Optimization of sol-gel technique for coating of metallic substrates by hydroxyapatite using the Taguchi method

Science.gov (United States)

Pourbaghi-Masouleh, M.; Asgharzadeh, H.

2013-08-01

In this study, the Taguchi method of design of experiment (DOE) was used to optimize the hydroxyapatite (HA) coatings on various metallic substrates deposited by sol-gel dip-coating technique. The experimental design consisted of five factors including substrate material (A), surface preparation of substrate (B), dipping/withdrawal speed (C), number of layers (D), and calcination temperature (E) with three levels of each factor. An orthogonal array of L18 type with mixed levels of the control factors was utilized. The image processing of the micrographs of the coatings was conducted to determine the percentage of coated area ( PCA). Chemical and phase composition of HA coatings were studied by XRD, FT-IR, SEM, and EDS techniques. The analysis of variance (ANOVA) indicated that the PCA of HA coatings was significantly affected by the calcination temperature. The optimum conditions from signal-to-noise ( S/N) ratio analysis were A: pure Ti, B: polishing and etching for 24 h, C: 50 cm min-1, D: 1, and E: 300 °C. In the confirmation experiment using the optimum conditions, the HA coating with high PCA of 98.5 % was obtained.

Developing an optimum protocol for thermoluminescence dosimetry with gr-200 chips using Taguchi method

International Nuclear Information System (INIS)

Sadeghi, Maryam; Faghihi, Reza; Sina, Sedigheh

2017-01-01

Thermoluminescence dosimetry (TLD) is a powerful technique with wide applications in personal, environmental and clinical dosimetry. The optimum annealing, storage and reading protocols are very effective in accuracy of TLD response. The purpose of this study is to obtain an optimum protocol for GR-200; LiF: Mg, Cu, P, by optimizing the effective parameters, to increase the reliability of the TLD response using Taguchi method. Taguchi method has been used in this study for optimization of annealing, storage and reading protocols of the TLDs. A number of 108 GR-200 chips were divided into 27 groups, each containing four chips. The TLDs were exposed to three different doses, and stored, annealed and read out by different procedures as suggested by Taguchi Method. By comparing the signal-to-noise ratios the optimum dosimetry procedure was obtained. According to the results, the optimum values for annealing temperature (de.C), Annealing Time (s), Annealing to Exposure time (d), Exposure to Readout time (d), Pre-heat Temperature (de.C), Pre-heat Time (s), Heating Rate (de.C/s), Maximum Temperature of Readout (de.C), readout time (s) and Storage Temperature (de.C) are 240, 90, 1, 2, 50, 0, 15, 240, 13 and -20, respectively. Using the optimum protocol, an efficient glow curve with low residual signals can be achieved. Using optimum protocol obtained by Taguchi method, the dosimetry can be effectively performed with great accuracy. (authors)

Dry sliding wear behaviour of organo-modified montmorillonite filled epoxy nanocomposites using Taguchi's techniques

International Nuclear Information System (INIS)

Rashmi; Renukappa, N.M.; Suresha, B.; Devarajaiah, R.M.; Shivakumar, K.N.

2011-01-01

Highlights: → Successful fabrication of OMMT filled epoxy nanocomposites by high-shear mixing mehod. → Systematic tribological behaviour of the nanocomposites was made using Taguchi method. → Worn surface morphologies of the samples were discussed for different wear mechanisms. → Generation of wear data for sliding/bearing parts for different industries. -- Abstract: The aim of the research article is to study the dry sliding wear behaviour of epoxy with different wt.% of organo-modified montmorillonite (OMMT) filled nanocomposites. An orthogonal array (L 9 ) was used to investigate the influence of tribological parameters. The results indicate that the sliding distance emerges as the most significant factor affecting wear rate of epoxy nanocomposites. Experimental results showed that the inclusion of 5 wt.% OMMT nanofiller increased the wear resistance of the epoxy nanocomposite significantly. Furthermore, the worn surfaces of the samples were analyzed by scanning electron microscopy (SEM) to study the wear mechanisms and to correlate them with the wear test results.

Incorporating Servqual-QFD with Taguchi Design for optimizing service quality design

Science.gov (United States)

Arbi Hadiyat, M.

2018-03-01

Deploying good service design in service companies has been updated issue in improving customer satisfaction, especially based on the level of service quality measured by Parasuraman’s SERVQUAL. Many researchers have been proposing methods in designing the service, and some of them are based on engineering viewpoint, especially by implementing the QFD method or even using robust Taguchi method. The QFD method would found the qualitative solution by generating the “how’s”, while Taguchi method gives more quantitative calculation in optimizing best solution. However, incorporating both QFD and Taguchi has been done in this paper and yields better design process. The purposes of this research is to evaluate the incorporated methods by implemented it to a case study, then analyze the result and see the robustness of those methods to customer perception of service quality. Started by measuring service attributes using SERVQUAL and find the improvement with QFD, the deployment of QFD solution then generated by defining Taguchi factors levels and calculating the Signal-to-noise ratio in its orthogonal array, and optimized Taguchi response then found. A case study was given for designing service in local bank. Afterward, the service design obtained from previous analysis was then evaluated and shows that it was still meet the customer satisfaction. Incorporating QFD and Taguchi has performed well and can be adopted and developed for another research for evaluating the robustness of result.

Multi-response optimization of process parameters in friction stir welded AM20 magnesium alloy by Taguchi grey relational analysis

Directory of Open Access Journals (Sweden)

Prakash Kumar Sahu

2015-03-01

Full Text Available The purpose of this paper is to optimize the process parameter to get the better mechanical properties of friction stir welded AM20 magnesium alloy using Taguchi Grey relational analysis (GRA. The considered process parameters are welding speed, tool rotation speed, shoulder diameter and plunging depth. The experiments were carried out by using Taguchi's L18 factorial design of experiment. The processes parameters were optimized and ranked the parameters based on the GRA. The percentage influence of each process parameter on the weld quality was also quantified. A validation experimental run was conducted using optimal process condition, which was obtained from the analysis, to show the improvement in mechanical properties of the joint. This study also shows the feasibility of the GRA with Taguchi technique for improvement in welding quality of magnesium alloy.

Developing an Optimum Protocol for Thermoluminescence Dosimetry with GR-200 Chips using Taguchi Method.

Science.gov (United States)

Sadeghi, Maryam; Faghihi, Reza; Sina, Sedigheh

2017-06-15

Thermoluminescence dosimetry (TLD) is a powerful technique with wide applications in personal, environmental and clinical dosimetry. The optimum annealing, storage and reading protocols are very effective in accuracy of TLD response. The purpose of this study is to obtain an optimum protocol for GR-200; LiF: Mg, Cu, P, by optimizing the effective parameters, to increase the reliability of the TLD response using Taguchi method. Taguchi method has been used in this study for optimization of annealing, storage and reading protocols of the TLDs. A number of 108 GR-200 chips were divided into 27 groups, each containing four chips. The TLDs were exposed to three different doses, and stored, annealed and read out by different procedures as suggested by Taguchi Method. By comparing the signal-to-noise ratios the optimum dosimetry procedure was obtained. According to the results, the optimum values for annealing temperature (°C), Annealing Time (s), Annealing to Exposure time (d), Exposure to Readout time (d), Pre-heat Temperature (°C), Pre-heat Time (s), Heating Rate (°C/s), Maximum Temperature of Readout (°C), readout time (s) and Storage Temperature (°C) are 240, 90, 1, 2, 50, 0, 15, 240, 13 and -20, respectively. Using the optimum protocol, an efficient glow curve with low residual signals can be achieved. Using optimum protocol obtained by Taguchi method, the dosimetry can be effectively performed with great accuracy. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Improved Taguchi method based contract capacity optimization for industrial consumer with self-owned generating units

International Nuclear Information System (INIS)

Yang, Hong-Tzer; Peng, Pai-Chun

2012-01-01

Highlights: ► We propose an improved Taguchi method to determine the optimal contract capacities with SOGUs. ► We solve the highly discrete and nonlinear optimization problem for the contract capacities with SOGUs. ► The proposed improved Taguchi method integrates PSO in Taguchi method. ► The customer using the proposed optimization approach may save up to 12.18% of power expenses. ► The improved Taguchi method can also be well applied to the other similar problems. - Abstract: Contract capacity setting for industrial consumer with self-owned generating units (SOGUs) is a highly discrete and nonlinear optimization problem considering expenditure on the electricity from the utility and operation costs of the SOGUs. This paper proposes an improved Taguchi method that combines existing Taguchi method and particle swarm optimization (PSO) algorithm to solve this problem. Taguchi method provides fast converging characteristics in searching the optimal solution through quality analysis in orthogonal matrices. The integrated PSO algorithm generates new solutions in the orthogonal matrices based on the searching experiences during the evolution process to further improve the quality of solution. To verify feasibility of the proposed method, the paper uses the real data obtained from a large optoelectronics factory in Taiwan. In comparison with the existing optimization methods, the proposed improved Taguchi method has superior performance as revealed in the numerical results in terms of the convergence process and the quality of solution obtained.

SVM-RFE based feature selection and Taguchi parameters optimization for multiclass SVM classifier.

Science.gov (United States)

Huang, Mei-Ling; Hung, Yung-Hsiang; Lee, W M; Li, R K; Jiang, Bo-Ru

2014-01-01

Recently, support vector machine (SVM) has excellent performance on classification and prediction and is widely used on disease diagnosis or medical assistance. However, SVM only functions well on two-group classification problems. This study combines feature selection and SVM recursive feature elimination (SVM-RFE) to investigate the classification accuracy of multiclass problems for Dermatology and Zoo databases. Dermatology dataset contains 33 feature variables, 1 class variable, and 366 testing instances; and the Zoo dataset contains 16 feature variables, 1 class variable, and 101 testing instances. The feature variables in the two datasets were sorted in descending order by explanatory power, and different feature sets were selected by SVM-RFE to explore classification accuracy. Meanwhile, Taguchi method was jointly combined with SVM classifier in order to optimize parameters C and γ to increase classification accuracy for multiclass classification. The experimental results show that the classification accuracy can be more than 95% after SVM-RFE feature selection and Taguchi parameter optimization for Dermatology and Zoo databases.

Application of Taguchi methodology to improve the functional quality of a mechanical device

International Nuclear Information System (INIS)

Regeai, Awatef Omar

2005-01-01

Manufacturing and quality control are recognized branches of engineering management. special attention has been made to improve thr tools and methods for the purpose of improving the products quality and finding solutions for any Obstacles and/or problems during the production process. Taguchi methodology is one of the most powerful techniques for improving product and manufacturing process quality at low cost. It is a strategical and practical method that aims to assist managers and industrial engineers to tackle manufacturing quality problems in a systematic and structured manner. The potential benefit of Taguchi methodology lies in its ease of use, its emphasis on reducing variability to give more economical products and hence the accessibility to the engineering fraternity for solving real life quality problems. This study applies Taguchi methodology to improve the functional quality of a local made chain gear by a purposed heat treatment process. The hardness of steel is generally a function not of its composition only, but rather of its heat treatment. The study investigates the effects of various heat treatment parameters, including ramp rate of heating, normalizing holding time, normalizing temperature, annealing holding time, annealing temperature, hardening holding time, hardening temperature, quenching media, tempering temperature and tempering holding time upon the hardness, which is a measure of resistance to plastic deformation. Both the analysis of means (ANOM) and Signal to Noise ratio (S/N) have been carried out for determining the optimal condition of the process. A significant improvement of the functional quality characteristic (hardness) by more than 32% was obtained. The Scanning Electron Microscopy technique was used in this study to obtain visual evidence of the quality and continuous improvement of the heat treated samples. (author)

Optimization of an anti-HER2 nanobody expression using the Taguchi method.

Science.gov (United States)

Farasat, Alireza; Rahbarizadeh, Fatemeh; Ahmadvand, Davoud; Yazdian, Fatemeh

2017-09-14

Despite being widely used in immunotherapy of cancer, whole antibodies are limited by several disadvantages. This has led to the advent of novel biomolecules such as nanobodies. Taguchi method is a statistical experimental design to study the effect of multiple variables in biological processes. In an effort to overexpress a recombinant anti-human epidermal growth factor receptor type 2 (HER2) nanobody, we performed a detailed study to find optimal condition of temperature, induction, culture media, vector, and host strain, using Taguchi methodology. A total of 16 various experiments were designed. Total protein of the formulated cultures were assessed by Bradford test and sodium dodecyl sulfate-polyacrylamide gel electrophoresis, followed by size exclusion high performance liquid chromatography to quantify the relative concentration of the nanobody in different expression settings. Western blotting was performed to confirm the expression of the anti-HER2 nanobody. When, individually, optimum parameters determined by Taguchi were applied, including SHuffle strain cultured in LB medium, induced with 0.4 mM isopropyl-β-D-thio-galactoside for 18 h at 24°C, production yield further increased by about 9% (25.4 mg/L), compared to the highest expression setting. Flow cytometry and enzyme-linked immunosorbent assay result indicated improved protein binding in optimized conditions. Overall, our findings provide a basis for further investigations on economical production of recombinant nanobodies to improve production yield and activity.

A Comparison of Central Composite Design and Taguchi Method for Optimizing Fenton Process

Directory of Open Access Journals (Sweden)

Anam Asghar

2014-01-01

Full Text Available In the present study, a comparison of central composite design (CCD and Taguchi method was established for Fenton oxidation. Dyeini, Dye : Fe+2, H2O2 : Fe+2, and pH were identified control variables while COD and decolorization efficiency were selected responses. L9 orthogonal array and face-centered CCD were used for the experimental design. Maximum 99% decolorization and 80% COD removal efficiency were obtained under optimum conditions. R squared values of 0.97 and 0.95 for CCD and Taguchi method, respectively, indicate that both models are statistically significant and are in well agreement with each other. Furthermore, Prob > F less than 0.0500 and ANOVA results indicate the good fitting of selected model with experimental results. Nevertheless, possibility of ranking of input variables in terms of percent contribution to the response value has made Taguchi method a suitable approach for scrutinizing the operating parameters. For present case, pH with percent contribution of 87.62% and 66.2% was ranked as the most contributing and significant factor. This finding of Taguchi method was also verified by 3D contour plots of CCD. Therefore, from this comparative study, it is concluded that Taguchi method with 9 experimental runs and simple interaction plots is a suitable alternative to CCD for several chemical engineering applications.

Taguchi method for partial differential equations with application in tumor growth.

Science.gov (United States)

Ilea, M; Turnea, M; Rotariu, M; Arotăriţei, D; Popescu, Marilena

2014-01-01

The growth of tumors is a highly complex process. To describe this process, mathematical models are needed. A variety of partial differential mathematical models for tumor growth have been developed and studied. Most of those models are based on the reaction-diffusion equations and mass conservation law. A variety of modeling strategies have been developed, each focusing on tumor growth. Systems of time-dependent partial differential equations occur in many branches of applied mathematics. The vast majority of mathematical models in tumor growth are formulated in terms of partial differential equations. We propose a mathematical model for the interactions between these three cancer cell populations. The Taguchi methods are widely used by quality engineering scientists to compare the effects of multiple variables, together with their interactions, with a simple and manageable experimental design. In Taguchi's design of experiments, variation is more interesting to study than the average. First, Taguchi methods are utilized to search for the significant factors and the optimal level combination of parameters. Except the three parameters levels, other factors levels other factors levels would not be considered. Second, cutting parameters namely, cutting speed, depth of cut, and feed rate are designed using the Taguchi method. Finally, the adequacy of the developed mathematical model is proved by ANOVA. According to the results of ANOVA, since the percentage contribution of the combined error is as small. Many mathematical models can be quantitatively characterized by partial differential equations. The use of MATLAB and Taguchi method in this article illustrates the important role of informatics in research in mathematical modeling. The study of tumor growth cells is an exciting and important topic in cancer research and will profit considerably from theoretical input. Interpret these results to be a permanent collaboration between math's and medical oncologists.

Study of Dimple Effect on the Friction Characteristics of a Journal Bearing using Taguchi Method

Science.gov (United States)

Murthy, A. Amar; Raghunandana, Dr.

2018-02-01

The effect of producing dimples using chemically etched techniques or by machining process on the surface of a journal bearing bushing to reduce the friction using Taguchi method is investigated. The data used in the present analysis is based on the results obtained by the series of experiments conducted to study the dimples effect on the Stribeck curve. It is statistically proved that producing dimples on the bushing surface of a journal bearing has significant effect on the friction coefficient when used with light oils. Also it is seen that there is an interaction effect between speeds-load and load-dimples. Hence the interaction effect, which are usually neglected should be considered during actual experiments that significantly contributes in reducing the friction in mixed lubrication regime. The experiments, if were conducted after Taguchi method, then the number of experiments would have been reduced to half of the actual set of experiments that were essentially conducted.

Applying the Taguchi method to river water pollution remediation strategy optimization.

Science.gov (United States)

Yang, Tsung-Ming; Hsu, Nien-Sheng; Chiu, Chih-Chiang; Wang, Hsin-Ju

2014-04-15

Optimization methods usually obtain the travel direction of the solution by substituting the solutions into the objective function. However, if the solution space is too large, this search method may be time consuming. In order to address this problem, this study incorporated the Taguchi method into the solution space search process of the optimization method, and used the characteristics of the Taguchi method to sequence the effects of the variation of decision variables on the system. Based on the level of effect, this study determined the impact factor of decision variables and the optimal solution for the model. The integration of the Taguchi method and the solution optimization method successfully obtained the optimal solution of the optimization problem, while significantly reducing the solution computing time and enhancing the river water quality. The results suggested that the basin with the greatest water quality improvement effectiveness is the Dahan River. Under the optimal strategy of this study, the severe pollution length was reduced from 18 km to 5 km.

Experimental study of optimal self compacting concrete with spent foundry sand as partial replacement for M-sand using Taguchi approach

Directory of Open Access Journals (Sweden)

Nirmala D.B.

2016-06-01

Full Text Available This paper presents the application of Taguchi approach to obtain optimal mix proportion for Self Compacting Concrete (SCC containing spent foundry sand and M-sand. Spent foundry sand is used as a partial replacement for M-sand. The SCC mix has seven control factors namely, Coarse aggregate, M-sand with Spent Foundry sand, Cement, Fly ash, Water, Super plasticizer and Viscosity modifying agent. Modified Nan Su method is used to proportion the initial SCC mix. L18 (21×37 Orthogonal Arrays (OA with the seven control factors having 3 levels is used in Taguchi approach which resulted in 18 SCC mix proportions. All mixtures are extensively tested both in fresh and hardened states to verify whether they meet the practical and technical requirements of SCC. The quality characteristics considering “Nominal the better” situation is applied to the test results to arrive at the optimal SCC mix proportion. Test results indicate that the optimal mix satisfies the requirements of fresh and hardened properties of SCC. The study reveals the feasibility of using spent foundry sand as a partial replacement of M-sand in SCC and also that Taguchi method is a reliable tool to arrive at optimal mix proportion of SCC.

Experimental study of optimal self compacting concrete with spent foundry sand as partial replacement for M-sand using Taguchi approach

Science.gov (United States)

Nirmala, D. B.; Raviraj, S.

2016-06-01

This paper presents the application of Taguchi approach to obtain optimal mix proportion for Self Compacting Concrete (SCC) containing spent foundry sand and M-sand. Spent foundry sand is used as a partial replacement for M-sand. The SCC mix has seven control factors namely, Coarse aggregate, M-sand with Spent Foundry sand, Cement, Fly ash, Water, Super plasticizer and Viscosity modifying agent. Modified Nan Su method is used to proportion the initial SCC mix. L18 (21×37) Orthogonal Arrays (OA) with the seven control factors having 3 levels is used in Taguchi approach which resulted in 18 SCC mix proportions. All mixtures are extensively tested both in fresh and hardened states to verify whether they meet the practical and technical requirements of SCC. The quality characteristics considering "Nominal the better" situation is applied to the test results to arrive at the optimal SCC mix proportion. Test results indicate that the optimal mix satisfies the requirements of fresh and hardened properties of SCC. The study reveals the feasibility of using spent foundry sand as a partial replacement of M-sand in SCC and also that Taguchi method is a reliable tool to arrive at optimal mix proportion of SCC.

An optimization of superhydrophobic polyvinylidene fluoride/zinc oxide materials using Taguchi method

Energy Technology Data Exchange (ETDEWEB)

Mohamed, Adel M.A., E-mail: madel@uqac.ca [Department of Metallurgical and Materials Engineering, Faculty of Petroleum and Mining Engineering, Suez Canal University, Box 43721, Suez (Egypt); Industrial Chair on Atmospheric Icing of Power Network Equipment (CIGELE) and Canada Research Chair on Atmospheric Icing Engineering of Power Networks (INGIVRE) at Université du Québec a Chicoutimi, Québec (Canada); Jafari, Reza; Farzaneh, Masoud [Industrial Chair on Atmospheric Icing of Power Network Equipment (CIGELE) and Canada Research Chair on Atmospheric Icing Engineering of Power Networks (INGIVRE) at Université du Québec a Chicoutimi, Québec (Canada)

2014-01-01

This article is focused on the preparation and characterization of PVDF/ZnO composite materials. The superhydrophobic surface was prepared through spray coating of a mixture of PVDF polymer and ZnO nanoparticles on aluminum substrate. Stearic acid was added to improve the dispersion of ZnO. Taguchi's design of experiment method using MINITAB15 was used to rank several factors that may affect the superhydrophobic properties in order to formulate the optimum conditions. The Taguchi orthogonal array L9 was applied with three level of consideration for each factor. ANOVA were carried out to identify the significant factors that affect the water contact angle. Confirmation tests were performed on the predicted optimum process parameters. The crystallinity and morphology of PVDF–ZnO membranes were determined by Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM). The results of Taguchi method indicate that the ZnO and stearic acid contents were the parameters making significant contribution toward improvement in hydrophobicity of PVDF materials. As the content of ZnO nanoparticles increased, the values of water contact angle increased, ranging from 122° to 159°, while the contact angle hysteresis and sliding angle decreased to 3.5° and 2.5°, respectively. The SEM results show that hierarchical micro-nanostructure of ZnO plays an important role in the formation of the superhydrophobic surface. FTIR results showed that, in the absence or present ZnO nanoparticles, the crystallization of the PVDF occurred predominantly in the β-phase.

Determination of optimum thermal debinding and sintering process parameters using Taguchi Method

CSIR Research Space (South Africa)

Seerane, M

2015-07-01

Full Text Available powder and a wax-based binder. The binder’s backbone component is a low density polyethylene (LDPE). Careful selection of thermal debinding parameters was guided by thermo- gravimetric analysis (TGA) results. The Taguchi method was used to determine... International Light Metals Technology Conference (LMT 2015), Port Elizabeth, South Africa, July 27-29 Determination of Optimum Process for Thermal Debinding and Sintering using Taguchi Method SEERANE Mandya,*, CHIKWANDA Hildab, MACHAKA Ronaldc CSIR...

Optimizing Cu(II) removal from aqueous solution by magnetic nanoparticles immobilized on activated carbon using Taguchi method.

Science.gov (United States)

Ebrahimi Zarandi, Mohammad Javad; Sohrabi, Mahmoud Reza; Khosravi, Morteza; Mansouriieh, Nafiseh; Davallo, Mehran; Khosravan, Azita

2016-01-01

This study synthesized magnetic nanoparticles (Fe(3)O(4)) immobilized on activated carbon (AC) and used them as an effective adsorbent for Cu(II) removal from aqueous solution. The effect of three parameters, including the concentration of Cu(II), dosage of Fe(3)O(4)/AC magnetic nanocomposite and pH on the removal of Cu(II) using Fe(3)O(4)/AC nanocomposite were studied. In order to examine and describe the optimum condition for each of the mentioned parameters, Taguchi's optimization method was used in a batch system and L9 orthogonal array was used for the experimental design. The removal percentage (R%) of Cu(II) and uptake capacity (q) were transformed into an accurate signal-to-noise ratio (S/N) for a 'larger-the-better' response. Taguchi results, which were analyzed based on choosing the best run by examining the S/N, were statistically tested using analysis of variance; the tests showed that all the parameters' main effects were significant within a 95% confidence level. The best conditions for removal of Cu(II) were determined at pH of 7, nanocomposite dosage of 0.1 gL(-1) and initial Cu(II) concentration of 20 mg L(-1) at constant temperature of 25 °C. Generally, the results showed that the simple Taguchi's method is suitable to optimize the Cu(II) removal experiments.

Taguchi experimental design to determine the taste quality characteristic of candied carrot

Science.gov (United States)

Ekawati, Y.; Hapsari, A. A.

2018-03-01

Robust parameter design is used to design product that is robust to noise factors so the product’s performance fits the target and delivers a better quality. In the process of designing and developing the innovative product of candied carrot, robust parameter design is carried out using Taguchi Method. The method is used to determine an optimal quality design. The optimal quality design is based on the process and the composition of product ingredients that are in accordance with consumer needs and requirements. According to the identification of consumer needs from the previous research, quality dimensions that need to be assessed are the taste and texture of the product. The quality dimension assessed in this research is limited to the taste dimension. Organoleptic testing is used for this assessment, specifically hedonic testing that makes assessment based on consumer preferences. The data processing uses mean and signal to noise ratio calculation and optimal level setting to determine the optimal process/composition of product ingredients. The optimal value is analyzed using confirmation experiments to prove that proposed product match consumer needs and requirements. The result of this research is identification of factors that affect the product taste and the optimal quality of product according to Taguchi Method.

Multi-response optimization of process parameters in biogas production from food waste using Taguchi – Grey relational analysis

International Nuclear Information System (INIS)

Deepanraj, B.; Sivasubramanian, V.; Jayaraj, S.

2017-01-01

Highlights: • Influence of process parameters on biogas production was experimentally investigated. • The optimum conditions were determined using Taguchi based Grey relational analysis. • Percentage contribution of chosen parameters were determined using ANOVA. • Empirical relationship between the input and output variables were derived. - Abstract: In the present study, the influence of process parameters and pretreatment on biogas production, volatile solid degradation and COD degradation during anaerobic digestion of food waste were experimentally investigated. Using Taguchi based Grey relational analysis, the optimum condition for anaerobic digestion was found. Taguchi technique was coupled with grey relational analysis to obtain a grey relational grade for evaluating multiple outputs. A L_1_6 orthogonal array was selected and designed for five parameters varied through four levels by applying Taguchi’s design of experiments. The optimum level values of parameters obtained for anaerobic digestion of food waste is solid concentration of 7.5% TS, pH of 7, temperature of 50 °C, C/N ratio of 20.19 and ultrasonication pretreatment. Percentage contribution of input parameters on output was determined using ANOVA. The results showed that pretreatment is the prominent parameter that contributes towards output responses followed by pH, solid concentration, temperature and C/N ratio.

Optimization of PID Parameters Utilizing Variable Weight Grey-Taguchi Method and Particle Swarm Optimization

Science.gov (United States)

Azmi, Nur Iffah Mohamed; Arifin Mat Piah, Kamal; Yusoff, Wan Azhar Wan; Romlay, Fadhlur Rahman Mohd

2018-03-01

Controller that uses PID parameters requires a good tuning method in order to improve the control system performance. Tuning PID control method is divided into two namely the classical methods and the methods of artificial intelligence. Particle swarm optimization algorithm (PSO) is one of the artificial intelligence methods. Previously, researchers had integrated PSO algorithms in the PID parameter tuning process. This research aims to improve the PSO-PID tuning algorithms by integrating the tuning process with the Variable Weight Grey- Taguchi Design of Experiment (DOE) method. This is done by conducting the DOE on the two PSO optimizing parameters: the particle velocity limit and the weight distribution factor. Computer simulations and physical experiments were conducted by using the proposed PSO- PID with the Variable Weight Grey-Taguchi DOE and the classical Ziegler-Nichols methods. They are implemented on the hydraulic positioning system. Simulation results show that the proposed PSO-PID with the Variable Weight Grey-Taguchi DOE has reduced the rise time by 48.13% and settling time by 48.57% compared to the Ziegler-Nichols method. Furthermore, the physical experiment results also show that the proposed PSO-PID with the Variable Weight Grey-Taguchi DOE tuning method responds better than Ziegler-Nichols tuning. In conclusion, this research has improved the PSO-PID parameter by applying the PSO-PID algorithm together with the Variable Weight Grey-Taguchi DOE method as a tuning method in the hydraulic positioning system.

Applying the Taguchi Method to River Water Pollution Remediation Strategy Optimization

Directory of Open Access Journals (Sweden)

Tsung-Ming Yang

2014-04-01

Full Text Available Optimization methods usually obtain the travel direction of the solution by substituting the solutions into the objective function. However, if the solution space is too large, this search method may be time consuming. In order to address this problem, this study incorporated the Taguchi method into the solution space search process of the optimization method, and used the characteristics of the Taguchi method to sequence the effects of the variation of decision variables on the system. Based on the level of effect, this study determined the impact factor of decision variables and the optimal solution for the model. The integration of the Taguchi method and the solution optimization method successfully obtained the optimal solution of the optimization problem, while significantly reducing the solution computing time and enhancing the river water quality. The results suggested that the basin with the greatest water quality improvement effectiveness is the Dahan River. Under the optimal strategy of this study, the severe pollution length was reduced from 18 km to 5 km.

Taguchi Ukichi, un libéral opiniâtre de l’ère Meiji

OpenAIRE

Hurth, Pascal

2014-01-01

Journaliste, historien et homme politique, Taguchi Ukichi s’est fait le chantre du libéralisme à la fin du xixe siècle en défendant le libre-échange et en s’opposant aux propriétaires fonciers. Champion of Liberalism at the end of the 19th century, Taguchi Ukichi (journalist, historian and politician) was a staunch advocate of free trade, strongly opposed to landowners.

Taguchi Approach to Design Optimization for Quality and Cost: An Overview

Science.gov (United States)

Unal, Resit; Dean, Edwin B.

1990-01-01

Calibrations to existing cost of doing business in space indicate that to establish human presence on the Moon and Mars with the Space Exploration Initiative (SEI) will require resources, felt by many, to be more than the national budget can afford. In order for SEI to succeed, we must actually design and build space systems at lower cost this time, even with tremendous increases in quality and performance requirements, such as extremely high reliability. This implies that both government and industry must change the way they do business. Therefore, new philosophy and technology must be employed to design and produce reliable, high quality space systems at low cost. In recognizing the need to reduce cost and improve quality and productivity, Department of Defense (DoD) and National Aeronautics and Space Administration (NASA) have initiated Total Quality Management (TQM). TQM is a revolutionary management strategy in quality assurance and cost reduction. TQM requires complete management commitment, employee involvement, and use of statistical tools. The quality engineering methods of Dr. Taguchi, employing design of experiments (DOE), is one of the most important statistical tools of TQM for designing high quality systems at reduced cost. Taguchi methods provide an efficient and systematic way to optimize designs for performance, quality, and cost. Taguchi methods have been used successfully in Japan and the United States in designing reliable, high quality products at low cost in such areas as automobiles and consumer electronics. However, these methods are just beginning to see application in the aerospace industry. The purpose of this paper is to present an overview of the Taguchi methods for improving quality and reducing cost, describe the current state of applications and its role in identifying cost sensitive design parameters.

Applying the Taguchi method for optimized fabrication of bovine ...

African Journals Online (AJOL)

SERVER

2008-02-19

Feb 19, 2008 ... Nanobiotechnology Research Lab., School of Chemical Engineering, Babol University of Technology, Po.Box: 484, ... nanoparticle by applying the Taguchi method with characterization of the ... of BSA/ethanol and organic solvent adding rate. ... Sodium aside and all other chemicals were purchased from.

Optimization of the pulsed current gas tungsten arc welding (PCGTAW) parameters for corrosion resistance of super duplex stainless steel (UNS S32760) welds using the Taguchi method

International Nuclear Information System (INIS)

Yousefieh, M.; Shamanian, M.; Saatchi, A.

2011-01-01

Research highlights: → Among the four factors and three levels tested, it was concluded that the pulse current had the most significant effect on the pitting potential and the background current had the next most significant effect. The effects of pulse frequency and % on time are less important when compared to the other factors. → The percentage contributions of the pulse current, the background current, % on time, and pulse frequency to the corrosion resistance are 66.28%, 25.97%, 2.71% and 5.04%, respectively. → The optimum conditions within the selected parameter values were found as the second level of pulse current (120 A), second level of background current (60 A), third level of % on time (80%) and third level of pulse frequency (5 Hz). → The confirmation test was carried out at optimum working conditions. Pitting potential was increased to 1.06 V SCE by setting the control factors. Predicted (1.04 V SCE ) and observed (1.06 V SCE ) pitting potential values are close to each other, which are the highest values obtained in the present study. - Abstract: In the present work, a design of experiment (DOE) technique, the Taguchi method, has been used to optimize the pulsed current gas tungsten arc welding (PCGTAW) parameters for the corrosion resistance of super duplex stainless steel (UNS S32760) welds. A L 9 (3 4 ) orthogonal array (OA) of Taguchi design which involves nine experiments for four parameters (pulse current, background current, % on time, pulse frequency) with three levels was used. Corrosion resistance in 3.5%NaCl solution was evaluated by anodic polarization tests at room temperature. Analysis of variance (ANOVA) is performed on the measured data and S/N (signal to noise) ratios. The higher the better response category was selected to obtain optimum conditions. The optimum conditions providing the highest pitting potential were estimated. The optimum conditions were found as the second level of pulse current (120 A), second level of

Combustion characteristics and optimal factors determination with Taguchi method for diesel engines port-injecting hydrogen

International Nuclear Information System (INIS)

Wu, Horng-Wen; Wu, Zhan-Yi

2012-01-01

This study applies the L 9 orthogonal array of the Taguchi method to find out the best hydrogen injection timing, hydrogen-energy-share ratio, and the percentage of exhaust gas circulation (EGR) in a single DI diesel engine. The injection timing is controlled by an electronic control unit (ECU) and the quantity of hydrogen is controlled by hydrogen flow controller. For various engine loads, the authors determine the optimal operating factors for low BSFC (brake specific fuel consumption), NO X , and smoke. Moreover, net heat-release rate involving variable specific heat ratio is computed from the experimental in-cylinder pressure. In-cylinder pressure, net heat-release rate, A/F ratios, COV (coefficient of variations) of IMEP (indicated mean effective pressure), NO X , and smoke using the optimum condition factors are compared with those by original baseline diesel engine. The predictions made using Taguchi's parameter design technique agreed with the confirmation results on 95% confidence interval. At 45% and 60% loads the optimum factor combination compared with the original baseline diesel engine reduces 14.52% for BSFC, 60.5% for NO X and for 42.28% smoke and improves combustion performance such as peak in-cylinder pressure and net heat-release rate. Adding hydrogen and EGR would not generate unstable combustion due to lower COV of IMEP. -- Highlights: ► We use hydrogen injector controlled by ECU and cooled EGR system in a diesel engine. ► Optimal factors by Taguchi method are determined for low BSFC, NO X and smoke. ► The COV of IMEP is lower than 10% so it will not cause the unstable combustion. ► We improve A/F ratio, in-cylinder pressure, and heat-release at optimized engine. ► Decrease is 14.5% for BSFC, 60.5% for NO X , and 42.28% for smoke at optimized engine.

Optimization of a Culture Medium Using the Taguchi Approach for the Production of Microorganisms Active in Odorous Compound Removal

Directory of Open Access Journals (Sweden)

Krzysztof Makowski

2017-07-01

Full Text Available The aim of this work was to develop the composition of a medium for the cultivation of six microbial strains forming a deodorizing consortium: Pseudomonas fluorescens, Enterococcus faecium, Bacillus subtilis, Bacillus megaterium, Leuconostoc mesenteroides and Lactobacillus plantarum. The study focused on the optimization of a highly efficient culture medium composed of readily available components of plant origin to maximize microbial biomass yields, and to create a less expensive alternative to the commercial Tryptic Soy Broth medium (TSB. After preliminary efficiency screening of all tested media components, we selected four substrates for further optimization—soy protein concentrate (SPC, glucose or sucrose, and phosphate salts. The final concentrations of all components were fine-tuned using the Taguchi design for experiments according to an L9 array. Taguchi optimization led to formulation of a culture medium, which was approximately 5 times cheaper than TSB (depending on the components used. Consequently, microbial biomass yields were improved by up to 15-fold (1564%, depending on the strain. The results obtained in the laboratory experiments were then confirmed in pilot- (42 L and industrial- (300 L scale fermentation. Our results show that this method of using a parallel culture microbioreactor with the Taguchi approach can be recommended for optimization of culture media based on substrates of plant origin.

Application of Taguchi method for cutting force optimization in rock ...

Indian Academy of Sciences (India)

Mechanical properties Uniaxial compressive strength. Sawing characteristics .... texture, coarse-grained, grains between 0.08 mm and 4.80 mm, and the coarsest ..... piezoelectric ceramic of Bi0.5Na0.5TiO3 using the Taguchi method. Powder ...

MENENTUKAN KOMBINASI OPTIMAL PARAMETER COFFEE ROASTING UNTUK MENDAPATKAN ROASTED BEAN DENGAN TINGKAT KEMATANGAN MEDIUM ROAST MENGGUNAKAN METODE TAGUCHI

Directory of Open Access Journals (Sweden)

Arya Anantama R

2015-11-01

Full Text Available Penelitian dilakukan dengan Metode Taguchi untuk menentukan kombinasi optimal dari parameter coffeeroasting. Parameter yang diteliti adalah lamanya waktu roasting sebagai faktor A dan volume biji total untuk sekali proses roasting sebagai faktor B.Eksperimen dilakukan dengan tiga level dan tiga nilai untuk masing-masing faktor. Dari hasil Eksperimen Taguchi didapatkan bahwa level faktor yang memberikan pengaruh yang signifikan terhadap roasted bean adalah faktor A pada level 2 dan faktor B pada level 1. Berdasarkan nilai rata-rata roastedbean dan nilai SNR yang dihasilkan, terlihat bahwa faktor A2 (75 menit dan faktor B1 (2 kg menghasilkan nilai rata-rata roasted bean sesuai dengan nilai yang dituju. Eksperimen Konfirmasi dilakukan dengan menggunakan parameter yang dianggap terbaik. Hasil Eksperimen Konfirmasi menunjukkan kombinasi fakor A2 dengan B1 merupakan kombinasi yang optimal untuk mendapatkan roasted bean kualitas premium. Kata Kunci : coffee roasting; kopi, taguchi; roasted bean Abstract The research is done using Taguchi Method to determine optimum combination of coffee roasting parameters. These parameters consist of roasting time as factor A and total volume of every roasting process as factor B.Experiment is conducted within three levels and three values for each factor. Taguchi Method result shows that significant influence toward roasted bean comes from level 2 on factor A and level 1 on factor B. Based on average value of roasted bean and SNR value, factor A2 (75 minutes and factor B1 (2 kg produced average value of roasted bean in accordance to set value. Confirmation experiment is performed with parameters that are most suitable. The result of confirmation experiment shows combination of A2 and B1 as optimum combination to exercise premium quality roasted bean. Keyword : coffee roasting; coffe; taguchi; roasted bean

MADM Technique Integrated with Grey- based Taguchi method for Selection of Alluminium alloys to minimize deburring cost during Drilling

Directory of Open Access Journals (Sweden)

Reddy Sreenivasulu

2015-06-01

Full Text Available Traditionally, burr problems had been considered unavoidable so that most efforts had been made on removal of the burr as a post process. Nowadays, a trend of manufacturing is an integration of the whole production flow from design to end product. Manufacturing problem issues are handled in various stages even from design stage. Therefore, the methods of describing the burr are getting much attention in recent years for the systematic approach to resolve the burr problem at various manufacturing stages. The main objective of this paper is to explore the basic concepts of MADM methods. In this study, five parameters namely speed, feed, drill size, drill geometry such as point angle and clearance angle were identified to influence more on burr formation during drilling. L 18 orthogonal array was selected and experiments were conducted as per Taguchi experimental plan for Aluminium alloy of 2014, 6061, 5035 and 7075 series. The experiment performed on a CNC Machining center with HSS twist drills. The burr size such as height and thickness were measured on exit of each hole. An optimal combination of process parameters was obtained to minimize the burr size via grey relational analysis. The output from grey based- taguchi method fed as input to the MADM. Apart from burr size strength and temperature are also considered as attributes. Finally, the results generated in MADM suggests the suitable alternative of  aluminium alloy, which results in less deburring cost, high strength and high resistance at elevated temperatures.

Experimental Optimization In Polymer BLEND Composite Preparation Based On Mix Level of Taguchi Robust Design

International Nuclear Information System (INIS)

Abdul Aziz Mohamed; Jaafar Abdullah; Dahlan Mohd; Rozaidi Rasid; Megat Harun AlRashid Megat Ahmad; Mahathir Mohamad; Mohd Hamzah Harun

2012-01-01

L 18 orthogonal array in mix level of Taguchi robust design method was carried out to optimize experimental conditions for the preparation of polymer blend composite. Tensile strength and neutron absorption of the composite were the properties of interest. Filler size, filler loading, ball mixing time and dispersion agent concentration were selected as parameters or factors which are expected to affect the composite properties. As a result of Taguchi analysis, filler loading was the most influencing parameter on the tensile strength and neutron absorption. The least influencing was ball-mixing time. The optimal conditions were determined by using mix-level Taguchi robust design method and a polymer composite with tensile strength of 6.33 MPa was successfully prepared. The composite was found to fully absorb thermal neutron flux of 1.04 x 10 5 n/ cm 2 / s with only 2 mm in thickness. In addition, the filler was also characterized by scanning electron microscopy (SEM) and elemental analysis (EDX). (Author)

Optimization of tribological performance of SiC embedded composite coating via Taguchi analysis approach

Science.gov (United States)

Maleque, M. A.; Bello, K. A.; Adebisi, A. A.; Akma, N.

2017-03-01

Tungsten inert gas (TIG) torch is one of the most recently used heat source for surface modification of engineering parts, giving similar results to the more expensive high power laser technique. In this study, ceramic-based embedded composite coating has been produced by precoated silicon carbide (SiC) powders on the AISI 4340 low alloy steel substrate using TIG welding torch process. A design of experiment based on Taguchi approach has been adopted to optimize the TIG cladding process parameters. The L9 orthogonal array and the signal-to-noise was used to study the effect of TIG welding parameters such as arc current, travelling speed, welding voltage and argon flow rate on tribological response behaviour (wear rate, surface roughness and wear track width). The objective of the study was to identify optimal design parameter that significantly minimizes each of the surface quality characteristics. The analysis of the experimental results revealed that the argon flow rate was found to be the most influential factor contributing to the minimum wear and surface roughness of the modified coating surface. On the other hand, the key factor in reducing wear scar is the welding voltage. Finally, a convenient and economical Taguchi approach used in this study was efficient to find out optimal factor settings for obtaining minimum wear rate, wear scar and surface roughness responses in TIG-coated surfaces.

OPTIMASI PARAMETER MESIN LASER CUTTING TERHADAP KEKASARAN DAN LAJU PEMOTONGAN PADA SUS 316L MENGGUNAKAN TAGUCHI GREY RELATIONAL ANALYSIS METHOD

Directory of Open Access Journals (Sweden)

Rakasita R

2016-06-01

Full Text Available Optimasi parameter adalah teknik yang digunakan pada proses manufaktur untuk menghasilkan produk terbaik. Penelitian ini bertujuan untuk mengoptimasi parameter CNC laser cutting, yaitu titik fokus sinar laser, tekanan gas cutting dan cutting speed untuk mengurangi variasi terhadap respon kekasaran dan laju pemotongan pada material SUS 316L. Masing-masing parameter memiliki 3 level dan pada penelitian ini menggunakan matriks orthogonal L9 (34. Metode ANOVA dan Taguchi digunakan untuk menganalisis data hasil percobaan. Optimasi kekasaran minimum permukaan dan laju pemotongan maksimum pada proses laser cutting dilakukan dengan menggunakan Grey relational analysis. Eksperimen konfirmasi digunakan untuk membuktikan hasil optimal yang telah didapatkan dari metode Taguchi Grey relational analysis. Hasil eksperimen menunjukkan bahwa Taguchi Grey relational analysis efektif digunakan untuk mengoptimasi parameter pemesinan pada laser cutting dengan multi respon.   Abstract Parameter optimization is used in manufacturing as an indicator to produce the best manufacturing product. This paper studies an optimization parameters of CNC laser cutting such as focus of laser beam, pressure cutting gases and cutting speed for reducing variation of surface roughness and cutting rate on material SUS 316L. Based on L9(34 orthogonal array parameters, it is analized using ANOVA based on Taguchi method. In order to optimaze the minimum surface roughness and maximum cutting rate in laser cutting process, it is used Grey relational analysis. The confirmation experiments used to validate the optimal results that has done by Taguchi method. The results show that the Taguchi Grey relational analysis is being effective to optimize the machining parameters for laser cutting process with two responses.

Thermochemical hydrolysis of macroalgae Ulva for biorefinery: Taguchi robust design method

Science.gov (United States)

Jiang, Rui; Linzon, Yoav; Vitkin, Edward; Yakhini, Zohar; Chudnovsky, Alexandra; Golberg, Alexander

2016-06-01

Understanding the impact of all process parameters on the efficiency of biomass hydrolysis and on the final yield of products is critical to biorefinery design. Using Taguchi orthogonal arrays experimental design and Partial Least Square Regression, we investigated the impact of change and the comparative significance of thermochemical process temperature, treatment time, %Acid and %Solid load on carbohydrates release from green macroalgae from Ulva genus, a promising biorefinery feedstock. The average density of hydrolysate was determined using a new microelectromechanical optical resonator mass sensor. In addition, using Flux Balance Analysis techniques, we compared the potential fermentation yields of these hydrolysate products using metabolic models of Escherichia coli, Saccharomyces cerevisiae wild type, Saccharomyces cerevisiae RN1016 with xylose isomerase and Clostridium acetobutylicum. We found that %Acid plays the most significant role and treatment time the least significant role in affecting the monosaccharaides released from Ulva biomass. We also found that within the tested range of parameters, hydrolysis with 121 °C, 30 min 2% Acid, 15% Solids could lead to the highest yields of conversion: 54.134-57.500 gr ethanol kg-1 Ulva dry weight by S. cerevisiae RN1016 with xylose isomerase. Our results support optimized marine algae utilization process design and will enable smart energy harvesting by thermochemical hydrolysis.

Thermochemical hydrolysis of macroalgae Ulva for biorefinery: Taguchi robust design method.

Science.gov (United States)

Jiang, Rui; Linzon, Yoav; Vitkin, Edward; Yakhini, Zohar; Chudnovsky, Alexandra; Golberg, Alexander

2016-06-13

Understanding the impact of all process parameters on the efficiency of biomass hydrolysis and on the final yield of products is critical to biorefinery design. Using Taguchi orthogonal arrays experimental design and Partial Least Square Regression, we investigated the impact of change and the comparative significance of thermochemical process temperature, treatment time, %Acid and %Solid load on carbohydrates release from green macroalgae from Ulva genus, a promising biorefinery feedstock. The average density of hydrolysate was determined using a new microelectromechanical optical resonator mass sensor. In addition, using Flux Balance Analysis techniques, we compared the potential fermentation yields of these hydrolysate products using metabolic models of Escherichia coli, Saccharomyces cerevisiae wild type, Saccharomyces cerevisiae RN1016 with xylose isomerase and Clostridium acetobutylicum. We found that %Acid plays the most significant role and treatment time the least significant role in affecting the monosaccharaides released from Ulva biomass. We also found that within the tested range of parameters, hydrolysis with 121 °C, 30 min 2% Acid, 15% Solids could lead to the highest yields of conversion: 54.134-57.500 gr ethanol kg(-1) Ulva dry weight by S. cerevisiae RN1016 with xylose isomerase. Our results support optimized marine algae utilization process design and will enable smart energy harvesting by thermochemical hydrolysis.

Optimization of Squeeze Casting Parameters for 2017 A Wrought Al Alloy Using Taguchi Method

Directory of Open Access Journals (Sweden)

Najib Souissi

2014-04-01

Full Text Available This study applies the Taguchi method to investigate the relationship between the ultimate tensile strength, hardness and process variables in a squeeze casting 2017 A wrought aluminium alloy. The effects of various casting parameters including squeeze pressure, melt temperature and die temperature were studied. Therefore, the objectives of the Taguchi method for the squeeze casting process are to establish the optimal combination of process parameters and to reduce the variation in quality between only a few experiments. The experimental results show that the squeeze pressure significantly affects the microstructure and the mechanical properties of 2017 A Al alloy.

Weibull and lognormal Taguchi analysis using multiple linear regression

International Nuclear Information System (INIS)

Piña-Monarrez, Manuel R.; Ortiz-Yañez, Jesús F.

2015-01-01

The paper provides to reliability practitioners with a method (1) to estimate the robust Weibull family when the Taguchi method (TM) is applied, (2) to estimate the normal operational Weibull family in an accelerated life testing (ALT) analysis to give confidence to the extrapolation and (3) to perform the ANOVA analysis to both the robust and the normal operational Weibull family. On the other hand, because the Weibull distribution neither has the normal additive property nor has a direct relationship with the normal parameters (µ, σ), in this paper, the issues of estimating a Weibull family by using a design of experiment (DOE) are first addressed by using an L_9 (3"4) orthogonal array (OA) in both the TM and in the Weibull proportional hazard model approach (WPHM). Then, by using the Weibull/Gumbel and the lognormal/normal relationships and multiple linear regression, the direct relationships between the Weibull and the lifetime parameters are derived and used to formulate the proposed method. Moreover, since the derived direct relationships always hold, the method is generalized to the lognormal and ALT analysis. Finally, the method’s efficiency is shown through its application to the used OA and to a set of ALT data. - Highlights: • It gives the statistical relations and steps to use the Taguchi Method (TM) to analyze Weibull data. • It gives the steps to determine the unknown Weibull family to both the robust TM setting and the normal ALT level. • It gives a method to determine the expected lifetimes and to perform its ANOVA analysis in TM and ALT analysis. • It gives a method to give confidence to the extrapolation in an ALT analysis by using the Weibull family of the normal level.

Integrasi Taguchi Loss Function dengan Fuzzy Analytical Hierarchy Process dalam Pemilih Pemasok

Directory of Open Access Journals (Sweden)

Ahmad S. Indrapriyatna

2011-01-01

Full Text Available One important issue in the line production is the selection of the company's best supplier. Various criteria should be considered for determining the best supplier. Answering to that challenge, we apply Taguchi loss function- Analytical Hierarchy Process Fuzzy-Linear Programming (Taguchi loss function-Fuzzy AHP to find out the best supplier. Moreover, we also consider multiple criteria, i.e., goods’ completeness, quality, delivery, and quality loss in that analysis. By maximizing the suppliers’ performances based on each criterion and aggregated the suppliers’ performances based on the overall criteria, we selected the best one. Applying this method for selecting the best pressure gauge’s supplier in PT. Coca Cola Bottling Indonesia Central Sumatera (PT. CCBICS, we found out that among three suppliers, the second supplier is the best one.

Factors Affecting Optimal Surface Roughness of AISI 4140 Steel in Turning Operation Using Taguchi Experiment

Science.gov (United States)

Novareza, O.; Sulistiyarini, D. H.; Wiradmoko, R.

2018-02-01

This paper presents the result of using Taguchi method in turning process of medium carbon steel of AISI 4140. The primary concern is to find the optimal surface roughness after turning process. The taguchi method is used to get a combination of factors and factor levels in order to get the optimum surface roughness level. Four important factors with three levels were used in experiment based on Taguchi method. A number of 27 experiments were carried out during the research and analysed using analysis of variance (ANOVA) method. The result of surface finish was determined in Ra type surface roughness. The depth of cut was found to be the most important factors for reducing the surface roughness of AISI 4140 steel. On the contrary, the other important factors i.e. spindle speed and rake side angle of the tool were proven to be less factors that affecting the surface finish. It is interesting to see the effect of coolant composition that gained the second important factors to reduce the roughness. It may need further research to explain this result.

Analysis and design of a Taguchi-Grey based electricity demand predictor for energy management systems

International Nuclear Information System (INIS)

Yao, Albert W.L.; Chi, S.C.

2004-01-01

In order to use electricity efficiently, a demand control management system is one of the effective ways to reduce energy consumption and electric bills. An electricity demand control system is used as a means to monitor and manage the usage of electricity effectively. Moreover, it is a useful tool for avoiding penalties beyond the contracted demand value of electricity with the electric power company. In this project, we developed a Taguchi-Grey based predictor to forecast the demand value of electricity on line. In a Grey prediction, the parameter settings are highly relevant to the accuracy of forecasting. A Taguchi method was employed to optimize the parameter settings for the Grey based electricity demand value predictor. Our experimental results show that the optimal parameter settings of the Grey prediction are α=0.4, five point modeling and three minute sampling time of the data acquisition system. The improved Taguchi-Grey based electricity demand predictor in conjunction with the PC based electricity demand control system is a cost effective and efficient means to manage the usage of electricity

Taguchi Method for Development of Mass Flow Rate Correlation Using Hydrocarbon Refrigerant Mixture in Capillary Tube

OpenAIRE

Sulaimon, Shodiya; Nasution, Henry; Aziz, Azhar Abdul; Abdul-Rahman, Abdul-Halim; Darus, Amer N

2014-01-01

The capillary tube is an important control device used in small vapor compression refrigeration systems such as window air-conditioners, household refrigerators and freezers. This paper develops a non-dimensional correlation based on the test results of the adiabatic capillary tube for the mass flow rate through the tube using a hydrocarbon refrigerant mixture of 89.3% propane and 10.7% butane (HCM). The Taguchi method, a statistical experimental design approach, was employed. This approach e...

Application of Taguchi method for cutting force optimization in rock

Indian Academy of Sciences (India)

In this paper, an optimization study was carried out for the cutting force (Fc) acting on circular diamond sawblades in rock sawing. The peripheral speed, traverse speed, cut depth and flow rate of cooling fluid were considered as operating variables and optimized by using Taguchi approach for the Fc. L16(44) orthogonal ...

Application of Taguchi approach to optimize friction stir welding parameters of polyethylene

Directory of Open Access Journals (Sweden)

Bejaoui S.

2010-06-01

Full Text Available This paper presents experimental and numerical results of butt friction stir welding of high density polyethylene. The FSW designed tool insulates the welded samples and preserves the heat gained from friction thus avoiding the appearance of blisters and splits after welding. The experimental tests, conducted according to combinations of process factors such as rotation speed, welding speed, pin diameter and hold time at beginning welding, were carried out according the Taguchi orthogonal table L27 in randomized way. Temperatures in the joint during the welding operation and flow stresses from the tensile tests of welded samples were measured and variances were analyzed. Identified models were used to simulate, by finite elements, the tensile tests performed on specimens having a weld cordon in their active area. The results show coherence between the numerical predictions and experimental observations in different cases of weld cordon mechanical behaviour.

Identification of strategy parameters for particle swarm optimizer through Taguchi method

Institute of Scientific and Technical Information of China (English)

KHOSLA Arun; KUMAR Shakti; AGGARWAL K.K.

2006-01-01

Particle swarm optimization (PSO), like other evolutionary algorithms is a population-based stochastic algorithm inspired from the metaphor of social interaction in birds, insects, wasps, etc. It has been used for finding promising solutions in complex search space through the interaction of particles in a swarm. It is a well recognized fact that the performance of evolutionary algorithms to a great extent depends on the choice of appropriate strategy/operating parameters like population size,crossover rate, mutation rate, crossover operator, etc. Generally, these parameters are selected through hit and trial process, which is very unsystematic and requires rigorous experimentation. This paper proposes a systematic based on Taguchi method reasoning scheme for rapidly identifying the strategy parameters for the PSO algorithm. The Taguchi method is a robust design approach using fractional factorial design to study a large number of parameters with small number of experiments. Computer simulations have been performed on two benchmark functions-Rosenbrock function and Griewank function-to validate the approach.

An Efficient Taguchi Approach for the Performance Optimization of Health, Safety, Environment and Ergonomics in Generation Companies.

Science.gov (United States)

Azadeh, Ali; Sheikhalishahi, Mohammad

2015-06-01

A unique framework for performance optimization of generation companies (GENCOs) based on health, safety, environment, and ergonomics (HSEE) indicators is presented. To rank this sector of industry, the combination of data envelopment analysis (DEA), principal component analysis (PCA), and Taguchi are used for all branches of GENCOs. These methods are applied in an integrated manner to measure the performance of GENCO. The preferred model between DEA, PCA, and Taguchi is selected based on sensitivity analysis and maximum correlation between rankings. To achieve the stated objectives, noise is introduced into input data. The results show that Taguchi outperforms other methods. Moreover, a comprehensive experiment is carried out to identify the most influential factor for ranking GENCOs. The approach developed in this study could be used for continuous assessment and improvement of GENCO's performance in supplying energy with respect to HSEE factors. The results of such studies would help managers to have better understanding of weak and strong points in terms of HSEE factors.

Hybrid Taguchi DNA Swarm Intelligence for Optimal Inverse Kinematics Redundancy Resolution of Six-DOF Humanoid Robot Arms

Directory of Open Access Journals (Sweden)

Hsu-Chih Huang

2014-01-01

Full Text Available This paper presents a hybrid Taguchi deoxyribonucleic acid (DNA swarm intelligence for solving the inverse kinematics redundancy problem of six degree-of-freedom (DOF humanoid robot arms. The inverse kinematics problem of the multi-DOF humanoid robot arm is redundant and has no general closed-form solutions or analytical solutions. The optimal joint configurations are obtained by minimizing the predefined performance index in DNA algorithm for real-world humanoid robotics application. The Taguchi method is employed to determine the DNA parameters to search for the joint solutions of the six-DOF robot arms more efficiently. This approach circumvents the disadvantage of time-consuming tuning procedure in conventional DNA computing. Simulation results are conducted to illustrate the effectiveness and merit of the proposed methods. This Taguchi-based DNA (TDNA solver outperforms the conventional solvers, such as geometric solver, Jacobian-based solver, genetic algorithm (GA solver and ant, colony optimization (ACO solver.

Application of Taguchi methods to dual mixture ratio propulsion system optimization for SSTO vehicles

Science.gov (United States)

Stanley, Douglas O.; Unal, Resit; Joyner, C. R.

1992-01-01

The application of advanced technologies to future launch vehicle designs would allow the introduction of a rocket-powered, single-stage-to-orbit (SSTO) launch system early in the next century. For a selected SSTO concept, a dual mixture ratio, staged combustion cycle engine that employs a number of innovative technologies was selected as the baseline propulsion system. A series of parametric trade studies are presented to optimize both a dual mixture ratio engine and a single mixture ratio engine of similar design and technology level. The effect of varying lift-off thrust-to-weight ratio, engine mode transition Mach number, mixture ratios, area ratios, and chamber pressure values on overall vehicle weight is examined. The sensitivity of the advanced SSTO vehicle to variations in each of these parameters is presented, taking into account the interaction of each of the parameters with each other. This parametric optimization and sensitivity study employs a Taguchi design method. The Taguchi method is an efficient approach for determining near-optimum design parameters using orthogonal matrices from design of experiments (DOE) theory. Using orthogonal matrices significantly reduces the number of experimental configurations to be studied. The effectiveness and limitations of the Taguchi method for propulsion/vehicle optimization studies as compared to traditional single-variable parametric trade studies is also discussed.

Determining flexor-tendon repair techniques via soft computing

Science.gov (United States)

Johnson, M.; Firoozbakhsh, K.; Moniem, M.; Jamshidi, M.

2001-01-01

An SC-based multi-objective decision-making method for determining the optimal flexor-tendon repair technique from experimental and clinical survey data, and with variable circumstances, was presented. Results were compared with those from the Taguchi method. Using the Taguchi method results in the need to perform ad-hoc decisions when the outcomes for individual objectives are contradictory to a particular preference or circumstance, whereas the SC-based multi-objective technique provides a rigorous straightforward computational process in which changing preferences and importance of differing objectives are easily accommodated. Also, adding more objectives is straightforward and easily accomplished. The use of fuzzy-set representations of information categories provides insight into their performance throughout the range of their universe of discourse. The ability of the technique to provide a "best" medical decision given a particular physician, hospital, patient, situation, and other criteria was also demonstrated.

Statistical analysis of sonochemical synthesis of SAPO-34 nanocrystals using Taguchi experimental design

International Nuclear Information System (INIS)

Askari, Sima; Halladj, Rouein; Nazari, Mahdi

2013-01-01

Highlights: ► Sonochemical synthesis of SAPO-34 nanocrystals. ► Using Taguchi experimental design (L9) for optimizing the experimental procedure. ► The significant effects of all the ultrasonic parameters on the response. - Abstract: SAPO-34 nanocrystals with high crystallinity were synthesized by means of sonochemical method. An L9 orthogonal array of the Taguchi method was implemented to investigate the effects of sonication conditions on the preparation of SAPO-34 with respect to crystallinity of the final product phase. The experimental data establish the favorable phase crystallinity which is improved by increasing the ultrasonic power and the sonication temperature. In the case of ultrasonic irradiation time, however, an initial increases in crystallinity from 5 min to 15 min is followed by a decrease in crystallinity for longer sonication time

Taguchi-generalized regression neural network micro-screening for physical and sensory characteristics of bread.

Science.gov (United States)

Besseris, George J

2018-03-01

Generalized regression neural networks (GRNN) may act as crowdsourcing cognitive agents to screen small, dense and complex datasets. The concurrent screening and optimization of several complex physical and sensory traits of bread is developed using a structured Taguchi-type micro-mining technique. A novel product outlook is offered to industrial operations to cover separate aspects of smart product design, engineering and marketing. Four controlling factors were selected to be modulated directly on a modern production line: 1) the dough weight, 2) the proofing time, 3) the baking time, and 4) the oven zone temperatures. Concentrated experimental recipes were programmed using the Taguchi-type L 9 (3 4 ) OA-sampler to detect potentially non-linear multi-response tendencies. The fused behavior of the master-ranked bread characteristics behavior was smart sampled with GRNN-crowdsourcing and robust analysis. It was found that the combination of the oven zone temperatures to play a highly influential role in all investigated scenarios. Moreover, the oven zone temperatures and the dough weight appeared to be instrumental when attempting to synchronously adjusting all four physical characteristics. The optimal oven-zone temperature setting for concurrent screening-and-optimization was found to be 270-240 °C. The optimized (median) responses for loaf weight, moisture, height, width, color, flavor, crumb structure, softness, and elasticity are: 782 g, 34.8 %, 9.36 cm, 10.41 cm, 6.6, 7.2, 7.6, 7.3, and 7.0, respectively.

