Test of RIPL-2 cross section calculations

International Nuclear Information System (INIS)

Herman, M.

2002-01-01

The new levels and optical segments and microscopic HF-BCS level densities (part of the density segment) were tested in practical calculations of cross sections for neutron induced reactions on 22 targets (40-Ca, 47-Ti, 52-Cr, 55-Mn, 58-Ni, 63-Cu, 71-Ga, 80-Se, 92-Mo, 93-Nb, 100-Mo, 109-Ag, 114-Cd, 124-Sn, 127-I, 133-Cs, 140-Ce, 153-Eu, 169-Tm, 186-W, 197-Au, 208-Pb). For each target all reactions involving up to 3 neutron, 1 proton and 1 α-particle emissions (subject to actual reaction thresholds) were considered in the incident energy range from 1 keV up to 20 MeV (in some cases up to 27 MeV). In addition, total, elastic, and neutron capture cross sections were calculated

Vertical drop test of a transport fuselage center section including the wheel wells

Science.gov (United States)

Williams, M. S.; Hayduk, R. J.

1983-01-01

A Boeing 707 fuselage section was drop tested to measure structural, seat, and anthropomorphic dummy response to vertical crash loads. The specimen had nominally zero pitch, roll and yaw at impact with a sink speed of 20 ft/sec. Results from this drop test and other drop tests of different transport sections will be used to prepare for a full-scale crash test of a B-720.

Finite Element Simulations of Two Vertical Drop Tests of F-28 Fuselage Sections

Science.gov (United States)

Jackson, Karen E.; Littell, Justin D.; Annett, Martin S.; Haskin, Ian M.

2018-01-01

In March 2017, a vertical drop test of a forward fuselage section of a Fokker F-28 MK4000 aircraft was conducted as part of a joint NASA/FAA project to investigate the performance of transport aircraft under realistic crash conditions. In June 2017, a vertical drop test was conducted of a wing-box fuselage section of the same aircraft. Both sections were configured with two rows of aircraft seats, in a triple-double configuration. A total of ten Anthropomorphic Test Devices (ATDs) were secured in seats using standard lap belt restraints. The forward fuselage section was also configured with luggage in the cargo hold. Both sections were outfitted with two hat racks, each with added ballast mass. The drop tests were performed at the Landing and Impact Research facility located at NASA Langley Research Center in Hampton, Virginia. The measured impact velocity for the forward fuselage section was 346.8-in/s onto soil. The wing-box section was dropped with a downward facing pitch angle onto a sloping soil surface in order to create an induced forward acceleration in the airframe. The vertical impact velocity of the wing-box section was 349.2-in/s. A second objective of this project was to assess the capabilities of finite element simulations to predict the test responses. Finite element models of both fuselage sections were developed for execution in LS-DYNA(Registered Trademark), a commercial explicit nonlinear transient dynamic code. The models contained accurate representations of the airframe structure, the hat racks and hat rack masses, the floor and seat tracks, the luggage in the cargo hold for the forward section, and the detailed under-floor structure in the wing-box section. Initially, concentrated masses were used to represent the inertial properties of the seats, restraints, and ATD occupants. However, later simulations were performed that included finite element representations of the seats, restraints, and ATD occupants. These models were developed to more

Modeling and Simulation of a Nuclear Fuel Element Test Section

Science.gov (United States)

Moran, Robert P.; Emrich, William

2011-01-01

"The Nuclear Thermal Rocket Element Environmental Simulator" test section closely simulates the internal operating conditions of a thermal nuclear rocket. The purpose of testing is to determine the ideal fuel rod characteristics for optimum thermal heat transfer to their hydrogen cooling/working fluid while still maintaining fuel rod structural integrity. Working fluid exhaust temperatures of up to 5,000 degrees Fahrenheit can be encountered. The exhaust gas is rendered inert and massively reduced in temperature for analysis using a combination of water cooling channels and cool N2 gas injectors in the H2-N2 mixer portion of the test section. An extensive thermal fluid analysis was performed in support of the engineering design of the H2-N2 mixer in order to determine the maximum "mass flow rate"-"operating temperature" curve of the fuel elements hydrogen exhaust gas based on the test facilities available cooling N2 mass flow rate as the limiting factor.

The fabrication of a vanadium-stainless steel test section for MHD testing of insulator coatings in flowing lithium

International Nuclear Information System (INIS)

Reed, C.B.; Mattas, R.F.; Smith, D.L.; Chung, H.; Tsai, H.-C.; Morgan, G.D.; Wille, G.W.; Young, C.

1996-01-01

To test the magnetohydrodynamic (MHD) pressure drop reduction performance of candidate insulator coatings for the ITER Vanadium/Lithium Breeding Blanket, a test section comprised of a V- 4Cr-4Ti liner inside a stainless steel pipe was designed and fabricated. Theoretically, the MHD pressure drop reduction benefit resulting, from an electrically insulating coating on a vanadium- lined pipe is identical to the benefit derived from an insulated pipe fabricated of vanadium alone. A duplex test section design consisting of a V alloy liner encased in a SS pressure boundary provided protection for vanadium from atmospheric contamination during operation at high temperature and obviated any potential problems with vanadium welding while also minimizing the amount of V alloy material required. From the MHD and insulator coating- point of view, the test section outer SS wall and inner V alloy liner can be modeled simply as a wall having a sandwich construction. Two 52.3 mm OD x 2.9 m long V-alloy tubes were fabricated by Century Tubes from 64 mm x 200 mm x 1245 mm extrusions produced by Teledyne Wah Chang. The test section's duplex structure was subsequently fabricated at Century Tubes by drawing down a SS pipe (2 inch schedule 10) over one of the 53.2 mm diameter V tubes

Determination of a test section parameters for Iris nuclear reactor pressurizer

International Nuclear Information System (INIS)

Silva, Mario A.B. da; Lira, Carlos A.B. de O.

2009-01-01

An integral, modular and medium size nuclear reactor, known as IRIS, is being developed by Westinghouse and by research centers. IRIS is characterized by having most of its components inside the pressure vessel, eliminating the probability of accidents. Due to its integral configuration, there is no spray system for boron homogenization, which may cause power transients. Thus, boron mixing must be investigated. The aim of this paper is to establish the conditions under which a test section has to be built for boron dispersion analysis inside IRIS reactor pressurizer. Through Fractional Scaling Analysis, which is a new methodology of similarity, the main parameters for a test section are obtained. By combining Fractional Scaling Analysis with local scaling for the densimetric Froude number and a previously established volumetric scale factor, the values of recirculation orifices, inlet water temperature, time scale factor and recirculation flow for the test section (model) are determined so that boron distribution is well represented in IRIS reactor pressurizer (prototype). Analytical solutions were used to validate the adopted methodology and when the results simulated in the model are compared to those that characterize the prototype, the agreement for both systems is absolute. The thermal power also influences boron distribution inside the test section. This power is determined by condensation laws in the vapor region and by suitable correlations for free convection. The fractions for rising inlet recirculation water enthalpy and vapor formation are also considered. (author)

Finite Element Analysis and Test Results Comparison for the Hybrid Wing Body Center Section Test Article

Science.gov (United States)

Przekop, Adam; Jegley, Dawn C.; Rouse, Marshall; Lovejoy, Andrew E.

2016-01-01

This report documents the comparison of test measurements and predictive finite element analysis results for a hybrid wing body center section test article. The testing and analysis efforts were part of the Airframe Technology subproject within the NASA Environmentally Responsible Aviation project. Test results include full field displacement measurements obtained from digital image correlation systems and discrete strain measurements obtained using both unidirectional and rosette resistive gauges. Most significant results are presented for the critical five load cases exercised during the test. Final test to failure after inflicting severe damage to the test article is also documented. Overall, good comparison between predicted and actual behavior of the test article is found.

Demonstration tests for HTGR fuel elements and core components with test sections in HENDEL

Energy Technology Data Exchange (ETDEWEB)

Miyamoto, Yoshiaki; Hino, Ryutaro; Inagaki, Yoshiyuki [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment] [and others

1995-03-01

In the fuel stack test section (T{sub 1}) of the Helium Engineering Demonstration Loop (HENDEL), thermal and hydraulic performances of helium gas flows through a fuel rod channel and a fuel stack have been investigated for the High-Temperature Engineering Test Reactor (HTTR) core thermal design. The test data showed that the turbulent characteristics appearing in the Reynolds number above 2000: no typical behavior in the transition zone, and friction factors and heat transfer coefficients in the fuel channel were found to be higher than those in a smooth annular channel. Heat transfer behavior of gas flow in a fuel element channel with blockage and cross-flow through a gap between upper and lower fuel elements stacked was revealed using the mock-up models. On the other hand, demonstration tests have been performed to verify thermal and hydraulic characteristics and structural integrity related to the core bottom structure using a full-scale test facility named as the in-core structure test section (T{sub 2}). The sealing performance test revealed that the leakage of low-temperature helium gas through gaps between the permanent reflector blocks to the core was very low level compared with the HTTR design value and no change of the leakage flow rate were observed after a long term operation. The heat transfer tests including thermal transient at shutdown of gas circulators verified good insulating performance of core insulation structures in the core bottom structure and the hot gas duct; the temperature of the metal portion of these structure was below the design value. Examination of the thermal mixing characteristics indicated that the mixing of the hot helium gas started at a hot plenum and finished completely at downstream of the outlet hot gas duct. The present results obtained from these demonstration tests have been practically applied to the detailed design works and licensing procedures of the HTTR. (J.P.N.) 92 refs.

Nonlinear Analysis and Preliminary Testing Results of a Hybrid Wing Body Center Section Test Article

Science.gov (United States)

Przekop, Adam; Jegley, Dawn C.; Rouse, Marshall; Lovejoy, Andrew E.; Wu, Hsi-Yung T.

2015-01-01

A large test article was recently designed, analyzed, fabricated, and successfully tested up to the representative design ultimate loads to demonstrate that stiffened composite panels with through-the-thickness reinforcement are a viable option for the next generation large transport category aircraft, including non-conventional configurations such as the hybrid wing body. This paper focuses on finite element analysis and test data correlation of the hybrid wing body center section test article under mechanical, pressure and combined load conditions. Good agreement between predictive nonlinear finite element analysis and test data is found. Results indicate that a geometrically nonlinear analysis is needed to accurately capture the behavior of the non-circular pressurized and highly-stressed structure when the design approach permits local buckling.

UHV testing of spare straight section chambers of Indus-2

International Nuclear Information System (INIS)

Tiwari, S.K.; Ratnakala, K.C.; Sridhar, R.; Bhange, N.J.; Netram; Shukla, S.K.

2015-01-01

The vacuum system of Synchrotron Radiation Source, Indus-2, in RRCAT has been functioning up to the mark, continuously for last 10 years. To continue the same trouble-free functioning, it was planned to procure spares for all critical vacuum components, test for UHV performance and keep ready for installation, in case of requirement. As a part of this planning, fifteen chambers made of Aluminium alloy (6063 T6), procured as spare straight section chambers for Indus-2, and were tested for UHV performance. They were tested in batches of 2 or 3 chambers, depending upon their length, and the similar testing-procedure was followed. This paper narrates the tests carried out, and the results obtained. Ultimate vacuum in the range (2 to 9) x 10 -10 mbar was achieved. (author)

Cross sections, benchmarks, etc.: What is data testing all about

International Nuclear Information System (INIS)

Wagschal, J.; Yeivin, Y.

1985-01-01

In order to determine the consistency of two distinct measurements of a physical quantity, the discrepancy d between the two should be compared with its own standard deviation, σ = √(σ/sub 1//sup 2/+σ/sub 2//sup 2/). To properly test a given cross-section library by a set of benchmark (integral) measurements, the quantity corresponding to (d/σ)/sup 2/ is the quadratic d/sup dagger/C/sup -1/d. Here d is the vector of which the components are the discrepancies between the calculated values of the integral parameters and their corresponding measured values, and C is the uncertainty matrix of these discrepancies. This quadratic form is the only true measure of the joint consistency of the library and benchmarks. On the other hand, the very matrix C is essentially all one needs to adjust the library by the benchmarks. Therefore, any argument against adjustment simultaneously disqualifies all serious attempts to test cross-section libraries against integral benchmarks

Drop test and crash simulation of a civil airplane fuselage section

Directory of Open Access Journals (Sweden)

Liu Xiaochuan

2015-04-01

Full Text Available Crashworthiness of a civil airplane fuselage section was studied in this paper. Firstly, the failure criterion of a rivet was studied by test, showing that the ultimate tension and shear failure loads were obviously affected by the loading speed. The relations between the loading speed and the average ultimate shear, tension loads were expressed by two logarithmic functions. Then, a vertical drop test of a civil airplane fuselage section was conducted with an actual impact velocity of 6.85 m/s, meanwhile the deformation of cabin frame and the accelerations at typical locations were measured. The finite element model of a main fuselage structure was developed and validated by modal test, and the error between the calculated frequencies and the test ones of the first four modes were less than 5%. Numerical simulation of the drop test was performed by using the LS-DYNA code and the simulation results show a good agreement with that of drop test. Deforming mode of the analysis was the same as the drop test; the maximum average rigid acceleration in test was 8.81g while the calculated one was 9.17g, with an error of 4.1%; average maximum test deformation at four points on the front cabin floor was 420 mm, while the calculated one was 406 mm, with an error of 3.2%; the peak value of the calculated acceleration at a typical location was 14.72g, which is lower than the test result by 5.46%; the calculated rebound velocity result was greater than the test result 17.8% and energy absorption duration was longer than the test result by 5.73%.

Heavy Section Steel Technology Program. Part II. Intermediate vessel testing

International Nuclear Information System (INIS)

Whitman, G.D.

1975-01-01

The testing of the intermediate pressure vessels is a major activity under the Heavy Section Steel Technology Program. A primary objective of these tests is to develop or verify methods of fracture prediction, through the testing of selected structures and materials, in order that a valid basis can be established for evaluating the serviceability and safety of light-water reactor pressure vessels. These vessel tests were planned with sufficiently specific objectives that substantial quantitative weight could be given to the results. Each set of testing conditions was chosen so as to provide specific data by which analytical methods of predicting flaw growth, and in some cases crack arrest, could be evaluated. Every practical effort was made to assure that results would be relevant to some aspect of real reactor pressure vessel performance through careful control of material properties, selection of test temperatures, and design of prepared flaws. 5 references

Design of in-pile section monitoring system in fuel test loop

Energy Technology Data Exchange (ETDEWEB)

Sim, B. S.; Park, K. N.; Park, S. K.; Chi, D. Y.; Lee, J. M.; Ahn, S. H.; Lee, C. Y.; Kim, Y. J. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

2005-07-01

In this paper a brief summary of the monitoring system of In-Pile Section(IPS) is described. To meet the user requirements on the test fuel and irradiation conditions, various instruments are installed on the test fuel pin itself and the appropriate locations in IPS. The requirements and descriptions for instruments, gas supply system, and the data acquisition system to sample and record parameters are described.

Design Improvement of Double Pressure Vessel in the In-pile Test Section

Energy Technology Data Exchange (ETDEWEB)

Hong, Jintae; Heo, Sung-Ho; Joung, Chang-Young; Kim, Ka-Hye [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-10-15

To carry out an irradiation test of nuclear fuels, a nuclear fuel test rig should be fabricated and installed in the in-pile test section (IPS), which is installed in the reactor hall. While carrying out an irradiation test, sealing out coolant which passes through the test rig is one of the most important issues. In particular, although the double pressure vessel is assembled with the IPS head by two o-rings and six bolts, 15.5 MPa of highly pressurized coolant leaks through the gap between the vessel and IPS head. Because the temperature of the coolant in the test loop is 300 .deg. C , and the pool of HANARO is 40 .deg. C, the double pressure vessel is necessary to insulate them. Therefore, a new design to prevent the leakage of coolant needs to be developed. In this study, EB welding technique is considered to assemble the double pressure vessel and the IPS head, and their mechanical design is modified to enable the welding process. In this study, an improved design for sealing out the coolant at the pressure boundary between the double pressure vessel and the IPS head has been developed. An EB weld is applied to seal out the pressure boundary, and its sealing performance is verified by NDE, a cross section test, and a hydraulic pressure test. From the verification test results, the improved design can be used in fabricating the IPS for a nuclear fuel irradiation test.

Simulation of Model Force-Loading with Changing Its Position in the Wind Tunnel Test Section

Directory of Open Access Journals (Sweden)

V. T. Bui

2015-01-01

Full Text Available When planning and implementing an aerodynamic experiment, model sizes and its position in the test section of the wind tunnel (WT play very important role. The paper focuses on the value variations of the aerodynamic characteristics of a model through changing its position in the WT test section and on the attenuation of the velocity field disturbance in front of the model. Flow around aerodynamic model profile in the open test section of the low-speed WT T-500 is simulated at BMSTU Department SM3. The problem is solved in a two-dimensional case using the ANSYS Fluent package. The mathematical model of flow is based on the Reynolds equations closed by the SST turbulence model. The paper also presents the results of the experiment. Experiments conducted in WT T-500 well correlate with the calculated data and show the optimal position in the middle of the test section when conducting the weighing and drainage experiments. Disturbance of tunnel dynamic pressure (velocity head and flow upwash around the model profile and circular cylinder in the WT test section is analyzed. It was found that flow upstream from the front stagnation point on the body weakly depends on the Reynolds number and obtained results can be used to assess the level of disturbances in the flow around a model by incompressible airflow.

New Tools to Prepare ACE Cross-section Files for MCNP Analytic Test Problems

International Nuclear Information System (INIS)

Brown, Forrest B.

2016-01-01

Monte Carlo calculations using one-group cross sections, multigroup cross sections, or simple continuous energy cross sections are often used to: (1) verify production codes against known analytical solutions, (2) verify new methods and algorithms that do not involve detailed collision physics, (3) compare Monte Carlo calculation methods with deterministic methods, and (4) teach fundamentals to students. In this work we describe 2 new tools for preparing the ACE cross-section files to be used by MCNP ® for these analytic test problems, simple a ce.pl and simple a ce m g.pl.

Integral test on activation cross section of tag gas nuclides using fast neutron spectrum fields

Energy Technology Data Exchange (ETDEWEB)

Aoyama, Takafumi; Suzuki, Soju [Power Reactor and Nuclear Fuel Development Corp., Oarai, Ibaraki (Japan). Oarai Engineering Center

1997-03-01

Activation cross sections of tag gas nuclides, which will be used for the failed fuel detection and location in FBR plants, were evaluated by the irradiation tests in the fast neutron spectrum fields in JOYO and YAYOI. The comparison of their measured radioactivities and the calculated values using the JENDL-3.2 cross section set showed that the C/E values ranged from 0.8 to 2.8 for the calibration tests in YAYOI and that the present accuracies of these cross sections were confirmed. (author)

Equilibrium quality and mass flux distributions in an adiabatic three-subchannel test section

International Nuclear Information System (INIS)

Yadigaroglu, G.; Maganas, A.

1993-01-01

An experiment was designed to measure the fully-developed quality and mass flux distributions in an adiabatic three-subchannel test section. The three subchannels had the geometrical characteristics of the corner, side, and interior subchannels of a BWR-5 rod bundle. Data collected with Refrigerant-144 at pressures ranging from 7 to 14 bar, simulating operation with water in the range 55 to 103 bar are reported. The average mass flux and quality in the test section were in the ranges 1300 to 1750 kg/m s and -0.03 to 0.25, respectively. The data are analyzed and presented in various forms

The cryogenic pumping section of KATRIN and the test experiment TRAP

CERN Document Server

Eichelhardt, F

2011-01-01

The Karlsruhe Tritium Neutrino experiment (KATRIN) employs a Cryogenic Pumping Section (CPS) at ~ 4.5 K to suppress the tritium penetration into the spectrometers. A test experiment (TRAP - Tritium Argon frost Pump) has been set up to investigate the tritium pumping performance of the CPS.

Sectional pipeline bundles. Design, fabrication and testing of a subsea pipeline connection system

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-08-01

The tests of the prototype system indicated that the system is applicable for connecting pipeline bundle sections. The overall performance of the system is therefore concluded to be satisfactory. Some modifications are required though, for improving the reliability of the system to the level required for offshore North Sea application. The tests showed that connection of the pipeline bundle sections can be performed for alignment tolerances larger than those expected during a typical subsea installation. Pull-in of bundle end sections can be performed with pull-in wires deployed from surface. The offshore tests showed that handling of wires must be done with great care to avoid possibility for wire entanglement, especially if a fully diverless system is to be used. The flowline connection tool was found to be suitable for final alignment of the individual spool ends. It was demonstrated that face to face contact between the hub faces in the connector was obtained after tie-in. Pressure tests showed that the connector could be sealed by the tie-in force applied by the connection tool tie-in system. However, the standard connector clamp which was used, was found to be insuficient for maintaining the connector effectively sealed after removal of the pull-in force applied by the connection tool. Based on the results proposals for improvements of the system are included. Improvements are applicable to the current system for connection of bundle sections or for tie-in operations, relating to conventional pipelines. The improvements also includes a strong connection clamp suitable for subsea use. The connection clamp will replace the standard clamp devise used in this project. (au) EFP-96. 41 refs.

Equilibrium quality and mass flux distributions in an adiabatic three-subchannel test section

International Nuclear Information System (INIS)

Yadigaroglu, G.; Maganas, A.

1995-01-01

An experiment was designed to measure the fully developed quality and mass flux distributions in an adiabatic three-subchannel test section. The three subchannels had the geometrical characteristics of the corner, side, and interior subchannels of a boiling water reactor (BWR-5) rod bundle. Data collected with Refrigerant-114 at pressures ranging from 7 to 14 bars, simulating operation with water in the range 55 to 103 bars are reported. The average mass flux and quality in the test section were in the ranges 1,300 to 1,750 kg/m 2 · s and -0.03 to 0.25, respectively. The data are analyzed and presented in various forms

Experimental Investigation of Tensile Test on Connection of Cold-formed Cut-curved Steel Section

Science.gov (United States)

Sani, Mohd Syahrul Hisyam Mohd; Muftah, Fadhluhartini; Rahman, Nurul Farraheeda Abdul; Fakri Muda, Mohd

2017-08-01

Cold-formed steel (CFS) is widely used as structural and non-structural components such as roof trusses and purlin. A CFS channel section with double intermediate web stiffener and lipped is chosen based on the broader usage in roof truss construction. CFS section is cut to form cold-formed pre-cut-curved steel section and lastly strengthened by several types of method or likely known as connection to establish the cold-formed cut-curved steel (CFCCS) section. CFCCS is proposed to be used as a top chord section in the roof truss system. The CFCCS is to resist the buckling phenomena of the roof truss structure and reduced the compression effect on the top chord. The tensile test connection of CFCCS section, especially at the flange element with eight types of connection by welding, plate with self-drilling screw and combination is investigated. The flange element is the weakest part that must be solved first other than the web element because they are being cut totally, 100% of their length for curving process. The testing is done using a universal testing machine for a tensile load. From the experiment, specimen with full welding has shown as a good result with an ultimate load of 13.37 kN and reported having 35.41% when compared with normal specimen without any of connection methods. Furthermore, the experimental result is distinguished by using Eurocode 3. The failure of a full welding specimen is due to breaking at the welding location. Additionally, all specimens with either full weld or spot weld or combination failed due to breaking on weld connection, but specimen with flange plate and self-drilling screw failed due to tilting and bearing. Finally, the full welding specimen is chosen as a good connection to perform the strengthening method of CFCCS section.

Optimised design and thermal-hydraulic analysis of the IFMIF/HFTM test section

Energy Technology Data Exchange (ETDEWEB)

Gordeev, S.; Heinzel, V.; Lang, K.H.; Moeslang, A.; Schleisiek, K.; Slobodtchouk, V.; Stratmanns, E.

2003-10-01

On the basis of previous concepts, analyses and experiments, the high flux test module (HFTM) for the International Fusion Materials Irradiation Facility (IFMIF) was further optimised. The work focused on the design and the thermal hydraulic analysis of the HFTM section containing the material specimens to be irradiated, the ''test section'', with the main objective to improve the concept with respect to the optimum use of the available irradiation volume and to the temperature of the specimens. Particular emphasis was laid on the application of design principles which assure stable and reproducible thermal conditions. The present work has confirmed the feasibility and suitability of the optimised design of the HFTM test section with chocolate plate like shaped rigs. In particular it has been shown that the envisaged irradiation temperatures can be reached with acceptable temperature differences inside the specimen stack. The latter can be achieved only by additional electrical heating of the axial ends of the capsules. Division of the heater in three sections with separate power supply and control units is necessary. Maintaining of the temperatures during beam-off periods likewise requires electrical heating. The required electrical heaters - mineral isolated wires - are commercially available. The potential of the CFD code STAR-CD for the thermal hydraulic analysis of complex systems like the HFTM was confirmed. Nevertheless, experimental confirmation is desirable. Suitable experiments are under preparation. To verify the assumptions made on the thermal conductivity of the contact faces and layers between the two shells of the rig, dedicated experiments are suggested. The present work must be complemented by a thermal mechanical analysis of the module. Most critical component in this respect seems to be the rig wall. Furthermore, it will be necessary to investigate the response of the HFTM to power transients, and to determine the requirements

Optimised design and thermal-hydraulic analysis of the IFMIF/HFTM test section

International Nuclear Information System (INIS)

Gordeev, S.; Heinzel, V.; Lang, K.H.; Moeslang, A.; Schleisiek, K.; Slobodtchouk, V.; Stratmanns, E.

2003-10-01

On the basis of previous concepts, analyses and experiments, the high flux test module (HFTM) for the International Fusion Materials Irradiation Facility (IFMIF) was further optimised. The work focused on the design and the thermal hydraulic analysis of the HFTM section containing the material specimens to be irradiated, the ''test section'', with the main objective to improve the concept with respect to the optimum use of the available irradiation volume and to the temperature of the specimens. Particular emphasis was laid on the application of design principles which assure stable and reproducible thermal conditions. The present work has confirmed the feasibility and suitability of the optimised design of the HFTM test section with chocolate plate like shaped rigs. In particular it has been shown that the envisaged irradiation temperatures can be reached with acceptable temperature differences inside the specimen stack. The latter can be achieved only by additional electrical heating of the axial ends of the capsules. Division of the heater in three sections with separate power supply and control units is necessary. Maintaining of the temperatures during beam-off periods likewise requires electrical heating. The required electrical heaters - mineral isolated wires - are commercially available. The potential of the CFD code STAR-CD for the thermal hydraulic analysis of complex systems like the HFTM was confirmed. Nevertheless, experimental confirmation is desirable. Suitable experiments are under preparation. To verify the assumptions made on the thermal conductivity of the contact faces and layers between the two shells of the rig, dedicated experiments are suggested. The present work must be complemented by a thermal mechanical analysis of the module. Most critical component in this respect seems to be the rig wall. Furthermore, it will be necessary to investigate the response of the HFTM to power transients, and to determine the requirements on the electrical

Analytical Work in Support of the Design and Operation of Two Dimensional Self Streamlining Test Sections

Science.gov (United States)

Judd, M.; Wolf, S. W. D.; Goodyer, M. J.

1976-01-01

A method has been developed for accurately computing the imaginary flow fields outside a flexible walled test section, applicable to lifting and non-lifting models. The tolerances in the setting of the flexible walls introduce only small levels of aerodynamic interference at the model. While it is not possible to apply corrections for the interference effects, they may be reduced by improving the setting accuracy of the portions of wall immediately above and below the model. Interference effects of the truncation of the length of the streamlined portion of a test section are brought to an acceptably small level by the use of a suitably long test section with the model placed centrally.

Analysis of a Hybrid Wing Body Center Section Test Article

Science.gov (United States)

Wu, Hsi-Yung T.; Shaw, Peter; Przekop, Adam

2013-01-01

The hybrid wing body center section test article is an all-composite structure made of crown, floor, keel, bulkhead, and rib panels utilizing the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) design concept. The primary goal of this test article is to prove that PRSEUS components are capable of carrying combined loads that are representative of a hybrid wing body pressure cabin design regime. This paper summarizes the analytical approach, analysis results, and failure predictions of the test article. A global finite element model of composite panels, metallic fittings, mechanical fasteners, and the Combined Loads Test System (COLTS) test fixture was used to conduct linear structural strength and stability analyses to validate the specimen under the most critical combination of bending and pressure loading conditions found in the hybrid wing body pressure cabin. Local detail analyses were also performed at locations with high stress concentrations, at Tee-cap noodle interfaces with surrounding laminates, and at fastener locations with high bearing/bypass loads. Failure predictions for different composite and metallic failure modes were made, and nonlinear analyses were also performed to study the structural response of the test article under combined bending and pressure loading. This large-scale specimen test will be conducted at the COLTS facility at the NASA Langley Research Center.

Lexical patterns in the reading comprehension section of the toefl test

Directory of Open Access Journals (Sweden)

Fabiana Macmillan

2006-11-01

Full Text Available The TOEFL (Test of English as a Foreign Language is currently one of the most widely accepted English language proficiency tests. Designed by the ETS (Educational Testing Service, the main purpose of the TOEFL is to determine whether the English language skills of a student applying to a North American college or university are adequate for enrollment into the selected program of study. This study will focus upon the third section of the TOEFL, Reading Comprehension, which consists of several passages followed by questions with different testing purposes. An adaptation of Hoey's (1991 analytical system for the analysis of lexical cohesion in authentic texts will be used to identify bonds connecting reading comprehension questions on the test to key excerpts in the passages they are related to. A number of sample reading comprehension questions taken from practice tests produced by the ETS will be analyzed. The analysis will focus on the relationship between the testing purpose of each question and the type(s of lexical link involved in the identification of the correct answer.

Problems With Section Two ITP TOEFL Test

Directory of Open Access Journals (Sweden)

Rizki Ananda

2016-03-01

Full Text Available This study was designed to investigate (1 the difficulties faced by EFL university students with section two of the ITP, and (2 whether part A or part B was more difficult for them and why. A number of 26 students from two different universities, Syiah Kuala University and the State Islamic University Ar-Raniry were the samples for the test. The data was obtained from a multiple choice questionnaire test consisting of 46 questions, each with 4 answers to choose from. The results showed that inversions (12%, subject-verb agreements (10%, adverb clause connectors (7%, passives (6%, reduced adjective clauses (5%, parallel structures (5% and use of verbs (5% were the most difficult questions for the students. Furthermore, they felt that part B was more difficult than part A, as finding an error in a sentence was harder than completing a sentence from a multiple choice. Furthermore, the length of questions in part A did not affect the amount of time the students spent to complete part A and did not cause them to panic. Also, unfamiliar words in part A were not regarded as a problem by the students. Hence, TOEFL teachers and trainers are highly encouraged to pay more attention to doing study exercises for the seven topics with the highest percentages above in part A and also to more practice for part B.

Experimental evaluation of wall Mach number distributions of the octagonal test section proposed for NASA Lewis Research Center's altitude wind tunnel

Science.gov (United States)

Harrington, Douglas E.; Burley, Richard R.; Corban, Robert R.

1986-01-01

Wall Mach number distributions were determined over a range of test-section free-stream Mach numbers from 0.2 to 0.92. The test section was slotted and had a nominal porosity of 11 percent. Reentry flaps located at the test-section exit were varied from 0 (fully closed) to 9 (fully open) degrees. Flow was bled through the test-section slots by means of a plenum evacuation system (PES) and varied from 0 to 3 percent of tunnel flow. Variations in reentry flap angle or PES flow rate had little or no effect on the Mach number distributions in the first 70 percent of the test section. However, in the aft region of the test section, flap angle and PES flow rate had a major impact on the Mach number distributions. Optimum PES flow rates were nominally 2 to 2.5 percent wtih the flaps fully closed and less than 1 percent when the flaps were fully open. The standard deviation of the test-section wall Mach numbers at the optimum PES flow rates was 0.003 or less.

Four-Point Bending Strength Testing of Pultruded Fiberglass Composite Wind Turbine Blade Sections

International Nuclear Information System (INIS)

Musial, W.; Bourne, B; Hughes, S; Zuteck, M. D.

2001-01-01

The ultimate strength of the PS Enterprises pultruded blade section was experimentally determined under four-point bending at the National Renewable Energy Laboratory. Thirteen 8-foot long full-scale blade segments were individually tested to determine their maximum moment carrying capability. Three airfoil-bending configurations were tested: high- and low-pressure skin buckling, and low pressure skin buckling with foam interior reinforcement. Maximum strain was recorded for each sample on the compressive and tensile surfaces of each test blade. Test data are compared to the results of three analytical buckling prediction methods. Based on deviations from the linear strain versus load curve, data indicate a post-buckling region. High-pressure side buckling occurred sooner than low-pressure side buckling. The buckling analyses were conservative for both configurations, but high-pressure side buckling in particular was substantially under-predicted. Both high- and low-pressure buckling configurations had very similar failure loads. These results suggests that a redundant load path may be providing strength to the section in the post-buckling region, making the onset of panel buckling a poor predictor of ultimate strength for the PS Enterprises pultrusion

Study of the thermal and hydraulic phenomena occurring during power excursion on a heated test section

International Nuclear Information System (INIS)

Nyer, M.

1969-01-01

The thermal and hydrodynamic phenomena occurring during a power excursion were studied in an out-of-pile loop with a water cooled channel at low pressure (1 to 4 atm. abs. ). Circular and rectangular test sections with electrically heated walls of two different thermal diffusivity materials(aluminium and stainless steel) were used. The rectangular test sections were 600 mm long, 35 mm wide and had a 2, 9 mm gap; they simulate two half plates of the M.T.R. fuel element. Natural or forced convection are possible in the test section; the water height above it can be varied from 2.8 to 8 meters and the maximum allowed pressure at its outlet is 4 atm. abs.The heating source is a series of lead batteries which is able to generate, for short periods of time, 85 volts and 25000 amperes; linear, square or exponential power rise versus time can be realized. A 14 channels tape recorder (0-10 000 Hz bandwidth; is used for the measurements of temperature (8/100 mm diameter thermocouple), pressure ('Statham' pressure transducers) and void fraction (X rays). More than 500 tests have been carried out. The influence of the initial water temperature, flow rate, pressure, water height on the water ejections, pressure variations and void fraction in the test section were studied. Tests with energies up to 3000 W/cm in 50 milliseconds were attempted. The energy above which the instabilities appear was determined. An interpretation of the observed phenomena and a simplified theoretical model are presented [fr

Heavy-Section Steel Technology Program intermediate-scale pressure vessel tests

International Nuclear Information System (INIS)

Bryan, R.H.; Merkle, J.G.; Smith, G.C.; Whitman, G.D.

1977-01-01

The tests of intermediate-size vessels with sharp flaws permitted the comparison of experimentally observed behavior with analytical predictions of the behavior of flawed pressure vessels. Fracture strains estimated by linear elastic fracture mechanics (LEFM) were accurate in the cases in which the flaws resided in regions of high transverse restraint and the fracture toughness was sufficiently low for unstable fracture to occur prior to yielding through the vessel wall. When both of these conditions were not present, unstable fracture did occur, always preceded by stable crack growth; and the cylinders with flaws initially less than halfway through the wall attained gross yield prior to burst. Predictions of failure pressure of the vessels with flawed nozzles, based upon LEFM estimates of failure strain, were very conservative. LEFM calculations of critical load were based upon small-specimen fracture toughness test data. Whenever gross yielding preceded failure, the actual strains achieved were considerably greater than the estimated strains at failure based on LEFM. In such cases the strength of the vessel may be no longer dependent upon plane-strain fracture toughness but upon the capacity of the cracked section to carry the imposed load stably in the plastic range. Stable crack growth, which has not been predictable quantitatively, is an important factor in elastic-plastic analysis of strength. The ability of the flawed vessels to attain gross yield in unflawed sections has important qualitative implications on pressure vessel safety margins. The gross yield condition occurs in light-water-reactor pressure vessels at about 2 x design pressure. The intermediate vessel tests that demonstrated a capacity for exceeding this load confirm that the presumed margin of safety is not diminished by the presence of flaws of substantial size, provided that material properties are adequate

Construction of experimental HMA test sections in order to monitor the compaction process

NARCIS (Netherlands)

ter Huerne, Henderikus L.; Molenaar, A.A.A.; van de Ven, M.F.C.

2003-01-01

For getting better understanding about the process of HMA compaction, a test section was constructed while the governing process parameters, like; compaction progress, temperature of the material at which activities were employed, equipment properties and meteorological circumstances, were

Testing for Unit Roots in Small Panels with Short-run and Long-run Cross-sectional Dependencies

OpenAIRE

Yoosoon Chang; Wonho Song

2009-01-01

An IV approach, using as instruments non-linear transformations of the lagged levels, is explored to test for unit roots in panels with general dependency and heterogeneity across cross-sectional units. We allow not only for the cross-sectional dependencies of innovations, but also for the presence of co-integration across cross-sectional levels. Unbalanced panels and panels with differing individual short-run dynamics and cross-sectionally related dynamics are also permitted. We also more ca...

Benchmark experiments to test plutonium and stainless steel cross sections. Topical report

International Nuclear Information System (INIS)

Jenquin, U.P.; Bierman, S.R.

1978-06-01

The Nuclear Regulatory Commission (NRC) commissioned Battelle, Pacific Northwest Laboratory (PNL) to ascertain the accuracy of the neutron cross sections for the isotopes of plutonium and the constituents of stainless steel and determine if improvements can be made in application to criticality safety analysis. NRC's particular area of interest is in the transportation of light-water reactor spent fuel assemblies. The project was divided into two tasks. The first task was to define a set of integral experimental measurements (benchmarks). The second task is to use these benchmarks in neutronics calculations such that the accuracy of ENDF/B-IV plutonium and stainless steel cross sections can be assessed. The results of the first task are given in this report. A set of integral experiments most pertinent to testing the cross sections has been identified and the code input data for calculating each experiment has been developed

Reliability of the Balance Evaluation Systems Test (BESTest) and BESTest sections for adults with hemiparesis

Science.gov (United States)

Rodrigues, Letícia C.; Marques, Aline P.; Barros, Paula B.; Michaelsen, Stella M.

2014-01-01

BACKGROUND: The Balance Evaluation Systems Test (BESTest) was recently created to allow the development of treatments according to the specific balance system affected in each patient. The Brazilian version of the BESTest has not been specifically tested after stroke. OBJECTIVE: To evaluate the intra- and inter-rater reliability and concurrent and convergent validity of the total score of the BESTest and BESTest sections for adults with hemiparesis after stroke. METHOD: The study included 16 subjects (61.1±7.5 years) with chronic hemiparesis (54.5±43.5 months after stroke). The BESTest was administered by two raters in the same week and one of the raters repeated the test after a one-week interval. Intraclass correlation coefficient (ICC) was calculated to assess intra- and interrater reliability. Concurrent validity with the Berg Balance Scale (BBS) and convergent validity with the Activities-specific Balance Confidence scale (ABC-Brazil) were assessed using Pearson's correlation coefficient. RESULTS: Both the BESTest total score (ICC=0.98) and the BESTest sections (ICC between 0.85 and 0.96) have excellent intrarater reliability. Interrater reliability for the total score was excellent (ICC=0.93) and, for the sections, it ranged between 0.71 and 0.94. The correlation coefficient between the BESTest and the BBS and ABC-Brazil were 0.78 and 0.59, respectively. CONCLUSIONS: The Brazilian version of the BESTest demonstrated adequate reliability when measured by sections and could identify what balance system was affected in patients after stroke. Concurrent validity was excellent with the BBS total score and good to excellent with the sections. The total scores but not the sections present adequate convergent validity with the ABC-Brazil. However, other psychometric properties should be further investigated. PMID:25003281

Commissioning of the Ground Test Accelerator Intertank Matching Section

International Nuclear Information System (INIS)

Johnson, K.F.; Sander, O.R.; Atkins, W.H.; Bolme, G.O.; Cole, R.; Connolly, R.; Gilpatrick, J.D.; Ingalls, W.B.; Kersteins, D.; Little, C.; Lohsen, R.A.; Lysenko, W.P.; Mottershead, C.T.; Power, J.; Rusthoi, D.P.; Sandoval, D.P.; Stevens, R.R.; Vaughn, G.; Wadlinger, E.A.; Weiss, R.; Yuan, V.

1992-01-01

The Ground Test Accelerator (GTA) has the objective of verifying much of the technology (physics and engineering) required for producing high-brightness, high-current H - beams. GTA commissioning is staged to verify the beam dynamics design of each major accelerator component as it is brought on-line. The commissioning stages are the 35 keV H - injector, the 2.5 MeV Radio Frequency Quadrupole (RFQ), the Intertank Matching Section (IMS), the 3.2 MeV first 2βγ Drift Tube Linac (DTL-1) module, the 8.7 MeV 2βγ DTL (modules 1--5), and the 24 MeV GTA; all 10 DTL modules. Commissioning results from the IMS beam experiments will be presented

Influence of Test Section Geometry on the Blast Environment in an Explosively Driven Conical Shock Tube

Science.gov (United States)

2018-03-30

ARL-TR-8335•MAR 2018 US Army Research Laboratory Influence of Test Section Geometry on theBlast Environment in an Explosively DrivenConical Shock...ARL-TR-8335•MAR 2018 US Army Research Laboratory Influence of Test Section Geometry on theBlast Environment in an Explosively DrivenConical Shock...TITLE AND SUBTITLE    5a. CONTRACT NUMBER  5b. GRANT NUMBER  5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S)    5d.  PROJECT  NUMBER  5e. TASK NUMBER  5f

To test or not to test: A cross-sectional survey of the psychosocial determinants of self-testing for cholesterol, glucose, and HIV

Directory of Open Access Journals (Sweden)

Dinant Geert-Jan

2011-02-01

Full Text Available Abstract Background Although self-tests are increasingly available and widely used, it is not clear whether their use is beneficial to the users, and little is known concerning the determinants of self-test use. The aim of this study was to identify the determinants of self-test use for cholesterol, glucose, and HIV, and to examine whether these are similar across these tests. Self-testing was defined as using in-vitro tests on body materials, initiated by consumers with the aim of diagnosing a particular disorder, condition, or risk factor for disease. Methods A cross-sectional Internet survey was conducted among 513 self-testers and 600 non-testers, assessing possible determinants of self-test use. The structured questionnaire was based on the Health Belief Model, Theory of Planned Behavior, and Protection Motivation Theory. Data were analyzed by means of logistic regression. Results The results revealed that perceived benefits and self-efficacy were significantly associated with self-testing for all three conditions. Other psychosocial determinants, e.g. gender, cues to action, perceived barriers, subjective norm, and moral obligation, seemed to be more test-specific. Conclusions Psychosocial determinants of self-testing are not identical for all tests and therefore information about self-testing needs to be tailored to a specific test. The general public should not only be informed about advantages of self-test use but also about the disadvantages. Designers of information about self-testing should address all aspects related to self-testing to stimulate informed decision making which, in turn, will result in more effective self-test use.

Verification Test for Ultra-Light Deployment Mechanism for Sectioned Deployable Antenna Reflectors

Science.gov (United States)

Zajac, Kai; Schmidt, Tilo; Schiller, Marko; Seifart, Klaus; Schmalbach, Matthias; Scolamiero, Lucio

2013-09-01

The ultra-light deployment mechanism (UDM) is based on three carbon fibre reinforced plastics (CFRP) curved tape springs made of carbon fibre / cyanate ester prepregs.In the frame of the activity its space application suitability for the deployment of solid reflector antenna sections was investigated. A projected diameter of the full reflector of 4 m to 7 m and specific mass in the order of magnitude of 2.6kg/m2 was focused for requirement derivation.Extensive verification tests including health checks, environmental and functional tests were carried out with an engineering model to enable representative characterizing of the UDM unit.This paper presents the design and a technical description of the UDM as well as a summary of achieved development status with respect to test results and possible design improvements.

Structural damping results from vibration tests of straight piping sections

International Nuclear Information System (INIS)

Ware, A.G.; Thinnes, G.L.

1984-01-01

EG and G Idaho is assisting the USNRC and the Pressure Vessel Research Committee in supporting a final position on revised damping values for structural analyses of nuclear piping systems. As part of this program, a series of vibrational tests on 76-mm and 203-mm (3-in. amd 8-in.) Schedule 40 carbon steel piping was conducted to determine the changes in structural damping due to various parametric effects. The 10-m (33-ft) straight sections of piping were rigidly supported at the ends. Spring, rod, and constant force hangers, as well as a sway brace and snubbers were included as intermediate supports. Excitation was provided by low-force level hammer inpacts, a hydraulic shaker, and a 445-kN (50-ton) overhead crane. Data was recorded using acceleration, strain, and displacement time histories. This paper presents results from the testing showing the effect of stress level and type of supports on structural damping in piping

Longitudinal Acceleration Tests of Overhead Luggage Bins and Auxiliary Fuel Tank in a Transport Airplane Airframe Section

National Research Council Canada - National Science Library

McGuire, Robert

1999-01-01

This report contains the description and test results of overhead stowage bin calibrations and longitudinal impact testing of a 10-foot transport airframe section conducted at the Transportation Research Center Inc. (TRC...

Mixed Waste Management Facility (MWMF) closure, Savannah River Plant: Clay cap test section construction report

Energy Technology Data Exchange (ETDEWEB)

1988-02-26

This report contains appendices 3 through 6 for the Clay Cap Test Section Construction Report for the Mixed Waste Management Facility (MWMF) closure at the Savannah River Plant. The Clay Cap Test Program was conducted to evaluate the source, lab. permeability, in-situ permeability, and compaction characteristics, representative of kaolin clays from the Aiken, South Carolina vicinity. (KJD)

Skin Sensitive Difference of Human Body Sections under Clothing-Smirnov Test of Skin Surface Temperatures' Dynamic Changing

Institute of Scientific and Technical Information of China (English)

LI Jun; WU Hai-yan; WANG Yun-yi

2004-01-01

Skin sensitive difference of human body sections under clothing is the theoretic foundation of thermal insulation clothing design.By a new method of researching on clothing comfort perception,the skin temperature live changing procedure of human body sections affected by the same cold stimulation is inspected.Furthermore with the Smirnov test the skin temperatures dynamic changing patterns of main human body sections are obtained.

Round robin test programmes in the reliability of thick section ultrasonic inspections: state of the art report

International Nuclear Information System (INIS)

Watkins, B.

1987-03-01

Inspection reliability is firstly defined and it is shown how difficult it is to be assessed as the influence of such factors as human performance, equipment malfunction and intrinsic technique capability are difficult to quantify. The manufacture of round robin test specimens is then considered: types of flaw, fabrication of test samples. The results of various round robin test programmes that have been carried out to determine both the capability and reliability of NDE to detect and size flaws in steel section for thick sections directly relevant to the requirements of the nuclear industry, are then reviewed and discussed: US Pressure Vessel research committee programme, PISC I Programme, the defect detection trials, and PISC II Programme

Critical Heat Flux Experiments on the Reactor Vessel Wall Using 2-D Slice Test Section

International Nuclear Information System (INIS)

Jeong, Yong Hoon; Chang, Soon Heung; Baek, Won-Pil

2005-01-01

The critical heat flux (CHF) on the reactor vessel outer wall was measured using the two-dimensional slice test section. The radius and the channel area of the test section were 2.5 m and 10 cm x 15 cm, respectively. The flow channel area and the heater width were smaller than those of the ULPU experiments, but the radius was greater than that of the ULPU. The CHF data under the inlet subcooling of 2 to 25 deg. C and the mass flux 0 to 300 kg/m 2 .s had been acquired. The measured CHF value was generally slightly lower than that of the ULPU. The difference possibly comes from the difference of the test section material and the thickness. However, the general trend of CHF according to the mass flux was similar with that of the ULPU. The experimental CHF data were compared with the predicted values by SULTAN correlation. The SULTAN correlation predicted well this study's data only for the mass flux higher than 200 kg/m 2 .s, and for the exit quality lower than 0.05. The local condition-based correlation was developed, and it showed good prediction capability for broad quality (-0.01 to 0.5) and mass flux ( 2 .s) conditions with a root-mean-square error of 2.4%. There were increases in the CHF with trisodium phosphate-added water

Evaluation of mechanical design fire brick at test section on the HeaTiNG-02

International Nuclear Information System (INIS)

Dedy Haryanto; Riswan Djambiar; Sagino; Edy Sumarno

2013-01-01

The activity was carried out due to the modification of the heating in the HeaTiNG-02 test section. Modification of the heater needs to be done to overcome the obstacles that arise as part of the test section is used. Constraint that often arises is the fall of the heating source with super khantal material when it reaches a certain temperature. To mitigate the super khantal position is initially converted into a vertical position horizontal. The change from vertical to horizontal position on super khantal cause any deformities in refractory fire brick which serves as a support super khantal. Manufacture of refractory design fire brick formation and mechanical strength evaluation performed using CATIA V5 R20 software. Evaluation of fireproof rock mechanics to be based on the mechanical properties of alumina as a refractory material of fire brick. The results of the analysis have a fire brick design stress greater than the bend strength alumina materials, so that the necessary checks before and after the experiment as well as the replacement of refractory fire brick if something is broken. Translational greatest displacement 0.453 mm at a temperature of 1575 K did not give any meaningful form. Thus the refractory fire brick design can be used as heating source support in the HeaTiNG-02 test section with checks before and after the operation. (author)

Improving clinical cognitive testing: report of the AAN Behavioral Neurology Section Workgroup.

