WorldWideScience

Sample records for test du modele

  1. Test of the little Higgs model in Atlas at LHC: simulation of the digitization of the electromagnetic calorimeter; Test du modele du petit Higgs dans ATLAS au LHC: simulation de la numerisation du calorimetre electromagnetique

    Energy Technology Data Exchange (ETDEWEB)

    Lechowski, M

    2005-04-15

    LHC is a proton-proton collider with an energy of 14 TeV in the center of mass, which will start operating in 2007 at CERN. Two of its experiments, ATLAS, and CMS, will search and study in particular the Higgs boson, Supersymmetry and other new physics. This thesis was about two aspects of the ATLAS experiment. On one hand the simulation of the liquid Argon electromagnetic calorimeter, with the emulation of the electronic chain in charge of the digitization of the signal and also the evaluation of the electronic noise and the pile-up noise (coming from minimum bias events of inelastic collisions at LHC). These two points have been validated by the analysis of the data taken during beam tests in 2002 and 2004. On the other hand, a physics study concerning the Little Higgs model. This recent model solves the hierarchy problem of the Standard Model, in introducing new heavy particles to cancel quadratic divergences arising in the calculation of the Higgs boson mass. These new particles, with a mass about the TeV/c{sup 2}, are a heavy quark top, heavy gauge bosons Z{sub H}, W{sub H} and A{sub H}, and a heavy Higgs boson triplet. The physics study dealt with the characteristic decays of the model, Z{sub H} in Z + H and W{sub H} in W + H, with a Higgs mass either at 120 GeV/c{sup 2} decaying in two photons or at 200 GeV/c{sup 2} decaying in ZZ or WW. Results show that in both cases, for 300 fb{sup -1} (3 years at high luminosity), an observation of the signal at 5 {sigma} for Z{sub H} et W{sub H} masses less than 2 TeV/c{sup 2} is possible, covering a large part of the parameter space. (author)

  2. Standard model parameters determination and validity tests in Z{sup 0} hadronic disintegrations; Determination des parametres du modele standard et tests de sa validite dans les desintegrations hadroniques du Z{sup 0}

    Energy Technology Data Exchange (ETDEWEB)

    Todorov, T

    1993-05-01

    This thesis describes the determination of the electroweak parameters from the measurements of the total hadronic cross-section by the DELPHI experiment at LEP-I. The analysed data was taken in the years 1991 and 1992; a previous analysis of the data taken in 1990 is included in the final fits. The first part of the thesis describes the interest of the measurement of the Z{sup 0} resonance parameters in the framework of the Standard Model as well as their implications for alternative models. The Standard Model predictions are described in some detail, and their precision is estimated. Then follows a brief description of the LEP collider, of the measurement of the collision energy, and of the experimental setup. A chapter is devoted to the description of the luminosity measurement, essential for the determination of total cross-sections. The measurement of the hadronic cross-section (event selection, study of backgrounds, study of sources of systematic uncertainties) is described in detail in the next chapter. Then follows a description of the method of the extraction of the resonance parameters, and a discussion of the uncertainties in their determination. The values obtained are interpreted in the framework of the Standard Model, as well as in the framework of some more general theories. Finally, the event generator for hadron production in two-photon collisions is described in the appendix. (author). 69 refs., 51 figs., 9 tabs., 1 ann.

  3. From the validation of the standard model to the search for gravitational waves; Des tests du modele standard a la recherche d'ondes gravitationnelles

    Energy Technology Data Exchange (ETDEWEB)

    Tournefier, E

    2006-09-15

    The author reviews his activities concerning particle physics at Lep and LHC (Large Hadron Collider - CERN) and his latest works in the domain of gravitational waves. He has contributed first to the measurement of the parameters of the Z boson resonance and then to the extraction from experimental data of the standard model parameters like boson Higgs mass, top quark mass or the strong coupling constant. He has also worked on the development and testing of a LHC detector that will be useful to search for the Higgs boson via its decay in 2 photons. The Virgo experiment aims at detecting gravitational waves through interferometry, the author describes his contribution to the design of the detection system and gives a detailed review of the expected technical background noises. (A.C.)

  4. Evaluation du test rapide oral aware™ omt HIV 1/2 pour le ...

    African Journals Online (AJOL)

    Chaque participant a fourni un échantillon de fluide oral pour la réalisation du test Aware™ OMT HIV-1/2 et du sang testé suivant l'algorithme séquentiel de tests ELISAs Murex® HIV-1.2.0 (Laboratoires Abbott, Japon) et Test ELISA peptidique maison du CeDReS. Résultats : la sensibilité, la spécificité, la Valeur Prédictive ...

  5. Card sorting, test d’oculométrie et test d’utilisabilité sur le site web du Service d’information scientifique du CERN

    CERN Document Server

    Marchand, Alizée; Schneider, René

    Ce travail de Bachelor a pour objectif l’évaluation du site web du Service d’information scientifique du CERN. Cette évaluation est basée sur les méthodes utilisées en User Centered Design (UCD). Pour effectuer cette évaluation, nous avons sélectionné trois tests : un card sorting, un test d’oculométrie et un test d’utilisabilité. Selon la norme ISO 9241-11 :1998, l’utilisabilité se définit par « le degré selon lequel un produit peut être utilisé, par des utilisateurs identifiés, pour atteindre les buts définis avec efficacité, efficience et satisfaction, dans un contexte d’utilisation spécifié ». Les tests que nous avons réalisés nous ont permis d’identifier les problèmes d’utilisabilité du site du Service, en nous appuyant sur les caractéristiques d’utilisabilité définies dans cette norme. Pour ce faire, nous avons élaboré les tests en nous basant sur les pratiques utilisées par les spécialistes en UCD. Nous avons ensuite proposé à des employés du CERN, ...

  6. Utilisation du test GeneXpert pour le diagnostic de la tuberculose au ...

    African Journals Online (AJOL)

    Utilisation du test GeneXpert pour le diagnostic de la tuberculose au service des maladies infectieuses du CHNU de Fann. Sylvie Audrey Diop, Aminata Massaly, Daye Ka, Noel Magloire Manga, Louise Fortes-Déguénonvo, Cheikh Tidiane Ndour, Viviane Marie Pierre Cisse, Moussa Seydi ...

  7. Test dig selv: Hvilken type projektleder er du?

    DEFF Research Database (Denmark)

    Lund Pedersen, Carsten; Ritter, Thomas

    2018-01-01

    Hver person har sin egen måde at organisere et givent projekt på. Her kan du læse om fire typer af projektledere, som de fleste møder – og om hvorfor en mangfoldighed i typer er godt i enhver organisation....

  8. Analysis of in-R12 CHF data: influence of hydraulic diameter and heating length; test of Weisman boiling crisis model; Analyse de donnees de flux critique en R12: influence du diametre hydraulique et de la longueur chauffante; test du modele de Weisman

    Energy Technology Data Exchange (ETDEWEB)

    Czop, V; Herer, C; Souyri, A; Garnier, J

    1993-09-01

    In order to progress on the comprehensive modelling of the boiling crisis phenomenon, Electricite de France (EDF), Commissariat a l`Energie Atomique (CEA) and FRAMATOME have set up experimental programs involving in-R12 tests: the EDF APHRODITE program and the CEA-EDF-FRAMATOME DEBORA program. The first phase in these programs aims to acquire critical heat flux (CHF) data banks, within large thermal-hydraulic parameter ranges, both in cylindrical and annular configurations, and with different hydraulic diameters and heating lengths. Actually, three data banks have been considered in the analysis, all of them concerning in-R12 round tube tests: - the APHRODITE data bank, obtained at EDF with a 13 mn inside diameter, - the DEBORA data bank, obtained at CEA with a 19.2 mm inside diameter, - the KRISTA data bank, obtained at KfK with a 8 mm inside diameter. The analysis was conducted using CHF correlations and with the help of an advanced mathematical tool using pseudo-cubic thin plate type Spline functions. Two conclusions were drawn: -no influence of the heating length on our CHF results, - the influence of the diameter on the CHF cannot be simply expressed by an exponential function of this parameter, as thermal-hydraulic parameters also have an influence. Some calculations with Weisman and Pei theoretical boiling crisis model have been compared to experimental values: fairly good agreement was obtained, but further study must focus on improving the modelling of the influence of pressure and mass velocity. (authors). 12 figs., 4 tabs., 21 refs.

  9. Comparative study on DuPont analysis and DEA models for measuring stock performance using financial ratio

    Science.gov (United States)

    Arsad, Roslah; Shaari, Siti Nabilah Mohd; Isa, Zaidi

    2017-11-01

    Determining stock performance using financial ratio is challenging for many investors and researchers. Financial ratio can indicate the strengths and weaknesses of a company's stock performance. There are five categories of financial ratios namely liquidity, efficiency, leverage, profitability and market ratios. It is important to interpret the ratio correctly for proper financial decision making. The purpose of this study is to compare the performance of listed companies in Bursa Malaysia using Data Envelopment Analysis (DEA) and DuPont analysis Models. The study is conducted in 2015 involving 116 consumer products companies listed in Bursa Malaysia. The estimation method of Data Envelopment Analysis computes the efficiency scores and ranks the companies accordingly. The Alirezaee and Afsharian's method of analysis based Charnes, Cooper and Rhodes (CCR) where Constant Return to Scale (CRS) is employed. The DuPont analysis is a traditional tool for measuring the operating performance of companies. In this study, DuPont analysis is used to evaluate three different aspects such as profitability, efficiency of assets utilization and financial leverage. Return on Equity (ROE) is also calculated in DuPont analysis. This study finds that both analysis models provide different rankings of the selected samples. Hypothesis testing based on Pearson's correlation, indicates that there is no correlation between rankings produced by DEA and DuPont analysis. The DEA ranking model proposed by Alirezaee and Asharian is unstable. The method cannot provide complete ranking because the values of Balance Index is equal and zero.

  10. Heat transfer tests conducted on full-scale model, to investigate cooling conditions of EL.3 experimental reactor; Essais de transmission de chaleur sur maquette pour l'etude du refroidissement de la pile EL 3

    Energy Technology Data Exchange (ETDEWEB)

    Raievski, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Butzbach, M; Domenjoud, M [Alsthom, 75 - Paris (France); Bousquet, M [Chantiers de l' Atlantique (France); Braudeau, M; Milliat, M [Electricite de France (EDF), 75 - Paris (France)

    1958-07-01

    For such high heat flux density as is released in the channels of EL3 reactor (2.10{sup 6} kcal/m{sup 2}h on the hottest point) cooling conditions have proved to be satisfactory, that is free from nucleate boiling. The arrangements provided for these tests and the technique used for measurements (of temperature particularly) are specified. Two fields have been investigated: in the former (forced convection without nucleate boiling) a good agreement is found with Colburn's formula. The influence of the ratio L/D is pointed out. The latter field is of forced convection with beginning of nucleate boiling; there the observed raise of the transfer coefficient has been shown occurring with some delay. (author)Fren. [French] A la valeur elevee prevue pour la densite de flux de chaleur (2.10{sup 6} kcal/m{sup 2}h au point le plus chaud) il est verifie que le refroidissement de la pile s'effectue normalement (sans ebullition de paroi). Les essais sont menes sur la maquette grandeur nature d'un canal d'EL3. Les dispositions relatives a la conduite des essais et a la technique des mesures (de temperature en particulier) sont precisees. Deux domaines sont etudies; pour t{sub p} < T{sub sat} (convection forcee sans ebullition de paroi) on constate un bon accord avec la formule de Colburn, avec toutefois l'influence du rapport L/D. Pour t{sub p} < T{sub sat} (debut d'ebullition) l'augmentation prevue du coefficient de transmission presente un certain retard. (auteur)

  11. 23 octobre 2012 - Le Président du Conseil général de la Haute-Savoie C. Monteil signe le livre d'or en présence du Directeur général R. Heuer, la chef des Relations Internationales F. Pauss, le chef du département Physique P. Bloch et le chef du département Technologie F. Bordry; visite du hall de test des aimants supraconducteurs du LHC avec F. Bordry.

    CERN Multimedia

    Maximilien Brice

    2012-01-01

    23 octobre 2012 - Le Président du Conseil général de la Haute-Savoie C. Monteil signe le livre d'or en présence du Directeur général R. Heuer, la chef des Relations Internationales F. Pauss, le chef du département Physique P. Bloch et le chef du département Technologie F. Bordry; visite du hall de test des aimants supraconducteurs du LHC avec F. Bordry.

  12. Beyond the standard model; Au-dela du modele standard

    Energy Technology Data Exchange (ETDEWEB)

    Cuypers, F. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1997-05-01

    These lecture notes are intended as a pedagogical introduction to several popular extensions of the standard model of strong and electroweak interactions. The topics include the Higgs sector, the left-right symmetric model, grand unification and supersymmetry. Phenomenological consequences and search procedures are emphasized. (author) figs., tabs., 18 refs.

  13. A mathematical model for cost of maritime transport. Application to competitiveness of nuclear vessels; Modele mathematique du cout de transport maritime application a la competitivite du navire nucleaire

    Energy Technology Data Exchange (ETDEWEB)

    Dorval, C [Commissariat a l' Energie Atomique, 75 - Paris (France)

    1966-05-01

    In studying the competitiveness of a nuclear merchant vessel, economic assessments in terms of figures were discarded in favor of a simplified model, which gives a clearer idea of the mechanism of the comparison between alternative vessels and the particular influence of each parameter. An expression is formulated for the unit cost per ton carried over a given distance as a function of the variables (speed and deadweight tonnage) and is used to determine the optima for conventional and nuclear vessels. To represent the freight market involved in the optimization studies, and thus in the competitiveness computation, two cases are taken into account: the tonnage to be carried annually is limited, and the tonnage to be carried annually is not limited. In both cases the optima are calculated and compared for a conventional and a nuclear vessel. Competitiveness curves are plotted as a function of the ratios of nuclear and conventional fuel costs and nuclear and conventional marginal power costs. These curves express the limiting values of the above two ratios for which the transport costs of the nuclear and conventional vessels are equal. The competitiveness curves vary considerably according to the hypothesis adopted for the freight market and the limit of tonnage carried annually. (author) [French] Pour etudier la competitivite du navire marchand nucleaire, plutot que de nous livrer a des evaluations economiques chiffrees, discutables dans l'etat actuel des etudes, nous utilisons un modele simplifie permettant de mieux saisir le mecanisme de la comparaison des navires et l'influence particuliere de chaque parametre. Nous etablissons une expression du cout unitaire de la tonne transportee sur un parcours donne en fonction des variables vitesse et port en lourd. Et nous l'utilisons pour determiner les optima des navires classiques et nucleaires. Pour representer le marche du fret qui intervient dans les etudes d'optimisation, et donc dans la recherche de la

  14. Evaluating Bank Profitability in Ghana: A five step Du-Pont Model Approach

    Directory of Open Access Journals (Sweden)

    Baah Aye Kusi

    2015-09-01

    Full Text Available We investigate bank profitability in Ghana using periods before, during and after the globe financial crises with the five step du-pont model for the first time.We adapt the variable of the five step du-pont model to explain bank profitability with a panel data of twenty-five banks in Ghana from 2006 to 2012. To ensure meaningful generalization robust errors fixed and random effects models are used.Our empirical results suggests that bank operating activities (operating profit margin, bank efficiency (asset turnover, bank leverage (asset to equity and financing cost (interest burden  were positive and significant determinants of bank profitability (ROE during the period of study implying that bank in Ghana can boost return to equity holders through the above mentioned variables. We further report that the five step du-pont model better explains the total variation (94% in bank profitability in Ghana as compared to earlier findings suggesting that bank specific variables are keen in explaining ROE in banks in Ghana.We cited no empirical study that has employed five step du-pont model making our study unique and different from earlier studies as we assert that bank specific variables are core to explaining bank profitability.                

  15. Des proprietes de l'etat normal du modele de Hubbard bidimensionnel

    Science.gov (United States)

    Lemay, Francois

    Depuis leur decouverte, les etudes experimentales ont demontre que les supra-conducteurs a haute temperature ont une phase normale tres etrange. Les proprietes de ces materiaux ne sont pas bien decrites par la theorie du liquide de Fermi. Le modele de Hubbard bidimensionnel, bien qu'il ne soit pas encore resolu, est toujours considere comme un candidat pour expliquer la physique de ces composes. Dans cet ouvrage, nous mettons en evidence plusieurs proprietes electroniques du modele qui sont incompatibles avec l'existence de quasi-particules. Nous montrons notamment que la susceptibilite des electrons libres sur reseau contient des singularites logarithmiques qui influencent de facon determinante les proprietes de la self-energie a basse frequence. Ces singularites sont responsables de la destruction des quasi-particules. En l'absence de fluctuations antiferromagnetiques, elles sont aussi responsables de l'existence d'un petit pseudogap dans le poids spectral au niveau de Fermi. Les proprietes du modele sont egalement etudiees pour une surface de Fermi similaire a celle des supraconducteurs a haute temperature. Un parallele est etabli entre certaines caracteristiques du modele et celles de ces materiaux.

  16. Acceptabilité du test VIH proposé aux nourrissons dans les services pédiatriques, en Côte d'Ivoire, Significations pour la couverture du diagnostic pédiatrique

    Science.gov (United States)

    Oga, Maxime; Brou, Hermann; Dago-Akribi, Hortense; Coffie, Patrick; Amani-Bossé, Clarisse; Ékouévi, Didier; Yapo, Vincent; Menan, Hervé; Ndondoki, Camille; Timité-Konan, M.; Leroy, Valériane

    2014-01-01

    Résumé Problème: Le dépistage VIH chez les enfants a rarement été au centre des préoccupations des chercheurs. Quand le dépistage pédiatrique a retenu l'attention, cela a été pour éclairer seulement sur les performances diagnostiques en ignorant même que le test pédiatrique comme bien d'autres peut s'accepter ou se refuser. Cet article met au cœur de son analyse les raisons qui peuvent expliquer qu'on accepte ou qu'on refuse de faire dépister son enfant. Objectif: Etudier chez les parents, les mères, les facteurs explicatifs de l'acceptabilité du test VIH des nourrissons de moins de six mois. Méthodes: Entretien semi-directif à passages répétés avec les parents de nourrissons de moins de six mois dans les formations sanitaires pour la pesée/vaccination et les consultations pédiatriques avec proposition systématique d'un test VIH pour leur nourrisson. Résultats: Nous retenons que la réalisation effective du test pédiatrique du VIH chez le nourrisson repose sur trois éléments. Primo, le personnel de santé par son discours (qui dénote de ses connaissances et perceptions même sur l'infection) orienté vers les mères influence leur acceptation ou non du test. Secundo, la mère qui par ses connaissances et perceptions même sur le VIH, dont le statut particulier, l'impression de bien-être chez elle et son enfant influence toute réalisation du test pédiatrique VIH. Tertio, l'environnement conjugal de la mère, particulièrement caractérisé par les rapports au sein du couple, sur la facilité de parler du test VIH et sa réalisation chez les deux parents ou chez la mère seulement sont autant de facteurs qui influencent la réalisation effective du dépistage du VIH chez l'enfant. Le principe préventif du VIH, et le désir de faire tester l'enfant ne suffisent pas à eux seuls pour aboutir à sa réalisation effective, selon certaines mères confrontées au refus du conjoint. A l'opposé, les autres mères refusant la r

  17. Development and validation of a simulation tool dedicated to eddy current non destructive testing of tubes; Developpement d'un modele electromagnetique 3D pour la simulation du controle par Courants de Foucault de tubes en fabrication

    Energy Technology Data Exchange (ETDEWEB)

    Reboud, Ch

    2006-09-15

    Eddy current testing (ECT) technique is widely used in industrial fields such as iron and steel industry. Dedicated simulation tools provide a great assistance for the optimisation of ECT processes. CEA and the Vallourec Research Center have collaborated in order to develop a simulation tool of ECT of tubes. The volume integral method has been chosen for the resolution of Maxwell equations in a stratified medium, in order to get accurate results with a computation time short enough to carry out optimisation or inversion procedures. A fast model has been developed for the simulation of ECT of non magnetic tubes using specific external probes. New flaw geometries have been modelled: holes and notches with flat bottom. Validations of the developments, which have been integrated to the CIVA platform, have been carried out using experimental data recorded in laboratory conditions and in. industrial conditions, successively. The integral equations derived are solved using the Galerkin variant of the method of moments with pulse functions as projection functions. In order to overcome some memory limitations, other projection functions have been considered. A new discretization scheme based on non-uniform B-Splines of degree 1 or 2 has been implemented, which constitutes an original contribution to the existing literature. The decrease of the mesh size needed to get a given accuracy on the result may lead to the simulation of more complex ECT configurations. (author)

  18. Loglinear Rasch model tests

    NARCIS (Netherlands)

    Kelderman, Hendrikus

    1984-01-01

    Existing statistical tests for the fit of the Rasch model have been criticized, because they are only sensitive to specific violations of its assumptions. Contingency table methods using loglinear models have been used to test various psychometric models. In this paper, the assumptions of the Rasch

  19. Bringing the DuPont Profitability Model to Extension

    Science.gov (United States)

    Roucan-Kane, Maud; Wolfskill, L. A.; Boehlje, Michael D.; Gray, Allan W.

    2013-01-01

    This article discusses a financial training program used by Deere and Company for almost 10 years. The objective is to describe the program and to discuss a pre-test/post-test methodology to test the effectiveness of a program for possible duplication by Extension. Results show that participants significantly improved from the pre-test to the…

  20. Earthquake likelihood model testing

    Science.gov (United States)

    Schorlemmer, D.; Gerstenberger, M.C.; Wiemer, S.; Jackson, D.D.; Rhoades, D.A.

    2007-01-01

    INTRODUCTIONThe Regional Earthquake Likelihood Models (RELM) project aims to produce and evaluate alternate models of earthquake potential (probability per unit volume, magnitude, and time) for California. Based on differing assumptions, these models are produced to test the validity of their assumptions and to explore which models should be incorporated in seismic hazard and risk evaluation. Tests based on physical and geological criteria are useful but we focus on statistical methods using future earthquake catalog data only. We envision two evaluations: a test of consistency with observed data and a comparison of all pairs of models for relative consistency. Both tests are based on the likelihood method, and both are fully prospective (i.e., the models are not adjusted to fit the test data). To be tested, each model must assign a probability to any possible event within a specified region of space, time, and magnitude. For our tests the models must use a common format: earthquake rates in specified “bins” with location, magnitude, time, and focal mechanism limits.Seismology cannot yet deterministically predict individual earthquakes; however, it should seek the best possible models for forecasting earthquake occurrence. This paper describes the statistical rules of an experiment to examine and test earthquake forecasts. The primary purposes of the tests described below are to evaluate physical models for earthquakes, assure that source models used in seismic hazard and risk studies are consistent with earthquake data, and provide quantitative measures by which models can be assigned weights in a consensus model or be judged as suitable for particular regions.In this paper we develop a statistical method for testing earthquake likelihood models. A companion paper (Schorlemmer and Gerstenberger 2007, this issue) discusses the actual implementation of these tests in the framework of the RELM initiative.Statistical testing of hypotheses is a common task and a

  1. Author: MA du Plessis CLINICAL LEGAL EDUCATION MODELS ...

    African Journals Online (AJOL)

    21892687

    http://www.nuigalway.ie/business-public-policy-law/school-of-law/students/cle/. .... ...clinical legal education of final year LLB students, with the focus on analytical ..... Spot tests and minute papers can be applied successfully during student ...

  2. Neutron penetrabilities using an optical model potential (1963); Penetrabilites des neutrons selon le modele du potentiel optique (1963)

    Energy Technology Data Exchange (ETDEWEB)

    Mani, G S; Melkanoff, M A; Iori, I [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1963-07-01

    The neutron penetrabilities and reaction cross-sections are presented in these tables for the case of an optical model potential for the nucleus, for nuclei up to mass 230. (authors) [French] Les penetrabilites et les sections efficaces de reaction pour les neutrons sont donnees dans ces tables en utilisant le modele du potentiel optique, pour les noyaux cibles jusqu'a la masse 230. (auteurs)

  3. Neutron penetrabilities using an optical model potential (1963); Penetrabilites des neutrons selon le modele du potentiel optique (1963)

    Energy Technology Data Exchange (ETDEWEB)

    Mani, G.S.; Melkanoff, M.A.; Iori, I. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1963-07-01

    The neutron penetrabilities and reaction cross-sections are presented in these tables for the case of an optical model potential for the nucleus, for nuclei up to mass 230. (authors) [French] Les penetrabilites et les sections efficaces de reaction pour les neutrons sont donnees dans ces tables en utilisant le modele du potentiel optique, pour les noyaux cibles jusqu'a la masse 230. (auteurs)

  4. Control and diagnosis oriented modelling of the compression ignition engine; Modelisation du moteur a allumage par compression dans la perspective du controle et du diagnostic

    Energy Technology Data Exchange (ETDEWEB)

    Grondin, O

    2004-12-15

    This thesis has described an investigation into the modelling of compression ignition engine for control and diagnosis purpose. The Diesel engine is the most efficient and clean internal combustion engine due to modem electromechanical actuators. However, pollutant emission regulations are much more stricter, thus, these complex systems need sophisticated and efficient control algorithms to reach very low emission levels. For this task, engine models are required at each step of the control system development: control laws synthesis, simulation and validation. The system under study is a six cylinder direct injection Diesel engine fitted with a turbocharger. The model of this system is based on physical laws for some parts of the engine such as cylinders, manifolds, turbocharger and crank-slider system. In order to reduce computing time we choose to model heat transfer and heat release during combustion using simple empirical correlations. Resulting model has been implemented in the Matlab-Simulink environment and it can predict variables of interest for control purpose with one degree crank angle resolution. The model has been tested numerically and compared with an industrial engine simulation code with good results. Moreover, model output variables are in good agreement with experimental data recorded on a heavy-duty research engine. The engine model has been embedded on a board providing enough computing performances to perform real-time simulations, this will be helpful for 'hardware-in-the-loop' simulations. Another part of this study is dedicated to the combustion process modelling using a non linear phenomenological model: the NARMAX model. The goal is to predict the in-cylinder pressure evolution using other measurements available on the engine. The NARMAX model parameters have been identified using input-output data carried out from the experimental engine. Such model is well suited for real-time applications compare to numerically cost effective physical

  5. Control and diagnosis oriented modelling of the compression ignition engine; Modelisation du moteur a allumage par compression dans la perspective du controle et du diagnostic

    Energy Technology Data Exchange (ETDEWEB)

    Grondin, O.

    2004-12-15

    This thesis has described an investigation into the modelling of compression ignition engine for control and diagnosis purpose. The Diesel engine is the most efficient and clean internal combustion engine due to modem electromechanical actuators. However, pollutant emission regulations are much more stricter, thus, these complex systems need sophisticated and efficient control algorithms to reach very low emission levels. For this task, engine models are required at each step of the control system development: control laws synthesis, simulation and validation. The system under study is a six cylinder direct injection Diesel engine fitted with a turbocharger. The model of this system is based on physical laws for some parts of the engine such as cylinders, manifolds, turbocharger and crank-slider system. In order to reduce computing time we choose to model heat transfer and heat release during combustion using simple empirical correlations. Resulting model has been implemented in the Matlab-Simulink environment and it can predict variables of interest for control purpose with one degree crank angle resolution. The model has been tested numerically and compared with an industrial engine simulation code with good results. Moreover, model output variables are in good agreement with experimental data recorded on a heavy-duty research engine. The engine model has been embedded on a board providing enough computing performances to perform real-time simulations, this will be helpful for 'hardware-in-the-loop' simulations. Another part of this study is dedicated to the combustion process modelling using a non linear phenomenological model: the NARMAX model. The goal is to predict the in-cylinder pressure evolution using other measurements available on the engine. The NARMAX model parameters have been identified using input-output data carried out from the experimental engine. Such model is well suited for real-time applications compare to numerically cost

  6. Le chomage endemique: un effet dysfonctionnel du modele ivoirien ...

    African Journals Online (AJOL)

    ... de l'action des différents gouvernements qui se sont succédés et contrarient leur projet d'assurer le plein-emploi. Mots-clés: Crise de l'emploi ; Chômage ; Côte d'Ivoire ; miracle ivoirien ; Economie-politique de la Côte d'Ivoire. English Title: Endemic unemployment: a dysfunctional effect of the Ivoirian Development Model.

  7. Large scale model testing

    International Nuclear Information System (INIS)

    Brumovsky, M.; Filip, R.; Polachova, H.; Stepanek, S.

    1989-01-01

    Fracture mechanics and fatigue calculations for WWER reactor pressure vessels were checked by large scale model testing performed using large testing machine ZZ 8000 (with a maximum load of 80 MN) at the SKODA WORKS. The results are described from testing the material resistance to fracture (non-ductile). The testing included the base materials and welded joints. The rated specimen thickness was 150 mm with defects of a depth between 15 and 100 mm. The results are also presented of nozzles of 850 mm inner diameter in a scale of 1:3; static, cyclic, and dynamic tests were performed without and with surface defects (15, 30 and 45 mm deep). During cyclic tests the crack growth rate in the elastic-plastic region was also determined. (author). 6 figs., 2 tabs., 5 refs

  8. Acceptabilité du test VIH proposé aux nourrissons dans les services ...

    African Journals Online (AJOL)

    Maxime Oga

    4 août 2014 ... pesée ou consultation de pédiatrie générale dans l'un des centres de ... du primaire (19 me`res) au secondaire (premier cycle, 9 me`res),. (second cycle, 7 .... et/ou d'attendre son avis pour la réalisation du soin qu'exige le diagnostic. ..... et les médecins les suivent pour leur bonne santé. » FA 116,. 31 ans ...

  9. Testing the standard model

    International Nuclear Information System (INIS)

    Gordon, H.; Marciano, W.; Williams, H.H.

    1982-01-01

    We summarize here the results of the standard model group which has studied the ways in which different facilities may be used to test in detail what we now call the standard model, that is SU/sub c/(3) x SU(2) x U(1). The topics considered are: W +- , Z 0 mass, width; sin 2 theta/sub W/ and neutral current couplings; W + W - , Wγ; Higgs; QCD; toponium and naked quarks; glueballs; mixing angles; and heavy ions

  10. Wave Reflection Model Tests

    DEFF Research Database (Denmark)

    Burcharth, H. F.; Larsen, Brian Juul

    The investigation concerns the design of a new internal breakwater in the main port of Ibiza. The objective of the model tests was in the first hand to optimize the cross section to make the wave reflection low enough to ensure that unacceptable wave agitation will not occur in the port. Secondly...

  11. Testing the Standard Model

    CERN Document Server

    Riles, K

    1998-01-01

    The Large Electron Project (LEP) accelerator near Geneva, more than any other instrument, has rigorously tested the predictions of the Standard Model of elementary particles. LEP measurements have probed the theory from many different directions and, so far, the Standard Model has prevailed. The rigour of these tests has allowed LEP physicists to determine unequivocally the number of fundamental 'generations' of elementary particles. These tests also allowed physicists to ascertain the mass of the top quark in advance of its discovery. Recent increases in the accelerator's energy allow new measurements to be undertaken, measurements that may uncover directly or indirectly the long-sought Higgs particle, believed to impart mass to all other particles.

  12. Summary of the Blind Test Campaign to predict the High Reynolds number performance of DU00-W-210 airfoil

    DEFF Research Database (Denmark)

    Yilmaz, Özlem Ceyhan; Pires, Oscar; Munduate, Xabier

    2017-01-01

    This paper summarizes the results of a blind test campaign organized in the AVATAR project to predict the high Reynolds number performance of a wind turbine airfoil for wind turbine applications. The DU00-W-210 airfoil was tested in the DNW-HDG pressurized wind tunnel in order to investigate...... the flow at high Reynolds number range from 3 to 15 million which is the operating condition of the future large 10MW+ offshore wind turbine rotors. The results of the experiment was used in a blind test campaign to test the prediction capability of the CFD tools used in the wind turbine rotor simulations....... As a result of the blind test campaign it was found that although the codes are in general capable of predicting increased max lift and decreased minimum drag with Re number, the Re trend predictions in particular the glide ratio (lift over drag) need further improvement. In addition to that, the significant...

  13. Radiation Belt Test Model

    Science.gov (United States)

    Freeman, John W.

    2000-10-01

    Rice University has developed a dynamic model of the Earth's radiation belts based on real-time data driven boundary conditions and full adiabaticity. The Radiation Belt Test Model (RBTM) successfully replicates the major features of storm-time behavior of energetic electrons: sudden commencement induced main phase dropout and recovery phase enhancement. It is the only known model to accomplish the latter. The RBTM shows the extent to which new energetic electrons introduced to the magnetosphere near the geostationary orbit drift inward due to relaxation of the magnetic field. It also shows the effects of substorm related rapid motion of magnetotail field lines for which the 3rd adiabatic invariant is violated. The radial extent of this violation is seen to be sharply delineated to a region outside of 5Re, although this distance is determined by the Hilmer-Voigt magnetic field model used by the RBTM. The RBTM appears to provide an excellent platform on which to build parameterized refinements to compensate for unknown acceleration processes inside 5Re where adiabaticity is seen to hold. Moreover, built within the framework of the MSFM, it offers the prospect of an operational forecast model for MeV electrons.

  14. Validation through model testing

    International Nuclear Information System (INIS)

    1995-01-01

    Geoval-94 is the third Geoval symposium arranged jointly by the OECD/NEA and the Swedish Nuclear Power Inspectorate. Earlier symposia in this series took place in 1987 and 1990. In many countries, the ongoing programmes to site and construct deep geological repositories for high and intermediate level nuclear waste are close to realization. A number of studies demonstrates the potential barrier function of the geosphere, but also that there are many unresolved issues. A key to these problems are the possibilities to gain knowledge by model testing with experiments and to increase confidence in models used for prediction. The sessions cover conclusions from the INTRAVAL-project, experiences from integrated experimental programs and underground research laboratories as well as the integration between performance assessment and site characterisation. Technical issues ranging from waste and buffer interactions with the rock to radionuclide migration in different geological media is addressed. (J.S.)

  15. 20 fevrier 2012 - Le Vice-Président du Gouvernement Wallon et Ministre du Développement durable et de la Fonction Publique en charge de l’Energie du Logement et de la Recherche J.-M. Nollet, Royaume de Belgique, visite la salle de contrôle de CMS au Point 5, la caverne expérimentale CMS et le hall de tests des aimants supraconducteurs du LHC. Les chefs de département T. Lagrange et F. Hemmer accompagnent la délégation. L. Walckiers guide la visite SM18.

    CERN Multimedia

    Maximilien Brice

    2012-01-01

    20 fevrier 2012 - Le Vice-Président du Gouvernement Wallon et Ministre du Développement durable et de la Fonction Publique en charge de l’Energie du Logement et de la Recherche J.-M. Nollet, Royaume de Belgique, visite la salle de contrôle de CMS au Point 5, la caverne expérimentale CMS et le hall de tests des aimants supraconducteurs du LHC. Les chefs de département T. Lagrange et F. Hemmer accompagnent la délégation. L. Walckiers guide la visite SM18.

  16. Test du Modèle Standard à basse énergie

    CERN Document Server

    Bey, Anissa

    Precise measurements of Fermi superallowed $0^{+} \\rightarrow 0^{+} \\beta$-decays provide a powerful tool to study the weak interaction properties in the framework of the Standard Model (SM). Collectively, the comparative half-lives (ƒt) of these transitions allow a sensitive probe of the CVC hypothesis and contribute to the most demanding test of the unitarity of the quarks-mixing CKM matrix top-row, by providing, so far, the most accurate determination of its dominant element (Vud). Until recently, an apparent departure from unity enhanced a doubt on the validity of the minimal SM and thus stimulated a considerable effort in order to extend the study to other Fermi emitters available. The$^{62}$Ga and $^{38}$Ca are among key nuclei to achieve these precision tests and verify the reliability of the corrections applied to the experimental ƒt-values. The $^ {62}$Ga $\\beta$-decay was investigated at the IGISOL separator in Jyväskylä, with an experimental setup composed of 3 EUROBALL Clovers for $\\gamma$-ray...

  17. Joining the Dots: Theoretically Connecting the Vona du Toit Model of Creative Ability (VdTMoCA) with Supported Employment

    OpenAIRE

    de Bruyn, Marna; Wright, Jon

    2017-01-01

    The Vona du Toit Model of Creative Ability (VdTMoCA) presents a framework for understanding client motivation and action in occupational therapy, emphasising the relationship between motivation and action. Similarly, motivation to work is regarded as the primary and in some instances, the only eligibility criterion for inclusion in supported employment services. This commentary explores the potential theoretical link between the VdTMoCA and supported employment, primarily applied to the South...

  18. Thermodynamic analysis and modeling of thermo compressor; Analyse et modelisation thermodynamique du mouvement du piston d'un thermocompresseur

    Energy Technology Data Exchange (ETDEWEB)

    Arques, Ph. [Ecole Centrale de Lyon, 69 - Ecully (France)

    1998-07-01

    A thermo-compressor is a compressor that transforms directly the heat release by a source in an energy of pressure without intermediate mechanical work. It is a conversion of the Stirling engine in driven machine in order that the piston that provides the work has been suppressed. In this article, we present the analytical and numerical analyses of heat and mass transfers modeling in the different volumes of the thermo-compressor. This engine comprises a free piston displacer that separates cold and hot gas. (author)

  19. A Mathematical model for gastrointestinal tract dosimetry, and its application to adults; Modele mathematique destine a la dosimetrie du tractus gastrointestinal - application a l'adulte

    Energy Technology Data Exchange (ETDEWEB)

    Vacca, G; Bazin, J P; Karhausen, L [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1969-07-01

    A new method is proposed for the computation of the dose delivered to any level of the gastrointestinal tract after ingestion of radioactive substances. The same method is used as that proposed by ICRP. The concentration of the radionuclide during the progression of the meal is the central concept of this model. A graph relates the MPC with the radioactive half life of the radionuclide and with any level of the gastrointestinal tract of adults.Soluble and insoluble radionuclides are considered. The case of daughter products is discussed in the Appendix. (author) [French] Une methode nouvelle permet le calcul de la dose delivree a un niveau quelconque du tractus gastrointestinal apres ingestion de substances radioactives. Elle utilise d une part la technique de calcul proposee par l'ICRP et de l'autre la notion de concentration du radionuclide au cours de la progression du repas. Un graphique simple met en relation la valeur de la concentration maximale admissible avec la periode radioactive du radionuclide et le niveau considere du tractus gastrointestinal de l'adulte. Le cas d'un radionuclide soluble et celui d'un radionuclide insoluble sont envisages. Un appendice traite le cas des filiations. (auteur)

  20. A Mathematical model for gastrointestinal tract dosimetry, and its application to adults; Modele mathematique destine a la dosimetrie du tractus gastrointestinal - application a l'adulte

    Energy Technology Data Exchange (ETDEWEB)

    Vacca, G.; Bazin, J.P.; Karhausen, L. [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1969-07-01

    A new method is proposed for the computation of the dose delivered to any level of the gastrointestinal tract after ingestion of radioactive substances. The same method is used as that proposed by ICRP. The concentration of the radionuclide during the progression of the meal is the central concept of this model. A graph relates the MPC with the radioactive half life of the radionuclide and with any level of the gastrointestinal tract of adults.Soluble and insoluble radionuclides are considered. The case of daughter products is discussed in the Appendix. (author) [French] Une methode nouvelle permet le calcul de la dose delivree a un niveau quelconque du tractus gastrointestinal apres ingestion de substances radioactives. Elle utilise d une part la technique de calcul proposee par l'ICRP et de l'autre la notion de concentration du radionuclide au cours de la progression du repas. Un graphique simple met en relation la valeur de la concentration maximale admissible avec la periode radioactive du radionuclide et le niveau considere du tractus gastrointestinal de l'adulte. Le cas d'un radionuclide soluble et celui d'un radionuclide insoluble sont envisages. Un appendice traite le cas des filiations. (auteur)

  1. Model-based security testing

    OpenAIRE

    Schieferdecker, Ina; Großmann, Jürgen; Schneider, Martin

    2012-01-01

    Security testing aims at validating software system requirements related to security properties like confidentiality, integrity, authentication, authorization, availability, and non-repudiation. Although security testing techniques are available for many years, there has been little approaches that allow for specification of test cases at a higher level of abstraction, for enabling guidance on test identification and specification as well as for automated test generation. Model-based security...

  2. Model-Based Security Testing

    Directory of Open Access Journals (Sweden)

    Ina Schieferdecker

    2012-02-01

    Full Text Available Security testing aims at validating software system requirements related to security properties like confidentiality, integrity, authentication, authorization, availability, and non-repudiation. Although security testing techniques are available for many years, there has been little approaches that allow for specification of test cases at a higher level of abstraction, for enabling guidance on test identification and specification as well as for automated test generation. Model-based security testing (MBST is a relatively new field and especially dedicated to the systematic and efficient specification and documentation of security test objectives, security test cases and test suites, as well as to their automated or semi-automated generation. In particular, the combination of security modelling and test generation approaches is still a challenge in research and of high interest for industrial applications. MBST includes e.g. security functional testing, model-based fuzzing, risk- and threat-oriented testing, and the usage of security test patterns. This paper provides a survey on MBST techniques and the related models as well as samples of new methods and tools that are under development in the European ITEA2-project DIAMONDS.

  3. Creep of uranium dioxide: bending test and mechanical behaviour; Etude du fluage du dioxyde d'uranium: caracterisation par essais de flexion et modelisation mecanique

    Energy Technology Data Exchange (ETDEWEB)

    Colin, Ch

    2003-09-01

    has been modeled. The introduction of internal variables in a law describing a kinematic hardening of the material allowed the first two stages of creep and the recovery phenomena observed during partial un-loadings to be described. The identification was realized by inverse method, coupling an optimization of the parameters with a finite element calculation of the deformation of the bending specimen. The application of this model to simulate a transient power ramp demonstrated that the expected stress relaxation in the fuel does not prevent a radial break of pellet at the end of the power increase. During a maintain at high power, the high temperature in the core of the pellet allows a stress relaxation, especially close from the hollows. That results in a flow of the ceramic, mainly axial, that is clearly confirmed by the observation of used pellets. A final application of our experimental device consisted in testing ion-irradiated specimens, with a 50 {mu}m penetration depth. The small thickness of our samples allows the effect of an irradiation on the creep of UO{sub 2} to be revealed. (author)

  4. Study of the permeability up-scaling by direct filtering of geostatistical model; Etude du changement d'echelle des permeabilites par filtrage direct du modele geostatistique

    Energy Technology Data Exchange (ETDEWEB)

    Zargar, G

    2005-10-15

    In this thesis, we present a new approach, which consists in directly up-scaling the geostatistical permeability distribution rather than the individual realizations. Practically, filtering techniques based on. the FFT (Fast Fourier Transform), allows us to generate geostatistical images, which sample the up-scaled distributions. In the log normal case, an equivalence hydraulic criterion is proposed, allowing to re-estimate the geometric mean of the permeabilities. In the anisotropic case, the effective geometric mean becomes a tensor which depends on the level of filtering used and it can be calculated by a method of renormalisation. Then, the method was generalized for the categorial model. Numerical tests of the method were set up for isotropic, anisotropic and categorial models, which shows good agreement with theory. (author)

  5. Study of the permeability up-scaling by direct filtering of geostatistical model; Etude du changement d'echelle des permeabilites par filtrage direct du modele geostatistique

    Energy Technology Data Exchange (ETDEWEB)

    Zargar, G.

    2005-10-15

    In this thesis, we present a new approach, which consists in directly up-scaling the geostatistical permeability distribution rather than the individual realizations. Practically, filtering techniques based on. the FFT (Fast Fourier Transform), allows us to generate geostatistical images, which sample the up-scaled distributions. In the log normal case, an equivalence hydraulic criterion is proposed, allowing to re-estimate the geometric mean of the permeabilities. In the anisotropic case, the effective geometric mean becomes a tensor which depends on the level of filtering used and it can be calculated by a method of renormalisation. Then, the method was generalized for the categorial model. Numerical tests of the method were set up for isotropic, anisotropic and categorial models, which shows good agreement with theory. (author)

  6. Modelling the pile load test

    Directory of Open Access Journals (Sweden)

    Prekop Ľubomír

    2017-01-01

    Full Text Available This paper deals with the modelling of the load test of horizontal resistance of reinforced concrete piles. The pile belongs to group of piles with reinforced concrete heads. The head is pressed with steel arches of a bridge on motorway D1 Jablonov - Studenec. Pile model was created in ANSYS with several models of foundation having properties found out from geotechnical survey. Finally some crucial results obtained from computer models are presented and compared with these obtained from experiment.

  7. Modelling the pile load test

    OpenAIRE

    Prekop Ľubomír

    2017-01-01

    This paper deals with the modelling of the load test of horizontal resistance of reinforced concrete piles. The pile belongs to group of piles with reinforced concrete heads. The head is pressed with steel arches of a bridge on motorway D1 Jablonov - Studenec. Pile model was created in ANSYS with several models of foundation having properties found out from geotechnical survey. Finally some crucial results obtained from computer models are presented and compared with these obtained from exper...

  8. Tests of the scalar sector of the electroweak theory; Tests du secteur scalaire de la theorie electrofaible

    Energy Technology Data Exchange (ETDEWEB)

    Chopin, E. [Grenoble-1 Univ., 74 - Annecy (France). Lab. de Physique des Particules Elementaires]|[Savoie Univ., 73 - Chambery (France)

    1996-12-13

    The theory of weak interactions contains an important question: why are the gauge bosons (W{sup +-} and Z) massive particles? Several models exist that may explain this experimental fact, and these models may also have some experimental consequences. We thus have studied the implications of some models beyond the Standard Model in the Z -> {gamma}{gamma}{gamma} decay. The simplest model explaining the W and the Z mass contains a scalar particle called the Higgs boson, and some future colliders will try to discover this particle. However, this won't be sufficient to understand the mechanism that makes the W and the Z massive. Among the interactions needed to realize this spontaneous symmetry breakdown, there exist some interactions between several Higgs bosons. It is therefore needed to measure the corresponding couplings. We have shown that the triple-Higgs interaction is reasonably measurable in the next e{sup +} e{sup -} linear collider (in the TeV range). In order to get this result, we had to complete a thorough phenomenological study of some decay processes. {gamma}{gamma} {yields} W{sup +}W{sup -}HH and e{sup +}e{sup -} {yields} {nu}{sub e}{nu}-bar{sub e}HH were the most interesting processes. For the purpose of this study, we used some new gauges derived from some background filed gauges that were shown to be quite interesting. The use of some structure functions was shown to be a powerful way to reproduce the exact computations, and pointed out the dominance of longitudinal W fusion in the latter processes. We tried to improve the structure function formalism, and we have shown the limitations of validity for this formalism. (author)

  9. Test du modèle du "Petit Higgs" dans ATLAS au LHC, et simulation de la numérisation du calorimètre électromagnétique

    CERN Document Server

    Lechowski, Matthieu

    2005-01-01

    LHC is a proton-proton collider with an energy of 14 TeV in the center of mass, which will start in 2007 at CERN. Two of its experiments, ATLAS, and CMS, will search and study in particular the Higgs boson, Supersymmetry and other new Physics. This thesis was about two aspects of the ATLAS experiment : â on one hand the simulation of the liquid Argon electromagnetic calorimeter, with the emulation of the electronic chain in charge of the digitization of the signal and also the evaluation of the electronic noise and the pile-up noise (coming from minimum bias events at LHC). These two points have been validated by the analysis of the data taken during beam tests in 2002 and 2004. â on the other hand, a physics study concerning the Little Higgs model. This recent model solves the hierarchy problem of the Standard Model, in introducing new heavy particles to cancel quadratic divergences arising in the calculation of the Higgs boson mass. These new particles, with a mass about the TeV/c2, are one heavy quark to...

  10. Methods for testing transport models

    International Nuclear Information System (INIS)

    Singer, C.; Cox, D.

    1991-01-01

    Substantial progress has been made over the past year on six aspects of the work supported by this grant. As a result, we have in hand for the first time a fairly complete set of transport models and improved statistical methods for testing them against large databases. We also have initial results of such tests. These results indicate that careful application of presently available transport theories can reasonably well produce a remarkably wide variety of tokamak data

  11. The role of Rad 51 protein in radioresistance of spheroid model of Du 145 prostate carcinoma cell line

    International Nuclear Information System (INIS)

    Taghizadeh, M.; Khoei, S.; Nikoofar, A. R.; Ghamsari, L.; Goliaei, B.

    2009-01-01

    Rad 51 is a protein with critical role in double strand break repair. Down-regulation of this protein has a significant effect in radiosensitivity of some cell lines like prostate carcinoma. Compared to monolayer cell culture model, the spheroids are more resistant to radiation. The aim of the current study was to determine the Rad 51 protein level in Du 145 spheroids, and monolayer cells before and after exposure to gamma irradiation. Materials and Methods: In the present study, western blot was used to determine the level of Rad 51 protein in Du 145 cell line grown as monolayer and spheroid. Results: Western blot analysis showed that in the spheroid cells, Rad 51 had an elevated level before and after radiation in comparison with monolayer cells. Higher doses of radiation induced elevated expression of Rad 51 protein in both culture models.The level of at protein after exposure to gamma rays had been time-dependent. Conclusion: Rad 51 might act as a mediator of radiation resistance in tumor cells. Repression of Rad 51 activity could be a prominent strategy to overcome radiation resistance of tumors.

  12. 12th Rencontres du Vietnam : High Sensitivity Experiments Beyond the Standard Model

    CERN Document Server

    2016-01-01

    The goal of this workshop is to gather researchers, theoreticians, experimentalists and young scientists searching for physics beyond the Standard Model of particle physics using high sensitivity experiments. The standard model has been very successful in describing the particle physics world; the Higgs-Englert-Brout boson discovery is its last major discovery. Complementary to the high energy frontier explored at colliders, real opportunities for discovery exist at the precision frontier, testing fundamental symmetries and tracking small SM deviations.

  13. NET model coil test possibilities

    International Nuclear Information System (INIS)

    Erb, J.; Gruenhagen, A.; Herz, W.; Jentzsch, K.; Komarek, P.; Lotz, E.; Malang, S.; Maurer, W.; Noether, G.; Ulbricht, A.; Vogt, A.; Zahn, G.; Horvath, I.; Kwasnitza, K.; Marinucci, C.; Pasztor, G.; Sborchia, C.; Weymuth, P.; Peters, A.; Roeterdink, A.

    1987-11-01

    A single full size coil for NET/INTOR represents an investment of the order of 40 MUC (Million Unit Costs). Before such an amount of money or even more for the 16 TF coils is invested as much risks as possible must be eliminated by a comprehensive development programme. In the course of such a programme a coil technology verification test should finally prove the feasibility of NET/INTOR TF coils. This study report is almost exclusively dealing with such a verification test by model coil testing. These coils will be built out of two Nb 3 Sn-conductors based on two concepts already under development and investigation. Two possible coil arrangements are discussed: A cluster facility, where two model coils out of the two Nb 3 TF-conductors are used, and the already tested LCT-coils producing a background field. A solenoid arrangement, where in addition to the two TF model coils another model coil out of a PF-conductor for the central PF-coils of NET/INTOR is used instead of LCT background coils. Technical advantages and disadvantages are worked out in order to compare and judge both facilities. Costs estimates and the time schedules broaden the base for a decision about the realisation of such a facility. (orig.) [de

  14. Collaborative testing of turbulence models

    Science.gov (United States)

    Bradshaw, P.

    1992-12-01

    This project, funded by AFOSR, ARO, NASA, and ONR, was run by the writer with Profs. Brian E. Launder, University of Manchester, England, and John L. Lumley, Cornell University. Statistical data on turbulent flows, from lab. experiments and simulations, were circulated to modelers throughout the world. This is the first large-scale project of its kind to use simulation data. The modelers returned their predictions to Stanford, for distribution to all modelers and to additional participants ('experimenters')--over 100 in all. The object was to obtain a consensus on the capabilities of present-day turbulence models and identify which types most deserve future support. This was not completely achieved, mainly because not enough modelers could produce results for enough test cases within the duration of the project. However, a clear picture of the capabilities of various modeling groups has appeared, and the interaction has been helpful to the modelers. The results support the view that Reynolds-stress transport models are the most accurate.

  15. Concetration and Distribution of Depleted Uranium (DU) and Beryllium (Be) in Soil and Air on Illeginni Island at Kwajalein Atoll after the Final Land-Impact Test

    Energy Technology Data Exchange (ETDEWEB)

    Robison, W L; Hamilton, T F; Martinelli, R E; Gouveia, F J; Kehl, S R; Lindman, T R; Yakuma, S C

    2010-04-22

    Re-entry vehicles on missiles launched from Vandenberg Air Force base in California re-enter at the Western Test Range, the Regan Test Site (RTS) at Kwajalein Atoll. An Environmental Assessment (EA) was written at the beginning of the program to assess potential impact of DU and Be, the major RV materials of interest from a health and environmental perspective, for both ocean and land impacts. The chemical and structural form of Be and DU in RVs is such that they are insoluble in soil water and seawater. Thus, they are not toxic to plant life on the isalnd (no soil to plant uptake.) Similarly, due to their insolubility in sea water there is no uptake of either element by fish, mollusks, shellfish, sea mammals, etc. No increase in either element has been observed in sea life around Illeginnin Island where deposition of DU and Be has occured. The critical terrestrial exposure pathway for U and Be is inhalation. Concentration of both elements in air over the test period (1989 to 2006) is lower by a factor of nearly 10,000 than the most restrictive U.S. guideline for the general public. Uranium concentrations in air are also lower by factors of 10 to 100 than concentrations of U in air in the U.S. measured by the EPA (Keith et al., 1999). U and Be concentrations in air downwind of deposition areas on Illeginni Island are essentially indistinguishable from natural background concentrations of U in air at the atolls. Thus, there are no health related issues associated with people using the island.

  16. Concetration and Distribution of Depleted Uranium (DU) and Beryllium (Be) in Soil and Air on Illeginni Island at Kwajalein Atoll after the Final Land-Impact Test

    International Nuclear Information System (INIS)

    Robison, W.L.; Hamilton, T.F.; Martinelli, R.E.; Gouveia, F.J.; Kehl, S.R.; Lindman, T.R.; Yakuma, S.C.

    2010-01-01

    Re-entry vehicles on missiles launched from Vandenberg Air Force base in California re-enter at the Western Test Range, the Regan Test Site (RTS) at Kwajalein Atoll. An Environmental Assessment (EA) was written at the beginning of the program to assess potential impact of DU and Be, the major RV materials of interest from a health and environmental perspective, for both ocean and land impacts. The chemical and structural form of Be and DU in RVs is such that they are insoluble in soil water and seawater. Thus, they are not toxic to plant life on the isalnd (no soil to plant uptake.) Similarly, due to their insolubility in sea water there is no uptake of either element by fish, mollusks, shellfish, sea mammals, etc. No increase in either element has been observed in sea life around Illeginnin Island where deposition of DU and Be has occured. The critical terrestrial exposure pathway for U and Be is inhalation. Concentration of both elements in air over the test period (1989 to 2006) is lower by a factor of nearly 10,000 than the most restrictive U.S. guideline for the general public. Uranium concentrations in air are also lower by factors of 10 to 100 than concentrations of U in air in the U.S. measured by the EPA (Keith et al., 1999). U and Be concentrations in air downwind of deposition areas on Illeginni Island are essentially indistinguishable from natural background concentrations of U in air at the atolls. Thus, there are no health related issues associated with people using the island.

  17. Determination du niveau d'anticorps antitetaniques en donneurs de sang au moyen du test ELISA-TÉTANOS (São Paulo, SP, Bresil

    Directory of Open Access Journals (Sweden)

    Luzia Cristina Contim Ferrato

    1990-12-01

    Full Text Available Le test ELISA-TÉTANOS (Biosys, France a été utilisé pour le titrage des anti-corps tétaniques (sensibilité = 0,0025 UI/ml en sérums humains de donneurs de sang, 566 hommes et 108 femmes, âges de 18 à 58 ans, moyenne de 29 ans, provenant de São Paulo, SP, Brésil. L'OMS, acceptant seulement la séroneutralisation sur souris (NT, la méthode de référence, pour les études sur la protection contre le tétanos, préconise le titre de 0,01 UI/ml comme minimum protecteur. BOURLEAUD & HUET ont proposé la limite de 0,06 UI/ml quand s'emploie le test ELISA, en attendant à une certaine discordance inévitable entre les méthodes. Parmi les 674 sérums étudiés, 178 (26,41% n'ont pas présenté d'anticorps ( 0,06 UI/ml.

  18. Methods for testing transport models

    International Nuclear Information System (INIS)

    Singer, C.; Cox, D.

