Evaluation of metals, metalloids, and ash mixture toxicity using sediment toxicity testing.

Science.gov (United States)

Stojak, Amber; Bonnevie, Nancy L; Jones, Daniel S

2015-01-01

In December 2008, a release of 4.1 million m(3) of coal ash from the Tennessee Valley Authority Kingston Fossil Plant occurred. Ash washed into the Emory River and migrated downstream into the Clinch and Tennessee Rivers. A Baseline Ecological Risk Assessment evaluated risks to ecological receptors from ash in the river system post-dredging. This article describes the approach used and results from sediment toxicity tests, discussing any causal relationships between ash, metals, and toxicity. Literature is limited in the realm of aquatic coal combustion residue (CCR) exposures and the potential magnitude of effects on benthic invertebrates. Sediment samples along a spectrum of ash content were used in a tiered toxicity testing approach and included a combination of 10 day sediment toxicity acute tests and longer-term, partial life cycle "definitive" tests with 2 species (Hyalella azteca and Chironomus dilutus). Arsenic, and to a lesser extent Se, in the ash was the most likely toxicant causing observed effects in the laboratory toxicity tests. Sites in the Emory River with the greatest statistical and biologically significant effects had As concentrations in sediments twice the probable effects concentration of 33 mg/kg. These sites contained greater than 50% ash. Sites with less than approximately 50% ash in sediments exhibited fewer significant toxic responses relative to the reference sediment in the laboratory. The results discussed here present useful evidence of only limited effects occurring from a worst-case exposure pathway. These results provided a valuable line of evidence for the overall assessment of risks to benthic invertebrates and to other ecological receptors, and were crucial to risk management and development of project remediation goals. © 2014 SETAC.

Effects of sediment-spiked lufenuron on benthic macroinvertebrates in outdoor microcosms and single-species toxicity tests

Energy Technology Data Exchange (ETDEWEB)

Brock, T.C.M., E-mail: theo.brock@wur.nl [Alterra, Wageningen University and Research Centre, P.O. Box 47, 6700 AA Wageningen (Netherlands); Bas, D.A. [Institute for Biodiversity and Ecosystem Dynamics (IBED), University of Amsterdam (Netherlands); Belgers, J.D.M. [Alterra, Wageningen University and Research Centre, P.O. Box 47, 6700 AA Wageningen (Netherlands); Bibbe, L. [Institute for Biodiversity and Ecosystem Dynamics (IBED), University of Amsterdam (Netherlands); Boerwinkel, M-C.; Crum, S.J.H. [Alterra, Wageningen University and Research Centre, P.O. Box 47, 6700 AA Wageningen (Netherlands); Diepens, N.J. [Department of Aquatic Ecology and Water Quality Management, Wageningen University, P.O. Box 47, 6700 AA Wageningen (Netherlands); Kraak, M.H.S.; Vonk, J.A. [Institute for Biodiversity and Ecosystem Dynamics (IBED), University of Amsterdam (Netherlands); Roessink, I. [Alterra, Wageningen University and Research Centre, P.O. Box 47, 6700 AA Wageningen (Netherlands)

2016-08-15

Highlights: • In outdoor microcosms constructed with lufenuron-spiked sediment we observed that this insecticide persistent in the sediment compartment. • Sediment exposure to lufenuron caused population-level declines (insects and crustaceans) and increases (mainly oligochaete worms) of benthic invertebrates. • The direct and indirect effects observed in the microcosms were supported by results of sediment-spiked single species tests with Chironomus riparius, Hyalella azteca and Lumbriculus variegatus. • The tier-1 effect assessment procedure for sediment organisms recommended by the European Food Safety Authority is protective for the treatment-related responses observed in the microcosm test. - Abstract: Sediment ecotoxicity studies were conducted with lufenuron to (i) complement the results of a water-spiked mesocosm experiment with this lipophilic benzoylurea insecticide, (ii) to explore the predictive value of laboratory single-species tests for population and community-level responses of benthic macroinvertebrates, and (iii) to calibrate the tier-1 effect assessment procedure for sediment organisms. For this purpose the concentration-response relationships for macroinvertebrates between sediment-spiked microcosms and those of 28-d sediment-spiked single-species toxicity tests with Chironomus riparius, Hyalella azteca and Lumbriculus variegatus were compared. Lufenuron persisted in the sediment of the microcosms. On average, 87.7% of the initial lufenuron concentration could still be detected in the sediment after 12 weeks. Overall, benthic insects and crustaceans showed treatment-related declines and oligochaetes treatment-related increases. The lowest population-level NOEC in the microcosms was 0.79 μg lufenuron/g organic carbon in dry sediment (μg a.s./g OC) for Tanytarsini, Chironomini and Dero sp. Multivariate analysis of the responses of benthic macroinvertebrates revealed a community-level NOEC of 0.79 μg a.s./g OC. The treatment

Sediment Origin Determination in the Sub-Catchment of Mistelbach (Austria) using Fatty Acids Biomarkers and Compound-Specific Stable Isotope Techniques

International Nuclear Information System (INIS)

Mabit, L.; Chen, X.; Resch, C.; Toloza, A.; Meusburger, K.; Alewell, C.; Gibbs, M.; Klik, A.; Eder, A.; Strauss, P.

2016-01-01

Compound-specific stable isotope (CSSI) signatures of inherent soil organic biomarkers allow discriminating and apportioning the source of soil contribution from different land uses. Plant communities label the soil where they grow by exuding organic biomarkers. Although all plants produce the same biomarkers, the stable isotopic signature of those biomarkers is different for each plant species. For agri-environmental investigations, the CSSI technique is based on the measurement of carbon-13 ( 13 C) natural abundance signatures of specific organic compounds such as natural fatty acids (FAs) in the soil. By linking fingerprints of land use to the sediment in deposition zones, this approach has been shown to be a useful technique for determining the source of eroded soil and thereby identifying areas prone to soil degradation. The authors have used this innovative technique to investigate a 3 hectares sub-catchment of Mistelbach situated 60 km north of Vienna. Using the 137 Cs technique, Mabit et al. (2009) reported a local maximum sedimentation rate reaching 20 to 50 t ha -1 yr -1 in the lowest part of this Austrian catchment. To test the ability of the CSSI technique to discriminate different sediment sources of these deposited sediments, representative soil samples from four main agricultural fields of the site were analyzed

Comparison of Toxicity of Sediments from Rivers with Different Levels of Anthropogenic Load (Middle Volga Region, Russia Based on Elutriate and Whole Sediment Tests

Directory of Open Access Journals (Sweden)

N.Yu. Stepanova

2016-09-01

Full Text Available Description of chemical characteristics and toxicity testing of whole sediment and elutri-ate have been performed with 35 samples taken during the monitoring of rivers in the Middle Volga region (Tatarstan, Russia in 2013. The locations analyzed are sites associated with agriculture, forestry, and petroleum hydrocarbons (oil production. The toxicity tests include: (1 Chlorella vulgaris (algal elutriate test, (2 Paramecium caudatum (ciliate elutriate test, (3 Daphnia magna (cladoceran whole sediment toxicity test, and (4 Heterocypris incongruens (ostracod whole sediment toxicity test. The concentrations of metals in 43% of sediment samples have been found to exceed probable effect concentration sediment quality guidelines (SQGs. However, the concentrations of polycyclic aromatic hydrocarbons (PAHs and organochlorine pesticides have turned out to be below SQGs in most sites. The correlation analysis has shown metal toxicity to daphnid reproduction and ostracod growth (R2 = 0.34–0.64 and ammonia (R2 = 0.49–0.54. A higher percentage of samples have shown toxicity in the whole sediment tests (86% compared to the elutriate tests (54%. A total of 91% of samples have demonstrated toxicity for at least one species. Toxicity has been most frequently observed for daphnid reproduction (83% of samples and ostracod growth (56% of samples compared to daphnid (23% survival, ostracod (11% survival, and ciliate reproduction (54% or algal growth (54%. The most polluted sediments have been registered in the area of oil production. The comparison of toxicity of the samples from different types of areas has indicated that 100% of samples from the oil production area, 94% of samples from the agricultural area, and 50% of samples from the forest area were toxic to at least one test organism.

Erythrocyte Sedimentation Rate (ESR): MedlinePlus Lab Test Information

Science.gov (United States)

... K. Brunner & Suddarth's Handbook of Laboratory and Diagnostic Tests. 2 nd Ed, Kindle. Philadelphia: Wolters Kluwer Health, Lippincott Williams & Wilkins; c2014. Erythrocyte Sedimentation Rate (ESR); p. 267– ...

Elucidating Microbial Species-Specific Effects on Organic Matter Transformation in Marine Sediments

Science.gov (United States)

Mahmoudi, N.; Enke, T. N.; Beaupre, S. R.; Teske, A.; Cordero, O. X.; Pearson, A.

2017-12-01

Microbial transformation and decomposition of organic matter in sediments constitutes one of the largest fluxes of carbon in marine environments. Mineralization of sedimentary organic matter by microorganisms results in selective degradation such that bioavailable or accessible compounds are rapidly metabolized while more recalcitrant, complex compounds are preserved and buried in sediment. Recent studies have found that the ability to use different carbon sources appears to vary among microorganisms, suggesting that the availability of certain pools of carbon can be specific to the taxa that utilize the pool. This implies that organic matter mineralization in marine environments may depend on the metabolic potential of the microbial populations that are present and active. The goal of our study was to investigate the extent to which organic matter availability and transformation may be species-specific using sediment from Guaymas Basin (Gulf of California). We carried out time-series incubations using bacterial isolates and sterilized sediment in the IsoCaRB system which allowed us to measure the production rates and natural isotopic signatures (δ13C and Δ14C) of microbially-respired CO2. Separate incubations using two different marine bacterial isolates (Vibrio sp. and Pseudoalteromonas sp.) and sterilized Guaymas Basin sediment under oxic conditions showed that the rate and total quantity of organic matter metabolized by these two species differs. Approximately twice as much CO2 was collected during the Vibrio sp. incubation compared to the Pseudoalteromonas sp. incubation. Moreover, the rate at which organic matter was metabolized by the Vibrio sp. was much higher than the Pseudoalteromonas sp. indicating the intrinsic availability of organic matter in sediments may depend on the species that is present and active. Isotopic analyses of microbially respired CO2 will be used to constrain the type and age of organic matter that is accessible to each species

Testing lagoonal sediments with early life stages of the copepod Acartia tonsa (Dana): An approach to assess sediment toxicity in the Venice Lagoon

DEFF Research Database (Denmark)

Picone, Marco; Bergamin, Martina; Delaney, Eugenia

2018-01-01

between samples and control) and to investigate the possible correlation with sediment chemistry and physical properties. The results showed that statistical performances of the LDR test with A. tonsa correspond with the outcomes of other tests applied to the sediment-water interface (Strongylocentrotus...

APPLICATION OF SEDIMENT QUALITY GUIDELINES IN THE ASSESSMENT OF MANGROVE SURFACE SEDIMENT IN MENGKABONG LAGOON, SABAH, MALAYSIA

Directory of Open Access Journals (Sweden)

S. M. Praveena, M. Radojevic, M. H. Abdullah, A. Z. Aris

2008-01-01

Full Text Available There have been numerous sediment quality guidelines developed to monitor the sediments. Sediment quality guidelines are very useful to screen sediment contamination by comparing sediment contaminant concentration with the corresponding quality guideline, provide useful tools for screening sediment chemical data to identify pollutants of concern and prioritise problem sites and relatively good predictors of contaminations. However, these guidelines are chemical specific and do not include biological parameters. Aquatic ecosystems, including sediments, must be assessed in multiple components (biological data, toxicity, physicochemistry by using intregrated approaches in order to establish a complete and comprehensive set of sediment quality guidelines. Numerous sediment quality guidelines Washington Department of Ecology Sediment Quality Guideline, Australian and New Zealand Environment and Conservation Council, Swedish Environmental Sediment Quality, Screening Quick Reference Table, Portuguese Legislation on the Classification of Dredged Materials in Coastal Zones and Interim Sediment Quality Guideline for Hong Kong have been applied to the Mengkabong lagoon mangrove sediment and discussed. The most appropriate guideline that meets the prioritization criteria consistent with international initiatives and regulations is interim sediment quality values for Hong Kong. The guideline verifies that all the metals are below the Interim Sediment Quality Value-low. However, site-specific, biological testing and ecological analysis of exisiting benthics community structure related to sediment contamination are needed for final decision making in the case of Mengkabong lagoon.

21 CFR 864.6700 - Erythrocyte sedimentation rate test.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Erythrocyte sedimentation rate test. 864.6700 Section 864.6700 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES HEMATOLOGY AND PATHOLOGY DEVICES Manual Hematology Devices § 864.6700 Erythrocyte...

Preparation and characterization of nickel-spiked freshwater sediments for toxicity tests: toward more environmentally realistic nickel partitioning

Science.gov (United States)

Brumbaugh, William G.; Besser, John M.; Ingersoll, Christopher G.; May, Thomas W.; Ivey, Chris D.; Schlekat, Christian E.; Garman, Emily R.

2013-01-01

Two spiking methods were compared and nickel (Ni) partitioning was evaluated during a series of toxicity tests with 8 different freshwater sediments having a range of physicochemical characteristics. A 2-step spiking approach with immediate pH adjustment by addition of NaOH at a 2:1 molar ratio to the spiked Ni was effective in producing consistent pH and other chemical characteristics across a range of Ni spiking levels. When Ni was spiked into sediment having a high acid-volatile sulfide and organic matter content, a total equilibration period of at least 10 wk was needed to stabilize Ni partitioning. However, highest spiking levels evidently exceeded sediment binding capacities; therefore, a 7-d equilibration in toxicity test chambers and 8 volume-additions/d of aerobic overlying water were used to avoid unrealistic Ni partitioning during toxicity testing. The 7-d pretest equilibration allowed excess spiked Ni and other ions from pH adjustment to diffuse from sediment porewater and promoted development of an environmentally relevant, 0.5- to 1-cm oxic/suboxic sediment layer in the test chambers. Among the 8 different spiked sediments, the logarithm of sediment/porewater distribution coefficient values (log Kd) for Ni during the toxicity tests ranged from 3.5 to 4.5. These Kd values closely match the range of values reported for various field Ni-contaminated sediments, indicating that testing conditions with our spiked sediments were environmentally realistic.

Testing the effects of in-stream sediment sources and sinks on simulated watershed sediment yield using the coupled U.S. Army Corps of Engineers GSSHA Model and SEDLIB Sediment Transport Library

Science.gov (United States)

Floyd, I. E.; Downer, C. W.; Brown, G.; Pradhan, N. R.

2017-12-01

The Gridded Surface Subsurface Hydrologic Analysis (GSSHA) model is the US Army Corps of Engineers' (USACE)'s only fully coupled overland/in-stream sediment transport model. While the overland sediment transport formulation in GSSHA is considered state of the art, the existing in-stream sediment transport formulation is less robust. A major omission in the formulation of the existing GSSHA in-stream model is the lack of in-stream sources of fine materials. In this effort, we enhanced the in-stream sediment transport capacity of GSSHA by linking GSSHA to the SEDLIB sediment transport library. SEDLIB was developed at the Coastal and Hydraulics Laboratory (CHL) under the System Wide Water Resources Program (SWWRP) and Flood and Coastal (F&C) research program. It is designed to provide a library of sediment flux formulations for hydraulic and hydrologic models, such as GSSHA. This new version of GSSHA, with the updated in-stream sediment transport simulation capability afforded by the linkage to SEDLIB, was tested in against observations in an experimental watershed that had previously been used as a test bed for GSSHA. The results show a significant improvement in the ability to model in-stream sources of fine sediment. This improved capability will broaden the applicability of GSSHA to larger watersheds and watersheds with complex sediment dynamics, such as those subjected to fire hydrology.

Performance testing of the sediment-contaminant transport model, SERATRA, at different rivers

International Nuclear Information System (INIS)

Onishi, Y.; Yabusaki, S.B.; Kincaid, C.T.

1982-04-01

Mathematical models of sediment-contaminant migration in surface water must account for transport, intermedia transfer, decay and degradation, and transformation processes. The unsteady, two dimensional, sediment-contaminant transport code, SERATRA (Onishi, Schreiber and Codell 1980) includes these mechanisms. To assess the accuracy of SERATRA to simulate the sediment-contaminant transport and fate processes, the code was tested against one-dimensional analytical solutions, checked for its mass balance, and applied to field sites. The field application cases ranged from relatively simple, steady conditions to unsteady, nonuniform conditions for large, intermediate, and small rivers. It was found that SERATRA is capable of simulating sediment-contaminant transport under a wide range of conditions

Disturbances to metal partitioning during toxicity testing of iron(II)-rich estuarine pore waters and whole sediments.

Science.gov (United States)

Simpson, Stuart L; Batley, Graeme E

2003-02-01

Metal partitioning is altered when suboxic estuarine sediments containing Fe(II)-rich pore waters are disturbed during collection, preparation, and toxicity testing. Experiments with model Fe(II)-rich pore waters demonstrated the rates at which adsorptive losses of Cd, Cu, Ni, Mn, Pb, and Zn occur upon exposure to air. Experiments with Zn-contaminated estuarine sediments demonstrated large and often unpredictable changes to metal partitioning during sediment storage, removal of organisms, and homogenization before testing. Small modifications to conditions, such as aeration of overlying waters, caused large changes to the metal partitioning. Disturbances caused by sediment collection required many weeks for reestablishment of equilibrium. Bioturbation by benthic organisms led to oxidation of pore-water Fe(II) and lower Zn fluxes because of the formation of Fe hydroxide precipitates that adsorb pore-water Zn. For five weeks after the addition of organisms to sediments, Zn fluxes increased slowly as the organisms established themselves in the sediments, indicating that the establishment of equilibrium was not rapid. The results are discussed in terms of the dynamic nature of suboxic, Fe(II)-rich estuarine sediments, how organisms perturb their environment, and the importance of understanding chemistry in toxicity testing with whole sediments or pore water. Recommendations are provided for the handling of sediments for toxicity testing.

Estimating the in situ sediment-porewater distribution of PAHs and chlorinated aromatic hydrocarbons in anthropogenic impacted sediments

Energy Technology Data Exchange (ETDEWEB)

Hans Peter H. Arp; Gijs D. Breedveld; Gerard Cornelissen [Norwegian Geotechnical Institute (NGI), Oslo (Norway). Department of Environmental Engineering

2009-08-15

It has become increasingly apparent that the in situ sediment-porewater distribution behavior of organic compounds within anthropogenic impacted sediments is quite diverse, and challenging to generalize. Traditional models based on octanol-water partitioning generally overestimate native porewater concentrations, and modern approaches accounting for multiple carbon fractions, including black carbon, appear sediment specific. To assess the diversity of this sorption behavior, we collected all peer-reviewed total organic carbon (TOC)-normalized in situ sediment-porewater distribution coefficients, K{sub TOC}, for impacted sediments. This entailed several hundreds of data for PAHs, PCBs, PCDD/Fs, and chlorinated benzenes, covering a large variety of sediments, locations, and experimental methods. Compound-specific KTOC could range up to over 3 orders of magnitude. Output from various predictive models for individual carbonaceous phases found in impacted sediments, based on peer-reviewed polyparameter linear free energy relationships (PP-LFERs), Raoult's Law, and the SPARC online-calculator, were tested to see if any of the models could consistently predict literature K{sub TOC} values within a factor of 30 (i.e. about 1.5 orders of magnitude, or half the range of K{sub TOC} values). The Raoult's Law model and coal tar PP-LFER achieved the sought-after accuracy for all tested compound classes, and are recommended for general, regional-scale modeling purposes. As impacted sediment-porewater distribution models are unlikely to get more accurate than this, this review underpins that the only way to accurately obtain accurate porewater concentrations is to measure them directly, and not infer them from sediment concentrations. 86 refs., 2 figs., 3 tabs.

Hydraulic conductivity changes in river valley sediments caused by river bank filtration - an analysis of specific well capacity

Science.gov (United States)

Kaczmarek, Piotr M. J.

2017-06-01

Parameters from archive data of the Kalisz-Lis waterworks, located in the Prosna River valley south of Kalisz, have been analysed. Well barrier discharges groundwater from Quaternary sediments which is mixed with riverbank filtration water. The analysis focused on specific well capacity, a parameter that represents the technical and natural aspects of well life. To exclude any aging factor, an examination of specific well capacity acquired only in the first pumping tests of a new well was performed. The results show that wells drilled between 1961 and 2004 have similar values of specific well capacity and prove that > 40 years discharge has had little influence on hydrodynamic conditions of the aquifer, i.e., clogging has either not occurred or is of low intensity. This implies that, in the total water balance of the Kalisz- Lis well barrier, riverbank filtration water made little contribution. In comparison, a similar analysis of archive data on the Mosina-Krajkowo wells of two generations of well barriers located in the Warta flood plains was performed; this has revealed a different trend. There was a significant drop in specific well capacity from the first pumping test of substitute wells. Thus, long-term groundwater discharge in the Warta valley has had a great impact on the reduction of the hydraulic conductivity of sediments and has worsened hydrodynamic conditions due to clogging of river bed and aquifer, which implies a large contribution of riverbank filtration water in the total water well balance. For both well fields conclusions were corroborated by mathematical modeling; in Kalisz-Lis 16.2% of water comes from riverbank filtration, whereas the percentage for Mosina-Krajkowo is 78.9%.

Simple, specific analysis of organophosphorus and carbamate pesticides in sediments using column extraction and gas chromatography

Science.gov (United States)

Belisle, A.A.; Swineford, D.M.

1988-01-01

A simple, specific procedure was developed for the analysis of organophosphorus and carbamate pesticides in sediment. The wet soil was mixed with anhydrous sodium sulfate to bind water and the residues were column extracted in acetone:methylene chloride (1:l,v/v). Coextracted water was removed by additional sodium sulfate packed below the sample mixture. The eluate was concentrated and analyzed directly by capillary gas chromatography using phosphorus and nitrogen specific detectors. Recoveries averaged 93 % for sediments extracted shortly after spiking, but decreased significantly as the samples aged.

Distributed specific sediment yield estimations in Japan attributed to extreme-rainfall-induced slope failures under a changing climate

Directory of Open Access Journals (Sweden)

K. Ono

2011-01-01

Full Text Available The objective of this study was to estimate the potential sediment yield distribution in Japan attributed to extreme-rainfall-induced slope failures in the future. For this purpose, a regression relationship between the slope failure probability and the subsequent sediment yield was developed by using sediment yield observations from 59 dams throughout Japan. The slope failure probability accounts for the effects of topography (as relief energy, geology and hydro-climate variations (hydraulic gradient changes due to extreme rainfall variations and determines the potential slope failure occurrence with a 1-km resolution. The applicability of the developed relationship was then validated by comparing the simulated and observed sediment yields in another 43 dams. To incorporate the effects of a changing climate, extreme rainfall variations were estimated by using two climate change scenarios (the MRI-RCM20 Ver.2 model A2 scenario and the MIROC A1B scenario for the future and by accounting for the slope failure probability through the effect of extreme rainfall on the hydraulic gradient. Finally, the developed slope failure hazard-sediment yield relationship was employed to estimate the potential sediment yield distribution under a changing climate in Japan.

Time series analyses of annual sediment yields covering 15–20 years in 59 dams reveal that extreme sedimentation events have a high probability of occurring on average every 5–7 years. Therefore, the extreme-rainfall-induced slope failure probability with a five-year return period has a statistically robust relationship with specific sediment yield observations (with r² = 0.65. The verification demonstrated that the model is effective for use in simulating specific sediment yields with r² = 0.74. The results of the GCM scenarios suggest that the sediment yield issue will be critical in Japan in the future. When the spatially averaged sediment

Chromosomal abnormalities in roots of aquatic plant Elodea canadensis as a tool for testing genotoxicity of bottom sediments.

Science.gov (United States)

Zotina, Tatiana; Medvedeva, Marina; Trofimova, Elena; Alexandrova, Yuliyana; Dementyev, Dmitry; Bolsunovsky, Alexander

2015-12-01

Submersed freshwater macrophytes are considered as relevant indicators for use in bulk bottom sediment contact tests. The purpose of this study was to estimate the validity of endpoints of aquatic plant Elodea canadensis for laboratory genotoxicity testing of natural bottom sediments. The inherent level of chromosome abnormalities (on artificial sediments) in roots of E. canadensis under laboratory conditions was lower than the percentage of abnormal cells in bulk sediments from the Yenisei River. The percentage of abnormal cells in roots of E. canadensis was more sensitive to the presence of genotoxic agents in laboratory contact tests than in the natural population of the plant. The spectra of chromosomal abnormalities that occur in roots of E. canadensis under natural conditions in the Yenisei River and in laboratory contact tests on the bulk bottom sediments from the Yenisei River were similar. Hence, chromosome abnormalities in roots of E. canadensis can be used as a relevant and sensitive genotoxicity endpoint in bottom sediment-contact tests. Copyright © 2015 Elsevier Inc. All rights reserved.

Evaluation and selection of test methods for assessment of contaminated sediments in the Baltic Sea

DEFF Research Database (Denmark)

Lehtonen, Kari; Ahvo, Aino; Berezina, Nadya

The purpose of the CONTEST project (2014-15) is to test, develop, evaluate and select suitable biological methods to be applied in the quantitative and qualitative assessment of toxicity of anthropogenically contaminated sediments in the Baltic Sea marine region. Here is presented results from...... showed large variability in the sensitivity of the different biotests. Most of the tests applied showed concentration-dependent effects on the test organisms. New experiments will be carried out in 2015. The CONTEST project is funded by the Nordic Council of Ministers and the Finnish Ministry...... a set of pilot experiments, which were performed by the participating laboratories. Chemical analysis of the contaminated harbour sediment chosen as the test matrix confirmed the presence of high concentrations of polycyclic aromatic hydrocarbons, organotins and trace metals, and the sediment...

Variability in source sediment contributions by applying different statistic test for a Pyrenean catchment.

Science.gov (United States)

Palazón, L; Navas, A

2017-06-01

Information on sediment contribution and transport dynamics from the contributing catchments is needed to develop management plans to tackle environmental problems related with effects of fine sediment as reservoir siltation. In this respect, the fingerprinting technique is an indirect technique known to be valuable and effective for sediment source identification in river catchments. Large variability in sediment delivery was found in previous studies in the Barasona catchment (1509 km 2 , Central Spanish Pyrenees). Simulation results with SWAT and fingerprinting approaches identified badlands and agricultural uses as the main contributors to sediment supply in the reservoir. In this study the Kruskal-Wallis H-test and (3) principal components analysis. Source contribution results were different between assessed options with the greatest differences observed for option using #3, including the two step process: principal components analysis and discriminant function analysis. The characteristics of the solutions by the applied mixing model and the conceptual understanding of the catchment showed that the most reliable solution was achieved using #2, the two step process of Kruskal-Wallis H-test and discriminant function analysis. The assessment showed the importance of the statistical procedure used to define the optimum composite fingerprint for sediment fingerprinting applications. Copyright © 2016 Elsevier Ltd. All rights reserved.

Review of the use of Ceramium tenuicorne growth inhibition test for testing toxicity of substances, effluents, products sediment and soil

Science.gov (United States)

Eklund, Britta

2017-08-01

A growth inhibition test has been developed based on two clones of the red macroalga Ceramium tenuicorne, one originating from 7 PSU and the other from 20 PSU. The species can be adapted to different salinities and the test can be carried out between 4 and 32 PSU. This test became an ISO standard in 2010 (ISO 107 10) for testing of chemicals and water effluents. In this study new and published data has been compiled on toxicity of single substances, waste waters from pulp mills, leachates from antifouling paints, harbour sediments and soil used for maintenance of leisure boats. The results show that the alga is sensitive to both metals and organic compounds and to biocides used in antifouling paints. By testing leachates from antifouling paints these could be ranked according to their toxicity. Similarly, the toxicity of waste waters from pulp mills was determined and the efficiency of secondary treatment evaluated. Further, the test method proved useful to test the toxicity in sediment samples. Sediments from small town harbours and ship lanes were shown to be harmful and compounds originating from antifouling paints were responsible for a large part of the inhibiting effect. The alga proved to be sensitive to contaminants leaking from boat yard soil. The growth inhibition test is a robust test that has high repeatability and reproducibility and easily can be applied on water, soil and sediment samples without being too costly. The species is found worl-wide in temperate waters, which makes the results relevant for large areas. In the Baltic Sea C. tenuicorne is the most common red alga species and is thus particularly relevant for this area. The overall results show that contaminants from boat activities and the use of antifouling paints in particular pose a threat to the environment.

Chronic toxicity of nickel-spiked freshwater sediments: variation in toxicity among eight invertebrate taxa and eight sediments

Science.gov (United States)

Besser, John M.; Brumbaugh, William G.; Ingersoll, Christopher G.; Ivey, Chris D.; Kunz, James L.; Kemble, Nile E.; Schlekat, Christian E.; Garman, Emily R.

2013-01-01

This study evaluated the chronic toxicity of Ni-spiked freshwater sediments to benthic invertebrates. A 2-step spiking procedure (spiking and sediment dilution) and a 2-stage equilibration period (10 wk anaerobic and 1 wk aerobic) were used to spike 8 freshwater sediments with wide ranges of acid-volatile sulfide (AVS; 0.94–38 µmol/g) and total organic carbon (TOC; 0.42–10%). Chronic sediment toxicity tests were conducted with 8 invertebrates (Hyalella azteca, Gammarus pseudolimnaeus, Chironomus riparius, Chironomus dilutus, Hexagenia sp., Lumbriculus variegatus, Tubifex tubifex, and Lampsilis siliquoidea) in 2 spiked sediments. Nickel toxicity thresholds estimated from species-sensitivity distributions were 97 µg/g and 752 µg/g (total recoverable Ni; dry wt basis) for sediments with low and high concentrations of AVS and TOC, respectively. Sensitive species were tested with 6 additional sediments. The 20% effect concentrations (EC20s) for Hyalella and Gammarus, but not Hexagenia, were consistent with US Environmental Protection Agency benchmarks based on Ni in porewater and in simultaneously extracted metals (SEM) normalized to AVS and TOC. For Hexagenia, sediment EC20s increased at less than an equimolar basis with increased AVS, and toxicity occurred in several sediments with Ni concentrations in SEM less than AVS. The authors hypothesize that circulation of oxygenated water by Hexagenia led to oxidation of AVS in burrows, creating microenvironments with high Ni exposure. Despite these unexpected results, a strong relationship between Hexagenia EC20s and AVS could provide a basis for conservative site-specific sediment quality guidelines for Ni.

Comparative Test Case Specification

DEFF Research Database (Denmark)

Kalyanova, Olena; Heiselberg, Per

 This document includes a definition of the comparative test cases DSF200_3 and DSF200_4, which previously described in the comparative test case specification for the test cases DSF100_3 and DSF200_3 [Ref.1]....... This document includes a definition of the comparative test cases DSF200_3 and DSF200_4, which previously described in the comparative test case specification for the test cases DSF100_3 and DSF200_3 [Ref.1]....

Urine specific gravity test

Science.gov (United States)

... medlineplus.gov/ency/article/003587.htm Urine specific gravity test To use the sharing features on this page, please enable JavaScript. Urine specific gravity is a laboratory test that shows the concentration ...

First use of a compound-specific stable isotope (CSSI) technique to trace sediment transport in upland forest catchments of Chile.

Science.gov (United States)

Bravo-Linares, Claudio; Schuller, Paulina; Castillo, Alejandra; Ovando-Fuentealba, Luis; Muñoz-Arcos, Enrique; Alarcón, Oscar; de Los Santos-Villalobos, Sergio; Cardoso, Renan; Muniz, Marcelo; Meigikos Dos Anjos, Roberto; Bustamante-Ortega, Ramón; Dercon, Gerd

2018-03-15

Land degradation is a problem affecting the sustainability of commercial forest plantations. The identification of critical areas prone to erosion can assist this activity to better target soil conservation efforts. Here we present the first use of the carbon-13 signatures of fatty acids (C14 to C24) in soil samples for spatial and temporal tracing of sediment transport in river bodies of upland commercial forest catchments in Chile. This compound-specific stable isotope (CSSI) technique was tested as a fingerprinting approach to determine the degree of soil erosion in pre-harvested forest catchments with surface areas ranging from 12 to 40ha. For soil apportionment a mixing model based on a Bayesian inference framework was used (CSSIAR v.2.0). Approximately four potential sediment sources were used for the calculations of all of the selected catchments. Unpaved forestry roads were shown to be the main source of sediment deposited at the outlet of the catchments (30-75%). Furthermore, sampling along the stream channel demonstrated that sediments were mainly comprised of sediment coming from the unpaved roads in the upper part of the catchments (74-98%). From this it was possible to identify the location and type of primary land use contributing to the sediment delivered at the outlet of the catchments. The derived information will allow management to focus efforts to control or mitigate soil erosion by improving the runoff features of the forest roads. The use of this CSSI technique has a high potential to help forestry managers and decision makers to evaluate and mitigate sources of soil erosion in upland forest catchments. It is important to highlight that this technique can also be a good complement to other soil erosion assessment and geological fingerprinting techniques, especially when attempting to quantify (sediment loads) and differentiate which type of land use most contributes to sediment accumulation. Copyright © 2017 Elsevier B.V. All rights reserved.

Comparative genotoxicity testing of Rhine river sediment extracts using the comet assay with permanent fish cell lines (RTG-2 and RTL-W1) and the Ames test

Energy Technology Data Exchange (ETDEWEB)

Kosmehl, T.; Braunbeck, T.; Hollert, H. [Dept. of Zoology, Aquatic Ecology and Toxicology Section, Univ. of Heidelberg (Germany); Krebs, F.; Manz, W. [German Federal Inst. of Hydrology, Koblenz (Germany); Erdinger, L. [Dept. for Hygiene and Medical Microbiology, Inst. for Hygiene, Univ. of Heidelberg (Germany)

2004-07-01

Whilst at least in Germany assessment strategies on the basis of chemical analysis and acute toxicity data dominated the last decades, the development of more specific biological endpoints and biomarkers in ecotoxicology is required in order to arrive at a good ecological potential and good chemical status of surface waters in the European river basins until the year 2015, as required by the European Water Framework Directive. Since sediments have for long been known to function both as a sink and as a source of pollutants in aquatic systems, and since part of the particle-associated substances have frequently been demonstrated to cause mutagenic and carcinogenic effects in aquatic organisms, particularly in fish, there is, among other requirements, an urgent need to develop, standardize and implement integrated vertebrate-based test systems addressing genotoxicity into recent sediment investigation strategies. Thus, the present study was designed to compare the suitability of two commonly used test systems, the comet assay and the Ames test, for the evaluation of the ecotoxicological burden of surface and core sediment samples from the river Rhine. Methods (or main features). In order to determine the importance of inherent enzymatic activities, two permanent fish cell lines with different biotransformation capacities, RTL-W1 and RTG-2, were compared with respect to their capability of detecting genotoxic effects in 18 surface and core sediment samples from 9 locations along the river Rhine in the comet assay with and without exogenous bioactivation. For further comparison, as a prokaryotic mutagenicity assay, the Salmonella plate incorporation assay (Ames test) with the test strains TA98 and TA100 with and without exogenous metabolic activation was used. Results and discussion. Whereas all sediment extracts induced genotoxic effects in the comet assay with RTL-W1 cells, only 12 out of 18 sediment extracts revealed significant genotoxicity in the tests with the

Characterizing toxicity of metal-contaminated sediments from mining areas

International Nuclear Information System (INIS)

Besser, John M.; Brumbaugh, William G.; Ingersoll, Christopher G.

2015-01-01

Highlights: • We review methods for testing toxicity of sediments affected by metals. • Toxicity testing provides site-specific assessment of impacts on resident biota. • Goals are to document extent of toxicity and associations with metal exposure. • Need to characterize bioavailability of metals in sediment and pore water. • Toxicity data is basis for guidelines used to predict hazards of metal toxicity. - Abstract: This paper reviews methods for testing the toxicity of metals associated with freshwater sediments, linking toxic effects with metal exposure and bioavailability, and developing sediment quality guidelines. The most broadly applicable approach for characterizing metal toxicity is whole-sediment toxicity testing, which attempts to simulate natural exposure conditions in the laboratory. Standard methods for whole-sediment testing can be adapted to test a wide variety of taxa. Chronic sediment tests that characterize effects on multiple endpoints (e.g., survival, growth, and reproduction) can be highly sensitive indicators of adverse effects on resident invertebrate taxa. Methods for testing of aqueous phases (pore water, overlying water, or elutriates) are used less frequently. Analysis of sediment toxicity data focuses on statistical comparisons between responses in sediments from the study area and responses in one or more uncontaminated reference sediments. For large or complex study areas, a greater number of reference sediments is recommended to reliably define the normal range of responses in uncontaminated sediments – the ‘reference envelope’. Data on metal concentrations and effects on test organisms across a gradient of contamination may allow development of concentration-response models, which estimate metal concentrations associated with specified levels of toxic effects (e.g. 20% effect concentration or EC20). Comparisons of toxic effects in laboratory tests with measures of impacts on resident benthic invertebrate

Estimating Western U.S. Reservoir Sedimentation

Science.gov (United States)

Bensching, L.; Livneh, B.; Greimann, B. P.

2017-12-01

Reservoir sedimentation is a long-term problem for water management across the Western U.S. Observations of sedimentation are limited to reservoir surveys that are costly and infrequent, with many reservoirs having only two or fewer surveys. This work aims to apply a recently developed ensemble of sediment algorithms to estimate reservoir sedimentation over several western U.S. reservoirs. The sediment algorithms include empirical, conceptual, stochastic, and processes based approaches and are coupled with a hydrologic modeling framework. Preliminary results showed that the more complex and processed based algorithms performed better in predicting high sediment flux values and in a basin transferability experiment. However, more testing and validation is required to confirm sediment model skill. This work is carried out in partnership with the Bureau of Reclamation with the goal of evaluating the viability of reservoir sediment yield prediction across the western U.S. using a multi-algorithm approach. Simulations of streamflow and sediment fluxes are validated against observed discharges, as well as a Reservoir Sedimentation Information database that is being developed by the US Army Corps of Engineers. Specific goals of this research include (i) quantifying whether inter-algorithm differences consistently capture observational variability; (ii) identifying whether certain categories of models consistently produce the best results, (iii) assessing the expected sedimentation life-span of several western U.S. reservoirs through long-term simulations.

Toxicity of sediments potentially contaminated by coal mining and natural gas extraction to unionid mussels and commonly tested benthic invertebrates

Science.gov (United States)

Wang, Ning; Ingersoll, Christopher G.; Kunz, James L.; Brumbaugh, William G.; Kane, Cindy M.; Evans, R. Brian; Alexander, Steven; Walker, Craig; Bakaletz, Steve

2013-01-01

Sediment toxicity tests were conducted to assess potential effects of contaminants associated with coal mining or natural gas extraction activities in the upper Tennessee River basin and eastern Cumberland River basin in the United States. Test species included two unionid mussels (rainbow mussel, Villosa iris, and wavy-rayed lampmussel, Lampsilis fasciola, 28-d exposures), and the commonly tested amphipod, Hyalella azteca (28-d exposure) and midge, Chironomus dilutus (10-d exposure). Sediments were collected from seven test sites with mussel communities classified as impacted and in proximity to coal mining or gas extraction activities, and from five reference sites with mussel communities classified as not impacted and no or limited coal mining or gas extraction activities. Additional samples were collected from six test sites potentially with high concentrations of polycyclic aromatic hydrocarbons (PAHs) and from a test site contaminated by a coal ash spill. Mean survival, length, or biomass of one or more test species was reduced in 10 of 14 test samples (71%) from impacted areas relative to the response of organisms in the five reference samples. A higher proportion of samples was classified as toxic to mussels (63% for rainbow mussels, 50% for wavy-rayed lampmussels) compared with amphipods (38%) or midge (38%). Concentrations of total recoverable metals and total PAHs in sediments did not exceed effects-based probable effect concentrations (PECs). However, the survival, length, or biomasses of the mussels were reduced significantly with increasing PEC quotients for metals and for total PAHs, or with increasing sum equilibrium-partitioning sediment benchmark toxic units for PAHs. The growth of the rainbow mussel also significantly decreased with increasing concentrations of a major anion (chloride) and major cations (calcium and magnesium) in sediment pore water. Results of the present study indicated that (1) the findings from laboratory tests were generally

Organotin persistence in contaminated marine sediments and porewaters: In situ degradation study using species-specific stable isotopic tracers

Energy Technology Data Exchange (ETDEWEB)

Furdek, Martina; Mikac, Nevenka [Division for Marine and Environmental Research, Rudjer Boskovic Institute, Bijenicka 54, Zagreb (Croatia); Bueno, Maite; Tessier, Emmanuel; Cavalheiro, Joana [Laboratoire de Chimie Analytique Bio-inorganique et Environnement, Institut Pluridisciplinaire de Recherche sur l’Environnement et les Matériaux, CNRS UMR 5254, Université de Pau et des Pays de l’Adour, Hélioparc Pau Pyrénées, 2, Av. P. Angot, 64053 Pau Cedex 9 (France); Monperrus, Mathilde, E-mail: mathilde.monperrus@univ-pau.fr [Laboratoire de Chimie Analytique Bio-inorganique et Environnement, Institut Pluridisciplinaire de Recherche sur l’Environnement et les Matériaux, CNRS UMR 5254, Université de Pau et des Pays de l’Adour, Hélioparc Pau Pyrénées, 2, Av. P. Angot, 64053 Pau Cedex 9 (France)

2016-04-15

Highlights: • Limiting step in OTC degradation in sediments is their desorption into porewater. • TBT persistence in contaminated sediments increases in sediments rich in organic matter. • DBT does not accumulate in sediments as degradation product of TBT. • TBT and DBT degradation in porewaters occurs with half-lives from 2.9 to 9.2 days. • PhTs degradation is slower than BuTs degradation in oxic porewaters. - Abstract: This paper provides a comprehensive study of the persistence of butyltins and phenyltins in contaminated marine sediments and presents the first data on their degradation potentials in porewaters. The study’s aim was to explain the different degradation efficiencies of organotin compounds (OTC) in contaminated sediments. The transformation processes of OTC in sediments and porewaters were investigated in a field experiment using species-specific, isotopically enriched organotin tracers. Sediment characteristics (organic carbon content and grain size) were determined to elucidate their influence on the degradation processes. The results of this study strongly suggest that a limiting step in OTC degradation in marine sediments is their desorption into porewaters because their degradation in porewaters occurs notably fast with half-lives of 9.2 days for tributyltin (TBT) in oxic porewaters and 2.9 ± 0.1 and 9.1 ± 0.9 days for dibutyltin (DBT) in oxic and anoxic porewaters, respectively. By controlling the desorption process, organic matter influences the TBT degradation efficiency and consequently defines its persistence in contaminated sediments, which thus increases in sediments rich in organic matter.

Organotin persistence in contaminated marine sediments and porewaters: In situ degradation study using species-specific stable isotopic tracers

International Nuclear Information System (INIS)

Furdek, Martina; Mikac, Nevenka; Bueno, Maite; Tessier, Emmanuel; Cavalheiro, Joana; Monperrus, Mathilde

2016-01-01

Highlights: • Limiting step in OTC degradation in sediments is their desorption into porewater. • TBT persistence in contaminated sediments increases in sediments rich in organic matter. • DBT does not accumulate in sediments as degradation product of TBT. • TBT and DBT degradation in porewaters occurs with half-lives from 2.9 to 9.2 days. • PhTs degradation is slower than BuTs degradation in oxic porewaters. - Abstract: This paper provides a comprehensive study of the persistence of butyltins and phenyltins in contaminated marine sediments and presents the first data on their degradation potentials in porewaters. The study’s aim was to explain the different degradation efficiencies of organotin compounds (OTC) in contaminated sediments. The transformation processes of OTC in sediments and porewaters were investigated in a field experiment using species-specific, isotopically enriched organotin tracers. Sediment characteristics (organic carbon content and grain size) were determined to elucidate their influence on the degradation processes. The results of this study strongly suggest that a limiting step in OTC degradation in marine sediments is their desorption into porewaters because their degradation in porewaters occurs notably fast with half-lives of 9.2 days for tributyltin (TBT) in oxic porewaters and 2.9 ± 0.1 and 9.1 ± 0.9 days for dibutyltin (DBT) in oxic and anoxic porewaters, respectively. By controlling the desorption process, organic matter influences the TBT degradation efficiency and consequently defines its persistence in contaminated sediments, which thus increases in sediments rich in organic matter.

Amphipod and Sea Urchin tests to assess the toxicity of Mediterranean sediments: the case of Portmán Bay

Directory of Open Access Journals (Sweden)

A. Cesar

2004-04-01

Full Text Available The sediment formed by the tailings of an abandoned mine, which discharged into Portmán Bay, Murcia, SE-Spain, was tested to establish a possible gradient of heavy metals. The results were compared with tolerance limits of what was calculated from control sites. Whole sediment toxicity tests were performed on two amphipod species, Gammarus aequicauda and Microdeutopus gryllotalpa, while sediment-water interface and porewater toxicity tests were performed on three sea urchins species, Arbacia lixula, Paracentrotus lividus and Sphaerechinus granularis. The sensitivity of these marine organisms was evaluated by exposure tests using the reference substances: ammonium chloride (NH4Cl, cadmium chloride (CdCl2, potassium dichromate (K2Cr2O7, sodium dodecyl sulfate (C12H25NaO4S and zinc sulfate (ZnSO4. The concentration of heavy metals decreased along the pollution gradient. Amphipod 10 day acute toxicity tests clearly demonstrated the gradient of toxicity. The sediment-water interface tests conducted with sea urchins also pointed to a pollution gradient and were more sensitive than the tests involving amphipods.

Duckweed Lemna minor as a tool for testing toxicity of coal residues and polluted sediments

Energy Technology Data Exchange (ETDEWEB)

Jenner, H.A.; Janssen-Mommen, J.P.M. (Kema Environmental Services, Arnhem (Netherlands))

1993-07-01

Duckweed, Lemna minor, was used for testing single elements and leachates of coal ashes and sediments by expressing growth as surface coverage. The EC50 for the elements Cd, Cu, Zn, As(III), As(V), Se(IV), Se(VI), SeO[sub 2] were 0.86, 2.2, 4.4, 8.4, 297, 21, 67, 37 [mu]M respectively. Leachates were tested of pulverized coal fuel ash (PFA), including 'low NO[sub x]' ashes, coal gasification slag (CGS), and, as a reference, the polluted sediments of a canal. The concentrations of elements in leachates of 'low NO[sub x]' PFA were higher than those in leachates of conventional PFA. The leaching of anions from PFA was quicker than the cations. CGS showed an absolutely minimal element leaching. Comparison of the effects of conventional PFA with sediments from Rotterdam harbor, River Rhine, and the canal shows PFA to be the far less toxic one. The sediment samples from the canal demonstrated strong growth inhibition, probably due to high zinc concentrations originating from industrial activity.

Duckweed Lemna minor as a tool for testing toxicity of coal residues and polluted sediments

Energy Technology Data Exchange (ETDEWEB)

Jenner, H A; Janssen-Mommen, J P.M. [Kema Environmental Services, Arnhem (Netherlands)

1993-07-01

Duckweed, Lemna minor, was used for testing single elements and leachates of coal ashes and sediments by expressing growth as surface coverage. The EC50 for the elements Cd, Cu, Zn, As(III), As(V), Se(IV), Se(VI), SeO[sub 2] were 0.86, 2.2, 4.4, 8.4, 297, 21, 67, 37 [mu]M respectively. Leachates were tested of pulverized coal fuel ash (PFA), including 'low NO[sub x]' ashes, coal gasification slag (CGS), and, as a reference, the polluted sediments of a canal. The concentrations of elements in leachates of 'low NO[sub x]' PFA were higher than those in leachates of conventional PFA. The leaching of anions from PFA was quicker than the cations. CGS showed an absolutely minimal element leaching. Comparison of the effects of conventional PFA with sediments from Rotterdam harbor, River Rhine, and the canal shows PFA to be the far less toxic one. The sediment samples from the canal demonstrated strong growth inhibition, probably due to high zinc concentrations originating from industrial activity.

Kato-Katz and Lumbreras rapid sedimentation test to evaluate helminth prevalence in the setting of a school-based deworming program

Science.gov (United States)

Lopez, Martha; Morales, Maria Luisa; Konana, Monisha; Hoyer, Paige; Pineda-Reyes, Roberto; White, Arthur Clinton; Garcia, Hector Hugo; Lescano, Andres Guillermo; Gotuzzo, Eduardo; Cabada, Miguel Mauricio

2016-01-01

The sensitivity of the Kato-Katz test is suboptimal for the evaluation of intestinal helminth prevalence. Moreover, during mass deworming, as helminth egg burden decreases, the sensitivity is likely to decrease. The Lumbreras rapid sedimentation (Lumbreras) is a low-cost non-quantitative test, but may provide useful information in low burden areas. We compared the prevalence of intestinal helminth infections assessed by the Kato-Katz and the Lumbreras rapid sedimentation test on 3 stool specimens from each of 1083 children. The sensitivities were compared using the McNemar paired test. Using the combined outcome of the 3 different stool tests as the standard, Kato-Katz had lower sensitivity than Lumbreras rapid sedimentation tests for Ascaris lumbricoides (85.1% vs. 95.1%, p = 0.03), Hymenolepis nana (77.7% vs. 97.9%, p Lumbreras rapid sedimentation tests enables the detection of more intestinal helminths infections in post-deworming low prevalence areas. PMID:27376503

Towards more ecological relevance in sediment toxicity testing with fish: Evaluation of multiple bioassays with embryos of the benthic weatherfish (Misgurnus fossilis).

Science.gov (United States)

Schreiber, Benjamin; Fischer, Jonas; Schiwy, Sabrina; Hollert, Henner; Schulz, Ralf

2018-04-01

The effects of sediment contamination on fish are of high significance for the protection of ecosystems, human health and economy. However, standardized sediment bioassays with benthic fish species, that mimic bioavailability of potentially toxic compounds and comply with the requirements of alternative test methods, are still scarce. In order to address this issue, embryos of the benthic European weatherfish (Misgurnus fossilis) were exposed to freeze-dried sediment (via sediment contact assays (SCA)) and sediment extracts (via acute fish embryo toxicity tests) varying in contamination level. The extracts were gained by accelerated solvent extraction with (i) acetone and (ii) pressurized hot water (PHWE) and subsequently analyzed for polycyclic aromatic hydrocarbons, polychlorinated biphenyls and polychlorinated dibenzodioxins and dibenzofurans. Furthermore, embryos of the predominately used zebrafish (Danio rerio) were exposed to extracts from the two most contaminated sediments. Results indicated sufficient robustness of weatherfish embryos towards varying test conditions and sensitivity towards relevant sediment-bound compounds. Furthermore, a compliance of effect concentrations derived from weatherfish embryos exposed to sediment extracts (96h-LC 50 ) with both measured gradient of sediment contamination and previously published results was observed. In comparison to zebrafish, weatherfish embryos showed higher sensitivity to the bioavailability-mimicking extracts from PHWE but lower sensitivity to extracts gained with acetone. SCAs conducted with weatherfish embryos revealed practical difficulties that prevented an implementation with three of four sediments tested. In summary, an application of weatherfish embryos, using bioassays with sediment extracts from PHWE might increase the ecological relevance of sediment toxicity testing: it allows investigations using benthic and temperate fish species considering both bioavailable contaminants and animal welfare

Quick, portable toxicity testing of marine or terrigenous fluids, sediments, or chemicals with bioluminescent organism

International Nuclear Information System (INIS)

Sabate, R.W.; Stiffey, A.V.; Dewailly, E.L.

1995-01-01

A hand-held, battery-operated instrument, which measures bioluminescence inhibition of the microscopic marine dinoflagellate Pyrocystis lunula, is capable of field-testing substances for toxicity. The organism is sensitive to ppb of strong toxicants. It tolerates some solvents in concentrations necessary for testing lipophylic samples. A test consumes only micrograms of sample. This method requires no adjustments for salinity, pH, color, or turbidity. It has been used successfully to test oil-well drilling fluids, brines produced with oil, waters and sediments from streams and lakes and petroleum-plant effluents containing contaminants such as benzene. The test is non-specific; however, if the substance is known, the end-point effects a direct measurement of its concentration. One-hour toxicity screening tests in the field produce results comparable to the standard four-hour laboratory test. Keeping the sample in the dark during incubation and testing, together with shortness of the overall procedure, eliminates anomalies from light-sensitive substances. Day-to-day variation, as well as among test replicates, is less than 10%. This quick method yields results comparable with a quick test that uses Photobacterium phosphoria, and with 96-hour tests that use Mysidopsis bahia, Artemia salina, Gonyaulax polyedra, Pimephales promelas, Ceriodaphnia dubia, and Cyprinodon variegatus

Larval development ratio test with the calanoid copepod Acartia tonsa as a new bioassay to assess marine sediment quality.

Science.gov (United States)

Buttino, Isabella; Vitiello, Valentina; Macchia, Simona; Scuderi, Alice; Pellegrini, David

2018-03-01

The copepod Acartia tonsa was used as a model species to assess marine sediment quality. Acute and chronic bioassays, such as larval development ratio (LDR) and different end-points were evaluated. As a pelagic species, A. tonsa is mainly exposed to water-soluble toxicants and bioassays are commonly performed in seawater. However, an interaction among A. tonsa eggs and the first larval stages with marine sediments might occur in shallow water environments. Here we tested two different LDR protocols by incubating A. tonsa eggs in elutriates and sediments coming from two areas located in Tuscany Region (Central Italy): Livorno harbour and Viareggio coast. The end-points analyzed were larval mortality (LM) and development inhibition (DI) expressed as the percentage of copepods that completed the metamorphosis from nauplius to copepodite. Aims of this study were: i) to verify the suitability of A. tonsa copepod for the bioassay with sediment and ii) to compare the sensitivity of A. tonsa exposed to different matrices, such as water and sediment. A preliminary acute test was also performed. Acute tests showed the highest toxicity of Livorno's samples (two out of three) compared to Viareggio samples, for which no effect was observed. On the contrary, LDR tests with sediments and elutriates revealed some toxic effects also for Viareggio's samples. Results were discussed with regards to the chemical characterization of the samples. Our results indicated that different end-points were affected in A. tonsa, depending on the matrices to which the copepods were exposed and on the test used. Bioassays with elutriates and sediments are suggested and LDR test could help decision-makers to identify a more appropriate management of dredging materials. Copyright © 2017 Elsevier Inc. All rights reserved.

Testing the potential for improving quality of sediments impacted by mussel farms using bioturbating polychaete worms

DEFF Research Database (Denmark)

Bergström, Per; Carlsson, Marita S; Lindegarth, Mats

2017-01-01

Biodeposits from farmed mussels severely influence the biogeochemistry of sediments by increasing the levels of organic matter (OM). Mitigation of such negative impacts is important for the development of sustainable aquaculture operations. As a step towards developing methods for remediation...... of coastal sediments affected by mussel farming, the effects of the polychaete, Hediste diversicolor was evaluated experimentally. In a series of field- and laboratory experiments we tested hypotheses about the effects of polychaetes on sediment oxygen consumption, nutrient fluxes and sulphide pools under...... different polychaete densities and sedimentation regimes. The experimental results support the idea that polychaetes can mitigate negative effects on the benthic environment beneath mussel farms. H. diversicolor oxidized the sediment and generally enhanced the oxygen consumption, and thus the decomposition...

Congener-specific model for polychlorinated biphenyl effect on otter (Lutra lutra) and associated sediment quality criteria

NARCIS (Netherlands)

Traas, T.P.; Luttik, R.; Klepper, O.; Beurskens, J.E.M.; Smit, M.D.; Leonards, P.E.G.; Hattum, van A.G.M.; Aldenberg, T.

2001-01-01

A model for risk assessment was built for simultaneous, congener-specific PCB bioaccumulation from sediment to fish to otters (Lutra lutra). Toxic equivalence factors (TEFs) were used to sum individual congeners in otters to a toxic equivalent concentration (TEQ) relative to

Total and species-specific quantitative analyses of trace elements in sediment by isotope dilution inductively coupled plasma mass spectrometry

International Nuclear Information System (INIS)

Inagaki, Kazumi; Takatsu, Akiko; Yarita, Takashi; Okamoto, Kensaku; Chiba, Koichi

2009-01-01

Isotope dilution inductively coupled plasma mass spectrometry (ID-ICP-MS) is one of the reliable methods for total and species-specific quantitative analysis of trace elements. However, several technical problems (e.g. spectral interference caused from sample constituents) should be overcome to obtain reliable analytical results when environmental samples are analyzed by ID-ICP-MS. In our laboratory, various methods based on ID-ICP-MS have been investigated for reliable quantitative analyses of trace elements in environmental samples. In this paper, coprecipitate separation/ID-ICP-MS for the determination of trace elements in sediment, cation exchange disk filtration/ID-ICP-MS for the determination of selenium in sediment, species-specific ID-ICP-MS using 118 Sn/labeled organotin compounds for the determination of butyltins and phenyltins, and the application of the ID-ICP-MS methods to the certification of sediment reference materials are described. (author)

The application of plant tests for sediment evaluation; Der Einsatz von Pflanzentests bei der Sedimentbewertung

Energy Technology Data Exchange (ETDEWEB)

Feiler, U. [Bundesanstalt fuer Gewaesserkunde, Koblenz (Germany); Claus, E. [Bundesanstalt fuer Gewaesserkunde, Berlin (Germany); Heininger, P. [Bundesanstalt fuer Gewaesserkunde, Koblenz (Germany); Bundesanstalt fuer Gewaesserkunde, Berlin (Germany)

2002-07-01

The aim of the present study is to demonstrate that the use of higher plants in biotests for analyses of anthropogenically contaminated sediments yields valuable results, which may be included in a concept for the integrated assessment of waters. The results of this study prove that the selected aquatic plant, Lemna minor, is basically able to indicate contamination. In the aquatic test of the sediment extracts, it showed weak, but very selective, responses to certain classes of contaminants. Fractionating of the sample and subsequent chemical analysis combined with toxicity tests allow to narrow down the groups of substances causing toxic effects. This toxicity was confirmed by analyses of the pore waters and whole sediment samples. Together with other toxicity tests (e.g. standardized bioassays) and combined with biological benthos examinations, an overall judgment can be given for the integrated assessment of waters. (orig.) [German] Ziel der hier vorgestellten Untersuchungen war es zu zeigen, dass der Einsatz von hoeheren Pflanzen in Biotests zur Untersuchung anthropogenen belasteter Sedimente wertvolle Ergebnisse liefert, die in einem Konzept zur integrierten Gewaesserbewertung verwendet werden koennen. Die Ergebnisse dieser Arbeit machen deutlich, dass die ausgewaehlte Wasserpflanze Lemna minor Schadstoffbelastungen grundsaetzlich anzeigt. Im aquatischen Test der Sedimentextrakte weist sie eine zwar schwache, aber sehr selektive Reaktion auf bestimmte Schadstoffklassen auf. Die Fraktionierung der Probe mit anschliessender Stoffanlayse kombiniert mit Toxizitaetstests erlaubt die Eingrenzung der toxisch wirksamen Stoffgruppen. Diese toxische Belastung wurde durch die Porenwasser- und Gesamtsedimentuntersuchung bestaetigt. Zusammen mit weiteren Toxizitaetstests (z.B. standardisierte Biotests) und in Kombination mit benthosbiologischen Untersuchngen ergibt sich eine Gesamtaussage zur integrierten Gewaesserbewertung. (orig.)