Science.gov (United States)

Daffner, Kirk R; Gale, Seth A; Barrett, A M; Boeve, Bradley F; Chatterjee, Anjan; Coslett, H Branch; D'Esposito, Mark; Finney, Glen R; Gitelman, Darren R; Hart, John J; Lerner, Alan J; Meador, Kimford J; Pietras, Alison C; Voeller, Kytja S; Kaufer, Daniel I

2015-09-08

To evaluate the evidence basis of single-domain cognitive tests frequently used by behavioral neurologists in an effort to improve the quality of clinical cognitive assessment. Behavioral Neurology Section members of the American Academy of Neurology were surveyed about how they conduct clinical cognitive testing, with a particular focus on the Neurobehavioral Status Exam (NBSE). In contrast to general screening cognitive tests, an NBSE consists of tests of individual cognitive domains (e.g., memory or language) that provide a more comprehensive diagnostic assessment. Workgroups for each of 5 cognitive domains (attention, executive function, memory, language, and spatial cognition) conducted evidence-based reviews of frequently used tests. Reviews focused on suitability for office-based clinical practice, including test administration time, accessibility of normative data, disease populations studied, and availability in the public domain. Demographic and clinical practice data were obtained from 200 respondents who reported using a wide range of cognitive tests. Based on survey data and ancillary information, between 5 and 15 tests in each cognitive domain were reviewed. Within each domain, several tests are highlighted as being well-suited for an NBSE. We identified frequently used single-domain cognitive tests that are suitable for an NBSE to help make informed choices about clinical cognitive assessment. Some frequently used tests have limited normative data or have not been well-studied in common neurologic disorders. Utilizing standardized cognitive tests, particularly those with normative data based on the individual's age and educational level, can enhance the rigor and utility of clinical cognitive assessment. © 2015 American Academy of Neurology.

Thermal response test data of five quadratic cross section precast pile heat exchangers.

Science.gov (United States)

Alberdi-Pagola, Maria

2018-06-01

This data article comprises records from five Thermal Response Tests (TRT) of quadratic cross section pile heat exchangers. Pile heat exchangers, typically referred to as energy piles, consist of traditional foundation piles with embedded heat exchanger pipes. The data presented in this article are related to the research article entitled "Comparing heat flow models for interpretation of precast quadratic pile heat exchanger thermal response tests" (Alberdi-Pagola et al., 2018) [1]. The TRT data consists of measured inlet and outlet temperatures, fluid flow and injected heat rate recorded every 10 min. The field dataset is made available to enable model verification studies.

A new laser reflectance system capable of measuring changing cross-sectional area of soft tissues during tensile testing.

Science.gov (United States)

Pokhai, Gabriel G; Oliver, Michele L; Gordon, Karen D

2009-09-01

Determination of the biomechanical properties of soft tissues such as tendons and ligaments is dependent on the accurate measurement of their cross-sectional area (CSA). Measurement methods, which involve contact with the specimen, are problematic because soft tissues are easily deformed. Noncontact measurement methods are preferable in this regard, but may experience difficulty in dealing with the complex cross-sectional shapes and glistening surfaces seen in soft tissues. Additionally, existing CSA measurement systems are separated from the materials testing machine, resulting in the inability to measure CSA during testing. Furthermore, CSA measurements are usually made in a different orientation, and with a different preload, prior to testing. To overcome these problems, a noncontact laser reflectance system (LRS) was developed. Designed to fit in an Instron 8872 servohydraulic test machine, the system measures CSA by orbiting a laser transducer in a circular path around a soft tissue specimen held by tissue clamps. CSA measurements can be conducted before and during tensile testing. The system was validated using machined metallic specimens of various shapes and sizes, as well as different sizes of bovine tendons. The metallic specimens could be measured to within 4% accuracy, and the tendons to within an average error of 4.3%. Statistical analyses showed no significant differences between the measurements of the LRS and those of the casting method, an established measurement technique. The LRS was successfully used to measure the changing CSA of bovine tendons during uniaxial tensile testing. The LRS developed in this work represents a simple, quick, and accurate way of reconstructing complex cross-sectional profiles and calculating cross-sectional areas. In addition, the LRS represents the first system capable of automatically measuring changing CSA of soft tissues during tensile testing, facilitating the calculation of more accurate biomechanical properties.

Review Report on the Design of In-Pile Test Section(IPS)

International Nuclear Information System (INIS)

Lee, Jong Min; Park, Kook Nam; Shim, Bong Sik; Lee, Chung Young; Chi, Dae Young; Park, Su Ki; Ahn, Sung Ho; Kim, Young Ki; Lee, Kye Hong; Kim, Kwan Hyun

2009-01-01

The In-Pile Test Section(IPS) accommodating fuel pins has loaded IR-1 hole in HANARO has double pressure vessel for the design conditions of 350 deg. C, 17.5 MPa and is composed of outer assembly and inner assembly. Dummy fuel, dummy fuel supports and Top flange are the main components in inner assembly and inner pressure vessel, outer pressure vessel and head are the components in outer assembly. The IPS at current status has dummy fuels and confirm the requirements for the IPS design improvements during the design, manufacturing and installation process. Head, Top Flange, Instrumentation Feed through, Lifting Eye, Fuel Carrier Leg, Retainer and Nozzle cover are the main parts that the design needs to be changed. This report suggest the needs for the IPS design modification and it would be reflected to the new IPS design which would accommodating test fuel pins

Review Report on the Design of In-Pile Test Section(IPS)

Energy Technology Data Exchange (ETDEWEB)

Lee, Jong Min; Park, Kook Nam; Shim, Bong Sik; Lee, Chung Young; Chi, Dae Young; Park, Su Ki; Ahn, Sung Ho; Kim, Young Ki; Lee, Kye Hong; Kim, Kwan Hyun

2009-01-15

The In-Pile Test Section(IPS) accommodating fuel pins has loaded IR-1 hole in HANARO has double pressure vessel for the design conditions of 350 deg. C, 17.5 MPa and is composed of outer assembly and inner assembly. Dummy fuel, dummy fuel supports and Top flange are the main components in inner assembly and inner pressure vessel, outer pressure vessel and head are the components in outer assembly. The IPS at current status has dummy fuels and confirm the requirements for the IPS design improvements during the design, manufacturing and installation process. Head, Top Flange, Instrumentation Feed through, Lifting Eye, Fuel Carrier Leg, Retainer and Nozzle cover are the main parts that the design needs to be changed. This report suggest the needs for the IPS design modification and it would be reflected to the new IPS design which would accommodating test fuel pins.

Accelerated load testing of geosynthetic base reinforced pavement test sections.

Science.gov (United States)

2011-02-01

The main objective of this research is to evaluate the benefits of geosynthetic stabilization and reinforcement of subgrade/base aggregate layers in flexible pavements built on weak subgrades and the effect of pre-rut pavement sections, prior to the ...

Test of virtual photon theory. [Cross sections, square-well potential, 0 to 300 MeV

Energy Technology Data Exchange (ETDEWEB)

Dressler, E T; Tomusiak, E L [Saskatchewan Univ., Saskatoon (Canada). Saskatchewan Accelerator Lab.

1976-11-30

In order to extract a photodisintegration cross section in the c.m. system from an electrodisintegration cross section measured in the lab system, one has to assume that the electrons are mostly scattered forward and that the monopole contributions are negligible. To test the validity of these approximations, a square well potential was assumed for the initial and final states and the photodisintegration cross section was calculated exactly within this model. These results were then compared with the results one would obtain using the virtual photon theory approximations for electron energies of 0-300 MeV and excitation energies up to 40 MeV. In comparing the two results, it is shown how and why the virtual photon theory approximations fail in certain kinematical regions.

77 FR 28281 - Withdrawal of Revocation of TSCA Section 4 Testing Requirements for One High Production Volume...

Science.gov (United States)

2012-05-14

... Withdrawal of Revocation of TSCA Section 4 Testing Requirements for One High Production Volume Chemical...]amino]- (CAS No. 1324-76-1), also known as C.I. Pigment Blue 61. EPA received an adverse comment regarding C.I. Pigment Blue 61. This document withdraws the revocation of testing requirements for C.I...

Testing of the IRDF-90 cross-section library in benchmark neutron spectra

International Nuclear Information System (INIS)

Nolthenius, H.J.; Zsolnay, E.M.; Szondi, E.J.

1993-09-01

The new version of the International Reactor Dosimetry File IRDF-90 (called ''Version April 1993'') has been tested by calculation of average cross-sections and their uncertainties in a coarse three energy group structure and by neutron spectrum adjustments in reference neutron spectra. This paper presents the results obtained and compares them with the corresponding ones of the old IRDF-85 and with the data of the Nuclear Data Guide for Reactor Neutron Metrology. The applicability of the new library in the field of neutron metrology is discussed. (orig.)

Longitudinal Acceleration Test of Overhead Luggage Bins and Auxiliary Fuel Tank in a Transport Airplane Airframe Section, Part 2

National Research Council Canada - National Science Library

McGuire, Robert

2000-01-01

This report contains the description and test results of overhead stowage bin calibrations and longitudinal impact testing of a 10-foot transport airframe section conducted at the Transportation Research Center Inc. (TRC...

Construction of a 2- by 2-foot transonic adaptive-wall test section at the NASA Ames Research Center

Science.gov (United States)

Morgan, Daniel G.; Lee, George

1986-01-01

The development of a new production-size, two-dimensional, adaptive-wall test section with ventilated walls at the NASA Ames Research Center is described. The new facility incorporates rapid closed-loop operation, computer/sensor integration, and on-line interference assessment and wall corrections. Air flow through the test section is controlled by a series of plenum compartments and three-way slide vales. A fast-scan laser velocimeter was built to measure velocity boundary conditions for the interference assessment scheme. A 15.2-cm- (6.0-in.-) chord NACA 0012 airfoil model will be used in the first experiments during calibration of the facility.

BUGLE-93 (ENDF/B-VI) cross-section library data testing using shielding benchmarks

International Nuclear Information System (INIS)

Hunter, H.T.; Slater, C.O.; White, J.E.

1994-01-01

Several integral shielding benchmarks were selected to perform data testing for new multigroup cross-section libraries compiled from the ENDF/B-VI data for light water reactor (LWR) shielding and dosimetry. The new multigroup libraries, BUGLE-93 and VITAMIN-B6, were studied to establish their reliability and response to the benchmark measurements by use of radiation transport codes, ANISN and DORT. Also, direct comparisons of BUGLE-93 and VITAMIN-B6 to BUGLE-80 (ENDF/B-IV) and VITAMIN-E (ENDF/B-V) were performed. Some benchmarks involved the nuclides used in LWR shielding and dosimetry applications, and some were sensitive specific nuclear data, i.e. iron due to its dominant use in nuclear reactor systems and complex set of cross-section resonances. Five shielding benchmarks (four experimental and one calculational) are described and results are presented

How do people respond to self-test results? A cross-sectional survey

Directory of Open Access Journals (Sweden)

de Vries Nanne K

2010-10-01

Full Text Available Abstract Background Self-tests, tests on medical conditions that can be performed by consumers without consulting a doctor first, are frequently used. Nevertheless, there are concerns about the safety of self-testing, as it may delay diagnosis and appropriate treatment in the case of inappropriate use of the test, or false-negative results. It is unclear whether self-tests stimulate appropriate follow-up behaviour. Our aim was to examine the frequency of self-test use, consumers' response to self-test results in terms of their confidence in the result, reassurance by the test result, and follow-up behaviour. Methods A two step cross-sectional survey was designed. A random sample of 6700 Internet users in an existing Internet panel received an online questionnaire on the use of self-tests. Self-tests were defined as tests on body materials, initiated by consumers with the aim to diagnose a disease or risk factor. A second questionnaire on consumers' response to self-test results was sent to the respondents that were identified as a self-tester in the first questionnaire (n = 703. Results 18.1% (799/4416 of the respondents had ever performed a self-test, the most frequently used tests being those for diabetes (5.3%, kidney disease (4.9%, cholesterol (4.5%, urinary tract infection (1.9% and HIV/AIDS and Chlamydia (both 1.6%. A total of 78.1% of the testers with a normal test result and 81.4% of those with an abnormal result reported confidence in this result. Almost all (95.6% of the testers with a normal result felt reassured. After a normal result, 78.1% did not take any further action and 5.8% consulted a doctor. The corresponding figures after an abnormal test result were 9.3% and 72.2%, respectively. Conclusions Respondents who had performed a self-test seemed to base their follow-up behaviour on the result of the test. They had confidence in the test result, and were often reassured by a normal result. After an abnormal result, most self

The relationship between Test Takers’ Multiple Intelligences and Their Performance on the Reading Sections of TOEFL and IELTS

Directory of Open Access Journals (Sweden)

Minoo Alemi

2010-04-01

Full Text Available The present study aimed at investigating the hypothetical relationship between the multiple intelligences of test takers and their performance on the reading sections of TOEFL and IELTS. Howard Gardner’s theory of multiple intelligences suggests that intelligence is not a single and solely inborn capacity, rather a multiple construct which is only partly genetic, and can be crystallized or paralyzed over one’s lifetime. Based on the theory, there are eight types of intelligence: linguistic, mathematical, musical, bodily, spatial, intrapersonal, interpersonal and naturalist, but the list is not exhaustive. The multiple intelligences of test takers were estimated by means of MIDAS, the Multiple Intelligences Developmental Assessment Scales, developed by Shearer (1994. Subsequently, the bias detection for the reading section of TOEFL was carried out on 90 participants, and this subtest was found to correlate positively with linguistic and logical intelligences. By the same token, 89 out of the 163 participants in the study were included in the analysis of the relationship between the multiple intelligences of test takers and their performance on the reading section of IELTS, and this test proved biased toward linguistic and spatial intelligences. The implications concern the inadequacy of the definition of language proficiency .Moreover, Measurement-Driven Instruction courses and preparatory materials of the two proficiency tests, TOEFL and IELTS, can benefit from the results of the study by being designed in such a way as to represent the intelligences which are positively correlated with performance on the tests in question.

IR1 flow tube and In-Pile Test Section Pressure drop test for the 3-Pin Fuel Test Loop

Energy Technology Data Exchange (ETDEWEB)

Lee, H. H.; Park, K. N.; Chi, D. Y.; Sim, B. S.; Park, S. K.; Lee, J. M.; Lee, C. Y.; Kim, H. N

2006-02-15

The in-pile Section (IPS) of 3-pin Fuel Test Loop(FTL) shall be installed in the vertical hole call IR1 of HANARO reactor core. In order to verify the pressure drop and flow rate both the inside region of IPS at the annular region between IPS and IR1 flow tube, a pressure drop was measured by varing the flow rate on both regions. The measured pressure drop in the annular region is 209kpa at 14.9kg/s which meets the limiting condition of operation of 200kpa. The measured pressure drop in side the IPS becomes 260.25kpa which is lower than the designed value of 306.65kpa. As the pressure drop is lower than the design value, it is quite conservative from the safety and operating point of view.

Feasibility of supervised self-testing using an oral fluid-based HIV rapid testing method: a cross-sectional, mixed method study among pregnant women in rural India

OpenAIRE

Sarkar, Archana; Mburu, Gitau; Shivkumar, Poonam Varma; Sharma, Pankhuri; Campbell, Fiona; Behera, Jagannath; Dargan, Ritu; Mishra, Surendra Kumar; Mehra, Sunil

2016-01-01

Introduction: HIV self-testing can increase coverage of essential HIV services. This study aimed to establish the acceptability, concordance and feasibility of supervised HIV self-testing among pregnant women in rural India. Methods: A cross-sectional, mixed methods study was conducted among 202 consenting pregnant women in a rural Indian hospital between August 2014 and January 2015. Participants were provided with instructions on how to self-test using OraQuick® HIV antibody test, and subse...

Measurement of single-top cross section and test of anomalous $Wtb$ coupling

Energy Technology Data Exchange (ETDEWEB)

Jung, Ji-Eun [Seoul National Univ. (Korea, Republic of)

2010-01-01

The top quark is most often produced in tt pairs via the strong interaction, however electroweak production of a singly-produced top quark is also possible. Electroweak single-top production is more difficult to observe than tt production. Studying single-top production is important for the following reasons. It provides direct measurement of the CKM matrix element and also single-top events are a background to several searches for SM or non-SM signals, such as Higgs boson searches. The information of spin polarization of top-quark can be used to t est anomalous W-t-b coupling. This thesis describes the result of a measurement of single-top cross-section and a test of anomalous W-t-b coupling using 4.8 f b^-1 of data collected by the CDF Run II experiment at the Fermilab Tevatron. The measured cross-section is 1.83$+0.7\\atop{-0.6}$ pb and measured limit of |Vtb| is 0.41 at 95% CL. The fraction of V+A coupling is 0 ± 28 (%).

Cap Bubble Drift Velocity in a Confined Test Section

International Nuclear Information System (INIS)

Xiaodong Sun; Seungjin Kim; Mamoru Ishii; Lincoln, Frank W.; Beus, Stephen G.

2002-01-01

In the two-group interfacial area transport equation, bubbles are categorized into two groups, i.e., spherical/distorted bubbles as group 1 and cap/slug/churn-turbulent bubbles as group 2. The bubble rise velocities for both groups of bubbles may be estimated by the drift flux model by applying different distribution parameters and drift velocities for both groups. However, the drift velocity for group 2 bubbles is not always applicable (when the wall effect becomes important) as in the current test loop of interest where the flow channel is confined by two parallel flat walls, with a dimension of 200-mm in width and 10-mm in gap. The previous experiments indicated that no stable slug flow existed in this test section, which was designed to permit visualization of the flow patterns and bubble characteristics without the distortion associated with curved surfaces. In fact, distorted cap bubbly and churn-turbulent flow was observed. Therefore, it is essential to developed a correlation for cap bubble drift velocity in this confined flow channel. Since the rise velocity of a cap bubble depends on its size, a high-speed movie camera is used to capture images of cap bubbles to obtain the bubble size information. Meanwhile, the rise velocity of cap and elongated bubbles (called cap bubbles hereafter) is investigated by examining the captured images frame by frame. As a result, the conventional correlation of drift velocity for slug bubbles is modified and acceptable agreements between the measurements and correlation estimation are achieved

Testing of cross section libraries for TRIGA criticality benchmark

International Nuclear Information System (INIS)

Snoj, L.; Trkov, A.; Ravnik, M.

2007-01-01

Influence of various up-to-date cross section libraries on the multiplication factor of TRIGA benchmark as well as the influence of fuel composition on the multiplication factor of the system composed of various types of TRIGA fuel elements was investigated. It was observed that keff calculated by using the ENDF/B VII cross section library is systematically higher than using the ENDF/B-VI cross section library. The main contributions (∼ 2 20 pcm) are from 235 U and Zr. (author)

HIV testing and tolerance to gender based violence: a cross-sectional study in Zambia.

Directory of Open Access Journals (Sweden)

Sara Gari

Full Text Available This paper explores the effect of social relations and gender-based conflicts on the uptake of HIV testing in the South and Central provinces of Zambia. We conducted a community-based cross-sectional study of 1716 randomly selected individuals. Associations were examined using mixed-effect multivariable logistic regression. A total of 264 men (64% and 268 women (56% had never tested for HIV. The strongest determinants for not being tested were disruptive couple relationships (OR = 2.48 95% CI = 1.00-6.19; tolerance to gender-based violence (OR = 2.10 95% CI = 1.05-4.32 and fear of social rejection (OR = 1.48 95% CI = 1.23-1.80. In the Zambian context, unequal power relationships within the couple and the community seem to play a pivotal role in the decision to test which until now have been largely underestimated. Policies, programs and interventions to rapidly increase HIV testing need to urgently address gender-power inequity in relationships and prevent gender-based violence to reduce the negative impact on the lives of couples and families.

Fracture toughness testing of core from the Cambro-Ordovician Section on the Oak Ridge Reservation

International Nuclear Information System (INIS)

Lemiszki, P.J.; Landes, J.D.

1996-01-01

The modified ring test was used to determine the mode I fracture toughness of bedrock cores from the DOE Oak Ridge Reservation in east Tennessee. Low porosity sandstones, limestones, and dolostones from the lower part of the Paleozoic section in Copper Creek and Whiteoak Mountain thrust sheets were sampled. In general, the average mode I fracture toughness decreases from sandstone, dolostone, and limestone. The fracture toughness of the limestones varies between rock units, which is related to different sedimentologic characteristics. Quality of results was evaluated by testing cores of Berea Sandstone and Indiana Limestone, which produced results similar to published results

Research and field tests of staged fracturing technology for casing deformation sections in horizontal shale gas wells

Directory of Open Access Journals (Sweden)

Shimeng Liao

2018-02-01

Full Text Available Horizontal shale gas well fracturing is mostly carried out by pumping bridge plugs. In the case of casing deformation, the bridge plug can not be pumped down to the designated position, so the hole sections below the deformation could not be stimulated according to the design program. About 30% of horizontal shale gas wells in the Changning and Weiyuan Blocks, Sichuan Basin, suffer various casing deformation after fracturing. Previously, the hole sections which could not be stimulated due to casing deformation were generally abandoned. As a result, the resources controlled by shale gas wells weren't exploited effectively and the fracturing effect was impacted greatly. There are a lot of difficulties in investigating casing deformation, such as complex mechanisms, various influencing factors and unpredictable deformation time. Therefore, it is especially important to seek a staged fracturing technology suitable for the casing deformation sections. In this paper, the staged fracturing technology with sand plugs inside fractures and the staged fracturing technology with temporary plugging balls were tested in casing deformation wells. The staged fracturing technology with sand plugs inside fractures was carried out in the mode of single-stage perforation and single-stage fracturing. The staged fracturing technology with temporary plugging balls was conducted in the mode of single perforation, continuous fracturing and staged ball dropping. Then, two kinds of technologies were compared in terms of their advantages and disadvantages. Finally, they were tested on site. According to the pressure response, the pressure monitoring of the adjacent wells and the microseismic monitoring in the process of actual fracturing, both technologies are effective in the stimulation of the casing deformation sections, realizing well control reserves efficiently and guaranteeing fracturing effects. Keywords: Shale gas, Horizontal well, Casing deformation, Staged

Damping test results for straight sections of 3-inch and 8-inch unpressurized pipes

International Nuclear Information System (INIS)

Ware, A.G.; Thinnes, G.L.

1984-04-01

EG and G Idaho is assisting the Nuclear Regulatory Commission and the Pressure Vessel Research Committee in supporting a final position on revised damping values for structural analyses of nuclear piping systems. As part of this program, a series of vibrational tests on unpressurized 3-in. and 8-in. Schedule 40 carbon steel piping was conducted to determine the changes in structural damping due to various parametric effects. The 33-ft straight sections of piping were supported at the ends. Additionally, intermediate supports comprising spring, rod, and constant-force hangers, as well as a sway brace and snubbers, were used. Excitation was provided by low-force-level hammer impacts, a hydraulic shaker, and a 50-ton overhead crane for snapback testing. Data was recorded using acceleration, strain, and displacement time histories. This report presents test results showing the effect of stress level and type of supports on structural damping in piping

Approximating a free-field blast environment in the test section of an explosively driven conical shock tube

Science.gov (United States)

Stewart, J. B.

2018-02-01

This paper presents experimental data on incident overpressures and the corresponding impulses obtained in the test section of an explosively driven 10° (full angle) conical shock tube. Due to the shock tube's steel walls approximating the boundary conditions seen by a spherical sector cut out of a detonating sphere of energetic material, a 5.3-g pentolite shock tube driver charge produces peak overpressures corresponding to a free-field detonation from an 816-g sphere of pentolite. The four test section geometries investigated in this paper (open air, cylindrical, 10° inscribed square frustum, and 10° circumscribed square frustum) provide a variety of different time histories for the incident overpressures and impulses, with a circumscribed square frustum yielding the best approximation of the estimated blast environment that would have been produced by a free-field detonation.

Texas flexible pavements and overlays : year 1 report, test sections, data collection, analyses, and data storage system.

Science.gov (United States)

2012-06-01

This five-year project was initiated to collect materials and pavement performance data on a minimum of 100 highway test sections around the State of Texas, incorporating both flexible pavements and overlays. Besides being used to calibrate and valid...

Testing Testing Testing.

Science.gov (United States)

Deville, Craig; O'Neill, Thomas; Wright, Benjamin D.; Woodcock, Richard W.; Munoz-Sandoval, Ana; Gershon, Richard C.; Bergstrom, Betty

1998-01-01

Articles in this special section consider (1) flow in test taking (Craig Deville); (2) testwiseness (Thomas O'Neill); (3) test length (Benjamin Wright); (4) cross-language test equating (Richard W. Woodcock and Ana Munoz-Sandoval); (5) computer-assisted testing and testwiseness (Richard Gershon and Betty Bergstrom); and (6) Web-enhanced testing…

Benchmark test of MORSE-DD code using double-differential form cross sections

International Nuclear Information System (INIS)

Nakagawa, Masayuki; Mori, Takamasa; Ishiguro, Yukio

1985-02-01

The multi-group double-differential form cross sections (DDX) and the three dimensional Monte Carlo code MORSE-DD devised to utilize the DDX, which were developed for the fusion neutronics analysis, have been validated through many benchmark tests. All the problems tested have a 14 MeV neutron source. To compare the calculated results with the measured values, the following experiments were adopted as the benchmark problems; leakage neutron spectra from spheres composed of nine kinds of materials measured at LLNL, neutron angular spectra from the Li 2 O slab measured at FNS in JAERI, tritium production rate (TPR) in the graphite-reflected Li 2 O sphere measured at FNS and the TPR in the metallic Li sphere measured at KfK. In addition in order to test an accuracy of the calculation method in detail, spectra of neutrons scattered from a small sample and various reaction rates in a Li 2 O cylinder were compared between the present method and the continuous energy Monte Carlo method. The nuclear data files used are mainly ENDF/B4 and partly JENDL-3PR1. The tests were carried out through a comparison with the measured values and also with the results obtained from the conventional Legendre expansion method and the continuous energy Monte Carlo method. It is found that the results by the present method are more accurate than those by the conventional one and agree well with those by the continuous energy Monte Carlo calculations. Discrepancies due to the nuclear data are also discussed. (author)

Geomaterial characterizations of full scale pavement test sections for mechanistic analysis and design

CSIR Research Space (South Africa)

Kwon, J

2007-02-01

Full Text Available roller compactor. The compaction effort was monitored with nuclear density gauge and DCP measurements taken from each pavement test section. As-built density of each subgrade lift obtained using the nuclear gauge satisfied a minimum relative density... was monitored with a nuclear gauge to maintain a minimum 95% relative compaction in the field. 0 100 200 300 400 500 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 CBR (%) Pe n et ra tio n (m m ) Pe n et ra tio n (m m ) Figure 2...

Evaluated cross section libraries

International Nuclear Information System (INIS)

Maqurno, B.A.

1976-01-01

The dosimetry tape (ENDF/B-IV tape 412) was issued in a general CSEWG distribution, August 1974. The pointwise cross section data file was tested with specified reference spectra. A group averaged cross section data file (620 groups based on tape 412) was tested with the above spectra and the results are presented in this report

Testing a self-determination theory model of children's physical activity motivation: a cross-sectional study.

Science.gov (United States)

Sebire, Simon J; Jago, Russell; Fox, Kenneth R; Edwards, Mark J; Thompson, Janice L

2013-09-26

Understanding children's physical activity motivation, its antecedents and associations with behavior is important and can be advanced by using self-determination theory. However, research among youth is largely restricted to adolescents and studies of motivation within certain contexts (e.g., physical education). There are no measures of self-determination theory constructs (physical activity motivation or psychological need satisfaction) for use among children and no previous studies have tested a self-determination theory-based model of children's physical activity motivation. The purpose of this study was to test the reliability and validity of scores derived from scales adapted to measure self-determination theory constructs among children and test a motivational model predicting accelerometer-derived physical activity. Cross-sectional data from 462 children aged 7 to 11 years from 20 primary schools in Bristol, UK were analysed. Confirmatory factor analysis was used to examine the construct validity of adapted behavioral regulation and psychological need satisfaction scales. Structural equation modelling was used to test cross-sectional associations between psychological need satisfaction, motivation types and physical activity assessed by accelerometer. The construct validity and reliability of the motivation and psychological need satisfaction measures were supported. Structural equation modelling provided evidence for a motivational model in which psychological need satisfaction was positively associated with intrinsic and identified motivation types and intrinsic motivation was positively associated with children's minutes in moderate-to-vigorous physical activity. The study provides evidence for the psychometric properties of measures of motivation aligned with self-determination theory among children. Children's motivation that is based on enjoyment and inherent satisfaction of physical activity is associated with their objectively-assessed physical

An Experimental Study of Natural Circulation in a Loop with Parallel Flow Test Sections

Energy Technology Data Exchange (ETDEWEB)

Mathisen, R P; Eklind, O

1965-10-15

The dynamic behaviour of a natural circulation loop parallel round duct channels has been studied. The test sections were both electrically heated and the power distribution was uniform along the 4300 mm heated length of the 20 mm dia. channels. The inter channel interference and the threshold of flow instability were obtained by using a dynamically calibrated flowmeter in each channel. The pressure was 50 bars and the sub-cooling 6 deg C. The main parameters varied, were the flow restrictions in the one-phase and two-phase sections. The instability data were correlated to the resistance coefficients due to these restrictions. Theoretical calculations for parallel channels in natural circulation have been compared with the experimental results. For the conditions determined by the above mentioned magnitudes, the steady-state computations are in excellent agreement with experiment. The transients are also nearly similar, except for the resonance frequency which for the theoretical case is higher by an amount between 0.3 and 0.5 c.p.s.

An Experimental Study of Natural Circulation in a Loop with Parallel Flow Test Sections

International Nuclear Information System (INIS)

Mathisen, R.P.; Eklind, O.

1965-10-01

The dynamic behaviour of a natural circulation loop parallel round duct channels has been studied. The test sections were both electrically heated and the power distribution was uniform along the 4300 mm heated length of the 20 mm dia. channels. The inter channel interference and the threshold of flow instability were obtained by using a dynamically calibrated flowmeter in each channel. The pressure was 50 bars and the sub-cooling 6 deg C. The main parameters varied, were the flow restrictions in the one-phase and two-phase sections. The instability data were correlated to the resistance coefficients due to these restrictions. Theoretical calculations for parallel channels in natural circulation have been compared with the experimental results. For the conditions determined by the above mentioned magnitudes, the steady-state computations are in excellent agreement with experiment. The transients are also nearly similar, except for the resonance frequency which for the theoretical case is higher by an amount between 0.3 and 0.5 c.p.s

Diagnostic and laboratory test ordering in Northern Portuguese Primary Health Care: a cross-sectional study

Science.gov (United States)

Sá, Luísa; Teixeira, Andreia Sofia Costa; Tavares, Fernando; Costa-Santos, Cristina; Couto, Luciana; Costa-Pereira, Altamiro; Hespanhol, Alberto Pinto; Santos, Paulo

2017-01-01

Objectives To characterise the test ordering pattern in Northern Portugal and to investigate the influence of context-related factors, analysing the test ordered at the level of geographical groups of family physicians and at the level of different healthcare organisations. Design Cross-sectional study. Setting Northern Primary Health Care, Portugal. Participants Records about diagnostic and laboratory tests ordered from 2035 family physicians working at the Northern Regional Health Administration, who served approximately 3.5 million Portuguese patients, in 2014. Outcomes To determine the 20 most ordered diagnostic and laboratory tests in the Northern Regional Health Administration; to identify the presence and extent of variations in the 20 most ordered diagnostic and laboratory tests between the Groups of Primary Care Centres and between health units; and to study factors that may explain these variations. Results The 20 most ordered diagnostic and laboratory tests almost entirely comprise laboratory tests and account for 70.9% of the total tests requested. We can trace a major pattern of test ordering for haemogram, glucose, lipid profile, creatinine and urinalysis. There was a significant difference (P<0.001) in test orders for all tests between Groups of Primary Care Centres and for all tests, except glycated haemoglobin (P=0.06), between health units. Generally, the Personalised Healthcare Units ordered more than Family Health Units. Conclusions The results from this study show that the most commonly ordered tests in Portugal are laboratory tests, that there is a tendency for overtesting and that there is a large variability in diagnostic and laboratory test ordering in different geographical and organisational Portuguese primary care practices, suggesting that there may be considerable potential for the rationalisation of test ordering. The existence of Family Health Units seems to be a strong determinant in decreasing test ordering by Portuguese family

Thermal response test data of five quadratic cross section precast pile heat exchangers

Directory of Open Access Journals (Sweden)

Maria Alberdi-Pagola

2018-06-01

Full Text Available This data article comprises records from five Thermal Response Tests (TRT of quadratic cross section pile heat exchangers. Pile heat exchangers, typically referred to as energy piles, consist of traditional foundation piles with embedded heat exchanger pipes. The data presented in this article are related to the research article entitled “Comparing heat flow models for interpretation of precast quadratic pile heat exchanger thermal response tests” (Alberdi-Pagola et al., 2018 [1]. The TRT data consists of measured inlet and outlet temperatures, fluid flow and injected heat rate recorded every 10 min. The field dataset is made available to enable model verification studies.

Testing for Helicobacter pylori in dyspeptic patients suspected of peptic ulcer disease in primary care: cross sectional study

NARCIS (Netherlands)

Weijnen, C. F.; Numans, M. E.; de Wit, N. J.; Smout, A. J.; Moons, K. G.; Verheij, T. J.; Hoes, A. W.

2001-01-01

OBJECTIVES: To develop an easily applicable diagnostic scoring method to determine the presence of peptic ulcers in dyspeptic patients in a primary care setting; to evaluate whether Helicobacter pylori testing adds value to history taking. Design: Cross sectional study. SETTING: General

Obstetrical correlates of the first time cesarean section, compared with the repeated cesarean section

International Nuclear Information System (INIS)

Rukh, G.; Akhtar, S.

2007-01-01

To determine the clinical and epidemiological characteristics in patients having their first cesarean section (FCS) and compare it with findings in patients with repeated cesarean section (RCS). This study included all the women who gave birth by cesarean sections, 817 of the total 5992 deliveries, at this unit during the study period. Data on potential risk factors for the first cesarean section (FCS) and repeated cesarean section (RCS were extracted from medical records, which were reviewed and compared between these two groups of women. Data were statistically analyzed with student t-test for comparison between means and Chi-square test for comparison between percentages. Crude odds ratio (OR) with 95% confidence interval (95% CI) were calculated. Significance was taken at p 0.05). The frequency of first cesarean section and repeat cesarean section is high in our setup. Adequate following of the programs to diminish the percentage of FCS by curtailing its predisposing factors is needed. (author)

Nucleate pool boiling investigation on a silicon test section with micro-fabricated cavities

International Nuclear Information System (INIS)

Sanna, A.; Kenning, D.B.R.; Karayiannis, T.G.; Hutter, C.; Sefiane, K.; Nelson, R.A.

2009-01-01

The basic mechanisms of nucleate boiling are still not completely understood, in spite of the many numerical and experimental studies dedicated to the topic. The use of a hybrid code allows reasonable computational times for simulations of a solid plate with a large population of artificial micro-cavities with fixed distribution. This paper analyses the guidelines for the design, through numerical simulations, of the location and sizes of micro-fabricated cavities on a new silicon test section immersed in FC-72 at the saturation temperature for different pressures with an imposed heat flux applied at the back of the plate. Particular focus is on variations of wall temperature around nucleation sites. (author)

Exploring the Effect of Teaching Test-Taking Strategies on Intermediate Level Learners on Reading Section of Ielts; Learners’ Attitude in Focus

Directory of Open Access Journals (Sweden)

Hooshang Khoshsima

2018-04-01

Full Text Available Language proficiency tests have become common instruments to judge people based on their performance. Thus, the scores on language proficiency tests, such as the International English Language Testing System (IELTS or Teaching English as a Foreign Language (TOEFL, play a crucial role in the test-takers’ lives. Because of increasing demands on the part of students to get a good score on these tests, test preparatory courses have emerged. These preparatory courses, characteristically short and limited in terms of time, equip IELTS candidates with the skills required for passing the test, called test-taking strategies. The present study explored the effect of strategy teaching- namely wash-back effect on reading section of academic IELTS on intermediate learners in Iran. Besides, learners’ attitude toward the strategy teaching was investigated as well. According to the descriptive statistics and t-test results, those learners who received strategy teaching outperformed those who had not received strategy teaching in reading section of IELTS.According to t-test results, there was a significant difference between the mean scores of the two groups since the p value was lower than .05 (p < .001.  Furthermore, the learners had positive attitudes toward receiving strategy teaching since there was a significant difference between the obtained mean score and the presupposed average because the p value was lower than .05.

Heat transfer in the in-pile test section and penetration region of 3-pin fuel test loop

Energy Technology Data Exchange (ETDEWEB)

Chi, Dae Young; Lee, Chung Young; Sim, Bong Shick; Park, Kook Nam; Park, Su Ki; Lee, Jong Min; Kim, Young Jin

2003-12-01

This report studies two types of normal heat transfer. One is the heat loss from the pressure vessel of In-Pile Test Section to HANARO pool water via IPS insulation gas gap. The other is the heat transfer of the Penetration Cooling Water System including the effect of the Foamglas insulator at the penetration region. The heat transfer from IPS insulation gas gap has been performed according to the detail design results from NUKEM. The heat loss also occurs at the concrete penetration region between the HANARO pool water and the FTL pipe gallery. The Foamglas insulator has been already installed at the MCW piping of the penetration region. This insulation effect has been reviewed. The Penetration Cooling Water System has been designed to fulfill the design requirement not to exceed the allowable temperature at the penetration concrete wall. The cooling ability and heat loss of PCW system has been reviewed with the insulation effect.

Testing a self-determination theory model of children’s physical activity motivation: a cross-sectional study

Science.gov (United States)

2013-01-01

Background Understanding children’s physical activity motivation, its antecedents and associations with behavior is important and can be advanced by using self-determination theory. However, research among youth is largely restricted to adolescents and studies of motivation within certain contexts (e.g., physical education). There are no measures of self-determination theory constructs (physical activity motivation or psychological need satisfaction) for use among children and no previous studies have tested a self-determination theory-based model of children’s physical activity motivation. The purpose of this study was to test the reliability and validity of scores derived from scales adapted to measure self-determination theory constructs among children and test a motivational model predicting accelerometer-derived physical activity. Methods Cross-sectional data from 462 children aged 7 to 11 years from 20 primary schools in Bristol, UK were analysed. Confirmatory factor analysis was used to examine the construct validity of adapted behavioral regulation and psychological need satisfaction scales. Structural equation modelling was used to test cross-sectional associations between psychological need satisfaction, motivation types and physical activity assessed by accelerometer. Results The construct validity and reliability of the motivation and psychological need satisfaction measures were supported. Structural equation modelling provided evidence for a motivational model in which psychological need satisfaction was positively associated with intrinsic and identified motivation types and intrinsic motivation was positively associated with children’s minutes in moderate-to-vigorous physical activity. Conclusions The study provides evidence for the psychometric properties of measures of motivation aligned with self-determination theory among children. Children’s motivation that is based on enjoyment and inherent satisfaction of physical activity is

Damping test results for straight sections of 3-inch and 8-inch unpressurized pipes. [PWR; BWR

Energy Technology Data Exchange (ETDEWEB)

Ware, A.G.; Thinnes, G.L.

1984-04-01

EG and G Idaho is assisting the Nuclear Regulatory Commission and the Pressure Vessel Research Committee in supporting a final position on revised damping values for structural analyses of nuclear piping systems. As part of this program, a series of vibrational tests on unpressurized 3-in. and 8-in. Schedule 40 carbon steel piping was conducted to determine the changes in structural damping due to various parametric effects. The 33-ft straight sections of piping were supported at the ends. Additionally, intermediate supports comprising spring, rod, and constant-force hangers, as well as a sway brace and snubbers, were used. Excitation was provided by low-force-level hammer impacts, a hydraulic shaker, and a 50-ton overhead crane for snapback testing. Data was recorded using acceleration, strain, and displacement time histories. This report presents test results showing the effect of stress level and type of supports on structural damping in piping.

Seismic analysis of the in-pile test section

Energy Technology Data Exchange (ETDEWEB)

Lee, J. M.; Park, K. N.; Chi, D. Y.; Park, S. K.; Sim, B. S.; Ahn, S. H.; Lee, C. Y.; Kim, Y. J. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

2004-07-01

This study gives the results of the seismic analysis of the IPS (In Pile Section) with lower bracket support. The results cover the natural frequency and seismic response of the IPS for the SSE and OBE events. An FE (Finite Element) model which includes the two vessels of the IPS and its support structure were analyzed by ABAQUS.

Wall adjustment strategy software for use with the NASA Langley 0.3-meter transonic cryogenic tunnel adaptive wall test section

Science.gov (United States)

Wolf, Stephen W. D.

1988-01-01

The Wall Adjustment Strategy (WAS) software provides successful on-line control of the 2-D flexible walled test section of the Langley 0.3-m Transonic Cryogenic Tunnel. This software package allows the level of operator intervention to be regulated as necessary for research and production type 2-D testing using and Adaptive Wall Test Section (AWTS). The software is designed to accept modification for future requirements, such as 3-D testing, with a minimum of complexity. The WAS software described is an attempt to provide a user friendly package which could be used to control any flexible walled AWTS. Control system constraints influence the details of data transfer, not the data type. Then this entire software package could be used in different control systems, if suitable interface software is available. A complete overview of the software highlights the data flow paths, the modular architecture of the software and the various operating and analysis modes available. A detailed description of the software modules includes listings of the code. A user's manual is provided to explain task generation, operating environment, user options and what to expect at execution.

Cross-sectional study of serum antibodies against Sarcocystis neurona in cats tested for antibodies against Toxoplasma gondii.

Science.gov (United States)

Rossano, Mary G; Murphy, Alice J; Vrable, Ruth A; Vanzo, Nicole E; Lewis, Stacy K; Sheline, Katherine D; Kaneene, John B; Mansfield, Linda S

2002-08-15

To determine apparent seroprevalence of antibodies against Sarcocystis neurona in a population of domestic cats previously tested for antibodies against Toxoplasma gondii. Cross-sectional study. Serum from 196 domestic cats. Banked serum samples submitted to the Michigan State University Animal Health Diagnostic Laboratory for T. gondii diagnostic testing were tested for antibodies against S. neurona by use of an indirect fluorescent antibody (IFA) test and a western blot test. Submission records were analyzed to determine descriptive statistics and test for associations between positive results of a test for S. neurona and other variables in the data set. 10 of 196 (5%) samples yielded positive results for antibodies against S. neurona by use of western blot analysis, whereas 27 samples yielded positive results by use of the IFA. No association was found between S. neurona western blot test results and T. gondii test results, age, sex, or the reason for T. gondii testing. The S. neurona IFA titer was positively and significantly associated with positive results of western blot analysis. Domestic cats are not likely to play a substantial role as intermediate hosts in the natural life cycle of S. neurona. Results indicate that natural infection of domestic cats may occur, and small animal practitioners should be aware of this fact when evaluating cats with neurologic disease. The S. neurona IFA test had lower specificity than western blot analysis.

Test of the universal rise of hadronic total cross sections at super-high energies

International Nuclear Information System (INIS)

Ishida, Muneyuki; Igi, Keiji

2007-01-01

The increase of the total cross sections at very high energies described by log 2 (s/s 0 ) appears to be confirmed. In the analysis of the COMPETE collaboration in the Particle Data Group (2006), the Blog 2 (s/s 0 ) was assumed to extend the universal rise of all the total hadronic cross sections to reduce the number of adjustable parameters. We test if the assumption on the universality of B is justified, through investigation of the values of B for π ± p(K ± p) and pp,pp scatterings. We search for the simultaneous best fit to the σ tot and ρ ratios, using a constraint from the FESR of the P' type for π -+ p scatterings and constraints that are free from the unphysical regions for the pp, pp and K ± p scatterings. By including rich information of the low-energy scattering data owing to the use of FESR, the errors of the B parameters decrease especially for πp. The resulting value of B pp is consistent with B πp within two standard deviations, which appears to support the universality hypothesis. (orig.)

Section Preequating under the Equivalent Groups Design without IRT

Science.gov (United States)

Guo, Hongwen; Puhan, Gautam

2014-01-01

In this article, we introduce a section preequating (SPE) method (linear and nonlinear) under the randomly equivalent groups design. In this equating design, sections of Test X (a future new form) and another existing Test Y (an old form already on scale) are administered. The sections of Test X are equated to Test Y, after adjusting for the…

Portuguese Family Physicians' Awareness of Diagnostic and Laboratory Test Costs: A Cross-Sectional Study.

Directory of Open Access Journals (Sweden)

Luísa Sá

Full Text Available Physicians' ability to make cost-effective decisions has been shown to be affected by their knowledge of health care costs. This study assessed whether Portuguese family physicians are aware of the costs of the most frequently prescribed diagnostic and laboratory tests.A cross-sectional study was conducted in a representative sample of Portuguese family physicians, using computer-assisted telephone interviews for data collection. A Likert scale was used to assess physician's level of agreement with four statements about health care costs. Family physicians were also asked to estimate the costs of diagnostic and laboratory tests. Each physician's cost estimate was compared with the true cost and the absolute error was calculated.One-quarter (24%; 95% confidence interval: 23%-25% of all cost estimates were accurate to within 25% of the true cost, with 55% (95% IC: 53-56 overestimating and 21% (95% IC: 20-22 underestimating the true actual cost. The majority (76% of family physicians thought they did not have or were uncertain as to whether they had adequate knowledge of diagnostic and laboratory test costs, and only 7% reported receiving adequate education. The majority of the family physicians (82% said that they had adequate access to information about the diagnostic and laboratory test costs. Thirty-three percent thought that costs did not influence their decision to order tests, while 27% were uncertain.Portuguese family physicians have limited awareness of diagnostic and laboratory test costs, and our results demonstrate a need for improved education in this area. Further research should focus on identifying whether interventions in cost knowledge actually change ordering behavior, in identifying optimal methods to disseminate cost information, and on improving the cost-effectiveness of care.

Portuguese Family Physicians’ Awareness of Diagnostic and Laboratory Test Costs: A Cross-Sectional Study

Science.gov (United States)

Sá, Luísa; Costa-Santos, Cristina; Teixeira, Andreia; Couto, Luciana; Costa-Pereira, Altamiro; Hespanhol, Alberto; Santos, Paulo; Martins, Carlos

2015-01-01

Background Physicians’ ability to make cost-effective decisions has been shown to be affected by their knowledge of health care costs. This study assessed whether Portuguese family physicians are aware of the costs of the most frequently prescribed diagnostic and laboratory tests. Methods A cross-sectional study was conducted in a representative sample of Portuguese family physicians, using computer-assisted telephone interviews for data collection. A Likert scale was used to assess physician’s level of agreement with four statements about health care costs. Family physicians were also asked to estimate the costs of diagnostic and laboratory tests. Each physician’s cost estimate was compared with the true cost and the absolute error was calculated. Results One-quarter (24%; 95% confidence interval: 23%–25%) of all cost estimates were accurate to within 25% of the true cost, with 55% (95% IC: 53–56) overestimating and 21% (95% IC: 20–22) underestimating the true actual cost. The majority (76%) of family physicians thought they did not have or were uncertain as to whether they had adequate knowledge of diagnostic and laboratory test costs, and only 7% reported receiving adequate education. The majority of the family physicians (82%) said that they had adequate access to information about the diagnostic and laboratory test costs. Thirty-three percent thought that costs did not influence their decision to order tests, while 27% were uncertain. Conclusions Portuguese family physicians have limited awareness of diagnostic and laboratory test costs, and our results demonstrate a need for improved education in this area. Further research should focus on identifying whether interventions in cost knowledge actually change ordering behavior, in identifying optimal methods to disseminate cost information, and on improving the cost-effectiveness of care. PMID:26356625

Community engagement in sexual health and uptake of HIV testing and syphilis testing among MSM in China: a cross-sectional online survey.