    1993-01-01

    This report documents progress to date under a three-year contract for developing ''Methods for Testing Transport Models.'' The work described includes (1) choice of best methods for producing ''code emulators'' for analysis of very large global energy confinement databases, (2) recent applications of stratified regressions for treating individual measurement errors as well as calibration/modeling errors randomly distributed across various tokamaks, (3) Bayesian methods for utilizing prior information due to previous empirical and/or theoretical analyses, (4) extension of code emulator methodology to profile data, (5) application of nonlinear least squares estimators to simulation of profile data, (6) development of more sophisticated statistical methods for handling profile data, (7) acquisition of a much larger experimental database, and (8) extensive exploratory simulation work on a large variety of discharges using recently improved models for transport theories and boundary conditions. From all of this work, it has been possible to define a complete methodology for testing new sets of reference transport models against much larger multi-institutional databases

  19. Simulation of recent and future climates using CNRM and IPSL models; Simulation du climat recent et futur par les modeles du CNRM et de l'IPSL

    Energy Technology Data Exchange (ETDEWEB)

    Dufresne, J.L.; Bony, S.; Fairhead, L.; Grandpeix, J.Y.; Hourdin, F.; Idelkadi, A.; Musat, I. [Universite Pierre et Marie Curie, Lab. de Meteorologie Dynamique (LMD-IPSL), CNRS, 75 - Paris (France); Salas y Melia, D.; Tyteca, S.; Chauvin, F.; Deque, M.; Douville, H.; Gueremy, J.F.; Marquet, P.; Planton, S.; Royer, J.F.; Voldoire, A. [Meteo France Centre National de Recherches Meteorologiques, 31 - Toulouse (France); Denvil, S.; Cadule, P.; Foujols, M.A. [Universite Pierre et Marie Curie, Institut Pierre-Simon Laplace, CNRS, 75 - Paris (France); Arzel, O.; Fichefet, T. [Universite Catholique de Louvain (UCL), Louvain-la-Neuve (Belgium). Inst. d' Astronomie et de Geophysique G. Lemaitre; Braconnot, P.; Brockmann, P.; Caubel, A.; Friedlingstein, P.; Marti, O.; Swingedouw, D. [Laboratoire des Sciences du Climat et de l' Environnement, Domaine du CNRS, 91 - Gif Sur Yvette (France); Krinner, G. [Universite Joseph-Fourier, Grenoble I, Lab. de Glaciologie et Geophysique de l' Environnement (LGGE), CNRS, 38 - Saint Martin d' Heres (France); Levy, C.; Madec, G. [Universite Pierre et Marie Curie, Lab. d' Oceanographie et Climat (Locean-IPLS), CNRS, 75 - Paris (France)

    2006-11-15

    In support of the Fourth Assessment Report of the Intergovernmental Panel on Climate Change (IPCC) that should appear in early 2007, modelling groups world-wide have performed a huge coordinated exercise of climate change runs for the 20. and 21. centuries. In this paper we present the results of the two French climate models, CNRM and IPSL. In particular we emphasize the progress made since the previous IPCC report and we identify which results are comparable among models and which strongly differ. (authors)

  20. Large-scale column experiment: study of CO{sub 2}, pore water rock reactions and model test case; Experimentation de longue duree sur grandes colonnes, dans le contexte du stockage geologique de CO{sub 2}: etude des interactions eau-roche et modelisation

    Energy Technology Data Exchange (ETDEWEB)

    Bateman, K.; Turner, G.; Pearce, J.M.; Noy, D.J.; Birchall, D.; Rochelle, C.A. [British Geological Survey, Kingsley Dunham Centre, Keyworth (United Kingdom)

    2005-07-01

    During underground carbon dioxide (CO{sub 2}) storage operations in deep reservoirs, the CO{sub 2} can be trapped in three ways; - as 'free' CO{sub 2}, most likely as a supercritical phase (physical trapping); - dissolved in formation water (hydrodynamic trapping); - precipitated in carbonate phases such as calcite (mineral trapping). This study focuses on the reactions between CO{sub 2}, pore-water and host rock. The aim of this work was to provide a well-constrained long-term laboratory experiment reacting known quantities of minerals with CO{sub 2}-rich fluids, in order to try and represent situations where CO{sub 2} is being injected into lithologies deep underground. The experimental results can then be used as a test case with which to help validate predictive geochemical computer models. These will help improve our ability to predict the long-term fate of carbon dioxide (CO{sub 2}) stored underground. The experiment, though complex in terms of equipment, ran for approximately 7.5 months. The reacted material was then examined for mineralogical changes and the collected fluids analysed to provide data on the fate of the dissolved species. Changes were readily observable on the carbonates present in the starting material, which matches well with the observed trends in the fluid chemistry. However, although changes in silica concentrations were seen in the fluid chemistry no evidence for pitting or etching was noted in the silica bearing phases. Modelling of the experimental systems was performed using the BGS coupled code, PRECIP. As a general conclusion, the model predictions tend to over estimate the degree of reaction compared with the results from the experiment. In particular, some mineral phases (e.g. dawsonite) that are predicted to form in large quantities by the model are not seen at all in the experimental system. The differences between the model predictions and the experimental observations highlight the need for thermodynamic and kinetic

  1. Economic consequences of the Swiss 'Sortir du nucleaire' and 'Moratoire-plus' popular initiatives - Analysis using a balanced model

    International Nuclear Information System (INIS)

    Mueller, A.; Wickart, M.; Van Nieuwkoop, R.

    2001-01-01

    This article is a short version of the ENET number 210359. This report for the Swiss Federal Office of Energy (SFOE) presents the results of a study made to assess the economic consequences of two models for the opting out of nuclear energy in Switzerland, as proposed in two popular initiatives. The 'Sortir du nucleaire' (electricity without atomic power) initiative calls for the shutting down of the existing nuclear power stations and the 'Moratoire-plus' initiative calls for a stop on the building of new atomic power stations for 10 years. The method used for assessing the costs and benefits resulting if the initiatives were accepted in a public vote is described. Basic assumptions made on further factors concerning the electricity and energy markets are discussed. Results of analyses made for various scenarios with respect to CO 2 emissions are presented and include discussions on risk costs, effects on employment and welfare aspects

  2. Tourism potential valorisation of the old town centre in Sombor based on the Hilary Du Cros model

    Directory of Open Access Journals (Sweden)

    Igor Stamenković

    2013-01-01

    Full Text Available Cultural heritage and tourism are interconnected. As the development of tourism contributes to economic development, it is first necessary to perform an adequate valorisation of cultural heritage, in order to create a suitable tourism product. Old town centres as such, are the objects of different activities aimed at its development and adaptation to new trends. In this paper, focus is on the old town centre in Sombor, with an aim to determine its status in the competitive market of cultural tourism, whether it could be an independent motive that could attract potential tourists, as well as to determine the necessary actions needed to improve quality and competitiveness in order bring them to a higher level. With this in mind, this paper deals with the tourism valorisation of the old town centre based on the model of H. Du Cros.

  3. Mechanisms controlling lateral and vertical porewater migration of depleted uranium (DU) at two UK weapons testing sites

    Energy Technology Data Exchange (ETDEWEB)

    Graham, Margaret C., E-mail: Margaret.Graham@ed.ac.uk [School of GeoSciences, Crew Building, University of Edinburgh, The King' s Buildings, West Mains Road, Edinburgh, EH9 3JN (United Kingdom); Oliver, Ian W.; MacKenzie, Angus B.; Ellam, Robert M. [Scottish Universities Environmental Research Centre (SUERC), Rankine Avenue, Scottish Enterprise Technology Park, East Kilbride, G75 0QF (United Kingdom); Farmer, John G. [School of GeoSciences, Crew Building, University of Edinburgh, The King' s Buildings, West Mains Road, Edinburgh, EH9 3JN (United Kingdom)

    2011-04-15

    Uranium associations with colloidal and truly dissolved soil porewater components from two Ministry of Defence Firing Ranges in the UK were investigated. Porewater samples from 2-cm depth intervals for three soil cores from each of the Dundrennan and Eskmeals ranges were fractionated using centrifugal ultrafiltration (UF) and gel electrophoresis (GE). Soil porewaters from a transect running downslope from the Dundrennan firing area towards a stream (Dunrod Burn) were examined similarly. Uranium concentrations and isotopic composition were determined using Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) and Multi-Collector-Inductively Coupled Plasma-Mass Spectrometry (MC-ICP-MS), respectively. The soils at Dundrennan were Fe- and Al-rich clay-loam soils whilst at Eskmeals, they were Fe- and Al-poor sandy soils; both, however, had similar organic matter contents due to the presence of a near-surface peaty layer at Eskmeals. These compositional features influenced the porewater composition and indeed the associations of U (and DU). In general, at Dundrennan, U was split between large (100 kDa-0.2 {mu}m) and small (3-30 kDa) organic colloids whilst at Eskmeals, U was mainly in the small colloidal and truly dissolved fractions. Especially below 10 cm depth, association with large Fe/Al/organic colloids was considered to be a precursor to the removal of U from the Dundrennan porewaters to the solid phase. In contrast, the association of U with small organic colloids was largely responsible for inhibiting attenuation in the Eskmeals soils. Lateral migration of U (and DU) through near-surface Dundrennan soils will involve both large and small colloids but, at depth, transport of the smaller amounts of U remaining in the porewaters may involve large colloids only. For one of the Dundrennan cores the importance of redox-related processes for the re-mobilisation of DU was also indicated as Mn{sup IV} reduction resulted in the release of both Mn{sup II} and U{sup VI

  4. Test model of WWER core

    International Nuclear Information System (INIS)

    Tikhomirov, A. V.; Gorokhov, A. K.

    2007-01-01

    The objective of this paper is creation of precision test model for WWER RP neutron-physics calculations. The model is considered as a tool for verification of deterministic computer codes that enables to reduce conservatism of design calculations and enhance WWER RP competitiveness. Precision calculations were performed using code MCNP5/1/ (Monte Carlo method). Engineering computer package Sapfir 9 5andRC V VER/2/ is used in comparative analysis of the results, it was certified for design calculations of WWER RU neutron-physics characteristic. The object of simulation is the first fuel loading of Volgodon NPP RP. Peculiarities of transition in calculation using MCNP5 from 2D geometry to 3D geometry are shown on the full-scale model. All core components as well as radial and face reflectors, automatic regulation in control and protection system control rod are represented in detail description according to the design. The first stage of application of the model is assessment of accuracy of calculation of the core power. At the second stage control and protection system control rod worth was assessed. Full scale RP representation in calculation using code MCNP5 is time consuming that calls for parallelization of computational problem on multiprocessing computer (Authors)

  5. Model test of boson mappings

    International Nuclear Information System (INIS)

    Navratil, P.; Dobes, J.

    1992-01-01

    Methods of boson mapping are tested in calculations for a simple model system of four protons and four neutrons in single-j distinguishable orbits. Two-body terms in the boson images of the fermion operators are considered. Effects of the seniority v=4 states are thus included. The treatment of unphysical states and the influence of boson space truncation are particularly studied. Both the Dyson boson mapping and the seniority boson mapping as dictated by the similarity transformed Dyson mapping do not seem to be simply amenable to truncation. This situation improves when the one-body form of the seniority image of the quadrupole operator is employed. Truncation of the boson space is addressed by using the effective operator theory with a notable improvement of results

  6. Mechanisms controlling lateral and vertical porewater migration of depleted uranium (DU) at two UK weapons testing sites.

    Science.gov (United States)

    Graham, Margaret C; Oliver, Ian W; MacKenzie, Angus B; Ellam, Robert M; Farmer, John G

    2011-04-15

    Uranium associations with colloidal and truly dissolved soil porewater components from two Ministry of Defence Firing Ranges in the UK were investigated. Porewater samples from 2-cm depth intervals for three soil cores from each of the Dundrennan and Eskmeals ranges were fractionated using centrifugal ultrafiltration (UF) and gel electrophoresis (GE). Soil porewaters from a transect running downslope from the Dundrennan firing area towards a stream (Dunrod Burn) were examined similarly. Uranium concentrations and isotopic composition were determined using Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) and Multi-Collector-Inductively Coupled Plasma-Mass Spectrometry (MC-ICP-MS), respectively. The soils at Dundrennan were Fe- and Al-rich clay-loam soils whilst at Eskmeals, they were Fe- and Al-poor sandy soils; both, however, had similar organic matter contents due to the presence of a near-surface peaty layer at Eskmeals. These compositional features influenced the porewater composition and indeed the associations of U (and DU). In general, at Dundrennan, U was split between large (100kDa-0.2μm) and small (3-30kDa) organic colloids whilst at Eskmeals, U was mainly in the small colloidal and truly dissolved fractions. Especially below 10cm depth, association with large Fe/Al/organic colloids was considered to be a precursor to the removal of U from the Dundrennan porewaters to the solid phase. In contrast, the association of U with small organic colloids was largely responsible for inhibiting attenuation in the Eskmeals soils. Lateral migration of U (and DU) through near-surface Dundrennan soils will involve both large and small colloids but, at depth, transport of the smaller amounts of U remaining in the porewaters may involve large colloids only. For one of the Dundrennan cores the importance of redox-related processes for the re-mobilisation of DU was also indicated as Mn(IV) reduction resulted in the release of both Mn(II) and U(VI) into the truly

  7. A 160 kJ dual plasma focus (DuPF) for fusion-relevant materials testing and nano-materials fabrication

    International Nuclear Information System (INIS)

    Saw, S.H.; Damideh, V.; Chong, P.L.; Lee, Paul; Rawat, R.S.; Lee, Sing

    2014-01-01

    This paper summarizes PF-160 Dual Plasma Focus (DuPF) numerical experiments using the Lee Model code and preliminary 3D design drawings using SolidWorks software. This DuPF consists of two interchangeable electrodes enabling it to be optimized for both Slow Pinch Mode (SFM) and Fast Pinch Mode (FFM); the latter using a speed factor (SF) of 90 kA cm-1 Torr-0.5 for FFM in deuterium [S Lee et al, IEEE Trans Plasma Science 24, 1101-1105 (1996)]; and the former with SF of less than half that value for SFM. Starting with available 6 × 450 µF capacitors rated at 11kV (10% reversal), numerical experiments indicate safe operation at 9 kV, 6 Torr deuterium with FFM anode of 5 cm radius; producing intense ion beam and streaming plasma pulses which would be useful for studies of potential fusion reactor wall materials. On the other hand operating at 5 kV, 10 Torr deuterium with SFM anode of 10 cm radius leads to long-duration, uniform large-area flow which could be more suitable for synthesis of nano-materials. The dual plasma focus design is illustrated here with two figures showing FFM and SFM electrodes. (author)

  8. Methodological developments and qualification of calculation schemes for the modelling of photonic heating in the experimental devices of the future Jules Horowitz material testing reactor (RJH); Developpements methodologiques et qualification de schemas de calcul pour la modelisation des echauffements photoniques dans les dispositifs experimentaux du futur reacteur d'irradiation technologiques Jules Horowitz (RJH)

    Energy Technology Data Exchange (ETDEWEB)

    Blanchet, D

    2006-07-01

    The objective of this work is to develop the modelling of the nuclear heating of the experimental devices of the future Jules Horowitz material testing reactor (RJH). The strong specific nuclear power produced (460 kW/l), induces so intense photonic fluxes which cause heating and large temperature gradients that it is necessary to control it by an adequate design. However, calculations of heating are penalized by the very large uncertainties estimated at a value of about 30% (2*{sigma}) coming from the gaps and uncertainties of the data of gamma emission present in the libraries of basic nuclear data. The experimental program ADAPh aims at reducing these uncertainties. Measurements by thermoluminescent detectors (TLD) and ionisation chambers are carried out in the critical assemblies EOLE (Mox) and Minerve (UO{sub 2}). The rigorous interpretation of these measurements requires specific developments based on Monte-Carlo simulations of coupled neutron-gamma and gamma-electron transport. The developments carried out are made different in particular by the modelling of cavities phenomena and delayed gamma emissions by the decay of fission products. The comparisons calculation-measurement made it possible to identify a systematic bias confirming a tendency of calculations to underestimate measurements. A Bayesian method of adjustment was developed in order to re-estimate the principal components of the gamma heating and to transpose the results obtained to the devices of the RJH, under conditions clearly and definitely representative. This work made possible to reduce significantly the uncertainties on the determination of the gamma heating from 30 to 15 per cent. (author)

  9. Methodological developments and qualification of calculation schemes for the modelling of photonic heating in the experimental devices of the future Jules Horowitz material testing reactor (RJH); Developpements methodologiques et qualification de schemas de calcul pour la modelisation des echauffements photoniques dans les dispositifs experimentaux du futur reacteur d'irradiation technologiques Jules Horowitz (RJH)

    Energy Technology Data Exchange (ETDEWEB)

    Blanchet, D

    2006-07-01

    The objective of this work is to develop the modelling of the nuclear heating of the experimental devices of the future Jules Horowitz material testing reactor (RJH). The strong specific nuclear power produced (460 kW/l), induces so intense photonic fluxes which cause heating and large temperature gradients that it is necessary to control it by an adequate design. However, calculations of heating are penalized by the very large uncertainties estimated at a value of about 30% (2*{sigma}) coming from the gaps and uncertainties of the data of gamma emission present in the libraries of basic nuclear data. The experimental program ADAPh aims at reducing these uncertainties. Measurements by thermoluminescent detectors (TLD) and ionisation chambers are carried out in the critical assemblies EOLE (Mox) and Minerve (UO{sub 2}). The rigorous interpretation of these measurements requires specific developments based on Monte-Carlo simulations of coupled neutron-gamma and gamma-electron transport. The developments carried out are made different in particular by the modelling of cavities phenomena and delayed gamma emissions by the decay of fission products. The comparisons calculation-measurement made it possible to identify a systematic bias confirming a tendency of calculations to underestimate measurements. A Bayesian method of adjustment was developed in order to re-estimate the principal components of the gamma heating and to transpose the results obtained to the devices of the RJH, under conditions clearly and definitely representative. This work made possible to reduce significantly the uncertainties on the determination of the gamma heating from 30 to 15 per cent. (author)

  10. Efficacité relative des grilles de correction d'un test de jugement situationnel pour la sélection du personnel de centres d'appels

    OpenAIRE

    Poirier, Sabrina

    2016-01-01

    Dans le domaine des centres d’appels, l’affectation d’agents au service à la clientèle efficaces et satisfaits représente une activité cruciale pour toute direction dédiée aux ressources humaines de ces unités d’affaires. Or, pour parvenir à prendre de bonnes décisions d’embauche et de rejet, des instruments de mesure et d’évaluation des compétences sont souvent mis à contribution. À cet effet, les tests de jugement situationnel (TJS) sont de plus en plus utilisés pour la sélection du personn...

  11. Model-based testing for software safety

    NARCIS (Netherlands)

    Gurbuz, Havva Gulay; Tekinerdogan, Bedir

    2017-01-01

    Testing safety-critical systems is crucial since a failure or malfunction may result in death or serious injuries to people, equipment, or environment. An important challenge in testing is the derivation of test cases that can identify the potential faults. Model-based testing adopts models of a

  12. 46 CFR 154.431 - Model test.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Model test. 154.431 Section 154.431 Shipping COAST GUARD... Model test. (a) The primary and secondary barrier of a membrane tank, including the corners and joints...(c). (b) Analyzed data of a model test for the primary and secondary barrier of the membrane tank...

  13. 46 CFR 154.449 - Model test.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Model test. 154.449 Section 154.449 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY STANDARDS FOR SELF... § 154.449 Model test. The following analyzed data of a model test of structural elements for independent...

  14. The use of polarized deuterons beams and the determination of the optical model parameters; Utilisation de faisceaux de deutons polarises et determination des parametres du modele optique

    Energy Technology Data Exchange (ETDEWEB)

    Raynal, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-06-15

    entraine des relations entre les parametres adoptes. Les limitations de ces parametres sont etudiees specialement dans le cas d'un faisceau de particules de spin 1 ayant un plan de symetrie. Les reactions nucleaires a deux corps sont decrites dans le formalisme de l'helicite. A l'aide des coefficients de polarisation adoptes, on etudie la polarisation dans l'etat final avec etat initial polarise. Un potentiel optique pour deutons pout comprendre une partie scalaire, un couplage L.S et des potentiels tensoriels formes avec la distance du deuton au noyau, son moment angulaire ou son impulsion relative. Des calculs ont ete faits avec les deux premieres sortes de potentiels tensoriels. Plusieurs auteurs ont calcule un potentiel pour deutons a partir du modele optique nucleon oyau. Ces calculs sont repris en considerant l'onde S et l'onde D du deuton. Les differentes parties du potentiel ont ete calculees avec plusieurs fonctions d'onde intrinseque. L'utilisation de potentiels non uniquement scalaires permet d'obtenir de bons accords pour la section efficace avec des rayons nucleaires plus eleves que ceux necessaires avec un potentiel purement central. Les mesures experimentales de polarisation faites a Saclay pour la diffusion elastique de deutons sur le calcium sont en desaccord avec l'existence d'un potentiel tensoriel important ; elles peuvent etre reproduites en utilisant un couplage L.S. independant du potentiel central, mais avec des rayons tres faibles. (auteur)

  15. Tourism Potential Valorization of the River Danube in Novi Sad and its Environment Based on the Hilary Du Cros Model

    Directory of Open Access Journals (Sweden)

    Milica Pantović

    2013-01-01

    Full Text Available Natural resources are the main basis for tourism development in one region. Given that natural resources are not only aesthetic but also economic value of a certain region, they should be valorized in order to provide good basis for creating valuable tourism product. Rivers as such, are the best representatives that provide possibilities for developing different types of tourism, which could give huge benefits for the region. In this paper, the focus is on the river Danube which is the second largest river in Europe and part of Corridor VII. The aim of this paper is to evaluate and bring this river closer to the population of Serbia. Also, the intention is to show the importance of the Danube, since it flows through Novi Sad and has a great potential for developing nautical and cruising tourism. Investments in this resource would significantly contribute to the development of an integrated tourist product of Novi Sad and Serbia. Bearing all this in mind, this paper will present the results of evaluation of the Danube, based on model of Hilary Du Cros.

  16. Vehicle rollover sensor test modeling

    NARCIS (Netherlands)

    McCoy, R.W.; Chou, C.C.; Velde, R. van de; Twisk, D.; Schie, C. van

    2007-01-01

    A computational model of a mid-size sport utility vehicle was developed using MADYMO. The model includes a detailed description of the suspension system and tire characteristics that incorporated the Delft-Tyre magic formula description. The model was correlated by simulating a vehicle suspension

  17. Engineering model cryocooler test results

    International Nuclear Information System (INIS)

    Skimko, M.A.; Stacy, W.D.; McCormick, J.A.

    1992-01-01

    This paper reports that recent testing of diaphragm-defined, Stirling-cycle machines and components has demonstrated cooling performance potential, validated the design code, and confirmed several critical operating characteristics. A breadboard cryocooler was rebuilt and tested from cryogenic to near-ambient cold end temperatures. There was a significant increase in capacity at cryogenic temperatures and the performance results compared will with code predictions at all temperatures. Further testing on a breadboard diaphragm compressor validated the calculated requirement for a minimum axial clearance between diaphragms and mating heads

  18. Testing homogeneity in Weibull-regression models.

    Science.gov (United States)

    Bolfarine, Heleno; Valença, Dione M

    2005-10-01

    In survival studies with families or geographical units it may be of interest testing whether such groups are homogeneous for given explanatory variables. In this paper we consider score type tests for group homogeneity based on a mixing model in which the group effect is modelled as a random variable. As opposed to hazard-based frailty models, this model presents survival times that conditioned on the random effect, has an accelerated failure time representation. The test statistics requires only estimation of the conventional regression model without the random effect and does not require specifying the distribution of the random effect. The tests are derived for a Weibull regression model and in the uncensored situation, a closed form is obtained for the test statistic. A simulation study is used for comparing the power of the tests. The proposed tests are applied to real data sets with censored data.

  19. The Model Identification Test: A Limited Verbal Science Test

    Science.gov (United States)

    McIntyre, P. J.

    1972-01-01

    Describes the production of a test with a low verbal load for use with elementary school science students. Animated films were used to present appropriate and inappropriate models of the behavior of particles of matter. (AL)

  20. Theoretical Models, Assessment Frameworks and Test Construction.

    Science.gov (United States)

    Chalhoub-Deville, Micheline

    1997-01-01

    Reviews the usefulness of proficiency models influencing second language testing. Findings indicate that several factors contribute to the lack of congruence between models and test construction and make a case for distinguishing between theoretical models. Underscores the significance of an empirical, contextualized and structured approach to the…

  1. Geochemical Testing And Model Development - Residual Tank Waste Test Plan

    International Nuclear Information System (INIS)

    Cantrell, K.J.; Connelly, M.P.

    2010-01-01

    This Test Plan describes the testing and chemical analyses release rate studies on tank residual samples collected following the retrieval of waste from the tank. This work will provide the data required to develop a contaminant release model for the tank residuals from both sludge and salt cake single-shell tanks. The data are intended for use in the long-term performance assessment and conceptual model development.

  2. Hydraulic Model Tests on Modified Wave Dragon

    DEFF Research Database (Denmark)

    Hald, Tue; Lynggaard, Jakob

    A floating model of the Wave Dragon (WD) was built in autumn 1998 by the Danish Maritime Institute in scale 1:50, see Sørensen and Friis-Madsen (1999) for reference. This model was subjected to a series of model tests and subsequent modifications at Aalborg University and in the following...... are found in Hald and Lynggaard (2001). Model tests and reconstruction are carried out during the phase 3 project: ”Wave Dragon. Reconstruction of an existing model in scale 1:50 and sequentiel tests of changes to the model geometry and mass distribution parameters” sponsored by the Danish Energy Agency...

  3. A model for optimal constrained adaptive testing

    NARCIS (Netherlands)

    van der Linden, Willem J.; Reese, Lynda M.

    2001-01-01

    A model for constrained computerized adaptive testing is proposed in which the information on the test at the ability estimate is maximized subject to a large variety of possible constraints on the contents of the test. At each item-selection step, a full test is first assembled to have maximum

  4. A model for optimal constrained adaptive testing

    NARCIS (Netherlands)

    van der Linden, Willem J.; Reese, Lynda M.

    1997-01-01

    A model for constrained computerized adaptive testing is proposed in which the information in the test at the ability estimate is maximized subject to a large variety of possible constraints on the contents of the test. At each item-selection step, a full test is first assembled to have maximum

  5. Traceability in Model-Based Testing

    Directory of Open Access Journals (Sweden)

    Mathew George

    2012-11-01

    Full Text Available The growing complexities of software and the demand for shorter time to market are two important challenges that face today’s IT industry. These challenges demand the increase of both productivity and quality of software. Model-based testing is a promising technique for meeting these challenges. Traceability modeling is a key issue and challenge in model-based testing. Relationships between the different models will help to navigate from one model to another, and trace back to the respective requirements and the design model when the test fails. In this paper, we present an approach for bridging the gaps between the different models in model-based testing. We propose relation definition markup language (RDML for defining the relationships between models.

  6. Test facility TIMO for testing the ITER model cryopump

    International Nuclear Information System (INIS)

    Haas, H.; Day, C.; Mack, A.; Methe, S.; Boissin, J.C.; Schummer, P.; Murdoch, D.K.

    2001-01-01

    Within the framework of the European Fusion Technology Programme, FZK is involved in the research and development process for a vacuum pump system of a future fusion reactor. As a result of these activities, the concept and the necessary requirements for the primary vacuum system of the ITER fusion reactor were defined. Continuing that development process, FZK has been preparing the test facility TIMO (Test facility for ITER Model pump) since 1996. This test facility provides for testing a cryopump all needed infrastructure as for example a process gas supply including a metering system, a test vessel, the cryogenic supply for the different temperature levels and a gas analysing system. For manufacturing the ITER model pump an order was given to the company L' Air Liquide in the form of a NET contract. (author)

  7. Test facility TIMO for testing the ITER model cryopump

    International Nuclear Information System (INIS)

    Haas, H.; Day, C.; Mack, A.; Methe, S.; Boissin, J.C.; Schummer, P.; Murdoch, D.K.

    1999-01-01

    Within the framework of the European Fusion Technology Programme, FZK is involved in the research and development process for a vacuum pump system of a future fusion reactor. As a result of these activities, the concept and the necessary requirements for the primary vacuum system of the ITER fusion reactor were defined. Continuing that development process, FZK has been preparing the test facility TIMO (Test facility for ITER Model pump) since 1996. This test facility provides for testing a cryopump all needed infrastructure as for example a process gas supply including a metering system, a test vessel, the cryogenic supply for the different temperature levels and a gas analysing system. For manufacturing the ITER model pump an order was given to the company L'Air Liquide in the form of a NET contract. (author)

  8. Statistical Tests for Mixed Linear Models

    CERN Document Server

    Khuri, André I; Sinha, Bimal K

    2011-01-01

    An advanced discussion of linear models with mixed or random effects. In recent years a breakthrough has occurred in our ability to draw inferences from exact and optimum tests of variance component models, generating much research activity that relies on linear models with mixed and random effects. This volume covers the most important research of the past decade as well as the latest developments in hypothesis testing. It compiles all currently available results in the area of exact and optimum tests for variance component models and offers the only comprehensive treatment for these models a

  9. Results of steel containment vessel model test

    International Nuclear Information System (INIS)

    Luk, V.K.; Ludwigsen, J.S.; Hessheimer, M.F.; Komine, Kuniaki; Matsumoto, Tomoyuki; Costello, J.F.

    1998-05-01

    A series of static overpressurization tests of scale models of nuclear containment structures is being conducted by Sandia National Laboratories for the Nuclear Power Engineering Corporation of Japan and the US Nuclear Regulatory Commission. Two tests are being conducted: (1) a test of a model of a steel containment vessel (SCV) and (2) a test of a model of a prestressed concrete containment vessel (PCCV). This paper summarizes the conduct of the high pressure pneumatic test of the SCV model and the results of that test. Results of this test are summarized and are compared with pretest predictions performed by the sponsoring organizations and others who participated in a blind pretest prediction effort. Questions raised by this comparison are identified and plans for posttest analysis are discussed

  10. lmerTest Package: Tests in Linear Mixed Effects Models

    DEFF Research Database (Denmark)

    Kuznetsova, Alexandra; Brockhoff, Per B.; Christensen, Rune Haubo Bojesen

    2017-01-01

    One of the frequent questions by users of the mixed model function lmer of the lme4 package has been: How can I get p values for the F and t tests for objects returned by lmer? The lmerTest package extends the 'lmerMod' class of the lme4 package, by overloading the anova and summary functions...... by providing p values for tests for fixed effects. We have implemented the Satterthwaite's method for approximating degrees of freedom for the t and F tests. We have also implemented the construction of Type I - III ANOVA tables. Furthermore, one may also obtain the summary as well as the anova table using...

  11. A screening model for depleted uranium testing using environmental radiation monitoring data

    International Nuclear Information System (INIS)

    Dunfrund, F.L.; Ebinger, M.H.; Hansen, W.R.

    1996-01-01

    Information from an ecological risk assessment of depleted uranium test areas at Yuma Proving Ground (YPG) was used to update the required environmental radiation monitoring (ERM) plan. Data to be collected for the ERM can also be used to evaluate the potential for adverse radiological and toxicological effects to terrestrial reptiles and mammals in the affected areas. We developed a spreadsheet-based screening model that incorporates the ERM data and associated uncertainties. The purpose of the model is to provide a conservative estimate of radiological exposure of terrestrial, biota to DU using the ERM data. The uncertainty in the estimate is also predicted so that the variation in the radiological exposure can be used in assessing potential adverse effects from DU testing. Toxicological effects are evaluated as well as radiological effects in the same program using the same data. Our presentation shows an example data set, model calculations, and the report of expected radiation dose rates and probable kidney burdens of select mammals and reptiles. The model can also be used in an inverse mode to calculate the soil concentration required to give either a radiological dose that would produce a potential adverse effect such as fatal cancer or a toxicological dose that would result in nephrotoxic effects in mammals

  12. Field testing of bioenergetic models

    International Nuclear Information System (INIS)

    Nagy, K.A.

    1985-01-01

    Doubly labeled water provides a direct measure of the rate of carbon dioxide production by free-living animals. With appropriate conversion factors, based on chemical composition of the diet and assimilation efficiency, field metabolic rate (FMR), in units of energy expenditure, and field feeding rate can be estimated. Validation studies indicate that doubly labeled water measurements of energy metabolism are accurate to within 7% in reptiles, birds, and mammals. This paper discusses the use of doubly labeled water to generate empirical models for FMR and food requirements for a variety of animals

  13. Linear Logistic Test Modeling with R

    Science.gov (United States)

    Baghaei, Purya; Kubinger, Klaus D.

    2015-01-01

    The present paper gives a general introduction to the linear logistic test model (Fischer, 1973), an extension of the Rasch model with linear constraints on item parameters, along with eRm (an R package to estimate different types of Rasch models; Mair, Hatzinger, & Mair, 2014) functions to estimate the model and interpret its parameters. The…

  14. TESTING GARCH-X TYPE MODELS

    DEFF Research Database (Denmark)

    Pedersen, Rasmus Søndergaard; Rahbek, Anders

    2017-01-01

    We present novel theory for testing for reduction of GARCH-X type models with an exogenous (X) covariate to standard GARCH type models. To deal with the problems of potential nuisance parameters on the boundary of the parameter space as well as lack of identification under the null, we exploit...... a noticeable property of specific zero-entries in the inverse information of the GARCH-X type models. Specifically, we consider sequential testing based on two likelihood ratio tests and as demonstrated the structure of the inverse information implies that the proposed test neither depends on whether...... the nuisance parameters lie on the boundary of the parameter space, nor on lack of identification. Our general results on GARCH-X type models are applied to Gaussian based GARCH-X models, GARCH-X models with Student's t-distributed innovations as well as the integer-valued GARCH-X (PAR-X) models....

  15. Summary Report of Depleted Uranium (DU) Survey Actions at Nevada Test and Training Range (NTTR), Airspace Region 63B, Active Target Complex 10 (63-10)

    Science.gov (United States)

    2016-09-15

    Sep 2016. a. In October 1992, the former Armstrong Laboratory Health Physics Function, now USAFSAM/OEC, took air and radiation samples during...in primary drainage areas, evidenced by the lack of DU activity above background in soil samples . However, survey measurements revealed elevated DU...and soil sampling in the primary drainage regions south of the active targets. It was also recommended that access to another area (NTTR 63-08

  16. Constraining performance assessment models with tracer test results: a comparison between two conceptual models

    Science.gov (United States)

    McKenna, Sean A.; Selroos, Jan-Olof

    Tracer tests are conducted to ascertain solute transport parameters of a single rock feature over a 5-m transport pathway. Two different conceptualizations of double-porosity solute transport provide estimates of the tracer breakthrough curves. One of the conceptualizations (single-rate) employs a single effective diffusion coefficient in a matrix with infinite penetration depth. However, the tracer retention between different flow paths can vary as the ratio of flow-wetted surface to flow rate differs between the path lines. The other conceptualization (multirate) employs a continuous distribution of multiple diffusion rate coefficients in a matrix with variable, yet finite, capacity. Application of these two models with the parameters estimated on the tracer test breakthrough curves produces transport results that differ by orders of magnitude in peak concentration and time to peak concentration at the performance assessment (PA) time and length scales (100,000 years and 1,000 m). These differences are examined by calculating the time limits for the diffusive capacity to act as an infinite medium. These limits are compared across both conceptual models and also against characteristic times for diffusion at both the tracer test and PA scales. Additionally, the differences between the models are examined by re-estimating parameters for the multirate model from the traditional double-porosity model results at the PA scale. Results indicate that for each model the amount of the diffusive capacity that acts as an infinite medium over the specified time scale explains the differences between the model results and that tracer tests alone cannot provide reliable estimates of transport parameters for the PA scale. Results of Monte Carlo runs of the transport models with varying travel times and path lengths show consistent results between models and suggest that the variation in flow-wetted surface to flow rate along path lines is insignificant relative to variability in

  17. 3D modeling of stratigraphic units and simulation of seismic facies in the Lion gulf margin; Modelisation 3D des unites stratigraphiques et simulation des facies sismiques dans la marge du golfe du Lion

    Energy Technology Data Exchange (ETDEWEB)

    Chihi, H.

    1997-05-12

    This work aims at providing a contribution to the studies carried out on reservoir characterization by use of seismic data. The study mainly consisted in the use of geostatistical methods in order to model the geometry of stratigraphic units of the Golfe du Lion margin and to simulate the seismic facies from high resolution seismic data. We propose, for the geometric modelling, a methodology based on the estimation of the surfaces and calculation afterwards of the thicknesses, if the modelling of the depth is possible. On the other hand the method consists in estimating the thickness variable directly and in deducing the boundary surfaces afterwards. In order to simulate the distribution of seismic facies within the units of the western domain, we used the truncated Gaussian method. The used approach gave a satisfactory results, when the seismic facies present slightly dipping reflectors with respect to the reference level. Otherwise the method reaches its limits because of the problems of definition of a reference level which allows to follow the clino-forms. In spite of these difficulties, this simulation allows us to estimate the distribution of seismic facies within the units and then to deduce their probable extension. (author) 150 refs.

  18. The Couplex test cases: models and lessons

    International Nuclear Information System (INIS)

    Bourgeat, A.; Kern, M.; Schumacher, S.; Talandier, J.

    2003-01-01

    The Couplex test cases are a set of numerical test models for nuclear waste deep geological disposal simulation. They are centered around the numerical issues arising in the near and far field transport simulation. They were used in an international contest, and are now becoming a reference in the field. We present the models used in these test cases, and show sample results from the award winning teams. (authors)

  19. Pharmacokinetic-Pharmacodynamic Analysis on Inflammation Rat Model after Oral Administration of Huang Lian Jie Du Decoction.

    Directory of Open Access Journals (Sweden)

    Wei Ren

    Full Text Available Huang-Lian-Jie-Du Decoction (HLJDD is a classical Traditional Chinese Medicine (TCM formula with heat-dissipating and detoxifying effects. It is used to treat inflammation-associated diseases. However, no systematic pharmacokinetic (PK and pharmacodynamic (PD data concerning the activity of HLJDD under inflammatory conditions is available to date. In the present study, the concentration-time profiles and the hepatic clearance rates (HCR of 41 major components in rat plasma in response to the oral administration of a clinical dose of HLJDD were investigated by LC-QqQ-MS using a dynamic multiple reaction monitoring (DMRM method. Additionally, the levels of 7 cytokines (CKs in the plasma and the body temperature of rats were analyzed. Furthermore, a PK-PD model was established to describe the time course of the hemodynamic and anti-inflammatory effects of HLJDD. As one of the three major active constituents in HLJDD, iridoids were absorbed and eliminated more easily and quickly than alkaloids and flavonoids. Compared with the normal controls, the flavonoids, alkaloids and iridoids in inflamed rats exhibited consistently changing trends of PK behaviors, such as higher bioavailability, slower elimination, delays in reaching the maximum concentration (Tmax and longer substantivity. The HCR of iridoids was different from that of alkaloids and flavonoids in inflamed rats. Furthermore, excellent pharmacodynamic effects of HLJDD were observed in inflamed rats. The levels of tumor necrosis factor-α (TNF-α, interleukin-6 (IL-6, IL-1β, IL-10, and macrophage inflammatory protein-2 (MIP-2 and body temperature significantly decreased after the administration of HLJDD. Based on PK-PD modeling with the three-phase synchronous characterization of time-concentration-effect, flavonoids exhibited one mechanism of action in the anti-inflammatory process, while iridoids and alkaloids showed another mechanism of action. Taken together, the results demonstrated that

  20. Tree-Based Global Model Tests for Polytomous Rasch Models

    Science.gov (United States)

    Komboz, Basil; Strobl, Carolin; Zeileis, Achim

    2018-01-01

    Psychometric measurement models are only valid if measurement invariance holds between test takers of different groups. Global model tests, such as the well-established likelihood ratio (LR) test, are sensitive to violations of measurement invariance, such as differential item functioning and differential step functioning. However, these…

  1. In-situ test of the static behaviour of a pile foundation subjected to thermo-mechanical solicitations. Intermediate report of January 1999; Test en conditions reelles du comportement statique d`un pieu soumis a des sollicitations thermo-mecaniques. Rapport intermediaire de janvier 1999

    Energy Technology Data Exchange (ETDEWEB)

    Moreni, M.; Laloui, L.; Steinmann, G. [and others

    1999-10-01

    A pile foundation of the polyvalent building in the north quarter of the Federal Institute of Technology in Lausanne (EPFL) was equipped with a hydraulic circuit in order to be able to inject heat into the pile (i.e. the pile was transformed into a heat exchanger pile). Load, deformation and temperature sensors were installed in the pile in order to assess the influence of thermal solicitations on the static behaviour of the pile. In the initial phase of the project (up to May 1998), the design and realisation of the heat exchanger pile was scheduled together with the installation of the measurement sensors. The next phase, ending one month after publication of the present report, is comprised of series of thermal solicitations applied in the pile, called tests. Due to the construction of the building, the weight on the pile increases between each test. This report contains the presentation of all the measurements done in the 6 tests performed in between the completion of each floor of the building. The pile was heated with a temperature difference of 15 K for each test, except for the first one, where it reached 22 K (this was before the construction of the building`s basement). The temperatures and deformations induced by the thermal and mechanical solicitations were measured and the stresses calculated at different depths of the pile (fluid temperatures, flow rate, electric and thermal powers) were continuously recorded. Sonic coring and a control using the reflection method were performed to determine the pile elastic modulus and the quality of its concrete. The last phase of the project (March - December 1999) deals with the analysis of the measurements in order to assess the influence of a temperature variation on the ability of the pile to support the load of the building [Francais] Un pieu du batiment polyvalent du Quartier Nord de l`Ecole Polytechnique Federale de Lausanne (EPFL) a ete equipe d`un circuit hydraulique pour pouvoir lui injecter de la chaleur

  2. Model tests for prestressed concrete pressure vessels

    International Nuclear Information System (INIS)

    Stoever, R.

    1975-01-01

    Investigations with models of reactor pressure vessels are used to check results of three dimensional calculation methods and to predict the behaviour of the prototype. Model tests with 1:50 elastic pressure vessel models and with a 1:5 prestressed concrete pressure vessel are described and experimental results are presented. (orig.) [de

  3. A Designer’s Guide to Human Performance Modelling (La Modelisation des Performances Humaines: Manuel du Concepteur).

    Science.gov (United States)

    1998-12-01

    into the Systems Engineering Process 17 5.3 Validation of HPMs 18 5.4 Commercialisation of human performance modelling software 18 5.5 Model Tool...budget) so that inappropriate models/tools are not offered. The WG agreed that another form of ’ educating ’ designers in the use of models was by means... Commercialisation of human performance modelling Software 5.2.8 Include human performance in system test. g More and more, customer’s are mandating the provision

  4. Model-based testing for embedded systems

    CERN Document Server

    Zander, Justyna; Mosterman, Pieter J

    2011-01-01

    What the experts have to say about Model-Based Testing for Embedded Systems: "This book is exactly what is needed at the exact right time in this fast-growing area. From its beginnings over 10 years ago of deriving tests from UML statecharts, model-based testing has matured into a topic with both breadth and depth. Testing embedded systems is a natural application of MBT, and this book hits the nail exactly on the head. Numerous topics are presented clearly, thoroughly, and concisely in this cutting-edge book. The authors are world-class leading experts in this area and teach us well-used

  5. Study of the long-term values and prices of plutonium; a simplified parametrized model; Etude des valeurs et des prix du plutonium a long terme; un modele parametre simplifie

    Energy Technology Data Exchange (ETDEWEB)

    Gaussens, J; Paillot, H [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1965-07-01

    The authors define the notions of use values and price of plutonium. They give a 'simplified parametrized model' simulating the equilibrium of the offer and the demand in time, concerning the plutonium and the price deriving from the relative scarcity of this metal, taking into account the technical and economic operating parameters of the various reactors confronted. This model is simple enough to allow direct computations and establish clear relations between the various parameters. The use of the linear programmes method allows on the other hand a wide extension of the model. This report includes three main parts: I - General description of the study (without detailed calculations) II - Mathematical development of the simplified parametrized model and application (the basic data and the results of the calculations are given) III - Appendices (giving the detailed computations of part II). (authors) [French] Les auteurs definissent les notions de valeurs d'usage et de prix du plutonium. Ils donnent un 'modele parametre simplifie' simulant l'equilibre de l'office et de la demande dans le temps concernant le plutonium et le prix qui decoule de la rarete relative de ce metal, compte tenu des parametres techniques et economiques de fonctionnement des divers reacteurs en presence. Ce modele est suffisamment simple pour permettre des calculs manuels et etablir des liaisons claires entre les divers parametres. L'utilisation de la technique des programmes lineaires permet par ailleurs une extension considerable du modele. Cette note comprend trois parties: I - Expose general de l'etude (sans expose du detail des calculs) II - Developpement mathematique du modele parametre simplifie et application (on precise les donnees de base et le resultat des calculs) III - Annexes (donnant le detail des calculs de la partie II). (auteurs)

  6. Test-driven modeling of embedded systems

    DEFF Research Database (Denmark)

    Munck, Allan; Madsen, Jan

    2015-01-01

    To benefit maximally from model-based systems engineering (MBSE) trustworthy high quality models are required. From the software disciplines it is known that test-driven development (TDD) can significantly increase the quality of the products. Using a test-driven approach with MBSE may have...... a similar positive effect on the quality of the system models and the resulting products and may therefore be desirable. To define a test-driven model-based systems engineering (TD-MBSE) approach, we must define this approach for numerous sub disciplines such as modeling of requirements, use cases...... suggest that our method provides a sound foundation for rapid development of high quality system models....

  7. 1/3-scale model testing program

    International Nuclear Information System (INIS)

    Yoshimura, H.R.; Attaway, S.W.; Bronowski, D.R.; Uncapher, W.L.; Huerta, M.; Abbott, D.G.

    1989-01-01

    This paper describes the drop testing of a one-third scale model transport cask system. Two casks were supplied by Transnuclear, Inc. (TN) to demonstrate dual purpose shipping/storage casks. These casks will be used to ship spent fuel from DOEs West Valley demonstration project in New York to the Idaho National Engineering Laboratory (INEL) for long term spent fuel dry storage demonstration. As part of the certification process, one-third scale model tests were performed to obtain experimental data. Two 9-m (30-ft) drop tests were conducted on a mass model of the cask body and scaled balsa and redwood filled impact limiters. In the first test, the cask system was tested in an end-on configuration. In the second test, the system was tested in a slap-down configuration where the axis of the cask was oriented at a 10 degree angle with the horizontal. Slap-down occurs for shallow angle drops where the primary impact at one end of the cask is followed by a secondary impact at the other end. The objectives of the testing program were to (1) obtain deceleration and displacement information for the cask and impact limiter system, (2) obtain dynamic force-displacement data for the impact limiters, (3) verify the integrity of the impact limiter retention system, and (4) examine the crush behavior of the limiters. This paper describes both test results in terms of measured deceleration, post test deformation measurements, and the general structural response of the system

  8. Superconducting solenoid model magnet test results

    Energy Technology Data Exchange (ETDEWEB)

    Carcagno, R.; Dimarco, J.; Feher, S.; Ginsburg, C.M.; Hess, C.; Kashikhin, V.V.; Orris, D.F.; Pischalnikov, Y.; Sylvester, C.; Tartaglia, M.A.; Terechkine, I.; /Fermilab

    2006-08-01

    Superconducting solenoid magnets suitable for the room temperature front end of the Fermilab High Intensity Neutrino Source (formerly known as Proton Driver), an 8 GeV superconducting H- linac, have been designed and fabricated at Fermilab, and tested in the Fermilab Magnet Test Facility. We report here results of studies on the first model magnets in this program, including the mechanical properties during fabrication and testing in liquid helium at 4.2 K, quench performance, and magnetic field measurements. We also describe new test facility systems and instrumentation that have been developed to accomplish these tests.

  9. Superconducting solenoid model magnet test results

    International Nuclear Information System (INIS)

    Carcagno, R.; Dimarco, J.; Feher, S.; Ginsburg, C.M.; Hess, C.; Kashikhin, V.V.; Orris, D.F.; Pischalnikov, Y.; Sylvester, C.; Tartaglia, M.A.; Terechkine, I.; Tompkins, J.C.; Wokas, T.; Fermilab

    2006-01-01

    Superconducting solenoid magnets suitable for the room temperature front end of the Fermilab High Intensity Neutrino Source (formerly known as Proton Driver), an 8 GeV superconducting H- linac, have been designed and fabricated at Fermilab, and tested in the Fermilab Magnet Test Facility. We report here results of studies on the first model magnets in this program, including the mechanical properties during fabrication and testing in liquid helium at 4.2 K, quench performance, and magnetic field measurements. We also describe new test facility systems and instrumentation that have been developed to accomplish these tests

  10. Fiche technique du spermogramme et du spermocytogramme ...

    African Journals Online (AJOL)

    En Afrique la stérilité du couple constitue un drame social. Selon l'OMS, environ 8 à 12 % des couples africains sont touchés par une infertilité. La responsabilité masculine dans la stérilité est comprise entre 30 à 40%. Les causes de l'infertilité masculine peuvent être l'impuissance et/ ou l'altération du sperme. L'étude de ...

  11. Space Launch System Scale Model Acoustic Test Ignition Overpressure Testing

    Science.gov (United States)

    Nance, Donald; Liever, Peter; Nielsen, Tanner

    2015-01-01

    The overpressure phenomenon is a transient fluid dynamic event occurring during rocket propulsion system ignition. This phenomenon results from fluid compression of the accelerating plume gas, subsequent rarefaction, and subsequent propagation from the exhaust trench and duct holes. The high-amplitude unsteady fluid-dynamic perturbations can adversely affect the vehicle and surrounding structure. Commonly known as ignition overpressure (IOP), this is an important design-to environment for the Space Launch System (SLS) that NASA is currently developing. Subscale testing is useful in validating and verifying the IOP environment. This was one of the objectives of the Scale Model Acoustic Test, conducted at Marshall Space Flight Center. The test data quantifies the effectiveness of the SLS IOP suppression system and improves the analytical models used to predict the SLS IOP environments. The reduction and analysis of the data gathered during the SMAT IOP test series requires identification and characterization of multiple dynamic events and scaling of the event waveforms to provide the most accurate comparisons to determine the effectiveness of the IOP suppression systems. The identification and characterization of the overpressure events, the waveform scaling, the computation of the IOP suppression system knockdown factors, and preliminary comparisons to the analytical models are discussed.

  12. Space Launch System Scale Model Acoustic Test Ignition Overpressure Testing

    Science.gov (United States)

    Nance, Donald K.; Liever, Peter A.

    2015-01-01

    The overpressure phenomenon is a transient fluid dynamic event occurring during rocket propulsion system ignition. This phenomenon results from fluid compression of the accelerating plume gas, subsequent rarefaction, and subsequent propagation from the exhaust trench and duct holes. The high-amplitude unsteady fluid-dynamic perturbations can adversely affect the vehicle and surrounding structure. Commonly known as ignition overpressure (IOP), this is an important design-to environment for the Space Launch System (SLS) that NASA is currently developing. Subscale testing is useful in validating and verifying the IOP environment. This was one of the objectives of the Scale Model Acoustic Test (SMAT), conducted at Marshall Space Flight Center (MSFC). The test data quantifies the effectiveness of the SLS IOP suppression system and improves the analytical models used to predict the SLS IOP environments. The reduction and analysis of the data gathered during the SMAT IOP test series requires identification and characterization of multiple dynamic events and scaling of the event waveforms to provide the most accurate comparisons to determine the effectiveness of the IOP suppression systems. The identification and characterization of the overpressure events, the waveform scaling, the computation of the IOP suppression system knockdown factors, and preliminary comparisons to the analytical models are discussed.

  13. Do Test Design and Uses Influence Test Preparation? Testing a Model of Washback with Structural Equation Modeling

    Science.gov (United States)

    Xie, Qin; Andrews, Stephen

    2013-01-01

    This study introduces Expectancy-value motivation theory to explain the paths of influences from perceptions of test design and uses to test preparation as a special case of washback on learning. Based on this theory, two conceptual models were proposed and tested via Structural Equation Modeling. Data collection involved over 870 test takers of…

  14. Sample Size Determination for Rasch Model Tests

    Science.gov (United States)

    Draxler, Clemens

    2010-01-01

    This paper is concerned with supplementing statistical tests for the Rasch model so that additionally to the probability of the error of the first kind (Type I probability) the probability of the error of the second kind (Type II probability) can be controlled at a predetermined level by basing the test on the appropriate number of observations.…

  15. Is the standard model really tested?

    International Nuclear Information System (INIS)

    Takasugi, E.

    1989-01-01

    It is discussed how the standard model is really tested. Among various tests, I concentrate on the CP violation phenomena in K and B meson system. Especially, the resent hope to overcome the theoretical uncertainty in the evaluation on the CP violation of K meson system is discussed. (author)

  16. Les Cahiers du CREAD

    African Journals Online (AJOL)

    Admin

    politique de bas prix exercée par la Russie et le Qatar vient confirmer ce constat ; s'ajoute à cela l'entrée éventuelle du gaz non conven- tionnel, dont son prix actuel de 3/4 $US, offre aux USA l'opportunité d'être exportateur de ..... les compagnies à produire en matière du gaz naturel, tels le prix du gaz naturel, le prix des ...

  17. Bulletin du CRDI #124

    International Development Research Centre (IDRC) Digital Library (Canada)

    Les femmes jouent un rôle important dans les exploitations minières artisanales et à petite échelle en Afrique subsaharienne. De concert ... Couverture du livre: Une vie saine pour les femmes et les enfants vulnérables · Couverture du livre: Entre el activismo y la intervención · Couverture du livre: Revitalizing Health for All.

  18. Bulletin du CRDI #125

    International Development Research Centre (IDRC) Digital Library (Canada)

    L'IOSRS remporte le prix de la diplomatie scientifique · GrowInclusive : la plateforme tant attendue est en construction · Toutes les nouvelles. Activités à venir. Semaine du développement international 2018. Le CRDI célébrera la Semaine du développement international du 4 au 10 février 2018. Suivez-nous sur Twitter et ...

  19. Modelling and Testing of Friction in Forging

    DEFF Research Database (Denmark)

    Bay, Niels

    2007-01-01

    Knowledge about friction is still limited in forging. The theoretical models applied presently for process analysis are not satisfactory compared to the advanced and detailed studies possible to carry out by plastic FEM analyses and more refined models have to be based on experimental testing...

  20. A Comprehensive Model of the Dry Desulphurisation Process Une modélisation non empirique du procédé de désulfuration par voie sèche

    Directory of Open Access Journals (Sweden)

    Flament P.

    2006-11-01

    Full Text Available Due to the high investment cost of the wet scrubbing, the dry desulphurisation process remains an attractive way to remove sulphur dioxide when reduction level should not be higher than 90%. In this technique, the SO2 is removed from flue gases by direct injection of small calcium based sorbents such as calcium carbonate (CaCO3 or calcium hydroxide (Ca(OH² . The sorbent is first transformed into calcium oxide (CaO before reacting with SO2 to form a stable calcium sulphate (CaSO4. Although the global reactions are rather simple, a full description of the mechanism requires the knowledge of both, the initial physical properties of the sorbent and the evolution of these properties during the reaction. Furthermore, the way how particles are injected and dispersed into the SO2 containing gases is also a major issue of the dry desulphurisation process. Both aspects are considered in this paper since a specialised routine was build to describe the calcination-sulphation process and coupled with the KIVA code to perform 3D calculations under real industrial conditions. The desulphurisation model was first tested alone using the kinetic data of the International Flame Research Foundation and then, coupled with KIVA to simulate the desulphurisation process in a new type of boiler which is developed by BABCOCK Entreprise and the Institut Français du Pétrole (the AUDE boiler. In this last case, the objective was to determine the sorbent injection locations leading to the highest desulphurisation efficiencies. As the dispersion of particles is an important parameter of the desulphurisation process, an example of validation of the KIVA dispersion model is also presented in this paper. For the selected test case, i. e: particle dispersion in a plane mixing layer, a good agreement was found between the experimental results of Ando et al (1990 and the calculations performed with KIVA. Par suite du coût d'investissement très élevé du procédé de lavage

  1. Kinematic tests of exotic flat cosmological models

    International Nuclear Information System (INIS)

    Charlton, J.C.; Turner, M.S.; NASA/Fermilab Astrophysics Center, Batavia, IL)

    1987-01-01

    Theoretical prejudice and inflationary models of the very early universe strongly favor the flat, Einstein-de Sitter model of the universe. At present the observational data conflict with this prejudice. This conflict can be resolved by considering flat models of the universe which posses a smooth component of energy density. The kinematics of such models, where the smooth component is relativistic particles, a cosmological term, a network of light strings, or fast-moving, light strings is studied in detail. The observational tests which can be used to discriminate between these models are also discussed. These tests include the magnitude-redshift, lookback time-redshift, angular size-redshift, and comoving volume-redshift diagrams and the growth of density fluctuations. 58 references

  2. Kinematic tests of exotic flat cosmological models

    International Nuclear Information System (INIS)

    Charlton, J.C.; Turner, M.S.

    1986-05-01

    Theoretical prejudice and inflationary models of the very early Universe strongly favor the flat, Einstein-deSitter model of the Universe. At present the observational data conflict with this prejudice. This conflict can be resolved by considering flat models of the Universe which possess a smooth component by energy density. We study in detail the kinematics of such models, where the smooth component is relativistic particles, a cosmological term, a network of light strings, or fast-moving, light strings. We also discuss the observational tests which can be used to discriminate between these models. These tests include the magnitude-redshift, lookback time-redshift, angular size-redshift, and comoving volume-redshift diagrams and the growth of density fluctuations

  3. Kinematic tests of exotic flat cosmological models

    Energy Technology Data Exchange (ETDEWEB)

    Charlton, J.C.; Turner, M.S.

