WorldWideScience

Sample records for test instrumentation supporting

  1. Status Report on Efforts to Enhance Instrumentation to Support Advanced Test Reactor Irradiations

    Energy Technology Data Exchange (ETDEWEB)

    J. L. Rempe; D. L. Knudson; J. E. Daw

    2011-03-01

    The Department of Energy (DOE) designated the Advanced Test Reactor (ATR) as a National Scientific User Facility (NSUF) in April 2007 to support U.S. leadership in nuclear science and technology. By attracting new research users - universities, laboratories, and industry - the ATR NSUF facilitates basic and applied nuclear research and development, further advancing the nation's energy security needs. A key component of the ATR NSUF effort is to prove new in-pile instrumentation techniques that are capable of providing real-time measurements of key parameters during irradiation. To address this need, an assessment of instrumentation available and under-development at other test reactors was completed. Based on this review, recommendations were made with respect to what instrumentation is needed at the ATR; and a strategy was developed for obtaining these sensors. In 2009, a report was issued documenting this program’s strategy and initial progress toward accomplishing program objectives. In 2009, a report was issued documenting this instrumentation development strategy and initial progress toward accomplishing instrumentation development program objectives. This document reports progress toward implementing this strategy in 2010.

  2. Status Report on Efforts to Enhance Instrumentation to Support Advanced Test Reactor Irradiations

    Energy Technology Data Exchange (ETDEWEB)

    J. Rempe; D. Knudson; J. Daw; T. Unruh; B. Chase; R. Schley; J. Palmer; K. Condie

    2014-01-01

    The Department of Energy (DOE) designated the Advanced Test Reactor (ATR) as a National Scientific User Facility (NSUF) in April 2007 to support the growth of nuclear science and technology in the United States (US). By attracting new research users - universities, laboratories, and industry - the ATR NSUF facilitates basic and applied nuclear research and development, further advancing the nation's energy security needs. A key component of the ATR NSUF effort at the Idaho National Laboratory (INL) is to design, develop, and deploy new in-pile instrumentation techniques that are capable of providing real-time measurements of key parameters during irradiation. To address this need, an assessment of instrumentation available and under-development at other test reactors was completed. Based on this initial review, recommendations were made with respect to what instrumentation is needed at the ATR, and a strategy was developed for obtaining these sensors. In 2009, a report was issued documenting this program’s strategy and initial progress toward accomplishing program objectives. Since 2009, annual reports have been issued to provide updates on the program strategy and the progress made on implementing the strategy. This report provides an update reflecting progress as of January 2014.

  3. Instrumentation Cables Test Plan

    Energy Technology Data Exchange (ETDEWEB)

    Muna, Alice Baca [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); LaFleur, Chris Bensdotter [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-10-01

    A fire at a nuclear power plant (NPP) has the potential to damage structures, systems, and components important to safety, if not promptly detected and suppressed. At Browns Ferry Nuclear Power Plant on March 22, 1975, a fire in the reactor building damaged electrical power and control systems. Damage to instrumentation cables impeded the function of both normal and standby reactor coolant systems, and degraded the operators’ plant monitoring capability. This event resulted in additional NRC involvement with utilities to ensure that NPPs are properly protected from fire as intended by the NRC principle design criteria (i.e., general design criteria 3, Fire Protection). Current guidance and methods for both deterministic and performance based approaches typically make conservative (bounding) assumptions regarding the fire-induced failure modes of instrumentation cables and those failure modes effects on component and system response. Numerous fire testing programs have been conducted in the past to evaluate the failure modes and effects of electrical cables exposed to severe thermal conditions. However, that testing has primarily focused on control circuits with only a limited number of tests performed on instrumentation circuits. In 2001, the Nuclear Energy Institute (NEI) and the Electric Power Research Institute (EPRI) conducted a series of cable fire tests designed to address specific aspects of the cable failure and circuit fault issues of concern1. The NRC was invited to observe and participate in that program. The NRC sponsored Sandia National Laboratories to support this participation, whom among other things, added a 4-20 mA instrumentation circuit and instrumentation cabling to six of the tests. Although limited, one insight drawn from those instrumentation circuits tests was that the failure characteristics appeared to depend on the cable insulation material. The results showed that for thermoset insulated cables, the instrument reading tended to drift

  4. Virtual Sensor Test Instrumentation

    Science.gov (United States)

    Wang, Roy

    2011-01-01

    Virtual Sensor Test Instrumentation is based on the concept of smart sensor technology for testing with intelligence needed to perform sell-diagnosis of health, and to participate in a hierarchy of health determination at sensor, process, and system levels. A virtual sensor test instrumentation consists of five elements: (1) a common sensor interface, (2) microprocessor, (3) wireless interface, (4) signal conditioning and ADC/DAC (analog-to-digital conversion/ digital-to-analog conversion), and (5) onboard EEPROM (electrically erasable programmable read-only memory) for metadata storage and executable software to create powerful, scalable, reconfigurable, and reliable embedded and distributed test instruments. In order to maximize the efficient data conversion through the smart sensor node, plug-and-play functionality is required to interface with traditional sensors to enhance their identity and capabilities for data processing and communications. Virtual sensor test instrumentation can be accessible wirelessly via a Network Capable Application Processor (NCAP) or a Smart Transducer Interlace Module (STIM) that may be managed under real-time rule engines for mission-critical applications. The transducer senses the physical quantity being measured and converts it into an electrical signal. The signal is fed to an A/D converter, and is ready for use by the processor to execute functional transformation based on the sensor characteristics stored in a Transducer Electronic Data Sheet (TEDS). Virtual sensor test instrumentation is built upon an open-system architecture with standardized protocol modules/stacks to interface with industry standards and commonly used software. One major benefit for deploying the virtual sensor test instrumentation is the ability, through a plug-and-play common interface, to convert raw sensor data in either analog or digital form, to an IEEE 1451 standard-based smart sensor, which has instructions to program sensors for a wide variety of

  5. Introducing the Adults with Chronic Healthcare Needs (ACHCN) definition and screening instrument: Rationale, supporting evidence and testing.

    Science.gov (United States)

    Gulley, Stephen P; Rasch, Elizabeth K; Altman, Barbara M; Bethell, Christina D; Carle, Adam C; Druss, Benjamin G; Houtrow, Amy J; Reichard, Amanda; Chan, Leighton

    2018-04-01

    Among working age adults in the United States, there is a large, heterogeneous population that requires ongoing and elevated levels of healthcare and related services. At present, there are conflicting approaches to the definition and measurement of this population in health services research. An expert panel was convened by the National Institutes of Health with the objective of developing a population-level definition of Adults with Chronic Healthcare Needs (ACHCN). In addition, the panel developed a screening instrument and methods for its use in health surveys to identify and stratify the population consistently. The panel employed multiple methods over the course of the project, including scoping literature reviews, quantitative analyses from national data sources and cognitive testing. The panel defined the ACHCN population as "Adults (age 18-65) with [1] ongoing physical, cognitive, or mental health conditions or difficulties functioning who [2] need health or related support services of a type or amount beyond that needed by adults of the same sex and similar age." The screener collects information on chronic health conditions, functional difficulties, and elevated use of or unmet need for healthcare services. Adapted from the Maternal and Child Health Bureau definition that identifies Children with Special Healthcare Needs, aligned with the ACS-6 disability measure, and consistent with the HHS Multiple Chronic Condition Framework, this definition and screener provide the research community with a common denominator for the identification of ACHCN. Copyright © 2017 Elsevier Inc. All rights reserved.

  6. Instrumentation to Enhance Advanced Test Reactor Irradiations

    Energy Technology Data Exchange (ETDEWEB)

    J. L. Rempe; D. L. Knudson; K. G. Condie; J. E. Daw; S. C. Taylor

    2009-09-01

    The Department of Energy (DOE) designated the Advanced Test Reactor (ATR) as a National Scientific User Facility (NSUF) in April 2007 to support U.S. leadership in nuclear science and technology. By attracting new research users - universities, laboratories, and industry - the ATR will support basic and applied nuclear research and development, further advancing the nation's energy security needs. A key component of the ATR NSUF effort is to prove new in-pile instrumentation techniques that are capable of providing real-time measurements of key parameters during irradiation. To address this need, an assessment of instrumentation available and under-development at other test reactors has been completed. Based on this review, recommendations are made with respect to what instrumentation is needed at the ATR and a strategy has been developed for obtaining these sensors. Progress toward implementing this strategy is reported in this document. It is anticipated that this report will be updated on an annual basis.

  7. Testing and calibration of geodetic instruments

    Directory of Open Access Journals (Sweden)

    Marek Bajtala

    2007-06-01

    Full Text Available The problem of testing, verification and calibration of length-scales (electronic rangefinders and angle-scales (geodetic instruments. The calibration of coded levelling rods and the systemic calibration of digital levelling instruments. The calibration on linear comparative baseline in a terrain – the elaboration of measured data. The testing of universal measuring instruments in laboratory conditions - specific problems in testing of instruments with the passive reflection. Some knowledge about the calibration of horizontal circles of angle-measuring geodetic instruments.

  8. A test instrument for palliative care.

    NARCIS (Netherlands)

    Adriaansen, M.J.M.; Achterberg, T. van

    2004-01-01

    This article describes a methodological study concerning the development of a test instrument that can be used for measuring the effects of a course in palliative care on registered nurses and licensed practical nurses. This test instrument is comprised of two parts: an expertise and insight test

  9. Advanced Instrumentation for Transient Reactor Testing

    Energy Technology Data Exchange (ETDEWEB)

    Corradini, Michael L.; Anderson, Mark; Imel, George; Blue, Tom; Roberts, Jeremy; Davis, Kurt

    2018-01-31

    Transient testing involves placing fuel or material into the core of specialized materials test reactors that are capable of simulating a range of design basis accidents, including reactivity insertion accidents, that require the reactor produce short bursts of intense highpower neutron flux and gamma radiation. Testing fuel behavior in a prototypic neutron environment under high-power, accident-simulation conditions is a key step in licensing nuclear fuels for use in existing and future nuclear power plants. Transient testing of nuclear fuels is needed to develop and prove the safety basis for advanced reactors and fuels. In addition, modern fuel development and design increasingly relies on modeling and simulation efforts that must be informed and validated using specially designed material performance separate effects studies. These studies will require experimental facilities that are able to support variable scale, highly instrumented tests providing data that have appropriate spatial and temporal resolution. Finally, there are efforts now underway to develop advanced light water reactor (LWR) fuels with enhanced performance and accident tolerance. These advanced reactor designs will also require new fuel types. These new fuels need to be tested in a controlled environment in order to learn how they respond to accident conditions. For these applications, transient reactor testing is needed to help design fuels with improved performance. In order to maximize the value of transient testing, there is a need for in-situ transient realtime imaging technology (e.g., the neutron detection and imaging system like the hodoscope) to see fuel motion during rapid transient excursions with a higher degree of spatial and temporal resolution and accuracy. There also exists a need for new small, compact local sensors and instrumentation that are capable of collecting data during transients (e.g., local displacements, temperatures, thermal conductivity, neutron flux, etc.).

  10. Virtual Sensor Test Instrumentation, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — Mobitrum has started the development of virtual sensor test instrumentation in Phase I for characterization and measurement of ground testing of propulsion systems....

  11. Methods and instruments for materials testing

    Science.gov (United States)

    Hansma, Paul (Inventor); Drake, Barney (Inventor); Rehn, Douglas (Inventor); Adams, Jonathan (Inventor); Lulejian, Jason (Inventor)

    2011-01-01

    Methods and instruments for characterizing a material, such as the properties of bone in a living human subject, using a test probe constructed for insertion into the material and a reference probe aligned with the test probe in a housing. The housing is hand held or placed so that the reference probe contacts the surface of the material under pressure applied either by hand or by the weight of the housing. The test probe is inserted into the material to indent the material while maintaining the reference probe substantially under the hand pressure or weight of the housing allowing evaluation of a property of the material related to indentation of the material by the probe. Force can be generated by a voice coil in a magnet structure to the end of which the test probe is connected and supported in the magnet structure by a flexure, opposing flexures, a linear translation stage, or a linear bearing. Optionally, a measurement unit containing the test probe and reference probe is connected to a base unit with a wireless connection, allowing in the field material testing.

  12. Water NSTF Design, Instrumentation, and Test Planning

    Energy Technology Data Exchange (ETDEWEB)

    Lisowski, Darius D.; Gerardi, Craig D.; Hu, Rui; Kilsdonk, Dennis J.; Bremer, Nathan C.; Lomperski, Stephen W.; Kraus, Adam R.; Bucknor, Matthew D.; Lv, Qiuping; Farmer, Mitchell T.

    2017-08-01

    variations and off-normal configurations. The facility design follows, including as-built dimensions and specifications of the various mechanical and liquid systems, design choices for the test section, water storage tank, and network piping. Specifications of the instrumentation suite are then presented, along with specific information on performance windows, measurement uncertainties, and installation locations. Finally, descriptions of the control systems and heat removal networks are provided, which have been engineered to support precise quantification of energy balances and facilitate well-controlled test operations.

  13. Instrumentation Methodology for Automobile Crash Testing

    Science.gov (United States)

    1974-08-01

    Principal characteristics of existing data acquisition practices and instrumentation methodologies have been reviewed to identify differences which are responsible for difficulties in comparing and interpreting structural crash test data. Recommendat...

  14. Radiation protection instrumentation test and calibration

    International Nuclear Information System (INIS)

    Selby, J.M.; Larson, H.V.; Bartlett, W.T.; Mulhern, O.R.; Fleming, D.M.

    1978-01-01

    The operational requirements of radiation protection instrumentation are set forth in the recommendations of various commissions and committees. Additionally, the user may establish the need for different or more restrictive requirements. The ability to meet these requirements will depend not only on the instrument capabilities but also on periodic recalibrations, preventative maintenance and testing of the instruments. A new standard, ANSI N323, ''Radiation Protection Instrumentation Test and Calibration'', has been prepared and approved for use in the USA. This standard establishes calibration methods for portable radiation protection instruments used for detection and measurement of levels of ionizing radiation fields or levels of radioactive surface contamination. Included within the scope of this standard are conditions, equipment and techniques for calibration, as well as the degree of precision and accuracy required. The salient points of the new standard will be presented in the paper. The nature of improvements at our laboratory required by the standard will be discussed. (author)

  15. Instrumentation and test gear circuits manual

    CERN Document Server

    Marston, R M

    2013-01-01

    Instrumentation and Test Gear Circuits Manual provides diagrams, graphs, tables, and discussions of several types of practical circuits. The practical circuits covered in this book include attenuators, bridges, scope trace doublers, timebases, and digital frequency meters. Chapter 1 discusses the basic instrumentation and test gear principles. Chapter 2 deals with the design of passive attenuators, and Chapter 3 with passive and active filter circuits. The subsequent chapters tackle 'bridge' circuits, analogue and digital metering techniques and circuitry, signal and waveform generation, and p

  16. Subsystem Testing and Flight Test Instrumentation.

    Science.gov (United States)

    1981-04-01

    fonctionnement dui moteur . Les deux versions, 6colo ot appui tactique do l’avion ALPHAJET ont des form.. do no: diff~rentes (planche 1). Grace A une 6tude...parambtres habituela de vol. et notamnment ceux repr~sentant lea performances (r~gime ro- tr-r, r~gimes moteurs , temp ~ratures mnoteurs, couples, vitesse...MISS DISTANCE INDICATOR 4 by T.W.Chubb t0 COMPATIBILITE DU MOTEUR AVEC LES AUTRES SYSTEMES DE L’AVION par J.Conche I I FUEL SYSTEM TESTING AND TEST

  17. Aerodynamics support of research instrument development

    Science.gov (United States)

    Miller, L. Scott

    1990-09-01

    A new velocimetry system is currently being developed at NASA LaRC. The device, known as a Doppler global velocimeter (DGV), can record three velocity components within a plane simultaneously and in near real time. To make measurements the DGV, like many other velocimetry systems, relies on the scattering of light from numerous small particles in a flow field. The particles or seeds are illuminated by a sheet of laser light and viewed by two CCD cameras. The scattered light from the particles will have a frequency which is a function of the source laser light frequency, the viewing angle, and most importantly the seed velocities. By determining the scattered light intensity the velocity can be measured at all points within the light sheet simultaneously. Upon completion of DGV component construction and initial check out a series of tests in the Basic Aerodynamic Research (wind) Tunnel (BART) are scheduled to verify instrument operation and accuracy. If the results are satisfactory, application of the DGV to flight measurements on the F-18 High Alpha Research Vehicle (HARV) are planned. The DGV verification test in the BART facility will utilize a 75 degree swept delta wing model. A major task undertaken this summer included evaluation of previous results for this model. A specific series of tests matching exactly the previous tests and exploring new DGV capabilities were developed and suggested. Another task undertaken was to study DGV system installation possibilities in the F-18 HARV aircraft. In addition, a simple seeding system modification was developed and utilized to make Particle Imaging Velocimetry (PIV) measurements in the BART facility.

  18. Void fraction instrument acceptance test procedure

    International Nuclear Information System (INIS)

    Pearce, K.L.

    1994-01-01

    This acceptance test procedure (ATP) was written to test the void fraction instrument (VFI) and verify that the unit is ready for field service. The procedure verifies that the mechanical and electrical features (not specifically addressed in the software ATP) and software alarms are operating as designed

  19. FMIT test-end instrumentation conceptual design

    International Nuclear Information System (INIS)

    Fuller, J.L.

    1984-08-01

    FMIT test-end measurement techniques and instrumentation concepts for deuteron beam control, test-end device protection, test cell radiation field characterization, lithium jet performance monitoring, and in-situ off-line target testing and examination are described. The test-end refers to the beam line-target-test assembly interface area inside the test cell, but TEI includes measurements inside and outside the cell. The measurement requirements are briefly reviewed and referenced. The sometimes severe environmental limitations are discussed. Where feasible, multifunctional systems have been configured. Special facility features have been minimized

  20. Standard practice for instrumented indentation testing

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2007-01-01

    1.1 This practice defines the basic steps of Instrumented Indentation Testing (IIT) and establishes the requirements, accuracies, and capabilities needed by an instrument to successfully perform the test and produce the data that can be used for the determination of indentation hardness and other material characteristics. IIT is a mechanical test that measures the response of a material to the imposed stress and strain of a shaped indenter by forcing the indenter into a material and monitoring the force on, and displacement of, the indenter as a function of time during the full loading-unloading test cycle. 1.2 The operational features of an IIT instrument, as well as requirements for Instrument Verification Annex A1), Standardized Reference Blocks (Annex A2) and Indenter Requirements (Annex A3) are defined. This practice is not intended to be a complete purchase specification for an IIT instrument. 1.3 With the exception of the non-mandatory Appendix X4, this practice does not define the analysis necessary...

  1. Progress in the Instrumented Charpy Impact Test

    OpenAIRE

    Toshiro, KOBAYASHI; Department of Production Systems Engineering, Toyohashi University of Technology

    2002-01-01

    It has passed one century since French G. Charpy proposed the Charpy impact test in 1901. Instrumented impact test recording load history during fracture has been attempted since 1920's. It has become possible to obtain various information from this method. However, succeeding development of fracture mechanics has made it also as a qualitative screening test. To obtain quantitative fracture toughness parameters from this method, therefore, has been desired eagerly. The author developed succes...

  2. In situ viscometer instrument acceptance test report

    International Nuclear Information System (INIS)

    Pearce, K.L.

    1994-01-01

    This document presents the results of the acceptance test for the mechanical and electrical features (not specifically addressed by the software ATP) of the viscometer instrument. This document and the ATP satisfy the requirements in EP-4.1, ''Design Verification Requirements.'' The selected mode of design verification is qualification testing. The testing described in this document verifies that the mechanical and electrical features are operating as designed and that the unit is ready for field service

  3. Development process and psychometric testing of foot health assessment instrument.

    Science.gov (United States)

    Stolt, Minna; Suhonen, Riitta; Puukka, Pauli; Viitanen, Matti; Voutilainen, Päivi; Leino-Kilpi, Helena

    2013-05-01

    To describe the development process of the foot health assessment instrument for the assessment of foot health in older people and to evaluate the psychometric properties of the foot health assessment instrument. In clinical nursing, assessment of foot health and recognition of foot problems in older people is fundamental for maintain older persons' independent functional ability. However, valid and reliable nurse-administered foot health assessment instruments are lacking. A cross-sectional methodological design. The foot health assessment instrument was developed in 2008-2011 based on a literature review and expertise in podiatry and nursing. Content validity was evaluated in four expert panels. Inter-rater reliability between nurses' and researcher (MS) assessments was evaluated in the pilot test and in the empirical testing of the instrument with a sample of visiting home nurses. Inter-rater reliability was calculated with Cohen's kappa, internal consistency reliability was examined with Cronbach's alpha coefficients and item analysis, and construct validity was evaluated by principal component analysis with Varimax rotation and confirmatory factor analysis. Content validity was guaranteed by the expert analyses. Inter-rater reliability improved after pilot test. The Cronbach's alpha coefficient for the total foot health assessment instrument was satisfactory. Item-to-total correlations varied between but most of them were acceptable. Principal component analysis and confirmatory factor analysis supported the four component structure of the foot health assessment instrument. The 23-item foot health assessment instrument showed preliminary acceptable psychometric properties. However, further modifications and testing are needed to strengthen the psychometric properties of the foot health assessment instrument. The existence of a foot health assessment instrument and its application would considerably improve the assessment of foot health in daily nursing

  4. Technical testing of portable isotope identification instruments

    International Nuclear Information System (INIS)

    Smith, D.E.

    2001-01-01

    . First generation portable isotope identifiers were identified and evaluated by U.S. Customs. Instruments from five vendors were put through a battery of tests according to delineated test procedures. The tests fell into five categories: Basic operation verification; Medical isotope identification; Individual isotope identification; Isotope pair identification; Dose rate calculation. The tests can be summarized as an initial verification of correct instrument operation (including whatever calibration procedure was specified by the vendor), followed by three different isotope identification tests designed to verify the instrument's ability to correctly identify 19 isotopes specified by U.S. Customs. The final test determined each instrument's ability to correctly display the dose rate from a wide energy range of gamma emitters. The individual isotope identification test and the isotope pair identification test were performed with three types of intervening shielding. The first of these three types used the minimum packaging needed for safe source handling and was, in general, thin plastic. This type of shielding is virtually identical to a bare radiation source. The second type of shielding used 2.7 mm of steel to simulate the wall of a typical transportainer (or sea-tainer). The third type of shielding used 6.94 mm of lead to simulate typical industrial packaging or, perhaps, an attempt by the shipper to conceal the source without unduly increasing the weight of the shipment. The isotopes tested were broadly categorized as: Special nuclear material (SNM), Medical, and Industrial. These included 17 gamma emitters, 1 beta emitter, and 1 neutron emitter. Each instrument was subjected to the following testing regimen: First, each instrument was calibrated according to vendor's procedures. Instrument size and weight were recorded. Next, the instrument's response to medical isotopes in their usual shipping containers was measured. This represents the most commonly occurring

  5. Concept mapping instrumental support for problem solving

    NARCIS (Netherlands)

    Stoyanov, S.; Stoyanov, Slavi; Kommers, Petrus A.M.

    2008-01-01

    The main theoretical position of this paper is that it is the explicit problem-solving support in concept mapping software that produces a stronger effect in problem-solving performance than the implicit support afforded by the graphical functionality of concept mapping software. Explicit

  6. Periodic testing of instrumentation and control systems

    International Nuclear Information System (INIS)

    Raimondo, E.

    1989-01-01

    During normal operation, protection systems are on standby and possible failure of system components may therefore go undetected. Their ability to function as intended, should they be initiated after a long period of time, is thus questionable. For this reason, French as well as international rules require that protection systems be subjected to periodic tests. Because of the equipment available when the units in the French 900-MW(electric) series were designed, the instrumentation and control systems were equipped with manual periodic test systems. This was the case with the reactor protection system (RPS) periodic test equipment where the manual procedures relied on the manipulation of a large number of switches and push buttons. This manual test equipment has been successfully replaced on the 28 units in the French 900-MW(electric) series by the automatic tester discussed in this paper

  7. Design of the Local Instrument for KSTAR Gravity Support

    International Nuclear Information System (INIS)

    Her, N. I.; Kim, H. K.; Kim, Y. O.; Sa, J. W.; Kim, G. H.; Kim, K. M.; Park, Y. M.; Hong, G. H.; Choi, C. H.; Bak, J. S.

    2005-01-01

    should be operated without malfunction in the environment of cryogenic temperature up to 4.5 K and high magnetic field up to 2T(Tesla). In this study, the design of local instrumentation system for gravity support and its prototype testing results are summarized

  8. Body support testing and rating.

    Science.gov (United States)

    Rogers, J E

    1992-08-01

    testing can be measured, and claims can be made for shoes and sneakers. Where impact loads and shear forces are paramount, the score must comprise appropriate parameters. Similarly, amputee distal stump relief as a percentage of worst case could be specified by the fitter. Iliac crest relief as a percentage of worst case can also be specified by the fitter. In all instances the score is not a subjective rating but one that can be measured correctly. All body support products can be given an REF, C value, and score as well as other qualifying values where appropriate instrumentation and sufficient subject sampling is used.

  9. Standard test method for instrumented impact testing of metallic materials

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2009-01-01

    1.1 This standard establishes the requirements for performing instrumented Charpy V-Notch (CVN) and instrumented Miniaturized Charpy V-Notch (MCVN) impact tests on metallic materials. This method, which is based on experience developed testing steels, provides further information (in addition to the total absorbed energy) on the fracture behavior of the tested materials. Minimum requirements are given for measurement and recording equipment such that similar sensitivity and comparable total absorbed energy measurements to those obtained in Test Methods E 23 and E 2248 are achieved. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  10. Acoustic emission measurement during instrumented impact tests

    International Nuclear Information System (INIS)

    Crostack, H.A.; Engelhardt, A.H.

    1983-01-01

    Results of instrumented impact tests are discussed. On the one hand the development of the loading process at the hammer tup was recorded by means of a piezoelectric transducer. This instrumentation supplied a better representation of the load versus time than the conventional strain gauges. On the other hand the different types of acoustic emission occurring during a test could be separated. The acoustic emission released at the impact of the hammer onto the specimen is of lower frequency and its spectrum is strongly decreasing with increasing frequency. Plastic deformation also emits signals of lower frequency that are of quasi-continuous character. Both signal types can be discriminated by filtering. As a consequence typical burst signal were received afterwards that can be correlated with crack propagation. Their spectra exhibit considerable portions up to about 1.9 MHz. The development in time of the burst signals points to the kind of crack propagation resp. its sequence of appearance. However, definitive comparison between load and acoustic emission should become possible, only when the disadvantages of the common load measurement can be reduced, e.g. by determining the load directly at the specimen instead of the hammer tup

  11. Assessing the quality of decision support technologies using the International Patient Decision Aid Standards instrument (IPDASi).

    NARCIS (Netherlands)

    Elwyn, G.; O'Connor, A.M.; Bennett, C.; Newcombe, R.G.; Politi, M.; Durand, M.A.; Drake, E.; Joseph-Williams, N.; Khangura, S.; Saarimaki, A.; Sivell, S.; Stiel, M.; Bernstein, S.J.; Col, N.; Coulter, A.; Eden, K.; Harter, M.; Rovner, M.H.; Moumjid, N.; Stacey, D.; Thomson, R.; Whelan, T.; Weijden, G.D.E.M. van der; Edwards, A.

    2009-01-01

    OBJECTIVES: To describe the development, validation and inter-rater reliability of an instrument to measure the quality of patient decision support technologies (decision aids). DESIGN: Scale development study, involving construct, item and scale development, validation and reliability testing.

  12. PASSCAL Instrument Center Support for Cryoseismology: Methodologies, Challenges, Development and Instrumentation

    Science.gov (United States)

    Beaudoin, B. C.; Anderson, K. R.; Bilek, S. L.; Carpenter, P.; Childs, D.; Chung, P.; Huerta, A. D.; Lingutla, N.; Nikolaus, K.; Winberry, J. P.

    2017-12-01

    Remote portable seismic stations are, in most cases, constrained by logistics and cost. High latitude operations introduce environmental, technical and logistical challenges that require substantially more engineering work to ensure robust, high quality data return. Since 2006, IRIS PASSCAL has been funded by NSF to develop, deploy, and maintain a pool of polar specific seismic stations. At roughly the same time, PASSCAL began supporting experiments specifically targeting glacier dynamics such as the mechanisms of subglacial hydrology, basal shear stress, ice stream stick slip mechanisms, and glacier seismicity. Although much of the development for high-latitude deployments was directly applicable to cryoseismology, these new experiments introduced a unique series of challenges including high ablation, standing water, and moving stations. Our polar development objectives have focused on: Reducing station power requirements, size and weight; Extending the operational temperature of a station; Simplifying logistics; Engineering solutions that are cost effective, manufacturable, serviceable and reusable; And, developing high-latitude communications for both state-of-health and data transmission. To these ends, PASSCAL continues testing new power storage technology, refining established power systems for lighter and smaller power banks, and exploring telemetry solutions to increase high-bandwidth communication options and abilities for remote seismic stations. Further enhancing PASSCAL's ability to support cryoseismology is a recent NSF funded collaborative effort lead by Central Washing University joined by IRIS and New Mexico Tech to build a Geophysical Earth Observatory for Ice Covered Environments (GEOICE). The GEOICE instrument, power system and other integrated ancillary components are designed to require minimal installation time and logistical load (i.e., size and weight), while maximizing ease-of-use in the field and optimizing costs of instrumentation and

  13. Instrument Rating Practical Test Standards for Airplane, Helicopter, Airship

    Science.gov (United States)

    1994-10-01

    The Instrument Rating Practical Test Standards (PTS) book has : been published by the Federal Aviation Administration (FAA) to : establish the standards for the instrument rating practical test for : airplanes, helicopters, and airships. FAA inspecto...

  14. Large coil test facility instrumentation system design

    International Nuclear Information System (INIS)

    Walstrom, P.L.; Fletcher, W.M.; Goddard, J.S.; Murphy, J.L.

    1979-01-01

    The design of the instrumentation system for the Large Coil Test Facility (LCTF) is described. Sensors are divided into two categories: coil diagnostic sensors, installed in the test coils; and facility sensors, installed in the various systems of the test facility in order to monitor their performance. After signal conditioning, data from the ''fast'' channels are multiplexed, digitized, and stored in four microcomputer systems programmed to be used in a ring buffer mode to record data before and after receipt of a random trigger from the normal zone detection circuitry. ''Slow'' channels are digitized by a scanner and buffered by a microcomputer. Selected data channels are continuously displayed on digital or recorded on strip chart recorders. The microcomputer systems are interfaced to a central minicomputer system for display and archival storage. Facility variables are digitized by a separate scanner system. Certain critical fault variables are compared with set point values, and if they are out of range, cause a programmable logic controller to initiate an emergency coil energy dump. 2 refs

  15. Thirty Years Supporting Portable Arrays: The IRIS Passcal Instrument Center

    Science.gov (United States)

    Beaudoin, B. C.; Anderson, K. R.; Bilek, S. L.; Woodward, R.

    2014-12-01

    Thirty years have passed since establishment of the IRIS Program for the Array Seismic Studies of the Continental Lithosphere (PASSCAL). PASSCAL was part of a coordinated plan proposed to the National Science Foundation (NSF) defining the instrumentation, data collection and management structure to support a wide range of research in seismology. The PASSCAL program has surpassed the early goal of 6000 data acquisition channels with a current inventory of instrumentation capable of imaging from the near surface to the inner core. Here we present the evolution of the PASSCAL program from instrument depot to full service community resource. PASSCAL has supported close to 1100 PI driven seismic experiments since its inception. Instruments from PASSCAL have covered the globe and have contributed over 7400 SEED stations and 242 assembled data sets to the IRIS Data Management Center in Seattle. Since the combination in 1998 of the Stanford and Lamont instrument centers into the single PASSCAL Instrument Center (PIC) at New Mexico Tech, the facility has grown in scope by adding the EarthScope Array Operations Facility in 2005, the incorporation of the EarthScope Flexible Array, and a Polar support group in 2006. The polar support group enhances portable seismic experiments in extremely harsh polar environments and also extends to special projects such as the Greenland Ice Sheet Monitoring Network (GLISN) and the recent development effort for Geophysical Earth Observatory for Ice Covered Environments (GEOICE). Through these support efforts the PIC has established itself as a resource for field practices, engineered solutions for autonomous seismic stations, and a pioneer in successful seismic recording in polar environments. We are on the cusp of a new generation of instrumentation driven in part by the academic community's desire to record unaliased wavefields in multiple frequency bands and industry's interest in utilizing lower frequency data. As part of the recently

  16. Quality of prenatal care questionnaire: instrument development and testing

    Science.gov (United States)

    2014-01-01

    Background Utilization indices exist to measure quantity of prenatal care, but currently there is no published instrument to assess quality of prenatal care. The purpose of this study was to develop and test a new instrument, the Quality of Prenatal Care Questionnaire (QPCQ). Methods Data for this instrument development study were collected in five Canadian cities. Items for the QPCQ were generated through interviews with 40 pregnant women and 40 health care providers and a review of prenatal care guidelines, followed by assessment of content validity and rating of importance of items. The preliminary 100-item QPCQ was administered to 422 postpartum women to conduct item reduction using exploratory factor analysis. The final 46-item version of the QPCQ was then administered to another 422 postpartum women to establish its construct validity, and internal consistency and test-retest reliability. Results Exploratory factor analysis reduced the QPCQ to 46 items, factored into 6 subscales, which subsequently were validated by confirmatory factor analysis. Construct validity was also demonstrated using a hypothesis testing approach; there was a significant positive association between women’s ratings of the quality of prenatal care and their satisfaction with care (r = 0.81). Convergent validity was demonstrated by a significant positive correlation (r = 0.63) between the “Support and Respect” subscale of the QPCQ and the “Respectfulness/Emotional Support” subscale of the Prenatal Interpersonal Processes of Care instrument. The overall QPCQ had acceptable internal consistency reliability (Cronbach’s alpha = 0.96), as did each of the subscales. The test-retest reliability result (Intra-class correlation coefficient = 0.88) indicated stability of the instrument on repeat administration approximately one week later. Temporal stability testing confirmed that women’s ratings of their quality of prenatal care did not change as a result of giving

  17. A Critical Review of Instruments Measuring Breastfeeding Attitudes, Knowledge, and Social Support.

    Science.gov (United States)

    Casal, Corrine S; Lei, Ann; Young, Sera L; Tuthill, Emily L

    2017-02-01

    Breastfeeding provides beneficial health outcomes for infants and their mothers, and increasing its practice is a national priority in many countries. Despite increasing support to exclusively breastfeed, the prevalence at 6 months remains low. Breastfeeding behavior is influenced by a myriad of determinants, including breastfeeding attitudes, knowledge, and social support. Effective measurement of these determinants is critical to provide optimal support for women throughout the breastfeeding period. However, there are a multitude of available instruments measuring these constructs, which makes identification of an appropriate instrument challenging. Research aim: Our aim was to identify and critically examine the existing instruments measuring breastfeeding attitudes, knowledge, and social support. A total of 16 instruments was identified. Each instrument's purpose, theoretical underpinnings, and validity were analyzed. An overview, validation and adaptation for use in other settings was assessed for each instrument. Depth of reporting and validation testing differed greatly between instruments. Content, construct, and predictive validity were present for most but not all scales. When selecting and adapting instruments, attention should be paid to domains within the scale, number of items, and adaptation.

  18. Energy Production from Biogas: Competitiveness and Support Instruments in Latvia

    OpenAIRE

    Klāvs G.; Kundziņa A.; Kudrenickis I.

    2016-01-01

    Use of renewable energy sources (RES) might be one of the key factors for the triple win-win: improving energy supply security, promoting local economic development, and reducing greenhouse gas emissions. The authors ex-post evaluate the impact of two main support instruments applied in 2010-2014 – the investment support (IS) and the feed-in tariff (FIT) – on the economic viability of small scale (up to 2MWel) biogas unit. The results indicate that the electricity production cost in biogas ut...

  19. Enhanced In-Pile Instrumentation at the Advanced Test Reactor

    Energy Technology Data Exchange (ETDEWEB)

    J. Rempe; D. Knudson; J. Daw; T. Unruh; B. Chase; K. Condie

    2011-06-01

    Many of the sensors deployed at materials and test reactors cannot withstand the high flux/high temperature test conditions often requested by users at U.S. test reactors, such as the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL). To address this issue, an instrumentation development effort was initiated as part of the ATR National Scientific User Facility (NSUF) in 2007 to support the development and deployment of enhanced in-pile sensors. This paper reports results from this effort. Specifically, this paper identifies the types of sensors currently available to support in-pile irradiations and those sensors currently available to ATR users. Accomplishments from new sensor technology deployment efforts are highlighted by describing new temperature and thermal conductivity sensors now available to ATR users. Efforts to deploy enhanced in-pile sensors for detecting elongation and real-time flux detectors are also reported, and recently-initiated research to evaluate the viability of advanced technologies to provide enhanced accuracy for measuring key parameters during irradiation testing are noted.

  20. Energy Production from Biogas: Competitiveness and Support Instruments in Latvia

    Science.gov (United States)

    Klāvs, G.; Kundziņa, A.; Kudrenickis, I.

    2016-10-01

    Use of renewable energy sources (RES) might be one of the key factors for the triple win-win: improving energy supply security, promoting local economic development, and reducing greenhouse gas emissions. The authors ex-post evaluate the impact of two main support instruments applied in 2010-2014 - the investment support (IS) and the feed-in tariff (FIT) - on the economic viability of small scale (up to 2MWel) biogas unit. The results indicate that the electricity production cost in biogas utility roughly corresponds to the historical FIT regarding electricity production using RES. However, if in addition to the FIT the IS is provided, the analysis shows that the practice of combining both the above-mentioned instruments is not optimal because too high total support (overcompensation) is provided for a biogas utility developer. In a long-term perspective, the latter gives wrong signals for investments in new technologies and also creates unequal competition in the RES electricity market. To provide optimal biogas utilisation, it is necessary to consider several options. Both on-site production of electricity and upgrading to biomethane for use in a low pressure gas distribution network are simulated by the cost estimation model. The authors' estimates show that upgrading for use in a gas distribution network should be particularly considered taking into account the already existing infrastructure and technologies. This option requires lower support compared to support for electricity production in small-scale biogas utilities.

  1. Energy Production from Biogas: Competitiveness and Support Instruments in Latvia

    Directory of Open Access Journals (Sweden)

    Klāvs G.

    2016-10-01

    Full Text Available Use of renewable energy sources (RES might be one of the key factors for the triple win-win: improving energy supply security, promoting local economic development, and reducing greenhouse gas emissions. The authors ex-post evaluate the impact of two main support instruments applied in 2010-2014 – the investment support (IS and the feed-in tariff (FIT – on the economic viability of small scale (up to 2MWel biogas unit. The results indicate that the electricity production cost in biogas utility roughly corresponds to the historical FIT regarding electricity production using RES. However, if in addition to the FIT the IS is provided, the analysis shows that the practice of combining both the above-mentioned instruments is not optimal because too high total support (overcompensation is provided for a biogas utility developer. In a long-term perspective, the latter gives wrong signals for investments in new technologies and also creates unequal competition in the RES electricity market. To provide optimal biogas utilisation, it is necessary to consider several options. Both on-site production of electricity and upgrading to biomethane for use in a low pressure gas distribution network are simulated by the cost estimation model. The authors’ estimates show that upgrading for use in a gas distribution network should be particularly considered taking into account the already existing infrastructure and technologies. This option requires lower support compared to support for electricity production in small-scale biogas utilities.

  2. Flight Test Guide (Part 61 Revised): Instrument Pilot: Helicopter.

    Science.gov (United States)

    Federal Aviation Administration (DOT), Washington, DC. Flight Standards Service.

    The guide provides an outline of the skills required to pass the flight test for an Instrument Pilot Helicopter Rating under Part 61 (revised) of Federal Aviation Regulations. General procedures for flight tests are described and the following pilot operations outlined: maneuvering by reference to instruments, IFR navigation, instrument…

  3. FMIT test-end instrumentation systems scoping study

    International Nuclear Information System (INIS)

    Fuller, J.L.; Dixon, N.E.; Sheen, E.M.

    1982-06-01

    For the Fusion Materials Irradiation Test facility (FMIT), the high power density of the accelerated deuteron beam and the unique nature of the liquid lithium target underscore the need for sensitive, fast and reliable test-end diagnostic instrumentation. The intense radiation environment in the test cell places severe limits on candidate systems, as to a lesser degree do thermal and lithium compatibility factors. A beam-target diagnostic station at 180 in the HEBT can facilitate source emission and spot-on-target imaging. Analyses support the feasibility of several candidate imaging systems. Incorporation of electromagnetic and electrostatic beam position detectors as part of the target assembly, as previously proposed, should also be feasible. The possibilities for on-line, real-time ultrasonic/acoustic target diagnosis are favorable. The use of redundant thermocouple and ion detector test assembly beam location detectors is also supported because of the possible problems with thermocouples in the intense 14-MeV neutron field and the simplicity of the ion detectors

  4. Falsification Testing of Instrumental Variables Methods for Comparative Effectiveness Research.

    Science.gov (United States)

    Pizer, Steven D

    2016-04-01

    To demonstrate how falsification tests can be used to evaluate instrumental variables methods applicable to a wide variety of comparative effectiveness research questions. Brief conceptual review of instrumental variables and falsification testing principles and techniques accompanied by an empirical application. Sample STATA code related to the empirical application is provided in the Appendix. Comparative long-term risks of sulfonylureas and thiazolidinediones for management of type 2 diabetes. Outcomes include mortality and hospitalization for an ambulatory care-sensitive condition. Prescribing pattern variations are used as instrumental variables. Falsification testing is an easily computed and powerful way to evaluate the validity of the key assumption underlying instrumental variables analysis. If falsification tests are used, instrumental variables techniques can help answer a multitude of important clinical questions. © Health Research and Educational Trust.

  5. Realistic dynamic stope support testing

    CSIR Research Space (South Africa)

    Ortlepp, WD

    2000-08-01

    Full Text Available mass of 10 000kg from a height of 3 metres to impact at a velocity of 7.7 m/s upon the target ‘rock mass’. The target mass was represented by a discontinuous but compact arrangement of steel-clad concrete blocks which would transmit and disperse... the concentrated impact load downward on to a collapsible roof. Carefully designed, shaped concrete blocks would represent the fractured hangingwall layer of the stope, the stability of which would be determined largely by the support system under test...

  6. Instrument development in support of Falcon and Phebus-FP

    International Nuclear Information System (INIS)

    Bowsher, B.R.; Brunning, J.

    1992-12-01

    This review has been undertaken to identify various on-line instruments and post-test analytical techniques that may improve the quality of data from both the Falcon Integral Test Programme and Phebus-FP. Particular emphasis is placed on the use of in-situ techniques to provide mass-based data on the aerodynamic properties of the aerosol and fission product-surface interactions. The principles of the following techniques are reviewed: cascade impactors, tapered element oscillating microbalance, condensation nucleus counter, Knudsen cell mass spectrometry, diffuse reflectance infrared Fourier transform spectrometry and secondary-ion mass spectrometry. These methods are currently being used in the Falcon experimental programme. (author)

  7. Instrument development in support of Falcon and Phebus-FP

    Energy Technology Data Exchange (ETDEWEB)

    Bowsher, B.R.; Brunning, J.

    1992-12-01

    This review has been undertaken to identify various on-line instruments and post-test analytical techniques that may improve the quality of data from both the Falcon Integral Test Programme and Phebus-FP. Particular emphasis is placed on the use of in-situ techniques to provide mass-based data on the aerodynamic properties of the aerosol and fission product-surface interactions. The principles of the following techniques are reviewed: cascade impactors, tapered element oscillating microbalance, condensation nucleus counter, Knudsen cell mass spectrometry, diffuse reflectance infrared Fourier transform spectrometry and secondary-ion mass spectrometry. These methods are currently being used in the Falcon experimental programme. (author).

  8. International standardization of instruments for neutron irradiation tests

    International Nuclear Information System (INIS)

    Tanimoto, Masataka; Shibata, Akira; Nakamura, Jinichi; Tsuchiya, Kunihiko; Cho, M.; Lee, C.; Park, S.; Choo, K.

    2012-01-01

    The JMTR in JAEA and HANARO in KAERI are the foremost testing/research reactors in the world and these are expected to contribute to many nuclear fields. As a part of instrument development in irradiation field, information exchange of instruments started from 2010 under the cooperation agreements between KAERI and JAEA. The instruments developed in JMTR and HANARO are introduced and cooperation experiments as future plan are discussed for international standardization. (author)

  9. USDI DCS technical support: Mississippi Test Facility

    Science.gov (United States)

    Preble, D. M.

    1975-01-01

    The objective of the technical support effort is to provide hardware and data processing support to DCS users so that application of the system may be simply and effectively implemented. Technical support at Mississippi Test Facility (MTF) is concerned primarily with on-site hardware. The first objective of the DCP hardware support was to assure that standard measuring apparatus and techniques used by the USGS could be adapted to the DCS. The second objective was to try to standardize the miscellaneous variety of parameters into a standard instrument set. The third objective was to provide the necessary accessories to simplify the use and complement the capabilities of the DCP. The standard USGS sites have been interfaced and are presently operating. These sites are stream gauge, ground water level and line operated quality of water. Evapotranspiration, meteorological and battery operated quality of water sites are planned for near future DCP operation. Three accessories which are under test or development are the Chu antenna, solar power supply and add-on memory. The DCP has proven to be relatively easy to interface with many monitors. The large antenna is awkward to install and transport. The DCS has met the original requirements well; it has and is proving that an operation, satellite-based data collection system is feasible.

  10. Instrumentation

    International Nuclear Information System (INIS)

    Decreton, M.

    2001-01-01

    SCK-CEN's research and development programme on instrumentation involves the assessment and the development of sensitive measurement systems used within a radiation environment. Particular emphasis is on the assessment of optical fibre components and their adaptability to radiation environments. The evaluation of ageing processes of instrumentation in fission plants, the development of specific data evaluation strategies to compensate for ageing induced degradation of sensors and cable performance form part of these activities. In 2000, particular emphasis was on in-core reactor instrumentation applied to fusion, accelerator driven and water-cooled fission reactors. This involved the development of high performance instrumentation for irradiation experiments in the BR2 reactor in support of new instrumentation needs for MYRRHA, and for diagnostic systems for the ITER reactor

  11. Instrumentation

    Energy Technology Data Exchange (ETDEWEB)

    Decreton, M

    2001-04-01

    SCK-CEN's research and development programme on instrumentation involves the assessment and the development of sensitive measurement systems used within a radiation environment. Particular emphasis is on the assessment of optical fibre components and their adaptability to radiation environments. The evaluation of ageing processes of instrumentation in fission plants, the development of specific data evaluation strategies to compensate for ageing induced degradation of sensors and cable performance form part of these activities. In 2000, particular emphasis was on in-core reactor instrumentation applied to fusion, accelerator driven and water-cooled fission reactors. This involved the development of high performance instrumentation for irradiation experiments in the BR2 reactor in support of new instrumentation needs for MYRRHA, and for diagnostic systems for the ITER reactor.

  12. Development of test methodology for dynamic mechanical analysis instrumentation

    Science.gov (United States)

    Allen, V. R.

    1982-01-01

    Dynamic mechanical analysis instrumentation was used for the development of specific test methodology in the determination of engineering parameters of selected materials, esp. plastics and elastomers, over a broad range of temperature with selected environment. The methodology for routine procedures was established with specific attention given to sample geometry, sample size, and mounting techniques. The basic software of the duPont 1090 thermal analyzer was used for data reduction which simplify the theoretical interpretation. Clamps were developed which allowed 'relative' damping during the cure cycle to be measured for the fiber-glass supported resin. The correlation of fracture energy 'toughness' (or impact strength) with the low temperature (glassy) relaxation responses for a 'rubber-modified' epoxy system was negative in result because the low-temperature dispersion mode (-80 C) of the modifier coincided with that of the epoxy matrix, making quantitative comparison unrealistic.

  13. Instrumentation Report No. 3: performance and reliability of instrumentation deployed for the Spent Fuel Test - Climax

    International Nuclear Information System (INIS)

    Patrick, W.C.; Rector, N.L.; Scarafiotti, J.J.

    1984-12-01

    A demonstration of the short-term storage and subsequent retrieval of spent nuclear fuel assemblies was successfully completed at the US Department of Energy's Nevada Test Site. Nearly 1000 instruments were deployed to monitor the temperature of rock, air, and metallic components of the test; displacements and stress changes within the rock mass; radiation dosage to personnel and to the rock; thermal energy input; characteristics of the ventilation airstream; and the operational status of the test. Careful selection, installation, calibration, and maintenance of these instruments ensured the acquisition of about 15.3 x 10 6 high-quality data points. With few exceptions, the performance and reliability of the instrumentation and associated data acquisition system (DAS) were within specified acceptable limits. Details of the performance and reliability of the instrumentation are discussed in this report. 42 figs., 32 tabs

  14. Performance tests for instruments measuring radon activity concentration

    International Nuclear Information System (INIS)

    Beck, T.R.; Buchroeder, H.; Schmidt, V.

    2009-01-01

    Performance tests of electronic instruments measuring the activity concentration of 222 Rn have been carried out with respect to the standard IEC 61577-2. In total, 9 types of instrument operating with ionization chambers or electrostatic collection have been tested for the influence of different climatic and radiological factors on the measurement characteristics. It is concluded that all types of instrument, which are commercially available, are suitable for indoor radon measurements. Because of the dependence on climatic conditions, the outdoor use is partly limited.

  15. THE DYNAMIC BEHAVIOUR OF THE INSTRUMENTED CHARPY TEST

    OpenAIRE

    Mines, R.; Ruiz, C.

    1985-01-01

    The dynamic characteristics of the Charpy test have been studied by means of a Hopkinson bar apparatus and photoelasticity. It is found that this technique permits a clear evaluation of the test results, and is preferable to the standard instrumented pendulum test.

  16. Set of instruments and devices for monitoring supports of vertical shafts in deep mines

    Energy Technology Data Exchange (ETDEWEB)

    Repko, A.A.; Kalinnikov, V.P.; Kozel, A.M.

    1984-07-01

    The characteristics and main specifications are given for the AG-3M mechanical device for measuring shaft wall deviations, the DI-8 converter, the DI-9 concrete deformation meter and the 72-D13 tensodynamometric instrument for measuring contact radial loads on supports. The set of equipment is made up by an SP-11 control panel, an RK-3 switching unit and an RA-2 junction box. Measurements are made from the roof of the hoisting gear or from the cage using the AG-3M device, and measurements with all other instruments are by remote control. A block diagram for the layout of the remote control instruments is given. The RK-3 switching unit allows the operation of 50 DI-9 devices and 50 72-D13 instruments to be monitored. This system is being tested in the shafts of deep mines in the Central Donbass; first results have been favorable.

  17. Teacher Support in Learning: Instrumental and Appraisal Support in Relation to Math Achievement

    Science.gov (United States)

    Wong, Tracy K. Y.; Tao, Xi; Konishi, Chiaki

    2018-01-01

    This study explored the extent to which teachers' instrumental (i.e., tangible aid to promote learning) and appraisal support (i.e., teacher feedback) enhanced students' achievement in mathematics. Participants included 13,950 fifteen-year-old Canadian students who participated in the 2012 Programme for International Student Assessment. Based on…

  18. A Universal Motor Performance Test System Based on Virtual Instrument

    Directory of Open Access Journals (Sweden)

    Wei Li

    2014-09-01

    Full Text Available With the development of technology universal motors play a more and more important role in daily life and production, they have been used in increasingly wide field and the requirements increase gradually. How to control the speed and monitor the real-time temperature of motors are key issues. The cost of motor testing system based on traditional technology platform is very high in many reasons. In the paper a universal motor performance test system which based on virtual instrument is provided. The system achieves the precise control of the current motor speed and completes the measurement of real-time temperature of motor bearing support in order to realize the testing of general-purpose motor property. Experimental result shows that the system can work stability in controlling the speed and monitoring the real-time temperature. It has advantages that traditional using of SCM cannot match in speed, stability, cost and accuracy aspects. Besides it is easy to expand and reconfigure.

  19. Powertrain instrumentation and test systems development, hybridization, electrification

    CERN Document Server

    Paulweber, Michael

    2016-01-01

    The book deals with the increasingly complex test systems for powertrain components and systems giving an overview of the diverse types of test beds for all components of an advanced powertrain focusing on specific topics such as instrumentation, control, simulation, hardware-in-the-loop, automation or test facility management. This book is intended for powertrain (component) development engineers, test bed planners, test bed operators and beginners.

  20. On-site cell field test support program

    Science.gov (United States)

    Staniunas, J. W.; Merten, G. P.

    1982-09-01

    Utility sites for data monitoring were reviewed and selected. Each of these sites will be instrumented and its energy requirements monitored and analyzed for one year prior to the selection of 40 Kilowatt fuel cell field test sites. Analyses in support of the selection of sites for instrumentation shows that many building sectors offered considerable market potential. These sectors include nursing home, health club, restaurant, industrial, hotel/motel and apartment.

  1. Development and testing of the GNSS Instrument System for Multistatic and Occultation Sensing (GISMOS) airborne instrument.

    Science.gov (United States)

    Garrison, J. L.; Ventre, B. D.; Haase, J.; Boehme, M. H.

    2006-12-01

    The GNSS Instrument System for Multistatic and Occultation Sensing (GISMOS) is a new remote sensing system being developed for the HIAPER Gulfstream V aircraft, under support of the National Science Foundation. This system is designed to use occulted and reflected Global Navigation Satellite System (GNSS) signals to retrieve tropospheric water vapor, ocean surface roughness and soil moisture during long duration, high altitude, flights. This presentation will summarize the preliminary design and engineering testing of the GISMOS instruments. Applications of this system to ocean and land reflection measurements and calibration/validation activities for satellite missions, will be emphasized. GISMOS will use five GNSS antennas on the aircraft fuselage. One will be used for precision navigation. Two antennas, one mounted in the window blanks on each side of the fuselage, will be used to track occulting GPS signals. A pair of antennas will be mounted on the bottom of the fuselage to record both the right-hand and left-hand circularly polarized components of the reflected GNSS signal. A GNSS recorder will also sample and record the intermediate frequency (IF) signal from up to three dual- frequency antennas. This would allow simultaneous recording of RHCP and LHCP reflected signals, at both L1 and L2 frequencies, and the direct signal for power and delay calibration. Occultation measurements could also be collected in conjunction with reflection measurements. The automatic gain control (AGC) gain is sampled at 1 Hz, and stored in the data stream, to allow an absolute calibration of power measurements. A software receiver will be used to generate delay-Doppler waveforms from the reflected signals, which can be inverted using a scattering model to estimate the statistics of the reflecting surface. Waveform generation at L2 will be done using the L2C code on the modernized GPS satellites. The software receiver will also allow open-loop tracking of occulted GPS signals

  2. WATCH: Warwick Assessment insTrument for Clinical teacHing: Development and testing.

    Science.gov (United States)

    Haider, Sonia Ijaz; Johnson, Neil; Thistlethwaite, Jill Elizabeth; Fagan, Gay; Bari, Muhammad Furqan

    2015-03-01

    Medical education and teaching skills are core competencies included in the generic curriculum for specialty training. To support the development of these skills, there is need for a validated instrument. This study aims to develop and test an instrument to measure the attributes of specialty trainees as effective teachers. The study was conducted in two phases. In first phase, the content of the instrument was generated from the literature and tested using the Delphi technique. In second phase, the instrument was field tested for validity and reliability using factor analysis and generalizability study. Feasibility was calculated by the time taken to complete the instrument. Acceptability and educational impact were determined by qualitative analysis of written feedback. Attributes of specialty trainees were assessed by clinical supervisors, peers, and students. The Delphi study produced consensus on 15 statements which formed the basis of the instrument. In field study, a total of 415 instruments were completed. Factor analysis demonstrated a three-factor solution ('learning-teaching milieu', 'teaching skills', and 'learner-orientated'). A generalizability coefficient was 0.92. Mean time to complete the instrument was five minutes. Feedback indicated that it was an acceptable and useful method of assessment. This new instrument provides valid, reliable, feasible, and acceptable assessment of clinical teaching.

  3. Optimization of a pavement instrumentation plan for a full-scale test road : evaluation.

    Science.gov (United States)

    2014-04-01

    A 2.5-mile, concrete test road is planned for construction by the Florida Department of Transportation (FDOT) in : 2016. To support the goals of the test road, a comprehensive instrumentation system is required to provide : reliable data over a long ...

  4. The development and psychometric validation of the self-efficacy and performance in self-management support (SEPSS) Instrument.

    Science.gov (United States)

    Duprez, Veerle; Van Hooft, Susanne M; Dwarswaard, Jolanda; van Staa, AnneLoes; Van Hecke, Ann; Strating, Mathilde M H

    2016-06-01

    To develop and psychometrically test the self-efficacy and performance in self-management support (SEPSS) instrument. Facilitating persons with a chronic condition to take an active role in the management of their condition, implicates that nurses acquire new competencies. An instrument that can validly and reliably measure nurses' performance and their perceived capacity to perform self-management support is needed to evaluate current practice and training in self-management support. Instrument development and psychometric testing of the content and construct validity, factor structure and reliability. A literature review and expert consultation (N = 17) identified the content. The items were structured according to the Five-A's model and an overarching category of 'overall' competencies. The initial instrument was tested in a sample of 472 nurses and 51 nursing students from Belgium and the Netherlands, between June 2014-January 2015. Confirmatory factor analyses revealed satisfactory fit indices for the six-factor structure. Discriminating power was demonstrated for subgroups. The overall internal consistency (Cronbach's alpha) was high both for the self-efficacy and the performance items. The test-retest intra-class correlation coefficients were good. The SEPSS instrument is a 36-item, Likert-scaled self-reporting instrument with good content and construct validity, and good internal consistency reliability and good test-retest reliability. Therefore, it is a promising instrument to measure self-efficacy and performance with regard to self-management support. © 2016 John Wiley & Sons Ltd.

  5. Irradiation tests of materials using HANARO instrumented capsules in 2003

    International Nuclear Information System (INIS)

    Joo, K. M.; Joe, M. S.; Oh, J. M.; Shin, Y. T.; Kang, Y. H.; Lim, I. C.; Hwang, S. R.

    2003-01-01

    The HANARO irradiation capsule system has been actively utilized for the various irradiation tests requested by users of research institutes, universities, and industries. In 2003, two instrumented capsules were designed, fabricated, and successfully irradiated at HANARO and another is under fabrication. For the evaluation of the irradiation properties of the RPV(Reactor Pressure Vessel) materials and for the development of improved evaluation technology, 02M-02K instrumented capsule was designed, fabricated, and successfully irradiated at HANARO. 02M-05U instrumented capsule was designed, fabricated, and successfully irradiated as a part of 2002 project for active utilization of HANARO. Reactor core materials were also irradiated using 02M-05U capsule. Another instrumented capsule is under design and fabrication as a part of 2003 project for active utilization of HANARO and for the development of precise temperature controlling technology

  6. Project W-049H instrument and control Acceptance Test Procedure

    International Nuclear Information System (INIS)

    Carrigan, M.C.

    1994-01-01

    The purpose of this Acceptance Test Procedure (ATP) for the Project W-049H, Treated Effluent Disposal Facility, is to verify that the instrument and control systems have been installed in accordance with the design documents and function as required by the project criteria. The instrument and control system includes three operator control stations, modems, and general purpose LAN interface cabinets in the Effluent Treatment Facility control room; two pump stations; disposal station pumping building; and all local control units installed in the fold. Testing will be performed using actual signals when available and simulated signals when actual signals are unavailable

  7. AGARD Flight Test Instrumentation Series. Volume 15. Gyroscopic Instruments and Their Application to Flight Testing

    Science.gov (United States)

    1982-09-01

    and Instrumentation. tiol ister. W. N. NMIT Press, Camridge. Ness., (1969). Denhard, W. G. [3.2] Arnold , R. N. Gyrodynamics and its Engineering...held by Deutsche Gesell - schaft fur Ortung und Navigation a. V..* Stuttgart, Germany. September 28 and 29. 1977. [3.5] Drew, T. A. Advances in...Fried, 1. R. J. Wiley & Sons, New York (1969). (Editors) [5.6] Arnold , R. N. Gyrodynamics. Maunder, L. Academic Press, New York (1961). [5.7] Litton

  8. GMI Instrument Spin Balance Method, Optimization, Calibration, and Test

    Science.gov (United States)

    Ayari, Laoucet; Kubitschek, Michael; Ashton, Gunnar; Johnston, Steve; Debevec, Dave; Newell, David; Pellicciotti, Joseph

    2014-01-01

    The Global Microwave Imager (GMI) instrument must spin at a constant rate of 32 rpm continuously for the 3 year mission life. Therefore, GMI must be very precisely balanced about the spin axis and CG to maintain stable scan pointing and to minimize disturbances imparted to the spacecraft and attitude control on-orbit. The GMI instrument is part of the core Global Precipitation Measurement (GPM) spacecraft and is used to make calibrated radiometric measurements at multiple microwave frequencies and polarizations. The GPM mission is an international effort managed by the National Aeronautics and Space Administration (NASA) to improve climate, weather, and hydro-meteorological predictions through more accurate and frequent precipitation measurements. Ball Aerospace and Technologies Corporation (BATC) was selected by NASA Goddard Space Flight Center to design, build, and test the GMI instrument. The GMI design has to meet a challenging set of spin balance requirements and had to be brought into simultaneous static and dynamic spin balance after the entire instrument was already assembled and before environmental tests began. The focus of this contribution is on the analytical and test activities undertaken to meet the challenging spin balance requirements of the GMI instrument. The novel process of measuring the residual static and dynamic imbalances with a very high level of accuracy and precision is presented together with the prediction of the optimal balance masses and their locations.

