatile stress on soft tissues: a mechanism for normal-pressure hydrocephalus

    Science.gov (United States)

    Jalikop, Shreyas; Hilgenfeldt, Sascha

    2011-11-01

    Hydrocephalus is a pathological condition of the brain that occurs when cerebrospinal fluid (CSF) accumulates excessively in the brain cavities, resulting in compression of the brain parenchyma. Counter-intuitively, normal-pressure hydrocephalus (NPH) does not show elevated pressure differences across the compressed parenchyma. We investigate the effects of nonlinear tissue mechanics and periodic driving in this system. The latter is due to the cardiac cycle, which provides significant intracranial pressure and volume flow rate fluctuations. Nonlinear rectification of the periodic driving within a model of fluid flow in poroelastic material can lead to compression or expansion of the parenchyma, and this effect does not rely on changes in the mean intracranial pressure. The rectification effects can occur gradually over several days, in agreement with clinical studies of NPH.

  2. Rectification effect about vacuum separating carbon nanotube bundle predicted by first-principles study

    Energy Technology Data Exchange (ETDEWEB)

    Min, Y., E-mail: minshiyi@gmail.com [School of Science, Nantong University, Nantong, Jiangsu, 226007 (China); Fang, J.H.; Zhong, C.G. [School of Science, Nantong University, Nantong, Jiangsu, 226007 (China); Yao, K.L. [School of Physics, Huazhong University of Science and Technology, Wuhan, 430074 (China)

    2012-05-07

    For the molecular spintronics transport systems, we propose that the spin current rectifier can be constructed using the nonmagnetic lead. The proposal is confirmed according to the first-principles study of the transport characteristics of a vacuum separating (15,0) carbon nanotube bundle where only one zigzag edge is hydrogenated. The strong rectification effect for spin (charge) current is obtained in the case of the magnetic parallel (anti-parallel) configuration of two zigzag edges. Our investigations indicate that such device can be used as the spin filter and the counterpart of the p–n junction in the field of molecular electronics. -- Highlights: ► We propose that nonmagnetic leads can construct spin current rectifier. ► We propose a spin diode and a filter using CNT. ► The spin and charge current all have the rectification effect in the one-dimensional spin diode.

  3. Forward rectification: spatial image normalization for a video from a forward facing vehicle camera

    Science.gov (United States)

    Prun, Viktor; Polevoy, Dmitri; Postnikov, Vassiliy

    2017-03-01

    The work in this paper is focused around visual ADAS (Advanced Driver Assistance Systems). We introduce forward rectification - a technique for making computer vision algorithms more robust against camera mount point and mount angles. Using the technique can increase the quality of recognition as well as lower the dimensionality for algorithm invariance, making it possible to apply simpler affine-invariant algorithms for applications that require projective invariance. Providing useful results this rectification requires thorough calibration of the camera, which can be done automatically or semi-automatically. The technique is of general nature and can be applied to different algorithms, such as pattern matching detectors, convolutional neural networks. The applicability of the technique is demonstrated on HOG-based car detector detection rate.

  4. Electrically tunable tunneling rectification magnetoresistance in magnetic tunneling junctions with asymmetric barriers.

    Science.gov (United States)

    Wang, Jing; Huang, Qikun; Shi, Peng; Zhang, Kun; Tian, Yufeng; Yan, Shishen; Chen, Yanxue; Liu, Guolei; Kang, Shishou; Mei, Liangmo

    2017-10-26

    The development of multifunctional spintronic devices requires simultaneous control of multiple degrees of freedom of electrons, such as charge, spin and orbit, and especially a new physical functionality can be realized by combining two or more different physical mechanisms in one specific device. Here, we report the realization of novel tunneling rectification magnetoresistance (TRMR), where the charge-related rectification and spin-dependent tunneling magnetoresistance are integrated in Co/CoO-ZnO/Co magnetic tunneling junctions with asymmetric tunneling barriers. Moreover, by simultaneously applying direct current and alternating current to the devices, the TRMR has been remarkably tuned in the range from -300% to 2200% at low temperature. This proof-of-concept investigation provides an unexplored avenue towards electrical and magnetic control of charge and spin, which may apply to other heterojunctions to give rise to more fascinating emergent functionalities for future spintronics applications.

  5. Rectification of current responds to incorporation of fullerenes into mixed-monolayers of alkanethiolates in tunneling junctions.

    Science.gov (United States)

    Qiu, Li; Zhang, Yanxi; Krijger, Theodorus L; Qiu, Xinkai; Hof, Patrick Van't; Hummelen, Jan C; Chiechi, Ryan C

    2017-03-01

    This paper describes the rectification of current through molecular junctions comprising self-assembled monolayers of decanethiolate through the incorporation of C 60 fullerene moieties bearing undecanethiol groups in junctions using eutectic Ga-In (EGaIn) and Au conducting probe AFM (CP-AFM) top-contacts. The degree of rectification increases with increasing exposure of the decanethiolate monolayers to the fullerene moieties, going through a maximum after 24 h. We ascribe this observation to the resulting mixed-monolayer achieving an optimal packing density of fullerene cages sitting above the alkane monolayer. Thus, the degree of rectification is controlled by the amount of fullerene present in the mixed-monolayer. The voltage dependence of R varies with the composition of the top-contact and the force applied to the junction and the energy of the lowest unoccupied π-state determined from photoelectron spectroscopy is consistent with the direction of rectification. The maximum value of rectification R = | J (+)/ J (-)| = 940 at ±1 V or 617 at ±0.95 V is in agreement with previous studies on pure monolayers relating the degree of rectification to the volume of the head-group on which the frontier orbitals are localized.

  6. Hydrostatic pressure and temperature effects on nonlinear optical rectification in a lens shape InAs/GaAs quantum dot

    International Nuclear Information System (INIS)

    Bouzaïene, L.; Ben Mahrsia, R.; Baira, M.; Sfaxi, L.; Maaref, H.

    2013-01-01

    We have performed theoretical calculation of the nonlinear optical rectification in a lens shape InAs/GaAs quantum dot (0D). The combined effects of hydrostatic pressure and temperature on the nonlinear optical rectification in lens-shaped InAs QDs are studied under the compact density matrix formalism and the effective mass approximation. From our calculation, it is found that the subband energies and optical rectification susceptibility are quite sensitive to the applied hydrostatic pressure and temperature. The results show that the resonant peak of the optical rectification can be red-shifted or blue-shifted and their intensity also varied by external probes such as hydrostatic pressure and temperature. In addition, the oscillator strength is strongly affected by these parameters. - Highlights: ► Theoretical calculation of the nonlinear optical rectification in a lens shape InAs/GaAs quantum dot was performed. ► Optical rectification susceptibility is quite sensitive to the applied hydrostatic pressure and temperature. ► The oscillator strength is strongly affected by the applied hydrostatic pressure and temperature.

  7. Dynamic simulation of a low-temperature rectification Column as part of an IGCC power plant

    Energy Technology Data Exchange (ETDEWEB)

    Hanke, R. [Leipzig University of Applied Sciences, Department of Mechanical and Energy Engineering, P.O. Box 300066, D-04251 Leipzig (Germany); Hannemann, F. [Siemens AG - Power Generation, PG CTET, P.O. Box 3220, D-91050 Erlangen (Germany); Sundmacher, K. [Max Planck Institute of Dynamics of Complex Technical Systems, Sandtorstrasse 1, D-39106 Magdeburg (Germany); Otto-von-Guericke University Magdeburg, Faculty of Process and Systems Engineering, P.O. Box 4120, D-39106 Magdeburg (Germany)

    2003-11-01

    IGCC plants offer the opportunity to utilize fossil energy sources, like coal or heavy refinery residues, to satisfy increasing energy demand while considering strict environmental constraints. Such a plant consists of a combined power cycle, a fuel gasifier with downstream fuel gas conditioning and an air separation unit (ASU), where the oxygen required for gasification is produced. The low-temperature rectification column as the core of the ASU strongly affects the transient behavior of the system. (Abstract Copyright [2003], Wiley Periodicals, Inc.)

  8. Tuning the Schottky rectification in graphene-hexagonal boron nitride-molybdenum disulfide heterostructure.

    Science.gov (United States)

    Liu, Biao; Zhao, Yu-Qing; Yu, Zhuo-Liang; Wang, Lin-Zhi; Cai, Meng-Qiu

    2018-03-01

    It was still a great challenge to design high performance of rectification characteristic for the rectifier diode. Lately, a new approach was proposed experimentally to tune the Schottky barrier height (SBH) by inserting an ultrathin insulated tunneling layer to form metal-insulator-semiconductor (MIS) heterostructures. However, the electronic properties touching off the high performance of these heterostructures and the possibility of designing more efficient applications for the rectifier diode were not presently clear. In this paper, the structural, electronic and interfacial properties of the novel MIS diode with the graphene/hexagonal boron nitride/monolayer molybdenum disulfide (GBM) heterostructure had been investigated by first-principle calculations. The calculated results showed that the intrinsic properties of graphene and MoS 2 were preserved due to the weak van der Waals contact. The height of interfacial Schottky barrier can be tuned by the different thickness of hBN layers. In addition, the GBM Schottky diode showed more excellent rectification characteristic than that of GM Schottky diode due to the interfacial band bending caused by the epitaxial electric field. Based on the electronic band structure, we analyzed the relationship between the electronic structure and the nature of the Schottky rectifier, and revealed the potential of utilizing GBM Schottky diode for the higher rectification characteristic devices. Copyright © 2017 Elsevier Inc. All rights reserved.

  9. Optical stimulated luminescence (OSL) dating

    International Nuclear Information System (INIS)

    Banerjee, D.

    1999-01-01

    Since the pioneering work by Huntley et al. (1985), optical dating is being increasingly recognised as an important technique for establishing a time frame of deposition of sediments (Aitken, 1998). Optical dating differs from thermoluminescence (TL) dating in that visible/infrared light from lasers or LEDs (light-emitting-diodes) is used as a means of stimulation, in contrast to thermal stimulation. It has several advantages over TL dating: (i) the resetting of the OSL (optically stimulated luminescence) clock is more effective than that of TL clock; for sediments transported under water or in other situations where the sediment grains have undergone inhomogeneous bleaching, this property ensures that ages based on optical dating are generally more reliable than TL ages, (ii) the optical dating technique is non-destructive, and multiple readouts of the optical signal is possible; this feature has resulted in the development of single-aliquot and single-grain protocols (Murray and Wintle, 1999; Banerjee et al. 1999), (iii) the sample is not heated as in TL; thus, spurious luminescence is avoided and there is a significant reduction in blackbody radiation. Dating of materials which change phase on heating is also practical, and finally, (iv) thermal quenching of luminescence is negligible, allowing accurate estimation of kinetic parameters using standard techniques and providing access to deep OSL traps. This characteristic may be helpful in extending the limits of optical dating beyond the last 150 ka from a global point of view

  10. A study on the test of efficiency of the diagnostic X-ray equipment according to their rectifications

    International Nuclear Information System (INIS)

    Seon, Jong Ryul

    1997-01-01

    For the efficient management of the diagnostic x-ray equipment, a nation-wide inspection of hospitals was performed by an inspection institute in Taejon in the first half of 1997. Among those hospitals inspected, 28 equipments(machines) which were over 500 mA were randomly selected according to their characteristics : 7 condenser type x-ray equipments, 7 three control phase of full wave rectification of type remote control x-ray equipments, 7 single phase of full wave rectification type for general radiography equipments, and 7 single phase of full wave rectification type of R/F equipments. We obtained the following results by conducting the experiment based on the efficiency of the equipments mentioned above. 1) When te equipments are analyzed, 2 out of 7 single phase of full wave rectification type of general radiography equipments(28.6%), 3 out of 7 single phase of full wave rectification type of R/F equipments(42.9%), 5 out of 7 three phase of full wave rectification type remote of control x-ray equipments(71.4%), and 4 out of 7 condenser type of x-ray equipments(57.1%) showed suitability. It proves the superiority of the three phase of full wave rectification type of remote control x-ray equipments. 2) From the overall analysis, only about 50% of the equipments(suitability of 14 out of 28) maintain the efficient management. Therefore, maintenance management of equipments is more necessary. If the efficiency of the x-ray equipment is uniformly maintained and managed to prevent the breakdown(trouble) beforehand especially through the continuous inspection of tube voltage, tube current, exposure time, and collimator, the financial loss and exposure dose to the patient, as well as the workers engaged in radiation, can be reduced for better medical service

  11. High-performance noncontact thermal diode via asymmetric nanostructures

    Science.gov (United States)

    Shen, Jiadong; Liu, Xianglei; He, Huan; Wu, Weitao; Liu, Baoan

    2018-05-01

    Electric diodes, though laying the foundation of modern electronics and information processing industries, suffer from ineffectiveness and even failure at high temperatures. Thermal diodes are promising alternatives to relieve above limitations, but usually possess low rectification ratios, and how to obtain a high-performance thermal rectification effect is still an open question. This paper proposes an efficient contactless thermal diode based on the near-field thermal radiation of asymmetric doped silicon nanostructures. The rectification ratio computed via exact scattering theories is demonstrated to be as high as 10 at a nanoscale gap distance and period, outperforming the counterpart flat-plate diode by more than one order of magnitude. This extraordinary performance mainly lies in the higher forward and lower reverse radiative heat flux within the low frequency band compared with the counterpart flat-plate diode, which is caused by a lower loss and smaller cut-off wavevector of nanostructures for the forward and reversed scheme, respectively. This work opens new routes to realize high performance thermal diodes, and may have wide applications in efficient thermal computing, thermal information processing, and thermal management.

  12. Kir2.1 channels set two levels of resting membrane potential with inward rectification.

    Science.gov (United States)

    Chen, Kuihao; Zuo, Dongchuan; Liu, Zheng; Chen, Haijun

    2018-04-01

    Strong inward rectifier K + channels (Kir2.1) mediate background K + currents primarily responsible for maintenance of resting membrane potential. Multiple types of cells exhibit two levels of resting membrane potential. Kir2.1 and K2P1 currents counterbalance, partially accounting for the phenomenon of human cardiomyocytes in subphysiological extracellular K + concentrations or pathological hypokalemic conditions. The mechanism of how Kir2.1 channels contribute to the two levels of resting membrane potential in different types of cells is not well understood. Here we test the hypothesis that Kir2.1 channels set two levels of resting membrane potential with inward rectification. Under hypokalemic conditions, Kir2.1 currents counterbalance HCN2 or HCN4 cation currents in CHO cells that heterologously express both channels, generating N-shaped current-voltage relationships that cross the voltage axis three times and reconstituting two levels of resting membrane potential. Blockade of HCN channels eliminated the phenomenon in K2P1-deficient Kir2.1-expressing human cardiomyocytes derived from induced pluripotent stem cells or CHO cells expressing both Kir2.1 and HCN2 channels. Weakly inward rectifier Kir4.1 or inward rectification-deficient Kir2.1•E224G mutant channels do not set such two levels of resting membrane potential when co-expressed with HCN2 channels in CHO cells or when overexpressed in human cardiomyocytes derived from induced pluripotent stem cells. These findings demonstrate a common mechanism that Kir2.1 channels set two levels of resting membrane potential with inward rectification by balancing inward currents through different cation channels such as hyperpolarization-activated HCN channels or hypokalemia-induced K2P1 leak channels.

  13. Microscale solid-state thermal diodes enabling ambient temperature thermal circuits for energy applications

    KAUST Repository

    Wang, Song

    2017-05-10

    Thermal diodes, or devices that transport thermal energy asymmetrically, analogous to electrical diodes, hold promise for thermal energy harvesting and conservation, as well as for phononics or information processing. The junction of a phase change material and phase invariant material can form a thermal diode; however, there are limited constituent materials available for a given target temperature, particularly near ambient. In this work, we demonstrate that a micro and nanoporous polystyrene foam can house a paraffin-based phase change material, fused to PMMA, to produce mechanically robust, solid-state thermal diodes capable of ambient operation with Young\\'s moduli larger than 11.5 MPa and 55.2 MPa above and below the melting transition point, respectively. Moreover, the composites show significant changes in thermal conductivity above and below the melting point of the constituent paraffin and rectification that is well-described by our previous theory and the Maxwell–Eucken model. Maximum thermal rectifications range from 1.18 to 1.34. We show that such devices perform reliably enough to operate in thermal diode bridges, dynamic thermal circuits capable of transforming oscillating temperature inputs into single polarity temperature differences – analogous to an electrical diode bridge with widespread implications for transient thermal energy harvesting and conservation. Overall, our approach yields mechanically robust, solid-state thermal diodes capable of engineering design from a mathematical model of phase change and thermal transport, with implications for energy harvesting.

  14. Carbohydrate-actuated nanofluidic diode: switchable current rectification in a nanopipette.

    Science.gov (United States)

    Vilozny, Boaz; Wollenberg, Alexander L; Actis, Paolo; Hwang, Daniel; Singaram, Bakthan; Pourmand, Nader

    2013-10-07

    Nanofluidic structures share many properties with ligand-gated ion channels. However, actuating ion conductance in artificial systems is a challenge. We have designed a system that uses a carbohydrate-responsive polymer to modulate ion conductance in a quartz nanopipette. The cationic polymer, a poly(vinylpyridine) quaternized with benzylboronic acid groups, undergoes a transition from swollen to collapsed upon binding to monosaccharides. As a result, the current rectification in nanopipettes can be reversibly switched depending on the concentration of monosaccharides. Such molecular actuation of nanofluidic conductance may be used in novel sensors and drug delivery systems.

  15. Optical rectification, circular photogalvanic effect, and five-wave mixing in optically active liquids

    Science.gov (United States)

    Koroteev, Nikolai I.

    1996-05-01

    A phenomenological analysis is carried out of novel nonlinear optical processes taking place in macroscopically noncentrosymmetric isotropic solutions of chiral (lift-ring mirror asymmetric) macromolecules, which are the primary elements of living organisms and their metabolic products. Among the most interesting and potentially useful for spectroscopic purposes are: optical rectification/photogalvanic effects consisting in electrostatic field/direct electrical current generation in such liquids under irradiation with the intense circularly polarized laser beam and the five-wave mixing phase-matched process of BioCARS to selectively record, background-free, vibrational spectra of chiral molecules.

  16. Tuning characteristics of narrowband THz radiation generated via optical rectification in periodically poled lithium niobate.

    Science.gov (United States)

    Weiss, C; Torosyan, G; Meyn, J P; Wallenstein, R; Beigang, R; Avetisyan, Y

    2001-04-23

    The tuning properties of pulsed narrowband THz radiation generated via optical rectification in periodically poled lithium niobate have been investigated. Using a disk-shaped periodically poled crystal tuning was easily accomplished by rotating the crystal around its axis and observing the generated THz radiation in forward direction. In this way no beam deflection during tuning was observed. The total tuning range extended from 180 GHz up to 830 GHz and was limited by the poling period of 127 microm which determines the maximum THz frequency in forward direction.

  17. Nonlinear optical rectification in semiparabolic quantum wells with an applied electric field

    International Nuclear Information System (INIS)

    Karabulut, ibrahim; Safak, Haluk

    2005-01-01

    The optical rectification (OR) in a semiparabolic quantum well with an applied electric field has been theoretically investigated. The electronic states in a semiparabolic quantum well with an applied electric field are calculated exactly, within the envelope function and the displaced harmonic oscillator approach. Numerical results are presented for the typical Al x Ga 1- x As/GaAs quantum well. These results show that the applied electric field and the confining potential frequency of the semiparabolic quantum well have a great influence on the OR coefficient. Moreover, the OR coefficient also depends sensitively on the relaxation rate of the semiparabolic quantum well system

  18. Note: Electrical detection and quantification of spin rectification effect enabled by shorted microstrip transmission line technique

    International Nuclear Information System (INIS)

    Soh, Wee Tee; Ong, C. K.; Peng, Bin; Chai, Guozhi

    2014-01-01

    We describe a shorted microstrip method for the sensitive quantification of Spin Rectification Effect (SRE). SRE for a Permalloy (Ni 80 Fe 20 ) thin film strip sputtered onto SiO 2 substrate is demonstrated. Our method obviates the need for simultaneous lithographic patterning of the sample and transmission line, therefore greatly simplifying the SRE measurement process. Such a shorted microstrip method can allow different contributions to SRE (anisotropic magnetoresistance, Hall effect, and anomalous Hall effect) to be simultaneously determined. Furthermore, SRE signals from unpatterned 50 nm thick Permalloy films of area dimensions 5 mm × 10 mm can even be detected

  19. Rectification of catalyst separation column at HWP, Thal (Paper No. 5.7)

    International Nuclear Information System (INIS)

    Prakash, R.; Bhaskaran, M.

    1992-01-01

    Heavy Water Plant, Thal is based on the monothermal ammonia hydrogen process. Liquid ammonia containing potassium amide catalyst is contacted with the synthesis gas where-in deuterium from hydrogen gets transferred to liquid phase. There are two parallel streams A and B with a common ammonia synthesis unit. The system is provided with an ammonia cracker and ammonia synthesis for providing the reflux gas and liquid for the enrichment process. The parameters such as steam valve opening, column pressure, reflux, condensate valve opening, cooling water valve position, cracking load of the unit before and after the rectification, etc. are discussed. (author). 2 tabs., 2 figs

  20. Heavy water isotopic rectification in the ''ORPHEE'' reactor. SACLAY studies Centre

    International Nuclear Information System (INIS)

    Lejeune, P.; Breant, P.

    1993-01-01

    ORPHEE reactor supplies neutron beams, which are got back in a heavy water reflector. The neutron beams intensity depends on the reflector quality which is determined by the isotopic content of the heavy water. The deuterium submitted to core irradiation changes in radioactive tritium which must be eliminated largely for reasons of safety. The column must keep the heavy water isotopic content of the reflector to a value higher than 99.8% by eliminating light water by fractional distillation or rectification. This column is also used for the tritium elimination of heavy water. 13 figs

  1. Near-Field Thermal Radiation for Solar Thermophotovoltaics and High Temperature Thermal Logic and Memory Applications

    Science.gov (United States)

    Elzouka, Mahmoud

    This dissertation investigates Near-Field Thermal Radiation (NFTR) applied to MEMS-based concentrated solar thermophotovoltaics (STPV) energy conversion and thermal memory and logics. NFTR is the exchange of thermal radiation energy at nano/microscale; when separation between the hot and cold objects is less than dominant radiation wavelength (˜1 mum). NFTR is particularly of interest to the above applications due to its high rate of energy transfer, exceeding the blackbody limit by orders of magnitude, and its strong dependence on separation gap size, surface nano/microstructure and material properties. Concentrated STPV system converts solar radiation to electricity using heat as an intermediary through a thermally coupled absorber/emitter, which causes STPV to have one of the highest solar-to-electricity conversion efficiency limits (85.4%). Modeling of a near-field concentrated STPV microsystem is carried out to investigate the use of STPV based solid-state energy conversion as high power density MEMS power generator. Numerical results for In 0.18Ga0.82Sb PV cell illuminated with tungsten emitter showed significant enhancement in energy transfer, resulting in output power densities as high as 60 W/cm2; 30 times higher than the equivalent far-field power density. On thermal computing, this dissertation demonstrates near-field heat transfer enabled high temperature NanoThermoMechanical memory and logics. Unlike electronics, NanoThermoMechanical memory and logic devices use heat instead of electricity to record and process data; hence they can operate in harsh environments where electronics typically fail. NanoThermoMechanical devices achieve memory and thermal rectification functions through the coupling of near-field thermal radiation and thermal expansion in microstructures, resulting in nonlinear heat transfer between two temperature terminals. Numerical modeling of a conceptual NanoThermoMechanical is carried out; results include the dynamic response under

  2. Dating and Sexual Feelings

    Science.gov (United States)

    ... Home Body Your sexuality Dating and sexual feelings Dating and sexual feelings Thinking about romance, starting to ... you learn how to stay healthy and strong. Dating older guys top If you date someone even ...

  3. Investigation of the difference between spin Hall magnetoresistance rectification and spin pumping from the viewpoint of magnetization dynamics

    Science.gov (United States)

    Zhang, Qihan; Fan, Xiaolong; Zhou, Hengan; Kong, Wenwen; Zhou, Shiming; Gui, Y. S.; Hu, C.-M.; Xue, Desheng

    2018-02-01

    Spin pumping (SP) and spin rectification due to spin Hall magnetoresistance (SMR) can result in a dc resonant voltage signal, when magnetization in ferromagnetic insulator/nonmagnetic structures experiences ferromagnetic resonance. Since the two effects are often interrelated, quantitative identification of them is important for studying the dynamic nonlocal spin transport through an interface. In this letter, the key difference between SP and SMR rectification was investigated from the viewpoint of spin dynamics. The phase-dependent nature of SMR rectification, which is the fundamental characteristic distinguishing it from SP, was tested by a well-designed experiment. In this experiment, two identical yttrium iron garnet/Pt strips with a π phase difference in dynamic magnetization show the same SP signals and inverse SMR signals.

  4. Setting a date

    International Nuclear Information System (INIS)

    Moore, Glenis.

    1987-01-01

    Dating techniques are discussed and explained. The age range and sensitivity of different techniques are given. Potassium/argon dating, amino-acid dating, radiocarbon dating, dendrochronology, thermoluminescence and geomagnetic field dating are all mentioned. Each technique is explained and a brief history given. The techniques and equipment used by the British Museum, and some examples of archaeological articles dated are mentioned. (UK)

  5. Poly(3-hexylthiophene)/multiwalled carbon hybrid coaxial nanotubes: nanoscale rectification and photovoltaic characteristics.

    Science.gov (United States)

    Kim, Kihyun; Shin, Ji Won; Lee, Yong Baek; Cho, Mi Yeon; Lee, Suk Ho; Park, Dong Hyuk; Jang, Dong Kyu; Lee, Cheol Jin; Joo, Jinsoo

    2010-07-27

    We fabricate hybrid coaxial nanotubes (NTs) of multiwalled carbon nanotubes (MWCNTs) coated with light-emitting poly(3-hexylthiophene) (P3HT). The p-type P3HT material with a thickness of approximately 20 nm is electrochemically deposited onto the surface of the MWCNT. The formation of hybrid coaxial NTs of the P3HT/MWCNT is confirmed by a transmission electron microscope, FT-IR, and Raman spectra. The optical and structural properties of the hybrid NTs are characterized using ultraviolet and visible absorption, Raman, and photoluminescence (PL) spectra where, it is shown that the PL intensity of the P3HT materials decreases after the hybridization with the MWCNTs. The current-voltage (I-V) characteristics of the outer P3HT single NT show the semiconducting behavior, while ohmic behavior is observed for the inner single MWCNT. The I-V characteristics of the hybrid junction between the outer P3HT NT and the inner MWCNT, for the hybrid single NT, exhibit the characteristics of a diode (i.e., rectification), whose efficiency is clearly enhanced with light irradiation. The rectification effect of the hybrid single NT has been analyzed in terms of charge tunneling models. The quasi-photovoltaic effect is also observed at low bias for the P3HT/MWCNT hybrid single NT.

  6. RF Rectification on LAPD and NSTX: the relationship between rectified currents and potentials

    Science.gov (United States)

    Perkins, R. J.; Carter, T.; Caughman, J. B.; van Compernolle, B.; Gekelman, W.; Hosea, J. C.; Jaworski, M. A.; Kramer, G. J.; Lau, C.; Martin, E. H.; Pribyl, P.; Tripathi, S. K. P.; Vincena, S.

    2017-10-01

    RF rectification is a sheath phenomenon important in the fusion community for impurity injection, hot spot formation on plasma-facing components, modifications of the scrape-off layer, and as a far-field sink of wave power. The latter is of particular concern for the National Spherical Torus eXperiment (NSTX), where a substantial fraction of the fast-wave power is lost to the divertor along scrape-off layer field lines. To assess the relationship between rectified currents and rectified voltages, detailed experiments have been performed on the Large Plasma Device (LAPD). An electron current is measured flowing out of the antenna and into the limiters, consistent with RF rectification with a higher RF potential at the antenna. The scaling of this current with RF power will be presented. The limiters are also floated to inhibit this DC current; the impact of this change on plasma-potential and wave-field measurements will be shown. Comparison to data from divertor probes in NSTX will be made. These experiments on a flexible mid-sized experiment will provide insight and guidance into the effects of ICRF on the edge plasma in larger fusion experiments. Funded by the DOE OFES (DE-FC02-07ER54918 and DE-AC02-09CH11466), NSF (NSF- PHY 1036140), and the Univ. of California (12-LR- 237124).

  7. Nanoscale rectenna for broadband rectification of light from infrared to visible

    Science.gov (United States)

    Zimmerman, Darin; Chen, James; Phillips, Michael; Rager, Dennis; Sinisi, Zachary; Wambold, Raymond; Weisel, Gary; Weiss, Brock; Willis, Brian; Miskovsky, Nicholas

    2014-03-01

    We describe a novel approach to the efficient collection and rectification of solar radiation in a device designed to operate from the infrared through the visible. Here, a nanoscale, rectenna array acts both as an absorber of incident radiation and as a rectifier. Rectification derives not from temperature or material asymmetry, as with metal-insulator-metal or silicon-based, Schottky diodes. Instead, it derives from the geometric asymmetry of the rectenna, which is composed of a pointed tip and a flat collector anode. In this arrangement, the difference between the potential barriers for forward and reverse bias results in a rectified dc current. To achieve anode-cathode gap distances within the tunneling regime, we employ selective atomic-layer deposition of copper applied to palladium rectenna arrays produced by electron-beam lithography. We present details of device fabrication and preliminary results of computer simulation, optical characterization, and electro-optical response. This work supported in part by the National Science Foundation: ECCS-1231248 and ECCS-1231313.

  8. Outward Rectification of Voltage-Gated K+ Channels Evolved at Least Twice in Life History.

    Directory of Open Access Journals (Sweden)

    Janin Riedelsberger

    Full Text Available Voltage-gated potassium (K+ channels are present in all living systems. Despite high structural similarities in the transmembrane domains (TMD, this K+ channel type segregates into at least two main functional categories-hyperpolarization-activated, inward-rectifying (Kin and depolarization-activated, outward-rectifying (Kout channels. Voltage-gated K+ channels sense the membrane voltage via a voltage-sensing domain that is connected to the conduction pathway of the channel. It has been shown that the voltage-sensing mechanism is the same in Kin and Kout channels, but its performance results in opposite pore conformations. It is not known how the different coupling of voltage-sensor and pore is implemented. Here, we studied sequence and structural data of voltage-gated K+ channels from animals and plants with emphasis on the property of opposite rectification. We identified structural hotspots that alone allow already the distinction between Kin and Kout channels. Among them is a loop between TMD S5 and the pore that is very short in animal Kout, longer in plant and animal Kin and the longest in plant Kout channels. In combination with further structural and phylogenetic analyses this finding suggests that outward-rectification evolved twice and independently in the animal and plant kingdom.

  9. Fabrication of hydrogel-coated single conical nanochannels exhibiting controllable ion rectification characteristics.

    Science.gov (United States)

    Wang, Linlin; Zhang, Huacheng; Yang, Zhe; Zhou, Jianjun; Wen, Liping; Li, Lin; Jiang, Lei

    2015-03-07

    Heterogeneous nanochannel materials that endow new functionalities different to the intrinsic properties of two original nanoporous materials have wide potential applications in nanofluidics, energy conversion, and biosensors. Herein, we report novel, interesting hydrogel-composited nanochannel devices with regulatable ion rectification characteristics. The heterogeneous nanochannel devices were constructed by selectively coating the tip side, base side, or both sides of a single conical nanochannel membrane with thin agar hydrogel layers. The tunable ion current rectification of the nanochannels in the three different coating states was systematically demonstrated by current-voltage (I-V) curves. The asymmetric ionic transport property of the conical nanochannel was further strengthened in the tip-coating state and weakened in the base-coating state, whereas the conical nanochannel showed nearly symmetric ionic transport in the dual-coating state. Repeated experiments presented insight into the good stability and reversibility of the three coating states of the hydrogel-nanochannel-integrated systems. This work, as an example, may provide a new strategy to further design and develop multifunctional gel-nanochannel heterogeneous smart porous nanomaterials.

  10. The Gravity of Photons and the Necessary Rectification of Einstein Equation

    Directory of Open Access Journals (Sweden)

    Lo C. Y.

    2006-01-01

    Full Text Available It is pointed out that Special Relativity together with the principle of causality implies that the gravity of an electromagnetic wave is an accompanying gravitational wave propagating with the same speed. Since a gravitational wave carries energy-momentum, this accompanying wave would make the energy-stress tensor of the light to be different from the electromagnetic energy-stress tensor, and thus can produce a geodesic equation for the photons. Moreover, it is found that the appropriate Einstein equation must additionally have the photonic energy-stress tensor with the antigravity coupling in the source term. This would correct that, in disagreement with the calculations for the bending of light, existing solutions of gravity for an electromagnetic wave, is unbounded. This rectification is confirmed by calculating the gravity of electromagnetic plane-waves. The gravity of an electromagnetic wave is indeed an accompanying gravitational wave. Moreover, these calculations show the first time that Special Relativity and General Relativity are compatible because the physical meaning of coordinates has been clarified. The success of this rectification makes General Relativity standing out further among theories of gravity.

  11. Pore structure and function of synthetic nanopores with fixed charges: tip shape and rectification properties

    Energy Technology Data Exchange (ETDEWEB)

    RamIrez, Patricio [Departament de Fisica Aplicada, Universitat Politecnica de Valencia, E-46022 Valencia (Spain); Apel, Pavel Yu [Flerov Laboratory of Nuclear Reactions, Joint Institute for Nuclear Research, Joliot-Curie street 6, 141980 Dubna (Russian Federation); Cervera, Javier; Mafe, Salvador [Departament de Fisica de la Terra i Termodinamica, Universitat de Valencia, E-46100 Burjassot (Spain)], E-mail: patraho@fis.upv.es

    2008-08-06

    We present a complete theoretical study of the relationship between the structure (tip shape and dimensions) and function (selectivity and rectification) of asymmetric nanopores on the basis of previous experimental studies. The theoretical model uses a continuum approach based on the Nernst-Planck equations. According to our results, the nanopore transport properties, such as current-voltage (I-V) characteristics, conductance, rectification ratio, and selectivity, are dictated mainly by the shape of the pore tip (we have distinguished bullet-like, conical, trumpet-like, and hybrid shapes) and the concentration of pore surface charges. As a consequence, the nanopore performance in practical applications will depend not only on the base and tip openings but also on the pore shape. In particular, we show that the pore opening dimensions estimated from the pore conductance can be very different, depending on the pore shape assumed. The results obtained can also be of practical relevance for the design of nanopores, nanopipettes, and nanoelectrodes, where the electrical interactions between the charges attached to the nanostructure and the mobile charges confined in the reduced volume of the inside solution dictate the device performance in practical applications. Because single tracks are the elementary building blocks for nanoporous membranes, the understanding and control of their individual properties should also be crucial in protein separation, water desalination, and bio-molecule detection using arrays of identical nanopores.

  12. Pore structure and function of synthetic nanopores with fixed charges: tip shape and rectification properties

    International Nuclear Information System (INIS)

    RamIrez, Patricio; Apel, Pavel Yu; Cervera, Javier; Mafe, Salvador

    2008-01-01

    We present a complete theoretical study of the relationship between the structure (tip shape and dimensions) and function (selectivity and rectification) of asymmetric nanopores on the basis of previous experimental studies. The theoretical model uses a continuum approach based on the Nernst-Planck equations. According to our results, the nanopore transport properties, such as current-voltage (I-V) characteristics, conductance, rectification ratio, and selectivity, are dictated mainly by the shape of the pore tip (we have distinguished bullet-like, conical, trumpet-like, and hybrid shapes) and the concentration of pore surface charges. As a consequence, the nanopore performance in practical applications will depend not only on the base and tip openings but also on the pore shape. In particular, we show that the pore opening dimensions estimated from the pore conductance can be very different, depending on the pore shape assumed. The results obtained can also be of practical relevance for the design of nanopores, nanopipettes, and nanoelectrodes, where the electrical interactions between the charges attached to the nanostructure and the mobile charges confined in the reduced volume of the inside solution dictate the device performance in practical applications. Because single tracks are the elementary building blocks for nanoporous membranes, the understanding and control of their individual properties should also be crucial in protein separation, water desalination, and bio-molecule detection using arrays of identical nanopores

  13. Pore structure and function of synthetic nanopores with fixed charges: tip shape and rectification properties.

    Science.gov (United States)

    Ramírez, Patricio; Apel, Pavel Yu; Cervera, Javier; Mafé, Salvador

    2008-08-06

    We present a complete theoretical study of the relationship between the structure (tip shape and dimensions) and function (selectivity and rectification) of asymmetric nanopores on the basis of previous experimental studies. The theoretical model uses a continuum approach based on the Nernst-Planck equations. According to our results, the nanopore transport properties, such as current-voltage (I-V) characteristics, conductance, rectification ratio, and selectivity, are dictated mainly by the shape of the pore tip (we have distinguished bullet-like, conical, trumpet-like, and hybrid shapes) and the concentration of pore surface charges. As a consequence, the nanopore performance in practical applications will depend not only on the base and tip openings but also on the pore shape. In particular, we show that the pore opening dimensions estimated from the pore conductance can be very different, depending on the pore shape assumed. The results obtained can also be of practical relevance for the design of nanopores, nanopipettes, and nanoelectrodes, where the electrical interactions between the charges attached to the nanostructure and the mobile charges confined in the reduced volume of the inside solution dictate the device performance in practical applications. Because single tracks are the elementary building blocks for nanoporous membranes, the understanding and control of their individual properties should also be crucial in protein separation, water desalination, and bio-molecule detection using arrays of identical nanopores.

  14. Electrical Rectification

    Indian Academy of Sciences (India)

    user

    bio-mimetic systems. O w ing to the saturation of the e± ciency of sil- icon devices in electronics industry, m olecular electronics has gained trem endous im petus in re- cent tim es. T heoretical predictions and experi- m ental realizations of such system s have given birth to a ... their electrical conductance property and pos-.

  15. Nano scale Devices for Rectification of High Frequency Radiation from the Infrared through the Visible: A New Approach

    International Nuclear Information System (INIS)

    Miskovsky, N.M.; Cutler, P.H.; Miskovsky, N.M.; Cutler, P.H.; Lerne, P.B.; Mayer, A.; Weiss, B.L.; Willis, B.; Sullivan, T.E.

    2012-01-01

    We present a new and viable method for optical rectification. This approach has been demonstrated both theoretically and experimentally and is the basis fot the development of devices to rectify radiation through the visible. This technique for rectification is based not on conventional material or temperature asymmetry as used in MIM (metal/insulator/metal) or Schottky diodes, but on a purely sharp geometric property of the antenna. This sharp tip or edge with a collector anode constitutes a tunnel junction. In these devices the rectenna (consisting of the antenna and the tunnel junction) acts as the absorber of the incident radiation and the rectifier. Using current nano fabrication techniques and the selective atomic layer deposition (ALD) process, junctions of 1?nm can be fabricated, which allow for rectification of frequencies up to the blue portion of the spectrum. To assess the viability of our approach, we review the development of nano antenna structures and tunnel junctions capable of operating in the visible region. In addition, we review the detailed process of rectification and present methodologies for analysis of diode data. Finally, we present operational designs for an optical rectenna and its fabrication and discuss outstanding problems and future work.

  16. Nanoscale Devices for Rectification of High Frequency Radiation from the Infrared through the Visible: A New Approach

    Directory of Open Access Journals (Sweden)

    N. M. Miskovsky

    2012-01-01

    Full Text Available We present a new and viable method for optical rectification. This approach has been demonstrated both theoretically and experimentally and is the basis fot the development of devices to rectify radiation through the visible. This technique for rectification is based not on conventional material or temperature asymmetry as used in MIM (metal/insulator/metal or Schottky diodes, but on a purely sharp geometric property of the antenna. This sharp “tip” or edge with a collector anode constitutes a tunnel junction. In these devices the rectenna (consisting of the antenna and the tunnel junction acts as the absorber of the incident radiation and the rectifier. Using current nanofabrication techniques and the selective atomic layer deposition (ALD process, junctions of 1 nm can be fabricated, which allow for rectification of frequencies up to the blue portion of the spectrum. To assess the viability of our approach, we review the development of nanoantenna structures and tunnel junctions capable of operating in the visible region. In addition, we review the detailed process of rectification and present methodologies for analysis of diode data. Finally, we present operational designs for an optical rectenna and its fabrication and discuss outstanding problems and future work.

  17. Rectification of Current Responds to Incorporation of Fullerenes into Mixed-Monolayers of Alkanethiolates in Tunneling Junctions

    NARCIS (Netherlands)

    Qiu, Li; Zhang, Yanxi; Krijger, Theodorus; Qiu, Xinkai; van 't Hof, Patrick; Hummelen, Jan; Chiechi, Ryan

    2016-01-01

    This paper describes the rectification of current through molecular junctions comprising self-assembled monolayers of decanethiolate through the incorporation of C60 fullerene moieties bearing undecanethiol groups in junctions using eutectic Ga–In (EGaIn) and Au conducting probe AFM (CP-AFM)

  18. Understanding Teen Dating Violence

    Science.gov (United States)

    Understanding Teen Dating Violence Fact Sheet 2014 Dating violence is a type of intimate partner violence. It occurs between two people in a close relationship. The nature of dating violence can be physical, emotional, or sexual. • Physical— This ...

  19. Teen Dating Violence

    Science.gov (United States)

    ... Room Social Media Publications Injury Center Teen Dating Violence Recommend on Facebook Tweet Share Compartir On This ... serious forms of violence. What is teen dating violence? Teen Dating Violence [550 KB, 2 Pages, 508] ...

  20. Present Payments, Past Wrongs: Correcting Loose Talk about Nozick and Rectification

    Directory of Open Access Journals (Sweden)

    Jan Narveson

    2009-01-01

    Full Text Available It is widely thought that Robert Nozick’s views on rectification of past injustices are of critical importance to his theory of distributive justice, even perhaps justifying wholesale redistributive taxes in the present because of the undoubted injustices that have pervaded much past history. This essay undertakes to correct this impression—not mostly by disagreeing with Nozick’s claims, but nevertheless proceeding on basic libertarian theory. Of enormous importance is the role of putative innocents, who are defrauded by miscreants carefully covering their tracks so that these recipients have no reason to think they are buying stolen property. But of equal importance is simply that the duty to rectify past injustices is not comparable to the original duty to respect property rights in the first place.

  1. Poly-benzyl domains grown on porous silicon and their I-V rectification

    International Nuclear Information System (INIS)

    Chao Jie; Han Huanmei; Xia Bing; Ba Long; Liu Hongbo; Xiao Shoujun

    2007-01-01

    Microwave-irradiated polymerization of benzyl chloride and triphenyl chloromethane on hydride-terminated porous silicon (PS) was achieved through the use of Zn powder as a catalyst. Transmission infrared Fourier-transform spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) analyses confirmed the poly-benzyl membranes grafted on PS. Topographical images by AFM revealed crystal-like domains rather than homogenous monolayers on the surface. The current-voltage measurements in nano-scale by current sensing atomic force microscopy (CS-AFM) showed the rectification behavior of this polymer membrane. Finally, mechanism of a radical initiation on the surface and a following Friedel-Crafts alkylation was proposed for the covalent assembly of poly-benzyl domains

  2. Experimental results of rectification and filtration from an offshore wave energy system

    Energy Technology Data Exchange (ETDEWEB)

    Bostroem, C.; Staalberg, M.; Thorburn, K.; Leijon, M. [Swedish Centre for Renewable Electric Energy Conversion, Division for Electricity Research, Department of Engineering Science, Uppsala University, Box 534, 75121 Uppsala (Sweden); Lejerskog, E. [Seabased Industry AB, Dag Hammarskjoelds vaeg 52b, 75183 Uppsala (Sweden)

    2009-05-15

    The present paper presents results from a wave energy conversion that is based on a direct drive linear generator. The linear generator is placed on the seabed and connected to a buoy via a rope. Thereby, the natural wave motion is transferred to the translator by the buoy motion. When using direct drive generators, voltage and current output will have varying frequency and varying amplitude and the power must be converted before a grid connection. The electrical system is therefore an important part to study in the complete conversion system from wave energy to grid connected power. This paper will bring up the first steps in the conversion: rectification and filtration of the power. Both simulation studies and offshore experiments have been made. The results indicate that this kind of system works in a satisfactory way and a smooth DC power can be achieved with one linear generator. (author)

  3. A Method for Automatic Image Rectification and Stitching for Vehicle Yaw Marks Trajectory Estimation

    Directory of Open Access Journals (Sweden)

    Vidas Žuraulis

    2016-02-01

    Full Text Available The aim of this study has been to propose a new method for automatic rectification and stitching of the images taken on the accident site. The proposed method does not require any measurements to be performed on the accident site and thus it is frsjebalaee of measurement errors. The experimental investigation was performed in order to compare the vehicle trajectory estimation according to the yaw marks in the stitched image and the trajectory, reconstructed using the GPS data. The overall mean error of the trajectory reconstruction, produced by the method proposed in this paper was 0.086 m. It was only 0.18% comparing to the whole trajectory length.