    1986-05-01

    Theoretical prejudice and inflationary models of the very early Universe strongly favor the flat, Einstein-deSitter model of the Universe. At present the observational data conflict with this prejudice. This conflict can be resolved by considering flat models of the Universe which possess a smooth component by energy density. We study in detail the kinematics of such models, where the smooth component is relativistic particles, a cosmological term, a network of light strings, or fast-moving, light strings. We also discuss the observational tests which can be used to discriminate between these models. These tests include the magnitude-redshift, lookback time-redshift, angular size-redshift, and comoving volume-redshift diagrams and the growth of density fluctuations.

  4. Observation-Based Modeling for Model-Based Testing

    NARCIS (Netherlands)

    Kanstrén, T.; Piel, E.; Gross, H.G.

    2009-01-01

    One of the single most important reasons that modeling and modelbased testing are not yet common practice in industry is the perceived difficulty of making the models up to the level of detail and quality required for their automated processing. Models unleash their full potential only through

  5. A 'Turing' Test for Landscape Evolution Models

    Science.gov (United States)

    Parsons, A. J.; Wise, S. M.; Wainwright, J.; Swift, D. A.

    2008-12-01

    Resolving the interactions among tectonics, climate and surface processes at long timescales has benefited from the development of computer models of landscape evolution. However, testing these Landscape Evolution Models (LEMs) has been piecemeal and partial. We argue that a more systematic approach is required. What is needed is a test that will establish how 'realistic' an LEM is and thus the extent to which its predictions may be trusted. We propose a test based upon the Turing Test of artificial intelligence as a way forward. In 1950 Alan Turing posed the question of whether a machine could think. Rather than attempt to address the question directly he proposed a test in which an interrogator asked questions of a person and a machine, with no means of telling which was which. If the machine's answer could not be distinguished from those of the human, the machine could be said to demonstrate artificial intelligence. By analogy, if an LEM cannot be distinguished from a real landscape it can be deemed to be realistic. The Turing test of intelligence is a test of the way in which a computer behaves. The analogy in the case of an LEM is that it should show realistic behaviour in terms of form and process, both at a given moment in time (punctual) and in the way both form and process evolve over time (dynamic). For some of these behaviours, tests already exist. For example there are numerous morphometric tests of punctual form and measurements of punctual process. The test discussed in this paper provides new ways of assessing dynamic behaviour of an LEM over realistically long timescales. However challenges remain in developing an appropriate suite of challenging tests, in applying these tests to current LEMs and in developing LEMs that pass them.

  6. Engineering Abstractions in Model Checking and Testing

    DEFF Research Database (Denmark)

    Achenbach, Michael; Ostermann, Klaus

    2009-01-01

    Abstractions are used in model checking to tackle problems like state space explosion or modeling of IO. The application of these abstractions in real software development processes, however, lacks engineering support. This is one reason why model checking is not widely used in practice yet...... and testing is still state of the art in falsification. We show how user-defined abstractions can be integrated into a Java PathFinder setting with tools like AspectJ or Javassist and discuss implications of remaining weaknesses of these tools. We believe that a principled engineering approach to designing...... and implementing abstractions will improve the applicability of model checking in practice....

  7. Pile Model Tests Using Strain Gauge Technology

    Science.gov (United States)

    Krasiński, Adam; Kusio, Tomasz

    2015-09-01

    Ordinary pile bearing capacity tests are usually carried out to determine the relationship between load and displacement of pile head. The measurement system required in such tests consists of force transducer and three or four displacement gauges. The whole system is installed at the pile head above the ground level. This approach, however, does not give us complete information about the pile-soil interaction. We can only determine the total bearing capacity of the pile, without the knowledge of its distribution into the shaft and base resistances. Much more information can be obtained by carrying out a test of instrumented pile equipped with a system for measuring the distribution of axial force along its core. In the case of pile model tests the use of such measurement is difficult due to small scale of the model. To find a suitable solution for axial force measurement, which could be applied to small scale model piles, we had to take into account the following requirements: - a linear and stable relationship between measured and physical values, - the force measurement accuracy of about 0.1 kN, - the range of measured forces up to 30 kN, - resistance of measuring gauges against aggressive counteraction of concrete mortar and against moisture, - insensitivity to pile bending, - economical factor. These requirements can be fulfilled by strain gauge sensors if an appropriate methodology is used for test preparation (Hoffmann [1]). In this paper, we focus on some aspects of the application of strain gauge sensors for model pile tests. The efficiency of the method is proved on the examples of static load tests carried out on SDP model piles acting as single piles and in a group.

  8. Neutrino mass and physics beyond the Standard Model; Masse des Neutrinos et Physique au-dela du Modele Standard

    Energy Technology Data Exchange (ETDEWEB)

    Hosteins, P

    2007-09-15

    The purpose of this thesis is to study, in the neutrino sector, the flavour structures at high energy. The work is divided into two main parts. The first part is dedicated to the well known mechanism to produce small neutrino masses: the seesaw mechanism, which implies the existence of massive particles whose decays violate lepton number. Therefore this mechanism can also be used to generate a net baryon number in the early universe and explain the cosmological observation of the asymmetry between matter and antimatter. However, it is often non-trivial to fulfill the constraints coming at the same time from neutrino oscillations and cosmological experiments, at least in frameworks where the couplings can be somehow constrained, like some Grand Unification models. Therefore we devoted the first part to the study of a certain class of seesaw mechanism which can be found in the context of SO(10) theories for example. We introduce a method to extract the mass matrix of the heavy right-handed neutrinos and explore the phenomenological consequences of this quantity, mainly concerning the production of a sufficient baryon asymmetry. When trying to identify the underlying symmetry governing the mixings between the different generations, we see that there is a puzzling difference between the quark and the lepton sectors. However, the quark and lepton parameters have to be compared at the scale of the flavour symmetry breaking, therefore we have to make them run to the appropriate scale. Thus, it is worthwhile investigating models where quantum corrections allow an approximate unification of quark and lepton mixings. This is why the other part of the thesis investigates the running of the effective neutrino mass operator in models with an extra compact dimension, where quantum corrections to the neutrino masses and mixings can be potentially large due to the multiplicity of states.

  9. Accuracy tests of the tessellated SLBM model

    International Nuclear Information System (INIS)

    Ramirez, A L; Myers, S C

    2007-01-01

    We have compared the Seismic Location Base Model (SLBM) tessellated model (version 2.0 Beta, posted July 3, 2007) with the GNEMRE Unified Model. The comparison is done on a layer/depth-by-layer/depth and layer/velocity-by-layer/velocity comparison. The SLBM earth model is defined on a tessellation that spans the globe at a constant resolution of about 1 degree (Ballard, 2007). For the tests, we used the earth model in file ''unified( ) iasp.grid''. This model contains the top 8 layers of the Unified Model (UM) embedded in a global IASP91 grid. Our test queried the same set of nodes included in the UM model file. To query the model stored in memory, we used some of the functionality built into the SLBMInterface object. We used the method get InterpolatedPoint() to return desired values for each layer at user-specified points. The values returned include: depth to the top of each layer, layer velocity, layer thickness and (for the upper-mantle layer) velocity gradient. The SLBM earth model has an extra middle crust layer whose values are used when Pg/Lg phases are being calculated. This extra layer was not accessed by our tests. Figures 1 to 8 compare the layer depths, P velocities and P gradients in the UM and SLBM models. The figures show results for the three sediment layers, three crustal layers and the upper mantle layer defined in the UM model. Each layer in the models (sediment1, sediment2, sediment3, upper crust, middle crust, lower crust and upper mantle) is shown on a separate figure. The upper mantle P velocity and gradient distribution are shown on Figures 7 and 8. The left and center images in the top row of each figure is the rendering of depth to the top of the specified layer for the UM and SLBM models. When a layer has zero thickness, its depth is the same as that of the layer above. The right image in the top row is the difference between in layer depth for the UM and SLBM renderings. The left and center images in the bottom row of the figures are

  10. "Cirque du Freak."

    Science.gov (United States)

    Rivett, Miriam

    2002-01-01

    Considers the marketing strategies that underpin the success of the "Cirque du Freak" series. Describes how "Cirque du Freak" is an account of events in the life of schoolboy Darren Shan. Notes that it is another reworking of the vampire narrative, a sub-genre of horror writing that has proved highly popular with both adult and…

  11. Unit testing, model validation, and biological simulation.

    Science.gov (United States)

    Sarma, Gopal P; Jacobs, Travis W; Watts, Mark D; Ghayoomie, S Vahid; Larson, Stephen D; Gerkin, Richard C

    2016-01-01

    The growth of the software industry has gone hand in hand with the development of tools and cultural practices for ensuring the reliability of complex pieces of software. These tools and practices are now acknowledged to be essential to the management of modern software. As computational models and methods have become increasingly common in the biological sciences, it is important to examine how these practices can accelerate biological software development and improve research quality. In this article, we give a focused case study of our experience with the practices of unit testing and test-driven development in OpenWorm, an open-science project aimed at modeling Caenorhabditis elegans. We identify and discuss the challenges of incorporating test-driven development into a heterogeneous, data-driven project, as well as the role of model validation tests, a category of tests unique to software which expresses scientific models.

  12. Variable amplitude fatigue, modelling and testing

    International Nuclear Information System (INIS)

    Svensson, Thomas.

    1993-01-01

    Problems related to metal fatigue modelling and testing are here treated in four different papers. In the first paper different views of the subject are summarised in a literature survey. In the second paper a new model for fatigue life is investigated. Experimental results are established which are promising for further development of the mode. In the third paper a method is presented that generates a stochastic process, suitable to fatigue testing. The process is designed in order to resemble certain fatigue related features in service life processes. In the fourth paper fatigue problems in transport vibrations are treated

  13. Design, modeling and testing of data converters

    CERN Document Server

    Kiaei, Sayfe; Xu, Fang

    2014-01-01

    This book presents the a scientific discussion of the state-of-the-art techniques and designs for modeling, testing and for the performance analysis of data converters. The focus is put on sustainable data conversion. Sustainability has become a public issue that industries and users can not ignore. Devising environmentally friendly solutions for data conversion designing, modeling and testing is nowadays a requirement that researchers and practitioners must consider in their activities. This book presents the outcome of the IWADC workshop 2011, held in Orvieto, Italy.

  14. Modelling the hydro-mechanical behaviour of swelling unsaturated soils; Modelisation du comportement hydromecanique des sols gonflants non satures

    Energy Technology Data Exchange (ETDEWEB)

    Mrad, M

    2005-10-15

    The use of compacted swelling soils in engineering practice is very widely spread, especially in geotechnical and environmental engineering. After their setup, these materials are likely to be subject to complex suction/stress paths involving significant variations of their hydro-mechanical properties which can affect their initial behaviour. It is important to be able to predict the hydro-mechanical behaviour of these materials taking into account the significant applications for which they are intended. Barcelona team developed a finite-element code (Code-Bright) for the thermo-hydro-mechanical coupling (THM) integrating the BBM elastoplastic model for unsaturated soils based on the independent variables approach. This model is recognized to correctly describe the hydro-mechanical behaviour of unsaturated soils but fails to take into account some particular observed aspects on swelling soils. A second model BExM was then proposed to address these aspects. The objective of this study is: (i) to implement the elastoplastic model BExM for the unsaturated swelling soils in the finite-element code (Code-Bright); (ii) to check the numerical model validity through the numerical simulation of laboratory tests made on swelling soils; and (iii) to apply this model to some practical problems. For this purpose, a new family of numerical procedures adapted to the BExM model was introduced into the code. The equation of the yield surface of this model for a given deviatoric stress states was given in a manner to facilitate calculations of its derivatives. The model was checked by the numerical simulation of suction-controlled odometric tests made on three different swelling soils. The simulation results showed that the numerical model is able to correctly reproduce the experimental data. Lastly, the model was applied to two practical problems: radioactive waste repository in deep geological layers and a shallow footing under the action of a swelling soil. The results obtained

  15. Flight Test Maneuvers for Efficient Aerodynamic Modeling

    Science.gov (United States)

    Morelli, Eugene A.

    2011-01-01

    Novel flight test maneuvers for efficient aerodynamic modeling were developed and demonstrated in flight. Orthogonal optimized multi-sine inputs were applied to aircraft control surfaces to excite aircraft dynamic response in all six degrees of freedom simultaneously while keeping the aircraft close to chosen reference flight conditions. Each maneuver was designed for a specific modeling task that cannot be adequately or efficiently accomplished using conventional flight test maneuvers. All of the new maneuvers were first described and explained, then demonstrated on a subscale jet transport aircraft in flight. Real-time and post-flight modeling results obtained using equation-error parameter estimation in the frequency domain were used to show the effectiveness and efficiency of the new maneuvers, as well as the quality of the aerodynamic models that can be identified from the resultant flight data.

  16. Modeling and Testing Legacy Data Consistency Requirements

    DEFF Research Database (Denmark)

    Nytun, J. P.; Jensen, Christian Søndergaard

    2003-01-01

    An increasing number of data sources are available on the Internet, many of which offer semantically overlapping data, but based on different schemas, or models. While it is often of interest to integrate such data sources, the lack of consistency among them makes this integration difficult....... This paper addresses the need for new techniques that enable the modeling and consistency checking for legacy data sources. Specifically, the paper contributes to the development of a framework that enables consistency testing of data coming from different types of data sources. The vehicle is UML and its...... accompanying XMI. The paper presents techniques for modeling consistency requirements using OCL and other UML modeling elements: it studies how models that describe the required consistencies among instances of legacy models can be designed in standard UML tools that support XMI. The paper also considers...

  17. Testing of a steel containment vessel model

    International Nuclear Information System (INIS)

    Luk, V.K.; Hessheimer, M.F.; Matsumoto, T.; Komine, K.; Costello, J.F.

    1997-01-01

    A mixed-scale containment vessel model, with 1:10 in containment geometry and 1:4 in shell thickness, was fabricated to represent an improved, boiling water reactor (BWR) Mark II containment vessel. A contact structure, installed over the model and separated at a nominally uniform distance from it, provided a simplified representation of a reactor shield building in the actual plant. This paper describes the pretest preparations and the conduct of the high pressure test of the model performed on December 11-12, 1996. 4 refs., 2 figs

  18. Precision tests of the Standard Model

    International Nuclear Information System (INIS)

    Ol'shevskij, A.G.

    1996-01-01

    The present status of the precision measurements of electroweak observables is discussed with the special emphasis on the results obtained recently. All together these measurements provide the basis for the stringent test of the Standard Model and determination of the SM parameters. 22 refs., 23 figs., 11 tabs

  19. Binomial test models and item difficulty

    NARCIS (Netherlands)

    van der Linden, Willem J.

    1979-01-01

    In choosing a binomial test model, it is important to know exactly what conditions are imposed on item difficulty. In this paper these conditions are examined for both a deterministic and a stochastic conception of item responses. It appears that they are more restrictive than is generally

  20. Shallow foundation model tests in Europe

    Czech Academy of Sciences Publication Activity Database

    Feda, Jaroslav; Simonini, P.; Arslan, U.; Georgiodis, M.; Laue, J.; Pinto, I.

    1999-01-01

    Roč. 2, č. 4 (1999), s. 447-475 ISSN 1436-6517. [Int. Conf. on Soil - Structure Interaction in Urban Civ. Engineering. Darmstadt, 08.10.1999-09.10.1999] R&D Projects: GA MŠk OC C7.10 Keywords : shallow foundations * model tests * sandy subsoil * bearing capacity * settlement Subject RIV: JM - Building Engineering

  1. Testing mechanistic models of growth in insects.

    Science.gov (United States)

    Maino, James L; Kearney, Michael R

    2015-11-22

    Insects are typified by their small size, large numbers, impressive reproductive output and rapid growth. However, insect growth is not simply rapid; rather, insects follow a qualitatively distinct trajectory to many other animals. Here we present a mechanistic growth model for insects and show that increasing specific assimilation during the growth phase can explain the near-exponential growth trajectory of insects. The presented model is tested against growth data on 50 insects, and compared against other mechanistic growth models. Unlike the other mechanistic models, our growth model predicts energy reserves per biomass to increase with age, which implies a higher production efficiency and energy density of biomass in later instars. These predictions are tested against data compiled from the literature whereby it is confirmed that insects increase their production efficiency (by 24 percentage points) and energy density (by 4 J mg(-1)) between hatching and the attainment of full size. The model suggests that insects achieve greater production efficiencies and enhanced growth rates by increasing specific assimilation and increasing energy reserves per biomass, which are less costly to maintain than structural biomass. Our findings illustrate how the explanatory and predictive power of mechanistic growth models comes from their grounding in underlying biological processes. © 2015 The Author(s).

  2. Automatic apparatus and data transmission for field response tests of the ground; Automatisation et teletransmission des donnees pour les tests de reponse du terrain

    Energy Technology Data Exchange (ETDEWEB)

    Laloui, L.; Steinmann, G.

    2004-07-01

    This is the report on the third part of a development started 1998 at the Swiss Federal Institute of Technology Lausanne (EPFL) in Lausanne, Switzerland. Energy piles are becoming increasingly used as a heat exchanger and heat storage device, as are geothermal probes. Their design and sizing is subject to some uncertainty due to the fact that the planner has to estimate the thermal and mechanical properties of the ground surrounding the piles or probes. The aim of the project was to develop an apparatus for field measurements of thermal and mechanical properties of an energy pile or a geothermal probe (thermal response tests). In the reported third phase of the project the portable apparatus was equipped with a data transmission device using the Internet. Real-time data acquisition and supervision is now implemented and data processing has been improved. Another goal of the project was to obtain the official accreditation of such response tests according to the European standard EN 45,000. First operation experience from a test in Lyon, France is reported.

  3. Testing proton spin models with polarized beams

    International Nuclear Information System (INIS)

    Ramsey, G.P.

    1991-01-01

    We review models for spin-weighted parton distributions in a proton. Sum rules involving the nonsinglet components of the structure function xg 1 p help narrow the range of parameters in these models. The contribution of the γ 5 anomaly term depends on the size of the integrated polarized gluon distribution and experimental predictions depend on its size. We have proposed three models for the polarized gluon distributions, whose range is considerable. These model distributions give an overall range is considerable. These model distributions give an overall range of parameters that can be tested with polarized beam experiments. These are discussed with regard to specific predictions for polarized beam experiments at energies typical of UNK

  4. Testing Parametric versus Semiparametric Modelling in Generalized Linear Models

    NARCIS (Netherlands)

    Härdle, W.K.; Mammen, E.; Müller, M.D.

    1996-01-01

    We consider a generalized partially linear model E(Y|X,T) = G{X'b + m(T)} where G is a known function, b is an unknown parameter vector, and m is an unknown function.The paper introduces a test statistic which allows to decide between a parametric and a semiparametric model: (i) m is linear, i.e.

  5. OTEC riser cable model and prototype testing

    Science.gov (United States)

    Kurt, J. P.; Schultz, J. A.; Roblee, L. H. S.

    1981-12-01

    Two different OTEC riser cables have been developed to span the distance between a floating OTEC power plant and the ocean floor. The major design concerns for a riser cable in the dynamic OTEC environment are fatigue, corrosion, and electrical/mechanical aging of the cable components. The basic properties of the cable materials were studied through tests on model cables and on samples of cable materials. Full-scale prototype cables were manufactured and were tested to measure their electrical and mechanical properties and performance. The full-scale testing was culminated by the electrical/mechanical fatigue test, which exposes full-scale cables to simultaneous tension, bending and electrical loads, all in a natural seawater environment.

  6. Modelling the long-range transport. Atmospheric model from the Oslo EMEP-W center; Modelisation du transfert a longue distance modele atmospherique du centre Emep-W- a Oslo

    Energy Technology Data Exchange (ETDEWEB)

    Joffre, S. [Institut Meteorolique de Finlande Geographical Research Vuorikatu, Helsinki (Finland)

    1997-12-31

    In the framework of the European Monitoring and Evaluation Program (EMEP) concerning transfrontier air pollution in Europe, a model has been developed which gives, based on pollution emission and meteorological data, monthly and annual values for the atmospheric content of ten major pollutants, the deposited dry and wet compounds, and the source allocations. Physical principles of the model and its validation are described

  7. Prospective Tests on Biological Models of Acupuncture

    Directory of Open Access Journals (Sweden)

    Charles Shang

    2009-01-01

    Full Text Available The biological effects of acupuncture include the regulation of a variety of neurohumoral factors and growth control factors. In science, models or hypotheses with confirmed predictions are considered more convincing than models solely based on retrospective explanations. Literature review showed that two biological models of acupuncture have been prospectively tested with independently confirmed predictions: The neurophysiology model on the long-term effects of acupuncture emphasizes the trophic and anti-inflammatory effects of acupuncture. Its prediction on the peripheral effect of endorphin in acupuncture has been confirmed. The growth control model encompasses the neurophysiology model and suggests that a macroscopic growth control system originates from a network of organizers in embryogenesis. The activity of the growth control system is important in the formation, maintenance and regulation of all the physiological systems. Several phenomena of acupuncture such as the distribution of auricular acupuncture points, the long-term effects of acupuncture and the effect of multimodal non-specific stimulation at acupuncture points are consistent with the growth control model. The following predictions of the growth control model have been independently confirmed by research results in both acupuncture and conventional biomedical sciences: (i Acupuncture has extensive growth control effects. (ii Singular point and separatrix exist in morphogenesis. (iii Organizers have high electric conductance, high current density and high density of gap junctions. (iv A high density of gap junctions is distributed as separatrices or boundaries at body surface after early embryogenesis. (v Many acupuncture points are located at transition points or boundaries between different body domains or muscles, coinciding with the connective tissue planes. (vi Some morphogens and organizers continue to function after embryogenesis. Current acupuncture research suggests a

  8. Ecologie du phytoplancton du lac Kivu

    Directory of Open Access Journals (Sweden)

    Sarmento, H.

    2008-01-01

    Full Text Available Speciation within the African Coffee Pathogen. Cet article analyse s'il est avantageux d'utiliser le compost au lieu de l'engrais minéral pour produire la laitue dans la zone urbaine et péri-urbaine de Yaoundé. Les résultats de terrain montrent l'obtention de rendements et profits plus élevés lorsqu'on utilise le compost. Les résultats de la fonction de production Cobb-Douglas prouvent que l'utilisation du compost est statistiquement significative pour expliquer la variation de rendement de la laitue et que le compost est l'intrant le plus productif. D'autres résultats montrent que le compost fournit la matière organique utile au sol et que les besoins d'irrigation en eau de la culture sont réduits grâce à l'utilisation du compost. Par conséquent, malgré le fait que l'application du compost demande une main-d'oeuvre beaucoup plus élevée, son utilisation est généralement bénéfique pour les agriculteurs vivant aux alentours de Yaoundé. Les programmes de vulgarisation de cet intrant pour encourager son adoption devraient donc figurer parmi les points prioritaires dans la politique agricole du gouvernement camerounais.

  9. Physical modelling and testing in environmental geotechnics

    International Nuclear Information System (INIS)

    Garnier, J.; Thorel, L.; Haza, E.

    2000-01-01

    The preservation of natural environment has become a major concern, which affects nowadays a wide range of professionals from local communities administrators to natural resources managers (water, wildlife, flora, etc) and, in the end, to the consumers that we all are. Although totally ignored some fifty years ago, environmental geotechnics has become an emergent area of study and research which borders on the traditional domains, with which the geo-technicians are confronted (soil and rock mechanics, engineering geology, natural and anthropogenic risk management). Dedicated to experimental approaches (in-situ investigations and tests, laboratory tests, small-scale model testing), the Symposium fits in with the geotechnical domains of environment and transport of soil pollutants. These proceedings report some progress of developments in measurement techniques and studies of transport of pollutants in saturated and unsaturated soils in order to improve our understanding of such phenomena within multiphase environments. Experimental investigations on decontamination and isolation methods for polluted soils are discussed. The intention is to assess the impact of in-situ and laboratory tests, as well as small-scale model testing, on engineering practice. One paper is analysed in INIS data base for its specific interest in nuclear industry. The other ones, concerning the energy, are analyzed in ETDE data base

  10. Hypervapotron flow testing with rapid prototype models

    International Nuclear Information System (INIS)

    Driemeyer, D.; Hellwig, T.; Kubik, D.; Langenderfer, E.; Mantz, H.; McSmith, M.; Jones, B.; Butler, J.

    1995-01-01

    A flow test model of the inlet section of a three channel hypervapotron plate that has been proposed as a heat sink in the ITER divertor was prepared using a rapid prototyping stereolithography process that is widely used for component development in US industry. An existing water flow loop at the University of Illinois is being used for isothermal flow tests to collect pressure drop data for comparison with proposed vapotron friction factor correlations. Differential pressure measurements are taken, across the test section inlet manifold, the vapotron channel (about a seven inch length), the outlet manifold and the inlet-to-outlet. The differential pressures are currently measured with manometers. Tests were conducted at flow velocities from 1--10 m/s to cover the full range of ITER interest. A tap was also added for a small hypodermic needle to inject dye into the flow channel at several positions to examine the nature of the developing flow field at the entrance to the vapotron section. Follow-on flow tests are planned using a model with adjustable flow channel dimensions to permit more extensive pressure drop data to be collected. This information will be used to update vapotron design correlations for ITER

  11. Physical modelling and testing in environmental geotechnics

    Energy Technology Data Exchange (ETDEWEB)

    Garnier, J.; Thorel, L.; Haza, E. [Laboratoire Central des Ponts et Chaussees a Nantes, 44 - Nantes (France)

    2000-07-01

    The preservation of natural environment has become a major concern, which affects nowadays a wide range of professionals from local communities administrators to natural resources managers (water, wildlife, flora, etc) and, in the end, to the consumers that we all are. Although totally ignored some fifty years ago, environmental geotechnics has become an emergent area of study and research which borders on the traditional domains, with which the geo-technicians are confronted (soil and rock mechanics, engineering geology, natural and anthropogenic risk management). Dedicated to experimental approaches (in-situ investigations and tests, laboratory tests, small-scale model testing), the Symposium fits in with the geotechnical domains of environment and transport of soil pollutants. These proceedings report some progress of developments in measurement techniques and studies of transport of pollutants in saturated and unsaturated soils in order to improve our understanding of such phenomena within multiphase environments. Experimental investigations on decontamination and isolation methods for polluted soils are discussed. The intention is to assess the impact of in-situ and laboratory tests, as well as small-scale model testing, on engineering practice. One paper has been analyzed in INIS data base for its specific interest in nuclear industry.

  12. Horns Rev II, 2-D Model Tests

    DEFF Research Database (Denmark)

    Andersen, Thomas Lykke; Frigaard, Peter

    This report present the results of 2D physical model tests carried out in the shallow wave flume at Dept. of Civil Engineering, Aalborg University (AAU), on behalf of Energy E2 A/S part of DONG Energy A/S, Denmark. The objective of the tests was: to investigate the combined influence of the pile...... diameter to water depth ratio and the wave hight to water depth ratio on wave run-up of piles. The measurements should be used to design access platforms on piles....

  13. Temperature Buffer Test. Final THM modelling

    International Nuclear Information System (INIS)

    Aakesson, Mattias; Malmberg, Daniel; Boergesson, Lennart; Hernelind, Jan; Ledesma, Alberto; Jacinto, Abel

    2012-01-01

    The Temperature Buffer Test (TBT) is a joint project between SKB/ANDRA and supported by ENRESA (modelling) and DBE (instrumentation), which aims at improving the understanding and to model the thermo-hydro-mechanical behavior of buffers made of swelling clay submitted to high temperatures (over 100 deg C) during the water saturation process. The test has been carried out in a KBS-3 deposition hole at Aespoe HRL. It was installed during the spring of 2003. Two heaters (3 m long, 0.6 m diameter) and two buffer arrangements have been investigated: the lower heater was surrounded by bentonite only, whereas the upper heater was surrounded by a composite barrier, with a sand shield between the heater and the bentonite. The test was dismantled and sampled during the winter of 2009/2010. This report presents the final THM modelling which was resumed subsequent to the dismantling operation. The main part of this work has been numerical modelling of the field test. Three different modelling teams have presented several model cases for different geometries and different degree of process complexity. Two different numerical codes, Code B right and Abaqus, have been used. The modelling performed by UPC-Cimne using Code B right, has been divided in three subtasks: i) analysis of the response observed in the lower part of the test, by inclusion of a number of considerations: (a) the use of the Barcelona Expansive Model for MX-80 bentonite; (b) updated parameters in the vapour diffusive flow term; (c) the use of a non-conventional water retention curve for MX-80 at high temperature; ii) assessment of a possible relation between the cracks observed in the bentonite blocks in the upper part of TBT, and the cycles of suction and stresses registered in that zone at the start of the experiment; and iii) analysis of the performance, observations and interpretation of the entire test. It was however not possible to carry out a full THM analysis until the end of the test due to

  14. Temperature Buffer Test. Final THM modelling

    Energy Technology Data Exchange (ETDEWEB)

    Aakesson, Mattias; Malmberg, Daniel; Boergesson, Lennart; Hernelind, Jan [Clay Technology AB, Lund (Sweden); Ledesma, Alberto; Jacinto, Abel [UPC, Universitat Politecnica de Catalunya, Barcelona (Spain)

    2012-01-15

    The Temperature Buffer Test (TBT) is a joint project between SKB/ANDRA and supported by ENRESA (modelling) and DBE (instrumentation), which aims at improving the understanding and to model the thermo-hydro-mechanical behavior of buffers made of swelling clay submitted to high temperatures (over 100 deg C) during the water saturation process. The test has been carried out in a KBS-3 deposition hole at Aespoe HRL. It was installed during the spring of 2003. Two heaters (3 m long, 0.6 m diameter) and two buffer arrangements have been investigated: the lower heater was surrounded by bentonite only, whereas the upper heater was surrounded by a composite barrier, with a sand shield between the heater and the bentonite. The test was dismantled and sampled during the winter of 2009/2010. This report presents the final THM modelling which was resumed subsequent to the dismantling operation. The main part of this work has been numerical modelling of the field test. Three different modelling teams have presented several model cases for different geometries and different degree of process complexity. Two different numerical codes, Code{sub B}right and Abaqus, have been used. The modelling performed by UPC-Cimne using Code{sub B}right, has been divided in three subtasks: i) analysis of the response observed in the lower part of the test, by inclusion of a number of considerations: (a) the use of the Barcelona Expansive Model for MX-80 bentonite; (b) updated parameters in the vapour diffusive flow term; (c) the use of a non-conventional water retention curve for MX-80 at high temperature; ii) assessment of a possible relation between the cracks observed in the bentonite blocks in the upper part of TBT, and the cycles of suction and stresses registered in that zone at the start of the experiment; and iii) analysis of the performance, observations and interpretation of the entire test. It was however not possible to carry out a full THM analysis until the end of the test due to

  15. Observational tests of FRW world models

    International Nuclear Information System (INIS)

    Lahav, Ofer

    2002-01-01

    Observational tests for the cosmological principle are reviewed. Assuming the FRW metric we then summarize estimates of cosmological parameters from various datasets, in particular the cosmic microwave background and the 2dF galaxy redshift survey. These and other analyses suggest a best-fit Λ-cold dark matter model with Ω m = 1 - Ω l ∼ 0.3 and H 0 ∼ 70 km s -1 Mpc -1 . It is remarkable that different measurements converge to this 'concordance model', although it remains to be seen if the two main components of this model, the dark matter and the dark energy, are real entities or just 'epicycles'. We point out some open questions related to this fashionable model

  16. Preliminary Test for Constitutive Models of CAP

    Energy Technology Data Exchange (ETDEWEB)

    Choo, Yeon Joon; Hong, Soon Joon; Hwang, Su Hyun; Lee, Keo Hyung; Kim, Min Ki; Lee, Byung Chul [FNC Tech., Seoul (Korea, Republic of); Ha, Sang Jun; Choi, Hoon [Korea Electric Power Research Institute, Daejeon (Korea, Republic of)

    2010-05-15

    The development project for the domestic design code was launched to be used for the safety and performance analysis of pressurized light water reactors. As a part of this project, CAP (Containment Analysis Package) code has been developing for the containment safety and performance analysis side by side with SPACE. The CAP code treats three fields (vapor, continuous liquid and dispersed drop) for the assessment of containment specific phenomena, and is featured by assessment capabilities in multi-dimensional and lumped parameter thermal hydraulic cell. Thermal hydraulics solver was developed and has a significant progress now. Implementation of the well proven constitutive models and correlations are essential in other for a containment code to be used with the generalized or optimized purposes. Generally, constitutive equations are composed of interfacial and wall transport models and correlations. These equations are included in the source terms of the governing field equations. In order to develop the best model and correlation package of the CAP code, various models currently used in major containment analysis codes, such as GOTHIC, CONTAIN2.0 and CONTEMPT-LT are reviewed. Several models and correlations were incorporated for the preliminary test of CAP's performance and test results and future plans to improve the level of execution besides will be discussed in this paper

  17. Preliminary Test for Constitutive Models of CAP

    International Nuclear Information System (INIS)

    Choo, Yeon Joon; Hong, Soon Joon; Hwang, Su Hyun; Lee, Keo Hyung; Kim, Min Ki; Lee, Byung Chul; Ha, Sang Jun; Choi, Hoon

    2010-01-01

    The development project for the domestic design code was launched to be used for the safety and performance analysis of pressurized light water reactors. As a part of this project, CAP (Containment Analysis Package) code has been developing for the containment safety and performance analysis side by side with SPACE. The CAP code treats three fields (vapor, continuous liquid and dispersed drop) for the assessment of containment specific phenomena, and is featured by assessment capabilities in multi-dimensional and lumped parameter thermal hydraulic cell. Thermal hydraulics solver was developed and has a significant progress now. Implementation of the well proven constitutive models and correlations are essential in other for a containment code to be used with the generalized or optimized purposes. Generally, constitutive equations are composed of interfacial and wall transport models and correlations. These equations are included in the source terms of the governing field equations. In order to develop the best model and correlation package of the CAP code, various models currently used in major containment analysis codes, such as GOTHIC, CONTAIN2.0 and CONTEMPT-LT are reviewed. Several models and correlations were incorporated for the preliminary test of CAP's performance and test results and future plans to improve the level of execution besides will be discussed in this paper

  18. Business model stress testing : A practical approach to test the robustness of a business model

    NARCIS (Netherlands)

    Haaker, T.I.; Bouwman, W.A.G.A.; Janssen, W; de Reuver, G.A.

    Business models and business model innovation are increasingly gaining attention in practice as well as in academic literature. However, the robustness of business models (BM) is seldom tested vis-à-vis the fast and unpredictable changes in digital technologies, regulation and markets. The

  19. Divergence-based tests for model diagnostic

    Czech Academy of Sciences Publication Activity Database

    Hobza, Tomáš; Esteban, M. D.; Morales, D.; Marhuenda, Y.

    2008-01-01

    Roč. 78, č. 13 (2008), s. 1702-1710 ISSN 0167-7152 R&D Projects: GA MŠk 1M0572 Grant - others:Instituto Nacional de Estadistica (ES) MTM2006-05693 Institutional research plan: CEZ:AV0Z10750506 Keywords : goodness of fit * devergence statistics * GLM * model checking * bootstrap Subject RIV: BB - Applied Statistics, Operational Research Impact factor: 0.445, year: 2008 http://library.utia.cas.cz/separaty/2008/SI/hobza-divergence-based%20tests%20for%20model%20diagnostic.pdf

  20. Overload prevention in model supports for wind tunnel model testing

    Directory of Open Access Journals (Sweden)

    Anton IVANOVICI

    2015-09-01

    Full Text Available Preventing overloads in wind tunnel model supports is crucial to the integrity of the tested system. Results can only be interpreted as valid if the model support, conventionally called a sting remains sufficiently rigid during testing. Modeling and preliminary calculation can only give an estimate of the sting’s behavior under known forces and moments but sometimes unpredictable, aerodynamically caused model behavior can cause large transient overloads that cannot be taken into account at the sting design phase. To ensure model integrity and data validity an analog fast protection circuit was designed and tested. A post-factum analysis was carried out to optimize the overload detection and a short discussion on aeroelastic phenomena is included to show why such a detector has to be very fast. The last refinement of the concept consists in a fast detector coupled with a slightly slower one to differentiate between transient overloads that decay in time and those that are the result of aeroelastic unwanted phenomena. The decision to stop or continue the test is therefore conservatively taken preserving data and model integrity while allowing normal startup loads and transients to manifest.

  1. Designing healthy communities: Testing the walkability model

    OpenAIRE

    Zuniga-Teran, Adriana; Orr, Barron; Gimblett, Randy; Chalfoun, Nader; Marsh, Stuart; Guertin, David; Going, Scott

    2017-01-01

    Research from multiple domains has provided insights into how neighborhood design can be improved to have a more favorable effect on physical activity, a concept known as walkability. The relevant research findings/hypotheses have been integrated into a Walkability Framework, which organizes the design elements into nine walkability categories. The purpose of this study was to test whether this conceptual framework can be used as a model to measure the interactions between the built environme...

  2. 2-D Model Test of Dolosse Breakwater

    DEFF Research Database (Denmark)

    Burcharth, Hans F.; Liu, Zhou

    1994-01-01

    ). To extend the design diagram to cover Dolos breakwaters with superstructure, 2-D model tests of Dolos breakwater with wave wall is included in the project Rubble Mound Breakwater Failure Modes sponsored by the Directorate General XII of the Commission of the European Communities under Contract MAS-CT92......The rational design diagram for Dolos armour should incorporate both the hydraulic stability and the structural integrity. The previous tests performed by Aalborg University (AU) made available such design diagram for the trunk of Dolos breakwater without superstructures (Burcharth et al. 1992...... was on the Dolos breakwater with a high superstructure, where there was almost no overtopping. This case is believed to be the most dangerous one. The test of the Dolos breakwater with a low superstructure was also performed. The objective of the last part of the experiment is to investigate the influence...

  3. Picholine marocaine clones X Picholine du Languedoc

    African Journals Online (AJOL)

    SERVER

    2007-12-17

    Dec 17, 2007 ... marocaine" cultivar and the "Picholine du Languedoc" cultivar, the descendants and their parents were analysed using 35 ... marocaine" is the most dominant cultivar; more than 98% ... this proportion, a χ2 test was calculated to test the null hypothesis. ... a lethal or semi-lethal locus (Bradshaw and Stettler,.

  4. Inverse hydrochemical models of aqueous extracts tests

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, L.; Samper, J.; Montenegro, L.

    2008-10-10

    Aqueous extract test is a laboratory technique commonly used to measure the amount of soluble salts of a soil sample after adding a known mass of distilled water. Measured aqueous extract data have to be re-interpreted in order to infer porewater chemical composition of the sample because porewater chemistry changes significantly due to dilution and chemical reactions which take place during extraction. Here we present an inverse hydrochemical model to estimate porewater chemical composition from measured water content, aqueous extract, and mineralogical data. The model accounts for acid-base, redox, aqueous complexation, mineral dissolution/precipitation, gas dissolution/ex-solution, cation exchange and surface complexation reactions, of which are assumed to take place at local equilibrium. It has been solved with INVERSE-CORE{sup 2D} and been tested with bentonite samples taken from FEBEX (Full-scale Engineered Barrier EXperiment) in situ test. The inverse model reproduces most of the measured aqueous data except bicarbonate and provides an effective, flexible and comprehensive method to estimate porewater chemical composition of clays. Main uncertainties are related to kinetic calcite dissolution and variations in CO2(g) pressure.

  5. Renforcement de la lutte antitabac en Afrique du Sud | IDRC ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    affichage de mises en garde sur les produits du tabac (l'équipe doit encore proposer des messages, les soumettre à un groupe test et les évaluer) et de délimiter des zones sans fumée pour les spectateurs de la Coupe du monde de football de 2010.

  6. The model and photographer of the Portrait of a Woman submitted to the SFP in 1867 by Tessié du Motay and Maré

    OpenAIRE

    Van Houtven, Andrea

    2017-01-01

    Cet article identifie la femme assise du Portrait de femme comme étant Marguerite Arosa, fille de Gustave Arosa, qui a collaboré avec Tessié du Motay et Maréchal, les inventeurs d’un nouveau procédé de collotype, afin de créer la Société de Phototypie Arosa et Cie. Il examine la formation de ce partenariat via son acte de constitution, et en lien avec la présentation du procédé à l’Assemblée générale de la Société Française de Photographie en avril 1867 lors de l’annonce du lauréat du concour...

  7. Du Pont de Nemours

    NARCIS (Netherlands)

    Ros JPM; LAE

    1994-01-01

    Dit rapport over Du Pont de Nemours (produktie van o.a. chemische stoffen) is gepubliceerd binnen het Samenwerkingsproject Procesbeschrijvingen Industrie Nederland (SPIN). In het kader van dit project is informatie verzameld over industriele bedrijven of industriele processen ter ondersteuning

  8. Movable scour protection. Model test report

    Energy Technology Data Exchange (ETDEWEB)

    Lorenz, R.

    2002-07-01

    This report presents the results of a series of model tests with scour protection of marine structures. The objective of the model tests is to investigate the integrity of the scour protection during a general lowering of the surrounding seabed, for instance in connection with movement of a sand bank or with general subsidence. The scour protection in the tests is made out of stone material. Two different fractions have been used: 4 mm and 40 mm. Tests with current, with waves and with combined current and waves were carried out. The scour protection material was placed after an initial scour hole has evolved in the seabed around the structure. This design philosophy has been selected because the situation often is that the scour hole starts to generate immediately after the structure has been placed. It is therefore difficult to establish a scour protection at the undisturbed seabed if the scour material is placed after the main structure. Further, placing the scour material in the scour hole increases the stability of the material. Two types of structure have been used for the test, a Monopile and a Tripod foundation. Test with protection mats around the Monopile model was also carried out. The following main conclusions have emerged form the model tests with flat bed (i.e. no general seabed lowering): 1. The maximum scour depth found in steady current on sand bed was 1.6 times the cylinder diameter, 2. The minimum horizontal extension of the scour hole (upstream direction) was 2.8 times the cylinder diameter, corresponding to a slope of 30 degrees, 3. Concrete protection mats do not meet the criteria for a strongly erodible seabed. In the present test virtually no reduction in the scour depth was obtained. The main problem is the interface to the cylinder. If there is a void between the mats and the cylinder, scour will develop. Even with the protection mats that are tightly connected to the cylinder, scour is expected to develop as long as the mats allow for

  9. Thurstonian models for sensory discrimination tests as generalized linear models

    DEFF Research Database (Denmark)

    Brockhoff, Per B.; Christensen, Rune Haubo Bojesen

    2010-01-01

    as a so-called generalized linear model. The underlying sensory difference 6 becomes directly a parameter of the statistical model and the estimate d' and it's standard error becomes the "usual" output of the statistical analysis. The d' for the monadic A-NOT A method is shown to appear as a standard......Sensory discrimination tests such as the triangle, duo-trio, 2-AFC and 3-AFC tests produce binary data and the Thurstonian decision rule links the underlying sensory difference 6 to the observed number of correct responses. In this paper it is shown how each of these four situations can be viewed...

  10. Blast Testing and Modelling of Composite Structures

    DEFF Research Database (Denmark)

    Giversen, Søren

    The motivation for this work is based on a desire for finding light weight alternatives to high strength steel as the material to use for armouring in military vehicles. With the use of high strength steel, an increase in the level of armouring has a significant impact on the vehicle weight......, affecting for example the manoeuvrability and top speed negatively, which ultimately affects the safety of the personal in the vehicle. Strong and light materials, such as fibre reinforced composites, could therefore act as substitutes for the high strength steel, and minimize the impact on the vehicle...... work this set-up should be improved such that the modelled pressure can be validated. For tests performed with a 250g charge load comparisons with model data showed poor agreement. This was found to be due to improper design of the modelled laminate panels, where the layer interface delamination...

  11. BIOMOVS test scenario model comparison using BIOPATH

    International Nuclear Information System (INIS)

    Grogan, H.A.; Van Dorp, F.

    1986-07-01

    This report presents the results of the irrigation test scenario, presented in the BIOMOVS intercomparison study, calculated by the computer code BIOPATH. This scenario defines a constant release of Tc-99 and Np-237 into groundwater that is used for irrigation. The system of compartments used to model the biosphere is based upon an area in northern Switzerland and is essentially the same as that used in Projekt Gewaehr to assess the radiological impact of a high level waste repository. Two separate irrigation methods are considered, namely ditch and overhead irrigation. Their influence on the resultant activities calculated in the groundwater, soil and different foodproducts, as a function of time, is evaluated. The sensitivity of the model to parameter variations is analysed which allows a deeper understanding of the model chain. These results are assessed subjectively in a first effort to realistically quantify the uncertainty associated with each calculated activity. (author)

  12. Thermal modelling of Advanced LIGO test masses

    International Nuclear Information System (INIS)

    Wang, H; Dovale Álvarez, M; Mow-Lowry, C M; Freise, A; Blair, C; Brooks, A; Kasprzack, M F; Ramette, J; Meyers, P M; Kaufer, S; O’Reilly, B

    2017-01-01

    High-reflectivity fused silica mirrors are at the epicentre of today’s advanced gravitational wave detectors. In these detectors, the mirrors interact with high power laser beams. As a result of finite absorption in the high reflectivity coatings the mirrors suffer from a variety of thermal effects that impact on the detectors’ performance. We propose a model of the Advanced LIGO mirrors that introduces an empirical term to account for the radiative heat transfer between the mirror and its surroundings. The mechanical mode frequency is used as a probe for the overall temperature of the mirror. The thermal transient after power build-up in the optical cavities is used to refine and test the model. The model provides a coating absorption estimate of 1.5–2.0 ppm and estimates that 0.3 to 1.3 ppm of the circulating light is scattered onto the ring heater. (paper)

  13. Les Cahiers du CREAD

    African Journals Online (AJOL)

    Admin

    6 juil. 2007 ... La problématique du développement du secteur de l'artisanat en. Algérie a été très peu abordée par les chercheurs, qu'ils soient universitaires ou .... La loi a institué une taxe d'apprentissage dont le taux a été fixé à. 1% de la ...

  14. Les outils du CERN

    CERN Multimedia

    1999-01-01

    C'est le plus grand centre mondial de recherche en physique des particules. Les outils du Laboratoire, accélérateurs et détecteurs de particules, figurent parmi les instruments scientifiques les plus complexes au monde. Des prix Nobels ont d'ailleurs été attribués aux physiciens du CERN pour leurs développements.

  15. Bulletin du CRDI #127

    International Development Research Centre (IDRC) Digital Library (Canada)

    La mise à l'échelle de la recherche et de l'innovation en vue de créer un impact social constitue une priorité pour la communauté du développement. Toutefois ... Nous avons renouvelé notre soutien à la recherche auprès du gouvernement de l'Inde ... Des femmes étudient à l'École supérieure d'infotronique d'Haïti.

  16. Testing substellar models with dynamical mass measurements

    Directory of Open Access Journals (Sweden)

    Liu M.C.

    2011-07-01

    Full Text Available We have been using Keck laser guide star adaptive optics to monitor the orbits of ultracool binaries, providing dynamical masses at lower luminosities and temperatures than previously available and enabling strong tests of theoretical models. We have identified three specific problems with theory: (1 We find that model color–magnitude diagrams cannot be reliably used to infer masses as they do not accurately reproduce the colors of ultracool dwarfs of known mass. (2 Effective temperatures inferred from evolutionary model radii are typically inconsistent with temperatures derived from fitting atmospheric models to observed spectra by 100–300 K. (3 For the only known pair of field brown dwarfs with a precise mass (3% and age determination (≈25%, the measured luminosities are ~2–3× higher than predicted by model cooling rates (i.e., masses inferred from Lbol and age are 20–30% larger than measured. To make progress in understanding the observed discrepancies, more mass measurements spanning a wide range of luminosity, temperature, and age are needed, along with more accurate age determinations (e.g., via asteroseismology for primary stars with brown dwarf binary companions. Also, resolved optical and infrared spectroscopy are needed to measure lithium depletion and to characterize the atmospheres of binary components in order to better assess model deficiencies.

  17. Seepage Calibration Model and Seepage Testing Data

    International Nuclear Information System (INIS)

    Dixon, P.

    2004-01-01

    The purpose of this Model Report is to document the Seepage Calibration Model (SCM). The SCM is developed (1) to establish the conceptual basis for the Seepage Model for Performance Assessment (SMPA), and (2) to derive seepage-relevant, model-related parameters and their distributions for use in the SMPA and seepage abstraction in support of the Total System Performance Assessment for License Application (TSPA-LA). The SCM is intended to be used only within this Model Report for the estimation of seepage-relevant parameters through calibration of the model against seepage-rate data from liquid-release tests performed in several niches along the Exploratory Studies Facility (ESF) Main Drift and in the Cross Drift. The SCM does not predict seepage into waste emplacement drifts under thermal or ambient conditions. Seepage predictions for waste emplacement drifts under ambient conditions will be performed with the SMPA (see upcoming REV 02 of CRWMS M and O 2000 [153314]), which inherits the conceptual basis and model-related parameters from the SCM. Seepage during the thermal period is examined separately in the Thermal Hydrologic (TH) Seepage Model (see BSC 2003 [161530]). The scope of this work is (1) to evaluate seepage rates measured during liquid-release experiments performed in several niches in the Exploratory Studies Facility (ESF) and in the Cross Drift, which was excavated for enhanced characterization of the repository block (ECRB); (2) to evaluate air-permeability data measured in boreholes above the niches and the Cross Drift to obtain the permeability structure for the seepage model; (3) to use inverse modeling to calibrate the SCM and to estimate seepage-relevant, model-related parameters on the drift scale; (4) to estimate the epistemic uncertainty of the derived parameters, based on the goodness-of-fit to the observed data and the sensitivity of calculated seepage with respect to the parameters of interest; (5) to characterize the aleatory uncertainty

  18. Large scale injection test (LASGIT) modelling

    International Nuclear Information System (INIS)

    Arnedo, D.; Olivella, S.; Alonso, E.E.

    2010-01-01

    Document available in extended abstract form only. With the objective of understanding the gas flow processes through clay barriers in schemes of radioactive waste disposal, the Lasgit in situ experiment was planned and is currently in progress. The modelling of the experiment will permit to better understand of the responses, to confirm hypothesis of mechanisms and processes and to learn in order to design future experiments. The experiment and modelling activities are included in the project FORGE (FP7). The in situ large scale injection test Lasgit is currently being performed at the Aespoe Hard Rock Laboratory by SKB and BGS. An schematic layout of the test is shown. The deposition hole follows the KBS3 scheme. A copper canister is installed in the axe of the deposition hole, surrounded by blocks of highly compacted MX-80 bentonite. A concrete plug is placed at the top of the buffer. A metallic lid anchored to the surrounding host rock is included in order to prevent vertical movements of the whole system during gas injection stages (high gas injection pressures are expected to be reached). Hydration of the buffer material is achieved by injecting water through filter mats, two placed at the rock walls and two at the interfaces between bentonite blocks. Water is also injected through the 12 canister filters. Gas injection stages are performed injecting gas to some of the canister injection filters. Since the water pressure and the stresses (swelling pressure development) will be high during gas injection, it is necessary to inject at high gas pressures. This implies mechanical couplings as gas penetrates after the gas entry pressure is achieved and may produce deformations which in turn lead to permeability increments. A 3D hydro-mechanical numerical model of the test using CODE-BRIGHT is presented. The domain considered for the modelling is shown. The materials considered in the simulation are the MX-80 bentonite blocks (cylinders and rings), the concrete plug

  19. Adversarial life testing: A Bayesian negotiation model

    International Nuclear Information System (INIS)

    Rufo, M.J.; Martín, J.; Pérez, C.J.

    2014-01-01

    Life testing is a procedure intended for facilitating the process of making decisions in the context of industrial reliability. On the other hand, negotiation is a process of making joint decisions that has one of its main foundations in decision theory. A Bayesian sequential model of negotiation in the context of adversarial life testing is proposed. This model considers a general setting for which a manufacturer offers a product batch to a consumer. It is assumed that the reliability of the product is measured in terms of its lifetime. Furthermore, both the manufacturer and the consumer have to use their own information with respect to the quality of the product. Under these assumptions, two situations can be analyzed. For both of them, the main aim is to accept or reject the product batch based on the product reliability. This topic is related to a reliability demonstration problem. The procedure is applied to a class of distributions that belong to the exponential family. Thus, a unified framework addressing the main topics in the considered Bayesian model is presented. An illustrative example shows that the proposed technique can be easily applied in practice

  20. Contribution à l'optimisation du carottage par modélisation de l'initialisation du discage Contribution to the Optimizing of Core Drilling by Modeling the Initiation of Discing

    Directory of Open Access Journals (Sweden)

    Venet V.

    2006-11-01

    Full Text Available L'étude du discage des carottes pétrolières peut être utilisée, soit : - quand il survient, comme un indicateur des contraintes in situ; - comme un moyen d'optimiser le carottage en vue de l'obtention de carottes intactes pour les essais en laboratoire. Nous n'aborderons dans cet article que le dernier aspect du problème. Dans un premier temps, nous dégagerons, à partir d'une étude bibliographique, les principaux paramètres qui influent sur le discage. Le logiciel DISCAGELF (éléments finis en symétrie de révolution sera ensuite décrit succinctement. Il inclut un mailleur automatique et une possibilité d'effectuer une loupe sur la zone à haute probabilité de rupture pour assurer son accessibilité et son implantation éventuelle sur des micro-ordinateurs (type PC. Une validation de ce logiciel à partir d'essais réalisés sur le Triaxial vrai de Lille et sur la cellule à disquer de l'Institut National pour l'Environnement et les Risques (INERIS (avec ou sans simulation de pression de boue a ensuite été effectuée. Dans la quatrième partie de cet article, nous présenterons les résultats essentiels, provenant de plus de 200 simulations numériques, relatifs à l'influence des paramètres : caractéristiques géomécaniques du matériau, densité de boue, poids sur l'outil, type et géométrie de l'outil de carottage, sur les contraintes d'amorce de la rupture. Nous avons ainsi mis en évidence l'existence : - d'un domaine de sécurité vis-à-vis de l'amorce de la rupture ; - de relations linéaires entre les contraintes radiales d'amorce de la rupture d'une part, et les caractéristiques géomécaniques du matériau et la densité de la boue d'autre part ; - de quatre positions préférentielles du point d'amorce de la rupture pour lesquels le mécanisme engendrant la rupture est différent ; - de l'influence du type et de la géométrie du carottier sur l'amorce de la rupture et sur la courbure des disques potentiels

  1. Consistency test of the standard model

    International Nuclear Information System (INIS)

    Pawlowski, M.; Raczka, R.

    1997-01-01

    If the 'Higgs mass' is not the physical mass of a real particle but rather an effective ultraviolet cutoff then a process energy dependence of this cutoff must be admitted. Precision data from at least two energy scale experimental points are necessary to test this hypothesis. The first set of precision data is provided by the Z-boson peak experiments. We argue that the second set can be given by 10-20 GeV e + e - colliders. We pay attention to the special role of tau polarization experiments that can be sensitive to the 'Higgs mass' for a sample of ∼ 10 8 produced tau pairs. We argue that such a study may be regarded as a negative selfconsistency test of the Standard Model and of most of its extensions

  2. Tests on thirteen navy type model propellers

    Science.gov (United States)

    Durand, W F

    1927-01-01

    The tests on these model propellers were undertaken for the purpose of determining the performance coefficients and characteristics for certain selected series of propellers of form and type as commonly used in recent navy designs. The first series includes seven propellers of pitch ratio varying by 0.10 to 1.10, the area, form of blade, thickness, etc., representing an arbitrary standard propeller which had shown good results. The second series covers changes in thickness of blade section, other things equal, and the third series, changes in blade area, other things equal. These models are all of 36-inch diameter. Propellers A to G form the series on pitch ratio, C, N. I. J the series on thickness of section, and K, M, C, L the series on area. (author)

  3. Seepage Calibration Model and Seepage Testing Data

    Energy Technology Data Exchange (ETDEWEB)

    S. Finsterle

    2004-09-02

    The purpose of this Model Report is to document the Seepage Calibration Model (SCM). The SCM was developed (1) to establish the conceptual basis for the Seepage Model for Performance Assessment (SMPA), and (2) to derive seepage-relevant, model-related parameters and their distributions for use in the SMPA and seepage abstraction in support of the Total System Performance Assessment for License Application (TSPA-LA). This Model Report has been revised in response to a comprehensive, regulatory-focused evaluation performed by the Regulatory Integration Team [''Technical Work Plan for: Regulatory Integration Evaluation of Analysis and Model Reports Supporting the TSPA-LA'' (BSC 2004 [DIRS 169653])]. The SCM is intended to be used only within this Model Report for the estimation of seepage-relevant parameters through calibration of the model against seepage-rate data from liquid-release tests performed in several niches along the Exploratory Studies Facility (ESF) Main Drift and in the Cross-Drift. The SCM does not predict seepage into waste emplacement drifts under thermal or ambient conditions. Seepage predictions for waste emplacement drifts under ambient conditions will be performed with the SMPA [''Seepage Model for PA Including Drift Collapse'' (BSC 2004 [DIRS 167652])], which inherits the conceptual basis and model-related parameters from the SCM. Seepage during the thermal period is examined separately in the Thermal Hydrologic (TH) Seepage Model [see ''Drift-Scale Coupled Processes (DST and TH Seepage) Models'' (BSC 2004 [DIRS 170338])]. The scope of this work is (1) to evaluate seepage rates measured during liquid-release experiments performed in several niches in the Exploratory Studies Facility (ESF) and in the Cross-Drift, which was excavated for enhanced characterization of the repository block (ECRB); (2) to evaluate air-permeability data measured in boreholes above the niches and the Cross

  4. Seepage Calibration Model and Seepage Testing Data

    International Nuclear Information System (INIS)

    Finsterle, S.

