Statistics applied to the testing of cladding tubes

International Nuclear Information System (INIS)

Perdijon, J.

1987-01-01

Cladding tubes, either steel or zircaloy, are generally given a 100 % inspection through ultrasonic non-destructive testing. This inspection may be completed beneficially with an eddy current test, as this is not sensitive to the same defects as those typically traced by ultrasonic testing. Unfortunately, the two methods (as with other non-destructive tests) exhibit poor precision; this means that a flaw, whose size is close to that denoted as rejection limit, may be accepted or rejected. Currently, rejection, i.e. the measurement above which a tube is rejected, is generally determined through measuring a calibration tube at regular time intervals, and the signal of a given tube is compared to that of the most recently completed calibration. This measurement is thus subject to variations which can be attributed to an actual shift of adjustments as well as to poor precision. For this reason, monitoring instrument adjustments using the so-called control chart method are proposed

Investigation into the suitability of capillary tubes for microcrystalline testing.

Science.gov (United States)

Elie, Leonie E; Baron, Mark G; Croxton, Ruth S; Elie, Mathieu P

2013-07-01

A comparison between microcrystalline tests performed on microscope slides and flat capillary tubes with inner diameters ranging from 0.1 to 0.7 mm was carried out to explore the appropriateness of tubes for rapid testing of suspected drugs of abuse in the laboratory as well as in the field. Tests for mephedrone, cocaine, and phencyclidine were chosen as examples to investigate the handling of the capillary tubes, the influence on crystal habit, size, and the effects on the limit of detection. Image stacking software was used to increase the depth of field of micrographs taken from developed microcrystals greatly enhancing the interpretability even months after carrying out the microcrystalline test. Additionally, the potential of seeding capillary tubes with a reagent was studied. Pre-treatment of tubes would allow microcrystalline tests to be carried out quicker and anywhere without the necessity of taking along expensive and hazardous reagents. The sealing of capillary tubes containing developed microcrystalline tests in order to preserve results for a long period of time was successfully done by applying paraffin wax to the open ends. Finally, it was concluded that capillary tubes are suitable vessels for performing microcrystalline tests. The increased portability of the improved set-up allows tests to be safely executed outside laboratories without impairing the quality of the result. Findings were applied to six legal high samples purchased online between May and August 2011. The active ingredients like MDAI as well as cutting agents like caffeine were successfully identified using the microcrystalline test technique in capillary tubes. Copyright © 2012 John Wiley & Sons, Ltd.

Sequence Design for a Test Tube of Interacting Nucleic Acid Strands.

Science.gov (United States)

Wolfe, Brian R; Pierce, Niles A

2015-10-16

We describe an algorithm for designing the equilibrium base-pairing properties of a test tube of interacting nucleic acid strands. A target test tube is specified as a set of desired "on-target" complexes, each with a target secondary structure and target concentration, and a set of undesired "off-target" complexes, each with vanishing target concentration. Sequence design is performed by optimizing the test tube ensemble defect, corresponding to the concentration of incorrectly paired nucleotides at equilibrium evaluated over the ensemble of the test tube. To reduce the computational cost of accepting or rejecting mutations to a random initial sequence, the structural ensemble of each on-target complex is hierarchically decomposed into a tree of conditional subensembles, yielding a forest of decomposition trees. Candidate sequences are evaluated efficiently at the leaf level of the decomposition forest by estimating the test tube ensemble defect from conditional physical properties calculated over the leaf subensembles. As optimized subsequences are merged toward the root level of the forest, any emergent defects are eliminated via ensemble redecomposition and sequence reoptimization. After successfully merging subsequences to the root level, the exact test tube ensemble defect is calculated for the first time, explicitly checking for the effect of the previously neglected off-target complexes. Any off-target complexes that form at appreciable concentration are hierarchically decomposed, added to the decomposition forest, and actively destabilized during subsequent forest reoptimization. For target test tubes representative of design challenges in the molecular programming and synthetic biology communities, our test tube design algorithm typically succeeds in achieving a normalized test tube ensemble defect ≤1% at a design cost within an order of magnitude of the cost of test tube analysis.

Counting DNA: estimating the complexity of a test tube of DNA.

Science.gov (United States)

Faulhammer, D; Lipton, R J; Landweber, L F

1999-10-01

We consider the problem of estimation of the 'complexity' of a test tube of DNA. The complexity of a test tube is the number of different kinds of strands of DNA in the test tube. It is quite easy to estimate the number of total strands in a test tube, especially if the strands are all the same length. Estimation of the complexity is much less clear. We propose a simple kind of DNA computation that can estimate the complexity.

Instruments for non-destructive evaluation of advanced test reactor inpile tubes

International Nuclear Information System (INIS)

Livingston, R.A.; Beller, L.S.; Edgett, S.M.

1986-01-01

The Advanced Test Reactor is a 250 MW LWR used primarily for irradiation testing of materials contained in inpile tubes that pass through the reactor core. These tubes provided the high pressure and temperature water environment required for the test specimens. The reactor cooling water surrounding the inpile tubes is at much lower pressure and temperature. The structural integrity of the inpile tubes is monitored by routine surveillance to ensure against unplanned reactor shutdowns to replace defective inpile tubes. The improved instruments developed for inpile tube surveillance include a bore profilometer, ultrasonic flaw detetion system and bore diameter gauges. The design and function of these improved instruments is presented

Development and test evaluation of duplex steam reformer tube

International Nuclear Information System (INIS)

Allen, D.C.; Meyer, D.J.; Pflasterer, G.R.

1980-01-01

For HTR applications involving a steam reformer (SR), it is uncertain whether an intermediate heat exchanger (IHX) is required. There are several system configurations that could be developed for the application of nuclear heat using the steam reformer reaction. The considerations (advantages vs. disadvantages) for each of the system configurations are summarized. The approach that technically and economically appears to be the most attractive, in studies conducted by General Electric, combines the SR process heat exchanger and the IHX in a single component using a duplex tube. A central question concerning the duplex tube concept is whether the design would provide adequate leak monitoring capability and significant reduction in tritium and hydrogen diffusion, while introducing only a small increase in overall temperature difference from the helium to the process gas. A cooperative GE-KFA effort was undertaken to develop, fabricate, test, and evaluate a duplex steam reformer tube. GE was responsible for the development and fabrication of the tube, and KFA was responsible for testing the tube in the EVA I facility at Juelich. Both GE and KFA are evaluating the thermochemical and metallurgical test data. Actual fabrication of the tube was performed by Foster-Wheeler in accordance with the GE design. This paper reviews the highlights of the fabrication development and preliminary evaluation of the test data

Nondestructive testing of multi-layer tubes during fabrication

International Nuclear Information System (INIS)

Troitskij, V.A.; Biletskij, S.M.; Trushchenko, A.A.

1985-01-01

Design of multilayer steel tubes for gas pipelines and technology of their fabrication are described in brief. Testing of the ground metal and welded joints of tubes used in their fabrication are considered. These methods comprise ultrasonic (US) testing of band, US testing and vacuum-bubble testing (VBT) of inner lap joints of shells X-ray TV control (XTVC) of ring welds, US testing of edge sections of shells with a continuous wall. Equipment applied in testing is described. XTVC is exercised by means of the RUP-150/300-10 X-ray apparatus, RI-60TEh introscope, sensitivity of testing is not worse than 4%, the rate equals 1-2 m/min

No rotating U.S. Testing of thin walled tubes

International Nuclear Information System (INIS)

Furlan, J.; Boulanger, G.; Mogavero, R.

1981-07-01

Thin walled tube ultrasonic testing is performed, with Lamb waves, using annular transducers and conical or helicoidal mirrors. The main advantage of this already known system is dispensing with rotation of tube and/or transducer. High speed control (30 cm/s and more) is then allowed. The present paper describes the parameters influencing the sensitivity has been improved by searching, theoretically and practically, the best suited Lamb wave modes, and by using transducers which are well characterized. Practical example of cladding tube U.S. testing is described

Multifrequency eddy current testing of helical tubes of steam generators

International Nuclear Information System (INIS)

Pigeon, M.; David, B.

1983-06-01

In the event of a water-sodium reaction in a steam-generator of a fast breeder reactor, it is necessary to test the tubes close to the leak to evaluate the damage. In SUPERPHENIX, the tubes are about 100m long and are coiled on a dead body. This report describes the equipment and the technic to test such tubes with multifrequency eddy current technics [fr

Feeding Your Baby

Medline Plus

Full Text Available ... care Is it safe? Labor & birth Postpartum care Baby Caring for your baby Feeding your baby Family ... community Home > Baby > Feeding your baby Feeding your baby E-mail to a friend Please fill in ...

Automatic integrated testing bench for tubes in translation

International Nuclear Information System (INIS)

Dufayet, J.P.; Perdijon, J.

1976-01-01

All the nondestructive tests required for receiving the cladding tubes intended for fast nuclear reactor are integrated on this bench: quality control by eddy currents and ultra-sounds, thickness and (inner and outer) diameter measurement. The linear displacement of the tube allows very high rates to be attained [fr

Inert medium (helium) irradiation testing of pressure tube samples

International Nuclear Information System (INIS)

Ancuta, M.; Radu, V.; Stefan, V.; Preda, M.

2001-01-01

Irradiation tests currently performed in C-5 capsule aim at obtaining data and information concerning behavior to irradiation of pressure tubes of CANDU type fuel channel, to evidence the factors limiting operation life span. A calculation code for analysis and prediction of pressure tube behavior should be based upon periodical inspection results, post irradiation examination of the removed from reactor pressure tubes as well as on the experimental results obtained with materials subjected to irradiation conditions identical with the operational ones. Mechanical behavior analysis should focus both complex thermal-mechanical type stresses and mechanical properties alteration under irradiation. The experimental results should be applied: - to evaluate the irradiation effects upon mechanical properties of Zr-2.5% Nb exposed to fluences up to 10 21 n·cm -2 ; - to gather data concerning the real stress / real deformation characteristic from which characteristic quantities can be deduced as, for instance, elasticity modulus, plasticity modulus, exponent of stress term in the Tsu-Berteles relation, to be used within the CANTUP simulation code describing pressure tube behavior, currently developed at INR Pitesti; - to develop prediction methods of pressure tube behavior and merging with in-service inspection procedure in order to forecast the life span and the proper timing for replacement before major failures occur. The samples irradiated in C-5 capsule were extracted from the ends of Zr-2.5% Nb pressure tubes resulting from Cernavoda NPP Unit 1. The samples for tensile tests were extracted on longitudinal and transversal directions of the pressure tube. The tests were carried out under following conditions: - test environment temperature, 260 - 280 deg.C; - testing medium, helium at 1 - 6 b pressure; - neutron flux (E n > 1 MeV), 1 - 2 · 10 13 ncm -2 s -1 ; - neutron fluence (E n > 1 MeV), 4 · 10 20 ncm -2 . The following characteristics were obtained from tensile

Eddy current testing device for metallic tubes at least locally curved

International Nuclear Information System (INIS)

Pigeon, Marcel; Vienot, Claude.

1975-01-01

Steam generators, condensers and heat exchangers generally consist of metallic tube bundles, the tubes having a complex geometry. The invention concerns an Eddy current testing device for metallic tubes at least locally curved, operating by translation of a probe inside the tubes [fr

Influence of test tube material on subcooled flow boiling critical heat flux in short vertical tube

International Nuclear Information System (INIS)

Hata, Koichi; Shiotsu, Masahiro; Noda, Nobuaki

2007-01-01

The steady state subcooled flow boiling critical heat flux (CHF) for the flow velocities (u=4.0 to 13.3 m/s), the inlet subcoolings (ΔT sub,in =48.6 to 154.7 K), the inlet pressure (P in =735.2 to 969.0 kPa) and the increasing heat input (Q 0 exp(t/τ), τ=10, 20 and 33.3 s) are systematically measured with the experimental water loop. The 304 Stainless Steel (SUS304) test tube of inner diameter (d=6 mm), heated length (L=66 mm) and L/d=11 with the inner surface of rough finished (Surface roughness, Ra=3.18 μm), the Cupro Nickel (Cu-Ni 30%) test tube of d=6 mm, L=60 mm and L/d=10 with Ra=0.18 μm and the Platinum (Pt) test tubes of d=3 and 6 mm, L=66.5 and 69.6 mm, and L/d=22.2 and 11.6 respectively with Ra=0.45 μm are used in this work. The CHF data for the SUS304, Cu-Ni 30% and Pt test tubes were compared with SUS304 ones for the wide ranges of d and L/d previously obtained and the values calculated by the authors' published steady state CHF correlations against outlet and inlet subcoolings. The influence of the test tube material on CHF is investigated into details and the dominant mechanism of subcooled flow boiling critical heat flux is discussed. (author)

Influence of Test Tube Material on Subcooled Flow Boiling Critical Heat Flux in Short Vertical Tube

International Nuclear Information System (INIS)

Koichi Hata; Masahiro Shiotsu; Nobuaki Noda

2006-01-01

The steady state subcooled flow boiling critical heat flux (CHF) for the flow velocities (u = 4.0 to 13.3 m/s), the inlet subcooling (ΔT sub,in = 48.6 to 154.7 K), the inlet pressure (P in = 735.2 to 969.0 kPa) and the increasing heat input (Q 0 exp(t/t), t = 10, 20 and 33.3 s) are systematically measured with the experimental water loop. The 304 Stainless Steel (SUS304) test tubes of inner diameters (d = 6 mm), heated lengths (L = 66 mm) and L/d = 11 with the inner surface of rough finished (Surface roughness, R a = 3.18 μm), the Cupro Nickel (Cu-Ni 30%) test tubes of d = 6 mm, L = 60 mm and L/d = 10 with R a = 0.18 μm and the Platinum (Pt) test tubes of d = 3 and 6 mm, L = 66.5 and 69.6 mm, and L/d 22.2 and 11.6 respectively with R a = 0.45 μm are used in this work. The CHF data for the SUS304, Cu-Ni 30% and Pt test tubes were compared with SUS304 ones for the wide ranges of d and L/d previously obtained and the values calculated by the authors' published steady state CHF correlations against outlet and inlet subcooling. The influence of the test tube material on CHF is investigated into details and the dominant mechanism of subcooled flow boiling critical heat flux is discussed. (authors)

Delayed hydrogen cracking test design for pressure tubes

International Nuclear Information System (INIS)

Haddad, Roberto; Loberse, Antonio N.; Yawny, Alejandro A.; Riquelme, Pablo

1999-01-01

CANDU nuclear power stations pressure tubes of alloy Zr-2,5 % Nb present a cracking phenomenon known as delayed hydrogen cracking (DHC). This is a brittle fracture of zirconium hydrides that are developed by hydrogen due to aqueous corrosion on the metal surface. This hydrogen diffuses to the crack tip where brittle zirconium hydrides develops and promotes the crack propagation. A direct current potential decay (DCPD) technique has been developed to measure crack propagation rates on compact test (CT) samples machined from a non irradiated pressure tube. Those test samples were hydrogen charged by cathodic polarization in an acid solution and then pre cracked in a fatigue machine. This technique proved to be useful to measure crack propagation rates with at least 1% accuracy for DHC in pressure tubes. (author)

Sirenomelia (Mermaid baby).

Science.gov (United States)

Akhtar, Jamshed; Shaikh, Muhammad Ali; Saleem, Nasir; Taqvi, Syed Raees; Jehan, Yaqoot; Batool, Tayyaba; Zameer, Naima; Mirza, Farhat

2005-11-01

Sirenomelia is a rare anomaly that rarely occurs as an isolated lesion. Several theories have been proposed regarding the etiopathogenesis. In this communication, we report a case of sirenomelia. Our patient was referred to hospital at the age of four hours. On examination, fusion of both lower limbs with hook shaped appendage, attached distally, absent genitalia and absent anal orifice was found. Spine was deficient in sacral region. Upper torso looked normal. Baby also had frothing from mouth. Abdomen was non-distended. Feeding tube no.10 was tried to pass through mouth, which got obstructed at the level of upper esophagus that suggested oesophageal atresia. The skeletogram revealed absence of pelvic bones, sacral agenesis, absent fibulae and fracture of both femora. The patient died at the age of 12 hours.

Field tests of 2- and 40-tube condensers at the East Mesa Geothermal Test Site

Energy Technology Data Exchange (ETDEWEB)

Murphy, R.W.; Domingo, N.

1982-05-01

Two water-cooled isobutane condensers, one with 2 tubes and one with 40 tubes, were subjected to field tests at the East Mesa Geothermal Test Site to assess relative heat transfer performance in both surface evaporator and direct-contact evaporator modes. The five groups of tests established that field performance was below earlier laboratory-determined levels and that direct-contact evaporator mode performance was poorer than that for the surface evaporator mode. In all test situations, fluted condenser tubes performed better than smooth condenser tubes. Cooling water quality had no significant effect on performance, but brine preflash in the direct-contact mode did promote some relative performance improvement. Important implications of these results for binary geothermal power plants are that (1) working-fluid-side impurities can significantly degrade heat transfer performance of the power plant condensers and (2) provisions for minimizing such impurities may be required.

Feasibility Test with a STS304 tube of the Eddy Current Test using a Bobbin Probe for the SMART SG Tube Inspection

International Nuclear Information System (INIS)

Lee, Yoon Sang; Jung, Hyun Kyu; Choung, Yun Hang

2010-01-01

The SMART SG tubes will be made of Alloy 690. The outside diameter will be 17 mm and the thickness will be 2.5 mm. They will be assembled helically around, and their innermost diameter will be about 600 mm and the total length will be about 32 meters. For the sake of safety, SMART SG tubes are designed for use with thick tubes such as 2.5 mm thickness compared to about 1 mm thickness of normal Korean standard pressurized water reactor tubes. Due to using thick tubes such as the 2.5 mm varieties, it was doubted that the Eddy Current Testing Method (ECT) would be a feasible method. Therefore we are trying to check the feasibility of the ECT using the substitute material STS304 tube instead of Alloy 690 tubes with the bobbin type ECT probe. The previous paper reported the feasibility of the ECT using modeling, but this paper will report the preliminary experimental results and comparison with the previous results of the modeling for the STS304 tube

Maintenance of immersion ultrasonic testing on the water tube boiler

International Nuclear Information System (INIS)

Ishiyama, Toru; Kawasaki, Ichio; Miura, Hirohito

2014-01-01

There are 4-boiler in nuclear fuel cycle engineering laboratories (NCL). These boilers have been operated in the long term over 20 years. One of them, the leakage of boiler water was found at one of the generating tubes, and 2 adjoining generating tubes were corroded in Dec, 2011. These generating tubes were investigated by immersion ultrasonic testing (UT) for measure thickness of the tube. As a result, thinner tube was found in a part of a bend and near the water drum. These parts are covered with sulfide deposit, it seems that the generating tubes were corroded by sulfide. (author)

Effects of Oral Stimulation Intervention in Newborn Babies with Cri du Chat Syndrome: Single-Subject Research Design

Directory of Open Access Journals (Sweden)

Mi Kyung Kim

2018-01-01

Full Text Available The purpose of this study is to treat dysphagia in a newborn baby with cri du chat syndrome using an oral stimulation intervention and to examine its effects. The subject of this study was a baby born 2 weeks prematurely. Since birth, his oxygen saturation (SaO2 decreased while feeding, and he had difficulty with mouth feeding. Thus, an NG feeding tube was inserted, and dysphagia treatment was initiated on the sixth day after birth. A baseline phase and an intervention phase were performed using an AB design. The oral stimulation intervention was not performed in the baseline phase, as only nonnutritive sucking training using a rubber pacifier was used during the baseline phase. During the intervention phase, nonnutritive sucking training and oral stimulation intervention were simultaneously conducted. After the intervention period, daily oral milk intake and intake per feeding of the subject noticeably increased. The oxygen saturation while feeding rose over 90% on average, and the baby did not present with hypoxia. The oral stimulation intervention provided prior to feeding resulted in highly positive effects, including induced normal development of the baby, stimulation of his transition from the NG feeding tube to bottle feeding, increased oxygen saturation, and a shortened hospital stay.

Phthalates in baby skin care products.

Science.gov (United States)

Lampel, Heather P; Jacob, Sharon E

2011-01-01

The systemic toxicity of phthalates has been extensively reported. Although rarely sensitizing, phthalates have been implicated in promoting the development of both atopy and contact dermatitis in animal models. Dermal absorption of phthalates may contribute to overall chemical burden. Infants may be particularly susceptible to chemical exposures. Baby skin care products may be a significant source of phthalate exposure. We measured the phthalate content of 30 skin care products intended for babies and children. Nineteen leave-on and 11 wash-off baby skin care products were analyzed for 17 unique phthalates by an independent laboratory using standard gas chromatographic mass spectrometry. Of 30 products tested, four had phthalate levels above the reporting limit (0.1-0.5 ppm); of these, only one had levels above 1 ppm (44 ppm). There was no statistical significance of phthalate detection in leave-on versus wash-off products (p = .578). The majority (26 of 30) of the baby skin care products analyzed did not have detectable phthalate levels. Four products had detectable phthalate levels. In baby skin care products, levels of the 17 phthalates tested are low overall, but occasional products may contain higher phthalate levels. Monitoring products to ensure safety standards are met may be warranted.

Internal ultrasonic testing of steam generator tubes

International Nuclear Information System (INIS)

Furlan, J.; Soleille, G.; Chalaye, H.

1983-01-01

The ''in situ'' inspection of steam generator tubes uses generally Foucault currents before starting and along its life. This inspection aims at searching cracks and corrosion defects. The Foucault current method is quite badly adapted to ''closed crack'' detection, for it doesn't introduce neither resistivity or magnetic permeability variation, or lack of matter. More, it is sensible to the magnetic properties of the tube itself and to its environment (tubular or support plates). It is why, this first systematic inspection has to be completed by an ultrasonic one allowing to bring new elements in the uncertain cases. A device with an internal probe has been developed. It ''lights'' the tube wall with the aid of a transducer of which beam reflects on a mirror. Operating conditions are the same as for Foucault current testing, that is to say the probe moves inside the tube without rotation of the device (bent parts are excluded) [fr

Surveillance test of OWL-2 inpile tube

International Nuclear Information System (INIS)

Shimizu, Masatsugu; Itoh, Noboru

1976-08-01

A series of irradiation surveillance tests performed in integrity evaluation of an inpile tube for the test loop OWL-2 are described. Specimens were exposed to the neutron fluences from 1 x 10 20 to 3.4 x 10 21 n/cm 2 (>1 MeV), and subjected to post-irradiation tensile test at room temperature and service temperature 285 0 C. The strength increased and the ductility decreased with increasing neutron fluence. The reduction in fracture ductility due to neutron irradiation in the fluence range was insignificant, and the elongation of 33% was retained even for the maximum neutron fluence at 285 0 C. Little decrease of the ductility with fluence indicates that the tube would be in service for long time, ie to the integral fluence of 3.4 x 10 21 n/cm 2 . (auth.)

Bulge testing of copper and niobium tubes for hydroformed RF cavities

Energy Technology Data Exchange (ETDEWEB)

Kim, H.S., E-mail: kim.3237@osu.edu [Department of Materials Science and Engineering, The Ohio State University, Columbus, OH (United States); Sumption, M.D. [Department of Materials Science and Engineering, The Ohio State University, Columbus, OH (United States); Susner, M.A. [Department of Materials Science and Engineering, The Ohio State University, Columbus, OH (United States); Oak Ridge National Laboratory, Oak Ridge, TN (United States); Lim, H. [Department of Materials Science and Engineering, The Ohio State University, Columbus, OH (United States); Sandia National Laboratories, Albuquerque, NM (United States); Collings, E.W. [Department of Materials Science and Engineering, The Ohio State University, Columbus, OH (United States)

2016-01-27

The heat treatment, tensile testing, and bulge testing of Cu and Nb tubes has been carried out to gain experience for the subsequent hydroforming of Nb tube into seamless superconducting radio frequency (SRF) cavities for high energy particle acceleration. In the experimental part of the study samples removed from representative tubes were prepared for heat treatment, tensile testing, residual resistance ratio measurement, and orientation imaging electron microscopy (OIM). After being optimally heat treated Cu and Nb tubes were subjected to hydraulic bulge testing and the results analyzed. In the final part of the study finite-element models (FEM) incorporating constitutive (stress–strain) relationships analytically derived from the tensile and bulge tests, respectively, were used to replicate the bulge test. As expected, agreement was obtained between the experimental bulge parameters and the FEM model based on the bulge-derived constitutive relationship. Not so for the FEM model based on tensile-test data. It is concluded that a constitutive relationship based on bulge testing is necessary to predict a material's performance under hydraulic deformation.

Bulge testing of copper and niobium tubes for hydroformed RF cavities

International Nuclear Information System (INIS)

Kim, H.S.; Sumption, M.D.; Susner, M.A.; Lim, H.; Collings, E.W.

2016-01-01

The heat treatment, tensile testing, and bulge testing of Cu and Nb tubes has been carried out to gain experience for the subsequent hydroforming of Nb tube into seamless superconducting radio frequency (SRF) cavities for high energy particle acceleration. In the experimental part of the study samples removed from representative tubes were prepared for heat treatment, tensile testing, residual resistance ratio measurement, and orientation imaging electron microscopy (OIM). After being optimally heat treated Cu and Nb tubes were subjected to hydraulic bulge testing and the results analyzed. In the final part of the study finite-element models (FEM) incorporating constitutive (stress–strain) relationships analytically derived from the tensile and bulge tests, respectively, were used to replicate the bulge test. As expected, agreement was obtained between the experimental bulge parameters and the FEM model based on the bulge-derived constitutive relationship. Not so for the FEM model based on tensile-test data. It is concluded that a constitutive relationship based on bulge testing is necessary to predict a material's performance under hydraulic deformation.

Thin tube testing by eddy currents

International Nuclear Information System (INIS)

David, Bernard; Pigeon, Michel

1981-01-01

It is often necessary to define test conditions in eddy current testing, in consequence rules and laws allowing a rapid choice of these conditions are welcome. The similarity law, given by Forster, using the reduced frequency f/fg, allows extrapolation of results from an object to one another, if these two objects are similar (i.e. all their dimensions are proportional). In a particular case, often met, a law going further is given to describe, in a sole way, eddy current behaviour using the reduced frequency in all thin tubes (internal to external diameter ratio between 0.85 to 1). For instance working at f/fe=2 defines the same verification leading to identical results, whatever the nature, the diameter or the thickness may be, if the tubes are thin. A diagram is given and a slide-rule, based on this principle, has been realized [fr

Testing and analysis of tube voltage and tube current in the radiation generator for mammography

International Nuclear Information System (INIS)

Jung, Hong Ryang; Hong, Dong Hee; Han, Beom Hui

2014-01-01

Breast shooting performance management and quality control of the generator is applied to the amount of current IEC(International Electrotechnical Commission) 60601-2-45 tube voltage and tube current are based on standards that were proposed in the analysis of the test results were as follows. Tube voltage according to the value of the standard deviation by year of manufacture from 2001 to 2010 as a 42-3.15 showed the most significant, according to the year of manufacture by tube amperage value of the standard deviation to 6.38 in the pre-2000 showed the most significant , manufactured after 2011 the standard deviation of the devices, the PAE(Percent Average Error) was relatively low. This latest generation device was manufactured in the breast of the tube voltage and tube diagnosed shooting the correct amount of current to maintain the performance that can be seen. The results of this study as the basis for radiography diagnosed breast caused by using the device's performance and maintain quality control, so the current Food and Drug Administration 'about the safety of diagnostic radiation generator rule' specified in the test cycle during three years of self-inspection radiation on a radiation generating device ensure safety and performance of the device using a coherent X-ray(constancy) by two ultimately able to keep the radiation dose to the public to reduce the expected effect is expected

Eddy current test of fin tubes for a heat exchanger

International Nuclear Information System (INIS)

KIm, Young Joo; Lee, Se Kyung; Chung, Min Hwa

1992-01-01

Eddy current probes were designed for the test of fin tubes. Fin tubes, often used for heat exchangers, have uneven outer and inner surfaces to enhance the heat emission. The surface roughness make it difficult to detect flaws employing eddy current test(ECT). In order to overcome the difficulties we performed two types of works, one is the delopment of ECT probes, and the other is the signal processing including fast Fourier transform and digital filtering. In the development of ECT probes, we adopted empirical design method. Our ECT probes for fin tubes are inside diameter type. And we are specially concerned about geometric features such as the widths of the coils composing an ECT probe. We fabricated four probes with various coil widths. Eddy current test was performed using those ECT probes on specimens with artificial flaws. After analyzing the output signals, we found that, in order for the effective testing, the width of a coil should be determined considering the pitch of the fins of a tube. And we also learned that the frequency filtering could improve the s/n ratio.

Feeding Your Baby

Medline Plus

Full Text Available ... for your baby Feeding your baby Family health & safety Complications & Loss Pregnancy complications Preterm labor & premature birth ... for your baby Feeding your baby Family health & safety Complications & Loss Pregnancy complications Preterm labor & premature birth ...

Feeding Your Baby

Medline Plus

Full Text Available ... our online community Home > Baby > Feeding your baby Feeding your baby E-mail to a friend Please ... been added to your dashboard . Time to eat! Feeding your baby helps her grow healthy and strong. ...

Feeding Your Baby

Medline Plus

Full Text Available ... fitness Prenatal care Is it safe? Labor & birth Postpartum care Baby Caring for your baby Feeding your ... fitness Prenatal care Is it safe? Labor & birth Postpartum care Baby Caring for your baby Feeding your ...

Feeding Your Baby

Medline Plus

Full Text Available ... then get ready for solid foods ! In This Topic Breastfeeding help Breastfeeding is best Food allergies and ... breast pump Baby Feeding your baby Other Baby topics ') document.write(' Caring for your baby ') document.write('') } ') ...

Sensitivity of the improved Dutch tube diffusion test for detection of ...

African Journals Online (AJOL)

The sensitivity of the improved two-tube test for detection of antimicrobial residues in Kenyan milk was investigated by comparison with the commercial Delvo test SP. Suspect positive milk samples (n =244) from five milk collection centers, were analyzed with the improved two-tube and the commercial Delvo SP test as per ...

Feeding Your Baby

Medline Plus

Full Text Available ... In This Topic Breastfeeding help Breastfeeding is best Food allergies and baby Formula feeding How to breastfeed Keeping breast milk safe and healthy Problems and discomforts when breastfeeding Starting your baby on solid foods Using a breast pump Baby Feeding your baby ...

RIA simulation tests using driver tube for ATF cladding

Energy Technology Data Exchange (ETDEWEB)

Cinbiz, Mahmut N. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Brown, N. R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Lowden, R. R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Linton, K. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Terrani, K. A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-07-01

Pellet-cladding mechanical interaction (PCMI) is a potential failure mechanism for accident-tolerant fuel (ATF) cladding candidates during a reactivity-initiated accident (RIA). This report summarizes Fiscal Year (FY) 2017 research activities that were undertaken to evaluate the PCMI-like hoop-strain-driven mechanical response of ATF cladding candidates. To achieve various RIA-like conditions, a modified-burst test (MBT) device was developed to produce different mechanical pulses. The calibration of the MBT instrument was accomplished by performing mechanical tests on unirradiated Generation-I iron-chromium-aluminum (FeCrAl) alloy samples. Shakedown tests were also conducted in both FY 2016 and FY 2017 using unirradiated hydrided ZIRLO™ tube samples. This milestone report focuses on testing of ATF materials, but the benchmark tests with hydrided ZIRLO™ tube samples are documented in a recent journal article.a For the calibration and benchmark tests, the hoop strain was monitored using strain gauges attached to the sample surface in the hoop direction. A novel digital image correlation (DIC) system composed of a single high-speed camera and an array of six mirrors was developed for the MBT instrument to better resolve the failure behavior of samples and to provide useful data for validation of high-fidelity modeling and simulation tools. The DIC system enable a 360° view of a sample’s outer surface. This feature was added to the instrument to determine the precise failure location on a sample’s surface for strain predictions. The DIC system was tested on several silicon carbide fiber/silicon carbide matrix (SiC/SiC) composite tube samples at various pressurization rates of the driver tube (which correspond to the strain rates for the samples). The hoop strains for various loading conditions were determined for the SiC/SiC composite tube samples. Future work is planned to enhance understanding of the failure behavior of the ATF cladding candidates of age

Tagging of Test Tubes with Electronic p-Chips for Use in Biorepositories.

Science.gov (United States)

Mandecki, Wlodek; Kopacka, Wesley M; Qian, Ziye; Ertwine, Von; Gedzberg, Katie; Gruda, Maryann; Reinhardt, David; Rodriguez, Efrain

2017-08-01

A system has been developed to electronically tag and track test tubes used in biorepositories. The system is based on a light-activated microtransponder, also known as a "p-Chip." One of the pressing problems with storing and retrieving biological samples at low temperatures is the difficulty of reliably reading the identification (ID) number that links each storage tube with the database containing sample details. Commonly used barcodes are not always reliable at low temperatures because of poor adhesion of the label to the test tube and problems with reading under conditions of frost and ice accumulation. Traditional radio frequency identification (RFID) tags are not cost effective and are too large for this application. The system described herein consists of the p-Chip, p-Chip-tagged test tubes, two ID readers (for single tubes or for racks of tubes), and software. We also describe a robot that is configured for retrofitting legacy test tubes in biorepositories with p-Chips while maintaining the temperature of the sample below -50°C at all times. The main benefits of the p-Chip over other RFID devices are its small size (600 × 600 × 100 μm) that allows even very small tubes or vials to be tagged, low cost due to the chip's unitary construction, durability, and the ability to read the ID through frost and ice.

Using YouTube to Disseminate Effective Vaccination Pain Treatment for Babies.

Science.gov (United States)

Harrison, Denise; Wilding, Jodi; Bowman, Amanda; Fuller, Ann; Nicholls, Stuart G; Pound, Catherine M; Reszel, Jessica; Sampson, Margaret

2016-01-01

Infant vaccinations are necessary for public health, but are painful, causing distress to the infant and caregivers. Breastfeeding and sucrose effectively reduce infants' pain during vaccinations, and these strategies are recommended in health care provider (HCP)-targeted education and vaccination pain guidelines. However studies show these strategies are infrequently used. YouTube is a popular medium to publicly share and watch videos, and many consumer posted YouTube videos show distressed infants being vaccinated with no pain treatment. The aims of this study were to evaluate the reach and impact of a consumer-targeted YouTube video demonstrating use of effective pain reduction strategies during infant vaccinations. A brief consumer-targeted video showing two infants being vaccinated was posted onto YouTube on October 2013. One infant was breastfed and another infant received sucrose by mouth before and during the injection. A link to a viewer survey was visible on a banner near the end of the video. An intensive strategically planned knowledge dissemination strategy using the media, social media and messages to professional organizations took place to promote the video. Data analysis of the viewer survey, YouTube analytics of the reach of the video in terms of number of views, country of viewers, and comments relating to the video took place 12 months after the video was posted. Twelve months after posting, the video had 65,478views, 68 comments, 245 likes, 17 dislikes, and 90 shares. Average duration of viewer time was 65% of the video. The viewer survey was completed by 156 (0.24%) viewers; 90 (58%) answered as HCPs and 66 (42%) as parents. Survey results showed that the video was persuasive; intent to use or support breastfeeding or sucrose was high in both parents and HCPs after viewing the video. Comments posted were often emotional in nature, and were related to anti-vaccination (n = 26, 38%); effectiveness or positive personal experiences (n = 21, 32

Using YouTube to Disseminate Effective Vaccination Pain Treatment for Babies.

Directory of Open Access Journals (Sweden)

Denise Harrison

Full Text Available Infant vaccinations are necessary for public health, but are painful, causing distress to the infant and caregivers. Breastfeeding and sucrose effectively reduce infants' pain during vaccinations, and these strategies are recommended in health care provider (HCP-targeted education and vaccination pain guidelines. However studies show these strategies are infrequently used. YouTube is a popular medium to publicly share and watch videos, and many consumer posted YouTube videos show distressed infants being vaccinated with no pain treatment. The aims of this study were to evaluate the reach and impact of a consumer-targeted YouTube video demonstrating use of effective pain reduction strategies during infant vaccinations.A brief consumer-targeted video showing two infants being vaccinated was posted onto YouTube on October 2013. One infant was breastfed and another infant received sucrose by mouth before and during the injection. A link to a viewer survey was visible on a banner near the end of the video. An intensive strategically planned knowledge dissemination strategy using the media, social media and messages to professional organizations took place to promote the video. Data analysis of the viewer survey, YouTube analytics of the reach of the video in terms of number of views, country of viewers, and comments relating to the video took place 12 months after the video was posted.Twelve months after posting, the video had 65,478views, 68 comments, 245 likes, 17 dislikes, and 90 shares. Average duration of viewer time was 65% of the video. The viewer survey was completed by 156 (0.24% viewers; 90 (58% answered as HCPs and 66 (42% as parents. Survey results showed that the video was persuasive; intent to use or support breastfeeding or sucrose was high in both parents and HCPs after viewing the video. Comments posted were often emotional in nature, and were related to anti-vaccination (n = 26, 38%; effectiveness or positive personal experiences (n

Feeding Your Baby

Medline Plus

Full Text Available ... In This Topic Breastfeeding help Breastfeeding is best Food allergies and baby Formula feeding How to breastfeed Keeping a breastfeeding log Keeping breast milk safe and healthy Problems and discomforts when breastfeeding Starting your baby on solid foods Using a breast pump Baby Feeding your baby ...

Stress corrosion testing of irradiated cladding tubes

International Nuclear Information System (INIS)

Lunde, L.; Olshausen, K.D.

1980-01-01

Samples from two fuel rods with different cladding have been stress corrosion tested by closed-end argon-iodine pressurization at 320 0 C. The fuel rods with stress relieved and recrystallized Zircaloy-2 had received burnups of 10.000 and 20.000 MWd/ton UO 2 , respectively. It was found that the SCC failure stress was unchanged or slightly higher for the irradiated than for the unirradiated control tubes. The tubes failed consistently in the end with the lowest irradiation dose. The diameter increase of the irradiated cladding during the test was 1.1% for the stress-relieved samples and 0.24% for the recrystallized samples. SEM examination revealed no major differences between irradiated and unirradiated cladding. A ''semi-ductile'' fracture zone in recrystallized material is described in some detail. (author)

Pressure tests to assess the significance of defects in boiler and superheater tubing

International Nuclear Information System (INIS)

Guest, J.C.; Hutchings, J.A.

1975-01-01

Internal pressure tests on 9 per cent Cr-1 per cent Mo steel tubing containing artificial defects demonstrated that the resultant loss of strength was less than a simple calculation based on the reduced tube thickness would suggest. Bursting tests on tubes containing longitudinal defects of varying length, depth and acuity showed notch strengthening at ambient temperature and at 550 0 C. A flow stress concept developed for simple bursting tests was shown to apply to creep conditions at 550 0 C. Results of creep and short-term bursting tests show that the length as well as the depth of the defect is an important factor affecting the life of bursting strength of the tubes. Defects less than 10 per cent of the tube thickness were found to have an insignificant effect. (author)

Remote field eddy current testing of ferromagnetic tubes

International Nuclear Information System (INIS)

David, B.

1990-01-01

In order to test ferromagnetic tubes using internal probes, Intercontrole and the CEA have carried out theoretical and experimental works and developed a method to adapt the Remote Field Eddy Current technique which has been known and used for 30 years now. This document briefly recalls the basic principles of the Remote Field Eddy Current technique, the various steps of the works carried out and mainly describes examples of field inspection of ferromagnetic tubes and pipes [fr

Test bench HEATREC for heat loss measurement on solar receiver tubes

Science.gov (United States)

Márquez, José M.; López-Martín, Rafael; Valenzuela, Loreto; Zarza, Eduardo

2016-05-01

In Solar Thermal Electricity (STE) plants the thermal energy of solar radiation is absorbed by solar receiver tubes (HCEs) and it is transferred to a heat transfer fluid. Therefore, heat losses of receiver tubes have a direct influence on STE plants efficiency. A new test bench called HEATREC has been developed by Plataforma Solar de Almería (PSA) in order to determinate the heat losses of receiver tubes under laboratory conditions. The innovation of this test bench consists in the possibility to determine heat losses under controlled vacuum.

Eddy current testing of heat exchangers tubes

International Nuclear Information System (INIS)

Gouez, J.F.; Rieusset, A.; Groix, F.

An automatic system for Eddy Current testing of heat exchangers tubes of warships was developed. The advantages are an exposure of the controller limited at the time required to put in place the system and a reduced time of control [fr

'Dodo' and 'Baby Bear' Trenches

Science.gov (United States)

2008-01-01

NASA's Phoenix Mars Lander's Surface Stereo Imager took this image on Sol 11 (June 5, 2008), the eleventh day after landing. It shows the trenches dug by Phoenix's Robotic Arm. The trench on the left is informally called 'Dodo' and was dug as a test. The trench on the right is informally called 'Baby Bear.' The sample dug from Baby Bear will be delivered to the Phoenix's Thermal and Evolved-Gas Analyzer, or TEGA. The Baby Bear trench is 9 centimeters (3.1 inches) wide and 4 centimeters (1.6 inches) deep. The Phoenix Mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development is by Lockheed Martin Space Systems, Denver.

Philips high tension generator (x-ray machine) testing for baby ebm (electron beam machine) project

International Nuclear Information System (INIS)

Norman Awalludin; Leo Kwee Wah; Abu Bakar Mhd Ghazali

2005-01-01

This paper describes the test of the HT system (from X-ray machine) for usage of the mini EBM (Electron Beam Machine). It consists the procedures of the installation, the safety procedures when deals with HT, modification of the system for testing purpose and the technique/method for testing the HT system. As a result, the voltage for the HT system and the electron gun (filament) current can be measured. Based on the results, suitability of the machine for baby EBM could be confirmed. (Author)

Feeding Your Baby

Medline Plus

Full Text Available ... Frequently asked questions Email sign up Join our online community Home > Baby > Feeding your baby Feeding your baby E-mail to a friend Please fill in all fields. Please enter a ...

Breastfeed Your Baby

Science.gov (United States)

... your baby breast milk only (no formula, juice, cow's milk, solid foods, or water). Give your baby ... vitamin D. Babies need vitamin D for healthy bone growth. Even if you take extra vitamin D, ...

Feeding Your Baby

Medline Plus

Full Text Available ... Home > Baby > Feeding your baby Feeding your baby E-mail to a friend Please fill in all fields. Please enter a valid e-mail address. Your information: Your recipient's information: Your ...

Fracture Toughness Round Robin Test International in pressure tube materials

International Nuclear Information System (INIS)

Villagarcia, M.P.; Liendo, M.F.

1993-01-01

Part of the pressure tubes surveillance program of CANDU type reactors is to determine the fracture toughness using a special fracture specimen and test procedure. Atomic Energy of Canada Limited decided to hold a Round Robin Test International and 9 laboratories participated worldwide in which several pressure tube materials were selected: Zircaloy-2, Zr-2.5%Nb cold worked and Zr-2.5%Nb heat treated. The small specimens used held back the thickness and curvature of the tube. J-R curves at room temperature were obtained and the crack extension values were determined by electrical potential drop techniques. These values were compared with results generated from other laboratories and a bid scatter was founded. It could be due to slight variations in the test method or inhomogeneity of the materials and a statistical study must be done to see if there is any pattern. The next step for the Round Robin Test would be to make some modifications in the test method in order to reduce the scatter. (Author)

The efficacy of test tube warming devices used during oocyte retrieval for IVF.

Science.gov (United States)

Yeung, Queenie Sum Yee; Briton-Jones, Christine May; Tjer, Grace Ching Ching; Chiu, Tony Tak Yu; Haines, Christopher

2004-10-01

To investigate whether commonly used test tube warming devices maintain a constant temperature in follicular fluid aspirates. By using a digital thermocouple, temperature was measured and comparisons were made between an analog dry block heater, a digital dry block heater, and a thermostatic test tube heater. For small fluid volumes, temperature in the block heaters increased above 37 degrees C after being in the block for over 2 min. The thermostatic heater maintained a constant temperature, but this was below the factory setting of 36.9 degrees C. Temperature maintenance was influenced by fluid volume in each tube. One of the key factors in the handling of gametes and embryos is the maintenance of constant temperature. Test tube warming devices require verification of their ability to maintain fluid at the desired temperature. Temperature may vary with fluid volume and the type of test tube warming device used.

Feeding Your Baby

Medline Plus

Full Text Available ... questions Email sign up Join our online community Home > Baby > Feeding your baby Feeding your baby E- ... We're working to radically improve the health care they receive. We're pioneering research to find ...

Feeding Your Baby

Medline Plus

Full Text Available ... baby Feeding your baby E-mail to a friend Please fill in all fields. Please enter a ... for your baby during the first year of life. Learn how to breastfeed and why breast milk ...

Feeding Your Baby

Medline Plus

Full Text Available ... Frequently asked questions Email sign up Join our online community March for Babies Nacersano Share Your Story ... Frequently asked questions Email sign up Join our online community Home > Baby > Feeding your baby Feeding your ...