Taguchi-generalized regression neural network micro-screening for physical and sensory characteristics of bread

Directory of Open Access Journals (Sweden)

George J. Besseris

2018-03-01

Full Text Available Generalized regression neural networks (GRNN may act as crowdsourcing cognitive agents to screen small, dense and complex datasets. The concurrent screening and optimization of several complex physical and sensory traits of bread is developed using a structured Taguchi-type micro-mining technique. A novel product outlook is offered to industrial operations to cover separate aspects of smart product design, engineering and marketing. Four controlling factors were selected to be modulated directly on a modern production line: 1 the dough weight, 2 the proofing time, 3 the baking time, and 4 the oven zone temperatures. Concentrated experimental recipes were programmed using the Taguchi-type L9(34 OA-sampler to detect potentially non-linear multi-response tendencies. The fused behavior of the master-ranked bread characteristics behavior was smart sampled with GRNN-crowdsourcing and robust analysis. It was found that the combination of the oven zone temperatures to play a highly influential role in all investigated scenarios. Moreover, the oven zone temperatures and the dough weight appeared to be instrumental when attempting to synchronously adjusting all four physical characteristics. The optimal oven-zone temperature setting for concurrent screening-and-optimization was found to be 270–240 °C. The optimized (median responses for loaf weight, moisture, height, width, color, flavor, crumb structure, softness, and elasticity are: 782 g, 34.8 %, 9.36 cm, 10.41 cm, 6.6, 7.2, 7.6, 7.3, and 7.0, respectively. Keywords: Industrial engineering, Food science

Formulation Development and Evaluation of Hybrid Nanocarrier for Cancer Therapy: Taguchi Orthogonal Array Based Design

Directory of Open Access Journals (Sweden)

Rakesh K. Tekade

2013-01-01

Full Text Available Taguchi orthogonal array design is a statistical approach that helps to overcome limitations associated with time consuming full factorial experimental design. In this study, the Taguchi orthogonal array design was applied to establish the optimum conditions for bovine serum albumin (BSA nanocarrier (ANC preparation. Taguchi method with L9 type of robust orthogonal array design was adopted to optimize the experimental conditions. Three key dependent factors namely, BSA concentration (% w/v, volume of BSA solution to total ethanol ratio (v : v, and concentration of diluted ethanolic aqueous solution (% v/v, were studied at three levels 3%, 4%, and 5% w/v; 1 : 0.75, 1 : 0.90, and 1 : 1.05 v/v; 40%, 70%, and 100% v/v, respectively. The ethanolic aqueous solution was used to impart less harsh condition for desolvation and attain controlled nanoparticle formation. The interaction plot studies inferred the ethanolic aqueous solution concentration to be the most influential parameter that affects the particle size of nanoformulation. This method (BSA, 4% w/v; volume of BSA solution to total ethanol ratio, 1 : 0.90 v/v; concentration of diluted ethanolic solution, 70% v/v was able to successfully develop Gemcitabine (G loaded modified albumin nanocarrier (M-ANC-G of size 25.07±2.81 nm (ζ=-23.03±1.015 mV as against to 78.01±4.99 nm (ζ=-24.88±1.37 mV using conventional method albumin nanocarrier (C-ANC-G. Hybrid nanocarriers were generated by chitosan layering (solvent gelation technique of respective ANC to form C-HNC-G and M-HNC-G of sizes 125.29±5.62 nm (ζ=12.01±0.51 mV and 46.28±2.21 nm (ζ=15.05±0.39 mV, respectively. Zeta potential, entrapment, in vitro release, and pH-based stability studies were investigated and influence of formulation parameters are discussed. Cell-line-based cytotoxicity assay (A549 and H460 cells and cell internalization assay (H460 cell line were performed to assess the

Process Parameters Optimization for Friction Stir Welding of Pure Aluminium to Brass (CuZn30 using Taguchi Technique

Directory of Open Access Journals (Sweden)

Elfar O. M. R.

2016-01-01

Full Text Available In this research, the friction stir welding of dissimilar commercial pure aluminium and brass (CuZn30 plates was investigated and the process parameters were optimized using Taguchi L9 orthogonal array. The considered process parameters were the rotational speed, traverse speed and pin offset. The optimum setting was determined with reference to ultimate tensile strength of the joint. The predicted optimum value of ultimate tensile strength was confirmed by experimental run using optimum parameters. Analysis of variance revealed that traverse speed is the most significant factor in controlling the joint tensile strength and pin offset also plays a significant role. In this investigation, the optimum tensile strength is 50% of aluminium base metal. Metallographic examination revealed that intermetallic compounds were formed in the interface of the optimum joint where the tensile failure was observed to take place.

Optimization and modeling of spot welding parameters with simultaneous multiple response consideration using multi objective Taguchi method and RSM

Energy Technology Data Exchange (ETDEWEB)

Muhammad, Nora Siah; Manurung Yupiter HP; Hafidzi, Moham Mad; Abas, Sun Haji Kiyai; Tham, Ghalib; Haru Man, Esa [Universiti Teknologi MARA (UiTM), Selangor (Malaysia)

2012-08-15

This paper presents an alternative method to optimize process parameters of resistance spot welding (RSW) towards weld zone development. The optimization approach attempts to consider simultaneously the multiple quality characteristics, namely weld nugget and heat affected zone (HAZ), using multi objective Taguchi method (MTM). The experimental study was conducted for plate thickness of 1.5mm under different welding current, weld time and hold time. The optimum welding parameters were investigated using the Taguchi method with L9 orthogonal array. The optimum value was analyzed by means of MTM, which involved the calculation of total normalized quality loss (TNQL) and multi signal to noise ratio (MSNR). A significant level of the welding parameters was further obtained by using analysis of variance (ANOVA). Furthermore, the first order model for predicting the weld zone development is derived by using response surface methodology (RSM). Based on the experimental confirmation test, the proposed method can be effectively applied to estimate the size of weld zone, which can be used to enhance and optimized the welding performance in RSW or other application.

Optimization and modeling of spot welding parameters with simultaneous multiple response consideration using multi objective Taguchi method and RSM

International Nuclear Information System (INIS)

Muhammad, Nora Siah; Manurung Yupiter HP; Hafidzi, Moham Mad; Abas, Sun Haji Kiyai; Tham, Ghalib; Haru Man, Esa

2012-01-01

This paper presents an alternative method to optimize process parameters of resistance spot welding (RSW) towards weld zone development. The optimization approach attempts to consider simultaneously the multiple quality characteristics, namely weld nugget and heat affected zone (HAZ), using multi objective Taguchi method (MTM). The experimental study was conducted for plate thickness of 1.5mm under different welding current, weld time and hold time. The optimum welding parameters were investigated using the Taguchi method with L9 orthogonal array. The optimum value was analyzed by means of MTM, which involved the calculation of total normalized quality loss (TNQL) and multi signal to noise ratio (MSNR). A significant level of the welding parameters was further obtained by using analysis of variance (ANOVA). Furthermore, the first order model for predicting the weld zone development is derived by using response surface methodology (RSM). Based on the experimental confirmation test, the proposed method can be effectively applied to estimate the size of weld zone, which can be used to enhance and optimized the welding performance in RSW or other application

Optimization of cooling tower performance analysis using Taguchi method

OpenAIRE

Ramkumar Ramakrishnan; Ragupathy Arumugam

2013-01-01

This study discuss the application of Taguchi method in assessing maximum cooling tower effectiveness for the counter flow cooling tower using expanded wire mesh packing. The experiments were planned based on Taguchi’s L27 orthogonal array .The trail was performed under different inlet conditions of flow rate of water, air and water temperature. Signal-to-noise ratio (S/N) analysis, analysis of variance (ANOVA) and regression were carried out in order to determine the effects of process...

Parametric study on design fractors for the SCS heat exchanger using the Taguchi method

International Nuclear Information System (INIS)

Kim, S. H.; Choi, B. S.; Yoon, J. H.; Jang, M. H.

2002-01-01

Using Taguchi method, design factors, i.e. control factors of the shutdown cooling heat exchanger were investigated to qualify the effect for the time elapsed after the beginning of the system operation. Levels of the control factors were selected from calculations based on the effectiveness-NTU method. From 18 simulations with the KDESCENT program, it was found that the performance of the system is greatly influenced by inlet temperature from the component cooling water at the shell side and mass flow rate of the reactor coolant at the tube side. The Taguchi method makes it possible to select the control factor that has to be controlled and designed with caution. The method gives the effective way to estimate the influence of each control factor to the system performance

Seleção de parâmetros através do método Taguchi para soldagem de revestimento com ligas de níquel pelo processo MIG/MAG Using the Taguchi method to select welding parameters for weld overlay with nickel alloy through the GMAW process

Directory of Open Access Journals (Sweden)

Antonio Rodolfo Paulino Pessoa

2010-12-01

Full Text Available Neste trabalho utilizou-se o método Taguchi (planejamento Robusto de experimentos, para cumprir com um reduzido número de ensaios, dois objetivos: obter a influência dos fatores de controle sobre as variáveis respostas e determinar as condições ideais para aplicação das ligas de níquel nas soldagens de revestimentos através do processo MIG/MAG com transferência metálica por curto-circuito. Foram escolhidos seis fatores de controle com três níveis cada: Tensão de referência, Velocidade de soldagem, Tipo de tecimento, Técnica da tocha, Gás de proteção e o Material de adição. Por sua vez as variáveis respostas escolhidas foram: Diluição (D e Razão entre o reforço e a largura (R/L. As soldagens foram realizadas na posição plana por simples deposição sobre chapas de aço ASTM 516 Gr60 com dimensões de 200 x 50 x 12,7 mm. O uso do tecimento proporcionou cordões com baixos valores da razão R/L e obteve valores bastante baixos de diluição chegando à ordem de 5%. A combinação dos níveis dos fatores de controle apontados como ótimos pelo método Taguchi resultaram em valores para as variáveis repostas consideradas adequadas para a soldagem de revestimento.In this work aim the Taguchi method (Robust design of experiments was chosen to achieve with a limited number of tests two objectives: the first was to the influence of the control factors (welding parameters on quality characteristics (weld bead geometry and the second was to determine optimal conditions for weld overlay with nickel alloy through the GMAW process in a short circuiting transfer mode. Six control factors were employed with three levels each: Reference voltage, Welding speed, Arc oscillation, welding gun orientation (Perpendicular, forehand and backhand, Shielding gas and filler metal. Already the employed quality characteristics were: Percent dilution (D and the ration between reinforcement and bead width (R/L. The weldings were accomplished using

Taguchi optimization: Case study of gold recovery from amalgamation tailing by using froth flotation method

Science.gov (United States)

Sudibyo, Aji, B. B.; Sumardi, S.; Mufakir, F. R.; Junaidi, A.; Nurjaman, F.; Karna, Aziza, Aulia

2017-01-01

Gold amalgamation process was widely used to treat gold ore. This process produces the tailing or amalgamation solid waste, which still contains gold at 8-9 ppm. Froth flotation is one of the promising methods to beneficiate gold from this tailing. However, this process requires optimal conditions which depends on the type of raw material. In this study, Taguchi method was used to optimize the optimum conditions of the froth flotation process. The Taguchi optimization shows that the gold recovery was strongly influenced by the particle size which is the best particle size at 150 mesh followed by the Potassium amyl xanthate concentration, pH and pine oil concentration at 1133.98, 4535.92 and 68.04 gr/ton amalgamation tailing, respectively.

Optimization of Micro-Alloying Elements for Mechanical Properties in Normalized Cast Steel Using Taguchi Technique

Directory of Open Access Journals (Sweden)

Chokkalingam B.

2017-06-01

Full Text Available In this study, Taguchi method is used to find out the effect of micro alloying elements like vanadium, niobium and titanium on the hardness and tensile strength of the normalized cast steel. Based on this method, plan of experiments were made by using orthogonal arrays to acquire the data on hardness and tensile strength. The signal to noise ratio and analysis of variance (ANOVA are used to investigate the effect of these micro alloying elements on these two mechanical properties of the micro alloyed normalized cast steel. The results indicated that in the micro alloyed normalized cast steel both these properties increases when compared to non-micro-alloyed normalized cast steel. The effect of niobium addition was found to be significantly higher to obtain higher hardness and tensile strength when compared to other micro alloying elements. The maximum hardness of 200HV and the maximum tensile strength of 780 N/mm2 were obtained in 0.05%Nb addition micro alloyed normalized cast steel. Micro-alloyed with niobium normalized cast steel have the finest and uniform microstructure and fine pearlite colonies distributed uniformly in the ferrite. The optimum condition to obtain higher hardness and tensile strength were determined. The results were verified with experiments.

Absolute variation of the mechanical characteristics of halloysite reinforced polyurethane nanocomposites complemented by Taguchi and ANOVA approaches

Directory of Open Access Journals (Sweden)

Tayser Sumer Gaaz

Full Text Available The variation of the results of the mechanical properties of halloysite nanotubes (HNTs reinforced thermoplastic polyurethane (TPU at different HNTs loadings was implemented as a tool for analysis. The preparation of HNTs-TPU nanocomposites was performed under four controlled parameters of mixing temperature, mixing speed, mixing time, and HNTs loading at three levels each to satisfy Taguchi method orthogonal array L9 aiming to optimize these parameters for the best measurements of tensile strength, Young’s modulus, and tensile strain (known as responses. The maximum variation of the experimental results for each response was determined and analysed based on the optimized results predicted by Taguchi method and ANOVA. It was found that the maximum absolute variations of the three mentioned responses are 69%, 352%, and 126%, respectively. The analysis has shown that the preparation of the optimized tensile strength requires 1 wt.% HNTs loading (excluding 2 wt.% and 3 wt.%, mixing temperature of 190 °C (excluding 200 °C and 210 °C, and mixing speed of 30 rpm (excluding 40 rpm and 50 rpm. In addition, the analysis has determined that the mixing time at 20 min has no effect on the preparation. The mentioned analysis was fortified by ANOVA, images of FESEM, and DSC results. Seemingly, the agglomeration and distribution of HNTs in the nanocomposite play an important role in the process. The outcome of the analysis could be considered as a very important step towards the reliability of Taguchi method. Keywords: Nanocomposite, Design-of-experiment, Taguchi optimization method, Mechanical properties

Optimization of the Electrocoagulation Process for Removal of Cr(VI Using Taguchi Method

Directory of Open Access Journals (Sweden)

Masoud Asadi Habib

2012-01-01

Full Text Available The aim of this study was to optimize electrocoagulation process for removal of chromium (VI using Taguchi method. An elecrtrocoagulation reactor with six parallel electrodes was used in this study. For this purpose, effects of 7 parameters such as electrode material, electric current, time of reactions, initial pH, initial voltage, initial chromium concentration and rpm of impeller (agitation intensity in two different levels were studied. Model of "OA_32" of Taguchi experimental design method was used. Among the above-mentioned parameters, electric current and electrode material had highest effects and rpm of impeller had the lowest effect on the electrocoagulation performance. According to the obtained results, highest chromium removal (168.33 mg/L observed in the following conditions: electric current=3A, time of reaction=20min, initial pH=4, initial voltage=6v, initial chromium concentration=400mg/L, rpm of impeller=0rpm and iron as electrode material

Optimization of Tape Winding Process Parameters to Enhance the Performance of Solid Rocket Nozzle Throat Back Up Liners using Taguchi's Robust Design Methodology

Science.gov (United States)

Nath, Nayani Kishore

2017-08-01

The throat back up liners is used to protect the nozzle structural members from the severe thermal environment in solid rocket nozzles. The throat back up liners is made with E-glass phenolic prepregs by tape winding process. The objective of this work is to demonstrate the optimization of process parameters of tape winding process to achieve better insulative resistance using Taguchi's robust design methodology. In this method four control factors machine speed, roller pressure, tape tension, tape temperature that were investigated for the tape winding process. The presented work was to study the cogency and acceptability of Taguchi's methodology in manufacturing of throat back up liners. The quality characteristic identified was Back wall temperature. Experiments carried out using L 9 ' (34) orthogonal array with three levels of four different control factors. The test results were analyzed using smaller the better criteria for Signal to Noise ratio in order to optimize the process. The experimental results were analyzed conformed and successfully used to achieve the minimum back wall temperature of the throat back up liners. The enhancement in performance of the throat back up liners was observed by carrying out the oxy-acetylene tests. The influence of back wall temperature on the performance of throat back up liners was verified by ground firing test.

Optimisation Of Cutting Parameters Of Composite Material Laser Cutting Process By Taguchi Method

Science.gov (United States)

Lokesh, S.; Niresh, J.; Neelakrishnan, S.; Rahul, S. P. Deepak

2018-03-01

The aim of this work is to develop a laser cutting process model that can predict the relationship between the process input parameters and resultant surface roughness, kerf width characteristics. The research conduct is based on the Design of Experiment (DOE) analysis. Response Surface Methodology (RSM) is used in this work. It is one of the most practical and most effective techniques to develop a process model. Even though RSM has been used for the optimization of the laser process, this research investigates laser cutting of materials like Composite wood (veneer)to be best circumstances of laser cutting using RSM process. The input parameters evaluated are focal length, power supply and cutting speed, the output responses being kerf width, surface roughness, temperature. To efficiently optimize and customize the kerf width and surface roughness characteristics, a machine laser cutting process model using Taguchi L9 orthogonal methodology was proposed.

Modelling the Cast Component Weight in Hot Chamber Die Casting using Combined Taguchi and Buckingham's π Approach

Science.gov (United States)

Singh, Rupinder

2018-02-01

Hot chamber (HC) die casting process is one of the most widely used commercial processes for the casting of low temperature metals and alloys. This process gives near-net shape product with high dimensional accuracy. However in actual field environment the best settings of input parameters is often conflicting as the shape and size of the casting changes and one have to trade off among various output parameters like hardness, dimensional accuracy, casting defects, microstructure etc. So for online inspection of the cast components properties (without affecting the production line) the weight measurement has been established as one of the cost effective method (as the difference in weight of sound and unsound casting reflects the possible casting defects) in field environment. In the present work at first stage the effect of three input process parameters (namely: pressure at 2nd phase in HC die casting; metal pouring temperature and die opening time) has been studied for optimizing the cast component weight `W' as output parameter in form of macro model based upon Taguchi L9 OA. After this Buckingham's π approach has been applied on Taguchi based macro model for the development of micro model. This study highlights the Taguchi-Buckingham based combined approach as a case study (for conversion of macro model into micro model) by identification of optimum levels of input parameters (based on Taguchi approach) and development of mathematical model (based on Buckingham's π approach). Finally developed mathematical model can be used for predicting W in HC die casting process with more flexibility. The results of study highlights second degree polynomial equation for predicting cast component weight in HC die casting and suggest that pressure at 2nd stage is one of the most contributing factors for controlling the casting defect/weight of casting.

A Comparative Analysis of Taguchi Methodology and Shainin System DoE in the Optimization of Injection Molding Process Parameters

Science.gov (United States)

Khavekar, Rajendra; Vasudevan, Hari, Dr.; Modi, Bhavik

2017-08-01

Two well-known Design of Experiments (DoE) methodologies, such as Taguchi Methods (TM) and Shainin Systems (SS) are compared and analyzed in this study through their implementation in a plastic injection molding unit. Experiments were performed at a perfume bottle cap manufacturing company (made by acrylic material) using TM and SS to find out the root cause of defects and to optimize the process parameters for minimum rejection. Experiments obtained the rejection rate to be 8.57% from 40% (appx.) during trial runs, which is quiet low, representing successful implementation of these DoE methods. The comparison showed that both methodologies gave same set of variables as critical for defect reduction, but with change in their significance order. Also, Taguchi methods require more number of experiments and consume more time compared to the Shainin System. Shainin system is less complicated and is easy to implement, whereas Taguchi methods is statistically more reliable for optimization of process parameters. Finally, experimentations implied that DoE methods are strong and reliable in implementation, as organizations attempt to improve the quality through optimization.

Multi-Responses Optimization Of Edm Sinking Process Of Aisi D2 Tool Steel Using Taguchi Grey–Fuzzy Method

Directory of Open Access Journals (Sweden)

Bobby Oedy Pramoedyo Soepangkat

2014-12-01

Full Text Available Rough machining with Electro Discharge Machining (EDM process gives a large Material Removal Rate (MRR and high Surface Roughness (SR, while finish machining gives low SR and very slow MRR. In this study, Taguchi method coupled with Grey Relational Analysis (GRA and fuzzy logic has been applied for optimization of multiple performance characteristics. The EDM machining parameters (gap voltage, pulse current, on time and duty factor are optimized with considerations of multiple performance characteristics, i.e., MRR and SR. The quality characteristic of MRR is larger-is-better, while the quality characteristic of SR is smaller-is-better. Based on Taguchi method, an L18 mixed-orthogonal array is selected for the experiments. By using the combination of GRA and fuzzy logic, the optimization of complicated multiple performance characteristics was transformed into the optimization of a single response performance index. The most significant machining parameters which affect the multiple performance characteristics were gapvoltage and pulse current. Experimental results have also shown that machining performance characteristics of EDM process can be improved effectively through the combination of Taguchi method, GRA and fuzzy logic.

A feasibility investigation for modeling and optimization of temperature in bone drilling using fuzzy logic and Taguchi optimization methodology.

Science.gov (United States)

Pandey, Rupesh Kumar; Panda, Sudhansu Sekhar

2014-11-01

Drilling of bone is a common procedure in orthopedic surgery to produce hole for screw insertion to fixate the fracture devices and implants. The increase in temperature during such a procedure increases the chances of thermal invasion of bone which can cause thermal osteonecrosis resulting in the increase of healing time or reduction in the stability and strength of the fixation. Therefore, drilling of bone with minimum temperature is a major challenge for orthopedic fracture treatment. This investigation discusses the use of fuzzy logic and Taguchi methodology for predicting and minimizing the temperature produced during bone drilling. The drilling experiments have been conducted on bovine bone using Taguchi's L25 experimental design. A fuzzy model is developed for predicting the temperature during orthopedic drilling as a function of the drilling process parameters (point angle, helix angle, feed rate and cutting speed). Optimum bone drilling process parameters for minimizing the temperature are determined using Taguchi method. The effect of individual cutting parameters on the temperature produced is evaluated using analysis of variance. The fuzzy model using triangular and trapezoidal membership predicts the temperature within a maximum error of ±7%. Taguchi analysis of the obtained results determined the optimal drilling conditions for minimizing the temperature as A3B5C1.The developed system will simplify the tedious task of modeling and determination of the optimal process parameters to minimize the bone drilling temperature. It will reduce the risk of thermal osteonecrosis and can be very effective for the online condition monitoring of the process. © IMechE 2014.

Application of Taguchi Design and Response Surface Methodology for Improving Conversion of Isoeugenol into Vanillin by Resting Cells of Psychrobacter sp. CSW4

OpenAIRE

Ashengroph, Morahem; Nahvi, Iraj; Amini, Jahanshir

2013-01-01

For all industrial processes, modelling, optimisation and control are the keys to enhance productivity and ensure product quality. In the current study, the optimization of process parameters for improving the conversion of isoeugenol to vanillin by Psychrobacter sp. CSW4 was investigated by means of Taguchi approach and Box-Behnken statistical design under resting cell conditions. Taguchi design was employed for screening the significant variables in the bioconversion medium. Sequentially, B...

Investigation of the possibility of copper removal from industrial leachate by raw and calcined phosphogypsum: D-optimal and Taguchi designs

International Nuclear Information System (INIS)

Mesci, Basak; Turan, Nurdan Gamze; Ozgonenel, Okan

2012-01-01

In the present study, the removal of Cu(II) was evaluated by raw and calcined phosphogypsum (PG) as an industrial product. The role of experimental factors on the removal of Cu(II) was examined by using D-optimal and Taguchi designs. The experimental factors and their related levels were selected as initial pH of 3-6-8, adsorbent content of 5, 10, and 25 g L -1 , contact time of 5, 10, and 20 min, and temperature of 20, 40, and 60 C. The results are evaluated by ANOVA test to extract important experimental factors and their levels. The performances of the suggested factorial designs were then compared and regression models that took into account the significant main and interaction effects were suggested. Taguchi design was found as a reliable solution with less number of experiments for adsorption studies with the optimized values. The resultant removal efficiency is calculated as 78.34%. The results revealed that calcined PG is an appropriate adsorbent for Cu(II) removal from leachate of industrial waste. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Comparative Assessment of Cutting Inserts and Optimization during Hard Turning: Taguchi-Based Grey Relational Analysis

Science.gov (United States)

Venkata Subbaiah, K.; Raju, Ch.; Suresh, Ch.

2017-08-01

The present study aims to compare the conventional cutting inserts with wiper cutting inserts during the hard turning of AISI 4340 steel at different workpiece hardness. Type of insert, hardness, cutting speed, feed, and depth of cut are taken as process parameters. Taguchi’s L18 orthogonal array was used to conduct the experimental tests. Parametric analysis carried in order to know the influence of each process parameter on the three important Surface Roughness Characteristics (Ra, Rz, and Rt) and Material Removal Rate. Taguchi based Grey Relational Analysis (GRA) used to optimize the process parameters for individual response and multi-response outputs. Additionally, the analysis of variance (ANOVA) is also applied to identify the most significant factor.

Vertically aligned N-doped CNTs growth using Taguchi experimental design

Energy Technology Data Exchange (ETDEWEB)

Silva, Ricardo M. [CICECO, Department of Materials and Ceramic Engineering, University of Aveiro, 3810-193 Aveiro (Portugal); Fernandes, António J.S. [I3 N, Physics Department, University of Aveiro, 3810-193 Aveiro (Portugal); Ferro, Marta C. [CICECO, Department of Materials and Ceramic Engineering, University of Aveiro, 3810-193 Aveiro (Portugal); Pinna, Nicola [Institut für Chemie, Humboldt-Universität zu Berlin, Brook-Taylor-Str. 2, 12489 Berlin Germany (Germany); Silva, Rui F., E-mail: rsilva@ua.pt [CICECO, Department of Materials and Ceramic Engineering, University of Aveiro, 3810-193 Aveiro (Portugal)

2015-07-30

Highlights: • Taguchi method is employed for the CVD growth of vertically aligned N-doped CNTs. • Optimal growth parameters: NH3 = 90 sccm, T = 825 °C and catalyst pretreatment time = 2 min. • SEM and HRTEM revealed VACNTs with bamboo-like structure of curved graphitic layers. • XPS analysis results indicated 2.00 at.% of N incorporation in the VACNTs. - Abstract: The Taguchi method with a parameter design L{sub 9} orthogonal array was implemented for optimizing the nitrogen incorporation in the structure of vertically aligned N-doped CNTs grown by thermal chemical deposition (TCVD). The maximization of the I{sub D}/I{sub G} ratio of the Raman spectra was selected as the target value. As a result, the optimal deposition configuration was NH{sub 3} = 90 sccm, growth temperature = 825 °C and catalyst pretreatment time of 2 min, the first parameter having the main effect on nitrogen incorporation. A confirmation experiment with these values was performed, ratifying the predicted I{sub D}/I{sub G} ratio of 1.42. Scanning electron microscopy (SEM) characterization revealed a uniform completely vertically aligned array of multiwalled CNTs which individually exhibit a bamboo-like structure, consisting of periodically curved graphitic layers, as depicted by high resolution transmission electron microscopy (HRTEM). The X-ray photoelectron spectroscopy (XPS) results indicated a 2.00 at.% of N incorporation in the CNTs in pyridine-like and graphite-like, as the predominant species.

Supplier Selection for Food Industry: A Combination of Taguchi Loss Function and Fuzzy Analytical Hierarchy Process

Directory of Open Access Journals (Sweden)

Renna Magdalena

2012-09-01

Full Text Available Supplier selection is an important part of supply chain management process by which firms identify, evaluate, and establish contracts with suppliers. Deciding the right supplier can be a complex task. As such, various criteria must be taken into account to choose the best supplier. This study focused on the supply in the packaging division of a food industry in Denpasar-Bali. A combination of Taguchi Loss Function and fuzzy-AHP (Analytical Hierarchy Process Fuzzy Linear Programming was used to determine the best supplier. In this analysis, several suppliers’ criteria were considered, namely quality, delivery, completeness, quality loss and environmental management. By maximizing the suppliers’ performances based on each criterion and aggregating the suppliers’ performances based on the overall criteria, the best supplier was determined. Keywords: supplier selection, taguchi loss function, AHP, fuzzy linear programming,environment

Reaction kinetics, reaction products and compressive strength of ternary activators activated slag designed by Taguchi method

NARCIS (Netherlands)

Yuan, B.; Yu, Q.L.; Brouwers, H.J.H.

2015-01-01

This study investigates the reaction kinetics, the reaction products and the compressive strength of slag activated by ternary activators, namely waterglass, sodium hydroxide and sodium carbonate. Nine mixtures are designed by the Taguchi method considering the factors of sodium carbonate content

Abrasive wear response of TIG-melted TiC composite coating: Taguchi approach

Science.gov (United States)

Maleque, M. A.; Bello, K. A.; Adebisi, A. A.; Dube, A.

2017-03-01

In this study, Taguchi design of experiment approach has been applied to assess wear behaviour of TiC composite coatings deposited on AISI 4340 steel substrates by novel powder preplacement and TIG torch melting processes. To study the abrasive wear behaviour of these coatings against alumina ball at 600° C, a Taguchi’s orthogonal array is used to acquire the wear test data for determining optimal parameters that lead to the minimization of wear rate. Composite coatings are developed based on Taguchi’s L-16 orthogonal array experiment with three process parameters (welding current, welding speed, welding voltage and shielding gas flow rate) at four levels. In this technique, mean response and signal-to-noise ratio are used to evaluate the influence of the TIG process parameters on the wear rate performance of the composite coated surfaces. The results reveal that welding voltage is the most significant control parameter for minimizing wear rate while the current presents the least contribution to the wear rate reduction. The study also shows the best optimal condition has been arrived at A3 (90 A), B4 (2.5 mm/s), C3 (30 V) and D3 (20 L/min), which gives minimum wear rate in TiC embedded coatings. Finally, a confirmatory experiment has been conducted to verify the optimized result and shows that the error between the predicted values and the experimental observation at the optimal condition lies within the limit of 4.7 %. Thus, the validity of the optimum condition for the coatings is established.

Multi objective optimization of performance parameters of a single cylinder diesel engine running with hydrogen using a Taguchi-fuzzy based approach

International Nuclear Information System (INIS)

Bose, Probir Kumar; Deb, Madhujit; Banerjee, Rahul; Majumder, Arindam

2013-01-01

Environmental issues and rapid exhaustion of fossil fuels are the major concerns over the past two decades to search for alternative fuels. Among various alternatives hydrogen is a long-term renewable and least polluting fuel. Its clean burning capability helps to meet the stern emission norms. Full substitution of diesel with hydrogen may not be convenient for the time being but employing of hydrogen in a diesel engine in dual fuel mode is possible. In this experimental investigation a TMI (timed manifold injection) system has been developed using ECU (electronic control unit) with varying injection strategy to deliver hydrogen on to the intake manifold. Through adopting this technique in the existing diesel engine a momentous improvement in performance and combustion parameters has been observed. The study also attempts to explain the application of the fuzzy logic based Taguchi analysis to optimize the performance parameters i.e. BSEC (Brake specific energy consumption), Vol. Eff. (Volumetric efficiency) and BTHE (brake thermal efficiency) for the different hydrogen injection strategies. - Highlights: • A timed manifold injection system has been developed which enhances the BTHE by 31.74% at full load conditions. • Use of hydrogen-diesel dual fuel of BSEC was reduced by a maximum of 68.98% at full load condition compared to diesel. • Τhe Vol. Eff. reduced by 73.14% in dual fuel mode as compared to 77.23% at full load condition with base diesel. • A fuzzy based Taguchi's parameter design technique has been involved in multi objective optimization for prediction. • Predicted optimum combination improved BTHE and Vol. Eff. by 24.04% and 72.87% respectively and reduced BSEC by 59.03%

Optimization of the Electrodeposition Parameters to Improve the Stoichiometry of In2S3 Films for Solar Applications Using the Taguchi Method

Directory of Open Access Journals (Sweden)

Maqsood Ali Mughal

2014-01-01

Full Text Available Properties of electrodeposited semiconductor thin films are dependent upon the electrolyte composition, plating time, and temperature as well as the current density and the nature of the substrate. In this study, the influence of the electrodeposition parameters such as deposition voltage, deposition time, composition of solution, and deposition temperature upon the properties of In2S3 films was analyzed by the Taguchi Method. According to Taguchi analysis, the interaction between deposition voltage and deposition time was significant. Deposition voltage had the largest impact upon the stoichiometry of In2S3 films and deposition temperature had the least impact. The stoichiometric ratios between sulfur and indium (S/In: 3/2 obtained from experiments performed with optimized electrodeposition parameters were in agreement with predicted values from the Taguchi Method. The experiments were carried out according to Taguchi orthogonal array L27 (3^4 design of experiments (DOE. Approximately 600 nm thick In2S3 films were electrodeposited from an organic bath (ethylene glycol-based containing indium chloride (InCl3, sodium chloride (NaCl, and sodium thiosulfate (Na2S2O3·5H2O, the latter used as an additional sulfur source along with elemental sulfur (S. An X-ray diffractometer (XRD, energy dispersive X-ray spectroscopy (EDS unit, and scanning electron microscope (SEM were, respectively, used to analyze the phases, elemental composition, and morphology of the electrodeposited In2S3 films.

Absolute variation of the mechanical characteristics of halloysite reinforced polyurethane nanocomposites complemented by Taguchi and ANOVA approaches

Science.gov (United States)

Gaaz, Tayser Sumer; Sulong, Abu Bakar; Kadhum, Abdul Amir H.; Nassir, Mohamed H.; Al-Amiery, Ahmed A.

The variation of the results of the mechanical properties of halloysite nanotubes (HNTs) reinforced thermoplastic polyurethane (TPU) at different HNTs loadings was implemented as a tool for analysis. The preparation of HNTs-TPU nanocomposites was performed under four controlled parameters of mixing temperature, mixing speed, mixing time, and HNTs loading at three levels each to satisfy Taguchi method orthogonal array L9 aiming to optimize these parameters for the best measurements of tensile strength, Young's modulus, and tensile strain (known as responses). The maximum variation of the experimental results for each response was determined and analysed based on the optimized results predicted by Taguchi method and ANOVA. It was found that the maximum absolute variations of the three mentioned responses are 69%, 352%, and 126%, respectively. The analysis has shown that the preparation of the optimized tensile strength requires 1 wt.% HNTs loading (excluding 2 wt.% and 3 wt.%), mixing temperature of 190 °C (excluding 200 °C and 210 °C), and mixing speed of 30 rpm (excluding 40 rpm and 50 rpm). In addition, the analysis has determined that the mixing time at 20 min has no effect on the preparation. The mentioned analysis was fortified by ANOVA, images of FESEM, and DSC results. Seemingly, the agglomeration and distribution of HNTs in the nanocomposite play an important role in the process. The outcome of the analysis could be considered as a very important step towards the reliability of Taguchi method.

MO-FG-CAMPUS-TeP2-03: Multi-Criteria Optimization Using Taguchi Method for SRS of Multiple Lesions by Single Isocenter

Energy Technology Data Exchange (ETDEWEB)

Alani, S; Honig, N; Schlocker, A; Corn, B [Tel Aviv Medical Center, Tel Aviv (Israel)

2016-06-15

Purpose: This study utilizes the Taguchi Method to evaluate the VMAT planning parameters of single isocenter treatment plans for multiple brain metastases. An optimization model based on Taguchi and utility concept is employed to optimize the planning parameters including: arc arrangement, calculation grid size, calculation model, and beam energy on multiple performance characteristics namely conformity index and dose to normal brain. Methods: Treatment plans, each with 4 metastatic brain lesions were planned using single isocenter technique. The collimator angles were optimized to avoid open areas. In this analysis four planning parameters (a–d) were considered: (a)-Arc arrangements: set1: Gantry 181cw179 couch0; gantry179ccw0, couch315; and gantry0ccw181, couch45. set2: set1 plus additional arc: Gantry 0cw179, couch270. (b)-Energy: 6-MV; 6MV-FFF (c)-Calculation grid size: 1mm; 1.5mm (d)-Calculation models: AAA; Acuros Treatment planning was performed in Varian Eclipse (ver.11.0.30). A suitable orthogonal array was selected (L8) to perform the experiments. After conducting the experiments with the combinations of planning parameters the conformity index (CI) and the normal brain dose S/N ratio for each parameter was calculated. Optimum levels for the multiple response optimizations were determined. Results: We determined that the factors most affecting the conformity index are arc arrangement and beam energy. These tests were also used to evaluate dose to normal brain. In these evaluations, the significant parameters were grid size and calculation model. Using the utility concept we determined the combination of each of the four factors tested in this study that most significantly influence quality of the resulting treatment plans: (a)-arc arrangement-set2, (b)-6MV, (c)-calc.grid 1mm, (d)-Acuros algorithm. Overall, the dominant significant influences on plan quality are (a)-arcarrangement, and (b)-beamenergy. Conclusion: Results were analyzed using ANOVA and

An Approach to Maximize Weld Penetration During TIG Welding of P91 Steel Plates by Utilizing Image Processing and Taguchi Orthogonal Array

Science.gov (United States)

Singh, Akhilesh Kumar; Debnath, Tapas; Dey, Vidyut; Rai, Ram Naresh

2017-10-01

P-91 is modified 9Cr-1Mo steel. Fabricated structures and components of P-91 has a lot of application in power and chemical industry owing to its excellent properties like high temperature stress corrosion resistance, less susceptibility to thermal fatigue at high operating temperatures. The weld quality and surface finish of fabricated structure of P91 is very good when welded by Tungsten Inert Gas welding (TIG). However, the process has its limitation regarding weld penetration. The success of a welding process lies in fabricating with such a combination of parameters that gives maximum weld penetration and minimum weld width. To carry out an investigation on the effect of the autogenous TIG welding parameters on weld penetration and weld width, bead-on-plate welds were carried on P91 plates of thickness 6 mm in accordance to a Taguchi L9 design. Welding current, welding speed and gas flow rate were the three control variables in the investigation. After autogenous (TIG) welding, the dimension of the weld width, weld penetration and weld area were successfully measured by an image analysis technique developed for the study. The maximum error for the measured dimensions of the weld width, penetration and area with the developed image analysis technique was only 2 % compared to the measurements of Leica-Q-Win-V3 software installed in optical microscope. The measurements with the developed software, unlike the measurements under a microscope, required least human intervention. An Analysis of Variance (ANOVA) confirms the significance of the selected parameters. Thereafter, Taguchi's method was successfully used to trade-off between maximum penetration and minimum weld width while keeping the weld area at a minimum.

Optimization of Burr size, Surface Roughness and Circularity Deviation during Drilling of Al 6061 using Taguchi Design Method and Artificial Neural Network

Directory of Open Access Journals (Sweden)

Reddy Sreenivasulu

2015-03-01

Full Text Available This paper presents the influence of cutting parameters like cutting speed, feed rate, drill diameter, point angle and clearance angle on the burr size, surface roughness and circularity deviation of Al 6061 during drilling on CNC vertical machining center. A plan of experiments based on Taguchi technique has been used to acquire the data. An orthogonal array, signal to noise (S/N ratio and analysis of variance (ANOVA are employed to investigate machining characteristics of Al 6061 using HSS twist drill bits of variable tool geometry and maintain constant helix angle of 45 degrees. Confirmation tests have been carried out to predict the optimal setting of process parameters to validate the used approach, obtained the values of 0.2618mm, 0.1821mm, 3.7451µm, 0.0676mm for burr height, burr thickness, surface roughness and circularity deviation respectively. Finally, artificial neural network has been applied to compare the predicted values with the experimental values, good agreement was shown between the predictive model results and the experimental measurements. Normal 0 false false false EN-US X-NONE X-NONE

A comparative study on optimization of machining parameters by turning aerospace materials according to Taguchi method

Directory of Open Access Journals (Sweden)

Altin Abdullah

2017-01-01

Full Text Available The effects of cutting tool coating material and cutting speed on cutting forces and surface roughness were investigated by Taguchi experimental design. Main cutting force, Fz is considered as a criterion. The effects of machining parameters were investigated using Taguchi L18 orthogonal array. Optimal cutting conditions were determined using the signal-to-noise (S/N ratio which is calculated for average surface roughness and cutting force according to the “the smaller is better” approach. Using results of analysis of variance (ANOVA and signal-to-noise (S/N ratio, effects of parameters on both average surface roughness and cutting forces were statistically investigated. It was observed that feed rate and cutting speed had higher effect on cutting force in Hastelloy X, while the feed rate and cutting tool had higher effect on cutting force in Inconel 625. According to average surface roughness the cutting tool and feed rate had higher effect in Hastelloy X and Inconel 625.

An assessment of diagnostic efficiency by Taguchi/DEA methods.

Science.gov (United States)

Taner, Mehmet Tolga; Sezen, Bulent

2009-01-01

The aim of this paper is to propose a new, objective and consistent method for the calculation of the diagnostic efficiency in medical applications. In this study, a hybrid method of Taguchi and DEA is proposed. This method reflects the diversity of inputs and outputs by incorporating the stepwise application of sensitivity, specificity, leveling threshold, and efficiency score. A hypothetical case study is given which involves eight readers of X-ray films in clinical radiology. The selected pairs of sensitivity and specificity yielded two efficient readers. After super efficiency analysis, Reader 6 is found to be the most efficient reader. The paper presents a new, objective and consistent method for the calculation of the diagnostic efficiency in medical applications.

Study of the Parametric Performance of Solid Particle Erosion Wear under the Slurry Pot Test Rig

Directory of Open Access Journals (Sweden)

S.R. More

2017-12-01

Full Text Available Stainless Steel (SS 304 is commonly used material for slurry handling applications like pipelines, valves, pumps and other equipment's. Slurry erosion wear is a common problem in many engineering applications like process industry, thermal and hydraulic power plants and slurry handling equipments. In this paper, experimental investigation of the influence of solid particle size, impact velocity, impact angle and solid concentration parameters in slurry erosion wear behavior of SS 304 using slurry pot test rig. In this study the design of experiments was considered using Taguchi technique. A comparison has been made for the experimental and Taguchi technique results. The erosion wear morphology was studied using micro-graph obtained by scanning electron microscope (SEM analysis. At shallow impact angle 30°, the material removal pattern was observed in the form of micro displacing, scratching and ploughing with plastic deformation of the material. At 60° impact angle, mixed type of micro indentations and pitting action is observed. At normal impact angle 90°, the material removal pattern was observed in form of indentation and rounded lips. It is found that particle velocity was the most influence factor than impact angle, size and solid concentration. From this investigation, it can be concluded that the slurry erosion wear is minimized by controlling the slurry flow velocity which improves the service life of the slurry handling equipments. From the comparison of experimental and Taguchi experimental design results it is found that the percentage deviation was very small with a higher correlation coefficient (r2 0.987 which is agreeable.

Determination of optimal conditions for pressure oxidative leaching of Sarcheshmeh Molybdenite concentrate using Taguchi method

Directory of Open Access Journals (Sweden)

Khoshnevisana A.

2012-01-01

Full Text Available The present research work is based on finding the optimum conditions for pressure oxidative leaching of the molybdenite concentrate to produce technical-grade molybdic oxide (MoO3 with high recovery through further treatment of the filtrate solution. The Taguchi method was used to design and minimize the number of experiments. By using Taguchi orthogonal (L25 array, five parameters (time, temperature, oxygen pressure, pulp density and acid concentration at five levels were selected for 25 experiments. The experiments were designed and carried out in a high-pressure reactor in the presence of nitric acid as solvent and oxidizing agent for the molybdenite concentrate and its ReS2 content. The optimum conditions for pressure leaching of molybdenite were obtained through using Signal to Noise analysis and modified by using Minitab software prediction tool. Furthermore, the optimum condition for an economical pressure leaching of rhenium sulfide (ReS2 was achieved with the same process. Analysis of variance (ANOVA showed that the pulp density is of paramount importance in this process.

Analysis of process parameters in surface grinding using single objective Taguchi and multi-objective grey relational grade

Directory of Open Access Journals (Sweden)

Prashant J. Patil

2016-09-01

Full Text Available Close tolerance and good surface finish are achieved by means of grinding process. This study was carried out for multi-objective optimization of MQL grinding process parameters. Water based Al2O3 and CuO nanofluids of various concentrations are used as lubricant for MQL system. Grinding experiments were carried out on instrumented surface grinding machine. For experimentation purpose Taguchi's method was used. Important process parameters that affect the G ratio and surface finish in MQL grinding are depth of cut, type of lubricant, feed rate, grinding wheel speed, coolant flow rate, and nanoparticle size. Grinding performance was calculated by the measurement G ratio and surface finish. For improvement of grinding process a multi-objective process parameter optimization is performed by use of Taguchi based grey relational analysis. To identify most significant factor of process analysis of variance (ANOVA has been used.

Dye-Sensitized Solar Cells with Optimal Gel Electrolyte Using the Taguchi Design Method

Directory of Open Access Journals (Sweden)

Jenn-Kai Tsai

2013-01-01

Full Text Available The Taguchi method was adopted to determine the optimal gel electrolyte used in dye-sensitized solar cells (DSSCs. Since electrolyte is a very important factor in fabrication of high performance and long-term stability DSSCs, to find the optimal composition of gel electrolyte is desired. In this paper, the common ingredients used in the liquid electrolyte were chosen. The ingredients then mixed with cheap ionic liquids and poly(vinylidenefluoride-co-hexafluoropropylene (PVDF-HFP were added to form colloidal electrolyte (gel. The optimal composition of each materials in the gel electrolyte determined by Taguchi method consists of 0.03 M I2, 0.15 M KI, 0.6 M LiI, 0.5 M 4-tertbutylpyridine (TBP, and 10% PVDF-HFP dissolved in the acetonitrile and 3-methoxypropionitrile (MPN solution with volume ratio of 2 : 1. The short circuit current density of 14.11 mA/cm2, the conversion efficiency (η of 5.52%, and the lifetime of over 110 days were observed for the dye-sensitized solar cell assembled with optimal gel electrolyte. The lifetime increases 10 times when compared with the conventional dye-sensitized solar cell assembled with liquid electrolyte.

Tapped density optimisation for four agricultural wastes - Part II: Performance analysis and Taguchi-Pareto

Directory of Open Access Journals (Sweden)

Ajibade Oluwaseyi Ayodele

2016-01-01

Full Text Available In this attempt, which is a second part of discussions on tapped density optimisation for four agricultural wastes (particles of coconut, periwinkle, palm kernel and egg shells, performance analysis for comparative basis is made. This paper pioneers a study direction in which optimisation of process variables are pursued using Taguchi method integrated with the Pareto 80-20 rule. Negative percentage improvements resulted when the optimal tapped density was compared with the average tapped density. However, the performance analysis between optimal tapped density and the peak tapped density values yielded positive percentage improvements for the four filler particles. The performance analysis results validate the effectiveness of using the Taguchi method in improving the tapped density properties of the filler particles. The application of the Pareto 80-20 rule to the table of parameters and levels produced revised tables of parameters and levels which helped to identify the factor-levels position of each parameter that is economical to optimality. The Pareto 80-20 rule also produced revised S/N response tables which were used to know the relevant S/N ratios that are relevant to optimality.

TAGUCHI METHOD FOR THREE-STAGE ASSEMBLY FLOW SHOP SCHEDULING PROBLEM WITH BLOCKING AND SEQUENCE-DEPENDENT SET UP TIMES

Directory of Open Access Journals (Sweden)

AREF MALEKI-DARONKOLAEI

2013-10-01

Full Text Available This article considers a three-stage assembly flowshop scheduling problem minimizing the weighted sum of mean completion time and makespan with sequence-dependent setup times at the first stage and blocking times between each stage. To tackle such an NP-hard, two meta-heuristic algorithms are presented. The novelty of our approach is to develop a variable neighborhood search algorithm (VNS and a well-known simulated annealing (SA for the problem. Furthermore, to enhance the performance of the (SA, its parameters are optimized by the use of Taguchi method, but to setting parameters of VNS just one parameter has been used without Taguchi. The computational results show that the proposed VNS is better in mean and standard deviation for all sizes of the problem than SA, but on the contrary about CPU Time SA outperforms VNS.

Application of Taguchi Design and Response Surface Methodology for Improving Conversion of Isoeugenol into Vanillin by Resting Cells of Psychrobacter sp. CSW4.

Science.gov (United States)

Ashengroph, Morahem; Nahvi, Iraj; Amini, Jahanshir

2013-01-01

For all industrial processes, modelling, optimisation and control are the keys to enhance productivity and ensure product quality. In the current study, the optimization of process parameters for improving the conversion of isoeugenol to vanillin by Psychrobacter sp. CSW4 was investigated by means of Taguchi approach and Box-Behnken statistical design under resting cell conditions. Taguchi design was employed for screening the significant variables in the bioconversion medium. Sequentially, Box-Behnken design experiments under Response Surface Methodology (RSM) was used for further optimization. Four factors (isoeugenol, NaCl, biomass and tween 80 initial concentrations), which have significant effects on vanillin yield, were selected from ten variables by Taguchi experimental design. With the regression coefficient analysis in the Box-Behnken design, a relationship between vanillin production and four significant variables was obtained, and the optimum levels of the four variables were as follows: initial isoeugenol concentration 6.5 g/L, initial tween 80 concentration 0.89 g/L, initial NaCl concentration 113.2 g/L and initial biomass concentration 6.27 g/L. Under these optimized conditions, the maximum predicted concentration of vanillin was 2.25 g/L. These optimized values of the factors were validated in a triplicate shaking flask study and an average of 2.19 g/L for vanillin, which corresponded to a molar yield 36.3%, after a 24 h bioconversion was obtained. The present work is the first one reporting the application of Taguchi design and Response surface methodology for optimizing bioconversion of isoeugenol into vanillin under resting cell conditions.

Comparative study of coated and uncoated tool inserts with dry machining of EN47 steel using Taguchi L9 optimization technique

Science.gov (United States)

Vasu, M.; Shivananda, Nayaka H.

2018-04-01

EN47 steel samples are machined on a self-centered lathe using Chemical Vapor Deposition of coated TiCN/Al2O3/TiN and uncoated tungsten carbide tool inserts, with nose radius 0.8mm. Results are compared with each other and optimized using statistical tool. Input (cutting) parameters that are considered in this work are feed rate (f), cutting speed (Vc), and depth of cut (ap), the optimization criteria are based on the Taguchi (L9) orthogonal array. ANOVA method is adopted to evaluate the statistical significance and also percentage contribution for each model. Multiple response characteristics namely cutting force (Fz), tool tip temperature (T) and surface roughness (Ra) are evaluated. The results discovered that coated tool insert (TiCN/Al2O3/TiN) exhibits 1.27 and 1.29 times better than the uncoated tool insert for tool tip temperature and surface roughness respectively. A slight increase in cutting force was observed for coated tools.

Optimization of the Adhesion Strength of Arc Ion Plating TiAlN Films by the Taguchi Method

Directory of Open Access Journals (Sweden)

Tong-Yul Cho

2009-06-01

Full Text Available A three-level six-factor (arc power, substrate temperature, pre-treatment bias voltage, working pressure, deposition bias voltage and pretreatment time orthogonal experimental array (L18 to optimize the adhesion strength of arc ion plating (AIP TiAlN films was designed using the Taguchi method. An optimized film process, namely substrate temperature 220 °C, arc power 60 A, negative bias voltage -800 V, nitrogen pressure 10-2 Torr, pretreated voltage -450 V and pretreated time 15 minutes was obtained by the Taguchi program for the purpose of obtaining a larger critical load. The critical load of the optimized TiAlN film (53 N was increased by 43% compared to the film with the highest critical load before optimization. The improvement in the adhesion strength of the films was attributed to the enhancement of hardness and the competitive growth of the (111, (200 and (220 orientations in the film.

Comparative Study Between the Two Experimental Design Approaches Taguchi and Traditional in Presence of Control by Control Interactions

Directory of Open Access Journals (Sweden)

Arias-Nava Elías Heriberto

2015-03-01

Full Text Available Design of experiments plays an important role in the field of creating and innovating process and products directly in manufacturing and improving areas. There are several areas into designs of experiments; robust design is one of them. Robust parameter design is a principle that emphasize in products creation through a correct selection of values called “control” which make a product robust to the variability by the noise introducing by another factors known as “noise” factors. This article aims for a comparative study between two well-known robust design methodologies, making a special emphasis in the control by control interaction effects over optimal operating conditions. The results showed that Taguchi´s crossed arrays are unable to estimate all significant terms in a model. The optimizations result concludes that the Taguchi´s approach is less efficient than the traditional approach in both; maximization and minimization.

Application of Taguchi method to optimization of surface roughness during precise turning of NiTi shape memory alloy

Science.gov (United States)

Kowalczyk, M.

2017-08-01

This paper describes the research results of surface quality research after the NiTi shape memory alloy (Nitinol) precise turning by the tools with edges made of polycrystalline diamonds (PCD). Nitinol, a nearly equiatomic nickel-titanium shape memory alloy, has wide applications in the arms industry, military, medicine and aerospace industry, and industrial robots. Due to their specific properties NiTi alloys are known to be difficult-to-machine materials particularly by using conventional techniques. The research trials were conducted for three independent parameters (vc, f, ap) affecting the surface roughness were analyzed. The choice of parameter configurations were performed by factorial design methods using orthogonal plan type L9, with three control factors, changing on three levels, developed by G. Taguchi. S/N ratio and ANOVA analyses were performed to identify the best of cutting parameters influencing surface roughness.

Optimization of CO2 Laser Cutting Process using Taguchi and Dual Response Surface Methodology

Directory of Open Access Journals (Sweden)

M. Madić

2014-09-01

Full Text Available Selection of optimal cutting parameter settings for obtaining high cut quality in CO2 laser cutting process is of great importance. Among various analytical and experimental optimization methods, the application of Taguchi and response surface methodology is one of most commonly used for laser cutting process optimization. Although the concept of dual response surface methodology for process optimization has been used with success, till date, no experimental study has been reported in the field of laser cutting. In this paper an approach for optimization of CO2 laser cutting process using Taguchi and dual response surface methodology is presented. The goal was to determine the near optimal laser cutting parameter values in order to ensure robust condition for minimization of average surface roughness. To obtain experimental database for development of response surface models, Taguchi’s L25 orthogonal array was implemented for experimental plan. Three cutting parameters, the cutting speed (3, 4, 5, 6, 7 m/min, the laser power (0.7, 0.9, 1.1, 1.3, 1.5 kW, and the assist gas pressure (3, 4, 5, 6, 7 bar, were used in the experiment. To obtain near optimal cutting parameters settings, multi-stage Monte Carlo simulation procedure was performed on the developed response surface models.

Optimization on Turning Parameters of 15-5PH Stainless Steel Using Taguchi Based Grey Approach and Topsis

Directory of Open Access Journals (Sweden)

Palanisamy D.

2016-09-01

Full Text Available The machinability and the process parameter optimization of turning operation for 15-5 Precipitation Hardening (PH stainless steel have been investigated based on the Taguchi based grey approach and Technique for Order Preference by Similarity to Ideal Solution (TOPSIS. An L27 orthogonal array was selected for planning the experiment. Cutting speed, depth of cut and feed rate were considered as input process parameters. Cutting force (Fz and surface roughness (Ra were considered as the performance measures. These performance measures were optimized for the improvement of machinability quality of product. A comparison is made between the multi-criteria decision making tools. Grey Relational Analysis (GRA and TOPSIS are used to confirm and prove the similarity. To determine the influence of process parameters, Analysis of Variance (ANOVA is employed. The end results of experimental investigation proved that the machining performance can be enhanced effectively with the assistance of the proposed approaches.

Optimization of the Machining parameter of LM6 Alminium alloy in CNC Turning using Taguchi method

Science.gov (United States)

Arunkumar, S.; Muthuraman, V.; Baskaralal, V. P. M.

2017-03-01

Due to widespread use of highly automated machine tools in the industry, manufacturing requires reliable models and methods for the prediction of output performance of machining process. In machining of parts, surface quality is one of the most specified customer requirements. In order for manufactures to maximize their gains from utilizing CNC turning, accurate predictive models for surface roughness must be constructed. The prediction of optimum machining conditions for good surface finish plays an important role in process planning. This work deals with the study and development of a surface roughness prediction model for machining LM6 aluminum alloy. Two important tools used in parameter design are Taguchi orthogonal arrays and signal to noise ratio (S/N). Speed, feed, depth of cut and coolant are taken as process parameter at three levels. Taguchi’s parameters design is employed here to perform the experiments based on the various level of the chosen parameter. The statistical analysis results in optimum parameter combination of speed, feed, depth of cut and coolant as the best for obtaining good roughness for the cylindrical components. The result obtained through Taguchi is confirmed with real time experimental work.

Multiple performance characteristics optimization for Al 7075 on electric discharge drilling by Taguchi grey relational theory

Science.gov (United States)

Khanna, Rajesh; Kumar, Anish; Garg, Mohinder Pal; Singh, Ajit; Sharma, Neeraj

2015-12-01

Electric discharge drill machine (EDDM) is a spark erosion process to produce micro-holes in conductive materials. This process is widely used in aerospace, medical, dental and automobile industries. As for the performance evaluation of the electric discharge drilling machine, it is very necessary to study the process parameters of machine tool. In this research paper, a brass rod 2 mm diameter was selected as a tool electrode. The experiments generate output responses such as tool wear rate (TWR). The best parameters such as pulse on-time, pulse off-time and water pressure were studied for best machining characteristics. This investigation presents the use of Taguchi approach for better TWR in drilling of Al-7075. A plan of experiments, based on L27 Taguchi design method, was selected for drilling of material. Analysis of variance (ANOVA) shows the percentage contribution of the control factor in the machining of Al-7075 in EDDM. The optimal combination levels and the significant drilling parameters on TWR were obtained. The optimization results showed that the combination of maximum pulse on-time and minimum pulse off-time gives maximum MRR.

Test techniques for fracture mechanics testing

International Nuclear Information System (INIS)

Schwalbe, K.H.

1980-01-01

Test methods for fracture mechanics tests are described. Two groups of techniques are distinguished: Those for measurement of stable crack growth and those for determination of the loading parameters. (orig.) [de

Multidisciplinary design of a rocket-based combined cycle SSTO launch vehicle using Taguchi methods

Science.gov (United States)

Olds, John R.; Walberg, Gerald D.

1993-01-01

Results are presented from the optimization process of a winged-cone configuration SSTO launch vehicle that employs a rocket-based ejector/ramjet/scramjet/rocket operational mode variable-cycle engine. The Taguchi multidisciplinary parametric-design method was used to evaluate the effects of simultaneously changing a total of eight design variables, rather than changing them one at a time as in conventional tradeoff studies. A combination of design variables was in this way identified which yields very attractive vehicle dry and gross weights.

[Development of an optimized formulation of damask marmalade with low energy level using Taguchi methodology].

Science.gov (United States)

Villarroel, Mario; Castro, Ruth; Junod, Julio

2003-06-01

The goal of this present study was the development of an optimized formula of damask marmalade low in calories applying Taguchi methodology to improve the quality of this product. The selection of this methodology lies on the fact that in real life conditions the result of an experiment frequently depends on the influence of several variables, therefore, one expedite way to solve this problem is utilizing factorial desings. The influence of acid, thickener, sweetener and aroma additives, as well as time of cooking, and possible interactions among some of them, were studied trying to get the best combination of these factors to optimize the sensorial quality of an experimental formulation of dietetic damask marmalade. An orthogonal array L8 (2(7)) was applied in this experience, as well as level average analysis was carried out according Taguchi methodology to determine the suitable working levels of the design factors previously choiced, to achieve a desirable product quality. A sensory trained panel was utilized to analyze the marmalade samples using a composite scoring test with a descriptive acuantitative scale ranging from 1 = Bad, 5 = Good. It was demonstrated that the design factors sugar/aspartame, pectin and damask aroma had a significant effect (p < 0.05) on the sensory quality of the marmalade with 82% of contribution on the response. The optimal combination result to be: citric acid 0.2%; pectin 1%; 30 g sugar/16 mg aspartame/100 g, damask aroma 0.5 ml/100 g, time of cooking 5 minutes. Regarding chemical composition, the most important results turned out to be the decrease in carbohydrate content compaired with traditional marmalade with a reduction of 56% in coloric value and also the amount of dietary fiber greater than similar commercial products. Assays of storage stability were carried out on marmalade samples submitted to different temperatures held in plastic bags of different density. Non percetible sensorial, microbiological and chemical changes

Multiple performance optimization of electrochemical drilling of Inconel 625 using Taguchi based Grey Relational Analysis

Directory of Open Access Journals (Sweden)

N. Manikandan

2017-04-01

Full Text Available In this present investigation, a multi performance characteristics optimization based on Taguchi approach with Grey Relational Analysis (GRA is proposed for Electrochemical Drilling process on Inconel 625 material which is used for marine, nuclear, aerospace applications, especially in corrosive environments. Experimental runs have been planned as per Taguchi’s principle with three input machining variables such as feed rate, flow rate of electrolyte and concentration of electrolyte. Besides the material removal rate and surface roughness, the geometric measures such as overcut, form and orientation tolerance are included as performance measures in this investigation. Outcomes of the analysis show that the feed rate is the predominant variable for the desired performance characteristics. On establishing the desired performance measures and multiple regression models are developed to be used as predictive tools. The confirmation test also conducted to validate the results attained by GRA approach and affirmed that there is considerable improvement with the help of proposed approach.

Prioritizing the effective factors on projectile performance by combination of Analytical Hierarchy Process (AHP method and design of experiment of Taguchi Case study: selected aerospace industries

Directory of Open Access Journals (Sweden)

saberreza bahrami

2016-02-01

Full Text Available The purpose of this research is to prioritize the effective factors in projectile performance. Prioritizing of these factors whit combination of Analytical Hierarchy Process (AHP method and design of experiment Of Taguchi help designers to develop the performance of projectile structure. According to this that since now, researcher tried to increase the performance of projectile whit change in every factors separately, so in this paper tried whit combination of AHP method and design of experiment of Taguchi , analyzed and prioritized all the effective factors in projectile performance simultaneously. For this purpose first by design of experiment Of Taguchi the influence of every these factors on two criteria of range and drift were calculated and then by AHP method these factors were prioritized. By considering of equal weight for both range and drift, the result shows between 11 factors, Firing Angle whit value of 0.3398, Muzzle Velocity whit value of 0.2918 and Burning Time whit value of 0.1257 were the most influenced factors in projectile performance respectively. Propellant Weight and Wind Velocity factors whit value of 0.0104 and 0.00092 were ranked in tenth and eleventh priority respectively.

2-[(Hydroxymethyl)amino]ethanol in water as a preservative: Study of formaldehyde released by Taguchi's method

Science.gov (United States)

Wisessirikul, W.; Loykulnant, S.; Montha, S.; Fhulua, T.; Prapainainar, P.

2016-06-01

This research studied the quantity of free formaldehyde released from 2- [(hydroxymethyl)amino]ethanol (HAE) in DI water and natural rubber latex mixture using high-performance liquid chromatography (HPLC) technique. The quantity of formaldehyde retained in the solution was cross-checked by using titration technique. The investigated factors were the concentration of preservative (HAE), pH, and temperature. Taguchi's method was used to design the experiments. The number of experiments was reduced to 16 experiments from all possible experiments by orthogonal arrays (3 factors and 4 levels in each factor). Minitab program was used as a tool for statistical calculation and for finding the suitable condition for the preservative system. HPLC studies showed that higher temperature and higher concentration of the preservative influence the amount of formaldehyde released. It was found that conditions at which formaldehyde was released in the lowest amount were 1.6%w/v HAE, 4 to 40 °C, and the original pH. Nevertheless, the pH value of NR latex should be more than 10 (the suitable pH value was found to be 13). This preservative can be used to replace current preservative systems and can maintain the quality of latex for long-term storage. Use of the proposed preservative system was also shown to have reduced impact on the toxicity of the environment.

Taguchi Method for Development of Mass Flow Rate Correlation using Hydrocarbon Refrigerant Mixture in Capillary Tube

Directory of Open Access Journals (Sweden)

Shodiya Sulaimon

2014-07-01

Full Text Available The capillary tube is an important control device used in small vapor compression refrigeration systems such as window air-conditioners, household refrigerators and freezers. This paper develops a non-dimensional correlation based on the test results of the adiabatic capillary tube for the mass flow rate through the tube using a hydrocarbon refrigerant mixture of 89.3% propane and 10.7% butane (HCM. The Taguchi method, a statistical experimental design approach, was employed. This approach explores the economic benefit that lies in studies of this nature, where only a small number of experiments are required and yet valid results are obtained. Considering the effects of the capillary tube geometry and the inlet condition of the tube, dimensionless parameters were chosen. The new correlation was also based on the Buckingham Pi theorem. This correlation predicts 86.67% of the present experimental data within a relative deviation of -10% to +10%. The predictions by this correlation were also compared with results in published literature.

Application of Taguchi method for separation of uranium from acetate bearing wastewater using hydroxamic acid based sorbent

International Nuclear Information System (INIS)

Satpati, S.K.; Hareendran, K.; Roy, S.B.; Vaidya, A.; Bankar, V.; Dasgupta, K.; Pal, S.