    2004-01-01

    The purpose of this Model Report is to document the Seepage Calibration Model (SCM). The SCM was developed (1) to establish the conceptual basis for the Seepage Model for Performance Assessment (SMPA), and (2) to derive seepage-relevant, model-related parameters and their distributions for use in the SMPA and seepage abstraction in support of the Total System Performance Assessment for License Application (TSPA-LA). This Model Report has been revised in response to a comprehensive, regulatory-focused evaluation performed by the Regulatory Integration Team [''Technical Work Plan for: Regulatory Integration Evaluation of Analysis and Model Reports Supporting the TSPA-LA'' (BSC 2004 [DIRS 169653])]. The SCM is intended to be used only within this Model Report for the estimation of seepage-relevant parameters through calibration of the model against seepage-rate data from liquid-release tests performed in several niches along the Exploratory Studies Facility (ESF) Main Drift and in the Cross-Drift. The SCM does not predict seepage into waste emplacement drifts under thermal or ambient conditions. Seepage predictions for waste emplacement drifts under ambient conditions will be performed with the SMPA [''Seepage Model for PA Including Drift Collapse'' (BSC 2004 [DIRS 167652])], which inherits the conceptual basis and model-related parameters from the SCM. Seepage during the thermal period is examined separately in the Thermal Hydrologic (TH) Seepage Model [see ''Drift-Scale Coupled Processes (DST and TH Seepage) Models'' (BSC 2004 [DIRS 170338])]. The scope of this work is (1) to evaluate seepage rates measured during liquid-release experiments performed in several niches in the Exploratory Studies Facility (ESF) and in the Cross-Drift, which was excavated for enhanced characterization of the repository block (ECRB); (2) to evaluate air-permeability data measured in boreholes above the niches and the Cross-Drift to obtain the permeability structure for the seepage model

  5. Ultrasonic testing of canning tubes in stainless steel of the EL 4 reactor; Controle par ultrasons des tubes de gaine en acier inoxydable du reacteur EL 4

    Energy Technology Data Exchange (ETDEWEB)

    Prot, A; Monnier, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    From all the methods possible for controlling thin cans the one chosen, for numerous reasons, vas that making use of ultrasonic techniques. A method has been developed which should make it possible to carry out a rapid and efficient industrial control of canning tubes, The reasons for the choice of the ultrasonic method are given in detail, together with the principles of the method and the actual control parameters. In the present state of our research, it should be possible to control at least 50 000 tubes a year. Improvements brought about in the details of the control technique itself should make it possible to increase this rate considerably. (authors) [French] Parmi toutes les methodes possibles de controle des gaines minces, le procede retenu pour de multiples raisons a ete celui faisant appel a la technique des ultrasons. Une methode a ete mise au point qui doit permettre un controle industriel rapide et efficace des tubes de gaine. Sont exposes en detail, les raisons du choix de la methode par ultrasons, les principes de cette methode et les parametres du controle proprement dit. Dans l'etat actuel de nos etudes la cadence devrait permettre le controle de 50000 tubes par an au minimum. Des ameliorations de detail portant sur la technique de controle elle-meme, doivent permettre d'accelerer tres notablement cette cadence. (auteurs)

  6. Effet du Pediococcus acidilactici sur le bilan lipidique sanguin du ...

    African Journals Online (AJOL)

    Les résultats relatifs aux performances zootechniques ont montré que l'addition du probiotique a amélioré significativement le gain de poids pendant la phase de croissance se traduisant par un indice de consommation meilleur. Les dosages du cholestérol total, des triglycérides, du HDL et du LDL ont été déterminés à la ...

  7. Model-Based Software Testing for Object-Oriented Software

    Science.gov (United States)

    Biju, Soly Mathew

    2008-01-01

    Model-based testing is one of the best solutions for testing object-oriented software. It has a better test coverage than other testing styles. Model-based testing takes into consideration behavioural aspects of a class, which are usually unchecked in other testing methods. An increase in the complexity of software has forced the software industry…

  8. Pertinence de l’utilisation du modèle de Toulmin dans l’analyse de corpus The relevance of Toulmin’s model in case studies

    Directory of Open Access Journals (Sweden)

    Emmanuel de Jonge

    2008-09-01

    la Seconde Guerre Mondiale constituera un anti-exemple dans lequel il faut puiser les moyens d’éviter la reproduction de l’événement. Nous utiliserons le terme de désenchantement pour qualifier cette disposition psycho-cognitive qui affecte toute la rhétorique. Au niveau des discours d’opposition, on constate une immixtion du génocide dans le politique, que ce soit dans les discours négationnistes, théories du complot, ou dans les discours sur l’esclavage, mettant en jeu une concurrence des victimes. La méthode d’analyse toulminienne permet cet éclairage, et établit ainsi un lien essentiel entre la rhétorique et l’analyse du discours.How can we use Toulmin’s model in the analysis of specific case studies? It seems that it has been almost exclusively used for either discussions in logical reasoning, or for theoretical discussions about probability. In this article, I want to show that Toulmin’s model can be very useful for Discourse Analysis since it allows the analyst to extract mostly implicit warrants and backings. In my view, the notion of backing is related, on the one hand, to its technical argumentative side, and on the other hand, to the psycho-cognitive foundation of any reasoning, linked both to cognitive dispositions and to cultural factors. The Toulminian analysis thus proves to be very interesting when discussing deep-level arguments in a text. The article is divided into two sections. The first one is devoted to a comparative analysis of three Declarations: the 1776 American Declaration of Independence, the 1789 Declaration of the Rights of Man and the Citizen, and the 1948 Universal Declaration of Human Rights. I assume that the declarations constitute the linguistic expression of the deep-level or “backing” of society’s discourses. They show which warrants the argumentation is based on, in other words, on the basis of which values the society is going to argue. In the specific context of democracies concerned with

  9. Experimentally testing the standard cosmological model

    Energy Technology Data Exchange (ETDEWEB)

    Schramm, D.N. (Chicago Univ., IL (USA) Fermi National Accelerator Lab., Batavia, IL (USA))

    1990-11-01

    The standard model of cosmology, the big bang, is now being tested and confirmed to remarkable accuracy. Recent high precision measurements relate to the microwave background; and big bang nucleosynthesis. This paper focuses on the latter since that relates more directly to high energy experiments. In particular, the recent LEP (and SLC) results on the number of neutrinos are discussed as a positive laboratory test of the standard cosmology scenario. Discussion is presented on the improved light element observational data as well as the improved neutron lifetime data. alternate nucleosynthesis scenarios of decaying matter or of quark-hadron induced inhomogeneities are discussed. It is shown that when these scenarios are made to fit the observed abundances accurately, the resulting conclusions on the baryonic density relative to the critical density, {Omega}{sub b}, remain approximately the same as in the standard homogeneous case, thus, adding to the robustness of the standard model conclusion that {Omega}{sub b} {approximately} 0.06. This latter point is the deriving force behind the need for non-baryonic dark matter (assuming {Omega}{sub total} = 1) and the need for dark baryonic matter, since {Omega}{sub visible} < {Omega}{sub b}. Recent accelerator constraints on non-baryonic matter are discussed, showing that any massive cold dark matter candidate must now have a mass M{sub x} {approx gt} 20 GeV and an interaction weaker than the Z{sup 0} coupling to a neutrino. It is also noted that recent hints regarding the solar neutrino experiments coupled with the see-saw model for {nu}-masses may imply that the {nu}{sub {tau}} is a good hot dark matter candidate. 73 refs., 5 figs.

  10. Experimentally testing the standard cosmological model

    International Nuclear Information System (INIS)

    Schramm, D.N.

    1990-11-01

    The standard model of cosmology, the big bang, is now being tested and confirmed to remarkable accuracy. Recent high precision measurements relate to the microwave background; and big bang nucleosynthesis. This paper focuses on the latter since that relates more directly to high energy experiments. In particular, the recent LEP (and SLC) results on the number of neutrinos are discussed as a positive laboratory test of the standard cosmology scenario. Discussion is presented on the improved light element observational data as well as the improved neutron lifetime data. alternate nucleosynthesis scenarios of decaying matter or of quark-hadron induced inhomogeneities are discussed. It is shown that when these scenarios are made to fit the observed abundances accurately, the resulting conclusions on the baryonic density relative to the critical density, Ω b , remain approximately the same as in the standard homogeneous case, thus, adding to the robustness of the standard model conclusion that Ω b ∼ 0.06. This latter point is the deriving force behind the need for non-baryonic dark matter (assuming Ω total = 1) and the need for dark baryonic matter, since Ω visible b . Recent accelerator constraints on non-baryonic matter are discussed, showing that any massive cold dark matter candidate must now have a mass M x approx-gt 20 GeV and an interaction weaker than the Z 0 coupling to a neutrino. It is also noted that recent hints regarding the solar neutrino experiments coupled with the see-saw model for ν-masses may imply that the ν τ is a good hot dark matter candidate. 73 refs., 5 figs

  11. Development and Testing of Xanthan Products for Eor-Applications in the North Sea Développement et essais des produits à base de xanthane pour les applications de RAH en mer du Nord

    Directory of Open Access Journals (Sweden)

    Foss P.

    2006-11-01

    Full Text Available A program for development and evaluation of xanthan for use in enhanced oil recovery projects in the North Sea has been performed. Xanthan was produced using different fermentation conditions. Rheological measurements and filterability tests have been done. Xanthan products, which readily dissolve in sea water and give high viscosity and low aggregation have been produced. The fermentation process used for this type of product was scaled up from 10 litres to 20,000 litres production volume without significant changes in polymer solution properties. Un programme de développement et d'évaluation du xanthane pour utilisation dans les projets de récupération assistée des hydrocarbures en mer du Nord a été réalisé. Le xanthane est obtenu par différents procédés de fermentation. On a effectué des mesures rhéologiques et des essais de filtrabilité. Les produits à base de xanthane se dissolvent facilement dans l'eau de mer, ils donnent une forte viscosité et une faible agrégation. Avec le procédé de fermentation utilisé pour ce type de produit, on a pu faire passer la production de 10 litres à 20000 litres sans modification notable des propriétés de la solution de polymère.

  12. Un protocole pour la modélisation du fonctionnement des stations d'épuration à boues activées GMP Protocol for activated sludge models

    Directory of Open Access Journals (Sweden)

    GILLOT, Sylvie ; LANGERGRABER, Günter ; OHTSUKI, Takayuki ; SHAW, Andrew ; TAKACS, Imre ; WINKLER, Stefan ; RIEGER, Leiv

    2012-12-01

    Full Text Available Les stations d’épuration sont des systèmes dynamiques, soumis à d’importantes variations temporelles. La modélisation de leur fonctionnement, qui consiste à représenter mathématiquement l’évolution dans le temps de variables d’intérêt représentant les phénomènes biologiques, physiques et chimiques qui se déroulent dans les ouvrages, est utilisée pour mieux comprendre les processus mis en jeu et optimiser le traitement des eaux résiduaires.. Focus sur les activités du groupe de travail Good Modelling Practice de l’IWA, auquel participe activement les équipes d’Irstea, notamment dans l’élaboration d’un protocole pour l’utilisation des modèles de boues activées en pratique.The IWA Task Group on Good Modelling Practice (GMP has analysed current practice and experience on the use of activated sludge models. The group developed a framework to make modelling more straightforward and that helps structuring the interaction between modellers and the project stakeholders. The GMP protocol is a synthesis of existing procedures, and contains five major steps: (i Project definition, (ii Data collection and reconciliation, (iii Plant model set-up, (iv Calibration and validation, and (v Simulation and result interpretation. The Unified Protocol forms the basis of a Scientific and Technical Report that will be published in late 2012.

  13. Testing an integral conceptual model of frailty.

    Science.gov (United States)

    Gobbens, Robbert J; van Assen, Marcel A; Luijkx, Katrien G; Schols, Jos M

    2012-09-01

    This paper is a report of a study conducted to test three hypotheses derived from an integral conceptual model of frailty.   The integral model of frailty describes the pathway from life-course determinants to frailty to adverse outcomes. The model assumes that life-course determinants and the three domains of frailty (physical, psychological, social) affect adverse outcomes, the effect of disease(s) on adverse outcomes is mediated by frailty, and the effect of frailty on adverse outcomes depends on the life-course determinants. In June 2008 a questionnaire was sent to a sample of community-dwelling people, aged 75 years and older (n = 213). Life-course determinants and frailty were assessed using the Tilburg frailty indicator. Adverse outcomes were measured using the Groningen activity restriction scale, the WHOQOL-BREF and questions regarding healthcare utilization. The effect of seven self-reported chronic diseases was examined. Life-course determinants, chronic disease(s), and frailty together explain a moderate to large part of the variance of the seven continuous adverse outcomes (26-57%). All these predictors together explained a significant part of each of the five dichotomous adverse outcomes. The effect of chronic disease(s) on all 12 adverse outcomes was mediated at least partly by frailty. The effect of frailty domains on adverse outcomes did not depend on life-course determinants. Our finding that the adverse outcomes are differently and uniquely affected by the three domains of frailty (physical, psychological, social), and life-course determinants and disease(s), emphasizes the importance of an integral conceptual model of frailty. © 2011 Blackwell Publishing Ltd.

  14. Les mots du jazz

    OpenAIRE

    Roueff, Olivier

    2007-01-01

    L’ouvrage d’André Schaeffner constitue la première analyse savante du jazz (1926). Il a marqué une étape importante dans le processus de réinvention du jazz en France en contribuant notamment, par sa réception et les polémiques qu’il a suscitées, à transformer l’identification du jazz d’une musique « américaine » à une musique « noire-américaine » (c’est-à-dire aux « racines » africaines). Les analyses proposées dans cet ouvrage, alors qu’elles désignaient des musiques que la critique de jazz...

  15. Pion interferometric tests of transport models

    Energy Technology Data Exchange (ETDEWEB)

    Padula, S.S.; Gyulassy, M.; Gavin, S. (Lawrence Berkeley Lab., CA (USA). Nuclear Science Div.)

    1990-01-08

    In hadronic reactions, the usual space-time interpretation of pion interferometry often breaks down due to strong correlations between spatial and momentum coordinates. We derive a general interferometry formula based on the Wigner density formalism that allows for arbitrary phase space and multiparticle correlations. Correction terms due to intermediate state pion cascading are derived using semiclassical hadronic transport theory. Finite wave packets are used to reveal the sensitivity of pion interference effects on the details of the production dynamics. The covariant generalization of the formula is shown to be equivalent to the formula derived via an alternate current ensemble formalism for minimal wave packets and reduces in the nonrelativistic limit to a formula derived by Pratt. The final expression is ideally suited for pion interferometric tests of Monte Carlo transport models. Examples involving gaussian and inside-outside phase space distributions are considered. (orig.).

  16. Pion interferometric tests of transport models

    International Nuclear Information System (INIS)

    Padula, S.S.; Gyulassy, M.; Gavin, S.

    1990-01-01

    In hadronic reactions, the usual space-time interpretation of pion interferometry often breaks down due to strong correlations between spatial and momentum coordinates. We derive a general interferometry formula based on the Wigner density formalism that allows for arbitrary phase space and multiparticle correlations. Correction terms due to intermediate state pion cascading are derived using semiclassical hadronic transport theory. Finite wave packets are used to reveal the sensitivity of pion interference effects on the details of the production dynamics. The covariant generalization of the formula is shown to be equivalent to the formula derived via an alternate current ensemble formalism for minimal wave packets and reduces in the nonrelativistic limit to a formula derived by Pratt. The final expression is ideally suited for pion interferometric tests of Monte Carlo transport models. Examples involving gaussian and inside-outside phase space distributions are considered. (orig.)

  17. Experimental Tests of the Algebraic Cluster Model

    Science.gov (United States)

    Gai, Moshe

    2018-02-01

    The Algebraic Cluster Model (ACM) of Bijker and Iachello that was proposed already in 2000 has been recently applied to 12C and 16O with much success. We review the current status in 12C with the outstanding observation of the ground state rotational band composed of the spin-parity states of: 0+, 2+, 3-, 4± and 5-. The observation of the 4± parity doublet is a characteristic of (tri-atomic) molecular configuration where the three alpha- particles are arranged in an equilateral triangular configuration of a symmetric spinning top. We discuss future measurement with electron scattering, 12C(e,e’) to test the predicted B(Eλ) of the ACM.

  18. Two Bayesian tests of the GLOMOsys Model.

    Science.gov (United States)

    Field, Sarahanne M; Wagenmakers, Eric-Jan; Newell, Ben R; Zeelenberg, René; van Ravenzwaaij, Don

    2016-12-01

    Priming is arguably one of the key phenomena in contemporary social psychology. Recent retractions and failed replication attempts have led to a division in the field between proponents and skeptics and have reinforced the importance of confirming certain priming effects through replication. In this study, we describe the results of 2 preregistered replication attempts of 1 experiment by Förster and Denzler (2012). In both experiments, participants first processed letters either globally or locally, then were tested using a typicality rating task. Bayes factor hypothesis tests were conducted for both experiments: Experiment 1 (N = 100) yielded an indecisive Bayes factor of 1.38, indicating that the in-lab data are 1.38 times more likely to have occurred under the null hypothesis than under the alternative. Experiment 2 (N = 908) yielded a Bayes factor of 10.84, indicating strong support for the null hypothesis that global priming does not affect participants' mean typicality ratings. The failure to replicate this priming effect challenges existing support for the GLOMO sys model. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

  19. Experimental tests of the standard model

    International Nuclear Information System (INIS)

    Nodulman, L.

    1998-01-01

    The title implies an impossibly broad field, as the Standard Model includes the fermion matter states, as well as the forces and fields of SU(3) x SU(2) x U(1). For practical purposes, I will confine myself to electroweak unification, as discussed in the lectures of M. Herrero. Quarks and mixing were discussed in the lectures of R. Aleksan, and leptons and mixing were discussed in the lectures of K. Nakamura. I will essentially assume universality, that is flavor independence, rather than discussing tests of it. I will not pursue tests of QED beyond noting the consistency and precision of measurements of α EM in various processes including the Lamb shift, the anomalous magnetic moment (g-2) of the electron, and the quantum Hall effect. The fantastic precision and agreement of these predictions and measurements is something that convinces people that there may be something to this science enterprise. Also impressive is the success of the ''Universal Fermi Interaction'' description of beta decay processes, or in more modern parlance, weak charged current interactions. With one coupling constant G F , most precisely determined in muon decay, a huge number of nuclear instabilities are described. The slightly slow rate for neutron beta decay was one of the initial pieces of evidence for Cabbibo mixing, now generalized so that all charged current decays of any flavor are covered

  20. Computerized Classification Testing with the Rasch Model

    Science.gov (United States)

    Eggen, Theo J. H. M.

    2011-01-01

    If classification in a limited number of categories is the purpose of testing, computerized adaptive tests (CATs) with algorithms based on sequential statistical testing perform better than estimation-based CATs (e.g., Eggen & Straetmans, 2000). In these computerized classification tests (CCTs), the Sequential Probability Ratio Test (SPRT) (Wald,…

  1. fibrosarcome du larynx

    African Journals Online (AJOL)

    pie du lit tumoral est employée comme complément thé- rapeutique [9] alors que la chimiothérapie est générale- ment indiquée dans les formes métastatiques. Le pronos- tic dépend essentiellement du degré de différentiation his- tologique. En fait, le fibrosarcome bien différencié est caractérisé par la fréquence de récidive ...

  2. du Chott Marouane

    African Journals Online (AJOL)

    plancton de 90 µm de vide de maille. Ils ont été conservés dans du formol à 5%. L'identification de l'espèce est basée sur des critères morphologiques [20]: la forme des furcas, les lobes frontaux des antennes des mâles, de l'organe copulateur (pénis) et du sac ovigère. Le comptage des soies furcales a été réalisé. L'étude ...

  3. Cirque du Monde as a health intervention

    Science.gov (United States)

    Fournier, Cynthia; Drouin, Mélodie-Anne; Marcoux, Jérémie; Garel, Patricia; Bochud, Emmanuel; Théberge, Julie; Aubertin, Patrice; Favreau, Gil; Fleet, Richard

    2014-01-01

    Abstract Objective To present Cirque du Soleil’s social circus program, Cirque du Monde, to explore its potential as a primary health care tool for family physicians. Data sources A review of the literature in PubMed, the Cochrane Library, PsycINFO, LaPresse, Eureka, Google Scholar, and Érudit using the key words circus, social circus, Cirque du Monde, and Cirque du Soleil; a Montreal-based initiative, Espace Transition, modeled on Cirque du Monde; and personal communication with Cirque du Soleil’s Social Circus Training Advisor. Study selection The first 50 articles or websites identified for each key word in each of the databases were examined on the basis of their titles and abstracts in the case of articles, and on the basis of their titles and page content in the case of websites. Articles and websites that explored an aspect of social circuses or that described an intervention that involved circuses were then retained for analysis. Because all literature on social circuses was searched, no criterion for year of publication was used. Synthesis No articles on the social circus as a health intervention were found. One study on the use of the circus as an intervention in schools was identified. It demonstrated an increase in self-esteem in the children who took part. One study on the use of the circus in a First Nations community was found; it contained nonspecific, qualitative findings. The other articles identified were merely descriptions of social circuses. One website was identified on the use of the social circus to help youth who had been treated in a hospital setting for major psychiatric disorders to re-enter the community. The team in the pediatric psychiatry department at Centre Hospitalier Universitaire Sainte-Justine, the children’s hospital in Montreal, Que, was contacted; they were leading this project, called Espace Transition. The unpublished preliminary findings of its pilot project demonstrate substantial improvements in overall patient

  4. The use of scale models in impact testing

    International Nuclear Information System (INIS)

    Donelan, P.J.; Dowling, A.R.

    1985-01-01

    Theoretical analysis, component testing and model flask testing are employed to investigate the validity of scale models for demonstrating the behaviour of Magnox flasks under impact conditions. Model testing is shown to be a powerful and convenient tool provided adequate care is taken with detail design and manufacture of models and with experimental control. (author)

  5. A person fit test for IRT models for polytomous items

    NARCIS (Netherlands)

    Glas, Cornelis A.W.; Dagohoy, A.V.

    2007-01-01

    A person fit test based on the Lagrange multiplier test is presented for three item response theory models for polytomous items: the generalized partial credit model, the sequential model, and the graded response model. The test can also be used in the framework of multidimensional ability

  6. Gestion durable du paysage

    Directory of Open Access Journals (Sweden)

    Jean-David Gerber

    2009-03-01

    Full Text Available Le paysage est de plus en plus perçu comme une ressource. À ce titre, il est nécessaire de trouver des instruments juridiques, politiques ou économiques susceptibles de gérer cette « ressource-paysage » sur le long terme. Le gouvernement suisse a introduit récemment l’instrument des parcs naturels régionaux, organisés selon le modèle français, dans sa législation de protection de la nature et du paysage. Une mise en regard des nouveaux parcs avec des structures de gestion beaucoup plus anciennes, les bourgeoisies et les corporations, permet de mettre en évidence les forces et les faiblesses de chacun de ces instruments dans leur contribution à résoudre les rivalités d’usage entre acteurs utilisant ou influençant la ressource paysage. Cette comparaison permet de formuler des recommandations pratiques concernant la gestion de cette ressource.The landscape is increasingly perceived as a resource. For this reason, it is necessary to find legal, political and economic instruments that will succeed in managing this “resource landscape” in the long term. The Swiss government recently introduced the instrument of regional nature parks into the legislation governing nature and landscape preservation; the proposed parks are organized on the basis of the French model. The examination of the new parks from the perspective of much older management structures, i.e. the civic municipalities (bourgeoisies and corporations, makes it possible to demonstrate the strengths and weaknesses of each of these instruments in their contribution to the resolution of use rivalries between actors who use or influence the resource landscape. This comparison also enables the formulation of practical recommendations regarding the management of this resource.

  7. Comparative study of {beta} decays and of the model of the layers for the nucleus with odd a; Etude comparee des desintegrations {beta} et du modele des couches pour les noyaux de a impair

    Energy Technology Data Exchange (ETDEWEB)

    Trocheris, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1953-07-01

    The systematic comparison of {beta} decays of the cores of number of odd mass with the predictions of the modal of Mrs. Mayer on spins and parities, has already been made by several authors. It is taken in the present work with more recent experimental data and with a method of classification of the {beta} transitions. A simultaneous comparison to the experience of the model of the layers and the theory of the {beta} transitions can serve to verify one and the other too. In the present work, it appeared more fruitful to try to verify the model of the layers with the help of the very established theory of the {beta} transitions. One will look to verify and perfect the models of the layers for transitions between fundamental states or isomers of the cores. (M.B.) [French] La comparaison systematique des desintegrations {beta} des noyaux de nombre de masse impair avec les predictions du modale de Mme MAYER sur les spins et les parites, a deja ete faite par plusieurs auteurs. Elle est reprise dans le present travail avec des donnees experimentales plus recentes et avec une methode de classification des transitions {beta}. Une comparaison simultanee a l'experience du modele des couches et de la theorie des transitions {beta} peut, a priori, servir a verifier egalement l'un et l'autre. Dans le present travail, il a paru plus fructueux de chercher a verifier le modele des couches a l'aide de la theorie bien etablie des transitions {beta}. On cherchera de verifier et de perfectionner le modele des couches pour les transitions entre etats fondamentaux ou isomeres des noyaux. (M.B.)

  8. les cahiers du cread

    African Journals Online (AJOL)

    Our Journal “les cahiers du cread” is a quarterly economic review publishing original findings of empirical research and theoretical debates on fields pertaining to our mission coverage (Macro Economics, Industrial Economics and Firms, Human Development & Social Economics, Agriculture & Environment). Other websites ...

  9. Accelerated testing statistical models, test plans, and data analysis

    CERN Document Server

    Nelson, Wayne B

    2009-01-01

    The Wiley-Interscience Paperback Series consists of selected books that have been made more accessible to consumers in an effort to increase global appeal and general circulation. With these new unabridged softcover volumes, Wiley hopes to extend the lives of these works by making them available to future generations of statisticians, mathematicians, and scientists. "". . . a goldmine of knowledge on accelerated life testing principles and practices . . . one of the very few capable of advancing the science of reliability. It definitely belongs in every bookshelf on engineering.""-Dev G.

  10. Standard Model theory calculations and experimental tests

    International Nuclear Information System (INIS)

    Cacciari, M.; Hamel de Monchenault, G.

    2015-01-01

    To present knowledge, all the physics at the Large Hadron Collider (LHC) can be described in the framework of the Standard Model (SM) of particle physics. Indeed the newly discovered Higgs boson with a mass close to 125 GeV seems to confirm the predictions of the SM. Thus, besides looking for direct manifestations of the physics beyond the SM, one of the primary missions of the LHC is to perform ever more stringent tests of the SM. This requires not only improved theoretical developments to produce testable predictions and provide experiments with reliable event generators, but also sophisticated analyses techniques to overcome the formidable experimental environment of the LHC and perform precision measurements. In the first section, we describe the state of the art of the theoretical tools and event generators that are used to provide predictions for the production cross sections of the processes of interest. In section 2, inclusive cross section measurements with jets, leptons and vector bosons are presented. Examples of differential cross sections, charge asymmetries and the study of lepton pairs are proposed in section 3. Finally, in section 4, we report studies on the multiple production of gauge bosons and constraints on anomalous gauge couplings

  11. Methods and models for the construction of weakly parallel tests

    NARCIS (Netherlands)

    Adema, J.J.; Adema, Jos J.

    1990-01-01

    Methods are proposed for the construction of weakly parallel tests, that is, tests with the same test information function. A mathematical programing model for constructing tests with a prespecified test information function and a heuristic for assigning items to tests such that their information

  12. Numerical modeling of transferred arc melting bath heating; Modelisation numerique du chauffage de bains par arc transfere

    Energy Technology Data Exchange (ETDEWEB)

    Bouvier, A. [Electricite de France, 77 - Moret sur Loing (France). Direction des Etudes et Recherches; Trenty, L.; Guillot, J.B. [Ecole Centrale de Paris, Laboratoire EM2C. CNRS, 92 - Chatenay-Malabry (France); Delalondre, C. [Electricite de France (EDF), 78 - Chatou (France). Direction des Etudes et Recherches

    1997-12-31

    This paper presents the modeling of a transferred electric arc inside a bath of melted metal. After a recall of the context of the study, the problem of the modeling, which involves magnetohydrodynamic coupling inside the arc and the bath, is described. The equations that govern the phenomena inside the arc and the bath are recalled and the approach used for the modeling of the anode region of the arc is explained using a 1-D sub-model. The conditions of connection between arc and bath calculations are explained and calculation results obtained with a 200 kW laboratory furnace geometry are presented. (J.S.) 8 refs.

  13. In vitro effects of piracetam on the radiosensitivity of hypoxic cells (adaptation of MTT assay to hypoxic conditions); Effets in vitro du piracetam sur la radiosensibilite des cellules hypoxiques (adapatation du test au MTT aux conditions d`hypoxie)

    Energy Technology Data Exchange (ETDEWEB)

    Gheuens, E.E.O.; Bruijn, E.A. de; Van der Heyden, S.; Van Oosterom, A.T. [Universitaire Instelling Antwerpen, Antwerp (Belgium); Lagarde, P. [Universitaire Instelling Antwerpen, Antwerp (Belgium)]|[Institut Bergonie, 33 - Bordeaux (France); Pooter, C.M.J. de [Universitaire Instelling Antwerpen, Antwerp (Belgium)]|[Hopital de Middelheim, Anvers (Belgium); Chomy, F. [Institut Bergonie, 33 - Bordeaux (France)

    1995-12-31

    This paper describes the adaptation of the MTT assay to hypoxic conditions in order to test the in vitro effect of piracetam on hypoxic cells and particularly on the radiosensitivity of hypoxic cells since this drug has shown clinical effect on acute and chronic hypoxia. The V79 cell line was selected by reference to preliminary hypoxic experiments using clonogenic assay and euoxic experiments using clonogenic and MTT assays. Cell growth and survival in our hypoxic conditions were assessed using MTT assay with an enclosure and special 48-well plates both made of glass. Growth curves on glass plates after 1-hour exposure to nitrogen versus air were comparable, so there is no bias effect due to gas composition. Survival curves using MTT versus reference clonogenic assay were comparable after radiation exposure in eu- and hypoxic conditions, and confirm the validity of our original technique for creating hypoxia. The Oxygen Enhancement Ratio was of about 3 for 1-hour hypoxic exposure. Piracetam gave no cytotoxic effect up to 10 mM of piracetam. Growth curves after continuous drug exposure and 1-hour euoxic versus hypoxic exposure gave no cytotoxic effect up to 10 mM of piracetam. Survival curves after continuous drug exposure to 10 mM of piracetam gave no significant effect on the radiosensitivity of hypoxic V79 cells using MTT or clonogenic assay. (author). 32 refs., 6 figs.

  14. Comparaison du filtre adaptatif RIF et du filtre a base de reseau de ...

    African Journals Online (AJOL)

    Comparaison du filtre adaptatif RIF et du filtre a base de reseau de neurones pour le filtrage du courant de reference pour la commande du filtre actif parallele. C Benachaiba, A Bassou, B Mazari ...

  15. Putting hydrological modelling practice to the test

    NARCIS (Netherlands)

    Melsen, Lieke Anna

    2017-01-01

    Six steps can be distinguished in the process of hydrological modelling: the perceptual model (deciding on the processes), the conceptual model (deciding on the equations), the procedural model (get the code to run on a computer), calibration (identify the parameters), evaluation (confronting

  16. Thermohydraulic tests in nuclear fuel model

    International Nuclear Information System (INIS)

    Ladeira, L.C.D.; Navarro, M.A.

    1984-01-01

    The main experimental works performed in the Thermohydraulics Laboratory of the NUCLEBRAS Nuclear Technology Development Center, in the field of thermofluodynamics are briefly described. These works include the performing of steady-state flow tests in single tube test sections, and the design and construction of a rod bundle test section, which will be also used for those kind of testes. Mention is made of the works to be performed in the near future, related to steady-state and transient flow tests. (Author) [pt

  17. Transcriptomic effects of depleted uranium on acetylcholine and cholesterol metabolisms in Alzheimer's disease model; Effets transcriptomiques de l'uranium appauvri sur les metabolismes de l'acetylcholine et du cholesterol chez un modele de maladie d'Alzheimer

    Energy Technology Data Exchange (ETDEWEB)

    Lestaevel, Ph.; Bensoussan, H.; Racine, R.; Airault, F.; Gourmelon, P.; Souidi, M. [Direction de la radioprotection de l' Homme, service de radiobiologie et d' epidemiologie, laboratoire de radiotoxicologie experimentale, institut de radioprotection et de surete nucleaire, BP no 17, 92262 Fontenay-aux-Roses cedex (France)

    2011-02-15

    Some heavy metals, or aluminium, could participate in the development of Alzheimer disease (AD). Depleted uranium (DU), another heavy metal, modulates the cholinergic system and the cholesterol metabolism in the brain of rats, but without neurological disorders. The aim of this study was to determine what happens in organisms exposed to DU that will/are developing the AD. This study was thus performed on a transgenic mouse model for human amyloid precursor protein (APP), the Tg2576 strain. The possible effects of DU through drinking water (20 mg/L) over an 8-month period were analyzed on acetylcholine and cholesterol metabolisms at gene level in the cerebral cortex. The mRNA levels of choline acetyl transferase (ChAT) vesicular acetylcholine transporter (VAChT) and ATP-binding cassette transporter A1 (ABC A1) decreased in control Tg2576 mice in comparison with wild-type mice (respectively -89%, -86% and -44%, p < 0.05). Chronic exposure of Tg2576 mice to DU increased mRNA levels of ChAT (+189%, p < 0.05), VAChT (+120%, p < 0.05) and ABC A1 (+52%, p < 0.05) compared to control Tg2576 mice. Overall, these modifications of acetylcholine and cholesterol metabolisms did not lead to increased disturbances that are specific of AD, suggesting that chronic DU exposure did not worsen the pathology in this experimental model. (authors)

  18. A test for the parameters of multiple linear regression models ...

    African Journals Online (AJOL)

    A test for the parameters of multiple linear regression models is developed for conducting tests simultaneously on all the parameters of multiple linear regression models. The test is robust relative to the assumptions of homogeneity of variances and absence of serial correlation of the classical F-test. Under certain null and ...

  19. Rate-control algorithms testing by using video source model

    DEFF Research Database (Denmark)

    Belyaev, Evgeny; Turlikov, Andrey; Ukhanova, Anna

    2008-01-01

    In this paper the method of rate control algorithms testing by the use of video source model is suggested. The proposed method allows to significantly improve algorithms testing over the big test set.......In this paper the method of rate control algorithms testing by the use of video source model is suggested. The proposed method allows to significantly improve algorithms testing over the big test set....

  20. Modelling and experimental study of the behavior of radon and radon decay products in an enclosure. Application to houses; Modelisation et etude experimentale du comportement du radon et de ses descendants dans une enceinte confinee. Application a une habitation

    Energy Technology Data Exchange (ETDEWEB)

    Gouronnec, A M

    1995-02-03

    Since the eighties, more and more studies were performed about radon and its decay products in houses with one of the aim being the estimation of the dose received by their inhabitants. Then, the principal objective of this work is to describe the behaviour of radon and its decay products within a dwelling. In the first part to the report, a few definitions are given and data from literature give an idea of indoor radon and radon decay products activities and/or size distribution. Aspects of dosimetry are presented too. In the second part of the work, a mathematical model, called `PRADDO` of Physic of Radon and radon Decay products in Domestic environment is developed on the basis of the classical model written by Jacobi in 1972. On the one hand, it has to predict radon decay products activities in systems consisting in one or more enclosure(s), from radon activity and from ambient aerosol concentration and size distribution. On the other hand, one part of the model is assigned to study the influence of the entry model parameters variation on the calculated quantities. Then, in the third part of the work, two experimental studies are realised in order to compare measurements to modelization. The first experimentation is a laboratory work, made on the test bench ICARE from IPSN, and the second one consists in describing the basement of an occupied house from Brittany. In the two cases, the comparison between experiments and modelling shows a good agreement if particles are present in the air, but any conclusion is made when is no aerosol in the enclosure. (author). 158 refs., 81 figs., 42 tabs.

  1. Application of the concrete aging model to the case of cracked materials and to the coupling with the mechanical properties; Application du modele de degradation du beton au cas des milieux fissures et au couplage avec la mecanique

    Energy Technology Data Exchange (ETDEWEB)

    Torrenti, J.M.; Adenot, F.; Tognazzi, C. [CEA/Saclay, 91 - Gif-sur-Yvette (France); Tognazzi, C. [Toulouse Univ., 31 (France). LMDC; Danese, S. [Ecole Nationale Superieure des Arts et Industries de Strasbourg, 67 - Strasbourg (France); Poyet, S. [Ecole Nationale Superieure de Cachan, 94 (France)

    1998-07-01

    Predicting the long-term behavior of concrete used in radioactive waste disposal requires the knowledge of the effects of constantly renewed water on its chemistry and its coupling with the mechanical properties. In contact with water, concrete undergoes chemical degradation. This degradation influences the mechanical performance of the material as well as cracks could interfere with the chemical degradation. This paper shows how these problems can be treated using the Ca{sup ++} concentration in pore solution as the state variable that conducts the evolution of chemical, physical and mechanical properties. Some comparisons with experimental results are shown. Finally, the problem of the numerical simulation of accelerated tests of cracked samples is discussed. (authors)

  2. Mediterranean climate modelling: variability and climate change scenarios; Modelisation climatique du Bassin mediterraneen: variabilite et scenarios de changement climatique

    Energy Technology Data Exchange (ETDEWEB)

    Somot, S

    2005-12-15

    Air-sea fluxes, open-sea deep convection and cyclo-genesis are studied in the Mediterranean with the development of a regional coupled model (AORCM). It accurately simulates these processes and their climate variabilities are quantified and studied. The regional coupling shows a significant impact on the number of winter intense cyclo-genesis as well as on associated air-sea fluxes and precipitation. A lower inter-annual variability than in non-coupled models is simulated for fluxes and deep convection. The feedbacks driving this variability are understood. The climate change response is then analysed for the 21. century with the non-coupled models: cyclo-genesis decreases, associated precipitation increases in spring and autumn and decreases in summer. Moreover, a warming and salting of the Mediterranean as well as a strong weakening of its thermohaline circulation occur. This study also concludes with the necessity of using AORCMs to assess climate change impacts on the Mediterranean. (author)

  3. Le ministre du Commerce international du Canada rencontre des ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    17 juil. 2017 ... La promotion de l'entrepreneuriat, la façon dont le commerce peut profiter aux femmes et à leur famille, et la création d'emplois pour les plus vulnérables étaient au coeur de la discussion en table ronde du ministre du Commerce international du Canada, l'honorable François-Philippe Champagne, et des ...

  4. Methods and models for the construction of weakly parallel tests

    NARCIS (Netherlands)

    Adema, J.J.; Adema, Jos J.

    1992-01-01

    Several methods are proposed for the construction of weakly parallel tests [i.e., tests with the same test information function (TIF)]. A mathematical programming model that constructs tests containing a prespecified TIF and a heuristic that assigns items to tests with information functions that are

  5. Optimization models for flight test scheduling

    Science.gov (United States)

    Holian, Derreck

    As threats around the world increase with nations developing new generations of warfare technology, the Unites States is keen on maintaining its position on top of the defense technology curve. This in return indicates that the U.S. military/government must research, develop, procure, and sustain new systems in the defense sector to safeguard this position. Currently, the Lockheed Martin F-35 Joint Strike Fighter (JSF) Lightning II is being developed, tested, and deployed to the U.S. military at Low Rate Initial Production (LRIP). The simultaneous act of testing and deployment is due to the contracted procurement process intended to provide a rapid Initial Operating Capability (IOC) release of the 5th Generation fighter. For this reason, many factors go into the determination of what is to be tested, in what order, and at which time due to the military requirements. A certain system or envelope of the aircraft must be assessed prior to releasing that capability into service. The objective of this praxis is to aide in the determination of what testing can be achieved on an aircraft at a point in time. Furthermore, it will define the optimum allocation of test points to aircraft and determine a prioritization of restrictions to be mitigated so that the test program can be best supported. The system described in this praxis has been deployed across the F-35 test program and testing sites. It has discovered hundreds of available test points for an aircraft to fly when it was thought none existed thus preventing an aircraft from being grounded. Additionally, it has saved hundreds of labor hours and greatly reduced the occurrence of test point reflight. Due to the proprietary nature of the JSF program, details regarding the actual test points, test plans, and all other program specific information have not been presented. Generic, representative data is used for example and proof-of-concept purposes. Apart from the data correlation algorithms, the optimization associated

  6. Test Driven Development of Scientific Models

    Science.gov (United States)

    Clune, Thomas L.

    2014-01-01

    Test-Driven Development (TDD), a software development process that promises many advantages for developer productivity and software reliability, has become widely accepted among professional software engineers. As the name suggests, TDD practitioners alternate between writing short automated tests and producing code that passes those tests. Although this overly simplified description will undoubtedly sound prohibitively burdensome to many uninitiated developers, the advent of powerful unit-testing frameworks greatly reduces the effort required to produce and routinely execute suites of tests. By testimony, many developers find TDD to be addicting after only a few days of exposure, and find it unthinkable to return to previous practices.After a brief overview of the TDD process and my experience in applying the methodology for development activities at Goddard, I will delve more deeply into some of the challenges that are posed by numerical and scientific software as well as tools and implementation approaches that should address those challenges.

  7. Portage vaginal du streptocoque du groupe B chez la femme ...

    African Journals Online (AJOL)

    Introduction: le streptocoque du groupe B est le principal agent impliqué dans les infections materno-fœtales, les septicémies et les méningites du nouveau-né à terme. L'objectif est de déterminer le taux de portage maternel du streptocoque du groupe B (SGB) à terme. Méthodes: un prélèvement vaginal a été réalisé de ...

  8. Aux origines du monde

    CERN Multimedia

    2004-01-01

    "C'est l'histoire d'une aventure humaine, scientifique, international qui a vu le jour il y a cinquante ans, aux confins de la Suisse et du département de l'Ain. Le plus grand laboratoire de physique des particules du monde, le Cern, a été fondé en 1954. Les festivités organisées à l occasion de cet anniversaire connaîtront leur point d'orgue le 16 octobre prochain, avec portes-ouvertes, accueil de personallités et inauguration d'un monumnet spécifique, le Globe de l'innovation" (2 pages)

  9. CHOEUR DU CERN

    CERN Multimedia

    CHOEUR DU CERN

    2010-01-01

    Les répétitions du chœur du CERN reprendront le mercredi 15 septembre à 20.00 heures à l’amphithéâtre principal – bâtiment 500. Au programme la préparation de notre concert de Noël avec la Missa Brevis, KV115, de Léopold Mozart et de la musique de Noël d’Europe. Les personnes qui aiment chanter, notamment des sopranes et des ténors, sont les bienvenues. Pour tout contact s’adresser à : Baudouin Bleus - (tél.CERN 767 82 44) -(baudouin.bleus@cern.ch) ou Martin Gatehouse ( martin.gatehouse@wanadoo.fr) ou Jean-Paul Diss (jean-pauldiss@wanadoo.fr).  

  10. An alternative for cost-effective remediation of depleted uranium (DU) at certain environmental restoration sites

    International Nuclear Information System (INIS)

    Miller, M.; Galloway, B.; VanDerpoel, G.; Johnson, E.; Copland, J.; Salazar, M.

    2000-01-01

    Numerous sites in the United States and around the world are contaminated with depleted uranium (DU) in various forms. A prevalent form is fragmented DU originating from various scientific tests involving high explosives and DU during weapon development programs, at firing practice ranges, or war theaters where DU was used in armor-piercing projectiles. The contamination at these sites is typically very heterogeneous, with discreet, visually identifiable DU fragments mixed with native soil. That is, the bulk-averaged DU activity is quite low, while specific DU fragments, which are distinct from the soil matrix, have much higher specific activity. DU is best known as a dark, black metal that is nearly twice as dense as lead, but DU in the environment readily weathers to a distinctive bright yellow color that is readily visible. While the specific activity of DU is relatively low and presents only a minor radiological hazard, the fact that it is radioactive and visually identifiable makes it desirable to remove the DU contamination from the environment

  11. An alternative for cost-effective remediation of depleted uranium (DU) at certain environmental restoration sites

    Energy Technology Data Exchange (ETDEWEB)

    Miller, M.; Galloway, B.; VanDerpoel, G.; Johnson, E.; Copland, J.; Salazar, M.

    2000-02-01

    Numerous sites in the United States and around the world are contaminated with depleted uranium (DU) in various forms. A prevalent form is fragmented DU originating from various scientific tests involving high explosives and DU during weapon development programs, at firing practice ranges, or war theaters where DU was used in armor-piercing projectiles. The contamination at these sites is typically very heterogeneous, with discreet, visually identifiable DU fragments mixed with native soil. That is, the bulk-averaged DU activity is quite low, while specific DU fragments, which are distinct from the soil matrix, have much higher specific activity. DU is best known as a dark, black metal that is nearly twice as dense as lead, but DU in the environment readily weathers to a distinctive bright yellow color that is readily visible. While the specific activity of DU is relatively low and presents only a minor radiological hazard, the fact that it is radioactive and visually identifiable makes it desirable to remove the DU contamination from the environment.

  12. Test Driven Development of Scientific Models

    Science.gov (United States)

    Clune, Thomas L.

    2012-01-01

    Test-Driven Development (TDD) is a software development process that promises many advantages for developer productivity and has become widely accepted among professional software engineers. As the name suggests, TDD practitioners alternate between writing short automated tests and producing code that passes those tests. Although this overly simplified description will undoubtedly sound prohibitively burdensome to many uninitiated developers, the advent of powerful unit-testing frameworks greatly reduces the effort required to produce and routinely execute suites of tests. By testimony, many developers find TDD to be addicting after only a few days of exposure, and find it unthinkable to return to previous practices. Of course, scientific/technical software differs from other software categories in a number of important respects, but I nonetheless believe that TDD is quite applicable to the development of such software and has the potential to significantly improve programmer productivity and code quality within the scientific community. After a detailed introduction to TDD, I will present the experience within the Software Systems Support Office (SSSO) in applying the technique to various scientific applications. This discussion will emphasize the various direct and indirect benefits as well as some of the difficulties and limitations of the methodology. I will conclude with a brief description of pFUnit, a unit testing framework I co-developed to support test-driven development of parallel Fortran applications.

  13. Hepatiques du Surinam

    NARCIS (Netherlands)

    Jovet-Ast, S.

    1957-01-01

    Il n’existe pas, actuellement, de catalogue des Hépatiques du Surinam. Les Hépatiques de ce pays restent très peu connues. Cependant, certaines ont attiré l’attention des Bryologues et ont été citées dans quelques ouvrages anciens ou récents. Je ne ferai pas ici une révision complète de ces

  14. (l.) Medik du Maroc

    African Journals Online (AJOL)

    PR BOKO

    Résumé. Dipcadi serotinum (L.) Medik, est une plante de la famille des Hyacinthaceae, elle est largement utilisée comme réchauffant et aussi pour combattre la jaunisse. Cette plante trouve une large utilisation par la population de la région côtière du Maroc. À notre connaissance l'huile essentielle de cette espèce n'a ...

  15. A damage model of Zr {alpha} under cyclic loading at 200 degree Celsius; Modelisation de l`endommagement du Zr {alpha} sous chargement cyclique a 200 deg C

    Energy Technology Data Exchange (ETDEWEB)

    Vogel, C.; Drubay, B. [CEA Centre d`Etudes de Saclay, 91 - Gif-sur-Yvette (France). Dept. de Mecanique et de Technologie; Cailletaud, G. [Ecole Nationale Superieure des Mines, 75 - Paris (France); Mottot, M. [CEA Centre d`Etudes de Saclay, 91 - Gif-sur-Yvette (France). Direction des Technologies Avancees

    1994-12-31

    A damage model for anticipating zirconium {alpha} test-piece rupture under cyclic solicitations at 200 degree Celsius is presented. The article is divided into three parts : an experimental approach, the damage model presentation and the application of this model. (O.L.). 10 refs., 7 figs., 4 tabs.

  16. La mesure du danger

    CERN Document Server

    Manceron, Vanessa; Revet, Sandrine

    2014-01-01

    La mesure du danger permet d’explorer des dangers de nature aussi diverse que la délinquance, la pollution, l’écueil maritime, la maladie ou l’attaque sorcellaire, l’extinction d’espèces animales ou végétales, voire de la Planète tout entière. Au croisement de la sociologie, de l’anthropologie et de l’histoire, les différents articles analysent les pratiques concrètes de mesure pour tenter de comprendre ce qui se produit au cours de l’opération d’évaluation du danger sans préjuger de la nature de celui-ci. L’anthropologie a contribué à la réflexion sur l’infortune en s’intéressant aux temporalités de l’après : maladies, catastrophes, pandémies, etc. et en cherchant à rendre compte de l’expérience des victimes, de leur vie ordinaire bouleversée, de la recomposition du quotidien. Elle s’intéresse aussi aux autres types de mesures, les savoirs incorporés, qui reposent sur l’odorat, la vue ou le toucher et ceux qui ressortent d’une épistémologie « non ...

  17. Testing the generalized partial credit model

    OpenAIRE

    Glas, Cornelis A.W.

    1996-01-01

    The partial credit model (PCM) (G.N. Masters, 1982) can be viewed as a generalization of the Rasch model for dichotomous items to the case of polytomous items. In many cases, the PCM is too restrictive to fit the data. Several generalizations of the PCM have been proposed. In this paper, a generalization of the PCM (GPCM), a further generalization of the one-parameter logistic model, is discussed. The model is defined and the conditional maximum likelihood procedure for the method is describe...

  18. Testing the compounding structure of the CP-INARCH model

    OpenAIRE

    Weiß, Christian H.; Gonçalves, Esmeralda; Lopes, Nazaré Mendes

    2017-01-01

    A statistical test to distinguish between a Poisson INARCH model and a Compound Poisson INARCH model is proposed, based on the form of the probability generating function of the compounding distribution of the conditional law of the model. For first-order autoregression, the normality of the test statistics’ asymptotic distribution is established, either in the case where the model parameters are specified, or when such parameters are consistently estimated. As the test statistics’ law involv...

  19. Global sensitivity analysis of thermomechanical models in modelling of welding; Analyse de sensibilite globale de modeles thermomecanique de simulation numerique du soudage

    Energy Technology Data Exchange (ETDEWEB)

    Petelet, M

    2008-07-01

    Current approach of most welding modellers is to content themselves with available material data, and to chose a mechanical model that seems to be appropriate. Among inputs, those controlling the material properties are one of the key problems of welding simulation: material data are never characterized over a sufficiently wide temperature range. This way to proceed neglect the influence of the uncertainty of input data on the result given by the computer code. In this case, how to assess the credibility of prediction? This thesis represents a step in the direction of implementing an innovative approach in welding simulation in order to bring answers to this question, with an illustration on some concretes welding cases.The global sensitivity analysis is chosen to determine which material properties are the most sensitive in a numerical welding simulation and in which range of temperature. Using this methodology require some developments to sample and explore the input space covering welding of different steel materials. Finally, input data have been divided in two groups according to their influence on the output of the model (residual stress or distortion). In this work, complete methodology of the global sensitivity analysis has been successfully applied to welding simulation and lead to reduce the input space to the only important variables. Sensitivity analysis has provided answers to what can be considered as one of the probable frequently asked questions regarding welding simulation: for a given material which properties must be measured with a good accuracy and which ones can be simply extrapolated or taken from a similar material? (author)

  20. Global sensitivity analysis of thermo-mechanical models in numerical weld modelling; Analyse de sensibilite globale de modeles thermomecaniques de simulation numerique du soudage

    Energy Technology Data Exchange (ETDEWEB)

    Petelet, M

    2007-10-15

    Current approach of most welding modellers is to content themselves with available material data, and to chose a mechanical model that seems to be appropriate. Among inputs, those controlling the material properties are one of the key problems of welding simulation: material data are never characterized over a sufficiently wide temperature range {exclamation_point} This way to proceed neglect the influence of the uncertainty of input data on the result given by the computer code. In this case, how to assess the credibility of prediction? This thesis represents a step in the direction of implementing an innovative approach in welding simulation in order to bring answers to this question, with an illustration on some concretes welding cases. The global sensitivity analysis is chosen to determine which material properties are the most sensitive in a numerical welding simulation and in which range of temperature. Using this methodology require some developments to sample and explore the input space covering welding of different steel materials. Finally, input data have been divided in two groups according to their influence on the output of the model (residual stress or distortion). In this work, complete methodology of the global sensitivity analysis has been successfully applied to welding simulation and lead to reduce the input space to the only important variables. Sensitivity analysis has provided answers to what can be considered as one of the probable frequently asked questions regarding welding simulation: for a given material which properties must be measured with a good accuracy and which ones can be simply extrapolated or taken from a similar material? (author)

  1. Model Based Analysis and Test Generation for Flight Software

    Science.gov (United States)

    Pasareanu, Corina S.; Schumann, Johann M.; Mehlitz, Peter C.; Lowry, Mike R.; Karsai, Gabor; Nine, Harmon; Neema, Sandeep

    2009-01-01

    We describe a framework for model-based analysis and test case generation in the context of a heterogeneous model-based development paradigm that uses and combines Math- Works and UML 2.0 models and the associated code generation tools. This paradigm poses novel challenges to analysis and test case generation that, to the best of our knowledge, have not been addressed before. The framework is based on a common intermediate representation for different modeling formalisms and leverages and extends model checking and symbolic execution tools for model analysis and test case generation, respectively. We discuss the application of our framework to software models for a NASA flight mission.

  2. Testing the generalized partial credit model

    NARCIS (Netherlands)

    Glas, Cornelis A.W.

    1996-01-01

    The partial credit model (PCM) (G.N. Masters, 1982) can be viewed as a generalization of the Rasch model for dichotomous items to the case of polytomous items. In many cases, the PCM is too restrictive to fit the data. Several generalizations of the PCM have been proposed. In this paper, a

  3. Presentation of the CPR ISMIR (Insulators: IRradiation Modelling); Presentation du CPR ISMIR (ISolants: modelisation de l'IRradiation)

    Energy Technology Data Exchange (ETDEWEB)

    Lozes, G. [CEA Saclay, Dir. de l' Energie Nucleaire (DEN/DSOE), 91 - Gif sur Yvette (France)

    2007-07-01

    The CPR ISMIR is a CEA-CNRS program on the behaviour of materials submitted to irradiation; it has been begun to support the applied current research programs on the aging of nuclear fuels, the storage and incineration matrices and the future reactors. Its aim is to contribute to scientifically set up the methods for anticipating the behaviour of ceramic materials under irradiation in using the important development of calculation means. Thus have been developed the basic knowledge and the interactions physics and calculation models at pertinent scales have been elaborated. (O.M.)

  4. A test of inflated zeros for Poisson regression models.

    Science.gov (United States)

    He, Hua; Zhang, Hui; Ye, Peng; Tang, Wan

    2017-01-01

    Excessive zeros are common in practice and may cause overdispersion and invalidate inference when fitting Poisson regression models. There is a large body of literature on zero-inflated Poisson models. However, methods for testing whether there are excessive zeros are less well developed. The Vuong test comparing a Poisson and a zero-inflated Poisson model is commonly applied in practice. However, the type I error of the test often deviates seriously from the nominal level, rendering serious doubts on the validity of the test in such applications. In this paper, we develop a new approach for testing inflated zeros under the Poisson model. Unlike the Vuong test for inflated zeros, our method does not require a zero-inflated Poisson model to perform the test. Simulation studies show that when compared with the Vuong test our approach not only better at controlling type I error rate, but also yield more power.

  5. Un probleme d’identification. Correction du modeles analytique en utilisat des données expérimentales

    Directory of Open Access Journals (Sweden)

    Gabriela Covatariu

    2009-01-01

    Full Text Available La procédure de correction d’un modele analytique adopté pour une structure de construction est précédée d’une comparaison entre le set des données expérimentales et celui des données analytiques, pour une vérification préliminaire concernant la correspondance raisonnable entre ces données. Pour l’identification dynamique des parametres ont été élaborées diverses méthodes de correction des matrices de rigidité et de l’amortissement qui ont a leur base la méthode des moindres carrés dans le domaine des fréquences. L’algorithme proposé a comme résultat la correction de la matrice de rigidité d’un modele de calcul en utilisant comme données d’entrée seulement celles enregistrées pendant les essais expérimentaux.

  6. 2-D Model Test Study of the Suape Breakwater, Brazil

    DEFF Research Database (Denmark)

    Andersen, Thomas Lykke; Burcharth, Hans F.; Sopavicius, A.