  9. Tri-Service Thermal Radiation Test Facility Technical Support Plan (TSP) Instructions

    National Research Council Canada - National Science Library

    Olson, Nicholas

    1997-01-01

    ...) are described in this technical support document. Details of proposed testing including the anticipated number of tests, requested instrumentation, required thermal, aerodynamic, and mechanical load test loads, and potential hazards are addressed...

  10. Instrumentation Facility

    Data.gov (United States)

    Federal Laboratory Consortium — Provides instrumentation support for flight tests of prototype weapons systems using a vast array of airborne sensors, transducers, signal conditioning and encoding...

  11. Instrumentation and testing of a prestressed concrete containment vessel model

    International Nuclear Information System (INIS)

    Hessheimer, M.F.; Pace, D.W.; Klamerus, E.W.

    1997-01-01

    Static overpressurization tests of two scale models of nuclear containment structures - a steel containment vessel (SCV) representative of an improved, boiling water reactor (BWR) Mark II design and a prestressed concrete containment vessel (PCCV) for pressurized water reactors (PWR) - are being conducted by Sandia National Laboratories for the Nuclear Power Engineering Corporation of Japan and the U.S. Nuclear Regulatory Commission. This paper discusses plans for instrumentation and testing of the PCCV model. 6 refs., 2 figs., 2 tabs

  12. Disturbance induced by surface preparation on instrumented indentation test

    International Nuclear Information System (INIS)

    Li, Yugang; Kanouté, Pascale; François, Manuel

    2015-01-01

    Surface preparation, which may induce considerable sample disturbance, plays an important role in instrumented indentation test (IIT). In this study, the sample disturbance (mainly divided into residual stresses and plastic strain) induced by the surface preparation process of instrumented indentation test specimens were investigated with both experimental tests and numerical simulations. Grazing incidence X-ray diffractions (GIXRD) and uniaxial tensile tests were conducted for characterizing the residual stresses and high plastic strain in the top surface layers of a carefully mechanically polished indentation sample, which, in the present work, is made of commercially pure titanium. Instrumented indentation tests and the corresponding finite element simulations were performed as well. For comparison, a reference sample (carefully mechanically polished & electrolytically polished) which represents the raw material was prepared and tested. Results showed that a careful mechanical polishing procedure can effectively reduce the level of residual stresses induced by this process. However, the high plastic strain in the surface region imposed by the polishing process is significant. The induced plastic strain can affect a depth up to 5 µm, which is deeper than the maximum penetration depth h max (3 µm) used for the instrumented indentation tests. In the near surface layer (in the range of depth about 350 nm), the plastic strain levels are fairly high. In the very top layer, the plastic strain was even estimated to reach more than 60%. The simultaneous use of indentation tests and numerical simulations showed that the existence of high plastic strain in the surface region will make the load vs depth (P–h) curve shift upwards, the contact hardness (H) increase and the contact stiffness (S) decrease

  13. Testing for the Best Instrument to Generate Sustainable Food Consumption

    Directory of Open Access Journals (Sweden)

    Luca Panzone

    2011-12-01

    Full Text Available  The increase in the level of greenhouse gas (GHG emissions in the atmosphere in the last centuries, and the subsequent increase in temperature, has been a widely studied area in the last few decades. Climate change has become a key item on the political agenda due to concerns regarding the sustainability of current human consumption for future generations. Consumption of food and agricultural goods constitutes an important part of household based GHG emissions, and the relatively low costs associated with environmental improvements make it an interesting area of study to understand behavioural changes. Despite general agreement on the need to curb the amount of GHG emissions worldwide, little evidence exists regarding the best instruments policymakers can employ to stimulate changes toward more sustainable consumption. The present work explores which instruments are most effective in fostering change to more environmentally friendly food consumption. The instruments tested are CO2 labelling, GHG abatement subsidy and product-specific bans. We used a simulated online shopping trip in supermarkets in the Greater London area in the United Kingdom, where respondents shopped in four product categories: cola, milk, meat (chicken and beef, and butter/margarine. Consumer preferences reveal that, in the presence of these instruments, quantity instruments performed better than price incentives and labelling.

  14. Radiometric instrumentation and measurements guide for photovoltaic performance testing

    Energy Technology Data Exchange (ETDEWEB)

    Myers, D.

    1997-04-01

    The Photovoltaic Module and Systems Performance and Engineering Project at the National Renewable Energy Laboratory performs indoor and outdoor standardization, testing, and monitoring of the performance of a wide range of photovoltaic (PV) energy conversion devices and systems. The PV Radiometric Measurements and Evaluation Team (PVSRME) within that project is responsible for measurement and characterization of natural and artificial optical radiation which stimulates the PV effect. The PV manufacturing and research and development community often approaches project members for technical information and guidance. A great area of interest is radiometric instrumentation, measurement techniques, and data analysis applied to understanding and improving PV cell, module, and system performance. At the Photovoltaic Radiometric Measurements Workshop conducted by the PVSRME team in July 1995, the need to communicate knowledge of solar and optical radiometric measurements and instrumentation, gained as a result of NREL`s long-term experiences, was identified as an activity that would promote improved measurement processes and measurement quality in the PV research and manufacturing community. The purpose of this document is to address the practical and engineering need to understand optical and solar radiometric instrument performance, selection, calibration, installation, and maintenance applicable to indoor and outdoor radiometric measurements for PV calibration, performance, and testing applications. An introductory section addresses radiometric concepts and definitions. Next, concepts essential to spectral radiometric measurements are discussed. Broadband radiometric instrumentation and measurement concepts are then discussed. Each type of measurement serves as an important component of the PV cell, module, and system performance measurement and characterization process.

  15. Dynamic instrumentation for the K-1600 seismic test facility recommissioning

    International Nuclear Information System (INIS)

    VanHoy, B.W.

    1991-01-01

    Martin Marietta Energy Systems, Inc. is the site contractor to the Department of Energy (DOE) for three Oak Ridge, Tennessee sites, the site in Portsmouth, Ohio, and the site in Paducah, Kentucky. To provide a focus for all natural phenomena engineering related problems, Martin Marietta Energy Systems, Inc. established the Center for Natural Phenomena Engineering under the technical direction of Dr. James E. Beavers. One of the Center's mandates is the determination of seismic properties of building structures containing sensitive processes. This has led to the recommissioning of the K-1600 Seismic Test Facility. The biaxial shake table in this facility was constructed during the eighties for seismic qualification of equipment of the Gas Centrifuge Enrichment Plant. After construction of the plant was terminated the Seismic Test Facility was placed in standby where it was left for six years. The facility's original instrumentation was evaluated versus the required instrumentation to augment its new expanded mission parameters. Instrumentation selection involving technology changes, age and attrition, and the new mission goals are discussed in this paper along with the rationale and budget that were involved with each decision. The testing potential of this facility along with the instrumentation upgrades necessary to accomplish these new tasks for the Center for Natural Phenomena Engineering are considered. New uses such as seismic qualification of equipment utilized in DOE's missions at various sites and waste treatment are proposed. This instrumentation selection is discussed in detail to show the rationale and proposed used of the facility as well as the capabilities of this DOE resource

  16. Vehicle for transporting instruments for testing against a wall

    International Nuclear Information System (INIS)

    Hyde, E.A.; Goldsmith, H.A.; Proudlove, M.J.

    1981-01-01

    This invention relates to a non-destructive testing apparatus and, in particular, to a vehicle that can be moved at will, for transporting instruments for testing against a surface remote from the operator. Under this invention a vehicle is intended, for instance, for testing the vessel of an installation containing a liquid metal cooled nuclear reactor of the pond type. Such an installation includes a nuclear reactor comprising an assembly containing a nuclear fuel immersed in a pond of liquid metal coolant, located in a vessel which is itself placed in a concrete containment vessel [fr

  17. Simple Instrumental and Visual Tests for Nonlaboratory Environmental Control

    Directory of Open Access Journals (Sweden)

    L. P. Eksperiandova

    2016-01-01

    Full Text Available Proposed are simple and available techniques that can be used for rapid and reliable environmental control specifically of natural water by means of instrumental and visual tests in outdoor conditions. Developed are the chemical colorimetric modes for fast detection of socially dangerous trace impurities in water such as Co(II, Pd(II, and Rh(III as well as NO2--ions and Fe(III serving as model impurities. Application of portable digital devices and scanner allows estimating the color coordinates and increasing the accuracy and sensitivity of the tests. The combination of complex formation with preconcentration of colored complexes replaces the sensitive but time-consuming and capricious kinetic method that is usually used for this purpose at the more convenient and reliable colorimetric method. As the test tools, the following ones are worked out: polyurethane foam tablets with sorbed colored complexes, the two-layer paper sandwich packaged in slide adapter and saturated by reagents, and polyethylene terephthalate blister with dried reagents. Fast analysis of polyurethane foam tablets is realized using a pocket digital RGB-colorimeter or portable photometer. Express analysis of two-layer paper sandwich or polyethylene terephthalate blister is realized by visual and instrumental tests. The metrological characteristics of the developed visual and instrumental express analysis techniques are estimated.

  18. Instrumentation and control activities at the Electric Power Research Institute to support operator support systems

    International Nuclear Information System (INIS)

    Naser, J.

    1995-01-01

    Most nuclear power plants in the United States continue to operate with analog instrumentation and control (I and C) technology designed 20 to 40 years ago. This equipment is approaching or exceeding its life expectancy, resulting in increasing maintenance efforts to sustain system performance. Decreasing availability of replacement parts and the accelerating deterioration of the infrastructure of manufacturers that support analog technology exacerbate obsolescence problems and resultant operation and maintenance (O and M) cost increases. Modern digital technology holds a significant potential to improve the safety, cost-effectiveness, productivity, and, therefore, competitiveness of nuclear power plants. Operator support systems provide the tools to help achieve this potential. Reliable, integrated information is a critical element for protecting the utility's capital investment and increasing availability, reliability, and productivity. Integrated operator support systems with integrated information can perform more effectively to increase productivity, to enhance safety, and to reduce O and M costs. The plant communications and computing architecture is the infrastructure needed to allow the implementation of I and C systems and associated operator support systems in an integrated manner. Current technology for distributed digital systems, plant process computers, and plant communications and computing networks support the integration of systems and information. (author). 16 refs

  19. Mid Infrared Instrument cooler subsystem test facility overview

    Science.gov (United States)

    Moore, B.; Zan, J.; Hannah, B.; Chui, T.; Penanen, K.; Weilert, M.

    2017-12-01

    The Cryocooler for the Mid Infrared Instrument (MIRI) on the James Webb Space Telescope (JWST) provides cooling at 6.2K on the instrument interface. The cooler system design has been incrementally documented in previous publications [1][2][3][4][5]. It has components that traverse three primary thermal regions on JWST: Region 1, approximated by 40K; Region 2, approximated by 100K; and Region 3, which is at the allowable flight temperatures for the spacecraft bus. However, there are several sub-regions that exist in the transition between primary regions and at the heat reject interfaces of the Cooler Compressor Assembly (CCA) and Cooler Control Electronics Assembly (CCEA). The design and performance of the test facility to provide a flight representative thermal environment for acceptance testing and characterization of the complete MIRI cooler subsystem are presented.

  20. Workgroup for Hydraulic laboratory Testing and Verification of Hydroacoustic Instrumentation

    Science.gov (United States)

    Fulford, Janice M.; Armstrong, Brandy N.; Thibodeaux, Kirk G.

    2015-01-01

    An international workgroup was recently formed for hydraulic laboratory testing and verification of hydroacoustic instrumentation used for water velocity measurements. The activities of the workgroup have included one face to face meeting, conference calls and an inter-laboratory exchange of two acoustic meters among participating laboratories. Good agreement was found among four laboratories at higher tow speeds and poorer agreement at the lowest tow speed.

  1. MOEMS devices designed and tested for astronomical instrumentation in space

    Science.gov (United States)

    Zamkotsian, Frederic; Noell, Wilfried

    2012-03-01

    Next-generation astronomical instrumentation for ground-based and space telescopes could use MOEMS devices. Among them, Multi-Object Spectrographs (MOS) are the major instruments for studying primary galaxies and remote and faint objects. A promising solution for the object selection system is the use of MOEMS devices such as micromirror arrays (MMA) which allow the remote control of the multi-slit configuration in real time. We are engaged in a European development of MMA for generating reflective slit masks. Prototypes of MMA with 2048 individually addressable micromirrors made of single-crystal silicon were successfully designed, fabricated and tested. 100×200μm2 micromirrors can be tilted by electrostatic actuation yielding 24° mechanical tilt-angle. The micromirrors were successfully actuated before, during and after cryogenic cooling at 162K. Line-column addressing for individual mirrors has also been demonstrated. We were also engaged in a technical assessment of using a 2048 × 1080 DMD from Texas Instruments for space applications. For a MOS in space, the device should work in vacuum and at low temperature. Our tests reveal that the DMD remains fully operational at -40°C and in vacuum. A 1038 hours life test in space survey conditions, Total Ionizing Dose radiation, thermal cycling and vibrations/shocks have also been successfully completed. These results do not reveal any show-stopper concerning the ability of the DMD to meet environmental space requirements. These developments and tests demonstrate the full ability of this type of components for space instrumentation, especially in multi-object spectroscopy applications.

  2. Instrumentation and Controls Division, Technical Support Department Management Plan, FY 1993--FY 1996

    Energy Technology Data Exchange (ETDEWEB)

    Adkisson, B.P.; Kunselman, C.W.; Effler, R.P.; Miller, D.R.; Millet, A.J.; Stansberry, C.T.

    1993-08-01

    This report describes the organization, key functions, and major activities of the Technical Support Department The Department is the programmatic support element of the Instrumentation and Controls Division. The Department`s primary focus is the support of existing equipment and systems at Oak Ridge National Laboratory that are generally characterized as instrumentation and controls. The support takes the form of repair, calibration, fabrication, field engineering, preventive maintenance, software support, and record keeping.

  3. Instrumented impact testing machine with reduced specimen oscillation effects

    International Nuclear Information System (INIS)

    Rintamaa, R.; Rahka, K.; Wallin, K.

    1984-07-01

    Owing to small and inexpensive specimens the Charpy impact test is widely used in quality control and alloy development. Limitations in power reactor survellance capsules it is also widely used for safety analysis purposes. Instrumenting the tup and computerizing data acquisition, makes dynamic fracture mechanics data measurement possible and convenient. However, the dynamic effects (inertia forces, specimen oscillations) in the impact test cause inaccuracies in the recorded load-time diagram and hence diminish the reliability of the calculated dynamic fracture mechanics parameters. To decrease inaccuracies a new pendulum type of instrumented impact test apparatus has been developed and constructed in the Metals Laboratory of the Technical Research Centre of Finland. This tester is based on a new principle involving inverted test geometry. The purpose of the geometry inversion is to reduce inertia load and specimen oscillation effects. Further, the new impact tester has some other novel features: e.g. the available initia impact energy is about double compared to the conventional standard (300 J) impact tester allowing the use of larger (10 x 20 x 110 mm) bend specimens than normal Charpy specimens. Also, the rotation asix in the three point bending is nearly stationary making COD-measurements possible. An experimental test series is described in which the inertia effects and specimen oscillations are compared in the conventional and new impact tester utilizing Charpy V-notch specimens. Comparison of the two test geometries is also made with the aid of an analytical model using finite element method (FEM) analysis. (author)

  4. Instrumented Impact Testing: Influence of Machine Variables and Specimen Position

    Energy Technology Data Exchange (ETDEWEB)

    Lucon, E.; McCowan, C. N.; Santoyo, R. A.

    2008-09-15

    An investigation has been conducted on the influence of impact machine variables and specimen positioning on characteristic forces and absorbed energies from instrumented Charpy tests. Brittle and ductile fracture behavior has been investigated by testing NIST reference samples of low, high and super-high energy levels. Test machine variables included tightness of foundation, anvil and striker bolts, and the position of the center of percussion with respect to the center of strike. For specimen positioning, we tested samples which had been moved away or sideways with respect to the anvils. In order to assess the influence of the various factors, we compared mean values in the reference (unaltered) and altered conditions; for machine variables, t-test analyses were also performed in order to evaluate the statistical significance of the observed differences. Our results indicate that the only circumstance which resulted in variations larger than 5 percent for both brittle and ductile specimens is when the sample is not in contact with the anvils. These findings should be taken into account in future revisions of instrumented Charpy test standards.

  5. Test Report for Acceptance Test Procedure for Pumping Instrumentation and Control Skid L

    International Nuclear Information System (INIS)

    KOCH, M.R.

    1999-01-01

    This is a Test Report for Acceptance Test Procedure (ATP) RPP-5055. This test report provides the results of the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''L''. The ATP was successfully completed. A copy of the completed ATP is in the Appendix of this document

  6. Test Report for Acceptance Test Procedure for Pumping Instrumentation and Control Skid L

    Energy Technology Data Exchange (ETDEWEB)

    KOCH, M.R.

    1999-11-09

    This is a Test Report for Acceptance Test Procedure (ATP) RPP-5055. This test report provides the results of the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''L''. The ATP was successfully completed. A copy of the completed ATP is in the Appendix of this document.

  7. Test Report for Acceptance Test Procedure for Pumping and Instrumentation Control Skid ''K''

    CERN Document Server

    Johns, B R

    1999-01-01

    This is a Test Report for Acceptance Test Procedure (ATP) HNF-4276. This test report provides the results of the inspection and testing of the new Pumping and Instrumentation Control (PIC) skid designed as ''K''. The ATP was successfully completed. A copy of the completed ATP is in the Appendix of this document.

  8. Test Report for Acceptance Test Procedure for Pumping Instrumentation and Control Skid M

    International Nuclear Information System (INIS)

    KOCH, M.R.

    1999-01-01

    This is a Test Report for Acceptance Test Procedure (ATP) RPP-5073. This test report provides the results of the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''M''. The ATP was successfully completed. A copy of the completed ATP is in the Appendix of this document

  9. Instrumented impact testing machine with reduced specimen oscillation effects

    Science.gov (United States)

    Rintamaa, R.; Ranka, K.; Wallin, K.; Ikonen, K.; Talja, H.; Kotilainen, H.; Sirkkola, E.

    1984-07-01

    A pendulum-type instrumented Charpy test apparatus based on inverted test geometry was developed. Geometry inversion reduces inertia load and specimen oscillation effects. Initial impact energy is double that of standard (300 J) impact testers, allowing the use of larger (10 x 20 x 110 mm) bend specimens than normal Charpy specimens. The rotation axis in the three point bending is nearly stationary, making COD-measurements possible. Inertia effects and specimen oscillations are compared with the conventional tester, and using an analytical finite element model for Charpy V-notch specimens. Better performance for the inverted geometry is reported.

  10. A new device to test cutting efficiency of mechanical endodontic instruments.

    Science.gov (United States)

    Giansiracusa Rubini, Alessio; Plotino, Gianluca; Al-Sudani, Dina; Grande, Nicola M; Sonnino, Gianpaolo; Putorti, Ermanno; Cotti, Elisabetta; Testarelli, Luca; Gambarini, Gianluca

    2014-03-06

    The purpose of the present study was to introduce a new device specifically designed to evaluate the cutting efficiency of mechanically driven endodontic instruments. Twenty new Reciproc R25 (VDW, Munich, Germany) files were used to be investigated in the new device developed to test the cutting ability of endodontic instruments. The device consists of a main frame to which a mobile plastic support for the hand-piece is connected and a stainless-steel block containing a Plexiglas block against which the cutting efficiency of the instruments was tested. The length of the block cut in 1 minute was measured in a computerized program with a precision of 0.1mm. The instruments were activated by using a torque-controlled motor (Silver Reciproc; VDW, Munich, Germany) in a reciprocating movement by the "Reciproc ALL" program (Group 1) and in counter-clockwise rotation at 300 rpm (Group 2). Mean and standard deviations of each group were calculated and data were statistically analyzed with a one-way ANOVA test (P0.05). The cutting testing device evaluated in the present study was reliable and easy to use and may be effectively used to test cutting efficiency of both rotary and reciprocating mechanical endodontic instruments.

  11. Instrumentation with real-world considerations for integrated leakage testing

    International Nuclear Information System (INIS)

    Gibson, L.D.; Carp, J.

    1982-01-01

    In measuring leakage of containment structures, the precise determination of pressure, temperature, dewpoint and flow rate parameters is of critical importance. The change in these values over a specified test period provides the basis for computation of the leakage for a given pressurized volume. The performance of an Integrated Leak Rate Test (ILRT) on the containment is generally a critical path event that must be planned far in advance. The very nature of the test requires rapid, efficient acquisition and processing of data for determination, and sometimes correction, of leakages. Equipment selection is an important consideration which can directly affect the outcome of the test. The intent of this paper is to shed some light on the concerns of choosing an instrumentation package for the ILRT

  12. Lessons Learned During Instrument Testing for the Thermal Infrared Sensor (TIRS)

    Science.gov (United States)

    Peabody, Hume L.; Otero, Veronica; Neuberger, David

    2013-01-01

    The Themal InfraRed Sensor (TIRS) instrument, set to launch on the Landsat Data Continuity Mission in 2013, features a passively cooled telescope and IR detectors which are actively cooled by a two stage cryocooler. In order to proceed to the instrument level test campaign, at least one full functional test was required, necessitating a thermal vacuum test to sufficiently cool the detectors and demonstrate performance. This was fairly unique in that this test occurred before the Pre Environmental Review, but yielded significant knowledge gains before the planned instrument level test. During the pre-PER test, numerous discrepancies were found between the model and the actual hardware, which were revealed by poor correlation between model predictions and test data. With the inclusion of pseudo-balance points, the test also provided an opportunity to perform a pre-correlation to test data prior to the instrument level test campaign. Various lessons were learned during this test related to modeling and design of both the flight hardware and the Ground Support Equipment and test setup. The lessons learned in the pre-PER test resulted in a better test setup for the nstrument level test and the completion of the final instrument model correlation in a shorter period of time. Upon completion of the correlation, the flight predictions were generated including the full suite of off-nominal cases, including some new cases defined by the spacecraft. For some of these ·new cases, some components now revealed limit exceedances, in particular for a portion of the hardware that could not be tested due to its size and chamber limitations.. Further lessons were learned during the completion of flight predictions. With a correlated detalled instrument model, significant efforts were made to generate a reduced model suitable for observatory level analyses. This proved a major effort both to generate an appropriate network as well as to convert to the final model to the required

  13. Technical Support Section Instrument Support Program for nuclear and nonnuclear facilities with safety requirements

    International Nuclear Information System (INIS)

    Adkisson, B.P.; Allison, K.L.

    1995-01-01

    This document describes requirements, procedures, and supervisory responsibilities of the Oak Ridge National Laboratory (ORNL) Instrumentation and Controls (I ampersand C) Division's Technical Support Section (TSS) for instrument surveillance and maintenance in nonreactor nuclear facilities having identified Operational Safety Requirements (OSRs) or Limiting Conditions Document (LCDs). Implementation of requirements comply with the requirements of U.S. Department of Energy (DOE) Orders 5480.5, 5480.22, and 5481.1B; Martin Marietta Energy Systems, Inc. (Energy Systems), Policy Procedure ESS-FS-201; and ORNL SPP X-ESH-15. OSRs and LCDs constitute an agreement or contract between DOE and the facility operating management regarding the safe operation of the facility. One basic difference between OSRs and LCDs is that violation of an OSR is considered a Category II occurrence, whereas violation of an LCD requirement is considered a Category III occurrence (see Energy Systems Standard ESS-OP-301 and ORNL SPP X-GP-13). OSRs are required for high- and moderate-hazard nuclear facilities, whereas the less-rigorous LCDs are required for low-hazard nuclear facilities and selected open-quotes generally acceptedclose quotes operations. Hazard classifications are determined through a hazard screening process, which each division conducts for its facilities

  14. THE VIRTUAL INSTRUMENT: SUPPORT FOR GRID-ENABLED MCELL SIMULATIONS.

    Science.gov (United States)

    Casanova, Henri; Berman, Francine; Bartol, Thomas; Gokcay, Erhan; Sejnowski, Terry; Birnbaum, Adam; Dongarra, Jack; Miller, Michelle; Ellisman, Mark; Faerman, Marcio; Obertelli, Graziano; Wolski, Rich; Pomerantz, Stuart; Stiles, Joel

    2004-02-01

    Ensembles of widely distributed, heterogeneous resources, or Grids, have emerged as popular platforms for large-scale scientific applications. In this paper we present the Virtual Instrument project, which provides an integrated application execution environment that enables end-users to run and interact with running scientific simulations on Grids. This work is performed in the specific context of MCell, a computational biology application. While MCell provides the basis for running simulations, its capabilities are currently limited in terms of scale, ease-of-use, and interactivity. These limitations preclude usage scenarios that are critical for scientific advances. Our goal is to create a scientific "Virtual Instrument" from MCell by allowing its users to transparently access Grid resources while being able to steer running simulations. In this paper, we motivate the Virtual Instrument project and discuss a number of relevant issues and accomplishments in the area of Grid software development and application scheduling. We then describe our software design and report on the current implementation. We verify and evaluate our design via experiments with MCell on a real-world Grid testbed.

  15. WFIRST: Data/Instrument Simulation Support at IPAC

    Science.gov (United States)

    Laine, Seppo; Akeson, Rachel; Armus, Lee; Bennett, Lee; Colbert, James; Helou, George; Kirkpatrick, J. Davy; Meshkat, Tiffany; Paladini, Roberta; Ramirez, Solange; Wang, Yun; Xie, Joan; Yan, Lin

    2018-01-01

    As part of WFIRST Science Center preparations, the IPAC Science Operations Center (ISOC) maintains a repository of 1) WFIRST data and instrument simulations, 2) tools to facilitate scientific performance and feasibility studies using the WFIRST, and 3) parameters summarizing the current design and predicted performance of the WFIRST telescope and instruments. The simulation repository provides access for the science community to simulation code, tools, and resulting analyses. Examples of simulation code with ISOC-built web-based interfaces include EXOSIMS (for estimating exoplanet yields in CGI surveys) and the Galaxy Survey Exposure Time Calculator. In the future the repository will provide an interface for users to run custom simulations of a wide range of coronagraph instrument (CGI) observations and sophisticated tools for designing microlensing experiments. We encourage those who are generating simulations or writing tools for exoplanet observations with WFIRST to contact the ISOC team so we can work with you to bring these to the attention of the broader astronomical community as we prepare for the exciting science that will be enabled by WFIRST.

  16. Diagnostic development and support of MHD (magnetohydrodynamics) test facilities

    Energy Technology Data Exchange (ETDEWEB)

    1989-07-01

    Mississippi State University (MSU) is developing diagnostic instruments for Magnetohydrodynamics (MHD) power train data acquisition and for support of MHD component development test facilities. Microprocessor-controlled optical instruments, initially developed for HRSR support, are being refined, and new systems to measure temperatures and gas-seed-slag stream characteristics are being developed. To further data acquisition and analysis capabilities, the diagnostic systems are being interfaced with MHD Energy Center computers. Technical support for the diagnostic needs of the national MHD research effort is being provided. MSU personnel will also cooperate with government agencies and private industries to improve the transformation of research and development results into processes, products and services applicable to their needs.

  17. Advanced In-pile Instrumentation for Material and Test Reactors

    International Nuclear Information System (INIS)

    Rempe, J.L.; Knudson, D.L.; Daw, J.E.; Unruh, T.C.; Chase, B.M.; Davis, K.L.; Palmer, A.J.; Schley, R.S.

    2013-06-01

    The US Department of Energy sponsors the Advanced Test Reactor (ATR) National Scientific User Facility (NSUF) program to promote U.S. research in nuclear science and technology. By attracting new research users - universities, laboratories, and industry - the ATR NSUF facilitates basic and applied nuclear research and development, advancing U.S. energy security needs. A key component of the ATR NSUF effort is to design, develop, and deploy new in-pile instrumentation techniques that are capable of providing real-time measurements of key parameters during irradiation. This paper describes the strategy developed by the Idaho National Laboratory (INL) for identifying instrumentation needed for ATR irradiation tests and the program initiated to obtain these sensors. New sensors developed from this effort are identified; and the progress of other development efforts is summarized. As reported in this paper, INL staff is currently involved in several tasks to deploy real-time length and flux detection sensors, and efforts have been initiated to develop a crack growth test rig. Tasks evaluating 'advanced' technologies, such as fiber-optics based length detection and ultrasonic thermometers are also underway. In addition, specialized sensors for real-time detection of temperature and thermal conductivity are not only being provided to NSUF reactors, but are also being provided to several international test reactors. (authors)

  18. Instrumentation for accelerated life tests of concentrator solar cells.

    Science.gov (United States)

    Núñez, N; Vázquez, M; González, J R; Jiménez, F J; Bautista, J

    2011-02-01

    Concentrator photovoltaic is an emergent technology that may be a good economical and efficient alternative for the generation of electricity at a competitive cost. However, the reliability of these new solar cells and systems is still an open issue due to the high-irradiation level they are subjected to as well as the electrical and thermal stresses that they are expected to endure. To evaluate the reliability in a short period of time, accelerated aging tests are essential. Thermal aging tests for concentrator photovoltaic solar cells and systems under illumination are not available because no technical solution to the problem of reaching the working concentration inside a climatic chamber has been available. This work presents an automatic instrumentation system that overcomes the aforementioned limitation. Working conditions have been simulated by forward biasing the solar cells to the current they would handle at the working concentration (in this case, 700 and 1050 times the irradiance at one standard sun). The instrumentation system has been deployed for more than 10 000 h in a thermal aging test for III-V concentrator solar cells, in which the generated power evolution at different temperatures has been monitored. As a result of this test, the acceleration factor has been calculated, thus allowing for the degradation evolution at any temperature in addition to normal working conditions to be obtained.

  19. DAS: A Data Management System for Instrument Tests and Operations

    Science.gov (United States)

    Frailis, M.; Sartor, S.; Zacchei, A.; Lodi, M.; Cirami, R.; Pasian, F.; Trifoglio, M.; Bulgarelli, A.; Gianotti, F.; Franceschi, E.; Nicastro, L.; Conforti, V.; Zoli, A.; Smart, R.; Morbidelli, R.; Dadina, M.

    2014-05-01

    The Data Access System (DAS) is a and data management software system, providing a reusable solution for the storage of data acquired both from telescopes and auxiliary data sources during the instrument development phases and operations. It is part of the Customizable Instrument WorkStation system (CIWS-FW), a framework for the storage, processing and quick-look at the data acquired from scientific instruments. The DAS provides a data access layer mainly targeted to software applications: quick-look displays, pre-processing pipelines and scientific workflows. It is logically organized in three main components: an intuitive and compact Data Definition Language (DAS DDL) in XML format, aimed for user-defined data types; an Application Programming Interface (DAS API), automatically adding classes and methods supporting the DDL data types, and providing an object-oriented query language; a data management component, which maps the metadata of the DDL data types in a relational Data Base Management System (DBMS), and stores the data in a shared (network) file system. With the DAS DDL, developers define the data model for a particular project, specifying for each data type the metadata attributes, the data format and layout (if applicable), and named references to related or aggregated data types. Together with the DDL user-defined data types, the DAS API acts as the only interface to store, query and retrieve the metadata and data in the DAS system, providing both an abstract interface and a data model specific one in C, C++ and Python. The mapping of metadata in the back-end database is automatic and supports several relational DBMSs, including MySQL, Oracle and PostgreSQL.

  20. Learning a Musical Instrument: The Case for Parental Support

    Science.gov (United States)

    Creech, Andrea

    2010-01-01

    The aims of this research were to identify the ways in which parents may most constructively support their children's musical development, and to ascertain whether styles of parent-teacher and parent-pupil interaction would influence the extent to which parents engage in different types of supportive behaviours. A model of parent involvement as…

  1. Model-based testing of a vehicle instrument cluster for design validation using machine vision

    International Nuclear Information System (INIS)

    Huang, Yingping; McMurran, Ross; Dhadyalla, Gunwant; Jones, R Peter; Mouzakitis, Alexandros

    2009-01-01

    This paper presents an advanced testing system, combining model-based testing and machine vision technologies, for automated design validation of a vehicle instrument cluster. In the system, a hardware-in-the-loop (HIL) tester, supported by model-based approaches, simulates vehicle operations in real time and dynamically provides all essential signals to the instrument cluster under test. A machine vision system with advanced image processing algorithms is designed to inspect the visual displays. Experiments demonstrate that the system developed is accurate for measuring the pointer position, bar graph position, pointer angular velocity and indicator flash rate, and is highly robust for validating various functionalities including warning lights status, symbol and text displays. Moreover, the system developed greatly eases the task of tedious validation testing and makes onerous repeated tests possible

  2. Test Report for Acceptance Test Procedure for Pumping Instrumentation and Control Skid ''P''

    International Nuclear Information System (INIS)

    KOCH, M.R.

    2000-01-01

    This Acceptance Test Report (ATR) provides the test results for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''P''. The ATR summaries the results and provides a copy of the ATP and inspections in the Appendix

  3. Test Report for Acceptance Test Procedure for Pumping Instrumentation and Control Skid Q

    International Nuclear Information System (INIS)

    KOCH, M.R.

    2000-01-01

    This Acceptance Test Report (ATR) provides the test results for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''Q''. The ATR summaries the results and provides a copy of the ATP and inspections in the Appendix

  4. New In-pile Instrumentation to Support Fuel Cycle Research and Development

    Energy Technology Data Exchange (ETDEWEB)

    J. Rempe; H. MacLean; R. Schley; D. Hurley; J. Daw; S. Taylor; J. Smith; J. Svoboda; D. Kotter; D. Knudson; M. Guers; S. C. Wilkins

    2011-01-01

    New and enhanced nuclear fuels are a key enabler for new and improved reactor technologies. For example, the goals of the next generation nuclear plant (NGNP) will not be met without irradiations successfully demonstrating the safety and reliability of new fuels. Likewise, fuel reliability has become paramount in ensuring the competitiveness of nuclear power plants. Recently, the Office of Nuclear Energy in the Department of Energy (DOE-NE) launched a new direction in fuel research and development that emphasizes an approach relying on first principle models to develop optimized fuel designs that offer significant improvements over current fuels. To facilitate this approach, high fidelity, real-time, data are essential for characterizing the performance of new fuels during irradiation testing. A three-year strategic research program is proposed for developing the required test vehicles with sensors of unprecedented accuracy and resolution for obtaining the data needed to characterize three-dimensional changes in fuel microstructure during irradiation testing. When implemented, this strategy will yield test capsule designs that are instrumented with new sensor technologies for the Advanced Test Reactor (ATR) and other irradiation locations for the Fuel Cycle Research and Development (FC R&D) program. Prior laboratory testing, and as needed, irradiation testing, of these sensors will have been completed to give sufficient confidence that the irradiation tests will yield the required data. Obtaining these sensors must draw upon the expertise of a wide-range of organizations not currently supporting nuclear fuels research. This document defines this strategic program and provides the necessary background information related to fuel irradiation testing, desired parameters for detection, and an overview of currently available in-pile instrumentation. In addition, candidate sensor technologies are identified in this document, and a list of proposed criteria for ranking

  5. New In-pile Instrumentation to Support Fuel Cycle Research and Development

    International Nuclear Information System (INIS)

    Rempe, J.; MacLean, H.; Schley, R.; Hurley, D.; Daw, J.; Taylor, S.; Smith, J.; Svoboda, J.; Kotter, D.; Knudson, D.; Guers, M.; Wilkins, S.C.

    2011-01-01

    New and enhanced nuclear fuels are a key enabler for new and improved reactor technologies. For example, the goals of the next generation nuclear plant (NGNP) will not be met without irradiations successfully demonstrating the safety and reliability of new fuels. Likewise, fuel reliability has become paramount in ensuring the competitiveness of nuclear power plants. Recently, the Office of Nuclear Energy in the Department of Energy (DOE-NE) launched a new direction in fuel research and development that emphasizes an approach relying on first principle models to develop optimized fuel designs that offer significant improvements over current fuels. To facilitate this approach, high fidelity, real-time, data are essential for characterizing the performance of new fuels during irradiation testing. A three-year strategic research program is proposed for developing the required test vehicles with sensors of unprecedented accuracy and resolution for obtaining the data needed to characterize three-dimensional changes in fuel microstructure during irradiation testing. When implemented, this strategy will yield test capsule designs that are instrumented with new sensor technologies for the Advanced Test Reactor (ATR) and other irradiation locations for the Fuel Cycle Research and Development (FC R and D) program. Prior laboratory testing, and as needed, irradiation testing, of these sensors will have been completed to give sufficient confidence that the irradiation tests will yield the required data. Obtaining these sensors must draw upon the expertise of a wide-range of organizations not currently supporting nuclear fuels research. This document defines this strategic program and provides the necessary background information related to fuel irradiation testing, desired parameters for detection, and an overview of currently available in-pile instrumentation. In addition, candidate sensor technologies are identified in this document, and a list of proposed criteria for

  6. Irradiation Test of Dual Instrumented Fuel Rods by using an Instrumented Fuel Capsule(05F-01K) at HANARO

    International Nuclear Information System (INIS)

    Sohn, Jaemin; Park, Sungjae; Shin, Yoontaeg; Lee, Choongsung; Choo, Keenam; Cho, Mansoon; Oh, Jongmyung; Kim, Bonggoo; Kim, Harkrho

    2007-01-01

    The purpose of this paper is to verify the performance of dual instrumented fuel rods. The dual instrumented fuel rods, which allow for two characteristics to be measured simultaneously in one fuel rod, have been designed to enhance the efficiency of an irradiation test using an instrumented capsule for the nuclear fuel irradiation test(hereinafter referred to as 'instrumented fuel capsule') in HANARO(High-flux Advanced Neutron Application Reactor). Six types of dual instrumented fuel rods have been designed. The types of dual instrumented fuel rods are summarized as follows; 1) to measure the center temperature of the nuclear fuel and the internal pressure of the fuel rod, 2) to measure the center temperature of the nuclear fuel and the elongation of the fuel pellets, 3) to measure the surface temperature of the nuclear fuel and the internal pressure of the fuel rod, 4) to measure the surface temperature of the nuclear fuel and the elongation of the fuel pellets, 5) to measure the center and surface temperature of the nuclear fuel, and 6) to measure the center temperature of the nuclear fuel of the upper and lower part. And 05F-01K instrumented fuel capsule has been designed for an irradiation test of three dual instrumented fuel rods. This paper presents the manufacturing of the dual instrumented fuel rods and 05F-01K instrumented fuel capsule, and the results of the irradiation test

  7. Perceived overprotection, instrumental support and rehabilitation use in elders with vision loss: a longitudinal perspective.

    Science.gov (United States)

    Cimarolli, Verena R; Boerner, Kathrin; Reinhardt, Joann P; Horowitz, Amy

    2013-01-01

    This study's purpose was to investigate changes in perceived overprotection - a problematic aspect of close relationships - over time in relationship to instrumental support receipt and vision rehabilitation service use in a sample of older adults with vision impairment. Participants were 584 older adults with chronic vision impairment who were interviewed three times over a 12-month period. Longitudinal data were analysed using a latent growth curve methodology to examine change over time in perceived overprotection and instrumental support in relation to vision rehabilitation service use. Self-reported levels of overprotection and receipt of instrumental support. Results. Over time perceived overprotection increased but not instrumental support. While perceived overprotection was positively associated with instrumental support initially, over time this relationship did not emerge. Perceived overprotection and instrumental support functioned as predictors of vision rehabilitation hours. However, over time vision rehabilitation service use did not influence these social supports. Perceived overprotection increases over time, yet this change is unaffected by rehabilitation service use and instrumental support. Both family members and elders need to be involved in the vision rehabilitation process and educated about how some level of independence can be regained.

  8. The development and psychometric validation of the self-efficacy and performance in self-management support (SEPSS) Instrument

    NARCIS (Netherlands)

    V. Duprez (Veerle); S.M. van Hooft (Susanne); J. Dwarswaard (Jolanda); A.L. van Staa (AnneLoes); A. Van Hecke (Ann); M.M.H. Strating (Mathilde)

    2016-01-01

    markdownabstract__Aim:__ To develop and psychometrically test the self-efficacy and performance in self-management support (SEPSS) instrument. __Background:__ Facilitating persons with a chronic condition to take an active role in the management of their condition, implicates that nurses acquire

  9. Autonomy support in people with mild-to-borderline intellectual disability : Testing the Health Care Climate Questionnaire-Intellectual Disability

    NARCIS (Netherlands)

    Frielink, Noud; Schuengel, Carlo; Embregts, Petri J.C.M.

    2018-01-01

    Background: Autonomy support in people with intellectual disability (ID) is an important yet understudied topic. Psychometrically sound instruments are lacking. This study tested the factor structure and reliability of an instrument for assessing the extent people with intellectual disability

  10. Instrumental support in the physical activity community - premilinary results

    NARCIS (Netherlands)

    Elloumi, Lamia; Zhang, Qiwen; van Beijnum, Bernhard J.F.; Hermens, Hermanus J.

    Currently, we witness the growth of ICT-mediated solutions for chronic diseases management, especially to assist and support patients in lifestyle changes in order to improve their health condition. Being physically active is one the recommended lifestyle changes for patients with chronic diseases.

  11. Single specimen fracture toughness determination procedure using instrumented impact test

    International Nuclear Information System (INIS)

    Rintamaa, R.

    1993-04-01

    In the study a new single specimen test method and testing facility for evaluating dynamic fracture toughness has been developed. The method is based on the application of a new pendulum type instrumented impact tester equipped with and optical crack mouth opening displacement (COD) extensometer. The fracture toughness measurement technique uses the Double Displacement Ratio (DDR) method, which is based on the assumption that the specimen is deformed as two rigid arms that rotate around an apparent centre of rotation. This apparent moves as the crack grows, and the ratio of COD versus specimen displacement changes. As a consequence the onset ductile crack initiation can be detected on the load-displacement curve. Thus, an energy-based fracture toughness can be calculated. In addition the testing apparatus can use specimens with the Double ligament size as compared with the standard Charpy specimen which makes the impact testing more appropriate from the fracture mechanics point of view. The novel features of the testing facility and the feasibility of the new DDR method has been verified by performing an extensive experimental and analytical study. (99 refs., 91 figs., 27 tabs.)

  12. Instrumented Test of Sensory Integration for Balance: A Validation Study.

    Science.gov (United States)

    Freeman, Lynn; Gera, Geetanjali; Horak, Fay B; Blackinton, Mary T; Besch, Mark; King, Laurie

    Abnormal postural sway is associated with an increase in risk of falls but is difficult for clinicians to accurately quantify without access to laboratory equipment. Instrumenting clinical outcome measures using body-worn movement monitors is a low-cost alternative. This is the first study to compare the modified Clinical Test of Sensory Integration for Balance (i-mCTSIB) to the laboratory test of the Sensory Organization Test (SOT) with dynamic posturography in a group of participants with Parkinson's disease (PD) and subtle balance limitations. The purpose of this study was to (1) determine the concurrent validity of the i-mCTSIB with the SOT (6 and 4 conditions) and (2) compare the i-mCTSIB and the SOT to differentiate between individuals with and without recent falls within the previous 6 months. This cross-sectional study examined 26 participants with idiopathic PD who had a Motor Unified Parkinson's Disease Rating Scale score of 32.7 (13.5) out of 108. The composite and conditions 1 and 4 of the i-mCTSIB and SOT scores were significantly correlated: composite scores r = -0.64 (P ≤ .001), C1 r = -0.43 (P = .03), C3 r = -0.60 (P ≤ .01), and C4 r = -0.54 (P ≤ .001). A significant difference was observed in mean i-mCTSIB composite scores between fallers and nonfallers (P = .04). In contrast, the SOT composite was not significantly different between fallers and nonfallers (P = 0.31). The results suggest that the i-mCTSIB may be a valid and clinically meaningful measure of sensory organization in persons with PD, even those with mild postural instability as measured by the median Hoehn and Yahr score (2.0). Future research should evaluate predictive validity of the i-mCTSIB for prospective falls. The instrumented mCTSIB with portable, body-worn movement allows clinicians to quantify abnormal postural sway without the ceiling effects of clinical balance testing or the expense and importability of force plate technology in the SOT. Instrumenting mCTSIB may also

  13. Development of the Test Of Astronomy STandards (TOAST) Assessment Instrument

    Science.gov (United States)

    Slater, Timothy F.; Slater, S. J.

    2008-05-01

    Considerable effort in the astronomy education research (AER) community over the past several years has focused on developing assessment tools in the form of multiple-choice conceptual diagnostics and content knowledge surveys. This has been critically important in advancing the AER discipline so that researchers could establish the initial knowledge state of students as well as to attempt measure some of the impacts of innovative instructional interventions. Unfortunately, few of the existing instruments were constructed upon a solid list of clearly articulated and widely agreed upon learning objectives. This was not done in oversight, but rather as a result of the relative youth of AER as a discipline. Now that several important science education reform documents exist and are generally accepted by the AER community, we are in a position to develop, validate, and disseminate a new assessment instrument which is tightly aligned to the consensus learning goals stated by the American Astronomical Society - Chair's Conference on ASTRO 101, the American Association of the Advancement of Science's Project 2061 Benchmarks, and the National Research Council's National Science Education Standards. In response, researchers from the Cognition in Astronomy, Physics and Earth sciences Research (CAPER) Team at the University of Wyoming's Science & Math Teaching Center (UWYO SMTC) have designed a criterion-referenced assessment tool, called the Test Of Astronomy STandards (TOAST). Through iterative development, this instrument has a high degree of reliability and validity for instructors and researchers needing information on students’ initial knowledge state at the beginning of a course and can be used, in aggregate, to help measure the impact of course-length duration instructional strategies for courses with learning goals tightly aligned to the consensus goals of our community.

  14. Eddy current testing system for bottom mounted instrumentation welds

    International Nuclear Information System (INIS)

    Kobayashi, N.; Ueno, S.; Suganuma, N.; Oodake, T.; Maehara, T.; Kasuya, T.; Ichikawa, H.

    2015-01-01

    Eddy current testing (ECT) techniques are used to detect a defect, especially stress corrosion cracking. An ECT system and procedures have been developed for testing the bottom mounted instrumentation (BMI) weld area of the reactor vessel in a pressurized water reactor. It is difficult to position and move the probe on the BMI weld area because the area has complicated curved surfaces. The surface shape of weld area on the BMI mock-up was measured for generating the scanning trajectory of ECT probe. The space coordinates and the normal vectors at the scanning points as the scanning trajectory were calculated based on the measured results of weld surface shape. Each motion-axis position of the multi-axis robot corresponding to each scanning point was calculated by the inverse kinematic algorithm. The BMI mock-up test was performed using the developed ECT probe with the cross coil in the differential mode. The artificial SCC and EDM slits given on the build-up weld area were detected in the mock-up test. From the result of detecting defects, it is shown that this ECT system can detect a defect of approximately 2.3 mm in length, 0.5 mm in depth and 0.2 mm in width as the defect detection capability for the BMI welds. It was estimated that the average and the maximum probe tilt angles were 2.6 and 8.5 degrees, respectively

  15. Gamma thermometer longevity test: Laguna Verde 2 instruments recent performance

    Energy Technology Data Exchange (ETDEWEB)

    Cuevas V, G. [Global Nuclear Fuel, Americas, 3901 Castle Hayne Road, Wilmington, North Carolina (United States); Avila N, A.; Calleros M, G., E-mail: Gabriel.Cuevas-Vivas@gnf.com [Comision Federal de Electricidad, Central Nucleoelectrica Laguna Verda, Carretera Veracruz-Nautla Km 42.5, Alto Lucero, Veracruz (Mexico)

    2013-10-15

    This paper is informative of the General Electric Hitachi and Global Nuclear Fuel - Americas are collaboration with Comision Federal de Electricidad in a longevity test of thermocouples as power monitoring devices. The test conclusions will serve for final engineering design in detailing the Automated Fixed In-core Probes for calibration of the Local Power Range Monitors (LPRMs) of the Economic Simplified Boiling Water Reactor. This paper introduces the collaboration description and some recent performance evaluation of the thermocouples that are sensitive to gamma radiation and are known generically as Gamma Thermometers (G T). The G Ts in Laguna Verde 2 are radially located inside six instrumentation tubes in the core and consist of seven thermocouples, four are aligned with the LPRM heights and three are axially located between LPRM heights. The Laguna Verde 2 G T test has become the longest test of thermocouples as power monitoring devices in a BWR industry history and confirms their reliability in terms of time-dependent small noise under steady state reactor conditions and good agreement against Traversing In-core Probes power measurements. (Author)

  16. Gamma thermometer longevity test: Laguna Verde 2 instruments recent performance

    International Nuclear Information System (INIS)

    Cuevas V, G.; Avila N, A.; Calleros M, G.

    2013-10-01

    This paper is informative of the General Electric Hitachi and Global Nuclear Fuel - Americas are collaboration with Comision Federal de Electricidad in a longevity test of thermocouples as power monitoring devices. The test conclusions will serve for final engineering design in detailing the Automated Fixed In-core Probes for calibration of the Local Power Range Monitors (LPRMs) of the Economic Simplified Boiling Water Reactor. This paper introduces the collaboration description and some recent performance evaluation of the thermocouples that are sensitive to gamma radiation and are known generically as Gamma Thermometers (G T). The G Ts in Laguna Verde 2 are radially located inside six instrumentation tubes in the core and consist of seven thermocouples, four are aligned with the LPRM heights and three are axially located between LPRM heights. The Laguna Verde 2 G T test has become the longest test of thermocouples as power monitoring devices in a BWR industry history and confirms their reliability in terms of time-dependent small noise under steady state reactor conditions and good agreement against Traversing In-core Probes power measurements. (Author)

  17. Assessing the performance of renewable electricity support instruments

    International Nuclear Information System (INIS)

    Verbruggen, Aviel; Lauber, Volkmar

    2012-01-01

    The performance of feed-in tariffs and tradable certificates is assessed on criteria of efficacy, efficiency, equity and institutional feasibility. In the early stage of transition to an energy system based entirely on renewable energy supplies, renewable electricity can only thrive if support takes into account the specific technical, economic and political problems which result from embedding this electricity in conventional power systems whose technology, organizational structure, environmental responsibility and general mission differ profoundly from the emerging, renewable-based system. Support schemes need to capture the diversity of power supplies, the variable nature of some renewable supplies, and their different attributes for the purposes of public policy. They must take into account the variety of generators – including small, decentralized generation – emerging in a renewable-based system, and the new relationships between generators and customers. Renewable energy policies need a clear point of reference: because the incumbent power systems are not sustainable they must adapt to the requirements of the renewable ones, not the other way round. Incumbent systems carry the responsibility of paying the transition, something that corresponds best with the polluter pays principle. - Highlights: ► Present power systems must adapt to the requirements of growing renewable ones, not the opposite. ► Well performing support systems capture the diversity of renewable sources and technologies. ► Feed-in Tariffs are superior in addressing the renewables' diversity and in promoting innovation. ► Feed-in Tariffs put transition burdens on incumbents and stimulate independent producers.

  18. Measuring Test Case Similarity to Support Test Suite Understanding

    NARCIS (Netherlands)

    Greiler, M.S.; Van Deursen, A.; Zaidman, A.E.

    2012-01-01

    Preprint of paper published in: TOOLS 2012 - Proceedings of the 50th International Conference, Prague, Czech Republic, May 29-31, 2012; doi:10.1007/978-3-642-30561-0_8 In order to support test suite understanding, we investigate whether we can automatically derive relations between test cases. In

  19. Cognitive visualization as a support instrument by individual education

    Directory of Open Access Journals (Sweden)

    V. A. Uglev

    2014-01-01

    Full Text Available The process of individual education, as the most effective form of gaining domain knowledge can be intensified through the organizational methods (involving a tutor, hardware (using computing technology, and psychological techniques (in particular, applying a cognitive visual representation. Of particular interest is a combination of traditional and computer-aided tutor support for individualized learning approaches based on the specific means of mapping.A tutor is an intermediary between a student (pupil and a teacher or between a student and a knowledge source in case of self-learning to orient the educational process to the student's personal goals and implement the L. S. Vygotsky's mediation principle. Thus, the tutor faces a task to identify the personal learning goals, disclose the learning prospects and its supports, but the student plays a role of a decision-maker. One of the nuclear problems of tutorage is making an individual educational or didactic path, which expects making a kind of distinctive cognition route.An application of cognitive visualization as a tutor's tools, is aimed, primarily, at a comprehensive representation of subjective educational student's space. A student has to be oriented inside this space to reach the denoted goals. In this context it is possible to formulate the navigation problem, which may be solved it in the most rational way by educational space mapping and navigating in it at any moment of the educational process. All three basic qualities of maps (the presence of different spatial objects in the corresponding metric, vector and scale can be usefully applied to support an individualized learning process.The paper shows that personality-resource maps can be used for describing the learning situation and building an individual study program in graphical form when the specifics of direct individualized learning is taken into account. Performing both the implementation function and the signum one, a

  20. Creating Efficient Instrumentation Networks to Support Parametric Risk Transfer

    Science.gov (United States)

    Rockett, P.

    2009-04-01

    instrumentation. For example, even along the US coast, National Weather Service windspeed recorders are not designed to withstand the most intense hurricane winds, and with only 30 minutes of battery life, fail to record through major storms with their ubiquitous power outages. New, privately financed, windspeed recording networks are now being installed that are hurricane resistant and have long-life batteries to ensure that windspeeds will always be recorded and can then be employed in Cat bond triggers. For the developing world, the installation and maintenance of resilient recording networks can kick-start risk transfer mechanisms even in the absence of insurance.

  1. Assessing the quality of decision support technologies using the International Patient Decision Aid Standards instrument (IPDASi.

    Directory of Open Access Journals (Sweden)

    Glyn Elwyn

    Full Text Available To describe the development, validation and inter-rater reliability of an instrument to measure the quality of patient decision support technologies (decision aids.Scale development study, involving construct, item and scale development, validation and reliability testing.There has been increasing use of decision support technologies--adjuncts to the discussions clinicians have with patients about difficult decisions. A global interest in developing these interventions exists among both for-profit and not-for-profit organisations. It is therefore essential to have internationally accepted standards to assess the quality of their development, process, content, potential bias and method of field testing and evaluation.Scale development study, involving construct, item and scale development, validation and reliability testing.Twenty-five researcher-members of the International Patient Decision Aid Standards Collaboration worked together to develop the instrument (IPDASi. In the fourth Stage (reliability study, eight raters assessed thirty randomly selected decision support technologies.IPDASi measures quality in 10 dimensions, using 47 items, and provides an overall quality score (scaled from 0 to 100 for each intervention. Overall IPDASi scores ranged from 33 to 82 across the decision support technologies sampled (n = 30, enabling discrimination. The inter-rater intraclass correlation for the overall quality score was 0.80. Correlations of dimension scores with the overall score were all positive (0.31 to 0.68. Cronbach's alpha values for the 8 raters ranged from 0.72 to 0.93. Cronbach's alphas based on the dimension means ranged from 0.50 to 0.81, indicating that the dimensions, although well correlated, measure different aspects of decision support technology quality. A short version (19 items was also developed that had very similar mean scores to IPDASi and high correlation between short score and overall score 0.87 (CI 0.79 to 0.92.This work

  2. [Photoelectric parametric test system of LED based on virtual instrument].

    Science.gov (United States)

    Yang, Song-Tao; Wang, Jing; Wang, Li-Dong; Liang, Pei; Dong, Qian-Min

    2014-11-01

    The standardized measuring principle, requirements and implementations of the above parameters of LEDs were researched and analyzed in the present paper. Then a comprehensive test system involved with optics, machinery and computer was designed to accomplish data acquisition, algorithm design and interface design on virtual instrument using NI data acquisition card USB6210. And convincing results of LEDs' parameters, including peak wavelength, width of half-peak wavelength, centroid wavelength, chromaticity coordinates, purity, correlated color temperature and the forward voltage/current, were achieved with good consistency based on the measured spectrum. The system owns simple interface, reliable algorithms and stable results. Respective measurements on five kinds of color of LED result in an average error less than 3%, which show an ideal performance of the system.

  3. In situ radiological characterization to support a test excavation at a liquid waste disposal site

    International Nuclear Information System (INIS)

    Keele, B.D.; Bauer, R.G.; Blewett, G.R.; Troyer, G.L.

    1994-05-01

    An in situ radiological detection system was developed to support a small test excavation at a liquid waste disposal site at the Hanford Site in Richland, Washington. Instrumentation, calibration and comparisons to samples are discussed

  4. Instrumentation

    International Nuclear Information System (INIS)

    Prieur, G.; Nadi, M.; Hedjiedj, A.; Weber, S.

    1995-01-01

    This second chapter on instrumentation gives little general consideration on history and classification of instrumentation, and two specific states of the art. The first one concerns NMR (block diagram of instrumentation chain with details on the magnets, gradients, probes, reception unit). The first one concerns precision instrumentation (optical fiber gyro-meter and scanning electron microscope), and its data processing tools (programmability, VXI standard and its history). The chapter ends with future trends on smart sensors and Field Emission Displays. (D.L.). Refs., figs

  5. Superconductive material and magnetic field for damping and levitation support and damping of cryogenic instruments

    Science.gov (United States)

    Dolgin, Benjamin P. (Inventor)

    1994-01-01

    A superconductive load bearing support without a mechanical contact and vibration damping for cryogenic instruments in space is presented. The levitation support and vibration damping is accomplished by the use of superconducting magnets and the 'Meissner' effect. The assembly allows for transfer of vibration energy away from the cryogenic instrument which then can be damped by the use of either an electronic circuit or conventional vibration damping mean.

  6. 77 FR 15813 - Preoperational Testing of Instrument and Control Air Systems

    Science.gov (United States)

    2012-03-16

    ... COMMISSION Preoperational Testing of Instrument and Control Air Systems AGENCY: Nuclear Regulatory Commission..., ``Preoperational Testing of Instrument and Control Air Systems.'' This regulatory guide is being revised to address... instrument and control air systems (ICAS) to meet seismic requirement, ICAS air-dryer testing to meet dew...

  7. Eddy current testing system for bottom mounted instrumentation welds - 15206

    International Nuclear Information System (INIS)

    Kobayashi, N.; Ueno, S.; Suganuma, N.; Oodake, T.; Maehara, T.; Kasuya, T.; Ichikawa, H.

    2015-01-01

    We have demonstrated the scanning of eddy current testing (ECT) probe on the welds area including the nozzle, the J-welds and the buildup welds of the Bottom Mounted Instrumentation (BMI) mock-up using the developed ECT system and procedure. It is difficult to scan the probe on the BMI welds area because the area has a complex curved surface shape and narrow spaces. We made the space coordinates and the normal vectors on the scanning points as the scanning trajectory of probe on the welds area based on the measured results of welds surface shape on the mock-up. The multi-axis robot was used to scan the probe on the welds surface. Each motion axis position of the robot corresponding to each scanning point was calculated by the inverse kinematic algorithm. The BMI mock-up test was performed using the cross coil probe in the differential mode. The artificial stress corrosion cracking and the electrical discharge machining slits given on the mock-up surface were detected. The results show that the ECT can detect a defect of approximately 2.3 mm in length, 0.5 mm in depth and 0.2 mm in width for the BMI welds. From the output voltage of single coil, we estimated that the average and the maximum probe tilt angles on the mock-up surface under scanning were 2.6 degrees and 8.5 degrees, respectively

  8. Fabrication and Testing of Viscosity Measuring Instrument (Viscometer

    Directory of Open Access Journals (Sweden)

    A. B. HASSAN

    2006-01-01

    Full Text Available This paper presents the fabrication and testing of a simple and portable viscometer for the measurement of bulk viscosity of different Newtonian fluids. It is aimed at making available the instrument in local markets and consequently reducing or eliminating the prohibitive cost of importation. The method employed is the use of a D.C motor to rotate a disc having holes for infra-red light to pass through and fall on a photo-diode thus undergoing amplification and this signal being translated on a moving-coil meter as a deflection. The motor speed is kept constant but varies with changes in viscosity of the fluid during stirring, which alter signals being read on the meter. The faster is revolution per minute of the disc, the less the deflection on the meter and vise-versa. From the results of tests conducted on various sample fluids using data on standard Newtonian fluids as reliable guide the efficiency of the viscometer was 76.5%.

  9. Experimental Verification of an Instrument to Test Flooring Materials

    Science.gov (United States)

    Philip, Rony; Löfgren, Hans, Dr

    2018-02-01

    The focus of this work is to validate the fluid model with different flooring materials and the measurements of an instrument to test flooring materials and its force attenuating capabilities using mathematical models to describe the signature and coefficients of the floor. The main contribution of the present work focus on the development of a mathematical fluid model for floors. The aim of the thesis was to analyze, compare different floor materials and to study the linear dynamics of falling impacts on floors. The impact of the hammer during a fall is captured by an accelerometer and response is collected using a picoscope. The collected data was analyzed using matlab least square method which is coded as per the fluid model. The finding from this thesis showed that the fluid model works with more elastic model but it doesn’t work for rigid materials like wood. The importance of parameters like velocity, mass, energy loss and other coefficients of floor which influences the model during the impact of falling on floors were identified and a standardized testing method was set.

