22 CFR 3a.4 - Procedure for requesting approval.

Science.gov (United States)

2010-04-01

... is also required by law for the applicant's acceptance of civil employment from a foreign government... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Procedure for requesting approval. 3a.4 Section 3a.4 Foreign Relations DEPARTMENT OF STATE GENERAL ACCEPTANCE OF EMPLOYMENT FROM FOREIGN GOVERNMENTS...

40 CFR 86.163-00 - Spot check correlation procedures for vehicles tested using a simulation of the environmental...

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Spot check correlation procedures for... Complete Heavy-Duty Vehicles; Test Procedures § 86.163-00 Spot check correlation procedures for vehicles... running change approval, each model year for any manufacturer undergoing the spot checking procedures of...

46 CFR 163.002-9 - Approval procedure.

Science.gov (United States)

2010-10-01

... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS... designs. A pilot hoist that does not meet the materials, construction, or performance requirements of this... or in addition to the approval tests required by this subpart, show that the alternative materials...

46 CFR 160.077-6 - Approval procedures.

Science.gov (United States)

2010-10-01

... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS... to the particular design or that by design or construction the PFD cannot fail the test. (c) Alternative Requirements. A PFD that does not meet requirements in this subpart may still be approved if the...

A Review of Clinical Data for Currently Approved Hysteroscopic Sterilization Procedures

Science.gov (United States)

Basinski, Cindy M

2010-01-01

Two hysteroscopic permanent sterilization procedures are approved for use in the United States: Essure® Permanent Birth Control System (Conceptus Incorporated, Mountain View, CA) and Adiana® Permanent Contraception (Hologic, Inc., Bedford, MA). This review compares the clinical trial data for these procedures. A notable difference is the resultant clinical pregnancy risk. The clinical trials for the Essure procedure have reported no pregnancies in 643 relying women in the 9 years since initiation of the studies. The clinical trial for the Adiana procedure has reported 12 pregnancies in 570 relying women in nearly 5 years of collected data. Other clinical outcome parameters concerning Essure and Adiana are examined in this review. PMID:21364861

34 CFR 668.144 - Application for test approval.

Science.gov (United States)

2010-07-01

... quantitative skills; (9) If a test has been revised from the most recent edition approved by the Secretary, an... Education Regulations of the Offices of the Department of Education (Continued) OFFICE OF POSTSECONDARY... inquiries; (3) Each edition and form of the test for which the publisher requests approval; (4) The...

15 CFR 400.32 - Procedure for review of request for approval of manufacturing or processing.

Science.gov (United States)

2010-01-01

... approval of manufacturing or processing. 400.32 Section 400.32 Commerce and Foreign Trade Regulations... REGULATIONS OF THE FOREIGN-TRADE ZONES BOARD Manufacturing and Processing Activity-Reviews § 400.32 Procedure for review of request for approval of manufacturing or processing. (a) Request as part of application...

Decisions in licensing and plan approval procedures, investigated from the viewpoint of legal reservation

International Nuclear Information System (INIS)

Boerger, M.

1987-01-01

Starting from the basic idea that also in the field of environmental law, (constitutional) system immanent problem solution is possible only after basic constitutional questions have been clarified, this study in hand is an attempt towards defining the constitutional approach for an adequate use of the various types of action of the executive in the procedures for approval and licensing of privately owned plant or equipment. The study goes into the problems encountered with the legal reservation with regard to licensing and plan approval decisions. The basic types of action of the executive are subdivided according to intent, i.e. assigned to the supervisory or the planning intents, and are examined for a possible scope of discretion opened up for the administration. The decisive question in this context is the scope of action that may be given to the administration by the legislation, and to what extent such 'freedom' will stand the acceptance test by the courts. (orig./HSCH) [de

Rail Impact Testing. Test Operations Procedure (TOP)

Science.gov (United States)

2008-09-15

impact test. The rail impact test is used to verify structural integrity of the test item and the adequacy of the tie-down system and tie-down...strength of provisions, connection and supporting structural frame, paragraph 5.2.3 ** Superscript...parts, to include outriggers and booms) without advanced approval by SDDCTEA. Torque nuts on wire rope clips to their correct value. Torque cable

40 CFR 610.64 - Track test procedures.

Science.gov (United States)

2010-07-01

... truck or trailer. (4) Fuel economy will be determined by either a gravimetric or volumetric method. (c... dynamometer except that fuel economy will be measured by gravimetric or volumetric methods. ... either a volumetric or gravimetric procedure approved by the Administrator. (5) Vehicle speed and...

Regional planning and plan approval procedures for development and modification of HV grids; Raumordnungs- und Planfeststellungsverfahren fuer den Aus- und Umbau der Hochspannungsnetze

Energy Technology Data Exchange (ETDEWEB)

Hennig, Jan; Luehmann, Tobias [Sozietaet Gleiss Lutz, Berlin (Germany)

2012-07-01

If renewable energy sources are to be integrated, HV grids in Germany must be expanded and upgraded massively. Plans for new ultrahigh voltage lines find a legal basis in the grid expansion acceleration act (NABEG) of 2011 while most of the plans for 110 kV HV lines are still based on the conventional regional planning procedures with public participation followed by a plan approval procedure. With the decentralisation of power supply, these distribution grids are rapidly developing into power collecting grids, which makes high demands in terms of adaptation and upgrading. The contribution presents the legal boundary conditions and practical challenges accompanying the planning of HV lines outside the scope of the NABEG. It outlines the limited options for priorisation of test points in the regional planning and subsequent plan approval procedures and shows how friction between these may be reduced. Buried cables as an alternative to overhead cables are given particular attention as these have come into focus with the energy turnaround legislation of 2011.

77 FR 21451 - Approval and Promulgation of Air Quality Implementation Plans; Colorado; Procedural Rules...

Science.gov (United States)

2012-04-10

... Promulgation of Air Quality Implementation Plans; Colorado; Procedural Rules; Conflicts of Interest AGENCY... potential conflicts of interest. We are also approving the remaining portion of Colorado's January 7, 2008... or more Indian tribes, on the relationship between the Federal Government and Indian tribes, or on...

Development of interim test methods and procedures for determining the performance of small photovoltaic systems

Energy Technology Data Exchange (ETDEWEB)

McNutt, P.; Kroposki, B.; Hansen, R.; Algra, K.; DeBlasio, R. [National Renewable Energy Lab., Golden, CO (United States)

1998-09-01

The National Renewable Energy Laboratory (NREL) is developing tests and procedures that will determine if the configuration of a small photovoltaic (PV) system is suitable for its intended use, and if the system will perform as specified. An overview of these procedures is presented in this paper. Development of standard test procedures will allow designers, manufacturers, system integrators, users, and independent laboratories to assess the performance of PV systems under outdoor prevailing conditions. An NREL Technical Report detailing the procedures is under way, and the IEEE Standards Coordinating Committee 21 (SCC21) has established a project on this subject. The work will be submitted to the IEEE SCC21 and International Electrotechnical Commission Technical Committee 82 (IEC TC82) for consideration as a consensus standard. Certification bodies such as PowerMark and PV Global Approval Program (PVGAP) may adopt the IEC and IEEE documents when testing systems. Developing standardized test methods and procedures at NREL to evaluate the outdoor performance of PV systems will encourage product quality and promote PV standards development. Standardized tests will assure people that PV systems will perform as specified for their intended applications. As confidence in PV systems increases, the successful commercialization of PV will grow internationally.

9 CFR 54.11 - Approval of laboratories to run official scrapie tests and official genotype tests.

Science.gov (United States)

2010-01-01

... request approval to conduct one or more types of scrapie test or genotype test on one or more types of... type of test and for each type of tissue for which they request approval. (c) The Administrator may... the laboratory and shall give the director an opportunity to respond. If there are conflicts as to any...

9 CFR 55.8 - Official CWD tests and approval of laboratories to conduct official CWD tests.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Official CWD tests and approval of laboratories to conduct official CWD tests. 55.8 Section 55.8 Animals and Animal Products ANIMAL AND PLANT... on live or dead animals, and will base the approval or disapproval of a test on the evaluation by...

Test report - caustic addition system operability test procedure

International Nuclear Information System (INIS)

Parazin, R.E.

1995-01-01

This Operability Test Report documents the test results of test procedure WHC-SD-WM-OTP-167 ''Caustic Addition System Operability Test Procedure''. The Objective of the test was to verify the operability of the 241-AN-107 Caustic Addition System. The objective of the test was met

40 CFR 53.65 - Test procedure: Loading test.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 5 2010-07-01 2010-07-01 false Test procedure: Loading test. 53.65... Characteristics of Class II Equivalent Methods for PM2.5 § 53.65 Test procedure: Loading test. (a) Overview. (1) The loading tests are designed to quantify any appreciable changes in a candidate method sampler's...

TMACS Test Procedure TP002: Trending

International Nuclear Information System (INIS)

Scanlan, P.K.

1994-01-01

The TMACS Software Project Test Procedures translate the project's acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes. This Test Procedure tests the TMACS Trending functions

40 CFR 53.66 - Test procedure: Volatility test.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 5 2010-07-01 2010-07-01 false Test procedure: Volatility test. 53.66... Characteristics of Class II Equivalent Methods for PM2.5 § 53.66 Test procedure: Volatility test. (a) Overview. This test is designed to ensure that the candidate method's losses due to volatility when sampling semi...

46 CFR 160.076-13 - Approval procedures for inflatable PFDs.

Science.gov (United States)

2010-10-01

..., CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Inflatable Recreational Personal..., construction specifications, and bill of materials. (2) The information specified in § 159.005-5(a)(2) (i... or construction, it is not possible for the PFD to fail that test. (g) Alternative requirements. A...

Automation of the testing procedure

International Nuclear Information System (INIS)

Haas, H.; Fleischer, M.; Bachner, E.

1979-01-01

For the judgement of technologies applied and the testing of specific components of the HTR primary circuit, complex test procedures and data evaluations are required. Extensive automation of these test procedures is indispensable. (orig.) [de

29 CFR 37.64 - What procedures must the Director follow when CRC has completed a post-approval compliance review?

Science.gov (United States)

2010-07-01

... 29 Labor 1 2010-07-01 2010-07-01 true What procedures must the Director follow when CRC has completed a post-approval compliance review? 37.64 Section 37.64 Labor Office of the Secretary of Labor... (WIA) Compliance Procedures § 37.64 What procedures must the Director follow when CRC has completed a...

Electronic Approval of Invoices (AEF)

CERN Document Server

2004-01-01

With a view to the simplification of administrative procedures, AS and FI Departments have completed the second phase of the new procedure for the electronic approval of invoices via the EDH application. The aim of this new procedure is to rationalise the invoice approval process, notably by eliminating paper copies from the approval circuit. This will simplify the processing of invoices and facilitate their timely settlement, while at the same time maintaining a high level of security. Phase II includes handling the electronic approval process of invoices whose amounts do not correspond exactly to those of the associated orders. In such cases, budgetary approval is required for the entire invoiced amount. Further information can be obtained at : http://ais.cern.ch/projs/AEF/help/F_help.htm Phase II of the procedure will be introduced gradually with effect from April 2004. Finance Department, Accounts Payable Section Tel: 72295 Organisation and Procedures Tel: 75885 Information Technologies Department,...

MITG test procedure and results

International Nuclear Information System (INIS)

Eck, M.E.; Mukunda, M.

1983-01-01

Elements and modules for Radioisotope Thermoelectric Generator have been performance tested since the inception of the RTG program. These test articles seldom resembled flight hardware and often lacked adequate diagnostic instrumentation. Because of this, performance problems were not identified in the early stage of program development. The lack of test data in an unexpected area often hampered the development of a problem solution. A procedure for conducting the MITG Test was developed in an effort to obtain data in a systematic, unambiguous manner. This procedure required the development of extensive data acquisition software and test automation. The development of a facility to implement the test procedure, the facility hardware and software requirements, and the results of the MITG testing are the subject of this paper

Toddler test or procedure preparation

Science.gov (United States)

... a test or procedure: Explain the procedure in language your child understands, using plain words. Avoid abstract terms. Make sure your child understands the exact body part involved in the test, and that the ...

75 FR 47817 - Notice of Availability: Test Tools and Test Procedures Approved for the Office of the National...

Science.gov (United States)

2010-08-09

..., Implementation Specifications, and Certification Criteria for Electronic Health Record Technology'' (HIT... Approved for the Office of the National Coordinator for Health Information Technology (ONC) Temporary Certification Program AGENCY: Office of the National Coordinator for Health Information Technology, Office of...

AZ-101 Mixer Pump Test Qualification Test Procedures (QTP)

International Nuclear Information System (INIS)

THOMAS, W.K.

2000-01-01

Describes the Qualification test procedure for the AZ-101 Mixer Pump Data Acquisition System (DAS). The purpose of this Qualification Test Procedure (QTP) is to confirm that the AZ-101 Mixer Pump System has been properly programmed and hardware configured correctly. This QTP will test the software setpoints for the alarms and also check the wiring configuration from the SIMcart to the HMI. An Acceptance Test Procedure (ATP), similar to this QTP will be performed to test field devices and connections from the field

12 CFR 24.5 - Public welfare investment after-the-fact notice and prior approval procedures.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 1 2010-01-01 2010-01-01 false Public welfare investment after-the-fact notice and prior approval procedures. 24.5 Section 24.5 Banks and Banking COMPTROLLER OF THE CURRENCY... capital and surplus represented by the proposed investment and by the bank's aggregate outstanding public...

78 FR 29780 - Fees for Testing, Evaluation, and Approval of Mining Products

Science.gov (United States)

2013-05-21

... Approval of Mining Products AGENCY: Mine Safety and Health Administration, Labor. ACTION: Notice. SUMMARY..., and approval of mining products; it allows MSHA to collect fees up to $2,499,000 for the testing, evaluation, and approval of certain mining equipment. MSHA is continuing to collect these fees for 2013 as...

TMACS Test Procedure TP007: System administration

International Nuclear Information System (INIS)

Scanlan, P.; Washburn, S.; Seghers, R.

1994-01-01

The TMACS Software Project Test Procedures translate the project's acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes. This Test Procedure tests the TMACS System Administration functions

Fabrication and characterization of MCC approved testing material - ATM-8 glass

International Nuclear Information System (INIS)

Wald, J.W.

1985-10-01

The Materials Characterization Center (MCC) Approved Testing Material ATM-8 is a borosilicate glass that incorporates elements typical of high-level waste (HLW) resulting from the reprocessing of commercial nuclear reactor fuel. Its composition is based upon the simulated HLW glass type 76-68 (Mendel, J.E. et al., 1977, Annual Report of the Characteristics of High-Level Waste Glasses, BNWL-2252, Pacific Northwest Laboratory, Richland, Washington), to which depleted uranium, technetium-99, neptunium-237 and plutonium-239 have been added at moderate to low levels. The glass was requested by the Nevada Nuclear Waste Storage Investigations (NNWSI) Project. It was produced by the MCC at the Pacific Northwest Laboratory (PNL) operated for the Department of Energy (DOE) by Battelle Memorial Institute. ATM-8 glass was produced in April of 1984, and is the second in a series of testing materials for NNWSI. This report discusses its fabrication (starting materials, batch and glass preparation, measurement and testing equipment, other equipment, procedures, identification system and materials availability and storage, and characterization (bulk density) measurements, chemical analysis, microscopic examination, and x-ray diffraction analysis. 4 refs., 2 figs., 10 tabs

TMACS Test Procedure TP009: Acromag Driver

International Nuclear Information System (INIS)

Washburn, S.J.

1994-01-01

The TMACS Software Project Test Procedures translate the project's acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes. This Test Procedure tests the TMACS Acromag Software Driver (Bridge Code)

40 CFR 53.64 - Test procedure: Static fractionator test.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 5 2010-07-01 2010-07-01 false Test procedure: Static fractionator test. 53.64 Section 53.64 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Performance Characteristics of Class II Equivalent Methods for PM2.5 § 53.64 Test procedure: Static...

[Approval of ISO/IEC 17025 and quality control of laboratory testing].

Science.gov (United States)

Yamamoto, Shigeki; Asakura, Hiroshi; Machii, Kenji; Igimi, Shizunobu

2010-01-01

First section of Division of Biomedical Food Research, National Institute of Health Sciences (NIHS) was approved by ISO/IEC 17025 as a laboratory having an appropriate laboratory testing technique. NIHS is the first national laboratory approved by ISO/IEC 17025. NIHS has also been accepted the appropriate technique and facility for the BSL3 level pathogens by ISO/IEC 17025. NIHS is necessary to take an external audit almost every year. This approval is renewed every 4 years.

40 CFR 205.54 - Test procedures.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Test procedures. 205.54 Section 205.54 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) NOISE ABATEMENT PROGRAMS TRANSPORTATION EQUIPMENT NOISE EMISSION CONTROLS Medium and Heavy Trucks § 205.54 Test procedures. The procedures described...

Project W-320, operational test procedure OTP-320-003 test report

International Nuclear Information System (INIS)

Bevins, R.R.

1998-01-01

This report documents and summarizes the results of OTP-320-003 Project W-320 Operational Testing of the WRSS Supernate Transfer System. Project W-320 Operational Test OTP-320-003 was performed to verify components of the Waste Retrieval Sluicing System (WRSS) supernate transfer system functioned as designed following construction completion and turnover to operations. All equipment operation was performed by Tank Farms Operations personnel following the operational test procedure and referenced operating procedures. Supernate Transfer line Flushing System Testing was completed over the course of approximately 4 weeks as tank farm conditions and configuration, equipment availability, and operations resources allowed. All testing was performed with the 702-AZ ventilation system and the 296-P-16 ventilation systems in operation. Test procedure OTP-320-003 required two revisions during testing to incorporate Procedure Changes Authorizations (PCAs) necessary to facilitate testing. Various sections of testing are documented on each procedure revision. The completed test procedure is included as Attachment A. Exception Reports generated during the course of testing are included as Attachment B

19 CFR 115.41 - Certificate of approval for containers approved after manufacture.

Science.gov (United States)

2010-04-01

... after manufacture. 115.41 Section 115.41 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT... PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers After Manufacture § 115.41 Certificate of approval for containers approved after manufacture. The Certifying Authority shall...

7 CFR 1710.406 - Loan approval.

Science.gov (United States)

2010-01-01

... 7 Agriculture 11 2010-01-01 2010-01-01 false Loan approval. 1710.406 Section 1710.406 Agriculture... GENERAL AND PRE-LOAN POLICIES AND PROCEDURES COMMON TO ELECTRIC LOANS AND GUARANTEES Application Requirements and Procedures for Loans § 1710.406 Loan approval. (a) A loan is approved when the Administrator...

Parametric Sensitivity Tests- European PEM Fuel Cell Stack Test Procedures

DEFF Research Database (Denmark)

Araya, Samuel Simon; Andreasen, Søren Juhl; Kær, Søren Knudsen

2014-01-01

performed based on test procedures proposed by a European project, Stack-Test. The sensitivity of a Nafion-based low temperature PEMFC stack’s performance to parametric changes was the main objective of the tests. Four crucial parameters for fuel cell operation were chosen; relative humidity, temperature......As fuel cells are increasingly commercialized for various applications, harmonized and industry-relevant test procedures are necessary to benchmark tests and to ensure comparability of stack performance results from different parties. This paper reports the results of parametric sensitivity tests......, pressure, and stoichiometry at varying current density. Furthermore, procedures for polarization curve recording were also tested both in ascending and descending current directions....

Electronic Approval of Invoices (AEF)

CERN Multimedia

2003-01-01

With a view to the simplification of administrative procedures, AS and FI Divisions have drawn up a new procedure for the electronic approval of invoices via the EDH application. The aim of this new procedure is to rationalise the invoice approval process, notably by eliminating paper copies from the approval circuit. This will simplify the processing of invoices and facilitate their timely settlement, while at the same time maintaining a high level of security. This new procedure, in its current phase, will be gradually implemented from 1 November 2003 onwards. For clarification and further information, please see: http://ais.cern.ch/projs/AEF/help/help.htm . Finance Division, Accounts Payable Tel.: 7.22.95

Medicaid program; Medicaid Management Information Systems; conditions of approval and reapproval and procedures for reduction of federal financial participation--Health Care Financing Administration. Proposed rule.

Science.gov (United States)

1983-03-03

This proposal adds to regulations new conditions and procedures for initial approval and for reapproval of Medicaid Management Information Systems (MMIS) to update the regulations to reflect additional requirements added by section 901 of the Mental Health Systems Act of 1980 (Pub. L. 96-398). The proposal specifies procedures for reducing the level of Federal financial participation in a State's administrative expenditures when a State fails to meet the conditions for initial operation, initial approval or reapproval of an MMIS. It also proposes procedures with respect to waivers of the conditions of approval and reapproval and to appeals of adverse decisions. These provisions are intended to improve States' MMIS, and to ensure efficient system operations, and to detect cases of fraud, waste, and abuse effectively.

Medicaid program; Medicaid Management Information Systems; conditions of approval and reapproval and procedures for reduction of Federal financial participation--HCFA. Final rule.

Science.gov (United States)

1985-07-30

This final rule provides the additional requirements to the conditions and procedures for initial approval and reapproval of Medicaid Management Information Systems (MMIS) that were added by section 1903(r) of the Social Security Act (as amended by section 901 of the Mental Health Systems Act of 1980, Pub. L. 96-398). These provisions are intended to improve States' MMIS, ensure efficient system operations, and make the procedures for detection of fraud, waste, and abuse more effective. In addition, this final rule specifies the procedures we follow in reducing the level of Federal financial participation in State administrative expenditures if a State fails to meet the conditions for initial operation, initial approval, or reapproval of an MMIS.

Test and approval center for fuel cell and hydrogen technologies: Phase I. Initiation. Final report; Test- og godkendelsescenter for braendselscelle- og brintteknologier. Fase 1. Opstart. Slutrapport

Energy Technology Data Exchange (ETDEWEB)

Hagen, A. [Technical Univ. of Denmark. DTU Energy Conversion, DTU Risoe Campus, Roskilde (Denmark)

2012-09-15

The aim of the present project was to initialize a Test and Approval Center for Fuel Cell and Hydrogen Technologies at the sites of the project partners Risoe DTU (Fuel Cells and Solid State Chemistry Division), and DGC (work package 1). The project furthermore included start-up of first activities with focus on the development of accelerated life-time tests of fuel cell systems, preparations for standardization of these methods, and advising in relation to certification and approval of fuel cell systems (work package 2). The main achievements of the project were: Work package 1: 1) A large national and international network was established comprising of important commercial players, research institutions, and other test centers; 2) The test center is known in large part of the international Fuel Cell and Hydrogen community due to substantial efforts in 'marketing'; 3) New national and international projects have been successfully applied for, with significant roles of the test center, which secure the further establishment and development of the center. Work package 2: 1) Testing equipment was installed and commissioned at DTU (Risoe Campus); 2) A comprehensive survey among international players regarding activities on accelerated SOFC testing was carried out; 3) A test procedure for 'compressed' testing of SOFC in relation to {mu} CHP application was developed and used for one-cell stack and 50-cell-stack testing; 4) Guidelines for Danish authority handling were formulated. (Author)

48 CFR 52.209-3 - First Article Approval-Contractor Testing.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false First Article Approval... Clauses 52.209-3 First Article Approval—Contractor Testing. As prescribed in 9.308-1 (a) and (b), insert the following clause: First Article Approval—Contractor Testing (SEP 1989) [Contracting Officer shall...

48 CFR 52.209-4 - First Article Approval-Government Testing.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false First Article Approval... Clauses 52.209-4 First Article Approval—Government Testing. As prescribed in 9.308-2 (a) and (b), insert the following clause: First Article Approval—Government Testing (SEP 1989) [Contracting Officer shall...

10 CFR 474.4 - Test procedures.

Science.gov (United States)

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Test procedures. 474.4 Section 474.4 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ELECTRIC AND HYBRID VEHICLE RESEARCH, DEVELOPMENT, AND DEMONSTRATION PROGRAM; PETROLEUM-EQUIVALENT FUEL ECONOMY CALCULATION § 474.4 Test procedures. (a) The electric vehicle energy...