Feeding Your Baby

Medline Plus

Full Text Available ... Baby Caring for your baby Feeding your baby Family health & safety Complications & Loss Pregnancy complications Preterm labor & ... health research Prematurity research centers For providers NICU Family Support® Prematurity Campaign Collaborative Info for your patients ...

Development of ultrasonic testing scanner for NPP steam generator tubes (I)

International Nuclear Information System (INIS)

Shin, J. I.; Huh, H.

1998-12-01

Testing tubes are designed and fabricated to investigate the optimum test conditions through the various experiments. The proto-type P/C-controlled automatic rotating scanner is fabricated to obtain the ultrasonic data automatically from test tubes. It was attempted to visualize the shape of defects presented inside the specimen using peak amplitude at each point. However, further research works will be needed to be applied at the plant site as a more reliable technology

Baby Skyrmion chains

International Nuclear Information System (INIS)

Foster, David

2010-01-01

The Baby Skyrmion model is a two-dimensional analogue of the full three-dimensional Skyrme model. It is not just useful for guiding investigations in the Skyrme model, it also has applications in condensed matter physics. Previous results on multi-charged Baby Skyrmion solutions have pointed to a modular structure, comprised of charge two rings and single charge one Skyrmions, which combine to form higher charged structures. In this paper we present alternative numerical solutions that correspond to new finite Baby Skyrmion chains, which have lower energy than those found previously, and are also good candidates for the global minimum energy solutions. We then proceed from the infinite plane, to Baby Skyrmions on a cylinder and then a torus, to obtain the solutions of periodic Baby Skyrmions, of which periodic segments will correspond to sections of large charge Baby Skyrmions in the plane

Bringing Your Baby Home

Science.gov (United States)

... for Educators Search English Español Bringing Your Baby Home KidsHealth / For Parents / Bringing Your Baby Home What's ... recall your baby's seemingly endless crying episodes. The Home Front Introducing your baby to others at home ...

In-operation testing of condensers tubes in EDF thermal power plants

International Nuclear Information System (INIS)

Sermadiras, P.; Cormier, J.

1982-01-01

Electricite de France requires manufacturers to perform a number of tests on condenser tubes, as it does itself, including eddy current tests. This article describes the worksite inspection procedures, which use internal single-frequency probes to detect the following irregularities: - in differential mode: external corrosion, impacts, foreign matter, vibrations, internal behaviour of tubes; - in absolute mode: corrosion by ammonia [fr

Garter spring location of pressure tube for PHWR using eddy current testing methods

International Nuclear Information System (INIS)

Lee, Y. S.; Yang, D. J.; Jeong, H. K.

2001-01-01

There are garter springs between pressure tube and calandria tube for PHWR. If the space of these garter springs become to be changed, the sagging of tube is caused and the contact between the pressure tube and calandria tube will cause the tube to be failed. AECL has applied the eddy current testing methods using send-receive type probe for this purpose, but this study apply eddy current testing methods using bobbin differential type probe to detection of garter spring location. And we did the computer simulation using VIC-3D code and compared it with experiments results for inspection 1 ∼ 11kHz. The results was that the garter spring signal was successfully detected for every frequency, and 5 kHz was best

Basic data report for borehole Cabin Baby-1 deepening and hydrologic testing. Waste Isolation Pilot Plant (WIPP) project, southeastern New Mexico

International Nuclear Information System (INIS)

Beauheim, R.L.; Hassinger, B.W.; Klaiber, J.A.

1983-12-01

Borehole Cabin Baby-1 was originally drilled to a depth of 4159.0 feet below kelly bushing (8.0 feet above ground surface) in 1974 and 1975 as a ''wildcat'' hydrocarbon exploratory well. Control of the borehole was given to the US Department of Energy (DOE) after it was found to be a ''dry hole''. Cabin Baby-1 was reentered, deepened, and hydrologically tested in August and September 1983. The well is located in Section 5, T23S, R31E, just outside the limit of WIPP Zone III, approximately 2.5 miles south of the WIPP exploratory shaft. The deepening and testing of Cabin Baby-1 was undertaken for several reasons: to provide data on the hydrologic properties, including hydrostatic head potential of selected permeable zones in the Bell Canyon Formation; to provide representative fluid samples from selected permeable zones in the Bell Canyon Formation for determination of fluid composition and density; and to define further the stratigraphy of the upper Bell Canyon Formation at the Cabin Baby-1 location. The borehole was deepened from the previous total depth to a new depth of 4298.6 feet below kelly bushing by continuous coring. Field operations related to deepening and logging of the borehole began August 12, 1983 and were completed August 30, 1983. Hydrologic testing activities began August 30, 1983 and were completed September 29, 1983. Drill-stem tests were conducted in four zones in the Bell Canyon Formation, and one test of the Salado Formation was performed. Fluid samples were collected from the Hays and Olds sandstones of the Bell Canyon Formation

Using a Bedside Video-assisted Test Tube Test to Assess Stoma Viability: A Report of 4 Cases.

Science.gov (United States)

Ahmad, Sarwat; Turner, Keli; Shah, Paulesh; Diaz, Jose

2016-07-01

Mucosal discoloration of an intestinal stoma may indicate self-limited venous congestion or necrosis necessitating operative revision. A common bedside technique to assess stoma viability is the "test tube test". A clear tube is inserted into the stoma and a hand-held light is used to assess the color of the stoma. A technique (video-assisted test tube test [VATTT]) developed by the authors utilizes a standard video bronchoscope inserted into a clear plastic blood collection tube to visually inspect and assess the mucosa. This technique was evaluated in 4 patients (age range 49-72 years, all critically ill) with a discolored stoma after emergency surgery. In each case, physical exam revealed ischemic mucosa at the surface either immediately after surgery or after worsening hypotension weeks later. Serial test tube test assessments were ambiguous when trying to assess deeper mucosa. The VATTT assessment showed viable pink mucosa beneath the surface and until the fascia was revealed in 3 patients. One (1) patient had mucosal ischemia down to the fascia, which prompted operative revision of the stoma. The new stoma was assessed with a VATTT and was viable for the entire length of the stoma. VATTT provided an enhanced, magnified, and clearer way to visually assess stoma viability in the postoperative period that can be performed at the bedside with no adverse events. It may prevent unnecessary relaparotomy or enable earlier diagnosis of deep ostomy necrosis. Validity and reliability studies are warranted.

Predictors of hepatitis C testing intention among African American Baby Boomers

Directory of Open Access Journals (Sweden)

Mohamed Rashrash

2017-06-01

Full Text Available Baby Boomers (BBs are responsible for three-quarters of hepatitis C virus (HCV infections in the United States; however, HCV testing is distinctly underused by them. A cross-sectional study was conducted to assess the prevalence of HCV testing and to evaluate predictors of HCV testing intention among African–American BBs. The study was guided by the Health Belief Model and theory of reasoned action frameworks. Of the 137 participants included in the study, 44.8% had at least a college education; 13.9% received prior to 1992 blood transfusion. Findings related to HCV testing showed that 32.1% of the participants intended to test for HCV within 6 months and 43.8% had received a previous HCV test. Significant predictors of HCV testing intention within 6 months included having a blood transfusion prior to 1992 [odds ratio (OR = 8.25, 95% confidence interval (CI: 2.02–33.61], perceptions of benefits (OR = 1.57, 95% CI: 1.13–2.18, severity (OR = 1.39, 95% CI: 1.17–1.65, and subjective norms (OR = 1.42, 95% CI: 1.12–1.79. These predictors of HCV testing intention can be used to develop future HCV testing initiatives for African–American BBs.

Feeding Your Baby

Medline Plus

Full Text Available ... baby formula , find out how to choose the best one for your baby and how to make bottle-feeding safe. And then get ready for solid foods ! In This Topic Breastfeeding help Breastfeeding is best Food allergies and baby Formula feeding How to ...

SCC testing of steam generator tubes repaired by welded sleeves

International Nuclear Information System (INIS)

Pierson, E.; Stubbe, J.

1993-01-01

One way to repair steam generator tubing is to introduce a sleeve inside the tube so that it spans the corroded area and to seal it at both ends. This technique has been studied at Laborelec with a particular attention paid to the occurrence of new SCC cracks at the upper joint. Tube segments coming from the same lot of mill annealed alloy 600 were sent to six manufacturers to be sleeved by their own procedure (including TIG, laser or kinetic welding, followed or not by a stress relief heat treatment), and then tested at Laborelecin 10% NaOH at 350 degrees C. The tests were performed with and without differential pressure i.e. in capsules (Δ = 9 and 19 MPa) and in autoclave (Δp = 0). Nearly all the not stress relieved mock-ups developed through cracks in several hundred hours in auto-clave. The cracks were circumferential and situated near the weld. At 9 and 19 MPa, the time to failure decreased and longitudinal cracks appeared near the weld and at the transition zone of expanded areas. Cracks were never observed in the alloy 690 sleeve, except in the weld bead. Reference capsules (roll expaned tubes) made of the same lot of alloy 600 were tested in the same environment

Experimental Investigation of Reynolds Number Effects on Test Quality in a Hypersonic Expansion Tube

Science.gov (United States)

Rossmann, Tobias; Devin, Alyssa; Shi, Wen; Verhoog, Charles

2017-11-01

Reynolds number effects on test time and the temporal and spatial flow quality in a hypersonic expansion tube are explored using high-speed pressure, infrared optical, and Schlieren imaging measurements. Boundary layer models for shock tube flows are fairly well established to assist in the determination of test time and flow dimensions at typical high enthalpy test conditions. However, the application of these models needs to be more fully explored due to the unsteady expansion of turbulent boundary layers and contact regions separating dissimilar gasses present in expansion tube flows. Additionally, expansion tubes rely on the development of a steady jet with a large enough core-flow region at the exit of the acceleration tube to create a constant velocity region inside of the test section. High-speed measurements of pressure and Mach number at several locations within the expansion tube allow for the determination of an experimental x-t diagram. The comparison of the experimentally determined x-t diagram to theoretical highlights the Reynolds number dependent effects on expansion tube. Additionally, spatially resolved measurements of the Reynolds number dependent, steady core-flow in the expansion tube viewing section are shown. NSF MRI CBET #1531475, Lafayette College, McCutcheon Foundation.

Feeding Your Baby

Medline Plus

Full Text Available ... bond with her. Breast milk is the best food for your baby during the first year of life. Learn how to breastfeed and why breast milk is so good for babies. You and your baby may need time and practice to get comfortable breastfeeding, but you’ll get ...

Interactive baby feeding bottle

NARCIS (Netherlands)

2013-01-01

An interactive baby bottle with an electronic unit is disclosed. The electronic unit comprises a sensor unit configured to sense the heart beat of a person bottle feeding a baby and an actuator unit configured to transmit the sensed heart beat to the baby. The disclosed interactive baby bottle can

Development of a sealing process of capsules for surveillance test tubes of the vessel in nuclear power plants

International Nuclear Information System (INIS)

Romero C, J.; Fernandez T, F.; Perez R, N.; Rocamontes A, M.; Garcia R, R.

2007-01-01

The surveillance capsule is composed by the support, three capsules for impact test tubes, five capsules for tension test tubes and one porta dosemeters. The capsules for test tubes are of two types: rectangular capsule for Charpy test tubes and cylindrical capsule for tension test tubes. This work describes the development of the welding system to seal the capsules for test tubes that should contain helium of ultra high purity to a pressure of 1 atmosphere. (Author)

Food allergy in breastfeeding babies. Hidden allergens in human milk.

Science.gov (United States)

Martín-Muñoz, M F; Pineda, F; García Parrado, G; Guillén, D; Rivero, D; Belver, T; Quirce, S

2016-07-01

Food allergy is a rare disorder among breastfeeding babies. Our aim was to identify responsible allergens in human milk. We studied babies developing allergic symptoms at the time they were breastfeeding. Skin prick tests (SPT) were performed with breast milk and food allergens. Specific IgE was assessed and IgE Immunoblotting experiments with breast milk were carried out to identify food allergens. Clinical evolution was evaluated after a maternal free diet. Five babies had confirmed breast milk allergy. Peanut, white egg and/or cow's milk were demonstrated as the hidden responsible allergens. No baby returned to develop symptoms once mother started a free diet. Three of these babies showed tolerance to other food allergens identified in human milk. A maternal free diet should be recommended only if food allergy is confirmed in breastfed babies.

Performance demonstration tests for eddy current inspection of steam generator tubing

International Nuclear Information System (INIS)

Kurtz, R.J.; Heasler, P.G.; Anderson, C.M.

1996-05-01

This report describes the methodology and results for development of performance demonstration tests for eddy current (ET) inspection of steam generator tubes. Statistical test design principles were used to develop the performance demonstration tests. Thresholds on ET system inspection performance were selected to ensure that field inspection systems would have a high probability of detecting and and correctly sizing tube degradation. The technical basis for the ET system performance thresholds is presented in detail. Statistical test design calculations for probability of detection and flaw sizing tests are described. A recommended performance demonstration test based on the design calculations is presented. A computer program for grading the probability of detection portion of the performance demonstration test is given

Performance demonstration tests for eddy current inspection of steam generator tubing

Energy Technology Data Exchange (ETDEWEB)

Kurtz, R.J.; Heasler, P.G.; Anderson, C.M.

1996-05-01

This report describes the methodology and results for development of performance demonstration tests for eddy current (ET) inspection of steam generator tubes. Statistical test design principles were used to develop the performance demonstration tests. Thresholds on ET system inspection performance were selected to ensure that field inspection systems would have a high probability of detecting and and correctly sizing tube degradation. The technical basis for the ET system performance thresholds is presented in detail. Statistical test design calculations for probability of detection and flaw sizing tests are described. A recommended performance demonstration test based on the design calculations is presented. A computer program for grading the probability of detection portion of the performance demonstration test is given.

Feeding Your Baby

Medline Plus

Full Text Available ... food for your baby during the first year of life. Learn how to breastfeed and why breast milk is so good for babies. You and your baby may need time and practice to get comfortable breastfeeding, but you’ll get the hang of it! Don’t be afraid to ask for ...

Design of experiments and equipment to test the ballooning characteristics of CANDU pressure tubes

International Nuclear Information System (INIS)

Forrest, C.F.; Stern, F.; Hart, R.G.

1992-01-01

Experiments have been planned and an apparatus has been designed to enable creep testing of end-of-life pressure tube specimens in a LOCA environment. Effects that could be studied include: annealing of irradiation damage during transient heating; effects of hydride blisters on pressure tube ballooning strains; and, effects of uniformly-distributed hydrogen content on pressure tube ballooning strains. The proposed experimental program will consist of separate effects creep tests on pressure tube sections under transient heating conditions

Are baby hammocks safe for sleeping babies? A randomised controlled trial.

Science.gov (United States)

Chiu, Karen; Tonkin, Shirley L; Gunn, Alistair J; McIntosh, Christine C

2014-07-01

Two reports of infants found dead after sleeping in baby hammocks have raised international concern about the safety of infant hammocks. We therefore tested whether hammock sleep affected oxygenation in infants, when they were at an age of high risk of sudden, unexpected infant death. Healthy, full-term 4- to 8-week-old infants were randomised to sleep either in a commercially available hammock (n = 14) or a standard bassinet (n = 9), and sleep state, oxygen desaturation (a fall in peripheral haemoglobin oxygen saturation (SpO2 ) ≥ 4%, for ≥ 4 sec from baseline to nadir), apnoea and hypopnoea, and mean SpO2 were analysed. There was no significant difference in mean SpO2 (both 98.5%) or rate of oxygen desaturation events between the hammock and the bassinet cot (mean ± SD, 24 ± 20 vs. 28 ± 23 events per hour), but infants slept less in the hammock (59 ± 31 vs. 81 ± 34 min, p baby hammocks, nor to older babies, particularly once the infant can roll. Given that it is not possible to predict when an infant will be able to roll, we strongly recommend that hammocks should not be used for unsupervised sleep. ©2014 Foundation Acta Paediatrica. Published by John Wiley & Sons Ltd.

Optimum Frequency for Eddy Current Testing Method of SMART SG tubes

International Nuclear Information System (INIS)

Lee, Yoon Sang; Jung, Hyun Kyu; Choung, Yun Hang

2009-01-01

The SMART SG tubes will be made of Alloy 690. The outside diameter will be 17 mm and the thickness will be 2.5 mm. They will be assembled helically around, and their innermost diameter will be about 600 mm and the total length will be about 32 meters. For safety, SMART SG tubes are designed for use with thick tubes such as 2.5 mm thickness compared to about 1 mm thickness of normal Korean standard pressurized water reactor tubes. Due to using thick tubes such as 2.5 mm varieties, it was doubted that the Eddy Current Testing Method (ECT) would be a feasible method. Therefore we are trying to simulate the bobbin probe signal for SMART SG tubes and comparing it to PWR SG ECT probe signal using VIM software, checking for the applicability of ECT. Also we are trying to compare the ECT signal of 2.5 mm thick stainless tubes to check if they are possible substitute material

Assessment of Irritation and Sensitization Potential of Eight Baby Skin Care Products.

Science.gov (United States)

Galzote, Carlos; Thomas, Mini; Sachdev, Mukta

2016-10-01

Ethnic differences in skin sensitivity suggest that greater emphasis be focused on understanding a product's effect in diverse populations. The irritation and/or sensitization potential of 8 baby skin care products in Indian adults were evaluated using cumulative irritation tests (CIT) and human repeat insult patch testing (HRIPT) protocols. Healthy males or females aged 18 to 65 years of Indian ethnicity were treated with each of 6 products (cream, hair oil, lotion, body wash, shampoo, and baby soap) using CIT (n = 25) and HRIPT (n = 200). Baby powder and baby oil were evaluated by CIT (n = 25) and HRIPT (n = 107) in separate studies. CITs were conducted over 14 days; HRIPTs were conducted over 10 weeks. In both CIT and HRIPT, most products were considered mild, with no irritation. Baby soap and powder elicited reactions in the HRIPT induction phase, with positive challenge phase reactions (3 subjects), but were affirmed to be nonallergenic in the rechallenge phase. In these studies, 8 baby skin care products were evaluated by both CIT and HRIPT in Indian adults. The results of the studies indicated that all of the tested products were nonallergenic and nonirritating. J Drugs Dermatol. 2016;15(10):1244-1248.

Of Slot Machines and Broken Test Tubes

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 19; Issue 5. Of Slot Machines and Broken Test Tubes. S Mahadevan. General Article Volume 19 Issue 5 May 2014 pp 395-405. Fulltext. Click here to view fulltext PDF. Permanent link: https://www.ias.ac.in/article/fulltext/reso/019/05/0395-0405. Keywords.

Adaptation, testing and application of the two-dimensional FE computer program system for steam generator tube testing

International Nuclear Information System (INIS)

Betzold, K.

1987-01-01

The 2d-FE computing program system, taken over by EPRI, is used for the improvement of the eddy current test of steam generator heating tubes. The investigations focus on test tasks in the area of the tube plate and the scrap mark; among them: accumulation of mud in the cracking area and above the tube plate; circulating slots with and without accumulation of mud. The interaction of the factors of influence given by the test object and the parameters selectable by the tester as for example coil length and base space for absolute coils and differential coils as well as test frequencies are calculated and the form of the signal locus curves and the dynamic curves are listed in a sample catalogue. It is demonstrated with selected examples that the sample catalogue contributes to the test-specific design of the coil and to the choice of the test frequencies; interpretation of measured signals; deepening of the knowledge of the physical processe in eddy current tests. (orig./HP) [de

A blind test on the pulse tube refrigerator model (PTRM)

International Nuclear Information System (INIS)

Yuan, S.W.K.; Radebaugh, R.

1996-01-01

The Stirling Refrigerator Performance Model (SRPM) has been validated extensively against the Lockheed built Stirling Coolers and various units in the literature. This model has been modified to predict the performance of the Pulse Tube Coolers (PTCs). It was successfully validated against a Lockheed in-house-built PTC. The results are to be published elsewhere. In this paper, the validation of PTRM against a NIST (National Institute of Standards and Technology) orifice pulse tube cooler is reported. Dimensions and operating condition of the PTC were obtained from NIST without prior knowledge of the performance. In other words, this is a open-quote blind test close-quote on the PTRM with the help of the National Institute of Standards and Technology. Good correlation was found between the test data and the prediction. PTRM is a generic model that gives accurate performance prediction of the pulse tube coolers

Baby supplies you need

Science.gov (United States)

Newborn care - baby supplies ... wintertime. Mobile. This can entertain and distract a baby who is fussy or is having a hard ... rainfall). These sounds can be soothing for the baby and can help him sleep.

Can Babies Learn to Read? A Randomized Trial of Baby Media

Science.gov (United States)

Neuman, Susan B.; Kaefer, Tanya; Pinkham, Ashley; Strouse, Gabrielle

2014-01-01

Targeted to children as young as 3 months old, there is a growing number of baby media products that claim to teach babies to read. This randomized controlled trial was designed to examine this claim by investigating the effects of a best-selling baby media product on reading development. One hundred and seventeen infants, ages 9 to 18 months,…

The New Baby.

Science.gov (United States)

Brain, Helen

This book for beginning readers tells the story of a South African priest and his wife who are ashamed when their daughter tells them she is going to have a baby. They refuse to have anything to do with her when she is pregnant. However, when the baby comes, everything changes and they come to accept and love the baby. Large black and white…

Non-destructive testing of tubes by electromagnetic processes

International Nuclear Information System (INIS)

Kowarski, A.

1979-01-01

This article reviews and assesses the non destructive testing techniques used for locating defects in tubes by electromagnetic processes. These form the basis of many testing devices, the diversity of which results from various factors: range of materials, methods of fabrication, specific defects of the product. There are two distinct main families of devices utilising two different principles: dispersion flow and Foucault currents [fr

Your Baby's Growth: 12 Months

Science.gov (United States)

... Safe Videos for Educators Search English Español Your Baby's Growth: 12 Months KidsHealth / For Parents / Your Baby's ... doubled his or her birth weight. Is My Baby Growing Normally? Babies' growth begins to slow as ...

Your Baby's Growth: 5 Months

Science.gov (United States)

... Safe Videos for Educators Search English Español Your Baby's Growth: 5 Months KidsHealth / For Parents / Your Baby's ... a cause for concern. How Much Will My Baby Grow? By 5 months, your baby's birth weight ...

Fretting wear of steam generator tubes: high-temperature tests on AECL rig

International Nuclear Information System (INIS)

Guerout, F.; Zbinden, M.

1993-07-01

The R and DD has undertaken the study of fretting-wear of Alloy 600 S.G. tubes which occurs by contact with migrating items. The test series was performed in Canada at AECL Research (Atomic Energy of Canada Limited) as part of an exchange program. Four types of configuration were envisaged: a tube-to-drilled hole support contact which provides reference results and three types of tube-to-support contacts which simulate the tube fretting-wear induced by a welding rod, a threaded rod and a knife-edge rod support. This programme is completed by the study of the contact between a S.G. tube and a neighbouring S.G. tube which has been broken after plugging. (authors). 1 tab., 3 refs

Controlatron Neutron Tube Test Suite Software Manual - Operation Manual (V2.2)

CERN Document Server

Noel, W P; Hertrich, R J; Martinez, M L; Wallace, D L

2002-01-01

The Controlatron Software Suite is a custom built application to perform automated testing of Controlatron neutron tubes. The software package was designed to allowing users to design tests and to run a series of test suites on a tube. The data is output to ASCII files of a pre-defined format for data analysis and viewing with the Controlatron Data Viewer Application. This manual discusses the operation of the Controlatron Test Suite Software and a brief discussion of state machine theory, as state machine is the functional basis of the software.

Automation of inspection methods for eddy current testing of steam generator tubes

International Nuclear Information System (INIS)

Meurgey, P.; Baumaire, A.

1990-01-01

Inspection of all the tubes of a steam generator when the reactor is stopped is required for some of these exchangers affected by stress corrosion cracking. Characterization of each crack, in each tube is made possible by the development of software for processing the signals from an eddy current probe. The ESTELLE software allows a rapid increase of tested tubes, more than 80,000 in 1989 [fr

Evaluation of tube rupture simulation test (TRUST-1) for FBR steam generators

Energy Technology Data Exchange (ETDEWEB)

Hayashida, Yoshihiko; Hamada, Hirotsugu [Power Reactor and Nuclear Fuel Development Corp., Oarai, Ibaraki (Japan). Oarai Engineering Center

1996-06-01

The intermediate water leak in an FBR Steam Generator (SG) causes a high temperature and corrosive sodium-water reaction jet. In such cases, it is necessary to evaluate the wastage and overheating rupture behavior of heat transfer tubes. Especially, in the large SG that aims at high temperature of sodium and high temperature/pressure of water, the establishment of the rational evaluation method is important. In this paper, as a basic experiment to make clear the phenomenon of overheating rupture, tests and analysis of Tube Rupture Simulation Test-1 (TRUST-1) were conducted. TRUST-1 simulates the overheating rupture of the tube made of Mod.9Cr-1Mo steel by nitrogen gas pressurization and quick induction heating. The result of TRUST-1 are as follows: (1) The breaking strength predicted by the internal pressure is larger than the tensile strength of the tube material. (2) The margin of the breaking strength from the tensile strength of the tube material has a tendency of decreasing with the heating rate, especially in the lower temperature region. (3) Using an theoretical formula that is deduced from the steady creep model and appropriate experimental coefficients that are determined by the test data, the breaking strength can be reasonably evaluated. (author)

The EL-4 reactor. Changing of a pressure tube on a test loop

International Nuclear Information System (INIS)

Foulquier, H.; Clara, P.

1964-01-01

Right from the beginning of the EL-4 project, the research convected with the overall design of the reactor was guided by the various technical specifications resulting from a justifiable concern about the reliability. The external and internal tubes of each layer situated in the reactor block had in particular to be interchangeable. The research alone into the dismantling of the external tube, i.e in fact the pressure tube, justified a certain number of full-scale tests on a model. The tests carried out under relevant conditions on a non-irradiated structure made it possible to define a complete ranger of of positioning and un-positioning sequences at a distance for such a pressure tube. (authors) [fr

Exact BPS bound for noncommutative baby Skyrmions

International Nuclear Information System (INIS)

Domrin, Andrei; Lechtenfeld, Olaf; Linares, Román; Maceda, Marco

2013-01-01

The noncommutative baby Skyrme model is a Moyal deformation of the two-dimensional sigma model plus a Skyrme term, with a group-valued or Grassmannian target. Exact abelian solitonic solutions have been identified analytically in this model, with a singular commutative limit. Inside any given Grassmannian, we establish a BPS bound for the energy functional, which is saturated by these baby Skyrmions. This asserts their stability for unit charge, as we also test in second-order perturbation theory

Risks of Using Bedside Tests to Verify Nasogastric Tube Position in Adult Patients

Directory of Open Access Journals (Sweden)

Melody Ni

2014-12-01

Full Text Available Nasogastric (NG tubes are commonly used for enteral feeding. Complications of feeding tube misplacement include malnutrition, pulmonary aspiration, and even death. We built a Bayesian network (BN to analyse the risks associated with available bedside tests to verify tube position. Evidence on test validity (sensitivity and specificity was retrieved from a systematic review. Likelihood ratios were used to select the best tests for detecting tubes misplaced in the lung or oesophagus. Five bedside tests were analysed including magnetic guidance, aspirate pH, auscultation, aspirate appearance, and capnography/colourimetry. Among these, auscultation and appearance are non-diagnostic towards lung or oesophagus placements. Capnography/ colourimetry can confirm but cannot rule out lung placement. Magnetic guidance can rule out both lung and oesophageal placement. However, as a relatively new technology, further validation studies are needed. The pH test with a cut-off at 5.5 or lower can rule out lung intubation. Lowering the cut-off to 4 not only minimises oesophageal intubation but also provides extra safety as the sensitivity of pH measurement is reduced by feeding, antacid medication, or the use of less accurate pH paper. BN is an effective tool for representing and analysing multi-layered uncertainties in test validity and reliability for the verification of NG tube position. Aspirate pH with a cut-off of 4 is the safest bedside method to minimise lung and oesophageal misplacement.

Atmospheres in a Test Tube

Science.gov (United States)

Claudi, R.; Erculiani, M. S.; Giro, E.; D'Alessandro, M.; Galletta, G.

2013-09-01

The "Atmosphere in a Test Tube" project is a laboratory experiment that will be able to reproduce condition of extreme environments by means of a simulator. These conditions span from those existing inside some parts of the human body to combinations of temperatures, pressures, irradiation and atmospheric gases present on other planets. In this latter case the experiments to be performed will be useful as preliminary tests for both simulation of atmosphere of exoplanets and Solar System planets and Astrobiology experiments that should be performed by planetary landers or by instruments to be launched in the next years. In particular at INAF Astronomical Observatory of Padova Laboratory we are approaching the characterization of extrasolar planet atmospheres taking advantage by innovative laboratory experiments with a particular focus on low mass Neptunes and Super earths and low mass M dwarfs primaries.

Failure analysis of burst tested fuel tube samples

International Nuclear Information System (INIS)

Padmaprabu, C.; Ramana Rao, S.V.; Srivatsava, R.K.

2005-01-01

The Total Circumferential Elongation (TCE) is an important parameter for evaluation of ductility of the Zircaloy-4 fuel tubes for the PHWR reactors. The TCE values of the fuel tubes were obtained using the burst testing technique. In some lots there is a variation in the values of the TCE. To investigate the reasons for such a large variation in the TCE, samples were selected at appropriate intervals and sectioned at the fractured portion. The surface morphology of the fractured surfaces was examined under Scanning Electron Microscope (SEM) equipped with Energy Dispersive Spectrometer (EDS). The morphologies show segregation of elements at specific locations. Energy dispersive spectra was obtained from those segregated particles. According to the magnitude of TCE value the samples were classified into low, intermediate and high ductility. Low ductility samples were found to contain large amount of segregations along the thickness direction of the tube. This forms a brittle region and a path for the easy crack growth along thickness direction. In the case of intermediate samples the segregation occurred in fewer locations compared to low ductile samples and also confined to the circumferential direction of the outside surface of the tube. Due to this, probability of crack formation at the surface of the tube could be high. But crack growth would be slower in the ductile matrix along the thickness direction resulting in the enhancement of TCE value compared to the low ductile sample. In the high ductile samples, the segregations were very scarce and found to be isolated and embedded in the ductile matrix. The mode of failure in these types of samples was found to be purely ductile. Cracks were found to originate solely from the micro voids in the material. As the probability of crack formation and its propagation is low, very high TCE values were observed in these samples. Microstructural observations of fractured surfaces and EDAX analysis was able to identify the

Healthy Smile for Your Baby

Science.gov (United States)

... your baby is 1 year old before feeding him cow’s milk. m Hold your baby while feeding him breast milk or formula in a bottle. m ... your baby is 1 year old before giving him juice. m When your baby is around 4 ...

Preliminary research on eddy current bobbin quantitative test for heat exchange tube in nuclear power plant

Science.gov (United States)

Qi, Pan; Shao, Wenbin; Liao, Shusheng

2016-02-01

For quantitative defects detection research on heat transfer tube in nuclear power plants (NPP), two parts of work are carried out based on the crack as the main research objects. (1) Production optimization of calibration tube. Firstly, ASME, RSEM and homemade crack calibration tubes are applied to quantitatively analyze the defects depth on other designed crack test tubes, and then the judgment with quantitative results under crack calibration tube with more accuracy is given. Base on that, weight analysis of influence factors for crack depth quantitative test such as crack orientation, length, volume and so on can be undertaken, which will optimize manufacture technology of calibration tubes. (2) Quantitative optimization of crack depth. Neural network model with multi-calibration curve adopted to optimize natural crack test depth generated in in-service tubes shows preliminary ability to improve quantitative accuracy.

7 CFR 319.56-48 - Conditions governing the entry of baby squash and baby courgettes from Zambia.

Science.gov (United States)

2010-01-01

... 7 Agriculture 5 2010-01-01 2010-01-01 false Conditions governing the entry of baby squash and baby... Fruits and Vegetables § 319.56-48 Conditions governing the entry of baby squash and baby courgettes from Zambia. Baby squash (Curcurbita maxima Duchesne) and baby courgettes (C. pepo. L.) measuring 10 to 25...

Geometric Relations for CYLEX Test Tube-Wall Motion

Science.gov (United States)

Hill, Larry

2015-06-01

The CYLinder EXpansion (CYLEX) test is a (precision, instrumented, high-purity annealed copper) pipe bomb. Its essential measured quantities are detonation speed and tube-wall motion. Its main purpose is to calibrate detonation product equations of state (EOS) by measuring how product fluid pushes metal. In its full complexity, CYLEX is an integral test, for which EOS calibration requires the entire system to be computationally modeled and compared to salient data. Stripped to its essence, CYLEX is a non-integral test for which one may perform the inverse problem, to infer the EOS directly from data. CYLEX analysis can be simplified by the fact that the test constituents achieve a steady traveling wave structure; this allows derivation of several useful geometric relationships regarding tube wall motion. The first such treatment was by G.I. Taylor. Although his analysis was limited to small wall deflection angles, he asserted that the results remain valid for arbitrary ones. I confirm this attribute and present additional useful relationships. In the past decade, CYLEX wall-motion instrumentation has migrated almost entirely from streak camera to PDV, yet discrepancies remain between the two methods. I further present geometric relationships that shed light on this issue. Work supported by the U.S. DOE.

JSW's baby cyclotron

International Nuclear Information System (INIS)

Toda, Y.; Kaneda, Y.; Satoh, Y.; Suzukawa, I.; Yamada, T.

1983-01-01

Designed by The Japan Steel Works, Ltd., specially for installation in a hospital's medical department and nuclear research laboratory, '' JSW BABY CYCLOTRON '' has been developed to produce short-lived radioisotopes such as 11C, 13N, 15O and 18F. JSW's Baby Cyclotron has some design features. 1) Fixed energy and four sector azimuthally varying field. 2) Compact figure desired for hospital's nuclear medical department 3) A bitter type magnet yoke shielding activity 4) Simple control and operation 5) Easy maintenance without skilled personnel. Type BC105 (P:10MeV, d:5MeV), BC107 (P:10MeV, d:7MeV), BC168 (P:16MeV, d:8MeV) and BC1710 (P:17MeV, d:10MeV) are available according to required amount of radioisotopes. In our radioisotope production test, yield and purity of 11C, 13N, 15O and 18F are usable to clinical diagnosis

CDC Screening Recommendation for Baby Boomers and Hepatitis C Virus Testing in the US Military Health System.

Science.gov (United States)

Manjelievskaia, Janna; Brown, Derek; Shriver, Craig D; Zhu, Kangmin

Chronic hepatitis C virus (HCV) is the most common blood-borne infection in the United States, with an estimated 2.7 to 3.9 million cases as of 2014. In August 2012, the Centers for Disease Control and Prevention (CDC) recommended 1-time HCV testing of all baby boomers. The objectives of this study were to (1) determine the proportion of people screened for HCV in the US Department of Defense Military Health System before and after the CDC screening recommendation for baby boomers and (2) assess whether certain patient or system factors were associated with screening for HCV before and after August 2012. We used a dataset containing 5% of beneficiaries randomly selected from the Military Health System Data Repository medical claims database for the period July 2011 through September 2013. Of 108 223 people eligible for HCV screening during the first period (July 2011 through July 2012), 1812 (1.7%) were screened. Of 109 768 people eligible during the second period (September 2012 through September 2013), 2599 (2.4%) were screened. HCV screening receipt was related to benefit type (Prime before August 2012: adjusted odds ratio [aOR] = 2.16; 95% confidence interval [CI], 1.89-2.46; Prime after August 2012: aOR = 1.93; 95% CI, 1.73-2.16) and care source (direct care before August 2012: aOR = 1.80; 95% CI, 1.57-2.07; direct care after August 2012: aOR = 2.45; 95% CI, 2.18-2.75); male sex (aOR = 1.17; 95% CI, 1.06-1.29) and black race (aOR = 1.20; 95% CI, 1.05-1.37) were associated with HCV testing only before August 2012. Interventions should be implemented to increase awareness and knowledge of the current national HCV testing recommendation among baby boomers to seek out testing and health care providers to perform screening.

Design and test of the Stirling-type pulse tube cryocooler

Science.gov (United States)

Hong, Yong-Ju; Ko, Junseok; Kim, Hyo-Bong; Yeom, Han-Kil; In, Sehwan; Park, Seong-Je

2017-12-01

Stirling type pulse tube cryocoolers are very attractive for cooling of diverse application because it has it has several inherent advantages such as no moving part in the cold end, low manufacturing cost and long operation life. To develop the Stirling-type pulse tube cryocooler, we need to design a linear compressor to drive the pulse tube cryocooler. A moving magnet type linear motor of dual piston configuration is designed and fabricated, and this compressor could be operated with the electric power of 100 W and the frequency up to 60 Hz. A single stage coaxial type pulse tube cold finger aiming at over 1.5 W at 80K is built and tested with the linear compressor. Experimental investigations have been conducted to evaluate their performance characteristics with respect to several parameters such as the phase shifter, the charging pressure and the operating frequency of the linear compressor.

Numerical investigation of tube hyroforming of TWT using Corner Fill Test

Science.gov (United States)

Zribi, Temim; Khalfallah, Ali

2018-05-01

Tube hydroforming presents a very good alternative to conventional forming processes for obtaining good quality mechanical parts used in several industrial fields, such as the automotive and aerospace sectors. Research in the field of tube hydroforming is aimed at improving the formability, stiffness and weight reduction of manufactured parts using this process. In recent years, a new method of hydroforming appears; it consists of deforming parts made from welded tubes and having different thicknesses. This technique which contributes to the weight reduction of the hydroformed tubes is a good alternative to the conventional tube hydroforming. This technique makes it possible to build rigid and light structures with a reduced cost. However, it is possible to improve the weight reduction by using dissimilar tailor welded tubes (TWT). This paper is a first attempt to analyze by numerical simulation the behavior of TWT hydroformed in square cross section dies, commonly called (Corner Fill Test). Considered tubes are composed of two materials assembled by butt welding. The present analysis will focus on the effect of loading paths on the formability of the structure by determining the change in thickness in several sections of the part. A comparison between the results obtained by hydroforming the butt joint of tubes made of dissimilar materials and those obtained using single-material tube is achieved. Numerical calculations show that the bi-material welded tube has better thinning resistance and a more even thickness distribution in the circumferential directions when compared to the single-material tube.

Fluid elastic instability tests on an array of tubes preferentially flexible in the flow direction

International Nuclear Information System (INIS)

Mureithi, N.W.; Zhang, C.; Pettigrew, M.J.

2004-01-01

The present work is motivated by the observation that, in the presence of flat bar supports (AVBs), U-tubes in steam generators and heat exchangers are not positively restrained in the in-plane direction. The stability behavior of a rotated triangular array is investigated in detail in the work presented here. Tubes within the array are flexible only in the flow direction. Tests are conducted with a fully flexible array, a single flexible tube, and a finite number of flexible tubes at several locations within the otherwise rigid array. In all cases tube flexibility is purely in the flow direction. The fully flexible array is shown to undergo fluid-elastic instability. Despite the unidirectional flexibility constraint, the critical instability velocity is of the same order of magnitude when compared with previous tests on an unconstrained fully flexible array. A single flexible tube, on the other hand, is found to be stable. Results of tests on partially flexible array configurations are also presented. (authors)

Noncommutative baby Skyrmions

International Nuclear Information System (INIS)

Ioannidou, Theodora; Lechtenfeld, Olaf

2009-01-01

We subject the baby Skyrme model to a Moyal deformation, for unitary or Grassmannian target spaces and without a potential term. In the Abelian case, the radial BPS configurations of the ordinary noncommutative sigma model also solve the baby Skyrme equation of motion. This gives a class of exact analytic noncommutative baby Skyrmions, which have a singular commutative limit but are stable against scaling due to the noncommutativity. We compute their energies, investigate their stability and determine the asymptotic two-Skyrmion interaction.

Baby M: babies (and justice) for sale.

Science.gov (United States)

Annas, G J

1987-06-01

A professor of health law criticizes the decisions of New Jersey Superior Court Judge Harvey R. Sorkow which culminated in his awarding permanent custody of Baby M to her biological father, William Stern. Annas quotes from the In re Baby M decision and from the contract between Stern and his wife and surrogate mother Mary Beth Whitehead to support his contention that Sorkow "rendered a sermon filled with contradictions, double-standards, inapt analogies, and unsupported conclusions." He argues that legally Mrs. Whitehead could not have prospectively waived her right to rear a child she bore, that Sorkow was biased in favor of the "upper-middle-class Sterns," and that consideration should be given to returning Baby M to Mrs. Whitehead. He urges state legislatures to outlaw the sale of children, to affirm the legal status of the gestational mother, and to forbid a surrogate's relinquishment of parental rights until after her child's birth.

A novel test tube method of screening for hemoglobin E.

Science.gov (United States)

Tatu, T; Kasinrerk, W

2012-02-01

Hemoglobin (Hb) E is a β-structural variant common worldwide. This Hb disorder can form a compound heterozygous state with the β-thalassemia gene, leading to life-threatening hereditary hemolytic anemia, HbE/β-thalassemia. Screening of HbE has proven to be a challenging practice in prevention and control of the HbE/β-thalassemia. A novel test tube method for HbE screening using diethyl aminoethyl (DEAE)-cellulose resin was described. With the developed system, HbE/A(2) did not bind to the resin and remained dissolved in the supernatant, whereas other Hbs completely bound to the resin. The red color of the supernatant observed in the test tube indicated the presence of HbE. Colorless or markedly pale color of the supernatant indicates the absence of HbE. Accuracy and efficiency of the established method in detecting HbE was comparable with the standard cellulose acetate electrophoresis method. The developed method is cheap and simple with no requirement of sophisticated equipment. The reagent could be stored at 4 °C for up to 5 months. Hemolysate samples aged up to 5 months were still suitable for this test. The described novel test tube method could be an alternative method of mass population screening for HbE, particularly in small health care facilities. © 2011 Blackwell Publishing Ltd.

Respon Imun Anak Babi Pasca Vaksinasi Hog Cholera

Directory of Open Access Journals (Sweden)

I Made Jayanata

2016-10-01

Full Text Available Penelitian ini bertujuan untuk mengetahui pengaruh antibodi maternal terhadap titer antibodi anak babi yang di vaksin hog cholera umur 7 hari. Penelitian menggunakan tujuh sampel babi dari induk yang divaksin secara teratur yang diberikan perlakuan vaksinasi pada umur 7 hari. Pengambilan sampel serum dilakukan pravaksinasi (7 hari, dan satu minggu serta dua minggu pasca vaksinasi. Untuk menentukan titer antibodi virus Hog cholera pada sampel anak babi dilakukan uji ELISA. Data yang diperoleh kemudian dianalisis mengunakan paired sampel T test antara titer antibodi hog cholera. Hasil paired sample T test menunjukkan terjadinya penurunan titer antibodi maternal yang nyata (p<0,05 pada pra vaksinasi ( umur 7 hari dengan satu minggu pasca vaksinasi dan sangat nyata (p<0,01 dengan hari dua minggu pasca vaksinasi. Dari hasil penelitian ini dapat disimpulkan bahwa antibodi maternal yang tinggi akan mengakibatkan penurunan pada titer antibodi pasca vaksinasi. Perlu dilakukan penelitian lebih lanjut untuk mengetahui waktu vaksinasi yang efektif

NASA Lewis Stirling SPRE testing and analysis with reduced number of cooler tubes

International Nuclear Information System (INIS)

Wong, W.A.; Cairelli, J.E.; Swec, D.M.; Doeberling, T.J.; Lakatos, T.F.; Madi, F.J.