  10. Controlled Impact Demonstration instrumented test dummies installed in plane

    Science.gov (United States)

    1984-01-01

    In this photograph are seen some of dummies in the passenger cabin of the B-720 aircraft. NASA Langley Research Center instrumented a large portion of the aircraft and the dummies for loads in a crashworthiness research program. In 1984 NASA Dryden Flight Research Facility and the Federal Aviation Adimistration (FAA) teamed-up in a unique flight experiment called the Controlled Impact Demonstration (CID). The test involved crashing a Boeing 720 aircraft with four JT3C-7 engines burning a mixture of standard fuel with an additive called Anti-misting Kerosene (AMK) designed to supress fire. In a typical aircraft crash, fuel spilled from ruptured fuel tanks forms a fine mist that can be ignited by a number of sources at the crash site. In 1984 the NASA Dryden Flight Research Facility (after 1994 a full-fledged Center again) and the Federal Aviation Administration (FAA) teamed-up in a unique flight experiment called the Controlled Impact Demonstration (CID), to test crash a Boeing 720 aircraft using standard fuel with an additive designed to supress fire. The additive, FM-9, a high-molecular-weight long-chain polymer, when blended with Jet-A fuel had demonstrated the capability to inhibit ignition and flame propagation of the released fuel in simulated crash tests. This anti-misting kerosene (AMK) cannot be introduced directly into a gas turbine engine due to several possible problems such as clogging of filters. The AMK must be restored to almost Jet-A before being introduced into the engine for burning. This restoration is called 'degradation' and was accomplished on the B-720 using a device called a 'degrader.' Each of the four Pratt & Whitney JT3C-7 engines had a 'degrader' built and installed by General Electric (GE) to break down and return the AMK to near Jet-A quality. In addition to the AMK research the NASA Langley Research Center was involved in a structural loads measurement experiment, which included having instrumented dummies filling the seats in the

  11. A bootstrap test for instrument validity in heterogeneous treatment effect models

    OpenAIRE

    Kitagawa, Toru

    2013-01-01

    This paper develops a specification test for the instrument validity conditions in the heterogeneous treatment effect model with a binary treatment and a discrete instrument. A necessary testable implication for the joint restriction of instrument exogeneity and instrument monotonicity is given by nonnegativity of point-identifiable complier's outcome densities. Our specification test infers this testable implication using a Kolmogorov-Smirnov type test statistic. We provide a bootstrap algor...

  12. Factors influencing success in quality-improvement collaboratives: development and psychometric testing of an instrument

    Directory of Open Access Journals (Sweden)

    Grol Richard PTM

    2010-10-01

    Full Text Available Abstract Background To increase the effectiveness of quality-improvement collaboratives (QICs, it is important to explore factors that potentially influence their outcomes. For this purpose, we have developed and tested the psychometric properties of an instrument that aims to identify the features that may enhance the quality and impact of collaborative quality-improvement approaches. The instrument can be used as a measurement instrument to retrospectively collect information about perceived determinants of success. In addition, it can be prospectively applied as a checklist to guide initiators, facilitators, and participants of QICs, with information about how to perform or participate in a collaborative with theoretically optimal chances of success. Such information can be used to improve collaboratives. Methods We developed an instrument with content validity based on literature and the opinions of QIC experts. We collected data from 144 healthcare professionals in 44 multidisciplinary improvement teams participating in two QICs and used exploratory factor analysis to assess the construct validity. We used Cronbach's alpha to ascertain the internal consistency. Results The 50-item instrument we developed reflected expert-opinion-based determinants of success in a QIC. We deleted nine items after item reduction. On the basis of the factor analysis results, one item was dropped, which resulted in a 40-item questionnaire. Exploratory factor analysis showed that a three-factor model provided the best fit. The components were labeled 'sufficient expert team support', 'effective multidisciplinary teamwork', and 'helpful collaborative processes'. Internal consistency reliability was excellent (alphas between .85 and .89. Conclusions This newly developed instrument seems a promising tool for providing healthcare workers and policy makers with useful information about determinants of success in QICs. The psychometric properties of the instrument are

  13. Opinion poll tests support for democratic initiatives

    International Nuclear Information System (INIS)

    Burkhart, L.A.

    1993-01-01

    A national opinion poll designed to test public support for a position paper on energy policy for the Clinton Administration and the new Congress, was released February 9 at a Capitol Hill press conference sponsored by the Environmental and Energy Study Institute. The poll, conducted by the Democratic polling firm Greenberg/Lake and Republican pollster Lance Tarrance, found voters want energy efficiency, conservation, and renewable energy as top priorities for the nation's energy policy. It also found voters are willing to seek these policies with tough regulation, tax incentives, and their own behavior. Also, voters appear to support taxes on pollution and energy use, whether the income is used to decrease taxes on personal income, or to reduce the deficit. However, voters oppose gas taxes and are divided on taxes for fossil fuels. Support for energy taxes increases if revenues generated by them are dedicated to deficit reduction. The poll also revealed: the public's desire for less emphasis on polluting sources of energy such as oil and coal; low levels of support for nuclear power; support for government initiatives to increase the fuel efficiency of consumer goods such as appliances and automobiles; opposition to a substantial increase in the gasoline tax; and support for green taxes on polluting sources of energy use at the same time policy makers remove federal tax subsidies on fuels that pollute

  14. Instrumentation

    International Nuclear Information System (INIS)

    Decreton, M.

    2002-01-01

    SCK-CEN's R and D programme on instrumentation involves the development of advanced instrumentation systems for nuclear applications as well as the assessment of the performance of these instruments in a radiation environment. Particular emphasis is on the use of optical fibres as umbilincal links of a remote handling unit for use during maintanance of a fusion reacor, studies on the radiation hardening of plasma diagnostic systems; investigations on new instrumentation for the future MYRRHA accelerator driven system; space applications related to radiation-hardened lenses; the development of new approaches for dose, temperature and strain measurements; the assessment of radiation-hardened sensors and motors for remote handling tasks and studies of dose measurement systems including the use of optical fibres. Progress and achievements in these areas for 2001 are described

  15. Instrumentation

    Energy Technology Data Exchange (ETDEWEB)

    Decreton, M

    2002-04-01

    SCK-CEN's R and D programme on instrumentation involves the development of advanced instrumentation systems for nuclear applications as well as the assessment of the performance of these instruments in a radiation environment. Particular emphasis is on the use of optical fibres as umbilincal links of a remote handling unit for use during maintanance of a fusion reacor, studies on the radiation hardening of plasma diagnostic systems; investigations on new instrumentation for the future MYRRHA accelerator driven system; space applications related to radiation-hardened lenses; the development of new approaches for dose, temperature and strain measurements; the assessment of radiation-hardened sensors and motors for remote handling tasks and studies of dose measurement systems including the use of optical fibres. Progress and achievements in these areas for 2001 are described.

  16. Recent Developments in Balloon Support Instrumentation at TIFR Balloon Facility, Hyderabad.

    Science.gov (United States)

    Vasudevan, Rajagopalan

    2012-07-01

    The Balloon Facility of Tata Institute of Fundamental Research has been conducting stratospheric balloon flights regularly for various experiments in Space Astronomy and Atmospheric Sciences. A continuous improvement in Balloon flight Support instrumentation by the Control Instrumentation Group to keep in space with the growing complexities of the scientific payloads have contributed to the total success of balloon flights conducted recently. Recent improvements in display of Balloon position during balloon flight by showing on real time the balloon GPS position against Google TM maps is of immense help in selecting the right spot for payload landing and safe recovery . For further speeding up the payload recovery process, a new GPS-GSM payload system has been developed which gives SMS of the payload position information to the recovery team on their cell phones. On parallel footing, a new GPS- VHF system has been developed using GPS and Radio Modems for Balloon Tracking and also for obtaining the payload impact point. On the Telecommand side, a single board Telecommand/ Timer weighing less than 2 Kg has been specially developed for use in the mesosphere balloon test flight. The interference on the existing Short Range Telemetry System has been eliminated by introducing a Band Pass Filter and LNA in the Receiving system of the modules, thereby enhancing its reliability. In this paper , we present the details of the above mentioned developments.

  17. Hydrogen recombiner catalyst test supporting data

    Energy Technology Data Exchange (ETDEWEB)

    Britton, M.D.

    1995-01-19

    This is a data package supporting the Hydrogen Recombiner Catalyst Performance and Carbon Monoxide Sorption Capacity Test Report, WHC-SD-WM-TRP-211, Rev 0. This report contains 10 appendices which consist of the following: Mass spectrometer analysis reports: HRC samples 93-001 through 93-157; Gas spectrometry analysis reports: HRC samples 93-141 through 93-658; Mass spectrometer procedure PNL-MA-299 ALO-284; Alternate analytical method for ammonia and water vapor; Sample log sheets; Job Safety analysis; Certificate of mixture analysis for feed gases; Flow controller calibration check; Westinghouse Standards Laboratory report on Bois flow calibrator; and Sorption capacity test data, tables, and graphs.

  18. Femoral Test Bed for Impedance Controlled Surgical Instrumentation

    Directory of Open Access Journals (Sweden)

    Christian Brendle

    2012-01-01

    Full Text Available The risk for patients during the standard procedure of revision of cemented artificial hip joints is unsatisfactorily highdue to its high level of invasiveness and limited access to the operative field. To reduce this risk we are developing anImpedance Controlled Surgical Instrumentation (ICOS system, which aims to establish real-time control during a BoneCement (BC milling process. For this, the relationship between the thickness of the BC and its frequency-dependentelectrical impedance is used to estimate the residual BC thickness. The aim is to avoid unintended cutting of boneby detecting the passage of the BC/bone boundary layer by the milling head. In a second step, an estimation of theresidual BC thickness will be used to improve process control. As a first step towards demonstrating the feasibility ofour approach, presented here are experimental studies to characterize the BC permittivity and to describe the process indetail. The results show that the permittivity properties of BC are dominated by its polymethyl methacrylate (PMMAfraction. Thus, PMMA can be used as a substitute for future experiments. Furthermore, a Femoral Test Bed (FTB wasdesigned. Using this setup we show it is feasible to accurately distinguish between slightly different thicknesses of BC.

  19. Autonomy Support in People with Mild-to-Borderline Intellectual Disability: Testing the Health Care Climate Questionnaire-Intellectual Disability

    Science.gov (United States)

    Frielink, Noud; Schuengel, Carlo; Embregts, Petri J. C. M.

    2018-01-01

    Background: Autonomy support in people with intellectual disability (ID) is an important yet understudied topic. Psychometrically sound instruments are lacking. This study tested the factor structure and reliability of an instrument for assessing the extent people with intellectual disability perceive their support staff as autonomy supportive.…

  20. Instrumentation

    International Nuclear Information System (INIS)

    Umminger, K.

    2008-01-01

    A proper measurement of the relevant single and two-phase flow parameters is the basis for the understanding of many complex thermal-hydraulic processes. Reliable instrumentation is therefore necessary for the interaction between analysis and experiment especially in the field of nuclear safety research where postulated accident scenarios have to be simulated in experimental facilities and predicted by complex computer code systems. The so-called conventional instrumentation for the measurement of e. g. pressures, temperatures, pressure differences and single phase flow velocities is still a solid basis for the investigation and interpretation of many phenomena and especially for the understanding of the overall system behavior. Measurement data from such instrumentation still serves in many cases as a database for thermal-hydraulic system codes. However some special instrumentation such as online concentration measurement for boric acid in the water phase or for non-condensibles in steam atmosphere as well as flow visualization techniques were further developed and successfully applied during the recent years. Concerning the modeling needs for advanced thermal-hydraulic codes, significant advances have been accomplished in the last few years in the local instrumentation technology for two-phase flow by the application of new sensor techniques, optical or beam methods and electronic technology. This paper will give insight into the current state of instrumentation technology for safety-related thermohydraulic experiments. Advantages and limitations of some measurement processes and systems will be indicated as well as trends and possibilities for further development. Aspects of instrumentation in operating reactors will also be mentioned.

  1. Outcomes of moral case deliberation--the development of an evaluation instrument for clinical ethics support (the Euro-MCD).

    Science.gov (United States)

    Svantesson, Mia; Karlsson, Jan; Boitte, Pierre; Schildman, Jan; Dauwerse, Linda; Widdershoven, Guy; Pedersen, Reidar; Huisman, Martijn; Molewijk, Bert

    2014-04-08

    Clinical ethics support, in particular Moral Case Deliberation, aims to support health care providers to manage ethically difficult situations. However, there is a lack of evaluation instruments regarding outcomes of clinical ethics support in general and regarding Moral Case Deliberation (MCD) in particular. There also is a lack of clarity and consensuses regarding which MCD outcomes are beneficial. In addition, MCD outcomes might be context-sensitive. Against this background, there is a need for a standardised but flexible outcome evaluation instrument. The aim of this study was to develop a multi-contextual evaluation instrument measuring health care providers' experiences and perceived importance of outcomes of Moral Case Deliberation. A multi-item instrument for assessing outcomes of Moral Case Deliberation (MCD) was constructed through an iterative process, founded on a literature review and modified through a multistep review by ethicists and health care providers. The instrument measures perceived importance of outcomes before and after MCD, as well as experienced outcomes during MCD and in daily work. A purposeful sample of 86 European participants contributed to a Delphi panel and content validity testing. The Delphi panel (n = 13), consisting of ethicists and ethics researchers, participated in three Delphi-rounds. Health care providers (n = 73) participated in the content validity testing through 'think-aloud' interviews and a method using Content Validity Index. The development process resulted in the European Moral Case Deliberation Outcomes Instrument (Euro-MCD), which consists of two sections, one to be completed before a participant's first MCD and the other after completing multiple MCDs. The instrument contains a few open-ended questions and 26 specific items with a corresponding rating/response scale representing various MCD outcomes. The items were categorised into the following six domains: Enhanced emotional support, Enhanced

  2. Outcomes of Moral Case Deliberation - the development of an evaluation instrument for clinical ethics support (the Euro-MCD)

    Science.gov (United States)

    2014-01-01

    Background Clinical ethics support, in particular Moral Case Deliberation, aims to support health care providers to manage ethically difficult situations. However, there is a lack of evaluation instruments regarding outcomes of clinical ethics support in general and regarding Moral Case Deliberation (MCD) in particular. There also is a lack of clarity and consensuses regarding which MCD outcomes are beneficial. In addition, MCD outcomes might be context-sensitive. Against this background, there is a need for a standardised but flexible outcome evaluation instrument. The aim of this study was to develop a multi-contextual evaluation instrument measuring health care providers’ experiences and perceived importance of outcomes of Moral Case Deliberation. Methods A multi-item instrument for assessing outcomes of Moral Case Deliberation (MCD) was constructed through an iterative process, founded on a literature review and modified through a multistep review by ethicists and health care providers. The instrument measures perceived importance of outcomes before and after MCD, as well as experienced outcomes during MCD and in daily work. A purposeful sample of 86 European participants contributed to a Delphi panel and content validity testing. The Delphi panel (n = 13), consisting of ethicists and ethics researchers, participated in three Delphi-rounds. Health care providers (n = 73) participated in the content validity testing through ‘think-aloud’ interviews and a method using Content Validity Index. Results The development process resulted in the European Moral Case Deliberation Outcomes Instrument (Euro-MCD), which consists of two sections, one to be completed before a participant’s first MCD and the other after completing multiple MCDs. The instrument contains a few open-ended questions and 26 specific items with a corresponding rating/response scale representing various MCD outcomes. The items were categorised into the following six domains: Enhanced

  3. Organizational learning, pilot test of Likert-type instruments

    Directory of Open Access Journals (Sweden)

    Manuel Alfonso Garzón Castrillón

    2010-09-01

    Full Text Available This paper presents the results obtained in the pilot study of instruments created to comply the specific objective of designing and validating instruments to study the capacity of organizational learning. The Likert measurement scale was used because it allowed to establish the pertinence of the dimension as variable in the context of organizational learning. A One-way Analysis of Variance (ANOVA was used, with statistical package SPSS. Some 138 variables in 3 factors and 40 affirmations were simplified.

  4. Testing of tunnel support: dynamic load testing of rock support containment systems (eg wire mesh).

    CSIR Research Space (South Africa)

    Ortlepp, WD

    1997-07-01

    Full Text Available The objective of this project was to determine the performance characteristics of containment elements of tunnel support in common use in South African mines under dynamic loading. The magnitude of the energy levels in this testing had...

  5. Instruments

    Energy Technology Data Exchange (ETDEWEB)

    Buehrer, W. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1996-12-31

    The present paper mediates a basic knowledge of the most commonly used experimental techniques. We discuss the principles and concepts necessary to understand what one is doing if one performs an experiment on a certain instrument. (author) 29 figs., 1 tab., refs.

  6. Ares I Scale Model Acoustic Test Instrumentation for Acoustic and Pressure Measurements

    Science.gov (United States)

    Vargas, Magda B.; Counter, Douglas

    2011-01-01

    Ares I Scale Model Acoustic Test (ASMAT) is a 5% scale model test of the Ares I vehicle, launch pad and support structures conducted at MSFC to verify acoustic and ignition environments and evaluate water suppression systems Test design considerations 5% measurements must be scaled to full scale requiring high frequency measurements Users had different frequencies of interest Acoustics: 200 - 2,000 Hz full scale equals 4,000 - 40,000 Hz model scale Ignition Transient: 0 - 100 Hz full scale equals 0 - 2,000 Hz model scale Environment exposure Weather exposure: heat, humidity, thunderstorms, rain, cold and snow Test environments: Plume impingement heat and pressure, and water deluge impingement Several types of sensors were used to measure the environments Different instrument mounts were used according to the location and exposure to the environment This presentation addresses the observed effects of the selected sensors and mount design on the acoustic and pressure measurements

  7. James Webb Space Telescope (JWST) Integrated Science Instruments Module (ISIM) Cryo-Vacuum (CV) Test Campaign Summary

    Science.gov (United States)

    Yew, Calinda; Whitehouse, Paul; Lui, Yan; Banks, Kimberly

    2016-01-01

    JWST Integrated Science Instruments Module (ISIM) has completed its system-level testing program at the NASA Goddard Space Flight Center (GSFC). In March 2016, ISIM was successfully delivered for integration with the Optical Telescope Element (OTE) after the successful verification of the system through a series of three cryo-vacuum (CV) tests. The first test served as a risk reduction test; the second test provided the initial verification of the fully-integrated flight instruments; and the third test verified the system in its final flight configuration. The complexity of the mission has generated challenging requirements that demand highly reliable system performance and capabilities from the Space Environment Simulator (SES) vacuum chamber. As JWST progressed through its CV testing campaign, deficiencies in the test configuration and support equipment were uncovered from one test to the next. Subsequent upgrades and modifications were implemented to improve the facility support capabilities required to achieve test requirements. This paper: (1) provides an overview of the integrated mechanical and thermal facility systems required to achieve the objectives of JWST ISIM testing, (2) compares the overall facility performance and instrumentation results from the three ISIM CV tests, and (3) summarizes lessons learned from the ISIM testing campaign.

  8. Construction Of Critical Thinking Skills Test Instrument Related The Concept On Sound Wave

    Science.gov (United States)

    Mabruroh, F.; Suhandi, A.

    2017-02-01

    This study aimed to construct test instrument of critical thinking skills of high school students related the concept on sound wave. This research using a mixed methods with sequential exploratory design, consists of: 1) a preliminary study; 2) design and review of test instruments. The form of test instruments in essay questions, consist of 18 questions that was divided into 5 indicators and 8 sub-indicators of the critical thinking skills expressed by Ennis, with questions that are qualitative and contextual. Phases of preliminary study include: a) policy studies; b) survey to the school; c) and literature studies. Phases of the design and review of test instruments consist of two steps, namely a draft design of test instruments include: a) analysis of the depth of teaching materials; b) the selection of indicators and sub-indicators of critical thinking skills; c) analysis of indicators and sub-indicators of critical thinking skills; d) implementation of indicators and sub-indicators of critical thinking skills; and e) making the descriptions about the test instrument. In the next phase of the review test instruments, consist of: a) writing about the test instrument; b) validity test by experts; and c) revision of test instruments based on the validator.

  9. A report on the instrumented Charpy impact test for metallic materials

    International Nuclear Information System (INIS)

    Kozuka, Toshihiko; Yoshida, Hiroyuki.

    1988-12-01

    An instrumented testing method has been developed for Charpy impact test for steels, aluminum alloys and other materials. Using the instrumented Charpy testing machine developed, it is clearly estimated that the method is good enough to give us detailed information about the impact properties of these metallic materials. (author)

  10. 'Test Driving' a Financing Instrument for Climate Adaptation

    NARCIS (Netherlands)

    Root, Liz; Krabben, van der Erwin; Spit, Tejo

    2016-01-01

    Urban physical public infrastructure is a frontline defense mechanism to manage and mitigate climate-related impacts. Market instruments are often cited as possible means to spread risk and reduce financial burdens on the public sector. The authors argue that existing research tends to focus on the

  11. Instrumental intelligent test of food sensory quality as mimic of human panel test combining multiple cross-perception sensors and data fusion

    International Nuclear Information System (INIS)

    Ouyang, Qin; Zhao, Jiewen; Chen, Quansheng

    2014-01-01

    Highlights: • To develop a novel instrumental intelligent test methodology for food sensory analysis. • A novel data fusion was used in instrumental intelligent test methodology. • Linear and nonlinear tools were comparatively used for modeling. • The instrumental test methodology can be imitative of human test behavior. - Abstract: Instrumental test of food quality using perception sensors instead of human panel test is attracting massive attention recently. A novel cross-perception multi-sensors data fusion imitating multiple mammal perception was proposed for the instrumental test in this work. First, three mimic sensors of electronic eye, electronic nose and electronic tongue were used in sequence for data acquisition of rice wine samples. Then all data from the three different sensors were preprocessed and merged. Next, three cross-perception variables i.e., color, aroma and taste, were constructed using principal components analysis (PCA) and multiple linear regression (MLR) which were used as the input of models. MLR, back-propagation artificial neural network (BPANN) and support vector machine (SVM) were comparatively used for modeling, and the instrumental test was achieved for the comprehensive quality of samples. Results showed the proposed cross-perception multi-sensors data fusion presented obvious superiority to the traditional data fusion methodologies, also achieved a high correlation coefficient (>90%) with the human panel test results. This work demonstrated that the instrumental test based on the cross-perception multi-sensors data fusion can actually mimic the human test behavior, therefore is of great significance to ensure the quality of products and decrease the loss of the manufacturers

  12. How to select Instruments supporting R&D and Innovation by Industry

    NARCIS (Netherlands)

    M.J.L. de Heide (Marcel); A.V. Kothiyal (Amit)

    2011-01-01

    textabstractWe present a theoretical framework which allows for the comparison of the effectiveness of tax measures, loans and funding, in supporting industry-oriented research. We estimate for each of the instruments the exact contribution required by a firm to decide on investing in R&D, given the

  13. Outcomes of moral case deliberation - the development of an evaluation instrument for clinical ethics support (the Euro-MCD)

    NARCIS (Netherlands)

    Svantesson, M.; Karlsson, J.; Boitte, P.; Schildman, J.; Dauwerse, L.; Widdershoven, G.; Pedersen, R.; Huisman, M.; Molewijk, A.C.

    2014-01-01

    Background: Clinical ethics support, in particular Moral Case Deliberation, aims to support health care providers to manage ethically difficult situations. However, there is a lack of evaluation instruments regarding outcomes of clinical ethics support in general and regarding Moral Case

  14. Technological considerations in emergency instrumentation preparedness. Phase II-D. Evaluation testing and calibration methodology for emergency radiological instrumentation

    International Nuclear Information System (INIS)

    Bramson, P.E.; Andersen, B.V.; Fleming, D.M.; Kathren, R.L.; Mulhern, O.R.; Newton, C.E.; Oscarson, E.E.; Selby, J.M.

    1976-09-01

    In response to recommendations from the Advisory Committee on Reactor Safeguards, the Division of Operational Safety, U.S. ERDA has contracted with Battelle, Pacific Northwest Laboratories to survey the adequacy of existing instrumentation at nuclear fuel cycle facilities to meet emergency requirements and to develop technical criteria for instrumentation systems to be used in assessment of environmental conditions following plant emergencies. This report, the fifth in a series, provides: (1) calibration methods to assure the quality of radiological measurements and (2) testing procedures for determining whether an emergency radiological instrument meets the performance specifications. Three previous reports in this series identified the emergency instrumentation needs for power reactors, mixed oxide fuel plants, and fuel reprocessing facilities. Each of these three reports contains a Section VI, which sets forth applicable radiological instrument performance criteria and calibration requirements. Testing and calibration procedures in this report have been formatted in two parts: IV and V, each divided into three subsections: (1) Power Reactors, (2) Mixed Oxide Fuel Plants, and (3) Fuel Reprocessing Facilities. The three performance criteria subsections directly coincide with the performance criteria sections of the previous reports. These performance criteria sections have been reproduced in this report as Part III with references of ''required action'' added

  15. Technological considerations in emergency instrumentation preparedness. Phase II-D. Evaluation testing and calibration methodology for emergency radiological instrumentation

    Energy Technology Data Exchange (ETDEWEB)

    Bramson, P.E.; Andersen, B.V.; Fleming, D.M.; Kathren, R.L.; Mulhern, O.R.; Newton, C.E.; Oscarson, E.E.; Selby, J.M.

    1976-09-01

    In response to recommendations from the Advisory Committee on Reactor Safeguards, the Division of Operational Safety, U.S. ERDA has contracted with Battelle, Pacific Northwest Laboratories to survey the adequacy of existing instrumentation at nuclear fuel cycle facilities to meet emergency requirements and to develop technical criteria for instrumentation systems to be used in assessment of environmental conditions following plant emergencies. This report, the fifth in a series, provides: (1) calibration methods to assure the quality of radiological measurements and (2) testing procedures for determining whether an emergency radiological instrument meets the performance specifications. Three previous reports in this series identified the emergency instrumentation needs for power reactors, mixed oxide fuel plants, and fuel reprocessing facilities. Each of these three reports contains a Section VI, which sets forth applicable radiological instrument performance criteria and calibration requirements. Testing and calibration procedures in this report have been formatted in two parts: IV and V, each divided into three subsections: (1) Power Reactors, (2) Mixed Oxide Fuel Plants, and (3) Fuel Reprocessing Facilities. The three performance criteria subsections directly coincide with the performance criteria sections of the previous reports. These performance criteria sections have been reproduced in this report as Part III with references of ''required action'' added.

  16. Development of the instrumented capsule for nuclear fuel irradiation test at HANARO

    International Nuclear Information System (INIS)

    Sohn, Jae Min; Oh, Jong Myung; Park, Sung Jae; Shin, Yoon Taeg; Kim, Bong Goo; Kang, Young Hwan; Kim, Hark Rho; Kim, Young Jin

    2006-01-01

    The instrumented capsule for the nuclear fuel irradiation test (hereinafter referred to as 'instrumented fuel capsule'), which is crucial for the verification of a nuclear fuel performance and safety, has been developed at HANARO (High-flux Advanced Neutron Application Reactor). The irradiation test of the first instrumented fuel capsule was carried out in March 2003 and the irradiation test of the second instrumented fuel capsule was carried out in April 2004 at HANARO. Through the irradiation tests of the two capsules, the design specifications and safety of the instrumented fuel capsule were successfully verified. In the first instrumented fuel capsule, only the technologies for measuring the center temperature of the nuclear fuel and neutron flux were implemented. In the second instrumented fuel capsule, the technologies for measuring the center temperature of the nuclear fuel, the internal pressure of the fuel rod, the elongation of the nuclear fuel and the neutron flux were implemented. Currently the dual instrumented technologies that alloy for two characteristics to be measured simultaneously in one fuel rod, is being developed. The duel instrumented fuel rods have been successfully designed as a part of the technology enhancement program for the instrumented fuel capsule. The instrumented fuel capsule will be utilized for the development of nuclear fuel. The instrumentation technologies for measuring the nuclear fuel characteristics will be applied to the 3-pin FTL (Fuel Test Loop) facility which is currently being developed. And, the duel instrumented technologies will contribute to enhancing the efficiency of the irradiation test using an instrumented fuel capsule at HANARO. (author)

  17. Instrumentation and control activities at the electric power research institute to support computerized support systems

    International Nuclear Information System (INIS)

    Naser, J.

    1996-01-01

    Most nuclear power plants in the United States are operating with their original analog I and C equipment. This equipment requires increasing maintenance efforts to sustain systems performance. Decreasing availability of replacement parts and support organization for analog technology accentuate obsolescence problems and resultant O and M cost increases. Modern technology, especially digital systems, offers improved functionality, performance, and reliability; solutions to obsolescence of equipment; reduction in O and M costs; and the potential to enhance safety. Digital systems, including computerized support systems, with their inherent advantages will be implemented only if reliable and cost-effective implementation and licensing acceptance is achieved and if the upgraded systems supports reduced power production costs. EPRI and its member utilities are working together under the Integrated I and C Upgrade Initiative to address I and C issues. (author). 23 refs

  18. Offsite testing in support of the Salt Repository Project

    International Nuclear Information System (INIS)

    Kalia, H.N.

    1987-04-01

    This report presents a rationale and recommendation to perform an offsite testing program in support of the Salt Repository Project. The investigation to be performed primarily consists of qualifying test methods and procedures, qualifying personnel-training procedures, evaluating test instruments and selected equipment, and obtaining mining and production equipment performance-related information. The key objective of these activities is to develop capabilities to be used at the exploratory shaft facility (ESF). The ESF is to be excavated at the Deaf Smith County site to characterize the salt site for the construction of a repository used to isolate radioactive waste from the biosphere. The bulk of the offsite testing work will be performed at Avery Island Salt Mine at New Iberia, Lousiana. Additional knowledge will be obtained by exchanging technical information either as participants or as observers at the Waste Isolation Pilot Plant (WIPP) site and the Asse Mine in the Federal Republic of Germany (FRG). It is estimated that the offsite testing program will cost approximately $9.3 million over 4 fiscal years. 14 refs., 1 fig., 8 tabs

  19. Test instruments used by Journal of Music Therapy authors from 1984-1997.

    Science.gov (United States)

    Gregory, D

    2000-01-01

    Issues of the Journal of Music Therapy from 1984 to 1997 were selected to investigate the application of test instruments in music therapy research. All experimental and descriptive research articles were reviewed to determine if the methodology included test instruments. Other types of measurements-physiological measures, behavioral observations, computerized devices, and self-reports were excluded from the analysis. Test instruments were categorized as either published, unpublished, or researcher-constructed. A test instrument was "published" if, after a search in the "Test Review Locator" of the Buros Mental Measurements Web Site, a reference was found in one or more of the following publications-Mental Measurement Yearbooks, Tests in Print, or Test Critiques. A test was categorized as "unpublished" if the developer was cited in the JMT article but the test was not located in one or more of the above publications. All other test instruments were categorized as researcher-constructed tests designed for the specific study in the article. From 1984-1997, 220 articles were published in JMT. Approximately 83% (n = 183) of the total were experimental or descriptive research studies. Of the 183 articles research studies, 92 (50%) included a test instrument. Reviews of method sections of the 92 articles resulted in a listing of 115 different test instruments. Percentages of researcher-constructed tests, unpublished tests, and published tests were 25%, 35%, and 40% respectively. Lists of tests document the all-encompassing range of client populations and the broad view of human behavior included in the practice of music as therapy. The Journal of Music Therapy, in addition to providing the latest research findings regarding the effectiveness of music as a therapeutic medium, provides an excellent source for updating information about the availability and applicability of test instruments for music therapy clinical practice and training.

  20. Development of Temperature Control Solutions for Non-Instrumented Nucleic Acid Amplification Tests (NINAAT

    Directory of Open Access Journals (Sweden)

    Tamás Pardy

    2017-06-01

    Full Text Available Non-instrumented nucleic acid amplification tests (NINAAT are a novel paradigm in portable molecular diagnostics. They offer the high detection accuracy characteristic of nucleic acid amplification tests (NAAT in a self-contained device, without the need for any external instrumentation. These Point-of-Care tests typically employ a Lab-on-a-Chip for liquid handling functionality, and perform isothermal nucleic acid amplification protocols that require low power but high accuracy temperature control in a single well-defined temperature range. We propose temperature control solutions based on commercially available heating elements capable of meeting these challenges, as well as demonstrate the process by which such elements can be fitted to a NINAAT system. Self-regulated and thermostat-controlled resistive heating elements were evaluated through experimental characterization as well as thermal analysis using the finite element method (FEM. We demonstrate that the proposed solutions can support various NAAT protocols, as well as demonstrate an optimal solution for the loop-mediated isothermal amplification (LAMP protocol. Furthermore, we present an Arduino-compatible open-source thermostat developed for NINAAT applications.

  1. Development of an embedded instrumentation system architecture and its comparison to the test and training enabling architecture

    Science.gov (United States)

    Michel, Howard E.; Fortier, Paul J.

    2006-05-01

    This paper describes an information-centric embedded instrumentation systems architecture (EISA) and in particular its technical reference model (TRM) as they relate to the network-centric Test and Training Enabling Architecture (TENA). The embedded instrumentation systems architecture is meant to describe the operational, behavioral and informational requirements for a general "embedded instrumentation test and evaluation system" encased within an operational weapons system. The weapons system application could be in a weapon round, or in an entire large platform such as a warfare fighting unit, battle group or single war-craft such as a ship, plane or tank. TENA and the EISA models have much in common as will be described. The differences lie in the focus of each model's intended application domain. Both are part of the military support communities for aiding the military in training, testing, evaluating, verification or validation of weapons systems.

  2. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid ''V''

    International Nuclear Information System (INIS)

    KOCH, M.R.

    2000-01-01

    This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designated as ''V''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

  3. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid R

    International Nuclear Information System (INIS)

    KOCH, M.R.

    2000-01-01

    This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''R''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

  4. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid ''P''

    International Nuclear Information System (INIS)

    KOCH, M.R.

    2000-01-01

    This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''P''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

  5. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid ''U''

    International Nuclear Information System (INIS)

    KOCH, M.R.

    2000-01-01

    This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''U''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

  6. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid ''T''

    International Nuclear Information System (INIS)

    KOCH, M.R.

    2000-01-01

    This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designated as ''T''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

  7. Acceptance Test Procedure for New Pumping and Instrumentation Control Skid N

    International Nuclear Information System (INIS)

    KOCH, M.R.

    1999-01-01

    This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping and Instrumentation Control (PIC) skid designed as ''N''. The ATP will be performed after the construction of the PIC skid in the shop

  8. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid T

    International Nuclear Information System (INIS)

    KOCH, M.R.

    2000-01-01

    This Acceptance Test Procedure (ATP) provides for the inspection and testing Of the new Pumping Instrumentation and Control (PIC) skid designed as ''T''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

  9. Acceptance Test Procedure for New Pumping and Instrumentation Control Skid L

    International Nuclear Information System (INIS)

    KOCH, M.R.

    1999-01-01

    This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping and Instrumentation Control (PIC) skid designed as ''L''. The ATP will be performed after the construction of the PIC skid in the shop

  10. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid V

    International Nuclear Information System (INIS)

    KOCH, M.R.

    2000-01-01

    This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control. (PIC) skid designed as ''V''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

  11. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid W

    International Nuclear Information System (INIS)

    KOCH, M.R.

    2000-01-01

    This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''W''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

  12. Perception and production of English vowels by German learners: instrumental-phonetic support in language teaching.

    Science.gov (United States)

    Barry, W J

    1989-01-01

    Results are presented from two experiments which examine the application of instrumental phonetic methods to the needs of the teacher of a foreign language. First, the use of a traditional psychophonetic test procedure as a diagnostic tool is demonstrated. Second, the effect of reading, imitation, and prompted recall on production is examined, and the implications for teaching and pronunciation monitoring discussed.

  13. Autonomy support in people with mild to borderline intellectual disability : Testing the Health Care Climate Questionnaire-Intellectual Disability (HCCQ-ID)

    NARCIS (Netherlands)

    Frielink, N.; Schuengel, C.; Embregts, P.J.C.M.

    2017-01-01

    Background Autonomy support in people with intellectual disability (ID) is an important yet understudied topic. Psychometrically sound instruments are lacking. This study tested the factor structure and reliability of an instrument for assessing the extent people with intellectual disability

  14. Instrument performance in bone density testing at five Australian centres

    Energy Technology Data Exchange (ETDEWEB)

    Khan, K.M.; Saul, A.; Wark, J.D. [Royal Melbourne Hospital, Parkville, VIC (Australia). Department of Medicine; Henzell, S.L. [Charles Gairdner Hospital, Perth, WA (Australia). Department of Endocrinology and Diabetes; Broderick, C. [University of NSW, Sydney, NSW (Australia); Prince, R.L. [University of Western Australia, Perth, WA. (Australia). Department of Medicine; Lomman, J. [Bone Densitometry Technologist, Ashford, SA (Australia)

    1997-10-01

    Using a multicentre reliability study the accuracy and short- and long-term precision of dual-energy X-ray absorptiometry (DXA) in vitro was compared on five instruments. Measures were performed using pencil beam mode on four Hologic QDR- 2000 densitometers and one Hologic QDR-1000/W (Hologic Inc, Waltham, MA). Short-term precision of bone mineral density measurement was less than 0.5% for spine phantoms (n= 10 for each centre, mean intrasite coefficient of variation [CV] 0.39{+-}0.09% [SD]) and for hip phantoms (n=10 for each centre, mean intrasite coefficient of variation [CV] 0.34{+-}0.10% [SD]). Between-centre measurement (n=10 for each phantom) of a single spine phantom and a single hip phantom (specified mineral contents - 58.5 g and 38.6 g, respectively) revealed ranges of bone mineral content of 57.7-58.1 g (all-point CV=0.52%) and 37.1-37.8 g (all-point CV=0.70%), respectively. When results from pairs of machines were compared there were statistically different mean BMD results for the majority of the ten possible pairings for both spine and hip measurements. Each study centre measured in vitro stability of phantom BMD measurements over a one year period (n=45-283, median 157 for spine; and n=0-262, median 38, for hip); CVs ranged from 0.38 % to 0.53% for the spine measurements and from 0.38 % to 0.54% for the hip measurements. The mean all-point accuracy of the spine phantom measurements was 99.1% and the hip phantom measurements was 96.7%. It is concluded that across a number of instruments assessed in this study, DXA demonstrates in vitro all-point precision of 0.5% for the spine phantom and 0.7% for the hip phantom. The instrument demonstrates accuracy of greater than 99% at the spine and 96% at the hip (authors). 14 refs., 3 tabs., 4 figs.

  15. Ares I Scale Model Acoustic Tests Instrumentation for Acoustic and Pressure Measurements

    Science.gov (United States)

    Vargas, Magda B.; Counter, Douglas D.

    2011-01-01

    The Ares I Scale Model Acoustic Test (ASMAT) was a development test performed at the Marshall Space Flight Center (MSFC) East Test Area (ETA) Test Stand 116. The test article included a 5% scale Ares I vehicle model and tower mounted on the Mobile Launcher. Acoustic and pressure data were measured by approximately 200 instruments located throughout the test article. There were four primary ASMAT instrument suites: ignition overpressure (IOP), lift-off acoustics (LOA), ground acoustics (GA), and spatial correlation (SC). Each instrumentation suite incorporated different sensor models which were selected based upon measurement requirements. These requirements included the type of measurement, exposure to the environment, instrumentation check-outs and data acquisition. The sensors were attached to the test article using different mounts and brackets dependent upon the location of the sensor. This presentation addresses the observed effect of the sensors and mounts on the acoustic and pressure measurements.

  16. Laboratory Support Services for Environmental Testing

    National Research Council Canada - National Science Library

    1997-01-01

    ...) were effectively managing their contracts for environmental test services and whether DoD organizations were effectively performing quality assurance procedures on environmental test results received...

  17. Testing as an inevitable instrument in today's language learning ...

    African Journals Online (AJOL)

    In teaching any aspect of language, learner must be tested to determine the progress made so far as well as data for other uses by the stakeholders in the education industry. This paper commenced by closely examining the issues of testing/assessment and affirms that reliability and validity are the hallmark of good ...

  18. Project Management as an instrument to support innovation for country development – Macedonia case study

    OpenAIRE

    Dzidrov, Misko

    2017-01-01

    East European countries are all in the group of modest innovators by the Global Entrepreneurship Monitor and they all have slight improvements in the recent years. They all have some government programmes to support innovation and entrepreneurship. Project management was used as an instrument with some features that can help bust new innovation product development and with that to help the economies to become Innovation-driven Economies. Project management with some features helps the innovat...

  19. Testing electrical insulation of LCT coils and instrumentation

    International Nuclear Information System (INIS)

    Luton, J.N.; Ulbricht, A.R.; Ellis, J.F.; Shen, S.S.; Wilson, C.T.; Okuno, K.; Siewerdt, L.O.; Zahn, G.R.; Zichy, J.A.

    1986-09-01

    Three of the superconducting test coils in the Large Coil Task (LCT) use conductors cooled internally by forced flow of helium. In the other three coils, the conductors are cooled externally by a bath of helium. The coils and facility are designed for rapid discharges (dumps) at voltages up to 2.5 kV, depending on coil design. Many coil sensors are connected electrically to the conductors. These sensor leads and signal conditioning equipment also experience high voltage. High-potential tests of ground insulation were performed on all components of the International Fusion Superconducting Magnet Test Facility (IFSMTF). Coil insulation was also tested by ring-down tests that produced voltage distributions within the coils like those occurring during rapid discharge. Methods were developed to localize problem areas and to eliminate them. The effect on breakdown voltage near the Paschen minimum of magnetic fields up to 2 T was investigated

  20. Initial testing of an instrument to measure teacher identity in physicians.

    Science.gov (United States)

    Starr, Susan; Haley, Heather-Lyn; Mazor, Kathleen M; Ferguson, Warren; Philbin, Mary; Quirk, Mark

    2006-01-01

    A previous study described 7 elements of teacher identity: intrinsic satisfaction from teaching, knowledge and skill about teaching, belonging to a community of teachers, receiving rewards for teaching, believing that being a doctor means being a teacher, feeling a responsibility to teach, and sharing clinical expertise. To conduct the initial testing of an instrument to measure the 7 elements of teacher identity in clinical educators and to consider the potential applications of such an instrument. A 37-item questionnaire was mailed to 153 preceptors of preclinical students. Categories reflected the elements of teacher identity listed here. Demographic data were collected. Means, alphas, ANOVAs, and paired t tests were calculated. Of 153 preceptors, 127 (83%) completed the questionnaire. Cronbach's alpha for the overall scale and several subscales were high. Salaried physicians and those who had completed a faculty development program scored significantly higher on several subscales than physicians who volunteered to teach or who did not have faculty development. This study provides preliminary evidence that teacher identity can be measured and that preceptors do not respond as a homogeneous group. Assessing teacher identity may be helpful to medical schools looking to identify and support physicians who teach.

  1. Cryogenic test facility instrumentation with fiber optic and fiber optic sensors for testing superconducting accelerator magnets

    Science.gov (United States)

    Chiuchiolo, A.; Bajas, H.; Bajko, M.; Castaldo, B.; Consales, M.; Cusano, A.; Giordano, M.; Giloux, C.; Perez, J. C.; Sansone, L.; Viret, P.

    2017-12-01

    The magnets for the next steps in accelerator physics, such as the High Luminosity upgrade of the LHC (HL- LHC) and the Future Circular Collider (FCC), require the development of new technologies for manufacturing and monitoring. To meet the HL-LHC new requirements, a large upgrade of the CERN SM18 cryogenic test facilities is ongoing with the implementation of new cryostats and cryogenic instrumentation. The paper deals with the advances in the development and the calibration of fiber optic sensors in the range 300 - 4 K using a dedicated closed-cycle refrigerator system composed of a pulse tube and a cryogen-free cryostat. The calibrated fiber optic sensors (FOS) have been installed in three vertical cryostats used for testing superconducting magnets down to 1.9 K or 4.2 K and in the variable temperature test bench (100 - 4.2 K). Some examples of FOS measurements of cryostat temperature evolution are presented as well as measurements of strain performed on a subscale of High Temperature Superconducting magnet during its powering tests.

  2. Analysis of Competitiveness and Support Instruments for Heat and Electricity Production from Wood Biomass in Latvia

    Science.gov (United States)

    Klavs, G.; Kudrenickis, I.; Kundzina, A.

    2012-01-01

    Utilisation of renewable energy sources is one of the key factors in a search for efficient ways of reducing the emissions of greenhouse gases and improving the energy supply security. So far, the district heating supply in Latvia has been based on natural gas, with the wood fuel playing a minor role; the same is true for decentralised combined heat-power (CHP) production. The paper describes a method for evaluation of the economic feasibility of heat and electricity production from wood biomass under the competition between different fuel types and taking into account the electricity market. For the simulation, a cost estimation model is applied. The results demonstrate that wood biomass can successfully be utilised for competitive heat production by boiler houses, while for electricity production by CHP utilities it cannot compete on the market (even despite the low prices on wood biomass fuel) unless particular financial support instruments are applied. The authors evaluate the necessary support level and the impact of two main support instruments - the investment subsidies and the feed-in tariff - on the economic viability of wood-fuelled CHP plants, and show that the feed-in tariff could be considered as an instrument strongly affecting the competitiveness of such type CHP. Regarding the feed-in tariff determination, a compromise should be found between the economy-dictated requirement to develop CHP projects concerning capacities above 5 MWel - on the one hand, and the relatively small heat loads in many Latvian towns - on the other.

  3. Instrumentation

    International Nuclear Information System (INIS)

    Didierjean, B.; Jobez, J-P.; Seguinot, J.; Ypsilantis, T.

    1997-01-01

    A Hybrid Photon Detector (HPD) is currently manufactured in the framework of the tests of LHC-B collaboration. These extremely fast and sensible detectors (95% efficiency and 1 ns time accuracy for a single electron) could be utilized in many other applications: long base neutrino oscillations and possibly, HELLAZ. The model consists of an array of 2,048 1 x 1 mm 2 on Si strips of 50 mm thickness placed in glass cylinders of 127 mm diameter provided with Si windows and containing focalization electrodes. The electron circuits on 16 VA3 readout ceramic chips where designed, realized and tested. The stainless steel base card provided with 40 vacuum holes was already realised. The first production tests of visible light bi-alkali photocathodes operating in high vacuum will be performed soon. The design of the RICH2 counter (covering polar angles from 12 to 120 mrad) has been modified by turning the 120 mrad mirror to increase the spectrometer luminosity, i.e. to increase the length of the radiation path in gas by a factor of two. A second mirror sends the image in a region behind the magnetic field return, a region well-shielded from the LHC interaction zone. This design will provided 28 points for a β = 1 tracks and an angular uncertainty of 0.34 mrad per point. To cover the entire image 115 HPD will be necessary. The reconstruction of the complex systems of rings has been recently accomplished for events typical for RICH2, downstream, to discriminate between pions and kaons between 16 and 180 GeV/c. A simulation of 3,068 tracks has produced only 19 erroneous identifications, i.e. 0.6%. Another, simulation of 1,989 tracks with the RICH upstream resulted in 39 erroneous π/K identification, i.e. 2%. The report presents also the long base RICH experiment for detecting neutrino oscillations. A new version of 100 m length and 18.6 m diameter (27 kt of water) provided with HPDs of 250 mm diameter with 85 6 x 6 mm 2 arrays has been designed. Fifty such detectors will be

  4. Modern instrumentation for radiation introscopic testing of welding quality

    International Nuclear Information System (INIS)

    Sosnin, F.R.

    1985-01-01

    Modern instrumenlation used for radiation introscopy of welded joints is discussed. the absolute (relative) sensitivity of radiation testing, resolution range, efficiency are considered as basic parameters of introscopes. The characteristics of fluoroscopes, radiation-television installations with the external scintillator and radiative image converter as well as with X-ray vidicons are given. The characterisitcs of radiation introscopes with manipulators to move objects being tested are analysed as well as digitized radiation introscopes

  5. Non-destructive natural frequency tests of cyclic fatigue-loaded nickel-titanium rotary instruments.

    Science.gov (United States)

    Hsieh, Sung-Chih; Lee, Sheng-Yang; Ciou, Chun-Yu; Huang, Haw-Ming

    2010-06-01

    Nickel-titanium (NiTi) instruments are extensively used in endodontic treatment because of their outstanding mechanical properties. However, unexpected fracture of NiTi rotary instruments occurs during endodontic procedures. Therefore, a reliable method to detect the structural status of a used NiTi instrument is needed. The aim of this study is to use natural frequency for monitoring structural changes of a NiTi instrument during and after the instrumentation process. In this study, laboratory modal testing experiments were performed on cyclic fatigue-loaded NiTi rotary instruments with a natural frequency detecting device. In addition, three-dimensional finite element (FE) models were established for assessing the structural changes that take place in repeatedly loaded NiTi instruments. Repeated rotational loading resulted in a significant decrease (p tested instruments reached 77-85% of their total life limit. In FE analysis, a strong correlation between natural frequency and change in elastic modulus of the NiTi instrument was found. These findings indicated that natural frequency may represent an effective parameter for evaluating the micro-structural status of NiTi rotary instruments subjected to fatigue loadings.

  6. Generation of Long-time Complex Signals for Testing the Instruments for Detection of Voltage Quality Disturbances

    Science.gov (United States)

    Živanović, Dragan; Simić, Milan; Kokolanski, Zivko; Denić, Dragan; Dimcev, Vladimir

    2018-04-01

    Software supported procedure for generation of long-time complex test sentences, suitable for testing the instruments for detection of standard voltage quality (VQ) disturbances is presented in this paper. This solution for test signal generation includes significant improvements of computer-based signal generator presented and described in the previously published paper [1]. The generator is based on virtual instrumentation software for defining the basic signal parameters, data acquisition card NI 6343, and power amplifier for amplification of output voltage level to the nominal RMS voltage value of 230 V. Definition of basic signal parameters in LabVIEW application software is supported using Script files, which allows simple repetition of specific test signals and combination of more different test sequences in the complex composite test waveform. The basic advantage of this generator compared to the similar solutions for signal generation is the possibility for long-time test sequence generation according to predefined complex test scenarios, including various combinations of VQ disturbances defined in accordance with the European standard EN50160. Experimental verification of the presented signal generator capability is performed by testing the commercial power quality analyzer Fluke 435 Series II. In this paper are shown some characteristic complex test signals with various disturbances and logged data obtained from the tested power quality analyzer.

  7. INSTRUMENTS OF SUPPORT FOR RESEARCH AND DEVELOPMENT FUNDED BY LEADING DOMESTIC AND INTERNATIONAL SCIENCE FOUNDATIONS

    Directory of Open Access Journals (Sweden)

    Irina E. Ilina

    2017-06-01

    Full Text Available Introduction: one of the key aspects of the knowledge economy development is the growing significance of the results of research and development. The education and basic research play a key role in this process. Funding for education and fundamental science is carried out mainly at the expense of the state resources, including a system of foundations for scientific, engineering and innovation activities in Russia. The purpose of this article is to present recommendations for improving the tools of domestic foundations in funding fundamental research and development, including education and training. The propositions are made with a comparative analysis of the domestic and foreign science foun dations’ activities. Materials and Methods: the authors used analysis, comparison, induction, deduction, graphical analysis, generalisation and other scientific methods during the study. Results: the lack of comparability between domestic and foreign scientific funds in the volume of funding allocated for basic research and development is revealed. This situation affects the scientific research. The foreign foundations have a wide range of instruments to support research projects at all stages of the life cycle of grants for education and training prior to release of an innovative product to market (the use of “innovation elevator” system. The Russian national scientific foundations have no such possibilities. The authors guess that the Russian organisations ignore some of the instruments for supporting research and development. Use of these tools could enhance the effectiveness of research projects. According to the study of domestic and foreign experience in supporting research and development, the authors proposed a matrix composed of instruments for support in the fields of basic scientific researches and education with such phases of the project life cycle as “research” and “development”. Discussion and Conclusions: the foreign science

  8. Evaluation of a new automated instrument for pretransfusion testing.

    Science.gov (United States)

    Morelati, F; Revelli, N; Maffei, L M; Poretti, M; Santoro, C; Parravicini, A; Rebulla, P; Cole, R; Sirchia, G

    1998-10-01

    A number of automated devices for pretransfusion testing have recently become available. This study evaluated a fully automated device based on column agglutination technology (AutoVue System, Ortho, Raritan, NJ). Some 6747 tests including forward and reverse ABO group, Rh type and phenotype, antibody screen, autocontrol, and crossmatch were performed on random samples from 1069 blood donors, 2063 patients, and 98 newborns and cord blood. Also tested were samples from 168 immunized patients and 53 donors expressing weak or variant A and D antigens. Test results and technician times required for their performance were compared with those obtained by standard methods (manual column agglutination technology, slide, semiautomatic handler). No erroneous conclusions were found in regard to the 5028 ABO group and Rh type or phenotype determinations carried out with the device. The device rejected 1.53 percent of tests for sample inadequacy. Of the remaining 18 tests with discrepant results found with the device and not confirmed with the standard methods, 6 gave such results because of mixed-field reactions, 10 gave negative results with A2 RBCs in reverse ABO grouping, and 2 gave very weak positive reactions in antibody screening and crossmatching. In the samples from immunized patients, the device missed one weak anti-K, whereas standard methods missed five weak antibodies. In addition, 48, 34, and 31 of the 53 weak or variant antigens were detected by the device, the slide method, and the semiautomated handler, respectively. Technician time with the standard methods was 1.6 to 7 times higher than that with the device. The technical performance of the device compared favorably with that of standard methods, with a number of advantages, including in particular the saving of technician time. Sample inadequacy was the most common cause of discrepancy, which suggests that standardization of sample collection can further improve the performance of the device.

  9. Safely Transporting the assembled EUSO-SPB instrument 1000 miles for field testing

    Science.gov (United States)

    Cummings, Austin; Gregg, Rachael; Polonsky, Zach

    2017-01-01

    The EUSO-SPB instrument assembled and tested at Colorado School of Mines and then transported in this state to the Telescope Array site in Delta Utah for field tests. 6 hours after arrival the instrument recorded first light from a laser 20 km distant. We describe the structures and methods that we developed drive this instrument to the test site. The vibration data collected during the 1000 mile round trip and the lessons learned will also be presented. In our experience, there is relatively little quantitative information available about this type of critical operation.

  10. Analysis and application of electromagnetic compatibility test for safety instrumentation and control electronic equipment

    International Nuclear Information System (INIS)

    Hu Xuefeng; Zhou Liang; Zhang Longqiang

    2014-01-01

    The applicable qualification standard of electromagnetic compatibility (EMC) tests for instrumentation and control electronic equipment was introduced. The electromagnetic interference immunity test, the radiated radio-frequency electromagnetic field immunity test, the sensibility test, the source surge immunity test and the electrostatic discharge immunity test for EMC test were mainly introduced. And the important of configuration and the selection of method for EMC sampler was especially introduced. (authors)

  11. Neutron generator instrumentation at the Department 2350 Neutron Generator Test Facility

    International Nuclear Information System (INIS)

    Bryant, T.C.; Mowrer, G.R.

    1979-06-01

    The computer and waveform digitizing capability at the test facility has allowed several changes in the techniques used to test neutron generators. These changes include methods used to calibrate the instrumentation and changes in the operation of the test facility. These changes have increased the efficiency of the test facility as well as increasing both timing and amplitude accuracy of neutron generator waveforms

  12. A comparison of two reciprocating instruments using bending stress and cyclic fatigue tests

    Directory of Open Access Journals (Sweden)

    Pantaleo SCELZA

    2015-01-01

    Full Text Available The aim of this study was to comparatively evaluate the bending resistance at 45º, the static and dynamic cyclic fatigue life, and the fracture type of the WaveOne (Dentsply Maillefer, Ballaigues, Switzerland 25-08 and Reciproc (VDW, Munich, Germany 25-08 instruments. A total of 60 nickel-titanium (NiTi instruments (30 Reciproc and 30 WaveOne from three different lots, each of which was 25 mm in length, were tested. The bending resistance was evaluated through the results of a cantilever-bending test conducted using a universal testing machine. Static and dynamic cyclic fatigue testing was conducted using a custom-made device. For the static and dynamic tests, a cast Ni-Cr-Mo-Ti alloy metal block with an artificial canal measuring 1.77 mm in diameter and 20.00 mm in total length was used. A scanning electron microscope was used to determine the type of fracture. Statistical analyses were performed on the results. The WaveOne instrument was less flexible than the Reciproc (p < 0.05. The Reciproc instrument showed better resistance in the static and dynamic cyclic fatigue tests (p < 0.05. The transverse cross-section and geometry of the instruments were important factors in their resistance to bending and cyclic fracture. Both of the instruments showed ductile-type fracture characteristics. It can be concluded that the Reciproc 25-08 instrument was more resistant to static and dynamic cyclic fatigue than the WaveOne 25-08 instrument, while the WaveOne 25-08 instrument was less flexible. Bending and resistance to cyclic fracture were influenced by the instruments’ geometries and transverse cross-sections. Both of the instruments showed ductile-type fracture characteristics.

  13. The Hydraulic Test Report for Non-instrumented Irradiation Test Rig of DUO-Cooled Annular Pellet

    International Nuclear Information System (INIS)

    Kim, Dae Ho; Lee, Kang Hee; Shin, Chang Hwan; Yang, Yong Sik; Kim, Sun Ki; Bang, Je Geon; Song, Kun Woo

    2007-08-01

    This report presents the results of pressure drop test and vibration test for non-instrumented rig of Advanced PWR DUO-Fuel Annular Pellet which were designed and fabricated by KAERI. From the pressure drop test results, it is noted that the flow velocity across the non-instrumented rig of Advanced PWR DUO-Fuel Annular Pellet corresponding to the pressure drop of 200 kPa is measured to be about 8.30 kg/sec. Vibration frequency results for the non-instrumented rig at the pump spin frequency ranges from 19.0 to 32.0 Hz, RMS(Root Mean Square) displacement for the non-instrumented rig of Advanced PWR DUO-Fuel Annular Pellet is less than 7.25 m, and the maximum displacement is less than 31.27 μm. This test was performed at the FIVPET facility

  14. Evaluation of a draft standard on performance specifications for health physics instrumentation: results for environmental tests

    International Nuclear Information System (INIS)

    Kenoyer, J.L.; Swinth, K.L.; Mashburn, K.R.; Selby, J.M.

    1984-06-01

    Draft ANSI Standard N42.17 on performance specifications for health physics instrumentation is currently being evaluated by the Pacific Northwest Laboratory. Evaluation is performed by testing a cross-section of currently available instruments with testing procedures based on specifications of the standard and then determining the degree of conformance to the various elements of the proposed standard. Data will be presented on the performance of a cross-section of beta-gamma survey instruments under various environmental tests. Test results that will be presented include temperature effects, humidity effects, radio frequency (r.f.) susceptibility, ambient pressure effects, vibration effects, and shock effects. Tests performed to date show that most instruments will meet the temperature, humidity, and ambient pressure tests. A large variability is noted among instruments from the same or different vendors. Preliminary r.f. susceptibility tests have shown large artificial responses at some frequencies for specific instruments. The presentation will also include a discussion of procedures used in the testing and weaknesses identified in the proposed standard

  15. Ground tests of the Dynamic Albedo of Neutron instrument operation in the passive mode with a Martian soil model

    Science.gov (United States)

    Shvetsov, V. N.; Dubasov, P. V.; Golovin, D. V.; Kozyrev, A. S.; Krylov, A. R.; Krylov, V. A.; Litvak, M. L.; Malakhov, A. V.; Mitrofanov, I. G.; Mokrousov, M. I.; Sanin, A. B.; Timoshenko, G. N.; Vostrukhin, A. A.; Zontikov, A. O.

    2017-07-01

    The results of the Dynamic Albedo of Neutrons (DAN) instrument ground tests in the passive mode of operation are presented in comparison with the numerical calculations. These test series were conducted to support the current surface measurements of DAN onboard the MSL Curiosity rover. The instrument sensitivity to detect thin subsurface layers of water ice buried at different depths in the analog of Martian soil has been evaluated during these tests. The experiments have been done with a radioisotope Pu-Be neutron source (analog of the MMRTG neutron source onboard the Curiosity rover) and the Martian soil model assembled from silicon-rich window glass pane. Water ice layers were simulated with polyethylene sheets. All experiments have been performed at the test facility built at the Joint Institute for Nuclear Research (Dubna, Russia).

  16. Cryo-vacuum testing of the JWST Integrated Science Instrument Module (SPIE)

    Science.gov (United States)

    Kimble, Randy A.; Vila, M. Begona; Van Campen, Julie; Birkmann, Stephan M.; Comber, Brian J.; Fatig, Curtis C.; Glasse, Alistair C. H.; Glazer, Stuart D.; Kelly, Douglas M.; Mann, Steven D.; hide

    2016-01-01

    In late 2015/early 2016, a major cryo-vacuum test was carried out for the Integrated Science Instrument Module (ISIM) of the James Webb Space Telescope (JWST). This test comprised the final cryo-certification and calibration test of the ISIM, after its ambient environmental test program (vibration, acoustics, EMI/EMC), and before its delivery for integration with the rest of the JWST observatory. Over the 108-day period of the round-the-clock test program, the full complement of ISIM flight instruments, structure, harness radiator, and electronics were put through a comprehensive program of thermal, optical, electrical, and operational tests. The test verified the health and excellent performance of the instruments and ISIM systems, proving the ISIM element's readiness for integration with the telescope. We report here on the context, goals, setup, execution, and key results for this critical JWST milestone.

  17. Void fraction instrument software, Version 1,2, Acceptance test report

    International Nuclear Information System (INIS)

    Gimera, M.

    1995-01-01

    This provides the report for the void fraction instrument acceptance test software Version 1.2. The void fraction will collect data that will be used to calculate the quantity of gas trapped in waste tanks

  18. Causal null hypotheses of sustained treatment strategies: What can be tested with an instrumental variable?

    Science.gov (United States)

    Swanson, Sonja A; Labrecque, Jeremy; Hernán, Miguel A

    2018-05-02

    Sometimes instrumental variable methods are used to test whether a causal effect is null rather than to estimate the magnitude of a causal effect. However, when instrumental variable methods are applied to time-varying exposures, as in many Mendelian randomization studies, it is unclear what causal null hypothesis is tested. Here, we consider different versions of causal null hypotheses for time-varying exposures, show that the instrumental variable conditions alone are insufficient to test some of them, and describe additional assumptions that can be made to test a wider range of causal null hypotheses, including both sharp and average causal null hypotheses. Implications for interpretation and reporting of instrumental variable results are discussed.