40 CFR 89.406 - Pre-test procedures.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Pre-test procedures. 89.406 Section 89.406 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED... Procedures § 89.406 Pre-test procedures. (a) Allow a minimum of 30 minutes warmup in the standby or operating...

Dispersant testing : a study on analytical test procedures

International Nuclear Information System (INIS)

Fingas, M.F.; Fieldhouse, B.; Wang, Z.; Environment Canada, Ottawa, ON

2004-01-01

Crude oil is a complex mixture of hydrocarbons, ranging from small, volatile compounds to very large, non-volatile compounds. Analysis of the dispersed oil is crucial. This paper described Environment Canada's ongoing studies on various traits of dispersants. In particular, it describes small studies related to dispersant effectiveness and methods to improve analytical procedures. The study also re-evaluated the analytical procedure for the Swirling Flask Test, which is now part of the ASTM standard procedure. There are new and improved methods for analyzing oil-in-water using gas chromatography (GC). The methods could be further enhanced by integrating the entire chromatogram rather than just peaks. This would result in a decrease in maximum variation from 5 per cent to about 2 per cent. For oil-dispersant studies, the surfactant-dispersed oil hydrocarbons consist of two parts: GC-resolved hydrocarbons and GC-unresolved hydrocarbons. This study also tested a second feature of the Swirling Flask Test in which the side spout was tested and compared with a new vessel with a septum port instead of a side spout. This decreased the variability as well as the energy and mixing in the vessel. Rather than being a variation of the Swirling Flask Test, it was suggested that a spoutless vessel might be considered as a completely separate test. 7 refs., 2 tabs., 4 figs

TMACS test procedure TP003: Graphics. Revision 5

International Nuclear Information System (INIS)

Scanlan, P.K.

1994-01-01

The TMACS Software Project Test Procedures translate the project's acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes. This Test Procedure addresses the graphics requirements of the TMACS. The features to be tested are the data display graphics and the graphic elements that provide for operator control and selection of displays

TMACS test procedure TP003: Graphics. Revision 6

International Nuclear Information System (INIS)

Scanlan, P.K.; Washburn, S.

1994-01-01

The TMACS Software Project Test Procedures translate the project's acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes. This Test Procedure addresses the graphics requirements of the TMACS. The features to be tested are the data display graphics and the graphic elements that provide for operator control and selection of displays

On the scope of the Federal Government to issue orders in plan approval procedures under para. 9b of the Atomic Energy Act as provided by article 85 section 3 of the Basic Law

International Nuclear Information System (INIS)

Ossenbuehl, F.

1991-01-01

Under Paragraph 9b of the Atomic Energy Act the Lower Saxonian Minister of the Environment has the competence for the plan approval procedure concerning the final disposal site Konrad. The plan approval procedure under atomic energy law is a unitary administrative procedure which makes further administrative procedures and administrative decisions superfluous on the strength of its unitary character and without impingement on constitutional law. In conducting the plan approval procedure the Lower Saxonican Minister of the Environment is acting within the framework of Laender administration on behalf of the Federation. To this extent he is subject to the orders of the Federal Minister of the Enviroment under Article 85 Section 3 of The Basic Law with respect to the formation of the procedure and procedural decisions as well as decisions on the merits pending. The concentrating effect of the plan approval procedure under atomic energy law also extends to permits under water law. (orig./HSCH) [de

Judicial problems in connection with preliminary decision and construction design approval in nuclear licensing procedures

International Nuclear Information System (INIS)

Schmieder, K.

1977-01-01

Standardization in nuclear engineering makes two demands on a legal instrument which is to make this standardization possible and which is to promote standardization in the nuclear licensing practice: On the basis of just one licence for a constructional part or a component, its applicability in any number of subsequent facility licensing procedures has to be warranted, and by virtue of its binding effect, standardization has to create a sufficiently big confidence protection with manufacturers, constructioneers and operators to offer sufficiently effective incentives for standardization. The nuclear preliminary decision pursuant to section 7 a of the Atomic Energy Act in the form of the component preliminary decision appears to be unsuitable as a legal instrument for standardization, as the preliminary decision refers exclusively to the construction of a concrete facility. For standardization in reactor engineering, the construction design approval appears to be basically the proper legal instrument on account of its legal structure as well as its economic effect. Its binding effect encouters a limitation with regard to third parties in so far that this limitation could question again the binding effect in a subsequent site-dependent nuclear licence procedure. The legal structure of the extent of the binding effect, which is decisive for the suitability of the construction design approval, lies with the legislator. The following questions have to be regulated: Ought the applicant to have a legal claim on the granting of a construction design approval, or ought it to be at the discretion of the authorities, and secondly, the extent of the binding effect in terms of time on the basis of the fixation of a time limit, or on the basis of the possibility of subsequent conditions to be imposed, or the revocation. (orig./HP) [de

Analysis and optimization of blood-testing procedures.

NARCIS (Netherlands)

Bar-Lev, S.K.; Boxma, O.J.; Perry, D.; Vastazos, L.P.

2017-01-01

This paper is devoted to the performance analysis and optimization of blood testing procedures. We present a queueing model of two queues in series, representing the two stages of a blood-testing procedure. Service (testing) in stage 1 is performed in batches, whereas it is done individually in

DOT-7A packaging test procedure

International Nuclear Information System (INIS)

Kelly, D.L.

1995-01-01

This test procedure documents the steps involved with performance testing of Department of Transportation Specification 7A (DOT-7A) Type A packages. It includes description of the performance tests, the personnel involved, appropriate safety considerations, and the procedures to be followed while performing the tests. Westinghouse Hanford Company (WHC) is conducting the evaluation and testing discussed herein for the Department of Energy-Headquarters, Division of Quality Verification and Transportation Safety (EH-321). Please note that this report is not in WHC format. This report is being submitted through the Engineering Documentation System so that it may be used for reference and information purposes

TMACS Test Procedure TP008: SACS Interface. Revision 5

International Nuclear Information System (INIS)

Washburn, S.J.

1994-01-01

The TMACS Software Project Test Procedures translate the project's acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes. This Test Procedure tests the TMACS SACS Interface functions

TMACS test procedure TP010: Integration summary. Revision 6

International Nuclear Information System (INIS)

Spurling, D.G.

1994-01-01

The TMACS Software Project Test Procedures translate the project's acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes. This Test Procedure verifies that Test Procedures 1, 2, 3, 5 and 9 (WHC-SD-WM-TRP-105, 106, 107, 109 and 113) of TMACS Software Release 4.1 have been successfully completed

W-087 Acceptance test procedure. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Joshi, A.W.

1997-06-10

This Acceptance Test Procedure/Operational Test Procedure (ATP/OTP) has been prepared to demonstrate that the Electrical/Instrumentation and Mechanical systems function as required by project criteria and to verify proper operation of the integrated system including the interlocks.

W-087 Acceptance test procedure. Revision 1

International Nuclear Information System (INIS)

Joshi, A.W.

1997-01-01

This Acceptance Test Procedure/Operational Test Procedure (ATP/OTP) has been prepared to demonstrate that the Electrical/Instrumentation and Mechanical systems function as required by project criteria and to verify proper operation of the integrated system including the interlocks

Report on COTECH test procedure and characterization techniques

DEFF Research Database (Denmark)

Islam, Mohammad Aminul

that need to be attained for successful characterization of the planned demonstrators and it deals with the material characterization and prototype testing for the COTECH demonstrators. The summary of this report includes:  General description of COTECH industrial demonstrators  COTECH materials...... and material characterization techniques  Characterization techniques of the COTECH demonstrators  Functionality and lifecycle testing of the COTECH demonstrators Besides the general introduction and conclusion each section of the report is dedicated to the characterization techniques and test procedure.......Characterization techniques and test procedure requirements for innovative self-ligating dental brackets (EO) Section 5.Characterization techniques and test procedure requirements for smart diagnostic chips comprising a microfluidic channel system (GBO) Section 6.Characterization techniques and test procedure...

Endurance test for IR rig for RI production assembly (test procedure)

International Nuclear Information System (INIS)

Chung, Heung June; Ryu, Jeong Soo

2000-08-01

This test procedure details the test loop, test method, and test procedure for pressure drop, vibration and endurance test of IR Rig for RI production. From the pressure drop test, the hydraulic design requirements of the capsule are verified. HANARO limit condition is checked and the compatibility with HANARO core is verified. From flow induced vibration test vibration frequency and displacement are investigated. The wear of IR Rig is investigated through endurance test, and these data are used to evaluate the expected wear at maximum resident time of the IR Rig for RI production

EU-approved rapid tests might underestimate bovine spongiform encephalopathy infection in goats

NARCIS (Netherlands)

Meloni, Daniela; Bozzetta, Elena; Langeveld, Jan P.M.; Groschup, Martin H.; Goldmann, Wilfred; Andrèoletti, Olivier; Lantier, Isabelle; Keulen, Van Lucien; Bossers, Alex; Pitardi, Danilo; Nonno, Romolo; Sklaviadis, Theodoros; Ingravalle, Francesco; Peletto, Simone; Colussi, Silvia; Acutis, Pier Luigi

2017-01-01

We report the diagnostic sensitivity of 3 EU-approved rapid tests (ELISAs; 1 from IDEXX and 2 from Bio-Rad) for the detection of transmissible spongiform encephalopathy diseases in goats. Ninety-eight goat brainstem samples were tested. All the rapid tests had 100% specificity and ≥80% sensitivity,

Acceptance test procedure for Project W-280

International Nuclear Information System (INIS)

Stites, C.G.

1994-01-01

This Document is the Acceptance Test Procedure for 200 Area C and SY Tank Farm Lighting Upgrade. This Acceptance Test Procedure has been prepared to demonstrate that the Tank Farm Lighting Systems function correctly as required by project criteria and as intended by design

Acceptance test procedure, 241-SY-101 Flexible Receiver System, Phase III testing

International Nuclear Information System (INIS)

Ritter, G.A.

1994-01-01

This Acceptance Test Procedure is for the 241-SY-101 Flexible Receiver System, Phase III Testing. This procedure will test the sealing integrity of the Flexible Receiver System to ensure that release of waste and aerosols will be minimized during the removal of the test mixer pump from tank SY-101

Factory Acceptance Test Procedure Westinghouse 100 ton Hydraulic Trailer

International Nuclear Information System (INIS)

Aftanas, B.L.

1994-01-01

This Factory Acceptance Test Procedure (FAT) is for the Westinghouse 100 Ton Hydraulic Trailer. The trailer will be used for the removal of the 101-SY pump. This procedure includes: safety check and safety procedures; pre-operation check out; startup; leveling trailer; functional/proofload test; proofload testing; and rolling load test

40 CFR 53.23 - Test procedures.

Science.gov (United States)

2010-07-01

... deviation about the mean and is expressed in concentration units. (2) Test procedure. (i) Allow sufficient... definition. Positive or negative response caused by a substance other than the one being measured. (2) Test...) Before testing for each interferent, allow the test analyzer to sample through the scrubber a test...

TMACS test procedure TP009: Acromag driver. Revision 5

International Nuclear Information System (INIS)

Bass, R.B.; Washburn, S.J.

1994-01-01

The TMACS Software Project Test Procedures translate the project's acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes. This Test Procedure addresses the testing of the functionality of the TMACS Acromag driver software in conjunction with a new bridge for the Panalarm Annunciator system

A new approach to household appliance energy test procedures

Energy Technology Data Exchange (ETDEWEB)

Ernebrant, S.; Wihlborg, M.

1999-03-01

Energy test procedures provides the industry with a method to measure its products energy consumption. The energy test procedures are the technical foundation to every energy standard and labelling system. Depending on which country the product is going to be sold in, the manufacturers must follow different standards. This report concentrates on appliance test procedures, with the main focus on refrigerators. Recently, a new technology -microcontrollers- is undermining the credibility of the test procedures. New features, saving energy in real-life, are not picked up by the test procedures. It is estimated that as much as 30% of energy could be saved with this technology. Microcontrollers have also led to the possibility to circumvent tests. A new model is presented in the report, which handles these energy savings and make it harder cheating on tests. The model divides the test procedure in two parts; hardware tests and software tests, and uses a Matlab/Simulink computer model to calculate the energy consumption. Examples of hardware- and software test methods for refrigerators are described. A refrigerator is used as an example to present the model. The possibility to harmonize the energy standards to one global standard, which could mean substantial savings and make international trade more efficient, is also discussed 24 refs, 30 figs. Examination paper

Price, performance, and the FDA approval process: the example of home HIV testing.

Science.gov (United States)

Paltiel, A David; Pollack, Harold A

2010-01-01

The Food and Drug Administration (FDA) is considering approval of an over-the-counter, rapid HIV test for home use. To support its decision, the FDA seeks evidence of the test's performance. It has asked the manufacturer to conduct field studies of the test's sensitivity and specificity when employed by untrained users. In this article, the authors argue that additional information should be sought to evaluate the prevalence of undetected HIV in the end-user The analytic framework produces the elementary but counterintuitive finding that the performance of the home HIV test- measured in terms of its ability to correctly detect the presence and absence of HIV infection among the people who purchase it-depends critically on the manufacturer's retail price. This finding has profound implications for the FDA's approval process.

Test and Approval Center for Fuel Cell and Hydrogen Technologies: Phase I. Initiation

DEFF Research Database (Denmark)

already spent on these technologies also lead to commercial success. The project ‘Test and Approval Center for Fuel Cell and Hydrogen Technologies: Phase I. Initiation’ was aiming at starting with the Establishment of such a center. The following report documents the achievements within the project...... of the fluctuating wind energy. As the fuel cell and hydrogen technologies come closer to commercialization, development of testing methodology, qualified testing and demonstration become increasingly important. Danish industrial players have expressed a strong need for support in the process to push fuel cell...... and hydrogen technologies from the research and development stage into the commercial domain. A Center to support industry with test, development, analysis, approval, certification, consultation, and training in the areas of fuel cell and hydrogen technologies was needed. Denmark has demonstrated leading...

27 CFR 5.55 - Certificates of label approval.

Science.gov (United States)

2010-04-01

..., DEPARTMENT OF THE TREASURY LIQUORS LABELING AND ADVERTISING OF DISTILLED SPIRITS Requirements for Approval of... certificates of label approval and certificates of exemption from label approval, as well as appeal procedures...

Competent authority approval of package designs in the United Kingdom

International Nuclear Information System (INIS)

Morgan-Warren, E.J.

1999-01-01

Type B packages and all packages containing fissile material, as well as special form radioactive materials, special arrangements and certain shipments, are required to be approved by the competent authority. In the United Kingdom competent authority approval is carried out on behalf of the Secretary of State by the Radioactive Materials Transport Division (RMTD) of the Department of the Environment, Transport and the Regions (DETR). Competent authority approval of a package design is given only after a detailed assessment of the design by the specialist staff of RMTD. There are three facets to the assessment procedure, namely engineering, criticality and radiation protection, and quality assurance. The engineering assessor ensures that the designer has demonstrated the integrity of the containment and shielding systems under the regulatory conditions. The criticality assessor examines criticality safety and radiation protection measures, and together with the engineering assessor, decides whether this is maintained under regulatory conditions. The quality assurance assessor verifies that the applicant has established the necessary controls to ensure that the design requirements are met. The applicant is responsible for making the case for approval, but the assessment is facilitated if the competent authority is involved with the designer at an early stage in development and during the construction of any test prototype. When a regulatory test programme is required, it is designed and carried out by the applicant, but agreed and witnessed by representatives of RMTD. Following the test programme, the applicant submits a formal application, supported by a design safety report (DSR). The DSR provides a full analysis of the design and the test results, including the behaviour of the package under normal and accident conditions of transport, the manufacturing and maintenance procedures, quality assurance and the emergency provisions for the operation of the package

TMACS test procedure TP001: Alarm management. Revision 6

International Nuclear Information System (INIS)

Scanlan, P.K.

1994-01-01

The TMACS Software Project Test Procedures translate the project's acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes. This Test Procedure addresses the Alarm Management requirements of the TMACS. The features to be tested are: real-time alarming on high and low level and discrete alarms, equipment alarms, dead-band filtering, alarm display color coding, alarm acknowledgement, and alarm logging

Cloud-based Electronic Test Procedures, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Test procedures are at the heart of any experimental process, especially those involving novel and complex hardware. Whether these procedures are for system...

Surface moisture measurement system hardware acceptance test procedure

International Nuclear Information System (INIS)

Ritter, G.A.

1996-01-01

The purpose of this acceptance test procedure is to verify that the mechanical and electrical features of the Surface Moisture Measurement System are operating as designed and that the unit is ready for field service. This procedure will be used in conjunction with a software acceptance test procedure, which addresses testing of software and electrical features not addressed in this document. Hardware testing will be performed at the 306E Facility in the 300 Area and the Fuels and Materials Examination Facility in the 400 Area. These systems were developed primarily in support of Tank Waste Remediation System (TWRS) Safety Programs for moisture measurement in organic and ferrocyanide watch list tanks

Portal monitor evaluation and test procedure

International Nuclear Information System (INIS)

Johnson, L.O.; Gupta, V.P.; Stevenson, R.L.; Rich, B.L.

1983-10-01

The purpose was to develop techniques and procedures to allow users to measure performance and sensitivity of portal monitors. Additionally, a methodology was developed to assist users in optimizing monitor performance. The two monitors tested utilized thin-window gas-flow proportional counters sensitive to beta and gamma radiation. Various tests were performed: a) background count rate and the statistical variability, b) detector efficiency at different distances, c) moving source sensitivity for various size sources and speeds, and d) false alarm rates at different background levels. A model was developed for the moving source measurements to compare the experimental data with measured results, and to test whether it is possible to adequately model the behavior of a portal monitor's response to a moving source. The model results were compared with the actual test results. A procedure for testing portal monitors is also given. 1 reference, 9 figures, 8 tables

Caustic addition system operability test procedure

International Nuclear Information System (INIS)

Parazin, R.E.

1994-11-01

This test procedure provides instructions for performing operational testing of the major components of the 241-AN-107 Caustic Addition System by WHC and Kaiser personnel at the Rotating Equipment Shop run-in pit (Bldg. 272E)

Caustic addition system operability test procedure

Energy Technology Data Exchange (ETDEWEB)

Parazin, R.E.

1994-11-01

This test procedure provides instructions for performing operational testing of the major components of the 241-AN-107 Caustic Addition System by WHC and Kaiser personnel at the Rotating Equipment Shop run-in pit (Bldg. 272E).

Test equality between two binary screening tests with a confirmatory procedure restricted on screen positives.

Science.gov (United States)

Lui, Kung-Jong; Chang, Kuang-Chao

2015-01-01

In studies of screening accuracy, we may commonly encounter the data in which a confirmatory procedure is administered to only those subjects with screen positives for ethical concerns. We focus our discussion on simultaneously testing equality of sensitivity and specificity between two binary screening tests when only subjects with screen positives receive the confirmatory procedure. We develop four asymptotic test procedures and one exact test procedure. We derive sample size calculation formula for a desired power of detecting a difference at a given nominal [Formula: see text]-level. We employ Monte Carlo simulation to evaluate the performance of these test procedures and the accuracy of the sample size calculation formula developed here in a variety of situations. Finally, we use the data obtained from a study of the prostate-specific-antigen test and digital rectal examination test on 949 Black men to illustrate the practical use of these test procedures and the sample size calculation formula.

TMACS Test Procedure TP010: Integration summary. Revision 5

International Nuclear Information System (INIS)

Spurling, D.G.

1994-01-01

The TMACS Soft Project Test Procedures translate the project's acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes

30 CFR 14.22 - Test for flame resistance of conveyor belts.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Test for flame resistance of conveyor belts. 14..., EVALUATION, AND APPROVAL OF MINING PRODUCTS REQUIREMENTS FOR THE APPROVAL OF FLAME-RESISTANT CONVEYOR BELTS Technical Requirements § 14.22 Test for flame resistance of conveyor belts. (a) Test procedures. The test...

46 CFR 159.005-11 - Approval inspection or test report: Contents.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Approval inspection or test report: Contents. 159.005-11 Section 159.005-11 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT... representation is also punishable as a crime under 18 U.S.C. 1001. ...

19 CFR 115.55 - Termination of approval.

Science.gov (United States)

2010-04-01

... vehicle by a major repair or alteration of any of the essential features required in § 115.51. Repairs by... TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Individual Road Vehicles § 115.55 Termination of approval. Approval of a road...

Adolescent test or procedure preparation

Science.gov (United States)

... someone else) during the procedure Playing hand-held video games Using guided imagery Trying other distractions, such as ... effects the test may cause. Older teens may benefit from videos that show adolescents of the same age explaining ...

40 CFR 63.309 - Performance tests and procedures.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Performance tests and procedures. 63.309 Section 63.309 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... Standards for Coke Oven Batteries § 63.309 Performance tests and procedures. (a) Except as otherwise...

40 CFR 76.15 - Test methods and procedures.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Test methods and procedures. 76.15 Section 76.15 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.15 Test methods and procedures. (a) The...

Antimicrobial Testing Methods & Procedures Developed by EPA's Microbiology Laboratory

Science.gov (United States)

We develop antimicrobial testing methods and standard operating procedures to measure the effectiveness of hard surface disinfectants against a variety of microorganisms. Find methods and procedures for antimicrobial testing.

16 CFR 1510.4 - Test procedure.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Test procedure. 1510.4 Section 1510.4 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL HAZARDOUS SUBSTANCES ACT REGULATIONS... plane surface. Under its own weight and in a non-compressed state apply any portion of the test sample...

Testing of tubular goods - a critical review of past and actual testing procedures

Energy Technology Data Exchange (ETDEWEB)

Teodoriu, C. [Texas A and M Univ., Houston, TX (United States); Holzmann, J.; Klaws, M. [TU Clausthal (Germany). Inst. fuer Erdoel- und Erdgastechnik

2007-09-13

Testing of oil country tubular goods (OCTG) is based on standards and offers the user a comparison platform between products of different manufacturers. But, do the standard based testing procedures assume the real loads on OCTG? More likely, the existing standards or recommendations on tubular testing have been evolving together with the new demands on OCTG loading. Since nowadays the oil and gas industry is looking to develop extreme reservoir types (deep water, HP/HT), there is a need of a better understanding and continuous improvement of testing procedures. The following poster proposes an analysis of existing procedures to test tubular goods and then will focus on the future demands on OCTG testing. New loads, as casing fatigue, will be discussed and analyzed based on the authors experience gained during more than 8 years of testing tubular goods at the Clausthal University of Technology, Institute of Petroleum Engineering. (orig.)

Inspection system performance test procedure

International Nuclear Information System (INIS)

Jensen, C.E.