  4. Electric field controlled reversible magnetic anisotropy switching studied by spin rectification

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Hengan; Fan, Xiaolong, E-mail: fanxiaolong@lzu.edu.cn; Wang, Fenglong; Jiang, Changjun; Rao, Jinwei; Zhao, Xiaobing; Xue, Desheng [Key Laboratory for Magnetism and Magnetic Materials of Ministry of Education, Lanzhou University, Lanzhou 730000 (China); Gui, Y. S.; Hu, C.-M. [Department of Physics and Astronomy, University of Manitoba, Winnipeg, Manitoba R3T 2N2 (Canada)

    2014-03-10

    In this letter, spin rectification was used to study the electric field controlled dynamic magnetic properties of the multiferroic composite which is a Co stripe with induced in-plane anisotropy deposited onto a Pb(Mg{sub 1∕3}Nb{sub 2∕3})O{sub 3}-PbTiO{sub 3} substrate. Due to the coupling between piezoelectric and magnetoelastic effects, a reversible in-plane anisotropy switching has been realized by varying the history of the applied electric field. This merit results from the electric hysteresis of the polarization in the nonlinear piezoelectric regime, which has been proved by a butterfly type electric field dependence of the in-plane anisotropy field. Moreover, the electric field dependent effective demagnetization field and linewidth have been observed at the same time.

  5. Rectification of harmonically oscillating magnetic fields in quarter circular Josephson junctions

    International Nuclear Information System (INIS)

    Shaju, P.D.; Kuriakose, V.C.

    2003-01-01

    A novel method for rectifying harmonically varying magnetic fields is demonstrated using fluxons in quarter circular Josephson junctions (JJs). A JJ with a quarter circular geometry terminated with a load resistor at one end is found to be capable of rectifying alternating fields when biased with a constant dc current. An external magnetic field applied parallel to the dielectric barrier of the junction interacts with the edges of the junction and make asymmetric boundary conditions. These asymmetric boundary conditions facilitate fluxon penetration under a dc bias from one end of the junction in alternate half cycles of the applied field. Thus effective rectification of the field can be achieved using quarter circular JJs. This unique phenomenon is specific to this geometry and can be exploited for making superconducting magnetic field rectifiers. This proposed device is expected to have important applications in millimeter and sub-millimeter radio wave astronomy

  6. Electric field controlled reversible magnetic anisotropy switching studied by spin rectification

    International Nuclear Information System (INIS)

    Zhou, Hengan; Fan, Xiaolong; Wang, Fenglong; Jiang, Changjun; Rao, Jinwei; Zhao, Xiaobing; Xue, Desheng; Gui, Y. S.; Hu, C.-M.

    2014-01-01

    In this letter, spin rectification was used to study the electric field controlled dynamic magnetic properties of the multiferroic composite which is a Co stripe with induced in-plane anisotropy deposited onto a Pb(Mg 1∕3 Nb 2∕3 )O 3 -PbTiO 3 substrate. Due to the coupling between piezoelectric and magnetoelastic effects, a reversible in-plane anisotropy switching has been realized by varying the history of the applied electric field. This merit results from the electric hysteresis of the polarization in the nonlinear piezoelectric regime, which has been proved by a butterfly type electric field dependence of the in-plane anisotropy field. Moreover, the electric field dependent effective demagnetization field and linewidth have been observed at the same time

  7. Separating inverse spin Hall voltage and spin rectification voltage by inverting spin injection direction

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Wenxu, E-mail: xwzhang@uestc.edu.cn; Peng, Bin; Han, Fangbin; Wang, Qiuru; Zhang, Wanli [State Key Laboratory of Electronic Thin Films and Integrated Devices, University of Electronic Science and Technology of China, Chengdu 610054 (China); Soh, Wee Tee; Ong, Chong Kim [Center for Superconducting and Magnetic Materials, Department of Physics, National University of Singapore, 2 Science Drive 3, Singapore 117551 (Singapore)

    2016-03-07

    We develop a method for universally resolving the important issue of separating the inverse spin Hall effect (ISHE) from the spin rectification effect (SRE) signal. This method is based on the consideration that the two effects depend on the spin injection direction: The ISHE is an odd function of the spin injection direction while the SRE is independent on it. Thus, the inversion of the spin injection direction changes the ISHE voltage signal, while the SRE voltage remains. It applies generally to analyzing the different voltage contributions without fitting them to special line shapes. This fast and simple method can be used in a wide frequency range and has the flexibility of sample preparation.

  8. Rectification induced in N2AA-doped armchair graphene nanoribbon device

    International Nuclear Information System (INIS)

    Chen, Tong; Wang, Ling-Ling; Luo, Kai-Wu; Xu, Liang; Li, Xiao-Fei

    2014-01-01

    By using non-equilibrium Green function formalism in combination with density functional theory, we investigated the electronic transport properties of armchair graphene nanoribbon devices in which one lead is undoped and the other is N 2 AA -doped with two quasi-adjacent substitutional nitrogen atoms incorporating pairs of neighboring carbon atoms in the same sublattice A. Two kinds of N 2 AA -doped style are considered, for N dopants substitute the center or the edge carbon atoms. Our results show that the rectification behavior with a large rectifying ratio can be found in these devices and the rectifying characteristics can be modulated by changing the width of graphene nanoribbons or the position of the N 2 AA dopant. The mechanisms are revealed to explain the rectifying behaviors.

  9. Fast noise level estimation algorithm based on principal component analysis transform and nonlinear rectification

    Science.gov (United States)

    Xu, Shaoping; Zeng, Xiaoxia; Jiang, Yinnan; Tang, Yiling

    2018-01-01

    We proposed a noniterative principal component analysis (PCA)-based noise level estimation (NLE) algorithm that addresses the problem of estimating the noise level with a two-step scheme. First, we randomly extracted a number of raw patches from a given noisy image and took the smallest eigenvalue of the covariance matrix of the raw patches as the preliminary estimation of the noise level. Next, the final estimation was directly obtained with a nonlinear mapping (rectification) function that was trained on some representative noisy images corrupted with different known noise levels. Compared with the state-of-art NLE algorithms, the experiment results show that the proposed NLE algorithm can reliably infer the noise level and has robust performance over a wide range of image contents and noise levels, showing a good compromise between speed and accuracy in general.

  10. In Vivo Demonstration of Addressable Microstimulators Powered by Rectification of Epidermically Applied Currents for Miniaturized Neuroprostheses.

    Science.gov (United States)

    Becerra-Fajardo, Laura; Ivorra, Antoni

    2015-01-01

    Electrical stimulation is used in order to restore nerve mediated functions in patients with neurological disorders, but its applicability is constrained by the invasiveness of the systems required to perform it. As an alternative to implantable systems consisting of central stimulation units wired to the stimulation electrodes, networks of wireless microstimulators have been devised for fine movement restoration. Miniaturization of these microstimulators is currently hampered by the available methods for powering them. Previously, we have proposed and demonstrated a heterodox electrical stimulation method based on electronic rectification of high frequency current bursts. These bursts can be delivered through textile electrodes on the skin. This approach has the potential to result in an unprecedented level of miniaturization as no bulky parts such as coils or batteries are included in the implant. We envision microstimulators designs based on application-specific integrated circuits (ASICs) that will be flexible, thread-like (diameters electrical stimulation method are feasible and can perform controlled charge-balanced electrical stimulation of muscles. We developed miniature external circuit prototypes connected to two bipolar probes that were percutaneously implanted in agonist and antagonist muscles of the hindlimb of an anesthetized rabbit. The electronic implant architecture was able to decode commands that were amplitude modulated on the high frequency (1 MHz) auxiliary current bursts. The devices were capable of independently stimulating the target tissues, accomplishing controlled dorsiflexion and plantarflexion joint movements. In addition, we numerically show that the high frequency current bursts comply with safety standards both in terms of tissue heating and unwanted electro-stimulation. We demonstrate that addressable microstimulators powered by rectification of epidermically applied currents are feasible.

  11. Interannual variability in the atmospheric CO2 rectification over a boreal forest region

    Science.gov (United States)

    Chen, Baozhang; Chen, Jing M.; Worthy, Douglas E. J.

    2005-08-01

    Ecosystem CO2 exchange with the atmosphere and the planetary boundary layer (PBL) dynamics are correlated diurnally and seasonally. The strength of this kind of covariation is quantified as the rectifier effect, and it affects the vertical gradient of CO2 and thus the global CO2 distribution pattern. An 11-year (1990-1996, 1999-2002), continuous CO2 record from Fraserdale, Ontario (49°52'29.9″N, 81°34'12.3″W), along with a coupled vertical diffusion scheme (VDS) and ecosystem model named Boreal Ecosystem Productivity Simulator (BEPS), are used to investigate the interannual variability of the rectifier effect over a boreal forest region. The coupled model performed well (r2 = 0.70 and 0.87, at 40 m at hourly and daily time steps, respectively) in simulating CO2 vertical diffusion processes. The simulated annual atmospheric rectifier effect varies from 3.99 to 5.52 ppm, while the diurnal rectifying effect accounted for about a quarter of the annual total (22.8˜28.9%).The atmospheric rectification of CO2 is not simply influenced by terrestrial source and sink strengths, but by seasonal and diurnal variations in the land CO2 flux and their interaction with PBL dynamics. Air temperature and moisture are found to be the dominant climatic factors controlling the rectifier effect. The annual rectifier effect is highly correlated with annual mean temperature (r2 = 0.84), while annual mean air relative humidity can explain 51% of the interannual variation in rectification. Seasonal rectifier effect is also found to be more sensitive to climate variability than diurnal rectifier effect.

  12. In Vivo Demonstration of Addressable Microstimulators Powered by Rectification of Epidermically Applied Currents for Miniaturized Neuroprostheses.

    Directory of Open Access Journals (Sweden)

    Laura Becerra-Fajardo

    Full Text Available Electrical stimulation is used in order to restore nerve mediated functions in patients with neurological disorders, but its applicability is constrained by the invasiveness of the systems required to perform it. As an alternative to implantable systems consisting of central stimulation units wired to the stimulation electrodes, networks of wireless microstimulators have been devised for fine movement restoration. Miniaturization of these microstimulators is currently hampered by the available methods for powering them. Previously, we have proposed and demonstrated a heterodox electrical stimulation method based on electronic rectification of high frequency current bursts. These bursts can be delivered through textile electrodes on the skin. This approach has the potential to result in an unprecedented level of miniaturization as no bulky parts such as coils or batteries are included in the implant. We envision microstimulators designs based on application-specific integrated circuits (ASICs that will be flexible, thread-like (diameters < 0.5 mm and not only with controlled stimulation capabilities but also with sensing capabilities for artificial proprioception. We in vivo demonstrate that neuroprostheses composed of addressable microstimulators based on this electrical stimulation method are feasible and can perform controlled charge-balanced electrical stimulation of muscles. We developed miniature external circuit prototypes connected to two bipolar probes that were percutaneously implanted in agonist and antagonist muscles of the hindlimb of an anesthetized rabbit. The electronic implant architecture was able to decode commands that were amplitude modulated on the high frequency (1 MHz auxiliary current bursts. The devices were capable of independently stimulating the target tissues, accomplishing controlled dorsiflexion and plantarflexion joint movements. In addition, we numerically show that the high frequency current bursts comply with

  13. Development of a thermally switched superconducting rectifier for 100 kA

    NARCIS (Netherlands)

    Mulder, G.B.J.; Mulder, G.B.J.; ten Kate, Herman H.J.; Krooshoop, Hendrikus J.G.; van de Klundert, L.J.M.; van de Klundert, L.J.M.

    1991-01-01

    A full-wave superconducting rectifier for 100 kA has been developed. Typical design values of this device are: a secondary current of 100 kA, a primary amplitude of 20 A, an operating frequency of 0.5 Hz, and an average power on the order of 100 W. The rectification is achieved by means of thermally

  14. Progress in radiocarbon dating

    International Nuclear Information System (INIS)

    Hedges, R.E.M.

    1985-01-01

    The article concerns radiocarbon dating, the most important method for dating in archaeology. The principles and practice of the dating method are described. Recent developments in radiocarbon dating due to technical advances, are discussed, and include radiometric counting of small samples and accelerator mass spectrometry. Carbon isotopes and the environment are also discussed. (U.K.)

  15. Errors in accident data, its types, causes and methods of rectification-analysis of the literature.

    Science.gov (United States)

    Ahmed, Ashar; Sadullah, Ahmad Farhan Mohd; Yahya, Ahmad Shukri

    2017-07-29

    Most of the decisions taken to improve road safety are based on accident data, which makes it the back bone of any country's road safety system. Errors in this data will lead to misidentification of black spots and hazardous road segments, projection of false estimates pertinent to accidents and fatality rates, and detection of wrong parameters responsible for accident occurrence, thereby making the entire road safety exercise ineffective. Its extent varies from country to country depending upon various factors. Knowing the type of error in the accident data and the factors causing it enables the application of the correct method for its rectification. Therefore there is a need for a systematic literature review that addresses the topic at a global level. This paper fulfils the above research gap by providing a synthesis of literature for the different types of errors found in the accident data of 46 countries across the six regions of the world. The errors are classified and discussed with respect to each type and analysed with respect to income level; assessment with regard to the magnitude for each type is provided; followed by the different causes that result in their occurrence, and the various methods used to address each type of error. Among high-income countries the extent of error in reporting slight, severe, non-fatal and fatal injury accidents varied between 39-82%, 16-52%, 12-84%, and 0-31% respectively. For middle-income countries the error for the same categories varied between 93-98%, 32.5-96%, 34-99% and 0.5-89.5% respectively. The only four studies available for low-income countries showed that the error in reporting non-fatal and fatal accidents varied between 69-80% and 0-61% respectively. The logistic relation of error in accident data reporting, dichotomised at 50%, indicated that as the income level of a country increases the probability of having less error in accident data also increases. Average error in recording information related to the

  16. Date canning: a new approach for the long time preservation of date.

    Science.gov (United States)

    Homayouni, Aziz; Azizi, Aslan; Keshtiban, Ata Khodavirdivand; Amini, Amir; Eslami, Ahad

    2015-04-01

    Dramatic growth in date (Phoenix dactylifera L.) production, makes it clear to apply proper methods to preserve this nutritious fruit for a long time. Numerous methods have been used to gain this goal in recent years that can be classified into non-thermal (fumigation, ozonation, irradiation, and packaging) and thermal (heat treatment, cold storage, dehydration, jam etc.) processing methods. In this paper these methods were reviewed and novel methods for date preservation were presented.

  17. Synaptic excitation in spinal motoneurons alternates with synaptic inhibition and is balanced by outward rectification during rhythmic motor network activity

    DEFF Research Database (Denmark)

    Guzulaitis, Robertas; Hounsgaard, Jorn

    2017-01-01

    channels. Intrinsic outward rectification facilitates spiking by focusing synaptic depolarization near threshold for action potentials. By direct recording of synaptic currents, we also show that motoneurons are activated by out-of-phase peaks in excitation and inhibition during network activity, whereas......Regular firing in spinal motoneurons of red-eared turtles (Trachemys scripta elegans, either sex) evoked by steady depolarization at rest is replaced by irregular firing during functional network activity. The transition caused by increased input conductance and synaptic fluctuations in membrane...... potential was suggested to originate from intense concurrent inhibition and excitation. We show that the conductance increase in motoneurons during functional network activity is mainly caused by intrinsic outward rectification near threshold for action potentials by activation of voltage and Ca2+ gated K...

  18. A new type of accelerator power supply based on voltage-type space vector PWM rectification technology

    International Nuclear Information System (INIS)

    Wu, Fengjun; Gao, Daqing; Shi, Chunfeng; Huang, Yuzhen; Cui, Yuan; Yan, Hongbin; Zhang, Huajian; Wang, Bin; Li, Xiaohui

    2016-01-01

    To solve the problems such as low input power factor, a large number of AC current harmonics and instable DC bus voltage due to the diode or thyristor rectifier used in an accelerator power supply, particularly in the Heavy Ion Research Facility in Lanzhou-Cooler Storage Ring (HIRFL-CSR), we designed and built up a new type of accelerator power supply prototype base on voltage-type space vector PWM (SVPWM) rectification technology. All the control strategies are developed in TMS320C28346, which is a digital signal processor from TI. The experimental results indicate that an accelerator power supply with a SVPWM rectifier can solve the problems above well, and the output performance such as stability, tracking error and ripple current meet the requirements of the design. The achievement of prototype confirms that applying voltage-type SVPWM rectification technology in an accelerator power supply is feasible; and it provides a good reference for design and build of this new type of power supply. - Highlights: • Applying SVPWM rectification technology in an accelerator power supply improves its grid-side performance. • New Topology and its control strategies make an accelerator power supply have bidirectional power flow ability. • Hardware and software of controller provide a good reference for design of this new type of power supply.

  19. Negative differential resistance and rectification effects in zigzag graphene nanoribbon heterojunctions: Induced by edge oxidation and symmetry concept

    Science.gov (United States)

    Nazirfakhr, Maryam; Shahhoseini, Ali

    2018-03-01

    By applying non-equilibrium Green's functions (NEGF) in combination with tight-binding (TB) model, we investigate and compare the electronic transport properties of H-terminated zigzag graphene nanoribbon (H/ZGNR) and O-terminated ZGNR/H-terminated ZGNR (O/ZGNR-H/ZGNR) heterostructure under finite bias. Moreover, the effect of width and symmetry on the electronic transport properties of both models is also considered. The results reveal that asymmetric H/ZGNRs have linear I-V characteristics in whole bias range, but symmetric H-ZGNRs show negative differential resistance (NDR) behavior which is inversely proportional to the width of the H/ZGNR. It is also shown that the I-V characteristic of O/ZGNR-H/ZGNR heterostructure shows a rectification effect, whether the geometrical structure is symmetric or asymmetric. The fewer the number of zigzag chains, the bigger the rectification ratio. It should be mentioned that, the rectification ratios of symmetric heterostructures are much bigger than asymmetric one. Transmission spectrum, density of states (DOS), molecular projected self-consistent Hamiltonian (MPSH) and molecular eigenstates are analyzed subsequently to understand the electronic transport properties of these ZGNR devices. Our findings could be used in developing nanoscale rectifiers and NDR devices.

  20. Intense laser effects on nonlinear optical absorption and optical rectification in single quantum wells under applied electric and magnetic field

    International Nuclear Information System (INIS)

    Duque, C.A.; Kasapoglu, E.; Sakiroglu, S.; Sari, H.; Soekmen, I.

    2011-01-01

    In this work the effects of intense laser on the electron-related nonlinear optical absorption and nonlinear optical rectification in GaAs-Ga 1-x Al x As quantum wells are studied under, applied electric and magnetic field. The electric field is applied along the growth direction of the quantum well whereas the magnetic field has been considered to be in-plane. The calculations were performed within the density matrix formalism with the use of the effective mass and parabolic band approximations. The intense laser effects are included through the Floquet method, by modifying the confining potential associated to the heterostructure. Results are presented for the nonlinear optical absorption, the nonlinear optical rectification and the resonant peak of these two optical processes. Several configurations of the dimensions of the quantum well, the applied electric and magnetic fields, and the incident intense laser radiation have been considered. The outcome of the calculation suggests that the nonlinear optical absorption and optical rectification are non-monotonic functions of the dimensions of the heterostructure and of the external perturbations considered in this work.

  1. A new type of accelerator power supply based on voltage-type space vector PWM rectification technology

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Fengjun, E-mail: wufengjun@impcas.ac.cn [Institute of Modern Physics, CAS, Lanzhou 730000 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Gao, Daqing; Shi, Chunfeng; Huang, Yuzhen [Institute of Modern Physics, CAS, Lanzhou 730000 (China); Cui, Yuan [Institute of Modern Physics, CAS, Lanzhou 730000 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Yan, Hongbin [Institute of Modern Physics, CAS, Lanzhou 730000 (China); Zhang, Huajian [Institute of Modern Physics, CAS, Lanzhou 730000 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Wang, Bin [University of Chinese Academy of Sciences, Beijing 100049 (China); Li, Xiaohui [Institute of Modern Physics, CAS, Lanzhou 730000 (China)

    2016-08-01

    To solve the problems such as low input power factor, a large number of AC current harmonics and instable DC bus voltage due to the diode or thyristor rectifier used in an accelerator power supply, particularly in the Heavy Ion Research Facility in Lanzhou-Cooler Storage Ring (HIRFL-CSR), we designed and built up a new type of accelerator power supply prototype base on voltage-type space vector PWM (SVPWM) rectification technology. All the control strategies are developed in TMS320C28346, which is a digital signal processor from TI. The experimental results indicate that an accelerator power supply with a SVPWM rectifier can solve the problems above well, and the output performance such as stability, tracking error and ripple current meet the requirements of the design. The achievement of prototype confirms that applying voltage-type SVPWM rectification technology in an accelerator power supply is feasible; and it provides a good reference for design and build of this new type of power supply. - Highlights: • Applying SVPWM rectification technology in an accelerator power supply improves its grid-side performance. • New Topology and its control strategies make an accelerator power supply have bidirectional power flow ability. • Hardware and software of controller provide a good reference for design of this new type of power supply.

  2. Recent advances in thermoluminescence dating

    International Nuclear Information System (INIS)

    Aitken, M.J.

    1984-01-01

    Initially the application of thermoluminescent dating was to ancient pottery and other baked clay, the detection of forgeries in art ceramics having a particularly powerful impact. In recent years there has been a growing extension of TL into non-pottery materials. Heated flints from paleolithic fire-places is one application. Another is in the dating of igneous rocks from recent volcanic events; formerly this had been impossible on account of the malign phenomenon of non-thermal ('anomalous') fading exhibited by volcanic minerals but this is now being circumvented by utilising TL in the 600 0 C region of the glow curve. TL dating has also been extended to unburnt calcite, one application being stalagmitic floors in paleolithic caves. Another recent development is the use of TL for dating aeolian sediment and some types of waterborne sediment. These developments give prospect of establishing a TL-based chronology, both for archaeology and quaternary research, extending back well beyond the range of radiocarbon, perhaps reaching a million years ago. (author)

  3. Zero-Shot Learning via Attribute Regression and Class Prototype Rectification.

    Science.gov (United States)

    Luo, Changzhi; Li, Zhetao; Huang, Kaizhu; Feng, Jiashi; Wang, Meng

    2018-02-01

    Zero-shot learning (ZSL) aims at classifying examples for unseen classes (with no training examples) given some other seen classes (with training examples). Most existing approaches exploit intermedia-level information (e.g., attributes) to transfer knowledge from seen classes to unseen classes. A common practice is to first learn projections from samples to attributes on seen classes via a regression method, and then apply such projections to unseen classes directly. However, it turns out that such a manner of learning strategy easily causes projection domain shift problem and hubness problem, which hinder the performance of ZSL task. In this paper, we also formulate ZSL as an attribute regression problem. However, different from general regression-based solutions, the proposed approach is novel in three aspects. First, a class prototype rectification method is proposed to connect the unseen classes to the seen classes. Here, a class prototype refers to a vector representation of a class, and it is also known as a class center, class signature, or class exemplar. Second, an alternating learning scheme is proposed for jointly performing attribute regression and rectifying the class prototypes. Finally, a new objective function which takes into consideration both the attribute regression accuracy and the class prototype discrimination is proposed. By introducing such a solution, domain shift problem and hubness problem can be mitigated. Experimental results on three public datasets (i.e., CUB200-2011, SUN Attribute, and aPaY) well demonstrate the effectiveness of our approach.

  4. Rectification of terahertz radiation in semiconductor superlattices in the absence of domains

    International Nuclear Information System (INIS)

    Isohätälä, J; Alekseev, K N

    2012-01-01

    We study theoretically the dynamical rectification of a terahertz AC electric field, i.e. the DC current and voltage response to the incident radiation, in strongly coupled semiconductor superlattices. We address the problem of stability against electric field domains: a spontaneous DC voltage is known to appear exactly for parameters for which a spatially homogeneous electron distribution is unstable. We show that by applying a weak direct current bias the rectifier can be switched from a state with zero DC voltage to one with a finite voltage in full absence of domains. The switching occurs near the conditions of dynamical symmetry breaking of an unbiased semiconductor superlattice. Therefore our scheme allows for the generation of DC voltages that would otherwise be unreachable due to domain instabilities. Furthermore, for realistic, highly doped wide miniband superlattices at room temperature, the generated DC field can be nearly quantized, that is, be approximately proportional to an integer multiple of ħω/ea where a is the superlattice period and ω is the AC field frequency. (paper)

  5. Toward a nanoimprinted nanoantenna to perform optical rectification through molecular diodes

    Science.gov (United States)

    Reynaud, C. A.; Duché, D.; Ruiz, C. M.; Palanchoke, U.; Patrone, L.; Le Rouzo, J.; Labau, S.; Frolet, N.; Gourgon, C.; Alfonso, C.; Charaï, A.; Lebouin, C.; Simon, J.-J.; Escoubas, L.

    2017-12-01

    This work presents investigations about the realization and modelization of rectenna solar cells. Rectennas are antennas coupled with a rectifier to convert the alternative current originating from the antenna into direct current that can be harvested and stored. By reducing the size of the antennas to the nanoscale, interactions with visible and near-infrared light become possible. If techniques such as nanoimprint lithography make possible the fabrication of sufficiently small plasmonic structures to act as optical antennas, the concept of rectenna still faces several challenges. One of the most critical point is to achieve rectification at optical frequencies. To address this matter, we propose to use molecular diodes (ferrocenyl-alkanethiol) that can be self-assembled on metallic surfaces such as gold or silver. In this paper, we present a basic rectenna theory as well as finite-difference time-domain (FDTD) optical simulations of plasmonic structures and experimental results of both nanoimprint fabrication of samples and characterizations by electron microscopy, Raman spectroscopy, and cyclic voltammetry techniques.

  6. Influence of Magnetic Field on the Rectification Process of Binary Heterogeneous Azeotrope

    Institute of Scientific and Technical Information of China (English)

    JIA Shaoyi; WU Songhai; LI Zhen; JIA Liang

    2005-01-01

    To improve separate effect of binary heterogeneous azeotrope in the magnetic field with different magnetic induction intensity, the influence of magnetic field on the rectification process of binary heterogeneous azeotrope was investigated with 1-butanol-water system. The results show that the composition of liquid-liquid phase equilibrium of 1-butanol-water system has definitely changed, the composition of 1-butanol in light phase (1-butanol layer) increases by 1.17%-1.63% and the composition of water in heavy phase (water layer) increases by 1.21%-1.58% under the influence of magnetic field. By separation of magnetization, the composition of 1-butanol increases by 0.8%-1.2% and the recovery ratio of 1-butanol increases by 1.6%-2.5%. Magnetic field has positive effect, however, the magnetized effect is not in proportion to magnetic induction intensity and has an optimum condition, in the range of 0.25 T-0.3 T.

  7. An Analytical Measuring Rectification Algorithm of Monocular Systems in Dynamic Environment

    Directory of Open Access Journals (Sweden)

    Deshi Li

    2016-01-01

    Full Text Available Range estimation is crucial for maintaining a safe distance, in particular for vision navigation and localization. Monocular autonomous vehicles are appropriate for outdoor environment due to their mobility and operability. However, accurate range estimation using vision system is challenging because of the nonholonomic dynamics and susceptibility of vehicles. In this paper, a measuring rectification algorithm for range estimation under shaking conditions is designed. The proposed method focuses on how to estimate range using monocular vision when a shake occurs and the algorithm only requires the pose variations of the camera to be acquired. Simultaneously, it solves the problem of how to assimilate results from different kinds of sensors. To eliminate measuring errors by shakes, we establish a pose-range variation model. Afterwards, the algebraic relation between distance increment and a camera’s poses variation is formulated. The pose variations are presented in the form of roll, pitch, and yaw angle changes to evaluate the pixel coordinate incensement. To demonstrate the superiority of our proposed algorithm, the approach is validated in a laboratory environment using Pioneer 3-DX robots. The experimental results demonstrate that the proposed approach improves in the range accuracy significantly.

  8. Thermal transport across metal–insulator interface via electron–phonon interaction

    International Nuclear Information System (INIS)

    Zhang, Lifa; Wang, Jian-Sheng; Li, Baowen; Lü, Jing-Tao

    2013-01-01

    The thermal transport across a metal–insulator interface can be characterized by electron–phonon interaction through which an electron lead is coupled to a phonon lead if phonon–phonon coupling at the interface is very weak. We investigate the thermal conductance and rectification between the electron part and the phonon part using the nonequilibrium Green’s function method. It is found that the thermal conductance has a nonmonotonic behavior as a function of average temperature or the coupling strength between the phonon leads in the metal part and the insulator part. The metal–insulator interface shows a clear thermal rectification effect, which can be reversed by a change in average temperature or the electron–phonon coupling. (paper)

  9. Correlates of minimal dating.

    Science.gov (United States)

    Leck, Kira

    2006-10-01

    Researchers have associated minimal dating with numerous factors. The present author tested shyness, introversion, physical attractiveness, performance evaluation, anxiety, social skill, social self-esteem, and loneliness to determine the nature of their relationships with 2 measures of self-reported minimal dating in a sample of 175 college students. For women, shyness, introversion, physical attractiveness, self-rated anxiety, social self-esteem, and loneliness correlated with 1 or both measures of minimal dating. For men, physical attractiveness, observer-rated social skill, social self-esteem, and loneliness correlated with 1 or both measures of minimal dating. The patterns of relationships were not identical for the 2 indicators of minimal dating, indicating the possibility that minimal dating is not a single construct as researchers previously believed. The present author discussed implications and suggestions for future researchers.

  10. Dating of cremated bones

    OpenAIRE

    Lanting, JN; Aerts-Bijma, AT; van der Plicht, J; Boaretto, E.; Carmi, I.

    2001-01-01

    When dating unburnt bone, bone collagen, the organic fraction of the bone, is used. Collagen does not survive the heat of the cremation pyre, so dating of cremated bone has been considered impossible. Structural carbonate in the mineral fraction of the bone, however, survives the cremation process. We developed a method of dating cremated bone by accelerator mass spectrometry (AMS), using this carbonate fraction. Here we present results for a variety of prehistoric sites and ages, showing a r...

  11. Carbon 14 dating method

    International Nuclear Information System (INIS)

    Fortin, Ph.

    2000-01-01

    This document gives a first introduction to 14 C dating as it is put into practice at the radiocarbon dating centre of Claude-Bernard university (Lyon-1 univ., Villeurbanne, France): general considerations and recalls of nuclear physics; the 14 C dating method; the initial standard activity; the isotopic fractioning; the measurement of samples activity; the liquid-scintillation counters; the calibration and correction of 14 C dates; the preparation of samples; the benzene synthesis; the current applications of the method. (J.S.)

  12. Irradiation of dates

    International Nuclear Information System (INIS)

    Farkas, J.; Al-Charchafchy, F.; Al-Shaikhaly, M.H.; Mirjan, J.; Auda, H.

    1974-01-01

    Testing of the technical feasibility of radurization of fresh dates was attempted. In addition preliminary studies were carried out to investigate the applicability of gamma rays to date syrup manufacture. The varieties Zahdi, Lelwi and Tabarzel were studied at different stages of ripening. The eating quality of fresh dates was not affected significantly by irradiation even with doses of 270 and 540 krad. The duration of the softening process, after-ripening, of dates was prolonged by low doses of 10-30 krad in the majority of the experimental batches. The time period of after-ripening was reduced with 270 krad, as well as with 540 krad as a result of shortening of the induction period, i.e. the time after which the date begins to soften. The microbial spoilage of khalaal Lelwi dates was considerably reduced by irradiation with doses above 90 krad. The dibis yield of fully rutab dates was highly increased by the radiation doses of 375 to 2000 krad. The darkness and viable cell count of dibis pressed from irradiated dates were significantly lower than that of untreated dates. (F.J.)

  13. In vivo demonstration of injectable microstimulators based on charge-balanced rectification of epidermically applied currents

    Science.gov (United States)

    Ivorra, Antoni; Becerra-Fajardo, Laura; Castellví, Quim

    2015-12-01

    Objective. It is possible to develop implantable microstimulators whose actuation principle is based on rectification of high-frequency (HF) current bursts supplied through skin electrodes. This has been demonstrated previously by means of devices consisting of a single diode. However, previous single diode devices caused dc currents which made them impractical for clinical applications. Here flexible thread-like stimulation implants which perform charge balance are demonstrated in vivo. Approach. The implants weigh 40.5 mg and they consist of a 3 cm long tubular silicone body with a diameter of 1 mm, two electrodes at opposite ends, and, within the central section of the body, an electronic circuit made up of a diode, two capacitors, and a resistor. In the present study, each implant was percutaneously introduced through a 14 G catheter into either the gastrocnemius muscle or the cranial tibial muscle of a rabbit hindlimb. Then stimulation was performed by delivering HF bursts (amplitude pair of textile electrodes strapped around the hindlimb and either isometric plantarflexion or dorsiflexion forces were recorded. Stimulation was also assayed 1, 2 and 4 weeks after implantation. Main results. The implants produced bursts of rectified current whose mean value was of a few mA and were capable of causing local neuromuscular stimulation. The implants were well-tolerated during the 4 weeks. Significance. Existing power supply methods, and, in particular inductive links, comprise stiff and bulky parts. This hinders the development of minimally invasive implantable devices for neuroprostheses based on electrical stimulation. The proposed methodology is intended to relieving such bottleneck. In terms of mass, thinness, and flexibility, the demonstrated implants appear to be unprecedented among the intramuscular stimulation implants ever assayed in vertebrates.

  14. Mass exchange during rectification of multicomponent mixtures of aromatic C/sub 9/ hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Kutsarov, R; Palichev, T; Tasev, Zh

    1978-01-01

    The effectiveness is determined of separating a multicomponent aromatic hydrocarbon (ArU) mixture into binary ones relative to the composition of the initial mixture. The study is conducted in mixtures of ArU which contain: C/sub 8/ ArU, isopropylbenzene, n-propylbenzene, ethyloluene, 1,3,5-trimetylbenzene, 1,2,4-trimethylbenzene, 1,2,3-trimethylbenzene and C/sub 10/ ArU. The total content of the C/sub 8/ and C/sub 10/ ArU is less than 2%. The constants of the phase equilibrium of the components are obtained through experiments or are calculated through the Chao-Sider method. The separation of the multicomponent mixture was conducted in periodic, automated rectification column 30 mm in diameter, filled with a steel spiral with a free volume of 0.818 m/sup 3//m/sup 3/ and a specific surface of 0.785 m/sup 2//m/sup 3/ and an effective headpiece height of 1.5 m. The temperature of the housing was maintained with a precision of 0.5/sup 0/, the speed of vapors was maintained constant (0.231 m/sec) through regulating the pressure differential between the top and bottom with a precision of 0.5 mm of mercury. After reaching a stationary mode, samples of the distillate and the sediment were taken and were analyzed chromatographically with a precision of 0.25%. Five distillations of the multicomponent mixtures of various make up were conducted and the distillates and sediments were analyzed. The obtained data are graphically presented.

  15. PRACTISE – Photo Rectification And ClassificaTIon SoftwarE (V.1.0

    Directory of Open Access Journals (Sweden)

    S. Härer

    2013-06-01

    Full Text Available Terrestrial photography is a cost-effective and easy-to-use method for measuring and monitoring spatially distributed land surface variables. It can be used to continuously investigate remote and often inaccessible terrain. We focus on the observation of snow cover patterns in high mountainous areas. The high temporal and spatial resolution of the photographs have various applications, for example validating spatially distributed snow hydrological models. However, the analysis of a photograph requires a preceding georectification of the digital camera image. To accelerate and simplify the analysis, we have developed the "Photo Rectification And ClassificaTIon SoftwarE" (PRACTISE that is available as a Matlab code. The routine requires a digital camera image, the camera location and its orientation, as well as a digital elevation model (DEM as input. If the viewing orientation and position of the camera are not precisely known, an optional optimisation routine using ground control points (GCPs helps to identify the missing parameters. PRACTISE also calculates a viewshed using the DEM and the camera position. The visible DEM pixels are utilised to georeference the photograph which is subsequently classified. The resulting georeferenced and classified image can be directly compared to other georeferenced data and can be used within any geoinformation system. The Matlab routine was tested using observations of the north-eastern slope of the Schneefernerkopf, Zugspitze, Germany. The results obtained show that PRACTISE is a fast and user-friendly tool, able to derive the microscale variability of snow cover extent in high alpine terrain, but can also easily be adapted to other land surface applications.

  16. Assessment of Autonomic Function by Phase Rectification of RRInterval Histogram Analysis in Chagas Disease

    Directory of Open Access Journals (Sweden)

    Olivassé Nasari Junior

    2015-06-01

    Full Text Available Background: In chronic Chagas disease (ChD, impairment of cardiac autonomic function bears prognostic implications. Phase‑rectification of RR-interval series isolates the sympathetic, acceleration phase (AC and parasympathetic, deceleration phase (DC influences on cardiac autonomic modulation. Objective: This study investigated heart rate variability (HRV as a function of RR-interval to assess autonomic function in healthy and ChD subjects. Methods: Control (n = 20 and ChD (n = 20 groups were studied. All underwent 60-min head-up tilt table test under ECG recording. Histogram of RR-interval series was calculated, with 100 ms class, ranging from 600–1100 ms. In each class, mean RR-intervals (MNN and root-mean-squared difference (RMSNN of consecutive normal RR-intervals that suited a particular class were calculated. Average of all RMSNN values in each class was analyzed as function of MNN, in the whole series (RMSNNT, and in AC (RMSNNAC and DC (RMSNNDC phases. Slopes of linear regression lines were compared between groups using Student t-test. Correlation coefficients were tested before comparisons. RMSNN was log-transformed. (α < 0.05. Results: Correlation coefficient was significant in all regressions (p < 0.05. In the control group, RMSNNT, RMSNNAC, and RMSNNDC significantly increased linearly with MNN (p < 0.05. In ChD, only RMSNNAC showed significant increase as a function of MNN, whereas RMSNNT and RMSNNDC did not. Conclusion: HRV increases in proportion with the RR-interval in healthy subjects. This behavior is lost in ChD, particularly in the DC phase, indicating cardiac vagal incompetence.

  17. Modelling and dynamics of an air separation rectification column as part of an IGCC power plant

    Energy Technology Data Exchange (ETDEWEB)

    Seliger, B.; Hanke-Rauschenbach, R.; Hannemann, F.; Sundmacher, K. [Otto Von Guericke University, Magdeburg (Germany)

    2006-04-15

    An Integrated Gasification Combined Cycle plant (IGCC) opens the well-proven and highly efficient combined cycle process to fossil fuels, like coal or heavy refinery residues. Such a plant thereby possesses a novel linkage of typical energy engineering related units, e.g. a gas turbine and typical process engineering parts, which in the present case is an air separation plant. Different responses from the connected components can cause undesired mass flow fluctuations within the system especially during changing load demands. The cryogenic rectification column, as the core of the air separation plant, strongly affects the system's transient behaviour. The upper part of such a heat-integrated double column, a packed column with structured packing, has therefore been more closely investigated in the present paper. For this purpose, a dynamic model of such a column has been developed which is also able to describe the pressure dynamics supposedly responsible for these mass flow fluctuations. The transient behaviour of the uncontrolled column is analysed and discussed with special regard to pressure dynamics. The column pressure responds to disturbances on two different time scales. The short-term response, which is in the range of 100-200 s, is governed by the transient behaviour of the fluid dynamics and is discussed in detail. The long-term response is dominated by the nonlinear dynamics of the concentration profiles. The time constant of this response depends strongly on the direction and intensity of the disturbance and takes from 10,000 up to several 100,000 s.

  18. Quantum Effects in Nanoantennas and Their Applications in Tunability, Mixing, and Rectification

    KAUST Repository

    Chen, Pai-Yen

    2015-08-04

    It has been recently shown that optical nanoantennas made of single or paired metallic nanoparticles can efficiently couple the propagating light into and from deeply subwavelength volumes. The strong light-matter interaction mediated by surface plasmons in metallic nanostructures allows for localizing optical fields to a subdiffraction-limited region, thereby enhancing emission of nanoemitters and offering the flexible control of nanofocused radiation. Here we theoretically study the nanodipole antennas with submicroscopic gaps, i.e. a few nanometers, for which there exists linear and high-order nonlinear quantum conductivities due to the photon-assisted tunneling effect. Noticeably, these quantum conductivities induced at the nanogap are enhanced by several orders of magnitude, due to the strongly localized optical fields associated with the plasmonic resonance.In this talk, we will show that by tailoring the geometry of nanoantennas and the quantum well structure, a quantum nanodipole antenna with a gap size of few nanometers can induce linear, high-order quantum conductivities that are considerably enhanced by the surface plasmon resonance. We envisage here a number of intriguing nanophotonic applications of these quantum nanoantennas, including (i) modulatable and switchable radiators and metamaterials, with electronic and all-optical tuning (which is related to the two photon absorption), (ii) optical rectification for detection and energy harvesting of infrared and visible light, which are related to the relevant second-order quantum conductivity, (iii) harmonic sensing for the work function and the optical index of nanoparticle, e.g. DNA and molecules, loaded inside the nanogap, and (iv) high harmonic generation and wave mixing with nonlinear quantum conductivities.

  19. S K Date

    Indian Academy of Sciences (India)

    Home; Journals; Bulletin of Materials Science. S K Date. Articles written in Bulletin of Materials Science. Volume 23 Issue 2 April 2000 pp 97-101 Magnetic Materials. Comparison of the irreversible thermomagnetic behaviour of some ferro- and ferrimagnetic systems · P S Anil Kumar P A Joy S K Date · More Details Abstract ...

  20. Dating of cremated bones

    NARCIS (Netherlands)

    Lanting, JN; Aerts-Bijma, AT; van der Plicht, J; Boaretto, E.; Carmi, I.

    2001-01-01

    When dating unburnt bone, bone collagen, the organic fraction of the bone, is used. Collagen does not survive the heat of the cremation pyre, so dating of cremated bone has been considered impossible. Structural carbonate in the mineral fraction of the bone, however, survives the cremation process.

  1. Quaternary dating methods

    International Nuclear Information System (INIS)

    Mahaney, W.C.

    1984-01-01

    The papers in this book cover absolute, relative and multiple dating methods, and have been written by specialists from a number of different earth sciences disciplines - their common interest being the dating of geological materials within the Quaternary. Papers on absolute dating methods discuss radiocarbon, uranium-series, potassium argon, 40 Ar/ 39 Ar, paleomagnetic, obsidian hydration, thermoluminescence, amino acid racemization, tree rings, and lichenometric techniques. Those on relative dating include discussions on various geomorphic relative age indicators such as drainage density changes, hypsometric integrals, bifurcation ratios, stream junction angles, spur morphology, hillslope geometry, and till sheet characteristics. The papers on multiple dating cite examples from the Rocky Mountains, Australia, Lake Agassiz Basin, and the Southern Andes. Also included is the panel discussion which reviews and assesses the information presented, and a field trip guide which discusses the sequences of Wisconian tills and interlayered lacustrine and fluvial sediments. (orig.)

  2. Nonlinear optical rectification in a vertically coupled lens-shaped InAs/GaAs quantum dots with wetting layers under hydrostatic pressure and temperature

    Energy Technology Data Exchange (ETDEWEB)

    Ben Mahrsia, R.; Choubani, M., E-mail: mohsenchoubani3@yahoo.fr; Bouzaiene, L.; Maaref, H.