  19. Physicists purchase materials testing machine in support of pioneering particle physics experiments

    CERN Multimedia

    Sharpe, Suzanne

    2007-01-01

    "The particle physics group at Liverpool University has purchased an LRXPlus singlecolumn materials testing machine from Lloyd Instruments, which will be used to help characterise the carbon-fibre support frames for detectors used for state-of-the-art particle physics experiments." (1 page)

  20. Environmental test chamber for the support of learning and teaching in intelligent control

    OpenAIRE

    Taylor, C. James

    2004-01-01

    The paper describes the utility of a low cost, 1 m2 by 2 m forced ventilation, micro-climate test chamber, for the support of research and teaching in mechatronics. Initially developed for the evaluation of a new ventilation rate controller, the fully instrumented chamber now provides numerous learning opportunities and individual projects for both undergraduate and postgraduate research students.

  1. Data acquisition during thermal test through virtual instrumentation

    Energy Technology Data Exchange (ETDEWEB)

    Pinto, Antonio Juscelino; Mourao, Rogerio Pimenta, E-mail: ajp@cdtn.br, E-mail: mouraor@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2013-07-01

    A package for the transport and long-term storage of irradiated fuel of research reactors is been developed by Argentina, Brazil and Chile through a regional cooperation project. In the scope of this project, a half-scale model of the package was designed, constructed and tested according to the IAEA regulations for the transport of radioactive materials. In order to acquire the temperatures developed during the prescribed thermal test, a dedicated data acquisition system was developed by the Centro de Desenvolvimento da Tecnologia Nuclear. The system was developed using the InduSoft Web Studio, a software platform which allows the development of HMI (Human Machine Interface) applications, and SCADA (Supervisory Control and Data Acquisition), a computer controlled system that monitors and controls industrial processes. The acquisition system's main components are the power supply source, two conversers, and the supervisor software InduSoft Web Studio. The sensors used were 5 m long Type K thermocouples with mineral isolation. Although developed for a specific application, the system can be used for temperature acquisition of diverse industrial processes. (author)

  2. Cryo-Vacuum Testing of the JWST Integrated Science Instrument Module

    Science.gov (United States)

    Kimble, Randy A.; Vila, M. Begona; Van Campen, Julie M.; Birkmann, Stephen M.; Comber, Brian J.; Fatig, Curtis C.; Glasse, Alistair C. H.; Glazer, Stuart D.; Kelly, Douglas M.; Mann, Steven D.; hide

    2016-01-01

    In late 2015 early 2016, a major cryo-vacuum test was carried out for the Integrated Science Instrument Module (ISIM) of the James Webb Space Telescope. This test comprised the final cryo-certification and calibration test of the ISIM before its delivery for integration with the rest of the JWST observatory. Over the roughly 100-day period of the round-the-clock test program, the full complement of ISIM flight instruments, structure, harness radiator, and electronics were put through a comprehensive program of thermal, optical, electrical, and operational tests. We briefly summarize the goals, setup, execution, and key results for this critical JWST milestone.

  3. The mechanical design and dynamic testing of the IBEX-H1 electrostatic analyzer spacecraft instrument

    Energy Technology Data Exchange (ETDEWEB)

    Bernardin, John D [Los Alamos National Laboratory; Baca, Allen G [SNL

    2009-01-01

    This paper presents the mechanical design, fabrication and dynamic testing of an electrostatic analyzer spacecraft instrument. The functional and environmental requirements combined with limited spacecraft accommodations, resulted in complex component geometries, unique material selections, and difficult fabrication processes. The challenging aspects of the mechanical design and several of the more difficult production processes are discussed. In addition, the successes, failures, and lessons learned from acoustic and random vibration testing of a full-scale prototype instrument are presented.

  4. Integrated Performance Testing for Nonproliferation Support Project

    Energy Technology Data Exchange (ETDEWEB)

    Johns, Russell; Bultz, Garl Alan; Byers, Kenneth R.; Yaegle, William

    2013-08-20

    The objective of this workshop is to provide participants with training in testing techniques and methodologies for assessment of the performance of: Physical Protection system elements; Material Control and Accounting (MC&A) system elements.

  5. High-speed instrumentation complex for car crash testing

    Science.gov (United States)

    Baranov, S. V.; Gorin, I. M.; Drozhbin, Yu. A.; Kuznetsov, A. A.; Ponomaryov, A. M.; Semyonov, V. B.; Udalov, V. V.

    1993-01-01

    One of the most important car checking problems consists in safety testing which includes trials for different types of collision, e.g., frontal and lateral. This allows us to study deformations of the automobile and its parts during the impact. To obtain reliable data on overloading, acceleration, deformation, force load on the car's body as well as on the anthropomorphic dummies inside it, use is made of rather a great number of different techniques. Highly informative among them is high-speed cine recording which allows us to register variations that occur during a fraction of a second, and then to reproduce with variable rate the frame images obtained. This makes it possible to study the impact parameters variations much more accurately.

  6. Static and fatigue biomechanical properties of anterior thoracolumbar instrumentation systems. A synthetic testing model.

    Science.gov (United States)

    Kotani, Y; Cunningham, B W; Parker, L M; Kanayama, M; McAfee, P C

    1999-07-15

    A mechanical testing standard for anterior thoracolumbar instrumentation systems was introduced, using a synthetic model. Twelve recent instrumentation systems were tested in static and fatigue modes. To establish the testing standard for anterior thoracolumbar instrumentation systems using a synthetic model and to evaluate the static and fatigue biomechanical properties of 12 anterior thoracolumbar instrumentation systems. Although numerous studies have been performed to evaluate the biomechanics of anterior spinal instrumentation using a cadaveric or animal tissue, problems of specimen variation, lack of reproducibility, and inability to perform fatigue testing have been pointed out. In no studies has a precise synthetic testing standard for anterior thoracolumbar instrumentation systems been described. An ultra-high-molecular-weight polyethylene cylinder was designed according to the anatomic dimensions of the vertebral body. Two cylinders spanned by spinal instrumentation simulated a total corpectomy defect, and a compressive lateral bending load was applied. The instrumentation assembly was precisely standardized. The static destructive and fatigue tests up to 2 million cycles at three load levels were conducted, followed by the failure mode analysis. Twelve anterior instrumentation systems, consisting of five plate and seven rod systems were compared in stiffness, bending strength, and cycles to failure. Static and fatigue test parameters both demonstrated highly significant differences between devices. The stiffness ranged from 280.5 kN/m in the Synthes plate (Synthes, Paoli, PA) to 67.9 kN/m in the Z-plate ATL (SofamorDanek, Memphis, TN). The Synthes plate and Kaneda SR titanium (AcroMed, Cleveland, OH) formed the highest subset in bending strength of 1516.1 N and 1209.9 N, respectively, whereas the Z-plate showed the lowest value of 407.3 N. There were no substantial differences between plate and rod devices. In fatigue, only three systems: Synthes plate

  7. Transfer of Training: Does It Truly Happen?: An Examination of Support, Instrumentality, Retention and Learner Readiness on the Transfer Motivation and Transfer of Training

    Science.gov (United States)

    Bhatti, Muhammad Awais; Battour, Mohamed Mohamed; Sundram, Veera Pandiyan Kaliani; Othman, Akmal Aini

    2013-01-01

    Purpose: The purpose of this study is to highlight the importance of selected environmental, situational and individual factors in the training transfer process. Design/methodology/approach: This study proposes and tests a framework via structural equation modelling by including supervisor and peer support, instrumentality and learner readiness on…

  8. A review of cyclic fatigue testing of nickel-titanium rotary instruments.

    Science.gov (United States)

    Plotino, Gianluca; Grande, Nicola M; Cordaro, Massimo; Testarelli, Luca; Gambarini, Gianluca

    2009-11-01

    Fractured rotary nickel-titanium (NiTi) instruments have been classified into those that fail as a result of cyclic flexural fatigue or torsional failure or a combination of both. Clinically, NiTi rotary instruments are subjected to both torsional load and cyclic fatigue, and ongoing research aims to clarify the relative contributions of both factors to instrument separation. To date, there is no specification or international standard to test cyclic fatigue resistance of endodontic rotary instruments. As a consequence, several devices and methods have been used to investigate in vitro cyclic fatigue fracture resistance of NiTi rotary endodontic instruments. In nearly all studies reported in the endodontic literature, the rotating instrument was either confined in a glass or metal tube, in a grooved block-and-rod assembly, or in a sloped metal block. There has been no mention of the "fit" of the instrument in the tube or groove. As the instrument is likely to be fitting loosely, the description of the radius of curvature in those studies is likely to be overstated (ie, the file was actually bent less severely than reported, adding a variability in the amount of flexural stress). This review analyzed several devices that have been used in endodontic literature for cyclic fatigue testing and found that differences in the methodology affected the fatigue behavior of rotary instruments and, consequently, the outcome of these studies. An international standard for cyclic fatigue testing of NiTi rotary instruments is required to ensure uniformity of methodology and comparable results.

  9. Instrumentation Report No. 2: identification, evaluation, and remedial actions related to transducer failures at the spent fuel test-climax

    Energy Technology Data Exchange (ETDEWEB)

    Patrick, W.C.; Carlson, R.C.; Rector, N.L.

    1981-11-30

    The Spent Fuel Test-Climax (SFT-C) is a test of the feasibility of safe and reliable short-term storage and retrieval of spent fuel from commercial nuclear reactors. In support of operational and technical goals of the test, about 850 channels of instrumentation have been installed at the SFT-C. Failure of several near-field instruments began less than six months after emplacement of 11 canisters of spent fuel and activation of six thermally similar simulators. The failed units were linear potentiometers (used to make displacement measurements) and vibrating wire stressmeters (used to make change-in-stress measurements). This report discusses the observed problems and remedial actions taken to date.

  10. A Perspective on Development Flight Instrumentation and Flight Test Analysis Plans for Ares I-X

    Science.gov (United States)

    Huebner, Lawrence D.; Richards, James S.; Brunty, Joseph A.; Smith, R. Marshall; Trombetta, Dominic R.

    2009-01-01

    NASA. s Constellation Program will take a significant step toward completion of the Ares I crew launch vehicle with the flight test of Ares I-X and completion of the Ares I-X post-flight evaluation. The Ares I-X flight test vehicle is an ascent development flight test that will acquire flight data early enough to impact the design and development of the Ares I. As the primary customer for flight data from the Ares I-X mission, Ares I has been the major driver in the definition of the Development Flight Instrumentation (DFI). This paper focuses on the DFI development process and the plans for post-flight evaluation of the resulting data to impact the Ares I design. Efforts for determining the DFI for Ares I-X began in the fall of 2005, and significant effort to refine and implement the Ares I-X DFI has been expended since that time. This paper will present a perspective in the development and implementation of the DFI. Emphasis will be placed on the process by which the list was established and changes were made to that list due to imposed constraints. The paper will also discuss the plans for the analysis of the DFI data following the flight and a summary of flight evaluation tasks to be performed in support of tools and models validation for design and development.

  11. Analysis instrument test on mathematical power the material geometry of space flat side for grade 8

    Science.gov (United States)

    Kusmaryono, Imam; Suyitno, Hardi; Dwijanto, Karomah, Nur

    2017-08-01

    The main problem of research to determine the quality of test items on the material side of flat geometry to assess students' mathematical power. The method used is quantitative descriptive. The subjects were students of class 8 as many as 20 students. The object of research is the quality of test items in terms of the power of mathematics: validity, reliability, level of difficulty and power differentiator. Instrument mathematical power ratings are tested include: written tests and questionnaires about the disposition of mathematical power. Data were obtained from the field, in the form of test data on the material geometry of space flat side and questionnaires. The results of the test instrument to the reliability of the test item is influenced by many factors. Factors affecting the reliability of the instrument is the number of items, homogeneity test questions, the time required, the uniformity of conditions of the test taker, the homogeneity of the group, the variability problem, and motivation of the individual (person taking the test). Overall, the evaluation results of this study stated that the test instrument can be used as a tool to measure students' mathematical power.

  12. Fabrication and Testing of a Modular Micro-Pocket Fission Detector Instrumentation System for Test Nuclear Reactors

    Science.gov (United States)

    Reichenberger, Michael A.; Nichols, Daniel M.; Stevenson, Sarah R.; Swope, Tanner M.; Hilger, Caden W.; Roberts, Jeremy A.; Unruh, Troy C.; McGregor, Douglas S.

    2018-01-01

    Advancements in nuclear reactor core modeling and computational capability have encouraged further development of in-core neutron sensors. Measurement of the neutron-flux distribution within the reactor core provides a more complete understanding of the operating conditions in the reactor than typical ex-core sensors. Micro-Pocket Fission Detectors have been developed and tested previously but have been limited to single-node operation and have utilized highly specialized designs. The development of a widely deployable, multi-node Micro-Pocket Fission Detector assembly will enhance nuclear research capabilities. A modular, four-node Micro-Pocket Fission Detector array was designed, fabricated, and tested at Kansas State University. The array was constructed from materials that do not significantly perturb the neutron flux in the reactor core. All four sensor nodes were equally spaced axially in the array to span the fuel-region of the reactor core. The array was filled with neon gas, serving as an ionization medium in the small cavities of the Micro-Pocket Fission Detectors. The modular design of the instrument facilitates the testing and deployment of numerous sensor arrays. The unified design drastically improved device ruggedness and simplified construction from previous designs. Five 8-mm penetrations in the upper grid plate of the Kansas State University TRIGA Mk. II research nuclear reactor were utilized to deploy the array between fuel elements in the core. The Micro-Pocket Fission Detector array was coupled to an electronic support system which has been specially developed to support pulse-mode operation. The Micro-Pocket Fission Detector array composed of four sensors was used to monitor local neutron flux at a constant reactor power of 100 kWth at different axial locations simultaneously. The array was positioned at five different radial locations within the core to emulate the deployment of multiple arrays and develop a 2-dimensional measurement of

  13. Fabrication and Testing of a Modular Micro-Pocket Fission Detector Instrumentation System for Test Nuclear Reactors

    Directory of Open Access Journals (Sweden)

    Reichenberger Michael A.

    2018-01-01

    Full Text Available Advancements in nuclear reactor core modeling and computational capability have encouraged further development of in-core neutron sensors. Measurement of the neutron-flux distribution within the reactor core provides a more complete understanding of the operating conditions in the reactor than typical ex-core sensors. Micro-Pocket Fission Detectors have been developed and tested previously but have been limited to single-node operation and have utilized highly specialized designs. The development of a widely deployable, multi-node Micro-Pocket Fission Detector assembly will enhance nuclear research capabilities. A modular, four-node Micro-Pocket Fission Detector array was designed, fabricated, and tested at Kansas State University. The array was constructed from materials that do not significantly perturb the neutron flux in the reactor core. All four sensor nodes were equally spaced axially in the array to span the fuel-region of the reactor core. The array was filled with neon gas, serving as an ionization medium in the small cavities of the Micro-Pocket Fission Detectors. The modular design of the instrument facilitates the testing and deployment of numerous sensor arrays. The unified design drastically improved device ruggedness and simplified construction from previous designs. Five 8-mm penetrations in the upper grid plate of the Kansas State University TRIGA Mk. II research nuclear reactor were utilized to deploy the array between fuel elements in the core. The Micro-Pocket Fission Detector array was coupled to an electronic support system which has been specially developed to support pulse-mode operation. The Micro-Pocket Fission Detector array composed of four sensors was used to monitor local neutron flux at a constant reactor power of 100 kWth at different axial locations simultaneously. The array was positioned at five different radial locations within the core to emulate the deployment of multiple arrays and develop a 2-dimensional

  14. German tests in support of code validation

    International Nuclear Information System (INIS)

    Clausmeyer, H.; Maile, K.

    1995-01-01

    This paper documents some of the most important code verifications and validation trials related to the different nuclear reactor concepts namely light water reactors (LWR), liquid metal fast breeder reactors (LMFBR) and high temperature reactors (HTR), respectively. Selected experimental and theoretical investigations demonstrate the effectiveness of those efforts which contribute either to a better understanding of the nuclear codes or to initiate necessary changes. Resistance against crack initiation, crack propagation and crack arrest are treated by linear elastic fracture mechanics for pressure vessels, tubes, plates and pipes submitted to tensile load, internal pressure or bending moment. Different test parameters are taken into account such as: materials composition, temperature, strain rate, surface roughness, notches, weldments etc. Test results are compared to calculation predictions and calculation of fracture mechanics parameters for a feedback to the code. (J.S.). 21 refs., 28 figs., 5 tabs

  15. Hydraulic test for non-instrumented capsule of advanced PWR fuel pellet

    International Nuclear Information System (INIS)

    Jun, Hyung Gil; Yoon, Y. J.; Chun, S. Y.; Kim, D. H.; Lee, C. B.; Ryu, J.

    2001-04-01

    This report presents the results of pressure drop test, vibration test and endurance test for Non-instrumented Capsule of Advanced PWR Fuel Pellet which were designed fabricated by KAERI. From the pressure drop test results, it is noted that the flow rate across the Non-instrumented Capsule of Advanced PWR Fuel Pellet corresponding to the pressure drop of 200 kPa is measured to be about 7.45 kg/sec. Vibration frequency for the Non-instrumented Capsule of Advanced PWR Fuel Pellet ranges from 13.0 to 32.3 Hz. RMS(Root Mean Square) displacement for the fuel rig is less than 11.6 μm, and the maximum displacement is less than 30.5 μm. The endurance test was carried out for 103 days and 17 hours

  16. Prescribing tests must have curriculum support

    Directory of Open Access Journals (Sweden)

    Lemon TI

    2013-05-01

    Full Text Available Rupali D Shah, Thomas I LemonSchool of Medicine, Cardiff University, University Hospital of Wales, Cardiff, WalesGordon, Catchpole and Baker1 have discussed and investigated a very interesting, currently relevant, subject in medical education; particularly with the introduction of the prescribing test for undergraduates trialled in the UK this year and set to become a fully-fledged part of the curriculum and assessment criteria for 2014 graduates.2 It would of course be of great interest to compare the themes discussed in this paper and see they how would compare to recent graduates in late 2014.View original paper by Gordon and colleagues.

  17. Measuring the Impact of Students' Social Relations and Values: Validation of the Social-Relational Support for Education Instrument

    Science.gov (United States)

    Vickers, Margaret; Finger, Linda; Barker, Katrina; Bodkin-Andrews, Gawaian

    2014-01-01

    A significant body of literature attests to the influence of social contexts on students' engagement with school. A review of this literature led to the construction of a self-report instrument designed to measure Social-Relational Support for Education (SRSE). The conceptual framework underlying the SRSE instrument focuses on the factors that can…

  18. Test - retest reliability of two instruments for measuring public attitudes towards persons with mental illness

    Directory of Open Access Journals (Sweden)

    Leufstadius Christel

    2011-01-01

    Full Text Available Abstract Background Research has identified stigmatization as a major threat to successful treatment of individuals with mental illness. As a consequence several anti-stigma campaigns have been carried out. The results have been discouraging and the field suffers from lack of evidence about interventions that work. There are few reports on psychometric data for instruments used to assess stigma, which thus complicates research efforts. The aim of the present study was to investigate test-retest reliability of the Swedish versions of the questionnaires: FABI and "Changing Minds" and to examine the internal consistency of the two instruments. Method Two instruments, fear and behavioural intentions (FABI and "Changing Minds", used in earlier studies on public attitudes towards persons with mental illness were translated into Swedish and completed by 51 nursing students on two occasions, with an interval of three weeks. Test-retest reliability was calculated by using weighted kappa coefficient and internal consistency using the Cronbach's alpha coefficient. Results Both instruments attain at best moderate test-retest reliability. For the Changing Minds questionnaire almost one fifth (17.9% of the items present poor test-retest reliability and the alpha coefficient for the subscales ranges between 0.19 - 0.46. All of the items in the FABI reach a fair or a moderate agreement between the test and retest, and the questionnaire displays a high internal consistency, alpha 0.80. Conclusions There is a need for development of psychometrically tested instruments within this field of research.

  19. Developing an Instrumentation Package for in-Water Testing of Marine Hydrokinetic Energy Devices: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, E.

    2010-08-01

    The ocean-energy industry is still in its infancy and device developers have provided their own equipment and procedures for testing. Currently, no testing standards exist for ocean energy devices in the United States. Furthermore, as prototype devices move from the test tank to in-water testing, the logistical challenges and costs grow exponentially. Development of a common instrumentation package that can be moved from device to device is one means of reducing testing costs and providing normalized data to the industry as a whole. As a first step, the U.S. National Renewable Energy Laboratory (NREL) has initiated an effort to develop an instrumentation package to provide a tool to allow common measurements across various ocean energy devices. The effort is summarized in this paper. First, we present the current status of ocean energy devices. We then review the experiences of the wind industry in its development of the instrumentation package and discuss how they can be applied in the ocean environment. Next, the challenges that will be addressed in the development of the ocean instrumentation package are discussed. For example, the instrument package must be highly adaptable to fit a large array of devices but still conduct common measurements. Finally, some possible system configurations are outlined followed by input from the industry regarding its measurement needs, lessons learned from prior testing, and other ideas.

  20. The Communication Supports Inventory-Children & Youth (CSI-CY), a new instrument based on the ICF-CY.

    Science.gov (United States)

    Rowland, Charity; Fried-Oken, Melanie; Bowser, Gayl; Granlund, Mats; Lollar, Donald; Phelps, Randall; Simeonsson, Rune J; Steiner, Sandra A M

    2016-09-01

    Two studies are presented that evaluated the Communication Supports Inventory-Children & Youth (CSI-CY), an instrument designed to facilitate the development of communication-related educational goals for students with complex communication needs (CCN). The CSI-CY incorporates a code set based on the ICF-CY. The studies were designed to determine the effect of using the CSI-CY on IEP goals for students with CCN and to evaluate consumer satisfaction. In Study 1, sixty-one educators and speech-language pathologists were randomly assigned to either (a) provide a student's current IEP (control group) or (b) complete the CSI-CY prior to preparing a student's next IEP and to submit the new IEP (experimental group). Study 2 was a field test to generate consumer satisfaction data. Study 1 showed that IEP goals submitted by participants in the experimental group referenced CSI-CY-related content significantly more frequently than did those submitted by control participants. Study 2 revealed high satisfaction with the instrument. The code set basis of the CSI-CY extends the common language of the ICF-CY to practical educational use for children with CCN across diagnostic groups. The CSI-CY is well regarded as an instrument to inform the content of communication goals related to CCN. Implications for Rehabilitation The CSI-CY will guide rehabilitation professionals to develop goals for children with complex communication impairments. The CSI-CY is a new instrument that is based on the ICF-CY for documentation of communication goals.

  1. Electronic constant current and current pulse signal generator for nuclear instrumentation testing

    Science.gov (United States)

    Brown, R.A.

    1994-04-19

    Circuitry is described for testing the ability of an intermediate range nuclear instrument to detect and measure a constant current and a periodic current pulse. The invention simulates the resistance and capacitance of the signal connection of a nuclear instrument ion chamber detector and interconnecting cable. An LED flasher/oscillator illuminates an LED at a periodic rate established by a timing capacitor and circuitry internal to the flasher/oscillator. When the LED is on, a periodic current pulse is applied to the instrument. When the LED is off, a constant current is applied. An inductor opposes battery current flow when the LED is on. 1 figures.

  2. Calibration and Application of the Field Instruments of a Fuel Test Loop

    International Nuclear Information System (INIS)

    Choi, Young-San; In, Won-Ho; Bae, Sang-Hoon; Kim, Sang-Jin; Jung, Hoan-Sung

    2007-01-01

    The Fuel Test Loop in HANARO is now in commissioning. The field instruments of the FTL were selected to secure stability and reliability of signals and they were self calibrated by the plant prior to the installation. The field instruments consist of thermometer, flowmeter, manometer, level meter and analyzer, and the standard measuring devices used for calibration were certified by the national calibration laboratory before use. This paper describes the calibration methods and results of field instruments for each parameter as well as any particulars and corrections identified during calibration. Also, it describes problems in using standard measuring devices employed for calibration

  3. Development of hybrid electric vehicle powertrain test system based on virtue instrument

    Science.gov (United States)

    Xu, Yanmin; Guo, Konghui; Chen, Liming

    2017-05-01

    Hybrid powertrain has become the standard configuration of some automobile models. The test system of hybrid vehicle powertrain was developed based on virtual instrument, using electric dynamometer to simulate the work of engines, to test the motor and control unit of the powertrain. The test conditions include starting, acceleration, and deceleration. The results show that the test system can simulate the working conditions of the hybrid electric vehicle powertrain under various conditions.

  4. Ground tests with active neutron instrumentation for the planetary science missions

    International Nuclear Information System (INIS)

    Litvak, M.L.; Mitrofanov, I.G.; Sanin, A.B.; Jun, I.; Kozyrev, A.S.; Krylov, A.; Shvetsov, V.N.; Timoshenko, G.N.; Starr, R.; Zontikov, A.

    2015-01-01

    We present results of experimental work performed with a spare flight model of the DAN/MSL instrument in a newly built ground test facility at the Joint Institute for Nuclear Research. This instrument was selected for the tests as a flight prototype of an active neutron spectrometer applicable for future landed missions to various solid solar system bodies. In our experiment we have fabricated simplified samples of planetary material and tested the capability of neutron activation methods to detect thin layers of water/water ice lying on top of planetary dry regolith or buried within a dry regolith at different depths

  5. Evaluation of hydrogen embrittlement and temper embrittlement by key curve method in instrumented Charpy test

    Directory of Open Access Journals (Sweden)

    Makita A.

    2010-06-01

    Full Text Available Instrumented Charpy test was conducted on small sized specimen of 21/4Cr-1Mo steel. In the test the single specimen key curve method was applied to determine the value of fracture toughness for the initiation of crack extension with hydrogen free, KIC, and for hydrogen embrittlement cracking, KIH. Also the tearing modulus as a parameter for resistance to crack extension was determined. The role of these parameters was discussed at an upper shelf temperature and at a transition temperature. Then the key curve method combined with instrumented Charpy test was proven to be used to evaluate not only temper embrittlement but also hydrogen embrittlement.

  6. Cryo-Vacuum Testing of the Integrated Science Instrument Module for the James Webb Space Telescope

    Science.gov (United States)

    Kimble, Randy A.; Davila, P. S.; Drury, M. P.; Glazer, S. D.; Krom, J. R.; Lundquist, R. A.; Mann, S. D.; McGuffey, D. B.; Perry, R. L.; Ramey, D. D.

    2011-01-01

    With delivery of the science instruments for the James Webb Space Telescope (JWST) to Goddard Space Flight Center (GSFC) expected in 2012, current plans call for the first cryo-vacuum test of the Integrated Science Instrument Module (ISIM) to be carried out at GSFC in early 2013. Plans are well underway for conducting this ambitious test, which will perform critical verifications of a number of optical, thermal, and operational requirements of the IS 1M hardware, at its deep cryogenic operating temperature. We describe here the facilities, goals, methods, and timeline for this important Integration & Test milestone in the JWST program.

  7. The collection and analysis of transient test data using the mobile instrumentation data acquisition system (MIDAS)

    International Nuclear Information System (INIS)

    Uncapher, W.L.; Arviso, M.

    1995-01-01

    Packages designed to transport radioactive materials are required to survive exposure to environments defined in Code of Federal Regulations. Cask designers can investigate package designs through structural and thermal testing of full-scale packages, components, or representative models. The acquisition of reliable response data from instrumentation measurement devices is an essential part of this testing activity. Sandia National Laboratories, under the sponsorship of the US Department of Energy (DOE), has developed the Mobile Instrumentation Data Acquisition System (MIDAS) dedicated to the collection and processing of structural and thermal data from regulatory tests

  8. Food-related life styles in Singapore: Testing a Western European research instrument in Southeast Asia

    DEFF Research Database (Denmark)

    Askegaard, Søren; Brunsø, Karen; Crippen, Kaye

    , and to interpret similarities and differences found. For this purpose, data have been collected in Singaporean families using the food-related life style instrument. A total of 89 questionnaires form the basis of the analysis. First, the cross-cultural validity of the instrument is tested, and secondly......, in the light of those results, we interpret the results in relationship to local food cultures....

  9. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid Q

    International Nuclear Information System (INIS)

    KOCH, M.R.

    2000-01-01

    This Test Plan provides a test method to dedicate the leak detection relays used on the new Pumping Instrumentation and Control (PIC) skids. The new skids are fabricated on-site. The leak detection system is a safety class system per the Authorization Basis

  10. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid ''P''

    International Nuclear Information System (INIS)

    KOCH, M.R.

    2000-01-01

    This Test Plan provides a test method to dedicate the leak detection relays used on the new Pumping Instrumentation and Control (PIC) skids. The new skids are fabricated on-site. The leak detection system is a safety class system per the Authorization Basis

  11. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid ''V''

    International Nuclear Information System (INIS)

    KOCH, M.R.

    2000-01-01

    This Acceptance Test Procedure (ATP) verifies proper construction per the design drawings and tests for proper functioning of the Pumping Instrumentation and Control (PIC) skid ''V''. The scope section lists the systems and functions to be checked. This ATP will be performed at the Site Fabrication Services (SFS) shop upon completion of the construction of the PIC skid

  12. Instrumented impact testing of kenaf fiber reinforced polypropylene composites: effects of temperature and composition

    Science.gov (United States)

    Craig Merrill Clemons; Anand R. Sanadi

    2007-01-01

    An instrumented Izod test was used to investigate the effects of fiber content, coupling agent, and temperature on the impact performance of kenaf fiber reinforced polypropylene (PP). Composites containing 0-60% (by weight) kenaf fiber and 0 or 2% maleated polypropylene (MAPP) and PP/wood flour composites were tested at room temperature and between -50 °C and +...

  13. Weak instrument robust tests in GMM and the new Keynesian Phillips curve

    NARCIS (Netherlands)

    Kleibergen, F.; Mavroeidis, S.

    2009-01-01

    We discuss weak instrument robust statistics in GMM for testing hypotheses on the full parameter vector or on subsets of the parameters. We use these test procedures to reexamine the evidence on the new Keynesian Phillips curve model. We find that U.S. postwar data are consistent with the view that

  14. Explaining perceived oral texture of starch-based custard desserts from standard and novel instrumental tests

    NARCIS (Netherlands)

    Wijk, R.A.de; Prinz, J.F.; Janssen, A.M.

    2006-01-01

    A number of in vitro and in vivo instrumental tests have been developed to reflect various aspects of the perceived oral texture of starch-based vanilla custard desserts. These tests include measurements of the food's infra-red reflectance (IRR), of the turbidity of spat-out rinse water, and of the

  15. Cryo Testing of tbe James Webb Space Telescope's Integrated Science Instrument Module

    Science.gov (United States)

    VanCampen, Julie

    2004-01-01

    The Integrated Science Instrument Module (ISIM) of the James Webb Space Telescope will be integrated and tested at the Environmental Test Facilities at Goddard Space Flight Center (GSFC). The cryogenic thermal vacuum testing of the ISIM will be the most difficult and problematic portion of the GSFC Integration and Test flow. The test is to validate the coupled interface of the science instruments and the ISIM structure and to sufficiently stress that interface while validating image quality of the science instruments. The instruments and the structure are not made from the same materials and have different CTE. Test objectives and verification rationale are currently being evaluated in Phase B of the project plan. The test program will encounter engineering challenges and limitations, which are derived by cost and technology many of which can be mitigated by facility upgrades, creative GSE, and thorough forethought. The cryogenic testing of the ISIM will involve a number of risks such as the implementation of unique metrology techniques, mechanical, electrical and optical simulators housed within the cryogenic vacuum environment. These potential risks are investigated and possible solutions are proposed.

  16. Instrumentation Technologies for Improving an Irradiation Testing of Nuclear Fuels and Materials at the HANARO

    International Nuclear Information System (INIS)

    Kim, Bong Goo; Park, Sung Jae; Choo, Ki Nam

    2011-01-01

    Over 50 years of nuclear fuels and materials irradiation testing has led to many countries developing significant improvements in instrumentation to monitor physical parameters and to control the test conditions in Materials Test Reactors (MTRs) or research reactors. Recent effort to deploy new fuels and materials in existing and advanced reactors has increased the demand for well-instrumented irradiation tests. Specifically, demand has increased for tests with sensors capable of providing real-time measurement of key parameters, such as temperature, geometry changes, thermal conductivity, fission gas release, cracking, coating buildup, thermal and fast flux, etc. This review paper documents the current state of instrumentation technologies in MTRs in the world and summarizes on-going research efforts to deploy new sensors. There is increased interest to irradiate new materials and reactor fuels for advanced PWRs and the Gen-IV reactor systems, such as SFRs (Sodium-cooled Fast Reactors), VHTRs (Very-High-Temperature Reactors), SCWRs (Supercritical-Water-cooled Reactors) and GFRs (Gas-cooled Fast Reactor). This review documents the current state of instrumentation technologies in MTRs in the world, identifies challenges faced by previous testing methods and how these challenges were overcome. A wide range of sensors are available to measure key parameters of interest during fuels and materials irradiations in MTRs. Such sensors must be reliable, small size, highly accurate, and able to withstand harsh conditions. On-going development efforts are focusing on providing MTR users a wider range of parameter measurements with increased accuracy. In addition, development efforts are focusing on reducing the impact of sensor on measurements by reducing sensor size. This report includes not only status of instrumentation using research reactors in the world to irradiate nuclear fuels and materials but also future directions relating to instrumentation technologies for

  17. Intrinsic or Instrumental Support for Democracy in a Post-Communist Society. The Case of Serbia

    Directory of Open Access Journals (Sweden)

    Zoran Pavlović

    2014-01-01

    Full Text Available According to the cultural model of political culture and political change, citizens accept only those political and economic structures compatible with their relatively stable cultural orientations and political values, which are product of a common early socialization. An important implication of this view is that, after several decades of authoritarian rule and a lack of democratic political culture, the support for democracy in ex-communist societies is rather instrumental than intrinsic, based not on values, but perceived system performances in political and economic terms. The rational choice (or institutional model, on the other hand, posits that these evaluations of system performances are far more than just lip service to democracy; they shape the political attitudes and behaviours and contribute to the (lack of allegiance to democratic institutions and norms. This paper aims at clarifying the importance of certain “institutional” and “cultural” variables for the general support to democracy in Serbia and their dynamic interplay. The data used in the paper were collected in the post-election survey, conducted after the May 2012 parliamentary and presidential elections on a representative sample of Serbian citizens (N=1,568. The relative importance of several predictors was analyzed: the socio-demographic variables (respondent’s age, educational level, monthly household income, the personality/dispositional variables (authoritarianism, the institutional variables (satisfaction with Serbian democracy and economy, evaluation of government performance before the election, the perceived level of respect for individual freedom and the quality of voters’ view representation in elections and the cultural variables (political tolerance, nationalism, liberalism, socialist egalitarianism. The most important predictors of support for democracy were satisfaction with Serbian democracy (β=.21, p<.001 and evaluation of government

  18. Measurement techniques and instruments suitable for life-prediction testing of photovoltaic arrays. Interim report

    Energy Technology Data Exchange (ETDEWEB)

    Noel, G.T.; Sliemers, F.A.; Deringer, G.C.; Wood, V.E.; Wilkes, K.E.; Gaines, G.B.; Carmichael, D.C.

    1978-01-15

    The validation of a service life of 20 years for low-cost photovoltaic arrays must be accomplished through accelerated life-prediction tests. A methodology for such tests has been developed in a preceding study. The results discussed consist of the initial identification and assessment of all known measurement techniques and instruments that might be used in these life-prediction tests. Array failure modes, relevant materials property changes, and primary degradation mechanisms are discussed as a prerequisite to identifying suitable measurement techniques and instruments. Candidate techniques and instruments are identified on the basis of extensive reviews of published and unpublished information. These methods are organized in six measurement categories--chemical, electrical, optical, thermal, mechanical, and ''other physicals''. Using specified evaluation criteria, the most promising techniques and instruments for use in life-prediction tests of arrays are then selected. These recommended techniques and their characteristics are described. Recommendations are made regarding establishment of the adequacy, particularly with respect to precision, of the more fully developed techniques for this application, and regarding the experimental evaluation of promising developmental techniques. Measurement needs not satisfied by presently available techniques/instruments are also identified.

  19. Performing T-tests to Compare Autocorrelated Time Series Data Collected from Direct-Reading Instruments.

    Science.gov (United States)

    O'Shaughnessy, Patrick; Cavanaugh, Joseph E

    2015-01-01

    Industrial hygienists now commonly use direct-reading instruments to evaluate hazards in the workplace. The stored values over time from these instruments constitute a time series of measurements that are often autocorrelated. Given the need to statistically compare two occupational scenarios using values from a direct-reading instrument, a t-test must consider measurement autocorrelation or the resulting test will have a largely inflated type-1 error probability (false rejection of the null hypothesis). A method is described for both the one-sample and two-sample cases which properly adjusts for autocorrelation. This method involves the computation of an "equivalent sample size" that effectively decreases the actual sample size when determining the standard error of the mean for the time series. An example is provided for the one-sample case, and an example is given where a two-sample t-test is conducted for two autocorrelated time series comprised of lognormally distributed measurements.

  20. The Influence of Instrumented Striker Configuration on the Results of Dynamic Toughness Testing

    International Nuclear Information System (INIS)

    Lucon, E.

    2008-01-01

    Several studies are available on the influence of the edge radius of instrumented strikers (ASTM - 8 mm or ISO - 2 mm) on the results of both non instrumented and instrumented Charpy tests. This paper investigates the effect of using either a 2 mm or a 8 mm striker when performing dynamic toughness tests at impact loading rates on precracked Charpy specimens. Existing data from tests run in the ductile-to-brittle region (dynamic Master Curve reference temperature) and in the upper shelf regime (ductile initiation fracture toughness and crack resistance curves) have been analyzed. The results show that 2 mm strikers tend to yield lower cleavage fracture toughness in the transition region (although the effect cannot be considered statistically significant), whereas the influence of striker configuration is negligible in the upper shelf regime when data are generated using the low-blow multiple-specimen technique.

  1. The Influence of Instrumented Striker Configuration on the Results of Dynamic Toughness Testing

    Energy Technology Data Exchange (ETDEWEB)

    Lucon, E.

    2008-09-15

    Several studies are available on the influence of the edge radius of instrumented strikers (ASTM - 8 mm or ISO - 2 mm) on the results of both non instrumented and instrumented Charpy tests. This paper investigates the effect of using either a 2 mm or a 8 mm striker when performing dynamic toughness tests at impact loading rates on precracked Charpy specimens. Existing data from tests run in the ductile-to-brittle region (dynamic Master Curve reference temperature) and in the upper shelf regime (ductile initiation fracture toughness and crack resistance curves) have been analyzed. The results show that 2 mm strikers tend to yield lower cleavage fracture toughness in the transition region (although the effect cannot be considered statistically significant), whereas the influence of striker configuration is negligible in the upper shelf regime when data are generated using the low-blow multiple-specimen technique.

  2. Meteorological Support Interface Control Working Group (MSICWG) Instrumentation, Data Format, and Networks Document

    Science.gov (United States)

    Brenton, James; Roberts, Barry C.

    2017-01-01

    The purpose of this document is to provide an overview of instrumentation discussed at the Meteorological Interface Control Working Group (MSICWG), a reference for data formats currently used by members of the group, a summary of proposed formats for future use by the group, an overview of the data networks of the group's members. This document will be updated as new systems are introduced, old systems are retired, and when the MSICWG community necessitates a change to the formats. The MSICWG consists of personnel from the National Aeronautics and Space Administration (NASA) Kennedy Space Center (KSC), NASA Marshall Space Flight Center (MSFC), NASA Johnson Space Center (JSC), National Oceanic and Atmospheric Administration National Weather Service Spaceflight Meteorology Group (SMG), and the United States Air Force (USAF) 45th Space Wing and Weather Squadron. The purpose of the group is to coordinate the distribution of weather related data to support NASA space launch related activities.

  3. INSTRUMENTS USED TO SUPPORT ACTIVE SALES IN THE COMPANY OF FOOD ECONOMY – A CASE STUDY

    Directory of Open Access Journals (Sweden)

    Agnieszka Piotrowska

    2015-06-01

    Full Text Available Changing environment requires enterprises to meet the needs of customers. Being on the market, survival and development of the company are determined not only by well qualifi ed staff but above all a happy customer. Therefore, it is important to use appropriate instruments to support active sales of the company. The study was conducted among 64 employees working in the organization studied. The study aimed to assess the knowledge and expertise of the staff in terms of the tools used in the enterprise for communication with the market. The study shows that the company has a well-developed system of communication with the market. Advertising agents that are used in the audited company are primarily the Internet, magazines, and outdoor advertising. Company’s gadgets are as well as awards for regular customers are the most popular among the target group consumer promotion tools.

  4. Design and Fabrication of the Double Cladding Instrumented Fuel Rods and the Instrumented Fuel Capsule(07F-06K) for the Irradiation Test at HANARO

    International Nuclear Information System (INIS)

    Sohn, Jae Min; Oh, Jong Myung; Oh, Soo Yeol; Park, Sung Jae; Sho, Man Soon; Kim, Bong Goo; Choo, Kee Nam; Kim, Young Ki

    2009-01-01

    An instrumented capsule for a nuclear fuel irradiation test (hereinafter referred to as 'instrumented fuel capsule'), which is crucial for the verification of a nuclear fuel performance and safety, has been developed to measure the fuel characteristics, such as the centerline and surface temperatures of the nuclear fuel, the internal pressure of a fuel rod, the elongation of the fuel pellet and the neutron fluxes during an irradiation test at HANARO(High-flux Advanced Neutron Application Reactor). The irradiation test of the first instrumented fuel capsule(02F-11K) was carried out for verification test at HANARO in March 2003. Through the irradiation tests of the some capsules, the design specifications and safety of the instrumented fuel capsule were verified successfully. And the dual instrumented fuel rods, which allow for two characteristics to be measured simultaneously in one fuel rod, have been developed to enhance the efficiency of the irradiation test using the instrumented fuel capsule. In this paper, we designed and fabricated a double cladding fuel rod to control the high temperature of nuclear fuels during an irradiation test at HANARO. And we design an instrumented fuel capsule(07F-06K) for an irradiation test of the double cladding fuel rods. We have designed and fabricated the double cladding fuel rod mockups and performed the out-pile tests using these mockups. The purposes of the out-pile tests were to analyze an effect of a gap size(between an outer cladding and an inner cladding) on the temperature and the effect of a mixture ratio of helium gas and neon gas on the temperature. Through the results of the out-pile tests, we have obtained the effects of a gap size and a gas mixture ratio on the temperature of nuclear fuels. Therefore an double cladding fuel rod and the 07F- 06K instrumented fuel capsule were designed on the base of the results of the out-pile tests using the mockups

  5. Design and Evaluation of a Prompting Instrument to Support Learning within the Diffusion Simulation Game

    Science.gov (United States)

    Kwon, Seolim; Lara, Miguel; Enfield, Jake; Frick, Theodore

    2013-01-01

    Conducting an iterative usability testing, a set of prompts used as a form of instructional support was developed in order to facilitate the comprehension of the diffusion of innovations theory (Rogers, 2003) in a simulation game called the Diffusion Simulation Game (DSG) (Molenda & Rice, 1979). The six subjects who participated in the study…

  6. Methods and Models of Market Risk Stress-Testing of the Portfolio of Financial Instruments

    Directory of Open Access Journals (Sweden)

    Alexander M. Karminsky

    2015-01-01

    Full Text Available Amid instability of financial markets and macroeconomic situation the necessity of improving bank risk-management instrument arises. New economic reality defines the need for searching for more advanced approaches of estimating banks vulnerability to exceptional, but plausible events. Stress-testing belongs to such instruments. The paper reviews and compares the models of market risk stress-testing of the portfolio of different financial instruments. These days the topic of the paper is highly acute due to the fact that now stress-testing is becoming an integral part of anticrisis risk-management amid macroeconomic instability and appearance of new risks together with close interest to the problem of risk-aggregation. The paper outlines the notion of stress-testing and gives coverage of goals, functions of stress-tests and main criteria for market risk stress-testing classification. The paper also stresses special aspects of scenario analysis. Novelty of the research is explained by elaborating the programme of aggregated complex multifactor stress-testing of the portfolio risk based on scenario analysis. The paper highlights modern Russian and foreign models of stress-testing both on solo-basis and complex. The paper lays emphasis on the results of stress-testing and revaluations of positions for all three complex models: methodology of the Central Bank of stress-testing portfolio risk, model relying on correlations analysis and copula model. The models of stress-testing on solo-basis are different for each financial instrument. Parametric StressVaR model is applicable to shares and options stress-testing;model based on "Grek" indicators is used for options; for euroobligation regional factor model is used. Finally some theoretical recommendations about managing market risk of the portfolio are given.

  7. The test beamline of the European Spallation Source - Instrumentation development and wavelength frame multiplication

    DEFF Research Database (Denmark)

    Woracek, R.; Hofmann, T.; Bulat, M.

    2016-01-01

    which, in contrast, are all providing short neutron pulses. In order to enable the development of methods and technology adapted to this novel type of source well in advance of the first instruments being constructed at ESS, a test beamline (TBL) was designed and built at the BER II research reactor...... wavelength band between 1.6 A and 10 A by a dedicated wavelength frame multiplication (WFM) chopper system. WFM is proposed for several ESS instruments to allow for flexible time-of-flight resolution. Hence, ESS will benefit from the TBL which offers unique possibilities for testing methods and components...

  8. Multi-site testing and evaluation of remote sensing instruments for wind energy applications

    DEFF Research Database (Denmark)

    Sanz Rodrigo, J.; Borbon Guillen, F.; Gomez Arranz, P.

    2013-01-01

    A procedure for testing and evaluation of remote sensing instruments that makes use of two test sites in flat and complex terrain is presented. To illustrate the method, a system intercomparison experiment is presented involving one sodar and two lidars (pulsed and continuous-wave). The wind...... field, it is also investigated the influence of the background atmospheric stability by classifying the results with the Richardson number in flat terrain and the Froude number in complex terrain. The result is a thorough field calibration of the instruments for a wide range of terrain-flow conditions...

  9. Dataflow approach to testing Java programs supported with DFC

    Directory of Open Access Journals (Sweden)

    Ilona Bluemke

    2015-06-01

    Full Text Available Code based (“white box” approach to testing can be divided into two main types: control flow coverage and data flow coverage methods. Dataflow testing was introduced for structural programming languages and later adopted for object languages. Among many tools supporting code based testing of object programs, only JaBUTi and DFC (Data Flow Coverage support dataflow testing of Java programs. DFC is a tool implemented at the Institute of Computer Science Warsaw University of Technology as an Eclipse plug-in. The objective of this paper is to present dataflow coverage testing of Java programs supported by DFC. DFC finds all definition-uses pairs in tested unit and provides also the definition-uses graph for methods. After the execution of test information which def-uses pairs were covered is shown. An example of data flow testing of Java program is also presented.

  10. Method of case hardening depth testing by using multifunctional ultrasonic testing instrument

    International Nuclear Information System (INIS)

    Salchak, Y A; Sednev, D A; Ardashkin, I B; Kroening, M

    2015-01-01

    The paper describes usability of ultrasonic case hardening depth control applying standard instrument of ultrasonic inspections. The ultrasonic method of measuring the depth of the hardened layer is proposed. Experimental series within the specified and multifunctional ultrasonic equipment are performed. The obtained results are compared with the results of a referent method of analysis. (paper)

  11. Development of Welding and Instrumentation Technology for Nuclear Fuel Test Rod

    International Nuclear Information System (INIS)

    Joung, Chang Young; Ahn, Sung Ho; Heo, Sung Ho; Hong, Jin Tae; Kim, Ka Hye

    2013-01-01

    It is necessary to develop various types of welding, instrumentation and helium gas filling techniques that can conduct TIG spot welding exactly at a pin-hole of the end-cap on the nuclear fuel rod to fill up helium gas. The welding process is one of the most important among the instrumentation processes of the nuclear fuel test rod. To manufacture the nuclear fuel test rod, a precision welding system needs to be fabricated to develop various welding technologies of the fuel test rod jointing the various sensors and end-caps on a fuel cladding tube, which is charged with fuel pellets and component parts. We therefore designed and fabricated an orbital TIG welding system and a laser welding system. This paper describes not only some experiment results from weld tests for the parts of a nuclear fuel test rod, but also the contents for the instrumentation process of the dummy fuel test rod installed with the C-type T. C. A dummy nuclear fuel test rod was successfully fabricated with the welding and instrumentation technologies acquired with various tests. In the test results, the round welding has shown a good weldability at both the orbital TIG welding system and the fiber laser welding system. The spot welding to fill up helium gas has shown a good welding performance at a welding current of 30A, welding time of 0.4 sec and gap of 1 mm in a helium gas atmosphere. The soundness of the nuclear fuel test rod sealed by a mechanical sealing method was confirmed by helium leak tests and microstructural analyses

  12. Testing concordance of instrumental variable effects in generalized linear models with application to Mendelian randomization

    Science.gov (United States)

    Dai, James Y.; Chan, Kwun Chuen Gary; Hsu, Li

    2014-01-01

    Instrumental variable regression is one way to overcome unmeasured confounding and estimate causal effect in observational studies. Built on structural mean models, there has been considerale work recently developed for consistent estimation of causal relative risk and causal odds ratio. Such models can sometimes suffer from identification issues for weak instruments. This hampered the applicability of Mendelian randomization analysis in genetic epidemiology. When there are multiple genetic variants available as instrumental variables, and causal effect is defined in a generalized linear model in the presence of unmeasured confounders, we propose to test concordance between instrumental variable effects on the intermediate exposure and instrumental variable effects on the disease outcome, as a means to test the causal effect. We show that a class of generalized least squares estimators provide valid and consistent tests of causality. For causal effect of a continuous exposure on a dichotomous outcome in logistic models, the proposed estimators are shown to be asymptotically conservative. When the disease outcome is rare, such estimators are consistent due to the log-linear approximation of the logistic function. Optimality of such estimators relative to the well-known two-stage least squares estimator and the double-logistic structural mean model is further discussed. PMID:24863158

  13. Geotechnical instrumentation requirements for atdepth testing and repository monitoring in tuff

    International Nuclear Information System (INIS)

    Zimmerman, R.M.

    1983-01-01

    This paper outlines geotechnical instrumentation requirements for the possible establishment of a nuclear waste repository in tuff on the Nevada Test Site (NTS). The Nuclear Regulatory Commission (NRC) has specified a continuing program to confirm performance during the operational period of the repository, which could last 50 years. Minimum required geotechnical measurements for confirmation of performance include thermal and thermomechanical responses; changes in stress, strain, and displacements; and pore pressure and groundwater flow characteristics. Conditions expected in tuff are: maximum rock temperatures of less than 250 0 C, stresses less than 100 MPa, strains between + or -0.01 mm/mm, and pore pressures less than 35 KPa in the unsaturated zone where hydraulic head is not the primary contributor. The paper describes instrumentation needed to make the desired measurements. In general, the instrumentation and data system are required to be stable and reliable for tens of years. Designs must consider requirements for temperature stability, temperature expansion compensation, moisture resistance, and long-term durability in mining-type environments. Severe requirements such as these suggest consideration of techniques for in-situ replacement of instrumentation. State-of-the-art instrumentation is briefly described along with a discussion of needs for refinement, replacement/recalibration and instrumentation development

  14. Spectralon BRDF and DHR Measurements in Support of Satellite Instruments Operating Through Shortwave Infrared

    Science.gov (United States)

    Georgiev, Georgi T.; Butler, James J.; Thome, Kurt; Cooksey, Catherine; Ding, Leibo

    2016-01-01

    Satellite instruments operating in the reflective solar wavelength region require accurate and precise determination of the Bidirectional Reflectance Distribution Functions (BRDFs) of the laboratory and flight diffusers used in their pre-flight and on-orbit calibrations. This paper advances that initial work and presents a comparison of spectral Bidirectional Reflectance Distribution Function (BRDF) and Directional Hemispherical Reflectance (DHR) of Spectralon*, a common material for laboratory and onorbit flight diffusers. A new measurement setup for BRDF measurements from 900 nm to 2500 nm located at NASA Goddard Space Flight Center (GSFC) is described. The GSFC setup employs an extended indium gallium arsenide detector, bandpass filters, and a supercontinuum light source. Comparisons of the GSFC BRDF measurements in the ShortWave InfraRed (SWIR) with those made by the NIST Spectral Trifunction Automated Reference Reflectometer (STARR) are presented. The Spectralon sample used in this study was 2 inch diameter, 99% white pressed and sintered Polytetrafluoroethylene (PTFE) target. The NASA/NIST BRDF comparison measurements were made at an incident angle of 0 deg and viewing angle of 45 deg. Additional BRDF data not compared to NIST were measured at additional incident and viewing angle geometries and are not presented here The total combined uncertainty for the measurement of BRDF in the SWIR range made by the GSFC scatterometer is less than 1% (k=1). This study is in support of the calibration of the Joint Polar Satellite System (JPSS) Radiation Budget Instrument (RBI) and Visible Infrared Imaging Radiometer Suite (VIIRS) of and other current and future NASA remote sensing missions operating across the reflected solar wavelength region.

  15. Validation of an Instrument and Testing Protocol for Measuring the Combinatorial Analysis Schema.

    Science.gov (United States)

    Staver, John R.; Harty, Harold

    1979-01-01

    Designs a testing situation to examine the presence of combinatorial analysis, to establish construct validity in the use of an instrument, Combinatorial Analysis Behavior Observation Scheme (CABOS), and to investigate the presence of the schema in young adolescents. (Author/GA)

  16. Development and testing of a cross-culturally valid instrument: food-related life style

    DEFF Research Database (Denmark)

    Brunsø, Karen; Grunert, Klaus G.

    1995-01-01

    -culturaly valid way. To this end we have developed a pool of 202 items, collected data in three countries, and have constructed scales based on cross-culturally stable factor patterns. We have then applie set of scales to a fourth country, in order to further test the cross-cultural validity of the instrument....

  17. Testing the Solar Probe Cup, an Instrument Designed to Touch the Sun

    Science.gov (United States)

    Whittlesey, Phyllis L.; Case, Anthony W.; Kasper, Justin Christophe; Wright, Kenneth H., Jr.; Alterman, Ben; Cirtain, Jonathan W.; Bookbinder, Jay; Korreck, Kelly E.; Stevens, Michael Louis

    2014-01-01

    Solar Probe Plus will be the first, fastest, and closest mission to the sun, providing the first direct sampling of the sub-Alfvenic corona. The Solar Probe Cup (SPC) is a unique re-imagining of the traditional Faraday Cup design and materials for immersion in this high temperature environment. Sending an instrument of this type into a never-seen particle environment requires extensive characterization prior to launch to establish sufficient measurement accuracy and instrument response. To reach this end, a slew of tests for allowing SPC to see ranges of appropriate ions and electrons, as well as a facility that reproduces solar photon spectra and fluxes for this mission. Having already tested the SPC at flight like temperatures with no significant modification of the noise floor, we recently completed a round of particle testing to see if the deviations in Faraday Cup design fundamentally change the operation of the instrument. Results and implications from these tests will be presented, as well as performance comparisons to cousin instruments such as those on the WIND spacecraft.

  18. 14 CFR 91.109 - Flight instruction; Simulated instrument flight and certain flight tests.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Flight instruction; Simulated instrument flight and certain flight tests. 91.109 Section 91.109 Aeronautics and Space FEDERAL AVIATION... throwover control wheel in place of fixed, dual controls of the elevator and ailerons when— (1) The...

  19. Testing Instrumentation Validity for Measuring Teachers' Attitudes toward Manipulative Use in the Elementary Classroom

    Science.gov (United States)

    McIntosh, Gina Valdengo

    2012-01-01

    In this study a survey instrument was developed to test elementary teachers' attitudes towards incorporating manipulatives in their math lessons frequently. Though the benefits of using math manipulatives has been reported, there seems to be a disconnect between the benefits of manipulative use and the number of teachers integrating them in their…

  20. Submicronic Particle Measurement Instrumentation Test Bench Data Acquisition and Control System

    International Nuclear Information System (INIS)

    Alberdi, J.; Barcala, J. M.; Sanz, D.; Gomez, F. J.; Molinero, A.; Navarrete, J. J.

    1999-01-01

    This document describes the SAD-100 system characteristics. The unit makes the instrumentation test bench data acquisition and control, SAD-100 was designed and developed by Electronic and Automation Area (CIEMAT) and Aerosol Technology in Energy Generation Project (CIEMAT). (Author) 2 refs

  1. Atlid, ESA atmospheric lidar: manufacture and test results of instrument units

    Science.gov (United States)

    Pereira do Carmo, J.; Hélière, A.; Chassat, F.; Toulemont, Y.; LeFevre, A.

    2017-09-01

    After the successful closure of the Critical Design Review (CDR), the development of the ESA (European Space Agency) ATmospheric LIDAR (Light Detection and Ranging) is now approaching the completion of the manufacturing and testing of all its units and the start of the full instrument integration and qualification campaign.

  2. Reliability-Testing of Two Analysis Instruments for Decision-Making in Curriculum Conferences.

    Science.gov (United States)

    Mulder, Martin; Brake, Jacqueline te

    1990-01-01

    The design and reliability testing of two instruments--the Macro Argumentation Structure (MARS) and the Coalition forming and Dominance (CODOM)--to assess the deliberation process (argumentation and interaction) during curriculum conferences/decision making are reported. The study was conducted at the Department of Education of the University of…

  3. Building the BIKE: Development and Testing of the Biotechnology Instrument for Knowledge Elicitation (BIKE)

    Science.gov (United States)

    Witzig, Stephen B.; Rebello, Carina M.; Siegel, Marcelle A.; Freyermuth, Sharyn K.; Izci, Kemal; McClure, Bruce

    2014-10-01

    Identifying students' conceptual scientific understanding is difficult if the appropriate tools are not available for educators. Concept inventories have become a popular tool to assess student understanding; however, traditionally, they are multiple choice tests. International science education standard documents advocate that assessments should be reform based, contain diverse question types, and should align with instructional approaches. To date, no instrument of this type targeting student conceptions in biotechnology has been developed. We report here the development, testing, and validation of a 35-item Biotechnology Instrument for Knowledge Elicitation (BIKE) that includes a mix of question types. The BIKE was designed to elicit student thinking and a variety of conceptual understandings, as opposed to testing closed-ended responses. The design phase contained nine steps including a literature search for content, student interviews, a pilot test, as well as expert review. Data from 175 students over two semesters, including 16 student interviews and six expert reviewers (professors from six different institutions), were used to validate the instrument. Cronbach's alpha on the pre/posttest was 0.664 and 0.668, respectively, indicating the BIKE has internal consistency. Cohen's kappa for inter-rater reliability among the 6,525 total items was 0.684 indicating substantial agreement among scorers. Item analysis demonstrated that the items were challenging, there was discrimination among the individual items, and there was alignment with research-based design principles for construct validity. This study provides a reliable and valid conceptual understanding instrument in the understudied area of biotechnology.

  4. Design and implementation of ATCA-based 100Gbps DP-QPSK optical signal test instrument

    Science.gov (United States)

    Su, Shaojing; Qin, Jiangyi; Huang, Zhiping; Liu, Chenwu

    2014-11-01

    In order to achieve the receiving task of 100Gbps Dual Polarization-Quadrature Phase Shift Keying (DP-QPSK) optical signal acquisition instrument, improve acquisition performance of the instrument, this paper has deeply researched DP-QPSK modulation principles, demodulation techniques and the key technologies of optical signal acquisition. The theories of DP-QPSK optical signal transmission are researched. The DP-QPSK optical signal transmission model is deduced. And the clock and data recovery in high-speed data acquisition and offset correction of multi-channel data are researched. By reasonable hardware circuit design and software system construction, the utilization of high performance Advanced Telecom Computing Architecture (ATCA), this paper proposes a 100Gbps DP-QPSK optical signal acquisition instrument which is based on ATCA. The implementations of key modules are presented by comparison and argumentation. According to the modularization idea, the instrument can be divided into eight modules. Each module performs the following functions. (1) DP-QPSK coherent detection demodulation module; (2) deceleration module; (3) FPGA (Field Programmable Gate Array); (4) storage module; (5) data transmission module; (6) clock module; (7) power module; (8) JTAG debugging, configuration module; What is more, this paper has put forward two solutions to test optical signal acquisition instrument performance. The first scenario is based on a standard STM-256 optical signal format and exploits the SignalTap of QuartusII software to monitor the optical signal data. Another scenario is to use a pseudo-random signal series to generate data, acquisition module acquires a certain amount of data signals, and then the signals are transferred to a computer by the Gigabit Ethernet to analyze. Two testing results show that the bit error rate of optical signal acquisition instrument is low. And the instrument fully meets the requirements of signal receiving system. At the same time

  5. Development and psychometric testing of an instrument to measure safety climate perceptions in community pharmacy.

    Science.gov (United States)

    Newham, Rosemary; Bennie, Marion; Maxwell, David; Watson, Anne; de Wet, Carl; Bowie, Paul

    2014-12-01

    A positive and strong safety culture underpins effective learning from patient safety incidents in health care, including the community pharmacy (CP) setting. To build this culture, perceptions of safety climate must be measured with context-specific and reliable instruments. No pre-existing instruments were specifically designed or suitable for CP within Scotland. We therefore aimed to develop a psychometrically sound instrument to measure perceptions of safety climate within Scottish CPs. The first stage, development of a preliminary instrument, comprised three steps: (i) a literature review; (ii) focus group feedback; and (iii) content validation. The second stage, psychometric testing, consisted of three further steps: (iv) a pilot survey; (v) a survey of all CP staff within a single health board in NHS Scotland; and (vi) application of statistical methods, including principal components analysis and calculation of Cronbach's reliability coefficients, to derive the final instrument. The preliminary questionnaire was developed through a process of literature review and feedback. This questionnaire was completed by staff in 50 CPs from the 131 (38%) sampled. 250 completed questionnaires were suitable for analysis. Psychometric evaluation resulted in a 30-item instrument with five positively correlated safety climate factors: leadership, teamwork, safety systems, communication and working conditions. Reliability coefficients were satisfactory for the safety climate factors (α > 0.7) and overall (α = 0.93). The robust nature of the technical design and testing process has resulted in the development of an instrument with sufficient psychometric properties, which can be implemented in the community pharmacy setting in NHS Scotland. © 2014 John Wiley & Sons, Ltd.