2016-01-01

Separation and recovery of uranium from effluent of nuclear facility has drawn immense attention in separation science research. The acetic acid based uranium solution effluent generated in uranium metal powder production facility was targeted for the study. Solid state separation technique has been employed using hydroxamic acid based chelating sorbent because of several advantages. In the study, the sorbent performances have been evaluated for its important parameters like isotherm, efficiency and kinetics. The equilibrium adsorption capacity (q e ) and distribution coefficient (K d ) of U(VI) have been evaluated as 3.24 mg/g sorbent and 805 ml/g sorbent respectively. Uranium has been recovered using HCl solution. Uranium removal from the feed was found to be more than 95% and the recovery of uranium was more than 99% from the adsorbed phase. Elution process is faster than sorption process. Taguchi optimization method has been applied for designing experimental study and also to identify the optimum operational conditions for uranium separation process.The developed process is useful for separation and recovery of uranium from acetate bearing wastewater generated in uranium processing facilities

Optimization of Surface Roughness Parameters of Al-6351 Alloy in EDC Process: A Taguchi Coupled Fuzzy Logic Approach

Science.gov (United States)

Kar, Siddhartha; Chakraborty, Sujoy; Dey, Vidyut; Ghosh, Subrata Kumar

2017-10-01

This paper investigates the application of Taguchi method with fuzzy logic for multi objective optimization of roughness parameters in electro discharge coating process of Al-6351 alloy with powder metallurgical compacted SiC/Cu tool. A Taguchi L16 orthogonal array was employed to investigate the roughness parameters by varying tool parameters like composition and compaction load and electro discharge machining parameters like pulse-on time and peak current. Crucial roughness parameters like Centre line average roughness, Average maximum height of the profile and Mean spacing of local peaks of the profile were measured on the coated specimen. The signal to noise ratios were fuzzified to optimize the roughness parameters through a single comprehensive output measure (COM). Best COM obtained with lower values of compaction load, pulse-on time and current and 30:70 (SiC:Cu) composition of tool. Analysis of variance is carried out and a significant COM model is observed with peak current yielding highest contribution followed by pulse-on time, compaction load and composition. The deposited layer is characterised by X-Ray Diffraction analysis which confirmed the presence of tool materials on the work piece surface.

Supplier Selection for Food Industry: A Combination of Taguchi Loss Function and Fuzzy Analytical Hierarchy Process

OpenAIRE

Renna Magdalena

2012-01-01

Supplier selection is an important part of supply chain management process by which firms identify, evaluate, and establish contracts with suppliers. Deciding the right supplier can be a complex task. As such, various criteria must be taken into account to choose the best supplier. This study focused on the supply in the packaging division of a food industry in Denpasar-Bali. A combination of Taguchi Loss Function and fuzzy-AHP (Analytical Hierarchy Process Fuzzy Linear Programming) was used ...

A Taguchi approach on optimal process control parameters for HDPE pipe extrusion process

Science.gov (United States)

Sharma, G. V. S. S.; Rao, R. Umamaheswara; Rao, P. Srinivasa

2017-06-01

High-density polyethylene (HDPE) pipes find versatile applicability for transportation of water, sewage and slurry from one place to another. Hence, these pipes undergo tremendous pressure by the fluid carried. The present work entails the optimization of the withstanding pressure of the HDPE pipes using Taguchi technique. The traditional heuristic methodology stresses on a trial and error approach and relies heavily upon the accumulated experience of the process engineers for determining the optimal process control parameters. This results in setting up of less-than-optimal values. Hence, there arouse a necessity to determine optimal process control parameters for the pipe extrusion process, which can ensure robust pipe quality and process reliability. In the proposed optimization strategy, the design of experiments (DoE) are conducted wherein different control parameter combinations are analyzed by considering multiple setting levels of each control parameter. The concept of signal-to-noise ratio ( S/ N ratio) is applied and ultimately optimum values of process control parameters are obtained as: pushing zone temperature of 166 °C, Dimmer speed at 08 rpm, and Die head temperature to be 192 °C. Confirmation experimental run is also conducted to verify the analysis and research result and values proved to be in synchronization with the main experimental findings and the withstanding pressure showed a significant improvement from 0.60 to 1.004 Mpa.

Response to Taguchi and Noma on "relationship between directionality and orientation in drawings by young children and adults.

Science.gov (United States)

Karev, George B

2006-02-01

When assessing the relationship between direction and orientation in drawings by young children and adults, Taguchi and Noma used a fish-drawing task. However, the fish is not convenient enough as an object for such a task so it is highly preferable to use, instead of a single object, a set of several objects to assess directionality quantitatively. These authors' conclusions do not acknowledge alternative explanations.

Friction stir welding: multi-response optimisation using Taguchi-based GRA

Directory of Open Access Journals (Sweden)

Jitender Kundu

2016-01-01

Full Text Available In present experimental work, friction stir welding of aluminium alloy 5083- H321 is performed for optimisation of process parameters for maximum tensile strength. Taguchi’s L9 orthogonal array has been used for three parameters – tool rotational speed (TRS, traverse speed (TS, and tool tilt angle (TTA with three levels. Multi-response optimisation has been carried out through Taguchi-based grey relational analysis. The grey relational grade has been calculated for all three responses – ultimate tensile strength, percentage elongation, and micro-hardness. Analysis of variance is the tool used for obtaining grey relational grade to find out the significant process parameters. TRS and TS are the two most significant parameters which influence most of the quality characteristics of friction stir welded joint. Validation of predicted values done through confirmation experiments at optimum setting shows a good agreement with experimental values.

Sterility test by radiometric technique

International Nuclear Information System (INIS)

Faruq, Muhammad

1980-01-01

Sterility test of pharmaceuticals can be carried out by the application of pharmacopoeia and radiometric technique. In Indonesia the application of pharmacopoeia technique is carried out through liquid germination for aerobacteria and for fungus and yeast. Radiometric technique is applied to autotrop and heterotrop bacteria. (SMN)

Surface Roughness of Al-5Cu Alloy using a Taguchi-Fuzzy Based Approach

Directory of Open Access Journals (Sweden)

Biswajit Das

2014-07-01

Full Text Available The present paper investigates the application of traditional Taguchi method with fuzzy logic for multi objective optimization of the turning process of Al-5Cu alloy in CNC Lathe machine. The cutting parameters are optimized with considerations of the multiple surface roughness characteristics (Centre line average roughness Ra, Average maximum height of the profile Rz, Maximum height of the profile Rt, Mean spacing of local peaks of the profile Sa . Experimental results are demonstrated to present the effectiveness of this approach. The parameters used in the experiment were cutting speed, depth of cut, feed rate. Other parameters such as tool nose radius, tool material, workpiece length, workpiece diameter, and workpiece material were taken as constant.

Optimization of Blending Parameters and Fiber Size of Kenaf-Bast-Fiber-Reinforced the Thermoplastic Polyurethane Composites by Taguchi Method

Directory of Open Access Journals (Sweden)

Y. A. El-Shekeil

2013-01-01

Full Text Available “Kenaf-fibers- (KF-” reinforced “thermoplastic polyurethane (TPU” composites were prepared by the melt-blending method followed by compression molding. Composite specimens were cut from the sheets that were prepared by compression molding. The criteria of optimization were testing the specimens by tensile test and comparing the ultimate tensile strength. The aim of this study is to optimize processing parameters (e.g., processing temperature, time, and speed and fiber size using the Taguchi approach. These four parameters were investigated in three levels each. The L9 orthogonal array was used based on the number of parameters and levels that has been selected. Furthermore, analysis of variance (ANOVA was used to determine the significance of different parameters. The results showed that the optimum values were 180°C, 50 rpm, 13 min, and 125–300 micron for processing temperature, processing speed, processing time, and fiber size, respectively. Using ANOVA, processing temperature showed the highest significance value followed by fiber size. Processing time and speed did not show any significance on the optimization of TPU/KF.

Experimental Validation for Hot Stamping Process by Using Taguchi Method

Science.gov (United States)

Fawzi Zamri, Mohd; Lim, Syh Kai; Razlan Yusoff, Ahmad

2016-02-01

Due to the demand for reduction in gas emissions, energy saving and producing safer vehicles has driven the development of Ultra High Strength Steel (UHSS) material. To strengthen UHSS material such as boron steel, it needed to undergo a process of hot stamping for heating at certain temperature and time. In this paper, Taguchi method is applied to determine the appropriate parameter of thickness, heating temperature and heating time to achieve optimum strength of boron steel. The experiment is conducted by using flat square shape of hot stamping tool with tensile dog bone as a blank product. Then, the value of tensile strength and hardness is measured as response. The results showed that the lower thickness, higher heating temperature and heating time give the higher strength and hardness for the final product. In conclusion, boron steel blank are able to achieve up to 1200 MPa tensile strength and 650 HV of hardness.

Development of testing techniques for mine fan performance

Institute of Scientific and Technical Information of China (English)

WU Zheng-yan; JIANG Shu-guang; PENG Dan-ren

2006-01-01

Three progressive stages of testing techniques are elaborated, which are entirely manual operating, taking separate instruments testing and computer program controlling. The testing method and principle are detailed based on the testing process for meteorological parameters, air pressure, air quality and rotating velocity. And every testing technique is analyzed. Finally, the technique outlook is viewed. All this plays a leading role in development of the testing techniques.

The optimal parameter design for a welding unit of manufacturing industry by Taguchi method and computer simulation

Energy Technology Data Exchange (ETDEWEB)

Zahraee, S.M.; Chegeni, A.; Toghtamish, A.

2016-07-01

Manufacturing systems include a complicated combination of resources, such as materials, labors, and machines. Hence, when the manufacturing systems are faced with a problem related to the availability of resources it is difficult to identify the root of the problem accurately and effectively. Managers and engineers in companies are trying to achieve a robust production line based on the maximum productivity. The main goal of this paper is to design a robust production line, taking productivity into account in the selected manufacturing industry. This paper presents the application of Taguchi method along with computer simulation for finding an optimum factor setting for three controllable factors, which are a number of welding machines, hydraulic machines, and cutting machines by analyzing the effect of noise factors in a selected manufacturing industry. Based on the final results, the optimal design parameter of welding unit of in the selected manufacturing industry will be obtained when factor A is located at level 2 and B and C are located at level 1. Therefore, maximum productive desirability is achieved when the number of welding machines, hydraulic machines, and cutting machines is equal to 17, 2, and 1, respectively. This paper has a significant role in designing a robust production line by considering the lowest cost and timely manner based on the Taguchi method. (Author)

The optimal parameter design for a welding unit of manufacturing industry by Taguchi method and computer simulation

Directory of Open Access Journals (Sweden)

Seyed Mojib Zahraee

2016-05-01

Full Text Available Purpose: Manufacturing systems include a complicated combination of resources, such as materials, labors, and machines. Hence, when the manufacturing systems are faced with a problem related to the availability of resources it is difficult to identify the root of the problem accurately and effectively. Managers and engineers in companies are trying to achieve a robust production line based on the maximum productivity. The main goal of this paper is to design a robust production line, taking productivity into account in the selected manufacturing industry. Design/methodology/approach: This paper presents the application of Taguchi method along with computer simulation for finding an optimum factor setting for three controllable factors, which are a number of welding machines, hydraulic machines, and cutting machines by analyzing the effect of noise factors in a selected manufacturing industry. Findings and Originality/value: Based on the final results, the optimal design parameter of welding unit of in the selected manufacturing industry will be obtained when factor A is located at level 2 and B and C are located at level 1. Therefore, maximum productive desirability is achieved when the number of welding machines, hydraulic machines, and cutting machines is equal to 17, 2, and 1, respectively. This paper has a significant role in designing a robust production line by considering the lowest cost and timely manner based on the Taguchi method.

Mechanical and thermal properties optimization of a synthetic agglomerate by using the Taguchi Method Optimización de propiedades mecánicas y térmicas de un aglomerado sintético por el Método de Taguchi

Directory of Open Access Journals (Sweden)

C. M. Bedoya–Hincapié

2009-12-01

Full Text Available In this work, the experimental design of Taguchi model was applied in order to obtain the most appropriate parameters to elaborate an agglomerate material which presents a good mechanical and thermal behavior. The raw materials used were rice husk, common clay, sand and aloe gel. The importance of the development of the synthetic agglomerates is in the use of agricultural wastes to give them an useful employment when replacing materials of great demand. The experimental combinations were done varying the control factors values: rice husk percentage (R, temperature (T and thermal treatment time(t. Via to the optimization properties according Taguchi’s Methodology, the elasticity modulus, the absorbed energy in the impact, break maximum module and initial decomposition temperature to each experimental combination were selected. The Qualitek-4 software was used below the biggest the better quality characteristic. The optimum parameters obtained to each control level were: R = 15%, T = 120oC and t = 3 h. These results were confirmed with a new experiment, where similar properties to the wood species were obtained. The developing of this will be useful as substitute of the wood and could improve the environment impact due residual materials.En este trabajo se aplicó el modelo de Diseño Experimental de Taguchi para la optimización de las propiedades mecánicas y térmicas de un material compuesto aglomerado y obtener los parámetros más adecuados para su elaboración. La importancia del desarrollo de los aglomerados sintéticos está en el uso de desechos agrícolas para darle un empleo útil al suplir materiales de gran demanda. Se utilizaron la cáscara de arroz, arcilla, arena y gel de aloe como materias primas. Con la variación de los valores de los factores de control: porcentaje de cáscara de arroz (R, temperatura (T y tiempo de tratamiento térmico (t, se realizaron las diferentes combinaciones experimentales. Para la optimización de

Application of Taguchi optimization on the cassava starch wastewater electrocoagulation using batch recycle method

Science.gov (United States)

Sudibyo, Hermida, L.; Suwardi

2017-11-01

Tapioca waste water is very difficult to treat; hence many tapioca factories could not treat it well. One of method which able to overcome this problem is electrodeposition. This process has high performance when it conducted using batch recycle process and use aluminum bipolar electrode. However, the optimum operation conditions are having a significant effect in the tapioca wastewater treatment using bath recycle process. In this research, The Taguchi method was successfully applied to know the optimum condition and the interaction between parameters in electrocoagulation process. The results show that current density, conductivity, electrode distance, and pH have a significant effect on the turbidity removal of cassava starch waste water.

Applying the Taguchi Method for Investigating the Phase-Locked Loop Dynamics Affected by Hybrid Storage System Parameters

Directory of Open Access Journals (Sweden)

Mostafa Ahmadzadeh

2018-01-01

Full Text Available Storage systems play an important role in performance of micro-grids. Storage systems may decrease fluctuations caused by periodic and unpredictable nature of distributed generation resource. Some micro-grids are connected to the network via a grid-interface converter. The phase-locked loop (PLL is a commonly technique for the grid synchronization of network-connected converters. Various parameters affect the stability of PLL (including the network-side and microgrid-side parameters. The effect of the micro-grid-side parameters on the stability of the PLL has not been studied so far. In this paper, the stability of PLL influenced by microgrid-side parameters has been evaluated after a detailed analytical modeling of micro-grid components (including the production power fluctuations, energy storage system, microgrid-side loads, controller parameters etc.. This paper proposes two new stability analysis criteria for PLL affected by micro-grid and hybrid storage system parameters. Using proposed criteria for stability of PLL, optimized rate of micro-grid and hybrid storage system parameters are obtained using statistical methods (Taguchi approach. Finally, behavior of PLL affected by hybrid storage system is investigated. The simulation results and eigenvalues analysis confirm the theoretical analysis and proposed criteria.

Report on COTECH test procedure and characterization techniques

DEFF Research Database (Denmark)

Islam, Mohammad Aminul

that need to be attained for successful characterization of the planned demonstrators and it deals with the material characterization and prototype testing for the COTECH demonstrators. The summary of this report includes:  General description of COTECH industrial demonstrators  COTECH materials...... and material characterization techniques  Characterization techniques of the COTECH demonstrators  Functionality and lifecycle testing of the COTECH demonstrators Besides the general introduction and conclusion each section of the report is dedicated to the characterization techniques and test procedure.......Characterization techniques and test procedure requirements for innovative self-ligating dental brackets (EO) Section 5.Characterization techniques and test procedure requirements for smart diagnostic chips comprising a microfluidic channel system (GBO) Section 6.Characterization techniques and test procedure...

Nitric acid treated multi-walled carbon nanotubes optimized by Taguchi method

Energy Technology Data Exchange (ETDEWEB)

Shamsuddin, Shahidah Arina; Hashim, Uda; Halim, Nur Hamidah Abdul [Institute of Nano Electronic Engineering, Universiti Malaysia Perlis, 01000, Kangar, Perlis (Malaysia); Derman, Mohd Nazree, E-mail: nazree@unimap.edu.my; Tahir, Muhammad Faheem Mohd [Centre of Excellence Geopolymer & Green Technology (CEGeoGTech), School of Material Engineering, Universiti Malaysia Perlis, 01000, Kangar, Perlis (Malaysia); Kashif, Muhammad [Faculty of Engineering, Universiti Malaysia Sarawak, 94300, Kota Samarahan, Sarawak (Malaysia); Adam, Tijjani [Faculty of Engineering Technology, Universiti Malaysia Perlis, 02100, Padang Besar, Perlis (Malaysia)

2016-07-19

Electron transfer rate (ETR) of CNTs can be enhanced by increasing the amounts of COOH groups to their wall and opened tips. With the aim to achieve the highest production amount of COOH, Taguchi robust design has been used for the first time to optimize the surface modification of MWCNTs by nitric acid oxidation. Three main oxidation parameters which are concentration of acid, treatment temperature and treatment time have been selected as the control factors that will be optimized. The amounts of COOH produced are measured by using FTIR spectroscopy through the absorbance intensity. From the analysis, we found that acid concentration and treatment time had the most important influence on the production of COOH. Meanwhile, the treatment temperature will only give intermediate effect. The optimum amount of COOH can be achieved with the treatment by 8.0 M concentration of nitric acid at 120 °C for 2 hour.

Nitric acid treated multi-walled carbon nanotubes optimized by Taguchi method

International Nuclear Information System (INIS)

Shamsuddin, Shahidah Arina; Hashim, Uda; Halim, Nur Hamidah Abdul; Derman, Mohd Nazree; Tahir, Muhammad Faheem Mohd; Kashif, Muhammad; Adam, Tijjani

2016-01-01

Electron transfer rate (ETR) of CNTs can be enhanced by increasing the amounts of COOH groups to their wall and opened tips. With the aim to achieve the highest production amount of COOH, Taguchi robust design has been used for the first time to optimize the surface modification of MWCNTs by nitric acid oxidation. Three main oxidation parameters which are concentration of acid, treatment temperature and treatment time have been selected as the control factors that will be optimized. The amounts of COOH produced are measured by using FTIR spectroscopy through the absorbance intensity. From the analysis, we found that acid concentration and treatment time had the most important influence on the production of COOH. Meanwhile, the treatment temperature will only give intermediate effect. The optimum amount of COOH can be achieved with the treatment by 8.0 M concentration of nitric acid at 120 °C for 2 hour.

Parametric optimization of CNC end milling using entropy ...

African Journals Online (AJOL)

Parametric optimization of CNC end milling using entropy measurement technique combined with grey-Taguchi method. ... International Journal of Engineering, Science and Technology ... Keywords: CNC end milling, surface finish, material removal rate (MRR), entropy measurement technique, Taguchi method ...

Método Taguchi para optimizar marcadores RAPD-PCR y determinar diversidad genética: un modelo, la tortuga cabezona Caretta caretta (Testudines: Cheloniidae

Directory of Open Access Journals (Sweden)

Julio Martínez-Ortega

2013-06-01

Full Text Available Implementation of Taguchi method to optimize RAPD-PCR Markers for determining the genetic diversity: an example the loggerhead turtle, Caretta caretta (Testudines:Cheloniidae. DNA was isolated from Caretta caretta two zone of the Colombian Caribbean (Don Diego N=5 and Rosario Islands N=3 and quantified it. Was applied a Taguchi orthogonal matriz of four variables to standardize RAPD-PCR reaction. The data were analyzed with the program PopGen. The conditions were standardized to 7.85 ng/ml of DNA, 3.5 mM MgCl2, 200 mM dNTP's, 0.5 mM oligonucleotide and one unit of Taq DNA polymerase in a final reaction volume of 20 ml. Thermocycling conditions initiated at 94°C for 5 min, followed by 40 cycles of: 94°C for 40 s, 37°C for 40 s and 72°C for 90 s. The markers were recorded in a binary matrix of presence (1 and absence (0, and as a model example of genetic diversity was determined using the Shannon index (H '= 0.44 + / -0.27 individuals and Don Diego H '= 0.25 + / -0.32 for Isla del Rosario, the average rate of genetic structure (Gst=0.27 and the effective migration rate (Nm=1.28. Methodology was standardized using Taguchi method that produces bands of light, legible and reproducible that can be used as a reliable alternative for studies of genetic diversity in the loggerhead turtle and other species, and further, integrate them into the curriculum of molecular biology and/or biochemistry for undergraduate and graduate students.

Simultaneous improvement of surface quality and productivity using grey relational analysis based Taguchi design for turning couple (AISI D3 steel/ mixed ceramic tool (Al2O3 + TiC

Directory of Open Access Journals (Sweden)

Oussama Zerti

2017-07-01

Full Text Available Current optimization strategies are based on the increase the productivity and the quality with lower cost in short time. Grey relational analysis “GRA” based on Taguchi design was proposed in this paper for simultaneous improvement of surface quality and productivity. The turning trials based on mixed Taguchi L18 factorial plan were conducted under dry cutting conditions for the machining couple: AISI D3 steel/mixed ceramic inserts (CC650. The machining parameters taken into account during this study are as follow: major cutting edge angle (χr, cutting insert nose radius (r, cutting speed (Vc, feed rate (f, and depth of cut (ap. Significant effects of machining parameters and their interactions were evaluated by the analysis of variance. Through this analysis, it have been found clearly that feed rate and cutting insert nose radius had a big significant effects on surface quality while depth of cut, feed rate followed by cutting speed had a major effect on productivity. The mathematical relationship between the machining parameters and the performance characteristics was formulated by using a linear regression model with interactions. Optimal levels of parametric combination for achieving the higher surface quality with maximum productivity were selected by grey relational analysis which is based on the high value of grey relational grade. Confirmation experiments were carried out to prove the powerful improvement of experimental results and to validate the effectiveness of the multi-optimization technique applied in this paper.

Abatement of Cr (Ⅵ) from wastewater using a new adsorbent, cantaloupe peel: Taguchi L{sub 16} orthogonal array optimization

Energy Technology Data Exchange (ETDEWEB)

Ramavandi, Bahman [Bushehr University of Medical Sciences, Bushehr (Iran, Islamic Republic of); Asgari, Ghorban; Faradmal, Javad [Hamadan University of Medical Sciences, Hamadan (Iran, Islamic Republic of); Sahebi, Soleyman [University of Technology, Sydney (UTS), Sydney (Australia); Roshani, Babak [DelcoWater, Saskatoon (Canada)

2014-12-15

Taguchi orthogonal design was applied for multivariate optimization of Cr (Ⅵ) abatement by cantaloupe peel powder (CPP), as a novel adsorbent, from industrial wastewater in a batch mode. Effective factors in the adsorption process, such as temperature, CPP dose, Cr (Ⅵ) concentration, wastewater pH, and contact time, were considered using an L{sub 16} orthogonal array design. The best conditions for adsorbing of Cr (Ⅵ) were determined by the Taguchi method and desirability approach as pH of 2, chromium concentration of 100mg/L, contact time of 5min, CPP dosage of 0.5 g/L, and wastewater temperature of 25 .deg. C. Analysis of variance results indicated that the pH was the most important variable influencing the chromium removal percentage, and its contribution value was obtained 45.01%. The Langmuir model proved best fit for the experimental data and maximum adsorption capacity of Cr (Ⅵ) onto CPP was obtained 166.25mg/g. The final part of the study includes an examination of the CPP through an analysis of the removal of chromium from real industrial wastewater. It can be concluded that the CPP presents a promising and efficient alternative for eliminating of Cr (Ⅵ) from industrial wastewaters.

Application of the Taguchi Method for Optimizing the Process Parameters of Producing Lightweight Aggregates by Incorporating Tile Grinding Sludge with Reservoir Sediments.

Science.gov (United States)

Chen, How-Ji; Chang, Sheng-Nan; Tang, Chao-Wei

2017-11-10

This study aimed to apply the Taguchi optimization technique to determine the process conditions for producing synthetic lightweight aggregate (LWA) by incorporating tile grinding sludge powder with reservoir sediments. An orthogonal array L 16 (4⁵) was adopted, which consisted of five controllable four-level factors (i.e., sludge content, preheat temperature, preheat time, sintering temperature, and sintering time). Moreover, the analysis of variance method was used to explore the effects of the experimental factors on the particle density, water absorption, bloating ratio, and loss on ignition of the produced LWA. Overall, the produced aggregates had particle densities ranging from 0.43 to 2.1 g/cm³ and water absorption ranging from 0.6% to 13.4%. These values are comparable to the requirements for ordinary and high-performance LWAs. The results indicated that it is considerably feasible to produce high-performance LWA by incorporating tile grinding sludge with reservoir sediments.

Optimization of operating parameters of ground source heat pump system for space heating and cooling by Taguchi method and utility concept

International Nuclear Information System (INIS)

Sivasakthivel, T.; Murugesan, K.; Thomas, H.R.

2014-01-01

Highlights: • Ground Source Heat Pump (GSHP) technology is suitable for both heating and cooling. • Important parameters that affect the GSHP performance has been listed. • Parameters of GSHP system has been optimized for heating and cooling mode. • Taguchi technique and utility concept are developed for GSHP optimization. - Abstract: Use of ground source energy for space heating applications through Ground Source Heat pump (GSHP) has been established as an efficient thermodynamic process. The electricity input to the GSHP can be reduced by increasing the COP of the system. However, the COP of a GSHP system will be different for heating and cooling mode operations. Hence in order to reduce the electricity input to the GSHP, an optimum value of COP has to be determined when GSHP is operated in both heating and cooling modes. In the present research, a methodology is proposed to optimize the operating parameters of a GSHP system which will operate on both heating and cooling modes. Condenser inlet temperature, condenser outlet temperature, dryness fraction at evaporator inlet and evaporator outlet temperature are considered as the influencing parameters of the heat pump. Optimization of these parameters for only heating or only cooling mode operation is achieved by employing Taguchi method for three level variations of the above parameters using an L 9 (3 4 ) orthogonal array. Higher the better concept has been used to get a higher COP. A computer program in FORTAN has been developed to carry out the computations and the results have been analyzed for the optimum conditions using Signal-to-Noise (SN) ratio and Analysis Of Variance (ANOVA) method. Based on this analysis, the maximum COP for only heating and only cooling operation are obtained as 4.25 and 3.32 respectively. By making use of the utility concept both the higher values of COP obtained for heating and cooling modes are optimized to get a single optimum COP for heating and cooling modes. A single

Performance Optimization of Electrical Discharge Machining (Die Sinker for Al-6061 via Taguchi Approach

Directory of Open Access Journals (Sweden)

Muhammad Qaiser Saleem

2015-04-01

Full Text Available This paper parametrically optimizes the EDM (Electrical Discharge Machining process in die sinking mode for material removal rate, surface roughness and edge quality of aluminum alloy Al-6061. The effect of eight parameters namely discharge current, pulse on-time, pulse off-time, auxiliary current, working time, jump time distance, servo speed and work piece hardness are investigated. Taguchi's orthogonal array L18 is employed herein for experimentation. ANOVA (Analysis of Variance with F-ratio criterion at 95% confidence level is used for identification of significant parameters whereas SNR (Signal to Noise Ratio is used for determination of optimum levels. Optimization obtained for Al-6061 with parametric combination investigated herein is validated by the confirmation run.

Taguchi design optimization of machining parameters on the CNC end milling process of halloysite nanotube with aluminium reinforced epoxy matrix (HNT/Al/Ep hybrid composite

Directory of Open Access Journals (Sweden)

J.S. Pang

2014-08-01

Full Text Available This paper introduces the application of Taguchi optimization methodology in optimizing the cutting parameters of end-milling process for machining the halloysite nanotubes (HNTs with aluminium reinforced epoxy hybrid composite material under dry condition. The machining parameters which are chosen to be evaluated in this study are the depth of cut (d, cutting speed (S and feed rate (f. While, the response factors to be measured are the surface roughness of the machined composite surface and the cutting force. An orthogonal array of the Taguchi method was set-up and used to analyse the effect of the milling parameters on the surface roughness and cutting force. The result from this study shows that the application of the Taguchi method can determine the best combination of machining parameters that can provide the optimal machining response conditions which are the lowest surface roughness and lowest cutting force value. For the best surface finish, A1–B3–C3 (d = 0.4 mm, S = 1500 rpm, f = 60 mmpm is found to be the optimized combination of levels for all the three control factors from the analysis. Meanwhile, the optimized combination of levels for all the three control factors from the analysis which provides the lowest cutting force was found to be A2–B2–C2 (d = 0.6 mm, S = 1000 rpm, f = 40 mmpm.

Multi response optimization of internal grinding process parameters for outer ring using Taguchi method and PCR-TOPSIS

Science.gov (United States)

Wisnuadi, Alief Regyan; Damayanti, Retno Wulan; Pujiyanto, Eko

2018-02-01

Bearing is one of the most widely used parts in automotive industry. One of the leading bearing manufacturing companies in the world is SKF Indonesia. This company must produce bearing with international standard. SKF Indonesia must do continuous improvement in order to face competition. During this time, SKF Indonesia is only performing quality control at its Quality Assurance department. In other words, quality improvement at SKF Indonesia has not been done thoroughly. The purpose of this research is to improve quality of outer ring product at SKF Indonesia by conducting an internal grinding process experiment about setting speed ratio, fine position, and spark out grinding time. The specific purpose of this experiment is to optimize some quality responses such as roughness, roundness, and cycle time. All of the response in this experiment were smaller the better. Taguchi method and PCR-TOPSIS are used for the optimization process. The result of this research shows that by using Taguchi method and PCR-TOPSIS, the optimum condition occurs on speed ratio 36, fine position 18 µm/s and spark out 0.5 s. The optimum conditions result were roughness 0.398 µm, roundness 1.78 µm and cycle time 8.1 s. This results have been better than the previous results and meet the standards. The roughness of 0.523 µm decrease to 0.398 µm and the average cycle time of 8.5 s decrease to 8.1 s.

Optimization of laccase production from Marasmiellus palmivorus LA1 by Taguchi method of Design of experiments.

Science.gov (United States)

Chenthamarakshan, Aiswarya; Parambayil, Nayana; Miziriya, Nafeesathul; Soumya, P S; Lakshmi, M S Kiran; Ramgopal, Anala; Dileep, Anuja; Nambisan, Padma

2017-02-13

Fungal laccase has profound applications in different fields of biotechnology due to its broad specificity and high redox potential. Any successful application of the enzyme requires large scale production. As laccase production is highly dependent on medium components and cultural conditions, optimization of the same is essential for efficient product production. Production of laccase by fungal strain Marasmiellus palmivorus LA1 under solid state fermentation was optimized by the Taguchi design of experiments (DOE) methodology. An orthogonal array (L8) was designed using Qualitek-4 software to study the interactions and relative influence of the seven selected factors by one factor at a time approach. The optimum condition formulated was temperature (28 °C), pH (5), galactose (0.8%w/v), cupric sulphate (3 mM), inoculum concentration (number of mycelial agar pieces) (6Nos.) and substrate length (0.05 m). Overall yield increase of 17.6 fold was obtained after optimization. Statistical optimization leads to the elimination of an insignificant medium component ammonium dihydrogen phosphate from the process and contributes to a 1.06 fold increase in enzyme production. A final production of 667.4 ± 13 IU/mL laccase activity paves way for the application of this strain for industrial applications. Study optimized lignin degrading laccases from Marasmiellus palmivorus LA1. This laccases can thus be used for further applications in different scales of production after analyzing the properties of the enzyme. Study also confirmed the use of taguchi method for optimizations of product production.

Optimization of Parameters for Manufacture Nanopowder Bioceramics at Machine Pulverisette 6 by Taguchi and ANOVA Method

Science.gov (United States)

Van Hoten, Hendri; Gunawarman; Mulyadi, Ismet Hari; Kurniawan Mainil, Afdhal; Putra, Bismantoloa dan

2018-02-01

This research is about manufacture nanopowder Bioceramics from local materials used Ball Milling for biomedical applications. Source materials for the manufacture of medicines are plants, animal tissues, microbial structures and engineering biomaterial. The form of raw material medicines is a powder before mixed. In the case of medicines, research is to find sources of biomedical materials that will be in the nanoscale powders can be used as raw material for medicine. One of the biomedical materials that can be used as raw material for medicine is of the type of bioceramics is chicken eggshells. This research will develop methods for manufacture nanopowder material from chicken eggshells with Ball Milling using the Taguchi method and ANOVA. Eggshell milled using a variation of Milling rate on 150, 200 and 250 rpm, the time variation of 1, 2 and 3 hours and variations the grinding balls to eggshell powder weight ratio (BPR) 1: 6, 1: 8, 1: 10. Before milled with Ball Milling crushed eggshells in advance and calcinate to a temperature of 900°C. After the milled material characterization of the fine powder of eggshell using SEM to see its size. The result of this research is optimum parameter of Taguchi Design analysis that is 250 rpm milling rate, 3 hours milling time and BPR is 1: 6 with the average eggshell powder size is 1.305 μm. Milling speed, milling time and ball to powder weight of ratio have contribution successively equal to 60.82%, 30.76% and 6.64% by error equal to 1.78%.

Improved Stress Corrosion Cracking Resistance and Strength of a Two-Step Aged Al-Zn-Mg-Cu Alloy Using Taguchi Method

Science.gov (United States)

Lin, Lianghua; Liu, Zhiyi; Ying, Puyou; Liu, Meng

2015-12-01

Multi-step heat treatment effectively enhances the stress corrosion cracking (SCC) resistance but usually degrades the mechanical properties of Al-Zn-Mg-Cu alloys. With the aim to enhance SCC resistance as well as strength of Al-Zn-Mg-Cu alloys, we have optimized the process parameters during two-step aging of Al-6.1Zn-2.8Mg-1.9Cu alloy by Taguchi's L9 orthogonal array. In this work, analysis of variance (ANOVA) was performed to find out the significant heat treatment parameters. The slow strain rate testing combined with scanning electron microscope and transmission electron microscope was employed to study the SCC behaviors of Al-Zn-Mg-Cu alloy. Results showed that the contour map produced by ANOVA offered a reliable reference for selection of optimum heat treatment parameters. By using this method, a desired combination of mechanical performances and SCC resistance was obtained.

An Investigation On Air and Thermal Transmission Through Knitted Fabric Structures Using the Taguchi Method

Directory of Open Access Journals (Sweden)

Ghosh Anindya

2017-06-01

Full Text Available Knitted fabrics have excellent comfort properties because of their typical porous structure. Different comfort properties of knitted fabrics such as air permeability, thermal absorptivity, and thermal conductivity depend on the properties of raw material and knitting parameters. In this paper, an investigation was done to observe the effect of yarn count, loop length, knitting speed, and yarn input tension in the presence of two uncontrollable noise factors on selected comfort properties of single jersey and 1×1 rib knitted fabrics using the Taguchi experimental design. The results show that yarn count and loop length have significant influence on the thermo-physiological comfort properties of knitted fabrics.

Application of the Taguchi technique for the optimization of surface roughness and tool life during the milling of Hastelloy C22

International Nuclear Information System (INIS)

Kivak, Turgay; Mert, Senol

2017-01-01

In this study, the effects of machining parameters on surface roughness (Ra) and tool life (Tl) were investigated in the milling of Hastelloy C22 alloy with TiAlN-coated carbide inserts. A number of milling experiments were conducted using the L_2_7 (3"3) Taguchi orthogonal array on a CNC milling machine under different cutting conditions (dry, compressed air and wet). The cutting condition, cutting speed and feed rate were determined as the essential machining parameters. Analysis of variance (ANOVA) and signal-to-noise (S/N) ratio were employed to evaluate the effects of the machining parameters on Ra and Tl, and prediction models were created using quadratic regression analyses. The results revealed that the feed rate and cutting condition were the most influential factors on surface roughness and flank wear. The maximum tool life was achieved under wet cutting condition using a cutting speed of 30 x min"-"1 and a feed rate of 0.08 mm x rev"-"1, while the minimum surface roughness value was obtained under wet cutting condition using a cutting speed of 50 m x min"-"1 and the same feed rate. Using the optimum cutting parameters for Tl (30 m x min"-"1, 0.08 mm x rev"-"1), increases of 234 % and 67 % in tool life were observed under wet and compressed air cutting conditions, respectively, compared to the dry cutting condition.

Application of the Taguchi technique for the optimization of surface roughness and tool life during the milling of Hastelloy C22

Energy Technology Data Exchange (ETDEWEB)

Kivak, Turgay; Mert, Senol [Duezce Univ. (Turkey). Dept. of Manufacturing Engineering

2017-02-01

In this study, the effects of machining parameters on surface roughness (Ra) and tool life (Tl) were investigated in the milling of Hastelloy C22 alloy with TiAlN-coated carbide inserts. A number of milling experiments were conducted using the L{sub 27} (3{sup 3}) Taguchi orthogonal array on a CNC milling machine under different cutting conditions (dry, compressed air and wet). The cutting condition, cutting speed and feed rate were determined as the essential machining parameters. Analysis of variance (ANOVA) and signal-to-noise (S/N) ratio were employed to evaluate the effects of the machining parameters on Ra and Tl, and prediction models were created using quadratic regression analyses. The results revealed that the feed rate and cutting condition were the most influential factors on surface roughness and flank wear. The maximum tool life was achieved under wet cutting condition using a cutting speed of 30 x min{sup -1} and a feed rate of 0.08 mm x rev{sup -1}, while the minimum surface roughness value was obtained under wet cutting condition using a cutting speed of 50 m x min{sup -1} and the same feed rate. Using the optimum cutting parameters for Tl (30 m x min{sup -1}, 0.08 mm x rev{sup -1}), increases of 234 % and 67 % in tool life were observed under wet and compressed air cutting conditions, respectively, compared to the dry cutting condition.

Surface Roughness Optimization Using Taguchi Method of High Speed End Milling For Hardened Steel D2

Science.gov (United States)

Hazza Faizi Al-Hazza, Muataz; Ibrahim, Nur Asmawiyah bt; Adesta, Erry T. Y.; Khan, Ahsan Ali; Abdullah Sidek, Atiah Bt.

2017-03-01

The main challenge for any manufacturer is to achieve higher quality of their final products with maintains minimum machining time. In this research final surface roughness analysed and optimized with maximum 0.3 mm flank wear length. The experiment was investigated the effect of cutting speed, feed rate and depth of cut on the final surface roughness using D2 as a work piece hardened to 52-56 HRC, and coated carbide as cutting tool with higher cutting speed 120-240 mm/min. The experiment has been conducted using L9 design of Taguchi collection. The results have been analysed using JMP software.

Environmental testing techniques for electronics and materials

CERN Document Server

Dummer, Geoffrey W A; Fry, D W; Higinbotham, W

2013-01-01

Environmental Testing Techniques for Electronics and Materials reviews environmental testing techniques for evaluating the performance of electronic equipment, components, and materials. Environmental test planning, test methods, and instrumentation are described, along with the general environmental conditions under which equipment must operate. This book is comprised of 15 chapters and begins by explaining why environmental testing is necessary and describing the environment in which electronics must operate. The next chapter considers how an environmental test plan is designed; the methods

Optimization design of a gating system for sand casting aluminium A356 using a Taguchi method and multi-objective culture-based QPSO algorithm

Directory of Open Access Journals (Sweden)

Wen-Jong Chen

2016-04-01

Full Text Available This article combined Taguchi method and analysis of variance with the culture-based quantum-behaved particle swarm optimization to determine the optimal models of gating system for aluminium (Al A356 sand casting part. First, the Taguchi method and analysis of variance were, respectively, applied to establish an L27(38 orthogonal array and determine significant process parameters, including riser diameter, pouring temperature, pouring speed, riser position and gating diameter. Subsequently, a response surface methodology was used to construct a second-order regression model, including filling time, solidification time and oxide ratio. Finally, the culture-based quantum-behaved particle swarm optimization was used to determine the multi-objective Pareto optimal solutions and identify corresponding process conditions. The results showed that the proposed method, compared with initial casting model, enabled reducing the filling time, solidification time and oxide ratio by 68.14%, 50.56% and 20.20%, respectively. A confirmation experiment was verified to be able to effectively reduce the defect of casting and improve the casting quality.

Optimization of Performance and Emission Characteristics of Diesel Engine with Biodiesel Using Grey-Taguchi Method

Directory of Open Access Journals (Sweden)

Goutam Pohit

2013-01-01

Full Text Available Engine performances and emission characteristics of Karanja oil methyl ester blended with diesel were carried out on a variable compression diesel engine. In order to search for the optimal process response through a limited number of experiment runs, application of Taguchi method in combination with grey relational analysis had been applied for solving a multiple response optimization problem. Using grey relational grade and signal-to-noise ratio as a performance index, a particular combination of input parameters was predicted so as to achieve optimum response characteristics. It was observed that a blend of fifty percent was most suitable for use in a diesel engine without significantly affecting the engine performance and emissions characteristics.

Dimensional accuracy optimization of the micro-plastic injection molding process using the Taguchi design method

Directory of Open Access Journals (Sweden)

Chil-Chyuan KUO KUO

2015-06-01

Full Text Available Plastic injection molding is an important field in manufacturing industry because there are many plastic products that produced by injection molding. However, the time and cost required for producing a precision mold are the most troublesome problems that limit the application at the development stage of a new product in precision machinery industry. This study presents an approach of manufacturing a hard mold with microfeatures for micro-plastic injection molding. This study also focuses on Taguchi design method for investigating the effect of injection parameters on the dimensional accuracy of Fresnel lens during plastic injection molding. It was found that the dominant factor affecting the microgroove depth of Fresnel lens is packing pressure. The optimum processing parameters are packing pressure of 80 MPa, melt temperature of 240 °C, mold temperature of 90 °C and injection speed of 50 m/s. The dimensional accuracy of Fresnel lens can be controlled within ±3 µm using the optimum level of process parameters through the confirmation test. The research results of this study have industrial application values because electro-optical industries are able to significantly reduce a new optical element development cycle time.DOI: http://dx.doi.org/10.5755/j01.ms.21.2.5864

Multi-response optimization of process parameters using Taguchi method and grey relational analysis during turning AA 7075/SiC composite in dry and spray cooling environments

Directory of Open Access Journals (Sweden)

P. C. Mishra

2015-09-01

Full Text Available Turning experiments were carried out on AA 7075/SiC composite workpiece in dry and spray cooling environments based on L16 Taguchi design of experiments. Multiple performance optimization of process parameters was performed using grey relational analysis. The performance characteristics considered were average surface roughness, cutting tool temperature and material removal rate. Uncoated carbide inserts were used for machining the workpiece in a high speed precision lathe. A grey relational grade obtained from grey relational analysis was used to optimize the process parameters. Optimal combination of process parameters was then determined by the Taguchi method using the grey relational grade as the performance index. Experimental results indicated that the turning in spray cooling environment was beneficial compared to that in dry environment for the quality response characteristics under consideration. Analysis of variance showed that feed was the most significant parameter for the multiple performance characteristics during turning in both the environments.

Magnetic Nondestructive Testing Techniques of Constructional Steel

Directory of Open Access Journals (Sweden)

Xiong Er-gang

2016-01-01

Full Text Available Steel is a kind of ferromagnetic material, which is extensively applied in such fields as buildings, bridges, railways, machines and lifeline engineering etc. Those engineering structures built of constructional steel will unavoidably experience some damages during their service lifetime, thus which will influence the distribution regularity of internal forces in structures, result in over-stresses, cause the local failure of structures, and even lead to collapse of the whole structure. Therefore, it is a pressing topic to study how to directly evaluate the real-time stressed states of structural members, damages and steel characteristics in present structural health monitoring and diagnosing fields. And the achievements of this research will be of theoretical significance and of application value of engineering. This paper summarizes varieties of new magnetic nondestructive testing techniques used in constructional steel, respectively investigates the testing principles, characteristics and application for the magnetic Barkhausen noise technique, magnetic acoustic emission technique, magnetic flux leakage technique, magnetic memory technique and magnetic absorption technique, and points out the problems present in the application of these new techniques to actual testing and the further research objective.

Optimization of squeeze casting parameters for non symmetrical AC2A aluminium alloy castings through Taguchi method

International Nuclear Information System (INIS)

Senthil, P.; Amirthagadeswaran, K. S.

2012-01-01

This paper reports a research in which an attempt was made to prepare AC2A aluminium alloy castings of a non symmetrical component through squeeze casting process. The primary objective was to investigate the influence of process parameters on mechanical properties of the castings. Experiments were conducted based on orthogonal array suggested in Taguchi's offline quality control concept. The experimental results showed that squeeze pressure, die preheating temperature and compression holding time were the parameters making significant improvement in mechanical properties. The optimal squeeze casting condition was found and mathematical models were also developed for the process

Improvements in skin-testing technique.

Science.gov (United States)

Carr, Warner W

2006-01-01

Allergy skin testing is the primary modality used in the diagnosis of allergic diseases and guides development of treatment and avoidance plans. The goal of the Allergist is to skin test the appropriate population with a device and technique that minimizes pain while maximizing sensitivity and specificity. The debate involving the use of intradermal versus skin-prick testing in the diagnosis of aeroallergy has been long lasting. Past and present medical literature will be reviewed, establishing the lack of diagnostic use of intradermal testing in the setting of aeroallergy. New skin devices continue to be developed with a trend toward production of multidevices. Performance characteristics of various skin test devices will be reviewed with an emphasis on sensitivity, specificity, and variability of skin-prick testing devices. Significant statistical differences exist between all devices tested and reported in the literature. Whether these statistical differences equate to clinical differences is not known. With this review the practicing allergist should carefully evaluate multiple different devices and choose a device that suits their practice needs. In addition, allergists must ensure that technicians are sufficiently trained on the correct use of their device and should conduct continuing education to ensure that proper skin testing techniques are being used in their practice. Finally, the use of skin testing in pediatrics will be reviewed with a focus on safety. Care should be taken when skin testing infants < or = 6 months of age, especially in the setting of eczema and a family history of atopy.

Optimization of friction welding by taguchi and ANOVA method on commercial aluminium tube to Al 2025 tube plate with backing block using an external tool

International Nuclear Information System (INIS)

Kanna, S.; Kumaraswamidhs, L. A.; Kumaran, S. Senthil

2016-01-01

The aim of the present work is to optimize the Friction welding of tube to tube plate using an external tool (FWTPET) with clearance fit of commercial aluminum tube to Al 2025 tube plate using an external tool. Conventional frictional welding is suitable to weld only symmetrical joints either tube to tube or rod to rod but in this research with the help of external tool, the welding has been done by unsymmetrical shape of tube to tube plate also. In this investigation, the various welding parameters such as tool rotating speed (rpm), projection of tube (mm) and depth of cut (mm) are determined according to the Taguchi L9 orthogonal array. The two conditions were considered in this process to examine this experiment; where condition 1 is flat plate with plain tube Without holes [WOH] on the circumference of the surface and condition 2 is flat plate with plane tube has holes on its circumference of the surface With holes [WH]. Taguchi L9 orthogonal array was utilized to find the most significant control factors which will yield better joint strength. Besides, the most influential process parameter has been determined using statistical Analysis of variance (ANOVA). Finally, the comparison of each result has been done for conditions by means percentage of contribution and regression analysis. The general regression equation is formulated and better strength is obtained and it is validated by means of confirmation test. It was observed that value of optimal welded joint strength for both tube without holes and tube with holes are to be 319.485 MPa and 264.825 MPa, respectively.

Optimization of friction welding by taguchi and ANOVA method on commercial aluminium tube to Al 2025 tube plate with backing block using an external tool

Energy Technology Data Exchange (ETDEWEB)

Kanna, S.; Kumaraswamidhs, L. A. [Indian Institute of Technology, Dhanbad (India); Kumaran, S. Senthil [RVS School of Engineering and Technology, Dindigul (India)

2016-05-15

The aim of the present work is to optimize the Friction welding of tube to tube plate using an external tool (FWTPET) with clearance fit of commercial aluminum tube to Al 2025 tube plate using an external tool. Conventional frictional welding is suitable to weld only symmetrical joints either tube to tube or rod to rod but in this research with the help of external tool, the welding has been done by unsymmetrical shape of tube to tube plate also. In this investigation, the various welding parameters such as tool rotating speed (rpm), projection of tube (mm) and depth of cut (mm) are determined according to the Taguchi L9 orthogonal array. The two conditions were considered in this process to examine this experiment; where condition 1 is flat plate with plain tube Without holes [WOH] on the circumference of the surface and condition 2 is flat plate with plane tube has holes on its circumference of the surface With holes [WH]. Taguchi L9 orthogonal array was utilized to find the most significant control factors which will yield better joint strength. Besides, the most influential process parameter has been determined using statistical Analysis of variance (ANOVA). Finally, the comparison of each result has been done for conditions by means percentage of contribution and regression analysis. The general regression equation is formulated and better strength is obtained and it is validated by means of confirmation test. It was observed that value of optimal welded joint strength for both tube without holes and tube with holes are to be 319.485 MPa and 264.825 MPa, respectively.

Optimization of Experimental Conditions of the Pulsed Current GTAW Parameters for Mechanical Properties of SDSS UNS S32760 Welds Based on the Taguchi Design Method

Science.gov (United States)

Yousefieh, M.; Shamanian, M.; Saatchi, A.

2012-09-01

Taguchi design method with L9 orthogonal array was implemented to optimize the pulsed current gas tungsten arc welding parameters for the hardness and the toughness of super duplex stainless steel (SDSS, UNS S32760) welds. In this regard, the hardness and the toughness were considered as performance characteristics. Pulse current, background current, % on time, and pulse frequency were chosen as main parameters. Each parameter was varied at three different levels. As a result of pooled analysis of variance, the pulse current is found to be the most significant factor for both the hardness and the toughness of SDSS welds by percentage contribution of 71.81 for hardness and 78.18 for toughness. The % on time (21.99%) and the background current (17.81%) had also the next most significant effect on the hardness and the toughness, respectively. The optimum conditions within the selected parameter values for hardness were found as the first level of pulse current (100 A), third level of background current (70 A), first level of % on time (40%), and first level of pulse frequency (1 Hz), while they were found as the second level of pulse current (120 A), second level of background current (60 A), second level of % on time (60%), and third level of pulse frequency (5 Hz) for toughness. The Taguchi method was found to be a promising tool to obtain the optimum conditions for such studies. Finally, in order to verify experimental results, confirmation tests were carried out at optimum working conditions. Under these conditions, there were good agreements between the predicted and the experimental results for the both hardness and toughness.

Quality in the Operational Air Force: A Case of Misplaced Emphasis

Science.gov (United States)

1994-05-01

other quality advocates of the era. These men included Joseph Juran, Armand Feigenbaum, Kaoru Ishikawa , and Genichi Taguchi. Juran contributed disciplined...planning theories, while Feigenbaum felt that producing quality could actually reduce production costs. In addition, Ishikawa and Taguchi lent...statistically based problem solving techniques, but the more modem approaches of Ishikawa , Taguchi and others. The operative concept of TQM is ’continuous

An Investigation of Optimum NLC-Sunscreen Formulation Using Taguchi Analysis

Directory of Open Access Journals (Sweden)

Pao Chi Chen

2013-01-01

Full Text Available This study used three kinds of wax and three kinds of oil, with fixed mixture ratio including UV-blocking materials of ethylhexyl methoxycinnamate, oxybenzone, and avobenzone, and applied hot high-pressure homogenization process to prepare nanolipid sunscreen formulations. The measured particle size of the sunscreen formulations was 100~300 nm around PDI of 0.2 having a moderate polydisperse system. The distribution of zeta potential was −50 mV to −35 mV, showing a stable system. The UV light-absorbing range of 9 groups of sunscreen formulations was 275 nm~380 nm ranging within UVA and UVB. The rheological analysis found that the viscosity change is shear, thinning exhibiting colloid behavior. Taguchi analysis found that the optimum combinations are the carnauba wax and the blackcurrant oil combination for crystallinity and the beeswax and CPG oil for UV absorption. In addition, UV-blocking ability shows that the SPF was 51.5 and PFA was three stars for SU9 formulation. Finally, the effect of temperature on the properties of sunscreen formulations was also explored.

Optimization of field emission properties of carbon nanotubes by Taguchi method

International Nuclear Information System (INIS)

Ting, J.-H.; Chang, C.-C.; Chen, S.-L.; Lu, D.-S.; Kung, C.-Y.; Huang, F.-Y.

2006-01-01

It is the purpose of this study to evaluate the field emission property of carbon nanotubes (CNTs) prepared by microwave plasma-enhanced chemical vapor deposition (MPCVD) method. Nickel layer of 5 nm in thickness on 20-nm thickness titanium nitride film was transformed into discrete islands after hydrogen plasma pretreatment. CNTs were then grown up on Ni-coated areas by MPCVD. Through the practice of Taguchi method, superior CNT films with very low emission onset electric field, about 0.7 V/μm (at J = 10 μA/cm 2 ), are attained without post-deposition treatment. It is found that microwave power has the most important influence on the field emission characteristics of CNT films. The increase of methane flow ratio will downgrade the degree of graphitization of CNT and thus its field emission characteristics. Scanning electron microscope and transmission electron microscopy (TEM) observation and energy dispersive X-ray spectrometer analysis reveal that CNT growth by MPCVD is based on tip-growth mechanism. TEM micrographs validate the hollow, bamboo-like structure of the multi-walled CNTs

OPTIMASI PROSES PEMBUATAN BRIKET BIOMASSA MENGGUNAKAN METODE TAGUCHI GUNA MEMENUHI KEBUTUHAN BAHAN BAKAR ALTERNATIF YANG RAMAH LINGKUNGAN (Optimization of Biomass Briquettes Production Process Using Taguchi Method

Directory of Open Access Journals (Sweden)

Musabbikhah Musabbikhah

2015-03-01

Full Text Available ABSTRAK Permasalahan yang dihadapi pembuat dan pengguna briket adalah briket yang dihasilkan kualitasnya rendah ditinjau dari nilai kalor. Tujuan penelitian ini adalah menentukan kualitas briket terbaik dari limbah biomassa dalam memenuhi kebutuhan bahan bakar alternatif rumah tangga yang murah dan ramah lingkungan guna mewujudkan masyarakat mandiri energi. Metode yang digunakan untuk menentukan kualitas briket adalah metode Taguchi. Variabel bebas dalam penelitian ini adalah tekanan pengepressan, waktu penahanan, model cetakan, suhu pengeringan, lama pengeringan dan komposisi bahan, sedangkan variabel terikat adalah nilai kalor briket. Hasil penelitian menunjukkan bahwa kualitas briket terbaik ditinjau dari nilai kalor tertinggi yaitu pada setting parameter A2B1C2D2E2F1, artinya tekanan pengepressan 225 kg/cm2, waktu penahanan 5 menit, model cetakan sarang tawon (kotak, suhu pengeringan 60 °C, lama pengeringan 3 hari, perbandingan limbah jarak pagar : arang sekam : arang tempurung kelapa : perekat adalah 5 : 3: 2 : 1. Rata-rata nilai kalor biobriket yang dihasilkan sebesar 5.323 kal/g. Hal ini menunjukkan bahwa briket mempunyai nilai kalor yang tinggi dan memenuhi SNI, sehingga briket layak untuk memenuhi kebutuhan bahan bakar alternatif yang ramah lingkungan. ABSTRACT Problems that encountered on manufacturers and users of briquettes is low quality of the briquettes in terms of heat value. The aim of this research is to determine the best quality of the briquette which is made from biomass waste. The briquette is expected to be used to fulfill the need of inexpensive and environmentally friendly of alternative household fuel, by which the energy independent community could be realized.The method used to determine the quality of the briquette is Taguchi method. The independent variables involved are compressive strength, holding time, mold model, drying temperature, drying time and material composition. The dependent variable is the highest

Optimization of Injection Molding Parameters for HDPE/TiO₂ Nanocomposites Fabrication with Multiple Performance Characteristics Using the Taguchi Method and Grey Relational Analysis.

Science.gov (United States)

Pervez, Hifsa; Mozumder, Mohammad S; Mourad, Abdel-Hamid I

2016-08-22

The current study presents an investigation on the optimization of injection molding parameters of HDPE/TiO₂ nanocomposites using grey relational analysis with the Taguchi method. Four control factors, including filler concentration (i.e., TiO₂), barrel temperature, residence time and holding time, were chosen at three different levels of each. Mechanical properties, such as yield strength, Young's modulus and elongation, were selected as the performance targets. Nine experimental runs were carried out based on the Taguchi L₉ orthogonal array, and the data were processed according to the grey relational steps. The optimal process parameters were found based on the average responses of the grey relational grades, and the ideal operating conditions were found to be a filler concentration of 5 wt % TiO₂, a barrel temperature of 225 °C, a residence time of 30 min and a holding time of 20 s. Moreover, analysis of variance (ANOVA) has also been applied to identify the most significant factor, and the percentage of TiO₂ nanoparticles was found to have the most significant effect on the properties of the HDPE/TiO₂ nanocomposites fabricated through the injection molding process.

Application of Taguchi L16 design method for comparative study of ability of 3A zeolite in removal of Rhodamine B and Malachite green from environmental water samples

Science.gov (United States)

Rahmani, Mashaallah; Kaykhaii, Massoud; Sasani, Mojtaba

2018-01-01

This study aimed to investigate the efficiency of 3A zeolite as a novel adsorbent for removal of Rhodamine B and Malachite green dyes from water samples. To increase the removal efficiency, effecting parameters on adsorption process were investigated and optimized by adopting Taguchi design of experiments approach. The percentage contribution of each parameter on the removal of Rhodamine B and Malachite green dyes determined using ANOVA and showed that the most effective parameters in removal of RhB and MG by 3A zeolite are initial concentration of dye and pH, respectively. Under optimized condition, the amount predicted by Taguchi design method and the value obtained experimentally, showed good closeness (more than 94.86%). Good adsorption efficiency obtained for proposed methods indicates that, the 3A zeolite is capable to remove the significant amounts of Rhodamine B and Malachite green from environmental water samples.

High voltage test techniques

CERN Document Server

Kind, Dieter

2001-01-01

The second edition of High Voltage Test Techniques has been completely revised. The present revision takes into account the latest international developments in High Voltage and Measurement technology, making it an essential reference for engineers in the testing field.High Voltage Technology belongs to the traditional area of Electrical Engineering. However, this is not to say that the area has stood still. New insulating materials, computing methods and voltage levels repeatedly pose new problems or open up methods of solution; electromagnetic compatibility (EMC) or components and systems al

Effect of dielectric fluid with surfactant and graphite powder on Electrical Discharge Machining of titanium alloy using Taguchi method

Directory of Open Access Journals (Sweden)

Murahari Kolli

2015-12-01

Full Text Available In this paper, Taguchi method was employed to optimize the surfactant and graphite powder concentration in dielectric fluid for the machining of Ti-6Al-4V using Electrical Discharge Machining (EDM. The process parameters such as discharge current, surfactant concentration and powder concentration were changed to explore their effects on Material Removal Rate (MRR, Surface Roughness (SR, Tool wear rate (TWR and Recast Layer Thickness (RLT. Detailed analysis of structural features of machined surface was carried out using Scanning Electron Microscope (SEM to observe the influence of surfactant and graphite powder on the machining process. It was observed from the experimental results that the graphite powder and surfactant added dielectric fluid significantly improved the MRR, reduces the SR, TWR and RLT at various conditions. Analysis of Variance (ANOVA and F-test of experimental data values related to the important process parameters of EDM revealed that discharge current and surfactant concentration has more percentage of contribution on the MRR and TWR whereas the SR, and RLT were found to be affected greatly by the discharge current and graphite powder concentration.

Test Concept for Advanced Oxidation Techniques

DEFF Research Database (Denmark)

Bennedsen, Lars Rønn; Søgaard, Erik Gydesen; Mortensen, Lars

advanced on-site oxidation tests. The remediation techniques included are electrochemical oxidation, photochemical/photocatalytic oxidation, ozone, hydrogen peroxide, permanganate, and persulfate among others. A versatile construction of the mobile test unit makes it possible to combine different...

Anatomical Thin Titanium Mesh Plate Structural Optimization for Zygomatic-Maxillary Complex Fracture under Fatigue Testing

Directory of Open Access Journals (Sweden)

Yu-Tzu Wang

2018-01-01

Full Text Available This study performs a structural optimization of anatomical thin titanium mesh (ATTM plate and optimal designed ATTM plate fabricated using additive manufacturing (AM to verify its stabilization under fatigue testing. Finite element (FE analysis was used to simulate the structural bending resistance of a regular ATTM plate. The Taguchi method was employed to identify the significance of each design factor in controlling the deflection and determine an optimal combination of designed factors. The optimal designed ATTM plate with patient-matched facial contour was fabricated using AM and applied to a ZMC comminuted fracture to evaluate the resting maxillary micromotion/strain under fatigue testing. The Taguchi analysis found that the ATTM plate required a designed internal hole distance to be 0.9 mm, internal hole diameter to be 1 mm, plate thickness to be 0.8 mm, and plate height to be 10 mm. The designed plate thickness factor primarily dominated the bending resistance up to 78% importance. The averaged micromotion (displacement and strain of the maxillary bone showed that ZMC fracture fixation using the miniplate was significantly higher than those using the AM optimal designed ATTM plate. This study concluded that the optimal designed ATTM plate with enough strength to resist the bending effect can be obtained by combining FE and Taguchi analyses. The optimal designed ATTM plate with patient-matched facial contour fabricated using AM provides superior stabilization for ZMC comminuted fractured bone segments.

Optimization of Injection Molding Parameters for HDPE/TiO2 Nanocomposites Fabrication with Multiple Performance Characteristics Using the Taguchi Method and Grey Relational Analysis

Directory of Open Access Journals (Sweden)

Hifsa Pervez

2016-08-01

Full Text Available The current study presents an investigation on the optimization of injection molding parameters of HDPE/TiO2 nanocomposites using grey relational analysis with the Taguchi method. Four control factors, including filler concentration (i.e., TiO2, barrel temperature, residence time and holding time, were chosen at three different levels of each. Mechanical properties, such as yield strength, Young’s modulus and elongation, were selected as the performance targets. Nine experimental runs were carried out based on the Taguchi L9 orthogonal array, and the data were processed according to the grey relational steps. The optimal process parameters were found based on the average responses of the grey relational grades, and the ideal operating conditions were found to be a filler concentration of 5 wt % TiO2, a barrel temperature of 225 °C, a residence time of 30 min and a holding time of 20 s. Moreover, analysis of variance (ANOVA has also been applied to identify the most significant factor, and the percentage of TiO2 nanoparticles was found to have the most significant effect on the properties of the HDPE/TiO2 nanocomposites fabricated through the injection molding process.

Optimization of Injection Molding Parameters for HDPE/TiO2 Nanocomposites Fabrication with Multiple Performance Characteristics Using the Taguchi Method and Grey Relational Analysis

Science.gov (United States)

Pervez, Hifsa; Mozumder, Mohammad S.; Mourad, Abdel-Hamid I.

2016-01-01

The current study presents an investigation on the optimization of injection molding parameters of HDPE/TiO2 nanocomposites using grey relational analysis with the Taguchi method. Four control factors, including filler concentration (i.e., TiO2), barrel temperature, residence time and holding time, were chosen at three different levels of each. Mechanical properties, such as yield strength, Young’s modulus and elongation, were selected as the performance targets. Nine experimental runs were carried out based on the Taguchi L9 orthogonal array, and the data were processed according to the grey relational steps. The optimal process parameters were found based on the average responses of the grey relational grades, and the ideal operating conditions were found to be a filler concentration of 5 wt % TiO2, a barrel temperature of 225 °C, a residence time of 30 min and a holding time of 20 s. Moreover, analysis of variance (ANOVA) has also been applied to identify the most significant factor, and the percentage of TiO2 nanoparticles was found to have the most significant effect on the properties of the HDPE/TiO2 nanocomposites fabricated through the injection molding process. PMID:28773830

High-voltage test and measuring techniques

CERN Document Server

Hauschild, Wolfgang

2014-01-01

It is the intent of this book to combine high-voltage (HV) engineering with HV testing technique and HV measuring technique. Based on long-term experience gained by the authors as lecturer and researcher as well as member in international organizations, such as IEC and CIGRE, the book will reflect the state of the art as well as the future trends in testing and diagnostics of HV equipment to ensure a reliable generation, transmission and distribution of electrical energy. The book is intended not only for experts but also for students in electrical engineering and high-voltage engineering.