    2016-06-25

    In this paper we explore the structure parameters, hydrostatic pressure and temperature effects on Nonlinear optical rectification (NOR) in an asymmetric vertically coupled lens-shaped InAs/GaAs quantum dots. During epitaxial growth, lens-shaped quantum dots (QDs) are formed on the wetting layer (WL). Many theoretical works have neglected WL and its effect on nonlinear optical properties of QD-based systems for sake of simplicity. However, in this work the WL has been shown to be so influential in the intersubband energy and nonlinear optical rectification magnitude. Also, a detailed and comprehensive study of the nonlinear optical rectification is theoretical investigated within the framework of the compact density-matrix approach and finite difference method (FDM). It's found that nonlinear optical rectification coefficient is strongly affected not only by the WL, but also by the pressure, temperature and the coupled width between the QDs. Obtained results revealed that a red or a blue shift cane be observed. This behavior in the NOR gives a new degree of freedom in regions of interest for device applications. - Highlights: • Vertically coupled lens-shaped InAs/GaAs quantum dots is investigated. • Photon energy shifts towards the red with increasing pressure. • Photon energy shifts towards the blue with increasing temperature. • Intersubband energy decreases with increasing the wetting layer width. • Nonlinear optical rectification magnitude is controlled and adjusted.

  3. Luminescence dating in archaeology

    International Nuclear Information System (INIS)

    Wintle, A.G.

    2001-01-01

    Thermoluminescence (TL) dating is routinely applied to burnt lithic material. Simple fires are capable of enabling stones weighing a few hundred grams to reach 450 o C, thus zeroing the TL signal. TL dates have been obtained for Upper and Lower Paleolithic sites in Europe and the Near East. TL dating continues to be used for dating pottery and for authentification of ceramic works of art. Some recent studies report the use of optically stimulated luminescence (OSL) (also know as photoluminescence) for dating very small samples of quartz, e.g. from small pieces of pottery or frm metallurgical slag The major recent advance has been in the development of a reliable laboratory procedure for using the OSL signal from quartz to obtain the past radiation exposure. The quartz OSL signal is extremely sensitive to light and is reduced to a negligible level on exposure to direct sunlight for radionuclides during burial, signal to date san.sized quartz grains extracted from sediments, The OSL signal is stimulated by 470 nm light from emitting diodes and the detected using flirters centred on 340 nm A similar signal can be obtained from feldspar grain when are exposed to infrared wavelengths around 880 nm. The infrared stimulated luminescence (IRSL) signals is also rapidly depleted by exposure to sunlight, and dating of colluvial deposits from archaeological sites has been reported

  4. Conduction and rectification in NbO{sub x}- and NiO-based metal-insulator-metal diodes

    Energy Technology Data Exchange (ETDEWEB)

    Osgood, Richard M., E-mail: richard.m.osgood.civ@mail.mil; Giardini, Stephen; Carlson, Joel [US Army Natick Soldier Research Development and Engineering Center (NSRDEC), 15 General Greene Ave., Natick, Massachusetts 01760 (United States); Periasamy, Prakash; Guthrey, Harvey; O' Hayre, Ryan [Department of Metallurgical and Materials Engineering, Colorado School of Mines, Golden, Colorado 80401 (United States); Chin, Matthew; Nichols, Barbara; Dubey, Madan [RF and Electronics Division, US Army Research Laboratory, Adelphi, Maryland 20783 (United States); Fernandes, Gustavo; Kim, Jin Ho; Xu, Jimmy [Division of Engineering, Brown University, Box D, Providence, Rhode Island 02912 (United States); Parilla, Philip; Berry, Joseph; Ginley, David [National Renewable Energy Laboratory, Golden, Colorado 80401 (United States)

    2016-09-15

    Conduction and rectification in nanoantenna-coupled NbO{sub x}- and NiO-based metal-insulator-metal (MIM) diodes (“nanorectennas”) are studied by comparing new theoretical predictions with the measured response of nanorectenna arrays. A new quantum mechanical model is reported and agrees with measurements of current–voltage (I–V) curves, over 10 orders of magnitude in current density, from [NbO{sub x}(native)-Nb{sub 2}O{sub 5}]- and NiO-based samples with oxide thicknesses in the range of 5–36 nm. The model, which introduces new physics and features, including temperature, electron effective mass, and image potential effects using the pseudobarrier technique, improves upon widely used earlier models, calculates the MIM diode's I–V curve, and predicts quantitatively the rectification responsivity of high frequency voltages generated in a coupled nanoantenna array by visible/near-infrared light. The model applies both at the higher frequencies, when high-energy photons are incident, and at lower frequencies, when the formula for classical rectification, involving derivatives of the I–V curve, may be used. The rectified low-frequency direct current is well-predicted in this work's model, but not by fitting the experimentally measured I–V curve with a polynomial or by using the older Simmons model (as shown herein). By fitting the measured I–V curves with our model, the barrier heights in Nb-(NbO{sub x}(native)-Nb{sub 2}O{sub 5})-Pt and Ni-NiO-Ti/Ag diodes are found to be 0.41/0.77 and 0.38/0.39 eV, respectively, similar to literature reports, but with effective mass much lower than the free space value. The NbO{sub x} (native)-Nb{sub 2}O{sub 5} dielectric properties improve, and the effective Pt-Nb{sub 2}O{sub 5} barrier height increases as the oxide thickness increases. An observation of direct current of ∼4 nA for normally incident, focused 514 nm continuous wave laser beams are reported, similar in magnitude to recent reports

  5. Date Rape (For Teens)

    Science.gov (United States)

    ... owe" someone sex, even if you're a couple. Rape is not always violent. If you say " ... date rape" drugs like: rohypnol , called roofies, lunch money, or mind erasers GHB (gamma hydroxybutyric acid), called ...

  6. Methods of dating

    Energy Technology Data Exchange (ETDEWEB)

    Gatty, B

    1986-04-01

    Scientific methods of dating, born less than thirty years ago, have recently improved tremendously. First the dating principles will be given; then it will be explained how, through natural radioactivity, we can have access to the age of an event or an object; the case of radiocarbon will be especially emphasized. The principle of relative methods such as thermoluminescence or paleomagnetism will also be shortly given. What is the use for dating. The fields of its application are numerous; through these methods, relatively precise ages can be given to the major events which have been keys in the history of universe, life and man; thus, dating is a useful scientific tool in astrophysics, geology, biology, anthropology and archeology. Even if certain ages are still subject to controversies, we can say that these methods have confirmed evolution's continuity, be it on a cosmic, biologic or human scale, where ages are measured in billions, millions or thousands of years respectively.

  7. Radiometric dating methods

    International Nuclear Information System (INIS)

    Bourdon, B.

    2003-01-01

    The general principle of isotope dating methods is based on the presence of radioactive isotopes in the geologic or archaeological object to be dated. The decay with time of these isotopes is used to determine the 'zero' time corresponding to the event to be dated. This paper recalls the general principle of isotope dating methods (bases, analytical methods, validation of results and uncertainties) and presents the methods based on natural radioactivity (Rb-Sr, Sm-Nd, U-Pb, Re-Os, K-Ar (Ar-Ar), U-Th-Ra- 210 Pb, U-Pa, 14 C, 36 Cl, 10 Be) and the methods based on artificial radioactivity with their applications. Finally, the methods based on irradiation damages (thermoluminescence, fission tracks, electron spin resonance) are briefly evoked. (J.S.)

  8. NAIP 2012 Image Dates

    Data.gov (United States)

    Farm Service Agency, Department of Agriculture — This map is produced by the Aerial Phtography Field Office (APFO) to show the image acquisition dates for the 2012 National Agriculture Imagery Program (NAIP)...

  9. NAIP 2014 Image Dates

    Data.gov (United States)

    Farm Service Agency, Department of Agriculture — This map is produced by the Aerial Phtography Field Office (APFO) to show the image acquisition dates for the 2014 National Agriculture Imagery Program (NAIP)...

  10. Food Product Dating

    Science.gov (United States)

    ... Standard Forms FSIS United States Department of Agriculture Food Safety and Inspection Service About FSIS District Offices ... Web Content Viewer (JSR 286) Actions ${title} Loading... Food Product Dating "Best if Used By" is a ...

  11. NAIP 2013 Image Dates

    Data.gov (United States)

    Farm Service Agency, Department of Agriculture — This map is produced by the Aerial Phtography Field Office (APFO) to show the image acquisition dates for the 2013 National Agriculture Imagery Program (NAIP)...

  12. NAIP 2011 Image Dates

    Data.gov (United States)

    Farm Service Agency, Department of Agriculture — This map is produced by the Aerial Phtography Field Office (APFO) to show the image acquisition dates for the 2011 National Agriculture Imagery Program (NAIP)...

  13. Dating fossil opal phytoliths

    International Nuclear Information System (INIS)

    Lentfer, C.; Boyd, B.; Torrence, R.

    1999-01-01

    Full text: Opal phytoliths are microscopic silica bodies formed by the precipitation of hydrated silica dioxide (SiO 2 nH 2 0) in, around and between cell walls. They are relatively resistant to degradation in most environments and thus, can occur in large quantities in palaeosediments. Consequently, they are valuable tools for environmental reconstruction. Furthermore, phytoliths are often the only recoverable organic material in well oxidised sediments, the occluded carbon provides the opportunity for dating sediment whose ages have previously been difficult to determine, and thus, increase the potential for fine resolution determination of environmental change. This poster describes the results of an investigation assessing the viability of AMS radiocarbon dating of fossil phytolith inclusions using samples from Garua Island, West New Britain, PNG. Thirteen phytolith samples, isolated from sediments previously dated using tephrastratigraphy and C14 dating of macroremains of nutshells and wood charcoal, were used in the analysis. As a control measure, thirteen parallel samples of microscopic charcoal were also dated using AMS. The results show that the AMS dates for the microscopic charcoal samples are consistent with ages anticipated from the other dating methods, for all but one sample. However, the dates for eight of the thirteen phytolith samples are considerably younger than expected. This bias could be explained by several factors, including downwashing of phytolith through soils, bioturbation, carbon exchange through the siliceous matrix of the phytolith bodies, and contamination from extraneous sources of modern carbon retained in the samples. Research is currently focusing on the investigation of these issues and selected samples are in the process of being retreated with strong oxidising agents to clear contaminants prior to re-dating. Further to this, a full investigation of one profile with a long sequence is underway. High concentrations of

  14. Rigorous Line-Based Transformation Model Using the Generalized Point Strategy for the Rectification of High Resolution Satellite Imagery

    Directory of Open Access Journals (Sweden)

    Kun Hu

    2016-09-01

    Full Text Available High precision geometric rectification of High Resolution Satellite Imagery (HRSI is the basis of digital mapping and Three-Dimensional (3D modeling. Taking advantage of line features as basic geometric control conditions instead of control points, the Line-Based Transformation Model (LBTM provides a practical and efficient way of image rectification. It is competent to build the mathematical relationship between image space and the corresponding object space accurately, while it reduces the workloads of ground control and feature recognition dramatically. Based on generalization and the analysis of existing LBTMs, a novel rigorous LBTM is proposed in this paper, which can further eliminate the geometric deformation caused by sensor inclination and terrain variation. This improved nonlinear LBTM is constructed based on a generalized point strategy and resolved by least squares overall adjustment. Geo-positioning accuracy experiments with IKONOS, GeoEye-1 and ZiYuan-3 satellite imagery are performed to compare rigorous LBTM with other relevant line-based and point-based transformation models. Both theoretic analysis and experimental results demonstrate that the rigorous LBTM is more accurate and reliable without adding extra ground control. The geo-positioning accuracy of satellite imagery rectified by rigorous LBTM can reach about one pixel with eight control lines and can be further improved by optimizing the horizontal and vertical distribution of control lines.

  15. Nonlinear optical rectification and second and third harmonic generation in GaAs δ-FET systems under hydrostatic pressure

    International Nuclear Information System (INIS)

    Martínez-Orozco, J.C.; Mora-Ramos, M.E.; Duque, C.A.

    2012-01-01

    The GaAs n-type delta-doped field effect transistor is proposed as a source for nonlinear optical responses such as second order rectification and second and third harmonic generation. Particular attention is paid to the effect of hydrostatic pressure on these properties, related with the pressure-induced modifications of the energy level spectrum. The description of the one-dimensional potential profile is made including Hartree and exchange and correlation effects via a Thomas–Fermi-based local density approximation. The allowed energy levels are calculated within the effective mass and envelope function approximations by means of an expansion over an orthogonal set of infinite well eigenfunctions. The results for the coefficients of nonlinear optical rectification and second and third harmonic generation are reported for several values of the hydrostatic pressure. - Highlights: ► GaAs n-type delta-doped field effect transistor. ► NOR and SHG are enhanced as a result of the pressure. ► THG is quenched as a result of the pressure. ► The zero pressure situation is the best scenario for the THG.

  16. Nonlinear optical rectification in vertically coupled InAs/GaAs quantum dots under electromagnetic fields, pressure and temperature effects

    Energy Technology Data Exchange (ETDEWEB)

    Choubani, M., E-mail: mohsenchoubani3@yahoo.fr; Ben Mahrsia, R.; Bouzaiene, L.; Maaref, H.

    2013-12-15

    In this paper we explore the effects of the structural dimensions, applied electromagnetic fields, hydrostatic pressure and temperature on the nonlinear optical rectification (NOR) in Vertically Coupled InAs/GaAs Quantum Dots (VCQDs). The analytical expression of the NOR is analyzed by using the density matrix formalism, the effective mass and the Finite Difference Method (FDM). Obtained results show that the NOR obtained with this coupled system is not a monotonic function of the barrier width, electromagnetic fields, pressure and temperature. Also, calculated results reveal that the resonant peaks of the NOR can be blue-shifted or red-shifted energies depending on the energy of the lowest confined states in the VCQDs structure. In addition, this condition can be controlled by changes in the structural dimensions and the external proofs mentioned above. -- Highlights: • In this paper we explore the effects of the barrier width, applied electromagnetic fields, hydrostatic pressure and temperature on the nonlinear optical rectification (NOR) in Vertically Coupled InAs/GaAs Quantum Dots (VCQDs). • The calculated results reveal that the resonant peaks of the NOR can be blue-shifted to large photon energies or red-shifted to lower photon energies. • In this paper, all parameters: electromagnetic fields, pressure and temperature effects are introduced and investigated. • The resonant energy and the magnitude of the NOR are controlled and adjusted.

  17. History of radiocarbon dating

    Energy Technology Data Exchange (ETDEWEB)

    Libby, W F [Department of Chemistry and Institute of Geophysics, University of California, Los Angeles, CA (United States)

    1967-08-15

    The development is traced of radiocarbon dating from its birth in curiosity regarding the effects of cosmic radiation on Earth. Discussed in historical perspective are: the significance of the initial measurements in determining the course of developments; the advent of the low-level counting technique; attempts to avoid low-level counting by the use of isotopic enrichment; the gradual appearance of the environmental effect due to the combustion of fossil fuel (Suess effect); recognition of the atmosphere ocean barrier for carbon dioxide exchange; detailed understanding of the mixing mechanism from the study of fallout radiocarbon; determination of the new half-life; indexing and the assimilation problem for the massive accumulation of dates; and the proliferation of measurement techniques and the impact of archaeological insight on the validity of radiocarbon dates. (author)

  18. Obsidian dating prospects

    International Nuclear Information System (INIS)

    Ambrose, W.

    1997-01-01

    Full text: Developments in the nuclear industry have shown that some of the problems related to the glassification of waste for long term storage are centred on the rate of glass weathering in various repositories. Long term weathering of artificial glasses is paralleled by the archaeological problem of determining hydration rates in obsidian artefacts as a means of dating their manufacture. Figures available for sites in Papua New Guinea indicate that the weathering rate is sufficiently fast to render conventional hydration measurement completely unreliable. This follows from the range of calculated surface reduction rates which range between .0002μ to .004μ per year depending on the site's location and the obsidian source. Hydration rates for key Papua New Guinea obsidians have been determined from long term experimental laboratory exposure and these are used to evaluate the age of obsidians from selected archaeological sites. By adopting a strategy of measuring hydration in concealed fissures both the weathering rate and the dating of the Papua New Guinea obsidians have been successfully achieved. The dissolution rates of natural obsidians could be useful in considering weathering rates for artificial glasses. An improved system for calculating the annual effective hydration temperature is presented which gives a better control of micro-environmental temperature in its crucial rate determining role. The combined result of these developments gives obsidian hydration dating an enhanced capacity to be a useful and independent dating system

  19. Confronting Dating Violence.

    Science.gov (United States)

    McNulty, Raymond J.; Heller, Daniel A.; Binet, Tracy

    1997-01-01

    To be safe havens for children, schools cannot address the intellect only. Brattleboro (Vermont) Union High School went beyond academics by sponsoring a performance of "The Yellow Dress," a powerful one-woman play about a teenage victim of dating violence. The production challenged participants to unite school and community, intellect…

  20. The Realities of Date Rape.

    Science.gov (United States)

    Presley, Cara; Watson, Jennifer; Williams, Audrey R.

    This poster presentation addresses the issue of date rape, specifically in the college environment. Highlighted are date rape statistics, demographics, and date rape drugs. Also discussed are date rape warnings and prevention strategies. It is concluded that college and university administrators must place the issue of date rape and acquaintance…

  1. The TL dating of ancient porcelain

    International Nuclear Information System (INIS)

    Leung, P.L.; Stokes, M.J.; Wang Weida; Xia Junding; Zhou Zhixin

    1997-01-01

    The age determination of ancient porcelain using the pre-dose technique in TL dating was reported. The variation of beta dose with depth below the surface of the porcelain slice, the thermal activation characteristic (TAC) for 110 degree C peak, the measurement of paleodose and the estimation of annual dose were studied. The results show that this technique is suitable for authenticity testing of ancient porcelain, but both accuracy and precision for porcelain dating are worse than those for pottery, because porcelain differs from pottery on composition, structure and firing temperature. Besides, some complicated factors in the pre-dose technique would be the possible cause of the greater errors

  2. Thermoluminescence dating of pottery

    International Nuclear Information System (INIS)

    Higashimura, Takenobu; Ichikawa, Yoneta.

    1978-01-01

    This report is divided into two parts. The first half describes on the history of thermoluminescence dating, and the latter half, the principle and measurement examples. It was in late 1955 that the measurement of radiation dose using thermoluminescence began. The method to thermoluminescence dating was developed when it was found that most natural stones emit the thermoluminescence. About Greek earthen wares, the study of which was presented in 1961 by G. Kennedy of University of California, the dating was able to be made within the standard deviation of 10%. Since then, this dating method progressed rapidly, and a number of laboratories are now forwarding the investigation. In the samples of natural materials, intensity of thermoluminescence I is proportional to natural radiation dose D which has been absorbed by the samples, i.e. I = kD, where k is the susceptibility of thermoluminescence of the samples. Since k is different in each sample, D can be determined by irradiating the sample with β or γ ray of known dose D 0 , measuring its luminescence I 0 , and eliminating k through these two equations, because i 0 = kD 0 . Next, if t is assumed to be the time passed since a pottery was made, D is expressed as Rt, where R is the natural radiation dose per year absorbed by the pottery. Thus t is determined if R is known. The report describes on the method of measuring R. As an example, the results of measurement of the potteries excavated at Iwakura remains, Yorikura, Taishaku-kyo, are listed. Results by 14 C dating are also described for reference. (Wakatsuki, Y.)

  3. Sequential Vapor Infiltration Treatment Enhances the Ionic Current Rectification Performance of Composite Membranes Based on Mesoporous Silica Confined in Anodic Alumina.

    Science.gov (United States)

    Liang, Yanyan; Liu, Zhengping

    2016-12-20

    Ionic current rectification of nanofluidic diode membranes has been studied widely in recent years because it is analogous to the functionality of biological ion channels in principle. We report a new method to fabricate ionic current rectification membranes based on mesoporous silica confined in anodic aluminum oxide (AAO) membranes. Two types of mesostructured silica nanocomposites, hexagonal structure and nanoparticle stacked structure, were used to asymmetrically fill nanochannels of AAO membranes by a vapor-phase synthesis (VPS) method with aspiration approach and were further modified via sequence vapor infiltration (SVI) treatment. The ionic current measurements indicated that SVI treatment can modulate the asymmetric ionic transport in prepared membranes, which exhibited clear ionic current rectification phenomenon under optimal conditions. The ionic current rectifying behavior is derived from the asymmetry of surface conformations, silica species components, and hydrophobic wettability, which are created by the asymmetrical filling type, silica depositions on the heterogeneous membranes, and the condensation of silanol groups. This article provides a considerable strategy to fabricate composite membranes with obvious ionic current rectification performance via the cooperation of the VPS method and SVI treatment and opens up the potential of mesoporous silica confined in AAO membranes to mimic fluid transport in biological processes.

  4. Direct and indirect dating of gypsum occurrences in deserts using luminescence methods

    International Nuclear Information System (INIS)

    Nagar, Y.C.; Juyal, N.; Singhyi, A.K.; Kocurek, G.; Wadhawan, S.K.

    2005-01-01

    In the present study we have made an attempt to directly date gypsum or provide indirect age estimate for gypsum formation through dating the associated sediments (quartz) using the luminescence dating technique. In the direct dating of gypsum, we explored the Optically Stimulated Luminescence (OSL) and Thermally Stimulated Luminescence (TL) behaviour of gypsum. The associated sediments (indirect dating) were dated using the traces of quartz extract from gypsum (concentration 0.1% ) and the underlying and overlying quartz sand in playa

  5. Amino acid racemisation dating

    International Nuclear Information System (INIS)

    Murray-Wallace, C.V.

    1999-01-01

    The potential of the time-dependent amino acid racemisation reaction as a method of age assessment was first reported by Hare and Abelson (1968). They noted that in specimens of the bivalve mollusc Mercenaria sp., greater concentrations of amino acids in the D-configuration with increasing fossil age. Hare and Abelson (1968) also reported negligible racemisation in a modern specimen of Mecanaria sp. On this basis they suggested that the extent of amino acid racemisation (epimerisation in the case of isoleucine) may be used to assess the age of materials within and beyond the range of radiocarbon dating. For the past thirty years amino acid racemisation has been extensively applied in Quaternary research as a method of relative and numeric dating, and a particularly large literature has emerged on the subject

  6. Dating fractures in infants

    Energy Technology Data Exchange (ETDEWEB)

    Halliday, K.E., E-mail: kath.halliday@nuh.nhs.uk [Department of Radiology, Nottingham University Hospitals, Queen' s Medical Centre, Nottingham (United Kingdom); Broderick, N J; Somers, J M [Department of Radiology, Nottingham University Hospitals, Queen' s Medical Centre, Nottingham (United Kingdom); Hawkes, R [Department of Radiology, Paul O' Gorman Building, Bristol (United Kingdom)

    2011-11-15

    Aim: To document the timing of the appearance of the radiological features of fracture healing in a group of infants in which the date of injury was known and to assess the degree of interobserver agreement. Materials and methods: Three paediatric radiologists independently assessed 161 images of 37 long bone fractures in 31 patients aged 0-44 months. The following features were assessed: soft-tissue swelling, subperiosteal new bone formation (SPNBF), definition of fracture line, presence or absence of callus, whether callus was well or ill defined, and the presence of endosteal callus. Results: Agreement between observers was only moderate for all discriminators except SPNBF. SPNBF was invariably seen after 11 days but was uncommon before this time even in the very young. In one case SPNBF was seen at 4 days. Conclusion: With the exception of SPNBF, the criteria relied on to date fractures are either not reproducible or are poor discriminators of fracture age.

  7. Dating fractures in infants

    International Nuclear Information System (INIS)

    Halliday, K.E.; Broderick, N.J.; Somers, J.M.; Hawkes, R.

    2011-01-01

    Aim: To document the timing of the appearance of the radiological features of fracture healing in a group of infants in which the date of injury was known and to assess the degree of interobserver agreement. Materials and methods: Three paediatric radiologists independently assessed 161 images of 37 long bone fractures in 31 patients aged 0-44 months. The following features were assessed: soft-tissue swelling, subperiosteal new bone formation (SPNBF), definition of fracture line, presence or absence of callus, whether callus was well or ill defined, and the presence of endosteal callus. Results: Agreement between observers was only moderate for all discriminators except SPNBF. SPNBF was invariably seen after 11 days but was uncommon before this time even in the very young. In one case SPNBF was seen at 4 days. Conclusion: With the exception of SPNBF, the criteria relied on to date fractures are either not reproducible or are poor discriminators of fracture age.

  8. Thermoluminescence dating method

    International Nuclear Information System (INIS)

    Zink, A.

    2004-01-01

    A crystal that is submitted to radiation stores energy and releases this energy under the form of light whenever it is heated. These 2 properties: the ability to store energy and the ability to reset the energy stored are the pillars on which time dating methods like thermoluminescence are based. A typical accuracy of the thermoluminescence method is between 5 to 7% but an accuracy of 3% can be reached with a sufficient number of measurement. This article describes the application of thermoluminescence to the dating of a series of old terra-cotta statues. This time measurement is absolute and does not require any calibration, it represents the time elapsed since the last heating of the artifact. (A.C.)

  9. Radiocarbon dating for contributors

    International Nuclear Information System (INIS)

    Jansen, H.S.

    1984-06-01

    This report describes the radiocarbon facility at the Institute of Nuclear Sciences, and is written for potential contributors, current users, and for those who advise others. The report briefly outlines the principles and practices of C-14 dating; with emphasis on factors that enable contributors to judge whether C-14 work is appropriate, and to assist them with the procedures to be followed in order to get the best results. Age determinations, being the main requirements by contributors, have been discussed in detail

  10. Broken space-time symmetries and mechanisms of rectification of ac fields by nonlinear (non)adiabatic response

    DEFF Research Database (Denmark)

    Denisov, S.; Flach, S.; Ovchinnikov, A. A.

    2002-01-01

    We consider low-dimensional dynamical systems exposed to a heat bath and to additional ac fields. The presence of these ac fields may lead to a breaking of certain spatial or temporal symmetries, which in turn cause nonzero averages of relevant observables. Nonlinear (non)adiabatic response is em...... is employed to explain the effect. We consider a case of a particle in a periodic potential as an example and discuss the relevant symmetry breakings and the mechanisms of rectification of the current in such a system.......We consider low-dimensional dynamical systems exposed to a heat bath and to additional ac fields. The presence of these ac fields may lead to a breaking of certain spatial or temporal symmetries, which in turn cause nonzero averages of relevant observables. Nonlinear (non)adiabatic response...

  11. Optimal Design of Rectification Circuit in Electronic Circuit Fault Self-repair Based on EHW and RBT

    Institute of Scientific and Technical Information of China (English)

    ZHANG Junbin; CAI Jinyan; MENG Yafeng

    2018-01-01

    Reliability of traditional electronic circuit is improved mainly by redundant fault-tolerant technol-ogy with large hardware resource consumption and limited fault self-repair capability. In complicated environment, electronic circuit faults appear easily. If on-site immedi-ate repair is not implemented, normal running of elec-tronic system will be directly affected. In order to solve these problems, Evolvable hardware (EHW) technology is widely used. The conventional EHW has some bottlenecks. The optimal design of Rectification circuit (RTC) is fur-ther researched on the basis of the previously proposed fault self-repair based on EHW and Reparation balance technology (RBT). Fault sets are selected by fault danger degree and fault coverage rate. The optimal designed RTC can completely repair faults in the fault set. Simulation re-sults prove that it has higher self-repair capability and less hardware resource.

  12. Rectification properties of n-type nanocrystalline diamond heterojunctions to p-type silicon carbide at high temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Goto, Masaki; Amano, Ryo; Shimoda, Naotaka [Graduate School of Automotive Science, Kyushu University, Nishiku, Fukuoka 819-0395 (Japan); Kato, Yoshimine, E-mail: yoshimine.kato@zaiko.kyushu-u.ac.jp [Department of Materials Science and Engineering, Kyushu University, Nishiku, Fukuoka 819-0395 (Japan); Teii, Kungen [Department of Applied Science for Electronics and Materials, Kyushu University, Kasuga, Fukuoka 816-8580 (Japan)

    2014-04-14

    Highly rectifying heterojunctions of n-type nanocrystalline diamond (NCD) films to p-type 4H-SiC substrates are fabricated to develop p-n junction diodes operable at high temperatures. In reverse bias condition, a potential barrier for holes at the interface prevents the injection of reverse leakage current from the NCD into the SiC and achieves the high rectification ratios of the order of 10{sup 7} at room temperature and 10{sup 4} even at 570 K. The mechanism of the forward current injection is described with the upward shift of the defect energy levels in the NCD to the conduction band of the SiC by forward biasing. The forward current shows different behavior from typical SiC Schottky diodes at high temperatures.

  13. Sediment dating in review

    International Nuclear Information System (INIS)

    Prescott, J.R.; Robertson, G.B.

    1997-01-01

    The paper will comment on a few issues of particular relevance to Australasia. Thermoluminescent (TL) methods applied to open sites have been demonstrated to be effective. A particularly good example of this is to be found in the South East of South Australia, where a sequence of low ranges runs roughly parallel with the coast. They represent relict sand dunes left behind, on a slowly rising land surface by successive interglacial incursions of the sea at roughly 120 ka intervals. Comparison with ages established on independent geological grounds allows a test of quartz TL and IRSL ages that is believable back to 500 ka. Older than this, we do not yet understand the physics of the quartz well enough to go unequivocally forward (backward?). Similar results are emerging elsewhere. With dating limits being pushed ever further back, the time variation of the environmental radiation giving rise to the stored luminescent energy needs to be addressed. Particularly at wet sites, radioactive disequilibrium must be considered. In any case, a time profile of the radiation dose rate needs to be determined.In dating a given site or sites the value of ages obtained by any dating method,including C-14, is enhanced by parallel measurements with an different method

  14. Micro rectennas: Brownian ratchets for thermal-energy harvesting

    International Nuclear Information System (INIS)

    Pan, Y.; Powell, C. V.; Balocco, C.; Song, A. M.

    2014-01-01

    We experimentally demonstrated the operation of a rectenna for harvesting thermal (blackbody) radiation and converting it into dc electric power. The device integrates an ultrafast rectifier, the self-switching nanodiode, with a wideband log-periodic spiral microantenna. The radiation from the thermal source drives the rectenna out of thermal equilibrium, permitting the rectification of the excess thermal fluctuations from the antenna. The power conversion efficiency increases with the source temperatures up to 0.02% at 973 K. The low efficiency is attributed mainly to the impedance mismatch between antenna and rectifier, and partially to the large field of view of the antenna. Our device not only opens a potential solution for harvesting thermal energy but also provides a platform for experimenting with Brownian ratchets

  15. Micro rectennas: Brownian ratchets for thermal-energy harvesting

    Science.gov (United States)

    Pan, Y.; Powell, C. V.; Song, A. M.; Balocco, C.

    2014-12-01

    We experimentally demonstrated the operation of a rectenna for harvesting thermal (blackbody) radiation and converting it into dc electric power. The device integrates an ultrafast rectifier, the self-switching nanodiode, with a wideband log-periodic spiral microantenna. The radiation from the thermal source drives the rectenna out of thermal equilibrium, permitting the rectification of the excess thermal fluctuations from the antenna. The power conversion efficiency increases with the source temperatures up to 0.02% at 973 K. The low efficiency is attributed mainly to the impedance mismatch between antenna and rectifier, and partially to the large field of view of the antenna. Our device not only opens a potential solution for harvesting thermal energy but also provides a platform for experimenting with Brownian ratchets.

  16. Micro rectennas: Brownian ratchets for thermal-energy harvesting

    Energy Technology Data Exchange (ETDEWEB)

    Pan, Y.; Powell, C. V.; Balocco, C., E-mail: claudio.balocco@durham.ac.uk [School of Engineering and Computing Sciences, Durham University, Durham DH1 3LE (United Kingdom); Song, A. M. [School of Electrical and Electronic Engineering, University of Manchester, Manchester M13 9PL (United Kingdom)

    2014-12-22

    We experimentally demonstrated the operation of a rectenna for harvesting thermal (blackbody) radiation and converting it into dc electric power. The device integrates an ultrafast rectifier, the self-switching nanodiode, with a wideband log-periodic spiral microantenna. The radiation from the thermal source drives the rectenna out of thermal equilibrium, permitting the rectification of the excess thermal fluctuations from the antenna. The power conversion efficiency increases with the source temperatures up to 0.02% at 973 K. The low efficiency is attributed mainly to the impedance mismatch between antenna and rectifier, and partially to the large field of view of the antenna. Our device not only opens a potential solution for harvesting thermal energy but also provides a platform for experimenting with Brownian ratchets.

  17. Rectification of the water permeability in COS-7 cells at 22, 10 and 0°C.

    Directory of Open Access Journals (Sweden)

    Diana B Peckys

    Full Text Available The osmotic and permeability parameters of a cell membrane are essential physico-chemical properties of a cell and particularly important with respect to cell volume changes and the regulation thereof. Here, we report the hydraulic conductivity, L(p, the non-osmotic volume, V(b, and the Arrhenius activation energy, E(a, of mammalian COS-7 cells. The ratio of V(b to the isotonic cell volume, V(c iso, was 0.29. E(a, the activation energy required for the permeation of water through the cell membrane, was 10,700, and 12,000 cal/mol under hyper- and hypotonic conditions, respectively. Average values for L(p were calculated from swell/shrink curves by using an integrated equation for L(p. The curves represented the volume changes of 358 individually measured cells, placed into solutions of nonpermeating solutes of 157 or 602 mOsm/kg (at 0, 10 or 22°C and imaged over time. L(p estimates for all six combinations of osmolality and temperature were calculated, resulting in values of 0.11, 0.21, and 0.10 µm/min/atm for exosmotic flow and 0.79, 1.73 and 1.87 µm/min/atm for endosmotic flow (at 0, 10 and 22°C, respectively. The unexpected finding of several fold higher L(p values for endosmotic flow indicates highly asymmetric membrane permeability for water in COS-7. This phenomenon is known as rectification and has mainly been reported for plant cell, but only rarely for animal cells. Although the mechanism underlying the strong rectification found in COS-7 cells is yet unknown, it is a phenomenon of biological interest and has important practical consequences, for instance, in the development of optimal cryopreservation.

  18. Interannual Variability In the Atmospheric CO2 Rectification Over Boreal Forests Based On A Coupled Ecosystem-Atmosphere Model

    Science.gov (United States)

    Chen, B.; Chen, J. M.; Worthy, D.

    2004-05-01

    Ecosystem CO2 exchange and the planetary boundary layer (PBL) are correlated diurnally and seasonally. The simulation of this atmospheric rectifier effect is important in understanding the global CO2 distribution pattern. A 12-year (1990-1996, 1999-2003), continuous CO2 measurement record from Fraserdale, Ontario (located ~150 km north of Timmons), along with a coupled Vertical Diffusion Scheme (VDS) and ecosystem model (Boreal Ecosystem Productivity Simulator, BEPS), is used to investigate the interannual variability in this effect over a boreal forest region. The coupled model performed well in simulating CO2 vertical diffusion processes. Simulated annual atmospheric rectifier effects, (including seasonal and diurnal), quantified as the variation in the mean CO2 concentration from the surface to the top of the PBL, varied from 2.8 to 4.1 ppm, even though the modeled seasonal variations in the PBL depth were similar throughout the 12-year period. The differences in the interannual rectifier effect primarily resulted from changes in the biospheric CO2 uptake and heterotrophic respiration. Correlations in the year-to year variations of the CO2 rectification were found with mean annual air temperatures, simulated gross primary productivity (GPP) and heterotrophic respiration (Rh) (r2=0.5, 0.46, 0.42, respectively). A small increasing trend in the CO2 rectification was also observed. The year-to-year variation in the vertical distribution of the monthly mean CO2 mixing ratios (reflecting differences in the diurnal rectifier effect) was related to interannual climate variability, however, the seasonal rectifier effects were found to be more sensitive to climate variability than the diurnal rectifier effects.

  19. Optical rectification through an Al 2 O 3 based MIM passive rectenna at 28.3 THz

    KAUST Repository

    Jayaswal, Gaurav

    2017-11-21

    Harevesting energy from waste heat which fluctuates between, approximately, 250 K and 1500 K, i.e., peaking at 2–11 μm, could be a game changer in terms of tapping on to renewable energy sources. However, research in this area has remained elusive due to numerous challenges. We consider waste heat to be an electromagnetic (EM) wave in the mid infrared (IR) frequency range, which can be captured through a resonant antenna and rectified into useful DC through a diode, an arrangement typically known as a rectenna. A bowtie antenna has been optimized for IR field capture and enhancement through EM simulations. At the overlap of the bowtie arms, a metal-insulator-metal (MIM) diode has been realized that can operate at such a high frequency (28.3 THz or 10.6 μm). The choice of a low permittivity insulator (Al2O3) helps metigate the RC time constant and the diode\\'s cutoff frequency, whereas the two different work function metals, Au and Ti, facilitate diode operation through tunneling at no applied bias. A custom optical characterization setup employing a 10.6 μm CO2 laser has been used to assess the IR capture and rectification ability of the rectenna device. A polarization dependent voltage output which is well above the noise level and well matched with our calculations, confirms the successful rectenna operation. According to authors\\' best knowledge, this is the first demonstration of rectification at 28.3 THz through a MIM diode based rectenna at zero applied bias.

  20. Dating Violence among College Students

    Science.gov (United States)

    Iconis, Rosemary

    2013-01-01

    Dating violence is a significant problem on college campuses. More than one-fifth of the undergraduate dating population are physically abused by their dating partners and an even greater percentage are psychologically abused. Researchers have identified risk factors for college student dating violence. Preventive interventions are strongly…

  1. Flirting in Online Dating

    DEFF Research Database (Denmark)

    Mortensen, Kristine Køhler

    2017-01-01

    Various fields have examined the activity of flirting, predominantly based on experimental and reported data; the interactional workings are therefore often overlooked. Based on emails and chats from two Danish online dating sites, this article investigates how users negotiate romantic connections...... through the flirting strategy of ‘imagined togetherness’, linguistically constructing imagery of a shared future. Using the notion of the chronotope, turn-by-turn analysis demonstrates how users, embedded in the activity of getting to know each other, tenuously communicate romantic interest by alluding...

  2. Bomb pulse radiocarbon dating

    International Nuclear Information System (INIS)

    Tuniz, C.; Zoppi, U.; Hotchkis, M.A.C.

    2004-01-01

    Modern forensic science has to deal not only with homicides and other traditional crimes but also with more global threats such as the smuggling of nuclear materials, clandestine production of weapons of mass destruction, stockpiling of illicit drugs by state controlled groups and war crimes. Forensic applications have always benefited from the use of advanced analytical tools that can characterize materials found at crime scenes. In this paper we will discuss the use of accelerator mass spectrometry (AMS) as an ultrasensitive tool for the crime laboratories of the third millennium. An important objective in forensic science is to order past events chronologically by analysing materials associated with criminal actions. Radiocarbon dating is known to the general public for its application to historical and prehistorical investigations. Examples of forensic significance include the assassination of the Inca Atahualpa by Francisco Pizarro in the early 1530s, the possible murder of the Tyrolean Ice Man (Oetzi) 5300 years ago and the analysis of the burial cloths allegedly associated with the crucifixion of Jesus Christ . Recent murders, including those associated with war crimes in the Balkans during the 1990s, can be studied using 14 C bomb pulse dating. This method has other forensic applications, including investigation of frauds related to food and wine counterfeiting, dating of opium crops and dating of substances used in biological warfare. AMS extends the applicability of the radiocarbon method, allowing the analysis of 14 C in submilligram organic samples. Specific molecular compounds extracted from bones, hair, skin and other carbon bearing substances of forensic significance can now be dated, enhancing the sensitivity and reliability of chronological determinations. AMS can also be used to analyse rare actinide isotopes released into the environment during the clandestine production of nuclear weapons or associated with the smuggling of nuclear materials. In

  3. Updating dating down under

    International Nuclear Information System (INIS)

    Bristow, J.W.

    1986-01-01

    The article deals with the Sensitive High Resolution Ion Microprobe (SHRIMP), Australia's only microprobe and its applications for geochronology. SHRIMP has the ability to analyse tiny areas (less than 30μm across) within crystals directly, the only sample preparation required being polishing of the crystal surface. Most analyses so far have been done on separated crystals prepared as grain mounts, although an increasing number of analyses are now being made of crystals in rock thin sections where their textural associations can be established. Important features of SHRIMP are its double-focusing mass spectrometer and great physical size, more than 8 meters long, employing a magnet weighing six tons. This enables the machine to distinguish ions with atomic masses differing by less than one part in ten thousand while at the same time having a very great sensitivity. SHRIMP was used for dating crustal zircons from southern African Kimberlites. Although low U and Pb abundances presents problems in peak selection and focusing on SHRIMP its was found that kimberlitic zircons could be dated successfully

  4. Radiocarbon dates XXI

    International Nuclear Information System (INIS)

    Lowdon, J.A.; Blake, W. Jr.

    1981-01-01

    This list includes 105 radiocarbon age determinations on 104 geological samples made by the Radiocarbon Dating Laboratory. They are on samples from various areas as follows: Labrador Shelf (2); Newfoundland (12); Nova Scotia (2); New Brunswick (1); Quebec (3); Ontario (1); Manitoba (1); Alberta (2); British Columbia (15); Yukon Territory (35); Northwest Territories, Mainland (10); Northwest Territories, Arctic Archipelago (21). Details of background and standard for the 2 L and 5 L counters during the period from November 4, 1980 to October 31, 1981 are summarized in Tables 1 and 2; Table 3 gives the number of counts used to determine the average background and standard counting rates; and Table 4 lists the number of different background and standard gas preparations used for counting

  5. Experimental investigation of radiative thermal rectifier using vanadium dioxide

    Energy Technology Data Exchange (ETDEWEB)

    Ito, Kota, E-mail: kotaito@mosk.tytlabs.co.jp [Toyota Central Research and Development Labs, Nagakute, Aichi 480-1192 (Japan); Research Center for Advanced Science and Technology (RCAST), The University of Tokyo, Komaba, Meguro-ku, Tokyo 153-8904 (Japan); Nishikawa, Kazutaka; Iizuka, Hideo [Toyota Central Research and Development Labs, Nagakute, Aichi 480-1192 (Japan); Toshiyoshi, Hiroshi [Research Center for Advanced Science and Technology (RCAST), The University of Tokyo, Komaba, Meguro-ku, Tokyo 153-8904 (Japan)

    2014-12-22

    Vanadium dioxide (VO{sub 2}) exhibits a phase-change behavior from the insulating state to the metallic state around 340 K. By using this effect, we experimentally demonstrate a radiative thermal rectifier in the far-field regime with a thin film VO{sub 2} deposited on the silicon wafer. A rectification contrast ratio as large as two is accurately obtained by utilizing a one-dimensional steady-state heat flux measurement system. We develop a theoretical model of the thermal rectifier with optical responses of the materials retrieved from the measured mid-infrared reflection spectra, which is cross-checked with experimentally measured heat flux. Furthermore, we tune the operating temperatures by doping the VO{sub 2} film with tungsten (W). These results open up prospects in the fields of thermal management and thermal information processing.

  6. Dates fruits classification using SVM

    Science.gov (United States)

    Alzu'bi, Reem; Anushya, A.; Hamed, Ebtisam; Al Sha'ar, Eng. Abdelnour; Vincy, B. S. Angela

    2018-04-01

    In this paper, we used SVM in classifying various types of dates using their images. Dates have interesting different characteristics that can be valuable to distinguish and determine a particular date type. These characteristics include shape, texture, and color. A system that achieves 100% accuracy was built to classify the dates which can be eatable and cannot be eatable. The built system helps the food industry and customer in classifying dates depending on specific quality measures giving best performance with specific type of dates.

  7. Influence of the Kinetics of Heat and Mass Transfer in a Binary-Rectification Column on the Realizability Range of its Regimes

    Science.gov (United States)

    Zaeva, M. A.; Tsirlin, A. M.; Sukin, I. A.

    2018-05-01

    The range of realizable rates of flows in a binary-rectification column in which heat is supplied into the boiler and is removed from the dephlegmator was investigated. It is shown that this range is determined by two characteristic parameters related to the kinetics of heat and mass transfer in the column and the composition of the mixture subjected to separation. The limiting capabilities of a cascade of two binary-rectification columns for the separation of a ternary mixture in it were considered. The conditions for an optimum sequence of separation of a mixture in this cascade and for a consistent arrangement of its heat and mass exchange surfaces and the relation between the ultimate production rate of the cascade and the total heat losses in it were determined.

  8. Current limiting experiment with 600 V/100A rectification type superconducting fault current limiter; 600 V-100A kyu seiryugata chodendo genryuki no genryu shiken

    Energy Technology Data Exchange (ETDEWEB)

    Matsuzaki, J.; Tsurunaga, K.; Urata, M. [Toshiba Corp., Tokyo (Japan); Okuma, T.; Sato, Y.; Iwata, Y. [Tokyo Electric Power Co., Inc., Tokyo (Japan)

    1999-06-07

    The rectification type current limiter with the current-limiting system of the new type which combined rectifier circuits with the direct current reactor has been proposed until now, and it has succeeded in the current-limiting test by the normal conduction reactor by the 6.6kV class model vessel. Since the loss of the conductor becomes fundamentally the zero, in the same current limiter, by using superconducting wire rod, because direct current always flows in the reactor, making into low-loss becomes possible. In this report, this paper describes cut-off characteristic of 600V/100A rectification type superconductive current limiter using the metal type superconductive conductor. (NEDO)

  9. Band Alignment for Rectification and Tunneling Effects in Al2O3 Atomic-Layer-Deposited on Back Contact for CdTe Solar Cell.