Science.gov (United States)

Zhang, Tiange P; Liu, Chuncheng; Han, Larry; Tang, Weiming; Mao, Jessica; Wong, Terrence; Zhang, Ye; Tang, Songyuan; Yang, Bin; Wei, Chongyi; Tucker, Joseph D

2017-04-03

HIV and syphilis testing rates remain low among men who have sex with men (MSM) in low- and middle-income countries (LMICs). Community engagement has been increasingly used to promote HIV testing among key populations in high-income countries, often in settings with stronger civil society. This study aimed to assess socio-demographic, behavioural, and community engagement factors associated with HIV and syphilis testing among MSM in China. MSM ≥16 years old who had condomless sex in the past three months were recruited nationwide to complete a cross-sectional online survey in November 2015. Data were collected on socio-demographics, sexual behaviours, HIV testing, syphilis testing, and community engagement in sexual health. We defined community engagement in sexual health using six items assessing awareness and advocacy of sexual health programmes. The underlying factor structure of a 6-item community engagement scale was determined through exploratory factor analysis. Univariate and multivariable logistic regressions identified correlates of HIV and syphilis testing. 1189 MSM were recruited. 54% (647/1189) of men had ever tested for HIV and 30% (354/1189) had ever tested for syphilis. Factor analysis suggested three levels of community engagement (minimal, moderate, and substantial) and this model explained 79.5% of observed variance. A quarter (26%, 312/1189) reported none to minimal engagement, over one half (54%, 644/1189) reported moderate engagement, and a fifth (20%, 233/1189) reported substantial engagement. Multivariable logistic regression showed that MSM with greater community engagement in sexual health were more likely to have ever tested for HIV (substantial vs. no engagement: aOR 7.91, 95% CI 4.98-12.57) and for syphilis (substantial vs. no engagement: aOR 5.35, 95% CI 3.16-9.04). HIV and syphilis testing are suboptimal among MSM in China. Community engagement may be useful for promoting testing in China and should be considered in intervention

Investigating the Value of Section Scores for the "TOEFL iBT"® Test. "TOEFL iBT"® Research Report. TOEFL iBT-21. ETS Research Report RR-13-35

Science.gov (United States)

Sawaki, Yasuyo; Sinharay, Sandip

2013-01-01

This study investigates the value of reporting the reading, listening, speaking, and writing section scores for the "TOEFL iBT"® test, focusing on 4 related aspects of the psychometric quality of the TOEFL iBT section scores: reliability of the section scores, dimensionality of the test, presence of distinct score profiles, and the…

Computational simulation of the natural circulation occurring in an experimental test section of a pool type research reactor

Energy Technology Data Exchange (ETDEWEB)

Nascimento, Francisco R.T. do; Lima Junior, Carlos A.S.; Oliveira, Andre F.S. de; Affonso, Renato R.W.; Faccini, Jose L.H.; Moreira, Maria L., E-mail: rogerio.tdn@gmail.com, E-mail: souzalima_ca@ien.gov.br, E-mail: oliveira.afelipe@gmail.com, E-mail: raoniwa@yahoo.com.br, E-mail: faccini@ien.gov.br, E-mail: malu@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

2015-07-01

The present work presents a computational simulation of the natural circulation phenomenon developing in an experimental test section of a pool type research reactor. The test section has been designed using a reduced scale in height 1:4.7 in relation to a pool type 30 MW research reactor prototype. It comprises a cylindrical vessel, which is opened to atmosphere, and representing the reactor pool; a natural circulation pipe, a lower plenum, and a heater containing electrical resistors in rectangular plate format, which represents the fuel elements, with a chimney positioned on the top of the resistor assembly. In the computational simulation, it was used a commercial CFD software, without any turbulence model. Besides, in the presence of the natural circulation, a laminar flow has been assumed and the equations of the mass conservation, momentum and energy were solved by the finite element method. In addition, the results of the simulation are presented in terms of velocities and temperatures differences, respectively: at inlet and outlet of the heater and of the natural circulation pipe. (author)

Computational simulation of the natural circulation occurring in an experimental test section of a pool type research reactor

International Nuclear Information System (INIS)

Nascimento, Francisco R.T. do; Lima Junior, Carlos A.S.; Oliveira, Andre F.S. de; Affonso, Renato R.W.; Faccini, Jose L.H.; Moreira, Maria L.

2015-01-01

The present work presents a computational simulation of the natural circulation phenomenon developing in an experimental test section of a pool type research reactor. The test section has been designed using a reduced scale in height 1:4.7 in relation to a pool type 30 MW research reactor prototype. It comprises a cylindrical vessel, which is opened to atmosphere, and representing the reactor pool; a natural circulation pipe, a lower plenum, and a heater containing electrical resistors in rectangular plate format, which represents the fuel elements, with a chimney positioned on the top of the resistor assembly. In the computational simulation, it was used a commercial CFD software, without any turbulence model. Besides, in the presence of the natural circulation, a laminar flow has been assumed and the equations of the mass conservation, momentum and energy were solved by the finite element method. In addition, the results of the simulation are presented in terms of velocities and temperatures differences, respectively: at inlet and outlet of the heater and of the natural circulation pipe. (author)

Analysis of benchmark experiments for testing the IKE multigroup cross-section libraries based on ENDF/B-III and IV

International Nuclear Information System (INIS)

Keinert, J.; Mattes, M.

1975-01-01

Benchmark experiments offer the most direct method for validation of nuclear cross-section sets and calculational methods. For 16 fast and thermal critical assemblies containing uranium and/or plutonium of different compositions we compared our calculational results with measured integral quantities, such as ksub(eff), central reaction rate ratios or fast and thermal activation (dis)advantage factors. Cause of the simple calculational modelling of these assemblies the calculations proved as a good test for the IKE multigroup cross-section libraries essentially based on ENDF/B-IV. In general, our calculational results are in excellent agreement with the measured values. Only with some critical systems the basic ENDF/B-IV data proved to be insufficient in calculating ksub(eff), probably due to Pu neutron data and U 238 fast capture cross-sections. (orig.) [de

Three-section expiratory CT

DEFF Research Database (Denmark)

Loeve, Martine; de Bruijne, Marleen; Hartmann, Ieneke C. J.

2012-01-01

. Longitudinal follow-up was performed with three sections. All images were deidentified and randomized, and TA was scored with the Brody II system and a new quantitative system. Statistical analysis included the Wilcoxon signed rank test, calculation of Spearman and intraclass correlation coefficients, and use......Purpose: To estimate the effect of the number of computed tomography (CT) sections on trapped air (TA) assessment in patients with cystic fibrosis (CF) by using an established scoring system and a new quantitative scoring system and to compare CT and pulmonary function test (PFT) estimates of TA...

Low upper-shelf toughness, high transition temperature test insert in HSST [Heavy Section Steel Technology] PTSE-2 [Pressurized Thermal Shock Experiment-2] vessel and wide plate test specimens: Final report

International Nuclear Information System (INIS)

Domian, H.A.

1987-02-01

A piece of A387, Grade 22 Class 2 (2-1/4 Cr - 1 Mo) steel plate specially heat treated to produce low upper-shelf (LUS) toughness and high transition temperature was installed in the side wall of Heavy Section Steel Technology (HHST) vessel V-8. This vessel is to be tested by the Oak Ridge National Laboratory (ORNL) in the Pressurized Thermal Shock Experiment-2 (PTSE-2) project of the HSST program. Comparable pieces of the plate were made into six wide plate specimens and other samples. These samples underwent tensile tests, Charpy tests, and J-integral tests. The results of these tests are given in this report

Feasibility of supervised self-testing using an oral fluid-based HIV rapid testing method: a cross-sectional, mixed method study among pregnant women in rural India.

Science.gov (United States)

Sarkar, Archana; Mburu, Gitau; Shivkumar, Poonam Varma; Sharma, Pankhuri; Campbell, Fiona; Behera, Jagannath; Dargan, Ritu; Mishra, Surendra Kumar; Mehra, Sunil

2016-01-01

HIV self-testing can increase coverage of essential HIV services. This study aimed to establish the acceptability, concordance and feasibility of supervised HIV self-testing among pregnant women in rural India. A cross-sectional, mixed methods study was conducted among 202 consenting pregnant women in a rural Indian hospital between August 2014 and January 2015. Participants were provided with instructions on how to self-test using OraQuick(®) HIV antibody test, and subsequently asked to self-test under supervision of a community health worker. Test results were confirmed at a government-run integrated counselling and testing centre. A questionnaire was used to obtain information on patient demographics and the ease, acceptability and difficulties of self-testing. In-depth interviews were conducted with a sub-sample of 35 participants to understand their experiences. In total, 202 participants performed the non-invasive, oral fluid-based, rapid test under supervision for HIV screening. Acceptance rate was 100%. Motivators for self-testing included: ease of testing (43.4%), quick results (27.3%) and non-invasive procedure (23.2%). Sensitivity and specificity were 100% for 201 tests, and one test was invalid. Concordance of test result interpretation between community health workers and participants was 98.5% with a Cohen's Kappa (k) value of k=0.566 with pwomen in rural India. Participants were supportive of making self-testing publicly available. Policy guidelines and implementation research are required to advance HIV self-testing for larger populations at scale.

Design modification of the in-pile test section for increase of sealing capability

Energy Technology Data Exchange (ETDEWEB)

Hong, J T; Ahn, S H; Joung, C Y; Jeong, H Y; Lee, J M; Sim, B S [Department of Research Reactor Utilization and Development, Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

2012-03-15

Since KAERI established the fuel test loop (FTL) at HANARO in 2009, KAERI has carried out several experiments to verify the performances of the equipment. Based on the experiments, the design modification of the In-Pile test Section (IPS) has been processed to improve some difficulties such as difficulty in ejecting the inner assembly of the IPS from the pressure vessel, difficulty of the sealing process of the cooling water, etc. At first, because the cooling water of HANARO in KAERI consists of an open-pool type, if a certain shock is generated during the disassembly process, the cooling water can be spattered out of the pool. Therefore, two jacking bolts will be added on the top flange part of the inner assembly to decrease the shock. Second, at the pressure boundary of the IPS where MI-cables go through, the brazing process has been used to seal out the cooling water. However, because the length of the IPS is up to 5.5 meters, it is too difficult and time consuming to carry out the brazing process at the end part of the IPS. Therefore, the brazing process will be replaced with the mechanical sealing structure to simplify the assembly process. (author)

Operation and post operative examinations on the 1 MW test section SDP-1

International Nuclear Information System (INIS)

Casalini, P.; Valentini, P.; Urbani, A.

1975-01-01

The tests carried out were essentially, of general interest and could regard the general Performance and the behavior of the materials. The last aspect was rather interesting as the steam generator coil consists of a steel which has not been yet homologated in Italy. As already specified, the geometry of the steam generator was somewhat particular: it consisted of a stainless steel (Type AISI 316) cylindrical envelope with a diameter of about 500 mm and about 4 m high, with inside an helicoidal duct having a rectangular section, also in AISI 316 stainless steel. Three helicoidal tubes with an outer diameter of 26,9 mm and a thickness of 5 mm, out of ferritic steel - Type Mannesman F 11 were arranged inside the duct. The rectangular duct was run through by sodium downwards, while water/steam was running through the three parallel tubes upwards. The main characteristics pertaining to the steam generator and the nominal operational data are given. All the tests carried out on the tube coil resulted in noticeable alteration due to operation in sodium. In particular, with regard to the absence of variation of the carbon content between the inner and outer side in all the specimens analyzed, one can conclude that no considerable mass transfer occurred in the tube

What do Key Stakeholders Think About HIV Self-Testing in Canada? Results from a Cross-Sectional Survey.

Science.gov (United States)

Pai, N Pant; Smallwood, M; Gulati, D; Lapczak, N; Musten, A; Gaydos, C; Johnston, C; Steben, M; Wong, T; Engel, N; Kim, J

2018-02-01

Human immunodeficiency virus (HIV) self-testing presents an empowering alternative to facility-based testing for reaching undiagnosed HIV infected individuals, but is not currently available in Canada. We surveyed stakeholders (clinical providers, public health professionals, researchers) engaged in HIV testing initiatives nationwide to identify the concerns, opportunities and challenges to implementing HIV self-testing in Canada. An online cross-sectional survey was disseminated by the Canadian Institutes of Health Research Centre for REACH 2.0 National HIV & sexually transmitted and blood borne infections working group to stakeholders nationwide, with a target sample size of 200. Quantitative and qualitative data were analyzed using a mixed-methods, respondent-informed approach, to inform subsequent HIV self-testing in a country where self-testing is not yet accessible. A total of 183 responses were received. A majority (70.7%) (128/181) felt that self-testing was a necessary investment to reach the undiagnosed. 64.6% (117/181) felt that self-tests should be made available to their clients and 71.5% (128/179) of respondents agreed that self-test instructions required improvements. However, 50% (90/180) felt that self-testing will pose an economic challenge to current HIV testing models. Regardless, 21% urged for timely action and availability of HIV self-tests. Thematic analyses reflected the following concerns: (a) need for affordable self-tests, (b) need for expedited, customized, and accessible linkages to counselling, (c) concern for patients to cope with positive self-test results, (d) accuracy of self-tests to detect acute HIV and (e) liability in the context of non-disclosure. Stakeholders agreed to the provision of an option of HIV self-testing to reach the undiagnosed individuals. Concerns regarding costs and accuracy of self-tests, expedited linkages to counselling, and integration of self-test within prevailing HIV testing models, will need to be

Work-related stress is associated with impaired neuropsychological test performance: a clinical cross-sectional study.

Science.gov (United States)

Eskildsen, Anita; Andersen, Lars Peter; Pedersen, Anders Degn; Vandborg, Sanne Kjær; Andersen, Johan Hviid

2015-01-01

Patients on sick leave due to work-related stress often complain about impaired concentration and memory. However, it is undetermined how widespread these impairments are, and which cognitive domains are most long-term stress sensitive. Previous studies show inconsistent results and are difficult to synthesize. The primary aim of this study was to examine whether patients with work-related stress complaints have cognitive impairments compared to a matched control group without stress. Our secondary aim was to examine whether the level of self-reported perceived stress is associated with neuropsychological test performance. We used a broad neuropsychological test battery to assess 59 outpatients with work-related stress complaints (without major depression) and 59 healthy controls. We matched the patients and controls pairwise by sex, age and educational level. Compared to controls, patients generally showed mildly reduced performance across all the measured domains of the neuropsychological test battery. However, only three comparisons reached statistical significance (p working memory. There were no statistical significant associations between self-reported perceived stress level and neuropsychological test performance. In conclusion, we recommend that cognitive functions should be considered when evaluating patients with work-related stress complaints, especially when given advice regarding return to work. Since this study had a cross-sectional design, it is still uncertain whether the impairments are permanent. Further study is required to establish causal links between work-related stress and cognitive deficits.

Home-based HIV testing for men preferred over clinic-based testing by pregnant women and their male partners, a nested cross-sectional study.

Science.gov (United States)

Osoti, Alfred Onyango; John-Stewart, Grace; Kiarie, James Njogu; Barbra, Richardson; Kinuthia, John; Krakowiak, Daisy; Farquhar, Carey

2015-07-30

Male partner HIV testing and counseling (HTC) is associated with enhanced uptake of prevention of mother-to-child HIV transmission (PMTCT), yet male HTC during pregnancy remains low. Identifying settings preferred by pregnant women and their male partners may improve male involvement in PMTCT. Participants in a randomized clinical trial (NCT01620073) to improve male partner HTC were interviewed to determine whether the preferred male partner HTC setting was the home, antenatal care (ANC) clinic or VCT center. In this nested cross sectional study, responses were evaluated at baseline and after 6 weeks. Differences between the two time points were compared using McNemar's test and correlates of preference were determined using logistic regression. Among 300 pregnant female participants, 54% preferred home over ANC clinic testing (34.0%) or VCT center (12.0%). Among 188 male partners, 68% preferred home-based HTC to antenatal clinic (19%) or VCT (13%). Men who desired more children and women who had less than secondary education or daily income Pregnant women and their male partners preferred home-based compared to clinic or VCT-center based male partner HTC. Home-based HTC during pregnancy appears acceptable and may improve male testing and involvement in PMTCT.

The development of a capability for aerodynamic testing of large-scale wing sections in a simulated natural rain environment

Science.gov (United States)

Bezos, Gaudy M.; Cambell, Bryan A.; Melson, W. Edward

1989-01-01

A research technique to obtain large-scale aerodynamic data in a simulated natural rain environment has been developed. A 10-ft chord NACA 64-210 wing section wing section equipped with leading-edge and trailing-edge high-lift devices was tested as part of a program to determine the effect of highly-concentrated, short-duration rainfall on airplane performance. Preliminary dry aerodynamic data are presented for the high-lift configuration at a velocity of 100 knots and an angle of attack of 18 deg. Also, data are presented on rainfield uniformity and rainfall concentration intensity levels obtained during the calibration of the rain simulation system.

Involving women in personalised decision-making on mode of delivery after caesarean section: the development and pilot testing of a patient decision aid.

Science.gov (United States)

Schoorel, E N C; Vankan, E; Scheepers, H C J; Augustijn, B C C; Dirksen, C D; de Koning, M; van Kuijk, S M J; Kwee, A; Melman, S; Nijhuis, J G; Aardenburg, R; de Boer, K; Hasaart, T H M; Mol, B W J; Nieuwenhuijze, M; van Pampus, M G; van Roosmalen, J; Roumen, F J M E; de Vries, R; Wouters, M G A J; van der Weijden, T; Hermens, R P M G

2014-01-01

To develop a patient decision aid (PtDA) for mode of delivery after caesarean section that integrates personalised prediction of vaginal birth after caesarean (VBAC) with the elicitation of patient preferences and evidence-based information. A PtDA was developed and pilot tested using the International Patients Decision Aid Standards (IPDAS) criteria. Obstetric health care in the Netherlands. A multidisciplinary steering group, an expert panel, and 25 future users of the PtDA, i.e. women with a previous caesarean section. The development consisted of a construction phase (definition of scope and purpose, and selection of content, framework, and format) and a pilot testing phase by interview. The process was supervised by a multidisciplinary steering group. Usability, clarity, and relevance. The construction phase resulted in a booklet including unbiased balanced information on mode of birth after caesarean section, a preference elicitation exercise, and tailored risk information, including a prediction model for successful VBAC. During pilot testing, visualisation of risks and clarity formed the main basis for revisions. Pilot testing showed the availability of tailored structured information to be the main factor involving women in decision-making. The PtDA meets 39 out of 50 IPDAS criteria (78%): 23 out of 23 criteria for content (100%) and 16 out of 20 criteria for the development process (80%). Criteria for effectiveness (n = 7) were not evaluated. An evidence-based PtDA was developed, with the probability of successful VBAC and the availability of structured information as key items. It is likely that the PtDA enhances the quality of decision-making on mode of birth after caesarean section. © 2013 Royal College of Obstetricians and Gynaecologists.

Integral tests of coupled multigroup neutron and gamma cross sections with fission and fusion sources

International Nuclear Information System (INIS)

Schriewer, J.; Hehn, G.; Mattes, M.; Pfister, G.; Keinert, J.

1978-01-01

Calculations were made for different benchmark experiments in order to test the coupled multigroup neutron and gamma library EURLIB-3 with 100 neutron groups and 20 gamma groups. In cooperation with EURATOM, Ispra, we produced this shielding library recently from ENDF/B-IV data for application in fission and fusion technology. Integral checks were performed for natural lithium, carbon, oxygen, and iron. Since iron is the most important structural material in nuclear technology, we started with calculations of iron benchmark experiments. Most of them are integral experiments of INR, Karlsruhe, but comparisons were also done with benchmark experiments from USA and Japan. For the experiments with fission sources we got satisfying results. All details of the resonances cannot be checked with flux measurements and multigroup cross sections used. But some averaged resonance behaviour of the measured and calculated fluxes can be compared and checked within the error limits given. We get greater differences in the calculations of benchmark experiments with 14 MeV neutron sources. For iron the group cross sections of EURLIB-3 produce an underestimation of the neutron flux in a broad energy region below the source energy. The conclusion is that the energy degradation by inelastic scattering is too strong. For fusion application the anisotropy of the inelastic scatter process must be taken into account, which isn't done by the processing codes at present. If this effect isn't enough, additional corrections have to be applied to the inelastic cross sections of iron in ENDF/B-IV. (author)

Self administered cognitive screening test (TYM) for detection of Alzheimer’s disease: cross sectional study

Science.gov (United States)

Pengas, George; Dawson, Kate; Clatworthy, Philip

2009-01-01

Objective To evaluate a cognitive test, the TYM (“test your memory”), in the detection of Alzheimer’s disease. Design Cross sectional study. Setting Outpatient departments in three hospitals, including a memory clinic. Participants 540 control participants aged 18-95 and 139 patients attending a memory clinic with dementia/amnestic mild cognitive impairment. Intervention Cognitive test designed to use minimal operator time and to be suitable for non-specialist use. Main outcome measures Performance of normal controls on the TYM. Performance of patients with Alzheimer’s disease on the TYM compared with age matched controls. Validation of the TYM with two standard tests (the mini-mental state examination (MMSE) and the Addenbrooke’s cognitive examination-revised (ACE-R)). Sensitivity and specificity of the TYM in the detection of Alzheimer’s disease. Results Control participants completed the TYM with an average score of 47/50. Patients with Alzheimer’s disease scored an average of 33/50. The TYM score shows excellent correlation with the two standard tests. A score of ≤42/50 had a sensitivity of 93% and specificity of 86% in the diagnosis of Alzheimer’s disease. The TYM was more sensitive in detection of Alzheimer’s disease than the mini-mental examination, detecting 93% of patients compared with 52% for the mini-mental state exxamination. The negative and positive predictive values of the TYM with the cut off of ≤42 were 99% and 42% with a prevalence of Alzheimer’s disease of 10%. Thirty one patients with non-Alzheimer dementias scored an average of 39/50. Conclusions The TYM can be completed quickly and accurately by normal controls. It is a powerful and valid screening test for the detection of Alzheimer’s disease. PMID:19509424

A microfluidic approach to water-rock interactions using thin rock sections: Pb and U sorption onto thin shale and granite sections

Energy Technology Data Exchange (ETDEWEB)

Oh, Youn Soo [Institute of Mine Reclamation Technology, Mine Reclamation Corp., 2 Segye-ro, Wonju-si, Gangwon-do, 26464 (Korea, Republic of); Jo, Ho Young, E-mail: hyjo@korea.ac.kr [Department of Earth and Environmental Sciences, Korea University, Anam-dong, Seongbuk-gu, Seoul, 02841 (Korea, Republic of); Ryu, Ji-Hun; Kim, Geon-Young [Korea Atomic Energy Research Institute, 1045 Daedeokdaero, Yuseong-gu, Daejeon, 34057 (Korea, Republic of)

2017-02-15

Highlights: • Microfluidic tests was used to investigate water-rock (mineral) interactions. • Pb and U sorption onto thin shale and granite sections was evaluated. • Pb removal by thin shale section is related primarily to Fe-containing minerals. • A slightly larger amount of U was removed onto the thin granite section with Fe-containing minerals. - Abstract: The feasibility of using microfluidic tests to investigate water-rock (mineral) interactions in fractures regarding sorption onto thin rock sections (i.e., shale and granite) of lead (Pb) and uranium (U) was evaluated using a synthetic PbCl{sub 2} solution and uranium-containing natural groundwater as fluids. Effluent composition and element distribution on the thin rock sections before and after microfluidic testing were analyzed. Most Pb removal (9.8 mg/cm{sup 2}) occurred within 3.5 h (140 PVF), which was 74% of the total Pb removal (13.2 mg/cm{sup 2}) at the end of testing (14.5 h, 560 PVF). Element composition on the thin shale sections determined by μ-XRF analysis indicated that Pb removal was related primarily to Fe-containing minerals (e.g., pyrite). Two thin granite sections (biotite rich, Bt-R and biotite poor, Bt-P) exhibited no marked difference in uranium removal capacity, but a slightly higher amount of uranium was removed onto the thin Bt-R section (266 μg/cm{sup 2}) than the thin Bt-P section (240 μg/cm{sup 2}) within 120 h (4800 PVF). However, uranium could not be detected by micro X-ray fluorescence (μ-XRF) analysis, likely due to the detection limit. These results suggest that microfluidic testing on thin rock sections enables quantitative evaluation of rock (mineral)-water interactions at the micro-fracture or pore scale.

HIV testing among men who have sex with men in Tijuana, Mexico: a cross-sectional study.

Science.gov (United States)

Pines, Heather A; Goodman-Meza, David; Pitpitan, Eileen V; Torres, Karla; Semple, Shirley J; Patterson, Thomas L

2016-02-04

HIV testing is critical to the delivery of comprehensive HIV prevention and care services, yet coverage of sexual minorities by HIV testing programmes remains insufficient in many low- and middle-income countries, including Mexico. The objective of this study was to identify the prevalence and correlates of HIV testing among men who have sex with men (MSM) in Tijuana, Mexico. We conducted a cross-sectional study (2012-2013) among 189 MSM recruited via respondent-driven sampling (RDS). RDS-weighted logistic regression was used to identify correlates of prior HIV testing. RDS-adjusted prevalence of prior and recent (≤ 12 months) HIV testing was 63.5% (95% CI 51.9% to 73.5%) and 36.8% (95% CI 25.4% to 46.4%), respectively. Prior HIV testing was positively associated with older age (adjusted OR (AOR)=1.09, 95% CI 1.04 to 1.15), being born in Tijuana (AOR=2.68, 95% CI 1.05 to 6.86), higher levels of education (AOR=2.65, 95% CI 1.08 to 6.53), identifying as homosexual or gay (AOR=3.73, 95% CI 1.48 to 9.42), being more 'out' about having sex with men (AOR=1.28, 95% CI:1.02 to 1.62), and a history of sexual abuse (AOR=3.24, 95% CI 1.06 to 9.86). Prior HIV testing was negatively associated with reporting more condomless anal intercourse acts (past 2 months) (AOR=0.95, 95% CI 0.92 to 0.98) and greater internalised homophobia (AOR=0.92, 95% CI 0.86 to 0.99). Our findings indicate an urgent need for expanded HIV testing services for MSM in Tijuana. Innovative, non-stigmatising, confidential HIV testing interventions targeted at young, less educated, migrant and non-gay identifying MSM may facilitate HIV testing and timely linkage to HIV care and treatment within this population. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

The effect of inlet flow oscillations on reflooding of a tubular test section

International Nuclear Information System (INIS)

Oh, S.; Banerjee, S.; Yadigaroglu, G.

1983-01-01

The reflooding of a vertical channel under oscillatory inlet flow conditions has been investigated experimentally. Compared to constant injection, oscillations always increase the liquid carryover in the early stages of reflooding. As reflooding progresses, the enhancement diminishes. The crossover point roughly coincides with saturation of the liquid at the quench front (QF). The higher liquid carryover at the beginning increases downstream heat transfer and speeds up QF propagation. But this higher liquid carryover, in turn, reduces the test section mass accumulation rate and delays QF propagation at later stages. The enhancement of liquid carryover, and the early increase and subsequent decrease in quench velocity are all accentuated as the oscillation amplitude and frequency increase. Large amplitude oscillations change the characteristics of QF propagation and the heat transfer immediately downstream of QF substantially. Correlations based on constant-injection reflooding data are not adequate, even if they are applied on an average local-conditions basis

Comparison between SRAM SEE cross-sections from ion beam testing with those obtained using a new picosecond pulsed laser facility

International Nuclear Information System (INIS)

Jones, R.; Chugg, A.M.; Jones, C.M.S.; Duncan, P.H.; Dyer, C.S.; Sanderson, C.

1999-01-01

A laser system has been designed to be capable of delivering large numbers of pulses across a micro-chip die under computer control, so as rapidly to generate upset and latch-up cross-section curves, in order to provide an efficient screening tool for SEE (single event effect) susceptibility. The system has been automated to make screening of parts for use in an SEE environment fast, efficient and inexpensive. A comparison between ion beam test results and laser test results has been used to develop initial calibrations between laser energy and LET (linear energy transfer)

Neutron integral test of graphite cross sections in MeV energy region for the JENDL-3T through an analysis of WINFRITH shielding experiment

International Nuclear Information System (INIS)

Ueki, Kohtaro; Sakurai, Kiyoshi.

1988-01-01

The neutron integral tests of graphite cross sections in MeV neutron energy region for the ENDF/B-IV, JENDL-2, JENDL-3PR1 and -3T were performed through the Monte Carlo analysis of the graphite shielding experiment at the WINFRITH. The measured values were on the reaction rates of 115 In(n,n') 115m In, 27 Al(n,α) 24 Na, 32 S(n,p) 32 P, and 103 Rh(n,n') 103m Rh threshold detectors located in the graphite slabs, so that the experiment on the graphite was good at the integral test of neutron cross sections in MeV energy resion. (author)

Secondary Electron Yield Measurements and Groove Chambers Tests in the PEP-II Beam Line Straights Sections

International Nuclear Information System (INIS)

Pivi, M

2008-01-01

Beam instability caused by the electron cloud has been observed in positron and proton storage rings and it is expected to be a limiting factor in the performance of the positron Damping Ring (DR) of future Linear Colliders such as ILC and CLIC [1, 2]. In the Positron Low Energy Ring (LER) of the PEP-II accelerator, we have installed vacuum chambers with rectangular grooves in a straight magnetic-free section to test this promising possible electron cloud mitigation technique. We have also installed a special chamber to monitor the secondary electron yield of TiN and TiZrV (NEG) coating, Copper, Stainless Steel and Aluminum under the effect of electron and photon conditioning in situ in the beam line. In this paper, we describe the ongoing R and D effort to mitigate the electron cloud effect for the ILC damping ring, the latest results on in situ secondary electron yield conditioning and recent update on the groove tests in PEP-II

Psychosocial determinants of HIV testing across stages of change in Spanish population: a cross-sectional national survey

Directory of Open Access Journals (Sweden)

Maria Jose Fuster-RuizdeApodaca

2017-03-01

Full Text Available Abstract Background The goal of this research is to study the psychosocial determinants of HIV-testing as a function of the decision or change stage concerning this health behavior. The determinants considered in the major ongoing health models and the stages contemplated in the Precaution Adoption Process Model are analysed. Methods A cross-sectional survey was administered to 1,554 people over 16 years of age living in Spain by a computer-assisted telephone interview (CATI. The sample design was randomised, with quotas of sex and age. The survey measured various psychosocial determinants of health behaviors considered in the main cognitive theories, the interviewees' stage of change concerning HIV-testing (lack of awareness, decision not to act, decision to act, action, maintenance, and abandonment, and the signal for the action of getting tested or the perceived barriers to being tested. Results Approximately two thirds of the population had not ever had the HIV test. The predominant stage was lack of awareness. The most frequently perceived barriers to testing were related to the health system and to the stigma. We also found that the psychosocial determinants studied differed depending on the respondents' stage of change. Perception of risk, perceived self-efficacy, proximity to people who had been tested, perceived benefits of knowing the diagnosis, and a positive instrumental and emotional attitude were positively associated with the decision and maintenance of testing behavior. However, unrealistic underestimation of the risk of HIV infection, stereotypes about the infection, and the perceived severity of HIV were associated with the decision not to be tested. Conclusions There are various sociocognitive and motivational profiles depending on people’s decision stage concerning HIV-testing. Knowing this profile may allow us to design interventions to influence the psychosocial determinants that characterise each stage of change.

Psychosocial determinants of HIV testing across stages of change in Spanish population: a cross-sectional national survey.

Science.gov (United States)

Fuster-RuizdeApodaca, Maria Jose; Laguia, Ana; Molero, Fernando; Toledo, Javier; Arrillaga, Arantxa; Jaen, Angeles

2017-03-07

The goal of this research is to study the psychosocial determinants of HIV-testing as a function of the decision or change stage concerning this health behavior. The determinants considered in the major ongoing health models and the stages contemplated in the Precaution Adoption Process Model are analysed. A cross-sectional survey was administered to 1,554 people over 16 years of age living in Spain by a computer-assisted telephone interview (CATI). The sample design was randomised, with quotas of sex and age. The survey measured various psychosocial determinants of health behaviors considered in the main cognitive theories, the interviewees' stage of change concerning HIV-testing (lack of awareness, decision not to act, decision to act, action, maintenance, and abandonment), and the signal for the action of getting tested or the perceived barriers to being tested. Approximately two thirds of the population had not ever had the HIV test. The predominant stage was lack of awareness. The most frequently perceived barriers to testing were related to the health system and to the stigma. We also found that the psychosocial determinants studied differed depending on the respondents' stage of change. Perception of risk, perceived self-efficacy, proximity to people who had been tested, perceived benefits of knowing the diagnosis, and a positive instrumental and emotional attitude were positively associated with the decision and maintenance of testing behavior. However, unrealistic underestimation of the risk of HIV infection, stereotypes about the infection, and the perceived severity of HIV were associated with the decision not to be tested. There are various sociocognitive and motivational profiles depending on people's decision stage concerning HIV-testing. Knowing this profile may allow us to design interventions to influence the psychosocial determinants that characterise each stage of change.

Laterality judgments in people with low back pain--A cross-sectional observational and test-retest reliability study.

Science.gov (United States)

Linder, Martin; Michaelson, Peter; Röijezon, Ulrik

2016-02-01

Disruption of cortical representation, or body schema, has been indicated as a factor in the persistence and recurrence of low back pain (LBP). This has been observed through impaired laterality judgment ability and it has been suggested that this ability is affected in a spatial rather than anatomical manner. We compared laterality judgment performance of foot and trunk movements between people with LBP with or without leg pain and healthy controls, and investigated associations between test performance and pain. We also assessed the test-retest reliability of the Recognise Online™ software when used in a clinical and a home setting. Cross-sectional observational and test-retest study. Thirty individuals with LBP and 30 healthy controls performed judgment tests of foot and trunk laterality once supervised in a clinic and twice at home. No statistically significant group differences were found. LBP intensity was negatively related to trunk laterality accuracy (p = 0.019). Intraclass correlation values ranged from 0.51 to 0.91. Reaction time improved significantly between test occasions while accuracy did not. Laterality judgments were not impaired in subjects with LBP compared to controls. Further research may clarify the relationship between pain mechanisms in LBP and laterality judgment ability. Reliability values were mostly acceptable, with wide and low confidence intervals, suggesting test-retest reliability for Recognise Online™ could be questioned in this trial. A significant learning effect was observed which should be considered in clinical and research application of the test. Copyright © 2015 Elsevier Ltd. All rights reserved.

Demonstration of the test-retest reliability and sensitivity of the Lower Limb Functional Index-10 as a measure of functional recovery post burn injury: a cross-sectional repeated measures study design.

Science.gov (United States)

Ryland, Margaret E; Grisbrook, Tiffany L; Wood, Fiona M; Phillips, Michael; Edgar, Dale W

2016-01-01

Lower limb burns can significantly delay recovery of function. Measuring lower limb functional outcomes is challenging in the unique burn patient population and necessitates the use of reliable and valid tools. The aims of this study were to examine the test-retest reliability, sensitivity, and internal consistency of Sections 1 and 3 of the Lower Limb Functional Index-10 (LLFI-10) questionnaire for measuring functional ability in patients with lower limb burns over time. Twenty-nine adult patients who had sustained a lower limb burn injury in the previous 12 months completed the test-retest procedure of the study. In addition, the minimal detectable change (MDC) was calculated for Section 1 and 3 of the LLFI-10. Section 1 is focused on the activity limitations experienced by patients with a lower limb disorder whereas Section 3 involves patients indicating their current percentage of pre-injury duties. Section 1 of the LLFI-10 demonstrated excellent test-retest reliability (intra-class correlation coefficient (ICC) 0.98, 95 % CI 0.96-0.99) whilst Section 3 demonstrated high test-retest reliability (ICC 0.88, 95 % CI 0.79-0.94). MDC scores for Sections 1 and 3 were 1.27 points and 30.22 %, respectively. Internal consistency was demonstrated with a significant negative association (r s  = -0.83) between Sections 1 and 3 of the LLFI-10 (p reliable for measuring functional ability in patients who have sustained lower limb burns in the previous 12 months, and furthermore, Section 1 is sensitive to changes in patient function over time.

Knowledge and perceptions of couples' voluntary counseling and testing in urban Rwanda and Zambia: a cross-sectional household survey.

Directory of Open Access Journals (Sweden)

April L Kelley

2011-05-01

Full Text Available Most incident HIV infections in sub-Saharan Africa occur between cohabiting, discordant, heterosexual couples. Though couples' voluntary HIV counseling and testing (CVCT is an effective, well-studied intervention in Africa, <1% of couples have been jointly tested.We conducted cross-sectional household surveys in Kigali, Rwanda (n = 600 and Lusaka, Zambia (n = 603 to ascertain knowledge, perceptions, and barriers to use of CVCT.Compared to Lusaka, Kigali respondents were significantly more aware of HIV testing sites (79% vs. 56%; had greater knowledge of HIV serodiscordance between couples (83% vs. 43%; believed CVCT is good (96% vs. 72%; and were willing to test jointly (91% vs. 47%. Stigma, fear of partner reaction, and distance/cost/logistics were CVCT barriers.Though most respondents had positive attitudes toward CVCT, the majority were unaware that serodiscordance between cohabiting couples is possible. Future messages should target gaps in knowledge about serodiscordance, provide logistical information about CVCT services, and aim to reduce stigma and fear.

FIZCON, ENDF/B Cross-Sections Redundancy Check

International Nuclear Information System (INIS)

Dunford, Charles L.

2007-01-01

1 - Description of program or function: FIZCON is a program for checking that an evaluated data file has valid data and conforms to recommended procedures. Version 7.01 (April 2005): set success flag after return from beginning; fixed valid level check for an isomer; fixed subsection energy range test in ckf9; changed lower limit on potential scattering test; fixed error in j-value test when l=0 and i=0; added one more significant figure to union grid check and sum up output messages; partial fission cross sections mt=19,20,21 and 38 did not require secondary energy distributions in file 5; corrected product test for elastic scattering; moved potential scattering test to psyche. Version 7.02 (May 2005): Fixed resonance parameter sum test. 2 - Method of solution: FIZCON can recognise the difference between ENDF-6 and ENDF-5 formats and performs its tests accordingly. Some of the tests performed include: data arrays are in increasing energy order; resonance parameter widths add up to the total; Q-values are reasonable and consistent; no required sections are missing and all cover the proper energy range; secondary distributions are normalized to 1.0; energy conservation in decay spectra. Optional tests can be performed to check the redundant cross sections, and algorithms can be used to check for possible incorrect entry of data values (Deviant Point test)

Overview of the computerized adaptive testing special section

Directory of Open Access Journals (Sweden)

Vicente Ponsoda

2000-01-01

Full Text Available Presentación de la sección monográfica sobre test adaptativos informatizados. Este artículo proporciona una visión conjunta de la sección especial de Psicológica sobre tests adaptativos informatizados. Se presenta también una breve introducción al tema. De cada artículo se muestran sus principales resultados, las conexiones con los demás trabajos de la sección especial y el tema de investigación con el que está más relacionado.

Differential Top Cross-section Measurements

CERN Document Server

Fenton, Michael James; The ATLAS collaboration

2017-01-01

The top quark is the heaviest known fundamental particle. The measurement of the differential top-quark pair production cross-section provides a stringent test of advanced perturbative QCD calculations. The ATLAS collaboration has performed detailed measurements of those differential cross sections at a centre-of-mass energy of 13 TeV. This talk focuses on differential cross-section measurements in the lepton+jets final state, including using boosted top quarks to probe our understanding of top quark production in the TeV regime.

Prototype Repository. Tracer dilution tests during operation phase, test campaign 3

Energy Technology Data Exchange (ETDEWEB)

Harrstroem, Johan; Andersson, Peter (Geosigma AB (Sweden))

2010-05-15

The Prototype Repository project is focused on testing and demonstrating the function of the SKB deep repository system. The third tracer dilution campaign during the Prototype Repository operation period was performed in January 2010. The purpose was to estimate the groundwater flows and hydraulic gradients in the boreholes vicinity and will function as a reference for comparison with results from modeling and prior assumptions. The test campaign consisted of tracer dilution tests in 13 different borehole sections. Each test consisted of approximately 15-55 min tracer injection time and about 1-3 days dilution test time depending on the transmissivity of the test section. The data interpretation also included estimates of the local hydraulic gradients in the vicinity of the borehole sections

Knowledge, attitudes and preferences regarding genetic testing for smoking cessation. A cross-sectional survey among Dutch smokers.

Science.gov (United States)

Quaak, Marieke; Smerecnik, Chris; van Schooten, Frederik J; de Vries, Hein; van Schayck, Constant P

2012-01-01

Objectives Recent research strongly suggests that genetic variation influences smokers' ability to stop. Therefore, the use of (pharmaco) genetic testing may increase cessation rates. This study aims to assess the intention of smokers concerning undergoing genetic testing for smoking cessation and their knowledge, attitudes and preferences about this subject. Design Online cross-sectional survey. Setting Database internet research company of which every inhabitant of the Netherlands of ≥12 years with an email address and capable of understanding Dutch can become a member. Participants 587 of 711 Dutch smokers aged ≥18 years, daily smokers for ≥5 years and smoke on average ≥10 cigarettes/day (response rate=83%). Primary and secondary outcome measures Smokers' knowledge, attitudes and preferences and their intention to undergo genetic testing for smoking cessation. Results Knowledge on the influence of genetic factors in smoking addiction and cessation was found to be low. Smokers underestimated their chances of having a genetic predisposition and the influence of this on smoking cessation. Participants perceived few disadvantages, some advantages and showed moderate self-efficacy towards undergoing a genetic test and dealing with the results. Smokers were mildly interested in receiving information and participating in genetic testing, especially when offered by their general practitioner (GP). Conclusions For successful implementation of genetic testing for smoking in general practice, several issues should be addressed, such as the knowledge on smoking cessation, genetics and genetic testing (including advantages and disadvantages) and the influence of genetics on smoking addiction and cessation. Furthermore, smokers allocate their GPs a crucial role in the provision of information and the delivery of a genetic test for smoking; however, it is unclear whether GPs will be able and willing to take on this role.

Knowledge, attitudes and preferences regarding genetic testing for smoking cessation. A cross-sectional survey among Dutch smokers

Science.gov (United States)

Smerecnik, Chris; van Schooten, Frederik J; de Vries, Hein; van Schayck, Constant P

2012-01-01

Objectives Recent research strongly suggests that genetic variation influences smokers' ability to stop. Therefore, the use of (pharmaco) genetic testing may increase cessation rates. This study aims to assess the intention of smokers concerning undergoing genetic testing for smoking cessation and their knowledge, attitudes and preferences about this subject. Design Online cross-sectional survey. Setting Database internet research company of which every inhabitant of the Netherlands of ≥12 years with an email address and capable of understanding Dutch can become a member. Participants 587 of 711 Dutch smokers aged ≥18 years, daily smokers for ≥5 years and smoke on average ≥10 cigarettes/day (response rate=83%). Primary and secondary outcome measures Smokers' knowledge, attitudes and preferences and their intention to undergo genetic testing for smoking cessation. Results Knowledge on the influence of genetic factors in smoking addiction and cessation was found to be low. Smokers underestimated their chances of having a genetic predisposition and the influence of this on smoking cessation. Participants perceived few disadvantages, some advantages and showed moderate self-efficacy towards undergoing a genetic test and dealing with the results. Smokers were mildly interested in receiving information and participating in genetic testing, especially when offered by their general practitioner (GP). Conclusions For successful implementation of genetic testing for smoking in general practice, several issues should be addressed, such as the knowledge on smoking cessation, genetics and genetic testing (including advantages and disadvantages) and the influence of genetics on smoking addiction and cessation. Furthermore, smokers allocate their GPs a crucial role in the provision of information and the delivery of a genetic test for smoking; however, it is unclear whether GPs will be able and willing to take on this role. PMID:22223839

Wall Correction Model for Wind Tunnels with Open Test Section

DEFF Research Database (Denmark)

Sørensen, Jens Nørkær; Shen, Wen Zhong; Mikkelsen, Robert Flemming

2004-01-01

, the corrections from the model are in very good agreement with the CFD computaions, demonstrating that one-dimensional momentum theory is a reliable way of predicting corrections for wall interference in wind tunnels with closed as well as open cross sections. Keywords: Wind tunnel correction, momentum theory...

Choreographer Pre-Testing Code Analysis and Operational Testing.

Energy Technology Data Exchange (ETDEWEB)

Fritz, David J. [Sandia National Laboratories (SNL-CA), Livermore, CA (United States); Harrison, Christopher B. [Sandia National Laboratories (SNL-CA), Livermore, CA (United States); Perr, C. W. [Sandia National Laboratories (SNL-CA), Livermore, CA (United States); Hurd, Steven A [Sandia National Laboratories (SNL-CA), Livermore, CA (United States)

2014-07-01

Choreographer is a "moving target defense system", designed to protect against attacks aimed at IP addresses without corresponding domain name system (DNS) lookups. It coordinates actions between a DNS server and a Network Address Translation (NAT) device to regularly change which publicly available IP addresses' traffic will be routed to the protected device versus routed to a honeypot. More details about how Choreographer operates can be found in Section 2: Introducing Choreographer. Operational considerations for the successful deployment of Choreographer can be found in Section 3. The Testing & Evaluation (T&E) for Choreographer involved 3 phases: Pre-testing, Code Analysis, and Operational Testing. Pre-testing, described in Section 4, involved installing and configuring an instance of Choreographer and verifying it would operate as expected for a simple use case. Our findings were that it was simple and straightforward to prepare a system for a Choreographer installation as well as configure Choreographer to work in a representative environment. Code Analysis, described in Section 5, consisted of running a static code analyzer (HP Fortify) and conducting dynamic analysis tests using the Valgrind instrumentation framework. Choreographer performed well, such that only a few errors that might possibly be problematic in a given operating situation were identified. Operational Testing, described in Section 6, involved operating Choreographer in a representative environment created through Emulytics^TM . Depending upon the amount of server resources dedicated to Choreographer vis-á-vis the amount of client traffic handled, Choreographer had varying degrees of operational success. In an environment with a poorly resourced Choreographer server and as few as 50-100 clients, Choreographer failed to properly route traffic over half the time. Yet, with a well-resourced server, Choreographer handled over 1000 clients without missrouting. Choreographer

Development of C-band Accelerating Section for SuperKEKB

CERN Document Server

Kamitani, T; Ikeda, M; Kakihara, K; Ohsawa, S; Oogoe, T; Sugimura, T; Takatomi, T; Yamaguchi, S; Yokoyama, K

2004-01-01

For the luminosity upgrade of the present KEK B-factory to SuperKEKB, the injector linac has to increase the positron acceleration energy from 3.5 to 8.0 GeV. In order to double the acceleration field gradient from 21 to 42 MV/m, design studies on C-band accelerator module has started in 2002. First prototype 1-m long accelerating section has been fabricated based upon a design which is half scale of the present S-band section. High power test of the C-band section has been performed at a test stand and later at an accelerator module in the KEKB injector linac. In a beam acceleration test, a field gradient of 41 MV/m is achieved with 43 MW RF power from a klystron. This paper report on the recent status of the high-power test and also the development of a second prototype section.

Factors affecting voluntary HIV counselling and testing among men in Ethiopia: a cross-sectional survey

Directory of Open Access Journals (Sweden)

Leta Tesfaye H

2012-06-01

Full Text Available Abstract Background Voluntary HIV counselling and testing (VCT is one of the key strategies in the HIV/AIDS prevention and control programmes in Ethiopia. However, utilization of this service among adults is very low. The aim of the present study was to investigate factors associated with VCT utilization among adult men since men are less likely than women to be offered and accept routine HIV testing. Methods The study utilized data from the Ethiopian Demographic Health Survey (EDHS 2005, which is a cross-sectional survey conducted on a nationally representative sample. Using cluster sampling, 6,778 men aged 15–59 years were selected from all the eleven administrative regions in Ethiopia. Logistic regression was used to analyze potential factors associated with VCT utilization. Results Overall, 21.9% of urban men and 2.6% of rural men had ever tested for HIV through VCT and most of them had learned their HIV test result. Having no stigmatizing attitudes toward people living with HIV/AIDS was found to be strongly and positively associated with VCT utilization in both urban and rural strata. In rural areas HIV test rates were higher among younger men (aged ≤44 years and those of higher socio-economic position (SEP. Among urban men, risky sexual behaviour was positively associated with VCT utilization whereas being Muslim was found to be inversely associated with utilization of VCT. Area of residence as well as SEP strongly affected men’s level of stigmatizing attitudes toward people living with HIV/AIDS. Conclusions VCT utilization among men in Ethiopia was low and affected by HIV/AIDS-related stigma and residence. In order to increase VCT acceptability, HIV/AIDS prevention and control programs in the country should focus on reducing HIV/AIDS-related stigma. Targeting rural men with low SEP should be given first priority when designing, expanding, and implementing VCT services in the country.

Developing Scientific Reasoning Through Drawing Cross-Sections

Science.gov (United States)

Hannula, K. A.

2012-12-01

Cross-sections and 3D models of subsurface geology are typically based on incomplete information (whether surface geologic mapping, well logs, or geophysical data). Creating and evaluating those models requires spatial and quantitative thinking skills (including penetrative thinking, understanding of horizontality, mental rotation and animation, and scaling). However, evaluating the reasonableness of a cross-section or 3D structural model also requires consideration of multiple possible geometries and geologic histories. Teaching students to create good models requires application of the scientific methods of the geosciences (such as evaluation of multiple hypotheses and combining evidence from multiple techniques). Teaching these critical thinking skills, especially combined with teaching spatial thinking skills, is challenging. My Structural Geology and Advanced Structural Geology courses have taken two different approaches to developing both the abilities to visualize and to test multiple models. In the final project in Structural Geology (a 3rd year course with a pre-requisite sophomore mapping course), students create a viable cross-section across part of the Wyoming thrust belt by hand, based on a published 1:62,500 geologic map. The cross-section must meet a number of geometric criteria (such as the template constraint), but is not required to balance. Each student tries many potential geometries while trying to find a viable solution. In most cases, the students don't visualize the implications of the geometries that they try, but have to draw them and then erase their work if it does not meet the criteria for validity. The Advanced Structural Geology course used Midland Valley's Move suite to test the cross-sections that they made in Structural Geology, mostly using the flexural slip unfolding algorithm and testing whether the resulting line lengths balanced. In both exercises, students seemed more confident in the quality of their cross-sections when the

Statistical test of reproducibility and operator variance in thin-section modal analysis of textures and phenocrysts in the Topopah Spring member, drill hole USW VH-2, Crater Flat, Nye County, Nevada

International Nuclear Information System (INIS)

Moore, L.M.; Byers, F.M. Jr.; Broxton, D.E.