1994-01-01

Free-piston Stirling power converters are a candidate for high capacity space power applications. The Space Power Research Engine (SPRE), a free-piston Stirling engine coupled with a linear alternator, is being tested at the NASA Lewis Research Center in support of the Civil Space Technology Initiative. The SPRE is used as a test bed for evaluating converter modifications which have the potential to improve converter performance and for validating computer code predictions. Reducing the number of cooler tubes on the SPRE has been identified as a modification with the potential to significantly improve power and efficiency. This paper describes experimental tests designed to investigate the effects of reducing the number of cooler tubes on converter power, efficiency and dynamics. Presented are test results from the converter operating with a reduced number of cooler tubes and comparisons between this data and both baseline test data and computer code predictions

Testing of a 7-tube palladium membrane reactor for potential use in TEP

International Nuclear Information System (INIS)

Carlson, Bryan J.; Trujillo, Stephen; Willms, R. Scott

2010-01-01

A Palladium Membrane Reactor (PMR) consists of a palladium/silver membrane permeator filled with catalyst (catalyst may be inside or outside the membrane tubes). The PMR is designed to recover tritium from the methane, water, and other impurities present in fusion reactor effluent. A key feature of a PMR is that the total hydrogen isotope content of a stream is significantly reduced as (1) methane-steam reforming and/or water-gas shift reactions proceed on the catalyst bed and (2) hydrogen isotopes are removed via permeation through the membrane. With a PMR design matched to processing requirements, nearly complete hydrogen isotope removals can be achieved. A 3-tube PMR study was recently completed. From the results presented in this study, it was possible to conclude that a PMR is appropriate for TEP, perforated metal tube protectors function well, platinum on aluminum (PtA) catalyst performs the best, conditioning with air is probably required to properly condition the Pd/Ag tubes, and that CO/CO 2 ratios maybe an indicator of coking. The 3-tube PMR had a permeator membrane area of 0.0247 m 2 and a catalyst volume to membrane area ratio of 4.63 cc/cm 2 (with the catalyst on the outside of the membrane tubes and the catalyst only covering the membrane tube length). A PMR for TEP will require a larger membrane area (perhaps 0.35 m 2 ). With this in mind, an intermediate sized PMR was constructed. This PMR has 7 permeator tubes and a total membrane area of 0.0851 m 2 . The catalyst volume to membrane area ratio for the 7-tube PMR was 5.18 cc/cm 2 . The total membrane area of the 7-tube PMR (0.0851 m 2 ) is 3.45 times larger than total membrane area of the 3-tube PMR (0.0247 m 2 ). The following objectives were identified for the 7-tube PMR tests: (1) Refine test measurements, especially humidity and flow; (2) Refine maintenance procedures for Pd/Ag tube conditioning; (3) Evaluate baseline PMR operating conditions; (4) Determine PMR scaling method; (5) Evaluate PMR

Experiment data report for semiscale Mod-1 test S-28-2 (steam generator tube rupture test)

International Nuclear Information System (INIS)

Patton, M.L.; Sackett, K.E.

1977-10-01

Recorded test data are presented for Test S-28-2 of the Semiscale Mod-1 steam generator tube rupture test series. These tests are among several Semiscale Mod-1 experiments conducted to investigate the thermal and hydraulic phenomena accompanying a hypothesized loss-of-coolant accident in a pressurized water reactor (PWR) system. Test S-28-2 was conducted from initial conditions of 15 936 kPa and 558 K to investigate the response of the Semiscale Mod-1 system to a depressurization and reflood transient following a simulated double-ended offset shear of the broken loop cold leg piping. During the test, cooling water was injected into the cold leg of the intact and broken loops to simulate emergency core coolant injection in a PWR. For Test S-28-2, accumulator injection into the intact loop hot leg was provided to simulate simulate the rupture of six steam generator tubes

The Effects of Baby Sign Training on Child Development

Science.gov (United States)

Mueller, Vannesa; Sepulveda, Amanda; Rodriguez, Sarai

2014-01-01

Although Baby Sign is gaining in popularity, there is a scarcity of research supporting its use. The research that has been conducted is conflicting. In the current study, nine families with children ranging in age from six months to two years and five months participated in a baby sign workshop. A pre--post-test design was used to assess the…

Application of palatal RB obturator in babies with isolated palatal cleft

Directory of Open Access Journals (Sweden)

Radojičić Julija

2009-01-01

Full Text Available Background. Isolated cleft of secondary palate has a specific clinical picture due to a wide communication between the mouth and nose cavity. As a consequence of that, babies born with this malformation are often subject to infections of the upper bronchial tubes, middle ear, speech disorders, and certainly the most difficult existential problem they face at the very beginning of their lives, the impossibility of suckling (breast feeding. Such babies have to be fed with gastric probe. The difficulties in their nutrition have often been described in literature, yet a singular attitude toward early orthodontic therapy has not been adopted still. The aim of the paper was to describe a design and application of obturator immediately after the birth of a baby with isolated palatal cleft, and the role in feeding. Case report. We presented a female neonate, born on 27th December 2007, with a wide fissure in the shape of the letter U over the entire secondary palate. The baby was referred to the Stomatology Clinic due to nutrition impossibility. To avoid feeding with gastric probe, the formation of RB obturator was performed (artificial palate. Hereby, the procedure of obturator making with an explanation of its function is presented. Conclusion. The application of RB obturator and the necessary education of parents have a major role in shortening the time of breast feeding and increasing the amount of food intake and, thus, for the normal growth and development of newborn infants with isolated palate cleft.

Progranulin haploinsufficiency causes biphasic social dominance abnormalities in the tube test.

Science.gov (United States)

Arrant, A E; Filiano, A J; Warmus, B A; Hall, A M; Roberson, E D

2016-07-01

Loss-of-function mutations in progranulin (GRN) are a major autosomal dominant cause of frontotemporal dementia (FTD), a neurodegenerative disorder in which social behavior is disrupted. Progranulin-insufficient mice, both Grn(+/-) and Grn(-/-) , are used as models of FTD due to GRN mutations, with Grn(+/-) mice mimicking the progranulin haploinsufficiency of FTD patients with GRN mutations. Grn(+/-) mice have increased social dominance in the tube test at 6 months of age, although this phenotype has not been reported in Grn(-/-) mice. In this study, we investigated how the tube test phenotype of progranulin-insufficient mice changes with age, determined its robustness under several testing conditions, and explored the associated cellular mechanisms. We observed biphasic social dominance abnormalities in Grn(+/-) mice: at 6-8 months, Grn(+/-) mice were more dominant than wild-type littermates, while after 9 months of age, Grn(+/-) mice were less dominant. In contrast, Grn(-/-) mice did not exhibit abnormal social dominance, suggesting that progranulin haploinsufficiency has distinct effects from complete progranulin deficiency. The biphasic tube test phenotype of Grn(+/-) mice was associated with abnormal cellular signaling and neuronal morphology in the amygdala and prefrontal cortex. At 6-9 months, Grn(+/-) mice exhibited increased mTORC2/Akt signaling in the amygdala and enhanced dendritic arbors in the basomedial amygdala, and at 9-16 months Grn(+/-) mice exhibited diminished basal dendritic arbors in the prelimbic cortex. These data show a progressive change in tube test dominance in Grn(+/-) mice and highlight potential underlying mechanisms by which progranulin insufficiency may disrupt social behavior. © 2016 John Wiley & Sons Ltd and International Behavioural and Neural Genetics Society.

Collodion baby

Directory of Open Access Journals (Sweden)

Dhaded S

1992-01-01

Full Text Available Collodion baby is a rare congenital disorder characterized by parchment like taught membrane covering the whole body. Other findings in our case include ectropion, eversion of lips, and flattening of nose and ears. Skin biopsy showed features consistant with the diagnosis of collodion baby. The child was treated with supportive measures like antibiotics, intravenous fluids, humidification, and application of emollients.

Feeding Your Baby

Medline Plus

Full Text Available ... Global Map Premature Birth Report Cards Careers Archives Health Topics Pregnancy Before or between pregnancies Nutrition, weight & ... Caring for your baby Feeding your baby Family health & safety Complications & Loss Pregnancy complications Preterm labor & premature ...

Feeding Your Baby

Medline Plus

Full Text Available ... and your partner to bond with her. Breast milk is the best food for your baby during ... life. Learn how to breastfeed and why breast milk is so good for babies. You and your ...

Feeding Your Baby

Medline Plus

Full Text Available ... a valid e-mail address. Your information: Your recipient's information: Your personal message: Thank you! Your e- ... good for babies. You and your baby may need time and practice to get comfortable breastfeeding, but ...

Feeding Your Baby

Medline Plus

Full Text Available ... between pregnancies Nutrition, weight & fitness Prenatal care Is it safe? Labor & birth Postpartum care Baby Caring for ... between pregnancies Nutrition, weight & fitness Prenatal care Is it safe? Labor & birth Postpartum care Baby Caring for ...

Feeding Your Baby

Medline Plus

Full Text Available ... The Prematurity Campaign About us Annual report Our work Community impact Global programs Research Need help? Frequently ... Nutrition, weight & fitness Prenatal care Is it safe? Labor & birth Postpartum care Baby Caring for your baby ...

Improvement of the vibration of the test fuel(Type-B) with a guide tube under operational condition

Energy Technology Data Exchange (ETDEWEB)

Sohn, Dong Seung; Yim, Jeong Sik; Lim, I. C. [Korea Atomic Energy Research Institute, Taejon (Korea)

1999-04-01

The Type-B test fuel for the Hanaro has a flexible guide tube on top of the fuel to lead and guide the instrumentation wires. Depending on the flow condition in the reactor, the fuel is susceptible to vibration. During the test operation of the fuel, a fairly large amplitude vibration was observed and the possibility of flow tube contact with adjacent flow tubes, due to the excessive vibration of the fuel, and consequent wear or defect of the flow tubes were raised. Thus, to know the vibration characteristics as well as whether the flow tube contact each other, analyses of the Type-B fuel the dummy fuel were performed by BEVIRA and ANSYS. Besides the analyses, vibration tests using the dummy fuel in air and with Type-B fuel in the core at zero power under operational flow condition were executed. The results from the analyses were compared with those from tests to validate the analyses. From the deflection test of the dummy fuel in air to get the maximum displacement of the flow tube at the top, the flow tube were found to contact each other. For the prevention of the contact of the flow tubes caused by the excessive vibration of the guide tube, an additional support to the guide tube was proposed. With the additional support, analysis and in core vibration test under operational flow condition were conducted and there found to be no excessive vibration any more. 6 refs., 16 figs., 6 tabs. (Author)

Feeding Your Baby

Medline Plus

Full Text Available ... Pregnancy Before or between pregnancies Nutrition, weight & fitness Prenatal care Is it safe? Labor & birth Postpartum care Baby ... Pregnancy Before or between pregnancies Nutrition, weight & fitness Prenatal care Is it safe? Labor & birth Postpartum care Baby ...

Feeding Your Baby

Medline Plus

Full Text Available ... for your baby Feeding your baby Family health & safety Complications & Loss Pregnancy complications Preterm labor & premature birth The newborn intensive care unit (NICU) Birth defects & other health conditions Loss & grief Tools & Resources Frequently asked health questions ...

Experiment data report for Semiscale Mod-1 test S-28-3 (steam generator tube rupture test)

International Nuclear Information System (INIS)

Gillins, R.L.; Sackett, K.E.

1977-10-01

Recorded test data are presented for Test S-28-3 of the Semiscale Mod-1 steam generator tube rupture test series. These tests are among several Semiscale Mod-1 experiments conducted to investigate the thermal and hydraulic phenomena accompanying a hypothesized loss-of-coolant accident in a pressurized water reactor (PWR) system. Test S-28-3 was conducted from initial conditions of 15621 kPa and 555 K to investigate the response of the Semiscale Mod-1 system to a depressurization and reflood transient following a simulated double-ended offset shear of the broken loop cold leg piping. During the test, cooling water was injected into the cold leg of the intact and broken loops to simulate emergency core coolant injection in a PWR. Twelve steam generator tube ruptures were simulated by a controlled injection from a heated accumulator into the intact loop hot leg

Experiment data report for semiscale Mod-1 test S-28-4 (steam generator tube rupture test)

International Nuclear Information System (INIS)

Esparza, V.; Sackett, K.E.

1977-10-01

Recorded test data are presented for Test S-28-4 of the Semiscale Mod-1 steam generator tube rupture test series. These tests are among several Semiscale Mod-1 experiments conducted to investigate the thermal and hydraulic phenomena accompanying a hypothesized loss-of-coolant accident in a pressurized water reactor (PWR) system. Test S-28-4 was conducted from initial conditions of 15 646 kPa and 557 K to investigate the response of the Semiscale Mod-1 system to a depressurization and reflood transient following a simulated double-ended offset shear of the broken loop cold leg piping. During the test, cooling water was injected into the cold leg of the intact and broken loops to simulate emergency core coolant injection in a PWR. Thirty steam generator tube ruptures were simulated by a controlled injection from a heated accumulator into the intact loop hot leg

Method and apparatus for testing closed-end tubes in heat exchangers of nuclear reactors and the like

International Nuclear Information System (INIS)

Seyd, G.; Bergbauer, A.; Paulsen, U.

1975-01-01

A description is given of a test stopper which is insertable into a tube closed at one end for testing the tightness of the tube with a fluid under pressure, the tube being in a heat exchanger of a nuclear reactor or the like. The test stopper includes a tubular outer jacket that is expandable outwardly to tightly seat the stopper in the tube. The stopper also has front and back end-face members joined to the ends of the outer jacket to define a closed space within the jacket. With the stopper inserted into the tube, the front end-face member and the closed end portion of the tube define a closed inner region of the tube. An inner tubular member, disposed within the outer jacket, partitions the closed space within the jacket into an annular outer chamber and a cylindrical inner chamber. A pressure-fluid supply selectively supplies fluid to the chambers. The outer jacket expands in response to fluid admitted to the annular chamber and the front end-face member has a through bore to admit fluid under pressure to the inner region of the tube. A method of testing of such a tube with a fluid under pressure includes inserting the test stopper into the tube and then expanding the outer jacket of the stopper to seat the stopper firmly in the tube. A fluid under pressure is directed through the stopper and into the closed region defined by the front end-face member of the stopper and the closed end portion of the tube. The pressure of the fluid introduced into this closed region is monitored for detecting a leak in the closed-end tube

Baby Brain Map

Science.gov (United States)

... a Member Home Resources & Services Professional Resource Baby Brain Map Mar 17, 2016 The Brain Map was adapted in 2006 by ZERO TO ... supports Adobe Flash Player. To view the Baby Brain Map, please visit this page on a browser ...

Smokefree After Baby

Science.gov (United States)

Many women quit smoking when they become pregnant. However, about 40 percent start smoking again 6 months after they have their baby. Quitting smoking has benefits for you and your baby that last longer than the 9 months of your pregnancy.

Out-of pile mechanical test: simulating reactivity initiated accident (RIA) of zircaloy-4 cladding tube

Energy Technology Data Exchange (ETDEWEB)

Lee, Myung Ho; Kim, Jun Hwan; Choi, Byoung Kwon; Jeong, Young Hwan [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

2004-07-01

The ejection or drop of a control rod in a reactivity initiated accident (RIA) causes a sudden increase in reactor power and in turn deposits a large amount of energy into the fuel. In a RIA, cladding tubes bear thermal expansion due to sudden reactivity and may fail from the resulting mechanical damage. Thus, RIA can be one of the safety margin reducers because the oxide on the tubes makes their thickness to support the load less as well as hydrides from the corrosion reduce the ductility of the tubes. In a RIA, the peak of reactor power from reactivity change is about 0.1m second and the temperature of the cladding tubes increases up to 1000 .deg. C in several seconds. Although it is hard to fully simulate the situation, several attempts to measure the change of mechanical properties under a RIA situation has done using a reduction coil, ring tension tests with high speed. This research was done to see the effect of oxide on the change of circumferential strength and ductility of Zircaloy-4 tubes in a RIA. The ring stretch tensile tests were performed with the strain rate of 1/sec and 0.01/s to simulate a transient of the cladding tube under a RIA. Since the test results of the ring tensile test are very sensitive to the lubricant, the tests were also carried out to select a suitable lubricant before the test of oxided specimens.

Scramjet test flow reconstruction for a large-scale expansion tube, Part 2: axisymmetric CFD analysis

Science.gov (United States)

Gildfind, D. E.; Jacobs, P. A.; Morgan, R. G.; Chan, W. Y. K.; Gollan, R. J.

2017-11-01

This paper presents the second part of a study aiming to accurately characterise a Mach 10 scramjet test flow generated using a large free-piston-driven expansion tube. Part 1 described the experimental set-up, the quasi-one-dimensional simulation of the full facility, and the hybrid analysis technique used to compute the nozzle exit test flow properties. The second stage of the hybrid analysis applies the computed 1-D shock tube flow history as an inflow to a high-fidelity two-dimensional-axisymmetric analysis of the acceleration tube. The acceleration tube exit flow history is then applied as an inflow to a further refined axisymmetric nozzle model, providing the final nozzle exit test flow properties and thereby completing the analysis. This paper presents the results of the axisymmetric analyses. These simulations are shown to closely reproduce experimentally measured shock speeds and acceleration tube static pressure histories, as well as nozzle centreline static and impact pressure histories. The hybrid scheme less successfully predicts the diameter of the core test flow; however, this property is readily measured through experimental pitot surveys. In combination, the full test flow history can be accurately determined.

Deteksi Antibodi terhadap Cysticercus Cellulosae pada Babi Lokal yang Dipotong di Tempat Pemotongan Babi Panjer, Denpasar

Directory of Open Access Journals (Sweden)

Ida Bagus Ngurah Swacita

2016-03-01

Full Text Available Sistiserkosis merupakan penyakit yang bersifat zoonosis yang disebabkan oleh larva cacing pita Taenia solium yang disebut Cysticercus cellulosae. Di Indonesia terdapat tiga provinsi yang berstatus endemik penyakit sistiserkosis, salah satunya adalah provinsi Bali. Penelitian ini bertujuan untuk mendeteksi antibodi terhadap C. cellulosae pada babi lokal yang dipotong di tempat pemotongan babi Panjer, Denpasar. Sampel penelitian adalah 270 sampel serum babi lokal yang dipotong di tempat pemotongan babi Panjer, Denpasar Selatan. Babi lokal ini berasal dari Nusa Penida, Karangasem dan Negara. Sampel serum diuji dengan metode ELISA (Enzyme Linked Immunosorbent Assay indirect. Hasil penelitian menunjukkan bahwa antibodi C. cellulosae terdeteksi pada 33 sampel. Disimpulkan bahwa terdeteksi antibodi C. cellulosae pada 33 sampel dari 270 sampel serum babi lokal yang dipotong di tempat pemotongan babi Panjer, Denpasar.

Shaken Baby Syndrome

Science.gov (United States)

... baby syndrome. Information from the National Library of Medicine’s MedlinePlus Child Abuse × What research is being done? The National ... baby syndrome. Information from the National Library of Medicine’s MedlinePlus Child Abuse See More About Research The National Institute ...

Tests and analysis on steam generator tube failure propagation

International Nuclear Information System (INIS)

Tanabe, Hiromi

1990-01-01

The understanding of leak enlargement and failure propagation behavior is essential to select a design basis leak (DBL) of LMFBR steam generators. Therefore, various series of experiments, such as self-enlargement tests, target wastage tests, failure propagation tests were conducted in a wide range of leak using test facilities of SWAT at PNC/OEC. Especially, in the large leak tests, potential of overheating failure was investigated under a prototypical steam cooling condition inside target tubes. In the small leak, the difference of wastage resistivity was clarified among several tube materials such as 9-chrome steels. In regard to an analytical approach, a computer code LEAP (Leak Enlargement and Propagation) was developed on the basis of all of these experimental results. The code was used to validate the previously selected DBL of the prototype reactor, Monju, steam generator. This approach proved to be successful in spite of somewhat over-conservatism in the analysis. Moreover, LEAP clarified the effectiveness of a rapid steam dump and an enhanced leak detection system. The code improvement toward a realistic analysis is desired, however, to lessen the DBL for a future large plant and then the re-evaluation of the experimental data such as the size of secondary failure is under way. (author). 4 refs, 8 figs, 1 tab

Preliminary project of installation for separation tubes tests-ITTS

International Nuclear Information System (INIS)

Rocha, Z.

1984-01-01

A consolidation of actual ideas about installation, entitled ''Installation to separation tubes tests-ITTS'', expected to CDTN is presented. The project bases, the testing to be realized, the procedures to be obeyed during the operation, the components and the space required by installation and auxiliary equipments, the presumable origin of components (nacional and international), including a preliminary list of building and operation costs are described. (author) [pt

A comparative study to identify factors of caregiver burden between baby boomers and post baby boomers: a secondary analysis of a US online caregiver survey.

Science.gov (United States)

Kim, Heejung; Lee, Sangeun; Cheon, Jooyoung; Hong, Soyun; Chang, Mido

2018-05-02

Baby boomers' position in the caregiving context is shifting from caregiver to care recipient as the population ages. While the unique characteristics of baby boomer caregivers are well established in caregiving literature, there is limited information about the next caregiving group after the baby boomers. In this study, the sociodemographic and caregiving-related characteristics of the two generations are compared and specific factors contributing to caregiver burden between baby boomer and post baby boomer caregivers are identified. This cross-sectional and correlational study used secondary analysis of data from the National Alliance for Caregiving and the American Association of Retired Persons. A structured online survey was conducted in 2014 with randomly selected samples (n = 1069) in the United States focusing on sociodemographics, caregiving-related characteristics, and burden of care. Descriptive statistics, multivariate linear regression analyses, and Steiger's Z-test were used to identify group differences in multivariate factors related to caregiver burden in two generational groups. Baby boomers and post baby boomers experienced caregiver burden to a similar degree. Caregiving-related factors are more likely to increase burden of care than sociodemographics in both groups. Caregiving without choice and spending longer hours on caregiving tasks were common factors that increased the burden in both generational groups (all p values baby boomer caregivers reported additional challenges, such as unemployment during caregiving, the dual responsibility of both adult and child care, and a family relationship with the care recipient. Due to the aging population of baby boomers, post baby boomers encounter different challenges related to caregiving burden, which is often considered an additional workload in their life course. Current policy and program tailored to baby boomers should be re-designed to meet the different needs of emerging caregivers

Baby brain atlases.

Science.gov (United States)

Oishi, Kenichi; Chang, Linda; Huang, Hao

2018-04-03

The baby brain is constantly changing due to its active neurodevelopment, and research into the baby brain is one of the frontiers in neuroscience. To help guide neuroscientists and clinicians in their investigation of this frontier, maps of the baby brain, which contain a priori knowledge about neurodevelopment and anatomy, are essential. "Brain atlas" in this review refers to a 3D-brain image with a set of reference labels, such as a parcellation map, as the anatomical reference that guides the mapping of the brain. Recent advancements in scanners, sequences, and motion control methodologies enable the creation of various types of high-resolution baby brain atlases. What is becoming clear is that one atlas is not sufficient to characterize the existing knowledge about the anatomical variations, disease-related anatomical alterations, and the variations in time-dependent changes. In this review, the types and roles of the human baby brain MRI atlases that are currently available are described and discussed, and future directions in the field of developmental neuroscience and its clinical applications are proposed. The potential use of disease-based atlases to characterize clinically relevant information, such as clinical labels, in addition to conventional anatomical labels, is also discussed. Copyright © 2018. Published by Elsevier Inc.

What is my Baby Like? Representations Concerning the Baby in the Third Trimester of Pregnancy

Directory of Open Access Journals (Sweden)

Marta Pedreira

2015-11-01

Full Text Available AimTo investigate if during the third trimester of pregnancy fantasies emerge in the baby representations based on the information that pregnant women have on their real babies through ultrasound techniques.MethodA qualitative, descriptive and exploratory research based on a sample of 30 pregnant Portuguese women, whose average age is 32 years old, was developed. A socio-demographic questionnaire and a semi-directive interview entitled "Interview of Maternal Representations During Pregnancy – Revised Version" (IRMAG-R, Ammaniti & Tambelli, 2010 were employed.ResultsBaby representations are immersed in a fantasy dimension, which means that the imaginary baby is quite present in this phase of pregnancy. Pregnant women mainly attribute psychological characteristics to the babies, rather than physical characteristics. Regardless of the type of characteristics analysed, the preference for these characteristics emerges based on their wishes. Secondly, characteristics of the parents may also emerge. Fetal movements and information from ultrasound have no significant influence on the characterization of the baby.ConclusionDespite the development of ultrasound techniques, the imaginary baby defines parents representations about the baby on the third trimester of pregnancy. Consequently, a new understanding of how pregnant women experience the transition to the postnatal phase has to be considered.

Radiation dose to neonates on a Special Care Baby Unit

International Nuclear Information System (INIS)

Faulkner, K.; Barry, J.L.; Smalley, P.

1989-01-01

The skin entrance dose to neonates on a special care baby unit was estimated from a knowledge of the technique factors, X-ray tube output and backscatter factors. Normalized organ dose data were employed to estimate radiation dose to a number of critical organs. Methods of reducing radiation dose to neonates were investigated. Initially, this involved changing the radiographic technique factors and introducing a lead rubber adjustable collimator, placed on top of the incubator, in addition to light beam diaphragms on the X-ray tube. These modifications to the examination technique appeared to reduce average entrance dose per radiograph from 92 μGy, to 58 μGy, a reduction of 37%. Later, a rare-earth film-screen combination was introduced to replace existing fast calcium tungstate screens. This enabled average entrance dose per radiograph to be reduced to 39 μGy, a further reduction of 33%. The mean radiation dose to a neonate is mainly determined by the number of radiographs. (author)

Radiation dose to neonates on a Special Care Baby Unit

Energy Technology Data Exchange (ETDEWEB)

Faulkner, K.; Barry, J.L.; Smalley, P.

1989-03-01

The skin entrance dose to neonates on a special care baby unit was estimated from a knowledge of the technique factors, X-ray tube output and backscatter factors. Normalized organ dose data were employed to estimate radiation dose to a number of critical organs. Methods of reducing radiation dose to neonates were investigated. Initially, this involved changing the radiographic technique factors and introducing a lead rubber adjustable collimator, placed on top of the incubator, in addition to light beam diaphragms on the X-ray tube. These modifications to the examination technique appeared to reduce average entrance dose per radiograph from 92 ..mu..Gy, to 58 ..mu..Gy, a reduction of 37%. Later, a rare-earth film-screen combination was introduced to replace existing fast calcium tungstate screens. This enabled average entrance dose per radiograph to be reduced to 39 ..mu..Gy, a further reduction of 33%. The mean radiation dose to a neonate is mainly determined by the number of radiographs.

Obstruction of endotracheal tube with relevant respiratory acidosis during pediatric cardiac surgery

NARCIS (Netherlands)

Morei, N.M.; Mungroop, H. E.; Michielon, Guido; Scheeren, Thomas

2014-01-01

We describe a case of pediatric cardiac surgery in a 21- days old baby, in whom a nasal endotracheal tube (ETT) was inserted. At the end of surgery both ventilatory pressures and end-tidal CO2 increased suggesting airway obstruction. Suctioning of the ETT lumen did not relieve the problem, only ETT

Optimization of ultrasonic tube testing with concentric transducers

International Nuclear Information System (INIS)

Dufayet, J.-P.; Gambin, Raymond.

1978-01-01

In order to test tubes by ultrasonics without rotation, concentric transducers can be used with conical mirrors to detect transverse defects and with helical shaped mirrors to detect longitudinal defects. Further optimization studies have been carried out in order to bring the system highly operational. The respective advantages brought by the rotating screen or by our especially designed sectorial transducers are discussed [fr

[Efficient and rapid non-test tube cloning of Jatropha curcas].

Science.gov (United States)

Wang, Zhao-Yu; Lin, Jing-Ming; Xu, Zeng-Fu

2007-08-01

To develop a new technique for efficient and rapid non-test tube cloning of the medicinal and energy- producing plant Jatropha curcas. Using the mini-stem fragment (2-3 cm) of Jatropha curcas with merely one axillary bud as the explant, the effect of an auxin IBA concentration on the plantlet regeneration was studied. When treated with 1 mg/LIBA for 1h, the explants showed the most rapid propagation. The mini-stem fragments high root regeneration ratio (96.7%), short root regeneration period (18.2-/+2.0 d), large number of new roots per explant (6.3-/+1.8), and long total root length (6.8-/+3.5 cm), demonstrating that this technique can be a simple and efficient method for rapid non-test tube cloning of Jatropha curcas of potential industrial value.

Thermal-hydraulic tests of steam-generator tube-support-plate crevices. Volume 2. Appendixes I through S. Final report

International Nuclear Information System (INIS)

Cassell, D.S.; Vroom, D.W.

1983-01-01

A test program was conducted to determine for selected steam generator tube supports the thermal/hydraulic conditions at the inception of dryout as indicated by a tube wall temperature excursion, to determine the pressure drop across the supports, and to obtain photographic documentation of the flow upstream and downstream of the supports. A multi-tube steam generator model was used and testing performed over the range of typcal PWR steam generator operating conditions. These appendices contain information on instrumentation calibration, test model and loop calibration, error analysis, test model thermal-hydraulic analyses, index of lab materials and log sheets, index of two-phase flow still photographs, index of high speed movies and video, test data printouts, test model and loop fabrication drawings, procedure for silver brazing tubewall thermocouples, and procedure for esablishing tube-tube support line contact

75 FR 81788 - Revocation of Requirements for Full-Size Baby Cribs and Non-Full-Size Baby Cribs

Science.gov (United States)

2010-12-28

...-Size Baby Cribs and Non-Full- Size Baby Cribs AGENCY: Consumer Product Safety Commission. ACTION: Final... Safety Specification for Full-Size Baby Cribs,'' and ASTM F 406-10a, ``Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards.'' The crib standards that the CPSC is publishing...

Experiment data report for Semiscale Mod-1 Test S-28-1 (steam generator tube rupture test series)

International Nuclear Information System (INIS)

Collins, B.L.; Coppin, C.E.; Sackett, K.E.

1977-10-01

Recorded test data are presented for Test S-28-1 of the Semiscale Mod-1 steam generator tube rupture test series. These tests are among several Semiscale Mod-1 experiments conducted to investigate the thermal and hydraulic phenomena accompanying a hypothesized loss-of-coolant accident in a pressurized water reactor (PWR) system. Test S-28-1 was conducted from initial conditions of 15 767 kPa and 557 K to investigate the response of the Semiscale Mod-1 system to a depressurization and reflood transient following a simulated double-ended offset shear of the broken loop cold leg piping. During the test, cooling water was injected into the cold leg of the intact and broken loops to simulate emergency core coolant injection in a PWR. Sixty steam generator tube ruptures were simulated by a controlled injection from a heated accumulator into the intact loop hot leg

Baby Naps: Daytime Sleep Tips

Science.gov (United States)

... won't harm your baby. It's common for babies to cry when put down for sleep, but most will quiet themselves if left alone for a few minutes. If the crying lasts longer than a few minutes, check on your baby and offer comforting words. Then give him or ...

7 CFR 319.56-43 - Baby corn and baby carrots from Zambia.

Science.gov (United States)

2010-01-01

... § 319.56-43 Baby corn and baby carrots from Zambia. (a) Immature, dehusked “baby” sweet corn (Zea mays L... consignments only. (b) Immature “baby” carrots (Daucus carota L. ssp. sativus) for consumption measuring 10 to...

Eddy current tube testing unit

International Nuclear Information System (INIS)

Dufayet, J.P.; Duret, G.

1975-01-01

The unit described can check a wide variety of tubes in quick succession and its modular design gives it a high degree of versability. Suitably defined working conditions and specific fittings enable most of the faults encountered in the manufacture of a tube to be detected. By appropriate means of selection based on signal amplitude, phase and frequency analyses it is possible to adapt selection criteria to the seriousness of the different categories of defect [fr

75 FR 43107 - Revocation of Requirements for Full-Size Baby Cribs and Non-Full-Size Baby Cribs

Science.gov (United States)

2010-07-23

...] Revocation of Requirements for Full-Size Baby Cribs and Non-Full- Size Baby Cribs AGENCY: Consumer Product... standards, and include ASTM F 1169-10, ``Standard Consumer Safety Specification for Full-Size Baby Cribs,'' and ASTM F 406-10, ``Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards...

The Baby Boomers' intergenerational relationships.

Science.gov (United States)

Fingerman, Karen L; Pillemer, Karl A; Silverstein, Merril; Suitor, J Jill

2012-04-01

As Baby Boomers enter late life, relationships with family members gain importance. This review article highlights two aspects of their intergenerational relationships: (a) caregiving for aging parents and (b) interactions with adult children in the context of changing marital dynamics. The researchers describe three studies: (a) the Within Family Differences Study (WFDS) of mothers aged 65-75 and their multiple grown children (primarily Baby Boomers) ongoing since 2001; (b) the Family Exchanges Study (FES) of Baby Boomers aged 42-60, their spouses, parents, and multiple grown children ongoing since 2008; and (c) the Longitudinal Study of Generations (LSoG) of 351 three-generation families started when the Baby Boomers were teenagers in 1971, with interviews every 3-5 years from 1985 to 2005. These studies show that the Baby Boomers in midlife navigate complex intergenerational patterns. The WFDS finds aging parents differentiate among Baby Boomer children in midlife, favoring some more than others. The FES shows that the Baby Boomers are typically more involved with their children than with their aging parents; Boomers' personal values, family members' needs, and personal rewards shape decisions about support. The LSoG documents how divorce and remarriage dampen intergenerational obligations in some families. Moreover, loosening cultural norms have weakened family bonds in general. Reviews of these studies provide insights into how the Baby Boomers may negotiate caregiving for aging parents as well as the likelihood of family care they will receive when their own health declines in the future.

Grow, Baby, Grow

Science.gov (United States)

Maybe you quit smoking during your pregnancy. Or maybe you struggled and weren’t able to stay quit. Now that your baby is here, trying to stay away from smoking is still important. That’s because the chemicals in smoke can make it harder for your baby to grow like he or she should.

Fatigue testing on samples from Zircaloy-4 tubes type SEU-43

International Nuclear Information System (INIS)

Olaru, V.; Ionescu, V.; Nitu, A.; Ionescu, D.; Voicu, F.

2016-01-01

The paper presents the testing of samples worked from Zicaloy-4 tubes (as-received.. metallurgical state), utilized in the composition of the CANDU SEU-43 fuel bundle. These tests are intended to simulate their behaviour in a power cycling process inside the reactor. The testing process is of low cycle fatigue type, done outside of the reactor, on ''C-ring'' samples, cut along the transversal direction. These samples are tested at 1%, 2% and 3% amplitude deformation, at room temperature. The calibration curves for both types of tube (small and big diameter) are determined by using the finite element analyses with the ANSYS computer code. The cycling test results are in the form of a fatigue life curve (N-e) for zircaloy-4 used in the SEU-43 fuel bundle. The curve is determined by the experimental dependency between the number of cycles to fracture and the deformation amplitude. The low cycle fatigue mechanical tests done at room temperature together with electronic microscopy analyses have reflected the characteristic behaviour of the zircaloy-4 metal in the given environment conditions. (authors)

Limits to the Recognizability of Flaws in Non-Destructive Testing Steam-Generator Tubes for Nuclear-Power Plants

International Nuclear Information System (INIS)

Kuhlmann, A.; Adamsky, F.-J.

1965-01-01

In the Federal Republic of Germany there are nuclear reactors under construction with steam generators inside the reactor pressure-vessel. As a result design repairs of steam- generator tubes are very difficult and cause large shut-down times of the nuclear-power plant. It is known that numerous troubles in operating conventional power plants are results of steam-generator tube damages. Because of the high total costs of these reactors it. is necessary to construct the steam generators especially in such a manner that the load factor of the power plant is as high as possible. The Technischer Überwachungs-Verein Rheinland was charged to supervise and to test fabrication and construction of the steam generators to see that this part of the plant was as free of defects as possible. The experience gained during this work is of interest for manufacture and construction of steam generators for nuclear-power plants in general. This paper deals with the efficiency limits of non-destructive testing steam-generator tubes. The following tests performed will be discussed in detail: (a) Automatic ultrasonic testing of the straight tubes in the production facility; (b) Combined ultrasonic and radiographic testing of the bent tubes and tube weldings; (c) Other non-destructive tests. (author) [fr

Elastic Stability of Concentric Tube Robots: A Stability Measure and Design Test.

Science.gov (United States)

Gilbert, Hunter B; Hendrick, Richard J; Webster, Robert J

2016-02-01

Concentric tube robots are needle-sized manipulators which have been investigated for use in minimally invasive surgeries. It was noted early in the development of these devices that elastic energy storage can lead to rapid snapping motion for designs with moderate to high tube curvatures. Substantial progress has recently been made in the concentric tube robot community in designing snap-free robots, planning stable paths, and characterizing conditions that result in snapping for specific classes of concentric tube robots. However, a general measure for how stable a given robot configuration is has yet to be proposed. In this paper, we use bifurcation and elastic stability theory to provide such a measure, as well as to produce a test for determining whether a given design is snap-free (i.e. whether snapping can occur anywhere in the unloaded robot's workspace). These results are useful in designing, planning motions for, and controlling concentric tube robots with high curvatures.

Tests for development of estimation technology of reactor core deformation. Report No.1: fundamental mechanical properties of wrapper tube (test report)

International Nuclear Information System (INIS)

Nishiura, Takeo; Shimazaki, Yuji; Horikiri, Morito

1998-10-01

Mechanical properties such as local contact compression stiffness, bending stiffness, deformation properties, material properties, and friction properties of a wrapper tube structure were clarified experimentally, which can be used as the basic data for development of estimation technology of reactor core deformation. Contents of the Tests data as follows: (1) Effects of load supporting boundary conditions, whether or not a contact-proof pad is attached, and length of duct, on cross section deformation of wrapper tube were made clear as the local contact compression stiffness characteristics. (2) Bending stiffness does not depend on the difference of load supporting boundary conditions. The property of cross section deformation under bending load was obtained. (3) The deformation modes and the strain distributions were obtained by the deformation tests of wrapper tube. (4) The stress-strain diagrams including plastic range under various strain variation rates were obtained by the material tests at room temperature. (5) The static and the dynamic friction coefficients by various contact angles and the contact loads between contact-proof pads of two wrapper tubes were obtained by friction property tests. (author)

Safe Sleep for Babies

Science.gov (United States)

... 5 MB] Read the MMWR Science Clips Safe Sleep for Babies Eliminating hazards Recommend on Facebook Tweet ... Page Problem Every year, there are thousands of sleep-related deaths among babies. View large image and ...

Laundering Your Baby's Clothes

Science.gov (United States)

... Development Infections Diseases & Conditions Pregnancy & Baby Nutrition & Fitness Emotions & Behavior School & Family Life First Aid & Safety Doctors & ... for sensitive skin.) Unless your baby has allergies , eczema/atopic dermatitis , or another condition causing sensitive skin, ...

Preanalytical errors in primary healthcare: a questionnaire study of information search procedures, test request management and test tube labelling.

Science.gov (United States)

Söderberg, Johan; Brulin, Christine; Grankvist, Kjell; Wallin, Olof

2009-01-01

Most errors in laboratory medicine occur in the preanalytical phase and are the result of human mistakes. This study investigated information search procedures, test request management and test tube labelling in primary healthcare compared to the same procedures amongst clinical laboratory staff. A questionnaire was completed by 317 venous blood sampling staff in 70 primary healthcare centres and in two clinical laboratories (response rate = 94%). Correct procedures were not always followed. Only 60% of the primary healthcare staff reported that they always sought information in the updated, online laboratory manual. Only 12% reported that they always labelled the test tubes prior to drawing blood samples. No major differences between primary healthcare centres and clinical laboratories were found, except for test tube labelling, whereby the laboratory staff reported better practices. Re-education and access to documented routines were not clearly associated with better practices. The preanalytical procedure in the surveyed primary healthcare centres was associated with a risk of errors which could affect patient safety. To improve patient safety in laboratory testing, all healthcare providers should survey their preanalytical procedures and improve the total testing process with a systems perspective.

Boosting Your Baby's Brain Power

Science.gov (United States)

Engel-Smothers, Holly; Heim, Susan M.

2009-01-01

With more than 100 billion neurons that would stretch more than 60,000 miles, a newborn baby's brain is quite phenomenal! These neurons must generally form connections within the first eight months of a baby's life to foster optimal brain growth and lifelong learning. Mommies, daddies, and caregivers are extremely vital to ensuring babies reach…

Beliefs about the use of baby walkers.

Science.gov (United States)

Chagas, Paula S C; Mancini, Marisa C; Tirado, Marcella G A; Megale, Luiz; Sampaio, Rosana F

2011-01-01

To understand the opinion of the parents about the baby walker and compare the age of gait acquisition between infants that used a walker and those that did not. In this quali-quantitative study, an interview involving a semi-structured questionnaire was carried out with 26 parents, 14 of whose infants used the equipment (BWG) and 12 of whose infants did not (NBWG) prior to gait acquisition. After extensive content analysis, categories for interpreting the results emerged. For data triangulation, the age of gait acquisition was documented by weekly telephone contact. Student's t-test was used for comparison between groups with a significance level of α=0.05. The following categories were identified in the parents' reports: a) information about the baby walker; b) doubt/decision to use it vs. certainty about not using it; c) beliefs about the use of a baby-walker; and d) benefits and harm from use. The age of independent gait acquisition did not differ between groups (p=0.837): BWG initiated gait at 376.17 (SD=32.62) days and NBWG did so at 378.75 (SD=27.99) days. The beliefs and feelings that permeate the decision to use a baby walker illustrate the different rationales adopted by parents about the role of this equipment in the child's development of gait and autonomy. The use of a baby walker did not influence the age of gait acquisition. The results broaden the understanding of choices that influence child-rearing practices prior to gait acquisition.

The Baby Boomers’ Intergenerational Relationships

Science.gov (United States)

Fingerman, Karen L.; Pillemer, Karl A.; Silverstein, Merril; Suitor, J. Jill

2012-01-01

Purpose: As Baby Boomers enter late life, relationships with family members gain importance. This review article highlights two aspects of their intergenerational relationships: (a) caregiving for aging parents and (b) interactions with adult children in the context of changing marital dynamics. Design and Methods: The researchers describe three studies: (a) the Within Family Differences Study (WFDS) of mothers aged 65–75 and their multiple grown children (primarily Baby Boomers) ongoing since 2001; (b) the Family Exchanges Study (FES) of Baby Boomers aged 42–60, their spouses, parents, and multiple grown children ongoing since 2008; and (c) the Longitudinal Study of Generations (LSoG) of 351 three-generation families started when the Baby Boomers were teenagers in 1971, with interviews every 3–5 years from 1985 to 2005. Results: These studies show that the Baby Boomers in midlife navigate complex intergenerational patterns. The WFDS finds aging parents differentiate among Baby Boomer children in midlife, favoring some more than others. The FES shows that the Baby Boomers are typically more involved with their children than with their aging parents; Boomers’ personal values, family members’ needs, and personal rewards shape decisions about support. The LSoG documents how divorce and remarriage dampen intergenerational obligations in some families. Moreover, loosening cultural norms have weakened family bonds in general. Implications: Reviews of these studies provide insights into how the Baby Boomers may negotiate caregiving for aging parents as well as the likelihood of family care they will receive when their own health declines in the future. PMID:22250130

Tuboimpedance: A New Test of Eustachian Tube Function.

Science.gov (United States)

Smith, Matthew E; Zou, Charlie C; Blythe, Andrew J C; Tysome, James R

2017-04-01

Objective Eustachian tube (ET) dysfunction is most frequently caused by a failure of the ET to adequately open; however, there is currently no reliable method of assessing this. Tubomanometry has recently shown good interindividual repeatability as a measure of ET function by measuring middle ear pressure after the application of regulated nasopharyngeal pressures during swallowing. We present the first reports of a novel test: middle ear impedance measurements during standard nasopharyngeal pressure application (tuboimpedance). We assess repeatability in healthy ears and any advantages over tubomanometry. Study Design Exploratory cohort diagnosis study. Setting Tertiary referral center. Subjects Twenty screened, healthy ears (10 volunteers). Methods Tubomanometry and tuboimpedance tests were performed while individuals swallowed with applied nasopharyngeal pressures of 20, 30, 40, and 50 mbar. Eustachian tube opening detection rate and test repeatability (measured by intraclass correlation coefficient [ICC]) for immediate and delayed repeats at each pressure were compared. Results ET opening was detected more frequently using tuboimpedance, with a 100% detection rate using a nasopharyngeal pressure of 30 mbar or more, compared to 88% to 96% with tubomanometry. Detection of ET opening at 20 mbar was possible with tuboimpedance. Repeatability of both tests was mostly strong (ICC >0.7) for both immediate and delayed repeats. Repeatability for the tubomanometry R value was only fair to moderate. Conclusion Tuboimpedance may provide a repeatable measure of ET opening that is easier to perform due to lower nasopharyngeal pressures required and fewer issues with poor ear-probe sealing. Further assessment in patients with different forms of ET dysfunction is required.

Organic Baby Food: Better for Baby?

Science.gov (United States)

... al. Organic foods: Health and environmental advantages and disadvantages. Pediatrics. 2012;130:e1406. Morin K. Organic baby ... Policy Notice of Privacy Practices Notice of Nondiscrimination Advertising Mayo Clinic is a not-for-profit organization ...

Shaken baby symptoms (image)

Science.gov (United States)

... is a severe form of head injury caused by the baby's brain rebounding inside of the baby's skull when shaken. In this injury there is bruising of the brain, swelling, pressure, and bleeding (intracerebral hemorrhage). This can easily lead ...

Baby Poop: What's Normal?

Science.gov (United States)

... I'm breast-feeding my newborn and her bowel movements are yellow and mushy. Is this normal for baby poop? Answers from Jay L. Hoecker, M.D. Yellow, mushy bowel movements are perfectly normal for breast-fed babies. Still, ...

Tube suction test for evaluating durability of cementitiously stabilized soils.

Science.gov (United States)

2011-06-01

In a comprehensive laboratory study, different tests namely, unconfined compressive strength (UCS) at the end of freeze-thaw/wet-dry (F-T/W-D) cycles, resilient modulus (Mr) at the end of F-T/W-D cycles, vacuum saturation, tube suction, and moisture ...

Tube suction test for evaluating durability of cementitiously stabilized soils.