    Science.gov (United States)

    Su, Yantao; Xin, Chao; Feng, Yancong; Lin, Qinxian; Wang, Xinwei; Liang, Jun; Zheng, Jiaxin; Lin, Yuan; Pan, Feng

    2016-10-11

    The present work intends to explain why ultrathin Al 2 O 3 atomic-layer-deposited (ALD) on the back contact with rectification and tunneling effects can significantly improve the performance of CdTe solar cells in our previous work [ Liang , J. ; et al. Appl. Phys. Lett. 2015 , 107 , 013907 ]. Herein, we further study the mechanism through establishing the interfacial energy band diagram configuration of the ALD Al 2 O 3 /Cu x Te by experiment of X-ray photoelectron spectroscopy and first-principles calculations and conclude to find the band alignment with optimized layer thickness (about 1 nm ALD Al 2 O 3 ) as the key factor for rectification and tunneling effects.

  10. Dating technique tested

    International Nuclear Information System (INIS)

    Anon.

    1985-01-01

    An analytical technique for dating ground water and polar ice up to a million years old has been successfully tested by scientists at Oak Ridge National Laboratory (ORNL). The system, known as a rare gas atom counter, extends the capabilities of resonance ionization mass spectrometry to include counting single atoms of krypton-81. The counter is composed of a pulsed dye laser operated in tandem with a mass spectrometer to separate the various isotopes of krypton. In a collaborative study, ORNL scientists recently used the method for the first time to count krypton-81 in a liter of ground water removed from a sandstone aquifer near Zurich. Fewer than 1000 krypton-81 atoms were isolated from the ground water samples. According to Bernard Lehman, a collaborating geochemist at the University of Bern, this first test proved that counting the small numbers of krypton-81 atoms necessary to make an estimate of the age of water could actually be done. Among the applications of this method, Lehman says, could be improved siting of locations for the disposal of radioactive wastes

  11. Modulating optical rectification, second and third harmonic generation of doped quantum dots: Interplay between hydrostatic pressure, temperature and noise

    Science.gov (United States)

    Ganguly, Jayanta; Saha, Surajit; Bera, Aindrila; Ghosh, Manas

    2016-10-01

    We examine the profiles of optical rectification (OR), second harmonic generation (SHG) and third harmonic generation (THG) of impurity doped QDs under the combined influence of hydrostatic pressure (HP) and temperature (T) in presence and absence of Gaussian white noise. Noise has been incorporated to the system additively and multiplicatively. In order to study the above nonlinear optical (NLO) properties the doped dot has been subjected to a polarized monochromatic electromagnetic field. Effect of application of noise is nicely reflected through alteration of peak shift (blue/red) and variation of peak height (increase/decrease) of above NLO properties as temperature and pressure are varied. All such changes again sensitively depends on mode of application (additive/multiplicative) of noise. The remarkable influence of interplay between noise strength and its mode of application on the said profiles has also been addressed. The findings illuminate fascinating role played by noise in tuning above NLO properties of doped QD system under the active presence of both hydrostatic pressure and temperature.

  12. Photon-phonon-enhanced infrared rectification in a two-dimensional nanoantenna-coupled tunnel diode

    International Nuclear Information System (INIS)

    Kadlec, Emil A.; Jarecki, Robert L.; Starbuck, Andrew; Peters, David W.; Davids, Paul S.

    2016-01-01

    The interplay of strong infrared photon-phonon coupling with electromagnetic confinement in nanoscale devices is demonstrated to have a large impact on ultrafast photon-assisted tunneling in metal-oxide-semiconductor (MOS) structures. Infrared active optical phonon modes in polar oxides lead to strong dispersion and enhanced electric fields at material interfaces. We find that the infrared dispersion of SiO_2 near a longitudinal optical phonon mode can effectively impedance match a photonic surface mode into a nanoscale tunnel gap that results in large transverse-field confinement. An integrated 2D nanoantenna structure on a distributed large-area MOS tunnel-diode rectifier is designed and built to resonantly excite infrared surface modes and is shown to efficiently channel infrared radiation into nanometer-scale gaps in these MOS devices. This enhanced-gap transverse-electric field is converted to a rectified tunneling displacement current resulting in a dc photocurrent. We examine the angular and polarization-dependent spectral photocurrent response of these 2D nanoantenna-coupled tunnel diodes in the photon-enhanced tunneling spectral region. Lastly, our 2D nanoantenna-coupled infrared tunnel-diode rectifier promises to impact large-area thermal energy harvesting and infrared direct detectors.

  13. [Project Shared Medical Record in Catalonia, Spain: legal framework and enforcement of rights of access, rectification, cancellation and opposition (ARCO)].

    Science.gov (United States)

    Borrás-Pascual, Maria Josep; Busquets-Font, Josep Maria; García-Martínez, Anna; Manent-González, Martí

    2010-02-01

    The Constitution and especially the Constitutional Court's jurisprudence have recognized the so-called right of habeas data, providing legal protection at the highest level of personal data. Health information, falls within the scope of protection, but we see that there are peculiarities in the health and development legislation that compels us to treat such information with special characteristics. This article will review the citizen's rights to access to health information, taking into account both the protection of personal data such as regulating access to specific health information and tools that have been developed for the exercise of these rights under the "Shared Medical Record" project developed by the Department of Health of the Generalitat of Catalonia. In particular the rights that are discussed are: the right of access to information, the right of correction, the right of cancellation. The right of access to information enables anyone to know if their personal data are processed, the purpose of treatment and the available information on the origin of personal data. In addition the law also allows to know whether the data have been disclosed to a third party. The right of rectification gives -concerned in this case the patient- the right to correct any data that contain errors. The cancellation right is restricted to situations where it really is exercising a right of correction against information. Finally, the right to object is for patients to be able to oppose their health data is consulted by various health care facilities to generate them. 2010 Elsevier España S.L. All rights reserved.

  14. Mechanics and complications of reverse shoulder arthroplasty: morse taper failure analysis and prospective rectification

    International Nuclear Information System (INIS)

    Hoskin, HLD; Furie, E; Ganey, TM; Schlatterer, DR; Collins, W

    2017-01-01

    Since Sir John Charnley began his monumental hip arthroplasty work in 1958, clinical researchers have been incrementally improving longevity and functionality of total joint systems, although implant failure occurs on occasion. The purpose of this study is to report the fracture of the humeral tray Morse taper of a reverse total shoulder system (RTSS), which to date has not been reported with metallurgic analysis for any RTSS. There was no reported antecedent fall, motor vehicle collision, or other traumatic event prior to implant fracture in this case. Analysis was performed on the retrieved failed implant by Scanning Electron Microscopy (SEM) and Electron Dispersion Spectroscopy (EDS) in an attempt to determine the failure method, as well as to offer improvements for future implants. At the time of revision surgery all explants were retained from the left shoulder of a 61-year old male who underwent a non-complicated RTSS 4 years prior. The explants, particularly the cracked humeral tray, were processed as required for SEM and EDS. Analysis was performed on the failure sites in order to determine the chemical composition of the different parts of the implant, discover the chemical composition of the filler metal used during the electron beam welding process, and to detect any foreign elements that could suggest corrosion or other evidence of failure etiology. Gross visual inspection of all explants revealed that implant failure was a result of dissociation of the taper from the humeral tray at the weld, leaving the Morse taper embedded in the humeral stem while the tray floated freely in the patient’s shoulder. SEM further confirmed the jagged edges noted grossly at the weld fracture site, both suggesting failure due to torsional forces. EDS detected elevated levels of carbon and oxygen at the fracture site on the taper only and not on the humeral tray. In order to determine the origin of the high levels of C and O, it was considered that in titanium alloys, C

  15. Luminescence dating of Netherland's sediments

    NARCIS (Netherlands)

    Wallinga, J.; Davids, F.; Dijkmans, J.W.A.

    2007-01-01

    Over the last decades luminescence dating techniques have been developed that allow earth scientists to determine the time of deposition of sediments. In this contribution we revity: 1) the development of the methodology, 2) tests of the reliability of luminescence dating on Netherlands' sediments;

  16. The isotopic dating of crystals

    International Nuclear Information System (INIS)

    Giuliani, G.; Cheilletz, A.

    1995-01-01

    The first part of this work deals with the answer to the question : why are the crystals dated ? Then, some isotopic dating methods are described : U-Th-Pb, K-Ar, 40 Ar/ 39 Ar, Rb-Sr, Sm-Nd, fission traces, carbon 14 methods. Examples concerning emeralds and diamonds are given. (O.L.). 12 refs., 2 figs

  17. The comparison of absolute dating (Radiocarbon dating) and relative dating of Pringapus and Gondosuli temples

    International Nuclear Information System (INIS)

    Faisal, W; Arumbinang, H; Taftazani, A; Widayati, S; Sumiyatno; Suhardi

    1996-01-01

    The absolute dating (radiocarbon, 14 C dating) and relative dating of Pringapus and Gondosuli temples in Temanggung regency (district) of Central Java Province have been carried out. The field sampling was done especially with the purpose to obtain vertical data, so that excavation method was adopted in the case. The main data were the ecofacts of organic habitation such as bones, woods, charcoals, shells, and paper artefacts. The artefacts data were used as a comparison. The comparative data analysis were conducted at Yogyakarta archaeological Department Laboratory, thus included dating of artefacts which were performed according to archaeological analysis procedures, generally based on the attributes attached to the artefacts, whereas the absolute dating of charcoal samples were performed in the Radiocarbon Dating Laboratory at Yogyakarta Nuclear Research Centre. Based on the relative dating of epigraphy content on the andesit rock from Gondosuli Temple which showed the year of 754 Saka or 832 AD, the Pringapus Temple was estimated to be built in the 850 AD. According to the absolute dating (Radiocarbon Dating with delta 13 C and tree ring corrections) the age for Gondosuli temple based on GDS/LU-2/Spit-7 samples is (384 -602) AD and from GDS/LU-2/Spit-8 = (452 - 652) AD. With these significant differences in the results obtained, it can be concluded that culture environment where the sample were collected already existed before the temple was built. Further investigation is still required

  18. Conduction and rectification in NbO x - and NiO-based metal-insulator-metal diodes

    Energy Technology Data Exchange (ETDEWEB)

    Osgood, Richard M.; Giardini, Stephen; Carlson, Joel; Periasamy, Prakash; Guthrey, Harvey; O' Hayre, Ryan; Chin, Matthew; Nichols, Barbara; Dubey, Madan; Fernandes, Gustavo; Kim, Jin Ho; Xu, Jimmy; Parilla, Philip; Berry, Joseph; Ginley, David

    2016-09-01

    Conduction and rectification in nanoantenna-coupled NbOx- and NiO-based metal-insulator-metal (MIM) diodes ('nanorectennas') are studied by comparing new theoretical predictions with the measured response of nanorectenna arrays. A new quantum mechanical model is reported and agrees with measurements of current-voltage (I-V) curves, over 10 orders of magnitude in current density, from [NbOx(native)-Nb2O5]- and NiO-based samples with oxide thicknesses in the range of 5-36 nm. The model, which introduces new physics and features, including temperature, electron effective mass, and image potential effects using the pseudobarrier technique, improves upon widely used earlier models, calculates the MIM diode's I-V curve, and predicts quantitatively the rectification responsivity of high frequency voltages generated in a coupled nanoantenna array by visible/near-infrared light. The model applies both at the higher frequencies, when high-energy photons are incident, and at lower frequencies, when the formula for classical rectification, involving derivatives of the I-V curve, may be used. The rectified low-frequency direct current is well-predicted in this work's model, but not by fitting the experimentally measured I-V curve with a polynomial or by using the older Simmons model (as shown herein). By fitting the measured I-V curves with our model, the barrier heights in Nb-(NbOx(native)-Nb2O5)-Pt and Ni-NiO-Ti/Ag diodes are found to be 0.41/0.77 and 0.38/0.39 eV, respectively, similar to literature reports, but with effective mass much lower than the free space value. The NbOx (native)-Nb2O5 dielectric properties improve, and the effective Pt-Nb2O5 barrier height increases as the oxide thickness increases. An observation of direct current of ~4 nA for normally incident, focused 514 nm continuous wave laser beams are reported, similar in magnitude to recent reports. This measured direct current is compared to the prediction for rectified direct current

  19. Interfacial Thermal Transport via One-Dimensional Atomic Junction Model

    Directory of Open Access Journals (Sweden)

    Guohuan Xiong

    2018-03-01

    Full Text Available In modern information technology, as integration density increases rapidly and the dimension of materials reduces to nanoscale, interfacial thermal transport (ITT has attracted widespread attention of scientists. This review introduces the latest theoretical development in ITT through one-dimensional (1D atomic junction model to address the thermal transport across an interface. With full consideration of the atomic structures in interfaces, people can apply the 1D atomic junction model to investigate many properties of ITT, such as interfacial (Kapitza resistance, nonlinear interface, interfacial rectification, and phonon interference, and so on. For the ballistic ITT, both the scattering boundary method (SBM and the non-equilibrium Green’s function (NEGF method can be applied, which are exact since atomic details of actual interfaces are considered. For interfacial coupling case, explicit analytical expression of transmission coefficient can be obtained and it is found that the thermal conductance maximizes at certain interfacial coupling (harmonic mean of the spring constants of the two leads and the transmission coefficient is not a monotonic decreasing function of phonon frequency. With nonlinear interaction—phonon–phonon interaction or electron–phonon interaction at interface, the NEGF method provides an efficient way to study the ITT. It is found that at weak linear interfacial coupling, the nonlinearity can improve the ITT, but it depresses the ITT in the case of strong-linear coupling. In addition, the nonlinear interfacial coupling can induce thermal rectification effect. For interfacial materials case which can be simulated by a two-junction atomic chain, phonons show interference effect, and an optimized thermal coupler can be obtained by tuning its spring constant and atomic mass.

  20. AHP 47: A NIGHT DATE

    Directory of Open Access Journals (Sweden)

    Phun tshogs dbang rgyal ཕུན་ཚོགས་དབང་རྒྱལ།

    2017-04-01

    Full Text Available The author was born in 1993 in Ska chung (Gaqun Village, Nyin mtha' (Ningmute Township, Rma lho (Henan Mongolian Autonomous County, Rma lho (Huangnan Tibetan Autonomous Prefecture, Mtsho sngon (Qinghai Province, PR China. Night dating was popular for teenage boys some years ago. They rode horses and yaks when they went night dating. They generally rode yaks, because horses were important for their families and used for such important tasks as pursuing bandits and going to the county town for grain and supplies. An early experience with night dating is described.

  1. Thermal transport across graphene and single layer hexagonal boron nitride

    International Nuclear Information System (INIS)

    Zhang, Jingchao; Hong, Yang; Yue, Yanan

    2015-01-01

    As the dimensions of nanocircuits and nanoelectronics shrink, thermal energies are being generated in more confined spaces, making it extremely important and urgent to explore for efficient heat dissipation pathways. In this work, the phonon energy transport across graphene and hexagonal boron-nitride (h-BN) interface is studied using classic molecular dynamics simulations. Effects of temperature, interatomic bond strength, heat flux direction, and functionalization on interfacial thermal transport are investigated. It is found out that by hydrogenating graphene in the hybrid structure, the interfacial thermal resistance (R) between graphene and h-BN can be reduced by 76.3%, indicating an effective approach to manipulate the interfacial thermal transport. Improved in-plane/out-of-plane phonon couplings and broadened phonon channels are observed in the hydrogenated graphene system by analyzing its phonon power spectra. The reported R results monotonically decrease with temperature and interatomic bond strengths. No thermal rectification phenomenon is observed in this interfacial thermal transport. Results reported in this work give the fundamental knowledge on graphene and h-BN thermal transport and provide rational guidelines for next generation thermal interface material designs

  2. Dating the humans by radiocarbon

    International Nuclear Information System (INIS)

    Fedi, M.E.

    2011-01-01

    Radiocarbon has become a very powerful tool used for dating. This paper deals with a specific application of 1 4C i.e. dating of humans. Attention is focused on those aspects that, if neglected, might lead to a misinterpretation of the results or to an unsatisfying accuracy of the measurement. After a brief description of the main principles on which the radiocarbon method is based and of Accelerator Mass Spectrometry, examples taken from the research activity of INFN-LABEC (Laboratorio di Tecniche Nucleari per I Beni Culturali) in Florence are presented. The case of the relic of St. Francis represents an example of dating not directly human remains but other objects that can be associated to them. The case of two burials from the archaeological area of Baratti-Populonia, in Tuscany, gives the possibility to show the importance of estimating the human palaeodiet when dating bone samples.

  3. Dating by electron paramagnetic resonance

    International Nuclear Information System (INIS)

    Poupeau, G.; Rossi, A.M.

    1984-01-01

    Some natural materials behave like dosimeters in front of the ionizing particle flux coming from environmental radioactivity and the cosmic radiation. This property is used for the dating by Electron Paramagnetic Resonance (EPR). Before presenting the basic principles of the EPR analysis and the dating method which uses such a phenomenous, it is reviewed several types of application currently in course of development. (L.C.) [pt

  4. Radiocarbon dating of lake sediments

    OpenAIRE

    Pocevičius, Matas

    2016-01-01

    Matas Pocevičius, Radiocarbon dating of lake sediments, bachelor thesis, Vilnius University, Faculty of Physics, Department of General Physics and Spectroscopy, physics, Vilnius, 45 p., 2016. The aim of this study is to evaluate the possibility of radiocarbon dating application for Tapeliai lake bottom sediments. The literature review discusses topics related to accelerator mass spectrometry, principles of radiocarbon formation, importance of nuclear fallout for 14C, possible applications of ...

  5. Precision 3d Surface Reconstruction from Lro Nac Images Using Semi-Global Matching with Coupled Epipolar Rectification

    Science.gov (United States)

    Hu, H.; Wu, B.

    2017-07-01

    The Narrow-Angle Camera (NAC) on board the Lunar Reconnaissance Orbiter (LRO) comprises of a pair of closely attached high-resolution push-broom sensors, in order to improve the swath coverage. However, the two image sensors do not share the same lenses and cannot be modelled geometrically using a single physical model. Thus, previous works on dense matching of stereo pairs of NAC images would generally create two to four stereo models, each with an irregular and overlapping region of varying size. Semi-Global Matching (SGM) is a well-known dense matching method and has been widely used for image-based 3D surface reconstruction. SGM is a global matching algorithm relying on global inference in a larger context rather than individual pixels to establish stable correspondences. The stereo configuration of LRO NAC images causes severe problem for image matching methods such as SGM, which emphasizes global matching strategy. Aiming at using SGM for image matching of LRO NAC stereo pairs for precision 3D surface reconstruction, this paper presents a coupled epipolar rectification methods for LRO NAC stereo images, which merges the image pair in the disparity space and in this way, only one stereo model will be estimated. For a stereo pair (four) of NAC images, the method starts with the boresight calibration by finding correspondence in the small overlapping stripe between each pair of NAC images and bundle adjustment of the stereo pair, in order to clean the vertical disparities. Then, the dominate direction of the images are estimated by project the center of the coverage area to the reference image and back-projected to the bounding box plane determined by the image orientation parameters iteratively. The dominate direction will determine an affine model, by which the pair of NAC images are warped onto the object space with a given ground resolution and in the meantime, a mask is produced indicating the owner of each pixel. SGM is then used to generate a disparity

  6. PRECISION 3D SURFACE RECONSTRUCTION FROM LRO NAC IMAGES USING SEMI-GLOBAL MATCHING WITH COUPLED EPIPOLAR RECTIFICATION

    Directory of Open Access Journals (Sweden)

    H. Hu

    2017-07-01

    Full Text Available The Narrow-Angle Camera (NAC on board the Lunar Reconnaissance Orbiter (LRO comprises of a pair of closely attached high-resolution push-broom sensors, in order to improve the swath coverage. However, the two image sensors do not share the same lenses and cannot be modelled geometrically using a single physical model. Thus, previous works on dense matching of stereo pairs of NAC images would generally create two to four stereo models, each with an irregular and overlapping region of varying size. Semi-Global Matching (SGM is a well-known dense matching method and has been widely used for image-based 3D surface reconstruction. SGM is a global matching algorithm relying on global inference in a larger context rather than individual pixels to establish stable correspondences. The stereo configuration of LRO NAC images causes severe problem for image matching methods such as SGM, which emphasizes global matching strategy. Aiming at using SGM for image matching of LRO NAC stereo pairs for precision 3D surface reconstruction, this paper presents a coupled epipolar rectification methods for LRO NAC stereo images, which merges the image pair in the disparity space and in this way, only one stereo model will be estimated. For a stereo pair (four of NAC images, the method starts with the boresight calibration by finding correspondence in the small overlapping stripe between each pair of NAC images and bundle adjustment of the stereo pair, in order to clean the vertical disparities. Then, the dominate direction of the images are estimated by project the center of the coverage area to the reference image and back-projected to the bounding box plane determined by the image orientation parameters iteratively. The dominate direction will determine an affine model, by which the pair of NAC images are warped onto the object space with a given ground resolution and in the meantime, a mask is produced indicating the owner of each pixel. SGM is then used to

  7. Radiocarbon dating of iron artefacts

    Energy Technology Data Exchange (ETDEWEB)

    Cresswell, R. [Australian National Univ., Canberra, ACT (Australia). Dept. of Nuclear Physics

    1997-12-31

    Iron artefacts are generally dated by association or on stylistic grounds. This may not give a true indication of the date of manufacture, or may not be possible if the piece is out of context, ambiguous in style, or a copy. Obtaining a direct date on the artefact would be preferable. During the processes of manufacture, carbon is incorporated into the iron from the fuel source. If the fuel is of a material containing contemporaneous carbon, i.e. has an ambient radiocarbon signature, e.g. charcoal, then we may reliably radiocarbon date the artefact by extracting this carbon. Care must be taken, however, to ensure that re-working has not introduced multiple sources of carbon that would give an erroneous date. Detailed chemical analysis must precede radiocarbon analysis. Sample size is determined by carbon content, and before the advent of accelerator mass spectrometry, several tens of grams of carbon were required for radiocarbon dating (van der Merwe, 1969), prohibiting this method except for high-carbon cast-irons and bulk samples, e.g. caches of nails. AMS permits the analysis of sub-gram pieces of iron (Cresswell, 1991), thereby permitting the analysis of museum pieces with only minimal loss of material, and small fragments of iron recovered from archaeological sites. A few examples are given to illustrate these points. Paper no. 41; Extended abstract. 6 refs.

  8. Radiocarbon dating of iron artefacts

    International Nuclear Information System (INIS)

    Cresswell, R.

    1997-01-01

    Iron artefacts are generally dated by association or on stylistic grounds. This may not give a true indication of the date of manufacture, or may not be possible if the piece is out of context, ambiguous in style, or a copy. Obtaining a direct date on the artefact would be preferable. During the processes of manufacture, carbon is incorporated into the iron from the fuel source. If the fuel is of a material containing contemporaneous carbon, i.e. has an ambient radiocarbon signature, e.g. charcoal, then we may reliably radiocarbon date the artefact by extracting this carbon. Care must be taken, however, to ensure that re-working has not introduced multiple sources of carbon that would give an erroneous date. Detailed chemical analysis must precede radiocarbon analysis. Sample size is determined by carbon content, and before the advent of accelerator mass spectrometry, several tens of grams of carbon were required for radiocarbon dating (van der Merwe, 1969), prohibiting this method except for high-carbon cast-irons and bulk samples, e.g. caches of nails. AMS permits the analysis of sub-gram pieces of iron (Cresswell, 1991), thereby permitting the analysis of museum pieces with only minimal loss of material, and small fragments of iron recovered from archaeological sites. A few examples are given to illustrate these points

  9. Microscale radiocarbon dating of paintings

    International Nuclear Information System (INIS)

    Hendriks, Laura; Hajdas, Irka; McIntyre, Cameron; Kueffner, Markus; Ferreira, Ester S.B.; Scherrer, Nadim C.

    2016-01-01

    In this paper, radiocarbon dating of paintings using minimal sample sizes has been investigated, in an effort to address the problem of limited access to sample material in paintings. 14 C analyses were conducted on signed and dated paintings from two Swiss artists of the twentieth century. The selected paintings dated from the 1930s and 1960s, provided the opportunity to evaluate the dating accuracy on paintings realized before and after 1950 AD when the 14 C bomb peak was created, as a result of the nuclear tests conducted in the 1950/1960s. The work focused on the one hand on minimizing the size of the canvas sample required for accelerator mass spectrometer radiocarbon measurement on the gas ion source of the MICADAS and, on the other hand, on testing the possibility of dating the organic binder of the paint. Following careful characterization of the paint composition by X-ray fluorescence spectroscopy, Fourier transformed infrared spectroscopy, and Raman spectroscopy, paints containing no other carbon source than the natural organic binder were identified and dated. (orig.)

  10. Direct dating of human fossils.

    Science.gov (United States)

    Grün, Rainer

    2006-01-01

    The methods that can be used for the direct dating of human remains comprise of radiocarbon, U-series, electron spin resonance (ESR), and amino acid racemization (AAR). This review gives an introduction to these methods in the context of dating human bones and teeth. Recent advances in ultrafiltration techniques have expanded the dating range of radiocarbon. It now seems feasible to reliably date bones up to 55,000 years. New developments in laser ablation mass spectrometry permit the in situ analysis of U-series isotopes, thus providing a rapid and virtually non-destructive dating method back to about 300,000 years. This is of particular importance when used in conjunction with non-destructive ESR analysis. New approaches in AAR analysis may lead to a renaissance of this method. The potential and present limitations of these direct dating techniques are discussed for sites relevant to the reconstruction of modern human evolution, including Florisbad, Border Cave, Tabun, Skhul, Qafzeh, Vindija, Banyoles, and Lake Mungo. (c) 2006 Wiley-Liss, Inc.

  11. Microscale radiocarbon dating of paintings

    Energy Technology Data Exchange (ETDEWEB)

    Hendriks, Laura; Hajdas, Irka; McIntyre, Cameron [ETH Zurich, Ion Beam Physics, Zurich (Switzerland); Kueffner, Markus; Ferreira, Ester S.B. [SIK-ISEA, Zurich, Zurich (Switzerland); Scherrer, Nadim C. [Bern University of Applied Sciences, HKB, Bern (Switzerland)

    2016-03-15

    In this paper, radiocarbon dating of paintings using minimal sample sizes has been investigated, in an effort to address the problem of limited access to sample material in paintings. {sup 14}C analyses were conducted on signed and dated paintings from two Swiss artists of the twentieth century. The selected paintings dated from the 1930s and 1960s, provided the opportunity to evaluate the dating accuracy on paintings realized before and after 1950 AD when the {sup 14}C bomb peak was created, as a result of the nuclear tests conducted in the 1950/1960s. The work focused on the one hand on minimizing the size of the canvas sample required for accelerator mass spectrometer radiocarbon measurement on the gas ion source of the MICADAS and, on the other hand, on testing the possibility of dating the organic binder of the paint. Following careful characterization of the paint composition by X-ray fluorescence spectroscopy, Fourier transformed infrared spectroscopy, and Raman spectroscopy, paints containing no other carbon source than the natural organic binder were identified and dated. (orig.)

  12. Influence of static and dynamic dipolar fields in bulk YIG/thin film NiFe systems probed via spin rectification effect

    Energy Technology Data Exchange (ETDEWEB)

    Soh, Wee Tee, E-mail: a0046479@u.nus.edu [Center for Superconducting and Magnetic Materials, Department of Physics, National University of Singapore, 2 Science Drive 3, Singapore 117551 (Singapore); Tay, Z.J. [Center for Superconducting and Magnetic Materials, Department of Physics, National University of Singapore, 2 Science Drive 3, Singapore 117551 (Singapore); Yakovlev, N.L. [Institute of Materials Research and Engineering, A*STAR (Agency for Science, Technology and Research), 3 Research Link, Singapore 117602 (Singapore); Peng, Bin [State Key Laboratory of Electronic Thin Films and Integrated Devices, University of Electronic Science and Technology of China, Chengdu 610054 (China); Ong, C.K. [Center for Superconducting and Magnetic Materials, Department of Physics, National University of Singapore, 2 Science Drive 3, Singapore 117551 (Singapore); Temasek Laboratories, National University of Singapore, 5A Engineering Drive 2, Singapore 117411 (Singapore)

    2017-03-15

    The characteristics of the static and dynamic components of the dipolar fields originating from a bulk polycrystalline yttrium iron garnet (YIG) substrate are probed by depositing a NiFe (Permalloy) layer on it, which acts as a detector. By measuring dc voltages generated via spin rectification effect (SRE) within the NiFe layer under microwave excitation, we characterize the influence of dipolar fields from bulk YIG on the NiFe layer. It is found that the dynamic YIG dipolar fields modify the self-SRE of NiFe, driving its own rectification voltages within the NiFe layer, an effect we term as non-local SRE. This non-local SRE only occurs near the simultaneous resonance of both YIG and NiFe. On the other hand, the static dipolar field from YIG manifests itself as a negative anisotropy in the NiFe layer which shifts the latter’s ferromagnetic resonance frequency. - Highlights: • We demonstrate the quantification of both the static and dynamic components of the dipolar fields due to a YIG slab. • The detection and characterisation of such dipolar fields are important in many magnetic applications such as magnonics. • The dipolar fields can pose potential pitfalls if not properly considered in certain spin-electronics systems.

  13. Linguistic Dating of Biblical Texts

    DEFF Research Database (Denmark)

    Ehrensvärd, Martin Gustaf

    2003-01-01

    For two centuries, scholars have pointed to consistent differences in the Hebrew of certain biblical texts and interpreted these differences as reflecting the date of composition of the texts. Until the 1980s, this was quite uncontroversial as the linguistic findings largely confirmed the chronol......For two centuries, scholars have pointed to consistent differences in the Hebrew of certain biblical texts and interpreted these differences as reflecting the date of composition of the texts. Until the 1980s, this was quite uncontroversial as the linguistic findings largely confirmed...... the chronology of the texts established by other means: the Hebrew of Genesis-2 Kings was judged to be early and that of Esther, Daniel, Ezra, Nehemiah, and Chronicles to be late. In the current debate where revisionists have questioned the traditional dating, linguistic arguments in the dating of texts have...... come more into focus. The study critically examines some linguistic arguments adduced to support the traditional position, and reviewing the arguments it points to weaknesses in the linguistic dating of EBH texts to pre-exilic times. When viewing the linguistic evidence in isolation it will be clear...

  14. Kimberley rock art dating project

    International Nuclear Information System (INIS)

    Walsh, G.L.; Morwood, M.

    1997-01-01

    The art's additional value, unequalled by traditionally recognised artefacts, is its permanent pictorial documentation presenting a 'window' into the otherwise intangible elements of perceptions, vision and mind of pre-historic cultures. Unfortunately it's potential in establishing Kimberley archaeological 'big picture' still remains largely unrecognised. Some of findings of the Kimberley Rock Art Dating Project, using AMS and optical stimulated luminescence (OSL) dating techniques, are outlined. It is estimated that these findings will encourage involvement by a greater diversity of specialist disciplines to tie findings into levels of this art sequence as a primary reference point. The sequence represents a sound basis for selecting specific defined images for targeting detailed studies by a range of dating technique. This effectively removes the undesirable ad hoc sampling of 'apparently old paintings'; a process which must unavoidably remain the case with researchers working on most global bodies of rock art

  15. ESR dating of fault rocks

    International Nuclear Information System (INIS)

    Lee, Hee Kwon

    2002-03-01

    Past movement on faults can be dated by measurement of the intensity of ESR signals in quartz. These signals are reset by local lattice deformation and local frictional heating on grain contacts at the time of fault movement. The ESR signals then trow back as a result of bombardment by ionizing radiation from surrounding rocks. The age is obtained from the ratio of the equivalent dose, needed to produce the observed signal, to the dose rate. Fine grains are more completely reset during faulting, and a plot of age vs grain size shows a plateau for grains below critical size : these grains are presumed to have been completely zeroed by the last fault activity. We carried out ESR dating of fault rocks collected from the Yangsan fault system. ESR dates from the this fault system range from 870 to 240 ka. Results of this research suggest that long-term cyclic fault activity continued into the pleistocene

  16. ESR dating of fault rocks

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Hee Kwon [Kangwon National Univ., Chuncheon (Korea, Republic of)

    2002-03-15

    Past movement on faults can be dated by measurement of the intensity of ESR signals in quartz. These signals are reset by local lattice deformation and local frictional heating on grain contacts at the time of fault movement. The ESR signals then trow back as a result of bombardment by ionizing radiation from surrounding rocks. The age is obtained from the ratio of the equivalent dose, needed to produce the observed signal, to the dose rate. Fine grains are more completely reset during faulting, and a plot of age vs grain size shows a plateau for grains below critical size : these grains are presumed to have been completely zeroed by the last fault activity. We carried out ESR dating of fault rocks collected from the Yangsan fault system. ESR dates from the this fault system range from 870 to 240 ka. Results of this research suggest that long-term cyclic fault activity continued into the pleistocene.

  17. Fission track dating of kimberlitic zircons

    International Nuclear Information System (INIS)

    Haggerty, S.E.

    1983-01-01

    The only reliable method for dating kimberlites at present is the lengthy and specialized hydrothermal procedure that extracts 206 Pb and 238 U from low-uranium zircons. This paper describes a second successful method by fission track dating of large single-crystal zircons, 1.0-1.5 cm in dimension. The use of large crystals overcomes the limitations imposed in conventional fission track analysis which utilizes crushed fragments. Low track densities, optical track dispersion, and the random orientation of polished surfaces in the etch and irradiation cycle are effectively overcome. Fission track ages of zircons from five African kimberlites are reported, from the Kimberley Pool (90.0 +- 6.5 m.y.), Orapa (87.4 +- 5.7 and 92.4 +- 6.1 m.y.), Nzega (51.1 +- 3.8 m.y.), Koffiefontein (90.9 +- 8.2 m.y.), and Val do Queve (133.4 +- 11.5 m.y.). In addition we report the first radiometric ages (707.9 +- 59.6 and 705.5 +- 61.0 m.y.) of crustal zircons from kimberlites in northwest Liberia. The fission track ages agree well with earlier age estimates. Most of the zircons examined in this study are zoned with respect to uranium but linear correlations are established (by regression analysis) between zones of variable uranium content, and within zones of constant uranium content (by analysis of variance). Concordance between the fission track method and the U/Pb technique is established and we concluded that track fading from thermal annealing has not taken place. Kimberlitic zircons dated in this study, therefore, record the time of eruption. (orig.)

  18. 32Si dating of sediments

    International Nuclear Information System (INIS)

    Morgenstern, U.

    2004-01-01

    Brief explanation of the use of 32 Si in the dating of sediments. 32 Si , with a half-life of c.140 years, can be applied in the age range 30-1000 years. An appropriate dating tool for that time range is essential because it includes three very important epochs: the impact of human colonisation and industrialisation during the last 150 years, the Little Ice Age between about 1650 AD and 1850 AD, and the last part of the Medieval Climatic Optimum. 23 refs

  19. The complexity behind the date

    CERN Multimedia

    2009-01-01

    For the waiting world, and indeed for most of us here at CERN, ‘the LHC schedule’ simply means the date that the LHC will restart - and we only take notice when that end-date changes. But in fact the schedule is a constantly evolving intricate document coordinating all the repairs, consolidation and commissioning in every part of the machine. So, what actually goes on behind the scenes in timing and planning all the work on one of the most complex scientific instruments ever built?

  20. Sexual Intimacy in Dating Relationships

    Science.gov (United States)

    Peplau, Letitia Anne; And Others

    1977-01-01

    The patterning of sexual interaction in male-female dyads and the links between sexual behavior and emotional intimacy were investigated as part of a two-year study of college dating couples. Traditional sexual role playing was found to be common. (Author/AM)

  1. Online Dating and Conjugal Bereavement

    Science.gov (United States)

    Young, Dannagal Goldthwaite; Caplan, Scott E.

    2010-01-01

    This study examined self-presentation in the online dating profiles of 241 widowed and 280 divorced individuals between 18 and 40 years old. A content analysis of open-ended user-generated profiles assessed the presence or absence of various themes, including the user's marital status, the backstory of their lost relationship, and whether they…

  2. (including travel dates) Proposed itinerary

    Indian Academy of Sciences (India)

    Ashok

    31 July to 22 August 2012 (including travel dates). Proposed itinerary: Arrival in Bangalore on 1 August. 1-5 August: Bangalore, Karnataka. Suggested institutions: Indian Institute of Science, Bangalore. St Johns Medical College & Hospital, Bangalore. Jawaharlal Nehru Centre, Bangalore. 6-8 August: Chennai, TN.

  3. Comparative study of radioimmunoassay dates

    International Nuclear Information System (INIS)

    Venegas Sanchez, Ruth.

    1986-01-01

    The radioimmunoassay is frequently used in clinical chemistry for the concentration determination of several substances like hormones as thyrotropine and thyroxine. In this experiment the dates of tyroxine radioimmunoassay are processed by three methods: a) like the recommendation of the IAEA, b) Dr. G. Chase method, c) according to the provider. The best method was Dr. Chase's. (author)

  4. Peer Group Influences on Adolescent Dating Aggression

    Science.gov (United States)

    Connolly, Jennifer; Friedlander, Laura

    2009-01-01

    The peer group is a critical social context for dating and romantic relationships. Peer groups provide opportunities to meet potential dating partners and set norms for acceptable dating behaviors. This article explores how peer groups influence dating and dating aggression, as well as how they can be used in prevention efforts. It also reviews…

  5. 31 CFR 596.302 - Effective date.

    Science.gov (United States)

    2010-07-01

    ... FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY TERRORISM LIST GOVERNMENTS SANCTIONS REGULATIONS General Definitions § 596.302 Effective date. The term effective date refers to the effective date of the...

  6. The TAC of porcelain samples and its influence on TL dating

    International Nuclear Information System (INIS)

    Leung, P.L.; Stokes, M.J.; Xia Junding; Wang Weida

    1997-01-01

    The thermal activation characteristics of porcelain slice samples for pre-dose dating were obtained by using the multiple activation method. The influence of activation temperature on TL dating was also studied. The results show that choosing a temperature corresponding to the maximum sensitivity on the TAC curve as the activation temperature is very important in the multiple activation method

  7. Linguistic dating of biblical texts

    DEFF Research Database (Denmark)

    Young, Ian; Rezetko, Robert; Ehrensvärd, Martin Gustaf

    Since the beginning of critical scholarship biblical texts have been dated using linguistic evidence. In recent years this has become a controversial topic, especially with the publication of Ian Young (ed.), Biblical Hebrew: Studies in Chronology and Typology (2003). However, until now there has...... been no introduction and comprehensive study of the field. Volume 1 introduces the field of linguistic dating of biblical texts, particularly to intermediate and advanced students of biblical Hebrew who have a reasonable background in the language, having completed at least an introductory course...... in this volume are: What is it that makes Archaic Biblical Hebrew archaic , Early Biblical Hebrew early , and Late Biblical Hebrew late ? Does linguistic typology, i.e. different linguistic characteristics, convert easily and neatly into linguistic chronology, i.e. different historical origins? A large amount...

  8. Scaling submillimeter single-cycle transients toward megavolts per centimeter field strength via optical rectification in the organic crystal OH1.

    Science.gov (United States)

    Ruchert, Clemens; Vicario, Carlo; Hauri, Christoph P

    2012-03-01

    We present the generation of high-power single-cycle terahertz (THz) pulses in the organic salt crystal 2-[3-(4-hydroxystyryl)-5.5-dimethylcyclohex-2-enylidene]malononitrile or OH1. Broadband THz radiation with a central frequency of 1.5 THz (λ(c)=200 μm) and high electric field strength of 440 kV/cm is produced by optical rectification driven by the signal of a powerful femtosecond optical parametric amplifier. A 1.5% pump to THz energy conversion efficiency is reported, and pulse energy stability better than 1% RMS is achieved. An approach toward the realization of higher field strength is discussed. © 2012 Optical Society of America

  9. Fission tracks dating for obsidian

    International Nuclear Information System (INIS)

    Picon, C.

    1991-01-01

    Obsidian from South America are dated by fission tracks methods. Samples are irradiated in a nuclear reactor with a flux of 10 15 n/cm 2 . Results, corrected by 'Plateau' methods, are the following: obsidian from Bolivia: 4.14 x 10 6 yr., Ecuador: 8.79 x 10 5 yr., Colombia: 3.52 x 10 6 yr., Peru: 6.55 x 10 6 yr., Chile: 1.13 x 10 6 yr. (MMZ). 5 refs., 3 tabs

  10. Radiokrypton dating coming of age

    Institute of Scientific and Technical Information of China (English)

    Zheng-Tian Lu

    2016-01-01

    The dream of radiokrypton dating began in 1969 when Heinz Hugo Loosli and Hans Oeschger of the University of Bern first detected the decay of81Rr(half-life=230 000 yr)in krypton gas extracted from air[1].This isotope is produced in the upper atmosphere by cosmic-ray-induced spallation and neutron-activation of stable krypton.Due to its long residence time(105 yr)in the atmosphere,81Rr is uniformly

  11. Current topics in ESR dating

    International Nuclear Information System (INIS)

    Skinner, Anne R.

    2011-01-01

    After over 25 years, the use of electron spin resonance (ESR) is well-established in dating sites of geological, paleontological and archaeological interest. Like any scientific technique, there have been changes in understanding and in methodology. Improvements have not, however, changed the observation that external dose calculations are still a significant source of uncertainty in ages. Examples from Europe, Africa and the Americans illustrate this point. For Pradayrol Cave (France), the occupation age, 330 ka, is unchallenged, making this the oldest known Neanderthal site in France. For Roc de Marsal, also in France, on the other hand, discrepancies between TL and sedimentary dose rates imply substantial differences in interpretation. In the Western Egyptian Desert, where artifacts and datable material are not well-correlated, the dating results show consistency with expectations based on global climate change, even in deflated sites. Climate change is also the question in geological studies in the Bahamas where, despite concerns about cosmic dose history, ESR dates confirm other evidence for sea level changes. We show that an uncertain age is not the same as an impossible one.

  12. ESR dating of fault rocks

    International Nuclear Information System (INIS)

    Lee, Hee Kwon

    2003-02-01

    Past movement on faults can be dated by measurement of the intensity of ESR signals in quartz. These signals are reset by local lattice deformation and local frictional heating on grain contacts at the time of fault movement. The ESR signals then grow back as a result of bombardment by ionizing radiation from surrounding rocks. The age is obtained from the ratio of the equivalent dose, needed to produce the observed signal, to the dose rate. Fine grains are more completely reset during faulting, and a plot of age vs. grain size shows a plateau for grains below critical size; these grains are presumed to have been completely zeroed by the last fault activity. We carried out ESR dating of fault rocks collected near the Gori nuclear reactor. Most of the ESR signals of fault rocks collected from the basement are saturated. This indicates that the last movement of the faults had occurred before the Quaternary period. However, ESR dates from the Oyong fault zone range from 370 to 310 ka. Results of this research suggest that long-term cyclic fault activity of the Oyong fault zone continued into the Pleistocene

  13. ESR dating of fault rocks

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Hee Kwon [Kangwon National Univ., Chuncheon (Korea, Republic of)

    2003-02-15

    Past movement on faults can be dated by measurement of the intensity of ESR signals in quartz. These signals are reset by local lattice deformation and local frictional heating on grain contacts at the time of fault movement. The ESR signals then grow back as a result of bombardment by ionizing radiation from surrounding rocks. The age is obtained from the ratio of the equivalent dose, needed to produce the observed signal, to the dose rate. Fine grains are more completely reset during faulting, and a plot of age vs. grain size shows a plateau for grains below critical size; these grains are presumed to have been completely zeroed by the last fault activity. We carried out ESR dating of fault rocks collected near the Gori nuclear reactor. Most of the ESR signals of fault rocks collected from the basement are saturated. This indicates that the last movement of the faults had occurred before the Quaternary period. However, ESR dates from the Oyong fault zone range from 370 to 310 ka. Results of this research suggest that long-term cyclic fault activity of the Oyong fault zone continued into the Pleistocene.