Ecotoxiocological Studies of Niger Delta Sediments using Duckweed (L. Minor) Growth Inhibition Test

International Nuclear Information System (INIS)

Olajire, A. A.; Alternburger, R.; Brack, W.

2003-01-01

This study was undertaken to evaluate the toxicity of sediments collected from the Niger Delta (Nigeria) to Lemna minor, a sensitive aquatic weed regularly used for ecotoxicological studies. Also, the study wanted to determine if L. minor can be used as an effective bioassay organism by oil companies and chemical industries in Nigeria. Essentially, the experimental approach involved exposure of L. minor under standard laboratory conditions to sediments and toxicity is presented as percent inhibition of growth of L. minor cultures after 7 days. The result of the present study showed that there is differential toxicity among the sediments analyzed, and we found that for 0.25mg/ml of growth rate (%1) decreases in the order: SDOGN(42.6%) >SDWRR (33.7%)> SDALD (20.5%) >SDUGBO (17.1%) ? SDWRR were clorotic and had lost their roots, indicating the very high toxicity of the soluble organic contaminants in these sediments. Lemna minor proved to be a practical bioassay organism because the L. minor toxicity test is simple, sensitive and cost effective

Prostate-Specific Antigen (PSA) Test: MedlinePlus Lab Test Information

Science.gov (United States)

... medlineplus.gov/labtests/prostatespecificantigenpsatest.html Prostate-Specific Antigen (PSA) Test To use the sharing features on this ... enable JavaScript. What is a prostate-specific antigen (PSA) test? A prostate-specific antigen (PSA) test measures ...

Effects of Feeding Strategy, Sediment Characteristics, and Chemical Properties on Polychlorinated Biphenyl and Polybrominated Diphenyl Ether Bioaccumulation from Marine Sediments in Two Invertebrates.

Science.gov (United States)

Frouin, H; Jackman, P; Dangerfield, N D; Ross, P S

2017-08-01

Shellfish and sediment invertebrates have been widely used to assess pollution trends over space and time in coastal environments around the world. However, few studies have compared the bioaccumulation potential of different test species over a range of sediment-contaminant concentrations and profiles. The bioavailability of sediment-related contaminants was evaluated using sediments collected from sites (n = 12) throughout the Salish Sea, British Columbia, Canada. Two benthic marine invertebrates-the Baltic clam Macoma balthica and the polychaete worm Neanthes arenaceodentata-were exposed for 28 days in a controlled environment to these field-collected coastal sediments. The congener-specific uptake of legacy polychlorinated biphenyls (PCBs) and emergent polybrominated diphenyl ethers (PBDEs) was determined using high-resolution gas chromatography/mass spectrometry in sediments and in invertebrates after the experimental exposure. The polychaete Neanthes accumulated lower concentrations of PCBs but higher concentrations of PBDEs. The present study indicates that differences in bioaccumulation between these two invertebrates shape the accumulation of PCB and PBDE congeners, reflect differences in feeding strategies, and reveal the physicochemical properties of the contaminants and sediment properties. Because biota-sediment accumulation factor values are often calculated for environmental monitoring or site-specific impact assessments, our results provide insight into potentially confounding factors and the need for caution when selecting indicator species for coastal marine pollution.

Radionuclide transport in the "sediments - water - plants" system of the water bodies at the Semipalatinsk test site.

Science.gov (United States)

Aidarkhanova, A K; Lukashenko, S N; Larionova, N V; Polevik, V V

2018-04-01

This paper provides research data on levels and character of radionuclide contamination distribution in the «sediments- water - plants » system of objects of the Semipalatinsk test site (STS). As the research objects there were chosen water bodies of man-made origin which located at the territory of "Experimental Field", "Balapan", "Telkem" and "Sary-Uzen" testing sites. For research the sampling of bottom sediments, water, lakeside and water plants was taken. Collected samples were used to determine concentration of anthropogenic radionuclides 90 Sr, 239+240 Pu, 241 Am, 137 Cs. The distribution coefficient (K d ) was calculated as the ratio of the content of radionuclides in the sediments to the content in water, and the concentration ratio (F V ) was calculated as the ratio of radionuclide content in plants to the content in sediments or soil. Copyright © 2018 Elsevier Ltd. All rights reserved.

Agar Sediment Test for Assessing the Suitability of Organic Waste Streams for Recovering Nutrients by the Aquatic Worm Lumbriculus variegatus.

Directory of Open Access Journals (Sweden)

Bob Laarhoven

Full Text Available An agar sediment test was developed to evaluate the suitability of organic waste streams from the food industry for recovering nutrients by the aquatic worm Lumbriculus variegatus (Lv. The effects of agar gel, sand, and food quantities in the sediment test on worm growth, reproduction, and water quality were studied. Agar gel addition ameliorated growth conditions by reducing food hydrolysis and altering sediment structure. Best results for combined reproduction and growth were obtained with 0.6% agar-gel (20 ml, 10 g. fine sand, 40 g. coarse sand, and 105 mg fish food (Tetramin. With agar gel, ingestion and growth is more the result of addition of food in its original quality. Final tests with secondary potato starch sludge and wheat bran demonstrated that this test is appropriate for the comparison of solid feedstuffs and suspended organic waste streams. This test method is expected to be suitable for organic waste studies using other sediment dwelling invertebrates.

Effects of feeding and organism loading rate on PCB accumulation by Lumbriculus variegatus in sediment bioaccumulation testing

Science.gov (United States)

Sediment bioaccumulation test methods published by USEPA and ASTM in 2000 specify that the Lumbriculus variegatus, a freshwater oligochaete, should not be fed during the 28-day exposure and recommends an organism loading rate of total organic carbon in sediment to organism dry we...

Enhancement of the surface methane hydrate-bearing layer based on the specific microorganisms form deep seabed sediment in Japan Sea.

Science.gov (United States)

Hata, T.; Yoneda, J.; Yamamoto, K.

2017-12-01

A methane hydrate-bearing layer located near the Japan Sea has been investigated as a new potential energy resource. In this study examined the feasibility of the seabed surface sediment strength located in the Japan Sea improvement technologies for enhancing microbial induced carbonate precipitation (MICP) process. First, the authors cultivated the specific urease production bacterium culture medium from this surface methane hydrate-bearing layer in the seabed (-600m depth) of Japan Sea. After that, two types of the laboratory test (consolidated-drained triaxial tests) were conducted using this specific culture medium from the seabed in the Japan Sea near the Toyama Prefecture and high urease activities bacterium named Bacillus pasteurii. The main outcomes of this research are as follows. 1) Specific culture medium focused on the urease production bacterium can enhancement of the urease activities from the methane hydrate-bearing layer near the Japan Sea side, 2) This specific culture medium can be enhancement of the surface layer strength, 3) The microbial induced carbonate precipitation process can increase the particle size compared to that of the original particles coating the calcite layer surface, 4) The mechanism for increasing the soil strength is based on the addition of cohesion like a cement stabilized soil.

Laboratory evaluation of the Sequoia Scientific LISST-ABS acoustic backscatter sediment sensor

Science.gov (United States)

Snazelle, Teri T.

2017-12-18

Sequoia Scientific’s LISST-ABS is an acoustic backscatter sensor designed to measure suspended-sediment concentration at a point source. Three LISST-ABS were evaluated at the U.S. Geological Survey (USGS) Hydrologic Instrumentation Facility (HIF). Serial numbers 6010, 6039, and 6058 were assessed for accuracy in solutions with varying particle-size distributions and for the effect of temperature on sensor accuracy. Certified sediment samples composed of different ranges of particle size were purchased from Powder Technology Inc. These sediment samples were 30–80-micron (µm) Arizona Test Dust; less than 22-µm ISO 12103-1, A1 Ultrafine Test Dust; and 149-µm MIL-STD 810E Silica Dust. The sensor was able to accurately measure suspended-sediment concentration when calibrated with sediment of the same particle-size distribution as the measured. Overall testing demonstrated that sensors calibrated with finer sized sediments overdetect sediment concentrations with coarser sized sediments, and sensors calibrated with coarser sized sediments do not detect increases in sediment concentrations from small and fine sediments. These test results are not unexpected for an acoustic-backscatter device and stress the need for using accurate site-specific particle-size distributions during sensor calibration. When calibrated for ultrafine dust with a less than 22-µm particle size (silt) and with the Arizona Test Dust with a 30–80-µm range, the data from sensor 6039 were biased high when fractions of the coarser (149-µm) Silica Dust were added. Data from sensor 6058 showed similar results with an elevated response to coarser material when calibrated with a finer particle-size distribution and a lack of detection when subjected to finer particle-size sediment. Sensor 6010 was also tested for the effect of dissimilar particle size during the calibration and showed little effect. Subsequent testing revealed problems with this sensor, including an inadequate temperature

Optimizing sample pretreatment for compound-specific stable carbon isotopic analysis of amino sugars in marine sediment

Science.gov (United States)

Zhu, R.; Lin, Y.-S.; Lipp, J. S.; Meador, T. B.; Hinrichs, K.-U.

2014-09-01

Amino sugars are quantitatively significant constituents of soil and marine sediment, but their sources and turnover in environmental samples remain poorly understood. The stable carbon isotopic composition of amino sugars can provide information on the lifestyles of their source organisms and can be monitored during incubations with labeled substrates to estimate the turnover rates of microbial populations. However, until now, such investigation has been carried out only with soil samples, partly because of the much lower abundance of amino sugars in marine environments. We therefore optimized a procedure for compound-specific isotopic analysis of amino sugars in marine sediment, employing gas chromatography-isotope ratio mass spectrometry. The whole procedure consisted of hydrolysis, neutralization, enrichment, and derivatization of amino sugars. Except for the derivatization step, the protocol introduced negligible isotopic fractionation, and the minimum requirement of amino sugar for isotopic analysis was 20 ng, i.e., equivalent to ~8 ng of amino sugar carbon. Compound-specific stable carbon isotopic analysis of amino sugars obtained from marine sediment extracts indicated that glucosamine and galactosamine were mainly derived from organic detritus, whereas muramic acid showed isotopic imprints from indigenous bacterial activities. The δ13C analysis of amino sugars provides a valuable addition to the biomarker-based characterization of microbial metabolism in the deep marine biosphere, which so far has been lipid oriented and biased towards the detection of archaeal signals.

Agar Sediment Test for Assessing the Suitability of Organic Waste Streams for Recovering Nutrients by the Aquatic Worm Lumbriculus variegatus

NARCIS (Netherlands)

Laarhoven, Bob; Elissen, H.J.H.; Temmink, H.; Buisman, C.J.N.

2016-01-01

An agar sediment test was developed to evaluate the suitability of organic waste streams from the food industry for recovering nutrients by the aquatic worm Lumbriculus variegatus (Lv). The effects of agar gel, sand, and food quantities in the sediment test on worm growth, reproduction, and water

Results of toxicity tests and chemical analyses conducted on sediments collected from the TNX Outfall Delta Operable Unit, July 1999

International Nuclear Information System (INIS)

Specht, W.L.

2000-01-01

In order to provide unit specific toxicity data that will be used to address critical uncertainty in the ecological risk assessment (ERA) for the TNX Outfall Delta Operable Unit (TNXOD OU), sediments were collected from eight locations in the Inner Swamp portion of the operable unit and two unit specific background locations. These samples were analyzed for total mercury, total uranium, and sediment toxicity

Laboratory leach tests of phosphate/sulfate waste grout and leachate adsorption tests using Hanford sediment

Energy Technology Data Exchange (ETDEWEB)

Serne, R.J.; Martin, W.J.; McLaurine, S.B.; Airhart, S.P.; LeGore, V.L.; Treat, R.L.

1987-12-01

An assessment of the long-term risks posed by grout disposal at Hanford requires data on the ability of grout to resist leaching of waste species contained in the grout via contact with water that percolates through the ground. Additionally, data are needed on the ability of Hanford sediment (soil) surrounding the grout and concrete vault to retard migration of any wastes released from the grout. This report describes specific laboratory experiments that are producing empirical leach rate data and leachate-sediment adsorption data for Phosphate-Sulfate Waste (PSW) grout. The leach rate and adsorption values serve as inputs to computer codes used to forecast potential risk resulting from the use of ground water containing leached species. In addition, the report discusses other chemical analyses and geochemical computer code calculations that were used to identify mechanisms that control leach rates and adsorption potential. Knowledge of the controlling chemical and physical processes provides technical defensibility for using the empirical laboratory data to extrapolate the performance of the actual grout disposal system to the long time periods of interest. 59 refs., 83 figs., 18 tabs.

Laboratory leach tests of phosphate/sulfate waste grout and leachate adsorption tests using Hanford sediment

International Nuclear Information System (INIS)

Serne, R.J.; Martin, W.J.; McLaurine, S.B.; Airhart, S.P.; LeGore, V.L.; Treat, R.L.

1987-12-01

An assessment of the long-term risks posed by grout disposal at Hanford requires data on the ability of grout to resist leaching of waste species contained in the grout via contact with water that percolates through the ground. Additionally, data are needed on the ability of Hanford sediment (soil) surrounding the grout and concrete vault to retard migration of any wastes released from the grout. This report describes specific laboratory experiments that are producing empirical leach rate data and leachate-sediment adsorption data for Phosphate-Sulfate Waste (PSW) grout. The leach rate and adsorption values serve as inputs to computer codes used to forecast potential risk resulting from the use of ground water containing leached species. In addition, the report discusses other chemical analyses and geochemical computer code calculations that were used to identify mechanisms that control leach rates and adsorption potential. Knowledge of the controlling chemical and physical processes provides technical defensibility for using the empirical laboratory data to extrapolate the performance of the actual grout disposal system to the long time periods of interest. 59 refs., 83 figs., 18 tabs

Marine dredged sediments as new materials resource for road construction.

Science.gov (United States)

Siham, Kamali; Fabrice, Bernard; Edine, Abriak Nor; Patrick, Degrugilliers

2008-01-01

Large volumes of sediments are dredged each year in Europe in order to maintain harbour activities. With the new European Union directives, harbour managers are encouraged to find environmentally sound solutions for these materials. This paper investigates the potential uses of Dunkirk marine dredged sediment as a new material resource for road building. The mineralogical composition of sediments is evaluated using X-ray diffraction and microscopy analysis. Since sediments contain a high amount of water, a dewatering treatment has been used. Different suitable mixtures, checking specific geotechnical criteria as required in French standards, are identified. The mixtures are then optimized for an economical reuse. The mechanical tests conducted on these mixtures are compaction, bearing capacity, compression and tensile tests. The experimental results show the feasibility of the beneficial use of Dunkirk marine dredged sand and sediments as a new material for the construction of foundation and base layers for roads. Further research is now needed to prove the resistance of this new material to various environmental impacts (e.g., frost damage).

Studying the effect of CO2-induced acidification on sediment toxicity using acute amphipod toxicity test.

Science.gov (United States)

Basallote, M Dolores; De Orte, Manoela R; DelValls, T Ángel; Riba, Inmaculada

2014-01-01

Carbon capture and storage is increasingly being considered one of the most efficient approaches to mitigate the increase of CO2 in the atmosphere associated with anthropogenic emissions. However, the environmental effects of potential CO2 leaks remain largely unknown. The amphipod Ampelisca brevicornis was exposed to environmental sediments collected in different areas of the Gulf of Cádiz and subjected to several pH treatments to study the effects of CO2-induced acidification on sediment toxicity. After 10 days of exposure, the results obtained indicated that high lethal effects were associated with the lowest pH treatments, except for the Ría of Huelva sediment test. The mobility of metals from sediment to the overlying seawater was correlated to a pH decrease. The data obtained revealed that CO2-related acidification would lead to lethal effects on amphipods as well as the mobility of metals, which could increase sediment toxicity.

Terrestrial Sediments of the Earth: Development of a Global Unconsolidated Sediments Map Database (GUM)

Science.gov (United States)

Börker, J.; Hartmann, J.; Amann, T.; Romero-Mujalli, G.

2018-04-01

Mapped unconsolidated sediments cover half of the global land surface. They are of considerable importance for many Earth surface processes like weathering, hydrological fluxes or biogeochemical cycles. Ignoring their characteristics or spatial extent may lead to misinterpretations in Earth System studies. Therefore, a new Global Unconsolidated Sediments Map database (GUM) was compiled, using regional maps specifically representing unconsolidated and quaternary sediments. The new GUM database provides insights into the regional distribution of unconsolidated sediments and their properties. The GUM comprises 911,551 polygons and describes not only sediment types and subtypes, but also parameters like grain size, mineralogy, age and thickness where available. Previous global lithological maps or databases lacked detail for reported unconsolidated sediment areas or missed large areas, and reported a global coverage of 25 to 30%, considering the ice-free land area. Here, alluvial sediments cover about 23% of the mapped total ice-free area, followed by aeolian sediments (˜21%), glacial sediments (˜20%), and colluvial sediments (˜16%). A specific focus during the creation of the database was on the distribution of loess deposits, since loess is highly reactive and relevant to understand geochemical cycles related to dust deposition and weathering processes. An additional layer compiling pyroclastic sediment is added, which merges consolidated and unconsolidated pyroclastic sediments. The compilation shows latitudinal abundances of sediment types related to climate of the past. The GUM database is available at the PANGAEA database (https://doi.org/10.1594/PANGAEA.884822).

Effects of sediment quality on macroinvertebrates in the Sunraysia region of the Murray-Darling Rivers, Australia

Energy Technology Data Exchange (ETDEWEB)

Sharley, David J. [Centre for Environmental Stress and Adaptation Research-Hoffmann Laboratory, Zoology Department, University of Melbourne, Level 2, Bio 21 Institute, 30 Flemington Road, Parkville, Victoria 3010 (Australia)], E-mail: sharleyd@unimelb.edu.au; Hoffmann, Ary A. [Centre for Environmental Stress and Adaptation Research-Hoffmann Laboratory, Zoology Department, University of Melbourne, Level 2, Bio 21 Institute, 30 Flemington Road, Parkville, Victoria 3010 (Australia); Pettigrove, Vincent [Research and Technology, Melbourne Water, PO Box 4342, Melbourne, Victoria 3001 (Australia)

2008-12-15

A field-based microcosm approach was tested to identify deterioration of sediment quality in waterways using freshwater macroinvertebrates. The method can potentially identify the nature of contaminants based on species-specific responses. Sediments were collected from the Murray and Darling Rivers and irrigation drains within the Sunraysia region of south-eastern Australia and compared to non-polluted reference sediment. Clean sediments were also spiked with fertiliser to test whether nutrients affected the aquatic fauna. Seven of the eight sediments from the Sunraysia region had a negative impact on the macroinvertebrates, in particular sediment from the Darling River, which supported an impoverished fauna. Three species of chironomid showed varied responses to sediment quality and, although it was hypothesised that nutrients may have impacted on the macroinvertebrate fauna, the results suggest that other pollutants are also involved. The field-based microcosm method proved effective for determining the impact of sediment quality on indigenous macroinvertebrates. - Sediment quality effects on freshwater macroinvertebrates are isolated.

Effects of sediment quality on macroinvertebrates in the Sunraysia region of the Murray-Darling Rivers, Australia

International Nuclear Information System (INIS)

Sharley, David J.; Hoffmann, Ary A.; Pettigrove, Vincent

2008-01-01

A field-based microcosm approach was tested to identify deterioration of sediment quality in waterways using freshwater macroinvertebrates. The method can potentially identify the nature of contaminants based on species-specific responses. Sediments were collected from the Murray and Darling Rivers and irrigation drains within the Sunraysia region of south-eastern Australia and compared to non-polluted reference sediment. Clean sediments were also spiked with fertiliser to test whether nutrients affected the aquatic fauna. Seven of the eight sediments from the Sunraysia region had a negative impact on the macroinvertebrates, in particular sediment from the Darling River, which supported an impoverished fauna. Three species of chironomid showed varied responses to sediment quality and, although it was hypothesised that nutrients may have impacted on the macroinvertebrate fauna, the results suggest that other pollutants are also involved. The field-based microcosm method proved effective for determining the impact of sediment quality on indigenous macroinvertebrates. - Sediment quality effects on freshwater macroinvertebrates are isolated

Genotoxic and teratogenic potential of marine sediment extracts investigated with comet assay and zebrafish test

International Nuclear Information System (INIS)

Kammann, Ulrike; Biselli, Scarlett; Huehnerfuss, Heinrich; Reineke, Ninja; Theobald, Norbert; Vobach, Michael; Wosniok, Werner

2004-01-01

Organic extracts of marine sediments from the North Sea and the Baltic Sea were investigated with two toxicity assays. The comet assay based on the fish cell line Epithelioma papulosum cyprini (EPC) was applied to determine the genotoxic potential; zebrafish embryos (Danio rerio) were used to quantify the teratogenic potential of the samples. EC 50 values were calculated from dose-response curves for both test systems. Highest teratogenic and genotoxic effects normalised to total organic carbon (TOC) content were detected in sediment samples of different origins. Polychlorinated biphenyls (PCBs) and polycyclic aromatic hydrocarbons (PAHs) are not likely to be the causes of the observed effects, as demonstrated by a two-step fractionation procedure of selected extracts. The toxic potential was more pronounced in fractions having polarity higher than those possessed by PAHs and PCBs. The suitability of the two in vitro test systems for assessing genotoxic and teratogenic effects of marine sediment extracts could be demonstrated. - Capsule: In vitro toxicity assays are used to assess genotoxic and teratogenic effects of environmental extracts

Testing of Badminton-Specific Endurance.

Science.gov (United States)

Madsen, Christian M; Højlyng, Mads; Nybo, Lars

2016-09-01

Madsen, CM, Højlyng, M, and Nybo, L. Testing of badminton-specific endurance. J Strength Cond Res 30(9): 2582-2590, 2016-In the present study, a novel intermittent badminton endurance (B-ENDURANCE) test was developed and tested in elite (n = 17) and skilled (n = 9) badminton players and in age-matched physically active men (nonbadminton players; n = 8). In addition, B-ENDURANCE test-retest reproducibility was evaluated in 9 badminton players. The B-ENDURANCE test is an incremental test where each level consists of repeated sequences of badminton-specific actions toward the 4 corners of the court. The subject starts in the center of the court in front of a computer screen and within each sequence, he must, in a randomized order, complete 8 actions as dictated by the computer, providing the audiovisual input and verifying that the appropriate sensor is activated within the allocated time. Recovery time between each sequence is 10 seconds throughout the test, but the time to complete each sequence is gradually decreased until the subjects cannot follow the dictated tempo. The B-ENDURANCE test performance for elite players was better (p ≤ 0.05) compared with the skilled players and nonbadminton players. In addition, the B-ENDURANCE test performance correlated (r = 0.8 and p badminton-specific endurance but at least 1 familiarization trial is recommended if the test is used for evaluation of longitudinal changes, e.g., tracking training effects.

Integrating the fish embryo toxicity test as triad element for sediment toxicity assessment based on the water framework directive approach

Energy Technology Data Exchange (ETDEWEB)

Bartzke, Mariana [Dept. Aquatic Ecotoxicology, Goethe Univ. Frankfurt am Main (Germany); Gobio GmbH, Aarbergen/Kettenbach (Germany); Dept. Bioanalytical Ecotoxicology, Helmholtz Centre for Environmental Research, UFZ, Leipzig (Germany); Delov, Vera [Dept. Aquatic Ecotoxicology, Goethe Univ. Frankfurt am Main (Germany); Gobio GmbH, Aarbergen/Kettenbach (Germany); Ecotoxicology, Fraunhofer Inst. for Molecular Biology and Applied Ecology IME, Aachen (Germany); Stahlschmidt-Allner, Petra; Allner, Bernhard [Gobio GmbH, Aarbergen/Kettenbach (Germany); Oehlmann, Joerg [Dept. Aquatic Ecotoxicology, Goethe Univ. Frankfurt am Main (Germany)

2010-04-15

Purpose: The objective of this study was to complement analyses according to the European Union Water Framework Directive (WFD) with a sediment toxicity analysis as part of an integrated river assessment. To this end, Hessian water courses were analyzed using the sediment quality triad concept according to Chapman with chemical analyses, in situ effect evaluations, and ecotoxicological assessments. For the ecotoxicological assessment (fish embryo toxicity test with Danio rerio), a new evaluation scheme was developed, the fish teratogenicity index (FTI), that allows for a classification of sediments into ecological quality classes compliant to the WFD. Materials and methods sediment and macrozoobenthos samples were taken from tributaries of the rivers Fulda and Lahn. Sediments were characterized regarding particle size, carbon, heavy metals, and polyaromatic hydrocarbon content. Macroinvertebrate samples were taken via multi-habitat sampling. The fish embryo toxicity test with D. rerio was conducted as a contact assay on the basis of DIN 38415-6. Results and discussion The integrated assessment indicated a significant influence of heavy metals and carbon content on macroinvertebrate communities. The bioaccessibility of sediment pollutants were clearly demonstrated by the FTI, which showed a wide range of adverse effects. A significant linear relationship between metals and the FTI was detected. However, there was no statistically significant evidence that macroinvertebrate communities were affected by the hydromorphological quality clements at the sampling sites. Conclusions The new scheme for the assessment of fish embryo toxicity test was successfully applied. The results suggest that sediment compounds impact macroinvertebrate communities and early development of fish. It demonstrates that the quality of sediments should be evaluated on a routine basis as part of an integrated river assessment. (orig.)

Ecotoxicological risk assessment linked to infilling quarries with treated dredged seaport sediments

Energy Technology Data Exchange (ETDEWEB)

Perrodin, Yves, E-mail: perrodin@entpe.fr [Universite de Lyon, ENTPE, CNRS, UMR 5023 LEHNA, 2 rue Maurice Audin, 69518 Vaulx-en-Velin (France); Donguy, Gilles [Universite de Lyon, ENTPE, CNRS, UMR 5023 LEHNA, 2 rue Maurice Audin, 69518 Vaulx-en-Velin (France); Bazin, Christine [INSAVALOR, 20 avenue Albert Einstein, 69621 Villeurbanne Cedex (France); Volatier, Laurence; Durrieu, Claude [Universite de Lyon, ENTPE, CNRS, UMR 5023 LEHNA, 2 rue Maurice Audin, 69518 Vaulx-en-Velin (France); Bony, Sylvie; Devaux, Alain [Universite de Lyon, ENTPE, CNRS, UMR 5023 LEHNA, 2 rue Maurice Audin, 69518 Vaulx-en-Velin (France); INRA, USC IGH, UMR LEHNA, 2, rue Maurice Audin, 69518 Vaulx-en-Velin (France); Abdelghafour, Mohammed; Moretto, Robert [INSAVALOR, 20 avenue Albert Einstein, 69621 Villeurbanne Cedex (France)

2012-08-01

The dredged sediments of polluted seaports now raise complex management problems since it is no longer possible to discharge them into the sea. This results in the need to manage them on land, raising other types of technical, economic and environmental problems. Regarding the technical and economic dimensions, traditional waste treatment methods have proved to be poorly adapted, due to very high costs and low absorbable volumes. In this context, filling quarries in coastal areas with treated sediments could represent an interesting alternative for these materials. Nevertheless, for the environmental dimension, it is necessary to demonstrate that this possibility is harmless to inland ecosystems. Consequently, a specific ecotoxicological risk assessment methodology has been formulated and tested on three sediments taken from seaboards of France, in view to providing an operational and usable tool for the prior validation of any operation to fill quarries with treated seaport sediments. This method incorporates the formulation of a global conceptual model of the scenario studied and the definition of protocols for each of its steps: the characterisation of exposures (based on a simulation of sediment deposit), the characterisation of effects (via the study of sediments ecotoxicity), and the final ecotoxicological risk assessment performed as a calculation of a risk quotient. It includes the implementation in parallel of two types of complementary approach: the 'substances' approach derived from the European methodology for assessing new substances placed on the market, and the 'matrix' approach which is similar to methods developed in France to assess ecological risks in other domains (waste management, polluted site management, Horizontal-Ellipsis ). The application of this dual approach to the three sediments tested led to conclude with reliability that the project to deposit sediments '1' and '2' presented a low risk for

Ecotoxicological risk assessment linked to infilling quarries with treated dredged seaport sediments

International Nuclear Information System (INIS)

Perrodin, Yves; Donguy, Gilles; Bazin, Christine; Volatier, Laurence; Durrieu, Claude; Bony, Sylvie; Devaux, Alain; Abdelghafour, Mohammed; Moretto, Robert

2012-01-01

The dredged sediments of polluted seaports now raise complex management problems since it is no longer possible to discharge them into the sea. This results in the need to manage them on land, raising other types of technical, economic and environmental problems. Regarding the technical and economic dimensions, traditional waste treatment methods have proved to be poorly adapted, due to very high costs and low absorbable volumes. In this context, filling quarries in coastal areas with treated sediments could represent an interesting alternative for these materials. Nevertheless, for the environmental dimension, it is necessary to demonstrate that this possibility is harmless to inland ecosystems. Consequently, a specific ecotoxicological risk assessment methodology has been formulated and tested on three sediments taken from seaboards of France, in view to providing an operational and usable tool for the prior validation of any operation to fill quarries with treated seaport sediments. This method incorporates the formulation of a global conceptual model of the scenario studied and the definition of protocols for each of its steps: the characterisation of exposures (based on a simulation of sediment deposit), the characterisation of effects (via the study of sediments ecotoxicity), and the final ecotoxicological risk assessment performed as a calculation of a risk quotient. It includes the implementation in parallel of two types of complementary approach: the “substances” approach derived from the European methodology for assessing new substances placed on the market, and the “matrix” approach which is similar to methods developed in France to assess ecological risks in other domains (waste management, polluted site management, …). The application of this dual approach to the three sediments tested led to conclude with reliability that the project to deposit sediments “1” and “2” presented a low risk for the peripheral aquatic ecosystems while

Kato-Katz and Lumbreras rapid sedimentation test to evaluate helminth prevalence in the setting of a school-based deworming program

OpenAIRE

Lopez, Martha; Morales, Maria Luisa; Konana, Monisha; Hoyer, Paige; Pineda-Reyes, Roberto; White, Arthur Clinton; Garcia, Hector Hugo; Lescano, Andres Guillermo; Gotuzzo, Eduardo; Cabada, Miguel Mauricio

2016-01-01

The sensitivity of the Kato-Katz test is suboptimal for the evaluation of intestinal helminth prevalence. Moreover, during mass deworming, as helminth egg burden decreases, the sensitivity is likely to decrease. The Lumbreras rapid sedimentation (Lumbreras) is a low-cost non-quantitative test, but may provide useful information in low burden areas. We compared the prevalence of intestinal helminth infections assessed by the Kato-Katz and the Lumbreras rapid sedimentation test on 3 stool speci...

Health risk assessment linked to filling coastal quarries with treated dredged seaport sediments.

Science.gov (United States)

Perrodin, Yves; Donguy, Gilles; Emmanuel, Evens; Winiarski, Thierry

2014-07-01

Dredged seaport sediments raise complex management problems since it is no longer possible to discharge them into the sea. Traditional waste treatments are poorly adapted for these materials in terms of absorbable volumes and cost. In this context, filling quarries with treated sediments appears interesting but its safety regarding human health must be demonstrated. To achieve this, a specific methodology for assessing health risks has been developed and tested on three seaport sediments. This methodology includes the development of a conceptual model of the global scenario studied and the definition of specific protocols for each of its major steps. The approach proposed includes in particular the use of metrological and experimental tools that are new in this context: (i) an experimental lysimeter for characterizing the deposit emissions, and (ii) a geological radar for identifying potential preferential pathways between the sediment deposit and the groundwater. The application of this approach on the three sediments tested for the scenario studied showed the absence of health risk associated with the consumption of groundwater for substances having a "threshold effect" (risk quotient risk for substances having a "non-threshold effect", with the notable exception of arsenic (individual risk equal to 3.10(-6)). Copyright © 2014 Elsevier B.V. All rights reserved.

Testing and Validation Studies of the NSMII-Benthic Sediment Diagenesis Module

Science.gov (United States)

2016-07-01

plug in” water quality modules for HEC-RAS (Hydrologic Engineering Center- River Analysis System) and other hydrologic and hydraulic models. The...hydrologic and hydraulic models (Zhang and Johnson 2016). The NSMs are designed to be inde- pendent of the dimensionality of the spatial domain; they...fied in the above tests were reduced by 20%, 50%, and 90%, respectively. Model predictions for SOD and sediment release of NH4, NO3, H2S, CH4

A SEDIMENT TOXICITY METHOD USING LEMNA MINOR, DUCKWEED

Science.gov (United States)

We developed a Lemna minor sediment toxicity test method to assess sediment contaminants which may affect plants. This 96-hour test used 15 ml of sediment and 2 ml of overlying water which was renewed after 48 hours. Sand was used as the control sediment and also to dilute test ...

Predicted effectiveness of in-situ activated carbon amendment for field sediment sites with variable site- and compound-specific characteristics

Energy Technology Data Exchange (ETDEWEB)

Choi, Yongju, E-mail: ychoi81@snu.ac.kr [Department of Civil and Environmental Engineering, Seoul National University, Seoul 151-744 (Korea, Republic of); Cho, Yeo-Myoung; Luthy, Richard G. [Department of Civil and Environmental Engineering, Stanford University, Stanford, CA 94305-4020 (United States); Werner, David [School of Civil Engineering and Geosciences, Newcastle University, Newcastle upon Tyne NE1 7RU (United Kingdom)

2016-01-15

Highlights: • The model accounts for the heterogeneity of AC distribution in field applications. • AC amendment effectiveness is predicted for ten sediment sites. • An HOC mass transfer model and calibrated parameters provide reliable predictions. • AC amendment is predicted to be effective for most sites. • K{sub ow}, K{sub d}, and equilibrium-based calculations are useful indicators. - Abstract: A growing body of evidence shows that the effectiveness of in-situ activated carbon (AC) amendment to treat hydrophobic organic contaminants (HOCs) in sediments can be reliably predicted using a mass transfer modeling approach. This study analyzes available field data for characterizing AC-sediment distribution after mechanical mixing of AC into sediment. Those distributions are used to develop an HOC mass transfer model that accounts for plausible heterogeneities resulting from mixing of AC into sediment. The model is applied to ten field sites in the U.S. and Europe with 2–3 representative HOCs from each site using site- and HOC-specific model parameters collected from the literature. The model predicts that the AC amendment reduces the pore-water HOC concentrations by more than 95% fifteen years after AC deployment for 18 of the 25 total simulated cases when the AC is applied at doses of 1.5 times sediment total organic carbon content with an upper limit of 5 dry wt%. The predicted effectiveness shows negative correlation with the HOC octanol–water partitioning coefficients and the sediment-water distribution coefficients, and positive correlation with the effectiveness calculated based on equilibrium coefficients of sediment and AC, suggesting the possibility for use of the values for screening-level assessments.

Predicted effectiveness of in-situ activated carbon amendment for field sediment sites with variable site- and compound-specific characteristics

International Nuclear Information System (INIS)

Choi, Yongju; Cho, Yeo-Myoung; Luthy, Richard G.; Werner, David

2016-01-01

Highlights: • The model accounts for the heterogeneity of AC distribution in field applications. • AC amendment effectiveness is predicted for ten sediment sites. • An HOC mass transfer model and calibrated parameters provide reliable predictions. • AC amendment is predicted to be effective for most sites. • K ow , K d , and equilibrium-based calculations are useful indicators. - Abstract: A growing body of evidence shows that the effectiveness of in-situ activated carbon (AC) amendment to treat hydrophobic organic contaminants (HOCs) in sediments can be reliably predicted using a mass transfer modeling approach. This study analyzes available field data for characterizing AC-sediment distribution after mechanical mixing of AC into sediment. Those distributions are used to develop an HOC mass transfer model that accounts for plausible heterogeneities resulting from mixing of AC into sediment. The model is applied to ten field sites in the U.S. and Europe with 2–3 representative HOCs from each site using site- and HOC-specific model parameters collected from the literature. The model predicts that the AC amendment reduces the pore-water HOC concentrations by more than 95% fifteen years after AC deployment for 18 of the 25 total simulated cases when the AC is applied at doses of 1.5 times sediment total organic carbon content with an upper limit of 5 dry wt%. The predicted effectiveness shows negative correlation with the HOC octanol–water partitioning coefficients and the sediment-water distribution coefficients, and positive correlation with the effectiveness calculated based on equilibrium coefficients of sediment and AC, suggesting the possibility for use of the values for screening-level assessments.

Prospective Environmental Risk Assessment for Sediment-Bound Organic Chemicals: A Proposal for Tiered Effect Assessment.

Science.gov (United States)

Diepens, Noël J; Koelmans, Albert A; Baveco, Hans; van den Brink, Paul J; van den Heuvel-Greve, Martine J; Brock, Theo C M

A broadly accepted framework for prospective environmental risk assessment (ERA) of sediment-bound organic chemicals is currently lacking. Such a framework requires clear protection goals, evidence-based concepts that link exposure to effects and a transparent tiered-effect assessment. In this paper, we provide a tiered prospective sediment ERA procedure for organic chemicals in sediment, with a focus on the applicable European regulations and the underlying data requirements. Using the ecosystem services concept, we derived specific protection goals for ecosystem service providing units: microorganisms, benthic algae, sediment-rooted macrophytes, benthic invertebrates and benthic vertebrates. Triggers for sediment toxicity testing are discussed.We recommend a tiered approach (Tier 0 through Tier 3). Tier-0 is a cost-effective screening based on chronic water-exposure toxicity data for pelagic species and equilibrium partitioning. Tier-1 is based on spiked sediment laboratory toxicity tests with standard benthic test species and standardised test methods. If comparable chronic toxicity data for both standard and additional benthic test species are available, the Species Sensitivity Distribution (SSD) approach is a more viable Tier-2 option than the geometric mean approach. This paper includes criteria for accepting results of sediment-spiked single species toxicity tests in prospective ERA, and for the application of the SSD approach. We propose micro/mesocosm experiments with spiked sediment, to study colonisation success by benthic organisms, as a Tier-3 option. Ecological effect models can be used to supplement the experimental tiers. A strategy for unifying information from various tiers by experimental work and exposure-and effect modelling is provided.

Congener-specific distribution and bioaccumulation of short-chain chlorinated paraffins in sediments and bivalves of the Bohai Sea, China.

Science.gov (United States)

Ma, Xindong; Chen, Chen; Zhang, Haijun; Gao, Yuan; Wang, Zhen; Yao, Ziwei; Chen, Jiping; Chen, Jingwen

2014-02-15

Short-chain chlorinated paraffins (SCCPs) are a new type of persistent organic pollutants that are of great environmental concern because of their wide distribution. In this study, surface sediments and bivalve samples were collected from the coastal area of the Bohai Sea in China. Total SCCP (ΣSCCP) concentrations in surface sediments and bivalves ranged from 97.4 ng g(-1) dry weight (dw) to 1756.7 ng g(-1) dw and 476.4-3269.5 ng g(-1) dw, respectively. C10-CPs and C11-CPs were the predominant homologue groups in all sediments and bivalves. Specific congener composition analysis and correspondence analysis indicated that the local SCCP source mainly came from CP-42 and CP-52 products, and riverine input had an important function. The biota-sediment accumulation factors of ΣSCCPs for bivalves ranged from 1.08 to 1.61, and a significant correlation indicated that the SCCP congener with higher chlorination degree was more likely to be accumulated in bivalves. Copyright © 2014. Published by Elsevier Ltd.

Prostate-Specific Antigen (PSA) Test

Science.gov (United States)

... Cancer Prostate Cancer Screening Research Prostate-Specific Antigen (PSA) Test On This Page What is the PSA ... parts of the body before being detected. The PSA test may give false-positive or false-negative ...

Documentation of tests on particle size methodologies for laser diffraction compared to traditional sieving and sedimentation analysis

DEFF Research Database (Denmark)

Rasmussen, Charlotte; Dalsgaard, Kristian

Sieving and sedimentation analyses by pipette or hydrometer are historically the traditional methods for determining particle size distributions (PSD). A more informative and faster alternative has for years been laser diffraction (LD). From 2003 to 2013 the authors of this paper have worked...... intensively with PSD and performed various tests and investigations, using LD, sedimentation (by pipette) and sieving. The aim was to improve and understand the relationship between these various techniques, pre-treatment effects and preferably find a unifying correlation factor. As a result, method...... comparisons of LD and sieving/sedimentation are difficult, as LD is a 3D optical volume measurement, sieving is a 2D width measurement, and sedimentation is density dependent. Platy particles like clay are generally measured to be coarser than traditional methods when LD is used. For LD the clay...

Sediment Transport

DEFF Research Database (Denmark)

Liu, Zhou

Flow and sediment transport are important in relation to several engineering topics, e.g. erosion around structures, backfilling of dredged channels and nearshore morphological change. The purpose of the present book is to describe both the basic hydrodynamics and the basic sediment transport...... mechanics. Chapter 1 deals with fundamentals in fluid mechanics with emphasis on bed shear stress by currents, while chapter 3 discusses wave boundary layer theory. They are both written with a view to sediment transport. Sediment transport in rivers, cross-shore and longshore are dealt with in chapters 2......, 4 and 5, respectively. It is not the intention of the book to give a broad review of the literature on this very wide topic. The book tries to pick up information which is of engineering importance. An obstacle to the study of sedimentation is the scale effect in model tests. Whenever small...

Matrix-specific distribution and diastereomeric profiles of hexabromocyclododecane (HBCD) in a multimedia environment: Air, soil, sludge, sediment, and fish.

Science.gov (United States)

Jo, Hyeyeong; Son, Min-Hui; Seo, Sung-Hee; Chang, Yoon-Seok

2017-07-01

Hexabromocyclododecane (HBCD) contamination and its diastereomeric profile were investigated in a multi-media environment along a river at the local scale in air, soil, sludge, sediment, and fish samples. The spatial distribution of HBCD in each matrix showed a different result. The highest concentrations of HBCD in air and soil were detected near a general industrial complex; in the sediment and sludge samples, they were detected in the down-stream region (i.e., urban area). Each matrix showed the specific distribution patterns of HBCD diastereomers, suggesting continuous inputs of contaminants, different physicochemical properties, or isomerizations. The particle phases in air, sludge, and fish matrices were dominated by α-HBCD, owing to HBCD's various isomerization processes and different degradation rate in the environment, and metabolic capabilities of the fish; in contrast, the sediment and soil matrices were dominated by γ-HBCD because of the major composition of the technical mixtures and the strong adsorption onto solid particles. Based on these results, the prevalent and matrix-specific distribution of HBCD diastereomers suggested that more careful consideration should be given to the characteristics of the matrices and their effects on the potential influence of HBCD at the diastereomeric level. Copyright © 2017 Elsevier Ltd. All rights reserved.

A novel method for sampling the suspended sediment load in the tidal environment using bi-directional time-integrated mass-flux sediment (TIMS) samplers

Science.gov (United States)

Elliott, Emily A.; Monbureau, Elaine; Walters, Glenn W.; Elliott, Mark A.; McKee, Brent A.; Rodriguez, Antonio B.

2017-12-01

Identifying the source and abundance of sediment transported within tidal creeks is essential for studying the connectivity between coastal watersheds and estuaries. The fine-grained suspended sediment load (SSL) makes up a substantial portion of the total sediment load carried within an estuarine system and efficient sampling of the SSL is critical to our understanding of nutrient and contaminant transport, anthropogenic influence, and the effects of climate. Unfortunately, traditional methods of sampling the SSL, including instantaneous measurements and automatic samplers, can be labor intensive, expensive and often yield insufficient mass for comprehensive geochemical analysis. In estuaries this issue is even more pronounced due to bi-directional tidal flow. This study tests the efficacy of a time-integrated mass sediment sampler (TIMS) design, originally developed for uni-directional flow within the fluvial environment, modified in this work for implementation the tidal environment under bi-directional flow conditions. Our new TIMS design utilizes an 'L' shaped outflow tube to prevent backflow, and when deployed in mirrored pairs, each sampler collects sediment uniquely in one direction of tidal flow. Laboratory flume experiments using dye and particle image velocimetry (PIV) were used to characterize the flow within the sampler, specifically, to quantify the settling velocities and identify stagnation points. Further laboratory tests of sediment indicate that bidirectional TIMS capture up to 96% of incoming SSL across a range of flow velocities (0.3-0.6 m s-1). The modified TIMS design was tested in the field at two distinct sampling locations within the tidal zone. Single-time point suspended sediment samples were collected at high and low tide and compared to time-integrated suspended sediment samples collected by the bi-directional TIMS over the same four-day period. Particle-size composition from the bi-directional TIMS were representative of the array of

What Food and Feeding Rates are Optimum for the Chironomus dilutus Sediment Toxicity Test Method?

Science.gov (United States)

Laboratory tests with benthic macroinvertebrates are commonly used to assess the toxicity of both contaminated sediments and individual chemicals. Among the standard procedures for benthic macroinvertebrates are 10-d, 20-d, and life cycle exposures using the midge, Chironomus ...

Laboratory tests of bentonite stabilization of bottom sediments from a dam reservoir in relation to their usage in municipal solid waste landfill liners

Directory of Open Access Journals (Sweden)

Karolina Koś

2016-09-01

Full Text Available Geotechnical parameters of bottom sediments from a dam reservoir (Rzeszowski Reservoir, Poland with bentonite addition are presented in the paper. Tests were carried out in the aspect of the possible usage of sediments as a material for soil liners in Municipal Solid Waste Landfill. Mentioned sediments did not fulfilled the permeability and plasticity criteria defined for soils that can be used in liners. The bentonite addition caused, among other things, a decrease in permeability coefficient and increase in plasticity index. Based on the carried out tests it was stated that sediments with 6% addition of bentonite fulfil all requirements and can be used for liners in MSWL.

Project NEO Specific Impulse Testing Solutions

Science.gov (United States)

Baffa, Bill

2018-01-01

The Neo test stand is currently configured to fire a horizontally mounted rocket motor with up to 6500 lbf thrust. Currently, the Neo test stand can measure flow of liquid propellant and oxidizer, pressures residing in the closed system up to the combustion chamber. The current configuration does not have the ability to provide all data needed to compute specific impulse. This presents three methods to outfit the NEO test fixture with instrumentation allowing for calculation of specific impulse.

An Exploratory Analysis of Stream Teratogenicity and Human Health Using Zebrafish Whole-Sediment Toxicity Test

Directory of Open Access Journals (Sweden)

Matthew Dellinger

2014-02-01

Full Text Available This study demonstrates a novel application of effect-based toxicity testing for streams that may provide indications of co-perturbation to ecological and human health. For this study, a sediment contact assay using zebrafish (Danio rerio embryos was adapted to serve as an indicator of teratogenic stress within river sediments. Sediment samples were collected from Lake Michigan tributary watersheds. Sediment contact assay responses were then compared to prevalence of congenital heart disease (CHD and vital statistic birth indicators aggregated from civil divisions associated with the watersheds. Significant risk relationships were detected between variation in early life-stage (ELS endpoints of zebrafish embryos 72 h post-fertilization and the birth prevalence of human congenital heart disease, low birthweight and infant mortality. Examination of principal components of ELS endpoints suggests that variance related to embryo heart and circulatory malformations is most closely associated with human CHD prevalence. Though toxicity assays are sometimes used prospectively, this form of investigation can only be conducted retrospectively. These results support the hypothesis that bioassays normally used for ecological screening can be useful as indicators of environmental stress to humans and expand our understanding of environmental–human health linkages.

In-Situ Survival Mechanisms of U and Tc Reducing Bacteria in Contaminated Sediments. Final Report

International Nuclear Information System (INIS)

Lee Krumholz Jimmy Ballard

2005-01-01

The proposed effort will identify genes and ultimately physiological mechanisms and pathways that are expressed under in situ conditions and are critical to functioning of aquifer dwelling anaerobic bacteria living in contaminated systems. The main objectives are: (1) Determine which Metal-reducer specific genes are important for activities in normal and contaminated subsurface sediment. To achieve these goals, we have generated a library of chromosomal mutants. These are introduced into contaminated sediments, incubated, allowed to grow, and then reisolated. A negative selection process allows us to determine which mutants have been selected against in sediments and thereby identify genes required for survival in subsurface sediments. (2) Delineate the function of these genes through GeneBank and Clusters of Orthologous Groups (COGs) comparisons and analyze other sediment microorganisms to determine if similar genes are present in these populations. After determining the sequence of the genes identified through the previous objectives, we delineate the role of those specific genes in the physiology of G20, MR-1 and perhaps other microorganisms. (3) Determine the loss in function of a select group of mutants. Cells with mutations in known genes with testable functions are assayed for the loss of that function if specific assays are available. Mutants with unknown loss of function and other mutants are run through a series of tests including motility, attachment, and rate of sulfate or iron reduction. These tests allow us to categorize mutants for subsequent more detailed study

Prostate-specific antigen testing accuracy in community practice

Directory of Open Access Journals (Sweden)

Adams-Cameron Meg

2002-10-01

Full Text Available Abstract Background Most data on prostate-specific antigen (PSA testing come from urologic cohorts comprised of volunteers for screening programs. We evaluated the diagnostic accuracy of PSA testing for detecting prostate cancer in community practice. Methods PSA testing results were compared with a reference standard of prostate biopsy. Subjects were 2,620 men 40 years and older undergoing (PSA testing and biopsy from 1/1/95 through 12/31/98 in the Albuquerque, New Mexico metropolitan area. Diagnostic measures included the area under the receiver-operating characteristic curve, sensitivity, specificity, and likelihood ratios. Results Cancer was detected in 930 subjects (35%. The area under the ROC curve was 0.67 and the PSA cutpoint of 4 ng/ml had a sensitivity of 86% and a specificity of 33%. The likelihood ratio for a positive test (LR+ was 1.28 and 0.42 for a negative test (LR-. PSA testing was most sensitive (90% but least specific (27% in older men. Age-specific reference ranges improved specificity in older men (49% but decreased sensitivity (70%, with an LR+ of 1.38. Lowering the PSA cutpoint to 2 ng/ml resulted in a sensitivity of 95%, a specificity of 20%, and an LR+ of 1.19. Conclusions PSA testing had fair discriminating power for detecting prostate cancer in community practice. The PSA cutpoint of 4 ng/ml was sensitive but relatively non-specific and associated likelihood ratios only moderately revised probabilities for cancer. Using age-specific reference ranges and a PSA cutpoint below 4 ng/ml improved test specificity and sensitivity, respectively, but did not improve the overall accuracy of PSA testing.

Complete Reductive Dehalogenation of Brominated Biphenyls by Anaerobic Microorganisms in Sediment

Science.gov (United States)

Bedard, Donna L.; Van Dort, Heidi M.

1998-01-01

We sought to determine whether microorganisms from the polychlorinated biphenyl (PCB)-contaminated sediment in Woods Pond (Lenox, Mass.) could dehalogenate brominated biphenyls. The PCB dechlorination specificities for the microorganisms in this sediment have been well characterized. This allowed us to compare the dehalogenation specificities for brominated biphenyls and chlorinated biphenyls within a single sediment. Anaerobic sediment microcosms were incubated separately at 25°C with 16 different mono- to tetrabrominated biphenyls (350 μM) and disodium malate (10 mM). Samples were extracted and analyzed by gas chromatography with an electron capture detector and a mass spectrometer detector at various times for up to 54 weeks. All of the tested brominated biphenyls were dehalogenated. For most congeners, including 2,6-dibromobiphenyl (26-BB) and 24-25-BB, the dehalogenation began within 1 to 2 weeks. However, for 246-BB and 2-2-BB, debromination was first observed at 7 and 14 weeks, respectively. Most intermediate products did not persist, but when 2-2-BB was produced as a dehalogenation product, it persisted for at least 15 weeks before it was dehalogenated to 2-BB and then to biphenyl. The dehalogenation specificities for brominated and chlorinated biphenyls were similar: meta and para substituents were generally removed first, and ortho substituents were more recalcitrant. However, the brominated biphenyls were better dehalogenation substrates than the chlorinated biphenyls. All of the tested bromobiphenyls, including those with ortho and unflanked meta and para substituents, were ultimately dehalogenated to biphenyl, whereas their chlorinated counterparts either were not dehalogenation substrates or were only partially dehalogenated. Our data suggest that PCB-dechlorinating microorganisms may be able to dehalogenate brominated biphenyls and may exhibit a relaxed specificity for these substrates. PMID:16349530

Testing of a uranium downhole logging system to measure in-situ plutonium concentrations in sediments

International Nuclear Information System (INIS)

Kasper, R.B.; Kay, M.A.; Bruns, L.E.; Stokes, J.A.; Steinman, D.K.; Adams, J.

1980-11-01

A prototype urainium borehole logging system, developed for uranium exploration, was modified for Pu assay and testing at the site. It uses the delayed fission neutron (DFN) method. It was tested in a retired Pu facility, the 216-Z-1A Crib. General agreement between laboratory determined Pu concentrations in sediment samples and neutron flux measurements was found for the relative distribution with depth

New Temperature Calibrations and Validation Tests of 5- and 6-Methyl brGDGTs in Lake Sediment

Science.gov (United States)

Russell, J. M.; Williams, J. W.; Jackson, S. T.; S Sinninghe Damsté, J.; Watson, B. I.

2017-12-01

Branched glycerol dialkyl glycerol tetraethers (brGDGTs) are increasingly used to reconstruct changes in temperature and other environmental variables. There are now multiple methods to measure brGDGTs, many different brGDGT calibrations for different environments, and many applications of the brGDGT proxy, yet brGDGT-based temperature reconstructions have rarely been tested against independent paleoclimate data to evaluate and validate the proxy. We present new temperature calibrations of brGDGTs preserved in 65 lake sediment samples determined using new, improved chromatographic methods that separate 5- and 6-methyl brGDGT isomers. We test these new calibrations, as well as calibrations using older methods that do not separate brGDGT isomers, in a sediment core spanning the last deglaciation from a classic North American site (Silver Lake, USA) against independent pollen-derived temperature estimates. The distributions of and environmental controls on 5- and 6-methyl brGDGTs differs significantly in lake sediments versus soils, suggesting different controls on bacterial membrane lipid compositions in the two environments. This results in different calibrations in soils and lake sediments; however, like soils, separation of 5- and 6-methyl isomers significantly improves the errors statistics of some brGDGT-temperature calibrations, with calibration errors of 2-2.5 ºC. Applying these calibrations to sediments from Silver Lake, we observe warming from the last glacial maximum to the Holocene of 10.5 ºC as well as clear Bolling-Allerod and Younger Dryas responses. The amplitude and structure of temperature changes inferred from brGDGTs match well with estimates from pollen, with correlations (r2) as high as 0.88, indicating GDGTs can provide accurate temperature reconstructions. We further observe relationships between brGDGT- and pollen-inferred temperature estimates that suggest GDGT proxies can provide information on vegetation responses to climate changes in

Health risk assessment linked to filling coastal quarries with treated dredged seaport sediments

International Nuclear Information System (INIS)

Perrodin, Yves; Donguy, Gilles; Emmanuel, Evens; Winiarski, Thierry

2014-01-01

Dredged seaport sediments raise complex management problems since it is no longer possible to discharge them into the sea. Traditional waste treatments are poorly adapted for these materials in terms of absorbable volumes and cost. In this context, filling quarries with treated sediments appears interesting but its safety regarding human health must be demonstrated. To achieve this, a specific methodology for assessing health risks has been developed and tested on three seaport sediments. This methodology includes the development of a conceptual model of the global scenario studied and the definition of specific protocols for each of its major steps. The approach proposed includes in particular the use of metrological and experimental tools that are new in this context: (i) an experimental lysimeter for characterizing the deposit emissions, and (ii) a geological radar for identifying potential preferential pathways between the sediment deposit and the groundwater. The application of this approach on the three sediments tested for the scenario studied showed the absence of health risk associated with the consumption of groundwater for substances having a “threshold effect” (risk quotient −6 ). - Highlights: • The release of polluted dredged seaport sediments into the sea must be avoided. • Their use after treatment for the filling-up of quarries is proposed by managers. • An original health risk assessment methodology was created to validate this option. • It includes the use of a lysimeter and a georadar for the exposure assessment stage. • The example studied concludes to a health risk linked to arsenic in the groundwater

Compaction of microfossil and clay-rich chalk sediments

DEFF Research Database (Denmark)

Fabricius, Ida Lykke

2001-01-01

The aim of this study was to evaluate the role of microfossils and clay in the compaction of chalk facies sediments. To meet this aim, chalk sediments with varying micro texture were studied. The sediments have been tested uniaxially confined in a stainless-steel compaction cell. The sediments are......: 1) Pure carbonate chalk with mudstone texture from Stevns Klint (Denmark), 2) Relatively pure chalk sediments with varying content of microfossils from the Ontong Java Plateau (Western Pacific), 3) Clay-rich chalk and mixed sediments from the Caribbean. The tested samples were characterised...

Comparative Test Case Specification

DEFF Research Database (Denmark)

Kalyanova, Olena; Heiselberg, Per

This document includes the specification on the IEA task of evaluation building energy simulation computer programs for the Double Skin Facades (DSF) constructions. There are two approaches involved into this procedure, one is the comparative approach and another is the empirical one. In the comp....... In the comparative approach the outcomes of different software tools are compared, while in the empirical approach the modelling results are compared with the results of experimental test cases. The comparative test cases include: ventilation, shading and geometry....