    This report deals with a two-dimensional model test study of the extension of the breakwater in Suape, Brazil. One cross-section was tested for stability and overtopping in various sea conditions. The length scale used for the model tests was 1:35. Unless otherwise specified all values given...

  7. The Economical Application of Non-Destructive Testing to Reactor Components, Especially Jacket Tubing; Avantages Economiques du Controle Non Destructif des Pieces de Reacteurs, Notamment des Tubes de Gainage; Ehkonomicheskoe primenenie nedestruktivnykh ispytanij dlya reaktornykh komponentov, v chastnosti obolochechnykh trub; Aplicacion en Condiciones Economicas de Ensayos No Destructivos a las Piezas de los Reactores, en Especial a los Tubos de Revestimiento

    Energy Technology Data Exchange (ETDEWEB)

    Renken, C. J. [Metallurgy Division Argonne National Laboratory Argonne, IL (United States)

    1965-10-15

    electro-magnetic method for technical as well as economic reasons. The optimum area of application of these two methods is explained as well as the large area of overlap where results produced by well- designed and properly operated equipment of both types are essentially equivalent. Spurious defect indications contribute directly to increased component costs, so an evaluation of these effects for both the ultrasonic and the electromagnetic test methods is included for several commonly encountered sources of spurious defect signals. The experience in the application of these methods at Argonne National Laboratory on relatively large quantities of tubing from various sources are recounted from the standpoint of the lowest possible inspection cost per unit length of tubing. This section also summarizes experience gained at Argonne with the newer pulsed electromagnetic test methods. The critical but generally unappreciated role of tube diameter and wall thickness on tube inspection cost is discussed. Since the question of economical inspection is closely related to allowable defect levels, defect levels and standards in use at Argonne are covered. Finally, the practical and theoretical barriers to reduced component inspection costs are enumerated and a projection of what possible reductions in cost might be attainable in the future with the ultrasonic and electromagnetic test methods is attempted. (author) [French] Le reacteur ideal aurait entre autres caracteristiques celle de ne pas exiger de controles non destructifs. Cet ideal, comme tant d'autres, ne sera probablement jamais atteint. Dans l'etude de tout reacteur pour lequel le prix de revient constitue un facteur important, il faudrait envisager la question de savoir si les pieces de ce reacteur pourront etre essayees de facon economique en meme temps que l'on examine les possibilites de fabrication. Cette partie du memoire contient quelques considerations a ce propos ainsi qu'un expose de l'importance des essais non

  8. Testing constancy of unconditional variance in volatility models by misspecification and specification tests

    DEFF Research Database (Denmark)

    Silvennoinen, Annastiina; Terasvirta, Timo

    The topic of this paper is testing the hypothesis of constant unconditional variance in GARCH models against the alternative that the unconditional variance changes deterministically over time. Tests of this hypothesis have previously been performed as misspecification tests after fitting a GARCH...... models. An application to exchange rate returns is included....

  9. Underwater behaviour of bitumen coated radioactive wastes: experimental validation of the Colonbo degradation model; Comportement sous eau des dechets radioactifs bitumes: validation experimentale du modele de degradation Colonbo

    Energy Technology Data Exchange (ETDEWEB)

    Gwinner, B

    2004-03-01

    the morphology of the permeable layer of partially leached bituminized waste samples is studied. The porosity and the pore distribution in the permeable layer are quantified according to a semi-automatic method based on the analysis of Environmental Scanning Electron Microscope images. The obtained experimental porosity profiles are compared successfully to those resulting from simulations performed with the COLONBO model. The effective diffusion coefficients of water and salts in the permeable layer of leached bituminized waste samples are then directly measured by through diffusion experiments. In the experiments, the flow of radioactive tracers (water and salts) through thin membranes of partially leached bituminized waste is followed in time. Due to the evolution of the bitumen specimen during the tests (continuous leaching), a specific method of analysis had to be developed to obtain reliable effective diffusion coefficients. The results show that the diffusion coefficients of water and salts increase with the porosity of the permeable layer, as expected from the COLONBO model. Overall, the direct characterization of the transport properties of the permeable layer and of the pore distribution in the permeable layer validate quantitatively the results obtained with the COLONBO model and the underlying hypotheses. Finally, constitutive models describing the leaching of elements from polymer matrices immersed in water have been applied to bituminized waste materials. With respect to COLONBO, these models account for the effect of mechanical properties of polymers on swelling and leach rates. (author)

  10. Les principes distributifs des mesures d’insertion des jeunes à l’épreuve du longitudinal Youth integration measures and their criteria tested by a longitudinal approach

    Directory of Open Access Journals (Sweden)

    Léa Lima

    2009-07-01

    Full Text Available La sélection des bénéficiaires des mesures d’action sociale relève d’un problème éthique qui fait l’objet d’une intense activité cognitive et normative de la part d’acteurs publics outillés par l’expertise. Or, l’examen historique des principes distributifs mobilisés dans les politiques d’insertion des jeunes donne à voir la reformulation des référentiels de l’action publique dans un cadre longitudinal ainsi que ses effets sur les présupposés éthiques des politiques. Le principe de discrimination positive consistant à redistribuer les chances d’insertion en faveur des jeunes les moins formés a été énoncé au sein d’une représentation instantanéiste de l’insertion des jeunes. Il perd de sa validité avec l’institutionnalisation des trajectoires. L’éthique de l’accompagnement du parcours qui devient dominante dans les années 1990 perd de vue les inégalités entre groupes de niveau de formation au profit d’une démarche d’organisation de carrières ascendantes permises par les mesures d’action sociale disponibles.Targeting social programs is an ethical problem for administrators. Therefore, they develop an intense cognitive and normative activity with the help of experts in economics. The history of how funds are allocated in support of youth integration policies shows the longitudinal reframing of public policy and its impact on ethical principles. The principle of affirmative action consisting in redistributing offers among less qualified youth has been formulated according to a static representation of youth integration. It loses its validity with the institutionalization of individual itineraries. The ethic of pathway support that became dominant in the 1990s lost sight of the inequality between groups levels of qualification no longer appeared relevant and gave way to the organization of upwardly mobile careers made possible by the social programs at hand.

  11. 2D compositional modeling of petroleum generation, expulsion and migration in the Southern compartment of the Reconcavo Basin, Brazil; Modelisation compositionnelle 2D de la genese, expulsion et migration du petrole dans le compartiment sud du Bassin de Reconcavo, Bresil

    Energy Technology Data Exchange (ETDEWEB)

    Barroz Penteado, H.L. de

    1999-01-07

    The Reconcavo Basin is part of a rift formed between the Late Jurassic and the Early Cretaceous in northeastern Brazil. The objective of this thesis was the compositional modeling of petroleum generation, expulsion and migration along a cross-section in the Southern Compartment of the basin with the Temispack basin simulation software. A geochemical study of the lacustrine shales of the Gomo Member (Candelas Fm.) has been performed to determine their petroleum potential, the evolution of maturation with depth and changes in petroleum composition. Hydrogen indices of immature kerogens (400-850 mg/g TOC) were shown to be higher than those of whole rocks, thus indicating a retention of Rock-Eval pyrolysis products in the mineral matrix of these type I source rocks. Saturates (30-50% of organic extracts in the immature zone) increase both in absolute and in relative (60-80%) terms in the oil window (2000-2600 m) because of a partial secondary cracking of NSOs and aromatics. After having tested several scenarios of geodynamic evolution between the Aptian and the Oligocene, a variable thickness of post-rift sediments (maximum of 1200 m) has been shown to be necessary to calibrate maturity parameters. Petroleum migration has been modeled to understand migration pathways as well as the role of faults as drains. Thus, two petroleum migration systems have been identified for the Dom Joao and Cexis accumulations. Petroleum compositional variations have been modeled by coupling the processes of retention and secondary cracking. A good calibration of compositions was obtained with secondary cracking parameters for NSOs and aromatics which are close to those of the main primary cracking reaction of a type I kerogen, coupled with a retention of 50% of NSOs within the source rocks. (author)

  12. Model-Based GUI Testing Using Uppaal at Novo Nordisk

    Science.gov (United States)

    Hjort, Ulrik H.; Illum, Jacob; Larsen, Kim G.; Petersen, Michael A.; Skou, Arne

    This paper details a collaboration between Aalborg University and Novo Nordiskin developing an automatic model-based test generation tool for system testing of the graphical user interface of a medical device on an embedded platform. The tool takes as input an UML Statemachine model and generates a test suite satisfying some testing criterion, such as edge or state coverage, and converts the individual test case into a scripting language that can be automatically executed against the target. The tool has significantly reduced the time required for test construction and generation, and reduced the number of test scripts while increasing the coverage.

  13. Cost-Effective Remediation of Depleted Uranium (DU) at Environmental Restoration Sites

    International Nuclear Information System (INIS)

    MILLER, MARK; GALLOWAY, ROBERT B.; VANDERPOEL, GLENN; JOHNSON, ED; COPLAND, JOHN; SALAZAR, MICHAEL

    1999-01-01

    Numerous sites in the United States and around the world are contaminated with depleted uranium (DU) in various forms. A prevalent form is fragmented DU originating from various scientific tests involving high explosives and DU during weapon-development programs, at firing practice ranges, or in war theaters where DU was used in armor-piercing projectiles. The contamination at these sites is typically very heterogeneous, with discrete, visually identifiable DU fragments mixed with native soil. The bulk-averaged DU activity is quite low, whereas DU fragments, which are distinct from the soil matrix, have much higher specific activity. DU is best known as a dark metal that is nearly twice as dense as lead, but DU in the environment readily weathers (oxidizes) to a distinctive bright yellow color that is quite visible. While the specific activity (amount of radioactivity per mass of soil) of DU is relatively low and presents only a minor radiological hazard, the fact that DU is radioactive and visually identifiable makes it desirable to remove the DU ''contamination'' from the environment. The typical approach to conducting this DU remediation is to use radiation-detection instruments to identify the contaminant and then to separate it from the adjacent soil, packaging it for disposal as radioactive waste. This process can be performed manually or by specialized, automated equipment. Alternatively, a more cost-effective approach might be simple mechanical or gravimetric separation of the DU fragments from the host soil matrix. At SNL/NM, both the automated and simple mechanical approaches have recently been employed. This paper discusses the pros/cons of the two approaches

  14. A Model for Random Student Drug Testing

    Science.gov (United States)

    Nelson, Judith A.; Rose, Nancy L.; Lutz, Danielle

    2011-01-01

    The purpose of this case study was to examine random student drug testing in one school district relevant to: (a) the perceptions of students participating in competitive extracurricular activities regarding drug use and abuse; (b) the attitudes and perceptions of parents, school staff, and community members regarding student drug involvement; (c)…

  15. Testing Pearl Model In Three European Sites

    Science.gov (United States)

    Bouraoui, F.; Bidoglio, G.

    The Plant Protection Product Directive (91/414/EEC) stresses the need of validated models to calculate predicted environmental concentrations. The use of models has become an unavoidable step before pesticide registration. In this context, European Commission, and in particular DGVI, set up a FOrum for the Co-ordination of pes- ticide fate models and their USe (FOCUS). In a complementary effort, DG research supported the APECOP project, with one of its objective being the validation and im- provement of existing pesticide fate models. The main topic of research presented here is the validation of the PEARL model for different sites in Europe. The PEARL model, actually used in the Dutch pesticide registration procedure, was validated in three well- instrumented sites: Vredepeel (the Netherlands), Brimstone (UK), and Lanna (Swe- den). A step-wise procedure was used for the validation of the PEARL model. First the water transport module was calibrated, and then the solute transport module, using tracer measurements keeping unchanged the water transport parameters. The Vrede- peel site is characterised by a sandy soil. Fourteen months of measurements were used for the calibration. Two pesticides were applied on the site: bentazone and etho- prophos. PEARL predictions were very satisfactory for both soil moisture content, and pesticide concentration in the soil profile. The Brimstone site is characterised by a cracking clay soil. The calibration was conducted on a time series measurement of 7 years. The validation consisted in comparing predictions and measurement of soil moisture at different soil depths, and in comparing the predicted and measured con- centration of isoproturon in the drainage water. The results, even if in good agreement with the measuremens, highlighted the limitation of the model when the preferential flow becomes a dominant process. PEARL did not reproduce well soil moisture pro- file during summer months, and also under-predicted the arrival of

  16. INTRAVAL test case 1b - modelling results

    International Nuclear Information System (INIS)

    Jakob, A.; Hadermann, J.

    1991-07-01

    This report presents results obtained within Phase I of the INTRAVAL study. Six different models are fitted to the results of four infiltration experiments with 233 U tracer on small samples of crystalline bore cores originating from deep drillings in Northern Switzerland. Four of these are dual porosity media models taking into account advection and dispersion in water conducting zones (either tubelike veins or planar fractures), matrix diffusion out of these into pores of the solid phase, and either non-linear or linear sorption of the tracer onto inner surfaces. The remaining two are equivalent porous media models (excluding matrix diffusion) including either non-linear sorption onto surfaces of a single fissure family or linear sorption onto surfaces of several different fissure families. The fits to the experimental data have been carried out by Marquardt-Levenberg procedure yielding error estimates of the parameters, correlation coefficients and also, as a measure for the goodness of the fits, the minimum values of the χ 2 merit function. The effects of different upstream boundary conditions are demonstrated and the penetration depth for matrix diffusion is discussed briefly for both alternative flow path scenarios. The calculations show that the dual porosity media models are significantly more appropriate to the experimental data than the single porosity media concepts. Moreover, it is matrix diffusion rather than the non-linearity of the sorption isotherm which is responsible for the tailing part of the break-through curves. The extracted parameter values for some models for both the linear and non-linear (Freundlich) sorption isotherms are consistent with the results of independent static batch sorption experiments. From the fits, it is generally not possible to discriminate between the two alternative flow path geometries. On the basis of the modelling results, some proposals for further experiments are presented. (author) 15 refs., 23 figs., 7 tabs

  17. Testing a Dilaton Gravity Model Using Nucleosynthesis

    International Nuclear Information System (INIS)

    Boran, S.; Kahya, E. O.

    2014-01-01

    Big bang nucleosynthesis (BBN) offers one of the most strict evidences for the Λ-CDM cosmology at present, as well as the cosmic microwave background (CMB) radiation. In this work, our main aim is to present the outcomes of our calculations related to primordial abundances of light elements, in the context of higher dimensional steady-state universe model in the dilaton gravity. Our results show that abundances of light elements (primordial D, 3 He, 4 He, T, and 7 Li) are significantly different for some cases, and a comparison is given between a particular dilaton gravity model and Λ-CDM in the light of the astrophysical observations

  18. Testing Software Development Project Productivity Model

    Science.gov (United States)

    Lipkin, Ilya

    Software development is an increasingly influential factor in today's business environment, and a major issue affecting software development is how an organization estimates projects. If the organization underestimates cost, schedule, and quality requirements, the end results will not meet customer needs. On the other hand, if the organization overestimates these criteria, resources that could have been used more profitably will be wasted. There is no accurate model or measure available that can guide an organization in a quest for software development, with existing estimation models often underestimating software development efforts as much as 500 to 600 percent. To address this issue, existing models usually are calibrated using local data with a small sample size, with resulting estimates not offering improved cost analysis. This study presents a conceptual model for accurately estimating software development, based on an extensive literature review and theoretical analysis based on Sociotechnical Systems (STS) theory. The conceptual model serves as a solution to bridge organizational and technological factors and is validated using an empirical dataset provided by the DoD. Practical implications of this study allow for practitioners to concentrate on specific constructs of interest that provide the best value for the least amount of time. This study outlines key contributing constructs that are unique for Software Size E-SLOC, Man-hours Spent, and Quality of the Product, those constructs having the largest contribution to project productivity. This study discusses customer characteristics and provides a framework for a simplified project analysis for source selection evaluation and audit task reviews for the customers and suppliers. Theoretical contributions of this study provide an initial theory-based hypothesized project productivity model that can be used as a generic overall model across several application domains such as IT, Command and Control

  19. Model techniques for testing heated concrete structures

    International Nuclear Information System (INIS)

    Stefanou, G.D.

    1983-01-01

    Experimental techniques are described which may be used in the laboratory to measure strains of model concrete structures representing to scale actual structures of any shape or geometry, operating at elevated temperatures, for which time-dependent creep and shrinkage strains are dominant. These strains could be used to assess the distribution of stress in the scaled structure and hence to predict the actual behaviour of concrete structures used in nuclear power stations. Similar techniques have been employed in an investigation to measure elastic, thermal, creep and shrinkage strains in heated concrete models representing to scale parts of prestressed concrete pressure vessels for nuclear reactors. (author)

  20. Experimental tests of proton spin models

    International Nuclear Information System (INIS)

    Ramsey, G.P.; Argonne National Lab., IL

    1989-01-01

    We have developed models for the spin-weighted quark and gluon distribution in a longitudinally polarized proton. The model parameters are determined from current algebra sum rules and polarized deep-inelastic scattering data. A number of different scenarios are presented for the fraction of spin carried the constituent parton distributions. A possible long-range experimental program is suggested for measuring various hard scattering processes using polarized lepton and proton beams. With the knowledge gained from these experiments, we can begin to understand the parton contributions to the proton spin. 28 refs., 5 figs

  1. Port Adriano, 2D-Model tests

    DEFF Research Database (Denmark)

    Burcharth, Hans F.; Meinert, Palle; Andersen, Thomas Lykke

    the crown wall have been measured. The model has been subjected to irregular waves corresponding to typical conditions offshore from the intended prototype location. Characteristic situations have been video recorded. The stability of the toe has been investigated. The wave-generated forces on the caisson...

  2. Damage modeling in Small Punch Test specimens

    DEFF Research Database (Denmark)

    Martínez Pañeda, Emilio; Cuesta, I.I.; Peñuelas, I.

    2016-01-01

    . Furthermore,Gurson-Tvergaard-Needleman model predictions from a top-down approach are employed to gain insightinto the mechanisms governing crack initiation and subsequent propagation in small punch experiments.An accurate assessment of micromechanical toughness parameters from the SPT...

  3. Testing structural stability in macroeconometric models

    NARCIS (Netherlands)

    Boldea, O.; Hall, A.R.; Hashimzade, N.; Thornton, M.A.

    2013-01-01

    Since the earliest days of macroeconometric analysis, researchers have been concerned about the appropriateness of the assumption that model parameters remain constant over long periods of time; for example see Tinbergen (1939). This concern is also central to the so-called Lucas (1976) critique

  4. Model Testing - Bringing the Ocean into the Laboratory

    DEFF Research Database (Denmark)

    Aage, Christian

    2000-01-01

    Hydrodynamic model testing, the principle of bringing the ocean into the laboratory to study the behaviour of the ocean itself and the response of man-made structures in the ocean in reduced scale, has been known for centuries. Due to an insufficient understanding of the physics involved, however......, the early model tests often gave incomplete or directly misleading results.This keynote lecture deals with some of the possibilities and problems within the field of hydrodynamic and hydraulic model testing....

  5. Sodium purification in Rapsodie; La purification du sodium a Rapsodie

    Energy Technology Data Exchange (ETDEWEB)

    Giraud, B [Commissariat a l' Energie Atomique, Dir. des Piles Atomiques, Cadarache (France). Centre d' Etudes Nucleaires

    1968-07-01

    This report is one of a series of publications presenting the main results of tests carried out during the start-up of the first french fast neutron reactor: Rapsodie. The article presents the sodium purification techniques used in the reactor cooling circuits both from the constructional point of view and with respect to results obtained during the first years working. (author) [French] Ce rapport fait partie d'une serie de publications presentant l'essentiel des resultats des essais effectues a l'occasion du demarrage du premier reacteur francais a neutrons rapides: RAPSODIE. Cet article expose les techniques de la purification du sodium utilise dans les circuits de refroidissement du reacteur tant au point de vue de leur realisation technologique, que des resultats obtenus pendant la premiere annee de fonctionnement. (auteur)

  6. The biokinetics of uranium migrating from embedded DU fragments

    International Nuclear Information System (INIS)

    Leggett, R.W.; Pellmar, T.C.

    2003-01-01

    Military uses of depleted uranium (DU) munitions have resulted in casualties with embedded DU fragments. Assessment of radiological or chemical health risks from these fragments requires a model relating urinary U to the rate of migration of U from the fragments, and its accumulation in systemic tissues. A detailed biokinetic model for U has been published by the International Commission on Radiological Protection (ICRP), but its applicability to U migrating from embedded DU fragments is uncertain. Recently, ) conducted a study at the Armed Forces Radiobiology Research Institute (AFRRI) on the redistribution and toxicology of U in rats with implanted DU pellets, simulating embedded fragments. This paper compares the biokinetic data from that study with the behavior of commonly studied forms of U in rats (e.g., intravenously injected U nitrate). The comparisons indicate that the biokinetics of U migrating from embedded DU is similar to that of commonly studied forms of U with regard to long-term accumulation in kidneys, bone, and liver. The results provide limited support for the application of the ICRP's model to persons with embedded DU fragments. Additional information is needed with regard to the short-term behavior of migrating U and its accumulation in lymph nodes, brain, testicles, and other infrequently studied U repositories

  7. Model tests in RAMONA and NEPTUN

    International Nuclear Information System (INIS)

    Hoffmann, H.; Ehrhard, P.; Weinberg, D.; Carteciano, L.; Dres, K.; Frey, H.H.; Hayafune, H.; Hoelle, C.; Marten, K.; Rust, K.; Thomauske, K.

    1995-01-01

    In order to demonstrate passive decay heat removal (DHR) in an LMR such as the European Fast Reactor, the RAMONA and NEPTUN facilities, with water as a coolant medium, were used to measure transient flow data corresponding to a transition from forced convection (under normal operation) to natural convection under DHR conditions. The facilities were 1:20 and 1:5 models, respectively, of a pool-type reactor including the IHXs, pumps, and immersed coolers. Important results: The decay heat can be removed from all parts of the primary system by natural convection, even if the primary fluid circulation through the IHX is interrupted. This result could be transferred to liquid metal cooling by experiments in models with thermohydraulic similarity. (orig.)

  8. Tests and comparisons of gravity models.

    Science.gov (United States)

    Marsh, J. G.; Douglas, B. C.

    1971-01-01

    Optical observations of the GEOS satellites were used to obtain orbital solutions with different sets of geopotential coefficients. The solutions were compared before and after modification to high order terms (necessary because of resonance) and were then analyzed by comparing subsequent observations with predicted trajectories. The most important source of error in orbit determination and prediction for the GEOS satellites is the effect of resonance found in most published sets of geopotential coefficients. Modifications to the sets yield greatly improved orbits in most cases. The results of these comparisons suggest that with the best optical tracking systems and gravity models, satellite position error due to gravity model uncertainty can reach 50-100 m during a heavily observed 5-6 day orbital arc. If resonant coefficients are estimated, the uncertainty is reduced considerably.

  9. A magnetorheological actuation system: test and model

    International Nuclear Information System (INIS)

    John, Shaju; Chaudhuri, Anirban; Wereley, Norman M

    2008-01-01

    Self-contained actuation systems, based on frequency rectification of the high frequency motion of an active material, can produce high force and stroke output. Magnetorheological (MR) fluids are active fluids whose rheological properties can be altered by the application of a magnetic field. By using MR fluids as the energy transmission medium in such hybrid devices, a valving system with no moving parts can be implemented and used to control the motion of an output cylinder shaft. The MR fluid based valves are configured in the form of an H-bridge to produce bi-directional motion in an output cylinder by alternately applying magnetic fields in the two opposite arms of the bridge. The rheological properties of the MR fluid are modeled using both Bingham plastic and bi-viscous models. In this study, the primary actuation is performed using a compact terfenol-D rod driven pump and frequency rectification of the rod motion is done using passive reed valves. The pump and reed valve configuration along with MR fluidic valves form a compact hydraulic actuation system. Actuator design, analysis and experimental results are presented in this paper. A time domain model of the actuator is developed and validated using experimental data

  10. Archives: les cahiers du cread

    African Journals Online (AJOL)

    Items 1 - 24 of 24 ... Archives: les cahiers du cread. Journal Home > Archives: les cahiers du cread. Log in or Register to get access to full text downloads. Username, Password, Remember me, or Register · Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives. 1 - 24 of 24 Items. 2016 ...

  11. Le commerce du Nord

    OpenAIRE

    Pourchasse, Pierrick; Bouëdec, Gérard Le

    2015-01-01

    Au XVIIIe siècle, la France s'approvisionne abondamment dans les pays du Nord : bois, chanvre et goudron de la Baltique, tonnellerie de Poméranie, pêche de rogue de Norvège, graines de lin de Courlande, barres de fer suédois… Sa balance commerciale est pourtant positive grâce aux sels, aux vins et surtout des nouvelles marchandises coloniales. Or, la plupart des transactions passent par l’incontournable intermédiaire hollandais. Les explications sur l’absence des Français dans le Nord sont re...

  12. La voie du Centre

    OpenAIRE

    2017-01-01

    Après avoir quelque peu louvoyé dans un discours apparemment anarchique où les souvenirs semblent se bousculer sans autre fil conducteur que la référence obsédante au mal satanique, brusquement le narrateur annonce un événement primordial : Foi um fato que se deu, um dia, se abriu. O primeiro. Depois o senhor verá por quê, me devolvendo minha razão (79). Cette introduction situe la rencontre du Menino comme fondatrice d’un destin dont il reviendrait au narrataire de dégager les enchaînements....

  13. Bulletin du CRDI #126

    International Development Research Centre (IDRC) Digital Library (Canada)

    26 févr. 2018 ... Dans ce numéro, découvrez comment la recherche financée par le CRDI permet d'améliorer la santé des mères et des enfants dans les pays du Sud et comment les innovations techniques et sociales de l'initiative SEARCH permettent de surmonter les défis liés à la cybersanté. N'oubliez pas non plus de ...

  14. Prévalence du VIH chez la Femme Enceinte et Transmission Mère ...

    African Journals Online (AJOL)

    Une meilleure organisation des stratégies de réduction de la transmission mèreenfant du VIH/SIDA, même dans un environnement à ressources limitées, peut conduire à des résultats similaires à ceux des pays du Nord. A la lumière de cette étude, nous recommandons fortement un deuxième test du VIH au 3ème rimestre ...

  15. Prévalence du VIH chez la Femme Enceinte et Transmission Mère ...

    African Journals Online (AJOL)

    Mère-Enfant du VIH à la Maternité de l'Hôpital Général de. Douala, Cameroun. K. J. Tsingaing,1 O. T. Egbe,1 G. ... Mots Clés prévalence du VIH ; femme enceinte ; transmis- sion mère-enfant du VIH. 1 Introduction .... HIV test to rescreen women in the third trimester of pregnancy,. J Midwifery Womens Health, 54 (2009), ...

  16. Bayesian models based on test statistics for multiple hypothesis testing problems.

    Science.gov (United States)

    Ji, Yuan; Lu, Yiling; Mills, Gordon B

    2008-04-01

    We propose a Bayesian method for the problem of multiple hypothesis testing that is routinely encountered in bioinformatics research, such as the differential gene expression analysis. Our algorithm is based on modeling the distributions of test statistics under both null and alternative hypotheses. We substantially reduce the complexity of the process of defining posterior model probabilities by modeling the test statistics directly instead of modeling the full data. Computationally, we apply a Bayesian FDR approach to control the number of rejections of null hypotheses. To check if our model assumptions for the test statistics are valid for various bioinformatics experiments, we also propose a simple graphical model-assessment tool. Using extensive simulations, we demonstrate the performance of our models and the utility of the model-assessment tool. In the end, we apply the proposed methodology to an siRNA screening and a gene expression experiment.

  17. Mixed Portmanteau Test for Diagnostic Checking of Time Series Models

    Directory of Open Access Journals (Sweden)

    Sohail Chand

    2014-01-01

    Full Text Available Model criticism is an important stage of model building and thus goodness of fit tests provides a set of tools for diagnostic checking of the fitted model. Several tests are suggested in literature for diagnostic checking. These tests use autocorrelation or partial autocorrelation in the residuals to criticize the adequacy of fitted model. The main idea underlying these portmanteau tests is to identify if there is any dependence structure which is yet unexplained by the fitted model. In this paper, we suggest mixed portmanteau tests based on autocorrelation and partial autocorrelation functions of the residuals. We derived the asymptotic distribution of the mixture test and studied its size and power using Monte Carlo simulations.

  18. Optical analysis of pollution transport in geotechnical centrifuge tests; Analyse optique du transport de polluant lors d'essais geotechniques en centrifugeuse

    Energy Technology Data Exchange (ETDEWEB)

    Allersma, H.G.B. [Delft University of Technology, Faculty of Chemical Technology and Materials Sciences, Delft (Netherlands); Esposito, G.M. [Delft University of Technology, TNO-Building and Construction Research, Formerly Delft (Netherlands)

    2000-07-01

    An optical method based on image processing techniques has been described for performing measurements on pollution transport phenomena in soil in centrifuge tests. The geometry of the polluted areas as well as the concentration of the pollution can be measured in two-dimensional tests. (author)

  19. Upgraded Analytical Model of the Cylinder Test

    Energy Technology Data Exchange (ETDEWEB)

    Souers, P. Clark [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States). Energetic Materials Center; Lauderbach, Lisa [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States). Energetic Materials Center; Garza, Raul [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States). Energetic Materials Center; Ferranti, Louis [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States). Energetic Materials Center; Vitello, Peter [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States). Energetic Materials Center

    2013-03-15

    A Gurney-type equation was previously corrected for wall thinning and angle of tilt, and now we have added shock wave attenuation in the copper wall and air gap energy loss. Extensive calculations were undertaken to calibrate the two new energy loss mechanisms across all explosives. The corrected Gurney equation is recommended for cylinder use over the original 1943 form. The effect of these corrections is to add more energy to the adiabat values from a relative volume of 2 to 7, with low energy explosives having the largest correction. The data was pushed up to a relative volume of about 15 and the JWL parameter ω was obtained directly. Finally, the total detonation energy density was locked to the v = 7 adiabat energy density, so that the Cylinder test gives all necessary values needed to make a JWL.

  20. Upgraded Analytical Model of the Cylinder Test

    Energy Technology Data Exchange (ETDEWEB)

    Souers, P. Clark; Lauderbach, Lisa; Garza, Raul; Ferranti, Louis; Vitello, Peter

    2013-03-15

    A Gurney-type equation was previously corrected for wall thinning and angle of tilt, and now we have added shock wave attenuation in the copper wall and air gap energy loss. Extensive calculations were undertaken to calibrate the two new energy loss mechanisms across all explosives. The corrected Gurney equation is recommended for cylinder use over the original 1943 form. The effect of these corrections is to add more energy to the adiabat values from a relative volume of 2 to 7, with low energy explosives having the largest correction. The data was pushed up to a relative volume of about 15 and the JWL parameter ω was obtained directly. The total detonation energy density was locked to the v=7 adiabat energy density, so that the Cylinder test gives all necessary values needed to make a JWL.

  1. Model tests on dynamic performance of RC shear walls

    International Nuclear Information System (INIS)

    Nagashima, Toshio; Shibata, Akenori; Inoue, Norio; Muroi, Kazuo.

    1991-01-01

    For the inelastic dynamic response analysis of a reactor building subjected to earthquakes, it is essentially important to properly evaluate its restoring force characteristics under dynamic loading condition and its damping performance. Reinforced concrete shear walls are the main structural members of a reactor building, and dominate its seismic behavior. In order to obtain the basic information on the dynamic restoring force characteristics and damping performance of shear walls, the dynamic test using a large shaking table, static displacement control test and the pseudo-dynamic test on the models of a shear wall were conducted. In the dynamic test, four specimens were tested on a large shaking table. In the static test, four specimens were tested, and in the pseudo-dynamic test, three specimens were tested. These tests are outlined. The results of these tests were compared, placing emphasis on the restoring force characteristics and damping performance of the RC wall models. The strength was higher in the dynamic test models than in the static test models mainly due to the effect of loading rate. (K.I.)

  2. Choeur du CERN : Concert

    CERN Multimedia

    CERN Choir

    2017-01-01

    Une œuvre à découvrir! La grande Missa pro defunctis de François-Joseph Gossec (1734-1829) est le chef-d’œuvre tôt venu (à vingt-cinq ans) d’un compositeur qui vivra encore 70 ans après sa création. Elle a connu la gloire, puis s’est fait un peu oublier. Pas du tout le monde cependant : des musicologues ont montré ce que le Requiem de Mozart lui devait ; et il suffit de l’avoir entendue pour comprendre pourquoi Berlioz (qui avait vingt-six ans à la mort de Gossec) en a été impressionné : les nombreux cuivres et bois répartis dans des endroits plus ou moins cachés de la salle de concert pour exprimer les frayeurs du Jugement dernier annoncent son Requiem – et celui de Verdi. Mais « plus encore que par...

  3. Les risques du travail

    CERN Document Server

    Thébaud-Mony, Annie

    2015-01-01

    Depuis les années 1990, les conditions de travail se sont peu à peu imposées dans le débat social. Néanmoins, la situation reste critique. Les risques traditionnels n'ont pas disparu : les manutentions lourdes, l'exposition professionnelle aux cancérogènes, au bruit ou aux vibrations demeurent répandues... De plus, certaines " améliorations " n'ont fait que déplacer et dissimuler les problèmes, telle l'externalisation des risques grâce à la sous-traitance. Dans le même temps, les transformations du travail et des modalités de gestion de la main-d'œuvre ont fragilisé les collectifs et accru l'isolement des salariés, conduisant à une montée visible de la souffrance psychique. Face à ces évolutions, il est plus que jamais nécessaire que tous les acteurs concernés, en particulier les salariés eux-mêmes et leurs représentants, s'approprient les connaissances indispensables pour améliorer la protection de la santé sur les lieux du travail. Tel est le but de ce livre, qui renouvelle int�...

  4. Model-Based GUI Testing Using Uppaal at Novo Nordisk

    DEFF Research Database (Denmark)

    H. Hjort, Ulrik; Rasmussen, Jacob Illum; Larsen, Kim Guldstrand

    2009-01-01

    This paper details a collaboration between Aalborg University and Novo Nordiskin developing an automatic model-based test generation tool for system testing of the graphical user interface of a medical device on an embedded platform. The tool takes as input an UML Statemachine model and generates...

  5. A Bootstrap Cointegration Rank Test for Panels of VAR Models

    DEFF Research Database (Denmark)

    Callot, Laurent

    functions of the individual Cointegrated VARs (CVAR) models. A bootstrap based procedure is used to compute empirical distributions of the trace test statistics for these individual models. From these empirical distributions two panel trace test statistics are constructed. The satisfying small sample...

  6. GENERATING TEST CASES FOR PLATFORM INDEPENDENT MODEL BY USING USE CASE MODEL

    OpenAIRE

    Hesham A. Hassan,; Zahraa. E. Yousif

    2010-01-01

    Model-based testing refers to testing and test case generation based on a model that describes the behavior of the system. Extensive use of models throughout all the phases of software development starting from the requirement engineering phase has led to increased importance of Model Based Testing. The OMG initiative MDA has revolutionized the way models would be used for software development. Ensuring that all user requirements are addressed in system design and the design is getting suffic...

  7. Conformance test development with the Java modeling language

    DEFF Research Database (Denmark)

    Søndergaard, Hans; Korsholm, Stephan E.; Ravn, Anders P.

    2017-01-01

    In order to claim conformance with a Java Specification Request, a Java implementation has to pass all tests in an associated Technology Compatibility Kit (TCK). This paper presents a model-based development of a TCK test suite and a test execution tool for the draft Safety-Critical Java (SCJ......) profile specification. The Java Modeling Language (JML) is used to model conformance constraints for the profile. JML annotations define contracts for classes and interfaces. The annotations are translated by a tool into runtime assertion checks.Hereby the design and elaboration of the concrete test cases...

  8. An alternative for cost-effective remediation of depleted uranium (DU) at certain environmental restoration sites.

    Science.gov (United States)

    Miller, M; Galloway, B; VanDerpoel, G; Johnson, E; Copland, J; Salazar, M

    2000-02-01

    Numerous sites in the United States and around the world are contaminated with depleted uranium (DU) in various forms. A prevalent form is fragmented DU originating from various scientific tests involving high explosives and DU during weapon development programs, at firing practice ranges, or war theaters where DU was used in armor-piercing projectiles. The contamination at these sites is typically very heterogeneous, with discreet, visually identifiable DU fragments mixed with native soil. That is, the bulk-averaged DU activity is quite low, while specific DU fragments, which are distinct from the soil matrix, have much higher specific activity. DU is best known as a dark, black metal that is nearly twice as dense as lead, but DU in the environment readily weathers (oxidizes) to a distinctive bright yellow color that is readily visible. While the specific activity (amount of radioactivity per mass of soil) of DU is relatively low and presents only a minor radiological hazard, the fact that it is radioactive and visually identifiable makes it desirable to remove the DU "contamination" from the environment. The typical approach to conducting this DU remediation is to use radiation detection instruments to identify the contaminant and separate it from the adjacent soil, packaging it for disposal as radioactive waste. This process can be performed manually or by specialized, automated equipment. Alternatively, in certain situations a more cost-effective approach might be simple mechanical or gravimetric separation of the DU fragments from the host soil matrix. At SNL/NM, both the automated and simple mechanical approaches have recently been employed. This paper discusses the pros/cons of the two approaches.

  9. Collider tests of the Renormalizable Coloron Model

    Energy Technology Data Exchange (ETDEWEB)

    Bai, Yang; Dobrescu, Bogdan A.

    2018-04-01

    The coloron, a massive version of the gluon present in gauge extensions of QCD, has been searched for at the LHC as a dijet or top quark pair resonance. We point out that in the Renormalizable Coloron Model (ReCoM) with a minimal field content to break the gauge symmetry, a color-octet scalar and a singlet scalar are naturally lighter than the coloron because they are pseudo Nambu-Goldstone bosons. Consequently, the coloron may predominantly decay into scalar pairs, leading to novel signatures at the LHC. When the color-octet scalar is lighter than the singlet, or when the singlet mass is above roughly 1 TeV, the signatures consist of multi-jet resonances of multiplicity up to 12, including topologies with multi-prong jet substructure, slightly displaced vertices, and sometimes a top quark pair. When the singlet is the lightest ReCoM boson and lighter than about 1 TeV, its main decays ($W^+W^-$, $\\gamma Z$, $ZZ$) arise at three loops. The LHC signatures then involve two or four boosted electroweak bosons, often originating from highly displaced vertices, plus one or two pairs of prompt jets or top quarks.

  10. Glide back booster wind tunnel model testing

    Science.gov (United States)

    Pricop, M. V.; Cojocaru, M. G.; Stoica, C. I.; Niculescu, M. L.; Neculaescu, A. M.; Persinaru, A. G.; Boscoianu, M.

    2017-07-01

    Affordable space access requires partial or ideally full launch vehicle reuse, which is in line with clean environment requirement. Although the idea is old, the practical use is difficult, requiring very large technology investment for qualification. Rocket gliders like Space Shuttle have been successfullyoperated but the price and correspondingly the energy footprint were found not sustainable. For medium launchers, finally there is a very promising platform as Falcon 9. For very small launchers the situation is more complex, because the performance index (payload to start mass) is already small, versus medium and heavy launchers. For partial reusable micro launchers this index is even smaller. However the challenge has to be taken because it is likely that in a multiyear effort, technology is going to enable the performance recovery to make such a system economically and environmentally feasible. The current paper is devoted to a small unitary glide back booster which is foreseen to be assembled in a number of possible configurations. Although the level of analysis is not deep, the solution is analyzed from the aerodynamic point of view. A wind tunnel model is designed, with an active canard, to enablea more efficient wind tunnel campaign, as a national level premiere.

  11. Economic contract theory tests models of mutualism.

    Science.gov (United States)

    Weyl, E Glen; Frederickson, Megan E; Yu, Douglas W; Pierce, Naomi E

    2010-09-07

    Although mutualisms are common in all ecological communities and have played key roles in the diversification of life, our current understanding of the evolution of cooperation applies mostly to social behavior within a species. A central question is whether mutualisms persist because hosts have evolved costly punishment of cheaters. Here, we use the economic theory of employment contracts to formulate and distinguish between two mechanisms that have been proposed to prevent cheating in host-symbiont mutualisms, partner fidelity feedback (PFF) and host sanctions (HS). Under PFF, positive feedback between host fitness and symbiont fitness is sufficient to prevent cheating; in contrast, HS posits the necessity of costly punishment to maintain mutualism. A coevolutionary model of mutualism finds that HS are unlikely to evolve de novo, and published data on legume-rhizobia and yucca-moth mutualisms are consistent with PFF and not with HS. Thus, in systems considered to be textbook cases of HS, we find poor support for the theory that hosts have evolved to punish cheating symbionts; instead, we show that even horizontally transmitted mutualisms can be stabilized via PFF. PFF theory may place previously underappreciated constraints on the evolution of mutualism and explain why punishment is far from ubiquitous in nature.

  12. Item Response Theory Models for Performance Decline during Testing

    Science.gov (United States)

    Jin, Kuan-Yu; Wang, Wen-Chung

    2014-01-01

    Sometimes, test-takers may not be able to attempt all items to the best of their ability (with full effort) due to personal factors (e.g., low motivation) or testing conditions (e.g., time limit), resulting in poor performances on certain items, especially those located toward the end of a test. Standard item response theory (IRT) models fail to…

  13. Testing Model with "Check Technique" for Physics Education

    Science.gov (United States)

    Demir, Cihat

    2016-01-01

    As the number, date and form of the written tests are structured and teacher-oriented, it is considered that it creates fear and anxiety among the students. It has been found necessary and important to form a testing model which will keep the students away from the test anxiety and allows them to learn only about the lesson. For this study,…

  14. Testing of materials and scale models for impact limiters

    International Nuclear Information System (INIS)

    Maji, A.K.; Satpathi, D.; Schryer, H.L.

    1991-01-01

    Aluminum Honeycomb and Polyurethane foam specimens were tested to obtain experimental data on the material's behavior under different loading conditions. This paper reports the dynamic tests conducted on the materials and on the design and testing of scale models made out of these open-quotes Impact Limiters,close quotes as they are used in the design of transportation casks. Dynamic tests were conducted on a modified Charpy Impact machine with associated instrumentation, and compared with static test results. A scale model testing setup was designed and used for preliminary tests on models being used by current designers of transportation casks. The paper presents preliminary results of the program. Additional information will be available and reported at the time of presentation of the paper

  15. Bankruptcy risk model and empirical tests

    Science.gov (United States)

    Podobnik, Boris; Horvatic, Davor; Petersen, Alexander M.; Urošević, Branko; Stanley, H. Eugene

    2010-01-01

    We analyze the size dependence and temporal stability of firm bankruptcy risk in the US economy by applying Zipf scaling techniques. We focus on a single risk factor—the debt-to-asset ratio R—in order to study the stability of the Zipf distribution of R over time. We find that the Zipf exponent increases during market crashes, implying that firms go bankrupt with larger values of R. Based on the Zipf analysis, we employ Bayes’s theorem and relate the conditional probability that a bankrupt firm has a ratio R with the conditional probability of bankruptcy for a firm with a given R value. For 2,737 bankrupt firms, we demonstrate size dependence in assets change during the bankruptcy proceedings. Prepetition firm assets and petition firm assets follow Zipf distributions but with different exponents, meaning that firms with smaller assets adjust their assets more than firms with larger assets during the bankruptcy process. We compare bankrupt firms with nonbankrupt firms by analyzing the assets and liabilities of two large subsets of the US economy: 2,545 Nasdaq members and 1,680 New York Stock Exchange (NYSE) members. We find that both assets and liabilities follow a Pareto distribution. The finding is not a trivial consequence of the Zipf scaling relationship of firm size quantified by employees—although the market capitalization of Nasdaq stocks follows a Pareto distribution, the same distribution does not describe NYSE stocks. We propose a coupled Simon model that simultaneously evolves both assets and debt with the possibility of bankruptcy, and we also consider the possibility of firm mergers. PMID:20937903

  16. Matrix diffusion model. In situ tests using natural analogues

    Energy Technology Data Exchange (ETDEWEB)

    Rasilainen, K. [VTT Energy, Espoo (Finland)

    1997-11-01

    Matrix diffusion is an important retarding and dispersing mechanism for substances carried by groundwater in fractured bedrock. Natural analogues provide, unlike laboratory or field experiments, a possibility to test the model of matrix diffusion in situ over long periods of time. This thesis documents quantitative model tests against in situ observations, done to support modelling of matrix diffusion in performance assessments of nuclear waste repositories. 98 refs. The thesis includes also eight previous publications by author.

  17. Matrix diffusion model. In situ tests using natural analogues

    International Nuclear Information System (INIS)

    Rasilainen, K.

    1997-11-01

    Matrix diffusion is an important retarding and dispersing mechanism for substances carried by groundwater in fractured bedrock. Natural analogues provide, unlike laboratory or field experiments, a possibility to test the model of matrix diffusion in situ over long periods of time. This thesis documents quantitative model tests against in situ observations, done to support modelling of matrix diffusion in performance assessments of nuclear waste repositories

  18. DKIST enclosure modeling and verification during factory assembly and testing

    Science.gov (United States)

    Larrakoetxea, Ibon; McBride, William; Marshall, Heather K.; Murga, Gaizka

    2014-08-01

    The Daniel K. Inouye Solar Telescope (DKIST, formerly the Advanced Technology Solar Telescope, ATST) is unique as, apart from protecting the telescope and its instrumentation from the weather, it holds the entrance aperture stop and is required to position it with millimeter-level accuracy. The compliance of the Enclosure design with the requirements, as of Final Design Review in January 2012, was supported by mathematical models and other analyses which included structural and mechanical analyses (FEA), control models, ventilation analysis (CFD), thermal models, reliability analysis, etc. During the Enclosure Factory Assembly and Testing the compliance with the requirements has been verified using the real hardware and the models created during the design phase have been revisited. The tests performed during shutter mechanism subsystem (crawler test stand) functional and endurance testing (completed summer 2013) and two comprehensive system-level factory acceptance testing campaigns (FAT#1 in December 2013 and FAT#2 in March 2014) included functional and performance tests on all mechanisms, off-normal mode tests, mechanism wobble tests, creation of the Enclosure pointing map, control system tests, and vibration tests. The comparison of the assumptions used during the design phase with the properties measured during the test campaign provides an interesting reference for future projects.

  19. Amélioration des tribunaux du travail au Mexique : le cas de Cuautitlán

    International Development Research Centre (IDRC) Digital Library (Canada)

    Ce projet de recherche dirigé par l'Instituto Tecnológico de México s'intéressera au contexte juridique du pays et aux procédures administratives liées aux décisions et aux ... Monitoring and notification : evidence from a field experiment in a Mexican labor court ... Delay and corruption : a simple model with empirical tests.

  20. Jouer du piano

    Directory of Open Access Journals (Sweden)

    Fériel Kaddour

    2011-04-01

    Full Text Available La réflexion s’appuie dans un premier temps sur une opposition entre deux attitudes de pianistes  à l’égard du travail à l’instrument : Gould, qui revendique une séparation d’avec le clavier pour ne privilégier que la lecture; Arrau, dont la technique au contraire vise à « faire corps » avec son piano. L’étude de ces deux démarches d’interprètes conduit à une conclusion croisée : l’abstraction gouldienne n’est rien d’autre qu’un déplacement du jeu vers d’autres instruments (ceux qui servent à la prise de son et au montage de ses enregistrements ; le « faire-corps » hérité de la culture pianistique romantique est plus dialectique que fusionnel, et en cela implique une capacité de mise à distance. A partir de cette double conclusion, on tâche enfin de repenser la place du jeu à l’instrument dans la mise en œuvre d’une interprétation, en interrogeant le dialogue qui s’instaure entre la partition telle qu’elle s’écrit et le geste tel qu’il se joue.Our study leans on an opposition between two pianists' attitudes about their work with the instrument. Gould claims a necessary separation from the keyboard in order to prioritize reading. Arrau, on the contrary, relies on a technique which consists in “being one” with his piano. The analysis of these two interprets’ behaviours leads to a crossed conclusion: the gouldian abstraction is nothing else than a displacement of the playing towards another kind of instruments, the ones he uses in sound recording and cut up; Arrau’s “being one” is more dialectic than at first sight, and it therefore implies a real distancing from the piano. This constatation leads to rethink the place of the piano playing in the setting of an interpretation, and to highlight the real dialogue which develops itself between the score as it has been written and the gesture as it is played.

  1. Patients' Acceptance of Smartphone Health Technology for Chronic Disease Management: A Theoretical Model and Empirical Test.

    Science.gov (United States)

    Dou, Kaili; Yu, Ping; Deng, Ning; Liu, Fang; Guan, YingPing; Li, Zhenye; Ji, Yumeng; Du, Ningkai; Lu, Xudong; Duan, Huilong

    2017-12-06

    Chronic disease patients often face multiple challenges from difficult comorbidities. Smartphone health technology can be used to help them manage their conditions only if they accept and use the technology. The aim of this study was to develop and test a theoretical model to predict and explain the factors influencing patients' acceptance of smartphone health technology for chronic disease management. Multiple theories and factors that may influence patients' acceptance of smartphone health technology have been reviewed. A hybrid theoretical model was built based on the technology acceptance model, dual-factor model, health belief model, and the factors identified from interviews that might influence patients' acceptance of smartphone health technology for chronic disease management. Data were collected from patient questionnaire surveys and computer log records about 157 hypertensive patients' actual use of a smartphone health app. The partial least square method was used to test the theoretical model. The model accounted for .412 of the variance in patients' intention to adopt the smartphone health technology. Intention to use accounted for .111 of the variance in actual use and had a significant weak relationship with the latter. Perceived ease of use was affected by patients' smartphone usage experience, relationship with doctor, and self-efficacy. Although without a significant effect on intention to use, perceived ease of use had a significant positive influence on perceived usefulness. Relationship with doctor and perceived health threat had significant positive effects on perceived usefulness, countering the negative influence of resistance to change. Perceived usefulness, perceived health threat, and resistance to change significantly predicted patients' intentions to use the technology. Age and gender had no significant influence on patients' acceptance of smartphone technology. The study also confirmed the positive relationship between intention to use

  2. Horizontal crash testing and analysis of model flatrols

    International Nuclear Information System (INIS)

    Dowler, H.J.; Soanes, T.P.T.

    1985-01-01

    To assess the behaviour of a full scale flask and flatrol during a proposed demonstration impact into a tunnel abutment, a mathematical modelling technique was developed and validated. The work was performed at quarter scale and comprised of both scale model tests and mathematical analysis in one and two dimensions. Good agreement between model test results of the 26.8m/s (60 mph) abutment impacts and the mathematical analysis, validated the modelling techniques. The modelling method may be used with confidence to predict the outcome of the proposed full scale demonstration. (author)

  3. Geometrical optics modeling of the grating-slit test.

    Science.gov (United States)

    Liang, Chao-Wen; Sasian, Jose

    2007-02-19

    A novel optical testing method termed the grating-slit test is discussed. This test uses a grating and a slit, as in the Ronchi test, but the grating-slit test is different in that the grating is used as the incoherent illuminating object instead of the spatial filter. The slit is located at the plane of the image of a sinusoidal intensity grating. An insightful geometrical-optics model for the grating-slit test is presented and the fringe contrast ratio with respect to the slit width and object-grating period is obtained. The concept of spatial bucket integration is used to obtain the fringe contrast ratio.

  4. Conducting field studies for testing pesticide leaching models

    Science.gov (United States)

    Smith, Charles N.; Parrish, Rudolph S.; Brown, David S.

    1990-01-01

    A variety of predictive models are being applied to evaluate the transport and transformation of pesticides in the environment. These include well known models such as the Pesticide Root Zone Model (PRZM), the Risk of Unsaturated-Saturated Transport and Transformation Interactions for Chemical Concentrations Model (RUSTIC) and the Groundwater Loading Effects of Agricultural Management Systems Model (GLEAMS). The potentially large impacts of using these models as tools for developing pesticide management strategies and regulatory decisions necessitates development of sound model validation protocols. This paper offers guidance on many of the theoretical and practical problems encountered in the design and implementation of field-scale model validation studies. Recommendations are provided for site selection and characterization, test compound selection, data needs, measurement techniques, statistical design considerations and sampling techniques. A strategy is provided for quantitatively testing models using field measurements.

  5. RELAP5 kinetics model development for the Advanced Test Reactor

    International Nuclear Information System (INIS)

    Judd, J.L.; Terry, W.K.

    1990-01-01

    A point-kinetics model of the Advanced Test Reactor has been developed for the RELAP5 code. Reactivity feedback parameters were calculated by a three-dimensional analysis with the PDQ neutron diffusion code. Analyses of several hypothetical reactivity insertion events by the new model and two earlier models are discussed. 3 refs., 10 figs., 6 tabs

  6. Tests of the single-pion exchange model

    International Nuclear Information System (INIS)

    Treiman, S.B.; Yang, C.N.

    1983-01-01

    The single-pion exchange model (SPEM) of high-energy particle reactions provides an attractively simple picture of seemingly complex processes and has accordingly been much discussed in recent times. The purpose of this note is to call attention to the possibility of subjecting the model to certain tests precisely in the domain where the model stands the best chance of making sense

  7. A Dutch test with the NewProd-model

    NARCIS (Netherlands)

    Bronnenberg, J.J.A.M.; van Engelen, M.L.

    1988-01-01

    The paper contains a report of a test of Cooper's NewProd model for predicting success and failure of product development projects. Based on Canadian data, the model has been shown to make predictions which are 84% correct. Having reservations on the reliability and validity of the model on

  8. Scalable Power-Component Models for Concept Testing

    Science.gov (United States)

    2011-08-17

    motor speed can be either positive or negative dependent upon the propelling or regenerative braking scenario. The simulation provides three...the machine during generation or regenerative braking . To use the model, the user modifies the motor model criteria parameters by double-clicking... SYSTEMS ENGINEERING AND TECHNOLOGY SYMPOSIUM MODELING & SIMULATION, TESTING AND VALIDATION (MSTV) MINI-SYMPOSIUM AUGUST 9-11 DEARBORN, MICHIGAN

  9. Development of dynamic Bayesian models for web application test management

    Science.gov (United States)

    Azarnova, T. V.; Polukhin, P. V.; Bondarenko, Yu V.; Kashirina, I. L.

    2018-03-01

    The mathematical apparatus of dynamic Bayesian networks is an effective and technically proven tool that can be used to model complex stochastic dynamic processes. According to the results of the research, mathematical models and methods of dynamic Bayesian networks provide a high coverage of stochastic tasks associated with error testing in multiuser software products operated in a dynamically changing environment. Formalized representation of the discrete test process as a dynamic Bayesian model allows us to organize the logical connection between individual test assets for multiple time slices. This approach gives an opportunity to present testing as a discrete process with set structural components responsible for the generation of test assets. Dynamic Bayesian network-based models allow us to combine in one management area individual units and testing components with different functionalities and a direct influence on each other in the process of comprehensive testing of various groups of computer bugs. The application of the proposed models provides an opportunity to use a consistent approach to formalize test principles and procedures, methods used to treat situational error signs, and methods used to produce analytical conclusions based on test results.

  10. Perceptions of the Impact of Online Learning as a Distance-based Learning Model on the Professional Practices of Working Nurses in Northern Ontario | Perceptions de l’impact de l’apprentissage en ligne comme modèle d’apprentissage à distance sur les pratiques professionnelles du personnel infirmier du nord de l’Ontario

    Directory of Open Access Journals (Sweden)

    Lorraine Mary Carter

    2016-08-01

    Full Text Available Nurses in Canada face diverse challenges to their ongoing educational pursuits. As a result, they have been early adopters of courses and programs based on distance education principles and, in particular, online learning models. In the study described in this paper, nurses studying at two northern universities, in programs involving online learning, were interviewed about their learning experiences and the impact of these experiences on their practice. The study led to insights into the factors affecting teaching and learning in distance settings; the complex work-life-study roles experienced by some nurses; life and work realities in northern settings; and the sustained importance of access enabled by online learning approaches. Au Canada, le personnel infirmier fait face à divers défis relatifs à l’éducation permanente. Les infirmiers et infirmières ont donc été parmi les premiers à adopter les cours et programmes appuyant les principes de l’éducation à distance et, en particulier, les modèles d’apprentissage en ligne. Dans l’étude que décrit cet article, le personnel infirmier étudiant dans deux universités du nord de l’Ontario, dans des programmes utilisant l’apprentissage en ligne, a été interviewé au sujet de ses expériences d’apprentissage et de l’incidence que celui-ci a eu sur la pratique des soins infirmiers. L’étude a permis de mieux comprendre les facteurs qui affectent l’enseignement et l’apprentissage à distance, les rôles complexes que jouent certains infirmiers et infirmières dans leur travail-vie-formation, les réalités de la vie et du travail dans les contextes nordiques et l’importance durable de l’accès que permettent les approches d’enseignement en ligne.

  11. La grammaticalisation du monde.

    Directory of Open Access Journals (Sweden)

    Etienne Pingaud

    2010-01-01

    Full Text Available Ouvrage atypique par le fond comme par la forme, Le devoir et la grâce rend compte du minutieux travail d’élaboration théorique auquel s’attelle Cyril Lemieux depuis plusieurs années. Et le résultat final se veut pour le moins ambitieux : l’auteur propose un système total supposé dépasser d’un même élan le relativisme, le mentalisme, l’universalisme ethnocentrique, l’historicisme, le naturalisme et l’herméneutisme, tout en réconciliant les sciences sociales avec le ...