  6. The test beamline of the European Spallation Source – Instrumentation development and wavelength frame multiplication

    International Nuclear Information System (INIS)

    Woracek, R.; Hofmann, T.; Bulat, M.; Sales, M.; Habicht, K.; Andersen, K.; Strobl, M.

    2016-01-01

    The European Spallation Source (ESS), scheduled to start operation in 2020, is aiming to deliver the most intense neutron beams for experimental research of any facility worldwide. Its long pulse time structure implies significant differences for instrumentation compared to other spallation sources which, in contrast, are all providing short neutron pulses. In order to enable the development of methods and technology adapted to this novel type of source well in advance of the first instruments being constructed at ESS, a test beamline (TBL) was designed and built at the BER II research reactor at Helmholtz-Zentrum Berlin (HZB). Operating the TBL shall provide valuable experience in order to allow for a smooth start of operations at ESS. The beamline is capable of mimicking the ESS pulse structure by a double chopper system and provides variable wavelength resolution as low as 0.5% over a wide wavelength band between 1.6 Å and 10 Å by a dedicated wavelength frame multiplication (WFM) chopper system. WFM is proposed for several ESS instruments to allow for flexible time-of-flight resolution. Hence, ESS will benefit from the TBL which offers unique possibilities for testing methods and components. This article describes the main capabilities of the instrument, its performance as experimentally verified during the commissioning, and its relevance to currently starting ESS instrumentation projects.

  7. The ChemCam Instrument Suite on the Mars Science Laboratory (MSL) Rover: Body Unit and Combined System Tests

    International Nuclear Information System (INIS)

    Wiens, Roger C.; Barraclough, Bruce; Barkley, Walter C.; Bender, Steve; Bernardin, John; Bultman, Nathan; Clanton, Robert C.; Clegg, Samuel; Delapp, Dorothea; Dingler, Robert; Enemark, Don; Flores, Mike; Hale, Thomas; Lanza, Nina; Lasue, Jeremie; Latino, Joseph; Little, Cynthia; Morrison, Leland; Nelson, Tony; Romero, Frank; Salazar, Steven; Stiglich, Ralph; Storms, Steven; Trujillo, Tanner; Ulibarri, Mike; Vaniman, David; Whitaker, Robert; Witt, James; Maurice, Sylvestre; Bouye, Marc; Cousin, Agnes; Cros, Alain; D'Uston, Claude; Forni, Olivier; Gasnault, Olivier; Kouach, Driss; Lasue, Jeremie; Pares, Laurent; Poitrasson, Franck; Striebig, Nicolas; Thocaven, Jean-Jacques; Saccoccio, Muriel; Perez, Rene; Bell, James F. III; Hays, Charles; Blaney, Diana; DeFlores, Lauren; Elliott, Tom; Kan, Ed; Limonadi, Daniel; Lindensmith, Chris; Miller, Ed; Reiter, Joseph W.; Roberts, Tom; Simmonds, John J.; Warner, Noah; Blank, Jennifer; Bridges, Nathan; Cais, Phillippe; Clark, Benton; Cremers, David; Dyar, M. Darby; Fabre, Cecile; Herkenhoff, Ken; Kirkland, Laurel; Landis, David; Langevin, Yves; Lanza, Nina; Newsom, Horton; Ollila, Ann; LaRocca, Frank; Ott, Melanie; Mangold, Nicolas; Manhes, Gerard; Mauchien, Patrick; Blank, Jennifer; McKay, Christopher; Mooney, Joe; Provost, Cheryl; Morris, Richard V.; Sautter, Violaine; Sautter, Violaine; Waterbury, Rob; Wong-Swanson, Belinda; Barraclough, Bruce; Bender, Steve; Vaniman, David

    2012-01-01

    The ChemCam instrument suite on the Mars Science Laboratory (MSL) rover Curiosity provides remote compositional information using the first laser-induced breakdown spectrometer (LIBS) on a planetary mission, and provides sample texture and morphology data using a remote micro-imager (RMI). Overall, ChemCam supports MSL with five capabilities: remote classification of rock and soil characteristics; quantitative elemental compositions including light elements like hydrogen and some elements to which LIBS is uniquely sensitive (e.g., Li, Be, Rb, Sr, Ba); remote removal of surface dust and depth profiling through surface coatings; context imaging; and passive spectroscopy over the 240-905 nm range. ChemCam is built in two sections: The mast unit, consisting of a laser, telescope, RMI, and associated electronics, resides on the rover's mast, and is described in a companion paper. ChemCam's body unit, which is mounted in the body of the rover, comprises an optical de-multiplexer, three spectrometers, detectors, their coolers, and associated electronics and data handling logic. Additional instrument components include a 6 m optical fiber which transfers the LIBS light from the telescope to the body unit, and a set of onboard calibration targets. ChemCam was integrated and tested at Los Alamos National Laboratory where it also underwent LIBS calibration with 69 geological standards prior to integration with the rover. Post-integration testing used coordinated mast and instrument commands, including LIBS line scans on rock targets during system-level thermal-vacuum tests. In this paper we describe the body unit, optical fiber, and calibration targets, and the assembly, testing, and verification of the instrument prior to launch. (authors)

  8. Evaluation of hydrogen embrittlement and temper embrittlement by key curve method in instrumented Charpy test

    OpenAIRE

    Makita A.; Shindo Y.; Ohtsuka N.

    2010-01-01

    Instrumented Charpy test was conducted on small sized specimen of 21/4Cr-1Mo steel. In the test the single specimen key curve method was applied to determine the value of fracture toughness for the initiation of crack extension with hydrogen free, KIC, and for hydrogen embrittlement cracking, KIH. Also the tearing modulus as a parameter for resistance to crack extension was determined. The role of these parameters was discussed at an upper shelf temperature and at a transition temperat...

  9. Thermal and Alignment Analysis of the Instrument-Level ATLAS Thermal Vacuum Test

    Science.gov (United States)

    Bradshaw, Heather

    2012-01-01

    This paper describes the thermal analysis and test design performed in preparation for the ATLAS thermal vacuum test. NASA's Advanced Topographic Laser Altimeter System (ATLAS) will be flown as the sole instrument aboard the Ice, Cloud, and land Elevation Satellite-2 (ICESat-2). It will be used to take measurements of topography and ice thickness for Arctic and Antarctic regions, providing crucial data used to predict future changes in worldwide sea levels. Due to the precise measurements ATLAS is taking, the laser altimeter has very tight pointing requirements. Therefore, the instrument is very sensitive to temperature-induced thermal distortions. For this reason, it is necessary to perform a Structural, Thermal, Optical Performance (STOP) analysis not only for flight, but also to ensure performance requirements can be operationally met during instrument-level thermal vacuum testing. This paper describes the thermal model created for the chamber setup, which was used to generate inputs for the environmental STOP analysis. This paper also presents the results of the STOP analysis, which indicate that the test predictions adequately replicate the thermal distortions predicted for flight. This is a new application of an existing process, as STOP analyses are generally performed to predict flight behavior only. Another novel aspect of this test is that it presents the opportunity to verify pointing results of a STOP model, which is not generally done. It is possible in this case, however, because the actual pointing will be measured using flight hardware during thermal vacuum testing and can be compared to STOP predictions.

  10. Results of the first tests of the SIDRA satellite-borne instrument breadboard model

    International Nuclear Information System (INIS)

    Dudnik, O.V.; Kurbatov, E.V.; Avilov, A.M.; Titov, K.G.; Prieto, M; Sanchez, S.; Spassky, A.V.; Sylwester, J.; Gburek, S.; Podgorski, P.

    2013-01-01

    In this work, the results of the calibration of the solid-state detectors and electronic channels of the SIDRA satellite borne energetic charged particle spectrometer-telescope breadboard model are presented. The block schemes and experimental equipment used to conduct the thermal vacuum and electromagnetic compatibility tests of the assemblies and modules of the compact satellite equipment are described. The results of the measured thermal conditions of operation of the signal analog and digital processing critical modules of the SIDRA instrument prototype are discussed. Finally, the levels of conducted interference generated by the instrument model in the primary vehicle-borne power circuits are presented.

  11. Development and testing of a cross-culturally valid instrument: food-related life style

    DEFF Research Database (Denmark)

    Brunsø, Karen; Grunert, Klaus G.

    1995-01-01

    Based on a cognitive perspective, we propose to make life style specific to certain areas of consumption. The specific area of consumption studied here is food, resulting in a concept of food-related life style. We have developed an instrument tha measure food-related life style in a cross......-culturaly valid way. To this end we have developed a pool of 202 items, collected data in three countries, and have constructed scales based on cross-culturally stable factor patterns. We have then applie set of scales to a fourth country, in order to further test the cross-cultural validity of the instrument....

  12. A comparison of two reciprocating instruments using bending stress and cyclic fatigue tests

    OpenAIRE

    SCELZA, Pantaleo; Harry, DAVIDOWICZ; SILVA, Licinio Esmeraldo da; BARBOSA, Igor Bastos; SCELZA, Miriam Zaccaro

    2015-01-01

    The aim of this study was to comparatively evaluate the bending resistance at 45º, the static and dynamic cyclic fatigue life, and the fracture type of the WaveOne (Dentsply Maillefer, Ballaigues, Switzerland) 25-08 and Reciproc (VDW, Munich, Germany) 25-08 instruments. A total of 60 nickel-titanium (NiTi) instruments (30 Reciproc and 30 WaveOne) from three different lots, each of which was 25 mm in length, were tested. The bending resistance was evaluated through the results of a cantilever-...

  13. Proposal for a Universal Test Mirror for Characterization of Slope Measuring Instruments

    International Nuclear Information System (INIS)

    Yashchuk, Valeriy V.; McKinney, Wayne R.; Warwick, Tony; Noll, Tino; Siewert, Frank; Zeschke, Thomas; Geckeler, Ralf D.

    2007-01-01

    The development of third generation light sources like the Advanced Light Source (ALS) or BESSY II brought to a focus the need for high performance synchrotron optics with unprecedented tolerances for slope error and micro roughness. Proposed beam lines at Free Electron Lasers (FEL) require optical elements up to a length of one meter, characterized by a residual slope error in the range of 0.1mu rad (rms),and rms values of 0.1 nm for micro roughness. These optical elements must be inspected by highly accurate measuring instruments, providing a measurement uncertainty lower than the specified accuracy of the surface under test. It is essential that metrology devices in use at synchrotron laboratories be precisely characterized and calibrated to achieve this target. In this paper we discuss a proposal for a Universal Test Mirror (UTM) as a realization of a high performance calibration instrument. The instrument would provide an ideal calibration surface to replicate a redundant surface under test of redundant figure. The application of a sophisticated calibration instrument will allow the elimination of the majority of the systematic error from the error budget of an individual measurement of a particular optical element. We present the limitations of existing methods, initial UTM design considerations, possible calibration algorithms, and an estimation of the expected accuracy

  14. Propulsion Test Support Analysis with GPU Computing, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — The design, development and staging of tests to certify liquid rocket engines usually require high-fidelity structural, fluid and thermal support analysis. These...

  15. AHMCT Intelligent Roadway Information System (IRIS) technical support and testing.

    Science.gov (United States)

    2011-12-01

    This report documents the research project AHMCT IRIS Technical Support and Testing, : performed under contract 65A0275, Task ID 1777. It presents an overview of the Intelligent : Roadway Information System (IRIS), and its design and function. ...

  16. Software Testing During Post-Deployment Support of Weapon Systems

    National Research Council Canada - National Science Library

    Gimble, Thomas

    1994-01-01

    We are providing this final audit report for your information and use. The report discusses policies, procedures, and methodologies for software testing during post-deployment support of weapon systems...

  17. AHMCT Intelligent Roadway Information System (IRIS) technical support and testing

    Science.gov (United States)

    2011-12-31

    This report documents the research project AHMCT IRIS Technical Support and Testing, : performed under contract 65A0275, Task ID 1777. It presents an overview of the Intelligent : Roadway Information System (IRIS), and its design and function. ...

  18. The development and psychometric testing of a theory-based instrument to evaluate nurses' perception of clinical reasoning competence.

    Science.gov (United States)

    Liou, Shwu-Ru; Liu, Hsiu-Chen; Tsai, Hsiu-Min; Tsai, Ying-Huang; Lin, Yu-Ching; Chang, Chia-Hao; Cheng, Ching-Yu

    2016-03-01

    The purpose of the study was to develop and psychometrically test the Nurses Clinical Reasoning Scale. Clinical reasoning is an essential skill for providing safe and quality patient care. Identifying pre-graduates' and nurses' needs and designing training courses to improve their clinical reasoning competence becomes a critical task. However, there is no instrument focusing on clinical reasoning in the nursing profession. Cross-sectional design was used. This study included the development of the scale, a pilot study that preliminary tested the readability and reliability of the developed scale and a main study that implemented and tested the psychometric properties of the developed scale. The Nurses Clinical Reasoning Scale was developed based on the Clinical Reasoning Model. The scale includes 15 items using a Likert five-point scale. Data were collected from 2013-2014. Two hundred and fifty-one participants comprising clinical nurses and nursing pre-graduates completed and returned the questionnaires in the main study. The instrument was tested for internal consistency and test-retest reliability. Its validity was tested with content, construct and known-groups validity. One factor emerged from the factor analysis. The known-groups validity was confirmed. The Cronbach's alpha for the entire instrument was 0·9. The reliability and validity of the Nurses Clinical Reasoning Scale were supported. The scale is a useful tool and can be easily administered for the self-assessment of clinical reasoning competence of clinical nurses and future baccalaureate nursing graduates. Study limitations and further recommendations are discussed. © 2015 John Wiley & Sons Ltd.

  19. A weak instrument [Formula: see text]-test in linear IV models with multiple endogenous variables.

    Science.gov (United States)

    Sanderson, Eleanor; Windmeijer, Frank

    2016-02-01

    We consider testing for weak instruments in a model with multiple endogenous variables. Unlike Stock and Yogo (2005), who considered a weak instruments problem where the rank of the matrix of reduced form parameters is near zero, here we consider a weak instruments problem of a near rank reduction of one in the matrix of reduced form parameters. For example, in a two-variable model, we consider weak instrument asymptotics of the form [Formula: see text] where [Formula: see text] and [Formula: see text] are the parameters in the two reduced-form equations, [Formula: see text] is a vector of constants and [Formula: see text] is the sample size. We investigate the use of a conditional first-stage [Formula: see text]-statistic along the lines of the proposal by Angrist and Pischke (2009) and show that, unless [Formula: see text], the variance in the denominator of their [Formula: see text]-statistic needs to be adjusted in order to get a correct asymptotic distribution when testing the hypothesis [Formula: see text]. We show that a corrected conditional [Formula: see text]-statistic is equivalent to the Cragg and Donald (1993) minimum eigenvalue rank test statistic, and is informative about the maximum total relative bias of the 2SLS estimator and the Wald tests size distortions. When [Formula: see text] in the two-variable model, or when there are more than two endogenous variables, further information over and above the Cragg-Donald statistic can be obtained about the nature of the weak instrument problem by computing the conditional first-stage [Formula: see text]-statistics.

  20. Inter-instrumental method transfer of chiral capillary electrophoretic methods using robustness test information.

    Science.gov (United States)

    De Cock, Bart; Borsuk, Agnieszka; Dejaegher, Bieke; Stiens, Johan; Mangelings, Debby; Vander Heyden, Yvan

    2014-08-01

    Capillary electrophoresis (CE) is an electrodriven separation technique that is often used for the separation of chiral molecules. Advantages of CE are its flexibility, low cost and efficiency. On the other hand, the precision and transfer of CE methods are well-known problems of the technique. Reasons for the more complicated method transfer are the more diverse instrumental differences, such as total capillary lengths and capillary cooling systems; and the higher response variability of CE methods compared to other techniques, such as liquid chromatography (HPLC). Therefore, a larger systematic change in peak resolutions, migration times and peak areas, with a loss of separation and efficiency may be seen when a CE method is transferred to another laboratory or another type of instrument. A swift and successful method transfer is required because development and routine use of analytical methods are usually not performed in the same laboratory and/or on the same type of equipment. The aim of our study was to develop transfer rules to facilitate CE method transfers between different laboratories and instruments. In our case study, three β-blockers were chirally separated and inter-instrumental transfers were performed. The first step of our study was to optimise the precision of the chiral CE method. Next, a robustness test was performed to identify the instrumental and experimental parameters that were most influencing the considered responses. The precision- and the robustness study results were used to adapt instrumental and/or method settings to improve the transfer between different instruments. Finally, the comparison of adapted and non-adapted transfers allowed deriving some rules to facilitate CE method transfers. Copyright © 2014 Elsevier B.V. All rights reserved.

  1. Development and design of a late-model fitness test instrument based on LabView

    Science.gov (United States)

    Xie, Ying; Wu, Feiqing

    2010-12-01

    Undergraduates are pioneers of China's modernization program and undertake the historic mission of rejuvenating our nation in the 21st century, whose physical fitness is vital. A smart fitness test system can well help them understand their fitness and health conditions, thus they can choose more suitable approaches and make practical plans for exercising according to their own situation. following the future trends, a Late-model fitness test Instrument based on LabView has been designed to remedy defects of today's instruments. The system hardware consists of fives types of sensors with their peripheral circuits, an acquisition card of NI USB-6251 and a computer, while the system software, on the basis of LabView, includes modules of user register, data acquisition, data process and display, and data storage. The system, featured by modularization and an open structure, is able to be revised according to actual needs. Tests results have verified the system's stability and reliability.

  2. Computer aided instrumented Charpy test applied dynamic fracture toughness evaluation system

    International Nuclear Information System (INIS)

    Kobayashi, Toshiro; Niinomi, Mitsuo

    1986-01-01

    Micro computer aided data treatment system and personal computer aided data analysis system were applied to the traditional instrumented Charpy impact test system. The analysis of Charpy absorbed energy (E i , E p , E t ) and load (P y , P m ), and the evaluation of dynamic toughness through whole fracture process, i.e. J Id , J R curve and T mat was examined using newly developed computer aided instrumented Charpy impact test system. E i , E p , E t , P y and P m were effectively analyzed using moving average method and printed out automatically by micro computer aided data treatment system. J Id , J R curve and T mat could be measured by stop block test method. Then, J Id , J R curve and T mat were effectively estimated using compliance changing rate method and key curve method on the load-load point displacement curve of single fatigue cracked specimen by personal computer aided data analysis system. (author)

  3. Virtual instrumention-based linearity test platform for DCCT of digital power supply at SSRF

    International Nuclear Information System (INIS)

    Tang Junlong; Li Deming; Shen Tianjian; Liu Hong

    2008-01-01

    Based on virtual instrumentation, a reliable and effective test platform, performing instrument control, data acquisition and data recording, has been established to evaluate linearity of high performance DCCT (DC current transducer) for digital power supply at Shanghai Synchrotron Radiation Facility (SSRF). The software in LabVIEW language was developed to perform computer communication via serial communication (RS232) and GPIB, providing a friendly user interface to the linearity test platform. This makes it easy to test the linearity and control power on or off and current output of high-precision and high-current DC constant current output power supply. The experimental data, stored in an EXCEL file, can be processed to obtain DCCT linearity, and provide basis to further analyze DCCT performance in the future. (authors)

  4. Vertebral Osteomyelitis Caused by Mycobacterium abscessus Surgically Treated Using Antibacterial Iodine-Supported Instrumentation

    Directory of Open Access Journals (Sweden)

    Satoshi Kato

    2014-01-01

    Full Text Available Mycobacterium abscessus infections rarely develop in healthy individuals, and mostly they occur in immunocompromised hosts. Vertebral osteomyelitis due to Mycobacterium abscessus is very rare and only three previous cases of spinal infection caused by Mycobacterium abscessus have been reported. Mycobacterium abscessus isolates are uniformly resistant to antituberculous agents and can display a virulent biofilm-forming phenotype. The patient was a 67-year-old woman with vertebral osteomyelitis of the L1-2. She was healthy without immune-suppressed condition, history of trauma, or intravenous drug use. The smear examination of the specimen harvested by CT-guided puncture of the paravertebral abscess revealed Mycobacterium abscessus. Her disease condition did not abate with conservative treatment using antimicrobial chemotherapy. Radical debridement of the vertebral osteomyelitis and anterior reconstruction from T12 to L2 using antibacterial iodine-supported instrumentation were performed. Chemotherapy using clarithromycin, amikacin, and imipenem was applied for 6 months after surgery as these antibiotics had been proven to be effective to Mycobacterium abscessus after surgery. Two years after surgery, the infected anterior site healed and bony fusion was successfully achieved without a recurrence of infection.

  5. Human-Robot Collaboration Dynamic Impact Testing and Calibration Instrument for Disposable Robot Safety Artifacts.

    Science.gov (United States)

    Dagalakis, Nicholas G; Yoo, Jae Myung; Oeste, Thomas

    2016-01-01

    The Dynamic Impact Testing and Calibration Instrument (DITCI) is a simple instrument with a significant data collection and analysis capability that is used for the testing and calibration of biosimulant human tissue artifacts. These artifacts may be used to measure the severity of injuries caused in the case of a robot impact with a human. In this paper we describe the DITCI adjustable impact and flexible foundation mechanism, which allows the selection of a variety of impact force levels and foundation stiffness. The instrument can accommodate arrays of a variety of sensors and impact tools, simulating both real manufacturing tools and the testing requirements of standards setting organizations. A computer data acquisition system may collect a variety of impact motion, force, and torque data, which are used to develop a variety of mathematical model representations of the artifacts. Finally, we describe the fabrication and testing of human abdomen soft tissue artifacts, used to display the magnitude of impact tissue deformation. Impact tests were performed at various maximum impact force and average pressure levels.

  6. Report on monitoring and support instruments for solar physics research from Spacelab

    Science.gov (United States)

    1978-01-01

    The Quick Reaction and Special Purpose Facility Definition Team for Solar Physics Spacelab Payloads examined a variety of instruments to fulfill the following functions: (1) solar physics research appropriate to Spacelab, (2) correlative data for research in such fields as aeronomy, magnetospheric physics, ionospheric physics, meteorology and climatology, (3) target selection for activity alert monitoring and (4) pointing accuracy monitoring of Spacelab platforms. In this examination the team accepted a number of restrictions and qualifications: (1) the cost of such instruments must be low, so as not to adversely impact the development of new, research class instrumentation in the early Spacelab era; (2) the instruments should be of such a size that they each would occupy a small fraction of a pointing system, and (3) the weight and power consumption of the instruments should also be small. With these restrictions, the instruments chosen are: the visible light telescope and magnetograph, the extreme-ultraviolet telescope, and the solar irradiance monitor.

  7. Using cognitive pre-testing methods in the development of a new evidenced-based pressure ulcer risk assessment instrument.

    Science.gov (United States)

    Coleman, S; Nixon, J; Keen, J; Muir, D; Wilson, L; McGinnis, E; Stubbs, N; Dealey, C; Nelson, E A

    2016-11-16

    Variation in development methods of Pressure Ulcer Risk Assessment Instruments has led to inconsistent inclusion of risk factors and concerns about content validity. A new evidenced-based Risk Assessment Instrument, the Pressure Ulcer Risk Primary Or Secondary Evaluation Tool - PURPOSE-T was developed as part of a National Institute for Health Research (NIHR) funded Pressure Ulcer Research Programme (PURPOSE: RP-PG-0407-10056). This paper reports the pre-test phase to assess and improve PURPOSE-T acceptability, usability and confirm content validity. A descriptive study incorporating cognitive pre-testing methods and integration of service user views was undertaken over 3 cycles comprising PURPOSE-T training, a focus group and one-to-one think-aloud interviews. Clinical nurses from 2 acute and 2 community NHS Trusts, were grouped according to job role. Focus group participants used 3 vignettes to complete PURPOSE-T assessments and then participated in the focus group. Think-aloud participants were interviewed during their completion of PURPOSE-T. After each pre-test cycle analysis was undertaken and adjustment/improvements made to PURPOSE-T in an iterative process. This incorporated the use of descriptive statistics for data completeness and decision rule compliance and directed content analysis for interview and focus group data. Data were collected April 2012-June 2012. Thirty-four nurses participated in 3 pre-test cycles. Data from 3 focus groups, 12 think-aloud interviews incorporating 101 PURPOSE-T assessments led to changes to improve instrument content and design, flow and format, decision support and item-specific wording. Acceptability and usability were demonstrated by improved data completion and appropriate risk pathway allocation. The pre-test also confirmed content validity with clinical nurses. The pre-test was an important step in the development of the preliminary PURPOSE-T and the methods used may have wider instrument development application

  8. Using cognitive pre-testing methods in the development of a new evidenced-based pressure ulcer risk assessment instrument

    Directory of Open Access Journals (Sweden)

    S. Coleman

    2016-11-01

    Full Text Available Abstract Background Variation in development methods of Pressure Ulcer Risk Assessment Instruments has led to inconsistent inclusion of risk factors and concerns about content validity. A new evidenced-based Risk Assessment Instrument, the Pressure Ulcer Risk Primary Or Secondary Evaluation Tool - PURPOSE-T was developed as part of a National Institute for Health Research (NIHR funded Pressure Ulcer Research Programme (PURPOSE: RP-PG-0407-10056. This paper reports the pre-test phase to assess and improve PURPOSE-T acceptability, usability and confirm content validity. Methods A descriptive study incorporating cognitive pre-testing methods and integration of service user views was undertaken over 3 cycles comprising PURPOSE-T training, a focus group and one-to-one think-aloud interviews. Clinical nurses from 2 acute and 2 community NHS Trusts, were grouped according to job role. Focus group participants used 3 vignettes to complete PURPOSE-T assessments and then participated in the focus group. Think-aloud participants were interviewed during their completion of PURPOSE-T. After each pre-test cycle analysis was undertaken and adjustment/improvements made to PURPOSE-T in an iterative process. This incorporated the use of descriptive statistics for data completeness and decision rule compliance and directed content analysis for interview and focus group data. Data were collected April 2012-June 2012. Results Thirty-four nurses participated in 3 pre-test cycles. Data from 3 focus groups, 12 think-aloud interviews incorporating 101 PURPOSE-T assessments led to changes to improve instrument content and design, flow and format, decision support and item-specific wording. Acceptability and usability were demonstrated by improved data completion and appropriate risk pathway allocation. The pre-test also confirmed content validity with clinical nurses. Conclusions The pre-test was an important step in the development of the preliminary PURPOSE-T and the

  9. BUSTED BUTTE TEST FACILITY GROUND SUPPORT CONFIRMATION ANALYSIS

    International Nuclear Information System (INIS)

    Bonabian, S.

    1998-01-01

    The main purpose and objective of this analysis is to confirm the validity of the ground support design for Busted Butte Test Facility (BBTF). The highwall stability and adequacy of highwall and tunnel ground support is addressed in this analysis. The design of the BBTF including the ground support system was performed in a separate document (Reference 5.3). Both in situ and seismic loads are considered in the evaluation of the highwall and the tunnel ground support system. In this analysis only the ground support designed in Reference 5.3 is addressed. The additional ground support installed (still work in progress) by the constructor is not addressed in this analysis. This additional ground support was evaluated by the A/E during a site visit and its findings and recommendations are addressed in this analysis

  10. Standard practice for evaluating performance characteristics of ultrasonic Pulse-Echo testing instruments and systems without the use of electronic measurement instruments

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2011-01-01

    1.1 This practice describes procedures for evaluating the following performance characteristics of ultrasonic pulse-echo examination instruments and systems: Horizontal Limit and Linearity; Vertical Limit and Linearity; Resolution - Entry Surface and Far Surface; Sensitivity and Noise; Accuracy of Calibrated Gain Controls. Evaluation of these characteristics is intended to be used for comparing instruments and systems or, by periodic repetition, for detecting long-term changes in the characteristics of a given instrument or system that may be indicative of impending failure, and which, if beyond certain limits, will require corrective maintenance. Instrument characteristics measured in accordance with this practice are expressed in terms that relate to their potential usefulness for ultrasonic testing. Instrument characteristics expressed in purely electronic terms may be measured as described in E1324. 1.2 Ultrasonic examination systems using pulsed-wave trains and A-scan presentation (rf or video) may be ev...

  11. Optical Testing and Verification Methods for the James Webb Space Telescope Integrated Science Instrument Module Element

    Science.gov (United States)

    Antonille, Scott R.; Miskey, Cherie L.; Ohl, Raymond G.; Rohrbach, Scott O.; Aronstein, David L.; Bartoszyk, Andrew E.; Bowers, Charles W.; Cofie, Emmanuel; Collins, Nicholas R.; Comber, Brian J.; hide

    2016-01-01

    NASA's James Webb Space Telescope (JWST) is a 6.6m diameter, segmented, deployable telescope for cryogenic IR space astronomy (40K). The JWST Observatory includes the Optical Telescope Element (OTE) and the Integrated Science Instrument Module (ISIM) that contains four science instruments (SI) and the fine guider. The SIs are mounted to a composite metering structure. The SI and guider units were integrated to the ISIM structure and optically tested at the NASA Goddard Space Flight Center as a suite using the Optical Telescope Element SIMulator (OSIM). OSIM is a full field, cryogenic JWST telescope simulator. SI performance, including alignment and wave front error, were evaluated using OSIM. We describe test and analysis methods for optical performance verification of the ISIM Element, with an emphasis on the processes used to plan and execute the test. The complexity of ISIM and OSIM drove us to develop a software tool for test planning that allows for configuration control of observations, associated scripts, and management of hardware and software limits and constraints, as well as tools for rapid data evaluation, and flexible re-planning in response to the unexpected. As examples of our test and analysis approach, we discuss how factors such as the ground test thermal environment are compensated in alignment. We describe how these innovative methods for test planning and execution and post-test analysis were instrumental in the verification program for the ISIM element, with enough information to allow the reader to consider these innovations and lessons learned in this successful effort in their future testing for other programs.

  12. Development of an Autonomous Lidar Instrument for Use on a UAV Platform in Support of Homeland Security

    Science.gov (United States)

    McGill, Matthew; Famiglietti, Joe

    2005-01-01

    Researchers at NASA's Goddard Space Flight Center have developed an autonomous aerosol backscatter lidar instrument for use on the high-altitude ER-2 aircraft (for more information please visit http://cpl.gsfc.nasa.gov). Work is currently underway to transfer this instrument to a UAV platform such as Global Hawk. While the NASA applications are Earth science and satellite validation, there is clearly a Homeland Security application for such an instrument. One novel concept is to have a fleet of UAVs stationed around the country, each UAV having a payload including a lidar instrument. In the event of attack, the appropriate UAV(s) could be launched for purposes of, e.g., plume detection and tracking that are critical for decision support. While the existing lidar instrument is not directly capable of biological species discrimination, it is capable of plume tracking and thus can demonstrate to DHS the capabilities and utility of such instruments. Using NASA funding we will have an instrument ready to fly on Global Hawk by end of 2005. We would like to find partners, either within private industry or within DHS who would be willing to contribute aircraft access and flight hours for a demonstration flight. Longer-term partnerships to develop more advanced and more capable types of lidar instruments are also desirable. In this presentation we will detail the existing ER-2 lidar instrument and show measurement results, show the progress made on adapting to the Global Hawk platform, present concepts for DHS uses of such instruments, and openly pursue partnership opportunities.

  13. The Household Risk Perception instrument and the Self-Efficacy in Environmental Risk Reduction instrument: psychometric testing using principal component analysis.

    Science.gov (United States)

    Oneal, Gail; Odom-Maryon, Tamara; Postma, Julie; Hill, Wade; Butterfield, Patricia

    2013-09-01

    To report the psychometric testing of the Household Risk Perception and Self-Efficacy in Environmental Risk Reduction instruments using principal components analysis. There are limited instruments available to test household risk perception and self-efficacy related to environmental health behaviours. The Household Risk Perception instrument was developed to measure personal perceptions of household environmental health risks. The Self-Efficacy in Environmental Risk Reduction instrument was designed to measure caregivers' confidence in taking steps to reduce household risks. An exploratory analysis of previous data was undertaken. Baseline data from 235 caregivers enrolled in a randomized clinical trial testing a healthy housing intervention were collected between 2006-2009. Principal components analysis was used to determine principal components from measured responses to each instrument. Components were explored and compared to constructs used to design the original instruments. A five-component structure showed the simplest solution and explained 65% of variance in the Household Risk Perception analysis. Cronbach's alpha values indicated satisfactory internal consistency for four of five identified components. Risk perception varied according to available sensory input of the specific risk. A four-component structure explained 64% of the variance in the Self-Efficacy in Environmental Risk Reduction analysis. Cronbach's alpha values were satisfactory. Items mapped to steps in an action-oriented process vs. agent-specific actions. Results from both analyses suggest that environmental tobacco smoke is perceived differently than other household risks. Previously, both instruments relied on item reliability and content validity testing. This study provides a basis for further instrument revision and theoretical testing. © 2012 Blackwell Publishing Ltd.

  14. Food Service Supervisor. Dietetic Support Personnel Achievement Test.

    Science.gov (United States)

    Oklahoma State Dept. of Vocational and Technical Education, Stillwater.

    This guide contains a series of multiple-choice items and guidelines to assist instructors in composing criterion-referenced tests for use in the food service supervisor component of Oklahoma's Dietetic Support Personnel training program. Test items addressing each of the following occupational duty areas are provided: human relations; nutrient…

  15. Food Production Worker. Dietetic Support Personnel Achievement Test.

    Science.gov (United States)

    Oklahoma State Dept. of Vocational and Technical Education, Stillwater.

    This guide contains a series of multiple-choice items and guidelines to assist instructors in composing criterion-referenced tests for use in the food production worker component of Oklahoma's Dietetic Support Personnel training program. Test items addressing each of the following occupational duty areas are provided: human relations; hygiene and…

  16. Food Service Worker. Dietetic Support Personnel Achievement Test.

    Science.gov (United States)

    Oklahoma State Dept. of Vocational and Technical Education, Stillwater.

    This guide contains a series of multiple-choice items and guidelines to assist instructors in composing criterion-referenced tests for use in the food service worker component of Oklahoma's Dietetic Support Personnel training program. Test items addressing each of the following occupational duty areas are provided: human relations; personal…

  17. Testing of tunnel support : dynamic load testing of rockbolt elements to provide data for safer support design.

    CSIR Research Space (South Africa)

    Ortlepp, WD

    1998-06-01

    Full Text Available This research report discusses the development of a realistic and controllable method of testing support tendons dynamically, which has been achieved in this research project, offers a new and fresh opportunity for improving the design methodology...

  18. Industrial hygiene support of underground operations at the Nevada Test Site

    International Nuclear Information System (INIS)

    Porter, P.F.

    1992-01-01

    The Industrial Hygiene Section of the Health Protection Department provides industrial hygiene support of underground operations at the Nevada Test Site. This report describes support operations and summarizes the industrial hygiene data collected from July 31, 1989 through June 30, 1991. Air quality data were collected by means of personnel sampling by active and passive techniques using various kinds of industrial hygiene instrumentation and through localized and general area monitoring. The data collected were used to evaluate underground air quality and quantity requirements; evaluate worker exposures to a variety of air contaminants; determine the applicability and effectiveness of personal protective equipment

  19. Re-irradiation tests of spent fuel at JMTR by means of re-instrumentation technique

    International Nuclear Information System (INIS)

    Nakamura, Jinichi; Shimizu, Michio; Endo, Yasuichi; Nabeya, Hideaki; Ichise, Kenichi; Saito, Junichi; Oshima, Kunio; Uetsuka, Hiroshi

    1999-01-01

    JAERI has developed re-irradiation test procedures of spent fuel irradiated at commercial reactor by means of re-instrumentation technique. Full length rods irradiated at commercial LWRs were re-fabricated to short length rods, and rod inner pressure gauges and fuel center thermocouples were re-instrumented to the rods. Re-irradiation tests to study the fuel behavior during power change were carried out by means of BOCA/OSF-1 facility at the JMTR. In the tests to study the fission gas release during power change, the rod inner pressure increase was observed during power change, especially during power reduction. The fission gas release during power reduction is estimated to be the release from fission gas bubbles on the grain boundary caused by the thermal stress in the pellet during power reduction. Re-irradiation test of gadolinia added fuel was performed by means of dual re-instrumentation technique (fuel center thermocouples and rod inner pressure gauge). A stepwise fission gas release during power change, and the following fuel center temperature change due to gap conductance change were observed. (author)

  20. The CG1 instrument development test station at the high flux isotope reactor

    Science.gov (United States)

    Crow, Lowell; Robertson, Lee; Bilheux, Hassina; Fleenor, Mike; Iverson, Erik; Tong, Xin; Stoica, Ducu; Lee, W. T.

    2011-04-01

    The CG1 instrument development station at the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory began commissioning operation in 2009. When completed, the station will have four beams. CG1A is a 4.22 Å monochromatic beam intended for spin-echo resolved grazing incidence scattering (SERGIS) prototype development. Initial beam operation and characterization are in progress. CG1B will be a 2.35 Å monochromatic beam for a 2-axis utility diffractometer for sample alignment and monochromator development. CG1C will have a double-bounce monochromator system, which will produce a variable wavelength beam from about 1.8-6.4 Å, and will be used for imaging and optical development. The CG1D beam is a single chopper time-of-flight system, used for instrument prototype and component testing. The cold neutron spectrum, with an integrated flux of about 2.7×109 n/cm2 s, has a guide cutoff at 0.8 Å and useful wavelengths greater than 20 Å.Initial results from CG1 include spectral characterization, imaging tests, detector trials, and polarizer tests. An overview of recent tests will be presented, and upcoming instrument prototype efforts will be described.

  1. Predicting Falls in Parkinson Disease: What Is the Value of Instrumented Testing in OFF Medication State?

    Directory of Open Access Journals (Sweden)

    Martina Hoskovcová

    Full Text Available Falls are a common complication of advancing Parkinson's disease (PD. Although numerous risk factors are known, reliable predictors of future falls are still lacking. The objective of this prospective study was to investigate clinical and instrumented tests of balance and gait in both OFF and ON medication states and to verify their utility in the prediction of future falls in PD patients.Forty-five patients with idiopathic PD were examined in defined OFF and ON medication states within one examination day including PD-specific clinical tests, instrumented Timed Up and Go test (iTUG and computerized dynamic posturography. The same gait and balance tests were performed in 22 control subjects of comparable age and sex. Participants were then followed-up for 6 months using monthly fall diaries and phone calls.During the follow-up period, 27/45 PD patients and 4/22 control subjects fell one or more times. Previous falls, fear of falling, more severe motor impairment in the OFF state, higher PD stage, more pronounced depressive symptoms, higher daily levodopa dose and stride time variability in the OFF state were significant risk factors for future falls in PD patients. Increased stride time variability in the OFF state in combination with faster walking cadence appears to be the most significant predictor of future falls, superior to clinical predictors.Incorporating instrumented gait measures into the baseline assessment battery as well as accounting for both OFF and ON medication states might improve future fall prediction in PD patients. However, instrumented testing in the OFF state is not routinely performed in clinical practice and has not been used in the development of fall prevention programs in PD. New assessment methods for daylong monitoring of gait, balance and falls are thus required to more effectively address the risk of falling in PD patients.

  2. Diagnostic development and support of MHD test facilities: Technical progress report for the period January, February, March 1985

    International Nuclear Information System (INIS)

    Shepard, W.S.; Cook, R.L.

    1985-04-01

    Mississippi State University is developing diagnostic instruments for MHD power train data acquisition and for support of MHD component development test facilities. Microprocessor-controlled optical instruments, initially developed for HRSR support, are being refined, and new systems to measure temperatures and gas-seed-slag stream characteristics are being developed. To further data acquisition and analysis capabilities, the diagnostic systems are being interfaced with MHD Energy Center computers. Additionally, technical support of the diagnostic needs of the national MHD research effort is being provided

  3. Modelling of XCO2 Surfaces Based on Flight Tests of TanSat Instruments

    Directory of Open Access Journals (Sweden)

    Li Li Zhang

    2016-11-01

    Full Text Available The TanSat carbon satellite is to be launched at the end of 2016. In order to verify the performance of its instruments, a flight test of TanSat instruments was conducted in Jilin Province in September, 2015. The flight test area covered a total area of about 11,000 km2 and the underlying surface cover included several lakes, forest land, grassland, wetland, farmland, a thermal power plant and numerous cities and villages. We modeled the column-average dry-air mole fraction of atmospheric carbon dioxide (XCO2 surface based on flight test data which measured the near- and short-wave infrared (NIR reflected solar radiation in the absorption bands at around 760 and 1610 nm. However, it is difficult to directly analyze the spatial distribution of XCO2 in the flight area using the limited flight test data and the approximate surface of XCO2, which was obtained by regression modeling, which is not very accurate either. We therefore used the high accuracy surface modeling (HASM platform to fill the gaps where there is no information on XCO2 in the flight test area, which takes the approximate surface of XCO2 as its driving field and the XCO2 observations retrieved from the flight test as its optimum control constraints. High accuracy surfaces of XCO2 were constructed with HASM based on the flight’s observations. The results showed that the mean XCO2 in the flight test area is about 400 ppm and that XCO2 over urban areas is much higher than in other places. Compared with OCO-2’s XCO2, the mean difference is 0.7 ppm and the standard deviation is 0.95 ppm. Therefore, the modelling of the XCO2 surface based on the flight test of the TanSat instruments fell within an expected and acceptable range.

  4. Instrumentation, control and data acquisition system with multiple configurations for test in nuclear environment

    Energy Technology Data Exchange (ETDEWEB)

    Monti, Chiara, E-mail: chiara.monti@enea.it; Neri, Carlo; Pollastrone, Fabio

    2015-10-15

    Highlights: • ENEA developed and characterized a first prototype of the In-Vessel Viewing System (IVVS) probe for ITER. • Piezo motor technology to be used in IVVS probe was tested in neutrons, gamma radiations, high temperature, vacuum and high magnetic fields. • A general architecture of the Data Acquisition and Control System (DACS) was defined and then specialized for each test. • The test campaign has validated instrumentation solutions, which can be effectively used in final IVVS implementation or other ITER diagnostics or applications. - Abstract: The In-Vessel Viewing System is a 3D laser scanning system which will be used to inspect the blanket first wall in ITER. To make the IVVS probe design compatible with the harsh environmental conditions present in ITER, a test campaign was performed in 2012–2013 to verify the adequacy of the main components of the IVVS probe. The IVVS components inspected were an optical encoder, passive components and two customized ultrasonic piezoceramic motors that were instrumented with various sensors. A general architecture of the Data Acquisition and Control System (DACS) was defined and then specialized for each test. To be suitable for this test campaign, the DACS had to host various I/O modules and to properly interface the driver of the customized piezo motors, in order to permit the full control of the test and the acquisition of experimental data. This paper presents the instrumentation solutions designed and implemented for different facilities constraints and the related DACS developed in four specialized versions for the described test campaign.

  5. Childhood lead poisoning investigations: evaluating a portable instrument for testing soil lead.

    Science.gov (United States)

    Reames, Ginger; Lance, Larrie L

    2002-04-01

    The Childhood Lead Poisoning Prevention Branch of the California Department of Health Services evaluated a portable X-ray fluorescence (XRF) instrument for use as a soil lead-testing tool during environmental investigations of lead-poisoned children's homes. A Niton XRF was used to test soil at 119 sampling locations in the yards of 11 San Francisco Bay Area houses. Niton XRF readings were highly correlated with laboratory results and met the study criteria for an acceptable screening method. The data suggest that the most health-protective and time-efficient approach to testing for soil lead above regulatory levels is to take either surface readings or readings of a test cup of soil prepared by grinding with a mortar and pestle. The advantage of the test cup method is that the test cup with soil may be submitted to a laboratory for confirmatory analysis.

  6. Reliability of safety-instrumented systems subject to partial testing and common-cause failures

    International Nuclear Information System (INIS)

    Jin, Hui; Rausand, Marvin

    2014-01-01

    Partial testing is sometimes used as a supplement to proof testing to improve the reliability of safety-instrumented systems (SISs) in low-demand mode of operation. This paper studies the effect of partial testing on SIS reliability. Simplified formulas are developed to include both partial and proof testing in the calculation of the average probability of failure on demand (PFD avg ). The proposed formulas can handle situations where partial testing is performed periodically and non-periodically. Common-cause failures (CCFs) are treated by using the beta-factor model, and different β-factors can be included for different failure modes. The proposed formulas are compared with existing results for partial verification. A case study is presented to demonstrate the applicability. The proposed formulas can serve as a valuable tool for selecting a cost-effective strategy for partial testing

  7. The Caregiver Contribution to Heart Failure Self-Care (CACHS): Further Psychometric Testing of a Novel Instrument.

    Science.gov (United States)

    Buck, Harleah G; Harkness, Karen; Ali, Muhammad Usman; Carroll, Sandra L; Kryworuchko, Jennifer; McGillion, Michael

    2017-04-01

    Caregivers (CGs) contribute important assistance with heart failure (HF) self-care, including daily maintenance, symptom monitoring, and management. Until CGs' contributions to self-care can be quantified, it is impossible to characterize it, account for its impact on patient outcomes, or perform meaningful cost analyses. The purpose of this study was to conduct psychometric testing and item reduction on the recently developed 34-item Caregiver Contribution to Heart Failure Self-care (CACHS) instrument using classical and item response theory methods. Fifty CGs (mean age 63 years ±12.84; 70% female) recruited from a HF clinic completed the CACHS in 2014 and results evaluated using classical test theory and item response theory. Items would be deleted for low (.95) endorsement, low (.7) corrected item-total correlations, significant pairwise correlation coefficients, floor or ceiling effects, relatively low latent trait and item information function levels ( .5), and differential item functioning. After analysis, 14 items were excluded, resulting in a 20-item instrument (self-care maintenance eight items; monitoring seven items; and management five items). Most items demonstrated moderate to high discrimination (median 2.13, minimum .77, maximum 5.05), and appropriate item difficulty (-2.7 to 1.4). Internal consistency reliability was excellent (Cronbach α = .94, average inter-item correlation = .41) with no ceiling effects. The newly developed 20-item version of the CACHS is supported by rigorous instrument development and represents a novel instrument to measure CGs' contribution to HF self-care. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

  8. Food-related lifestyles in Singapore: Testing a Western European research instrument in Southeast Asia

    DEFF Research Database (Denmark)

    Askegaard, Søren; Brunsø, Karen; Crippen, Kaye

    , and to interpret similarities and differences found. For this purpose, data have been collected in Singaporean families using the food-related life style insrurment. A total of 89 questionnaires form the basis of the analysis. First, the cross-cultural validity of the instrument is tested, and secondly......, in the light of those results, we interpret the results in relationship to local food cultures....

  9. Developing and testing an instrument for identifying performance incentives in the Greek health care sector

    Directory of Open Access Journals (Sweden)

    Paleologou Victoria

    2006-09-01

    Full Text Available Abstract Background In the era of cost containment, managers are constantly pursuing increased organizational performance and productivity by aiming at the obvious target, i.e. the workforce. The health care sector, in which production processes are more complicated compared to other industries, is not an exception. In light of recent legislation in Greece in which efficiency improvement and achievement of specific performance targets are identified as undisputable health system goals, the purpose of this study was to develop a reliable and valid instrument for investigating the attitudes of Greek physicians, nurses and administrative personnel towards job-related aspects, and the extent to which these motivate them to improve performance and increase productivity. Methods A methodological exploratory design was employed in three phases: a content development and assessment, which resulted in a 28-item instrument, b pilot testing (N = 74 and c field testing (N = 353. Internal consistency reliability was tested via Cronbach's alpha coefficient and factor analysis was used to identify the underlying constructs. Tests of scaling assumptions, according to the Multitrait-Multimethod Matrix, were used to confirm the hypothesized component structure. Results Four components, referring to intrinsic individual needs and external job-related aspects, were revealed and explain 59.61% of the variability. They were subsequently labeled: job attributes, remuneration, co-workers and achievement. Nine items not meeting item-scale criteria were removed, resulting in a 19-item instrument. Scale reliability ranged from 0.782 to 0.901 and internal item consistency and discriminant validity criteria were satisfied. Conclusion Overall, the instrument appears to be a promising tool for hospital administrations in their attempt to identify job-related factors, which motivate their employees. The psychometric properties were good and warrant administration to a larger

  10. Methodological Issue in Pragmatic Research: is Discourse Completion Test a Reliable Data Collection Instrument?

    OpenAIRE

    Nurani, Lusia Marliana

    2009-01-01

    In pragmatic research One of the data collection instrument whichreleability is being questioned about its reliability is the Discourse Completion Test (DCT). This issue appears due to several weaknesses of DCT. Firstly, the authenticity of the situations is limited. Then, the hypothetical nature of the situations in DCT simplifies the complexity of interactions in real conversation. Moreover, what people claim they would say in the hypothetical situation is not necessarily what they actually...

  11. PTC test bed upgrades to provide ACSES testing support capabilities at transportation technology center.

    Science.gov (United States)

    2015-06-01

    FRA Task Order 314 upgraded the Positive Train Control (PTC) Test Bed at the Transportation Technology Center to support : testing of PTC systems, components, and related equipment associated with the Advanced Civil Speed Enforcement System : (ACSES)...

  12. Layout of PWR in-core instrumentation system tubing and support structure with Bechtel 3D-CADD

    International Nuclear Information System (INIS)

    Ichikawa, T.; Pfeifer, B.W.; Mulay, J.N.

    1987-01-01

    The optimization study of the PWR In-Core Instrumentation System (ICIS) tubing layout and support structure presented an opportunity to utilize the Bechtel 3D-CADD program to perform this task. This paper provides a brief summary of the Bechtel 3D-CADD program development and capabilities and outlines the process of developing and optimizing the ICIS tube layout. Specific aspects relating to the ICIS tube layout criteria, support, alignment, electronic interference check and erection sequence are provided. (orig.)

  13. Proposal for a Universal Test Mirror for Characterization of SlopeMeasuring Instruments

    Energy Technology Data Exchange (ETDEWEB)

    Yashchuk, Valeriy V.; McKinney, Wayne R.; Warwick, Tony; Noll,Tino; Siewert, Frank; Zeschke, Thomas; Geckeler, Ralf D.

    2007-07-31

    The development of third generation light sources like theAdvanced Light Source (ALS) or BESSY II brought to a focus the need forhigh performance synchrotron optics with unprecedented tolerances forslope error and micro roughness. Proposed beam lines at Free ElectronLasers (FEL) require optical elements up to a length of one meter,characterized by a residual slope error in the range of 0.1murad (rms),and rms values of 0.1 nm for micro roughness. These optical elements mustbe inspected by highly accurate measuring instruments, providing ameasurement uncertainty lower than the specified accuracy of the surfaceunder test. It is essential that metrology devices in use at synchrotronlaboratories be precisely characterized and calibrated to achieve thistarget. In this paper we discuss a proposal for a Universal Test Mirror(UTM) as a realization of a high performance calibration instrument. Theinstrument would provide an ideal calibration surface to replicate aredundant surface under test of redundant figure. The application of asophisticated calibration instrument will allow the elimination of themajority of the systematic error from the error budget of an individualmeasurement of a particular optical element. We present the limitationsof existing methods, initial UTM design considerations, possiblecalibration algorithms, and an estimation of the expectedaccuracy.

  14. Report mapping legal and policy instruments of the EU for human rights and democracy support, FRAME Deliverable 12.1

    NARCIS (Netherlands)

    Churruca Muguruza, C.; Isa, F. G.; San José, D. G.; Fernández Sánchez, P. A.; Márquez Carrasco, C.; Muñoz Nogal, E.; Nagore Casas, M.; Timmer, Alexandra|info:eu-repo/dai/nl/351098852

    2014-01-01

    This report is devoted to the mapping of legal and policy instruments of the EU for human rights and democracy support. In particular, it highlights the EU´s human rights priorities in terms of themes and vulnerable groups in its external action based on a review of EU policy documents and

  15. Development and testing of an instrument to measure protective nursing advocacy.

    Science.gov (United States)

    Hanks, Robert G

    2010-03-01

    Patient advocacy is an important aspect of nursing care, yet there are few instruments to measure this essential function. This study was conducted to develop, determine the psychometric properties, and support validity of the Protective Nursing Advocacy Scale (PNAS), which measures nursing advocacy beliefs and actions from a protective perspective. The study used a descriptive correlational design with a systematically selected sample of 419 medical-surgical registered nurses. Analysis of the 43-item instrument was conducted using principal components analysis with promax rotation, which resulted in the items loading onto four components. The four subscales have sufficient internal consistency, as did the overall PNAS. Satisfactory evidence of construct, content, and convergent validity were determined. Implications for nursing practice include using the PNAS in conjunction with an educational program to enhance advocacy skills, which may help to improve patient outcomes.

  16. Instrument performance evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Swinth, K.L.

    1993-03-01

    Deficiencies exist in both the performance and the quality of health physics instruments. Recognizing the implications of such deficiencies for the protection of workers and the public, in the early 1980s the DOE and the NRC encouraged the development of a performance standard and established a program to test a series of instruments against criteria in the standard. The purpose of the testing was to establish the practicality of the criteria in the standard, to determine the performance of a cross section of available instruments, and to establish a testing capability. Over 100 instruments were tested, resulting in a practical standard and an understanding of the deficiencies in available instruments. In parallel with the instrument testing, a value-impact study clearly established the benefits of implementing a formal testing program. An ad hoc committee also met several times to establish recommendations for the voluntary implementation of a testing program based on the studies and the performance standard. For several reasons, a formal program did not materialize. Ongoing tests and studies have supported the development of specific instruments and have helped specific clients understand the performance of their instruments. The purpose of this presentation is to trace the history of instrument testing to date and suggest the benefits of a centralized formal program.

  17. Temperature evaluation of an instrumented capsule after material irradiation tests in HANARO

    International Nuclear Information System (INIS)

    Choi, M.H.; Choo, K.N.; Kim, H.R.; Kim, B.G.

    2007-01-01

    An instrumented capsule has been used for an irradiation test of various nuclear materials in the research reactor, HANARO. The capsule is designed to have a standard 4-hole structure for the economical test of an RPV material at 290 ± 10 deg. C. The temperature of the specimens for the reactor powers, 0-24 MW, is measured by 12 thermocouples, and finite element (FE) analyses are also performed to compare and verify the irradiation test results. As a result of the tests and analyses, the maximum temperature at the reactor power of 24 MW is 256 deg. C for an irradiation test and 202.6 deg. C for an FE analysis at Stage 3 of the capsule. Also, for each stage of the capsule, the temperature difference of the specimen in the axial direction is very small to within 10 deg. C. It is expected that the results presented in this paper will be useful when designing the instrumented capsules for an irradiation test

  18. Field instrumentation and testing needs for a high level waste repository

    International Nuclear Information System (INIS)

    Marti, J.; Maini, T.

    1981-03-01

    A review has been conducted of the testing and measurement needs posed by a deep geologic High Level Waste (HLW) repository in crystalline or argillaceous rocks. Siting, design, construction, operation and decommissioning of the repository have been covered, together with the planning of a Test and Demonstration Facility. Instruments and methods available have been critically assessed in their ability to fulfil the aforementioned testing and monitoring programmes. Special attention has been paid to the relation of measurements to the data needs and to the tests likely to generate such data. This assessment has concentrated on measurements of absolute rock stresses, monitoring of changes in rock stress, evaluation of the rock mass deformability, measurement of relative displacements and determination of the hydrogeologic parameters of the rock mass. Other measurements have been studied with a lesser degree of attention. The overall conclusion is that, from the instrumentation and testing points of view, present plans for a test and demonstration facility in the early nineties and a repository soon after 2000 are indeed feasible. Specific conclusions on the state-of-the-art and development needs are presented in the report. (author)

  19. Ethical issues in palliative care for nursing homes: Development and testing of a survey instrument.

    Science.gov (United States)

    Preshaw, Deborah Hl; McLaughlin, Dorry; Brazil, Kevin

    2018-02-01

    To develop and psychometrically assess a survey instrument identifying ethical issues during palliative care provision in nursing homes. Registered nurses and healthcare assistants have reported ethical issues in everyday palliative care provision. Identifying these issues provides evidence to inform practice development to support healthcare workers. Cross-sectional survey of Registered nurses and healthcare assistants in nursing homes in one region of the UK. A survey instrument, "Ethical issues in Palliative Care for Nursing homes", was developed through the findings of qualitative interviews with Registered nurses and healthcare assistants in nursing homes and a literature review. It was reviewed by an expert panel and piloted prior to implementation in a survey in 2015 with a convenience sample of 596 Registered nurses and healthcare assistants. Descriptive and exploratory factor analyses were used to assess the underlying structure of the Frequency and Distress Scales within the instrument. Analysis of 201 responses (response rate = 33.7%) revealed four factors for the Frequency Scale and five factors for the Distress Scale that comprise the Ethical issues in Palliative Care for Nursing homes. Factors common to both scales included "Processes of care," "Resident autonomy" and "Burdensome treatment." Additionally, the Frequency Scale included "Competency," and the Distress Scale included "Quality of care" and "Communication." The Ethical issues in Palliative Care for Nursing homes instrument has added to the palliative care knowledge base by considering the ethical issues experienced specifically by Registered nurses and healthcare assistants within the nursing home. This research offers preliminary evidence of the psychometric properties of the Ethical issues in Palliative Care for Nursing homes survey instrument. The two largest factors highlight the need to address the organisational aspects of caring and provide training in negotiating conflicting

  20. Briefer assessment of social network drinking: A test of the Important People Instrument-5 (IP-5).

    Science.gov (United States)

    Hallgren, Kevin A; Barnett, Nancy P

    2016-12-01

    The Important People instrument (IP; Longabaugh et al., 2010) is one of the most commonly used measures of social network drinking. Although its reliability and validity are well-supported, the length of the instrument may limit its use in many settings. The present study evaluated whether a briefer, 5-person version of the IP (IP-5) adequately reproduces scores from the full IP. College freshmen (N = 1,053) reported their own past-month drinking, alcohol-related consequences, and information about drinking in their close social networks at baseline and 1 year later. From this we derived network members' drinking frequency, percentage of drinkers, and percentage of heavy drinkers, assessed for up to 10 (full IP) or 5 (IP-5) network members. We first modeled the expected concordance between full-IP scores and scores from simulated shorter IP instruments by sampling smaller subsets of network members from full IP data. Then, using quasi-experimental methods, we administered the full IP and IP-5 and compared the 2 instruments' score distributions and concurrent and year-lagged associations with participants' alcohol consumption and consequences. Most of the full-IP variance was reproduced from simulated shorter versions of the IP (ICCs ≥ 0.80). The full IP and IP-5 yielded similar score distributions, concurrent associations with drinking (r = 0.22 to 0.52), and year-lagged associations with drinking. The IP-5 retains most of the information about social network drinking from the full IP. The shorter instrument may be useful in clinical and research settings that require frequent measure administration, yielding greater temporal resolution for monitoring social network drinking. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

  1. UPTF test instrumentation. Measurement system identification, engineering units and computed parameters

    International Nuclear Information System (INIS)

    Sarkar, J.; Liebert, J.; Laeufer, R.

    1992-11-01

    This updated version of the previous report /1/ contains, besides additional instrumentation needed for 2D/3D Programme, the supplementary instrumentation in the inlet plenum of SG simulator and hot and cold leg of broken loop, the cold leg of intact loops and the upper plenum to meet the requirements (Test Phase A) of the UPTF Programme, TRAM, sponsored by the Federal Minister of Research and Technology (BMFT) of the Federal Republic of Germany. For understanding, the derivation and the description of the identification codes for the entire conventional and advanced measurement systems classifying the function, and the equipment unit, key, as adopted in the conventional power plants, have been included. Amendments have also been made to the appendices. In particular, the list of measurement systems covering the measurement identification code, instrument, measured quantity, measuring range, band width, uncertainty and sensor location has been updated and extended to include the supplementary instrumentation. Beyond these amendments, the uncertainties of measurements have been precisely specified. The measurement identification codes which also stand for the identification of the corresponding measured quantities in engineering units and the identification codes derived therefrom for the computed parameters have been adequately detailed. (orig.)

  2. Use of instrumented charpy tests to determine onset of upper-shelf energy

    International Nuclear Information System (INIS)

    Canonico, D.A.; Stelzman, W.J.; Berggren, R.G.; Nanstad, R.K.

    1975-11-01

    The Charpy V-notch (C/sub v/) upper-shelf energy is usually defined as that temperature range in which the surface of the C/sub v/ specimen exhibits an appearance indicative of a 100 percent ductile fracture. In an attempt to avoid the need for interpretation, the selection of the C/sub v/ upper-shelf energy is based on the results from an instrumented impact test which provides a permanent record of the load-deflection history of a C/sub v/ specimen during the testing sequence. In the brittle-ductile transition temperature regime, a precipitous drop in the load trace occurs. The amount of the drop decreases at higher temperatures until it is zero, and the zero-drop-in-load temperature is identical to the onset of the C/sub v/ upper shelf. This relationship between the drop in load and energy in an instrumented impact test provides incontestable assurance that the C/sub v/ upper shelf has been obtained. This relationship between drop in load and temperature permits a prediction of the onset of the upper-shelf temperature with as few as two instrumented impact tests. It is also shown that nil-ductility temperature (NDT) (determined by the drop-weight test) is released to the C/sub v/ upper shelf. For the SA-508 Class 2 and SA-533 Grade B Class 1 steels employed in the fabrication of pressure vessels for light-water reactors, C/sub v/ testing at NDT + 180 0 F (100 0 C) will provide upper-shelf energy values

  3. [Utilization of the screening test for discharge support].