  14. Design of the low-temperature rectification plant KRETA including the pre-purification units ADAMO and REDUKTION and first operating experience

    International Nuclear Information System (INIS)

    Ammon, R. v.; Hutter, E.; Leichsenring, C.H.; Weinlaender, W.

    1977-01-01

    In the off-gas treatment system developed by the GfK Karlsruhe the noble gases Kr and Xe are removed by means of a low-temperature rectification process, in which the Kr-85 is largely separated from the inactive Xe. The Xe can then be released to the environment, while the radioactive Kr must be stored in steel cylinders. Prior to the above treatment the oxygen is removed to minimize ozone formation. This is effected, together with the removal of residual oxides of nitrogen, by catalytic reduction with hydrogen. At a subsequent stage of the pre-purification process all the gaseous components which could freeze out in the cryogenic section, i.e. H 2 O, CO 2 and NH 3 , and are removed by adsorption. These stages of the process are being investigated in the reduced-scale KRETA, REDUKTION and ADAMO pilot plants, which have a gas through-put of 50 m 3 /h (at N.T.P.), using simulated inactive gas mixtures. The design of the three plants is described. The initial tests on the KRETA plant showed that an experimental decontamination factor of >= 10 3 could be achieved for the first column for rectification of the N 2 -Kr-Xe system. Instances of xenon freezing out were also observed, these being accompanied by a drop in the decontamination factor. Separation of Kr from Xe in the second column proceeded smoothly with high enrichment of both components. Both the capacity and the efficiency of the ADAMO plant are very high for the separat ion of H 2 O and CO 2 . Coadsorbed Kr can be fully desorbed under normal conditions by flushing with N 2 . Following preliminary laboratory tests for the REDUKTION plant a ruthenium catalyst has been selected, which is particularly insensitive to poisoning, e.g. by iodine. (orig./ORU) [de

  15. First 226Ra- 210Pb dating of a young speleothem

    Science.gov (United States)

    Condomines, M.; Rihs, S.

    2006-10-01

    Whereas the method based on the decrease of excess 210Pb has already been used to date young (Age determination of recent cave deposits using excess 210Pb — A new technique, Geophys. Res. Lett. 20 (1993) 603-606.]), this paper presents the first dating of a speleothem through the 226Ra- 210Pb method. Dating of a young hydrothermal stalagmite from the Mt Cornadore cave (St Nectaire, French Massif Central) was made possible by the high 226Ra and negligible 210Pb contents of such carbonates, formed by precipitation from CO 2-rich thermal waters. ( 210Pb/ 226Ra) ratios regularly increase with depth along the axis of the 33 cm long stalagmite. The age-depth relationship can be interpreted by two main phases of growth, with high but variable axial growth rates of 5.3 mm/yr from 1909 to 1967, and 2.6 mm/yr from 1967 to 1989 (alternatively, the oldest phase can be subdivided in three episodes with growth rates varying from 2 to 7 mm/yr). Thin-section examination reveals the presence of numerous laminae, indicating infra-annual variations. We suggest that this fine layered structure might reflect short-term fluctuations in drip waters, possibly induced by near-surface mixing between thermal and ground waters, and ultimately linked to the pluviometry. A detailed examination of this laminated structure combined with 226Ra- 210Pb dating could thus provide a high-resolution record of local paleohydrological fluctuations.

  16. Role of radiation dating technique - one example

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, Shigueo [Universidade de Sao Paulo (IF/USP), SP (Brazil). Inst. de Fisica; Etchevarne, Carlos A. [Universidade Federal da Bahia (UFBA), Salvador, BA (Brazil). Fac. de Filosofia e Ciencias Humanas. Dept. Antropologia e Etnologia; Cano, Nilo F.; Munita, C.S. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2012-07-01

    Full text: The great majority of archaeological or geological dating technique is based on radiation effect. The so called radioactivity method uses radioactive decays of elements. This is the case of the well known radiocarbon or carbon-14 method. Also the method of relating daughter nucleus to decaying nucleus, as in K-40/Ar-40, Th- 230/U-234, etc. Here we will concentrate in the method based on energy deposition in a solid by radiation from the disintegration of U-series and Th-series. {beta}-rays emitted by the decay of K-40 into Ca-40 (80%) and Ar-40 (11%) also contributes. The role of {alpha}, {beta} and {gamma} radiation emitted by radionuclides in the U-238 and Th-232 series and of {beta} rays from the decay of K-40, all of them in the soil irradiate anything in their course. For dating, we can have sediments as well as potteries produced by ancient people and became buried. The important process consists in transferring a fraction of the energy of radiation to the solid, mainly liberating electrons from valence band to conduction band and from there to traps. In many case the energy of the radiation is used to create defects which in turn create energy levels (traps) in the forbidden gap (or energy gap). There are three ways to recover the energy stored in the solid: (1) by emission of light optically stimulated (OSL), (2) by emission of light thermally stimulated (TL), (3) by microwave absorption (EPR or ESR). Using these techniques among several applications, we will present one to find the first settlers in the northeaster region of Brazil. (author)

  17. Role of radiation dating technique - one example

    International Nuclear Information System (INIS)

    Watanabe, Shigueo

    2012-01-01

    Full text: The great majority of archaeological or geological dating technique is based on radiation effect. The so called radioactivity method uses radioactive decays of elements. This is the case of the well known radiocarbon or carbon-14 method. Also the method of relating daughter nucleus to decaying nucleus, as in K-40/Ar-40, Th- 230/U-234, etc. Here we will concentrate in the method based on energy deposition in a solid by radiation from the disintegration of U-series and Th-series. β-rays emitted by the decay of K-40 into Ca-40 (80%) and Ar-40 (11%) also contributes. The role of α, β and γ radiation emitted by radionuclides in the U-238 and Th-232 series and of β rays from the decay of K-40, all of them in the soil irradiate anything in their course. For dating, we can have sediments as well as potteries produced by ancient people and became buried. The important process consists in transferring a fraction of the energy of radiation to the solid, mainly liberating electrons from valence band to conduction band and from there to traps. In many case the energy of the radiation is used to create defects which in turn create energy levels (traps) in the forbidden gap (or energy gap). There are three ways to recover the energy stored in the solid: (1) by emission of light optically stimulated (OSL), (2) by emission of light thermally stimulated (TL), (3) by microwave absorption (EPR or ESR). Using these techniques among several applications, we will present one to find the first settlers in the northeaster region of Brazil. (author)

  18. Thermal transport through a spin-phonon interacting junction: A nonequilibrium Green's function method study

    Science.gov (United States)

    Zhang, Zu-Quan; Lü, Jing-Tao

    2017-09-01

    Using the nonequilibrium Green's function method, we consider heat transport in an insulating ferromagnetic spin chain model with spin-phonon interaction under an external magnetic field. Employing the Holstein-Primakoff transformation to the spin system, we treat the resulted magnon-phonon interaction within the self-consistent Born approximation. We find the magnon-phonon coupling can change qualitatively the magnon thermal conductance in the high-temperature regime. At a spectral mismatched ferromagnetic-normal insulator interface, we also find thermal rectification and negative differential thermal conductance due to the magnon-phonon interaction. We show that these effects can be effectively tuned by the external applied magnetic field, a convenient advantage absent in anharmonic phonon and electron-phonon systems studied before.

  19. School Counselors' Role in Dating Violence Intervention

    Science.gov (United States)

    Craigen, Laurie M.; Sikes, April; Healey, Amanda; Hays, Danica

    2009-01-01

    Dating violence among adolescents is a major public health concern. The purpose of this paper is to examine five factors of which school counselors must be aware in order to recognize, intervene, and report incidence of dating violence. These factors are (a) understanding the diverse definitions of dating violence, (b) recognizing dating violence…

  20. Transient thermal camouflage and heat signature control

    Science.gov (United States)

    Yang, Tian-Zhi; Su, Yishu; Xu, Weikai; Yang, Xiao-Dong

    2016-09-01

    Thermal metamaterials have been proposed to manipulate heat flux as a new way to cloak or camouflage objects in the infrared world. To date, however, thermal metamaterials only operate in the steady-state and exhibit detectable, transient heat signatures. In this letter, the theoretical basis for a thermal camouflaging technique with controlled transient diffusion is presented. This technique renders an object invisible in real time. More importantly, the thermal camouflaging device instantaneously generates a pre-designed heat signature and behaves as a perfect thermal illusion device. A metamaterial coating with homogeneous and isotropic thermal conductivity, density, and volumetric heat capacity was fabricated and very good camouflaging performance was achieved.

  1. Thermoluminescence dating of pleistocene sediments

    International Nuclear Information System (INIS)

    Poupeau, G.; Souza, J.H.; Rivera, A.

    1984-01-01

    After a short introduction on recent trends in quaternary geochronology, this article focuses on the thermoluminescence dating of sediments, whose principles and present limits and prospects are discussed. Results are presented for the TL behaviour of sands from various geological contexts in Brazil. They show that the coarse (approx. 100-200μm) quartz fraction of coastal and intra continental, eolian and fluvial-type deposits, might be datable by TL from the upper Holocene to at least the basis of the upper Pleistocene, with a precision of + - 10-15%. (Author) [pt

  2. Thermoluminescence dating of pleistocene sediments

    International Nuclear Information System (INIS)

    Poupeau, G.; Souza, J.H.

    1984-01-01

    After a short introduction on recent trends in quaternary geochronology, this article focuses on the thermoluminescence (TL) dating of sediments, whose principles, present limits and prospects are discussed. Results are presented for TL behavior of sands from various geological contexts in Brazil. They show that the coarse (approx. 100-200 μm) quartz fraction of coastal and intracontinental, eolian and fluvial - type deposits, might be datable by TL from the upper Holocene to at least the base of the upper Pleistocene, with a precision of +- 10-15%. (Author) [pt

  3. Paleomagnetic dating: Methods, MATLAB software, example

    Science.gov (United States)

    Hnatyshin, Danny; Kravchinsky, Vadim A.

    2014-09-01

    A MATLAB software tool has been developed to provide an easy to use graphical interface for the plotting and interpretation of paleomagnetic data. The tool takes either paleomagnetic directions or paleopoles and compares them to a user defined apparent polar wander path or secular variation curve to determine the age of a paleomagnetic sample. Ages can be determined in two ways, either by translating the data onto the reference curve, or by rotating it about a set location (e.g. sampling location). The results are then compiled in data tables which can be exported as an excel file. This data can also be plotted using variety of built-in stereographic projections, which can then be exported as an image file. This software was used to date the giant Sukhoi Log gold deposit in Russia. Sukhoi Log has undergone a complicated history of faulting, folding, metamorphism, and is the vicinity of many granitic bodies. Paleomagnetic analysis of Sukhoi Log allowed for the timing of large scale thermal or chemical events to be determined. Paleomagnetic analysis from gold mineralized black shales was used to define the natural remanent magnetization recorded at Sukhoi Log. The obtained paleomagnetic direction from thermal demagnetization produced a paleopole at 61.3°N, 155.9°E, with the semi-major axis and semi-minor axis of the 95% confidence ellipse being 16.6° and 15.9° respectively. This paleopole is compared to the Siberian apparent polar wander path (APWP) by translating the paleopole to the nearest location on the APWP. This produced an age of 255.2- 31.0+ 32.0Ma and is the youngest well defined age known for Sukhoi Log. We propose that this is the last major stage of activity at Sukhoi Log, and likely had a role in determining the present day state of mineralization seen at the deposit.

  4. Substitution of Sugar with Dates Powder and Dates Syrup in Cookies Making

    OpenAIRE

    W.A. Alsenaien; R.A. Alamer; Zhen-Xing Tang; S.A. Albahrani; M.A. Al-Ghannam; S.M. Aleid

    2015-01-01

    In this study, the effects of dates powder and dates syrup as a sugar substitution, on the physical properties and sensory attributes of cookies were studied. An increase in firmness and moisture content of cookies supplemented with dates was obtained. The diameter and spread ratio of cookies showed a decrease with increasing levels of date powder or date syrup. Partial replacement of sugar with date powder or date syrup produced cookies with more dark and red color. Sensory evaluation result...

  5. Thermal comfort

    CSIR Research Space (South Africa)

    Osburn, L

    2010-01-01

    Full Text Available Thermal comfort is influenced by environmental parameters as well as other influences including asymmetric heating and cooling conditions. Additionally, some aspects of thermal comfort may be exploited so as to enable a building to operate within a...

  6. 85Kr dating of groundwater

    International Nuclear Information System (INIS)

    Rozanski, K.; Florkowski, T.

    1978-01-01

    The possibility of 85 Kr dating of groundwater is being investigated. The method of gas extraction from 200 to 300 litres of water sample has been developed. The Argon and Krypton mixture, separated from the gas extracted from water, was counted in a 1.5 ml volume proportional counter. The amount of krypton gas in the counter was determined by mass spectrometry. A number of surface and groundwater samples were analyzed indicating an 85 Kr concentration ranging from present atmospheric content (river water) to zero values. 85 Kr 'blank value' was determined to be about 5 per cent of present 85 Kr atmospheric content. For groundwater samples, the mean residence time in the system was calculated assuming the exponential model and known 85 Kr input function. Further improvement of the method should bring higher yield of krypton separation and lower volume of water necessary for analysis. (orig.) [de

  7. Blind-date Conversation Joining

    Directory of Open Access Journals (Sweden)

    Luca Cesari

    2013-07-01

    Full Text Available We focus on a form of joining conversations among multiple parties in service-oriented applications where a client may asynchronously join an existing conversation without need to know in advance any information about it. More specifically, we show how the correlation mechanism provided by orchestration languages enables a form of conversation joining that is completely transparent to clients and that we call 'blind-date joining'. We provide an implementation of this strategy by using the standard orchestration language WS-BPEL. We then present its formal semantics by resorting to COWS, a process calculus specifically designed for modelling service-oriented applications. We illustrate our approach by means of a simple, but realistic, case study from the online games domain.

  8. Making a date with radiocarbon

    International Nuclear Information System (INIS)

    Gribbin, J.

    1979-01-01

    The use of 14 C dating techniques for samples of organic materials up to 50,000 years old is discussed with especial reference to adjustment necessary to take account of both the most recent figure for the 14 C half-life and also the natural fluctuations in the production of 14 C over 50,000 years. Methods of detection and the accuracy of the measurements are considered. It is hoped that future developments including both the possibility of counting 14 C ions directly using an accelerator as a mass spectrometer, and also the use of laser enrichment techniques will not only push back the radiocarbon calendar to 100,000 years but will also allow the use of much smaller samples than before. (U.K.)

  9. Make a date with a tree

    International Nuclear Information System (INIS)

    Baillie, M.; Pilcher, J.

    1988-01-01

    The paper concerns the use of dendrochronology to check the accuracy of radiocarbon dating. The Belfast chronology is described - this involves wood samples precisely dated by tree ring analysis and analysed by high-precision radiocarbon analysis. The analysis resulted in the first continuous high-precision calibration of the radiocarbon time-scale, and confirmed the relationship between radiocarbon dates and tree-ring dates. The use of radiocarbon dating to reveal the age of wood samples that have too few rings to produce an accurate date, is also outlined. (U.K.)

  10. The scientific dating of standing buildings.

    Science.gov (United States)

    Alcock, Nathaniel W

    2017-11-17

    The techniques of dendrochronology (tree-ring dating) and radiocarbon (14C) dating are described, as they are applied to historic buildings. Both rely on determining the felling dates of the trees used in their construction. For dendrochronology, the construction of master chronologies and the matching of individual ring-width sequences to them is described and, for radiocarbon dating, the use of tree-ring results in calibration. Results of dating are discussed, ranging from the cathedrals of Peterborough and Beauvais and the development of crown-post roof structures, to the dating and identification of standing medieval peasant houses, particularly those built using cruck construction.

  11. 17 CFR 248.128 - Effective date, compliance date, and prospective application.

    Science.gov (United States)

    2010-04-01

    ... Affiliate Marketing § 248.128 Effective date, compliance date, and prospective application. (a) Effective date. This subpart is effective September 10, 2009. (b) Mandatory compliance date. Compliance with this... 17 Commodity and Securities Exchanges 3 2010-04-01 2010-04-01 false Effective date, compliance...

  12. Radiocarbon dates for Rangitoto and Motutapu, a consideration of dating accuracy

    International Nuclear Information System (INIS)

    Law, R.G.

    1975-01-01

    The carbon dates for the eruptions of Rangitoto and the occupation of Maori sites on Motutapu contain inconsistencies which are explicable only after the dates have been corrected to allow for the nature of the dating method. The only date which is reasonably established is a 14th or 15th century dating for the ash shower covering Motutapu. (auth.)

  13. Geophysical Insights from Archaeomagnetic Dating

    Science.gov (United States)

    Holme, R.; Lodge, A.; Suttie, N.; Shaw, J.; Hill, M. J.; Linford, P.

    2009-12-01

    We report on work which has been undertaken towards developing an improved methodology for archaeomagnetic dating of archaeological samples through the use of a dedicated field model. In this talk, we focus on the more general (non-archaeological) implications of our results. Our work has focused on Europe, taking advantage of the better spatial and temporal coverage of available samples. Nevertheless, we model the field globally, using an a priori model (such as, for example, CALS7K) to constrain the field away from the regions of available data. This is advantageous over the use of a local field modelling methodology, as it allows us to examine the physical consequences of structure in our model (for example, in terms of the spectra of the field and secular variation at the core-mantle boundary), and to control possible edge effects in the model, which in a local model might produce an unphysical solution. By focusing on one particular region, we produce models that may not be optimal in terms of global structure, but allow us to investigate the data content in the region where it may provide the most information on core-field evolution. In parallel, we have been expanding the archaeointensity record for Great Britain, towards producing an archaeointensity curve for the UK which could ultimately be used for dating of unoriented samples (such as pot sherds). This new record, combined with other recently acquired high-quality intensity data, allows us to consider the evolution of global geomagnetic field strength in parallel with a good model of directional measurements; from 1590, the GUFM model is appropriate. Recent attempts to determine global intensity variation have used all available data (some of uncertain quality) to quantify variations in field strength. By instead focusing on a more limited dataset of known quality, we are able to examine intensity trends in greater detail. We present evidence that the intensity of the field was higher prior to 1840 than

  14. Dates and Times Made Easy with lubridate

    Directory of Open Access Journals (Sweden)

    Garrett Grolemund

    2011-04-01

    Full Text Available This paper presents the lubridate package for R, which facilitates working with dates and times. Date-times create various technical problems for the data analyst. The paper highlights these problems and oers practical advice on how to solve them using lubridate. The paper also introduces a conceptual framework for arithmetic with date-times in R.

  15. Designing thermal diode and heat pump based on DNA nanowire: Multifractal approach

    Energy Technology Data Exchange (ETDEWEB)

    Behnia, S., E-mail: s.behnia@iaurmia.ac.ir; Panahinia, R.

    2017-07-12

    The management of heat flow in DNA nano wire was considered. Thermal diode effect in DNA and the domain of its appearance dependent to system parameters have been detected. The appearance of directed thermal flow in thermodynamic sizes proposes the possibility of designing the macroscopic thermal rectifier. By applying driven force, pumping effect has been also observed. The resonance frequency of DNA and threshold amplitudes of driving force for attaining permanent pumping effect have been detected. Forasmuch as detecting negative differential thermal resistance (NDTR) phenomenon, DNA can act as a thermal transistor. By using an analytical parallel investigation based on Rényi spectrum analysis, threshold values to transition to NDTR and pumping regimes have been detected. - Highlights: • The control and management of heat current in DNA have been investigated. • Directed thermal flow and NDTR in DNA have been identified. • By increasing the system size, the reversed thermal rectification appeared. So, it is proposed the possibility of designing the macroscopic thermal rectifier. • Pumping effect accompanied with detection of resonance frequency of DNA has been observed. • To verify the results, we did a parallel analysis based on multifractal concept to detect threshold values for transition to pumping state and NDTR regime.

  16. Gate-tunable diode-like current rectification and ambipolar transport in multilayer van der Waals ReSe2/WS2 p-n heterojunctions.

    Science.gov (United States)

    Wang, Cong; Yang, Shengxue; Xiong, Wenqi; Xia, Congxin; Cai, Hui; Chen, Bin; Wang, Xiaoting; Zhang, Xinzheng; Wei, Zhongming; Tongay, Sefaattin; Li, Jingbo; Liu, Qian

    2016-10-12

    Vertically stacked van der Waals (vdW) heterojunctions of two-dimensional (2D) transition metal dichalcogenides (TMDs) have attracted a great deal of attention due to their fascinating properties. In this work, we report two important gate-tunable phenomena in new artificial vdW p-n heterojunctions created by vertically stacking p-type multilayer ReSe 2 and n-type multilayer WS 2 : (1) well-defined strong gate-tunable diode-like current rectification across the p-n interface is observed, and the tunability of the electronic processes is attributed to the tunneling-assisted interlayer recombination induced by majority carriers across the vdW interface; (2) the distinct ambipolar behavior under gate voltage modulation both at forward and reverse bias voltages is found in the vdW ReSe 2 /WS 2 heterojunction transistors and a corresponding transport model is proposed for the tunable polarity behaviors. The findings may provide some new opportunities for building nanoscale electronic and optoelectronic devices.

  17. Effect of the magnetic field on the nonlinear optical rectification and second and third harmonic generation in double δ-doped GaAs quantum wells

    Science.gov (United States)

    Martínez-Orozco, J. C.; Rojas-Briseño, J. G.; Rodríguez-Magdaleno, K. A.; Rodríguez-Vargas, I.; Mora-Ramos, M. E.; Restrepo, R. L.; Ungan, F.; Kasapoglu, E.; Duque, C. A.

    2017-11-01

    In this paper we are reporting the computation for the Nonlinear Optical Rectification (NOR) and the Second and Third Harmonic Generation (SHG and THG) related with electronic states of asymmetric double Si-δ-doped quantum well in a GaAs matrix when this is subjected to an in-plane (x-oriented) constant magnetic field effect. The work is performed in the effective mass and parabolic band approximations in order to compute the electronic structure for the system by a diagonalization procedure. The expressions for the nonlinear optical susceptibilities, χ0(2), χ2ω(2), and χ3ω(3), are those arising from the compact matrix density formulation and stand for the NOR, SHG, and THG, respectively. This asymmetric double δ-doped quantum well potential profile actually exhibits nonzero NOR, SHG, and THG responses which can be easily controlled by the in-plane (x-direction) externally applied magnetic field. In particular we find that for the chosen configuration the harmonic generation is in the far-infrared/THz region, thus and becoming suitable building blocks for photodetectors in this range of the electromagnetic spectra.

  18. Studies on a Hybrid Full-Bridge/Half-Bridge Bidirectional CLTC Multi-Resonant DC-DC Converter with a Digital Synchronous Rectification Strategy

    Directory of Open Access Journals (Sweden)

    Shu-huai Zhang

    2018-01-01

    Full Text Available This study presents a new bidirectional multi-resonant DC-DC converter, which is named CLTC. The converter adds an auxiliary transformer and an extra resonant capacitor based on a LLC resonant DC-DC converter, achieving zero-voltage switching (ZVS for the input inverting switches and zero-current switching (ZCS for the output rectifiers in all load range. The converter also has a wide gain range in two directions. When the load is light, a half-bridge configuration is adopted instead of a full-bridge configuration to solve the problem of voltage regulation. By this method, the voltage gain becomes monotonous and controllable. Besides, the digital synchronous rectification strategy is proposed in forward mode without adding any auxiliary circuit. The conduction time of synchronous rectifiers equals the estimation value of body diodes’ conduction time with the lightest load. Power loss analysis is also conducted in different situations. Finally, the theoretical analysis is validated by a 5 kW prototype.

  19. Reservoir effects in radiocarbon dating

    International Nuclear Information System (INIS)

    Head, M.J.

    1997-01-01

    Full text: The radiocarbon dating technique depends essentially on the assumption that atmospheric carbon dioxide containing the cosmogenic radioisotope 14 C enters into a state of equilibrium with all living material (plants and animals) as part of the terrestrial carbon cycle. Terrestrial reservoir effects occur when the atmospheric 14 C signal is diluted by local effects where systems depleted in 14 C mix with systems that are in equilibrium with the atmosphere. Naturally, this can occur with plant material growing close to an active volcano adding very old CO 2 to the atmosphere (the original 14 C has completely decayed). It can also occur in highly industrialised areas where fossil fuel derived CO 2 dilutes the atmospheric signal. A terrestrial reservoir effect can occur in the case of fresh water shells living in rivers or lakes where there is an input of ground water from springs or a raising of the water table. Soluble bicarbonate derived from the dissolution of very old limestone produces a 14 C dilution effect. Land snail shells and stream carbonate depositions (tufas and travertines) can be affected by a similar mechanism. Alternatively, in specific cases, these reservoir effects may not occur. This means that general interpretations assuming quantitative values for these terrestrial effects are not possible. Each microenvironment associated with samples being analysed needs to be evaluated independently. Similarly, the marine environment produces reservoir effects. With respect to marine shells and corals, the water depth at which carbonate growth occurs can significantly affect quantitative 14 C dilution, especially in areas where very old water is uplifted, mixing with top layers of water that undergo significant exchange with atmospheric CO 2 . Hence, generalisations with respect to the marine reservoir effect also pose problems. These can be exacerbated by the mixing of sea water with either terrestrial water in estuaries, or ground water where

  20. Thermal insulation

    International Nuclear Information System (INIS)

    Aspden, G.J.; Howard, R.S.

    1988-01-01

    The patent concerns high temperature thermal insulation of large vessels, such as the primary vessel of a liquid metal cooled nuclear reactor. The thermal insulation consists of multilayered thermal insulation modules, and each module comprises a number of metal sheet layers sandwiched between a back and front plate. The layers are linked together by straps and clips to control the thickness of the module. (U.K.)

  1. Uranium-series dating of gypsum speleothems: methodology and examples.

    Directory of Open Access Journals (Sweden)

    Sanna Laura

    2010-01-01

    Full Text Available The analytical problems of dating gypsum speleothems with the U-series technique are reviewed. Gypsum speleothems are, in general, very low in U content, challenging the limits of detection methods. Various approaches to dissolving gypsum and isolation of actinides from the matrix include ion-pairing dissolution with magnesium salts and using nitric acid. The most precise dating technique is Thermal Ionization Mass Spectrometry (TIMS, combined with Fe(OH3 scavenging and anionic exchange chromatography. Less satisfactory, but much quicker, is direct retention of actinides from HNO3 by means of TRU resin and MC-ICP-MS detection. We have tested these methods on gypsum speleothems from the Sorbas karst in Spain and from the Naica caves in Mexico.

  2. Selective Epitaxy of InP on Si and Rectification in Graphene/InP/Si Hybrid Structure.

    Science.gov (United States)

    Niu, Gang; Capellini, Giovanni; Hatami, Fariba; Di Bartolomeo, Antonio; Niermann, Tore; Hussein, Emad Hameed; Schubert, Markus Andreas; Krause, Hans-Michael; Zaumseil, Peter; Skibitzki, Oliver; Lupina, Grzegorz; Masselink, William Ted; Lehmann, Michael; Xie, Ya-Hong; Schroeder, Thomas

    2016-10-12

    The epitaxial integration of highly heterogeneous material systems with silicon (Si) is a central topic in (opto-)electronics owing to device applications. InP could open new avenues for the realization of novel devices such as high-mobility transistors in next-generation CMOS or efficient lasers in Si photonics circuitry. However, the InP/Si heteroepitaxy is highly challenging due to the lattice (∼8%), thermal expansion mismatch (∼84%), and the different lattice symmetries. Here, we demonstrate the growth of InP nanocrystals showing high structural quality and excellent optoelectronic properties on Si. Our CMOS-compatible innovative approach exploits the selective epitaxy of InP nanocrystals on Si nanometric seeds obtained by the opening of lattice-arranged Si nanotips embedded in a SiO 2 matrix. A graphene/InP/Si-tip heterostructure was realized on obtained materials, revealing rectifying behavior and promising photodetection. This work presents a significant advance toward the monolithic integration of graphene/III-V based hybrid devices onto the mainstream Si technology platform.

  3. Thermal insulation

    International Nuclear Information System (INIS)

    Pinsky, G.P.

    1977-01-01

    Thermal insulation for vessels and piping within the reactor containment area of nuclear power plants is disclosed. The thermal insulation of this invention can be readily removed and replaced from the vessels and piping for inservice inspection, can withstand repeated wettings and dryings, and can resist high temperatures for long periods of time. 4 claims, 3 figures

  4. Radiocarbon dating of soils, a review

    International Nuclear Information System (INIS)

    Scharpenseel, H.W.; Schiffmann, H.

    1977-01-01

    The application of radiocarbon dating techniques for pedological purposes is reviewed in chronological sequence of its phases of introduction. Initially dating of charcoal and buried paleosols was dominating and accompanied by few soil dating attempts of recent soil formations on the basis of extracted humic acid-C. The following controversy regarding the potentialities and limitations of recent soil dating, still being involved in the intact turnover processes of modern biodynamics, led to intensive search for the relatively oldest, most favorable C-fraction, particularly a biologically inert C-fraction of the organic C-pool. Inclusion of C-14 dating in pedogenetic working concepts required soil profile date-scanning in order to reveal the age versus depth interdependence. (orig./HK) [de

  5. Hybrid van der Waals SnO/MoS2 Heterojunctions for Thermal and Optical Sensing Applications

    KAUST Repository

    Wang, Zhenwei

    2017-11-10

    Emerging van der Waals heterojunctions (vdWH) containing 2D materials have shown exciting functionalities that surpass those of traditional devices based on bulk materials. In this Communication, a report on the properties of a 2D sulfide/oxide hybrid vdWH based on n-type molybdenum disulfide (MoS2) and p-type tin monoxide (SnO) is presented, with promising rectification, thermal-sensing, and photosensing performance. Specifically, the hybrid SnO/MoS2 vdWH shows static rectification ratio of 2 × 102 with ideality factor of 2.3, and can operate at 100 Hz with good stability. The vdWH shows good temperature stability with reversible and reproducible current levels up to 110 °C, indicating its potential for thermal sensing applications. The sensitivity of current variation is calculated to be 0.0144 dec °C−1. Finally, maximum responsivity of 8.17 mA W−1 and external quantum efficiency of 2.14% have been achieved in photovoltaic measurements. The results suggest that MoS2–SnO hybrid vdWH are promising for various sensing applications.

  6. Sample processing procedures and radiocarbon dating

    International Nuclear Information System (INIS)

    Svetlik, Ivo; Tomaskova, Lenka; Dreslerova, Dagmar

    2010-01-01

    The article outlines radiocarbon dating routines and highlights the potential and limitations of this method. The author's institutions have been jointly running a conventional radiocarbon dating laboratory using the international CRL code. A procedure based on the synthesis of benzene is used. Small samples are sent abroad for dating because no AMS instrumentation is available in the Czech Republic so far. Our laboratory plans to introduce routines for the processing of milligram samples and preparation of graphitized targets for AMS

  7. Thermoluminescence dating of Indian archaeological sites

    International Nuclear Information System (INIS)

    Singhvi, A.K.; Sharma, Y.P.; Agrawal, D.P.

    1983-01-01

    In an attempt to provide a chronology for Indian archaeological sites, an extensive pottery dating programme was initiated during 1978-1979. So far we have provided a chronology for seven important Indian archaeological sites. The dated cultures include: 1) the Ochre Colour Ware culture, 2) the Pre-Harappan culture, 3) the megalithic culture and 4) the Painted Grey Ware culture. A complete survey of recently measured TL dates are presented in a model format similar to that used in Radiocarbon. (author)

  8. Isotropic Negative Thermal Expansion Metamaterials.

    Science.gov (United States)

    Wu, Lingling; Li, Bo; Zhou, Ji

    2016-07-13

    Negative thermal expansion materials are important and desirable in science and engineering applications. However, natural materials with isotropic negative thermal expansion are rare and usually unsatisfied in performance. Here, we propose a novel method to achieve two- and three-dimensional negative thermal expansion metamaterials via antichiral structures. The two-dimensional metamaterial is constructed with unit cells that combine bimaterial strips and antichiral structures, while the three-dimensional metamaterial is fabricated by a multimaterial 3D printing process. Both experimental and simulation results display isotropic negative thermal expansion property of the samples. The effective coefficient of negative thermal expansion of the proposed models is demonstrated to be dependent on the difference between the thermal expansion coefficient of the component materials, as well as on the circular node radius and the ligament length in the antichiral structures. The measured value of the linear negative thermal expansion coefficient of the three-dimensional sample is among the largest achieved in experiments to date. Our findings provide an easy and practical approach to obtaining materials with tunable negative thermal expansion on any scale.

  9. How AMS dating changed my life

    International Nuclear Information System (INIS)

    Spriggs, M.

    2001-01-01

    Accelerator mass spectrometry (AMS) radiocarbon dating was developed in the late 1970s. Remembering back to a time before AMS dating was available to archaeologists is a bit like trying to remember how we ever survived without desktop computers, email or automatic teller machines. My own particular interest in AMS dating was an inevitable offshoot from my long-established interest in chronometric hygiene, or 'getting the dates right'. In this paper I attempt to illustrate that accurate dating matters, by discussing some examples of AMS dating projects with which I have been involved over the last six years or so. In relation to these projects, AMS has given us the ability to date sites which we could not before. It has enabled us to provide more detailed stratigraphies when datable materials are rare. It has allowed us to date materials we could not date before, such as rock art pigments. It has been able to provide indications of the degree of site disturbance in the absence of other obvious forms of evidence. And it has allowed us to assess claims for the antiquity of particular material cultural types and faunal introductions. (author). 41 refs

  10. AMS Radiocarbon Dating at Notre Dame

    Science.gov (United States)

    Howard, Sean

    2014-09-01

    Current development of a local radiocarbon dating method using Accelerator Mass Spectrometry (AMS) at the University of Notre Dame seeks to provide sensitive, reproducible, and accurate measurements for future interdisciplinary projects. While AMS has been the premier radiocarbon dating method for a few decades, repurposing Notre Dame's FN Tandem accelerator for radiocarbon dating has provided many unique challenges. Experiments have shown radiocarbon dating possible and reproducible using the FN Tandem accelerator, found optimal settings for said accelerator, and established sensitivity limits comparable to dedicated radiocarbon dating facilities. In addition, there is ongoing work to create a local chemistry lab to convert organic artifacts into graphite samples to be dated locally. Once the chemistry side has been completed, several artifacts from the IAEA's radiocarbon intercomparison have been procured. Dating these previously studied artifacts will provide an additional measure on the accuracy and repeatability of both the accelerator and chemical treatment. Provided that these IAEA artifacts are dated successfully, exciting projects will ensue, such as the authentication of artwork and dating of anthropological samples.

  11. NERC radiocarbon dating: 1975-1985

    International Nuclear Information System (INIS)

    Bowen, D.Q.; Harkness, D.D.

    1986-06-01

    The paper reviews the work of the Natural Environment Research Council Radiocarbon Dating Laboratory in connection with Quaternary research, over the last decade. A description is given of the development of the dating service and in-house research. Quaternary research investigations aided by radiocarbon dating are described under the topic headings: The late Devensian glacial maximum, late glacial, middle Devensian, palaeomagnetic secular variation in lake sediments, vegetational history, faunal history, palaeolimnology, ground water, volcanology, periglacial research, palaoeohydrology, geomorphology, quaternary events in low-latitudes, environmental archaeology, archaeology, deep sea sediments, continental shelf, coastal geomorphology, and radiocarbon dating in Antarctica. (U.K.)

  12. Using microwaves in Disinsection of dates

    International Nuclear Information System (INIS)

    Zouba, Anis

    2008-01-01

    The date palm plays a very significant role in Tunisia in term of culture as well as social, economic and ecological aspects. The production of the dates which is estimated to 120.000 tons/year ensures the principal income for the majority of the oasis population of the South of Tunisia and constitutes the basis for agricultural, industrial, commercial and tourist activities, offering million of working days. The date palm is cultivated mainly for the production of dates which are consumed locally or also exported abroad but for its by-products (food of the cattle, wind breaks, fuel, construction) which are marketed and/ or used in the everyday life thus taking part in the sedentarisation of the populations and the maintenance of a fragile socio-economic balance. The date moth, Ectomyelois ceratoniae Zell. ( L will epidoptera, Pyralidae) is without question the most significant problem of the Tunisian date palm. The infestation of dates in the field and in the storage and packing houses enormously depreciates the marketable quality of dates and risk to compromise exports in particular those of the variety Deglet Nour. rates of infestations of about 20% are often recorded in Tunisia where as the European standards require rates lower than 5%. In Tunisia the desinsectisation of dates is done until now by the use of methyl bromide, its high toxicity substantially reduces the duration of date treatment, and consequently the treated volumes. The replacement of this product becomes an urgent need its use will not be authorized by 2015. Within the framework of a agreement between the Regional Research Center in Oasis Agriculture (CRRAO), The Interprofessional Grouping of Fruits (GIF), and the Italian Company IMETEC, the use one of micro-waves as a desinsectisation method of dates was evaluated. The results of this present work showed that total desinsectisation of dates by microwaves can be obtained only with homogeneous dates in term of water content. Total

  13. Towards dating Quaternary sediments using the quartz Violet Stimulated Luminescence (VSL) signal

    DEFF Research Database (Denmark)

    Ankjærgaard, C.; Jain, Mayank; Wallinga, J.

    2013-01-01

    Quaternary sediments using the violet (402 nm) stimulated luminescence (VSL) signal of quartz.We develop and test a new post-blue VSL single aliquot regenerative dose dating protocol, and demonstrate that the VSL signal originates from a deep trap at about 1.9 eV with a thermal lifetime of 1011 years at 10......Quartz optically stimulated luminescence (OSL) dating is widely used to determine the time of deposition and burial of Late Quaternary sediments. Application of the method is usually limited to the past 150,000 years due to early saturation of the OSL signal. Here we explore the potential to date...

  14. Fabrication and characterization of NiO based metal-insulator-metal diode using Langmuir-Blodgett method for high frequency rectification

    Science.gov (United States)

    Azad, Ibrahim; Ram, Manoj K.; Goswami, D. Yogi; Stefanakos, Elias

    2018-04-01

    Thin film metal-insulator-metal (MIM) diodes have attracted significant attention for use in infrared energy harvesting and detection applications. As demonstrated over the past decades, MIM or metal-insulator-insulator-metal (MIIM) diodes can operate at the THz frequencies range by quantum tunneling of electrons. The aim of this work is to synthesize required ultra-thin insulating layers and fabricate MIM diodes using the Langmuir-Blodgett (LB) technique. The nickel stearate (NiSt) LB precursor film was deposited on glass, silicon (Si), ITO glass and gold coated silicon substrates. The photodesorption (UV exposure) and the thermodesorption (annealing at 100 °C and 350 °C) methods were used to remove organic components from the NiSt LB film and to achieve a uniform homogenous nickel oxide (NiO) film. These ultrathin NiO films were characterized by EDS, AFM, FTIR and cyclic voltammetry methods, respectively. The MIM diode was fabricated by depositing nickel (Ni) on the NiO film, all on a gold (Au) plated silicon (Si) substrate. The current (I)-voltage (V) characteristics of the fabricated diode were studied to understand the conduction mechanism assumed to be tunneling of electron through the ultra-thin insulating layer. The sensitivity of the diode was measured to be as high as 35 V-1. The diode resistance was ˜100 ohms (at a bias voltage of 0.60 V), and the rectification ratio was about 22 (for a signal voltage of ±200 mV). At the bias point, the diode response demonstrated significant non-linearity and high asymmetry, which are very desirable characteristics for applications in infrared detection and harvesting.

  15. Fabrication and characterization of NiO based metal−insulator−metal diode using Langmuir-Blodgett method for high frequency rectification

    Directory of Open Access Journals (Sweden)

    Ibrahim Azad

    2018-04-01

    Full Text Available Thin film metal–insulator–metal (MIM diodes have attracted significant attention for use in infrared energy harvesting and detection applications. As demonstrated over the past decades, MIM or metal-insulator-insulator-metal (MIIM diodes can operate at the THz frequencies range by quantum tunneling of electrons. The aim of this work is to synthesize required ultra-thin insulating layers and fabricate MIM diodes using the Langmuir-Blodgett (LB technique. The nickel stearate (NiSt LB precursor film was deposited on glass, silicon (Si, ITO glass and gold coated silicon substrates. The photodesorption (UV exposure and the thermodesorption (annealing at 100 °C and 350 °C methods were used to remove organic components from the NiSt LB film and to achieve a uniform homogenous nickel oxide (NiO film. These ultrathin NiO films were characterized by EDS, AFM, FTIR and cyclic voltammetry methods, respectively. The MIM diode was fabricated by depositing nickel (Ni on the NiO film, all on a gold (Au plated silicon (Si substrate. The current (I-voltage (V characteristics of the fabricated diode were studied to understand the conduction mechanism assumed to be tunneling of electron through the ultra-thin insulating layer. The sensitivity of the diode was measured to be as high as 35 V-1. The diode resistance was ∼100 ohms (at a bias voltage of 0.60 V, and the rectification ratio was about 22 (for a signal voltage of ±200 mV. At the bias point, the diode response demonstrated significant non-linearity and high asymmetry, which are very desirable characteristics for applications in infrared detection and harvesting.

  16. Chromatographic separation of fructose from date syrup.

    Science.gov (United States)

    Al Eid, Salah M

    2006-01-01

    The objective of this study is to provide a process for separating fructose from a mixture of sugars containing essentially fructose and glucose, obtained from date palm fruits. The extraction procedure of date syrup from fresh dates gave a yield of 86.5% solids after vacuum drying. A process for separating fructose from an aqueous solution of date syrup involved adding the date syrup solutions (20, 30 and 40% by weight) to a chromatographic column filled with Dowex polystyrene strong cation exchange gel matrix resin Ca2 + and divinylbenzene, a functional group, sulfonic acid, particle size 320 microm, with a flow rate of 0.025 and 0.05 bed volume/min, under 30 and 70 degrees C column temperature. After the date sugar solution batch, a calculated quantity of water was added to the column. Glucose was retained by the resin more weakly than fructose and proceeded faster into the water batch flowing ahead. Three fractions were collected: a glucose-rich fraction, a return fraction, and a fructose-rich fraction. The return fraction is based on when the peaks of fructose and glucose were reached, which could be determined by means of an analyzer (polarimeter) based on the property of glucose and fructose solutions to turn the polarization level of polarized light. A high yield of fructose is obtained at 70 degrees C column temperature with a flow rate of 0.025 bed volume/min and date syrup solution containing 40% sugar concentration. The low recovery by weight obtained using date syrup solutions having a sugar concentration of 20 and 30%, encourages the use of a concentration of 40%. However, with the 40% date syrup supply the average concentrations of glucose and fructose in the return fractions were more than 40%, which can be used for diluting the thick date syrup solution extracted from dates.

  17. Archaeological and Geological dating by means of thermoluminescence

    International Nuclear Information System (INIS)

    Gonzalez M, P.R.

    1999-01-01

    In this thesis an specific method for dating local archaeological and geological samples based on the phenomenon of thermoluminescence (TL) using the fine grain and quartz inclusion techniques is developed. Taking into account that this work is interesting for professionals working in the fields of Physics, Chemistry, Archaeology, Anthropology and related sciences, some basic concepts are described to have a better comprehension. Chapter 1 describes the concept of radioactivity, remarking the importance of the different decay types as well as the main radioactive series and the energy liberated in the process. The causes of radioactive desequilibrium are also considered in the case for radon. Another important aspect taken into account in this chapter is the radioisotope production and its relationship with the neutron activation analysis used for the determination of the Uranium and Thorium concentrations in the samples. The TL phenomenon is described in Chapter 2, emphasizing the importance of the process of thermally stimulated luminescence best known as TL and its application for dating minerals of different origin. Chapter 3 shows some important antecedents remarking some aspects of the techniques commonly used for dating purposes. Chapter 4 shows the different methods used for the sample preparation. The techniques used for the 40 K, 238 U and 232 Th determination as well as for the cosmic radiation measurement using locally made TLD are also described. The methods used for the determination of the paleodosis as a function of the TL intensity of each sample are described: special emphasis is taken on the moisture effects as well as in the error limits in the age estimation. Results and conclusions of this study are presented in Chapter 5. These results gave an age of 980 ± 90 years for the Edzna ceramic and 1520 ± 90 years for the Calixtlahuaca ceramics. The age of the Teotihuacan ceramics was not estimated due to the lack of a stable region of the traps

  18. 75 FR 57252 - Designated Transfer Date

    Science.gov (United States)

    2010-09-20

    ..., as the date for the transfer of functions to the Bureau of Consumer Financial Protection (``CFPB... other laws. After consulting with the heads of the agencies whose functions will transfer to the CFPB... July 21, 2011, as the transfer date will advance the mission of the CFPB and promote an orderly and...