Model development for mechanical properties and weld quality class of friction stir welding using multi-objective Taguchi method and response surface methodology

Energy Technology Data Exchange (ETDEWEB)

Mohamed, Mohamed Ackiel [University Kuala Lumpur Malaysia France Institute, Bandar Baru Bangi (Malaysia); Manurung, Yupiter HP; Berhan, Mohamed Nor [Universiti Teknologi MARA, Shah Alam (Malaysia)

2015-06-15

This study presents the effect of the governing parameters in friction stir welding (FSW) on the mechanical properties and weld quality of a 6mm thick 6061 T651 Aluminum alloy butt joint. The main FSW parameters, the rotational and traverse speed were optimized based on multiple mechanical properties and quality features, which focus on the tensile strength, hardness and the weld quality class using the multi-objective Taguchi method (MTM). Multi signal to noise ratio (MSNR) was employed to determine the optimum welding parameters for MTM while further analysis concerning the significant level determination was accomplished via the well-established analysis of variance (ANOVA). Furthermore, the first order model for predicting the mechanical properties and weld quality class is derived by applying response surface methodology (RSM). Based on the experimental confirmation test, the proposed method can effectively estimate the mechanical properties and weld quality class which can be used to enhance the welding performance in FSW or other applications.

Model development for mechanical properties and weld quality class of friction stir welding using multi-objective Taguchi method and response surface methodology

International Nuclear Information System (INIS)

Mohamed, Mohamed Ackiel; Manurung, Yupiter HP; Berhan, Mohamed Nor

2015-01-01

This study presents the effect of the governing parameters in friction stir welding (FSW) on the mechanical properties and weld quality of a 6mm thick 6061 T651 Aluminum alloy butt joint. The main FSW parameters, the rotational and traverse speed were optimized based on multiple mechanical properties and quality features, which focus on the tensile strength, hardness and the weld quality class using the multi-objective Taguchi method (MTM). Multi signal to noise ratio (MSNR) was employed to determine the optimum welding parameters for MTM while further analysis concerning the significant level determination was accomplished via the well-established analysis of variance (ANOVA). Furthermore, the first order model for predicting the mechanical properties and weld quality class is derived by applying response surface methodology (RSM). Based on the experimental confirmation test, the proposed method can effectively estimate the mechanical properties and weld quality class which can be used to enhance the welding performance in FSW or other applications.

Enhancement of anti-tubercular activity and biomass of fermented food associated Staphylococcus hominis strain MANF2 using Taguchi orthogonal array and Box-Behnken design.

Science.gov (United States)

Khusro, Ameer; Aarti, Chirom; Dusthackeer, Azger; Agastian, Paul

2018-04-14

The prime focus of the present investigation was to optimize statistically the anti-tubercular activity and biomass of fermented food associated Staphylococcus hominis strain MANF2 using Taguchi orthogonal array (OA) and Box-Behnken design (BBD). The anti-tubercular activity of strain MANF2 was determined against Mycobacterium tuberculosis H37Rv using luciferase reporter phase assay. Among varied media examined, the isolate exhibited impressive anti-tubercular activity with paramount relative light unit reduction of >90% in de Man Rogose Sharpe (MRS) broth. Primarily, the anti-tubercular activity and biomass of strain MANF2 were estimated in MRS broth by optimizing eight diversified parameters using one factor at a time (OFAT) method after working out a series of experiments. The most significant contributing factors selected through OFAT tool were optimized using Taguchi approach with a standard OA layout of L18 (2 2  × 3 6 ). Results demonstrated the significant (P ≤ 0.05) influence of pH, temperature, yeast extract, magnesium sulphate, and glycerol on response variables. These controlled variables were further optimized using BBD matrix at N = 46 by second-order polynomial equation. The fermentation medium of pH 6.5 constituting yeast extract (0.5% w/v), magnesium sulphate (0.1% w/v), and glycerol (1.5% v/v), being further incubated at 30 °C showed enhanced anti-tubercular activity (98.7%) and approximately 4 fold increment in the bacterial biomass yield (8.3 mg/mL) with respect to traditional OFAT method. Three-dimensional response plots of the quadratic model showed interdependent interaction between the significant variables. In conclusion, the present study revealed the first report on the optimization of anti-tubercular activity and biomass of S. hominis via Taguchi OA as well as BBD design, and thus, paved a path for its proficient applications in pharmaceutical industries as dynamic mycobactericidal agent in future. Copyright © 2018

Preparation of nanocellulose from Imperata brasiliensis grass using Taguchi method.

Science.gov (United States)

Benini, Kelly Cristina Coelho de Carvalho; Voorwald, Herman Jacobus Cornelis; Cioffi, Maria Odila Hilário; Rezende, Mirabel Cerqueira; Arantes, Valdeir

2018-07-15

Cellulose nanoparticles (CNs) were prepared by acid hydrolysis of the cellulose pulp extracted from the Brazilian satintail (Imperata Brasiliensis) plant using a conventional and a total chlorine free method. Initially, a statistical design of experiment was carried out using Taguchi orthogonal array to study the hydrolysis parameters, and the main properties (crystallinity, thermal stability, morphology, and sizes) of the nanocellulose. X-ray diffraction (XRD), fourier-transform infrared spectroscopy (FTIR), field-emission scanning electron microscopy (FE-SEM), dynamic light scattering (DLS), zeta potential and thermogravimetric analysis (TGA) were carried out to characterize the physical-chemical properties of the CNs obtained. Cellulose nanoparticles with diameter ranging from 10 to 60 nm and length between 150 and 250 nm were successfully obtained at sulfuric acid concentration of 64% (m/m), temperature 35 °C, reaction time 75 min, and a 1:20 (g/mL) pulp-to-solution ratio. Under this condition, the Imperata Brasiliensis CNs showed good stability in suspension, crystallinity index of 65%, and a cellulose degradation temperature of about 117 °C. Considering that these properties are similar to those of nanocelluloses from other lignocellulosics feedstocks, Imperata grass seems also to be a suitable source for nanocellulose production. Copyright © 2018 Elsevier Ltd. All rights reserved.

Analysis of the Forces in Micromilling of Hardened AISI H13 Steel with Different Grain Sizes Using the Taguchi Methodology

Directory of Open Access Journals (Sweden)

Carlos Henrique Lauro

2014-05-01

Full Text Available The micromachining process has been applied to the free form and micromolds markets. This has occurred due to the growth in demand for microcomponents. However, micromachining of hardened steels is a challenge due to the reduction in tool life and the increase of the surface roughness when compared with the macromachining process. This paper focused on the analysis of micromilling forces on hardened AISI H13 steel with different grain sizes. Experimental tests were carried out on workpieces with different austenitic grain sizes and a hardness of 46 HRC. Micro-end-mill cutters with a diameter of 0.5 mm and (TiAlN coatings were applied in the milling of workpieces of 11 × 11 mm. The input parameters were two radial depths of cut, two cutting speeds, and two feed rates. The influence of the input parameters on the response cutting force was analyzed using the Taguchi method. Finally, considering the large grain size, the cutting forces in the x-, y-, and z-axes direction were small.

A Secure Test Technique for Pipelined Advanced Encryption Standard

Science.gov (United States)

Shi, Youhua; Togawa, Nozomu; Yanagisawa, Masao; Ohtsuki, Tatsuo

In this paper, we presented a Design-for-Secure-Test (DFST) technique for pipelined AES to guarantee both the security and the test quality during testing. Unlike previous works, the proposed method can keep all the secrets inside and provide high test quality and fault diagnosis ability as well. Furthermore, the proposed DFST technique can significantly reduce test application time, test data volume, and test generation effort as additional benefits.

Microwave Cold-Testing Techniques for the NLC

CERN Document Server

Bowden, G B

1996-01-01

The R and D program for the Next Linear Collider Test Accelerator (NLCTA) includes the development of microwave techniques for testing X-band accelerating structures at different stages of design, manufacturing and assembly. During the design phase, short stacks were built and tested to finalize dimensions. Cell by cell measurements were performed on the NLCTA injector cells as a microwave quality control (QC) after manufacturing. The two injector sections were tuned using a moveable plunger and tested using a semiautomated system of bead-pull. Using this perturbation technique, we were able to map the amplitude and phase of the electric field on the axis throughout the assembled structures under traveling-wave conditions.

Microwave Cold-Testing Techniques for the NLC

International Nuclear Information System (INIS)

Bowden, Gordon B

2003-01-01

The R and D program for the Next Linear Collider Test Accelerator (NLCTA) includes the development of microwave techniques for testing X-band accelerating structures at different stages of design, manufacturing and assembly. During the design phase, short stacks were built and tested to finalize dimensions. Cell by cell measurements were performed on the NLCTA injector cells as a microwave quality control (QC) after manufacturing. The two injector sections were tuned using a moveable plunger and tested using a semiautomated system of bead-pull. Using this perturbation technique, we were able to map the amplitude and phase of the electric field on the axis throughout the assembled structures under traveling-wave conditions

Analysis of WEDM Process Parameters on Surface Roughness and Kerf using Taguchi Method

Directory of Open Access Journals (Sweden)

Asfana Banu

2017-12-01

Full Text Available In obtaining the best quality of engineering parts, the quality of machined surface plays an essential role. The fatigue strength, wear resistance, and corrosion of workpiece are some of the aspects of the qualities that can be improved. This paper investigates the effect of wire electrical discharge machining (WEDM process parameters on surface roughness and kerf on stainless steel using distilled water as dielectric fluid and brass wire as tool electrode. The selected process parameters are voltage open, wire speed, wire tension, voltage gap, and off time. Empirical models using Taguchi method were developed for the estimation of surface roughness and kerf. The analysis revealed that off time has major influence on surface roughness and kerf. The optimum machining parameters for minimum surface roughness and kerf were found to be 10 V open voltage, 2.84 µs off time, 12 m/min wire speed, 6.3 N wire tension, and 54.91 V voltage gap.

Non-Destructive Techniques Based on Eddy Current Testing

Science.gov (United States)

García-Martín, Javier; Gómez-Gil, Jaime; Vázquez-Sánchez, Ernesto

2011-01-01

Non-destructive techniques are used widely in the metal industry in order to control the quality of materials. Eddy current testing is one of the most extensively used non-destructive techniques for inspecting electrically conductive materials at very high speeds that does not require any contact between the test piece and the sensor. This paper includes an overview of the fundamentals and main variables of eddy current testing. It also describes the state-of-the-art sensors and modern techniques such as multi-frequency and pulsed systems. Recent advances in complex models towards solving crack-sensor interaction, developments in instrumentation due to advances in electronic devices, and the evolution of data processing suggest that eddy current testing systems will be increasingly used in the future. PMID:22163754

Improved production of tannase by Klebsiella pneumoniae using Indian gooseberry leaves under submerged fermentation using Taguchi approach.

Science.gov (United States)

Kumar, Mukesh; Singh, Amrinder; Beniwal, Vikas; Salar, Raj Kumar

2016-12-01

Tannase (tannin acyl hydrolase E.C 3.1.1.20) is an inducible, largely extracellular enzyme that causes the hydrolysis of ester and depside bonds present in various substrates. Large scale industrial application of this enzyme is very limited owing to its high production costs. In the present study, cost effective production of tannase by Klebsiella pneumoniae KP715242 was studied under submerged fermentation using different tannin rich agro-residues like Indian gooseberry leaves (Phyllanthus emblica), Black plum leaves (Syzygium cumini), Eucalyptus leaves (Eucalyptus glogus) and Babul leaves (Acacia nilotica). Among all agro-residues, Indian gooseberry leaves were found to be the best substrate for tannase production under submerged fermentation. Sequential optimization approach using Taguchi orthogonal array screening and response surface methodology was adopted to optimize the fermentation variables in order to enhance the enzyme production. Eleven medium components were screened primarily by Taguchi orthogonal array design to identify the most contributing factors towards the enzyme production. The four most significant contributing variables affecting tannase production were found to be pH (23.62 %), tannin extract (20.70 %), temperature (20.33 %) and incubation time (14.99 %). These factors were further optimized with central composite design using response surface methodology. Maximum tannase production was observed at 5.52 pH, 39.72 °C temperature, 91.82 h of incubation time and 2.17 % tannin content. The enzyme activity was enhanced by 1.26 fold under these optimized conditions. The present study emphasizes the use of agro-residues as a potential substrate with an aim to lower down the input costs for tannase production so that the enzyme could be used proficiently for commercial purposes.

Interactive design optimization of magnetorheological-brake actuators using the Taguchi method

Science.gov (United States)

Erol, Ozan; Gurocak, Hakan

2011-10-01

This research explored an optimization method that would automate the process of designing a magnetorheological (MR)-brake but still keep the designer in the loop. MR-brakes apply resistive torque by increasing the viscosity of an MR fluid inside the brake. This electronically controllable brake can provide a very large torque-to-volume ratio, which is very desirable for an actuator. However, the design process is quite complex and time consuming due to many parameters. In this paper, we adapted the popular Taguchi method, widely used in manufacturing, to the problem of designing a complex MR-brake. Unlike other existing methods, this approach can automatically identify the dominant parameters of the design, which reduces the search space and the time it takes to find the best possible design. While automating the search for a solution, it also lets the designer see the dominant parameters and make choices to investigate only their interactions with the design output. The new method was applied for re-designing MR-brakes. It reduced the design time from a week or two down to a few minutes. Also, usability experiments indicated significantly better brake designs by novice users.

Interactive design optimization of magnetorheological-brake actuators using the Taguchi method

International Nuclear Information System (INIS)

Erol, Ozan; Gurocak, Hakan

2011-01-01

This research explored an optimization method that would automate the process of designing a magnetorheological (MR)-brake but still keep the designer in the loop. MR-brakes apply resistive torque by increasing the viscosity of an MR fluid inside the brake. This electronically controllable brake can provide a very large torque-to-volume ratio, which is very desirable for an actuator. However, the design process is quite complex and time consuming due to many parameters. In this paper, we adapted the popular Taguchi method, widely used in manufacturing, to the problem of designing a complex MR-brake. Unlike other existing methods, this approach can automatically identify the dominant parameters of the design, which reduces the search space and the time it takes to find the best possible design. While automating the search for a solution, it also lets the designer see the dominant parameters and make choices to investigate only their interactions with the design output. The new method was applied for re-designing MR-brakes. It reduced the design time from a week or two down to a few minutes. Also, usability experiments indicated significantly better brake designs by novice users

Modelling and multi objective optimization of LM13 aluminium alloy squeeze cast process parameters using taguchi and genetic algorithm

Directory of Open Access Journals (Sweden)

S. Vellingiri

2018-01-01

Full Text Available This present investigation deals with squeeze casting process in order to produce a component with good mechanical properties such as micro-hardness(VH, tensile strength(Rm, and density(ρ on LM13 by varying squeeze pressure(P, molten temperature(Tm and die temperature(Td. Taguchi experimental design L9 orthogonal array was used to determine the signal to noise ratio. The results specified that the squeeze pressure and die preheat temperature are the most influencing parameters for mechanical properties improvement. Genetic algorithm (GA has been applied to optimize the casting parameters that simultaneously maximize the responses.

Near Field and Far Field Effects in the Taguchi-Optimized Design of AN InP/GaAs-BASED Double Wafer-Fused Mqw Long-Wavelength Vertical-Cavity Surface-Emitting Laser

Science.gov (United States)

Menon, P. S.; Kandiah, K.; Mandeep, J. S.; Shaari, S.; Apte, P. R.

Long-wavelength VCSELs (LW-VCSEL) operating in the 1.55 μm wavelength regime offer the advantages of low dispersion and optical loss in fiber optic transmission systems which are crucial in increasing data transmission speed and reducing implementation cost of fiber-to-the-home (FTTH) access networks. LW-VCSELs are attractive light sources because they offer unique features such as low power consumption, narrow beam divergence and ease of fabrication for two-dimensional arrays. This paper compares the near field and far field effects of the numerically investigated LW-VCSEL for various design parameters of the device. The optical intensity profile far from the device surface, in the Fraunhofer region, is important for the optical coupling of the laser with other optical components. The near field pattern is obtained from the structure output whereas the far-field pattern is essentially a two-dimensional fast Fourier Transform (FFT) of the near-field pattern. Design parameters such as the number of wells in the multi-quantum-well (MQW) region, the thickness of the MQW and the effect of using Taguchi's orthogonal array method to optimize the device design parameters on the near/far field patterns are evaluated in this paper. We have successfully increased the peak lasing power from an initial 4.84 mW to 12.38 mW at a bias voltage of 2 V and optical wavelength of 1.55 μm using Taguchi's orthogonal array. As a result of the Taguchi optimization and fine tuning, the device threshold current is found to increase along with a slight decrease in the modulation speed due to increased device widths.

Thermal property testing technique on micro specimen

International Nuclear Information System (INIS)

Baba, Tetsuya; Kishimoto, Isao; Taketoshi, Naoyuki

2000-01-01

This study aims at establishment of further development on some testing techniques on the nuclear advanced basic research accumulated by the National Research Laboratory of Metrology for ten years. For this purpose, a technology to test heat diffusion ratio and specific heat capacity of less than 3 mm in diameter and 1 mm in thickness of micro specimen and technology to test heat diffusion ratio at micro area of less than 1 mm in area along cross section of less than 10 mm in diameter of column specimen were developed to contribute to common basic technology supporting the nuclear power field. As a result, as an element technology to test heat diffusion ratio and specific heat capacity of the micro specimen, a specimen holding technique stably to hold a micro specimen with 3 mm in diameter could be developed. And, for testing the specific heat capacity by using the laser flush differential calorimetry, a technique to hold two specimen of 5 mm in diameter at their proximities was also developed. In addition, by promoting development of thermal property data base capable of storing thermal property data obtained in this study and with excellent workability in this 1998 fiscal year a data in/out-put program with graphical user interface could be prepared. (G.K.)

Ultrasonic creeping wave test technique for dissimilar metal weld

International Nuclear Information System (INIS)

Yuan Jianzhong; Shang Junmin; Yan Zhi; Yuan Guanghua; Zhang Guofeng

2009-01-01

To solve the problem encountered in the defect inspection of the surface and near-surface of dissimilar metal weld effectively, a new ultrasonic creeping wave test technique is developed. In this paper, the test technique and its experimental verification are mainly described. The verification results show that linear defect, which is similar to the defect found in liquid penetrant test, on the surface and near-surface of dissimilar metal weld can be detected effectively, by using ultrasonic creeping wave test technique. And the depth, length and height of the defect can be determined easily. The effective covering depth of ultrasonic creeping wave test technique will reach 0-9 mm. Meanwhile, the planar defect, with equivalent area more than 3 mm 2 , existed in welds can be detected efficiently. So, accurate measurement, which self height dimension of planar defect is above 2 mm, will be realized. (authors)

Optimization and scale-up of fermentation of glucansucrase and branched glucan by Pediococcus pentosaceus CRAG3 using Taguchi methodology in bioreactor

Directory of Open Access Journals (Sweden)

RISHIKESH SHUKLA

2012-01-01

Full Text Available The present investigation focuses on screening and optimization of media components to enhance glucansucrase and glucan production by Pediococcus pentosaceus CRAG3 at shake-flask and bioreactor level using Taguchi orthogonal array design. A three-level Taguchi orthogonal array layout of L27 (33 was employed, in which six variables were studied for their influence on glucansucrase and glucan production. The results showed that sucrose, K2HPO4 and Tween-80 were the most significant factors to improve glucansucrase production while the glucan production was mostly affected by sucrose, peptone and K2HPO4. The optimized medium composition for maximum glucansucrase and glucan production were: sucrose 3.5% and 5%; yeast extract 0.2% and 2.0%; beef extract 0.5% and 0.5%; peptone 3.0% and 1.0%; K2HPO4 0.2% and 0.2%, and Tween-80 1.0 and 0.1%, respectively. The optimized medium gave 10.1 U/ml and 10.2 U/ml glucansucrase activity while glucan concentrations were 56 mg/ml and 80 mg/ml in shake flask and bioreactor level, respectively which were in good agreement with predicted values (10.1 U/ml and 54.5 mg/ml. The optimized medium gave 2 fold enhancement in enzyme activity and 4 fold increase in glucan concentration as compared to non-optimized medium (4.5 U/ml and 15 mg/ml, respectively at shake flask level.

Ninja hacking unconventional penetration testing tactics and techniques

CERN Document Server

Wilhelm, Thomas

2010-01-01

Ever thought of using the time-tested tactics and techniques of the ancient ninja to understand the mind of today's ninja, the hacker? As a penetration tester or security consultant you no doubt perform tests both externally and internally for your clients that include both physical and technical tests. Throw traditional pen testing methods out the window for now and see how thinking and acting like a ninja can actually grant you quicker and more complete access to a company's assets. Get in before the hacker does with these unorthodox techniques. Use all of the tools that the ninja has: di

Multi response optimization of wire-EDM process parameters of ballistic grade aluminium alloy

Directory of Open Access Journals (Sweden)

Ravindranadh Bobbili

2015-12-01

Full Text Available In the current investigation, a multi response optimization technique based on Taguchi method coupled with Grey relational analysis is planned for wire-EDM operations on ballistic grade aluminium alloy for armour applications. Experiments have been performed with four machining variables: pulse-on time, pulse-off time, peak current and spark voltage. Experimentation has been planned as per Taguchi technique. Three performance characteristics namely material removal rate (MRR, surface roughness (SR and gap current (GC have been chosen for this study. Results showed that pulse-on time, peak current and spark voltage were significant variables to Grey relational grade. Variation of performance measures with process variables was modelled by using response surface method. The confirmation tests have also been performed to validate the results obtained by Grey relational analysis and found that great improvement with 6% error is achieved.

Radio Ranging Techniques to test Relativistic Gravitation

OpenAIRE

Cowsik, R.

1999-01-01

It is suggested that modern techniques of radio ranging when applied to study the motion of the Moon, can improve the accuracy of tests of relativistic gravitation obtained with currently operating laser ranging techniques. Other auxillary information relevant to the Solar system would also emerge from such a study.

Design of Maternity Pillow by Using Kansei and Taguchi Methods

Science.gov (United States)

Ilma Rahmillah, Fety; Nanda kartika, Rachmah

2017-06-01

One of the customers’ considerations for purchasing a product is it can satisfy their feeling and emotion. It because of such product can enhance sleep quality of pregnant women. However, most of the existing product such as maternity pillows are still designed based on companies’ perspective. This study aims to capture the desire of pregnant women toward maternity pillow desired product by using kansei words and analyze the optimal design with Taguchi method. Eight collected kansei words were durable, aesthetic, comfort, portable, simple, multifunction, attractive motive, and easy to maintain. While L16 orthogonal array is used because there are three variables with two levels and four variables with four levels. It can be concluded that the best maternity pillow that can satisfy the customers can be designed by combining D1-E2-F2-G2-C1-B2-A2 means the model is U shape, flowery motive, medium color, Bag model B, cotton pillow cover, filled with silicon, and use double zipper. However, it is also possible to create combination of D1-E2-F2-G2-C1-B1-A1 by using consideration of cost which means that the zipper is switched to single as well as filled with dacron. In addition, the total percentage of contribution by using ANOVA reaches 95%.

Optimization of machining techniques – A retrospective and ...

Indian Academy of Sciences (India)

tool designs because these are hidden under computerized databases in proprietary software ... ting speed and feed rate to yield minimum production cost. .... Quality is designed, not manufactured, into the product (Daetz 1987; Taguchi.

Dating technique tested

International Nuclear Information System (INIS)

Anon.

1985-01-01

An analytical technique for dating ground water and polar ice up to a million years old has been successfully tested by scientists at Oak Ridge National Laboratory (ORNL). The system, known as a rare gas atom counter, extends the capabilities of resonance ionization mass spectrometry to include counting single atoms of krypton-81. The counter is composed of a pulsed dye laser operated in tandem with a mass spectrometer to separate the various isotopes of krypton. In a collaborative study, ORNL scientists recently used the method for the first time to count krypton-81 in a liter of ground water removed from a sandstone aquifer near Zurich. Fewer than 1000 krypton-81 atoms were isolated from the ground water samples. According to Bernard Lehman, a collaborating geochemist at the University of Bern, this first test proved that counting the small numbers of krypton-81 atoms necessary to make an estimate of the age of water could actually be done. Among the applications of this method, Lehman says, could be improved siting of locations for the disposal of radioactive wastes

An Experimental Investigation into the Optimal Processing Conditions for the CO2 Laser Cladding of 20 MnCr5 Steel Using Taguchi Method and ANN

Science.gov (United States)

Mondal, Subrata; Bandyopadhyay, Asish.; Pal, Pradip Kumar

2010-10-01

This paper presents the prediction and evaluation of laser clad profile formed by means of CO2 laser applying Taguchi method and the artificial neural network (ANN). Laser cladding is one of the surface modifying technologies in which the desired surface characteristics of any component can be achieved such as good corrosion resistance, wear resistance and hardness etc. Laser is used as a heat source to melt the anti-corrosive powder of Inconel-625 (Super Alloy) to give a coating on 20 MnCr5 substrate. The parametric study of this technique is also attempted here. The data obtained from experiments have been used to develop the linear regression equation and then to develop the neural network model. Moreover, the data obtained from regression equations have also been used as supporting data to train the neural network. The artificial neural network (ANN) is used to establish the relationship between the input/output parameters of the process. The established ANN model is then indirectly integrated with the optimization technique. It has been seen that the developed neural network model shows a good degree of approximation with experimental data. In order to obtain the combination of process parameters such as laser power, scan speed and powder feed rate for which the output parameters become optimum, the experimental data have been used to develop the response surfaces.

FPGA based mixed-signal circuit novel testing techniques

International Nuclear Information System (INIS)

Pouros, Sotirios; Vassios, Vassilios; Papakostas, Dimitrios; Hristov, Valentin

2013-01-01

Electronic circuits fault detection techniques, especially on modern mixed-signal circuits, are evolved and customized around the world to meet the industry needs. The paper presents techniques used on fault detection in mixed signal circuits. Moreover, the paper involves standardized methods, along with current innovations for external testing like Design for Testability (DfT) and Built In Self Test (BIST) systems. Finally, the research team introduces a circuit implementation scheme using FPGA

Application of entropy measurement technique in grey based ...

African Journals Online (AJOL)

For this study, four control variables are selected current, voltage, gas flow rate and ... Keywords: Metal Inert Gas (MIG) Welding, Grey-Taguchi Method, Entropy ...... of metal inert gas welding on the corrosion and mechanical behaviour of.

Pie technique of LWR fuel cladding fracture toughness test

International Nuclear Information System (INIS)

Endo, Shinya; Usami, Koji; Nakata, Masahito; Fukuda, Takuji; Numata, Masami; Kizaki, Minoru; Nishino, Yasuharu

2006-01-01

Remote-handling techniques were developed by cooperative research between the Department of Hot Laboratories in the Japan Atomic Energy Research Institute (JAERI) and the Nuclear Fuel Industries Ltd. (NFI) for evaluating the fracture toughness on irradiated LWR fuel cladding. The developed techniques, sample machining by using the electrical discharge machine (EDM), pre-cracking by fatigue tester, sample assembling to the compact tension (CT) shaped test fixture gave a satisfied result for a fracture toughness test developed by NFL. And post-irradiation examination (PIE) using the remote-handling techniques were carried out to evaluate the fracture toughness on BWR spent fuel cladding in the Waste Safety Testing Facility (WASTEF). (author)

Contribution of phased array technique to automation in ultrasonic testing

International Nuclear Information System (INIS)

Erhard, A.; Schenk, G.; Moehrle, W.; Wuestenberg, H.; Rathgeb, W.

1989-01-01

Ultrasonic tests on complicated geometries often require expensive manipulator technique. To guarantee certain information from tests, the control of the manipulator must be matched to the acoustic boundary conditions. In the past and today, complex manipulators were and are being developed and used with tests on such geometries. The results of the measurements with group radiator technique in the bottom hole area or on ducts, showed that the manipulators can be simplified, particularly with regard to their degrees of freedom, e.g.: doing without the axis of rotation to set the angle of squint in testing ducts, without thereby narrowing the test area. In the bottom hole test, it was found that by using the group radiator technique, the test area is expanded, evaluation is simplified and coupling can be ensured. (orig.) [de

Ultrasonic testing technique for users in practical application. Pt. 8

International Nuclear Information System (INIS)

Corsepius, H.W.

1978-01-01

In the present, eighth part of ultrasonic testing technique for users in practical application, the two methods 1) testing by gap coupling and 2) testing by the dipping technique are treated. By the first method the probe is clamped in a holding device in such manner that a water-filled gap remains between probe and surface. Through this gap the sonic signal gets into the specimen without mechanical contact between probe and specimen taking place. By the dipping technique testing is performed in a tank filled with water, the probe being guided over the specimen under water. (RW) [de

Natural language processing techniques for automatic test ...

African Journals Online (AJOL)

Natural language processing techniques for automatic test questions generation using discourse connectives. ... PROMOTING ACCESS TO AFRICAN RESEARCH. AFRICAN JOURNALS ... Journal of Computer Science and Its Application.

A Method to Test Model Calibration Techniques: Preprint

Energy Technology Data Exchange (ETDEWEB)

Judkoff, Ron; Polly, Ben; Neymark, Joel

2016-09-01

This paper describes a method for testing model calibration techniques. Calibration is commonly used in conjunction with energy retrofit audit models. An audit is conducted to gather information about the building needed to assemble an input file for a building energy modeling tool. A calibration technique is used to reconcile model predictions with utility data, and then the 'calibrated model' is used to predict energy savings from a variety of retrofit measures and combinations thereof. Current standards and guidelines such as BPI-2400 and ASHRAE-14 set criteria for 'goodness of fit' and assume that if the criteria are met, then the calibration technique is acceptable. While it is logical to use the actual performance data of the building to tune the model, it is not certain that a good fit will result in a model that better predicts post-retrofit energy savings. Therefore, the basic idea here is that the simulation program (intended for use with the calibration technique) is used to generate surrogate utility bill data and retrofit energy savings data against which the calibration technique can be tested. This provides three figures of merit for testing a calibration technique, 1) accuracy of the post-retrofit energy savings prediction, 2) closure on the 'true' input parameter values, and 3) goodness of fit to the utility bill data. The paper will also discuss the pros and cons of using this synthetic surrogate data approach versus trying to use real data sets of actual buildings.

An analysis to optimize the process parameters of friction stir welded ...

African Journals Online (AJOL)

The friction stir welding (FSW) of steel is a challenging task. Experiments are conducted here, with a tool having a conical pin of 0.4mm clearance. The process parameters are optimized by using the Taguchi technique based on Taguchi's L9 orthogonal array. Experiments have been conducted based on three process ...

Experimental wear behavioral studies of as-cast and 5 hr homogenized Al25Mg2Si2Cu4Ni alloy at constant load based on taguchi method

Science.gov (United States)

Harlapur, M. D.; Mallapur, D. G.; Udupa, K. Rajendra

2018-04-01

In the present study, an experimental study of the volumetric wear behaviour of Aluminium (Al-25Mg2Si2Cu4Ni) alloy in as cast and 5Hr homogenized with T6 heat treatment is carried out at constant load. The Pin on disc apparatus was used to carry out the sliding wear test. Taguchi method based on L-16 orthogonal array was employed to evaluate the data on the wear behavior. Signal-to-noise ratio among the objective of smaller the better and mean of means results were used. General regression model is obtained by correlation. Lastly confirmation test was completed to compose a comparison between the experimental results foreseen from the mention correlation. The mathematical model reveals the load has maximum contribution on the wear rate compared to speed. Scanning Electron Microscope was used to analyze the worn-out wear surfaces. Wear results show that 5Hr homogenized Al-25Mg2Si2Cu4Ni alloy samples with T6 treated had better volumetric wear resistance as compared to as cast samples.

Ultrasonic testing using time of flight diffraction technique (TOFD)

International Nuclear Information System (INIS)

Khurram Shahzad; Ahmad Mirza Safeer Ahmad; Muhammad Asif Khan

2009-04-01

This paper describes the ultrasonic testing using Time Flight Diffraction (TOFD) Technique for welded samples having different types and sizes of defects. TOFD is a computerized ultrasonic system, able to scan, store and evaluate indications in terms of location, through thickness and length in a more easy and convenient. Time of Flight Diffraction Technique (TOFD) is more fast and easy technique for ultrasonic testing as we can examine a weld i a single scan along the length of the weld with two probes known as D-scan. It shows the image of the complete weld with the defect information. The examinations were performed on carbon steel samples used for ultrasonic testing using 70 degree probes. The images for different type of defects were obtained. (author)

Combining structural-thermal coupled field FE analysis and the Taguchi method to evaluate the relative contributions of multi-factors in a premolar adhesive MOD restoration.

Science.gov (United States)

Lin, Chun-Li; Chang, Yen-Hsiang; Lin, Yi-Feng

2008-08-01

The aim of this study was to determine the relative contribution of changes in restorative material, cavity dimensions, adhesive layer adaptation, and load conditions on the biomechanical response of an adhesive Class II MOD restoration during oral temperature changes. A validated finite-element (FE) model was used to perform the structural-thermal coupled field analyses and the Taguchi method was employed to identify the significance of each design factor in controlling the stress. The results indicated that thermal expansion in restorative material amplified the thermal effect and dominated the tooth stress value (69%) at high temperatures. The percentage contributions of the load conditions, cavity depth, and cement modulus increased the effect on tooth stress values 46%, 32%, and 14%, respectively, when the tooth temperature was returned to 37 degrees C. Load conditions were also the main factor influencing the resin cement stress values, irrespective of temperature changes. Increased stress values occurred with composite resin, lateral force, a deeper cavity, and a higher luting cement modulus. The combined use of FE analysis and the Taguchi method efficiently identified that a deeper cavity might increase the risk of a restored tooth fracture, as well as a ceramic inlay with a lower thermal expansion, attaining a proper occlusal adjustment to reduce the lateral occlusal force and low modulus luting material application to obtain a better force-transmission mechanism are recommended.

Improved Nanomechanical Test Techniques for Surface Engineered Materials

Directory of Open Access Journals (Sweden)

Stephen R. Goodes

2010-06-01

Full Text Available The development and implementation of a wide range of innovative nanomechanical test techniques to solve tribological problems in applications as diverse as biomedical and automotive are described in this review. For improved wear resistance and durability, the importance of understanding the system response rather than the coating-only properties is emphasized. There are many applications involving mechanical contact where the key to understanding the problem is to test at higher load and to combine reliable measurements taken across different length scales using both nano- and micro-indentation and related wear measurement techniques which more closely simulate contact conditions to fully understand the mechanical behaviour and hence deliver improved application performance. Results are presented with the NanoTest platform for applications for biomedical devices and surface engineering of lightweight alloys for the automotive industry. By combining results with different techniques it is possible to postulate predictive design rules – based on the elastic and plastic deformation energies involved in contact - to aid the reliable optimisation of mechanical properties in the various contact situations in the different applications.

Performance of Ti-multilayer coated tool during machining of MDN431 alloyed steel

Science.gov (United States)

Badiger, Pradeep V.; Desai, Vijay; Ramesh, M. R.

2018-04-01

Turbine forgings and other components are required to be high resistance to corrosion and oxidation because which they are highly alloyed with Ni and Cr. Midhani manufactures one of such material MDN431. It's a hard-to-machine steel with high hardness and strength. PVD coated insert provide an answer to problem with its state of art technique on the WC tool. Machinability studies is carried out on MDN431 steel using uncoated and Ti-multilayer coated WC tool insert using Taguchi optimisation technique. During the present investigation, speed (398-625rpm), feed (0.093-0.175mm/rev), and depth of cut (0.2-0.4mm) varied according to Taguchi L9 orthogonal array, subsequently cutting forces and surface roughness (Ra) were measured. Optimizations of the obtained results are done using Taguchi technique for cutting forces and surface roughness. Using Taguchi technique linear fit model regression analysis carried out for the combination of each input variable. Experimented results are compared and found the developed model is adequate which supported by proof trials. Speed, feed and depth of cut are linearly dependent on the cutting force and surface roughness for uncoated insert whereas Speed and depth of cut feed is inversely dependent in coated insert for both cutting force and surface roughness. Machined surface for coated and uncoated inserts during machining of MDN431 is studied using optical profilometer.

NDE Techniques Used in PARENT Open Round Robin Testing

Energy Technology Data Exchange (ETDEWEB)

Meyer, Ryan M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2014-11-05

This is a draft technical letter report for NRC client describing the NDE techniques used in the open testing portion of the Program to Assess the Reliability of Emerging Nondestructive Techniques (PARENT).

Digital circuit testing a guide to DFT and other techniques

CERN Document Server

Wong, Francis C

1991-01-01

Recent technological advances have created a testing crisis in the electronics industry--smaller, more highly integrated electronic circuits and new packaging techniques make it increasingly difficult to physically access test nodes. New testing methods are needed for the next generation of electronic equipment and a great deal of emphasis is being placed on the development of these methods. Some of the techniques now becoming popular include design for testability (DFT), built-in self-test (BIST), and automatic test vector generation (ATVG). This book will provide a practical introduction to

Imaging techniques for ultrasonic testing

International Nuclear Information System (INIS)

2013-01-01

These seminar proceedings contain 16 lectures on the following topics: 1. From imaging to quantification - ultrasound methods in medical diagnostics; 2. SAFT, TOFD, Phased Array - classical applications and recent developments in ultrasonic imaging; 3. Innovative ultrasonic imaging methods in research and application; 4. Industrial ultrasonic testing of fibre-reinforced structures of complex geometry; 5. Visualisation of crack tips in the inspection of wheel set shafts with longitudinal boreholes as a means of avoiding unnecessary wheel set changes; 6. Areal analysis of the propagation of Lamb waves on curved, anisotropic structures; 7. High-resolution representation in immersion technique testing; 8. Variants in generating images from phased array measurement data - practical examples involving copper, carbon-fibre reinforced plastic and other materials; 9. GIUM - an unconventional method of microstructure imaging using ultrasonic stimulation and laser vibrometry scanning; 10. Innovative air-ultrasonic testing concepts for improved imaging; 11. Use of imaging methods for improving the quality of test results from nondestructive testing; 12. Modelling and visualisation of EMUS stimulation for transducer optimisation; 13. Use of SAFT in the manufacture of energy conversion machines; 14. Ultrasonic imaging tests for improved defect characterisation during weld seam inspection on longitudinally welded large-diameter pipes; 15. SAFT reconstruction for testing austenitic weld seams and dissimilar metal weld seams for transverse cracks; 16. Imaging-based optimisation method for quantitative ultrasonic testing of anisotropic inhomogeneous austenitic welded joints with determination and utilisation of their elastic properties. One contribution has been abstracted separately. [de

Flank wear analysing of high speed end milling for hardened steel D2 using Taguchi Method

Science.gov (United States)

Hazza Faizi Al-Hazza, Muataz; Ibrahim, Nur Asmawiyah bt; Adesta, Erry T. Y.; Khan, Ahsan Ali; Abdullah Sidek, Atiah Bt.

2017-03-01

One of the main challenges for any manufacturer is how to decrease the machining cost without affecting the final quality of the product. One of the new advanced machining processes in industry is the high speed hard end milling process that merges three advanced machining processes: high speed milling, hard milling and dry milling. However, one of the most important challenges in this process is to control the flank wear rate. Therefore a analyzing the flank wear rate during machining should be investigated in order to determine the best cutting levels that will not affect the final quality of the product. In this research Taguchi method has been used to investigate the effect of cutting speed, feed rate and depth of cut and determine the best level s to minimize the flank wear rate up to total length of 0.3mm based on the ISO standard to maintain the finishing requirements.

Selection of Near Optimal Laser Cutting Parameters in CO2 Laser Cutting by the Taguchi Method

Directory of Open Access Journals (Sweden)

Miloš MADIĆ

2013-12-01

Full Text Available Identification of laser cutting conditions that are insensitive to parameter variations and noise is of great importance. This paper demonstrates the application of Taguchi method for optimization of surface roughness in CO2 laser cutting of stainless steel. The laser cutting experiment was planned and conducted according to the Taguchi’s experimental design using the L27 orthogonal array. Four laser cutting parameters such as laser power, cutting speed, assist gas pressure, and focus position were considered in the experiment. Using the analysis of means and analysis of variance, the significant laser cutting parameters were identified, and subsequently the optimal combination of laser cutting parameter levels was determined. The results showed that the cutting speed is the most significant parameter affecting the surface roughness whereas the influence of the assist gas pressure can be neglected. It was observed, however, that interaction effects have predominant influence over the main effects on the surface roughness.

Direct comparison of unloading compliance and potential drop techniques in J-integral testing

International Nuclear Information System (INIS)

McGowan, J.J.; Nanstad, R.K.

1984-01-01

Single-specimen J-integral testing is performed commonly with the unloading compliance technique. Use of modern instrumentation techniques and powerful desktop computers have made this technique a standard. However, this testing technique is slow and tedious, with the loading rate fixed at a slow quasi-static rate. For these reasons the dc potential drop technique was investigated for crack length measurement during a J-integral test. For direct comparison, both unloading compliance and potential drop were used simultaneously during a J-integral test. The results showed good agreement between the techniques. However, the potential drop technique showed an offset in crack length due to plastic blunting processes. Taking this offset into account, J/sub Ic/ values calculated by both techniques compared well

Specificity and sensitivity assessment of selected nasal provocation testing techniques

Directory of Open Access Journals (Sweden)

Edyta Krzych-Fałta

2016-12-01

Full Text Available Introduction: Nasal provocation testing involves an allergen-specific local reaction of the nasal mucosa to the administered allergen. Aim: To determine the most objective nasal occlusion assessment technique that could be used in nasal provocation testing. Material and methods : A total of 60 subjects, including 30 patients diagnosed with allergy to common environmental allergens and 30 healthy subjects were enrolled into the study. The method used in the study was a nasal provocation test with an allergen, with a standard dose of a control solution and an allergen (5,000 SBU/ml administered using a calibrated atomizer into both nostrils at room temperature. Early-phase nasal mucosa response in the early phase of the allergic reaction was assessed via acoustic rhinometry, optical rhinometry, nitric oxide in nasal air, and tryptase levels in the nasal lavage fluid. Results : In estimating the homogeneity of the average values, the Levene’s test was used and receiver operating characteristic curves were plotted for all the methods used for assessing the nasal provocation test with an allergen. Statistically significant results were defined for p < 0.05. Of all the objective assessment techniques, the most sensitive and characteristic ones were the optical rhinometry techniques (specificity = 1, sensitivity = 1, AUC = 1, PPV = 1, NPV = 1. Conclusions : The techniques used showed significant differences between the group of patients with allergic rhinitis and the control group. Of all the objective assessment techniques, those most sensitive and characteristic were the optical rhinometry.

Accelerated Testing Methodology in Constant Stress-Rate Testing for Advanced Structural Ceramics: A Preloading Technique

Science.gov (United States)

Choi, Sung R.; Gyekenyesi, John P.; Huebert, Dean; Bartlett, Allen; Choi, Han-Ho

2001-01-01

Preloading technique was used as a means of an accelerated testing methodology in constant stress-rate (dynamic fatigue) testing for two different brittle materials. The theory developed previously for fatigue strength as a function of preload was further verified through extensive constant stress-rate testing for glass-ceramic and CRT glass in room temperature distilled water. The preloading technique was also used in this study to identify the prevailing failure mechanisms at elevated temperatures, particularly at lower test rates in which a series of mechanisms would be associated simultaneously with material failure, resulting in significant strength increase or decrease. Two different advanced ceramics including SiC whisker-reinforced composite silicon nitride and 96 wt% alumina were used at elevated temperatures. It was found that the preloading technique can be used as an additional tool to pinpoint the dominant failure mechanism that is associated with such a phenomenon of considerable strength increase or decrease.

Experimental investigation of radiation effect on human thermal comfort by Taguchi method

International Nuclear Information System (INIS)

Arslanoglu, Nurullah; Yigit, Abdulvahap

2016-01-01

Highlights: • Radiation heat flux from lighting lamps on human thermal comfort is studied. • The effect of posture position on thermal comfort is investigated. • The effect of clothing color on thermal comfort is examined. • Radiation heat flux from halogen reflector lamp increase skin temperature more. • Posture position effect on thermal comfort is less than the other parameters. - Abstract: In this study, the effect of radiation heat flux of lighting lamps on human thermal comfort was investigated by using Taguchi method. In addition, at indoor conditions, clothing color and posture position under the radiation effect on thermal comfort were also investigated. For this purpose, experiments were performed in an air conditioned laboratory room in summer and autumn seasons. The amount of temperature rise on the back was considered as performance parameter. An L8 orthogonal array was selected as an experimental plan for the third parameters mentioned above for summer and autumn seasons. The results were analyzed for the optimum conditions using signal-to-noise (S/N) ratio and ANOVA method. The optimum results were found to be clear halogen lamp as lighting lamp, white as t-shirt color, standing as posture position, in summer season. The optimum levels of the lighting lamp, t-shirt color and posture position were found to be clear halogen lamp, white, sitting in autumn season, respectively.

Applying modern psychometric techniques to melodic discrimination testing: Item response theory, computerised adaptive testing, and automatic item generation.

Science.gov (United States)

Harrison, Peter M C; Collins, Tom; Müllensiefen, Daniel

2017-06-15

Modern psychometric theory provides many useful tools for ability testing, such as item response theory, computerised adaptive testing, and automatic item generation. However, these techniques have yet to be integrated into mainstream psychological practice. This is unfortunate, because modern psychometric techniques can bring many benefits, including sophisticated reliability measures, improved construct validity, avoidance of exposure effects, and improved efficiency. In the present research we therefore use these techniques to develop a new test of a well-studied psychological capacity: melodic discrimination, the ability to detect differences between melodies. We calibrate and validate this test in a series of studies. Studies 1 and 2 respectively calibrate and validate an initial test version, while Studies 3 and 4 calibrate and validate an updated test version incorporating additional easy items. The results support the new test's viability, with evidence for strong reliability and construct validity. We discuss how these modern psychometric techniques may also be profitably applied to other areas of music psychology and psychological science in general.

Wear Evaluation of AISI 4140 Alloy Steel with WC/C Lamellar Coatings Sliding Against EN 8 Using Taguchi Method

Science.gov (United States)

Kadam, Nikhil Rajendra; Karthikeyan, Ganesarethinam

2016-10-01

The purpose of the experiments in this paper is to use the Taguchi methods to investigate the wear of WC/C coated nitrided AISI 4140 alloy steel. A study of lamellar WC/C coating which were deposited by a physical vapor deposition on nitrided AISI 4140 alloy steel. The investigation includes wear evaluation using Pin-on-disk configuration. When WC/C coated AISI 4140 alloy steel slides against EN 8 steel, it was found that carbon-rich coatings show much lower wear of the countersurface than nitrogen-rich coatings. The results were correlated with the properties determined from tribological and mechanical characterization, therefore by probably selecting the proper processing parameters the deposition of WC/C coating results in decreasing the wear rate of the substrate which shows a potential for tribological application.

Costing improvement of remanufacturing crankshaft by integrating Mahalanobis-Taguchi System and Activity based Costing

Science.gov (United States)

Abu, M. Y.; Nor, E. E. Mohd; Rahman, M. S. Abd

2018-04-01

Integration between quality and costing system is very crucial in order to achieve an accurate product cost and profit. Current practice by most of remanufacturers, there are still lacking on optimization during the remanufacturing process which contributed to incorrect variables consideration to the costing system. Meanwhile, traditional costing accounting being practice has distortion in the cost unit which lead to inaccurate cost of product. The aim of this work is to identify the critical and non-critical variables during remanufacturing process using Mahalanobis-Taguchi System and simultaneously estimate the cost using Activity Based Costing method. The orthogonal array was applied to indicate the contribution of variables in the factorial effect graph and the critical variables were considered with overhead costs that are actually demanding the activities. This work improved the quality inspection together with costing system to produce an accurate profitability information. As a result, the cost per unit of remanufactured crankshaft of MAN engine model with 5 critical crankpins is MYR609.50 while Detroit engine model with 4 critical crankpins is MYR1254.80. The significant of output demonstrated through promoting green by reducing re-melting process of damaged parts to ensure consistent benefit of return cores.

Testing techniques in nuclear, petroleum and metallurgic industries

International Nuclear Information System (INIS)

Anon.

1977-01-01

The nondestructive testing techniques by ultrasonic waves, eddy currents, acoustic emission used by Intercontrole (a CEA's affiliated firm in nuclear petrochemical, and engineering site measurements) are presented [fr

Multidisciplinary Design Techniques Applied to Conceptual Aerospace Vehicle Design. Ph.D. Thesis Final Technical Report

Science.gov (United States)

Olds, John Robert; Walberg, Gerald D.

1993-01-01

Multidisciplinary design optimization (MDO) is an emerging discipline within aerospace engineering. Its goal is to bring structure and efficiency to the complex design process associated with advanced aerospace launch vehicles. Aerospace vehicles generally require input from a variety of traditional aerospace disciplines - aerodynamics, structures, performance, etc. As such, traditional optimization methods cannot always be applied. Several multidisciplinary techniques and methods were proposed as potentially applicable to this class of design problem. Among the candidate options are calculus-based (or gradient-based) optimization schemes and parametric schemes based on design of experiments theory. A brief overview of several applicable multidisciplinary design optimization methods is included. Methods from the calculus-based class and the parametric class are reviewed, but the research application reported focuses on methods from the parametric class. A vehicle of current interest was chosen as a test application for this research. The rocket-based combined-cycle (RBCC) single-stage-to-orbit (SSTO) launch vehicle combines elements of rocket and airbreathing propulsion in an attempt to produce an attractive option for launching medium sized payloads into low earth orbit. The RBCC SSTO presents a particularly difficult problem for traditional one-variable-at-a-time optimization methods because of the lack of an adequate experience base and the highly coupled nature of the design variables. MDO, however, with it's structured approach to design, is well suited to this problem. The result of the application of Taguchi methods, central composite designs, and response surface methods to the design optimization of the RBCC SSTO are presented. Attention is given to the aspect of Taguchi methods that attempts to locate a 'robust' design - that is, a design that is least sensitive to uncontrollable influences on the design. Near-optimum minimum dry weight solutions are

Test plan for suitability assessment of five overcoring stress measurement techniques

International Nuclear Information System (INIS)

Gregory, E.C.; Rundle, T.A.; McCabe, W.M.; Kim, K.

1982-08-01

Tests are to be conducted at the Near-Surface Test Facility (NSTF) to assess the suitability of five overcoring techniques for in situ stress determination in a jointed basalt. The overcoring methods to be investigated use the following instrumentation to measure strain relief by overcoring a pilot borehole: USBM borehole deformation gage, CSIRO hollow inclusion stress cell, cast epoxy inclusion, the Lulea triaxial strain cell and the ''doorstopper'' biaxial strain cell. The tests are to provide data regarding the state of stress below the NSTF. This information is to be used in the evaluation of each method of overcoring. During the course of field testing, an attempt is to be made to adapt conventional overcoring techniques and analytical methods to the basalt medium. If overcoring stress determination in basalt is shown suitable, then additional studies will be identified to further adapt a technique for use at depth. In addition to the five overcoring techniques to be tested at the NSTF, stress measurements by Hydrofracturing are to be conducted to provide data for direct comparison with overcoring results. 16 refs., 18 figs

Experimental investigation of urea injection parameters influence on NOx emissions from blended biodiesel-fueled diesel engines.

Science.gov (United States)

Mehregan, Mina; Moghiman, Mohammad

2018-02-01

The present work submits an investigation about the effect of urea injection parameters on NO x emissions from a four-stroke four-cylinder diesel engine fueled with B20 blended biodiesel. An L 9 (3 4 ) Taguchi orthogonal array was used to design the test plan. The results reveal that increasing urea concentration leads to lower NO x emissions. Urea flow rate increment has the same influence on NO x emission. The same result is obtained by an increase in spray angle. Also, according to the analysis of variance (ANOVA), urea concentration and then urea flow rate are the most effective design parameters on NO x emissions, while spray angle and mixing length have less influence on this pollutant emission. Finally, since the result of confirmation test is in good agreement with the predicted value based on the Taguchi technique, the predictive capability of this method in the present study could be deduced.

Technique for unit testing of safety software verification and validation

International Nuclear Information System (INIS)

Li Duo; Zhang Liangju; Feng Junting

2008-01-01

The key issue arising from digitalization of the reactor protection system for nuclear power plant is how to carry out verification and validation (V and V), to demonstrate and confirm the software that performs reactor safety functions is safe and reliable. One of the most important processes for software V and V is unit testing, which verifies and validates the software coding based on concept design for consistency, correctness and completeness during software development. The paper shows a preliminary study on the technique for unit testing of safety software V and V, focusing on such aspects as how to confirm test completeness, how to establish test platform, how to develop test cases and how to carry out unit testing. The technique discussed here was successfully used in the work of unit testing on safety software of a digital reactor protection system. (authors)

The Study of an Integrated Rating System for Supplier Quality Performance in the Semiconductor Industry

Science.gov (United States)

Lee, Yu-Cheng; Yen, Tieh-Min; Tsai, Chih-Hung

This study provides an integrated model of Supplier Quality Performance Assesment (SQPA) activity for the semiconductor industry through introducing the ISO 9001 management framework, Importance-Performance Analysis (IPA) Supplier Quality Performance Assesment and Taguchi`s Signal-to-Noise Ratio (S/N) techniques. This integrated model provides a SQPA methodology to create value for all members under mutual cooperation and trust in the supply chain. This method helps organizations build a complete SQPA framework, linking organizational objectives and SQPA activities to optimize rating techniques to promote supplier quality improvement. The techniques used in SQPA activities are easily understood. A case involving a design house is illustrated to show our model.

Twitch interpolation technique in testing of maximal muscle strength

DEFF Research Database (Denmark)

Bülow, P M; Nørregaard, J; Danneskiold-Samsøe, B

1993-01-01

The aim was to study the methodological aspects of the muscle twitch interpolation technique in estimating the maximal force of contraction in the quadriceps muscle utilizing commercial muscle testing equipment. Six healthy subjects participated in seven sets of experiments testing the effects...

Alternative containment integrity test methods, an overview of possible techniques

International Nuclear Information System (INIS)

Spletzer, B.L.

1986-01-01

A study is being conducted to develop and analyze alternative methods for testing of containment integrity. The study is focused on techniques for continuously monitoring containment integrity to provide rapid detection of existing leaks, thus providing greater certainty of the integrity of the containment at any time. The study is also intended to develop techniques applicable to the currently required Type A integrated leakage rate tests. A brief discussion of the range of alternative methods currently being considered is presented. The methods include applicability to all major containment types, operating and shutdown plant conditions, and quantitative and qualitative leakage measurements. The techniques are analyzed in accordance with the current state of knowledge of each method. The bulk of the techniques discussed are in the conceptual stage, have not been tested in actual plant conditions, and are presented here as a possible future direction for evaluating containment integrity. Of the methods considered, no single method provides optimum performance for all containment types. Several methods are limited in the types of containment for which they are applicable. The results of the study to date indicate that techniques for continuous monitoring of containment integrity exist for many plants and may be implemented at modest cost

Development of a liquid filter testing technique using radioisotope

International Nuclear Information System (INIS)

Kumar, Surender; Ramarathinam, K.; Khan, A.A.

1979-01-01

Efficient removal of suspended matter from liquids was always in demand in industries as a process requirement for the recovery of suspended materials. In nuclear industry the filters are required to remove fine suspended matter from water in reactors, effluent treatment plants, fuel reprocessing plants etc. The filters are used to maintain clarity and to limit the activity level to a minimum. In effluent treatment plants low level liquid waste is discharged to the environment after removing active suspended matter by filters. Various type of liquid filters are available in the market to meet the demands of different industries. These filters must be evaluated for their removal effectiveness for particulate matter from liquids. The filters are evaluated using several techniques like gravimetric analysis, turbidity measurement, direct counting of particles using optical and electronic instruments etc. All the techniques have their own advantages and disadvantages. Counting of radioactive particles using radiation counters is a simple and sensitive technique. It involves the neutron activation of selected test powders which are dispersed in the liquid and led through the test filter; the up-stream and down-stream concentrations are measured using GM counter. This technique was found to be consistent and reproducible in the low, middle and high ranges of efficiency. Selection of a test powder, its activation and use for evaluating liquid filters are dealt with. (auth.)

Automated Testing Techniques for Event-Driven and Dynamically Typed Software Applications

DEFF Research Database (Denmark)

Adamsen, Christoffer Quist

techniques to address each of the challenges. We present a new methodology that extends the error detection capabilities of existing, manually written Android test suites. In the context of JavaScript web applications, we present practical race detectors for detecting AJAX and initialization races......, and a technique that can prevent event race errors by restricting the nondeterminism. Finally, we present a notion of test completeness for dynamic languages, along with a hybrid static/dynamic analysis framework that approximates test completeness, and demonstrate the usefulness of test completeness facts...

Laccase production by Coriolopsis caperata RCK2011: Optimization under solid state fermentation by Taguchi DOE methodology

Science.gov (United States)

Nandal, Preeti; Ravella, Sreenivas Rao; Kuhad, Ramesh Chander

2013-01-01

Laccase production by Coriolopsis caperata RCK2011 under solid state fermentation was optimized following Taguchi design of experiment. An orthogonal array layout of L18 (21 × 37) was constructed using Qualitek-4 software with eight most influensive factors on laccase production. At individual level pH contributed higher influence, whereas, corn steep liquor (CSL) accounted for more than 50% of the severity index with biotin and KH2PO4 at the interactive level. The optimum conditions derived were; temperature 30°C, pH 5.0, wheat bran 5.0 g, inoculum size 0.5 ml (fungal cell mass = 0.015 g dry wt.), biotin 0.5% w/v, KH2PO4 0.013% w/v, CSL 0.1% v/v and 0.5 mM xylidine as an inducer. The validation experiments using optimized conditions confirmed an improvement in enzyme production by 58.01%. The laccase production to the level of 1623.55 Ugds−1 indicates that the fungus C. caperata RCK2011 has the commercial potential for laccase. PMID:23463372

New Technique for Cryogenically Cooling Small Test Articles

Science.gov (United States)

Rodriquez, Karen M.; Henderson, Donald J.

2011-01-01

Convective heat removal techniques to rapidly cool small test articles to Earth-Moon L2 temperatures of 77 K were accomplished through the use of liquid nitrogen (LN2). By maintaining a selected pressure range on the saturation curve, test articles were cooled below the LN2 boiling point at ambient pressure in less than 30 min. Difficulties in achieving test pressures while maintaining the temperature tolerance necessitated a modification to the original system to include a closed loop conductive cold plate and cryogenic shroud

SSSFD manipulator engineering using statistical experiment design techniques

Science.gov (United States)

Barnes, John

1991-01-01

The Satellite Servicer System Flight Demonstration (SSSFD) program is a series of Shuttle flights designed to verify major on-orbit satellite servicing capabilities, such as rendezvous and docking of free flyers, Orbital Replacement Unit (ORU) exchange, and fluid transfer. A major part of this system is the manipulator system that will perform the ORU exchange. The manipulator must possess adequate toolplate dexterity to maneuver a variety of EVA-type tools into position to interface with ORU fasteners, connectors, latches, and handles on the satellite, and to move workpieces and ORUs through 6 degree of freedom (dof) space from the Target Vehicle (TV) to the Support Module (SM) and back. Two cost efficient tools were combined to perform a study of robot manipulator design parameters. These tools are graphical computer simulations and Taguchi Design of Experiment methods. Using a graphics platform, an off-the-shelf robot simulation software package, and an experiment designed with Taguchi's approach, the sensitivities of various manipulator kinematic design parameters to performance characteristics are determined with minimal cost.

Integration of Mahalanobis-Taguchi system and traditional cost accounting for remanufacturing crankshaft

Science.gov (United States)

Abu, M. Y.; Norizan, N. S.; Rahman, M. S. Abd

2018-04-01

Remanufacturing is a sustainability strategic planning which transforming the end of life product to as new performance with their warranty is same or better than the original product. In order to quantify the advantages of this strategy, all the processes must implement the optimization to reach the ultimate goal and reduce the waste generated. The aim of this work is to evaluate the criticality of parameters on the end of life crankshaft based on Taguchi’s orthogonal array. Then, estimate the cost using traditional cost accounting by considering the critical parameters. By implementing the optimization, the remanufacturer obviously produced lower cost and waste during production with higher potential to gain the profit. Mahalanobis-Taguchi System was proven as a powerful method of optimization that revealed the criticality of parameters. When subjected the method to the MAN engine model, there was 5 out of 6 crankpins were critical which need for grinding process while no changes happened to the Caterpillar engine model. Meanwhile, the cost per unit for MAN engine model was changed from MYR1401.29 to RM1251.29 while for Caterpillar engine model have no changes due to the no changes on criticality of parameters consideration. Therefore, by integrating the optimization and costing through remanufacturing process, a better decision can be achieved after observing the potential profit will be gained. The significant of output demonstrated through promoting sustainability by reducing re-melting process of damaged parts to ensure consistent benefit of return cores.

Wide Panel Testing Technique for Evaluating Repair Weld Strengths

Science.gov (United States)

Rogers, Patrick R.; Bynum, Julian E.; Shah, Sandeep R.

1998-01-01

This paper describes a new tensile testing technique for evaluating the overall effect of a repair weld on the strength of a welded joint. Previously, repair weld strengths have been evaluated using one-inch width tensile specimens, but this technique does not capture all of the effects that result from a repair. The new technique involves testing of "wide panel" tensile specimens which contain the full length of a repair weld within a longer initial weld, allowing the specimen to capture the combined effects of residual stresses, local strength degradation, and load redistribution around a repair. The development of strains in the repair area of standard aluminum alloy specimens and new high-performance aluminum-lithium alloy specimens was observed and evaluated using photoelastic material. The results of this evaluation show an increased sensitivity to repair welding residual stresses in the aluminum-lithium alloy specimens.

Biosorption of malachite green from aqueous solutions by Pleurotus ostreatus using Taguchi method

Science.gov (United States)

2014-01-01

Dyes released into the environment have been posing a serious threat to natural ecosystems and aquatic life due to presence of heat, light, chemical and other exposures stable. In this study, the Pleurotus ostreatus (a macro-fungus) was used as a new biosorbent to study the biosorption of hazardous malachite green (MG) from aqueous solutions. The effective disposal of P. ostreatus is a meaningful work for environmental protection and maximum utilization of agricultural residues. The operational parameters such as biosorbent dose, pH, and ionic strength were investigated in a series of batch studies at 25°C. Freundlich isotherm model was described well for the biosorption equilibrium data. The biosorption process followed the pseudo-second-order kinetic model. Taguchi method was used to simplify the experimental number for determining the significance of factors and the optimum levels of experimental factors for MG biosorption. Biosorbent dose and initial MG concentration had significant influences on the percent removal and biosorption capacity. The highest percent removal reached 89.58% and the largest biosorption capacity reached 32.33 mg/g. The Fourier transform infrared spectroscopy (FTIR) showed that the functional groups such as, carboxyl, hydroxyl, amino and phosphonate groups on the biosorbent surface could be the potential adsorption sites for MG biosorption. P. ostreatus can be considered as an alternative biosorbent for the removal of dyes from aqueous solutions. PMID:24620852

Test/score/report: Simulation techniques for automating the test process

Science.gov (United States)

Hageman, Barbara H.; Sigman, Clayton B.; Koslosky, John T.