1989-06-01

A thin-section operator-variance test was given to the 2 junior authors, petrographers, by the senior author, a statistician, using 16 thin sections cut from core plugs drilled by the US Geological Survey from drill hole USW VH-2 standard (HCQ) drill core. The thin sections are samples of Topopah Spring devitrified rhyolite tuff from four textural zones, in ascending order: (1) lower nonlithophysal, (2) lower lithopysal, (3) middle nonlithophysal, and (4) upper lithophysal. Drill hole USW-VH-2 is near the center of the Crater Flat, about 6 miles WSW of the Yucca Mountain in Exploration Block. The original thin-section labels were opaqued out with removable enamel and renumbered with alpha-numeric labels. The sliders were then given to the petrographer operators for quantitative thin-section modal (point-count) analysis of cryptocrystalline, spherulitic, granophyric, and void textures, as well as phenocryst minerals. Between operator variance was tested by giving the two petrographers the same slide, and within-operator variance was tested by the same operator the same slide to count in a second test set, administered at least three months after the first set. Both operators were unaware that they were receiving the same slide to recount. 14 figs., 6 tabs

Coal Ash Corrosion Resistant Materials Testing

Energy Technology Data Exchange (ETDEWEB)

D. K. McDonald; P. L. Daniel; D. J. DeVault

2007-12-31

In April 1999, three identical superheater test sections were installed into the Niles Unit No.1 for the purpose of testing and ranking the coal ash corrosion resistance of candidate superheater alloys. The Niles boiler burns high sulfur coal (3% to 3.5%) that has a moderate alkali content (0.2% sodium equivalents), thus the constituents necessary for coal ash corrosion are present in the ash. The test sections were controlled to operate with an average surface metal temperature from approximately 1060 F to 1210 F which was within the temperature range over which coal ash corrosion occurs. Thus, this combination of aggressive environment and high temperature was appropriate for testing the performance of candidate corrosion-resistant tube materials. Analyses of the deposit and scale confirmed that aggressive alkali sulfate constituents were present at the metal surface and active in tube metal wastage. The test sections were constructed so that the response of twelve different candidate tube and/or coating materials could be studied. The plan was to remove and evaluate one of the three test sections at time intervals of 1 year, 3 years, and 5 years. This would permit an assessment of performance of the candidate materials as a function of time. Test Section A was removed in November 2001 after about 24 months of service at the desired steam temperature set point, with about 15.5 months of exposure at full temperature. A progress report, issued in October 2002, was written to document the performance of the candidate alloys in that test section. The evaluation described the condition of each tube sample after exposure. It involved a determination of the rate of wall thickness loss for these samples. In cases where there was more than one sample of a candidate material in the test section, an assessment was made of the performance of the alloy as a function of temperature. Test Sections B and C were examined during the November 2001 outage, and it was decided that

cmpXLatt: Westinghouse automated testing tool for nodal cross section models

International Nuclear Information System (INIS)

Guimaraes, Petri Forslund; Rönnberg, Kristian

2011-01-01

The procedure for evaluating the merits of different nodal cross section representation models is normally both cumbersome and time consuming, and includes many manual steps when preparing appropriate benchmark problems. Therefore, a computer tool called cmpXLatt has been developed at Westinghouse in order to facilitate the process of performing comparisons between nodal diffusion theory results and corresponding transport theory results on a single node basis. Due to the large number of state points that can be evaluated by cmpXLatt, a systematic and comprehensive way of performing verification and validation of nodal cross section models is provided. This paper presents the main features of cmpXLatt and demonstrates the benefits of using cmpXLatt in a real life application. (author)

Experimental investigation of cooling by top spray and bottom flooding of a simulated 64 rod bundle for a BWR. Pt. 2. Main experiment with modified test section

International Nuclear Information System (INIS)

Nilsson, L.; Gustafson, L.; Harju, R.

1978-06-01

The cooling of an electrically heated, full scale 64-rod bundle has been investigated under simulated emergency core cooling conditions. Emphasis was laid on measurements of rod cladding and canister temperatures. By means of difference pressure measurements the levels in bundle, by-pass and downcomer could be estimated and thus the effective reflooding velocity. The test section was modified compared to the pre-tests, in order to improve system effects simulation. A new rod bundle was installed including a hollow, water, rod and 63 indirectly heated rods. Parameter effects of coolant mass flow rate and distribution, initial cladding temperature, pressure and power were studied. The effect of the way the test section was vented was also investigated and turned out to be very significant. (author)

Prevalence of prior HIV testing and associated factors among MSM in Zhejiang Province, China: a cross-sectional study

Directory of Open Access Journals (Sweden)

Runhua Li

2016-11-01

Full Text Available Abstract Background Men who have sex with men (MSM have become one of high-risk population for human immunodeficiency virus (HIV infection, due to their multiple sex partners and unprotected anal intercourse. Promoting HIV testing is an effective strategy for the prevention and control of HIV infection. We assessed the factors associated with a prior HIV testing history, which could provide guidance for implementation of future HIV intervention programs. Methods A cross-sectional study was conducted in three cities of Zhejiang Province, namely, Hangzhou, Ningbo and Wenzhou, using respondent-driven sampling, between December 2013 and June 2014. A face-to-face questionnaire survey was employed to collect relevant information about HIV testing. Univariate and multivariate logistic regression analyses were used to identify the factors associated with a prior HIV testing history. Results The adjusted rate of prior HIV testing among MSM in Zhejiang Province was 55.9 %. The adjusted rates of HIV and syphilis infections among MSM in Zhejiang Province were 14.0 % and 11.4 %, respectively. A weighted multivariate analysis showed that MSM of older age were more likely to be tested, as were MSM with higher level of education, self-reported homosexuality and a higher frequency of receiving AIDS/sexually transmitted infections educational intervention in the past year. MSM with suicidal inclination and self-perceived lower possibility of HIV infection were less likely to report ever having undergone an HIV test. Conclusions The prevalence of prior HIV testing among MSM in Zhejiang Province, China is low. Effective and more frequent interventional measures should be adopted to improve risk awareness and psychosocial support for younger, less educated MSM, and to encourage more MSM to undergo HIV testing.

A pilot application of the RELAP file to the steady state and transient analysis of a test section inside the BR2 reactor

International Nuclear Information System (INIS)

Ferri, M. G.; D'Auria, F.; Forasassi, G.; Giot, M.

2000-01-01

BR2 is a material test reactor sited in the Belgian Nuclear Research Centre in Mol. The main research programs carried out in BR2 are related to the safety of nuclear reactor structural materials and fuels, in normal and accidental conditions, plant lifetime evaluation and ageing of components. In this framework, a computer program that allows the performance of detailed, steady state analysis of several kinds of in-pile sections with an axisymmetrical geometry has been developed. Furthermore, comparing its results with those of the well known, extensively used, Relap5/Mod 3.2 code on a test problem has validated this program. This was performed in three steps: 1. modalisation development of a subsystem of a typical in-pile section. 2. steady state analysis and comparison with the above-mentioned program. 3. transient simulation of the same system; the considered transient consists of a loss of coolant flow. (author)

NASA Hybrid Wing Aircraft Aeroacoustic Test Documentation Report

Science.gov (United States)

Heath, Stephanie L.; Brooks, Thomas F.; Hutcheson, Florence V.; Doty, Michael J.; Bahr, Christopher J.; Hoad, Danny; Becker, Lawrence; Humphreys, William M.; Burley, Casey L.; Stead, Dan;

Commissioning of the STAR test section for experimental simulation of loss of coolant accident using the EC-208 instrumented fuel assembly of the IEA-R1 reactor

Energy Technology Data Exchange (ETDEWEB)

Maprelian, Eduardo; Torres, Walmir M.; Prado, Adelk C.; Umbehaun, Pedro E.; Franca, Renato L.; Santos, Samuel C.; Macedo, Luiz A.; Sabundjian, Gaiane, E-mail: emaprel@ipen.br, E-mail: wmtorres@ipen.br, E-mail: acprado@ipen.br, E-mail: umbehaun@ipen.br, E-mail: rlfranca@ipen.br, E-mail: samuelcs@ipen.br, E-mail: lamacedo@ipen.br, E-mail: gdjian@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SO (Brazil)

2015-07-01

The three basic safety functions of Research Reactors (RR) are the safe shutdown of the reactor, the proper cooling of the decay heat of the fuel elements and the confinement of radioactive materials. Compared to Nuclear Power Reactors, RR power release is small, yet its three safety functions must be met to ensure the integrity of the reactor. During a loss of coolant accident (LOCA) in pool type RR, partial or complete loss of pool water may occur, with consequent partial or complete uncovering of the fuel assemblies. In such an accident, the decay heat removal safety function must not be compromised. The Test Section for Experimental Simulation of Loss of Coolant Accident (STAR) is in commissioning phase. This test section will provide experimental data on partial and total uncovering of the EC-208 instrumented fuel assembly (IFA) irradiated in the IEA-R1. Experimental results will be useful in validation of computer codes for RR safety analysis, particularly on heat removal efficiency aspects (safety function) in accident conditions. STAR comprises a base on which is installed the IFA, the cylindrical stainless steel hull, the compressed air system for the test section emptying and refilling, and the instrumentation for temperature and level measurements. The commissioning tests or pre-operational check, consist of several preliminary tests to verify experimental procedures, the difficulties during assembling of STAR in the pool, the difficulties in control the emptying and refilling velocities, as well as, the repeatability capacity, tests of equipment, valves and systems and tests of instrumentation and data acquisition system. Safety, accuracy and easiness of operation will be checked. (author)

Measurement of the cross-section of electron-positron scattering at high energy and quantum electrodynamics testing

International Nuclear Information System (INIS)

Lalanne, D.

1970-01-01

The experiment we have performed on the ACO (Orsay Collider Ring) is one of the most accurate tests of quantum electrodynamics over very short interaction distances (10 -14 cm). We have studied the electron-positron elastic scattering at very wide angle. This work is divided into 4 parts. The first part reviews recent tests of quantum electrodynamics and presents the electron-positron elastic scattering. The second part describes the measurement of brightness: the experimental device, data analysis and accuracy. The measurement of brightness has been performed by detecting the photons emitted in the double Bremsstrahlung reaction: e + e - → e + e - γγ. The third part deals with the measurement of the number of Bhabha events. The last part compares the experimental value of the Bhabha scattering with the theoretically expected value. We have got the following results: the number of Bhabha events: 757 events, the experimental value for Bhabha scattering cross-section: [1.97 ± 0.09 (stat.) ± 0.10 (syst.)]*10 -31 cm 2 . The comparison of this experimental value with the expected value has allowed us to set the lower limit of the cutting parameter Λ: Λ > 2 GeV

Structural fatigue test results for large wind turbine blade sections

Science.gov (United States)

Faddoul, J. R.; Sullivan, T. L.

1982-01-01

In order to provide quantitative information on the operating life capabilities of wind turbine rotor blade concepts for root-end load transfer, a series of cantilever beam fatigue tests was conducted. Fatigue tests were conducted on a laminated wood blade with bonded steel studs, a low cost steel spar (utility pole) with a welded flange, a utility pole with additional root-end thickness provided by a swaged collar, fiberglass spars with both bonded and nonbonded fittings, and, finally, an aluminum blade with a bolted steel fitting (Lockheed Mod-0 blade). Photographs, data, and conclusions for each of these tests are presented. In addition, the aluminum blade test results are compared to field failure information; these results provide evidence that the cantilever beam type of fatigue test is a satisfactory method for obtaining qualitative data on blade life expectancy and for identifying structurally underdesigned areas (hot spots).

Integral test of neutron cross section data for future reactor materials through measurement and analysis of neutron spectra

International Nuclear Information System (INIS)

Mori, Takamasa

1985-05-01

In order to assess the cross section data for future reactor materials, such as molybdenum, niobium, titanium, lithium and fluorine, the angular neutron spectra in test piles of these materials or their chemical compounds have been measured in the energy range from a few keV to a few MeV by the linac time-of-flight method. The results have been compared with those theoretically calculated from the evaluated cross section data in such as JENDL-2 (or JENDL-1, JENDL-3PR1) and ENDF/B-IV. For both of molybdenum and niobium, it has been found that the energy distribution of inelastically scattered neutrons plays an important role in the analysis, and the JENDL library gives better predictions of spectrum shapes than ENDF/B-IV for both cases. In the case of niobium, however, it appears that the values of inelastic scattering cross section in JENDL-2 are too small around 2 MeV. It has been also found for niobium that the cross section data below 100 keV in ENDF/B-IV are inadequate. In a titanium pile, a discrepancy between the measured spectrum and the calculated one from ENDF/B-IV has been found in the energy range from about 60 keV to a few 100 keV. In order to investigate the cause of this discrepancy, the total cross sections for titanium have been measured by the transmission method. In the case of lithium, the discrepancy between the measured and calculated spectra is considerably reduced by adopting the angular distribution for 7 Li from ENDF/B-IV above about 500 keV. In the case of fluorine, spatial distributions of neutrons and X-rays have been also measured in both piles by the activation method to estimate the influence of photoneutrons generated in the sample material on the neutron distribution, and it has been found that their influence below 1 MeV is not so large as is necessary to be taken into account for the present assessment. (J.P.N)

Rank-based testing of equal survivorship based on cross-sectional survival data with or without prospective follow-up.

Science.gov (United States)

Chan, Kwun Chuen Gary; Qin, Jing

2015-10-01

Existing linear rank statistics cannot be applied to cross-sectional survival data without follow-up since all subjects are essentially censored. However, partial survival information are available from backward recurrence times and are frequently collected from health surveys without prospective follow-up. Under length-biased sampling, a class of linear rank statistics is proposed based only on backward recurrence times without any prospective follow-up. When follow-up data are available, the proposed rank statistic and a conventional rank statistic that utilizes follow-up information from the same sample are shown to be asymptotically independent. We discuss four ways to combine these two statistics when follow-up is present. Simulations show that all combined statistics have substantially improved power compared with conventional rank statistics, and a Mantel-Haenszel test performed the best among the proposal statistics. The method is applied to a cross-sectional health survey without follow-up and a study of Alzheimer's disease with prospective follow-up. © The Author 2015. Published by Oxford University Press. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Augmented cross-sectional studies with abbreviated follow-up for estimating HIV incidence.

Science.gov (United States)

Claggett, B; Lagakos, S W; Wang, R

2012-03-01

Cross-sectional HIV incidence estimation based on a sensitive and less-sensitive test offers great advantages over the traditional cohort study. However, its use has been limited due to concerns about the false negative rate of the less-sensitive test, reflecting the phenomenon that some subjects may remain negative permanently on the less-sensitive test. Wang and Lagakos (2010, Biometrics 66, 864-874) propose an augmented cross-sectional design that provides one way to estimate the size of the infected population who remain negative permanently and subsequently incorporate this information in the cross-sectional incidence estimator. In an augmented cross-sectional study, subjects who test negative on the less-sensitive test in the cross-sectional survey are followed forward for transition into the nonrecent state, at which time they would test positive on the less-sensitive test. However, considerable uncertainty exists regarding the appropriate length of follow-up and the size of the infected population who remain nonreactive permanently to the less-sensitive test. In this article, we assess the impact of varying follow-up time on the resulting incidence estimators from an augmented cross-sectional study, evaluate the robustness of cross-sectional estimators to assumptions about the existence and the size of the subpopulation who will remain negative permanently, and propose a new estimator based on abbreviated follow-up time (AF). Compared to the original estimator from an augmented cross-sectional study, the AF estimator allows shorter follow-up time and does not require estimation of the mean window period, defined as the average time between detectability of HIV infection with the sensitive and less-sensitive tests. It is shown to perform well in a wide range of settings. We discuss when the AF estimator would be expected to perform well and offer design considerations for an augmented cross-sectional study with abbreviated follow-up. © 2011, The

Comparison of constant-rate pumping test and slug interference test results at the Hanford Site B pond multilevel test facility

International Nuclear Information System (INIS)

Spane, F.A. Jr.; Thorne, P.D.

1995-10-01

Pacific Northwest Laboratory (PNL), as part of the Hanford Site Ground-Water Surveillance Project, is responsible for monitoring the movement and fate of contamination within the unconfined aquifer to ensure that public health and the environment are protected. To support the monitoring and assessment of contamination migration on the Hanford Site, a sitewide 3-dimensional groundwater flow model is being developed. Providing quantitative hydrologic property data is instrumental in development of the 3-dimensional model. Multilevel monitoring facilities have been installed to provide detailed, vertically distributed hydrologic characterization information for the Hanford Site unconfined aquifer. In previous reports, vertically distributed water-level and hydrochemical data obtained over time from these multi-level monitoring facilities have been evaluated and reported. This report describes the B pond facility in Section 2.0. It also provides analysis results for a constant-rate pumping test (Section 3.0) and slug interference test (Section 4.0) that were conducted at a multilevel test facility located near B Pond (see Figure 1. 1) in the central part of the Hanford Site. A hydraulic test summary (Section 5.0) that focuses on the comparison of hydraulic property estimates obtained using the two test methods is also presented. Reference materials are listed in Section 6.0

Effect of foot placements during sit to stand transition on timed up and go test in stroke subjects: A cross sectional study.

Science.gov (United States)

Joshua, Abraham M; Karnad, Shreekanth D; Nayak, Akshatha; Suresh, B V; Mithra, Prasanna; Unnikrishnan, B

2017-01-01

Timed up and go (TUG) test is been used as a screening tool for the assessment of risk of falling in individuals following stroke. Though TUG test is a quick test, it has fair sensitivity compared to other tests. This study was carried out to obtain and compare test scores for different types of foot placements during sit to stand transition in stroke subjects. A Cross-sectional study with purposive sampling included 28 post stroke subjects who were able to walk 6 meter with or without assistance. Timed Up and Go test was carried out with four different types of foot placements and scores were recorded. The data were compared using Kruskal-Wallis One way analysis of variance and Wilcoxon signed ranks test. There were comparable differences between asymmetric 1 test strategy which involved affected extremity to be placed behind the unaffected and other test strategies (Z = -4.457,-3.848,-4.458; p = 0.000). The initial foot placements during sit to stand transition influenced the time taken to complete the test which was significantly higher in asymmetric 1 strategy, Incorporation of the initial foot placement mainly asymmetric 1 strategy into conventional TUG test would help in identifying accurately the subject's functional mobility and postural stability.

Factors associated with continuing emergence of β-thalassemia major despite prenatal testing: a cross-sectional survey

Directory of Open Access Journals (Sweden)

Al Sabbah H

2017-09-01

Full Text Available Haleama Al Sabbah,1 Sarah Khan,1 Abdallah Hamadna,2 Lamia Abu Ghazaleh,2 Anwar Dudin,2 Bashar Adnan Karmi3 1College of Natural and Health Sciences, Zayed University, Dubai, UAE; 2Faculty of Medicine, An-Najah National University, Nablus, Palestine; 3Thalassemia Patients’ Friends Society, Ramallah, Palestine Purpose: Health care initiatives focusing on prenatal testing and premarital genetic screening aiming to reduce the incidence of β-thalassemia have emerged during the last decade. In Palestine, 4% of the population are known thalassemia carriers with new cases continuing to appear despite the availability of prenatal testing. This study aims to identify factors that influence the decision to retain or abort fetuses affected by β-thalassemia in Palestine. Methods: Convenience sampling was used to select 32 women (72 fetuses who were at risk of having a baby with β-thalassemia. A questionnaire on prenatal testing, test results, pregnancy outcomes, and factors influencing the decision to terminate the pregnancy were used for this cross-sectional study. The data were analyzed using SPSS version 17. Results: Among the fetuses screened, 36 (50% were thalassemia carriers and 20 (28% had β-thalassemia; 17 (85% affected fetuses were aborted. Religious beliefs were the most cited reason for opposing abortion while prior experience with β-thalassemia patients and awareness programs promoted abortions. Mothers who opted to retain an affected fetus had modest educational attainment. Higher educational level was significantly associated with the decision to abort an affected fetus (p<0.05. Conclusion: A religious consensus is needed on the abortion of fetuses affected by β-thalassemia. Improving female education and increasing awareness on thalassemia could help reduce the incidence of β-thalassemia in Palestine and around the world. Keywords: abortion, Islam, fetus, awareness

Design heating test section HeaTiNG-02

International Nuclear Information System (INIS)

Riswan Djambiar; Sagino; Dedy Haryanto; Joko Prasetio Witoko

2013-01-01

HeaTiNG-02 is a component test loop BETA which serves as a heater in conducting experimental heat transfer processes in two-phase flow in narrow slit-shaped plate, considering this phenomenon is one of the conditions postulated accident scenarios a NPP type PWR. To produce heat for the heating component takes the AC power the source voltage can be set from 0 Volts to 220 Volts with no more than a maximum power of 25 KVA. To obtain the thermal conditions on HeaTiNG-02 heating wire dimensions need to be determined and the corresponding voltage so that it will an expected power. Determination of the dimensions of the heater wire through calculations using electricity formulations. Retrieved draft heater test BETA (UUB) HeaTiNG-02 use material super kanthal (FeCuAl) in diameter (Ø) = 2 mm and wire length 3770 mm. Voltage regulators with a maximum power of 25 kVA with a minimum voltage of 0 volts and a maximum of 220 volts. Heater is used as the base to form refractory stone trench. (author)

Ice-condenser aerosol tests

International Nuclear Information System (INIS)

Ligotke, M.W.; Eschbach, E.J.; Winegardner, W.K.

1991-09-01

This report presents the results of an experimental investigation of aerosol particle transport and capture using a full-scale height and reduced-scale cross section test facility based on the design of the ice compartment of a pressurized water reactor (PWR) ice-condenser containment system. Results of 38 tests included thermal-hydraulic as well as aerosol particle data. Particle retention in the test section was greatly influenced by thermal-hydraulic and aerosol test parameters. Test-average decontamination factor (DF) ranged between 1.0 and 36 (retentions between ∼0 and 97.2%). The measured test-average particle retentions for tests without and with ice and steam ranged between DF = 1.0 and 2.2 and DF = 2.4 and 36, respectively. In order to apparent importance, parameters that caused particle retention in the test section in the presence of ice were steam mole fraction (SMF), noncondensible gas flow rate (residence time), particle solubility, and inlet particle size. Ice-basket section noncondensible flows greater than 0.1 m 3 /s resulted in stable thermal stratification whereas flows less than 0.1 m 3 /s resulted in thermal behavior termed meandering with frequent temperature crossovers between flow channels. 10 refs., 66 figs., 16 tabs

Operational test report for LERF Basin 242AL-44 integrity test

International Nuclear Information System (INIS)

Galioto, T.M.

1994-01-01

This operational test report documents the results of LERF operational testing per operational test procedure (OTP) TFPE-WP-0231, ''LERF Basin Integrity Testing.'' The primary purpose of the OTP was to resolve test exceptions generated as a result of TFPE-WP-0184. The TOP was prepared and performed in accordance with WHC-SD-534-OTP-002, ''Operational Test Plan for the 242-A Evaporator Upgrades and the Liquid Effluent Retention Facility.'' WHC-S-086, ''Specification for Operational Testing of the Liquid Effluent Retention Facility, Basin Integrity Testing,'' identified the test requirements and acceptance criteria. The completed, signed-off test procedure is contained in Appendix A. The test log is contained in Appendix B. Section 2.1 describes all the test exceptions written during performance of the Operational Test Procedure. The test revisions generated during the testing are discussed in Section 2.2. The dispositioned test exception forms are contained in Appendix C

Wall correction model for wind tunnels with open test section

DEFF Research Database (Denmark)

Sørensen, Jens Nørkær; Shen, Wen Zhong; Mikkelsen, Robert Flemming

2006-01-01

In the paper we present a correction model for wall interference on rotors of wind turbines or propellers in wind tunnels. The model, which is based on a one-dimensional momentum approach, is validated against results from CFD computations using a generalized actuator disc principle. In the model...... good agreement with the CFD computations, demonstrating that one-dimensional momentum theory is a reliable way of predicting corrections for wall interference in wind tunnels with closed as well as open cross sections....

The diagnostic performance evaluation of the SD BIOLINE HIV/syphilis Duo rapid test in southern Ethiopia: a cross-sectional study.

Science.gov (United States)

Shimelis, Techalew; Tadesse, Endale

2015-04-23

To determine the diagnostic performance of the SD BIOLINE HIV/syphilis Duo rapid test. A hospital-based cross-sectional study. This evaluation was conducted at one of the largest hospitals in southern Ethiopia. Serum samples obtained from clients attending the antiretroviral therapy and voluntary counselling and testing centres were used. Sera were originally collected for the purpose of investigating syphilis epidemiology. The performance of the test to detect HIV was evaluated using 400 sera (200 HIV positives and 200 HIV negatives). Also, its performance to detect syphilis was evaluated using 85 syphilis positive and 100 syphilis negative serum samples. Individuals tiebreaker to determine the result. We also used ELISA to resolve discordant HIV results. Syphilis serostatus was determined using the Treponema pallidum haemagglutination assay (TPHA). The respective sensitivity, specificity, positive predictive value and negative predictive value of the SD BIOLINE HIV/syphilis Duo test were 100, 99.5, 99.5 and 100% for HIV and 97.6, 96, 95.4 and 98% for syphilis testing, respectively. In reference to TPHA, the test kit reported 4 false positives and 2 false negative results for syphilis. The κ values were 0.99 for HIV testing and 0.94 for syphilis testing. The excellent performance of the SD BIOLINE HIV/syphilis Duo test to detect HIV as well as syphilis facilitates the integration of syphilis testing and treatment to the already established HIV prevention programme, ultimately contributing to the dual HIV and syphilis elimination goal. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

A cross-sectional survey of attitudes to HIV risk and rapid HIV testing among clients of sex workers in Switzerland.

Science.gov (United States)

Darling, Katharine E A; Diserens, Esther-Amélie; N'garambe, Chantal; Ansermet-Pagot, Anne; Masserey, Eric; Cavassini, Matthias; Bodenmann, Patrick

2012-10-01

To assess attitudes to HIV risk and acceptability of rapid HIV testing among clients of street-based female sex workers (FSW) in Lausanne, Switzerland, where HIV prevalence in the general population is 0.4%. The authors conducted a cross-sectional study in the red light district of Lausanne for five nights in September of 2008, 2009 and 2010. Clients of FSW were invited to complete a questionnaire in the street assessing demographic characteristics, attitudes to HIV risk and HIV testing history. All clients interviewed were then offered anonymous finger stick rapid HIV testing in a van parked on-site. The authors interviewed 112, 127 and 79 clients in 2008, 2009 and 2010, respectively. All were men, average age 32-37 years old; 40-60% were in a stable relationship. History of unprotected sex was higher with non-commercial partners (33-50%) than with FSW (6-11%); 29-46% of clients had never undergone an HIV test. Anonymous rapid HIV testing was accepted by 45-50% of clients. Out of 109 HIV tests conducted during the three study periods, none was reactive. On-site HIV counselling and testing is acceptable among clients of FSW in this urban setting. These individuals represent an unquantified population, a proportion of which has an incomplete understanding of HIV risk in the face of high-risk behaviour, with implications for potential onward transmission to non-commercial sexual partners.

HIV testing and burden of HIV infection in black cancer patients in Johannesburg, South Africa: a cross-sectional study.

Science.gov (United States)

Sengayi, Mazvita; Babb, Chantal; Egger, Matthias; Urban, Margaret I

2015-03-18

HIV infection is a known risk factor for cancer but little is known about HIV testing patterns and the burden of HIV infection in cancer patients. We did a cross-sectional analysis to identify predictors of prior HIV testing and to quantify the burden of HIV in black cancer patients in Johannesburg, South Africa. The Johannesburg Cancer Case-control Study (JCCCS) recruits newly-diagnosed black cancer patients attending public referral hospitals for oncology and radiation therapy in Johannesburg . All adult cancer patients enrolled into the JCCCS from November 2004 to December 2009 and interviewed on previous HIV testing were included in the analysis. Patients were independently tested for HIV-1 using a single ELISA test . The prevalence of prior HIV testing, of HIV infection and of undiagnosed HIV infection was calculated. Multivariate logistic regression models were fitted to identify factors associated with prior HIV testing. A total of 5436 cancer patients were tested for HIV of whom 1833[33.7% (95% CI=32.5-35.0)] were HIV-positive. Three-quarters of patients (4092 patients) had ever been tested for HIV. The total prevalence of undiagnosed HIV infection was 11.5% (10.7-12.4) with 34% (32.0-36.3) of the 1833 patients who tested HIV-positive unaware of their infection. Men >49 years [OR 0.49(0.39-0.63)] and those residing in rural areas [OR 0.61(0.39-0.97)] were less likely to have been previously tested for HIV. Men with at least a secondary education [OR 1.79(1.11-2.90)] and those interviewed in recent years [OR 4.13(2.62 - 6.52)] were likely to have prior testing. Women >49 years [OR 0.33(0.27-0.41)] were less likely to have been previously tested for HIV. In women, having children associated with previous HIV testing. In a study of newly diagnosed black cancer patients in Johannesburg, over a third of HIV-positive patients were unaware of their HIV status. In South Africa black cancer patients should be targeted for opt-out HIV testing.

Design and implementation of strategies for the assurance of quality for sterility testing in the Quality Control Section of the Chilean Nuclear Energy Commission

International Nuclear Information System (INIS)

Olave Carreno, Evelyn Karina

2015-01-01

The Department of Production and Service of the Chilean Nuclear Energy Commission (CCHEN), is an organization dedicated to the production and quality control of radioisotopes and radiopharmaceuticals. To be considered pharmaceutical specialties, the department has implemented a quality assurance system to guarantee compliance with the required standards during manufacturing processes, quality control and distribution. Such products are administered, mostly by via parental; that is why it is extremely important that as an injectable solution is sterile non-pyrogenic. Therefore, the Head of Quality Control Section emphasized the importance of validating sterility testing for these products. In the first instance we proceeded to update the related documentation, as this is one of the essential pillars of a good system of quality assurance, then continuing with the verification of compliance with the physical conditions of the place where the infertility tests are performed (classification of areas from a microbiological point of view). During this process, the proper training of personnel involved in performing environmental testing and sterility testing was performed. Finally, we proceeded to validate the sterility test by the method of direct inoculation three radiopharmaceuticals; also implemented sterility testing by membrane filtration method described in the USP. It was possible to validate the methods of direct inoculation and membrane filtration based on the validation protocol guidelines generated and previously approved by the Chief; demonstrating that in both cases the detection of reference strains of inocula is achieved under 100 cfu (Staphylococcus aureus, Bacillus spizizenii, Pseudomonas aeruginosa, Clostridium sporogenes, Candida albicans, Aspergillus brasiliensis), without interference of two of the products tested and interference of a product by direct inoculation method which was resolved. Based on these results, the documented evidence that

Associations of the stair climb power test with muscle strength and functional performance in people with COPD: A cross-sectional study

DEFF Research Database (Denmark)

Roig, Marc; Eng, Janice J.; MacIntyre, Donna L.

2010-01-01

associations of the SCPT with muscle strength (force-generating capacity) and functional performance. DESIGN: The study was a cross-sectional investigation. METHODS: Twenty-one people with COPD and a predicted mean (SD) percentage of forced expiratory volume in 1 second of 47.2 (12.9) and 21 people who were......: The observational design of the study and the use of a relatively small convenience sample limit the generalizability of the findings. CONCLUSIONS: The SCPT is a simple and safe test associated with measures of functional performance in people with COPD. People with COPD show deficits on the SCPT. However, the SCPT......BACKGROUND: The Stair Climb Power Test (SCPT) is a functional test associated with leg muscle power in older people. OBJECTIVE: The purposes of this study were to compare the results of the SCPT in people with chronic obstructive pulmonary disease (COPD) and people who were healthy and to explore...

Manufacturing of In-Pile Test Section(IPS) Mock-up for the 3-Pin Fuel Test Loop

Energy Technology Data Exchange (ETDEWEB)

Lee, J. M.; Park, K. N.; Chi, D. Y. (and others)

2005-10-15

Manufacturing process of IPS Mock-up was initiated in late of 2003 with DAEWOO Precision industries Company. Manufacturing drawings due to detail drawings are composed of Outer assembly and Inner assembly. Welding of IPS Mock-up was performed by the GMAW(Gas Metal Arc Welding) process. After the welding process, non-destructive examination was conducted. Leak test was performed to the Main cooling water part and Neon gas inter-space gap part by the He gas injection with the pressure of 6.0 kg{sub f}/cm{sup 2} and 30 minutes holding time. the result was shown that there was no leak at the Neon gas inter-space gap part but leak was occurred at Main cooling water part according to imperfect screw of purge plug. so, it was re-finished and test was performed to certify the leak tightness. To satisfy the HANARO Limiting Operation Condition, IPS should be tested ahead of installation at the HANARO reactor by the use of test facilities. IPS Mock-up and its test facilities will be designed and used for the test of 'HANARO flow tube pressure drop', 'IPS inner pressure drop' and 'IPS inner vibration'.

Validation of evaluated neutron standard cross sections

International Nuclear Information System (INIS)

Badikov, S.; Golashvili, T.

2008-01-01

Some steps of the validation and verification of the new version of the evaluated neutron standard cross sections were carried out. In particular: -) the evaluated covariance data was checked for physical consistency, -) energy-dependent evaluated cross-sections were tested in most important neutron benchmark field - 252 Cf spontaneous fission neutron field, -) a procedure of folding differential standard neutron data in group representation for preparation of specialized libraries of the neutron standards was verified. The results of the validation and verification of the neutron standards can be summarized as follows: a) the covariance data of the evaluated neutron standards is physically consistent since all the covariance matrices of the evaluated cross sections are positive definite, b) the 252 Cf spectrum averaged standard cross-sections are in agreement with the evaluated integral data (except for 197 Au(n,γ) reaction), c) a procedure of folding differential standard neutron data in group representation was tested, as a result a specialized library of neutron standards in the ABBN 28-group structure was prepared for use in reactor applications. (authors)

V/STOL Tandem Fan transition section model test. [in the Lewis Research Center 10-by-10 foot wind tunnel

Science.gov (United States)

Simpkin, W. E.

1982-01-01

An approximately 0.25 scale model of the transition section of a tandem fan variable cycle engine nacelle was tested in the NASA Lewis Research Center 10-by-10 foot wind tunnel. Two 12-inch, tip-turbine driven fans were used to simulate a tandem fan engine. Three testing modes simulated a V/STOL tandem fan airplane. Parallel mode has two separate propulsion streams for maximum low speed performance. A front inlet, fan, and downward vectorable nozzle forms one stream. An auxilliary top inlet provides air to the aft fan - supplying the core engine and aft vectorable nozzle. Front nozzle and top inlet closure, and removal of a blocker door separating the two streams configures the tandem fan for series mode operations as a typical aircraft propulsion system. Transition mode operation is formed by intermediate settings of the front nozzle, blocker door, and top inlet. Emphasis was on the total pressure recovery and flow distortion at the aft fan face. A range of fan flow rates were tested at tunnel airspeeds from 0 to 240 knots, and angles-of-attack from -10 to 40 deg for all three modes. In addition to the model variables for the three modes, model variants of the top inlet were tested in the parallel mode only. These lip variables were: aft lip boundary layer bleed holes, and Three position turning vane. Also a bellmouth extension of the top inlet side lips was tested in parallel mode.

Conceptual Design for the In-Pile Test Section(IPS) Improvement

Energy Technology Data Exchange (ETDEWEB)

Lee, Jong Min; Shim, Bong Sik; Lee, Chung Young; Chi, Dae Young; Park, Su Ki; Ahn, Sung Ho; Kim, Young Ki; Lee, Kye Hong; Kim, Kwan Hyun

2009-01-15

Conceptual design on the IPS, instrumentation and 1/4' Tubing, test fuel supports, test fuel inspection station and inner assembly O-ring replacement was suggested for their improvement. There is a need Jacking bolt on the Top flange for the inner assembly disassemble from the outer assembly and the replacement about the top flange O-ring to metal gasket to secure pressure boundary. Mechanical sealing was suggested instead of brazing. Instrumentation and tubing route should be modified for the reduction of bending and protection from unexpected occasion. Concept on the test fuel inspection station under the consideration of canal dimension. Top flange Bolt handling tool, O-ring replacement platform and O-ring replacement tool was designed for the O-ring replacement at the inner assembly.

Testing of ENDF/B cross section data in the Californium-252 neutron benchmark field

International Nuclear Information System (INIS)

Mannhart, W.

1979-01-01

The fission neutron field of 252 Cf presently represents one of the most well-known neutron benchmark fields. For 13 neutron reactions which are of importance in reactor metrology, measurements of spectrum-averaged cross sections, [sigma], performed in this neutron field were compared with calculated average cross sections. This comparison allows one to draw conclusions as to the quality of different sigma(E) data taken from ENDF/B-IV, from ENDF/B-V, and from recent experiments and used in the calculation of average cross sections. The comparison includes an uncertainty analysis regarding the different uncertainty contributions of [sigma], of sigma(E), and of the spectral distribution of 252 Cf fission neutrons. Additionally, in a few examples, sensitivity studies were carried out. The sensitivity of the spectrum-averaged cross sections to individual characteristics of the sigma(E) data, such as normalization factors or shifts in the energy scale, was investigated. Similarly, the sensitivity of [sigma] to the spectral distribution of 252 Cf was determined. 4 figures, 2 tables

Utilization of Advanced Diagnostic Methods for Texture and Rut Depth Analysis on a Testing Pavement Section

Directory of Open Access Journals (Sweden)

Slabej Martin

2015-05-01

Full Text Available Qualitative characteristics of pavement in wide range reflects the pavement serviceability, which is a summary of the characteristics of the pavement, providing a fast, smooth, economical and especially safe driving of motor-vehicles. The target factor of pavement serviceability and safety of roads represents the quality of their surface properties. In the framework of research activities performed in the Research Centre founded under the auspices of University of Žilina, individual parameters of pavement serviceability were monitored by pavement surface scanning. This paper describes the creation of a 3D - road surface model and its analysis and evaluation from the viewpoint of two pavement serviceability parameters - the rut depth and texture. Measurements were performed on an experimental pavement section used contemporary in an Accelerated Pavement Testing experiment. The long-term goal is to ascertain functions predicting degradation of these two pavement serviceability parameters.

Utilization of HIV testing services among pregnant mothers in low income primary care settings in northern Ethiopia: a cross sectional study.

Science.gov (United States)

Alemu, Yihun Mulugeta; Ambaw, Fentie; Wilder-Smith, Annelies

2017-06-24

HIV testing of women in child bearing age is an entry point for preventing mother-to-child transmission of HIV (MTCT). This study aims to identify the proportion of women tested for HIV and to determine factors associated with utilization of HIV testing services among pregnant mothers in primary care settings in northern Ethiopia. A cross sectional study was conducted in 416 pregnant women from four primary care centers between October 2, 2012 and May 31, 2013 in East Gojjam, Ethiopia. The proportion of mothers who tested for HIV was 277(67%). Among mothers who were not tested for HIV, lack of HIV risk perception (n = 68, 49%) was a major self-reported barrier for HIV testing. A multivariable logistic regression analysis showed that those pregnant women who had comprehensive knowledge about MTCT had an Adjusted Odd Ratio (AOR) of 3.73 (95% CI: 1.56, 8.94), having comprehensive knowledge on prevention of mother to child transmission (PMTCT) of HIV an AOR of 2.56 (95% CI: 1.26, 5.19), and a favorable attitude towards persons living with HIV an AOR of 2.42 (95%CI, 1.20, 4.86) were more likely to be tested for HIV. One third of pregnant women had never been tested for HIV until the time of the study. Efforts should be made to improve mother's knowledge about MTCT and PMTCT to increase uptake of HIV testing. Enhancing mother's HIV risk perception to scale up HIV testing in resource limited setting is highly recommended.

Associations between cadmium exposure and neurocognitive test scores in a cross-sectional study of US adults.

Science.gov (United States)

Ciesielski, Timothy; Bellinger, David C; Schwartz, Joel; Hauser, Russ; Wright, Robert O

2013-02-05

Low-level environmental cadmium exposure and neurotoxicity has not been well studied in adults. Our goal was to evaluate associations between neurocognitive exam scores and a biomarker of cumulative cadmium exposure among adults in the Third National Health and Nutrition Examination Survey (NHANES III). NHANES III is a nationally representative cross-sectional survey of the U.S. population conducted between 1988 and 1994. We analyzed data from a subset of participants, age 20-59, who participated in a computer-based neurocognitive evaluation. There were four outcome measures: the Simple Reaction Time Test (SRTT: visual motor speed), the Symbol Digit Substitution Test (SDST: attention/perception), the Serial Digit Learning Test (SDLT) trials-to-criterion, and the SDLT total-error-score (SDLT-tests: learning recall/short-term memory). We fit multivariable-adjusted models to estimate associations between urinary cadmium concentrations and test scores. 5662 participants underwent neurocognitive screening, and 5572 (98%) of these had a urinary cadmium level available. Prior to multivariable-adjustment, higher urinary cadmium concentration was associated with worse performance in each of the 4 outcomes. After multivariable-adjustment most of these relationships were not significant, and age was the most influential variable in reducing the association magnitudes. However among never-smokers with no known occupational cadmium exposure the relationship between urinary cadmium and SDST score (attention/perception) was significant: a 1 μg/L increase in urinary cadmium corresponded to a 1.93% (95%CI: 0.05, 3.81) decrement in performance. These results suggest that higher cumulative cadmium exposure in adults may be related to subtly decreased performance in tasks requiring attention and perception, particularly among those adults whose cadmium exposure is primarily though diet (no smoking or work based cadmium exposure). This association was observed among exposure levels

14 CFR 35.40 - Functional test.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Functional test. 35.40 Section 35.40... STANDARDS: PROPELLERS Tests and Inspections § 35.40 Functional test. The variable-pitch propeller system must be subjected to the applicable functional tests of this section. The same propeller system used in...

40 CFR 53.64 - Test procedure: Static fractionator test.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 5 2010-07-01 2010-07-01 false Test procedure: Static fractionator test. 53.64 Section 53.64 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Performance Characteristics of Class II Equivalent Methods for PM2.5 § 53.64 Test procedure: Static...

Effects of Music during Multiple Cesarean Section Delivery.

Science.gov (United States)

Handan, Eren; Sahiner, Nejla Canbulat; Bal, Meltem Demirgoz; Dissiz, Melike

2018-03-01

This experimental study was conducted to determine the level of anxiety in women undergoing multiple cesarean section. Sixty multiple cesarean section referrals were randomly assigned to either the experimental or control groups. Data was collected at the Karaman Public Health Hospital in Turkey, from June 2015 to June 2016. Songs chosen earlier by the patients were played during the cesarean section procedure for the experimental group. The control group was studied without music. Data was collected using a questionnaire form, and Visual Analogue Scale (VAS) was used to determine the anxiety levels. The t-test and chi-square test were used to analyse statistically significant differences between the groups. The VAS scores before and during the procedure showed significantly lower scores for the experimental group, compared to the control group (p<0.05). Music therapy reduces the physiological and cognitive responses of anxiety in patients undergoing multiple cesarean section, and can be used in the clinical practice.

Knowledge, attitudes and practices of voluntary HIV counselling and testing among rural migrants in central China: a cross-sectional study.

Science.gov (United States)

Zhang, Tiejun; Zhang, Jinling; Gao, Meiyang; He, Na; Detels, Roger

2012-04-01

To document knowledge, attitudes and practices of voluntary HIV counselling and testing (VCT) among rural migrants in central China. A cross-sectional study with face-to-face anonymous questionnaire interviews was conducted using a structured questionnaire. Among 1280 participants, 87.9% reported having had sexual intercourse during their lifetime, with 69% of singles reporting having had sexual intercourse and 49.1% having had sex in the past month. Only 21% always used condoms, 84.4% knew HIV infection was diagnosed through blood testing, 56.6% had heard of VCT, but only 3.8% perceived their own risk for HIV infection. Only 43 (2.3%) had ever been tested for HIV, and none had ever been tested at a VCT site. About two-thirds (64.5%) would be willing to use VCT services upon awareness of HIV risk. A logistic regression model showed that females, those having little knowledge of HIV/AIDS, those unwilling to work with HIV-infected individuals, never having been tested for HIV and having low awareness regarding HIV risk were less willing to use VCT. The results of this study indicated that much greater efforts are needed to improve HIV/AIDS and VCT knowledge, to promote safer sex and to improve VCT acceptance among rural migrants in central China, particularly those engaging in risky behaviours.

Experimental Testing of Innovative Cold-Formed "GEB" Section / Badania Eksperymentalne Innowacyjnego Kształtownika Giętego Na Zimno Typu "Geb"

Science.gov (United States)

Łukowicz, Agnieszka; Urbańska-Galewska, Elżbieta; Gordziej-Zagórowska, Małgorzata

2015-03-01

One of the major advantages of light gauge steel structures made of cold-formed steel sections is their low weight so the production of typical single-storey steel structures of this kind of profiles is still rising. The well known profiles, e.o. Z-sections, C-sections and the so called hat-sections studied and described in the literature, are used mainly as purlins or truss components. A new profile GEB was patented for the use for primary load-bearing member in fabricated steel frames. According to the code [1] every novel cross section should be tested to assign the deformation shape and bearing capacity. The paper deals with the numerical and experimental research of bearing capacity of cold formed GEB profiles. The deformation shape and limit load was obtained from bending tests. The GEB cross section bearing capacity was also determined according to codes [1, 2]. Jedną z najważniejszych zalet lekkich konstrukcji metalowych, wytwarzanych z kształtowników giętych na zimno, jest ich mała masa, dlatego też, producenci coraz częściej wykorzystują możliwości profili giętych do wytwarzania typowych konstrukcji halowych w budownictwie systemowym. Proces gięcia na zimno, pozwala na formowanie różnego rodzaju przekrojów poprzecznych, które mogą być wykorzystywane jako elementy konstrukcji. Typowe kształty elementów. tzn. Z, C oraz tzw. przekroje kapeluszowe, które zostały przebadane i opisane w literaturze, wykorzystuje się głównie jako płatwie lub części składowe wiązarów kratowych. Nowo opatentowany przekrój typu GEB ma być wykorzystany jako element nośny konstrukcji ramowych. W związku z tym innowacyjny kształt oraz parametry geometryczne przekroju takiego kształtownika, związane z możliwością jego wyprodukowania oraz z warunkami nośności, stateczności oraz sztywności, muszą być optymalne. Według normy PN-EN 1993-1-3, każdy nowo uformowany przekrój powinien być przebadany pod kątem nośności elementu i formy

Status of neutron dosimetry cross sections

International Nuclear Information System (INIS)

Griffin, P.J.; Kelly, J.G.

1992-01-01

Several new cross section libraries, such as ENDF/B-VI(release 2), IRDF-90,JEF-2.2, and JENDL-3 Dosimetry, have recently been made available to the dosimetry community. the Sandia National Laboratories (SNL) Radiation Metrology Laboratory (RML) has worked with these libraries since pre-release versions were available. this paper summarizes the results of the intercomparison and testing of dosimetry cross sections. As a result of this analysis, a compendium of the best dosimetry cross sections was assembled from the available libraries for use within the SNL RML. this library, referred to as the SNLRML Library, contains 66 general dosimetry sensors and 3 special dosimeters unique to the RML sensor inventory. The SNLRML cross sections have been put into a format compatible with commonly used spectrum determination codes

Testing of cross-section functionals in the unresolved resonance region

International Nuclear Information System (INIS)

Koshcheev, V.N.; Krivtsov, A.S.; Sinitsa, V.V.; Ukraintsev, V.F.

1994-01-01

The results of a comparison of the GRUCON, MMK and NJOY data processing codes in the treatment of evaluated neutron data in the unresolved resonance region are presented. The sets of average resonance parameters of 238 U and 239 Pu isotopes, which have been published by Munos-Cobos et al., and Ribon et al., were used in this exercise. Average cross-sections, self-shielding factors and Doppler broadening self-shielding factors are compared with the original results presented by the above-mentioned authors. Conclusions regarding the reliability of the neutron data processing codes are made. (author). 6 refs, 7 tabs

Effect of home-based HIV counselling and testing on stigma and risky sexual behaviours: serial cross-sectional studies in Uganda.

Science.gov (United States)

Nuwaha, Fred; Kasasa, Simon; Wana, Godwill; Muganzi, Elly; Tumwesigye, Elioda

2012-06-04

A large, district-wide, home-based HIV counselling and testing (HBHCT) programme was implemented in Bushenyi district of Uganda from 2004 to 2007. This programme provided free HBHCT services to all consenting adults of Bushenyi district and had a very high uptake and acceptability. We measured population-level changes in knowledge of HIV status, stigma and HIV-risk behaviours before and after HBHCT to assess whether widespread HBHCT had an effect on trends of risky sexual behaviours and on stigma and discrimination towards HIV. Serial cross-sectional surveys were carried out before and after the implementation of HBHCT programme in Bushenyi district of Uganda. A total of 1402 randomly selected adults (18 to 49 years) were interviewed in the baseline survey. After the implementation, a different set of randomly selected 1562 adults was interviewed using the same questionnaire. Data was collected on socio-demographic characteristics, sexual behaviour, whether respondents had ever tested for HIV and stigma and discrimination towards HIV/AIDS. The proportion of people who had ever tested for HIV increased from 18.6% to 62% (pHIV test result with a sexual partner increased from 41% to 57% (pHIV services especially in areas where access to HCT is low.