  12. Le sacre du printemps

    Directory of Open Access Journals (Sweden)

    Denise Pumain

    2002-03-01

    Full Text Available Cybergeo aura six ans en avril : dans la réalité du virtuel, dans l'univers récent et fluctuant de la publication en ligne, cela fait de nous, tout à la fois, des pionniers et des vétérans. De façon plus surprenante, il se trouve que nous sommes aussi uniques : parmi toutes les revues électroniques de sciences sociales, aucune ne combine comme Cybergeo ancienneté, publication exclusivement électronique, liberté d'accès au texte intégral, édition et gestion par des chercheurs, et comité de lec...

  13. Le Brahmane du Komintern

    Directory of Open Access Journals (Sweden)

    Elizabeth Burgos

    2008-01-01

    Full Text Available Le Brahmane du Komintern, largometraje documental del realizador francés Vladimir León, constituye un ejercicio ejemplar de investigación histórica y  de lograda factura de realización. Y, pese a no haber contado con la ayuda de ninguno organismo público, se trata de un ambicioso proyecto que cubre una amplia extensión geográfica que abarca: Estados Unidos, México, Moscú, Berlín, y la India. Gira en torno a una figura que tuvo en su tiempo su hora de gloria. Un bengalí, hijo de braman, la c...

  14. (Sorghum bicolor (L.) Moench) du Nord du Burkina Faso

    African Journals Online (AJOL)

    SARAH

    29 déc. 2014 ... sorghos à grains sucrés ont un cycle court et arrivent donc à maturité avant les autres sorghos et le mil d'où leur exploitation comme aliment de soudure par les paysans. L'organisation de la diversité morphologique des accessions de sorghos à grains sucrés du Nord du. Burkina autour principalement des ...

  15. OPERATION DU FOISONNEMENT

    Directory of Open Access Journals (Sweden)

    Gholamreza Djelveh

    2010-04-01

    Full Text Available Mousses alimentaires sont un sous-ensemble des aliments connus sous le nom de produits fouettés ou des produits aérés. Ils sont des produits formulés avec des qualités telles que la légèreté et la souplesse et sont principalement consommés à l'apéritif ou au dessert. Les produits en mousse obtenue par dispersion d'un gaz dans une matrice alimentaire (la phase continue ont connu un développement croissant au cours des années 80 et 90. Le processus d'aération liés à leurs activités de production est appelée l'expansion ou à fouetter. Le document présente les principaux-paramètres du procédé du point permanent de la formulation, la mise en œuvre processus dans les installations pilotes et à l'échelle industrielle, la caractérisation des produits finis, la base énergétique de l'échelle de processus en place, et le lien entre la formulation, émulsion préparation de l'expansion. Cette vue d'ensemble de l'opération d'expansion continue, nous a permis de mettre en évidence le fait qu'il ya des opérations de l'unité encore mal décrite par le génie des procédés et pour lesquels les méthodes et outils pour l'extrapolation et la prédiction sont encore à leurs balbutiements.

  16. Alimentation du nouveau-ne et du nourrisson dans la region ...

    African Journals Online (AJOL)

    Alimentation du nouveau-ne et du nourrisson dans la region centrale du togo : pratiques familiales et communautaires avant la mise en oeuvre de la strategie « prise en charge integree des maladies de l'enfant »

  17. Using Virtual ATE Model to Migrate Test Programs

    Institute of Scientific and Technical Information of China (English)

    王晓明; 杨乔林

    1995-01-01

    Bacause of high development costs of IC (Integrated Circuit)test programs,recycling existing test programs from one kind of ATE (Automatic Test Equipment) to another or generating directly from CAD simulation modules to ATE is more and more valuable.In this paper,a new approach to migrating test programs is presented.A virtual ATE model based on object-oriented paradigm is developed;it runs Test C++ (an intermediate test control language) programs and TeIF(Test Inftermediate Format-an intermediate pattern),migrates test programs among three kinds of ATE (Ando DIC8032,Schlumberger S15 and GenRad 1732) and generates test patterns from two kinds of CAD 9Daisy and Panda) automatically.

  18. Dynamic Testing of Signal Transduction Deregulation During Breast Cancer Initiation

    Science.gov (United States)

    2012-07-01

    Std. Z39.18 Victoria Seewaldt, M.D. Dynamic Testing of Signal Transduction Deregulation During Breast Cancer Initiation Duke University Durham...attomole- zeptomole range. Internal dilution curves insure a high-dynamic calibration range. DU -26 8L DU -26 6L DU -29 5R DU -22 9.2 L DU...3: Nanobiosensor technology is translated to test for pathway deregulation in RPFNA cytology obtained from 10 high-risk women with cytological

  19. Comparing the relative cost-effectiveness of diagnostic studies: a new model

    International Nuclear Information System (INIS)

    Patton, D.D.; Woolfenden, J.M.; Wellish, K.L.

    1986-01-01

    We have developed a model to compare the relative cost-effectiveness of two or more diagnostic tests. The model defines a cost-effectiveness ratio (CER) for a diagnostic test as the ratio of effective cost to base cost, only dollar costs considered. Effective cost includes base cost, cost of dealing with expected side effects, and wastage due to imperfect test performance. Test performance is measured by diagnostic utility (DU), a measure of test outcomes incorporating the decision-analytic variables sensitivity, specificity, equivocal fraction, disease probability, and outcome utility. Each of these factors affecting DU, and hence CER, is a local, not universal, value; these local values strongly affect CER, which in effect becomes a property of the local medical setting. When DU = +1 and there are no adverse effects, CER = 1 and the patient benefits from the test dollar for dollar. When there are adverse effects effective cost exceeds base cost, and for an imperfect test DU 1. As DU approaches 0 (worthless test), CER approaches infinity (no effectiveness at any cost). If DU is negative, indicating that doing the test at all would be detrimental, CER also becomes negative. We conclude that the CER model is a useful preliminary method for ranking the relative cost-effectiveness of diagnostic tests, and that the comparisons would best be done using local values; different groups might well arrive at different rankings. (Author)

  20. On selection of optimal stochastic model for accelerated life testing

    International Nuclear Information System (INIS)

    Volf, P.; Timková, J.

    2014-01-01

    This paper deals with the problem of proper lifetime model selection in the context of statistical reliability analysis. Namely, we consider regression models describing the dependence of failure intensities on a covariate, for instance, a stressor. Testing the model fit is standardly based on the so-called martingale residuals. Their analysis has already been studied by many authors. Nevertheless, the Bayes approach to the problem, in spite of its advantages, is just developing. We shall present the Bayes procedure of estimation in several semi-parametric regression models of failure intensity. Then, our main concern is the Bayes construction of residual processes and goodness-of-fit tests based on them. The method is illustrated with both artificial and real-data examples. - Highlights: • Statistical survival and reliability analysis and Bayes approach. • Bayes semi-parametric regression modeling in Cox's and AFT models. • Bayes version of martingale residuals and goodness-of-fit test

  1. Aile adaptable : Design du systeme d'actionnement de l'aileron rigide, caracterisation des capteurs de pression et instrumentation pour des tests statiques =

    Science.gov (United States)

    Vincent, Jean-Baptiste

    This Master's thesis is part of a multidisciplinary optimisation project initiated by the Consortium for Research and Innovation in Aerospace in Quebec (CRIAQ) ; this project is about designing and manufacturing a morphing wing demonstrator. The morphing design adopted in this project is based on airfoil thickness variation applied to the upper skin. This morphing generates a change in the laminar to turbulent boundary layer transition position on top of the wing. The position of this transition area leads to significant changes in the aerodynamic performance of the wing. The study presented here focuses on the design of the conventional aileron actuation system and on the characterization of the high sensitivity differential pressure sensors installed on the upper skin in order to determine the laminar to turbulent transition position. Furthermore, the study focuses on the data acquisition system for the morphing wing structural test validation. The aileron actuation system is based on a linear actuator actuated by a brushless motor. The component choice is presented as well as the command method. A static validation as well as wind tunnel validation is presented. The pressure sensor characterization is performed by installing three of those high sensitivity differential pressure sensors in a bi-dimensional known airfoil. This study goes through the process of determining the sensor position in order to observe the transition area by using a computational fluid dynamics (CFD) statistic approach. The validation of the laminar to turbulent transition position is carried out with a series of wind tunnel tests. A structural test has been executed in order to validate the wing structure. This Master's thesis shows the data acquisition system for the microstrain measurement installed inside the morphing wing. A hardware and software architecture description is developed and presented as well as the practical results.

  2. A new fit-for-purpose model testing framework: Decision Crash Tests

    Science.gov (United States)

    Tolson, Bryan; Craig, James

    2016-04-01

    Decision-makers in water resources are often burdened with selecting appropriate multi-million dollar strategies to mitigate the impacts of climate or land use change. Unfortunately, the suitability of existing hydrologic simulation models to accurately inform decision-making is in doubt because the testing procedures used to evaluate model utility (i.e., model validation) are insufficient. For example, many authors have identified that a good standard framework for model testing called the Klemes Crash Tests (KCTs), which are the classic model validation procedures from Klemeš (1986) that Andréassian et al. (2009) rename as KCTs, have yet to become common practice in hydrology. Furthermore, Andréassian et al. (2009) claim that the progression of hydrological science requires widespread use of KCT and the development of new crash tests. Existing simulation (not forecasting) model testing procedures such as KCTs look backwards (checking for consistency between simulations and past observations) rather than forwards (explicitly assessing if the model is likely to support future decisions). We propose a fundamentally different, forward-looking, decision-oriented hydrologic model testing framework based upon the concept of fit-for-purpose model testing that we call Decision Crash Tests or DCTs. Key DCT elements are i) the model purpose (i.e., decision the model is meant to support) must be identified so that model outputs can be mapped to management decisions ii) the framework evaluates not just the selected hydrologic model but the entire suite of model-building decisions associated with model discretization, calibration etc. The framework is constructed to directly and quantitatively evaluate model suitability. The DCT framework is applied to a model building case study on the Grand River in Ontario, Canada. A hypothetical binary decision scenario is analysed (upgrade or not upgrade the existing flood control structure) under two different sets of model building

  3. Magnetic Testing, and Modeling, Simulation and Analysis for Space Applications

    Science.gov (United States)

    Boghosian, Mary; Narvaez, Pablo; Herman, Ray

    2012-01-01

    The Aerospace Corporation (Aerospace) and Lockheed Martin Space Systems (LMSS) participated with Jet Propulsion Laboratory (JPL) in the implementation of a magnetic cleanliness program of the NASA/JPL JUNO mission. The magnetic cleanliness program was applied from early flight system development up through system level environmental testing. The JUNO magnetic cleanliness program required setting-up a specialized magnetic test facility at Lockheed Martin Space Systems for testing the flight system and a testing program with facility for testing system parts and subsystems at JPL. The magnetic modeling, simulation and analysis capability was set up and performed by Aerospace to provide qualitative and quantitative magnetic assessments of the magnetic parts, components, and subsystems prior to or in lieu of magnetic tests. Because of the sensitive nature of the fields and particles scientific measurements being conducted by the JUNO space mission to Jupiter, the imposition of stringent magnetic control specifications required a magnetic control program to ensure that the spacecraft's science magnetometers and plasma wave search coil were not magnetically contaminated by flight system magnetic interferences. With Aerospace's magnetic modeling, simulation and analysis and JPL's system modeling and testing approach, and LMSS's test support, the project achieved a cost effective approach to achieving a magnetically clean spacecraft. This paper presents lessons learned from the JUNO magnetic testing approach and Aerospace's modeling, simulation and analysis activities used to solve problems such as remnant magnetization, performance of hard and soft magnetic materials within the targeted space system in applied external magnetic fields.

  4. Deformation modeling and the strain transient dip test

    International Nuclear Information System (INIS)

    Jones, W.B.; Rohde, R.W.; Swearengen, J.C.

    1980-01-01

    Recent efforts in material deformation modeling reveal a trend toward unifying creep and plasticity with a single rate-dependent formulation. While such models can describe actual material deformation, most require a number of different experiments to generate model parameter information. Recently, however, a new model has been proposed in which most of the requisite constants may be found by examining creep transients brought about through abrupt changes in creep stress (strain transient dip test). The critical measurement in this test is the absence of a resolvable creep rate after a stress drop. As a consequence, the result is extraordinarily sensitive to strain resolution as well as machine mechanical response. This paper presents the design of a machine in which these spurious effects have been minimized and discusses the nature of the strain transient dip test using the example of aluminum. It is concluded that the strain transient dip test is not useful as the primary test for verifying any micromechanical model of deformation. Nevertheless, if a model can be developed which is verifiable by other experimentts, data from a dip test machine may be used to generate model parameters

  5. Allele-sharing models: LOD scores and accurate linkage tests.

    Science.gov (United States)

    Kong, A; Cox, N J

    1997-11-01

    Starting with a test statistic for linkage analysis based on allele sharing, we propose an associated one-parameter model. Under general missing-data patterns, this model allows exact calculation of likelihood ratios and LOD scores and has been implemented by a simple modification of existing software. Most important, accurate linkage tests can be performed. Using an example, we show that some previously suggested approaches to handling less than perfectly informative data can be unacceptably conservative. Situations in which this model may not perform well are discussed, and an alternative model that requires additional computations is suggested.

  6. An Innovative Physical Model for Testing Bucket Foundations

    DEFF Research Database (Denmark)

    Foglia, Aligi; Ibsen, Lars Bo; Andersen, Lars Vabbersgaard

    2012-01-01

    Pa), 20 (kPa), and 30 (kPa) respectively. The comparison between the tests conducted at stress level of 0 (kPa), and the tests with stress level increased, shows remarkable differences. The relationship between scaled overturning moment and rotation is well represented by a power law. The exponent...... of the power law is consistent among all tests carried out with stress level increased. Besides, attention is given to the instantaneous centre of rotation distribution. To validate the mode, the tests are compared with a large scale test by means of a scaling moment. The validation of the model is only...

  7. Testing and Modeling of Machine Properties in Resistance Welding

    DEFF Research Database (Denmark)

    Wu, Pei

    The objective of this work has been to test and model the machine properties including the mechanical properties and the electrical properties in resistance welding. The results are used to simulate the welding process more accurately. The state of the art in testing and modeling machine properties...... as real projection welding tests, is easy to realize in industry, since tests may be performed in situ. In part II, an approach of characterizing the electrical properties of AC resistance welding machines is presented, involving testing and mathematical modelling of the weld current, the firing angle...... in resistance welding has been described based on a comprehensive literature study. The present thesis has been subdivided into two parts: Part I: Mechanical properties of resistance welding machines. Part II: Electrical properties of resistance welding machines. In part I, the electrode force in the squeeze...

  8. THE MISHKIN TEST: AN ANALYSIS OF MODEL EXTENSIONS

    Directory of Open Access Journals (Sweden)

    Diana MURESAN

    2015-04-01

    Full Text Available This paper reviews empirical research that apply Mishkin test for the examination of the existence of accruals anomaly using alternative approaches. Mishkin test is a test used in macro-econometrics for rational hypothesis, which test for the market efficiency. Starting with Sloan (1996 the model has been applied to accruals anomaly literature. Since Sloan (1996, the model has known various improvements and it has been the subject to many debates in the literature regarding its efficacy. Nevertheless, the current evidence strengthens the pervasiveness of the model. The analyses realized on the extended studies on Mishkin test highlights that adding additional variables enhances the results, providing insightful information about the occurrence of accruals anomaly.

  9. Test beam results on Atlas electromagnetic end-cap calorimeter: Electrons-jets separation; Resultats des tests en faisceau sur les bouchons du calorimetre electromagnetique d'ATLAS - separation electrons-jets

    Energy Technology Data Exchange (ETDEWEB)

    Serfon, C

    2005-05-15

    ATLAS is one of the four experiments being built on the future proton-proton collider at CERN: the LHC. This experiment has a large physics program, from Standard Model to new physics. The search for the Higgs boson in two photons or in four leptons, or the search of Z' or W' needs a good energy resolution for the electromagnetic calorimeter. This thesis describes the beam tests performed on three modules of the electromagnetic end cap calorimeter. A 0.6% non-uniformity, and a 0.7% energy resolution global constant term (dominant at high energy) has been obtained. Moreover, a study on the separation between electrons and jets is also performed. This study shows that a jets rejection factor of 10{sup 5} can be obtained keeping an electron efficiency better than 78%. (author)

  10. Functional Testing Protocols for Commercial Building Efficiency Baseline Modeling Software

    Energy Technology Data Exchange (ETDEWEB)

    Jump, David; Price, Phillip N.; Granderson, Jessica; Sohn, Michael

    2013-09-06

    This document describes procedures for testing and validating proprietary baseline energy modeling software accuracy in predicting energy use over the period of interest, such as a month or a year. The procedures are designed according to the methodology used for public domain baselining software in another LBNL report that was (like the present report) prepared for Pacific Gas and Electric Company: ?Commercial Building Energy Baseline Modeling Software: Performance Metrics and Method Testing with Open Source Models and Implications for Proprietary Software Testing Protocols? (referred to here as the ?Model Analysis Report?). The test procedure focuses on the quality of the software?s predictions rather than on the specific algorithms used to predict energy use. In this way the software vendor is not required to divulge or share proprietary information about how their software works, while enabling stakeholders to assess its performance.

  11. Calibration of a Chemistry Test Using the Rasch Model

    Directory of Open Access Journals (Sweden)

    Nancy Coromoto Martín Guaregua

    2011-11-01

    Full Text Available The Rasch model was used to calibrate a general chemistry test for the purpose of analyzing the advantages and information the model provides. The sample was composed of 219 college freshmen. Of the 12 questions used, good fit was achieved in 10. The evaluation shows that although there are items of variable difficulty, there are gaps on the scale; in order to make the test complete, it will be necessary to design new items to fill in these gaps.

  12. Latent Trait Model Contributions to Criterion-Referenced Testing Technology.

    Science.gov (United States)

    1982-02-01

    levels of ability (ranging from very low to very high). The steps in the reserach were as follows: 1. Specify the characteristics of a "typical" pool...conventional testing methodologies displayed good fit to both of the latent trait models. The one-parameter model compared favorably with the three- parameter... Methodological developments: New directions for testing a!nd measurement (No. 4). San Francisco: Jossey-Bass, 1979. Haubleton, R. K. Advances in

  13. Instrumentation and testing of a prestressed concrete containment vessel model

    International Nuclear Information System (INIS)

    Hessheimer, M.F.; Pace, D.W.; Klamerus, E.W.

    1997-01-01

    Static overpressurization tests of two scale models of nuclear containment structures - a steel containment vessel (SCV) representative of an improved, boiling water reactor (BWR) Mark II design and a prestressed concrete containment vessel (PCCV) for pressurized water reactors (PWR) - are being conducted by Sandia National Laboratories for the Nuclear Power Engineering Corporation of Japan and the U.S. Nuclear Regulatory Commission. This paper discusses plans for instrumentation and testing of the PCCV model. 6 refs., 2 figs., 2 tabs

  14. Modeling of creep-fatigue interaction of zirconium {alpha} under cyclic loading at 200 C; Modelisation du comportement et de l`endommagement en fatigue-fluage du zirconium {alpha} a 200C

    Energy Technology Data Exchange (ETDEWEB)

    Vogel, C.

    1996-04-01

    The present work deals with mechanical behaviour of zirconium alpha at 200 deg. C and crack initiation prediction methods, particularly when loading conditions lead to interaction of fatigue and creep phenomena. A classical approach used to study interaction between cyclic effects and constant loading effects does not give easy understanding of experimental results. Therefore, a new approach has been developed, which allow to determine a number of cycles for crack initiation for complex structures under large loading conditions. To study influence of fatigue and creep interaction on crack initiation, a model was chosen, using a scalar variable, giving representation of the material deterioration state. The model uses a non linear cumulating effect between the damage corresponding to cyclic loads and the damage correlated to time influence. The model belongs to uncoupled approaches between damage and behaviour, which is described here by a two inelastic deformations model. This mechanical behaviour model is chosen because it allows distinction between a plastic and a viscous part in inelastic flow. Cyclic damage is function of stress amplitude and mean stress. For the peculiar sensitivity of the material to creep, a special parameter bas been defined to be critical toward creep damage. It is the kinematic term associated to state variables describing this type of hardening in the viscous mechanism. (author).

  15. Testing the Structure of Hydrological Models using Genetic Programming

    Science.gov (United States)

    Selle, B.; Muttil, N.

    2009-04-01

    Genetic Programming is able to systematically explore many alternative model structures of different complexity from available input and response data. We hypothesised that genetic programming can be used to test the structure hydrological models and to identify dominant processes in hydrological systems. To test this, genetic programming was used to analyse a data set from a lysimeter experiment in southeastern Australia. The lysimeter experiment was conducted to quantify the deep percolation response under surface irrigated pasture to different soil types, water table depths and water ponding times during surface irrigation. Using genetic programming, a simple model of deep percolation was consistently evolved in multiple model runs. This simple and interpretable model confirmed the dominant process contributing to deep percolation represented in a conceptual model that was published earlier. Thus, this study shows that genetic programming can be used to evaluate the structure of hydrological models and to gain insight about the dominant processes in hydrological systems.

  16. Improved animal models for testing gene therapy for atherosclerosis.

    Science.gov (United States)

    Du, Liang; Zhang, Jingwan; De Meyer, Guido R Y; Flynn, Rowan; Dichek, David A

    2014-04-01

    Gene therapy delivered to the blood vessel wall could augment current therapies for atherosclerosis, including systemic drug therapy and stenting. However, identification of clinically useful vectors and effective therapeutic transgenes remains at the preclinical stage. Identification of effective vectors and transgenes would be accelerated by availability of animal models that allow practical and expeditious testing of vessel-wall-directed gene therapy. Such models would include humanlike lesions that develop rapidly in vessels that are amenable to efficient gene delivery. Moreover, because human atherosclerosis develops in normal vessels, gene therapy that prevents atherosclerosis is most logically tested in relatively normal arteries. Similarly, gene therapy that causes atherosclerosis regression requires gene delivery to an existing lesion. Here we report development of three new rabbit models for testing vessel-wall-directed gene therapy that either prevents or reverses atherosclerosis. Carotid artery intimal lesions in these new models develop within 2-7 months after initiation of a high-fat diet and are 20-80 times larger than lesions in a model we described previously. Individual models allow generation of lesions that are relatively rich in either macrophages or smooth muscle cells, permitting testing of gene therapy strategies targeted at either cell type. Two of the models include gene delivery to essentially normal arteries and will be useful for identifying strategies that prevent lesion development. The third model generates lesions rapidly in vector-naïve animals and can be used for testing gene therapy that promotes lesion regression. These models are optimized for testing helper-dependent adenovirus (HDAd)-mediated gene therapy; however, they could be easily adapted for testing of other vectors or of different types of molecular therapies, delivered directly to the blood vessel wall. Our data also supports the promise of HDAd to deliver long

  17. A general diagnostic model applied to language testing data.

    Science.gov (United States)

    von Davier, Matthias

    2008-11-01

    Probabilistic models with one or more latent variables are designed to report on a corresponding number of skills or cognitive attributes. Multidimensional skill profiles offer additional information beyond what a single test score can provide, if the reported skills can be identified and distinguished reliably. Many recent approaches to skill profile models are limited to dichotomous data and have made use of computationally intensive estimation methods such as Markov chain Monte Carlo, since standard maximum likelihood (ML) estimation techniques were deemed infeasible. This paper presents a general diagnostic model (GDM) that can be estimated with standard ML techniques and applies to polytomous response variables as well as to skills with two or more proficiency levels. The paper uses one member of a larger class of diagnostic models, a compensatory diagnostic model for dichotomous and partial credit data. Many well-known models, such as univariate and multivariate versions of the Rasch model and the two-parameter logistic item response theory model, the generalized partial credit model, as well as a variety of skill profile models, are special cases of this GDM. In addition to an introduction to this model, the paper presents a parameter recovery study using simulated data and an application to real data from the field test for TOEFL Internet-based testing.

  18. Application of remote sensing for analyzing climatic variation in the boreal and subarctic regions of Canada and for validating the Canadian Regional Climate Model; Application de la teledetection a l'analyse de la variabilite climatique des regions boreales et subarctiques du Canada et a la validation du modele regional canadien du climat

    Energy Technology Data Exchange (ETDEWEB)

    Fillol, E.J.

    2003-07-01

    This study examined climate variations over the past few decades as well as the tools used to model future climate. The study included an interpretation of the National Oceanic and Atmospheric Administration Advanced Very High Resolution Radiometer (NOAA-AVHRR) time series data at the continental spatial scale. Data collected over a period of two decades was used to study and monitor Canada's boreal ecosystem activity and to observe recent climatic change. The study involved the use of classical parameters associated with remote sensing in the visible and thermal infrared spectra for vegetation activity and land-surface temperatures. Problems associated with instrumental drift and inter-satellite adjustment were minimized by choosing indicators for the length of the growing season, annual growing degree-days and ecotone displacement. Climate variations over the past twenty years were compared with daily meteorological data of temperature, precipitation and snow cover. Rapid cycle climatic phenomena such as the El Nino and La Nina appear to have influenced the central region of Canada. The North Atlantic Oscillation and Arctic Oscillation also influenced the climate regime of Canada and annual growing degree-days. Indicators for vegetation activity and land-surface temperature suggest that a North-South disparity exists over Canada. A warming trend with an increased growing season was observed for the region north of the 55 parallel, while southern regions appear to be cooling. This study also used remote sensing to validate the Canadian Regional Climate Model (CRCM) through a comparison of ground temperature values modelled by the CRCM with composite satellite temperatures. The results indicate a small under-estimation of the CRCM ground temperature during the summer due to an overestimation of the precipitation rate. It was concluded that climate models such as the CRCM are useful in making reliable predictions of future climate trends.

  19. Numerical Modelling and Measurement in a Test Secondary Settling Tank

    DEFF Research Database (Denmark)

    Dahl, C.; Larsen, Torben; Petersen, O.

    1994-01-01

    sludge. Phenomena as free and hindered settling and the Bingham plastic characteristic of activated sludge suspensions are included in the numerical model. Further characterisation and test tank experiments are described. The characterisation experiments were designed to measure calibration parameters...... for model description of settling and density differences. In the test tank experiments, flow velocities and suspended sludge concentrations were measured with different tank inlet geomotry and hydraulic and sludge loads. The test tank experiments provided results for the calibration of the numerical model......A numerical model and measurements of flow and settling in activated sludge suspension is presented. The numerical model is an attempt to describe the complex and interrelated hydraulic and sedimentation phenomena by describing the turbulent flow field and the transport/dispersion of suspended...

  20. A tutorial on testing the race model inequality

    DEFF Research Database (Denmark)

    Gondan, Matthias; Minakata, Katsumi

    2016-01-01

    , to faster responses to redundant signals. In contrast, coactivation models assume integrated processing of the combined stimuli. To distinguish between these two accounts, Miller (1982) derived the well-known race model inequality, which has become a routine test for behavioral data in experiments...... with redundant signals. In this tutorial, we review the basic properties of redundant signals experiments and current statistical procedures used to test the race model inequality during the period between 2011 and 2014. We highlight and discuss several issues concerning study design and the test of the race...... model inequality, such as inappropriate control of Type I error, insufficient statistical power, wrong treatment of omitted responses or anticipations and the interpretation of violations of the race model inequality. We make detailed recommendations on the design of redundant signals experiments...

  1. Model tests on overall forces on the SSG pilot plant

    DEFF Research Database (Denmark)

    Margheritini, Lucia; Morris, Alex

    . The tests have been realized at the Department of civil Engineering, AAU, in the 3D deep water tank with a scale model 1:60 to prototype and a reproduced bathymetry of the selected location at the time of the experiments. Overall forces and moments have been measured during the tests. The results are given...

  2. Design Of Computer Based Test Using The Unified Modeling Language

    Science.gov (United States)

    Tedyyana, Agus; Danuri; Lidyawati

    2017-12-01

    The Admission selection of Politeknik Negeri Bengkalis through interest and talent search (PMDK), Joint Selection of admission test for state Polytechnics (SB-UMPN) and Independent (UM-Polbeng) were conducted by using paper-based Test (PBT). Paper Based Test model has some weaknesses. They are wasting too much paper, the leaking of the questios to the public, and data manipulation of the test result. This reasearch was Aimed to create a Computer-based Test (CBT) models by using Unified Modeling Language (UML) the which consists of Use Case diagrams, Activity diagram and sequence diagrams. During the designing process of the application, it is important to pay attention on the process of giving the password for the test questions before they were shown through encryption and description process. RSA cryptography algorithm was used in this process. Then, the questions shown in the questions banks were randomized by using the Fisher-Yates Shuffle method. The network architecture used in Computer Based test application was a client-server network models and Local Area Network (LAN). The result of the design was the Computer Based Test application for admission to the selection of Politeknik Negeri Bengkalis.

  3. Automated model-based testing of hybrid systems

    NARCIS (Netherlands)

    Osch, van M.P.W.J.

    2009-01-01

    In automated model-based input-output conformance testing, tests are automati- cally generated from a speci¯cation and automatically executed on an implemen- tation. Input is applied to the implementation and output is observed from the implementation. If the observed output is allowed according to

  4. Linearity and Misspecification Tests for Vector Smooth Transition Regression Models

    DEFF Research Database (Denmark)

    Teräsvirta, Timo; Yang, Yukai

    The purpose of the paper is to derive Lagrange multiplier and Lagrange multiplier type specification and misspecification tests for vector smooth transition regression models. We report results from simulation studies in which the size and power properties of the proposed asymptotic tests in small...

  5. An integrated service excellence model for military test and ...

    African Journals Online (AJOL)

    The purpose of this article is to introduce an Integrated Service Excellence Model (ISEM) for empowering the leadership core of the capital-intensive military test and evaluation facilities to provide strategic military test and evaluation services and to continuously improve service excellence by ensuring that all activities ...

  6. Towards model-based testing of electronic funds transfer systems

    NARCIS (Netherlands)

    Asaadi, H.R.; Khosravi, R.; Mousavi, M.R.; Noroozi, N.; Arbab, F.; Sirjani, M.

    2012-01-01

    We report on our first experience with applying model-based testing techniques to an operational Electronic Funds Transfer (EFT) switch. The goal is to test the conformance of the EFT switch to the standard flows described by the ISO 8583 standard. To this end, we first make a formalization of the

  7. Towards model-based testing of electronic funds transfer systems

    NARCIS (Netherlands)

    Asaadi, H.R.; Khosravi, R.; Mousavi, M.R.; Noroozi, N.

    2010-01-01

    We report on our first experience with applying model-based testing techniques to an operational Electronic Funds Transfer (EFT) switch. The goal is to test the conformance of the EFT switch to the standard flows described by the ISO 8583 standard. To this end, we first make a formalization of the

  8. A permutation test for the race model inequality

    DEFF Research Database (Denmark)

    Gondan, Matthias

    2010-01-01

    signals. Several statistical procedures have been used for testing the race model inequality. However, the commonly employed procedure does not control the Type I error. In this article a permutation test is described that keeps the Type I error at the desired level. Simulations show that the power...

  9. Testing for time-varying loadings in dynamic factor models

    DEFF Research Database (Denmark)

    Mikkelsen, Jakob Guldbæk

    Abstract: In this paper we develop a test for time-varying factor loadings in factor models. The test is simple to compute and is constructed from estimated factors and residuals using the principal components estimator. The hypothesis is tested by regressing the squared residuals on the squared...... there is evidence of time-varying loadings on the risk factors underlying portfolio returns for around 80% of the portfolios....

  10. Model-Driven Test Generation of Distributed Systems

    Science.gov (United States)

    Easwaran, Arvind; Hall, Brendan; Schweiker, Kevin

    2012-01-01

    This report describes a novel test generation technique for distributed systems. Utilizing formal models and formal verification tools, spe cifically the Symbolic Analysis Laboratory (SAL) tool-suite from SRI, we present techniques to generate concurrent test vectors for distrib uted systems. These are initially explored within an informal test validation context and later extended to achieve full MC/DC coverage of the TTEthernet protocol operating within a system-centric context.

  11. The microelectronics and photonics test bed (MPTB) space, ground test and modeling experiments

    International Nuclear Information System (INIS)

    Campbell, A.

    1999-01-01

    This paper is an overview of the MPTB (microelectronics and photonics test bed) experiment, a combination of a space experiment, ground test and modeling programs looking at the response of advanced electronic and photonic technologies to the natural radiation environment of space. (author)

  12. L’esprit du droit : modèle russe contre modèle français Sense of law : Russian model versus French model

    Directory of Open Access Journals (Sweden)

    Chantal Kourilsky-Augeven

    2009-06-01

    Full Text Available Un stéréotype récurrent dans la littérature russe distingue entre un « esprit » ou « sens du droit » qui serait propre à la culture française et un « sens de la justice » qui serait propre à la culture russe. Cette distinction s’appliquerait au premier chef à une religion catholique qualifiée de juridique en ce qu’elle serait comptable des péchés et une religion orthodoxe davantage fondée sur l’amour. Mais le modèle traditionnel russe pris en compte par la littérature, l’histoire et l’anthropologie ne saurait être statique. Deux enquêtes menées auprès de populations d’adolescents et d’adultes en 1993 et 2000 montrent comment le modèle russe fondé sur la justice et la morale se juridicise et en arrive à rejoindre le modèle français sur plusieurs points.A recurring stereotype in Russian literature opposes a « sense of law » inherent to French culture to a « sense of justice » inherent to Russian culture.This distinction is first and foremost applied to a catholic religion qualified as legalistic due to a strict accounting of sins and an orthodox religion essentially based on love. But the traditional Russian model described by literature, history and anthropology is anything but static. Two research projects carried out among an adolescent and adult population sample in 1993 and 2000 show how a Russian model based on justice and morals is being judiciarized and is increasingly moving towards the French model on several accounts.

  13. Testing and reference model analysis of FTTH system

    Science.gov (United States)

    Feng, Xiancheng; Cui, Wanlong; Chen, Ying

    2009-08-01

    With rapid development of Internet and broadband access network, the technologies of xDSL, FTTx+LAN , WLAN have more applications, new network service emerges in endless stream, especially the increase of network game, meeting TV, video on demand, etc. FTTH supports all present and future service with enormous bandwidth, including traditional telecommunication service, traditional data service and traditional TV service, and the future digital TV and VOD. With huge bandwidth of FTTH, it wins the final solution of broadband network, becomes the final goal of development of optical access network.. Fiber to the Home (FTTH) will be the goal of telecommunications cable broadband access. In accordance with the development trend of telecommunication services, to enhance the capacity of integrated access network, to achieve triple-play (voice, data, image), based on the existing optical Fiber to the curb (FTTC), Fiber To The Zone (FTTZ), Fiber to the Building (FTTB) user optical cable network, the optical fiber can extend to the FTTH system of end-user by using EPON technology. The article first introduced the basic components of FTTH system; and then explain the reference model and reference point for testing of the FTTH system; Finally, by testing connection diagram, the testing process, expected results, primarily analyze SNI Interface Testing, PON interface testing, Ethernet performance testing, UNI interface testing, Ethernet functional testing, PON functional testing, equipment functional testing, telephone functional testing, operational support capability testing and so on testing of FTTH system. ...

  14. Le plurilinguisme du perroquet

    Directory of Open Access Journals (Sweden)

    Manuel Mühlbacher

    2012-05-01

    Full Text Available La figure du perroquet occupe une position ambiguë face à la question de la traduction. Il est capable d’imiter des paroles en toutes les langues, mais il n’est capable d’en comprendre aucune — il ne peut que répéter des sons, c’est-à-dire des signifiants. Le traducteur semble faire le contraire quand il passe d’une langue à une autre en tâchant de transmettre une signification semblable par d’autres signes. L’article vise à discuter le rôle du traducteur et sa relation, éventuellement équivoque, au perroquet, en analysant la traduction allemande de Trois Contes par André Stoll et Cora van Kleffens. Un décalage au niveau sémantique peut éclairer l’interprétation du texte, par exemple en explicitant des allusions sous-jacentes, tandis que le transfert de la syntaxe française en allemand pose souvent des problèmes considérables. Comment le traducteur peut-il reproduire des structures syntaxiques qui n’existent pas en allemand, mais qui ne cessent de revenir dans le texte français ? Que faire si le texte se met à jouer au perroquet et finit par se singer lui-même ? André Stoll et Cora van Kleffens ont su trouver des stratégies pour affronter ces difficultés.The figure of the parrot holds an ambiguous position towards the question of translation. It is able to imitate all languages, but it will never understand any of them – its only skill is to mimic sounds, i.e. mere signifiers. On the contrary, the translator seems to be the antithesis of the parrot when he moves from one language to another. He endeavours to convey a similar meaning, but by different signs. The article aims at discussing the role of the translator and his or her eventually equivocal relation to the parrot by means of analysing the German translation of Trois Contes by André Stoll and Cora van Kleffens. Whereas a semantic divergence can result in a different tendency on the level of interpretation, as in the case of an underlying

  15. Study of the two-dimensional Hubbard model at half-filling through constructive methods; Etude du modele de Hubbard bidimensionnel a demi remplissage par des methodes constructives

    Energy Technology Data Exchange (ETDEWEB)

    Afchain, St

    2005-02-15

    The Hubbard model is the simplest model to describe the behaviour of fermions on a network, it takes into account only fermion scattering and only interactions with other fermions located on the same site. Half-filling means that the total number of fermions is equal to half the number of sites. In the first chapter we show how we can pass trough successive approximations from a very general Hamiltonian to the Hubbard Hamiltonian. The second chapter is dedicated to the passage from the Hamiltonian formalism to the Grassmanian functional formalism. The main idea is to show that the correlation functions of the Hamiltonian approach can be described through fermionic functional integrals which implies the possibility of speaking of the model in terms of field theory. The chapter 3 deals with the main constructive techniques that allow the strict and consistent construction of models inside the frame of field theory. We show by proving the violation of a condition concerning self-energy, that the two-dimensional Hubbard model at half-filling has not the behaviour of a Fermi liquid in the Landau's interpretation. (A.C.)

  16. Évolution des marchés du travail au Bangladesh - interaction entre ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Le Bangladesh, dont l'économie et la population sont en croissance, a surtout réussi à créer des emplois dans les industries du textile et du vêtement. ... Le South Asian Network on Economic Modeling, situé à Dhaka, réalisera le projet de ...

  17. Estrogen receptor testing and 10-year mortality from breast cancer: A model for determining testing strategy

    Directory of Open Access Journals (Sweden)

    Christopher Naugler

    2012-01-01

    Full Text Available Background: The use of adjuvant tamoxifen therapy in the treatment of estrogen receptor (ER expressing breast carcinomas represents a major advance in personalized cancer treatment. Because there is no benefit (and indeed there is increased morbidity and mortality associated with the use of tamoxifen therapy in ER-negative breast cancer, its use is restricted to women with ER expressing cancers. However, correctly classifying cancers as ER positive or negative has been challenging given the high reported false negative test rates for ER expression in surgical specimens. In this paper I model practice recommendations using published information from clinical trials to address the question of whether there is a false negative test rate above which it is more efficacious to forgo ER testing and instead treat all patients with tamoxifen regardless of ER test results. Methods: I used data from randomized clinical trials to model two different hypothetical treatment strategies: (1 the current strategy of treating only ER positive women with tamoxifen and (2 an alternative strategy where all women are treated with tamoxifen regardless of ER test results. The variables used in the model are literature-derived survival rates of the different combinations of ER positivity and treatment with tamoxifen, varying true ER positivity rates and varying false negative ER testing rates. The outcome variable was hypothetical 10-year survival. Results: The model predicted that there will be a range of true ER rates and false negative test rates above which it would be more efficacious to treat all women with breast cancer with tamoxifen and forgo ER testing. This situation occurred with high true positive ER rates and false negative ER test rates in the range of 20-30%. Conclusions: It is hoped that this model will provide an example of the potential importance of diagnostic error on clinical outcomes and furthermore will give an example of how the effect of that

  18. Testing Consent Order for Sodium Cyanide

    Science.gov (United States)

    This document announces that EPA has signed an enforceable testing Consent Order with E.I. du Pont de Nemours and Company (DuPont), FMC Corporation (FMC), Degussa Corporation (Degussa), ICI Americas Incorporated (ICI), and Cyanco Company (Cyanco).

  19. Etat Du Magnesium Dans Quelques Sols Sales Du Sud Et Du ...

    African Journals Online (AJOL)

    étude a été réalisée sur 86 échantillons de sols provenant du Centre et du Sud de l´Irak. L\\'expérimentation a consisté, d´une part, à calculer les différents sels dominants dans les sols salés par la méthode de combinaison hypothétique et, ...

  20. Caractérisation des sables et morphologie du fond du lac du ...

    African Journals Online (AJOL)

    Une analyse sédimentologique et minéralogique réalisée sur un cycle hydrologique entre octobre 2004 et août 2005 a permis d\\'évaluer les charges solides en suspension et de caractériser les sédiments du lac du barrage de Taabo. La concentration moyenne en matières en suspension (12 mg.L-1) et la turbidité ...

  1. Caractérisation des sables et morphologie du fond du lac du ...

    African Journals Online (AJOL)

    Administrateur

    Une analyse sédimentologique et minéralogique réalisée sur un cycle hydrologique entre octobre 2004 et août 2005 a permis d'évaluer les charges solides en suspension et de caractériser les sédiments du lac du barrage de Taabo. La concentration moyenne en matières en suspension (12 mg.L-1) et la turbidité ...

  2. Towards model-based testing of electronic funds transfer systems

    OpenAIRE

    Asaadi, H.R.; Khosravi, R.; Mousavi, M.R.; Noroozi, N.

    2010-01-01

    We report on our first experience with applying model-based testing techniques to an operational Electronic Funds Transfer (EFT) switch. The goal is to test the conformance of the EFT switch to the standard flows described by the ISO 8583 standard. To this end, we first make a formalization of the transaction flows specified in the ISO 8583 standard in terms of a Labeled Transition System (LTS). This formalization paves the way for model-based testing based on the formal notion of Input-Outpu...

  3. Modelling, simulation and visualisation for electromagnetic non-destructive testing

    International Nuclear Information System (INIS)

    Ilham Mukriz Zainal Abidin; Abdul Razak Hamzah

    2010-01-01

    This paper reviews the state-of-the art and the recent development of modelling, simulation and visualization for eddy current Non-Destructive Testing (NDT) technique. Simulation and visualization has aid in the design and development of electromagnetic sensors and imaging techniques and systems for Electromagnetic Non-Destructive Testing (ENDT); feature extraction and inverse problems for Quantitative Non-Destructive Testing (QNDT). After reviewing the state-of-the art of electromagnetic modelling and simulation, case studies of Research and Development in eddy current NDT technique via magnetic field mapping and thermography for eddy current distribution are discussed. (author)

  4. Data Modeling for Measurements in the Metrology and Testing Fields

    CERN Document Server

    Pavese, Franco

    2009-01-01

    Offers a comprehensive set of modeling methods for data and uncertainty analysis. This work develops methods and computational tools to address general models that arise in practice, allowing for a more valid treatment of calibration and test data and providing an understanding of complex situations in measurement science

  5. A Preliminary Field Test of an Employee Work Passion Model

    Science.gov (United States)

    Zigarmi, Drea; Nimon, Kim; Houson, Dobie; Witt, David; Diehl, Jim

    2011-01-01

    Four dimensions of a process model for the formulation of employee work passion, derived from Zigarmi, Nimon, Houson, Witt, and Diehl (2009), were tested in a field setting. A total of 447 employees completed questionnaires that assessed the internal elements of the model in a corporate work environment. Data from the measurements of work affect,…

  6. Testing Affine Term Structure Models in Case of Transaction Costs

    NARCIS (Netherlands)

    Driessen, J.J.A.G.; Melenberg, B.; Nijman, T.E.

    1999-01-01

    In this paper we empirically analyze the impact of transaction costs on the performance of affine interest rate models. We test the implied (no arbitrage) Euler restrictions, and we calculate the specification error bound of Hansen and Jagannathan to measure the extent to which a model is

  7. Testing static tradeoff theiry against pecking order models of capital ...

    African Journals Online (AJOL)

    We test two models with the purpose of finding the best empirical explanation for corporate financing choice of a cross section of 27 Nigerian quoted companies. The models were developed to represent the Static tradeoff Theory and the Pecking order Theory of capital structure with a view to make comparison between ...

  8. MODEL TESTING OF LOW PRESSURE HYDRAULIC TURBINE WITH HIGHER EFFICIENCY

    Directory of Open Access Journals (Sweden)

    V. K. Nedbalsky

    2007-01-01

    Full Text Available A design of low pressure turbine has been developed and it is covered by an invention patent and a useful model patent. Testing of the hydraulic turbine model has been carried out when it was installed on a vertical shaft. The efficiency was equal to 76–78 % that exceeds efficiency of the known low pressure blade turbines. 

  9. Direct cointegration testing in error-correction models

    NARCIS (Netherlands)

    F.R. Kleibergen (Frank); H.K. van Dijk (Herman)

    1994-01-01

    textabstractAbstract An error correction model is specified having only exact identified parameters, some of which reflect a possible departure from a cointegration model. Wald, likelihood ratio, and Lagrange multiplier statistics are derived to test for the significance of these parameters. The

  10. Animal models for testing anti-prion drugs.

    Science.gov (United States)

    Fernández-Borges, Natalia; Elezgarai, Saioa R; Eraña, Hasier; Castilla, Joaquín

    2013-01-01

    Prion diseases belong to a group of fatal infectious diseases with no effective therapies available. Throughout the last 35 years, less than 50 different drugs have been tested in different experimental animal models without hopeful results. An important limitation when searching for new drugs is the existence of appropriate models of the disease. The three different possible origins of prion diseases require the existence of different animal models for testing anti-prion compounds. Wild type, over-expressing transgenic mice and other more sophisticated animal models have been used to evaluate a diversity of compounds which some of them were previously tested in different in vitro experimental models. The complexity of prion diseases will require more pre-screening studies, reliable sporadic (or spontaneous) animal models and accurate chemical modifications of the selected compounds before having an effective therapy against human prion diseases. This review is intended to put on display the more relevant animal models that have been used in the search of new antiprion therapies and describe some possible procedures when handling chemical compounds presumed to have anti-prion activity prior to testing them in animal models.

  11. An Empirical Test of a Model of Resistance to Persuasion.

    Science.gov (United States)

    And Others; Burgoon, Michael

    1978-01-01

    Tests a model of resistance to persuasion based upon variables not considered by earlier congruity and inoculation models. Supports the prediction that the kind of critical response set induced and the target of the criticism are mediators of resistance to persuasion. (JMF)

  12. Testing and inference in nonlinear cointegrating vector error correction models

    DEFF Research Database (Denmark)

    Kristensen, D.; Rahbek, A.

    2013-01-01

    We analyze estimators and tests for a general class of vector error correction models that allows for asymmetric and nonlinear error correction. For a given number of cointegration relationships, general hypothesis testing is considered, where testing for linearity is of particular interest. Under...... the null of linearity, parameters of nonlinear components vanish, leading to a nonstandard testing problem. We apply so-called sup-tests to resolve this issue, which requires development of new(uniform) functional central limit theory and results for convergence of stochastic integrals. We provide a full...... asymptotic theory for estimators and test statistics. The derived asymptotic results prove to be nonstandard compared to results found elsewhere in the literature due to the impact of the estimated cointegration relations. This complicates implementation of tests motivating the introduction of bootstrap...

  13. Testing and modelling autoregressive conditional heteroskedasticity of streamflow processes

    Directory of Open Access Journals (Sweden)

    W. Wang

    2005-01-01

    Full Text Available Conventional streamflow models operate under the assumption of constant variance or season-dependent variances (e.g. ARMA (AutoRegressive Moving Average models for deseasonalized streamflow series and PARMA (Periodic AutoRegressive Moving Average models for seasonal streamflow series. However, with McLeod-Li test and Engle's Lagrange Multiplier test, clear evidences are found for the existence of autoregressive conditional heteroskedasticity (i.e. the ARCH (AutoRegressive Conditional Heteroskedasticity effect, a nonlinear phenomenon of the variance behaviour, in the residual series from linear models fitted to daily and monthly streamflow processes of the upper Yellow River, China. It is shown that the major cause of the ARCH effect is the seasonal variation in variance of the residual series. However, while the seasonal variation in variance can fully explain the ARCH effect for monthly streamflow, it is only a partial explanation for daily flow. It is also shown that while the periodic autoregressive moving average model is adequate in modelling monthly flows, no model is adequate in modelling daily streamflow processes because none of the conventional time series models takes the seasonal variation in variance, as well as the ARCH effect in the residuals, into account. Therefore, an ARMA-GARCH (Generalized AutoRegressive Conditional Heteroskedasticity error model is proposed to capture the ARCH effect present in daily streamflow series, as well as to preserve seasonal variation in variance in the residuals. The ARMA-GARCH error model combines an ARMA model for modelling the mean behaviour and a GARCH model for modelling the variance behaviour of the residuals from the ARMA model. Since the GARCH model is not followed widely in statistical hydrology, the work can be a useful addition in terms of statistical modelling of daily streamflow processes for the hydrological community.

  14. Contribution to the detection of radioactivity as applied to regular testing and to protection; Contribution a la detection des rayonnements en vue du controle et de la protection

    Energy Technology Data Exchange (ETDEWEB)

    Fuhrmann,; Joffre,; Savouyaud, [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    1. The equipment which is at the disposal of teams carrying out tests, such as the Radiations Analysis section and the Radtivity Engineers section at the CEA, has been developed from apparatus designed for laboratory research. The result of this is that even when attempts have been made to make this equipment more robust and manageable, no effort has been made to adapt the equipment to exactly what is required for assuring protection against radioactivity. It has therefore been necessary for this section to exactly specify its requirements and to carry out itself a part of the work required for developing the most suitable material. 2. The most important problems concerned the analysis of the radioactivity and the fabrication of electronic equipment, which could be available cheaply on a large scale and be also as far as possible self supporting. 3. In the present paper we briefly describe our contribution to this subject and in particular: - the improvement of methods of {gamma} ray analysis which use photographic films; - the try out of a simple and cheap technique for the analysis and spectrography of {alpha} particles; - the utilisation of new electronic material: ionisation chamber counters, scintillators; - the development of special equipment for measuring the mean flux of particles which are emitted periodically in very short bursts. (author)Fren. [French] 1. Le materiel qui se trouve a la disposition des organismes de controle, tel le Service de Controle des Radiations et de Genie Radioactif au Commissariat a l'Energie Atomique, a ete concu a partir de materiels realises pour des experiences de laboratoire et, meme lorsqu'on a pense a le rendre plus robuste et plus maniable, on a generalement omis de l'adapter exactement aux besoins de la protection contre les radiations. Aussi ce Service a-t-il ete amene a preciser exactement ses besoins et a realiser lui-meme une partie des etudes necessaires a la mise au point d'un materiel mieux adapte. 2. Les

  15. Contributions to micromechanical model of the non linear behavior of the Callovo-Oxfordian argillite; Contributions a la modelisation micromecanique du comportement non lineaire de l'argilite du callovo-oxfordien

    Energy Technology Data Exchange (ETDEWEB)

    Abou-Chakra Guery, A

    2007-12-15

    This work is performed in the general context of the project of underground disposal of radioactive waste, undertaken by the French National Radioactive Waste Management Agency (ANDRA). Due to its strong density and weak permeability, the formation of Callovo-Oxfordian argillite is chosen as one of possible geological barriers to radionuclides. The objective of the study to develop and validate a non linear homogenization approach of the mechanical behavior of Callovo-Oxfordian argillites. The material is modelled as a composite constituted of an elasto(visco)plastic clay matrix and of linear elastic or elastic damage inclusions. The macroscopic constitutive law is obtained by adapting the incremental method proposed by Hill. The derived model is first compared to Finite Element calculations on unit cell. It is then validated and applied for the prediction of the macroscopic stress-strain responses of the argillite at different geological depths. Finally, the micromechanical model is implemented in a commercial finite element code (Abaqus) for the simulation of a vertical shaft of the underground laboratory. This allows predicting the distribution of damage state and plastic strains and characterizing the excavation damage zone (EDZ). (author)

  16. Contributions to micromechanical model of the non linear behavior of the Callovo-Oxfordian argillite; Contributions a la modelisation micromecanique du comportement non lineaire de l'argilite du callovo-oxfordien

    Energy Technology Data Exchange (ETDEWEB)

    Abou-Chakra Guery, A

    2007-12-15

    This work is performed in the general context of the project of underground disposal of radioactive waste, undertaken by the French National Radioactive Waste Management Agency (ANDRA). Due to its strong density and weak permeability, the formation of Callovo-Oxfordian argillite is chosen as one of possible geological barriers to radionuclides. The objective of the study to develop and validate a non linear homogenization approach of the mechanical behavior of Callovo-Oxfordian argillites. The material is modelled as a composite constituted of an elasto(visco)plastic clay matrix and of linear elastic or elastic damage inclusions. The macroscopic constitutive law is obtained by adapting the incremental method proposed by Hill. The derived model is first compared to Finite Element calculations on unit cell. It is then validated and applied for the prediction of the macroscopic stress-strain responses of the argillite at different geological depths. Finally, the micromechanical model is implemented in a commercial finite element code (Abaqus) for the simulation of a vertical shaft of the underground laboratory. This allows predicting the distribution of damage state and plastic strains and characterizing the excavation damage zone (EDZ). (author)

  17. Testing the structure of a hydrological model using Genetic Programming

    Science.gov (United States)

    Selle, Benny; Muttil, Nitin

    2011-01-01

    SummaryGenetic Programming is able to systematically explore many alternative model structures of different complexity from available input and response data. We hypothesised that Genetic Programming can be used to test the structure of hydrological models and to identify dominant processes in hydrological systems. To test this, Genetic Programming was used to analyse a data set from a lysimeter experiment in southeastern Australia. The lysimeter experiment was conducted to quantify the deep percolation response under surface irrigated pasture to different soil types, watertable depths and water ponding times during surface irrigation. Using Genetic Programming, a simple model of deep percolation was recurrently evolved in multiple Genetic Programming runs. This simple and interpretable model supported the dominant process contributing to deep percolation represented in a conceptual model that was published earlier. Thus, this study shows that Genetic Programming can be used to evaluate the structure of hydrological models and to gain insight about the dominant processes in hydrological systems.

  18. Experimental approach and micro-mechanical modeling of the mechanical behavior of irradiated zirconium alloys; Approche experimentale et modelisation micromecanique du comportement des alliages de zirconium irradies

    Energy Technology Data Exchange (ETDEWEB)

    Onimus, F

    2003-12-01

    Zirconium alloys cladding tubes containing nuclear fuel of the Pressurized Water Reactors constitute the first safety barrier against the dissemination of radioactive elements. Thus, it is essential to predict the mechanical behavior of the material in-reactor conditions. This study aims, on the one hand, to identify and characterize the mechanisms of the plastic deformation of irradiated zirconium alloys and, on the other hand, to propose a micro-mechanical modeling based on these mechanisms. The experimental analysis shows that, for the irradiated material, the plastic deformation occurs by dislocation channeling. For transverse tensile test and internal pressure test this channeling occurs in the basal planes. However, for axial tensile test, the study revealed that the plastic deformation also occurs by channeling but in the prismatic and pyramidal planes. In addition, the study of the macroscopic mechanical behavior, compared to the deformation mechanisms observed by TEM, suggested that the internal stress is higher in the case of irradiated material than in the case of non-irradiated material, because of the very heterogeneous character of the plastic deformation. This analysis led to a coherent interpretation of the mechanical behavior of irradiated materials, in terms of deformation mechanisms. The mechanical behavior of irradiated materials was finally modeled by applying homogenization methods for heterogeneous materials. This model is able to reproduce adequately the mechanical behavior of the irradiated material, in agreement with the TEM observations. (author)

  19. Modeling of the mechanical behaviour of welded structures: behaviour laws and rupture criteria; Modelisation du comportement mecanique de structures soudees: lois de comportement et criteres de rupture

    Energy Technology Data Exchange (ETDEWEB)

    Paris, T.; Delaplanche, D. [CEA Valduc, Laboratoire Calcul et Simulations, 21120 Is-sur-Tille (France); Saanouni, K. [LASMIS-CNRS-FRE 2719, Universite de Technologie de Troyes BP 2060 - 10010 Troyes - (France)

    2006-07-01

    In the framework of the technological developments carried out in the CEA, the analysis of the mechanical behaviour of the heterogeneous welded bonds Ta/TA6V is a main preoccupation. Indeed, the welding of these two materials which cannot be distinguished by their mechanical and thermal properties induces strong microstructural heterogeneities in the melted zone. In order to characterize the behaviour of the welded joints and to develop a model of mechanical behaviour, a four points bending test on a notched specimen has been developed and implemented. This new test has allowed to obtain a macroscopic response of strength-displacement type but to analyze too more finely, with an optical extensometry and images correlation method, the influence of the heterogeneities on the local deformation of the welded joint. The confrontation of these results to a metallurgical study allows to validate the first conclusions deduced of the mechanical characterization tests and to conclude as for the local mechanisms governing the behaviour and the damage of the melted zone. The mechanical behaviour can be restored by an elasto-viscoplastic model with isotropic and non linear kinematic strain hardening coupled to this damage. The proposed model allows to identify the macroscopic behaviour of the weld bead. (O.M.)