Evaluation of toxicity to the amphipod, Hyalella azteca, and to the midge, Chironomus dilutus; and bioaccumulation by the oligochaete, Lumbriculus variegatus, with exposure to PCB-contaminated sediments from Anniston, Alabama

Science.gov (United States)

Ingersoll, Christopher G.; Steevens, Jeffery A.; MacDonald, Donald D.; Brumbaugh, William G.; Coady, Matthew R.; Farrar, J. Daniel; Lotufo, Guilherme R.; Kemble, Nile E.; Kunz, James L.; Stanley, Jacob K.; Sinclair, Jesse A.; Ingersoll, Christopher G.; Steevens, Jeffery A.; MacDonald, Donald D.

2014-01-01

characterization of samples of whole sediment included analyses of grain size, TOC, and nutrients. Organic chemical characterization of samples of whole sediment included PCB homologs and select (13) PCB congeners, parent and alkylated polycyclic aromatic hydrocarbons (PAHs), organochlorine pesticides, and polychlorinated dibenzo-p-dioxins; and dibenzofurans. The PCB aroclors analyzed included 1016, 1221, 1232, 1242, 1248, 1254, 1260, 1262 and 1268. Analyses of whole sediment also included total metals, simultaneously extracted metals, and acid volatile sulfide. Chemical characterization of samples of pore water isolated from samples of whole sediment at the start of the sediment toxicity exposures or at the start of the sediment bioaccumulation exposures included metals, major cations, major anions, dissolved organic carbon, and additional water-quality characteristics. Concentrations of metals or PCBs in pore water during the sediment toxicity exposures or during sediment bioaccumulation exposures also were determined using peeper samples (for metals) or solid-phase microextraction (SPME) samplers (for PCBs). The bioavailability and bioaccumulation of PCBs in 14 sediment samples were investigated using SPME passive samplers and the 28-d L. variegatus whole-sediment bioaccumulation exposures In general the accumulation of PCBs consistently was predicted through the use of organic carbon normalization and equilibrium partitioning. In these sediments, PCB homologs were accumulated differently based on bioavailability and potential to accumulate in oligochaetes. As part of this assessment homolog specific biota sediment accumulation factor values were developed that could be applied across the larger site to predict tissue levels of PCBs. The whole-sediment toxicity tests done with H. azteca and C. dilutus met the established ASTM and USEPA test acceptability criteria. The most responsive H. azteca endpoints were day 42 survival normalized young per female and day 28 biomass and

Characterizing toxicity of metal-contaminated sediments from mining areas

Science.gov (United States)

Besser, John M.; Brumbaugh, William G.; Ingersoll, Christopher G.

2015-01-01

This paper reviews methods for testing the toxicity of metals associated with freshwater sediments, linking toxic effects with metal exposure and bioavailability, and developing sediment quality guidelines. The most broadly applicable approach for characterizing metal toxicity is whole-sediment toxicity testing, which attempts to simulate natural exposure conditions in the laboratory. Standard methods for whole-sediment testing can be adapted to test a wide variety of taxa. Chronic sediment tests that characterize effects on multiple endpoints (e.g., survival, growth, and reproduction) can be highly sensitive indicators of adverse effects on resident invertebrate taxa. Methods for testing of aqueous phases (pore water, overlying water, or elutriates) are used less frequently. Analysis of sediment toxicity data focuses on statistical comparisons between responses in sediments from the study area and responses in one or more uncontaminated reference sediments. For large or complex study areas, a greater number of reference sediments is recommended to reliably define the normal range of responses in uncontaminated sediments – the ‘reference envelope’. Data on metal concentrations and effects on test organisms across a gradient of contamination may allow development of concentration-response models, which estimate metal concentrations associated with specified levels of toxic effects (e.g. 20% effect concentration or EC20). Comparisons of toxic effects in laboratory tests with measures of impacts on resident benthic invertebrate communities can help document causal relationships between metal contamination and biological effects. Total or total-recoverable metal concentrations in sediments are the most common measure of metal contamination in sediments, but metal concentrations in labile sediment fractions (e.g., determined as part of selective sediment extraction protocols) may better represent metal bioavailability. Metals released by the weak-acid extraction

Extraction, identification and quantification of heavy metals in Venice lagoon sediments using toxicity tests with microorganisms

Energy Technology Data Exchange (ETDEWEB)

Passarini, F.; Rampazzo, G.; Volpi Ghirardini, A.; Sperni, L.; Salizzato, M.; Pavoni, B. [Venice Univ., Venice (Italy). Dipt. di Scienze Ambientali

2000-02-01

Sediments are the major sink for metal pollutants in the aquatic ecosystem but also an important source for the release of them in the water. In order to assess the contribution of heavy metals to the total sediment toxicity, a methodology that permits to integrate the chemical approach with a direct toxicological approach has been ste up. Toxicological results using Microtox test are compared with analytical results. [Italian] I sedimenti sono il principale deposito per contaminanti metalli nel''ecosistema acquatico, ma anche una fonte importnate di rilascio nell'acqua. Al fine di valutare il contributo dei metalli pesanti alla tossicita' totale del sedimento, e' stata messa a punto una metodologia che permette di integrare l'appoccio chimico con un approccio tossicologico diretto. I risultati dei test di tossicita' Microtox vengono confrontati con i risultati analitici.

Regional Models for Sediment Toxicity Assessment

Science.gov (United States)

This paper investigates the use of empirical models to predict the toxicity of sediment samples within a region to laboratory test organisms based on sediment chemistry. In earlier work, we used a large nationwide database of matching sediment chemistry and marine amphipod sedim...

Comparative study of plutonium and americium bioaccumulation from two marine sediments contaminated in the natural environment

International Nuclear Information System (INIS)

Hamilton, T.F.; Smith, J.D.

1991-01-01

Plutonium and americium sediment-animal transfer was studied under controlled laboratory conditions by exposure of the benthic polychaete Nereis diversicolor (O. F. Mueller) to marine sediments contaminated by a nuclear bomb accident (near Thule, Greenland) and nuclear weapons testing (Enewetak Atoll). In both sediment regimes, the bioavailability of plutonium and 241 Am was low, with specific activity in the tissues 241 Am occurred and 241 Am uptake from the Thule sediment was enhanced compared to that from lagoon sediments of Enewetak Atoll. Autoradiography studies indicated the presence of hot particles of plutonium in the sediments. The results highlight the importance of purging animals of their gut contents in order to obtain accurate estimates of transuranic transfer from ingested sediments into tissue. It is further suggested that enhanced transuranic uptake by some benthic species could arise from ingestion of highly activity particles and organic-rich detritus present in the sediments. (author)

Evaluation of surficial sediment toxicity and sediment physico-chemical characteristics of representative sites in the Lagoon of Venice (Italy)

Science.gov (United States)

Losso, C.; Arizzi Novelli, A.; Picone, M.; Marchetto, D.; Pessa, G.; Molinaroli, E.; Ghetti, P. F.; Volpi Ghirardini, A.

2004-11-01

Toxic hazard in sites with varying types and levels of contamination in the Lagoon of Venice was estimated by means of toxicity bioassays based on the early life-stages of the autochthonous sea urchin Paracentrotus lividus. Elutriate was chosen as the test matrix, due to its ability to highlight potential toxic effects towards sensitive biological components of the water column caused by sediment resuspension phenomena affecting the Lagoon. Surficial sediments (core-top 5 cm deep), directly influenced by resuspension/redeposition processes, and core sediments (core 20 cm deep), recording time-mediated contamination, were sampled in some sites located in the lagoonal area most greatly influenced by anthropogenic activities. Particle size, organic matter and water content were also analysed. In two sites, the results of physical parameters showed that the core-top sediments were coarser than the 20-cm core sediments. Sperm cell toxicity test results showed the negligible acute toxicity of elutriates from all investigated sites. The embryo toxicity test demonstrated a short-term chronic toxicity gradient for elutriates from the 20-cm core sediments, in general agreement both with the expected contamination gradient and with results of the Microtox® solid-phase test. Elutriates of the core-top 5-cm sediments revealed a totally inverted gradient, in comparison with that for the 20-cm core sediments, and the presence of a "hot spot" of contamination in the site chosen as a possible reference. Investigations on ammonia and sulphides as possible confounding factors excluded their contribution to this "hot spot". Integrated physico-chemical and toxicity results on sediments at various depths demonstrated the presence of disturbed sediments in the central basin of the Lagoon of Venice.

Effects of specific inhibitors on anammox and denitrification in marine sediments.

Science.gov (United States)

Jensen, Marlene Mark; Thamdrup, Bo; Dalsgaard, Tage

2007-05-01

The effects of three metabolic inhibitors (acetylene, methanol, and allylthiourea [ATU]) on the pathways of N2 production were investigated by using short anoxic incubations of marine sediment with a 15N isotope technique. Acetylene inhibited ammonium oxidation through the anammox pathway as the oxidation rate decreased exponentially with increasing acetylene concentration; the rate decay constant was 0.10+/-0.02 microM-1, and there was 95% inhibition at approximately 30 microM. Nitrous oxide reduction, the final step of denitrification, was not sensitive to acetylene concentrations below 10 microM. However, nitrous oxide reduction was inhibited by higher concentrations, and the sensitivity was approximately one-half the sensitivity of anammox (decay constant, 0.049+/-0.004 microM-1; 95% inhibition at approximately 70 microM). Methanol specifically inhibited anammox with a decay constant of 0.79+/-0.12 mM-1, and thus 3 to 4 mM methanol was required for nearly complete inhibition. This level of methanol stimulated denitrification by approximately 50%. ATU did not have marked effects on the rates of anammox and denitrification. The profile of inhibitor effects on anammox agreed with the results of studies of the process in wastewater bioreactors, which confirmed the similarity between the anammox bacteria in bioreactors and natural environments. Acetylene and methanol can be used to separate anammox and denitrification, but the effects of these compounds on nitrification limits their use in studies of these processes in systems where nitrification is an important source of nitrate. The observed differential effects of acetylene and methanol on anammox and denitrification support our current understanding of the two main pathways of N2 production in marine sediments and the use of 15N isotope methods for their quantification.

Compound-specific radiocarbon analysis of polycyclic aromatic hydrocarbons (PAHs) in sediments from an urban reservoir

International Nuclear Information System (INIS)

Kanke, Hirohide; Uchida, Masao; Okuda, Tomoaki; Yoneda, Minoru; Takada, Hideshige; Shibata, Yasuyuki; Morita, Masatoshi

2004-01-01

A quantitative apportionment of polycyclic aromatic hydrocarbons (PAHs) derived from fossil fuel combustion ( 14 C-free) and biomass burning (contemporary 14 C) was carried out using a recently developed compound-specific radiocarbon analysis (CSRA) method for a sediment core from an urban reservoir located in the central Tokyo metropolitan area, Japan. The 14 C abundance of PAHs in the sediments was measured by accelerator mass spectrometry (AMS) after extraction and purification by three types of column chromatography, by high performance liquid chromatography (HPLC), and, subsequently, by a preparative capillary gas chromatography (PCGC) system. This method yielded a sufficient quantity of pure compounds and allowed a high degree of confidence in the determination of 14 C. The fraction modern values (f M ) of individual PAHs (phenanthrene, alkylphenanthrenes, fluoranthene, pyrene and benz[a]anthracene) in the sediments ranged from 0.06 to 0.21. These results suggest that sedimentary PAHs (those compounds mentioned above) were derived mostly from fossil fuel combustion. Three sectioned-downcore profiles (∼40 cm) of the 14 C abundance in phenanthrene and alkylphenanthrenes showed a decreasing trend with depth, that was anti-correlated with the trend of ΣPAHs concentration. The f M values of phenanthrene were also larger than those of alkylphenanthrenes in each section of the core. This result indicates that phenanthrene received a greater contribution from biomass burning than alkylphenanthrenes throughout the core. This finding highlights the method used here as an useful approach to elucidate the source and origin of PAHs in the environment

Combining sediment fingerprinting and a conceptual model for erosion and sediment transfer to explore sediment sources in an Alpine catchment

Science.gov (United States)

Costa, A.; Stutenbecker, L.; Anghileri, D.; Bakker, M.; Lane, S. N.; Molnar, P.; Schlunegger, F.

2017-12-01

In Alpine basins, sediment production and transfer is increasingly affected by climate change and human activities, specifically hydropower exploitation. Changes in sediment sources and pathways significantly influence basin management, biodiversity and landscape evolution. We explore the dynamics of sediment sources in a partially glaciated and highly regulated Alpine basin, the Borgne basin, by combining geochemical fingerprinting with the modelling of erosion and sediment transfer. The Borgne basin in southwest Switzerland is composed of three main litho-tectonic units, which we characterised following a tributary-sampling approach from lithologically characteristic sub-basins. We analysed bulk geochemistry using lithium borate fusion coupled with ICP-ES, and we used it to discriminate the three lithologic sources using statistical methods. Finally, we applied a mixing model to estimate the relative contributions of the three sources to the sediment sampled at the outlet. We combine results of the sediment fingerprinting with simulations of a spatially distributed conceptual model for erosion and transport of fine sediment. The model expresses sediment erosion by differentiating the contributions of erosional processes driven by erosive rainfall, snowmelt, and icemelt. Soil erodibility is accounted for as function of land-use and sediment fluxes are linearly convoluted to the outlet by sediment transfer rates for hillslope and river cells, which are a function of sediment connectivity. Sediment connectivity is estimated on the basis of topographic-hydraulic connectivity, flow duration associated with hydropower flow abstraction and permanent storage in hydropower reservoirs. Sediment fingerprinting at the outlet of the Borgne shows a consistent dominance (68-89%) of material derived from the uppermost, highly glaciated reaches, while contributions of the lower part (10-25%) and middle part (1-16%), where rainfall erosion is predominant, are minor. This result is

Laboratory tests for the phytoextraction of heavy metals from polluted harbor sediments using aquatic plants.

Science.gov (United States)

Mânzatu, Carmen; Nagy, Boldizsár; Ceccarini, Alessio; Iannelli, Renato; Giannarelli, Stefania; Majdik, Cornelia

2015-12-30

The aim of this study was to investigate the concentrations and pollution levels of heavy metals, organochlorine pesticides, and polycyclic aromatic hydrocarbons in marine sediments from the Leghorn Harbor (Italy) on the Mediterranean Sea. The phytoextraction capacity of three aquatic plants Salvinia natans, Vallisneria spiralis, and Cabomba aquatica was also tested in the removal of lead and copper, present in high concentration in these sediments. The average detectable concentrations of metals accumulated by the plants in the studied area were as follows: >3.328 ± 0.032 mg/kg dry weight (DW) of Pb and 2.641 ± 0.014 mg/kg DW of Cu for S. natans, >3.107 ± 0.034 g/kg DW for V. spiralis, and >2.400 ± 0.029 mg/kg DW for C. aquatica. The occurrence of pesticides was also analyzed in the sediment sample by gas chromatography coupled with mass spectrometry (GC/MS). Due to its metal and organic compound accumulation patterns, S. natans is a potential candidate in phytoextraction strategies. Copyright © 2015 Elsevier Ltd. All rights reserved.

Sediment studies at Bikini Atoll part 1. distribution of fine and coarse components in surface sediments

International Nuclear Information System (INIS)

Noshkin, V. E.; Eagle, R.J.; Robison, W.L.

1997-01-01

In 1979, 21 years after the moratorium on nuclear testing in the Marshall Islands, surface sediment samples (to depths of 2 and 4 cm) were collected from 87 locations over the floor of Bikini lagoon. The main purpose for the collections was to map the distribution of long- lived man-made radionuclides associated with the bottom material. In addition the samples were processed to estimate the fraction of fine and coarse components to show what modifications occurred since the sediment composition was first described in samples collected before testing in 1946. In this report a comparison is made of the amount and distribution of fine material associated with the lagoon surface sediment before and after the testing of nuclear devices. Nuclear testing produced more finely divided material in-the surface sediment layer over large areas of the lagoon and especially in regions of the lagoon and reef adjacent to test sites. Five cratering events at Bikini Atoll generated sufficient material to account for the inventory of new fine material found over the bottom surface of the lagoon. Although the fraction of fine material in the bottom sediments was altered by the nuclear events, the combined processes of formation, transport and deposition were not sufficiently dynamic to alter the geographical features of the major sedimentary components over most of the lagoon floor

Sediment studies at Bikini Atoll part 1. distribution of fine and coarse components in surface sediments

Energy Technology Data Exchange (ETDEWEB)

Noshkin, V. E.; Eagle, R.J.; Robison, W.L.

1997-01-01

In 1979, 21 years after the moratorium on nuclear testing in the Marshall Islands, surface sediment samples (to depths of 2 and 4 cm) were collected from 87 locations over the floor of Bikini lagoon. The main purpose for the collections was to map the distribution of long- lived man-made radionuclides associated with the bottom material. In addition the samples were processed to estimate the fraction of fine and coarse components to show what modifications occurred since the sediment composition was first described in samples collected before testing in 1946. In this report a comparison is made of the amount and distribution of fine material associated with the lagoon surface sediment before and after the testing of nuclear devices. Nuclear testing produced more finely divided material in-the surface sediment layer over large areas of the lagoon and especially in regions of the lagoon and reef adjacent to test sites. Five cratering events at Bikini Atoll generated sufficient material to account for the inventory of new fine material found over the bottom surface of the lagoon. Although the fraction of fine material in the bottom sediments was altered by the nuclear events, the combined processes of formation, transport and deposition were not sufficiently dynamic to alter the geographical features of the major sedimentary components over most of the lagoon floor.

A Newton-Euler Description for Sediment Movement.

Science.gov (United States)

Maniatis, G.; Hoey, T.; Drysdale, T.; Hodge, R. A.; Valyrakis, M.

2015-12-01

We present progress from the development of a purpose specific sensing system for sediment transport (Maniatis et al. 2013). This system utilises the capabilities of contemporary inertial micro-sensors (strap-down accelerometers and gyroscopes) to record fluvial transport from the moving body-frame of artificial pebbles modelled precisely to represent the motion of real, coarse sediment grains (D90=100 mm class). This type of measurements can be useful in the context of sediment transport only if the existing mathematical understanding of the process is updated. We test a new mathematical model which defines specifically how the data recorded in the body frame of the sensor (Lagrangian frame of reference) can be generalised to the reference frame of the flow (channel, Eulerian frame of reference). Given the association of the two most widely used models for sediment transport with those frames of reference (Shields' to Eulerian frame and HA. Einstein's to Lagrangian frame), this description builds the basis for the definition of explicit incipient motion criteria (Maniatis et al. 2015) and for the upscaling from point-grain scale measurements to averaged, cross-sectional, stream related metrics. Flume experiments where conducted in the Hydraulics laboratory of the University of Glasgow where a spherical sensor of 800 mm diameter and capable of recoding inertial dynamics at 80Hz frequency was tested under fluvial transport conditions. We managed to measure the dynamical response of the unit during pre-entrainment/entrainment transitions, on scaled and non-scaled to the sensor's diameter bed and for a range of hydrodynamic conditions (slope up to 0.02 and flow increase rate up to 0.05m3.s-1. Preliminary results from field deployment on a mixed bedrock-alluvial channel are also presented. Maniatis et. al 2013 J. Sens. Actuator Netw. 2013, 2(4), 761-779; Maniatis et. al 2015: "CALCULATION OF EXPLICIT PROBABILITY OF ENTRAINMENT BASED ON INERTIAL ACCELERATION

Surface-specific additive manufacturing test artefacts

Science.gov (United States)

Townsend, Andrew; Racasan, Radu; Blunt, Liam

2018-06-01

Many test artefact designs have been proposed for use with additive manufacturing (AM) systems. These test artefacts have primarily been designed for the evaluation of AM form and dimensional performance. A series of surface-specific measurement test artefacts designed for use in the verification of AM manufacturing processes are proposed here. Surface-specific test artefacts can be made more compact because they do not require the large dimensions needed for accurate dimensional and form measurements. The series of three test artefacts are designed to provide comprehensive information pertaining to the manufactured surface. Measurement possibilities include deviation analysis, surface texture parameter data generation, sub-surface analysis, layer step analysis and build resolution comparison. The test artefacts are designed to provide easy access for measurement using conventional surface measurement techniques, for example, focus variation microscopy, stylus profilometry, confocal microscopy and scanning electron microscopy. Additionally, the test artefacts may be simply visually inspected as a comparative tool, giving a fast indication of process variation between builds. The three test artefacts are small enough to be included in every build and include built-in manufacturing traceability information, making them a convenient physical record of the build.

Evaluation through column leaching tests of metal release from contaminated estuarine sediment subject to CO2 leakages from Carbon Capture and Storage sites

International Nuclear Information System (INIS)

Payán, M. Cruz; Galan, Berta; Coz, Alberto; Vandecasteele, Carlo; Viguri, Javier R.

2012-01-01

The pH change and the release of organic matter and metals from sediment, due to the potential CO 2 acidified seawater leakages from a CCS (Carbon Capture and Storage) site are presented. Column leaching test is used to simulate a scenario where a flow of acidified seawater is in contact with recent contaminated sediment. The behavior of pH, dissolved organic carbon (DOC) and metals As, Cd, Cr, Cu, Ni, Pb, Zn, with liquid to solid (L/S) ratio and pH is analyzed. A stepwise strategy using empirical expressions and a geochemical model was conducted to fit experimental release concentrations. Despite the neutralization capacity of the seawater-carbonate rich sediment system, important acidification and releases are expected at local scale at lower pH. The obtained results would be relevant as a line of evidence input of CCS risk assessment, in an International context where strategies to mitigate the climate change would be applied. - Highlights: ► Tier structured approach for assessment of the release of metals from sediment. ► Standard column leaching test to simulate CO 2 acidified seawater CCS leakages. ► Metal and DOC release from marine sediment in contact to CO 2 acidified seawater. ► From empirical to geochemical modeling approaches of DOC and metals release in column tests. ► Contamination line of evidence input of CCS risk assessment. - Column metal release from CO 2 acidified seawater leakages in contact with estuarine contaminated sediment in CCS sites

Biological and chemical characterization of harbour sediments from the Stockholm area

Energy Technology Data Exchange (ETDEWEB)

Eklund, Britta; Elfstroem, Maria; Bengtsson, Bengt-Erik; Breitholtz, Magnus [Dept. of Applied Environmental Science (ITM), Stockholm Univ. (Sweden); Gallego, Irene [Granada Univ. (Spain)

2010-01-15

Purpose: The main objective of the current study was to assess the impact of pleasure boat activities on harbour sediment quality in the Stockholm area. Sediment contamination is a growing ecological issue, and there is consequently a need to use sediment bioassays in combination with chemical analysis to determine the impact on the ecosystem. To generate sediment toxicity data relevant for the Baltic Sea, a secondary objective was to further develop and evaluate two well-established bioassays for saltwater, with the macroalga Ceramium tenuicorne and the crustacean Nitocra spinipes, to be useful also for toxicity testing of whole sediment. A major concern has been to minimize any manipulation of the sediments. A third objective was to assess whether a simple leaching procedure could be used to simulate sediment toxicity by comparing results from whole sediment and leachate tests. Materials and methods: Surface sediments (0-2 cm) from five different types of pleasure boat harbours were collected. Chemical measurements of boat related compounds, i.e. tin organic substances (tributyltin (TBT), dibutyl tin, and monobutyl tin), polyaromatic hydrocarbons (PAHs), copper, zinc, lead, tin and irgarol were conducted. The sediments were tested for toxic effects using the established Microtox {sup registered} test as well as the developed sediment tests with C. tenuicorne and N. spinipes. The endpoints are growth inhibition for the algal test and for the crustacean test mortality of larvae and rate of development expressed as the ratio between nauplia and copepodites. Two different procedures have been compared with both organisms, i.e. exposure to whole sediment and to leachate. The duration of both tests is around 1 week. Results and discussion: All harbour locations were more or less heavily contaminated with remnants from use of antifouling paints. The sediment in a smaller marina (ca. 250 boats) contained the highest levels of TBT (max 1,400 {mu}g/kg dry weight (dw

A comprehensive test specification for pulse fission counters

Energy Technology Data Exchange (ETDEWEB)

Roberts, D L [Control and Instrumentation Division, Atomic Energy Establishment, Winfrith, Dorchester, Dorset (United Kingdom)

1962-02-15

The following test specification is based on the memorandum AERE - M 728 which it now replaces It contains a standard acceptance test procedure for the many U.K.A.E.A, designed pulse fission counters now commercially available. This test specification may be used for any pulse fission counter provided a specification sheet as shown in Appendix 3 is supplied to the contractor quoting this report and including specified values for the measured quantities. (author)

Background radioactivity in sediments near Los Alamos, New Mexico

International Nuclear Information System (INIS)

McLin, Stephen G.

2004-01-01

River and reservoir sediments have been collected annually by Los Alamos National Laboratory since 1974 and 1979, respectively. These background samples are collected from five river stations and four reservoirs located throughout northern New Mexico and southern Colorado. Analyses include 3 H, 90 Sr, 137 Cs, total U, 238 Pu, 239,240 Pu, 241 Am, gross alpha, gross beta, and gross gamma radioactivity. Surprisingly, there are no federal or state regulatory standards in the USA that specify how to compute background radioactivity values on sediments. Hence, the sample median (or 0.50 quantile) is proposed for this background because it reflects central data tendency and is distribution-free. Estimates for the upper limit of background radioactivity on river and reservoir sediments are made for sampled analytes using the 0.95 quantile (two-tail). These analyses also show that seven of ten analytes from reservoir sediments are normally distributed, or are normally distributed after a logarithmic or square root transformation. However, only three of ten analytes from river sediments are similarly distributed. In addition, isotope ratios for 137 Cs/ 238 Pu, 137 Cs/ 239,240 Pu, and 239,240 Pu/ 238 Pu from reservoir sediments are independent of clay content, total organic carbon/specific surface area (TOC/SSA) and cation exchange capacity/specific surface area (CEC/SSA) ratios. These TOC/SSA and CEC/SSA ratios reflect sediment organic carbon and surface charge densities that are associated with radionuclide absorption, adsorption, and ion exchange reactions on clay mineral structures. These latter ratio values greatly exceed the availability of background radionuclides in the environment, and insure that measured background levels are a maximum. Since finer-grained reservoir sediments contain larger clay-sized fractions compared to coarser river sediments, they show higher background levels for most analytes. Furthermore, radioactivity values on reservoir sediments have

Sediment core fossils in ancient Lake Ohrid: testing for faunal change since the Last Interglacial

Directory of Open Access Journals (Sweden)

C. Albrecht

2010-11-01

Full Text Available Ancient Lake Ohrid is probably of early Pleistocene or Pliocene origin and amongst the few lakes in the world harbouring an outstanding degree of endemic biodiversity. Although there is a long history of evolutionary research in Lake Ohrid, particularly on molluscs, a mollusc fossil record has been missing up to date. For the first time, gastropod and bivalve fossils are reported from the basal, calcareous part of a 2.6 m long sediment succession (core Co1200 from the north-eastern part of Lake Ohrid. Electron spin resonance (ESR dating of mollusc shells from the same stratigraphic level yielded an age of 130 ± 28 ka. Lithofacies III sediments, i.e. a stratigraphic subdivision comprising the basal succession of core Co1200 between 181.5–263 cm, appeared solid, greyish-white, and consisted almost entirely of silt-sized endogenic calcite (CaCO₃>70% and intact and broken mollusc shells. Here we compare the faunal composition of the thanatocoenosis with recent mollusc associations in Lake Ohrid. A total of 13 mollusc species (9 gastropod and 4 bivalve species could be identified within Lithofacies III sediments. The value of sediment core fossils for reconstructing palaeoenvironmental settings was evaluated and the agreement between sediment and palaeontological proxies was tested.

The study also aims at investigating major faunal changes since the Last Interglacial and searching for signs of extinction events.

The combined findings of the ecological study and the sediment characteristics suggest deposition in a shallow water environment during the Last Interglacial. The fossil fauna exclusively included species also found in the present fauna, i.e. no extinction events are evident for this site since the Last Interglacial. The thanatocoenosis showed the highest similarity with recent Intermediate Layer (5–25 m water depth mollusc assemblages. The demonstrated existence of a mollusc fossil record in Lake Ohrid

Leishmania (infantum) chagasi in canine urinary sediment

OpenAIRE

Mendonça, Ivete Lopes de; Batista, Joilson Ferreira; Alves, Leucio Camara

2015-01-01

Canine visceral leishmaniasis (CVL) is difficult to diagnosis, mainly due to the presence of asymptomatic animals, the diversity of clinical symptoms and the difficulty in obtaining diagnostic evidence of high sensitivity and specificity. The purpose of this study was to diagnose CVL in urinary sediment of 70 dogs of different breeds, sexes and ages from the veterinary hospital of the Federal University of Piauí and Zoonosis Control Center of Teresina, Brazil. The serological tests were TR DP...

Application of dimensionless sediment rating curves to predict suspended-sediment concentrations, bedload, and annual sediment loads for rivers in Minnesota

Science.gov (United States)

Ellison, Christopher A.; Groten, Joel T.; Lorenz, David L.; Koller, Karl S.

2016-10-27

-of-fit that included proximity of the model(s) fitted line to the 95-percent confidence intervals of the site-specific model, Nash-Sutcliffe Efficiency values, model biases, and deviation of annual sediment loads from each model to the annual sediment loads calculated from measured data.Composite plots comparing Pagosa Springs DSRCs, Minnesota DSRCs, site-specific regression models, and measured data indicated that regionally developed DSRCs (Minnesota DSRC models) more closely approximated measured data for nearly every site. Pagosa Springs DSRC models had markedly larger exponents (slopes) when compared to the Minnesota DSRC models and the site-specific regression models, and over-represent SSC and bedload at streamflows exceeding bankfull. The Nash-Sutcliffe Efficiency values for the Minnesota DSRC model for suspended-sediment concentrations closely matched Nash-Sutcliffe Efficiency values of the site-specific regression models for 12 out of 16 sites. Nash-Sutcliffe Efficiency values associated with Minnesota DSRCs were greater than those associated with Pagosa Springs DSRCs for every site except the Whitewater River near Beaver, Minnesota site. Pagosa Springs DSRC models were less accurate than the mean of the measured data at predicting SSC values for one-half of the sites for good/fair stability sites and one-half of the sites for poor stability sites. Relative model biases were calculated and determined to be substantial (greater than 5 percent) for Pagosa Springs and Minnesota models, with Minnesota models having a lower mean model bias. For predicted annual suspended-sediment loads (SSL), the Minnesota DSRC models for good/fair and poor stream stability sites more closely approximated the annual SSLs calculated from the measured data as compared to the Pagosa Springs DSRC model.Results of data analyses indicate that DSRC models developed using data collected in Minnesota were more effective at compensating for differences in individual stream characteristics across a

Quality assurance of radiopharmaceuticals - specifications and test procedures

International Nuclear Information System (INIS)

Baldas, J.; Bonnyman, J.; Colmanet, S.F.; Ivanov, Z.; Lauder, R.A.

1990-10-01

The authors report on a Radiopharmaceutical Quality Assurance Test Programme carried out by the Australian Radiation Laboratory in which radiopharmaceuticals used in nuclear medicine in Australia are tested for compliance with specifications. Where the radiopharmaceutical is the subject of a monograph in the British Pharmacopoeia or the European Pharmacopoeia, then the specifications given in the Pharmacopoeia are adopted. In other cases the specifications given have been adopted by this Laboratory and have no legal status. In some cases test procedures described have been taken from various Pharmacopoeias or methods published in the literature. In other cases test methods described have been developed at this Laboratory. It should be noted that, unless stated otherwise, specifications listed apply at all times up until product expire

Health risk assessment linked to filling coastal quarries with treated dredged seaport sediments

Energy Technology Data Exchange (ETDEWEB)

Perrodin, Yves, E-mail: yves.perrodin@entpe.fr [Université de Lyon, ENTPE, UMR CNRS 5023, Laboratoire LEHNA, 2 rue Maurice Audin, 69518 Vaulx-en-Velin (France); Donguy, Gilles [Université de Lyon, ENTPE, UMR CNRS 5023, Laboratoire LEHNA, 2 rue Maurice Audin, 69518 Vaulx-en-Velin (France); Emmanuel, Evens [Laboratoire de Qualité de l' Eau et de l' Environnement, Université Quisqueya, BP 796 Port-au-Prince (Haiti); Winiarski, Thierry [Université de Lyon, ENTPE, UMR CNRS 5023, Laboratoire LEHNA, 2 rue Maurice Audin, 69518 Vaulx-en-Velin (France)

2014-07-01

Dredged seaport sediments raise complex management problems since it is no longer possible to discharge them into the sea. Traditional waste treatments are poorly adapted for these materials in terms of absorbable volumes and cost. In this context, filling quarries with treated sediments appears interesting but its safety regarding human health must be demonstrated. To achieve this, a specific methodology for assessing health risks has been developed and tested on three seaport sediments. This methodology includes the development of a conceptual model of the global scenario studied and the definition of specific protocols for each of its major steps. The approach proposed includes in particular the use of metrological and experimental tools that are new in this context: (i) an experimental lysimeter for characterizing the deposit emissions, and (ii) a geological radar for identifying potential preferential pathways between the sediment deposit and the groundwater. The application of this approach on the three sediments tested for the scenario studied showed the absence of health risk associated with the consumption of groundwater for substances having a “threshold effect” (risk quotient < 1), and an acceptable risk for substances having a “non-threshold effect”, with the notable exception of arsenic (individual risk equal to 3.10{sup −6}). - Highlights: • The release of polluted dredged seaport sediments into the sea must be avoided. • Their use after treatment for the filling-up of quarries is proposed by managers. • An original health risk assessment methodology was created to validate this option. • It includes the use of a lysimeter and a georadar for the exposure assessment stage. • The example studied concludes to a health risk linked to arsenic in the groundwater.

Investigation of mechanical properties of hydrate-bearing pressure core sediments recovered from the Eastern Nankai Trough using transparent acrylic cell triaxial testing system (TACTT-system)

Science.gov (United States)

Yoneda, J.; Masui, A.; Konno, Y.; Jin, Y.; Kida, M.; Suzuki, K.; Nakatsuka, Y.; Tenma, N.; Nagao, J.

2014-12-01

Natural gas hydrate-bearing pressure core sediments have been sheared in compression using a newly developed Transparent Acrylic Cell Triaxial Testing (TACTT) system to investigate the geophysical and geomechanical behavior of sediments recovered from the deep seabed in the Eastern Nankai Trough, the first Japanese offshore production test region. The sediments were recovered by hybrid pressure core system (hybrid PCS) and pressure cores were cut by pressure core analysis tools (PCATs) on board. These pressure cores were transferred to the AIST Hokkaido centre and trimmed by pressure core non-destructive analysis tools (PNATs) for TACTT system which maintained the pressure and temperature conditions within the hydrate stability boundary, through the entire process of core handling from drilling to the end of laboratory testing. An image processing technique was used to capture the motion of sediment in a transparent acrylic cell, and digital photographs were obtained at every 0.1% of vertical strain during the test. Analysis of the optical images showed that sediments with 63% hydrate saturation exhibited brittle failure, although nonhydrate-bearing sediments exhibited ductile failure. In addition, the increase in shear strength with hydrate saturation increase of natural gas hydrate is in agreement with previous data from synthetic gas hydrate. This research was financially supported by the Research Consortium for Methane Hydrate Resources in Japan (MH21 Research Consortium) that carries out Japan's Methane Hydrate R&D Program by the Ministry of Economy, Trade and Industry (METI).

Ecotoxicological risk assessment linked to infilling quarries with treated dredged seaport sediments.

Science.gov (United States)

Perrodin, Yves; Donguy, Gilles; Bazin, Christine; Volatier, Laurence; Durrieu, Claude; Bony, Sylvie; Devaux, Alain; Abdelghafour, Mohammed; Moretto, Robert

2012-08-01

The dredged sediments of polluted seaports now raise complex management problems since it is no longer possible to discharge them into the sea. This results in the need to manage them on land, raising other types of technical, economic and environmental problems. Regarding the technical and economic dimensions, traditional waste treatment methods have proved to be poorly adapted, due to very high costs and low absorbable volumes. In this context, filling quarries in coastal areas with treated sediments could represent an interesting alternative for these materials. Nevertheless, for the environmental dimension, it is necessary to demonstrate that this possibility is harmless to inland ecosystems. Consequently, a specific ecotoxicological risk assessment methodology has been formulated and tested on three sediments taken from seaboards of France, in view to providing an operational and usable tool for the prior validation of any operation to fill quarries with treated seaport sediments. This method incorporates the formulation of a global conceptual model of the scenario studied and the definition of protocols for each of its steps: the characterisation of exposures (based on a simulation of sediment deposit), the characterisation of effects (via the study of sediments ecotoxicity), and the final ecotoxicological risk assessment performed as a calculation of a risk quotient. It includes the implementation in parallel of two types of complementary approach: the "substances" approach derived from the European methodology for assessing new substances placed on the market, and the "matrix" approach which is similar to methods developed in France to assess ecological risks in other domains (waste management, polluted site management, …). The application of this dual approach to the three sediments tested led to conclude with reliability that the project to deposit sediments "1" and "2" presented a low risk for the peripheral aquatic ecosystems while sediment "3

Seasonally and regionally determined indication potential of bioassays in contaminated river sediments.

Science.gov (United States)

Hilscherová, Klára; Dusek, Ladislav; Sídlová, Tereza; Jálová, Veronika; Cupr, Pavel; Giesy, John P; Nehyba, Slavomír; Jarkovský, Jirí; Klánová, Jana; Holoubek, Ivan

2010-03-01

River sediments are a dynamic system, especially in areas where floods occur frequently. In the present study, an integrative approach is used to investigate the seasonal and spatial dynamics of contamination of sediments from a regularly flooded industrial area in the Czech Republic, which presents a suitable model ecosystem for pollutant distribution research at a regional level. Surface sediments were sampled repeatedly to represent two different hydrological situations: spring (after the peak of high flow) and autumn (after longer period of low flow). Samples were characterized for abiotic parameters and concentrations of priority organic pollutants. Toxicity was assessed by Microtox test; genotoxicity by SOS-chromotest and green fluorescent protein (GFP)-yeast test; and the presence of compounds with specific mode of action by in vitro bioassays for dioxin-like activity, anti-/androgenicity, and anti-/estrogenicity. Distribution of organic contaminants varied among regions and seasonally. Although the results of Microtox and genotoxicity tests were relatively inconclusive, all other specific bioassays led to statistically significant regional and seasonal differences in profiles and allowed clear separation of upstream and downstream regions. The outcomes of these bioassays indicated an association with concentrations of polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) as master variables. There were significant interrelations among dioxin-like activity, antiandrogenicity and content of organic carbon, clay, and concentration of PAHs and PCBs, which documents the significance of abiotic factors in accumulation of pollutants. The study demonstrates the strength of the specific bioassays in indicating the changes in contamination and emphasizes the crucial role of a well-designed sampling plan, in which both spatial and temporal dynamics should be taken into account, for the correct interpretations of information in risk assessments.

Use of bioassays for testing soils and/or sediments contaminated by mining activities

Science.gov (United States)

Pérez-Sirvent, C.; Martínez-Sánchez, M. J.; García-Lorenzo, M. L.; Molina, J.

2009-04-01

Ecotoxicity tests measure the bioavailability of the contaminants and the effects of the chemically not measured toxic compounds on the members of the soil community. Therefore, ecotoxicological testing may be a useful approach for assessing the toxicity as a complement to chemical analysis. They are solid phase tests based on terrestrial methods and tests performed on water extracts using aquatic test protocols. The extent and degree of heavy metal contamination around mines may vary depending on geochemical characteristics, the mineralization of tailings, physico-chemical conditions and the processes used to extract metals. Portman Bay was subject to mining from the time of the Roman Empire to 1991 when the activity ceased. Since 1957, the wastes from mining operations were discharged directly into the sea. These wastes mainly consisted of clay, quartz, siderite, magnetite, remains of sphalerite, pyrite and galena and residues of the chemical reagents used in floatation. In our study two methods of environmental toxicological tests were compared and applied to sediments of the Portman Bay (SE, Spain): the standardized toxicological test based on inhibition of luminescence employing Microtox

Comparative study of plutonium and americium bioaccumulation from two marine sediments contaminated in the natural environment

Energy Technology Data Exchange (ETDEWEB)

Hamilton, T.F.; Smith, J.D. (Melbourne Univ., Parkville (Australia). Dept. of Inorganic Chemistry); Fowler, S.W.; LaRosa, J.; Holm, E. (International Atomic Energy Agency, Monaco-Ville (Monaco). Lab. of Marine Radioactivity); Aarkrog, A.; Dahlgaard, H. (Risoe National Lab., Roskilde (Denmark))

1991-01-01

Plutonium and americium sediment-animal transfer was studied under controlled laboratory conditions by exposure of the benthic polychaete Nereis diversicolor (O. F. Mueller) to marine sediments contaminated by a nuclear bomb accident (near Thule, Greenland) and nuclear weapons testing (Enewetak Atoll). In both sediment regimes, the bioavailability of plutonium and {sup 241}Am was low, with specific activity in the tissues <1% (dry wt) than in the sediments. Over the first three months, a slight preference in transfer of plutonium over {sup 241}Am occurred and {sup 241}Am uptake from the Thule sediment was enhanced compared to that from lagoon sediments of Enewetak Atoll. Autoradiography studies indicated the presence of hot particles of plutonium in the sediments. The results highlight the importance of purging animals of their gut contents in order to obtain accurate estimates of transuranic transfer from ingested sediments into tissue. It is further suggested that enhanced transuranic uptake by some benthic species could arise from ingestion of highly activity particles and organic-rich detritus present in the sediments. (author).

Cyber-Physical Energy Systems Modeling, Test Specification, and Co-Simulation Based Testing

DEFF Research Database (Denmark)

van der Meer, A. A.; Palensky, P.; Heussen, Kai

2017-01-01

The gradual deployment of intelligent and coordinated devices in the electrical power system needs careful investigation of the interactions between the various domains involved. Especially due to the coupling between ICT and power systems a holistic approach for testing and validating is required....... Taking existing (quasi-) standardised smart grid system and test specification methods as a starting point, we are developing a holistic testing and validation approach that allows a very flexible way of assessing the system level aspects by various types of experiments (including virtual, real......, and mixed lab settings). This paper describes the formal holistic test case specification method and applies it to a particular co-simulation experimental setup. The various building blocks of such a simulation (i.e., FMI, mosaik, domain-specific simulation federates) are covered in more detail...

Luminescence dating of Netherland's sediments

NARCIS (Netherlands)

Wallinga, J.; Davids, F.; Dijkmans, J.W.A.

2007-01-01

Over the last decades luminescence dating techniques have been developed that allow earth scientists to determine the time of deposition of sediments. In this contribution we revity: 1) the development of the methodology, 2) tests of the reliability of luminescence dating on Netherlands' sediments;

Results of bulk sediment analysis and bioassay testing on selected sediments from Oakland Inner Harbor and Alcatraz disposal site, San Francisco, California

International Nuclear Information System (INIS)

Word, J.Q.; Ward, J.A.; Woodruff, D.L.

1990-09-01

The Battelle/Marine Sciences Laboratory (MSL) was contracted by the US Army Corps of Engineers, San Francisco District, to perform bulk sediment analysis and oyster larvae bioassays (elutriate) on sediments from Inner Oakland Harbor, California. Analysis of sediment characteristics by MSL indicated elevated priority pollutants, PAHs, pesticides, metals, organotins, and oil and grease concentrations, when compared to Alcatraz Island Dredged Material Disposal Site sediment concentrations. Larvae of the Pacific oyster, Crassostrea gigas, were exposed to seawater collected from the Alcatraz Island Site water, and a series of controls using water and sediments collected from Sequim Bay, Washington. Exposure of larvae to the Alcatraz seawater and the 50% and 100% elutriate concentrations from each Oakland sediment resulted in low survival and a high proportion of abnormal larvae compared to Sequim Bay control exposures. MSL identified that field sample collection, preservation, and storage protocols used by Port of Oakland contractors were inconsistent with standard accepted practices. 23 refs., 10 figs., 40 tabs

Testing of badminton specific endurance

DEFF Research Database (Denmark)

Madsen, Christian Møller; Højlyng, Mads; Nybo, Lars

2016-01-01

In the present study, a novel intermittent badminton endurance test (B-ENDURANCE) was developed and tested in elite (n=17) and skilled (n=9) badminton players as well as in age-matched physically active men (non-badminton players; n=8). In addition, B-ENDURANCE test-retest reproducibility...... was evaluated in nine badminton players.B-ENDURANCE is an incremental test where each level consists of repeated sequences of badminton specific actions towards the four corners on the court. The subject starts in the center of the court in front of a computer screen and within each sequence he must...... decreases until the subjects cannot follow the dictated tempo.B-ENDURANCE performance for elite players was better (Pbadminton players. In addition, B-ENDURANCE performance correlated (r=0.8; P

Targeting sediment management strategies using sediment quantification and fingerprinting methods

Science.gov (United States)

Sherriff, Sophie; Rowan, John; Fenton, Owen; Jordan, Phil; hUallacháin, Daire Ó.

2016-04-01

statistically un-mixed using FR2000, an uncertainty-inclusive algorithm, and combined with sediment yield data. Results showed sediment contributions from channel, field and road groups were 70%, 25% and 5% in the poorly-drained catchment, 59%, 22% and 19% in the well-drained catchment, and 17%, 74% and 9% in the moderately-drained catchment. Higher channel contributions in the poorly-drained catchment were attributed to bank erosion accelerated by the rapid diversion of surface runoff into channels, facilitated by surface and sub-surface artificial drainage networks, and bank seepage from lateral pressure gradients due to confined groundwater. Despite the greatest proportion of arable soils in the well-drained catchment, this source was frequently hydrologically disconnected as well-drained soils largely infiltrated rainfall and prevented surface soil erosion. Periods of high and intense rainfall were associated with greater proportions of field losses in the well-drained catchment likely due to infiltration exceeding the saturated hydraulic conductivity of soils and establishment of surface hydrological connectivity. Losses from field topsoils dominated in the moderately-drained catchment as antecedent soil wetness maintained surface flow pathways and coincided with low groundcover on arable soils. For cost-effective management of sediment pressures to aquatic ecosystems, catchment specific variations in sediment sources must be considered.

Toxicity and bioaccumulation of sediment-associated contaminants using freshwater invertebrates: A review of methods and applications

Science.gov (United States)

Ingersoll, C.G.; Ankley, G.T.; Benoit, D.A.; Brunson, E.L.; Burton, G.A.; Dwyer, F.J.; Hoke, R.A.; Landrum, P.F.; Norberg-King, T. J.; Winger, P.V.

1995-01-01

This paper reviews recent developments in methods for evaluating the toxicity and bioaccumulation of contaminants associated with freshwater sediments and summarizes example case studies demonstrating the application of these methods. Over the past decade, research has emphasized development of more specific testing procedures for conducting 10-d toxicity tests with the amphipod Hyalella azteca and the midge Chironomus tentans. Toxicity endpoints measured in these tests are survival for H. azteca and survival and growth for C. tentans. Guidance has also been developed for conducting 28-d bioaccumulation tests with the oligochaete Lumbriculus variegatus, including determination of bioaccumulation kinetics for different compound classes. These methods have been applied to a variety of sediments to address issues ranging from site assessments to bioavailability of organic and inorganic contaminants using field-collected and laboratory-spiked samples. Survival and growth of controls routinely meet or exceed test acceptability criteria. Results of laboratory bioaccumulation studies with L. variegatus have been confirmed with comparisons to residues (PCBs, PAHs, DDT) present from synoptically collected field populations of oligochaetes. Additional method development is currently underway to develop chronic toxicity tests and to provide additional data-confirming responses observed in laboratory sediment tests with natural benthic populations.

Standard specification for agencies performing nondestructive testing

CERN Document Server

American Society for Testing and Materials. Philadelphia

2009-01-01

1.1 This specification covers minimum requirements for agencies performing nondestructive testing (NDT). 1.2 When using this specification to assess the capability of, or to accredit NDT agencies, Guide E 1359 shall be used as a basis for the survey. It can be supplemented as necessary with more detail in order to meet the auditor's specific needs. 1.3 This specification can be used as a basis to evaluate testing or inspection agencies, or both, and is intended for use for the qualifying or accrediting, or both, of testing or inspection agencies, public or private. 1.4 The use of SI or inch-pound units, or combination thereof, will be the responsibility of the technical committee whose standards are referred to in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to...

Specification-based testing: What is it? How can it be automated?

International Nuclear Information System (INIS)

Poston, R.M.

1994-01-01

Software testing should begin with a written requirements specification. A specification states how software is expected to behave and describes operational characteristics (performance, reliability, etc.) for the software. A specification serves as a reference or base to test against, giving rise to the name, specification-based testing. Should analysts or designers fail to write a specification, then testers are obliged to write their own specification to test against. Specifications written by testers may be called test plans or test objectives

Tests in Print II: An Index to Tests, Test Reviews, and the Literature on Specific Tests.

Science.gov (United States)

Buros, Oscar K., Ed.

Tests in Print II is a comprehensive, annotated bibliography of all in-print tests published as separates for use with English-speaking subjects. The 1,155 two-column pages list 2,467 tests in print as of early 1974; 16,574 references through 1971 on specific tests; a reprinting of the 1974 APA-AERA-NCME Standards for Educational andPsychological…

Sediment studies at Bikini Atoll part 2. inventories of transuranium elements in surface sediments

Energy Technology Data Exchange (ETDEWEB)

Noshkin, V.E.; Eagle, R.J.; Wong, K.M.; Robison, W.L.

1997-10-01

This is the second of three reports on Bikini sediment studies, which discusses the concentrations and inventories of {sup 241}Am and {sup 239+240}Pu in sediments from the lagoon. Surface sediment samples were collected from 87 locations over the entire lagoon at Bikini Atoll during 1979. The collections were made to map the distribution of long-lived radionuclides associated with the bottom material and to show what modifications occurred in the composition of the sediment as a result of the testing program. Present inventories for {sup 241}Am and {sup 239+240}Pu in the surface 2 cm of sediment are estimated to be 14 and 17 TBq, respectively. These values are estimated to represent only 14% of the total inventory in the sediment column. Sediment inventories of {sup 239+240}Pu and {sup 241}Am are changing only slowly with time through chemical- physical processes that continuously mobilize small amounts of the transuranics to the water column. The lowest concentrations and inventories are associated with deposits logoonward of the eastern reef.

Empirical Test Case Specification

DEFF Research Database (Denmark)

Kalyanova, Olena; Heiselberg, Per

This document includes the empirical specification on the IEA task of evaluation building energy simulation computer programs for the Double Skin Facades (DSF) constructions. There are two approaches involved into this procedure, one is the comparative approach and another is the empirical one. I....... In the comparative approach the outcomes of different software tools are compared, while in the empirical approach the modelling results are compared with the results of experimental test cases....

Isotopic method of testing the dynamics of melt flow through a sedimentation tank

International Nuclear Information System (INIS)

Bazaniak, Z.; Chamer, R.; Stec, J.; Przybytniak, W.

1981-01-01

The isotopic method of a simultaneous measurement of copper matte and slag flow parameters is discussed. For marking Cu-64 and Zr 95/97, isotopes characterized by various gamma radiation energy are used. The chemical form of copper and zirconium compounds was chosen from the viewpoint of assuring a selective solubility in the tested phases. To interpret the results of isotopic tests, the Wolf-Resnick model was made. The obtained results have confirmed the hypothesis of a possible occurrence of the copper matte flotation effect. In order to reduce of copper uplifted with the shaft slag, a redesigning is suggested of the sedimentation tank that would assure a reduction of the ideal mixing participation and an increase of the zone characterized by the piston flow. (author)

Dynamics of suspended sediment concentration, flow discharge and sediment particle size interdependency to identify sediment source

Science.gov (United States)

Sadeghi, Seyed Hamidreza; Singh, Vijay P.

2017-11-01

Spatiotemporal behavior of sediment yield is a key for proper watershed management. This study analyzed statistical characteristics and trends of suspended sediment concentration (SCS), flow discharge (FD) and sediment particle sizes using data from 24 gage stations scattered throughout the United States. Analysis showed significant time- and location-specific differences of these variables. The median values of SSC, FD and percentage of particle sizes smaller than 63 μm (P63) for all 24 gage stations were found to be 510.236 mg l-1 (right skewed), 45.406 m3 s-1 (left skewed) and 78.648% (right skewed), respectively. Most of the stations exhibited significant trends (P practices which may call for local or regional planning based on natural (i.e., precipitation amount, type and erosivity, watershed area, and soil erodibility) and human-affected (i.e., land use and hydraulic structures and water resources management) factors governing the study variables.

Stabilization / solidification of polluted marine dredged sediment of port en Bessin France, using hydraulic binders and silica fume

Science.gov (United States)

Silitonga, Ernesto

2017-09-01

A large amount of sediment is dredged in France every year. Due to the increase of the amount of marine dredged sediments, environmentally reuse of dredged sediment is urgently needed in France. The first objective of this study is to find an application for reuse of marine dredged sediments materials, as new material for road construction. Hence, serial tests need to be realized to identify if marine dredged sediment could be utilized for road construction. The second goal is to enhance the physical, mechanical and chemical characteristics of the mix, by incorporating binders and sediments, and revealed the identification of the mechanical characteristics measured on the mixes is compatible with their use as a base course material. The results show that the treatment by hydraulics binders could satisfy the needed mechanical characteristics. The present of Silica Fume is aimed to reduce the pollution level, especially the heavy metal content. However, the proportion of hydraulics binders and silica fume needed to meet prescribed specification is important, so the reuse of the marine dredged sediments of Port-en-Bessin, France in road construction, as an alternative material could be achieved. After the geotechnical study in laboratory results shown as expected than the study to identify the chemical characteristic realized. To evaluate the environmental impacts of the used material, leaching test is performed. The leaching test was performed to verify the predicted release of pollutants based on total dissolution. And for the final part, the test results show that the polluted marine dredged sediments could be safely used (in term of environmental impact) as a new material in road construction.

Stabilization of bottom sediments from Rzeszowski Reservoir

Directory of Open Access Journals (Sweden)

Koś Karolina

2015-06-01

Full Text Available The paper presents results of stabilization of bottom sediments from Rzeszowski Reservoir. Based on the geotechnical characteristics of the tested sediments it was stated they do not fulfill all the criteria set for soils in earth embankments. Therefore, an attempt to improve their parameters was made by using two additives – cement and lime. An unconfined compressive strength, shear strength, bearing ratio and pH reaction were determined on samples after different time of curing. Based on the carried out tests it was stated that the obtained values of unconfined compressive strength of sediments stabilized with cement were relatively low and they did not fulfill the requirements set by the Polish standard, which concerns materials in road engineering. In case of lime stabilization it was stated that the tested sediments with 6% addition of the additive can be used for the bottom layers of the improved road base.

Sediment fingerprinting experiments to test the sensitivity of multivariate mixing models

Science.gov (United States)

Gaspar, Leticia; Blake, Will; Smith, Hugh; Navas, Ana

2014-05-01

Sediment fingerprinting techniques provide insight into the dynamics of sediment transfer processes and support for catchment management decisions. As questions being asked of fingerprinting datasets become increasingly complex, validation of model output and sensitivity tests are increasingly important. This study adopts an experimental approach to explore the validity and sensitivity of mixing model outputs for materials with contrasting geochemical and particle size composition. The experiments reported here focused on (i) the sensitivity of model output to different fingerprint selection procedures and (ii) the influence of source material particle size distributions on model output. Five soils with significantly different geochemistry, soil organic matter and particle size distributions were selected as experimental source materials. A total of twelve sediment mixtures were prepared in the laboratory by combining different quantified proportions of the Kruskal-Wallis test, Discriminant Function Analysis (DFA), Principal Component Analysis (PCA), or correlation matrix). Summary results for the use of the mixing model with the different sets of fingerprint properties for the twelve mixed soils were reasonably consistent with the initial mixing percentages initially known. Given the experimental nature of the work and dry mixing of materials, geochemical conservative behavior was assumed for all elements, even for those that might be disregarded in aquatic systems (e.g. P). In general, the best fits between actual and modeled proportions were found using a set of nine tracer properties (Sr, Rb, Fe, Ti, Ca, Al, P, Si, K, Si) that were derived using DFA coupled with a multivariate stepwise algorithm, with errors between real and estimated value that did not exceed 6.7 % and values of GOF above 94.5 %. The second set of experiments aimed to explore the sensitivity of model output to variability in the particle size of source materials assuming that a degree of

Sediment dynamics in Alpine basins

Science.gov (United States)

Habersack, Helmut; Liébault, Fred; Comiti, Francesco

2017-08-01

In rivers and streams and of the European Alps, sediment transport processes are of great relevance due to their ecological (e.g. aquatic habitats), energy (e.g. reservoir sedimentation) and risk-related (floods and debris flows) consequences. In fact, sediment fluxes are crucial to maintain a good ecological status of watercourses (required by the EU ;Water Framework Directive;, WFD, 2000), as they provide the hydromorphological conditions supporting dynamic aquatic ecosystems (Fryirs and Brierley, 2013; Wohl et al., 2015; Gurnell et al., 2016). Indeed, the key issue to ameliorate river hydrogeomorphological - and thus ecological - status and to comply with WFD provisions lies in allowing the natural processes of sediment and wood supply and transport to take place as much as possible, given the constraints imposed by the non-eliminable uses of each river (Comiti, 2012; Liébault et al., 2013). Specifically river continuity is mentioned in the WFD not only for biota but also sediments, which is hardly discussed in river management so far and almost no concrete measures to improve sediment continuity have been implemented so far (Habersack et al., 2016).