    Science.gov (United States)

    Ikedo, Hasue; Morimoto, Ritsuko; Matsumoto, Saeko; Nakajo, Ikuko; Nakagawa, Michiyo

    2005-12-01

    We hand out a list of screening tests for discharge support (the screening) to all patients upon admission, so that they can receive an early discharge. Implementing the screening as a balanced score card (BSC) evaluation index of the work performance by the nursing division, we were able to screen more than 40% of newly admitted patients immediately after the introduction of the screening. When more than two items of the screening questionnaire were checked, a discharge support intervention was introduced. Patients who checked items on the screening questionnaire have tended to request discharge support within a week of admission.

  4. Apparatus for friction tests of support elements in fusion devices

    Science.gov (United States)

    Gradt, Th; Aßmus, K.; Börner, H.; Schneider, Th

    2008-03-01

    Spacers and supports belong to the critical elements in the structure of a nuclear fusion device, particularly, when they are installed in the vacuum or superconducting magnet system of the reactor. These supports have to sustain high loads while allowing a certain amount of tangential movement with low friction and without any stick-slip motion. Vacuum and cryogenic environments are extremely hostile for smooth sliding systems, because conventional liquid lubricants cannot be employed, and only a very limited number of materials for dry sliding systems under these conditions are available. In order to test the friction behaviour of support elements in the field coils of the fusion experiment WENDELSTEIN 7-X, a test rig was build which allows testing in liquid helium environment at 4.2 K, with a normal force up to 150 kN, and a sliding velocity of 0.1 mm/s in oscillating motion. First tests have shown that the apparatus is appropriate for simulating the sliding behaviour of support elements. As an example, a result of an earlier model test of an MoS2-coating is shown.

  5. Testing in Support of Space Fission System Development and Qualification

    Science.gov (United States)

    Houts, Mike; Bragg-Sitton, Shannon; Garber, Anne; Godfrey, Tom; Martin, Jim; Pearson, Boise; Webster, Kenny

    2007-01-01

    Extensive data would be required for the qualification of a fission surface power (FSP) system. The strategy for qualifying a FSP system could have a significant programmatic impact. This paper explores potential options that could be used for qualifying FSP systems, including cost-effective means for obtaining required data. three methods for obtaining qualification data are analysis, non-nuclear testing, and nuclear testing. It has been over 40 years since the US qualified a space reactor for launch. During that time, advances have been made related to all three methods. Perhaps the greatest advancement has occurred in the area of computational tools for design and analysis. Tools that have been developed, coupled with modem computers, would have a significant impact on a FSP qualification. This would be especially true for systems with materials and fuels operating well within temperature, irradiation damage, and burnup limits. The ability to perform highly realistic non-nuclear testing has also advanced throughout the past four decades. Instrumented thermal simulators were developed during the 1970s and 1980s to assist in the development, operation, and assessment of terrestrial fission systems. Instrumented thermal simulators optimized for assisting in the development, operation, and assessment of modem FSP systems have been under development (and utilized) since 1998. These thermal simulators enable heat from fission to be closely mimicked (axial power profile, radial power profile, temperature, heat flux, etc.} and extensive data to be taken from the core region. Both steady-state and transient operation can be tested. For transient testing, reactivity feedback is calculated (or measured in cold/warm criticals) based on reactor temperature and/or dimensional changes. Pin power during a transient is then calculated based on the reactivity feedback that would occur given measured values of temperature and/or dimensional change. In this way nonnuclear testing

  6. Proof-testing strategies induced by dangerous detected failures of safety-instrumented systems

    International Nuclear Information System (INIS)

    Liu, Yiliu; Rausand, Marvin

    2016-01-01

    Some dangerous failures of safety-instrumented systems (SISs) are detected almost immediately by diagnostic self-testing as dangerous detected (DD) failures, whereas other dangerous failures can only be detected by proof-testing, and are therefore called dangerous undetected (DU) failures. Some items may have a DU- and a DD-failure at the same time. After the repair of a DD-failure is completed, the maintenance team has two options: to perform an insert proof test for DU-failure or not. If an insert proof test is performed, it is necessary to decide whether the next scheduled proof test should be postponed or performed at the scheduled time. This paper analyzes the effects of different testing strategies on the safety performance of a single channel of a SIS. The safety performance is analyzed by Petri nets and by approximation formulas and the results obtained by the two approaches are compared. It is shown that insert testing improves the safety performance of the channel, but the feasibility and cost of the strategy may be a hindrance to recommend insert testing. - Highlights: • Identify the tests induced by detected failures. • Model the testing strategies following DD-failures. • Propose analytical formulas for effects of strategies. • Simulate and verify the proposed models.

  7. Development of diagnostic test instruments to reveal level student conception in kinematic and dynamics

    Science.gov (United States)

    Handhika, J.; Cari, C.; Suparmi, A.; Sunarno, W.; Purwandari, P.

    2018-03-01

    The purpose of this research was to develop a diagnostic test instrument to reveal students' conceptions in kinematics and dynamics. The diagnostic test was developed based on the content indicator the concept of (1) displacement and distance, (2) instantaneous and average velocity, (3) zero and constant acceleration, (4) gravitational acceleration (5) Newton's first Law, (6) and Newton's third Law. The diagnostic test development model includes: Diagnostic test requirement analysis, formulating test-making objectives, developing tests, checking the validity of the content and the performance of reliability, and application of tests. The Content Validation Index (CVI) results in the category are highly relevant, with a value of 0.85. Three questions get negative Content Validation Ratio CVR) (-0.6), after revised distractors and clarify visual presentation; the CVR become 1 (highly relevant). This test was applied, obtained 16 valid test items, with Cronbach Alpha value of 0.80. It can conclude that diagnostic test can be used to reveal the level of students conception in kinematics and dynamics.

  8. Design of the dual instrumented fuel rods to measure the nuclear fuel characteristics during Irradiation test at HANARO

    International Nuclear Information System (INIS)

    Sohn, Jae Min; Oh, Jong Myung; Cho, Man Soon; Choo, Ki nam; Choi, Myung Hwan; Lee, Dong Soo; Kim, Boong Goo; Kim, Young Jin

    2005-01-01

    The instrumented capsule for the nuclear fuel irradiation test (hereinafter referred to instrumented fuel capsule), which are crucial for the verification of a nuclear fuel performance and safety, have been developed at HANARO(High-flux Advanced Neutron Application Reactor). The irradiation test of the first instrumented fuel capsule(02F-11K) was carried out in March 2003 for 1,296 MWD(Mega Watt Day) and the irradiation test of the second instrumented fuel capsule(03F-05K) was carried out in April 2004 for 1,533MWD at HANARO. Through the irradiation tests of the two capsules, the design specifications and safety of the instrumented fuel capsule were verified successfully. In the 02F-11K instrumented fuel capsule, only the technologies for measuring the center temperature of the nuclear fuel and neutron flux were implemented. In the 03F-05K instrumented fuel capsule, the technologies for measuring the center temperature of the nuclear fuel, the internal pressure of the fuel rod, the elongation of the nuclear fuel and the neutron flux were implemented. The purpose of this paper is to develop the dual instrumented technology that enables two characteristics to be measured simultaneously in one fuel rod. Therefore, this paper presents the design of the dual instrumented fuel rods and the plan of the irradiation test for the newly designed fuel rods

  9. Cryo-Vacuum Testing of JWST's Integrated Telescope & Scientific Instrument Suite (OTIS)

    Science.gov (United States)

    Kimble, Randy; Apollo, Peter; Feinberg, Lee; Glazer, Stuart; Hanley, Jeffrey; Keski-Kuha, Ritva; Kirk, Jeffrey; Knight, J. Scott; Lambros, Scott; Lander, Juli; McGuffey, Douglas; Mehalick, Kimberly; Ohl, Raymond; Ousley, Wes; Reis, Carl; Reynolds, Paul; Begoña Vila, Maria; Waldman, Mark; Whitman, Tony

    2018-01-01

    A year ago we reported on the planning for a major test in the James Webb Space Telescope (JWST) program: cryo-vacuum testing of the combination of the Optical Telescope Element (OTE) and the Integrated Science Instrument Module (ISIM). The cryo-vacuum testing of that scientific heart of the JWST observatory, known as OTIS (= OTE + ISIM), has now been completed in historic chamber A at NASA’s Johnson Space Center. From July through October 2017, the flight payload was cooled to its operating temperatures, put through a comprehensive suite of optical, thermal, and operational tests, and then safely warmed back to room temperature. We report here on the execution and top-level results from this milestone event in the JWST program.

  10. Instrumentation, Field Network And Process Automation for the LHC Cryogenic Line Tests

    CERN Document Server

    Bager, T; Bertrand, G; Casas-Cubillos, J; Gomes, P; Parente, C; Riddone, G; Suraci, A

    2000-01-01

    This paper describes the cryogenic control system and associated instrumentation of the test facility for 3 pre-series units of the LHC Cryogenic Distribution Line. For each unit, the process automation is based on a Programmable Logic Con-troller implementing more than 30 closed control loops and handling alarms, in-terlocks and overall process management. More than 160 sensors and actuators are distributed over 150 m on a Profibus DP/PA network. Parameterization, cali-bration and diagnosis are remotely available through the bus. Considering the diversity, amount and geographical distribution of the instru-mentation involved, this is a representative approach to the cryogenic control system for CERN's next accelerator.

  11. Application of the Alcohol, Smoking and Substance Involvement Screening Test (ASSIST) instrument: an integrative review.

    Science.gov (United States)

    Silva, Andrécia Cósmen da; Lucchese, Roselma; Vargas, Lorena Silva; Benício, Patrícia Rosa; Vera, Ivânia

    2016-03-01

    Objective To systematize the knowledge and the learning of how the instrument Alcohol, Smoking and Substance Involvement Screening Test (ASSIST) has been applied. Method Integrative review, performed from May to July 2014, searching the databases Latin American and Caribbean Health Science Literature (LILACS), Medical Literature Analysis and Retrieval System Online (Medline), PubMed and Scientific Electronic Library Online (SciELO), as well as in the search system of the Portal of Journals of the Coordination for the Improvement of Higher Education Personnel (CAPES). We selected 26 articles. Results ASSIST focused on helping the identification and classification of psychoactive substances use, and it has proved to be important in screening the involvement with alcohol and other drugs, and effectiveness in primary health care. Conclusion It was confirmed as an instrument to be used in Health Care.

  12. PEP Support: Laboratory Scale Leaching and Permeate Stability Tests

    Energy Technology Data Exchange (ETDEWEB)

    Russell, Renee L.; Peterson, Reid A.; Rinehart, Donald E.; Buchmiller, William C.

    2010-05-21

    This report documents results from a variety of activities requested by the Hanford Tank Waste Treatment and Immobilization Plant (WTP). The activities related to caustic leaching, oxidative leaching, permeate precipitation behavior of waste as well as chromium (Cr) leaching are: • Model Input Boehmite Leaching Tests • Pretreatment Engineering Platform (PEP) Support Leaching Tests • PEP Parallel Leaching Tests • Precipitation Study Results • Cr Caustic and Oxidative Leaching Tests. Leaching test activities using the PEP simulant provided input to a boehmite dissolution model and determined the effect of temperature on mass loss during caustic leaching, the reaction rate constant for the boehmite dissolution, and the effect of aeration in enhancing the chromium dissolution during caustic leaching. Other tests were performed in parallel with the PEP tests to support the development of scaling factors for caustic and oxidative leaching. Another study determined if precipitate formed in the wash solution after the caustic leach in the PEP. Finally, the leaching characteristics of different chromium compounds under different conditions were examined to determine the best one to use in further testing.

  13. Development and Testing of UCLA's Electron Losses and Fields Investigation (ELFIN) Instrument Payload

    Science.gov (United States)

    Wilkins, C.; Bingley, L.; Angelopoulos, V.; Caron, R.; Cruce, P. R.; Chung, M.; Rowe, K.; Runov, A.; Liu, J.; Tsai, E.

    2017-12-01

    UCLA's Electron Losses and Fields Investigation (ELFIN) is a 3U+ CubeSat mission designed to study relativistic particle precipitation in Earth's polar regions from Low Earth Orbit. Upon its 2018 launch, ELFIN will aim to address an important open question in Space Physics: Are Electromagnetic Ion-Cyclotron (EMIC) waves the dominant source of pitch-angle scattering of high-energy radiation belt charged particles into Earth's atmosphere during storms and substorms? Previous studies have indicated these scattering events occur frequently during storms and substorms, and ELFIN will be the first mission to study this process in-situ.Paramount to ELFIN's success is its instrument suite consisting of an Energetic Particle Detector (EPD) and a Fluxgate Magnetometer (FGM). The EPD is comprised of two collimated solid-state detector stacks which will measure the incident flux of energetic electrons from 50 keV to 4 MeV and ions from 50 keV to 300 keV. The FGM is a 3-axis magnetic field sensor which will capture the local magnetic field and its variations at frequencies up to 5 Hz. The ELFIN spacecraft spins perpendicular to the geomagnetic field to provide 16 pitch-angle particle data sectors per revolution. Together these factors provide the capability to address the nature of radiation belt particle precipitation by pitch-angle scattering during storms and substorms.ELFIN's instrument development has progressed into the late Engineering Model (EM) phase and will soon enter Flight Model (FM) development. The instrument suite is currently being tested and calibrated at UCLA using a variety of methods including the use of radioactive sources and applied magnetics to simulate orbit conditions during spin sectoring. We present the methods and test results from instrument calibration and performance validation.

  14. Advanced Grid Support Functionality Testing for Florida Power and Light

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Austin [National Renewable Energy Lab. (NREL), Golden, CO (United States); Martin, Gregory [National Renewable Energy Lab. (NREL), Golden, CO (United States); Hurtt, James [Florida Power and Light, Juno Beach, FL (United States)

    2017-03-21

    This report describes the results of laboratory testing of advanced photovoltaic (PV) inverter testing undertaken by the National Renewable Energy Laboratory (NREL) on behalf of the Florida Power and Light Company (FPL). FPL recently commissioned a 1.1 MW-AC PV installation on a solar carport at the Daytona International Speedway in Daytona Beach, Florida. In addition to providing a source of clean energy production, the site serves as a live test bed with 36 different PV inverters from eight different manufacturers. Each inverter type has varied support for advanced grid support functions (GSFs) that are becoming increasingly commonplace, and are being required through revised interconnection standards such as UL1741, IEEE1547, and California (CA) Rule 21. FPL is interested in evaluating the trade-offs between different GSFs, their compliance to emerging standards, and their effects on efficiency and reliability. NREL has provided a controlled laboratory environment to undertake such a study. This work covered nine different classes of tests to compare inverter capabilities and performance for four different inverters that were selected by FPL. The test inverters were all three-phase models rated between 24-36 kW, and containing multiple PV input power point trackers. Advanced grid support functions were tested for functional behavior, and included fixed power factor operation, voltage-ride through, frequency ride-through, volt-var control, and frequency-Watt control. Response to abnormal grid conditions with GSFs enabled was studied through anti-islanding, fault, and load rejection overvoltage tests. Finally, efficiency was evaluated across a range of operating conditions that included power factor, output power, and input voltage variations. Test procedures were derived from requirements of a draft revision of UL741, CA Rule 21, and/or previous studies at NREL. This reports summarizes the results of each test case, providing a comparative performance analysis

  15. Two on-line methods for routine testing of neutron and temperature instrumentation of power reactors

    International Nuclear Information System (INIS)

    Edelmann, M.

    1976-07-01

    The testing procedures proposed and described use inherent fluctuations or modulations of the physical quantities being measured as dynamic test input to the whole signal channel. They can be applied therefore during normal reactor operation at power. Signal channel performance information is obtained from the fluctuations of the available signals only using simplified noise analysis techniques. Neutron instrumentation testing is based on the prompt jump in reactor power subsequent to single reactivity steps produced by the control system during normal operation to keep the power at the prescribed level. For testing of outlet temperature instrumentation (thermocouples) a different procedure is necessary. The relationship between temperature and power noise is used. It was found that the ratio of the maximum value of the cross correlation function between neutron and temperature noise signals normalized to the rms value of the neutron noise is a suitable quantity for monitoring. Monitoring with small and large averaging time constants simultaneously enables quick indication of suddenly occuring significant failure and detection of small changes of the response characteristics, respectively. (orig.) [de

  16. James Webb Space Telescope (JWST) Integrated Sciene Instrument Module (ISIM) Cryo-Vac 3 (CV3) Thermal Vacuum Test

    Science.gov (United States)

    Packard, Ed

    2016-01-01

    This presentation describes the test objectives, test summary, test configuration and test performance of the James Webb Space Telescope Integrated Science Instrument Module CryoVac 3 Thermal Vacuum Test. Verify the ISIM System in its final configuration after environmental exposure and provide a post-environmental performance baseline, including critical ground calibrations needed for science data processing in flight.

  17. Clinical Trial Designs to Support Clinical Utility of Pharmacogenomic Testing.

    Science.gov (United States)

    Drozda, Katarzyna; Pacanowski, Michael A

    2017-09-01

    Advancing the use of biomarkers and pharmacogenomics has been a key priority area for the U.S. Food and Drug Administration (FDA). The FDA offers prescribing recommendations to manage ~100 gene-drug interactions, and multiple institutions around the United States and abroad have incorporated genomic testing into patient care. However, the penetration of pharmacogenomic testing remains incomplete. In this perspective, we summarize the evidence streams to support the clinical utility of pharmacogenomic testing and its transition into clinical practice. © 2017 Pharmacotherapy Publications, Inc.

  18. Analysing the interactions between renewable energy promotion and energy efficiency support schemes. The impact of different instruments and design elements

    Energy Technology Data Exchange (ETDEWEB)

    Del Rio, Pablo [Instituto de Politicas y Bienes Publicos, Consejo Superior de Investigaciones Cientificas (CSIC), C/Albasanz 26-28, 28037 Madrid (Spain)

    2010-09-15

    CO{sub 2} emissions reduction, renewable energy deployment and energy efficiency are three main energy/environmental goals, particularly in Europe. Their relevance has led to the implementation of support schemes in these realms. Their coexistence may lead to overlaps, synergies and conflicts between them. The aim of this paper is to analyse the interactions between energy efficiency measures and renewable energy promotion, whereas previous analyses have focused on the interactions between emissions trading schemes (ETS) and energy efficiency measures and ETS and renewable energy promotion schemes. Furthermore, the analysis in this paper transcends the certificate debate (i.e., tradable green and white certificates) and considers other instruments, particularly feed-in tariffs for renewable electricity. The goal is to identify positive and negative interactions between energy efficiency and renewable electricity promotion and to assess whether the choice of specific instruments and design elements within those instruments affects the results of the interactions. (author)

  19. Analysing the interactions between renewable energy promotion and energy efficiency support schemes: The impact of different instruments and design elements

    Energy Technology Data Exchange (ETDEWEB)

    Rio, Pablo del, E-mail: pablo.delrio@cchs.csic.e [Instituto de Politicas y Bienes Publicos, Consejo Superior de Investigaciones Cientificas (CSIC), C/Albasanz 26-28, 28037 Madrid (Spain)

    2010-09-15

    CO{sub 2} emissions reduction, renewable energy deployment and energy efficiency are three main energy/environmental goals, particularly in Europe. Their relevance has led to the implementation of support schemes in these realms. Their coexistence may lead to overlaps, synergies and conflicts between them. The aim of this paper is to analyse the interactions between energy efficiency measures and renewable energy promotion, whereas previous analyses have focused on the interactions between emissions trading schemes (ETS) and energy efficiency measures and ETS and renewable energy promotion schemes. Furthermore, the analysis in this paper transcends the 'certificate' debate (i.e., tradable green and white certificates) and considers other instruments, particularly feed-in tariffs for renewable electricity. The goal is to identify positive and negative interactions between energy efficiency and renewable electricity promotion and to assess whether the choice of specific instruments and design elements within those instruments affects the results of the interactions.

  20. Post-Launch Calibration and Testing of Space Weather Instruments on GOES-R Satellite

    Science.gov (United States)

    Tadikonda, S. K.; Merrow, Cynthia S.; Kronenwetter, Jeffrey A.; Comeyne, Gustave J.; Flanagan, Daniel G.; Todrita, Monica

    2016-01-01

    The Geostationary Operational Environmental Satellite - R (GOES-R) is the first of a series of satellites to be launched, with the first launch scheduled for October 2016. The three instruments Solar UltraViolet Imager (SUVI), Extreme ultraviolet and X-ray Irradiance Sensor (EXIS), and Space Environment In-Situ Suite (SEISS) provide the data needed as inputs for the product updates National Oceanic and Atmospheric Administration (NOAA) provides to the public. SUVI is a full-disk extreme ultraviolet imager enabling Active Region characterization, filament eruption, and flare detection. EXIS provides inputs to solar back-ground-sevents impacting climate models. SEISS provides particle measurements over a wide energy-and-flux range that varies by several orders of magnitude and these data enable updates to spacecraft charge models for electrostatic discharge. EXIS and SEISS have been tested and calibrated end-to-end in ground test facilities around the United States. Due to the complexity of the SUVI design, data from component tests were used in a model to predict on-orbit performance. The ground tests and model updates provided inputs for designing the on-orbit calibration tests. A series of such tests have been planned for the Post-Launch Testing (PLT) of each of these instruments, and specific parameters have been identified that will be updated in the Ground Processing Algorithms, on-orbit parameter tables, or both. Some of SUVI and EXIS calibrations require slewing them off the Sun, while no such maneuvers are needed for SEISS. After a six-month PLT period the GOES-R is expected to be operational. The calibration details are presented in this paper.

  1. The development of a digital signal processing and plotting package to support testing of hazardous and radioactive material packages

    International Nuclear Information System (INIS)

    Ludwigsen, J.S.; Uncapher, W.L.; Arviso, M.; Lattier, C.N.; Hankinson, M.; Cannone, D.J.

    1995-01-01

    Federal regulations allow package designers to use analysis, testing, or a combination of analysis and testing to support certification of packages used to transport hazardous or radioactive materials. In recent years, many certified packages were subjected to a combination of analysis and testing. A major part of evaluating structural or thermal package response is the collection, reduction and presentation of instrumentation measurement data. Sandia National Laboratories, under the sponsorship of the US Department of Energy, has developed a comprehensive analysis and plotting package (known as KAPP) that performs digital signal processing of both transient structural and thermal data integrated with a comprehensive plotting package designed to support radioactive material package testing

  2. Integrated safeguards testing laboratories in support of the advanced fuel cycle initiative

    Energy Technology Data Exchange (ETDEWEB)

    Santi, Peter A [Los Alamos National Laboratory; Demuth, Scott F [Los Alamos National Laboratory; Klasky, Kristen L [Los Alamos National Laboratory; Lee, Haeok [Los Alamos National Laboratory; Miller, Michael C [Los Alamos National Laboratory; Sprinkle, James K [Los Alamos National Laboratory; Tobin, Stephen J [Los Alamos National Laboratory; Williams, Bradley [DOE, NE

    2009-01-01

    A key enabler for advanced fuel cycle safeguards research and technology development for programs such as the Advanced Fuel Cycle Initiative (AFCI) is access to facilities and nuclear materials. This access is necessary in many cases in order to ensure that advanced safeguards techniques and technologies meet the measurement needs for which they were designed. One such crucial facility is a hot cell based laboratory which would allow developers from universities, national laboratories, and commercial companies to perform iterative research and development of advanced safeguards instrumentation under realistic operating conditions but not be subject to production schedule limitations. The need for such a facility arises from the requirement to accurately measure minor actinide and/or fission product bearing nuclear materials that cannot be adequately shielded in glove boxes. With the contraction of the DOE nuclear complex following the end of the cold war, many suitable facilities at DOE sites are increasingly costly to operate and are being evaluated for closure. A hot cell based laboratory that allowed developers to install and remove instrumentation from the hot cell would allow for both risk mitigation and performance optimization of the instrumentation prior to fielding equipment in facilities where maintenance and repair of the instrumentation is difficult or impossible. These benefits are accomplished by providing developers the opportunity to iterate between testing the performance of the instrumentation by measuring realistic types and amounts of nuclear material, and adjusting and refining the instrumentation based on the results of these measurements. In this paper, we review the requirements for such a facility using the Wing 9 hot cells in the Los Alamos National Laboratory's Chemistry and Metallurgy Research facility as a model for such a facility and describe recent use of these hot cells in support of AFCI.

  3. Measuring Software Test Verification for Complex Workpieces based on Virtual Gear Measuring Instrument

    Science.gov (United States)

    Yin, Peili; Wang, Jianhua; Lu, Chunxia

    2017-08-01

    Validity and correctness test verification of the measuring software has been a thorny issue hindering the development of Gear Measuring Instrument (GMI). The main reason is that the software itself is difficult to separate from the rest of the measurement system for independent evaluation. This paper presents a Virtual Gear Measuring Instrument (VGMI) to independently validate the measuring software. The triangular patch model with accurately controlled precision was taken as the virtual workpiece and a universal collision detection model was established. The whole process simulation of workpiece measurement is implemented by VGMI replacing GMI and the measuring software is tested in the proposed virtual environment. Taking involute profile measurement procedure as an example, the validity of the software is evaluated based on the simulation results; meanwhile, experiments using the same measuring software are carried out on the involute master in a GMI. The experiment results indicate a consistency of tooth profile deviation and calibration results, thus verifying the accuracy of gear measuring system which includes the measurement procedures. It is shown that the VGMI presented can be applied in the validation of measuring software, providing a new ideal platform for testing of complex workpiece-measuring software without calibrated artifacts.

  4. Measuring Software Test Verification for Complex Workpieces based on Virtual Gear Measuring Instrument

    Directory of Open Access Journals (Sweden)

    Yin Peili

    2017-08-01

    Full Text Available Validity and correctness test verification of the measuring software has been a thorny issue hindering the development of Gear Measuring Instrument (GMI. The main reason is that the software itself is difficult to separate from the rest of the measurement system for independent evaluation. This paper presents a Virtual Gear Measuring Instrument (VGMI to independently validate the measuring software. The triangular patch model with accurately controlled precision was taken as the virtual workpiece and a universal collision detection model was established. The whole process simulation of workpiece measurement is implemented by VGMI replacing GMI and the measuring software is tested in the proposed virtual environment. Taking involute profile measurement procedure as an example, the validity of the software is evaluated based on the simulation results; meanwhile, experiments using the same measuring software are carried out on the involute master in a GMI. The experiment results indicate a consistency of tooth profile deviation and calibration results, thus verifying the accuracy of gear measuring system which includes the measurement procedures. It is shown that the VGMI presented can be applied in the validation of measuring software, providing a new ideal platform for testing of complex workpiece-measuring software without calibrated artifacts.

  5. Is It Working? Distractor Analysis Results from the Test Of Astronomy STandards (TOAST) Assessment Instrument

    Science.gov (United States)

    Slater, Stephanie

    2009-05-01

    The Test Of Astronomy STandards (TOAST) assessment instrument is a multiple-choice survey tightly aligned to the consensus learning goals stated by the American Astronomical Society - Chair's Conference on ASTRO 101, the American Association of the Advancement of Science's Project 2061 Benchmarks, and the National Research Council's National Science Education Standards. Researchers from the Cognition in Astronomy, Physics and Earth sciences Research (CAPER) Team at the University of Wyoming's Science and Math Teaching Center (UWYO SMTC) have been conducting a question-by-question distractor analysis procedure to determine the sensitivity and effectiveness of each item. In brief, the frequency each possible answer choice, known as a foil or distractor on a multiple-choice test, is determined and compared to the existing literature on the teaching and learning of astronomy. In addition to having statistical difficulty and discrimination values, a well functioning assessment item will show students selecting distractors in the relative proportions to how we expect them to respond based on known misconceptions and reasoning difficulties. In all cases, our distractor analysis suggests that all items are functioning as expected. These results add weight to the validity of the Test Of Astronomy STandards (TOAST) assessment instrument, which is designed to help instructors and researchers measure the impact of course-length duration instructional strategies for undergraduate science survey courses with learning goals tightly aligned to the consensus goals of the astronomy education community.

  6. Instrumentation of the thermal/structural interactions in situ tests at the Waste Isolation Pilot Plant (WIPP)

    Energy Technology Data Exchange (ETDEWEB)

    Munson, D.E. [Sandia National Labs., Albuquerque, NM (United States). Repository Isolation Systems Div.; Hoag, D.L.; Blankenship, D.A.; DeYonge, W.F.; Schiermeister, D.M. [RE/SPEC, Inc., Albuquerque, NM (United States); Jones, R.L.; Baird, G.T. [Tech Reps, Inc., Albuquerque, NM (United States)

    1997-04-01

    The Department of Energy has constructed the Waste Isolation Pilot Plant (WIPP) to develop the technology for the disposal of radioactive waste from defense programs. Sandia National Laboratories had the responsibility for the experimental activities at the WIPP and fielded several large-scale Thermal/Structural Interactions (TSI) in situ tests to validate techniques used to predict repository performance. The instrumentation of these tests involved the placement of over 4,200 gages including room closure gages, borehole extensometers, stress gages, borehole inclinometers, fixed reference gages, borehole strain gages, thermocouples, thermal flux meters, heater power gages, environmental gages, and ventilation gages. Most of the gages were remotely read instruments that were monitored by an automated data acquisition system, but manually read instruments were also used to provide early deformation information and to provide a redundancy of measurement for the remote gages. Instruments were selected that could operate in the harsh environment of the test rooms and that could accommodate the ranges of test room responses predicted by pretest calculations. Instruments were tested in the field prior to installation at the WIPP site and were modified to improve their performance. Other modifications were made to gages as the TSI tests progressed using knowledge gained from test maintenance. Quality assurance procedures were developed for all aspects of instrumentation including calibration, installation, and maintenance. The instrumentation performed exceptionally well and has produced a large quantity of quality information.

  7. Instrumentation of the thermal/structural interactions in situ tests at the Waste Isolation Pilot Plant (WIPP)

    International Nuclear Information System (INIS)

    Munson, D.E.; Jones, R.L.; Baird, G.T.

    1997-04-01

    The Department of Energy has constructed the Waste Isolation Pilot Plant (WIPP) to develop the technology for the disposal of radioactive waste from defense programs. Sandia National Laboratories had the responsibility for the experimental activities at the WIPP and fielded several large-scale Thermal/Structural Interactions (TSI) in situ tests to validate techniques used to predict repository performance. The instrumentation of these tests involved the placement of over 4,200 gages including room closure gages, borehole extensometers, stress gages, borehole inclinometers, fixed reference gages, borehole strain gages, thermocouples, thermal flux meters, heater power gages, environmental gages, and ventilation gages. Most of the gages were remotely read instruments that were monitored by an automated data acquisition system, but manually read instruments were also used to provide early deformation information and to provide a redundancy of measurement for the remote gages. Instruments were selected that could operate in the harsh environment of the test rooms and that could accommodate the ranges of test room responses predicted by pretest calculations. Instruments were tested in the field prior to installation at the WIPP site and were modified to improve their performance. Other modifications were made to gages as the TSI tests progressed using knowledge gained from test maintenance. Quality assurance procedures were developed for all aspects of instrumentation including calibration, installation, and maintenance. The instrumentation performed exceptionally well and has produced a large quantity of quality information

  8. The Grief Support in Healthcare Scale: development and testing.

    Science.gov (United States)

    Anderson, Keith A; Ewen, Heidi H; Miles, Elizabeth A

    2010-01-01

    Social support is an important factor to consider in understanding the grief process. However, existing measures of social support fail to account adequately for the unique characteristics of grief experienced by healthcare workers in relation to the deaths of patients or nursing home residents. The purposes of this study were to develop and to test a grief support measure specific to the experiences of healthcare workers. Using a cross-sectional design, 380 nursing assistants completed self-administered surveys focusing on grief and loss in the nursing home setting. Exploratory factor analysis and regression analysis were conducted to test the psychometric properties of the Grief Support in Healthcare Scale (GSHCS) and to investigate the scale's relationships with grief outcomes. Reflective of the theory of disenfranchised grief, the 15 items of the GSHCS were loaded onto three distinct factors: recognition of the relationship, acknowledgement of the loss, and inclusion of the griever. Reliability was acceptable to high across these factors (Cronbach's α of .89, .86, and .78, respectively). Regression analysis indicated that the three subscales of the GSHCS were related significantly to both distress from grief and growth from grief, yet these relationships were unique for each factor. This research demonstrated that the GSHCS has acceptable reliability and face validity for understanding grief in healthcare workers and may aid in the development of interventions targeted at enfranchising grief in this population. Additional testing is needed to estimate the validity and the reliability of the scale with other groups of healthcare workers.

  9. Knowledge Aid as Instrument of Regulation: World Bank's Non-Lending Higher Education Support for Ethiopia

    Science.gov (United States)

    Molla, Tebeje

    2014-01-01

    In the context of low-income countries, the role of donors in public policymaking is of great importance. Donors use a combination of lending and non-lending instruments as pathways of influence to shape policy directions in aid-recipient countries. This paper reports some findings from a doctoral study on the role of the World Bank in the recent…

  10. Standard test bench for calibrating instruments used to measure natural or artificial radioactive airborne particulates

    International Nuclear Information System (INIS)

    Charuau, J.; Grivaud, L.; Le Breton, M.

    1992-01-01

    An aerodynamic calibration device, known as ICARE, has been set up in France at the Saclay Research Centre to certify instruments used to measure natural or artificial airborne radioactive particulate contamination or radon. ICARE can calibrate passive detectors and monitors with sampling air flow-rates of less than 60 m 3 /h. The adjustment of such parameters as 222 Rn daughters volume activity, attached fraction and equilibrium factor, and the volume activity and size of α or β emitter carrying aerosols, allows realistic conditions to be obtained. ICARE complies with monitor test method standard currently under development by the International Electrotechnical Commission

  11. Instrumentation measurement and testing complex for detection and identification of radioactive materials using the emitted radiation

    International Nuclear Information System (INIS)

    Samossadny, V.T.; Dmitrenko, V.V.; Kadlin, V.V.; Kolesnikov, S.V.; Ulin, S.E.; Grachev, V.M.; Vlasik, K.F.; Dedenko, G.L.; Novikov, D.V.; Uteshev, Z.M.

    2006-01-01

    Simultaneous measurement of neutron and gamma radiation is a very usefull method for effective nuclear materials identification and control. The gamma-ray-neutron complex described in the paper is based on two multi-layer 3 He neutrons detectors and two High Pressure Xenon gamma-ray spectrometers assembled in one unit. All these detectors were callibrated on neutron and gamma-ray sources. The main characteristics of the instrumentation , its testing results and gamma-ray and neutron radiation parameters, which have been measured are represented in the paper. The gamma-neutron sources and fissile materials reliable detection and identification capability was demonstrated

  12. Response Time Analysis and Test of Protection System Instrument Channels for APR1400 and OPR1000

    International Nuclear Information System (INIS)

    Lee, Chang Jae; Han, Seung; Yun, Jae Hee; Baek, Seung Min; Lee, Sang Jeong

    2015-01-01

    Safety limits are required to maintain the integrity of physical barriers designed to prevent the uncontrolled release of radioactive materials in nuclear power plants. The safety analysis establishes two critical constraints that include an analytical limit in terms of a measured or calculated variable, and a specific time after the analytical limit is reached to begin protective action. Keeping with the nuclear regulations and industry standards, satisfying these two requirements will ensure that the safety limit will not be exceeded during the design basis event, either an anticipated operational occurrence or a postulated accident. Various studies on the setpoint determination methodology for the safety-related instrumentation have been actively performed to ensure that the requirement of the analytical limit is satisfied. In particular, the protection setpoint methodology for the advanced power reactor 1400 (APP1400) and the optimized power reactor 1000 (OPR1000) has been recently developed to cover both the design basis event and the beyond design basis event. The developed setpoint methodology has also been quantitatively validated using specific computer programs and setpoint calculations. However, the safety of nuclear power plants cannot be fully guaranteed by satisfying the requirement of the analytical limit. In spite of the response time verification requirements of nuclear regulations and industry standards, it is hard to find the studies on the systematically integrated methodology regarding the response time evaluation. In cases of APR1400 and OPR1000, the response time analysis for the plant protection system is partially included in the setpoint calculation and the response time test is separately performed via the specific plant procedure. The test technique has a drawback which is the difficulty to demonstrate completeness of timing test. The analysis technique has also a demerit of resulting in extreme times that not actually possible. Thus

  13. Historical and Theoretical Study of the Use of the Montessori Cylinder Block as a Screening Test Instrument for Developmental Disorders

    OpenAIRE

    我妻, 則明; AZUMA, Noriaki

    1994-01-01

    Studies investigating mental development screening tests and the Montessori cylinderblock were described. The theoretical possibility was discussed for the use of theMontessori cylinder block B type as a mental development screening test instrument.It was a theoretically unique idea to use the Montessori cylinder block B type as ascreening test instrument in measuring the child's mental development. As a result ofresearching previous studies, not only in Japan but also in other countries, the...

  14. Test Requirements and Conceptual Design for a Potassium Test Loop to Support an Advanced Potassium Rankine Cycle Power Conversion Systems

    Energy Technology Data Exchange (ETDEWEB)

    Yoder, JR.G.L.

    2006-03-08

    Parameters for continuing the design and specification of an experimental potassium test loop are identified in this report. Design and construction of a potassium test loop is part of the Phase II effort of the project ''Technology Development Program for an Advanced Potassium Rankine Power Conversion System''. This program is supported by the National Aeronautics and Space Administration. Design features for the potassium test loop and its instrumentation system, specific test articles, and engineered barriers for ensuring worker safety and protection of the environment are described along with safety and environmental protection requirements to be used during the design process. Information presented in the first portion of this report formed the basis to initiate the design phase of the program; however, the report is a living document that can be changed as necessary during the design process, reflecting modifications as additional design details are developed. Some portions of the report have parameters identified as ''to be determined'' (TBD), reflecting the early stage of the overall process. In cases where specific design values are presently unknown, the report attempts to document the quantities that remain to be defined in order to complete the design of the potassium test loop and supporting equipment.

  15. Nursing students' perception of academic support in the practicum: Development of a reliable and valid measurement instrument.

    Science.gov (United States)

    Arribas-Marín, Juan; Hernández-Franco, Vicente; Plumed-Moreno, Calixto

    The importance of practicum training in health sciences disciplines places prominence on the academic support received by students in this learning environment, both due to its leverage over their perceived level of satisfaction of academic proficiency as well as its impact on their academic performance. The aim of this study was to develop and validate a scale which facilitates the evaluation of academic support perceived by nursing students during their practicum. The sample is made up of 710 students from three academic levels of the Bachelor's Degree in Nursing. An instrument to evaluate the level of academic support perceived by the students was developed and validated. Subsequently, a measurement model of the dimensions which comprise the academic support in the practicum was created. The Academic Support in the Practicum Scale demonstrated high internal consistency, with a Cronbach's alpha value=0.913. The validation of the measurement instrument was carried out using confirmatory factor analysis and multi-sample analysis techniques, which presented positive goodness-of-fit indices. The developed tool has shown sufficient validity and high internal consistency. Its adequate psychometric properties lead to the conclusion that the scale provides a reliable and valid measurement of academic support perceived by students during their placement. Copyright © 2017 Elsevier Inc. All rights reserved.

  16. Translation and field testing of the family functioning, family health and social support questionnaire in Danish outpatients with heart failure

    DEFF Research Database (Denmark)

    Østergaard, Birte; Pedersen, Karen Steenvinkel; Lauridsen, Jørgen

    2018-01-01

    . The test-retest showed interclass correlation coefficients ranging between 0.69 and 0.86, indicating acceptable test-retest reliability. CONCLUSION: The Danish version of the FAFHES is an instrument that can be used to measure family functioning, family health and social support from the perspective......BACKGROUND: Valid and reliable instruments to assess family functioning, health and social support in families with heart failure constitute a cornerstone in the detection of the families' needs, in improving their functioning and in evaluating the effects of nursing interventions. AIM......: To translate the three scales of the Family Functioning, Family Health and Social Support (FAFHES) questionnaire from Finnish into Danish, to test validity and reliability of the Danish version among outpatients with heart failure and to add to previous studies by reconstructing scales using confirmatory...

  17. Power ramp tests of MOX fuel rods. HBWR irradiation with the instrument rig, IFA-591

    International Nuclear Information System (INIS)

    Ozawa, Takayuki; Abe, Tomoyuki

    2006-03-01

    Plutonium-uranium mixed oxide (MOX) fuel rods of instrumental rig IFA-591 were ramped in HBWR to study the Advanced Thermal Reactor (ATR) MOX fuel behavior during transient operation and to determine a failure threshold of the MOX fuel rods. Eleven segments were base-irradiated in ATR 'FUGEN' up to 18.4 GWd/t. Zirconium liner claddings were adopted for four segments of them. As the results of non-destructive post irradiation examinations (PIEs) after the base-irradiation and before the ramp tests, no remarkable behavior affecting the integrity of fuel assembly and fuel rod was confirmed. All segments to be used for the ramp tests, which consisted of the multi-step ramp tests and the single-step ramp tests, had instrumentations for in-pile measurements of cladding elongation or plenum pressure, and heated up to the maximum linear power of 58.3-68.4 kW/m without failure. The major results of ramp tests are as follows: There is no difference in PCMI behaviors between two type rods of Zry-2 and Zirconium liner claddings from the in-pile measurements of cladding elongation and plenum pressure. The computations of cladding elongation and inner pressure gave slightly lower elongation and pressure than the in-pile measurements during the ramp-test. However, the cladding relaxation during the power hold was in good agreement, and the fission gas release behavior during cooling down could be evaluated by taking into account the relaxation of contact pressure between pellet and cladding. Although the final power during IFA-591 ramp tests reached the higher linear power than the failure threshold power of UO 2 fuel rods, no indication of fuel failure was observed during the ramp tests. The cladding relaxation due to the creep deformation of the MOX pellets at high temperature could be confirmed at the power steps during the multi-ramp test. The fission gas release due to the emancipation from PCMI stress was observed during the power decreasing. The burn-up dependence could be

  18. The balanced scorecard as a potential instrument for supporting planning and improvement in accounting education: Comparative survey findings

    Directory of Open Access Journals (Sweden)

    CJ Cronje

    2004-04-01

    Full Text Available This paper is firstly a comparison of the components of a potential balanced scorecard for accounting departments of universities in South Africa and Australia. Secondly, the various suggested measurement criteria of the balanced scorecard components are also compared. The findings of the research paper indicate no significant differences. The conclusion is that the balanced scorecard constitutes a potential instrument for supporting the planning and improvement of the accounting education environment.

  19. Measuring relational and intrapersonal empowerment: testing instrument validity in a former soviet country with a secular muslim culture.

    Science.gov (United States)

    Cheryomukhin, Alexander; Peterson, N Andrew

    2014-06-01

    Research and evaluation studies measuring the construct of empowerment within international community development and human rights initiatives are rare due to a lack of validated measures appropriate for the cultural context. This study represents an initial effort to develop and test the Brief Azerbaijani Empowerment Scale (BAES), an instrument designed to assess relational and intrapersonal components of psychological empowerment among adult community residents (n = 350) in Azerbaijan, a former Soviet country with a predominantly Muslim culture. Exploratory factor analysis was used to examine the underlying dimensionality of the BAES, and path analysis was used to examine relationships between subscales of the BAES and a set of conceptually relevant variables (i.e., alienation, sense of community, and involvement in community organizations). Findings supported the reliability and validity of the BAES, which may be useful to future efforts to develop more comprehensive measures of intrapersonal and relational empowerment. Implications for future research and practice are discussed.

  20. Evaluation of a draft standard on performance specifications for health physics instrumentation. Initial results for radiological tests

    International Nuclear Information System (INIS)

    Swinth, K.L.; Kenoyer, J.L.; Mileham, A.P.; Kathren, R.L.; Selby, J.M.

    1983-06-01

    The draft ANSI standard N42.17D2 on performance specifications for health physics instrumentation is currently being evaluated by the Pacific Northwest Laboratory. The primary objective of the project is the evaluation of the applicability and practicality of the proposed standard through testing of a cross-section of currently available commercial instruments to determine how well they conform to the standard. The standard is being tested against instruments such as ionization chambers, G.M. detectors, alpha survey meters, and neutron dose equivalent survey meters. This paper presents results of the preliminary radiological performance tests on ionization chambers and G.M. detectors. This includes both the data generated during the tests and a discussion of procedures developed to perform the testing. Results are reported for response time, accuracy, precision, radiation overloads, and angular dependence. In addition, results are reported for parameters that affect instrument performance including battery lifetime, geotropism and stability. Initial test indicates that some of the instruments will not meet the criteria specified in ANSI N42.17D2. Results cover approximately 40 instruments that have been obtained by direct purchase, by loan from instrument vendors or by loan from others including DOE licensees

  1. Food-related lifestyles in Singapore: Preliminary testing of a Western European research instrument in Southeast Asia

    DEFF Research Database (Denmark)

    Askegaard, Søren; Brunsø, Karen

    1999-01-01

    , and to interpret similarities and differences found. For this purose, data have been collected in Singaporean families using the food-related life style instrument. A total of 89 questionnaires form the basis of the analysis. The cross-cultural validity of the instrument is tested and, in the light of those...... results, we interpret the results in relationship to local food cultures....

  2. Translation, validation, and reliability of the Dutch late-life function and disability instrument computer adaptive test

    NARCIS (Netherlands)

    Arensman, Remco M.; Pisters, Martijn F.; de Man-van Ginkel, Janneke M.; Schuurmans, Marieke J.; Jette, Alan M.; de Bie, Rob A.

    2016-01-01

    BACKGROUND: Adequate and user-friendly instruments for assessing physical function and disability in older adults are vital for estimating and predicting health care needs in clinical practice. The Late-Life Function and Disability Instrument Computer Adaptive Test (LLFDI-CAT) is a promising

  3. First Results from the Test Of Astronomy STandards (TOAST) Assessment Instrument

    Science.gov (United States)

    Slater, Stephanie

    2009-01-01

    Considerable effort in the astronomy education research over the past several years has focused on developing assessment tools in the form of multiple-choice conceptual diagnostics and content knowledge surveys. This has been critically important in advancing astronomy as a sub-discipline of physics education research, allowing researchers to establish the initial knowledge state of students as well as to attempt to measure some of the impacts of innovative instructional interventions. Before now, few of the existing instruments were constructed upon a solid list of clearly articulated and widely agreed upon learning objectives. Moving beyond the 10-year old Astronomy Diagnostics Test, we have developed and validated a new assessment instrument that is tightly aligned to the consensus learning goals stated by the American Astronomical Society - Chair's Conference on ASTRO 101, the American Association of the Advancement of Science's Project 2061 Benchmarks, and the National Research Council's National Science Education Standards. Researchers from the Cognition in Astronomy, Physics and Earth sciences Research (CAPER) Team at the University of Wyoming's Science and Math Teaching Center (UWYO SMTC) designed a criterion-referenced assessment tool, called the Test Of Astronomy STandards (TOAST). Through iterative development, this multiple-choice instrument has a high degree of reliability and validity for instructors and researchers needing information on students’ initial knowledge state at the beginning of a course and can be used, in aggregate, to help measure the impact of course-length duration instructional strategies for undergraduate science survey courses with learning goals tightly aligned to the consensus goals of the astronomy education community.

  4. Advanced Instrumentation, Information, and Control Systems Technologies Research in Support of Light Water Reactors

    International Nuclear Information System (INIS)

    Hallbert, Bruce P.; Kenneth, Thomas

    2014-01-01

    The Advanced Instrumentation, Information, and Control (II and C) Systems Technologies Pathway conducts targeted research and development (R and D) to address aging and reliability concerns with the legacy instrumentation and control and related information systems of the U.S. operating light water reactor (LWR) fleet. This work involves two major goals to ensure that legacy analog II and C systems are not life-limiting issues for the LWR fleet, and to implement digital II and C technology in a manner that enables broad innovation and business improvement in the nuclear power plant operating model. Resolving long-term operational concerns with the II and C systems contributes to the long-term sustainability of the LWR fleet, which is vital to the nation's energy and environmental security

  5. Advanced Instrumentation, Information, and Control Systems Technologies Research in Support of Light Water Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Hallbert, Bruce P.; Kenneth, Thomas [Idaho National Laboratory, Idaho (United States)

    2014-08-15

    The Advanced Instrumentation, Information, and Control (II and C) Systems Technologies Pathway conducts targeted research and development (R and D) to address aging and reliability concerns with the legacy instrumentation and control and related information systems of the U.S. operating light water reactor (LWR) fleet. This work involves two major goals to ensure that legacy analog II and C systems are not life-limiting issues for the LWR fleet, and to implement digital II and C technology in a manner that enables broad innovation and business improvement in the nuclear power plant operating model. Resolving long-term operational concerns with the II and C systems contributes to the long-term sustainability of the LWR fleet, which is vital to the nation's energy and environmental security.

  6. Design of springs in non-instrumented capsule for the HANARO irradiation test of advanced UO2 fuel

    International Nuclear Information System (INIS)

    Kim, D. H.; Lee, C. B.; Kang, H. S.

    2001-01-01

    Non-instrumented capsule was designed to irradiate the large grain UO 2 pellet developed for the high burn-up LWR fuel in the HANARO reactor. The non-instrumented capsule will be irradiated for about 30 months in HANARO Outside-core (OR) region. In the non-instrumented capsule, there are four different springs such as top guide spring, bottom spring, plenum spring and fuel rod hol-down spring. To ensure the mechanical integrity of non-instrumented capsule during the long term operation, those springs were designed after the spring characteristic tests

  7. An instrument for real time detection of contamination in space environmental tests chambers

    Science.gov (United States)

    Richmond, R. G.; Harmon, H. N.

    1972-01-01

    An instrument for in situ vacuum detection of surface reflectance changes at 1216A was designed. Using successive reflections, this instrument is more sensitive as an indicator of reflectance changes than similar instruments having only a single reflection. The selection of each component of the instrument and its operational performance is discussed.

  8. Instrumentation and data acquisition for full-scale aircraft crash testing

    Science.gov (United States)

    Jones, Lisa E.; Fasanella, Edwin L.

    1993-01-01

    The Landing and Impact Dynamics Branch of the NASA Langley Research Center has been conducting full-scale aircraft crash tests since the 1970s. Using a pendulum method, aircraft are suspended by cables from a 240-ft high gantry and swung into the impact surface at various attitudes and velocities. Instrumentation for these tests include on-board high-speed cameras, strain gages, load cells, displacement transducers, and accelerometers. Transducers in the aircraft are hard-wired through a long umbilical cable to the data acquisition room. Up to 96 channels of data can be collected at a typical rate of 4000 samples per second. Data acquisition using an FM multiplexed analog system and a high-speed personal computer based digital system is described.

  9. Testing for multigroup equivalence of a measuring instrument: a walk through the process.

    Science.gov (United States)

    Byrne, Barbara M

    2008-11-01

    This article presents an overview and application of the steps taken in testing for the equivalence of a measuring instrument across one or more groups. Following a basic description of, and rationale underlying these steps, the process is illustrated with data comprising response scores to four nonacademic subscales (Physical SC [Ability], Physical SC [Appearance], Social SC [Peers], and Social SC [Parents]) of the Self Description Questionnaire-I for Australian (N = 497) and Nigerian (N = 439) adolescents. All tests for validity and equivalence are based on the analysis of covariance structures within the framework of CFA models using the EQS 6 program. Prospective impediments to equivalence are suggested and additional caveats proposed in the special case where the groups under study represent different cultures.

  10. Greenhouse Gases in the South Atlantic: Testing and Automation of Instrumentation for Long-Term Monitoring

    Science.gov (United States)

    Lowry, D.; Fisher, R.; Sriskantharajah, S.; Lanoisellé, M.; Etchells, A.; Manning, A.; Nisbet, E.

    2009-04-01

    Understanding ocean uptake of atmospheric CO2 by the Southern Ocean is important for modelling of future global warming scenarios, particularly since it was recently proposed that this sink was reducing (Le Quéré, et al., 2007). To help our understanding of this problem a new project aims to flask sample air from 5 South Atlantic sites and set up continuous monitoring at the 2 most accessible of these: Ascension Island and the Falklands. Flask sample measurements will include CO2 and CH4 mixing ratios and the ^13C measurement of both of these gases using the rapid continuous flow trace gas analysis system at Royal Holloway, University of London (RHUL). Routine precisions are ±0.03 per mil and ±0.05 per mil for CO2 and CH4, respectively (Fisher et al., 2006). A time series of ^13C in CH4 was maintained for Ascension Island from 2000-2005 and a time series for methane isotopes commenced for the Falkland Islands in autumn 2007. To meet the continuous monitoring requirements of the new project, three Picarro G1301 CO2 / CH4 / H2O Cavity Ring Down Spectrometers (CRDS) were installed at RHUL in October 2008 for testing, calibration and the development of an automated air inlet system suitable for analysis of calibration gases at the remote sites. Initial testing included calibration with NOAA calibrated and target gases, validation of the Picarro-defined H2O-correction of CO2, and derivation of an H2O-correction for CH4. Continuing checks on the H2O correction are made by having 2 instruments side-by-side taking air from the same inlet, but one having a combined Nafion / Mg-perchlorate drying system that utilizes the analysis system exhaust gas for the reverse flow through the Nafion and maintains water-levels at 0.05% for more than 2 weeks. These instruments are connected to the same air inlet as a GC measuring CH4 mixing ratio and a LiCor 6252 measuring CO2 mixing ratio at 30-minute and 1-minute intervals respectively. The third CRDS instrument is connected to a

  11. Design and manufacturing of non-instrumented capsule for advanced PWR fuel pellet irradiation test in HANARO

    Energy Technology Data Exchange (ETDEWEB)

    Kim, D. H.; Lee, C. B.; Song, K. W. [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2002-04-01

    This project is preparing to irradiation test of the developed large grain UO{sub 2} fuel pellet in HANARO for pursuit fuel safety and high burn-up in 'Advanced LWR Fuel Technology Development Project' as a part Nuclear Mid and Long-term R and D Program. On the basis test rod is performed the nuclei property and preliminary fuel performance analysis, test rod and non-instrumented capsule are designed and manufactured for irradiation test in HANARO. This non-instrumented irradiation capsule of Advanced PWR Fuel pellet was referred the non-instrumented capsule for an irradiation test of simulated DUPIC fuel in HANARO(DUPIC Rig-001) and 18-element HANARO fuel, was designed to ensure the integrity and the endurance of non-instrumented capsule during the long term(2.5 years) irradiation. To irradiate the UO{sub 2} pellets up to the burn-up 70 MWD/kgU, need the time about 60 months and ensure the integrity of non-instrumented capsule for 30 months until replace the new capsule. This non-instrumented irradiation capsule will be based to develope the non-instrumented capsule for the more long term irradiation in HANARO. 22 refs., 13 figs., 5 tabs. (Author)

  12. Modeling safety instrumented systems with MooN voting architectures addressing system reconfiguration for testing

    International Nuclear Information System (INIS)

    Torres-Echeverria, A.C.; Martorell, S.; Thompson, H.A.

    2011-01-01

    This paper addresses the modeling of probability of dangerous failure on demand and spurious trip rate of safety instrumented systems that include MooN voting redundancies in their architecture. MooN systems are a special case of k-out-of-n systems. The first part of the article is devoted to the development of a time-dependent probability of dangerous failure on demand model with capability of handling MooN systems. The model is able to model explicitly common cause failure and diagnostic coverage, as well as different test frequencies and strategies. It includes quantification of both detected and undetected failures, and puts emphasis on the quantification of common cause failure to the system probability of dangerous failure on demand as an additional component. In order to be able to accommodate changes in testing strategies, special treatment is devoted to the analysis of system reconfiguration (including common cause failure) during test of one of its components, what is then included in the model. Another model for spurious trip rate is also analyzed and extended under the same methodology in order to empower it with similar capabilities. These two models are powerful enough, but at the same time simple, to be suitable for handling of dependability measures in multi-objective optimization of both system design and test strategies for safety instrumented systems. The level of modeling detail considered permits compliance with the requirements of the standard IEC 61508. The two models are applied to brief case studies to demonstrate their effectiveness. The results obtained demonstrated that the first model is adequate to quantify time-dependent PFD of MooN systems during different system states (i.e. full operation, test and repair) and different MooN configurations, which values are averaged to obtain the PFD avg . Also, it was demonstrated that the second model is adequate to quantify STR including spurious trips induced by internal component failure and

  13. A Unique Outside Neutron and Gamma Ray Instrumentation Development Test Facility at NASA's Goddard Space Flight Center

    Science.gov (United States)

    Bodnarik, J.; Evans, L.; Floyd, S.; Lim, L.; McClanahan, T.; Namkung, M.; Parsons, A.; Schweitzer, J.; Starr, R.; Trombka, J.

    2010-01-01

    An outside neutron and gamma ray instrumentation test facility has been constructed at NASA's Goddard Space Flight Center (GSFC) to evaluate conceptual designs of gamma ray and neutron systems that we intend to propose for future planetary lander and rover missions. We will describe this test facility and its current capabilities for operation of planetary in situ instrumentation, utilizing a l4 MeV pulsed neutron generator as the gamma ray excitation source with gamma ray and neutron detectors, in an open field with the ability to remotely monitor and operate experiments from a safe distance at an on-site building. The advantage of a permanent test facility with the ability to operate a neutron generator outside and the flexibility to modify testing configurations is essential for efficient testing of this type of technology. Until now, there have been no outdoor test facilities for realistically testing neutron and gamma ray instruments planned for solar system exploration

  14. Overload prevention in model supports for wind tunnel model testing

    Directory of Open Access Journals (Sweden)

    Anton IVANOVICI

    2015-09-01

    Full Text Available Preventing overloads in wind tunnel model supports is crucial to the integrity of the tested system. Results can only be interpreted as valid if the model support, conventionally called a sting remains sufficiently rigid during testing. Modeling and preliminary calculation can only give an estimate of the sting’s behavior under known forces and moments but sometimes unpredictable, aerodynamically caused model behavior can cause large transient overloads that cannot be taken into account at the sting design phase. To ensure model integrity and data validity an analog fast protection circuit was designed and tested. A post-factum analysis was carried out to optimize the overload detection and a short discussion on aeroelastic phenomena is included to show why such a detector has to be very fast. The last refinement of the concept consists in a fast detector coupled with a slightly slower one to differentiate between transient overloads that decay in time and those that are the result of aeroelastic unwanted phenomena. The decision to stop or continue the test is therefore conservatively taken preserving data and model integrity while allowing normal startup loads and transients to manifest.

  15. Testing of spatial ability: construction and evaluation of a new instrument

    Czech Academy of Sciences Publication Activity Database

    Květon, Petr; Jelínek, Martin; Vobořil, Dalibor

    2014-01-01

    Roč. 56, č. 3 (2014), s. 233-252 ISSN 0039-3320 R&D Projects: GA ČR(CZ) GAP407/11/2397 Institutional support: RVO:68081740 Keywords : spatial ability * testing * psychometrics Subject RIV: AN - Psychology Impact factor: 0.442, year: 2014

  16. Determination of the mechanical properties and fracture mechanisms of YSZ and GDC for electrolyte-supported SOFCs by instrumented indentation test; Determinacion de las propiedades mecanicas y mecanismos de fractura de electrolitos soportados de YSZ y GDC mediante ensayos de indentacion instrumentada

    Energy Technology Data Exchange (ETDEWEB)

    Roa, J. J.; Morales, M.; Capdevila, X. G.; Segarra, M.

    2010-07-01

    The main purpose of this work is to evaluate the different mechanical properties and the different fracture mechanisms activated during the instrumented indentation process of the electrolytes based on Yttria stabilized zirconia (YSZ) and gadolinia doped ceria (GDC), for solid oxide fuel cells (SOFCs). Both materials, with a thickness of 200 {mu}m, were shaped by uniaxial pressing at 500 MPa, and sintered at 1400 degree centigrade. Mechanical properties such as hardness (H) and Young's modulus (E) have been studied at different penetration depths using the Oliver and Pharr equations. The different fracture mechanisms activated during the instrumented indentation process have been studied at constant penetration depth of 500 nm, performed with a diamond Berkovich tip indenter. The residual indentation imprints have been observed with atomic force microscopy (AFM). The hardness and Young's modulus for YSZ electrolytes are higher than for GDC materials, due to the different fracture mechanism activated during the indentation process. As a result, the electrolytes of YSZ presented trans- and intergranular fracture mechanisms, depending on the place of the residual indentation imprint (in the grain boundary or in the middle of the grain, respectively). However, the GDC electrolyte revealed radical cracks at the corners of the residual nano indentation imprints, thus producing a phenomenon known as chipping. (Author)

  17. Spasticity after stroke: an overview of prevalence, test instruments, and treatments.

    Science.gov (United States)

    Sommerfeld, Disa K; Gripenstedt, Ullabritt; Welmer, Anna-Karin

    2012-09-01

    The objective of this study was to present an overview of the prevalence of spasticity after stroke as well as of test instruments and treatments. Recent studies show that spasticity occurs in 20%-30% of all stroke victims and in less than half of those with pareses. Although spasticity may occur in paretic patients after stroke, muscle weakness is more likely to be the reason for the pareses. Spasticity after stroke is more common in the upper than the lower limbs, and it seems to be more common among younger than older people. To determine the nature of passive stretch, electromyographic equipment is needed. However, the Modified Ashworth Scale, which measures the sum of the biomechanical and neural components in passive stretch, is the most common instrument used to grade spasticity after stroke. Treatment of spasticity with physiotherapy is recommended, although its beneficial effect is uncertain. The treatment of spasticity with botulinum toxin in combination with physiotherapy is suggested to improve functioning in patients with severe spasticity. A task-specific approach rather than a neurodevelopmental approach in assessing and treating a patient with spasticity after stroke seems to be preferred.