  20. Software Testing and Verification in Climate Model Development

    Science.gov (United States)

    Clune, Thomas L.; Rood, RIchard B.

    2011-01-01

    Over the past 30 years most climate models have grown from relatively simple representations of a few atmospheric processes to a complex multi-disciplinary system. Computer infrastructure over that period has gone from punch card mainframes to modem parallel clusters. Model implementations have become complex, brittle, and increasingly difficult to extend and maintain. Existing verification processes for model implementations rely almost exclusively upon some combination of detailed analysis of output from full climate simulations and system-level regression tests. In additional to being quite costly in terms of developer time and computing resources, these testing methodologies are limited in terms of the types of defects that can be detected, isolated and diagnosed. Mitigating these weaknesses of coarse-grained testing with finer-grained "unit" tests has been perceived as cumbersome and counter-productive. In the commercial software sector, recent advances in tools and methodology have led to a renaissance for systematic fine-grained testing. We discuss the availability of analogous tools for scientific software and examine benefits that similar testing methodologies could bring to climate modeling software. We describe the unique challenges faced when testing complex numerical algorithms and suggest techniques to minimize and/or eliminate the difficulties.

  1. Testing and Modeling of Mechanical Characteristics of Resistance Welding Machines

    DEFF Research Database (Denmark)

    Wu, Pei; Zhang, Wenqi; Bay, Niels

    2003-01-01

    for both upper and lower electrode systems. This has laid a foundation for modeling the welding process and selecting the welding parameters considering the machine factors. The method is straightforward and easy to be applied in industry since the whole procedure is based on tests with no requirements......The dynamic mechanical response of resistance welding machine is very important to the weld quality in resistance welding especially in projection welding when collapse or deformation of work piece occurs. It is mainly governed by the mechanical parameters of machine. In this paper, a mathematical...... model for characterizing the dynamic mechanical responses of machine and a special test set-up called breaking test set-up are developed. Based on the model and the test results, the mechanical parameters of machine are determined, including the equivalent mass, damping coefficient, and stiffness...

  2. Reaction times to weak test lights. [psychophysics biological model

    Science.gov (United States)

    Wandell, B. A.; Ahumada, P.; Welsh, D.

    1984-01-01

    Maloney and Wandell (1984) describe a model of the response of a single visual channel to weak test lights. The initial channel response is a linearly filtered version of the stimulus. The filter output is randomly sampled over time. Each time a sample occurs there is some probability increasing with the magnitude of the sampled response - that a discrete detection event is generated. Maloney and Wandell derive the statistics of the detection events. In this paper a test is conducted of the hypothesis that the reaction time responses to the presence of a weak test light are initiated at the first detection event. This makes it possible to extend the application of the model to lights that are slightly above threshold, but still within the linear operating range of the visual system. A parameter-free prediction of the model proposed by Maloney and Wandell for lights detected by this statistic is tested. The data are in agreement with the prediction.

  3. Horns Rev II, 2D-Model Tests

    DEFF Research Database (Denmark)

    Andersen, Thomas Lykke; Frigaard, Peter

    This report present the results of 2D physical model tests carried out in the shallow wave flume at Dept. of Civil Engineering, Aalborg University (AAU). The objective of the tests was: To investigate the combined influence of the pile diameter to water depth ratio and the wave height to water...... depth ratio on wave run-up of piles. The measurements should be used to design access platforms on piles. The Model tests include: Calibration of regular and irregular sea states at the location of the pile (without structure in place). Measurement of wave run-up for the calibrated sea states...... on the front side of the pile (0 to 90 degrees). These tests have been conducted at Aalborg University from 9. October, 2006 to 8. November, 2006. Unless otherwise mentioned, all values given in this report are in model scale....

  4. Creating a simulation model of software testing using Simulink package

    Directory of Open Access Journals (Sweden)

    V. M. Dubovoi

    2016-12-01

    Full Text Available The determination of the solution model of software testing that allows prediction both the whole process and its specific stages is actual for IT-industry. The article focuses on solving this problem. The aim of the article is prediction the time and improvement the quality of software testing. The analysis of the software testing process shows that it can be attributed to the branched cyclic technological processes because it is cyclical with decision-making on control operations. The investigation uses authors' previous works andsoftware testing process method based on Markov model. The proposed method enables execution the prediction for each software module, which leads to better decision-making of each controlled suboperation of all processes. Simulink simulation model shows implementation and verification of results of proposed technique. Results of the research have practically implemented in the IT-industry.

  5. Testing R&D-Based Endogenous Growth Models

    DEFF Research Database (Denmark)

    Kruse-Andersen, Peter Kjær

    2017-01-01

    R&D-based growth models are tested using US data for the period 1953-2014. A general growth model is developed which nests the model varieties of interest. The model implies a cointegrating relationship between multifactor productivity, research intensity, and employment. This relationship...... is estimated using cointegrated VAR models. The results provide evidence against the widely used fully endogenous variety and in favor of the semi-endogenous variety. Forecasts based on the empirical estimates suggest that the slowdown in US productivity growth will continue. Particularly, the annual long...

  6. Various verifying tests using full size partial models of PCCV

    International Nuclear Information System (INIS)

    Nagata, Kaoru; Fukihara, Masaaki; Takemoto, Yasushi.

    1987-01-01

    The prestressed concrete containment vessel (PCCV) for Tsuruga No.2 plant of Japan Atomic Power Co. was adopted for the first time in Japan, and the necessity of experimental verification was pointed out about a number of items in the design and construction. In this report, the various tests carried out with full size models are described. The tendon system adopted for this PCCV is BBRV type, in which PC wires are bundled in parallel to make cables, and involves many matters inexperienced in Japan, such as the stretching capacity is as large as 1000 t class, the longest cable is 160 m, and it is the unbonded system of injecting rust inhibitor. It was demanded to confirm by testing the propriety of the small coefficient of friction at the time of stretching tendons. For the tests, the materials, equipment and their size were prepared all as those for actual works. The test works became the rehearsal of the actual prestressing works. Besides, by utilizing these full size test beds, the workability test on concrete at the time of their construction, the confirmation test on tendon strength and the safety of concrete at fixing part at the time of friction test, thereafter, greasing test, the simulation test of in-service inspection, and the thermal loading test on liners were carried out. The results of these tests are briefly reported. (Kako, I.)

  7. Measuring organizational learning. Model testing in two Romanian universities

    OpenAIRE

    Alexandra Luciana Guţă

    2014-01-01

    The scientific literature associates organizational learning with superior organization performance. If we refer to the academic environment, we appreciate that it can develop and reach better levels of performance through changes driven from the inside. Thus, through this paper we elaborate on a conceptual model of organizational learning and we test the model on a sample of employees (university teachers and researchers) from two Romanian universities. The model comprises the process of org...

  8. Tests of Financial Models in the Presence of Overlapping Observations.

    OpenAIRE

    Richardson, Matthew; Smith, Tom

    1991-01-01

    A general approach to testing serial dependence restrictions implied from financial models is developed. In particular, we discuss joint serial dependence restrictions imposed by random walk, market microstructure, and rational expectations models recently examined in the literature. This approach incorporates more information from the data by explicitly modeling dependencies induced by the use of overlapping observations. Because the estimation problem is sufficiently simple in this framewor...

  9. Autonomie du groupe restreint et performance

    Directory of Open Access Journals (Sweden)

    Elke Nissen

    2005-09-01

    Full Text Available Un groupe est autonome lorsqu'il prend lui-même en charge sa gestion (Abric, 1996 et lorsque celle-ci fonctionne bien. L'autonomie du groupe restreint est une caractéristique revendiquée dans le cadre actuel de l'expansion de dispositifs collaboratifs à distance entre apprenants. La question qui se pose alors est de savoir si un groupe restreint autonome est plus performant qu'un groupe moins autonome. L'autonomie d'un groupe d'apprentissage en ligne est-elle en relation avec la qualité de la réalisation de la tâche ? Est-elle en relation avec les progrès réalisés par les membres du groupe ? Dans le cadre de notre étude expérimentale, menée dans deux dispositifs pédagogiques différents (l'environnement d'apprentissage Babbelnet et une formation sur la plate-forme Acolad, des étudiants ont réalisé en groupes restreints, avec l'accompagnement d'un tuteur, une tâche de type actionnel – en l'occurrence une rédaction en langue étrangère (allemand ou anglais. Pour ce faire, ils disposaient d'aides méthodologiques et linguistiques dans l'environnement pédagogique en ligne. Ils ont interagi par le biais d'Internet au moyen de différents outils de communication. Une analyse de l'interaction qui a eu lieu dans chaque groupe, l'évaluation des rédactions réalisées conjointement, deux tests réalisés respectivement avant et après la phase de travail en groupe ainsi qu'un formulaire auto-administré nous permettent de mettre en lien l'autonomie des groupes, d'une part, et leur performance, voire leur apprentissage, d'autre part. Au vu de cette étude, il apparaît que l'autonomie du groupe n'a pas d'influence directe sur l'apprentissage des groupes restreints. En revanche, un rapport est visible entre l'appréciation du fonctionnement du groupe par ses membres et l'évolution de la performance des groupes.

  10. Model of ASTM Flammability Test in Microgravity: Iron Rods

    Science.gov (United States)

    Steinberg, Theodore A; Stoltzfus, Joel M.; Fries, Joseph (Technical Monitor)

    2000-01-01

    There is extensive qualitative results from burning metallic materials in a NASA/ASTM flammability test system in normal gravity. However, this data was shown to be inconclusive for applications involving oxygen-enriched atmospheres under microgravity conditions by conducting tests using the 2.2-second Lewis Research Center (LeRC) Drop Tower. Data from neither type of test has been reduced to fundamental kinetic and dynamic systems parameters. This paper reports the initial model analysis for burning iron rods under microgravity conditions using data obtained at the LERC tower and modeling the burning system after ignition. Under the conditions of the test the burning mass regresses up the rod to be detached upon deceleration at the end of the drop. The model describes the burning system as a semi-batch, well-mixed reactor with product accumulation only. This model is consistent with the 2.0-second duration of the test. Transient temperature and pressure measurements are made on the chamber volume. The rod solid-liquid interface melting rate is obtained from film records. The model consists of a set of 17 non-linear, first-order differential equations which are solved using MATLAB. This analysis confirms that a first-order rate, in oxygen concentration, is consistent for the iron-oxygen kinetic reaction. An apparent activation energy of 246.8 kJ/mol is consistent for this model.

  11. Horns Rev II, 2D-Model Tests

    DEFF Research Database (Denmark)

    Andersen, Thomas Lykke; Brorsen, Michael

    This report present the results of 2D physical model tests carried out in the shallow wave flume at Dept. of Civil Engineering, Aalborg University (AAU), Denmark. The starting point for the present report is the previously carried out run-up tests described in Lykke Andersen & Frigaard, 2006. The......-shaped access platforms on piles. The Model tests include mainly regular waves and a few irregular wave tests. These tests have been conducted at Aalborg University from 9. November, 2006 to 17. November, 2006.......This report present the results of 2D physical model tests carried out in the shallow wave flume at Dept. of Civil Engineering, Aalborg University (AAU), Denmark. The starting point for the present report is the previously carried out run-up tests described in Lykke Andersen & Frigaard, 2006....... The objective of the tests was to investigate the impact pressures generated on a horizontal platform and a cone platform for selected sea states calibrated by Lykke Andersen & Frigaard, 2006. The measurements should be used for assessment of slamming coefficients for the design of horizontal and cone...

  12. NET model coil test possibilities in the TOSKA TWIN configuration

    International Nuclear Information System (INIS)

    Gruenhagen, A.; Heller, R.; Herz, W.; Hofmann, A.; Jentzsch, K.; Kapulla, H.; Kneifel, B.; Komarek, P.; Lehmann, W.; Maurer, W.; Ulbricht, A.; Vogt, A.; Zahn, G.

    1989-07-01

    This report continues an earlier one on the possibilities of NET model coil testing in the TOSKA Upgrade facility at KfK. The investigation of a 'Cluster Test Facility' and a 'Solenoid Test Facility' is followed by the investigation of two further test arrangements. They are called 'Twin Configurations'. One common feature of both arrangements is that the EURATOM-LCT-coil delivers a background magnetic field. This coil should be operated at a temperature of 1.8 K and an enhanced current up to 20 kA compared to the LCT test where 3.5 K and up to 16 kA were the operating conditions. In one configuration the NET model test coil is adjacent to the LCT coil (ATC = Adjacent Twin Configuration), in the other one the NET model coil is inserted into the bore of LCT coil (ITC = Inserted Twin Configuration) either upright or with a 60 0 C slope. The configurations are investigated with respect to their electromagnetic mechanical and thermo-hydraulic properties. The requirements for the necessary mechanical support structure of the LCT coil were computed. Installation and cooling of the whole system were discussed. The time schedule and the costs for the test facility modification were estimated. Advantages and disadvantages for the configurations were discussed with respect to feasibility of the test arrangement and operation. (orig.) [de

  13. Animal models of toxicology testing: the role of pigs.

    Science.gov (United States)

    Helke, Kristi L; Swindle, Marvin Michael

    2013-02-01

    In regulatory toxicological testing, both a rodent and non-rodent species are required. Historically, dogs and non-human primates (NHP) have been the species of choice of the non-rodent portion of testing. The pig is an appropriate option for these tests based on metabolic pathways utilized in xenobiotic biotransformation. This review focuses on the Phase I and Phase II biotransformation pathways in humans and pigs and highlights the similarities and differences of these models. This is a growing field and references are sparse. Numerous breeds of pigs are discussed along with specific breed differences in these enzymes that are known. While much available data are presented, it is grossly incomplete and sometimes contradictory based on methods used. There is no ideal species to use in toxicology. The use of dogs and NHP in xenobiotic testing continues to be the norm. Pigs present a viable and perhaps more reliable model of non-rodent testing.

  14. Testing and Inference in Nonlinear Cointegrating Vector Error Correction Models

    DEFF Research Database (Denmark)

    Kristensen, Dennis; Rahbæk, Anders

    In this paper, we consider a general class of vector error correction models which allow for asymmetric and non-linear error correction. We provide asymptotic results for (quasi-)maximum likelihood (QML) based estimators and tests. General hypothesis testing is considered, where testing...... of non-stationary non-linear time series models. Thus the paper provides a full asymptotic theory for estimators as well as standard and non-standard test statistics. The derived asymptotic results prove to be new compared to results found elsewhere in the literature due to the impact of the estimated...... symmetric non-linear error correction considered. A simulation study shows that the fi…nite sample properties of the bootstrapped tests are satisfactory with good size and power properties for reasonable sample sizes....

  15. Testing and Inference in Nonlinear Cointegrating Vector Error Correction Models

    DEFF Research Database (Denmark)

    Kristensen, Dennis; Rahbek, Anders

    In this paper, we consider a general class of vector error correction models which allow for asymmetric and non-linear error correction. We provide asymptotic results for (quasi-)maximum likelihood (QML) based estimators and tests. General hypothesis testing is considered, where testing...... of non-stationary non-linear time series models. Thus the paper provides a full asymptotic theory for estimators as well as standard and non-standard test statistics. The derived asymptotic results prove to be new compared to results found elsewhere in the literature due to the impact of the estimated...... symmetric non-linear error correction are considered. A simulation study shows that the finite sample properties of the bootstrapped tests are satisfactory with good size and power properties for reasonable sample sizes....

  16. Old star clusters: Bench tests of low mass stellar models

    Directory of Open Access Journals (Sweden)

    Salaris M.

    2013-03-01

    Full Text Available Old star clusters in the Milky Way and external galaxies have been (and still are traditionally used to constrain the age of the universe and the timescales of galaxy formation. A parallel avenue of old star cluster research considers these objects as bench tests of low-mass stellar models. This short review will highlight some recent tests of stellar evolution models that make use of photometric and spectroscopic observations of resolved old star clusters. In some cases these tests have pointed to additional physical processes efficient in low-mass stars, that are not routinely included in model computations. Moreover, recent results from the Kepler mission about the old open cluster NGC6791 are adding new tight constraints to the models.

  17. Comparison of Critical Flow Models' Evaluations for SBLOCA Tests

    International Nuclear Information System (INIS)

    Kim, Yeon Sik; Park, Hyun Sik; Cho, Seok

    2016-01-01

    A comparison of critical flow models between the Trapp-Ransom and Henry-Fauske models for all SBLOCA (small break loss of coolant accident) scenarios of the ATLAS (Advanced thermal-hydraulic test loop for accident simulation) facility was performed using the MARS-KS code. For the comparison of the two critical models, the accumulated break mass was selected as the main parameter for the comparison between the analyses and tests. Four cases showed the same respective discharge coefficients between the two critical models, e.g., 6' CL (cold leg) break and 25%, 50%, and 100% DVI (direct vessel injection) breaks. In the case of the 4' CL break, no reasonable results were obtained with any possible Cd values. In addition, typical system behaviors, e.g., PZR (pressurizer) pressure and collapsed core water level, were also compared between the two critical models. Four cases showed the same respective discharge coefficients between the two critical models, e.g., 6' CL break and 25%, 50%, and 100% DVI breaks. In the case of the 4' CL break, no reasonable results were obtained with any possible Cd values. In addition, typical system behaviors, e.g., PZR pressure and collapsed core water level, were also compared between the two critical models. From the comparison between the two critical models for the CL breaks, the Trapp-Ransom model predicted quite well with respect to the other model for the smallest and larger breaks, e.g., 2', 6', and 8.5' CL breaks. In addition, from the comparison between the two critical models for the DVI breaks, the Trapp-Ransom model predicted quite well with respect to the other model for the smallest and larger breaks, e.g., 5%, 50%, and 100% DVI breaks. In the case of the 50% and 100% breaks, the two critical models predicted the test data quite well.

  18. Penetration Testing Professional Ethics: a conceptual model and taxonomy

    Directory of Open Access Journals (Sweden)

    Justin Pierce

    2006-05-01

    Full Text Available In an environment where commercial software is continually patched to correct security flaws, penetration testing can provide organisations with a realistic assessment of their security posture. Penetration testing uses the same principles as criminal hackers to penetrate corporate networks and thereby verify the presence of software vulnerabilities. Network administrators can use the results of a penetration test to correct flaws and improve overall security. The use of hacking techniques, however, raises several ethical questions that centre on the integrity of the tester to maintain professional distance and uphold the profession. This paper discusses the ethics of penetration testing and presents our conceptual model and revised taxonomy.

  19. Preliminary results of steel containment vessel model test

    International Nuclear Information System (INIS)

    Matsumoto, T.; Komine, K.; Arai, S.

    1997-01-01

    A high pressure test of a mixed-scaled model (1:10 in geometry and 1:4 in shell thickness) of a steel containment vessel (SCV), representing an improved boiling water reactor (BWR) Mark II containment, was conducted on December 11-12, 1996 at Sandia National Laboratories. This paper describes the preliminary results of the high pressure test. In addition, the preliminary post-test measurement data and the preliminary comparison of test data with pretest analysis predictions are also presented

  20. Le bal du loup

    CERN Multimedia

    Happy Children's Home

    2013-01-01

    The Bord'eau amateur theatre group will graciously perform a play of their creation Le bal du loup Saturday 19 October 2013 at 20:00 Sunday 20 October at 17:00 in the Théâtre des Grottes Rue Louis Favre 43, 1201 Genève Children from age 12 upwards. Summary: The new-elected mayoress of a small village would like to clean up the town by prohibiting alcohol and getting rid of its prostitutes. Then along comes « Massimo Lupo » the pimp... The performances will be given to support the Happy Children's Home charity, which runs a foster-home in Pokhara for Nepali children:  http://www.happychildrenshome.org/ Admission : minimum charge of 10 CHF per person requested, to cover the cost of technical assistance and theatre rental. Any profit will be used solely for the foster-home. At the end of each performance members of the HCH charity will be happy to answer any questions you may have. The theatre has 86 seats, thank you for reserv...

  1. SEB circuit-level model in N-channel power MOSFETs; Modele pour circuits du burnout dans des MOSFETs de puissance de type N

    Energy Technology Data Exchange (ETDEWEB)

    Liu, J.; Schrimpf, R.D.; Massengill, L.; Galloway, K.F. [Vanderbilt Univ., Nashville, TN (United States)

    1999-07-01

    A Single Event Burnout (SEB) circuit model has been developed. The dependence of SEB sensitivity on various parameters is presented and compared with experimental results. The parasitic resistance and capacitance of the device as well as the circuit parameters contribute to the length of SEB pulse. Increasing the switching frequency of the power MOSFET may be a possible way to prevent SEB in applications. (authors)

  2. Physics of flavor beyond the standard model and extra-dimensions; Physique de la saveur au-dela du modele standard et dimensions supplementaires

    Energy Technology Data Exchange (ETDEWEB)

    Welzel, J

    2006-11-15

    Even if the Standard Model (SM) of particle physics meets an extraordinary experimental success, some fundamental questions remain unanswered (origin of hierarchies, observed mixing pattern in neutrino and quark sectors...). We need to go beyond the SM and to find new principles/symmetries. The aim of this thesis is to study the phenomenology of supersymmetric and/or extra-dimensional models and to look at deviations from the SM, in the flavour sector. First, we addressed the question of baryon- and lepton-number conservation through R-parity in low-energy supersymmetric models. Precisely, we studied its violation using experimental data and the rare kaon decay K {yields} {pi}{nu}{nu}-bar to derive upper limits on R-parity violating couplings involved in it. In this context we have pointed out the importance of R-parity conserving contributions and their interferences with R-parity violating ones. In the second part, we studied effects of an extra dimension (space-like and compactified) on several examples: quantum electrodynamics and gauge invariance, strong and electroweak unification, neutrino masses and mixing angles. Typically, adding an extra dimension reduces the predictive power. However, we are still able to know generic behaviours (order of magnitude predictions). In particular, we pointed out the possibility of a weak neutrino mixing pattern (CKM-like) at high energy for a relevant and reasonable parameter space. This opens up new perspectives in the study of flavour symmetries and bonds between quark and leptons. (author)

  3. Ontological Analysis of Integrated Process Models: testing hypotheses

    Directory of Open Access Journals (Sweden)

    Michael Rosemann

    2001-11-01

    Full Text Available Integrated process modeling is achieving prominence in helping to document and manage business administration and IT processes in organizations. The ARIS framework is a popular example for a framework of integrated process modeling not least because it underlies the 800 or more reference models embedded in the world's most popular ERP package, SAP R/3. This paper demonstrates the usefulness of the Bunge-Wand-Weber (BWW representation model for evaluating modeling grammars such as those constituting ARIS. It reports some initial insights gained from pilot testing Green and Rosemann's (2000 evaluative propositions. Even when considering all five views of ARIS, modelers have problems representing business rules, the scope and boundary of systems, and decomposing models. However, even though it is completely ontologically redundant, users still find the function view useful in modeling.

  4. Test-driven verification/validation of model transformations

    Institute of Scientific and Technical Information of China (English)

    László LENGYEL; Hassan CHARAF

    2015-01-01

    Why is it important to verify/validate model transformations? The motivation is to improve the quality of the trans-formations, and therefore the quality of the generated software artifacts. Verified/validated model transformations make it possible to ensure certain properties of the generated software artifacts. In this way, verification/validation methods can guarantee different requirements stated by the actual domain against the generated/modified/optimized software products. For example, a verified/ validated model transformation can ensure the preservation of certain properties during the model-to-model transformation. This paper emphasizes the necessity of methods that make model transformation verified/validated, discusses the different scenarios of model transformation verification and validation, and introduces the principles of a novel test-driven method for verifying/ validating model transformations. We provide a solution that makes it possible to automatically generate test input models for model transformations. Furthermore, we collect and discuss the actual open issues in the field of verification/validation of model transformations.

  5. In Search of Optimal Cognitive Diagnostic Model(s) for ESL Grammar Test Data

    Science.gov (United States)

    Yi, Yeon-Sook

    2017-01-01

    This study compares five cognitive diagnostic models in search of optimal one(s) for English as a Second Language grammar test data. Using a unified modeling framework that can represent specific models with proper constraints, the article first fit the full model (the log-linear cognitive diagnostic model, LCDM) and investigated which model…

  6. SPSS and SAS programming for the testing of mediation models.

    Science.gov (United States)

    Dudley, William N; Benuzillo, Jose G; Carrico, Mineh S

    2004-01-01

    Mediation modeling can explain the nature of the relation among three or more variables. In addition, it can be used to show how a variable mediates the relation between levels of intervention and outcome. The Sobel test, developed in 1990, provides a statistical method for determining the influence of a mediator on an intervention or outcome. Although interactive Web-based and stand-alone methods exist for computing the Sobel test, SPSS and SAS programs that automatically run the required regression analyses and computations increase the accessibility of mediation modeling to nursing researchers. To illustrate the utility of the Sobel test and to make this programming available to the Nursing Research audience in both SAS and SPSS. The history, logic, and technical aspects of mediation testing are introduced. The syntax files sobel.sps and sobel.sas, created to automate the computation of the regression analysis and test statistic, are available from the corresponding author. The reported programming allows the user to complete mediation testing with the user's own data in a single-step fashion. A technical manual included with the programming provides instruction on program use and interpretation of the output. Mediation modeling is a useful tool for describing the relation between three or more variables. Programming and manuals for using this model are made available.

  7. Inner ear test battery in guinea pig models - a review.

    Science.gov (United States)

    Young, Yi-Ho

    2018-06-01

    This study reviewed the development of the inner ear test battery comprising auditory brainstem response (ABR), and caloric, ocular vestibular-evoked myogenic potential (oVEMP), and cervical vestibular-evoked myogenic potential (cVEMP) tests in guinea pig models at our laboratory over the last 20 years. Detailed description of the methodology for testing the small animals is also included. Inner ear disorders, i.e. ototoxicity, noise exposure, or perilymph fistula were established in guinea pig models first. One to four weeks after operation, each animal underwent ABR, oVEMP, cVEMP, and caloric tests. Then, animals were sacrificed for morphological study in the temporal bones. Inner ear endorgans can be comprehensively evaluated in guinea pig models via an inner ear test battery, which provides thorough information on the cochlea, saccule, utricle, and semicircular canal function of guinea pigs. Coupled with morphological study in the temporal bones of the animals may help elucidate the mechanism of inner ear disorders in humans. The inner ear test battery in guinea pig models may encourage young researchers to perform basic study in animals and stimulate the progress of experimental otology which is in evolution.

  8. Feasibility of Seismic Monitoring at a Potential CO2 Injection Test Site in the Paris Basin Évaluation des apports de la sismique à la surveillance d’un test d’injection de CO2 sur un site pilote potentiel du Bassin de Paris

    Directory of Open Access Journals (Sweden)

    Becquey M.

    2009-09-01

    Full Text Available Seismic effects of the injection of CO2 into a partially depleted oil field have been evaluated. Seismic modelling yields small time-lapse effects, including 0.4 ms time-shifts and 4 to 6% amplitude variations at the top and bottom of the reservoir. Amplitude variations at the reservoir level should be slightly larger at large incidence angles, but wave equation modelling shows that picking these reflections will not be easy, because of the presence of shear waves generated at upper interfaces. In-situ fracturation generates azimuthal anisotropy with velocity and amplitude variations with the propagation direction. These variations bear some information about the crack density, about the relation between the fracture nets and the porous medium, and about the fluid content in the pores and fractures. All these effects are however weak and their measurement requires careful seismic data acquisition and processing. Les effets sismiques de l’injection de dioxyde de carbone dans un gisement de petrole deplete ont fait l’objet d’une simulation. Ces effets sont faibles. On peut s’attendre a une variation des temps d’arrivee des reflexions sur des interfaces situees en dessous des reservoirs, de l’ordre de la demi-milliseconde, et a une variation d’amplitude au toit et au mur du reservoir de l’ordre de 6 %. La variation d’amplitude sera legerement plus forte pour les reflexions a grand deport, mais le pointe des reflexions et la mesure des amplitudes seront probablement plus difficiles, en raison de la presence d’ondes converties. La mesure de l’anisotropie azimutale, due a la presence de fractures, peut nous donner des informations sur l’etat de fracturation du reservoir et sur la connexion entre ces fractures et la matrice poreuse. La mesure de ces variations subtiles necessitera une acquisition soignee et un traitement precautionneux des donnees.

  9. Experiences with testing PCRV concrete and epoxy resin models

    International Nuclear Information System (INIS)

    Schimmelpfennig, K.; Schnellenbach, G.

    1979-01-01

    A 1:5 scale model of a prestressed concrete pressure vessel was used to investigate its operating behaviour when only partially prestressed so as to allow cracking even under operating conditions. Further experimental work consisted in the building and testing of epoxy resin models to check the results of three-dimensional numerical calculations. Results show that a partially prestressed vessel will operate reliably and that deformations under both short and long-term internal pressure are essentially reversible. The results from the epoxy resin models show that building such models also with complicated geometries and with embedded strain gauges can be successfully carried out and that testing such models is a good tool for checking computer calculations

  10. Conditional Monte Carlo randomization tests for regression models.

    Science.gov (United States)

    Parhat, Parwen; Rosenberger, William F; Diao, Guoqing

    2014-08-15

    We discuss the computation of randomization tests for clinical trials of two treatments when the primary outcome is based on a regression model. We begin by revisiting the seminal paper of Gail, Tan, and Piantadosi (1988), and then describe a method based on Monte Carlo generation of randomization sequences. The tests based on this Monte Carlo procedure are design based, in that they incorporate the particular randomization procedure used. We discuss permuted block designs, complete randomization, and biased coin designs. We also use a new technique by Plamadeala and Rosenberger (2012) for simple computation of conditional randomization tests. Like Gail, Tan, and Piantadosi, we focus on residuals from generalized linear models and martingale residuals from survival models. Such techniques do not apply to longitudinal data analysis, and we introduce a method for computation of randomization tests based on the predicted rate of change from a generalized linear mixed model when outcomes are longitudinal. We show, by simulation, that these randomization tests preserve the size and power well under model misspecification. Copyright © 2014 John Wiley & Sons, Ltd.

  11. Development of a fault test experimental facility model using Matlab

    Energy Technology Data Exchange (ETDEWEB)

    Pereira, Iraci Martinez; Moraes, Davi Almeida, E-mail: martinez@ipen.br, E-mail: dmoraes@dk8.com.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2015-07-01

    The Fault Test Experimental Facility was developed to simulate a PWR nuclear power plant and is instrumented with temperature, level and pressure sensors. The Fault Test Experimental Facility can be operated to generate normal and fault data, and these failures can be added initially small, and their magnitude being increasing gradually. This work presents the Fault Test Experimental Facility model developed using the Matlab GUIDE (Graphical User Interface Development Environment) toolbox that consists of a set of functions designed to create interfaces in an easy and fast way. The system model is based on the mass and energy inventory balance equations. Physical as well as operational aspects are taken into consideration. The interface layout looks like a process flowchart and the user can set the input variables. Besides the normal operation conditions, there is the possibility to choose a faulty variable from a list. The program also allows the user to set the noise level for the input variables. Using the model, data were generated for different operational conditions, both under normal and fault conditions with different noise levels added to the input variables. Data generated by the model will be compared with Fault Test Experimental Facility data. The Fault Test Experimental Facility theoretical model results will be used for the development of a Monitoring and Fault Detection System. (author)

  12. Development of a fault test experimental facility model using Matlab

    International Nuclear Information System (INIS)

    Pereira, Iraci Martinez; Moraes, Davi Almeida

    2015-01-01

    The Fault Test Experimental Facility was developed to simulate a PWR nuclear power plant and is instrumented with temperature, level and pressure sensors. The Fault Test Experimental Facility can be operated to generate normal and fault data, and these failures can be added initially small, and their magnitude being increasing gradually. This work presents the Fault Test Experimental Facility model developed using the Matlab GUIDE (Graphical User Interface Development Environment) toolbox that consists of a set of functions designed to create interfaces in an easy and fast way. The system model is based on the mass and energy inventory balance equations. Physical as well as operational aspects are taken into consideration. The interface layout looks like a process flowchart and the user can set the input variables. Besides the normal operation conditions, there is the possibility to choose a faulty variable from a list. The program also allows the user to set the noise level for the input variables. Using the model, data were generated for different operational conditions, both under normal and fault conditions with different noise levels added to the input variables. Data generated by the model will be compared with Fault Test Experimental Facility data. The Fault Test Experimental Facility theoretical model results will be used for the development of a Monitoring and Fault Detection System. (author)

  13. Model Selection in Continuous Test Norming With GAMLSS.

    Science.gov (United States)

    Voncken, Lieke; Albers, Casper J; Timmerman, Marieke E

    2017-06-01

    To compute norms from reference group test scores, continuous norming is preferred over traditional norming. A suitable continuous norming approach for continuous data is the use of the Box-Cox Power Exponential model, which is found in the generalized additive models for location, scale, and shape. Applying the Box-Cox Power Exponential model for test norming requires model selection, but it is unknown how well this can be done with an automatic selection procedure. In a simulation study, we compared the performance of two stepwise model selection procedures combined with four model-fit criteria (Akaike information criterion, Bayesian information criterion, generalized Akaike information criterion (3), cross-validation), varying data complexity, sampling design, and sample size in a fully crossed design. The new procedure combined with one of the generalized Akaike information criterion was the most efficient model selection procedure (i.e., required the smallest sample size). The advocated model selection procedure is illustrated with norming data of an intelligence test.

  14. Approches pour la reduction de l'impact de defaut dans le transport d'energie du parc eolien offshore via VSC-HVDC =

    Science.gov (United States)

    Benadja, Mounir

    nouvelle commande proposee MRAC qui reduit la profondeur de l'impact a 35%. Lors de l'apparition des defauts AC et DC, une reduction de l'impact des defauts sur l'amplitude des courants de reseau AC terrestre et du temps de reponse a ete observee et la stabilite du systeme a ete renforcee par l'utilisation de la commande adaptative basee sur le modele de reference MRAC. La quatrieme contribution concerne une nouvelle commande basee sur le mode de glissement (SM) appliquee pour la station VSC-HVDC qui relie le parc eolien offshore (OWF) au reseau principal AC. Ce parc est compose de dix eoliennes basees sur des generatrices synchrones a aimant permanent (VSWT/PMSGs) connectees en parallele et chacune est controlee par son propre convertisseur DC-DC. Une comparaison des performances entre la commande SM et de la commande non-lineaire avec des controleurs PI pour les deux conditions (presence et absence de defaut DC) a ete analysee et montre la superiorite de la commande par SM. Un prototype du systeme etudie a echelle reduite a ete realise et teste au laboratoire GREPCI en utilisant la carte dSPACE-DS1104 pour la validation experimentale. L'analyse et la simulation des systemes etudies sont developpees sous l'environnement Matlab/Simulink/Simpowersystem. Les resultats obtenus a partir des configurations developpees sont valides par simulation et par experimentation. Les performances sont tres satisfaisantes du point de vue reponse dynamique, reponse en regime permanent, stabilite du systeme et qualite de l'energie.

  15. Development of Test-Analysis Models (TAM) for correlation of dynamic test and analysis results

    Science.gov (United States)

    Angelucci, Filippo; Javeed, Mehzad; Mcgowan, Paul

    1992-01-01

    The primary objective of structural analysis of aerospace applications is to obtain a verified finite element model (FEM). The verified FEM can be used for loads analysis, evaluate structural modifications, or design control systems. Verification of the FEM is generally obtained as the result of correlating test and FEM models. A test analysis model (TAM) is very useful in the correlation process. A TAM is essentially a FEM reduced to the size of the test model, which attempts to preserve the dynamic characteristics of the original FEM in the analysis range of interest. Numerous methods for generating TAMs have been developed in the literature. The major emphasis of this paper is a description of the procedures necessary for creation of the TAM and the correlation of the reduced models with the FEM or the test results. Herein, three methods are discussed, namely Guyan, Improved Reduced System (IRS), and Hybrid. Also included are the procedures for performing these analyses using MSC/NASTRAN. Finally, application of the TAM process is demonstrated with an experimental test configuration of a ten bay cantilevered truss structure.

  16. Target Soil Impact Verification: Experimental Testing and Kayenta Constitutive Modeling.

    Energy Technology Data Exchange (ETDEWEB)

    Broome, Scott Thomas [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Flint, Gregory Mark [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Dewers, Thomas [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Newell, Pania [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)

    2015-11-01

    This report details experimental testing and constitutive modeling of sandy soil deformation under quasi - static conditions. This is driven by the need to understand constitutive response of soil to target/component behavior upon impact . An experimental and constitutive modeling program was followed to determine elastic - plastic properties and a compressional failure envelope of dry soil . One hydrostatic, one unconfined compressive stress (UCS), nine axisymmetric compression (ACS) , and one uniaxial strain (US) test were conducted at room temperature . Elastic moduli, assuming isotropy, are determined from unload/reload loops and final unloading for all tests pre - failure and increase monotonically with mean stress. Very little modulus degradation was discernable from elastic results even when exposed to mean stresses above 200 MPa . The failure envelope and initial yield surface were determined from peak stresses and observed onset of plastic yielding from all test results. Soil elasto - plastic behavior is described using the Brannon et al. (2009) Kayenta constitutive model. As a validation exercise, the ACS - parameterized Kayenta model is used to predict response of the soil material under uniaxial strain loading. The resulting parameterized and validated Kayenta model is of high quality and suitable for modeling sandy soil deformation under a range of conditions, including that for impact prediction.

  17. Testing the predictive power of nuclear mass models

    International Nuclear Information System (INIS)

    Mendoza-Temis, J.; Morales, I.; Barea, J.; Frank, A.; Hirsch, J.G.; Vieyra, J.C. Lopez; Van Isacker, P.; Velazquez, V.

    2008-01-01

    A number of tests are introduced which probe the ability of nuclear mass models to extrapolate. Three models are analyzed in detail: the liquid drop model, the liquid drop model plus empirical shell corrections and the Duflo-Zuker mass formula. If predicted nuclei are close to the fitted ones, average errors in predicted and fitted masses are similar. However, the challenge of predicting nuclear masses in a region stabilized by shell effects (e.g., the lead region) is far more difficult. The Duflo-Zuker mass formula emerges as a powerful predictive tool

  18. A test of the hierarchical model of litter decomposition

    DEFF Research Database (Denmark)

    Bradford, Mark A.; Veen, G. F.; Bonis, Anne

    2017-01-01

    Our basic understanding of plant litter decomposition informs the assumptions underlying widely applied soil biogeochemical models, including those embedded in Earth system models. Confidence in projected carbon cycle-climate feedbacks therefore depends on accurate knowledge about the controls...... regulating the rate at which plant biomass is decomposed into products such as CO2. Here we test underlying assumptions of the dominant conceptual model of litter decomposition. The model posits that a primary control on the rate of decomposition at regional to global scales is climate (temperature...

  19. Effets de la microdose sur la production du niébé, du mil et du ...

    African Journals Online (AJOL)

    Effets de la microdose sur la production du niébé, du mil et du sorgho en fonction la toposéquence. Fatimata Saba, Sibiri Jean Baptiste Taonda, Idriss Serme, Alimata A. Bandaogo, Augustin P. Sourwema, Adama Kabre ...

  20. Dynamique des populations du foreur des tiges du cacaoyer ...

    African Journals Online (AJOL)

    SARAH

    30 nov. 2014 ... déprédateur dans la région du Haut-Sassandra, la deuxième plus grande région de production de cacao en. Côte d'ivoire. Méthodologie et résultats : L'étude a été réalisée de 2009 à 2013 dans les plantations villageoises de la région du Haut-Sassandra en Côte d'Ivoire. Les variations des taux d'attaques ...

  1. Dynamique des populations du foreur des tiges du cacaoyer ...

    African Journals Online (AJOL)

    Objectif : Le foreur de tiges du cacaoyer, Eulophonotus myrmeleon Felder cause aujourd'hui d'énormes dégâts dans les cacaoyères ivoiriennes. La présente étude vise à déterminer les périodes de fortes attaques de ce déprédateur dans la région du Haut-Sassandra, la deuxième plus grande région de production de ...

  2. Goodness-of-fit tests in mixed models

    KAUST Repository

    Claeskens, Gerda

    2009-05-12

    Mixed models, with both random and fixed effects, are most often estimated on the assumption that the random effects are normally distributed. In this paper we propose several formal tests of the hypothesis that the random effects and/or errors are normally distributed. Most of the proposed methods can be extended to generalized linear models where tests for non-normal distributions are of interest. Our tests are nonparametric in the sense that they are designed to detect virtually any alternative to normality. In case of rejection of the null hypothesis, the nonparametric estimation method that is used to construct a test provides an estimator of the alternative distribution. © 2009 Sociedad de Estadística e Investigación Operativa.

  3. Automated particulate sampler field test model operations guide

    Energy Technology Data Exchange (ETDEWEB)

    Bowyer, S.M.; Miley, H.S.

    1996-10-01

    The Automated Particulate Sampler Field Test Model Operations Guide is a collection of documents which provides a complete picture of the Automated Particulate Sampler (APS) and the Field Test in which it was evaluated. The Pacific Northwest National Laboratory (PNNL) Automated Particulate Sampler was developed for the purpose of radionuclide particulate monitoring for use under the Comprehensive Test Ban Treaty (CTBT). Its design was directed by anticipated requirements of small size, low power consumption, low noise level, fully automatic operation, and most predominantly the sensitivity requirements of the Conference on Disarmament Working Paper 224 (CDWP224). This guide is intended to serve as both a reference document for the APS and to provide detailed instructions on how to operate the sampler. This document provides a complete description of the APS Field Test Model and all the activity related to its evaluation and progression.

  4. Initial CGE Model Results Summary Exogenous and Endogenous Variables Tests

    Energy Technology Data Exchange (ETDEWEB)

    Edwards, Brian Keith [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Boero, Riccardo [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Rivera, Michael Kelly [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-08-07

    The following discussion presents initial results of tests of the most recent version of the National Infrastructure Simulation and Analysis Center Dynamic Computable General Equilibrium (CGE) model developed by Los Alamos National Laboratory (LANL). The intent of this is to test and assess the model’s behavioral properties. The test evaluated whether the predicted impacts are reasonable from a qualitative perspective. This issue is whether the predicted change, be it an increase or decrease in other model variables, is consistent with prior economic intuition and expectations about the predicted change. One of the purposes of this effort is to determine whether model changes are needed in order to improve its behavior qualitatively and quantitatively.

  5. Active earth pressure model tests versus finite element analysis

    Science.gov (United States)

    Pietrzak, Magdalena

    2017-06-01

    The purpose of the paper is to compare failure mechanisms observed in small scale model tests on granular sample in active state, and simulated by finite element method (FEM) using Plaxis 2D software. Small scale model tests were performed on rectangular granular sample retained by a rigid wall. Deformation of the sample resulted from simple wall translation in the direction `from the soil" (active earth pressure state. Simple Coulomb-Mohr model for soil can be helpful in interpreting experimental findings in case of granular materials. It was found that the general alignment of strain localization pattern (failure mechanism) may belong to macro scale features and be dominated by a test boundary conditions rather than the nature of the granular sample.

  6. DU Processing Efficiency and Reclamation: Plasma Arc Melting

    Energy Technology Data Exchange (ETDEWEB)

    Imhoff, Seth D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Aikin, Jr., Robert M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Swenson, Hunter [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Solis, Eunice Martinez [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-09-26

    The work described here corresponds to one piece of a larger effort to increase material usage efficiency during DU processing operations. In order to achieve this goal, multiple technologies and approaches are being tested. These technologies occupy a spectrum of technology readiness levels (TRLs). Plasma arc melting (PAM) is one of the technologies being investigated. PAM utilizes a high temperature plasma to melt materials. Depending on process conditions, there are potential opportunities for recycling and material reclamation. When last routinely operational, the LANL research PAM showed extremely promising results for recycling and reclamation of DU and DU alloys. The current TRL is lower due to machine idleness for nearly two decades, which has proved difficult to restart. This report describes the existing results, promising techniques, and the process of bringing this technology back to readiness at LANL.

  7. Model tests of geosynthetic reinforced slopes in a geotechnical centrifuge

    International Nuclear Information System (INIS)

    Aklik, P.

    2012-01-01

    Geosynthetic-reinforced slopes and walls became very popular in recent years because of their financial, technical, and ecological advantages. Centrifuge modelling is a powerful tool for physical modelling of reinforced slopes and offers the advantage to observe the failure mechanisms of the slopes. In order to replicate the gravity induced stresses of a prototype structure in a geometrically 1/N reduced model, it is necessary to test the model in a gravitational field N times larger than that of the prototype structure. In this dissertation, geotextile-reinforced slope models were tested in a geotechnical centrifuge to identify the possible failure mechanisms. Slope models were tested by varying slope inclination, tensile strengths of the geotextiles, and overlapping lengths. Photographs of the geotextile reinforced slope models in flight were taken with a digital camera and the soil deformations of geotextile reinforced slopes were evaluated with Particle Image Velocimetry (PIV). The experimental results showed that failure of the centrifuge models initiated at midheight of the slope, and occurred due to geotextile breakage instead of pullout. The location of the shear surface is independent of the tensile strength of the geotextile; it is dependent on the shear strength of the soil. It is logical to see that the required acceleration of the centrifuge at slope failure was decreased with increasing slope inclination. An important contribution to the stability of the slope models was provided by the overlapping of the geotextile layers. It has a secondary reinforcement effect when it was prolonged and passed through the shear surface. Moreover, the location of the shear surface observed with PIV analysis exactly matches the tears of the retrieved geotextiles measured carefully after the centrifuge testing. It is concluded that PIV is an efficient tool to instrument the slope failures in a geotechnical centrifuge.(author) [de

  8. Acoustic results of the Boeing model 360 whirl tower test

    Science.gov (United States)

    Watts, Michael E.; Jordan, David

    1990-09-01

    An evaluation is presented for whirl tower test results of the Model 360 helicopter's advanced, high-performance four-bladed composite rotor system intended to facilitate over-200-knot flight. During these performance measurements, acoustic data were acquired by seven microphones. A comparison of whirl-tower tests with theory indicate that theoretical prediction accuracies vary with both microphone position and the inclusion of ground reflection. Prediction errors varied from 0 to 40 percent of the measured signal-to-peak amplitude.

  9. A model based security testing method for protocol implementation.

    Science.gov (United States)

    Fu, Yu Long; Xin, Xiao Long

    2014-01-01

    The security of protocol implementation is important and hard to be verified. Since the penetration testing is usually based on the experience of the security tester and the specific protocol specifications, a formal and automatic verification method is always required. In this paper, we propose an extended model of IOLTS to describe the legal roles and intruders of security protocol implementations, and then combine them together to generate the suitable test cases to verify the security of protocol implementation.

  10. Modélisation du procédé de soudage hybride Arc / Laser par une approche level set application aux toles d'aciers de fortes épaisseurs A level-set approach for the modelling of hybrid arc/laser welding process application for high thickness steel sheets joining

    Directory of Open Access Journals (Sweden)

    Desmaison Olivier

    2013-11-01

    Full Text Available Le procédé de soudage hybride Arc/Laser est une solution aux assemblages difficiles de tôles de fortes épaisseurs. Ce procédé innovant associe deux sources de chaleur : un arc électrique produit par une torche MIG et une source laser placée en amont. Ce couplage améliore le rendement du procédé, la qualité du cordon et les déformations finales. La modélisation de ce procédé par une approche Level Set permet une prédiction du développement du cordon et du champ de température associé. La simulation du soudage multi-passes d'une nuance d'acier 18MnNiMo5 est présentée ici et les résultats sont comparés aux observations expérimentales. The hybrid arc/laser welding process has been developed in order to overcome the difficulties encountered for joining high thickness steel sheets. This innovative process gathers two heat sources: an arc source developed by a MIG torch and a pre-located laser source. This coupling improves the efficiency of the process, the weld bead quality and the final deformations. The Level-Set approach for the modelling of this process enables the prediction of the weld bead development and the temperature field evolution. The simulation of the multi-passes welding of a 18MnNiMo5 steel grade is detailed and the results are compared to the experimental observations.

  11. Tests on dynamic corrosion by water. Influence of the passage of a heat flux on the corrosion kinetics. pH measurement in water at high temperature; Essais de corrosion dynamique par l'eau. Influence du passage d'un flux thermique sur la cinetique de corrosion. Mesure du pH dans l'eau a haute temperature

    Energy Technology Data Exchange (ETDEWEB)

    Coriou, H.; Grall, L.; Hure, J.; Saint-James, R. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Berthod [Societe Grenobloise d' Etudes et d' Applications Hydrauliques, 38 (France); Le peintre [Centre National de la Recherche Scientifique (CNRS), 38 - Grenoble (France)

    1958-07-01

    The passage of a heat flux through the surface of a metal placed in a corrosive medium influences the rate of corrosion, these being higher than under adiabatic conditions. The apparatus developed for corrosion tests is described, it is possible to obtain with this equipment: 1) Heat fluxes greater than 200 W/cm{sup 2}, across aluminium canning, which is cooled by water (temperature 50 deg. C), circulating with flow rates of the order of 5 to 6 m/s. 2) Heat fluxes which can go up to 150 W/cm{sup 2}, across canning of zircaloy or stainless steel. The cooling fluid is pressurized water at a temperature around 280 deg. C, the flow-rate of circulation reaching 6 m/s. The results obtained on aluminium canning are studied from the viewpoint of corrosion, paying particular attention to cavitation phenomena which can cause serious damage in certain special circumstances. After developing a glass electrode system capable of supporting high pressures, the authors have investigated materials capable of functioning as a hydrogen electrode and of resisting satisfactorily corrosion by water at 200 deg. C. Various possibilities have been examined: electrodes of special glasses, quartz, metals, with a membrane etc... The results of the various tests and the practical limits of utilisation are given. (author)Fren. [French] Le passage d'un flux thermique a travers la surface d'un metal place dans un milieu corrosif influence les vitesses de corrosion, celles-ci etant plus elevees que dans des conditions adiabatiques. On decrit les appareils mis au point, pour essais de corrosion. Ils permettent d'obtenir: 1) A travers des gaine aluminium des flux thermiques depassant 200 W /cm{sup 2}. Les gaines sont refroidies par l'eau (temperature 50 deg. C), circulant a des vitesses de l'ordre de 5 a 6 m/s. 2) A travers des gaines en zircaloy ou acier inoxydable des flux thermiques pouvant s'elever a 150 W/cm{sup 2}. Le fluide de refroidissement est de l

  12. Tests on dynamic corrosion by water. Influence of the passage of a heat flux on the corrosion kinetics. pH measurement in water at high temperature; Essais de corrosion dynamique par l'eau. Influence du passage d'un flux thermique sur la cinetique de corrosion. Mesure du pH dans l'eau a haute temperature

    Energy Technology Data Exchange (ETDEWEB)

    Coriou, H; Grall, L; Hure, J; Saint-James, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Berthod, [Societe Grenobloise d' Etudes et d' Applications Hydrauliques, 38 (France); peintre, Le [Centre National de la Recherche Scientifique (CNRS), 38 - Grenoble (France)

    1958-07-01

    The passage of a heat flux through the surface of a metal placed in a corrosive medium influences the rate of corrosion, these being higher than under adiabatic conditions. The apparatus developed for corrosion tests is described, it is possible to obtain with this equipment: 1) Heat fluxes greater than 200 W/cm{sup 2}, across aluminium canning, which is cooled by water (temperature 50 deg. C), circulating with flow rates of the order of 5 to 6 m/s. 2) Heat fluxes which can go up to 150 W/cm{sup 2}, across canning of zircaloy or stainless steel. The cooling fluid is pressurized water at a temperature around 280 deg. C, the flow-rate of circulation reaching 6 m/s. The results obtained on aluminium canning are studied from the viewpoint of corrosion, paying particular attention to cavitation phenomena which can cause serious damage in certain special circumstances. After developing a glass electrode system capable of supporting high pressures, the authors have investigated materials capable of functioning as a hydrogen electrode and of resisting satisfactorily corrosion by water at 200 deg. C. Various possibilities have been examined: electrodes of special glasses, quartz, metals, with a membrane etc... The results of the various tests and the practical limits of utilisation are given. (author)Fren. [French] Le passage d'un flux thermique a travers la surface d'un metal place dans un milieu corrosif influence les vitesses de corrosion, celles-ci etant plus elevees que dans des conditions adiabatiques. On decrit les appareils mis au point, pour essais de corrosion. Ils permettent d'obtenir: 1) A travers des gaine aluminium des flux thermiques depassant 200 W /cm{sup 2}. Les gaines sont refroidies par l'eau (temperature 50 deg. C), circulant a des vitesses de l'ordre de 5 a 6 m/s. 2) A travers des gaines en zircaloy ou acier inoxydable des flux thermiques pouvant s'elever a 150 W/cm{sup 2}. Le fluide de refroidissement est de l'eau sous pression a une temperature

  13. Bayes Factor Covariance Testing in Item Response Models.

    Science.gov (United States)

    Fox, Jean-Paul; Mulder, Joris; Sinharay, Sandip

    2017-12-01

    Two marginal one-parameter item response theory models are introduced, by integrating out the latent variable or random item parameter. It is shown that both marginal response models are multivariate (probit) models with a compound symmetry covariance structure. Several common hypotheses concerning the underlying covariance structure are evaluated using (fractional) Bayes factor tests. The support for a unidimensional factor (i.e., assumption of local independence) and differential item functioning are evaluated by testing the covariance components. The posterior distribution of common covariance components is obtained in closed form by transforming latent responses with an orthogonal (Helmert) matrix. This posterior distribution is defined as a shifted-inverse-gamma, thereby introducing a default prior and a balanced prior distribution. Based on that, an MCMC algorithm is described to estimate all model parameters and to compute (fractional) Bayes factor tests. Simulation studies are used to show that the (fractional) Bayes factor tests have good properties for testing the underlying covariance structure of binary response data. The method is illustrated with two real data studies.

  14. Comparison of transient PCRV model test results with analysis

    International Nuclear Information System (INIS)

    Marchertas, A.H.; Belytschko, T.B.

    1979-01-01

    Comparisons are made of transient data derived from simple models of a reactor containment vessel with analytical solutions. This effort is a part of the ongoing process of development and testing of the DYNAPCON computer code. The test results used in these comparisons were obtained from scaled models of the British sodium cooled fast breeder program. The test structure is a scaled model of a cylindrically shaped reactor containment vessel made of concrete. This concrete vessel is prestressed axially by holddown bolts spanning the top and bottom slabs along the cylindrical walls, and is also prestressed circumferentially by a number of cables wrapped around the vessel. For test purposes this containment vessel is partially filled with water, which comes in direct contact with the vessel walls. The explosive charge is immersed in the pool of water and is centrally suspended from the top of the vessel. The tests are very similar to the series of tests made for the COVA experimental program, but the vessel here is the prestressed concrete container. (orig.)

  15. Ultimate load model test for Sizewell 'B' primary containment

    International Nuclear Information System (INIS)

    Crowder, R.

    1988-01-01

    This paper considers the factors influencing the adoption of an ultimate load factor for the Sizewell 'B' PWR primary containment structure. As part of the validation process for the ultimate load analysis method, a proposal has been made by Nuclear Design Associates to build and test a 1/10th scale model of the containment structure, which would proceed following the granting of section 2 consent for Sizewell 'B'. The modelling principles, construction method and test proposals are examined in some detail. The proposal is currently being considered by the CEGB's Project Management Team. (author)

  16. Delay model and performance testing for FPGA carry chain TDC

    International Nuclear Information System (INIS)

    Kang Xiaowen; Liu Yaqiang; Cui Junjian Yang Zhangcan; Jin Yongjie

    2011-01-01

    Time-of-flight (TOF) information would improve the performance of PET (position emission tomography). TDC design is a key technique. It proposed Carry Chain TDC Delay model. Through changing the significant delay parameter of model, paper compared the difference of TDC performance, and finally realized Time-to-Digital Convertor (TDC) based on Carry Chain Method using FPGA EP2C20Q240C8N with 69 ps LSB, max error below 2 LSB. Such result could meet the TOF demand. It also proposed a Coaxial Cable Measuring method for TDC testing, without High-precision test equipment. (authors)

  17. Model-based automated testing of critical PLC programs.

    CERN Document Server

    Fernández Adiego, B; Tournier, J-C; González Suárez, V M; Bliudze, S

    2014-01-01

    Testing of critical PLC (Programmable Logic Controller) programs remains a challenging task for control system engineers as it can rarely be automated. This paper proposes a model based approach which uses the BIP (Behavior, Interactions and Priorities) framework to perform automated testing of PLC programs developed with the UNICOS (UNified Industrial COntrol System) framework. This paper defines the translation procedure and rules from UNICOS to BIP which can be fully automated in order to hide the complexity of the underlying model from the control engineers. The approach is illustrated and validated through the study of a water treatment process.