Meeting cross-section requirements for nuclear-energy design

Energy Technology Data Exchange (ETDEWEB)

Weisbin, C.R.; de Saussure, G.; Santoro, R.T. (Oak Ridge National Lab., TN (USA)); Gilai, T. (Ben-Gurion Univ. of the Negev, Beersheba (Israel))

1982-01-01

Current requirements in cross-section data that are essential to nuclear-energy programmes are summarized and explained and some insight into how these data might be obtained is provided. The six sections of the paper describe: design parameters and target accuracies; data collection, evaluation and analysis; determination of high-accuracy differential nuclear data for technological applications; status of selected evaluated nuclear data; analysis of benchmark testing; identification of important cross sections and inferred needs.

Dielectronic recombination cross sections for H-like ions

International Nuclear Information System (INIS)

Pindzola, M.S.; Badnell, N.R.; Griffin, D.C.

1990-01-01

Dielectronic recombination cross sections for several H-like atomic ions are calculated in an isolated-resonance, distorted-wave approximation. Fine-structure and configuration-interaction effects are examined in detail for the O 7+ cross section. Hartree-Fock, intermediate-coupled, multiconfiguration dielectronic recombination cross sections for O 7+ are then compared with the recent experimental measurements obtained with the Test Storage Ring in Heidelberg. The cross-section spectra line up well in energy and the shape of the main resonance structures are comparable. The experimental integrated cross sections differ by up to 20% from theory, but this may be due in part to uncertainties in the electron distribution function

Tests of three tapered airfoils based on the N.A.C.A. 2200, the N.A.C.A.-M6, and the Clark Y sections

Science.gov (United States)

Anderson, Raymond F

1934-01-01

Three tapered airfoils based on the N.A.C.A. 2200, the N.A.C.A.-M6, and the Clark Y sections were tested in the variable-density wind tunnel at a Reynolds Number of approximately 3,100,000. The models, which were of aspect ratio 6, had constant core center sections and rounded tips, and tapered in thickness from 18 percent at the roots to 9 percent at the tips. The aerodynamic characteristics are given by the usual dimensionless coefficients plotted for both positive and negative angles of attack and by effective profile-drag coefficients plotted against lift coefficients.

ENDF/B Thermal Data Testing

CERN Document Server

McCrosson, F J

2001-01-01

The thermal data testing group is concerned with establishing the merit of ENDF/B cross sections for the analysis of thermal systems. The integral experiments used in the testing are designed to analyze each of the phenomena identified in the familiar four-factor formula. For brevity, only the testing of the cross sections in uranium systems is described in this report.

Automated Cross-Sectional Measurement Method of Intracranial Dural Venous Sinuses.

Science.gov (United States)

Lublinsky, S; Friedman, A; Kesler, A; Zur, D; Anconina, R; Shelef, I

2016-03-01

MRV is an important blood vessel imaging and diagnostic tool for the evaluation of stenosis, occlusions, or aneurysms. However, an accurate image-processing tool for vessel comparison is unavailable. The purpose of this study was to develop and test an automated technique for vessel cross-sectional analysis. An algorithm for vessel cross-sectional analysis was developed that included 7 main steps: 1) image registration, 2) masking, 3) segmentation, 4) skeletonization, 5) cross-sectional planes, 6) clustering, and 7) cross-sectional analysis. Phantom models were used to validate the technique. The method was also tested on a control subject and a patient with idiopathic intracranial hypertension (4 large sinuses tested: right and left transverse sinuses, superior sagittal sinus, and straight sinus). The cross-sectional area and shape measurements were evaluated before and after lumbar puncture in patients with idiopathic intracranial hypertension. The vessel-analysis algorithm had a high degree of stability with <3% of cross-sections manually corrected. All investigated principal cranial blood sinuses had a significant cross-sectional area increase after lumbar puncture (P ≤ .05). The average triangularity of the transverse sinuses was increased, and the mean circularity of the sinuses was decreased by 6% ± 12% after lumbar puncture. Comparison of phantom and real data showed that all computed errors were <1 voxel unit, which confirmed that the method provided a very accurate solution. In this article, we present a novel automated imaging method for cross-sectional vessels analysis. The method can provide an efficient quantitative detection of abnormalities in the dural sinuses. © 2016 by American Journal of Neuroradiology.

Rocketball Test Facility

Data.gov (United States)

Federal Laboratory Consortium — This test facility offers the capability to emulate and measure guided missile radar cross-section without requiring flight tests of tactical missiles. This facility...

49 CFR 179.500-7 - Physical tests.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Physical tests. 179.500-7 Section 179.500-7...-7 Physical tests. (a) Physical tests shall be made on two test specimens 0.505 inch in diameter... tank. These test specimen ring sections or prolongations shall be heat treated, with the necked-down...

Selective reporting of antibiotic susceptibility test results in European countries: an ESCMID cross-sectional survey.

Science.gov (United States)

Pulcini, Céline; Tebano, Gianpiero; Mutters, Nico T; Tacconelli, Evelina; Cambau, Emmanuelle; Kahlmeter, Gunnar; Jarlier, Vincent

2017-02-01

Selective reporting of antibiotic susceptibility test (AST) results is one possible laboratory-based antibiotic stewardship intervention. The primary aim of this study was to identify where and how selective reporting of AST results is implemented in Europe both in inpatient and in outpatient settings. An ESCMID cross-sectional, self-administered, internet-based survey was conducted among all EUCIC (European Committee on Infection Control) or EUCAST (European Committee on Antimicrobial Susceptibility Testing) national representatives in Europe and Israel. Of 38 countries, 36 chose to participate in the survey. Selective reporting of AST results was implemented in 11/36 countries (31%), was partially implemented in 4/36 (11%) and was limited to local initiatives or was not adopted in 21/36 (58%). It was endorsed as standard of care by health authorities in only three countries. The organisation of selective reporting was everywhere discretionally managed by each laboratory, with a pronounced intra- and inter-country variability. The most frequent application was in uncomplicated community-acquired infections, particularly urinary tract and skin and soft-tissue infections. The list of reported antibiotics ranged from a few first-line options, to longer reports where only last-resort antibiotics were hidden. Several barriers to implementation were reported, mainly lack of guidelines, poor system support, insufficient resources, and lack of professionals' capability. In conclusion, selective reporting of AST results is poorly implemented in Europe and is applied with a huge heterogeneity of practices. Development of an international framework, based on existing initiatives and identified barriers, could favour its dissemination as one important element of antibiotic stewardship programmes. Copyright © 2017 Elsevier B.V. and International Society of Chemotherapy. All rights reserved.

MCO Engineering Test Report Fuel Basket Handling Grapple Acceptance Test

International Nuclear Information System (INIS)

CHENAULT, D.M.

2000-01-01

Acceptance testing of the production SNF Fuel Basket lift grapples to the required 150 percent maximum lift load is documented herein. The report shows the results affirming the proof test passage. The primary objective of this test was to confirm the load rating of the grapple per applicable requirements of ANSI 14 6 American National Standard For Radioactive Materials Special Lifting Devices for Shipping Containers Weighing 10,000 pounds (4500kg) or More. The above Standard requires a load test of 150% of the design load which must be held for a minimum of 10 minutes followed by a Liquid Penetrant or Magnetic Particle examination of critical areas and welds in accordance with the ANSI/ASME Boiler and Pressure Vessel Code 1989 Section 111 Division 1 section NF 5350

Demonstration test for reliability of valves for atomic power plants

International Nuclear Information System (INIS)

Hosaka, Shiro

1978-01-01

The demonstration test on the reliability of valves for atomic power plants being carried out by the Nuclear Engineering Test Center is reported. This test series is conducted as six-year project from FY 1976 to FY 1981 at the Isogo Test Center. The demonstration test consists of (1) environmental test, (2) reaction force test, (3) vibration test, (4) stress measurement test, (5) operational characteristic test, (6) flow resistance coefficient measuring test, (7) leakage test and (8) safety valve and relief valve test. These contents are explained about the special requirements for nuclear use, for example, the enviornmental condition after the design base accident of PWRs and BWRs, the environmental test sequence for isolation valves of containment vessels under the emergency condition, the seismic test condition for valves of nuclear use, the various stress measurements under thermal transient conditions, the leak test after 500 cycles between the normal operating conditions for PWRs and BWRs and the start up conditions and so on. As for the testing facilities, the whole flow diagram is shown, in which the environmental test section, the vibration test section, the steam test section, the hot water test section, the safety valve test section and main components are included. The specifications of each test section and main components are presented. (Nakai, Y.)

Science Library of Test Items. Volume Thirteen. Mastery Testing Program. [Mastery Tests Series 5.] Tests M51-M65.

Science.gov (United States)

New South Wales Dept. of Education, Sydney (Australia).

As part of a series of tests to measure mastery of specific skills in the natural sciences, copies of tests 51 through 65 include: (51) interpreting atomic and mass numbers; (52) extrapolating from a geological map; (53) matching geological sections and maps; (54) identifying parts of the human eye; (55) identifying the functions of parts of a…

GRE math tests

CERN Document Server

Kolby, Jeff

2014-01-01

Twenty-three GRE Math Tests! The GRE math section is not easy. There is no quick fix that will allow you to ""beat"" the section. But GRE math is very learnable. If you study hard and master the techniques in this book, your math score will improve--significantly! The GRE cannot be ""beaten."" But it can be mastered--through hard work, analytical thought, and by training yourself to think like a test writer. Many of the problems in this book are designed to prompt you to think like a test writer. For example, you will find ""Duals."" These are pairs of similar problems in which only one prop

Preliminary Options Assessment of Versatile Irradiation Test Reactor

Energy Technology Data Exchange (ETDEWEB)

Sen, Ramazan Sonat [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2017-01-01

The objective of this report is to summarize the work undertaken at INL from April 2016 to January 2017 and aimed at analyzing some options for designing and building a versatile test reactor; the scope of work was agreed upon with DOE-NE. Section 2 presents some results related to KNK II and PRISM Mod A. Section 3 presents some alternatives to the VCTR presented in [ ] as well as a neutronic parametric study to assess the minimum power requirement needed for a 235U metal fueled fast test reactor capable to generate a fast (>100 keV) flux of 4.0 x 1015 n /cm2-s at the test location. Section 4 presents some results regarding a fundamental characteristic of test reactors, namely displacement per atom (dpa) in test samples. Section 5 presents the INL assessment of the ANL fast test reactor design FASTER. Section 6 presents a summary.

On Preliminary Test Estimator for Median

OpenAIRE

Okazaki, Takeo; 岡崎, 威生

1990-01-01

The purpose of the present paper is to discuss about estimation of median with a preliminary test. Two procedures are presented, one uses Median test and the other uses Wilcoxon two-sample test for the preliminary test. Sections 3 and 4 give mathematical formulations of such properties, including mean square errors with one specified case. Section 5 discusses their optimal significance levels of the preliminary test and proposes their numerical values by Monte Carlo method. In addition to mea...

LHCb cross-section measurements with heavy flavour jets

CERN Multimedia

Michielin, Emanuele

2017-01-01

Cross-section measurements of jets originating from the hadronization of beauty ($b$) and charm ($c$) quarks at LHCb give the unique opportunity to probe Parton Distribution Functions (PDFs) at low and large momentum fraction and to test the Standard Model in the forward region. In this poster the production of $t\\bar{t}$ pairs in the forward region, the measurement of the $W+b\\bar{b}$ and $W+c\\bar{c}$ cross-section and the measurement of the $Z\\rightarrow b\\bar{b}$ cross-section are presented.

A comparison between burn-out data for 19-rod cluster test-sections cooled by Freon-12 at 155 lb/in2 (abs), and by water at 1000 lb/in2 in vertical upflow

International Nuclear Information System (INIS)

Stevens, G.F.; Wood, R.W.

1966-01-01

Previous experiments on the Winfrith Freon Rig have produced scaling factors which relate these Freon experiments to the corresponding experiments in water with an accuracy of about 10%. It has also been found that the Freon rig is accurate, economical and easy to use. The scaling factors so obtained have now been tested against data for 19-rod clusters which had previously been tested at Columbia University. This report presents the results of the rod cluster tests in which comparison is made between Freon-12 and water for three test-sections which differ in the means of spacing the individual rods. All the test-sections were heated uniformly with respect to length, but had a radial flux depression of nominally 0.70/1.0. The results provide strong evidence that the scaling factor method using Freon-12 at 155 lb/in 2 (abs) is a useful technique for predicting the behaviour at burn-out of complicated test-sections cooled by boiling water at 1000 lb/in 2 with only one-eighteenth of the power required for the water experiment. In particular, the Freon tests reproduce closely the relative burn-out powers previously measured in water. It has also been found that repeated rebuilding of a nominally unchanged cluster from the same components can produce burn-out powers differing by ± 6%. This new result illustrates the power and value of the Freon technique. (author)

40 CFR 1039.505 - How do I test engines using steady-state duty cycles, including ramped-modal testing?

Science.gov (United States)

2010-07-01

...-state duty cycles, including ramped-modal testing? 1039.505 Section 1039.505 Protection of Environment... duty cycles, including ramped-modal testing? This section describes how to test engines under steady-state conditions. In some cases, we allow you to choose the appropriate steady-state duty cycle for an...

Cross sections required for FMIT dosimetry

International Nuclear Information System (INIS)

Gold, R.; McElroy, W.N.; Lippincott, E.P.; Mann, F.M.; Oberg, D.L.; Roberts, J.H.; Ruddy, F.H.

1980-01-01

The Fusion Materials Irradiation Test (FMIT) facility, currently under construction, is designed to produce a high flux of high energy neutrons for irradiation effects experiments on fusion reactor materials. Characterization of the flux-fluence-spectrum in this rapidly varying neutron field requires adaptation and extension of currently available dosimetry techniques. This characterization will be carried out by a combination of active, passive, and calculational dosimetry. The goal is to provide the experimenter with accurate neutron flux-fluence-spectra at all positions in the test cell. Plans have been completed for a number of experimental dosimetry stations and provision for these facilities has been incorporated into the FMIT design. Overall needs of the FMIT irradiation damage program delineate goal accuracies for dosimetry that, in turn, create new requirements for high energy neutron cross section data. Recommendations based on these needs have been derived for required cross section data and accuracies

Get Tested for Colorectal Cancer

Science.gov (United States)

... Print This Topic En español Get Tested for Colorectal Cancer Browse Sections The Basics Overview What to Expect ... section Overview 2 of 6 sections The Basics: Colorectal Cancer What is colorectal cancer? Colorectal cancer is a ...

Thermohydraulic tests in nuclear fuel model

International Nuclear Information System (INIS)

Ladeira, L.C.D.; Navarro, M.A.

1984-01-01

The main experimental works performed in the Thermohydraulics Laboratory of the NUCLEBRAS Nuclear Technology Development Center, in the field of thermofluodynamics are briefly described. These works include the performing of steady-state flow tests in single tube test sections, and the design and construction of a rod bundle test section, which will be also used for those kind of testes. Mention is made of the works to be performed in the near future, related to steady-state and transient flow tests. (Author) [pt

9 CFR 113.39 - Cat safety tests.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Cat safety tests. 113.39 Section 113... Procedures § 113.39 Cat safety tests. The safety tests provided in this section shall be conducted when... recommended for use in cats. (a) The cat safety test provided in this paragraph shall be used when the Master...

40 CFR 89.410 - Engine test cycle.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Engine test cycle. 89.410 Section 89... Procedures § 89.410 Engine test cycle. (a) Emissions shall be measured using one of the test cycles specified...) through (a)(4) of this section. These cycles shall be used to test engines on a dynamometer. (1) The 8...

9 CFR 113.40 - Dog safety tests.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Dog safety tests. 113.40 Section 113... Procedures § 113.40 Dog safety tests. The safety tests provided in this section shall be conducted when... recommended for use in dogs. Serials which are not found to be satisfactory when tested pursuant to the...

Will an unsupervised self-testing strategy for HIV work in health care workers of South Africa? A cross sectional pilot feasibility study.

Science.gov (United States)

Pant Pai, Nitika; Behlim, Tarannum; Abrahams, Lameze; Vadnais, Caroline; Shivkumar, Sushmita; Pillay, Sabrina; Binder, Anke; Deli-Houssein, Roni; Engel, Nora; Joseph, Lawrence; Dheda, Keertan

2013-01-01

In South Africa, stigma, discrimination, social visibility and fear of loss of confidentiality impede health facility-based HIV testing. With 50% of adults having ever tested for HIV in their lifetime, private, alternative testing options are urgently needed. Non-invasive, oral self-tests offer a potential for a confidential, unsupervised HIV self-testing option, but global data are limited. A pilot cross-sectional study was conducted from January to June 2012 in health care workers based at the University of Cape Town, South Africa. An innovative, unsupervised, self-testing strategy was evaluated for feasibility; defined as completion of self-testing process (i.e., self test conduct, interpretation and linkage). An oral point-of-care HIV test, an Internet and paper-based self-test HIV applications, and mobile phones were synergized to create an unsupervised strategy. Self-tests were additionally confirmed with rapid tests on site and laboratory tests. Of 270 health care workers (18 years and above, of unknown HIV status approached), 251 consented for participation. Overall, about 91% participants rated a positive experience with the strategy. Of 251 participants, 126 evaluated the Internet and 125 the paper-based application successfully; completion rate of 99.2%. All sero-positives were linked to treatment (completion rate:100% (95% CI, 66.0-100). About half of sero-negatives were offered counselling on mobile phones; completion rate: 44.6% (95% CI, 38.0-51.0). A majority of participants (78.1%) were females, aged 18-24 years (61.4%). Nine participants were found sero-positive after confirmatory tests (prevalence 3.6% 95% CI, 1.8-6.9). Six of nine positive self-tests were accurately interpreted; sensitivity: 66.7% (95% CI, 30.9-91.0); specificity:100% (95% CI, 98.1-100). Our unsupervised self-testing strategy was feasible to operationalize in health care workers in South Africa. Linkages were successfully operationalized with mobile phones in all sero

Factors associated with HIV testing among young men who have sex with men in Myanmar: a cross-sectional study.

Science.gov (United States)

Pham, Minh D; Aung, Poe Poe; Paing, Aye Kyawt; Pasricha, Naanki; Agius, Paul A; Tun, Waimar; Bajracharya, Ashish; Luchters, Stanley

2017-11-01

In Myanmar, men who have sex with men (MSM) experience high risk of HIV infection. However, access to HIV testing and prevention services remains a challenge among this marginalized population. The objective of this study was to estimate population prevalence and correlates of prior HIV testing among young MSM (YMSM) and informs the development of HIV testing and intervention programmes that respond to the specific needs of this population. Five hundred and eighty-five YMSM aged 18 to 24 years were recruited using respondent-driven sampling (RDS) in a cross-sectional survey conducted in six townships of Myanmar. RDS-adjusted population estimates were calculated to estimate prevalence of HIV testing; RDS-weighted logistic regression was used to examine correlates of HIV testing in the past 6 months and in a lifetime. There were 12 participants who reported receiving a HIV-positive test; of those, five were tested in the past 6 months. The RDS-weighted prevalence estimates of lifetime (any prior) HIV testing was 60.6% (95% CI: 53.3% to 66.4%) and of recent (≤ 6 months) HIV testing was 50.1% (95% CI: 44.1% to 55.5%). In multivariable analysis, sexual identity was associated with lifetime but not recent HIV testing. Lifetime and recent HIV testing were associated with having three or more male sexual partners in the past 12 months (adjusted ORs (aORs) = 2.28, 95% CIs: 1.21 to 4.32 and 2.69, 95% CI: 1.59 to 4.56), having good HIV-related knowledge (aORs = 1.96, 95% CIs: 1.11 to 3.44 and 1.77, 95% CI: 1.08 to 2.89), reporting high HIV testing self-efficacy (aORs = 13.5, 95% CIs: 6.0 to 30.1 and 9.81, 95% CI: 4.27 to 22.6) and having access to and use of non-HIV health-related services in the past 12 months (aORs = 13.2, 95% CIs: 6.85 to 25.6 and 7.15, 95% CI: 4.08 to 12.5) respectively. HIV testing coverage among YMSM aged 18 to 24 years old in Myanmar is still suboptimal. Integrated HIV testing and prevention services in existing health service

Drift scale test status report (Chapters 1-9)

Energy Technology Data Exchange (ETDEWEB)

Lin, W., LLNL

1998-07-01

The Drift-Scale Test (DST) is one of the thermal tests being conducted in the Exploratory Studies Facility (ESF) at Yucca Mountain, Nevada, site of the potential repository for high-level nuclear waste. One of the DST`s major objectives is to study the coupled thermal-hydrologic-chemical-mechanical (THCM) processes at the potential repository`s horizon. The objectives, test design, and test layouts of the DST are included in a previous test design report. this report present results and analysis of several difference measurements made in the DST by researchers at Lawrence Livermore National Laboratory through the second quarter of the heating phase. Sections 1.1 and 1.2 describe the layout of the DST and the boreholes and instrumentation used to monitor the THCM processes in the rock of associated drifts. Section 2 presents an analysis of temperature data for the test through the end of May 1998. Sections 3 and 4 present results of electrical resistance tomography and neutron logging measurements, respectively. These two sets of measurements are designed to determine the movement of moisture in the test. Results of a series of geochemical measurements made on gas and water samples are presented in Section 5. The purpose of these measurements is to monitor the chemical processes occurring in the DST. Section 6 presents results of thermohydrologic modeling analysis of the test, and Section 7 presents data collected via the laboratory testing for characterization of the hydrologic properties of the rock forming the DST. A brief analysis of barometric pressure and humidity data collected through the end of May 1998 is discussed in Section 8, along with temperature data for the bulkhead. Finally, Section 9 presented an evaluation of sensors used in the DST.

Augmented Cross-Sectional Studies with Abbreviated Follow-up for Estimating HIV Incidence

OpenAIRE

Claggett, B.; Lagakos, S.W.; Wang, R.

2011-01-01

Cross-sectional HIV incidence estimation based on a sensitive and less-sensitive test offers great advantages over the traditional cohort study. However, its use has been limited due to concerns about the false negative rate of the less-sensitive test, reflecting the phenomenon that some subjects may remain negative permanently on the less-sensitive test. Wang and Lagakos (2010) propose an augmented cross-sectional design which provides one way to estimate the size of the infected population ...

Optimization of specimen preparation of thin cell section for AFM observation

Energy Technology Data Exchange (ETDEWEB)

Li Xinhui [Nanobiology Laboratory, Bio-X Life Science Research Center, School of Life Science and Biotechnology, Shanghai Jiao Tong University, 800 Dongchuan Road, Minhang District, Shanghai 200240 (China); Ji Tong [Department of Oral and Maxillofacial Surgery, School of Stomatology, Affiliated Ninth People' s Hospital, Medical School, Shanghai Jiao Tong University, Shanghai 200011 (China); Hu Jun [Nanobiology Laboratory, Bio-X Life Science Research Center, School of Life Science and Biotechnology, Shanghai Jiao Tong University, 800 Dongchuan Road, Minhang District, Shanghai 200240 (China); Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); Sun Jielin [Nanobiology Laboratory, Bio-X Life Science Research Center, School of Life Science and Biotechnology, Shanghai Jiao Tong University, 800 Dongchuan Road, Minhang District, Shanghai 200240 (China)], E-mail: jlsun@sjtu.edu.cn

2008-08-15

High resolution imaging of intracellular structures of ultrathin cell section samples is critical to the performance of precise manipulation by atomic force microscopy (AFM). Here, we test the effect of multiple factors during section sample preparation on the quality of the AFM image. These factors include the embedding materials, the annealing process of the specimen block, section thickness, and section side. We found that neither the embedding materials nor the temperature and speed of the annealing process has any effect on AFM image resolution. However, the section thickness and section side significantly affect the surface topography and AFM image resolution. By systematically testing the image quality of both sides of cell sections over a wide range of thickness (40-1000 nm), we found that the best resolution was obtained with upper-side sections approximately 50-100 nm thick. With these samples, we could observe precise structure details of the cell, including its membrane, nucleoli, and other organelles. Similar results were obtained for other cell types, including Tca8113, C6, and ECV-304. In brief, by optimizing the condition of ultrathin cell section preparation, we were able to obtain high resolution intracellular AFM images, which provide an essential basis for further AFM manipulation.

The safe motherhood referral system to reduce cesarean sections and perinatal mortality - a cross-sectional study [1995-2006

Directory of Open Access Journals (Sweden)

Rudge Marilza VC

2011-11-01

Full Text Available Abstract Background In 2000, the eight Millennium Development Goals (MDGs set targets for reducing child mortality and improving maternal health by 2015. Objective To evaluate the results of a new education and referral system for antenatal/intrapartum care as a strategy to reduce the rates of Cesarean sections (C-sections and maternal/perinatal mortality. Methods Design: Cross-sectional study. Setting: Department of Gynecology and Obstetrics, Botucatu Medical School, Sao Paulo State University/UNESP, Brazil. Population: 27,387 delivering women and 27,827 offspring. Data collection: maternal and perinatal data between 1995 and 2006 at the major level III and level II hospitals in Botucatu, Brazil following initiation of a safe motherhood education and referral system. Main outcome measures: Yearly rates of C-sections, maternal (/100,000 LB and perinatal (/1000 births mortality rates at both hospitals. Data analysis: Simple linear regression models were adjusted to estimate the referral system's annual effects on the total number of deliveries, C-section and perinatal mortality ratios in the two hospitals. The linear regression were assessed by residual analysis (Shapiro-Wilk test and the influence of possible conflicting observations was evaluated by a diagnostic test (Leverage, with p Results Over the time period evaluated, the overall C-section rate was 37.3%, there were 30 maternal deaths (maternal mortality ratio = 109.5/100,000 LB and 660 perinatal deaths (perinatal mortality rate = 23.7/1000 births. The C-section rate decreased from 46.5% to 23.4% at the level II hospital while remaining unchanged at the level III hospital. The perinatal mortality rate decreased from 9.71 to 1.66/1000 births and from 60.8 to 39.6/1000 births at the level II and level III hospital, respectively. Maternal mortality ratios were 16.3/100,000 LB and 185.1/100,000 LB at the level II and level III hospitals. There was a shift from direct to indirect causes of

Effect of evaporation section and condensation section length on thermal performance of flat plate heat pipe

International Nuclear Information System (INIS)

Wang Shuangfeng; Chen Jinjian; Hu Yanxin; Zhang Wei

2011-01-01

Flat plate heat pipes (FPHPs) are one of the available technologies to deal with the high density electronic cooling problem due to their high thermal conductivity, reliability, and low weight penalty. A series of experiments were performed to investigate the effect of evaporation and condensation length on thermal performance of flat plate heat pipes. In the experiments, the FPHP had heat transfer length of 255 mm and width of 25 mm, and pure water was used as the working fluid. The results show that comparing to vapor chamber, the FPHP could realize long-distance heat transfer; comparing to the traditional heat pipe, the FPHP has large area contact with heat sources; the thermal resistance decreased and the heat transfer limit increased with the increase of evaporation section length; the FPHP would dry out at a lower heating power with the increase of condensation section length, which indicated that the heat transfer limit decreased, but the evaporator temperature also decreased; when the condensation section length approached to evaporation section length, the FPHP had a better thermal performance. - Highlights: → A strip sintered FPHP is proposed and tested. → The total heat transfer length reaches 255 mm → The efficiency of heat transport reaches 94.4%. → When the condensation section length approached to evaporation section length, the FPHP has better overall performance.

On JALT 95: Curriculum and Evaluation. Proceedings of the JALT International Conference on Language Teaching/Learning (22nd, Nagoya, Japan, November 1995). Section Seven: Testing and Evaluation.

Science.gov (United States)

Brown, James Dean; And Others

This section contains conference papers on testing and evaluation in second language teaching. They include: "English Language Entrance Examinations in Japan: Problems and Solutions" (James Dean Brown); "Reliability and a Learner Style Questionnaire" (Dale T. Griffee); "Does It Work?" Evaluating Language Learning Tasks" (Rod Ellis); "Communicative…

The Alcohol Use Disorders Identification Test for Consumption (AUDIT-C is more useful than pre-existing laboratory tests for predicting hazardous drinking: a cross-sectional study

Directory of Open Access Journals (Sweden)

Hideki Fujii

2016-05-01

Full Text Available Abstract Background It is important to screen for alcohol consumption and drinking customs in a standardized manner. The aim of this study was 1 to investigate whether the AUDIT score is useful for predicting hazardous drinking using optimal cutoff scores and 2 to use multivariate analysis to evaluate whether the AUDIT score was more useful than pre-existing laboratory tests for predicting hazardous drinking. Methods A cross-sectional study using the Alcohol Use Disorders Identification Test (AUDIT was conducted in 334 outpatients who consulted our internal medicine department. The patients completed self-reported questionnaires and underwent a diagnostic interview, physical examination, and laboratory testing. Results Forty (23 % male patients reported daily alcohol consumption ≥ 40 g, and 16 (10 % female patients reported consumption ≥ 20 g. The optimal cutoff values of hazardous drinking were calculated using a 10-fold cross validation, resulting in an optimal AUDIT score cutoff of 8.2, with a sensitivity of 95.5 %, specificity of 87.0 %, false positive rate of 13.0 %, false negative rate of 4.5 %, and area under the receiver operating characteristic curve of 0.97. Multivariate analysis revealed that the most popular short version of the AUDIT consisting solely of its three consumption items (AUDIT-C and patient sex were significantly associated with hazardous drinking. The aspartate transaminase (AST/alanine transaminase (ALT ratio and mean corpuscular volume (MCV were weakly significant. Conclusions This study showed that the AUDIT score and particularly the AUDIT-C score were more useful than the AST/ALT ratio and MCV for predicting hazardous drinking.

Timed function tests, motor function measure, and quantitative thigh muscle MRI in ambulant children with Duchenne muscular dystrophy: A cross-sectional analysis.

Science.gov (United States)

Schmidt, Simone; Hafner, Patricia; Klein, Andrea; Rubino-Nacht, Daniela; Gocheva, Vanya; Schroeder, Jonas; Naduvilekoot Devasia, Arjith; Zuesli, Stephanie; Bernert, Guenther; Laugel, Vincent; Bloetzer, Clemens; Steinlin, Maja; Capone, Andrea; Gloor, Monika; Tobler, Patrick; Haas, Tanja; Bieri, Oliver; Zumbrunn, Thomas; Fischer, Dirk; Bonati, Ulrike

2018-01-01

The development of new therapeutic agents for the treatment of Duchenne muscular dystrophy has put a focus on defining outcome measures most sensitive to capture treatment effects. This cross-sectional analysis investigates the relation between validated clinical assessments such as the 6-minute walk test, motor function measure and quantitative muscle MRI of thigh muscles in ambulant Duchenne muscular dystrophy patients, aged 6.5 to 10.8 years (mean 8.2, SD 1.1). Quantitative muscle MRI included the mean fat fraction using a 2-point Dixon technique, and transverse relaxation time (T2) measurements. All clinical assessments were highly significantly inter-correlated with p muscle MRI values significantly correlated with all clinical assessments with the extensors showing the strongest correlation. In contrast to the clinical assessments, quantitative muscle MRI values were highly significantly correlated with age. In conclusion, the motor function measure and timed function tests measure disease severity in a highly comparable fashion and all tests correlated with quantitative muscle MRI values quantifying fatty muscle degeneration. Copyright © 2017 Elsevier B.V. All rights reserved.

Testing of a JEF-1 based WIMS-D cross section library for migration area and k-infinity predictions for LWHCR lattices

International Nuclear Information System (INIS)

Pelloni, S.; Stepanek, J.

1987-01-01

The cell code WIMSD4 is used for the analysis of PROTEUS-LWHCR experiments. A library for this code which is based on the European evaluation JEF-1 was produced at EIR using the Los Alamos NJOY system with its module WIMSR and the Canadian management code WILMA. In general, this library delivered more accurate eigenvalues and reaction rates than the WIMS-Standard and WIMS81 libraries did in comparison to experimental values from PROTEUS-LWHCR Cores 1-3. However, large discrepancies (up to about 10%) occured between calculated migration areas (M 2 ). Additional investigations have been undertaken to clarify this problem, since theoretical M 2 -values are needed for deducing k-infinity in the experiments. This has been done in the context of calculations for a reference LWHCR test lattice. The following major reasons for these deviations were found. First, the self-scattering term in non-moderators (P 0 matrix) in the JEF-1 library was not transport corrected. Second, Standard and JEF-1 libraries use infinite dilute cross sections for 238 U, whereas the WIMS81 library uses fully shielded cross sections. Third, the standard library uses the 'row' formula for the transport correction, whereas the 'inflow' formula is applied in the case of JEF-1 and WIMS81 libraries. Lastly, oxygen and 238 U scattering cross sections in the fast energy range are smaller in the case of the WIMS81 library. Differences in calculated k-infinity values between the currently used library and WIMS81 (up to 3%) come (in order of importance for the reference LWHCR lattice) mainly from resonance cross sections for 240 Pu capture, 238 U capture and 239 Pu fission. Recommendations have been made for generating a new JEF-1 library using updated versions of WIMSR and WILMA. (author)

Audit of HIV counselling and testing services among primary healthcare facilities in Cameroon: a protocol for a multicentre national cross-sectional study.

Science.gov (United States)

Tianyi, Frank-Leonel; Tochie, Joel Noutakdie; Agbor, Valirie Ndip; Kadia, Benjamin Momo

2018-03-01

HIV testing is an invaluable entry point to prevention, care and treatment services for people living with HIV and AIDS. Poor adherence to recommended protocols and guidelines reduces the performance of rapid diagnostic tests, leading to misdiagnosis and poor estimation of HIV seroprevalence. This study seeks to evaluate the adherence of primary healthcare facilities in Cameroon to recommended HIV counselling and testing (HCT) procedures and the impact this may have on the reliability of HIV test results. This will be an analytical cross-sectional study involving primary healthcare facilities from all the 10 regions of Cameroon, selected by a multistaged random sampling of primary care facilities in each region. The study will last for 9 months. A structured questionnaire will be used to collect general information concerning the health facility, laboratory and other departments involved in the HCT process. The investigators will directly observe at least 10 HIV testing processes in each facility and fill out the checklist accordingly. Clearance has been obtained from the National Ethical Committee to carry out the study. Informed consent will be sought from the patients to observe the HIV testing process. The final study will be published in a peer-reviewed journal and the findings presented to health policy-makers and the general public. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

46 CFR 113.05-7 - Environmental tests.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Environmental tests. 113.05-7 Section 113.05-7 Shipping... SYSTEMS AND EQUIPMENT General Provisions § 113.05-7 Environmental tests. Communication, alarm system, control, and monitoring equipment must meet the environmental tests of— (a) Section 4-9-7, Table 9, of ABS...

46 CFR 162.050-37 - Vibration test.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Vibration test. 162.050-37 Section 162.050-37 Shipping...: SPECIFICATIONS AND APPROVAL ENGINEERING EQUIPMENT Pollution Prevention Equipment § 162.050-37 Vibration test. (a... paragraph (b) of this section. The test must be performed at an independent laboratory that has the...

9 CFR 113.33 - Mouse safety tests.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Mouse safety tests. 113.33 Section 113.33 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE... Procedures § 113.33 Mouse safety tests. One of the mouse safety tests provided in this section shall be...

HIV incidence in rural South Africa: comparison of estimates from longitudinal surveillance and cross-sectional cBED assay testing.

Directory of Open Access Journals (Sweden)

Till Bärnighausen

Full Text Available The BED IgG-Capture Enzyme Immunoassay (cBED assay, a test of recent HIV infection, has been used to estimate HIV incidence in cross-sectional HIV surveys. However, there has been concern that the assay overestimates HIV incidence to an unknown extent because it falsely classifies some individuals with non-recent HIV infections as recently infected. We used data from a longitudinal HIV surveillance in rural South Africa to measure the fraction of people with non-recent HIV infection who are falsely classified as recently HIV-infected by the cBED assay (the long-term false-positive ratio (FPR and compared cBED assay-based HIV incidence estimates to longitudinally measured HIV incidence.We measured the long-term FPR in individuals with two positive HIV tests (in the HIV surveillance, 2003-2006 more than 306 days apart (sample size n = 1,065. We implemented four different formulae to calculate HIV incidence using cBED assay testing (n = 11,755 and obtained confidence intervals (CIs by directly calculating the central 95(th percentile of incidence values. We observed 4,869 individuals over 7,685 person-years for longitudinal HIV incidence estimation. The long-term FPR was 0.0169 (95% CI 0.0100-0.0266. Using this FPR, the cross-sectional cBED-based HIV incidence estimates (per 100 people per year varied between 3.03 (95% CI 2.44-3.63 and 3.19 (95% CI 2.57-3.82, depending on the incidence formula. Using a long-term FPR of 0.0560 based on previous studies, HIV incidence estimates varied between 0.65 (95% CI 0.00-1.32 and 0.71 (95% CI 0.00-1.43. The longitudinally measured HIV incidence was 3.09 per 100 people per year (95% CI 2.69-3.52, after adjustment to the sex-age distribution of the sample used in cBED assay-based estimation.In a rural community in South Africa with high HIV prevalence, the long-term FPR of the cBED assay is substantially lower than previous estimates. The cBED assay performs well in HIV incidence estimation if the locally

Marine Hydrokinetic (MHK) Energy Conversion Research at UNH: From Fundamental Studies of Hydrofoil Sections, to Moderate Reynolds Number Turbine Tests in a Tow Tank, to Open Water Deployments at Tidal Energy Test Sites (Invited)

Science.gov (United States)

Wosnik, M.; Bachant, P.; Nedyalkov, I.; Rowell, M.; Dufresne, N.; Lyon, V.

2013-12-01

We report on research related to MHK turbines at the Center for Ocean Renewable Energy (CORE) at the University of New Hampshire (UNH). The research projects span varies scales, levels of complexity and environments - from fundamental studies of hydrofoil sections in a high speed water tunnel, to moderate Reynolds number turbine tests with inflow and wake studies in a large cross-section tow tank, to deployments of highly instrumented process models at tidal energy test sites in New England. A concerted effort over the past few years has brought significant new research infrastructure for marine hydrokinetic energy conversion online at UNH-CORE. It includes: a high-speed cavitation tunnel with independent control of velocity and pressure; a highly accurate tow mechanism, turbine test bed and wake traversing system for the 3.7m x 2.4m cross-section UNH tow tank; a 10.7m x 3.0m tidal energy test platform which can accommodate turbines up to 1.5m in diameter, for deployments at the UNH-CORE Tidal Energy Test Site in Great Bay Estuary, NH, a sheltered 'nursery site' suitable for intermediate scale tidal energy conversion device testing with peak currents typically above 2 m/s during each tidal cycle. Further, a large boundary layer wind tunnel, the new UNH Flow Physics Facility (W6.0m x H2.7m xL72m) is being used for detailed turbine wake studies, producing data and insight also applicable to MHK turbines in low Froude number deployments. Bi-directional hydrofoils, which perform equally well in either flow direction and could avoid the use of complex and maintenance-intensive yaw or blade pitch mechanisms, are being investigated theoretically, numerically and experimentally. For selected candidate shapes lift, drag, wake, and cavitation inception/desinence are measured. When combined with a cavitation inception model for MHK turbines, this information can be used to prescribe turbine design/operational parameters. Experiments were performed with a 1m diameter and 1m

Characterization and Modeling of Recycled Pavement Sections

Science.gov (United States)

2017-12-01

Because of its documented cost and environmental benefits, cold central plant recycling (CCPR) has attracted the interest of local and state departments of transportation. In 2015 two test pavement sections with CCPR as base layers were constructed a...

A Closer Look at Chinese EFL Learners' Test-Wiseness Strategies in Reading Test

Science.gov (United States)

Haiyan, Miao; Rilong, Liu

2016-01-01

This paper reports on an investigation into the relationship of test-takers' use of test-wiseness strategies to Chinese EFL learners' reading test performance. A test-wiseness questionnaire was administered immediately after the final achievement test to probe into how learners thought while completing the reading section of the test. It was found…

Evolution, calibration, and operational characteristics of the two-dimensional test section of the Langley 0.3-meter transonic cryogenic tunnel

Science.gov (United States)

Ladson, Charles L.; Ray, Edward J.

1987-01-01

Presented is a review of the development of the world's first cryogenic pressure tunnel, the Langley 0.3-Meter Transonic Cryogenic Tunnel (0.3-m TCT). Descriptions of the instrumentation, data acquisition systems, and physical features of the two-dimensional 8- by 24-in, (20.32 by 60.96 cm) and advanced 13- by 13-in (33.02 by 33.02 cm) adaptive-wall test-section inserts of the 0.3-m TCT are included. Basic tunnel-empty Mach number distributions, stagnation temperature distributions, and power requirements are included. The Mach number capability of the facility is from about 0.20 to 0.90. Stagnation pressure can be varied from about 80 to 327 K.

ASME section XI: rules for inservice inspection of nuclear power plants -an introspection

Energy Technology Data Exchange (ETDEWEB)

John, P K; Anto, Y; Mungikar, C P; Wagh, P M [Nuclear Power Corporation of India Ltd., Tarapur (India). Tarapur Atomic Power Station

1994-12-31

Section XI of the ASME BPV code is addressed to the examination, test and inspection requirements of the components of nuclear power plants (NPPs). Since its inception in 1970, this code section has undergone vast changes -probably the most among other ASME BPV code sections. Section XI is full fledged and lays down requirements with regard to all preservice inspections, inservice inspection, repair and replacement of components, tests of system etc. Tarapur Atomic Power Station (TAPS) has the distinction of being one of the earliest BWR type NPPs in the world that has an inservice inspection programme organised in line with the ASME section XI requirements. This paper summarises the experiences gained from time to time using this code section and a few suggestions to prospective users. An effort is also made to explain the philosophy of inservice inspection from ASME section XI point of view. 3 refs.

ASME section XI: rules for inservice inspection of nuclear power plants -an introspection

International Nuclear Information System (INIS)

John, P.K.; Anto, Y.; Mungikar, C.P.; Wagh, P.M.

1994-01-01

Section XI of the ASME BPV code is addressed to the examination, test and inspection requirements of the components of nuclear power plants (NPPs). Since its inception in 1970, this code section has undergone vast changes -probably the most among other ASME BPV code sections. Section XI is full fledged and lays down requirements with regard to all preservice inspections, inservice inspection, repair and replacement of components, tests of system etc. Tarapur Atomic Power Station (TAPS) has the distinction of being one of the earliest BWR type NPPs in the world that has an inservice inspection programme organised in line with the ASME section XI requirements. This paper summarises the experiences gained from time to time using this code section and a few suggestions to prospective users. An effort is also made to explain the philosophy of inservice inspection from ASME section XI point of view. 3 refs

Determination of Optimum Cross-section for Oran Highway Revetment

Science.gov (United States)

Velioglu, Deniz; Sogut, Erdinc; Guler, Isikhan

2017-04-01

Revetments are shore parallel, sloping coastal structures which are built to provide protection from the negative effects of the sea. The revetment mentioned in this study is located in the City of Oran, Algeria and is currently under construction. This study investigates the determination of the optimum revetment cross section for Oran highway, considering both the hydraulic stability of the revetment and economy. The existence of cliffs in the region and the settlement of the City of Oran created a necessity to re-align Oran highway; therefore, it was shifted towards the Gulf of Oran. Approximately 1 km of the highway is to be constructed on the Mediterranean Sea due to the new alignment. In order to protect the sea side of the road from the adverse effects of the sea, a revetment was designed. The proposed cross section had an armour layer composed of 23 tons of antifer units and regular placement of armour units was recommended. In order to check the hydraulic stability of the proposed section, physical model tests were performed in the laboratory of LEM (Laboratoire d'Etudes Maritimes) in Algeria, using the pre-determined design wave conditions. The physical model tests revealed that the trunk of the revetment was totaly damaged. Accordingly, the proposed section was found insufficient and certain modifications were required. The first modification was made in the arrangement of armour units, changing them from regular to irregular. After testing the new cross section, it was observed that the revetment was vulnerable to breaking wave attack due to the toe geometry and thus the toe of the revetment had to be re-shaped. Therefore, the second option was to reduce the toe elevation. It was observed that even though the revetment trunk was safe, the damage in the toe was not in acceptable limits. The new cross section was found insufficient and as the final option, the weight of the antifer units used in the armour layer was increased, the toe length of the

Jet cross sections in electron-positron annihilation

International Nuclear Information System (INIS)

Sharpe, S.R.

1983-08-01

There are few, if any, detailed tests of QCD at present. I disucss the problems associated with testing QCD and argue that the three jet angular distribution in electron-positron annihilation is a good quantity to use because it minimizes the sensitivity to nonperturbative effects and provides a test of the detailed structure of QCD. However, for such a test to be possible, the perturbation expansion must be well behaved. I present a calculation of the perturbative corrections using two different generalizations of the Sterman-Weinberg two-jet cross section. I argue that because of the uncertainties in our understanding of hadronization it is necessary that the corrections to both these cross sections be small. In presenting the results I use the recent proof of Mukti and Sterman that all the logarithms can be resummed. I find that at Z-factory energies there is a substantial region of parameters defining the jets for which the correction is small, but that there is no such region at PEP/PETRA energies. This problem at PEP/PETRA energies is made worse by the results of a study of the effects of hadronization. Using a simple model I find very significant effects at PEP/PETRA energies that would make a test difficult. These effects do not, however, present problems at Z-factory energies. I conclude that, even if there are further theoretical advances, testing QCD at PEP/PETRA energies using the three-jet angular distribution will be very difficult. However, this distribution can be used to test QCD in a detailed way at Z-factory energies. The corrected results, furthermore, show a systematic difference from the lowest order result that may be measurable at Z-factory energies. If this effect could be measured it would provide a yet more detailed test of QCD, testing, for example, the three gluon coupling. 66 references

Unit root tests for cross-sectionally dependent panels : The influence of observed factors

NARCIS (Netherlands)

Becheri, I.G.; Drost, F.C.; van den Akker, R.

This paper considers a heterogeneous panel unit root model with cross-sectional dependence generated by a factor structure—the factor common to all units being an observed covariate. The model is shown to be Locally Asymptotically Mixed Normal (LAMN), with the random part of the limiting Fisher

SHAMSI, 48 group cross-section library for fusion nucleonics analysis

International Nuclear Information System (INIS)

Ponti, C.; Abbas, Tayyab.

1982-01-01

A P 3 48 group coupled neutron gamma-ray (34 N - 14 G) cross-section library is produced and validated for neutronic studies in fusion reactor blanket/shield. This report describes the library content, the procedure adopted and the results of the calculations performed for testing the cross sections

Testing an ionization chamber with gaseous samples and measurements of the (n, alpha) reaction cross sections

CERN Document Server

Gledenov, Yu M; Salatskii, V I; Sedyshev, P V; Andrzejewski, J; Szalanski, P

1999-01-01

A new ionization chamber with gaseous samples (GIC) has been designed and tested on the thermal and resonance neutron beams of FLNP's neutron sources. The exposed gas volume serves as a target for neutrons. The obtained thermal cross sections for the sup 1 sup 7 O(n, alpha) sup 1 sup 4 C, sup 2 sup 1 Ne(n, alpha) sup 1 sup 8 O and sup 3 sup 6 Ar(n, alpha) sup 3 sup 3 S reactions are (233+-12) mb, (0.18+-0.09) mb and (5.43+-0.27) mb, respectively. These measurements have been performed on a pure beam of thermal neutrons from the high flux reactor IBR-2; and they demonstrated high efficiency and reliability of the method. Compared to samples on substrates, the application of gaseous samples makes the beam background essentially lower, and what is more important, the background component is totally absent due to the absence of Li and B microimpurities in gaseous samples while they do present in the samples on substrates. The method is also applicable to measurements with resonance neutrons. The recovery capabili...

Sexual behaviours, HIV testing, and the proportion of men at risk of transmitting and acquiring HIV in London, UK, 2000-13: a serial cross-sectional study.

Science.gov (United States)

Aghaizu, Adamma; Wayal, Sonali; Nardone, Anthony; Parsons, Victoria; Copas, Andrew; Mercey, Danielle; Hart, Graham; Gilson, Richard; Johnson, Anne M

2016-09-01

HIV incidence in men who have sex with men (MSM) in the UK has remained unchanged over the past decade despite increases in HIV testing and antiretroviral therapy (ART) coverage. In this study, we examine trends in sexual behaviours and HIV testing in MSM and explore the risk of transmitting and acquiring HIV. In this serial cross-sectional study, we obtained data from ten cross-sectional surveys done between 2000 and 2013, consisting of anonymous self-administered questionnaires and oral HIV antibody testing in MSM recruited in gay social venues in London, UK. Data were collected between October and January for all survey years up to 2008 and between February and August thereafter. All men older than 16 years were eligible to take part and fieldworkers attempted to approach all MSM in each venue and recorded refusal rates. Data were collected on demographic and sexual behavioural characteristics. We analysed trends over time using linear, logistic, and quantile regression. Of 13 861 questionnaires collected between 2000 and 2013, we excluded 1985 (124 had completed the survey previously or were heterosexual reporting no anal intercourse in the past year, and 1861 did not provide samples for antibody testing). Of the 11 876 eligible MSM recruited, 1512 (13%) were HIV positive, with no significant trend in HIV positivity over time. 35% (531 of 1505) of HIV-positive MSM had undiagnosed infection, which decreased non-linearly over time from 34% (45 of 131) to 24% (25 of 106; p=0·01), while recent HIV testing (ie, in the past year) increased from 26% (263 of 997) to 60% (467 of 777; pmove towards eradication of HIV. Public Health England. Copyright © 2016 Elsevier Ltd. All rights reserved.

Review of Section XI inservice inspection program effectiveness

International Nuclear Information System (INIS)

Cook, J.F. Sr.