1995-01-01

This procedure establishes requirements to administer a performance demonstration test. The test is to demonstrate that the double-shell tank inspection system (DSTIS) supplied by the contractor performs in accordance with the WHC-S-4108, Double-Shell Tank Ultrasonic Inspection Performance Specification, Rev. 2-A, January, 1995. The inspection system is intended to provide ultrasonic (UT) and visual data to determine integrity of the Westinghouse Hanford Company (WHC) site underground waste tanks. The robotic inspection system consists of the following major sub-systems (modules) and components: Mobile control center; Deployment module; Cable management assembly; Robot mechanism; Ultrasonic testing system; Visual testing system; Pneumatic system; Electrical system; and Control system

Biomonitoring test procedures and biological criteria

Energy Technology Data Exchange (ETDEWEB)

Kszos, L.A. [Oak Ridge National Lab., TN (United States); Lipschultz, M.J. [City of Las Vegas, NV (United States); Foster, W.E. [Saint Mary`s Coll., Winona, MN (United States)

1997-10-01

The Water Environment Federation recently issued a special publication, Biomonitoring in the Water Environment. In this paper, the authors highlight the contents of the chapter 3, Biomonitoring Test Procedures, identify current trends in test procedures and introduce the concept of biological criteria (biocriteria). The book chapter (and this paper) focuses on freshwater and marine chronic and acute toxicity tests used in the National Pollutant Discharge Elimination System (NPDES) permits program to identify effluents and receiving waters containing toxic materials in acutely or chronically toxic concentrations. The two major categories of toxicity tests include acute tests and chronic tests. The USEPA chronic tests required in NPDEs permits have been shortened to 7 days by focusing on the most sensitive life-cycle stages; these tests are often referred to as short-term chronic tests. The type of test(s) required depend on NPDES permit requirements, objectives of the test, available resources, requirements of the test organisms, and effluent characteristics such as variability in flow or toxicity. The permit writer will determine the requirements for toxicity test(s) by considering such factors as dilution, effluent variability, and exposure variability. Whether the required test is acute or chronic, the objective of the test is to estimate the safe or no effect concentration which is defined as the concentration which will permit normal propagation of fish and other aquatic life in the receiving waters. In this paper, the authors review the types of toxicity tests, the commonly used test organisms, and the uses of toxicity test data. In addition, they briefly describe research on new methods and the use of biological criteria.

Cloud-Based Electronic Test Procedures, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — Procedures are critical to experimental tests as they describe the specific steps necessary to efficiently and safely carry out a test in a repeatable fashion. The...

241-AZ-101 Mixer Pump Demonstration Test Gamma Cart Acceptance Test Procedure and Quality Test Plan (ATP and QTP)

International Nuclear Information System (INIS)

WHITE, D.A.

2000-01-01

Shop test of the sludge mobilization cart system to be used in the AZ-101 Mixer Pump Demonstration Test Tests hardware and software. This procedure involves testing the Instrumentation involved with the Gamma Cart System, local and remote, including depth indicators, speed controls, interface to data acquisition software and the raising and lowering functions. This Procedure will be performed twice, once for each Gamma Cart System. This procedure does not test the accuracy of the data acquisition software

241-AZ-101 Mixer Pump Demonstration Test Gamma Cart Acceptance Test Procedure and Quality Test Plan (ATP and QTP)

International Nuclear Information System (INIS)

WHITE, D.A.

2000-01-01

Shop Test of the Gamma Cart System to be used in the AZ-101 Mixer Pump Demonstration Test. Tests hardware and software. This procedure involves testing the Instrumentation involved with the Gamma Cart System, local and remote, including: depth indicators, speed controls, interface to data acquisition software and the raising and lowering functions. This Procedure will be performed twice, once for each Gamma Cart System. This procedure does not test the accuracy of the data acquisition software

MITS Data Acquisition Subsystem Acceptance Test procedure

International Nuclear Information System (INIS)

Allison, R.

1980-01-01

This is an acceptance procedure for the Data Acquisition Subsystem of the Machine Interface Test System (MITS). Prerequisites, requirements, and detailed step-by-step instruction are presented for inspecting and performance testing the subsystem

33 CFR 115.70 - Advance approval of bridges.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Advance approval of bridges. 115... BRIDGES BRIDGE LOCATIONS AND CLEARANCES; ADMINISTRATIVE PROCEDURES § 115.70 Advance approval of bridges. (a) The General Bridge Act of 1946 requires the approval of the location and plans of bridges prior...

An approved personal dosimetry service based on an electronic dosimeter

International Nuclear Information System (INIS)

Marshall, T.O.; Bartlett, D.T.; Burgess, P.H.; Campbell, J.I.; Hill, C.E.; Pook, E.A.; Sandford, D.J.

1991-01-01

At the Second Conference on Radiation Protection and Dosimetry a paper was presented which, in part, announced the development of an electronic dosimeter to be undertaken in the UK by the National Radiological Protection Board (NRPB) and Siemens Plessey Controls Ltd. This dosimeter was to be of a standard suitable for use as the basis of an approved personal dosimetry service for photon and beta radiations. The project has progressed extremely well and dosimeters and readers are about to become commercially available. The system and the specification of the dosimeter are presented. The NRPB is in the process of applying for approval by the Health and Safety Executive (HSE) to operate as personal monitoring service based on this dosimeter. As part of the approval procedure the dosimeter is being type tested and is also undergoing an HSE performance test and wearer trials. The tests and the wearer trials are described and a summary of the results to date presented. The way in which the service will be organized and operated is described and a comparison is made between the running of the service and others based on passive dosimeters at NRPB

Small Optics Laser Damage Test Procedure

Energy Technology Data Exchange (ETDEWEB)

Wolfe, Justin [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-10-19

This specification defines the requirements and procedure for laser damage testing of coatings and bare surfaces designated for small optics in the National Ignition Facility (NIF) at Lawrence Livermore National Laboratory (LLNL).

Specifications for Testing Procedures at Svåheia

DEFF Research Database (Denmark)

Margheritini, Lucia; Kofoed, Jens Peter

This report is realized in order to define testing procedures of the SSG pilot in Svåheia location. This will be done by listing all the relevant parameters related to the structure performance.......This report is realized in order to define testing procedures of the SSG pilot in Svåheia location. This will be done by listing all the relevant parameters related to the structure performance....

27 CFR 4.50 - Certificates of label approval.

Science.gov (United States)

2010-04-01

..., DEPARTMENT OF THE TREASURY LIQUORS LABELING AND ADVERTISING OF WINE Requirements for Approval of Labels of... of exemption from label approval, as well as appeal procedures, see part 13 of this chapter. [T.D...

Diesel generator trailer acceptance test procedure

International Nuclear Information System (INIS)

Kostelnik, A.J.

1994-01-01

This Acceptance Test Procedure (ATP) will document compliance with the requirements of WHC-S-0252 Rev. 1 and ECNs 609271, and 609272. The equipment being tested is a 150KW Diesel Generator mounted on a trailer with switchgear. The unit was purchased as a Design and Fabrication procurement activity. The ATP was written by the Seller and will be performed by the Seller with representatives of the Westinghouse Hanford Company witnessing the test at the Seller's location

78 FR 75961 - Energy Conservation Program: Test Procedures for Electric Motors

Science.gov (United States)

2013-12-13

... Conservation Program: Test Procedures for Electric Motors; Final Rule #0;#0;Federal Register / Vol. 78 , No... Procedures for Electric Motors AGENCY: Office of Energy Efficiency and Renewable Energy, Department of Energy... procedures for electric motors to allow currently unregulated motors to be tested by clarifying the test...

40 CFR 80.584 - What are the precision and accuracy criteria for approval of test methods for determining the...

Science.gov (United States)

2010-07-01

... criteria for approval of test methods for determining the sulfur content of motor vehicle diesel fuel, NRLM....584 What are the precision and accuracy criteria for approval of test methods for determining the... available gravimetric sulfur standard in the range of 1-10 ppm sulfur shall not differ from the accepted...

Technical operations procedure for assembly and emplacement of the soil temperature test--test assembly

International Nuclear Information System (INIS)

Weber, A.P.

1978-01-01

A description is given of the plan for assembly, instrumentation, emplacement, and operational checkout of the soil temperature test assembly and dry well liner. The activities described cover all operations necessary to accomplish the receiving inspection, instrumentation and pre-construction handling of the dry well liner, plus all operations performed with the test article. Actual details of construction work are not covered by this procedure. Each part and/or section of this procedure is a separate function to be accomplished as required by the nature of the operation. The organization of the procedure is not intended to imply a special operational sequence or schedular requirement. Specific procedure operational sections include: receiving inspection; liner assembly operations; construction operations (by others); prepare shield plug; test article assembly and installation; and operational checkout

Acceptance test procedure for High Pressure Water Jet System

International Nuclear Information System (INIS)

Crystal, J.B.

1995-01-01

The overall objective of the acceptance test is to demonstrate a combined system. This includes associated tools and equipment necessary to perform cleaning in the 105 K East Basin (KE) for achieving optimum reduction in the level of contamination/dose rate on canisters prior to removal from the KE Basin and subsequent packaging for disposal. Acceptance tests shall include necessary hardware to achieve acceptance of the cleaning phase of canisters. This acceptance test procedure will define the acceptance testing criteria of the high pressure water jet cleaning fixture. The focus of this procedure will be to provide guidelines and instructions to control, evaluate and document the acceptance testing for cleaning effectiveness and method(s) of removing the contaminated surface layer from the canister presently identified in KE Basin. Additionally, the desired result of the acceptance test will be to deliver to K Basins a thoroughly tested and proven system for underwater decontamination and dose reduction. This report discusses the acceptance test procedure for the High Pressure Water Jet

40 CFR 205.57-4 - Testing procedures.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Testing procedures. 205.57-4 Section 205.57-4 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) NOISE ABATEMENT PROGRAMS TRANSPORTATION EQUIPMENT NOISE EMISSION CONTROLS Medium and Heavy Trucks § 205.57-4 Testing...

Approval plans issues and innovations

CERN Document Server

Katz, Linda S

2013-01-01

How can you, as an acquisition librarians, keep current on the output of hundreds of publishers? The answer, of course, is that you cannot. For over 30 years, approval plans have been used by librarians to acquire current titles, save staff time, and build core collections. Even today, these reasons seem appropriate, as libraries try to maintain up-to-date collections and control personnel and operating budgets. However, as shown in Approval Plans: Issues and Innovations, the use of approval plans is not so simple and straightforward; their use is subject to complex procedures and policies--an

Enraf Series 854 advanced technology gauge (ATG) acceptance test procedure

International Nuclear Information System (INIS)

Huber, J.H.

1996-01-01

This Acceptance Test Procedure was written to test the Enraf Series 854 Advanced Technology Gauge (ATG) prior to installation in the Tank Farms. The procedure sets various parameters and verifies that the gauge is functional

Test Procedure - pumping system for caustic addition project

International Nuclear Information System (INIS)

Leshikar, G.A.

1994-01-01

This test procedure provides the requirements for sub-system testing and integrated operational testing of the submersible mixer pump and caustic addition equipment by WHC and Kaiser personnel at the Rotating Equipment Shop run-in pit (Bldg. 272E)

46 CFR 199.40 - Evaluation, testing and approval of lifesaving appliances and arrangements.

Science.gov (United States)

2010-10-01

... appliances and arrangements. 199.40 Section 199.40 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LIFESAVING APPLIANCES AND ARRANGEMENTS LIFESAVING SYSTEMS FOR CERTAIN INSPECTED VESSELS General § 199.40 Evaluation, testing and approval of lifesaving appliances and arrangements. (a) Each item of...

TMACS test procedure TP012: Panalarm software bridge

International Nuclear Information System (INIS)

Washburn, S.J.

1994-01-01

This Test Procedure addresses the testing of the functionality of the Tank Monitor and Control System (TMACS) Panalarm bridge software. The features to be tested are: Bridge Initialization Options; Bridge Communication; Bridge Performance; Testing Checksum Errors; and Testing Command Reject Errors. Only the first three could be tested; the last two have been deferred to a later date

Miracle drug: Brazil approves never-tested cancer medicine.

Science.gov (United States)

Kuchenbecker, Ricardo S; Mota, Daniel M

2017-07-01

Background Brazil recently approved synthetic phosphoetanolamine, a popularly dubbed 'cancer pill', a substance that has been shown to kill cancer cells in lab animal models but was not yet formally accessed in humans, and thus despite the existence of any evidence of its efficacy and safety. Methods The authors describe the recent decision of Brazil to aprove phosphoetanolamine in the context of growing 'judicialization' to promote access to medicines and thus reinforcing a growing sense of legal uncertainty. Results The approval of phosphoetanolamine despite the existence of any evidence of its efficacy and safety represents to the authors one of the saddest and surrealistic episodes in Brazil's recent public health history. Brazil's current economic crisis is fueling the 'judicialization' to promote access to medicines and thus reinforcing a growing sense of legal uncertainty in the context of rising economic constrains and a progressive failing state. The authors state that the Phosphoetanolamine's approval bill violates current legal prohibition of commercialisation of drugs without the Brazilian national drug regulatory agency's approval and thus may represent a potential menace to Brazil's pharmacogovernance and the country's governance to health technology assessment at the Brazilian national health systems. Conclusion Phosphoetanolamine's approval illustrates that the combination of flawed decision making, economic crisis and political interference may threaten weak governance mechanisms for drug regulation and health technology assessment and thus representing an extra burden in the sustainability of universal access-based national health systems.

Approval procedures for clinical trials in the field of radiation oncology; Genehmigungsverfahren klinischer Studien im Bereich der Radioonkologie

Energy Technology Data Exchange (ETDEWEB)

Simon, Monique; Buettner, Daniel [Deutsches Konsortium fuer Translationale Krebsforschung (DKTK), Dresden (Germany); Deutsches Krebsforschungszentrum (DKFZ), Heidelberg (Germany); Medizinische Fakultaet und Universitaetsklinikum Carl Gustav Carus, Technische Universitaet Dresden, Klinik fuer Strahlentherapie und Radioonkologie und OncoRay - Nationales Zentrum fuer Strahlenforschung in der Onkologie, Dresden (Germany); Habeck, Matthias; Habeck, Uta; Brix, Gunnar [Bundesamt fuer Strahlenschutz (BfS), Fachbereich Strahlenschutz und Gesundheit, Neuherberg (Germany); Krause, Mechthild; Baumann, Michael [Deutsches Konsortium fuer Translationale Krebsforschung (DKTK), Dresden (Germany); Deutsches Krebsforschungszentrum (DKFZ), Heidelberg (Germany); Medizinische Fakultaet und Universitaetsklinikum Carl Gustav Carus, Technische Universitaet Dresden, Klinik fuer Strahlentherapie und Radioonkologie und OncoRay - Nationales Zentrum fuer Strahlenforschung in der Onkologie, Dresden (Germany); Helmholtz-Zentrum Dresden - Rossendorf, Institut fuer Radioonkologie und OncoRay - Nationales Zentrum fuer Strahlenforschung in der Onkologie, Dresden (Germany); Willich, Normann [Universitaetsklinikum Muenster, Klinik fuer Strahlentherapie - Radioonkologie, Muenster (Germany); Wenz, Frederik [Universitaetsmedizin Mannheim, Medizinische Fakultaet Mannheim, Universitaet Heidelberg, Klinik fuer Strahlentherapie und Radioonkologie, Mannheim (Germany); Schmidberger, Heinz [Universitaetsmedizin Mainz, Klinik fuer Radioonkologie und Strahlentherapie, Mainz (Germany); Debus, Juergen [Universitaetsklinikum Heidelberg, Klinik fuer Radioonkologie und Strahlentherapie, Heidelberg (Germany); Noelling, Torsten

2015-12-15

Application of ionizing radiation for the purpose of medical research in Germany needs to be approved by the national authority for radiation protection (Bundesamt fuer Strahlenschutz, BfS). For studies in the field of radiation oncology, differentiation between use of radiation for ''medical care (Heilkunde)'' versus ''medical research'' frequently leads to contradictions. The aim of this article is to provide principle investigators, individuals, and institutions involved in the process, as well as institutional review or ethics committees, with the necessary information for this assessment. Information on the legal frame and the approval procedures are also provided. A workshop was co-organized by the German Society for Radiation Oncology (DEGRO), the Working Party for Radiation Oncology (ARO) of the German Cancer Society (DKG), the German Society for Medical Physics (DGMP), and the German Cancer Consortium (DKTK) in October 2013. This paper summarizes the results of the workshop and the follow-up discussions between the organizers and the BfS. Differentiating between ''Heilkunde'' which does not need to be approved by the BfS and ''medical research'' is whether the specific application of radiation (beam quality, dose, schedule, target volume, etc.) is a clinically established and recognized procedure. This must be answered by the qualified physician(s) (''fachkundiger Arzt'' according to German radiation protection law) in charge of the study and the treatments of the patients within the study, taking into consideration of the best available evidence from clinical studies, guidelines and consensus papers. Among the important parameters for assessment are indication, total dose, and fractionation. Radiation treatments applied outside clinical trials do not require approval by the BfS, even if they are applied within a randomized or nonrandomized clinical trial

76 FR 38992 - Approval and Promulgation of Air Quality Implementation Plans; Pennsylvania; Update to Materials...

Science.gov (United States)

2011-07-05

... for Pennsylvania. Since the publication of the last IBR update, EPA has approved the following... revision'' and ``Applicable geographic area'' columns for the entry ``Continuous Source Testing Manual.'' 2... section 553(b)(3)(B) of the Administrative Procedures Act (APA) which, upon finding ``good cause...

Approved reference and testing materials for use in Nuclear Waste Management Research and Development Programs

International Nuclear Information System (INIS)

Mellinger, G.B.; Daniel, J.L.

1984-12-01

This document, addressed to members of the waste management research and development community summarizes reference and testing materials available from the Nuclear Waste Materials Characterization Center (MCC). These materials are furnished under the MCC's charter to distribute reference materials essential for quantitative evaluation of nuclear waste package materials under development in the US. Reference materials with known behavior in various standard waste management related tests are needed to ensure that individual testing programs are correctly performing those tests. Approved testing materials are provided to assist the projects in assembling materials data base of defensible accuracy and precision. This is the second issue of this publication. Eight new Approved Testing Materials are listed, and Spent Fuel is included as a separate section of Standard Materials because of its increasing importance as a potential repository storage form. A summary of current characterization information is provided for each material listed. Future issues will provide updates of the characterization status of the materials presented in this issue, and information about new standard materials as they are acquired. 7 references, 1 figure, 19 tables

TMACS Test Procedure TP005: Sensor configuration, logging, and data conversion

International Nuclear Information System (INIS)

Washburn, S.J.

1994-01-01

The TMACS Software Project Test Procedures translate the projects acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes

14 CFR 21.8 - Approval of articles.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Approval of articles. 21.8 Section 21.8 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT CERTIFICATION PROCEDURES FOR PRODUCTS AND PARTS General § 21.8 Approval of articles. If an article is required to be...

Soil washing physical separations test procedure - 300-FF-1 operable unit

Energy Technology Data Exchange (ETDEWEB)

Belden, R.D.

1993-10-08

This procedure provides the operations approach, a field sampling plan, and laboratory procedures for a soil washing test to be conducted by Alternative Remedial Technologies, Inc. (ART) in the 300-FF-1 area at the Hanford site. The {open_quotes}Quality Assurance Project Plan for the Soil Washing Physical Separations Test, 300-FF-1 Operable Unit,{close_quotes} Hanford, Washington, Alternative Remedial Technologies, Inc., February 1994 (QAPP) is provided in a separate document that presents the procedural and organizational guidelines for this test. This document describes specifications, responsibilities, and general procedures to be followed to conduct physical separation soil treatability tests in the North Process Pond of the 300-FF-1 Operable Unit (OU) at the Hanford Site. These procedures are based on the {open_quotes}300-FF-1 Physical Separations CERCLA Treatability Test Plan, DOE/RL 92-2l,{close_quotes} (DOE-RL 1993).

Soil washing physical separations test procedure - 300-FF-1 operable unit

International Nuclear Information System (INIS)

Belden, R.D.

1993-01-01

This procedure provides the operations approach, a field sampling plan, and laboratory procedures for a soil washing test to be conducted by Alternative Remedial Technologies, Inc. (ART) in the 300-FF-1 area at the Hanford site. The open-quotes Quality Assurance Project Plan for the Soil Washing Physical Separations Test, 300-FF-1 Operable Unit,close quotes Hanford, Washington, Alternative Remedial Technologies, Inc., February 1994 (QAPP) is provided in a separate document that presents the procedural and organizational guidelines for this test. This document describes specifications, responsibilities, and general procedures to be followed to conduct physical separation soil treatability tests in the North Process Pond of the 300-FF-1 Operable Unit (OU) at the Hanford Site. These procedures are based on the open-quotes 300-FF-1 Physical Separations CERCLA Treatability Test Plan, DOE/RL 92-2l,close quotes (DOE-RL 1993)

A FLOW-THROUGH TESTING PROCEDURE WITH DUCKWEED (LEMNA MINOR L.)

Science.gov (United States)

Lemna minor is one of the smallest flowering plants. Because of its floating habit, ease of culture, and small size it is well adapted for laboratory investigations. Procedures for flow-through tests were developed. Testing procedures were developed with this apparatus. By using ...

Approved requirements for the packaging, labelling and carriage of radioactive material by rail

International Nuclear Information System (INIS)

1996-01-01

This document specifies the detailed provisions in the United Kingdom with respect to rail transport for packages and packaging, test procedures for radioactive materials, information concerning the preparation of radioactive materials and the operation of tanks and container wagons. The Approved Requirements came into force on 1 September 1996 and are legally binding. (UK)

Biaxial testing for fabrics and foils optimizing devices and procedures

CERN Document Server

Beccarelli, Paolo

2015-01-01

This book offers a well-structured, critical review of current design practice for tensioned membrane structures, including a detailed analysis of the experimental data required and critical issues relating to the lack of a set of design codes and testing procedures. The technical requirements for biaxial testing equipment are analyzed in detail, and aspects that need to be considered when developing biaxial testing procedures are emphasized. The analysis is supported by the results of a round-robin exercise comparing biaxial testing machines that involved four of the main research laboratories in the field. The biaxial testing devices and procedures presently used in Europe are extensively discussed, and information is provided on the design and implementation of a biaxial testing rig for architectural fabrics at Politecnico di Milano, which represents a benchmark in the field. The significance of the most recent developments in biaxial testing is also explored.

Quality assurance of radiopharmaceuticals-specifications and test procedures

International Nuclear Information System (INIS)

Baldas, J.; Bonnyman, J.; Pojer, P.M.

1981-08-01

This report is a compilation of test methods used and specifications adopted for the Radiopharmaceutical Quality Assurance Test Programme conducted by the Australian Radiation Laboratory. In some cases test procedures described have been taken from various Pharmacopoeias or methods published in the literature. In other cases test methods have been developed at the ARL

75 FR 36301 - Review and Approval of Projects

Science.gov (United States)

2010-06-25

... SUSQUEHANNA RIVER BASIN COMMISSION 18 CFR Parts 806 and 808 Review and Approval of Projects AGENCY... document contains proposed rules that would amend the project review regulations of the Susquehanna River... the scope of withdrawals requiring review and approval; improve notice procedures for all project...

Editorial: Ethics approval: responsibilities of journal editors, authors ...

African Journals Online (AJOL)

Meaningful progress of medicine depends on research that must ultimately involve human subjects. Obtaining ethical approval therefore, especially in medical sciences, should be a moral reflex for researchers. This unfortunately is not the case, with numerous researchers bypassing the ethics approval procedure, or simply ...

Quality assurance procedure for an industrial radiography linear accelerator

International Nuclear Information System (INIS)

Vishwakarma, R.R.; Kannan, R.; Yadav, R.K.

2001-01-01

Any radiation generating equipment can be marketed and used in India, only after obtaining specific type approval from the Competent Authority i.e. Chairman, Atomic Energy Regulatory Board (AERB). Generally linear accelerators are allowed to be used in the country based on the type approval issued by the regulatory authority of the country of its origin. So type approval of imported linear accelerators do not involve many parameters to be tested in our country. However for an indigenous accelerator, test procedures are to be defined and the same are to be followed during type approval process. No such protocol is available for linear accelerators used in industrial radiography. Recently some Indian manufacturers have started manufacturing and supplying such accelerators. A need for developing an indigenous protocol for type approval/NOC of such accelerators has arisen and the same has been developed. Various requirements for such protocol are discussed in this paper. Measurements have been performed on one of the 4 MV indigenous unit. Results of such measurements are also presented. Need for a regular periodic quality assurance program is necessary for imported as well as indigenous accelerators. A program for such quality assurance is also listed in the paper. (author)

Test plan/procedure for the SPM-1 shipping container system. Revision 0

International Nuclear Information System (INIS)

Flanagan, B.D.