  19. 12 CFR 563g.6 - Effective date.

    Science.gov (United States)

    2010-01-01

    ... 12 Banks and Banking 5 2010-01-01 2010-01-01 false Effective date. 563g.6 Section 563g.6 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY SECURITIES OFFERINGS § 563g.6 Effective date. (a) Except as provided for in paragraph (d) of this section, an offering circular filed by a...

  20. 40 CFR 425.05 - Compliance dates.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Compliance dates. 425.05 Section 425.05 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS LEATHER TANNING AND FINISHING POINT SOURCE CATEGORY General Provisions § 425.05 Compliance dates...

  1. Jealousy during Dating among Female College Students

    Science.gov (United States)

    Khanchandani, Laveena; Durham, Thomas W.

    2009-01-01

    This study examined the relationship between several situational and personality variables and jealousy in dating relationships among 100 college women volunteers who completed a series of questionnaires about themselves and their dating situations. Six research questions were examined. Results showed that jealousy was lower for women in a steady…

  2. 21 CFR 211.137 - Expiration dating.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Expiration dating. 211.137 Section 211.137 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) DRUGS... § 211.137 Expiration dating. (a) To assure that a drug product meets applicable standards of identity...

  3. ESR dating of marine fossil shells

    International Nuclear Information System (INIS)

    Radtke, U.; Mangini, A.; Gruen, R.

    1985-01-01

    In order to establish the relatively new ESR dating method for marine shells a detailed comparison with the independent U-series technique was carried out. Agreement of both dating methods with the geological classification is strongly dependent on the species investigated and environmental conditions. Several problems encountered in the determination of the accumulated dose as well as the annual dose are discussed. (author)

  4. ESR dating of marine fossil shells

    Energy Technology Data Exchange (ETDEWEB)

    Radtke, U; Mangini, A; Gruen, R

    1985-01-01

    In order to establish the relatively new ESR dating method for marine shells a detailed comparison with the independent U-series technique was carried out. Agreement of both dating methods with the geological classification is strongly dependent on the species investigated and environmental conditions. Several problems encountered in the determination of the accumulated dose as well as the annual dose are discussed.

  5. 16 CFR 314.5 - Effective date.

    Science.gov (United States)

    2010-01-01

    ... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Effective date. 314.5 Section 314.5 Commercial Practices FEDERAL TRADE COMMISSION REGULATIONS UNDER SPECIFIC ACTS OF CONGRESS STANDARDS FOR SAFEGUARDING CUSTOMER INFORMATION § 314.5 Effective date. (a) Each financial institution subject to the...

  6. 7 CFR 1421.101 - Maturity dates.

    Science.gov (United States)

    2010-01-01

    ... filed and disbursed except, for transferred marketing assistance loan collateral. The maturity date for transferred marketing assistance loan collateral will be the maturity date applicable to the original loan... AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS GRAINS AND SIMILARLY HANDLED COMMODITIES-MARKETING...

  7. Dating violence and suicidal behavior in adolescents.

    Science.gov (United States)

    Holmes, Kristin; Sher, Leo

    2013-01-01

    The aim of this paper is to assess the possible consequences of adolescent physical, emotional and sexual dating violence through a review of the literature on the topic. An electronic search of major biomedical bibliographic databases (Pubmed, ISI, PsycINFO) was used to retrieve articles providing information on the prevalence rates, risk factors, associated consequences and possible preventive measures for adolescent dating violence across different populations. Currently, there have been few longitudinal studies conducted to identify potential risk factors for entering a violent dating relationship in adolescence. Risky behaviors such as early sexual intercourse may predispose someone for victimization. Dating violence itself is also a predictor of future dating violence. Adolescent dating violence was associated with an increase in other violence-related behaviors, substance use, depression, poorer educational outcomes, posttraumatic stress, unhealthy weight control and risky sexual behavior. The association between adolescent dating violence and an increase in suicidal behavior is a major public health concern. Future research should focus on longitudinal studies so that a causal relationship between dating violence and suicidality may be better understood.

  8. Peer Involvement in Adolescent Dating Violence

    Science.gov (United States)

    Stephenson, Pam S.; Martsolf, Donna; Draucker, Claire Burke

    2013-01-01

    This study investigated the ways in which peers are involved in adolescent dating violence. Eighty-eight young adults aged 18-21 were interviewed and asked to reflect on aggressive dating relationships they experienced as teens. The researchers used grounded theory to analyze the data. Findings showed that male and female peers were involved in…

  9. Teen Dating Violence Prevention Program Assessment

    Science.gov (United States)

    Lucas, Quincy Arrianna Rose

    2013-01-01

    The American Psychological Association (APA) has identified the prevention of and intervention in relationship violence as a top priority (APA, n.d.). According to the Center for Disease Control and Prevention's 2012 Teen Dating Violence Fact Sheet, dating violence is a serious problem in the United States. In accordance with Foshee et al. (1998):…

  10. 46 CFR 308.552 - Effective date.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 8 2010-10-01 2010-10-01 false Effective date. 308.552 Section 308.552 Shipping... Cargo Insurance Iv-General § 308.552 Effective date. This subpart shall be effective as and when the... commerce of the United States cannot be obtained on reasonable terms and conditions from companies...

  11. 38 CFR 3.54 - Marriage dates.

    Science.gov (United States)

    2010-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Marriage dates. 3.54..., Compensation, and Dependency and Indemnity Compensation Relationship § 3.54 Marriage dates. A surviving spouse may qualify for pension, compensation, or dependency and indemnity compensation if the marriage to the...

  12. Thermal expansion

    International Nuclear Information System (INIS)

    Yun, Y.

    2015-01-01

    Thermal expansion of fuel pellet is an important property which limits the lifetime of the fuels in reactors, because it affects both the pellet and cladding mechanical interaction and the gap conductivity. By fitting a number of available measured data, recommended equations have been presented and successfully used to estimate thermal expansion coefficient of the nuclear fuel pellet. However, due to large scatter of the measured data, non-consensus data have been omitted in formulating the equations. Also, the equation is strongly governed by the lack of appropriate experimental data. For those reasons, it is important to develop theoretical methodologies to better describe thermal expansion behaviour of nuclear fuel. In particular, first-principles and molecular dynamics simulations have been certainly contributed to predict reliable thermal expansion without fitting the measured data. Furthermore, the two theoretical techniques have improved on understanding the change of fuel dimension by describing the atomic-scale processes associated with lattice expansion in the fuels. (author)

  13. Ambiguity and violence in adolescent dating relationships.

    Science.gov (United States)

    Draucker, Claire Burke; Martsolf, Donna; Stephenson, Pam Shockey

    2012-08-01

    Little is known about dyadic processes that lead to adolescent dating violence. The purpose of this study was to examine the phenomenon of relationship ambiguity in adolescent dating relationships to better understand how ambiguity contributes to violence and aggression between dating partners. Data were drawn from 88 narratives of young adults who had participated in a study on adolescent dating violence. Interpretive phenomenology was used to produce an in-depth description of the phenomenon of relationship ambiguity. Relationship ambiguity results in differing expectations between partners regarding closeness and intimacy, fidelity, and obligation. These differences lead to conflicts that set the stage for violence and aggression in adolescent dating relationships. A series of recommendations for clinicians working with adolescents are presented. © 2012 Wiley Periodicals, Inc.

  14. Record date in Serbian company law

    Directory of Open Access Journals (Sweden)

    Arsić Zoran

    2011-01-01

    Full Text Available The right of the shareholder to participate in and vote at the general meeting is determined based on the shares he holds on a certain date prior to the general meeting (record date. However, the rules regulating the record date deviate from the principle of indivisibility of shares. In extreme cases it is possible to have persons, none of which are shareholders at a given time, to participate in and vote at the general meeting. Hence, it is possible to have persons with no investment interest in the company to decide, for example, on adoption of financial reports, or on disposal of high-value assets. This issue, by its virtue, is not put forward in cases where there was no transfer of shares in the period between the record date and the date of the general meeting.

  15. U-Th-He dating of apatite: A potential thermochronometer

    International Nuclear Information System (INIS)

    Zeitler, P.K.; Herczeg, A.L.; McDougall, I.; Honda, M.

    1987-01-01

    The authors found a gem quality crystal of Durango fluorapatite to have a 4 He content consistent with complete retention of radiogenic helium since its formation at about 31 Ma. Isothermal heating and step-heating analysis reveal 4 He loss to occur systematically by volume diffusion at low temperatures. The linear, low-temperature portion of the diffusion data yields an activation energy of 38.5 ± 8.1 kcal/mol and a frequency factor of 1n (D 0 /a 2 ) = 16.4 ± 2.8 sec -1 , corresponding to a closure temperature of 105 degree C ± 30 degree C (cooling rate 10 degree C/m.y.). It appears that U-Th-He dating of apatite might represent a useful new thermochronometer with a range similar to that of fission-track dating of apatite. From these results, they infer that a number of the too-young U-Th-He dates reported in the literature on minerals such as zircon and magnetite may in fact represent valuable records of the low-temperature thermal history of their host rocks

  16. Meshed doped silicon photonic crystals for manipulating near-field thermal radiation

    Science.gov (United States)

    Elzouka, Mahmoud; Ndao, Sidy

    2018-01-01

    The ability to control and manipulate heat flow is of great interest to thermal management and thermal logic and memory devices. Particularly, near-field thermal radiation presents a unique opportunity to enhance heat transfer while being able to tailor its characteristics (e.g., spectral selectivity). However, achieving nanometric gaps, necessary for near-field, has been and remains a formidable challenge. Here, we demonstrate significant enhancement of the near-field heat transfer through meshed photonic crystals with separation gaps above 0.5 μm. Using a first-principle method, we investigate the meshed photonic structures numerically via finite-difference time-domain technique (FDTD) along with the Langevin approach. Results for doped-silicon meshed structures show significant enhancement in heat transfer; 26 times over the non-meshed corrugated structures. This is especially important for thermal management and thermal rectification applications. The results also support the premise that thermal radiation at micro scale is a bulk (rather than a surface) phenomenon; the increase in heat transfer between two meshed-corrugated surfaces compared to the flat surface (8.2) wasn't proportional to the increase in the surface area due to the corrugations (9). Results were further validated through good agreements between the resonant modes predicted from the dispersion relation (calculated using a finite-element method), and transmission factors (calculated from FDTD).

  17. Lightweight Thermally Stable Multi-Meter Aperture Submillimeter Reflectors, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Future astrophysics missions will require lightweight, thermally stable, submillimeter reflectors in sizes of 4m and greater. To date, graphite fiber reinforced...

  18. 12 CFR 41.28 - Effective date, compliance date, and prospective application.

    Science.gov (United States)

    2010-01-01

    ... TREASURY FAIR CREDIT REPORTING Affiliate Marketing § 41.28 Effective date, compliance date, and prospective... an affiliate to make solicitations to a consumer if the bank receives such information prior to...

  19. 16 CFR 680.28 - Effective date, compliance date, and prospective application.

    Science.gov (United States)

    2010-01-01

    ... REPORTING ACT AFFILIATE MARKETING § 680.28 Effective date, compliance date, and prospective application. (a... part shall not prohibit you from using eligibility information that you receive from an affiliate to...

  20. 12 CFR 571.28 - Effective date, compliance date, and prospective application.

    Science.gov (United States)

    2010-01-01

    ... THE TREASURY FAIR CREDIT REPORTING Affiliate Marketing § 571.28 Effective date, compliance date, and... receive from an affiliate to make solicitations to a consumer if you receive such information prior to...

  1. Thermal Properties and Thermal Analysis:

    Science.gov (United States)

    Kasap, Safa; Tonchev, Dan

    The chapter provides a summary of the fundamental concepts that are needed to understand the heat capacity C P, thermal conductivity κ, and thermal expansion coefficient α L of materials. The C P, κ, and α of various classes of materials, namely, semiconductors, polymers, and glasses, are reviewed, and various typical characteristics are summarized. A key concept in crystalline solids is the Debye theory of the heat capacity, which has been widely used for many decades for calculating the C P of crystals. The thermal properties are interrelated through Grüneisen's theorem. Various useful empirical rules for calculating C P and κ have been used, some of which are summarized. Conventional differential scanning calorimetry (DSC) is a powerful and convenient thermal analysis technique that allows various important physical and chemical transformations, such as the glass transition, crystallization, oxidation, melting etc. to be studied. DSC can also be used to obtain information on the kinetics of the transformations, and some of these thermal analysis techniques are summarized. Temperature-modulated DSC, TMDSC, is a relatively recent innovation in which the sample temperature is ramped slowly and, at the same time, sinusoidally modulated. TMDSC has a number of distinct advantages compared with the conventional DSC since it measures the complex heat capacity. For example, the glass-transition temperature T g measured by TMDSC has almost no dependence on the thermal history, and corresponds to an almost step life change in C P. The new Tzero DSC has an additional thermocouple to calibrate better for thermal lags inherent in the DSC measurement, and allows more accurate thermal analysis.

  2. Longitudinal relationships between individual and class norms supporting dating violence and perpetration of dating violence.

    Science.gov (United States)

    Taylor, Katherine A; Sullivan, Terri N; Farrell, Albert D

    2015-03-01

    Dating violence is commonly perpetrated in adolescence, making it imperative to understand risk factors in order to inform prevention efforts. Although individual norms supporting dating violence are strongly related to its perpetration, few studies have examined their longitudinal impact. Moreover, the influence of class norms (i.e., norms for students in the same grade, cohort, and school) supporting dating violence on perpetration has rarely been studied. The current study examined longitudinal relationships between individual and class norms supporting dating violence and perpetration of physical and psychological dating violence. Participants were two cohorts of sixth graders from 37 schools who were in dating relationships at Wave 1 and 6 months later at Wave 2 (N = 2,022; 43% female; 52% African American, 21% Latino/a, 20% White, and 7% other). The analyses used a multilevel approach, with students represented at Level 1 and classes (n = 74) at Level 2. The models tested direct effects of Wave 1 individual and class norms supporting dating violence on subsequent changes in perpetration of dating violence at Wave 2 and the extent to which gender moderated these relationships. The findings indicated that greater individual norms supporting male dating violence predicted greater change in perpetration of physical and psychological dating violence and greater individual norms supporting female dating violence predicted greater change in perpetration of psychological dating violence. Greater class norms supporting male dating violence predicted greater change in perpetration of physical dating violence; whereas greater class norms supporting female dating violence predicted less change in perpetration of physical dating violence. These findings highlight the need to address norms in early adolescence.

  3. Dating of fossil hominid: problems and perspectives

    International Nuclear Information System (INIS)

    Poupeau, G.; Danon, J.; Baksi, A.K.

    1984-01-01

    The hominid dating anterior to the Homo Erectus has been based up to now on the rocks and minerals geochronology of vulcanic origem in stratigraphic relation with the fossils. Two methods are widely used, potassium-argon and uranium fission track dating. The vulcanic material dating; lava, lephra, associated with the hominid leavings show big difficults essentially connected to several types of contamination and modification. Two available examples inside the east-african rift show the probelms linked to these dating. The current progresses in the dating methods can contribute by one hand to a better utilization of the K-Ar and fisson track methods for the vulcanic materials. By other hand, with the introduction of new dating methods (thermoluminescence and electron paramagnetic resonance) will be possible to date directly whether the fossil bone itself or the associated sedimentar material. This open new perspectives in particular for every sites which are not inter-stratified with the vulcanic material. (L.C.) [pt

  4. Validating post IR-IRSL dating on K-feldspars through comparison with quartz OSL ages

    NARCIS (Netherlands)

    Kars, R.H.; Busschers, F.S.; Wallinga, J.

    2012-01-01

    Recent developments have opened up the possibilities of using potassium feldspar for dating Pleistocene sediments; a stable (less-fading) part of the infrared stimulated luminescence (IRSL) signal can be selected by largely depleting the unstable part of the IR signal, using a combination of thermal

  5. Testing the application of quartz and feldspar luminescence dating to MIS 5 Japanese marine deposits

    DEFF Research Database (Denmark)

    Thiel, Christine; Tsukamoto, Sumiko; Tokuyasu, Kayoko

    2015-01-01

    The applicability of both quartz and feldspar luminescence dating was tested on twenty-five samples from a marine succession now forming a coastal cliff at Oga Peninsula, Honshu Island, Japan. The quartz optically stimulated luminescence (OSL) signal shows thermal instability and linear modulated...

  6. A Phenomenological Investigation of Adolescent Dating Relationships and Dating Violence Counseling Interventions

    Science.gov (United States)

    Hays, Danica G.; Michel, Rebecca E.; Cole, Rebekah F.; Emelianchik, Kelly; Forman, Julia; Lorelle, Sonya; McBride, Rebecca; Sikes, April

    2011-01-01

    Despite the prevalence of dating violence, incidences often go unreported due to a lack of awareness among students as to appropriate dating behaviors. This phenomenology investigated how adolescents conceptualize and experience dating relationships. We explored adolescent females' definitions of healthy and abusive relationships, experiences with…

  7. 20 CFR 404.630 - Use of date of written statement as filing date.

    Science.gov (United States)

    2010-04-01

    ... data on the Internet Social Security Benefit Application to us, we will use the date of the... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Use of date of written statement as filing date. 404.630 Section 404.630 Employees' Benefits SOCIAL SECURITY ADMINISTRATION FEDERAL OLD-AGE...

  8. Development of thermoluminescence dating techniques at Oxford

    International Nuclear Information System (INIS)

    Fleming, S.J.

    1977-01-01

    The two-decade long history of thermoluminescene as a pottery dating method is surveyed with particular reference to the various problems that have been encountered in the Oxford Laboratory's research programme. Effects, such as supralinearity and radon emanation, are explained in terms of how they are measured and how their existence influences thermoluminescence (TL) dating accuracy (currently close to plus minus 7% per analysis). Illustrations of Thermoluminescence (TL) applications include a Nok culture terracotta from Nigeria and a Cambodia bronze Buddha figure of the Khmer period, dated ising the ceramic-like casting-core retained within it. (author)

  9. ESR dating of tooth enamel samples

    International Nuclear Information System (INIS)

    Chen Tiemei; Yang quan; Wu En

    1993-01-01

    Five tooth samples from the palaeoanthropological site of Jinniushan were dated with both electron-spin-resonance (ESR) and uranium-series techniques. The ESR age of about 230 ka is in good agreement with the U-series dating result, which confirms the hypothesis of possible coexistence of Homo erect us and Homo sapiens in China. Problems in ESR dating are discussed such as: 1) inappropriate of simple exponential extrapolation for accumulated dose determination; 2)experimental measurement of alpha detection efficiency and radon emanation and 3)selection of U-uptake model

  10. Some wholesomeness studies on irradiated Iraqi dates

    International Nuclear Information System (INIS)

    Al Rawi, A.M.; Hamoudi, H.I.

    1981-01-01

    Iraqi dates (Zahdi and Khestawi) were irradiated at different dose levels (0 to 1500 krad) to extend their shelf-lives. Samples irradiated at 150 krad showed no change in the behaviour studies of tested Swiss albino mice. Fungi were found to have a constant rate of growth on the syrup irradiated dates. Chemical products such as malondialdehyde, deoxy sugars, acids and reducing sugars were quantified. In conclusion, 150 krad is a convenient dose to extend the shelf-lives of the tested dates and is therefore recommended. (author)

  11. Optically stimulated luminescence dating of young sediments

    DEFF Research Database (Denmark)

    Madsen, Anni Tindahl; Murray, Andrew S.

    2009-01-01

    of OSL dating, outlines the problems specific to the dating of young material, and then uses recent applications to young sediments to illustrate the greatly increased scope and potential of the method in geomorphology and the geology of recent deposits. The overall reliability of this new generation...... for determining the time of deposition of water-lain sediments from the coastal zone, and aeolian deposits from both coastal and inland environments. Our conclusion is supported by the growing popularity of OSL dating in geomorphology and geology...

  12. TL and EPR dating: some applications

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, S. [Institute of Physics, University of Sao Paulo, Sao Paulo (Brazil)

    2006-07-01

    The intensity of thermoluminescence light emitted by a crystal is a function of radiation dose. The number of defects or of radicals in a crystal or organic substances is also a function of radiation dose. Since such defects or radicals present EPR signals, the EPR intensity is also a function of radiation dose. These facts are basis for radiation dosimetry and can be applied in dating of archaeological potteries or other materials, as well as in dating geological substances such as sediments, caves speleothemes, animal teeth and bones. Recent investigation on sensitized quartz based dosimeters and dating calcite covering ancient wall painting to find early settlers in Brazil will be presented. (Author)

  13. Annual radiation dose in thermoluminescence dating

    International Nuclear Information System (INIS)

    Li Huhou

    1988-01-01

    The annual radiation dose in thermoluminescence dating has been discussed. The autor gives an entirely new concept of the enviromental radiation in the thermoluminescence dating. Methods of annual dose detemination used by author are dating. Methods of annual dose determination used by author are summed up, and the results of different methods are compared. The emanium escapiug of three radioactive decay serieses in nature has been considered, and several determination methods are described. The contribution of cosmic rays for the annual radiation dose has been mentioned

  14. Annual radiation dose in thermoluminescence dating

    Energy Technology Data Exchange (ETDEWEB)

    Huhou, Li [Chinese Academy of Social Sciences, Beijing, BJ (China). Inst. of Archaeology

    1988-11-01

    The annual radiation dose in thermoluminescence dating has been discussed. The autor gives an entirely new concept of the enviromental radiation in the thermoluminescence dating. Methods of annual dose detemination used by author are dating. Methods of annual dose determination used by author are summed up, and the results of different methods are compared. The emanium escapiug of three radioactive decay serieses in nature has been considered, and several determination methods are described. The contribution of cosmic rays for the annual radiation dose has been mentioned.

  15. Thermal comfort

    DEFF Research Database (Denmark)

    d’Ambrosio Alfano, Francesca Romana; Olesen, Bjarne W.; Palella, Boris Igor

    2014-01-01

    Thermal comfort is one of the most important aspects of the indoor environmental quality due to its effects on well-being, people's performance and building energy requirements. Its attainment is not an easy task requiring advanced design and operation of building and HVAC systems, taking...... into account all parameters involved. Even though thermal comfort fundamentals are consolidated topics for more than forty years, often designers seem to ignore or apply them in a wrong way. Design input values from standards are often considered as universal values rather than recommended values to be used...... under specific conditions. At operation level, only few variables are taken into account with unpredictable effects on the assessment of comfort indices. In this paper, the main criteria for the design and assessment of thermal comfort are discussed in order to help building and HVAC systems designers...

  16. Amtrak's strategic business plan : progress to date

    Science.gov (United States)

    1996-07-24

    To address its financial crisis and make its operations more efficient, in 1995 : Amtrak undertook a major corporate restructuring, along with developing its : Strategic Business Plan. This report (1) reviews Amtrak's success to date in : achieving f...

  17. Potassium-argon dating in archaeology

    Energy Technology Data Exchange (ETDEWEB)

    McDougall, I. (Australian National Univ., Canberra (Australia). Research School of Earth Sciences)

    1990-01-01

    The potassium-argon (K-Ar) isotopic dating method can provide precise and accurate numerical ages on suitable rocks, especially igneous rocks, over a wide range of age from less than 100,000 years old, with no older limit. Together with its variants, the {sup 40}Ar/{sup 39}Ar technique, the K-Ar method is very useful for the numerical age calibration of stratigraphic sequences, including those containing archaeological or fossil material, in cases where appropriate rocks for dating are present. This brief review of the basis of the K-Ar dating method and the underlying assumptions, concludes with an example of its application to the Plio-Pleistocene stratigraphic sequence in the Turkana Basin, northern Kenya. By dating alkali feldspars separated from pumice blocks in tuffaceous beds, excellent age control has been obtained for the wealth of vertebrate fossils, including hominids, as well as archaeological materials that has been found in the sequence. (author).

  18. Coconut, date and oil palm genomics

    Science.gov (United States)

    A review of genomics research is presented for the three most economically important palm crops, coconut (Cocos nucifera), date palm (Phoenix dactylifera) and oil palm (Elaeis guineensis), encompassing molecular markers studies of genetic diversity, genetic mapping, quantitative trait loci discovery...

  19. Bullying: a stepping stone to dating aggression?

    Science.gov (United States)

    Josephson, Wendy L; Pepler, Debra

    2012-01-01

    Bullying is the use of power and aggression to control and distress another. In this paper, we review research to explore whether the lessons learned in bullying provide a stepping stone to aggressive behavior in dating relationships. We start by considering definitions and a relationship framework with which to understand both bullying and dating aggression. We consider bullying from a developmental-contextual perspective and consider risk factors associated with the typical developmental patterns for bullying and dating aggression, including developmental and sociodemographic, individual attributes, and family, peer group, community, and societal relationship contexts that might lead some children and youths to follow developmental pathways that lead to bullying and dating aggression. We conclude by discussing implications for intervention with a review of evidence-based interventions.

  20. 38 CFR 21.4135 - Discontinuance dates.

    Science.gov (United States)

    2010-07-01

    ... not leading to a standard college degree is not timely received, payments will be terminated date of... withdraws from correspondence, flight, farm cooperative, cooperative or job training, benefits will be...

  1. Matrix thermalization

    International Nuclear Information System (INIS)

    Craps, Ben; Evnin, Oleg; Nguyen, Kévin

    2017-01-01

    Matrix quantum mechanics offers an attractive environment for discussing gravitational holography, in which both sides of the holographic duality are well-defined. Similarly to higher-dimensional implementations of holography, collapsing shell solutions in the gravitational bulk correspond in this setting to thermalization processes in the dual quantum mechanical theory. We construct an explicit, fully nonlinear supergravity solution describing a generic collapsing dilaton shell, specify the holographic renormalization prescriptions necessary for computing the relevant boundary observables, and apply them to evaluating thermalizing two-point correlation functions in the dual matrix theory.

  2. Matrix thermalization

    Science.gov (United States)

    Craps, Ben; Evnin, Oleg; Nguyen, Kévin

    2017-02-01

    Matrix quantum mechanics offers an attractive environment for discussing gravitational holography, in which both sides of the holographic duality are well-defined. Similarly to higher-dimensional implementations of holography, collapsing shell solutions in the gravitational bulk correspond in this setting to thermalization processes in the dual quantum mechanical theory. We construct an explicit, fully nonlinear supergravity solution describing a generic collapsing dilaton shell, specify the holographic renormalization prescriptions necessary for computing the relevant boundary observables, and apply them to evaluating thermalizing two-point correlation functions in the dual matrix theory.

  3. Matrix thermalization

    Energy Technology Data Exchange (ETDEWEB)

    Craps, Ben [Theoretische Natuurkunde, Vrije Universiteit Brussel (VUB), and International Solvay Institutes, Pleinlaan 2, B-1050 Brussels (Belgium); Evnin, Oleg [Department of Physics, Faculty of Science, Chulalongkorn University, Thanon Phayathai, Pathumwan, Bangkok 10330 (Thailand); Theoretische Natuurkunde, Vrije Universiteit Brussel (VUB), and International Solvay Institutes, Pleinlaan 2, B-1050 Brussels (Belgium); Nguyen, Kévin [Theoretische Natuurkunde, Vrije Universiteit Brussel (VUB), and International Solvay Institutes, Pleinlaan 2, B-1050 Brussels (Belgium)

    2017-02-08

    Matrix quantum mechanics offers an attractive environment for discussing gravitational holography, in which both sides of the holographic duality are well-defined. Similarly to higher-dimensional implementations of holography, collapsing shell solutions in the gravitational bulk correspond in this setting to thermalization processes in the dual quantum mechanical theory. We construct an explicit, fully nonlinear supergravity solution describing a generic collapsing dilaton shell, specify the holographic renormalization prescriptions necessary for computing the relevant boundary observables, and apply them to evaluating thermalizing two-point correlation functions in the dual matrix theory.

  4. Chlorine-36 dating of continental evaporites

    International Nuclear Information System (INIS)

    Huang Qi

    1990-01-01

    Teh chloring-36 production, principle and experimental method of 36 Cl dating are briefly described. The ages calculated from the 36 Cl/Cl ratios are generally concordant with those obtained by using 14 C, 230 Th and magnetostratigraphic techniques. It confirms the constancy of the chlorine input ratio over the last million years and implys that 36 Cl can provide accurate dates on continental saline sediments

  5. Reduction of date microbial load with ozone

    Science.gov (United States)

    Farajzadeh, Davood; Qorbanpoor, Ali; Rafati, Hasan; Isfeedvajani, Mohsen Saberi

    2013-01-01

    Background: Date is one of the foodstuffs that are produced in tropical areas and used worldwide. Conventionally, methyl bromide and phosphine are used for date disinfection. The toxic side effects of these usual disinfectants have led food scientists to consider safer agents such as ozone for disinfection, because food safety is a top priority. The present study was performed to investigate the possibility of replacing common conventional disinfectants with ozone for date disinfection and microbial load reduction. Materials and Methods: In this experimental study, date samples were ozonized for 3 and 5 hours with 5 and 10 g/h concentrations and packed. Ozonized samples were divided into two groups and kept in an incubator which was maintained at 25°C and 40°C for 9 months. During this period, every 3 month, microbial load (bacteria, mold, and yeast) were examined in ozonized and non-ozonized samples. Results: This study showed that ozonization with 5 g/h for 3 hours, 5 g/h for 5 hours, 10 g/h for 3 hours, and 10 g/h for 5 hours leads to about 25%, 25%, 53%, and 46% reduction in date mold and yeast load and about 6%, 9%, 76%, and 74.7% reduction in date bacterial load at baseline phase, respectively. Appropriate concentration and duration of ozonization for microbial load reduction were 10 g/h and 3 hours. Conclusion: Date ozonization is an appropriate method for microbial load reduction and leads to an increase in the shelf life of dates. PMID:24124432

  6. REPORT ON THE DATING THE ODYSSEY

    OpenAIRE

    r.e. Schmid

    2012-01-01

    STUDY SUPPORTS ACCURACY OF GREEK POET HOMER, SETS DATE FOR ODYSSEUS’ RETURN FROM TROJAN WAR

    Using clues from star and sun positions mentioned by the ancient Greek poet Homer, scholars think they have determined the date when King Odysseus returned from the Trojan War and slaughtered a group of suitors who had been pressing his wife to marry one of them.

  7. Correction procedures for C-14 dates

    International Nuclear Information System (INIS)

    McKerrell, H.

    1975-01-01

    There are two quite separate criteria to satisfy before accepting as valid the corrections to C-14 dates which have been indicated for some years now by the bristlecone pine calibration. Firstly the correction figures have to be based upon all the available tree-ring data and derived in a manner that is mathematically sound, and secondly the correction figures have to produce accurate results on C-14 dates from archaeological test samples of known historical date, these covering as wide a period as possible. Neither of these basic prerequisites has yet been fully met. Thus the two-fold purpose of this paper is to bring together, and to compare with an independently based procedure, the various correction curves or tables that have been published up to Spring 1974, as well as to detail the correction results on reliable, historically dated Egyptian, Helladic and Minoan test samples from 3100 B.C. The nomenclature followed is strictly that adopted by the primary dating journal Radiocarbon, all C-14 dates quoted thus relate to the 5568 year half-life and the standard AD/BC system. (author)

  8. Concentrating solar thermal power.

    Science.gov (United States)

    Müller-Steinhagen, Hans

    2013-08-13

    In addition to wind and photovoltaic power, concentrating solar thermal power (CSP) will make a major contribution to electricity provision from renewable energies. Drawing on almost 30 years of operational experience in the multi-megawatt range, CSP is now a proven technology with a reliable cost and performance record. In conjunction with thermal energy storage, electricity can be provided according to demand. To date, solar thermal power plants with a total capacity of 1.3 GW are in operation worldwide, with an additional 2.3 GW under construction and 31.7 GW in advanced planning stage. Depending on the concentration factors, temperatures up to 1000°C can be reached to produce saturated or superheated steam for steam turbine cycles or compressed hot gas for gas turbine cycles. The heat rejected from these thermodynamic cycles can be used for sea water desalination, process heat and centralized provision of chilled water. While electricity generation from CSP plants is still more expensive than from wind turbines or photovoltaic panels, its independence from fluctuations and daily variation of wind speed and solar radiation provides it with a higher value. To become competitive with mid-load electricity from conventional power plants within the next 10-15 years, mass production of components, increased plant size and planning/operating experience will be accompanied by technological innovations. On 30 October 2009, a number of major industrial companies joined forces to establish the so-called DESERTEC Industry Initiative, which aims at providing by 2050 15 per cent of European electricity from renewable energy sources in North Africa, while at the same time securing energy, water, income and employment for this region. Solar thermal power plants are in the heart of this concept.

  9. Mechanism of rectification and two-type bipolar resistance switching behaviors of Pt /Pb(Zr0.52Ti0.48)O3 /Nb:SrTiO3

    Science.gov (United States)

    Liu, W. W.; Jia, C. H.; Zhang, Q.; Zhang, W. F.

    2015-12-01

    Epitaxial Pb(Zr0.52Ti0.48)O3 (PZT) films have been grown on Nb:SrTiO3 (NSTO) (1 0 0) substrates. The films are a tetragonal perovskite phase with good density and homogeneity. Rectification behavior and two types of bipolar resistance switching (BRS) have been observed in the Pt/PZT/NSTO device. It exhibits rectification below 3 V. According to piezo force microscopy analysis, PZT film has a multidomain structure below 8 V and the device shows abnormal BRS between 3 V and 8 V. When the voltage increases above 8 V, the polarization of the PZT film tends to saturation and it becomes single domain and displays normal BRS behavior. In addition, the device demonstrates good retention and anti-fatigue properties. The transition from abnormal bipolar to normal bipolar behavior caused by ferroelectric polarization can broaden device applications and enable large flexibility in terms of memory architecture.

  10. Mechanism of rectification and two-type bipolar resistance switching behaviors of Pt /Pb(Zr0.52Ti0.48)O3 /Nb:SrTiO3

    International Nuclear Information System (INIS)

    Liu, W W; Jia, C H; Zhang, Q; Zhang, W F

    2015-01-01

    Epitaxial Pb(Zr 0.52 Ti 0.48 )O 3 (PZT) films have been grown on Nb:SrTiO 3 (NSTO) (1 0 0) substrates. The films are a tetragonal perovskite phase with good density and homogeneity. Rectification behavior and two types of bipolar resistance switching (BRS) have been observed in the Pt/PZT/NSTO device. It exhibits rectification below 3 V. According to piezo force microscopy analysis, PZT film has a multidomain structure below 8 V and the device shows abnormal BRS between 3 V and 8 V. When the voltage increases above 8 V, the polarization of the PZT film tends to saturation and it becomes single domain and displays normal BRS behavior. In addition, the device demonstrates good retention and anti-fatigue properties. The transition from abnormal bipolar to normal bipolar behavior caused by ferroelectric polarization can broaden device applications and enable large flexibility in terms of memory architecture. (paper)

  11. The contribution of radio-frequency rectification to field-aligned losses of high-harmonic fast wave power to the divertor in the National Spherical Torus eXperiment

    Energy Technology Data Exchange (ETDEWEB)

    Perkins, R. J., E-mail: rperkins@pppl.gov; Hosea, J. C.; Jaworski, M. A.; Diallo, A.; Bell, R. E.; Bertelli, N.; Gerhardt, S.; Kramer, G. J.; LeBlanc, B. P.; Phillips, C. K.; Podestà, M.; Roquemore, L.; Taylor, G.; Wilson, J. R. [Princeton Plasma Physics Laboratory, Princeton, New Jersey 08543 (United States); Ahn, J.-W.; Gray, T. K. [Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States); McLean, A. [Lawrence Livermore National Laboratory, Livermore, California 94550 (United States); Sabbagh, S. [Department of Applied Physics and Applied Mathematics, Columbia University, New York, New York 10027 (United States)

    2015-04-15

    The National Spherical Torus eXperiment (NSTX) can exhibit a major loss of high-harmonic fast wave (HHFW) power along scrape-off layer (SOL) field lines passing in front of the antenna, resulting in bright and hot spirals on both the upper and lower divertor regions. One possible mechanism for this loss is RF sheaths forming at the divertors. Here, we demonstrate that swept-voltage Langmuir probe characteristics for probes under the spiral are shifted relative to those not under the spiral in a manner consistent with RF rectification. We estimate both the magnitude of the RF voltage across the sheath and the sheath heat flux transmission coefficient in the presence of the RF field. Although precise comparison between the computed heat flux and infrared (IR) thermography cannot yet be made, the computed heat deposition compares favorably with the projections from IR camera measurements. The RF sheath losses are significant and contribute substantially to the total SOL losses of HHFW power to the divertor for the cases studied. This work will guide future experimentation on NSTX-U, where a wide-angle IR camera and a dedicated set of coaxial Langmuir probes for measuring the RF sheath voltage directly will quantify the contribution of RF sheath rectification to the heat deposition from the SOL to the divertor.

  12. Nonlinear optical rectification and optical absorption in GaAs-Ga1-xAlxAs asymmetric double quantum wells: Combined effects of applied electric and magnetic fields and hydrostatic pressure

    International Nuclear Information System (INIS)

    Karabulut, I.; Mora-Ramos, M.E.; Duque, C.A.

    2011-01-01

    The intersubband electron-related nonlinear optical absorption and nonlinear optical rectification in GaAs-Ga 1-x Al x As asymmetric double quantum wells are studied, under the influence of combined or independent applied electric and magnetic fields as well as hydrostatic pressure. The outcome of the density matrix formalism and the effective mass, and parabolic-band approximations have been considered as main theoretical tools for the description. It is obtained that under particular geometrical conditions, with or without electric and/or magnetic field strength, the optical rectification is null and, simultaneously, in such circumstances the optical absorption has a relative maximum. It is also detected that the influence of the hydrostatic pressure leads to increasing or decreasing behaviors of the nonlinear optical absorption in dependence of the particular regime of pressure values considered, with significant distinction of the cases of opposite electric field orientations. - Highlights: → Maxima of the NOA correspond to zero in the NOR. → Electric fields can couple the double quantum wells. → Hydrostatic pressure can couple the double quantum wells. → NOA can increase/decrease with hydrostatic pressure. → Overlap between wave functions depends on the magnetic field.

  13. Dating ancient monuments by nuclear radiation

    International Nuclear Information System (INIS)

    Goedicke, C.

    2000-01-01

    In the fifties and sixties several disciplines dealing with chronologies but lacking precise methods of measurements (geology, biology, archaeology and art history) became aware of the radioactive decay as a tool of measuring elapsed time. Among the disciplines that benefit most from physical methods archaeology has to be named first. So was archaeological work revolutionised by the introduction of the C-14 dating method. A wider selection of material became datable after the introduction of luminescence techniques using the effect of nuclear radiation on semiconductors. These minerals are widespread among archaeological materials. In ancient monuments, the objective of this paper, semiconductors almost exclusively form the material basis. Over the last four millennia wood, stone, mortar and fired bricks have been used for the construction of buildings. After discussing methods taking wood as a dating material, a broader view will be given on the results achieved by luminescence dating of fired bricks, mortar and stone. For many years brick dating was performed by thermoluminescence, the recipes followed those of ceramic dating. Preferably multiple aliquot additive dose protocols were used on polymineral fine grain fractions (1-10 μm). It was expected that the error in dating monuments would be smaller compared to ceramic dating, because of the constancy of the environmental conditions which a brick experiences during its lifetime. However, the variability of firing temperatures in brick kilns overthrows this advantage. Therefore, the demands of art historians to fall short of an error margin of 5% could generally not be fulfilled. Especially in medieval or renaissance times the temporal resolution of thermoluminescence is inferior to traditional stylistic dating as long as specific stylistic forms are present. New optical luminescence techniques and a new philosophy of dose evaluation, based on single aliquot regeneration protocols, produce less scatter, and in

  14. Development of BASIC program for radiocarbon dating

    International Nuclear Information System (INIS)

    Omoto, Kunio

    1982-01-01

    The continuous improvement of the system and the needs have produced the successful radiocarbon dating system of today to detect very low energy β-radioactivity. However, it still takes longer than 1,000 minutes for a sample counting. In a gas counting system, it is very difficult to keep the drift of impressed high voltage for a proportional counter less than 5 volts throughout the counting time. The temperature and the characteristics of gas itself also change during experiment. The accumulation of the above drift and errors are closely concerned with the accuracy and reliability of the radiocarbon date. The detection and reduction of the errors are only possible by using a ''fully automatic radiocarbon dating system'' linked to a personal computer system. In this paper, the author presents the BASIC (Beginners All-purpose Symbolic Instruction Code) program for a fully automatic radiocarbon dating system. In this paper, the outline of the system and software development are described. The details of the program include the description for gas-collection, gas-enclosing, plateau counting, β-ray counting, age calculation and data file maintenance. The author wrote numerous remark statements into the program so that it can be understood by users without detailed knowledge of the operation of a personal computer system or of the radiocarbon dating. Using this system, the author found that the radiocarbon dating has greatly progressed in speed and labour-saving, and that the accuracy and reliability of the date itself has also improved much than former manual systems. (Wakatsuki, Y.)

  15. Bullying Predicts Reported Dating Violence and Observed Qualities in Adolescent Dating Relationships.

    Science.gov (United States)

    Ellis, Wendy E; Wolfe, David A

    2015-10-01

    The relationship between reported bullying, reported dating violence, and dating relationship quality measured through couple observations was examined. Given past research demonstrating similarity between peer and dating contexts, we expected that bullying would predict negative dating experiences. Participants with dating experience (n = 585; 238 males, M(age) = 15.06) completed self-report assessments of bullying and dating violence perpetration and victimization. One month later, 44 opposite-sex dyads (M(age) = 15.19) participated in behavioral observations. In 10-min sessions, couples were asked to rank and discuss areas of relationship conflict while being video-recorded. Qualities of the relationship were later coded by trained observers. Regression analysis revealed that bullying positively predicted dating violence perpetration and victimization. Self-reported bullying also predicted observations of lower relationship support and higher withdrawal. Age and gender interactions further qualified these findings. The bullying of boys, but not girls, was significantly related to dating violence perpetration. Age interactions showed that bullying was positively predictive of dating violence perpetration and victimization for older, but not younger adolescents. Positive affect was also negatively predicted by bullying, but only for girls. These findings add to the growing body of evidence that adolescents carry forward strategies learned in the peer context to their dating relationships. © The Author(s) 2014.

  16. Radiocarbon dating of ancient Japanese documents

    International Nuclear Information System (INIS)

    Oda, H.

    2001-01-01

    History is a reconstruction of past human activity, evidence of which is remained in the form of documents or relics. For the reconstruction of historic period, the radiocarbon dating of ancient documents provides important information. Although radiocarbon age is converted into calendar age with the calibration curve, the calibrated radiocarbon age is still different from the historical age when the document was written. The difference is known as 'old wood effect' for wooden cultural property. The discrepancy becomes more serious problem for recent sample which requires more accurate age determination. Using Tandetron accelerator mass spectrometer at Nagoya University, we have measured radiocarbon ages of Japanese ancient documents, sutras and printed books written dates of which are clarified from the paleographic standpoint. The purpose is to clarify the relation between calibrated radiocarbon age and historical age of ancient Japanese document by AMS radiocarbon dating. This paper reports 23 radiocarbon ages of ancient Japanese documents, sutras and printed books. The calibrated radiocarbon ages are in good agreement with the corresponding historical ages. It was shown by radiocarbon dating of the ancient documents that Japanese paper has little gap by 'old wood effect'; accordingly, ancient Japanese paper is a suitable sample for radiocarbon dating of recent historic period. (author)

  17. Date Attachable Offline Electronic Cash Scheme

    Directory of Open Access Journals (Sweden)

    Chun-I Fan

    2014-01-01

    Full Text Available Electronic cash (e-cash is definitely one of the most popular research topics in the e-commerce field. It is very important that e-cash be able to hold the anonymity and accuracy in order to preserve the privacy and rights of customers. There are two types of e-cash in general, which are online e-cash and offline e-cash. Both systems have their own pros and cons and they can be used to construct various applications. In this paper, we pioneer to propose a provably secure and efficient offline e-cash scheme with date attachability based on the blind signature technique, where expiration date and deposit date can be embedded in an e-cash simultaneously. With the help of expiration date, the bank can manage the huge database much more easily against unlimited growth, and the deposit date cannot be forged so that users are able to calculate the amount of interests they can receive in the future correctly. Furthermore, we offer security analysis and formal proofs for all essential properties of offline e-cash, which are anonymity control, unforgeability, conditional-traceability, and no-swindling.