Science.gov (United States)

2011-06-01

In a comprehensive laboratory study, different tests namely, unconfined compressive strength (UCS) at the end of freeze-thaw/wet-dry (FT/ : W-D) cycles, resilient modulus (Mr) at the end of F-T/W-D cycles, vacuum saturation, tube suction, and moistur...

MODEL SEIR UNTUK EPIDEMI FLU BABI PADA POPULASI BABI DENGAN LAJU KONTAK JENUH

Directory of Open Access Journals (Sweden)

M Kharis

2012-09-01

Full Text Available Babi merupakan inang alami dari virus influensa yang secara anatomis, fisiologis, dan imunitas mirip (similar dengan yang ada pada manusia. Virus influenza subtipe A yang ada pada manusia yaitu H1N1, H3N2 dan H1N2 merupakan enzootic pada populasi babi di dunia. babi dapat terinfeksi oleh turunan-turunan virus influenza tipe A dari manusia maupun dari burung dan dalam hal ini dianggap sebagai inang sementara (Intermediate hosts dari turunan-turunan virus flu babi yang berpotensi menyebabkan epidemi bahkan pandemi. Evolusi antigenik dari virus influenza pada babi terjadi dengan laju sekitar 6 kali lebih lambat dibandingkan dengan virus influenza pada manusia. Dalam tulisan ini akan dikaji model matematika untuk epidemi flu babi pada populasi babi. Model yang diberikan merupakan model deterministik dengan laju kontak jenuh yang merupakan perumuman dari laju kontak standar. Perumuman ini dinyatakan dengan adanya probabilitas suatu individu melakukan kontak yang dinyatakan sebagai suatu fungsi dari populasi. Pengkajian yang dilakukan meliputi penentuan titik ekuilibrium model matematika dan analisa kestabilannya. Diharapkan hasil kajian ini dapat bermanfaat dalam penanggulangan wabah flu babi pada sumber utama yaitu populasi babi sehingga dapat dilakukan pencegahan sebelum mewabah di populasi manusia. Pigs are a natural host of influenza virus that are similar anatomically, physiologically, and immunity which in humans. Influenza viruses of A subtype in humans are H1N1, H3N2 and H1N2. They are enzootic in the swine population in the world. Pigs can be infected by strains of type A influenza viruses from humans or from birds. Pigs are considered as a temporary host (intermediate hosts of the derivatives of the swine flu virus that has the potential to cause epidemics and even pandemics. Antigenic evolution of influenza viruses in pigs occurred at rate about 6 times slower than the influenza viruses in humans. In this paper the mathematical model

Forming limit diagram of aluminum AA6063 tubes at high temperatures by bulge tests

International Nuclear Information System (INIS)

Hashemi, Seyed Jalal; Naeini, Hassan Moslemi; Liaghat, Gholamhossein; Tafti, Rooholla Azizi; Rahmani, Farzad

2014-01-01

A free bulge test and ductile fracture criteria were used to obtain the forming limit diagrams (FLD) of aluminum alloy AA6063 tubes at high temperatures. Ductile fracture criteria were calibrated using the results of uniaxial tension tests at various elevated temperatures and different strain rates through adjusting the Zener-Holloman parameter. High temperature free bulge test of tubes was simulated in finite element software Abaqus, and tube bursting was predicted using ductile fracture criteria under different loading paths. FLDs which were obtained from finite element simulation were compared to experimental results to select the most accurate criterion for prediction of forming limit diagram. According to the results, all studied ductile fracture criteria predict similarly when forming condition is close to the uniaxial tension, while Ayada criterion predicts the FLD at 473 K and 573 K very well.

Forming limit diagram of aluminum AA6063 tubes at high temperatures by bulge tests

Energy Technology Data Exchange (ETDEWEB)

Hashemi, Seyed Jalal; Naeini, Hassan Moslemi; Liaghat, Gholamhossein [Tarbiat Modares University, Tehran (Iran, Islamic Republic of); Tafti, Rooholla Azizi [Yazd University, Yazd (Iran, Islamic Republic of); Rahmani, Farzad [Kar Higher Education Institute, Qazvin (Iran, Islamic Republic of)

2014-11-15

A free bulge test and ductile fracture criteria were used to obtain the forming limit diagrams (FLD) of aluminum alloy AA6063 tubes at high temperatures. Ductile fracture criteria were calibrated using the results of uniaxial tension tests at various elevated temperatures and different strain rates through adjusting the Zener-Holloman parameter. High temperature free bulge test of tubes was simulated in finite element software Abaqus, and tube bursting was predicted using ductile fracture criteria under different loading paths. FLDs which were obtained from finite element simulation were compared to experimental results to select the most accurate criterion for prediction of forming limit diagram. According to the results, all studied ductile fracture criteria predict similarly when forming condition is close to the uniaxial tension, while Ayada criterion predicts the FLD at 473 K and 573 K very well.

Heat transfer test in a tube using CO2 at supercritical pressures

International Nuclear Information System (INIS)

Kim, Hwan Yeol; Kim, Hyungrae; Song, Jin Ho; Cho, Bong Hyun; Bae, Yoon Yeong

2005-01-01

Heat transfer test facility, which is named as SPHINX (Supercritical Pressure Heat Transfer Investigation for NeXt Generation), has been constructed in KAERI for the study of heat transfer and pressure drop characteristics in a single tube, single rod and rod bundle at supercritical CO 2 conditions. The tests with supercritical water are difficult it terms of cost and effort, since the critical pressure and temperature of water are as high as 22.12 MPa and 374.14degC. As a substitute for water, CO 2 is selected for the test since the critical pressure and temperature of CO 2 are 7.38 MPa and 31.05degC that are much lower than those of water. This paper describes the design characteristics of the SPHINX and the experimental investigations on the heat transfer and pressure drop of a vertical single tube with an inside diameter of 4.4 mm with upward flow of supercritical CO 2 . The geometry of the single tube is the same as that of Kyushu University test performed with Freon (R22) for the direct comparison of a medium effect. The tests were performed with various heat and mass fluxes at a given pressure. The range of mass flux is 400∼1200 kg/m 2 s and the heat flux is chosen up to 150 kW/m 2 . The selected pressure are 7.75, 8.12, and 8.85 MPa. The test results are investigated and compared with the previous tests. (author)

Skin care for healthy babies at term: A systematic review of the evidence.

Science.gov (United States)

Cooke, Alison; Bedwell, Carol; Campbell, Malcolm; McGowan, Linda; Ersser, Steven J; Lavender, Tina

2018-01-01

to identify what skin practices are important for the protection of baby skin in healthy term babies (0-6 months) and generate evidence-based conclusions to inform health professionals and parents. eleven databases were searched for all empirical quantitative and qualitative research published between 2000-2015 which explored baby skin care for bathing and cleansing, nappy care, hair and scalp care, management of dry skin or baby massage, for healthy term babies up to 6 months old. Papers not published in English were excluded. A total of 3062 papers were identified. Pairs of reviewers assessed all citations and extracted data independently. There were 26 included papers: 16 RCTs, 3 non-randomised experimental studies, 1 mixed-methods study and 6 qualitative studies. Primary and secondary outcome measures were analysed using meta-analysis or narrative descriptive statistics. Synthesis of qualitative data was not possible due to disparity of the evidence. from the small numbers of studies with comparable data, there was no evidence of any significant differences between tested wash products and water or tested baby wipes and water. There was some evidence to suggest that daily use of full-body emollient therapy may help to reduce the risk of atopic eczema in high risk babies with a genetic predisposition to eczema; however, the use of olive oil or sunflower oil for baby dry skin may adversely affect skin barrier function. There was no evidence about hair/scalp care or baby massage. Qualitative research indicates that parents and health professionals believe that water alone is best. meta-analysis was restricted due to the lack of consistency of study outcome measures. Although there is considerable RCT evidence comparing the use of specific products against water alone, or another product, for bathing, cleansing and nappy care, the power of this evidence is reduced due to inconsistency of outcome measures in terms of outcome, treatment site or time-point. The

(AGA) Pre Term Babies

African Journals Online (AJOL)

Haematological Indices in Healthy Appropriate For-Gestational-Age (AGA) Pre Term Babies. ... International Journal of Medicine and Health Development. Journal Home ... Patient and Methods: All consecutive healthy pre-term new born babies delivered at UNTH and admitted into the hospital NBSCU were included.

Baby-MIND neutrino detector

Science.gov (United States)

Mefodiev, A. V.; Kudenko, Yu. G.; Mineev, O. V.; Khotjantsev, A. N.

2017-11-01

The main objective of the Baby-MIND detector (Magnetized Iron Neutrino Detector) is the study of muon charge identification efficiency for muon momenta from 0.3 to 5 GeV/ c. This paper presents the results of measurement of the Baby-MIND parameters.

History of the water chemistry for the few tube test model

International Nuclear Information System (INIS)

Moss, S.A.; Simpson, J.L.

1979-09-01

The water chemistry activities carried out in support of the Few Tube Test are described. This test was conducted to provide design confirmation data for the Clinch River Breeder Reactor Project (CRBRP) steam generators. Proposed CRBRP chemistry was followed; all volatile treatment (AVT) of water was carried out with on-line monitoring capability

Experimental investigation of thermal-hydraulic performance of PCCS with horizontal tube heat exchangers: single U-tube test

International Nuclear Information System (INIS)

Nakamura, Hideo; Anoda, Yoshinari; Arai, Kenji; Kurita, Tomohisa

2000-01-01

JAERI and JAPC started a cooperative study to verify performance of a PCCS (Passive Containment Cooling System) using horizontal heat exchanger for next-generation BWR in 1998. A test facility with a horizontal single U-tube was constructed in JAERI in 1999 to investigate fundamental condensation behavior under influences of non-condensable gas. Preliminary pre-test analyses were performed using RELAP5/ MOD3.2.1.2 code to expect the experimental outcomes by incorporating a correlation for condensation degradation because of non-condensable gas by Ueno et al. for better prediction. Preliminary results from both experiments (shakedown) and pre-test analyses indicated that the PCCS using horizontal U-tube heat exchanger is promising. Steam generated under assumed severe accident conditions; steam generation rate approx. = 1% core power, non-condensable gas concentration of 1% and simulated containment vessel pressure of 0.7 MPa, was totally condensed with a small differential pressure across inlet and outlet plenum. Experimental data will be accumulated to develop models and correlations for a better prediction of responses of the PCCS using horizontal heat exchanger during postulated severe accidents. (author)

Application of automatic inspection system to nondestructive test of heat transfer tubes of primary pressurized water cooler in the high temperature engineering test reactor. Joint research

International Nuclear Information System (INIS)

Takeda, Takeshi; Furusawa, Takayuki

2001-07-01

Heat transfer tubes of a primary pressurized water cooled (PPWC) in the high temperature engineering test reactor (HTTR) form the reactor pressure boundary of the primary coolant, therefore are important from the viewpoint of safety. To establish inspection techniques for the heat transfer tubes of the PPWC, an automatic inspection system was developed. The system employs a bobbin coil probe, a rotating probe for eddy current testing (ECT) and a rotating probe for ultrasonic testing (UT). Nondestructive test of a half of the heat transfer tubes of the PPWC was carried out by the automatic inspection system during reactor shutdown period of the HTTR (about 55% in the maximum reactor power in this paper). The nondestructive test results showed that the maximum signal-to-noise ratio was 1.8 in ECT. Pattern and phase of Lissajous wave, which were obtained for the heat transfer tube of the PPWC, were different from those obtained for the artificially defected tube. In UT echo amplitude of the PPWC tubes inspected was lower than 20% of distance-amplitude calibration curve. Thus, it was confirmed that there was no defect in depth, which was more than the detecting standard of the probes, on the outer surface of the heat transfer tubes of the PPWC inspected. (author)

Quantum entanglement of baby universes

International Nuclear Information System (INIS)

Aganagic, Mina; Okuda, Takuya; Ooguri, Hirosi

2007-01-01

We study quantum entanglements of baby universes which appear in non-perturbative corrections to the OSV formula for the entropy of extremal black holes in type IIA string theory compactified on the local Calabi-Yau manifold defined as a rank 2 vector bundle over an arbitrary genus G Riemann surface. This generalizes the result for G=1 in hep-th/0504221. Non-perturbative terms can be organized into a sum over contributions from baby universes, and the total wave-function is their coherent superposition in the third quantized Hilbert space. We find that half of the universes preserve one set of supercharges while the other half preserve a different set, making the total universe stable but non-BPS. The parent universe generates baby universes by brane/anti-brane pair creation, and baby universes are correlated by conservation of non-normalizable D-brane charges under the process. There are no other source of entanglement of baby universes, and all possible states are superposed with the equal weight

Quantum entanglement of baby universes

International Nuclear Information System (INIS)

Essman, Eric P.; Aganagic, Mina; Okuda, Takuya; Ooguri, Hirosi

2006-01-01

We study quantum entanglements of baby universes which appear in non-perturbative corrections to the OSV formula for the entropy of extremal black holes in type IIA string theory compactified on the local Calabi-Yau manifold defined as a rank 2 vector bundle over an arbitrary genus G Riemann surface. This generalizes the result for G=1 in hep-th/0504221. Non-perturbative terms can be organized into a sum over contributions from baby universes, and the total wave-function is their coherent superposition in the third quantized Hilbert space. We find that half of the universes preserve one set of supercharges while the other half preserve a different set, making the total universe stable but non-BPS. The parent universe generates baby universes by brane/anti-brane pair creation, and baby universes are correlated by conservation of non-normalizable D-brane charges under the process. There are no other source of entanglement of baby universes, and all possible states are superposed with the equal weight

Baby universes

International Nuclear Information System (INIS)

Strominger, A.

1988-01-01

This paper discusses how the subject of baby universes and their effects on spacetime coupling constants is in its infancy and rapidly developing. The subject is based on the non-existent (even by physicists' standards) Euclidean formulation of quantum gravity, and it is therefore necessary to make a number of assumptions in order to proceed. Nevertheless, the picture which has emerged is quite appealing: all spacetime coupling constants become dynamical variables when the effects of baby universes are taken into account. This fact might even solve the puzzle of the cosmological constant. The subject therefore seems worth further investigation

Recognition of a Baby's Emotional Cry Towards Robotics Baby Caregiver

OpenAIRE

Yamamoto, Shota; Yoshitomi, Yasunari; Tabuse, Masayoshi; Kushida, Kou; Asada, Taro

2013-01-01

We developed a method for pattern recognition of baby's emotions (discomfortable, hungry, or sleepy) expressed in the baby's cries. A 32-dimensional fast Fourier transform is performed for sound form clips, detected by our reported method and used as training data. The power of the sound form judged as a silent region is subtracted from each power of the frequency element. The power of each frequency element after the subtraction is treated as one of the elements of the feature vector. We per...

Chemical cleaning specification: few tube test model

International Nuclear Information System (INIS)

Hampton, L.V.; Simpson, J.L.

1979-09-01

The specification is for the waterside chemical cleaning of the 2 1/4 Cr - 1 Mo steel steam generator tubes. It describes the reagents and conditions for post-chemical cleaning passivation of the evaporator tubes

Calculation of fuel element temperature TRIGA 2000 reactor in sipping test tubes using CFD

International Nuclear Information System (INIS)

Sudjatmi KA

2013-01-01

It has been calculated the fuel element temperature in the sipping test of Bandung TRIGA 2000 reactor. The calculation needs to be done to ascertain that the fuel element temperatures are below or at the limit of the allowable temperature fuel elements during reactor operation. ensuring that the implementation of the test by using this device, the temperature is still within safety limits. The calculation is done by making a model sipping test tubes containing a fuel element surrounded by 9 fuel elements. according to the position sipping test tubes in the reactor core. by using Gambit. Dimensional model adapted to the dimensions of the tube and the fuel element in the reactor core of Bandung TRIGA 2000 reactor. Sipping test Operation for each fuel element performed for 30 minutes at 300 kW power. Calculations were performed using CFD software and as input adjusted parameters of TRIGA 2000 reactor. Simulations carried out on the operation of the 30, 60, 90, 120, 150, 180 and 210 minutes. The calculation result shows that the temperature of the fuel in tubes sipping test of 236.06 °C, while the temperature of the wall is 87.58 °C. The maximum temperature in the fuel center of TRIGA 2000 reactor in normal operation is 650 °C. and the boiling is not allowed in the reactor. So it can be concluded that the operation of the sipping test device are is very safe because the fuel center temperature is below the temperature limits the allowable fuel under normal operating conditions as well as the fuel element wall temperature is below the boiling temperature of water. (author)

Standardized procedure for eddy-current testing of stainless steel, thin-walled nuclear fuel element cladding tubes

Energy Technology Data Exchange (ETDEWEB)

Barat, P; Raj, B; Bhattacharya, D K [Reactor Research Centre, Kalpakkam (India)

1982-10-01

Thin-walled nuclear fuel cladding tubes made of AISI 316 stainless steel have been examined by eddy-current testing. Standardization of the procedures has required investigations on optimizing the test frequency, finding a method to locate a defect with respect to the probe reference end, and the use of standard defects and sequential metallography of natural defects detected by eddy-current testing, to understand the influence of the nature of defects on the impedance output signals. Test frequency and method of locating the defect were optimized by the use of standard defects made by machining in reference cladding tubes. Subsequent metallography of natural defects detected by eddy-current testing revealed mainly clusters of inclusions but also other types of defects. The effect of the distribution of inclusions along the length of the tube on the impedance output is discussed.

Acute appendicitis in a premature baby

International Nuclear Information System (INIS)

Beluffi, Giampiero; Alberici, Elisa

2002-01-01

A case of acute appendicitis in a premature baby in whom diagnosis was suggested on plain films of the abdomen is presented. In this baby air in a hollow viscus suspected of being an enlarged appendix was the clue to diagnosis. The diagnostic dilemma of this rare and life-threatening condition in premature babies and newborns is underlined. The relevance of different imaging modalities and of different findings in this age group is discussed. Awareness of this rare condition and possible differential diagnosis in newborns and premature babies is stressed. (orig.)

Testing external surface of fuel element tubes for power nuclear reactors

International Nuclear Information System (INIS)

Naugol'nykh, O.G.; Nelyubin, Yu.V.

1987-01-01

Optical methods are regarded perspective for discovery and detection of flaws of external surfaces of fuel element tubes. The TV method has highest information content among them. Two mock-ups of facilities based on the TV method using a ''dissector'' type TV device and a TV tube with charge accumulation (vidikon) have been developed. It is concluded that complex testing - combination of ultrasonic, photoelectric and TV methods in a facility is necessary for discovery and analysis of the whole variety of flaws, though sensitivity of the TV method is enough for disclosure of all the main defects

Fast neutron radiography testing for components of launch vehicles by a baby-cyclotron

International Nuclear Information System (INIS)

Ikeda, Y.; Ohkubo, K.; Matsumoto, G.; Nakamura, T.; Nozaki, Y.; Wakasa, S.; Toda, Y.; Kato, T.

1990-01-01

Recently, neutron radiography (NR) has become an important means of nondestructive testing (NDT) in Japan. Especially thermal neutron radiography testing (NRT) has been used for the NDT of various explosive devices of launch vehicles, which are developed as a H-series program by the National Space Development Agency (NASDA) of Japan. The NRT for launch vehicles has been carried out at the NR facility of a baby-cyclotron. In the NRT a conventional film method based on silver-halide emulsion has been exclusively employed to inspect various testing objects including components, and many valuable results have been obtained so far successfully. However, recently, the launch vehicles to be shot up have become much larger. With larger launch vehicles, the parts used in them have also become larger and thicker. One main disadvantage of the NRT by thermal neutrons is somewhat weak penetrability through objects because the energy is small. With the conventional thermal neutron radiography (TNR), steel objects being thicker than 40 to 50 mm are difficult to test through them because scattered neutrons obstruct real image of the object. Consequently a new method of NRT should be developed instead of TNR and applied to the new components of H-2 launch vehicles. In order to cope with the requirement, fast neutron radiography (FNR) has been studied for testing the new components of H-2, such as large separation bolts

Studies of the steam generator degraded tubes behavior on BRUTUS test loop

Energy Technology Data Exchange (ETDEWEB)

Chedeau, C.; Rassineux, B. [EDF/DER/MTC, Moret Sur Loing (France); Flesch, B. [EDF/EPN/DMAINT, Paris (France)] [and others

1997-04-01

Studies for the evaluation of steam generator tube bundle cracks in PWR power plants are described. Global tests of crack leak rates and numerical calculations of crack opening area are discussed in some detail. A brief overview of thermohydraulic studies and the development of a mechanical probabilistic design code is also given. The COMPROMIS computer code was used in the studies to quantify the influence of in-service inspections and maintenance work on the risk of a steam generator tube rupture.

T P Nafeesa Baby

Indian Academy of Sciences (India)

Home; Journals; Pramana – Journal of Physics. T P Nafeesa Baby. Articles written in Pramana – Journal of Physics. Volume 80 Issue 2 February 2013 pp 289-294 Research Articles. Plasma excitations in a single-walled carbon nanotube with an external transverse magnetic field · K A Vijayalakshmi T P Nafeesa Baby.

Wastage-resistant characteristics of 12Cr steel tube material. Small leak sodium-water reaction test

International Nuclear Information System (INIS)

Shimoyama, Kazuhito

2004-03-01

In the water leak accident of a steam generator designed for a sodium cooled reactor in the Feasibility Study, the localization of tube failure propagation by using an advanced water leak detector will be required from the viewpoints of the safety and economical efficiency of the plant. So far, the conventional knowledge and analytical tools have been used in the investigation and evaluation of water leak phenomenon; nevertheless, there was neither test data nor the study of quantitative evaluation on the corrosion behavior, so-called wastage-resistant characteristics, of 12Cr steel tube material in sodium-water reactions. Wastage tests for the 12Cr steel tube material were conducted in small water leaks by use of the Sodium-Water Reaction Test Rig (SWAT-1R), and the data of wastage rate were obtained in the parameter of water leak rate under the constant sodium temperature and distance between leak and target tubes. The test results lead to the following conclusions: (1) The wastage-resistibility of 12Cr steel is 1.6 times greater than that of 9Cr steel and is 2.7 times greater than that of 2.25Cr-1Mo steel. (2)The wastage-resistibility of 12Cr steel increases in smaller water leaks; especially in water leak rates of 1 g/sec or less, it is more excellent than that of SUS321 stainless steel used as Monju superheater tube material. (3) Based on the correlation of wastage rate for the 9Cr steel, the correlation for the 12Cr steel has been obtained to be used for the evaluation of tube failure propagation. As the correlation of wastage rate for the 12Cr steel is based on the correlation for the 9Cr steel, it gives enough conservatism in smaller water leaks. To serve in accurately evaluating the tube failure propagation in smaller water leaks, it is necessary to obtain new correlation of wastage rate for the 12Cr steel based on the data in the wide range of water leak rates. (author)

Mothers' use of and attitudes to BabyCheck.

OpenAIRE

Thomson, Hilary; Ross, Sue; Wilson, Philip; McConnachie, Alex; Watson, Richard

2002-01-01

A copy of BabyCheck was sent to 497 mothers shortly after the birth of their baby. Six months later they were sent a questionnaire asking about their use of and attitudes to, BabyCheck. Questionnaires were returned by 323 (65%) mothers; 215 (67%) of them reported reading BabyCheck, the majority found it easy to understand (74%) and agreed with the advice (67%). Eighty-four (26%) of the mothers who returned the questionnaires reported using BabyCheck when their baby was ill; of these, 71% agre...

High-voltage test and training of plastic streamer tubes for the DELPHI hadron calorimeter

International Nuclear Information System (INIS)

Alekseev, G.D.; Cellar, S.; Khomenko, B.A.; Korytov, A.V.; Kulinich, P.A.; Micelmacher, G.V.; Sedykh, Yu.V.; Toledo, R.

1987-01-01

The results of high-voltage test and training of plastic streamer tubes of the DELPHI hadron calorimeter are presented. The testing technique is considered in detail. The equipment for high-voltage training consists of a mini-computer, CAMAC-electronics, a controllable high-voltage supply and a digital ampermeter. The experimental results shows that high-voltage training of streamer tubes improves their characteristics. The value of dark current decreased up to 1 μA. The operational voltage range increased by a value more than 300 V

CASE REPORT Mermaid baby

African Journals Online (AJOL)

SA JOURNAL OF RADIOLOGY • September 2010. Abstract. We were recently intrigued by a baby born at Kalafong Hospital with fused lower extremities resembling a mermaid, which caused us to search for the background and origin of this entity called sirenomelia. Case report. A 40-year-old woman delivered a baby at 36 ...

Collodion Baby - a Case Report

Directory of Open Access Journals (Sweden)

Stojanović Vesna

2014-12-01

Full Text Available Colloidon baby describes a highly characteristic clinical entity in newborns encased in a yellowish translucent membrane resembling collodion. In most cases the condition either precedes the development of one of a variety of ichthyoses, the commonest of which are lamellar ichthyosis and non-bullous ichthyosiform erythroderma, or occasionally represents an initial phase of other ichthyoses such as ichthyosis vulgaris. In at least 10% of all cases of collodion baby, the condition is followed by a mild ichthyosis of lamellar type, so mild as to be considered more or less normal, so-called self-healing collodion baby or ‘lamellar ichthyosis of the newborn’. In this report we present a rare case of collodion baby in whom, after collodion membrane peeled-off, the skin retained normal appearance.

Pollen tube growth test (PTGT) in environmental biomonitoring and predictive radiation biology studies: problem and prospect

International Nuclear Information System (INIS)

Pandey, Devi D.

2012-01-01

In Environmental and Human Bio monitoring studies of Hazardous xenobiotics over living system particularly at cell level, it is desirable to have easy and sensitive test system like Cell Viability assay, MNT, Cell Culture photo toxicity Test, PTGT etc. Out of these the PTGT quite better than other because the in vitro culture of pollen grain can provides a sensitive indication of toxicity at cellular level, since germination and growth of pollen tube will inhibited in presence of toxic substance like DDT, Heavy metal, even Radionuclide's. This test system is easy, economical and widely accepted through out world. In PTGT pollen tube never containing Chloroplast or other plastids so pollen tube resembles animals more than a plant organ and is therefore also a suitable as model for Genotoxicity Assessment of compounds harmful to animal and humans. Lack of plastids in PT, PTGT will not identify the toxic effect of compounds that targets Non cyclic and cyclic photoposphorylation of photosynthesis. This test system valid in International Toxicity Testing Protocol. But this method is time consuming and problem in measurement of pollen tube growing in a culture medium became usually bent and make measurement difficult. Other disadvantage of this method is requirement of DMSO to dissolve test substance of low water suitability in culture medium. DMSO shown to have no effect on PTG at Concentration not more than 1% but some extent interfere with results. Values of PTG are quantified in ED50/IC50 that is the concentration of test compounds that reduces pollen tube growth to 50% of control. So PTGT could be very sensitive and easy to assess in common lab in International way. (author)

["Designer baby" changed to French for "double hope baby"].

Science.gov (United States)

Fagniez, P-L; Loriau, J; Tayar, C

2005-10-01

Scientific advances during the last decades regarding potential intervention on embryos arouse many questions in society to prepare the ground concerning the limits that should be set for these practices. For the first time in 1994, a parliamentary proceeding allowed the definition of a French model of bioethics through laws of the same name. These laws, among others, authorized in a well and strictly defined setting the practice of preimplantation genetic diagnosis (PGD). Because of technical progress concerning PGD, new questions arose, especially concerning the accomplishment of designer babies. The French Chamber of Representatives came in with a new law that banishes the concept of designer babies and replaces it with another concept: double hope babies, in French "bébé du double espoir". A first hope of a pregnancy giving birth to a healthy child and the second being that this child conceived with the aid of PGD could help treat an elder brother. Because of the issuing of two specific laws in a ten years interval, France occupies a privileged place in a Europe where bioethical issues continue to be debated, particularly PGD.

Can serums be replaced by Mueller‑Hinton agar in germ tube test ...

African Journals Online (AJOL)

Background: The germ tube test (GTT) is inexpensive, easy, and well‑defined test that differentiates Candida albicans (excluding Candida dubliniensis and Candida africana) from other species. The aim of this study was to evaluate various serums (i.e., human, rabbit, horse, and fetal bovine serum) used in the GTT and ...

Rotational Symmetry Breaking in Baby Skyrme Models

Science.gov (United States)

Karliner, Marek; Hen, Itay

We discuss one of the most interesting phenomena exhibited by baby skyrmions - breaking of rotational symmetry. The topics we will deal with here include the appearance of rotational symmetry breaking in the static solutions of baby Skyrme models, both in flat as well as in curved spaces, the zero-temperature crystalline structure of baby skyrmions, and finally, the appearance of spontaneous breaking of rotational symmetry in rotating baby skyrmions.

Your baby and the flu

Science.gov (United States)

Babies and the flu; Your infant and the flu; Your toddler and the flu ... FLU SYMPTOMS IN INFANTS AND TODDLERS The flu is an infection of the nose, throat, and (sometimes) lungs. Call your baby's provider if ...

Eddy-current tests on operational evaluation of steam generator tubes in nuclear power plants

International Nuclear Information System (INIS)

Lopez, Luiz Antonio Negro Martin; Ting, Daniel Kao Sun

2000-01-01

This paper presents a worldwide research on the technical and economical impacts due to failure in tube bundles of nuclear power plant steam generators. An Eddy current non destructive test using Foucault currents for the inspection and failure detection on the tubes, and also the main type of defects. The paper also presents the signals generated by a Zetec MIZ-40 test equipment. This paper also presents a brief description of an automatic system for data analysis which is under development by using a fuzzy logic and artificial intelligence

Design and fabrication of hafnium tube to control the power of the irradiation test fuel in HANARO

Energy Technology Data Exchange (ETDEWEB)

Kim, D. H.; Lee, C. B.; Kim, Y. M.; Yang, Y. S.; Jung, Y. H

2003-05-01

For the irradiation test at HANARO, non-instrumentation capsule was manufactured and hafnium tube was used to control LHGR of HANARO. Hafnium tube can control the irradiation condition of HANARO similar to that of commercial reactor. Hafnium tube thickness was determined by the LHGR calculated at OR-4 irradiation hole to be installed the non-instrumented capsule. To fabricate the hafnium tube with hafnium plate, the fabrication method was determined by using the hafnium mechanical properties. And the tensile strength of hafnium was confirmed by tensile test. This report is confirmed the LHGR control at the OR-4 and the Hafnium fabrication for in used which the AFPCAP non-instrumented irradiation capsule.

Investigation of restricted baby Skyrme models

International Nuclear Information System (INIS)

Adam, C.; Romanczukiewicz, T.; Wereszczynski, A.; Sanchez-Guillen, J.

2010-01-01

A restriction of the baby Skyrme model consisting of the quartic and potential terms only is investigated in detail for a wide range of potentials. Further, its properties are compared with those of the corresponding full baby Skyrme models. We find that topological (charge) as well as geometrical (nucleus/shell shape) features of baby Skyrmions are captured already by the soliton solutions of the restricted model. Further, we find a coincidence between the compact or noncompact nature of solitons in the restricted model, on the one hand, and the existence or nonexistence of multi-Skyrmions in the full baby Skyrme model, on the other hand.

Lactate: creatinine ratio in babies with thin meconium staining of amniotic fluid

Science.gov (United States)

Ojha, Rishi Kant; Singh, Saroj K; Batra, Sanjay; Sreenivas, V; Puliyel, Jacob M

2006-01-01

Background ACOG states meconium stained amniotic fluid (MSAF) as one of the historical indicators of perinatal asphyxia. Thick meconium along with other indicators is used to identify babies with severe intrapartum asphyxia. Lactate creatinine ratio (L: C ratio) of 0.64 or higher in first passed urine of babies suffering severe intrapartum asphyxia has been shown to predict Hypoxic Ischaemic Encephalopathy (HIE). Literature review shows that meconium is passed in distress and thin meconium results from mixing and dilution over time, which may be hours to days. Thin meconium may thus be used as an indicator of antepartum asphyxia. We tested L: C ratios in a group of babies born through thin and thick meconium, and for comparison, in a group of babies without meconium at birth. Methods 86 consecutive newborns, 36 to 42 weeks of gestation, with meconium staining of liquor, were recruited for the study. 52 voided urine within 6 hours of birth; of these 27 had thick meconium and 25 had thin meconium at birth. 42 others, who did not have meconium or any other signs of asphyxia at birth provided controls. Lactate and creatinine levels in urine were tested by standard enzymatic methods in the three groups. Results Lactate values are highest in the thin MSAF group followed by the thick MSAF and controls. Creatinine was lowest in the thin MSAF, followed by thick MSAF and controls. Normal babies had an average L: C ratio of 0.13 (± 0.09). L: C ratio was more among thin MSAF babies (4.3 ± 11.94) than thick MSAF babies (0.35 ± 0.35). Median L: C ratio was also higher in the thin MSAF group. Variation in the values of these parameters is observed to be high in the thin MSAF group as compared to other groups. L: C ratio was above the cutoff of 0.64 of Huang et al in 40% of those with thin meconium. 2 of these developed signs of HIE with convulsions (HIE Sarnat and Sarnat Stage II) during hospital stay. One had L: C Ratio of 93 and the other of 58.6. A smaller proportion (20

[Babies with cranial deformity].

Science.gov (United States)

Feijen, Michelle M W; Claessens, Edith A W M Habets; Dovens, Anke J Leenders; Vles, Johannes S; van der Hulst, Rene R W J

2009-01-01

Plagiocephaly was diagnosed in a baby aged 4 months and brachycephaly in a baby aged 5 months. Positional or deformational plagio- or brachycephaly is characterized by changes in shape and symmetry of the cranial vault. Treatment options are conservative and may include physiotherapy and helmet therapy. During the last two decades the incidence of positional plagiocephaly has increased in the Netherlands. This increase is due to the recommendation that babies be laid on their backs in order to reduce the risk of sudden infant death syndrome. We suggest the following: in cases of positional preference of the infant, referral to a physiotherapist is indicated. In cases of unacceptable deformity of the cranium at the age 5 months, moulding helmet therapy is a possible treatment option.

Status of the bench-test system for the tubes in the HIMAC DTL linac

International Nuclear Information System (INIS)

Fujimoto, T.; Ishikawa, S.; Kobayashi, C.

2000-01-01

The tetrode tube of SIEMENS RS2074SK is used for HIMAC DTL (Drift Tube Linac) 1.4 MW final amplifiers. We installed a bench-test system for this tube in 1999. This system can be used under low power operation with CW mainly for filament aging. This system consists of DC sources, drive-amplifier (5 kW transistor amplifier) and 3/4λ coaxial input and output circuits. We will also use this system to improve the DTL final amplifiers, for example to reduce the parasitic oscillation level. This paper describes status of this system. (author)

A standardized procedure for eddy-current testing of stainless steel, thin-walled nuclear fuel element cladding tubes

International Nuclear Information System (INIS)

Barat, P.; Raj, B.; Bhattacharya, D.K.

1982-01-01

Thin-walled nuclear fuel cladding tubes made of AISI 316 stainless steel have been examined by eddy-current testing. Standardization of the procedures has required investigations on optimizing the test frequency, finding a method to locate a defect with respect to the probe reference end, and the use of standard defects and sequential metallography of natural defects detected by eddy-current testing, to understand the influence of the nature of defects on the impedance output signals. Test frequency and method of locating the defect were optimized by the use of standard defects made by machining in reference cladding tubes. Subsequent metallography of natural defects detected by eddy-current testing revealed mainly clusters of inclusions but also other types of defects. The effect of the distribution of inclusions along the length of the tube on the impedance output is discussed. (author)

Resuscitating the Baby after Shoulder Dystocia

Directory of Open Access Journals (Sweden)

Savas Menticoglou

2016-01-01

Full Text Available Background. To propose hypovolemic shock as a possible explanation for the failure to resuscitate some babies after shoulder dystocia and to suggest a change in clinical practice. Case Presentation. Two cases are presented in which severe shoulder dystocia was resolved within five minutes. Both babies were born without a heartbeat. Despite standard resuscitation by expert neonatologists, no heartbeat was obtained until volume resuscitation was started, at 25 minutes in the first case and 11 minutes in the second. After volume resuscitation circulation was restored, there was profound brain damage and the babies died. Conclusion. Unsuspected hypovolemic shock may explain some cases of failed resuscitation after shoulder dystocia. This may require a change in clinical practice. Rather than immediately clamping the cord after the baby is delivered, it is proposed that (1 the obstetrician delay cord clamping to allow autotransfusion of the baby from the placenta and (2 the neonatal resuscitators give volume much sooner.

EKSPLORASI HIJUAN PAKAN BABI DAN CARA PENGGUNAANNYA PADA PETERNAKAN BABI TRADISIONAL DI PROVINSI BALI

Directory of Open Access Journals (Sweden)

K. Budaarsa

2015-06-01

Full Text Available Penelitian ini bertujuan untuk mengetahui jenis-jenis hijauan yang diberikan sebagai pakan ternak babi dan cara penggunaannya di propvinsi Bali. Penelitian dilakukan dengan metode survei di seluruh kabupaten dan kota di Bali. Pengambilan sampel dilakukan dengan teknik stratified random sampling, dengan pengelompokan atas dataran rendah dan dataran tinggi di masing-masing kabupaten dan kota. Pada masing-masing kelompok di ambil 2 orang peternak babi tradisional, sehingga ada 4 peternak yang diwawancarai di masing-masing kabupaten dan kota atau 32 peternak di seluruh Bali. Hasil survei menunjukkan bahwa ada perbedaan hijauan yang diberikan oleh peternak di dataran rendah dan dataran tinggi. Jenis hijauan yang diberikan di dataran rendah antara lain: batang pisang (Musa paradisiaceae, kangkung (Ipomaea aquatica, biah-biah (Limnocharis flava, dan eceng gondok (Eichornia crassipes. Sedamgkan di dataran tinggi antara lain: batang pisang (Musa paradisiaceae, ketela rambat (Ipomaea batatas, daunt alas (Colocasia esculenta daun lamtoro (Leucaena leucocephala dan dag-dagse (Pisonia alba. Batang pisang dominan (95 % diberikan di dataran rendah maupun di dataran tinggi. Pemberian hijauan ada dengan cara direbus ada yang diberikan dalam bentuk segar. Kesimpulan dari penelitian ini adalah terdapat keragaman jenis hijauan pakan babi dan cara pemberiannya antara di dataran rendah dengan dataran tinggi di Bali. Batang pisang merupakan hijauan yang paling banyak digunakan untuk pakan babi pada peternakan babi tradisional, baik pada dataran rendah maupun dataran tinggi.

How Active Is Your Baby?

Science.gov (United States)

... range). As your baby develops, take advantage of every opportunity to help stimulate her mind and body. From the earliest weeks of life, walk around the house while holding and interacting with your baby and say aloud the names of the objects that the ...

Designer babies--why not?

Science.gov (United States)

Evans, M

2001-02-01

Though many objections can be levelled against the idea of the practice of genetic intervention to produce 'designer babies', upon examination they are shown to hinge on features which concern parental intentions towards their children, rather than features specific to the means involved. These intentions may be pursued by a variety of social practices which may, though need not, involve a measure of 'traditional' genetic selection (i.e. in terms of the identity and characteristics of the reproducing partners). This paper reviews a number of these objections and, by parity of reasoning, rejects their claim to count specifically or decisively against genetic intervention in pursuit of 'designer babies'. Rejecting these objections does not lead to the endorsement of 'designing babies, but it shows that any unease must be grounded elsewhere and defended by other arguments.

Preparing Your Family for a New Baby

Science.gov (United States)

... Shop AAP Find a Pediatrician Ages & Stages Prenatal Decisions to Make Delivery and Beyond Baby Toddler Preschool Gradeschool Teen ... preschooler in planning for the baby . This will make him less jealous. ... you get them ready for the new baby. Buy your child (boy or girl) a doll so ...

‘Baby Blues’ highbush blueberry

Science.gov (United States)

‘Baby Blues’ is a new highbush blueberry from the U.S. Department of Agriculture-Agricultural Research Service (USDA-ARS) breeding program in Corvallis, OR, released in cooperation with Oregon State University’s Agricultural Experiment Station. ‘Baby Blues’ is a vigorous, high-yielding, very small-f...

In-pile Creep Tests of Zircaloy Tubing in the Studsvik R2 Reactor. Final Report

International Nuclear Information System (INIS)

Tomani, Hans; Lindeloew, Ulf

2000-12-01

In this report are presented the findings of a prototype creep test on Zr4 guide tube specimens exposed in-pile and out-of-pile and stressed by constant bending moments. The calculated initial deflection curvature caused by the applied bending moment agrees very well with the measured initial values. Furthermore, the measurement results show excellent consistency. The dominant impact of neutron irradiation is clearly demonstrated. After 3 cycles (∼1300 hours) the irradiation creep is 4 times as large as the thermal creep. This is the case at least when fresh tube material is used. Irradiation creep progresses steadily, but the creep rate is not quite constant during the 3 irradiation cycles. The thermal creep, on the other hand, quickly saturates and there is hardly any further deflection after the second cycle for the specimen situated above the core. A limitation with the rig has been that the tube deflection became limited by the rig carrier body of the rig in the neutron flux (core) that disqualified the results of a fourth irradiation cycle actually performed in the fall of 1998. The test method appears to be suitable for testing the bending creep of different guide tube materials or designs under PWR conditions

Cumulative damage fatigue tests on nuclear reactor Zircaloy-2 fuel tubes at room temperature and 3000C

International Nuclear Information System (INIS)

Pandarinathan, P.R.; Vasudevan, P.

1980-01-01

Cumulative damage fatigue tests were conducted on the Zircaloy-2 fuel tubes at room temperature and 300 0 C on the modified Moore type, four-point-loaded, deflection-controlled, rotating bending fatigue testing machine. The cumulative cycle ratio at fracture for the Zircaloy-2 fuel tubes was found to depend on the sequence of loading, stress history, number of cycles of application of the pre-stress and the test temperature. A Hi-Lo type fatigue loading was found to be very much damaging at room temperature and this feature was not observed in the tests at 300 0 C. Results indicate significant differences in damage interaction and damage propagation under cumulative damage tests at room temperature and at 300 0 C. Block-loading fatigue tests are suggested as the best method to determine the life-time of Zircaloy-2 fuel tubes under random fatigue loading during their service in the reactor. (orig.)

The Rourke Baby Record Infant/Child Maintenance Guide: do doctors use it, do they find it useful, and does using it improve their well-baby visit records?

Science.gov (United States)

Rourke, Leslie; Godwin, Marshall; Rourke, James; Pearce, Sarah; Bean, Joyce

2009-04-30

The Rourke Baby Record (RBR) - http://www.rourkebabyrecord.ca - is a freely available evidence-based structured form for child health surveillance from zero to five years. Family physicians/general practitioners (FP/GPs) doing office based well-baby care in three Ontario Canada cities (London, Ottawa, and Toronto) were randomly sampled to study the prevalence and utility of the RBR and documentation of well-baby visits. Database with telephone confirmation was conducted to assess the prevalence of use of the RBR. Study Part 1: Questionnaire mailed to a random sample of 100 RBR users. Outcome measures were utility of, helpfulness of, and suggestions for the RBR. Descriptive analysis was employed. Study Part 2: Retrospective chart review of well-baby visits by 38 FP/GPs using student t-tests and factor analysis. Outcome measures were well-baby visit documentation of growth, nutrition, safety issues, developmental milestones, physical examination, and overall comprehensiveness. The RBR was used by 78.5% (402/512) of successfully contacted FP/GPs who did well-baby care in these 3 cities. Study Part 1: Questionnaire respondents (N = 41/100) used the RBR in several ways, and found it most helpful for assessing healthy child development, charting/recording the visits, managing time effectively, addressing parent concerns, identifying health problems, and identifying high risk situations. The RBR was seen to be least helpful as a tool for managing or for referring identified health problems. Study Part 2: Charts from a total of 1,378 well-baby visits on 176 children were audited. Well-baby care provided by the 20 FP/GPs who used the RBR compared to that by the 18 non-users was statistically more likely to include documentation of type of feeding (p = 0.023), discussion of safety issues (p baby care provided by the RBR users compared to that by the non-users was not more likely to include documentation of measurement of growth (p = 0.097), or physical examination (p = 0

Heat Exchanger Tube to Tube Sheet Joints Corrosion Behavior

Directory of Open Access Journals (Sweden)

M. Iancu

2013-03-01

Full Text Available Paper presents the studies made by the authors above the tube to tube sheet fittings of heat exchanger with fixed covers from hydrofining oil reforming unit. Tube fittings are critical zones for heat exchangers failures. On a device made from material tube and tube sheet at real joints dimensions were establish axial compression force and traction force at which tube is extracted from expanded joint. Were used two shapes joints with two types of fittings surfaces, one with smooth hole of tube sheet and other in which on boring surface we made a groove. From extracted expanded tube zones were made samples for corrosion tests in order to establish the corrosion rate, corrosion potential and corrosion current in working mediums such as hydrofining oil and industrial water at different temperatures. The corrosion rate values and the temperature influence are important to evaluate joints durability and also the results obtained shows that the boring tube sheet shape with a groove on hole tube shape presents a better corrosion behavior then the shape with smooth hole tube sheet.