  18. Service quality in banking: developing and testing measurement instrument with Latvian sample data

    Directory of Open Access Journals (Sweden)

    Jelena Titko

    2013-01-01

    Full Text Available The paper highlights the importance of managing service quality in banking that can positively affect customer satisfaction. The goal of the given study is to develop an instrument for measuring service quality perceived by Latvian banks’ retail customers and to determine the most important contributors to customer satisfaction. To achieve this purpose, randomly selected customers of Latvian banks were surveyed, using the authors’ developed questionnaire. The proposed instrument was tested for reliability and validity, using techniques of confirmatory factor analysis. Exploratory factor analysis yielded five service quality dimensions (factors that allowed constructing customer satisfaction factor model EPICA: E – expenses, P – product, I – image, C – competence and emotional intellect, A – access. The subsequent correlation analysis revealed that the strongest relationship is between customer satisfaction and C factor. The results of the current research are crucially important for Latvian banks’ executives because the majority of previous studies in the related field offered measurement scales adequate for measuring service quality in other industries. Besides, the proposed questionnaire is exclusively developed for Latvia and considers Latvian banking sector specifics.

  19. Selected Standardized Tests and Assessment Instruments for Measuring Occupational Competencies. Teaching Basic Skills through Vocational Education. Technical Report.

    Science.gov (United States)

    Walker, Clinton B.

    Based on a review of standardized tests and competency assessment instruments, recommendations are made for identifying and selecting standardized tests to help secondary vocational instructors to develop students' basic skills. Chapter 1 focuses on identifying diagnostic tests of basic skills in reading, mathematics, and communication. It…

  20. Characterising the fracture toughness of polymers at moderately high rates of loading with the use of instrumented tensile impact testing

    NARCIS (Netherlands)

    Visser, Roy; Caimmi, F.; Pavan, A.

    2013-01-01

    The more common use of instrumentation in impact testing opened up the possibility to apply fracture mechanics testing methods to polymers at moderately high impact rates. Tensile impact testing offers some advantages over the more common three-point bending and compact tension geometries. Most

  1. Vibration testing and analysis of a multiply supported piping system

    International Nuclear Information System (INIS)

    Hsieh, B.J.; Kot, C.A.; Srinivasan, M.G.

    1987-01-01

    The behavior of nuclear power plant piping systems during earthquakes, and the most appropriate and economical mode of supporting such piping, is an issue of major concern. Consequently, the verification and validation of piping analysis methods and assumptions used in the design and safety assessment of nuclear power plants are of great interest. As part of its program on the validation of seismic calculational methods, the NR is specifically interested in the validation of the multiple support piping analysis module of the SMACS (Seismic Methodology Analysis Chain with Statistics) computer code. Data for comparing the dynamic behavior of various pipe hanger configurations and validating piping response analyses were recently obtained in the large shaker experiments (SHAG) conducted at the HDR. This paper describes preliminary results from the SHAG piping response tests and the approach taken in the validation of the SMACS code piping analysis. (orig./HP)

  2. Test-based approach to cable tray support system analysis and design: Behavior and test methods

    Energy Technology Data Exchange (ETDEWEB)

    Reigles, Damon G., E-mail: dreigles@engnovex.com [engNoveX, Inc., 19C Trolley Square, Wilmington, DE 19806 (United States); Brachmann, Ingo; Johnson, William H. [Bechtel Nuclear, Security & Environmental, 12011 Sunset Hills Rd, Suite 110, Reston, VA 20190 (United States); Gürbüz, Orhan [Tobolski Watkins Engineering, Inc., 4125 Sorrento Valley Blvd, Suite B, San Diego, CA 92121 (United States)

    2016-06-15

    Highlights: • Describes dynamic response behavior of unistrut type cable tray supports. • Summarizes observations from past full-scale shake table test programs. • Outlines testing methodologies necessary to identify key system parameters. - Abstract: Nuclear power plant safety-related cable tray support systems subjected to seismic loadings were originally understood and designed to behave as linear elastic systems. This behavioral paradigm persisted until the early 1980s when, due to evolution of regulatory criteria, some as-installed systems needed to be qualified to higher seismic motions than originally designed for. This requirement prompted a more in-depth consideration of the true seismic response behavior of support systems. Several utilities initiated extensive test programs, which demonstrated that trapeze strut-type cable tray support systems exhibited inelastic and nonlinear response behaviors with plastic hinging at the connections together with high damping due to bouncing of cables in the trays. These observations were used to demonstrate and justify the seismic adequacy of the aforementioned as-installed systems. However, no formalized design methodology or criteria were ever established to facilitate use of these test data for future evaluations. This paper assimilates and reviews the various test data and conclusions for the purpose of developing a design methodology for the seismic qualification of safety-related cable tray support systems.

  3. Performance test of the moisture separator reheaters (MSRs), Using the plant process instrumentation

    International Nuclear Information System (INIS)

    Casado Flores, E.; Bosh Aparicio, J.; Sanz Roman, J.

    1998-01-01

    A reliable test to determine the performance of the MSRs with a degree of reliability of 95% or more must follow the requirements of ASME PTC 12.4 1992. The plant process instrumentation is normally poorer than that required by the code not only in the number of measured parameters but also in accuracy. However, by means of some additional measurements, taken locally, and some appropriate operations, the behaviour of these important equipment items can be determined at the plant. Approximate values for the following parameters are obtained: a) Moisture separation efficiency b) Steam moisture at MSR outlet c) TTDs d) ΔP through the shell of the MSR e) Temperature of the reheated steam at the MSR outlet f) Excess steam flow. (Author)

  4. Mechanical properties of orthodontic wires derived by instrumented indentation testing (IIT) according to ISO 14577.

    Science.gov (United States)

    Zinelis, Spiros; Al Jabbari, Youssef S; Gaintantzopoulou, Marianna; Eliades, George; Eliades, Theodore

    2015-01-01

    The aim of this study was the characterization of mechanical properties of representative types of orthodontic wires employing instrumented indentation testing (IIT) according to ISO 14577. Segments were cut from ten wires. The first six are made of stainless steel (SS), two are made of Ni-Ti, and the last two are made of titanium molybdenum alloys (TMA). Then, the Martens hardness (HM), the Vickers hardness (HVIT) based on indentation hardness (H IT), the indentation modulus (E IT), the ratio of elastic to total work (η IT), and the traditional Vickers hardness (HV1) were measured by IIT. The results were statistically analyzed by one-way ANOVA followed by Student-Newman-Keuls (SNK) test at a = 0.05. The HVIT and HV1 data were analyzed by paired t test (a = 0.05). SS wires showed the highest hardness followed by TMA and Ni-Ti alloys. However, all wires showed significantly lower HVIT compared to corresponding HV1, a finding probably appended to elastic recovery around the indentation. E IT for all wires tested was determined much lower than the nominal values of the corresponding alloys due to the implication of residual stress field at the slope of unloading curve. Elastic to total work ratio was ranged from 45.8 to 64.4 % which is higher than that expected for ductile alloys (<30 %). The products tested illustrated significant differences in their mechanical properties. Although IIT provides reliable data for hardness and elastic index of materials tested, the intense residual stress field developed during the manufacturing process significantly affects the determination of modulus of elasticity.

  5. Shock sensitivity of diaminoazoxyfurazan (DAAF) using an instrumented small scale gap test

    Energy Technology Data Exchange (ETDEWEB)

    Francois, Elizabeth G [Los Alamos National Laboratory; Chavez, David E [Los Alamos National Laboratory; Mang, Joseph T [Los Alamos National Laboratory; Sanders, V Eric [Los Alamos National Laboratory; Lloyd, Joseph M [Los Alamos National Laboratory

    2009-01-01

    Diaminoazoxy furazan (DAAF) is an insensitive high explosive first synthesized in Russia in the 1980s and the synthesis path was developed at Los Alamos National Lab in the early 2000s. DAAF has safety characteristics (impact, friction) similar to TATB, but a critical diameter of less than 3mm and shock sensitivity similar to HMX. The combination of these characteristics is unusual and makes DAAF an interesting explosive that is suitable for booster applications. Gap testing is the ubiquitous test to statistically quantify shock sensitivity, but it exists in many forms. We used the LANL small scale gap test for our studies because it has the advantage of requiring very little material (less than 9g per test) and can be easily instrumented. While the gap test is statistical in nature, employing the Bruceton up-down method to determine a 50% point of detonation, we wanted to measure the shock velocity of the donor explosive into DAAF. To accomplish this, a series of shock wave experiments were conducted using representative gaps to capture the input pressure to the DAAF and to understand the shock pressure required for detonation. The experiments included in this paper investigated the effects of particle size on the shock sensitivity of DAAF. Three particle sizes (< 5{micro}m, 40{micro}m, and 80{micro}m) were tested at two densities (91% TMD and 97% TMD). The 80{micro}m particle size DAAF was obtained through the historic synthesis process, which also produces several energetic impurities. A novel synthesis process, which was developed at LANL over the past two years, produced DAAF with a 40 {micro}m particle size. Crash precipitating the 80 {micro}m DAAF in dimethyl sulfoxide, to render pure, yielded small (< 5 {micro}m) particle size DAAF. As expected the shock sensitivity is depressed by increasing density (decreasing porosity) and shows interesting trends with respect to particle size.

  6. How to Support Children with Mathematical Learning Disabilities Learning to Play an Instrument?

    Directory of Open Access Journals (Sweden)

    Annemie Desoete

    2012-01-01

    Full Text Available In this study, children with a mathematical learning disability (=14 and age-matched peers without learning disabilities (=14 as well as their parents and teachers were interviewed on how they experienced playing an instrument (guitar, drum, flute, violin, trombone, horn, and piano and on what helped them using a qualitative interactive interview with a flexible agenda to discover the interviewee’s own framework of meanings. Thematic analyses mentioned intrinsic motivation, extrinsic motivation, and self-efficacy as important. Some children with MLD were found to have a real musical talent and a very good musical ear and memory for sounds. However, all children with MLD seemed more dependent on the aid of parents, sibling, peers, and teachers. They had to study harder and needed more time to study, more practice, and a more structured approach.

  7. Fiscal instruments for the financial support of renewable in the Netherlands

    Energy Technology Data Exchange (ETDEWEB)

    Kwant, K.W.; Iepsma, J.; Pfeiffer, A.E. [Novem, Netherlands Agency for Energy and the Envionment, Utrecht (Netherlands)

    1997-08-01

    Green electricity is not a fiscal instrument, but rather a commercial way of selling renewable energy. Some utility providers start selling green electricity at a premium rate of about 4 cents above the normal price of 28.5 cents/kWhe. The additional sum is used to pay the producers of renewable electricity. In the Netherlands, the new green investment scheme became operational in January 1995. The idea is that private income from green investment, the dividend or interest on these specific green funds, should not be subject to income tax. This allows Green Funds to offer a lower interest rate to the public and thereby make the money available at a lower interest rate also to the green projects. (EG)

  8. On-line testing of calibration of process instrumentation channels in nuclear power plants. Phase 2, Final report

    Energy Technology Data Exchange (ETDEWEB)

    Hashemian, H.M. [Analysis and Measurement Services Corp., Knoxville, TN (United States)

    1995-11-01

    The nuclear industry is interested in automating the calibration of process instrumentation channels; this report provides key results of one of the sponsored projects to determine the validity of automated calibrations. Conclusion is that the normal outputs of instrument channels in nuclear plants can be monitored over a fuel cycle while the plant is operating to determine calibration drift in the field sensors and associated signal conversion and signal conditioning equipment. The procedure for on-line calibration tests involving calculating the deviation of each instrument channel from the best estimate of the process parameter that the instrument is measuring. Methods were evaluated for determining the best estimate. Deviation of each signal from the best estimate is updated frequently while the plant is operating and plotted vs time for entire fuel cycle, thereby providing time history plots that can reveal channel drift and other anomalies. Any instrument channel that exceeds allowable drift or channel accuracy band is then scheduled for calibration during a refueling outage or sooner. This provides calibration test results at the process operating point, one of the most critical points of the channel operation. This should suffice for most narrow-range instruments, although the calibration of some instruments can be verified at other points throughout their range. It should be pointed out that the calibration of some process signals such as the high pressure coolant injection flow in BWRs, which are normally off- scale during plant operation, can not be tested on-line.

  9. On-line testing of calibration of process instrumentation channels in nuclear power plants. Phase 2, Final report

    International Nuclear Information System (INIS)

    Hashemian, H.M.

    1995-11-01

    The nuclear industry is interested in automating the calibration of process instrumentation channels; this report provides key results of one of the sponsored projects to determine the validity of automated calibrations. Conclusion is that the normal outputs of instrument channels in nuclear plants can be monitored over a fuel cycle while the plant is operating to determine calibration drift in the field sensors and associated signal conversion and signal conditioning equipment. The procedure for on-line calibration tests involving calculating the deviation of each instrument channel from the best estimate of the process parameter that the instrument is measuring. Methods were evaluated for determining the best estimate. Deviation of each signal from the best estimate is updated frequently while the plant is operating and plotted vs time for entire fuel cycle, thereby providing time history plots that can reveal channel drift and other anomalies. Any instrument channel that exceeds allowable drift or channel accuracy band is then scheduled for calibration during a refueling outage or sooner. This provides calibration test results at the process operating point, one of the most critical points of the channel operation. This should suffice for most narrow-range instruments, although the calibration of some instruments can be verified at other points throughout their range. It should be pointed out that the calibration of some process signals such as the high pressure coolant injection flow in BWRs, which are normally off- scale during plant operation, can not be tested on-line

  10. The Listening Skills Test--a new instrument to assess children's pragmatic ability.

    Science.gov (United States)

    Lloyd, P; Peers, I; Foster, C

    2001-01-01

    Research has established that the development of autonomous (as opposed to collaborative) communication skills, using referential communication speaker and listener tasks, develops only slowly during the primary school years. Such a finding has implications for the classroom which puts a premium on independent language processing. Although the importance of oral language is recognised in the National Curriculum, there has been little attempt to assess the ability formally. The Listening Skills Test is a standardised pragmatic instrument focusing on the 3 1/2-7 years age group. The test is in four parts and assesses the ability to make judgements about the efficacy of verbal messages or instructions. Tasks include relating messages to arrays of pictorial items, making judgements about statements that refer to one complex picture, marking routes on a street plan in response to an extended set of instructions, and the ability to evaluate purely verbal utterances. The overall aim of the test is to assess children's ability to make sense on their own of verbal information in a decontextualised situation thought to represent the nature of much transactional communication in the classroom. Suggestions for remediation that have arisen from research conducted by the authors are also discussed.

  11. IN-PILE INSTRUMENTATION TO SUPPORT FUEL CYCLE RESEARCH AND DEVELOPMENT - FY12 STATUS REPORT

    Energy Technology Data Exchange (ETDEWEB)

    J. . Rempe; J. Daw; D. Knudson; R. Schley

    2012-09-01

    As part of the FCRD program objective to emphasize science-based, goal-oriented research, a strategic research program is underway to develop new sensors that can be used to obtain the high fidelity, real-time, data required for characterizing the performance of new fuels during irradiation testing. The overarching goal of this initiative is to develop new test vehicles with new sensors of unprecedented accuracy and resolution that can obtain the required data. Prior laboratory testing and, as needed, irradiation testing of sensors in these capsules will be completed as part of this initiative to give sufficient confidence that the irradiation tests will yield the required data. This report documents FY12 progress in this initiative.

  12. Auctions for Renewable Support in Denmark:Instruments and lessons learnt

    DEFF Research Database (Denmark)

    Kitzing, Lena; Wendring, Paul; Wigan, Fabian

    This report deals with all past and ongoing auctions for renewable support in Denmark. Since 2004, five single-item, technology-specific offshore wind auctions were held, with one more currently ongoing. One multi-item, multi-site nearshore wind auction is currently ongoing.......This report deals with all past and ongoing auctions for renewable support in Denmark. Since 2004, five single-item, technology-specific offshore wind auctions were held, with one more currently ongoing. One multi-item, multi-site nearshore wind auction is currently ongoing....

  13. Environmental Monitoring Plan, Nevada Test Site and support facilities

    International Nuclear Information System (INIS)

    1991-11-01

    This Environmental Monitoring Plan applies to the US Department of Energy's (DOE's) operations on the Continental US (including Amchitka Island, Alaska) that are under the purview of the DOE Nevada Field Office (DOE/NV). The primary purpose of these operations is the conduct of the nuclear weapons testing program for the DOE and the Department of Defense. Since 1951, these tests have been conducted principally at the Nevada Test Site (NTS), which is located approximately 100 miles northwest of Las Vegas, Nevada. In accordance with DOE Order 5400.1, this Environmental Monitoring Plan brings together in one document a description of the environmental activities conducted at the NTS by user organizations, operations support contractors, and the US Environmental Protection Agency (EPA). The EPA conducts both the offsite environmental monitoring program around the NTS and post-operational monitoring efforts at non-NTS test locations used between 1961 and 1973 in other parts of the continental US. All of these monitoring activities are conducted under the auspices of the DOE/NV, which has the stated policy of conducting its operations in compliance with both the letter and the spirit of applicable environmental statutes, regulations, and standards

  14. Laboratory testing and assessment of the Pickering PRD supporting frame

    International Nuclear Information System (INIS)

    Ghobarah, A.

    1995-05-01

    The objective of this study was to design and test reinforced concrete beam-column subassemblages representing the beam, column and joint of the Centre Pier (CP) support of the Pressure Relief Duct (PRD) at the Pickering A Nuclear Generating Station. The testing program was expected to establish the failure mode of the subassemblage and to compare the performance of the existing CP with a specimen detailed in accordance with current code provisions. A one-third scale specimen of the beam-column subassemblage was designed and tested to failure when subjected to simulated seismic loads. A second specimen was constructed with shear reinforcement that was detailed according to the provisions of the CAN3-N287.3-M82 code. The second specimen was tested in the same manner as the first specimen. From the experimental data on the behaviour and mode of failure of the specimens, analytical evaluations were conducted to determine the inelastic nonlinear behaviour of the CP structural system when subjected to various levels of ground motion. (author). 11 refs., 3 tabs., 40 figs

  15. LOFT test support branch data abstract report: one-sixth scale model BWR jet pump test

    International Nuclear Information System (INIS)

    Crapo, H.S.

    1979-01-01

    Pump performance data are presented for a 1/6 scale model jet pump in tests conducted at the LOFT Test Support Blowdown Facility. Steady-state subcooled pump characterization tests were performed over a wide range of forward and reverse flow conditions, both at room temperature, and at elevated temperature (555 0 K). Blowdown tests were also performed to obtain two-phase performance data in configurations simulating the flow patterns in the intact and broken loops of a BWR during a recirculation line break transient

  16. Vibration testing and analysis of a multiply supported piping system

    International Nuclear Information System (INIS)

    Hsieh, B.J.; Kot, C.A.; Srinivasan, M.G.

    1987-01-01

    The behavior of nuclear power plant piping systems during earthquake, and the most appropriate and economical mode of supporting such piping, is an issue of major concern. Consequently, the verification and validation of piping analysis methods and assumptions used in the design and safety assessment of nuclear power plants are of great interest. As part of its program on the validation of seismic calculational methods the US Nuclear Regulatory Commission (NRC) is specifically interested in the validation of the multiple support piping analysis module of the SMACS (Seismic Methodology Analysis Chain with Statistics) computer code. Data for the comparison of the dynamic behavior of various pipe hanger configurations and for the validation of piping response analyses were recently obtained in the large shaker experiments (SHAG) conducted at the HDR (Heissdampfreaktor) test facility in Kahl/Main, Federal Republic of Germany. This paper describes preliminary results from the SHAG piping response tests and the approach taken in the validation of the SMACS code piping analysis

  17. System support software for TSTA [Tritium Systems Test Assembly

    International Nuclear Information System (INIS)

    Claborn, G.W.; Mann, L.W.; Nielson, C.W.

    1987-10-01

    The fact that Tritium Systems Test Assembly (TSTA) is an experimental facility makes it impossible and undesirable to try to forecast the exact software requirements. Thus the software had to be written in a manner that would allow modifications without compromising the safety requirements imposed by the handling of tritium. This suggested a multi-level approach to the software. In this approach (much like the ISO network model) each level is isolated from the level below and above by cleanly defined interfaces. For example, the subsystem support level interfaces with the subsystem hardware through the software support level. Routines in the software support level provide operations like ''OPEN VALVE'' and CLOSE VALVE'' to the subsystem level. This isolates the subsystem level from the actual hardware. This is advantageous because changes can occur in any level without the need for propagating the change to any other level. The TSTA control system consists of the hardware level, the data conversion level, the operator interface level, and the subsystem process level. These levels are described

  18. Development and evaluation of a computerbased instrument supporting event analysis in NPP. Final report

    International Nuclear Information System (INIS)

    Szameitat, S.

    2002-11-01

    Information technologies (IT) in safety management are seen as opportunity to control and reduce risks. The processing of safety-critical event information, a central function of safety management, could be more efficient using computers. But organization structures are different, the processes of experience transfer are complex and the opportunities of IT are broad. To implement a support system is to question about design criteria of computer support for an event-based safety management system (eSMS). Two studies were conducted. Study 1 compares the organizational, technical and legal conditions for Safety Management in the German Nuclear Industry and the Norwegian Offshore Industry. It could identify design criteria, which independent from the operator influence the eSMS. Study 2 compares the eSMS of different nuclear power plants analyzing the organization structures and processes. Those internal and external criteria have a significant influence on a efficient design of a system support for eSMS. The third study makes the options and impact of computer support on experience transfer in eSMS as subject of discussion. For this purpose a simulation environment has been created. Groups investigated typical event scenarios from a nuclear power plant for contributing factors. The communication medium has been manipulated (face-to-face versus computer-mediated). Results of 15 groups indicate, that the collection of event information was promoted by computer-mediated communication. This is the foundation of the identification of contributing factors. The depth of analysis has not been influenced. Computer mediation hampers the learning of facts. IT can support safety management effectively. (orig.) [de

  19. Development and Psychometric Testing of the Diabetes Caregiver Activity and Support Scale.

    Science.gov (United States)

    Scarton, Lisa J; Bakas, Tamilyn; Miller, Wendy R; McLennon, Susan M; Huber, Lesa L; Hull, Margie A

    2017-10-01

    Purpose The purpose of this study was to develop and psychometrically test the Diabetes Caregiver Activity and Support Scale (D-CASS), a measure of how difficult or easy caregiver activity and supportive behaviors are for family caregivers of persons with type 2 diabetes (T2DM). Methods Internal consistency reliability, test-retest reliability, criterion-related validity, and construct validity were examined in 101 family caregivers of persons with T2DM. Participants were recruited using study brochures distributed at a large hospital in the Midwest and at statewide American Indian Pow Wows. Additionally, study brochures were available via a link on Facebook. Data collection occurred by telephone, face-to-face, or through Facebook using measures with evidence of reliability and validity. Family caregivers were predominately female (82.2%), spouses (50.2%), and American Indian (17%), African American (24%), or white (55%). Data were analyzed using descriptive statistics and psychometric analyses. Results The psychometric analyses resulted in an 11-item D-CASS with evidence of internal consistency reliability (alpha = .82) and test-retest reliability. Evidence of construct validity was obtained using 3 hierarchical multiple regressions guided by a conceptual model. Factor analysis supported the unidimensionality of the D-CASS. Conclusion The 11-item D-CASS is a brief and easy to administer instrument that has evidence of reliability and validity in family caregivers of persons with T2DM.

  20. Technology Roadmap Instrumentation, Control, and Human-Machine Interface to Support DOE Advanced Nuclear Energy Programs

    Energy Technology Data Exchange (ETDEWEB)

    Donald D Dudenhoeffer; Burce P Hallbert

    2007-03-01

    Instrumentation, Controls, and Human-Machine Interface (ICHMI) technologies are essential to ensuring delivery and effective operation of optimized advanced Generation IV (Gen IV) nuclear energy systems. In 1996, the Watts Bar I nuclear power plant in Tennessee was the last U.S. nuclear power plant to go on line. It was, in fact, built based on pre-1990 technology. Since this last U.S. nuclear power plant was designed, there have been major advances in the field of ICHMI systems. Computer technology employed in other industries has advanced dramatically, and computing systems are now replaced every few years as they become functionally obsolete. Functional obsolescence occurs when newer, more functional technology replaces or supersedes an existing technology, even though an existing technology may well be in working order.Although ICHMI architectures are comprised of much of the same technology, they have not been updated nearly as often in the nuclear power industry. For example, some newer Personal Digital Assistants (PDAs) or handheld computers may, in fact, have more functionality than the 1996 computer control system at the Watts Bar I plant. This illustrates the need to transition and upgrade current nuclear power plant ICHMI technologies.

  1. [Development and test-theoretical analysis of an instrument for data collection on patients' preferences and experiences concerning participation in nursing care decisions in acute hospitals].

    Science.gov (United States)

    Smoliner, Andrea; Hantikainen, Virpi; Mayer, Hanna; Ponocny-Seliger, Elisabeth; Them, Christa

    2009-12-01

    Patient orientation and patient participation are important aspects of modern health care and should be taken into consideration in the context of nursing care decision-making. The concept of evidence-based nursing also includes patient preferences in participation on decision-making, an area, however, which has not been adequately investigated so far. The aim of the present study was the development and testing of an instrument in German language for collecting data on patients' preferences and the experience of patients regarding their participation in nursing care decision-making in acute hospitals. The generation of items was based on available literature and in collaboration with specialists, using the theoretical model of Charles, Gafni and Whelan (1999). For testing the instrument, data was collected on 967 adult patients in surgical and medical wards of five hospitals in Vienna from October 2007 to March 2008. Test theoretical analyses included checking internal consistency, construct validity and criterion validity. The reliability of the scale preference and experience were confirmed by Cronbach's alpha (> or = 0.84) and the results of item analysis. The construct validity was supported by representing the decision model in the data. The criterion validity (concordant and discriminant validity) was tested with the two external criterions of subjective satisfaction with the information provided and decision making, and was supported by the results both at the level of total scores and at the level of item scores. In summary, the developed instrument represents an adequately reliable and valid test-theoretic, and also model-theoretic instrument for research in the field of evidence-based nursing. Therefore it is capable of gathering new knowledge on patients' preferences on participation in nursing care decision making.

  2. Instrumentation and control program to support modernization of safety and control in NPPs

    International Nuclear Information System (INIS)

    Wilkinson, D.; James, R.; Naser, J.; Torok, R.

    1997-01-01

    The original analog IandC equipment of most operating nuclear power plants requires increasing maintenance efforts to sustain system performance. Decreasing availability of replacement parts and support organizations for analog technology accentuate obsolescence problems and resultant OandM cost increases. Modern technology, especially digital systems, offers improved functionality, performance and reliability; solutions to obsolescence of equipment; reduction in OandM costs; and the potential to enhance safety. Digital systems with their inherent advantages will be implemented only if reliable and cost-effective implementation is achieved and if the upgraded system supports reduced power production costs. EPRI and its member utilities are working together under the Integrated IandC Upgrade Initiative to address IandC issues. The present paper describes and gives the status of EPRI's Integrated IandC Upgrade Initiative. (author)

  3. Realisation and instrumentation of high current power station for superconducting cables testing

    International Nuclear Information System (INIS)

    Regnaud, S.

    2000-05-01

    This report deals with the designing of a high current station able to test electric properties of superconductors. This test station will be used for testing the superconducting wires of large hadron collider detectors in CERN. The high current test station will have to generate high intensity continuous current in a magnetic field of 0 to 5 tesla and in temperature conditions of 4.2 K. The length of wire samples submitted to the uniform magnetic field is 300 mm and the installation is fitted with equipment able to measure the magnetic field perpendicular to either faces of the wire. The peculiarity of this station is to use a superconducting transformer in order to generate the high current. The first part of this work recalls important notions concerning superconductivity. The second part presents the high current station by describing the superconducting transformer and the sample-holder. We have studied the designing of a transformer able to yield a secondary current whose intensity reaches 100 kA, such intensity generates powerful electromagnetic forces (566 kN/m) in case of defect, so the sample-holder has to be carefully design to bear them. The third part presents the cryogenic component of the station, the instrumentation of the sample-holder and the method used to measure secondary currents. In the last part we present the performance of a prototype transformer, this prototype is able to deliver a 22 kA secondary current for a 160 A primary current, the uncertainty on the measured value of the secondary current is about 3%

  4. Structural Loading on the QCM/SAW Instrument Aboard the ER-2 Used for Atmospheric Testing

    Science.gov (United States)

    Bainum, Peter M.; Jones, Phyllis D.; Irish, Sandra M.; Xing, Guang-Qian

    1998-01-01

    Several experiments have been proposed to capture and evaluate samples of the atmosphere where SST's travel. One means to achieve this is to utilize the quartz crystal microbalance (QCM) / surface acoustical wave (SAW) instrument installed aboard the ER-2, formerly the U-2 reconnaissance aircraft. The QCM is a cascade impactor designed to perform in-situ, real-time measurements of aerosols and chemical vapors at an altitude of 60,000-70,000 feet. The primary use of the ER-2 is by NASA for Earth resources to test new sensor systems before being placed aboard satellites. One of the main reasons the ER-2 is used for this flight experiment is its capability to fly approximately twelve miles above the sea level (can reach an altitude of 78,000 feet). Because the ER-2 operates at such a high altitude, it is of special interest to scientists interested in space exploration or supersonic aircraft. The purpose of some of the experiments is to extinct data from the atmosphere around the ER-2. For the current CSTEA flight experiment, the housing of the QCM is in a frame that connects to an outer pod that attaches to the fuselage of the ER-2. Due to the location of the QCM within the housing frame and the location of the pod on the ER-2, the pod and its contents are subject to structural loads. In addition to structural loads, structural vibrations are also of importance because the QCM output data is based on the determination of beat frequencies between a pair of oscillators (one coated, the second uncoated, according to the chemical reaction being monitored). A structural analysis of this system can indicate whether potential resonances may exist between the (higher) structural modal frequencies and the beat frequencies. In addition undesirable deformations may result due to maximum expected static or dynamic loads during typical flight conditions. If the deformations are excessive they may adversely affect the accuracy the instrumentation output.

  5. ANALYZE THE KNOWLEDGE INQUIRY SCIENCE PHYSICS TEACHER CANDIDATES WITH ESSENCE INQUIRY SCIENCE TEST INSTRUMENT OPTIKA GEOMETRY

    Directory of Open Access Journals (Sweden)

    Wawan Bunawan

    2013-06-01

    Full Text Available The objective in this research to explore the relationship between ability of the knowledge essential features inquiry science and their reasons underlying sense of scientific inquiry for physics teacher candidates on content geometrical optics. The essential features of inquiry science are components that should arise during the learning process subject matter of geometrical optics reflectance of light on a flat mirror, the reflection of light on curved mirrors and refraction of light at the lens. Five of essential features inquiry science adopted from assessment system developed by the National Research Council. Content geometrical optics developed from an analysis of a college syllabus material. Based on the study of the essential features of inquiry and content develop the multiple choice diagnostic test three tier. Data were taken from the students who are taking courses in optics and wave from one the LPTK in North Sumatra totaled 38 students. Instruments showed Cronbach alpha reliability of 0.67 to test the essential features of inquiry science and 0.61 to there as on geometrical optics science inquiry.

  6. Generation of on-line test signals for nuclear instrumentation for PFBR

    International Nuclear Information System (INIS)

    Ram, Rajit; Bhatnagar, P.V.; Rajesh, M.G.; Das, Debashis

    2010-01-01

    Neutron flux monitoring system for PFBR employs pulse signal processing in start up and intermediate power range of reactor operation and Campbell signal processing in intermediate and full power range of reactor operation. Pulse signal processing unit as well as Campbell signal processing unit incorporates FPGA that generates pulse/white noise signal for on-line testing and diagnostic of the channels. In pulse channel fixed/linearly/exponentially varying pulse rate signal is generated over three decades of reactor operation. In the Campbell channel, Poisson distributed noise varying linearly/exponentially is generated over four decades of reactor operation. Multiple numbers of Poisson distributed random pulse trains are summed and amplified to get the white noise signal. Exponentially increasing gain pattern, generated by MATLAB is used to increase the RMS value of the generated noise. The paper discuses the successful testing and validation of pulse and Campbell channel by making use of the generated pulse/white noise signal over wide range of operation for nuclear instrumentation. (author)

  7. Re-fabrication and re-instrumentation of irradiated LWR fuel rods for irradiation testing at the HFR Petten

    International Nuclear Information System (INIS)

    Fischer, B.; Markgraf, J.F.W.; Puschek, P.; Duijves, K.A.; Haan, K.W. de

    1996-01-01

    LWR fuel testing at the High Flux Reactor (HFR) and the Hot Cells at Petten has been successfully performed with pre-irradiated fuel rod segments. The testing methods have been extended with hot cell techniques for re-fabrication of test fuel rods from full length fuel rods from power reactors; re-instrumentation of pre-irradiated fuel rod segments with pressure sensors; and instrumentation of re-fabricated fuel rods or fuel rod segments with central thermocouple and/or pressure sensors. 5 refs, 9 figs, 5 tabs

  8. Closure of Regenerative Life Support Systems: Results of the Lunar-Mars Life Support Test Project

    Science.gov (United States)

    Barta, Daniel; Henninger, D.; Edeen, M.; Lewis, J.; Smth, F.; Verostko, C.

    2006-01-01

    Future long duration human exploration missions away from Earth will require closed-loop regenerative life support systems to reduce launch mass, reduce dependency on resupply and increase the level of mission self sufficiency. Such systems may be based on the integration of biological and physiocochemical processes to produce potable water, breathable atmosphere and nutritious food from metabolic and other mission wastes. Over the period 1995 to 1998 a series of ground-based tests were conducted at the National Aeronautics and Space Administration, Johnson Space Center, to evaluate the performance of advanced closed-loop life support technologies with real human metabolic and hygiene loads. Named the Lunar-Mars Life Support Test Project (LMLSTP), four integrated human tests were conducted with increasing duration, complexity and closure. The first test, LMLSTP Phase I, was designed to demonstrate the ability of higher plants to revitalize cabin atmosphere. A single crew member spent 15 days within an atmospherically closed chamber containing 11.2 square meters of actively growing wheat. Atmospheric carbon dioxide and oxygen levels were maintained by control of the rate of photosynthesis through manipulation of light intensity or the availability of carbon dioxide and included integrated physicochemical systems. During the second and third tests, LMLSTP Phases II & IIa, four crew members spent 30 days and 60 days, respectively, in a larger sealed chamber. Advanced physicochemical life support hardware was used to regenerate the atmosphere and produce potable water from wastewater. Air revitalization was accomplished by using a molecular sieve and a Sabatier processor for carbon dioxide absorption and reduction, respectively, with oxygen generation performed by water hydrolysis. Production of potable water from wastewater included urine treatment (vapor compression distillation), primary treatment (ultrafiltration/reverse osmosis and multi-filtration) and post

  9. Development and Testing of Screen-Based and Psychometric Instruments for Assessing Resident Performance in an Operating Room Simulator

    Directory of Open Access Journals (Sweden)

    Richard R. McNeer

    2016-01-01

    Full Text Available Introduction. Medical simulators are used for assessing clinical skills and increasingly for testing hypotheses. We developed and tested an approach for assessing performance in anesthesia residents using screen-based simulation that ensures expert raters remain blinded to subject identity and experimental condition. Methods. Twenty anesthesia residents managed emergencies in an operating room simulator by logging actions through a custom graphical user interface. Two expert raters rated performance based on these entries using custom Global Rating Scale (GRS and Crisis Management Checklist (CMC instruments. Interrater reliability was measured by calculating intraclass correlation coefficients (ICC, and internal consistency of the instruments was assessed with Cronbach’s alpha. Agreement between GRS and CMC was measured using Spearman rank correlation (SRC. Results. Interrater agreement (GRS: ICC = 0.825, CMC: ICC = 0.878 and internal consistency (GRS: alpha = 0.838, CMC: alpha = 0.886 were good for both instruments. Subscale analysis indicated that several instrument items can be discarded. GRS and CMC scores were highly correlated (SRC = 0.948. Conclusions. In this pilot study, we demonstrated that screen-based simulation can allow blinded assessment of performance. GRS and CMC instruments demonstrated good rater agreement and internal consistency. We plan to further test construct validity of our instruments by measuring performance in our simulator as a function of training level.

  10. Environmental Monitoring Plan, Nevada Test Site and support facilities

    International Nuclear Information System (INIS)

    1991-11-01

    This Operational Area Monitoring Plan for environmental monitoring, is for EG ampersand G Energy Measurements, Inc. (EG ampersand G/EM) which operates several offsite facilities in support of activities at the Nevada Test Site (NTS). These facilities include: (1) Amador Valley Operations (AVO), Pleasanton, California; (2) Kirtland Operations (KO), Kirtland Air Force base, Albuquerque, New Mexico (KAFB); (3) Las Vegas Area Operations (LVAO), Remote Sensing Laboratory (RSL), and North Las Vegas (NLV) Complex at Nellis Air Force Base (NAFB), North Las Vegas, Nevada; (4) Los Alamos Operations (LAO), Los Alamos, New Mexico; (5) Santa Barbara Operations (SBO), Goleta, California; (6) Special Technologies Laboratory (STL), Santa Barbara, California; (7) Washington Aerial Measurements Department (WAMD), Andrews Air Force Base, Maryland; and, (8) Woburn Cathode Ray Tube Operations (WCO), Woburn, Massachusetts. Each of these facilities has an individual Operational Area Monitoring Plan, but they have been consolidated herein to reduce redundancy

  11. The Openness/Intellect Model on the M5-50: Supporting the Flexibility of IPIP-Based Instruments

    OpenAIRE

    Vuyk, M. Alexandra; University of Kansas; Ingram IV, Paul B.; University of Kansas; Multon, Karen D.; University of Kansas; Warlick, Craig A.; University of Kansas

    2016-01-01

    This study examined ways to improve fit and interpretive capacity of the M5-50, an IPIP-based personality instrument, using the Openness/Intellect model (O/I) given a history of poor performance of the M5-50 Openness scale (Author, 2013; Socha, Cooper, & McCord, 2010). With participants from Amazon’s MTurk (n = 305), theoretical models for the five-factor model, Openness as a 10-item single factor, and the O/I model were tested and fitted poorly After removing one problematic item, the O/I m...

  12. Development and preliminary testing of a self-rating instrument to measure self-directed learning ability of nursing students.

    Science.gov (United States)

    Cheng, Su-Fen; Kuo, Chien-Lin; Lin, Kuan-Chia; Lee-Hsieh, Jane

    2010-09-01

    With the growing trend of preparing students for lifelong learning, the theory of self-directed learning (SDL) has been increasingly applied in the context of higher education. In order to foster lifelong learning, abilities among nursing students, faculties need to have an appropriate instrument to measure the SDL abilities of nursing students. The objectives of this study were to develop an instrument to measure the SDL abilities of nursing students and to test the validity and reliability of this instrument. This study was conducted in 4 phases. In Phase 1, based on a review of the literature, the researchers developed an instrument to measure SDL. In Phase 2, two rounds of the Delphi study were conducted, to determine the content validity of the instrument. In Phase 3, a convenience sample of 1072 nursing students from two representative schools across three different types of nursing programs were recruited to test the construct validity of the Self-Directed Learning Instrument (SDLI). Finally, in Phase 4, the internal consistency and reliability of the instrument were tested. The resulting SDLI consists of 20 items across the following four domains: learning motivation, planning and implementing, self-monitoring, and interpersonal, communication. The final model in confirmatory factor analysis revealed that this 20-item SDLI indicated a good fit of the model. The value of Cronbach's alpha for the total scale was .916 and for the four domains were .801, .861, .785, and .765, respectively. The SDLI is a valid and reliable instrument for identifying student SDL abilities. It is available to students in nursing and similar medical programs to evaluate their own SDL. This scale may also enable nursing faculty to assess students' SDL status, design better lesson plans and curricula, and, implement appropriate teaching strategies for nursing students in order to foster the growth of lifelong learning abilities. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

  13. Adaptation and testing of psychosocial assessment instruments for cross-cultural use: an example from the Thailand Burma border.

    Science.gov (United States)

    Haroz, Emily E; Bass, Judith K; Lee, Catherine; Murray, Laura K; Robinson, Courtland; Bolton, Paul

    2014-01-01

    The purpose of this study was to develop valid and reliable instruments to assess priority psychosocial problems and functioning among adult survivors of systematic violence from Burma living in Thailand. The process involved four steps: 1) instrument drafting and piloting; 2) reliability and validity testing; 3) instrument revision; and 4) retesting revised instrument. A total of N = 158 interviews were completed. Overall subscales showed good internal consistency (0.73-0.92) and satisfactory combined test-retest/inter rater reliability (0.63-0.84). Criterion validity, was not demonstrated for any scale. The alcohol and functioning scales underperformed and were revised (step 3) and retested (step 4). Upon retesting, the function scale showed good internal consistency reliability (0.91-0.92), and the alcohol scale showed acceptable internal consistency (0.79) and strong test-retest/inter-rater reliability (0.86-0.89). This paper describes the importance and process of adaptation and testing, illustrated by the experiences and results for selected instruments in this population.

  14. Around the Table: Food Insecurity, Socioeconomic Status, and Instrumental Social Support among Women Living in a Rural Kenyan Island Community.

    Science.gov (United States)

    Nagata, Jason M; Fiorella, Kathryn J; Salmen, Charles R; Hickey, Matthew D; Mattah, Brian; Magerenge, Richard; Milner, Erin M; Weiser, Sheri D; Bukusi, Elizabeth A; Cohen, Craig R

    2015-01-01

    The objective of this study was to investigate the relationship among socioeconomic status, social support, and food insecurity in a rural Kenyan island community. A cross-sectional random sample of 111 female heads of households representing 583 household members were surveyed in Mfangano Island, Kenya from August to October 2010 using adaptations of the Household Food Insecurity Access Scale and the Medical Outcomes Study Social Support Survey. In multiple linear regression models, less instrumental social support, defined as concrete direct ways people help others (B = -0.81; 95% confidence interval [CI] -1.45 to -0.17), and decreased ownership scale based on owning material assets (B = -2.93; 95% CI -4.99 to -0.86) were significantly associated with increased food insecurity, controlling for age, education, marital status, and household size. Social support interventions geared at group capacity and resilience may be crucial adjuncts to improve and maintain the long term food security and health of persons living in low-resource regions.

  15. Data Collecting and Processing System and Hydraulic Control System of Hydraulic Support Model Test

    OpenAIRE

    Hong-Yu LIU; Jun-Qing LIU; Jun-Jie XI

    2014-01-01

    Hydraulic support is an important equipment of mechanization caving coal in modernization coal mine. Hydraulic support must pass national strength test before it quantity production and use. Hydraulic support model test based on similarity theory is a new effective hydraulic support design and test method. The test information such as displacement, stress, strain and so on can be generalized to hydraulic support prototype, which can prompt hydraulic support design. In order to satisfy the nee...

  16. Measuring the quality and quantity of professional intrapartum support: testing a computerised systematic observation tool in the clinical setting.

    Science.gov (United States)

    Ross-Davie, Mary C; Cheyne, Helen; Niven, Catherine

    2013-08-14

    Continuous support in labour has a significant impact on a range of clinical outcomes, though whether the quality and quantity of support behaviours affects the strength of this impact has not yet been established. To identify the quality and quantity of support, a reliable means of measurement is needed. To this end, a new computerised systematic observation tool, the 'SMILI' (Supportive Midwifery in Labour Instrument) was developed.The aim of the study was to test the validity and usability of the 'Supportive Midwifery in Labour Instrument' (SMILI) and to test the feasibility and acceptability of the systematic observation approach in the clinical intrapartum setting. Systematic observation was combined with a postnatal questionnaire and the collection of data about clinical processes and outcomes for each observed labour.The setting for the study was four National Health Service maternity units in Scotland, UK. Participants in this study were forty five midwives and forty four women.The SMILI was used by trained midwife observers to record labour care provided by midwives. Observations were undertaken for an average of two hours and seventeen minutes during the active first stage of labour and, in 18 cases, the observation included the second stage of labour. Content validity of the instrument was tested by the observers, noting the extent to which the SMILI facilitated the recording of all key aspects of labour care and interactions. Construct validity was tested through exploration of correlations between the data recorded and women's feelings about the support they received. Feasibility and usability data were recorded following each observation by the observer. Internal reliability and construct validity were tested through statistical analysis of the data. One hundred and four hours of labour care were observed and recorded using the SMILI during forty nine labour episodes. The SMILI was found to be a valid and reliable instrument in the intrapartum setting

  17. Mimicking Mars: a vacuum simulation chamber for testing environmental instrumentation for Mars exploration.

    Science.gov (United States)

    Sobrado, J M; Martín-Soler, J; Martín-Gago, J A

    2014-03-01

    We have built a Mars environmental simulation chamber, designed to test new electromechanical devices and instruments that could be used in space missions. We have developed this environmental system aiming at validating the meteorological station Rover Environment Monitoring Station of NASA's Mars Science Laboratory mission currently installed on Curiosity rover. The vacuum chamber has been built following a modular configuration and operates at pressures ranging from 1000 to 10(-6) mbars, and it is possible to control the gas composition (the atmosphere) within this pressure range. The device (or sample) under study can be irradiated by an ultraviolet source and its temperature can be controlled in the range from 108 to 423 K. As an important improvement with respect to other simulation chambers, the atmospheric gas into the experimental chamber is cooled at the walls by the use of liquid-nitrogen heat exchangers. This chamber incorporates a dust generation mechanism designed to study Martian-dust deposition while modifying the conditions of temperature, and UV irradiated.

  18. How Harmful are Survey Translations? A Test with Schwartz’s Human Values Instrument

    NARCIS (Netherlands)

    Davidov, E.; Beuckelaer, A. de

    2010-01-01

    One major challenge in international survey research is to ensure the equivalence of translated survey instruments across different cultures. In this study, we examine empirically the extent to which equivalence of survey instruments to measure human values can be established across cultures sharing

  19. Social And Legal Consequences Of I. Q. Tests As Classification Instruments: Some Warnings From Our Past

    Science.gov (United States)

    Kamin, Leon J.

    1975-01-01

    Social science instruments are not neutral. That school psychologists need to pay close attention to the sociopolitical implications of their assessment instruments is illustrated through the woeful history of the use and misuse of the concept of intelligence in the United States during the first third of this century. (Author)

  20. Sustainable expansion of electricity sector. Sustainability indicators as an instrument to support decision making

    Energy Technology Data Exchange (ETDEWEB)

    Rovere, Emilio Lebre La; Soares, Jeferson Borghetti; Oliveira, Luciano Basto; Lauria, Tatiana [Energy Planning Program (Coordination of Post Graduation Programs in Engineering at the Federal University of Rio de Janeiro), Centro de Tecnologia, Bloco C, Sala 211, Cidade Universitaria, Ilha do Fundao, Rio de Janeiro, CEP 21949-900 (Brazil)

    2010-01-15

    The aim of this paper is to put forward a proposal for a methodology to analyze the sustainability of the expansion of electricity generation. To do so, an approach is needed that takes into account, in an integrated perspective, the technical, socioeconomic, environmental and technological factors of the various alternatives for sector expansion. In this regard, multicriteria analysis (MCA) is proposed as an evaluation tool. It will be applied to a situation that involves the selection of the following expansion alternatives: small hydropowers, wind energy, generation from sugarcane bagasse, biodiesel, urban solid wastes, natural gas and nuclear energy. The methodology involved the development of indicators encompassing technological, environmental social and economic dimensions, for each of the aforementioned expansion alternatives, and the results were very interesting, from a multicriteria point of view, in their capacity to internalize socioenvironmental, technological and economic aspects in the decision making process for electricity generation expansion. It may well prove to be a useful tool for supporting this decision, although efforts are required to standardize the methodology with regard to its evaluation procedures. (author)

  1. Standard guide for evaluating performance characteristics of phased-Array ultrasonic testing instruments and systems

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2008-01-01

    1.1 This guide describes procedures for evaluating some performance characteristics of phased-array ultrasonic examination instruments and systems. 1.2 Evaluation of these characteristics is intended to be used for comparing instruments and systems or, by periodic repetition, for detecting long-term changes in the characteristics of a given instrument or system that may be indicative of impending failure, and which, if beyond certain limits, will require corrective maintenance. Instrument characteristics measured in accordance with this guide are expressed in terms that relate to their potential usefulness for ultrasonic examinations. Other electronic instrument characteristics in phased-array units are similar to non-phased-array units and may be measured as described in E 1065 or E 1324. 1.3 Ultrasonic examination systems using pulsed-wave trains and A-scan presentation (rf or video) may be evaluated. 1.4 This guide establishes no performance limits for examination systems; if such acceptance criteria ar...

  2. Moessbauer/XRF MIMOS Instrumentation and Operation During the 2012 Analog Field Test on Mauna Kea Volcano, Hawaii

    Science.gov (United States)

    Graff, Trevor G.; Morris, R. V.; Klingelhofer, G.; Blumers, M.

    2013-01-01

    Field testing and scientific investigations were conducted on the Mauna Kea Volcano, Hawaii, as part of the 2012 Moon and Mars Analog Mission Activities (MMAMA). Measurements were conducted using both stand-alone and rover-mounted instruments to determine the geophysical and geochemical properties of the field site, as well as provide operational constraints and science considerations for future robotic and human missions [1]. Reported here are the results from the two MIMOS instruments deployed as part of this planetary analog field test.

  3. Space Suit Portable Life Support System Test Bed (PLSS 1.0) Development and Testing

    Science.gov (United States)

    Watts, Carly; Campbell, Colin; Vogel, Matthew; Conger, Bruce

    2012-01-01

    A multi-year effort has been carried out at NASA-JSC to develop an advanced extra-vehicular activity Portable Life Support System (PLSS) design intended to further the current state of the art by increasing operational flexibility, reducing consumables, and increasing robustness. Previous efforts have focused on modeling and analyzing the advanced PLSS architecture, as well as developing key enabling technologies. Like the current International Space Station Extra-vehicular Mobility Unit PLSS, the advanced PLSS comprises three subsystems required to sustain the crew during extra-vehicular activity including the Thermal, Ventilation, and Oxygen Subsystems. This multi-year effort has culminated in the construction and operation of PLSS 1.0, a test bed that simulates full functionality of the advanced PLSS design. PLSS 1.0 integrates commercial off the shelf hardware with prototype technology development components, including the primary and secondary oxygen regulators, Ventilation Subsystem fan, Rapid Cycle Amine swingbed carbon dioxide and water vapor removal device, and Spacesuit Water Membrane Evaporator heat rejection device. The overall PLSS 1.0 test objective was to demonstrate the capability of the Advanced PLSS to provide key life support functions including suit pressure regulation, carbon dioxide and water vapor removal, thermal control and contingency purge operations. Supplying oxygen was not one of the specific life support functions because the PLSS 1.0 test was not oxygen rated. Nitrogen was used for the working gas. Additional test objectives were to confirm PLSS technology development components performance within an integrated test bed, identify unexpected system level interactions, and map the PLSS 1.0 performance with respect to key variables such as crewmember metabolic rate and suit pressure. Successful PLSS 1.0 testing completed 168 test points over 44 days of testing and produced a large database of test results that characterize system level

  4. Analyzing policy support instruments and regulatory risk factors for wind energy deployment-A developers' perspective

    International Nuclear Information System (INIS)

    Luethi, Sonja; Praessler, Thomas

    2011-01-01

    A transition to a renewable energy system is high on the policy agenda in many countries. A promising energy source for a low-carbon energy future is wind. Policy-makers can attract wind energy development by providing attractive policy frameworks. This paper argues that apart from the level of financial support, both the risks stemming from the regulatory environment (legal security, administrative process and grid access) and the ability to finance projects play a critical role in determining the attractiveness of the development environment. It sheds light on how project developers trade off these different aspects and to what extent the attractiveness of a certain policy framework increases with the introduction of specific measures. Conjoint analysis is employed to provide empirical evidence on the preference of wind energy developers in the EU and the US. The analysis shows that developers' preferences are very similar across the studied regions and for different types of developers. Which policy measures could be most valuable depends on the specific existing environment. In some southeastern European countries, a reduction of administrative process duration may yield the highest utility gains, whereas, in the US, improvements in grid access regulation and an increase in remuneration levels may be more effective. - Highlights: → Paper suggests conjoint analysis as scenario tool for estimating potential effects of specific policy measures. → It provides a quantitative, empirical dataset of 119 onshore wind energy developers' preferences. → Results suggest that the aspects 'Legal security' and 'Remuneration' are important attributes. → Cluster analyses yields slightly different preferences for developers from EU and US.

  5. Bench Test Model of the Human Skull for Testing the Variable Frequency Pulse Phase-Locked Loop Instrument

    National Research Council Canada - National Science Library

    Burin, Amy

    1996-01-01

    The Variable Frequency Pulse Phase-Locked Loop (VFPPLL) instrument is currently being used to non-invasively evaluate the human skull for increases in intracranial distances brought about by increases in intracranial pressure...

  6. The role of social support on HIV testing and treatment adherence: A qualitative study of HIV-infected refugees in southwestern Uganda.

    Science.gov (United States)

    Rouhani, Shada A; O'Laughlin, Kelli N; Faustin, Zikama M; Tsai, Alexander C; Kasozi, Julius; Ware, Norma C

    2017-08-01

    Little is known about the factors that encourage or discourage refugees to test for HIV, or to access and adhere to HIV care. In non-refugee populations, social support has been shown to influence HIV testing and utilisation of services. The present study enrolled HIV-infected refugees on anti-retroviral therapy (ART) in Uganda, who participated in qualitative interviews on HIV testing, treatment, and adherence. Interviews were analysed for themes about four types of social support: emotional, informational, instrumental, and appraisal support. A total of 61 interviews were analysed. Four roles for these types of social support were identified: (1) informational support encouraged refugees to test for HIV; (2) emotional support helped refugees cope with a diagnosis of HIV; (3) instrumental support facilitated adherence to ART and (4) after diagnosis, HIV-infected refugees provided informational and emotional support to encourage other refugees to test for HIV. These results suggest that social support influences HIV testing and treatment among refugees. Future interventions should capitalise on social support within a refugee settlement to facilitate testing and treatment.

  7. The individual supported living (ISL) manual: a planning and review instrument for individual supported living arrangements for adults with intellectual and developmental disabilities.

    Science.gov (United States)

    Cocks, E; Thoresen, S; Williamson, M; Boaden, R

    2014-07-01

    Following the closure of large residential facilities over the past several decades, emphasis on community living for adults with developmental disabilities has strengthened. However, the concept of community living is ambiguous. The term is often associated with congregation of people with disabilities in ordinary houses 'in' the community. Group homes, the most common contemporary formal expression of 'community living', may use ordinary houses and accommodate a small number of residents comparable to a large family. Individual supported living (ISL) arrangements around a single person with a disability using person-centred principles are occurring with increasing frequency. The ISL manual was developed over 4 years in two sequential research projects to produce a quality framework articulating ISL and operationalising the framework into a review and planning instrument for ISL arrangements. The ISL manual was developed in three stages and overseen by a reference group of key stakeholders purposively recruited as well-versed in ISL. The first stage operationalised the quality framework over two half-day workshops with a group of key informants. Participants identified indicators and sources of evidence for each attribute of the quality framework. The quality framework, indicators, and sources of evidence were compiled into an initial evaluation instrument of nine themes consisting of 27 attributes. This was piloted in two rounds to enhance the utility of the instrument and develop the final manual which contained eight themes and 21 attributes. A comprehensive literature search was carried out to identify relevant empirical ISL studies. The literature search identified four empirical studies that incorporated ISL over the preceding 3 years. A previous literature search from the first research project that produced the quality framework spanned 27 years and identified five empirical studies. We concluded that the empirical base for developing evidence for the

  8. Virtual Instrument Simulator for CERES

    Science.gov (United States)

    Chapman, John J.

    1997-01-01

    A benchtop virtual instrument simulator for CERES (Clouds and the Earth's Radiant Energy System) has been built at NASA, Langley Research Center in Hampton, VA. The CERES instruments will fly on several earth orbiting platforms notably NASDA's Tropical Rainfall Measurement Mission (TRMM) and NASA's Earth Observing System (EOS) satellites. CERES measures top of the atmosphere radiative fluxes using microprocessor controlled scanning radiometers. The CERES Virtual Instrument Simulator consists of electronic circuitry identical to the flight unit's twin microprocessors and telemetry interface to the supporting spacecraft electronics and two personal computers (PC) connected to the I/O ports that control azimuth and elevation gimbals. Software consists of the unmodified TRW developed Flight Code and Ground Support Software which serves as the instrument monitor and NASA/TRW developed engineering models of the scanners. The CERES Instrument Simulator will serve as a testbed for testing of custom instrument commands intended to solve in-flight anomalies of the instruments which could arise during the CERES mission. One of the supporting computers supports the telemetry display which monitors the simulator microprocessors during the development and testing of custom instrument commands. The CERES engineering development software models have been modified to provide a virtual instrument running on a second supporting computer linked in real time to the instrument flight microprocessor control ports. The CERES Instrument Simulator will be used to verify memory uploads by the CERES Flight Operations TEAM at NASA. Plots of the virtual scanner models match the actual instrument scan plots. A high speed logic analyzer has been used to track the performance of the flight microprocessor. The concept of using an identical but non-flight qualified microprocessor and electronics ensemble linked to a virtual instrument with identical system software affords a relatively inexpensive

  9. A study on the development of instrumented capsule for the material irradiation test

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Young Hwan; Park, J. M.; Choo, K. N.; Maeng, W. Y.; Park, D. K.; Oh, J. M.; Park, S. J.; Jung, S. H.; Park, J. S.; Kim, T. R.; Park, J. H.; Yang, S. Y.; Jun, Y. K.; Yang, S. H.

    1997-08-01

    Extensive efforts have been made to establish design and manufacturing technology for the instrumented capsule and its related system, which should be compatible with the HANARO`s characteristics. (author). 86 refs., 45 tabs., 146 figs.

  10. A New Instrument for Testing Wind Erosion by Soil Surface Shape Change

    Directory of Open Access Journals (Sweden)

    Chun-xing Hai

    2009-01-01

    Full Text Available Wind erosion, a primary cause of soil degeneration, is a problem in arid and semiarid areas throughout the world. Many methods are available to study soil erosion, but there is no an effective method for making quantitative measurements in the field. To solve this problem, we have developed a new instrument that can measure the change in the shape of the soil surface, allowing quick quantification of wind erosion. In this paper, the construction and principle of the new instrument are described. Field experiments are carried out using the instrument, and the data are analyzed. The erosion depth is found to vary by 11% compared to the average for measurement areas ranging from 30×30 cm2 to 10×10 cm2. The results show that the instrument is convenient and reliable for quantitatively measuring wind erosion in the field.

  11. Development of a word recognition instrument to test health literacy in dentistry: the REALD-30--a brief communication.

    Science.gov (United States)

    Lee, Jessica Y; Rozier, R Gary; Lee, Shoou-Yih Daniel; Bender, Deborah; Ruiz, Rafael E

    2007-01-01

    This study aims to develop and pilot test a dental word recognition instrument. The development of our instrument was based on the Rapid Estimate of Adult Literacy in Medicine (REALM), an efficient word recognition instrument used to assess health literacy in the medical arena. Our instrument, Rapid Estimate of Adult Literacy in Dentistry (REALD-30), consisted of 30 common dental words with various degrees of difficulty. It was administered to 202 English-speaking adults recruited from outpatient medical clinics. We examined the instrument's internal reliability using Cronbach's alpha and its validity by correlating the REALD-30 score to two dental outcomes (perceived dental health status and oral health-related quality of life) and medical health literacy. REALD-30 scores were significantly correlated with REALM scores. REALD-30 was significantly related to perceived dental health status in the bivariate analysis. It also was significantly related to oral health-related quality of life in a multivariate analysis. In contrast, medical health literacy was not related to either of the dental outcome measures. The new REALD-30 instrument displays good reliability but only partial validity. Results suggest that dental health literacy may be distinct from medical health literacy and may have an independent effect on dental health outcomes.

  12. Product analysis and initial reliability testing of the total mesorectal excision-quality assessment instrument.

    Science.gov (United States)

    Simunovic, Marko R; DeNardi, Franco G; Coates, Angela J; Szalay, David A; Eva, Kevin W

    2014-07-01

    Product analysis of rectal cancer resection specimens before specimen fixation may provide an immediate and relevant evaluation of surgical performance. We tested the interrater reliability (IRR) of a product analysis tool called the Total Mesorectal Excision-Quality Assessment Instrument (TME-QA). Participants included two gold standard raters, five pathology assistants, and eight pathologists. Domains of the TME-QA reflect total mesorectal excision principles including: (1) completeness of mesorectal margin; (2) completeness of mesorectum; (3) coning of distal mesorectum; (4) physical defects; and (5) overall specimen quality. Specimens were scored independently. We used the generalizability theory to assess the tool's internal consistency and IRR. There were 39 specimens and 120 ratings. Mean overall specimen quality scores for the gold standard raters, pathologists, and assistants were 4.43, 4.43, and 4.50, respectively (p > 0.85). IRR for the first nine items was 0.68 for the full sample, 0.62 for assistants alone, 0.63 for pathologists alone, and 0.74 for gold standard raters alone. IRR for the item overall specimen quality was 0.67 for the full sample, 0.45 for assistants, 0.80 for pathologists, and 0.86 for gold standard raters. IRR increased for all groups when scores were averaged across two raters. Assessment of surgical specimens using the TME-QA may provide rapid and relevant feedback to surgeons about their technical performance. Our results show good internal consistency and IRR when the TME-QA is used by pathologists. However, for pathology assistants, multiple ratings with the averaging of scores may be needed.