1994-01-01

A Test/Score/Report capability is currently being developed for the Transportable Payload Operations Control Center (TPOCC) Advanced Spacecraft Simulator (TASS) system which will automate testing of the Goddard Space Flight Center (GSFC) Payload Operations Control Center (POCC) and Mission Operations Center (MOC) software in three areas: telemetry decommutation, spacecraft command processing, and spacecraft memory load and dump processing. Automated computer control of the acceptance test process is one of the primary goals of a test team. With the proper simulation tools and user interface, the task of acceptance testing, regression testing, and repeatability of specific test procedures of a ground data system can be a simpler task. Ideally, the goal for complete automation would be to plug the operational deliverable into the simulator, press the start button, execute the test procedure, accumulate and analyze the data, score the results, and report the results to the test team along with a go/no recommendation to the test team. In practice, this may not be possible because of inadequate test tools, pressures of schedules, limited resources, etc. Most tests are accomplished using a certain degree of automation and test procedures that are labor intensive. This paper discusses some simulation techniques that can improve the automation of the test process. The TASS system tests the POCC/MOC software and provides a score based on the test results. The TASS system displays statistics on the success of the POCC/MOC system processing in each of the three areas as well as event messages pertaining to the Test/Score/Report processing. The TASS system also provides formatted reports documenting each step performed during the tests and the results of each step. A prototype of the Test/Score/Report capability is available and currently being used to test some POCC/MOC software deliveries. When this capability is fully operational it should greatly reduce the time necessary

Rotor Pole Shape Optimization of Permanent Magnet Brushless DC Motors Using the Reduced Basis Technique

Directory of Open Access Journals (Sweden)

GHOLAMIAN, A. S.

2009-06-01

Full Text Available In this paper, a magnet shape optimization method for reduction of cogging torque and torque ripple in Permanent Magnet (PM brushless DC motors is presented by using the reduced basis technique coupled by finite element and design of experiments methods. The primary objective of the method is to reduce the enormous number of design variables required to define the magnet shape. The reduced basis technique is a weighted combination of several basis shapes. The aim of the method is to find the best combination using the weights for each shape as the design variables. A multi-level design process is developed to find suitable basis shapes or trial shapes at each level that can be used in the reduced basis technique. Each level is treated as a separated optimization problem until the required objective is achieved. The experimental design of Taguchi method is used to build the approximation model and to perform optimization. This method is demonstrated on the magnet shape optimization of a 6-poles/18-slots PM BLDC motor.

Optimization of critical factors to enhance polyhydroxyalkanoates (PHA) synthesis by mixed culture using Taguchi design of experimental methodology.

Science.gov (United States)

Venkata Mohan, S; Venkateswar Reddy, M

2013-01-01

Optimizing different factors is crucial for enhancement of mixed culture bioplastics (polyhydroxyalkanoates (PHA)) production. Design of experimental (DOE) methodology using Taguchi orthogonal array (OA) was applied to evaluate the influence and specific function of eight important factors (iron, glucose concentration, VFA concentration, VFA composition, nitrogen concentration, phosphorous concentration, pH, and microenvironment) on the bioplastics production. Three levels of factor (2(1) × 3(7)) variation were considered with symbolic arrays of experimental matrix [L(18)-18 experimental trails]. All the factors were assigned with three levels except iron concentration (2(1)). Among all the factors, microenvironment influenced bioplastics production substantially (contributing 81%), followed by pH (11%) and glucose concentration (2.5%). Validation experiments were performed with the obtained optimum conditions which resulted in improved PHA production. Good substrate degradation (as COD) of 68% was registered during PHA production. Dehydrogenase and phosphatase enzymatic activities were monitored during process operation. Copyright © 2012 Elsevier Ltd. All rights reserved.

A hybrid Taguchi-artificial neural network approach to predict surface roughness during electric discharge machining of titanium alloys

Energy Technology Data Exchange (ETDEWEB)

Kumar, Sanjeev; Batish, Ajay [Thapar University, Patiala (India); Singh, Rupinder [GNDEC, Ludhiana (India); Singh, T. P. [Symbiosis Institute of Technology, Pune (India)

2014-07-15

In the present study, electric discharge machining process was used for machining of titanium alloys. Eight process parameters were varied during the process. Experimental results showed that current and pulse-on-time significantly affected the performance characteristics. Artificial neural network coupled with Taguchi approach was applied for optimization and prediction of surface roughness. The experimental results and the predicted results showed good agreement. SEM was used to investigate the surface integrity. Analysis for migration of different chemical elements and formation of compounds on the surface was performed using EDS and XRD pattern. The results showed that high discharge energy caused surface defects such as cracks, craters, thick recast layer, micro pores, pin holes, residual stresses and debris. Also, migration of chemical elements both from electrode and dielectric media were observed during EDS analysis. Presence of carbon was seen on the machined surface. XRD results showed formation of titanium carbide compound which precipitated on the machined surface.

Testing philosophy and simulation techniques

International Nuclear Information System (INIS)

Holtbecker, H.

1977-01-01

This paper reviews past and present testing philosophies and simulation techniques in the field of structure loading and response studies. The main objective of experimental programmes in the past was to simulate a hypothetical energy release with explosives and to deduce the potential damage to a reactor from the measured damage to the model. This approach was continuously refined by improving the instrumentation of the models, by reproducing the structures as faithful as possible and by developing new explosive charges. This paper presents an analysis of the factors which are expected to have an influence on the validity of the results e.g. strain rate effects and the use of water instead of sodium. More recently the discussion of a whole series of accidents in the probabilistic accident analysis and the intention to compare different reactor designs has revealed the need to develop and validate computer codes. Consequently experimental programmes have been started in which the primary aim is not to test a specific reactor but to validate codes. This paper shows the principal aspects of this approach and discusses first results. (Auth.)

Study of Nd:YAG laser annealing of electroless Ni-P film on spiegel-iron plate by Taguchi method and grey system theory

Energy Technology Data Exchange (ETDEWEB)

Liu, W.L. [Department of Materials Science and Engineering, National Formosa University, 64, Wunhua Road, Huwei, Yunlin 632, Taiwan (China); Chien, W.T.; Jiang, M.H. [Department of Mechanical Engineering, National Pingtung University of Science and Technology, 1, Shuehfu Road, Neipu, Pingtung 912, Taiwan (China); Chen, W.J., E-mail: chenwjau@yuntech.edu.t [Graduate School of Materials Science, National Yunlin University of Science and Technology, 123 University Road, Section 3, Douliou, Yunlin 64002, Taiwan (China)

2010-04-09

An electroless Ni-P film was first deposited on a spiegel-iron plate and then annealed by an Nd:YAG pulsed wave laser. In order to obtain the optimal laser annealing parameters for maximizing the hardness and minimizing the surface roughness of electroless Ni-P films, the Taguchi method and grey system theory were used to analyze the experimental data. The electroless Ni-P film was also characterized by scanning electron microscopy for the morphology, and transmission electron microscopy for the microstructure and crystal structure. The results showed that the hardness and the surface roughness of electroless Ni-P films can be, at the same time, improved to 50.8% and 68%, respectively, by the laser annealing with the optimal parameters.

Study of Nd:YAG laser annealing of electroless Ni-P film on spiegel-iron plate by Taguchi method and grey system theory

International Nuclear Information System (INIS)

Liu, W.L.; Chien, W.T.; Jiang, M.H.; Chen, W.J.

2010-01-01

An electroless Ni-P film was first deposited on a spiegel-iron plate and then annealed by an Nd:YAG pulsed wave laser. In order to obtain the optimal laser annealing parameters for maximizing the hardness and minimizing the surface roughness of electroless Ni-P films, the Taguchi method and grey system theory were used to analyze the experimental data. The electroless Ni-P film was also characterized by scanning electron microscopy for the morphology, and transmission electron microscopy for the microstructure and crystal structure. The results showed that the hardness and the surface roughness of electroless Ni-P films can be, at the same time, improved to 50.8% and 68%, respectively, by the laser annealing with the optimal parameters.

Low-Power Built-In Self-Test Techniques for Embedded SRAMs

Directory of Open Access Journals (Sweden)

Shyue-Kung Lu

2007-01-01

Full Text Available The severity of power consumption during parallel BIST of embedded memory cores is growing significantly. In order to alleviate this problem, a row bank-based precharge technique based on the divided wordline (DWL architecture is proposed for low-power testing of embedded SRAMs. The memory cell array is first divided into row banks. The effectiveness of the row bank-based precharge technique is due to the predictable address sequence during test. In low-power test mode, instead of precharging the entire memory array, only the current accessed row bank is precharged. This will result in significant power saving for the precharge circuitry. The precharge power can be reduced to 1/b of that of the traditional precharge techniques, where b denotes the number of row banks in the memory array. With simple transmission gates and inverters, the modified precharge control circuitry was also designed. The hardware overhead for implementing the low-power technique is almost negligible. Moreover, the corresponding BIST design to implement the low-power technique is almost the same as the conventional BIST designs. It is also notable that the inherent low-power characteristics of the DWL architecture can be preserved. According to experimental results, 48.9% power reduction can be achieved for a 256 × 256 bit-oriented SRAM. The memory is divided into 8 row banks. Moreover, if the number of row banks increases, the power saving will also increase.

LHC Magnet Tests Operational Techniques and Empowerment for Successful Completion

CERN Document Server

Chohan, V; Priestnall, K; Pirotte, F; Veyrunes, E; Ali, N; Awale, P; Bahuguna, S; Bhunia, U; Chauhan, V; Dixit, M; Gore, J; John, J; Kandaswamy, E; Kasbekar, A; Kashyap, P; Kasliwal, A; Kulkarni, C; Laddha, A; Malhotra, S; Mascarenhas, M; Mishra, J; Motiwala, P; Nair, K; Narayanan, R; Padmakumar, S; Pagare, A; Peruppayikkad, D; Raghunathan, S; Rao, S; Roy, D; Sharma, S; Shimjith, S; Singh, S; Sonnis, S; Sridhar, S; Surendran, P; Tikaria, A

2007-01-01

The LHC magnet tests operation team developed various innovative techniques, particularly since early 2004, to complete the superconductor magnet tests by Feb. 2007. Overall and cryogenic priority handling, rapid on-bench thermal cycling, rule-based goodness evaluation on round-the-clock basis, multiple, mashed web systems are some of these techniques applied with rigour for successful tests completion in time. This paper highlights these operation empowerment tools which had a pivotal role for success. A priority handling method was put in place to enable maximum throughput from twelve test benches, having many different constraints. For the cryogenics infrastructure, it implied judicious allocation of limited resources to the benches. Rapid On-Bench Thermal Cycle was a key strategy to accelerate magnets tests throughput, saving time and simplifying logistics. First level magnet appraisal was developed for 24 hr decision making so as to prepare a magnet further for LHC or keep it on standby. Web based system...

KAJIAN KUAT BENDING DAN KADAR AIR PADA KOMPOSIT DARI SEKAM PADI DAN SERAT BAMBU MENGGUNAKAN STATISTIK TAGUCHI

Directory of Open Access Journals (Sweden)

Joko Yunianto Prihatin

2017-11-01

Full Text Available Kayu merupakan komoditi utama dalam pembuatan mebel yang berasal dari alam. Dewasa ini penyusutan  hutan  dunia  telah  mengkhawatirkan mencapai  80%.  Sehingga  kebutuhan  oksigen  akan menurun karena tidak sesuai dengan upaya reboisasi. Disisi lain bambu memiliki kelebihan dalam hal masa panen yang lebih cepat berkisar 2–3 tahun. Sedangkan sekam padi adalah limbah yang dihasilkan dari kegiatan pengolahan hasil pertanian yang pemanfaatannya selama ini hanya sebagai bahan pembantu dalam aktifitas produksi, maka nilai ekonomis sekam padi ini sangat rendah. Berdasarkan permasalahan diatas, maka penelitian ini dititik beratkan pada pembuatan komposit anyaman bambu dan sekam padi sebagai pengganti kayu dalam industri mebel. Penelitian ini menggunakan desain eksperimen statistik taguchi, sehingga meghasilkan nilai kuat bending optimal 35,58N/mm2 dengan kadar air 0,334%. Kondisi optimal tersebut terdiri dari A3B2C2D1 Variasi anyaman Satin, Tekanan hidrolik 60N, Waktu pemanasan sebelum pengecoran pada suhu 105oC adalah 45 menit, dan Komposisi = Resin 100 : Katalis 0,75.

Vacuum leak test technique of JT-60

International Nuclear Information System (INIS)

Kaminaga, Atsushi; Arai, Takashi; Kodama, Kozo; Sasaki, Noboru; Saidoh, Masahiro

1998-01-01

Since a vacuum vessel of JT-60 is very large (167 m 3 ) and is combined with many components, such as magnetic coils, neutral beam injection systems and RF heating systems, etc., the position of leak testing exceeds 700. The two kind of techniques for vacuum leak test used in JT-60 has been described. Firstly the probe helium gas can be fed remotely in the three-dimensionally sectioned 54 regions of the JT-60 torus. The leak test was very rapidly performed by using this method. Secondly the helium detector system has been modified by the additional installation of the cryopump, which reduced the background level of the deuterium gas. The sensitivity of vacuum leak test with the cryopump was two orders of magnitude larger than that of without it. The examples of the performed vacuum leak test are stated. The vacuum leaks during experiments were 9 times. They were caused by thermal strain and plasma discharge. The vacuum leaks just after maintenance are 36 times which mainly caused by mis-installation. (author)

Taguchi Experimental Design for Optimization of Recombinant Human Growth Hormone Production in CHO Cell Lines and Comparing its Biological Activity with Prokaryotic Growth Hormone.

Science.gov (United States)

Aghili, Zahra Sadat; Zarkesh-Esfahani, Sayyed Hamid

2018-02-01

Growth hormone deficiency results in growth retardation in children and the GH deficiency syndrome in adults and they need to receive recombinant-GH in order to rectify the GH deficiency symptoms. Mammalian cells have become the favorite system for production of recombinant proteins for clinical application compared to prokaryotic systems because of their capability for appropriate protein folding, assembly, post-translational modification and proper signal. However, production level in mammalian cells is generally low compared to prokaryotic hosts. Taguchi has established orthogonal arrays to describe a large number of experimental situations mainly to reduce experimental errors and to enhance the efficiency and reproducibility of laboratory experiments.In the present study, rhGH was produced in CHO cells and production of rhGH was assessed using Dot blotting, western blotting and Elisa assay. For optimization of rhGH production in CHO cells using Taguchi method An M16 orthogonal experimental design was used to investigate four different culture components. The biological activity of rhGH was assessed using LHRE-TK-Luciferase reporter gene system in HEK-293 and compared to the biological activity of prokaryotic rhGH.A maximal productivity of rhGH was reached in the conditions of 1%DMSO, 1%glycerol, 25 µM ZnSO 4 and 0 mM NaBu. Our findings indicate that control of culture conditions such as the addition of chemical components helps to develop an efficient large-scale and industrial process for the production of rhGH in CHO cells. Results of bioassay indicated that rhGH produced by CHO cells is able to induce GH-mediated intracellular cell signaling and showed higher bioactivity when compared to prokaryotic GH at the same concentrations. © Georg Thieme Verlag KG Stuttgart · New York.

Sadhana | Indian Academy of Sciences

Indian Academy of Sciences (India)

... sequential unconstrained minimizationtechnique, dynamic programming etc. The latest techniques for optimization include fuzzy logic, scatter search technique, genetic algorithm, Taguchi technique and response surface methodology. Volume 31 Issue 6 December 2006 pp 671-681. Optimizing feed force for turned parts ...

Development of the transverse tensile and fracture toughness test techniques for spent fuel cladding

Energy Technology Data Exchange (ETDEWEB)

Ahn, S. B.; Hong, K. P.; Jung, Y. H.; Seo, H. S.; Oh, W. H.; Yoo, B. O.; Kim, D. S.; Seo, K. S

2001-12-01

To define the cause of cladding damage which can take place during the operation of nuclear power plant and the storage through the degradation aspect of mechanical characteristics, the transverse tensile an fracture toughness test were developed in hot cell at IMEF(Irradiated Material Experiment Facility). The following hot cell techniques were developed. 1. The development of a jig and a specimen for transverse tensile test 2. The acquisition of a manufacturing technique for the transverse tensile specimen at hot cell 3. The acquisition of testing procedures and an analysis technque for the transverse tensile 4. The dimensional determination of an optimized fracture toughness specimen 5. The acquisition of manufacturing technique for the fracture toughness test specimen at the hot cell 6. The acquisition of testing procedures and analysis technique for the fracture toughness test (Multiple specimen method, DCPD method, Load ratio method)

Supercritical CO2 extraction of candlenut oil: process optimization using Taguchi orthogonal array and physicochemical properties of the oil.

Science.gov (United States)

Subroto, Erna; Widjojokusumo, Edward; Veriansyah, Bambang; Tjandrawinata, Raymond R

2017-04-01

A series of experiments was conducted to determine optimum conditions for supercritical carbon dioxide extraction of candlenut oil. A Taguchi experimental design with L 9 orthogonal array (four factors in three levels) was employed to evaluate the effects of pressure of 25-35 MPa, temperature of 40-60 °C, CO 2 flow rate of 10-20 g/min and particle size of 0.3-0.8 mm on oil solubility. The obtained results showed that increase in particle size, pressure and temperature improved the oil solubility. The supercritical carbon dioxide extraction at optimized parameters resulted in oil yield extraction of 61.4% at solubility of 9.6 g oil/kg CO 2 . The obtained candlenut oil from supercritical carbon dioxide extraction has better oil quality than oil which was extracted by Soxhlet extraction using n-hexane. The oil contains high unsaturated oil (linoleic acid and linolenic acid), which have many beneficial effects on human health.

Experimental Investigation and Taguchi Optimisation of Drilling Properties on Teak Wood Reinforced Epoxy Resin

Science.gov (United States)

Lilly Mercy, J.; Shaqir Tanvir, Mohamed; Swaroopkanth, K.

2017-05-01

The drilling properties of teak reinforced epoxy resin composite are explored in this work. The thrust force and temperature during the drilling process was found and optimised. Nine holes were drilled in accordance with L9 orthogonal array on Medium Density Fibre board and Teak wood reinforced epoxy composite board and the thrust force and temperature induced during drilling is measured. Drilling experiments were conducted using CNC Vertical drilling machine and the thrust force was measured using dynamometer and temperature using infra-red thermometer. The experiments were conducted with varying levels of spindle speed and feed rate and optimised using Taguchi optimisation. It was observed that higher thrust and temperature were observed while drilling teak wood composite due to the high mechanical strength of teak wood. The hard and brittle properties of the resin seemed to be more pronounced in the composite. The experimental results were optimised to find the best combination of input parameters for reduced thrust and temperature. When speed increases, thrust force decreases and temperature increases. When feed increases, thrust force increases and temperature decreases. Experimental findings encouragesto use teak wood reinforced epoxy resin as a substitute for the traditionally used Medium Density Fibre Board. The percentage of mixing of teak dust can be increased with various resin combinations to arrive at the best suitable combination for obtaining optimal mechanical properties.

Large Field Photogrammetry Techniques in Aircraft and Spacecraft Impact Testing

Science.gov (United States)

Littell, Justin D.

2010-01-01

The Landing and Impact Research Facility (LandIR) at NASA Langley Research Center is a 240 ft. high A-frame structure which is used for full-scale crash testing of aircraft and rotorcraft vehicles. Because the LandIR provides a unique capability to introduce impact velocities in the forward and vertical directions, it is also serving as the facility for landing tests on full-scale and sub-scale Orion spacecraft mass simulators. Recently, a three-dimensional photogrammetry system was acquired to assist with the gathering of vehicle flight data before, throughout and after the impact. This data provides the basis for the post-test analysis and data reduction. Experimental setups for pendulum swing tests on vehicles having both forward and vertical velocities can extend to 50 x 50 x 50 foot cubes, while weather, vehicle geometry, and other constraints make each experimental setup unique to each test. This paper will discuss the specific calibration techniques for large fields of views, camera and lens selection, data processing, as well as best practice techniques learned from using the large field of view photogrammetry on a multitude of crash and landing test scenarios unique to the LandIR.

Bioremediation of chlorpyrifos contaminated soil by two phase bioslurry reactor: Processes evaluation and optimization by Taguchi's design of experimental (DOE) methodology.

Science.gov (United States)

Pant, Apourv; Rai, J P N

2018-04-15

Two phase bioreactor was constructed, designed and developed to evaluate the chlorpyrifos remediation. Six biotic and abiotic factors (substrate-loading rate, slurry phase pH, slurry phase dissolved oxygen (DO), soil water ratio, temperature and soil micro flora load) were evaluated by design of experimental (DOE) methodology employing Taguchi's orthogonal array (OA). The selected six factors were considered at two levels L-8 array (2^7, 15 experiments) in the experimental design. The optimum operating conditions obtained from the methodology showed enhanced chlorpyrifos degradation from 283.86µg/g to 955.364µg/g by overall 70.34% of enhancement. In the present study, with the help of few well defined experimental parameters a mathematical model was constructed to understand the complex bioremediation process and optimize the approximate parameters upto great accuracy. Copyright © 2017 Elsevier Inc. All rights reserved.

Measurement techniques and instruments suitable for life-prediction testing of photovoltaic arrays. Interim report

Energy Technology Data Exchange (ETDEWEB)

Noel, G.T.; Sliemers, F.A.; Deringer, G.C.; Wood, V.E.; Wilkes, K.E.; Gaines, G.B.; Carmichael, D.C.

1978-01-15

The validation of a service life of 20 years for low-cost photovoltaic arrays must be accomplished through accelerated life-prediction tests. A methodology for such tests has been developed in a preceding study. The results discussed consist of the initial identification and assessment of all known measurement techniques and instruments that might be used in these life-prediction tests. Array failure modes, relevant materials property changes, and primary degradation mechanisms are discussed as a prerequisite to identifying suitable measurement techniques and instruments. Candidate techniques and instruments are identified on the basis of extensive reviews of published and unpublished information. These methods are organized in six measurement categories--chemical, electrical, optical, thermal, mechanical, and ''other physicals''. Using specified evaluation criteria, the most promising techniques and instruments for use in life-prediction tests of arrays are then selected. These recommended techniques and their characteristics are described. Recommendations are made regarding establishment of the adequacy, particularly with respect to precision, of the more fully developed techniques for this application, and regarding the experimental evaluation of promising developmental techniques. Measurement needs not satisfied by presently available techniques/instruments are also identified.

Development for advanced materials and testing techniques

Energy Technology Data Exchange (ETDEWEB)

Hishinuma, Akimichi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1998-03-01

Recent studies using a JMTR and research reactors of JRR-2 and JRR-3 are briefly summarized. Small specimen testing techniques (SSTT) required for an effective use of irradiation volume and also irradiated specimens have been developed focussing on tensile test, fatigue test, Charpy test and small punch test. By using the small specimens of 0.1 - several mm in size, similar values of tensile and fatigue properties to those by standard size specimens can be taken, although the ductile-brittle transition temperature (DBTT) depends strongly on Charpy specimen size. As for advanced material development, R and D about low activation ferritic steels have been done to investigate irradiation response. The low activation ferritic steel, so-called F82H jointly-developed by JAERI and NKK for fusion, has been confirmed to have good irradiation resistance within a limited dose and now selected as a standard material in the fusion material community. It is also found that TiAi intermetallic compounds, which never been considered for nuclear application in the past, have an excellent irradiation resistance under an irradiation condition. Such knowledge can bring about a large expectation for developing advanced nuclear materials. (author)

Experimental Study on Abrasive Waterjet Polishing of Hydraulic Turbine Blades

International Nuclear Information System (INIS)

Khakpour, H; Birglenl, L; Tahan, A; Paquet, F

2014-01-01

In this paper, an experimental investigation is implemented on the abrasive waterjet polishing technique to evaluate its capability in polishing of surfaces and edges of hydraulic turbine blades. For this, the properties of this method are studied and the main parameters affecting its performance are determined. Then, an experimental test-rig is designed, manufactured and tested to be used in this study. This test-rig can be used to polish linear and planar areas on the surface of the desired workpieces. Considering the number of parameters and their levels, the Taguchi method is used to design the preliminary experiments. All experiments are then implemented according to the Taguchi L 18 orthogonal array. The signal-to-noise ratios obtained from the results of these experiments are used to determine the importance of the controlled polishing parameters on the final quality of the polished surface. The evaluations on these ratios reveal that the nozzle angle and the nozzle diameter have the most important impact on the results. The outcomes of these experiments can be used as a basis to design a more precise set of experiments in which the optimal values of each parameter can be estimated

Training guidelines in non-destructive testing techniques

International Nuclear Information System (INIS)

1991-10-01

Non-destructive testing methods (NDT), by their very nature, allow components to be fully examined for properties or flaws without interfering with their usefulness. This grouping of inspection methods has grown from a handful of primitive techniques practised by artists to a widely known discipline which is an essential part of quality control, largely as a result of the standards demanded by the nuclear and aerospace industries. Recognizing the need for an international publication of NDT training syllabi, the IAEA Consultants Meeting on ''Qualification and Certification of NDT Personnel'' (Milan, 20-21 May 1986), recommended that the Agency publish the guidelines developed by Regional Working Group of the Latin America and Caribbean project. It was first issued in English in 1987 and has now been re-edited in English and Spanish and enlarged by the addition of programmes for other techniques

Defect detection in conducting materials using eddy current testing techniques

Directory of Open Access Journals (Sweden)

Brauer Hartmut

2014-01-01

Full Text Available Lorentz force eddy current testing (LET is a novel nondestructive testing technique which can be applied preferably to the identification of internal defects in nonmagnetic moving conductors. The LET is compared (similar testing conditions with the classical eddy current testing (ECT. Numerical FEM simulations have been performed to analyze the measurements as well as the identification of internal defects in nonmagnetic conductors. The results are compared with measurements to test the feasibility of defect identification. Finally, the use of LET measurements to estimate of the electrical conductors under test are described as well.

Leak testing of bubble-tight dampers using tracer gas techniques

Energy Technology Data Exchange (ETDEWEB)

Lagus, P.L. [Lagus Applied Technology, Inc., San Diego, CA (United States); DuBois, L.J. [Commonwealth Edison, Zion, IL (United States); Fleming, K.M. [NCS Corporation, Columbus, OH (United States)] [and others

1995-02-01

Recently tracer gas techniques have been applied to the problem of measuring the leakage across an installed bubble-tight damper. A significant advantage of using a tracer gas technique is that quantitative leakage data are obtained under actual operating differential pressure conditions. Another advantage is that leakage data can be obtained using relatively simple test setups that utilize inexpensive materials without the need to tear ducts apart, fabricate expensive blank-off plates, and install test connections. Also, a tracer gas technique can be used to provide an accurate field evaluation of the performance of installed bubble-tight dampers on a periodic basis. Actual leakage flowrates were obtained at Zion Generating Station on four installed bubble-tight dampers using a tracer gas technique. Measured leakage rates ranged from 0.01 CFM to 21 CFM. After adjustment and subsequent retesting, the 21 CFM damper leakage was reduced to a leakage of 3.8 CFM. In light of the current regulatory climate and the interest in Control Room Habitability issues, imprecise estimates of critical air boundary leakage rates--such as through bubble-tight dampers--are not acceptable. These imprecise estimates can skew radioactive dose assessments as well as chemical contaminant exposure calculations. Using a tracer gas technique, the actual leakage rate can be determined. This knowledge eliminates a significant source of uncertainty in both radioactive dose and/or chemical exposure assessments.

Investigation and Taguchi Optimization of Microbial Fuel Cell Salt Bridge Dimensional Parameters

Science.gov (United States)

Sarma, Dhrupad; Barua, Parimal Bakul; Dey, Nabendu; Nath, Sumitro; Thakuria, Mrinmay; Mallick, Synthia

2018-01-01

One major problem of two chamber salt bridge microbial fuel cells (MFCs) is the high resistance offered by the salt bridge to anion flow. Many researchers who have studied and optimized various parameters related to salt bridge MFC, have not shed much light on the effect of salt bridge dimensional parameters on the MFC performance. Therefore, the main objective of this research is to investigate the effect of length and cross sectional area of salt bridge and the effect of solar radiation and atmospheric temperature on MFC current output. An experiment has been designed using Taguchi L9 orthogonal array, taking length and cross sectional area of salt bridge as factors having three levels. Nine MFCs were fabricated as per the nine trial conditions. Trials were conducted for 3 days and output current of each of the MFCs along with solar insolation and atmospheric temperature were recorded. Analysis of variance shows that salt bridge length has significant effect both on mean (with 53.90% contribution at 95% CL) and variance (with 56.46% contribution at 87% CL), whereas the effect of cross sectional area of the salt bridge and the interaction of these two factors is significant on mean only (with 95% CL). Optimum combination was found at 260 mm salt bridge length and 506.7 mm2 cross sectional area with 4.75 mA of mean output current. The temperature and solar insolation data when correlated with each of the MFCs average output current, revealed that both external factors have significant impact on MFC current output but the correlation coefficient varies from MFC to MFC depending on salt bridge dimensional parameters.

Optimisation of shock absorber process parameters using failure mode and effect analysis and genetic algorithm

Science.gov (United States)

Mariajayaprakash, Arokiasamy; Senthilvelan, Thiyagarajan; Vivekananthan, Krishnapillai Ponnambal

2013-07-01

The various process parameters affecting the quality characteristics of the shock absorber during the process were identified using the Ishikawa diagram and by failure mode and effect analysis. The identified process parameters are welding process parameters (squeeze, heat control, wheel speed, and air pressure), damper sealing process parameters (load, hydraulic pressure, air pressure, and fixture height), washing process parameters (total alkalinity, temperature, pH value of rinsing water, and timing), and painting process parameters (flowability, coating thickness, pointage, and temperature). In this paper, the process parameters, namely, painting and washing process parameters, are optimized by Taguchi method. Though the defects are reasonably minimized by Taguchi method, in order to achieve zero defects during the processes, genetic algorithm technique is applied on the optimized parameters obtained by Taguchi method.

Comparative testing of radiographic testing, ultrasonic testing and phased array advanced ultrasonic testing non destructive testing techniques in accordance with the AWS D1.5 bridge welding code.

Science.gov (United States)

2014-02-01

A comprehensive body of non-destructive testing data was collected from steel bridge welds under real-world conditions in a fabricators shop. Three different non-destructive testing (NDT) techniques were used on each weld inspection, these being R...

Optimization of de-esterified tragacanth microcapsules by computational fluid dynamic and the Taguchi design with purpose of the cell encapsulation.

Science.gov (United States)

Alvandimanesh, Azin; Sadrjavadi, Komail; Akbari, Mona; Fattahi, Ali

2017-12-01

This work presents the development of the new De-Esterified Tragacanth (DET) microcapsules (MCs). Co-flow extrusion method was applied for producing the MCs; the processing parameters were optimized by the Taguchi design to obtain the smallest and the most spherical MCs. Computational Fluid Dynamic (CFD) modeling was accomplished to show the formation of droplets at different airflows, and finally, βTC3 pancreatic cells were encapsulated in the MCs. The optimum MCs had 214.58μm size and 60.75% sphericality. The air pressure and the cross-linking reaction of DET were the most influential parameter in size and the sphericality of MCs, respectively. CFD showed two velocity vortices with rotational flow formed in the chamber, which caused changing the droplet moving direction. The encapsulated cells were proliferated, and cell viability was not reduced during six days. These phenomena make DET MCs a potential candidate for the cell encapsulation. Copyright © 2017 Elsevier B.V. All rights reserved.

Service Quality Robust Design by the Integration of Taguchi Experiments and SERVQUAL Approach in a Travel Agency

Directory of Open Access Journals (Sweden)

nassibeh janatyan

2012-02-01

Full Text Available The main purpose of this research is to address how robust design of service quality dimensions can be obtained. Service Quality Robust Design has been conducted by the integration of Taguchi Design of Experiments and SERVQUAL approach in Iran Travel Agency. Five basic dimensions of service quality, i.e. reliability, responsiveness, assurance, empathy, tangibles and price have been assumed as control factors. Response factor has been defined as two alternatives i the sum of customer expectations, and ii the sum of service quality gaps. In this investigation assumed that noise factor is not existed. The advantage of this paper is to improve the average and standard deviation simultaneously. Signal to noise ratio has been computed and the desired mix of the levels of service quality dimensions has been addressed. The main findings of this research includes the desired mix of the levels of service quality dimensions based on the sum of customer expectations and the desired mix of the levels of service quality dimensions based on the sum of service quality gaps. Comparing the two sets of findings helps the agency to analyze the cost of attracting new customers or retaining regular customers.

Optimisation of laser welding parameters for welding of P92 material using Taguchi based grey relational analysis

Directory of Open Access Journals (Sweden)

Shanmugarajan B.

2016-08-01

Full Text Available Creep strength enhanced ferritic (CSEF steels are used in advanced power plant systems for high temperature applications. P92 (Cr–W–Mo–V steel, classified under CSEF steels, is a candidate material for piping, tubing, etc., in ultra-super critical and advanced ultra-super critical boiler applications. In the present work, laser welding process has been optimised for P92 material by using Taguchi based grey relational analysis (GRA. Bead on plate (BOP trials were carried out using a 3.5 kW diffusion cooled slab CO2 laser by varying laser power, welding speed and focal position. The optimum parameters have been derived by considering the responses such as depth of penetration, weld width and heat affected zone (HAZ width. Analysis of variance (ANOVA has been used to analyse the effect of different parameters on the responses. Based on ANOVA, laser power of 3 kW, welding speed of 1 m/min and focal plane at −4 mm have evolved as optimised set of parameters. The responses of the optimised parameters obtained using the GRA have been verified experimentally and found to closely correlate with the predicted value.

OPTIMIZATION OF MACHINING PARAMETERS USING TAGUCHI APPROACH DURING HARD TURNING OF ALLOY STEEL WITH UNCOATED CARBIDE UNDER DRY CUTTING ENVIRONMENT

Directory of Open Access Journals (Sweden)

A. Das

2015-12-01

Full Text Available In today’s world of manufacturing by machining process two things are very important, one is productivity and the other one is quality. Quality of a product generally depends upon the surface finish and dimensional deviations. The productivity can be seen as a key economic indicator of innovation in terms of higher material removal rate with a less time and cost in machining industries. Taguchi method is a popular statistical technique for optimization of input parameters to get the best output results. Dry machining is a popular methodology for machining hard material and it has been accepted by many researchers to a great extent because of its low cost and safety. Many scientists have taken various input parameters and studied their effects on different output responses. In the present paper an attempt has been made to study the effect of input parameters such as cutting speed, feed rate and depth of cut on Surface roughness, Tool wear, Power consumption and Chip reduction co-efficient under dry condition using uncoated carbide insert. Signal to noise ratio has been used to select the optimal condition for various output responses. ANOVA table has been drawn for each output responses and finally mathematical model of multiple regression analysis has been prepared and authenticity of the statistical model have been checked by normal probability plot. It has been found from the experimental result that the power consumption and flank wear both were minimum at the cutting speed of 250 rpm and 400 rpm respectively. Chip reduction coefficient has been found minimum at a depth of cut of 0.3 mm and surface roughness was minimum at 0.1 mm/rev. feed rate.

Taguchi analysis of extrusion variables and composition effects on the morphology and mechanical properties of EPR-g-MA toughened polyamide 6 and its composite with short glass fiber

International Nuclear Information System (INIS)

Shojaei, A.; Fereydoon, M.

2009-01-01

Various compositions of maleated ethylene-propylene-rubber (EPR-g-MA) toughened polyamide 6 without and with short glass fiber, i.e. 5-20 wt.% rubber and 5-20 wt.% fiber, are prepared using an industrial twin-screw extruder at different levels of feed rate (100-250 kg/h), screw speed (200-450 rpm) and barrel temperature (230-260 deg. C). Trial runs designed based on the Taguchi's orthogonal arrays are subjected to tensile, impact, scanning electron microscopy (SEM) and optical microscopy tests; and the results are used to perform the analysis of variance (ANOVA). It is shown that the rubber particle size decreases significantly by increasing the rubber content for the unreinforced blend. The results also indicate that the composition of the compounds is the most influential factor on the phase morphology and mechanical properties of both the unreinforced and reinforced blends compared to the extrusion variables. But the processing parameters can also influence the performance characteristics slightly. The most important processing parameter, among the others, is shown to be the mixing temperature, which decreases the fiber length greatly and leads to the thermo-mechanical degradation of the polymers above 240 deg. C

The verification tests of residual radioactivity measurement and assessment techniques for buildings and soils

International Nuclear Information System (INIS)

Onozawa, T.; Ishikura, T.; Yoshimura, Yukio; Nakazawa, M.; Makino, S.; Urayama, K.; Kawasaki, S.

1996-01-01

According to the standard procedure for decommissioning a commercial nuclear power plant (CNPP) in Japan, controlled areas will be released for unrestricted use before the dismantling of a reactor building. If manual survey and sampling techniques were applied to measurement for unrestricted release on and in the extensive surface of the building, much time and much specialized labor would be required to assess the appropriateness of the releasing. Therefore the authors selected the following three techniques for demonstrating reliability and applicability of the techniques for CNPPs: (1) technique of assessing radioactive concentration distribution on the surface of buildings (ADB); (2) technique of assessing radioactive permeation distribution in the concrete structure of buildings (APB); (3) technique of assessing radioactive concentration distribution in soil (ADS). These tests include the techniques of measuring and assessing very low radioactive concentration distribution on the extensive surfaces of buildings and the soil surrounding of a plant with automatic devices. Technical investigation and preliminary study of the verification tests were started in 1990. In the study, preconditions were clarified for each technique and the performance requirements were set up. Moreover, simulation models have been constructed for several feasible measurement method to assess their performance in terms of both measurement test and simulation analysis. Fundamental tests have been under way using small-scale apparatuses since 1994

Optimization of Surface Finish in Turning Operation by Considering the Machine Tool Vibration using Taguchi Method

Directory of Open Access Journals (Sweden)

Muhammad Munawar

2012-01-01

Full Text Available Optimization of surface roughness has been one of the primary objectives in most of the machining operations. Poor control on the desired surface roughness generates non conforming parts and results into increase in cost and loss of productivity due to rework or scrap. Surface roughness value is a result of several process variables among which machine tool condition is one of the significant variables. In this study, experimentation was carried out to investigate the effect of machine tool condition on surface roughness. Variable used to represent machine tool\\'s condition was vibration amplitude. Input parameters used, besides vibration amplitude, were feed rate and insert nose radius. Cutting speed and depth of cut were kept constant. Based on Taguchi orthogonal array, a series of experimentation was designed and performed on AISI 1040 carbon steel bar at default and induced machine tool\\'s vibration amplitudes. ANOVA (Analysis of Variance, revealed that vibration amplitude and feed rate had moderate effect on the surface roughness and insert nose radius had the highest significant effect on the surface roughness. It was also found that a machine tool with low vibration amplitude produced better surface roughness. Insert with larger nose radius produced better surface roughness at low feed rate.

Optimization of Surface Roughness and Wall Thickness in Dieless Incremental Forming Of Aluminum Sheet Using Taguchi

Science.gov (United States)

Hamedon, Zamzuri; Kuang, Shea Cheng; Jaafar, Hasnulhadi; Azhari, Azmir

2018-03-01

Incremental sheet forming is a versatile sheet metal forming process where a sheet metal is formed into its final shape by a series of localized deformation without a specialised die. However, it still has many shortcomings that need to be overcome such as geometric accuracy, surface roughness, formability, forming speed, and so on. This project focus on minimising the surface roughness of aluminium sheet and improving its thickness uniformity in incremental sheet forming via optimisation of wall angle, feed rate, and step size. Besides, the effect of wall angle, feed rate, and step size to the surface roughness and thickness uniformity of aluminium sheet was investigated in this project. From the results, it was observed that surface roughness and thickness uniformity were inversely varied due to the formation of surface waviness. Increase in feed rate and decrease in step size will produce a lower surface roughness, while uniform thickness reduction was obtained by reducing the wall angle and step size. By using Taguchi analysis, the optimum parameters for minimum surface roughness and uniform thickness reduction of aluminium sheet were determined. The finding of this project helps to reduce the time in optimising the surface roughness and thickness uniformity in incremental sheet forming.

Technique for ultrasonic testing of austenitic steel weldments of NPP components

International Nuclear Information System (INIS)

Lantukh, V.M.; Grebennik, V.S.; Kordinov, E.V.; Kesler, N.A.; Shchedrin, I.F.

1987-01-01

Special literature on ultrasonic testing of weldments of austenitic steel is analysed. Technique for ultrasonic testing of the ring and longitudinal butt welded joints of NPP components without reinforcing bead removal is described. Special converter design and fabrication practice are described. Results of experimental check of the developed testing technology and its application during NNPs' mounting and operation are presented. Results of ultrasonic and X-ray testing are compared

Optimization of MR fluid Yield stress using Taguchi Method and Response Surface Methodology Techniques

Science.gov (United States)

Mangal, S. K.; Sharma, Vivek

2018-02-01

Magneto rheological fluids belong to a class of smart materials whose rheological characteristics such as yield stress, viscosity etc. changes in the presence of applied magnetic field. In this paper, optimization of MR fluid constituents is obtained with on-state yield stress as response parameter. For this, 18 samples of MR fluids are prepared using L-18 Orthogonal Array. These samples are experimentally tested on a developed & fabricated electromagnet setup. It has been found that the yield stress of MR fluid mainly depends on the volume fraction of the iron particles and type of carrier fluid used in it. The optimal combination of the input parameters for the fluid are found to be as Mineral oil with a volume percentage of 67%, iron powder of 300 mesh size with a volume percentage of 32%, oleic acid with a volume percentage of 0.5% and tetra-methyl-ammonium-hydroxide with a volume percentage of 0.7%. This optimal combination of input parameters has given the on-state yield stress as 48.197 kPa numerically. An experimental confirmation test on the optimized MR fluid sample has been then carried out and the response parameter thus obtained has found matching quite well (less than 1% error) with the numerically obtained values.

Surface crack testing - state of technique and trends in development

International Nuclear Information System (INIS)

1991-01-01

This Seminar contains 12 lectures on the following subjects: State of technique in magnetic powder testing (K. Goebbels); Recognisability of faults and probability of faults in surface crack testing (W. Morgner); Requirements for picture processing systems for proving and assessing crack indications (M. Stadthaus); Possibilities and limits of automatic crack recognition in magnetic powder testing (V. Deutsch); Development of equipment for eddy current testing (M. Junger); Signal processing - a way of improving the recognisability of faults in eddy current testing (R. Becker); Methods of testing steel products for surface faults and their practical limits of fault recognisability (D. Thiery); Surface crack testing in pipe manufacture (R. Pawelletz); Surface crack testing in powerstation construction (L. v. Bernus); Trends in automation in surface crack testing (G. Maier); Eddy current testing in engine construction (E. Dickhaut); Eddy current testing in aircraft repair (F. Schur). (orig.) [de

Flight Flutter Testing of Rotary Wing Aircraft Using a Control System Oscillation Technique

Science.gov (United States)

Yen, J. G.; Viswanathan, S.; Matthys, C. G.

1976-01-01

A flight flutter testing technique is described in which the rotor controls are oscillated by series actuators to excite the rotor and airframe modes of interest, which are then allowed to decay. The moving block technique is then used to determine the damped frequency and damping variation with rotor speed. The method proved useful for tracking the stability of relatively well damped modes. The results of recently completed flight tests of an experimental soft-in-plane rotor are used to illustrate the technique. Included is a discussion of the application of this technique to investigation of the propeller whirl flutter stability characteristics of the NASA/Army XV-15 VTOL tilt rotor research aircraft.

DSCu/SS joining techniques development and testing

International Nuclear Information System (INIS)

Sato, Satoshi; Hatano, Toshihisa; Furuya, Kazuyuki; Kuroda, Toshimasa; Enoeda, Mikio; Takatsu, Hideyuki

1998-01-01

Joining techniques of alumina dispersion strengthened copper alloy (DSCu) and type 316L stainless steel (SS) has been investigated aiming at applying to the fabrication of the ITER first wall/blanket. As the joining method, Hot Isostatic Pressing (HIP) of solid plates and/or blocks has been pursued. By a screening test including HIP temperatures of 980-1050degC, it was concluded that the HIP temperature of 1050degC would be optimum for the simultaneous HIPping of DSCu/DSCu, DSCu/SS and SS/SS. With DSCu/SS joint specimens HIPped at 1050degC, tensile, impact, fatigue, crack propagation, and fracture toughness tests were performed as well as mechanical test of structural model with one SS circular tube embedded. Typically, the properties of the joints were almost the same as those of DSCu or SS base metal with the same heat treatment of the HIP process, thus good joints were obtained, though parts of properties were decreased at elevated test temperature. Typical results of the mechanical test of structural mode indicated that a crack initiated at the inner surface of the SS tube under cyclic operation, and the lifetime of the first wall structure could be evaluated by existing SS fatigue data. Two HIPped first wall panel mock-ups were successfully fabricated with built-in coolant tubes: one was 300 mm long and the other 800 mm long. The former was thermo-mechanically tested with high heat fluxes corresponding to the ITER operation conditions. The mock-up showed good heat removal performance during the high heat flux tests. In addition, there were no cracks and delaminations found at HIPped interfaces by microscopic observation after all tests. Ultrasonic testing have been tried as a non-destructive examination method, and detectable defect size at SS/SS, DSCu/DSCu and DSCu/SS joint interfaces were estimated. (author)

Welding techniques development of CLAM steel for Test Blanket Module

Energy Technology Data Exchange (ETDEWEB)

Li Chunjing [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); School of Nuclear Science and Technology, University of Science and Technology of China, Hefei, Anhui, 230027 (China)], E-mail: lcj@ipp.ac.cn; Huang Qunying; Wu Qingsheng; Liu Shaojun [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); School of Nuclear Science and Technology, University of Science and Technology of China, Hefei, Anhui, 230027 (China); Lei Yucheng [Jiangsu University, Zhenjiang, Jiangsu, 212013 (China); Muroga, Takeo; Nagasaka, Takuya [National Institute for Fusion Science, Toki, Jifu, 509-5292 (Japan); Zhang Jianxun [Xi' an Jiaotong University, Xi' an, Shanxi, 710049 (China); Li Jinglong [Northwestern Polytechnical University, Xi' an, Shanxi, 710072 (China)

2009-06-15

Fabrication techniques for Test Blanket Module (TBM) with CLAM are being under development. Effect of surface preparation on the HIP diffusion bonding joints was studied and good joints with Charpy impact absorbed energy close to that of base metal have been obtained. The mechanical properties test showed that effect of HIP process on the mechanical properties of base metal was little. Uniaxial diffusion bonding experiments were carried out to study the effect of temperature on microstructure and mechanical properties. And preliminary experiments on Electron Beam Welding (EBW), Tungsten Inert Gas (TIG) Welding and Laser Beam Welding (LBW) were performed to find proper welding techniques to assemble the TBM. In addition, the thermal processes assessed with a Gleeble thermal-mechanical machine were carried out as well to assist the fusion welding research.

Advanced Marketing Core Curriculum. Test Items and Assessment Techniques.

Science.gov (United States)

Smith, Clifton L.; And Others

This document contains duties and tasks, multiple-choice test items, and other assessment techniques for Missouri's advanced marketing core curriculum. The core curriculum begins with a list of 13 suggested textbook resources. Next, nine duties with their associated tasks are given. Under each task appears one or more citations to appropriate…

Analysis of fresh fallout from Chinese tests by beta counting technique

International Nuclear Information System (INIS)

Mishra, U.C.; Lalit, B.Y.; Shukla, V.K.; Ramachandran, T.V.

1979-01-01

The paper describes beta counting techniques used in the analysis of fresh radioactive fallout samples from nuclear weapon tests. Fresh fallout samples have been collected by swiping the exposed portion of the engine covers of commercial aircrafts arriving at Bombay from New York after Chinese tests on September 26, 1976 and September 17, 1977. Activities of short-lived radionuclides such as Ag 111, Sr 89, Mo 99, U 237 and Np 239 were determined using these techniques. The results obtained from this analysis is discussed in brief in relation to the kind of fissile material, the extent of thermonuclear reaction in the weapon and the mode of detonation. (orig.) [de

Improved self-reliance shearing interferometric technique for collimation testing

Science.gov (United States)

Zhao, Mingshan; Li, Guohua; Wang, Zhaobing; Jing, Yaling; Li, Yi

1995-06-01

Self-reference single plate shearing interferometric technique used for collimation testing of light beams are briefly reviewed. Two improved configurations of this self-reference interferometry with an inclined screen and matched half-field interferograms are described in detail. Sensitivity of these configurations is analyzed and compared with that of the existing ones.

Benefits of the Multiple Echo Technique for Ultrasonic Thickness Testing

Energy Technology Data Exchange (ETDEWEB)

Elder, J.; Vandekamp, R.

2011-02-10

Much effort has been put into determining methods to make accurate thickness measurements, especially at elevated temperatures. An accuracy of +/- 0.001 inches is typically noted for commercial ultrasonic thickness gauges and ultrasonic thickness techniques. Codes and standards put limitations on many inspection factors including equipment, calibration tolerance and temperature variations. These factors are important and should be controlled, but unfortunately do not guarantee accurate and repeatable measurements in the field. Most technicians long for a single technique that is best for every situation, unfortunately, there are no 'silver bullets' when it comes to nondestructive testing. This paper will describe and discuss some of the major contributors to measurement error as well as some advantages and limitations of multiple echo techniques and why multiple echo techniques should be more widely utilized for ultrasonic thickness measurements.

Fabrication of flex sensors through direct ink write technique and its electrical characterization

Science.gov (United States)

Abas, Muhammad; Rahman, Khalid

2016-11-01

The present work is intended to fabricate low-cost flex sensor from conductive carbon paste using direct ink write (DIW) technique. DIW method is one of the additive manufacturing processes, which is capable to deposit a variety of material on a variety of substrates by a different mechanism to feature resolution at a microns level. It is widely used in the electronic industry for fabrication of PCBS and electrodes for different electronic devices. The DIW system in present study extrudes material stored in the syringe barrel through nozzle using compressed air. This mechanism will assist in creating patterns on a variety of substrates. Pneumatic controller is employed to control deposition of material, while computer-controlled X-Y stage is employed to control pattern generation. For effective and control patterning, printing parameters were optimized using Taguchi design optimization technique. The conductive carbon paste is used as ink for pattern generation on flexible PET substrate. Samples of flex sensor having different dimensions are prepared through DIW. The fabricated sensors were used as flexion sensor, and its electrical characteristic was evaluated. The obtained sensors are stable and reliable in performance.

An improved technique for oral administration of solutions of test ...

African Journals Online (AJOL)

Medicut intravenous cannula as an improvised oral cannula to administer solutions of drugs and test substances to experimental rats. Techniques of handling and manipulating the rat with the goal of having the eosophagus as straight as possible ...

Fracture toughness testing on ferritic alloys using the electropotential technique

International Nuclear Information System (INIS)

Huang, F.H.; Wire, G.L.

1981-01-01

Fracture toughness measurements as done conventionally require large specimens (5 x 5 x 2.5 cm) which would be prohibitively expensive to irradiate over the fluence and temperature ranges required for first wall design. To overcome this difficulty a single specimen technique for J intergral fracture toughness measurements on miniature specimens (1.6 cm OD x 0.25 cm thick) was developed. Comparisons with specimens three times as thick show that the derived J/sub 1c/ is constant, validating the specimen for first wall applications. The electropotential technique was used to obtain continuous crack extension measurements, allowing a ductile fracture resistence curve to be constructed from a single specimen. The irradiation test volume required for fracture toughness measurements using both miniature specimens and single specimen J measurements was reduced a factor of 320, making it possible to perform a systematic exploration of irradiation temperature and dose variables as required for qualification of HT-9 and 9Cr-1Mo base metal and welds for first wall application. Fracture toughness test results for HT-9 and 9Cr-1Mo from 25 to 539 0 C are presented to illustrate the single specimen technique

Intercomparison test of various aerosol measurement techniques

International Nuclear Information System (INIS)

Cherdron, W.; Hassa, C.; Jordan, S.

1984-01-01

At the suggestion of the CONT group (Containment Loading and Response), which is a subgroup of the Safety Working Group of the Fast Reactor Coordinating Committee, a group of experts undertook a comparison of the techniques of sodium aerosol measurement used in various laboratories in the EC. The following laboratories took part in the exercise: CEN-Mol (Belgium), CEA-Cadarache (France), CEA-Fontenay-aux-Roses (France), KfK-Karlsruhe (Federal Republic of Germany), ENEA-Bologna (Italy), and UKAEA-Winfrith (United Kingdom). The objective of the aerosol measurement workshop was to assess the applicability and reliability of specific aerosol measuring instruments. Measurements performed with equipment from the participating laboratories were evaluated using a standard procedure. This enabled an estimate of the accuracy of the experimental data to be provided for the verification of aerosol codes. Thus these results can be used as input for the physical modelling of aerosol behaviour, and the work reported here is a contribution to the definition of the radioactive source term for severe accidents in LMFBRs. The aerosol experts participating in the exercise agreed to concentrate on the techniques of measuring aerosol particle size distributions. The tests were performed at the FAUNA test facility using the aerosol loop. A sodium spray fire, which provides a continuous aerosol source of variable concentration, was produced under open-loop conditions in this facility. Although the primary objective of the workshop was to determine the particle size distributions of the aerosols, measurements of the sodium mass concentration were also made

Techniques for Automated Testing of Lola Industrial Robot Language Parser

Directory of Open Access Journals (Sweden)

M. M. Lutovac

2014-06-01

Full Text Available The accuracy of parsing execution directly affects the accuracy of semantic analysis, optimization and object code generation. Therefore, parser testing represents the basis of compiler testing. It should include tests for correct and expected, but also for unexpected and invalid cases. Techniques for testing the parser, as well as algorithms and tools for test sentences generation, are discussed in this paper. The methodology for initial testing of a newly developed compiler is proposed. Generation of negative test sentences by modifying the original language grammar is described. Positive and negative test cases generated by Grow, Purdom’s algorithm with and without length control, CDRC-P algorithm and CDRC-P algorithm with length control are applied to the testing of L-IRL robot programming language. For this purpose two different tools for generation of test sentences are used. Based on the presented analysis of possible solutions, the appropriate method can be chosen for testing the parser for smaller grammars with many recursive rules.

Applications of NLP Techniques to Computer-Assisted Authoring of Test Items for Elementary Chinese

Science.gov (United States)

Liu, Chao-Lin; Lin, Jen-Hsiang; Wang, Yu-Chun

2010-01-01

The authors report an implemented environment for computer-assisted authoring of test items and provide a brief discussion about the applications of NLP techniques for computer assisted language learning. Test items can serve as a tool for language learners to examine their competence in the target language. The authors apply techniques for…

Medium scale test study of chemical cleaning technique for secondary side of SG in PWR

International Nuclear Information System (INIS)

Zhang Mengqin; Zhang Shufeng; Yu Jinghua; Hou Shufeng

1997-08-01

The medium scale test study of chemical cleaning technique for removing corrosion product (Fe 3 O 4 ) in secondary side of SG in PWR has been completed. The test has been carried out in a medium scale test loop. The medium scale test evaluated the effect of the chemical cleaning technique (temperature, flow rate, cleaning time, cleaning process), the state of corrosion product deposition on magnetite (Fe 3 O 4 ) solubility and safety of materials of SG in cleaning process. The inhibitor component of chemical cleaning agent has been improved by electrochemical linear polarization method, the effect of inhibitor on corrosion resistance of materials have been examined in the medium scale test loop, the most components of chemical cleaning agent have been obtained, the EDTA is main component in cleaning agent. The electrochemical method for monitor corrosion of materials during cleaning process has been completed in the laboratory. The study of the medium scale test of chemical cleaning technique have had the optimum chemical cleaning technique for remove corrosion product in SG secondary side of PWR. (9 refs., 4 figs., 11 tabs.)

Non-destructive test of lock actuator component using neutron radiography technique

International Nuclear Information System (INIS)

Juliyanti; Setiawan; Sutiarso

2012-01-01

Non-destructive test of lock actuator using neutron radiography technique has been done. The lock actuator is a mechanical system which is controlled by central lock module consisting of electronic circuit which drives the lock actuator works accordingly to open and lock the vehicle door. The non-destructive test using neutron radiography is carried out to identify the type of defect is presence by comparing between the broken and the brand new one. The method used to test the lock actuator component is film method (direct method). The result show that the radiography procedure has complied with the ASTM standard for neutron radiography with background density of 2.2, 7 lines and 3 holes was seen in the sensitivity indicator (SI) and the quite good image quality was obtained. In the brand new actuator is seen that isolator part which separated the coils has melted. By this non-destructive test using neutron radiography technique is able to detect in early stage the type of component's defect inside the lock actuator without to dismantle it. (author)

Neutralization of red mud with pickling waste liquor using Taguchi's design of experimental methodology.

Science.gov (United States)

Rai, Suchita; Wasewar, Kailas L; Lataye, Dilip H; Mishra, Rajshekhar S; Puttewar, Suresh P; Chaddha, Mukesh J; Mahindiran, P; Mukhopadhyay, Jyoti

2012-09-01

'Red mud' or 'bauxite residue', a waste generated from alumina refinery is highly alkaline in nature with a pH of 10.5-12.5. Red mud poses serious environmental problems such as alkali seepage in ground water and alkaline dust generation. One of the options to make red mud less hazardous and environmentally benign is its neutralization with acid or an acidic waste. Hence, in the present study, neutralization of alkaline red mud was carried out using a highly acidic waste (pickling waste liquor). Pickling waste liquor is a mixture of strong acids used for descaling or cleaning the surfaces in steel making industry. The aim of the study was to look into the feasibility of neutralization process of the two wastes using Taguchi's design of experimental methodology. This would make both the wastes less hazardous and safe for disposal. The effect of slurry solids, volume of pickling liquor, stirring time and temperature on the neutralization process were investigated. The analysis of variance (ANOVA) shows that the volume of the pickling liquor is the most significant parameter followed by quantity of red mud with 69.18% and 18.48% contribution each respectively. Under the optimized parameters, pH value of 7 can be achieved by mixing the two wastes. About 25-30% of the total soda from the red mud is being neutralized and alkalinity is getting reduced by 80-85%. Mineralogy and morphology of the neutralized red mud have also been studied. The data presented will be useful in view of environmental concern of red mud disposal.

Testing aspects of advanced coherent electron cooling technique

Energy Technology Data Exchange (ETDEWEB)

Litvinenko, V.; Jing, Y.; Pinayev, I.; Wang, G.; Samulyak, R.; Ratner, D.

2015-05-03

An advanced version of the Coherent-electron Cooling (CeC) based on the micro-bunching instability was proposed. This approach promises significant increase in the bandwidth of the CeC system and, therefore, significant shortening of cooling time in high-energy hadron colliders. In this paper we present our plans of simulating and testing the key aspects of this proposed technique using the set-up of the coherent-electron-cooling proof-of-principle experiment at BNL.

Development of an in-situ synthesized multi-component reinforced Al–4.5%Cu–TiC metal matrix composite by FAS technique – Optimization of process parameters

Directory of Open Access Journals (Sweden)

Biswajit Das

2016-03-01

Full Text Available In the present investigation, an in-situ multi-component reinforced aluminium copper alloy based metal matrix composite was fabricated by the flux assisted synthesis (FAS technique. It was found from the optical microscopy analysis that TiC particles are formed in the composite. Further the present research investigates the feasibility and dry machining characteristics of Al–4.5%Cu/5TiC metal matrix composite in CNC milling machine using uncoated solid carbide end mill cutter. The effect of the machining parameters such as feed, cutting speed, depth of cut on the response parameters such as cutting force and COM is determined by using analysis of variance (ANOVA. From the analysis it was found that cutting speed and depth of cut played a major role in affecting cutting force. Multi output optimization of the process was carried out by the application of the Taguchi method with fuzzy logic, and the confirmatory test has revealed the accuracy of the developed model. For predicting the response parameters, regression equations were developed and verified with a number of test cases and it was observed that the percentage error for both responses is less than ±3%, which indicates there is a close agreement between the predicted and the measured results.

Fuzzy Cognitive Map for Software Testing Using Artificial Intelligence Techniques

OpenAIRE

Larkman , Deane; Mohammadian , Masoud; Balachandran , Bala; Jentzsch , Ric

2010-01-01

International audience; This paper discusses a framework to assist test managers to evaluate the use of AI techniques as a potential tool in software testing. Fuzzy Cognitive Maps (FCMs) are employed to evaluate the framework and make decision analysis easier. A what-if analysis is presented that explores the general application of the framework. Simulations are performed to show the effectiveness of the proposed method. The framework proposed is innovative and it assists managers in making e...

Advanced ultrasonic techniques for nondestructive testing of austenitic and dissimilar welds in nuclear facilities

Science.gov (United States)

Juengert, Anne; Dugan, Sandra; Homann, Tobias; Mitzscherling, Steffen; Prager, Jens; Pudovikov, Sergey; Schwender, Thomas

2018-04-01

Austenitic stainless steel welds as well as dissimilar metal welds with nickel alloy filler material, used in safety relevant parts of nuclear power plants, still challenge the ultrasonic inspection. The weld material forms large oriented grains that lead, on the one hand, to high sound scattering and, on the other hand, to inhomogeneity and to the acoustic anisotropy of the weld structure. The ultrasonic wave fronts do not propagate linearly, as in ferritic weld joints, but along the curves, which depend on the specific grain structure of the weld. Due to the influence of these phenomena, it is difficult to analyze the inspection results and to classify the ultrasonic indications, which could be both from the weld geometry and from the material defects. A correct flaw sizing is not possible. In an ongoing research project, different techniques to improve the reliability of ultrasonic testing at these kinds of welds are investigated. In a first step (in the previous research project) two ultrasonic inspection techniques were developed and validated on plane test specimens with artificial and realistic flaws. In the ongoing project, these techniques are applied to circumferential pipe welds with longitudinal and transverse flaws. The technique developed at the Federal Institute for Materials Research and Testing (BAM) in Germany uses a combination of ray tracing and synthetic aperture focusing technique (SAFT). To investigate the unknown grain structure, the velocity distribution of weld-transmitting ultrasound waves is measured and used to model the weld by ray tracing. The second technique, developed at the Fraunhofer Institute for Nondestructive Testing (IZFP) in Germany, uses Sampling Phased Array (Full Matrix Capture) combined with the reverse phase matching (RPM) and the gradient elastic constant descent algorithm (GECDM). This inspection method is able to estimate the elastic constants of the columnar grains in the weld and offers an improvement of the

Analysis of abrasive wear behavior of PTFE composite using Taguchi’s technique

Directory of Open Access Journals (Sweden)

Yusuf Şahin

2015-12-01

Full Text Available Polymeric composites are widely used for structural, aerospace, and automobile sectors due to their good combination of high specific strength and specific modulus. These two main characteristics make these materials attractive, compared to conventional materials like metal or alloy ones. Some of their typical benefits include easy processing, corrosion resistance, low friction, and damping of noise and vibrations. Wear behavior of Polytetrafluoroethylenes (PTFE and its composites including glass-filled composites and carbon-filled composites are investigated using a pin-on-disc configuration. A plan of experiments in terms of Taguchi technique is carried out to acquire data in controlled way. An orthogonal array (L9 and the analysis of variance are employed to investigate the influence of process parameters on the wear of these composites. Volume loss increased with abrasive size, load, and distance. Furthermore, specific wear rate decreased with increasing grit size, load, sliding distance, whereas, slightly with compressive strength. Optimal process parameters, which minimize the volume loss, were the factor combinations of L1, G3, D1, and C3. Confirmation experiments were conducted to verify the optimal testing parameters. It was found that in terms of volume loss, there was a good agreement between the estimated and the experimental value of S/N ratio with an error of 1.604%. Moreover, abrasive size, load, and sliding distance exerted a great effect on the specific wear rate, at 51.14, 27.77, and 14.70%, respectively.

An equipment test for grading lumber by transverse vibration technique

Directory of Open Access Journals (Sweden)

Marcelo Rodrigo Carreira

2008-08-01

Full Text Available Due to the great variability of its mechanical properties, the rational use of lumber for structural purposes is directly conditioned to its grading. There are several techniques available for grading structural lumber. The most relevant one is the transverse vibration technique which obtained reliable results in non-destructive evaluation of lumber. The purpose of this work is to present the bases for the mechanical grading of lumber and the results of the calibration test of the frst transverse vibration equipment developed in Brazil. In this research 30 beams of cupiúba (Goupia glabra with nominal dimensions of 5 cm X 10 cm X 300 cm, were used. The tests were accomplished at the Wood and Timber Structures Laboratory (LaMEM of the University of São Paulo (USP. The results showed a strong correlation between the elasticity modulus measured by the static bending test and the one obtained with the transverse vibration equipment, showing the high reliability of the vibration method for the grading of structural lumber. A determination coeffcient (R² of 0.896 was obtained with the Brazilian equipment, showing that it can be used in the grading of lumber.