Round robin tests of the PISC III programme on defective steam generators tubes

International Nuclear Information System (INIS)

Birac, C.; Herkenrath, H.; Crutzen, S.; Miyake, Y.; Maciga, G.

1991-11-01

The PISC III actions are intended to extend the results and methodologies of the previous PISC exercises, i.e. the assessment of the capabilities of the various examination techniques when used on real or realistic flaws in real components under real conditions of inspection. Being aware of the industrial problems that the degradation of steam generator tubes can create, the PISC III management board decided to include in the PISC III programme a special action on steam generator tubes testing (SGT). (author)

Testing Placement of Gastric Feeding Tubes in Infants.

Science.gov (United States)

Metheny, Norma A; Pawluszka, Ann; Lulic, Melanie; Hinyard, Leslie J; Meert, Kathleen L

2017-11-01

Inadvertent positioning of a nasogastric tube in the lung can cause serious complications, so identifying methods to detect improperly inserted tubes is imperative. To compare the sensitivity, specificity, and negative and positive predictive values of 4 pH cut points (< 4.0, < 4.5, < 5.0, and < 5.5) in differentiating gastric and tracheal aspirates under various treatment conditions and to explore the utility of a pepsin assay for distinguishing between gastric and tracheal aspirates. Gastric and tracheal aspirates were collected from critically ill infants undergoing mechanical ventilation who had nasogastric or orogastric feeding tubes. Aspirates were tested with colorimetric pH indicators and a rapid pepsin assay. Information about treatment conditions was obtained from medical records. Two hundred twelve gastric aspirates and 60 tracheal aspirates were collected from 212 patients. Sensitivity was highest and specificity was lowest at the gastric aspirate pH cut point of less than 5.5. Positive predictive values were 100% at all pH cut points less than 5.0. Negative predictive values were higher at the pH cut point of less than 5.0 than at cut points less than 4.5. A higher percentage of pepsin-positive readings was found in gastric aspirates (88.3%) than in tracheal aspirates (5.4%). For a desired positive predictive value of 100%, a pH cut point of less than 5.0 provides the best negative predictive values, regardless of gastric acid inhibitor administration and feeding status. The pepsin assay is promising as an additional marker to distinguish gastric from tracheal aspirates. ©2017 American Association of Critical-Care Nurses.

Circumferential tensile test method for mechanical property evaluation of SiC/SiC tube

Energy Technology Data Exchange (ETDEWEB)

Yu, Ju-Hyeon, E-mail: 15096018@mmm.muroran-it.ac.jp [Graduate School, Muroran Institute of Technology, 27-1, Muroran, Hokkaido (Japan); Kishimoto, Hirotatsu [Graduate School, Muroran Institute of Technology, 27-1, Muroran, Hokkaido (Japan); OASIS, Muroran Institute of Technology, 27-1, Muroran, Hokkaido (Japan); Park, Joon-soo [OASIS, Muroran Institute of Technology, 27-1, Muroran, Hokkaido (Japan); Nakazato, Naofumi [Graduate School, Muroran Institute of Technology, 27-1, Muroran, Hokkaido (Japan); Kohyama, Akira [OASIS, Muroran Institute of Technology, 27-1, Muroran, Hokkaido (Japan)

2016-11-01

Highlights: • NITE SiC/SiC cooling channel system to be a candidate of divertor system in future. • Hoop strength is one of the important factors for a tube. • This research studies the relationship between deformation and strain of SiC/SiC tube. - Abstract: SiC fiber reinforced/SiC matrix (SiC/SiC) composite is expected to be a candidate material for the first-wall, components in the blanket and divertor of fusion reactors in future. In such components, SiC/SiC composites need to be formed to be various shapes. SiC/SiC tubes has been expected to be employed for blanket and divertor after DEMO reactor, but there is not established mechanical investigation technique. Recent progress of SiC/SiC processing techniques is likely to realize strong, having gas tightness SiC/SiC tubes which will contribute for the development of fusion reactors. This research studies the relationship between deformation and strain of SiC/SiC tube using a circumferential tensile test method to establish a mechanical property investigation method of SiC/SiC tubes.

Colostrum: Your Baby's First Meal

Science.gov (United States)

... Our Sponsors Ages & Stages Ages & Stages Ages and Stages Prenatal Baby (0-12 mos.) Toddler 1-3yrs. Preschool 3-5yrs Grade School 5-12yrs. Teen 12- ... the Word Shop AAP Find a Pediatrician Ages & Stages Prenatal Baby Bathing & Skin ... Teen Young Adult Healthy Children > Ages & Stages > ...

A report from America: Baby M.

Science.gov (United States)

Rachels, James

1987-10-01

Rachels reviews the social and legal facts of the celebrated "Baby M" case, in which surrogate Mary Beth Whitehead attempted to keep the daughter she had borne under contract to William Stern. The first phase of the legal battle between the parents ended in March 1988, when New Jersey Superior Court Judge Harvey R. Sorkow upheld the validity of the surrogacy contract, terminated Whitehead's parental rights, and awarded custody of the child to Stern. Rachels comments on public reaction to "Baby M," on Sorkow's decision, and on the impact the case may have on legislative attempts to regulate surrogacy. He also uses the example of "Baby M," as well as that of California heart transplant patient "Baby Jesse," to discuss how the media sensationalize controversial issues.

Preliminary studies of microchannel plate photomultiplier tube neutron detectors for flight test applications

International Nuclear Information System (INIS)

Dolan, K.W.

1978-10-01

Electrical, mechanical, thermal, and neutron response data indicate that microchannel plate photomultiplier tubes are viable candidates as miniature, ruggedized neutron detectors for flight test applications in future weapon systems

Baby-Friendly Practices Minimize Newborn Infants Weight Loss.

Science.gov (United States)

Procaccini, Diane; Curley, Ann L Cupp; Goldman, Martha

2018-04-01

It is accepted that newborns lose weight in the first few days of life. Baby-Friendly practices that support breastfeeding may affect newborn weight loss. The objective of this study were: 1) To determine whether Baby-Friendly practices are associated with term newborn weight loss day 0-2 in three feeding categories (exclusively breastfed, mixed formula fed and breastfed, and formula fed). 2) To determine whether Baby-Friendly practices increase exclusive breast feeding rates in different ethnic populations. This was a retrospective case-control study. Term newborn birth weight, neonatal weights days 0-2, feeding type, type of birth, and demographic information were collected for 1,000 births for the year before Baby-Friendly designation (2010) and 1,000 in 2013 (after designation). Ultimately 683 in the first group and 518 in the second met the inclusion criteria. Mean weight loss decreased day 0-2 for infants in all feeding types after the initiation of Baby-Friendly practices. There was a statistically significant effect of Baby-Friendly designation on weight loss for day 0-2 in exclusively breastfed infants (p Baby-Friendly practices were put in place. There was a decrease in mean weight loss day 0-2 regardless of feeding type after Baby-Friendly designation. Exclusive breast feeding increased in the presence of Baby-Friendly practices.

Status report for the Neutrino Platform NP05 (Baby MIND) experiment

CERN Document Server

Noah, E

2016-01-01

Report outlining progress by the Baby MIND collaboration since the October 2015 SPSC committee meeting. The Baby-MIND proposal was approved as NP05 with a clear recommendation to focus the project on the timely delivery of the magnetized downstream muon spectrometer for the Wagasci project. The measures taken to fullfill these recommendations are summarized. The status of the magnet design and procurement; of the detector modules, procurement of scintillator and module mechanics design; the status of the electronics and DAQ; and finally simulations and analysis are desctribed. The project schedule and milestones, the plans for test beam and the request for the use of the T9 test area are presented.

Baby universes, fine tuning problems

International Nuclear Information System (INIS)

Nielsen, H.B.; Ninomiya, Masao.

1988-12-01

We review the recently popular 'theory of baby universes' put forward by Banks, Coleman and Hawking. We then derive the strong CP breaking coefficient θ-bar to be very small, in a similar manner to the derivation of the cosmological constant being zero. A solution for an old controversy concerning the entropy creation in black holes is also discussed. We finally confront the baby universe theory with random dynamics. We conclude that the theory of baby universes is so successful that the essential features are likely true and might have to go into a right theory even if with some troubles at first. (author)

Baby factories taint surrogacy in Nigeria.

Science.gov (United States)

Makinde, Olusesan Ayodeji; Makinde, Olufunmbi Olukemi; Olaleye, Olalekan; Brown, Brandon; Odimegwu, Clifford O

2016-01-01

The practice of reproductive medicine in Nigeria is facing new challenges with the proliferation of 'baby factories'. Baby factories are buildings, hospitals or orphanages that have been converted into places for young girls and women to give birth to children for sale on the black market, often to infertile couples, or into trafficking rings. This practice illegally provides outcomes (children) similar to surrogacy. While surrogacy has not been well accepted in this environment, the proliferation of baby factories further threatens its acceptance. The involvement of medical and allied health workers in the operation of baby factories raises ethical concerns. The lack of a properly defined legal framework and code of practice for surrogacy makes it difficult to prosecute baby factory owners, especially when they are health workers claiming to be providing services to clients. In this environment, surrogacy and other assisted reproductive techniques urgently require regulation in order to define when ethico-legal lines have been crossed in providing surrogacy or surrogacy-like services. Copyright © 2015 Reproductive Healthcare Ltd. Published by Elsevier Ltd. All rights reserved.

Baby universes with induced gravity

International Nuclear Information System (INIS)

Gao Yihong; Gao Hongbo

1989-01-01

In this paper some quantum effects of baby universes with induced gravity are discussed. It is proved that the interactions between the baby-parent universes are non-local, and argue that the induced low-energy cosmological constant is zero. This argument does not depend on the detail of the induced potential

Baby boomers nearing retirement: the healthiest generation?

Science.gov (United States)

Rice, Neil E; Lang, Iain A; Henley, William; Melzer, David

2010-02-01

The baby-boom generation is entering retirement. Having experienced unprecedented prosperity and improved medical technology, they should be the healthiest generation ever. We compared prevalence of disease and risk factors at ages 50-61 years in baby boomers with the preceding generation and attributed differences to period or cohort effects. Data were from the Health Survey for England (HSE) from 1994 to 2007 (n = 48,563). Logistic regression models compared health status between birth cohorts. Age-period-cohort models identified cohort and period effects separately. Compared to the wartime generation, the baby-boomer group was heavier (3.02 kg; 95% confidence interval [CI], 2.42-3.63; p Baby boomers reported fewer heart attacks (OR = 0.61; CI, 0.47-0.79; p baby boomers are moving toward retirement with improved cardiovascular health. However, the baby-boomer cohort has a higher prevalence of mental illness diagnoses and shows no improvement in self-rated health compared to the wartime birth cohort. There remains substantial scope to reduce health risks and future disability.

The Aphrodite boiling crisis program. Analysis of CHF tests performed on a vertical tube

International Nuclear Information System (INIS)

Souyri, A.; Conan, S.; Portesse, A.; Tremblay, D.

1992-09-01

In order to develop a comprehensive modelling of the boiling crisis phenomenon, the APHRODITE experimental program has been set up at ELECTRICITE DE FRANCE. Aiming at a better mechanistic understanding of this phenomenon, this program will investigate the influence of the experimental conditions (among which the mockup geometry and the boundary conditions) and the two-phase flow patterns via void fraction distributions. It has involved the construction of a R12 test loop, which can deliver a large thermal-hydraulic parameter ranges, and the development of a gamma-ray tomograph. The first experiments have been carried out on a vertical Inconel tube, 6 meters long with a bore diameter of 13 mm and a thickness of 0.5 mm. This electrically heated test section is heavily instrumented with 168 thermocouples welded along the tube, on its outer surface. After a refined calibration of the experimental procedure, a critical heat flux data bank has been collected within large pressure, mass velocity and critical steam quality ranges. These results are firstly compared with other CHF data obtained in similar conditions. Then several empirical correlations and a theoretical model for similar prediction in tubes are tested against these data

Test plan for Fauske and Associates to perform tube propagation experiments with simulated Hanford tank wastes

International Nuclear Information System (INIS)

Carlson, C.D.; Babad, H.

1996-05-01

This test plan, prepared at Pacific Northwest National Laboratory for Westinghouse Hanford Company, provides guidance for performing tube propagation experiments on simulated Hanford tank wastes and on actual tank waste samples. Simulant compositions are defined and an experimental logic tree is provided for Fauske and Associates (FAI) to perform the experiments. From this guidance, methods and equipment for small-scale tube propagation experiments to be performed at the Hanford Site on actual tank samples will be developed. Propagation behavior of wastes will directly support the safety analysis (SARR) for the organic tanks. Tube propagation may be the definitive tool for determining the relative reactivity of the wastes contained in the Hanford tanks. FAI have performed tube propagation studies previously on simple two- and three-component surrogate mixtures. The simulant defined in this test plan more closely represents actual tank composition. Data will be used to support preparation of criteria for determining the relative safety of the organic bearing wastes

Implementing the Fussy Baby Network[R] Approach

Science.gov (United States)

Gilkerson, Linda; Hofherr, Jennifer; Heffron, Mary Claire; Sims, Jennifer Murphy; Jalowiec, Barbara; Bromberg, Stacey R.; Paul, Jennifer J.

2012-01-01

Erikson Institute Fussy Baby Network[R] (FBN) developed an approach to engaging parents around their urgent concerns about their baby's crying, sleeping, or feeding in a way which builds their longer-term capacities as parents. This approach, called the FAN, is now in place in new Fussy Baby Network programs around the country and is being infused…

A cryogenic tensile testing apparatus for micro-samples cooled by miniature pulse tube cryocooler

International Nuclear Information System (INIS)

Chen, L B; Liu, S X; Gu, K X; Zhou, Y; Wang, J J

2015-01-01

This paper introduces a cryogenic tensile testing apparatus for micro-samples cooled by a miniature pulse tube cryocooler. At present, tensile tests are widely applied to measure the mechanical properties of materials; most of the cryogenic tensile testing apparatus are designed for samples with standard sizes, while for non-standard size samples, especially for microsamples, the tensile testing cannot be conducted. The general approach to cool down the specimens for tensile testing is by using of liquid nitrogen or liquid helium, which is not convenient: it is difficult to keep the temperature of the specimens at an arbitrary set point precisely, besides, in some occasions, liquid nitrogen, especially liquid helium, is not easily available. To overcome these limitations, a cryogenic tensile testing apparatus cooled by a high frequency pulse tube cryocooler has been designed, built and tested. The operating temperatures of the developed tensile testing apparatus cover from 20 K to room temperature with a controlling precision of ±10 mK. The apparatus configurations, the methods of operation and some cooling performance will be described in this paper. (paper)

Improvement in reliability and accuracy of heater tube eddy current testing by integration with an appropriate destructive test

International Nuclear Information System (INIS)

Giovanelli, F.; Gabiccini, S.; Tarli, R.; Motta, P.

1988-01-01

A specially developed destructive test is described showing how the reliability and accuracy of a non-destructive technique can be improved if it is suitably accompanied by an appropriate destructive test. The experiment was carried out on samples of AISI 304L tubes from the low-pressure (LP) preheaters of a BWR 900 MW nuclear plant. (author)

Crack growth of throughwall flaw in Alloy 600 tube during leak testing

International Nuclear Information System (INIS)

Bahn, Chi Bum; Majumdar, Saurin

2015-01-01

Graphical abstract: - Highlights: • A series of leak testing was conducted at a constant pressure and room temperature. • The time-dependent increase in the leak rate was observed. • The fractography revealed slip offsets and crystallographic facets. • Time-dependent plasticity at the crack tip caused the slip offsets. • Fatigue by jet/structure interaction caused the crystallographic facets. - Abstract: We examined the issue of whether crack growth in a full thickness material can occur in a leaking crack. A series of leak tests was conducted at a room temperature and constant pressure (17.3 MPa) with Alloy 600 tube specimens containing a tight rectangular throughwall axial fatigue crack. To exclude a potential pulsation effect by a high pressure pump, the test water was pressurized by using high pressure nitrogen gas. Fractography showed that crack growth in the full thickness material can occur in the leaking crack by two mechanisms: time-dependent plasticity at the crack tip and fatigue induced by jet/structure interaction. The threshold leak rate at which the jet/structure interaction was triggered was between 1.3 and 3.3 L/min for the specific heat of the Alloy 600 tube tested

Opinion and knowledge among hospital medical staff regarding diagnosis of diabetes and proper usage of a specific test tube for glucose analysis.

Science.gov (United States)

Bar-Dayan, Y; Bogaiov, A; Boaz, M; Landau, Z; Wainstein, J

2014-02-01

Accuracy of blood sugar values, as examined by glucose analysis, has significant importance on the diagnosis of diabetes and follow up of diabetes treatment. Usage of a designated test tube significantly improves the accuracy of measurement. Knowledge of the medical staff is a major determinant in the current usage of such a technology. The aim of the study was to assess the level of knowledge exhibited by medical staff in the diabetes field and specifically for the usage of a designated tube to test blood glucose level. A prospective study. The staff of the internal and surgical departments and outpatient clinics at the Wolfson Medical Center completed a questionnaire that assessed the level of knowledge about the designated glucose test tube, other randomly used test tubes, the parameters that influence the blood glucose values in a non-designated tube and the diagnosis of diabetes. A number of 160 questionnaires (50% from internal departments, 36% from surgical departments and 14% from outpatient clinics) were analysed. The majority of the staff members (65%) knew that diabetes is diagnosed by glucose levels in blood. Of the 35% that did not know, 91% were nurses. The majority (75%) knew that diabetes is diagnosed during fasting conditions; however, most of the staff indicated that 12 h is needed. Only 25% knew of the designated test tube, and most of the staff indicated that a regular chemistry tube was the tube of choice for them. The staff exhibited poor level of knowledge regarding the parameters that influence the quality of the test. Staff members are not aware of the various aspects of diabetes diagnosis and the designated test tube for glucose measurements, and most of them use a tube that gives inaccurate measurements, therefore there is an urgent need to improve diabetes knowledge among staff members. © 2013 John Wiley & Sons Ltd.

Test and evaluation of the BBC CQK 200-4 modulator tube for the MFTF sustaining neutral beam power supply system

International Nuclear Information System (INIS)

Eckard, R.D.; Van Ness, H.W.; Hesselgrave, D.

1979-01-01

The BBC CQK 200-4 Tube was tested by Aydin at LLL, to confirm that it would switch 90 kV after conducting 88 amperes for 30 seconds. The CQK 200-4 is a recent modification of the CQK 200-3, an Rf transmitter tube designed for continuous loading, to increase the anode hold-off voltage to 150 kV. During the design life of the tube it will be subjected to 10 5 to 10 6 cyclic thermal loads. Two concerns are that (1) during the 30 second high current load, the screen grid may have excessive dissipation causing a loss of control of the tube, and (2) the cyclic temperature-induced stresses in the anode may cause fatigue failures that will reduce the tube's useful life. The first concern was addressed by performing full scale tests at the LLL test facility

Mermaid baby

Directory of Open Access Journals (Sweden)

N Khan

2010-08-01

Full Text Available We were recently intrigued by a baby born at Kalafong Hospital with fused lower extremities resembling a mermaid, which caused us to search for the background and origin of this entity called sirenomelia.

Assessment of CCFL model of RELAP5/MOD3 against simple vertical tubes and rod bundle tests

International Nuclear Information System (INIS)

Cho, Sung Jae; Arne, Nam Sung; Chung, Bub Dong; Kim, Hho Jung

1991-01-01

The CCFL model used in RELAP5/MOD3 version 5m5 has been assessed against simple vertical tubes and rod bundle tests performed at a facility of Korea Atomic Energy Research Institute. The effect of changes in tube diameter and nodalization of tube section were investigated. The roles of interfacial drags on the flooding characteristics are discussed. Difference between the calculation and the experiment are also discussed. A comparison between model assessment results and the test data showed that the calculated value lay well on the experimental flooding curve specified by user, but the pressure jump before onset of flooding was not calculated

Applied research for profilometric testing of the state of interior surfaces in heat exchanger tubes

International Nuclear Information System (INIS)

Gyongyosi, Tiberiu; Panaitescu, Valeriu Nicolae

2009-01-01

Generally, the surface flaws identified at heat exchangers tubing are characteristic for the heat secondary systems, located on the external surfaces of the heat exchanger tubes and are mostly the results of the ageing phenomena in systems operation. The tests performed, with the impressing replicating device confirmed the applicability of the technique, functionality of the device and resulted in replicas on metal support, these being the hard copy of the negative of the test tube surface, allowing the profile measurement. The visual inspection of the replicas on the metallic support gives information about the surface geometry replicated, pointing out the marks, which belong to the same area under observation. The minimum and maximum values for the depth of the channel worked out in the inner test tube wall have been determined by profile graphic measurement on the replicas. The paper presents the structural and functional description of the experimental devices. The first results and some conclusions are also included. Two patent applications were submitted at State Office for Inventions and Trademarks (OSIM) covering the original data to protect royalty: 'The local pit flaws, scratches, incipient micro-cracks replicating device on inner cylindrical surfaces', under no. A/00299/17.04.2008 and 'The annular local flaw, incipient micro-cracks replicating device on inner cylindrical surface' under no. A/00300/17.04.2008

Signal Characteristics of Eddy Current Test for Intergranular Attack of Steam Generator Tubes

International Nuclear Information System (INIS)

Choi, Myung Sik; Lee, Deok Hyun; Han, Jung Ho; Hur, Do Haeng; Cho, Se Gon; Yim, Chang Jae

2002-01-01

Because intergranular attack (IGA), one of the localized corrosion forms occurring on steam generator tubes, can not be fabricated by an electric discharge machining method, there are few data for the eddy current test (ECT) characteristics of IGA. In this paper, the characteristics of eddy current signals are evaluated using nonexpanded tubes with IGA defects formed in 0.1 M sodium tetrathionate solution at 40 .deg. C. The detectability and sizing accuracy of IGA were discussed in terms of the coil type and frequency of the ECT probes

Recent Advances in Simulation of Eddy Current Testing of Tubes and Experimental Validations

Science.gov (United States)

Reboud, C.; Prémel, D.; Lesselier, D.; Bisiaux, B.

2007-03-01

Eddy current testing (ECT) is widely used in iron and steel industry for the inspection of tubes during manufacturing. A collaboration between CEA and the Vallourec Research Center led to the development of new numerical functionalities dedicated to the simulation of ECT of non-magnetic tubes by external probes. The achievement of experimental validations led us to the integration of these models into the CIVA platform. Modeling approach and validation results are discussed here. A new numerical scheme is also proposed in order to improve the accuracy of the model.

Assessment of thin-walled cladding tube mechanical properties by segmented expanding Mandrel test

International Nuclear Information System (INIS)

Nilsson, Karl-Fredrik

2015-01-01

This paper presents the principles of the segmented expanding mandrel test for thin-walled cladding tubes, which can be used as a basic material characterisation test to determine stress-strain curves and ductility or as a test to simulate mechanical pellet-cladding interaction. The paper discusses the strengths and weaknesses of the test method and it illustrates how the test can be used to simulate hydride reorientations in zirconium claddings and quantify how hydride reorientation affects ductility. (authors)

QuantiFERON–TB Gold In-Tube test performance in Denmark

DEFF Research Database (Denmark)

Hermansen, Thomas; Lillebaek, Troels; Hansen, Ann-Brit E

2014-01-01

BACKGROUND: Little is known about the QuantiFERON-TB Gold In-Tube Test (QFT) in extreme age groups. The test performance has been reported to be impaired in children and elderly, but reports are diverging. The aim of this study was to evaluate QFT performance in patients with and without......, the overall QFT performance was good. The sensitivity in children (≥ 1) was high although few children were included, whereas sensitivity declined with increasing age. Indeterminate rates were higher in infants and elderly. In contrast to current guidelines, our data suggest that the QFT performs well...... in children ≥ 1 years in low endemic regions but that the test should be used with care among the elderly....

Effect of tubing condensate on non-invasive positive pressure ventilators tested under simulated clinical conditions.

Science.gov (United States)

Hart, Diana Elizabeth; Forman, Mark; Veale, Andrew G

2011-09-01

Water condensate in the humidifier tubing can affect bi-level ventilation by narrowing tube diameter and increasing airflow resistance. We investigated room temperature and tubing type as ways to reduce condensate and its effect on bi-level triggering and pressure delivery. In this bench study, the aim was to test the hypothesis that a relationship exists between room temperature and tubing condensate. Using a patient simulator, a Res-med bi-level device was set to 18/8 cm H(2)O and run for 6 h at room temperatures of 16°C, 18°C and 20°C. The built-in humidifier was set to a low, medium or high setting while using unheated or insulated tubing or replaced with a humidifier using heated tubing. Humidifier output, condensate, mask pressure and triggering delay of the bi-level were measured at 1 and 6 h using an infrared hygrometer, metric weights, Honeywell pressure transducer and TSI pneumotach. When humidity output exceeded 17.5 mg H(2)O/L, inspiratory pressure fell by 2-15 cm H(2)O and triggering was delayed by 0.2-0.9 s. Heating the tubing avoided any such ventilatory effect whereas warmer room temperatures or insulating the tubing were of marginal benefit. Users of bi-level ventilators need to be aware of this problem and its solution. Bi-level humidifier tubing may need to be heated to ensure correct humidification, pressure delivery and triggering.

Relationship between maternal periodontal disease and low birth weight babies

Directory of Open Access Journals (Sweden)

Ahmad Haerian-Ardakani

2013-01-01

Full Text Available Background: Periodontal infections, which serve as a reservoir of inflammatory mediators, may pose a threat to the fetal-placental unit and cause adverse pregnancy outcomes. Objective: The aim of this study was assessing the periodontal status of women during puerperium and determining the possible relationship between their periodontal disease and low birth weight delivery. Materials and Methods: This was a case-control study. The sample included 88 ex-pregnant women were seen at maternity hospitals of Yazd, Iran. Half of the mothers had low birth babies (LBW (birth weight below 2500g- case group and the others had normal weight babies (>2500g- control group. The mothers’ data were obtained from medical files, interview and periodontal clinical examination carried out up to 3 days after delivery. Bleeding on probing, presence of supra-gingival calculus and CPITN (Community Periodontal Index for Treatment Needs were used for periodontal assessment Results: Among the known risk factors of LBW babies, history of previous LBW infant among case mothers reached statistical significance (p=0.0081, Student t-test. Mothers of LBW infants had less healthy areas of gingiva (p=0.042, and more deep pockets (p=0.0006, Mann-Whitney test. Conclusion: The maternal periodontal disease can be a potential independent risk factor for LBW.

Baby Factory

African Journals Online (AJOL)

Prof

2018-01-24

Jan 24, 2018 ... mass media have the power to easily propagate ideas on social change ... issue of 'baby factory' is becoming everyday news affecting the right of ... according to recent mass media reports, teenage girls and young women are.

Fluid-Elastic Instability Tests on Parallel Triangular Tube Bundles with Different Mass Ratio Values under Increasing and Decreasing Flow Velocities

Directory of Open Access Journals (Sweden)

Xu Zhang

2016-01-01

Full Text Available To study the effects of increasing and decreasing flow velocities on the fluid-elastic instability of tube bundles, the responses of an elastically mounted tube in a rigid parallel triangular tube bundle with a pitch-to-diameter ratio of 1.67 were tested in a water tunnel subjected to crossflow. Aluminum and stainless steel tubes were tested, respectively. In the in-line and transverse directions, the amplitudes, power spectrum density functions, response frequencies, added mass coefficients, and other results were obtained and compared. Results show that the nonlinear hysteresis phenomenon occurred in both tube bundle vibrations. When the flow velocity is decreasing, the tubes which have been in the state of fluid-elastic instability can keep on this state for a certain flow velocity range. During this process, the response frequencies of the tubes will decrease. Furthermore, the response frequencies of the aluminum tube can decrease much more than those of the stainless steel tube. The fluid-elastic instability constants fitted for these experiments were obtained from experimental data. A deeper insight into the fluid-elastic instability of tube bundles was also obtained by synthesizing the results. This study is beneficial for designing and operating equipment with tube bundles inside, as well as for further research on the fluid-elastic instability of tube bundles.

Safe Sleep for Babies PSA (:60)

Centers for Disease Control (CDC) Podcasts

This 60 second public service announcement is based on the January 2018 CDC Vital Signs report. Every year, there are about 3,500 sleep-related deaths among U.S. babies. Learn how to create a safe sleep environment for babies.

Reducing the risk of baby falls in maternity units.

Science.gov (United States)

Janiszewski, Helen

During a 12-month period there were 17 baby falls on the maternity wards at Nottingham University Hospitals Trust; two of the babies who fell were injured. By collecting information about the baby falls and how they happened, we were able to compile a guideline for both preventing and managing baby falls. This formed part of the trust's patient safety programme. We then piloted and implemented risk-prevention strategies for baby falls. These involved a risk assessment to identify women needing closer observation and the installation of bedside cots. These strategies brought about a marked reduction of baby falls and are now being established across all the maternity units across the trust.

Development of the double-wall-tube steam generator. Evaluation of inner tube leak detection system

International Nuclear Information System (INIS)

Teraoku, Takuji; Kisohara, Naoyuki

1995-01-01

A double-wall-tube steam generator (DWT-SG) is considered to have possibility of eliminating a secondary heat transport system to realize a reliable and simplified FBR plant. Thus, basic tests for inner/outer tube leak detection and prototypical leak tests by use of the 1MWt DWT-SG model have been performed to evaluate the feasibility of DWT-SG. Their results demonstrated that the inner leak detection system can definitely detect a steam leak from an inner tube flaw. Analyses of the inner tube leak and detection behavior obtained in the 1MWt DWT-SG test enabled to estimate the performance of the inner tube detection system of the commercial DWT-SG system. (author)

Demonstration test of the spent fuel rod cutting process with tube cutter mechanism

International Nuclear Information System (INIS)

Lee, Jong Youl; Jung, Jae Hoo; Hong, Dong Hee; Yoon, Ji Sup; Lee, Eun Pyo

2001-03-01

In this paper, the verification by computer graphics technology for the spent fuel rod cutting devise which belongs to the spent fuel disassembly processes, the performance tests of the real device, and the demonstration tests with tube cutter mechanism are described. The graphical design system is used throughout the design stages from conceptual design to motion analysis like collision detection. By using this system, the device and the process are optimized. The performance test of the real device and the demonstration test using the tube cutter mechanism in the hot cell are carried out. From these results, the spent fuel rod cutting device is improved based on the considerations of circularity of the rod cross-section, debris generation, and fire risk etc. Also, this device is improved to be operated automatically via remote control system considering later use in closed environment like Hot-cell (radioactive area) and the modulization in the structure of this device makes maintenance easy. The result of the performance test and the demonstration in this report is expected to contribute to the optimization of the pre-treatment processes for the reuse of the spent fuel like DUPIC process and the final disposal

Iodine Contents in Baby Food Consumed in Japan

Directory of Open Access Journals (Sweden)

Yoshida M.

2013-04-01

Full Text Available To evaluate iodine intake in Japanese infants, iodine contents were determined in both commercial and homemade baby food samples consumed in Japan. Fifty-three samples of commercial bottled or retort baby food and 25 samples of homemade baby food for one day were collected and their iodine contents were determined by inductively coupled plasma mass spectrometry after an extraction with 0.5% tetramethylammonium hydroxide. Among the commercial baby food samples, 35 samples showed low iodine values ( 1000 ng/g wet weight. Significantly higher iodine values were observed in 15 samples composed of dishes cooked using kombu (a kind of kelp than other samples. Among the homemade baby food samples, 12 samples brought very low iodine intake (< 1- 24 μg/d, while 5 samples brought very high iodine intake (283-978 μg/d. These results indicate that intermittent high iodine baby food including dishes cooked using kombu contributes to sufficient iodine intake in Japanese infants.

Nondestructive testing of welds on thin-walled tubing

Science.gov (United States)

Hagemaier, D. J.; Posakony, G. J.

1969-01-01

Special ultrasonic search unit, or transducer assembly, reliably inspects the quality of melt-through welds of fusion welded tubing couplers for hydraulic lines. This instrumentation can also be used to detect faulty braze bonds in thin-walled, small diameter joints and wall thickness of thin-walled metal tubing.

VTR module: weaning foods for baby.

Science.gov (United States)

1993-01-01

Weaning should start when the baby turns 4 months old. At this stage (4 to 6 months), milk is no longer enough. Parents should introduce new foods which can meet the fast-increasing nutrition needs of the child. Among the latest materials produced by the Video Radio Production Division of the Nutrition Center of the Philippines is a VTR training module entitled "Karagdagang Pagkain ni Baby" (Weaning Foods for Baby), designed to strengthen this important aspect of child care. Specifically, the module seeks to encourage parents to introduce foods in addition to breastmilk to their 4 to 6 month old children and to start giving them "complete" meals from 6 months onward. It provides suggestions on the kinds of foods or food combinations to give to the baby and encourages home food production (backyard gardening, poultry-raising etc) to supply food requirements of growing children. Contents of the module include how-to's on weaning food preparation (mashing, straining, flaking, chopping, scraping, etc), prescriptions on the kinds and amounts of foods for babies; and food combinations (porridge or rice and a viand from the 3 basic food groups: energy-giving, body building and regulating). For instance, at 4 months old, the baby may be given lugao (porridge), soup and fruits; at 5 months, eggs, vegetables and beans; at 6 months, fish/meat, oil or gata (coconut oil). With a running time of 18 minutes, the module uses computer graphics to highlight food items, recommended amounts, and age group requirements in the text, and applies digital multi-effects to ensure smooth traditions. full text

Sick-visit immunizations and delayed well-baby visits.

Science.gov (United States)

Robison, Steve G

2013-07-01

Giving recommended immunizations during sick visits for minor and acute illness such as acute otitis media has long been an American Academy of Pediatrics/Advisory Committee on Immunization Practice recommendation. An addition to the American Academy of Pediatrics policy in 2010 advised considering whether giving immunizations at the sick visit would discourage making up missed well-baby visits. This study quantifies the potential tradeoff between sick-visit immunizations and well-baby visits. This study was a retrospective cohort analysis with a case-control component of sick visits for acute otitis media that supplanted normal well-baby visits at age 2, 4, or 6 months. Infants were stratified for sick-visit immunization, no sick-visit immunization but quick makeup well-baby visits, or no sick-visit immunizations or quick makeup visits. Immunization rates and well-baby visit rates were assessed through 24 months of age. For 1060 study cases, no significant difference was detected in immunization rates or well-baby visits through 24 months of age between those with or without sick-visit immunizations. Thirty-nine percent of infants without a sick-visit shot failed to return for a quick makeup well-baby visit; this delayed group was significantly less likely to be up-to-date for immunizations (relative risk: 0.66) and had fewer well-baby visits (mean: 3.8) from 2 through 24 months of age compared with those with sick-visit shots (mean: 4.7). The substantial risk that infants will not return for a timely makeup well-baby visit after a sick visit should be included in any consideration of whether to delay immunizations.

Learning and adherence to baby massage after two teaching strategies.

Science.gov (United States)

Cruz, Cláudia Marchetti; Caromano, Fátima Aparecida; Gonçalves, Lia Lopes; Machado, Thais Gaiad; Voos, Mariana Callil

2014-07-01

Little is known about learning/adherence after different baby massage teaching strategies. We compared the learning/adherence after two strategies. Twenty mothers from the group manual-course (GMC) and 20 from the group manual-orientations (GMO) received a booklet. GMC participated in a course during the third trimester. GMO received verbal instructions during the postpartum hospital stay. Multiple-choice and practical tests assessed learning (GMC: performing strokes on a doll; GMO: on the baby). Adherence was measured 3 months after childbirth. No differences were found between the groups in learning/adherence. Both teaching strategies showed similar and positive results. © 2014, Wiley Periodicals, Inc.

Failure analysis of glass-ceramic insulators of shock tested vacuum (neutron) tubes

International Nuclear Information System (INIS)

Spears, R.K.

1980-01-01

Eight investigative techniques were used to examine the glass-ceramic insulators in vacuum (neutron) tubes. The insulators were extracted from units that had been subjected to low temperature mechanical shock tests. Two of the three units showed reduced neutron output after these tests and an insulator on one of these two was cracked completely through which probably occurred during shock testing. The objective of this study was to determine if any major differences existed between the insulators of these tubes. After eight analyses, it was concluded that no appreciable differences existed. It appeared that cracking of the one glass-ceramic sample was initiated at inner-sleeve interface voids. For this sample, the interface void density was much higher than is presently acceptable. All insulators were made with glass-ceramic having a Na 2 O content of 4.6 wt%. An increased Na 2 O content will cause an increase in the coefficient of expansion and will reduce the residual stress level since the molybdenum has a higher coefficient of thermal expansion than the insulator. Thus, it is believed that a decrease in interface voids and an increase in Na 2 O should aid in reduced cracking of the insulator during these tests

Turning breech babies after 34 weeks: the if, how, & when of turning breech babies.

Science.gov (United States)

Cohain, Judy Slome

2007-01-01

Techniques for turning a term breech baby are 1). External cephalic version (ECV) using hands and ultrasound only; 2). Acupuncture point stimulation, by needle or moxibustion; 3). Chiropractic "Webster" technique; 4). Hypnotherapy; and 5). Special exercises. Fifty % of breech fetuses at 34 weeks will turn by themselves to head down by 38 weeks. Therefore, to be considered effective, a technique for turning breech must turn the baby and keep it turned more than 50% of the time. Only ECV with an experienced practitioner has been documented to have a greater than 50% success rate at 37 weeks; in 95% of cases the head stays down. Most women experience the fetus turning by hand as quick but very painful. "Unstable lie" is sometimes used as a baseless excuse for inducing labor after the baby turns from breech to head down. (judyslome@hotmail.com).

Tube-support response to tube-denting evaluation. Volume 1. Final report

International Nuclear Information System (INIS)

Anderson, P.L.; Hall, J.F.; Shah, P.K.; Wills, R.L.

1983-05-01

The response of the tube supports is one of the important considerations of tube denting in a steam generator. Investigations have indicated that damaged tube supports have the potential to distort and damage tubes. This investigation considers the response to tube denting of the Combustion Engineering type tube supports. Drilled support plates and eggcrate tube supports are tested in a model steam generator in which tube denting is induced. The experimental data is used to verify and refine analytical predictor models developed using finite element techniques. It was found that analytical models underpredicted the deformations of the tube supports and appropriate modifications to enhance the predictive capability are identified. Non-destructive examination methods are evaluated for application to operating steam generators. It was found that the standard eddy current and profilometry techniques are acceptable methods for determining tube deformations, but these techniques are not adequate to assess tube support damage. Radiography is judged to be the best available means of determining the extent and progression of damage in tube supports

A flow test for calibrating 177 core tubes of 1/5-scale reactor flow model for Yonggwang nuclear units 3 and 4

International Nuclear Information System (INIS)

Lee, Byung Jin; Jang, Ho Cheol; Cheong, Jong Sik; Kuh, Jung Eui

1990-01-01

A flow test was performed to find out the hydraulic characteristics of every one of 177 core tubes, representing a fuel assembly respectively, as a preparatory step of 1/5 scale reactor flow model test for Yonggwang Nuclear Units (hereafter YGN) 3 and 4. The axial hydraulic resistance of the fuel assembly was simulated in the square core tube with six orifice plates positioned along the tube length; core support structure below each fuel assembly was done in the core upstream geometry section of the test loop. For each core tube the pressure differentials across the inlet, exit orifice plate and overall tube length were measured, along with the flow rates and temperatures of the test fluid. The measured pressure drops were converted to pressure loss or flow metering coefficients. The metering coefficient of the inlet orifice plate was sensitive to the configuration and location of the upstream geometry. The hydraulic resistance of the core tubes were reasonably coincided with a target value and consistent. The polynomial curve fits of the calibrated coefficients for the 177 core tubes were obtained with reasonable data scatters

Experimental study of tube/support impact forces in multi-span PWR steam generator tubes

International Nuclear Information System (INIS)

Axisa, F.; Desseaux, A.; Gibert, R.J.

1984-12-01

The vibro-impact response of a straight part of a steam generator tube is investigated experimentally and using numerical simulation with the aim to relate tube overall dynamics with excitation and tube-support clearance. Configuration studied here corresponds to the tube being excited in only one direction at its first resonance presenting an antinode of vibration at the impacted support. Tests show namely that midspan displacement of tube is almost proportional to excitation level and clearance. Impact forces averaged over a cycle of vibration are almost proportional to excitation and poorly dependent on clearance. Results of numerical simulation are in fairly good agreement with test results

The baby boom, the baby bust, and the housing market.

Science.gov (United States)

Mankiw, N G; Weil, D N

1989-05-01

This paper explores the impact of demographic changes on the housing market in the US, 1st by reviewing the facts about the Baby Boom, 2nd by linking age and housing demand using census data for 1970 and 1980, 3rd by computing the effect of demand on price of housing and on the quantity of residential capital, and last by constructing a theoretical model to plot the predictability of the jump in demand caused by the Baby Boom. The Baby Boom in the U.S. lasted from 1946-1964, with a peak in 1957 when 4.3 million babies were born. In 1980 19.7% of the population were aged 20-30, compared to 13.3% in 1960. Demand for housing was modeled for a given household from census data, resulting in the finding that demand rises sharply at age 20-30, then declines after age 40 by 1% per year. Thus between 1970 and 1980 the real value of housing for an adult at any given age jumped 50%, while the real disposable personal income per capita rose 22%. The structure of demand is such that the swelling in the rate of growth in housing demand peaked in 1980, with a rate of 1.66% per year. Housing demand and real price of housing were highly correlated and inelastic. If this relationship holds in the future, the real price of housing should fall about 3% per year, or 47% by 2007. The theoretical model, a variation of the Poterba model, ignoring inflation and taxation, suggests that fluctuations in prices caused by changes in demand are not foreseen by the market, even though they are predictable in principle 20 years in advance. As the effects of falling housing prices become apparent, there may be a potential for economic instability, but people may be induced to save more because their homes will no longer provide the funds for retirement.

Method for shaping polyethylene tubing

Science.gov (United States)

Kramer, R. C.

1981-01-01

Method forms polyethylene plastic tubing into configurations previously only possible with metal tubing. By using polyethylene in place of copper or stain less steel tubing inlow pressure systems, fabrication costs are significantly reduced. Polyethylene tubing can be used whenever low pressure tubing is needed in oil operations, aircraft and space applications, powerplants, and testing laboratories.

A Study of Frequency Mixing Approaches for Eddy Current Testing of Steam Generator Tubes

International Nuclear Information System (INIS)

Jung, Hee Jun; Song, Sung Jin; Kim, Chang Hwan; Kim, Dae Kwang

2009-01-01

The multifrequency eddy current testing(ECT) have been proposed various frequency mixing algorithms. In this study, we compare these approaches to frequency mixing of ECT signals from steam generator tubes; time-domain optimization, discrete cosine transform-domain optimization. Specifically, in this study, two different frequency mixing algorithms, a time-domain optimization method and a discrete cosine transform(DCT) optimization method, are investigated using the experimental signals captured from the ASME standard tube. The DCT domain optimization method is computationally fast but produces larger amount of residue.

Feeding patterns and diet -- babies and infants

Science.gov (United States)

... child's state of development Can help prevent childhood obesity Recommendations During the first 6 months of life, your baby needs only breast milk or formula for proper nutrition. Your baby will ...

Tracking Your Baby's Weight and Measurements

Science.gov (United States)

... Our Sponsors Ages & Stages Ages & Stages Ages and Stages Prenatal Baby (0-12 mos.) Toddler 1-3yrs. Preschool 3-5yrs Grade School 5-12yrs. Teen 12- ... the Word Shop AAP Find a Pediatrician Ages & Stages Prenatal Baby Bathing & Skin ... Teen Young Adult Healthy Children > Ages & Stages > ...

Feeding Your Baby

Medline Plus

Full Text Available ... baby Formula feeding How to breastfeed Keeping breast milk safe and healthy Problems and discomforts when breastfeeding ... health & safety ') document.write('') } Ask our experts! Have a ...

DEMOGRAPHIC-ANAMNESTIC PARAMETERS WHICH AFFECT IMPLEMENTATION OF BABY FRIENDLY PROGRAM

Directory of Open Access Journals (Sweden)

Bozidar Jovanovic

2005-12-01

Full Text Available Various studies and extensive researches, particularly during recent years, on the advantages of breastfeeding and the use of breast milk in infant`s nourishment, have stressed its immeasurable benefit to mothers, infants, family and society. The objective of the research was to ascertain demographic and anamnestic factors affecting the implementation of the baby friendly program. The study was undertaken at OGC CC Kragujevac and based on data from 432 women. The mean age of the examinees was 25,9 years and they were 6 months younger than the corresponding examinees from similar world researches. In most cases, the examinees were from urban areas and lived in bigger families, which did not affect the implementation of the program. With equal probability, it was the first or second pregnancy and in most cases, there were no hospitalizations during the pregnancy in both tested groups. Medications are more often used during the implementation of the baby friendly program. The reason for positive influence of the use of medications during the pregnancy on implementation of the baby friendly program probably lies in better supervision of the pregnancy. The gestation age did not influence the selection into the program. By means of higher level of supervision and by the use of medications during pregnancy, we can positively influence mother`s and infant`s starting with the baby friendly programme implementation.