1995-01-01

The 49 CFR 173.465 Type A packaging tests will verify that SPM-1 will provide adequate protection and pass as a Type A package. Test will determine that the handle of the Pig will not penetrate through the plywood spacer and rupture the shipping container. Test plan/procedure provides planning, pre-test, setup, testing, and post-testing guidelines and procedures for conducting the open-quotes Free Drop Testclose quotes procedure for the SPM-1 package

Vehicle accelerated corrosion test procedures for automotive in Malaysia

Directory of Open Access Journals (Sweden)

Anuar Liza

2017-01-01

Full Text Available An accelerated corrosion test, known as proving ground accelerated test, is commonly performed by automotive manufacturers to evaluate the corrosion performance of a vehicle. The test combines corrosion and durability inputs to detect potential failures that may occur during in-service conditions. Currently, the test is conducted at an external test center overseas. Such test is aimed to simulate the effects of one year accelerated corrosion in severe corrosive environment of the north-east and south east of America. However, the test results obtained do not correlate with the actual corrosion conditions observed in the Malaysian market, which is likely attributed to the different test environment of the tropical climate of vehicles in service. Therefore, a vehicle accelerated corrosion test procedure that suits the Malaysian market is proposed and benchmarked with other global car manufacturers that have their own dedicated corrosion test procedure. In the present work, a test track is used as the corrosion test ground and consists of various types of roads for structural durability exposures. Corrosion related facilities like salt trough, mud trough and gravel road are constructed as addition to the existing facilities. The establishment of accelerated corrosion test facilities has contributed to the development of initial accelerated corrosion test procedure for the national car manufacturer. The corrosion exposure is monitored by fitting test coupons at the underbody of test vehicle using mass loss technique so that the desired corrosion rate capable of simulating the real time corrosion effects for its target market.

40 CFR Appendix I to Subpart V of... - Recommended Test Procedures and Test Criteria and Recommended Durability Procedures To...

Science.gov (United States)

2010-07-01

... closing temperature shall be measured on an increasing temperature change. C. Carburetor Accelerator Pumps.... Reserved for Camshafts N. Reserved for Pistons O. Oxidizing Catalytic Converters 1. Test Procedures and...

40 CFR 80.585 - What is the process for approval of a test method for determining the sulfur content of diesel or...

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false What is the process for approval of a... voluntary consensus-based standards bodies. For such a method to be approved, the following information must... approved: Any test method approved by a voluntary consensus-based standards body, such as the American...

CANFLEX fuel bundle cross-flow endurance test 2 (test procedure)

Energy Technology Data Exchange (ETDEWEB)

Hong, Sung Deok; Chung, C. H.; Chang, S. K. [Korea Atomic Energy Research Institute, Taejon (Korea)

1999-04-01

This report describes test procedure of cross-flow 2 test for CANFLEX fuel. In October 1996. a cross-flow test was successfully performed in the KAERI Hot Test Loop for four hours at a water flow rate of 31kg/s, temperature of 266 deg C and inlet pressure of 11MPa, but it is requested more extended time periods to determine a realistic operational margin for the CANFLEX bundle during abnormal refuelling operations. The test shall be conducted for twenty two hours under the reactor conditions. After an initial period of ten hours, the test shall be stopped at the intervals of four hours for bundle inspection and inspect the test bundle end-plate to end-cap welds for failure or crack propagation using liquid penetrant examination. 2 refs., 1 fig. (Author)

40 CFR 86.1327-96 - Engine dynamometer test procedures; overview.

Science.gov (United States)

2010-07-01

... device, the exhaust pipe must be the same diameter as found in-use for at least 4 pipe diameters upstream... Exhaust Test Procedures § 86.1327-96 Engine dynamometer test procedures; overview. (a) The engine.... The exhaust emissions are diluted with ambient air and a continuous proportional sample is collected...

77 FR 28805 - Energy Conservation Program: Test Procedures for Microwave Ovens

Science.gov (United States)

2012-05-16

... Energy Conservation Program: Test Procedures for Microwave Ovens AGENCY: Office of Energy Efficiency and... (SNOPR) to amend the test procedures for microwave ovens. That SNOPR proposed amendments to the DOE test... mode energy use of products that combine a microwave oven with other appliance functionality, as well...

Environmental procedures

International Nuclear Information System (INIS)

1992-01-01

The European Bank has pledged in its Agreement to place environmental management at the forefront of its operations to promote sustainable economic development in central and eastern Europe. The Bank's environmental policy is set out in the document titled, Environmental Management: The Bank's Policy Approach. This document, Environmental Procedures, presents the procedures which the European Bank has adopted to implement this policy approach with respect to its operations. The environmental procedures aim to: ensure that throughout the project approval process, those in positions of responsibility for approving projects are aware of the environmental implications of the project, and can take these into account when making decisions; avoid potential liabilities that could undermine the success of a project for its sponsors and the Bank; ensure that environmental costs are estimated along with other costs and liabilities; and identify opportunities for environmental enhancement associated with projects. The review of environmental aspects of projects is conducted by many Bank staff members throughout the project's life. This document defines the responsibilities of the people and groups involved in implementing the environmental procedures. Annexes contain Environmental Management: The Bank's Policy Approach, examples of environmental documentation for the project file and other ancillary information

Development of an accelerated creep testing procedure for geosynthetics.

Science.gov (United States)

1997-09-01

The report presents a procedure for predicting creep strains of geosynthetics using creep tests at elevated temperatures. Creep testing equipment was constructed and tests were performed on two types of geosynthetics: High Density Polyethylene (HDPE)...

Acceptance test procedure: RMW Land Disposal Facility Project W-025

International Nuclear Information System (INIS)

Roscha, V.

1994-01-01

This ATP establishes field testing procedures to demonstrate that the electrical/instrumentation system functions as intended by design for the Radioactive Mixed Waste Land Disposal Facility. Procedures are outlined for the field testing of the following: electrical heat trace system; transducers and meter/controllers; pumps; leachate storage tank; and building power and lighting

Test Report for Acceptance Test Procedure for Pumping Instrumentation and Control Skid N

International Nuclear Information System (INIS)

KOCH, M.R.

2000-01-01

This is a Test Report for Acceptance Test Procedure (ATP) RPP-5489. This test report provides the results of the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''N''. The ATP was successfully completed. A copy of the completed ATP is in the Appendix of this document

Test Report for Acceptance Test Procedure for Pumping Instrumentation and Control Skid M

International Nuclear Information System (INIS)

KOCH, M.R.

1999-01-01

This is a Test Report for Acceptance Test Procedure (ATP) RPP-5073. This test report provides the results of the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''M''. The ATP was successfully completed. A copy of the completed ATP is in the Appendix of this document

Test Report for Acceptance Test Procedure for Pumping Instrumentation and Control Skid L

International Nuclear Information System (INIS)

KOCH, M.R.

1999-01-01

This is a Test Report for Acceptance Test Procedure (ATP) RPP-5055. This test report provides the results of the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''L''. The ATP was successfully completed. A copy of the completed ATP is in the Appendix of this document

702AZ aging waste ventilation facility year 2000 test procedure

International Nuclear Information System (INIS)

Winkelman, W.D.

1998-01-01

This test procedure was developed to determine if the 702AZ Tank Ventilation Facility system is Year 2000 Compliant. The procedure provides detailed instructions for performing the operations necessary and documenting the results. This verification procedure will document that the 702AZ Facility Systems are year 2000 compliant and will correctly meet the criteria established in this procedure

Test procedures for polyester immobilized salt-containing surrogate mixed wastes

International Nuclear Information System (INIS)

Biyani, R.K.; Hendrickson, D.W.

1997-01-01

These test procedures are written to meet the procedural needs of the Test Plan for immobilization of salt containing surrogate mixed waste using polymer resins, HNF-SD-RE-TP-026 and to ensure adequacy of conduct and collection of samples and data. This testing will demonstrate the use of four different polyester vinyl ester resins in the solidification of surrogate liquid and dry wastes, similar to some mixed wastes generated by DOE operations

30 CFR 90.206 - Approved sampling devices; equivalent concentrations.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Approved sampling devices; equivalent... LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-COAL MINERS WHO HAVE EVIDENCE OF THE DEVELOPMENT OF PNEUMOCONIOSIS Sampling Procedures § 90.206 Approved sampling devices; equivalent...

Operability test procedure [Tank] 241-SY-101 equipment removal system

International Nuclear Information System (INIS)

Mast, J.C.

1994-01-01

The 241-SY-101 equipment removal system (ERS) consists of components, equipment, instrumentation and procedures that will provide the means to disconnect, retrieve, contain, load and transport the Mitigation Pump Assembly (MPA) from waste Tank 241-SY-101 to the Central Waste Complex (CWC). The Operability Test Procedure (OTP) will test the interfaces between ERS components and will rehearse the procedure for MPA removal and transportation to the extent they can be mocked-up at the CTF (Cold Test Facility). At the conclusion of the OTP, the ERS components and equipment will be removed from the CTF, entered into the Component Based Recall System (CBRS), and stored until needed for actual MPA removal and transportation

A Tool for Predicting Regulatory Approval After Phase II Testing of New Oncology Compounds.

Science.gov (United States)

DiMasi, J A; Hermann, J C; Twyman, K; Kondru, R K; Stergiopoulos, S; Getz, K A; Rackoff, W

2015-11-01

We developed an algorithm (ANDI) for predicting regulatory marketing approval for new cancer drugs after phase II testing has been conducted, with the objective of providing a tool to improve drug portfolio decision-making. We examined 98 oncology drugs from the top 50 pharmaceutical companies (2006 sales) that first entered clinical development from 1999 to 2007, had been taken to at least phase II development, and had a known final outcome (research abandonment or regulatory marketing approval). Data on safety, efficacy, operational, market, and company characteristics were obtained from public sources. Logistic regression and machine-learning methods were used to provide an unbiased approach to assess overall predictability and to identify the most important individual predictors. We found that a simple four-factor model (activity, number of patients in the pivotal phase II trial, phase II duration, and a prevalence-related measure) had high sensitivity and specificity for predicting regulatory marketing approval. © 2015 American Society for Clinical Pharmacology and Therapeutics.

Procedures for Selecting Items for Computerized Adaptive Tests.

Science.gov (United States)

Kingsbury, G. Gage; Zara, Anthony R.

1989-01-01

Several classical approaches and alternative approaches to item selection for computerized adaptive testing (CAT) are reviewed and compared. The study also describes procedures for constrained CAT that may be added to classical item selection approaches to allow them to be used for applied testing. (TJH)

New energy test procedures for refrigerators and other appliances; FINAL

International Nuclear Information System (INIS)

Meier, Alan; Ernebrant, Stefan; Kawamoto, Kaoru; Wihlborg, Mats

1999-01-01

Many innovations in refrigerator design rely on microprocessors, sensors, and algorithms to control automatic defrost, variable speed,and other features. Even though these features strongly influence energy consumption, the major energy test procedures presently test only a refrigerator's mechanical efficiency and ignore the ''software'' aspects. We describe a new test procedure where both ''hardware'' and ''software'' tests are fed into a dynamic simulation model. A wide range of conditions can be tested and simulated. This approach promotes international harmonization because the simulation model can also be programmed to estimate energy use for the ISO, DOE, or JIS test. The approach outlined for refrigerators can also be applied to other appliances

Test Report for Acceptance Test Procedure for Pumping Instrumentation and Control Skid L

Energy Technology Data Exchange (ETDEWEB)

KOCH, M.R.

1999-11-09

This is a Test Report for Acceptance Test Procedure (ATP) RPP-5055. This test report provides the results of the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''L''. The ATP was successfully completed. A copy of the completed ATP is in the Appendix of this document.

Test Report for Acceptance Test Procedure for Pumping Instrumentation and Control Skid M

Energy Technology Data Exchange (ETDEWEB)

KOCH, M.R.

1999-12-13

This is a Test Report for Acceptance Test Procedure (ATP) RPP-5073. This test report provides the results of the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''M''. The ATP was successfully completed. A copy of the completed ATP is in the Appendix of this document.

12 CFR 211.24 - Approval of offices of foreign banks; procedures for applications; standards for approval...

Science.gov (United States)

2010-01-01

... combat money laundering. The Board also may take into account whether the home country supervisor is developing a legal regime to address money laundering or is participating in multilateral efforts to combat money laundering. In approving an application under this paragraph (c)(1)(iii), the Board, after...

Empirical testing of forecast update procedure forseasonal products

DEFF Research Database (Denmark)

Wong, Chee Yew; Johansen, John

2008-01-01

Updating of forecasts is essential for successful collaborative forecasting, especially for seasonal products. This paper discusses the results of a theoretical simulation and an empirical test of a proposed time-series forecast updating procedure. It involves a two-stage longitudinal case study...... of a toy supply chain. The theoretical simulation involves historical weekly consumer demand data for 122 toy products. The empirical test is then carried out in real-time with 291 toy products. The results show that the proposed forecast updating procedure: 1) reduced forecast errors of the annual...... provided less forecast accuracy improvement and it needed a longer time to achieve relatively acceptable forecast uncertainty....

40 CFR 53.43 - Test procedures.

Science.gov (United States)

2010-07-01

... sampling zone (see § 53.42(d)). To meet the maximum blockage limit of § 53.42(a) or for convenience, part... PM10 § 53.43 Test procedures. (a) Sampling effectiveness—(1) Technical definition. The ratio (expressed... evenly spaced isokinetic samplers in the sampling zone (see § 53.42(d)) of the wind tunnel. Collect...

40 CFR 600.111-08 - Test procedures.

Science.gov (United States)

2010-07-01

... § 600.109(b) while sampling the exhaust gas. (viii) Sampling must begin two seconds before beginning the... convenience of the user, the revised text is set forth as follows: § 600.111-08 Test procedures. (f) Special...

Parametric Sensitivity Tests—European Polymer Electrolyte Membrane Fuel Cell Stack Test Procedures

DEFF Research Database (Denmark)

Araya, Samuel Simon; Andreasen, Søren Juhl; Kær, Søren Knudsen

2014-01-01

performed based on test procedures proposed by a European project, Stack-Test. The sensitivity of a Nafion-based low temperature PEMFC stack’s performance to parametric changes was the main objective of the tests. Four crucial parameters for fuel cell operation were chosen; relative humidity, temperature......As fuel cells are increasingly commercialized for various applications, harmonized and industry-relevant test procedures are necessary to benchmark tests and to ensure comparability of stack performance results from different parties. This paper reports the results of parametric sensitivity tests......, pressure, and stoichiometry at varying current density. Furthermore, procedures for polarization curve recording were also tested both in ascending and descending current directions....

78 FR 694 - Proposed Extension of Approval of Information Collection; Comment Request-Testing and...

Science.gov (United States)

2013-01-04

... ignition of mattresses, 16 CFR part 1632. The Open- Flame standard is intended to reduce unreasonable risks... may be introduced into commerce. The Office of Management and Budget (OMB) previously approved the... suppliers, and confirmation test records, if establishments choose to pool a prototype. This documentation...

CEL Working procedures for WRAP 2A formulation development test

International Nuclear Information System (INIS)

Duchsherer, M.J.

1994-01-01

The WRAP 2A facility will encapsulate retrieved, stored, and newly generated contact-handled mixed low level waste (MLLW) into 55-500 gal cementitous forms. Standardized test procedures will be required to facilitate this process. Cementitous specimens will be prepared from simulated drum wastes and will be tested in the Chemical Engineering Laboratory using the laboratory operating/working procedures encorporated into this document

7 CFR 1737.41 - Procedure for obtaining approval.

Science.gov (United States)

2010-01-01

... RUS financing. (3) The proposed interim financing presents unacceptable loan security risks to RUS, or..., DEPARTMENT OF AGRICULTURE PRE-LOAN POLICIES AND PROCEDURES COMMON TO INSURED AND GUARANTEED TELECOMMUNICATIONS LOANS Interim Financing of Construction of Telephone Facilities § 1737.41 Procedure for obtaining...

Acceptance Test Procedure: SY101 air pallet system

International Nuclear Information System (INIS)

Koons, B.M.

1995-01-01

The purpose of this test procedure is to verify that the system(s) procured to load the SY-101 Mitigation Test Pump package fulfills its functional requirements. It will also help determine the man dose expected due to handling of the package during the actual event. The scope of this procedure focuses on the ability of the air pallets and container saddles to carry the container package from the new 100 foot concrete pad into 2403-WD where it will be stored awaiting final disposition. This test attempts to simulate the actual event of depositing the SY-101 hydrogen mitigation test pump into the 2403-WD building. However, at the time of testing road modifications required to drive the 100 ton trailer into CWC were not performed. Therefore a flatbed trailer will be use to transport the container to CWC. The time required to off load the container from the 100 ton trailer will be recorded for man dose evaluation on location. The cranes used for this test will also be different than the actual event. This is not considered to be an issue due to minimal effects on man dose

40 CFR 82.38 - Approved independent standards testing organizations.

Science.gov (United States)

2010-07-01

... Recycling Program Manager, Stratospheric Protection Division (6205J), U.S. Environmental Protection Agency... following: (1) That the organization has the capacity to accurately test whether refrigerant recycling... procedures are appropriate for that purpose. (2) That the organization has no conflict of interest and will...

Neurological Diagnostic Tests and Procedures

Science.gov (United States)

... and three-dimensional pictures of brain activity by measuring radioactive isotopes that are injected into the bloodstream. ... Legislative Updates Impact NINDS Contributions to Approved Therapies Strategic Plans & Evaluations Strategic Plans Program Evaluations Workforce Diversity ...

40 CFR 1065.12 - Approval of alternate procedures.

Science.gov (United States)

2010-07-01

... Compliance Officer an initial written request describing the alternate procedure and why you believe it is... described in this section, we may ask you to submit to us in writing supplemental information showing that... allowed procedure, considering the following factors: (1) The cost, difficulty, and availability to switch...

49 CFR 572.144 - Thorax assembly and test procedure.

Science.gov (United States)

2010-10-01

...-year-Old Child Crash Test Dummy, Alpha Version § 572.144 Thorax assembly and test procedure. (a) Thorax... displacement (compression) relative to the spine, measured with the chest deflection transducer (SA-572-S50...

78 FR 41609 - Energy Conservation Program for Consumer Products: Test Procedures for Refrigerators...

Science.gov (United States)

2013-07-10

... September 14, 1977. 42 FR 46140. Industry representatives viewed these test procedures as too complex and... Freezers'' (HRF-1- 1979). Using this industry-created test procedure, DOE revised its test procedures on... compartment of such a product to be at a level that would effectively exclude the coverage of combination wine...

78 FR 4015 - Energy Conservation Program: Test Procedures for Microwave Ovens

Science.gov (United States)

2013-01-18

... Conservation Program: Test Procedures for Microwave Ovens AGENCY: Office of Energy Efficiency and Renewable... microwave ovens. That SNOPR proposed amendments to the DOE test procedure to incorporate provisions from the... energy use of products that combine a microwave oven with other appliance functionality, as well as minor...

Recommended procedures for performance testing of radiobioassay laboratories: Volume 3, In vivo test phantoms

International Nuclear Information System (INIS)

MacLellan, J.A.; Traub, R.J.

1988-11-01

Draft American National Standards Institute (ANSI) Standard N13.30 (Performance Criteria for Radiobioassay) was developed for the US Department of Energy and the US Nuclear Regulatory Commission to help ensure that bioassay laboratories provide accurate and consistent results. The draft standard describes the procedures necessary to establish a bioassay performance-testing laboratory and program. The bioassay performance-testing laboratory will conduct tests to evaluate the performance of service laboratories. Pacific Northwest Laboratory helped develop testing procedures as part of an effort to evaluate the draft ANSI N13.30 performance criteria by testing the existing measurement capabilities of various bioassay laboratories. This report recommends guidelines for the preparation, handling, storage, distribution, shipping, and documentation of test phantoms used for calibration of measurement systems for direct bioassay. The data base and recommended records system for documenting radiobioassay performance at the service laboratories are also presented

Standard Ship Test and Inspection Plan, Procedures and Database

National Research Council Canada - National Science Library

1999-01-01

... construction schedules and increased cost is the area of test and inspection. This project investigates existing rules and regulations for testing and inspection of commercial ships and identifies differences and similarities within the requirements. The results include comparison matrices, a standard test plan, a set of standard test procedures, and a sample test database developed for a typical commercial ship.

Performance and Health Test Procedure for Grid Energy Storage Systems: Preprint

Energy Technology Data Exchange (ETDEWEB)

Baggu, Murali M [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Smith, Kandler A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Friedl, Andrew [San Diego Gas and Electric; Bialek, Thomas [San Diego Gas and Electric; Schimpe, Michael Robert [Technical University of Munich

2017-07-27

A test procedure to evaluate the performance and health of field installations of grid-connected battery energy storage systems (BESS) is described. Performance and health metrics captured in the procedures are: Round-trip efficiency, Standby losses, Response time/accuracy, and Useable Energy/ State of Charge at different discharge/charge rates over the system's lifetime. The procedures are divided into Reference Performance Tests, which require the system to be put in a test mode and are to be conducted in intervals, and Real-time Monitoring tests, which collect data during normal operation without interruption. The procedures can be applied on a wide array of BESS with little modifications and can thus support BESS operators in the management of BESS field installations with minimal interruption and expenditures.can be applied on a wide array of BESS with little modifications and can thus support BESS operators in the management of BESS field installations with minimal interruption and expenditures.

49 CFR 572.164 - Thorax assembly and test procedure.

Science.gov (United States)

2010-10-01

... Hybrid III Six-Year-Old Weighted Child Test Dummy § 572.164 Thorax assembly and test procedure. (a... specified in 49 CFR 572.124(c): (1) The maximum sternum displacement relative to the spine, measured with...

The influence of different measurement structures on NRTA test procedures

International Nuclear Information System (INIS)

Beedgen, R.

1986-01-01

The development of sequential statistical test procedures in the area of near real time material accountancy (NRTA) mostly assumed a fixed measurement model of a given model facility. In this paper different measurement models (dispersion matrices) for a sequence of balance periods are studied. They are used to compare the detection probabilities of three different sequential test procedures for losses of material. It is shown how different plant models have an influence on the sensitivity of specified tests. Great importance for that analysis have the optimal loss patterns in each measurement situation

Heavy-duty approval test cycles: assessment of currently applied test cycles and theories for the development of new duty cycles

NARCIS (Netherlands)

Weijer, C.J.T. van de; Rijkeboer, R.C.

1999-01-01

In the development of the new emission reduction technologies, the benefits of the use of these technologies must be assessed for real-life engine use. As in practice engines are developed to perform as good as possible on the approval test cycle on the basis of which emission limits are set, it is

16 CFR 1611.33 - Test procedures for textile fabrics and film.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Test procedures for textile fabrics and film... REGULATIONS STANDARD FOR THE FLAMMABILITY OF VINYL PLASTIC FILM Rules and Regulations § 1611.33 Test procedures for textile fabrics and film. (a)(1) All textile fabrics (except those with a nitro-cellulose...

FFTF operations procedures preparation guide. Revision 2

International Nuclear Information System (INIS)

1976-12-01

The Guide is intended to provide guidelines for the initial preparation of FFTF Operating Procedures. The Procedures Preparation Guide was developed from the plan presented and approved in the FFTF Reactor Plant Procedures Plan, PC-1, Revision 3

Test Operations Procedure (TOP) 08-2-188 Chemical Point Detector Vapor Testing

Science.gov (United States)

2018-04-27

Final 3. DATES COVERED (From - To) 4. TITLE AND SUBTITLE Test Operations Procedure (TOP) 08-2-188 Chemical Point Detector Vapor Testing 5a. CONTRACT...NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING...ORGANIZATION NAME(S) AND ADDRESS(ES) US Army Dugway Proving Ground West Desert Test Center (TEDT-DPW) Dugway, UT 84022-5000 8. PERFORMING ORGANIZATION

Acceptance test procedure for the 105-KW isolation barrier leak rate

International Nuclear Information System (INIS)

McCracken, K.J.