Ecotoxicological assessment of the pharmaceutical compound Triclosan to freshwater invertebrates with emphasis to spiked sediment tests

International Nuclear Information System (INIS)

Pusceddu, Fabio Hermes

2009-01-01

The increasing of Pharmaceutical and Personal Care Products (PPCPs) occurrence in the aquatic environment cause adverse effects on the human health and aquatic communities. The environmental risk of the PPCPs associated with the possibility of synergic effects between PCPPs and the increase of the use of synthetic organic compounds, unchained a great concern on the toxic potential to biota aquatic. Triclosan (5-chloro-2-(2,4-dichlorophenoxy)-phenol) is a pharmaceutical compound widely used due your antibacterial mechanism effect, found in at least 932 products such as shampoos, toilet soaps, deodorants, lotions, toothpaste, detergents, socks and underwear, among others. Currently, studies about the Triclosan toxicity in the water and, mainly in the sediment, are poorly. We have the knowledge that the photodegradation of this product results into dichlorodibenzo-p-dioxin, and now it has great discussion on environmental agencies, like EPA, about the release or restriction of this product. The aim of this work is to assess the effects of Triclosan on mortality of insect larvae Chironomus xanthus and mortality and reproduction inhibition of microcrustacea Ceriodaphnia dubia exposed to Triclosan spiked sediments based on standard methods EPA and OECD. The EC50;96H obtained on acute toxicity tests with C. xanthus was 45,26 mg.Kg -1 . The chronic toxicity tests with C. dubia using spiked sediments were performed following the procedure in Burton and MacPherson (1995). A no-observed-effect concentrations and lowest-observed-effect concentration were 5,78 e 6,94 mg.Kg -1 , respectively. (author)

Using an interlaboratory study to revise methods for conducting 10-d to 42-d water or sediment toxicity tests with Hyalella azteca

Science.gov (United States)

Ivey, Chris D.; Ingersoll, Christopher G.; Brumbaugh, William G.; Hammer, Edward J.; Mount, David R.; Hockett, J. Russell; Norberg-King, Teresa J.; Soucek, Dave; Taylor, Lisa

2016-01-01

Studies have been conducted to refine US Environmental Protection Agency, ASTM International, and Environment Canada standard methods for conducting 42-d reproduction tests with Hyalella azteca in water or in sediment. Modifications to the H. azteca method include better-defined ionic composition requirements for exposure water (i.e., >15 mg/L of chloride and >0.02 mg/L of bromide) and improved survival, growth, and reproduction with alternate diets provided as increased rations over time in water-only or whole-sediment toxicity tests. A total of 24 laboratories volunteered to participate in the present interlaboratory study evaluating the performance of H. azteca in 42-d studies in control sand or control sediment using the refined methods. Improved growth and reproduction of H. azteca was observed with 2 alternate diets of 1) ramped diatoms (Thalassiosira weissflogii) + ramped Tetramin or 2) yeast–cerophyll–trout chow (YCT) + ramped Tetramin, especially when compared with results from the traditional diet of 1.8 mg YCT/d. Laboratories were able to meet proposed test acceptability criteria and in most cases had lower variation in growth or reproduction compared with previous interlaboratory studies using the traditional YCT diet. Laboratory success in conducting 42-d H. azteca exposures benefited from adherence to several key requirements of the detailed testing, culturing, and handling methods. Results from the present interlaboratory study are being used to help revise standard methods for conducting 10-d to 42-d water or sediment toxicity exposures with H. azteca.

Tracing catchment fine sediment sources using the new SIFT (SedIment Fingerprinting Tool) open source software.

Science.gov (United States)

Pulley, S; Collins, A L

2018-09-01

The mitigation of diffuse sediment pollution requires reliable provenance information so that measures can be targeted. Sediment source fingerprinting represents one approach for supporting these needs, but recent methodological developments have resulted in an increasing complexity of data processing methods rendering the approach less accessible to non-specialists. A comprehensive new software programme (SIFT; SedIment Fingerprinting Tool) has therefore been developed which guides the user through critical data analysis decisions and automates all calculations. Multiple source group configurations and composite fingerprints are identified and tested using multiple methods of uncertainty analysis. This aims to explore the sediment provenance information provided by the tracers more comprehensively than a single model, and allows for model configurations with high uncertainties to be rejected. This paper provides an overview of its application to an agricultural catchment in the UK to determine if the approach used can provide a reduction in uncertainty and increase in precision. Five source group classifications were used; three formed using a k-means cluster analysis containing 2, 3 and 4 clusters, and two a-priori groups based upon catchment geology. Three different composite fingerprints were used for each classification and bi-plots, range tests, tracer variability ratios and virtual mixtures tested the reliability of each model configuration. Some model configurations performed poorly when apportioning the composition of virtual mixtures, and different model configurations could produce different sediment provenance results despite using composite fingerprints able to discriminate robustly between the source groups. Despite this uncertainty, dominant sediment sources were identified, and those in close proximity to each sediment sampling location were found to be of greatest importance. This new software, by integrating recent methodological developments in

TBT-contaminated sediments. Treatment in a pilot scale

Energy Technology Data Exchange (ETDEWEB)

Stichnothe, H.; Calmano, W.; Arevalo, E.; Keller, A.; Thoeming, J. [Hamburg Univ. of Technology, Dept. Environmental Science and Technology, Hamburg (Germany)

2005-07-01

Background, aims and scope. Sediments in harbours and nearby shipyards demonstrate widespread contamination with tributyltin (TBT). Therefore, reuse and relocation of dredged material from these locations are prohibited. Even if the international marine organization (IMO) convention concerning TBT-based paints is ratified (champ 2003) the TBT problem in sediments will continue to remain for many years due to the persistence of TBT. Methods. An electrochemical process has been developed to treat polluted sediments. Dredged materials with high and low TBT-contents were studied on a technical and a pilot scale. The treatment process was assessed by chemical analysis and a biotest battery. Additionally, an economic analysis was performed to check the economic feasibility of the process to treat dredged material from two different locations at different operating conditions. Furthermore an up-scaling estimation was performed to evaluate treatment costs at a larger scale, i.e. for a plant having a capacity of 720,000 t/a. Results and discussion. Butyltin species and polycyclic aromatic hydrocarbons (PAH) were decomposed due to electrochemically-induced oxidation, while the treatment did not alter heavy metal and PCB concentrations. The bacteria luminescence test indicated a reduced toxicity after the electrochemical treatment, while the algae growth inhibition test and bacteria contact test did not confirm these results. Based on a small consumer price of Euro 0.12/kWh, treating the high-contaminated sediment in the pilot plant would cost Euro 21/m{sup 3} and Euro 31/m{sup 3} for the low contaminated sediment, respectively. Assuming an industrial consumer price of Euro 0.06/kWh for electricity in an up-scaled process with a capacity of 720,000 t/a, the total treatment costs for the low contaminated sediment would be Euro 13/m{sup 3}. Conclusion. The results of treating dredged material from Bremerhaven and the fine-grained fraction from the METHA plant show that the

Evaluation of suspended sediment concentrations, sediment fluxes and sediment depositions along a reservoir by using laser diffraction and acoustic backscatter data

Science.gov (United States)

Lizano, Laura; Haun, Stefan

2015-04-01

The construction of dams and reservoirs disturb the natural morphological behavior of rivers. A natural settling effect occurs due to the reduced turbulences and flow velocities. As a consequence, reservoirs fill up with sediments which results in a reduction of storage volume, influences the operation of hydropower plants and leads in several cases to flood protection problems. The sediment depositions in reservoirs are standardly evaluated by using bathymetric data, obtained by a single beam sonar from pre-defined cross sections or by an extensive evaluation of the reservoir bed by a side scan sonar. However, a disadvantage of this method is that it is not possible to evaluate the pore water content of the depositions, which may lead as consequence to an uncertainty in the measured amount of deposited sediments. Given that a major part of sediments entering reservoirs are transported in suspension, sediment flux measurements along defined transects could give more reliable information on the settled amount of sediments and additional information on the sediment transport mechanism within the reservoir. An evaluation of the sediment fluxes is in practice often conducted by a single suspended sediment concentration (SSC) measurement in combination with a cross sectional calibration factor to take changes in the SSC along the transect into account. However, these calibration factors are often developed only for one specific in-situ condition and may give unreliable results in case that the boundaries change e.g. the hydraulic conditions. Hence an evaluation of the sediment fluxes along the whole transect would give a more reliable number for the amount of transported sediments through the reservoir. This information can afterwards be used to calculate the amount of settled sediments in different sections of the reservoir and the amount of sediments which will enter the intake. For this study the suspended sediment transport within the Peñas Blancas reservoir in

Determining the sources of fine-grained sediment using the Sediment Source Assessment Tool (Sed_SAT)

Science.gov (United States)

Gorman Sanisaca, Lillian E.; Gellis, Allen C.; Lorenz, David L.

2017-07-27

A sound understanding of sources contributing to instream sediment flux in a watershed is important when developing total maximum daily load (TMDL) management strategies designed to reduce suspended sediment in streams. Sediment fingerprinting and sediment budget approaches are two techniques that, when used jointly, can qualify and quantify the major sources of sediment in a given watershed. The sediment fingerprinting approach uses trace element concentrations from samples in known potential source areas to determine a clear signature of each potential source. A mixing model is then used to determine the relative source contribution to the target suspended sediment samples.The computational steps required to apportion sediment for each target sample are quite involved and time intensive, a problem the Sediment Source Assessment Tool (Sed_SAT) addresses. Sed_SAT is a user-friendly statistical model that guides the user through the necessary steps in order to quantify the relative contributions of sediment sources in a given watershed. The model is written using the statistical software R (R Core Team, 2016b) and utilizes Microsoft Access® as a user interface but requires no prior knowledge of R or Microsoft Access® to successfully run the model successfully. Sed_SAT identifies outliers, corrects for differences in size and organic content in the source samples relative to the target samples, evaluates the conservative behavior of tracers used in fingerprinting by applying a “Bracket Test,” identifies tracers with the highest discriminatory power, and provides robust error analysis through a Monte Carlo simulation following the mixing model. Quantifying sediment source contributions using the sediment fingerprinting approach provides local, State, and Federal land management agencies with important information needed to implement effective strategies to reduce sediment. Sed_SAT is designed to assist these agencies in applying the sediment fingerprinting

Sources of variability in fatty acid (FA) biomarkers in the application of compound-specific stable isotopes (CSSIs) to soil and sediment fingerprinting and tracing: A review

Energy Technology Data Exchange (ETDEWEB)

Reiffarth, D.G., E-mail: Dominic.Reiffarth@unbc.ca [Natural Resources and Environmental Studies Program, University of Northern British Columbia, 3333 University Way, Prince George, BC V2N 4Z9 (Canada); Petticrew, E.L., E-mail: Ellen.Petticrew@unbc.ca [Geography Program and Quesnel River Research Centre, University of Northern British Columbia, 3333 University Way, Prince George, BC V2N 4Z9 (Canada); Owens, P.N., E-mail: Philip.Owens@unbc.ca [Environmental Science Program and Quesnel River Research Centre, University of Northern British Columbia, 3333 University Way, Prince George, BC, V2N 4Z9 (Canada); Lobb, D.A., E-mail: David.Lobb@umanitoba.ca [Watershed Systems Research Program, University of Manitoba, 13 Freedman Crescent, Winnipeg, MB R3T 2N2 (Canada)

2016-09-15

Determining soil redistribution and sediment budgets in watersheds is often challenging. One of the methods for making such determinations employs soil and sediment fingerprinting techniques, using sediment properties such as geochemistry, fallout radionuclides, and mineral magnetism. These methods greatly improve the estimation of erosion and deposition within a watershed, but are limited when determining land use-based soil and sediment movement. Recently, compound-specific stable isotopes (CSSIs), which employ fatty acids naturally occurring in the vegetative cover of soils, offer the possibility of refining fingerprinting techniques based on land use, complementing other methods that are currently in use. The CSSI method has been met with some success; however, challenges still remain with respect to scale and resolution due to a potentially large degree of biological, environmental and analytical uncertainty. By better understanding the source of tracers used in CSSI work and the inherent biochemical variability in those tracers, improvement in sample design and tracer selection is possible. Furthermore, an understanding of environmental and analytical factors affecting the CSSI signal will lead to refinement of the approach and the ability to generate more robust data. This review focuses on sources of biological, environmental and analytical variability in applying CSSI to soil and sediment fingerprinting, and presents recommendations based on past work and current research in this area for improving the CSSI technique. A recommendation, based on current information available in the literature, is to use very-long chain saturated fatty acids and to avoid the use of the ubiquitous saturated fatty acids, C{sub 16} and C{sub 18}. - Highlights: • Compound-specific stable isotopes (CSSIs) of carbon may be used as soil tracers. • The variables affecting CSSI data are: biological, environmental and analytical. • Understanding sources of variability will lead

Sources of variability in fatty acid (FA) biomarkers in the application of compound-specific stable isotopes (CSSIs) to soil and sediment fingerprinting and tracing: A review

International Nuclear Information System (INIS)

Reiffarth, D.G.; Petticrew, E.L.; Owens, P.N.; Lobb, D.A.

2016-01-01

Determining soil redistribution and sediment budgets in watersheds is often challenging. One of the methods for making such determinations employs soil and sediment fingerprinting techniques, using sediment properties such as geochemistry, fallout radionuclides, and mineral magnetism. These methods greatly improve the estimation of erosion and deposition within a watershed, but are limited when determining land use-based soil and sediment movement. Recently, compound-specific stable isotopes (CSSIs), which employ fatty acids naturally occurring in the vegetative cover of soils, offer the possibility of refining fingerprinting techniques based on land use, complementing other methods that are currently in use. The CSSI method has been met with some success; however, challenges still remain with respect to scale and resolution due to a potentially large degree of biological, environmental and analytical uncertainty. By better understanding the source of tracers used in CSSI work and the inherent biochemical variability in those tracers, improvement in sample design and tracer selection is possible. Furthermore, an understanding of environmental and analytical factors affecting the CSSI signal will lead to refinement of the approach and the ability to generate more robust data. This review focuses on sources of biological, environmental and analytical variability in applying CSSI to soil and sediment fingerprinting, and presents recommendations based on past work and current research in this area for improving the CSSI technique. A recommendation, based on current information available in the literature, is to use very-long chain saturated fatty acids and to avoid the use of the ubiquitous saturated fatty acids, C 16 and C 18 . - Highlights: • Compound-specific stable isotopes (CSSIs) of carbon may be used as soil tracers. • The variables affecting CSSI data are: biological, environmental and analytical. • Understanding sources of variability will lead to more

Testing a laser-induced breakdown spectroscopy technique on the Arctic sediments

Science.gov (United States)

Han, D.; Nam, S. I.

2017-12-01

Physical and geochemical investigations coupled with the Laser-induced Breakdown Spectroscopy (LIBS) were performed on three surface sediment cores (ARA03B/24BOX, ARA02B/01(A)MUC, ARA02B/02MUC and ARA02B/03(A)MUC) recovered from the western Arctic Ocean (Chukchi Sea) during IBRV ARON expeditions in 2012. The LIBS technique was applied to carry out elemental chemical analysis of the Arctic sediments and compared with that measured by ITRAX X-ray fuorescence (XRF) core scanning. LIBS and XRF have shown similar elemental composition within each sediment core. In this study, mineral composition (XRD), grain size distribution and organic carbon content as well as elemental composition (LIBS) were all considered to understand paleoenvironmental changes (ocean circulation, sea-ice drift, iceberg discharge, and etc.) recorded in the Arctic Holocene sediment. Quantitative LIBS analysis shows a gradually varying distribution of the elements along the sampled core and clear separation between the cores. The cores are geochemically characterized by elevated Mn profile. The gradient of mineral composition and grain sizes among the cores shows regional distribution and variation in sedimentary condition due to geological distance between East Siberian and North America. The present study reveals that a LIBS technique can be employed for in-situ sediment analyses for the Arctic Ocean. Furthermore, LIBS does not require costly equipment, trained operators, and complicated sample pre-treatment processes compared to Atomic absorption spectroscopy (AAS) and inductively coupled plasma emission spectroscopy (ICP), and also known to show relatively high levels of sensitivity, precision, and distinction than XRF analysis, scanning electron microscopy-energy dispersive spectrometry (SEM-EDS), and electron probe X-ray microanalysis (EPMA).

Combining caesium-137 measurements and suspended sediment load data to investigate the sediment response of a small catchment in southern Italy

Directory of Open Access Journals (Sweden)

P. Porto

2015-03-01

Full Text Available A long-term measurement programme was operated in southern Italy during the 1960s and 1970s, to provide information on the suspended sediment yields from the main river basins. Information obtained for the rivers of Calabria suggests that suspended sediment yields in this area are relatively low. However, there is evidence that the intensity of land degradation within the upstream catchments is substantially higher than suggested by the values of specific sediment yield and there is a need to explore the relationship between on-site soil loss and downstream sediment yield more closely. Monitoring time-integrated erosion rates over large areas has traditionally required extensive long-term measurement programmes employing experimental plots. The fallout radionuclide caesium-137 (137Cs offers an alternative means of documenting medium-term rates of soil loss. This paper describes the use of 137Cs measurements and the available sediment load data to explore the links between soil erosion, sediment redistribution and storage, and sediment output for a medium-scale (41.3 km2 catchment in Calabria. Data available from a sediment load monitoring programme undertaken at the catchment outlet during 1962–1977 have been used to estimate the longer-term catchment sediment yield. This estimate has been combined with information provided by the 137Cs measurements, to establish a medium-term sediment budget for the catchment. The results provided by the 137Cs measurements indicate that the catchment is subject to much higher rates of soil loss and land degradation than suggested by its specific sediment yield. These findings are consistent with the results obtained for other catchments in Calabria for which both 137Cs derived erosion rates and measured sediment yields are available.

Composite fingerprinting of suspended-sediments in Sorsogon , Philippines

International Nuclear Information System (INIS)

Ramirez, J.D.; Sta Maria, E.J.; Madrid, J.F.; Asa, A.D.D.; Aniago, R.J.; Bulos, A.D.; Zombrito, E.Z.

2015-01-01

Sediment-related environmental problems pose a threat not only in land management sustainability but also in management of aquatic ecosystem. Sediments often serve as sinks of nutrients and contaminants that regularly recharge overlying waters and could trigger harmful algal blooms (HAB) together with unfavorable environment conditions. One HAB affected area in the southernmost tip of Luzon, Philippines is Sorsogon Bay. In Sorsogon Bay, the harvest and consumption ban was declared for several years due to the level of toxins in shellfish which exceeded the regulatory limit. Identification of sediment sources is useful tool in planning effective sediment management strategies. A method to determine possible sources of sediment-associated nutrients is sediment fingerprinting. It characterizes land-based sediment sources to derive estimates of the portions of suspended sediment originating from discrete upstream source areas. There are wide ranges of diagnostic properties which can be possible fingerprints such as mineralogic, mineral-magnetic, geochemical, organic, isotopic, physical and radiometric parameters. This study investigates on potential source of sediments from Sampaloc River using different chemical, radiometric and isotopic parameters, Range test and Kruskal-Wallis H-test were employed and indicated that the calcium, titanium, δ”1”3C signal, and to tal carbon content are possible fingerprint parameters that will identify the sources of sediments. Results of a mathematical mixing model showed that channel banks (81.0%) are the largest sediment load contributors in Sampaloc River, followed by cultivated areas (15.5%) and woodlands (3.5%). (author)

Characteristics of phosphorus adsorption by sediment mineral matrices with different particle sizes

Directory of Open Access Journals (Sweden)

Yang Xiao

2013-07-01

Full Text Available The particle size of sediment is one of the main factors that influence the phosphorus physical adsorption on sediment. In order to eliminate the effect of other components of sediment on the phosphorus physical adsorption the sediment mineral matrices were obtained by removing inorganic matter metal oxides, and organic matter from natural sediments, which were collected from the Nantong reach of the Yangtze River. The results show that an exponential relationship exists between the median particle size (D50 and specific surface area (Sg of the sediment mineral matrices, and the fine sediment mineral matrix sample has a larger specific surface area and pore volume than the coarse sediment particles. The kinetic equations were used to describe the phosphorus adsorption process of the sediment mineral matrices, including the Elovich equation, quasi-first-order adsorption kinetic equation, and quasi-second-order adsorption kinetic equation. The results show that the quasi-second-order adsorption kinetic equation has the best fitting effect. Using the mass conservation and Langmuir adsorption kinetic equations, a formula was deduced to calculate the equilibrium adsorption capacity of the sediment mineral matrices. The results of this study show that the phosphorus adsorption capacity decreases with the increase of D50, indicating that the specific surface area and pore volume are the main factors in determining the phosphorus adsorption capacity of the sediment mineral matrices. This study will help understand the important role of sediment in the transformation of phosphorus in aquatic environments.

Efficient Noninferiority Testing Procedures for Simultaneously Assessing Sensitivity and Specificity of Two Diagnostic Tests

Directory of Open Access Journals (Sweden)

Guogen Shan

2015-01-01

Full Text Available Sensitivity and specificity are often used to assess the performance of a diagnostic test with binary outcomes. Wald-type test statistics have been proposed for testing sensitivity and specificity individually. In the presence of a gold standard, simultaneous comparison between two diagnostic tests for noninferiority of sensitivity and specificity based on an asymptotic approach has been studied by Chen et al. (2003. However, the asymptotic approach may suffer from unsatisfactory type I error control as observed from many studies, especially in small to medium sample settings. In this paper, we compare three unconditional approaches for simultaneously testing sensitivity and specificity. They are approaches based on estimation, maximization, and a combination of estimation and maximization. Although the estimation approach does not guarantee type I error, it has satisfactory performance with regard to type I error control. The other two unconditional approaches are exact. The approach based on estimation and maximization is generally more powerful than the approach based on maximization.

Sensitivity and Specificity of Clinical and Laboratory Otolith Function Tests.

Science.gov (United States)

Kumar, Lokesh; Thakar, Alok; Thakur, Bhaskar; Sikka, Kapil

2017-10-01

To evaluate clinic based and laboratory tests of otolith function for their sensitivity and specificity in demarcating unilateral compensated complete vestibular deficit from normal. Prospective cross-sectional study. Tertiary care hospital vestibular physiology laboratory. Control group-30 healthy adults, 20-45 years age; Case group-15 subjects post vestibular shwannoma excision or post-labyrinthectomy with compensated unilateral complete audio-vestibular loss. Otolith function evaluation by precise clinical testing (head tilt test-HTT; subjective visual vertical-SVV) and laboratory testing (headroll-eye counterroll-HR-ECR; vesibular evoked myogenic potentials-cVEMP). Sensitivity and specificity of clinical and laboratory tests in differentiating case and control subjects. Measurable test results were universally obtained with clinical otolith tests (SVV; HTT) but not with laboratory tests. The HR-ECR test did not indicate any definitive wave forms in 10% controls and 26% cases. cVEMP responses were absent in 10% controls.HTT test with normative cutoff at 2 degrees deviations from vertical noted as 93.33% sensitive and 100% specific. SVV test with normative cutoff at 1.3 degrees noted as 100% sensitive and 100% specific. Laboratory tests demonstrated poorer specificities owing primarily to significant unresponsiveness in normal controls. Clinical otolith function tests, if conducted with precision, demonstrate greater ability than laboratory testing in discriminating normal controls from cases with unilateral complete compensated vestibular dysfunction.

Mathematical simulation of sediment and radionuclide transport in estuaries

International Nuclear Information System (INIS)

Onishi, Y.; Trent, D.S.

1982-11-01

The finite element model LFESCOT (Flow, Energy, Salinity, Sediment and Contaminant Transport Model) was synthesized under this study to simulate radionuclide transport in estuaries to obtain accurate radionuclide distributions which are affected by these factors: time variance, three-dimensional flow, temperature, salinity, and sediments. Because sediment transport and radionuclide adsorption/desorption depend strongly on sizes or types of sediments, FLESCOT simulates sediment and a sediment-sorbed radionuclide for the total of three sediment-size fractions (or sediment types) of both cohesive and noncohesive sediments. It also calculates changes of estuarine bed conditions, including bed elevation changes due to sediment erosion/deposition, and three-dimensional distributions of three bed sediment sizes and sediment-sorbed radionuclides within the bed. Although the model was synthesized for radionuclide transport, it is general enough to also handle other contaminants such as heavy metals, pesticides, or toxic chemicals. The model was checked for its capability for flow, water surface elevation change, salinity, sediment and radionuclide transport under various simple conditions first, confirming the general validity of the model's computational schemes. These tests also revealed that FLESCOT can use large aspect ratios of computational cells, which are necessary in handling long estuarine study areas. After these simple tests, FLESCOT was applied to the Hudson River estuary between Chelsea and the mouth of the river to examine how well the model can predict radionuclide transport through simulating tidally influenced three-dimensional flow, salinity, sediment and radionuclide movements with their interactions

A method for developing a large-scale sediment yield index for European river basins

Energy Technology Data Exchange (ETDEWEB)

Delmas, Magalie; Cerdan, Olivier; Garcin, Manuel [BRGM ARN/ESL, Orleans (France); Mouchel, Jean-Marie [UMR Sisyphe, Univ. P and M Curie, Paris (France)

2009-12-15

Background, aim, and scope: Sediment fluxes within continental areas play a major role in biogeochemical cycles and are often the cause of soil surface degradation as well as water and ecosystem pollution. In a situation where a high proportion of the land surface is experiencing significant global land use and climate changes, it appears important to establish sediment budgets considering the major processes forcing sediment redistribution within drainage areas. In this context, the aim of this study is to test a methodology to estimate a sediment yield index at a large spatial resolution for European river basins. Data and methods: Four indicators representing processes respectively considered as sources (mass movement and hillslope erosion), sinks (deposits), and transfers of sediments (drainage density) are defined using distributed data. Using these indicators we propose a basic conceptual approach to test the possibility of explaining sediment yield observed at the outlet of 29 selected European river basins. We propose an index which adds the two sources and transfers, and subsequently subtracts the sink term. This index is then compared to observed sediment yield data. Results: With this approach, variability between river basins is observed and the evolution of each indicator analyzed. A linear regression shows a correlation coefficient of 0.83 linking observed specific sediment yield (SSY) with the SSY index. Discussion: To improve this approach at this large river basin scale, basin classification is further refined using the relation between the observed SSY and the index obtained from the four indicators. It allows a refinement of the results. Conclusions: This study presents a conceptual approach offering the advantages of using spatially distributed data combined with major sediment redistribution processes to estimate the sediment yield observed at the outlet of river basins. Recommendations and perspectives: Inclusion of better information on

Quantifying Construction Site Sediment Discharge Risk and Treatment Potential

Science.gov (United States)

Ferrell, L.; Beighley, R. E.

2006-12-01

Dealing with soil erosion and sediment transport can be a significant challenge during the construction process due to the potentially large spatial and temporal extent and conditions of bare soils. Best Management Practices (BMP) are commonly used to eliminate or reduce offsite discharge of sediment. However, few efforts have investigated the time varying risk of sediment discharge from construction sites, which often have dynamic soil conditions and the potential for less than optimal BMP installations. The goal of this research is to improve the design, implementation and effectiveness of sediment and erosion control at construction sites using site specific, temporal distributions of sediment discharge risk. Sediment risk is determined from individual factors leading to sediment expert, such as rainfall frequency, the adequacy of BMP installations, and the extent and duration of bare soil conditions. This research specifically focuses on quantifying: (a) the effectiveness of temporary sediment and control erosion control BMPs in preventing, containing, and/or treating construction site sediment discharge at varying levels of "proper" installation, and (b) sediment discharge potential from construction sites during different phases of construction, (ex., disturbed earth operations). BMPs are evaluated at selected construction sites in southern California and at the Soil Erosion Research Laboratory (SERL) in the Civil and Environmental Engineering department at San Diego State University. SERL experiments are performed on a 3-m by 10-m tilting soil bed with soil depths up to 1 meter, slopes ranging from 0 to 50 percent, and rainfall rates up to 150 mm/hr (6 in/hr). BMP performance is assessed based on experiments where BMPs are installed per manufacture specifications, potential less than optimal installations, and no treatment conditions. Soil conditions are also varied to represent site conditions during different phases of construction (i.e., loose lifts

Contamination of Detained Sediment in Sustainable Urban Drainage Systems

Directory of Open Access Journals (Sweden)

Deonie Allen

2017-05-01

Full Text Available Adsorption is a key water pollution remediation measure used to achieve stormwater quality improvement in Sustainable urban Drainage Systems (SuDS. The level of contamination of detained sediment within SuDS assets is not well documented, with published investigations limited to specific contaminant occurrence in ponds, wetlands or infiltration devices (bioretention cells and generally focused on solute or suspended sediment. Guidance on contamination threshold levels and potential deposited sediment contamination information is not included in current UK SuDS design or maintenance guidance, primarily due to a lack of evidence and understanding. There is a need to understand possible deposited sediment contamination levels in SuDS, specifically in relation to sediment removal maintenance activities and potential impact on receiving waterways of conveyed sediment. Thus, the objective of the research presented herein was to identify what major elements and trace metals were observable in (the investigated SuDS assets detained sediment, the concentration of these major elements and trace metals and whether they met/surpassed ecotoxicity or contaminated land thresholds. The research presented here provides evidence of investigated SuDS sediment major element and trace metal levels to help inform guidance and maintenance needs, and presents a new methodology to identify the general cause (anthropocentric land use and extent of detained SuDS fine urban sediment contamination through use of a contamination matrix.

Phase Startup Initiative Phases 3 and 4 Test Plan and Test Specification ( OCRWM)

Energy Technology Data Exchange (ETDEWEB)

PAJUNEN, A.L.; LANGEVIN, M.J.

2000-08-07

Construction for the Spent Nuclear Fuel (SNF) Project facilities is continuing per the Level III Baseline Schedule, and installation of the Fuel Retrieval System (FRS) and Integrated Water Treatment System (IWTS) in K West Basin is now complete. In order to accelerate the project, a phased start up strategy to initiate testing of the FRS and IWTS early in the overall project schedule was proposed (Williams 1999). Wilkinson (1999) expands the definition of the original proposal into four functional testing phases of the Phased Startup Initiative (PSI). Phases 1 and 2 are based on performing functional tests using dummy fuel. This test plan provides overall guidance for Phase 3 and 4 tests, which are performed using actual irradiated N fuel assemblies. The overall objective of the Phase 3 and 4 testing is to verify how the FRS and IWTS respond while processing actual fuel. Conducting these tests early in the project schedule will allow identification and resolution of equipment and process problems before they become activities on the start-up critical path. The specific objectives of this test plan are to: Define the Phase 3 and 4 test scope for the FRS and IWTS; Provide detailed test requirements that can be used to write the specific test procedures; Define data required and measurements to be taken. Where existing methods to obtain these do not exist, enough detail will be provided to define required additional equipment; and Define specific test objectives and acceptance criteria.

Phase Startup Initiative Phases 3 and 4 Test Plan and Test Specification (OCRWM)

International Nuclear Information System (INIS)

PAJUNEN, A.L.; LANGEVIN, M.J.

2000-01-01

Construction for the Spent Nuclear Fuel (SNF) Project facilities is continuing per the Level III Baseline Schedule, and installation of the Fuel Retrieval System (FRS) and Integrated Water Treatment System (IWTS) in K West Basin is now complete. In order to accelerate the project, a phased start up strategy to initiate testing of the FRS and IWTS early in the overall project schedule was proposed (Williams 1999). Wilkinson (1999) expands the definition of the original proposal into four functional testing phases of the Phased Startup Initiative (PSI). Phases 1 and 2 are based on performing functional tests using dummy fuel. This test plan provides overall guidance for Phase 3 and 4 tests, which are performed using actual irradiated N fuel assemblies. The overall objective of the Phase 3 and 4 testing is to verify how the FRS and IWTS respond while processing actual fuel. Conducting these tests early in the project schedule will allow identification and resolution of equipment and process problems before they become activities on the start-up critical path. The specific objectives of this test plan are to: Define the Phase 3 and 4 test scope for the FRS and IWTS; Provide detailed test requirements that can be used to write the specific test procedures; Define data required and measurements to be taken. Where existing methods to obtain these do not exist, enough detail will be provided to define required additional equipment; and Define specific test objectives and acceptance criteria

What is the pollution status of North Sea sediments?

International Nuclear Information System (INIS)

Chapman, P.M.; Heip, C.; Cofino, W.

1993-01-01

A March 1990 international sea-going workshop in Bremerhaven, Germany provided the opportunity to conduct detailed sediment toxicity testing in concert with studies of fish histopathology, bioaccumulation, benthic community structure, and sediment chemical contamination in the North Sea. Two gradients of sediment chemical contamination were tested, one from an abandoned oil platform and the other from the mouth of the Elbe River northward to the Dogger Bank. Using a preponderance of evidence approach, it was determined that sediments nearest the Elbe are moderately polluted (pollution is defined as contamination, toxicity, and community alteration) and that sediments offshore and at the Dogger Bank are unpolluted. Sediments nearest the oil platform showed evidence for a low level of pollution, but there was no evidence of pollution 125 m from the platform. The results suggest the testable hypothesis that North Sea sediments away from point sources of pollution such as coastal areas and drilling platforms are presently not polluted. 46 refs., 2 figs., 6 tabs

Conceptualizing the role of sediment in sustaining ecosystem services: Sediment-ecosystem regional assessment (SEcoRA).

Science.gov (United States)

Apitz, Sabine E

2012-01-15

There is a growing trend to include a consideration of ecosystem services, the benefits that people obtain from ecosystems, within decision frameworks. Not more than a decade ago, sediment management efforts were largely site-specific and held little attention except in terms of managing contaminant inputs and addressing sediments as a nuisance at commercial ports and harbors. Sediments figure extensively in the Millennium Ecosystem Assessment; however, contaminated sediment is not the dominant concern. Rather, the focus is on land and water use and management on the landscape scale, which can profoundly affect soil and sediment quality, quantity and fate. Habitat change and loss, due to changes in sediment inputs, whether reductions (resulting in the loss of beaches, storm protection, nutrient inputs, etc.) or increases (resulting in lake, reservoir and wetland infilling, coral reef smothering, etc.); eutrophication and reductions in nutrient inputs, and disturbance due to development and fishing practices are considered major drivers, with significant consequences for biodiversity and the provision and resilience of ecosystem functions and services. As a mobile connecting medium between various parts of the ecosystem via the hydrocycle, sediments both contaminated and uncontaminated, play both positive and negative roles in the viability and sustainability of social, economic, and ecological objectives. How these roles are interpreted depends upon whether sediment status (defined in terms of sediment quality, quantity, location and transport) is appropriate to the needs of a given endpoint; understanding and managing the dynamic interactions of sediment status on a diverse range of endpoints at the landscape or watershed scale should be the focus of sediment management. This paper seeks to provide a language and conceptual framework upon which sediment-ecosystem regional assessments (SEcoRAs) can be developed in support of that goal. Copyright © 2011 Elsevier B

Wood and Sediment Dynamics in River Corridors

Science.gov (United States)

Wohl, E.; Scott, D.

2015-12-01

Large wood along rivers influences entrainment, transport, and storage of mineral sediment and particulate organic matter. We review how wood alters sediment dynamics and explore patterns among volumes of instream wood, sediment storage, and residual pools for dispersed pieces of wood, logjams, and beaver dams. We hypothesized that: volume of sediment per unit area of channel stored in association with wood is inversely proportional to drainage area; the form of sediment storage changes downstream; sediment storage correlates most strongly with wood load; and volume of sediment stored behind beaver dams correlates with pond area. Lack of data from larger drainage areas limits tests of these hypotheses, but analyses suggest a negative correlation between sediment volume and drainage area and a positive correlation between wood and sediment volume. The form of sediment storage in relation to wood changes downstream, with wedges of sediment upstream from jammed steps most prevalent in small, steep channels and more dispersed sediment storage in lower gradient channels. Use of a published relation between sediment volume, channel width, and gradient predicted about half of the variation in sediment stored upstream from jammed steps. Sediment volume correlates well with beaver pond area. Historically more abundant instream wood and beaver populations likely equated to greater sediment storage within river corridors. This review of the existing literature on wood and sediment dynamics highlights the lack of studies on larger rivers.

Templates for Cross-Cultural and Culturally Specific Usability Testing

DEFF Research Database (Denmark)

Clemmensen, Torkil

2011-01-01

The cultural diversity of users of technology challenges our methods for usability testing. This article suggests templates for cross-culturally and culturally specific usability testing, based on studies of usability testing in companies in Mumbai, Beijing, and Copenhagen. Study 1 was a cross...... tests. The result was the construction of templates for usability testing. The culturally specific templates were in Mumbai “user-centered evaluation,” Copenhagen “client-centered evaluation,” and Beijing “evaluator-centered evaluation.” The findings are compared with related research...

Testing a two-scale focused conservation strategy for reducing phosphorus and sediment loads from agricultural watersheds

Science.gov (United States)

Carvin, Rebecca; Good, Laura W.; Fitzpatrick, Faith A.; Diehl, Curt; Songer, Katherine; Meyer, Kimberly J.; Panuska, John C.; Richter, Steve; Whalley, Kyle

2018-01-01

This study tested a focused strategy for reducing phosphorus (P) and sediment loads in agricultural streams. The strategy involved selecting small watersheds identified as likely to respond relatively quickly, and then focusing conservation practices on high-contributing fields within those watersheds. Two 5,000 ha (12,360 ac) watersheds in the Driftless Area of south central Wisconsin, previously ranked in the top 6% of similarly sized Wisconsin watersheds for expected responsiveness to conservation efforts to reduce high P and sediment loads, were chosen for the study. The stream outlets from both watersheds were monitored from October of 2006 through September of 2016 for streamflow and concentrations of sediment, total P, and, beginning in October of 2009, total dissolved P. Fields and pastures having the highest potential P delivery to the streams in each watershed were identified using the Wisconsin P Index (Good et al. 2012). After three years of baseline monitoring (2006 to 2009), farmers implemented both field- and farm-based conservation practices in one watershed (treatment) as a means to reduce sediment and P inputs to the stream from the highest contributing areas, whereas there were no out-of-the-ordinary conservation efforts in the second watershed (control). Implementation occurred primarily in 2011 and 2012. In the four years following implementation of conservation practices (2013 through 2016), there was a statistically significant reduction in storm-event suspended sediment loads in the treatment watershed compared to the control watershed when the ground was not frozen (p = 0.047). While there was an apparent reduction in year-round suspended sediment event loads, it was not statistically significant at the 95% confidence level (p = 0.15). Total P loads were significantly reduced for runoff events (p < 0.01) with a median reduction of 50%. Total P and total dissolved P concentrations for low-flow conditions were also significantly reduced (p

Phased Startup Initiative Phases 3 and 4 Test Plan and Test Specification (OCRWM)

International Nuclear Information System (INIS)

PITNER, A.L.

2000-01-01

Construction for the Spent Nuclear Fuel (SNF) Project facilities is continuing per the Level III Baseline Schedule, and installation of the Fuel Retrieval System (FRS) and Integrated Water Treatment System (IWTS) in K West Basin is now complete. In order to accelerate the project, a phased start up strategy to initiate testing of the FRS and IWTS early in the overall project schedule was proposed (Williams 1999). Wilkinson (1999) expands the definition of the original proposal into four functional testing phases of the Phased Startup Initiative (PSI). Phases 1 and 2 are based on performing functional tests using dummy fuel. These tests are described in separate planning documents. This test plan provides overall guidance for Phase 3 and 4 tests, which are performed using actual irradiated N fuel assemblies. The overall objective of the Phase 3 and 4 testing is to verify how the FRS and IWTS respond while processing actual fuel. Conducting these tests early in the project schedule will allow identification and resolution of equipment and process problems before they become activities on the start-up critical path. The specific objectives of this test plan are to: (1) Define the test scope for the FRS and IWTS; (2) Provide detailed test requirements that can be used to write the specific test procedures; (3) Define data required and measurements to be taken. Where existing methods to obtain these do not exist, enough detail will be provided to define required additional equipment; and (4) Define specific test objectives and acceptance criteria

The use of ecocores to evaluate biodegradation in marine sediments

DEFF Research Database (Denmark)

Jensen, Kurt; Albrechtsen, Hans-Jørgen; Nielsen, Jef

1988-01-01

A laboratory sediment microcosm called the ecocore is described. It has been used to test the biodegradability of substances which predominantly enter the sediment. A new method for introducing hydrophobic test substances such as hydrocarbons to the test system is also described. In a series...

Low specificity of 2 tetanus rapid tests in Cambodia.

Science.gov (United States)

Schlumberger, M; Yvonnet, B; Lesage, G; Tep, B

2015-01-01

Rapid testing for tetanus on serum or blood allows for an immediate evaluation of individual protection against tetanus in developed countries, using a "single step" immunochromatographic technique using tetanus toxoid. The specificity of these tests, compared to the reference method for tetanus, mouse serum neutralization testing, has however never been assessed in these countries, due to the difficulty to perform serum neutralization titration in mice, because of animal testing bioethical regulations. A collection of sera from adult volunteers in Cambodia, living in rural environment, was tested for tetanus antibodies by ELISA in France, and by mouse serum neutralization in Vietnam. This allowed estimating the sensitivity and specificity of 2 rapid tetanus tests, available on the market: TQS™ and Tetanotop™. The sensitivity of these tests was adequate, compared to mice serum neutralization test, for a test threshold of 0.01 IU/mL, (100% for TQS™, 91% for Tetanotop™), but their specificity was very low (1% for TQS™ and 13% for Tetanotop™). The results prove that these rapid tests for the assessment of individual protection against tetanus should not be used in the adult rural Cambodian population. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

MORPHOLOGY OF METHANE HYDRATE HOST SEDIMENTS

International Nuclear Information System (INIS)

JONES, K.W.; FENG, H.; TOMOV, S.; WINTER, W.J.; EATON, M.; MAHAJAN, D.

2004-01-01

Results from simulated experiments in several laboratories show that host sediments influence hydrate formation in accord with known heterogeneity of host sediments at sites of gas hydrate occurrence (1). For example, in Mackenzie Delta, NWT Canada (Mallik 2L-38 well), coarser-grained units (pore-filling model) are found whereas in the Gulf of Mexico, the found hydrate samples do not appear to be lithologically controlled. We have initiated a systematic study of sediments, initially focusing on samples from various depths at a specific site, to establish a correlation with hydrate occurrence (or variations thereof) to establish differences in their microstructure, porosity, and other associated properties. The synchrotron computed microtomography (CMT) set-up at the X-27A tomography beam line at the National Synchrotron Light Source (NSLS), Brookhaven National Laboratory was used as a tool to study sediments from Blake Ridge at three sub bottom depths of 0.2, 50, and 667 meters. Results from the tomographic analysis of the deepest sample (667 m) are presented here to illustrate how tomography can be used to obtain new insights into the structures of methane hydrate host sediments. The investigation shows the internal grain/pore space resolution in the microstructure and a 3-D visualization of the connecting pathways obtained following data segmentation into pore space and grains within the sediment sample. The analysis gives the sample porosity, specific surface area, mean particle size, and tortuosity, as well. An earlier report on the experimental program has been given by Mahajan et al. (2)

Assessing the effects of fluoxetine on Physa acuta (Gastropoda, Pulmonata) and Chironomus riparius (Insecta, Diptera) using a two-species water-sediment test

Energy Technology Data Exchange (ETDEWEB)

Sanchez-Argueello, Paloma [Laboratory for Ecotoxicology, Department of the Environment, INIA, Crta, A Coruna km 7, 28040 Madrid (Spain)], E-mail: arguello@inia.es; Fernandez, Carlos; Tarazona, Jose V. [Laboratory for Ecotoxicology, Department of the Environment, INIA, Crta, A Coruna km 7, 28040 Madrid (Spain)

2009-03-01

Fluoxetine has been tested in a two-species water-sediment system, which allowed a two-generation study with Chironomus riparius and a partial life-cycle with the freshwater snail Physa acuta to be performed at the same time. The design considered the continuous application of fluoxetine to overlaying water for nominal concentrations of 31.25, 62.5, 125 and 250 {mu}g/L. A fifth treatment (87.5 {mu}g/L) level consisted of pulse applications once a week. Measures of water and sediment concentrations were determined once a week and at the end of experiment (day 44), respectively. The fate study demonstrated that water dissipation can be explained by partitioning of fluoxetine to sediment. At the end of experiment, the percentage of detected fluoxetine was up to 10-fold higher in sediment than in overlaying water. The employed two-species test allowed distinguishing, in the same exposure conditions, effects due to waterborne exposure together ingestion at the sediment surface (freshwater grazing snail P. acuta) and exposure by burrowing activities (sediment-dwelling insect larvae C. riparius). The effect assessment showed a stimulation of P. acuta reproduction at lower concentrations (31.25 and 62.5 {mu}g/L), while the opposite effect was observed at the highest treatment (250 {mu}g/L). Additional studies should be conducted to establish if the statistically significant differences observed in F0 sex ratio at the 62.5 {mu}g/L and F1 adult emergence at 31.25 {mu}g/L of C. riparius have a toxicological significance. This study showed that fluoxetine can affect reproduction of freshwater molluscs. The results of the present study may contribute to knowledge on ecotoxicology of pharmaceuticals, about which little data is available. The possible consequences and implications for targeting the environmental risk assessment of fluoxetine are discussed.

Assessing the effects of fluoxetine on Physa acuta (Gastropoda, Pulmonata) and Chironomus riparius (Insecta, Diptera) using a two-species water-sediment test

International Nuclear Information System (INIS)

Sanchez-Argueello, Paloma; Fernandez, Carlos; Tarazona, Jose V.

2009-01-01

Fluoxetine has been tested in a two-species water-sediment system, which allowed a two-generation study with Chironomus riparius and a partial life-cycle with the freshwater snail Physa acuta to be performed at the same time. The design considered the continuous application of fluoxetine to overlaying water for nominal concentrations of 31.25, 62.5, 125 and 250 μg/L. A fifth treatment (87.5 μg/L) level consisted of pulse applications once a week. Measures of water and sediment concentrations were determined once a week and at the end of experiment (day 44), respectively. The fate study demonstrated that water dissipation can be explained by partitioning of fluoxetine to sediment. At the end of experiment, the percentage of detected fluoxetine was up to 10-fold higher in sediment than in overlaying water. The employed two-species test allowed distinguishing, in the same exposure conditions, effects due to waterborne exposure together ingestion at the sediment surface (freshwater grazing snail P. acuta) and exposure by burrowing activities (sediment-dwelling insect larvae C. riparius). The effect assessment showed a stimulation of P. acuta reproduction at lower concentrations (31.25 and 62.5 μg/L), while the opposite effect was observed at the highest treatment (250 μg/L). Additional studies should be conducted to establish if the statistically significant differences observed in F0 sex ratio at the 62.5 μg/L and F1 adult emergence at 31.25 μg/L of C. riparius have a toxicological significance. This study showed that fluoxetine can affect reproduction of freshwater molluscs. The results of the present study may contribute to knowledge on ecotoxicology of pharmaceuticals, about which little data is available. The possible consequences and implications for targeting the environmental risk assessment of fluoxetine are discussed

Deliverable 3.3.2 Specification of tests and test groups

DEFF Research Database (Denmark)

Peterson, Carrie Beth; Mitseva, Anelia; Harpur, Jill

2009-01-01

Deliverable 3.3.2: Specification of tests and test groups One of the main goals of the ISISEMD project is to offer innovative ICT services to improve the quality of life of elderly persons with cognitive problems or mild dementia and their informal and formal caregivers who provide every day care...... for them. This will be done via integrating intelligent scalable ICT services which will be tested for a period of 12 months under realistic conditions. Offering the services could not be complete without evaluating quality of life improvement, user acceptance and user satisfaction with a representative...... group of the target user groups. This document is devoted to describing important aspects of services evaluation such as: who the test participants will be, inclusion and exclusion criterion, selection standards, how the test participants will be recruited, ethical considerations, etc. Test methodology...

Contemporary sediment-transport processes in submarine canyons.

Science.gov (United States)

Puig, Pere; Palanques, Albert; Martín, Jacobo

2014-01-01

Submarine canyons are morphological incisions into continental margins that act as major conduits of sediment from shallow- to deep-sea regions. However, the exact mechanisms involved in sediment transfer within submarine canyons are still a subject of investigation. Several studies have provided direct information about contemporary sedimentary processes in submarine canyons that suggests different modes of transport and various triggering mechanisms. Storm-induced turbidity currents and enhanced off-shelf advection, hyperpycnal flows and failures of recently deposited fluvial sediments, dense shelf-water cascading, canyon-flank failures, and trawling-induced resuspension largely dominate present-day sediment transfer through canyons. Additionally, internal waves periodically resuspend ephemeral deposits within canyons and contribute to dispersing particles or retaining and accumulating them in specific regions. These transport processes commonly deposit sediments in the upper- and middle-canyon reaches for decades or centuries before being completely or partially flushed farther down-canyon by large sediment failures.

Bacterial niche-specific genome expansion is coupled with highly frequent gene disruptions in deep-sea sediments

KAUST Repository

Wang, Yong; Yang, Jiang Ke; Lee, On On; Li, Tie Gang; Al-Suwailem, Abdulaziz M.; Danchin, Antoine; Qian, Pei-Yuan

2011-01-01

The complexity and dynamics of microbial metagenomes may be evaluated by genome size, gene duplication and the disruption rate between lineages. In this study, we pyrosequenced the metagenomes of microbes obtained from the brine and sediment of a deep-sea brine pool in the Red Sea to explore the possible genomic adaptations of the microbes in response to environmental changes. The microbes from the brine and sediments (both surface and deep layers) of the Atlantis II Deep brine pool had similar communities whereas the effective genome size varied from 7.4 Mb in the brine to more than 9 Mb in the sediment. This genome expansion in the sediment samples was due to gene duplication as evidenced by enrichment of the homologs. The duplicated genes were highly disrupted, on average by 47.6% and 70% for the surface and deep layers of the Atlantis II Deep sediment samples, respectively. The disruptive effects appeared to be mainly due to point mutations and frameshifts. In contrast, the homologs from the Atlantis II Deep brine sample were highly conserved and they maintained relatively small copy numbers. Likely, the adaptation of the microbes in the sediments was coupled with pseudogenizations and possibly functional diversifications of the paralogs in the expanded genomes. The maintenance of the pseudogenes in the large genomes is discussed. © 2011 Wang et al.

Bacterial niche-specific genome expansion is coupled with highly frequent gene disruptions in deep-sea sediments

KAUST Repository

Wang, Yong

2011-12-21

The complexity and dynamics of microbial metagenomes may be evaluated by genome size, gene duplication and the disruption rate between lineages. In this study, we pyrosequenced the metagenomes of microbes obtained from the brine and sediment of a deep-sea brine pool in the Red Sea to explore the possible genomic adaptations of the microbes in response to environmental changes. The microbes from the brine and sediments (both surface and deep layers) of the Atlantis II Deep brine pool had similar communities whereas the effective genome size varied from 7.4 Mb in the brine to more than 9 Mb in the sediment. This genome expansion in the sediment samples was due to gene duplication as evidenced by enrichment of the homologs. The duplicated genes were highly disrupted, on average by 47.6% and 70% for the surface and deep layers of the Atlantis II Deep sediment samples, respectively. The disruptive effects appeared to be mainly due to point mutations and frameshifts. In contrast, the homologs from the Atlantis II Deep brine sample were highly conserved and they maintained relatively small copy numbers. Likely, the adaptation of the microbes in the sediments was coupled with pseudogenizations and possibly functional diversifications of the paralogs in the expanded genomes. The maintenance of the pseudogenes in the large genomes is discussed. © 2011 Wang et al.

Bacterial niche-specific genome expansion is coupled with highly frequent gene disruptions in deep-sea sediments.

Directory of Open Access Journals (Sweden)

Yong Wang

Full Text Available The complexity and dynamics of microbial metagenomes may be evaluated by genome size, gene duplication and the disruption rate between lineages. In this study, we pyrosequenced the metagenomes of microbes obtained from the brine and sediment of a deep-sea brine pool in the Red Sea to explore the possible genomic adaptations of the microbes in response to environmental changes. The microbes from the brine and sediments (both surface and deep layers of the Atlantis II Deep brine pool had similar communities whereas the effective genome size varied from 7.4 Mb in the brine to more than 9 Mb in the sediment. This genome expansion in the sediment samples was due to gene duplication as evidenced by enrichment of the homologs. The duplicated genes were highly disrupted, on average by 47.6% and 70% for the surface and deep layers of the Atlantis II Deep sediment samples, respectively. The disruptive effects appeared to be mainly due to point mutations and frameshifts. In contrast, the homologs from the Atlantis II Deep brine sample were highly conserved and they maintained relatively small copy numbers. Likely, the adaptation of the microbes in the sediments was coupled with pseudogenizations and possibly functional diversifications of the paralogs in the expanded genomes. The maintenance of the pseudogenes in the large genomes is discussed.

Sensitivity and specificity of the nickel spot (dimethylglyoxime) test.

Science.gov (United States)

Thyssen, Jacob P; Skare, Lizbet; Lundgren, Lennart; Menné, Torkil; Johansen, Jeanne D; Maibach, Howard I; Lidén, Carola

2010-05-01

The accuracy of the dimethylglyoxime (DMG) nickel spot test has been questioned because of false negative and positive test reactions. The EN 1811, a European standard reference method developed by the European Committee for Standardization (CEN), is fine-tuned to estimate nickel release around the limit value of the EU Nickel Directive from products intended to come into direct and prolonged skin contact. Because assessments according to EN 1811 are expensive to perform, time consuming, and may destruct the test item, it should be of great value to know the accuracy of the DMG screening test. To evaluate the sensitivity and specificity of the DMG test. DMG spot testing, chemical analysis according to the EN 1811 reference method, and X-ray fluorescence spectroscopy (XRF) were performed concomitantly on 96 metallic components from earrings recently purchased in San Francisco. The sensitivity of the DMG test was 59.3% and the specificity was 97.5% based on DMG-test results and nickel release concentrations determined by the EN 1811 reference method. The DMG test has a high specificity but a modest sensitivity. It may serve well for screening purposes. Past exposure studies may have underestimated nickel release from consumer items.

Significance of flow clustering and sequencing on sediment transport: 1D sediment transport modelling

Science.gov (United States)

Hassan, Kazi; Allen, Deonie; Haynes, Heather

2016-04-01

This paper considers 1D hydraulic model data on the effect of high flow clusters and sequencing on sediment transport. Using observed flow gauge data from the River Caldew, England, a novel stochastic modelling approach was developed in order to create alternative 50 year flow sequences. Whilst the observed probability density of gauge data was preserved in all sequences, the order in which those flows occurred was varied using the output from a Hidden Markov Model (HMM) with generalised Pareto distribution (GP). In total, one hundred 50 year synthetic flow series were generated and used as the inflow boundary conditions for individual flow series model runs using the 1D sediment transport model HEC-RAS. The model routed graded sediment through the case study river reach to define the long-term morphological changes. Comparison of individual simulations provided a detailed understanding of the sensitivity of channel capacity to flow sequence. Specifically, each 50 year synthetic flow sequence was analysed using a 3-month, 6-month or 12-month rolling window approach and classified for clusters in peak discharge. As a cluster is described as a temporal grouping of flow events above a specified threshold, the threshold condition used herein is considered as a morphologically active channel forming discharge event. Thus, clusters were identified for peak discharges in excess of 10%, 20%, 50%, 100% and 150% of the 1 year Return Period (RP) event. The window of above-peak flows also required cluster definition and was tested for timeframes 1, 2, 10 and 30 days. Subsequently, clusters could be described in terms of the number of events, maximum peak flow discharge, cumulative flow discharge and skewness (i.e. a description of the flow sequence). The model output for each cluster was analysed for the cumulative flow volume and cumulative sediment transport (mass). This was then compared to the total sediment transport of a single flow event of equivalent flow volume

The test-retest reliability and criterion validity of a high-intensity, netball-specific circuit test: The Net-Test.

Science.gov (United States)

Mungovan, Sean F; Peralta, Paula J; Gass, Gregory C; Scanlan, Aaron T

2018-04-12

To examine the test-retest reliability and criterion validity of a high-intensity, netball-specific fitness test. Repeated measures, within-subject design. Eighteen female netball players competing in an international competition completed a trial of the Net-Test, which consists of 14 timed netball-specific movements. Players also completed a series of netball-relevant criterion fitness tests. Ten players completed an additional Net-Test trial one week later to assess test-retest reliability using intraclass correlation coefficient (ICC), typical error of measurement (TEM), and coefficient of variation (CV). The typical error of estimate expressed as CV and Pearson correlations were calculated between each criterion test and Net-Test performance to assess criterion validity. Five movements during the Net-Test displayed moderate ICC (0.84-0.90) and two movements displayed high ICC (0.91-0.93). Seven movements and heart rate taken during the Net-Test held low CV (Test possessed low CV and significant (pTest possesses acceptable reliability for the assessment of netball fitness. Further, the high criterion validity for the Net-Test suggests a range of important netball-specific fitness elements are assessed in combination. Copyright © 2018 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

Power-Cooling-Mismatch Test Series Test PCM-7. Experiment operating specifications

International Nuclear Information System (INIS)

Sparks, D.T.; Smith, R.H.; Stanley, C.J.

1979-02-01

The experiment operating specifications for the Power-Cooling-Mismatch (PCM) Test PCM-7 to be conducted in the Power Burst Facility are described. The PCM Test Series was designed on the basis of a parametric evaluation of fuel behavior response with cladding temperature, rod internal pressure, time in film boiling, and test rod power being the variable parameters. The test matrix, defined in the PCM Experiment Requirements Document (ERD), encompasses a wide range of situations extending from pre-CHF (critical heat flux) PCMs to long duration operation in stable film boiling leading to rod failure

Numerical model of turbulence, sediment transport, and morphodynamics tested in the Colorado River at Grand Canyon

Science.gov (United States)

Alvarez, L. V.; Grams, P.

2017-12-01

We present a parallelized, three-dimensional, turbulence-resolving model using the Detached-Eddy Simulation (DES) technique, tested at the scale of the river-reach in the Colorado River. DES is a hybrid large eddy simulation (LES) and Reynolds-averaged Navier Stokes (RANS). RANS is applied to the near-bed grid cells, where grid resolution is not sufficient to fully resolve wall turbulence. LES is applied in the flow interior. We utilize the Spalart-Allmaras one equation turbulence closure with a rough wall extension. The model resolves large-scale turbulence using DES and simultaneously integrates the suspended sediment advection-diffusion equation. The Smith and McLean suspended sediment boundary condition is used to calculate the upward and downward settling of sediment fluxes in the grid cells attached to the bed. Model results compare favorably with ADCP measurements of flow taken on the Colorado River in Grand Canyon during the High Flow Experiment (HFE) of 2008. The model accurately reproduces the size and position of the major recirculation currents, and the error in velocity magnitude was found to be less than 17% or 0.22 m/s absolute error. The mean deviation of the direction of velocity with respect to the measured velocity was found to be 20 degrees. Large-scale turbulence structures with vorticity predominantly in the vertical direction are produced at the shear layer between the main channel and the separation zone. However, these structures rapidly become three-dimensional with no preferred orientation of vorticity. Cross-stream velocities, into the main recirculation zone just upstream of the point of reattachment and out of the main recirculation region just downstream of the point of separation, are highest near the bed. Lateral separation eddies are more efficient at storing and exporting sediment than previously modeled. The input of sediment to the eddy recirculation zone occurs in the interface of the eddy and main channel. Pulsation of the

Quality assurance of radiopharmaceuticals-specifications and test procedures

International Nuclear Information System (INIS)

Baldas, J.; Bonnyman, J.; Pojer, P.M.