1993-08-01

To evaluate the effectiveness of Section XI, Division 1, open-quotes Rules for Inservice Inspection of Nuclear Power Plant Components,close quotes of the American Society of Mechanical Engineers Boiler and Pressure Vessel Code, searches were performed of the Licensing Event Report and Nuclear Plant Reliability Data System computerized data bases, and a review was made of inservice inspection summary reports. It was found that the Section XI examinations and tests detect flaws in welds and plant components and result in subsequent corrective action. This study also shows that the format and topics of information provided in Section XI-prescribed inservice inspection summary reports vary widely

Review of Section XI inservice inspection program effectiveness

Energy Technology Data Exchange (ETDEWEB)

Cook, J.F. Sr.

1993-08-01

To evaluate the effectiveness of Section XI, Division 1, {open_quotes}Rules for Inservice Inspection of Nuclear Power Plant Components,{close_quotes} of the American Society of Mechanical Engineers Boiler and Pressure Vessel Code, searches were performed of the Licensing Event Report and Nuclear Plant Reliability Data System computerized data bases, and a review was made of inservice inspection summary reports. It was found that the Section XI examinations and tests detect flaws in welds and plant components and result in subsequent corrective action. This study also shows that the format and topics of information provided in Section XI-prescribed inservice inspection summary reports vary widely.

Organic research section. 1984 review and 1985 programs

International Nuclear Information System (INIS)

Glass, R.W.

1985-02-01

This report reviews the major activities and accomplishments of the Organic Research Section in 1984 and presents the 1985 work program. The three major areas of the Section's research work are non-metallic materials which includes applications and uses of plastics, petroleum products, coatings and elastomers; reactor waste management; and activity transport/decontamination of nuclear systems. In 1984, 50% of the Section's resources were used on studies in support of nuclear generation, 13% on reactor waste, and 37% on general activities and work in support of utilization, transmission and distribution, and thermal and hydraulic programs. About 60% of the section's work was supported by transfer and revenue funds as a result of urgent short-term work requirements which resulted in 68% of the work falling into the technical investigation, consulting and testing categories

Report on COTECH test procedure and characterization techniques

DEFF Research Database (Denmark)

Islam, Mohammad Aminul

that need to be attained for successful characterization of the planned demonstrators and it deals with the material characterization and prototype testing for the COTECH demonstrators. The summary of this report includes:  General description of COTECH industrial demonstrators  COTECH materials...... and material characterization techniques  Characterization techniques of the COTECH demonstrators  Functionality and lifecycle testing of the COTECH demonstrators Besides the general introduction and conclusion each section of the report is dedicated to the characterization techniques and test procedure.......Characterization techniques and test procedure requirements for innovative self-ligating dental brackets (EO) Section 5.Characterization techniques and test procedure requirements for smart diagnostic chips comprising a microfluidic channel system (GBO) Section 6.Characterization techniques and test procedure...

42 CFR 84.99 - Man tests; testing conditions; general requirements.

Science.gov (United States)

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Man tests; testing conditions; general requirements. 84.99 Section 84.99 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Self-Contained Breathing Apparatus § 84.99...

40 CFR 63.465 - Test methods.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Test methods. 63.465 Section 63.465... Halogenated Solvent Cleaning § 63.465 Test methods. (a) Except as provided in paragraphs (f) and (g) of this... Reference Method 307 in appendix A of this part. (b) Except as provided in paragraph (g) of this section for...

Jets and tests of qcd in e+ e- experiments

International Nuclear Information System (INIS)

Marshall, R.

This talk presents the current status of QCD tests using PETRA data. The paper is divided into three easy sections. The first section covers essentially qualitative comparisons using Q plots, thrust and P(T) distributions and energy or momentum flow. The second section describes the quantitative determination of (alpha sub s), and the third section covers the scalar-vector tests of QCD. (Copyright

Burnout experiments with 6 x 6, 8 x 8 and 7 x 7 rod bundle test sections using freon as model fluid

International Nuclear Information System (INIS)

Fulfs, H.; Katsaounis, A.; Minden, C.v.

1976-01-01

This paper reports on burnout experiments at staedy state condition using Freon12 as model fluid. The experiments were carried out with three test sections with 6 x 6, 8 x 8 and 7 x 7 rod bundles. The axial flux distribution of the rods is either constant or reactor like. The transformed measured points using STEVENS and BOURE scaling factors to equivalent water conditions respectively, were compared to the burnout correlation W3 using the reactor layout program DYNAMIT. The DYNAMIT code is a thermohydraulic lay-out reactor program without consideration of mixing flow between the subchannels. (orig.) [de

HBV and HCV test uptake and correlates among men who have sex with men in China: a nationwide cross-sectional online survey.

Science.gov (United States)

Fitzpatrick, Thomas; Pan, Stephen W; Tang, Weiming; Guo, Wilson; Tucker, Joseph D

2018-05-19

Hepatitis B virus (HBV) and hepatitis C virus (HCV) cause substantial morbidity and mortality in low-income and middle-income countries, including China. WHO guidelines recommend men who have sex with men (MSM) receive HBV and HCV screening. The purpose of this study was to determine the proportion of MSM in China who have HBV and HCV tested and identify correlates of test uptake. We conducted an online cross-sectional survey of young MSM in China. Respondents were asked to report previous HBV and HCV testing, sociodemographic information, sexual risk factors for hepatitis infection, other STI testing and primary care physician (PCP) status. Associations were analysed by logistic regression. 503 eligible MSM completed the survey. 41.0% (206/503) of MSM had HCV tested, and 38.2% (60/157) of MSM with no or uncertain HBV vaccination had HBV tested. In multivariate analysis, HCV testing was correlated with HBV testing (adjusted OR (aOR) 22.98, 95% CI 12.11 to 43.60), HIV testing (aOR 3.64, 95% CI 1.92 to 6.91), HIV-positive status (aOR 1.78, 95% CI 1.07 to 2.98) and having a PCP (aOR 2.40, 95% CI 1.44 to 3.98). Among MSM with no or uncertain HBV vaccination, HBV testing was correlated with HCV testing (aOR 80.85, 95% CI 20.80 to 314.33), HIV testing (aOR 5.26, 95% CI 1.81 to 15.28), HIV-positive status (aOR 3.00, 95% CI 1.22 to 7.37) and having a PCP (aOR 2.69, 95% CI 1.00 to 7.26). Our data suggest many young MSM in China have not received hepatitis testing. HCV testing rates were lower than those recently reported among MSM in Australia and the USA. The strong correlation between HBV and HCV testing suggests bundled testing interventions may be useful for MSM in China. Men with a PCP were more likely to have received hepatitis testing, consistent with literature demonstrating the importance of primary care in expanding access to testing. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No

Results from Evaluation of Proposed ASME AG-1 Section FI Metal Media Filters - 13063

Energy Technology Data Exchange (ETDEWEB)

Wilson, John A.; Giffin, Paxton K.; Parsons, Michael S.; Waggoner, Charles A. [Institute for Clean Energy Technology, Mississippi State University, 205 Research Blvd Starkville, MS 39759 (United States)

2013-07-01

High efficiency particulate air (HEPA) filtration technology is commonly used in Department of Energy (DOE) facilities that require control of radioactive particulate matter (PM) emissions due to treatment or management of radioactive materials. Although HEPA technology typically makes use of glass fiber media, metal and ceramic media filters are also capable of filtering efficiencies beyond the required 99.97%. Sintered metal fiber filters are good candidates for use in DOE facilities due to their resistance to corrosive environments and resilience at high temperature and elevated levels of relative humidity. Their strength can protect them from high differential pressure or pressure spikes and allow for back pulse cleaning, extending filter lifetime. Use of these filters has the potential to reduce the cost of filtration in DOE facilities due to life cycle cost savings. ASME AG-1 section FI has not been approved due to a lack of protocols and performance criteria for qualifying section FI filters. The Institute for Clean Energy Technology (ICET) with the aid of the FI project team has developed a Section FI test stand and test plan capable of assisting in the qualification ASME AG-1 section FI filters. Testing done at ICET using the FI test stand evaluates resistance to rated air flow, test aerosol penetration and resistance to heated air of the section FI filters. Data collected during this testing consists of temperature, relative humidity, differential pressure, flow rate, upstream particle concentration, and downstream particle concentration. (authors)

Evaluation of fission product neutron cross sections for JENDL

International Nuclear Information System (INIS)

1984-01-01

The recent activities on the evaluation of fission product (FP) neutron cross sections for JENDL (Japanese Evaluated Nuclear Data Library) are presented briefly. The integral test of JENDL-1 FP cross section file was performed using the CFRMF sample activation data and the STEK sample reactivity data, and the ratio of experiment to calculation was nearly constant for all the samples in the STEK measurement. Therefore, a tentative analysis was performed by applying the correction to the calculated scattering reactivity component. Better agreement with the experiment was obtained after applying this correction in most cases. The evaluation work on the JENDL-2 FP neutron cross sections is now in progress. The improvement of the data evaluation is presented in an itemized form. The JENDL-2 FP file will contain the evaluated data for 100 nuclides from Kr to Tb. The improvement and the future scope of the integral test for JENDL-2 FP data are summarized. (Asami, T.)

Cross-section requirements for reactor neutron flux measurements from the user's point of view

International Nuclear Information System (INIS)

Mas, P.; Lloret, R.

1978-01-01

The dosimetry of testing materials irradiations involves in practice a lot of problems: fluences measurements, knowledge of spectrum, choice of a convenient set of cross section, damage rate determination, transposition from testing reactor to power reactor. From those problems, we consider that a temporary recommandation concerning the differential cross section of some fluence detectors is to be done, and that it is necessary to dispose of more accessible benchmarks in order to correlate cross section and computer codes. (author)

A Testing Framework for Critical Space SW

Science.gov (United States)

Fernandez, Ignacio; Di Cerbo, Antonio; Dehnhardt, Erik; Massimo, Tipaldi; Brünjes, Bernhard

2015-09-01

This paper describes a testing framework for critical space SW named Technical Specification Validation Framework (TSVF). It provides a powerful and flexible means and can be used throughout the SW test activities (test case specification & implementation, test execution and test artifacts analysis). In particular, tests can be run in an automated and/or step-by-step mode. The TSVF framework is currently used for the validation of the Satellite Control Software (SCSW), which runs on the Meteosat Third Generation (MTG) satellite on-board computer. The main purpose of the SCSW is to control the spacecraft along with its various subsystems (AOCS, Payload, Electrical Power, Telemetry Tracking & Command, etc.) in a way that guarantees a high degree of flexibility and autonomy. The TSVF framework serves the challenging needs of the SCSW project, where a plan-driven approach has been combined with an agile process in order to produce preliminary SW versions (with a reduced scope of implemented functionality) in order to fulfill the stakeholders needs ([1]). The paper has been organised as follows. Section 2 gives an overview of the TSVF architecture and interfaces versus the test bench along with the technology used for its implementation. Section 3 describes the key elements of the XML based language for the test case implementation. Section 4 highlights all the benefits compared to conventional test environments requiring a manual test script development, whereas section 5 concludes the paper.

Tensile Strength of GFRP Reinforcing Bars with Hollow Section

Directory of Open Access Journals (Sweden)

Young-Jun You

2015-01-01

Full Text Available Fiber reinforced polymer (FRP has been proposed to replace steel as a reinforcing bar (rebar due to its high tensile strength and noncorrosive material properties. One obstacle in using FRP rebars is high price. Generally FRP is more expensive than conventional steel rebar. There are mainly two ways to reduce the cost. For example, one is making the price of each composition cost of FRP rebar (e.g., fibers, resin, etc. lower than steel rebar. Another is making an optimized design for cross section and reducing the material cost. The former approach is not easy because the steel price is very low in comparison with component materials of FRP. For the latter approach, the cost could be cut down by reducing the material cost. Therefore, an idea of making hollow section over the cross section of FRP rebar was proposed in this study by optimizing the cross section design with acceptable tensile performance in comparison with steel rebar. In this study, glass reinforced polymer (GFRP rebars with hollow section and 19 mm of outer diameter were manufactured and tested to evaluate the tensile performance in accordance with the hollowness ratio. From the test results, it was observed that the tensile strength decreased almost linearly with increase of hollowness ratio and the elastic modulus decreased nonlinearly.

Get Tested for HIV

Science.gov (United States)

... AIDS: What is HIV/AIDS? Women and HIV/AIDS Next section ... Tested? Why do I need to get tested for HIV? The only way to know if you have HIV is to get tested. Many people with HIV don’t have any symptoms. In the United States, about 1 in 7 ...

9 CFR 113.38 - Guinea pig safety test.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Guinea pig safety test. 113.38 Section... Standard Procedures § 113.38 Guinea pig safety test. The guinea pig safety test provided in this section... be injected either intramuscularly or subcutaneously into each of two guinea pigs and the animals...

Patient self-report section of the ASES questionnaire: a Spanish validation study using classical test theory and the Rasch model.

Science.gov (United States)

Vrotsou, Kalliopi; Cuéllar, Ricardo; Silió, Félix; Rodriguez, Miguel Ángel; Garay, Daniel; Busto, Gorka; Trancho, Ziortza; Escobar, Antonio

2016-10-18

The aim of the current study was to validate the self-report section of the American Shoulder and Elbow Surgeons questionnaire (ASES-p) into Spanish. Shoulder pathology patients were recruited and followed up to 6 months post treatment. The ASES-p, Constant, SF-36 and Barthel scales were filled-in pre and post treatment. Reliability was tested with Cronbach's alpha, convergent validity with Spearman's correlations coefficients. Confirmatory factor analysis (CFA) and the Rasch model were implemented for assessing structural validity and unidimensionality of the scale. Models with and without the pain item were considered. Responsiveness to change was explored via standardised effect sizes. Results were acceptable for both tested models. Cronbach's alpha was 0.91, total scale correlations with Constant and physical SF-36 dimensions were >0.50. Factor loadings for CFA were >0.40. The Rasch model confirmed unidimensionality of the scale, even though item 10 "do usual sport" was suggested as non-informative. Finally, patients with improved post treatment shoulder function and those receiving surgery had higher standardised effect sizes. The adapted Spanish ASES-p version is a valid and reliable tool for shoulder evaluation and its unidimensionality is supported by the data.

"Full-Scale Testing of Pavement Response"

DEFF Research Database (Denmark)

Ullidtz, Per; Ekdahl, Peter

1998-01-01

Three pavement sections in southern Sweden were instrumented in late 1991. Each section have instruments for measuring the strain at the bottom of the asphalt layer, vertical stress and strains in the subgrade and temperatures at different depths. The purpose was to evaluate different theoretical...... methods for determining stresses, strains and deflections in pavement structurers.Falling Weight Deflectometer (FWD) test were done on the test sections, and stresses and strains were measured both under FWD loading and under a rolling wheel load. Different back-analysis procedures were used to derive...

Activities of the Shielding Subcommittee of the ENDF/B Cross Section Evaluation Working Group

International Nuclear Information System (INIS)

Roussin, R.W.

1977-01-01

The Shielding Subcommittee of the Cross Section Evaluation Working Group (CSEWG) was established in 1967 to help ensure that the content of the ENDF/B cross section library was adequate for treating shielding problems. Early work of the subcommittee concentrated on devising formats for gamma-ray interaction and production data, as well as providing programs for testing the clerical and physics consistency of the files. The Radiation Shielding Information Center (RSIC) collaborated directly with evaluators on behalf of the National Neutron Cross Section Center (NNCSC) to begin testing and adding data sets to be fed into the official ENDF/B libraries. These efforts, which were sponsored by AEC-DRDT (now ERDA-DRDD), were augmented greatly through the Defense Nuclear Agency program of establishing a working cross section library in ENDF format. The effort concentrated on evaluation and testing of materials of interest to DNA programs and providing these for inclusion in the ENDF/B library. Shielding data testing efforts, as a part of the CSEWG Data Testing Program, are now also an integral part of the Shielding Subcommittee effort. Procedures for writing and approving the shielding benchmarks were devised by Shielding Subcommittee members. Data testing benchmark experiments have been documented and analyzed, and the most recent results for ENDF/B-IV are as reported as part of ENDF-230, ''Benchmark Testing of ENDF/B-IV.''

A global reference for caesarean section rates (C-Model): a multicountry cross-sectional study.

Science.gov (United States)

Souza, J P; Betran, A P; Dumont, A; de Mucio, B; Gibbs Pickens, C M; Deneux-Tharaux, C; Ortiz-Panozo, E; Sullivan, E; Ota, E; Togoobaatar, G; Carroli, G; Knight, H; Zhang, J; Cecatti, J G; Vogel, J P; Jayaratne, K; Leal, M C; Gissler, M; Morisaki, N; Lack, N; Oladapo, O T; Tunçalp, Ö; Lumbiganon, P; Mori, R; Quintana, S; Costa Passos, A D; Marcolin, A C; Zongo, A; Blondel, B; Hernández, B; Hogue, C J; Prunet, C; Landman, C; Ochir, C; Cuesta, C; Pileggi-Castro, C; Walker, D; Alves, D; Abalos, E; Moises, Ecd; Vieira, E M; Duarte, G; Perdona, G; Gurol-Urganci, I; Takahiko, K; Moscovici, L; Campodonico, L; Oliveira-Ciabati, L; Laopaiboon, M; Danansuriya, M; Nakamura-Pereira, M; Costa, M L; Torloni, M R; Kramer, M R; Borges, P; Olkhanud, P B; Pérez-Cuevas, R; Agampodi, S B; Mittal, S; Serruya, S; Bataglia, V; Li, Z; Temmerman, M; Gülmezoglu, A M

2016-02-01

To generate a global reference for caesarean section (CS) rates at health facilities. Cross-sectional study. Health facilities from 43 countries. Thirty eight thousand three hundred and twenty-four women giving birth from 22 countries for model building and 10,045,875 women giving birth from 43 countries for model testing. We hypothesised that mathematical models could determine the relationship between clinical-obstetric characteristics and CS. These models generated probabilities of CS that could be compared with the observed CS rates. We devised a three-step approach to generate the global benchmark of CS rates at health facilities: creation of a multi-country reference population, building mathematical models, and testing these models. Area under the ROC curves, diagnostic odds ratio, expected CS rate, observed CS rate. According to the different versions of the model, areas under the ROC curves suggested a good discriminatory capacity of C-Model, with summary estimates ranging from 0.832 to 0.844. The C-Model was able to generate expected CS rates adjusted for the case-mix of the obstetric population. We have also prepared an e-calculator to facilitate use of C-Model (www.who.int/reproductivehealth/publications/maternal_perinatal_health/c-model/en/). This article describes the development of a global reference for CS rates. Based on maternal characteristics, this tool was able to generate an individualised expected CS rate for health facilities or groups of health facilities. With C-Model, obstetric teams, health system managers, health facilities, health insurance companies, and governments can produce a customised reference CS rate for assessing use (and overuse) of CS. The C-Model provides a customized benchmark for caesarean section rates in health facilities and systems. © 2015 World Health Organization; licensed by John Wiley & Sons Ltd on behalf of Royal College of Obstetricians and Gynaecologists.

Pump testing - Comparison of factory vs. field test of centrifugal pumps

International Nuclear Information System (INIS)

Fehlau, R.

1992-01-01

Testing of pumps in situ, i.e., as installed in a system, will typically yield somewhat different performance results from the original manufacturer's factory test. This paper discusses some of the reasons for these variations. It shows that the factory test curves can be used for evaluation of initial acceptance tests but not for reference in normal inservice testing (IST). This is the basis for reference values used in American Society of Mechanical Engineers (ASME) Section 11 specifications and the revised ASME Code 1990

Youssef’s Syndrome following Cesarean Section

Directory of Open Access Journals (Sweden)

Ozer Birge

2015-01-01

Full Text Available Youssef’s syndrome is characterized by cyclic hematuria (menouria, absence of vaginal bleeding (amenorrhea, and urinary incontinence due to vesicouterine fistula (VUF, the least common of the urogynecological fistulas. Youssef’s syndrome has a variable clinical presentation. A vesicouterine fistula is an abnormal pathway between the bladder and the uterus. The most common cause is lower segment Cesarean section. Conservative treatment may be appropriate in some cases, but surgery is the definitive treatment. Vesicouterine fistula should be suspected in cases presenting with urinary incontinence even years after Cesarean section. Diagnostic tests as well as necessary appropriate surgery should be performed on cases with suspected vesicouterine fistula. We present a 40-year-old multiparous woman with vesicouterine fistula after primary Cesarean section; she presented with urinary incontinence, hematuria, and amenorrhea 1 year after the birth. Here, we discuss our case with the help of previously published studies found in the literature.

Get Tested for Cervical Cancer

Science.gov (United States)

... Print This Topic En español Get Tested for Cervical Cancer Browse Sections The Basics Overview Cervical Cancer Cervical ... Cervical Cancer 1 of 5 sections The Basics: Cervical Cancer What is cervical cancer? Cervical cancer is cancer ...

Safety measures for integrity test apparatus for IS process. Sulfuric acid decomposition section

International Nuclear Information System (INIS)

Noguchi, Hiroki; Kubo, Shinji; Iwatsuki, Jin; Onuki, Kaoru

2013-07-01

Hazardous substances such as sulfuric acid, sulfur dioxide and hydrogen iodide acid are employed in thermochemical Iodine-Sulfur (IS) process. It is necessary to take safety measure against workers and external environments to study experimentally on IS process. Presently we have been conducting to verify the soundness of main components made of engineering material in actual corrosive condition. An integrity test apparatus for the components of sulfuric acid decomposition was set up. We will use the hazardous substances such as sulfuric acid and sulfur dioxide and perform the experiment in pressurized condition in this integrity test. Safety measures for the test apparatus, operation and abnormal situation were considered prior to starting the test. This report summarized the consideration results for the safety measures on the integrity test apparatus for the components of sulfuric acid decomposition. (author)

The use of semi-quantitative tests at Cesarean section delivery for the differentiation of canine fetal fluids from maternal urine on the basis of biochemical characteristics.

Science.gov (United States)

Balogh, Orsolya; Roch, Marie; Keller, Stefanie; Michel, Erika; Reichler, Iris M

2017-01-15

In dogs, there is no diagnostic test to identify and differentiate fetal fluids from maternal urine in the event that a clear-yellowish vulvar discharge is observed pre-whelping. The objective of this study was to find a test that could easily and accurately identify rupture of the fetal membranes preceding parturition. Maternal urine, and amniotic fluid (AMF) and allantoic fluid (ALF) from only one fetus per bitch, were collected intraoperatively during Cesarean section. Specific gravity (SG) was analyzed with a refractometer, whereas the presence of leukocytes, protein, glucose, ketones, bilirubin, urobilinogen, nitrite, erythrocyte/hemoglobin (Hb), and the pH were assessed using a urine dipstick (Combur-Test ® ). Combined calcium and magnesium (Ca/Mg) content were evaluated with the Total Hardness Test. The AmniSure test, which detects rupture of fetal membranes in women on the basis of the presence of human placental alpha microglobulin-1, was also performed on canine AMF, ALF, and urine. Data were analyzed using the Fisher's exact test, Wilcoxon signed-rank test, and Pearson's correlation. Sensitivity, specificity, and positive and negative likelihood ratios (LR) were calculated for parameters with significant difference between urine and both fetal fluids. Maternal urine had higher SG and lower leukocyte, protein, Hb, and Ca/Mg content than AMF and ALF. Glucose was more often present in AMF (n = 17) and ALF (n = 12) than in urine (n = 1), whereas ketone bodies were rarely detected in ALF compared with urine. Bilirubin content was higher in urine and ALF than in AMF. AMF pH was less variable and higher than the pH of ALF or urine. The AmniSure was negative in all samples tested. Sensitivity and specificity for SG and for the detection of leukocytes, protein, glucose, Hb, Ca/Mg, and glucose without ketones in urine and fetal fluids were between 42% to 100% and 65% to 100%, respectively. Best positive LR was achieved for the detection of glucose without ketones

Mantoux Tuberculin Skin Test

Centers for Disease Control (CDC) Podcasts

Learn how to evaluate people for latent TB infection with the Mantoux tuberculin skin test. This podcast includes sections on administering and reading the Mantoux tuberculin skin test, the standard method for detecting latent TB infection since the 1930s.

Tensile testing

CERN Document Server

2004-01-01

A complete guide to the uniaxial tensile test, the cornerstone test for determining the mechanical properties of materials: Learn ways to predict material behavior through tensile testing. Learn how to test metals, alloys, composites, ceramics, and plastics to determine strength, ductility and elastic/plastic deformation. A must for laboratory managers, technicians, materials and design engineers, and students involved with uniaxial tensile testing. Tensile Testing , Second Edition begins with an introduction and overview of the test, with clear explanations of how materials properties are determined from test results. Subsequent sections illustrate how knowledge gained through tensile tests, such as tension properties to predict the behavior (including strength, ductility, elastic or plastic deformation, tensile and yield strengths) have resulted in improvements in materals applications. The Second Edition is completely revised and updated. It includes expanded coverage throughout the volume on a variety of ...

Fatigue test results of straight pipe with flaws in inner surface

International Nuclear Information System (INIS)

Shibata, Katsuyuki; Oba, Toshihiro; Kawamura, Takaichi; Yokoyama, Norio; Miyazono, Shohachiro

1981-01-01

Fatigue and fracture tests of piping models with flaws in the inner surface were carried out to investigate the fatigue crack growth, coalescence of multiple cracks and fracture behavior. Two straight test pipes with and without weldment in the test section of SUS304L stainless steel were tested under almost the same test conditions. Three artificial defects were machined in the inner surface of the test section of the test pipes. The fatigue test were performed untill the cracks coalesced and grew through the thickness. Subsequently, a static load was imposed on test pipe which contained a large crack in the test section. The test results show that the fatigue crack growth is slower than that predicted by the method specified in the Section XI of ASME Boiler and Pressure Vessel Code, and that the test pipes can endure more than the static load of 3Sm without an unstable fracture. (author)

Cross section measurement and integral test for several activation reactions using T + d and thick-Li + d sources

International Nuclear Information System (INIS)

Dumais, J.R.; Tanaka, S.; Odano, N.; Iwasaki, S.; Sugiyama, K.

1988-01-01

Recent activities on the area of the cross section measurement for several activation reactions at Department of Nucl. Eng., Tohoku Univ. are described. The first subject is the cross section measurement for (n,2n) reaction on aluminum using the RTNS-II neutron source. Cross sections with rather small error band were obtained for the incident neutron energies from 14 to 14.7 MeV. The second one is the status of the program for the integral experiments on several reactions using the thick Li + d source at Tohoku Fast Neutron Lab. The experimental results showed the usefullness of the source as a tool for the cross section assessment. (author)

DEVELOPMENT OF AG-1 SECTION FI ON METAL MEDIA FILTERS - 9061

International Nuclear Information System (INIS)

Adamson, D.; Waggoner, C.A.

2008-01-01

Development of a metal media standard (FI) for ASME AG-1 (Code on Nuclear Air and Gas Treatment) has been under way for almost ten years. This paper will provide a brief history of the development process of this section and a detailed overview of its current content/status. There have been at least two points when dramatic changes have been made in the scope of the document due to feedback from the full Committee on Nuclear Air and Gas Treatment (CONAGT). Development of the proposed section has required resolving several difficult issues associated with scope; namely, filtering efficiency, operating conditions (media velocity, pressure drop, etc.), qualification testing, and quality control/acceptance testing. A proposed version of Section FI is currently undergoing final revisions prior to being submitted for balloting. The section covers metal media filters of filtering efficiencies ranging from medium (less than 99.97%) to high (99.97% and greater). Two different types of high efficiency filters are addressed; those units intended to be a direct replacement of Section FC fibrous glass HEPA filters and those that will be placed into newly designed systems capable of supporting greater static pressures and differential pressures across the filter elements. Direct replacements of FC HEPA filters in existing systems will be required to meet equivalent qualification and testing requirements to those contained in Section FC. A series of qualification and quality assurance test methods have been identified for the range of filtering efficiencies covered by this proposed standard. Performance characteristics of sintered metal powder vs. sintered metal fiber media are dramatically different with respect to parameters like differential pressures and rigidity of the media. Wide latitude will be allowed for owner specification of performance criteria for filtration units that will be placed into newly designed systems. Such allowances will permit use of the most

10 CFR 455.63 - Cost-effectiveness testing.

Science.gov (United States)

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Cost-effectiveness testing. 455.63 Section 455.63 Energy..., Hospitals, Units of Local Government, and Public Care Institutions § 455.63 Cost-effectiveness testing. (a... paragraph (a) of this section, if the State plan requires the cost effectiveness of an energy conservation...

24 CFR 882.123 - Conversion of Section 23 Units to Section 8 and Section 23 monitoring.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Conversion of Section 23 Units to... Applicability, Scope and Basic Policies § 882.123 Conversion of Section 23 Units to Section 8 and Section 23 monitoring. (a)-(d) [Reserved] (e) Section 23 policies for units planned for conversion on or before...

Radiographic testing at Lawrence Livermore National Laboratory

International Nuclear Information System (INIS)

Bossi, R.H.

1982-01-01

Radiographic testing is a nondestructive inspection technique which uses penetrating radiation. The Nondestructive Evaluation (NDE) Section at Lawrence Livermore National Laboratory has a broad spectrum of equipment and techniques for radiographic testing. These resources include low-energy vacuum systems, low- and mid-energy cabinet and cell radiographic systems, high-energy linear accelerators, portable x-ray machines and radioisotopes for radiographic inspections. For diagnostic testing the NDE Section also has real-time and flash radiographic equipment

Thin-section CT imaging that correlates with pulmonary function tests in obstructive airway disease

Energy Technology Data Exchange (ETDEWEB)

Arakawa, Hiroaki, E-mail: arakawa@dokkyomed.ac.jp [Department of Radiology, Dokkyo Medical University, 880 Kita-Kobayashi, Mibu, Tochigi 321-0293 (Japan); Fujimoto, Kiminori [Department of Radiology, Kurume University School of Medicine (Japan); Fukushima, Yasutugu [Department of Pulmonary Medicine and Clinical Immunology, Dokkyo Medical University (Japan); Kaji, Yasushi [Department of Radiology, Dokkyo Medical University, 880 Kita-Kobayashi, Mibu, Tochigi 321-0293 (Japan)

2011-11-15

Purpose: The purpose of this study was to identify independent CT findings that correlated with pulmonary function tests (PFTs) in patients with obstructive airway diseases. Materials and methods: Sixty-eight patients with obstructive airway disease and 29 normal subjects (mean age, 52 years; 36 men and 61 women) underwent inspiratory and expiratory thin-section CT and PFTs. Patient with obvious emphysema was excluded. Two radiologists independently reviewed the images and semi-quantitatively evaluated lung attenuation (mosaic perfusion, air trapping) and airway abnormalities (extent and severity of bronchial wall thickening and bronchiectasis, bronchiolectasis or centrilobular nodules, mucous plugging). Univariate, multivariate and receiver operating characteristic (ROC) analyses were performed with CT findings and PFTs. Results: Forty-two patients showed obstructive PFTs, 26 symptomatic patients showed near-normal PFTs. On univariate analysis, air trapping and bronchial wall thickening showed highest correlation with obstructive PFTs such as FEV1.0/FVC, MMEF and FEF75 (r ranged from -0.712 to -0.782; p < 0.001), while mosaic perfusion and mucous plugging showed moderate correlation, and bronchiectasis, bronchiolectasis and nodules showed the least, but significant, correlation. Multiple logistic analyses revealed air trapping and bronchial wall thickening as the only significant independent determinants of obstructive PFTs. ROC analysis revealed the cut-off value of air trapping for obstructive PFTs to be one-third of whole lung (area under curve, 0.847). Conclusions: Our study confirmed air trapping and bronchial wall thickening are the most important observations when imaging obstructive PFTs. The cut-off value of air trapping for identifying obstructive PFTs was one-third of lung irrespective of inspiratory CT findings.

SPORT AND EXERCISE PHYSIOLOGY TESTING Volume one: Sport Testing Volume two: Exercise and Clinical Testing

Directory of Open Access Journals (Sweden)

Edward M. Winter

2007-03-01

Full Text Available DESCRIPTION The objective of the book is to discuss the theoretical and practical aspects of physiological testing in exercise and sports which is essential to evaluate and monitor developing exercise performance for athletes and public health, and improving quality of life for patients.A board of leading sport and exercise physiologists and scientists are gathered to discuss physiological assessments that have proven validity and reliability, both in sport and health relevant issues. Incidentally, it updates the reader about the current subjects of physiological exertion testing in both research and clinical procedures. Both volumes individually cover the increasing number of available research and review publications, and theoretical explanations are supported by practical examples. A step-by-step and/or checklist method is used in appropriate sections which make the guides more user-friendly than most. PURPOSE The first volume is designed to help readers develop an understanding of the essential concepts of sport specific testing whereas the second volume aims at making the exercise and clinical specific testing comprehensible, dealing with both technical terms and the theories underlying the importance of these tests. AUDIENCE As Guidelines books of the British Association of Sport and Exercise Sciences, it will be of interest to a wide range of students, researchers and practitioners in the sport and exercise disciplines whether they work in the laboratory or in the field. FEATURES The first volume features immediate practical requirements particularly in sport testing. It is composed of five parts with detailed sub-sections in all of them. The topics of the parts are: i general principles, ii methodological issues, iii general procedures, iv sport specific procedures, v special populations.The second volume is also presented in five parts, again with sub-sections in all of them, but considering the requirements in clinical and exercise

Study of the thermal and hydraulic phenomena occurring during power excursion on a heated test section; Etude des phenomenes thermiques et hydrauliques accompagnant une excursion rapide de puissance sur un canal chauffant

Energy Technology Data Exchange (ETDEWEB)

Nyer, M [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1969-07-01

The thermal and hydrodynamic phenomena occurring during a power excursion were studied in an out-of-pile loop with a water cooled channel at low pressure (1 to 4 atm. abs. ). Circular and rectangular test sections with electrically heated walls of two different thermal diffusivity materials(aluminium and stainless steel) were used. The rectangular test sections were 600 mm long, 35 mm wide and had a 2, 9 mm gap; they simulate two half plates of the M.T.R. fuel element. Natural or forced convection are possible in the test section; the water height above it can be varied from 2.8 to 8 meters and the maximum allowed pressure at its outlet is 4 atm. abs.The heating source is a series of lead batteries which is able to generate, for short periods of time, 85 volts and 25000 amperes; linear, square or exponential power rise versus time can be realized. A 14 channels tape recorder (0-10 000 Hz bandwidth; is used for the measurements of temperature (8/100 mm diameter thermocouple), pressure ('Statham' pressure transducers) and void fraction (X rays). More than 500 tests have been carried out. The influence of the initial water temperature, flow rate, pressure, water height on the water ejections, pressure variations and void fraction in the test section were studied. Tests with energies up to 3000 W/cm in 50 milliseconds were attempted. The energy above which the instabilities appear was determined. An interpretation of the observed phenomena and a simplified theoretical model are presented. [French] Les phenomenes thermiques et hydrodynamiques qui apparaissent au cours d'une excursion de puissance ont ete etudies sur un canal refroidi par de l'eau a basse pression situe sur une installation hors pile. On a utilise des sections d'essais de geometrie cylindrique ou parallipedique dont les parois chauffees par effet Joule sont constituees de materiaux de diffusivite calorifique differente (aluminium et acier inoxydable). La section d'essais parallipedique a 600 mm de long

14 CFR 33.51 - Operation test.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Operation test. 33.51 Section 33.51... STANDARDS: AIRCRAFT ENGINES Block Tests; Reciprocating Aircraft Engines § 33.51 Operation test. The operation test must include the testing found necessary by the Administrator to demonstrate backfire...

The 6-minute walk test, motor function measure and quantitative thigh muscle MRI in Becker muscular dystrophy: A cross-sectional study.

Science.gov (United States)

Fischer, Dirk; Hafner, Patricia; Rubino, Daniela; Schmid, Maurice; Neuhaus, Cornelia; Jung, Hans; Bieri, Oliver; Haas, Tanja; Gloor, Monika; Fischmann, Arne; Bonati, Ulrike

2016-07-01

Becker muscular dystrophy (BMD) has an incidence of 1 in 16 000 male births. This cross-sectional study investigated the relation between validated functional scores and quantitative MRI (qMRI) of thigh muscles in 20 ambulatory BMD patients, aged 18.3-60 years (mean 31.2; SD 11.1). Clinical assessments included the motor function measure (MFM) and its subscales, as well as timed function tests such as the 6-minute walk test (6MWT) and the timed 10-m run/walk test. Quantitative MRI of the thigh muscles included the mean fat fraction (MFF) using a 2-point Dixon (2-PD) technique, and transverse relaxation time (T2) measurements. The mean MFM value was 80.4%, SD 9.44 and the D1 subscore 54.5%, SD 19.9. The median 6MWT was 195m, IQR 160-330.2. The median 10-m run/walk test was 7.4 seconds, IQR 6.1-9.3. The mean fat fraction of the thigh muscles was 55.6%, SD 17.4%, mean T2 relaxation times of all muscles: 69.9 ms, SD 14.4. The flexors had the highest MFF and T2 relaxation times, followed by the extensors and the adductors. MFF and global T2 relaxation times were highly negatively correlated with the MFM total, D1-subscore and 6MWT, and positively correlated with the 10 m run/walk test time (p < 0.01). Age was not correlated with MFF, global T2 relaxation time or clinical assessments. Both MFF and T2 measures in the thigh muscle were well correlated with clinical function in BMD and may serve as a surrogate outcome measure in clinical trials. Copyright © 2016 Elsevier B.V. All rights reserved.

Concrete. Course in Carpentry. Workbook and Tests.

Science.gov (United States)

California State Dept. of Education, Sacramento. Bureau of Publications.

This workbook is one of a series of individually bound units of instruction for carpentry apprenticeship classes in a four-year apprenticeship program. It consists of two sections--the workbook section and a test section. The workbook section provides instructional materials on 10 topics: introduction to cement and concrete, specifications for…

Occupational Stress and Hypertension among Railway Loco Pilots and Section Controllers

Science.gov (United States)

Jayakumar, Devasigamoney

2017-01-01

Introduction: A cross-sectional study on occupational stress was conducted on loco pilots in 2008, in view of loco pilots being one of the high strain jobs in Indian Railways. Subsequently, a comparative cross-sectional study on occupational stress was conducted among section controllers in 2011, which is another high strain job of Indian Railways. Objective: The studies were conducted to analyze and compare occupational stress and hypertension. Setting and Design: A cross-sectional study on occupational stress and hypertension was conducted among 230 loco pilots in 2008, and subsequently, a comparative cross-sectional study was conducted among 82 section controllers in 2011. Materials and Methods: A closed end 24 item questionnaire on occupational stress was administered. Systolic blood pressure above 140 mmHg and diastolic blood pressure above 90 mmHg were considered as hypertension as per the VII Joint National Committee. Chi-square test and t-test were used for testing significance at P < 0.05. Results: The mean stress score was 8.56 in loco pilots and 7.32 in section controllers. The number of loco pilots with more than 12 stress factors was 49 (21.3%) and the number of section controllers with more than 12 stress factors was 7 (8.5%). The number employees with more than 12 stress factors in different categories of loco pilots were 30 (32%) in the goods category, 12 (12%) in the mail/passenger category, and 7 (19%) in the shunter category, and 3 (11%) in the supervisory category and 4 (7%) in the on-board category of section controllers. The prevalence of hypertension in loco pilots was 36.52% (84) and in the section controllers was 53.66% (44). The prevalence of hypertension in the category with more than 12 stress factors was 30.61% (15) in the loco pilots and 28.57% (2) in the section controllers. The prevalence of hypertension in the both the study groups were higher in the older age, with a family history of hypertension, and with a body mass index of

Occupational Stress and Hypertension among Railway Loco Pilots and Section Controllers.

Science.gov (United States)

Jayakumar, Devasigamoney

2017-01-01

A cross-sectional study on occupational stress was conducted on loco pilots in 2008, in view of loco pilots being one of the high strain jobs in Indian Railways. Subsequently, a comparative cross-sectional study on occupational stress was conducted among section controllers in 2011, which is another high strain job of Indian Railways. The studies were conducted to analyze and compare occupational stress and hypertension. A cross-sectional study on occupational stress and hypertension was conducted among 230 loco pilots in 2008, and subsequently, a comparative cross-sectional study was conducted among 82 section controllers in 2011. A closed end 24 item questionnaire on occupational stress was administered. Systolic blood pressure above 140 mmHg and diastolic blood pressure above 90 mmHg were considered as hypertension as per the VII Joint National Committee. Chi-square test and t -test were used for testing significance at P stress score was 8.56 in loco pilots and 7.32 in section controllers. The number of loco pilots with more than 12 stress factors was 49 (21.3%) and the number of section controllers with more than 12 stress factors was 7 (8.5%). The number employees with more than 12 stress factors in different categories of loco pilots were 30 (32%) in the goods category, 12 (12%) in the mail/passenger category, and 7 (19%) in the shunter category, and 3 (11%) in the supervisory category and 4 (7%) in the on-board category of section controllers. The prevalence of hypertension in loco pilots was 36.52% (84) and in the section controllers was 53.66% (44). The prevalence of hypertension in the category with more than 12 stress factors was 30.61% (15) in the loco pilots and 28.57% (2) in the section controllers. The prevalence of hypertension in the both the study groups were higher in the older age, with a family history of hypertension, and with a body mass index of more than 25 kg/m 2 . The mean occupational stress and employees with more than 12 stress

Technical advances in the sectioning of dental tissue and of on-section cross-linked collagen detection in mineralized teeth.

Science.gov (United States)

Singhrao, Sim K; Sloan, Alastair J; Smith, Emma L; Archer, Charles W

2010-08-01

Immunohistochemical detection of cross-linked fibrillar collagens in mineralized tissues is much desired for exploring the mechanisms of biomineralization in health and disease. Mineralized teeth are impossible to section when embedded in conventional media, thus limiting on-section characterization of matrix proteins by immunohistochemistry. We hypothesized that by using an especially formulated acrylic resin suitable for mineralized dental tissues, not only sectioning of teeth would be possible, but also our recently developed immunofluorescence labeling technique would be amenable to fully calcified tissues for characterization of dentinal fibrillar collagens, which remains elusive. The hypothesis was tested on fixed rodent teeth embedded in Technovit 9100 New. It was possible to cut thin (1 mum) sections of mineralized teeth, and immunofluorescence characterization of cross-linked type I fibrillar collagen was selected due to its abundance in dentine. Decalcified samples of teeth embedded in paraffin wax were also used to compare immunolabeling from either method using the same immunoreagents in equivalent concentrations. In the decalcified tissue sections, type I collagen labeling in the dentine along the tubules was "patchy" and the signal in the predentine was very weak. However, enhanced signal in mineralized samples with type I collagen was detected not only in the predentine but also at the limit between intertubular dentine, within the elements of the enamel organ and subgingival stroma. This report offers advances in sectioning mineralized dental tissues and allows the application of immunofluorescence not only for on-section protein detection but importantly for detecting cross-linked fibrous collagens in both soft and mineralized tissue sections.

[Fast neutron cross section measurements

International Nuclear Information System (INIS)

1991-01-01

In the 14 MeV Neutron Laboratory, we have continued the development of a facility that is now the only one of its kind in operation in the United States. We have refined the klystron bunching system described in last year's report to the point that 1.2 nanosecond pulses have been directly measured. We have tested the pulse shape discrimination capability of our primary NE 213 neutron detector. We have converted the RF sweeper section of the beamline to a frequency of 1 MHz to replace the function of the high voltage pulser described in last year's report which proved to be difficult to maintain and unreliable in its operation. We have also overcome several other significant experimental difficulties, including a major problem with a vacuum leak in the main accelerator column. We have completed additional testing to prove the remainder of the generation and measurement systems, but overcoming some of these experimental difficulties has delayed the start of actual data taking. We are now in a position to begin our first series of ring geometry elastic scattering measurements, and these will be underway before the end of the current contract year. As part of our longer term planning, we are continuing the conceptual analysis of several schemes to improve the intensity of our current pulsed beam. These include the provision of a duoplasmatron ion source and/or the provision of preacceleration bunching. Additional details are given later in this report. A series of measurements were carried out at the Tandem Dynamatron Facility involving the irradiation of a series of yttrium foils and the determination of activation cross sections using absolute counting techniques. The experimental work has been completed, and final analysis of the cross section data will be completed within several months

Hydraulic Testing of Polymer Matrix Composite 102mm Tube Section Technical Report

Science.gov (United States)

2018-04-01

official Department of the Army position, policy, or decision, unless so designated by other documentation. The citation in this report of the names...the test specimen bore to measure strain in the hoop direction. Axial location of the interior strain gages was in the center of the test specimen...material. Each interior hoop direction strain gage contained a three-wire set-up for ease of balancing the bridge. Each internal strain gage wiring

Crashworthiness Analysis and Evaluation of Fuselage Section with Sub-floor Composite Sinusoidal Specimens

Directory of Open Access Journals (Sweden)

H.L. Mou

Full Text Available Abstract Crashworthiness is one of the main concerns in civil aviation safety particularly with regard to the increasing ratio of carbon fiber reinforced plastic (CFRP in aircraft primary structures. In order to generate dates for model validations, the mechanical properties of T700/3234 were obtained by material performance tests, and energy-absorbing results were gained by quasi-static crushing tests of composite sinusoidal specimens. The correctness of composite material model and single-layer finite element model of composite sinusoidal specimens were verified based on the simulation results and test results that were in good agreement. A typical civil aircraft fuselage section with composite sinusoidal specimens under cargo floor was suggested. The crashworthiness of finite element model of fuselage section was assessed by simulating the vertical drop test subjected to 7 m/s impact velocity, and the influences of different thickness of sub-floor composite sinusoidal specimens on crashworthiness of fuselage section were also analyzed. The simulation results show that the established finite element model can accurately simulate the crushing process of composite sinusoidal specimens; the failure process of fuselage section is more stable, and the safety of occupants can be effectively improved because of the smaller peak accelerations that was limited to human tolerance, a critical thickness of sub-floor composite sinusoidal specimens can restrict the magnitude of acceleration peaks, which has certain reference values for enhancing crashworthiness capabilities of fuselage section and improving the survivability of passengers.

Project W-320 acceptance test report for AY-farm electrical distribution

International Nuclear Information System (INIS)

Bevins, R.R.

1998-01-01

This Acceptance Test Procedure (ATP) has been prepared to demonstrate that the AY-Farm Electrical Distribution System functions as required by the design criteria. This test is divided into three parts to support the planned construction schedule; Section 8 tests Mini-Power Pane AY102-PPI and the EES; Section 9 tests the SSS support systems; Section 10 tests the SSS and the Multi-Pak Group Control Panel. This test does not include the operation of end-use components (loads) supplied from the distribution system. Tests of the end-use components (loads) will be performed by other W-320 ATPs

9 CFR 113.2 - Testing aids.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Testing aids. 113.2 Section 113.2... Testing aids. To better ensure consistent and reproducible test results when Standard Requirement tests... Agriculture, may provide testing aids, when available, to licensees, permittees, and applicants for licenses...

14 CFR 33.89 - Operation test.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Operation test. 33.89 Section 33.89... STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.89 Operation test. (a) The operation test must include testing found necessary by the Administrator to demonstrate— (1) Starting, idling...

49 CFR 236.587 - Departure test.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Departure test. 236.587 Section 236.587..., Train Control and Cab Signal Systems Inspection and Tests; Locomotive § 236.587 Departure test. (a) The...: (1) Operation over track elements; (2) Operation over test circuit; (3) Use of portable test...

Optimization of Asphalt Mixture Design for the Louisiana ALF Test Sections

Science.gov (United States)

2018-05-01

This research presents an extensive study on the design and characterization of asphalt mixtures used in road pavements. Both mixture volumetrics and physical properties obtained from several laboratory tests were considered in optimizing the mixture...

Quantitative and quality test of cross section library ENDF/B-b2

International Nuclear Information System (INIS)

Zajac, R.; Necas, V.

2006-01-01

This article includes a test or in other words data verification of neutron ENDF/B-VIIb2 sub library. The first part consists from the process of preparation ACE files by NJOY 99.90. The starting point of data verification describes needed patches in NJOY 99.90, which are necessary to do for correctly production of ACE files. After the obtaining ACE files follow the test of all ACE files through GODIVA - input file for MCNP. GODIVA is high enrichment sphere of U-235, where every material is added as impurity. The aim of GODIVA test is to obtain a certainty if produced ACE files are able to run through MCNP. The second part of this article begins with choose of benchmarks from 'International Handbook of Evaluated Criticality Safety Benchmark Experiments, 2005'. From this source of criticality experiments were separated some benchmarks for quality verification of ACE files by MCNP (Authors)

A dissociative electron attachment cross-section estimator

International Nuclear Information System (INIS)

Munro, James J; Harrison, Stephen; Fujimoto, Milton M; Tennyson, Jonathan

2012-01-01

Dissociative electron attachment (DEA) is the major process where molecules are destroyed in low-energy plasmas. DEA cross sections are therefore important for a whole variety of applications but are both hard to measure or compute accurately. A method for estimating DEA cross sections based a simple resonance plus survival model is presented. Test results are presented for DEA of molecular oxygen and molecular chlorine, for which experimental measurements are available for comparison, and SiBr and SiBr 2 , for which no previous data is available. The estimator has been implemented as part of Quantemol-N expert system which uses the R-matrix method to predict resonance positions and widths.