1995-01-01

This acceptance test procedure shall be used to: First establish a basin water loss rate prior to installation of the two isolation barriers between the main basin and the discharge chute in K-Basin West. Second, perform an acceptance test to verify an acceptable leakage rate through the barrier seals. This Acceptance Test Procedure (ATP) has been prepared in accordance with CM-6-1 EP 4.2, Standard Engineering Practices

European wind turbine testing procedure developments. Task 2: Power quality

DEFF Research Database (Denmark)

Sørensen, Poul Ejnar; Friis Pedersen, Troels; Gerdes, G.

2001-01-01

The present report describes the work done in the power quality subtask of the European Wind Turbine Testing Procedure Developments project funded by the EU SMT program. The objective of the power quality subtask has been to make recommendations andprovide background for new standards...... for measurement and testing of wind turbine power quality. The focus in the work has been to support the ongoing standardisation work in IEC with a new standard IEC61400-21 for measurement and assessment of powerquality characteristics of grid connected wind turbines. The work has also been based on the power...... quality measuremnet procedure in the Measnet cooperation of European test stations for wind turbines. The first working item of the project has been toverify the state of the art of the measurement procedures by analyses and comparisons of the measurements and data processing software of the participating...

Loss on Ignition Furnace Acceptance and Operability Test Procedure

Energy Technology Data Exchange (ETDEWEB)

JOHNSON, D.C.

2000-06-01

The purpose of this Acceptance Test Procedure and Operability Test Procedure (ATP/OTP)is to verify the operability of newly installed LOI equipment, including a model 1608FL CM{trademark} Furnace, a dessicator, and balance. The operability of the furnace will be verified. The arrangement of the equipment placed in Glovebox 157-3/4 to perform Loss on Ignition (LOI) testing on samples supplied from the Thermal Stabilization line will be verified. In addition to verifying proper operation of the furnace, this ATP/OTP will also verify the air flow through the filters, verify a damper setting to establish and maintain the required differential pressure between the glovebox and the room pressure, and test the integrity of the newly installed HEPA filter. In order to provide objective evidence of proper performance of the furnace, the furnace must heat 15 crucibles, mounted on a crucible rack, to 1000 C, according to a program entered into the furnace controller located outside the glovebox. The glovebox differential pressure will be set to provide the 0.5 to 2.0 inches of water (gauge) negative pressure inside the glovebox with an airflow of 100 to 125 cubic feet per minute (cfm) through the inlet filter. The glovebox inlet Glfilter will he flow tested to ensure the integrity of the filter connections and the efficiency of the filter medium. The newly installed windows and glovebox extension, as well as all disturbed joints, will be sonically tested via ultra probe to verify no leaks are present. The procedure for DOS testing of the filter is found in Appendix A.

TMACS test procedure TP005: Sensor configuration, logging, and data conversion. Revision 4

International Nuclear Information System (INIS)

Washburn, S.J.

1994-01-01

The TMACS Software Project Test Procedures translate the project's acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes. This Test Procedure addresses the sensor configuration, conversion and logging requirements of the TMACS. The features to be tested are as follows: sensor configuration data; conversion of continuous sensor data to engineering units; conversion of digital data to discrete states; discrete sensor data logging; and continuous sensor data logging

34 CFR 668.149 - Special provisions for the approval of assessment procedures for special populations for whom no...

Science.gov (United States)

2010-07-01

... procedure or instrument measures both basic verbal and quantitative skills at the secondary school level. (2... recommended by the test developer, provided that the test administrator— (i) Uses those procedures or... verbal and quantitative skills at the secondary school level; and (4) The passing scores and the methods...

Acceptance test procedure for core sample trucks

International Nuclear Information System (INIS)

Smalley, J.L.

1995-01-01

The purpose of this Acceptance Test Procedure is to provide instruction and documentation for acceptance testing of the rotary mode core sample trucks, HO-68K-4600 and HO-68K-4647. The rotary mode core sample trucks were based upon the design of the second core sample truck (HO-68K-4345) which was constructed to implement rotary mode sampling of the waste tanks at Hanford. Acceptance testing of the rotary mode core sample trucks will verify that the design requirements have been met. All testing will be non-radioactive and stand-in materials shall be used to simulate waste tank conditions. Compressed air will be substituted for nitrogen during the majority of testing, with nitrogen being used only for flow characterization

40 CFR 1065.520 - Pre-test verification procedures and pre-test data collection.

Science.gov (United States)

2010-07-01

... corrective action does not resolve the deficiency, you may request to use the contaminated system as an... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Pre-test verification procedures and pre-test data collection. 1065.520 Section 1065.520 Protection of Environment ENVIRONMENTAL PROTECTION...

30 CFR 90.204 - Approved sampling devices; maintenance and calibration.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Approved sampling devices; maintenance and... LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-COAL MINERS WHO HAVE EVIDENCE OF THE DEVELOPMENT OF PNEUMOCONIOSIS Sampling Procedures § 90.204 Approved sampling devices; maintenance and...

Test Procedure for Axially Loaded Bucket Foundations in Sand (Large Yellow Box)

DEFF Research Database (Denmark)

Vaitkunaite, Evelina

This is a practical guide for preparing the soil, running a CPT test, installing a scaled bucket foundation model and running a test in the large yellow sand box cos(Kristina) in the geotechnical laboratory at Aalborg University. The test procedure is used for the examination of statically...... and cyclically axially loaded bucket foundation model In dense sand. The foundation model in scale of approximately 1:10 compared to the prototype size. The guide describes the step-by-step procedure for tests with and without surface pressure. A detailed description of test setup using the large yellow sand box...... for a monopile testing was provided by Thomassen (2015a), procedure for monopile testing can be found in Thomassen (2015b), while safety instructions were given by Vaitkunaite et al. (2014)....

Development of Start-up and Shutdown Procedure for the HANARO Fuel Test Loop

International Nuclear Information System (INIS)

Park, S. K.; Sim, B. S.; Chi, D. Y.; Lee, J. M.; Lee, C. Y.; Ahn, S. H.

2009-06-01

A start-up and shutdown procedure for the HANARO fuel test loop has been developed. This is a facility for fuel and material irradiation tests. The facility provides experimental conditions similar to the normal operational pressures and temperatures of commercial PWR and CANDU plants. The normal operation modes of the HANARO fuel test loop are classified into loop shutdown, cold stand-by 1, cold stand-by 2, hot stand-by, and hot operation. The operation modes depend on the fission power of test fuels and the coolant temperature at the inlet of the in-pile test section. The HANARO must maintain a shutdown mode if the HANARO fuel test loop is loop shutdown, cold stand-by 1, cold stand-by 2, or hot stand-by. As the HANARO becomes power operation mode, the operation mode of the HANARO fuel test loop comes to hot operation from hot stand-by. The procedure for the HANARO fuel test loop consists of four main parts such as check of initial conditions, stat-up operation procedure, shutdown operation procedure, and check lists for operations. Several hot test operations ensure that the procedure is appropriate

Bariatric Surgery Procedures

Science.gov (United States)

... Meetings of Interest Online Education Job Board CME Policies CBN Fellowship Certificate Research Grant Program Resources All Resources Approved Procedures Patient Safety Vignettes Dr. Mason Historical Library Governing Documents Guidelines Access and Insurance Position and ...

16 CFR 1209.7 - Test procedures for smoldering combustion.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Test procedures for smoldering combustion. 1209.7 Section 1209.7 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION CONSUMER PRODUCT SAFETY... for smoldering combustion. This section provides the test method for determining smoldering combustion...

30 CFR 90.205 - Approved sampling devices; operation; air flowrate.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Approved sampling devices; operation; air... LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-COAL MINERS WHO HAVE EVIDENCE OF THE DEVELOPMENT OF PNEUMOCONIOSIS Sampling Procedures § 90.205 Approved sampling devices; operation; air flowrate...

Loss on Ignition Furnace Acceptance and Operability Test Procedure

International Nuclear Information System (INIS)

JOHNSTON, D.C.

2000-01-01

The purpose of this Acceptance Test Procedure and Operability Test Procedure (ATP/OTP)is to verify the operability of newly installed Loss on Ignition (LOI) equipment, including a model 1608FL CMTM Furnace, a dessicator, and balance. The operability of the furnace will be verified. The arrangement of the equipment placed in Glovebox 157-3/4 to perform LOI testing on samples supplied from the Thermal Stabilization line will be verified. In addition to verifying proper operation of the furnace, this ATP/OTP will also verify the air flow through the filters, verify a damper setting to establish and maintain the required differential pressure between the glovebox and the room pressure, and test the integrity of the newly installed HEPA filter. In order to provide objective evidence of proper performance of the furnace, the furnace must heat 15 crucibles, mounted on a crucible rack, to 1000 C, according to a program entered into the furnace controller located outside the glovebox. The glovebox differential pressure will be set to provide the 0.5 to 2.0 inches of water (gauge) negative pressure inside the glovebox with an expected airflow of 100 to 125 cubic feet per minute (cfm) through the inlet filter. The glovebox inlet G1 filter will be flow tested to ensure the integrity of the filter connections and the efficiency of the filter medium. The newly installed windows and glovebox extension, as well as all disturbed joints, will be sonically tested via ultra probe to verify no leaks are present. The procedure for DOS testing of the filter is found in Appendix A

Building Energy Simulation Test for Existing Homes (BESTEST-EX); Phase 1 Test Procedure: Building Thermal Fabric Cases

Energy Technology Data Exchange (ETDEWEB)

Judkoff, R.; Polly, B.; Bianchi, M.; Neymark, J.

2010-08-01

The U.S. Department of Energy tasked NREL to develop a process for testing the reliability of models that predict retrofit energy savings, including their associated calibration methods. DOE asked NREL to conduct the work in phases so that a test procedure would be ready should DOE need it to meet legislative requirements related to residential retrofits in FY 2010. This report documents the initial 'Phase 1' test procedure.

Program Baseline Change Control Procedure

International Nuclear Information System (INIS)

1993-02-01

This procedure establishes the responsibilities and process for approving initial issues of and changes to the technical, cost, and schedule baselines, and selected management documents developed by the Office of Civilian Radioactive Waste Management (OCRWM) for the Civilian Radioactive Waste Management System. This procedure implements the OCRWM Baseline Management Plan and DOE Order 4700.1, Chg 1. It streamlines the change control process to enhance integration, accountability, and traceability of Level 0 and Level I decisions through standardized Baseline Change Proposal (BCP) forms to be used by the Level 0, 1, 2, and 3 Baseline Change Control Boards (BCCBs) and to be tracked in the OCRWM-wide Configuration Information System (CIS) Database.This procedure applies to all technical, cost, and schedule baselines controlled by the Energy System Acquisition Advisory Board (ESAAB) BCCB (Level 0) and, OCRWM Program Baseline Control Board (PBCCB) (Level 1). All baseline BCPs initiated by Level 2 or lower BCCBs, which require approval from ESAAB or PBCCB, shall be processed in accordance with this procedure. This procedure also applies to all Program-level management documents controlled by the OCRWM PBCCB

Test Procedure for Axially Loaded Piles in Sand

DEFF Research Database (Denmark)

Thomassen, Kristina

The test procedure described in the following is used when examining the effects of static or cyclic loading on the skin friction of an axially loaded pile in dense sand. The pile specimen is only loaded in tension to avoid any contribution from the base resistance. The pile dimensions are chosen...... to resemble full scale dimension of piles used in offshore pile foundations today. In this report is given a detailed description of the soil preparation and pile installation procedures as well data acquisition methods....

76 FR 47178 - Energy Efficiency Program: Test Procedure for Lighting Systems (Luminaires)

Science.gov (United States)

2011-08-04

... DEPARTMENT OF ENERGY [Docket Number EERE-2011-BT-TP-0041] RIN 1904-AC50 Energy Efficiency Program: Test Procedure for Lighting Systems (Luminaires) AGENCY: Office of Energy Efficiency and Renewable... (``DOE'' or the ``Department'') is currently evaluating energy efficiency test procedures for luminaires...

Test procedures, AN/AIC-27 system and component units. [for space shuttle

Science.gov (United States)

Reiff, F. H.

1975-01-01

The AN/AIC-27 (v) intercommunication system is a 30-channel audio distribution which consists of: air crew station units, maintenance station units, and a central control unit. A test procedure for each of the above units and also a test procedure for the system are presented. The intent of the test is to provide data for use in shuttle audio subsystem design.

75 FR 38422 - Procedures for Transportation Workplace Drug and Alcohol Testing Programs

Science.gov (United States)

2010-07-02

... 2105-AD84 Procedures for Transportation Workplace Drug and Alcohol Testing Programs AGENCY: Office of..., 2011. DATES: This rule is effective July 2, 2010. FOR FURTHER INFORMATION CONTACT: For program issues... Federal Regulations, as follows: PART 40--PROCEDURES FOR TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING...

Preanalytical errors in primary healthcare: a questionnaire study of information search procedures, test request management and test tube labelling.

Science.gov (United States)

Söderberg, Johan; Brulin, Christine; Grankvist, Kjell; Wallin, Olof

2009-01-01

Most errors in laboratory medicine occur in the preanalytical phase and are the result of human mistakes. This study investigated information search procedures, test request management and test tube labelling in primary healthcare compared to the same procedures amongst clinical laboratory staff. A questionnaire was completed by 317 venous blood sampling staff in 70 primary healthcare centres and in two clinical laboratories (response rate = 94%). Correct procedures were not always followed. Only 60% of the primary healthcare staff reported that they always sought information in the updated, online laboratory manual. Only 12% reported that they always labelled the test tubes prior to drawing blood samples. No major differences between primary healthcare centres and clinical laboratories were found, except for test tube labelling, whereby the laboratory staff reported better practices. Re-education and access to documented routines were not clearly associated with better practices. The preanalytical procedure in the surveyed primary healthcare centres was associated with a risk of errors which could affect patient safety. To improve patient safety in laboratory testing, all healthcare providers should survey their preanalytical procedures and improve the total testing process with a systems perspective.

Military Publications, Index of Test Operations Procedures

Science.gov (United States)

1981-10-01

serial number, aad design information for majur components. Prescribes vehicle, major component, and system descrip- tive elements required; such as...mount operating characteristics. Discusses preparation for test, instrumentation, and facil- ities. Describes procedures for force measurement, carriage...backlash and accuracy, turret friction, gun balance, manual handcrank force , manual response ratio, weapon and sighting system backlash, power controller

10 CFR 431.193 - Test procedures for measuring energy consumption of distribution transformers.

Science.gov (United States)

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Test procedures for measuring energy consumption of distribution transformers. 431.193 Section 431.193 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY... § 431.193 Test procedures for measuring energy consumption of distribution transformers. The test...

Laparoscopic Stephen-Fowler stage procedure: appropriate management for high intra-abdominal testes.

Science.gov (United States)

Agrawal, Amit; Joshi, Milind; Mishra, Pankaj; Gupta, Rahul; Sanghvi, Beejal; Parelkar, Sandesh

2010-03-01

The length of testicular vessels is the main length-limiting factor to bring down the testes in the scrotum. Fowler and Stephen proposed the division of testicular vessels, high and as far from the testes as possible to maintain collateral blood supply, to treat high intra-abdominal testes. Cortesi introduced the diagnostic laparoscopy and Jorden first did the laparoscopic orchiopexy for nonpalpable testes. We had done Fowler-Stephen staged orchiopexy for high intra-abdominal testes, in which both stages were done laparoscopically. In total, 17 testes of 13 patients had undergone laparoscopic staged Fowler-Stephen orchiopexy. The decision to perform a staged Fowler-Stephen orchiopexy was based on the distance of the testis from the deep inguinal ring on laparoscopy. If distance was more than 2.5 cm, then we proceeded to a laparoscopic staged Fowler-Stephen orchiopexy. In the first stage, testicular vessels were cauterized by bipolar diathermy. Laparoscopic second-stage Fowler-Stephen procedure was done 6 months after the first stage. Patients were regularly followed, and the success of the procedure was assessed by the size of the testes and the position in the scrotum. Testicular vascularity was assessed by color Doppler ultrasonography. There was no testicular atrophy on second stage and on follow-up. All testes were in the scrotum with good size on follow-up. There was no complication related to laparoscopy. In cases of high intra-abdominal testes, the staged Fowler-Stephen procedure should be the procedure of choice. This procedure yields a high success rate. Transaction of vessels by bipolar diathermy is a very safe, cost-effective method.

Characterization of spent fuel approved testing material: ATM-106

International Nuclear Information System (INIS)

Guenther, R.J.; Blahnik, D.E.; Campbell, T.K.; Jenquin, U.P.; Mendel, J.E.; Thornhill, C.K.

1988-10-01

The characterization data obtained to date are described for Approved Testing Material (ATM)-106 spent fuel from Assembly BT03 of pressurized-water reactor Calvert Cliffs No. 1. This report is one in a series being prepared by the Materials Characterization Center at Pacific Northwest Laboratory on spent fuel ATMs. The ATMs are receiving extensive examinations to provide a source of well- characterized spent fuel for testing in the US Department of Energy Office of Civilian Radioactive Waste Management (OCWRM) program. ATM-106 consists of 20 full-length irradiated fuel rods with rod-average burnups of about 3700 GJ/kgM (43 MWd/kgM) and expected fission gas release of /approximately/10%. Characterization data include (1) as-fabricated fuel design, irradiation history, and subsequent storage and handling; (2) isotopic gamma scans; (3) fission gas analyses; (4) ceramography of the fuel and metallography of the cladding; (5) calculated nuclide inventories and radioactivities in the fuel and cladding; and (6) radiochemical analyses of the fuel and cladding. Additional analyses of the fuel rod are being conducted and will be included in planned revisions of this report. 12 refs., 110 figs., 81 tabs

118-B-1 excavation treatability test procedures

International Nuclear Information System (INIS)

Frain, J.M.

1994-01-01

This treatability study has two purposes: to support development of the approach to be used for burial ground remediation, and to provide specific engineering information for the design of burial grounds receiving waste generated from the 100 Area removal actions. Data generated from this test will also provide performance and cost information necessary for detailed analysis of alternatives for burial ground remediation. Further details on the test requirements, milestones and data quality objectives are described in detail in the 118-B-1 Excavation Treatability Test Plan (DOE/RL-94-43). These working procedures are intended for use by field personnel to implement the requirements of the milestone. A copy of the detailed Test Plan will be kept on file at the on-site field support trailer, and will be available for review by field personnel

10 CFR 431.16 - Test procedures for the measurement of energy efficiency.

Science.gov (United States)

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Test procedures for the measurement of energy efficiency. 431.16 Section 431.16 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY EFFICIENCY PROGRAM FOR... Methods of Determining Efficiency § 431.16 Test procedures for the measurement of energy efficiency. For...

100 Area soil washing bench-scale test procedures

International Nuclear Information System (INIS)

Freeman, H.D.; Gerber, M.A.; Mattigod, S.V.; Serne, R.J.

1993-03-01

This document describes methodologies and procedures for conducting soil washing treatability tests in accordance with the 100 Area Soil Washing Treatability Test Plan (DOE-RL 1992, Draft A). The objective of this treatability study is to evaluate the use of physical separation systems and chemical extraction methods as a means of separating chemically and radioactively contaminated soil fractions from uncontaminated soil fractions. These data will be primarily used for determining feasibility of the individual unit operations and defining the requirements for a system, or systems, for pilot-scale testing

Operator coil monitoring Acceptance Test Procedure

International Nuclear Information System (INIS)

Erhart, M.F.

1995-01-01

The readiness of the Data Acquisition and Control System (DACS) to provide monitoring and control of the Programmable Logic Controller (PLC) abort coils from the Master and RSS stations will be systematically tested during performance of this procedure. It should be noted that these are not physical abort coils but software coils controlled by the software's ladder logic. The readiness of the DACS to properly interface with the ENRAF wire level gauge installed in the SY-101 storage tank will also be tested. During this test, a verification of all abort coil indications will be conducted at the DACS Development Facility in the 306E Building by injecting an input signal for each DACS sensor that has an associated abort coil until the abort coil actuates, and then ensuring that the status of the abort coil indicated at the Master and RSS stations is correct. Each abort coil will also be tested to ensure that the ''ENABLE'' and ''DISABLE'' controls from the Master and RSS stations function correctly, and only with the use of proper passwords

9 CFR 147.8 - Procedures for preparing egg yolk samples for diagnostic tests.

Science.gov (United States)

2010-01-01

... samples for diagnostic tests. 147.8 Section 147.8 Animals and Animal Products ANIMAL AND PLANT HEALTH... IMPROVEMENT PLAN Blood Testing Procedures § 147.8 Procedures for preparing egg yolk samples for diagnostic... for diagnostic testing. (b) The authorized laboratory must identify each egg as to the breeding flock...

77 FR 49063 - Energy Conservation Program: Test Procedures for Residential Dishwashers and Cooking Products

Science.gov (United States)

2012-08-15

... Energy Conservation Program: Test Procedures for Residential Dishwashers and Cooking Products; Proposed...-AC01 Energy Conservation Program: Test Procedures for Residential Dishwashers and Cooking Products... procedures for both dishwashers and conventional cooking products for the measurement of energy use in fan...

75 FR 15645 - Approval and Promulgation of Air Quality Implementation Plans; Texas; Revisions to the Emission...

Science.gov (United States)

2010-03-30

... clarify EPA's role in the approval of emission quantification protocols. While the previous SIP- approved... approve severable portions of two revisions to the Texas State Implementation Plan (SIP) submitted by the... to further clarify procedures for using emission protocols and to update the approved list of...

Developing a Cloze Procedure as a Reading Comprehension Achievement Test

Directory of Open Access Journals (Sweden)

I Ketut Seken

2004-01-01

Full Text Available The project was concerned with developing a cloze procedure as a reading comprehension achievement test. The subjects were students of the English Department of the Faculty of Letters, State University of Malang, who were halfway in the semester to complete Reading II course. The test was planned and constructed on the foundation of existing theory of cloze test construction. A review of theory concerning reading comprehension, testing reading comprehension, and cloze testing led to the construction of the test, including the decision concerning how to score the test and to interpret the scores. Using a class of 28 students, the test was tried out a week after the mid-semester test was administered by the Reading II teacher. It was found that the test is sufficienty reliable on the basis of a reliability coefficient of .79 through split-half procedure and a coefficient value of .78 by K-R 20. The test also showed high inter-section correlation. The validity of the test was viewed in terms of face, content, and construct. The test scores correlate moderately with those obtained from the mid-semester test by the teacher. Some problems are discussed and a suggestion made with regard to a possible solution to these problems.

77 FR 74559 - Energy Conservation Program for Consumer Products: Test Procedures for Residential Water Heaters...

Science.gov (United States)

2012-12-17

... Conservation Program for Consumer Products: Test Procedures for Residential Water Heaters, Direct Heating... Energy (DOE) is amending its test procedures for residential water heaters, direct heating equipment (DHE... necessary for residential water heaters, because the existing test procedures for those products already...

76 FR 56347 - Energy Conservation Program for Consumer Products: Test Procedures for Residential Water Heaters...

Science.gov (United States)

2011-09-13

... Conservation Program for Consumer Products: Test Procedures for Residential Water Heaters, Direct Heating... proposed to amend, where appropriate, its test procedures for residential water heaters, direct heating... notes that the test procedure and metric for residential water heaters currently address and incorporate...

Laboratory procedures for waste form testing

International Nuclear Information System (INIS)

Mast, E.S.

1994-01-01

The 100 and 300 areas of the Hanford Site are included on the US Environmental Protection Agencies (EPA) National Priorities List under the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). Soil washing is a treatment process that is being considered for the remediation of the soil in these areas. Contaminated soil washing fines can be mixed or blended with cementations materials to produce stable waste forms that can be used for beneficial purposes in mixed or low-level waste landfills, burial trenches, environmental restoration sites, and other applications. This process has been termed co-disposal. The Co-Disposal Treatability Study Test Plan is designed to identify a range of cement-based formulations that could be used in disposal efforts in Hanford in co-disposal applications. The purpose of this document is to provide explicit procedural information for the testing of co-disposal formulations. This plan also provides a discussion of laboratory safety and quality assurance necessary to ensure safe, reproducible testing in the laboratory

Laboratory procedures for waste form testing

Energy Technology Data Exchange (ETDEWEB)

Mast, E.S.