1981-08-01

This report is a compilation of test methods used and specifications adopted for the Radiopharmaceutical Quality Assurance Test Programme conducted by the Australian Radiation Laboratory. In some cases test procedures described have been taken from various Pharmacopoeias or methods published in the literature. In other cases test methods have been developed at the ARL

Specification and testing of optics for LIS system

International Nuclear Information System (INIS)

Singh, Sunita; Sridhar, G.; Rawat, V.S.; Gantayet, L.M.

2005-01-01

Optical component specification for the high average power lasers and laser beam transport system used in the laser isotope separation demonstration facility must address demanding system performance requirements. In a typical demonstration facility a few thousand of commercial and custom optical components are required. The optical system is expected to perform at a high level of optical efficiency and reliability. Evaluation and testing of optical components used in LIS plant is critical for qualification of suppliers and assurance of performance in the actual process. The stringent specifications require specialized test equipment and techniques, which are not routine. Careful planning with the optics manufacturer, detailed quality assurance plan, comprehensive procedures for testing and evaluation, and a plan for corrective action are required. The specifications are given on material characteristics, surface quality and flatness, reflectance or transmittance and high average power laser damage. Our approach to specifying, testing the performance characteristics and assuring quality of optical components required for the technology demonstration of laser based isotopic clean-up of 233 U project is presented. (author)

Development, evaluation, and application of sediment quality targets for assessing and managing contaminated sediments in Tampa Bay, Florida

Science.gov (United States)

MacDonald, D.D.; Carr, R.S.; Eckenrod, D.; Greening, H.; Grabe, S.; Ingersoll, C.G.; Janicki, S.; Janicki, T.; Lindskoog, R.A.; Long, E.R.; Pribble, R.; Sloane, G.; Smorong, D.E.

2004-01-01

Tampa Bay is a large, urban estuary that is located in west central Florida. Although water quality conditions represent an important concern in this estuary, information from numerous sources indicates that sediment contamination also has the potential to adversely affect aquatic organisms, aquatic-dependent wildlife, and human health. As such, protecting relatively uncontaminated areas of the bay from contamination and reducing the amount of toxic chemicals in contaminated sediments have been identified as high-priority sediment management objectives for Tampa Bay. To address concerns related to sediment contamination in the bay, an ecosystem-based framework for assessing and managing sediment quality conditions was developed that included identification of sediment quality issues and concerns, development of ecosystem goals and objectives, selection of ecosystem health indicators, establishment of metrics and targets for key indicators, and incorporation of key indicators, metrics, and targets into watershed management plans and decision-making processes. This paper describes the process that was used to select and evaluate numerical sediment quality targets (SQTs) for assessing and managing contaminated sediments. These SQTs included measures of sediment chemistry, whole-sediment and pore-water toxicity, and benthic invertebrate community structure. In addition, the paper describes how the SQTs were used to develop site-specific concentration-response models that describe how the frequency of adverse biological effects changes with increasing concentrations of chemicals of potential concern. Finally, a key application of the SQTs for defining sediment management areas is discussed.

Magnetic properties of Surabaya river sediments, East Java, Indonesia

Science.gov (United States)

Mariyanto, Bijaksana, Satria

2017-07-01

Surabaya river is one of urban rivers in East Java Province, Indonesia that is a part of Brantas river that flows in four urban and industrial cities of Mojokerto, Gresik, Sidoarjo, and Surabaya. The urban populations and industries along the river pose serious threat to the river mainly for their anthropogenic pollutants. This study aims to characterize the magnetic properties of sediments in various locations along Surabaya river and correlate these magnetic properties to the level of pollution along the river. Samples are taken and measured through a series of magnetic measurements. The mass-specific magnetic susceptibility of sediments ranges from 259.4 to 1134.8 × 10-8 m3kg-1. The magnetic minerals are predominantly PSD to MD magnetite with the grain size range from 6 to 14 μm. The mass-specific magnetic susceptibility tends to decreases downstream as accumulation of magnetic minerals in sediments is affected not only by the amount of household and industrial wastes but also by sediment dredging, construction of embankments, and extensive erosion arround the river. Sediments located in the industrial zone on the upstream area tend to have higher mass-specific magnetic susceptibility than in the non-industrial zones on the downstream area.

NIF small optics laser damage test specifications

International Nuclear Information System (INIS)

Sheehan, L

1999-01-01

The Laser Damage Group is currently conducting tests on small optics samples supplied for initial evaluation of potential NIF suppliers. This document is meant to define the specification of laser-induced damage for small optics and the test methods used to collect the data. A rating system which will be applied for vendor selection is presented

Input-variable sensitivity assessment for sediment transport relations

Science.gov (United States)

Fernández, Roberto; Garcia, Marcelo H.

2017-09-01

A methodology to assess input-variable sensitivity for sediment transport relations is presented. The Mean Value First Order Second Moment Method (MVFOSM) is applied to two bed load transport equations showing that it may be used to rank all input variables in terms of how their specific variance affects the overall variance of the sediment transport estimation. In sites where data are scarce or nonexistent, the results obtained may be used to (i) determine what variables would have the largest impact when estimating sediment loads in the absence of field observations and (ii) design field campaigns to specifically measure those variables for which a given transport equation is most sensitive; in sites where data are readily available, the results would allow quantifying the effect that the variance associated with each input variable has on the variance of the sediment transport estimates. An application of the method to two transport relations using data from a tropical mountain river in Costa Rica is implemented to exemplify the potential of the method in places where input data are limited. Results are compared against Monte Carlo simulations to assess the reliability of the method and validate its results. For both of the sediment transport relations used in the sensitivity analysis, accurate knowledge of sediment size was found to have more impact on sediment transport predictions than precise knowledge of other input variables such as channel slope and flow discharge.

Gene expression profiling to characterize sediment toxicity – a pilot study using Caenorhabditis elegans whole genome microarrays

Directory of Open Access Journals (Sweden)

Reifferscheid Georg

2009-04-01

Full Text Available Abstract Background Traditionally, toxicity of river sediments is assessed using whole sediment tests with benthic organisms. The challenge, however, is the differentiation between multiple effects caused by complex contaminant mixtures and the unspecific toxicity endpoints such as survival, growth or reproduction. The use of gene expression profiling facilitates the identification of transcriptional changes at the molecular level that are specific to the bio-available fraction of pollutants. Results In this pilot study, we exposed the nematode Caenorhabditis elegans to three sediments of German rivers with varying (low, medium and high levels of heavy metal and organic contamination. Beside chemical analysis, three standard bioassays were performed: reproduction of C. elegans, genotoxicity (Comet assay and endocrine disruption (YES test. Gene expression was profiled using a whole genome DNA-microarray approach to identify overrepresented functional gene categories and derived cellular processes. Disaccharide and glycogen metabolism were found to be affected, whereas further functional pathways, such as oxidative phosphorylation, ribosome biogenesis, metabolism of xenobiotics, aging and several developmental processes were found to be differentially regulated only in response to the most contaminated sediment. Conclusion This study demonstrates how ecotoxicogenomics can identify transcriptional responses in complex mixture scenarios to distinguish different samples of river sediments.

Standard Specification for Solar Simulation for Terrestrial Photovoltaic Testing

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 This specification provides means for classifying solar simulators intended for indoor testing of photovoltaic devices (solar cells or modules), according to their spectral match to a reference spectral irradiance, non-uniformity of spatial irradiance, and temporal instability of irradiance. 1.2 Testing of photovoltaic devices may require the use of solar simulators. Test Methods that require specific classification of simulators as defined in this specification include Test Methods E948, E1036, and E1362. 1.3 This standard is applicable to both pulsed and steady state simulators and includes recommended test requirements used for classifying such simulators. 1.4 A solar simulator usually consists of three major components: (1) light source(s) and associated power supply; (2) any optics and filters required to modify the output beam to meet the classification requirements in Section 4; and (3) the necessary controls to operate the simulator, adjust irradiance, etc. 1.5 A light source that does not mee...

Testing the behaviour of different kinetic models for uptake/release of radionuclides between water and sediments when implemented in a marine dispersion model

International Nuclear Information System (INIS)

Perianez, R.

2004-01-01

Three kinetic models for adsorption/release of 137 Cs between water and sediments have been tested when they are included in a previously validated dispersion model of the English Channel. Radionuclides are released to the Channel from La Hague nuclear fuel reprocessing plant (France). The kinetic models are a 1-step model consisting of a single reversible reaction, a 2-step model consisting of two consecutive reversible reactions and an irreversible model consisting of three parallel reactions: two reversible and one irreversible. The models have been tested under three typical situations that correspond to the source terms that can generally be found: instantaneous release, continuous release and redissolution of radionuclides from contaminated sediments. Differences between the models become more evident when contact times between water and sediments are larger (continuous release) and in the case of redissolution from sediments. Time scales for the redissolution process are rather different between the three models. The 1-step model produces a redissolution that is too fast when compared with experimental evidence. The irreversible model requires that saturation effects of the irreversible phase are included. Probably, the 2-step model represents the best compromise between ease and level of detail of the description of sorption/release processes

Effects of Aggregation on Blood Sedimentation and Conductivity

Science.gov (United States)

Zhbanov, Alexander; Yang, Sung

2015-01-01

The erythrocyte sedimentation rate (ESR) test has been used for over a century. The Westergren method is routinely used in a variety of clinics. However, the mechanism of erythrocyte sedimentation remains unclear, and the 60 min required for the test seems excessive. We investigated the effects of cell aggregation during blood sedimentation and electrical conductivity at different hematocrits. A sample of blood was drop cast into a small chamber with two planar electrodes placed on the bottom. The measured blood conductivity increased slightly during the first minute and decreased thereafter. We explored various methods of enhancing or retarding the erythrocyte aggregation. Using experimental measurements and theoretical calculations, we show that the initial increase in blood conductivity was indeed caused by aggregation, while the subsequent decrease in conductivity resulted from the deposition of erythrocytes. We present a method for calculating blood conductivity based on effective medium theory. Erythrocytes are modeled as conducting spheroids surrounded by a thin insulating membrane. A digital camera was used to investigate the erythrocyte sedimentation behavior and the distribution of the cell volume fraction in a capillary tube. Experimental observations and theoretical estimations of the settling velocity are provided. We experimentally demonstrate that the disaggregated cells settle much slower than the aggregated cells. We show that our method of measuring the electrical conductivity credibly reflected the ESR. The method was very sensitive to the initial stage of aggregation and sedimentation, while the sedimentation curve for the Westergren ESR test has a very mild slope in the initial time. We tested our method for rapid estimation of the Westergren ESR. We show a correlation between our method of measuring changes in blood conductivity and standard Westergren ESR method. In the future, our method could be examined as a potential means of accelerating

Solidification/stabilization of dredged marine sediments for road construction.

Science.gov (United States)

Wang, Dong Xing; Abriak, Nor Edine; Zentar, Rachid; Xu, WeiYa

2012-01-01

Cement/lime-based solidification is an environmentally sound solution for the management of dredged marine sediments, instead of traditional solutions such as immersion. Based on the mineralogical composition and physical characteristics of Dunkirk sediments, the effects of cement and lime are assessed through Atterberg limits, modified Proctor compaction, unconfined compressive strength and indirect tensile strength tests. The variation of Atterberg limits and the improvement in strength are discussed at different binder contents. The potential of sediments solidified with cement or lime for road construction is evaluated through a proposed methodology from two aspects: I-CBR value and material classification. The test results show the feasibility of solidified dredged sediments for beneficial use as a material in road construction. Cement is superior to lime in terms of strength improvement, and adding 6% cement is an economic and reasonable method to stabilize fine sediments.

A suspended sediment yield predictive equation for river basins in ...

African Journals Online (AJOL)

The fit was found to be better than those relating mean annual specific suspended sediment yield to basin area or runoff only. Since many stream gauging stations in the country have no records on fluvial sediment, the empirical equation can be used to obtain preliminary estimates of expected sediment load of streams for ...

Physical properties of sediments from the JAPEX/JNOC/GSC Mallik 2L-38 gas hydrate research well

Science.gov (United States)

Winters, W.J.

1999-01-01

A 1150 m deep gas hydrate research well was drilled in the Canadian Arctic in February and March 1998 to investigate the interaction between the presence of gas hydrate and the natural conditions presented by the host sediments. Profiles of the following measured and derived properties are presented from that investigation: water content, sediment wet bulk density, grain size, porosity, gas hydrate quantity, and salinity. These data indicate that the greatest concentration of gas hydrate is located within sand and gravel deposits between 897 m and 922 m. American Society for Testing and Materials 1997: Standard test method for specific gravity of soil solids by gas pycnometer D 5550-94; in American Society for Testing and Materials, Annual Book of ASTM Standards, v. 04.09, Soil and Rock, West Conshohocken, Pennsylvania, p. 380-383.

Carbon sources in suspended particles and surface sediments from the Beaufort Sea revealed by molecular lipid biomarkers and compound-specific isotope analysis

Directory of Open Access Journals (Sweden)

I. Tolosa

2013-03-01

Full Text Available Molecular lipid biomarkers (hydrocarbons, alcohols, sterols and fatty acids and compound-specific isotope analysis of suspended particulate organic matter (SPM and surface sediments of the Mackenzie Shelf and slope (southeast Beaufort Sea, Arctic Ocean were studied in summer 2009. The concentrations of the molecular lipid markers, characteristic of known organic matter sources, were grouped and used as proxies to evaluate the relative importance of fresh algal, detrital algal, fossil, C3 terrestrial plants, bacterial and zooplankton material in the organic matter (OM of this area. Fossil and detrital algal contributions were the major fractions of the freshwater SPM from the Mackenzie River with ~34% each of the total molecular biomarkers. Fresh algal, C3 terrestrial, bacterial and zooplanktonic components represented much lower percentages, 17, 10, 4 and 80%, with a minor contribution of fossil and C3 terrestrial biomarkers. Characterization of the sediments revealed a major sink of refractory algal material mixed with some fresh algal material, fossil hydrocarbons and a small input of C3 terrestrial sources. In particular, the sediments from the shelf and at the mouth of the Amundsen Gulf presented the highest contribution of detrital algal material (60–75%, whereas those from the slope contained the highest proportion of fossil (40% and C3 terrestrial plant material (10%. Overall, considering that the detrital algal material is marine derived, autochthonous sources contributed more than allochthonous sources to the OM lipid pool. Using the ratio of an allochthonous biomarker (normalized to total organic carbon, TOC found in the sediments to those measured at the river mouth water, we estimated that the fraction of terrestrial material preserved in the sediments accounted for 30–40% of the total carbon in the inner shelf sediments, 17% in the outer shelf and Amundsen Gulf and up to 25% in the slope sediments. These estimates are low

Relationships between the handball-specific complex test, non-specific field tests and the match performance score in elite professional handball players.

Science.gov (United States)

Hermassi, Souhail; Chelly, Mohamed-Souhaiel; Wollny, Rainer; Hoffmeyer, Birgit; Fieseler, Georg; Schulze, Stephan; Irlenbusch, Lars; Delank, Karl-Stefan; Shephard, Roy J; Bartels, Thomas; Schwesig, René

2018-06-01

This study assessed the validity of the handball-specific complex test (HBCT) and two non-specific field tests in professional elite handball athletes, using the match performance score (MPS) as the gold standard of performance. Thirteen elite male handball players (age: 27.4±4.8 years; premier German league) performed the HBCT, the Yo-Yo Intermittent Recovery (YYIR) test and a repeated shuttle sprint ability (RSA) test at the beginning of pre-season training. The RSA results were evaluated in terms of best time, total time, and fatigue decrement. Heart rates (HR) were assessed at selected times throughout all tests; the recovery HR was measured immediately post-test and 10 minutes later. The match performance score was based on various handball specific parameters (e.g., field goals, assists, steals, blocks, and technical mistakes) as seen during all matches of the immediately subsequent season (2015/2016). The parameters of run 1, run 2, and HR recovery at minutes 6 and 10 of the RSA test all showed a variance of more than 10% (range: 11-15%). However, the variance of scores for the YYIR test was much smaller (range: 1-7%). The resting HR (r2=0.18), HR recovery at minute 10 (r2=0.10), lactate concentration at rest (r2=0.17), recovery of heart rate from 0 to 10 minutes (r2=0.15), and velocity of second throw at first trial (r2=0.37) were the most valid HBCT parameters. Much effort is necessary to assess MPS and to develop valid tests. Speed and the rate of functional recovery seem the best predictors of competitive performance for elite handball players.

Test Specification of A1-1 Test for OECD-ATLAS Project

International Nuclear Information System (INIS)

Kang, Kyoung-Ho; Moon, Sang-Ki; Lee, Seung-Wook; Choi, Ki-Yong; Song, Chul-Hwa

2014-01-01

In the OECD-ATLAS project, design extension conditions (DECs) such as a station blackout (SBO) and a total loss of feed water (TLOFW) will be experimentally investigated to meet the international interests in the multiple high-risk DECs raised after the Fukushima accident. The proposed test matrix for the OECD-ATLAS project is summarized in Table 1.. In this study, detailed specification of the first test named as A1-1 in the OECD-ATLAS project was described. The target scenario of the A1-1 test is a prolonged SBO with delayed supply of turbine-driven auxiliary feedwater to only SG number 2 (SG-2). A SBO is one of the most important DECs in that without any proper operator actions, a total loss of heat sink leads to core uncover, to core damage, and ultimately a core melt-down scenario under high pressure. Due to this safety importance, a SBO is considered to be a base test item of the OECD-ATLAS project. A detailed specification of the first test named as A1-1 in the OECD-ATLAS project was described. The target scenario of the A1-1 test is a prolonged SBO with delayed supply of turbine-driven auxiliary feedwater to only SG-2 in order to consider an accident mitigation measure. The pre-test analysis using MARS code was performed with an aim of setting up the detailed test procedures for A1-1 test and also gaining the physical insights for a prolonged SBO transient. In the A1-1 test, a prolonged SBO transient will be simulated with two temporal phases: Phase (I) for conservative SBO transient without supply of turbine-driven auxiliary feedwater and Phase (II) for asymmetric cooling via single trained supply of turbine-driven auxiliary feedwater

Testing Moral Foundation Theory: Are Specific Moral Emotions Elicited by Specific Moral Transgressions?

Science.gov (United States)

Landmann, Helen; Hess, Ursula

2018-01-01

Moral foundation theory posits that specific moral transgressions elicit specific moral emotions. To test this claim, participants (N = 195) were asked to rate their emotions in response to moral violation vignettes. We found that compassion and disgust were associated with care and purity respectively as predicted by moral foundation theory.…

Critical evaluation of a badminton-specific endurance test.

Science.gov (United States)

Fuchs, Michael; Faude, Oliver; Wegmann, Melissa; Meyer, Tim

2014-03-01

To overcome the limitations of traditional 1-dimensional fitness tests in analyzing physiological properties of badminton players, a badminton-specific endurance test (BST) was created. This study aimed at analyzing the influence of various fitness dimensions on BST performance. 18 internationally competing male German badminton players (22.4 ± 3.2 y, 79.2 ± 7.7 kg, 1.84 ± 0.06 m, world-ranking position [WRP] 21-501) completed a straight-sprint test, a change-of-direction speed test, various jump tests (countermovement jump, drop jump, standing long jump), a multistage running test (MST), and the BST. During this on-court field test players have to respond to a computerized sign indicating direction and speed of badminton-specific movements by moving into the corresponding corners. Significant correlations were found between performance in MST and BST (individual anaerobic threshold [IAT], r = .63, P = .005; maximum velocity [Vmax], r = .60, P = .009). A negative correlation (r = -.59, P = .014) was observed between IAT in BST and drop-jump contact time. No further associations between performance indices could be detected. Apart from a small portion explained by MST results (IAT, R2 = .40; Vmax, R2 = .36), the majority of BST performance cannot be explained by the determined physiological correlates. Moreover, it was impossible to predict the WRP of a player on the basis of BST results (r = -.15, P = .55). Neither discipline-specific performance nor basic physiological properties were appropriately reflected by a BST in elite badminton players. This does not substantiate its validity for regular use as a testing tool. However, it may be useful for monitoring on-court training sessions.

Nonlinear acoustics of water-saturated marine sediments

DEFF Research Database (Denmark)

Jensen, Leif Bjørnø

1976-01-01

Interest in the acoustic qualities of water-saturated marine sediments has increased considerably during recent years. The use of sources of high-intensity sound in oil propsecting, in geophysical and geological studies of bottom and subbottom materials and profiles and recently in marine...... archaeology has emphasized the need of information about the nonlinear acoustic qualities of water-saturated marine sediments. While the acoustic experiments and theoretical investigations hitherto performed have concentrated on a determination of the linear acoustic qualities of water-saturated marine...... sediments, their parameters of nonlinear acoustics are still unexplored. The strong absorption, increasing about linearly with frequency, found in most marine sediments and the occurrence of velocity dispersion by some marine sediments restrict the number of nonlinear acoustic test methods traditionally...

Testing of a uranium downhole logging system to measure in-situ plutonium concentrations in sediments. [216-Z-1A crib

Energy Technology Data Exchange (ETDEWEB)

Kasper, R.B.; Kay, M.A.; Bruns, L.E.; Stokes, J.A.; Steinman, D.K.; Adams, J.

1980-11-01

A prototype urainium borehole logging system, developed for uranium exploration, was modified for Pu assay and testing at the site. It uses the delayed fission neutron (DFN) method. It was tested in a retired Pu facility, the 216-Z-1A Crib. General agreement between laboratory determined Pu concentrations in sediment samples and neutron flux measurements was found for the relative distribution with depth.

OU3 sediment dating and sedimentation rates

International Nuclear Information System (INIS)

Blair, R.B.; Wolaver, H.A.; Burger, V.M.

1994-01-01

Environmental Technologies at Rocky Flats Environmental Technology Site (RFS) investigated the sediment history of Standley Lake, Great Western Reservoir, and Mower Reservoir using 137 Cs and 239,240 Pu global fall-out as dating indicators. These Colorado Front Range reservoirs have been the subject of study by various city, state and national agencies due to suspected Department of Energy Rocky Flats Plant impacts. We performed sediment dating as part of the RCRA Facility Investigation/Remedial Investigation Report for Operable Unit 3. A sediment chronology profile assists scientist in determining the year of sedimentation for a particular peak concentration of contaminants. Radioisotope sediment dating for the three reservoirs indicated sedimentation rates of 0.7 to 0.8 in./yr. for Standley Lake (SL), 0.9 in./yr. for Great Western Reservoir (GWR), and 0.3 in./yr. in Mower Reservoir (MR). RFS sediment dating for Operable Unit 3 compared favorably with the Hardy, Livingston, Burke, and Volchok Standley Lake study. This report describes the cesium/plutonium sediment dating method, estimates sedimentation rates for Operable Unit 3 reservoirs, and compares these results to previous investigations

A sediment graph model based on SCS-CN method

Science.gov (United States)

Singh, P. K.; Bhunya, P. K.; Mishra, S. K.; Chaube, U. C.

2008-01-01

SummaryThis paper proposes new conceptual sediment graph models based on coupling of popular and extensively used methods, viz., Nash model based instantaneous unit sediment graph (IUSG), soil conservation service curve number (SCS-CN) method, and Power law. These models vary in their complexity and this paper tests their performance using data of the Nagwan watershed (area = 92.46 km 2) (India). The sensitivity of total sediment yield and peak sediment flow rate computations to model parameterisation is analysed. The exponent of the Power law, β, is more sensitive than other model parameters. The models are found to have substantial potential for computing sediment graphs (temporal sediment flow rate distribution) as well as total sediment yield.

HPV specific testing: a requirement for oropharyngeal squamous cell carcinoma patients.

Science.gov (United States)

Robinson, Max; Schache, Andrew; Sloan, Philip; Thavaraj, Selvam

2012-07-01

Human papillomavirus (HPV) testing is now recommended as part of the work up for patients with oropharyngeal squamous cell carcinoma (OPSCC) and those patients with cervical lymph node metastasis of unknown origin. The laboratory testing strategy should accurately assess the presence or absence of oncogenic HPV infection in routinely collected tumour samples that are subject to standard fixation protocols, alcohol-fixed cytological preparations and formalin-fixed tissue samples. The HPV status should correlate with biologically relevant outcome measures such as overall, disease-specific and disease-free survival. Whilst increased expression of p16 by immunohistochemistry is considered to be a surrogate marker of oncogenic HPV infection and is a validated independent prognostic biomarker, only HPV specific tests provide definitive evidence of the aetiological agent. We provide an overview of HPV testing in OPSCC, justifying the use of HPV specific tests. We examine the analytical accuracy of HPV specific tests against the 'reference' test--high risk HPV mRNA in fresh tissue--and contrast this with the performance of p16 immunohistochemistry as a stand alone test. We highlight the added value of HPV specific tests in prognostication, clinical trial design, and population-based disease surveillance. We consider that HPV specific testing is the starting point for developing increasingly informative biomarker panels in the context of 'stratified medicine'. We briefly frame test information in the context of disclosure of HPV status to patients. We conclude that only a testing strategy that includes HPV specific tests can deliver more effective care for patients with OPSCC. The international head and neck oncology community should work together to clearly define the minimum requirements for assigning a diagnosis of HPV-related OPSCC in order to ensure consistent reporting of this emerging and increasingly prevalent disease.

Parameter studies of sediments in the Storegga Slide region

Science.gov (United States)

Yang, S. L.; Kvalstad, T.; Solheim, A.; Forsberg, C. F.

2006-09-01

Based on classification tests, oedometer tests, fall-cone tests and triaxial tests, physical and mechanical properties of sediments in the Storegga Slide region were analysed to assess parameter interrelationships. The data show good relationships between a number of physical and mechanical parameters. Goodness of fit between compression index and various physical parameters can be improved by multiple regression analysis. The interclay void ratio and liquidity index correlate well with the undrained shear strength of clay. Sediments with higher water content, liquid limit, activity, interclay void ratio, plasticity index and liquidity index showed higher compression index and/or lower undrained shear strength. Some relationships between parameters were tested by using data from two other sites south of the Storegga Slide. A better understanding of properties of sediments in regions such as that of the Storegga Slide can be obtained through this approach.

Two treatment methods for stormwater sediments--pilot plant and landfarming--and reuse of the treated sediments in civil engineering.

Science.gov (United States)

Petavy, F; Ruban, V; Conil, P; Viau, J Y; Auriol, J C

2009-07-01

The aim of this research was to present a pilot plant for the treatment of stormwater sediments and to compare the decontamination rate to that obtained by landfarming. The possibilities for reuse of the treated sediments in civil engineering are also studied. Four sediments from retention/infiltration ponds or from street sweeping were studied. In each case organic matter (OM), total hydrocarbons (TH) and polycyclic aromatic hydrocarbons (PAH) were measured. Geotechnical tests were carried out to evaluate the reuse possibilities of the treated sediments. Treatment by means of the pilot plant was efficient at reducing TH and PAH concentrations: THs were reduced by 53-97% and PAHs were decreased by 60-95%. By comparison, a reduction of 45-75% in TH concentration is obtained with landfarming, whereas there is no significant decrease in PAHs. Furthermore, geotechnical tests showed that the treated fractions from the pilot plant can be reused as road embankments and as a capping layer. These results are most encouraging and show that stormwater sediments can valuably be reused after treatment in a pilot plant. Landfarming is less efficient but this technique could be used as a pretreatment in the case of high TH pollution.

A closure test for time-specific capture-recapture data

Science.gov (United States)

Stanley, T.R.; Burnham, K.P.

1999-01-01

The assumption of demographic closure in the analysis of capture-recapture data under closed-population models is of fundamental importance. Yet, little progress has been made in the development of omnibus tests of the closure assumption. We present a closure test for time-specific data that, in principle, tests the null hypothesis of closed-population model M(t) against the open-population Jolly-Seber model as a specific alternative. This test is chi-square, and can be decomposed into informative components that can be interpreted to determine the nature of closure violations. The test is most sensitive to permanent emigration and least sensitive to temporary emigration, and is of intermediate sensitivity to permanent or temporary immigration. This test is a versatile tool for testing the assumption of demographic closure in the analysis of capture-recapture data.

Evaluation of PCB bioaccumulation by Lumbriculus variegatus in field-collected sediments

Science.gov (United States)

Sediment bioaccumulation tests with Lumbriculus variegatus were performed on polychlorinated biphenyl (PCBs) contaminated sediment samples from the Hudson, Grasse, and Fox Rivers Superfund sites with concurrent measurement of PCB concentrations in sediment interstitial water. Th...

A Combined Raindrop Aggregate Destruction Test-Settling Tube (RADT-ST Approach to Identify the Settling Velocity of Sediment

Directory of Open Access Journals (Sweden)

Liangang Xiao

2015-10-01

Full Text Available The use of sediment settling velocity based on mineral grain size distribution in erosion models ignores the effects of aggregation on settling velocity. The alternative approach, wet-sieved aggregate size distribution, on the other hand, cannot represent all destructive processes that eroded soils may experience under impacting raindrops. Therefore, without considering raindrop impact, both methods may lead to biased predictions of the redistribution of sediment and associated substances across landscapes. Rainfall simulation is an effective way to simulate natural raindrop impact under controlled laboratory conditions. However, very few methods have been developed to integrate rainfall simulation with the settling velocity of eroded sediment. This study aims to develop a new proxy, based on rainfall simulation, in order to identify the actual settling velocity distribution of aggregated sediment. A combined Raindrop Aggregate Destruction Test-Settling Tube (RADT-ST approach was developed to (1 simulate aggregate destruction under a series of simulated rainfalls; and (2 measure the actual settling velocity distribution of destroyed aggregates. Mean Weight Settling Velocity (MWSV of aggregates was used to investigate settling behaviors of different soils as rainfall kinetic energy increased. The results show the settling velocity of silt-rich raindrop impacted aggregates is likely to be underestimated by at least six times if based on mineral grain size distribution. The RADT-ST designed in this study effectively captures the effects of aggregation on settling behavior. The settling velocity distribution should be regarded as an evolving, rather than steady state parameter during erosion events. The combined RADT-ST approach is able to generate the quasi-natural sediment under controlled simulated rainfall conditions and is adequately sensitive to measure actual settling velocities of differently aggregated soils. This combined approach provides

Specific acyclic isoprenoids as biological markers of methanogenic bacteria in marine sediments.

Science.gov (United States)

Brassell, S C; Wardroper, A M; Thomson, I D; Maxwell, J R; Eglinton, G

1981-04-23

The widespread occurrence of extended hopanoids in sediments and petroleums illustrates the importance of bacterial lipid contributions to geological materials. In archaebacteria, however, hopanoids are absent; their role as structural components of biomembranes is fulfilled by acyclic isoprenoids. Recent studies of the lipid constituents of archaebacteria have greatly extended the range of acyclic isoprenoid skeletons known in organisms (Fig. 1). In particularly, isoprenoids with head-to-head linkages have been identified, and such compounds (for example, 3,7,11,15,18,22,26,30-octamethyldotriacontane, I) have been recognized in petroleum and as degradation products of Messel shale kerogen. Here we report the first recognition of 2,6,10,15,19-pentamethyleicosane (II), a known component of methanogens, in marine sediments of Recent to Cretaceous age (Table 1) and suggest that it and certain other acyclic isoprenoids may be used as biological markers for methanogens.

Sensitivity and specificity of neuropsychological tests for dementia

African Journals Online (AJOL)

specificity of a battery of neuropsychological tests in a sample of elderly persons living in a ... estimate of 20% prevalence for dementia in residential homes ... demographic variables, and mean neuro- psychological .... on optimum balance between sensitivity and specificity (Fig. 1). ..... The lack of stratification of the sample.

Assessing sediment contamination using six toxicity assays

OpenAIRE

Allen G. BURTON Jr.; Carolyn ROWLAND; Renato BAUDO; Monica BELTRAMI

2001-01-01

An evaluation of sediment toxicity at Lake Orta, Italy was conducted to compare a toxicity test battery of 6 assays and to evaluate the extent of sediment contamination at various sediment depths. Lake Orta received excessive loadings of copper and ammonia during the 1900’s until a large remediation effort was conducted in 1989-90 using lime addition. Since that time, the lake has shown signs of a steady recovery of biological communities. The study results showed acute toxicity still exists ...

Subsurface barrier demonstration test strategy and performance specification

International Nuclear Information System (INIS)

Treat, R.L.; Cruse, J.M.

1994-05-01

This document was developed to help specify a major demonstration test project of subsurface barrier systems supporting the Tank Waste Remediation System (TWRS) Program. The document focuses discussion on requirements applicable to demonstration of three subsurface barrier concepts: (1) Injected Material, (2) Cryogenic, and (3) Desiccant. Detailed requirements are provided for initial qualification of a technology proposal followed by the pre-demonstration and demonstration test requirements and specifications. Each requirement and specification is accompanied by a discussion of the rationale for it. The document also includes information on the Hanford Site tank farms and related data; the related and currently active technology development projects within the DOE's EM-50 Program; and the overall demonstration test strategy. Procurement activities and other preparations for actual demonstration testing are on hold until a decision is made regarding further development of subsurface barriers. Accordingly, this document is being issued for information only

Development and Validation of an Aquatic Fine Sediment Biotic Index

Science.gov (United States)

Relyea, Christina D.; Minshall, G. Wayne; Danehy, Robert J.

2012-01-01

The Fine Sediment Biotic Index (FSBI) is a regional, stressor-specific biomonitoring index to assess fine sediment (Plecoptera (5), Trichoptera (3), and Ephemeroptera (2) contained all but one of the species or species groups classified as extremely sensitive. Index validation with an independent data set of 255 streams found FSBI scores to accurately predict both high and low levels of measured fine sediment.

Suspended sediment apportionment in a South-Korean mountain catchment

Science.gov (United States)

Birkholz, Axel; Meusburger, Katrin; Park, Ji-Hyung; Alewell, Christine

2016-04-01

Due to the rapid agricultural expansion and intensification during the last decades in South-Korea, large areas of hill slope forests were transformed to paddies and vegetable fields. The intensive agriculture and the easily erodible soils in our catchment are a major reason for the increased erosion causing suspended sediments to infiltrate into the close drinking water reservoir. The drinking water reservoir Lake Soyang provides water supply for over ten million people in Seoul. Landscape managers need to know the exact origin of these sediments before they can create landscape amelioration schemes. We applied a compound-specific stable isotope (CSSI) approach (Alewell et al., 2015) to apportion the sources of the suspended sediments between forest and agricultural soil contribution to the suspended sediments in a different catchment and applied the same approach to identify and quantify the different sources of the suspended sediments in the river(s) contributing to Lake Soyang. We sampled eight soil sites within the catchment considering the different landuse types forest, rice paddies, maize and vegetables. Suspended sediments were sampled at three outlets of the different sub-catchments. Soils and suspended sediments are analysed for bulk carbon and nitrogen isotopes, compound-specific carbon isotopes of plant-wax derived long-chain fatty acids and long-chain n-alkanes. Fatty acid and alkane isotopes are then used in mixing calculations and the mixing model software IsoSource to find out the contribution of the different source soils to the suspended sediments. We present first data of the source soils and the suspended sediments. C. Alewell, A. Birkholz, K. Meusburger, Y. Schindler-Wildhaber, L. Mabit, 2015. Sediment source attribution from multiple land use systems with CSIA. Biogeosciences Discuss. 12: 14245-14269.

Toxicity of silicon carbide nanowires to sediment-dwelling invertebrates in water or sediment exposures

Science.gov (United States)

Mwangi, Joseph N.; Wang, Ning; Ritts, Andrew; Kunz, James L.; Ingersoll, Christopher G.; Li, Hao; Deng, Baolin

2011-01-01

Silicon carbide nanowires (SiCNW) are insoluble in water. When released into an aquatic environment, SiCNW would likely accumulate in sediment. The objective of this study was to assess the toxicity of SiCNW to four freshwater sediment-dwelling organisms: amphipods (Hyalella azteca), midges (Chironomus dilutus), oligochaetes (Lumbriculus variegatus), and mussels (Lampsilis siliquoidea). Amphipods were exposed to either sonicated or nonsonicated SiCNW in water (1.0 g/L) for 48 h. Midges, mussels, and oligochaetes were exposed only to sonicated SiCNW in water for 96 h. In addition, amphipods were exposed to sonicated SiCNW in whole sediment for 10 d (44% SiCNW on dry wt basis). Mean 48-h survival of amphipods exposed to nonsonicated SiCNW in water was not significantly different from the control, whereas mean survival of amphipods exposed to sonicated SiCNW in two 48-h exposures (0 or 15% survival) was significantly different from the control (90 or 98% survival). In contrast, no effect of sonicated SiCNW was observed on survival of midges, mussels, or oligochaetes. Survival of amphipods was not significantly reduced in 10-d exposures to sonicated SiCNW either mixed in the sediment or layered on the sediment surface. However, significant reduction in amphipod biomass was observed with the SiCNW either mixed in sediment or layered on the sediment surface, and the reduction was more pronounced for SiCNW layered on the sediment. These results indicated that, under the experimental conditions, nonsonicated SiCNW in water were not acutely toxic to amphipods, sonicated SiCNW in water were acutely toxic to the amphipods, but not to other organisms tested, and sonicated SiCNW in sediment affected the growth but not the survival of amphipods.

Variation of a test's sensitivity and specificity with disease prevalence

NARCIS (Netherlands)

Leeflang, Mariska M. G.; Rutjes, Anne W. S.; Reitsma, Johannes B.; Hooft, Lotty; Bossuyt, Patrick M. M.

2013-01-01

Anecdotal evidence suggests that the sensitivity and specificity of a diagnostic test may vary with disease prevalence. Our objective was to investigate the associations between disease prevalence and test sensitivity and specificity using studies of diagnostic accuracy. We used data from 23

Specifically Designed Constructed Wetlands: A Novel Treatment Approach for Scrubber Wastewater

Energy Technology Data Exchange (ETDEWEB)

John H. Rodgers Jr; James W. Castle; Chris Arrington: Derek Eggert; Meg Iannacone

2005-09-01

A pilot-scale wetland treatment system was specifically designed and constructed at Clemson University to evaluate removal of mercury, selenium, and other constituents from flue gas desulfurization (FGD) wastewater. Specific objectives of this research were: (1) to measure performance of a pilot-scale constructed wetland treatment system in terms of decreases in targeted constituents (Hg, Se and As) in the FGD wastewater from inflow to outflow; (2) to determine how the observed performance is achieved (both reactions and rates); and (3) to measure performance in terms of decreased bioavailability of these elements (i.e. toxicity of sediments in constructed wetlands and toxicity of outflow waters from the treatment system). Performance of the pilot-scale constructed wetland treatment systems was assessed using two criteria: anticipated NPDES permit levels and toxicity evaluations using two sentinel toxicity-testing organisms (Ceriodaphnia dubia and Pimephales promelas). These systems performed efficiently with varied inflow simulations of FGD wastewaters removing As, Hg, and Se concentrations below NPDES permit levels and reducing the toxicity of simulated FGD wastewater after treatment with the constructed wetland treatment systems. Sequential extraction procedures indicated that these elements (As, Hg, and Se) were bound to residual phases within sediments of these systems, which should limit their bioavailability to aquatic biota. Sediments collected from constructed wetland treatment systems were tested to observe toxicity to Hyalella azteca or Chironomus tetans. Complete survival (100%) was observed for H. azteca in all cells of the constructed wetland treatment system and C. tentans had an average of 91% survival over the three treatment cells containing sediments. Survival and growth of H. azteca and C. tentans did not differ significantly between sediments from the constructed wetland treatment system and controls. Since the sediments of the constructed

Methane emission in a specific riparian-zone sediment decreased with bioelectrochemical manipulation and corresponded to the microbial community dynamics

Directory of Open Access Journals (Sweden)

Elliot S. Friedman

2016-01-01

Full Text Available Dissimilatory metal-reducing bacteria are widespread in terrestrial ecosystems, especially in anaerobic soils and sediments. Thermodynamically, dissimilatory metal reduction is more favorable than sulfate reduction and methanogenesis but less favorable than denitrification and aerobic respiration. It is critical to understand the complex relationships, including the absence or presence of terminal electron acceptors, that govern microbial competition and coexistence in anaerobic soils and sediments, because subsurface microbial processes can effect greenhouse gas emissions from soils, possibly resulting in impacts at the global scale. Here, we elucidated the effect of an inexhaustible, ferrous-iron and humic-substance mimicking terminal electron acceptor by deploying potentiostatically poised electrodes in the sediment of a very specific stream riparian zone in Upstate New York state. At two sites within the same stream riparian zone during the course of six weeks in the spring of 2013, we measured CH4 and N2/N2O emissions from soil chambers containing either poised or unpoised electrodes, and we harvested biofilms from the electrodes to quantify microbial community dynamics. At the upstream site, which had a lower vegetation cover and highest soil temperatures, the poised electrodes inhibited CH4 emissions by ~45% (when normalized to remove temporal effects. CH4 emissions were not significantly impacted at the downstream site. N2/N2O emissions were generally low at both sites and were not impacted by poised electrodes. We did not find a direct link between bioelectrochemical treatment and microbial community membership; however, we did find a correspondence between environment/function and microbial community dynamics.

Resuspension of polychlorinated biphenyl-contaminated field sediment: release to the water column and determination of site-specific K DOC.

Science.gov (United States)

Friedman, Carey L; Lohmann, Rainer; Burgess, Robert M; Perron, Monique M; Cantwell, Mark G

2011-02-01

Sediments from the New Bedford Harbor (NBH) U.S. Environmental Protection Agency (U.S. EPA) Superfund site (Massachusetts, USA), contaminated with polychlorinated biphenyls (PCBs), were resuspended under different water column redox conditions: untreated, oxidative, and reductive. The partitioning of PCBs to the overlying water column was measured with polyethylene samplers and compared to partitioning without resuspension. Greater concentrations of total aqueous (freely dissolved + dissolved organic carbon (DOC)-associated) PCBs were found in all resuspended treatments for PCBs with mid-range K(OW)s, but no difference was observed in total aqueous concentrations among different redox conditions. The magnitude of increased concentrations depended on resuspension time and congener K(OW), but ranged from approximately one to eight times those found without resuspension. In a parallel study, DOC was flocculated and removed from smaller-scale NBH sediment resuspensions. In situ K(DOC)s were determined and used to calculate freely dissolved and DOC-associated fractions of the increase in total aqueous PCB concentrations due to resuspension. The importance of DOC-associated PCBs increased with increasing K(OW). In situ K(DOC)s were approximately one to two orders of magnitude greater than those calculated with a commonly used linear free energy relationship (LFER). The present study demonstrates that resuspension of contaminated sediments releases PCBs to the water column, of which a significant fraction are DOC-associated (e.g., 28, 65, and 90% for PCBs 28, 66, and 110, respectively). Results also imply that site-specific PCB K(DOC)s are superior to those calculated with generic LFERs. © 2010 SETAC.

Sediment and toxic contaminant transport modeling in coastal waters

International Nuclear Information System (INIS)

Onishi, Yasuo; Mayer, D.W.; Argo, R.S.

1982-01-01

Models are presented to estimate the migration of toxic contaminants in coastal waters. Ocean current is simulated by the vertically-averaged, finite element, two-demensional model known as CAFE-I with the Galerkin weighted residual technique. The refraction of locally generated waves or swells is simulated by the wave refraction model, LO3D. Using computed current, depth, and wave characteristics, the finite element model, FETRA, simulated sediment and contaminant transport in coastal waters, estuaries and rivers. Prior to the application of these models to the Irish Sea and other coastal waters, the finite element model, FETRA, was tested to demonstrate its ability to simulate sediment and contaminant interaction, and the mechanism governing the transport, deposition, and resuspension of contaminated sediment. Several simple equations such as the unsteady, advection-diffusion equation, the equation for noncohesive-sediment load due to wind-induced waves in offshore and surf zones, and the equation for sediment-radionuclide transport simulation were solved during the preliminary testing of the model. (Kato, T.)

Experimental investigation on consistency limits of cement and lime-stabilized marine sediments.

Science.gov (United States)

Wang, DongXing; Zentar, Rachid; Abriak, Nor Edine; Xu, WeiYa

2012-06-01

This paper presents the effects of treatments with cement and lime on the consistency limits of marine sediments dredged from Dunkirk port. The Casagrande percussion test and the fall cone test were used to determine the liquid limits of raw sediments and treated marine sediments. For the evaluation of the plastic limits, the results of the fall cone test were compared with those obtained by the rolling test method. The relationship between the water contents and the penetration depths for the determination of the liquid limit and the plastic limit was explored. Liquid limits at 15.5 mm and plastic limits at 1.55 mm seem to be a more appropriate choice for the studied marine sediments compared with the limits determined by other used prediction methods. Finally, the effect of cement treatment and lime treatment on the Casagrande classification of the studied sediments was investigated according to the different prediction results.

Hanford waste-form release and sediment interaction: A status report with rationale and recommendations for additional studies

International Nuclear Information System (INIS)

Serne, R.J.; Wood, M.I.

1990-05-01

This report documents the currently available geochemical data base for release and retardation for actual Hanford Site materials (wastes and/or sediments). The report also recommends specific laboratory tests and presents the rationale for the recommendations. The purpose of this document is threefold: to summarize currently available information, to provide a strategy for generating additional data, and to provide recommendations on specific data collection methods and tests matrices. This report outlines a data collection approach that relies on feedback from performance analyses to ascertain when adequate data have been collected. The data collection scheme emphasizes laboratory testing based on empiricism. 196 refs., 4 figs., 36 tabs

Sediment problems in reservoirs. Control of sediment deposits

Energy Technology Data Exchange (ETDEWEB)

Jacobsen, Tom

1997-12-31

When a reservoir is formed on a river, sediment will deposit in the reservoir. Such processes are unfortunate, for instance, for the implementation of hydroelectric energy. This thesis studies the problem of reservoir sedimentation and discusses methods of removing the sediments. Various aspects of reservoir sedimentation are discussed. Anthropogenic impacts seem to greatly affect the erosion processes. Temporal distribution is uneven, mainly because of the very large flood events. A world map showing the Reservoir Capacity: Annual Sediment Inflow ratio for reservoirs with volume equal to 10% of annual inflow has been prepared. The map shows that sedimentation is severe in the western parts of North and South America, eastern, southern and northern Africa, parts of Australia and most of Asia. The development of medium-sized reservoirs is difficult, as they are too large for conventional flushing technique and too small to store the sediment that accumulates during their economic lifetime. A computer model, SSIIM, was used with good results in a case study of two flood drawdown trials in Lake Roxburg, New Zealand. Two techniques have been developed that permits controlled suction of sediment and water into a pipe: the Slotted Pipe Sediment Sluicer (SPSS) and the Saxophone Sediment Sluicer (SSS). The techniques exploit the inflow pattern in through a slot in a pipe. An equation describing this inflow pattern was derived and verified experimentally. The SPSS is fixed near the reservoir bed, and sediment that deposits on top of it is removed in the sluicing process. The SSS sluices sediment from the surface of the sediment deposits. Some technical and economic conditions affecting the economics of sediment removal from reservoirs have been identified and studied. 79 refs., 112 figs., 14 tabs.

Runoff and sediment variation in the areas with high and coarse sediment yield of the middle Yellow River

Science.gov (United States)

Zhang, Pan; Yao, Wenyi; Xiao, Peiqing; Sun, Weiying

2018-02-01

Massive water and soil conservation works (WSCW) have been conducted in the areas with high and coarse sediment yield of the middle Yellow River since 1982. With the impending effects of climate change, it is necessary to reconsider the effects of WSCW on runoff and sediment variation at decadal and regional scales. Using long-term official and synthesized data, the WSCW impacts on reducing water and soil loss were studied in Sanchuanhe River watershed. Results showed that the sediment and runoff generated from this area showed a decreasing trend in the past 50 years. A great progress has been achieved in erosion control since the 1970s. After the 4 soil and water conservation harnessing stages during the period from 1970 to 2006, the sediment and runoff yield showed decreases with the extension of harnessing. The results revealed that human activities exerted the largest effects on the sediment reduction and explained 66.6% of the variation in the specific sediment yield. The contribution of rainfall variation to runoff reduction was as large as human activities. A great benefit have been obtained in water and soil loss control in this area.

Specification and acceptance testing of radiotherapy treatment planning systems

International Nuclear Information System (INIS)

2007-04-01

Quality assurance (QA) in the radiation therapy treatment planning process is essential to ensure accurate dose delivery to the patient and to minimize the possibility of accidental exposure. The computerized radiotherapy treatment planning systems (RTPSs) are now widely available in industrialized and developing countries and it is of special importance to support hospitals in Member States in developing procedures for acceptance testing, commissioning and QA of their RTPSs. Responding to these needs, a group of experts developed an IAEA publication with such recommendations, which was published in 2004 as IAEA Technical Reports Series No. 430. This report provides a general framework and describes a large number of tests and procedures that should be considered by the users of new RTPSs. However, small hospitals with limited resources or large hospitals with high patient load and limited staff are not always able to perform complete characterization, validation and software testing of algorithms used in RTPSs. Therefore, the IAEA proposed more specific guidelines that provide a step-by-step recommendation for users at hospitals or cancer centres how to implement acceptance and commissioning procedures for newly purchased RTPSs. The current publication was developed in the framework of the Coordinated Research Project on Development of Procedures for Quality Assurance for Dosimetry Calculations in Radiotherapy and uses the International Electrotechnical Commission (IEC) standard IEC 62083, Requirements for the Safety of Radiotherapy Treatment Planning Systems as its basis. The report addresses the procedures for specification and acceptance testing of RTPSs to be used by both manufacturers and users at the hospitals. Recommendations are provided for specific tests to be performed at the manufacturing facility known as type tests, and for acceptance tests to be performed at the hospital known as site tests. The purpose of acceptance testing is to demonstrate to the

Underwater sediment-contact radiation survey method

International Nuclear Information System (INIS)

Lee, D.R.; St. Aubin, M.; Welch, S.J.

1991-01-01

The authors are striving to produce a practical system for mapping lateral distributions in gamma activity on submerged sediments. This is in response to the need for quality control and interpretation of data obtainable by sediment sampling and analyses near nuclear utilities. A prototype gamma probe has been constructed and tested. The prototype is essentially a background survey meter packaged in a 53-cm-long x 5.4-cm-diam waterproof vehicle. This usage-shaped vehicle is connected to a cable for towing in contact with bottom sediments of lakes, rivers, and coastal waters. This vehicle, or sediment probe as it is called, was initially developed for measuring sediment electrical conductances, a parameter that can be used to locate underwater areas of groundwater and contaminant upwelling. During towing, the probe does not roll or twist around its longitudinal axis by more than 10 deg, so that sensors, which have been fixed within the vehicle, can be oriented to look up, down, or sideways. In over 450 lin-km of underwater survey, only a single sediment probe has been irretrievably snagged on sunken rocks or other debris. Work in the Ottawa River near the Chalk River Laboratories has shown good agreement among point measurements of river sediment with continuous measurements using the moving probe

Fine and coarse components in surface sediments from Bikini Lagoon

Energy Technology Data Exchange (ETDEWEB)

Noshkin, V. E., LLNL

1997-01-01

In 1979, 21 years after the moratorium on nuclear testing in the Marshall Islands, surface sediment samples (to depths of 2 and 4 cm) were collected from 87 locations in the lagoon of Bikini Atoll, one of the two sites in the Marshall Islands used by the United States to test nuclear devices from 1946 through 1958. The main purpose for the collections was to map the distribution of long-lived man-made radionuclides associated with the bottom material. In addition the samples were processed to estimate the fraction of fine and coarse components to show, by comparison, what modifications occurred in the composition since the sediments were first described in samples collected before testing in 1946. Nuclear testing produced more finely divided material that is now found in the surface sediment layer over large areas of the lagoon and especially in regions of the lagoon and reef adjacent to test sites. The 5 cratering events alone at Bikini Atoll redistributed sufficient material to account for the higher inventory of fine material found over the surface 4 cm of the sediment of the lagoon. Although the fraction of fine material in the bottom sediments was altered by the nuclear events, the combined processes of formation, transport and deposition were not sufficiently dynamic to greatly change the general geographical features of the major sedimentary components over most of the lagoon floor.

Effects of dredging operations on sediment quality. Contaminant mobilization in dredged sediments from the Port of Santos, SP, Brazil

Energy Technology Data Exchange (ETDEWEB)

Torres, Ronaldo J.; Santos, Fernando C.; Mozeto, Antonio A. [Lab. de Biogeoquimica Ambiental, Dept. de Quimica, Univ. Federal de Sao Carlos, Sao Paulo, SP (Brazil); Abessa, Denis M.S.; Maranho, Luciane A.; Davanso, Marcela B. [Campus Experimental do Litoral Paulista, UNESP - Univ. Estadual Paulista ' Julio de Mesquita Filho' , Sao Paulo, SP (Brazil); Nascimento, Marcos R.L. do [Lab. de Pocos de Caldas (LAPOC), CNEN-Comissao Nacional de Energia Nuclear, MG (Brazil)

2009-10-15

Background, aim, and scope Contaminated sediments are a worldwide problem, and mobilization of contaminants is one of the most critical issues in environmental risk assessment insofar as dredging projects are concerned. The investigation of how toxic compounds are mobilized during dredging operations in the channel of the Port of Santos, Brazil, was conducted in an attempt to assess changes in the bioavailability and toxicity of these contaminants. Materials and methods Bulk sediment samples and their interstitial waters and elutriates were subjected to chemical evaluation and ecotoxicological assessment. Samples were collected from the channel before dredging, from the dredge's hopper, and from the disposal site and its surroundings. Results The results indicate that the bulk sediments from the dredging site are contaminated moderately with As, Pb, and Zn and severely with Hg, and that polycyclic aromatic hydrocarbon (PAH) concentrations are relatively high. Our results also show a 50% increase in PAH concentrations in suspended solids in the water collected from the hopper dredge. This finding is of great concern, since it refers to the dredge overflow water which is pumped back into the ecosystem. Acute toxicity tests on bulk sediment using the amphipod Tiburonella viscana showed no toxicity, while chronic tests with the sea urchin Lytechinus variegatus showed toxicity in the interstitial waters and elutriates. Results are compared with widely used sediment quality guidelines and with a sediment quality assessment scheme based on various lines of evidence. Conclusions The data presented here indicate that the sediments collected in this port show a certain degree of contamination, especially those from the inner part of the channel. The classification established in this study indicated that sediments from the dredged channel are impacted detrimentally and that sea disposal may disperse contaminants. According to this classification, the sediments are

Biochemical parameters in Tubifex tubifex as an integral part of complex sediment toxicity assessment

Energy Technology Data Exchange (ETDEWEB)

Smutna, M.; Hilscherova, K.; Paskova, V. [Masaryk Univ., Brno (CZ). RECETOX (Research Centre for Environmental Chemistry and Ecotoxicology); Marsalek, B [Czech Academy of Science, Brno (Czech Republic). Centre for Cyanobacteria and their Toxins

2008-06-15

Background, aim, and scope Restoration of lakes and reservoirs with extensive cyanobacterial water bloom often requires evaluation of the sediment quality. Next to the chemical analysis of known pollutants, sediment bioassays should be employed to assess toxicity of the present contaminants and to make predictions of associated risk. Brno reservoir in the Czech Republic is a typical example of water bodies with long-term problems concerning cyanobacterial water blooms. Comprehensive assessment of reservoir sediment quality was conducted since successful reservoir restoration might require sediment removal. An important part of this survey focused on an examination of the utility of Tubifex tubifex and its sublethal biochemical markers for the assessment of direct sediment toxicity. Materials and methods This complex study included chemical analysis of contaminants (heavy metals, organic pollutants), ecotoxicity testing of sediment elutriates (tests with Daphnia magna, Pseudomonas putida, Sinapis alba, Scenedesmus subspicatus), and other parameters. We have tested in more detail the applicability of T. tubifex as a test organism for direct evaluation of contact sediment toxicity. Survival tests after 14 days of exposure were complemented by an assessment of parameters serving as biomarkers for sublethal effects [such as total glutathione content (GSH), activities of the enzymes glutathione transferase (GST), glutathione peroxidase (GPx), and glutathione reductase (GR)]. The data matrix was subjected to multivariate analysis to interpret relationships between different parameters and possible differences among locations. Results The multivariate statistical techniques helped to clearly identify the more contaminated upstream sites and separate them from the less contaminated and reference samples. The data document closer relationships of the detected sediment contamination with results of direct sediment exposure in the T. tubifex test regarding mortality but namely

Comparison of GC-ICP-MS and HPLC-ICP-MS for species-specific isotope dilution analysis of tributyltin in sediment after accelerated solvent extraction

International Nuclear Information System (INIS)

Wahlen, Raimund; Wolff-Briche, Celine

2003-01-01

This study describes a direct comparison of GC and HPLC hyphenated to ICP-MS determination of tributyltin (TBT) in sediment by species-specific isotope dilution analysis (SS-IDMS). The certified reference sediment PACS-2 (NRC, Canada) and a candidate reference sediment (P-18/HIPA-1) were extracted using an accelerated solvent extraction (ASE) procedure. For comparison of GC and LC methods an older bottle of PACS-2 was used, whilst a fresh bottle was taken for demonstration of the accuracy of the methods. The data obtained show good agreement between both methods for both the PACS-2 sediment (LC-ICP-IDMS 828±87 ng g -1 TBT as Sn, GC-ICP-IDMS 848±39 ng g -1 TBT as Sn) and the P-18/ HIPA-1 sediment (LC-ICP-IDMS 78.0±9.7 ng g -1 TBT as Sn, GC-ICP-IDMS 79.2±3.8 ng g -1 TBT as Sn). The analysis by GC-ICP-IDMS offers a greater signal-to-noise ratio and hence a superior detection limit of 0.03 pg TBT as Sn, in the sediment extracts compared to HPLC-ICP-IDMS (3 pg TBT as Sn). A comparison of the uncertainties associated with both methods indicates superior precision of the GC approach. This is related to the better reproducibility of the peak integration, which affects the isotope ratio measurements used for IDMS. The accuracy of the ASE method combined with HPLC-ICP-IDMS was demonstrated during the international interlaboratory comparison P-18 organised by the Comite Consultatif pour la Quantite de Matiere (CCQM). The results obtained by GC-ICP-IDMS for a newly opened bottle of PACS-2 were 1087±77 ng g -1 Sn for DBT and 876±51 ng g -1 Sn for TBT (expanded uncertainties with a coverage factor of 2), which are in good agreement with the certified values of 1090±150 ng g -1 Sn and 980±130 ng g -1 Sn, respectively. (orig.)