An evaluation testing technique of single event effect using Beam Blanking SEM

Energy Technology Data Exchange (ETDEWEB)

Aoki, J; Hada, T; Pesce, A; Akutsu, T; Matsuda, S [National Space Development Agency of Japan, Tsukuba, Ibaraki (Japan). Tsukuba Space Center; Igarashi, T; Baba, S

1997-03-01

Beam Blanking SEM (Scanning Electron Microscope) testing technique has been applied to CMOS SRAM devices to evaluate the occurence of soft errors on memory cells. Cross-section versus beam current and LET curves derived from BBSEM and heavy ion testing technique, respectively, have been compared. A linear relation between BBSEM current and heavy ion LET has been found. The purpose of this study was to demonstrate that the application of focused pulsed electron beam could be a reliable, convenient and inexpensive tool to investigate the effects of heavy ions and high energy particles on memory devices for space application. (author)

Thermal design, rating and second law analysis of shell and tube condensers based on Taguchi optimization for waste heat recovery based thermal desalination plants

Science.gov (United States)

Chandrakanth, Balaji; Venkatesan, G; Prakash Kumar, L. S. S; Jalihal, Purnima; Iniyan, S

2018-03-01

The present work discusses the design and selection of a shell and tube condenser used in Low Temperature Thermal Desalination (LTTD). To optimize the key geometrical and process parameters of the condenser with multiple parameters and levels, a design of an experiment approach using Taguchi method was chosen. An orthogonal array (OA) of 25 designs was selected for this study. The condenser was designed, analysed using HTRI software and the heat transfer area with respective tube side pressure drop were computed using the same, as these two objective functions determine the capital and running cost of the condenser. There was a complex trade off between the heat transfer area and pressure drop in the analysis, however second law analysis was worked out for determining the optimal heat transfer area vs pressure drop for condensing the required heat load.

Accelerated test techniques for micro-circuits: Evaluation of high temperature (473 k - 573 K) accelerated life test techniques as effective microcircuit screening methods

Science.gov (United States)

Johnson, G. M.

1976-01-01

The application of high temperature accelerated test techniques was shown to be an effective method of microcircuit defect screening. Comprehensive microcircuit evaluations and a series of high temperature (473 K to 573 K) life tests demonstrated that a freak or early failure population of surface contaminated devices could be completely screened in thirty two hours of test at an ambient temperature of 523 K. Equivalent screening at 398 K, as prescribed by current Military and NASA specifications, would have required in excess of 1,500 hours of test. All testing was accomplished with a Texas Instruments' 54L10, low power triple-3 input NAND gate manufactured with a titanium- tungsten (Ti-W), Gold (Au) metallization system. A number of design and/or manufacturing anomalies were also noted with the Ti-W, Au metallization system. Further study of the exact nature and cause(s) of these anomalies is recommended prior to the use of microcircuits with Ti-W, Au metallization in long life/high reliability applications. Photomicrographs of tested circuits are included.

Parametric Study of Slurry-Erosion of Hydroturbine Steels with and without Detonation Gun Spray Coatings using Taguchi Technique

Science.gov (United States)

Grewal, Harpreet Singh; Bhandari, Sanjeev; Singh, Harpreet

2012-09-01

WC-Co-Cr coatings were deposited on some hydroturbine 13Cr4Ni and 16Cr5Ni steels by the detonation-gun spray process. An in-depth characterization of the as-sprayed coating was done using X-ray diffraction (XRD) and scanning electron microscopy (SEM)/energy-dispersive X-ray spectroscopy (EDS) techniques. Microhardness and porosity measurements were also made. The coating was found to have a typical splat-like morphology with some indications of unmelted carbide particles. The XRD results showed the presence of WC as the primary phase along with W2C and Co6W6C as secondary phases. Furthermore, the slurry erosion behavior of the coatings was investigated to ascertain the usefulness of the coatings to reduce the slurry erosion of the steels. The effect of four operating factors viz. the velocity, impact angle, concentration, and particle size on the slurry erosion of coated and bare steels has been studied using a high-speed jet-type test rig. The sand used as an erodent was collected from a power plant to replicate the actual turbine conditions. It has been observed that the given cermet coating can enhance the erosion resistance of the steel. Velocity was found to be the most significant factor affecting the erosion behavior of the coating, whereas it was the erodent particle size in the case of uncoated steel. As evidenced from the SEM images, the platelet mechanism of erosion seemed to be the prominent one, causing the removal of material from the surface of the steel, whereas for the coating, the formation and interlinking of cracks resulted in the removal of material.

The Effects of Reaction Variables on Solution Polymerization of Vinyl Acetate and Molecular Weight of Poly(vinyl alcohol Using Taguchi Experimental Design

Directory of Open Access Journals (Sweden)

M.H. Navarchian

2009-12-01

Full Text Available Poly(vinyl acetate is synthesized via solution polymerization, and then it is converted to poly(vinyl alcohol by alkaline alcoholysis. The aim of the work study was to investigate statistically the  influence of reaction variables in vinyl acetate polymerization, the conversion of this monomer to polymer, degree of branching of acetyl group in poly(vinyl acetate, as well as the molecular weight of poly(vinyl alcohol, using Taguchi experimental design approach. The reaction variables were polymerization time, molar ratio of initiator to monomer, and volume ratio of monomer to solvent. The statistical analysis of variance of the results revealed that all factors have significantly influenced the conversion and degree of branching. Volume ratio of monomer to solvent is the only factor affecting the molecular weight of poly(vinyl alcohol, and has the greatest influence on all responses. By increasing this ratio, the conversion, degree of branching of acetyl group in poly(vinyl acetate, and molecular weight of poly(vinyl alcohol were increased.

Program of in-pile IASCC testing under the simulated actual plant condition. Development of technique for in-pile IASCC initiation test in JMTR

International Nuclear Information System (INIS)

Ugachi, Hirokazu; Tsukada, Takashi; Kaji, Yoshiyuki; Nagata, Nobuaki; Dozaki, Koji; Takiguchi, Hideki

2003-01-01

Irradiation assisted stress corrosion cracking (IASCC) is caused by the synergistic effects of neutron irradiation, stress and corrosion by high temperature water. It is, therefore, essential to perform in-pile SCC tests, which are material tests under the conditions simulating those of actual LWR operation, in order to clarify the precise mechanism of the phenomenon, though mainly out-of-pile SCC tests for irradiated materials have been carried out in this research field. There are, however, many difficulties to perform in-pile SCC tests. Performing in-pile SCC tests, essential key techniques must be developed. Hence as a part of development of the key techniques for in-pile SCC tests, we have embarked on development of the test technique which enables us to obtain the information concerning the effect of such parameters as applied stress level, water chemistry, irradiation conditions, etc. on the crack initiation behavior. Although it is difficult to detect the crack initiation in in-pile SCC tests, the crack initiation can be evaluated by the detection of specimen rupture if the cross section area of the specimen is small enough. Therefore, we adopted the uniaxial constant loading (UCL) test with small tensile specimens. This paper will describe the current status of the development of several techniques for in-pile SCC initiation tests in JMTR and the results of the performance tests of the designed testing unit using the out-of-pile loop facility. (author)

Optimum combination of process parameters to optimize Surface Roughness and Chip Thickness during End Milling of Aluminium 6351-T6 Alloy Using Taguchi Grey Relational Analysis

Directory of Open Access Journals (Sweden)

Reddy Sreenivasulu

2017-06-01

Full Text Available In any machining operations, quality is the important conflicting objective. In order to give assurance for high productivity, some extent of quality has to be compromised. Similarly productivity will be decreased while the efforts are channelized to enhance quality. In this study,  the experiments were carried out on a CNC vertical machining center (KENT and INDIA Co. Ltd, Taiwan make to perform 10mm slots on Al 6351-T6 alloy work piece by K10 carbide, four flute end milling cutter as per taguchi design of experiments plan by L9 orthogonal array was choosen to determine experimental trials. Furthermore the spindle speed (rpm, the feed rate (mm/min and depth of cut (mm are regulated in these experiments. Surface roughness and chip thickness was measured by a surface analyser of Surf Test-211 series (Mitutoyo and Digital Micrometer (Mitutoyo with least count 0.001 mm respectively. Grey relational analysis was employed to minimize surface roughness and chip thickness by setting of optimum combination of machining parameters. Minimum surface roughness and chip thickness obtained with 1000 rpm of spindle speed, 50 mm/min feed rate and 0.7 mm depth of cut respectively. Confirmation experiments showed that Gray relational analysis precisely optimized the drilling parameters in drilling of Al 6351-T6 alloy.

Testing of reactor fuel materials using nuclear techniques

International Nuclear Information System (INIS)

Khouri, M.T.F.C.

1978-01-01

The tests presented here apply to: the quantitative determination of uranium in the core of fuel element plates by the detection of the number of neutrons produced in photo induced reactions in uranium; the determination of 235 U proportion in uranium dioxide samples, in the form of uranyl nitrate, by the technique of the detection of tracks produced by fission fragments and in pellet samples by passive gamma spectrometry and the checking of uranium homogenization distribution in fuel plates and uranium dioxide pellets. (Author) [pt

Fuel bundle examination techniques for the Phebus fission product test

International Nuclear Information System (INIS)

Blanc, J.Y.; Clement, B.; Hardt, P. von der

1996-01-01

The paper develops the non-destructive examinations, with a special emphasis on transmission tomography, performed in the Phebus facility, using a linear accelerator associated with a line scan camera based on PCD components. This particular technique enabled the high level of penetration to be obtained, necessary for this high density application. Spatial resolution is not far from the theoretical limit and the density resolution is often adequate. This technique permitted: 1) to define beforehand the cuts on a precise basis, avoiding a long step-by-step choice as in previous in-pile tests; 2) to determine, at an early stage, mass balance, material relocations (in association with axial gamma spectrometry), and FP distribution, as an input into re-calculations of the bundle events. However, classical cuttings, periscopic visual examinations, macrographies, micrographies and EPMA analyses remain essential to give oxidation levels (in the less degraded zones), phase aspect and composition, to distinguish between materials of identical density, and, if possible, to estimate temperatures. Oxidation resistance of sensors (thermocouples or ultrasonic thermometers) is also traced. The EPMA gives access to the molten material chemical analyses, especially in the molten fuel blockage area. The first results show that an important part of the fuel bundle melted (which was one of the objectives of this test) and that the degradation level is close to TIMI-2 with a molten plug under a cavity surrounded by an uranium-rich crust. In lower and upper areas fuel rods are less damaged. Complementaries between these examination techniques and between international teams involved will be major advantages in the Phebus FPT0 test comprehension. 3 refs, 9 figs

Technique Comparison of the Fracture Toughness Tests for Irradiated Fuel Claddings in a Hot Cell

International Nuclear Information System (INIS)

Ahn, Sangbok; Kim, Dosik; Jung, Yanghong; Choo, Yongsun; Ryu, Wooseog

2007-01-01

The degradation of a fracture toughness in a fuel cladding is a important factor to restrict the operation safety in nuclear power plants. The fracture properties of claddings were traditionally measured through a rubber bung test, a burst test, etc. Those results were the qualitative fracture characteristics, and could not be used as design or operation safety evaluation data. We need to evaluate the quantitative characteristics of claddings under normal operation and in accidents. The application of a fracture mechanics concept in testing a fuel cladding is restricted by the cladding geometry and creating the correct stress-state conditions. The geometry of claddings does not meet the requirement of the ASTM Standards for a specimen configuration and an applied load. The specimen may be produced from previously flattened claddings, but the flattening causes some uncertainties in the results due to changes in the microstructure of the material and a new distribution of the internal stresses. Therefore many efforts have been devoted to developing new test techniques, to quantify the fracture characteristics of claddings. Researchers from JAEA and NFI in Japan, Studsvik Company Ltd in Sweden, IAEA in Australia, and KAERI in Korea have independently developed fracture test techniques. This study is designed to review the independently developed techniques and to compare of their merits. Finally we shall apply the other techniques to upgrade our developing techniques

The perspectives of development of radiometric techniques for welded joints testing

International Nuclear Information System (INIS)

Troitskij, V.A.; Dovzhenko, V.N.

1987-01-01

The perspectives of development of radiometric techniques in non-destructive testing are presented. The problems of computer tomography, radiometric introscopy, electrorentgenography (xeroradiography) are reviewed. The aspects of application of low-silver detectors are also analysed. The studies on the problems mentioned above will be continued in order to eliminate expensive radiographic films and having in mind making the testing process faster. The design of individual dosemeters is also demonstrated. (author)

Biological removal of nickel (II by Bacillus sp. KL1 in different conditions: optimization by Taguchi statistical approach

Directory of Open Access Journals (Sweden)

Taran Mojtaba

2015-09-01

Full Text Available Bioremediation is the removal of heavy-metals such as nickel (Ni using microorganisms and has been considered as an important field in the biotechnology. Isolation and characterization of microorganisms exhibiting bioremediation activities and their optimization to treat polluted wastewaters is a vital and difficult task in remediation technologies. In this study, investigation was carried out to isolate Ni (II remediating microbial strains from soils contaminated with municipal solid waste leachate. Furthermore, Taguchi design of experiments were used to evaluate the influence of concentration, pH, temperature, and time on bioremediation of Ni (II using isolated bacteria. This study concluded that Bacillus sp. KL1 is a Ni (II-resistant strain and had Ni (II bioremediation activity. The highest bioremediation of Ni (II was observed as 55.06% after 24 h at 30ºC, pH 7, and 100 ppm concentration. Moreover, it was also observed that concentration is the most effective factor in the bioremediation process. In conclusion, we have demonstrated that bacteria isolated from soils contaminated with garbage leachate have the Bacillus sp. KL1 bacteria which can efficiently uptake and eliminate Ni (II from contaminated sites and thus makes it possible to treat heavy-metal containing wastewaters in industry by using this microorganism at optimized conditions.

Optimization of Recycled Glass Fibre-Reinforced Plastics Gear via Integration of the Taguchi Method and Grey Relational Analysis

Science.gov (United States)

Mizamzul Mehat, Nik; Syuhada Zakarria, Noor; Kamaruddin, Shahrul

2018-03-01

The increase in demand for industrial gears has resulted in the increase in usage of plastic-matrix composites particularly glass fibre-reinforced plastics as the gear materials. The usage of these synthetic fibers is to enhance the mechanical strength and the thermal resistance of the plastic gears. Nevertheless, the production of large quantities of these synthetic fibre-reinforced composites poses a serious threat to the ecosystem. Comprehending to this fact, the present work aimed at investigating the effects of incorporating recycled glass fibre-reinforced plastics in various compositions particularly on dimensional stability and mechanical properties of gear produced with diverse injection moulding processing parameters setting. The integration of Grey relational analysis (GRA) and Taguchi method was adopted to evaluate the influence of recycled glass fibre-reinforced plastics and variation in processing parameters on gear quality. From the experimental results, the blending ratio was found as the most influential parameter of 56.0% contribution in both improving tensile properties as well as in minimizing shrinkage, followed by mould temperature of 24.1% contribution and cooling time of 10.6% contribution. The results obtained from the aforementioned work are expected to contribute to accessing the feasibility of using recycled glass fibre-reinforced plastics especially for gear application.

Multidimensional Test Assembly Based on Lagrangian Relaxation Techniques. Research Report 98-08.

Science.gov (United States)

Veldkamp, Bernard P.

In this paper, a mathematical programming approach is presented for the assembly of ability tests measuring multiple traits. The values of the variance functions of the estimators of the traits are minimized, while test specifications are met. The approach is based on Lagrangian relaxation techniques and provides good results for the two…

A technique for extracting blood samples from mice in fire toxicity tests

Science.gov (United States)

Bucci, T. J.; Hilado, C. J.; Lopez, M. T.

1976-01-01

The extraction of adequate blood samples from moribund and dead mice has been a problem because of the small quantity of blood in each animal and the short time available between the animals' death and coagulation of the blood. These difficulties are particularly critical in fire toxicity tests because removal of the test animals while observing proper safety precautions for personnel is time-consuming. Techniques for extracting blood samples from mice were evaluated, and a technique was developed to obtain up to 0.8 ml of blood from a single mouse after death. The technique involves rapid exposure and cutting of the posterior vena cava and accumulation of blood in the peritoneal space. Blood samples of 0.5 ml or more from individual mice have been consistently obtained as much as 16 minutes after apparent death. Results of carboxyhemoglobin analyses of blood appeared reproducible and consistent with carbon monoxide concentrations in the exposure chamber.

Application of the Taguchi analytical method for optimization of effective parameters of the chemical vapor deposition process controlling the production of nanotubes/nanobeads.

Science.gov (United States)

Sharon, Maheshwar; Apte, P R; Purandare, S C; Zacharia, Renju

2005-02-01

Seven variable parameters of the chemical vapor deposition system have been optimized with the help of the Taguchi analytical method for getting a desired product, e.g., carbon nanotubes or carbon nanobeads. It is observed that almost all selected parameters influence the growth of carbon nanotubes. However, among them, the nature of precursor (racemic, R or Technical grade camphor) and the carrier gas (hydrogen, argon and mixture of argon/hydrogen) seem to be more important parameters affecting the growth of carbon nanotubes. Whereas, for the growth of nanobeads, out of seven parameters, only two, i.e., catalyst (powder of iron, cobalt, and nickel) and temperature (1023 K, 1123 K, and 1273 K), are the most influential parameters. Systematic defects or islands on the substrate surface enhance nucleation of novel carbon materials. Quantitative contributions of process parameters as well as optimum factor levels are obtained by performing analysis of variance (ANOVA) and analysis of mean (ANOM), respectively.

Taguchi Optimization of Cutting Parameters in Turning AISI 1020 MS with M2 HSS Tool

Science.gov (United States)

Sonowal, Dharindom; Sarma, Dhrupad; Bakul Barua, Parimal; Nath, Thuleswar

2017-08-01

In this paper the effect of three cutting parameters viz. Spindle speed, Feed and Depth of Cut on surface roughness of AISI 1020 mild steel bar in turning was investigated and optimized to obtain minimum surface roughness. All the experiments are conducted on HMT LB25 lathe machine using M2 HSS cutting tool. Ranges of parameters of interest have been decided through some preliminary experimentation (One Factor At a Time experiments). Finally a combined experiment has been carried out using Taguchi’s L27 Orthogonal Array (OA) to study the main effect and interaction effect of the all three parameters. The experimental results were analyzed with raw data ANOVA (Analysis of Variance) and S/N data (Signal to Noise ratio) ANOVA. Results show that Spindle speed, Feed and Depth of Cut have significant effects on both mean and variation of surface roughness in turning AISI 1020 mild steel. Mild two factors interactions are observed among the aforesaid factors with significant effects only on the mean of the output variable. From the Taguchi parameter optimization the optimum factor combination is found to be 630 rpm spindle speed, 0.05 mm/rev feed and 1.25 mm depth of cut with estimated surface roughness 2.358 ± 0.970 µm. A confirmatory experiment was conducted with the optimum factor combination to verify the results. In the confirmatory experiment the average value of surface roughness is found to be 2.408 µm which is well within the range (0.418 µm to 4.299 µm) predicted for confirmatory experiment.

Optimization of imaging parameters for SPECT scans of [99mTc]TRODAT-1 using Taguchi analysis.

Directory of Open Access Journals (Sweden)

Cheng-Kai Huang

Full Text Available Parkinson's disease (PD is a neurodegenerative disease characterized by progressive loss of dopaminergic neurons in the basal ganglia. Single photon emission computed tomography (SPECT scans using [99mTc]TRODAT-1 can image dopamine transporters and provide valuable diagnostic information of PD. In this study, we optimized the scanning parameters for [99mTc]TRODAT-1/SPECT using the Taguchi analysis to improve image quality. SPECT scans were performed on forty-five healthy volunteers according to an L9 orthogonal array. Three parameters were considered, including the injection activity, uptake duration, and acquisition time per projection. The signal-to-noise ratio (SNR was calculated from the striatum/occipital activity ratio as an image quality index. Ten healthy subjects and fifteen PD patients were used to verify the optimal parameters. The estimated optimal parameters were 962 MBq for [99mTc]TRODAT-1 injection, 260 min for uptake duration, and 60 s/projection for data acquisition. The uptake duration and time per projection were the two dominant factors which had an F-value of 18.638 (38% and 25.933 (53%, respectively. Strong cross interactions existed between the injection activity/uptake duration and injection activity/time per projection. Therefore, under the consideration of as low as reasonably achievable (ALARA for radiation protection, we can decrease the injection activity to 740 MBq. The image quality remains almost the same for clinical applications.

PENGUKURAN BIAYA KUALITAS : SUATU PARADIGMA ALTERNATIF

Directory of Open Access Journals (Sweden)

Monika Kussetya Ciptani

1999-01-01

Full Text Available Improving quality is an essential thing for a company to exist in the business competitive world. It's not time for a company to focus only on a high sales volume, but it's time for a company to focus on customer satisfaction. If the company can give customer satisfaction through their product, they will achieve maximum profit automatically. They are many method techniques to identify quality cost appeared in a company. It is very easy to control quality cost in a company if they are accounting data about it. But it will be very difficult to control the quality cost if the cost is hidden and can not be seen on accounting data. Variety techniques have been developed to solve this hidden quality cost. One of these method is Taguchi Method. By using Taguchi Method, a company will be helped to control and estimate quality cost especially hidden quality cost. Abstract in Bahasa Indonesia : Peningkatan Kualitas merupakan suatu hal yang paling esensial bagi suatu perusahaan untuk tetap eksis dalam dunia bisnis yang competitif ini. Kini sudah tidak jamannya lagi perusahaan hanya mementingkan volume penjualan yang begitu besar untuk mencapai keuntungan yang maksimal, tetapi lebih berorientasi pada aspek kepuasan konsumen. Dengan adanya kemampuan perusahaan untuk memberikan kepuasan terhadap konsumen yang membeli produknya, maka secara otomatis perusahaan akan mencapai keuntungan yang maksimal. Oleh karena itu dikembangkan berbagai cara dan teknik untuk mengidentifikasi besarnya biaya kualitas (kerugian yang muncul akibat barang yang dihasilkan menyimpang dari standar suatu perusahaan. Apabila biaya kualitas yang muncul tersebut nampak dalam catatan akuntansi perusahaan yang bersangkutan, maka perusahaan akan lebih mudah melakukan pengendalian, tetapi apabila biaya kualitas tersebut sifatnya tersembunyi, maka akan lebih sulit untuk melakukan pengendalian dan estimasi. Berbagai teknik telah dikembangkan untuk memecahkan masalah Hidden Quality Cost ini

The scratch test - Different critical load determination techniques. [adhesive strength of thin hard coatings

Science.gov (United States)

Sekler, J.; Hintermann, H. E.; Steinmann, P. A.

1988-01-01

Different critical load determination techniques such as microscopy, acoustic emission, normal, tangential, and lateral forces used for scratch test evaluation of complex or multilayer coatings are investigated. The applicability of the scratch test to newly developed coating techniques, systems, and applications is discussed. Among the methods based on the use of a physical measurement, acoustic emission detection is the most effective. The dynamics ratio between the signals below and above the critical load for the acoustic emission (much greater than 100) is well above that obtained with the normal, tangential, and lateral forces. The present commercial instruments are limited in load application performance. A scratch tester able to apply accurate loads as low as 0.01 N would probably overcome most of the actual limitations and would be expected to extend the scratch testing technique to different application fields such as optics and microelectronics.

Training guidelines in non-destructive testing techniques. 1991 edition

International Nuclear Information System (INIS)

1991-10-01

Non-destructive testing methods (NDT), by their very nature, allow components to be fully examined for properties or flaws without interfering with their usefulness. This grouping of inspection methods has grown from a handful of primitive techniques practised by artists to a widely known discipline which is an essential part of quality control, largely as a result of the standards demanded by the nuclear and aerospace industries. Recognizing the need for an international publication of NDT training syllabi, the IAEA Consultants Meeting on ''Qualification and Certification of NDT Personnel'' (Milan, 20-21 May 1986), recommended that the Agency publish the guidelines developed by Regional Working Group of the Latin America and Caribbean project. It was first issued in English in 1987 and has now been re-edited in English and Spanish and enlarged by the addition of programmes for other techniques

Development of small specimen test techniques. Development of a remote controlled small punch testing apparatus

International Nuclear Information System (INIS)

Ohmi, Masao; Saito, Junichi; Ooka, Norikazu; Jitsukawa, Shiro; Hishinuma, Akimichi; Umino, Akira.

1997-01-01

An accelerator-driven deuterium-lithium (d-Li) stripping reaction-type neutron source, such as the International Fusion Materials Irradiation Facility (IFMIF) planned by the International Energy Agency is recognized as one of the most promising facility to obtain test environments of high-energy neutrons for fusion reactor materials development. The limitation on the available irradiation volume of the irradiation facility requires the development of the small specimen test techniques (SSTT). Application of SSTT to evaluate the degradation of various components in the light water reactor for the life extension is expected to be also quite beneficial. A remote-controlled testing machine for the Small Punch (SP) and miniaturized tensile tests was developed at the hot laboratory of the Japan Materials Testing Reactor (JMTR). The machine is designed for testing at temperatures ranging between 93 and 1,123 K to evaluate the temperature dependence of the strength of materials including the embrittlement at low temperatures and the softening at elevated temperatures. The tests are performed in a vacuum or in an inert gas environment. The machine has been installed in a hot cell and is being used for the round robin test program of the SP test method. The round robin test program is planned to identify the capability of the test method and to establish a standard test procedure. The configuration and the specifications of the test machine are introduced and the results of the SP tests are also shown. (author)

Comparing interferometry techniques for multi-degree of freedom test mass readout

International Nuclear Information System (INIS)

Isleif, Katharina-Sophie; Gerberding, Oliver; Mehmet, Moritz; Schwarze, Thomas S; Heinzel, Gerhard; Danzmann, Karsten

2016-01-01

Laser interferometric readout systems with 1pm/Hz precision over long time scales have successfully been developed for LISA and LISA Pathfinder. Future gravitational physics experiments, for example in the fields of gravitational wave detection and geodesy, will potentially require similar levels of displacement and tilt readouts of multiple test masses in multiple degrees of freedom. In this article we compare currently available classic interferometry schemes with new techniques using phase modulations and complex readout algorithms. Based on a simple example we show that the new techniques have great potential to simplify interferometric readouts. (paper)

Influence of Cutting Fluid Flow Rate and Cutting Parameters on the Surface Roughness and Flank Wear of TiAlN Coated Tool In Turning AISI 1015 Steel Using Taguchi Method

Directory of Open Access Journals (Sweden)

Moganapriya C.

2017-09-01

Full Text Available This paper presents the influence of cutting parameters (Depth of cut, feed rate, spindle speed and cutting fluid flow rate on the surface roughness and flank wear of physical vapor deposition (PVD Cathodic arc evaporation coated TiAlN tungsten carbide cutting tool insert during CNC turning of AISI 1015 mild steel. Analysis of Variance has been applied to determine the critical influence of cutting parameters. Taguchi orthogonal test design has been employed to optimize the process parameters affecting surface roughness and tool wear. Depth of cut was found to be the most dominant factor contributing to high surface roughness (67.5% of the inserts. However, cutting speed, feed rate and flow rate of cutting fluid showed minimal contribution to surface roughness. On the other hand, cutting speed (45.6% and flow rate of cutting fluid (23% were the dominant factors influencing tool wear. The optimum cutting conditions for desired surface roughness constitutes the following parameters such as medium cutting speed, low feed rate, low depth of cut and high cutting fluid flow rate. Minimal tool wear was achieved for the following process parameters such as low cutting speed, low feed rate, medium depth of cut and high cutting fluid flow rate.

Enhanced specificity of TPMT*2 genotyping using unidirectional wild-type and mutant allele-specific scorpion primers in a single tube.

Directory of Open Access Journals (Sweden)

Dong Chen

Full Text Available Genotyping of thiopurine S-methyltransferase (TPMT is recommended for predicting the adverse drug response of thiopurines. In the current study, a novel version of allele-specific PCR (AS-PCR, termed competitive real-time fluorescent AS-PCR (CRAS-PCR was developed to analyze the TPMT*2 genotype in ethnic Chinese. This technique simultaneously uses wild-type and mutant allele-specific scorpion primers in a single reaction. To determine the optimal conditions for both traditional AS-PCR and CRAS-PCR, we used the Taguchi method, an engineering optimization process that balances the concentrations of all components using an orthogonal array rather than a factorial array. Instead of running up to 264 experiments with the conventional factorial method, the Taguchi method achieved the same optimization using only 16 experiments. The optimized CRAS-PCR system completely avoided non-specific amplification occurring in traditional AS-PCR and could be performed at much more relaxed reaction conditions at 1% sensitivity, similar to traditional AS-PCR. TPMT*2 genotyping of 240 clinical samples was consistent with published data. In conclusion, CRAS-PCR is a novel and robust genotyping method, and the Taguchi method is an effective tool for the optimization of molecular analysis techniques.

Estudio numerico y experimental del proceso de soldeo MIG sobre la aleacion 6063--T5 utilizando el metodo de Taguchi

Science.gov (United States)

Meseguer Valdenebro, Jose Luis

Electric arc welding processes represent one of the most used techniques on manufacturing processes of mechanical components in modern industry. The electric arc welding processes have been adapted to current needs, becoming a flexible and versatile way to manufacture. Numerical results in the welding process are validated experimentally. The main numerical methods most commonly used today are three: finite difference method, finite element method and finite volume method. The most widely used numerical method for the modeling of welded joints is the finite element method because it is well adapted to the geometric and boundary conditions in addition to the fact that there is a variety of commercial programs which use the finite element method as a calculation basis. The content of this thesis shows an experimental study of a welded joint conducted by means of the MIG welding process of aluminum alloy 6063-T5. The numerical process is validated experimentally by applying the method of finite element through the calculation program ANSYS. The experimental results in this paper are the cooling curves, the critical cooling time t4/3, the weld bead geometry, the microhardness obtained in the welded joint, and the metal heat affected zone base, process dilution, critical areas intersected between the cooling curves and the curve TTP. The numerical results obtained in this thesis are: the thermal cycle curves, which represent both the heating to maximum temperature and subsequent cooling. The critical cooling time t4/3 and thermal efficiency of the process are calculated and the bead geometry obtained experimentally is represented. The heat affected zone is obtained by differentiating the zones that are found at different temperatures, the critical areas intersected between the cooling curves and the TTP curve. In order to conclude this doctoral thesis, an optimization has been conducted by means of the Taguchi method for welding parameters in order to obtain an

Parameters optimization for friction spot welding of AZ31 magnesium alloy by Taguchi method Otimização dos parâmetros de soldagem por fricção por ponto da liga de magnésio AZ31 pelo método de Taguchi

Directory of Open Access Journals (Sweden)

Leonardo Contri Campanelli

2012-03-01

Full Text Available Friction spot welding (FSpW is a solid state welding process suitable for producing spot-like joints, especially in lightweight materials, which are particularly interesting due to the weight saving potential. The plunging of an especially designed non-consumable and rotating tool creates a connection between overlapped sheets through frictional heat and plastic deformation. Minimum material loss is observed, and therefore a fully consolidated joint with flat surface (no keyhole is obtained. In the current study, the effect of FSpW parameters, such as rotational speed, plunge depth and dwell time, on lap shear strength of AZ31 magnesium alloy joints was investigated. The optimization of input process parameters was carried out through Taguchi approach of DOE. Analysis of variance was applied to determine the individual importance of each parameter. Main effect plots were used to indicate the best levels for maximizing lap shear strength. The results show that tool plunge depth has the higher effect on the weld strength, followed by rotational speed and dwell time.A soldagem por fricção por ponto (FSpW é um processo de soldagem no estado sólido adequado para a produção de juntas pontuais, especialmente em materiais leves, que são particularmente interessantes devido ao potencial de redução de peso. A penetração de uma ferramenta não-consumível e rotacional especialmente desenvolvida cria uma junção entre as placas sobrepostas através de calor por fricção e deformação plástica. A perda de material é mínima, obtendo-se, portanto, uma junta totalmente consolidada com superfície plana (sem furo. Neste trabalho, investigou-se o efeito dos parâmetros do FSpW, tais como velocidade de rotação, profundidade de penetração e tempo de residência, na resistência ao cisalhamento das juntas de liga de magnésio AZ31. A otimização dos parâmetros de entrada do processo foi realizada através do método de Taguchi de DOE. A an

Virtual-stereo fringe reflection technique for specular free-form surface testing

Science.gov (United States)

Ma, Suodong; Li, Bo

2016-11-01

Due to their excellent ability to improve the performance of optical systems, free-form optics have attracted extensive interest in many fields, e.g. optical design of astronomical telescopes, laser beam expanders, spectral imagers, etc. However, compared with traditional simple ones, testing for such kind of optics is usually more complex and difficult which has been being a big barrier for the manufacture and the application of these optics. Fortunately, owing to the rapid development of electronic devices and computer vision technology, fringe reflection technique (FRT) with advantages of simple system structure, high measurement accuracy and large dynamic range is becoming a powerful tool for specular free-form surface testing. In order to obtain absolute surface shape distributions of test objects, two or more cameras are often required in the conventional FRT which makes the system structure more complex and the measurement cost much higher. Furthermore, high precision synchronization between each camera is also a troublesome issue. To overcome the aforementioned drawback, a virtual-stereo FRT for specular free-form surface testing is put forward in this paper. It is able to achieve absolute profiles with the help of only one single biprism and a camera meanwhile avoiding the problems of stereo FRT based on binocular or multi-ocular cameras. Preliminary experimental results demonstrate the feasibility of the proposed technique.

Soil solution extraction techniques for microbial ecotoxicity testing: a comparative evaluation.

Science.gov (United States)

Tiensing, T; Preston, S; Strachan, N; Paton, G I

2001-02-01

The suitability of two different techniques (centrifugation and Rhizon sampler) for obtaining the interstitial pore water of soil (soil solution), integral to the ecotoxicity assessment of metal contaminated soil, were investigated by combining chemical analyses and a luminescence-based microbial biosensor. Two different techniques, centrifugation and Rhizon sampler, were used to extract the soil solution from Insch (a loamy sand) and Boyndie (a sandy loam) soils, which had been amended with different concentrations of Zn and Cd. The concentrations of dissolved organic carbon (DOC), major anions (F- , CI-, NO3, SO4(2-)) and major cations (K+, Mg2+, Ca2+) in the soil solutions varied depending on the extraction technique used. Overall, the concentrations of Zn and Cd were significantly higher in the soil solution extracted using the centrifugation technique compared with that extracted using the Rhizon sampler technique. Furthermore, the differences observed between the two extraction techniques depended on the type of soil from which the solution was being extracted. The luminescence-based biosensor Escherichia coli HB101 pUCD607 was shown to respond to the free metal concentrations in the soil solutions and showed that different toxicities were associated with each soil, depending on the technique used to extract the soil solution. This study highlights the need to characterise the type of extraction technique used to obtain the soil solution for ecotoxicity testing in order that a representative ecotoxicity assessment can be carried out.

Black oil hydrate behavior : a comparison study of testing techniques : SINTEF Wheel and Multicell

Energy Technology Data Exchange (ETDEWEB)

Lund, A.; Hjarbo, K.W. [SINTEF Material and Chemistry, Trondheim (Norway); Larsen, R.; Straume, E.O.; Hoiland, S. [SINTEF Petroleum Research, Trondheim (Norway); Bracey, J.T. [BHP Billiton, Houston, TX (United States)

2008-07-01

SINTEF has developed a high pressure Multicell system to quickly screen possible inhibitor candidates for black oil systems in high pressure cells and loops. The hydrate self inhibiting properties of a black oil system were evaluated for gas/water and gas/water/oil systems at different water cuts. The oil system was then retested in a fluid flow loop system (Wheel). Different low dosage hydrate inhibitors (LDHI) were then screened in the Multicell system. The most promising inhibitors were tested further in the Wheel system. This paper presented the experimental results of these tests. The Multicell screening method allows 48 parallel low-volume samples to be compared simultaneously. The Wheel is suitable for more thorough testing of large-volume samples at harsh experimental conditions. Black oil samples were tested in this study using both techniques. Experiments were conducted to simulate shut-in and restart situations in a production line at field conditions. Both uninhibited oil and LDHI additives were tested. The Multicell was used to identify the critical water cut limit for uninhibited oil, and for screening the performance of the inhibitor for a large number of LDHIs at relevant conditions. The results from both testing techniques were found to be in good agreement. Both identified the same critical water cut limit. The Multicell technique was shown to be valuable for fast screening, testing and optimization of experimental conditions. However, the Wheel is needed for testing relevant flow behaviour of the systems. 1 ref., 4 tabs., 5 figs.

Development of enclosure technique of tag gas for in-pile creep test

International Nuclear Information System (INIS)

Izaki, Toru; Ichikawa, Shoichi; Soroi, Masatoshi; Ito, Chikara

2004-01-01

Outline of the enclosure technique of tag gas for in-pile creep test is stated. In order to carry out in-pile creep test, the sample can enclose tag gas before the test and then the sample is inserted into MARICO-2 (Material Testing Rig with Temperature Control) in FBR 'JOYO' MK-III for the irradiation test. Outline of in-pile creep test using tag gas, enclosure system of tag gas, detection of a part of broken sample and identification of sample are explained. 126-, 128-, 129-, 131-, 132-, and 134-Xe are used as tag gases. The samples are identified by RIMS (Laser Resonance Ionization Mass Spectroscopy) in ppt order. ODS ferritic steel will be tested by the method in the next step. (S.Y.)

Site characterization and validation - equipment design and techniques used in single borehole hydraulic testing, simulated drift experiment and crosshole testing

International Nuclear Information System (INIS)

Holmes, D.C.; Sehlstedt, M.

1991-10-01

This report describes the equipment and techniques used to investigate the variation of hydrogeological parameters within a fractured crystalline rock mass. The testing program was performed during stage 3 of the site characterization and validation programme at the Stripa mine in Sweden. This programme used a multidisciplinary approach, combining geophysical, geological and hydrogeological methods, to determine how groundwater moved through the rock mass. The hydrogeological work package involved three components. Firstly, novel single borehole techniques (focused packer testing) were used to determine the distribution of hydraulic conductivity and head along individual boreholes. Secondly, water was abstracted from boreholes which were drilled to simulate a tunnel (simulated drift experiment). Locations and magnitudes of flows were measured together with pressure responses at various points in the SCV rock mass. Thirdly, small scale crosshole tests, involving detailed interference testing, were used to determine the variability of hydrogeological parameters within previously identified, significant flow zones. (au)

Development status of ultrasonic test techniques for cast stainless steel

International Nuclear Information System (INIS)

Nishikawa, Yoshito

2015-01-01

Ultrasonic testing has been thought to be difficult to apply to cast stainless steel which is used as the material for the main coolant pipes in pressurized water reactors (PWRs). An ultrasonic testing technique using large aperture twin crystal transducers was developed in INSS for application to inspection of the main coolant pipes. The method was evaluated in an application to detect circumferential and axial defects in the cast stainless steel pipes. It was found that (1) the defects could be detected which had a depth that was so small that their evaluation was not required; and (2) depth sizing and length sizing of detected defects were also possible. (author)

Method-independent, Computationally Frugal Convergence Testing for Sensitivity Analysis Techniques

Science.gov (United States)

Mai, J.; Tolson, B.

2017-12-01

The increasing complexity and runtime of environmental models lead to the current situation that the calibration of all model parameters or the estimation of all of their uncertainty is often computationally infeasible. Hence, techniques to determine the sensitivity of model parameters are used to identify most important parameters. All subsequent model calibrations or uncertainty estimation procedures focus then only on these subsets of parameters and are hence less computational demanding. While the examination of the convergence of calibration and uncertainty methods is state-of-the-art, the convergence of the sensitivity methods is usually not checked. If any, bootstrapping of the sensitivity results is used to determine the reliability of the estimated indexes. Bootstrapping, however, might as well become computationally expensive in case of large model outputs and a high number of bootstraps. We, therefore, present a Model Variable Augmentation (MVA) approach to check the convergence of sensitivity indexes without performing any additional model run. This technique is method- and model-independent. It can be applied either during the sensitivity analysis (SA) or afterwards. The latter case enables the checking of already processed sensitivity indexes. To demonstrate the method's independency of the convergence testing method, we applied it to two widely used, global SA methods: the screening method known as Morris method or Elementary Effects (Morris 1991) and the variance-based Sobol' method (Solbol' 1993). The new convergence testing method is first scrutinized using 12 analytical benchmark functions (Cuntz & Mai et al. 2015) where the true indexes of aforementioned three methods are known. This proof of principle shows that the method reliably determines the uncertainty of the SA results when different budgets are used for the SA. The results show that the new frugal method is able to test the convergence and therefore the reliability of SA results in an

Updating of actual technique for ultrasonic testing of austenitic stainless materials and welds

International Nuclear Information System (INIS)

Lindholm, P.O.; Pers-Anderson, E.B.

1982-01-01

The technique for ultrasonic testing of stainless austenitic steels and weldings has been studied and it has been brought to the latest standard. Many problems exist when testing, the most serious being the occurence of false indications and the damping of energy. Laboratory tests show that the detectors with transversal sound waves should be used for plane defects. Best results were achieved with a 45 degrees detector. (GB)

Preparation of sodium beta″-alumina electrolyte thin film by electrophoretic deposition using Taguchi experimental design approach

International Nuclear Information System (INIS)

Wei, Xiao-ling; Xia, Yi; Liu, Xiao-min; Yang, Hui; Shen, Xiao-dong

2014-01-01

Highlights: • Sodium beta″ alumina electrolyte thin film is successfully prepared via electrophoretic deposition. • The ionic conductivity of the optimized electrolyte disk is 0.138 S cm -1 . • A Daniell-typed cell is built which approves the reversible Na + conduction at only 100 °C. - Abstract: With the desire to lowering the working temperature of Na-β″-Al 2 O 3 solid electrolyte (BASE) based batteries, electrophoretic deposition process is employed to fabricate 300 μm thick Na-β″-Al 2 O 3 sheet with densification microstructure and high ionic conductivity. Taguchi design of experiment approach with signal to noise ratio analysis is utilized to optimize the operation parameters. The results show that the TiO 2 content in the precursor powders is critical to determine the ionic conductivity of the resulting electrolyte. X-Ray diffraction analysis and X-ray photoelectron spectroscopy examination point out that Ti 4+ can enter the crystal lattice of Na-β″-Al 2 O 3 , which results in the variation of lattice parameters, densifies the microstructure and improves both β″ phase content and ionic conductivity of the resulting sample. The thin Na-β″-Al 2 O 3 disk obtained under the optimized conditions Exhibit 97% β″ phase content and relatively high ionic conductivity. Moreover, a Daniell-typed cell built with this optimized sample disk, using copper/zinc redox couples as electrodes and 1 M NaBF 4 in DMSO as the secondary electrolyte, shows reversible charge and discharge behaviors at relatively low temperature, 100 °C

Furnace Brazing Parameters Optimized by Taguchi Method and Corrosion Behavior of Tube-Fin System of Automotive Condensers

Science.gov (United States)

Guía-Tello, J. C.; Pech-Canul, M. A.; Trujillo-Vázquez, E.; Pech-Canul, M. I.

2017-08-01

Controlled atmosphere brazing has a widespread industrial use in the production of aluminum automotive heat exchangers. Good-quality joints between the components depend on the initial condition of materials as well as on the brazing process parameters. In this work, the Taguchi method was used to optimize the brazing parameters with respect to corrosion performance for tube-fin mini-assemblies of an automotive condenser. The experimental design consisted of five factors (micro-channel tube type, flux type, peak temperature, heating rate and dwell time), with two levels each. The corrosion behavior in acidified seawater solution pH 2.8 was evaluated through potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) measurements. Scanning electron microscope (SEM) and energy-dispersive x-ray spectroscopy (EDS) were used to analyze the microstructural features in the joint zone. The results showed that the parameters that most significantly affect the corrosion rate are the type of flux and the peak temperature. The optimal conditions were: micro-channel tube with 4.2 g/m2 of zinc coating, standard flux, 610 °C peak temperature, 5 °C/min heating rate and 4 min dwell time. The corrosion current density value of the confirmation experiment is in excellent agreement with the predicted value. The electrochemical characterization for selected samples gave indication that the brazing conditions had a more significant effect on the kinetics of the hydrogen evolution reaction than on the kinetics of the metal dissolution reaction.

Sadhana | Indian Academy of Sciences

Indian Academy of Sciences (India)

This study focused on using the Taguchi technique to optimize the process parameters ... Gu ¨mu ¨s¸ova Vocational School of Higher Education, Du ¨zce University, 81850 ... Manuscript received: 14 April 2014; Manuscript revised: 8 June 2016 ...

Sensitivity of field tests, serological and molecular techniques for Plum Pox Virus detection in various tissues

Directory of Open Access Journals (Sweden)

Mojca VIRŠČEK MARN

2015-12-01

Full Text Available Sensitivity of field tests (AgriStrip  and Immunochromato, DAS-ELISA, two step RT-PCR and real-time RT-PCR for Plum pox virus (PPV detection was tested in various tissues of apricot, peach, plum and damson plum trees infected with isolates belonging to PPV-D, PPV-M or PPV-Rec, the three strains present in Slovenia. Flowers of apricot and plum in full bloom proved to be a very good source for detection of PPV. PPV could be detected with all tested techniques in symptomatic parts of leaves in May and with one exception even in the beginning of August, but it was not detected in asymptomatic leaves using field tests, DAS-ELISA and partly also molecular techniques. PPV was detected only in some of the samples of asymptomatic parts of the leaves with symptoms and of stalks by field tests and DAS-ELISA. Infections were not detected in buds in August using field tests or DAS-ELISA. Field tests are useful for confirmation of the PPV infection in symptomatic leaves, but in tissues without symptoms DAS-ELISA should be combined or replaced by molecular techniques.

Experimental Research and Mathematical Modeling of Parameters Effecting on Cutting Force and SurfaceRoughness in CNC Turning Process

Science.gov (United States)

Zeqiri, F.; Alkan, M.; Kaya, B.; Toros, S.

2018-01-01

In this paper, the effects of cutting parameters on cutting forces and surface roughness based on Taguchi experimental design method are determined. Taguchi L9 orthogonal array is used to investigate the effects of machining parameters. Optimal cutting conditions are determined using the signal/noise (S/N) ratio which is calculated by average surface roughness and cutting force. Using results of analysis, effects of parameters on both average surface roughness and cutting forces are calculated on Minitab 17 using ANOVA method. The material that was investigated is Inconel 625 steel for two cases with heat treatment and without heat treatment. The predicted and calculated values with measurement are very close to each other. Confirmation test of results showed that the Taguchi method was very successful in the optimization of machining parameters for maximum surface roughness and cutting forces in the CNC turning process.

Dynamic Mechanical Testing Techniques for Cortical and Cancellous Bone

Science.gov (United States)

Cloete, Trevor

2017-06-01

Bone fracture typically occurs as an impact loading event (sporting accidents, vehicle collisions), the simulation of which requires in-depth understanding of dynamic bone behavior. Bone is a natural composite material with a complex multi length-scale hierarchical microstructure. At a macroscopic level, it is classified into hard/compact cortical bone and soft/spongy cancellous (trabecular) bone, though both are low-impedance materials relative to steels. Cortical bone is predominant in long bones, while in complex bone geometries (joints, flat bones) a cancellous bone core supports a thin cortical shell. Bone has primarily been studied at quasi-static strain rates (ɛ˙ failure, with interrupted quasi-static tests revealing a strong microstructure dependence. However, bone specimens are typically destroyed during dynamic tests, leading to a lack of dynamic microstructural damage investigations. In this paper, a short overview of dynamic bone testing is presented to give context to the challenges of testing low impedance, strain-rate dependent, non-linear, visco-elastic-brittle materials. Recent state-of-the-art experimental developments in dynamic bone testing are reviewed, with emphasis on pulse shaping, momentum trapping and ISR testing. These techniques allow for dynamic bone testing at small strains and near-constant strain rates with intact specimen recovery. The results are compared to those obtained with varying strain rate tests. Interrupted dynamic test results with microstructural analysis of the recovered specimens are presented and discussed. The paper concludes with a discussion of the experimental and modeling challenges that lie ahead in the field of dynamic bone behavior. The financial assistance of the National Research Foundation and the University of Cape Town towards this research is hereby acknowledged. Opinions expressed and conclusions arrived at are those of the author alone.

In-pile creep test technique for zirconium alloys examination in BR-10 reactor channels

International Nuclear Information System (INIS)

Pevchikh, Yu.M.; Kruglov, A.S.; Troyanov, V.M.

2002-01-01

The irradiation enhanced creep phenomenon was discovered in stainless steels as a specific physical process accompanying high-intensity neutron flux irradiation in fast reactors. IPPE is also experienced in irradiation creep test activities, studying different types of materials under irradiation in BR-10 fast reactor. Series of in-channel type test facilities were constructed and tested in BR-10 reactor's 'dry' channels in order to carry out full-scale instrumented examination regarded to in-pile creep behaviour of different reactor materials. As a result, a specific test technique, named 'Tensometric method', has been developed and experimentally proved to be power enough in order to investigate irradiation creep of materials right in situ under neutron irradiation. The main peculiarity of test facility, which is constructed to apply the tensometric method, consists in absence of any special deformation-measurement cell at all. The in-pile creep strain measurement technique developed at IPPE is based on the non-direct measurement of specimen's deformation (either linear tensile strain or angular twisting one), which directly affects the loaded draws' tension parameters. Starting from 1993, in-pile creep experiments to investigate in-reactor creep behaviour of E110 and E635 zirconium alloys were carried out in BR-10. Experimental results and data collected during more than 20-year of BR-10 in-reactor creep test experience can be assumed as a strong evidence that the tensometric technique is a powerful instrument, which can give a chance to study different irradiation effects on reactor materials directly under irradiation. (author)

[The quantitative testing of V617F mutation in gen JAK2 using pyrosequencing technique].

Science.gov (United States)

Dunaeva, E A; Mironov, K O; Dribnokhodova, T E; Subbotina, E E; Bashmakova; Ol'hovskiĭ, I A; Shipulin, G A

2014-11-01

The somatic mutation V617F in gen JAK2 is a frequent cause of chronic myeloprolific diseases not conditioned by BCR/ABL mutation. The quantitative testing of relative percentage of mutant allele can be used in establishing severity of disease and its prognosis and in prescription of remedy inhibiting activity of JAK2. To quantitatively test mutation the pyrosequencing technique was applied. The developed technique permits detecting and quantitatively, testing percentage of mutation fraction since 7%. The "gray zone" is presented by samples with percentage of mutant allele from 4% to 7%. The dependence of expected percentage of mutant fraction in analyzed sample from observed value of signal is described by equation of line with regression coefficients y = - 0.97, x = -1.32 and at that measurement uncertainty consists ± 0.7. The developed technique is approved officially on clinical material from 192 patients with main forms of myeloprolific diseases not conditioned by BCR/ABL mutation. It was detected 64 samples with mautant fraction percentage from 13% to 91%. The developed technique permits implementing monitoring of therapy of myeloprolific diseases and facilitates to optimize tactics of treatment.

Seismic qualification using digital signal processing/modal testing and finite element techniques

International Nuclear Information System (INIS)

Steedman, J.B.; Edelstein, A.

1983-01-01

A systematic procedure in which digital signal processing, modal testing and finite element techniques can be used to seismically qualify Class IE equipment for use in nuclear generating stations is presented. A new method was also developed in which measured transmissibility functions and Fourier transformation techniques were combined to compute instrument response spectra. As an illustrative example of the qualification method, the paper follows the qualification of a safety related Class IE Heating, Ventilating, and Air Conditioning (HVAC) Control Panel subjected to both seismic and hydrodynamic loading conditions

New test structures and techniques for measurement of mechanical properties of MEMS materials

Science.gov (United States)

Sharpe, William N., Jr.; Yuan, Bin; Vaidyanathan, Ranji; Edwards, Richard L.

1996-09-01

This paper presents techniques and procedures for addressing the three major problems of mechanical testing of the thin films used in surface micromachined microelectromechanical systems--specimen handling, friction, and strain measurement. The polysilicon tensile specimens are fabricated with two supporting side strips on silicon wafers at the Microelectronic Center of North Carolina. The tensile specimen is released by etching away the wafer, and the two support strips are cut after the specimen is glued in the test machine. Friction is reduced by a linear air bearing in the load train, and strain is measured with a noncontacting technique based on laser interferometry between two gold lines on the tensile specimen. The Young's modulus of polysilicon is 170 +/- 7 GPa and the strength is 1.21 +/- 0.16 GPa from a series of 29 tests. preliminary measurements have been made of Poisson's ratio and the fatigue behavior, and an attempt is underway to measure the fracture toughness.

Fundamental and assessment of concrete structure monitoring by using acoustic emission technique testing: A review

Science.gov (United States)

Desa, M. S. M.; Ibrahim, M. H. W.; Shahidan, S.; Ghadzali, N. S.; Misri, Z.

2018-04-01

Acoustic emission (AE) technique is one of the non-destructive (NDT) testing, where it can be used to determine the damage of concrete structures such as crack, corrosion, stability, sensitivity, as structure monitoring and energy formed within cracking opening growth in the concrete structure. This article gives a comprehensive review of the acoustic emission (AE) technique testing due to its application in concrete structure for structural health monitoring (SHM). Assessment of AE technique used for structural are reviewed to give the perception of its structural engineering such as dam, bridge and building, where the previous research has been reviewed based on AE application. The assessment of AE technique focusing on basic fundamental of parametric and signal waveform analysis during analysis process and its capability in structural monitoring. Moreover, the assessment and application of AE due to its function have been summarized and highlighted for future references

Metamodel-based robust simulation-optimization : An overview

NARCIS (Netherlands)

Dellino, G.; Meloni, C.; Kleijnen, J.P.C.; Dellino, Gabriella; Meloni, Carlo

2015-01-01

Optimization of simulated systems is the goal of many methods, but most methods assume known environments. We, however, develop a "robust" methodology that accounts for uncertain environments. Our methodology uses Taguchi's view of the uncertain world but replaces his statistical techniques by

Optimization and Development of Swellable Controlled Porosity ...

African Journals Online (AJOL)

Purpose: To develop swellable controlled porosity osmotic pump tablet of theophylline and to define the formulation and process variables responsible for drug release by applying statistical optimization technique. Methods: Formulations were prepared based on Taguchi Orthogonal Array design and Fraction Factorial ...

Isotope techniques in non-destructive testing of dynamic systems

International Nuclear Information System (INIS)

Singh, Gursharan; Pant, H.J.

1996-01-01

A few applications of gamma scanning and radiotracer techniques for Non-destructive Testing (NDT) of dynamic systems in chemical and petrochemical industries are briefly discussed in this paper. Examples of gamma scanning inspections carried out for troubleshooting of various types of columns such as vacuum, extraction, separator and rectifier, with trays and packed beds and having diameters from 1 meter to 8.4 meters are given. Radiotracer applications for Residence Time Distribution (RTD) studies on different systems like an aniline production reactor in a chemical industry and a laboratory scale solid-liquid fluidized bed column are mentioned. (author)

Multiple group radiator and hybrid test heads, possibilities of combining the array technique

International Nuclear Information System (INIS)

Wuestenberg, H.

1993-01-01

This article is intended to show the important considerations, which led to the development of the multichannel group radiator technique. Trends in development and the advantages and disadvantages of the different possibilities are introduced, against the background of experience now available for these configurative variants of ultrasonic test heads. For this reason, a series of experiences and arguments is reported, from the point of view of the developer of the multi-channel group radiator technique. (orig./HP) [de

Parametric Modal Study and Optimization of the Floor Pan of a B-Segment Automotive Using a Hybrid Method of Taguchi and a Newly Developed MCDM Model

Directory of Open Access Journals (Sweden)

Mohammad Hassan Shojaeefard

Full Text Available Abstract The floor pan is an important component that connects the front and rear segments of the automotive underbody structure. Global stiffness and NVH characteristics of BIW are highly dependent to shape, thickness and mass of the body panels and could be evaluated by modal characteristics of these panels. The feeling of solidness and comfort of passengers in an automotive is also dependent to the modal behavior of the underbody components as well as the floor pan. On the other hand, it is desired to reduce the total mass of the floor pan, in order to have a lighter vehicle with better fuel economy and emission standards. In this paper, the effect of geometrical parameters on natural frequency and total mass of the floor pan of a conventional B-Segment automotive body is investigated using finite element simulation. The finite element model is verified using an experimental test on the floor pan. Taguchi L 16 orthogonal array is used to design the numerical experiments. Subsequently, S/N ratio analysis is performed to evaluate the effect of each design variable on the output functions. The panel's thickness is determined to have the most contribution in affecting the natural frequency and weight using Analysis of Variance (ANOVA. The best combination of geometrical variables which leads to the trade-off results is then figured out by a new multi-criteria decision making (MCDM method developed in this study. Accuracy of this method is verified by comparing the trade-off results with TOPSIS, as a conventional MCDM method.

A Taguchi PCA fuzzy-based approach for the multi-objective extended optimization of a miniature optical engine

International Nuclear Information System (INIS)

Fan Yichin; Tzeng Yihfong; Li Sixiang

2008-01-01

The paper proposes a hybrid approach, integrating a combination of Taguchi methods, principal component analysis (PCA) and fuzzy theory for the extended optimization of multiple quality characteristics in optimization experiments of non-image optics; a miniature light emitting diode pocket-sized projection display system is demonstrated in this research as an optimization sample. Traditionally, the performance of projector optics can be evaluated by modulation transfer function and its optimization method is DLS (damped least square). Comparatively, light efficiency and uniformity play a part in non-image optics where the optimized method is based on the concept of non-sequential rays; for example, in the optical engine of a projector, which demands better light efficiency and uniformity. The DLS method is occasionally employed in the optimization of non-image optics such as optical engines, but it is sometimes sensitive to the number of rays employed and some over-optimization problems. In this research we propose as an alternative method to optimize in an extended way the optical engine of a miniature projector. Control factors were checked and then repeatedly examined before the experiments started. In the experiment, optimization works through an L18 orthogonal array. Finally, this proposed optimization work shows good success for the optimization of non-image optical engines because this method is less sensitive to the number of non-sequential rays. Compared with the initial design, the optimized parameter design is able to improve the luminous flux by 11.46 dB, the illumination uniformity by 3.14 and the packing size by 1.125 dB

Failure modes induced by natural radiation environments on DRAM memories: study, test methodology and mitigation technique

International Nuclear Information System (INIS)

Bougerol, A.

2011-05-01

DRAMs are frequently used in space and aeronautic systems. Their sensitivity to cosmic radiations have to be known in order to satisfy reliability requirements for critical applications. These evaluations are traditionally done with particle accelerators. However, devices become more complex with technology integration. Therefore new effects appear, inducing longer and more expensive tests. There is a complementary solution: the pulsed laser, which triggers similar effects as particles. Thanks to these two test tools, main DRAM radiation failure modes were studied: SEUs (Single Event Upset) in memory blocks, and SEFIs (Single Event Functional Interrupt) in peripheral circuits. This work demonstrates the influence of test patterns on SEU and SEFI sensitivities depending on technology used. In addition, this study identifies the origin of the most frequent type of SEFIs. Moreover, laser techniques were developed to quantify sensitive surfaces of the different effects. This work led to a new test methodology for industry, in order to optimize test cost and efficiency using both pulsed laser beams and particle accelerators. Finally, a new fault tolerant technique is proposed: based on DRAM cell radiation immunity when discharged, this technique allows to correct all bits of a logic word. (author)

Triaxial testing system for pressure core analysis using image processing technique

Science.gov (United States)

Yoneda, J.; Masui, A.; Tenma, N.; Nagao, J.

2013-11-01

In this study, a newly developed innovative triaxial testing system to investigate strength, deformation behavior, and/or permeability of gas hydrate bearing-sediments in deep sea is described. Transport of the pressure core from the storage chamber to the interior of the sealing sleeve of a triaxial cell without depressurization was achieved. An image processing technique was used to capture the motion and local deformation of a specimen in a transparent acrylic triaxial pressure cell and digital photographs were obtained at each strain level during the compression test. The material strength was successfully measured and the failure mode was evaluated under high confining and pore water pressures.

Validity of a cross-specialty test in basic laparoscopic techniques (TABLT)

DEFF Research Database (Denmark)

Thinggaard, Ebbe; Bjerrum, Flemming; Strandbygaard, Jeanett

2015-01-01

. The aim of this study was to establish validity evidence for the Training and Assessment of Basic Laparoscopic Techniques (TABLT) test, a tablet-based training system. METHODS: Laparoscopic surgeons and trainees were recruited from departments of general surgery, gynaecology and urology. Participants...... included novice, intermediate and experienced surgeons. All participants performed the TABLT test. Performance scores were calculated based on time taken and errors made. Evidence of validity was explored using a contemporary framework of validity. RESULTS: Some 60 individuals participated. The TABLT...... was shown to be reliable, with an intraclass correlation coefficient of 0·99 (P value of 0·73 (P 

Digital Image Correlation Techniques Applied to Large Scale Rocket Engine Testing

Science.gov (United States)

Gradl, Paul R.

2016-01-01

Rocket engine hot-fire ground testing is necessary to understand component performance, reliability and engine system interactions during development. The J-2X upper stage engine completed a series of developmental hot-fire tests that derived performance of the engine and components, validated analytical models and provided the necessary data to identify where design changes, process improvements and technology development were needed. The J-2X development engines were heavily instrumented to provide the data necessary to support these activities which enabled the team to investigate any anomalies experienced during the test program. This paper describes the development of an optical digital image correlation technique to augment the data provided by traditional strain gauges which are prone to debonding at elevated temperatures and limited to localized measurements. The feasibility of this optical measurement system was demonstrated during full scale hot-fire testing of J-2X, during which a digital image correlation system, incorporating a pair of high speed cameras to measure three-dimensional, real-time displacements and strains was installed and operated under the extreme environments present on the test stand. The camera and facility setup, pre-test calibrations, data collection, hot-fire test data collection and post-test analysis and results are presented in this paper.

Laboratory testing of closure cap repair techniques

International Nuclear Information System (INIS)

Persoff, P.; Moridis, G.; Tuck, D.M.

1996-10-01

Landfill design requires a low permeability closure cap as well as a low permeability liner. The Savannah River Site, in South Carolina, has approximately 85 acres of mixed waste landfills covered with compacted kaolin clay. Maintaining low permeability of the clay cap requires both that the permeability of the compacted clay itself remain low and that the integrity of the barrier be maintained. Barrier breaches typically result from penetration by roots or animals, and especially cracks caused by uneven settling or desiccation. In this study, clay layers, 0.81 m in diameter and 7.6 cm thick, were compacted in 7 lysimeters to simulate closure caps. The hydraulic conductivity of each layer was measured, and the compacted clay layers (CCL's) were cracked by drying. Then various repair techniques were applied and the effectiveness of each repair was assessed by remeasuring the hydraulic conductivity. Finally the repaired CCL was again dried and measured to determine how the repair responded to the conditions that caused the original failure. For a full report of this investigation see Persoff et al. Six repair techniques have been tested, four of which involve the use of injectable barrier liquids colloidal silica (CS) and polysiloxane (PSX) described below: (I) covering the crack with a bentonite geosynthetic clay liner (GCL), (ii) recompaction of new kaolinite at STD+3 moisture content joined to existing kaolinite that had dried and shrunk, (iii) direct injection of colloidal silica to a crack, (iv) injection of colloidal silica (CS) to wells in an overlying sand layer, (v) direct injection of polysiloxane to a crack, and (vi), injection of polysiloxane (PSX) to wells in an overlying soil layer

Nuclear Technology. Course 32: Nondestructive Examination (NDE) Techniques II. Module 32-4, Operation of Magnetic Particle Test Equipment.