1994-09-19

The 100 and 300 areas of the Hanford Site are included on the US Environmental Protection Agencies (EPA) National Priorities List under the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). Soil washing is a treatment process that is being considered for the remediation of the soil in these areas. Contaminated soil washing fines can be mixed or blended with cementations materials to produce stable waste forms that can be used for beneficial purposes in mixed or low-level waste landfills, burial trenches, environmental restoration sites, and other applications. This process has been termed co-disposal. The Co-Disposal Treatability Study Test Plan is designed to identify a range of cement-based formulations that could be used in disposal efforts in Hanford in co-disposal applications. The purpose of this document is to provide explicit procedural information for the testing of co-disposal formulations. This plan also provides a discussion of laboratory safety and quality assurance necessary to ensure safe, reproducible testing in the laboratory.

46 CFR 160.151-29 - Additional approval tests for SOLAS A and SOLAS B inflatable liferafts.

Science.gov (United States)

2010-10-01

... (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT... appendage must be attached to a testing jig similar in material and construction to the appendage's intended... water. The dry weight must be recorded. (2) The appendage and jig must then be quickly lowered into the...

27 CFR 5.51 - Label approval and release.

Science.gov (United States)

2010-04-01

..., DEPARTMENT OF THE TREASURY LIQUORS LABELING AND ADVERTISING OF DISTILLED SPIRITS Requirements for Withdrawal..., and revocation of certificates of label approval, as well as appeal procedures, see part 13 of this...

INERT Atmosphere confinement operability test procedure

International Nuclear Information System (INIS)

RISENMAY, H.R.

1999-01-01

This Operability Test Procedure (OTP) provides instructions for testing operability of the Inert Atmosphere Confinement (IAC). The Inert Atmosphere Confinement was designed and built for opening cans of metal items that might have hydrided surfaces. Unreviewed Safety Question (USQ) PFP-97-005 addresses the discovery of suspected plutonium hydride forming on plutonium metal currently stored in the Plutonium Finishing Plant vaults. Plutonium hydride reacts quickly with air, liberating energy. The Inert Atmosphere Confinement was designed to prevent this sudden liberation of energy by opening the material in an inert argon atmosphere instead of the normal glovebox atmosphere. The IAC is located in glovebox HC-21A, room 230B of the 234-5Z Building at the Plutonium Finishing Plant (PFP) in the 200-West Area of the Hanford Site

Applied field test procedures on petroleum release sites

International Nuclear Information System (INIS)

Gilbert, G.; Nichols, L.

1995-01-01

The effective remediation of petroleum contaminated soils and ground water is a significant issue for Williams Pipe Line Co. (Williams): costing $6.8 million in 1994. It is in the best interest, then, for Williams to adopt approaches and apply technologies that will be both cost-effective and comply with regulations. Williams has found the use of soil vapor extraction (SVE) and air sparging (AS) field test procedures at the onset of a petroleum release investigation/remediation accomplish these goals. This paper focuses on the application of AS/SVE as the preferred technology to a specific type of remediation: refined petroleum products. In situ field tests are used prior to designing a full-scale remedial system to first validate or disprove initial assumptions on applicability of the technology. During the field test, remedial system design parameters are also collected to tailor the design and operation of a full-scale system to site specific conditions: minimizing cost and optimizing effectiveness. In situ field tests should be designed and operated to simulate as close as possible the operation of a full-scale remedial system. The procedures of an in situ field test will be presented. The results of numerous field tests and the associated costs will also be evaluated and compared to full-scale remedial systems and total project costs to demonstrate overall effectiveness. There are many advantages of As/SVE technologies over conventional fluid extraction or SVE systems alone. However, the primary advantage is the ability to simultaneously reduce volatile and biodegradable compound concentrations in the phreatic, capillary fringe, and unsaturated zones

Operational test procedure for SY tank farm replacement exhauster unit

International Nuclear Information System (INIS)

McClees, J.

1995-01-01

This operational test procedure will verify that the remaining functions not tested per WHC-SD-WM-ATP-080, or components disturbed during final installation, as well as interfaces with other tank farm equipment and remote monitoring stations are operating correctly

40 CFR 86.159-00 - Exhaust emission test procedures for US06 emissions.

Science.gov (United States)

2010-07-01

... run on a large single roll electric dynamometer, or an approved equivalent dynamometer configuration... validity, shall be supplied on request of the Administrator. (6) The drive wheel tires may be inflated up... psi, in order to prevent tire damage. The drive wheel tire pressure shall be reported with the test...

40 CFR 86.227-94 - Test procedures; overview.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Test procedures; overview. 86.227-94 Section 86.227-94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... 1994 and Later Model Year Gasoline-Fueled New Light-Duty Vehicles, New Light-Duty Trucks and New Medium...

Frequency modulation system test procedure shuttle task 501 approach and landing test configuration

Science.gov (United States)

Doland, G. D.

1976-01-01

Shuttle Task 501 is an in-line task to test the performance and compatibility of radiofrequency links between the SSO and ground, and relay via a satellite. Under Shuttle Task 501 approach and landing test (ALT) phase only a limited portion of the communication and tracking (C&T) equipment is to be tested. The principal item to be tested is a frequency modulated (FM) data link. To test this RF link, an ALT FM System was designed, constructed, and the console wiring verified. A step-by-step procedure to be used to perform the ALT FM system is presented. The ALT FM system test is to be performed prior to delivery of the equipment to the Electronic Systems Test Laboratory (ESTL).

The Hydraulic Test Procedure for Non-instrumented Irradiation Test Rig of Annular Fuel

Energy Technology Data Exchange (ETDEWEB)

Kim, Dae Ho; Lee, Kang Hee; Shin, Chang Hwan; Park, Chan Kook

2008-08-15

This report presents the procedure of pressure drop test, vibration test and endurance test for the non-instrumented rig using the irradiation test in HANARO of advanced PWR annular fuel which were designed and fabricated by KAERI. From the out-pile thermal hydraulic tests, confirm the flow rate at the 200 kPa pressure drop and measure the RMS displacement at this time. And the endurance test is confirmed the wear and the integrity of the non-instrumented rig at the 110% design flow rate. This out-pile test perform the Flow-Induced Vibration and Pressure Drop Experimental Tester(FIVPET) facility. The instruments in FIVPET facility was calibrated in KAERI and the pump and the thermocouple were certified by manufacturer.

27 CFR 4.40 - Label approval and release.

Science.gov (United States)

2010-04-01

..., DEPARTMENT OF THE TREASURY LIQUORS LABELING AND ADVERTISING OF WINE Requirements for Withdrawal of Wine From..., denial, and revocation of certificates of label approval, as well as appeal procedures, see part 13 of...

Characterization of spent fuel approved testing material---ATM-105

Energy Technology Data Exchange (ETDEWEB)

Guenther, R.J.; Blahnik, D.E.; Campbell, T.K.; Jenquin, U.P.; Mendel, J.E.; Thomas, L.E.; Thornhill, C.K.

1991-12-01

The characterization data obtained to data are described for Approved Testing Material 105 (ATM-105), which is spent fuel from Bundles CZ346 and CZ348 of the Cooper Nuclear Power Plant, a boiling-water reactor. This report is one in a series being prepared by the Materials Characterization Center at Pacific Northwest Laboratory (PNL) on spent fuel ATMs. The ATMs are receiving extensive examinations to provide a source of well-characterized spent fuel for testing in the US Department of Energy Office of Civilian Radioactive Waste Management (OCRWM) Program. ATM-105 consists of 88 full-length irradiated fuel rods with rod-average burnups of about 2400 GJ/kgM (28 MWd/kgM) and expected fission gas release of about 1%. Characterization data include (1) descriptions of as-fabricated fuel design, irradiation history, and subsequent storage and handling; (2) isotopic gamma scans; (3) fission gas analyses; (4) ceramography of the fuel and metallography of the cladding; (5) special fuel studies involving analytical transmission electron microscopy (AEM); (6) calculated nuclide inventories and radioactivities in the fuel and cladding; and (7) radiochemical analyses of the fuel and cladding. Additional analyses of the fuel are being conducted and will be included in planned revisions of this report.

75 FR 59105 - Procedures for Transportation Workplace Drug and Alcohol Testing Programs: Federal Drug Testing...

Science.gov (United States)

2010-09-27

... 2105-AE03 Procedures for Transportation Workplace Drug and Alcohol Testing Programs: Federal Drug... the Federal workplace drug testing program but also pointed out that ``* * * the Department of.... Executive Order 12866 and Regulatory Flexibility Act This Interim Final Rule is not significant for purposes...

Update on Nonsurgical Lung Volume Reduction Procedures

Directory of Open Access Journals (Sweden)

J. Alberto Neder

2016-01-01

Full Text Available There has been a surge of interest in endoscopic lung volume reduction (ELVR strategies for advanced COPD. Valve implants, coil implants, biological LVR (BioLVR, bronchial thermal vapour ablation, and airway stents are used to induce lung deflation with the ultimate goal of improving respiratory mechanics and chronic dyspnea. Patients presenting with severe air trapping (e.g., inspiratory capacity/total lung capacity (TLC 225% predicted and thoracic hyperinflation (TLC > 150% predicted have the greatest potential to derive benefit from ELVR procedures. Pre-LVRS or ELVR assessment should ideally include cardiological evaluation, high resolution CT scan, ventilation and perfusion scintigraphy, full pulmonary function tests, and cardiopulmonary exercise testing. ELVR procedures are currently available in selected Canadian research centers as part of ethically approved clinical trials. If a decision is made to offer an ELVR procedure, one-way valves are the first option in the presence of complete lobar exclusion and no significant collateral ventilation. When the fissure is not complete, when collateral ventilation is evident in heterogeneous emphysema or when emphysema is homogeneous, coil implants or BioLVR (in that order are the next logical alternatives.

AP-102/104 Retrieval control system qualification test procedure

International Nuclear Information System (INIS)

RIECK, C.A.

1999-01-01

This Qualification Test Procedure documents the results of the qualification testing that was performed on the Project W-211, ''Initial Tank Retrieval Systems,'' retrieval control system (RCS) for tanks 241-AP-102 and 241-AP-104. The results confirm that the RCS has been programmed correctly and that the two related hardware enclosures have been assembled in accordance with the design documents

7 CFR 983.52 - Failed lots/rework procedure.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Failed lots/rework procedure. 983.52 Section 983.52..., ARIZONA, AND NEW MEXICO Regulations § 983.52 Failed lots/rework procedure. (a) Substandard pistachios... committee may establish, with the Secretary's approval, appropriate rework procedures. (b) Failed lot...

European wind turbine procedure development blade test methods and techniques

Energy Technology Data Exchange (ETDEWEB)

Bulder, B H; Dam, J J.D. van; Delft, D R.V. van [and others

1999-03-01

In this paper the preliminary results obtained by performing the second task of the `European Wind Turbine Testing Procedure Development` project are presented. This project is performed within and with financial support of the Standards, Measurements and Testing programme of the European Commission. (au)

40 CFR 92.123 - Test procedure; general requirements.

Science.gov (United States)

2010-07-01

... the test. Auxiliary fan(s) may be used to maintain engine cooling during operation on the dynamometer... smoke. (1) In the raw exhaust sampling procedure, sample is collected directly from the exhaust stream... of another raw exhaust sample. The fuel flow rate for each throttle setting is measured. (2) For...

40 CFR 86.1527 - Idle test procedure; overview.

Science.gov (United States)

2010-07-01

... from a single exhaust pipe in which exhaust products are homogeneously mixed. The configuration for... additional “Y” pipe be placed in the exhaust system before dilution. [48 FR 52252, Nov. 16, 1983... determine the raw concentration (in percent) of CO in the exhaust flow at idle. The test procedure begins...

Welding procedure specification for arc welding of St 52-3N steel plates with covered electrodes

International Nuclear Information System (INIS)

Cvetkovski, S.; Slavkov, D.; Magdeski, J.

2003-01-01

In this paper the results of approval welding technology for arc welding of plates made of St 52-3N steel are presented. Metal arc welding with covered electrode is used welding process. Test specimens are butt welded in different welding positions P A , P F , P C and P D . Before start welding preliminary welding procedure was prepared. After welding of test specimens non destructive and destructive testing was performed. Obtained results were compared with standard DIN 17100 which concerns to chemical composition and mechanical properties of base material. It was confirmed that in all cases mechanical properties of welded joint are higher than those of base material, so preliminary welding procedure (pWTS) can be accepted as welding procedure specification WPS for metal arc welding of St52-3N steel. (Original)

40 CFR 131.21 - EPA review and approval of water quality standards.

Science.gov (United States)

2010-07-01

... (CONTINUED) WATER PROGRAMS WATER QUALITY STANDARDS Procedures for Review and Revision of Water Quality Standards § 131.21 EPA review and approval of water quality standards. (a) After the State submits its... analysis. (b) The Regional Administrator's approval or disapproval of a State water quality standard shall...

Reconnaissance On Chi-Square Test Procedure For Determining Two Species Association

Science.gov (United States)

Marisa, Hanifa

2008-01-01

Determining the assosiation of two species by using chi-square test has been published. Utility of this procedure to plants species at certain location, shows that the procedure could not find "ecologically" association. Tens sampling units have been made to record some weeds species in Indralaya, South Sumatera. Chi square test; Xt2 = N[|(ad)-(bc)|-(N/2)]2/mnrs (Eq:1) on two species (Cleome sp and Eleusine indica) of the weeds shows positive assosiation; while ecologically in nature, there is no relationship between them. Some alternatives are proposed to this problem; simplified chi-square test steps, make further study to find out ecologically association, or at last, ignore it.

FFTF reactor plant procedures plan

International Nuclear Information System (INIS)

1972-01-01

The document presented defines the plan to be used to coordinate the preparation, review, approval, and issuance of the operating procedure documents required to ensure safe and efficient operation of FFTF

Procedure guideline for radioiodine test (version 3)

International Nuclear Information System (INIS)

Dietlein, M.; Schicha, H.; Eschner, W.; Deutsche Gesellschaft fuer Medizinische Physik; Koeln Univ.; Lassmann, M.; Deutsche Gesellschaft fuer Medizinische Physik; Wuerzburg Univ.; Leisner, B.; Allgemeines Krankenhaus St. Georg, Hamburg; Reiners, C.; Wuerzburg Univ.

2007-01-01

The version 3 of the procedure guideline for radioiodine test is an update of the guideline previously published in 2003. The procedure guideline discusses the pros and cons of a single measurement or of repeated measurements of the iodine-131 uptake and their optimal timing. Different formulas are described when one, two or three values of the radioiodine kinetic are available. The probe with a sodium-iodine crystal, alternatively or additionally the gamma camera using the ROI-technique are instrumentations for the measurement of iodine-131 uptake. A possible source of error is an inappropriate measurement (sonography) of the target volume. The patients' preparation includes the withdrawal of antithyroid drugs 2-3 days before radioiodine administration. The patient has to avoid iodine-containing medication and the possibility of additives of iodine in vitamin- and electrolyte-supplementation has to be considered. (orig.)

Development test procedure High Pressure Water Jet System

International Nuclear Information System (INIS)

Crystal, J.B.

1995-01-01

Development testing will be performed on the water jet cleaning fixture to determine the most effective arrangement of water jet nozzles to remove contamination from the surfaces of canisters and other debris. The following debris may be stained with dye to simulate surface contaminates: Mark O, Mark I, and Mark II Fuel Storage Canisters (both stainless steel and aluminum), pipe of various size, (steel, stainless, carbon steel and aluminum). Carbon steel and stainless steel plate, channel, angle, I-beam and other surfaces, specifically based on the Scientific Ecology Group (SEG) inventory and observations of debris within the basin. Test procedure for developmental testing of High Pressure Water Jet System

A testing procedure for wind turbine generators based on the power grid statistical model

DEFF Research Database (Denmark)

Farajzadehbibalan, Saber; Ramezani, Mohammad Hossein; Nielsen, Peter

2017-01-01

In this study, a comprehensive test procedure is developed to test wind turbine generators with a hardware-in-loop setup. The procedure employs the statistical model of the power grid considering the restrictions of the test facility and system dynamics. Given the model in the latent space...

Quality assurance of radiopharmaceuticals - specifications and test procedures

International Nuclear Information System (INIS)

Baldas, J.; Bonnyman, J.; Colmanet, S.F.; Ivanov, Z.; Lauder, R.A.

1990-10-01

The authors report on a Radiopharmaceutical Quality Assurance Test Programme carried out by the Australian Radiation Laboratory in which radiopharmaceuticals used in nuclear medicine in Australia are tested for compliance with specifications. Where the radiopharmaceutical is the subject of a monograph in the British Pharmacopoeia or the European Pharmacopoeia, then the specifications given in the Pharmacopoeia are adopted. In other cases the specifications given have been adopted by this Laboratory and have no legal status. In some cases test procedures described have been taken from various Pharmacopoeias or methods published in the literature. In other cases test methods described have been developed at this Laboratory. It should be noted that, unless stated otherwise, specifications listed apply at all times up until product expire

27 CFR 7.31 - Label approval and release.

Science.gov (United States)

2010-04-01

..., DEPARTMENT OF THE TREASURY LIQUORS LABELING AND ADVERTISING OF MALT BEVERAGES Requirements for Withdrawal of... approval, as well as appeal procedures, see part 13 of this chapter. [T.D. ATF-66, 45 FR 40552, June 13...

27 CFR 7.41 - Certificates of label approval.

Science.gov (United States)

2010-04-01

..., DEPARTMENT OF THE TREASURY LIQUORS LABELING AND ADVERTISING OF MALT BEVERAGES Requirements for Approval of..., as well as appeal procedures, see part 13 of this chapter. [T.D. ATF-406, 64 FR 2129, Jan. 13, 1999...

[Procedure of seed quality testing and seed grading standard of Prunus humilis].

Science.gov (United States)

Wen, Hao; Ren, Guang-Xi; Gao, Ya; Luo, Jun; Liu, Chun-Sheng; Li, Wei-Dong

2014-11-01

So far there exists no corresponding quality test procedures and grading standards for the seed of Prunus humilis, which is one of the important source of base of semen pruni. Therefor we set up test procedures that are adapt to characteristics of the P. humilis seed through the study of the test of sampling, seed purity, thousand-grain weight, seed moisture, seed viability and germination percentage. 50 cases of seed specimens of P. humilis tested. The related data were analyzed by cluster analysis. Through this research, the seed quality test procedure was developed, and the seed quality grading standard was formulated. The seed quality of each grade should meet the following requirements: for first grade seeds, germination percentage ≥ 68%, thousand-grain weight 383 g, purity ≥ 93%, seed moisture ≤ 5%; for second grade seeds, germination percentage ≥ 26%, thousand-grain weight ≥ 266 g, purity ≥ 73%, seed moisture ≤9%; for third grade seeds, germination percentage ≥ 10%, purity ≥ 50%, thousand-grain weight ≥ 08 g, seed moisture ≤ 13%.

Acceptance test procedure for a portable, self-contained nitrogen supply

International Nuclear Information System (INIS)

Kostelnik, A.J.

1994-01-01

This Acceptance Test Procedure (ATP) will document compliance with the requirements of WHC-S-0249 Rev. 1 and ECN 606112. The equipment being tested is a Portable, Self-Contained Nitrogen Supply. The unit was purchased as a Design and Fabrication procurement activity. The Functional Test was written by the Seller and is contained in Appendix A. The Functional test will be performed by the Seller with representatives of the Westinghouse Hanford Company performing inspection and witnessing the functional test at the Seller's location

Approval Procedure for Technical Specifications for Procurement by Quotation and Tender

International Nuclear Information System (INIS)

Shaharum Ramli; Izhar Abu Hussin; Ying, K.K.

2015-01-01

Technical specifications for procurement requires the approval of the Jawatankuasa Penyemak Spesifikasi Teknikal Tender/ Sebutharga Agensi Nuklear Malaysia. This paper provides guidance for those who have to prepare a technical specification. In addition, the technical specification online library is introduced to facilitate them to re-use old technical specifications for new procurements or to make those the bases for drafting new specifications. (author)

PUREX (SAMCONS) uninterruptible power supply (UPS) acceptance test procedure

International Nuclear Information System (INIS)

Blackaby, W.B.

1997-01-01

This Acceptance Test Procedure for the PUREX Surveillance and Monitoring and Control System (SAMCONS) Uninterruptible Power Supply (UPS) provides for testing and verifying the proper operation of the control panel alarms and trouble functions, the 6roper functioning of the AC inverter, ability of the battery supply to maintain the SAMCONS load for a minimum of two hours , and proper interaction with the SAMCONS Video graphic displays for alarm displays

40 CFR Appendix A to Subpart T of... - Test of Solvent Cleaning Procedures

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Test of Solvent Cleaning Procedures A... CATEGORIES National Emission Standards for Halogenated Solvent Cleaning Pt. 63, Subpt. T, App. A Appendix A to Subpart T of Part 63—Test of Solvent Cleaning Procedures General Questions ___ 1. What is the...

16 CFR 1610.33 - Test procedures for textile fabrics and film.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Test procedures for textile fabrics and film... for textile fabrics and film. (a)(1) All textile fabrics (except those with a nitro-cellulose fiber... under the procedures outlined in part 1611, Standard for the Flammability of Vinyl Plastic Film, and if...

Procedure for getting safety classed concrete structures approved by Finnish Radiation and Nuclear Safety Authority

International Nuclear Information System (INIS)

Halme, Ville-Juhani

2015-01-01

Posiva is preparing geological final disposal in the Finnish bedrock in Olkiluoto, Eurajoki. The final disposal facility includes encapsulation plant and underground repository. Most of the main civil structures are concrete structures. STUK is the supervising authority in civil structures. The National Building Code of Finland and STUK's Regulatory Guide on nuclear safety (YVL) are the most important instructions when constructing concrete structures into nuclear installation. Posiva has classified concrete structures in two classes according STUK's YVL-guidance: EYT (non-nuclear) and Safety Class 3 (SC 3, nuclear safety significance). When building SC 3 concrete structures, specific protocol must be followed. Protocol includes planned routines for design, construction, supervision, quality control (QC) and quality assurance (QA) activities. Documents relating concrete structures must be approved by Posiva and STUK before construction work. After structures have been designed and actual building is ongoing, there are two main steps. Before concreting, readiness inspection for concreting must be arranged. Readiness inspection will be arranged according to a specific plan and the date must be informed to STUK. After establishing readiness for concreting, casting work can begin. Once concrete structures are done, inspected and approved, final documentation according to a quality control plan will be reviewed by Posiva. After Posiva's approval, final documentation will be sent for STUK's approval. In the end STUK will give the permission for commissioning of the concrete structures after approved commissioning inspection. The document is made up of an abstract and a poster

Study on service test procedure for SMES systems

Energy Technology Data Exchange (ETDEWEB)

Ren, L., E-mail: rl8868@126.co [R and D Center of Applied Superconductivity, Huazhong University of Science and Technology, Wuhan 430074 (China); Tang, Y.; Li, J.; Shi, J. [R and D Center of Applied Superconductivity, Huazhong University of Science and Technology, Wuhan 430074 (China); Hu, Y. [State Grid Electric Power Research Institute, Wuhan 430074 (China); Guo, F.; Chen, L.; Cheng, S. [R and D Center of Applied Superconductivity, Huazhong University of Science and Technology, Wuhan 430074 (China)

2009-10-15

Some superconducting magnetic energy storage (SMES) systems have been developed successfully, and the function of them was verified by experiment. Considering the impact on the system security and stability when they are connected to the power system, it is important to build a standard test procedure and propose the main experimental contents for some representative superconducting devices. Based on the experimental results of a 35 kJ/7 kW conduction-cooled high-T{sub c} SMES system, which was developed by Huazhong University of Science and Technology, the test items and methods for a conduction-cooled high-T{sub c} SMES system are studied. For performance evaluation of this high-T{sub c} SMES, three superconducting magnet performance tests, power conditioning characteristic test and dynamic experiment in a simulated power system were fulfilled.