Linkages between the spatial toxicity of sediments and sediment dynamics in the Yangtze River Estuary and neighboring East China Sea.

Science.gov (United States)

Gao, Jinjuan; Shi, Huahong; Dai, Zhijun; Mei, Xuefei; Zong, Haibo; Yang, Hongwei; Hu, Lingling; Li, Shushi

2018-02-01

Anthropogenic activities are driving an increase in sediment contamination in coastal areas. This poses significant challenges for the management of estuarine ecosystems and their adjacent seas worldwide. However, few studies have been conducted on how dynamic mechanisms affect the sediment toxicity in the estuarine environment. This study was designed to investigate the linkages between sediment toxicity and hydrodynamics in the Yangtze River Estuary (YRE) area. High sediment toxicity was found in the Yangtze River mouth (Region I), the depocenter of the Yangtze River Delta (Region II), and the southeastern area of the adjacent sea (Region III), while low sediment toxicity was found in the northeastern offshore region (Region IV). A spatial comparison analysis and regression model indicated that the distributed pattern of sediment toxicity was likely related to hydrodynamics and circumfluence in the East China Sea (ECS) shelf. Specifically, high sediment toxicity in Region I may be affected by the Yangtze River Pump (YRP) and the low hydrodynamics there, and high toxicity in Region II can be influenced by the low sediment dynamics and fine sediment in the depocenter. The high sediment toxicity in Region III might be related to the combination of the YRP and Taiwan Warm Current, while the low toxicity in Region IV may be influenced by the local coarse-grained relict sand with strong sediment dynamics there. The present research results further suggest that it is necessary to link hydrodynamics and the spatial behavior of sediment and sediment-derived pollutants when assessing the pollution status of estuarine environments, especially for those mega-estuaries and their neighboring ocean environments with complex waves, tides and ocean currents. Copyright © 2017 Elsevier Ltd. All rights reserved.

Wastewater canal Vojlovica, industrial complex Pančevo, Serbia – preliminary ecotoxicological assessment of contaminated sediment

Directory of Open Access Journals (Sweden)

IVANA PLANOJEVIĆ

2011-03-01

Full Text Available Effluents collected from the industrial complex of Pančevo, Serbia (oil refinery, petrochemical plant, and fertilizer factory, are discharged into a wastewater canal entering the Danube River. In this study, which was focused on sediment assessment, a complex triad approach consisting of chemical analysis, sediment toxicity tests and macrozoobenthos community analysis was applied. In toxicity tests on sediment elutriates, the following responses were registered – stimulatory effect in algal bioassay, no effect in acute test with Daphnia magna, and low to moderate toxicity in the conventional Vibrio fischeri test. Moderate to high toxicities were recorded in solid phase tests on Myriophyllum aquaticum and V. fischeri. High content of Hg, certain PAHs and non-characterised sediment contaminants accumulated over years contribute not only to the registered toxicity, but also to the complete absence of macrozoobenthos. The obtained results proved that regularly measured conventional and priority pollutants are hardly ever the only toxic contaminants present in sediments. Toxicity tests, in particular the contact test, might guide towards a better selection of parameters to be regularly or occasionally monitored. In addition, complete sediment toxicity tests proved to be an appropriate method for assessing the bioavailability of the chemically detected contaminants. The analysis of the macrozoobenthos composition and structure as inevitable part of sediment risk assessment procedures integrates the effects of multiple stressors and gives a realistic insight into not only sediment contamination by toxic pollutants, but also the sediment status in general.

Evaluation of the toxicity of sediments from the Anniston PCB Site to the mussel Lampsilis siliquoidea

Science.gov (United States)

Schein, Allison; Sinclair, Jesse A.; MacDonald, Donald D.; Ingersoll, Christopher G.; Kemble, Nile E.; Kunz, James L.

2015-01-01

concentrations of PCBs were associated with the highest concentrations of PAHs, PCDDs/PCDFs, and organochlorine pesticides. Specifically, sediments 08, 18, and 19 exceeded probable effect concentration quotients (PEC-Qs) of 1.0 for all organic classes of contaminants. These three sediment samples also had high concentrations of mercury and lead, which were the only metals found at elevated concentrations (i.e., above the probable effect concentration [PEC]) in the samples collected. Many sediment samples were highly contaminated with mercury, based on comparisons to samples collected from reference locations. The whole-sediment laboratory toxicity tests conducted with L. siliquoidea met the test acceptability criteria (e.g., control survival was greater than or equal to 80%). Survival of mussels was high in most samples, with 4 of 23 samples (17%) classified as toxic based on the survival endpoint. Biomass and weight were more sensitive endpoints for the L. siliquoidea toxicity tests, with both endpoints classifying 52% of the samples as toxic. Samples 19 and 30 were most toxic to L. siliquoidea, as they were classified as toxic according to all four endpoints (survival, biomass, weight, and length). Mussels were less sensitive in toxicity tests conducted with sediments from the Anniston PCB Site than Hyalella azteca and Chironomus dilutus. Biomass of L. siliquoidea was less sensitive compared to biomass of H. azteca or biomass of larval C. dilutus. Based on the most sensitive endpoint for each species, 52% of the samples were toxic to L. siliquoidea, whereas 67% of sediments were toxic to H. azteca (based on reproduction) and 65% were toxic to C. dilutus (based on adult biomass). The low-risk toxicity threshold (TTLR) was higher for L. siliquoidea biomass (e.g., 20,400 µg/kg dry weight [DW]) compared to that for H. azteca reproduction (e.g., 499 µg/kg DW) or C. dilutus adult biomass (e.g., 1,140 µg/kg DW; MacDonald et al. 2014). While mussels such as L. sili

Study of soil aggregate breakdown dynamics under low dispersive ultrasonic energies with sedimentation and X-ray attenuation

Science.gov (United States)

Schomakers, Jasmin; Zehetner, Franz; Mentler, Axel; Ottner, Franz; Mayer, Herwig

2015-10-01

It has been increasingly recognized that soil organic matter stabilization is strongly controlled by physical binding within soil aggregates. It is therefore essential to measure soil aggregate stability reliably over a wide range of disruptive energies and different aggregate sizes. To this end, we tested highaccuracy ultrasonic dispersion in combination with subsequent sedimentation and X-ray attenuation. Three arable topsoils (notillage) from Central Europe were subjected to ultrasound at four different specific energy levels: 0.5, 6.7, 100 and 500 J cm-3, and the resulting suspensions were analyzed for aggregate size distribution by wet sieving (2 000-63 μm) and sedimentation/X-ray attenuation (63-2 μm). The combination of wet sieving and sedimentation technique allowed for a continuous analysis, at high resolution, of soil aggregate breakdown dynamics after defined energy inputs. Our results show that aggregate size distribution strongly varied with sonication energy input and soil type. The strongest effects were observed in the range of low specific energies (aggregate stability and release of soil organic matter upon aggregate breakdown.

Study of soil aggregate breakdown dynamics under low dispersive ultrasonic energies with sedimentation and X-ray attenuation**

Science.gov (United States)

Schomakers, Jasmin; Zehetner, Franz; Mentler, Axel; Ottner, Franz; Mayer, Herwig

2016-01-01

It has been increasingly recognized that soil organic matter stabilization is strongly controlled by physical binding within soil aggregates. It is therefore essential to measure soil aggregate stability reliably over a wide range of disruptive energies and different aggregate sizes. To this end, we tested high-accuracy ultrasonic dispersion in combination with subsequent sedimentation and X-ray attenuation. Three arable topsoils (notillage) from Central Europe were subjected to ultrasound at four different specific energy levels: 0.5, 6.7, 100 and 500 J cm−3, and the resulting suspensions were analyzed for aggregate size distribution by wet sieving (2 000-63 μm) and sedimentation/X-ray attenuation (63-2 μm). The combination of wet sieving and sedimentation technique allowed for a continuous analysis, at high resolution, of soil aggregate breakdown dynamics after defined energy inputs. Our results show that aggregate size distribution strongly varied with sonication energy input and soil type. The strongest effects were observed in the range of low specific energies (aggregate stability and release of soil organic matter upon aggregate breakdown. PMID:27099408

Earth's portfolio of extreme sediment transport events

Science.gov (United States)

Korup, Oliver

2012-05-01

Quantitative estimates of sediment flux and the global cycling of sediments from hillslopes to rivers, estuaries, deltas, continental shelves, and deep-sea basins have a long research tradition. In this context, extremely large and commensurately rare sediment transport events have so far eluded a systematic analysis. To start filling this knowledge gap I review some of the highest reported sediment yields in mountain rivers impacted by volcanic eruptions, earthquake- and storm-triggered landslide episodes, and catastrophic dam breaks. Extreme specific yields, defined here as those exceeding the 95th percentile of compiled data, are ~ 104 t km- 2 yr- 1 if averaged over 1 yr. These extreme yields vary by eight orders of magnitude, but systematically decay with reference intervals from minutes to millennia such that yields vary by three orders of magnitude for a given reference interval. Sediment delivery from natural dam breaks and pyroclastic eruptions dominate these yields for a given reference interval. Even if averaged over 102-103 yr, the contribution of individual disturbances may remain elevated above corresponding catchment denudation rates. I further estimate rates of sediment (re-)mobilisation by individual giant terrestrial and submarine mass movements. Less than 50 postglacial submarine mass movements have involved an equivalent of ~ 10% of the contemporary annual global flux of fluvial sediment to Earth's oceans, while mobilisation rates by individual events rival the decadal-scale sediment discharge from tectonically active orogens such as Taiwan or New Zealand. Sediment flushing associated with catastrophic natural dam breaks is non-stationary and shows a distinct kink at the last glacial-interglacial transition, owing to the drainage of very large late Pleistocene ice-marginal lakes. Besides emphasising the contribution of high-magnitude and low-frequency events to the global sediment cascade, these findings stress the importance of sediment storage

Equilibrium Partitioning Sediment Benchmarks (ESBs) for the ...

Science.gov (United States)

This document describes procedures to determine the concentrations of nonionic organic chemicals in sediment interstitial waters. In previous ESB documents, the general equilibrium partitioning (EqP) approach was chosen for the derivation of sediment benchmarks because it accounts for the varying bioavailability of chemicals in different sediments and allows for the incorporation of the appropriate biological effects concentration. This provides for the derivation of benchmarks that are causally linked to the specific chemical, applicable across sediments, and appropriately protective of benthic organisms.  This equilibrium partitioning sediment benchmark (ESB) document was prepared by scientists from the Atlantic Ecology Division, Mid-Continent Ecology Division, and Western Ecology Division, the Office of Water, and private consultants. The document describes procedures to determine the interstitial water concentrations of nonionic organic chemicals in contaminated sediments. Based on these concentrations, guidance is provided on the derivation of toxic units to assess whether the sediments are likely to cause adverse effects to benthic organisms. The equilibrium partitioning (EqP) approach was chosen because it is based on the concentrations of chemical(s) that are known to be harmful and bioavailable in the environment.  This document, and five others published over the last nine years, will be useful for the Program Offices, including Superfund, a

The sequence of sediment behaviour during wave-induced liquefaction

DEFF Research Database (Denmark)

Sumer, B. Mutlu; Hatipoglu, Figen; Fredsøe, Jørgen

2006-01-01

to be in agreement with recent centrifuge wave-tank experiments. As for the final stage of the sequence of processes (formation of ripples), the ripple steepness (normalized with the angle of repose) for sediment with liquefaction history is found to be the same as that in sediment with no liquefaction history.......This paper presents the results of an experimental investigation of the complete sequence of sediment behaviour beneath progressive waves. The sediment was silty with d(50) = 0.060 mm. Two kinds of measurements were carried out: pore-water pressure measurements (across the sediment depth...... of liquefaction and compaction fronts in the sediment and (iii) the characteristics of the orbital motion of the liquefied sediment including the motion of the interface between the water body and the sediment. The ranges of the various quantities in the tests were: wave height, H = 9-17 cm, wave period, T = 1...

21 CFR 866.5520 - Immunoglobulin G (Fab fragment specific) immunological test system.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Immunoglobulin G (Fab fragment specific... Test Systems § 866.5520 Immunoglobulin G (Fab fragment specific) immunological test system. (a) Identification. An immunoglobulin G (Fab fragment specific) immunological test system is a device that consists...

21 CFR 866.5540 - Immunoglobulin G (Fd fragment specific) immunological test system.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Immunoglobulin G (Fd fragment specific... Test Systems § 866.5540 Immunoglobulin G (Fd fragment specific) immunological test system. (a) Identification. An immunoglobulin G (Fd fragment specific) immunological test system is a device that consists of...

21 CFR 866.5530 - Immunoglobulin G (Fc fragment specific) immunological test system.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Immunoglobulin G (Fc fragment specific... Test Systems § 866.5530 Immunoglobulin G (Fc fragment specific) immunological test system. (a) Identification. An immunoglobulin G (Fc fragment specific) immunological test system is a device that consists of...

Biodiesel production from sediments of a eutrophic reservoir

International Nuclear Information System (INIS)

Kuchkina, A.Yu.; Gladyshev, M.I.; Sushchik, N.N.; Kravchuk, E.S.; Kalachova, G.S.

2011-01-01

Sediments from eutrophic reservoir Bugach (Siberia, Russia) were tested for possibility to produce biodiesel. We supposed that the sediments could be a promising biodiesel producer. The major reason of high price of biodiesel fuel is cost of a raw material. The use of dredging sediments for biodiesel production reduces production costs, because the dredging sediments are by-products which originated during lake restoration actions, and are free of cost raw materials. Lipid content in sediments was 0.24% of dry weight. To assess the potential of from sediments as a substitute of diesel fuel, the properties of the biodiesel such as cetane number, iodine number and heat of combustion were calculated. All of this parameters complied with limits established by EN 14214 and EN 14213 related to biodiesel quality. -- Highlights: → Dredging sediments were considered as a new feedstock for biodiesel production. → Lipid and fatty acid content in the sediments were determined. → Main properties of the biodiesel were calculated basing on fatty acid composition. → The properties well complied with limits established in biodiesel standards.

210Pb and compositional data of sediments from Rondonian lakes, Madeira River basin, Brazil

International Nuclear Information System (INIS)

Bonotto, Daniel Marcos; Vergotti, Marcelo

2015-01-01

Gold exploration has been intensive in Brazilian Amazon over the last 40 years, where the use of mercury as an amalgam has caused abnormal Hg concentrations in water bodies. Special attention has been directed to Madeira River due to fact it is a major tributary of Amazon River and that since 1986, gold exploration has been officially permitted along a 350 km sector of the river. The 210 Pb method has been used to date sediments taken from nine lakes situated in Madeira River basin, Rondônia State, and to verify where anthropogenic Hg might exist due to gold exploitation in Madeira River. Activity profiles of excess 210 Pb determined in the sediment cores provided a means to evaluate the sedimentation rates using a Constant Flux: Constant Sedimentation (CF:CS) and Constant Rate of Supply (CRS) of unsupported/excess 210 Pb models. A significant relationship was found between the CF:CS sedimentation rates and the mean values of the CRS sedimentation rates (Pearson correlation coefficient r=0.59). Chemical data were also determined in the sediments for identifying possible relationships with Hg occurring in the area. Significant values were found in statistical correlation tests realized among the Hg, major oxides and Total Organic Carbon (TOC) content in the sediments. The TOC increased in the sediment cores accompanied by a loss on ignition (LOI) increment, whereas silica decreased following a specific surface area raising associated to the TOC increase. The CRS model always provided ages within the permitted range of the 210 Pb-method in the studied lakes, whereas the CF:CS model predicted two values above 140 years. - Highlights: • Gold mining activities. • Madeira River basin at Amazon area. • Pb-210 chronological method. • Models for evaluating sedimentation rates

Geno-toxicity assay of sediment and water samples from the Upper Silesia post-mining areas, Poland by means of Allium-test

Energy Technology Data Exchange (ETDEWEB)

Geras' kin, S.; Oudalova, A.; Michalik, B.; Dikareva, N.; Dikarev, V. [Russian Institute of Agricultural Radiology & Agroecology RAAS, Obninsk (Russian Federation)

2011-05-15

Genotoxic potential of two environmental compartments (water and sediment) from the Upper Silesia Coal Basin (USCB), Poland were evaluated and compared by employing root meristem cells of Allium cepa. The clear genotoxic effect of water and sediment sampled was shown, with an important contribution of severe types of cytogenetic abnormalities. The most biologically relevant pollutants were revealed through multivariate statistical analysis of relationships between biological effects registered and the environment contamination. Overall, results of simultaneous use of conventional monitoring methods and biological tests suggested that contemporary levels of persistent pollutants in post-mining areas of the USCB may enhance the risk both for human health and biological components of natural ecosystems.

Interplay between spatially explicit sediment sourcing, hierarchical river-network structure, and in-channel bed material sediment transport and storage dynamics

Science.gov (United States)

Czuba, Jonathan A.; Foufoula-Georgiou, Efi; Gran, Karen B.; Belmont, Patrick; Wilcock, Peter R.

2017-05-01

Understanding how sediment moves along source to sink pathways through watersheds—from hillslopes to channels and in and out of floodplains—is a fundamental problem in geomorphology. We contribute to advancing this understanding by modeling the transport and in-channel storage dynamics of bed material sediment on a river network over a 600 year time period. Specifically, we present spatiotemporal changes in bed sediment thickness along an entire river network to elucidate how river networks organize and process sediment supply. We apply our model to sand transport in the agricultural Greater Blue Earth River Basin in Minnesota. By casting the arrival of sediment to links of the network as a Poisson process, we derive analytically (under supply-limited conditions) the time-averaged probability distribution function of bed sediment thickness for each link of the river network for any spatial distribution of inputs. Under transport-limited conditions, the analytical assumptions of the Poisson arrival process are violated (due to in-channel storage dynamics) where we find large fluctuations and periodicity in the time series of bed sediment thickness. The time series of bed sediment thickness is the result of dynamics on a network in propagating, altering, and amalgamating sediment inputs in sometimes unexpected ways. One key insight gleaned from the model is that there can be a small fraction of reaches with relatively low-transport capacity within a nonequilibrium river network acting as "bottlenecks" that control sediment to downstream reaches, whereby fluctuations in bed elevation can dissociate from signals in sediment supply.

Prediction and forecast of Suspended Sediment Concentration (SSC) on the Upper Yangtze basin

Science.gov (United States)

Matos, José Pedro; Hassan, Marwan; Lu, Xixi; Franca, Mário J.

2017-04-01

Sediment transport in suspension may represent 90% or more of the global annual flux of sediment. For instance, more than 99% of the sediment supplied to the sea by the Yangtze River is suspended load. Suspended load is an important component for understanding channel dynamics and landscape evolution. Sediments transported in suspension are a major source of nutrients for aquatic organisms in riparian and floodplain habitats, and play a beneficial role acting as a sink in the carbon cycle. Excess of fine sediments may also have adverse effects. It can impair fish spawning by riverbed clogging, disturb foraging efficiency of hunting of river fauna, cause algae and benthos scouring, reduce or inhibit exchanges through the hyporheic region. Accumulation of fine sediments in reservoirs reduces storage capacity. Although fine sediment dynamics has been the focus of many studies, the current knowledge of sediment sources, transfer, and storage is inadequate to address fine sediment dynamics in the landscape. The theoretical derivation of a complete model for suspended sediment transport at the basin scale, incorporating small scale processes of production and transport, is hindered because the underlying mechanisms are produced at different non-similar scales. Availability of long-term reliable data on suspended sediment dynamics is essential to improve our knowledge on transport processes and to develop reliable sediment prediction models. Over the last 60 years, the Yangtze River Commission has been measuring the daily Suspended Sediment Concentration (SSC) at the Pingshan station. This dataset provides a unique opportunity to examine temporal variability and controls of fine sediment dynamics in the Upper Yangtze basin. The objective of this study is to describe temporal variation of fine sediment dynamics at the Pingshan station making use of the extensive sediment monitoring program undertaken at that location. We test several strategies of prediction and forecast

Comparison of sport-specific and non-specific exercise testing in inline speed skating.

Science.gov (United States)

Stangier, Carolin; Abel, Thomas; Mierau, Julia; Gutmann, Boris; Hollmann, Wildor; Struder, Heiko K

2016-04-01

The most effective way to measure exercise performance in inline speed skating (ISS) has yet to be established. Generally most athletes are examined by means of traditional but unspecific cycling (CYC) or running (RUN) testing. The present study investigates whether a sport-specific incremental test in ISS reveals different results. Eight male top level inline speed skaters (age: 30±4 years; 65.4±6.3 mL∙kg-1∙min-1, training: 12-14 h/week) performed three incremental exhaustive tests in a randomized order (ergometer CYC, field RUN, field ISS). During the tests, heart rate (HR), oxygen uptake (V̇O2, energy expenditure (EE) and blood lactate concentration (BLC) were measured. Analysis of variance revealed no significant differences for peak HR (187±9, 191±9, 190±9; P=0.75), BLC (10.9±2.3, 10.8±2.4, 8.5±3.2; P=0.25), V̇O2 (65.4±6.3, 66.8±3.5, 66.4±6.5; P=0.91) and EE (1371±165, 1335±93, 1439±196; P=0.51) between ISS and CYC or RUN test. Similar results appeared for HR and V̇O2 at submaximal intensities (2 and 4 mmol·L-1 BLC; P≥0.05). Small to moderate effect sizes 0.3-0.87 and considerable variability of differences between the exercise modes (mean bias range between 1% and 17% with 95% limits of agreement between 3% and 33%) among submaximal and maximal results limit the comparability of the three tests. Consequently, CYC and RUN tests may be considered as qualified alternatives for a challenging ISS test. However a sport-specific test should be conducted in cases of doubt, or when precision is required (e.g. for elite athletes or scientific studies).

Toxicity and biodegradation of PCBs in contaminated sediments

International Nuclear Information System (INIS)

Dercova, K.; Cicmanova, J.; Lovecka, P.; Demnerova, K.; Mackova, M.; Hucko, P.; Kusnir, P.

2006-01-01

PCBs represent a serious ecological problem due to their low degradability, high toxicity, and strong bioaccumulation. Because of many environmental and economical problems, there are efforts to develop bio-remediation technologies for decontamination of the PCB-polluted areas. PCB were used by storage of spent nuclear fuel in nuclear power plants Jaslovske Bohunice. In the locality of the former producer of PCB - Chemko Strazske a. s. - big amount of these substances is still persisting in sediments and soil. The goal of this study was to analyze the contaminated sediments from Strazsky canal and Zemplinska Sirava water reservoir from several points of view. The study of eco-toxicity confirmed that both sediments were toxic for various tested organisms. The genotoxicity test has not proved the mutagenic effect. The subsequent step included microbiological analysis of the contaminated sediments and isolation of pure bacterial cultures capable of degrading PCBs. In order to determine the genetic potential for their biodegradability, the gene bphA1 was identified using PCR technique in their genomes. This gene codes the enzyme biphenyl-dioxygenase, which is responsible for PCB degradation. The final goal was to perform aerobic biodegradation of PCBs in the sediments. The bacteria present in both sediments are able to degrade certain low chlorinated congeners. The issue of biodiversity is still open and has to be studied to reveal the real cooperation between bacteria. (authors)

Toxicity assessment of polluted sediments using swimming behavior alteration test with Daphnia magna

Science.gov (United States)

Nikitin, O. V.; Nasyrova, E. I.; Nuriakhmetova, V. R.; Stepanova, N. Yu; Danilova, N. V.; Latypova, V. Z.

2018-01-01

Recently behavioral responses of organisms are increasingly used as a reliable and sensitive tool in aquatic toxicology. Behavior-related endpoints allow efficiently studying the effects of sub-lethal exposure to contaminants. At present behavioural parameters frequently are determined with the use of digital analysis of video recording by computer vision technology. However, most studies evaluate the toxicity of aqueous solutions. Due to methodological difficulties associated with sample preparation not a lot of examples of the studies related to the assessment of toxicity of other environmental objects (wastes, sewage sludges, soils, sediments etc.) by computer vision technology. This paper presents the results of assessment of the swimming behavior alterations of Daphnia magna in elutriates from both uncontaminated natural and artificially chromium-contaminated bottom sediments. It was shown, that in elutriate from chromium contaminated bottom sediments (chromium concentration 115±5.7 μg l-1) the swimming speed of daphnids was decreases from 0.61 cm s-1 (median speed over the period) to 0.50 cm s-1 (median speed at the last minute of the experiment). The relocation of Daphnia from the culture medium to the extract from the non-polluted sediments does not essential changes the swimming activity.

Characterization of 200-UP-1 Aquifer Sediments and Results of Sorption-Desorption Tests Using Spiked Uncontaminated Groundwater

Energy Technology Data Exchange (ETDEWEB)

Um, Wooyong; Serne, R JEFFREY.; Bjornstad, Bruce N.; Schaef, Herbert T.; Brown, Christopher F.; Legore, Virginia L.; Geiszler, Keith N.; Baum, Steven R.; Valenta, Michelle M.; Kutnyakov, Igor V.; Vickerman, Tanya S.; Lindberg, Michael J.

2005-11-16

increasing concentrations of carbonate up to a point. Then as carbonate and calcium concentrations in the groundwater reach values that exceed the solubility limit for the mineral calcite there is a slight increase in U(VI) Kd likely caused by uranium co-precipitation with the fresh calcite. If remediation of the UP-1 groundwater plume is required, such as pump and treat, it is recommended that the aquifer be treated with chemicals to increase pH and alkalinity and decrease dissolved calcium and magnesium [so that the precipitation of calcite is prevented]. Alternative methods to immobilize the uranium in place might be more effective than trying to remove the uranium by pump and treat. Unfortunately, no aquifer sediments were obtained that contained enough Hanford generated uranium to perform quantitative desorption tests germane to the UP-1 plume remediation issue. Recommended Kd values that should be used for risk predictions for the UP-1 groundwater plume traveling through the lithologies within the aquifer present at the UP-1 (and by proxy ZP-1) operable units were provided. The recommended values Kd values are chosen to include some conservatism (lower values are emphasized from the available range) as is standard risk assessment practice. In general, desorption Kd values for aged contaminated sediments can be larger than Kd values determined in short-term laboratory experiments. To accommodate the potential for desorption hysteresis and other complications, a second suite of uranium desorption Kd values were provided to be used to estimate removal of uranium by pump and treat techniques.

Monitoring changes in stream bottom sediments and benthic invertebrates.

Science.gov (United States)

1981-01-01

The study was conducted to determine whether the analysis of stream bottom sediments could be used to assess sediment pollution generated by highway construction. Most of the work completed to date has involved testing and refining methods for the co...

Effect Of Environmental Load On The Toxicity Of Bottom Sediments

Directory of Open Access Journals (Sweden)

Šestinová Oľga

2015-06-01

Full Text Available This study is devoted to Ecotoxicity tests, Terrestrial Plant Test (modification of OECD 208, Phytotoxkit microbiotest on Sinapis alba and chronic tests of Earthworm (Eisenia veneta, modification of OECD Guidelines for the testing of chemicals 317, Bioaccumulation in Terrestrial Oligochaetes on polluted sediments. Earthworms can accelerate the removal of contaminants from soil. The study materials are river sediments, which were obtained from a monitoring station - the Water reservoir the Ružín No.1 particularly, the river Hornád, Hnilec and sample from sludge bed Rudňany. The samples of sediment were used to assess of the potential phytotoxic effect of heavy metals on higher plants. Total mortality was established in earthworms using chronic toxicity test after 7 and 28 exposure days. Based on the phytotoxicity testing, phytotoxic effects of the metals contaminated sediments from the sludge bed Rudňany on S. alba seeds was observed. The largest concentration differences were recorded in the sample R7 after 7 days earthworms exposure. The earthworms mortality was not influenced by sediment neither after 7 nor 28 exposure days The spectra of samples H, HO and R showed broad peak at 1 419 - 1 512 cm−1 characteristic for carbonate radical. In the spectra of the samples (R and R7 the vibration of C-H groups at 2 926 and 2 921 cm−1, respectively were also observed, demonstrating the presence of organic matter. Our research will continue with determination of metals concentration in earthworms.

An evaluation of contaminated estuarine sites using sediment quality guidelines and ecological assessment methodologies.

Science.gov (United States)

Fulton, M; Key, P; Wirth, E; Leight, A K; Daugomah, J; Bearden, D; Sivertsen, S; Scott, G

2006-10-01

Toxic contaminants may enter estuarine ecosystems through a variety of pathways. When sediment contaminant levels become sufficiently high, they may impact resident biota. One approach to predict sediment-associated toxicity in estuarine ecosystems involves the use of sediment quality guidelines (ERMs, ERLs) and site-specific contaminant chemistry while a second approach utilizes site-specific ecological sampling to assess impacts at the population or community level. The goal of this study was to utilize an integrated approach including chemical contaminant analysis, sediment quality guidelines and grass shrimp population monitoring to evaluate the impact of contaminants from industrial sources. Three impacted sites and one reference site were selected for study. Grass shrimp populations were sampled using a push-netting approach. Sediment samples were collected at each site and analyzed for metals, polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs) and pesticides. Contaminant levels were then compared to sediment quality guidelines. In general, grass shrimp population densities at the sites decreased as the ERM quotients increased. Grass shrimp densities were significantly reduced at the impacted site that had an ERM exceedance for chromium and the highest Mean ERM quotient. Regression analysis indicated that sediment chromium concentrations were negatively correlated with grass shrimp density. Grass shrimp size was reduced at two sites with intermediate levels of contamination. These findings support the use of both sediment quality guidelines and site-specific population monitoring to evaluate the impacts of sediment-associated contaminants in estuarine systems.

A survey of benthic sediment contaminants in reaches of the Columbia River Estuary based on channel sedimentation characteristics.

Science.gov (United States)

Counihan, Timothy D; Waite, Ian R; Nilsen, Elena B; Hardiman, Jill M; Elias, Edwin; Gelfenbaum, Guy; Zaugg, Steven D

2014-06-15

While previous studies have documented contaminants in fish, sediments, water, and wildlife, few specifics are known about the spatial distribution of contaminants in the Columbia River Estuary (CRE). Our study goal was to characterize sediment contaminant detections and concentrations in reaches of the CRE that were concurrently being sampled to assess contaminants in water, invertebrates, fish, and osprey (Pandion haliaetus) eggs. Our objectives were to develop a survey design based on sedimentation characteristics and then assess whether sediment grain size, total organic carbon (TOC), and contaminant concentrations and detections varied between areas with different sedimentation characteristics. We used a sediment transport model to predict sedimentation characteristics of three 16km river reaches in the CRE. We then compartmentalized the modeled change in bed mass after a two week simulation to define sampling strata with depositional, stable, or erosional conditions. We collected and analyzed bottom sediments to assess whether substrate composition, organic matter composition, and contaminant concentrations and detections varied among strata within and between the reaches. We observed differences in grain size fractions between strata within and between reaches. We found that the fine sediment fraction was positively correlated with TOC. Contaminant concentrations were statistically different between depositional vs. erosional strata for the industrial compounds, personal care products and polycyclic aromatic hydrocarbons class (Indus-PCP-PAH). We also observed significant differences between strata in the number of detections of Indus-PCP-PAH (depositional vs. erosional; stable vs. erosional) and for the flame retardants, polychlorinated biphenyls, and pesticides class (depositional vs. erosional, depositional vs. stable). When we estimated mean contaminant concentrations by reach, we observed higher contaminant concentrations in the furthest downstream

A survey of benthic sediment contaminants in reaches of the Columbia River Estuary based on channel sedimentation characteristics

Science.gov (United States)

Counihan, Timothy D.; Waite, Ian R.; Nilsen, Elena B.; Hardiman, Jill M.; Elias, Edwin; Gelfenbaum, Guy; Zaugg, Steven D.

2014-01-01

While previous studies have documented contaminants in fish, sediments, water, and wildlife, few specifics are known about the spatial distribution of contaminants in the Columbia River Estuary (CRE). Our study goal was to characterize sediment contaminant detections and concentrations in reaches of the CRE that were concurrently being sampled to assess contaminants in water, invertebrates, fish, and osprey (Pandion haliaetus) eggs. Our objectives were to develop a survey design based on sedimentation characteristics and then assess whether sediment grain size, total organic carbon (TOC), and contaminant concentrations and detections varied between areas with different sedimentation characteristics. We used a sediment transport model to predict sedimentation characteristics of three 16 km river reaches in the CRE. We then compartmentalized the modeled change in bed mass after a two week simulation to define sampling strata with depositional, stable, or erosional conditions. We collected and analyzed bottom sediments to assess whether substrate composition, organic matter composition, and contaminant concentrations and detections varied among strata within and between the reaches. We observed differences in grain size fractions between strata within and between reaches. We found that the fine sediment fraction was positively correlated with TOC. Contaminant concentrations were statistically different between depositional vs. erosional strata for the industrial compounds, personal care products and polycyclic aromatic hydrocarbons class (Indus–PCP–PAH). We also observed significant differences between strata in the number of detections of Indus–PCP–PAH (depositional vs. erosional; stable vs. erosional) and for the flame retardants, polychlorinated biphenyls, and pesticides class (depositional vs. erosional, depositional vs. stable). When we estimated mean contaminant concentrations by reach, we observed higher contaminant concentrations in the furthest

Fractions and Distribution of Phosphorus in Sediments of the Yarlung Zangbo River Basin

Science.gov (United States)

Huang, W.; An, R.; Huang, Y.; Pu, X.; Li, R.; Li, J.

2017-12-01

The Yarlung Zangbo River is one of the highest rivers in the world. The ecological environment of the river basin has its specificity. It locates in the remote area of China, and the ecological environment is very fragile. The fundamental data of phosphorus content in sediments of the Yarlung Zangbo River Basin are very scarce. In order to clarify the distribution law of phosphorus in the sediments of this area and provide the fundamental data for the study of phosphorus transport in the Yarlung Zangbo River, the authors collected the sediment samples from the mainstream and its tributaries in the research area. Their particle size distributions, specific surface areas, contents of total phosphorus, organic phosphorus and different forms of inorganic phosphorus were analyzed. Then, the fractions and spatial distribution of these forms phosphorus were studied. The results showed that the fractions and distribution characteristics of phosphorus in each form are significant different in the sediments of the Yarlung Zangbo River. The phosphorus contents in the soil erosion deposits and river bed sediment samples are also different. The phosphorus content in sediment is significantly correlated with the sediment characteristics. Keywords: the Yarlung Zangbo River; sediments; fractions of phosphorus; distribution characteristics

Toxicity of sediments and pore water from Brunswick Estuary, Georgia

Science.gov (United States)

Winger, Parley V.; Lasier, Peter J.; Geitner, Harvey

1993-01-01

A chlor-alkali plant in Brunswick, Georgia, USA, discharged >2 kg mercury/d into a tributary of the Turtle River-Brunswick Estuary from 1966 to 1971. Mercury concentrations in sediments collected in 1989 along the tributary near the chlor-alkali plant ranged from 1 to 27 μg/g (dry weight), with the highest concentrations found in surface (0–8 cm) sediments of subtidal zones in the vicinity of the discharge site. Toxicity screening in 1990 using Microtox® bioassays on pore water extracted on site from sediments collected at six stations distributed along the tributary indicated that pore water was highly toxic near the plant discharge. Ten-day toxicity tests on pore water from subsequent sediment samples collected near the plant discharge confirmed high toxicity to Hyalella azteca, and feeding activity was significantly reduced in whole-sediment tests. In addition to mercury in the sediments, other metals (chromium, lead, and zinc) exceeded 50 μg/g, and polychlorobiphenyl (PCB) concentrations ranged from 67 to 95 μg/g. On a molar basis, acid-volatile sulfide concentrations (20–45 μmol/g) in the sediments exceeded the metal concentrations. Because acid-volatile sulfides bind with cationic metals and form metal sulfides, which are generally not bioavailable, toxicities shown by these sediments were attributed to the high concentrations of PCBs and possibly methylmercury.

A multiscale approach to mapping seabed sediments.

Directory of Open Access Journals (Sweden)

Benjamin Misiuk

Full Text Available Benthic habitat maps, including maps of seabed sediments, have become critical spatial-decision support tools for marine ecological management and conservation. Despite the increasing recognition that environmental variables should be considered at multiple spatial scales, variables used in habitat mapping are often implemented at a single scale. The objective of this study was to evaluate the potential for using environmental variables at multiple scales for modelling and mapping seabed sediments. Sixteen environmental variables were derived from multibeam echosounder data collected near Qikiqtarjuaq, Nunavut, Canada at eight spatial scales ranging from 5 to 275 m, and were tested as predictor variables for modelling seabed sediment distributions. Using grain size data obtained from grab samples, we tested which scales of each predictor variable contributed most to sediment models. Results showed that the default scale was often not the best. Out of 129 potential scale-dependent variables, 11 were selected to model the additive log-ratio of mud and sand at five different scales, and 15 were selected to model the additive log-ratio of gravel and sand, also at five different scales. Boosted Regression Tree models that explained between 46.4 and 56.3% of statistical deviance produced multiscale predictions of mud, sand, and gravel that were correlated with cross-validated test data (Spearman's ρmud = 0.77, ρsand = 0.71, ρgravel = 0.58. Predictions of individual size fractions were classified to produce a map of seabed sediments that is useful for marine spatial planning. Based on the scale-dependence of variables in this study, we concluded that spatial scale consideration is at least as important as variable selection in seabed mapping.

Evaluation of Wetland Creation with John F. Baldwin Ship Channel Sediment

National Research Council Canada - National Science Library

Led, C

2000-01-01

.... Sediments were sampled and tested to determine the physical and chemical characteristics. Little sediment contamination was found except for elevated levels of polycyclic aromatic hydrocarbons (PAHs...

Increased carbon uptake in marine sediment enabled by naturally occurring electrical conductors

Science.gov (United States)

Nielsen, M. E.; Cahoon, D. P.; Girguis, P. R.

2011-12-01

Reduction-oxidation (redox) gradients are common across marine sediment-water interfaces and result from microbially-mediated reactions such as the oxidation of organic matter coupled to reduction of electron acceptors. Most microbes living in sediments do not have direct access to oxygen in their immediate environment, however it has recently been shown that sulfide-oxidizing microbes may employ extracellular electron transfer (EET) to couple the oxidation of sulfide in the anoxic zone to reduction of oxygen at the sediment-water interface located several centimeters away. However, no mechanisms for this observed phenomenon have been validated. Accordingly, we tested the hypothesis that conductive minerals in marine sediment (specifically pyrite) can couple spatially separated redox reactions such as anaerobic respiration and oxygen reduction. Marine sediment was amended with naturally occurring pyrite in varying concentrations (0, 2, 10 and 50 weight-percent) and then incubated with 10 μM 13C-labeled acetate. After six hours, the treatments with the greatest amount of added pyrite showed the greatest incorporation of acetate from the labeled pool. The fraction of labeled acetate incorporation more than doubled in the 10 and 50 weight-percent treatments compared to the control sediment. We also designed a circuit to investigate the electrical conductivity of the sediment treatments as a function of added pyrite. A potentiostat was used to establish a known voltage across a sediment column and current was measured. Resistance (the inverse of conductance) was calculated from a linear fit of current data over a range of voltages ranging from 0.5 to 1.0 V. The treatments with added pyrite had lower resistance than background sediment, with the lowest resistance corresponding to the 50% pyrite treatment. We also examined the effect of varying pyrite content on microbial community composition using massively parallel 16S rRNA sequencing. Microbial community analyses

Uranium-series comminution ages of continental sediments: Case study of a Pleistocene alluvial fan

Energy Technology Data Exchange (ETDEWEB)

Lee, Victoria E.; DePaolo, Donald J.; Christensen, John N.

2010-04-30

Obtaining quantitative information about the timescales associated with sediment transport, storage, and deposition in continental settings is important but challenging. The uranium-series comminution age method potentially provides a universal approach for direct dating of Quaternary detrital sediments, and can also provide estimates of the sediment transport and storage timescales. (The word"comminution" means"to reduce to powder," reflecting the start of the comminution age clock as reduction of lithic parent material below a critical grain size threshold of ~;;50 mu m.) To test the comminution age method as a means to date continental sediments, we applied the method to drill-core samples of the glacially-derived Kings River Fan alluvial deposits in central California. Sediments from the 45 m core have independently-estimated depositional ages of up to ~;;800 ka, based on paleomagnetism and correlations to nearby dated sediments. We characterized sequentially-leached core samples (both bulk sediment and grain size separates) for U, Nd, and Sr isotopes, grain size, surface texture, and mineralogy. In accordance with the comminution age model, where 234U is partially lost from small sediment grains due to alpha recoil, we found that (234U/238U) activity ratios generally decrease with age, depth, and specific surface area, with depletions of up to 9percent relative to radioactive equilibrium. The resulting calculated comminution ages are reasonable, although they do not exactly match age estimates from previous studies and also depend on assumptions about 234U loss rates. The results indicate that the method may be a significant addition to the sparse set of available tools for dating detrital continental sediments, following further refinement. Improving the accuracy of the method requires more advanced models or measurements for both the recoil loss factor fa and weathering effects. We discuss several independent methods for obtaining fa on individual samples

(210)Pb and compositional data of sediments from Rondonian lakes, Madeira River basin, Brazil.

Science.gov (United States)

Bonotto, Daniel Marcos; Vergotti, Marcelo

2015-05-01

Gold exploration has been intensive in Brazilian Amazon over the last 40 years, where the use of mercury as an amalgam has caused abnormal Hg concentrations in water bodies. Special attention has been directed to Madeira River due to fact it is a major tributary of Amazon River and that since 1986, gold exploration has been officially permitted along a 350km sector of the river. The (21)(0)Pb method has been used to date sediments taken from nine lakes situated in Madeira River basin, Rondônia State, and to verify where anthropogenic Hg might exist due to gold exploitation in Madeira River. Activity profiles of excess (21)(0)Pb determined in the sediment cores provided a means to evaluate the sedimentation rates using a Constant Flux: Constant Sedimentation (CF:CS) and Constant Rate of Supply (CRS) of unsupported/excess (21)(0)Pb models. A significant relationship was found between the CF:CS sedimentation rates and the mean values of the CRS sedimentation rates (Pearson correlation coefficient r=0.59). Chemical data were also determined in the sediments for identifying possible relationships with Hg occurring in the area. Significant values were found in statistical correlation tests realized among the Hg, major oxides and Total Organic Carbon (TOC) content in the sediments. The TOC increased in the sediment cores accompanied by a loss on ignition (LOI) increment, whereas silica decreased following a specific surface area raising associated to the TOC increase. The CRS model always provided ages within the permitted range of the (21)(0)Pb-method in the studied lakes, whereas the CF:CS model predicted two values above 140 years. Copyright © 2015 Elsevier Ltd. All rights reserved.

Consolidation and strength properties of calcareous sediments from Kaneohe and Kailua Bays, Hawaii

Digital Repository Service at National Institute of Oceanography (India)

Brandes, H.G.; Khadge, N.H.; Nakayama, D.D.

behavior of marine calcareous sediments of biogenic origin. Consolidation and drained triaxial tests indicate that mixed sediments have higher compressibilities and lower strengths compared to high-carbonate sediments. Differences in gradation among high...

In situ time-series measurements of subseafloor sediment properties

Science.gov (United States)

Wheatcroft, R.A.; Stevens, A.W.; Johnson, R.V.

2007-01-01

The capabilities and diversity of subsurface sediment sensors lags significantly from what is available for the water column, thereby limiting progress in understanding time-dependent seabed exchange and high-frequency acoustics. To help redress this imbalance, a new instrument, the autonomous sediment profiler (ASP), is described herein. ASP consists of a four-electrode, Wenner-type resistivity probe and a thermistor that log data at 0.1-cm vertical intervals over a 58-cm vertical profile. To avoid resampling the same spot on the seafloor, the probes are moved horizontally within a 20 times 100-cm-2 area in one of three preselected patterns. Memory and power capacities permit sampling at hourly intervals for up to 3-mo duration. The system was tested in a laboratory tank and shown to be able to resolve high-frequency sediment consolidation, as well as changes in sediment roughness. In a field test off the southern coast of France, the system collected resistivity and temperature data at hourly intervals for 16 d. Coupled with environmental data collected on waves, currents, and suspended sediment, the ASP is shown to be useful for understanding temporal evolution of subsurface sediment porosity, although no large depositional or erosional events occurred during the deployment. Following a rapid decrease in bottom-water temperature, the evolution of the subsurface temperature field was consistent with the 1-D thermal diffusion equation coupled with advection in the upper 3-4 cm. Collectively, the laboratory and field tests yielded promising results on time-dependent seabed change.

Acetate consumption in anoxic marine sediments: Identification of key players using mixed pure cultures and sediment incubations

DEFF Research Database (Denmark)

Na, Hyunsoo

. While we did not find methanogens to be involved in acetate consumption with sediment incubations, the results from co-culture experiments show that syntrophic growth may allow aceticlastic methanogens to co-exist with sulfate-reducing bacteria in anoxic, sulfate-rich marine environments....... are largely unknown. The main goal of my PhD project was to identify acetate consumers in sulfate-reducing sediments of Aarhus Bay, Denmark. More specifically, we addressed the hypothesis if sulfate-reducing bacteria and methanogenic archaea can oxidize acetate in syntrophy. First, we examined the changes...... sulfate for a year were comparable to those of sediment incubated with high sulfate, on phylum/class levels, but within Deltaproteobacteria, certain sulfate reducers such as Desulfobacterium anilini was found only with low sulfate. In continuous flow-through reactors, bacteria mainly involved in sulfur...

Sediment remediation of the Hespeler Mill Pond, Cambridge, Ontario

Energy Technology Data Exchange (ETDEWEB)

Angeloni, D.; Eby, M.; Jarvis, S.; Martin, P. [Univ. of Guelph, School of Engineering, Guelph, Ontario (Canada)]. E-mail: danielle.angeloni@earthtech.ca

2002-06-15

'Full text:' Low dissolved oxygen levels and large accumulated sediment remediation alternatives were examined to assemble the Hespeler Mill Pond, Cambridge (HMP) into a healthier and more desirable recreational area in the City of Cambridge. The theory that a large amount of sediment has been deposited into the HMP from the Speed River upstream over a number of years predicts the depressed oxygen levels, high nutrient-loading rates and the odour problems in the summer months. The initial phase in the remediation plan for this project involved extensive background research and investigation. The focus was on determining the characteristics of the sediment and the history of the pond, to ultimately decide if the sediment was the source of the issues. Dissolved oxygen field tests and sediment sampling were conducted to get information on the magnitude of the problem and the environmental hazards potentially present in the pond. The pond was modelled utilising the Streeter-Phelps oxygen-sag model to predict the oxygen deficit. Biochemical Oxygen Demand (BOD{sub 5}) testing was completed to determine the oxygen demand in the pond. These tests were conducted by using water samples obtained from various sample points at the pond. The proposed solution is a combined dredging and aeration approach. Mechanical dredging using a clamshell bucket and the installation of aerators is expected to solve the dissolved oxygen and water quality issues. (author)

Water and Sediment Output Evaluation Using Cellular Automata on Alpine Catchment: Soana, Italy - Test Case

Science.gov (United States)

Pasculli, Antonio; Audisio, Chiara; Sciarra, Nicola

2017-12-01

In the alpine contest, the estimation of the rainfall (inflow) and the discharge (outflow) data are very important in order to, at least, analyse historical time series at catchment scale; determine the hydrological maximum and minimum estimate flood and drought frequency. Hydrological researches become a precious source of information for various human activities, in particular for land use management and planning. Many rainfall- runoff models have been proposed to reflect steady, gradually-varied flow condition inside a catchment. In these last years, the application of Reduced Complexity Models (RCM) has been representing an excellent alternative resource for evaluating the hydrological response of catchments, within a period of time up to decades. Hence, this paper is aimed at the discussion of the application of the research code CAESAR, based on cellular automaton (CA) approach, in order to evaluate the water and the sediment outputs from an alpine catchment (Soana, Italy), selected as test case. The comparison between the predicted numerical results, developed through parametric analysis, and the available measured data are discussed. Finally, the analysis of a numerical estimate of the sediment budget over ten years is presented. The necessity of a fast, but reliable numerical support when the measured data are not so easily accessible, as in Alpine catchments, is highlighted.

Temporal and basin-specific population trends of quagga mussels on soft sediment of a multi-basin reservoir

Science.gov (United States)

Caldwell, Timothy J; Rosen, Michael R.; Chandra, Sudeep; Acharya, Kumud; Caires, Andrea M; Davis, Clinton J.; Thaw, Melissa; Webster, Daniel M.

2015-01-01

Invasive quagga (Dreissena bugnesis) and zebra (Dreissena ploymorpha) mussels have rapidly spread throughout North America. Understanding the relationships between environmental variables and quagga mussels during the early stages of invasion will help management strategies and allow researchers to predict patterns of future invasions. Quagga mussels were detected in Lake Mead, NV/AZ in 2007, we monitored early invasion dynamics in 3 basins (Boulder Basin, Las Vegas Bay, Overton Arm) bi-annually from 2008-2011. Mean quagga density increased over time during the first year of monitoring and stabilized for the subsequent two years at the whole-lake scale (8 to 132 individuals·m-2, geometric mean), in Boulder Basin (73 to 875 individuals·m-2), and in Overton Arm(2 to 126 individuals·m-2). In Las Vegas Bay, quagga mussel density was low (9 to 44 individuals·m-2), which was correlated with high sediment metal concentrations and warmer (> 30°C) water temperatures associated with that basin. Carbon content in the sediment increased with depth in Lake Mead and during some sampling periods quagga density was also positively correlated with depth, but more research is required to determine the significance of this interaction. Laboratory growth experiments suggested that food quantity may limit quagga growth in Boulder Basin, indicating an opportunity for population expansion in this basin if primary productivity were to increase, but was not the case in Overton Arm. Overall quagga mussel density in Lake Mead is highly variable and patchy, suggesting that temperature, sediment size, and sediment metal concentrations, and sediment carbon content all contribute to mussel distribution patterns. Quagga mussel density in the soft sediment of Lake Mead expanded during initial colonization, and began to stabilize approximately 3 years after the initial invasion.

Second workshop of I.A.G./A.I.G. SEDIBUD - Sediment Budgets in Cold Environments: Sediment fluxes and sediment budgets in changing high-latitude and high-altitude cold environments

Energy Technology Data Exchange (ETDEWEB)

Beylich, Achim A; Lamoureux, Scott F; Decaulne, Armelle

2007-07-01

This Second Workshop of the I.A.G./A.I.G. Working Group SEDIBUD (Sediment Budgets in Cold Environments) builds on four previous ESF SEDIFLUX Science Meetings held in Saudarkrokur (Iceland) in June 2004, Clermont-Ferrand (France) in January 2005, Durham (UK) in December 2005 and Trondheim (Norway) in the end of October/beginning of November 2006. A first kick-off Meeting of the new I.A.G./A.I.G. SEDIBUD Workshop. The theme of this Second I.A.G./A.I.G. SEDIBUD Workshop is Sediment FLuxes and Sediment Budgets in Changing High-Latitude Cold Environments. The Workshop is split between scientific paper and poster presentations, presentation and discussion of SEDIBUD key test sites, discussions within defined work groups and guided field trip to Kaerkevagge. This workshop will address the key aim of SEDIBUD to discuss Source-to-Sink-Fluxes and Sediment Budgets in Changing Cold Environments. Major emphasis will be given to consequences of climate change, scaling issues and source-to-sink correlations. Central issues will be presentation and discussion of the SEDIFLUX Manual (First Edition), the selection of SEDIBUD key test sites, the discussion and development of further ideas to extend the scientific activities within SEDIBUD in a global framework.(auth)

Cyclic Sediment Trading Between Channel and River Bed Sediments

Science.gov (United States)

Haddadchi, A.

2015-12-01

Much of the previous work on sediment tracing has focused on determining either the initial sources of the sediment (soils derive from a particular rock type) or the erosion processes generating the sediment. However, alluvial stores can be both a source and sink for sediment transported by streams. Here geochemical and fallout radionuclide tracing of river-bed and alluvial sediments are used to determine the role of secondary sources, sediment stores, as potential sources of sediment leaving Emu Creek catchment, southeastern Queensland, Australia. Activity concentrations of 137Cs on the river sediments are consistent with channel erosion being the dominant source at all sites sampled along the river. To characterise the deposition and remobilisation cycles in the catchment, a novel geochemical tracing approach was used. Successive pockets of alluvium were treated as discrete sink terms within geochemical mixing models and their source contributions compared with those of river bed sediments collected adjacent to each alluvial pocket. Three different size fractions were examined; silts and clays (banks indicates a high degree of 'trading' between the fluvial space and the alluvial space. Hence, management works aimed at primarily reducing the supply of sediments to the outlet of Emu Creek should focus on rehabilitation of channel banks in the lower catchment.

Test specification for decant pump and winch assembly

International Nuclear Information System (INIS)

Staehr, T.W.

1994-01-01

This specification provides the requirements for testing of the vertical turbine decant pump including the floating suction arm with load sensing winch control, instrumentation and the associated PLC/PC control system

Specification and Test of Real-Time Systems

DEFF Research Database (Denmark)

Nielsen, Brian

of the system, and a set of constraint patterns which describes and enforces the timing and synchronization constraints among components. We propose new techniques for automated black box conformance testing of real-time systems against densely timed speci cations. A test generator tool examines a specification......Distributed real-time computer based systems are very complex and intrinsically difficult to specify and implement correctly; in part this is caused by the overwhelming number of possible interactions between system components, but especially by a lack of adequate methods and tools to deal...... of the desired system behavior and generates the necessary test cases. A main problem is to construct a reasonably small test suite that can be executed within allotted resources, while having a high likelihood of detecting unknown errors. Our goal has been to treat the time dimension of this problem thoroughly...

Variation of a test's sensitivity and specificity with disease prevalence.

Science.gov (United States)

Leeflang, Mariska M G; Rutjes, Anne W S; Reitsma, Johannes B; Hooft, Lotty; Bossuyt, Patrick M M

2013-08-06

Anecdotal evidence suggests that the sensitivity and specificity of a diagnostic test may vary with disease prevalence. Our objective was to investigate the associations between disease prevalence and test sensitivity and specificity using studies of diagnostic accuracy. We used data from 23 meta-analyses, each of which included 10-39 studies (416 total). The median prevalence per review ranged from 1% to 77%. We evaluated the effects of prevalence on sensitivity and specificity using a bivariate random-effects model for each meta-analysis, with prevalence as a covariate. We estimated the overall effect of prevalence by pooling the effects using the inverse variance method. Within a given review, a change in prevalence from the lowest to highest value resulted in a corresponding change in sensitivity or specificity from 0 to 40 percentage points. This effect was statistically significant (p disease prevalence; there was no such systematic effect for sensitivity. The sensitivity and specificity of a test often vary with disease prevalence; this effect is likely to be the result of mechanisms, such as patient spectrum, that affect prevalence, sensitivity and specificity. Because it may be difficult to identify such mechanisms, clinicians should use prevalence as a guide when selecting studies that most closely match their situation.

Formal Specification Based Automatic Test Generation for Embedded Network Systems

Directory of Open Access Journals (Sweden)

Eun Hye Choi

2014-01-01

Full Text Available Embedded systems have become increasingly connected and communicate with each other, forming large-scaled and complicated network systems. To make their design and testing more reliable and robust, this paper proposes a formal specification language called SENS and a SENS-based automatic test generation tool called TGSENS. Our approach is summarized as follows: (1 A user describes requirements of target embedded network systems by logical property-based constraints using SENS. (2 Given SENS specifications, test cases are automatically generated using a SAT-based solver. Filtering mechanisms to select efficient test cases are also available in our tool. (3 In addition, given a testing goal by the user, test sequences are automatically extracted from exhaustive test cases. We’ve implemented our approach and conducted several experiments on practical case studies. Through the experiments, we confirmed the efficiency of our approach in design and test generation of real embedded air-conditioning network systems.

Permeability-Porosity Relationships of Subduction Zone Sediments

Science.gov (United States)

Gamage, K.; Screaton, E.; Bekins, B.; Aiello, I.

2008-12-01

Permeability-porosity relationships for sediments from Northern Barbados, Costa Rica, Nankai, and Peru subduction zones were examined based on their sediment type and grain size distribution. Greater correlation was observed between permeability and porosity for siliciclastic sediments, diatom oozes, and nannofossil chalk than for nannofossil oozes. For siliciclastic sediments, grouping of sediments by clay content yields relationships that are generally consistent with results from other marine settings and suggest decreasing permeability for a given porosity as clay content increases. Correction of measured porosities for smectite content generally improves the quality of permeability-porosity relationships. The relationship between permeability and porosity for diatom oozes may be controlled by the amount of clay present in the ooze, causing diatom oozes to behave similarly to siliciclastic sediments. For a given porosity the nannofossil oozes have higher permeability values by 1.5 orders of magnitude than the siliciclastic sediments. However, the use of a permeability-porosity relation may not be appropriate for unconsolidated carbonates such as nannofossil oozes. This study provided insight to the effects of porosity correction for smectite, variations in lithology and grain size in permeability-porosity relationships. However, further progress in delineating controls on permeability will require more careful and better documented permeability tests on characterized samples.

Drilling and testing specifications for the McGee well

International Nuclear Information System (INIS)

Patterson, J.K.