Science.gov (United States)

Groseclose, Richard

This fourth in a series of six modules for a course titled Nondestructive Examination (NDE) Techniques II describes the specific technique variables and options which are available to the test technician, provides instructions for selecting and operating the appropriate test equipment, describes physical criteria for detectable discontinuities,…

Re-irradiation tests of spent fuel at JMTR by means of re-instrumentation technique

International Nuclear Information System (INIS)

Nakamura, Jinichi; Shimizu, Michio; Endo, Yasuichi; Nabeya, Hideaki; Ichise, Kenichi; Saito, Junichi; Oshima, Kunio; Uetsuka, Hiroshi

1999-01-01

JAERI has developed re-irradiation test procedures of spent fuel irradiated at commercial reactor by means of re-instrumentation technique. Full length rods irradiated at commercial LWRs were re-fabricated to short length rods, and rod inner pressure gauges and fuel center thermocouples were re-instrumented to the rods. Re-irradiation tests to study the fuel behavior during power change were carried out by means of BOCA/OSF-1 facility at the JMTR. In the tests to study the fission gas release during power change, the rod inner pressure increase was observed during power change, especially during power reduction. The fission gas release during power reduction is estimated to be the release from fission gas bubbles on the grain boundary caused by the thermal stress in the pellet during power reduction. Re-irradiation test of gadolinia added fuel was performed by means of dual re-instrumentation technique (fuel center thermocouples and rod inner pressure gauge). A stepwise fission gas release during power change, and the following fuel center temperature change due to gap conductance change were observed. (author)

Reliability of non-destructive test techniques in the inspection of pipelines used in the oil industry

International Nuclear Information System (INIS)

Carvalho, A.A.; Rebello, J.M.A.; Souza, M.P.V.; Sagrilo, L.V.S.; Soares, S.D.

2008-01-01

The aim of this work is to evaluate the reliability of non-destructive test (NDT) techniques for the inspection of pipeline welds employed in the petroleum industry. Radiography, manual and automatic ultrasonic techniques using pulse-echo and time of flight diffraction (TOFD) were employed. Three classes of defects were analyzed: lack of penetration (LP), lack of fusion (LF) and undercut (UC). The tests were carried out on specimen made from pipelines containing defects, which had been artificially inserted on laying the weld bead. The results showed the superiority of the automatic ultrasonic tests for defect detection compared with the manual ultrasonic and radiographic tests. Additionally, artificial neural networks (ANN) were used in the detection and automatic classification of the defects

POC-scale testing of an advanced fine coal dewatering equipment/technique

Energy Technology Data Exchange (ETDEWEB)

Groppo, J.G.; Parekh, B.K. [Univ. of Kentucky, Lexington, KY (United States); Rawls, P. [Department of Energy, Pittsburgh, PA (United States)

1995-11-01

Froth flotation technique is an effective and efficient process for recovering of ultra-fine (minus 74 {mu}m) clean coal. Economical dewatering of an ultra-fine clean coal product to a 20 percent level moisture will be an important step in successful implementation of the advanced cleaning processes. This project is a step in the Department of Energy`s program to show that ultra-clean coal could be effectively dewatered to 20 percent or lower moisture using either conventional or advanced dewatering techniques. As the contract title suggests, the main focus of the program is on proof-of-concept testing of a dewatering technique for a fine clean coal product. The coal industry is reluctant to use the advanced fine coal recovery technology due to the non-availability of an economical dewatering process. in fact, in a recent survey conducted by U.S. DOE and Battelle, dewatering of fine clean coal was identified as the number one priority for the coal industry. This project will attempt to demonstrate an efficient and economic fine clean coal slurry dewatering process.

Development of a Small Punch Test Technique for an Evaluation of the Mechanical Properties of Irradiated Materials in a Hot Cell

International Nuclear Information System (INIS)

Kim, Do-Sik; Ahn, Sang-Bok; Yoo, Byung-Ok; Choo, Yong-Sun; Hong, Kwon-Pyo

2006-01-01

Miniaturized specimens have been widely used to evaluate the mechanical properties of steels and plastics. Especially for a study on the irradiation effects in nuclear materials, the small specimen test techniques have attracted considerable attention. Therefore, it is essential that the test techniques be developed and verified to extract the mechanical properties information from small specimens. Among the test techniques using small specimens, the small punch (SP) test technique using small disc-sized specimen has been successfully used to estimate the tensile properties (yield strength and ultimate tensile strength), DBTT (ductile-brittle transition temperature), fracture toughness and creep properties of metals irradiated in a reactor or a proton accelerator. In this paper, the existing SP test techniques are reviewed and summarized. In addition, the information on the development of the SP test procedure is obtained to evaluate the radiation effects on the mechanical properties of nuclear materials in a hot cell

Cone penetrometer tests and HydroPunch sampling: A screening technique for plume definition

International Nuclear Information System (INIS)

Smolley, M.; Kappmeyer, J.C.

1991-01-01

Cone penetrometer tests and HydroPunch sampling were used to define the extent of volatile organic compounds in ground water. The investigation indicated that the combination of the these techniques is effective for obtaining ground water samples for preliminary plume definition. HydroPunch samples can be collected in unconsolidated sediments and the analytical results obtained from these samples are comparable to those obtained from adjacent monitoring wells. This sampling method is a rapid and cost-effective screening technique for characterizing the extent of contaminant plumes in soft sediment environments. Use of this screening technique allowed monitoring wells to be located at the plume boundary, thereby reducing the number of wells installed and the overall cost of the plume definition program

Techniques Employed to Conduct Postshot Drilling at the former Nevada Test Site

Energy Technology Data Exchange (ETDEWEB)

Dekin, W D

2011-04-14

Postshot drilling provided essential data on the results of the underground nuclear tests conducted at the Nevada Test Site (NTS), now identified as the Nevada National Security Site (NNSS). It was the means by which samples from the zone of interest were obtained for radiochemical analysis. This handbook describes how Lawrence Livermore National Laboratory (LLNL) conducted postshot drilling operations at the NTS, and it provides a general understanding of the process. Postshot drilling is a specialized application of rotary drilling. Accordingly, this handbook gives a brief description of rotary drilling in Section 2 to acquaint the reader with the general subject before proceeding to the specialized techniques used in postshot drilling. In Section 3, the handbook describes the typical postshot drilling situation at the former NTS and the drilling methods used. Section 4 describes the typical sequence of operations in postshot drilling at the former NTS. Detailed information on special equipment and techniques is given in a series of appendices (A through F) at the end of the handbook.

Neural Network Models of Simple Mechanical Systems Illustrating the Feasibility of Accelerated Life Testing

Science.gov (United States)

Fusaro, Robert L.; Jones, Steven P.; Jansen, Ralph

1996-01-01

A complete evaluation of the tribological characteristics of a given material/mechanical system is a time-consuming operation since the friction and wear process is extremely systems sensitive. As a result, experimental designs (i.e., Latin Square, Taguchi) have been implemented in an attempt to not only reduce the total number of experimental combinations needed to fully characterize a material/mechanical system, but also to acquire life data for a system without having to perform an actual life test. Unfortunately, these experimental designs still require a great deal of experimental testing and the output does not always produce meaningful information. In order to further reduce the amount of experimental testing required, this study employs a computer neural network model to investigate different material/mechanical systems. The work focuses on the modeling of the wear behavior, while showing the feasibility of using neural networks to predict life data. The model is capable of defining which input variables will influence the tribological behavior of the particular material/mechanical system being studied based on the specifications of the overall system.

Evaluation of deformation and fracture characteristics of nuclear reactor materials using ball indentation test technique

International Nuclear Information System (INIS)

Byun, T. S.; Hong, J. H.; Lee, B. S.; Park, D. G.; Kim, J. H.; Oh, Y. J.; Yoon, J. H.; Chi, S. H.; Kuk, I. H.; Kwon, D. I.; Lee, J. H.

1998-05-01

The present report describes the automated ball indentation test techniques and the results of their applications. The ball indentation test technique is an innovative method for evaluating the key mechanical properties from the indentation load-depth data. In the 1st chapter, the existing technique for evaluating basic deformation (tensile) properties is described in detail, and also the application result of the technique is presented. The through-thickness variations of mechanical properties in SA 508 C1.3 reactor pressure vessel steels were measured using an automated ball indentation (ABI) technique. In the 2nd chapter, a method under development, which is similar to that in the 1st chapter, is new method is based on the theoretical solutions rather than experimental relationships. The result of the application showed that the stress-strain curves of various metals were successfully determined with the method. In the 3rd chapter, a new theoretical model was proposed to estimate the fracture toughness of ferritic steels in the transition temperature region. The key concept of the model is that the indention energy to a critical load is related to the fracture energy of the material. The theory was applied to the reactor pressure vessel (RPV) base and weld metals. (author). 24 refs., 3 tabs., 6 figs

Layer-splitting technique for testing the recursive scheme for multilayer shields gamma ray buildup factors

International Nuclear Information System (INIS)

Alkhatib, Sari F.; Park, Chang Je; Jeong, Hae Yong; Lee, Yongdeok

2016-01-01

Highlights: • A simple formalism is suggested for the recursive approach and then it is used to produce buildup factors for certain multilayer shields. • The newly layer-splitting technique is implemented on the studied cases for testing the suggested formalism performance. • The buildup factors are generated using cubic polynomial fitting functions that are produced based on previous well-acknowledge data. - Abstract: This study illustrates the implementation of the newly suggested layer-splitting testing technique. This technique is introduced in order to be implemented in examining suggested formalisms for the recursive scheme (or iterative scheme). The recursive scheme is a concept used in treating and producing the gamma ray buildup factors in the case of multilayer shields. The layer-splitting technique simply enforces the scheme to treat a single layer of one material as two separated layers with similar characteristics. Thus it subjects the scheme to an abnormal definition of the multilayer shield that will test its performance in treating the successive layers. Thus, it will act as a method of verification for the approximations and assumptions taken in consideration. A simple formalism was suggested for the recursive scheme then the splitting technique was implemented on it. The results of implementing both the suggested formalism and the splitting technique are then illustrated and discussed. Throughout this study, cubic polynomial fitting functions were used to generate the data of buildup factors for the basic single-media that constitute the multilayer shields understudy. This study is limited to the cases of multiple shields consisting of repeated consecutive thin layers of lead–water and iron–water shields for 1 MeV gamma rays. The produced results of the buildup factor values through the implementation of the suggested formalism showed good consistency with the Monte Carlo simulation results of Lin and Jiang work. In the implementation of

Field Testing of Geophysical Techniques.

Science.gov (United States)

1981-11-01

influence drainage and groundwater movement in the surrounding area. Presumably, the direction of groundwater movement is to the north and out of the...applicable. Specifically, these additional techniques are: e Audio magneto- telluric (AMT) resistivity * Electromagnetics a Ground-probing radar Both

Combustion and emission based optimization of turbocharged diesel engine run on biodiesel using grey-taguchi method

International Nuclear Information System (INIS)

Masood, M.I.

2015-01-01

in this work it is attempted to optimize the combustion parameters such as instantaneous heal release (IR), cylinder Pressure (P) and rate of change oj pressure per degree crank angle (dP/do)) and the emissions characteristics such as NOx and Smoke of 2 turbocharged direct injection (DI) compression ignition (Cl) engine alternatively run on pure biodiesel (Bl 00), diesel and biodiesel-diesel blend (B20: applying Grey Taguchi method (GTM), GTM is used to convert multi variables into a single objective function The process environment comprising three input parameters (speed of the engine, load and type of fuel:, were used in this case, The design of experiment (DOE: was selected on an orthogonal array based on L9 (33) The Optimum Parameters were found on the basis ol Grey Relational Grade (GRG) and signal to noise (SN: ratio using GTM, The resulted optimum combination of the input parameters was used to get maximum possible values of IR, P and least possible values ol NOx, smoke and dP/do, The higher values of IH and I measure the better performance of the engine, while lower values of NO x' smoke and dP/do are the ultimate objectives of the study, According to the results It was revealed that B 1 00 fuel, 1800 rpm speed and 10% load offer the optimum combination for the desired performance of the engine along with reduced pollutants, Analysis of Variance (ANOVA) based on, software Minitab 16 was used to get the mos: significant input parameter keeping in view responses Fuel type and engine load were found to be the dominant factors with 48,16% and 43.18% impact or the output parameters, respectively, Finally the results were validated using Artificial Neural Network (ANN) through Mat lab. (author)

Testing of statistical techniques used in SYVAC

International Nuclear Information System (INIS)

Dalrymple, G.; Edwards, H.; Prust, J.

1984-01-01

Analysis of the SYVAC (SYstems Variability Analysis Code) output adopted four techniques to provide a cross comparison of their performance. The techniques used were: examination of scatter plots; correlation/regression; Kruskal-Wallis one-way analysis of variance by ranks; comparison of cumulative distribution functions and risk estimates between sub-ranges of parameter values. The analysis was conducted for the case of a single nuclide chain and was based mainly on simulated dose after 500,000 years. The results from this single SYVAC case showed that site parameters had the greatest influence on dose to man. The techniques of correlation/regression and Kruskal-Wallis were both successful and consistent in their identification of important parameters. Both techniques ranked the eight most important parameters in the same order when analysed for maximum dose. The results from a comparison of cdfs and risks in sub-ranges of the parameter values were not entirely consistent with other techniques. Further sampling of the high dose region is recommended in order to improve the accuracy of this method. (author)

Effect of injection parameters on mechanical and physical properties of super ultra-thin wall propylene packaging by Taguchi method

Science.gov (United States)

Ginghtong, Thatchanok; Nakpathomkun, Natthapon; Pechyen, Chiravoot

2018-06-01

The parameters of the plastic injection molding process have been investigated for the manufacture of a 64 oz. ultra-thin polypropylene bucket. The 3 main parameters, such as injection speed, melting temperature, holding pressure, were investigated to study their effect on the physical appearance and compressive strength. The orthogonal array of Taguchi's L9 (33) was used to carry out the experimental plan. The physical properties were measured and the compressive strength was determined using linear regression analysis. The differential scanning calorimeter (DSC) was used to analyze the crystalline structure of the product. The optimization results show that the proposed approach can help engineers identify optimal process parameters and achieve competitive advantages of energy consumption and product quality. In addition, the injection molding of the product includes 24 mm of shot stroke, 1.47 mm position transfer, 268 rpm screw speed, injection speed 100 mm/s, 172 ton clamping force, 800 kgf holding pressure, 0.9 s holding time and 1.4 s cooling time, make the products in the shape and proportion of the product satisfactory. The parameters of influence are injection speed 71.07%, melting temperature 23.31% and holding pressure 5.62%, respectively. The compressive strength of the product was able to withstand a pressure of up to 839 N before the product became plastic. The low melting temperature was caused by the superior crystalline structure of the super-ultra-thin wall product which leads to a lower compressive strength.

Suspension tests on a larger scale. Report from the status seminar on magnetic suspension techniques. Testing of the electrodynamic system started

Energy Technology Data Exchange (ETDEWEB)

Rogg, D; Muckli, W

1976-07-01

A world record speed for electromagnetically suspended vehicles as well as successful suspension tests with forced-circulation cooled superconducting magnets were the outstanding success reports at the fifth status seminar 'Magnetic suspension techniques' on 31st March and 1st April in Bad Kissingen. The research work on magnetic suspension techniques in the railborne long-distance travel is supported by the Federal Ministry of Research and Technology (BMFT) within the frameworke of the programme 'Railway engineering - New technologies'.

Author Details

African Journals Online (AJOL)

Mahapatra, S. Vol 2, No 5 (2010) - Articles Modeling, simulation and parametric optimization of wire EDM process using response surface methodology coupled with grey-Taguchi technique. Abstract PDF. ISSN: 2141-2839. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors ...

Application of positron annihilation techniques in non-destructive testing

International Nuclear Information System (INIS)

Zeng Hui; Chen Zhiqiang; Jiang Jing; Xue Xudong; Wu Yichu; Liang Jianping; Liu Xiangbing; Wang Rongshan

2014-01-01

Background: The investigation of the material damage state is very important for industrial application. Most mechanical damage starts with a change in the microstructure of the material. Positron annihilation techniques are very sensitive probes for detecting defects and damage on an atomic scale in materials, which are of great concern in the engineering applications. Additionally they are apparatus of non-destruction, high-sensitivity and easy-use. Purpose: Our goal is to develop a system to exploit new non-destructive testing (NDT) methods using positron annihilation spectroscopy, a powerful tool to detect vacancy-type defects and their chemical environment. Methods: A positron NDT system was designed and constructed by modifying the 'sandwich structure' of sample-source-sample in conventional Doppler broadening and positron lifetime spectrometers. Doppler broadening and positron lifetime spectra of a single sample can be measured and analyzed by subtracting the contribution of a reference sample. Results: The feasibility and reliability of positron NDT system have been tested by analyzing nondestructively deformation and damage caused by mechanical treatment or by irradiation of metal alloys. This system can be used for detecting defects and damage in thick or large-size samples, as well as for measuring the two-dimension distribution of defects in portable, sensitive, fast way. Conclusion: Positron NDT measurement shows changes in real atomic-scale defects prior to changes in the mechanical properties, which are detectable by other methods of NDT, such as ultrasonic testing and eddy current testing. This system can be developed for use in both the laboratory and field in the future. (authors)

Training Guidelines in Non-destructive Testing Techniques. 2013 Edition

International Nuclear Information System (INIS)

2014-12-01

The IAEA promotes industrial applications of radiation technology, including non-destructive testing (NDT), through activities such as Technical Cooperation Projects (national and regional) and Coordinated Research Projects. Through this cooperation, Member States have initiated national programmes for the training and certification of NDT personnel. National certifying bodies have also been established based on International Organization for Standardization (ISO) standards. As part of these efforts, the IAEA has been actively involved in developing training materials. Consequently, IAEA-TECDOC-407, Training Guidelines in Non-destructive Testing Techniques, was published in 1987, then revised and expanded as IAEA-TECDOC-628 in 1991. Revisions of IAEA-TECDOC-628 were considered essential to meet the demands of end-user industries in Member States, and revised and expanded versions were issued in 2002 and 2008. These latter versions included work conducted by the International Committee for Non-Destructive Testing (ICNDT) and many national NDT societies. It is one of the publications referred to in ISO 9712:2005, Non-destructive Testing: Qualification and Certification of Personnel, which in turn is an internationally accepted standard, revised as ISO 9712:2012, Non-destructive Testing: Qualification and Certification of NDT Personnel. This publication is an updated version of IAEA-TECDOC-628. The content of which has been revised following the changes of ISO 9712 converging with EN 473 and becoming EN ISO 9712:2012, based on the experience of experts and comments from end-user industries. The details of the topics on each subject have been expanded to include the latest developments in the respective methods. The incorporated changes will assist the end-user industries to update their NDT qualification and certification schemes and course materials. This publication, like the previous versions, will continue to play an important role in international harmonization

Refinement of the wedge bar technique for compression tests at intermediate strain rates

Directory of Open Access Journals (Sweden)

Stander M.

2012-08-01

Full Text Available A refined development of the wedge-bar technique [1] for compression tests at intermediate strain rates is presented. The concept uses a wedge mechanism to compress small cylindrical specimens at strain rates in the order of 10s−1 to strains of up to 0.3. Co-linear elastic impact principles are used to accelerate the actuation mechanism from rest to test speed in under 300μs while maintaining near uniform strain rates for up to 30 ms, i.e. the transient phase of the test is less than 1% of the total test duration. In particular, a new load frame, load cell and sliding anvil designs are presented and shown to significantly reduce the noise generated during testing. Typical dynamic test results for a selection of metals and polymers are reported and compared with quasistatic and split Hopkinson pressure bar results.

Accounting for estimated IQ in neuropsychological test performance with regression-based techniques.

Science.gov (United States)

Testa, S Marc; Winicki, Jessica M; Pearlson, Godfrey D; Gordon, Barry; Schretlen, David J

2009-11-01

Regression-based normative techniques account for variability in test performance associated with multiple predictor variables and generate expected scores based on algebraic equations. Using this approach, we show that estimated IQ, based on oral word reading, accounts for 1-9% of the variability beyond that explained by individual differences in age, sex, race, and years of education for most cognitive measures. These results confirm that adding estimated "premorbid" IQ to demographic predictors in multiple regression models can incrementally improve the accuracy with which regression-based norms (RBNs) benchmark expected neuropsychological test performance in healthy adults. It remains to be seen whether the incremental variance in test performance explained by estimated "premorbid" IQ translates to improved diagnostic accuracy in patient samples. We describe these methods, and illustrate the step-by-step application of RBNs with two cases. We also discuss the rationale, assumptions, and caveats of this approach. More broadly, we note that adjusting test scores for age and other characteristics might actually decrease the accuracy with which test performance predicts absolute criteria, such as the ability to drive or live independently.

Jsub(Ic)-testing of A-533 B - statistical evaluation of some different testing techniques

International Nuclear Information System (INIS)

Nilsson, F.

1978-01-01

The purpose of the present study was to compare statistically some different methods for the evaluation of fracture toughness of the nuclear reactor material A-533 B. Since linear elastic fracture mechanics is not applicable to this material at the interesting temperature (275 0 C), the so-called Jsub(Ic) testing method was employed. Two main difficulties are inherent in this type of testing. The first one is to determine the quantity J as a function of the deflection of the three-point bend specimens used. Three different techniques were used, the first two based on the experimentally observed input of energy to the specimen and the third employing finite element calculations. The second main problem is to determine the point when crack growth begins. For this, two methods were used, a direct electrical method and the indirect R-curve method. A total of forty specimens were tested at two laboratories. No statistically significant different results were obtained from the respective laboratories. The three methods of calculating J yielded somewhat different results, although the discrepancy was small. Also the two methods of determination of the growth initiation point yielded consistent results. The R-curve method, however, exhibited a larger uncertainty as measured by the standard deviation. The resulting Jsub(Ic) value also agreed well with earlier presented results. The relative standard deviation was of the order of 25%, which is quite small for this type of experiment. (author)

Testing remotely operated module technique for Wackersdorf reprocessing plant at Lahde test rig

International Nuclear Information System (INIS)

Leister, P.; Schroeder, G.; Boehme, G.

1986-01-01

The FEMO technique represents a plant concept which makes it possible to carry out the repair of high and medium activity wet chemical stages of the process by remote handling without direct access by staff. For this purpose, the apparatus of this step of the process is arranged modularly in large cells, so that movable large handling devices such as cranes and manipulator systems can replace process components subject to wear via the process modules. The machine room of the former coal-fired power station Heyden I at Lahde was, after removal of the turbines and generators, converted to a hall in which the following test areas were accommodated: FEMO cell section with 10 positions for module, cell wall mock-up and wall penetration, module mounting area, module measuring position, workplace for service area, training position, welding position and FEMO control position. (orig./HP) [de

Optimizing High Performance Self Compacting Concrete

Directory of Open Access Journals (Sweden)

Raymond A Yonathan

2017-01-01

Full Text Available This paper’s objectives are to learn the effect of glass powder, silica fume, Polycarboxylate Ether, and gravel to optimizing composition of each factor in making High Performance SCC. Taguchi method is proposed in this paper as best solution to minimize specimen variable which is more than 80 variations. Taguchi data analysis method is applied to provide composition, optimizing, and the effect of contributing materials for nine variable of specimens. Concrete’s workability was analyzed using Slump flow test, V-funnel test, and L-box test. Compressive and porosity test were performed for the hardened state. With a dimension of 100×200 mm the cylindrical specimens were cast for compressive test with the age of 3, 7, 14, 21, 28 days. Porosity test was conducted at 28 days. It is revealed that silica fume contributes greatly to slump flow and porosity. Coarse aggregate shows the greatest contributing factor to L-box and compressive test. However, all factors show unclear result to V-funnel test.

Flight Test Techniques

Science.gov (United States)

1989-01-01

the airframe for col1A 300 jauges pour un essal d𔄀preuve a ground "proof test" with a 0.8 charge, au sol A charge 0,8 recalant ce modile ; to update...the model. 200 among these 200 de ces jauges ont 6t6 cibl~es bonnes gauges had been wired to be "airworthy", de vol mats le domaine de vol a 4t6 but

TCV software test and validation tools and technique. [Terminal Configured Vehicle program for commercial transport aircraft operation

Science.gov (United States)

Straeter, T. A.; Williams, J. R.

1976-01-01

The paper describes techniques for testing and validating software for the TCV (Terminal Configured Vehicle) program which is intended to solve problems associated with operating a commercial transport aircraft in the terminal area. The TCV research test bed is a Boeing 737 specially configured with digital computer systems to carry out automatic navigation, guidance, flight controls, and electronic displays research. The techniques developed for time and cost reduction include automatic documentation aids, an automatic software configuration, and an all software generation and validation system.

Diminishing-cues retrieval practice: A memory-enhancing technique that works when regular testing doesn't.

Science.gov (United States)

Fiechter, Joshua L; Benjamin, Aaron S

2017-08-28

Retrieval practice has been shown to be a highly effective tool for enhancing memory, a fact that has led to major changes to educational practice and technology. However, when initial learning is poor, initial retrieval practice is unlikely to be successful and long-term benefits of retrieval practice are compromised or nonexistent. Here, we investigate the benefit of a scaffolded retrieval technique called diminishing-cues retrieval practice (Finley, Benjamin, Hays, Bjork, & Kornell, Journal of Memory and Language, 64, 289-298, 2011). Under learning conditions that favored a strong testing effect, diminishing cues and standard retrieval practice both enhanced memory performance relative to restudy. Critically, under learning conditions where standard retrieval practice was not helpful, diminishing cues enhanced memory performance substantially. These experiments demonstrate that diminishing-cues retrieval practice can widen the range of conditions under which testing can benefit memory, and so can serve as a model for the broader application of testing-based techniques for enhancing learning.

Development of Technique for Testing the Long-Term Stability of Silicon Microstrip Detectors

International Nuclear Information System (INIS)

Kosinov, A.V.; Maslov, N.I.; Naumov, S.V.; Ovchinnik, V.D.; Starodubtsev, A.F.; Vasiliev, G.P.; Yalovenko, V.I.; Bosisio, L.

2006-01-01

An automatic multi-channel set-up prototype for simultaneous testing of the Long-Term Stability (LTS) of more than ten detectors is described. The Inner Tracking System of the ALICE experiment will include about two thousand Double-sided Microstrip Detectors (DSMD). Efficient automatic measurement techniques are crucial for the LTS test, because the corresponding test procedure should be performed on each detector and requires long time, at least two days. By using special adapters for supporting and connecting the bare DSMDs, failing detectors can be screened out before module assembly, thus minimizing the cost. Automated probe stations developed for a special purpose or for microelectronics industry are used for measuring physical static DSMD characteristics and check good-to-bad elements ratio for DSMD. However, automated (or semi-automatic)test benches for studying LTS or testing DSMD long-term stability before developing a detecting module are absent

Study on interaction between palladium(ІІ)-Linezolid chelate with eosin by resonance Rayleigh scattering, second order of scattering and frequency doubling scattering methods using Taguchi orthogonal array design

Science.gov (United States)

Thakkar, Disha; Gevriya, Bhavesh; Mashru, R. C.

2014-03-01

Linezolid reacted with palladium to form 1:1 binary cationic chelate which further reacted with eosin dye to form 1:1 ternary ion association complex at pH 4 of Walpole's acetate buffer in the presence of methyl cellulose. As a result not only absorption spectra were changed but Resonance Rayleigh Scattering (RRS), Second-order Scattering (SOS) and Frequency Doubling Scattering (FDS) intensities were greatly enhanced. The analytical wavelengths of RRS, SOS and FDS (λex/λem) of ternary complex were located at 538 nm/538 nm, 240 nm/480 nm and 660 nm/330 nm, respectively. The linearity range for RRS, SOS and FDS methods were 0.01-0.5 μg mL-1, 0.1-2 μg mL-1 and 0.2-1.8 μg mL-1, respectively. The sensitivity order of three methods was as RRS > SOS > FDS. Accuracy of all methods were determined by recovery studies and showed recovery between 98% and 102%. Intraday and inter day precision were checked for all methods and %RSD was found to be less than 2 for all methods. The effects of foreign substances were tested on RRS method and it showed the method had good selectivity. For optimization of process parameter, Taguchi orthogonal array design L8(24) was used and ANOVA was adopted to determine the statistically significant control factors that affect the scattering intensities of methods. The reaction mechanism, composition of ternary ion association complex and reasons for scattering intensity enhancement was discussed in this work.

Multi-criteria decision making in the selection of machining parameters for Inconel 718

International Nuclear Information System (INIS)

Thirumalai, R.; Senthilkumaar, J. S.

2013-01-01

Taguchi's methods and design of experiments are invariably used and adopted as quality improvement techniques in several manufacturing industries as tools for offline quality control. These methods optimize single-response processes. However, Taguchi's method is not appropriate for optimizing a multi-response problem. In other situations, multi-responses need to be optimized simultaneously. This paper presents multi-response optimization techniques. A set of non-dominated solutions are obtained using non-sorted genetic algorithm for multi-objective functions. Multi-criteria decision making (MCDM) is proposed in this work for selecting a single solution from nondominated solutions. This paper addresses a new method of MCDM concept based on technique for order preference by similarity to ideal solution (TOPSIS). TOPSIS determines the shortest distance to the positive-ideal solution and the greatest distance from the negative-ideal solution. This work involves the high-speed machining of Inconel 718 using carbide cutting tool with six objective functions that are considered as attributes against the process variables of cutting speed, feed, and depth of cut. The higher-ranked solution is selected as the best solution for the machining of Inconel 718 in its respective environment.

Multi-criteria decision making in the selection of machining parameters for Inconel 718

Energy Technology Data Exchange (ETDEWEB)

Thirumalai, R. [SNS College of Technology, Coimbatore (India); Senthilkumaar, J. S. [Bharathithasan Engineering College, Nattrampalli (India)

2013-04-15

Taguchi's methods and design of experiments are invariably used and adopted as quality improvement techniques in several manufacturing industries as tools for offline quality control. These methods optimize single-response processes. However, Taguchi's method is not appropriate for optimizing a multi-response problem. In other situations, multi-responses need to be optimized simultaneously. This paper presents multi-response optimization techniques. A set of non-dominated solutions are obtained using non-sorted genetic algorithm for multi-objective functions. Multi-criteria decision making (MCDM) is proposed in this work for selecting a single solution from nondominated solutions. This paper addresses a new method of MCDM concept based on technique for order preference by similarity to ideal solution (TOPSIS). TOPSIS determines the shortest distance to the positive-ideal solution and the greatest distance from the negative-ideal solution. This work involves the high-speed machining of Inconel 718 using carbide cutting tool with six objective functions that are considered as attributes against the process variables of cutting speed, feed, and depth of cut. The higher-ranked solution is selected as the best solution for the machining of Inconel 718 in its respective environment.

Project GRETE: evaluation of non destructive testing techniques for monitoring of material degradation

International Nuclear Information System (INIS)

Coste, J.F.

2001-01-01

The material aging of major critical components of nuclear installations due to in-service conditions may lead to a degradation of their mechanical characteristics. The early detection of material changes and their monitoring using innovative non destructive testing techniques would allow to plan actions in order to prevent the apparition of macroscopic damage (e.g. cracks). One major difficulty in using these particular techniques is to correlate the changes in the measured NDT signals to the microstructural changes in the material due to aging. This problem may be solved through careful microstructural examinations of the material damage. The objective of the project GRETE is to illustrate the potential use of NDT techniques for the monitoring of material degradation through two examples: neutron irradiation of reactor pressure vessel steel and thermal fatigue of piping. The purpose of this paper is to present the project and its programme of work. (author)

Cold crucible technique for interaction test of molten corium with structure

International Nuclear Information System (INIS)

Ha, Kwang Soon; An, Sang Mo; Min, Beong Tae; Kim, Hwan Yeol

2012-01-01

During a severe accident, the molten corium might interact with several structures in a nuclear power plant such as core peripheral structures, lower plenum, lower head vessel, and external structures of a reactor vessel. The interaction of the molten corium with the structure depends on the molten corium composition, temperature, structural materials, and environmental conditions such as pressure and humidity. For example, the interaction of a metallic molten corium containing metal uranium (U) and zirconium (Zr) with the oxidized steel structure (Fe 2O3 ) is affected by not only thermal ablation but oxidation reduction reaction because the oxidation quotients of the U and Zr are higher than that of Fe. KAERI set up an experimental facility and technique using a cold crucible melting method to verify the interaction mechanism between the metallic molten corium and structural materials. This technique includes the generation of the metallic melt, melt delivery, measurement of the interaction process, and post analyses after the test

Test description and preliminary pitot-pressure surveys for Langley Test Technique Demonstrator at Mach 6

Science.gov (United States)

Everhart, Joel L.; Ashby, George C., Jr.; Monta, William J.

1992-01-01

A propulsion/airframe integration experiment conducted in the NASA Langley 20-Inch Mach 6 Tunnel using a 16.8-in.-long version of the Langley Test Technique Demonstrator configuration with simulated scramjet propulsion is described. Schlieren and vapor screen visualization of the nozzle flow field is presented and correlated with pitot-pressure flow-field surveys. The data were obtained at nominal free-stream conditions of Re = 2.8 x 10 exp 6 and a nominal engine total pressure of 100 psia. It is concluded that pitot-pressure surveys coupled to schlieren and vapor-screen photographs, and oil flows have revealed flow features including vortices, free shear layers, and shock waves occurring in the model flow field.

Impacts of environmental factors on arsenate biotransformation and release in Microcystis aeruginosa using the Taguchi experimental design approach.

Science.gov (United States)

Wang, Zhenhong; Luo, Zhuanxi; Yan, Changzhou; Xing, Baoshan

2017-07-01

Very limited information is available on how and to what extent environmental factors influence arsenic (As) biotransformation and release in freshwater algae. These factors include concentrations of arsenate (As(V)), dissolved inorganic nitrogen (N), phosphate (P), and ambient pH. This study conducted a series of experiments using Taguchi methods to determine optimum conditions for As biotransformation. We assessed principal effective factors of As(V), N, P, and pH and determined that As biotransformation and release actuate at 10.0 μM As(V) in dead alga cells, the As efflux ratio and organic As efflux content actuate at 1.0 mg/L P, algal growth and intracellular arsenite (As(III)) content actuate at 10.0 mg/L N, and the total sum of As(III) efflux from dead alga cells actuates at a pH level of 10. Moreover, N is the critical component for As(V) biotransformation in M. aeruginosa, specifically for As(III) transformation, because N can accelerate algal growth, subsequently improving As(III) accumulation and its efflux, which results in an As(V) to As(III) reduction. Furthermore, low P concentrations in combination with high N concentrations promote As accumulation. Following As(V), P was the primary impacting factor for As accumulation. In addition, small amounts of As accumulation under low concentrations of As and high P were securely stored in living algal cells and were easily released after cell death. Results from this study will help to assess practical applications and the overall control of key environmental factors, particularly those associated with algal bioremediation in As polluted water. Copyright © 2017 Elsevier Ltd. All rights reserved.

Opportunities and applications of medical imaging and image processing techniques for nondestructive testing

International Nuclear Information System (INIS)

Song, Samuel Moon Ho; Cho, Jung Ho; Son, Sang Rock; Sung, Je Jonng; Ahn, Hyung Keun; Lee, Jeong Soon

2002-01-01

Nondestructive testing (NDT) of structures strives to extract all relevant data regarding the state of the structure without altering its form or properties. The success enjoyed by imaging and image processing technologies in the field of modem medicine forecasts similar success of image processing related techniques both in research and practice of NDT. In this paper, we focus on two particular instances of such applications: a modern vision technique for 3-D profile and shape measurement, and ultrasonic imaging with rendering for 3-D visualization. Ultrasonic imaging of 3-D structures for nondestructive evaluation purposes must provide readily recognizable 3-D images with enough details to clearly show various faults that may or may not be present. As a step towards Improving conspicuity and thus detection of faults, we propose a pulse-echo ultrasonic imaging technique to generate a 3-D image of the 3-D object under evaluation through strategic scanning and processing of the pulse-echo data. This three-dimensional processing and display improves conspicuity of faults and in addition, provides manipulation capabilities, such as pan and rotation of the 3-D structure. As a second application, we consider an image based three-dimensional shape determination system. The shape, and thus the three-dimensional coordinate information of the 3-D object, is determined solely from captured images of the 3-D object from a prescribed set of viewpoints. The approach is based on the shape from silhouette (SFS) technique and the efficacy of the SFS method is tested using a sample data set. This system may be used to visualize the 3-D object efficiently, or to quickly generate initial CAD data for reverse engineering purposes. The proposed system potentially may be used in three dimensional design applications such as 3-D animation and 3-D games.

Parameters and definitions in applied technique quality test for nuclear magnetic resonance imaging system (NMRI)

International Nuclear Information System (INIS)

Lin Zhikai; Zhao Lancai

1999-08-01

During the past two decades, medical diagnostic imaging technique has achieved dramatic development such as CT, MRI, PET, DSA and so on. The most striking examples of them are the application of X ray computerized tomography (CT) and magnetic resonance imaging in the field of medical diagnosis. It can be predicted that magnetic resonance imaging (MRI) will definitely have more widespread prospects of applications and play more and more important role in clinical diagnosis looking forward to the development of image diagnostic technique for 21 st century. The authors also present the measuring methods for some parameters. The parameters described can be used for reference by clinical diagnosticians, operators on MRI and medical physicists who engages in image quality assurance (QA) and control (QC) in performing MRI acceptance test and routine test

Processing techniques for data from the Kuosheng Unit 1 shakedown safety-relief-valve tests

International Nuclear Information System (INIS)

McCauley, E.W.; Rompel, S.L.; Weaver, H.J.; Altenbach, T.J.

1982-08-01

This report describes techniques developed at the Lawrence Livermore National Laobratory, Livermore, CA for processing original data from the Taiwan Power Company's Kuosheng MKIII Unit 1 Safety Relief Valve Shakedown Tests conducted in April/May 1981. The computer codes used, TPSORT, TPPLOT, and TPPSD, form a special evaluation system for treating the data from its original packed binary form to ordered, calibrated ASCII transducer files and then to production of time-history plots, numerical output files, and spectral analyses. Using the data processing techniques described, a convenient means of independently examining and analyzing a unique data base for steam condensation phenomena in the MARKIII wetwell is described. The techniques developed for handling these data are applicable to the treatment of similar, but perhaps differently structured, experiment data sets

Assessment of mechanical and three-body abrasive wear peculiarity ...

Indian Academy of Sciences (India)

The three-body abrasive wear characteristic of fabricated composites has been assessed under different operating conditions. For this, the three-body abrasion test is done on dry abrasion test rig (TR-50)and analysed using Taguchi's experimental design scheme and analysis of variance. The results obtained from these ...

Optimization of Robotic Spray Painting process Parameters using Taguchi Method

Science.gov (United States)

Chidhambara, K. V.; Latha Shankar, B.; Vijaykumar

2018-02-01

Automated spray painting process is gaining interest in industry and research recently due to extensive application of spray painting in automobile industries. Automating spray painting process has advantages of improved quality, productivity, reduced labor, clean environment and particularly cost effectiveness. This study investigates the performance characteristics of an industrial robot Fanuc 250ib for an automated painting process using statistical tool Taguchi’s Design of Experiment technique. The experiment is designed using Taguchi’s L25 orthogonal array by considering three factors and five levels for each factor. The objective of this work is to explore the major control parameters and to optimize the same for the improved quality of the paint coating measured in terms of Dry Film thickness(DFT), which also results in reduced rejection. Further Analysis of Variance (ANOVA) is performed to know the influence of individual factors on DFT. It is observed that shaping air and paint flow are the most influencing parameters. Multiple regression model is formulated for estimating predicted values of DFT. Confirmation test is then conducted and comparison results show that error is within acceptable level.

Air leakage test of reactor hall using tracer technique

International Nuclear Information System (INIS)

Yang Yanqiu; Yang Liang; Yang Tongzai

2011-01-01

The leakage ratios of three related reactor halls were tested by sulfur hexafluoride gaseous tracer technique. Moreover, the accumulation intensities of leak gas and its retention time in some important working rooms, the crossroads of corridors and anteroom of the building were detected. The results show that the air leakage ratios of the three reactor halls are (7.30±0.16) x 10 -4 , (1.88±0.12) x 10 -4 and (2.07±0.07) x 10 -4 h -1 . The leak gas accumulates in all the detected working rooms fast, and the retention time to various rooms is about 5 h. The heaviest intensities are in the clothes change rooms on the first floor. However, the retention time to the crossroads and the anteroom is about 10 h, and the accumulation intensities are much small. (authors)

The comparison of bolus tracking and test bolus techniques for computed tomography thoracic angiography in healthy beagles

Directory of Open Access Journals (Sweden)

Nicolette Cassel

2013-05-01

Full Text Available Computed tomography thoracic angiography studies were performed on five adult beagles using the bolus tracking (BT technique and the test bolus (TB technique, which were performed at least two weeks apart. For the BT technique, 2 mL/kg of 300 mgI/mL iodinated contrast agent was injected intravenously. Scans were initiated when the contrast in the aorta reached 150 Hounsfield units (HU. For the TB technique, the dogs received a test dose of 15% of 2 mL/kg of 300 mgI/mL iodinated contrast agent, followed by a series of low dose sequential scans. The full dose of the contrast agent was then administered and the scans were conducted at optimal times as identified from time attenuation curves. Mean attenuation in HU was measured in the aorta (Ao and right caudal pulmonary artery (rCPA. Additional observations included the study duration, milliAmpere (mA, computed tomography dose index volume (CTDI[vol] and dose length product (DLP. The attenuation in the Ao (BT = 660 52 HU ± 138 49 HU, TB = 469 82 HU ± 199 52 HU, p = 0.13 and in the rCPA (BT = 606 34 HU ± 143 37 HU, TB = 413 72 HU ± 174.99 HU, p = 0.28 did not differ significantly between the two techniques. The BT technique was conducted in a significantly shorter time period than the TB technique (p = 0.03. The mean mA for the BT technique was significantly lower than the TB technique (p = 0.03, as was the mean CTDI(vol (p = 0.001. The mean DLP did not differ significantly between the two techniques (p = 0.17. No preference was given to either technique when evaluating the Ao or rCPA but the BT technique was shown to be shorter in duration and resulted in less DLP than the TB technique.

Optimum Combination and Effect Analysis of Piezoresistor Dimensions in Micro Piezoresistive Pressure Sensor Using Design of Experiments and ANOVA: a Taguchi Approach

Directory of Open Access Journals (Sweden)

Kirankumar B. Balavalad

2017-04-01

Full Text Available Piezoresistive (PZR pressure sensors have gained importance because of their robust construction, high sensitivity and good linearity. The conventional PZR pressure sensor consists of 4 piezoresistors placed on diaphragm and are connected in the form of Wheatstone bridge. These sensors convert stress applied on them into change in resistance, which is quantified into voltage using Wheatstone bridge mechanism. It is observed form the literature that, the dimensions of piezoresistors are very crucial in the performance of the piezoresistive pressure sensor. This paper presents, a novel mechanism of finding best combinations and effect of individual piezoresistors dimensions viz., Length, Width and Thickness, using DoE and ANOVA (Analysis of Variance method, following Taguchi experimentation approach. The paper presents a unique method to find optimum combination of piezoresistors dimensions and also clearly illustrates the effect the dimensions on the output of the sensor. The optimum combinations and the output response of sensor is predicted using DoE and the validation simulation is done. The result of the validation simulation is compared with the predicted value of sensor response i.e., V. Predicted value of V is 1.074 V and the validation simulation gave the response for V as 1.19 V. This actually validates that the model (DoE and ANOVA is adequate in describing V in terms of the variables defined.

Features of application of test techniques in selection and certification of personnel

Directory of Open Access Journals (Sweden)

Levina E.V.

2017-04-01

Full Text Available this article investigates the problem of use of test techniques in the course of selection and certification of personnel, and also for detection of features of formation of social and psychological climate in small groups and labor collectives. The group dynamics including individual preferences of players in the choice of strategy of behavior in a conflict situation in definition of the most acceptable social role, in identification of the most constructive and effective type of the administrative decision has the special importance. The author of the article offers a set of the test methods allowing to define social and psychological type of the individual at a stage of staff recruitment and to reveal its individual behavioral preferences that can structurally influence on team work.

Some problems in the technique of high-voltage testing of the accelerating tube gaps in electrostatic accelerators

International Nuclear Information System (INIS)

Romanov, V.A.; Ivanov, V.V.; Mukhametshin, V.I.; Dmitriev, E.P.; Kidalov, A.I.

1983-01-01

Problems arising during high-voltage testing and training of accelerating taubes of electrostatic accelrators are discussed. A rig and technique of the accelerating tube testing and program designed for the processing of the data obtained and sorting out of the samples investigated are described

Software tool for resolution of inverse problems using artificial intelligence techniques: an application in neutron spectrometry

International Nuclear Information System (INIS)

Castaneda M, V. H.; Martinez B, M. R.; Solis S, L. O.; Castaneda M, R.; Leon P, A. A.; Hernandez P, C. F.; Espinoza G, J. G.; Ortiz R, J. M.; Vega C, H. R.; Mendez, R.; Gallego, E.; Sousa L, M. A.

2016-10-01

The Taguchi methodology has proved to be highly efficient to solve inverse problems, in which the values of some parameters of the model must be obtained from the observed data. There are intrinsic mathematical characteristics that make a problem known as inverse. Inverse problems appear in many branches of science, engineering and mathematics. To solve this type of problem, researches have used different techniques. Recently, the use of techniques based on Artificial Intelligence technology is being explored by researches. This paper presents the use of a software tool based on artificial neural networks of generalized regression in the solution of inverse problems with application in high energy physics, specifically in the solution of the problem of neutron spectrometry. To solve this problem we use a software tool developed in the Mat Lab programming environment, which employs a friendly user interface, intuitive and easy to use for the user. This computational tool solves the inverse problem involved in the reconstruction of the neutron spectrum based on measurements made with a Bonner spheres spectrometric system. Introducing this information, the neural network is able to reconstruct the neutron spectrum with high performance and generalization capability. The tool allows that the end user does not require great training or technical knowledge in development and/or use of software, so it facilitates the use of the program for the resolution of inverse problems that are in several areas of knowledge. The techniques of Artificial Intelligence present singular veracity to solve inverse problems, given the characteristics of artificial neural networks and their network topology, therefore, the tool developed has been very useful, since the results generated by the Artificial Neural Network require few time in comparison to other techniques and are correct results comparing them with the actual data of the experiment. (Author)

Complexity testing techniques for time series data: A comprehensive literature review

International Nuclear Information System (INIS)

Tang, Ling; Lv, Huiling; Yang, Fengmei; Yu, Lean

2015-01-01

Highlights: • A literature review of complexity testing techniques for time series data is provided. • Complexity measurements can generally fall into fractality, methods derived from nonlinear dynamics and entropy. • Different types investigate time series data from different perspectives. • Measures, applications and future studies for each type are presented. - Abstract: Complexity may be one of the most important measurements for analysing time series data; it covers or is at least closely related to different data characteristics within nonlinear system theory. This paper provides a comprehensive literature review examining the complexity testing techniques for time series data. According to different features, the complexity measurements for time series data can be divided into three primary groups, i.e., fractality (mono- or multi-fractality) for self-similarity (or system memorability or long-term persistence), methods derived from nonlinear dynamics (via attractor invariants or diagram descriptions) for attractor properties in phase-space, and entropy (structural or dynamical entropy) for the disorder state of a nonlinear system. These estimations analyse time series dynamics from different perspectives but are closely related to or even dependent on each other at the same time. In particular, a weaker self-similarity, a more complex structure of attractor, and a higher-level disorder state of a system consistently indicate that the observed time series data are at a higher level of complexity. Accordingly, this paper presents a historical tour of the important measures and works for each group, as well as ground-breaking and recent applications and future research directions.

Nuclear Technology. Course 26: Nondestructive Examination (NDE) Techniques I. Module 26-3, Hydrostatic Tests.

Science.gov (United States)

Pelton, Rick; Espy, John

This third in a series of seven modules for a course titled Nondestructive Examination (NDE) Techniques I describes the principles and practices associated with hydrostatic testing. The module follows a typical format that includes the following sections: (1) introduction, (2) module prerequisites, (3) objectives, (4) notes to instructor/student,…

Application of acoustic emission, as non destructive testing technique, to nuclear components inspection

International Nuclear Information System (INIS)

Sanchez Miro, J.J.

1980-01-01

A panorama of actual state of acoustic emission as non destructive testing technique, from stand point of its safety applications to nuclear reactor is offered. In first place the physic grounds of acoustic emission phenomenon is briefly exposed. After we speak about the experimental methods for detection, and overall is made an explanation of the problems which are found during the application of this technology to on-line inspection of nuclear oower plants. It is hoped that this repport makes a contribution in the sense of to create a favourable atmosphere toward the introduction in our country of this important technique, and concretely within the nuclear power industry. In this last field the employ of acoustic emission is overcoming the experimental stage. (author)

Study on corrosion test techniques in lead bismuth eutectic flow. Joint research report in JFY2002

International Nuclear Information System (INIS)

Takahashi, Minoru; Sekimoto, Hiroshi

2003-03-01

The evaluation of corrosion behaviors of core and structural materials in lead bismuth eutectic is one of the key issues for the utilization of lead bismuth eutectic as a coolant of the primary loops of lead bismuth cooled fast breeder reactors (FBRs) and the intermediate heat transport media of new-type steam generators of the sodium cooled FBRs. The purpose of the present study is to establish corrosion test techniques in lead bismuth eutectic flow. The techniques of steel corrosion test and oxygen control in flowing lead bismuth eutectic, and the technologies of a lead bismuth flow test at high temperature and high velocity were developed through corrosion test using a lead bismuth flow test loop of the Tokyo Institute of Technology in JFY2002. The major results are summarized as follows: (1) Techniques of fabrication, mount and rinse of corrosion specimens, measurement method of weight loss, and SEM/EDX analysis method have been established through lead bismuth corrosion test. (2) Weight losses were measured, corrosion and lead bismuth-adhered layers and eroded parts were observed in two 1000 hr-corrosion tests, and the results were compared with each other for twelve existing steels including ODS, F82H and SUH-3. (3) An oxygen sensor made of zirconia electrolyte structurally resistant to thermal stress and thermal shock was developed and tested in the lead bismuth flow loop. Good performance has been obtained. (4) An oxygen control method by injecting argon and hydrogen mixture gas containing steam into lead bismuth was applied to the lead bismuth flow loop, and technical issues for the development of the oxygen control method were extracted. (5) Technical measures for freezing and leakage of lead bismuth in the flow loop were accumulated. (6) Technical measures for flow rate decrease/blockage due to precipitation of oxide and corrosion products in a low temperature section of the lead bismuth flow loop were accumulated. (7) Electromagnetic flow meters with MI

Tests of heat techniques in households. Analysis of the results of the field tests; Praktijkprestaties van warmtetechnieken bij huishoudens. Analyse resultaten veldtesten

Energy Technology Data Exchange (ETDEWEB)

De Jong, A.; Friedel, P.; Overman, P. [Energy Matters, Driebergen (Netherlands)

2012-11-15

The development within conventional techniques and new techniques for the recovery and generation of heat in the house construction industry led to a need for knowledge of efficiencies of those techniques in practice. Therefore a project has been set up to gain insight into the efficiencies. In the field tests, five heat techniques are investigated: high-efficiency boilers, solar water heaters, balanced ventilation systems with heat recovery (also called heat recovery systems) and heat pump water heaters [Dutch] De ontwikkeling binnen conventionele technieken en nieuwe technieken voor de terugwinning en opwekking van warmte in de woningbouw leidden ertoe dat er bij verschillende partijen in de keten een kennisbehoefte is ontstaan naar de rendementen van deze technieken in de praktijk. Daartoe heeft AgentschapNL een project opgezet om meer inzicht te verkrijgen in deze rendementen. In de veldtesten worden vijf warmtechnieken bekeken: HR-ketels, HRe-ketels, zonneboilers, gebalanceerde ventilatiesystemen met warmteterugwinning (verder WTW-systemen genoemd) en warmtepompboilers. Deze worden op minutenbasis bemeten.

Testing of indoor radon reduction techniques in eastern Pennsylvania: An update

International Nuclear Information System (INIS)

Henschel, D.B.; Scott, A.G.

1987-01-01

EPA has installed radon reduction measures in 38 houses in the Reading Prong region of eastern Pennsylvania. All were basement houses with hollow block or poured concrete foundation walls. The reduction approaches tested in most houses involved active soil ventilation, including: suction on the footing drain tile system; suction underneath the concrete slabs, using pipes inserted through the slabs from inside the house; and ventilation of the void network inside hollow block foundation walls. Heat recovery ventilators (HRVs) were tested in three houses. The current results confirm that, for the houses tested here, drain tile suction appears consistently able to provide high radon reductions when a complete loop of drain tile exists, often reducing high-radon houses to 4 pCi/l (148 B1/m 3 ) and less. Sub-slab suction (with pipes through the slab) can also provide high reductions if a sufficient number of suction pipes are located properly. Placement of one or more sub-slab suction pipes near each perimeter wall appears in this testing to aid in treating the major soil gas entry routes, although fewer pipes can sometimes give high reductions if conditions are favorable. For effective radon reduction using any active soil ventilation technique, it is important that major wall and slab openings be closed, and that a fan be employed that is capable of developing adequate static pressure

Observation-Driven Configuration of Complex Software Systems

Science.gov (United States)

Sage, Aled

2010-06-01

The ever-increasing complexity of software systems makes them hard to comprehend, predict and tune due to emergent properties and non-deterministic behaviour. Complexity arises from the size of software systems and the wide variety of possible operating environments: the increasing choice of platforms and communication policies leads to ever more complex performance characteristics. In addition, software systems exhibit different behaviour under different workloads. Many software systems are designed to be configurable so that policies can be chosen to meet the needs of various stakeholders. For complex software systems it can be difficult to accurately predict the effects of a change and to know which configuration is most appropriate. This thesis demonstrates that it is useful to run automated experiments that measure a selection of system configurations. Experiments can find configurations that meet the stakeholders' needs, find interesting behavioural characteristics, and help produce predictive models of the system's behaviour. The design and use of ACT (Automated Configuration Tool) for running such experiments is described, in combination a number of search strategies for deciding on the configurations to measure. Design Of Experiments (DOE) is discussed, with emphasis on Taguchi Methods. These statistical methods have been used extensively in manufacturing, but have not previously been used for configuring software systems. The novel contribution here is an industrial case study, applying the combination of ACT and Taguchi Methods to DC-Directory, a product from Data Connection Ltd (DCL). The case study investigated the applicability of Taguchi Methods for configuring complex software systems. Taguchi Methods were found to be useful for modelling and configuring DC- Directory, making them a valuable addition to the techniques available to system administrators and developers.

Preparation and Application of a Nano α-Fe2O3/SAPO-34 Photocatalyst for Removal of the Anti-cancer Drug Doxorubicin using the Taguchi Approach

Directory of Open Access Journals (Sweden)

Bigtan Mohammad Hosein

2016-01-01

Full Text Available The synthesis of α-Fe2O3/SAPO-34 nano photocatalyst was the first step of this study. The α-Fe2O3 nanocatalyst was synthesized applying forced hydrolysis and reflux condensation followed by solid-state dispersion that was used for supporting α-Fe2O3 on SAPO-34. The next step was a characterization of the catalyst that was performed using X-ray diffraction (XRD, scanning electron microscopy (SEM and Fourier Transform Infrared Spectroscopy (FT-IR. Then, for optimizing the operational parameters in Doxorubicin’s degradation process the effect of Doxorubicin concentration, the amount of α-Fe2O3/SAPO-34 nano photocatalyst, the pH, and H2O2 concentration was studied via the Taguchi method. The AL9 orthogonal array was adjusted and nine crucial runs were conducted. For calculating Signal/Noise ratio, each run was repeated three times. As the results showed, the concentration of Doxorubicin is the most effective parameter. Optimized conditions for removing the anti-cancer drug (based on Signal/Noise ratio were Doxorubicin concentration (20 ppm, H2O2 concentration (3 mol/L, catalyst amount (50 mg/L and pH = 8.

Strategi Perencanaan Jumlah Material Tambahan dalam Memproduksi Semen dengan Pendekatan Taguchi untuk Meminimalkan Biaya Produksi (Study Kasus PT Semen Padang

Directory of Open Access Journals (Sweden)

Nelvi Irawati

2016-04-01

Full Text Available Cement is a construction material with a specific quality that must be meet standard requirements and customer requirements. Through a good and continuous quality control, it will produce cement with consistent quality as its Quality Planning. Cement quality is calculated after adding water by measuring its setting time, compressive strength developing, the heat of hydration, expansion/shrinkage, and its durability to environment effect. In cement application, the primary parameter to determine cement quality is its compressive strength. Some factors that affect compressive strength of cement are reactivity and amount of Tricalcium Silicate (C3S of Clinker, Clinker free lime (free CaO, amount of SO3 in Cement, the amount of additional materials (insoluble residue/IR and loss on ignition/LOI, and sieve on 45 µm residue of cement. This research is intended to find how insoluble residue/IR, loss on ignition/LOI, and the amount of SO3 will affect compressive strength of cement. Various percentages of IR, LOI, and SO3 in cement will result in different compressive strength. Taguchi Method is applied to determine material proportion. With Orthogonal Array calculation for 3 factors and 4 levels, it will result in 16 calculation running times (L16 4**3. In laboratory scale, cement for this research has been being manufactured and then its compressive strength for 3 days, 7 days, and 28 days will be measured. Determination of optimal proportion will be calculated by statistic method for higher compressive strength and lower manufacturing cost.

The Design and Development of Test Platform for Wheat Precision Seeding Based on Image Processing Techniques

OpenAIRE

Li , Qing; Lin , Haibo; Xiu , Yu-Feng; Wang , Ruixue; Yi , Chuijie

2009-01-01

International audience; The test platform of wheat precision seeding based on image processing techniques is designed to develop the wheat precision seed metering device with high efficiency and precision. Using image processing techniques, this platform gathers images of seeds (wheat) on the conveyer belt which are falling from seed metering device. Then these data are processed and analyzed to calculate the qualified rate, reseeding rate and leakage sowing rate, etc. This paper introduces t...

Cyclic Testing of the 6-Strand Tang and Modified Lim-Tsai Flexor Tendon Repair Techniques.

Science.gov (United States)

Kang, Gavrielle Hui-Ying; Wong, Yoke-Rung; Lim, Rebecca Qian-Ru; Loke, Austin Mun-Kitt; Tay, Shian-Chao

2018-03-01

In this study, we compared the Tang repair technique with the 6-strand modified Lim-Tsai repair technique under cyclic testing conditions. Twenty fresh-frozen porcine flexor tendons were randomized into 2 groups for repair with either the modified Lim-Tsai or the Tang technique using Supramid 4-0 core sutures and Ethilon 6-0 epitendinous running suture. The repaired tendons were subjected to 2 stage cyclic loading. The survival rate and gap formation at the repair site were recorded. Tendons repaired by the Tang technique achieved an 80% survival rate. None of the modified Lim-Tsai repairs survived. The mean gap formed at the end of 1000 cycles was 1.09 mm in the Tang repairs compared with 4.15 mm in the modified Lim-Tsai repairs. The Tang repair is biomechanically stronger than the modified Lim-Tsai repair under cyclic loading. The Tang repair technique may exhibit a higher tolerance for active mobilization after surgery with less propensity for gap formation. Copyright © 2018 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

BLANK SHAPE OPTIMIZATION ON DEEP DRAWING OF A TWIN ELLIPTICAL CUP USING THE REDUCED BASIS TECHNIQUE METHOD

Directory of Open Access Journals (Sweden)

Mahdi Hasanzadeh Golshani

2015-08-01

Full Text Available In this project thesis, initial blank shape optimization of a twin elliptical cup to reduce earring phenomenon in anisotropic sheet deep drawing process was studied .The purpose of this study is optimization of initial blank for reduction of the ears height value. The optimization process carried out using finite element method approach, which is coupled with Taguchi design of experiments and reduced basis technique methods. The deep drawing process was simulated in FEM software ABAQUS 6.12. The results of optimization show earring height and, in addition, a number of design variables and time of process can be reduced by using this methods. After optimization process with the proposed method, the maximum reduction of the earring height would be from 21.08 mm to 0.07 mm and also it could be reduced to 0 in some of the directions. The proposed optimization design in this article allows the designers to select the practical basis shapes. This leads to obtain better results at the end of the optimization process, to reduce design variables, and also to prevent repeating the optimization steps for indirect shapes.

Evaluation of the Repeatability of the Delta Q Duct Leakage Testing TechniqueIncluding Investigation of Robust Analysis Techniques and Estimates of Weather Induced Uncertainty

Energy Technology Data Exchange (ETDEWEB)

Dickerhoff, Darryl; Walker, Iain

2008-08-01

The DeltaQ test is a method of estimating the air leakage from forced air duct systems. Developed primarily for residential and small commercial applications it uses the changes in blower door test results due to forced air system operation. Previous studies established the principles behind DeltaQ testing, but raised issues of precision of the test, particularly for leaky homes on windy days. Details of the measurement technique are available in an ASTM Standard (ASTM E1554-2007). In order to ease adoption of the test method, this study answers questions regarding the uncertainty due to changing weather during the test (particularly changes in wind speed) and the applicability to low leakage systems. The first question arises because the building envelope air flows and pressures used in the DeltaQ test are influenced by weather induced pressures. Variability in wind induced pressures rather than temperature difference induced pressures dominates this effect because the wind pressures change rapidly over the time period of a test. The second question needs to answered so that DeltaQ testing can be used in programs requiring or giving credit for tight ducts (e.g., California's Building Energy Code (CEC 2005)). DeltaQ modeling biases have been previously investigated in laboratory studies where there was no weather induced changes in envelope flows and pressures. Laboratory work by Andrews (2002) and Walker et al. (2004) found biases of about 0.5% of forced air system blower flow and individual test uncertainty of about 2% of forced air system blower flow. The laboratory tests were repeated by Walker and Dickerhoff (2006 and 2008) using a new ramping technique that continuously varied envelope pressures and air flows rather than taking data at pre-selected pressure stations (as used in ASTM E1554-2003 and other previous studies). The biases and individual test uncertainties for ramping were found to be very close (less than 0.5% of air handler flow) to those

Comparison of NDT techniques to evaluate CFRP. Results obtained in a MAIzfp round robin test

Energy Technology Data Exchange (ETDEWEB)

Grosse, Christian U. [Technische Univ. Muenchen (Germany). Chair of Non-destructive Testing; Goldammer, Matthias; Grager, Jan-Carl [Siemens AG Corporate Technology, Muenchen (Germany); and others

2016-10-01

Fiber reinforced polymeric materials are used for lightweight constructions and are an integral part of cars, airplanes or rotor blades of wind turbines. Nondestructive testing (NDT) methods play an increasing role concerning the manufacturing process and the inspection during lifetime. The selection of the best NDT technique for a certain application depends - of course - on many factors including the type, position and size of the defect to be detected but also on secondary issues like accessibility, automation, testing costs, reliability and resolution to mention only some. For the more technical-scientific part of these issues, the determination of the probability of detection (PoD) plays a significant role. Early in the design process questions should be raised concerning the probability with which certain attribute of interest (a defect that has an effect on the structural behavior) can be detected (and localized) in a certain construction. Several defect types have been identified to be critical like impact damages, undulations and porosity. Test samples out of differently processed Carbon Fiber-Reinforced Polymers (CFRP) as used in the automotive or aeronautical industry have been produced including defects of different type and size. In order to determine the PoD and to check whether a technique is applicable the different partners applied a broad variety of selected NDT techniques including Micro CT, Ultrasound (including phased-array and air-coupled UT), Active Thermography, Eddy Current, Vibration and Visual Analysis and Local Acoustic Resonance Spectroscopy (LARS). The presentation will summarize some of the results of the experiments and ongoing data analysis.