  18. Auspicious birth dates among Chinese in California.

    Science.gov (United States)

    Almond, Douglas; Chee, Christine Pal; Sviatschi, Maria Micaela; Zhong, Nan

    2015-07-01

    The number eight is considered lucky in Chinese culture, e.g. the Beijing Olympics began at 8:08 pm on 8/8/2008. Given the potential for discretion in selecting particular dates of labor induction or scheduled Cesarean section (C-section), we consider whether Chinese-American births in California occur disproportionately on the 8th, 18th, or 28th day of the month. We find 2.3% "too many" Chinese births on these auspicious birth dates, whereas Whites show no corresponding increase. The increase in Chinese births is driven by higher parity C-sections: the number of repeat C-sections is 6% "too high" on auspicious birth dates. Sons born to Chinese parents account for the entire increase; daughter deliveries do not seem to be timed to achieve "lucky" birth dates. We also find avoidance of repeat C-section deliveries on the 4th, 14th, and 24th of the month, considered unlucky in Chinese culture. Finally, we replicate earlier work finding that Friday the 13th delivery dates are avoided and document a particularly large decrease among Chinese. For Whites and Chinese in California, mothers with higher levels of education are particularly likely to avoid delivering on the 13th. Copyright © 2015 Elsevier B.V. All rights reserved.

  19. Date attachable offline electronic cash scheme.

    Science.gov (United States)

    Fan, Chun-I; Sun, Wei-Zhe; Hau, Hoi-Tung

    2014-01-01

    Electronic cash (e-cash) is definitely one of the most popular research topics in the e-commerce field. It is very important that e-cash be able to hold the anonymity and accuracy in order to preserve the privacy and rights of customers. There are two types of e-cash in general, which are online e-cash and offline e-cash. Both systems have their own pros and cons and they can be used to construct various applications. In this paper, we pioneer to propose a provably secure and efficient offline e-cash scheme with date attachability based on the blind signature technique, where expiration date and deposit date can be embedded in an e-cash simultaneously. With the help of expiration date, the bank can manage the huge database much more easily against unlimited growth, and the deposit date cannot be forged so that users are able to calculate the amount of interests they can receive in the future correctly. Furthermore, we offer security analysis and formal proofs for all essential properties of offline e-cash, which are anonymity control, unforgeability, conditional-traceability, and no-swindling.

  20. ESR dating of the fault rocks

    International Nuclear Information System (INIS)

    Lee, Hee Kwon

    2005-01-01

    We carried out ESR dating of fault rocks collected near the nuclear reactor. The Upcheon fault zone is exposed close to the Ulzin nuclear reactor. The space-time pattern of fault activity on the Upcheon fault deduced from ESR dating of fault gouge can be summarised as follows : this fault zone was reactivated between fault breccia derived from Cretaceous sandstone and tertiary volcanic sedimentary rocks about 2 Ma, 1.5 Ma and 1 Ma ago. After those movements, the Upcheon fault was reactivated between Cretaceous sandstone and fault breccia zone about 800 ka ago. This fault zone was reactivated again between fault breccia derived form Cretaceous sandstone and Tertiary volcanic sedimentary rocks about 650 ka and after 125 ka ago. These data suggest that the long-term(200-500 k.y.) cyclic fault activity of the Upcheon fault zone continued into the Pleistocene. In the Ulzin area, ESR dates from the NW and EW trend faults range from 800 ka to 600 ka NE and EW trend faults were reactivated about between 200 ka and 300 ka ago. On the other hand, ESR date of the NS trend fault is about 400 ka and 50 ka. Results of this research suggest the fault activity near the Ulzin nuclear reactor fault activity continued into the Pleistocene. One ESR date near the Youngkwang nuclear reactor is 200 ka

  1. Date Attachable Offline Electronic Cash Scheme

    Science.gov (United States)

    Sun, Wei-Zhe; Hau, Hoi-Tung

    2014-01-01

    Electronic cash (e-cash) is definitely one of the most popular research topics in the e-commerce field. It is very important that e-cash be able to hold the anonymity and accuracy in order to preserve the privacy and rights of customers. There are two types of e-cash in general, which are online e-cash and offline e-cash. Both systems have their own pros and cons and they can be used to construct various applications. In this paper, we pioneer to propose a provably secure and efficient offline e-cash scheme with date attachability based on the blind signature technique, where expiration date and deposit date can be embedded in an e-cash simultaneously. With the help of expiration date, the bank can manage the huge database much more easily against unlimited growth, and the deposit date cannot be forged so that users are able to calculate the amount of interests they can receive in the future correctly. Furthermore, we offer security analysis and formal proofs for all essential properties of offline e-cash, which are anonymity control, unforgeability, conditional-traceability, and no-swindling. PMID:24982931

  2. OU3 sediment dating and sedimentation rates

    International Nuclear Information System (INIS)

    Blair, R.B.; Wolaver, H.A.; Burger, V.M.

    1994-01-01

    Environmental Technologies at Rocky Flats Environmental Technology Site (RFS) investigated the sediment history of Standley Lake, Great Western Reservoir, and Mower Reservoir using 137 Cs and 239,240 Pu global fall-out as dating indicators. These Colorado Front Range reservoirs have been the subject of study by various city, state and national agencies due to suspected Department of Energy Rocky Flats Plant impacts. We performed sediment dating as part of the RCRA Facility Investigation/Remedial Investigation Report for Operable Unit 3. A sediment chronology profile assists scientist in determining the year of sedimentation for a particular peak concentration of contaminants. Radioisotope sediment dating for the three reservoirs indicated sedimentation rates of 0.7 to 0.8 in./yr. for Standley Lake (SL), 0.9 in./yr. for Great Western Reservoir (GWR), and 0.3 in./yr. in Mower Reservoir (MR). RFS sediment dating for Operable Unit 3 compared favorably with the Hardy, Livingston, Burke, and Volchok Standley Lake study. This report describes the cesium/plutonium sediment dating method, estimates sedimentation rates for Operable Unit 3 reservoirs, and compares these results to previous investigations

  3. A Proof of Concept for In-Situ Lunar Dating

    Science.gov (United States)

    Anderson, F. S.; Whitaker, T.; Levine, J.; Draper, D. S.; Harris, W.; Olansen, J.; Devolites, J.

    2015-12-01

    We have obtained improved 87Rb-87Sr isochrons for the Duluth Gabbro, an analog for lunar KREEP rocks, using a prototype spaceflight laser ablation resonance ionization mass spectrometer (LARIMS). The near-side of the Moon comprises previously un-sampled, KREEP rich, young-lunar basalts critical for calibrating the dating to constrain lunar history. Using a novel normalization approach, and by correcting for matrix-dependent isotope effects, we have been able to obtain a date of 1100 ± 200 Ma (Figure 1), compared to the previously established thermal ionization mass spectrometry measurement of 1096 ± 14 Ma. The precision of LARIMS is sufficient to constrain the current 1 Ga uncertainty of the lunar flux curve, allowing us to reassess the timing of peak lunar volcanism, and constrain lunar thermal evolution. Furthermore, an updated lunar flux curve has implications throughout the solar system. For example, Mars could have undergone a longer epoch of voluminous, shield-forming volcanism and associated mantle evolution, as well as a longer era of abundant volatiles and hence potential habitability. These alternative chronologies could even affect our understanding of the evolution of life on Earth: under the classic chronology, life is thought to have originated after the dwindling of bombardment, but under the alternative chronology, it might have appeared during heavy bombardment. In order to resolve the science questions regarding the history of the Moon, and in light of the Duluth Gabbro results, we recently proposed a Discovery mission called MARE: The Moon Age and Regolith Explorer. MARE would accomplish these goals by landing on a young, nearside lunar basalt flow southwest of Aristarchus that has a crater density corresponding to a highly uncertain absolute age, collecting >10 rock samples, and assessing their radioisotopic age, geochemistry, and mineralogy.

  4. Thermal insulation

    International Nuclear Information System (INIS)

    Durston, J.G.; Birch, W.; Facer, R.I.; Stuart, R.A.

    1977-01-01

    Reference is made to liquid metal cooled nuclear reactors. In the arrangement described the reactor vessel is clad with thermal insulation comprising a layer of insulating blocks spaced from the wall and from each other; each block is rigidly secured to the wall, and the interspaces are substantially closed against convectional flow of liquid by resilient closure members. A membrane covering is provided for the layer of blocks, with venting means to allow liquid from the reactor vessel to penetrate between the covering and the layer of blocks. The membrane covering may comprise a stainless steel sheet ribbed in orthogonal pattern to give flexibility for the accommodation of thermal strain. The insulating blocks may be comprised of stainless steel or cellular or porous material and may be hollow shells containing ceramic material or gas fillings. (U.K.)

  5. Thermoluminescence of laterites: applicability in dating

    International Nuclear Information System (INIS)

    Sankaran, A.V.; Nambi, K.S.V.; Sunta, C.M.

    1985-01-01

    The northward drift of the Indian subcontinent during the past geological periods brought it under the spell of humid tropical climate in post-mesozoic times which initiated chemical weathering processes (lateritization) of the ancient crustal rocks leading to neomineralization. In the present study, thermoluminescence (TL) of these 'later-formed minerals' has been used to date laterites from a number of localities in India. While the TL emission of most of the laterite samples was poor, three from Kerala, Tamil Nadu and Karnataka states, each derived from mineralogically dissimilar parent rock, yielded measurable TL and provided dates in the range of 2 to 3.6 x 10 5 yr. It is suggested that TL dating can be a promising tool for such samples, and especially those with low alpha activity (U, Th at sub-ppm levels). (author)

  6. Thermoluminescence of laterites: applicability in dating

    Energy Technology Data Exchange (ETDEWEB)

    Sankaran, A V; Nambi, K S.V.; Sunta, C M

    1985-01-01

    The northward drift of the Indian subcontinent during the past geological periods brought it under the spell of humid tropical climate in post-mesozoic times which initiated chemical weathering processes (lateritization) of the ancient crustal rocks leading to neomineralization. In the present study, thermoluminescence (TL) of these 'later-formed minerals' has been used to date laterites from a number of localities in India. While the TL emission of most of the laterite samples was poor, three from Kerala, Tamil Nadu and Karnataka states, each derived from mineralogically dissimilar parent rock, yielded measurable TL and provided dates in the range of 2 to 3.6 x 10/sup 5/ yr. It is suggested that TL dating can be a promising tool for such samples, and especially those with low alpha activity (U, Th at sub-ppm levels).

  7. Geological Survey of Canada radiocarbon dates XXIX

    International Nuclear Information System (INIS)

    McNeely, R.; McCuaig, S.

    1991-01-01

    This list presents 622 radiocarbon age determinations made by the Radiocarbon Dating Laboratory. All samples dated more than two years ago have now been reported in date lists. The total number (609) of samples from various areas are as follows: Offshore (43); Newfoundland (42); Labrador (11); Nova Scotia (39); New Brunswick (7); Champlain Sea (38); Quebec (54); Ontario (23); Manitoba (3); Saskatchewan (9); Alberta (6); British Columbia (92); Yukon Territory (71); Northwest Territories, mainland (33); Northwest Territories, Arctic Archipelago (126); U.S.A. - New York (6); Washington (1); Denmark Greenland (3). Tables 1 and 2 summarize the details of background and standard counts for the 2 L and 5 L counters during the period from December 6, 1988 to January 9, 1990. (author). Refs

  8. Geological Survey of Canada radiocarbon dates XXIX

    Energy Technology Data Exchange (ETDEWEB)

    McNeely, R; McCuaig, S

    1992-12-31

    This list presents 622 radiocarbon age determinations made by the Radiocarbon Dating Laboratory. All samples dated more than two years ago have now been reported in date lists. The total number (609) of samples from various areas are as follows: Offshore (43); Newfoundland (42); Labrador (11); Nova Scotia (39); New Brunswick (7); Champlain Sea (38); Quebec (54); Ontario (23); Manitoba (3); Saskatchewan (9); Alberta (6); British Columbia (92); Yukon Territory (71); Northwest Territories, mainland (33); Northwest Territories, Arctic Archipelago (126); U.S.A. - New York (6); Washington (1); Denmark Greenland (3). Tables 1 and 2 summarize the details of background and standard counts for the 2 L and 5 L counters during the period from December 6, 1988 to January 9, 1990. (author). Refs.

  9. Radiocarbon dating with accelerator mass spectrometry

    International Nuclear Information System (INIS)

    Blake, W. Jr.

    1985-01-01

    Radiocarbon dating by means of accelerator mass spectrometry (AMS) has two great advantages over conventional dating: 1) much smaller samples can be handled and 2) counting time is significantly shorter. Three examples are given for Holocene-age material from east-central Ellesmere Island. The results demonstrate the potential use of this technique as a powerful research tool in studies of Quaternary chronology. Individual fragments of marine shells as small as 0.1 g have been dated successfully at the IsoTrace Laboratory, University of Toronto. In the case of an aquatic moss from a lake sediment core, an increment 0.5 cm thick could be used instead of a 5 cm-thick slice, thus allowing a much more precise estimate of the onset of organic sedimentation

  10. Solar thermal

    International Nuclear Information System (INIS)

    Jones, J.

    2006-01-01

    While wind power is widely acknowledged as the most developed of the 'new' renewables, the number two technology, in terms of installed capacity functioning worldwide, is solar heating, or solar thermal. The author has investigated recent industry reports on how these markets are developing. The authors of an International Energy Agency (IEA) survey studied 41 countries in depth at the end of 2004, revealing that 141 million m 3 - corresponding to an installed capacity of 98.4 GWth - were installed in the sample countries (these nations represent 3.74 billion people, about 57% of the world's population). The installed capacity within the areas studied represents approximately 85%-90% of the solar thermal market worldwide. The use of solar heating varies greatly between countries - even close neighbours - and between economic regions. Its uptake often has more to do with policy than solar resource. There is also different uptake of technology. In China, Europe and Japan, plants with flat-plate and evacuated tube collectors are used, mainly to heat water and for space heating. Unglazed plastic collectors, used mainly for swimming pool heating, meanwhile, dominate the North American markets. Though the majority of solar heating installations today are installed on domestic rooftops, the larger-scale installations should not be overlooked. One important part of the market is the hotel sector - in particular hotels in locations that serve the seasonal summer holiday market, where solar is extremely effective. Likewise hospitals and residential homes, multi-family apartment blocks and sports centres are all good examples of places where solar thermal can deliver results. There are also a growing number of industrial applications, where solar thermal can meet the hot water needs (and possibly more) of a range of industries, such as food processing and agriculture. The ability of solar to provide a heat source for cooling is expected to become increasingly important as

  11. Solar thermal

    Energy Technology Data Exchange (ETDEWEB)

    Jones, J.

    2006-07-15

    While wind power is widely acknowledged as the most developed of the 'new' renewables, the number two technology, in terms of installed capacity functioning worldwide, is solar heating, or solar thermal. The author has investigated recent industry reports on how these markets are developing. The authors of an International Energy Agency (IEA) survey studied 41 countries in depth at the end of 2004, revealing that 141 million m{sup 3} - corresponding to an installed capacity of 98.4 GWth - were installed in the sample countries (these nations represent 3.74 billion people, about 57% of the world's population). The installed capacity within the areas studied represents approximately 85%-90% of the solar thermal market worldwide. The use of solar heating varies greatly between countries - even close neighbours - and between economic regions. Its uptake often has more to do with policy than solar resource. There is also different uptake of technology. In China, Europe and Japan, plants with flat-plate and evacuated tube collectors are used, mainly to heat water and for space heating. Unglazed plastic collectors, used mainly for swimming pool heating, meanwhile, dominate the North American markets. Though the majority of solar heating installations today are installed on domestic rooftops, the larger-scale installations should not be overlooked. One important part of the market is the hotel sector - in particular hotels in locations that serve the seasonal summer holiday market, where solar is extremely effective. Likewise hospitals and residential homes, multi-family apartment blocks and sports centres are all good examples of places where solar thermal can deliver results. There are also a growing number of industrial applications, where solar thermal can meet the hot water needs (and possibly more) of a range of industries, such as food processing and agriculture. The ability of solar to provide a heat source for cooling is expected to become

  12. Disinfestation of Date Fruits by Gamma Radiation and Its Effect on the Nutritional Contents of Dates

    International Nuclear Information System (INIS)

    Ahmed, Z.A.; Boshra, S.A.; Mikhaiel, A.A.; Hassan, N.M.

    2008-01-01

    Irradiation dis infestations of Siwa date fruits seems to be a very promising method. Considerations of the health safety of irradiated date fruits involve nutritional contents has been investigated by chemical analysis. The dose of 400 and 1000 Gy were lethal for the different stages of oases date moth, Ephestia calidella. Dates are a good source of iron and potassium, they also contain calcium, magnesium, copper and other minerals. The radiation dose 1000 Gy had mostly affected the carbohydrates content, some minerals as Fe, Ca and Na partially changed by the treatment. Protein and vitamin contents were slightly affected

  13. An assessment of variability in radiocarbon dating

    International Nuclear Information System (INIS)

    Scott, E.M.; Baxter, M.S.; Aitchison, T.C.

    1981-01-01

    A series of replicate experiments, involving analysis of homogenized wood and identical tree-ring sections, suggests that the 14 C counting error in radiocarbon dating quantifies only part of the total variability of measurement. Statistical modelling implies that a more realistic assessment of error is provided by a value approximately three times the counting error. The incorporation of this more realistic measure of variability into an appropriate procedure for calibrating a single date and for matching a floating chronology to a master chronology is described. (author)

  14. Dating Petroglyphs from Fugoppe Cave, Japan

    Directory of Open Access Journals (Sweden)

    Masaru Ogawa

    2014-01-01

    Full Text Available For over 20 years, I have tried to establish a relative date for petroglyphs in Fugoppe Cave, Japan. Unsuspected amidst debris accumulating from about 1300 years ago, the petroglyphs were rediscovered accidentally in 1950. From an analysis of petroglyphs on fallen rocks scattered randomly on the site floor, I argue that the artworks date from ca.1900 years ago. The cave itself, formed by wave action, saw its main occupation by pottery-making people from 1700–1500 years ago; although the petroglyphs on the rock walls predated their occupation, it seems unlikely that the occupants attached any meaning to them.

  15. Characterization of untreated and treated male and female date palm leaves

    International Nuclear Information System (INIS)

    AlMaadeed, M.A.; Kahraman, Ramazan; Noorunnisa Khanam, P.; Al-Maadeed, Somaya

    2013-01-01

    Highlights: ► Sheshi female and male date palm leaves were treated with NaOH concentrations. ► Male leaves have lower mechanical properties and improved when treated by NaOH 2%. ► Female leaves have higher thermal stability. ► There are different properties for different types of date leaves. ► Leaves can be used as reinforcements for thermoplastic materials. -- Abstract: This paper describes the characterization of male and female date palm leaves from two different cultivars, Sheshi female and unknown male leaves. Characterization was done for both untreated and NaOH treated date palm leaves by infrared spectroscopy, thermogravimetric analysis and scanning electron microscopic techniques. To our knowledge, the difference in specious reaction to the treatment type of date palm fiber has not been investigated earlier. These leaves were treated with different concentrations of NaOH, 0.5%, 1%, 2% and 5% (w/w). The results from this investigation indicate that female leaves have better tensile properties which deteriorate with the increase of the alkali. The male leaves have lower tensile properties than female leaves and their mechanical properties are improved slightly by NaOH treatment. Female leaves have more pores than male leaves, this was proved and calculated by image analysis. Untreated female leaves have higher thermal stability (353 °C) than male leaves (343 °C). Both can be used as reinforcements in thermoplastic matrix materials whose processing temperatures are below 300 °C.

  16. Obsidian Hydration Dating in the Undergraduate Curriculum.

    Science.gov (United States)

    Manche, Emanuel P.; Lakatos, Stephen

    1986-01-01

    Provides an overview of obsidian hydration dating for the instructor by presenting: (1) principles of the method; (2) procedures; (3) applications; and (4) limitations. The theory of the method and one or more laboratory exercises can be easily introduced into the undergraduate geology curriculum. (JN)

  17. 29 CFR 1910.98 - Effective dates.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 5 2010-07-01 2010-07-01 false Effective dates. 1910.98 Section 1910.98 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... section, if any standard in 41 CFR part 50-204, other than a national consensus standard incorporated by...

  18. Use of radiocarbon technique for archaelogic dating

    International Nuclear Information System (INIS)

    Chausson, Y.

    1986-01-01

    The nuclear technique based on the beta radiation measurements emitted by the radiocarbon is applied an the geochronologycal dating of organic samples of prehistoric fires and sambaqui shells. This paper describes the origin of the method, the technique used and its applications, the analysis method, the equipments and the experiences performed. (Author) [pt

  19. 77 FR 30928 - Target Date Disclosure

    Science.gov (United States)

    2012-05-24

    ... DEPARTMENT OF LABOR Employee Benefits Security Administration 29 CFR Part 2550 RIN 1210-AB38 Target Date Disclosure AGENCY: Employee Benefits Security Administration, Labor. ACTION: Proposed rule; reopening of comment period. SUMMARY: The Department of Labor's Employee Benefits Security Administration is...

  20. When Pregnancy Goes Past Your Due Date

    Science.gov (United States)

    ... due date determined? • What is postterm pregnancy? • What causes a postterm pregnancy? • What are the risks associated with postterm pregnancy? • ... longer than 42 weeks is called “postterm.” What causes a postterm pregnancy? The causes of postterm pregnancy are unknown, but ...

  1. Radiocarbon dating of interlaboratory check samples

    International Nuclear Information System (INIS)

    Blake, W.

    1983-01-01

    This note presents the results of a series of interlaboratory age determinations in which the Geological Survey of Canada's Radiocarbon Dating Laboratory has been involved. There is good agreement between laboratories, although there may be other problems related to the interpretation of individual samples

  2. Physical Dating Aggression Growth during Adolescence

    Science.gov (United States)

    Nocentini, Annalaura; Menesini, Ersilia; Pastorelli, Concetta

    2010-01-01

    The development of Physical Dating Aggression from the age of 16 to 18 years was investigated in relation to time-invariant predictors (gender, parental education, family composition, number of partners) and to time-varying effects of delinquent behavior and perception of victimization by the partner. The sample consisted of 181 adolescents with a…

  3. 31 CFR 595.302 - Effective date.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Effective date. 595.302 Section 595.302 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE OF FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY TERRORISM SANCTIONS REGULATIONS General Definitions...

  4. 50 CFR 216.212 - Effective dates.

    Science.gov (United States)

    2010-10-01

    ..., DEPARTMENT OF COMMERCE MARINE MAMMALS REGULATIONS GOVERNING THE TAKING AND IMPORTING OF MARINE MAMMALS Taking of Marine Mammals Incidental to Explosive Severance Activities Conducted During Offshore Structure Removal Operations on the Outer Continental Shelf in the U.S. Gulf of Mexico § 216.212 Effective dates...

  5. Date change and safeguards at Dounreay

    International Nuclear Information System (INIS)

    Anderson, A.; Gregory, C.V.

    1999-01-01

    The paper briefly describes the arrangements in Dounreay for tackling the Millennium problem and for managing the accountancy of fissile material. The impact of the date change upon safeguards at Dounreauy has been assessed and the paper shows the problems which have been identified and are being tackled with

  6. Historical Analysis of College Campus Interracial Dating

    Science.gov (United States)

    Firmin, Michael W.; Firebaugh, Stephanie

    2008-01-01

    Interracial dating on American campuses has had a relatively stormy past. Until the past three decades or so, it was outlawed in some states. Southern institutions, in particular, such as the infamous Bob Jones University have made this issue divisive even among their own constituencies. Age and generation seem to be cogent factors with younger…

  7. ESR dating of the fault rocks

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Hee Kwon [Kangwon National Univ., Chuncheon (Korea, Republic of)

    2004-01-15

    Past movement on faults can be dated by measurement of the intensity of ESR signals in quartz. These signals are reset by local lattice deformation and local frictional heating on grain contacts at the time of fault movement. The ESR signals then grow back as a result of bombardment by ionizing radiation from surrounding rocks. The age is obtained from the ratio of the equivalent dose, needed to produce the observed signal, to the dose rate. Fine grains are more completely reset during faulting, and a plot of age vs, grain size shows a plateau for grains below critical size : these grains are presumed to have been completely zeroed by the last fault activity. We carried out ESR dating of fault rocks collected near the Ulzin nuclear reactor. ESR signals of quartz grains separated from fault rocks collected from the E-W trend fault are saturated. This indicates that the last movement of these faults had occurred before the quaternary period. ESR dates from the NW trend faults range from 300ka to 700ka. On the other hand, ESR date of the NS trend fault is about 50ka. Results of this research suggest that long-term cyclic fault activity near the Ulzin nuclear reactor continued into the pleistocene.

  8. Radiocarbon dating of ancient rock paintings

    Energy Technology Data Exchange (ETDEWEB)

    Ilger, W.A.; Hyman, M.; Rowe, M.W. [Texas A and M Univ., College Station, TX (United States). Dept. of Chemistry; Southon, J. [Lawrence Livermore National Lab., CA (United States)

    1995-06-20

    This report presents progress made on a technique for {sup 14}C dating pictographs. A low-temperature oxygen plasma is used coupled with high-vacuum technologies to selectively remove C-containing material in the paints without contamination from inorganic carbon from rock substrates or accretions.

  9. 38 CFR 21.7135 - Discontinuance dates.

    Science.gov (United States)

    2010-07-01

    ...; Pub. L. 98-525) (c) Divorce. If the veteran becomes divorced, the effective date of reduction of his or her educational assistance is the last day of the month in which the divorce occurs. (Authority...) If the veteran or servicemember, for reasons other than being called or ordered to active duty...

  10. Radiocarbon dating of ancient rock paintings

    International Nuclear Information System (INIS)

    Ilger, W.A.; Hyman, M.; Rowe, M.W.

    1995-01-01

    This report presents progress made on a technique for 14 C dating pictographs. A low-temperature oxygen plasma is used coupled with high-vacuum technologies to selectively remove C-containing material in the paints without contamination from inorganic carbon from rock substrates or accretions

  11. Bournonite PbCuSbS3 : Stereochemically Active Lone-Pair Electrons that Induce Low Thermal Conductivity.

    Science.gov (United States)

    Dong, Yongkwan; Khabibullin, Artem R; Wei, Kaya; Salvador, James R; Nolas, George S; Woods, Lilia M

    2015-10-26

    An understanding of the structural features and bonding of a particular material, and the properties these features impart on its physical characteristics, is essential in the search for new systems that are of technological interest. For several relevant applications, the design or discovery of low thermal conductivity materials is of great importance. We report on the synthesis, crystal structure, thermal conductivity, and electronic-structure calculations of one such material, PbCuSbS3 . Our analysis is presented in terms of a comparative study with Sb2 S3 , from which PbCuSbS3 can be derived through cation substitution. The measured low thermal conductivity of PbCuSbS3 is explained by the distortive environment of the Pb and Sb atoms from the stereochemically active lone-pair s(2) electrons and their pronounced repulsive interaction. Our investigation suggests a general approach for the design of materials for phase-change-memory, thermal-barrier, thermal-rectification and thermoelectric applications, as well as other functions for which low thermal conductivity is purposefully sought. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. The unexpected truth about dates and hypoglycemia

    Directory of Open Access Journals (Sweden)

    Mohammed I Yasawy

    2016-01-01

    Full Text Available Background: Dates are a concentrated source of essential nutrients, vitamins, minerals, and carbohydrates (CHOs, which are necessary for the maintenance of optimum health. Most of the CHOs in dates come from sugars including glucose and fructose. Dates are commonly consumed in Saudi Arabia, particularly at the time of breaking the fast to provide instant energy and maintain blood sugar level. However, dates may cause hypoglycemia in a rare condition named as heredity fructose intolerance (HFI, and a few families have been to see us with a history of that nature. This is to report the preliminary results of an on-going study of a group of patients who get symptoms of hypoglycemia following the ingestion of dates and have suffered for years without an accurate diagnosis. Methodology: This report is based on three patients, from the same family, living in a date growing region of the Kingdom of Saudi Arabia (KSA. The patients had been to several medical centers without getting any definite answers or diagnosis until they were referred to the Gastroenterology Clinic of King Fahd Hospital of the University, Al-Khobar, KSA. The data were obtained by careful history and laboratory investigations, and a final diagnosis of HFI made on fructose intolerance test (FIT. Results: The patients reported that they had avoided eating dates because of various symptoms, such as bloating, nausea, and even hypoglycemia when larger amounts were consumed. Their other symptoms included sleepiness, sweating, and shivering. After full examinations and necessary laboratory tests based on the above symptoms, FIT was performed and the patients were diagnosed with HFI. They were referred to a dietitian who advised a fructose-free diet. They felt well and were free of symptoms. Conclusion: HFI may remain undiagnosed until adulthood and may lead to disastrous complications and even death. The diagnosis can only be suspected after a careful dietary history is taken supported by

  13. Single-machine scheduling with release dates, due dates and family setup times

    NARCIS (Netherlands)

    Schutten, Johannes M.J.; van de Velde, S.L.; van de Velde, S.L.; Zijm, Willem H.M.

    1996-01-01

    We address the NP-hard problem of scheduling n independent jobs with release dates, due dates, and family setup times on a single machine to minimize the maximum lateness. This problem arises from the constant tug-of-war going on in manufacturing between efficient production and delivery

  14. Single-machine scheduling with release dates, due dates, and family setup times

    NARCIS (Netherlands)

    J.M.J. Schutten (Marco); S.L. van de Velde (Steef); W.H.M. Zijm

    1996-01-01

    textabstractWe address the NP-hard problem of scheduling n independent jobs with release dates, due dates, and family setup times on a single machine to minimize the maximum lateness. This problem arises from the constant tug-of-war going on in manufacturing between efficient production and delivery

  15. Power Generation from a Radiative Thermal Source Using a Large-Area Infrared Rectenna

    Science.gov (United States)

    Shank, Joshua; Kadlec, Emil A.; Jarecki, Robert L.; Starbuck, Andrew; Howell, Stephen; Peters, David W.; Davids, Paul S.

    2018-05-01

    Electrical power generation from a moderate-temperature thermal source by means of direct conversion of infrared radiation is important and highly desirable for energy harvesting from waste heat and micropower applications. Here, we demonstrate direct rectified power generation from an unbiased large-area nanoantenna-coupled tunnel diode rectifier called a rectenna. Using a vacuum radiometric measurement technique with irradiation from a temperature-stabilized thermal source, a generated power density of 8 nW /cm2 is observed at a source temperature of 450 °C for the unbiased rectenna across an optimized load resistance. The optimized load resistance for the peak power generation for each temperature coincides with the tunnel diode resistance at zero bias and corresponds to the impedance matching condition for a rectifying antenna. Current-voltage measurements of a thermally illuminated large-area rectenna show current zero crossing shifts into the second quadrant indicating rectification. Photon-assisted tunneling in the unbiased rectenna is modeled as the mechanism for the large short-circuit photocurrents observed where the photon energy serves as an effective bias across the tunnel junction. The measured current and voltage across the load resistor as a function of the thermal source temperature represents direct current electrical power generation.

  16. Internet dating as a project: the commodification and rationalisation of online dating

    Directory of Open Access Journals (Sweden)

    Tjaša Žakelj

    2015-04-01

    Full Text Available Based on qualitative empirical data from two studies on Internet dating in Slovenia, this paper discusses the social contexts of the Internet dating of heterosexual men and women and homosexual men. Special attention is given to different aspects of the commodification and rationalisation of dating in the process of forming potential (romantic partnerships. First, we discuss our respondents’ reasons for using the Internet to get in touch with potential (romantic partners. Second, we focus on the demands and strategies of targeted market- ing in personal profile writing and, finally, on the process of selecting potential partners. Our study shows that the primary understanding of Internet dating among people who engage in it is its economic nature. Together with targeted marketing and the predeter- mined criteria for choosing interesting others, Internet dating can thus be understood as a market that encourages rationalisation and commodification in the process of forming intimate relationships.

  17. Witnessing Interparental Violence and Acceptance of Dating Violence as Predictors for Teen Dating Violence Victimization.

    Science.gov (United States)

    Karlsson, Marie E; Temple, Jeff R; Weston, Rebecca; Le, Vi Donna

    2016-04-01

    We examined the association between witnessing interparental violence, attitudes about dating violence, and physical and psychological teen dating violence (TDV) victimization. Participants were 918 teens with dating experience. Witnessing interparental violence and acceptance of dating violence were significant predictors of TDV victimization. Acceptance of dating violence was also a partial mediator between witnessing interparental violence and TDV victimization. Witnessing mother-to-father violence and acceptance of female-perpetrated violence were the most consistent predictors. TDV programs aiming to prevent victimization could benefit from targeting youth exposed to father-to-mother and mother-to-father violence, targeting attitudes about violence, and tailoring interventions to gender-specific risk factors. © The Author(s) 2015.

  18. Up-Dating: Ratings of Perceived Dating Success Are Better Online than Offline.

    Science.gov (United States)

    Fullwood, Chris; Attrill-Smith, Alison

    2018-01-01

    The primary aims of this study were to test whether perceived dating success would differ between offline and online zero-acquaintance dating contexts and to investigate the role that self-esteem might play in these evaluations. Participants were presented with the same photos of targets in either an offline or online dating scenario and rated their chances of dating success along with their perceptions of how attractive they thought the target would consider them. Higher self-esteem individuals believed they would be rated as more attractive. There was an overall perception that, irrespective of self-esteem level, meeting online would lead to better chances of dating success. These findings are considered in relation to an increased ability to more precisely manage impressions and develop an image of the self which would be evaluated more positively online.

  19. Fission track dating method: I. Study of neutron flux uniformity in some irradiation positions of IEA-R1 reactor

    International Nuclear Information System (INIS)

    Osorio, A.M.; Hadler, J.C.; Iunes, P.J.; Paulo, S.R. de

    1993-06-01

    In order to use the fission track dating method the flux gradient was verified within the sample holder, in some irradiation positions of the IEA-R1 reactor at IPEN/CNEN, Sao Paulo. The fission track dating method considers only the thermal neutron fission tracks, to subtract the other contributions sample irradiations with a cadmium cover was performed. The neutron flux cadmium influence was studied. (author)

  20. Determination of g-tensors of low-symmetry Nd{sup 3+} centers in LiNbO{sub 3} by rectification of angular dependence of electron paramagnetic resonance spectra

    Energy Technology Data Exchange (ETDEWEB)

    Grachev, V., E-mail: grachev@physics.montana.edu; Malovichko, G. [Physics Department, Montana State University, Bozeman, Montana 59717 (United States); Munro, M. [Quantel Laser, Bozeman, Montana 59715 (United States); Kokanyan, E. [Institute of Physical Researches, Ashtarak (Armenia)

    2015-07-28

    Two procedures for facilitation of line tracing and deciphering of complicated spectra of electron paramagnetic resonance (EPR) were developed: a correction of microwave frequencies for every orientation of external magnetic field on the base of known values of g-tensor components for a reference paramagnetic center and followed rectification of measured angular dependences using plots of effective deviation of g{sup 2}-factors of observed lines from effective g{sup 2}-factors of the reference center versus angles or squared cosines of angles describing magnetic field orientations. Their application to EPR spectra of nearly stoichiometric lithium niobate crystals doped with neodymium allowed identifying two axial and six different low-symmetry Nd{sup 3+} centers, to determine all components of their g-tensors, and to propose common divacancy models for a whole family of Nd{sup 3+} centers.

  1. Optical rectification in a strained GaAs{sub 0.9}P{sub 0.1}/GaAs{sub 0.6}P{sub 0.4} quantum dot: Simultaneous effects of electric and magnetic fields

    Energy Technology Data Exchange (ETDEWEB)

    Vinolin, Ada [Dept. of Physics, Madurai Kamaraj University College, Alagarkoil Road, Madurai-625002 (India); Peter, A. John, E-mail: a.john.peter@gmail.com [Dept. of Physics, Government Arts College, Melur-625106, Tamilnadu (India)

    2014-04-24

    Simultaneous effects of electric field and magnetic field on exciton binding energy as a function of dot radius in a cylindrical GaAs{sub 0.9}P{sub 0.1}/GaAs{sub 0.6}P{sub 0.4} strained quantum dot are investigated. The strain contribution includes the strong built-in electric field induced by the spontaneous and piezoelectric polarizations. Numerical calculations are performed using variational procedure within the single band effective mass approximation. Optical rectification in the GaAs{sub 0.9}P{sub 0.1}/GaAs{sub 0.6}P{sub 0.4} quantum dot is computed in the presence of electric and magnetic fields.

  2. Mercury in dated Greenland marine sediments

    DEFF Research Database (Denmark)

    Asmund, G.; Nielsen, S.P.

    2000-01-01

    Twenty marine sediment cores from Greenland were analysed for mercury, and dated by the lead-210 method. In general the cores exhibit a mercury profile with higher mercury concentrations in the upper centimetres of the core. The cores were studied by linear regression of In Hg vs, age of the sedi......Twenty marine sediment cores from Greenland were analysed for mercury, and dated by the lead-210 method. In general the cores exhibit a mercury profile with higher mercury concentrations in the upper centimetres of the core. The cores were studied by linear regression of In Hg vs, age...... indicating that the mercury mainly originates from atmospheric washout. But the large variability indicates that other processes also influence the mercury flux to Arctic marine sediments. (C) 2000 Elsevier Science B.V. All rights reserved....

  3. 210Pb dating of Baltic Sea sediments

    International Nuclear Information System (INIS)

    Gellermann, R.

    1990-01-01

    The paper reports on the results of 210 Pb measurement in sediment cores from the Baltic Sea. The models used for the interpretation are derived and discussed. In general, the sedimentation parameters calculated with different models are consistent. However, parameters of cores independently taken on same partly show clearly differing values. The reasons of this observation have to be analysed by further studies. An essential problem considered in this paper is the dating of disturbed sediments. The use of such cores for the reconstruction of the input history of chemical indicators requires a deconvolution of data. The response function necessary for this procedure can be derived from 210 Pb measurements. The results of such a reconstruction considerably differ from those obtained by conventional dating models. The analysis of the measuring uncertainty of the indicator (e.g. lead) in the deconvolution procedure unveals the limits of the method and prevents it from overinterpretation. (orig.) [de

  4. Dating methods and their relevance in physics

    International Nuclear Information System (INIS)

    Schneider, H.

    1981-01-01

    The article describes some of the most important radiometric clocks. It is pointed out how much the chronological interpretation of isotopic ratios depends on preconceived models about origin and history of investigated minerals. A number of physico-chemical effects are discussed, which give rise to fictitious datings. The possibility is considered that all the radiometric ages used for establishing the geologic time scale might be due to such effects. The history and foundations of the latter are reviewed, and the possibility of a wrong decision is mentioned. Several results from fossil objects indicate very young ages. The usual treatment of anomalous results is criticised. Long-time clocks fails to reproduce documented young ages. It is suggested that in the age interpretation of isotopic ratios much younger than conventional ages be also taken into consideration. The importance of directly dating fossils is stressed. (orig./HP) [de

  5. Radiocarbon dating development and practices at MINT

    International Nuclear Information System (INIS)

    Kamisah Alias; Bashillah Baharuddin; Juhari Mohd Yusof; Ahmad Raduan Ujang

    2002-01-01

    The MINT radiocarbon dating technique was introduced and a very well-designed vacuum line was developed to generate benzene from samples containing carbon. A liquid scintillation counter provides a very good prerequisite for precise measurement of the C-14 activity in the benzene. From time to time, assessment on the status of the analytical capabilities of the system and advice on improvement and upgrading required was made. For routine analysis, standard sampling, pretreatment, carbon dioxide conversion and measurement procedures were adopted. Radiocarbon dating is now, one of the most important developments of the twenties century in the comprehension of the history of human development, a quick, easy, reliable and scientifically acceptable method to determine the age of historical artefacts and archaeological samples. (Author)

  6. Perspectives in radiocarbon dating by radiometry

    International Nuclear Information System (INIS)

    Polach, H.A.

    1987-01-01

    Opportunities for individual contributions to the technology of radiocarbon dating over the past 40 years have been large. Meaningful developments are traced in this review of C-14 dating by gas proportional (GP) and liquid scintillation (LS) spectrometry. The performance of characteristic as well as state of the art GP and LS systems is tabulated and their merit for low-level counting of C-14 is evaluated. Future developments in radiometry will lie in the updating of existing systems to incorporate new technologies and the refinement of resolution and identification of extreme low-level signals. Parallel development with AMS, sharing on merit the ever widening applied C-14 research field, and enhanced interdisciplinary collaboration are foreseen as the scenario leading to the year 2000

  7. Perspectives in radiocarbon dating by radiometry

    International Nuclear Information System (INIS)

    Polach, H.A.

    1987-01-01

    Opportunities for individual contributions to the technology of radiocarbon dating over the past 40 years have been large. Meaningful developments are traced in this review of C-14 dating by gas proportional (GP) and liquid scintillation (LS) spectrometry. The performance of characteristic as well as state of the art GP and LS systems is tabulated and their merit for low-level counting of C-14 is evaluated. Future developments in radiometry will lie in the updating of existing systems to incorporate new technologies and the refinement of resolution and identification of extreme low-level signals. Parallel development with AMS, sharing on merit the ever widening applied C-14 research field, and enhanced interdisciplinary collaboration are foreseen as the scenario leading to the year 2000. (orig.)

  8. The freshwater reservoir effect in radiocarbon dating

    DEFF Research Database (Denmark)

    Philippsen, Bente

    case studies will show the degree of variability of the freshwater reservoir effect over short and long timescales. Radiocarbon dating of recent water samples, aquatic plants and animals, shows that age differences of up to 2000 years can occur within one river. In the Limfjord, freshwater influence......The freshwater reservoir effect can result in too high radiocarbon ages of samples from lakes and rivers, including the bones of people whose subsistence was based on freshwater fish, and pottery in which fish was cooked. In my talk, I will explain the causes and consequences of this effect. Two...... caused reservoir ages to vary between 250 and 700 years during the period 5400 BC - AD 700. Finally, I will discuss the implications of the freshwater reservoir effect for radiocarbon dating of Mesolithic pottery from inland sites of the Ertebølle culture in Northern Germany....

  9. Towards Luminescence Dating Of Mosaic Glass

    Science.gov (United States)

    Galli, A.; Martini, M.; Sibila, E.; Villa, I.

    The possibility of dating archaeological glass by means of luminescent techniques has been investigated in recent years, despite the difficulties of this application, mainly linked to the amorphous structure of the material. We focused in particular on mosaic glass, after the encouraging results obtained on byzantine and medieval samples. Further studies were devoted to the comprehension of the luminescent mechanisms in silica glasses, and to the investigation of the relationships between luminescence, colouring or opacifier ions and crystalline phase of the vitreous matrix. The results of a study on the dosimetric characteristics of thermoluminescence (TL) and Optically Stimulated Luminescence (OSL) of a few medieval blue-green mosaic glasses from the San Lorenzo church (Milan) are presented, and the experimental protocols established to identify their suitability for dating are discussed.