LAMELLAR ICHTHYOSIS (COLLODION BABY

Directory of Open Access Journals (Sweden)

Paramarta IGE

2012-11-01

Full Text Available The ichthyosis are a heterogeneous group of hereditary and acquired disorder of keratinization which affected the epidermis characterized by presence of visible scales on the skin surface in the absence of inflammation. It can occur as a disease limited to the skin or in association with abnormalities of other organ systems. Lamelar ihthyosis (LI is one of two mayor autosomal recessive ichthyosis with an incidence of approximately one in 300,000. The diagnosis is based on clinical and pathologic finding. Infection is the most common complication, while prognosis of LI is depends on severity and complication of the disease. A case of lamellar ichthyosis in 0 day Balinese female baby was reported. The skin of the body was thick, plate-like appearance, scaling on the entire body, some of the thick skin was ruptured on chest and extremities. There were eclabium on the mouth and ectropion on the eyes. Histopathology examination showed hyperkeratosis without perivascular infiltration lymphocyte. The baby was given breast feeding, antibiotic, hydrocortisone cream and olium olivarum. The prognosis of the baby is good.

The sky blue method as a screening test to detect misplacement of percutaneous endoscopic gastrostomy tube at exchange.

Science.gov (United States)

Suzuki, Yutaka; Urashima, Mitsuyoshi; Yoshida, Hideki; Iwase, Tsuyoshi; Kura, Toshiroh; Imazato, Shin; Kudo, Michiaki; Ohta, Tomoyuki; Mizuhara, Akihiro; Tamamori, Yutaka; Muramatsu, Hirohito; Nishiguchi, Yukio; Nishiyama, Yorihiro; Takahashi, Mikako; Nishiwaki, Shinji; Matsumoto, Masami; Goshi, Satoshi; Sakamoto, Shigeo; Uchida, Nobuyuki; Ijima, Masashi; Ogawa, Tetsushi; Shimazaki, Makoto; Takei, Shinichi; Kimura, Chikou; Yamashita, Satoyoshi; Endo, Takao; Nakahori, Masato; Itoh, Akihiko; Kusakabe, Toshiro; Ishizuka, Izumi; Iiri, Takao; Fukasawa, Shingo; Arimoto, Yukitsugu; Kajitani, Nobuaki; Ishida, Kazuhiko; Onishi, Koji; Taira, Akihiko; Kobayashi, Makoto; Itano, Yasuto; Kobuke, Toshiya

2009-01-01

During tube exchange for percutaneous endoscopic gastrostomy (PEG), a misplaced tube can cause peritonitis and death. Thus, endoscopic or radiologic observation is required at tube exchange to make sure the tube is placed correctly. However, these procedures cost extensive time and money to perform in all patients at the time of tube exchange. Therefore, we developed the "sky blue method" as a screening test to detect misplacement of the PEG tube during tube exchange. First, sky blue solution consisting of indigocarmine diluted with saline was injected into the gastric space via the old PEG tube just before the tube exchange. Next, the tube was exchanged using a standard method. Then, we checked whether the sky blue solution could be collected through the new tube or not. Finally, we confirmed correct placement of the tube by endoscopic or radiologic observation for all patients. A total of 961 patients were enrolled. Each tube exchange took 1 to 3 minutes, and there were no adverse effects. Four patients experienced a misplaced tube, all of which were detectable with the sky blue method. Diagnostic parameters of the sky blue method were as follows: sensitivity, 94% (95%CI: 92-95%); specificity, 100% (95%CI: 40-100%); positive predictive value, 100% (95%CI: 100-100%); negative predictive value, 6% (95%CI: 2-16%). These results suggest that the number of endoscopic or radiologic observations to confirm correct replacement of the PEG tube may be reduced to one fifteenth using the sky blue method.

Crying Baby? How to Keep Your Cool

Science.gov (United States)

... fatal. If you're having trouble managing your emotions or dealing with parenthood, seek help. Your baby's ... infant-and-toddler-health/in-depth/crying-baby/art-20046995 . Mayo Clinic Footer Legal Conditions and Terms ...

Baby boom generation at the retirement onset

Directory of Open Access Journals (Sweden)

Stojilković Jelena

2010-01-01

Full Text Available Sudden increase in the number of live births after the Second World War due to an increase in fertility rates has led to the formation of cohorts with specific characteristics or baby boom generation. This generation is unique in the history of the demographic phenomenon that has affected and affects the functioning of many segments of society. The aim of this paper is to assess structure of baby boomers who are few years away from retirement, using demographic data. Impact of baby boomer age structure of current and future retirees is described with a graphical display of current and projected age pyramid of baby boomers. Demographic pattern that women live longer than men is evident in the projected pyramid. In addition, the number of baby boomers will lead to a "younger" old population. The imbalance in the number of men and women pensioners, as well as older cohorts of women and female baby boomers was analyzed. As a result, an increasing trend of women's age pensioners who are members of the baby boom generation was clearly observed, which is opposite to the older cohort of women who often were family pensioners. Different circumstances and conditions in which female boomers lived and worked will form a new "pension model" because they will gain their benefits as well as men, for the first time in significant number, unlike their mothers, which gained the right to retire after they become widows. Number of women age pensioners is getting greater comparing to men, as the result of changes in the economic activities of women in the last half of the 20th century. When baby boomers retire and exit the working population, this will create a vacuum, because the numerically smaller generations will enter working population, while the sudden and very shortly, the number of population older than 60 or 65 will increase, most of them will likely to acquire the right to a pension. It is undeniable that baby boomers had impact on demographic structure

Five Tubes Rupture at Cold Side of Steam Generator Simulation Test Report Using the ATLAS

International Nuclear Information System (INIS)

Kang, Kyoung Ho; Park, Hyun Sik; Cho, Seok

2010-12-01

In this study, a postulated SGTR event of the APR1400 was experimentally investigated with the ATLAS. In order to simulate a double-ended rupture of five U-tubes in the APR1400, the SGTR-CL-02 test was performed with the ATLAS. The main objectives of this test were not only to provide a physical insight into the system response of the APR1400 during the SGTR but also to produce integral effect experimental data to validate the safety analysis code. In the present report, major thermal-hydraulic phenomena such as the system pressures, the collapsed water levels, and the break flow rate were presented and discussed. Compared to the case of a single U-tube rupture test, opening frequency of the MSSVs in the intact steam generator (SG-2) was highly reduced after 500 seconds in the present SGTR-CL-02 test. Large discharge of the primary inventory resulted in rapid depressurization of the primary system and consequently early injection of the SIP. Supply of cold ECC water by the SIPs reduced the energy transfer to the secondary side compared with the single U-tube rupture case. Less heat transfer to the secondary side had more influence on the secondary pressure of the affected steam generator than the break flow. This integral effect test data will be used to evaluate the prediction capability of existing safety analysis codes of the MARS and the RELAP5 as well as the SPACE code

Five Tubes Rupture at Hot Side of Steam Generator Simulation Test Report Using the ATLAS

International Nuclear Information System (INIS)

Kang, Kyoung Ho; Park, Hyun Sik; Cho Seok

2010-12-01

In this study, a postulated SGTR event of the APR1400 was experimentally investigated with the ATLAS. In order to simulate a double-ended rupture of five U-tubes in the APR1400, the SGTR-HL-05 test was performed with the ATLAS. The main objectives of this test were not only to provide a physical insight into the system response of the APR1400 during the SGTR but also to produce integral effect experimental data to validate the SPACE code. In the present report, major thermal-hydraulic phenomena such as the system pressures, the collapsed water levels, and the break flow rate were presented and discussed. On the contrary to the case of a single U-tube rupture test, the MSSV of the intact steam generator was not opened any more after 1500 seconds in the present SGTR-HL-05 test. Large discharge of the primary inventory resulted in rapid depressurization of the primary system and consequently early injection of the SIP. Supply of cold ECC water by the SIPs reduced the energy transfer to the secondary side compared with the single U-tube rupture case. Less heat transfer to the secondary side had more influence on the secondary pressure of the affected steam generator than the break flow. This integral effect test data will be used to evaluate the prediction capability of existing safety analysis codes of the MARS and the RELAP5 as well as the SPACE code

Atmosphere in a Test Tube

Science.gov (United States)

Claudi, R.; Pace, E.; Ciaravella, A.; Micela, G.; Piccioni, G.; Billi, D.; Cestelli Guidi, M.; Coccola, L.; Erculiani, M. S.; Fedel, M.; Galletta, G.; Giro, E.; La Rocca, N.; Morosinotto, T.; Poletto, L.; Schierano, D.; Stefani, S.

The ancestor philosophers' dream of thousand of new world is finally realised: more than 1800 extrasolar planets have been discovered in the neighborhood of our Sun. Most of them are very different from those we used to know in our Solar System. Others orbit the Habitable Zone (HZ) of their parent stars. Space missions, as JWST and the very recently proposed ARIEL, or ground based instruments, like SPHERE@VLT, GPI@GEMINI and EPICS@ELT, have been proposed and built to measure the atmospheric transmission, reflection and emission spectra over a wide wavelength range of these new worlds. In order to interpret the spectra coming out by this new instrumentation, it is important to know in detail the optical characteristics of gases in the typical physical conditions of the planetary atmospheres and how those characteristics could be affected by radiation driven photochemical and bio-chemical reaction. Insights in this direction can be achieved from laboratory studies of simulated planetary atmosphere of different pressure and temperature conditions under the effects of radiation sources, used as proxies of different bands of the stellar emission. ''Atmosphere in a Test Tube'' is a collaboration among several Italian astronomical, biological and engineering institutes in order to share their experiencece in performing laboratory experiments on several items concerning extrasolar planet atmospheres.

Development of Baby-EBM Interface System

International Nuclear Information System (INIS)

Mukhlis Mokhtar; Abu Bakar Ghazali; Muhammad Zahidee Taat

2010-01-01

This paper explains the works being done to develop an interface system for Baby-Electron Beam Machine (EBM). The function of the system is for the safety, controlling and monitoring the Baby-EBM. The integration for the system is using data acquisition (DAQ) hardware and LabVIEW to develop the software. (author)

Development of Baby-EBM Interface System

Energy Technology Data Exchange (ETDEWEB)

Mokhtar, Mukhlis; Ghazali, Abu Bakar; Taat, Muhammad Zahidee [Accelerator Development Center, Malaysian Nuclear Agency, Bangi, Kajang, Selangor (Malaysia), Technical Support Div.

2010-07-01

This paper explains the works being done to develop an interface system for Baby-Electron Beam Machine (EBM). The function of the system is for the safety, controlling and monitoring the Baby-EBM. The integration for the system is using data acquisition (DAQ) hardware and LabVIEW to develop the software. (author)

Infants & Toddlers: How Babies Use Gestures to Communicate

Science.gov (United States)

Honig, Alice Sterling

2004-01-01

Evolution has provided babies with wonderful ways to get the loving attention and care that they need from adults. When a baby is distressed, his cry is the most primitive and powerful tool for bringing help. By the time a baby is 2 or 3 months old, his dazzling smile and crooked grin evokes tenderness, smiles, and nurturance from adults who are…

Study of tensile test behavior of austenitic stainless steel type 347 seamless thin-walled tubes in cold worked condition

Energy Technology Data Exchange (ETDEWEB)

Terui, Clarice, E-mail: clarice.terui@marinha.mil.br [Centro Tecnológico da Marinha em São Paulo (CINA/CTMSP), Iperó, SP (Brazil). Centro Industrial Nuclear da Marinha; Lima, Nelson B. de, E-mail: nblima@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNE-SP), Sao Paulo, SP (Brazil)

2017-07-01

These austenitic stainless steel type 347 seamless thin-walled tubes are potential candidates to be used in fuel elements of nuclear power plants (as PWR - Pressurized Water Reactor). So, their metallurgical condition and mechanical properties, as the tensile strength and yield strength, normally are very restrict in demanding project and design requirements. Several full size tensile tests at room temperature and high temperature (315 deg C) were performed in these seamless tubes in cold-worked condition. The results of specified tensile and yield strengths were achieved but the elongation of the tube, in the geometry of the component, could not be measured at high temperature due to unconventional mode of rupture (helical mode without separation of parts). The average value of elongation was obtained from stress-strain curves of hot tensile tests and was around 5%. The results obtained in this research show that this behavior of the full size tensile test samples of thin-walled tube (wall thickness less than 0.5 mm) in high temperature (315°C) is due to the combination of the manufacturing process, the material (crystallographic structure and chemical composition) and the final geometry of the component. In other words, the strong crystallographic texture of material induced by tube drawing process in addition with the geometry of the component are responsible for the behavior in hot uniaxial tensile tests. (author)

Ferruleless coupled-cavity traveling-wave tube cold-test characteristics simulated with micro-SOS

Science.gov (United States)

Schroeder, Dana L.; Wilson, Jeffrey D.

1993-01-01

The three-dimensional, electromagnetic circuit analysis code, Micro-SOS, can be used to reduce expensive and time consuming experimental 'cold-testing' of traveling-wave tube (TWT) circuits. The frequency-phase dispersion and beam interaction impedance characteristics of a ferruleless coupled-cavity traveling-wave tube slow-wave circuit were simulated using the code. Computer results agree closely with experimental data. Variations in the cavity geometry dimensions of period length and gap-to-period ratio were modeled. These variations can be used in velocity taper designs to reduce the radiofrequency (RF) phase velocity in synchronism with the decelerating electron beam. Such circuit designs can result in enhanced TWT power and efficiency.

Breastfeeding Your Baby

Science.gov (United States)

... milk is easier to digest than formula. • Breast milk contains antibodies that protect infants from certain illnesses, such as ear infections, diarrhea, respiratory illnesses, and allergies. The longer your baby breastfeeds, ...

Should we maintain baby hatches in our society?

Directory of Open Access Journals (Sweden)

Asai Atsushi

2013-02-01

Full Text Available Abstract Background A baby hatch called the “Stork’s Cradle” has been in place at Jikei Hospital in Kumamoto City, Japan, since May 10, 2007. Babyklappes were first established in Germany in 2000, and there are currently more than 90 locations. Attitudes regarding baby hatches are divided in Japan and neither opinions for nor against baby hatches have thus far been overwhelming. To consider the appropriateness of baby hatches, we present and examine the validity of each major objection to establishing baby hatches. Discussion There are various objections to baby hatches as follows: It violates a child’s right to know the identity of his or her biological parents by allowing anonymous birth; it neglects fulfillment of the biological parents’ basic obligation to raise their child and its very availability induces abandonment of infants; some people abuse it for very selfish reasons; it cannot save babies’ lives; the rights of one parent can be ignored if the other surrenders a child without his or her consent; it puts a baby in medical jeopardy; and it has no clear legal basis. The authors would argue that there are many plausible refutations for each objection mainly based on priority of child’s right to life, pregnant women’s vulnerability and necessity of anonymity, social responsibility to protect and raise children, differences between dropping a child off at a baby hatch and child neglect, limited function of social childcare center, inevitability of abuse by a minority of people, necessary distinction between outcomes that occur only because baby hatches exist and those that occur regardless of their existence, important local direct and upmost measures for women in trouble, and difference between ambiguous legality and illegality. Summary We argue that a certain number of baby hatches should continue to be established as a last resort, in a form that can maintain anonymity if the parent dropping the child off so desires. It

Baby Cry Detection in Domestic Environment using Deep Learning

OpenAIRE

Ijzerman, Hans

2017-01-01

Automatic detection of a baby cry in audio signals is an essential step in applications such as remote baby monitoring. It is also important for researchers, who study the relation between baby cry patterns and various health or developmental parameters. In this paper, we propose two machine-learning algorithms for automatic detection of baby cry in audio recordings. The first algorithm is a low-complexity logistic regression classifier, used as a reference. To train this classifier, we extra...

Bond strength tests between silicon wafers and duran tubes (fusion bonded fluidic interconnects)

NARCIS (Netherlands)

Fazal, I.; Berenschot, Johan W.; de Boer, J.H.; Jansen, Henricus V.; Elwenspoek, Michael Curt

2005-01-01

The fusion bond strength of glass tubes with standard silicon wafers is presented. Experiments with plain silicon wafers and those coated with silicon oxide and silicon nitride are presented. Results obtained are discussed in terms of homogeneity and strength of fusion bond. High pressure testing

Pressure loss characteristics of LSTF steam generator heat-transfer tubes. Pressure loss increase due to tube internal instruments

International Nuclear Information System (INIS)

Suzuki, Mitsuhiro

1994-11-01

The steam generator of the Large-Scale Test Facility (LSTF) includes 141 heat-transfer U-tubes with different lengths. Six U-tubes among them are furnished with 15 or 17 probe-type instruments (conduction probe with a thermocouple; CPT) protuberant into the primary side of the U-tubes. Other 135 U-tubes are not instrumented. This results in different hydraulic conditions between the instrumented and non-instrumented U-tubes with the same length. A series of pressure loss characteristics tests was conducted at a test apparatus simulating both types of U-tube. The following pressure loss coefficient (K CPT ) was reduced as a function of Reynolds number (Re) from these tests under single-phase water flow conditions. K CPT =0.16 5600≤Re≤52820, K CPT =60.66xRe -0.688 2420≤Re≤5600, K CPT =2.664x10 6 Re -2.06 1371≤Re≤2420. The maximum uncertainty is 22%. By using these results, the total pressure loss coefficients of full length U-tubes were estimated. It is clarified that the total pressure loss of the shortest instrumented U-tube is equivalent to that of the middle-length non-instrumented U-tube and also that a middle-length instrumented U-tube is equivalent to the longest non-instrumented U-tube. Concludingly. it is important to take account of the CPT pressure loss mentioned above in estimation of fluid behavior at the non-instrumented U-tubes either by using the LSTF experiment data from the CPT-installed U-tubes or by using any analytical codes. (author)

Immunizations for Preterm Babies

Science.gov (United States)

... Issues Health Issues Health Issues Conditions Injuries & Emergencies Vaccine Preventable Diseases ... Children > Safety & Prevention > Immunizations > Immunizations For Preterm Babies Safety & ...

Birthing Healthy Babies (A Cup of Health with CDC)

Centers for Disease Control (CDC) Podcasts

Every four and a half minutes a baby is born with a birth defect in the United States. That means nearly 120,000 babies, or about three percent of all babies born each year. In this podcast, Dr. Suzanne Gilboa discusses ways to prevent birth defects.

Baby universe theory

International Nuclear Information System (INIS)

Nielsen, H.B.; Ninomiya, Masao

1989-12-01

We give an elementary review of the so called 'the theory of baby universes' which is a series of ideas or speculations about some effects in quantum gravity, viz. the effect of a certain type of wormholes, representing the exchange of small 3-space universes called baby universes. We consider this 'theory' as being physically and scientifically a very promising candidate for a theory of everything. It is, however, mathematically lacking any strong foundation at all. It solves several fine-tuning problems: First of all the cosmological constant problem, and also the strong CP-problem and the hierarchy problem. We also speculate that it might predict the possibility of influencing the probability distributions of the outcome of quantum mechanical measurements at one time by acts at a later time. (orig.)

Optimization and testing of dried antibody tube: The EuroFlow LST and PIDOT tubes as examples

NARCIS (Netherlands)

V.H.J. van der Velden (Vincent); J. Flores-Montero (Juan); M. Perez-Andres; M. Martin-Ayuso (M.); Crespo, O. (Oliver); Blanco, E. (Elena); T. Kalina (Tomas); J. Philippé (Jan); Bonroy, C. (Carolien); M. de Bie (Maaike); J.G. te Marvelde (Jeroen); C. Teodosio (Cristina); Corral Mateos, A. (Alba); V. Kanderová (V.); M. van der Burg (Mirjam); Van Hoof, D. (Dennis); J.J.M. van Dongen (Jacques); A. Orfao (Alberto)

2017-01-01

textabstractWithin EuroFlow, we recently developed screening tubes for hematological malignancies and immune deficiencies. Pipetting of antibodies for such 8-color 12-marker tubes however is time-consuming and prone to operational mistakes. We therefore evaluated dried formats of the lymphocytosis

God-mother-baby: what children think they know.

Science.gov (United States)

Kiessling, Florian; Perner, Josef

2014-01-01

This study tested one hundred and nine 3- to 6-year-old children on a knowledge-ignorance task about knowledge in humans (mother, baby) and God. In their responses, participants not reliably grasping that seeing leads to knowing in humans (pre-representational) were significantly influenced by own knowledge and marginally by question format. Moreover, knowledge was attributed significantly more often to mother than baby and explained by agent-based characteristics. Of participants mastering the task for humans (representational), God was largely conceived as ignorant "man in the sky" by younger and increasingly as "supernatural agent in the sky" by older children. Evidence for egocentrism and for anthropomorphizing God lends support to an anthropomorphism hypothesis. First-time evidence for an agent-based conception of others' knowledge in pre-representational children is presented. © 2013 The Authors. Child Development © 2013 Society for Research in Child Development, Inc.

A simple in vitro test tube method for estimating the bioavailability of phosphorus in feed ingredients for swine.

Science.gov (United States)

Bollinger, David W; Tsunoda, Atsushi; Ledoux, David R; Ellersieck, Mark R; Veum, Trygve L

2004-04-07

A simplified in vitro test tube (TT) method was developed to estimate the percentage of available P in feed ingredients for swine. The entire digestion procedure with the TT method consists of three consecutive enzymatic digestions carried out in a 50-mL conical test tube: (1) Pre-digestion with endo-xylanase and beta-glucanase for 1 h, (2) peptic digestion for 2 h, and (3) pancreatic digestion for 2 or 4 h. The TT method is simpler and much easier to perform compared to the dialysis tubing (DT) method, because dialysis tubing is not used. Reducing sample size from 1.0 to 0.25 g for the TT method improved results. In conclusion, the accuracy and validity of the TT method is equal to that of our more complicated DT method (r = 0.97, P < 0.001), designed to mimic the digestive system of swine, for estimating the availability of P in plant-origin feed ingredients.

Long term testing of materials for tube shielding, stage 2; Laangtidsprovning av tubskyddsmaterial, etapp 2

Energy Technology Data Exchange (ETDEWEB)

Norling, Rikard; Hjoernhede, Anders; Mattsson, Mattias

2012-02-15

temperature. It varies from a few months to several years. The cost of replacing tube shielding is significant, which calls for improved materials. In a previous study [1] various materials have been tested in the WtE CFB-boiler P14 at Haendeloe in Norrkoeping, Sweden. The study showed that several materials may be cost effective candidates for replacing 253MA, but the test period was too short for safe predictions. This work includes exposures at the same position, but with extended test period up to almost 12000 h to verify the previous results. In addition results from exposures in the WtE CFB-boiler Hoegdalen P6 in Stockholm, Sweden is included. This boiler suffers in particular from severe erosion of the tube shielding requiring it to be exchanged every few months

Baby bottle steam sterilizers disinfect home nebulizers inoculated with bacterial respiratory pathogens.

Science.gov (United States)

Towle, Dana; Callan, Deborah A; Farrel, Patricia A; Egan, Marie E; Murray, Thomas S

2013-09-01

Contaminated nebulizers are a potential source of bacterial infection but no single method is universally accepted for disinfection. We hypothesized that baby-bottle steam sterilizers effectively disinfect home nebulizers. Home nebulizers were inoculated with the common CF respiratory pathogens methicillin resistant Staphylococcus aureus, Burkholderia cepacia, Haemophilus influenzae, mucoid and non mucoid Pseudomonas aeruginosa, and Stenotrophomonas maltophilia. The nebulizers were swabbed for bacterial growth, treated with either the AVENT (Philips), the NUK Quick & Ready (Gerber) or DRY-POD (Camera Baby) baby bottle steam sterilizer and reswabbed for bacterial growth. All steam sterilizers were effective at disinfecting all home nebulizers. Viable bacteria were not recovered from any inoculated site after steam treatment, under any conditions tested. Steam treatment is an effective disinfection method. Additional studies are needed to confirm whether these results are applicable to the clinical setting. Copyright © 2012 European Cystic Fibrosis Society. Published by Elsevier B.V. All rights reserved.

How to Keep Your Sleeping Baby Safe

Science.gov (United States)

... first hour. After that, or when the mother needs to sleep or cannot do skin-to-skin, babies should ... Back is Best New Crib Standards: What Parents Need to Know Safe Sleep for Babies (Video) The Healthy Children Show: Sleep ( ...

Crying Baby: What to Do When Your Newborn Cries

Science.gov (United States)

... a crying baby — and renewing your ability to handle the tears. By Mayo Clinic Staff The dream: Your baby sleeps through the night after just a few weeks, gurgles happily while you run errands and fusses only when hunger strikes. The reality: Your baby's favorite playtime is after ...

Early Detection of Baby-Rain-Cell Aloft in a Severe Storm and Risk Projection for Urban Flash Flood

Directory of Open Access Journals (Sweden)

Eiichi Nakakita

2017-01-01

Full Text Available In July 2008, five people were killed by a tragic flash flood caused by a local torrential heavy rainfall in a short time in Toga River. From this tragic accident, we realized that a system which can detect hazardous rain-cells in the earlier stage is strongly needed and would provide an additional 5 to 10 min for evacuation. By analyzing this event, we verified that a first radar echo aloft, by volume scan observation, is a practical and important sign for early warning of flash flood, and we named a first echo as a “baby-rain-cell” of Guerrilla-heavy rainfall. Also, we found a vertical vorticity criterion for identifying hazardous rain-cells and developed a heavy rainfall prediction system that has the important feature of not missing any hazardous rain-cell. Being able to detect heavy rainfall by 23.6 min on average before it reaches the ground, this system is implemented in XRAIN in the Kinki area. Additionally, to resolve the relationship between baby-rain-cell growth and vorticity behavior, we carried out an analysis of vorticity inside baby-rain-cells and verified that a pair of positive and negative vertical vortex tubes as well as an updraft between them existed in a rain-cell in the early stage.

Dose conversion coefficients for paediatric CT examinations with automatic tube current modulation

International Nuclear Information System (INIS)

Schlattl, H; Zankl, M; Becker, J; Hoeschen, C

2012-01-01

A common dose-saving technique used in modern CT devices is automatic tube current modulation (TCM), which was originally designed to also reduce the dose in paediatric CT patients. In order to be able to deduce detailed organ doses of paediatric models, dose conversion coefficients normalized to CTDI vol for an eight-week-old baby and seven- and eight-year-old children have been computed accounting for TCM. The relative difference in organ dose conversion coefficients with and without TCM is for many organs and examinations less than 10%, but can in some cases amount up to 30%, e.g., for the thyroid in the chest CT of the seven-year-old child. Overall, the impact of TCM on the conversion coefficients increases with increasing age. Besides TCM, also the effect of collimation and tube voltage on organ dose conversion coefficients has been investigated. It could be shown that the normalization to CTDI vol leads to conversion coefficients that can in most cases be considered to be independent of collimation and tube voltage. (paper)

Effects of baby-friendly hospital initiative on breast-feeding practices in Sindh

International Nuclear Information System (INIS)

Khan, M.; Akram, D.S.

2013-01-01

To determine changes in the breastfeeding practices of mothers after receiving counseling on Ten Steps to Successful Breastfeeding as defined by the Baby Friendly Hospital Initiative comparing baby friendly hospitals (BFHs) and non-baby-friendly hospitals in Sindh, Pakistan. Methods: The observational study was conducted from June 2007 to June 2009 in randomly selected baby-friendly and non-baby-friendly hospitals of Sindh, Pakistan. Non-probability purposive sampling was employed. The maternity staff was trained on Ten Steps to Successful Breastfeeding. The changes in breastfeeding practices were analysed by SPSS version 15. Results: A total of 236 women were included in the study. Of them, 196 (83.05%) were from baby-friendly hospitals and 40 (16.94%) from non-baby-friendly hospitals. Besides, 174 (88.7%) mothers in baby-friendly hospitals and 5 (12.5%) in non-baby-friendly hospitals during antenatal care received counseling by healthcare providers. There was an increase in breastfeeding practice up to 194 (98.97%) in the first category compared to 12 (30%) in the other category. Conclusion: Counseling under the Baby Friendly Hospital Initiative improved breastfeeding practices up to 98.97% in baby-friendly compared to non-baby-friendly hospitals. (author)

Approximating a free-field blast environment in the test section of an explosively driven conical shock tube

Science.gov (United States)

Stewart, J. B.

2018-02-01

This paper presents experimental data on incident overpressures and the corresponding impulses obtained in the test section of an explosively driven 10° (full angle) conical shock tube. Due to the shock tube's steel walls approximating the boundary conditions seen by a spherical sector cut out of a detonating sphere of energetic material, a 5.3-g pentolite shock tube driver charge produces peak overpressures corresponding to a free-field detonation from an 816-g sphere of pentolite. The four test section geometries investigated in this paper (open air, cylindrical, 10° inscribed square frustum, and 10° circumscribed square frustum) provide a variety of different time histories for the incident overpressures and impulses, with a circumscribed square frustum yielding the best approximation of the estimated blast environment that would have been produced by a free-field detonation.

Integrity Assessment of GOH Heater Tube

Energy Technology Data Exchange (ETDEWEB)

Lee, Bong Sang; Hong, J. H.; Oh, Y. J.; Yoon, J. H.; Oh, J. M. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1997-08-01

An assessment of structural integrity of ASTM A312-TP347 GOH heater tube was performed. The surface notches which had been produced during tube manufacturing process were analyzed microscopically. Chemical analysis, hardness tests, tensile tests, and J-Integral fracture resistance tests were carried out to compare the mechanical properties with those of the material specification and also with the other material of the same type. The test results showed the mechanical properties of the GOH tube material are within the specification range. An elastic-plastic fracture mechanics analysis based on the DPFAD method reveals the tube an appropriate safety margin for the normal operation. 13 refs., 5 tabs., 24 figs. (author)

Effect of tube-support interaction on the dynamic responses of heat exchanger tubes

International Nuclear Information System (INIS)

Shin, Y.S.; Jendrzejczyk, J.A.; Wambsganss, M.W.

1977-01-01

Operating heat exchangers have experienced tube damages due to excessive flow-induced vibration. The relatively small inherent tube-to-baffle hole clearances associated with manufacturing tolerances in heat exchangers affect the tube vibrational characteristics. In attempting a theoretical analysis, questions arise as to the effects of tube-baffle impacting on dynamic responses. Experiments were performed to determine the effects of tube-baffle impacting in vertical/horizontal tube orientation, and in air/water medium on the vibrational characteristics (resonant frequencies, mode shapes, and damping) and displacement response amplitudes of a seven-span tube model. The tube and support conditions were prototypic, and overall length approximately one-third that of a straight tube segment of the steam generator designed for the CRBR. The test results were compared with the analytical results based on the multispan beam with ''knife-edge'' supports

N Reactor pressure tube 1350 postirradiation examination

International Nuclear Information System (INIS)

Cook, D.J.

1977-01-01

The N Reactor pressure tubes were fabricated from Zircaloy-2 primarily due to the excellent corrosion resistance, low neutron absorption, and high strength properties of this alloy. Irradiation damage mechanisms increase the strength and decrease the ductility of the Zircaloy-2. Irradiation data available at the time the tubes were installed indicated that fast neutron irradiation damage mechanisms would not decrease the ductility to unacceptable levels over the estimated plant life of 25 to 30 years. However, because the tubes are a primary coolant system component and only limited data are available on irradiation effects at high fluences, a Postirradiation Examination (PIE) program was developed to assure that service factors do not compromise pressure tube integrity essential to reactor safety. The PIE program requires that a pressure tube be periodically removed from the reactor for destructive testing. The N Reactor Technical Specifications specify that the frequency of pressure tube removal and examination be based upon the previous PIE test results. Four pressure tubes were examined before tube 1350, and the test results were summarized in individual reports. PIE results on tube 1350 were summarized along with the test results on the previous four tubes in a previous report. The purpose of this report is to present in detail the results on PIE of pressure tube 1350, and, in particular, document the technique by which the fracture toughness of the pressure tube was determined

Sex stereotypes influence adults' perception of babies' cries.

Science.gov (United States)

Reby, David; Levréro, Florence; Gustafsson, Erik; Mathevon, Nicolas

2016-04-14

Despite widespread evidence that gender stereotypes influence human parental behavior, their potential effects on adults' perception of babies' cries have been overlooked. In particular, whether adult listeners overgeneralize the sex dimorphism that characterizes the voice of adult speakers (men are lower-pitched than women) to their perception of babies' cries has not been investigated. We used playback experiments combining natural and re-synthesised cries of 3 month-old babies to investigate whether the interindividual variation in the fundamental frequency (pitch) of cries affected adult listeners' identification of the baby's sex, their perception the baby's femininity and masculinity, and whether these biases interacted with their perception of the level of discomfort expressed by the cry. We show that low-pitched cries are more likely to be attributed to boys and high-pitched cries to girls, despite the absence of sex differences in pitch. Moreover, low-pitched boys are perceived as more masculine and high-pitched girls are perceived as more feminine. Finally, adult men rate relatively low-pitched cries as expressing more discomfort when presented as belonging to boys than to girls. Such biases in caregivers' responses to babies' cries may have implications on children's immediate welfare and on the development of their gender identity.

Colloidon baby – Rare case with preventable complications

Directory of Open Access Journals (Sweden)

Janardhan Bommakanti

2015-01-01

Full Text Available Colloidon baby is a rare congenital disorder characterized clinical-ly by parchment like taught membrane covering the whole body at the time of birth, which subsequently develops Non bullous ichthyosiform erythroderma or Lamellar ichthyiosis in most cases and in few cases other ichthyosiform disorders. The colloidon membrane spontaneously desquamates within 2 weeks or up to 3 months in few cases. Herein, we present 2 cases of colloidon babies born to consanguineously married couples of which the first baby was born at term by normal vaginal delivery and second baby born prematurely by caesarean section. Both 1st & 2nd baby were delivered in different private hospitals in villages of Nizamabad district, Telangana state and reported to tertiary level children’s hospital in Hyderabad city on 4nd and 6th day of life respectively with complaints of colloidon membrane and macera-tion of skin in diaper area, was admitted in Neonatal intensive care unit (NICU in humidified incubator, treated with emollients, intra-venous fluids and prophylactic antibiotics to avoid complications. Nursing care is of prime importance. This presentation was aimed at stressing not only the importance of early recognition by pedia-trician & timely referral to dermatologist and ophthalmologist for saving life of affected baby but also equal importance to proper nursing care.

Safe Sleep for Babies PSA (:60)

Centers for Disease Control (CDC) Podcasts

2018-01-09

This 60 second public service announcement is based on the January 2018 CDC Vital Signs report. Every year, there are about 3,500 sleep-related deaths among U.S. babies. Learn how to create a safe sleep environment for babies.  Created: 1/9/2018 by Centers for Disease Control and Prevention (CDC).   Date Released: 1/9/2018.

Three-parent baby: Is it ethical?

Science.gov (United States)

Dahiya, Neha; Garg, Suneela

2018-01-01

The UK was the first country to legalise mitochondrial donation in October 2015 (1). In 2016, the first three-parent baby was born in Mexico (2) and the US Food and Drug Administration declared that further research on mitochondrial donation is ethically permissible (3). It has now become an important issue, raising as it does, the spectre of "genetically modified designer babies".

Feeding Your Baby

Medline Plus

Full Text Available ... discomforts . If you’re feeding your baby formula , find out how to choose the best one for ... care they receive. We're pioneering research to find solutions. We're empowering families with the knowledge ...

Feeding Your Baby

Medline Plus

Full Text Available ... Careers Events in your area Frequently asked questions Email sign up Join our online community March for ... Careers Events in your area Frequently asked questions Email sign up Join our online community Home > Baby > ...

Feeding Your Baby

Medline Plus

Full Text Available ... Content] March For Babies | Nacersano | Share Your Story Register | Sign In Hi | Your dashboard | sign out Donate ... DONATE sign up sign in sign out account center my dashboard Our Cause Our mission Fighting premature ...

Feeding Your Baby

Medline Plus

Full Text Available ... this page It's been added to your dashboard . Time to eat! Feeding your baby helps her grow healthy and strong. It’s also a great time for you and your partner to bond with ...

Feeding Your Baby

Medline Plus

Full Text Available ... The Prematurity Campaign About us Annual report Our work Community impact Global programs Research Need help? Frequently ... for your baby during the first year of life. Learn how to breastfeed and why breast milk ...

Feeding Your Baby

Medline Plus

Full Text Available ... bond with her. Breast milk is the best food for your baby during the first year of ... feeding safe. And then get ready for solid foods ! In This Topic Breastfeeding help Breastfeeding is best ...

Feeding Your Baby

Medline Plus

Full Text Available ... The Prematurity Campaign About us Annual report Our work Community impact Global programs Research Need help? Frequently ... bond with her. Breast milk is the best food for your baby during the first year of ...

Feeding Your Baby

Medline Plus

Full Text Available ... us on Twitter Instagram: behind the scenes Our research Research grants Prematurity research Birth defects research Infant ... bond with her. Breast milk is the best food for your baby during the first year of ...

Assembly and method for testing the integrity of stuffing tubes

Energy Technology Data Exchange (ETDEWEB)

Morrison, E.F.

1996-12-31

A stuffing tube integrity checking assembly includes first and second annular seals, with each seal adapted to be positioned about a stuffing tube penetration component. An annular inflation bladder is provided, the bladder having a slot extending longitudinally there along and including a separator for sealing the slot. A first valve is in fluid communication with the bladder for introducing pressurized fluid to the space defined by the bladder when mounted about the tube. First and second releasible clamps are provided. Each clamp assembly is positioned about the bladder for securing the bladder to one of the seals for thereby establishing a fluid-tight chamber about the tube.

Construction and test of high precision drift-tube (sMDT) chambers for the ATLAS muon spectrometer

CERN Document Server

Nowak, Sebastian; Kroha, Hubert; Schwegler, Philipp; Sforza, Federico

2014-01-01

For the upgrade of the ATLAS muon spectrometer in March 2014 new muon tracking chambers (sMDT) with drift-tubes of 15 mm diameter, half of the value of the standard ATLAS Monitored Drift-Tubes (MDT) chambers, and 10~$\\mu$m positioning accuracy of the sense wires have been constructed. The new chambers are designed to be fully compatible with the present ATLAS services but, with respect to the previously installed ATLAS MDT chambers, they are assembled in a more compact geometry and they deploy two additional tube layers that provide redundant rack information. The chambers are composed of 8 layers of in total 624 aluminium drift-tubes. The assembly of a chamber is completed within a week. A semi-automatized production line is used for the assembly of the drift-tubes prior to the chamber assembly. The production procedures and the quality control tests of the single components and of the complete chambers will be discussed. The wire position in the completed chambers have been measured by using a coordinate me...

Baby universes in string theory

International Nuclear Information System (INIS)

Dijkgraaf, Robbert; Gopakumar, Rajesh; Ooguri, Hirosi; Vafa, Cumrun

2006-01-01

We argue that the holographic description of four-dimensional Bogomol'nyi-Prasad-Sommerfield black holes naturally includes multicenter solutions. This suggests that the holographic dual to the gauge theory is not a single AdS 2 xS 2 but a coherent ensemble of them. We verify this in a particular class of examples, where the two-dimensional Yang-Mills theory gives a holographic description of the black holes obtained by branes wrapping Calabi-Yau cycles. Using the free fermionic formulation, we show that O(e -N ) nonperturbative effects entangle the two Fermi surfaces. In an Euclidean description, the wave function of the multicenter black holes gets mapped to the Hartle-Hawking wave function of baby universes. This provides a concrete realization, within string theory, of effects that can be interpreted as the creation of baby universes. We find that, at least in the case we study, the baby universes do not lead to a loss of quantum coherence, in accord with general arguments

Eddy-current testing of nuclear fuel cladding tubes using tilted encircling coil system, 1

International Nuclear Information System (INIS)

Yin, Renzhong; Sekine, Kazuyoshi; Shimizu, Hisaji; Tsukui, Kazushige; Urata, Megumu.

1989-01-01

The eddy current testing method with external encircling-coils has been widely used as a standard technique for inspection of defects in irradiated zircaloy cladding tubes. In this inspection, the systematic procedure to reliably characterize defects is required. This paper describes the newly developed external tilted encircling-coil system, in which the coil axis is inclined by an angle α to the sample tube axis, for reliable determination of the sort, location and size of defects. As the results of experimental work concerning some kinds of artificial defects in zircaloy cladding tubes using newly designed tilted coil system, an adaptable general-procedure for characterization of defects has been proposed. Furthermore, it has been confirmed that in the case of smaller tilt angles of coil, the signal-to noise ratio for defect response in this coil system is approximately equal to that of ordinary encircling coil system. (author)

Evaluation of steam generator tube integrity during earthquakes

Energy Technology Data Exchange (ETDEWEB)

Kusakabe, Takaya; Kodama, Toshio [Mitsubishi Heavy Industries Ltd., Kobe (Japan). Kobe Shipyard and Machinery Works; Takamatsu, Hiroshi; Matsunaga, Tomoya

1999-07-01

This report shows an experimental study on the strength of PWR steam generator (SG) tubes with various defects under cyclic loads which simulate earthquakes. The tests were done using same SG tubing as actual plants with axial and circumferential defects with various length and depth. In the tests, straight tubes were loaded with cyclic bending moments to simulate earthquake waves and number of load cycles at which tube leak started or tube burst was counted. The test results showed that even tubes with very long crack made by EDM more than 80% depth could stand the maximum earthquake, and tubes with corrosion crack were far stronger than those. Thus the integrity of SG tubes with minute potential defects was demonstrated. (author)

Improvement of ISI techniques by multi-frequency eddy current testing method for steam generator tube in PWR plant

International Nuclear Information System (INIS)

Endo, Takashi; Kamimura, Takeo; Nishihara, Masatoshi; Araki, Yasuo; Fukui, Shigetaka.

1982-05-01

Eddy current flaw detection techniques are applied to the in-service inspection (ISI) of steam generator tubes in pressurized water reactors (PWR) plant. To improve the reliability and operating efficiency of the plants, efforts are being made to develop eddy current testing methods of various kinds. Multi-frequency eddy current testing method, one of new method, has recently been applied to actual heat exchanger tubes, contributing to the improvement of the detectability and signal evaluation of the ISI. The outline of multi-frequency eddy current testing method and its effects on the improvement of flaw detecting and signal evaluation accuracy are described. (author)

Using an indwelled test tube as a good "navigator" during enterostomy closure.

Science.gov (United States)

Hirose, Ryuichiro; Tojigamori, Manabu; Obata, Satoshi; Tatsuta, Kyosuke; Kawakubo, Naonori; Arima, Toru

2012-11-01

Surgeons often have difficulty in identifying a suitable incision line to enter the peritoneal cavity for stoma mobilization during enterostomy closure. A mini-size test tube that is preoperatively placed into the stoma can act as an efficient guide in finding a free area to enter the peritoneal cavity, by supplying efficient counter traction and a palpable marker of the intestinal wall.

Feeding Your Baby

Medline Plus

Full Text Available ... Saving Just a moment, please. You've saved this page It's been added to your ... milk is the best food for your baby during the first year of life. Learn how to breastfeed and why ...

Feeding Your Baby

Medline Plus

Full Text Available ... Our work Community impact Global programs Research Need help? Frequently asked questions Contact us Tools & Resources Born ... your dashboard . Time to eat! Feeding your baby helps her grow healthy and strong. It’s also a ...

Breech Babies: What Can I Do If My Baby Is Breech?

Science.gov (United States)

... Control Sex and Sexuality Birth Control Family Health Infants and Toddlers Kids and Teens Pregnancy and Childbirth ... Pregnancy: First TrimesterTaking Care of You and Your Baby While You’re PregnantChanges in Your Body During ...

Expedient Treatment of a Collodion Baby

Directory of Open Access Journals (Sweden)

Michael Chung

2011-01-01

Full Text Available Only ~270 cases of collodion babies have been reported in the literature since 1892. As the name suggests, the term “collodion baby” refers to a phenotype that can be characterized by a yellow, shiny, tight parchment-like membrane stretched over the skin. Although the collodion membrane is only an evanescent condition of the newborn, neonatal complications can occur in 45% of all collodion babies, leading to a mortality rate of ~11% in the first few weeks of life. Most children born as collodion babies will spontaneously desquamate within 2 weeks, but may be as long as 3 months. Eventually, these children develop signs of one of several types of ichthyosis, which gives the skin the appearance of “fish scales.” We report a unique case of a Caucasian male that was born as a Collodion baby at the University of Kentucky Children's Hospital in Lexington, Kentucky. Although the impairment of the skin barrier function put the patient at risk for a number of complications, he improved significantly after being treated with emollients and antibiotics. In contrast to previous findings, we found that skin emollients were beneficial and did not increase the risk of infection.