Study on service test procedure for SMES systems

International Nuclear Information System (INIS)

Ren, L.; Tang, Y.; Li, J.; Shi, J.; Hu, Y.; Guo, F.; Chen, L.; Cheng, S.

2009-01-01

Some superconducting magnetic energy storage (SMES) systems have been developed successfully, and the function of them was verified by experiment. Considering the impact on the system security and stability when they are connected to the power system, it is important to build a standard test procedure and propose the main experimental contents for some representative superconducting devices. Based on the experimental results of a 35 kJ/7 kW conduction-cooled high-T c SMES system, which was developed by Huazhong University of Science and Technology, the test items and methods for a conduction-cooled high-T c SMES system are studied. For performance evaluation of this high-T c SMES, three superconducting magnet performance tests, power conditioning characteristic test and dynamic experiment in a simulated power system were fulfilled.

Knowledge and use of unauthorized HIV self-test kits among men who have sex with men in Spain, following approval of an over-the-counter self-test in the U.S: a cross-sectional study.

Science.gov (United States)

Koutentakis, Konstantinos; Rosales-Statkus, María Elena; Hoyos, Juan; Fernández-Balbuena, Sonia; Ruiz, Mónica; Agustí, Cristina; de la Fuente, Luis; Belza, María José

2016-07-08

Shortly after the approval of an over-the-counter HIV self-test in the US, we conducted a study to estimate the proportion of men who have sex with men (MSM) in Spain who knew that unauthorized HIV self-tests could be purchased online, and the proportion that had already used these tests, as well as their socio-demographic and behavioural correlates. Between September 2012 and February 2013, MSM users of gay dating websites were invited to complete an online questionnaire. We calculated estimates of the knowledge and use of unauthorized HIV self-testing and assessed the associated factors by rare event logit regression models. Among 8620 participants, 4.2 % (95 % CI:3.8-4.6) knew they could buy an unauthorized HIV self-test kit online, and 12.7 % (95 % CI:12.0-13.4) thought that such a test might exist, although they had never seen one. Only 0.7 % (95 % CI:0.5-0.9) had ever self-tested. In the multivariable analysis, knowledge of online availability of self-tests was associated with being a non-Latin American foreigner, having at least two previous HIV tests, intending to test for HIV in the next year, and knowing about U.S. approval of self-testing. Ever-use of HIV self-testing was associated with being over 34 years of age, living outside Spain during the last 12 months, and knowing about U.S. approval of self-testing. Both knowledge and use of unauthorized HIV self-testing among MSM in Spain was very low among HIV negative or untested MSM in Spain. The recent approval in the United Kingdom and France might increase the number of MSM seeking such testing and possibly using unauthorized test kits not meeting quality standards.

48 CFR 432.003 - Simplified acquisition procedures financing.

Science.gov (United States)

2010-10-01

... procedures financing. 432.003 Section 432.003 Federal Acquisition Regulations System DEPARTMENT OF AGRICULTURE GENERAL CONTRACTING REQUIREMENTS CONTRACT FINANCING 432.003 Simplified acquisition procedures financing. (a) The chief of the contracting office may approve contract financing on a contract to be...

Test and evaluation procedures for Sandia's Teraflops Operating System (TOS) on Janus.

Energy Technology Data Exchange (ETDEWEB)

Barnette, Daniel Wayne

2005-10-01

This report describes the test and evaluation methods by which the Teraflops Operating System, or TOS, that resides on Sandia's massively-parallel computer Janus is verified for production release. Also discussed are methods used to build TOS before testing and evaluating, miscellaneous utility scripts, a sample test plan, and a proposed post-test method for quickly examining the large number of test results. The purpose of the report is threefold: (1) to provide a guide to T&E procedures, (2) to aid and guide others who will run T&E procedures on the new ASCI Red Storm machine, and (3) to document some of the history of evaluation and testing of TOS. This report is not intended to serve as an exhaustive manual for testers to conduct T&E procedures.

Acceptance Test Procedure for New Pumping and Instrumentation Control Skid L

International Nuclear Information System (INIS)

KOCH, M.R.

1999-01-01

This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping and Instrumentation Control (PIC) skid designed as ''L''. The ATP will be performed after the construction of the PIC skid in the shop

Acceptance Test Procedure for New Pumping and Instrumentation Control Skid N

International Nuclear Information System (INIS)

KOCH, M.R.

1999-01-01

This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping and Instrumentation Control (PIC) skid designed as ''N''. The ATP will be performed after the construction of the PIC skid in the shop

Phased Startup Initiative Phase 3 and 4 Test Procedure (OCRWM)

International Nuclear Information System (INIS)

PAJUNEN, A.L.

2000-01-01

The purpose of this test procedure is to safely operate the Fuel Retrieval System (FRS) and Integrated Water Treatment System (IWTS) with specific fuel canisters, and show that canisters containing fuel can be retrieved from the canister queue, decapped in the Canister Decapper, and loaded into the Primary Clean Machine (PCM) for fuel cleaning; and that fuel can be sorted on the Process Table, then loaded back into fuel canisters and relocated in basin storage. An option is included to load selected elements into multi-canister overpack (MCO) Fuel Baskets. Additional Data are collected during this test, beyond that collected during production operations. These data support qualifying the cleaning performance of the PCM, assessing the quantity of scrap generated during the cleaning, and evaluating the impact of fuel retrieval operations on the Basin water quality. The additional data collected primarily consist of weighing fuel and scrap at selected points in the operation, as well as photographing fuel and scrap as it is processed. The time to perform operations is also monitored for comparison with design predictions. Water quality data are collected to establish a baseline to predict the effectiveness of equipment design for control of contamination and visibility during production operation. The scope of this test procedure is to validate the operation of FRS and IWTS components as a complete system. Fuel canisters shall be processed in accordance with this test procedure such that fuel inspection results are clearly attributed to a particular set of PCM operating parameters. The Phase 3 test sequence processes a minimum of six canisters. Twenty-four contingency canisters have been identified, and will be processed if additional performance data are required. The Phase 4 test sequence processes a minimum of 29 specific canisters. Twenty-nine contingency canisters have been identified for Phase 4 activities and will be processed to complete process validation, if

Acceptance Test Procedure for New Pumping Instrumentation and Control Skid ''P''

International Nuclear Information System (INIS)

KOCH, M.R.

2000-01-01

This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''P''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

Acceptance Test Procedure for New Pumping Instrumentation and Control Skid W

International Nuclear Information System (INIS)

KOCH, M.R.

2000-01-01

This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''W''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

Acceptance Test Procedure for New Pumping Instrumentation and Control Skid V

International Nuclear Information System (INIS)

KOCH, M.R.

2000-01-01

This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control. (PIC) skid designed as ''V''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

Acceptance Test Procedure for New Pumping Instrumentation and Control Skid ''V''

International Nuclear Information System (INIS)

KOCH, M.R.

2000-01-01

This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designated as ''V''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

Acceptance Test Procedure for New Pumping Instrumentation and Control Skid ''Q''

International Nuclear Information System (INIS)

KOCH, M.R.

2000-01-01

This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''Q''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

Acceptance Test Procedure for New Pumping Instrumentation and Control Skid ''T''

International Nuclear Information System (INIS)

KOCH, M.R.

2000-01-01

This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designated as ''T''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

Acceptance Test Procedure for New Pumping Instrumentation and Control Skid T

International Nuclear Information System (INIS)

KOCH, M.R.

2000-01-01

This Acceptance Test Procedure (ATP) provides for the inspection and testing Of the new Pumping Instrumentation and Control (PIC) skid designed as ''T''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

Acceptance Test Procedure for New Pumping Instrumentation and Control Skid R

International Nuclear Information System (INIS)

KOCH, M.R.

2000-01-01

This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''R''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

Acceptance Test Procedure for New Pumping Instrumentation and Control Skid ''U''

International Nuclear Information System (INIS)

KOCH, M.R.

2000-01-01

This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''U''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

CENRTC Project number-sign 2F3EOA, OCB A-376, acceptance test procedure

International Nuclear Information System (INIS)

Akerson, A.W.

1995-01-01

This test procedure provides the steps necessary to verify correct functional operation of controls, annunciators, alarms, protective relays and related systems impacted by CENRTC number-sign 2F3E0A, Microwave Transfer Trip Project, modification work performed under work package 6B-93-00041/M. This procedure separates three tests into separate sections: energization of A-376 duplex panel and circuits; SCADA tests; and A-376 local trip tests

The minimal ice water caloric test compared with established vestibular caloric test procedures.

Science.gov (United States)

Schmäl, Frank; Lübben, Björn; Weiberg, Kerstin; Stoll, Wolfgang

2005-01-01

Caloric testing of the vestibular labyrinth is usually performed by classical caloric test procedures (CCTP) using water warmed to 30 degrees C and 44 degrees C. Ice water irrigation (4 degrees C) is usually not performed, although it might be useful as a bedside test. To verify the validity of the Minimal Ice Water Caloric Test (MIWCT), comparative video-oculographic investigations were performed in 22 healthy subjects using ice water (0.5 ml, 1.0 ml, 2 ml), CCTP, and cold air (27 degrees C). Frequency, amplitude, slow phase velocity (SPV), the onset, and the duration of nystagmus were documented. After addition of three ice cubes, the temperature of conventional tap water (16 degrees C) fell within 13 min to 4 degrees C. In pessimum position the subjects demonstrated no nystagmus response. Compared to CCTP, MIWCT was associated with a significantly later onset of nystagmus and a significant prolongation of the nystagmus reaction. In contrast to air stimulation (27 degrees C), a significant Spearman's correlation was noted between MIWCT (1 and 2 ml) and established CCTP in respect of essential nystagmus parameters (frequency, amplitude and SPV). Furthermore, MIWCT (0.5 and 1 ml) showed a higher sensitivity and specificity with regard to the detection of canal paresis based on Jongkees' formula compared to stimulation with air 27 degrees C. Thus, MIWCT appears to be a suitable procedure for bedside investigation of vestibular function outside the vestibular laboratory, e.g. in a hospital ward, where bedridden patients with vertigo occasionally require vestibular testing.

Memory and other properties of multiple test procedures generated by entangled graphs.

Science.gov (United States)

Maurer, Willi; Bretz, Frank

2013-05-10

Methods for addressing multiplicity in clinical trials have attracted much attention during the past 20 years. They include the investigation of new classes of multiple test procedures, such as fixed sequence, fallback and gatekeeping procedures. More recently, sequentially rejective graphical test procedures have been introduced to construct and visualize complex multiple test strategies. These methods propagate the local significance level of a rejected null hypothesis to not-yet rejected hypotheses. In the graph defining the test procedure, hypotheses together with their local significance levels are represented by weighted vertices and the propagation rule by weighted directed edges. An algorithm provides the rules for updating the local significance levels and the transition weights after rejecting an individual hypothesis. These graphical procedures have no memory in the sense that the origin of the propagated significance level is ignored in subsequent iterations. However, in some clinical trial applications, memory is desirable to reflect the underlying dependence structure of the study objectives. In such cases, it would allow the further propagation of significance levels to be dependent on their origin and thus reflect the grouped parent-descendant structures of the hypotheses. We will give examples of such situations and show how to induce memory and other properties by convex combination of several individual graphs. The resulting entangled graphs provide an intuitive way to represent the underlying relative importance relationships between the hypotheses, are as easy to perform as the original individual graphs, remain sequentially rejective and control the familywise error rate in the strong sense. Copyright © 2012 John Wiley & Sons, Ltd.

16 CFR 1501.4 - Size requirements and test procedure.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Size requirements and test procedure. 1501.4 Section 1501.4 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL HAZARDOUS SUBSTANCES ACT.... The metric approximations are included only for convenience.) (b)(1) Place the article, without...

Test procedures and instructions for Hanford tank waste supernatant cesium removal

Energy Technology Data Exchange (ETDEWEB)

Hendrickson, D.W., Westinghouse Hanford

1996-05-31

This document provides specific test procedures and instructions to implement the test plan for the preparation and conduct of a cesium removal test using Hanford Double-Shell Slurry Feed supernatant liquor from tank 251-AW-101 in a bench-scale column.Cesium sorbents to be tested include resorcinol-formaldehyde resin and crystalline silicotitanate. The test plan for which this provides instructions is WHC-SD-RE-TP-022, Hanford Tank Waste Supernatant Cesium Removal Test Plan.

A Bayesian decision procedure for testing multiple hypotheses in DNA microarray experiments.

Science.gov (United States)

Gómez-Villegas, Miguel A; Salazar, Isabel; Sanz, Luis

2014-02-01

DNA microarray experiments require the use of multiple hypothesis testing procedures because thousands of hypotheses are simultaneously tested. We deal with this problem from a Bayesian decision theory perspective. We propose a decision criterion based on an estimation of the number of false null hypotheses (FNH), taking as an error measure the proportion of the posterior expected number of false positives with respect to the estimated number of true null hypotheses. The methodology is applied to a Gaussian model when testing bilateral hypotheses. The procedure is illustrated with both simulated and real data examples and the results are compared to those obtained by the Bayes rule when an additive loss function is considered for each joint action and the generalized loss 0-1 function for each individual action. Our procedure significantly reduced the percentage of false negatives whereas the percentage of false positives remains at an acceptable level.

Development of a radionuclide short-test for the evaluation of engine oils in respect to cam- and cylinder linear wear by using OM 616 Kombi-Test conditions

International Nuclear Information System (INIS)

Volz, J.; Lausch, W.

1980-05-01

A survey is given on the studies performed since 1973 on the development of radionuclide short-test procedure, based on the test procedure of the OM 616 Kombi-Test, for the evaluation of engine oils in respect to cam- and cylinder liner wear (deuteron activated Co-56). Out of the results of these studies on experimental short test procedure has been elaborated to evaluate cylinder liner wear. With this experimental procedure some round robin testing has been carried out by three laboratories using a well-known reference oil and two test oils. The results of this round robin test led to further improvements in the test procedure. This improved test procedure has become a suitable screening-test for the development of engine oils in respect to cylinder liner wear. It never can replace the OM 616-Kombi-Test as a whole, but it will complete it. The radionuclide short test gets results quicker and at lower costs than the Kombi-Test, discriminates between hot test and cold-warm test results, and gives results even with correlation to the Kombi-Test by comparison to an approved reference oil. For such screening work, the repeatability of the test is also sufficient. (orig./HP) [de

78 FR 5430 - Extension of Approval Period for Certain Tests Used in the National Reporting System for Adult...

Science.gov (United States)

2013-01-25

... DEPARTMENT OF EDUCATION Extension of Approval Period for Certain Tests Used in the National Reporting System for Adult Education AGENCY: Office of Vocational and Adult Education, Department of... National Reporting System for Adult Education (NRS regulations) (73 FR 2306). The NRS regulations...

78 FR 23884 - Seed Testing Service Program; Request for an Extension of and Revision to a Currently Approved...

Science.gov (United States)

2013-04-23

... DEPARTMENT OF AGRICULTURE Agricultural Marketing Service [Doc. No. AMS-LS-13-0007] Seed Testing... AGENCY: Agricultural Marketing Service, USDA. ACTION: Request for comments. SUMMARY: In accordance with... Marketing Service's (AMS) intention to request approval from the Office of Management and Budget (OMB), for...

28 CFR 58.26 - Procedures for inclusion on the approved provider list.

Science.gov (United States)

2010-07-01

... provider list. (a) As used in this section the term “provider” means a provider of a personal financial... of a Personal Financial Management Course” (application), including all appendices, and submit it at... directors; and a merger or consolidation with another entity; (2) The provider shall request approval by...

ENRAF Series 854 Advanced Technology Gauge (ATG) Acceptance Test Procedure

International Nuclear Information System (INIS)

HUBER, J.H.

1999-01-01

This procedure provides acceptance testing for Enraf Series 854 level gauges used to monitor levels in Hanford Waste Storage Tanks. The test will verify that the gauge functions according to the manufacturer's instructions and specifications and is properly setup prior to being delivered to the tank farm area. This ATP does not set up the gauge for any specific tank, but is generalized to permit testing the gauge prior to installation package preparation

75 FR 42611 - Energy Conservation Program for Consumer Products: Test Procedure for Microwave Ovens

Science.gov (United States)

2010-07-22

... for Microwave Ovens AGENCY: Office of Energy Efficiency and Renewable Energy, Department of Energy... current active mode provisions in its test procedure for microwave ovens do not produce accurate and... concerns with the DOE microwave oven cooking efficiency test procedure. Elsewhere in today's Federal...

Project W-314 performance mock-up test procedure

International Nuclear Information System (INIS)

CARRATT, R.T.

1999-01-01

The purpose of this Procedure is to assist construction in the pre-operational fabrication and testing of the pit leak detection system and the low point drain assembly by: (1) Control system testing of the pit leak detection system will be accomplished by actuating control switches and verifying that the control signal is initiated, liquid testing and overall operational requirements stated in HNF-SD-W314-PDS-003, ''Project Development Specification for Pit Leak Detection''. (2) Testing of the low point floor drain assembly by opening and closing the drain to and from the ''retracted'' and ''sealed'' positions. Successful operation of this drain will be to verify that the seal does not leak on the ''sealed'' position, the assembly holds liquid until the leak detector actuates and the assembly will operate from on top of the mock-up cover block

Procedure for vibration test of the fuel rod supported by spacer grids

International Nuclear Information System (INIS)

Choi, Myoung Hwan; Kang, Heung Seok; Yoon, Kyung Ho; Kim, Hyung Kyu; Song, Kee Nam

2002-07-01

One of the methods that are used to compare and verify the supporting performance of the spacer grids developed is the vibration characteristic test. In this report there are two aims. One is of the understand of the experimental method and procedure performing the modal testing using I-DEAS TDAS module. The other is the investigation of the vibration behaviors of a dummy fuel rod supported by 8 optimized H type spacer grids. This report describes the method and procedure of modal testing to obtain the vibration characteristics such as amplitudes, natural frequencies and mode shapes of the fuel rod using a shaker, a non-contact gap sensor and an accelerometer. This report provides a test procedure in detail so that anyone can be easily understood and use the I-DEAS TDAS program. The I-DEAS TDAS program related to the modal testing has several tasks including the Modal analysis, Signal Processing et al.. This report includes model preparation to prepare the geometrical model, Signal Processing (Sine/Standard measurement) to acquire the signal, Modal analysis to obtain the frequencies and mode shapes, Correlation to analyze the relation between the test and FE analysis and Post Processing tasks. In addition, this report contains the actual test and analysis data of a dummy fuel rod in length 3847mm supported by 8 optimized H type spacer grids

75 FR 42612 - Energy Conservation Program for Consumer Products: Test Procedure for Microwave Ovens

Science.gov (United States)

2010-07-22

... Conservation Program for Consumer Products: Test Procedure for Microwave Ovens AGENCY: Office of Energy... (NOPR) in which DOE proposed test procedures for microwave ovens under the Energy Policy and Conservation Act (EPCA) to measure standby mode and off mode power use by microwave ovens. To address issues...

40 CFR 1051.501 - What procedures must I use to test my vehicles or engines?

Science.gov (United States)

2010-07-01

... vehicles or engines? 1051.501 Section 1051.501 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM RECREATIONAL ENGINES AND VEHICLES Test Procedures § 1051.501 What procedures must I use to test my vehicles or engines? This section describes test...

21 CFR 314.530 - Withdrawal procedures.

Science.gov (United States)

2010-04-01

... Serious or Life-Threatening Illnesses § 314.530 Withdrawal procedures. (a) For new drugs approved under... benefit; (2) The applicant fails to perform the required postmarketing study with due diligence; (3) Use...

42 CFR 447.256 - Procedures for CMS action on assurances and State plan amendments.

Science.gov (United States)

2010-10-01

... 42 Public Health 4 2010-10-01 2010-10-01 false Procedures for CMS action on assurances and State... for Inpatient Hospital and Long-Term Care Facility Services Payment Rates § 447.256 Procedures for CMS action on assurances and State plan amendments. (a) Criteria for approval. (1) CMS approval action on...

CENRTC Project number-sign 2F3EOA, OCB A-386, acceptance test procedure

International Nuclear Information System (INIS)

Akerson, A.W.

1995-01-01

This test procedure provides the steps necessary to verify correct functional operation of controls, annunciators, alarms, protective relays and related systems impacted by CENRTC number-sign 2F3EOA, Microwave Transfer Trip Project, modification work performed under work package 6B-93-00043/M (CENRTC 2F3EOA MWTT OCB A-386 PACKAGE). This procedure separates four tests into separate sections: Energization of A-386 Duplex Panel and Circuits; Local RFL 6750 function tests and start-up; SCADA tests; and A-386 local trip tests

Procedure on the Impact Characteristic Test for the One-sided and Thru-grid Spacer Grid

International Nuclear Information System (INIS)

Yoon, Kyung Ho; Kim, Jae Yong; Lee, Kang Hee; Song, Kee Nam

2006-09-01

In order to perform the one-sided and the through-grid impact tests for a new developed spacer grid, the drop type impact test machines were established. The dynamic impact test is to get some basic data for accident analysis such as impact strength, stiffness, and coefficient of the restitution. Furthermore, these developed test methods and procedures will be qualified standard for increasing the reliability of the test results. Chapter 2 provides an introduction to the test facilities and instrumentations. Chapter 3 describes on how spacer grid and the single span fuel assembly specimen will be prepared. In addition to this, how to set up these testing machines. Chapter 4 illustrates detail test procedure on how to acquire impact signal of the two kinds of the specimen. Chapter 5 deals with signal processing and analysis for the test data. Finally, chapter 6 summarise the overall test procedure and the test method

SRS reactor stack plume marking tests

International Nuclear Information System (INIS)

Petry, S.F.

1992-03-01

Tests performed in 105-K in 1987 and 1988 demonstrated that the stack plume can successfully be made visible (i.e., marked) by introducing smoke into the stack breech. The ultimate objective of these tests is to provide a means during an emergency evacuation so that an evacuee can readily identify the stack plume and evacuate in the opposite direction, thus minimizing the potential of severe radiation exposure. The EPA has also requested DOE to arrange for more tests to settle a technical question involving the correct calculation of stack downwash. New test canisters were received in 1988 designed to produce more smoke per unit time; however, these canisters have not been evaluated, because normal ventilation conditions have not been reestablished in K Area. Meanwhile, both the authorization and procedure to conduct the tests have expired. The tests can be performed during normal reactor operation. It is recommended that appropriate authorization and procedure approval be obtained to resume testing after K Area restart

76 FR 12825 - Energy Conservation Program for Consumer Products: Test Procedure for Microwave Ovens

Science.gov (United States)

2011-03-09

... Conservation Program for Consumer Products: Test Procedure for Microwave Ovens AGENCY: Office of Energy.... Department of Energy (DOE) is amending its test procedures for microwave ovens under the Energy Policy and Conservation Act (EPCA) to provide for the measurement of standby mode and off mode power use by microwave...

Preschooler test or procedure preparation

Science.gov (United States)

... your child during and after the procedure with books, songs, counting, deep breathing, or blowing bubbles. PLAY ... can be present during the procedure. Ask if anesthesia can be used to reduce your child's discomfort. ...

Interdisciplinary Development of an Improved Emergency Department Procedural Work Surface Through Iterative Design and Use Testing in Simulated and Clinical Environments.