Design and Testing of an Educational Water Tunnel

Science.gov (United States)

Kosaraju, Srinivas

2017-11-01

A new water tunnel is designed and tested for educational and research purposes at Northern Arizona University. The university currently owns an educational wind tunnel with a test section of 12in X 12in X 24in. However, due to limited size of test section and range of Reynolds numbers, its application is currently limited to very few experiments. In an effort to expand the educational and research capabilities, a student team is tasked to design, build and test a water tunnel as a Capstone Senior Design project. The water tunnel is designed to have a test section of 8in X 8in X 36in. and be able to test up to Re = 50E3. Multiple numerical models are used to optimize the flow field inside the test section before building the physical apparatus. The water tunnel is designed to accommodate multiple experiments for drag and lift studies. The built-in die system can deliver up to three different colors to study the streamlines and vortex shedding from the surfaces. During the first phase, a low discharge pump is used to achieve Re = 4E3 to test laminar flows. In the second phase, a high discharge pump will be used to achieve targeted Re = 50E3 to study turbulent flows.

Factors influencing the uptake of voluntary HIV counseling and testing in rural Ethiopia: a cross sectional study

Directory of Open Access Journals (Sweden)

Hailay D. Teklehaimanot

2016-03-01

Full Text Available Abstract Background Voluntary counseling and testing (VCT has been one of the key policy responses to the HIV/AIDS epidemic in Ethiopia. However, the utilization of VCT has been low in the rural areas of the country. Understanding factors influencing the utilization of VCT provides information for the design of context based appropriate strategies that aim to improve utilization. This study examined the effects of socio-demographic and behavioral factors, and health service characteristics on the uptake of VCT among rural adults in Ethiopian. Methods/design This study was designed as a cross sectional study. Data from 11,919 adults (6278 women aged 15–49 years and 5641 men aged 15–59 years residing in rural areas of Ethiopia who participated in a national health extension program evaluation were used for this study. The participants were selected from ten administrative regions using stratified multi-stage cluster sampling. Multivariate logistic regression analysis was performed accounting for factors associated with the use of VCT service. Results Overall, men (28 % were relatively more likely to get tested for HIV than women (23.7 % through VCT. Rural men and women who were young and better educated, who perceived having small risk of HIV infection, who had comprehensive knowledge, no stigmatization attitude and discussed about HIV/AIDS with their partner, and model-family were more likely to undergone VCT. Regional state was also strongly associated with VCT utilization in both men and women. Rural women who belonged to households with higher socio-economic status, non-farming occupation, female-headed household and located near health facility, and who visited health extension workers and participated in community conversation were more likely to use VCT. Among men, agrarian lifestyle was associated with VCT use. Conclusions Utilization of VCT in the rural communities is low, and socio-economic, behavioral and health service factors

10 CFR 26.65 - Pre-access drug and alcohol testing.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Pre-access drug and alcohol testing. 26.65 Section 26.65... § 26.65 Pre-access drug and alcohol testing. (a) Purpose. This section contains pre-access testing... days. If an individual has negative results from drug and alcohol tests that were conducted under the...

14 CFR 35.39 - Endurance test.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Endurance test. 35.39 Section 35.39... STANDARDS: PROPELLERS Tests and Inspections § 35.39 Endurance test. Endurance tests on the propeller system... propellers must be subjected to one of the following tests: (1) A 50-hour flight test in level flight or in...

Studies on Section XI ultrasonic repeatability

International Nuclear Information System (INIS)

Jamison, T.D.; McDearman, W.R.

1981-05-01

A block representative of a nuclear component has been welded containing intentional defects. Acoustic emission data taken during the welding correlate well with ultrasonic data. Repetitive ultrasonic examinations have been performed by skilled operators using a procedure based on that desribed in ASME Section XI. These examinations were performed by different examination teams using different ultrasonic equipment in such a manner that the effects on the repeatability of the ultrasonic test method caused by the operator and by the use of different equipment could be estimated. It was tentatively concluded that when considering a large number of inspections: (1) there is no significant difference in indication sizing between operators, and (2) there is a significant difference in amplitude and defect sizing when instruments having different, Code acceptable operating characteristics are used. It was determined that the Section XI sizing parameters follow a bivariate normal distribution. Data derived from ultrasonically and physically sizing indications in nuclear components during farication show that the Section XI technique tends to overestimate the size of the reflectors

ENDF/B-VII.1 Neutron Cross Section Data Testing with Critical Assembly Benchmarks and Reactor Experiments

Energy Technology Data Exchange (ETDEWEB)

Kahler, A.C.; Herman, M.; Kahler,A.C.; MacFarlane,R.E.; Mosteller,R.D.; Kiedrowski,B.C.; Frankle,S.C.; Chadwick,M.B.; McKnight,R.D.; Lell,R.M.; Palmiotti,G.; Hiruta,H.; Herman,M.; Arcilla,R.; Mughabghab,S.F.; Sublet,J.C.; Trkov,A.; Trumbull,T.H.; Dunn,M.

2011-12-01

The ENDF/B-VII.1 library is the latest revision to the United States Evaluated Nuclear Data File (ENDF). The ENDF library is currently in its seventh generation, with ENDF/B-VII.0 being released in 2006. This revision expands upon that library, including the addition of new evaluated files (was 393 neutron files previously, now 423 including replacement of elemental vanadium and zinc evaluations with isotopic evaluations) and extension or updating of many existing neutron data files. Complete details are provided in the companion paper [M. B. Chadwick et al., 'ENDF/B-VII.1 Nuclear Data for Science and Technology: Cross Sections, Covariances, Fission Product Yields and Decay Data,' Nuclear Data Sheets, 112, 2887 (2011)]. This paper focuses on how accurately application libraries may be expected to perform in criticality calculations with these data. Continuous energy cross section libraries, suitable for use with the MCNP Monte Carlo transport code, have been generated and applied to a suite of nearly one thousand critical benchmark assemblies defined in the International Criticality Safety Benchmark Evaluation Project's International Handbook of Evaluated Criticality Safety Benchmark Experiments. This suite covers uranium and plutonium fuel systems in a variety of forms such as metallic, oxide or solution, and under a variety of spectral conditions, including unmoderated (i.e., bare), metal reflected and water or other light element reflected. Assembly eigenvalues that were accurately predicted with ENDF/B-VII.0 cross sections such as unmoderated and uranium reflected {sup 235}U and {sup 239}Pu assemblies, HEU solution systems and LEU oxide lattice systems that mimic commercial PWR configurations continue to be accurately calculated with ENDF/B-VII.1 cross sections, and deficiencies in predicted eigenvalues for assemblies containing selected materials, including titanium, manganese, cadmium and tungsten are greatly reduced. Improvements are also

30 CFR 27.31 - Testing methods.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Testing methods. 27.31 Section 27.31 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS METHANE-MONITORING SYSTEMS Test Requirements § 27.31 Testing methods. A methane...

The total collision cross section in the glory region

International Nuclear Information System (INIS)

Biesen, J.J.H. van den.

1982-01-01

Chapter 1 presents a calculation of approximate total cross sections in the glory region from noble gas potentials. The relations between the main features of the total cross section and the properties of the potential to which these are sensitive are extensively investigated in chapter II. A beam apparatus has been developed, which allows for accurate measurements on the total cross section. All effects due to the finite angular and velocity resolution of the apparatus can be eliminated from the data to yield actual total cross sections as a function of the relative velocity. This facilitates a comparison to total cross sections predicted by potentials available in the literature. A brief description of the apparatus and of the data reduction is given in chapter III. The total cross section data obtained for various noble gas combinations are presented and analysed in chapter IV, where also a large number of potentials proposed in the literature is tested. In chapter V the quenching of the glories in the case of a non-spherical interaction is analysed. Subsequently, total cross section data for some atom-molecule systems are discussed. (Auth.)

40 CFR 94.108 - Test fuels.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Test fuels. 94.108 Section 94.108... EMISSIONS FROM MARINE COMPRESSION-IGNITION ENGINES Test Procedures § 94.108 Test fuels. (a) Distillate diesel test fuel. (1) The diesel fuels for testing Category 1 and Category 2 marine engines designed to...

Mechanosensitivity during lower extremity neurodynamic testing is diminished in individuals with Type 2 Diabetes Mellitus and peripheral neuropathy: a cross sectional study

Directory of Open Access Journals (Sweden)

Boyd Benjamin S

2010-08-01

Full Text Available Abstract Background Type 2 Diabetes Mellitus (T2DM and diabetic symmetrical polyneuropathy (DSP impact multiple modalities of sensation including light touch, temperature, position sense and vibration perception. No study to date has examined the mechanosensitivity of peripheral nerves during limb movement in this population. The objective was to determine the unique effects T2DM and DSP have on nerve mechanosensitivity in the lower extremity. Methods This cross-sectional study included 43 people with T2DM. Straight leg raise neurodynamic tests were performed with ankle plantar flexion (PF/SLR and dorsiflexion (DF/SLR. Hip flexion range of motion (ROM, lower extremity muscle activity and symptom profile, intensity and location were measured at rest, first onset of symptoms (P1 and maximally tolerated symptoms (P2. Results The addition of ankle dorsiflexion during SLR testing reduced the hip flexion ROM by 4.3° ± 6.5° at P1 and by 5.4° ± 4.9° at P2. Individuals in the T2DM group with signs of severe DSP (n = 9 had no difference in hip flexion ROM between PF/SLR and DF/SLR at P1 (1.4° ± 4.2°; paired t-test p = 0.34 or P2 (0.9° ± 2.5°; paired t-test p = 0.31. Movement induced muscle activity was absent during SLR with the exception of the tibialis anterior during DF/SLR testing. Increases in symptom intensity during SLR testing were similar for both PF/SLR and DF/SLR. The addition of ankle dorsiflexion induced more frequent posterior leg symptoms when taken to P2. Conclusions Consistent with previous recommendations in the literature, P1 is an appropriate test end point for SLR neurodynamic testing in people with T2DM. However, our findings suggest that people with T2DM and severe DSP have limited responses to SLR neurodynamic testing, and thus may be at risk for harm from nerve overstretch and the information gathered will be of limited clinical value.

Test quality

International Nuclear Information System (INIS)

Hartley, R.S.; Keller, A.E.

1992-01-01

Inservice testing of safety-related components at nuclear power plants is performed under the American Society of Mechanical Engineers Boiler and Pressure Vessel Code (the Code). Subsections IWP and IWV of Section 11 of the Code state test method and frequency requirements for pumps and valves, respectively. Tests vary greatly in quality and frequency. This paper explores the concept of test quality and its relationship with operational readiness and preventive maintenance. This paper also considers the frequencies of component testing. Test quality is related to a test's ability to detect degradation that can cause component failure. The quality of the test depends on several factors, including specific parameters measured, system or component conditions, and instrument accuracy. The quality of some currently required tests for check valves, motor-operated valves, and pumps is also discussed. Suggestions are made to improve test quality by measuring different parameters, testing valves under load, and testing positive displacement pumps at high pressure and centrifugal pumps at high flow rate conditions. These suggestions can help to improve the level of assurance of component operational readiness gained from testing

Partially populated catalogue of measured properties of field sections.

Science.gov (United States)

2014-10-01

This catalogue documents the construction, monitoring, and mixture information of 11 test sections: four in SH 15 in the north Amarillo, three in US 62 in Childress, and four in Loop 820 in Fort Worth.

Prevalence and Correlates of HIV Testing among Young People Enrolled in Non-Formal Education Centers in Urban Chiang Mai, Thailand: A Cross-Sectional Study.

Directory of Open Access Journals (Sweden)

Patou Masika Musumari

Full Text Available HIV testing is the gateway to HIV prevention, treatment, and care. Despite the established vulnerability of young Thai people to HIV infection, studies examining the prevalence and correlates of HIV testing among the general population of Thai youth are still very limited. This study investigates socio-demographic, behavioral, and psychosocial factors associated with HIV testing among young Thai people enrolled in Non-formal Education Centers (NFEC in urban Chiang Mai, Northern Thailand.This was a cross-sectional quantitative study conducted among young unmarried Thai youth--between the ages of 15 and 24--who were enrolled in NFEC in urban Chiang Mai. Multiple logistic regressions were used to identify correlates of "ever tested for HIV" among the sexually active participants.Of the 295 sexually active participants, 27.3% reported "ever tested for HIV;" 65.4% "did not consistently use condom;" and 61.7% "had at least 2 lifetime partners." We found that "self-efficacy" (AOR, 4.92; CI, 1.22-19.73; "perception that it is easy to find a location nearby to test for HIV" (AOR, 4.67; CI, 1.21-18.06; "having at least 2 lifetime sexual partners" (AOR, 2.05; CI, 1.09-3.85; and "ever been pregnant or made someone pregnant" (AOR, 4.06; CI, 2.69-9.15; were associated with increased odds of having ever been tested. On the other hand, "fear of HIV test results" (AOR, 0.21; CI, 0.08-0.57 was associated with lower odds of ever having been tested for HIV.The main finding is that a substantially high proportion of Thai youth is engaged in risky sexual behaviors--yet reports low rates of ever having been tested for HIV. This highlights an urgent need to develop appropriate interventions--based on the identified correlates of HIV testing. There is also an urgent need to enhance HIV testing and to promote safer sexual behaviors among young Thai people--particularly those who are out-of-school.

Prevalence and Correlates of HIV Testing among Young People Enrolled in Non-Formal Education Centers in Urban Chiang Mai, Thailand: A Cross-Sectional Study.

Science.gov (United States)

Musumari, Patou Masika; Tangmunkongvorakul, Arunrat; Srithanaviboonchai, Kriengkrai; Yungyuankul, Sawang; Techasrivichien, Teeranee; Suguimoto, S Pilar; Ono-Kihara, Masako; Kihara, Masahiro; Chariyalertsak, Suwat

2016-01-01

HIV testing is the gateway to HIV prevention, treatment, and care. Despite the established vulnerability of young Thai people to HIV infection, studies examining the prevalence and correlates of HIV testing among the general population of Thai youth are still very limited. This study investigates socio-demographic, behavioral, and psychosocial factors associated with HIV testing among young Thai people enrolled in Non-formal Education Centers (NFEC) in urban Chiang Mai, Northern Thailand. This was a cross-sectional quantitative study conducted among young unmarried Thai youth--between the ages of 15 and 24--who were enrolled in NFEC in urban Chiang Mai. Multiple logistic regressions were used to identify correlates of "ever tested for HIV" among the sexually active participants. Of the 295 sexually active participants, 27.3% reported "ever tested for HIV;" 65.4% "did not consistently use condom;" and 61.7% "had at least 2 lifetime partners." We found that "self-efficacy" (AOR, 4.92; CI, 1.22-19.73); "perception that it is easy to find a location nearby to test for HIV" (AOR, 4.67; CI, 1.21-18.06); "having at least 2 lifetime sexual partners" (AOR, 2.05; CI, 1.09-3.85); and "ever been pregnant or made someone pregnant" (AOR, 4.06; CI, 2.69-9.15); were associated with increased odds of having ever been tested. On the other hand, "fear of HIV test results" (AOR, 0.21; CI, 0.08-0.57) was associated with lower odds of ever having been tested for HIV. The main finding is that a substantially high proportion of Thai youth is engaged in risky sexual behaviors--yet reports low rates of ever having been tested for HIV. This highlights an urgent need to develop appropriate interventions--based on the identified correlates of HIV testing. There is also an urgent need to enhance HIV testing and to promote safer sexual behaviors among young Thai people--particularly those who are out-of-school.

Cesarean Sections

Science.gov (United States)

... birth after a C-section, called a VBAC ) Emergency C-Sections Some C-sections are unexpected emergency ... side to nurse or using the clutch (or football) hold can take the pressure off your abdomen. ...

Test Plan Addendum No. 1: Waste Isolation Pilot Plant bin-scale CH TRU waste tests

International Nuclear Information System (INIS)

Molecke, M.A.; Lappin, A.R.

1990-12-01

This document is the first major revision to the Test Plan: WIPP Bin-Scale CH TRU Waste Tests. Factors that make this revision necessary are described and justified in Section 1, and elaborated upon in Section 4. This addendum contains recommended estimates of, and details for: (1) The total separation of waste leaching/solubility tests from bin-scale gas tests, including preliminary details and quantities of leaching tests required for testing of Levels 1, 2, and 3 WIPP CH TRU wastes; (2) An initial description and quantification of bin-scale gas test Phase 0, added to provide a crucial tie to pretest waste characterization representatives and overall test statistical validation; (3) A revision to the number of test bins required for Phases 1 and 2 of the bin gas test program, and specification of the numbers of additional bin tests required for incorporating gas testing of Level 2 wastes into test Phase 3. Contingencies are stated for the total number of test bins required, both positive and negative, including the supporting assumptions, logic, and decision points. (4) Several other general test detail updates occurring since the Test Plan was approved and published in January, 1990. Possible impacts of recommended revisions included in this Addendum on WIPP site operations are called out and described. 56 refs., 12 tabs

30 CFR 33.34 - Drilling test.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Drilling test. 33.34 Section 33.34 Mineral... MINING PRODUCTS DUST COLLECTORS FOR USE IN CONNECTION WITH ROCK DRILLING IN COAL MINES Test Requirements § 33.34 Drilling test. (a) A drilling test shall consist of drilling a set of 10 test holes, without...

30 CFR 7.67 - Construction test.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Construction test. 7.67 Section 7.67 Mineral... MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Multiple-Shot Blasting Units § 7.67 Construction test. The constuction test is to be performed on the blasting unit subsequent to the output energy test of...

Cone penetrometer acceptance test report

Energy Technology Data Exchange (ETDEWEB)

Boechler, G.N.

1996-09-19

This Acceptance Test Report (ATR) documents the results of acceptance test procedure WHC-SD-WM-ATR-151. Included in this report is a summary of the tests, the results and issues, the signature and sign- off ATP pages, and a summarized table of the specification vs. ATP section that satisfied the specification.

40 CFR 1065.520 - Pre-test verification procedures and pre-test data collection.

Science.gov (United States)

2010-07-01

... corrective action does not resolve the deficiency, you may request to use the contaminated system as an... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Pre-test verification procedures and pre-test data collection. 1065.520 Section 1065.520 Protection of Environment ENVIRONMENTAL PROTECTION...

Test anxiety and self-esteem in senior high school students: a cross-sectional study.

Science.gov (United States)

Sarı, Seda Aybüke; Bilek, Günal; Çelik, Ekrem

2018-02-01

In this study, it is aimed to determine the level of test anxiety and self-esteem in the high school students preparing for the university exam in Bitlis, Turkey, and to investigate the effect of test anxiety on self-esteem. Seven-hundred and twenty-four high school students who were preparing for the university entrance examination in Bitlis participated in the study. A questionnaire which includes socio-demographic data form, Rosenberg Self-Esteem Scale and Revised Test Anxiety Scale was prepared as an e-questionnaire for the students to fill easily and uploaded to the Bitlis State Hospital's website. Schools were called and informed for the students to fill out the e-questionnaire on the Internet. The most important findings from our study are that gender is influential on test anxiety and self-esteem score and test anxiety level are negatively correlated. It was observed that female students had more test anxiety than male students and those who had higher self-esteem had less test anxiety. Consequently, our study shows that university entrance examination creates anxiety on students and reduces self-esteem, especially in female students.

A Cross-Sectional Evaluation of Student Achievement Using Standardized and Performance-Based Tests

Science.gov (United States)

Pinter, Brad; Matchock, Robert L.; Charles, Eric P.; Balch, William R.

2014-01-01

Three groups of undergraduates (42 senior graduating psychology majors, 27 first-year premajors taking introductory psychology, and 24 first-year, high-performing nonmajors taking introductory psychology) completed the Psychology Major Field Test (MFT) and a short-answer (SA) essay test on reasoning about core knowledge in psychology. Graduating…

Cost benefit and risk assessment for selected tank waste process testing alternatives

International Nuclear Information System (INIS)

Gasper, K.A.

1995-01-01

The US Department of Energy has established the Tank Waste Remediation System (TWRS) program to safely manage wastes currently stored in underground tank at the Hanford Site. A TWRS testing and development strategy was recently developed to define long-range TWRS testing plans. The testing and development strategy considered four alternatives. The primary variable in the alternatives is the level of pilot-scale testing involving actual waste. This study evaluates the cost benefit and risks associated with the four alternatives. Four types of risk were evaluated: programmatic schedule risk, process mishap risk, worker risk, and public health risk. The structure of this report is as follows: Section 1 introduces the report subject; Section 2 describes the test strategy alternative evaluation; Section 3 describes the approach used in this study to assess risk and cost benefit; Section 4 describes the assessment methodologies for costs and risks; Section 5 describes the bases and assumptions used to estimate the costs and risks; Section 6 presents the detailed costs and risks; and Section 7 describes the results of the cost benefit analysis and presents conclusions

30 CFR 33.31 - Test space.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Test space. 33.31 Section 33.31 Mineral... § 33.31 Test space. (a) Drilling tests shall be conducted in a test space formed by two curtains suspended across a mine opening in such a manner that the volume of the test space shall be approximately 2...

46 CFR 154.605 - Toughness test.

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Toughness test. 154.605 Section 154.605 Shipping COAST....605 Toughness test. (a) Each toughness test under §§ 154.610 through 154.625 must meet Subpart 54.05 of this chapter. (b) If subsize test specimens are used for the Charpy V-notch toughness test, the...

46 CFR 64.83 - Hydrostatic test.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Hydrostatic test. 64.83 Section 64.83 Shipping COAST... HANDLING SYSTEMS Periodic Inspections and Tests of MPTs § 64.83 Hydrostatic test. (a) The hydrostatic test..., the heating coil passing a hydrostatic test at a pressure of 200 psig or more or 50 percent or more...

49 CFR 178.338-16 - Inspection and testing.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Inspection and testing. 178.338-16 Section 178.338... PACKAGINGS Specifications for Containers for Motor Vehicle Transportation § 178.338-16 Inspection and testing... Section VIII of the ASME Code. The welder and the welding procedure must be qualified in accordance with...

14 CFR 33.83 - Vibration test.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Vibration test. 33.83 Section 33.83... STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.83 Vibration test. (a) Each engine... experience, analysis, and component test and shall address, as a minimum, blades, vanes, rotor discs, spacers...

30 CFR 282.23 - Testing Plan.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Testing Plan. 282.23 Section 282.23 Mineral... § 282.23 Testing Plan. All testing activities shall be conducted in accordance with a Testing Plan... detailed Mining Plan than is obtainable under an approved Delineation Plan, to prepare feasibility studies...

49 CFR 383.133 - Testing methods.

Science.gov (United States)

2010-10-01

... 49 Transportation 5 2010-10-01 2010-10-01 false Testing methods. 383.133 Section 383.133... STANDARDS; REQUIREMENTS AND PENALTIES Tests § 383.133 Testing methods. (a) All tests shall be constructed in... must be at least as stringent as the Federal standards. (c) States shall determine specific methods for...

Generation and Testing of the ENDF/B-VI Continuous-Energy Cross-Section Library for Use with Continuous-Energy Versions of KENO

International Nuclear Information System (INIS)

Goluoglu, Sedat; Dunn, Michael E.; Greene, Norman Maurice; Petrie Jr, Lester M.; Hollenbach, Daniel F.

2007-01-01

KENO V.a and KENO-VI are Monte Carlo codes that solve the multigroup form of the Boltzmann transport equation. These codes are part of the SCALE system of codes and are used for performing criticality calculations of systems with fissionable material. In general, continuous-energy Monte Carlo methods are preferred because such an approach avoids many of the assumptions inherent in the multigroup treatment. On the other hand, continuous-energy treatment is much more demanding in terms of computer storage space for data, memory requirements, and calculation speed. Continuous-energy versions of KENO V.a and KENO-VI have been created and are being extensively tested. Generation of ENDF/B-VI continuous-energy cross sections is explained, and the results of the validation and verification of the codes and the data are presented

16 CFR 1209.7 - Test procedures for smoldering combustion.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Test procedures for smoldering combustion. 1209.7 Section 1209.7 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION CONSUMER PRODUCT SAFETY... for smoldering combustion. This section provides the test method for determining smoldering combustion...

Summary report on parametric pressure propagation test T0127-1

International Nuclear Information System (INIS)

Fauske, H.K.

1993-06-01

This report presents the results of two ferrocyanide propagating reaction generated aerosol tests, conducted as a part of a series of tests directed by Westinghouse Hanford Company (WHC). The tests discussed in this document are designated as T0208-1 and T0209-1. The tests were carried out in a 49 L containment volume equipped with an aerosol filter housing. The test setup is described in Section 2.0. Each test used an ∼ 50 gm. sample of InFarm-1 bottom flow sheet material which was vacuum dried, screened through a 140 mesh sieve, and rehydrated to 1 wgt. % water content prior to testing. The test sample and reaction ignition method are described in Section 3.0. A special test protocol was defined and followed for the tests as described in Section 4.0 and Appendix B. Test results are discussed in Section 5.0. Both tests yielded a significant aerosol sample on the filter element. These filter elements and aerosol deposits have been sent to WHC for analysis, and any information as to the content or chemical composition of the trapped particulate material awaits the results of WHC efforts in this regard. The reaction propagation tests were conducted at 60 degrees C and 120 degrees C respectively. The average propagation velocities are consistent with other related observations

Homogenized group cross sections by Monte Carlo

International Nuclear Information System (INIS)

Van Der Marck, S. C.; Kuijper, J. C.; Oppe, J.

2006-01-01

Homogenized group cross sections play a large role in making reactor calculations efficient. Because of this significance, many codes exist that can calculate these cross sections based on certain assumptions. However, the application to the High Flux Reactor (HFR) in Petten, the Netherlands, the limitations of such codes imply that the core calculations would become less accurate when using homogenized group cross sections (HGCS). Therefore we developed a method to calculate HGCS based on a Monte Carlo program, for which we chose MCNP. The implementation involves an addition to MCNP, and a set of small executables to perform suitable averaging after the MCNP run(s) have completed. Here we briefly describe the details of the method, and we report on two tests we performed to show the accuracy of the method and its implementation. By now, this method is routinely used in preparation of the cycle to cycle core calculations for HFR. (authors)

Test Section Turbulence in the AEDC/VKF Supersonic/Hypersonic Wind Tunnels

Science.gov (United States)

1981-07-01

8 4.3 Ins t rumen ta t ion ....................................................... 18...Pressure Fluctuation Spectral Content in AEDC Tunnels A and B (Based on FY79 Pitot Probe), Af = 200 Hz...intensity, spatial distribution, and spectral content , has become increasingly important in the analysis of test data. The sector- supported model in the

Technical operations procedure for assembly and emplacement of the soil temperature test--test assembly

International Nuclear Information System (INIS)

Weber, A.P.

1978-01-01

A description is given of the plan for assembly, instrumentation, emplacement, and operational checkout of the soil temperature test assembly and dry well liner. The activities described cover all operations necessary to accomplish the receiving inspection, instrumentation and pre-construction handling of the dry well liner, plus all operations performed with the test article. Actual details of construction work are not covered by this procedure. Each part and/or section of this procedure is a separate function to be accomplished as required by the nature of the operation. The organization of the procedure is not intended to imply a special operational sequence or schedular requirement. Specific procedure operational sections include: receiving inspection; liner assembly operations; construction operations (by others); prepare shield plug; test article assembly and installation; and operational checkout

49 CFR 236.588 - Periodic test.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Periodic test. 236.588 Section 236.588..., Train Control and Cab Signal Systems Inspection and Tests; Locomotive § 236.588 Periodic test. Except as provided in § 236.586, periodic test of the automatic train stop, train control, or cab signal apparatus...

14 CFR 33.43 - Vibration test.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Vibration test. 33.43 Section 33.43... STANDARDS: AIRCRAFT ENGINES Block Tests; Reciprocating Aircraft Engines § 33.43 Vibration test. (a) Each... configuration of the propeller type which is used for the endurance test, and using, for other engines, the same...

14 CFR 33.49 - Endurance test.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Endurance test. 33.49 Section 33.49... STANDARDS: AIRCRAFT ENGINES Block Tests; Reciprocating Aircraft Engines § 33.49 Endurance test. (a) General. Each engine must be subjected to an endurance test that includes a total of 150 hours of operation...

12 CFR 228.23 - Investment test.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 3 2010-01-01 2010-01-01 false Investment test. 228.23 Section 228.23 Banks... COMMUNITY REINVESTMENT (REGULATION BB) Standards for Assessing Performance § 228.23 Investment test. (a) Scope of test. The investment test evaluates a bank's record of helping to meet the credit needs of its...

40 CFR 60.8 - Performance tests.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Performance tests. 60.8 Section 60.8... PERFORMANCE FOR NEW STATIONARY SOURCES General Provisions § 60.8 Performance tests. (a) Except as specified in... conduct performance test(s) and furnish the Administrator a written report of the results of such...

14 CFR 33.47 - Detonation test.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Detonation test. 33.47 Section 33.47 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Reciprocating Aircraft Engines § 33.47 Detonation test. Each engine...

47 CFR 2.1503 - Test environment.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Test environment. 2.1503 Section 2.1503 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL FREQUENCY ALLOCATIONS AND RADIO TREATY MATTERS; GENERAL... Radiobeacons (EPIRBs) General § 2.1503 Test environment. (a) Measurement sites. Radiated emission tests for...

Production and testing of the VITAMIN-B6 fine-group and the BUGLE-93 broad-group neutron/photon cross-section libraries derived from ENDF/B-VI nuclear data

International Nuclear Information System (INIS)

Ingersoll, D.T.; White, J.E.; Wright, R.Q.; Hunter, H.T.; Slater, C.O.; Greene, N.M.; MacFarlane, R.E.

1993-01-01

A new multigroup cross-section library based on ENDF/B-VI data has been produced and tested for light water reactor shielding and reactor pressure vessel dosimetry applications. The broad-group library is designated BUGLE-93. The processing methodology is consistent with ANSI/ANS 6.1.2, since the ENDF data were first processed into a fine-group, ''pseudo problem-independent'' format and then collapsed into the final broad-group format. The fine-group library is designated VITAMIN-B6. An extensive integral data testing effort was also performed. In general, results using the new data show significant improvements relative to earlier ENDF data

The impact of interpreted flow regimes during constant head injection tests on the estimated transmissivity from injection tests and difference flow logging

Energy Technology Data Exchange (ETDEWEB)

Hjerne, Calle; Ludvigsson, Jan-Erik; Harrstroem, Johan [Geosigma AB, Uppsala (Sweden)

2013-04-15

A large number of constant head injection tests were carried out in the site investigation at Forsmark using the Pipe String System, PSS3. During the original evaluation of the tests the dominating transient flow regimes during both the injection and recovery period were interpreted together with estimation of hydraulic parameters. The flow regimes represent different flow and boundary conditions during the tests. Different boreholes or borehole intervals may display different distributions of flow regimes. In some boreholes good agreement was obtained between the results of the injection tests and difference flow logging with Posiva flow log (PFL) but in other boreholes significant discrepancies were found. The main objective of this project is to study the correlation between transient flow regimes from the injection tests and other borehole features such as transmissivity, depth, geology, fracturing etc. Another subject studied is whether observed discrepancies between estimated transmissivity from difference flow logging and injection tests can be correlated to interpreted flow regimes. Finally, a detailed comparison between transient and stationary evaluation of transmissivity from the injection tests in relation to estimated transmissivity from PFL tests in corresponding sections is made. Results from previous injection tests in 5 m sections in boreholes KFM04, KFM08A and KFM10A were used. Only injection tests above the (test-specific) measurement limit regarding flow rate are included in the analyses. For all of these tests transient flow regimes were interpreted. In addition, results from difference flow logging in the corresponding 5 m test sections were used. Finally, geological data of fractures together with rock and fracture zone properties have been used in the correlations. Flow regimes interpreted from the injection period of the tests are generally used in the correlations but deviations between the interpreted flow regimes from the injection and

ENDF/B-VII.1 Neutron Cross Section Data Testing with Critical Assembly Benchmarks and Reactor Experiments

Energy Technology Data Exchange (ETDEWEB)

Kahler, A. [Los Alamos National Laboratory (LANL); Macfarlane, R E [Los Alamos National Laboratory (LANL); Mosteller, R D [Los Alamos National Laboratory (LANL); Kiedrowski, B C [Los Alamos National Laboratory (LANL); Frankle, S C [Los Alamos National Laboratory (LANL); Chadwick, M. B. [Los Alamos National Laboratory (LANL); Mcknight, R D [Argonne National Laboratory (ANL); Lell, R M [Argonne National Laboratory (ANL); Palmiotti, G [Idaho National Laboratory (INL); Hiruta, h [Idaho National Laboratory (INL); Herman, Micheal W [Brookhaven National Laboratory (BNL); Arcilla, r [Brookhaven National Laboratory (BNL); Mughabghab, S F [Brookhaven National Laboratory (BNL); Sublet, J C [Culham Science Center, Abington, UK; Trkov, A. [Jozef Stefan Institute, Slovenia; Trumbull, T H [Knolls Atomic Power Laboratory; Dunn, Michael E [ORNL

2011-01-01

The ENDF/B-VII.1 library is the latest revision to the United States' Evaluated Nuclear Data File (ENDF). The ENDF library is currently in its seventh generation, with ENDF/B-VII.0 being released in 2006. This revision expands upon that library, including the addition of new evaluated files (was 393 neutron files previously, now 423 including replacement of elemental vanadium and zinc evaluations with isotopic evaluations) and extension or updating of many existing neutron data files. Complete details are provided in the companion paper [1]. This paper focuses on how accurately application libraries may be expected to perform in criticality calculations with these data. Continuous energy cross section libraries, suitable for use with the MCNP Monte Carlo transport code, have been generated and applied to a suite of nearly one thousand critical benchmark assemblies defined in the International Criticality Safety Benchmark Evaluation Project's International Handbook of Evaluated Criticality Safety Benchmark Experiments. This suite covers uranium and plutonium fuel systems in a variety of forms such as metallic, oxide or solution, and under a variety of spectral conditions, including unmoderated (i.e., bare), metal reflected and water or other light element reflected. Assembly eigenvalues that were accurately predicted with ENDF/B-VII.0 cross sections such as unrnoderated and uranium reflected (235)U and (239)Pu assemblies, HEU solution systems and LEU oxide lattice systems that mimic commercial PWR configurations continue to be accurately calculated with ENDF/B-VII.1 cross sections, and deficiencies in predicted eigenvalues for assemblies containing selected materials, including titanium, manganese, cadmium and tungsten are greatly reduced. Improvements are also confirmed for selected actinide reaction rates such as (236)U; (238,242)Pu and (241,243)Am capture in fast systems. Other deficiencies, such as the overprediction of Pu solution system critical

Construction of the two-phase critical flow test facility

International Nuclear Information System (INIS)

Chung, C. H.; Chang, S. K.; Park, H. S.; Min, K. H.; Choi, N. H.; Kim, C. H.; Lee, S. H.; Kim, H. C.; Chang, M. H.

2002-03-01

The two-phase critical test loop facility has been constructed in the KAERI engineering laboratory for the simulation of small break loss of coolant accident entrained with non-condensible gas of SMART. The test facility can operate at 12 MPa of pressure and 0 to 60 C of sub-cooling with 0.5 kg/s of non- condensible gas injection into break flow, and simulate up to 20 mm of pipe break. Main components of the test facility were arranged such that the pressure vessel containing coolant, a test section simulating break and a suppression tank inter-connected with pipings were installed vertically. As quick opening valve opens, high pressure/temperature coolant flows through the test section forming critical two-phase flow into the suppression tank. The pressure vessel was connected to two high pressure N2 gas tanks through a control valve to control pressure in the pressure vessel. Another N2 gas tank was also connected to the test section for the non-condensible gas injection. The test facility operation was performed on computers supported with PLC systems installed in the control room, and test data such as temperature, break flow rate, pressure drop across test section, gas injection flow rate were all together gathered in the data acquisition system for further data analysis. This test facility was classified as a safety related high pressure gas facility in law. Thus the loop design documentation was reviewed, and inspected during construction of the test loop by the regulatory body. And the regulatory body issued permission for the operation of the test facility

40 CFR 60.1300 - What test methods must I use to stack test?

Science.gov (United States)

2010-07-01

... to the Administrator for approval under § 60.8(b) to use a reference method with minor changes in... 40 Protection of Environment 6 2010-07-01 2010-07-01 false What test methods must I use to stack test? 60.1300 Section 60.1300 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...

49 CFR 178.814 - Hydrostatic pressure test.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Hydrostatic pressure test. 178.814 Section 178.814... Testing of IBCs § 178.814 Hydrostatic pressure test. (a) General. The hydrostatic pressure test must be... preparation for the hydrostatic pressure test. For metal IBCs, the test must be carried out before the fitting...

30 CFR 7.46 - Impact test.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Impact test. 7.46 Section 7.46 Mineral... MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Battery Assemblies § 7.46 Impact test. (a) Test... individual cells. At the test temperature range of 65 °F -80 °F (18.3 °C-26.7 °C), apply a dynamic force of...

Post-test investigation result on the WWER-1000 fuel tested under severe accident conditions

International Nuclear Information System (INIS)

Goryachev, A.; Shtuckert, Yu.; Zwir, E.; Stupina, L.

1996-01-01

The model bundle of WWER-type were tested under SFD condition in the out-of-pile CORA installation. The objective of the test was to provide an information on the WWER-type fuel bundles behaviour under severe fuel damage accident conditions. Also it was assumed to compare the WWER-type bundle damage mechanisms with these experienced in the PWR-type bundle tests with aim to confirm a possibility to use the various code systems, worked our for PWR as applied to WWER. In order to ensure the possibility of the comparison of the calculated core degradation parameters with the real state of the tested bundle, some parameters have been measured on the bundle cross-sections under examination. Quantitative parameters of the bundle degradation have been evaluated by digital image processing of the bundle cross-sections. The obtained results are shown together with corresponding results obtained by the other participants of this investigation. (author). 3 refs, 13 figs

Test quality

International Nuclear Information System (INIS)

Hartley, R.S.; Keller, A.E.

1992-01-01

This document discusses inservice testing of safety-related components at nuclear power plants which is performed under the American Society of Mechanical Engineers Boiler and Pressure Vessel Code (the Code). Subsections IWP and IWV of Section XI of the Code state test method and frequency requirements for pumps and valves respectively. Tests vary greatly in quality and frequency. This paper explores the concept of test quality and its relationship with operational readiness and preventive maintenance. This paper also considers the frequencies of component testing. Test quality is related to a test's ability to detect degradation that can cause component failure. The quality of the test depends on several factors, including specific parameters measured, system or component conditions, and instrument accuracy. The quality of some currently required tests for check valves, motor-operated valves, and pumps is also discussed. Suggestions are made to improve test quality by measuring different parameters, testing valves under load, and testing positive displacement pumps at high pressure and centrifugal pumps at high flow rate conditions. These suggestions can help to improve the level of assurance of component operational readiness gained from testing

14 CFR 33.87 - Endurance test.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Endurance test. 33.87 Section 33.87... STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.87 Endurance test. (a) General. Each engine must be subjected to an endurance test that includes a total of at least 150 hours of operation...

Study of the thermal and hydraulic phenomena occurring during power excursion on a heated test section; Etude des phenomenes thermiques et hydrauliques accompagnant une excursion rapide de puissance sur un canal chauffant

Energy Technology Data Exchange (ETDEWEB)

Nyer, M. [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1969-07-01

The thermal and hydrodynamic phenomena occurring during a power excursion were studied in an out-of-pile loop with a water cooled channel at low pressure (1 to 4 atm. abs. ). Circular and rectangular test sections with electrically heated walls of two different thermal diffusivity materials(aluminium and stainless steel) were used. The rectangular test sections were 600 mm long, 35 mm wide and had a 2, 9 mm gap; they simulate two half plates of the M.T.R. fuel element. Natural or forced convection are possible in the test section; the water height above it can be varied from 2.8 to 8 meters and the maximum allowed pressure at its outlet is 4 atm. abs.The heating source is a series of lead batteries which is able to generate, for short periods of time, 85 volts and 25000 amperes; linear, square or exponential power rise versus time can be realized. A 14 channels tape recorder (0-10 000 Hz bandwidth; is used for the measurements of temperature (8/100 mm diameter thermocouple), pressure ('Statham' pressure transducers) and void fraction (X rays). More than 500 tests have been carried out. The influence of the initial water temperature, flow rate, pressure, water height on the water ejections, pressure variations and void fraction in the test section were studied. Tests with energies up to 3000 W/cm in 50 milliseconds were attempted. The energy above which the instabilities appear was determined. An interpretation of the observed phenomena and a simplified theoretical model are presented. [French] Les phenomenes thermiques et hydrodynamiques qui apparaissent au cours d'une excursion de puissance ont ete etudies sur un canal refroidi par de l'eau a basse pression situe sur une installation hors pile. On a utilise des sections d'essais de geometrie cylindrique ou parallipedique dont les parois chauffees par effet Joule sont constituees de materiaux de diffusivite calorifique differente (aluminium et acier inoxydable). La section d

Dosimetry and Calibration Section

International Nuclear Information System (INIS)

Otto, T.

1999-01-01

The Dosimetry and Calibration Section fulfils two tasks within CERN's Radiation Protection Group: the Individual Dosimetry Service monitors more than 5000 persons potentially exposed to ionizing radiation on the CERN sites, and the Calibration Laboratory verifies throughout the year, at regular intervals, over 1000 instruments, monitors, and electronic dosimeters used by RP Group. The establishment of a Quality Assurance System for the Individual Dosimetry Service, a requirement of the new Swiss Ordinance for personal dosimetry, put a considerable workload on the section. Together with an external consultant it was decided to identify and then describe the different 'processes' of the routine work performed in the dosimetry service. The resulting Quality Manual was submitted to the Federal Office for Public Health in Bern in autumn. The CERN Individual Dosimetry Service will eventually be officially endorsed after a successful technical test in March 1999. On the technical side, the introduction of an automatic development machine for gamma films was very successful. It processes the dosimetric films without an operator being present, and its built-in regeneration mechanism keeps the concentration of the processing chemicals at a constant level

Development and testing of the cooling coil cleaning end effector

International Nuclear Information System (INIS)

Johnson, K.I.; Mullen, O.D.; Powell, M.R.; Daly, D.S.; Engel, D.W.

1997-01-01

The Retrieval Process Development and Enhancement (KPD ampersand E) program has developed and tested an end effector to support the waste retrieval mission at the Idaho National Engineering and Environmental Laboratory (INEEL). The end effector was developed specifically to remove a sticky waste material from the cooling coils in the High Level Liquid Waste (HLLW) tank, and to vacuum up a sediment layer that has settled beneath the cooling coils. An extensive testing program was conducted in the hydraulic test bed (HTB) at the Pacific Northwest National Laboratory (PNNL) to evaluate the performance of the end effector under simulated in-tank conditions. A mock up of the cooling coils was installed in the test bed tank, and simulated waste materials were included to represent the sticky waste on the tubes and the particulate waste settled beneath them. The testing program focused on assessing long-duration mining strategies for cleaning the cooling coils and removing the particulate waste forms. The report describes the results of the end effector testing program at PNNL. Section 2 describes the physical characteristics of the HLLW tanks, including the layout of the cooling coils, and it also describes what is known of the waste forms in the tanks. Section 3 describes the cleaning and retrieval strategy that was used in developing the end effector design. Section 4 describes the cooling coil mockup in the hydraulic test bed. Section 5 discusses the rationale used in selecting the simulants for the tarry waste and particulate waste forms. Section 6 describes the tests that were performed to evaluate cleaning of the cooling coils and retrieval of the particulate simulant. Section 7 summarizes the cleaning and retrieval tests, assesses the relative importance of cleaning the cooling coils and retrieving the particulate waste, and suggests modifications that would simplify the end effector design

Admission Test and Pregnancy Outcome

Directory of Open Access Journals (Sweden)

Setareh Akhavan

2017-07-01

Full Text Available Background: The admission test (AT has been carried out for many years, but there are still debates about the prognostic value of the test. Therefore, we aimed to examine the value of the AT in predicting the adverse outcome in neonates. Methods: In this cross-sectional study, 425 pregnant women with normal vaginal delivery were studied between2009 and 2014at Vali-e-Asr Hospital. Based on the results, the women were divided into 2groups of normal and abnormal ATs. All the patients were followed up until the birth of their baby, when the status of mother and neonate was determined. The main outcomes of the study were cesarean rate, neonatal intensive care unit (NICU admission, fetus demise, neonatal acidosis, and Apgar score. The independent t-test, chi-square test, Fisher exact test, and logistic regression were used for statistical analysis. The data were analyzed using SPSS (version 17. Results: Of 425 pregnant women studied, 142 (33.4% had abnormal ATs with a mean age of 29 (±4.5 years. Multivariate analysis showed that an abnormal AT was able to predict the incidence of cesarean section, intrauterine growth restriction, turned cord, and Apgar<7, but it could not predict neonatal death and hypoxia. Conclusion: The AT was shown to be a useful screening test with risk factors such as oligohydramnios, bloody amniotic fluid, meconium amniotic fluid, intrauterine growth restriction, and turned cord. Additionally, the test was also able to predict NICU admission and the need for cesarean section, but it could not predict the occurrence of neonatal death.

Predictors of HIV Testing among Youth in Sub-Saharan Africa: A Cross-Sectional Study.

Directory of Open Access Journals (Sweden)

Ibitola O Asaolu

Full Text Available In spite of a high prevalence of HIV infection among adolescents and young adults in sub-Saharan Africa, uptake of HIV testing and counseling among youth in the region remains sub-optimal. The objective of this study was to assess factors that influence uptake of HIV testing and counseling among youth aged 15-24 years in sub-Saharan Africa.This study used the Demographic and Health Survey (DHS data from countries that represent four geographic regions of sub-Saharan Africa: Congo (Brazzaville, representing central Africa (DHS 2011-2012; Mozambique, representing southern Africa (DHS 2011; Nigeria, representing western Africa (DHS 2013; and Uganda, representing eastern Africa (DHS 2011. Analyses were restricted to 23,367 male and female respondents aged 15-24 years with complete data on the variables of interest. Chi-square tests and logistic regression models were used to assess predictors of HIV testing. Statistical significance was set at p< 0.01.The analysis revealed that a majority of the respondents were female (78.1% and aged 20-24-years (60.7%. Only a limited proportion of respondents (36.5% had ever tested for HIV and even fewer (25.7% demonstrated comprehensive knowledge of HIV/AIDS. There was a significant association between HIV testing and respondents' gender, age, age at sexual debut, and comprehensive knowledge of HIV in the pooled sample. Older youth (adjusted OR (aOR = 2.19; 99% CI = 1.99-2.40 and those with comprehensive knowledge of HIV (aOR = 1.98; 1.76-2.22 had significantly higher odds of ever being tested for HIV than younger respondents and those with limited HIV/AIDS knowledge respectively. Furthermore, men had lower odds of HIV testing than women (aOR = 0.32; 0.28-0.37.Reaching youth in sub-Saharan Africa for HIV testing continues to be a challenge. Public health programs that seek to increase HIV counseling and testing among youth should pay particular attention to efforts that target high-risk subpopulations of youth

Influence of anesthesia techniques of caesarean section on memory, perception and speech

Directory of Open Access Journals (Sweden)

Volkov O.O.

2014-06-01

Full Text Available In obstetrics postoperative cognitive dysfunctions may take place after caesarean section and vaginal delivery with poor results both for mother and child. The goal was to study influence of anesthesia techniques following caesarian section on memory, perception and speech. Having agreed with local ethics committee and obtained informed consent depending on anesthesia method, pregnant women were divided into 2 groups: 1st group (n=31 had spinal anesthesia, 2nd group (n=34 – total intravenous anesthesia. Spinal anesthesia: 1.8-2.2 mLs of hyperbaric 0.5% bupivacaine. ТIVА: Thiopental sodium (4 mgs kg-1, succinylcholine (1-1.5 mgs kg-1. Phentanyl (10-5-3 µgs kg-1 hour and Diazepam (10 mgs were used after newborn extraction. We used Luria’s test for memory assessment, perception was studied by test “recognition of time”. Speech was studied by test "name of fingers". Control points: 1 - before the surgery, 2 - in 24h after the caesarian section, 3 - on day 3 after surgery, 4 - at discharge from hospital (5-7th day. The study showed that initially decreased memory level in expectant mothers regressed along with the time after caesarean section. Memory is restored in 3 days after surgery regardless of anesthesia techniques. In spinal anesthesia on 5-7th postoperative day memory level exceeds that of used in total intravenous anesthesia. The perception and speech do not depend on the term of postoperative period. Anesthesia technique does not influence perception and speech restoration after caesarean sections.

40 CFR 766.12 - Testing guidelines.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Testing guidelines. 766.12 Section 766... DIBENZO-PARA-DIOXINS/DIBENZOFURANS General Provisions § 766.12 Testing guidelines. Analytical test methods must be developed using methods equivalent to those described or reviewed in Guidelines for the...

30 CFR 36.41 - Testing methods.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Testing methods. 36.41 Section 36.41 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF... Requirements § 36.41 Testing methods. Mobile diesel-powered transportation equipment submitted for...

Utilization of Cell-Transfer Technique for Molecular Testing on Hematoxylin-Eosin-Stained Sections: A Viable Option for Small Biopsies That Lack Tumor Tissues in Paraffin Block.