  10. AGAR PENULISAN RESEP TETAP UP TO DATE

    Directory of Open Access Journals (Sweden)

    Rahmatini Rahmatini

    2009-09-01

    Full Text Available AbstrakResep adalah suatu permintaan tertulis dari dokter, dokter gigi atau dokter hewan kepada apoteker untuk membuatkan obat dalam bentuk sediaan tertentu dan menyerahkannya kepada pasien. Resep merupakan perwujudan akhir dari kompetensi, pengetahuan dan keahlian dokter dalam menerapkan pengetahuannya dalam bidang farmakologi dan terapi.Penulisan resep harus ditulis dengan jelas sehingga dapat dibaca oleh petugas di apotek. Resep yang ditulis dengan tidak jelas akan menimbulkan terjadinya kesalahan saat peracikan / penyiapan obat dan penggunaan obat yang diresepkan.Ilmu pengetahuan tentang obat selalu berubah, obat – obat baru selalu muncul di pasaran.Secara umum, seorang dokter harus mengikuti perkembangan dalam terapi obat. Bila muncul efek samping akibat obat yang seharusnya diketahui dan dapat dicegah oleh dokter, maka dokter akan berhadapan dengan hukum.Agar penulisan resep tetap up to date, seorang dokter harus mengumpulkan berbagai informasi yang tersedia. Sumber informasi yang dapat digunakan adalah : Buku acuan, Kompendium obat, Daftar Obat Esensial Nasional (DOEN dan Pedoman terapi, Buletin obat, Jurnal Kedokteran, Pusat informasi obat,Informasi melalui komputer, Sumber informasi dari industri farmasi, dan informasi lisan.Bandingkan kelebihan dan kekurangan berbagai sumber informasi. Tugas seorang dokter adalah melakukan cara terbaik untuk tetap up to date dengan mendaftar sumber informasi yang dapat dimanfaatkan. Carilah sedikitnya satu dari yang berikut ini : (1 jurnal kedokteran: (2 buletin obat; (3 buku acuan farmakologi atau acuan klinis; (4 komisi terapi maupun konsultan, atau lulusan pasca sarjana farmakologi. Dengan bekal pengetahuan dan kemampuan untuk melakukan penilaian secara kritis setiap bentuk informasi, diharapkan dokter tetap up to date dalam menulis resepKata kunci : Resep – up to- date.Abstract Prescription is a written request from a doctor, dentist or veterinarian to the pharmacist to make a particular drug

  11. Radiocarbon dating methods using benzene liquid scintillation

    International Nuclear Information System (INIS)

    Togashi, Shigeko; Matsumoto, Eiji

    1983-01-01

    The radiocarbon dating method using benzene liquid scintillation is reported in detail. The results of measurement of NBS oxalic acid agree with the recommended value, indicating that isotopic fractionation during benzene synthesis can be negligible. Ten samples which have been already measured by gas counter are dated by benzene liquid scintillation. There is no significant difference in age for the same sample between benzene liquid scintillation and gas counters. It is shown that quenching has to be corrected for the young sample. Memory effect in stainless steel reaction vessel can be removed by using an exchangeable inner vessel and by baking it in the air. Using this method, the oldest age that can be measured with 2.3 g carbon is 40,000 years B.P. (author)

  12. William Crabtree and the date of Easter

    Science.gov (United States)

    Sellers, D.

    2014-04-01

    A previously unknown treatise by William Crabtree (c.1603-c.1644) has recently been unearthed in the Lancashire Record Office. The treatise, in manuscript form and written in 1640, deals with the controversy over the long-term impact of the Julian Calendar - then in use in England - upon the ecclesiastical dating of Easter. By Crabtree's time, the timing of the Easter celebration in England was often several weeks adrift of the intentions of the early Church Fathers. The Gregorian Calendar, which Roman Catholic countries had adopted as long ago as 1582 in order to resolve the problem, was still vehemently resisted by the English state. This is possibly the only surviving manuscript in Crabtree's own hand. In it, he displays noteworthy dispassionate objectivity as he outlines the astronomical basis for the Easter date and explains why it has gone awry.

  13. Evaluation of the commercial FBR introduction date

    International Nuclear Information System (INIS)

    White, M.K.; Merrill, E.T.

    1981-09-01

    This report examines one criterion for introducing a commercial FBR: economic competitiveness with a Light Water Reactor (LWR). For this analysis, the commercial FBR is assumed to be the fifth-of-a kind replicate which represents an economically mature plant. This FBR is deemed economically competitive when its life-cycle energy cost is less than or equal to that of an LWR. Results of this analysis are used in a comparative analysis of alternative FBR development stategies. The strategies evaluated in these studies assume both 1000- and 1457-MWe FBRs. Since the capital costs per kilowatt, and therefore the energy costs, for these two FBR sizes are different, they will become economically competitive at different times. The probability density function for the 1457-MW(e) FBR has an expected value date or weighted average date of 2030, compared with 2033 for the probability density function for the 1000-MW(e) FBR

  14. Carbon-14 Bomb-Pulse Dating

    Energy Technology Data Exchange (ETDEWEB)

    Buchholz, B A

    2007-12-16

    Atmospheric testing of nuclear weapons during the 1950s and early 1960s doubled the concentration of carbon-14 atmosphere and created a pulse that labeled everything alive in the past 50 years as carbon moved up the food chain. The variation in carbon-14 concentration in time is well-documented and can be used to chronologically date all biological materials since the mid-1950s.

  15. Radiocarbon dating for the Quaternary scientist

    International Nuclear Information System (INIS)

    Pilcher, J.R.

    1991-01-01

    The accuracy of many conventional and accelerator mass spectrometry (AMS) radiocarbon dates is not adequate for the sort of questions now being asked in Quaternary studies. The need for, and effects of, radiocarbon calibration are discussed and guide-lines offered for the selection of a laboratory. High precision laboratories and the use of wiggle matching will go a long way to answering the critical questions of rates of change and durations of events in the Holocene. (Author)

  16. Progress and problems with automated TL dating

    International Nuclear Information System (INIS)

    McKerrell, H.; Mejdahl, V.

    1981-01-01

    A number of basic problems connected with the measurement of beta and gamma dose-rates are discussed, and the possibility of using low-temperature peaks in quartz and feldspar for dose-rate measurements is examined. Preliminary results of TL measurements on individual grains of quartz and feldspar are presented. A TL dating method based on the difference in the archaeological dose received by potassium feldspar and quartz grains is proposed. (author)

  17. {sup 14}C AMS dating Yongcheon cave

    Energy Technology Data Exchange (ETDEWEB)

    Lee, J.H., E-mail: jefflee@snu.ac.kr [AMS Lab., NCIRF, Seoul National University, Seoul 151-742 (Korea, Republic of); Choe, K. [AMS Lab., NCIRF, Seoul National University, Seoul 151-742 (Korea, Republic of); Kim, J.C. [Dept. of Physics and Astronomy, Seoul National University, Seoul 151-742 (Korea, Republic of); Choi, S.H.; Kang, J.; Song, S.; Song, Y.M. [AMS Lab., NCIRF, Seoul National University, Seoul 151-742 (Korea, Republic of); Jang, J.G. [Jeju National Museum, Jeju 690-782 (Korea, Republic of)

    2013-01-15

    The biggest island in South Korea is Jeju Island, which lies 80 km south of the mainland and has one shield volcano, Mt. Halla. The volcanic island and its lava tubes were added to the world heritage list by UNESCO in 2007. Among the many lava tubes on the island, a unique cave had been accidentally found in 2005 while some workers were replacing a telephone pole. Until the discovery, it had been completely isolated from the outside by naturally-built sand blocks. Yongcheon cave is a lime-decorated lava tube showing both the properties of a volcanic lava tube and a limestone cave. This cave, about 3 km in length, is acknowledged to be the best of this type in the world and includes a large clean-water lake, lava falls, and richly developed speleothems inside it. Even though there is archaeological evidence from well preserved pottery that ancient people entered this place, the preservation of artifacts was ensured by a geological change that made later entrance difficult. We have collected charcoal samples scattered around the cave and dated them using AMS. Ages were in the range of ca. 1570-1260 BP (A.D. 340-880) and this corresponds to the Ancient Three Kingdoms and the Unified Silla era in Korean history. The {sup 14}C AMS measurement results presented in this paper on wood charcoal provide precise dates which will be very useful not only to clarify the nature of human activities in this cave but also to provide reference dates when comparing other dating methods.

  18. 14C AMS dating Yongcheon cave

    International Nuclear Information System (INIS)

    Lee, J.H.; Choe, K.; Kim, J.C.; Choi, S.H.; Kang, J.; Song, S.; Song, Y.M.; Jang, J.G.

    2013-01-01

    The biggest island in South Korea is Jeju Island, which lies 80 km south of the mainland and has one shield volcano, Mt. Halla. The volcanic island and its lava tubes were added to the world heritage list by UNESCO in 2007. Among the many lava tubes on the island, a unique cave had been accidentally found in 2005 while some workers were replacing a telephone pole. Until the discovery, it had been completely isolated from the outside by naturally-built sand blocks. Yongcheon cave is a lime-decorated lava tube showing both the properties of a volcanic lava tube and a limestone cave. This cave, about 3 km in length, is acknowledged to be the best of this type in the world and includes a large clean-water lake, lava falls, and richly developed speleothems inside it. Even though there is archaeological evidence from well preserved pottery that ancient people entered this place, the preservation of artifacts was ensured by a geological change that made later entrance difficult. We have collected charcoal samples scattered around the cave and dated them using AMS. Ages were in the range of ca. 1570-1260 BP (A.D. 340–880) and this corresponds to the Ancient Three Kingdoms and the Unified Silla era in Korean history. The 14 C AMS measurement results presented in this paper on wood charcoal provide precise dates which will be very useful not only to clarify the nature of human activities in this cave but also to provide reference dates when comparing other dating methods.

  19. Dating cremated bone: the scientific background

    Directory of Open Access Journals (Sweden)

    Lanting, J. N.

    1999-12-01

    Full Text Available A new method of obtaining absolute chronology dates out of burnt or cremated bone is presented. The authors explain their recent experiments and give promising results.

    Los autores presentan un nuevo método para obtener fechas de datación absoluta a partir de restos de hueso sometidos a diferentes grados de combustión y explican algunas de sus recientes experiencias y los resultados obtenidos.

  20. Violence in dating: An update for adolescence

    OpenAIRE

    Valdivia Peralta, Maruzzella Paola; González Bravo, Luis Antonio

    2014-01-01

    This literature review updates evidence about intimate partner violence in dating relationships, revealing a particular phenomenon, emphasizing issues such as the prevalence for both sexes, which according to various reviewed studies may range from 0.8% for sexual violence to 98% for psychological aggression. Factors associated with abuse or early sexual initiation, temporal extent of the relationship, role of parents and peers, among others; and the consequences as dropouts: teenage pregnanc...

  1. Date Sensitive Computing Problems: Understanding the Threat

    Science.gov (United States)

    1998-08-29

    equipment on Earth.3 It can also interfere with electromagnetic signals from such devices as cell phones, radio, televison , and radar. By itself, the ...spacecraft. Debris from impacted satellites will add to the existing orbital debris problem, and could eventually cause damage to other satellites...Date Sensitive Computing Problems Understanding the Threat Aug. 17, 1998 Revised Aug. 29, 1998 Prepared by: The National Crisis Response

  2. Progress in ESR dating of fossils

    International Nuclear Information System (INIS)

    Ikeya, M.

    1983-01-01

    In this review the progress of ESR dating is briefly described together with its historical development. Examples of fossil dating include shells and corals in geological sediments, fossil bones and teeth in anthropology and fossil woods in geology. The total dose of natural radiation (TD) equivalent to the archaeological dose in TL dating was obtained by the additive dose method. Initially, the TDs were plotted against the known ages; using the apparent annual dose-rate thus obtained gives the ESR age within a factor of 2 or 3 for a fossil. Precise assessment of the radiation environment was made later taking the disequilibrium of uranium series disintegration into account. ESR ages of corals agreed well with those obtained by radiocarbon and uranium-thorium methods. The time-independent accumulation rate or a linear accumulation or uranium was adopted as a first sensible model for the opensystem fossil bones: the relation between the TD and the age explains the ages of anthropologically important bones. Lastly, geological assessment of fossil woods was made by ESR based on the organic radicals and electron traps in the silicified part. (author)

  3. Dates as raw material for agricultural distilleries

    Energy Technology Data Exchange (ETDEWEB)

    Laczynski, B

    1971-01-01

    Pit-containing dates had 88.0 to 89.2% dry matter, 41.7 to 47.5% sucrose, and 2.1 to 2.9% total protein. The mechanical broken charges of raw material were steamed, dispersed to a suspension of 15 to 17/sup 0/ Balling and pH 4.8 to 5.0, enriched with P and N, inoculated with 5 to 7 % of yeast suspension, and acidified to pH > 3.5. Thermophilic yeast cultivated at 27/sup 0/ and fermented below 30/sup 0/ for 2 days gave best results. The fermented liquor had a pH > 3.5, apparent density of 2.0/sup 0/, and contained 7.5 to 9.0 EtOH. From 100 kg dates were obtained 280 t0 340 l of the 15 to 17/sup 0/ dispersion and 320 to 360 l residue containing (per l) 6.0 to 8.5 g protein and 0.04 oat units. EtOH yield (l/quintal) was 914 for potatoes, 28.54 for molasses, 36.29 for cereals, 25.15 for dates, and 18.53 for malt.

  4. Preference Versus Choice in Online Dating.

    Science.gov (United States)

    Whyte, Stephen; Torgler, Benno

    2017-03-01

    This study explores factors that influence matches of online dating participants' stated preference for particular characteristics in a potential partner and compares these with the characteristics of the online daters actually contacted. The nature of online dating facilitates exploration of the differences between stated preference and actual choice by participants, as online daters willingly provide a range of demographics on their ideal partner. Using data from the Australian dating website RSVP, we analyze 219,013 contact decisions. We conduct a multivariate analysis using the number of matched variables between the participants' stated preference and the characteristics of the individuals contacted. We find that factors such as a person's age, their education level, and a more social personality all increase the number of factors they choose in a potential partner that match their original stated preference. Males (relative to females) appear to match fewer characteristics when contacting potential love interests. Conversely, age interaction effects demonstrate that males in their late 60's are increasingly more selective (than females) regarding who they contact. An understanding of how technology (the Internet) is impacting human mating patterns and the psychology behind the participants informs the wider social science of human behavior in large-scale decision settings.

  5. Radiocarbon C-14 dating - MINT experience

    International Nuclear Information System (INIS)

    Kamisah Alias

    2002-01-01

    The measurement of a radiocarbon date is a complex process which involved all the stages from advice given prior to submission of samples right through to reporting of results. The aim of our radiocarbon dating is to determine the residual 14 C content of a sample, the value of which is translated into an age that is an estimate of the time elapsed since the given sample was removed from the environment in which it had formed in equilibrium with respect to 14-C radioactive decay and metabolic assimilation. Carbon is obtained from carbon containing samples in the form of carbon dioxide, which is then reacted with lithium forming lithium carbide. The carbide is then hydrolysed to acetylene before it was polymerised to benzene using a high-efficiency vanadium-alumina-silica catalyst to produce benzene with up to 96% yield. Sample, background and modem standard activities are measured with a coincidence scintillation counter using in glass vials of 21 ml capacity. An improved chemical procedure was used to obtain and purify the benzene from the samples for measurement using a liquid scintillation counter. Radiocarbon dating measurements of samples collected reveal some results. The validity of the data have yet to be confirmed by the results of the measurements on two international control samples. (Author)

  6. Low energy cyclotron for radiocarbon dating

    International Nuclear Information System (INIS)

    Welch, J.J.

    1984-12-01

    The measurement of naturally occurring radioisotopes whose half lives are less than a few hundred million years but more than a few years provides information about the temporal behavior of geologic and climatic processes, the temporal history of meteoritic bodies as well as the production mechanisms of these radioisotopes. A new extremely sensitive technique for measuring these radioisotopes at tandem Van de Graaff and cyclotron facilities has been very successful though the high cost and limited availability have been discouraging. We have built and tested a low energy cyclotron for radiocarbon dating similar in size to a conventional mass spectrometer. These tests clearly show that with the addition of a conventional ion source, the low energy cyclotron can perform the extremely high sensitivity 14 C measurements that are now done at accelerator facilities. We found that no significant background is present when the cyclotron is tuned to accelerate 14 C negative ions and the transmission efficiency is adequate to perform radiocarbon dating on milligram samples of carbon. The internal ion source used did not produce sufficient current to detect 14 C directly at modern concentrations. We show how a conventional carbon negative ion source, located outside the cyclotron magnet, would produce sufficient beam and provide for quick sampling to make radiocarbon dating milligram samples with a modest laboratory instrument feasible

  7. Environmental history and dating of coastal dunefields

    International Nuclear Information System (INIS)

    Illenberger, W.K.; Verhagen, B.T.

    1990-01-01

    Sand pulses can be inferred from the geomorphologic evolution of coastal dunefields over the last 6500 years in the eastern Cape Province, South Africa. These pulses correlate with erosion cycles and variation in sea-level, temperature and effective moisture. The concept that sand dunes have a wind memory and represent a record of the wind that blew to produce them can be modified and applied to dunefields: the morphology of dunefields represents an environmental record, going back thousands of years. The carbonate content of eastern Cape coastal sands is biogenic with young coarse carbonate grains constantly being added to the system, resulting in a pronounced negative correlation of radiocarbon age with grain size. It takes thousands of years for an average mollusc shell to be broken to 1-mm-diameter fragments, and a further couple of thousand years to break these sizes down to 0.2-0.3 mm diameter. Eastern Cape coastal dunefields have for the first time been dated definitively via the radiocarbon ages of the carbonate component of the sand. These dunefields have been forming during the past 5000 years or so. Dating wind-blown sand transport is feasible, and correlates with dates inferred from the dunefield morphology. 5 figs., 1 tab., 18 refs

  8. Production of baker's yeast using date juice.

    Science.gov (United States)

    Beiroti, A; Hosseini, S N

    2007-07-01

    Baker's yeast is an important additive among the products which improves bread quality and for present time is being produced in different countries by batch, fed batch or continuous cultures. Saccharomyces cerevisiae is used in fermentation of starch in dough, giving a favourable taste and produces a variety of vitamins and proteins. The main ingredient in yeast production is carbon source such as beet molasses, cane molasses, and so on. Since beet molasses has other major function as in high yield alcohol production and also due to the bioenvironmental issues and related wastewater treatment, the use of other carbohydrate sources may be considered. One of these carbohydrate sources is date which is wasted a great deal annually in this country (Iran) . In this study, the capability of date to act as a suitable carbon sources was investigated. The waste date turned into juice and consequently production and growth rate of Sacchromyces cervisiae were studied with this juice. A maximum possible yield of 50% was obtained by the optimum medium (P3), at pH 3.4, 30 degrees C, 1.4 vvm aeration rate and agitation of 500 r/min.

  9. Irradiation positions for fission-track dating in the University of Pavia TRIGA Mark II nuclear reactor

    International Nuclear Information System (INIS)

    Oddone, Massimo; Meloni, Sandro; Balestrieri, Maria Laura; Bigazzi, Giulio

    2002-01-01

    An irradiation position arranged is described in the present paper for fission-track dating in the Triga Mark II reactor of the University of Pavia. Fluence values determined using the NIST glass standard SRM 962a for fission-track dating and the traditional metal foils are compared. Relatively good neutron thermalization (φ th /φ f = 0.956) and lack of significant fluence spatial gradients are good factors for fission-track dating. Finally, international age standards (or putative age standards) irradiated in this new position yielded results consistent with independent reference ages. (author)

  10. Cooling history of the Valles Caldera, New Mexico using ESR dating method

    International Nuclear Information System (INIS)

    Ogoh, K.; Toyoda, S.; Ikeda, S.; Ikeya, M.; Goff, F.

    1993-01-01

    ESR dating was made at the Valles caldera by using the Al center and Ti center in quartz grains separated from the layers of the Valles Rhyolite. Obtained ESR ages were much younger than those by other methods (fission track and 39 Ar- 40 Ar). A reported thermal event of about 10-40 ka ago might explain the difference between the above ages. (author)

  11. 17 CFR 232.13 - Date of filing; adjustment of filing date.

    Science.gov (United States)

    2010-04-01

    ..., shall not affect the date of filing. (2) If the conditions of paragraph (a)(1) of this section are... and consistent with the public interest and the protection of investors. (c) Payment of fees. Fees...

  12. 12 CFR 717.28 - Effective date, compliance date, and prospective application.

    Science.gov (United States)

    2010-01-01

    ... REGULATIONS AFFECTING CREDIT UNIONS FAIR CREDIT REPORTING Affiliate Marketing § 717.28 Effective date... eligibility information that you receive from an affiliate to make solicitations to a consumer if you receive...

  13. 12 CFR 334.28 - Effective date, compliance date, and prospective application.

    Science.gov (United States)

    2010-01-01

    ... REGULATIONS AND STATEMENTS OF GENERAL POLICY FAIR CREDIT REPORTING Affiliate Marketing § 334.28 Effective date... eligibility information that you receive from an affiliate to make solicitations to a consumer if you receive...

  14. U-Pb Dating of Zircons and Phosphates in Lunar Meteorites, Acapulcoites and Angrites

    Science.gov (United States)

    Zhou, Q.; Zeigler, R. A.; Yin, Q. Z.; Korotev, R. L.; Joliff, B. L.; Amelin, Y.; Marti, K.; Wu, F. Y.; Li, X. H.; Li, Q. L.; hide

    2012-01-01

    Zircon U-Pb geochronology has made a great contribution to the timing of magmatism in the early Solar System [1-3]. Ca phosphates are another group of common accessory minerals in meteorites with great potential for U-Pb geochronology. Compared to zircons, the lower closure temperatures of the U-Pb system for apatite and merrillite (the most common phosphates in achondrites) makes them susceptible to resetting during thermal metamorphism. The different closure temperatures of the U-Pb system for zircon and apatite provide us an opportunity to discover the evolutionary history of meteoritic parent bodies, such as the crystallization ages of magmatism, as well as later impact events and thermal metamorphism. We have developed techniques using the Cameca IMS-1280 ion microprobe to date both zircon and phosphate grains in meteorites. Here we report U-Pb dating results for zircons and phosphates from lunar meteorites Dhofar 1442 and SaU 169. To test and verify the reliability of the newly developed phosphate dating technique, two additional meteorites, Acapulco, obtained from Acapulco consortium, and angrite NWA 4590 were also selected for this study as both have precisely known phosphate U-Pb ages by TIMS [4,5]. Both meteorites are from very fast cooled parent bodies with no sign of resetting [4,5], satisfying a necessity for precise dating.

  15. Proterozoic biotite Rb-Sr dates in the northwestern part of the Yilgarn Craton, Western Australia

    International Nuclear Information System (INIS)

    Libby, W.G.; De Laeter, J.R.; Armstrong, R.A.

    1999-01-01

    Rb-Sr dating of biotite in the northwestern corner of the Yilgarn Craton identified four areas with distinctive age ranges. Biotite in the northwestern area, which includes the Narryer Terrane and part of the Murchison Terrane, yields reset Rb-Sr dates of ca 1650 Ma. In the western area, along the margin of the craton, biotite has been reset to 629 Ma. Eastward of these areas, mainly in the Murchison Terrane, the modal biotite date is near 2450 Ma, though because of a skewed distribution the mean date is closer to 2300 Ma. Dates in a transition zone between the western and eastern areas range broadly between 2000 and 1000 Ma, averaging about 1775 Ma. The western area and the transition zone are continuous with analogous areas south of the limits of the present study. The 1650 Ma dates in the northwestern area are probably related to plutonic and tectonic activity of similar age in the Gascoyne Province to the north. They may represent cooling after thermal resetting during tectonic loading by southward thrust-stacking of slices of Narryer Terrane and allochthonous Palaeoproterozoic volcanic arc and back arc rocks during the Capricorn Orogeny. This episode of crustal shortening resulted from the collision of the Yilgarn and Pilbara Cratons to form the West Australian Craton. The dates reflect cooling associated with subsequent erosion-induced rebound. The 2450 Ma biotite dates of the eastern area are similar to biotite dates found over most of the Yilgarn Craton and represent a background upon which the later dates have been superimposed. The origin of dates in the western area is unknown but may be related to an associated dolerite dyke swarm or to possible thrusting from the west. There is some evidence of minor later intrusion of felsic hypabyssal rock between 2000 and 2200 Ma and localised shearing in the Narryer area at about 1350 to 1400 Ma. One small area near Yalgoo with biotite Rb-Sr dates near 2200 Ma may be co genetic with the Muggamurra Swarm of dolerite

  16. Silicon isotope study of thermal springs in Jiaodong Region,Shandong Province

    Institute of Scientific and Technical Information of China (English)

    徐跃通; 李红梅; 冯海霞; 周晨; 吴元芳; 张邦花

    2001-01-01

    Based on δ30Si and δ32Si isotope geochemistry, the origin and evolutionary mechanism of thermal springs in Jiaodong region are studied. The mean value of δ30Si of dissolved silica of thermal spring water in Jiaodong is 0.1‰. Thermal spring water ages using δ32Si dating method range from 387a to 965a.

  17. 24 CFR 220.811 - Date of default.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Date of default. 220.811 Section... and Obligations-Projects Insured Project Improvement Loans § 220.811 Date of default. For the purposes of §§ 220.800 et seq., the date of default shall be considered as: (a) The date of the first...

  18. Date fruit: chemical composition, nutritional and medicinal values, products.

    Science.gov (United States)

    Tang, Zhen-Xing; Shi, Lu-E; Aleid, Salah M

    2013-08-15

    Date fruit has served as a staple food in the Arab world for centuries. Worldwide production of date fruit has increased almost threefold over the last 40 years, reaching 7.68 million tons in 2010. Date fruit can provide many essential nutrients and potential health benefits to the consumer. Date fruit goes through four ripening stages named kimri, khalal, rutab and tamer. The main chemical components of date fruit include carbohydrates, dietary fibre, enzymes, protein, fat, minerals, vitamins, phenolic acids and carotenoids. The chemical composition of date fruit varies according to ripening stage, cultivar, growing environment, postharvest conditions, etc. The nutritional and medicinal activities of date fruit are related to its chemical composition. Many studies have shown that date fruit has antioxidant, antimutagenic, anti-inflammatory, gastroprotective, hepatoprotective, nephroprotective, anticancer and immunostimulant activities. Various date fruit-based products such as date syrup, date paste, date juice and their derived products are available. Date by-products can be used as raw materials for the production of value-added products such as organic acids, exopolysaccharides, antibiotics, date-flavoured probiotic-fermented dairy produce, bakery yeasts, etc. In this paper the chemical composition and nutritional and medicinal values of date fruit as well as date fruit-based products are reviewed. © 2013 Society of Chemical Industry.

  19. Dating Violence among High School Students in Southeastern North Carolina

    Science.gov (United States)

    Kim-Godwin, Yeoun Soo; Clements, Carrie; McCuiston, Ashley M.; Fox, Jane A.

    2009-01-01

    Adolescents are a high-risk group for dating violence. Using the Youth Risk Behavior Survey data, this study examined the associations among dating violence (including physical dating violence [PDV] and sexual dating violence [SDV]) and selected health risk behaviors among 375 and 372 high school students, in 2005 and 2007, respectively, in…

  20. 7 CFR 35.8 - Date of export.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Date of export. 35.8 Section 35.8 Agriculture... Practices), DEPARTMENT OF AGRICULTURE COMMODITY STANDARDS AND STANDARD CONTAINER REGULATIONS EXPORT GRAPES AND PLUMS Definitions § 35.8 Date of export. Date of export means the date of loading on board the...

  1. 21 CFR 610.50 - Date of manufacture.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Date of manufacture. 610.50 Section 610.50 Food... GENERAL BIOLOGICAL PRODUCTS STANDARDS Dating Period Limitations § 610.50 Date of manufacture. The date of manufacture shall be determined as follows: (a) For products for which an official standard of potency is...

  2. Uses of radiocarbon dating in archaeology

    International Nuclear Information System (INIS)

    Purohit, Anila; Bishnoi, Indra; Charan, Sumitra

    2012-01-01

    Carbon dating is one of the mist effective tools in the archaeologist's kit. It has provided illumination where none was once thought possible. The historians of one hundred years ago could only dream of such a wonderful, albeit frightening atomic clock ticking away, helping to mark the passing of the years and the ages of man. It is a vital part in the investigation and preservation of our past and a lovely bit of analysis to compliment digital records of monuments. It places the plants, animals, and people of yore into an understandable and verifiable context

  3. Dating method with /sup 39/Ar

    Energy Technology Data Exchange (ETDEWEB)

    Loosli, H H [Bern Univ. (Switzerland). Physikalisches Inst.

    1983-04-01

    The principles of a dating method based on the cosmic-ray-produced radioisotope /sup 39/Ar are given. Technical requirements such as background and standard gas samples and gas proportional counting systems are described. With samples extracted from Greenland ice it can be demonstrated that /sup 39/Ar ages agree with ages obtained by other methods. First results on ocean water samples show that with this isotope valuable information on ocean mixing and circulation can be expected. /sup 39/Ar results on groundwater samples disagree for some aquifers with conventional /sup 14/C ages; possible explanations are discussed, especially underground production of /sup 39/Ar.

  4. Radiocarbon dating prehistoric pottery from Northern Europe

    DEFF Research Database (Denmark)

    Philippsen, Bente; Craig, Oliver; Heron, Carl

    2012-01-01

    , such as when aquatic products have been prepared in the pottery. Soot can derive from old wood that was used for the hearth fire, or from (potentially aquatic) food that boiled over. Plant remains may have been present in the clay for a long time before manufacture of the pottery. Post......-depositional contamination with organic carbon, such as humic acids, may also be problematic. We present these data with radiocarbon datings of contemporaneous terrestrial and aquatic samples to find out the true age of the pottery and estimate the reservoir age. Lipid analysis and bulk carbon and nitrogen stable isotope...

  5. Suitability of Ostrich eggshell for radiocarbon dating

    CSIR Research Space (South Africa)

    Vogel, JC

    2001-01-01

    Full Text Available deposits cannot be guaranteed. A more direct approach would be to ana- lyze modern ostrich eggs of which the date of laying is known. It is necessary to know exactly when the eggs were laid because the elevated 14C content of the environment caused... sample we also analyzed the organic contents of the egg—a mixture of the egg white and yolk. Also given is the 14C content of the carbon dioxide of the atmosphere in the month in which the eggs were laid. This closely reflects the 14C content...

  6. Zechariah and the Dating of Biblical Hebrew

    DEFF Research Database (Denmark)

    Ehrensvärd, Martin Gustaf

    2006-01-01

    The data presented in the article indicate clearly that the ability to write proper EBH did not end with the exile; but when did it end? In the course of the fifth century, or the fourth century, or even later? This is difficult to resolve, on linguistic grounds. On linguistic grounds, can we say...... conclusions of most biblical scholars. Considering only linguistic data, texts in EBH could have been composed after the exile. Other, non-linguistic considerations can make this unlikely, but we can raise no objections from a linguistic viewpoint to such a dating....

  7. Thermoluminescence dating of some Hungarian medieval churches

    International Nuclear Information System (INIS)

    Kasa, I.; Bajnoczy, G.

    1984-01-01

    Thermoluminescence dating of three Hungarian historic churches was performed using the quarz inclusion technique and sup(60)Co gamma irradiation. Quarz grains obtained from the bricks were irradiated and the radiation doses were measured by CaSOsub(4):Dy TL dosemeters. Glow curves of irradiated and non-irradiated samples were also measured. From the results it was concluded that the ages of two churches were 10 and 30 percent less, respectively, than the ages estimated earlier. The age of the third church proved to be correct. (R.P.)

  8. Optically stimulated luminescence dating of rock surfaces

    DEFF Research Database (Denmark)

    Sohbati, Reza

    There are many examples of rock surfaces, rock art and stone structures whose ages are of great importance to the understanding of various phenomena in geology, climatology and archaeology. Optically stimulated luminescence (OSL) dating is a well-established chronological tool that has successfully...... to include the effects of the environmental dose rate. By fitting the model to the dose-depth variation from a single clast, four events (two light exposures of different durations each followed by a burial period) in the history of a single cobble are identified and quantified. However, the use of model...

  9. Magnetic inclination from Brazilian bricks and application to Archeomagnetic dating

    Science.gov (United States)

    Begnini, G. S.; Hartmann, G. A.; Trindade, R. I.

    2013-05-01

    The Earth's magnetic field (EMF) is recorded in archeological baked materials carrying a stable remanent magnetization. This magnetic record can be used for indirectly date the archeological material by comparison with "reference curves" of the EMF. In this work we present magnetic inclination data from two different sites in southeastern Brazil, an ancient and a modern one: (a) a sampling at the ancient sugarcane mill Engenho Central de Piracicaba (ECP, 1881-1974 AD), and (b) a controlled survey at the modern brickyard Olaria Schiavolin (OS). Both of them are located in the city of Piracicaba, São Paulo State, Brazil. Magnetic measurements included stepwise thermal and alternating field demagnetization, anisotropy of magnetic susceptibility (AMS) and low-field magnetic susceptibility vs. temperature. In OS, we collected 40 oriented bricks from 5 sampling points inside the brickyard oven in order to test the stability and reliability of their remanent magnetizations by comparing them with the local field (measured directly with a fluxgate magnetometer). We observed differences of +/- 3° between the local field and the IGRF. When magnetic inclinations are reported relative to the flat planes of the brick (the situation we face for real ancient bricks), the differences due to inclination of the burning plane and magnetic anomalies inside the oven never exceed 6°. These differences are averaged out by using a minimum of 6 bricks (~24 specimens) per sampling point to compute the inclination. In the ancient site ECP we collected 140 non-oriented bricks from 14 different walls; three of them were previously dated using historical records. Inclinations were defined using at least 6 bricks per wall, showing consistent average values within the same walls. When compared to the IGRF and GUFM1 models, the inclinations obtained for the dated walls agreed within the experimental error. We have then applied the same procedure to estimate the age of the remaining walls. Using

  10. K/Ar dating of diagenetic illites

    International Nuclear Information System (INIS)

    Mizusaki, A.M.P.; Anjos, S.M.C. dos; Costa, M.G.F. da; Silva, O.B. da; Kawashita, K.

    1990-01-01

    Ascertaining the potassium/argon (K/Ar) age of diagenetic illites yields important information for hydrocarbon exploration since the growth of this mineral in the pores of sandstone reservoir and oil migration are interlinked events in the diagenetic evolution of rocks. Illite growth ceases as soon as hydrocarbons completely fill in rock pores, displacing interstitial water. By providing an estimate of the period when the illite formed, K/Ar dating can indirectly tells us when hydrocarbons entered the reservoir. Samples of oil-saturated sandstones collected from Carboniferous reservoirs of the Solimoes Basin reveal a diagenetic evolution consisting predominantly of quartz, calcite, and illite overgrowths. In the present study, illite was mechanically separated by repeating a series of ultrasonic baths and ultrasonic probes followed by high-speed centrifuging. Resultant fractions were analyzed by X-ray diffractometry to measure the illite content of each sample. The separated illite material was found to be composed of illite and ordered mixed layer illite-smectite with 80% illite layers. Separated fractions were dated radiometrically by the K/Ar method. Preliminary results indicate an average age of some 200 m.y., which marks the end of the diagenetic development of the illites of this area. (author)

  11. Comparison of gestational dating methods and implications ...

    Science.gov (United States)

    OBJECTIVES: Estimating gestational age is usually based on date of last menstrual period (LMP) or clinical estimation (CE); both approaches introduce potential bias. Differences in methods of estimation may lead to misclassificat ion and inconsistencies in risk estimates, particularly if exposure assignment is also gestation-dependent. This paper examines a'what-if' scenario in which alternative methods are used and attempts to elucidate how method choice affects observed results.METHODS: We constructed two 20-week gestational age cohorts of pregnancies between 2000 and 2005 (New Jersey, Pennsylvania, Ohio, USA) using live birth certificates : one defined preterm birth (PTB) status using CE and one using LMP. Within these, we estimated risk for 4 categories of preterm birth (PTBs per 106 pregnancies) and risk differences (RD (95% Cl s)) associated with exposure to particulate matter (PM2. 5).RESULTS: More births were classified preterm using LMP (16%) compared with CE (8%). RD divergences increased between cohorts as exposure period approached delivery. Among births between 28 and 31 weeks, week 7 PM2.5 exposure conveyed RDs of 44 (21 to 67) for CE and 50 (18 to 82) for LMP populations, while week 24 exposure conveyed RDs of 33 (11 to 56) and -20 (-50 to 10), respectively.CONCLUSIONS: Different results from analyses restricted to births with both CE and LMP are most likely due to differences in dating methods rather than selection issues. Results are sensitive t

  12. Palaeo-poo: date from rat scats

    International Nuclear Information System (INIS)

    Pearson, S.; Department of Geography.

    1997-01-01

    AMS dating has allowed a detailed study of the stratigraphy of stick-nest rat (Leporillus spp.) middens. The results of multiple dates on apparently the same layers of the middens show that the taphonomy of the midden is complex. Nevertheless, the information recovered from this source is an exciting addition to understanding arid ecosystems. Information about the local and regional vegetation, possible CO 2 -induced changes in stomata, distribution of mammals and their predator-prey relations has been recovered from the middens. Palaeoecological information coming from the arid zone has been limited but this source provides a breakthrough in providing direct and detailed ecological information. This helps contextualise the late Holocene increase in arid zone archaeological site visibility. It emphasises the pattern of arid zone mammal losses. It provides important corroborating evidence to other palaeoecological records. It is emphasised that the deposits containing pollen and macrofossils are datable using radiocarbon but there are some serious problems in providing ecological information from stick-nest rat middens

  13. The Rate of Cyber Dating Abuse among Teens and How It Relates to Other Forms of Teen Dating Violence

    Science.gov (United States)

    Zweig, Janine M.; Dank, Meredith; Yahner, Jennifer; Lachman, Pamela

    2013-01-01

    To date, little research has documented how teens might misuse technology to harass, control, and abuse their dating partners. This study examined the extent of cyber dating abuse--abuse via technology and new media--in youth relationships and how it relates to other forms of teen dating violence. A total of 5,647 youth from ten schools in three…

  14. Dating Norms and Dating Violence among Ninth Graders in Northeast Georgia: Reports from Student Surveys and Focus Groups

    Science.gov (United States)

    Reeves, Patricia M.; Orpinas, Pamela

    2012-01-01

    This mixed-methods study describes the norms supporting male-to-female and female-to-male dating violence in a diverse sample of ninth graders. The quantitative study, based on student surveys (n = 624), compared norms supporting dating violence by sex, race/ethnicity, and dating status, and it examined the relation between dating violence norms…

  15. Thermal stress mitigation by Active Thermal Control

    DEFF Research Database (Denmark)

    Soldati, Alessandro; Dossena, Fabrizio; Pietrini, Giorgio

    2017-01-01

    This work proposes an Active Thermal Control (ATC) of power switches. Leveraging on the fact that thermal stress has wide impact on the system reliability, controlling thermal transients is supposed to lengthen the lifetime of electronic conversion systems. Indeed in some environments...... results of control schemes are presented, together with evaluation of the proposed loss models. Experimental proof of the ability of the proposed control to reduce thermal swing and related stress on the device is presented, too....

  16. Obsidian dating by fission track method

    International Nuclear Information System (INIS)

    Araya, A.M.O.

    1990-12-01

    The fission track method was employed to obtain the age of twelve obsidian sample from Ecuador. By using the plateau-age correction method, we obtained the true age of each sample and were able to identify four groups of ages in the studied area. Thereafter we studied the fading of fission tracks in two obsidian samples with different origins: Yanaurcu, Ecuador and Monte Arci, Italy. We constructed Arrhenius plots and calculated activation energies for both samples. The results from thermal annealing experiments were compared with theoretical curves obtained by integrating an equation proposed by Shukolyukov et al (1965). (author). 43 refs, 20 figs, 10 tabs

  17. New dates reignite human evolution debate

    International Nuclear Information System (INIS)

    Nolch, G.

    2000-01-01

    Australian research into the Asian fossil record is unearthing controversial evidence with implications for the evolution of humans. Dr Jian-xin Zhao and Prof Ken Collerson from the University of Queensland's Department of Earth Sciences have been studying the fossil record in East Asia for clues to the early migration of hominids out of Africa in collaboration with Chinese archaeologists Dr Kai Hu of Nanjing University and Hankui Xu of Nanjing Institute of Palaeontology, Academia Sinica. Together they have been studying the remains of Nanjing Man, the name given to two Homo erectus skulls and the tooth of a third individual discovered in Tangshan Cave 250 km north-west of Shanghai. Dr Zhao and Prof Collerson have now employed more accurate dating techniques and materials, using a mass spectrometer to analyse the amounts of thorium-230 and uranium-234 in a calcite flowstone above the Nanjing Man fossil bed. Unlike fossil teeth, uranium and thorium became locked into the flowstone's crystal lattice when the calcite became crystallised. Because of this, the U-series decay in the calcite reliably records when the calcite crystallised. Taking into account the half-lives of uranium-234 and thorium-230, Dr Zhao and Prof Collerson determined the age of the calcite flowstone to be 577,000 years old (+44,000/-34,000 years). As the flowstone overlies the fossil bed, this date only defines the minimum age of the Nanjing Man fossil bed. For comparison, the dentine and enamel components of one fossil deer tooth collected from the Nanjing Man fossil bed yielded discordant mass spectrometric U-series ages of 388,000 and 130,100 years, respectively. Dr Zhao says that this 'strongly demonstrates the unreliability of fossil teeth as a chronometer'. Other evidence in the sediments surrounding the fossils has been the presence of flora and fauna that are typical of a glacial period. Dr Zhao therefore believes that the skulls could have been deposited during a glacial period

  18. Dating mortars: three medieval Spanish architectures

    Directory of Open Access Journals (Sweden)

    Quirós Castillo, Juan Antonio

    2011-12-01

    Full Text Available One of the major issues in building archaeology is finding the age of elements and structures discovered. Mortars represent a class of material basically constituted by a mixture of different phases (i.e. binder, aggregates, water and are widely used for constructive uses and artworks. Current scientific literature regarding the possibility of accurate radiocarbon dating for mortars reports different and still contradictory results. In this study, a new protocol for radiocarbon dating of mortar developed at the Centre for Isotopic Research on Cultural and Environmental heritage (CIRCE is used to perform 14C measurements on archaeological mortars coming from three medieval architectures of northern Spain (two churches and the walls of a castle. Results observed will be discussed and compared with independent age estimations (i.e. radiocarbon dating performed on organic materials found in the same study site, archaeological analyses in order to frame experimental observations in the actual site knowledge by means of a multidisciplinary approach.Una de las principales problemáticas a las que se enfrenta la arqueología de la arquitectura es datar los elementos y las estructuras. Las argamasas son un tipo de material constituido por una mezcla de diferentes elementos (agregados, agua y empleadas en muchos tipos de construcciones. Los estudios realizados hasta la actualidad en torno a la posibilidad de realizar dataciones radiocarbónicas precisas han proporcionado resultados contradictorios. El objetivo de este artículo es el de presentar un nuevo protocolo para datar la arquitectura histórica desarrollado por el Centre for Isotopic Research on Cultural and Enviromental Heritage (CIRCE, basado en la realización de dataciones radiocarbónicas de argamasas a partir del análisis de tres arquitecturas medievales del norte del España, dos iglesias y la muralla de un castillo. Los resultados obtenidos han sido confrontados y comparados con otros

  19. Fourier diffraction theorem for diffusion-based thermal tomography

    International Nuclear Information System (INIS)

    Baddour, Natalie

    2006-01-01

    There has been much recent interest in thermal imaging as a method of non-destructive testing and for non-invasive medical imaging. The basic idea of applying heat or cold to an area and observing the resulting temperature change with an infrared camera has led to the development of rapid and relatively inexpensive inspection systems. However, the main drawback to date has been that such an approach provides mainly qualitative results. In order to advance the quantitative results that are possible via thermal imaging, there is interest in applying techniques and algorithms from conventional tomography. Many tomography algorithms are based on the Fourier diffraction theorem, which is inapplicable to thermal imaging without suitable modification to account for the attenuative nature of thermal waves. In this paper, the Fourier diffraction theorem for thermal tomography is derived and discussed. The intent is for this thermal-diffusion based Fourier diffraction theorem to form the basis of tomographic reconstruction algorithms for quantitative thermal imaging

  20. The Prototype HyspIRI Thermal Infrared Radiometer (PHyTIR): A High Speed, Multispectral, Thermal Instrument Development in Support of HyspIRI-TIR

    Science.gov (United States)

    Hook, Simon

    2011-01-01

    The Prototype HyspIRI Thermal Infrared Radiometer (PHyTIR) is being developed as part of the risk reduction activities associated with the Hyperspectral Infrared Imager (HyspIRI). The HyspIRI mission was recommended by the National Research Council Decadal Survey and includes a visible shortwave infrared (SWIR) pushboom spectrometer and a multispectral whiskbroom thermal infrared (TIR) imager. Data from the HyspIRI mission will be used to address key science questions related to the Solid Earth and Carbon Cycle and Ecosystems focus areas of the NASA Science Mission Directorate. The HyspIRI TIR system will have 60m ground resolution, better than 200mK noise equivalent delta temperature (NEDT), 0.5C absolute temperature resolution with a 5-day repeat from LEO orbit. PHyTIR addresses the technology readiness level (TRL) of certain key subsystems of the TIR imager, primarily the detector assembly and scanning mechanism. PHyTIR will use Mercury Cadmium Telluride (MCT) technology at the focal plane and operate in time delay integration mode. A custom read out integrated circuit (ROIC) will provide the high speed readout hence allowing the high data rates needed for the 5 day repeat. PHyTIR will also demonstrate a newly developed interferometeric metrology system. This system will provide an absolute measurement of the scanning mirror to an order of magnitude better than conventional optical encoders. This will minimize the reliance on ground control points hence minimizing post-processing (e.g. geo-rectification computations).