Hybrid friction diffusion bonding of 316L stainless steel tube-to-tube sheet joints for coil-wound heat exchangers

Energy Technology Data Exchange (ETDEWEB)

Haneklaus, Nils; Cionea, Cristian; Reuven, Rony; Frazer, David; Hosemann, Peter; Peterson, Per F. [Dept of Nuclear Engineering, University of California, Berkeley (United States)

2016-11-15

Hybrid friction diffusion bonding (HFDB) is a solid-state bonding process first introduced by Helmholtz-Zentrum Geesthacht to join aluminum tube-to-tube sheet joints of Coil-wound heat exchangers (CWHE). This study describes how HFDB was successfully used to manufacture 316L test samples simulating tube-to-tube sheet joints of stainless steel CWHE for molten salt coolants as foreseen in several advanced nuclear- and thermal solar power plants. Engineering parameters of the test sample fabrication are presented and results from subsequent non-destructive vacuum decay leak testing and destructive tensile pull-out testing are discussed. The bonded areas of successfully fabricated samples as characterized by tube rupture during pull-out tensile testing, were further investigated using optical microscopy and scanning electron microscopy including electron backscatter diffraction.

Inorganic arsenic levels in baby rice are of concern

International Nuclear Information System (INIS)

Meharg, Andrew A.; Sun, Guoxin; Williams, Paul N.; Adomako, Eureka; Deacon, Claire; Zhu, Yong-Guan; Feldmann, Joerg; Raab, Andrea

2008-01-01

Inorganic arsenic is a chronic exposure carcinogen. Analysis of UK baby rice revealed a median inorganic arsenic content (n = 17) of 0.11 mg/kg. By plotting inorganic arsenic against total arsenic, it was found that inorganic concentrations increased linearly up to 0.25 mg/kg total arsenic, then plateaued at 0.16 mg/kg at higher total arsenic concentrations. Inorganic arsenic intake by babies (4-12 months) was considered with respect to current dietary ingestion regulations. It was found that 35% of the baby rice samples analysed would be illegal for sale in China which has regulatory limit of 0.15 mg/kg inorganic arsenic. EU and US food regulations on arsenic are non-existent. When baby inorganic arsenic intake from rice was considered, median consumption (expressed as μg/kg/d) was higher than drinking water maximum exposures predicted for adults in these regions when water intake was expressed on a bodyweight basis. - Median consumption of organic arsenic levels for UK babies from baby rice is above threshold considered safe

29 BABY DUMPING AND EVOLVING BABY FACTORIES IN NIGERIA

African Journals Online (AJOL)

room for a conducive environment for child rights and social protection. ... new dimensions to include the worst of all forms of human trafficking issues ... of strict penalties for offenders in the bid to give every child born the benefit of ..... vein, the study conducted by Onuoha (2014) listed the causes of baby factory incidences to.

Feeding Your Baby

Medline Plus

Full Text Available ... intensive care unit (NICU) Birth defects & other health conditions Loss & grief ... health of all moms and babies. We're advocating for policies to protect them. We're working to radically improve the health care they receive. ...

Mindful with Your Baby : Feasibility, Acceptability, and Effects of a Mindful Parenting Group Training for Mothers and Their Babies in a Mental Health Context

NARCIS (Netherlands)

Potharst, E.S.; Aktar, E.; Rexwinkel, M.; Rigterink, M.; Bögels, S.M.

2017-01-01

Many mothers experience difficulties after the birth of a baby. Mindful parenting may have benefits for mothers and babies, because it can help mothers regulate stress, and be more attentive towards themselves and their babies, which may have positive effects on their responsivity. This study

Experimental evaluation of emergency operating procedures on multiple steam generator tube rupture in INER integral system test facility

International Nuclear Information System (INIS)

Liu, T.J.; Lin, Y.M.; Lee, C.H.; Chang, C.Y.; Hong, W.T.

1997-01-01

The multiple steam generator tube rupture (SGTR) scenario in Westinghouse type pressurized water reactor (PWR) has been investigated at the Institute of Nuclear Energy Research (INER) Integral System Test (IIST) facility. This reduced-height and reduced-pressure test facility was designed to simulate the main features of Maanshan nuclear power plant. The SGTR test scenario assumes the double-ended break of one-, two- and six- tubes without other failures. The major operator actions follow the related symptom-oriented Emergency Operating Procedure (EOP) on the reference plant. This study focuses on the investigation of thermal-hydraulics phenomena and the adequacy of associated EOP to limit primary-to-secondary leakage. Through this study, it is found that the adequacy of current EOP in minimizing the radioactivity release demands early substantial operator involvement, especially in the multi-tubes break events. Also, the detailed mechanism of the main thermal-hydraulic phenomena during the SGTR transient are explored. (author)

The design of high vacuum system for baby electron beam machine (baby ebm): a comparison between theoretical and experimental

International Nuclear Information System (INIS)

Mohd Rizal Mamat; Rosli Darmawan; Lee Chee Huei; Mohd Rizal Md Chulan; Leo Kwee Wah; Muhamad Zahidee Taat; Fadzlie Nordin; Abu Bakar Mhd Ghazali

2005-01-01

Baby ebm which was developed to study the engineering and physics of electrons requires the use of high vacuum system in order to prevent electron loss and ionization of air molecules. In selecting the high vacuum system for baby ebm two main factors were considered: the ultimate pressure and the pump down time. The ultimate pressure required for the operation of the baby ebm is in 10-7 torr range. The pump down time was estimated from calculations, taking into account the vacuum pump and chamber size. The turbomolecular pump system (tmp), which is capable of achieving the required vacuum level was selected as the high vacuum system and installed to baby ebm. The tmp is currently fully operational. It was found that the vacuum pumping performance of the tmp differs considerably from what the calculations indicate. Compared to the calculations, it takes a much longer time to achieve the required operating pressure of baby ebm. This could be due to the fact that the formula used for the calculations was a very simplified formula that takes into account the main factors only which are the vacuum pump and chamber size. This paper attempts to present the comparison of the tmp performance between the theoretical and experimental. (Author)

Low hepatitis C antibody screening rates among an insured population of Tennessean Baby Boomers.

Directory of Open Access Journals (Sweden)

James G Carlucci

Full Text Available Chronic Hepatitis C Virus (HCV infection is common and can cause liver disease and death. Persons born from 1945 through 1965 ("Baby Boomers" have relatively high prevalence of chronic HCV infection, prompting recommendations that all Baby Boomers be screened for HCV. If chronic HCV is confirmed, evaluation for antiviral treatment should be performed. Direct-acting antivirals can cure more than 90% of people with chronic HCV. This sequence of services can be referred to as the HCV "cascade of cure" (CoC. The Tennessee (TN Department of Health (TDH and a health insurer with presence in TN aimed to determine the proportion of Baby Boomers who access HCV screening services and appropriately navigate the HCV CoC in TN.TDH surveillance data and insurance claim records were queried to identify the cohort of Baby Boomers eligible for HCV testing. Billing codes and pharmacy records from 2013 through 2015 were used to determine whether HCV screening and other HCV-related services were provided. The proportion of individuals accessing HCV screening and other steps along the HCV CoC was determined. Multivariable analyses were performed to identify factors associated with HCV screening and treatment.Among 501,388 insured Tennessean Baby Boomers, 7% were screened for HCV. Of the 40,019 who received any HCV-related service, 86% were screened with an HCV antibody test, 20% had a confirmatory HCV PCR, 9% were evaluated for treatment, and 4% were prescribed antivirals. Hispanics were more likely to be screened and treated for HCV than non-Hispanic whites. HCV screening was more likely to occur in the Nashville-Davidson region than in other regions of TN, but there were regional variations in HCV treatment.Many insured Tennessean Baby Boomers do not access HCV screening services, despite national recommendations. Demographic and regional differences in uptake along the HCV CoC should inform public health interventions aimed at mitigating the effects of chronic

Pressure tube rupture in a closed tank

International Nuclear Information System (INIS)

Khater, H.A.; Hadaller, G.I.; Stern, F.

1985-06-01

A study has been prepared on the feasibility of conducting pressure tube/calandria tube rupture tests in a closed tank, simulating a scaled-down calandria vessel. The study includes: i) a review of previous work, ii) an analytical investigation of the scaling problem of the calandria vessel and relevant in-core structures, iii) selection of a method for initiating pressure tube/calandria tube rupture, iv) a set of specifications for the test assembly, v) general arrangement drawings, vi) a proposal for a test matrix, vii) a survey and evaluation of existing facilities which could provide the required high pressure, temperature and fluid inventory, and viii) a cost estimate for the detailed design and construction, instrumentation, data acquisition and reduction, testing and reporting. The study concludes that it is both technically and practically feasible to conduct pressure tube rupture tests in a closed tank

Feeding Your Baby

Medline Plus

Full Text Available ... Global Map Premature Birth Report Cards Careers Archives Pregnancy Before or between pregnancies Nutrition, weight & fitness Prenatal care Is it safe? ... Feeding your baby Family health & safety Complications & Loss Pregnancy complications Preterm labor & premature birth The newborn intensive ...

Predictive modelling for shelf life determination of nutricereal based fermented baby food.

Science.gov (United States)

Rasane, Prasad; Jha, Alok; Sharma, Nitya

2015-08-01

A shelf life model based on storage temperatures was developed for a nutricereal based fermented baby food formulation. The formulated baby food samples were packaged and stored at 10, 25, 37 and 45 °C for a test storage period of 180 days. A shelf life study was conducted using consumer and semi-trained panels, along with chemical analysis (moisture and acidity). The chemical parameters (moisture and titratable acidity) were found inadequate in determining the shelf life of the formulated product. Weibull hazard analysis was used to determine the shelf life of the product based on sensory evaluation. Considering 25 and 50 % rejection probability, the shelf life of the baby food formulation was predicted to be 98 and 322 days, 84 and 271 days, 71 and 221 days and 58 and 171 days for the samples stored at 10, 25, 37 and 45 °C, respectively. A shelf life equation was proposed using the rejection times obtained from the consumer study. Finally, the formulated baby food samples were subjected to microbial analysis for the predicted shelf life period and were found microbiologically safe for consumption during the storage period of 360 days.

Effect on skin hydration of using baby wipes to clean the napkin area of newborn babies: assessor-blinded randomised controlled equivalence trial.

Science.gov (United States)

Lavender, Tina; Furber, Christine; Campbell, Malcolm; Victor, Suresh; Roberts, Ian; Bedwell, Carol; Cork, Michael J

2012-06-01

Some national guidelines recommend the use of water alone for napkin cleansing. Yet, there is a readiness, amongst many parents, to use baby wipes. Evidence from randomised controlled trials, of the effect of baby wipes on newborn skin integrity is lacking. We conducted a study to examine the hypothesis that the use of a specifically formulated cleansing wipe on the napkin area of newborn infants (skin hydration when compared with using cotton wool and water (usual care). A prospective, assessor-blinded, randomised controlled equivalence trial was conducted during 2010. Healthy, term babies (n=280), recruited within 48 hours of birth, were randomly assigned to have their napkin area cleansed with an alcohol-free baby wipe (140 babies) or cotton wool and water (140 babies). Primary outcome was change in hydration from within 48 hours of birth to 4 weeks post-birth. Secondary outcomes comprised changes in trans-epidermal water loss, skin surface pH and erythema, presence of microbial skin contaminants/irritants at 4 weeks and napkin dermatitis reported by midwife at 4 weeks and mother during the 4 weeks. Complete hydration data were obtained for 254 (90.7 %) babies. Wipes were shown to be equivalent to water and cotton wool in terms of skin hydration (intention-to-treat analysis: wipes 65.4 (SD 12.4) vs. water 63.5 (14.2), p=0.47, 95% CI -2.5 to 4.2; per protocol analysis: wipes 64.6 (12.4) vs. water 63.6 (14.3), p=0.53, 95% CI -2.4 to 4.2). No significant differences were found in the secondary outcomes, except for maternal-reported napkin dermatitis, which was higher in the water group (p=0.025 for complete responses). Baby wipes had an equivalent effect on skin hydration when compared with cotton wool and water. We found no evidence of any adverse effects of using these wipes. These findings offer reassurance to parents who choose to use baby wipes and to health professionals who support their use. Current Controlled Trials ISRCTN86207019.

A Simple Test Tube-Based ELISA Experiment for the High-School Classroom*

Science.gov (United States)

Brokaw, Ann; Cobb, Brian A.

2010-01-01

Immunology is gaining prominence both in the media as well as on the Advanced Placement (AP) exam in Biology. One of the challenges of teaching modern biological topics such as immunology and biochemistry in the high-school setting is the increased reliance on expensive technology in the research world. To begin to bridge this widening gap, we devised an experiment using a novel macroscale enzyme-linked immunosorbent assay that is suitable for AP-level high-school biology classrooms as well as entry-level collegiate laboratories. This novel method does not require a plate reader for data analysis, but instead relies on more common and inexpensive equipment such as a clinical test tube centrifuge and a simple test tube spectrophotometer. The experimental plan focuses on students measuring antibody concentrations in “unknown” samples and includes the collection and analysis of a standard curve using reagents prepared by the instructor. Students will be introduced to enzyme action, quantitative laboratory technique, antibodies, and the immune system, with the overall goal being to explore and highlight the inherent connections within the fields of biochemistry and immunology. PMID:20689684

MONITORING BABY INCUBATOR SENTRAL DENGAN KOMUNIKASI WIRELESS

Directory of Open Access Journals (Sweden)

Ary Sulistyo Utomo

2018-04-01

180m. Pengujian suhu ruang baby incubator menggunakan termometer sebagai perbandingan dengan nilai suhu yang dibaca pada alat. Dari pengukuran diperoleh tingkat perbedaan 0% pada suhu 30oC dan 2,8% pada suhu 37oC.   Kata kunci: baby incubator, sistem monitoring sentral, microsoft visual studio, arduino.

Measurement of the viscoelastic compliance of the eustachian tube using a modified forced-response test.

Science.gov (United States)

Ghadiali, Samir N; Federspiel, William J; Swarts, J Douglas; Doyle, William J

2002-01-01

Eustachian tube compliance (ETC) was suggested to be an important determinate of function. Previous attempts to quantify ETC used summary measures that are not clearly related to the physical properties of the system. Here, we present a new method for measuring ETC that conforms more closely to the engineering definition of compliance. The forced response test was modified to include oscillations in applied flow after the forced tubal opening. Pressure and flow were recorded during the standard and modified test in 12 anesthetized cynomolgus monkeys. The resulting pressure-flow, hysteresis loops were compared with those predicted by a simple fluid-structure model of the Eustachian tube with linear-elastic or viscoelastic properties. The tubal compliance index (TCI) and a viscoelastic compliance (C(v)) were calculated from these data for each monkey. The behavior of a viscoelastic, but not a linear elastic model accurately reproduced the experimental data for the monkey. The TCI and C(v) were linearly related, but the shared variance in these measures was only 63%. This new method for measuring ETC captures all information contained in the traditional TCI, but also provides information regarding the contribution of wall viscosity to Eustachian tube mechanics.

[Attachment theory and baby slings/carriers: technological network formation].

Science.gov (United States)

Lu, Zxy-Yann Jane; Lin, Wan-Shiuan

2011-12-01

Healthcare providers recognize the important role played by attachment theory in explaining the close relationship between mental health and social behavior in mothers and their children. This paper uses attachment theory in a socio-cultural context to ascertain the mechanism by which baby slings/carriers, a new technology, produced and reproduced the scientific motherhood. It further applies a social history of technology perspective to understand how baby carriers and attachment theory are socially constructed and historically contingent on three major transformations. These transformations include the use of attachment theory-based baby carriers to further scientific motherhood; the use of baby slings/carriers to further the medicalization of breastfeeding and enhance mother-infant attachment; and the use of baby slings/carriers to transform woman's identities by integrating scientific motherhood, independence and fashion. Implications for nursing clinical policy are suggested.

Baby MIND Experiment Construction Status

Energy Technology Data Exchange (ETDEWEB)

Antonova, M.; et al.

2017-04-28

Baby MIND is a magnetized iron neutrino detector, with novel design features, and is planned to serve as a downstream magnetized muon spectrometer for the WAGASCI experiment on the T2K neutrino beam line in Japan. One of the main goals of this experiment is to reduce systematic uncertainties relevant to CP-violation searches, by measuring the neutrino contamination in the anti-neutrino beam mode of T2K. Baby MIND is currently being constructed at CERN, and is planned to be operational in Japan in October 2017.

Failure of fretted steam generator tubes under accident conditions

International Nuclear Information System (INIS)

Forrest, C.F.

1996-10-01

Tests were carried out with a bank of tubes in a water tunnel to determine the tolerance of flawed nuclear reactor steam generator tubes to accident conditions which would result in high cross-flow velocities. Fourteen specimen tubes were tested, each having one or two types of defect machined into the surface simulating fretting-wear type scars found in some operating steam generators. The tubes were tested at flow velocities sufficient to induce high fluid elastic-type vibrations. Seven of the tubes failed near the thinnest section of the defects during the one-hour tests, due to impacting and/or rubbing between the tube and the support. Strain gauges, displacement transducers, force gauges and an accelerometer were used on the target tube and/or the tube immediately downstream of it to measure their vibrational characteristics

Standard practice for ultrasonic testing of the Weld Zone of welded pipe and tubing

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 This practice describes general ultrasonic testing procedures for the detection of discontinuities in the weld and adjacent heat affected zones of welded pipe and tubing by scanning with relative motion between the search unit and pipe or tube. When contact or unfocused immersion search units are employed, this practice is intended for tubular products having specified outside diameters ≥2 in. (≥50 mm) and specified wall thicknesses of 1/8to 11/16 in. (3 to 27 mm). When properly focused immersion search units are employed, this practice may also be applied to material of smaller diameter and thinner wall. Note 1—When contact or unfocused immersion search units are used, precautions should be exercised when examining pipes or tubes near the lower specified limits. Certain combinations of search unit size, frequency, thin–wall thicknesses, and small diameters could cause generation of unwanted sound waves that may produce erroneous examination results. 1.2 All surfaces of material to be examined in ...

Birthing Healthy Babies (A Cup of Health with CDC)

Centers for Disease Control (CDC) Podcasts

2018-01-11

Every four and a half minutes a baby is born with a birth defect in the United States. That means nearly 120,000 babies, or about three percent of all babies born each year. In this podcast, Dr. Suzanne Gilboa discusses ways to prevent birth defects.  Created: 1/11/2018 by MMWR.   Date Released: 1/11/2018.

Designer Babies: Eugenics Repackaged or Consumer Options?

Science.gov (United States)

Baird, Stephen L.

2007-01-01

"Designer babies" is a term used by journalists and commentators--not by scientists--to describe several different reproductive technologies. These technologies have one thing in common: they give parents more control over what their offspring will be like. Designer babies are made possible by progress in three fields: (1) Advanced…

FY 1997 Progress report on tube propagation testing of tank waste using the PRSST

International Nuclear Information System (INIS)

Bechtold, D.B.

1997-01-01

The subject of this FY 1997 progress report is tube propagation tests of actual, dried tank waste to verify the contact temperature ignition (CTI) criterion for point-source ignition in the Hanford Site waste tanks. Testing is in support of the Organic Tanks Safety Project and will help resolve safety issues with waste containing organic constituents. In FY 1997, improvements were made to the laboratory apparatus and procedures for conducting the testing, and the final testing strategy was formulated. The strategy lays out details of the tests to be performed, samples to be tested, and modes of reporting results

Feeding Your Baby

Medline Plus

Full Text Available ... Product Catalog Volunteer Volunteer leaders Team Youth National service partners ... strong. It’s also a great time for you and your partner to bond with her. Breast milk is the best food for your baby during the first year of ...

Ice, Ice, Baby!

Science.gov (United States)

Hamilton, C.

2008-12-01

The Center for Remote Sensing of Ice Sheets (CReSIS) has developed an outreach program based on hands-on activities called "Ice, Ice, Baby". These lessons are designed to teach the science principles of displacement, forces of motion, density, and states of matter. These properties are easily taught through the interesting topics of glaciers, icebergs, and sea level rise in K-8 classrooms. The activities are fun, engaging, and simple enough to be used at science fairs and family science nights. Students who have participated in "Ice, Ice, Baby" have successfully taught these to adults and students at informal events. The lessons are based on education standards which are available on our website www.cresis.ku.edu. This presentation will provide information on the activities, survey results from teachers who have used the material, and other suggested material that can be used before and after the activities.

Online in-tube microextractor coupled with UV-Vis spectrophotometer for bisphenol A detection.

Science.gov (United States)

Poorahong, Sujittra; Thammakhet, Chongdee; Thavarungkul, Panote; Kanatharana, Proespichaya

2013-01-01

A simple and high extraction efficiency online in-tube microextractor (ITME) was developed for bisphenol A (BPA) detection in water samples. The ITME was fabricated by a stepwise electrodeposition of polyaniline, polyethylene glycol and polydimethylsiloxane composite (CPANI) inside a silico-steel tube. The obtained ITME coupled with UV-Vis detection at 278 nm was investigated. By this method, the extraction and pre-concentration of BPA in water were carried out in a single step. Under optimum conditions, the system provided a linear dynamic range of 0.1 to 100 μM with a limit of detection of 20 nM (S/N ≥3). A single in-tube microextractor had a good stability of more than 60 consecutive injections for 10.0 μM BPA with a relative standard deviation of less than 4%. Moreover, a good tube-to-tube reproducibility and precision were obtained. The system was applied to detect BPA in water samples from six brands of baby bottles and the results showed good agreement with those obtained from the conventional GC-MS method. Acceptable percentage recoveries from the spiked water samples were obtained, ranging from 83-102% for this new method compared with 73-107% for the GC-MS standard method. This new in-tube CPANI microextractor provided an excellent extraction efficiency and a good reproducibility. In addition, it can also be easily applied for the analysis of other polar organic compounds contaminated in water sample.

Water-storage-tube systems. Final report

Energy Technology Data Exchange (ETDEWEB)

Hemker, P.

1981-12-24

Passive solar collection/storage/distribution systems were surveyed, designed, fabricated, and mechanically and thermally tested. The types studied were clear and opaque fiberglass tubes, metal tubes with plastic liners, and thermosyphoning tubes. (MHR)

Definition of the minimum longitude of insert in the rebuilding of Charpy test tubes for surveillance and life extension of vessels in Mexico

International Nuclear Information System (INIS)

Romero C, J.; Hernandez C, R.; Rocamontes A, M.

2011-11-01

In the National Institute of Nuclear Research (Mexico) a welding system for the rebuilding of Charpy test tubes has been developed, automated, qualified and used for the surveillance of the mechanical properties (mainly embrittlement) of the vessel. This system uses the halves of the rehearsed Charpy test tubes of the surveillance capsules extracted of the reactors, to obtain, of a rehearsed test tube, two reconstituted test tubes. This rebuilding process is used so much in the surveillance program like in the potential extension of the operation license of the vessel. To the halves of Charpy test tubes that have been removed the deformed part by machine are called -insert- and in a very general way the rebuilding consists in weld with the welding process -Stud Welding- two metallic implants in the ends of the insert, to obtain a reconstituted test tube. The main characteristic of this welding are the achieved small dimensions, so much of the areas welded as of the areas affected by the heat. The applicable normative settles down that the minim longitude of the insert for the welding process by Stud Welding it should be of 18 mm, however according to the same normative this longitude can diminish if is demonstrated analytic or experimentally that the central volume of 1 cm 3 in the insert is not affected. In this work the measurement of the temperature profiles to different distances of the welding interface is presented, defining an equation for the maximum temperatures reached in function of the distance, on the other hand the real longitude affected in the test tube by means of metallography is determined and this way the minimum longitude of the insert for this developed rebuilding system was determined. (Author)

Vibration characteristics of tubes in a heat exchanger

International Nuclear Information System (INIS)

Simonis; Steininger, D.

1985-01-01

Circumferential tube cracking has occurred in the once-through steam generators used in nuclear power plants. Analyses of failed tubes indicate that a fatigue process induced by tube vibration could cause the leaks. To investigate the vibration amplitude of tube spans during reactor operation, twenty-three tube spans were instrumented with accelerometers and strain gages at Three Mile Island Unit 2. To aid in the interpretation of the operational vibration measurements, tests were performed, in air, to determine the predominant resonant frequencies and mode shapes of selected tubes. By adapting modal analysis techniques, the two predominant response frequencies were determined for 100 randomly selected tube spans and the 23 instrumented tube spans; plus, the predominant mode shape was determined for five tube spans bounded by the tube sheet and the fifteenth support plate and one tube span bounded by the ninth and tenth support plate. The average value for the first and second predominant response frequency was 65 Hz and 170 Hz, respectively. The predominant frequencies for the individual tube spans are distributed randomly with no spatial orientation. The first predominant mode shape for the six tube spans tested corresponded to a classical beam with elastic supports. The equivalent stiffness of the elastic supports depend upon the tube span tested

Gender specific intrapartum and neonatal outcomes for term babies.

Science.gov (United States)

Dunn, Liam; Prior, Tomas; Greer, Ristan; Kumar, Sailesh

2015-02-01

The purpose of this study is to document the gender specific intrapartum and neonatal outcomes in term, singleton, appropriately grown babies. De-identified, routinely collected data of all women meeting inclusion criteria between 2001 and 2011 were examined (n=9223). Inclusion criteria were public (non-insured), primiparous women who had delivered singleton, appropriately grown babies at term. In this retrospective cohort study, we estimated 95% confidence intervals. Outcomes measured were maternal demographics, mode of delivery, birthweight, APGAR score, cord blood acidemia, respiratory distress, any resuscitation requirement, nursery admission and stillbirth rates. The sex ratio of male babies was 1.05:1 (4718 males; 4505 females, p=0.85). Male babies were more likely to be delivered by instrumental (p=0.004) or caesarean (pinfluencing factor on mode of delivery. Even after adjusting for birthweight, male babies were more likely to be delivered by instrumental delivery (OR 1.24, pgender may play an independent role in influencing pregnancy outcomes, although the underlying contributing physiology is not definitively established. The gender of the baby perhaps should be considered when counselling parents in the antepartum period. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Does the gestation age of newborn babies influence the ultrasonic assessment of hip condition?

Directory of Open Access Journals (Sweden)

Simić Slavica

2009-01-01

Full Text Available Introduction. Ultrasound represents a method of examination of hips of newborn babies capable of defining hip condition and distinguishing stable and unstable hips based on morphological elements. It is accepted in a large number of countries as a method of examination of high risk newborns, or as a method of systematic screening. Objective. The objective of this study was to investigate correlation between ultrasonically estimated hip maturity and respective gestation maturity both in premature and term-born babies, and to investigate the influence of different delivery types on hips condition. Methods. In our study 2045 patients, 1141 males and 904 females, were examined in at the Institute of Neonatology over a period of 5 years. The average age was 34.04 gestation weeks. There were significantly more premature (1698 or 83.03% than term-born babies (347 or 16.97%. Ultrasound hip examination, as a screening method, was carried out according to Graf. It was followed by clinical examination. Results were analyzed by appropriate statistical methods (χ2-test, one-way ANOVA, multifactor ANOVA. Results. The overall frequency of unstable hips was 3.2%, 1.88% in males and 4.87% in females (p<0.05. 96.8% babies had stable hips, out of which 35.21% were mature and 61.59% immature. In the study of the breech presentation, out of 183 babies, unstable hips were found in 1.58% of male cases, and in 10.23% of female cases. Conclusion. Clinical screening of developmental dysplasia of the hip is insufficient for early diagnosis and decision about the treatment of premature babies. The high frequency of unstable hip type IIc (risky and IId (decentralized in premature babies requires early diagnosis and therapy. Wide swaddling for prematures should be applied up to eight months of age. Gentle manipulation is necessary while nursing and conducting physiotherapy of a premature baby.

Teen Moms and Babies Benefit from Camping.

Science.gov (United States)

Goode, Marsha; Broesamle, Barbara

1987-01-01

Describes nine-day residential camp for Michigan teenage mothers/babies to enhance personal growth and develop responsible social skills. Outlines goals, pre-camp planning, staff, activities, evaluation. Reports 31 teen moms (ages 13-21) and 35 babies attended in 1986. Indicates participants were in therapy, experienced abuse, had low self-esteem,…

The Dried Bloodspot: Newborn Screening Research Saving the Lives of Babies

Science.gov (United States)

Levy-Fisch, Jill; Gartzke, Micki; Leight, Kelly

2010-01-01

Newborn screening is a test done on every child born in the US shortly after birth to detect diseases where, if not diagnosed and treated in the newborn period, the child will suffer significant trauma, disability or die. A few drops of blood from each baby's heel is put on a card and sent to the state's public health lab for testing. Most states…

Tensile properties of quadruple melted Zr-2.5Nb pressure tubes evaluated from pressure tube offcuts

International Nuclear Information System (INIS)

Shah, Priti Kotak; Dubey, J.S.; Anantharaman, S.

2013-12-01

Rajasthan Atomic Power Station-2 (RAPS-2) is the first Pressurised Heavy Water Reactor (PHWR) in India having quadruple melted Zr-2.5Nb pressure tubes. Front-end and back-end off-cuts of sixteen pressure tubes were selected for studying the mechanical properties in axial and transverse directions of the tube. Tension tests were carried out at room temperature and at 300℃ using miniature tensile test specimens. The report presents the experimental details and discusses the base line tensile property data for the quadruple melted pressure tubes of RAPS-2. This data will be useful for the reactor life management. (author)

Non-destructive testing of high pressure fibre reinforced composites tubes by computed tomography

Energy Technology Data Exchange (ETDEWEB)

Klimek, L. [Qualitaetszentrum Dortmund (Germany); Monstadt, H.; Boedecker, T. [EFMT, Bochum (Germany)

1995-12-31

For new applications of fibre reinforced composites, new non-destructive testing methods are required which on the one hand can be used as a quality testing method and on the other hand as an in-service inspection method during the life of a product. Special attention should be paid to the defect sensitivity and to a detailed classification of visible defects. Defining a detectable standard, comparable investigations were carried out using the Ultra Fast Scanner which is located at the Entwicklungs- und Forschungszentrum fuer Mikrotherapie gGmbH (EFMT) and the industrial scanner of the Qualitaetszentrum Dortmund GmbH u. Co. KG (QZ-DO). The investigation object is a high pressure tube which is made up of three different diameter structures. There can be distinguished between three types of tube layers. Digital image processing has been used to get more information form measured data. We developed two different types of digital image filters: A SIGMA and a Contrast Sensitive Weights (CSW) image filter and made a comparative study. (orig./RHM)

Development of zirconium alloy tube manufacturing technology

International Nuclear Information System (INIS)

Kim, In Kyu; Park, Chan Hyun; Lee, Seung Hwan; Chung, Sun Kyo

2009-01-01

In late 2004, Korea Nuclear Fuel Company (KNF) launched a government funded joint development program with Westinghouse Electric Co. (WEC) to establish zirconium alloy tube manufacturing technology in Korea. Through this program, KNF and WEC have developed a state of the art facility to manufacture high quality nuclear tubes. KNF performed equipment qualification tests for each manufacturing machine with the support of WEC, and independently carried out product qualification tests for each tube product to be commercially produced. Apart from those tests, characterization test program consisting of specification test and characterization test was developed by KNF and WEC to demonstrate to customers of KNF the quality equivalency of products manufactured by KNF and WEC plants respectively. As part of establishment of performance evaluation technology for zirconium alloy tube in Korea, KNF carried out analyses of materials produced for the characterization test program using the most advanced techniques. Thanks to the accomplishment of the development of zirconium alloy tube manufacturing technology, KNF is expected to acquire positive spin off benefits in terms of technology and economy in the near future

Experiments on vibration of heat exchanger tube arrays in cross flow

International Nuclear Information System (INIS)

Blevins, R.D.; Gibert, R.J.; Villard, B.

1981-08-01

A series of tests have been made at the Commissariat a l'Energie Atomique, in cooperation with General Atomic Company, SAN DIEGO (U.S.A.) on the flow-induced vibration of heat exchanger tube bundles in cross flow. These tests were made in air on tube bundles which simulated heat exchangers in the high temperature gas cooled reactors. The tests were of two types. In the first type, an instrumented tube was inserted at various locations into a tube bundle. Measurements were made of pressure at a number of points along the tube and about the circumference of the tube. These measurements were processed to obtain the spectra of turbulent pressure fluctuations on the tube, the spanwise correlation and the lift force. The second set of tests was made on tube bundles with flexible tubes. As the flow velocity was increased, these tests clearly show an instability. Nine tube configurations were tested with both plastic and metallic tubes and the effect of tube-to-tube difference in natural frequency was investigated

Feeding Your Baby

Medline Plus

Full Text Available ... mail was sent. Save to my dashboard Sign in or Sign up to save this page. Saving Just a moment, please. You've saved this page It's been added to your dashboard . Time to eat! Feeding your baby helps her grow ...

Performance test results of mock-up model test facility with a full-scale reaction tube for HTTR hydrogen production system. Contract research

Energy Technology Data Exchange (ETDEWEB)

Inagaki, Yoshiyuki; Hayashi, Koji; Kato, Michio [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment] [and others

2003-03-01

Research on a hydrogen production system by steam reforming of methane, chemical reaction; CH{sub 4} + H{sub 2}O {yields} 3H{sub 2}O + CO, has been carried out to couple with the HTTR for establishment of high-temperature nuclear heat utilization technology and contribution to hydrogen energy society in future. The mock-up test facility with a full-scale reaction tube test facility, a model simulating one reaction tube of a steam reformer of the HTTR hydrogen production system in full scale, was fabricated to perform tests on controllability, hydrogen production performance etc. under the same pressure and temperature conditions as those of the HTTR hydrogen production system. The design and fabrication of the test facility started from 1997, and the all components were installed until September in 2001. In a performance test conducted from October in 2001 to February in 2002, performance of each component was examined and hydrogen of 120m{sup 3}{sub N}/h was successfully produced with high-temperature helium gas. This report describes the performance test results on components performance, hydrogen production characteristics etc., and main troubles and countermeasures. (author)

Performance test results of mock-up model test facility with a full-scale reaction tube for HTTR hydrogen production system. Contract research

International Nuclear Information System (INIS)

Inagaki, Yoshiyuki; Hayashi, Koji; Kato, Michio

2003-03-01

Research on a hydrogen production system by steam reforming of methane, chemical reaction; CH 4 + H 2 O → 3H 2 O + CO, has been carried out to couple with the HTTR for establishment of high-temperature nuclear heat utilization technology and contribution to hydrogen energy society in future. The mock-up test facility with a full-scale reaction tube test facility, a model simulating one reaction tube of a steam reformer of the HTTR hydrogen production system in full scale, was fabricated to perform tests on controllability, hydrogen production performance etc. under the same pressure and temperature conditions as those of the HTTR hydrogen production system. The design and fabrication of the test facility started from 1997, and the all components were installed until September in 2001. In a performance test conducted from October in 2001 to February in 2002, performance of each component was examined and hydrogen of 120m 3 N /h was successfully produced with high-temperature helium gas. This report describes the performance test results on components performance, hydrogen production characteristics etc., and main troubles and countermeasures. (author)

WWER Steam Generators Tubing Performance and Aging Management

International Nuclear Information System (INIS)

Trunov, Nikolay B.; Davidenko, Stanislav E.; Grigoriev, Vladimir A.; Popadchuk, Valery S.; Brykov, Sergery I.; Karzov, Georgy P.

2006-01-01

At WWER NPPs the horizontal steam generators (SGs), are used that differ in design concept from vertical SGs mostly used at western NPPs. Reliable operation of SG heat-exchanging tubes is the crucial worldwide problem for NPP of various types. According to the operation feedback the water chemistry is the governing factor affecting operability of SG tubing. The secondary side corrosion is considered to be the main mechanism of SG heat-exchanging tubes damage at WWER plants. To make the assessment of the tubing integrity the combination of pressure tests and eddy-current tests is used. Assessment of the tubing performance is an important part of SG life extension practice. The given paper deals with the description of the tube testing strategy and the approach to tube integrity assessment based on deterministic and probabilistic methods of fracture mechanics. Requirements for eddy-current test are given as well. Practice of condition monitoring and implementing the database on steam generators operation are presented. The approach to tubes plugging criteria is described. The research activities on corrosion mechanism studies and residual lifetime evaluation are mentioned. (authors)

Baby Skyrme models for a class of potentials

International Nuclear Information System (INIS)

Eslami, P.; Zakrzewski, W.; Sarbishaei, M.

2000-01-01

We consider a class of (2+1)- dimensional baby Skyrme models with potentials that have more than one vacuum. These potentials are generalizations of old and new baby Skyrme models; they involve more complicated dependence on φ 3 . We find that when the potential is invariant under φ 3 → -φ 3 the configurations corresponding to the baby Skyrmions lying 'on top of each other' are the minima of the energy. However, when the potential breaks this symmetry the lowest field configurations correspond to separated baby skyrmions. We compute the energy distributions for skyrmions of degrees between one and eight and discuss their geometrical shapes and binding energies. We also compare the 2-skyrmion states for these potentials. Most of our work has been performed numerically with the model being formulated in terms of three real scalar fields (satisfying one constraint)

Code Assessment of SPACE 2.19 using LSTF Steam Generator Tube Rupture Test

Energy Technology Data Exchange (ETDEWEB)

Kim, Minhee; Kim, Seyun [KHNP CRI, Daejeon (Korea, Republic of)

2016-10-15

The SPACE is a best estimated two-phase three-field thermal-hydraulic analysis code used to analyze the safety and performance of pressurized water reactors. As a result of the development, the 2.19 version of the code was released through the successive various verification and validation works. The present work is on the line of expanding the work by Kim et al. In this study, results produced by the SPACE 2.19 code were compared with the experimental data from JAERI's LSTF Test Run LSTF SB-SG-06 experiment simulating a Steam Generator Tube Rupture (SGTR) transient. In order to identify the predictability of SPACE 2.19, the LSTF steam generator tube rupture test was simulated. To evaluate the computed results, LSTF SB-SG-06 test data simulating the SGTR and the RELAP5/ MOD3.1 are used. The calculation results indicate that the SPACE 2.19 code predicted well the sequence of events and the major phenomena during the transient, such as the asymmetric loop behavior, reactor coolant system cooldown and heat transfer by natural circulation, the primary and secondary system depressurization by the pressurizer auxiliary spray and the steam dump using the intact loop steam generator relief valve.

Nondestructive inspection of the tubes of TRIGA IPR-R1 reactor heat exchanger by eddy current testing

International Nuclear Information System (INIS)

Silva Junior, Silverio F.; Silva, Roger F.; Oliveira, Paulo F.; Barreto, Erika S.; Ribeiro, Isabela G.; Fraiz, Felipe C.

2013-01-01

The IPR-R1 TRIGA MARK 1 reactor is an open pool type reactor, cooled light water. It is used for research activities, personnel training and radioisotopes production, in operation since 1960 at the Nuclear Technology Development Center - CDTN/CNEN. It operates at a maximum thermal power of 100 kW and usually, the fuel cooling is done by natural circulation. If necessary, an external auxiliary cooling system, with a shell-and-tube type heat exchanger, can be used to improve the water heat removal. As part of the ageing management program of the reactor, a nondestructive evaluation of their heat exchanger stainless steel tubes will be performed, in order to verify its integrity. The examinations will be performed using the eddy current test method, which allows the detection and characterization of structural discontinuities in the wall of the tubes, if existing. For this purpose, probes and reference standards were designed and manufactured at CDTN facilities and test procedures were established and validated. In this paper, a description of the proposed infrastructure as well as the test methodology to be used in the examinations are presented and discussed. (author)

DHC velocity comparison of CANDU Zr-2.5Nb pressure tube for the difference of test environments

International Nuclear Information System (INIS)

Cho, S. Y.; Kim, Y. S.; Oh, D. Z.; Yim, K. S.; Yim, Y. W.

2001-01-01

Zr-2.5Nb Pressure tube was used in the distilled water under high temperature and pressure. However, the evaluation of DHCV for pressure tube was limited in the air until now. Therefore, it was necessary for DHCV both in the air and in the distilled water under high temperature and pressure to evaluate. In advance, new DHC equipment simulating the real operating condition in the distilled water under high temperature and pressure was developed and DHCV test was conducted by this equipment. The test was carried out under simulated condition using distilled water of 250 .deg. C, 86bar and this result was compared with of DHCV in the air of 250 .deg. C. DHCV of the distilled water was ranged from 8.42x10 -8 to 9.92x 10 -8 m/s and the average value was 9.01x 10 -8 m/s. As compared with the air condition, it was found that characteristics of DHCV was not affected by the distilled water of high temperature and pressure. At the same temperature, DHCV of the irradiated pressure tube was faster than that of test result

Kangaroo Mother Care Management of a 750 Ggrammes Baby: A ...

African Journals Online (AJOL)

This paper presents the successful management of 750 grammes low birth weight baby using kangaroo mother care in the hospital and at home. The baby had suffered a variety of morbidities associated with prematurity in the early neonatal period. Key words: Kangaroo mother care, low birth weight babies ...

Is the ABC pain scale reliable for premature babies?

Science.gov (United States)

Bellieni, Cv; Maffei, M; Ancora, G; Cordelli, D; Mastrocola, M; Faldella, G; Ferretti, E; Buonocore, G

2007-07-01

We recently developed the ABC scale to assess pain in term newborns. The aim of the present study was to assess the reliability of the scale in preterm babies. The scale consists of three cry parameters: (a) pitch of the first cry, (b) rhythmicity of the bout of crying and (c) cry constancy. Changes in these parameters were previously found to distinguish medium and high levels of pain as evaluated by spectral analysis of crying. We enrolled 72 babies to perform the steps usually requested to validate a scale, namely the study of the concurrent validity, specificity and sensibility. Moreover, we assessed the interjudge reliability and the clinical utility and ease of the scale. A good correlation (r = 0.68; r(2)= 0.45; p babies who underwent pain and babies who underwent non-painful stimulus.) Interobserver reliability was good: Cohen's kappa = 0.7. The good correlation between the two scales shows that the ABC scale is also reliable for premature babies.

Effect on skin hydration of using baby wipes to clean the napkin area of newborn babies: assessor-blinded randomised controlled equivalence trial

Directory of Open Access Journals (Sweden)

Lavender Tina

2012-06-01

Full Text Available Abstract Background Some national guidelines recommend the use of water alone for napkin cleansing. Yet, there is a readiness, amongst many parents, to use baby wipes. Evidence from randomised controlled trials, of the effect of baby wipes on newborn skin integrity is lacking. We conducted a study to examine the hypothesis that the use of a specifically formulated cleansing wipe on the napkin area of newborn infants ( Methods A prospective, assessor-blinded, randomised controlled equivalence trial was conducted during 2010. Healthy, term babies (n = 280, recruited within 48 hours of birth, were randomly assigned to have their napkin area cleansed with an alcohol-free baby wipe (140 babies or cotton wool and water (140 babies. Primary outcome was change in hydration from within 48 hours of birth to 4 weeks post-birth. Secondary outcomes comprised changes in trans-epidermal water loss, skin surface pH and erythema, presence of microbial skin contaminants/irritants at 4 weeks and napkin dermatitis reported by midwife at 4 weeks and mother during the 4 weeks. Results Complete hydration data were obtained for 254 (90.7 % babies. Wipes were shown to be equivalent to water and cotton wool in terms of skin hydration (intention-to-treat analysis: wipes 65.4 (SD 12.4 vs. water 63.5 (14.2, p = 0.47, 95 % CI -2.5 to 4.2; per protocol analysis: wipes 64.6 (12.4 vs. water 63.6 (14.3, p = 0.53, 95 % CI -2.4 to 4.2. No significant differences were found in the secondary outcomes, except for maternal-reported napkin dermatitis, which was higher in the water group (p = 0.025 for complete responses. Conclusions Baby wipes had an equivalent effect on skin hydration when compared with cotton wool and water. We found no evidence of any adverse effects of using these wipes. These findings offer reassurance to parents who choose to use baby wipes and to health professionals who support their use. Trial registration Current Controlled

Vibration tests on single heat exchanger tubes in air and static water

International Nuclear Information System (INIS)

Collinson, A.E.; Warneford, I.P.

1978-07-01

The vibrational characteristics of a 7 span straight tube and a 26 span U-tube have been investigated for the effects of fluid medium (air/water), tube-grid clearance, tube-grid contact force, vibration transmission and scale. Measured frequency response and mode shapes compared favourably with theoretical values, vibration with pin-pin tube support being most readily excited. The frequency reduction on immersion in water corresponded to an added mass equivalent to the liquid displaced mass. Dynamic magnifiers varied in the range 12 to 135 with mean values of 30 to 40 in water and 45 to 60 in air. Principal vibration modes and damping values were reproducible in a half-scale model of a U-tube. (author)

Motor Development Programming in Trisomic-21 Babies

Science.gov (United States)

Sanz, Teresa; Menendez, Javier; Rosique, Teresa

2011-01-01

The present study contributes to the understanding of gross motor development in babies with Down's syndrome. Also, it facilitates the comprehension of the efficiency of the early motor stimulation as well as of beginning it as early as possible. We worked with two groups of babies with Down's syndrome, beginning the early motor training in each…

Proposal for characterization of muon spectrometers for neutrino beam lines with the Baby MIND

CERN Document Server

Noah, E

2015-01-01

Neutrino detectors based on state-of-the-art plastic scintillators read out with solid state photo-sensors, as well as new magnetization schemes, have been developed in the framework of AIDA. Meaningful size prototypes are under construction. In the framework of the CERN neutrino platform, we propose to test a Totally Active Scintillator Detector (TASD) and a prototype of a Magnetized Iron Neutrino Detector (MIND), called Baby MIND in the H8 beam line in 2016-2018. The design of the detectors and the purpose and plans for the beam tests are presented. An opportunity to use the Baby MIND detector in a real neutrino beam at JPARC for the measurement of the cross-section ratio between Water and scintillator (WAGASCI experiment) is described.