Science.gov (United States)

Wu, Howard H; Jovonovich, Stephen M; Randolph, Melissa; Post, Kristin M; Sen, Joyashree D; Curless, Kendra; Cheng, Liang

2016-12-01

- In some instances the standard method of doing molecular testing from formalin-fixed, paraffin-embedded block is not possible because of limited tissue. Tumor cell-enriched cell-transfer technique has been proven useful for performing immunocytochemistry and molecular testing on cytologic smears. - To establish the cell-transfer technique as a viable option for isolating tumor cells from hematoxylin-eosin (H&E)-stained slides. - Molecular testing was performed by using the cell-transfer technique on 97 archived H&E-stained slides from a variety of different tumors. Results were compared to the conventional method of molecular testing. - Polymerase chain reaction-based molecular testing via the cell-transfer technique was successfully performed on 82 of 97 samples (85%). This included 39 of 47 cases for EGFR, 10 of 11 cases for BRAF, and 33 of 39 cases for KRAS mutations. Eighty-one of 82 cell-transfer technique samples (99%) showed agreement with previous standard method results, including 4 mutations and 35 wild-type alleles for EGFR, 4 mutations and 6 wild-type alleles for BRAF, and 11 mutations and 21 wild-type alleles for KRAS. There was only 1 discrepancy: a cell-transfer technique with a false-negative >KRAS result (wild type versus G12C). - Molecular testing performed on H&E-stained sections via cell-transfer technique is useful when tissue from cell blocks and small surgical biopsy samples is exhausted and the only available material for testing is on H&E-stained slides.

Artificial intelligence aiding the thin-section CT diagnosis of diffuse pulmonary diseases

International Nuclear Information System (INIS)

Han, Dae Hee; Koh, Young Hwan; Seong, Chang Kyu; Kim, Ji Hoon; Choi, Young Ho; Kim, Jong Hyo; Chae, Young Moon; Lee, Yun Hee; Han, Heon

2006-01-01

We wanted to develop and test an artificial intelligence (AI) to assist physicians in making the thin-section CT diagnosis of diffuse pulmonary diseases. The AI was composed of knowledge bases (KB) of 12 diffuse pulmonary diseases and an inference engine (IE). The KB of a disease included both the inclusion criteria (IC) and the exclusion criteria (EC), which were the clinical or thin-section CT findings that were known to be present or absent in that particular disease, respectively. From imputing the clinical or thin-section CT findings by the operator who was reading the thin-section CT, AI instantly executed the following two steps. First, the IE eliminated all diseases from the list which the EC had for those particular findings. Next, from a list or remaining diseases, the AI selected those diseases having those findings in its IC to formulate the 1st-step differential diagnosis (DD1). For the differential diagnosis in the next step, the reader could choose one more clinical or thin-section CT finding from the new list: [(all the findings in the IC or EC of DD1)-(the findings in the IC common to all the DD1s)]. The reader could proceed even further if needed. The system was tested on 10 radiology residents who solved 24 problems (two problems for each of 12 diffuse pulmonary diseases) without and then with the aid of the AI. The scores were compared using the Wilcoxon signed rank test. An AI was made; it was composed of 280 rules (214 IC and 66 EC) and there interfaces (two for program management and another for problem solving). Contestants scored higher (ρ = 0.0078) using the AI (167 vs. 110 respectively), and they responded that they felt that the program was helpful in making decisions. AI appeared to be helpful in making thin-section CT diagnosis

Artificial intelligence aiding the thin-section CT diagnosis of diffuse pulmonary diseases

Energy Technology Data Exchange (ETDEWEB)

Han, Dae Hee; Koh, Young Hwan; Seong, Chang Kyu; Kim, Ji Hoon; Choi, Young Ho [Boramae Munincipal Hospital, Seoul National University College of Medicine, Seoul (Korea, Republic of); Kim, Jong Hyo [Seoul National University College of Medicine, Seoul (Korea, Republic of); Chae, Young Moon [Yonsei University Graduate School of Public Heath, Seoul (Korea, Republic of); Lee, Yun Hee [The Graduate School of Imformation, Yonsei, Seoul (Korea, Republic of); Han, Heon [Kangwon National University College of Medicine, Chuncheon (Korea, Republic of)

2006-06-15

We wanted to develop and test an artificial intelligence (AI) to assist physicians in making the thin-section CT diagnosis of diffuse pulmonary diseases. The AI was composed of knowledge bases (KB) of 12 diffuse pulmonary diseases and an inference engine (IE). The KB of a disease included both the inclusion criteria (IC) and the exclusion criteria (EC), which were the clinical or thin-section CT findings that were known to be present or absent in that particular disease, respectively. From imputing the clinical or thin-section CT findings by the operator who was reading the thin-section CT, AI instantly executed the following two steps. First, the IE eliminated all diseases from the list which the EC had for those particular findings. Next, from a list or remaining diseases, the AI selected those diseases having those findings in its IC to formulate the 1st-step differential diagnosis (DD1). For the differential diagnosis in the next step, the reader could choose one more clinical or thin-section CT finding from the new list: [(all the findings in the IC or EC of DD1)-(the findings in the IC common to all the DD1s)]. The reader could proceed even further if needed. The system was tested on 10 radiology residents who solved 24 problems (two problems for each of 12 diffuse pulmonary diseases) without and then with the aid of the AI. The scores were compared using the Wilcoxon signed rank test. An AI was made; it was composed of 280 rules (214 IC and 66 EC) and there interfaces (two for program management and another for problem solving). Contestants scored higher ({rho} = 0.0078) using the AI (167 vs. 110 respectively), and they responded that they felt that the program was helpful in making decisions. AI appeared to be helpful in making thin-section CT diagnosis.

21 CFR 864.3260 - OTC test sample collection systems for drugs of abuse testing.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false OTC test sample collection systems for drugs of abuse testing. 864.3260 Section 864.3260 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES HEMATOLOGY AND PATHOLOGY DEVICES Pathology...

Standard Test Method for Testing Nonmetallic Seal Materials by Immersion in a Simulated Geothermal Test Fluid

CERN Document Server

American Society for Testing and Materials. Philadelphia

1985-01-01

1.1 This test method covers a procedure for a laboratory test for performing an initial evaluation (screening) of nonmetallic seal materials by immersion in a simulated geothermal test fluid. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 6 and 11.7.

33 CFR 183.590 - Fire test.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Fire test. 183.590 Section 183... SAFETY BOATS AND ASSOCIATED EQUIPMENT Fuel Systems Tests § 183.590 Fire test. (a) A piece of equipment is... A2” hoses and hose clamps are tested in a fire chamber. (2) Fuel filters, strainers, and pumps are...

12 CFR 228.22 - Lending test.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 3 2010-01-01 2010-01-01 false Lending test. 228.22 Section 228.22 Banks and... REINVESTMENT (REGULATION BB) Standards for Assessing Performance § 228.22 Lending test. (a) Scope of test. (1) The lending test evaluates a bank's record of helping to meet the credit needs of its assessment area...

12 CFR 228.24 - Service test.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 3 2010-01-01 2010-01-01 false Service test. 228.24 Section 228.24 Banks and... REINVESTMENT (REGULATION BB) Standards for Assessing Performance § 228.24 Service test. (a) Scope of test. The service test evaluates a bank's record of helping to meet the credit needs of its assessment area(s) by...

17 CFR 242.201 - Price test.

Science.gov (United States)

2010-04-01

... 17 Commodity and Securities Exchanges 3 2010-04-01 2010-04-01 false Price test. 242.201 Section...-Regulation of Short Sales § 242.201 Price test. Link to an amendment published at 75 FR 11323, Mar. 10, 2010. (a) No short sale price test, including any short sale price test of any self-regulatory organization...

Radiographic test phantom for computed tomographic lung nodule analysis

International Nuclear Information System (INIS)

Zerhouni, E.A.

1987-01-01

This patent describes a method for evaluating a computed tomograph scan of a nodule in a lung of a human or non-human animal. The method comprises generating a computer tomograph of a transverse section of the animal containing lung and nodule tissue, and generating a second computer tomograph of a test phantom comprising a device which simulates the transverse section of the animal. The tissue simulating portions of the device are constructed of materials having radiographic densities substantially identical to those of the corresponding tissue in the simulated transverse section of the animal and have voids therein which simulate, in size and shape, the lung cavities in the transverse section and which contain a test reference nodule constructed of a material of predetermined radiographic density which simulates in size, shape and position within a lung cavity void of the test phantom the nodule in the transverse section of the animal and comparing the respective tomographs

Economical Fabrication of Thick-Section Ceramic Matrix Composites

Science.gov (United States)

Babcock, Jason; Ramachandran, Gautham; Williams, Brian; Benander, Robert

2010-01-01

A method was developed for producing thick-section [>2 in. (approx.5 cm)], continuous fiber-reinforced ceramic matrix composites (CMCs). Ultramet-modified fiber interface coating and melt infiltration processing, developed previously for thin-section components, were used for the fabrication of CMCs that were an order of magnitude greater in thickness [up to 2.5 in. (approx.6.4 cm)]. Melt processing first involves infiltration of a fiber preform with the desired interface coating, and then with carbon to partially densify the preform. A molten refractory metal is then infiltrated and reacts with the excess carbon to form the carbide matrix without damaging the fiber reinforcement. Infiltration occurs from the inside out as the molten metal fills virtually all the available void space. Densification to thick-section components required modification of the conventional process conditions, and the means by which the large amount of molten metal is introduced into the fiber preform. Modification of the low-temperature, ultraviolet-enhanced chemical vapor deposition process used to apply interface coatings to the fiber preform was also required to accommodate the high preform thickness. The thick-section CMC processing developed in this work proved to be invaluable for component development, fabrication, and testing in two complementary efforts. In a project for the Army, involving SiC/SiC blisk development, nominally 0.8 in. thick x 8 in. diameter (approx. 2 cm thick x 20 cm diameter) components were successfully infiltrated. Blisk hubs were machined using diamond-embedded cutting tools and successfully spin-tested. Good ply uniformity and extremely low residual porosity (41 ksi (approx. 283 MPa) flexural strength.

Factors Affecting Result in Chinese Proficiency Test (HSK Level 6: Reading Section and Preparation Strategies

Directory of Open Access Journals (Sweden)

Sri Haryanti

2013-11-01

Full Text Available Chinese Proficiency Test (HSK is an internationally standardized exam which tests and rates Chinese language proficiency. The highest level in this test is level 6. The writing part of the test consists of 3 (three parts, namely, (1 listening, (2 reading, (3 writing. Furthermore, the reading part is made of 4 components. Level 6 of this test implies a high degree of difficulty. This paper specifically looked on how to prepare effectively for participants to be able to work on the reading part in order to achieve best result. This article used the methods of literature review and observational study as well as field research and would also incorporate the author’s personal experience in taking the test into recommending strategies for doing the reading part in a level 6 HSK test. Finally, research suggested several techniques and tips that might assist participants in achieving maximum scores in handling the reading part of level 6 HSK test.

Measurement of the cross-section of electron-positron scattering at high energy and quantum electrodynamics testing; Mesure de la section efficace de diffusion electron-positron a haute energie et validite de l'electrodynamique quantique

Energy Technology Data Exchange (ETDEWEB)

Lalanne, D.

1970-07-17

The experiment we have performed on the ACO (Orsay Collider Ring) is one of the most accurate tests of quantum electrodynamics over very short interaction distances (10{sup -14} cm). We have studied the electron-positron elastic scattering at very wide angle. This work is divided into 4 parts. The first part reviews recent tests of quantum electrodynamics and presents the electron-positron elastic scattering. The second part describes the measurement of brightness: the experimental device, data analysis and accuracy. The measurement of brightness has been performed by detecting the photons emitted in the double Bremsstrahlung reaction: e{sup +}e{sup -} → e{sup +}e{sup -}γγ. The third part deals with the measurement of the number of Bhabha events. The last part compares the experimental value of the Bhabha scattering with the theoretically expected value. We have got the following results: the number of Bhabha events: 757 events, the experimental value for Bhabha scattering cross-section: [1.97 ± 0.09 (stat.) ± 0.10 (syst.)]*10{sup -31} cm{sup 2}. The comparison of this experimental value with the expected value has allowed us to set the lower limit of the cutting parameter Λ: Λ > 2 GeV.

Individual-level characteristics associated with oral HIV test acceptability among Peruvian men who have sex with men and transgender women: a cross-sectional study.

Science.gov (United States)

Flores, Juan A; Brown, Brandon; León, Segundo R; Sánchez, Hugo; Galea, Jerome T

2018-03-24

Peruvian men who have sex with men (MSM) and transgender women (TGW) are highly vulnerable to HIV infection (HIV), but stigma, access issues and fear of venipuncture hamper testing. The oral HIV test-which uses oral fluids and provides results in 20 minutes-could reduce these barriers. The objective of this study was to determine the acceptability of the oral HIV test and the individual-level factors associated with its acceptability among MSM and TGW. We conducted a cross-sectional secondary analysis among Peruvian MSM and TGW attending a community-based health centre between February 2012 and February 2013 to determine the individual-level factors associated with oral HIV test acceptability. Of 334 participants, 88% were MSM and 12% TGW. Overall, 85% of participants indicated their acceptability of the oral HIV test. Acceptability was higher in MSM than TGW (85.7% vs 80.0%) but this difference was not significant. Factors associated with acceptability in MSM were: tertiary or higher education (prevalence ratio (PR)=1.18, 95% CI 1.06 to 1.32 and PR=1.16, 95% CI 1.03 to 1.30, respectively); sex with drug use (PR=1.19, 95% CI 1.05 to 1.36); believing that HIV is transmitted by saliva (PR=1.20, 95% CI 1.08 to 1.33); and potential use of the oral test at home (PR=1.56, 95% CI 1.32 to 1.85). The only factor associated with lower acceptability was having had first anal intercourse between 14 and 19 years of age (PR=0.89, 95% CI 0.80 to 0.98). We identified the individual factors associated with oral HIV test acceptability among Peruvian MSM and TGW. Expanded use of the oral HIV test to increase testing rates among Peruvian MSM and TGW is recommended. NCT01387412, post-results. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

IAG ring test animal proteins 2015

NARCIS (Netherlands)

Raamsdonk, van L.W.D.; Rhee, van de N.E.; Scholtens-Toma, I.M.J.; Prins, T.W.; Vliege, J.J.M.; Pinckaers, V.G.Z.

2015-01-01

A ring test was organized for the detection of animal proteins in animal feed by microscopy in the framework of the annual ring tests of the IAG - International Association for Feeding stuff Analysis, Section Feeding stuff Microscopy. The organizer of the ring test was RIKILT - Wageningen UR, The

49 CFR 192.243 - Nondestructive testing.

Science.gov (United States)

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Nondestructive testing. 192.243 Section 192.243... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Welding of Steel in Pipelines § 192.243 Nondestructive testing. (a) Nondestructive testing of welds must be performed by any process, other than trepanning, that...

10 CFR 71.123 - Test control.

Science.gov (United States)

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Test control. 71.123 Section 71.123 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) PACKAGING AND TRANSPORTATION OF RADIOACTIVE MATERIAL Quality Assurance § 71.123 Test control. The licensee, certificate holder, and applicant for a CoC shall establish a test...

9 CFR 147.52 - Approved tests.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Approved tests. 147.52 Section 147.52 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE... Approved Tests § 147.52 Approved tests. (a) The procedures for the bacteriological examination of poultry...

ENEA-Bologna production and testing of Jeff-3.1 multi-group cross section libraries for nuclear fission applications

International Nuclear Information System (INIS)

Pescarini, M.; Orsi, R.; Sinitsa, V.

2008-01-01

The ENEA-Bologna Nuclear Data Group produced the JEFF-3.1 VITJEFF31.BOLIB and MATJEFF31. BOLIB fine-group coupled neutron and photon (199 n + 42 γ) cross section libraries for nuclear fission applications, respectively in AMPX and MATXS format, with the same specifications and energy group structure of the Endf/B-VI-3 VITAMIN-B6 American library. Each library, containing 181 nuclide cross section files, was generated from the same set of cross section data files in GENDF format, obtained through the Bondarenko (f-factor) method, with an ENEA-Bologna revised version of the GROUPR module of the NJOY-99.160 system. Collapsed working libraries of self-shielded cross sections in FIDO-ANISN format, used by the deterministic transport codes of the DANTSYS and DOORS systems, can be generated from VITJEFF31.BOLIB and MATJEFF31.BOLIB through, respectively, further data processing with an ENEA-Bologna revised version of the SCAMPI system and with the TRANSX code. This paper describes the methodology and specifications of the data processing performed and presents some results of the VITJEFF31.BOLIB validation. (authors)

Predictors of HIV Testing among Youth in Sub-Saharan Africa: A Cross-Sectional Study.

Science.gov (United States)

Asaolu, Ibitola O; Gunn, Jayleen K; Center, Katherine E; Koss, Mary P; Iwelunmor, Juliet I; Ehiri, John E

2016-01-01

In spite of a high prevalence of HIV infection among adolescents and young adults in sub-Saharan Africa, uptake of HIV testing and counseling among youth in the region remains sub-optimal. The objective of this study was to assess factors that influence uptake of HIV testing and counseling among youth aged 15-24 years in sub-Saharan Africa. This study used the Demographic and Health Survey (DHS) data from countries that represent four geographic regions of sub-Saharan Africa: Congo (Brazzaville), representing central Africa (DHS 2011-2012); Mozambique, representing southern Africa (DHS 2011); Nigeria, representing western Africa (DHS 2013); and Uganda, representing eastern Africa (DHS 2011). Analyses were restricted to 23,367 male and female respondents aged 15-24 years with complete data on the variables of interest. Chi-square tests and logistic regression models were used to assess predictors of HIV testing. Statistical significance was set at psub-Saharan Africa for HIV testing continues to be a challenge. Public health programs that seek to increase HIV counseling and testing among youth should pay particular attention to efforts that target high-risk subpopulations of youth. The results further suggest that these initiatives would be strengthened by including strategies to increase HIV comprehensive knowledge.

Design of Test Loops for Forced Convection Heat Transfer Studies at Supercritical State

Science.gov (United States)

Balouch, Masih N.

Worldwide research is being conducted to improve the efficiency of nuclear power plants by using supercritical water (SCW) as the working fluid. One such SCW reactor considered for future development is the CANDU-Supercritical Water Reactor (CANDU-SCWR). For safe and accurate design of the CANDU-SCWR, a detailed knowledge of forced-convection heat transfer in SCW is required. For this purpose, two supercritical fluid loops, i.e. a SCW loop and an R-134a loop are developed at Carleton University. The SCW loop is designed to operate at pressures as high as 28 MPa, temperatures up to 600 °C and mass fluxes of up to 3000 kg/m2s. The R-134a loop is designed to operate at pressures as high as 6 MPa, temperatures up to 140 °C and mass fluxes in the range of 500-6000 kg/m2s. The test loops designs allow for up to 300 kW of heating power to be imparted to the fluid. Both test loops are of the closed-loop design, where flow circulation is achieved by a centrifugal pump in the SCW loop and three parallel-connected gear pumps in the R-134a loop, respectively. The test loops are pressurized using a high-pressure nitrogen cylinder and accumulator assembly, which allows independent control of the pressure, while simultaneously dampening pump induced pressure fluctuations. Heat exchangers located upstream of the pumps control the fluid temperature in the test loops. Strategically located measuring instrumentation provides information on the flow rate, pressure and temperature in the test loops. The test loops have been designed to accommodate a variety of test-section geometries, ranging from a straight circular tube to a seven-rod bundle, achieving heat fluxes up to 2.5 MW/m2 depending on the test-section geometry. The design of both test loops allows for easy reconfiguration of the test-section orientation relative to the gravitational direction. All the test sections are of the directly-heated design, where electric current passing through the pressure retaining walls of the

A Pebble Bed Reactor cross section methodology

International Nuclear Information System (INIS)

Hudson, Nathanael H.; Ougouag, Abderrafi M.; Rahnema, Farzad; Gougar, Hans

2009-01-01

A method is presented for the evaluation of microscopic cross sections for the Pebble Bed Reactor (PBR) neutron diffusion computational models during convergence to an equilibrium (asymptotic) fuel cycle. This method considers the isotopics within a core spectral zone and the leakages from such a zone as they arise during reactor operation. The randomness of the spatial distribution of fuel grains within the fuel pebbles and that of the fuel and moderator pebbles within the core, the double heterogeneity of the fuel, and the indeterminate burnup of the spectral zones all pose a unique challenge for the computation of the local microscopic cross sections. As prior knowledge of the equilibrium composition and leakage is not available, it is necessary to repeatedly re-compute the group constants with updated zone information. A method is presented to account for local spectral zone composition and leakage effects without resorting to frequent spectrum code calls. Fine group data are pre-computed for a range of isotopic states. Microscopic cross sections and zone nuclide number densities are used to construct fine group macroscopic cross sections, which, together with fission spectra, flux modulation factors, and zone buckling, are used in the solution of the slowing down balance to generate a new or updated spectrum. The microscopic cross-sections are then re-collapsed with the new spectrum for the local spectral zone. This technique is named the Spectral History Correction (SHC) method. It is found that this method accurately recalculates local broad group microscopic cross sections. Significant improvement in the core eigenvalue, flux, and power peaking factor is observed when the local cross sections are corrected for the effects of the spectral zone composition and leakage in two-dimensional PBR test problems.

10 CFR 707.7 - Random drug testing requirements and identification of testing designated positions.

Science.gov (United States)

2010-01-01

... contractor, to have the potential to significantly affect the environment, public health and safety, or... evidence of the use of illegal drugs of employees in testing designated positions identified in this... section shall provide for random tests at a rate equal to 30 percent of the total number of employees in...

Ice condenser testing facility and plans

International Nuclear Information System (INIS)

Kannberg, L.D.; Ross, B.A.; Eschbach, E.J.; Ligotke, M.W.

1987-01-01

A facility is being constructed to experimentally validate the ICEDF computer code. The code was developed to estimate the extent of fission product retention in the ice compartments of pressurized water reactor ice condenser containment systems during severe accidents. The design and construction of the facility is based on a test design that addresses the validation needs of the code for conditions typical of those expected to occur during severe pressurized water reactor accidents. Detailed facility design has followed completion of a test design (i.e., assembled test cases each involving a different set of aerosol and thermohydraulic flow conditions). The test design was developed with the aid of statistical test design software and was scrutinized for applicability with the aid of ICEDF simulations. The test facility will incorporate a small section of a prototypic ice condenser (e.g., a cross section comprising the equivalent of four 1-ft-diameter ice baskets to their full prototypic height of 48 ft). The development of the test design, the detailed facility design, and the construction progress are described in this paper

Launch Control System Software Development System Automation Testing

Science.gov (United States)

Hwang, Andrew

2017-01-01

The Spaceport Command and Control System (SCCS) is the National Aeronautics and Space Administration's (NASA) launch control system for the Orion capsule and Space Launch System, the next generation manned rocket currently in development. This system requires high quality testing that will measure and test the capabilities of the system. For the past two years, the Exploration and Operations Division at Kennedy Space Center (KSC) has assigned a group including interns and full-time engineers to develop automated tests to save the project time and money. The team worked on automating the testing process for the SCCS GUI that would use streamed simulated data from the testing servers to produce data, plots, statuses, etc. to the GUI. The software used to develop automated tests included an automated testing framework and an automation library. The automated testing framework has a tabular-style syntax, which means the functionality of a line of code must have the appropriate number of tabs for the line to function as intended. The header section contains either paths to custom resources or the names of libraries being used. The automation library contains functionality to automate anything that appears on a desired screen with the use of image recognition software to detect and control GUI components. The data section contains any data values strictly created for the current testing file. The body section holds the tests that are being run. The function section can include any number of functions that may be used by the current testing file or any other file that resources it. The resources and body section are required for all test files; the data and function sections can be left empty if the data values and functions being used are from a resourced library or another file. To help equip the automation team with better tools, the Project Lead of the Automated Testing Team, Jason Kapusta, assigned the task to install and train an optical character recognition (OCR

Pion photoproduction cross section at large momentum transfer

Energy Technology Data Exchange (ETDEWEB)

Sjoegren, Johan [Univ. of Glasgow, Scotland, United Kingdom

2015-02-27

The Real Compton Scattering experiment was performed in Hall A at the Thomas Jefferson National Accelerator Facility. It was designed to measure, for Compton scattering and π⁰-photoproduction, the differential cross section over a range of kinematic points and the polarisation transfer to the proton at a single kinematic point. The full range of the experiment in Mandelstam variables t and s was 1.6-6.46 GeV² and 4.82-10.92 GeV² respectively with beam energies of 2-6 GeV. The motivation for the experiment is to test the cross section and polarisation transfer predictions of perturbative QCD versus that of predictions from Generalised Parton Distribution models. This thesis will give an overview of the pertinent theory, experimental setup in Hall A and the extracting of the π⁰-photoproduction cross section.

Summary of ALSEP Test Loop Solvent Irradiation Testing

Energy Technology Data Exchange (ETDEWEB)

Peterman, Dean Richard [Idaho National Lab. (INL), Idaho Falls, ID (United States); Olson, Lonnie Gene [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-08-01

Separating the minor actinide elements (americium and curium) from the fission product lanthanides is an important step in closing the nuclear fuel cycle. Isolating the minor actinides will allow transmuting them to short lived or stable isotopes in fast reactors, thereby reducing the long-term hazard associated with these elements. The Actinide Lanthanide Separation Process (ALSEP) is being developed by the DOE-NE Material Recovery and Waste Form Development Campaign to accomplish this separation with a single process. To develop a fundamental understanding of the solvent degradation mechanisms for the ALSEP Process, testing was performed in the INL Radiolysis/Hydrolysis Test Loop for the extraction section of the ALSEP flowsheet. This work culminated in the completion of the level two milestone (M2FT-16IN030102021) "Complete ALSEP test loop solvent irradiation test.” This report summarizes the testing performed and the impact of radiation on the ALSEP Process performance as a function of dose.

46 CFR 154.449 - Model test.

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Model test. 154.449 Section 154.449 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY STANDARDS FOR SELF... § 154.449 Model test. The following analyzed data of a model test of structural elements for independent...

49 CFR 178.605 - Hydrostatic pressure test.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Hydrostatic pressure test. 178.605 Section 178.605... Testing of Non-bulk Packagings and Packages § 178.605 Hydrostatic pressure test. (a) General. The hydrostatic pressure test must be conducted for the qualification of all metal, plastic, and composite...

Effective Cross Section of Cold Formed Steel Column Under Axial Compression

Science.gov (United States)

Manikandan, P.; Pradeep, T.

2018-06-01

The compressive resistance of cold-formed steel (CFS) section may be governed by local, distortional or overall buckling and any apparent interaction between these modes. A new inventive stiffened CFS section is elected in this study, selected cross sections geometries and lengths are chosen such that all the types of buckling modes are met with. Buckling plot is plotted using linear elastic buckling analysis software (CUFSM). Using the test results obtained in the literature, the developed finite element model is calibrated and furthers a total of 126 parametric study is conducted such as a consequence of dimensions and the length of the cross section, thickness and yield stress. The FEA included relevant material and geometric imperfections. All the columns are analyzed under pin end conditions with axial compression. The analysis results demonstrate that the DSM equations generally assess the strength of stiffened section conservatively. Modifications to the DSM equations are recommended to evaluate the strength of stiffened section more precisely.

Effective Cross Section of Cold Formed Steel Column Under Axial Compression

Science.gov (United States)

Manikandan, P.; Pradeep, T.

2018-02-01

The compressive resistance of cold-formed steel (CFS) section may be governed by local, distortional or overall buckling and any apparent interaction between these modes. A new inventive stiffened CFS section is elected in this study, selected cross sections geometries and lengths are chosen such that all the types of buckling modes are met with. Buckling plot is plotted using linear elastic buckling analysis software (CUFSM). Using the test results obtained in the literature, the developed finite element model is calibrated and furthers a total of 126 parametric study is conducted such as a consequence of dimensions and the length of the cross section, thickness and yield stress. The FEA included relevant material and geometric imperfections. All the columns are analyzed under pin end conditions with axial compression. The analysis results demonstrate that the DSM equations generally assess the strength of stiffened section conservatively. Modifications to the DSM equations are recommended to evaluate the strength of stiffened section more precisely.

Mantoux Tuberculin Skin Test

Centers for Disease Control (CDC) Podcasts

2006-11-22

Learn how to evaluate people for latent TB infection with the Mantoux tuberculin skin test. This podcast includes sections on administering and reading the Mantoux tuberculin skin test, the standard method for detecting latent TB infection since the 1930s.  Created: 11/22/2006 by National Center for HIV, STD and TB Prevention (NCHHSTP).   Date Released: 12/12/2006.

9 CFR 55.8 - Official CWD tests and approval of laboratories to conduct official CWD tests.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Official CWD tests and approval of laboratories to conduct official CWD tests. 55.8 Section 55.8 Animals and Animal Products ANIMAL AND PLANT... on live or dead animals, and will base the approval or disapproval of a test on the evaluation by...

46 CFR 154.430 - Material test.

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Material test. 154.430 Section 154.430 Shipping COAST... § 154.430 Material test. (a) The membrane and the membrane supporting insulation must be made of... test for the membrane and the membrane supporting insulation must be submitted to the Commandant (CG...

Testing as a service with HammerCloud

International Nuclear Information System (INIS)

Llamas, Ramón Medrano; Barrand, Quentin; Sciabà, Andrea; Ster, Daniel van der; Elmsheuser, Johannes; Legger, Federica; Sciacca, Gianfranco

2014-01-01

HammerCloud was designed and born under the needs of the grid community to test the resources and automate operations from a user perspective. The recent developments in the IT space propose a shift to the software defined data centres, in which every layer of the infrastructure can be offered as a service. Testing and monitoring is an integral part of the development, validation and operations of big systems, like the grid. This area is not escaping the paradigm shift and we are starting to perceive as natural the Testing as a Service (TaaS) offerings, which allow testing any infrastructure service, such as the Infrastructure as a Service (IaaS) platforms being deployed in many grid sites, both from the functional and stressing perspectives. This work will review the recent developments in HammerCloud and its evolution to a TaaS conception, in particular its deployment on the Agile Infrastructure platform at CERN and the testing of many IaaS providers across Europe in the context of experiment requirements. The first section will review the architectural changes that a service running in the cloud needs, such an orchestration service or new storage requirements in order to provide functional and stress testing. The second section will review the first tests of infrastructure providers on the perspective of the challenges discovered from the architectural point of view. Finally, the third section will evaluate future requirements of scalability and features to increase testing productivity.

Heavy-Section Steel Technology Program

International Nuclear Information System (INIS)

Pennell, W.E.

1992-11-01

The Heavy-Section Steel Technology (HSST) Program is conducted for the Nuclear Regulatory Commission (NRC) by Oak Ridge National Laboratory (ORNL). The program focus is on the development and validation of technology for the assessment of fracture-prevention margins in commercial nuclear reactor pressure vessels. The HSST Program is organized in 11 tasks: program management, fracture methodology and analysis, material characterization and properties, special technical assistance, fracture analysis computer programs, cleavage-crack initiation, cladding evaluations, pressurized-thermal-shock technology, analysis methods validation, fracture evaluation tests, and warm prestressing. The program tasks have been structured to place emphasis on the resolution fracture issues with near-term licensing significance. Resources to execute the research tasks are drawn from ORNL with subcontract support from universities and other research laboratories. Close contact is maintained with the sister Heavy-Section Steel Irradiation (HSSI) Program at ORNL and with related research programs both in the United States and abroad. This report provides an overview of principal developments in each of the II program tasks from October 1, 1991 to March 31, 1992

Sodium test of the Super-Phenix full size primary pump shaft on the CPV-1 test rig at ENEA-Brasimone

International Nuclear Information System (INIS)

Contardi, T.; Rapezzi, L.; Partiti, C.; Zola, M.; Denimal, P.

1984-01-01

Tests on FBR Superphenix primary pump shaft were performed within the sodium-cooled FBR common research and development programs provided for by the cooperation agreement between ENEA and CEA. These tests were performed in CPV-1 plant ENEA - Brasimone Energy Research Center. The CPV-1 rig was built by FIAT-TTG and reproduces the reactor operating conditions (sodium-temperature and level, shaft inclination, etc..). Furthermore, CPV-1 rig's most interesting feature is its possibility to apply seismic stresses to test section by means of an oleodynamic actuator. Pivoterie-1 test section was made by JEUMONT-SCHNEIDER which built Superphenix pumps too; it was given to ENEA by FIAT-TTG. Seismic tests were performed with the cooperation of ISMES and FIAT-TTG. (author)

Standard practice for fracture testing with surface-crack tension specimens

CERN Document Server

American Society for Testing and Materials. Philadelphia

2003-01-01

1.1 This practice covers the design, preparation, and testing of surface-crack tension (SCT) specimens. It relates specifically to testing under continuously increasing force and excludes cyclic and sustained loadings. The quantity determined is the residual strength of a specimen having a semielliptical or circular-segment fatigue crack in one surface. This value depends on the crack dimensions and the specimen thickness as well as the characteristics of the material. 1.2 Metallic materials that can be tested are not limited by strength, thickness, or toughness. However, tests of thick specimens of tough materials may require a tension test machine of extremely high capacity. The applicability of this practice to nonmetallic materials has not been determined. 1.3 This practice is limited to specimens having a uniform rectangular cross section in the test section. The test section width and length must be large with respect to the crack length. Crack depth and length should be chosen to suit the ultimate pu...

30 CFR 7.48 - Acid resistance test.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Acid resistance test. 7.48 Section 7.48 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Battery Assemblies § 7.48 Acid resistance test. (a...

An intersection test for panel unit roots

NARCIS (Netherlands)

Hanck, C.

2013-01-01

This article proposes a new panel unit root test based on Simes' ( 1986) classical intersection test. The test is robust to general patterns of cross-sectional dependence and yet is straightforward to implement, only requiring p-values of time series unit root tests of the series in the panel, and

21 CFR 870.3690 - Pacemaker test magnet.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Pacemaker test magnet. 870.3690 Section 870.3690...) MEDICAL DEVICES CARDIOVASCULAR DEVICES Cardiovascular Prosthetic Devices § 870.3690 Pacemaker test magnet. (a) Identification. A pacemaker test magnet is a device used to test an inhibited or triggered type...

46 CFR 4.03-7 - Chemical test.

Science.gov (United States)

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Chemical test. 4.03-7 Section 4.03-7 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY PROCEDURES APPLICABLE TO THE PUBLIC MARINE CASUALTIES AND INVESTIGATIONS Definitions § 4.03-7 Chemical test. The term chemical test means a scientifically recognized test...

Novel development of the micro-tensile test at elevated temperature using a test structure with integrated micro-heater

Science.gov (United States)

Ang, W. C.; Kropelnicki, P.; Soe, Oak; Ling, J. H. L.; Randles, A. B.; Hum, A. J. W.; Tsai, J. M. L.; Tay, A. A. O.; Leong, K. C.; Tan, C. S.

2012-08-01

This paper describes the novel development of a micro-tensile testing method that allows testing at elevated temperatures. Instead of using a furnace, a titanium/platinum thin film micro-heater was fabricated on a conventional dog-bone-shaped test structure to heat up its gauge section locally. An infrared (IR) camera with 5 µm resolution was employed to verify the temperature uniformity across the gauge section of the test structure. With this micro-heater-integrated test structure, micro-tensile tests can be performed at elevated temperatures using any conventional tensile testing system without any major modification to the system. In this study, the tensile test of the single crystal silicon (SCS) thin film with (1 0 0) surface orientation and tensile direction was performed at room temperature and elevated temperatures, up to 300 °C. Experimental results for Young's modulus as a function of temperature are presented. A micro-sized SCS film showed a low dependence of mechanical properties on temperature up to 300 °C.

Data report of a tight-lattice rod bundle thermal-hydraulic tests (1). Base case test using 37-rod bundle simulated water-cooled breeder reactor (Contract research)

International Nuclear Information System (INIS)

Kureta, Masatoshi; Tamai, Hidesada; Liu, Wei; Akimoto, Hajime; Sato, Takashi; Watanabe, Hironori; Ohnuki, Akira

2006-03-01

Japan Atomic Energy Agency has been performing tight-lattice rod bundle thermal-hydraulic tests to realize essential technologies for the technological and engineering feasibility of super high burn-up water-cooled breeder reactor featured by a high breeding ratio and super high burn-up by reducing the core water volume in water-cooled reactor. The tests are performing to make clear the fundamental subjects related to the boiling transition (BT) (Subjects: BT criteria under a highly tight-lattice rod bundle, effects of gap-width between rods and of rod-bowing) using 37-rod bundles (Base case test section (1.3mm gap-width), Two parameter effect test sections (Gap-width effect one (1.0mm) and Rod-bowing one)). In the present report, we summarize the test results from the base case test section. The thermal-hydraulic characteristics using the large scale test section were obtained for the critical power, the pressure drop and the wall heat transfer under a wide range of pressure, flow rate, etc. including normal operational conditions of the designed reactor. Effects of local peaking factor on the critical power were also obtained. (author)

46 CFR 151.03-38 - Nondestructive testing.

Science.gov (United States)

2010-10-01

... CARRYING BULK LIQUID HAZARDOUS MATERIAL CARGOES Definitions § 151.03-38 Nondestructive testing. Nondestructive testing includes ultrasonic examination, liquid penetrant examination, magnetic particle... 46 Shipping 5 2010-10-01 2010-10-01 false Nondestructive testing. 151.03-38 Section 151.03-38...

Feasibility Study for the Measurement of Nuclear Fragmentation Cross Sections with NA61/SHINE at the CERN SPS

CERN Document Server

Aduszkiewicz, A

2017-01-01

A detailed knowledge of the fragmentation cross sections of intermediate mass nuclei is of paramount importance to understand the propagation of cosmic rays in our Galaxy and to evaluate the background for dark matter searches with space-based cosmic-ray experiments such as AMS. Therefore, we suggest a one-week test run in 2018 with secondary ions to establish the capabilities of NA61/SHINE to measure fragmentation cross sections at isotope level. No major modifications to the experimental setup of NA61/SHINE are needed to perform this feasibility study. The experience gained during the test run will be used to formulate a comprehensive measurement campaign for cosmic-ray related fragmentation cross sections for the possible extension of the NA61/SHINE physics program beyond 2020. The test data on carbon-proton and oxygen-proton interactions at 13A GeV/c that we intend to collect during the proposed test run have already the potential to reduce the current cross section uncertainties.

Maternal and neonatal copeptin levels at cesarean section and vaginal delivery.

Science.gov (United States)

Foda, Ashraf A; Abdel Aal, Ibrahim A

2012-12-01

The objective of the study was to measure the copeptin levels in maternal serum and umbilical cord serum at cesarean section and vaginal delivery in normotensive pregnancy and pre-eclamptic women. This was a prospective study at Mansoura University Hospital, Egypt. Ninety cases were included. They were divided into six groups: (1) normal pregnancy near term, as a control group, (2) primiparas who had vaginal delivery, (3) primiparas who had vaginal delivery and mild preeclampsia, (4) elective repeat cesarean section, (5) intrapartum cesarean section for indications other than fetal distress, and (6) intrapartum cesarean section for fetal distress. Serum copeptin concentrations were quantified with an enzyme-linked immunosorbent assay (ELISA). Mean, standard deviation, and paired t-test were used to test for significant change in quantitative data. The vaginal delivery groups had higher levels of maternal serum copeptin than the elective cesarean section group (P<0.01). Higher maternal serum copeptin levels were found in cases with pre-eclampsia as compared with the normotensive cases. The maternal copeptin levels during intrapartum cesarean section were higher than that during elective repeat cesarean section. There was a significant correlation between maternal copeptin levels and the duration of the first stage. In the presence of fetal distress, umbilical cord serum copeptin levels were significantly higher than other groups. Vaginal delivery can be very painful and stressful, and is accompanied by a marked increase of maternal serum copeptin. Increased maternal levels of serum copeptin were found in cases with pre-eclampsia as compared with the normotensive cases, and it may be helpful in assessing the disease. Intrauterine fetal distress is a strong stimulus to the release of copeptin into the fetal circulation. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

Visualization of flaws within heavy section ultrasonic test blocks using high energy computed tomography

International Nuclear Information System (INIS)

House, M.B.; Ross, D.M.; Janucik, F.X.; Friedman, W.D.; Yancey, R.N.

1996-05-01

The feasibility of high energy computed tomography (9 MeV) to detect volumetric and planar discontinuities in large pressure vessel mock-up blocks was studied. The data supplied by the manufacturer of the test blocks on the intended flaw geometry were compared to manual, contact ultrasonic test and computed tomography test data. Subsequently, a visualization program was used to construct fully three-dimensional morphological information enabling interactive data analysis on the detected flaws. Density isosurfaces show the relative shape and location of the volumetric defects within the mock-up blocks. Such a technique may be used to qualify personnel or newly developed ultrasonic test methods without the associated high cost of destructive evaluation. Data is presented showing the capability of the volumetric data analysis program to overlay the computed tomography and destructive evaluation (serial metallography) data for a direct, three-dimensional comparison

Compatibility of Clinical Manifestation with Skin Prick Test Result and Food Provocation Test in Food Cross Reaction

OpenAIRE

Lubis, Azwin; Barlianto, Wisnu; Endaryanto, Anang; Harsono, Ariyanto

2017-01-01

Background: Subjective diagnostic test of food allergy is hugely biased, resulting in irrational diet avoidance. Additional objective tools by skin prick test following food provocation test resulting more accurate cause and prevalence on population. Purpose: To evaluate the compatibility of clinical symptoms with skin prick test and provocation test for imunoglobulin E (IgE) mediated food allergy in Dr. Soetomo Hospital Surabaya. Methods: Cross sectional observational analytic study. Patient...

ENEA-Bologna production and testing of JEF-2.2 multi-group cross section libraries for nuclear fission applications

International Nuclear Information System (INIS)

Pescarini, M.; Orsi, R.; Martinelli, T.; Sinitsa, V.; Blokhin, A.I.

2005-01-01

The ENEA-Bologna Nuclear Data Group produced the VITJEF22.BOLIB (NEA-1699/01 ZZ VITJEF22.BOLIB) and MATJEF22.BOLIB (NEA-1740/01 ZZ MATJEF22.BOLIB) fine-group coupled neutron and photon (199 n + 42 γ) cross section libraries for nuclear fission applications, respectively in AMPX and MATXS format and based on the JEF-2.2 European nuclear data file. Both the libraries were produced from the same set of cross section files in GENDF format, generated with the NJOY-94.66 nuclear data processing system. The present libraries can be considered as European counterparts of the VITAMIN-B6 (DLC-0184 ZZ VITAMIN-B6) American library in AMPX format, based on the ENDF/B-VI Release 3 American nuclear data file. In fact they have the same general features and the same neutron and photon energy group structures as VITAMIN-B6. In particular, all these libraries are pseudo-problem-independent and based on the Bondarenko (f-factor) method for the treatment of neutron resonance self-shielding and temperature effects. Each ENEA-Bologna library contains a set of 133 nuclide cross section files processed at 4 temperatures (300 K, 600 K, 1000 K and 2100 K) and obtained for the most part with 6 to 8 values of the background cross section σ 0 . Thermal scattering cross sections were processed at all the temperatures available in the JEF-2.2 thermal scattering law data file for 5 additional bound nuclides: H-1 in light water, H-1 in polyethylene, H-2 in heavy water, C in graphite and Be in beryllium metal. Collapsed working libraries of self-shielded cross sections in the formats used by the deterministic transport codes of the DANTSYS and DOORS systems can be generated from VITJEF22.BOLIB and MATJEF22.BOLIB through, respectively, further problem-dependent data processing with the AMPX or SCAMPI nuclear data processing systems and with the TRANSX code. (authors)

High gradient tests of SLAC Linear Collider Accelerator Structures

International Nuclear Information System (INIS)

Wang, J.W.; Deruyter, H.; Eichner, J.; Fant, K.H.; Hoag, H.A.; Koontz, R.F.; Lavine, T.; Loew, G.A.; Loewen, R.; Menegat, L.

1994-08-01

This paper describes the current SLAC R ampersand D program to develop room temperature accelerator structures for the Next Linear Collider (NLC). The structures are designed to operate at 11.4 GHz at an accelerating gradient in the range of 50 to 100 MV/m. In the past year a 26 cm constant-impedance traveling-wave section, a 75 cm constant-impedance traveling-wave section, and a 1.8 m traveling-wave section with detuned deflecting modes have been high-power tested. The paper presents a brief description of the RF test setup, the design and manufacturing details of the structures, and a discussion of test results including field emission, RF processing, dark current spectrum and RF breakdown

Crashworthy airframe design concepts: Fabrication and testing

Science.gov (United States)

Cronkhite, J. D.; Berry, V. L.

1982-01-01

Crashworthy floor concepts applicable to general aviation aircraft metal airframe structures were investigated. Initially several energy absorbing lower fuselage structure concepts were evaluated. Full scale floor sections representative of a twin engine, general aviation airplane lower fuselage structure were designed and fabricated. The floors featured an upper high strength platform with an energy absorbing, crushable structure underneath. Eighteen floors were fabricated that incorporated five different crushable subfloor concepts. The floors were then evaluated through static and dynamic testing. Computer programs NASTRAN and KRASH were used for the static and dynamic analysis of the floor section designs. Two twin engine airplane fuselages were modified to incorporate the most promising crashworthy floor sections for test evaluation.

Technical justification for ASME code section xi crack detection by visual examination

International Nuclear Information System (INIS)

Nickell, R.E.; Rashid, Y.R.

2001-01-01

A critical technical element of nuclear power plant license renewal in the United States is the demonstration that the effects of aging do not compromise the intended safety function(s) of a system, structure, or component during the extended term of operation. The demonstration may take either of two forms. First, it can be shown that the design basis for the system, structure, or component is sufficiently robust that the aging effects have been insignificant through the current license term, and will continue to be insignificant through the extended term. Alternatively, it can be shown that, while the aging effects may be potentially significant, those effects can be managed and functionality maintained by defined programmatic activities during the extended term of operation. The first of the two approaches is generally provided by the construction basis, such as construction in accordance with the ASME Code Section III and other consensus codes and standards. The second of the two approaches is often provided by periodic inservice inspection and testing, in accordance with the ASME Code Section XI. The purpose of the ASME Section XI inspections and tests is to assure that systems, components, and structures are fit for continued service until the next scheduled inspection or test. The purpose of this paper is to document the effectiveness of the current ASME Code Section XI visual examination procedures in detecting the effects of aging for systems, structures, and components that are tolerant of mature cracks. (author)

Implementation of the rapid cross section adjustment approach at General Electric

International Nuclear Information System (INIS)

Cowan, C.L.; Kujawski, E.; Protsik, R.

1978-01-01

The General Electric rapid cross section adjustment approach was developed to use the shielding factor method for formulating multigroup cross sections. In this approach, space- and composition-dependent cross sections for a particular reactor or shield design are prepared from a generalized cross section library by the use of resonance self-shielding factors, and by the adjustment of elastic scattering cross sections for the local neutron flux spectra. The principal tool in the cross section adjustment package is the data processing code TDOWN. This code was specified to give the user a high degree of flexibility in the analysis of advanced reactor designs. Of particular interest in the analysis of critical experiments is the ability to carry out cell heterogeneity self-shielding calculations using a multiregion equivalence relationship, and the homogenization of the cross sections over the specified cell with the flux weighting obtained from transport theory calculations. Extensive testing of the rapid cross section adjustment approach, including comparisons with Monte Carlo methods, indicated that this approach can be utilized with a high degree of confidence in the design analysis of complex fast reactor systems. 2 figures, 1 table

A suspected case of rocuronium-sugammadex complex-induced anaphylactic shock after cesarean section.

Science.gov (United States)

Yamaoka, Masakazu; Deguchi, Miki; Ninomiya, Kiichiro; Kurasako, Toshiaki; Matsumoto, Mutsuko

2017-02-01

An anaphylactic reaction during a cesarean section occurs rarely, and rocuronium is thought to be one of the common agents causing perioperative anaphylaxis. Here we report an anaphylactic shock after cesarean section that is suggested to be induced by the rocuronium-sugammadex complex. A 36-year-old primigravida underwent an elective cesarean section under general anesthesia due to placenta previa. While the operation was completed uneventfully, she developed anaphylactic shock following sugammadex administration. She was successfully managed with rapid treatments. Serum tryptase level was significantly elevated. Although sugammadex was first suspected to be the causative agent, the result of intradermal skin tests with sugammadex were negative. Surprisingly, a subsequent intradermal test with undiluted rocuronium caused the patient to fall into a state of shock. Furthermore, a later skin-prick test with pre-mixed rocuronium-sugammadex complex also revealed a strong positive reaction, and a test with only rocuronium showed negative. We finally concluded that the rocuronium-sugammadex complex is the causative agent in this case. To the best of our knowledge, this is the first report suggesting anaphylaxis caused by the rocuronium-sugammadex complex. This case highlights the importance of appropriate examinations to determinate the pathogenesis of anaphylaxis in order to establish risk reduction strategies.

49 CFR 391.31 - Road test.

Science.gov (United States)

2010-10-01

... 49 Transportation 5 2010-10-01 2010-10-01 false Road test. 391.31 Section 391.31 Transportation... COMBINATION VEHICLE (LCV) DRIVER INSTRUCTORS Tests § 391.31 Road test. (a) Except as provided in subpart G, a person shall not drive a commercial motor vehicle unless he/she has first successfully completed a road...