1982-01-01

The McGee Well is a part of the Basalt Waste Isolation Project's subsurface site selection and characterization activities. Information from the McGee Well support site hydrologic characterization and repository design. These test specifications include details for the drilling and testing of the McGee. It includes the predicted stratigraphy, the drilling requirements, description of tests to be conducted, intervals selected for hydrologic testing, and a schedule of the drilling and testing activities. 19 refs., 10 figs., 7 tabs

Toxicities and risk assessment of heavy metals in sediments of Taihu Lake, China, based on sediment quality guidelines.

Science.gov (United States)

Zhang, Yanfeng; Han, Yuwei; Yang, Jinxi; Zhu, Lingyan; Zhong, Wenjue

2017-12-01

The occurrence, toxicities, and ecological risks of five heavy metals (Pb, Cu, Cd, Zn and Ni) in the sediment of Taihu Lake were investigated in this study. To evaluate the toxicities caused by the heavy metals, the toxicities induced by organic contaminants and ammonia in the sediments were screened out with activated carbon and zeolite. The toxicities of heavy metals in sediments were tested with benthic invertebrates (tubificid and chironomid). The correlations between toxicity of sediment and the sediment quality guidelines (SQGs) derived previously were evaluated. There were significant correlations (pheavy metals based on SQGs, indicating that threshold effect level (TEL) and probable effect level (PEL) were reliable to predict the toxicities of heavy metals in the sediments of Taihu Lake. By contrast, the method based on acid volatile sulfides (AVS) and simultaneously extracted metals (SEM), such as ∑SEM/AVS and ∑SEM-AVS, did not show correlations with the toxicities. Moreover, the predictive ability of SQGs was confirmed by a total predicting accuracy of 77%. Ecological risk assessment based on TELs and PELs showed that the contaminations of Pb, Cu, Cd and Zn in the sediments of Taihu Lake were at relatively low or medium levels. The risks caused by heavy metals in the sediments of northern bay of the lake, which received more wastewater discharge from upper stream, were higher than other area of the lake. Copyright © 2017. Published by Elsevier B.V.

FARO tests corium-melt cooling in water pool: Roles of melt superheat and sintering in sediment

Energy Technology Data Exchange (ETDEWEB)

Hwang, Gisuk [Department of Mechanical Engineering, Wichita State University, Wichita, KS 67260 (United States); Kaviany, Massoud [Department of Mechanical Engineering, University of Michigan, Ann Arbor, MI 48109 (United States); Division of Advance Nuclear Engineering, POSTECH, Pohang, Gyeongbuk 790-784 (Korea, Republic of); Moriyama, Kiyofumi [Division of Advance Nuclear Engineering, POSTECH, Pohang, Gyeongbuk 790-784 (Korea, Republic of); Park, Hyun Sun, E-mail: hejsunny@postech.ac.kr [Division of Advance Nuclear Engineering, POSTECH, Pohang, Gyeongbuk 790-784 (Korea, Republic of); Hwang, Byoungcheol; Lee, Mooneon; Kim, Eunho; Park, Jin Ho [Division of Advance Nuclear Engineering, POSTECH, Pohang, Gyeongbuk 790-784 (Korea, Republic of); Nasersharifi, Yahya [Department of Mechanical Engineering, Wichita State University, Wichita, KS 67260 (United States)

2016-08-15

Highlights: • The numerical approach for FARO experimental data is suggested. • The cooling mechanism of ex-vessel corium is suggested. • The predicted minimum pool depth for no cake formation is suggested. - Abstract: The FARO tests have aimed at understanding an important severe accident mitigation action in a light water reactor when the accident progresses from the reactor pressure vessel boundary. These tests have aimed to measure the coolability of a molten core material (corium) gravity dispersed as jet into a water pool, quantifying the loose particle diameter distribution and fraction converted to cake under range of initial melt superheat and pool temperature and depth. Under complete hydrodynamic breakup of corium and consequent sedimentation in the pool, the initially superheated corium can result in debris bed consisting of discrete solid particles (loose debris) and/or a solid cake at the bottom of the pool. The success of the debris bed coolability requires cooling of the cake, and this is controlled by the large internal resistance. We postulate that the corium cake forms when there is a remelting part in the sediment. We show that even though a solid shell forms around the melt particles transiting in the water pool due to film-boiling heat transfer, the superheated melt allows remelting of the large particles in the sediment (depending on the water temperature and the transit time) using the COOLAP (Coolability Analysis with Parametric fuel-cooant interaction models) code. With this remelting and its liquid-phase sintering of the non-remelted particles, we predict the fraction of the melt particles converting to a cake through liquid sintering. Our predictions are in good agreement with the existing results of the FARO experiments. We address only those experiments with pool depths sufficient/exceeding the length required for complete breakup of the molten jet. Our analysis of the fate of molten corium aimed at devising the effective

Model testing of radioactive contamination by {sup 90}Sr, {sup 137}Cs and {sup 239,240}Pu of water and bottom sediments in the Techa River (Southern Urals, Russia)

Energy Technology Data Exchange (ETDEWEB)

Kryshev, I.I. [Scientific and Production Association ' Typhoon' , 82 Lenin Ave., Obninsk, Kaluga Region, 249038 (Russian Federation)], E-mail: ecomod@obninsk.com; Boyer, P.; Monte, L.; Brittain, J.E.; Dzyuba, N.N.; Krylov, A.L.; Kryshev, A.I.; Nosov, A.V.; Sanina, K.D.; Zheleznyak, M.I. [Scientific and Production Association ' Typhoon' , 82 Lenin Ave., Obninsk, Kaluga Region, 249038 (Russian Federation)

2009-03-15

This paper presents results of testing models for the radioactive contamination of river water and bottom sediments by {sup 90}Sr, {sup 137}Cs and {sup 239,240}Pu. The scenario for the model testing was based on data from the Techa River (Southern Urals, Russia), which was contaminated as a result of discharges of liquid radioactive waste into the river. The endpoints of the scenario were model predictions of the activity concentrations of {sup 90}Sr, {sup 137}Cs and {sup 239,240}Pu in water and bottom sediments along the Techa River in 1996. Calculations for the Techa scenario were performed by six participant teams from France (model CASTEAUR), Italy (model MARTE), Russia (models TRANSFER-2, CASSANDRA, GIDRO-W) and Ukraine (model RIVTOX), all using different models. As a whole, the radionuclide predictions for {sup 90}Sr in water for all considered models, {sup 137}Cs for MARTE and TRANSFER-2, and {sup 239,240}Pu for TRANSFER-2 and CASSANDRA can be considered sufficiently reliable, whereas the prediction for sediments should be considered cautiously. At the same time the CASTEAUR and RIVTOX models estimate the activity concentrations of {sup 137}Cs and {sup 239,240}Pu in water more reliably than in bottom sediments. The models MARTE ({sup 239,240}Pu) and CASSANDRA ({sup 137}Cs) evaluated the activity concentrations of radionuclides in sediments with about the same agreement with observations as for water. For {sup 90}Sr and {sup 137}Cs the agreement between empirical data and model predictions was good, but not for all the observations of {sup 239,240}Pu in the river water-bottom sediment system. The modelling of {sup 239,240}Pu distribution proved difficult because, in contrast to {sup 137}Cs and {sup 90}Sr, most of models have not been previously tested or validated for plutonium.

Assessing sediment contamination using six toxicity assays

Directory of Open Access Journals (Sweden)

Allen G. BURTON Jr.

2001-08-01

Full Text Available An evaluation of sediment toxicity at Lake Orta, Italy was conducted to compare a toxicity test battery of 6 assays and to evaluate the extent of sediment contamination at various sediment depths. Lake Orta received excessive loadings of copper and ammonia during the 1900’s until a large remediation effort was conducted in 1989-90 using lime addition. Since that time, the lake has shown signs of a steady recovery of biological communities. The study results showed acute toxicity still exists in sediments at a depth of 5 cm and greater. Assays that detected the highest levels of toxicity were two whole sediment exposures (7 d using Hyalella azteca and Ceriodaphnia dubia. The MicrotoxR assay using pore water was the third most sensitive assay. The Thamnotox, Rototox, Microtox solid phase, and Seed Germination-Root Elongation (pore and solid phase assays showed occasional to no toxicity. Based on similarity of responses and assay sensitivity, the two most useful assays were the C. dubia (or H. azteca and Microtox pore water. These assays were effective at describing sediment toxicity in a weight-of-evidence approach.

Linking nutrient enrichment, sediment erodibility and biofilms

Science.gov (United States)

Conrad, B.; Mahon, R.; Sojka, S. L.

2014-12-01

Sediment movement in coastal lagoons affects nutrient flux and primary producer growth. Previous research has shown that sediment erodibility is affected by biofilm concentration and that growth of benthic organisms, which produce biofilm, is affected by nutrient enrichment. However, researchers have not examined possible links between nutrient addition and sediment erodibility. We manipulated nutrient levels in the water column of 16 microcosms filled with homogenized sediment from a shallow coastal lagoon and artificial seawater to determine the effects on biofilm growth, measured through chlorophyll a and colloidal carbohydrate concentrations. Erosion tests using a Gust microcosm were conducted to determine the relationship between sediment erodibility and biofilm concentration. Results show that carbohydrate levels decreased with increasing nutrient enrichment and were unrelated to chlorophyll concentrations and erodibility. The nutrient levels did not predictably affect the chlorophyll levels, with lower chlorophyll concentrations in the control and medium enrichment treatments than the low and high enrichment treatments. Controls on biofilm growth are still unclear and the assumed relationship between carbohydrates and erodibility may be invalid. Understanding how biofilms respond to nutrient enrichment and subsequent effects on sediment erodibility is essential for protecting and restoring shallow coastal systems.

The assessment of sediment screening risk in Venice Lagoon and other coastal areas using international sediment quality guidelines

International Nuclear Information System (INIS)

Apitz, S.A.; Barbanti, A.; Bocci, M.; Delaney, E.; Bernstein, A.G.; Montobbio, L.

2007-01-01

A number of studies carried out in recent years have shown the presence of a wide range of contaminants in the Venice Lagoon. It is important to have a good understanding of the ecological quality of Venice Lagoon sediments, in order to: i) define and locate areas where a threat to the environment is present and therefore an intervention is needed (i.e. in situ assessment and management); and ii) define sustainable and environmentally correct ways of managing sediments which are to be dredged for navigational purposes or in relation to other interventions (i.e., ex situ management). Materials and Methods: To examine how various regional and international SQGs 'classed' screening risk in Venice Lagoon sediments, data on median contaminant levels in surface sediments in Venice Lagoon resulting from a literature review were compared to a range of local and international sediment quality guidelines (SQGs). Then data on sediment contaminant levels in various areas and sub-basins of Venice Lagoon (main Lagoon, Porto Marghera and Venice City Canals) and in other regional and international transitional and coastal ecosystems with various levels of human impact (urbanization and industrialization) were evaluated based upon a selected consensus-based SQG. Finally, screening sediment quality for all of Venice Lagoon was mapped and contoured, relative to this consensus-based SQG and briefly compared with direct toxicity measurement through a battery of bioassays. Results: SQGs allow the sediment areas to be put in terms of potential, or screening, risk. Although there were some differences depending upon which specific SQGs were applied, the Venice SQGs and other international SQGs provided the same general picture of screening risk in Venice Lagoon despite geographic differences. Venice Lagoon South has the lowest screening risk levels, Venice Lagoon Central/North has the highest (and is nearest to the Porto Marghera and Venice City Canals sites). Discussion: The Venice

Suspended sediment and sediment-associated contaminants in San Francisco Bay

Science.gov (United States)

Schoellhamer, D.H.; Mumley, T.E.; Leatherbarrow, J.E.

2007-01-01

Water-quality managers desire information on the temporal and spatial variability of contaminant concentrations and the magnitudes of watershed and bed-sediment loads in San Francisco Bay. To help provide this information, the Regional Monitoring Program for Trace Substances in the San Francisco Estuary (RMP) takes advantage of the association of many contaminants with sediment particles by continuously measuring suspended-sediment concentration (SSC), which is an accurate, less costly, and more easily measured surrogate for several trace metals and organic contaminants. Continuous time series of SSC are collected at several sites in the Bay. Although semidiurnal and diurnal tidal fluctuations are present, most of the variability of SSC occurs at fortnightly, monthly, and semiannual tidal time scales. A seasonal cycle of sediment inflow, wind-wave resuspension, and winnowing of fine sediment also is observed. SSC and, thus, sediment-associated contaminants tend to be greater in shallower water, at the landward ends of the Bay, and in several localized estuarine turbidity maxima. Although understanding of sediment transport has improved in the first 10 years of the RMP, determining a simple mass budget of sediment or associated contaminants is confounded by uncertainties regarding sediment flux at boundaries, change in bed-sediment storage, and appropriate modeling techniques. Nevertheless, management of sediment-associated contaminants has improved greatly. Better understanding of sediment and sediment-associated contaminants in the Bay is of great interest to evaluate the value of control actions taken and the need for additional controls. ?? 2007 Elsevier Inc. All rights reserved.

The Role of Prokaryotes in Sediment Carbon Cycling

DEFF Research Database (Denmark)

Piil, Kristoffer

in the sediment. In particular, the work has focused on estimating how rapidly amino acids derived from plankton are degraded and replaced by amino acids from prokaryotes and how extensive this reworking of amino acids is in surface sediments. Another part of my work has focused on establishing reliable estimates...... of cell specific amino acid and muramic acid concentrations in sediment bacteria. Such estimates are important tools when studying the reworking of amino acids by bacteria and the preservation of bacterial cell walls. In addition, it has been an aim of the work to investigate how abundant endospores...... are in marine sediment and how dynamic the endospore population is, as very little is known about this compartment of the prokaryotic community. Prokaryotic reworking of amino acids was investigated by two independent methods. The first approach involved estimating the amount of amino acids produced...

The contribution of bank and surface sediments to fluvial sediment ...

African Journals Online (AJOL)

The contribution of bank and surface sediments to fluvial sediment transport of the Pra River. ... the relative contribution of surface and bank sediments to the fluvial sediment transport. ... EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT

Novel speed test for evaluation of badminton-specific movements.

Science.gov (United States)

Madsen, Christian M; Karlsen, Anders; Nybo, Lars

2015-05-01

In this study, we developed a novel badminton-specific speed test (BST). The test was designed to mimic match play. The test starts in the center of the court and consists of 5 maximal actions to sensors located in each of the 4 corners of the court. The 20 actions are performed in randomized order as dictated by computer screen shots displayed 1 second after completion of the previous action. We assessed day-to-day variation in elite players, and specificity of the test was evaluated by comparing 30-m sprint performance and time to complete the BST in 20 elite players, 21 skilled players, and 20 age-matched physical active subjects (non-badminton players). Sprint performance was similar across groups, whereas the elite players were significantly (p ≤ 0.05) faster in the BST (total test time: 32.3 ± 1.1 seconds; average: 1.6 seconds per action) than the skilled (34.1 ± 2.0 seconds) and non-badminton players (35.7 ± 1.7 seconds). Day-to-day coefficient of variation (CV) of the BST was 0.7% for the elite players, whereas CV for repeated tests on the same day was 1.7% for elite, 2.6% for skilled, and 2.5% for non-badminton players. On this basis, we suggest that the BST may be valuable for evaluation of short-term maximal movement speed in badminton players. Thus, the BST seems to be sport specific, as it may discriminate between groups (elite, less trained players, and non-badminton players) with similar sprinting performance, and the low test-retest variation may allow for using the BST to evaluate longitudinal changes, for example, training effects or seasonal variations.

The sediments of the Venice Lagoon (Italy) evaluated in a screening risk assessment approach: part I--application of international sediment quality guidelines.

Science.gov (United States)

Apitz, Sabine E; Barbanti, Andrea; Bocci, Martina; Carlin, Anna; Montobbio, Laura; Bernstein, Alberto Giulio

2007-07-01

A number of studies carried out in recent years have shown the presence of a wide range of contaminants in the Venice Lagoon. It is important to have a good understanding of the ecological quality of Venice Lagoon sediments in order to 1) define and locate areas where a threat to the environment is present and therefore an intervention is needed (i.e., in situ assessment and management); and 2) define sustainable and environmentally correct ways of managing sediments that are to be dredged for navigational purposes or in relation to other interventions (i.e., ex situ management). This study reports on a critical comparison of chemical quality of sediments in Venice Lagoon and its subregions. Data on the Venice Lagoon were compiled from several studies conducted during the past decade on surface sediment contamination; temporal variation and risks for contaminants at depth were not addressed. The comparison of observed pollutant concentrations with local and internationally used sediment quality guidelines (SQGs) was used as a tool to benchmark different sites and for a tier I (screening) ecological risk assessment. Meaning and relevance of a number of SQGs are discussed, together with the options available for carrying out the comparison with sediment data. The screening of the Venice Lagoon sediment quality is discussed from a risk-assessment perspective and appropriate values for use in an in situ-ex situ management framework are suggested. Although there were some differences depending upon which specific SQGs were applied, different SQGs provided the same general picture of screening risk in Venice Lagoon: Although there are geographic differences, median levels for several contaminants in surface sediments exceeded a number of SQGs. Many contaminants exceed threshold effects SQGs, and Hg exceeds probable effects SQGs in most sub-basins except the southern Lagoon. Venice Lagoon south has the lowest screening risk levels, Venice Lagoon central/north has the

Effectiveness of bioremediation in reducing toxicity in oiled intertidal sediments

International Nuclear Information System (INIS)

Lee, K.; Tremblay, G.H.

1995-01-01

A 123-day field study was conducted with in situ enclosures to compare the effectiveness of bioremediation strategies based in inorganic and organic fertilizer additions to accelerate the biodegradation rates and reduce the toxicity of Venture trademark condensate stranded within sand-beach sediments. Comparison of the two fertilizer formulations with identical nitrogen and phosphorus concentrations showed that the organic fertilizer stimulated bacterial productivity within the oiled sediments to the greatest extent. However, detailed chemical analysis indicated that inorganic fertilizer additions were the most effective in enhancing condensate biodegradation rates. The Microtox reg-sign Solid-Phase Test (SPT) bioassay was determined to be sensitive to Venture Condensate in laboratory tests. Subsequent application of this procedure to oiled sediment in the field showed a reduction in sediment toxicity over time. However, the Microtox reg-sign bioassay procedure did not identify significant reductions in sediment toxicity following bioremediation treatment. An observed increase in toxicity following periodic additions of the organic fertilizer was attributed to rapid biodegradation rates of the fertilizer, which resulted in the production of toxic metabolic products

Shortened screening method for phosphorus fractionation in sediments A complementary approach to the standards, measurements and testing harmonised protocol

International Nuclear Information System (INIS)

Pardo, Patricia; Rauret, Gemma; Lopez-Sanchez, Jose Fermin

2004-01-01

The SMT protocol, a sediment phosphorus fractionation method harmonised and validated in the frame of the standards, measurements and testing (SMT) programme (European Commission), establishes five fractions of phosphorus according to their extractability. The determination of phosphate extracted is carried out spectrophotometrically. This protocol has been applied to 11 sediments of different origin and characteristics and the phosphorus extracted in each fraction was determined not only by UV-Vis spectrophotometry, but also by inductively coupled plasma-atomic emission spectrometry. The use of these two determination techniques allowed the differentiation between phosphorus that was present in the extracts as soluble reactive phosphorus and as total phosphorus. From the comparison of data obtained with both determination techniques a shortened screening method, for a quick evaluation of the magnitude and importance of the fractions given by the SMT protocol, is proposed and validated using two certified reference materials

Evaluation of Intake Efficiencies and Associated Sediment-Concentration Errors in US D-77 Bag-Type and US D-96-Type Depth-Integrating Suspended-Sediment Samplers

Science.gov (United States)

Sabol, T. A.; Topping, D. J.; Griffiths, R. E.

2011-12-01

Accurate measurements of suspended-sediment concentration require suspended-sediment samplers to operate isokinetically with an intake-efficiency of 1.0 ± 0.10. Results from 1940s Federal Interagency Sedimentation Project (FISP) laboratory experiments show that when the intake efficiency does not equal 1.0, suspended-sediment samplers either under- or oversample sediment relative to water, leading to biases in suspended-sediment concentration. The majority of recent FISP sampler development and testing has been conducted under uniform flow conditions using flume and slack-water tow tests, with little testing in actual turbulent rivers. Recent work has focused on the hydraulic characteristics and intake efficiencies of these samplers, without field investigations of the accuracy of the suspended-sediment data collected with these samplers. When depth-integrating suspended-sediment samplers are deployed under the non-uniform and turbulent conditions that exist in rivers, multiple factors may contribute to departures from isokinetic sampling. This introduces errors into the suspended-sediment data that may not be predictable on the basis of flume and tow tests alone. This study (1) evaluates the intake efficiencies of the older US D-77 bag-type and newer, FISP-approved US D-96 samplers at multiple river cross sections under a range of flow conditions; (2) examines if water temperature and sampling duration explain measured differences in intake efficiency between samplers and between laboratory and field tests; (3) models and predicts the directions and magnitudes of errors in measured suspended-sand concentration; and (4) determines if the relative differences in suspended-sediment concentration in a variety of size classes are consistent with the differences expected on the basis of the 1940s FISP-laboratory experiments. Results indicate that under river conditions, the intake efficiency of the US D-96 sampler is superior to that of the US D-77 bag-type sampler and

Optically stimulated luminescence dating of young sediments

DEFF Research Database (Denmark)

Madsen, Anni Tindahl; Murray, Andrew S.

2009-01-01

of OSL dating, outlines the problems specific to the dating of young material, and then uses recent applications to young sediments to illustrate the greatly increased scope and potential of the method in geomorphology and the geology of recent deposits. The overall reliability of this new generation...... for determining the time of deposition of water-lain sediments from the coastal zone, and aeolian deposits from both coastal and inland environments. Our conclusion is supported by the growing popularity of OSL dating in geomorphology and geology...

Characterization of trace organic contaminants in marine sediment from Yeongil Bay, Korea: 2. Dioxin-like and estrogenic activities

International Nuclear Information System (INIS)

Koh, Chul-Hwan; Khim, Jong Seong; Villeneuve, Daniel L.; Kannan, Kurunthachalam; Giesy, John P.

2006-01-01

This study employed mechanism-specific in vitro bioassays to help characterize the occurrence and distribution of dioxin-like and estrogenic contaminants in sediment from Yeongil Bay, Korea. Approximately 85% of the sediments tested induced significant dioxin-like activity in the H4IIE-luc bioassay, while approximately 50% induced significant estrogenic activity in the MVLN bioassay. Instrumentally-derived estimates of 2,3,7,8-tetrachlorodibenzo-p-dioxin and 17β-estradiol equivalents tended to underestimate the magnitude of response observed in the bioassays, suggesting that compounds detected by chemical analysis did not account for all the activity associated with Yeongil Bay sediments, or that non-additive interactions were occurring. The greatest dioxin-like and estrogenic activity was associated with the mid-polarity Florisil fractions (F2) expected to contain polycyclic aromatic hydrocarbons (PAHs) as well as chlorinated dioxins and furans. As in previous studies of Korean coastal sediment, more polar fractions (F3) generated more modest responses both in terms of magnitude and the number of samples responding. -- In vitro bioassay responses observed for Yeongil Bay surficial sediment and sediment core extracts showed the greatest dioxin-like and estrogenic activities in the mid-polarity fraction containing PAHs as well as chlorinated dioxins and furans

Assessing Sediment Yield and the Effect of Best Management Practices on Sediment Yield Reduction for Tutuila Island, American Samoa

Science.gov (United States)

Leta, O. T.; Dulai, H.; El-Kadi, A. I.

2017-12-01

of the impact that each BMP has on specific land use and Fagaalu's reef. It also offers information that may be useful for the coastal water resource management and mitigation measures to reduce sediment yield of the study site and similar areas.

Ocean floor sediment as a repository barrier: comparative diffusion data for selected radionuclides in sediments from the Atlantic and Pacific Oceans

International Nuclear Information System (INIS)

Schreiner, F.; Sabau, C.; Friedman, A.; Fried, S.

1986-01-01

Effective diffusion coefficients for selected radionuclides have been measured in ocean floor sediments to provide data for the assessment of barrier effectiveness in subseabed repositories for nuclear waste. The sediments tested include illite-rich and smectite-rich red clays from the mid plate gyre region of the Pacific Ocean, reducing sediment from the continental shelf of the northwest coast of North America, and Atlantic Ocean sediments from the Southern Nares Abyssal Plain and the Great Meteor East region. Results show extremely small effective diffusion coefficients with values less than 10 -14 m 2 s -1 for plutonium, americium, curium, thorium, and tin. Radionuclides with high diffusion coefficients of approximately 10 -10 m 2 s - include the anionic species pertechnetate, TcO 4 - , iodide, I - , and selenite, SO 3 -2 . Uranyl(VI) and neptunyl(V) ions, which are stable in solution, have diffusion coefficients around 10 -12 m 2 s -1 . The diffusion behavior of most radionuclides is similar in the oxygenated Pacific sediments and in the anoxic sediments from the Atlantic. An exception is neptunium, which is immobilized by Great Meteor East sediment, but has high mobility in Southern Nares Abyssal Plain sediment. Under stagnant conditions a 30 m thick sediment layer forms an effective geologic barrier isolating radionuclides in a subseabed repository from the biosphere

Ocean floor sediment as a repository barrier: comparative diffusion data for selected radionuclides in sediments from the Atlantic and Pacific Oceans

International Nuclear Information System (INIS)

Schreiner, F.; Sabau, C.; Friedman, A.; Fried, S.

1985-01-01

Effective diffusion coefficients for selected radionuclides have been measured in ocean floor sediments to provide data for the assessment of barrier effectiveness in subseabed repositories for nuclear waste. The sediments tested include illite-rich and smectite-rich red clays from the mid-plate gyre region of the Pacific Ocean, reducing sediment from the continental shelf of the northwest coast of North America, and Atlantic Ocean sediments from the Southern Nares Abyssal Plain and the Great Meteor East region. Results show extremely small effective diffusion coefficients with values less than 10 -14 m 2 s -1 for plutonium, americium, curium, thorium, and tin. Radionuclides with high diffusion coefficients of approximately 10 -10 m 2 s -1 include the anionic species pertechnetate, TcO 4 - , iodide, I - , and selenite, SeO 3 -2 . Uranyl(VI) and neptunyl(V) ions, which are stable in solution, have diffusion coefficients around 10 -12 m 2 s -1 . The diffusion behavior of most radionuclides is similar in the oxygenated Pacific sediments and in the anoxic sediments from the Atlantic. An exception is neptunium, which is immobilized by Great Meteor East sediment, but has high mobility in Southern Nares Abyssal Plain sediment. Under stagnant conditions a 30 m thick sediment layer forms an effective geologic barrier isolating radionuclides in a subseabed repository from the biosphere. 13 refs., 5 figs., 1 tab

Strength Estimation for Hydrate-Bearing Sediments From Direct Shear Tests of Hydrate-Bearing Sand and Silt

Science.gov (United States)

Liu, Zhichao; Dai, Sheng; Ning, Fulong; Peng, Li; Wei, Houzhen; Wei, Changfu

2018-01-01

Safe and economic methane gas production, as well as the replacement of methane while sequestering carbon in natural hydrate deposits, requires enhanced geomechanical understanding of the strength and volume responses of hydrate-bearing sediments during shear. This study employs a custom-made apparatus to investigate the mechanical and volumetric behaviors of carbon dioxide hydrate-bearing sediments subjected to direct shear. The results show that both peak and residual strengths increase with increased hydrate saturation and vertical stress. Hydrate contributes mainly the cohesion and dilatancy constraint to the peak strength of hydrate-bearing sediments. The postpeak strength reduction is more evident and brittle in specimens with higher hydrate saturation and under lower stress. Significant strength reduction after shear failure is expected in silty sediments with high hydrate saturation Sh ≥ 0.65. Hydrate contribution to the residual strength is mainly by increasing cohesion at low hydrate saturation and friction at high hydrate saturation. Stress state and hydrate saturation are dominating both the stiffness and the strength of hydrate-bearing sediments; thus, a wave velocity-based peak strength prediction model is proposed and validated, which allows for precise estimation of the shear strength of hydrate-bearing sediments through acoustic logging data. This method is advantageous to geomechanical simulators, particularly when the experimental strength data of natural samples are not available.

The NGDC Seafloor Sediment Geotechnical Database

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NGDC Seafloor Sediment Geotechnical Properties Database contains test engineering properties data coded by students at NGDC from primarily U.S. Naval...

Mobilization of radionuclides from sediments. Potential sources to Arctic waters

International Nuclear Information System (INIS)

Oughton, D.H.; Boerretzen, P.; Mathisen, B.; Salbu, B.; Tronstad, E.

1995-01-01

Contaminated soils and sediments can act as secondary sources of radionuclides to Arctic waters. In cases where the original source of contamination has ceased or been greatly reduced (e.g., weapons' testing, waste discharges from Mayak and Sellafield) remobilization of radionuclides from preciously contaminated sediments increases in importance. With respect to Arctic waters, potential secondary sources include sediments contaminated by weapons' testing, by discharges from nuclear installations to seawater, e.g., the Irish Sea, or by leakages from dumped waste containers. The major land-based source is run-off from soils and transport from sediments in the catchment areas of the Ob and Yenisey rivers, including those contaminated by Mayak discharges. Remobilization of radionuclides is often described as a secondary source of contamination. Whereas primary sources of man-made radionuclides tend to be point sources, secondary sources are usually more diffuse. Experiments were carried out on marine (Kara Sea, Irish Sea, Stepovogo and Abrosimov Fjords), estuarine (Ob-Yenisey) and dirty ice sediments. Total 137 Cs and 90 Sr concentrations were determined using standard radiochemical techniques. Tracer studies using 134 Cs and 85 Sr were used to investigate the kinetics of radionuclide adsorption and desorption. It is concluded that 90 Sr is much less strongly bound to marine sediments than 137 Cs, and can be chemically mobilized through ion exchange with elements is seawater. Radiocaesium is strongly and rapidly fixed to sediments. Discharges of 137 Cs to surface sediments (i.e., from dumped containers) would be expected to be retained in sediments to a greater extent than discharges to sea-waters. Physical mobilization of sediments, for example resuspension, may be of more importance for transport of 137 Cs than for 90 Sr. 7 refs., 4 figs

Bacterial metal resistance genes and metal bioavailability in contaminated sediments

International Nuclear Information System (INIS)

Roosa, Stéphanie; Wattiez, Ruddy; Prygiel, Emilie; Lesven, Ludovic; Billon, Gabriel; Gillan, David C.

2014-01-01

In bacteria a metal may be defined as bioavailable if it crosses the cytoplasmic membrane to reach the cytoplasm. Once inside the cell, specific metal resistance systems may be triggered. In this research, specific metal resistance genes were used to estimate metal bioavailability in sediment microbial communities. Gene levels were measured by quantitative PCR and correlated to metals in sediments using five different protocols to estimate dissolved, particle-adsorbed and occluded metals. The best correlations were obtained with czcA (a Cd/Zn/Co efflux pump) and Cd/Zn adsorbed or occluded in particles. Only adsorbed Co was correlated to czcA levels. We concluded that the measurement of czcA gene levels by quantitative PCR is a promising tool which may complement the classical approaches used to estimate Cd/Zn/Co bioavailability in sediment compartments. - Highlights: • Metal resistance genes were used to estimate metal bioavailability in sediments. • Gene levels were correlated to metals using 5 different metal extraction protocols. • CzcA gene levels determined by quantitative PCR is a promising tool for Cd/Zn/Co. - Capsule Bacterial czcA is a potential biomarker of Cd, Zn and Co bioavailability in aquatic sediments as shown by quantitative PCR and sequential metal extraction

Contaminants in stream sediments from seven United States metropolitan areas: part II—sediment toxicity to the amphipod Hyalella azteca and the midge Chironomus dilutus

Science.gov (United States)

Kemble, Nile E.; Hardesty, Douglas K.; Ingersoll, Christopher G.; Kunz, James L.; Sibley, Paul K.; Calhoun, Daniel L.; Gilliom, Robert J.; Kuivila, Kathryn; Nowell, Lisa H.; Moran, Patrick W.

2013-01-01

Relationships between sediment toxicity and sediment chemistry were evaluated for 98 samples collected from seven metropolitan study areas across the United States. Sediment-toxicity tests were conducted with the amphipod Hyalella azteca (28 day exposures) and with the midge Chironomus dilutus (10 day exposures). Overall, 33 % of the samples were toxic to amphipods and 12 % of the samples were toxic to midge based on comparisons with reference conditions within each study area. Significant correlations were observed between toxicity end points and sediment concentrations of trace elements, polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs), or organochlorine (OC) pesticides; however, these correlations were typically weak, and contaminant concentrations were usually below sediment-toxicity thresholds. Concentrations of the pyrethroid bifenthrin exceeded an estimated threshold of 0.49 ng/g (at 1 % total organic carbon) in 14 % of the samples. Of the samples that exceeded this bifenthrin toxicity threshold, 79 % were toxic to amphipods compared with 25 % toxicity for the samples below this threshold. Application of mean probable effect concentration quotients (PECQs) based on measures of groups of contaminants (trace elements, total PAHs, total PCBs,OCpesticides, and pyrethroid pesticides [bifenthrin in particular]) improved the correct classification of samples as toxic or not toxic to amphipods compared with measures of individual groups of contaminants. Sediments are a repository for many contaminants released into surface waters. Because of this, organisms inhabiting sediments may be exposed to a wide range of contaminants (United States Environmental Protection Agency (USEPA) United States Environmental Protection Agency 2000; American Society for Testing and Materials [ASTM] American Society for Testing and Materials International 2012). Contaminants of potential concern in sediments typically include trace elements (metals

Multiloop Integral System Test (MIST): MIST Facility Functional Specification

International Nuclear Information System (INIS)

Habib, T.F.; Koksal, C.G.; Moskal, T.E.; Rush, G.C.; Gloudemans, J.R.

1991-04-01

The Multiloop Integral System Test (MIST) is part of a multiphase program started in 1983 to address small-break loss-of-coolant accidents (SBLOCAs) specific to Babcock and Wilcox designed plants. MIST is sponsored by the US Nuclear Regulatory Commission, the Babcock ampersand Wilcox Owners Group, the Electric Power Research Institute, and Babcock and Wilcox. The unique features of the Babcock and Wilcox design, specifically the hot leg U-bends and steam generators, prevented the use of existing integral system data or existing integral facilities to address the thermal-hydraulic SBLOCA questions. MIST was specifically designed and constructed for this program, and an existing facility -- the Once Through Integral System (OTIS) -- was also used. Data from MIST and OTIS are used to benchmark the adequacy of system codes, such as RELAP5 and TRAC, for predicting abnormal plant transients. The MIST Functional Specification documents as-built design features, dimensions, instrumentation, and test approach. It also presents the scaling basis for the facility and serves to define the scope of work for the facility design and construction. 13 refs., 112 figs., 38 tabs

A pressure core ultrasonic test system for on-board analysis of gas hydrate-bearing sediments under in situ pressures.

Science.gov (United States)

Yang, Lei; Zhou, Weihua; Xue, Kaihua; Wei, Rupeng; Ling, Zheng

2018-05-01

The enormous potential as an alternative energy resource has made natural gas hydrates a material of intense research interest. Their exploration and sample characterization require a quick and effective analysis of the hydrate-bearing cores recovered under in situ pressures. Here a novel Pressure Core Ultrasonic Test System (PCUTS) for on-board analysis of sediment cores containing gas hydrates at in situ pressures is presented. The PCUTS is designed to be compatible with an on-board pressure core transfer device and a long gravity-piston pressure-retained corer. It provides several advantages over laboratory core analysis including quick and non-destructive detection, in situ and successive acoustic property acquisition, and remission of sample storage and transportation. The design of the unique assembly units to ensure the in situ detection is demonstrated, involving the U-type protecting jackets, transducer precession device, and pressure stabilization system. The in situ P-wave velocity measurements make the detection of gas hydrate existence in the sediments possible on-board. Performance tests have verified the feasibility and sensitivity of the ultrasonic test unit, showing the dependence of P-wave velocity on gas hydrate saturation. The PCUTS has been successfully applied for analysis of natural samples containing gas hydrates recovered from the South China Sea. It is indicated that on-board P-wave measurements could provide a quick and effective understanding of the hydrate occurrence in natural samples, which can assist further resource exploration, assessment, and subsequent detailed core analysis.

A pressure core ultrasonic test system for on-board analysis of gas hydrate-bearing sediments under in situ pressures

Science.gov (United States)

Yang, Lei; Zhou, Weihua; Xue, Kaihua; Wei, Rupeng; Ling, Zheng

2018-05-01

The enormous potential as an alternative energy resource has made natural gas hydrates a material of intense research interest. Their exploration and sample characterization require a quick and effective analysis of the hydrate-bearing cores recovered under in situ pressures. Here a novel Pressure Core Ultrasonic Test System (PCUTS) for on-board analysis of sediment cores containing gas hydrates at in situ pressures is presented. The PCUTS is designed to be compatible with an on-board pressure core transfer device and a long gravity-piston pressure-retained corer. It provides several advantages over laboratory core analysis including quick and non-destructive detection, in situ and successive acoustic property acquisition, and remission of sample storage and transportation. The design of the unique assembly units to ensure the in situ detection is demonstrated, involving the U-type protecting jackets, transducer precession device, and pressure stabilization system. The in situ P-wave velocity measurements make the detection of gas hydrate existence in the sediments possible on-board. Performance tests have verified the feasibility and sensitivity of the ultrasonic test unit, showing the dependence of P-wave velocity on gas hydrate saturation. The PCUTS has been successfully applied for analysis of natural samples containing gas hydrates recovered from the South China Sea. It is indicated that on-board P-wave measurements could provide a quick and effective understanding of the hydrate occurrence in natural samples, which can assist further resource exploration, assessment, and subsequent detailed core analysis.

INTERACTIONS AMONG PHOSPHATE AMENDMENTS, MICROBES AND URANIUM MOBILITY IN CONTAMINATED SEDIMENTS

Energy Technology Data Exchange (ETDEWEB)

Knox, A

2007-08-30

The use of sequestering agents for the transformation of radionuclides in low concentrations in contaminated soils/sediments offers considerable potential for long-term environmental cleanup. This study evaluated the influence of four phosphate amendments and two microbial amendments on U availability. The synchrotron X-ray fluorescence mapping of the untreated U-contaminated sediment showed that U was closely associated with Mn. All tested phosphate amendments reduced aqueous U concentration more than 90%, likely due to formation of insoluble phosphate precipitates. The addition of A. piechaudii and P. putida alone were found to reduce U concentrations 63% and 31% respectively. Uranium sorption in phosphate treatments was significantly reduced in the presence of microbes. However, increased microbial activity in the treated sediment led to reduction of phosphate effectiveness. The average U concentration in 1 M MgCl{sub 2} extract from U amended sediment was 437 {micro}g/kg, but in the same sediment without microbes (autoclaved sediment), the extractable U concentration was only 103 {micro}g/kg. When the autoclaved amended sediment was treated with autoclaved biological apatite, U concentration in the 1 M MgCl{sub 2} extract was {approx}0 {micro}g/kg. Together these tests suggest that microbes may enhance U leaching and reduce phosphate amendment remedial effectiveness.

Plutonium and americium in Lake Michigan sediments

International Nuclear Information System (INIS)

Edgington, D.N.; Alberts, J.J.; Wahlgren, M.A.; Karttunen, J.O.; Reeve, C.A.

1975-01-01

The vertical distributions of 239 , 240 Pu, 238 Pu, and 137 Cs have been measured in sediment cores taken from Lake Michigan. Sections from a limited number of cores have been analyzed for 241 Am. In addition, grab samples from ten locations in the southern basin of the lake have been analyzed for phase distribution of 239 , 240 Pu using a sequential extraction technique. The results indicate that the 239 , 240 Pu, 238 Pu, and 137 Cs from weapons testing, and the 241 Am formed in situ are concentrated in the sediments. A comparison of the total deposition of 239 , 240 Pu and 137 Cs indicates that 137 Cs may be valuable as a monitor for 239 , 240 Pu deposition in the sediments. Values of the 238 Pu/ 239 , 240 Pu ratio are in agreement with values reported in Lake Ontario sediments (and Lake Michigan plankton) and show little variation with depth. 241 Am data support the concept of in situ production with little preferential mobility after formation. Studies of sedimentary phase distributions show that 239 , 240 Pu is associated with hydrous oxide phases which are chemically stable under the prevailing conditions in lake sediments. Since Lake Michigan sediments remain aerobic, relatively little 239 , 240 Pu is available for chemical mobilization from the hydrous oxide or organic phases present in the sediments

Immobilization of cobalt by sulfate-reducing bacteria in subsurface sediments

Science.gov (United States)

Krumholz, Lee R.; Elias, Dwayne A.; Suflita, Joseph M.

2003-01-01

We investigated the impact of sulfate-reduction on immobilization of metals in subsurface aquifers. Co 2+ was used as a model for heavy metals. Factors limiting sulfate-reduction dependent Co 2+ immobilization were tested on pure cultures of sulfate-reducing bacteria, and in sediment columns from a landfill leachate contaminated aquifer. In the presence of 1 mM Co 2+ , the growth of pure cultures of sulfate-reducing bacteria was not impacted. Cultures of Desulfovibrio desulfuricans, Desulfotomaculum gibsoniae , and Desulfomicrobium hypogeia removed greater than 99.99% of the soluble Co 2+ when CoCl 2 was used with no chelators. The above cultures and Desulfoarcula baarsi removed 98-99.94% of the soluble Co(II) when the metal was complexed with the model ligand nitrilotriacetate (Co-NTA). Factors controlling the rate of sulfate-reduction based Co 2+ precipitation were investigated in sediment-cobalt mixtures. Several electron donors were tested and all but toluene accelerated soluble Co 2+ loss. Ethanol and formate showed the greatest stimulation. All complex nitrogen sources tested slowed and decreased the extent of Co 2+ removal from solution relative to formate-amended sediment incubations. A range of pH values were tested (6.35-7.81), with the more alkaline incubations exhibiting the largest precipitation of Co 2+ . The immobilization of Co 2+ in sediments was also investigated with cores to monitor the flow of Co 2+ through undisturbed sediments. An increase in the amount of Co 2+ immobilized as CoS was observed as sulfate reduction activity was stimulated in flow through columns. Both pure culture and sediment incubation data indicate that stimulation of sulfate reduction is a viable strategy in the immobilization of contaminating metals in subsurface systems.

Sediment studies at Bikini Atoll part 3. Inventories of some long-lived gamma-emitting radionuclides associated with lagoon surface sediments

Energy Technology Data Exchange (ETDEWEB)

Noshkin, V.E.

1997-12-01

Surface sediment samples were collected during 1979 from 87 locations in the lagoon at Bikini Atoll. The collections were made to better define the concentrations and distribution of long-lived radionuclides associated with the bottom material and to show what modifications occurred to the composition of the surface sediment from the nuclear testing program conducted by the United States at the Atoll between 1946 and 1958. This is the last of three reports on Bikini sediment studies. In this report, we discuss the concentrations and inventories of the residual long-lived gamma-emitting radionuclides in sediments from the lagoon. The gamma-emitting radionuclides detected most frequently in sediments collected in 1979, in addition to Americium-241 ({sup 241}Am) (discussed in the second report of this series), included Cesium-137 ({sup 137}Cs), Bismuth-207 ({sup 207}Bi), Europium-155 ({sup 155}Eu), and Cobalt-60 ({sup 60}Co). Other man-made, gamma-emitting radionuclides such as Europium-152,154 ({sup 152,154}Eu), Antimony-125 ({sup 125}Sb), and Rhodium-101,102m ({sup 101,102m}Rh) were occasionally measured above detection limits in sediments near test site locations. The mean inventories for {sup 137}Cs, {sup 207}Ei, {sup 155}Eu, and {sup 60}Co in the surface 4 cm of the lagoon sediment to be 1.7, 0.56, 7.76, and 0.74 TBq, respectively. By June 1997, radioactive decay would reduce these values to 1.1, 0.38, 0.62, and 0.07 TBq, respectively. Some additional loss results from a combination of different processes that continuously mobilize and return some amount of the radionuclides to the water column. The water and dissolved constituents are removed from the lagoon through channels and exchange with the surface waters of the north equatorial Pacific Ocean. Highest levels of these radionuclides are found in surface deposits lagoonward of the Bravo Crater. Lowest concentrations and inventories are associated with sediment lagoonward of the eastern reef. The quantities in

A universal approximation to grain size from images of non-cohesive sediment

Science.gov (United States)

Buscombe, D.; Rubin, D.M.; Warrick, J.A.

2010-01-01

The two-dimensional spectral decomposition of an image of sediment provides a direct statistical estimate, grid-by-number style, of the mean of all intermediate axes of all single particles within the image. We develop and test this new method which, unlike existing techniques, requires neither image processing algorithms for detection and measurement of individual grains, nor calibration. The only information required of the operator is the spatial resolution of the image. The method is tested with images of bed sediment from nine different sedimentary environments (five beaches, three rivers, and one continental shelf), across the range 0.1 mm to 150 mm, taken in air and underwater. Each population was photographed using a different camera and lighting conditions. We term it a “universal approximation” because it has produced accurate estimates for all populations we have tested it with, without calibration. We use three approaches (theory, computational experiments, and physical experiments) to both understand and explore the sensitivities and limits of this new method. Based on 443 samples, the root-mean-squared (RMS) error between size estimates from the new method and known mean grain size (obtained from point counts on the image) was found to be ±≈16%, with a 95% probability of estimates within ±31% of the true mean grain size (measured in a linear scale). The RMS error reduces to ≈11%, with a 95% probability of estimates within ±20% of the true mean grain size if point counts from a few images are used to correct bias for a specific population of sediment images. It thus appears it is transferable between sedimentary populations with different grain size, but factors such as particle shape and packing may introduce bias which may need to be calibrated for. For the first time, an attempt has been made to mathematically relate the spatial distribution of pixel intensity within the image of sediment to the grain size.

Geotechnical properties of deep-ocean sediments: a critical state approach

International Nuclear Information System (INIS)

Ho, E.W.L.

1988-11-01

The possible disposal of high-level radioactive waste using the sediments of the deep-ocean floor as repositories has initiated research to establish an understanding of the fundamental behaviour of deep-ocean sediments. The work described in this thesis consisted of a series of triaxial stress path tests using microcomputer controlled hydraulic triaxial cells to investigate the strength and stress-strain behaviour for mainly anisotropically (K o ) consolidated 'undisturbed' (tubed) and reconstituted specimens of deep-ocean sediments taken from two study areas in the North Atlantic Ocean. The test results have been analysed within the framework of critical state soil mechanics to investigate sediment characteristics such as the state boundary surface, drained and undrained strength and stress-strain behaviour. While marked anisotropic behaviour is found in a number of respects, the results indicate that analysis in a critical state framework is as valid as for terrestrial sediments. Differences in behaviour between tubed and reconstituted specimens have been observed and the effect of the presence of carbonate has been investigated. An attempt has been made to develop an elasto-plastic constitutive K o model based on critical state concepts. This model has been found to agree reasonably well with experimental data for kaolin and deep-ocean sediments. (author)

Sport specific fitness testing of elite badminton players.

Science.gov (United States)

Chin, M K; Wong, A S; So, R C; Siu, O T; Steininger, K; Lo, D T

1995-01-01

There is a scarcity of descriptive data on the performance capacity of elite badminton players, whose fitness requirements are quite specific. The purpose of this paper is to investigate the physiological response of elite badminton players in a sport-specific fitness test. Twelve Hong Kong national badminton team players performed a field test on a badminton court. Six light bulbs were connected to a programming device causing individual bulbs to light up in a given sequence. The players were instructed to react to the flashes by running towards them, and striking shuttles mounted in the vicinity of the bulbs. Exercise intensity was controlled by altering the interval between successive lightings. A low correlation (r = 0.65) was found between the results of the field test and the rank-order list of subjects, based on an objective on-field physiological assessment and subjective ranking. This may be explained by the requirements of other factors besides physical fitness which contribute to success in elite level badminton competition. These factors may include, for example, technical skill, mental power, and aesthetic judgements on the court. Maximum mean (s.d.) heart rate data (187(8) beats.min-1) and blood lactate values (10.4(2.9) mmol.l-1) in this study showed that players were under maximal load during the field test. From the testing data, it seems reasonable to speculate that the intensity of level 3 (20 light pulses.min-1; 3.0 s.pulse-1) and level 4 (22 light pulses.min-1; 2.7 s.pulse-1) simulates the requirement of actual games energy expenditure of the Hong Kong badminton players exercising at close to their anaerobic threshold. The results also show that an estimate of fitness can be derived from measurements involving exercise closely resembling that which is specific for the sports activity in question. Improved training advice and guidance may result from such studies. PMID:8800846

Use of the aquatic plant Elodea canadensis to assess toxicity and genotoxicity of Yenisei River sediments.

Science.gov (United States)

Zotina, Tatiana A; Trofimova, Elena A; Medvedeva, Marina Yu; Dementyev, Dmitry V; Bolsunovsky, Alexander Ya

2015-10-01

The toxicity, cytotoxicity, and genotoxicity of bulk sediments from the Yenisei River (Siberia, Russia) were estimated in laboratory bioassays based on several endpoints in the aquatic plant Elodea canadensis. The bottom sediment samples were collected in the Yenisei River upstream and downstream of the sources of chemical and radioactive contamination. The testing revealed different sensitivities of Elodea endpoints to the quality of the bottom sediment: weight of shoots Elodea) was the highest in sediments with chemical pollution, whereas the highest inhibition of toxicity endpoints (shoot and root length) occurred in sediments with the highest level of radioactive pollution. The extreme response of Elodea endpoints to the quality of certain sediment samples may be regarded as related to the possible presence of unknown toxicants. The results show that E. canadensis can be used as an indicator species in laboratory contact testing of bottom sediment. The responses of shoot and root length growth endpoints of Elodea can be recommended as basic sensitivity indicators of bottom sediment toxicity. Analysis of cells carrying abnormal chromosomes in the apical root meristem of Elodea can be performed optionally in the same test to assess the genotoxicity of sediments. © 2015 SETAC.

Geochemistry and toxicity of sediment porewater in a salt-impacted urban stormwater detention pond

International Nuclear Information System (INIS)

Mayer, T.; Rochfort, Q.; Borgmann, U.; Snodgrass, W.

2008-01-01

A comprehensive study was carried out to investigate the impacts of road salts on the benthic compartment of a small urban detention facility, Rouge River Pond. Although the pond is an engineered water body, it is representative of many small urban lakes, ponds and wetlands, which receive road runoff and are probable high impact areas. Specific objectives of the study were to document the porewater chemistry of an aquatic system affected by elevated salt concentrations and to carry out a toxicological assessment of sediment porewater to determine what factors may cause porewater toxicity. The results indicate that the sediment porewater may itself attain high salt concentrations. The computations show that increased chloride levels have important implications on the Cd complexation, augmenting its concentration in porewater. The toxicity tests suggest that the toxicity in porewater is caused by metals or other toxic chemicals, rather than high levels of chloride. - Effects of chlorides on metal chemistry and toxicity of sediment porewater in a stormwater detention pond impacted by road salts

Radiotracer Imaging of Sediment Columns

Science.gov (United States)

Moses, W. W.; O'Neil, J. P.; Boutchko, R.; Nico, P. S.; Druhan, J. L.; Vandehey, N. T.

2010-12-01

Nuclear medical PET and SPECT cameras routinely image radioactivity concentration of gamma ray emitting isotopes (PET - 511 keV; SPECT - 75-300 keV). We have used nuclear medical imaging technology to study contaminant transport in sediment columns. Specifically, we use Tc-99m (T1/2 = 6 h, Eγ = 140 keV) and a SPECT camera to image the bacteria mediated reduction of pertechnetate, [Tc(VII)O4]- + Fe(II) → Tc(IV)O2 + Fe(III). A 45 mL bolus of Tc-99m (32 mCi) labeled sodium pertechnetate was infused into a column (35cm x 10cm Ø) containing uranium-contaminated subsurface sediment from the Rifle, CO site. A flow rate of 1.25 ml/min of artificial groundwater was maintained in the column. Using a GE Millennium VG camera, we imaged the column for 12 hours, acquiring 44 frames. As the microbes in the sediment were inactive, we expected most of the iron to be Fe(III). The images were consistent with this hypothesis, and the Tc-99m pertechnetate acted like a conservative tracer. Virtually no binding of the Tc-99m was observed, and while the bolus of activity propagated fairly uniformly through the column, some inhomogeneity attributed to sediment packing was observed. We expect that after augmentation by acetate, the bacteria will metabolically reduce Fe(III) to Fe(II), leading to significant Tc-99m binding. Imaging sediment columns using nuclear medicine techniques has many attractive features. Trace quantities of the radiolabeled compounds are used (micro- to nano- molar) and the half-lives of many of these tracers are short (Image of Tc-99m distribution in a column containing Rifle sediment at four times.

Strontium-90 in the bottom sediments of some Finnish lakes

Energy Technology Data Exchange (ETDEWEB)

Ilus, E.; Puhakainen, M.; Saxen, R

1999-07-01

The {sup 90}Sr concentrations in surface waters varied from 14 to 29 Bq m{sup -3} in 1988 and from 16 to 23 Bq m{sup -3} in 1990. In Lake Pielinen almost all the {sup 90}Sr seemed to originate from weapons test fallout, whereas in Lakes Ontojaervi, Naesijaervi and Pyhaejaervi the share of the Chernobyl fallout was equal to that of weapons test fallout. In the sediments, the total amount of {sup 90}Sr per square metre varied from 97 to 1060 Bq m{sup -2} in 1988 and from 310 to 1160 Bq m{sup -2} in 1990. The maximum values occurred in Lake Naesijaervi. The local amount of deposition and the type of sediment were the most important factors affecting strontium values in sediments. In addition, the large variation in total amounts of {sup 90}Sr was due to other environmental factors. The total amounts of {sup 90}Sr in sediments were generally of the same order of magnitude as the {sup 90}Sr deposition on the ground in the area. The concentrations of {sup 90}Sr in surface waters also conformed quite well to the distribution pattern of the deposition values. At some stations there was a clear maximum in a deeper sediment layer, which could be construed as a marker of the nuclear weapons tests in the 1960s. (orig.)

Tracking variable sedimentation rates in orbitally forced paleoclimate proxy series

Science.gov (United States)

Li, M.; Kump, L. R.; Hinnov, L.

2017-12-01

This study addresses two fundamental issues in cyclostratigraphy: quantitative testing of orbital forcing in cyclic sedimentary sequences and tracking variable sedimentation rates. The methodology proposed here addresses these issues as an inverse problem, and estimates the product-moment correlation coefficient between the frequency spectra of orbital solutions and paleoclimate proxy series over a range of "test" sedimentation rates. It is inspired by the ASM method (1). The number of orbital parameters involved in the estimation is also considered. The method relies on the hypothesis that orbital forcing had a significant impact on the paleoclimate proxy variations, and thus is also tested. The null hypothesis of no astronomical forcing is evaluated using the Beta distribution, for which the shape parameters are estimated using a Monte Carlo simulation approach. We introduce a metric to estimate the most likely sedimentation rate using the product-moment correlation coefficient, H0 significance level, and the number of contributing orbital parameters, i.e., the CHO value. The CHO metric is applied with a sliding window to track variable sedimentation rates along the paleoclimate proxy series. Two forward models with uniform and variable sedimentation rates are evaluated to demonstrate the robustness of the method. The CHO method is applied to the classical Late Triassic Newark depth rank series; the estimated sedimentation rates match closely with previously published sedimentation rates and provide a more highly time-resolved estimate (2,3). References: (1) Meyers, S.R., Sageman, B.B., Amer. J. Sci., 307, 773-792, 2007; (2) Kent, D.V., Olsen, P.E., Muttoni, G., Earth-Sci. Rev.166, 153-180, 2017; (3) Li, M., Zhang, Y., Huang, C., Ogg, J., Hinnov, L., Wang, Y., Zou, Z., Li, L., 2017. Earth Plant. Sc. Lett. doi:10.1016/j.epsl.2017.07.015

Temperature signal in suspended sediment export from an Alpine catchment

Science.gov (United States)

Costa, Anna; Molnar, Peter; Stutenbecker, Laura; Bakker, Maarten; Silva, Tiago A.; Schlunegger, Fritz; Lane, Stuart N.; Loizeau, Jean-Luc; Girardclos, Stéphanie

2018-01-01

Suspended sediment export from large Alpine catchments ( > 1000 km2) over decadal timescales is sensitive to a number of factors, including long-term variations in climate, the activation-deactivation of different sediment sources (proglacial areas, hillslopes, etc.), transport through the fluvial system, and potential anthropogenic impacts on the sediment flux (e.g. through impoundments and flow regulation). Here, we report on a marked increase in suspended sediment concentrations observed near the outlet of the upper Rhône River Basin in the mid-1980s. This increase coincides with a statistically significant step-like increase in basin-wide mean air temperature. We explore the possible explanations of the suspended sediment rise in terms of changes in water discharge (transport capacity), and the activation of different potential sources of fine sediment (sediment supply) in the catchment by hydroclimatic forcing. Time series of precipitation and temperature-driven snowmelt, snow cover, and ice melt simulated with a spatially distributed degree-day model, together with erosive rainfall on snow-free surfaces, are tested to explore possible reasons for the rise in suspended sediment concentration. We show that the abrupt change in air temperature reduced snow cover and the contribution of snowmelt, and enhanced ice melt. The results of statistical tests show that the onset of increased ice melt was likely to play a dominant role in the suspended sediment concentration rise in the mid-1980s. Temperature-driven enhanced melting of glaciers, which cover about 10 % of the catchment surface, can increase suspended sediment yields through an increased contribution of sediment-rich glacial meltwater, increased sediment availability due to glacier recession, and increased runoff from sediment-rich proglacial areas. The reduced extent and duration of snow cover in the catchment are also potential contributors to the rise in suspended sediment concentration through

Quality Assurance Project Plan for Verification of Sediment Ecotoxicity Assessment Ring(SEA Ring)

Science.gov (United States)

The objective of the verification is to test the efficacy and ability of the Sediment Ecotoxicity Assessment Ring (SEA Ring) to evaluate the toxicity of contaminants in the sediment, at the sediment-water interface, and WC to organisms that live in those respective environments.

Decontamination and functional reclamation of dredged brackish sediments.