Comparison of NDT techniques to evaluate CFRP. Results obtained in a MAIzfp round robin test

International Nuclear Information System (INIS)

Grosse, Christian U.

2016-01-01

Fiber reinforced polymeric materials are used for lightweight constructions and are an integral part of cars, airplanes or rotor blades of wind turbines. Nondestructive testing (NDT) methods play an increasing role concerning the manufacturing process and the inspection during lifetime. The selection of the best NDT technique for a certain application depends - of course - on many factors including the type, position and size of the defect to be detected but also on secondary issues like accessibility, automation, testing costs, reliability and resolution to mention only some. For the more technical-scientific part of these issues, the determination of the probability of detection (PoD) plays a significant role. Early in the design process questions should be raised concerning the probability with which certain attribute of interest (a defect that has an effect on the structural behavior) can be detected (and localized) in a certain construction. Several defect types have been identified to be critical like impact damages, undulations and porosity. Test samples out of differently processed Carbon Fiber-Reinforced Polymers (CFRP) as used in the automotive or aeronautical industry have been produced including defects of different type and size. In order to determine the PoD and to check whether a technique is applicable the different partners applied a broad variety of selected NDT techniques including Micro CT, Ultrasound (including phased-array and air-coupled UT), Active Thermography, Eddy Current, Vibration and Visual Analysis and Local Acoustic Resonance Spectroscopy (LARS). The presentation will summarize some of the results of the experiments and ongoing data analysis.

Standard Test Method for Determining Thermal Neutron Reaction Rates and Thermal Neutron Fluence Rates by Radioactivation Techniques

CERN Document Server

American Society for Testing and Materials. Philadelphia

2008-01-01

1.1 The purpose of this test method is to define a general procedure for determining an unknown thermal-neutron fluence rate by neutron activation techniques. It is not practicable to describe completely a technique applicable to the large number of experimental situations that require the measurement of a thermal-neutron fluence rate. Therefore, this method is presented so that the user may adapt to his particular situation the fundamental procedures of the following techniques. 1.1.1 Radiometric counting technique using pure cobalt, pure gold, pure indium, cobalt-aluminum, alloy, gold-aluminum alloy, or indium-aluminum alloy. 1.1.2 Standard comparison technique using pure gold, or gold-aluminum alloy, and 1.1.3 Secondary standard comparison techniques using pure indium, indium-aluminum alloy, pure dysprosium, or dysprosium-aluminum alloy. 1.2 The techniques presented are limited to measurements at room temperatures. However, special problems when making thermal-neutron fluence rate measurements in high-...

Role of omics techniques in the toxicity testing of nanoparticles

Directory of Open Access Journals (Sweden)

Eleonore Fröhlich

2017-11-01

Full Text Available Abstract Nanotechnology is regarded as a key technology of the twenty-first century. Despite the many advantages of nanotechnology it is also known that engineered nanoparticles (NPs may cause adverse health effects in humans. Reports on toxic effects of NPs relay mainly on conventional (phenotypic testing but studies of changes in epigenome, transcriptome, proteome, and metabolome induced by NPs have also been performed. NPs most relevant for human exposure in consumer, health and food products are metal, metal oxide and carbon-based NPs. They were also studied quite frequently with omics technologies and an overview of the study results can serve to answer the question if screening for established targets of nanotoxicity (e.g. cell death, proliferation, oxidative stress, and inflammation is sufficient or if omics techniques are needed to reveal new targets. Regulated pathways identified by omics techniques were confirmed by phenotypic assays performed in the same study and comparison of particle types and cells by the same group indicated a more cell/organ-specific than particle specific regulation pattern. Between different studies moderate overlap of the regulated pathways was observed and cell-specific regulation is less obvious. The lack of standardization in particle exposure, in omics technologies, difficulties to translate mechanistic data to phenotypes and comparison with human in vivo data currently limit the use of these technologies in the prediction of toxic effects by NPs.

Evaluation of J-R curve testing of nuclear piping materials using the direct current potential drop technique

International Nuclear Information System (INIS)

Hackett, E.M.; Kirk, M.T.; Hays, R.A.

1986-08-01

A method is described for developing J-R curves for nuclear piping materials using the DC Potential Drop (DCPD) technique. Experimental calibration curves were developed for both three point bend and compact specimen geometries using ASTM A106 steel, a type 304 stainless steel and a high strength aluminum alloy. These curves were fit with a power law expression over the range of crack extension encountered during J-R curve tests (0.6 a/W to 0.8 a/W). The calibration curves were insensitive to both material and sidegrooving and depended solely on specimen geometry and lead attachment points. Crack initiation in J-R curve tests using DCPD was determined by a deviation from a linear region on a plot of COD vs. DCPD. The validity of this criterion for ASTM A106 steel was determined by a series of multispecimen tests that bracketed the initiation region. A statistical differential slope procedure for determination of the crack initiation point is presented and discussed. J-R curve tests were performed on ASTM A106 steel and type 304 stainless steel using both the elastic compliance and DCPD techniques to assess R-curve comparability. J-R curves determined using the two approaches were found to be in good agreement for ASTM A106 steel. The applicability of the DCPD technique to type 304 stainless steel and high rate loading of ferromagnetic materials is discussed. 15 refs., 33 figs

Development of ultrasonic testing technique to inspect containment liners embedded in concrete on nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Ishida, H.; Kurozumi, Y. [Inst. of Nuclear Safety System, Incorporated, Mihama, Fukui (Japan); Kaneshima, Y. [The Kansai Electric Power Company, Inc., Mihama, Fukui (Japan)

2004-07-01

The purpose of this study is development of ultrasonic testing technique to inspect containment liners embedded in concrete on nuclear power plants. Integrity of containment liners on nuclear power plants can be secured by suitable present operation and maintenance. Furthermore, non-destructive testing technique to inspect embedded liners will ensure the integrity of the containment further. In order to develop the non-destructive testing technique, ultrasonic transducers were made newly and ultrasonic testing data acquisition and evaluation were carried out by using a mock-up. We adopted the surface shear horizontal (SH) wave, low frequency (0.3-0.5MHz), to be able to detect an echo from a defect against attenuation of ultrasonic waves due to long propagation in the liners and dispersion into concrete. We made transducers with three large active elements (40mm x 40mm) in a line which were equivalent to a 120mm width active element. Artificial hollows, {phi}200mm - 19mm depth (1/2thickness) and {phi}200mm - 9.5mm depth (1/4thickness), were made on a surface of a mock-up: carbon steel plate, 38mm thickness, 2,000mm length, 1000mm width. The surfaces of the plate were covered with concrete in order to simulate liners embedded in concrete. As a result of the examinations, the surface SH transducers could detect clearly the echo from the hollows at a distance of 1500mm. We evaluate that the newly made surface SH transducers with three elements have ability of detection of defects such as corrosion on the liners embedded in concrete. (author)

Experimental test of a new technique of background suppression in digital mammography

Energy Technology Data Exchange (ETDEWEB)

Bisogni, M.G.; Bottari, S.; Ciocci, M.A.; Fantacci, M.E.; Maestro, P.; Malakhov, N.; Marrocchesi, P.S. E-mail: marrocchesi@pi.infn.it; Novelli, M.; Quattrocchi, M.; Pilo, F.; Rosso, V.; Turini, N.; Zucca, S

2002-02-01

A multiple-exposure technique in digital mammography has been developed to suppress the physical background in the image due to Compton scattering in the body. A pair of X-ray masks, shaped in a projective geometry and positioned upstream and downstream the patient, are coupled mechanically and moved in four steps along a square pattern in order to irradiate the full area in four consecutive short exposures. A proof-of-principle apparatus is under test with a breast phantom and a standard mammographic X-ray unit. Results are reported.

Experimental test of a new technique of background suppression in digital mammography

International Nuclear Information System (INIS)

Bisogni, M.G.; Bottari, S.; Ciocci, M.A.; Fantacci, M.E.; Maestro, P.; Malakhov, N.; Marrocchesi, P.S.; Novelli, M.; Quattrocchi, M.; Pilo, F.; Rosso, V.; Turini, N.; Zucca, S.

2002-01-01

A multiple-exposure technique in digital mammography has been developed to suppress the physical background in the image due to Compton scattering in the body. A pair of X-ray masks, shaped in a projective geometry and positioned upstream and downstream the patient, are coupled mechanically and moved in four steps along a square pattern in order to irradiate the full area in four consecutive short exposures. A proof-of-principle apparatus is under test with a breast phantom and a standard mammographic X-ray unit. Results are reported

Testing of a new prototype surgical stapler that automates the rollover sleeve technique for venous anastomoses

OpenAIRE

PATRICIA B CARROLL; WERVISTON DEFARIA; CARLOS GANDIA; MARIANA BERHO; EVANGELOS MISIAKOS; ANDREAS G TZAKIS

2006-01-01

The creation of successful vascular anastomoses is of primary importance in many surgical fields. Numerous attempts to automate this process have been made. These techniques have slowly gained acceptance, but their use is still limited. This report details feasibility testing of a new prototype stapler that automates the rollover sleeve technique for venous vascular anastomoses. Male and female mongrel dogs (n=7) (25-32 kg) were used. A segment of the right (n=5) or left (n=2) iliac vein was ...

Model techniques for testing heated concrete structures

International Nuclear Information System (INIS)

Stefanou, G.D.

1983-01-01

Experimental techniques are described which may be used in the laboratory to measure strains of model concrete structures representing to scale actual structures of any shape or geometry, operating at elevated temperatures, for which time-dependent creep and shrinkage strains are dominant. These strains could be used to assess the distribution of stress in the scaled structure and hence to predict the actual behaviour of concrete structures used in nuclear power stations. Similar techniques have been employed in an investigation to measure elastic, thermal, creep and shrinkage strains in heated concrete models representing to scale parts of prestressed concrete pressure vessels for nuclear reactors. (author)

Radioisotope esophageal transit test. A new technique for esophageal emptying and gastroesophageal reflux

Energy Technology Data Exchange (ETDEWEB)

Miyazono, K.; Fukuda, K.; Toyonaga, A. (Kurume Univ., Fukuoka (Japan). School of Medicine)

1982-06-01

A new technique employed sup(99m)Tc-MAA for the study of esophageal dysfunction and its clinical implication were evaluated in the patients with achalasia, progressive systemic sclerosis, reflux esophagitis and 10 normal controls. To investigate esophageal emptying and gastroesophageal reflux, a homogeneous bolus of sup(99m)Tc-MAA in 15ml of water was swallowed in the upright and supine positions under the collimeter of a gamma camera linked to nuclear medicine data analyser (Shimazu Scinti Pack 1200). This radionuclide transit study made a quantitative evaluation of the esophageal dysfunction possible in all cases. Comparing the conventional esophageal function test procedures, this test is a safe, noninvasive and more physiological and sensitive in detecting abnormal esophageal emptying and gastroesophageal reflux.

Investigation of CTBT OSI Radionuclide Techniques at the DILUTED WATERS Nuclear Test Site

Energy Technology Data Exchange (ETDEWEB)

Baciak, James E.; Milbrath, Brian D.; Detwiler, Rebecca S.; Kirkham, Randy R.; Keillor, Martin E.; Lepel, Elwood A.; Seifert, Allen; Emer, Dudley; Floyd, Michael

2012-11-01

Under the Comprehensive Nuclear-Test-Ban Treaty (CTBT), a verification regime that includes the ability to conduct an On-Site Inspection (OSI) will be established. The Treaty allows for an OSI to include many techniques, including the radionuclide techniques of gamma radiation surveying and spectrometry and environmental sampling and analysis. Such radioactivity detection techniques can provide the “smoking gun” evidence that a nuclear test has occurred through the detection and quantification of indicative recent fission products. An OSI faces restrictions in time and manpower, as dictated by the Treaty; not to mention possible logistics difficulties due to the location and climate of the suspected explosion site. It is thus necessary to have a good understanding of the possible source term an OSI will encounter and the proper techniques that will be necessary for an effective OSI regime. One of the challenges during an OSI is to locate radioactive debris that has escaped an underground nuclear explosion (UNE) and settled on the surface near and downwind of ground zero. To support the understanding and selection of sampling and survey techniques for use in an OSI, we are currently designing an experiment, the Particulate Release Experiment (PRex), to simulate a small-scale vent from an underground nuclear explosion. PRex will occur at the Nevada National Security Site (NNSS). The project is conducted under the National Center for Nuclear Security (NCNS) funded by the National Nuclear Security Agency (NNSA). Prior to the release experiment, scheduled for Spring of 2013, the project scheduled a number of activities at the NNSS to prepare for the release experiment as well as to utilize the nuclear testing past of the NNSS for the development of OSI techniques for CTBT. One such activity—the focus of this report—was a survey and sampling campaign at the site of an old UNE that vented: DILUTED WATERS. Activities at DILUTED WATERS included vehicle-based survey

Mechanical system diagnostics using vibration testing techniques

Science.gov (United States)

Mcleod, Catherine D.; Raju, P. K.; Crocker, M. J.

1990-01-01

The 'Cepstrum' technique of vibration-path identification allows the recovery of the transfer function of a system with little knowledge as to its excitation force, by means of a mathematical manipulation of the system output in conjunction with subtraction of part of the output and suitable signal processing. An experimental program has been conducted to evaluate the usefulness of this technique in the cases of simple, cantilever-beam and free-free plate structures as well as in that of a complex mechanical system. On the basis of the transfer functions thus recovered, it was possible to evaluate the shifts in the resonance frequencies of a structure due to the presence of defects.

Specific radiography technique

International Nuclear Information System (INIS)

Abdul Nassir Ibrahim; Azali Muhammad; Ab. Razak Hamzah; Abd. Aziz Mohamed; Mohamad Pauzi Ismail

2008-01-01

Beside radiography testing using x-ray machine and gamma source, there are several technique that developed specifically to complete the testing that cannot be done with the two earlier. This technique was specific based on several factor, for the example, the advantages of neutron and electron using to show the image was unique compare to x-ray and gamma. Besides that, these special radiography techniques maybe differ in how to detect the radiation get through the object. These technique can used to inspect thin or specimen that contained radioactive material. There are several technique will discussed in this chapter such as neutron radiography, electron radiography, fluoroscopy and also autoradiography.

Tests of a new axial sputtering technique in an ECRIS

International Nuclear Information System (INIS)

Scott, R.; Pardo, R.; Vondrasek, R.

2012-01-01

Axial and radial sputtering techniques have been used over the years to create beams from an ECRIS at multiple accelerator facilities. Operational experience has shown greater beam production when using the radial sputtering method versus axial sputtering. At Argonne National Laboratory, previous work with radial sputtering has demonstrated that the position of the sputter sample relative to the plasma chamber wall influences sample drain current, beam production and charge state distribution. The possibility of the chamber wall acting as a ground plane which influences the sputtering of material has been considered, and an attempt has been made to mimic this possible ground plane effect with a coaxial sample introduced from the injection end. Results of these tests will be shown as well as comparisons of outputs using the two methods. The paper is followed by the associated poster. (authors)

Imaging techniques for ultrasonic testing; Bildgebende Verfahren fuer die Ultraschallpruefung

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-07-01

These seminar proceedings contain 16 lectures on the following topics: 1. From imaging to quantification - ultrasound methods in medical diagnostics; 2. SAFT, TOFD, Phased Array - classical applications and recent developments in ultrasonic imaging; 3. Innovative ultrasonic imaging methods in research and application; 4. Industrial ultrasonic testing of fibre-reinforced structures of complex geometry; 5. Visualisation of crack tips in the inspection of wheel set shafts with longitudinal boreholes as a means of avoiding unnecessary wheel set changes; 6. Areal analysis of the propagation of Lamb waves on curved, anisotropic structures; 7. High-resolution representation in immersion technique testing; 8. Variants in generating images from phased array measurement data - practical examples involving copper, carbon-fibre reinforced plastic and other materials; 9. GIUM - an unconventional method of microstructure imaging using ultrasonic stimulation and laser vibrometry scanning; 10. Innovative air-ultrasonic testing concepts for improved imaging; 11. Use of imaging methods for improving the quality of test results from nondestructive testing; 12. Modelling and visualisation of EMUS stimulation for transducer optimisation; 13. Use of SAFT in the manufacture of energy conversion machines; 14. Ultrasonic imaging tests for improved defect characterisation during weld seam inspection on longitudinally welded large-diameter pipes; 15. SAFT reconstruction for testing austenitic weld seams and dissimilar metal weld seams for transverse cracks; 16. Imaging-based optimisation method for quantitative ultrasonic testing of anisotropic inhomogeneous austenitic welded joints with determination and utilisation of their elastic properties. One contribution has been abstracted separately. [German] Dieser Seminarband enthaelt 16 Vortraege mit folgenden Themen: 1. Von der Bildgebung bis zur Quantifizierung - Ultraschallverfahren in der medizinischen Diagnostik; 2. SAFT, TOFD, Phased Array

Influence of Reinforcement Parameters and Ageing Time on Mechanical Behavior of Novel Al2024/SiC/Red Mud Composites Using Response Surface Methodology

Science.gov (United States)

Singh, Jaswinder; Chauhan, Amit

2017-12-01

This study investigates the mechanical behavior of aluminum 2024 matrix composites reinforced with silicon carbide and red mud particles. The hybrid reinforcements were successfully incorporated into the alloy matrix using the stir casting process. An orthogonal array based on Taguchi's technique was used to acquire experimental data for mechanical properties (hardness and impact energy) of the composites. The analysis of variance (ANOVA) and response surface methodology (RSM) techniques were used to evaluate the influence of test parameters (reinforcement ratio, particle size and ageing time). The morphological analysis of the surfaces (fractured during impact tests) was conducted to identify the failure mechanism. Finally, a confirmation experiment was performed to check the adequacy of the developed model. The results indicate that the ageing time is the most effective parameter as far as the hardness of the hybrid composites is concerned. It has also been revealed that red mud wt.% has maximum influence on the impact energy characteristics of the hybrid composites. The study concludes that Al2024/SiC/red mud hybrid composites possess superior mechanical performance in comparison to pure alloy under optimized conditions.

Agricultural soils decontamination techniques: methods and results of tests realized near Chernobyl

International Nuclear Information System (INIS)

Maubert, H.; Jouve, A.; Mary, N.

1992-01-01

After a major nuclear accident, decontamination of agricultural soils would be necessary in order to reclaim the land. Specific techniques were studied in the framework of the European program for Rehabilitation of Soils and Surfaces after an Accident (RESSAC). Different ways to remove the top layer of soils are described, and especially the use of Decontaminating Vegetal Network (D.V.N.) combined with spraying of organic polymers. Real scale tests in the 30 km zone around the Chernobyl nuclear power plant showed that it is possible to achieve an excellent decontamination of agricultural fields (decontamination factor greater than 95%. (author)

Selected hydraulic test analysis techniques for constant-rate discharge tests

International Nuclear Information System (INIS)

Spane, F.A. Jr.

1993-03-01

The constant-rate discharge test is the principal field method used in hydrogeologic investigations for characterizing the hydraulic properties of aquifers. To implement this test, the aquifer is stressed by withdrawing ground water from a well, by using a downhole pump. Discharge during the withdrawal period is regulated and maintained at a constant rate. Water-level response within the well is monitored during the active pumping phase (i.e., drawdown) and during the subsequent recovery phase following termination of pumping. The analysis of drawdown and recovery response within the stress well (and any monitored, nearby observation wells) provides a means for estimating the hydraulic properties of the tested aquifer, as well as discerning formational and nonformational flow conditions (e.g., wellbore storage, wellbore damage, presence of boundaries, etc.). Standard analytical methods that are used for constant-rate pumping tests include both log-log type-curve matching and semi-log straight-line methods. This report presents a current ''state of the art'' review of selected transient analysis procedures for constant-rate discharge tests. Specific topics examined include: analytical methods for constant-rate discharge tests conducted within confined and unconfined aquifers; effects of various nonideal formation factors (e.g., anisotropy, hydrologic boundaries) and well construction conditions (e.g., partial penetration, wellbore storage) on constant-rate test response; and the use of pressure derivatives in diagnostic analysis for the identification of specific formation, well construction, and boundary conditions

Testing and evaluation of existing techniques for identifying uptakes and measuring retention of uranium in mill workers

International Nuclear Information System (INIS)

1983-03-01

Preliminary tests and evaluations of existing bio-analytical techniques for identifying uptakes and measuring retention of uranium in mill workers were made at two uranium mills. Urinalysis tests were found to be more reliable indicators of uranium uptakes than personal air sampling. Static air samples were not found to be good indicators of personal uptakes. In vivo measurements of uranium in lung were successfully carried out in the presence of high and fluctuating background radiation. Interference from external contamination was common during end of shift measurements. A full scale study to evaluate model parameters for the uptake, retention and elimination of uranium should include, in addition to the above techniques, particle size determination of airborne uranium, solubility in simulated lung fluid, uranium analysis in faeces and bone and minute volume measurements for each subject

Human-milk intake measured by administration of deuterium oxide to the mother: a comparison with the test-weighing technique

International Nuclear Information System (INIS)

Butte, N.F.; Wong, W.W.; Patterson, B.W.; Garza, C.; Klein, P.D.

1988-01-01

A comparison was made between the dose-to-the-mother deuterium-dilution method and the conventional test-weighing technique for determining human-milk intake in five exclusively breast-fed infants and in four breast-fed infants who received supplemental foods. After administration of 2 H to the mothers human milk and infant urine were sampled over 14 d and analyzed for 2 H: 1 H ratios by gas-isotope-ratio mass spectrometry. Infant total body water was determined by 18 O dilution. The test-weighing procedure was conducted for 5 d consecutively. The intake of human milk (mean +/- SD) estimated by 2 H dilution was 648 +/- 63 g/d and estimated by test-weighing was 636 +/- 84 g/d. The mean difference between the two methods was not significantly different from 0. The 2 H-dilution and test-weighing techniques provide similar estimates of human-milk intake

Dynamic acousto-elastic testing of concrete with a coda-wave probe: comparison with standard linear and nonlinear ultrasonic techniques.

Science.gov (United States)

Shokouhi, Parisa; Rivière, Jacques; Lake, Colton R; Le Bas, Pierre-Yves; Ulrich, T J

2017-11-01

The use of nonlinear acoustic techniques in solids consists in measuring wave distortion arising from compliant features such as cracks, soft intergrain bonds and dislocations. As such, they provide very powerful nondestructive tools to monitor the onset of damage within materials. In particular, a recent technique called dynamic acousto-elasticity testing (DAET) gives unprecedented details on the nonlinear elastic response of materials (classical and non-classical nonlinear features including hysteresis, transient elastic softening and slow relaxation). Here, we provide a comprehensive set of linear and nonlinear acoustic responses on two prismatic concrete specimens; one intact and one pre-compressed to about 70% of its ultimate strength. The two linear techniques used are Ultrasonic Pulse Velocity (UPV) and Resonance Ultrasound Spectroscopy (RUS), while the nonlinear ones include DAET (fast and slow dynamics) as well as Nonlinear Resonance Ultrasound Spectroscopy (NRUS). In addition, the DAET results correspond to a configuration where the (incoherent) coda portion of the ultrasonic record is used to probe the samples, as opposed to a (coherent) first arrival wave in standard DAET tests. We find that the two visually identical specimens are indistinguishable based on parameters measured by linear techniques (UPV and RUS). On the contrary, the extracted nonlinear parameters from NRUS and DAET are consistent and orders of magnitude greater for the damaged specimen than those for the intact one. This compiled set of linear and nonlinear ultrasonic testing data including the most advanced technique (DAET) provides a benchmark comparison for their use in the field of material characterization. Copyright © 2017 Elsevier B.V. All rights reserved.

Acoustic Modifications of the Ames 40x80 Foot Wind Tunnel and Test Techniques for High-Speed Research Model Testing

Science.gov (United States)

Soderman, Paul T.; Olson, Larry (Technical Monitor)

1995-01-01

The NFAC 40- by 80- Foot Wind Tunnel at Ames is being refurbished with a new, deep acoustic lining in the test section which will make the facility nearly anechoic over a large frequency range. The modification history, key elements, and schedule will be discussed. Design features and expected performance gains will be described. Background noise reductions will be summarized. Improvements in aeroacoustic research techniques have been developed and used recently at NFAC on several wind tunnel tests of High Speed Research models. Research on quiet inflow microphones and struts will be described. The Acoustic Survey Apparatus in the 40x80 will be illustrated. A special intensity probe was tested for source localization. Multi-channel, high speed digital data acquisition is now used for acoustics. And most important, phased microphone arrays have been developed and tested which have proven to be very powerful for source identification and increased signal-to-noise ratio. Use of these tools for the HEAT model will be illustrated. In addition, an acoustically absorbent symmetry plane was built to satisfy the HEAT semispan aerodynamic and acoustic requirements. Acoustic performance of that symmetry plane will be shown.

Experimental design techniques in statistical practice a practical software-based approach

CERN Document Server

Gardiner, W P

1998-01-01

Provides an introduction to the diverse subject area of experimental design, with many practical and applicable exercises to help the reader understand, present and analyse the data. The pragmatic approach offers technical training for use of designs and teaches statistical and non-statistical skills in design and analysis of project studies throughout science and industry. Provides an introduction to the diverse subject area of experimental design and includes practical and applicable exercises to help understand, present and analyse the data Offers technical training for use of designs and teaches statistical and non-statistical skills in design and analysis of project studies throughout science and industry Discusses one-factor designs and blocking designs, factorial experimental designs, Taguchi methods and response surface methods, among other topics.

Utilization of Cell-Transfer Technique for Molecular Testing on Hematoxylin-Eosin-Stained Sections: A Viable Option for Small Biopsies That Lack Tumor Tissues in Paraffin Block.

Science.gov (United States)

Wu, Howard H; Jovonovich, Stephen M; Randolph, Melissa; Post, Kristin M; Sen, Joyashree D; Curless, Kendra; Cheng, Liang

2016-12-01

- In some instances the standard method of doing molecular testing from formalin-fixed, paraffin-embedded block is not possible because of limited tissue. Tumor cell-enriched cell-transfer technique has been proven useful for performing immunocytochemistry and molecular testing on cytologic smears. - To establish the cell-transfer technique as a viable option for isolating tumor cells from hematoxylin-eosin (H&E)-stained slides. - Molecular testing was performed by using the cell-transfer technique on 97 archived H&E-stained slides from a variety of different tumors. Results were compared to the conventional method of molecular testing. - Polymerase chain reaction-based molecular testing via the cell-transfer technique was successfully performed on 82 of 97 samples (85%). This included 39 of 47 cases for EGFR, 10 of 11 cases for BRAF, and 33 of 39 cases for KRAS mutations. Eighty-one of 82 cell-transfer technique samples (99%) showed agreement with previous standard method results, including 4 mutations and 35 wild-type alleles for EGFR, 4 mutations and 6 wild-type alleles for BRAF, and 11 mutations and 21 wild-type alleles for KRAS. There was only 1 discrepancy: a cell-transfer technique with a false-negative >KRAS result (wild type versus G12C). - Molecular testing performed on H&E-stained sections via cell-transfer technique is useful when tissue from cell blocks and small surgical biopsy samples is exhausted and the only available material for testing is on H&E-stained slides.

Numerical and physical testing of upscaling techniques for constitutive properties

International Nuclear Information System (INIS)

McKenna, S.A.; Tidwell, V.C.

1995-01-01

This paper evaluates upscaling techniques for hydraulic conductivity measurements based on accuracy and practicality for implementation in evaluating the performance of the potential repository at Yucca Mountain. Analytical and numerical techniques are compared to one another, to the results of physical upscaling experiments, and to the results obtained on the original domain. The results from different scaling techniques are then compared to the case where unscaled point scale statistics are used to generate realizations directly at the flow model grid-block scale. Initital results indicate that analytical techniques provide upscaling constitutive properties from the point measurement scale to the flow model grid-block scale. However, no single analytic technique proves to be adequate for all situations. Numerical techniques are also accurate, but they are time intensive and their accuracy is dependent on knowledge of the local flow regime at every grid-block

Optical Measurement Techniques for Rocket Engine Testing and Component Applications: Digital Image Correlation and Dynamic Photogrammetry

Science.gov (United States)

Gradl, Paul

2016-01-01

NASA Marshall Space Flight Center (MSFC) has been advancing dynamic optical measurement systems, primarily Digital Image Correlation, for extreme environment rocket engine test applications. The Digital Image Correlation (DIC) technology is used to track local and full field deformations, displacement vectors and local and global strain measurements. This technology has been evaluated at MSFC through lab testing to full scale hotfire engine testing of the J-2X Upper Stage engine at Stennis Space Center. It has been shown to provide reliable measurement data and has replaced many traditional measurement techniques for NASA applications. NASA and AMRDEC have recently signed agreements for NASA to train and transition the technology to applications for missile and helicopter testing. This presentation will provide an overview and progression of the technology, various testing applications at NASA MSFC, overview of Army-NASA test collaborations and application lessons learned about Digital Image Correlation.

Metamodels for Computer-Based Engineering Design: Survey and Recommendations

Science.gov (United States)

Simpson, Timothy W.; Peplinski, Jesse; Koch, Patrick N.; Allen, Janet K.

1997-01-01

The use of statistical techniques to build approximations of expensive computer analysis codes pervades much of todays engineering design. These statistical approximations, or metamodels, are used to replace the actual expensive computer analyses, facilitating multidisciplinary, multiobjective optimization and concept exploration. In this paper we review several of these techniques including design of experiments, response surface methodology, Taguchi methods, neural networks, inductive learning, and kriging. We survey their existing application in engineering design and then address the dangers of applying traditional statistical techniques to approximate deterministic computer analysis codes. We conclude with recommendations for the appropriate use of statistical approximation techniques in given situations and how common pitfalls can be avoided.

Optimization in CNC end milling of UNS C34000 medium leaded ...

Indian Academy of Sciences (India)

response optimization and off-line control of multiple surface quality ... feed rate, depth of cut, step over and total machining time for AISI 1040 steel. .... Taguchi Method was proposed by Genichi Taguchi, a Japanese quality management.

Microfluidic Chip-based Nucleic Acid Testing using Gingival Crevicular Fluid as a New Technique for Detecting HIV-1 Infection

Directory of Open Access Journals (Sweden)

Alex Willyandre

2013-05-01

Full Text Available Transmission of HIV-1 infection by individuals in window period who are tested negative in conventional HIV-1 detection would pose the community with serious problems. Several diagnostic tools require specific labora-tory equipment, perfect timing of diagnosis, antibody to HIV-1, and invasive technique to get sample for examination, until high amount of time to process the sample as well as accessibility of remote areas. Many attempts have been made to solve those problems to come to a new detection technique. This review aims to give information about the current development technique for detection of HIV infection. Microfluidic Chip-based Nucleic Acid Testing is currently introduced for detection of HIV-1 infection. This review also cover the possible usage of gingival crevicular fluid as sample specimen that could be taken noninvasively from the individual.DOI: 10.14693/jdi.v18i2.63

AGARD Flight Test Techniques Series. Volume 9. Aircraft Exterior Noise Measurement and Analysis Techniques. (Le Bruit a l’Exterieur des Aeronefs: Techniques de Mesure et d’Analyse)

Science.gov (United States)

1991-04-01

sugeseed to me to write ui AGARDograpit on A~rlmaft Noie Mms dsurnent Anallysis Techniques’. Being overjoyed, and quite honoured. I realdily agreed to his...Gelt& I )nd Delta 2 terms) Wb) Source Noise Correction - Jet Engine Noise ’) ielts 3 term) (c) Snor"e Noise Correction - Propeller Noise (Delta 3...printed out, since it is impractical to write these down by hand durilg th,. test). One track on each tape-recorder must be used to record a time code

Prediction of high level vibration test results by use of available inelastic analysis techniques

International Nuclear Information System (INIS)

Hofmayer, C.H.; Park, Y.J.; Costello, J.F.

1991-01-01

As part of a cooperative study between the United States and Japan, the US Nuclear Regulatory Commission and the Ministry of International Trade and Industry of Japan agreed to perform a test program that would subject a large scale piping model to significant plastic strains under excitation conditions much greater than the design condition for nuclear power plants. The objective was to compare the results of the tests with state-of-the-art analyses. Comparisons were done at different excitation levels from elastic to elastic-plastic to levels where cracking was induced in the test model. The program was called the high Level Vibration Test (HLVT). The HLVT was performed on the seismic table at the Tadotsu Engineering Laboratory of Nuclear Power Engineering Test Center in Japan. The test model was constructed by modifying the 1/2.5 scale model of one loop of a PWR primary coolant system which was previously tested by NUPEC as part of their seismic proving test program. A comparison of various analysis techniques with test results shows a higher prediction error in the detailed strain values than in the overall response values. This prediction error is magnified as the plasticity in the test model increases. There is no significant difference in the peak responses between the simplified and the detailed analyses. A comparison between various detailed finite element model runs indicates that the material properties and plasticity modeling have a significant impact on the plastic strain responses under dynamic loading reversals. 5 refs., 12 figs

Proficiency Testing for Determination of Water Content in Toluene of Chemical Reagents by iteration robust statistic technique

Science.gov (United States)

Wang, Hao; Wang, Qunwei; He, Ming

2018-05-01

In order to investigate and improve the level of detection technology of water content in liquid chemical reagents of domestic laboratories, proficiency testing provider PT0031 (CNAS) has organized proficiency testing program of water content in toluene, 48 laboratories from 18 provinces/cities/municipals took part in the PT. This paper introduces the implementation process of proficiency testing for determination of water content in toluene, including sample preparation, homogeneity and stability test, the results of statistics of iteration robust statistic technique and analysis, summarized and analyzed those of the different test standards which are widely used in the laboratories, put forward the technological suggestions for the improvement of the test quality of water content. Satisfactory results were obtained by 43 laboratories, amounting to 89.6% of the total participating laboratories.

Comparison of CFD and Test Techniques for Cavitation Inception

International Nuclear Information System (INIS)

Lee, Do Hwan; Park, Sung Keun; Lee, Sun Ki; Kim, Byung Kon

2009-01-01

Cavitation erosion on centrifugal pump impellers is a one of the fundamental factors that cause performance degradation and life shortening of the pumps. One approach to estimate the expected life of an impeller is to use sheet cavity length on the blade surface. While observing the cavity length is more suitable to accurately predict the impeller damage, it is not readily available in the field or on the test stand. Recently, the prediction of the cavity length by using commercial CFD codes has been tried by several authors. As an alternative to direct measure the cavity length of an impeller, a means of estimating cavity length of an impeller based on the relation of operating NPSH to that of 3% NPSH and inception NPSH was developed by Cooper. Although this method seems to be attractive, it is not easy to accurately estimate the inception NPSH without flow visualization. Some recent researchers has been paid attention to apply the high frequency Acoustic Emission(AE) technique to detect cavitation inception of pumps. As an effort to better estimate the cavity length without relying on flow visualization, CFD calculations and experiments were performed and then the results are compared in this study

Quality evaluation of PHWR fuel element end cap weld joints by ultrasonic testing technique

Energy Technology Data Exchange (ETDEWEB)

Singh, J L; Nair, V R; Ramadasan, E; Majumdar, S; Sahoo, K C [Bhabha Atomic Research Centre, Bombay (India). Radiometallurgy Div.; Kumar, Arun [Atomic Fuel Fabrication Facility, Tarapur (India)

1994-12-31

An ultrasonic testing technique has been developed for effective quality evaluation of Pressurised Heavy Water Reactor (PHWR) fuel end plug welds. A focused high frequency shear wave is directed to the weld zone from half skip distance to detect lack of fusion, porosities and wall cracks in the weld zone. A tentative select/reject level has been evolved to sort out the defective weld by examining more than 700 PHWR fuel pin welds. (author). 5 refs., 5 figs.

Studies on the Parametric Effects of Plasma Arc Welding of 2205 Duplex Stainless Steel

Science.gov (United States)

Selva Bharathi, R.; Siva Shanmugam, N.; Murali Kannan, R.; Arungalai Vendan, S.

2018-03-01

This research study attempts to create an optimized parametric window by employing Taguchi algorithm for Plasma Arc Welding (PAW) of 2 mm thick 2205 duplex stainless steel. The parameters considered for experimentation and optimization are the welding current, welding speed and pilot arc length respectively. The experimentation involves the parameters variation and subsequently recording the depth of penetration and bead width. Welding current of 60-70 A, welding speed of 250-300 mm/min and pilot arc length of 1-2 mm are the range between which the parameters are varied. Design of experiments is used for the experimental trials. Back propagation neural network, Genetic algorithm and Taguchi techniques are used for predicting the bead width, depth of penetration and validated with experimentally achieved results which were in good agreement. Additionally, micro-structural characterizations are carried out to examine the weld quality. The extrapolation of these optimized parametric values yield enhanced weld strength with cost and time reduction.

RELIABILITY OF CERTAIN TESTS FOR EVALUATION OF JUDO TECHNIQUES

Directory of Open Access Journals (Sweden)

Slavko Obadov

2007-05-01

Full Text Available The sample included 106 judokas. Assessment of the level of mastership of judo techniques was carried out by evaluation of fi ve competent studies. Each subject performed a technique three times and each performance was evaluated by the judges. In order to evaluate measurement of each technique, Cronbach’s coeffi cient of reliability  was calculated. During the procedure the subjects's results were also transformed to factor scores i.e. the results of each performer at the main component of evaluation in the fi ve studies. These factor scores could be used in the subsequent procedure of multivariant statistical analysis.

Techniques involving extreme environment, nondestructive techniques, computer methods in metals research, and data analysis

International Nuclear Information System (INIS)

Bunshah, R.F.

1976-01-01

A number of different techniques which range over several different aspects of materials research are covered in this volume. They are concerned with property evaluation of 4 0 K and below, surface characterization, coating techniques, techniques for the fabrication of composite materials, computer methods, data evaluation and analysis, statistical design of experiments and non-destructive test techniques. Topics covered in this part include internal friction measurements; nondestructive testing techniques; statistical design of experiments and regression analysis in metallurgical research; and measurement of surfaces of engineering materials

4. International colloquium on nondestructive testing techniques

International Nuclear Information System (INIS)

Anon.

The different papers about non destructive testing (ultrasonic testing, eddy current testing, radiography etc...) are presented. The colloquium deals particularly with utilization in the nuclear field for quality of materials, quality control, improvement of performances or automation [fr

Optimization of machining parameters of hard porcelain on a CNC ...

African Journals Online (AJOL)

Optimization of machining parameters of hard porcelain on a CNC machine by Taguchi-and RSM method. ... Journal Home > Vol 10, No 1 (2018) > ... The conduct of experiments was made by employing the Taguchi's L27 Orthogonal array to ...

Biomechanical testing of new meniscal repair techniques containing ultra high-molecular weight polyethylene suture.

Science.gov (United States)

Barber, F Alan; Herbert, Morley A; Schroeder, F Alexander; Aziz-Jacobo, Jorge; Sutker, Michael J

2009-09-01

To evaluate the biomechanical characteristics of current meniscal repair techniques containing ultra high-molecular weight polyethylene (UHMWPE) suture with and without cyclic loading. Vertical longitudinal cuts made in porcine menisci were secured with a single repair device. Noncycled and cycled (500 cycles) biomechanical tests were performed on the following groups: group 1, No. 2-0 Mersilene vertical suture (Ethicon, Somerville, NJ); group 2, No. 2-0 Orthocord vertical suture (DePuy Mitek, Westwood, MA); group 3, No. 0 Ultrabraid vertical suture (Smith & Nephew Endoscopy, Andover, MA); group 4, No. 2-0 FiberWire vertical suture (Arthrex, Naples, FL); group 5, vertically oriented mattress suture by use of an Ultra FasT-Fix device (Smith & Nephew Endoscopy) with No. 0 Ultrabraid; group 6, vertically oriented mattress suture by use of a RapidLoc A2 device (DePuy Mitek) with No. 2-0 Orthocord suture; group 7, vertically oriented stitch by use of a MaxFire device with MaxBraid PE suture (Biomet Sports Medicine, Warsaw, IN); and group 8, an obliquely oriented stitch of No. 0 UHMWPE suture inserted by use of a CrossFix device (Cayenne Medical, Scottsdale, AZ). Endpoints were failure loads, failure modes, stiffness, and cyclic displacement. Mean single-pull loads were calculated for Ultra FasT-Fix (121 N), FiberWire (110 N), MaxFire (130 N), Mersilene (84 N), Orthocord (124 N), RapidLoc A2 (86 N), CrossFix (77 N), and Ultrabraid (109 N). After 500 cyclic loads, the Orthocord (222 N) repair was stronger than the others: Ultra FasT-Fix (110 N), FiberWire (117 N), MaxFire (132 N), Mersilene (89 N), RapidLoc A2 (108 N), CrossFix (95 N), and Ultrabraid (126 N) (P Fix, RapidLoc A2, and MaxFire) were comparable to the isolated UHMWPE-containing suture repairs on single-failure load testing. UHMWPE-containing suture repairs are stronger than braided polyester suture repairs, but pure UHMWPE suture (Ultrabraid) elongated more during cycling. Orthocord suture is significantly

Study of Effects on Mechanical Properties of PLA Filament which is blended with Recycled PLA Materials

Science.gov (United States)

Babagowda; Kadadevara Math, R. S.; Goutham, R.; Srinivas Prasad, K. R.

2018-02-01

Fused deposition modeling is a rapidly growing additive manufacturing technology due to its ability to build functional parts having complex geometry. The mechanical properties of the build part is depends on several process parameters and build material of the printed specimen. The aim of this study is to characterize and optimize the parameters such as layer thickness and PLA build material which is mixed with recycled PLA material. Tensile and flexural or bending test are carried out to determine the mechanical response characteristics of the printed specimen. Taguchi method is used for number of experiments and Taguchi S/N ratio is used to identify the set of parameters which give good results for respective response characteristics, effectiveness of each parameters is investigated by using analysis of variance (ANOVA).

Development of small scale mechanical testing techniques on ion beam irradiated 304 SS

International Nuclear Information System (INIS)

Reichardt, A.; Abad, M.D.; Hosemann, P.; Lupinacci, A.; Kacher, J.; Minor, A.; Jiao, Z; Chou, P.

2015-01-01

Austenitic stainless steels are widely used for structural components in light water reactors, however uncertainty in their susceptibility to irradiation assisted stress corrosion cracking (IASCC) has made long term performance predictions difficult. In addition, the testing of reactor irradiated materials has proven challenging due to the long irradiation times required, limited sample availability, and unwanted activation. To address these problems, we apply recently developed techniques in nano-indentation and micro-compression testing to small volume samples of 10 dpa proton-beam irradiated 304 stainless steel. Cross sectional nano-indentation was performed on both proton beam irradiated and non-irradiated samples at temperatures ranging from 22 to 300 C. degrees to determine the effects of irradiation and operating temperature on hardening. Micro-compression tests using 2 μm x 2 μm x 5 μm focused-ion beam milled pillars were then performed in situ in an electron microscope to allow for a more accurate look at stress-strain behavior along with real-time observations of localized mechanical deformation. Large sudden slip events and significant increase in yield strength are observed in irradiated micro-compression samples at room temperature. Elevated temperature nano-indentation results reveal the possibility of thermally-activated changes in deformation mechanism for irradiated specimens. Since the deformation mechanism information provided by micro-compression testing can provide valuable information about IASCC susceptibility, future work will involve ex situ micro-compression tests at reactor operating temperature

Optimizing Injection Molding Parameters of Different Halloysites Type-Reinforced Thermoplastic Polyurethane Nanocomposites via Taguchi Complemented with ANOVA

Directory of Open Access Journals (Sweden)

Tayser Sumer Gaaz

2016-11-01

Taguchi and ANOVA approaches. Seemingly, mHNTs has shown its very important role in the resulting product.

Module Testing Techniques for Nuclear Safety Critical Software Using LDRA Testing Tool

International Nuclear Information System (INIS)

Moon, Kwon-Ki; Kim, Do-Yeon; Chang, Hoon-Seon; Chang, Young-Woo; Yun, Jae-Hee; Park, Jee-Duck; Kim, Jae-Hack

2006-01-01

The safety critical software in the I and C systems of nuclear power plants requires high functional integrity and reliability. To achieve those requirement goals, the safety critical software should be verified and tested according to related codes and standards through verification and validation (V and V) activities. The safety critical software testing is performed at various stages during the development of the software, and is generally classified as three major activities: module testing, system integration testing, and system validation testing. Module testing involves the evaluation of module level functions of hardware and software. System integration testing investigates the characteristics of a collection of modules and aims at establishing their correct interactions. System validation testing demonstrates that the complete system satisfies its functional requirements. In order to generate reliable software and reduce high maintenance cost, it is important that software testing is carried out at module level. Module testing for the nuclear safety critical software has rarely been performed by formal and proven testing tools because of its various constraints. LDRA testing tool is a widely used and proven tool set that provides powerful source code testing and analysis facilities for the V and V of general purpose software and safety critical software. Use of the tool set is indispensable where software is required to be reliable and as error-free as possible, and its use brings in substantial time and cost savings, and efficiency

Testing the potential of geochemical techniques in identifying hydrological systems within landslides in partly weathered marls

Science.gov (United States)

Bogaard, T. A.

2003-04-01

This paper’s objectives are twofold: to test the potential of cation exchange capacity (CEC) analysis for refinement of the knowledge of the hydrological system in landslide areas; and to examine two laboratory CEC analysis techniques on their applicability to partly weathered marls. The NH4Ac and NaCl laboratory techniques are tested. The geochemical results are compared with the core descriptions and interpreted with respect to their usefulness. Both analysis techniques give identical results for CEC, and are plausible on the basis of the available clay content information. The determination of the exchangeable cations was more difficult, since part of the marls dissolved. With the ammonium-acetate method more of the marls are dissolved than with the sodium-chloride method. This negatively affects the results of the exchangeable cations. Therefore, the NaCl method is to be preferred for the determination of the cation fractions at the complex, be it that this method has the disadvantage that the sodium fraction cannot be determined. To overcome this problem it is recommended to try and use another salt e.g. SrCl2 as displacement fluid. Both Alvera and Boulc-Mondorès examples show transitions in cation composition with depth. It was shown that the exchangeable cation fractions can be useful in locating boundaries between water types, especially the boundary between the superficial, rain fed hydrological system and the lower, regional ground water system. This information may be important for landslide interventions since the hydrological system and the origin of the water need to be known in detail. It is also plausible that long-term predictions of slope stability may be improved by knowledge of the hydrogeochemical evolution of clayey landslides. In the Boulc-Mondorès example the subsurface information that can be extracted from CEC analyses was presented. In the Boulc-Mondorès cores deviant intervals of CEC could be identified. These are interpreted as

Advanced in-flight measurement techniques

CERN Document Server

Lawson, Nicholas; Jentink, Henk; Kompenhans, Jürgen

2013-01-01

The book presents a synopsis of the main results achieved during the 3 year EU-project "Advanced Inflight Measurement Techniques (AIM)" which applied advanced image based measurement techniques to industrial flight testing. The book is intended to be not only an overview on the AIM activities but also a guide on the application of advanced optical measurement techniques for future flight testing. Furthermore it is a useful guide for engineers in the field of experimental methods and flight testing who face the challenge of a future requirement for the development of highly accurate non-intrusive in-flight measurement techniques.

Defense Manufacturing Management Guide for Program Managers, Third Edition

Science.gov (United States)

1989-04-01

Crosby (Quality goals of quality, cost, schedule, mission need, College), Genechi Taguchi (Experimental 5-1 Design), Dr. Kaoru Ishikawa (Cause/Effect...the remaining problems were resolved. 5-7 6. Ishikawa Diagram 7. Control Charts This technique was developed by Dr. In the minds of some quality Kaoru ... Ishikawa , one of the foremost professionals and nonprofesslonals alike, the authorities on quality control in Japan. The control chart is synonymous

Reinforcement with alumina particles at the interface region of AA6101-T6 and AA1350 alloys during friction stir welding

Science.gov (United States)

Ashok Kumar, R.; Thansekhar, M. R.

2018-04-01

This paper deals the combinational effect of friction stir welding and friction stir processing on dissimilar AA6101-T6 and AA1350 aluminium alloys. For that, alumina particles are reinforced at interface region of AA6101-T6 and AA1350 aluminium alloys. Friction Stir Welding and Friction Stir Processing are done simultaneously for various sizes of groove. To analyze the welding quality and surface modifications, mechanical, wear and microstructural tests are carried out. Among these, smallest groove of 0.5 mm width and 1 mm depth reveals highest tensile and bending strengths and largest groove of 2 mm width and 3 mm depth gives maximum hardness and wear resistance. Taguchi technique shows that groove width is most influencing parameter. Developed second order models with interaction predict the responses with minimum error.

Wear Response of Aluminium 6061 Composite Reinforced with Red Mud at Elevated Temperature

Directory of Open Access Journals (Sweden)

R. Dabral

2017-09-01

Full Text Available The present work is focused on the investigations on dry sliding wear behaviour of aluminium metal matrix composite at room and elevated temperature. Aluminium metal matrix composites reinforced with red mud are prepared by stir casting method. The experiments are planned using Taguchi technique. An orthogonal array, analysis of variance and signal to noise ratio are used to check the influence of wear parameters like temperature, percentage of reinforcement, mesh size, load, sliding distance and sliding speed on dry sliding wear of composites. The optimal testing parameters are found and their values are calculated which are then compared with predicted values. A reasonable agreement is found between predicted and actual values. The model prepared in the present work can be effectively used to predict the specific wear rate of the composites.

Local confidence limits for IMRT and VMAT techniques: a study based on TG119 test suite

International Nuclear Information System (INIS)

Thomas, M.; Chandroth, M.

2014-01-01

The aim of this study was to generate a local confidence limit (CL) for intensity modulated radiation therapy (IMRT) and volumetric modulated arc therapy (VMAT) techniques used at Waikato Regional Cancer Centre. This work was carried out based on the American Association of Physicists in Medicine (AAPM) Task Group (TG) 119 report. The AAPM TG 119 report recommends CLs as a bench mark for IMRT commissioning and delivery based on its multiple institutions planning and dosimetry comparisons. In this study the locally obtained CLs were compared to TG119 benchmarks. Furthermore, the same bench mark was used to test the capabilities and quality of the VMAT technique in our clinic. The TG 119 test suite consists of two primary and four clinical tests for evaluating the accuracy of IMRT planning and dose delivery systems. Pre defined structure sets contoured on computed tomography images were downloaded from AAPM website and were transferred to a locally designed phantom. For each test case two plans were generated using IMRT and VMAT optimisation. Dose prescriptions and planning objectives recommended by TG119 report were followed to generate the test plans in Eclipse Treatment Planning System. For each plan the point dose measurements were done using an ion chamber at high dose and low dose regions. The planar dose distribution was analysed for percentage of points passing the gamma criteria of 3 %/3 mm, for both the composite plan and individual fields of each plan. The CLs were generated based on the results from the gamma analysis and point dose measurements. For IMRT plans, the CLs obtained were (1) from point dose measurements: 2.49 % at high dose region and 2.95 % for the low dose region (2) from gamma analysis: 2.12 % for individual fields and 5.9 % for the composite plan. For VMAT plans, the CLs obtained were (1) from point dose measurements: 2.56 % at high dose region and 2.6 % for the low dose region (2) from gamma analysis: 1.46 % for individual fields and 0

Training guidelines in non-destructive testing techniques. 2002 edition

International Nuclear Information System (INIS)

2002-01-01

Non-destructive testing (NDT) is a dynamic technology and progresses with time. Since the issuance of IAEA-TECDOC-628 in 1991, the technology has experienced numerous changes. Advancements in knowledge about the behaviour of materials have led to changes in the applicable NDT codes, standards and specifications. In addition, over the last ten years, as a result of extensive research and development activities worldwide, new NDT techniques and equipment have been developed which are accepted by engineering community. To accommodate the latest developments, modifications are required to training materials. The present publication is an updated version of IAEA-TECDOC-628. The modifications were made during an Advisory Group Meeting, held in Vienna from 25-29 June 2001. The content of the first edition of IAEA-TECDOC-628 has been revised based on the experience of the experts, as well as comments of the end-user industries. The time allotment for different topics has been changed without changing the total duration. The details of the topics on each subject have been expanded to include the latest developments in the individual fields. The incorporated changes will help end-the user industries to update their NDT qualification and certification schemes, and course material

Optimization of temperature and time for drying and carbonization to increase calorific value of coconut shell using Taguchi method

Science.gov (United States)

Musabbikhah, Saptoadi, H.; Subarmono, Wibisono, M. A.

2016-03-01

Fossil fuel still dominates the needs of energy in Indonesia for the past few years. The increasing scarcity of oil and gas from non-renewable materials results in an energy crisis. This condition turns to be a serious problem for society which demands immediate solution. One effort which can be taken to overcome this problem is the utilization and processing of biomass as renewable energy by means of carbonization. Thus, it can be used as qualified raw material for production of briquette. In this research, coconut shell is used as carbonized waste. The research aims at improving the quality of coconut shell as the material for making briquettes as cheap and eco-friendly renewable energy. At the end, it is expected to decrease dependence on oil and gas. The research variables are drying temperature and time, carbonization time and temperature. The dependent variable is calorific value of the coconut shell. The method used in this research is Taguchi Method. The result of the research shows thus variables, have a significant contribution on the increase of coconut shell's calorific value. It is proven that the higher thus variables are higher calorific value. Before carbonization, the average calorific value of coconut shell reaches 4,667 call/g, and a significant increase is notable after the carbonization. The optimization is parameter setting of A2B3C3D3, which means that the drying temperature is 105 °C, the drying time is 24 hours, the carbonization temperature is 650 °C and carbonization time is 120 minutes. The average calorific value is approximately 7,744 cal/g. Therefore, the increase of the coconut shell's calorific value after the carbonization is 3,077 cal/g or approximately 60 %. The charcoal of carbonized coconut shell has met the requirement of SNI, thus it can be used as raw material in making briquette which can eventually be used as cheap and environmental friendly fuel.

Formulation and optimization of solid lipid nanoparticle formulation for pulmonary delivery of budesonide using Taguchi and Box-Behnken design.

Science.gov (United States)

Emami, J; Mohiti, H; Hamishehkar, H; Varshosaz, J

2015-01-01

Budesonide is a potent non-halogenated corticosteroid with high anti-inflammatory effects. The lungs are an attractive route for non-invasive drug delivery with advantages for both systemic and local applications. The aim of the present study was to develop, characterize and optimize a solid lipid nanoparticle system to deliver budesonide to the lungs. Budesonide-loaded solid lipid nanoparticles were prepared by the emulsification-solvent diffusion method. The impact of various processing variables including surfactant type and concentration, lipid content organic and aqueous volume, and sonication time were assessed on the particle size, zeta potential, entrapment efficiency, loading percent and mean dissolution time. Taguchi design with 12 formulations along with Box-Behnken design with 17 formulations was developed. The impact of each factor upon the eventual responses was evaluated, and the optimized formulation was finally selected. The size and morphology of the prepared nanoparticles were studied using scanning electron microscope. Based on the optimization made by Design Expert 7(®) software, a formulation made of glycerol monostearate, 1.2 % polyvinyl alcohol (PVA), weight ratio of lipid/drug of 10 and sonication time of 90 s was selected. Particle size, zeta potential, entrapment efficiency, loading percent, and mean dissolution time of adopted formulation were predicted and confirmed to be 218.2 ± 6.6 nm, -26.7 ± 1.9 mV, 92.5 ± 0.52 %, 5.8 ± 0.3 %, and 10.4 ± 0.29 h, respectively. Since the preparation and evaluation of the selected formulation within the laboratory yielded acceptable results with low error percent, the modeling and optimization was justified. The optimized formulation co-spray dried with lactose (hybrid microparticles) displayed desirable fine particle fraction, mass median aerodynamic diameter (MMAD), and geometric standard deviation of 49.5%, 2.06 μm, and 2.98 μm; respectively. Our results provide fundamental data for the

Reliability and normative values of the foot line test: a technique to assess foot posture

DEFF Research Database (Denmark)

Brushøj, C; Larsen, Klaus; Nielsen, MB

2007-01-01

STUDY DESIGN: Test-retest reliability. OBJECTIVE: To examine the reliability and report normative values of a novel test, the foot line test (FLT), to describe foot morphology. BACKGROUND: Numerous foot examinations are performed each day, but most existing examination techniques have considerable...... limitations regarding reliability and validity. METHODS: One hundred thirty subjects with mean foot size 44 (41-50 European size) participated. Two examiners, blinded to each other's measurements, measured the right foot of the subjects twice and the left foot once. The position of the most medial aspect...... of the navicular in the mediolateral direction was projected vertically onto a piece of paper placed under the subject's foot, and compared to the position of the forefoot and hindfoot to obtain the FLT value. RESULTS: FLT values ranged from -8 to 14 mm, with a mean (+/-SD) of 3.7 +/- 3.4 mm. The intratester...

On the testing equipment and experimental techniques for the investigation of the photoviscoelastic behaviour of soft polymers

International Nuclear Information System (INIS)

Weber, H.

1983-01-01

Creep tests with uniaxial stress and pure shear have been carried out in order to determine the behaviour of soft plastics, which is governed by a non-linear material law, and to apply it to the photoelastic analysis of biaxial stress in plastic components under quasistatic and isothermal loads. The test facility is described as well as the technique applied to correct stress/creep curves for sigma=const. Results are presented for plane and tubular samples of soft PVC and an unsaturated polyester. (orig.) [de

Optimization of CNC end milling process parameters using PCA ...

African Journals Online (AJOL)

Optimization of CNC end milling process parameters using PCA-based Taguchi method. ... International Journal of Engineering, Science and Technology ... To meet the basic assumption of Taguchi method; in the present work, individual response correlations have been eliminated first by means of Principal Component ...

Towards Intelligent Interpretation of Low Strain Pile Integrity Testing Results Using Machine Learning Techniques.

Science.gov (United States)

Cui, De-Mi; Yan, Weizhong; Wang, Xiao-Quan; Lu, Lie-Min

2017-10-25

Low strain pile integrity testing (LSPIT), due to its simplicity and low cost, is one of the most popular NDE methods used in pile foundation construction. While performing LSPIT in the field is generally quite simple and quick, determining the integrity of the test piles by analyzing and interpreting the test signals (reflectograms) is still a manual process performed by experienced experts only. For foundation construction sites where the number of piles to be tested is large, it may take days before the expert can complete interpreting all of the piles and delivering the integrity assessment report. Techniques that can automate test signal interpretation, thus shortening the LSPIT's turnaround time, are of great business value and are in great need. Motivated by this need, in this paper, we develop a computer-aided reflectogram interpretation (CARI) methodology that can interpret a large number of LSPIT signals quickly and consistently. The methodology, built on advanced signal processing and machine learning technologies, can be used to assist the experts in performing both qualitative and quantitative interpretation of LSPIT signals. Specifically, the methodology can ease experts' interpretation burden by screening all test piles quickly and identifying a small number of suspected piles for experts to perform manual, in-depth interpretation. We demonstrate the methodology's effectiveness using the LSPIT signals collected from a number of real-world pile construction sites. The proposed methodology can potentially enhance LSPIT and make it even more efficient and effective in quality control of deep foundation construction.

Effective porosity and pore-throat sizes of Conasauga Group mudrock: Application, test and evaluation of petrophysical techniques

International Nuclear Information System (INIS)

Dorsch, J.; Katsube, T.J.; Sanford, W.E.; Univ. of Tennessee, Knoxville, TN; Dugan, B.E.; Tourkow, L.M.

1996-04-01

Effective porosity (specifically referring to the interconnected pore space) was recently recognized as being essential in determining the effectiveness and extent of matrix diffusion as a transport mechanism within fractured low-permeability rock formations. The research presented in this report was performed to test the applicability of several petrophysical techniques for the determination of effective porosity of fine-grained siliciclastic rocks. In addition, the aim was to gather quantitative data on the effective porosity of Conasauga Group mudrock from the Oak Ridge Reservation (ORR). The quantitative data reported here include not only effective porosities based on diverse measurement techniques, but also data on the sizes of pore throats and their distribution, and specimen bulk and grain densities. The petrophysical techniques employed include the immersion-saturation method, mercury and helium porosimetry, and the radial diffusion-cell method

Studies on laws of stress-magnetization based on magnetic memory testing technique

Science.gov (United States)

Ren, Shangkun; Ren, Xianzhi

2018-03-01

Metal magnetic memory (MMM) testing technique is a novel testing method which can early test stress concentration status of ferromagnetic components. Under the different maximum tensile stress, the relationship between the leakage magnetic field of at certain point of cold rolled steel specimen and the tensile stress was measured during the process of loading and unloading by repeated. It shows that when the maximum tensile stress is less than 610 MPa, the relationship between the magnetic induction intensity and the stress is linear; When the maximum tensile stress increase from 610 MPa to 653 MPa of yield point, the relationship between the magnetic induction intensity and the tensile becomes bending line. The location of the extreme point of the bending line will move rapidly from the position of smaller stress to the larger stress position, and the variation of magnetic induction intensity increases rapidly. When the maximum tensile stress is greater than the 653 MPa of yield point, the variation of the magnetic induction intensity remains large, and the position of the extreme point moves very little. In theoretical aspects, tensile stress is to be divided into ordered stress and disordered stress. In the stage of elastic stress, a microscopic model of the order stress magnetization is established, and the conclusions are in good agreement with the experimental data. In the plastic deformation stage, a microscopic model of disordered stress magnetization is established, and the conclusions are in good agreement with the experimental data, too. The research results can provide reference for the accurate quantitative detection and evaluation of metal magnetic memory testing technology.

Fabrication of an Optical Fiber Micro-Sphere with a Diameter of Several Tens of Micrometers.

Science.gov (United States)

Yu, Huijuan; Huang, Qiangxian; Zhao, Jian

2014-06-25

A new method to fabricate an integrated optical fiber micro-sphere with a diameter within 100 µm, based on the optical fiber tapering technique and the Taguchi method is proposed. Using a 125 µm diameter single-mode (SM) optical fiber, an optical fiber taper with a cone angle is formed with the tapering technique, and the fabrication optimization of a micro-sphere with a diameter of less than 100 µm is achieved using the Taguchi method. The optimum combination of process factors levels is obtained, and the signal-to-noise ratio (SNR) of three quality evaluation parameters and the significance of each process factors influencing them are selected as the two standards. Using the minimum zone method (MZM) to evaluate the quality of the fabricated optical fiber micro-sphere, a three-dimensional (3D) numerical fitting image of its surface profile and the true sphericity are subsequently realized. From the results, an optical fiber micro-sphere with a two-dimensional (2D) diameter less than 80 µm, 2D roundness error less than 0.70 µm, 2D offset distance between the micro-sphere center and the fiber stylus central line less than 0.65 µm, and true sphericity of about 0.5 µm, is fabricated.

Fabrication of an Optical Fiber Micro-Sphere with a Diameter of Several Tens of Micrometers

Directory of Open Access Journals (Sweden)

Huijuan Yu

2014-06-01

Full Text Available A new method to fabricate an integrated optical fiber micro-sphere with a diameter within 100 µm, based on the optical fiber tapering technique and the Taguchi method is proposed. Using a 125 µm diameter single-mode (SM optical fiber, an optical fiber taper with a cone angle is formed with the tapering technique, and the fabrication optimization of a micro-sphere with a diameter of less than 100 µm is achieved using the Taguchi method. The optimum combination of process factors levels is obtained, and the signal-to-noise ratio (SNR of three quality evaluation parameters and the significance of each process factors influencing them are selected as the two standards. Using the minimum zone method (MZM to evaluate the quality of the fabricated optical fiber micro-sphere, a three-dimensional (3D numerical fitting image of its surface profile and the true sphericity are subsequently realized. From the results, an optical fiber micro-sphere with a two-dimensional (2D diameter less than 80 µm, 2D roundness error less than 0.70 µm, 2D offset distance between the micro-sphere center and the fiber stylus central line less than 0.65 µm, and true sphericity of about 0.5 µm, is fabricated.

Improvement of ISI techniques by multi-frequency eddy current testing method for steam generator tube in PWR plant

International Nuclear Information System (INIS)

Endo, Takashi; Kamimura, Takeo; Nishihara, Masatoshi; Araki, Yasuo; Fukui, Shigetaka.