  13. Design, development, manufacturing, testing and commissioning of instrumentation for critical facility

    International Nuclear Information System (INIS)

    Dutta, P.K.; Gadgil, Kautubh; Punekar, Parag; Ramkumar, N.; Gohel, Nilesh; Darbhe, M.D.; Bharathan, R.; Bharadhwaj, G.

    2006-01-01

    The Critical Facility (CF) is a low power research reactor. Neutronic and Process Instrumentation are important systems those ensure safety and control of the reactor. The Control and Instrumentation systems for the Critical facility have been designed, developed and commissioned by RRMD. Most of the nuclear instrumentation used here is originally designed and developed jointly by Electronics Division and RRMD during ZAC project for conversion of the earlier vacuum tube based instrumentation to the solid state circuits during 1984-85 for Zerlina, Apsara and Cirus and are in operation at Cirus and Apsara since commissioning in 1984-85. The Process Instrumentation is provided for monitoring important process parameters such as level, flow, temperature and pressure and generating trips, alarms and interlocks necessary for smooth operation of the systems and safety of personnel and equipment. The paper will provide technical information on the reactor instrumentation for both nuclear and process systems, used in Critical Facility, the associated trip and alarms logics, and their integration into the reactor monitoring control and protection system, information systems developed for Critical Facility. (author)

  14. Empirical Testing of a Conceptual Model and Measurement Instrument for the Assessment of Trustworthiness of Project Team Members

    NARCIS (Netherlands)

    Rusman, Ellen; Van Bruggen, Jan; Valcke, Martin

    2009-01-01

    Rusman, E., Van Bruggen, J., & Valcke, M. (2009). Empirical Testing of a Conceptual Model and Measurement Instrument for the Assessment of Trustworthiness of Project Team Members. Paper presented at the Trust Workshop at the Eighth International Conference on Autonomous Agents and Multiagent Systems

  15. The 5-Dimensional Personality Test (5DPT): Relationships with Two Lexically Based Instruments and the Validation of the Absorption Scale

    NARCIS (Netherlands)

    van Kampen, D.

    2012-01-01

    Although intended to assess vulnerability factors associated with psychopathology, the 5-Dimensional Personality Test (5DPT) shows at least a superficial similarity to instruments that adhere to the lexical tradition in personality psychology. To investigate to which extent this similarity goes,

  16. Designing, Testing, and Validating an Attitudinal Survey on an Environmental Topic: A Groundwater Pollution Survey Instrument for Secondary School Students

    Science.gov (United States)

    Lacosta-Gabari, Idoya; Fernandez-Manzanal, Rosario; Sanchez-Gonzalez, Dolores

    2009-01-01

    Research in environmental attitudes' assessment has significantly increased in recent years. The development of specific attitude scales for specific environmental problems has often been proposed. This paper describes the Groundwater Pollution Test (GPT), a 19-item survey instrument using a Likert-type scale. The survey has been used with…

  17. Can we use social media to support content validity of patient-reported outcome instruments in medical product development?

    Science.gov (United States)

    Rothman, Margaret; Gnanaskathy, Ari; Wicks, Paul; Papadopoulos, Elektra J

    2015-01-01

    We report a panel designed to open a dialog between pharmaceutical sponsors, regulatory reviewers, and other stakeholders regarding the use of social media to collect data to support the content validity of patient-reported outcome instruments in the context of medical product labeling. Multiple stakeholder perspectives were brought together to better understand the issues encountered in pursuing social media as a form of data collection to support content validity. Presenters represented a pharmaceutical sponsor of clinical trials, a regulatory reviewer from the Food and Drug Administration, and an online data platform provider. Each presenter shared its perspective on the advantages and disadvantages of using social media to collect this type of information. There was consensus that there is great potential for using social media for this purpose. There remain, however, unanswered questions that need to be addressed such as identifying which type of social media is most appropriate for data collection and ensuring that participants are representative of the target population while maintaining the advantages of anonymity provided by online platforms. The use of social media to collect evidence of content validity holds much promise. Clarification of issues that need to be addressed and accumulation of empirical evidence to address these questions are essential to moving forward. Copyright © 2015 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier Inc. All rights reserved.

  18. Risk implications of renewable support instruments: Comparative analysis of feed-in tariffs and premiums using a mean-variance approach

    DEFF Research Database (Denmark)

    Kitzing, Lena

    2014-01-01

    Different support instruments for renewable energy expose investors differently to market risks. This has implications on the attractiveness of investment. We use mean-variance portfolio analysis to identify the risk implications of two support instruments: feed-in tariffs and feed-in premiums....... Using cash flow analysis, Monte Carlo simulations and mean-variance analysis, we quantify risk-return relationships for an exemplary offshore wind park in a simplified setting. We show that feedin tariffs systematically require lower direct support levels than feed-in premiums while providing the same...

  19. Engineering testing and technology projects FY 1996 Site Support Program Plan, WBS 6.3.3 and 6.3.8. Revision 1

    International Nuclear Information System (INIS)

    Brown, L.C.

    1995-10-01

    The engineering laboratory services for development, assembly, testing, and evaluation to support the resolution of WHC, Hanford, and DOE complex wide engineering issues for 1996 are presented. Primary customers are: TWRS, spent nuclear fuels, transition projects, liquid effluent program, and other Hanford contractors and programs. Products and services provided include: fabrication and assembly facilities for prototype and test equipment, development testing, proof of principle testing, instrumentation testing, nondestructive examination application development and testing, prototype equipment design and assembly, chemical engineering unit operations testing, engineering test system disposal, and safety issue resolution

  20. Distributed Unit Testing: supporting multiple platforms accurately and efficiently

    OpenAIRE

    García-Peñalvo, Francisco José; Santos, Pablo

    2006-01-01

    Testing is the most basic way to check the evolution of a software project. A strong test suite helps development team assuring that a certain minimum is always kept. Release after release software must pass a test group, large enough to check, at least, the most common use cases. Results will numerically show project s progress. Depending on the project testing could be done on different platforms under various operating systems. Forcing race conditions and heavy load is also a desired featu...

  1. A Novel Design of Needle Aspiration Biopsy Monitoring Instrument (NAOMI Tested on a Low Cost Chest Phantom

    Directory of Open Access Journals (Sweden)

    Surakusumah Rino Ferdian

    2016-01-01

    Full Text Available Needle biopsy is a medical intervention method for taking a lung tissue sample that suspected as a cancer. The disadvantage is the physicians directly visualize the anatomical structures in an open surgery for lung cancer biopsy procedure. There is a need to develop an instrument that may help the physician to guarantee the accuracy and efficiency while performing needle aspiration biopsy. Therefore, a needle aspiration biopsy monitoring instrument or named as NAOMI is proposed. It consists of a microcontroller system, an IMU sensor, an ultrasonic ranging module, a bluetooth module, and a 9V lithium battery. The experimental testing consist of performance testing, functional testing using chest phantom, and user acceptances. The results showed that the NAOMI improve the accuracy and efficiency while performing the needle biopsy operation.

  2. An Integrated Monitoring System Through 3d Laser Scanner and Traditional Instruments for Load Test on Arch Bridge

    Science.gov (United States)

    Pera, D.; Ferrando, I.

    2017-05-01

    The experimental campaign represents an example of how the careful design of the different test phases and the choice of the needed instrumentation are fundamental aspects to obtain a proper interpretation of the results, for future application on the real structures. Additionally, the present work represents a successful example of a combined monitoring system, integrating the traditional and innovative technical instrumentation for loading tests and geomatics survey techniques. The monitoring system has been designed with the aim of defining the load carrying capacity of a masonry arch bridge scaled model and to test the performances of a new retrofitting method. In particular, two different configuration have been considered: a first one with isolated arch and a second one with gravel fill on the arch.

  3. AN INTEGRATED MONITORING SYSTEM THROUGH 3D LASER SCANNER AND TRADITIONAL INSTRUMENTS FOR LOAD TEST ON ARCH BRIDGE

    Directory of Open Access Journals (Sweden)

    D. Pera

    2017-05-01

    Full Text Available The experimental campaign represents an example of how the careful design of the different test phases and the choice of the needed instrumentation are fundamental aspects to obtain a proper interpretation of the results, for future application on the real structures. Additionally, the present work represents a successful example of a combined monitoring system, integrating the traditional and innovative technical instrumentation for loading tests and geomatics survey techniques. The monitoring system has been designed with the aim of defining the load carrying capacity of a masonry arch bridge scaled model and to test the performances of a new retrofitting method. In particular, two different configuration have been considered: a first one with isolated arch and a second one with gravel fill on the arch.

  4. Eight Ways to Support Students during Standardized Tests. Classroom Tips

    Science.gov (United States)

    Higdon, Julie; Holcomb, Linda Laine

    2012-01-01

    Standardized testing time often creates a nervous atmosphere in classrooms. In past years one of the authors joined a chorus of teachers singing her own woes about the infamous test. She increased her daily caffeine intake, lost sleep, and became a nervous, crazed teacher who had turned her classroom into a test prep center. Her aha moment came…

  5. Simulation of laboratory tests of steel arch support

    Czech Academy of Sciences Publication Activity Database

    Horyl, P.; Šňupárek, Richard; Maršálek, P.; Pacześniowski, P.

    2017-01-01

    Roč. 62, č. 1 (2017), s. 163-176 ISSN 0860-7001 R&D Projects: GA MŠk ED1.1.00/02.0070; GA MŠk(CZ) LO1406; GA MŠk ED2.1.00/03.0082 Institutional support: RVO:68145535 Keywords : total load-bearing capacity * steel arch yielding support * rigid support * FEM Subject RIV: DH - Mining, incl. Coal Mining OBOR OECD: Mining and mineral processing Impact factor: 0.550, year: 2016 http://archiwum.img-pan.krakow.pl/index.php/AMS/article/view/952

  6. Space Suit Portable Life Support System (PLSS) 2.0 Unmanned Vacuum Environment Testing

    Science.gov (United States)

    Watts, Carly; Vogel, Matthew

    2016-01-01

    For the first time in more than 30 years, an advanced space suit Portable Life Support System (PLSS) design was operated inside a vacuum chamber representative of the flight operating environment. The test article, PLSS 2.0, was the second system-level integrated prototype of the advanced PLSS design, following the PLSS 1.0 Breadboard that was developed and tested throughout 2011. Whereas PLSS 1.0 included five technology development components with the balance the system simulated using commercial-off-the-shelf items, PLSS 2.0 featured first generation or later prototypes for all components less instrumentation, tubing and fittings. Developed throughout 2012, PLSS 2.0 was the first attempt to package the system into a flight-like representative volume. PLSS 2.0 testing included an extensive functional evaluation known as Pre-Installation Acceptance (PIA) testing, Human-in-the-Loop testing in which the PLSS 2.0 prototype was integrated via umbilicals to a manned prototype space suit for 19 two-hour simulated EVAs, and unmanned vacuum environment testing. Unmanned vacuum environment testing took place from 1/9/15-7/9/15 with PLSS 2.0 located inside a vacuum chamber. Test sequences included performance mapping of several components, carbon dioxide removal evaluations at simulated intravehicular activity (IVA) conditions, a regulator pressure schedule assessment, and culminated with 25 simulated extravehicular activities (EVAs). During the unmanned vacuum environment test series, PLSS 2.0 accumulated 378 hours of integrated testing including 291 hours of operation in a vacuum environment and 199 hours of simulated EVA time. The PLSS prototype performed nominally throughout the test series, with two notable exceptions including a pump failure and a Spacesuit Water Membrane Evaporator (SWME) leak, for which post-test failure investigations were performed. In addition to generating an extensive database of PLSS 2.0 performance data, achievements included requirements and

  7. Opportunities for mixed oxide fuel testing in the advanced test reactor to support plutonium disposition

    International Nuclear Information System (INIS)

    Terry, W.K.; Ryskamp, J.M.; Sterbentz, J.W.

    1995-08-01

    Numerous technical issues must be resolved before LWR operating licenses can be amended to allow the use of MOX fuel. These issues include the following: (1) MOX fuel fabrication process verification; (2) Whether and how to use burnable poisons to depress MOX fuel initial reactivity, which is higher than that of urania; (3) The effects of WGPu isotopic composition; (4) The feasibility of loading MOX fuel with plutonia content up to 7% by weight; (5) The effects of americium and gallium in WGPu; (6) Fission gas release from MOX fuel pellets made from WGPu; (7) Fuel/cladding gap closure; (8) The effects of power cycling and off-normal events on fuel integrity; (9) Development of radial distributions of burnup and fission products; (10) Power spiking near the interfaces of MOX and urania fuel assemblies; and (11) Fuel performance code validation. The Advanced Test Reactor (ATR) at the Idaho National Engineering Laboratory possesses many advantages for performing tests to resolve most of the issues identified above. We have performed calculations to show that the use of hafnium shrouds can produce spectrum adjustments that will bring the flux spectrum in ATR test loops into a good approximation to the spectrum anticipated in a commercial LWR containing MOX fuel while allowing operation of the test fuel assemblies near their optimum values of linear heat generation rate. The ATR would be a nearly ideal test bed for developing data needed to support applications to license LWRs for operation with MOX fuel made from weapons-grade plutonium. The requirements for planning and implementing a test program in the ATR have been identified. The facilities at Argonne National Laboratory-West can meet all potential needs for pre- and post-irradiation examination that might arise in a MOX fuel qualification program

  8. 'Test Driving' a Financing Instrument for Climate Adaptation : Analyzing Institutional Dilemmas using Simulation Gaming

    NARCIS (Netherlands)

    Root, Liz; van der Krabben, Erwin; Spit, T.J.M.

    2016-01-01

    Urban physical public infrastructure is a frontline defense mechanism to manage and mitigate climate-related impacts. Market instruments are often cited as possible means to spread risk and reduce financial burdens on the public sector. The authors argue that existing research tends to focus on the

  9. AGARD Flight Test Instrumentation Series. Volume 8. Linear and Angular Position Measurement of Aircraft Components

    Science.gov (United States)

    1977-01-01

    qynobro, inchesp I revolutions for one revolution of the comars synchro, where N in the ratio of the mechanical gear- Ing between the two qucbro dufts ...ratio is high - the shats have to make more turns. boently, now drive iutean for instruments- tion purpom have been introduced on the market . Two

  10. Use of a personal computer for instrumentation testing at the FFTF

    International Nuclear Information System (INIS)

    Clark, D.A.

    1985-01-01

    The FFTF uses computers to assist in performance of instrumentation calibration checks for Technical Specification compliance. When the computers used for these checks are not available, back-up methods must be used. A method of using a personal computer to serve as a back-up is discussed, and the hardware used is described

  11. 241-SY-101 DACS instrument problem screen (SCR 448) acceptance test procedure

    International Nuclear Information System (INIS)

    ERMI, A.M.

    1999-01-01

    The operability of the 241-SY-101 Data Acquisition and Control System (DACS) to provide proper control and monitoring of the mitigation mixer pump and instrumentation installed in the 241-SY-101 underground storage tank utilizing the [INSTPROB] screen will be systematically evaluated by the performance of this procedure

  12. Standard test method for verifying the alignment of X-Ray diffraction instrumentation for residual stress measurement

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2010-01-01

    1.1 This test method covers the preparation and use of a flat stress-free test specimen for the purpose of checking the systematic error caused by instrument misalignment or sample positioning in X-ray diffraction residual stress measurement, or both. 1.2 This test method is applicable to apparatus intended for X-ray diffraction macroscopic residual stress measurement in polycrystalline samples employing measurement of a diffraction peak position in the high-back reflection region, and in which the θ, 2θ, and ψ rotation axes can be made to coincide (see Fig. 1). 1.3 This test method describes the use of iron powder which has been investigated in round-robin studies for the purpose of verifying the alignment of instrumentation intended for stress measurement in ferritic or martensitic steels. To verify instrument alignment prior to stress measurement in other metallic alloys and ceramics, powder having the same or lower diffraction angle as the material to be measured should be prepared in similar fashion...

  13. Simulation of Laboratory Tests of Steel Arch Support

    Science.gov (United States)

    Horyl, Petr; Šňupárek, Richard; Maršálek, Pavel; Pacześniowski, Krzysztof

    2017-03-01

    The total load-bearing capacity of steel arch yielding roadways supports is among their most important characteristics. These values can be obtained in two ways: experimental measurements in a specialized laboratory or computer modelling by FEM. Experimental measurements are significantly more expensive and more time-consuming. However, for proper tuning, a computer model is very valuable and can provide the necessary verification by experiment. In the cooperating workplaces of GIG Katowice, VSB-Technical University of Ostrava and the Institute of Geonics ASCR this verification was successful. The present article discusses the conditions and results of this verification for static problems. The output is a tuned computer model, which may be used for other calculations to obtain the load-bearing capacity of other types of steel arch supports. Changes in other parameters such as the material properties of steel, size torques, friction coefficient values etc. can be determined relatively quickly by changing the properties of the investigated steel arch supports.

  14. Soil nitrate testing supports nitrogen management in irrigated annual crops

    Directory of Open Access Journals (Sweden)

    Patricia A. Lazicki

    2016-12-01

    Full Text Available Soil nitrate (NO3− tests are an integral part of nutrient management in annual crops. They help growers make field-specific nitrogen (N fertilization decisions, use N more efficiently and, if necessary, comply with California's Irrigated Lands Regulatory Program, which requires an N management plan and an estimate of soil NO3− from most growers. As NO3− is easily leached into deeper soil layers and groundwater by rain and excess irrigation water, precipitation and irrigation schedules need to be taken into account when sampling soil and interpreting test results. We reviewed current knowledge on best practices for taking and using soil NO3− tests in California irrigated annual crops, including how sampling for soil NO3− differs from sampling for other nutrients, how tests performed at different times of the year are interpreted and some of the special challenges associated with NO3− testing in organic systems.

  15. Geo-portal as a planning instrument: supporting decision making and fostering market potential of Energy efficiency in buildings

    Science.gov (United States)

    Cuca, Branka; Brumana, Raffaella; Oreni, Daniela; Iannaccone, Giuliana; Sesana, Marta Maria

    2014-03-01

    Steady technological progress has led to a noticeable advancement in disciplines associated with Earth observation. This has enabled information transition regarding changing scenarios, both natural and urban, to occur in (almost) real time. In particular, the need for integration on a local scale with the wider territorial framework has occurred in analysis and monitoring of built environments over the last few decades. The progress of Geographic Information (GI) science has provided significant advancements when it comes to spatial analysis, while the almost free availability of the internet has ensured a fast and constant exchange of geo-information, even for everyday users' requirements. Due to its descriptive and semantic nature, geo-spatial information is capable of providing a complete overview of a certain phenomenon and of predicting the implications within the natural, social and economic context. However, in order to integrate geospatial data into decision making processes, it is necessary to provide a specific context, which is well supported by verified data. This paper investigates the potentials of geo-portals as planning instruments developed to share multi-temporal/multi-scale spatial data, responding to specific end-users' demands in the case of Energy efficiency in Buildings (EeB) across European countries. The case study regards the GeoCluster geo-portal and mapping tool (Project GE2O, FP7), built upon a GeoClustering methodology for mapping of indicators relevant for energy efficiency technologies in the construction sector.

  16. Development of a Culture Specific Critical Thinking Ability Test and Using It as a Supportive Diagnostic Test for Giftedness

    Science.gov (United States)

    Köksal, Mustafa Serdar

    2016-01-01

    The purposes of this study were to develop a culture specific critical thinking ability test for 6, 7, and 8. grade students in Turkey and to use it as an assessment instrument for giftedness. For these purposes, item pool involving 22 items was formed by writing items focusing on the current and common events presented in (Turkish) media from…

  17. Final Report: Part 1. In-Place Filter Testing Instrument for Nuclear Material Containers. Part 2. Canister Filter Test Standards for Aerosol Capture Rates.

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Austin Douglas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Runnels, Joel T. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Moore, Murray E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Reeves, Kirk Patrick [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2014-11-02

    A portable instrument has been developed to assess the functionality of filter sand o-rings on nuclear material storage canisters, without requiring removal of the canister lid. Additionally, a set of fifteen filter standards were procured for verifying aerosol leakage and pressure drop measurements in the Los Alamos Filter Test System. The US Department of Energy uses several thousand canisters for storing nuclear material in different chemical and physical forms. Specialized filters are installed into canister lids to allow gases to escape, and to maintain an internal ambient pressure while containing radioactive contaminants. Diagnosing the condition of container filters and canister integrity is important to ensure worker and public safety and for determining the handling requirements of legacy apparatus. This report describes the In-Place-Filter-Tester, the Instrument Development Plan and the Instrument Operating Method that were developed at the Los Alamos National Laboratory to determine the “as found” condition of unopened storage canisters. The Instrument Operating Method provides instructions for future evaluations of as-found canisters packaged with nuclear material. Customized stainless steel canister interfaces were developed for pressure-port access and to apply a suction clamping force for the interface. These are compatible with selected Hagan-style and SAVY-4000 storage canisters that were purchased from NFT (Nuclear Filter Technology, Golden, CO). Two instruments were developed for this effort: an initial Los Alamos POC (Proof-of-Concept) unit and the final Los Alamos IPFT system. The Los Alamos POC was used to create the Instrument Development Plan: (1) to determine the air flow and pressure characteristics associated with canister filter clogging, and (2) to test simulated configurations that mimicked canister leakage paths. The canister leakage scenarios included quantifying: (A) air leakage due to foreign material (i.e. dust and hair

  18. Rover-Based Instrumentation and Scientific Investigations During the 2012 Analog Field Test on Mauna Kea Volcano, Hawaii

    Science.gov (United States)

    Graham, L. D.; Graff, T. G.

    2013-01-01

    Rover-based 2012 Moon and Mars Analog Mission Activities (MMAMA) were recently completed on Mauna Kea Volcano, Hawaii. Scientific investigations, scientific input, and operational constraints were tested in the context of existing project and protocols for the field activities designed to help NASA achieve the Vision for Space Exploration [1]. Several investigations were conducted by the rover mounted instruments to determine key geophysical and geochemical properties of the site, as well as capture the geological context of the area and the samples investigated. The rover traverse and associated science investigations were conducted over a three day period on the southeast flank of the Mauna Kea Volcano, Hawaii. The test area was at an elevation of 11,500 feet and is known as "Apollo Valley" (Fig. 1). Here we report the integration and operation of the rover-mounted instruments, as well as the scientific investigations that were conducted.

  19. Instrument Control (iC) - An Open-Source Software to Automate Test Equipment.

    Science.gov (United States)

    Pernstich, K P

    2012-01-01

    It has become common practice to automate data acquisition from programmable instrumentation, and a range of different software solutions fulfill this task. Many routine measurements require sequential processing of certain tasks, for instance to adjust the temperature of a sample stage, take a measurement, and repeat that cycle for other temperatures. This paper introduces an open-source Java program that processes a series of text-based commands that define the measurement sequence. These commands are in an intuitive format which provides great flexibility and allows quick and easy adaptation to various measurement needs. For each of these commands, the iC-framework calls a corresponding Java method that addresses the specified instrument to perform the desired task. The functionality of iC can be extended with minimal programming effort in Java or Python, and new measurement equipment can be addressed by defining new commands in a text file without any programming.

  20. Test and Delivery of the Chemin Mineralogical Instrument for Mars Science Laboratory

    Science.gov (United States)

    Blake, D. F.; Vaniman, D.; Anderson, R.; Bish, D.; Chipera, S.; Chemtob, S.; Crisp, J.; DesMarais, D. J.; Downs, R.; Feldman, S.; hide

    2010-01-01

    The CheMin mineralogical instrument on MSL will return quantitative powder X-ray diffraction data (XRD) and qualitative X-ray fluorescence data (XRF; 14

  1. Survey Instrument Development for Consumer Perception Testing to RTE Product in Convenience Store

    Directory of Open Access Journals (Sweden)

    Dyah Lestari Widaningrum

    2015-09-01

    Full Text Available Global trade and the abolition of trade barriers lead to the proliferation of imported food products such as various types of fast food products (RTE: ready-to-eat food sold by convenience stores mainly scattered in Jakarta. The question is what causes consumers choose certain convenience store to buy RTE Product and not choose another outlet category. To understand consumer perceptions, it is necessary to develop an instrument for measuring consumer perceptions of the option to purchase RTE Product at convenience stores. Variables used in this research are the perception and knowledge of the public/consumers against food safety, store attributes, service, and product attributes. The instrument used in this study is a questionnaire with a scalemeasuring1-5 to see the relationship between variables, we used the method of Structural Equation Modeling (SEM. The sample used in this study was 223 respondents that were divided into five areas in Jakarta, namely Central Jakarta, West Jakarta, South Jakarta, East Jakarta, and North Jakarta. The final outcome of the instrument development process was 25 observed variables, consisting of 4 indicators, which valid and reliable, with T-values for each observed variable is above 2,58, and Construct Reliability values range between 0,76 to 0,853.

  2. Received social support and exercising: An intervention study to test the enabling hypothesis.

    Science.gov (United States)

    Rackow, Pamela; Scholz, Urte; Hornung, Rainer

    2015-11-01

    Received social support is considered important for health-enhancing exercise participation. The enabling hypothesis of social support suggests an indirect association of social support and exercising via constructs of self-regulation, such as self-efficacy. This study aimed at examining an expanded enabling hypothesis by examining effects of different kinds of social support (i.e., emotional and instrumental) on exercising not only via self-efficacy but also via self-monitoring and action planning. An 8-week online study was conducted. Participants were randomly assigned to an intervention or a control group. The intervention comprised finding and then exercising regularly with a new exercise companion. Intervention and control group effects were compared by a manifest multigroup model. Received emotional social support predicted self-efficacy, self-monitoring, and action planning in the intervention group. Moreover, received emotional social support was indirectly connected with exercise via the examined mediators. The indirect effect from received emotional social support via self-efficacy mainly contributed to the total effect. No direct or indirect effect of received instrumental social support on exercise emerged. In the control group, neither emotional nor instrumental social support was associated with any of the self-regulation constructs nor with exercise. Actively looking for a new exercise companion and exercising together seems to be beneficial for the promotion of received emotional and instrumental social support. Emotional support in turn promotes exercise by enabling better self-regulation, in particular self-efficacy. Statement of contribution What is already known on this subject? With the 'enabling hypothesis', Benight and Bandura (2004, Behav. Res. Ther., 42, 1129) claimed that social support indirectly affects behaviour via self-efficacy. Research in the domain of physical exercise has provided evidence for this enabling hypothesis on a

  3. Anticipating the friction coefficient of friction materials used in automobiles by means of machine learning without using a test instrument

    OpenAIRE

    TİMUR, Mustafa; AYDIN, Fatih

    2013-01-01

    The most important factor for designs in which friction materials are used is the coefficient of friction. The coefficient of friction has been determined taking such variants as velocity, temperature, and pressure into account, which arise from various factors in friction materials, and by analyzing the effects of these variants on friction materials. Many test instruments have been produced in order to determine the coefficient of friction. In this article, a study about the use ...

  4. Charpy impact test results on five materials and NIST verification specimens using instrumented 2-mm and 8-mm strikers

    International Nuclear Information System (INIS)

    Nanstad, R.K.; Sokolov, M.A.

    1995-01-01

    The Heavy-Section Steel Irradiation Program at Oak Ridge National Laboratory is involved in two cooperative projects, with international participants, both of which involve Charpy V-notch impact tests with instrumented strikers of 2mm and 8mm radii. Two heats of A 533 grade B class I pressure vessel steel and a low upper-shelf (LUS) submerged-arc (SA) weld were tested on the same Charpy machine, while one heat of a Russian Cr-Mo-V forging steel and a high upper-shelf (HUS) SA weld were tested on two different machines. The number of replicate tests at any one temperature ranged from 2 to 46 specimens. Prior to testing with each striker, verification specimens at the low, high, and super high energy levels from the National Institute of Standards and Technology (NIST) were tested. In the two series of verification tests, the tests with the 2mm striker met the requirements at the low and high energy levels but not at the super high energy. For one plate, the 2mm striker showed somewhat higher average absorbed energies than those for the 8-mm striker at all three test temperatures. For the second plate and the LUS weld, however, the 2mm striker showed somewhat lower energies at both test temperatures. For the Russian forging steel and the HUS weld, tests were conducted over a range of temperatures with tests at one laboratory using the 8mm striker and tests at a second laboratory using the 2mm striker. Lateral expansion was measured for all specimens and the results are compared with the absorbed energy results. The overall results showed generally good agreement (within one standard deviation) in energy measurements by the two strikers. Load-time traces from the instrumented strikers were also compared and used to estimate shear fracture percentage. Four different formulas from the European Structural Integrity Society draft standard for instrumented Charpy test are compared and a new formula is proposed for estimation of percent shear from the force-time trace

  5. Cryomdoule Test Stand Reduced-Magnetic Support Design at Fermilab

    Energy Technology Data Exchange (ETDEWEB)

    McGee, Mike [Fermilab; Chandrasekaran, Saravan Kumar [Fermilab; Crawford, Anthony [Fermilab; Harms, Elvin [Fermilab; Leibfritz, Jerry [Fermilab; Wu, Genfa [Fermilab

    2016-06-01

    In a partnership with SLAC National Accelerator Laboratory (SLAC) and Jefferson Lab, Fermilab will assemble and test 17 of the 35 total 1.3 GHz cryomodules for the Linac Coherent Light Source II (LCLS-II) Project. These devices will be tested at Fermilab's Cryomodule Test Facility (CMTF) within the Cryomodule Test Stand (CMTS-1) cave. The problem of magnetic pollution became one of major issues during design stage of the LCLS-II cryomodule as the average quality factor of the accelerating cavities is specified to be 2.7 x 10¹⁰. One of the possible ways to mitigate the effect of stray magnetic fields and to keep it below the goal of 5 mGauss involves the application of low permeable materials. Initial permeability and magnetic measurement studies regarding the use of 316L stainless steel material indicated that cold work (machining) and heat affected zones from welding would be acceptable.

  6. SLAC FASTBUS Snoop Module: test results and support software

    International Nuclear Information System (INIS)

    Gustavson, D.B.; Walz, H.V.

    1985-09-01

    The development of a diagnostic module for FASTBUS has been completed. The Snoop Module is designed to reside on a Crate Segment and provide high-speed diagnostic monitoring and testing capabilities. Final hardware details and testing of production prototype modules are reported. Features of software under development for a stand-alone single Snoop diagnostic system and Multi-Snoop networks will be discussed. 3 refs., 2 figs

  7. Mixed oxide fuels testing in the advanced test reactor to support plutonium disposition

    International Nuclear Information System (INIS)

    Ryskamp, J.M.; Sterbentz, J.W.; Chang, G.S.

    1995-09-01

    An intense worldwide effort is now under way to find means of reducing the stockpile of weapons-grade plutonium. One of the most attractive solutions would be to use WGPu as fuel in existing light water reactors (LWRs) in the form of mixed oxide (MOX) fuel - i.e., plutonia (PUO 2 ) mixed with urania (UO 2 ). Before U.S. reactors could be used for this purpose, their operating licenses would have to be amended. Numerous technical issues must be resolved before LWR operating licenses can be amended to allow the use of MOX fuel. These issues include the following: (1) MOX fuel fabrication process verification, (2) Whether and how to use burnable poisons to depress MOX fuel initial reactivity, which is higher than that of urania, (3) The effects of WGPu isotopic composition, (4) The feasibility of loading MOX fuel with plutonia content up to 7% by weight, (5) The effects of americium and gallium in WGPu, (6) Fission gas release from MOX fuel pellets made from WGPu, (7) Fuel/cladding gap closure, (8) The effects of power cycling and off-normal events on fuel integrity, (9) Development of radial distributions of burnup and fission products, (10) Power spiking near the interfaces of MOX and urania fuel assemblies, and (11) Fuel performance code validation. We have performed calculations to show that the use of hafnium shrouds can produce spectrum adjustments that will bring the flux spectrum in ATR test loops into a good approximation to the spectrum anticipated in a commercial LWR containing MOX fuel while allowing operation of the test fuel assemblies near their optimum values of linear heat generation rate. The ATR would be a nearly ideal test bed for developing data needed to support applications to license LWRs for operation with MOX fuel made from weapons-grade plutonium. The requirements for planning and implementing a test program in the ATR have been identified

  8. Design and Testing of a Controller for the Martian Atmosphere Pressure and Humidity Instrument DREAMS-P/H

    Science.gov (United States)

    Tapani Nikkanen, Timo; Schmidt, Walter; Genzer, Maria; Harri, Ari-Matti; Haukka, Harri

    2013-04-01

    The European Space Agency (ESA), driven by the goal of performing a soft landing on Mars, is planning to launch the Entry, descent and landing Demonstrator Module (EDM)[1] simultaneously with the Trace Gas Orbiter (TGO) as a part of the ExoMars program towards Mars in 2016. As a secondary objective, the EDM will gather meteorological data and observe the electrical environment of the landing site with its Dust characterisation, Risk assessment, and Environmental Analyser on the Martian Surface (DREAMS). The Finnish Meteorological Institute (FMI) is participating in the project by designing, building and testing a pressure and a humidity instrument for Mars, named DREAMS-P and DREAMS-H, respectively. The instruments are based on previous FMI designs, including ones flown on board the Huygens, Phoenix and Mars Science Laboratory.[2] Traditionally, the FMI pressure and humidity instruments have been controlled by an FPGA. However, the need to incorporate more autonomy and modifiability into instruments, cut the development time and component costs, stimulated interest to study a Commercial Off-The-Shelf (COTS) Microcontroller Unit (MCU) based instrument design. Thus, in the DREAMS-P/H design, an automotive MCU is used as the instrument controller. The MCU has been qualified for space by tests in and outside FMI. The DREAMS-P/H controller command and data interface utilizes a RS-422 connection to receive telecommands from and to transmit data to the Central Electronics Unit (CEU) of the DREAMS science package. The two pressure transducers of DREAMS-P and one humidity transducer of DREAMS-H are controlled by a single MCU. The MCU controls the power flow for each transducer and performs pulse counting measurements on sensor and reference channels to retrieve scientific data. Pressure and humidity measurements are scheduled and set up according to a configuration table assigned to each transducer. The configuration tables can be modified during the flight. The whole

  9. Some Hardware and Instrumentation Aspects of the Development of an Automation System for Jar Tests in Drinking Water Treatment.

    Science.gov (United States)

    Calderón, Antonio José; González, Isaías

    2017-10-11

    The so-called Jar Test (JT) plays a vital role in the drinking water and wastewater treatments for establishing the dosage of flocculants and coagulant. This test is a well-proved laboratory instrumental procedure performed by trained personnel. In this work, a completely novel system for the automation and monitoring of a JT devoted to drinking water treatment is presented. It has been implemented using an industrial programmable controller and sensors and instruments specifically selected for this purpose. Once the parameters of the test have been entered, the stages that compose the JT (stirring, coagulant addition, etc.) are sequentially performed without human intervention. Moreover, all the involved measurements from sensors are collected and made accessible for continuous monitoring of the process. By means of the proposed system, the JT procedure is conducted fully automatically and can be locally and remotely monitored in real-time. Furthermore, the developed system constitutes a portable laboratory that offers advantageous features like scalability and transportability. The proposed system is described focusing on hardware and instrumentation aspects, and successful results are reported.

  10. Autonomy support, need satisfaction, and motivation for support among adults with intellectual disability : Testing a self-determination theory model

    NARCIS (Netherlands)

    Frielink, Noud; Schuengel, Carlo; Embregts, Petri J.C.M.

    2018-01-01

    The tenets of self-determination theory as applied to support were tested with structural equation modelling for 186 people with ID with a mild to borderline level of functioning. The results showed that (a) perceived autonomy support was positively associated with autonomous motivation and with

  11. Autonomy Support, Need Satisfaction, and Motivation for Support among Adults with Intellectual Disability: Testing a Self-Determination Theory Model

    Science.gov (United States)

    Frielink, Noud; Schuengel, Carlo; Embregts, Petri J. C. M.

    2018-01-01

    The tenets of self-determination theory as applied to support were tested with structural equation modelling for 186 people with ID with a mild to borderline level of functioning. The results showed that (a) perceived autonomy support was positively associated with autonomous motivation and with satisfaction of need for autonomy, relatedness, and…

  12. Thermal-hydraulic tests of steam-generator tube-support-plate crevices. Volume 2. Appendixes I through S. Final report

    International Nuclear Information System (INIS)

    Cassell, D.S.; Vroom, D.W.

    1983-01-01

    A test program was conducted to determine for selected steam generator tube supports the thermal/hydraulic conditions at the inception of dryout as indicated by a tube wall temperature excursion, to determine the pressure drop across the supports, and to obtain photographic documentation of the flow upstream and downstream of the supports. A multi-tube steam generator model was used and testing performed over the range of typcal PWR steam generator operating conditions. These appendices contain information on instrumentation calibration, test model and loop calibration, error analysis, test model thermal-hydraulic analyses, index of lab materials and log sheets, index of two-phase flow still photographs, index of high speed movies and video, test data printouts, test model and loop fabrication drawings, procedure for silver brazing tubewall thermocouples, and procedure for esablishing tube-tube support line contact

  13. Testing of small and large sign support systems FOIL test numbers : 92F009 and 92F010

    Science.gov (United States)

    1994-07-01

    This test report contains the results of two crash tests performed at the Federal Outdoor Impact Laboratory (FOIL) in McLean, Virginia. The/tests were performed on a small sign support system at 20 rni/h (8.9 m/s), test 92F009 and 60 mi/h (26.8 m/s),...

  14. Factors influencing the provision of end-of-life care in critical care settings: development and testing of a survey instrument.

    Science.gov (United States)

    Ranse, Kristen; Yates, Patsy; Coyer, Fiona

    2015-03-01

    To develop and psychometrically test a survey instrument to identify the factors influencing the provision of end-of-life care by critical care nurses. Following a decision to withdraw life-sustaining treatment, critical care nurses remain with the patient and their family providing end-of-life care. Identification of factors influencing the provision of this care can give evidence to inform practice development and support nurses. A cross-sectional survey of critical care nurses. An online survey was developed, reviewed by an expert panel and pilot tested to obtain preliminary evidence of its reliability and validity. In May 2011, a convenience sample of critical care nurses (n = 392, response rate 25%) completed the survey. The analytical approach to data obtained from the 58 items measured on a Likert scale included exploratory factor analysis and descriptive statistics. Exploratory factor analysis identified eight factors influencing the provision of end-of-life care: emotional support for nurses, palliative values, patient and family preferences, resources, organizational support, care planning, knowledge and preparedness. Internal consistency of each latent construct was deemed satisfactory. The results of descriptive statistics revealed a strong commitment to the inclusion of families in end-of-life care and the value of this care in the critical care setting. This paper reports preliminary evidence of the psychometric properties of a new survey instrument. The findings may inform practice development opportunities to support critical care nurses in the provision of end-of-life care and improve the care that patients and their families receive. © 2014 John Wiley & Sons Ltd.

  15. Standard practice of calibration of force-measuring instruments for verifying the force indication of testing machines

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2006-01-01

    1.1 The purpose of this practice is to specify procedures for the calibration of force-measuring instruments. Procedures are included for the following types of instruments: 1.1.1 Elastic force-measuring instruments, and 1.1.2 Force-multiplying systems, such as balances and small platform scales. Note 1Verification by deadweight loading is also an acceptable method of verifying the force indication of a testing machine. Tolerances for weights for this purpose are given in Practices E 4; methods for calibration of the weights are given in NIST Technical Note 577, Methods of Calibrating Weights for Piston Gages. 1.2 The values stated in SI units are to be regarded as the standard. Other metric and inch-pound values are regarded as equivalent when required. 1.3 This practice is intended for the calibration of static force measuring instruments. It is not applicable for dynamic or high speed force calibrations, nor can the results of calibrations performed in accordance with this practice be assumed valid for...

  16. The Impact of Scholastic Instrumental Music and Scholastic Chess Study on the Standardized Test Scores of Students in Grades Three, Four, and Five

    Science.gov (United States)

    Martinez, Edwin E.

    2012-01-01

    This study examines the impact of instrumental music study and group chess lessons on the standardized test scores of suburban elementary public school students (grades three through five) in Levittown, New York. The study divides the students into the following groups and compares the standardized test scores of each: a) instrumental music…

  17. Evaluation tests of the Instrumentation and Control equipment to use in nuclear power plants: its contribution to the improvement and quality certification of the Brazilian equipment

    International Nuclear Information System (INIS)

    Menezes, R.H.M. de; Peluso, M.A.V.

    1984-01-01

    This work presents the procedures used to evaluate Instrumentation Control equipment and reports the experience of integration among instrument user, manufacturer and test institution. It covers tests for equipments for conventional user and for specific application in Nuclear Power Stations. (Author) [pt

  18. The instrumented Timed Up and Go test: Potential outcome measure for disease modifying therapies in Parkinson's disease

    OpenAIRE

    Zampieri, Cris; Salarian, Arash; Carlson-Kuhta, Patricia; Aminian, Kamiar; Nutt, John G.; Horak, Fay B.

    2009-01-01

    The Timed Up and Go (TUG) test has been used to assess balance and mobility in Parkinson’s Disease (PD). However, it is not known if this test is sensitive to subtle abnormalities present in early stages of the disease, when balance and gait problems are not clinically evident but may be detected with instrumented analysis of movement. We hypothesize that postural transitions and arm swing during gait will be the most sensitive characteristics of the TUG for early PD. In the present study, we...

  19. Nuclear electronic equipment for control and monitoring panel. Procedure guide for on-site tests of nuclear reactor instruments

    International Nuclear Information System (INIS)

    1975-10-01

    By the use of a procedure for on-site testing of nuclear reactor instruments it should be possible to judge their ability to guarantee the reactor safety and availability at the moment of divergence or during operation. Such a procedure must therefore be created as a work implement for the quick and reliable installation of electronic devices necessary for nuclear reactor control and supervision. A standard document is proposed for this purpose, allowing a ''test programme'' to be set up before the equipment is installed on the site [fr

  20. Instrumentation for Testing Whether the Icy Moons of the Gas and Ice Giants Are Inhabited.

    Science.gov (United States)

    Chela-Flores, Julian

    2017-10-01

    Evidence of life beyond Earth may be closer than we think, given that the forthcoming missions to the jovian system will be equipped with instruments capable of probing Europa's icy surface for possible biosignatures, including chemical biomarkers, despite the strong radiation environment. Geochemical biomarkers may also exist beyond Europa on icy moons of the gas giants. Sulfur is proposed as a reliable geochemical biomarker for approved and forthcoming missions to the outer solar system. Key Words: JUICE mission-Clipper mission-Geochemical biomarkers-Europa-Moons of the ice giants-Geochemistry-Mass spectrometry. Astrobiology 17, 958-961.

  1. Community support essential to better malaria testing | IDRC ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    In 2010, Ghana adopted World Health Organization guidelines for quickly and inexpensively diagnosing malaria. Yet, says Nana Yaa Boadu, healthcare practitioners still treat feverish patients without testing. Building on her 2011 IDRC Doctoral Research Award, Nana's 2014 Research Award helped her identify why this ...

  2. Full-Scale Instrumented Testing and Analysis of Matting Systems for Airfield Parking Ramps and Taxiways

    National Research Council Canada - National Science Library

    Gartrell, Chad A

    2007-01-01

    ... C-17. Several test sections with differing strength soils were built with chosen mats tested in an elimination method, using a load cart that simulates contingency loading of one main gear of the C-17...

  3. Development and Acceptance Testing of the Dual Wheel Mechanism for the Tunable Filter Imager Cryogenic Instrument on the JWST

    Science.gov (United States)

    Leckie, Martin; Ahmad, Zakir

    2010-01-01

    The James Webb Space Telescope (JWST) will carry four scientific instruments, one of which is the Tunable Filter Imager (TFI), which is an instrument within the Fine Guidance Sensor. The Dual Wheel (DW) mechanism is being designed, built and tested by COM DEV Ltd. under contract from the Canadian Space Agency. The DW mechanism includes a pupil wheel (PW) holding seven coronagraphic masks and two calibration elements and a filter wheel (FW) holding nine blocking filters. The DW mechanism must operate at both room temperature and at 35K. Successful operation at 35K comprises positioning each optical element with the required repeatability, for several thousand occasions over the five year mission. The paper discusses the results of testing geared motors and bearings at the cryogenic temperature. In particular bearing retainer design and PGM-HT material, the effects of temperature gradients across bearings and the problems associated with cooling mechanisms down to cryogenic temperatures. The results of additional bearing tests are described that were employed to investigate an abnormally high initial torque experienced at cryogenic temperatures. The findings of these tests, was that the bearing retainer and the ball/race system could be adversely affected by the large temperature change from room temperature to cryogenic temperature and also the temperature gradient across the bearing. The DW mechanism is now performing successfully at both room temperature and at cryogenic temperature. The life testing of the mechanism is expected to be completed in the first quarter of 2010.

  4. Diagnosing ADHD in Adults: An Examination of the Discriminative Validity of Neuropsychological Tests and Diagnostic Assessment Instruments.

    Science.gov (United States)

    Pettersson, Richard; Söderström, Staffan; Nilsson, Kent W

    2015-12-17

    The objective of this study is to investigate the discriminative validity of neuropsychological tests and diagnostic assessment instruments in diagnosing adult ADHD in a clinical psychiatric population. Of 108 patients, 60 were diagnosed with ADHD. The Diagnostic Interview for ADHD in adults (DIVA 2.0) and Adult ADHD Self-Report Scale (ASRS) v.1.1 together with eight neuropsychological tests were investigated. All instruments showed poor discriminative ability except for the DIVA, which showed a relatively good ability to discriminate between the groups (sensitivity = 90.0; specificity = 72.9). A logistic regression analysis model with the DIVA and measures of inattention, impulsivity, and activity from continuous performance tests (CPTs) showed a sensitivity of 90.0 and a specificity of 83.3. Neuropsychological tests have a poor ability to discriminate between patients diagnosed with ADHD and patients not diagnosed with ADHD, but variables from CPT tests can contribute to increasing the specificity by 10% if used in combination with the DIVA. © The Author(s) 2015.

  5. [Interview instrument provides no reliable assessment of suicide risk. Scientific support is lacking according to report from the Swedish Council on Health Technology Assessment (SBU)].

    Science.gov (United States)

    Runeson, Bo

    2015-12-08

    Identifying individuals at risk of future suicide or suicide attempts is of clinical importance. Instruments have been developed to facilitate the assessment of the risk of future suicidal acts. A systematic review was conducted using the standard methods of the Swedish Council on Health Technology Assessment (SBU). The ability of the instrument to predict risk for future suicide/suicide attempt was assessed at follow up. The methodological quality of eligible studies was assessed; studies with moderate or low risk of bias were analysed in accordance with GRADE. None of the included studies provided scientific evidence to support that any instrument had sufficient accuracy to predict future suicidal behaviour. There is strong evidence to support that the SAD PERSONS Scale has very low sensitivity; most persons who make future suicidal acts are not identified.

  6. Test of ground-based lidar instrument WLS7-159

    DEFF Research Database (Denmark)

    Gómez Arranz, Paula; Wagner, Rozenn

    This report presents the result of the test performed for the given Windcube at DTU’s test site for large wind turbine at Høvsøre, Denmark. The test aims at establishing a relation between the reference wind measurements and corresponding lidar wind indications, and evaluating a set of quality ch...... checks defined by the customer....

  7. Test of ground-based Lidar instrument WLS200S-10

    DEFF Research Database (Denmark)

    Gómez Arranz, Paula

    This report presents the result of the test performed for the given Windcube at DTU’s test site for large wind turbine at Høvsøre, Denmark. The test aims at establishing a relation between the reference wind measurements and corresponding lidar wind indications, and evaluating a set of quality...

  8. Test of ground-based Lidar instrument WLS7-106

    DEFF Research Database (Denmark)

    Gómez Arranz, Paula

    This report presents the result of the test performed for the given Windcube at DTU’s test site for large wind turbine at Høvsøre, Denmark. The test aims at establishing a relation between the reference wind measurements and corresponding lidar wind indications, and evaluating a set of quality...

  9. Test of ground-based Lidar instrument WLS200S-11

    DEFF Research Database (Denmark)

    Gómez Arranz, Paula

    This report presents the result of the test performed for the given Windcube at DTU’s test site for large wind turbine at Høvsøre, Denmark. The test aims at establishing a relation between the reference wind measurements and corresponding lidar wind indications, and evaluating a set of quality...

  10. Development and cross-cultural testing of the International Depression Symptom Scale (IDSS): a measurement instrument designed to represent global presentations of depression.

    Science.gov (United States)

    Haroz, E E; Bass, J; Lee, C; Oo, S S; Lin, K; Kohrt, B; Michalopolous, L; Nguyen, A J; Bolton, P

    2017-01-01

    Self-report measurement instruments are commonly used to screen for mental health disorders in Low and Middle-Income Countries (LMIC). The Western origins of most depression instruments may constitute a bias when used globally. Western measures based on the DSM, do not fully capture the expression of depression globally. We developed a self-report scale design to address this limitation, the International Depression Symptom Scale-General version (IDSS-G), based on empirical evidence of the signs and symptoms of depression reported across cultures. This paper describes the rationale and process of its development and the results of an initial test among a non-Western population. We evaluated internal consistency reliability, test-retest reliability and inter-rater reliability of the IDSS-G in a sample N  = 147 male and female attendees of primary health clinics in Yangon, Myanmar. For criterion validity, IDSS-G scores were compared with diagnosis by local psychiatrists using the Structured Clinical Interview for DSM (SCID). Construct validity was evaluated by investigating associations between the IDSS-G and the Patient Health Questionnaire (PHQ), impaired function, and suicidal ideation. The IDSS-G showed high internal consistency reliability ( α  = 0.92), test-retest reliability ( r  = 0.87), and inter-rater reliability ( ICC  = 0.90). Strong correlations between the IDSS-G and PHQ-9, functioning, and suicidal ideation supported construct validity. Criterion validity was supported for use of the IDSS-G to identify people with a SCID diagnosed depressive disorder (major depression/dysthymia). The IDSS-G also demonstrated incremental validity by predicting functional impairment beyond that predicted by the PHQ-9. Results suggest that the IDSS-G accurately assesses depression in this population. Future testing in other populations will follow.

  11. In core instrumentation for online nuclear heating measurements of material testing reactor

    International Nuclear Information System (INIS)

    Reynard, C.; Andre, J.; Brun, J.; Carette, M.; Janulyte, A.; Merroun, O.; Zerega, Y.; Lyoussi, A.; Bignan, G.; Chauvin, J-P.; Fourmentel, D.; Glayse, W.; Gonnier, C.; Guimbal, P.; Iracane, D.; Villard, J.-F.

    2010-01-01

    The present work focuses on nuclear heating. This work belongs to a new advanced research program called IN-CORE which means 'Instrumentation for Nuclear radiations and Calorimetry Online in REactor' between the LCP (University of Provence-CNRS) and the CEA (French Atomic Energy Commission) - Jules Horowitz Reactor (JHR) program. This program started in September 2009 and is dedicated to the conception and the design of an innovative mobile experimental device coupling several sensors and ray detectors for on line measurements of relevant physical parameters (photonic heating, neutronic flux ...) and for an accurate parametric mapping of experimental channels in the JHR Core. The work presented below is the first step of this program and concerns a brief state of the art related to measurement methods of nuclear heating phenomena in research reactor in general and MTR in particular. A special care is given to gamma heating measurements. A first part deals with numerical codes and models. The second one presents instrumentation divided into various kinds of sensor such as calorimeter measurements and gamma ionization chamber measurements. Their basic principles, characteristics such as metrological parameters, operating mode, disadvantages/advantages, ... are discussed. (author)

  12. Testing the Deployment Repeatability of a Precision Deployable Boom Prototype for the Proposed SWOT Karin Instrument

    Science.gov (United States)

    Agnes, Gregory S.; Waldman, Jeff; Hughes, Richard; Peterson, Lee D.

    2015-01-01

    NASA's proposed Surface Water Ocean Topography (SWOT) mission, scheduled to launch in 2020, would provide critical information about Earth's oceans, ocean circulation, fresh water storage, and river discharge. The mission concept calls for a dual-antenna Ka-band radar interferometer instrument, known as KaRIn, that would map the height of water globally along two 50 km wide swaths. The KaRIn antennas, which would be separated by 10 meters on either side of the spacecraft, would need to be precisely deployable in order to meet demanding pointing requirements. Consequently, an effort was undertaken to design build and prototype a precision deployable Mast for the KaRIn instrument. Each mast was 4.5-m long with a required dilitation stability of 2.5 microns over 3 minutes. It required a minimum first mode of 7 Hz. Deployment repeatability was less than +/- 7 arcsec in all three rotation directions. Overall mass could not exceed 41.5 Kg including any actuators and thermal blanketing. This set of requirements meant the boom had to be three times lighter and two orders of magnitude more precise than the existing state of the art for deployable booms.

  13. Plutonium Speciation in Support of Oxidative-Leaching Demonstration Test

    International Nuclear Information System (INIS)

    Sinkov, Sergey I.

    2007-01-01

    Bechtel National, Inc. (BNI) is evaluating the plutonium speciation in caustic solutions that reasonably represent the process streams from the oxidative-leaching demonstration test. Battelle-Pacific Northwest Division (PNWD) was contracted to develop a spectrophotometric method to measure plutonium speciation at submicromolar (< 10-6 M) concentrations in alkaline solutions in the presence of chromate and carbonate. Data obtained from the testing will be used to identify the oxidation state of Pu(IV), Pu(V), and Pu(VI) species, which potentially could exist in caustic leachates. Work was initially conducted under contract number 24590-101-TSA-W000-00004 satisfying the needs defined in Appendix C of the Research and Technology Plan TSS A-219 to evaluate the speciation of chromium, plutonium, and manganese before and after oxidative leaching. In February 2007, the contract mechanism was switched to Pacific Northwest National Laboratory PNNL Operating Contract MOA: 24590-QL-HC9-WA49-00001

  14. Pilot Study: Foam Wedge Chin Support Static Tolerance Testing

    Science.gov (United States)

    2017-10-24

    Government. The fact that the Government formulated or supplied the drawings, specifications, or other data does not license the holder or any other...regarding the comfort, fit, and positive benefits that could potentially come from the use of the foam wedge to mitigate neck pain. Overall, testing showed... benefit to pilots that choose to use the foam wedge, and therefore feel that the device should be made available to aviators. From the results of this

  15. Instrument for controlling the application of mechanical loads to biological and bicompatible test subjects

    Science.gov (United States)

    Lintilhac, P.M.; Vesecky, T.B.

    1995-09-19

    An apparatus and methods are disclosed facilitating the application of forces and measurement of dimensions of a test subject. In one arrangement the test subject is coupled to a forcing frame and controlled forces applied thereto. Force applied to the test subject is measured and controlled. A dimensional characteristic of the test subject, such as growth, is measured by a linear variable differential transformer. The growth measurement data can be used to control the force applied. The transducer module receives force and dimensional data from the forcing frame. The transducer module is a separate, microprocessor-based unit that communicates the test data to a controller unit that controls the application of force to the test subject and receives the test data from the transducer module for force control, storage, and/or communication to the user. 8 figs.

  16. Ion Exchange Column Tests Supporting Technetium Removal Resin Maturation

    Energy Technology Data Exchange (ETDEWEB)

    Nash, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); McCabe, D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hamm, L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Smith, F. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Morse, M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2013-12-20

    The primary treatment of the tank waste at the DOE Hanford site will be done in the Waste Treatment and Immobilization Plant, currently under construction. The baseline plan for this facility is to treat the waste, splitting it into High Level Waste (HLW) and Low Activity Waste (LAW). Both waste streams are then separately vitrified as glass and sealed in canisters. The LAW glass will be disposed on site. There are currently no plans to treat the waste to remove technetium, so its disposition path is the LAW glass. Due to the soluble properties of pertechnetate and long half-life of 99Tc, effective management of 99Tc is important. Options are being explored to immobilize the supplemental LAW portion of the tank waste, as well as to examine the volatility of 99Tc during the vitrification process. Removal of 99Tc, followed by off-site disposal has potential to reduce treatment and disposal costs. A conceptual flow sheets for supplemental LAW treatment and disposal that could benefit from technetium removal will specifically examine removing 99Tc from the LAW feed stream to supplemental immobilization. SuperLig® 639 is an elutable ion exchange resin. In the tank waste, 99Tc is predominantly found in the tank supernate as pertechnetate (TcO4-). Perrhenate (ReO4-) has been shown to be a good non-radioactive surrogate for pertechnetate in laboratory testing for this ion exchange resin. This report contains results of experimental ion exchange distribution coefficient and column resin maturation kinetics testing using the resin SuperLig® 639a to selectively remove perrhenate from simulated LAW. This revision includes results from testing to determine effective resin operating temperature range. Loading tests were performed at 45°C, and the computer modeling was updated to include the temperature effects. Equilibrium contact testing indicated that this batch of

  17. Testing an Irrigation Decision Support Tool for California Specialty Crops

    Science.gov (United States)

    Johnson, L.; Cahn, M.; Benzen, S.; Zaragoza, I.; Murphy, L.; Melton, F. S.; Martin, F.; Quackenbush, A.; Lockhart, T.

    2015-12-01

    Estimation of crop evapotranspiration supports efficiency of irrigation water management, which in turn can mitigate nitrate leaching, groundwater depletion, and provide energy savings. Past research in California and elsewhere has revealed strong relationships between photosynthetically active vegetation fraction (Fc) and crop evapotranspiration (ETc). Additional research has shown the potential of monitoring Fc by satellite remote sensing. The U.C. Cooperative Extension developed and operates CropManage (CM) as on-line database irrigation (and nitrogen) scheduling tool. CM accounts for the rapid growth and typically brief cycle of cool-season vegetables, where Fc and fraction of reference ET can change daily during canopy development. The model automates crop water requirement calculations based on reference ET data collected by California Dept. Water Resources. Empirically-derived equations are used to estimate daily Fc time-series for a given crop type primarily as a function of planting date and expected harvest date. An application programming interface (API) is under development to provide a check on modeled Fc of current crops and facilitate CM expansion to new crops. The API will enable CM to extract field scale Fc observations from NASA's Satellite Irrigation Management Support (SIMS). SIMS is mainly Landsat based and currently monitors Fc over about 8 million irrigation acres statewide, with potential for adding data from ESA/Sentinel for improved temporal resolution. In the current study, a replicated irrigation trial was performed on romaine lettuce at the USDA Agricultural Research Station in Salinas, CA. CropManage recommendations were used to guide water treatments by drip irrigation at 50%, 75%, 100% ETc replacement levels, with an added treatment at 150% ET representing grower standard practice. Experimental results indicate that yields from the 100% and 150% treatments were not significantly different and were in-line with industry average, while

  18. Psychometric Testing of INTEGRARE, an Instrument for the Assesment of Pressure Ulcer Risk in Inpatients.

    Science.gov (United States)

    Porcel-Gálvez, Ana María; Romero-Castillo, Rocío; Fernández-García, Elena; Barrientos-Trigo, Sergio

    2017-08-21

    The aim of this study is to evaluate the psychometric properties of INTEGRARE, an instrument based on Nursing Outcome Classification. A multicenter, cross-sectional, methodological design was used. The study included 3,835 patients. Internal consistency α = 0.86. Confirmatory factor analysis demonstrated the unidimensionality of the scale, indicating a good model fit (CMIN/DF = 4; GFI, CFI, NFI, IFI = 0.999; RMSEA = 0.028). INTEGRARE is a valid and reliable instrument with high sensitivity, specificity, and diagnostic accuracy in measuring pressure ulcer (PU) risk in inpatients. This instrument allows us to know the effectiveness of nursing interventions, providing evidence for the validation of the diagnosis Risk for pressure ulcer (00249) as well as on health outcomes, due to the fact that PUs are nursing-sensitive outcomes. Evaluar las propiedades psicométricas de INTEGRARE, un instrumento basado en la Clasificación de Resultados de Enfermería. MÉTODO: Se optó por un diseño transversal multicéntrico. El estudio incluyó a 3,835 pacientes. Consistencia interna α = 0.86. El análisis factorial confirmatorio demostró la unidimensionalidad de la escala, indicando un buen ajuste del modelo (CMIN/DF = 4; GFI, CFI, NFI, IFI = 0.999; RMSEA = 0.028). INTEGRARE es un instrumento válido y fiable con alta sensibilidad, especificidad y precisión diagnóstica en la medición de riesgo de úlcera por presión (UPP) en pacientes hospitalizados. IMPLICACIONES PARA LA PRÁCTICA ENFERMERA: Este instrumento nos permite conocer la efectividad de las intervenciones enfermeras, aportando evidencia para la validación del diagnóstico Riesgo de úlcera por presión (00249), así como sobre los resultados de salud, debido a que las UPP son resultados sensibles a la práctica enfermera. © 2017 NANDA International, Inc.

  19. Full-scale vibration tests of Atucha II N.P.P. Part I: objectives, instrumentation and test description

    International Nuclear Information System (INIS)

    Konno, T.; Tsugawa, T.; Sala, G.; Friebe, T.M.; Prato, C.A.; Godoy, A.R.

    1995-01-01

    The main purpose of the tests was to provide experimental data on the dynamic characteristics of the main reactor building and adjacent structures of a full-scale nuclear power plant built on deep Quaternary soil deposits. Test results were intended to provide a benchmark case for control and calibration of state-of-the-art numerical techniques used for engineering design of new plants and assessment of existing facilities. Interpretation of test results and calibration of numerical analyses are described in other associated papers. (author). 5 figs

  20. 105 K east ion exchange and cartridge filter restart instrumentation acceptance test report

    International Nuclear Information System (INIS)

    Whitehurst, R.

    1996-01-01

    Acceptance Test Report following the completion of ATP-012 for the 105KE CP-A and CP-A Computer and PLC Panels. The test was conducted from 11/13/95 to 12/11/95. Three test discrepancies were generated during the ATP and all were dispositioned and closed. All sections were completed except Section 5.9 which was deleted per ECN 190556