  18. Simulation of thermohydraulic phenomena and model test for FBR

    International Nuclear Information System (INIS)

    Satoh, Kazuziro

    1994-01-01

    This paper summarizes the major thermohydraulic phenomena of FBRs and the conventional ways of their model tests, and introduces the recent findings regarding measurement technology and computational science. In the future commercial stage of FBRs, the design optimization will becomes important to improve economy and safety more and more. It is indispensable to use computational science to the plant design and safety evaluation. The most of the model tests will be replaced by the simulation analyses based on computational science. The measurement technology using ultrasonic and the numerical simulation with super parallel computing are considered to be the key technology to realize the design by analysis method. (author)

  19. Le Developmental Entrepreneurship Program du Massachusetts ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Faire en sorte que les étudiants venant des pays en développement pour étudier au MIT retournent ensuite dans leurs pays respectifs afin d'y concrétiser leurs idées est un souci majeur du MIT, des bailleurs de fonds et du milieu du développement. Ce projet palliera à ce souci en soutenant la formation des fellows du ...

  20. Quantification de la Charge Virale et tests de résistance du VIH-1 aux ARV à partir d’échantillons DBS (Dried Blood Spots chez des patients Guinéens sous traitement antirétroviral

    Directory of Open Access Journals (Sweden)

    Nestor Bangoura

    2015-06-01

    Full Text Available Problématique: Comme dans plusieurs pays du Sud, le suivi virologique des patients sous traitement antirétroviral (TARV en Guinée est timide voire inexistant dans certaines localités. Le but de cette étude était d’évaluer la faisabilité technique et logistique de l’utilisation des DBS dans les tests de charge virale (CV et de génotypage. Méthode: De septembre à octobre 2010, les DBS ont été préparés à partir de prélèvements sanguins de patients adultes sous TARV. Le délai d’envoi des échantillons au laboratoire de référence était de 30 jours maximum après le prélèvement et se faisait à température ambiante. La CV a été quantifiée et les échantillons de patients en échec virologique (CV ≥ 3 log10 copies/mL ont été génotypés selon le protocole de l’ANRS. L’algorithme de Stanford version 6.0.8 a été utilisé pour l’analyse et l’interprétation des mutations de résistance. Résultats: Parmi les 136 patients inclus, 129 et 7 étaient respectivement sous première et deuxième ligne de traitement avec une médiane de suivi de 35 mois [IQR: 6-108]. L’échec virologique a été noté chez 33 patients. Parmi eux, 84.8% (n = 28/33 ont bénéficié d’ungénotypage. Le taux de résistance global était de 14% (n = 19/136. Le CRF02_AG était le sous type viral le plus prévalent (82%; n = 23. Conclusion: En plus de montrer la faisabilité technique et logistique des tests de CV et de génotypage à partir des DBS, ces résultats montrent l’intérêt de leurs utilisations dans le suivi virologique des patients sous TARV. Cette étude a permis également de documenter l’échec virologique, la résistance aux ARV et la diversité génétique du VIH-1 en Guinée. Mots clés: VIH-1, Résistance aux ARV, DBS (Dried Blood Spots, Guinée Conakry, Génotypage,Charge Virale.   Quantification of Viral load and resistance tests of HIV-1 to ARVs from dried blood spotssamples in Guinean patients undergoing

  1. Testing and Modeling of Contact Problems in Resistance Welding

    DEFF Research Database (Denmark)

    Song, Quanfeng

    together two or three cylindrical parts as well as disc-ring pairs of dissimilar metals. The tests have demonstrated the effectiveness of the model. A theoretical and experimental study is performed on the contact resistance aiming at a more reliable model for numerical simulation of resistance welding......As a part of the efforts towards a professional and reliable numerical tool for resistance welding engineers, this Ph.D. project is dedicated to refining the numerical models related to the interface behavior. An FE algorithm for the contact problems in resistance welding has been developed...... for the formulation, and the interfaces are treated in a symmetric pattern. The frictional sliding contact is also solved employing the constant friction model. The algorithm is incorporated into the finite element code. Verification is carried out in some numerical tests as well as experiments such as upsetting...

  2. Mechanical test of the model coil wound with large conductor

    International Nuclear Information System (INIS)

    Hiue, Hisaaki; Sugimoto, Makoto; Nakajima, Hideo; Yasukawa, Yukio; Yoshida, Kiyoshi; Hasegawa, Mitsuru; Ito, Ikuo; Konno, Masayuki.

    1992-09-01

    The high rigidity and strength of the winding pack are required to realize the large superconducting magnet for the fusion reactor. This paper describes mechanical tests concerning the rigidity of the winding pack. Samples were prepared to evaluate the adhesive strength between conductors and insulators. Epoxy and Bismaleimide-Triazine resin (BT resin) were used as the conductor insulator. The stainless steel (SS) 304 bars, whose surface was treated mechanically and chemically, was applied to the modeled conductor. The model coil was would with the model conductors covered with the insulator by grand insulator. A winding model combining 3 x 3 conductors was produced for measuring shearing rigidity. The sample was loaded with pure shearing force at the LN 2 temperature. The bar winding sample, by 8 x 6 conductors, was measured the bending rigidity. These three point bending tests were carried out at room temperature. The pancake winding sample was loaded with compressive forces to measure compressive rigidity of winding. (author)

  3. Summary of Numerical Modeling for Underground Nuclear Test Monitoring Symposium

    International Nuclear Information System (INIS)

    Taylor, S.R.; Kamm, J.R.

    1993-01-01

    This document contains the Proceedings of the Numerical Modeling for Underground Nuclear Test Monitoring Symposium held in Durango, Colorado on March 23-25, 1993. The symposium was sponsored by the Office of Arms Control and Nonproliferation of the United States Department of Energy and hosted by the Source Region Program of Los Alamos National Laboratory. The purpose of the meeting was to discuss state-of-the-art advances in numerical simulations of nuclear explosion phenomenology for the purpose of test ban monitoring. Another goal of the symposium was to promote discussion between seismologists and explosion source-code calculators. Presentation topics include the following: numerical model fits to data, measurement and characterization of material response models, applications of modeling to monitoring problems, explosion source phenomenology, numerical simulations and seismic sources

  4. Manufacture and mechanical test of a TORE SUPRA model coil

    International Nuclear Information System (INIS)

    Aymar, R.; Claudet, G.; Disdier, F.; Hamelin, J.; Libeyre, P.; Mayaux, G.; Meuris, C.; Parain, J.; Torossian, A.

    1980-09-01

    Inside the qualifying test programme, supporting the Tore Supra Design, a reduced scale model of a Bsub(T) coil was fabricated by a large industrial firm. This model coil is provided with the same features as those retained for the complete magnet. Tests of this model coil have been carried out in such a way that most of stresses which will arise in Tore Supra windings are simulated; simultaneously its cryogenic supply is fully representative of the system retained for the complete machine. Operation of the model coil has been found highly stable; under the conditions of applied field and forces a coil transition could be triggered, by an electrical heater located inside the coil, only when the temperature of the superfluid helium bath was close to Tsub(lambda). Thus, design and manufacturing techniques have been qualified satisfactorily to proceed to the next step: fabrication of the superconducting Bsub(T) coils of Tore Supra

  5. Les dispositifs du Net art

    OpenAIRE

    Fourmentraux, Jean-Paul

    2010-01-01

    La pratique du Net art radicalise la question du potentiel communicationnel d’un média —Internet— qui constitue tout à la fois le support technique, l’outil créatif et le dispositif social de l’œuvre. Les technologies de l’information et de la communication (TIC) placent en effet l’œuvre d’art au cœur d’une négociation socialement distribuée entre l’artiste et le public. L’article est focalisé sur cette construction collective du Net art et sur ses mises en scènes. Il montre le travail artist...

  6. Stochastic models for strength of wind turbine blades using tests

    DEFF Research Database (Denmark)

    Toft, H.S.; Sørensen, John Dalsgaard

    2008-01-01

    The structural cost of wind turbine blades is dependent on the values of the partial safety factors which reflect the uncertainties in the design values, including statistical uncertainty from a limited number of tests. This paper presents a probabilistic model for ultimate and fatigue strength...... of wind turbine blades especially considering the influence of prior knowledge and test results and how partial safety factors can be updated when additional full-scale tests are performed. This updating is performed by adopting a probabilistic design basis based on Bayesian statistical methods....

  7. Estimation for a Weibull accelerated life testing model

    International Nuclear Information System (INIS)

    Glaser, R.E.

    1984-01-01

    It is sometimes reasonable to assume that the lifetime distribution of an item belongs to a certain parametric family, and that actual parameter values depend upon the testing environment of the item. In the two-parameter Weibull family setting, suppose both the shape and scale parameters are expressible as functions of the testing environment. For various models of functional dependency on environment, maximum likelihood methods are used to estimate characteristics of interest at specified environmental levels. The methodology presented handles exact, censored, and grouped data. A detailed accelerated life testing analysis of stress-rupture data for Kevlar/epoxy composites is given. 10 references, 1 figure, 2 tables

  8. A Human Capital Model of Educational Test Scores

    DEFF Research Database (Denmark)

    McIntosh, James; D. Munk, Martin

    Latent class Poisson count models are used to analyze a sample of Danish test score results from a cohort of individuals born in 1954-55 and tested in 1968. The procedure takes account of unobservable effects as well as excessive zeros in the data. The bulk of unobservable effects are uncorrelated...... with observable parental attributes and, thus, are environmental rather than genetic in origin. We show that the test scores measure manifest or measured ability as it has evolved over the life of the respondent and is, thus, more a product of the human capital formation process than some latent or fundamental...... measure of pure cognitive ability. We find that variables which are not closely associated with traditional notions of intelligence explain a significant proportion of the variation in test scores. This adds to the complexity of interpreting test scores and suggests that school culture, attitudes...

  9. Elevated Temperature Tensile Tests on DU–10Mo Rolled Foils

    Energy Technology Data Exchange (ETDEWEB)

    Schulthess, Jason [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2014-09-01

    Tensile mechanical properties for uranium-10 wt.% molybdenum (U–10Mo) foils are required to support modeling and qualification of new monolithic fuel plate designs. It is expected that depleted uranium-10 wt% Mo (DU–10Mo) mechanical behavior is representative of the low enriched U–10Mo to be used in the actual fuel plates, therefore DU-10Mo was studied to simplify material processing, handling, and testing requirements. In this report, tensile testing of DU-10Mo fuel foils prepared using four different thermomechanical processing treatments were conducted to assess the impact of foil fabrication history on resultant tensile properties.

  10. Polynomial model inversion control: numerical tests and applications

    OpenAIRE

    Novara, Carlo

    2015-01-01

    A novel control design approach for general nonlinear systems is described in this paper. The approach is based on the identification of a polynomial model of the system to control and on the on-line inversion of this model. Extensive simulations are carried out to test the numerical efficiency of the approach. Numerical examples of applicative interest are presented, concerned with control of the Duffing oscillator, control of a robot manipulator and insulin regulation in a type 1 diabetic p...

  11. Testing exact rational expectations in cointegrated vector autoregressive models

    DEFF Research Database (Denmark)

    Johansen, Søren; Swensen, Anders Rygh

    1999-01-01

    This paper considers the testing of restrictions implied by rational expectations hypotheses in a cointegrated vector autoregressive model for I(1) variables. If the rational expectations involve one-step-ahead observations only and the coefficients are known, an explicit parameterization...... of the restrictions is found, and the maximum-likelihood estimator is derived by regression and reduced rank regression. An application is given to a present value model....

  12. Numerical modelling of concentrated leak erosion during Hole Erosion Tests

    OpenAIRE

    Mercier, F.; Bonelli, S.; Golay, F.; Anselmet, F.; Philippe, P.; Borghi, R.

    2015-01-01

    This study focuses on the numerical modelling of concentrated leak erosion of a cohesive soil by a turbulent flow in axisymmetrical geometry, with application to the Hole Erosion Test (HET). The numerical model is based on adaptive remeshing of the water/soil interface to ensure accurate description of the mechanical phenomena occurring near the soil/water interface. The erosion law governing the interface motion is based on two erosion parameters: the critical shear stress and the erosion co...

  13. Building and testing models with extended Higgs sectors

    Science.gov (United States)

    Ivanov, Igor P.

    2017-07-01

    Models with non-minimal Higgs sectors represent a mainstream direction in theoretical exploration of physics opportunities beyond the Standard Model. Extended scalar sectors help alleviate difficulties of the Standard Model and lead to a rich spectrum of characteristic collider signatures and astroparticle consequences. In this review, we introduce the reader to the world of extended Higgs sectors. Not pretending to exhaustively cover the entire body of literature, we walk through a selection of the most popular examples: the two- and multi-Higgs-doublet models, as well as singlet and triplet extensions. We will show how one typically builds models with extended Higgs sectors, describe the main goals and the challenges which arise on the way, and mention some methods to overcome them. We will also describe how such models can be tested, what are the key observables one focuses on, and illustrate the general strategy with a subjective selection of results.

  14. Animal models for dengue vaccine development and testing.

    Science.gov (United States)

    Na, Woonsung; Yeom, Minjoo; Choi, Il-Kyu; Yook, Heejun; Song, Daesub

    2017-07-01

    Dengue fever is a tropical endemic disease; however, because of climate change, it may become a problem in South Korea in the near future. Research on vaccines for dengue fever and outbreak preparedness are currently insufficient. In addition, because there are no appropriate animal models, controversial results from vaccine efficacy assessments and clinical trials have been reported. Therefore, to study the mechanism of dengue fever and test the immunogenicity of vaccines, an appropriate animal model is urgently needed. In addition to mouse models, more suitable models using animals that can be humanized will need to be constructed. In this report, we look at the current status of model animal construction and discuss which models require further development.

  15. L'administration du travail et la production du droit du travail (1906-1960). : Note de synthèse du rapport de recherche

    OpenAIRE

    Le Crom , Jean-Pierre

    2007-01-01

    Synthèse d'un rapport de recherche dont l'objectif est d'appréhender le rôle de l'administration centrale du travail dans la production du droit du travail. Deux dimensions sont explorées : le profil des rédacteurs et l'organisation des structures.

  16. Proton Exchange Membrane Fuel Cell Engineering Model Powerplant. Test Report: Benchmark Tests in Three Spatial Orientations

    Science.gov (United States)

    Loyselle, Patricia; Prokopius, Kevin

    2011-01-01

    Proton exchange membrane (PEM) fuel cell technology is the leading candidate to replace the aging alkaline fuel cell technology, currently used on the Shuttle, for future space missions. This test effort marks the final phase of a 5-yr development program that began under the Second Generation Reusable Launch Vehicle (RLV) Program, transitioned into the Next Generation Launch Technologies (NGLT) Program, and continued under Constellation Systems in the Exploration Technology Development Program. Initially, the engineering model (EM) powerplant was evaluated with respect to its performance as compared to acceptance tests carried out at the manufacturer. This was to determine the sensitivity of the powerplant performance to changes in test environment. In addition, a series of tests were performed with the powerplant in the original standard orientation. This report details the continuing EM benchmark test results in three spatial orientations as well as extended duration testing in the mission profile test. The results from these tests verify the applicability of PEM fuel cells for future NASA missions. The specifics of these different tests are described in the following sections.

  17. Leaching of saltstone: Laboratory and field testing and mathematical modeling

    International Nuclear Information System (INIS)

    Grant, M.W.; Langton, C.A.; Oblath, S.B.; Pepper, D.W.; Wallace, R.M.; Wilhite, E.L.; Yau, W.W.F.

    1987-01-01

    A low-level alkaline salt solution will be a byproduct in the processing of high-level waste at the Savannah River Plant (SRP). This solution will be incorporated into a wasteform, saltstone, and disposed of in surface vaults. Laboratory and field leach testing and mathematical modeling have demonstrated the predictability of contaminant release from cement wasteforms. Saltstone disposal in surface vaults will meet the design objective, which is to meet drinking water standards in shallow groundwater at the disposal area boundary. Diffusion is the predominant mechanism for release of contaminants to the environment. Leach testing in unsaturated soil, at soil moisture levels above 1 wt %, has shown no difference in leach rate compared to leaching in distilled water. Field leach testing of three thirty-ton blocks of saltstone in lysimeters has been underway since January 1984. Mathematical models were applied to assess design features for saltstone disposal. One dimensional infinite-composite and semi-infinite analytical models were developed for assessing diffusion of nitrate from saltstone through a cement barrier. Numerical models, both finite element and finite difference, were validated by comparison of model predictions with the saltstone lysimeter results. Validated models were used to assess the long-term performance of the saltstone stored in surface vaults. The maximum concentrations of all contaminants released from saltstone to shallow groundwater are predicted to be below drinking water standards at the disposal area boundary. 5 refs., 11 figs., 5 tabs

  18. Response of shallow geothermal energy pile from laboratory model tests

    Science.gov (United States)

    Marto, A.; Amaludin, A.

    2015-09-01

    In shallow geothermal energy pile systems, the thermal loads from the pile, transferred and stored in the soil will cause thermally induced settlement. This factor must be considered in the geotechnical design process to avoid unexpected hazards. Series of laboratory model tests were carried out to study the behaviour of energy piles installed in kaolin soil, subjected to thermal loads and a combination of axial and thermal loads (henceforth known as thermo-axial loads). Six tests which included two thermal load tests (35°C and 40°C) and four thermo-axial load tests (100 N and 200 N, combined with 35°C and 40°C thermal loads) were conducted. To simulate the behaviour of geothermal energy piles during its operation, the thermo-axial tests were carried out by applying an axial load to the model pile head, and a subsequent application of thermal load. The model soil was compacted at 90% maximum dry density and had an undrained shear strength of 37 kPa, thus classified as having a firm soil consistency. The behaviour of model pile, having the ultimate load capacity of 460 N, was monitored using a linear variable displacement transducer, load cell and wire thermocouple, to measure the pile head settlement, applied axial load and model pile temperature. The acquired data from this study was used to define the thermo-axial response characteristics of the energy pile model. In this study, the limiting settlement was defined as 10% of the model pile diameter. For thermal load tests, higher thermal loads induced higher values of thermal settlement. At 40°C thermal load an irreversible settlement was observed after the heating and cooling cycle was applied to the model pile. Meanwhile, the pile response to thermo-axial loads were attributed to soil consistency and the magnitude of both the axial and thermal loads applied to the pile. The higher the thermoaxial loads, the higher the settlements occurred. A slight hazard on the model pile was detected, since the settlement

  19. Model Test Bed for Evaluating Wave Models and Best Practices for Resource Assessment and Characterization

    Energy Technology Data Exchange (ETDEWEB)

    Neary, Vincent Sinclair [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Water Power Technologies; Yang, Zhaoqing [Pacific Northwest National Lab. (PNNL), Richland, WA (United States). Coastal Sciences Division; Wang, Taiping [Pacific Northwest National Lab. (PNNL), Richland, WA (United States). Coastal Sciences Division; Gunawan, Budi [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Water Power Technologies; Dallman, Ann Renee [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Water Power Technologies

    2016-03-01

    A wave model test bed is established to benchmark, test and evaluate spectral wave models and modeling methodologies (i.e., best practices) for predicting the wave energy resource parameters recommended by the International Electrotechnical Commission, IEC TS 62600-101Ed. 1.0 ©2015. Among other benefits, the model test bed can be used to investigate the suitability of different models, specifically what source terms should be included in spectral wave models under different wave climate conditions and for different classes of resource assessment. The overarching goal is to use these investigations to provide industry guidance for model selection and modeling best practices depending on the wave site conditions and desired class of resource assessment. Modeling best practices are reviewed, and limitations and knowledge gaps in predicting wave energy resource parameters are identified.

  20. A General Model for Testing Mediation and Moderation Effects

    Science.gov (United States)

    MacKinnon, David P.

    2010-01-01

    This paper describes methods for testing mediation and moderation effects in a dataset, both together and separately. Investigations of this kind are especially valuable in prevention research to obtain information on the process by which a program achieves its effects and whether the program is effective for subgroups of individuals. A general model that simultaneously estimates mediation and moderation effects is presented, and the utility of combining the effects into a single model is described. Possible effects of interest in the model are explained, as are statistical methods to assess these effects. The methods are further illustrated in a hypothetical prevention program example. PMID:19003535

  1. Precision tests of quantum chromodynamics and the standard model

    International Nuclear Information System (INIS)

    Brodsky, S.J.; Lu, H.J.

    1995-06-01

    The authors discuss three topics relevant to testing the Standard Model to high precision: commensurate scale relations, which relate observables to each other in perturbation theory without renormalization scale or scheme ambiguity, the relationship of compositeness to anomalous moments, and new methods for measuring the anomalous magnetic and quadrupole moments of the W and Z

  2. Modelling and simulation of eddy current non-destructive testing

    International Nuclear Information System (INIS)

    Mansir, H.; Burais, N.; Nicolas, A.

    1986-01-01

    This paper presents the practical configuration for detecting cracks in conducting materials by eddy current non destructive testing. An electromagnetic field formulation is proposed using Maxwell's relations. Geometrical and physical properties of the crack are taken into account by several models, particularly with a new finite element called ''crack element''. Modelisation is applied to sensor impedance calculation with classical numerical methods [fr

  3. A Test Procedure for Determining Models of LV Equipment

    NARCIS (Netherlands)

    Cuk, Vladimir; Cobben, Joseph F.G.; Kling, Wil L.; Timens, R.B.; Leferink, Frank Bernardus Johannes

    2009-01-01

    An automated test technique for determining parameters of low voltage equipment is presented in the paper. The aim of this research is to obtain simple models of household, office and industrial equipment which could be used to predict power quality problems during the design of low voltage

  4. Kolmogorov complexity, pseudorandom generators and statistical models testing

    Czech Academy of Sciences Publication Activity Database

    Šindelář, Jan; Boček, Pavel

    2002-01-01

    Roč. 38, č. 6 (2002), s. 747-759 ISSN 0023-5954 R&D Projects: GA ČR GA102/99/1564 Institutional research plan: CEZ:AV0Z1075907 Keywords : Kolmogorov complexity * pseudorandom generators * statistical models testing Subject RIV: BB - Applied Statistics, Operational Research Impact factor: 0.341, year: 2002

  5. Measuring damage in physical model tests of rubble mounds

    NARCIS (Netherlands)

    Hofland, B.; Rosa-Santos, Paulo; Taveira-Pinto, Francisco; Lemos, Rute; Mendonça, A.; Juana Fortes, C

    2017-01-01

    This paper studies novel ways to evaluate armour damage in physical models of coastal structures. High-resolution damage data for reference rubble mound breakwaters obtained under the HYDRALAB+ joint-research project are analysed and discussed. These tests are used to analyse the way to describe

  6. Goodness-of-fit tests in mixed models

    KAUST Repository

    Claeskens, Gerda; Hart, Jeffrey D.

    2009-01-01

    Mixed models, with both random and fixed effects, are most often estimated on the assumption that the random effects are normally distributed. In this paper we propose several formal tests of the hypothesis that the random effects and/or errors

  7. Item Response Theory Modeling of the Philadelphia Naming Test

    Science.gov (United States)

    Fergadiotis, Gerasimos; Kellough, Stacey; Hula, William D.

    2015-01-01

    Purpose: In this study, we investigated the fit of the Philadelphia Naming Test (PNT; Roach, Schwartz, Martin, Grewal, & Brecher, 1996) to an item-response-theory measurement model, estimated the precision of the resulting scores and item parameters, and provided a theoretical rationale for the interpretation of PNT overall scores by relating…

  8. Numerical modeling of the Near Surface Test Facility No. 1 and No. 2 heater tests

    International Nuclear Information System (INIS)

    Hocking, G.; Williams, J.; Boonlualohr, P.; Mathews, I.; Mustoe, G.

    1981-01-01

    Thermomechanical predictive calculations have been undertaken for two full scale heater tests No. 1 and No. 2 at the Near Surface Test Facility (NSTF) at Hanford, Washington. Numerical predictions were made of the basaltic rock response involving temperatures, displacements, strains and stresses due to energizing the electrical heaters. The basalt rock mass was modeled as an isotropic thermal material but with temperature dependent thermal conductivity, specific heat and thermal expansion. The fractured nature of the basalt necessitated that it be modeled as a cross anisotropic medium with a bi-linear locking stress strain relationship. The cross-anisotropic idealization was selected after characterization studies indicated that a vertical columnar structure persisted throughout the test area and no major throughgoing discontinuities were present. The deformational properties were determined from fracture frequency and orientation, joint deformational data, Goodman Jack results and two rock mass classification schemes. Similar deformational moduli were determined from these techniques, except for the Goodman Jack results. The finite element technique was utilized for both the non-linear thermal and mechanical computations. An incremental stiffness method with residual force correction was employed to solve the non-linear problem by piecewise linearization. Two and three dimensional thermomechanical scoping calculations were made to assess the significance of various parameters and associated errors with geometrical idealizations. Both heater tests were modeled as two dimensional axisymmetric geometry with water assumed to be absent. Instrument response was predicted for all of the thermocouples, extensometers, USBM borehole deformation and IRAD gages for the entire duration of both tests

  9. Stochastic order in dichotomous item response models for fixed tests, research adaptive tests, or multiple abilities

    NARCIS (Netherlands)

    van der Linden, Willem J.

    1995-01-01

    Dichotomous item response theory (IRT) models can be viewed as families of stochastically ordered distributions of responses to test items. This paper explores several properties of such distributiom. The focus is on the conditions under which stochastic order in families of conditional

  10. ExEP yield modeling tool and validation test results

    Science.gov (United States)

    Morgan, Rhonda; Turmon, Michael; Delacroix, Christian; Savransky, Dmitry; Garrett, Daniel; Lowrance, Patrick; Liu, Xiang Cate; Nunez, Paul

    2017-09-01

    EXOSIMS is an open-source simulation tool for parametric modeling of the detection yield and characterization of exoplanets. EXOSIMS has been adopted by the Exoplanet Exploration Programs Standards Definition and Evaluation Team (ExSDET) as a common mechanism for comparison of exoplanet mission concept studies. To ensure trustworthiness of the tool, we developed a validation test plan that leverages the Python-language unit-test framework, utilizes integration tests for selected module interactions, and performs end-to-end crossvalidation with other yield tools. This paper presents the test methods and results, with the physics-based tests such as photometry and integration time calculation treated in detail and the functional tests treated summarily. The test case utilized a 4m unobscured telescope with an idealized coronagraph and an exoplanet population from the IPAC radial velocity (RV) exoplanet catalog. The known RV planets were set at quadrature to allow deterministic validation of the calculation of physical parameters, such as working angle, photon counts and integration time. The observing keepout region was tested by generating plots and movies of the targets and the keepout zone over a year. Although the keepout integration test required the interpretation of a user, the test revealed problems in the L2 halo orbit and the parameterization of keepout applied to some solar system bodies, which the development team was able to address. The validation testing of EXOSIMS was performed iteratively with the developers of EXOSIMS and resulted in a more robust, stable, and trustworthy tool that the exoplanet community can use to simulate exoplanet direct-detection missions from probe class, to WFIRST, up to large mission concepts such as HabEx and LUVOIR.

  11. Réflexion sur l’origine du processus de segmentation du marche du travail

    Directory of Open Access Journals (Sweden)

    Attia Nicole

    2006-01-01

    Full Text Available (francuski Ce travail propose une réflexion sur l'origine du processus de segmentation du marché du travail par rapport à l'entreprise. Se situe-t-elle au sein même de l'entreprise ou en amont, c'est à dire entre les entreprises? Cela revient à se demander si on peut avoir une approche microéconomique ou macroéconomique de la segmentation et, à s'interroger sur le rôle réel tenu par les firmes dans le processus. Déterminant pour la théorie, ce rôle est à repenser selon la réponse apportée à notre question.

  12. Performance verification tests of JT-60SA CS model coil

    Energy Technology Data Exchange (ETDEWEB)

    Obana, Tetsuhiro, E-mail: obana.tetsuhiro@LHD.nifs.ac.jp [National Institute for Fusion Science, 322-6 Oroshi, Toki, Gifu 509-5292 (Japan); Murakami, Haruyuki [Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan); Takahata, Kazuya; Hamaguchi, Shinji; Chikaraishi, Hirotaka; Mito, Toshiyuki; Imagawa, Shinsaku [National Institute for Fusion Science, 322-6 Oroshi, Toki, Gifu 509-5292 (Japan); Kizu, Kaname; Natsume, Kyohei; Yoshida, Kiyoshi [Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan)

    2015-11-15

    Highlights: • The performance of the JT-60SA CS model coil was verified. • The CS model coil comprised a quad-pancake wound with a Nb{sub 3}Sn CIC conductor. • The CS model coil met the design requirements. - Abstract: As a final check of the coil manufacturing method of the JT-60 Super Advanced (JT-60SA) central solenoid (CS), we verified the performance of a CS model coil. The model coil comprised a quad-pancake wound with a Nb{sub 3}Sn cable-in-conduit conductor. Measurements of the critical current, joint resistance, pressure drop, and magnetic field were conducted in the verification tests. In the critical-current measurement, the critical current of the model coil coincided with the estimation derived from a strain of −0.62% for the Nb{sub 3}Sn strands. As a result, critical-current degradation caused by the coil manufacturing process was not observed. The results of the performance verification tests indicate that the model coil met the design requirements. Consequently, the manufacturing process of the JT-60SA CS was established.

  13. Testing a theoretical model of clinical nurses' intent to stay.

    Science.gov (United States)

    Cowden, Tracy L; Cummings, Greta G

    2015-01-01

    Published theoretical models of nurses' intent to stay (ITS) report inconsistent outcomes, and not all hypothesized models have been adequately tested. Research has focused on cognitive rather than emotional determinants of nurses' ITS. The aim of this study was to empirically verify a complex theoretical model of nurses' ITS that includes both affective and cognitive determinants and to explore the influence of relational leadership on staff nurses' ITS. The study was a correlational, mixed-method, nonexperimental design. A subsample of the Quality Work Environment Study survey data 2009 (n = 415 nurses) was used to test our theoretical model of clinical nurses' ITS as a structural equation model. The model explained 63% of variance in ITS. Organizational commitment, empowerment, and desire to stay were the model concepts with the strongest effects on nurses' ITS. Leadership practices indirectly influenced ITS. How nurses evaluate and respond to their work environment is both an emotional and rational process. Health care organizations need to be cognizant of the influence that nurses' feelings and views of their work setting have on their intention decisions and integrate that knowledge into the development of retention strategies. Leadership practices play an important role in staff nurses' perceptions of the workplace. Identifying the mechanisms by which leadership influences staff nurses' intentions to stay presents additional focus areas for developing retention strategies.

  14. Parametric Thermal Models of the Transient Reactor Test Facility (TREAT)

    Energy Technology Data Exchange (ETDEWEB)

    Bradley K. Heath

    2014-03-01

    This work supports the restart of transient testing in the United States using the Department of Energy’s Transient Reactor Test Facility at the Idaho National Laboratory. It also supports the Global Threat Reduction Initiative by reducing proliferation risk of high enriched uranium fuel. The work involves the creation of a nuclear fuel assembly model using the fuel performance code known as BISON. The model simulates the thermal behavior of a nuclear fuel assembly during steady state and transient operational modes. Additional models of the same geometry but differing material properties are created to perform parametric studies. The results show that fuel and cladding thermal conductivity have the greatest effect on fuel temperature under the steady state operational mode. Fuel density and fuel specific heat have the greatest effect for transient operational model. When considering a new fuel type it is recommended to use materials that decrease the specific heat of the fuel and the thermal conductivity of the fuel’s cladding in order to deal with higher density fuels that accompany the LEU conversion process. Data on the latest operating conditions of TREAT need to be attained in order to validate BISON’s results. BISON’s models for TREAT (material models, boundary convection models) are modest and need additional work to ensure accuracy and confidence in results.

  15. Transgenic Mouse Models Transferred into the Test Tube: New Perspectives for Developmental Toxicity Testing In Vitro?

    Science.gov (United States)

    Kugler, Josephine; Luch, Andreas; Oelgeschläger, Michael

    2016-10-01

    Despite our increasing understanding of molecular mechanisms controlling embryogenesis, the identification and characterization of teratogenic substances still heavily relies on animal testing. Embryonic development depends on cell-autonomous and non-autonomous processes including spatiotemporally regulated extracellular signaling activities. These have been elucidated in transgenic mouse models harboring easily detectable reporter genes under the control of evolutionarily conserved signaling cascades. We propose combining these transgenic mouse models and cells derived thereof with existing alternative toxicological testing strategies. This would enable the plausibility of in vitro data to be verified in light of in vivo data and, ultimately, facilitate regulatory acceptance of in vitro test methods. Copyright © 2016 Elsevier Ltd. All rights reserved.

  16. Test of a model coil of TORE SUPRA

    International Nuclear Information System (INIS)

    Aymar, R.; Claudet, G.; Disdier, F.; Hamelin, J.; Libeyre, P.; Mayaux, C.; Meuris, C.; Parain, J.; Torossian, A.

    1980-10-01

    Inside the qualifying test programme, supporting the 'Tore Supra' Tokamak design, a reduced scale model of coil was fabricated by an industrial firm and fully tested. This model coil is provided with the same features as those retained for the complete magnet and is built according to the same design; in particular the Nb-Ti mixed matrix monolithic conductor is cooled by a pressurized superfluid helium bath, supplied from a model of the envisaged complete cryogenic system. Three main objectives have been assigned to this test: operation of the cryogenic system, stability of the superconductor winding under high mechanical stresses, mainly shear, and simulation of coil quench conditions. For this purpose, the model coil (outside bore 0.8 m) is located inside a 4 T magnet, an hydraulic jack applies a 1 MN force along a coil diameter. Operation of the model coil has been found highly stable, under the conditions of applied field and forces, a coil transition can be induced by an electrical heater only when the superfluid bath temperature is close to Tlambda. The 1.8 K cryogenic system provides a useful calorimetric measure of total losses induced inside the winding; its operation has been quite simple and reliable, permitting a sure extrapolation to a much larger size

  17. Optimum coagulant forecasting by modeling jar test experiments using ANNs

    Science.gov (United States)

    Haghiri, Sadaf; Daghighi, Amin; Moharramzadeh, Sina

    2018-01-01

    Currently, the proper utilization of water treatment plants and optimizing their use is of particular importance. Coagulation and flocculation in water treatment are the common ways through which the use of coagulants leads to instability of particles and the formation of larger and heavier particles, resulting in improvement of sedimentation and filtration processes. Determination of the optimum dose of such a coagulant is of particular significance. A high dose, in addition to adding costs, can cause the sediment to remain in the filtrate, a dangerous condition according to the standards, while a sub-adequate dose of coagulants can result in the reducing the required quality and acceptable performance of the coagulation process. Although jar tests are used for testing coagulants, such experiments face many constraints with respect to evaluating the results produced by sudden changes in input water because of their significant costs, long time requirements, and complex relationships among the many factors (turbidity, temperature, pH, alkalinity, etc.) that can influence the efficiency of coagulant and test results. Modeling can be used to overcome these limitations; in this research study, an artificial neural network (ANN) multi-layer perceptron (MLP) with one hidden layer has been used for modeling the jar test to determine the dosage level of used coagulant in water treatment processes. The data contained in this research have been obtained from the drinking water treatment plant located in Ardabil province in Iran. To evaluate the performance of the model, the mean squared error (MSE) and correlation coefficient (R2) parameters have been used. The obtained values are within an acceptable range that demonstrates the high accuracy of the models with respect to the estimation of water-quality characteristics and the optimal dosages of coagulants; so using these models will allow operators to not only reduce costs and time taken to perform experimental jar tests

  18. Models on reliability of non-destructive testing

    International Nuclear Information System (INIS)

    Simola, K.; Pulkkinen, U.

    1998-01-01

    The reliability of ultrasonic inspections has been studied in e.g. international PISC (Programme for the Inspection of Steel Components) exercises. These exercises have produced a large amount of information on the effect of various factors on the reliability of inspections. The information obtained from reliability experiments are used to model the dependency of flaw detection probability on various factors and to evaluate the performance of inspection equipment, including the sizing accuracy. The information from experiments is utilised in a most effective way when mathematical models are applied. Here, some statistical models for reliability of non-destructive tests are introduced. In order to demonstrate the use of inspection reliability models, they have been applied to the inspection results of intergranular stress corrosion cracking (IGSCC) type flaws in PISC III exercise (PISC 1995). The models are applied to both flaw detection frequency data of all inspection teams and to flaw sizing data of one participating team. (author)

  19. Modeling and Testing of EVs - Preliminary Study and Laboratory Development

    DEFF Research Database (Denmark)

    Yang, Guang-Ya; Marra, Francesco; Nielsen, Arne Hejde

    2010-01-01

    Electric vehicles (EVs) are expected to play a key role in the future energy management system to stabilize both supply and consumption with the presence of high penetration of renewable generation. A reasonably accurate model of battery is a key element for the study of EVs behavior and the grid...... tests, followed by the suggestions towards a feasible battery model for further studies.......Electric vehicles (EVs) are expected to play a key role in the future energy management system to stabilize both supply and consumption with the presence of high penetration of renewable generation. A reasonably accurate model of battery is a key element for the study of EVs behavior and the grid...... impact at different geographical areas, as well as driving and charging patterns. Electric circuit model is deployed in this work to represent the electrical properties of a lithium-ion battery. This paper reports the preliminary modeling and validation work based on manufacturer data sheet and realistic...

  20. Test-Driven, Model-Based Systems Engineering

    DEFF Research Database (Denmark)

    Munck, Allan

    Hearing systems have evolved over many years from simple mechanical devices (horns) to electronic units consisting of microphones, amplifiers, analog filters, loudspeakers, batteries, etc. Digital signal processors replaced analog filters to provide better performance end new features. Central....... This thesis concerns methods for identifying, selecting and implementing tools for various aspects of model-based systems engineering. A comprehensive method was proposed that include several novel steps such as techniques for analyzing the gap between requirements and tool capabilities. The method...... was verified with good results in two case studies for selection of a traceability tool (single-tool scenario) and a set of modeling tools (multi-tool scenarios). Models must be subjected to testing to allow engineers to predict functionality and performance of systems. Test-first strategies are known...

  1. Development and Test of TQC models, LARP Technological Quadrupole Magnets

    Energy Technology Data Exchange (ETDEWEB)

    Bossert, R.C.; Ambrosio, G.; Andreev, N.; Barzi, E.; Carcagno, R.; Feher, S.; Kashikhin, V.S.; Kashikhin, V.V.; Nobrega, F.; Novitski, I.; Orris, D.; Tartaglia, M.; Zlobin, A.V.; Caspi, S.; Dietderich, D.; Ferracin, P.; Hafalia, A.R.; Sabbi, G.

    2008-06-01

    In support of the development of a large-aperture Nb3Sn superconducting quadrupole for the Large Hadron Collider (LHC) luminosity upgrade, two-layer quadrupole models (TQC and TQS) with 90mm aperture are being constructed at Fermilab and LBNL within the framework of the US LHC Accelerator Research Program (LARP). This paper describes the development and test of TQC01b, the second TQC model, and the experience during construction of TQE02 and TQC02, subsequent models in the series. ANSYS analysis of the mechanical structure, its underlying assumptions, and changes based on experience with TQC01 are presented and discussed. Construction experience, in-process measurements, and modifications to the assembly since TQC01 are described. The test results presented here include magnet strain and quench performance during training of TQC01b, as well as quench studies of current ramp rate dependence.

  2. Development and Test of TQC models, LARP Technological Quadrupole Magnets

    International Nuclear Information System (INIS)

    Bossert, R.C.; Ambrosio, G.; Andreev, N.; Barzi, E.; Carcagno, R.; Feher, S.; Kashikhin, V.S.; Kashikhin, V.V.; Nobrega, F.; Novitski, I.; Orris, D.; Tartaglia, M.; Zlobin, A.V.; Caspi, S.; Dietderich, D.; Ferracin, P.; Hafalia, A.R.; Sabbi, G.

    2008-01-01

    In support of the development of a large-aperture Nb3Sn superconducting quadrupole for the Large Hadron Collider (LHC) luminosity upgrade, two-layer quadrupole models (TQC and TQS) with 90mm aperture are being constructed at Fermilab and LBNL within the framework of the US LHC Accelerator Research Program (LARP). This paper describes the development and test of TQC01b, the second TQC model, and the experience during construction of TQE02 and TQC02, subsequent models in the series. ANSYS analysis of the mechanical structure, its underlying assumptions, and changes based on experience with TQC01 are presented and discussed. Construction experience, in-process measurements, and modifications to the assembly since TQC01 are described. The test results presented here include magnet strain and quench performance during training of TQC01b, as well as quench studies of current ramp rate dependence

  3. A blind test on the pulse tube refrigerator model (PTRM)

    International Nuclear Information System (INIS)

    Yuan, S.W.K.; Radebaugh, R.

    1996-01-01

    The Stirling Refrigerator Performance Model (SRPM) has been validated extensively against the Lockheed built Stirling Coolers and various units in the literature. This model has been modified to predict the performance of the Pulse Tube Coolers (PTCs). It was successfully validated against a Lockheed in-house-built PTC. The results are to be published elsewhere. In this paper, the validation of PTRM against a NIST (National Institute of Standards and Technology) orifice pulse tube cooler is reported. Dimensions and operating condition of the PTC were obtained from NIST without prior knowledge of the performance. In other words, this is a open-quote blind test close-quote on the PTRM with the help of the National Institute of Standards and Technology. Good correlation was found between the test data and the prediction. PTRM is a generic model that gives accurate performance prediction of the pulse tube coolers

  4. Carbon Back Sputter Modeling for Hall Thruster Testing

    Science.gov (United States)

    Gilland, James H.; Williams, George J.; Burt, Jonathan M.; Yim, John T.

    2016-01-01

    In support of wear testing for the Hall Effect Rocket with Magnetic Shielding (HERMeS) program, the back sputter from a Hall effect thruster plume has been modeled for the NASA Glenn Research Centers Vacuum Facility 5. The predicted wear at a near-worst case condition of 600 V, 12.5 kW was found to be on the order of 3 4 mkhour in a fully carbon-lined chamber. A more detailed numerical monte carlo code was also modified to estimate back sputter for a detailed facility and pumping configuration. This code demonstrated similar back sputter rate distributions, but is not yet accurately modeling the magnitudes. The modeling has been benchmarked to recent HERMeS wear testing, using multiple microbalance measurements. These recent measurements have yielded values, on the order of 1.5- 2 microns/khour.

  5. Analysing model fit of psychometric process models: An overview, a new test and an application to the diffusion model.

    Science.gov (United States)

    Ranger, Jochen; Kuhn, Jörg-Tobias; Szardenings, Carsten

    2017-05-01

    Cognitive psychometric models embed cognitive process models into a latent trait framework in order to allow for individual differences. Due to their close relationship to the response process the models allow for profound conclusions about the test takers. However, before such a model can be used its fit has to be checked carefully. In this manuscript we give an overview over existing tests of model fit and show their relation to the generalized moment test of Newey (Econometrica, 53, 1985, 1047) and Tauchen (J. Econometrics, 30, 1985, 415). We also present a new test, the Hausman test of misspecification (Hausman, Econometrica, 46, 1978, 1251). The Hausman test consists of a comparison of two estimates of the same item parameters which should be similar if the model holds. The performance of the Hausman test is evaluated in a simulation study. In this study we illustrate its application to two popular models in cognitive psychometrics, the Q-diffusion model and the D-diffusion model (van der Maas, Molenaar, Maris, Kievit, & Boorsboom, Psychol Rev., 118, 2011, 339; Molenaar, Tuerlinckx, & van der Maas, J. Stat. Softw., 66, 2015, 1). We also compare the performance of the test to four alternative tests of model fit, namely the M 2 test (Molenaar et al., J. Stat. Softw., 66, 2015, 1), the moment test (Ranger et al., Br. J. Math. Stat. Psychol., 2016) and the test for binned time (Ranger & Kuhn, Psychol. Test. Asess. , 56, 2014b, 370). The simulation study indicates that the Hausman test is superior to the latter tests. The test closely adheres to the nominal Type I error rate and has higher power in most simulation conditions. © 2017 The British Psychological Society.

  6. Atmospheric resuspension of radionuclides. Model testing using Chernobyl data

    International Nuclear Information System (INIS)

    Garger, E.; Lev, T.; Talerko, N.; Galeriu, D.; Garland, J.; Hoffman, O.; Nair, S.; Thiessen, K.; Miller, C.; Mueller, H.; Kryshev, A.

    1996-10-01

    Resuspension can be an important secondary source of contamination after a release has stopped, as well as a source of contamination for people and areas not exposed to the original release. The inhalation of resuspended radionuclides contributes to the overall dose received by exposed individuals. Based on measurements collected after the Chernobyl accident, Scenario R was developed to provide an opportunity to test existing mathematical models of contamination resuspension. In particular, this scenario provided the opportunity to examine data and test models for atmospheric resuspension of radionuclides at several different locations from the release, to investigate resuspension processes on both local and regional scales, and to investigate the importance of seasonal variations of these processes. Participants in the test exercise were provided with information for three different types of locations: (1) within the 30-km zone, where local resuspension processes are expected to dominate; (2) a large urban location (Kiev) 120 km from the release site, where vehicular traffic is expected to be the dominant mechanism for resuspension; and (3) an agricultural area 40-60 km from the release site, where highly contaminated upwind 'hot spots' are expected to be important. Input information included characteristics of the ground contamination around specific sites, climatological data for the sites, characteristics of the terrain and topography, and locations of the sampling sites. Participants were requested to predict the average (quarterly and yearly) concentrations of 137 Cs in air at specified locations due to resuspension of Chernobyl fallout; predictions for 90 Sr and 239 + 240 Pu were also requested for one location and time point. Predictions for specified resuspension factors and rates were also requested. Most participants used empirical models for the resuspension factor as a function of time K(t), as opposed to process-based models. While many of these

  7. Model- and calibration-independent test of cosmic acceleration

    International Nuclear Information System (INIS)

    Seikel, Marina; Schwarz, Dominik J.

    2009-01-01

    We present a calibration-independent test of the accelerated expansion of the universe using supernova type Ia data. The test is also model-independent in the sense that no assumptions about the content of the universe or about the parameterization of the deceleration parameter are made and that it does not assume any dynamical equations of motion. Yet, the test assumes the universe and the distribution of supernovae to be statistically homogeneous and isotropic. A significant reduction of systematic effects, as compared to our previous, calibration-dependent test, is achieved. Accelerated expansion is detected at significant level (4.3σ in the 2007 Gold sample, 7.2σ in the 2008 Union sample) if the universe is spatially flat. This result depends, however, crucially on supernovae with a redshift smaller than 0.1, for which the assumption of statistical isotropy and homogeneity is less well established

  8. Elevated Temperature Testing and Modeling of Advanced Toughened Ceramic Materials

    Science.gov (United States)

    Keith, Theo G.

    2005-01-01

    The purpose of this report is to provide a final report for the period of 12/1/03 through 11/30/04 for NASA Cooperative Agreement NCC3-776, entitled "Elevated Temperature Testing and Modeling of Advanced Toughened Ceramic Materials." During this final period, major efforts were focused on both the determination of mechanical properties of advanced ceramic materials and the development of mechanical test methodologies under several different programs of the NASA-Glenn. The important research activities made during this period are: 1. Mechanical properties evaluation of two gas-turbine grade silicon nitrides. 2) Mechanical testing for fuel-cell seal materials. 3) Mechanical properties evaluation of thermal barrier coatings and CFCCs and 4) Foreign object damage (FOD) testing.

  9. Comparison of transient PCRV model test results with analysis

    International Nuclear Information System (INIS)

    Marchertas, A.H.; Belytschko, T.B.

    1979-01-01

    Comparisons are made of transient data derived from simple models of a reactor containment vessel with analytical solutions. This effort is a part of the ongoing process of development and testing of the DYNAPCON computer code. The test results used in these comparisons were obtained from scaled models of the British sodium cooled fast breeder program. The test structure is a scaled model of a cylindrically shaped reactor containment vessel made of concrete. This concrete vessel is prestressed axially by holddown bolts spanning the top and bottom slabs along the cylindrical walls, and is also prestressed circumferentially by a number of cables wrapped around the vessel. For test purposes this containment vessel is partially filled with water, which comes in direct contact with the vessel walls. The explosive charge is immersed in the pool of water and is centrally suspended from the top of the vessel. The load history was obtained from an ICECO analysis, using the equations of state for the source and the water. A detailed check of this solution was made to assure that the derived loading did provide the correct input. The DYNAPCON code was then used for the analysis of the prestressed concrete containment model. This analysis required the simulation of prestressing and the response of the model to the applied transient load. The calculations correctly predict the magnitudes of displacements of the PCRV model. In addition, the displacement time histories obtained from the calculations reproduce the general features of the experimental records: the period elongation and amplitude increase as compared to an elastic solution, and also the absence of permanent displacement. However, the period still underestimates the experiment, while the amplitude is generally somewhat large

  10. The Latent Class Model as a Measurement Model for Situational Judgment Tests

    Directory of Open Access Journals (Sweden)

    Frank Rijmen

    2011-11-01

    Full Text Available In a situational judgment test, it is often debatable what constitutes a correct answer to a situation. There is currently a multitude of scoring procedures. Establishing a measurement model can guide the selection of a scoring rule. It is argued that the latent class model is a good candidate for a measurement model. Two latent class models are applied to the Managing Emotions subtest of the Mayer, Salovey, Caruso Emotional Intelligence Test: a plain-vanilla latent class model, and a second-order latent class model that takes into account the clustering of several possible reactions within each hypothetical scenario of the situational judgment test. The results for both models indicated that there were three subgroups characterised by the degree to which differentiation occurred between possible reactions in terms of perceived effectiveness. Furthermore, the results for the second-order model indicated a moderate cluster effect.

  11. A framework for testing and comparing binaural models.

    Science.gov (United States)

    Dietz, Mathias; Lestang, Jean-Hugues; Majdak, Piotr; Stern, Richard M; Marquardt, Torsten; Ewert, Stephan D; Hartmann, William M; Goodman, Dan F M

    2018-03-01

    Auditory research has a rich history of combining experimental evidence with computational simulations of auditory processing in order to deepen our theoretical understanding of how sound is processed in the ears and in the brain. Despite significant progress in the amount of detail and breadth covered by auditory models, for many components of the auditory pathway there are still different model approaches that are often not equivalent but rather in conflict with each other. Similarly, some experimental studies yield conflicting results which has led to controversies. This can be best resolved by a systematic comparison of multiple experimental data sets and model approaches. Binaural processing is a prominent example of how the development of quantitative theories can advance our understanding of the phenomena, but there remain several unresolved questions for which competing model approaches exist. This article discusses a number of current unresolved or disputed issues in binaural modelling, as well as some of the significant challenges in comparing binaural models with each other and with the experimental data. We introduce an auditory model framework, which we believe can become a useful infrastructure for resolving some of the current controversies. It operates models over the same paradigms that are used experimentally. The core of the proposed framework is an interface that connects three components irrespective of their underlying programming language: The experiment software, an auditory pathway model, and task-dependent decision stages called artificial observers that provide the same output format as the test subject. Copyright © 2017 Elsevier B.V. All rights reserved.

  12. Permutation tests for goodness-of-fit testing of mathematical models to experimental data.

    Science.gov (United States)

    Fişek, M Hamit; Barlas, Zeynep

    2013-03-01

    This paper presents statistical procedures for improving the goodness-of-fit testing of theoretical models to data obtained from laboratory experiments. We use an experimental study in the expectation states research tradition which has been carried out in the "standardized experimental situation" associated with the program to illustrate the application of our procedures. We briefly review the expectation states research program and the fundamentals of resampling statistics as we develop our procedures in the resampling context. The first procedure we develop is a modification of the chi-square test which has been the primary statistical tool for assessing goodness of fit in the EST research program, but has problems associated with its use. We discuss these problems and suggest a procedure to overcome them. The second procedure we present, the "Average Absolute Deviation" test, is a new test and is proposed as an alternative to the chi square test, as being simpler and more informative. The third and fourth procedures are permutation versions of Jonckheere's test for ordered alternatives, and Kendall's tau(b), a rank order correlation coefficient. The fifth procedure is a new rank order goodness-of-fit test, which we call the "Deviation from Ideal Ranking" index, which we believe may be more useful than other rank order tests for assessing goodness-of-fit of models to experimental data. The application of these procedures to the sample data is illustrated in detail. We then present another laboratory study from an experimental paradigm different from the expectation states paradigm - the "network exchange" paradigm, and describe how our procedures may be applied to this data set. Copyright © 2012 Elsevier Inc. All rights reserved.

  13. Analysing earthquake slip models with the spatial prediction comparison test

    KAUST Repository

    Zhang, L.; Mai, Paul Martin; Thingbaijam, Kiran Kumar; Razafindrakoto, H. N. T.; Genton, Marc G.

    2014-01-01

    Earthquake rupture models inferred from inversions of geophysical and/or geodetic data exhibit remarkable variability due to uncertainties in modelling assumptions, the use of different inversion algorithms, or variations in data selection and data processing. A robust statistical comparison of different rupture models obtained for a single earthquake is needed to quantify the intra-event variability, both for benchmark exercises and for real earthquakes. The same approach may be useful to characterize (dis-)similarities in events that are typically grouped into a common class of events (e.g. moderate-size crustal strike-slip earthquakes or tsunamigenic large subduction earthquakes). For this purpose, we examine the performance of the spatial prediction comparison test (SPCT), a statistical test developed to compare spatial (random) fields by means of a chosen loss function that describes an error relation between a 2-D field (‘model’) and a reference model. We implement and calibrate the SPCT approach for a suite of synthetic 2-D slip distributions, generated as spatial random fields with various characteristics, and then apply the method to results of a benchmark inversion exercise with known solution. We find the SPCT to be sensitive to different spatial correlations lengths, and different heterogeneity levels of the slip distributions. The SPCT approach proves to be a simple and effective tool for ranking the slip models with respect to a reference model.

  14. DECOVALEX I - Test Case 1: Coupled stress-flow model

    International Nuclear Information System (INIS)

    Rosengren, L.; Christianson, M.

    1995-12-01

    This report presents the results of the coupled stress-flow model, test case 1 of Decovalex. The model simulates the fourth loading cycle of a coupled stress-flow test and subsequent shearing up to and beyond peak shear resistance. The first loading sequence (A) consists of seven normal loading steps: 0, 5, 15, 25, 15, 5, 0 MPa. The second loading sequence (B) consists of the following eight steps: unstressed state, normal boundary loading of 25 MPa (no shearing), and then shearing of 0.5, 0.8, 2, 4, 2, 0 mm. Two different options regarding the rock joint behaviour were modeled in accordance with the problem definition. In option 1 a linear elastic joint model with Coulomb slip criterion was used. In option 2 a non-linear empirical (i.e. Barton-Bandis) joint model was used. The hydraulic condition during both load sequence A and B was a constant head of 5 m at the inlet point and 0 m at the outlet point. All model runs presented in this report were performed using the two-dimensional distinct element computer code UDEC, version 1.8. 30 refs, 36 figs

  15. Analysing earthquake slip models with the spatial prediction comparison test

    KAUST Repository

    Zhang, L.

    2014-11-10

    Earthquake rupture models inferred from inversions of geophysical and/or geodetic data exhibit remarkable variability due to uncertainties in modelling assumptions, the use of different inversion algorithms, or variations in data selection and data processing. A robust statistical comparison of different rupture models obtained for a single earthquake is needed to quantify the intra-event variability, both for benchmark exercises and for real earthquakes. The same approach may be useful to characterize (dis-)similarities in events that are typically grouped into a common class of events (e.g. moderate-size crustal strike-slip earthquakes or tsunamigenic large subduction earthquakes). For this purpose, we examine the performance of the spatial prediction comparison test (SPCT), a statistical test developed to compare spatial (random) fields by means of a chosen loss function that describes an error relation between a 2-D field (‘model’) and a reference model. We implement and calibrate the SPCT approach for a suite of synthetic 2-D slip distributions, generated as spatial random fields with various characteristics, and then apply the method to results of a benchmark inversion exercise with known solution. We find the SPCT to be sensitive to different spatial correlations lengths, and different heterogeneity levels of the slip distributions. The SPCT approach proves to be a simple and effective tool for ranking the slip models with respect to a reference model.

  16. Un Nouveau Monde du Savoir

    International Development Research Centre (IDRC) Digital Library (Canada)

    Si les effets de la mondialisation sur l'économie, la politique ou encore les ..... Il souligne l'importance cruciale d'un plan stratégique d'internationalisation, ...... Lors du recrutement de nouveaux professeurs ( lorsque cette situation est ...

  17. rive gauche du fleuve Rimac

    International Development Research Centre (IDRC) Digital Library (Canada)

    tégée du fleuve et les terrains vagues d'une zone industrielle. .... Ces deux diagnostics sont d'importants outils qui contri- bueront à une meilleure planification ... conditions et instruments nécessaires pour améliorer la situation financière des ...

  18. Voorwoord Forward | du Plessis | Lexikos

    African Journals Online (AJOL)

    J.CM.D. du Plessis. Abstract. No Abstract. Full Text: EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT · AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms and Conditions ...

  19. Charte du Conseil des Gouverneurs

    International Development Research Centre (IDRC) Digital Library (Canada)

    Office 2004 Test Drive User

    7. favoriser des communications ouvertes et franches entre le personnel, la direction ..... de dresser le procès-verbal des réunions du Conseil et de ses comités et de veiller à ce ... et des résultats qu'il obtient, et non de sa gestion quotidienne.

  20. Bases biologiques du comportement social

    CERN Document Server

    Laborit, H

    1994-01-01

    Pour bien comprendre le comportement humain dans un environnement social,il est necessaire de comprendre comment fonctionne le systÂ?me nerveux central. L'une des principales fonctions du cerveau est de crÂ?er des relations entre leshumains.. .................