Science.gov (United States)

Doni, S; Macci, C; Peruzzi, E; Iannelli, R; Ceccanti, B; Masciandaro, G

2013-07-01

The continuous stream of sediments, dredged from harbors and waterways for keeping shipping traffic efficiency, is a considerable ongoing problem recognized worldwide. This problem gets worse as most of the sediments dredged from commercial ports and waterways turn out to be polluted by a wide range of organic and inorganic contaminants. In this study, phytoremediation was explored as a sustainable reclamation technology for turning slightly-polluted brackish dredged sediments into a matrix feasible for productive use. To test this possibility, a phytoremediation experimentation was carried out in containers of about 0.7 m(3) each, filled with brackish dredged sediments contaminated by heavy metals and hydrocarbons. The sediments were pre-conditioned by adding an agronomic soil (30 % v/v) to improve their clayey granulometric composition, and by topping the mixture with high quality compost (4 kg m(-2)) to favour the initial adaptation of the selected vegetal species. The following plant treatments were tested: (1) Paspalum vaginatum, (2) Phragmites australis, (3) Spartium junceum + P. vaginatum, (4) Nerium oleander + P. vaginatum, (5) Tamarix gallica + P. vaginatum, and (6) unplanted control. Eighteen months after the beginning of the experimentation, all the plant species were found in healthy condition and well developed. Throughout the whole experiment, the monitored biological parameters (total microbial population and dehydrogenase activity) were generally observed as constantly increasing in all the planted sediments more than in the control, pointing out an improvement of the chemico-physical conditions of both microorganisms and plants. The concentration decrease of organic and inorganic contaminants (>35 and 20 %, respectively) in the treatments with plants, particularly in the T. gallica + P. vaginatum, confirmed the importance of the root-microorganism interaction in activating the decontamination processes. Finally, the healthy state of

The impact of sediment bioturbation by secondary organisms on metal bioavailability, bioaccumulation and toxicity to target organisms in benthic bioassays: Implications for sediment quality assessment

International Nuclear Information System (INIS)

Remaili, Timothy M.; Simpson, Stuart L.; Amato, Elvio D.; Spadaro, David A.; Jarolimek, Chad V.; Jolley, Dianne F.

2016-01-01

Bioturbation alters the properties of sediments and modifies contaminant bioavailability to benthic organisms. These naturally occurring disturbances are seldom considered during the assessment of sediment quality. We investigated how the presence (High bioturbation) and absence (Low bioturbation) of a strongly bioturbating amphipod within three different sediments influenced metal bioavailability, survival and bioaccumulation of metals to the bivalve Tellina deltoidalis. The concentrations of dissolved copper decreased and manganese increased with increased bioturbation. For copper a strong correlation was observed between increased bivalve survival (53–100%) and dissolved concentrations in the overlying water. Increased bioturbation intensity resulted in greater tissue concentrations for chromium and zinc in some test sediments. Overall, the results highlight the strong influence that the natural bioturbation activities from one organism may have on the risk contaminants pose to other organisms within the local environment. The characterisation of field-based exposure conditions concerning the biotic or abiotic resuspension of sediments and the rate of attenuation of released contaminants through dilution or readsorption may enable laboratory-based bioassay designs to be adapted to better match those of the assessed environment. - Highlights: • Bioturbation intensity modifies metal exposure and outcomes of sediment bioassays. • Sediment fluxes of Cu decrease and Mn and Zn increase with increased bioturbation. • Strong correlations between bioaccumulated and dissolved Cd, Cr, Pb, Zn, Cu and Ni. • Weak correlations between bioaccumulated and particulate metals. - This study investigated the impact of sediment bioturbation intensity on metal bioavailability and toxicity to aquatic organisms, and the implications of this to toxicity test design.

What are the contemporary sources of sediment in the Mississippi River?

Science.gov (United States)

Hassan, M. A.; Roberge, L.; Church, M.; More, M.; Donner, S. D.; Leach, J.; Ali, K. F.

2017-09-01

Within the last two centuries, the Mississippi River basin has been transformed by changes in land use practices, dam construction, and training of the rivers for navigation. Here we analyze the contemporary patterns of fluvial sediment yield in the Mississippi River basin using all available data in order to assess the influence of regional land condition on the variation of sediment yield within the basin. We develop regional-scale relations between specific sediment yield (yield per unit area) and drainage area to reveal contemporary regional sediment yield patterns and source areas of riverine sediments. Extensive upland erosion before the development of soil conservation practices exported large amounts of sediment to the valleys and floodplains. We show that sediment today is sourced primarily along the river valleys from arable land, and from stream bank and channel erosion, with sediment yields from areas dominated by arable land 2 orders of magnitude greater than that of grassland dominated areas. Comparison with the "T factor," a commonly quoted measure of agricultural soil resilience suggests that the latter may not reflect contemporary soil loss from the landscape.

Vertical jumping tests in volleyball: reliability, validity, and playing-position specifics.

Science.gov (United States)

Sattler, Tine; Sekulic, Damir; Hadzic, Vedran; Uljevic, Ognjen; Dervisevic, Edvin

2012-06-01

Vertical jumping is known to be important in volleyball, and jumping performance tests are frequently studied for their reliability and validity. However, most studies concerning jumping in volleyball have dealt with standard rather than sport-specific jumping procedures and tests. The aims of this study, therefore, were (a) to determine the reliability and factorial validity of 2 volleyball-specific jumping tests, the block jump (BJ) test and the attack jump (AJ) test, relative to 2 frequently used and systematically validated jumping tests, the countermovement jump test and the squat jump test and (b) to establish volleyball position-specific differences in the jumping tests and simple anthropometric indices (body height [BH], body weight, and body mass index [BMI]). The BJ was performed from a defensive volleyball position, with the hands positioned in front of the chest. During an AJ, the players used a 2- to 3-step approach and performed a drop jump with an arm swing followed by a quick vertical jump. A total of 95 high-level volleyball players (all men) participated in this study. The reliability of the jumping tests ranged from 0.97 to 0.99 for Cronbach's alpha coefficients, from 0.93 to 0.97 for interitem correlation coefficients and from 2.1 to 2.8 for coefficients of variation. The highest reliability was found for the specific jumping tests. The factor analysis extracted one significant component, and all of the tests were highly intercorrelated. The analysis of variance with post hoc analysis showed significant differences between 5 playing positions in some of the jumping tests. In general, receivers had a greater jumping capacity, followed by libero players. The differences in jumping capacities should be emphasized vis-a-vis differences in the anthropometric measures of players, where middle hitters had higher BH and body weight, followed by opposite hitters and receivers, with no differences in the BMI between positions.

Comparison. US P-61 and Delft sediment samplers

Science.gov (United States)

Beverage, Joseph P.; Williams, David T.

1990-01-01

The Delft Bottle (DB) is a flow-through device designed by the Delft Hydraulic Laboratory (DHL), The Netherlands, to sample sand-sized sediment suspended in streams. The US P-61 sampler was designed by the Federal Interagency Sedimentation Project (FISP) at the St. Anthony Falls Hydraulic Laboratory, Minneapolis, Minnesota, to collect suspended sediment from deep, swift rivers. The results of two point-sampling tests in the United States, the Mississippi River near Vicksburg, Mississippi, in 1983 and the Colorado River near Blythe, California, in 1984, are provided in this report. These studies compare sand-transport rates, rather than total sediment-transport rates, because fine material washes through the DB sampler. In the United States, the commonly used limits for sand-sized material are 0.062 mm to 2.00 mm (Vanoni 1975).

Effects of engineered nano-titanium dioxide on pore surface properties and phosphorus adsorption of sediment: Its environmental implications

International Nuclear Information System (INIS)

Luo, Zhuanxi; Wang, Zhenhong; Wei, QunShan; Yan, Changzhou; Liu, Feng

2011-01-01

Highlights: → The attachment of Enano-TiO 2 to surface enhanced markedly sediment BET surface area and t-Plot external surface area. → The fill of Enano-TiO 2 into the micropores reduced significantly the sediment t-Plot micropore surface area. → Enano-TiO 2 could increase sediment phosphorus (P) adsorption maximum and decrease in sediment P binding energy. → P would be easily released because of the decreasing P binding energy of the sediment with elevated Enano-TiO 2 . - Abstract: Understanding the environmental safety and human health implications of engineered nanoparticles (ENPs) is of worldwide importance. As an important ENPs, engineered nano-TiO 2 (Enano-TiO 2 ) may have been substantially deposited in aquatic sediments because of its widely uses. Sediment pore surface properties would be thus significantly influenced due to the large surface area of Enano-TiO 2 . In this study, Enano-TiO 2 was found to greatly impact on sediment pore surface properties. The attachment of Enano-TiO 2 particles to sediment surfaces enhanced markedly BET specific surface area and t-Plot external specific surface area, and thereby increased sediment phosphorus (P) adsorption maximum (S max ). Contrarily, the fill of Enano-TiO 2 particles into the micropores of sediments could significantly reduce t-Plot micropore specific surface area, and cause slight decrease in sediment P binding energy (K). Clearly, P sorbed in sediment would be easily released because of the decreasing P binding energy of the sediment with elevated Enano-TiO 2 . Enano-TiO 2 would thus cause aggravated endogenous pollution in water if such sediment was re-suspended on disturbance. The results obtained in this study contribute to our increasing knowledge of how to regulate physicochemical behavior of pollutants in sediments under the influences of Enano-TiO 2 and/or similar ENPs.

The influence of grain size, grain color, and suspended-sediment concentration on light attenuation: why fine-grained terrestrial sediment is bad for coral reef ecosystems

Science.gov (United States)

Storlazzi, Curt; Norris, Benjamin; Rosenberger, Kurt

2015-01-01

Sediment has been shown to be a major stressor to coral reefs globally. Although many researchers have tested the impact of sedimentation on coral reef ecosystems in both the laboratory and the field and some have measured the impact of suspended sediment on the photosynthetic response of corals, there has yet to be a detailed investigation on how properties of the sediment itself can affect light availability for photosynthesis. We show that finer-grained and darker-colored sediment at higher suspended-sediment concentrations attenuates photosynthetically active radiation (PAR) significantly more than coarser, lighter-colored sediment at lower concentrations and provide PAR attenuation coefficients for various grain sizes, colors, and suspended-sediment concentrations that are needed for biophysical modeling. Because finer-grained sediment particles settle more slowly and are more susceptible to resuspension, they remain in the water column longer, thus causing greater net impact by reducing light essential for photosynthesis over a greater duration. This indicates that coral reef monitoring studies investigating sediment impacts should concentrate on measuring fine-grained lateritic and volcanic soils, as opposed to coarser-grained siliceous and carbonate sediment. Similarly, coastal restoration efforts and engineering solutions addressing long-term coral reef ecosystem health should focus on preferentially retaining those fine-grained soils rather than coarse silt and sand particles.

Sediment supply versus local hydraulic controls on sediment transport and storage in a river with large sediment loads

Science.gov (United States)

Dean, David; Topping, David; Schmidt, John C.; Griffiths, Ronald; Sabol, Thomas

2016-01-01

The Rio Grande in the Big Bend region of Texas, USA, and Chihuahua and Coahuila, Mexico, undergoes rapid geomorphic changes as a result of its large sediment supply and variable hydrology; thus, it is a useful natural laboratory to investigate the relative importance of flow strength and sediment supply in controlling alluvial channel change. We analyzed a suite of sediment transport and geomorphic data to determine the cumulative influence of different flood types on changing channel form. In this study, physically based analyses suggest that channel change in the Rio Grande is controlled by both changes in flow strength and sediment supply over different spatial and temporal scales. Channel narrowing is primarily caused by substantial deposition of sediment supplied to the Rio Grande during tributary-sourced flash floods. Tributary floods have large suspended-sediment concentrations, occur for short durations, and attenuate rapidly downstream in the Rio Grande, depositing much of their sediment in downstream reaches. Long-duration floods on the mainstem have the capacity to enlarge the Rio Grande, and these floods, released from upstream dams, can either erode or deposit sediment in the Rio Grande depending upon the antecedent in-channel sediment supply and the magnitude and duration of the flood. Geomorphic and sediment transport analyses show that the locations and rates of sand erosion and deposition during long-duration floods are most strongly controlled by spatial changes in flow strength, largely through changes in channel slope. However, spatial differences in the in-channel sediment supply regulate sediment evacuation or accumulation over time in long reaches (greater than a kilometer).

Experimental test of host specificity in a behaviour-modifying trematode

DEFF Research Database (Denmark)

Hernandez, R.N.; Fredensborg, Brian Lund

2015-01-01

Host behavioural modification by parasites is a common and well-documented phenomenon. However, knowledge on the complexity and specificity of the underlying mechanisms is limited, and host specificity among manipulating parasites has rarely been experimentally verified. We tested the hypothesis...

Sediment transfer dynamics in the Illgraben

Science.gov (United States)

Bennett, G. L.; Molnar, P.; McArdell, B. W.; Schlunegger, F.; Burlando, P.

2012-04-01

resumed. During this time hillslope erosion exceeded channel erosion by 0.14myr¯ 1 indicating that hillslopes eroded independently of channel incision. Channel sediment transfer was transport-limited at the scale of the study as suggested by the aggradation of the channel in periods of very high hillslope flux and its apparent relation to variables connected to runoff generation such as precipitation and snowmelt. We have developed a conceptual model of sediment transfer based on our data set with which to investigate sediment transfer dynamics in a probabilistic sense. A stochastic sediment input from the hillslopes is generated from our magnitude-frequency model of landslides. Sediment is fed into a hillslope storage component, where a fraction is redeposited in long-term storage. Sediment in short-term storage is subsequently fed into the channel system and is only removed given a transport event (rainfall or snowmelt) of sufficient magnitude and sufficient available sediment. Transport events are generated stochastically using a weather generator. We calibrate the model with available data. Despite its simplicity the model reproduces the storage and discharge behavior of the channel system observed over the study period and enables us to test the sensitivity of the system to different parameters and system structures.

Ocean floor sediment as a repository barrier: comparative diffusion data for selected radionuclides in sediments from the Atlantic and Pacific Oceans

Energy Technology Data Exchange (ETDEWEB)

Schreiner, F.; Sabau, C.; Friedman, A.; Fried, S.

1985-01-01

Effective diffusion coefficients for selected radionuclides have been measured in ocean floor sediments to provide data for the assessment of barrier effectiveness in subseabed repositories for nuclear waste. The sediments tested include illite-rich and smectite-rich red clays from the mid-plate gyre region of the Pacific Ocean, reducing sediment from the continental shelf of the northwest coast of North America, and Atlantic Ocean sediments from the Southern Nares Abyssal Plain and the Great Meteor East region. Results show extremely small effective diffusion coefficients with values less than 10/sup -14/ m/sup 2/s/sup -1/ for plutonium, americium, curium, thorium, and tin. Radionuclides with high diffusion coefficients of approximately 10/sup -10/ m/sup 2/s/sup -1/ include the anionic species pertechnetate, TcO/sub 4//sup -/, iodide, I/sup -/, and selenite, SeO/sub 3//sup -2/. Uranyl(VI) and neptunyl(V) ions, which are stable in solution, have diffusion coefficients around 10/sup -12/ m/sup 2/s/sup -1/. The diffusion behavior of most radionuclides is similar in the oxygenated Pacific sediments and in the anoxic sediments from the Atlantic. An exception is neptunium, which is immobilized by Great Meteor East sediment, but has high mobility in Southern Nares Abyssal Plain sediment. Under stagnant conditions a 30 m thick sediment layer forms an effective geologic barrier isolating radionuclides in a subseabed repository from the biosphere. 13 refs., 5 figs., 1 tab.

Simulating Landscape Sediment Transport Capacity by Using a Modified SWAT Model.

Science.gov (United States)

Bonumá, Nadia B; Rossi, Colleen G; Arnold, Jeffrey G; Reichert, José M; Minella, Jean P; Allen, Peter M; Volk, Martin

2014-01-01

Sediment delivery from hillslopes to rivers is spatially variable and may lead to long-term delays between initial erosion and related sediment yield at the watershed outlet. Consideration of spatial variability is important for developing sound strategies for water quality improvement and soil protection at the watershed scale. Hence, the Soil and Water Assessment Tool (SWAT) was modified and tested in this study to simulate the landscape transport capacity of sediment. The study area was the steeply sloped Arroio Lino watershed in southern Brazil. Observed sediment yield data at the watershed outlet were used to calibrate and validate a modified SWAT model. For the calibration period, the modified model performed better than the unaltered SWAT2009 version; the models achieved Nash-Sutcliffe efficiency (NSE) values of 0.7 and -0.1, respectively. Nash-Sutcliffe efficiencies were less for the validation period, but the modified model's NSE was higher than the unaltered model (-1.4 and -12.1, respectively). Despite the relatively low NSE values, the results of this first test are promising because the model modifications lowered the percent bias in sediment yield from 73 to 18%. Simulation results for the modified model indicated that approximately 60% of the mobilized soil is deposited along the landscape before it reaches the river channels. This research demonstrates the modified model's ability to simulate sediment yield in watersheds with steep slopes. The results suggest that integration of the sediment deposition routine in SWAT increases accuracy in steeper areas while significantly improving its ability to predict the spatial distribution of sediment deposition areas. Further work is needed regarding (i) improved strategies for spatially distributed sediment transport measurements (for improving process knowledge and model evaluation) and (ii) extensive model tests in other well instrumented experimental watersheds with differing topographic configurations

Test specification for decant pump and winch assembly. Revision 2

International Nuclear Information System (INIS)

Staehr, T.W.

1995-01-01

This specification provides the requirements for testing of the vertical turbine decant pump including the floating suction with load sensing winch control, instrumentation and the associated PLC/PC control system. All assembly necessary for testing including piping, temporary wiring, etc., shall be performed by the Seller. All referenced figures are at the back of this document. The testing consists of performance testing, winch testing and calibration, instrumentation verification testing and run-in testing of the pump. Testing shall be done in the presence and under the direction of the Buyer in accordance with this procedure

Towards science-based sediment quality standards—Effects of field-collected sediments in rainbow trout (Oncorhynchus mykiss)

International Nuclear Information System (INIS)

Brinkmann, Markus; Eichbaum, Kathrin; Reininghaus, Mathias; Koglin, Sven; Kammann, Ulrike; Baumann, Lisa; Segner, Helmut; Zennegg, Markus; Buchinger, Sebastian; Reifferscheid, Georg; Hollert, Henner

2015-01-01

Highlights: • Particle-bound DLCs were readily bioavailable during re-suspension of sediments. • DLC uptake and effects in fish were proportional to the concentration in sediments. • Responses of biomarkers reflected the contamination levels of different sediments. • Cyp1a mRNA expression and EROD activity in livers of fish responded immediately. • Histopathological lesions were strong indicators of potential long-term effects. - Abstract: Sediments can act as long-term sinks for environmental pollutants. Within the past decades, dioxin-like compounds (DLCs) such as polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), polychlorinated biphenyls (PCBs), and polycyclic aromatic hydrocarbons (PAHs) have attracted significant attention in the scientific community. To investigate the time- and concentration-dependent uptake of DLCs and PAHs in rainbow trout (Oncorhynchus mykiss) and their associated toxicological effects, we conducted exposure experiments using suspensions of three field-collected sediments from the rivers Rhine and Elbe, which were chosen to represent different contamination levels. Five serial dilutions of contaminated sediments were tested; these originated from the Prossen and Zollelbe sampling sites (both in the river Elbe, Germany) and from Ehrenbreitstein (Rhine, Germany), with lower levels of contamination. Fish were exposed to suspensions of these dilutions under semi-static conditions for 90 days. Analysis of muscle tissue by high resolution gas chromatography and mass spectrometry and of bile liquid by high-performance liquid chromatography showed that particle-bound PCDD/Fs, PCBs and PAHs were readily bioavailable from re-suspended sediments. Uptake of these contaminants and the associated toxicological effects in fish were largely proportional to their sediment concentrations. The changes in the investigated biomarkers closely reflected the different sediment contamination levels: cytochrome P450 1A m

Towards science-based sediment quality standards—Effects of field-collected sediments in rainbow trout (Oncorhynchus mykiss)

Energy Technology Data Exchange (ETDEWEB)

Brinkmann, Markus, E-mail: markus.brinkmann@bio5.rwth-aachen.de [Department of Ecosystem Analysis, Institute for Environmental Research, RWTH Aachen University, Worringerweg 1, 52074 Aachen (Germany); Eichbaum, Kathrin; Reininghaus, Mathias; Koglin, Sven [Department of Ecosystem Analysis, Institute for Environmental Research, RWTH Aachen University, Worringerweg 1, 52074 Aachen (Germany); Kammann, Ulrike [Thünen-Institute of Fisheries Ecology, Palmaille 9, 22767 Hamburg (Germany); Baumann, Lisa; Segner, Helmut [Centre for Fish and Wildlife Health, Vetsuisse Faculty, University of Bern, Länggassstr. 122, 3012 Bern (Switzerland); Zennegg, Markus [Swiss Federal Institute for Materials Science and Technology (Empa), Laboratory for Advanced Analytical Technologies, Überlandstrasse 129, 8600 Dübendorf (Switzerland); Buchinger, Sebastian; Reifferscheid, Georg [Department G3: Biochemistry, Ecotoxicology, Federal Institute of Hydrology (BFG), Am Mainzer Tor 1, 56068 Koblenz (Germany); Hollert, Henner, E-mail: henner.hollert@bio5.rwth-aachen.de [Department of Ecosystem Analysis, Institute for Environmental Research, RWTH Aachen University, Worringerweg 1, 52074 Aachen (Germany); College of Resources and Environmental Science, Chongqing University, 1 Tiansheng Road Beibei, Chongqing 400715 (China); College of Environmental Science and Engineering and State Key Laboratory of Pollution Control and Resource Reuse, Tongji University, 1239 Siping Road, Shanghai (China); State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University (China)

2015-09-15

Highlights: • Particle-bound DLCs were readily bioavailable during re-suspension of sediments. • DLC uptake and effects in fish were proportional to the concentration in sediments. • Responses of biomarkers reflected the contamination levels of different sediments. • Cyp1a mRNA expression and EROD activity in livers of fish responded immediately. • Histopathological lesions were strong indicators of potential long-term effects. - Abstract: Sediments can act as long-term sinks for environmental pollutants. Within the past decades, dioxin-like compounds (DLCs) such as polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), polychlorinated biphenyls (PCBs), and polycyclic aromatic hydrocarbons (PAHs) have attracted significant attention in the scientific community. To investigate the time- and concentration-dependent uptake of DLCs and PAHs in rainbow trout (Oncorhynchus mykiss) and their associated toxicological effects, we conducted exposure experiments using suspensions of three field-collected sediments from the rivers Rhine and Elbe, which were chosen to represent different contamination levels. Five serial dilutions of contaminated sediments were tested; these originated from the Prossen and Zollelbe sampling sites (both in the river Elbe, Germany) and from Ehrenbreitstein (Rhine, Germany), with lower levels of contamination. Fish were exposed to suspensions of these dilutions under semi-static conditions for 90 days. Analysis of muscle tissue by high resolution gas chromatography and mass spectrometry and of bile liquid by high-performance liquid chromatography showed that particle-bound PCDD/Fs, PCBs and PAHs were readily bioavailable from re-suspended sediments. Uptake of these contaminants and the associated toxicological effects in fish were largely proportional to their sediment concentrations. The changes in the investigated biomarkers closely reflected the different sediment contamination levels: cytochrome P450 1A m

Effects of engineered nano-titanium dioxide on pore surface properties and phosphorus adsorption of sediment: its environmental implications.

Science.gov (United States)

Luo, Zhuanxi; Wang, Zhenhong; Wei, Qunshan; Yan, Changzhou; Liu, Feng

2011-09-15

Understanding the environmental safety and human health implications of engineered nanoparticles (ENPs) is of worldwide importance. As an important ENPs, engineered nano-TiO(2) (Enano-TiO(2)) may have been substantially deposited in aquatic sediments because of its widely uses. Sediment pore surface properties would be thus significantly influenced due to the large surface area of Enano-TiO(2). In this study, Enano-TiO(2) was found to greatly impact on sediment pore surface properties. The attachment of Enano-TiO(2) particles to sediment surfaces enhanced markedly BET specific surface area and t-Plot external specific surface area, and thereby increased sediment phosphorus (P) adsorption maximum (S(max)). Contrarily, the fill of Enano-TiO(2) particles into the micropores of sediments could significantly reduce t-Plot micropore specific surface area, and cause slight decrease in sediment P binding energy (K). Clearly, P sorbed in sediment would be easily released because of the decreasing P binding energy of the sediment with elevated Enano-TiO(2). Enano-TiO(2) would thus cause aggravated endogenous pollution in water if such sediment was re-suspended on disturbance. The results obtained in this study contribute to our increasing knowledge of how to regulate physicochemical behavior of pollutants in sediments under the influences of Enano-TiO(2) and/or similar ENPs. Copyright © 2011 Elsevier B.V. All rights reserved.

Sediment and toxic contaminant transport modeling in coastal waters

International Nuclear Information System (INIS)

Onishi, Y.; Mayer, D.W.; Argo, R.S.

1982-02-01

A hydrodynamic model, CAFE-I, a wave refraction model, LO3D, and a sediment and contaminant transport model, FETRA, were selected as tools for evaluating exposure levels of radionuclides, heavy metals, and other toxic chemicals in coastal waters. Prior to the application of these models to the Irish Sea and other coastal waters, the finite element model, FETRA, was tested to demonstrate its ability to simulate sediment and contaminant interactions (e.g., adsorption and desorption), and the mechanisms governing the transport, deposition, and resuspension of contaminated sediments

Multielemental characterization of sediments from rivers and reservoirs of a sediment quality monitoring network of Sao Paulo state, Brazil

Energy Technology Data Exchange (ETDEWEB)

Soares, Walace A.A.; Quinaglia, Gilson A., E-mail: wasoares@sp.gov.br, E-mail: gquinaglia@sp.gov.br [Companhia Ambiental do Estado de Sao Paulo (CETESB), SP (Brazil). Setor de Analises Toxicologicas; Favaro, Deborah I.T., E-mail: defavaro@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (LAN/CRPq/IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Lab. de Analise por Ativacao Neutronica

2013-07-01

The Environment Company of the State of Sao Paulo (CETESB) by means of its quality monitoring network does, systematically, the assessment of water and sediment quality in rivers and reservoirs in the Sao Paulo state. The quality evaluation is done by means 50 parameters in water and 63 for sediment that are considered the more representative for CETESB monitoring. In 2011 the network monitoring analyzed 420 points being 24 in sediments. In the present study the multielemental characterization (total concentration) of 13 sediment samples from 24 rivers and reservoirs belonging to the CETESB monitoring network were analyzed by instrumental neutron activation analysis (INAA). The analytical validation according to precision and accuracy was checked through certified reference materials analyzes BEN (Basalt-IWG-GIT), SL-1 (Lake Sediment - IAEA) and Soil-5 (IAEA), that presents certified concentration values for all elements analyzed. The results obtained for multielemental characterization were compared to NASC values (North American Shale Composite) and the enrichment factor (EF) by using Sc as a normalizer element was calculated. The results showed higher enrichment values for As, Br, Cr, Hf, Ta, Th , U and Zn and rare earth elements (REE) Ce, Eu, La, Nd, Sm, Tb and Yb in many of the tested sediment samples indicating that there may be an anthropogenic contribution for these elements. The multielemental results were also compared to the granulometric composition of the sediment samples. Factorial and Cluster Analysis were applied and indicated that the elements distribution is controlled, mainly by the granulometric fractions of the sediments. (author)

Multielemental characterization of sediments from rivers and reservoirs of a sediment quality monitoring network of Sao Paulo state, Brazil

International Nuclear Information System (INIS)

Soares, Walace A.A.; Quinaglia, Gilson A.; Favaro, Deborah I.T.

2013-01-01

The Environment Company of the State of Sao Paulo (CETESB) by means of its quality monitoring network does, systematically, the assessment of water and sediment quality in rivers and reservoirs in the Sao Paulo state. The quality evaluation is done by means 50 parameters in water and 63 for sediment that are considered the more representative for CETESB monitoring. In 2011 the network monitoring analyzed 420 points being 24 in sediments. In the present study the multielemental characterization (total concentration) of 13 sediment samples from 24 rivers and reservoirs belonging to the CETESB monitoring network were analyzed by instrumental neutron activation analysis (INAA). The analytical validation according to precision and accuracy was checked through certified reference materials analyzes BEN (Basalt-IWG-GIT), SL-1 (Lake Sediment - IAEA) and Soil-5 (IAEA), that presents certified concentration values for all elements analyzed. The results obtained for multielemental characterization were compared to NASC values (North American Shale Composite) and the enrichment factor (EF) by using Sc as a normalizer element was calculated. The results showed higher enrichment values for As, Br, Cr, Hf, Ta, Th , U and Zn and rare earth elements (REE) Ce, Eu, La, Nd, Sm, Tb and Yb in many of the tested sediment samples indicating that there may be an anthropogenic contribution for these elements. The multielemental results were also compared to the granulometric composition of the sediment samples. Factorial and Cluster Analysis were applied and indicated that the elements distribution is controlled, mainly by the granulometric fractions of the sediments. (author)

Interaction of radium with freshwater sediments and their mineral components Pt. 4

International Nuclear Information System (INIS)

Benes, P.; Strejc, P.

1986-01-01

A radiotracer method was used for investigating the adsorption and desorption of radium on stream sediments under conditions similar to those prevailing in waste and surface waters. The effects of pH, ionic strength and Casup(2+) or SOsub(4)sup(2+) ions were studied. The results were compared with analogous data characterizing radium interaction with model solids representing components of the sediments. It was found that the adsorption affinity of the sediments for radium cannot be easily derived from their composition or other properties. No simple correlation with specific surface area, organic matter, oxidic coatings or other components of the sediments was observed. However, an exceptional role of barite (barium sulfate) in the sediments was noted. (author)

Microbial Community Response to Simulated Petroleum Seepage in Caspian Sea Sediments

Directory of Open Access Journals (Sweden)

Katrin Knittel

2017-04-01

Full Text Available Anaerobic microbial hydrocarbon degradation is a major biogeochemical process at marine seeps. Here we studied the response of the microbial community to petroleum seepage simulated for 190 days in a sediment core from the Caspian Sea using a sediment-oil-flow-through (SOFT system. Untreated (without simulated petroleum seepage and SOFT sediment microbial communities shared 43% bacterial genus-level 16S rRNA-based operational taxonomic units (OTU0.945 but shared only 23% archaeal OTU0.945. The community differed significantly between sediment layers. The detection of fourfold higher deltaproteobacterial cell numbers in SOFT than in untreated sediment at depths characterized by highest sulfate reduction rates and strongest decrease of gaseous and mid-chain alkane concentrations indicated a specific response of hydrocarbon-degrading Deltaproteobacteria. Based on an increase in specific CARD-FISH cell numbers, we suggest the following groups of sulfate-reducing bacteria to be likely responsible for the observed decrease in aliphatic and aromatic hydrocarbon concentration in SOFT sediments: clade SCA1 for propane and butane degradation, clade LCA2 for mid- to long-chain alkane degradation, clade Cyhx for cycloalkanes, pentane and hexane degradation, and relatives of Desulfobacula for toluene degradation. Highest numbers of archaea of the genus Methanosarcina were found in the methanogenic zone of the SOFT core where we detected preferential degradation of long-chain hydrocarbons. Sequencing of masD, a marker gene for alkane degradation encoding (1-methylalkylsuccinate synthase, revealed a low diversity in SOFT sediment with two abundant species-level MasD OTU0.96.

Sediment transport through self-adjusting, bedrock-walled waterfall plunge pools

Science.gov (United States)

Scheingross, Joel S.; Lamb, Michael P.

2016-05-01

Many waterfalls have deep plunge pools that are often partially or fully filled with sediment. Sediment fill may control plunge-pool bedrock erosion rates, partially determine habitat availability for aquatic organisms, and affect sediment routing and debris flow initiation. Currently, there exists no mechanistic model to describe sediment transport through waterfall plunge pools. Here we develop an analytical model to predict steady-state plunge-pool depth and sediment-transport capacity by combining existing jet theory with sediment transport mechanics. Our model predicts plunge-pool sediment-transport capacity increases with increasing river discharge, flow velocity, and waterfall drop height and decreases with increasing plunge-pool depth, radius, and grain size. We tested the model using flume experiments under varying waterfall and plunge-pool geometries, flow hydraulics, and sediment size. The model and experiments show that through morphodynamic feedbacks, plunge pools aggrade to reach shallower equilibrium pool depths in response to increases in imposed sediment supply. Our theory for steady-state pool depth matches the experiments with an R2 value of 0.8, with discrepancies likely due to model simplifications of the hydraulics and sediment transport. Analysis of 75 waterfalls suggests that the water depths in natural plunge pools are strongly influenced by upstream sediment supply, and our model provides a mass-conserving framework to predict sediment and water storage in waterfall plunge pools for sediment routing, habitat assessment, and bedrock erosion modeling.

Using 137Cs and 210Pbex and other sediment source fingerprints to document suspended sediment sources in small forested catchments in south-central Chile

International Nuclear Information System (INIS)

Schuller, P.; Walling, D.E.; Iroumé, A.; Quilodrán, C.; Castillo, A.; Navas, A.

2013-01-01

A study of the impact of forest harvesting operations on sediment mobilization from forested catchments has been undertaken in south-central Chile. The study focused on two sets of small paired catchments (treatment and control), with similar soil type, but contrasting mean annual rainfall, located about 400 km apart at Nacimiento (1200 mm yr −1 ) and Los Ulmos (2500 mm yr −1 ). The objective was to study the changes in the relative contribution of the primary sources of fine sediment caused by forestry operations. Attention focused on the pre-harvest and post-harvest periods and the post-replanting period was included for the Nacimiento treatment catchment. The sediment source fingerprinting technique was used to document the contributions of the potential sources. Emphasis was placed on discriminating between the forest slopes, forest roads and channel erosion as potential sources of fine sediment and on assessing the relative contributions of these three sources to the sediment yield from the catchments. The fallout radionuclides (FRNs) 137 Cs and excess lead-210, the environmental radionuclides 226 Ra and 40 K and soil organic matter (SOM) were tested as possible fingerprints for discriminating between potential sediment sources. The Kruskal–Wallis test and discriminant function analysis were used to guide the selection of the optimum fingerprint set for each catchment and observation period. Either one or both of the FRNs were selected for inclusion in the optimum fingerprint for all datasets. The relative contribution of each sediment source to the target sediment load was estimated using the selected fingerprint properties, and a mixing model coupled with a Monte Carlo simulation technique that takes account of uncertainty in characterizing sediment source properties. The goodness of fit of the mixing model was tested by comparing the measured and simulated fingerprint properties for the target sediment samples. In the Nacimiento treatment catchment

Effects-based spatial assessment of contaminated estuarine sediments from Bear Creek, Baltimore Harbor, MD, USA.

Science.gov (United States)

Hartzell, Sharon E; Unger, Michael A; McGee, Beth L; Wilson, Sacoby M; Yonkos, Lance T

2017-10-01

Estuarine sediments in regions with prolonged histories of industrial activity are often laden to significant depths with complex contaminant mixtures, including trace metals and persistent organic pollutants. Given the complexity of assessing risks from multi-contaminant exposures, the direct measurement of impacts to biological receptors is central to characterizing contaminated sediment sites. Though biological consequences are less commonly assessed at depth, laboratory-based toxicity testing of subsurface sediments can be used to delineate the scope of contamination at impacted sites. The extent and depth of sediment toxicity in Bear Creek, near Baltimore, Maryland, USA, was delineated using 10-day acute toxicity tests with the estuarine amphipod Leptocheirus plumulosus, and chemical analysis of trace metals and persistent organic pollutants. A gradient of toxicity was demonstrated in surface sediments with 21 of 22 tested sites differing significantly from controls. Effects were most pronounced (100% lethality) at sites proximate to a historic industrial complex. Sediments from eight of nine core samples to depths of 80 cm were particularly impacted (i.e., caused significant lethality to L. plumulosus) even in locations overlain with relatively non-toxic surface sediments, supporting a conclusion that toxicity observed at the surface (top 2 cm) does not adequately predict toxicity at depth. In seven of nine sites, toxicity of surface sediments differed from toxicity at levels beneath by 28 to 69%, in five instances underestimating toxicity (28 to 69%), and in two instances overestimating toxicity (44 to 56%). Multiple contaminants exceeded sediment quality guidelines and correlated positively with toxic responses within surface sediments (e.g., chromium, nickel, polycyclic aromatic hydrocarbon (PAH), total petroleum hydrocarbon). Use of an antibody-based PAH biosensor revealed that porewater PAH concentrations also increased with depth at most sites. This

Measurements of Two-Phase Suspended Sediment Transport in Breaking Waves Using Volumetric Three-Component Velocimetry

Science.gov (United States)

Ting, F. C. K.; LeClaire, P.

2016-02-01

Understanding the mechanisms of sediment pickup and distribution in breaking waves is important for modeling sediment transport in the surf zone. Previous studies were mostly concerned with bulk sediment transport under specific wave conditions. The distribution of suspended sediments in breaking waves had not been measured together with coherent flow structures. In this study, two-phase flow measurements were obtained under a train of plunging regular waves on a plane slope using the volumetric three-component velocimetry (V3V) technique. The measurements captured the motions of sediment particles simultaneously with the three-component, three-dimensional (3C3D) velocity fields of turbulent coherent structures (large eddies) induced by breaking waves. Sediment particles (solid glass spheres diameter 0.125 to 0.15 mm, specific gravity 2.5) were separated from fluid tracers (mean diameter 13 µm, specific gravity 1.3) based on a combination of particle spot size and brightness in the two-phase images. The interactions between the large eddies and glass spheres were investigated for plunger vortices generated at incipient breaking and for splash-up vortices generated at the second plunge point. The measured data show that large eddies impinging on the bottom was the primary mechanism which lift sediment particles into suspension and momentarily increased near-bed suspended sediment concentration. Although eddy impingement events were sporadic in space and time, the distributions of suspended sediments in the large eddies were not uniform. High suspended sediment concentration and vertical sediment flux were found in the wall-jet region where the impinging flow was deflected outward and upward. Sediment particles were also trapped and carried around by counter-rotating vortices (Figure 1). Suspended sediment concentration was significantly lower in the impingement region where the fluid velocity was downward, even though turbulent kinetic energy in the down flow was

Seasonal variation of sediment toxicity in the Rivers Dommel and Elbe

International Nuclear Information System (INIS)

Hsu, P.; Matthaei, A.; Heise, S.; Ahlf, W.

2007-01-01

Contaminated sediment in the river basin has become a source of pollution with increasing importance to the aquatic ecosystem downstream. To monitor the temporal changes of the sediment bound contaminants in the River Elbe and the River Dommel monthly toxicity tests were applied to layered sediment and river water samples over the course of 10 months. There is an indication that contaminated sediments upstream adversely affected sediments downstream, but this process did not cause a continuous increase of sediment toxicity. A clear decrease of toxic effects in water and upper layer sediment was observed at the River Elbe station in spring related to high water discharge and algal blooms. The less obvious variation of sediment toxicity in the River Dommel could be explained by stable hydrological conditions. Future monitoring programmes should promote a more frequent and intensive sampling regime during these particular events for ecotoxicological evaluation. - Significant impacts of hydrological and biological factors on the ecotoxicological quality in two European rivers (Elbe and Dommel)

Toxicities of sediments below 10 effluent outfalls to near-coastal areas of the Gulf of Mexico

International Nuclear Information System (INIS)

Lewis, M.; Weber, D.; Stanley, R.

1995-01-01

The chemical quality and toxicities of sediments collected in the receiving waters below 10 wastewater outfalls to Northwest Florida coastal areas were evaluated at multiple stations during 1994--1996. Eight types of toxicity tests using 11 test species were used to assess acute and chronic toxicity of the sediments collected below industrial, municipal, power generation and pulp mill outfalls. The primary objectives of the study were to evaluate the relative ability of different assessment procedures to detect toxicity and to provide some much-needed perspective on the impact of major point sources on sediment quality in Gulf of Mexico estuaries. The major chemical contaminants were heavy metals and PAHs. Acute and chronic toxicities were noted. Results of tests with sediment collected at the same location but several months later often differed. The most sensitive species were mysids and an estuarine amphipod. The least sensitive species were fish and macrophyte seedlings. There was poor correlation of effluent toxicity to sediment toxicity in the receiving water. Toxicity of the effluents was greater than that of the sediments. Overall, the unavailability of relevant chronic toxicity methods, uncertain criteria for choice of control stations, lack of guidance on frequency of testing and the dynamic physical and chemical characteristics of sediments are factors that need consideration if sediment monitoring is to be part of the NPDES regulatory process

The mobility of radiocaesium in lake sediment and implications for dating studies

International Nuclear Information System (INIS)

Smith, J.T.; Nolan, L.; Ireland, D.G.; Comans, R.N.J.

1998-01-01

The experiments to study the uptake of radiocaesium by sediment cores from Esthwaite Water, Cumbria, UK in order to develop a model to simultaneously describe uptake of radiocaesium from the water column and diffusion of activity within the sediment has been carried out. By measuring the rate of diffusion of activity through the sediment and sediment pore waters as a function of time the validity of the equilibrium approach to modelling radiocaesium sorption and mobility in sediments has been assessed. By comparison with in situ measurements was found, that rates of diffusion of activity introduced by diffusion across the sediment-water interface (as in the experiments) were approximately one order of magnitude greater than those determined from Chernobyl and weapons test activity-depth profiles. Modelling of the removal of activity from Esthwaite Water showed that the majority of the activity was transported to the sediments by attachment to and settling of suspended particles. It is concluded that activity deposited on particulates (forming the majority of activity observed in situ) was more strongly bound to sediments than that introduced by direct diffusion. This explanation is consistent with observed 'two-phase' 137 Cs profiles in sediments. Predictions of future evolution of the weapons test peak are made on the basis of these studies. It is shown that the peak in the activity-depth profile will remain an important marker for dating studies for the forseeable future

Identifying the cause of sediment toxicity in agricultural sediments: the role of pyrethroids and nine seldom-measured hydrophobic pesticides.

Science.gov (United States)

Weston, Donald P; Ding, Yuping; Zhang, Minghua; Lydy, Michael J

2013-01-01

Few currently used agricultural pesticides are routinely monitored for in the environment. Even if concentrations are known, sediment LC(50) values are often lacking for common sediment toxicity testing species. To help fill this data gap, sediments in California's Central Valley were tested for nine hydrophobic pesticides seldom analyzed: abamectin, diazinon, dicofol, fenpropathrin, indoxacarb, methyl parathion, oxyfluorfen, propargite, and pyraclostrobin. Most were detected, but rarely at concentrations acutely toxic to Hyalella azteca or Chironomus dilutus. Only abamectin, fenpropathrin, and methyl parathion were found at concentrations of potential concern, and only in one or two samples. One-quarter of over 100 samples from agriculture-affected waterways exhibited toxicity, and in three-fourths of the toxic samples, pyrethroids exceeded concentrations expected to cause toxicity. The pyrethroid Bi-fen-thrin in particular, as well as lambda-cyhalothrin, cypermethrin, esfenvalerate, permethrin, and the organophosphate chlorpyrifos, were primarily responsible for the observed toxicity, rather than the more novel analytes, despite the fact that much of the sampling targeted areas of greatest use of the novel pesticides. Copyright © 2012 Elsevier Ltd. All rights reserved.

Ecotoxicological assessment of the pharmaceutical compound Triclosan to freshwater invertebrates with emphasis to spiked sediment tests; Avaliacao ecotoxicologica do farmaco Triclosan para invertebrados de agua doce com enfase em ensaios com sedimento marcado ('spiked sediment')

Energy Technology Data Exchange (ETDEWEB)

Pusceddu, Fabio Hermes

2009-07-01

The increasing of Pharmaceutical and Personal Care Products (PPCPs) occurrence in the aquatic environment cause adverse effects on the human health and aquatic communities. The environmental risk of the PPCPs associated with the possibility of synergic effects between PCPPs and the increase of the use of synthetic organic compounds, unchained a great concern on the toxic potential to biota aquatic. Triclosan (5-chloro-2-(2,4-dichlorophenoxy)-phenol) is a pharmaceutical compound widely used due your antibacterial mechanism effect, found in at least 932 products such as shampoos, toilet soaps, deodorants, lotions, toothpaste, detergents, socks and underwear, among others. Currently, studies about the Triclosan toxicity in the water and, mainly in the sediment, are poorly. We have the knowledge that the photodegradation of this product results into dichlorodibenzo-p-dioxin, and now it has great discussion on environmental agencies, like EPA, about the release or restriction of this product. The aim of this work is to assess the effects of Triclosan on mortality of insect larvae Chironomus xanthus and mortality and reproduction inhibition of microcrustacea Ceriodaphnia dubia exposed to Triclosan spiked sediments based on standard methods EPA and OECD. The EC50;96H obtained on acute toxicity tests with C. xanthus was 45,26 mg.Kg{sup -1}. The chronic toxicity tests with C. dubia using spiked sediments were performed following the procedure in Burton and MacPherson (1995). A no-observed-effect concentrations and lowest-observed-effect concentration were 5,78 e 6,94 mg.Kg{sup -1}, respectively. (author)

Data reduction in cascade impactor and sedimentation battery

International Nuclear Information System (INIS)

Boulaud, Denis; Diouri, Mohamed.

1982-07-01

The determination of the mass distribution of an aerosol from data collected by a cascade impactor or a sedimentation battery implies the size characterization of each impactor stage or each battery length. In the case of the impactor four data reduction methods were compared. Preinning and Picknett's methods, a simulation method and the wellknown effective cut off size method. A theoretical simulation showed that both the simulation and Picknett's methods were the best adapted to restituting a mass distribution with an uncertainty not exceeding 5% for the mass median diameter and 10% for the standard deviation. In the case of the sedimentation battery a new method was developed allowing data reduction when the analytical shape of the size distribution is known. A theoretical simulation was carried out in order to test our method. The test showed that this method was also adapted to restituting the distribution shape, however the size range covered by the sedimentation battery was generally smaller than that of the impactor [fr

Apportioning sources of organic matter in streambed sediments: An integrated molecular and compound-specific stable isotope approach

Energy Technology Data Exchange (ETDEWEB)

Cooper, Richard J., E-mail: Richard.J.Cooper@uea.ac.uk [School of Environmental Sciences, University of East Anglia, Norwich Research Park, Norwich NR4 7TJ (United Kingdom); Pedentchouk, Nikolai; Hiscock, Kevin M.; Disdle, Paul [School of Environmental Sciences, University of East Anglia, Norwich Research Park, Norwich NR4 7TJ (United Kingdom); Krueger, Tobias [IRI THESys, Humboldt University, 10099 Berlin (Germany); Rawlins, Barry G. [British Geological Survey, Keyworth, Nottingham NG12 5GG (United Kingdom)

2015-07-01

We present a novel application for quantitatively apportioning sources of organic matter in streambed sediments via a coupled molecular and compound-specific isotope analysis (CSIA) of long-chain leaf wax n-alkane biomarkers using a Bayesian mixing model. Leaf wax extracts of 13 plant species were collected from across two environments (aquatic and terrestrial) and four plant functional types (trees, herbaceous perennials, and C{sub 3} and C{sub 4} graminoids) from the agricultural River Wensum catchment, UK. Seven isotopic (δ{sup 13}C{sub 27}, δ{sup 13}C{sub 29}, δ{sup 13}C{sub 31}, δ{sup 13}C{sub 27–31}, δ{sup 2}H{sub 27}, δ{sup 2}H{sub 29}, and δ{sup 2}H{sub 27–29}) and two n-alkane ratio (average chain length (ACL), carbon preference index (CPI)) fingerprints were derived, which successfully differentiated 93% of individual plant specimens by plant functional type. The δ{sup 2}H values were the strongest discriminators of plants originating from different functional groups, with trees (δ{sup 2}H{sub 27–29} = − 208‰ to − 164‰) and C{sub 3} graminoids (δ{sup 2}H{sub 27–29} = − 259‰ to − 221‰) providing the largest contrasts. The δ{sup 13}C values provided strong discrimination between C{sub 3} (δ{sup 13}C{sub 27–31} = − 37.5‰ to − 33.8‰) and C{sub 4} (δ{sup 13}C{sub 27–31} = − 23.5‰ to − 23.1‰) plants, but neither δ{sup 13}C nor δ{sup 2}H values could uniquely differentiate aquatic and terrestrial species, emphasizing a stronger plant physiological/biochemical rather than environmental control over isotopic differences. ACL and CPI complemented isotopic discrimination, with significantly longer chain lengths recorded for trees and terrestrial plants compared with herbaceous perennials and aquatic species, respectively. Application of a comprehensive Bayesian mixing model for 18 streambed sediments collected between September 2013 and March 2014 revealed considerable temporal variability in the

Remote Sensing of Suspended Sediment Dynamics in the Mississippi Sound

Science.gov (United States)

Merritt, D. N.; Skarke, A. D.; Silwal, S.; Dash, P.

2016-02-01

The Mississippi Sound is a semi-enclosed estuary between the coast of Mississippi and a chain of offshore barrier islands with relatively shallow water depths and high marine biodiversity that is wildly utilized for commercial fishing and public recreation. The discharge of sediment-laden rivers into the Mississippi Sound and the adjacent Northern Gulf of Mexico creates turbid plumes that can extend hundreds of square kilometers along the coast and persist for multiple days. The concentration of suspended sediment in these coastal waters is an important parameter in the calculation of regional sediment budgets as well as analysis of water-quality factors such as primary productivity, nutrient dynamics, and the transport of pollutants as well as pathogens. The spectral resolution, sampling frequency, and regional scale spatial domain associated with satellite based sensors makes remote sensing an ideal tool to monitor suspended sediment dynamics in the Northern Gulf of Mexico. Accordingly, the presented research evaluates the validity of published models that relate remote sensing reflectance with suspended sediment concentrations (SSC), for similar environmental settings, with 51 in situ observations of SSC from the Mississippi Sound. Additionally, regression analysis is used to correlate additional in situ observations of SSC in Mississippi Sound with coincident observations of visible and near-infrared band reflectance collected by the Moderate Resolution Imaging Spectroradiometer (MODIS) sensor aboard the Aqua satellite, in order to develop a site-specific empirical predictive model for SSC. Finally, specific parameters of the sampled suspended sediment such as grain size and mineralogy are analyzed in order to quantify their respective contributions to total remotely sensed reflectance.

The response of source-bordering aeolian dunefields to sediment-supply changes 1: Effects of wind variability and river-valley morphodynamics

Science.gov (United States)

Sankey, Joel B.; Kasprak, Alan; Caster, Joshua; East, Amy E.; Fairley, Helen C.

2018-06-01

Source-bordering dunefields (SBDs), which are primarily built and maintained with river-derived sediment, are found in many large river valleys and are currently impacted by changes in sediment supply due to climate change, land use changes, and river regulation. Despite their importance, a physically based, applied approach for quantifying the response of SBDs to changes in sediment supply does not exist. To address this knowledge gap, here we develop an approach for quantifying the geomorphic responses to sediment-supply alteration based on the interpretation of dunefield morphodynamics from geomorphic change detection and wind characteristics. We use the approach to test hypotheses about the response of individual dunefields to variability in sediment supply at three SBDs along the Colorado River in Grand Canyon, Arizona, USA during the 11 years between 2002 and 2013 when several river floods rebuilt some river sandbars and channel margin deposits that serve as sediment source areas for the SBDs. We demonstrate that resupply of fluvially sourced aeolian sediment occurred at one of the SBDs, but not at the other two, and attribute this differential response to site-specific variability in geomorphology, wind, and sediment source areas. The approach we present is applied in a companion study to shorter time periods with high-resolution topographic data that bracket individual floods in order to infer the resupply of fluvially sourced aeolian sediment to SBDs by managed river flows. Such an applied methodology could also be useful for measuring sediment connectivity and anthropogenic alterations of connectivity in other coupled fluvial-aeolian environments.

The response of source-bordering aeolian dunefields to sediment-supply changes 1: Effects of wind variability and river-valley morphodynamics

Science.gov (United States)

Sankey, Joel B.; Kasprak, Alan; Caster, Joshua; East, Amy; Fairley, Helen C.

2018-01-01

Source-bordering dunefields (SBDs), which are primarily built and maintained with river-derived sediment, are found in many large river valleys and are currently impacted by changes in sediment supply due to climate change, land use changes, and river regulation. Despite their importance, a physically based, applied approach for quantifying the response of SBDs to changes in sediment supply does not exist. To address this knowledge gap, here we develop an approach for quantifying the geomorphic responses to sediment-supply alteration based on the interpretation of dunefield morphodynamics from geomorphic change detection and wind characteristics. We use the approach to test hypotheses about the response of individual dunefields to variability in sediment supply at three SBDs along the Colorado River in Grand Canyon, Arizona, USA during the 11 years between 2002 and 2013 when several river floods rebuilt some river sandbars and channel margin deposits that serve as sediment source areas for the SBDs. We demonstrate that resupply of fluvially sourced aeolian sediment occurred at one of the SBDs, but not at the other two, and attribute this differential response to site-specific variability in geomorphology, wind, and sediment source areas. The approach we present is applied in a companion study to shorter time periods with high-resolution topographic data that bracket individual floods in order to infer the resupply of fluvially sourced aeolian sediment to SBDs by managed river flows. Such an applied methodology could also be useful for measuring sediment connectivity and anthropogenic alterations of connectivity in other coupled fluvial-aeolian environments.

A CARD-FISH protocol for the identification and enumeration of cyanobacterial akinetes in lake sediments.

Science.gov (United States)

Ramm, Jessica; Lupu, Achsa; Hadas, Ora; Ballot, Andreas; Rücker, Jacqueline; Wiedner, Claudia; Sukenik, Assaf

2012-10-01

Akinetes are the dormant cells of Nostocales (cyanobacteria) that enable the organisms to survive harsh environmental conditions while resting in bottom sediments. The germination of akinetes assists the dispersal and persistence of the species. The assessment of the akinete pool in lake sediments is essential to predict the bloom formation of the Nostocales population. We present here the implementation of an improved catalysed reporter deposition (CARD)-fluorescence in situ hybridization (FISH) protocol to assist the identification and quantification of akinetes in sediment samples. Several 16S rRNA gene oligonucleotide probes were evaluated for labelling akinetes of various species of Anabaena, Aphanizomenon and Cylindrospermopsis. Akinetes of all the taxa studied were successfully labelled and could be easily detected by their bright fluorescence signal. The probes' specificity was tested with 32 strains of different taxa. All six Cylindrospermopsis raciborskii strains were labelled with a specific probe for its 16S rRNA gene. A more general probe labelled 73% of the Anabaena and Aphanizomenon strains. The counting data of field samples obtained with CARD-FISH and the regular light microscopy approach did not differ significantly, confirming the suitability of both methods. The CARD-FISH approach was found to be less time-consuming because of better visibility of akinetes. © 2012 Federation of European Microbiological Societies. Published by Blackwell Publishing Ltd. All rights reserved.

Intercomparison of transuranics in sediments

International Nuclear Information System (INIS)

Nilsson, K.

1981-01-01

This paper summarizes the results of a recent intercomparison of transuranic analyses in Nordic sediments undertaken by five laboratories. Five different samplers were tested to determine their consistency and utility. Plutonium and americium were determined in all the samples and the analysis of variance is discussed. (author)

Human impact on sediment fluxes within the Blue Nile and Atbara River basins

Science.gov (United States)

Balthazar, Vincent; Vanacker, Veerle; Girma, Atkilt; Poesen, Jean; Golla, Semunesh

2013-01-01

A regional assessment of the spatial variability in sediment yields allows filling the gap between detailed, process-based understanding of erosion at field scale and empirical sediment flux models at global scale. In this paper, we focus on the intrabasin variability in sediment yield within the Blue Nile and Atbara basins as biophysical and anthropogenic factors are presumably acting together to accelerate soil erosion. The Blue Nile and Atbara River systems are characterized by an important spatial variability in sediment fluxes, with area-specific sediment yield (SSY) values ranging between 4 and 4935 t/km2/y. Statistical analyses show that 41% of the observed variation in SSY can be explained by remote sensing proxy data of surface vegetation cover, rainfall intensity, mean annual temperature, and human impact. The comparison of a locally adapted regression model with global predictive sediment flux models indicates that global flux models such as the ART and BQART models are less suited to capture the spatial variability in area-specific sediment yields (SSY), but they are very efficient to predict absolute sediment yields (SY). We developed a modified version of the BQART model that estimates the human influence on sediment yield based on a high resolution composite measure of local human impact (human footprint index) instead of countrywide estimates of GNP/capita. Our modified version of the BQART is able to explain 80% of the observed variation in SY for the Blue Nile and Atbara basins and thereby performs only slightly less than locally adapted regression models.

Temperature signal in suspended sediment export from an Alpine catchment

Directory of Open Access Journals (Sweden)

A. Costa

2018-01-01

Full Text Available Suspended sediment export from large Alpine catchments ( >  1000 km2 over decadal timescales is sensitive to a number of factors, including long-term variations in climate, the activation–deactivation of different sediment sources (proglacial areas, hillslopes, etc., transport through the fluvial system, and potential anthropogenic impacts on the sediment flux (e.g. through impoundments and flow regulation. Here, we report on a marked increase in suspended sediment concentrations observed near the outlet of the upper Rhône River Basin in the mid-1980s. This increase coincides with a statistically significant step-like increase in basin-wide mean air temperature. We explore the possible explanations of the suspended sediment rise in terms of changes in water discharge (transport capacity, and the activation of different potential sources of fine sediment (sediment supply in the catchment by hydroclimatic forcing. Time series of precipitation and temperature-driven snowmelt, snow cover, and ice melt simulated with a spatially distributed degree-day model, together with erosive rainfall on snow-free surfaces, are tested to explore possible reasons for the rise in suspended sediment concentration. We show that the abrupt change in air temperature reduced snow cover and the contribution of snowmelt, and enhanced ice melt. The results of statistical tests show that the onset of increased ice melt was likely to play a dominant role in the suspended sediment concentration rise in the mid-1980s. Temperature-driven enhanced melting of glaciers, which cover about 10 % of the catchment surface, can increase suspended sediment yields through an increased contribution of sediment-rich glacial meltwater, increased sediment availability due to glacier recession, and increased runoff from sediment-rich proglacial areas. The reduced extent and duration of snow cover in the catchment are also potential contributors to the rise in suspended sediment