Application of numerical analysis techniques to eddy current testing for steam generator tubes

International Nuclear Information System (INIS)

Morimoto, Kazuo; Satake, Koji; Araki, Yasui; Morimura, Koichi; Tanaka, Michio; Shimizu, Naoya; Iwahashi, Yoichi

1994-01-01

This paper describes the application of numerical analysis to eddy current testing (ECT) for steam generator tubes. A symmetrical and three-dimensional sinusoidal steady state eddy current analysis code was developed. This code is formulated by future element method-boundary element method coupling techniques, in order not to regenerate the mesh data in the tube domain at every movement of the probe. The calculations were carried out under various conditions including those for various probe types, defect orientations and so on. Compared with the experimental data, it was shown that it is feasible to apply this code to actual use. Furthermore, we have developed a total eddy current analysis system which consists of an ECT calculation code, an automatic mesh generator for analysis, a database and display software for calculated results. ((orig.))

Neutron radiography by using JSW baby cyclotron

International Nuclear Information System (INIS)

Toda, Yojiro

1995-01-01

At present, JSW baby cyclotrons are mostly used for the production of the radioisotopes for medical use. The attempt to use this baby cyclotron for neutron radiography began already in 1981. The feasibility of the neutron radiography for the explosives in metallic cases which are used for H1 rockets was investigated. In 1983, it was shown that the neutron radiography by using the baby cyclotron in Muroran Works, Japan Steel Works, Ltd. was able to be carried out as a routine work. Since then, the nondestructive inspection by neutron radiography has been performed for rocket pyrotechnic articles, and contributed to heighten their reliability. Further, the radiography by using fast neutrons was developed and put to practical use for recent large H2 rockets. The JSW baby cyclotron BC 168 which has been used for neutron radiography can accelerate 16 MeV protons or 8 MeV deuterons up to 50 μA. The principle of thermal neutron radiography is the generation of fast neutrons by irradiating a Be target with the proton beam accelerated by a baby cyclotron, the moderation of the fast neutrons, the formation of the thermal neutron flux of uniform distribution with a collimator, the thermal neutron flux hitting the Gd plate in a film cassette through an object, and the exposure of an X-ray film to electrons from the Gd plate. Fast neutron radiography apparatus, and commercial neutron radiography are described. (K.I.)

Recruiting pregnant smokers from Text4baby for a randomized controlled trial of Quit4baby.

Science.gov (United States)

Leavitt, Leah; Abroms, Lorien; Johnson, Pamela; Schindler-Ruwisch, Jennifer; Bushar, Jessica; Singh, Indira; Cleary, Sean D; McInvale, Whitney; Turner, Monique

2017-06-01

Recruiting pregnant smokers into clinical trials is challenging since this population tends to be disadvantaged, the behavior is stigmatized, and the intervention window is limited. The purpose of this study is to test the feasibility and effectiveness of recruiting pregnant smokers into a smoking cessation trial by sending recruitment text messages to an existing subscriber list. Recruitment messages were sent to subscribers flagged as pregnant in Text4baby, a national text messaging program for pregnant women and mothers. Four recruitment messages were rotated to test the effectiveness of different emotional frames and a financial incentive. Study staff called subscribers who expressed interest to screen for eligibility and enroll eligible women. Between October 6, 2015 and February 2, 2016, 10,194 recruitment messages were sent to Text4baby subscribers flagged as pregnant, and 10.18% (1038) responded indicating interest. No significant increase in cancellation was observed compared to subscribers who received other ad hoc messages. Of respondents, 54.05% (561) were reached by phone for follow-up, and 21.97% (228) were found to be eligible. Among the eligible, 87% (199) pregnant smokers enrolled. The recruitment message with a pride emotional appeal had a significantly higher response (p = 0.02) compared to the recruitment message with no emotional appeal, but enrollment did not significantly differ between recruitment messages with different emotional appeals. The recruitment messages with a reference to financial incentive yielded higher response (p < 0.01) and enrollment (p = 0.03) compared to a recruitment message without. This study demonstrates success recruiting pregnant smokers using text message. Future studies should consider building on this approach for recruiting high-risk populations.

Acute heroin intoxication in a baby chronically exposed to cocaine and heroin: a case report

Directory of Open Access Journals (Sweden)

Pichini Simona

2011-07-01

Full Text Available Abstract Introduction Acute intoxication with drugs of abuse in children is often only the tip of the iceberg, actually hiding chronic exposure. Analysis using non-conventional matrices such as hair can provide long-term information about exposure to recreational drugs. Case presentation We report the case of a one-month-old Caucasian boy admitted to our pediatric emergency unit with respiratory distress and neurological abnormalities. A routine urine test was positive for opiates, suggesting an acute opiate ingestion. No other drugs of misuse, such as cocaine, cannabis, amphetamines or derivatives, were detected in the baby's urine. Subsequently, hair samples from the baby and the parents were collected to evaluate the possibility of chronic exposure to drug misuse by segmental analysis. Opiates and cocaine metabolites were detected in hair samples from the baby boy and his parents. Conclusions In light of these and previous results, we recommend hair analysis in babies and children from risky environments to detect exposure to heroin and other drug misuse, which could provide the basis for specific social and health interventions.

Testing of Photomultiplier Tubes in a Magnetic Field

Science.gov (United States)

Waldron, Zachary; A1 Collaboration

2016-09-01

The A1 collaboration at MAMI in Mainz, Germany has designed a neutron detector that can be used in experiments to measure the electric form factor of the neutron. They will measure elastic scattering from the neutron, using the polarized electron beam from MAMI at A1's experimental hall. The detector will be composed of two walls of staggered scintillator bars which will be read out by photomultiplier tubes (PMT), connected to both ends of each scintillator via light guides. The experiment requires a magnetic field with strength of 1 Tesla, 2m away from the first scintillator wall. The resulting fringe field is sufficient to disrupt the PMTs, despite the addition of Mu Metal shielding. The effects of the fringe field on these PMTs was tested to optimize the amplification of the PMTs. A Helmholtz Coil was designed to generate a controlled magnetic field with equivalent strength to the field that the PMTs will encounter. The PMTs were read out using a multi-channel analyzer, were tested at various angles relative to the magnetic field in order to determine the optimal orientation to minimize signal disruption. Tests were also performed to determine: the neutron detector response to cosmic radiation; and the best method for measuring a magnetic field's strength in two dimensions. National Science Foundation Grant No. IIA-1358175.

Job strain and coping among ageing baby boomers.

Science.gov (United States)

Wanka, Anna; Kolland, Franz; Psihoda, Sophie

2015-08-01

Research indicates that the so-called baby boomer generation (the population born after World War II) exhibits worrying health trends. Taking age-cohort effects into account, it is still unclear how the mechanisms concerning stress and health function and how the distribution of stressors, stress mediators and stress effects on health differ between generations. The article approaches stress from a generational perspective asking: which are the stressors the baby boomer generation is facing? Under which conditions and with which resources is exposure to stressors harmful to health? Is there an accumulation of stress in later working life? In the course of the project "Wellbeing", a quantitative online survey was carried out in selected commercial enterprises and public institutions in four project partner countries. The results for Austrian participants are presented in this article. Employees of the baby boomer generation are exposed to both time-related and social stressors at the workplace and a high percentage of respondents expressed symptoms of physical and psychological stress. Stress mediators, such as agency-based coping strategies and social resources at the workplace could buffer these stressors; however, stressors and stress mediators are significantly correlated creating a "triple whammy" effect (i.e. exposure to stressors, lack of social resources and restricted coping), which particularly affects older male baby boomers. Social support buffers the negative effects of a limited health and lower education for female baby boomers, which supports the buffering hypothesis of social convoy theory, whereas male baby boomers lack the resources to effectively cope with work stress.

Evaluation of the Effect of Tube Pitch and Surface Alterations on Temperature Field at Sprinkled Tube Bundle

Directory of Open Access Journals (Sweden)

Kracík Petr

2015-01-01

Full Text Available Water flowing on a sprinkled tube bundle forms three basic modes: It is the Droplet mode (liquid drips from one tube to another, the Jet mode (with an increasing flow rate droplets merge into a column and the Membrane (Sheet mode (with further increasing of falling film liquid flow rate columns merge and create sheets between the tubes. With sufficient flow rate sheets merge at this state and the tube bundle is completely covered by a thin liquid film. There are several factors influencing the individual mode types as well as heat transfer. Beside the above mentioned falling film liquid flow rate they are for instance tube diameters, tube pitches in a tube bundle or a physical condition of a falling film liquid. This paper presents a summary of data measured at atmospheric pressure at a tube bundle consisting of copper tubes of 12 milimeters diameter and of the studied tube length one meter. The tubes are positioned horizontally one above another with the tested pitches of 15, 20, 25 and 30 mm and there is a distribution tube placed above them with water flowing out. The thermal gradient of 15–40 has been tested with all pitches where the falling film liquid’s temperature at the inlet of the distribution tube was 15 °C. The liquid was heated during the flow through the exchanger and the temperature of the sprinkled (heater liquid at the inlet of the exchanger with a constant flow rate about 7.2 litres per minute was 40 °C. The tested flow of the falling film liquid ranged from 1.0 to 13.0 litres per minute. Sequences of 180 exposures have been recorded in partial flow rate stages by thermographic camera with record frequency of 30 Hz which were consequently assessed using the Matlab programme. This paper presents results achieved at the above mentioned pitches and at three types of tube bundle surfaces.

Cerebral Palsy Checklist: Babies & Preschoolers (Birth to age 5)

Science.gov (United States)

... Staying Safe Videos for Educators Search English Español Cerebral Palsy Checklist: Babies & Preschoolers KidsHealth / For Parents / Cerebral Palsy Checklist: Babies & Preschoolers What's in this article? Step ...

Twin-tubes: 3D tracking based on the ATLAS muon drift tubes

International Nuclear Information System (INIS)

Woudstra, M.; Bobbink, G.J.; Eldik, N. van; Graaf, H. van der; Kluit, P.; Koutsman, A.; Limper, M.; Linde, F.; Massaro, G.; Snuverink, J.; Vreeswijk, M.; Groenstege, H.; Koopstra, J.; Mos, S.; Rewiersma, P.; Timmermans, C.; Dijkema, J.

2006-01-01

The Monitored Drift Tubes (MDTs) of the ATLAS Muon Spectrometer have been paired to form so-called twin-tubes to measure the coordinate which runs along the wire direction. This modification endows the MDTs with full 3D track reconstruction using specially designed electronic boards. The performance of the twin-tubes has been measured for an equipped MDT chamber at the ATLAS Muon Cosmic Ray Test Stand at NIKHEF. The efficiency of a twin-tube has been determined to be 99.8%, and the measured resolution 17 cm per hit. By equipping one multilayer consisting of three layers and combining the measurements a resolution of 10 cm has been obtained

Contrastive Analysis and Research on Negative Pressure Beam Tube System and Positive Pressure Beam Tube System for Mine Use

Science.gov (United States)

Wang, Xinyi; Shen, Jialong; Liu, Xinbo

2018-01-01

Against the technical defects of universally applicable beam tube monitoring system at present, such as air suction in the beam tube, line clogging, long sampling time, etc., the paper analyzes the current situation of the spontaneous combustion fire disaster forecast of mine in our country and these defects one by one. On this basis, the paper proposes a research thought that improving the positive pressure beam tube so as to substitute the negative pressure beam tube. Then, the paper introduces the beam tube monitoring system based on positive pressure technology through theoretical analysis and experiment. In the comparison with negative pressure beam tube, the paper concludes the advantage of the new system and draws the conclusion that the positive pressure beam tube is superior to the negative pressure beam tube system both in test result and test time. At last, the paper proposes prospect of the beam tube monitoring system based on positive pressure technology.

Microdischarges in DC accelerator tubes

International Nuclear Information System (INIS)

Eastham, D.A.; Thorn, R.

1978-07-01

Voltage tests on the Daresbury ceramic/titanium accelerator tube have shown that microdischarges play an important role in the conditioning process. It has been found that the voltage onset for microdischarges in a tube is dependent on the surface contamination of the electrodes and the tube geometry (in particular the tube length). This geometrical effect can be related to the trajectories of secondary ions emitted from the electrode surfaces. Sensitive diagnostic techniques have been developed to study the mass and energy distribution of ions emitted along the axis of the tube during these predischarges. The energy distribution of protons (and H - ions) can be related to the origins of the discharges in the tube. Detailed results are presented for a particular tube geometry. (author)

Contribution to the heat transfer analysis of substitute refrigerants in evaporator tubes with smooth or enhanced tube surfaces

Energy Technology Data Exchange (ETDEWEB)

Kattan, N

1997-12-31

The substitution of CFC refrigerants in refrigeration systems, heat pumps and organic Rankine cycles for heat recovery, requests a good knowledge of heat transfer properties of substitute fluids. A new test facility has been built at the Laboratory for Industrial Energy Systems (LENI) to contribute to this international effort. It consists of two sets of concentric tubes allowing either annular or inside tube convective boiling with a counter current water flow heating to be studied. A new data base including heat transfer coefficients and pressure drop measurements for four new refrigerants (R123, R134A, R402A and R404A) and three older refrigerants (R11, R12 and R502) has been collected. Flow boiling measurements covered a broad range of mass velocities, vapor qualities and heat fluxes. Some of the tests included plain tubes and others enhanced surface tubes (microfilms from Wieland) in horizontal and vertical orientations. An improved Wilson plot technique, that covers both the transition and turbulent flow regimes of the water flowing in the annular channel for the inside tube boiling tests, is proposed to overcome the severe limitations of conventional Wilson plots, to improve accuracy and to facilitate data processing. Mean flow boiling heat transfer coefficients were measured for R12 and R134A evaporating inside a horizontal plain tube and for R11 and R123 evaporating inside a horizontal plain tube. Local flow boiling heat transfer coefficients were measured for : R134A, R123, R404A and R502 evaporating inside a horizontal plain tube, for R134A and R123 evaporating inside a horizontal microfin tube and for R134 evaporating inside a vertical microfin tube. In addition microfin heat transfer augmentation relative to plain tube test data was investigated. The measured heat transfer coefficients were compared to different existing inside tube flow boiling correlations. (author) figs., tabs., refs.

The Impact of Baby Swimming on Introductory and Elementary Swimming Training

OpenAIRE

Břízová, Gabriela

2007-01-01

THESIS ANNOTATION Title: The Impact of Baby Swimming on Introductory and Elementary Swimming Training Aim: To assess the impact of 'baby swimming' on the successfulness in introductory and partly in elementary swimming training, and to find out whether also other circumstances (for example the length of attendance at 'baby swimming') have some influence on introductory swimming training. Methods: We used a questionnaire method for the parents of children who had attended 'baby swimming' and f...

Pilot evaluation of the text4baby mobile health program

Directory of Open Access Journals (Sweden)

Evans William Douglas

2012-11-01

Full Text Available Abstract Background Mobile phone technologies for health promotion and disease prevention have evolved rapidly, but few studies have tested the efficacy of mobile health in full-fledged programs. Text4baby is an example of mobile health based on behavioral theory, and it delivers text messages to traditionally underserved pregnant women and new mothers to change their health, health care beliefs, practices, and behaviors in order to improve clinical outcomes. The purpose of this pilot evaluation study is to assess the efficacy of this text messaging campaign. Methods We conducted a randomized pilot evaluation study. All participants were pregnant women first presenting for care at the Fairfax County, Virginia Health Department. We randomized participants to enroll in text4baby and receive usual health care (intervention, or continue simply to receive usual care (control. We then conducted a 24-item survey by telephone of attitudes and behaviors related to text4baby. We surveyed participants at baseline, before text4baby was delivered to the intervention group, and at follow-up at approximately 28 weeks of baby’s gestational age. Results We completed 123 baseline interviews in English and in Spanish. Overall, the sample was predominantly of Hispanic origin (79.7% with an average age of 27.6 years. We completed 90 follow-up interviews, and achieved a 73% retention rate. We used a logistic generalized estimating equation model to evaluate intervention effects on measured outcomes. We found a significant effect of text4baby intervention exposure on increased agreement with the attitude statement “I am prepared to be a new mother” (OR = 2.73, CI = 1.04, 7.18, p = 0.042 between baseline and follow-up. For those who had attained a high school education or greater, we observed a significantly higher overall agreement to attitudes against alcohol consumption during pregnancy (OR = 2.80, CI = 1.13, 6.90, p = 0.026. We also observed a

Babies Need Tummy Time

Science.gov (United States)

... sharing on social media links Babies Need Tummy Time! Page Content Tummy Time is not only an ... of your baby’s normal growth. What Is Tummy Time? Tummy Time describes the times when you place ...

Some problems in the technique of high-voltage testing of the accelerating tube gaps in electrostatic accelerators

International Nuclear Information System (INIS)

Romanov, V.A.; Ivanov, V.V.; Mukhametshin, V.I.; Dmitriev, E.P.; Kidalov, A.I.

1983-01-01

Problems arising during high-voltage testing and training of accelerating taubes of electrostatic accelrators are discussed. A rig and technique of the accelerating tube testing and program designed for the processing of the data obtained and sorting out of the samples investigated are described

Formability of Micro-Tubes in Hydroforming

International Nuclear Information System (INIS)

Hartl, Christoph; Anyasodor, Gerald; Lungershausen, Joern

2011-01-01

Micro-hydroforming is a down-scaled metal forming process, based on the expansion of micro-tubes by internal pressurization within a die cavity. The objective of micro-hydroforming is to provide a technology for the economic mass production of complex shaped hollow micro-components. Influence of size effects in metal forming processes increases with scaling down of metal parts. Investigations into the change in formability of micro-tubes due to metal part scaling down constituted an important subject within the conducted fundamental research work. Experimental results are presented, concerning the analysis of the formability of micro-tubes made from stainless steel AISI 304 with an outer diameter of 800 μm and a wall thickness of 40 μm. An average ratio of tube wall thickness to grain size of 1.54 of up to 2.56 was analyzed. Miniaturised mechanical standard methods as well as bulge tests with internal hydrostatic pressurization of the tubular specimens were applied to analyze the influence of size-dependent effects. A test device was developed for the bulge experiments which enabled the pressurization of micro-tubes with internal pressures up to 4000 bar. To determine the attainable maximum achievable expansion ratio the tubes were pressurized in the bulge tests with increasing internal pressure until instability due to necking and subsequent bursting occurred. Comparisons with corresponding tests of macro-tubes, made from the here investigated material, showed a change in formability of micro-tubes which was attributed to the scaling down of the hydroforming process. In addition, a restricted applicability of existing theoretical correlations for the determination of the maximum pressure at bursting was observed for down-scaled micro-hydroforming.

Blood and urine 8-iso-PGF2α levels in babies of different gestational ages.

Science.gov (United States)

Li, Sitao; Hao, Hu; Zhou, Ping; Gao, Ping Ming; Xiao, Xin

2014-01-01

We measured cord blood and urine 8-iso-prostaglandin F2α (8-iso-PGF2α) levels in babies of different gestational ages to determine lipid peroxidation status. Babies at gestational ages of 28-43 weeks were divided into group A (28-32 weeks), group B (33-36 weeks), group C (37-41 weeks), and group D (42-43 weeks). 8-iso-PGF2α in umbilical cord blood (UCB) at birth and urine at 6 hours after birth was and tested by ELISA. UCB and urine 8-iso-PGF2α levels in group C were 130.09 ± 31.73 pg/ml and 27.14 ± 6.73 pg/ml, respectively. UCB 8-iso-PGF2α levels in group A and B were 188.42 ± 59.34 pg/ml and 189.37 ± 68.46 pg/ml, and urine 8-iso-PGF2α were 32.14 ± 7.32 pg/ml and 30.46 ± 8.83 pg/ml, respectively. Blood and urine 8-iso-PGF2α levels in group D (post-term) were 252.01 ± 46.42 pg/ml and 44.00 ± 8.50 pg/ml. For all babies, UCB and urine iso-PGF2α levels were significantly correlated (r = 0.65, P iso-PGF2α levels in normal full-term babies. Urine 8-iso-PGF2α levels may reflect the extent of lipid peroxidation in babies. In pre-term and post-term babies, there was evidence for increased lipid peroxidation.

Blood compatibility assessment of graft copolymer (NR-g-DMAA) tubes

International Nuclear Information System (INIS)

Razzak, M.T.; Otsuhata, Kazushige; Tabata, Yoneho; Ohashi, Fumio; Takeuchi, Atsuki

1992-01-01

Graft copolymer (NR-g-DMAA) tubes have been prepared using simultaneous radiation induced grafting of N,N-dimethyl-acrylamide, (DMAA) onto natural rubber (NR) tubes. The blood compatibility of the NR-g-DMAA tubes was assessed with three methods, namely in vitro test, ex vivo once through test and ex vivo loops test. In the case of the in vitro test, a simple whole blood contacting procedure has been employed. The ex vivo once through test involves the exposing of NR-g-DMAA tubes with once through flow of fresh canine blood and then it was inspected for any evidence of clot. In the case of ex vivo loops test, the NR-g-DMAA tube was implanted at external jugular vein of a mongrel canine and the blood flow in the NR-g-DMAA tube was detected with an ultrasonic flow meter. It was found that the blood compatibility of NR-g-DMAA tubes is improved significantly with the increasing degree of grafting. All the NR-g-DMAA tubes having a degree of grafting of about 30 wt% or more exhibit good blood compatibility. It was found that the blood compatibility of the NR-g-DMAA tube is better than that of a medical grade silicon rubber (SiR) tube. (Author)

Test beam analysis of the first CMS drift tube muon chamber

CERN Document Server

Albajar, C; Arce, P; Autermann, C; Bellato, M; Benettoni, M; Benvenuti, Alberto C; Bontenackels, M; Caballero, J; Cavallo, F R; Cerrada, M; Cirio, R; Colino, N; Conti, E; de la Cruz, B; Dal Corso, F; Dallavalle, G M; Fernández, C; Fernández de Troconiz, J; Fouz-Iglesias, M C; García-Abia, P; García-Raboso, A; Gasparini, F; Gasparini, U; Giacomelli, P; Gonella, F; Gulmini, M; Hebbeker, T; Hermann, S; Höpfner, K; Jiménez, I; Josa-Mutuberria, I; Lacaprara, S; Marcellini, S; Mariotti, C; Maron, G; Maselli, S; Meneguzzo, Anna Teresa; Monaco, V; Montanari, A; Montanari, C; Montecassiano, F; Navarria, Francesco Luigi; Odorici, F; Passaseo, M; Pegoraro, M; Peroni, C; Perrotta, A; Puerta, J; Reithler, H; Romero, A; Romero, L; Ronchese, P; Rossi, A; Rovelli, T; Sacchi, R; Sowa, M; Staiano, A; Toniolo, N; Torassa, E; Vaniev, V; Vanini, S; Ventura, Sandro; Villanueva, C; Willmott, C; Zotto, P L; Zumerle, G

2004-01-01

In October 2001 the first produced CMS Barrel Drift Tube (DT) Muon Chamber was tested at the CERN Gamma Irradiation Facility (GIF) using a muon beam. A Resistive Plate Chamber (RPC) was attached to the top of the DT chamber, and, for the first time, both detectors were operated coupled together. The performance of the DT chamber was studied for several operating conditions, and for gamma rates similar to the ones expected at LHC. In this paper we present the data analysis; the results are considered fully satisfactory.

Test beam analysis of the first CMS drift tube muon chamber

International Nuclear Information System (INIS)

Albajar, C.; Amapane, N.; Arce, P.; Autermann, C.; Bellato, M.; Benettoni, M.; Benvenuti, A.; Bontenackels, M.; Caballero, J.; Cavallo, F.R.; Cerrada, M.; Cirio, R.; Colino, N.; Conti, E.; Cruz, B. de la; Corso, F. dal; Dallavalle, G.M.; Fernandez, C.; Troconiz, J.F. de; Fouz, M.C.; Garcia-Abia, P.; Garcia-Raboso, A.; Gasparini, F.; Gasparini, U.; Giacomelli, P.; Gonella, F.; Gulmini, M.; Hebbeker, T.; Hermann, S.; Hoepfner, K.; Jimenez, I.; Josa, I.; Lacaprara, S.; Marcellini, S.; Mariotti, C.; Maron, G.; Maselli, S.; Meneguzzo, A.T.; Monaco, V.; Montanari, A.; Montanari, C.; Montecassiano, F.; Navarria, F.L.; Odorici, F.; Passaseo, M.; Pegoraro, M.; Peroni, C.; Perrotta, A.; Puerta, J.; Reithler, H.; Romero, A.; Romero, L.; Ronchese, P.; Rossi, A.; Rovelli, T.; Sacchi, R.; Sowa, M.; Staiano, A.; Toniolo, N.; Torassa, E.; Vaniev, V.; Vanini, S.; Ventura, S.; Villanueva, C.; Willmott, C.; Zotto, P.; Zumerle, G.

2004-01-01

In October 2001 the first produced CMS Barrel Drift Tube (DT) Muon Chamber was tested at the CERN Gamma Irradiation Facility (GIF) using a muon beam. A Resistive Plate Chamber (RPC) was attached to the top of the DT chamber, and, for the first time, both detectors were operated coupled together. The performance of the DT chamber was studied for several operating conditions, and for gamma rates similar to the ones expected at LHC. In this paper we present the data analysis; the results are considered fully satisfactory

Test beam analysis of the first CMS drift tube muon chamber

Energy Technology Data Exchange (ETDEWEB)

Albajar, C.; Amapane, N.; Arce, P.; Autermann, C.; Bellato, M.; Benettoni, M.; Benvenuti, A.; Bontenackels, M.; Caballero, J.; Cavallo, F.R.; Cerrada, M.; Cirio, R.; Colino, N.; Conti, E.; Cruz, B. de la; Corso, F. dal; Dallavalle, G.M.; Fernandez, C.; Troconiz, J.F. de E-mail: jorge.troconiz@uam.es; Fouz, M.C.; Garcia-Abia, P.; Garcia-Raboso, A.; Gasparini, F.; Gasparini, U.; Giacomelli, P.; Gonella, F.; Gulmini, M.; Hebbeker, T.; Hermann, S.; Hoepfner, K.; Jimenez, I.; Josa, I.; Lacaprara, S.; Marcellini, S.; Mariotti, C.; Maron, G.; Maselli, S.; Meneguzzo, A.T.; Monaco, V.; Montanari, A.; Montanari, C.; Montecassiano, F.; Navarria, F.L.; Odorici, F.; Passaseo, M.; Pegoraro, M.; Peroni, C.; Perrotta, A.; Puerta, J.; Reithler, H.; Romero, A.; Romero, L.; Ronchese, P.; Rossi, A.; Rovelli, T.; Sacchi, R.; Sowa, M.; Staiano, A.; Toniolo, N.; Torassa, E.; Vaniev, V.; Vanini, S.; Ventura, S.; Villanueva, C.; Willmott, C.; Zotto, P.; Zumerle, G

2004-06-11

In October 2001 the first produced CMS Barrel Drift Tube (DT) Muon Chamber was tested at the CERN Gamma Irradiation Facility (GIF) using a muon beam. A Resistive Plate Chamber (RPC) was attached to the top of the DT chamber, and, for the first time, both detectors were operated coupled together. The performance of the DT chamber was studied for several operating conditions, and for gamma rates similar to the ones expected at LHC. In this paper we present the data analysis; the results are considered fully satisfactory.

First joint test beam of CMS Drift Tubes (DT) and Resistive Plate Chambers (RPC)

CERN Multimedia

Paolo Giacomelli

2001-01-01

The first full size muon drift tube chamber ever built for the CMS barrel with the final cell design (constructed at CIEMAT, Madrid) was succesfully tested with a muon beam in September 2001 at the Gamma Irradiation Facility (GIF) at CERN. For the first time also both muon detectors for the CMS barrel (DT + RPC) were coupled together. The results of this test were fully succesful and confirmed the excellent performance of both detectors together in a radiation environment.

GERDA test facility for pressurized water reactors with straight tube steam generators

International Nuclear Information System (INIS)

Ahrens, G.; Haury, G.; Lahner, K.; Schatz, A.

1983-01-01

A number of large-scale experimental facilities have been constructed and operate in order to experiment on the thermodynamic and thermohydraulic behaviour of nuclear facilities in case of LOCA. Most of them were designed for ''large leak'' accidents, but as ''small leak'' accidents became the focus of interest, such experiments were also carried out. Experiments carried out with this arrangement for PWR-type reactors with straight-tube steam generators are only partially evaluable. BBR and B and W therefore cooperated in the construction of the test facility GERDA, designed for testing reactors of BBR design. It supplied relevant experimental results for the nuclear power plant at Muelheim-Kaerlich. (orig.) [de

N=1 supersymmetric extension of the baby Skyrme model

International Nuclear Information System (INIS)

Adam, C.; Queiruga, J. M.; Sanchez-Guillen, J.; Wereszczynski, A.

2011-01-01

We construct a method to supersymmetrize higher kinetic terms and apply it to the baby Skyrme model. We find that there exist N=1 supersymmetric extensions for baby Skyrme models with arbitrary potential.

Use of CATHENA to model calandria-tube/moderator heat transfer after pressure-tube/calandria-tube ballooning contact

International Nuclear Information System (INIS)

Fan, H.Z.; Bilanovic, Z.; Nitheanandan, T.

2004-01-01

A study was performed to assess the effect of the calandria-tube/moderator heat transfer after pressure-tube/calandria tube ballooning contact using CATHENA. Results of this study indicated that the analytical tool, CATHENA, can be applied for pool boiling heat transfer on the external surface of a large diameter tube, such as the calandria tube used in CANDU reactors. The methodology in such CANDU-generic study can be used to simulate the tube surface with multiple boiling regimes and to assess the benefits of closely coupling thermalhydraulics modelling and fuel/fuel channel behaviour modelling. CATHENA (Canadian Algorithm for THErmalhydraulic Network Analysis) is a one-dimensional, two-fluid thermalhydraulic simulation code designed by AECL to analyse two-phase flow and heat transfer in piping networks. The detailed heat transfer package in CATHENA allows a connection to be established from the multiple solid surfaces of tubes to the surrounding large amount of moderator water, which acts as a heat sink during a postulated loss of coolant event. The generalized heat transfer package within CATHENA allows the tube walls to be divided into several layers in the radial direction and several sectors in the circumferential direction, to account for heat transfer conditions in these two directions. The CATHENA code with the generalized heat transfer package is capable of capturing key pool-boiling phenomena such as nucleate, transition and film boiling heat transfer as well as an ability to model the rewet phenomenon to some extent. A CATHENA input model was generated and used in simulations of selected contact boiling experiment test cases. The transient wall temperatures have been calculated in different portions of the calandria tube. By using this model an adequate agreement was achieved between CATHENA calculation and experimental measurement The CATHENA code enables one to investigate the transient and local thermal-mechanical behaviour of the calandria tube

Pedagogy with Babies: Perspectives of Eight Nursery Managers

Science.gov (United States)

Elfer, Peter; Page, Jools

2015-01-01

The last 30 years have seen a significant increase in babies attending nursery, with corresponding questions about the aims and organisation of practice. Research broadly agrees on the importance of emotionally consistent, sensitive and responsive interactions between staff and babies. Policy objectives for nursery and expectations of parents and…

Influence of the centrifuge time of primary plasma tubes on routine coagulation testing.

Science.gov (United States)

Lippi, Giuseppe; Salvagno, Gian Luca; Montagnana, Martina; Manzato, Franco; Guidi, Gian Cesare

2007-07-01

Preparation of blood specimens is a major bottleneck in the laboratory throughput. Reliable strategies for reducing the time required for specimen processing without affecting quality should be acknowledged, especially for laboratories performing stat analyses. The present investigation was planned to establish a minimal suitable centrifuge time for primary samples collected for routine coagulation testing. Five sequential primary vacuum tubes containing 0.109 mol/l buffered trisodium citrate were collected from 10 volunteers and were immediately centrifuged on a conventional centrifuge at 1500 x g, at room temperature for 1, 2, 5, 10 and 15 min, respectively. Hematological and routine coagulation testing, including prothrombin time, activated partial thromboplastin time and fibrinogen, were performed. The centrifugation time was inversely associated with residual blood cell elements in plasma, especially platelets. Statistically significant variations from the reference 15-min centrifuge specimens were observed for fibrinogen in samples centrifuged for 5 min at most and for the activated partial thromboplastin time in samples centrifuged for 2 min at most. Meaningful biases related to the desirable bias were observed for fibrinogen in samples centrifuged for 2 min at most, and for the activated partial thromboplastin time in samples centrifuged for 1 min at most. According to our experimental conditions, a 5-10 min centrifuge time at 1500 x g may be suitable for primary tubes collected for routine coagulation testing.

Analysis of muscle tone distribution in premature babies based on PodoBaby podoscope examination

Directory of Open Access Journals (Sweden)

Stępowska Jolanta

2017-12-01

Full Text Available Introduction: The aim of the study was to assess load surface with regard to muscle tone distribution of premature infants compared to full-term infants. Material and methods: Twenty-four infants aged 3-6 months (adjusted age were examined, including 12 premature infants (born before 37 weeks and 12 full-term infants. The study was carried out at the Children’s Memorial Health Institute in Warsaw in the period from January to June 2016. The study involved interviews with the infants’ parents and examinations of infants in a supine and prone position performed on PodoBaby digital podoscope. Support surface, i.e. the loading on the left and right side of the body and the length of trunk sides were analysed. Statistical analysis was performed with the use of Statistica v.12 software and Student’s t-test. Results: No significant differences between premature infants and full-term infants regarding the loading on the right side measured in a supine position were revealed (analogous lack of differences was noted on the left side and in a prone position. In a prone position, the correlation between support surface and the length of trunk sides was noted, i.e. the loaded side of the trunk was lengthened, while the unloaded side was shortened. Conclusions: Considerable asymmetry of the loads of trunk sides was noted in premature infants, while in the case of full-term infants, the values of loads were close to symmetry. An examination with the use of PodoBaby podoscope may be applied in early diagnostics in pediatric rehabilitation.

Development of a sealing process of capsules for surveillance test tubes of the vessel in nuclear power plants; Desarrollo de proceso de sellado de capsulas para probetas de vigilancia de la vasija en nucleoelectricas

Energy Technology Data Exchange (ETDEWEB)

Romero C, J.; Fernandez T, F.; Perez R, N.; Rocamontes A, M.; Garcia R, R. [ININ, Km 36.5 Carretera Mexico-Toluca, 52750 La Marquesa, Estado de Mexico (Mexico)

2007-07-01

The surveillance capsule is composed by the support, three capsules for impact test tubes, five capsules for tension test tubes and one porta dosemeters. The capsules for test tubes are of two types: rectangular capsule for Charpy test tubes and cylindrical capsule for tension test tubes. This work describes the development of the welding system to seal the capsules for test tubes that should contain helium of ultra high purity to a pressure of 1 atmosphere. (Author)

Gastrostomy Tube (G-Tube)

Science.gov (United States)

... any of these problems: a dislodged tube a blocked or clogged tube any signs of infection (including redness, swelling, or warmth at the tube site; discharge that's yellow, green, or foul-smelling; fever) excessive bleeding or drainage from the tube site severe abdominal pain lasting ...

Tube bundle vibrations in transversal flow

International Nuclear Information System (INIS)

Gibert, R.J.; Sagner, M.

1978-01-01

This study gives important information concerning characteristic parameters about lock-in and whirling instability phenomena, in the case of tube arrays. The work is mainly an experimental one though models are also developed: 1) an equilateral pitch bundle (p=1,5 D with D=tube diameter) is tested. Tube damping (epsilon) and first eigenfrequency (f), flow velocity are explored in a large domain. Vibratory level of the tubes are measured and critical points are ploted on the fluidelastic parameters diagram. Several bundles with various usual pitches and arrangements (in line or staggered) are tested. Critical velocities are measured and the whirling instability characteristic coefficient is tabulated. A complementary experiment is made on tube rows with various pitches. This gives valuable informations concerning the look-in domain in VR and A'R diagram. Furthermore this puts in evidence the important effect of a frequency difference between two adjacent tubes on the whirling critical velocity

Gauged BPS baby Skyrmions with quantized magnetic flux

Science.gov (United States)

Adam, C.; Wereszczynski, A.

2017-06-01

A new type of gauged BPS baby Skyrme model is presented, where the derivative term is just the Schroers current (i.e., gauge invariant and conserved version of the topological current) squared. This class of models has a topological bound saturated for solutions of the pertinent Bogomolnyi equations supplemented by a so-called superpotential equation. In contrast to the gauged BPS baby Skyrme models considered previously, the superpotential equation is linear and, hence, completely solvable. Furthermore, the magnetic flux is quantized in units of 2 π , which allows, in principle, to define this theory on a compact manifold without boundary, unlike all gauged baby Skyrme models considered so far.

Procedure and device for extracting the end of a tube inserted into a hole in a tube plate

International Nuclear Information System (INIS)

1980-01-01

When constructing heat exchangers and steam generators, particularly in the construction of steam generators for nuclear power stations, many small diameter tubes have to be secured into a very thick tube plate for instance 600 mm thick. This crimping or expanding of the tube is generally performed by rolling the internal surface of the tube inside a hole drilled right through the tube plate and slightly greater in diameter than the external diameter of the tube before the tube is rolled. To check the tubes for defects, it is necessary to extract certain tubes from the tube plate in order to move the tube to a testing and inspection point and examine the part of it that was secured in the plate hole. The invention concerns the uncrimping of these tubes [fr

How Babies Think

Science.gov (United States)

Bachleda, Amelia R.; Thompson, Ross A.

2018-01-01

Babies think differently than adults, and understanding how they think can help us see their explosive brain growth in everyday behavior. Infants learn language faster than adults do, use statistics to understand how the world works, and even reason about the minds of others. But these achievements can be hidden by their poor self-regulatory…

The effect of tube-support interaction on the dynamic response of heat exchanger tubes

International Nuclear Information System (INIS)

Shin, Y.S.; Jendrzejczyk, J.A.; Wambsganss, M.W.

1977-01-01

To avoid detrimental tube vibration in heat exchangers, resonant conditions and instabilitites must be avoided, and/or peak dynamic amplitudes must not exceed allowable limits. In attempting a theoretical analysis, questions arise as to the effects of tube/support interaction on tube vibrational characteristics (i.e. resonant frequencies, modes, damping) and response amplitude. As a part of ANL's Flow-Induced Vibration Program in support of the Clinch River Breeder Reactor Plant (CRBRP) steam generator design activity, tube/support interaction experiments are being performed not only to gain the insight into the dynamic behavior of CRBRP steam generator tubes, but also to provide the basis for developing design guidance. Test results were compared with anaytical results based on multispan tube with 'knife-edge' supports at the support locations. (Auth.)

Automatic welding of stainless steel tubing

Science.gov (United States)

Clautice, W. E.

1978-01-01

The use of automatic welding for making girth welds in stainless steel tubing was investigated as well as the reduction in fabrication costs resulting from the elimination of radiographic inspection. Test methodology, materials, and techniques are discussed, and data sheets for individual tests are included. Process variables studied include welding amperes, revolutions per minute, and shielding gas flow. Strip chart recordings, as a definitive method of insuring weld quality, are studied. Test results, determined by both radiographic and visual inspection, are presented and indicate that once optimum welding procedures for specific sizes of tubing are established, and the welding machine operations are certified, then the automatic tube welding process produces good quality welds repeatedly, with a high degree of reliability. Revised specifications for welding tubing using the automatic process and weld visual inspection requirements at the Kennedy Space Center are enumerated.

Aggressive posterior retinopathy of prematurity in large preterm babies in South India.

Science.gov (United States)

Shah, Parag K; Narendran, Venkatapathy; Kalpana, Narendran

2012-09-01

To describe aggressive posterior retinopathy of prematurity (APROP) in a subset of premature babies, having gestational age (GA) of ≥28 weeks and birth weight (BW) of ≥1000 g. Retrospective observational case series. Case records of 99 babies, who were diagnosed to have APROP between July 2002 and October 2010 were reviewed. Fundus fluorescein angiography (FFA) was carried out in 19 babies. The mean GA was 31.7 weeks (range 28-35 weeks) and mean BW was 1572 g (range 1000-2310 g). All these babies received supplemental unblended oxygen 3 days or longer after birth. Of the 52 babies who had an eye exam in the neonatal intensive care unit prior to discharge, 35 babies had loss of vascularised retina from zone II to zone I and four babies from zone III to zone I, when examined as an outpatient. FFA revealed large geographic areas of vaso-obliteration (more than 30 disc areas) posterior to the shunt vessels within vascularised retina. Features of severe capillary bed loss in the vascularised retina were seen in our cases. Oxygen could be a precipitating factor in causing this retinopathy of prematurity in large babies.

Comparison of characteristics parameters in the evaluation of wall thickness diminishing in admiralty brass tubes of the steam condenser, tested by eddy currents

International Nuclear Information System (INIS)

Obrutsky, Alba E.; Mendez, Jorge A.; Acosta, Cesar D.; Scopelliti, Jose D.

1999-01-01

This work is aimed to appraise the measure of the wall thickness diminishing in the signals evaluation obtained in the inspection of steam condenser by eddy currents. In the analysis of the obtained signals were observed in the brass tubes a great quantity of internal defects whose signal indicates that there were diminishing of the wall thickness between 80% and 100%. With all this information and analyzing the data acquired, the tubes with more important indications were selected to make a more exhaustive study of the found defectology. As first test, it was measured the thickness of the worn tubes, comparing them with the original ones that are in stock. It was verified that the tubes separated for this study presented a 30% less thickness in comparison with the new tubes. A semiquantitative chemical test (EDAX) was made to verify if it was the same material. One of the extracted tubes (066 Y1) was reinspected in order to isolate the area with indications. Once this was performed, it was decided to cut the tube to make a visual inspection and to evaluate to what type of defect corresponds to the signals obtained. In the metallography it was confirm that it was a horseshoe type defect. When performing a dimensional control test of the found real defect, it was checked that the information obtained by eddy currents regarding the diminishing of the wall thickness diminishing was valid. At a last stage of the test, it was proceed to make an study and verification of the used parameters, probes, standards and finally determine which shall be the convenient modifications to minimize errors. (author)

Mortality and morbidity pattern in small-for gestational age and appropriate-for-gestational age very preterm babies: a hospital based study

International Nuclear Information System (INIS)

Muhammad, T.; Khattak, A.A.; Rehman, S.U.

2009-01-01

Very preterm babies are important group of paediatric babies who require special attention. These babies are known to have increased risk of morbidity and mortality. Studying the morbidity and mortality pattern for this important paediatric group can help in better understanding of their care in the hospital settings. Objective of the study was to compare the mortality and morbidity pattern in Small-for-gestational age and appropriate-for-gestational age very preterm babies. This hospital based prospective (cohort) study was conducted at the department of Paediatrics, Postgraduate Medical Institute, Lady Reading Hospital, Peshawar from March 2008 to April 2009. One hundred Small-for-gestational age (SGA) live born very preterm babies were compared with 100 appropriate-for-gestational age (AGA) very preterm babies having similar gestational ages. Information regarding gestational age, birth weight, mortality, and morbidity (in terms of various biochemical and clinical markers) were recorded on a pre-designed questionnaire. Data analysis was done using SPSS version 15. Results were interpreted in terms of descriptive (mean, proportions, standard deviation) and inferential statistical tests (with p-values). There was no difference between the two groups (SGA Vs AGA) with regards to gestational age and gender of the babies The mean weight of SGA babies was significantly lower as compared to AGA babies (1.1+-0.16 Kg Vs 1.5+-0.2 Kg; p=0.001). As compared to AGA babies, the SGA babies had a higher mortality (40% Vs 22%, p=0.006), and higher morbidity in terms of hyperbilirubinaemia (67% Vs 51%, p=0.02) and hypocalcaemia (24% Vs 10%, p=0.02). The difference in the mortality between the two groups was more prominent in babies with gestational age < 31 weeks (71.4% for SGA as compared to 39.3 % for AGA very preterm babies with gestational age < 31 weeks). Very preterm SGA infants have significantly higher mortality and morbidity in comparison to the AGA babies. In deciding

Infertility trial outcomes: healthy moms and babies.

Science.gov (United States)

Silver, Robert