Science.gov (United States)

Zhang, Xiao C; Bermudez, Ana M; Reddy, Pranav M; Sarpatwari, Ravi R; Chheng, Darin B; Mezoian, Taylor J; Schwartz, Victoria R; Simmons, Quinneil J; Jay, Gregory D; Kobayashi, Leo

2017-03-01

surface and just-in-time training on its use when performing bedside procedures. Subjects completed the validated 10-point System Usability Scale postshift for the surface that they had used. The study protocol was approved by the institutional review board. Multiple prototypes and recursive design revisions resulted in a fully functional, portable, and durable bedside procedural surface that featured a stainless steel tray and intuitive hook-and-lock mechanisms for attachment to ED stretcher bed rails. Forty-two control and 40 experimental group subjects participated and completed questionnaires. The median System Usability Scale score (out of 100; higher scores associated with better usability) was 72.5 (interquartile range [IQR] 51.3 to 86.3) for the Mayo stand; the experimental surface was scored at 93.8 (IQR 84.4 to 97.5 for a difference in medians of 17.5 (95% confidence interval 10 to 27.5). Subjects reported several usability challenges with the Mayo stand; the experimental surface was reviewed as easy to use, simple, and functional. In accordance with experimental live environment deployment, questionnaire responses, and end-user suggestions, the project team finalized the design specification for the experimental procedural surface for open dissemination. An iterative, interdisciplinary approach was used to generate, evaluate, revise, and finalize the design specification for a new procedural surface that met all core end-user requirements. The final surface design was evaluated favorably on a validated usability tool against Mayo stands when use tested in simulated and live clinical settings. Copyright © 2016 American College of Emergency Physicians. Published by Elsevier Inc. All rights reserved.

Quality assurance test of a real time radiography system

International Nuclear Information System (INIS)

Yadav, R.K.; Rama, R.; Sharma, A.; Kannan, R.

2005-01-01

Any radiation generating equipment can be used and marketed in India only after obtaining specific type approval certificate from the Competent Authority i.e. Chairman, Atomic Energy Regulatory Board (AERB), Mumbai. Recently AERB has enforced a directive that the Industrial X-ray machines should also be permitted to use only after getting NOC or type approval. Type approval is granted based upon the satisfactory QA test report of the radiation generating equipment. X-ray machines with Real Time Radiography (RTR) facility are used in industrial radiography for faster inspection of equipment's and products online. A standard test protocol was developed for QA tests of a real time radiography system. This will be helpful for evaluation of an industrial X-ray machine. Also above procedure can be used to check a RTR system each day or a system-qualification can be done when the image quality diminishes as recommended by American Society of Testing Material (ASTM). Various tests carried out on a constant potential 450 kV, 10 mA industrial X-ray machine having real time radiography facility to monitor the products online, is described in this paper. (author)

Retrofit and verification test of a 30-cm ion thruster

Science.gov (United States)

Dulgeroff, C. R.; Poeschel, R. L.

1980-01-01

Twenty modifications were found to be necessary and were approved by design review. These design modifications were incorporated in the thruster documents (drawings and procedures) to define the J series thruster. Sixteen of the design revisions were implemented in a 900 series thruster by retrofit modification. A standardized set of test procedures was formulated, and the retrofit J series thruster design was verified by test. Some difficulty was observed with the modification to the ion optics assembly, but the overall effect of the design modification satisfies the design objectives. The thruster was tested over a wide range of operating parameters to demonstrate its capabilities.

A system for personnel qualification of non-destructive testing procedures from testing and and qualification system in Sweden

International Nuclear Information System (INIS)

Kuna, M.; Kubis, S.; Plasek, J.

1999-01-01

The method for qualification of non-destructive testing personnel carrying out inspections by means of ultrasonic and eddy-current tests to inspect cladding in BWR reactor pressure vessel and core shroud lid. Development of procedures tests with real artificial cracks, blind tests. Evaluation of results by the Swedish Qualification Commission. Performance of the tests at Oskarshamn-1

Specifications and test procedures for airline-type supplied-air suits

International Nuclear Information System (INIS)

Revoir, W.H.; Pritchard, J.A.; Davis, T.O.; Richards, C.P.; Wheat, L.D.

1975-05-01

Procedures and requirements have been established to permit airline-type supplied-air suits needed by contractors of the Energy Research and Development Administration to be tested for performance by the Respirator Research and Development Section, Industrial Hygiene Group, of the Los Alamos Scientific Laboratory, and to have the adequacy of the performance of these devices evaluated by the Los Alamos Scientific Laboratory Respirator Advisory Committee. Test equipment, test methods, and performance criteria for airline-type supplied-air suits are prescribed. (U.S.)

Problems of the current law concerning official plan approval

International Nuclear Information System (INIS)

Bluemel, W.

1986-01-01

The booklet presents lectures held in October 1985 at the Speyer University for Administration Science, on the subject of the law concerning official plan approval. The lectures have been selected for their common interest in the requirements of nature conservation and landscape protection. These requirements and the current practice of plan approval procedure are the main issue of the lectures which discuss aspects of environmental impact statements, consideration of ecological requirements, and the role of the landscape conservation plan accompanying official project planning documents. (HSCH) [de

10 CFR 431.444 - Test procedures for the measurement of energy efficiency.

Science.gov (United States)

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Test procedures for the measurement of energy efficiency. 431.444 Section 431.444 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY EFFICIENCY PROGRAM FOR... procedures for the measurement of energy efficiency. (a) Scope. Pursuant to section 346(b)(1) of EPCA, this...

49 CFR 572.124 - Thorax assembly and test procedure.

Science.gov (United States)

2010-10-01

... test procedure in paragraph (c) of this section: (1) The maximum sternum displacement (compression... displacement but before reaching the minimum required 38.0 mm (1.5 in) sternum displacement limit shall not exceed 1500 N (337.2 lbf). (2) The internal hysteresis of the ribcage in each impact as determined by the...

Credit Risk Management - Loan Approval Process

Directory of Open Access Journals (Sweden)

Lulzim Rashiti

2016-03-01

Full Text Available The aim of this study is on understanding the international regulations issued by Basel I, Basel II and Basel III to best supervise and manage credit risk management policies. Part of paper will focus on the description and impacts of the regulations and the pivotal importance they play in providing a sound banking system. Credit risk represents another important element that will be analysed considering that it lays the foundation during the loan consideration and approval process. The paper will also explain in detail procedures and responsibilities shared along the process of loan acceptance by a banker. To sum up, the overall process from application to loan approval or denial will be explained pointing out the implications that are faced along the way

40 CFR 1043.50 - Approval of methods to meet Tier 1 retrofit NOX standards.

Science.gov (United States)

2010-07-01

... retrofit NOX standards. 1043.50 Section 1043.50 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... SUBJECT TO THE MARPOL PROTOCOL § 1043.50 Approval of methods to meet Tier 1 retrofit NOX standards. Regulation 13 of Annex VI provides for certification of Approved Methods, which are retrofit procedures that...

In-Trail Procedure Air Traffic Control Procedures Validation Simulation Study

Science.gov (United States)

Chartrand, Ryan C.; Hewitt, Katrin P.; Sweeney, Peter B.; Graff, Thomas J.; Jones, Kenneth M.

2012-01-01

In August 2007, Airservices Australia (Airservices) and the United States National Aeronautics and Space Administration (NASA) conducted a validation experiment of the air traffic control (ATC) procedures associated with the Automatic Dependant Surveillance-Broadcast (ADS-B) In-Trail Procedure (ITP). ITP is an Airborne Traffic Situation Awareness (ATSA) application designed for near-term use in procedural airspace in which ADS-B data are used to facilitate climb and descent maneuvers. NASA and Airservices conducted the experiment in Airservices simulator in Melbourne, Australia. Twelve current operational air traffic controllers participated in the experiment, which identified aspects of the ITP that could be improved (mainly in the communication and controller approval process). Results showed that controllers viewed the ITP as valid and acceptable. This paper describes the experiment design and results.

75 FR 59717 - Agency Information Collection Activities: Announcement of Board Approval Under Delegated...

Science.gov (United States)

2010-09-28

..., New Executive Office Building, Room 10235, Washington, DC 20503. Final approval under OMB delegated... a bank shall establish and maintain written policies and procedures to prevent excessive exposure to... selecting correspondents and terminating those relationships. The policies and procedures should be reviewed...

76 FR 24372 - Approval and Promulgation of Air Quality Implementation Plans; Delaware; Update to Materials...

Science.gov (United States)

2011-05-02

... revised the procedures for incorporating by reference Federally- approved SIPs, as a result of... document, IBR procedures and ``Identification of plan'' format are discussed in further detail in the May...) of the Administrative Procedures Act (APA) which, upon finding ``good cause,'' authorizes agencies to...

ASK Procedure for Instrumented Pre-cracked Charpy-Type Tests

International Nuclear Information System (INIS)

Varga, T.; Njo, D.H.; Prantl, G.

1981-01-01

The essential technical content of the ASK procedure originated from development work in Switzerland since 1963, and practical experiences gained since 1972. The remainder of the content and the format of the procedure are based on the ASTM E 24.03.03. (Tentative Draft Copy) 'Proposed Method for Pre-cracked Charpy Impact and Slow-Bend Testing of Metallic Materials' by C. E. Harbower, 1973. Two different velocities, 5 m/s and 0.1 m/s were used with a Schnadt-type machine of rigid construction. The stiffness of the machine proved to be very suitable for instrumented testing. The instrumented Schnadt-Type machine was equipped with strain gauges both on the top of the pendulum and on the chisel. A static force calibration was followed by energy calibration, comparing potential energy losses with the area under the force-deflection curve. Deflection was measured using a high frequency eddy current method on the pendulum, and for slow testing by means of an inductive gauge on the chisel. Charpy-Type specimens of 1.0 mm max notch depth and 0.12 mm max notch radius were pre-cracked using a resonant fatigue testing machine, or an eccentric drive machine. Crack propagation rate da/dN was measured using 'Russenberger' measuring gauges. In addition a new technique for the detection of dynamic crack initiation, developed at the Institute of Research and Technology (TVFA) in Vienna is discussed and some results presented

Statistical approach for collaborative tests, reference material certification procedures

International Nuclear Information System (INIS)

Fangmeyer, H.; Haemers, L.; Larisse, J.

1977-01-01

The first part introduces the different aspects in organizing and executing intercomparison tests of chemical or physical quantities. It follows a description of a statistical procedure to handle the data collected in a circular analysis. Finally, an example demonstrates how the tool can be applied and which conclusion can be drawn of the results obtained

A procedure for the significance testing of unmodeled errors in GNSS observations

Science.gov (United States)

Li, Bofeng; Zhang, Zhetao; Shen, Yunzhong; Yang, Ling

2018-01-01

It is a crucial task to establish a precise mathematical model for global navigation satellite system (GNSS) observations in precise positioning. Due to the spatiotemporal complexity of, and limited knowledge on, systematic errors in GNSS observations, some residual systematic errors would inevitably remain even after corrected with empirical model and parameterization. These residual systematic errors are referred to as unmodeled errors. However, most of the existing studies mainly focus on handling the systematic errors that can be properly modeled and then simply ignore the unmodeled errors that may actually exist. To further improve the accuracy and reliability of GNSS applications, such unmodeled errors must be handled especially when they are significant. Therefore, a very first question is how to statistically validate the significance of unmodeled errors. In this research, we will propose a procedure to examine the significance of these unmodeled errors by the combined use of the hypothesis tests. With this testing procedure, three components of unmodeled errors, i.e., the nonstationary signal, stationary signal and white noise, are identified. The procedure is tested by using simulated data and real BeiDou datasets with varying error sources. The results show that the unmodeled errors can be discriminated by our procedure with approximately 90% confidence. The efficiency of the proposed procedure is further reassured by applying the time-domain Allan variance analysis and frequency-domain fast Fourier transform. In summary, the spatiotemporally correlated unmodeled errors are commonly existent in GNSS observations and mainly governed by the residual atmospheric biases and multipath. Their patterns may also be impacted by the receiver.

EFAM GTP 02 - the GKSS test procedure for determining the fracture behaviour of materials

International Nuclear Information System (INIS)

Schwalbe, K.H.; Heerens, J.; Zerbst, U.; Kocak, M.

2002-01-01

This document describes a unified fracture mechanics test method in procedural form for quasi-static testing of materials. It is based on the ESIS Procedures P1 and P2 and introduces additional features, such as middle cracked tension specimens, shallow cracks, the δ 5 crack tip opening displacement, the crack tip opening angle, the rate of dissipated energy, testing of weldments, and guidance for statistical treatment of scatter. Special validity criteria are given for tests on specimens with low constraint. This document represents an updated version of EFAM GTP 94. (orig.) [de

AIChe equipment testing procedure centrifugal compressors : a guide to performance evaluation and site testing

CERN Document Server

AIChE

2013-01-01

With its engineer-tested procedures and thorough explanations, Centrifugal Compressors is an essential text for anyone engaged in implementing new technology in equipment design, identifying process problems, and optimizing equipment performance.  This condensed book presents a step by step approach to preparing for, planning, executing, and analyzing tests of centrifugal compressors, with an emphasis on methods that can be conducted on-site and with an acknowledgement of the strengths and limitations of these methods. The book opens with an extensive and detailed section offering definitions

COLLABORATIVE PROCEDURE TO ACHIEVE AN EFFECTIVE JURISDICTIONAL TUTELAGE

Directory of Open Access Journals (Sweden)

Darilê Marques da Matta

2015-12-01

Full Text Available Set in a constitutional context, the procedure should be an effective instrument for the guarantee and realization of rights. Attentive to the needs imposed by the state of Law, the new Civil Procedure Code, approved this year, 2 015, seeks to settle several constitutional guarantees, for the purpose of making the procedure more effective. From the inclusion of collaborative institutes, the new Civil Procedure C ode introduces the concept of self-composition and cooperation of procedural agents to achieve, timely, effective jurisdictional tutelage.

Space Geodesy Project Information and Configuration Management Procedure

Science.gov (United States)

Merkowitz, Stephen M.

2016-01-01

This plan defines the Space Geodesy Project (SGP) policies, procedures, and requirements for Information and Configuration Management (CM). This procedure describes a process that is intended to ensure that all proposed and approved technical and programmatic baselines and changes to the SGP hardware, software, support systems, and equipment are documented.

Verification of examination procedures in clinical laboratory for imprecision, trueness and diagnostic accuracy according to ISO 15189:2012: a pragmatic approach.

Science.gov (United States)

Antonelli, Giorgia; Padoan, Andrea; Aita, Ada; Sciacovelli, Laura; Plebani, Mario

2017-08-28

Background The International Standard ISO 15189 is recognized as a valuable guide in ensuring high quality clinical laboratory services and promoting the harmonization of accreditation programmes in laboratory medicine. Examination procedures must be verified in order to guarantee that their performance characteristics are congruent with the intended scope of the test. The aim of the present study was to propose a practice model for implementing procedures employed for the verification of validated examination procedures already used for at least 2 years in our laboratory, in agreement with the ISO 15189 requirement at the Section 5.5.1.2. Methods In order to identify the operative procedure to be used, approved documents were identified, together with the definition of performance characteristics to be evaluated for the different methods; the examination procedures used in laboratory were analyzed and checked for performance specifications reported by manufacturers. Then, operative flow charts were identified to compare the laboratory performance characteristics with those declared by manufacturers. Results The choice of performance characteristics for verification was based on approved documents used as guidance, and the specific purpose tests undertaken, a consideration being made of: imprecision and trueness for quantitative methods; diagnostic accuracy for qualitative methods; imprecision together with diagnostic accuracy for semi-quantitative methods. Conclusions The described approach, balancing technological possibilities, risks and costs and assuring the compliance of the fundamental component of result accuracy, appears promising as an easily applicable and flexible procedure helping laboratories to comply with the ISO 15189 requirements.

42 CFR 488.60 - Special procedures for approving end stage renal disease facilities.

Science.gov (United States)

2010-10-01

... of the Public Health Service concerning the facility's contribution to the ESRD services of the network. (3) Data concerning the facility's compliance with professional norms and standards. (4) Data pertaining to the facility's qualifications for approval or for any expansion of services. (b) Determining...

Acceptance test procedure, 241-SY-101/241-C-106 shot loading system

International Nuclear Information System (INIS)

Ostrom, M.J.

1994-01-01

This Acceptance Test Procedure is for the 241-SY-101/241-C-106 Shot Loading System. The procedure will test the components of the Shot Loading System and its capability of adequately loading shot into the annular space of the Container. The loaded shot will provide shielding as required for transporting and storage of a contaminated pump after removal from the tank. This test serves as verification that the SLS is acceptable for use in the pump removal operations for Tanks 241-SY-101, 241-C-106 and 241-AY-102. The pump removal operation for these three tanks will be performed by two different organizations with different equipment, but the Shot Loading System will be compatible between the two operations

Equating Multidimensional Tests under a Random Groups Design: A Comparison of Various Equating Procedures

Science.gov (United States)

Lee, Eunjung

2013-01-01

The purpose of this research was to compare the equating performance of various equating procedures for the multidimensional tests. To examine the various equating procedures, simulated data sets were used that were generated based on a multidimensional item response theory (MIRT) framework. Various equating procedures were examined, including…

77 FR 28673 - Energy Conservation Program for Consumer Products: Test Procedures for Residential Furnace Fans

Science.gov (United States)

2012-05-15

... multipliers based on climate, consumer behavior assumptions, and product characteristics (e.g., multi-stage or... Conservation Program for Consumer Products: Test Procedures for Residential Furnace Fans; Proposed Rule #0;#0... Conservation Program for Consumer Products: Test Procedures for Residential Furnace Fans AGENCY: Office of...

Aviation Maintenance Technology. Course Content Guides. FAA Approved Curriculum.

Science.gov (United States)

Shrawder, Jack; And Others

Course content guides are provided for the 30 courses in this aviation maintenance technology curriculum approved by the Federal Aviation Administration. Course titles are physics for technicians; aircraft information, regulations, and procedures; aircraft assembly; fundamentals of aircraft electronics; aircraft electrical components; aircraft…

A simplified test procedure for determining the effectiveness of adsorbents for the removal of methyl iodide

International Nuclear Information System (INIS)

Underhill, D.W.

1993-01-01

ASTM Test Procedure D3803 measures the ability of nuclear-grade carbon to remove methyl iodide from a stream of humidified air. This test, unlike all the other procedures developed by ASTM Committee D28, has evolved to become extremely complex. The intricacy of this test as well as the great difficulty in obtaining inter-laboratory agreement, creates doubt as tot the actual meaning of the results. Here a far simpler test system is described in which thermodynamic principles are used to maintain a constant, reproducible test procedure. This paper describes a system implementing these elements, its cost to build, and the factors affecting its accuracy. 11 refs., 1 fig

78 FR 11984 - Approval and Promulgation of Implementation Plans; State of Hawaii; Update to Materials...

Science.gov (United States)

2013-02-21

... procedures for incorporating by reference federally-approved SIPs, as a result of consultations between EPA... procedures and ``Identification of plan'' format are discussed in further detail in the May 22, 1997 Federal... cause'' exemption in section 553(b)(3)(B) of the Administrative Procedures Act (APA) which, upon finding...

Acceptance Test Procedure for New Pumping and Instrumentation Control Skid M

International Nuclear Information System (INIS)

KOCH, M.R.

1999-01-01

This Acceptance Test Procedure (ATP) verifies proper construction per the design drawings and tests for proper functioning of the Pumping and Instrumentation Control (PIC) skid ''M''. The Scope section lists the systems and functions to be checked. This ATP will be performed at the Site Fabrication Service's (SFS) shop upon completion of construction of the PIC skid

Acceptance Test Procedure for New Pumping Instrumentation and Control Skid ''V''

International Nuclear Information System (INIS)

KOCH, M.R.

2000-01-01

This Acceptance Test Procedure (ATP) verifies proper construction per the design drawings and tests for proper functioning of the Pumping Instrumentation and Control (PIC) skid ''V''. The scope section lists the systems and functions to be checked. This ATP will be performed at the Site Fabrication Services (SFS) shop upon completion of the construction of the PIC skid

Dispersant field testing : a review of procedures and considerations

International Nuclear Information System (INIS)

Fingas, M.F.

2004-01-01

The effectiveness of a dispersant is defined by the amount of oil that the dispersant puts into the water column compared to the amount of oil that was initially spilled. Effectiveness is generally determined visually in plumes of dispersed oil that are visible from ships and aircraft. This paper describes 25 specific issues and technical concerns regarding field testing of dispersant effectiveness. Recent field tests were reviewed and literature that relates to testing procedures was sited. The 25 factors that are important for the appropriate outcome of dispersant field experiments include: mass balance; proper controls; analytical method; differential plume movement; time lag and length of time followed; mathematics of calculation and integration; lower and upper limits of analytical methods; use of remote sensing; thickness measurement; behaviour of oil with surfactant content; surfactant stripping; tracking surface oil and dispersed oil; recovering surface oil; visibility of oil from the surface; background levels of hydrocarbons; fluorescence of dispersant; herding; emulsion breaking; application success; heterogeneity of slick and plume; deposition measurements; true analytical standards; effect of wind on dispersant and slick; dispersant run-off; and weathering of the oil. It was concluded that the most important factors are the ability to determine mass balance, use proper controls, analytical methods and to avoid procedures that give incorrect results. 34 refs., 4 tabs., 1 fig

75 FR 82074 - Fee Adjustment for Testing, Evaluation, and Approval of Mining Products

Science.gov (United States)

2010-12-29

..., and Approval of Mining Products AGENCY: Mine Safety and Health Administration (MSHA), Labor. ACTION..., evaluating, and approving mining products as provided by 30 CFR part 5. MSHA charges applicants a fee to... materials manufactured for use in the mining industry. The new fee schedule, effective January 1, 2011, is...

Communication with patients during the prenatal testing procedure: an explorative qualitative study

NARCIS (Netherlands)

van Zwieten, Myra; Willems, Dick; Knegt, Lia; Leschot, Nico

2006-01-01

OBJECTIVE: While generally two phases of prenatal genetic counseling are distinguished, i.e. pre- and post-test counseling, we revealed a third form of communication during the testing procedure. The content of this intermediate communication was explored. METHODS: A secondary analysis was performed

Alternative procedure for the cold test for soybean seeds Procedimento alternativo para o teste de frio em semente de soja

Directory of Open Access Journals (Sweden)

Bruno Guilherme Torres Licursi Vieira

2010-10-01

Full Text Available The growing demand for high quality soybean [Glycine max (L. Merrill] seeds requires a precise seed quality control system from the seed industry. One way to accomplish this is by improving vigor testing. Cold test has been traditionally employed for corn seeds. However, it has also been used for other seed crops such as cotton (Gossypium spp., soybean (Glycine Max, dry bean (Phaseolus vulgaris and pea (Pisum sativum. This study was carried out with the objective of adjusting an alternative procedure for the cold test to determine soybean seed vigor. Six commercial soybean seed lots of the cultivar BRS 133 were used. The physiological potential of the seed lots was evaluated by germination on paper towel and sand box, seedling field emergence, tetrazolium, accelerated aging and electrical conductivity tests. Seed moisture content was also determined. The temperature used for the cold test procedures was 10ºC during five days. Four cold test procedures were evaluated: i plastic boxes with soil; ii rolled paper towel with soil; iii rolled paper towel without soil, and iv an alternative procedure, using rolled paper towel without soil under cold water. A completely randomized experimental design with eight replications was used and the means were compared by the Tukey test (p = 0.05. To verify the dependence between the alternative test and others single linear correlation was used. All cold test procedures had similar coefficients of variation (CV, highlighting that rolled paper towel with soil and the alternative procedure had the best performance, with an average of 94% and 93% normal seedlings and CV of 3.2% and 3.6%, respectively. The alternative procedure has satisfactory results for estimating soybean seed vigor, yielding consistent results compared to the traditional procedure.A crescente demanda por semente de soja [Glycine max (L. Merrill] de alta qualidade tem requerido da indústria de sementes um controle de qualidade mais preciso

In situ impulse test: an experimental and analytical evaluation of data interpretation procedures

International Nuclear Information System (INIS)

1975-08-01

Special experimental field testing and analytical studies were undertaken at Fort Lawton in Seattle, Washington, to study ''close-in'' wave propagation and evaluate data interpretation procedures for a new in situ impulse test. This test was developed to determine the shear wave velocity and dynamic modulus of soils underlying potential nuclear power plant sites. The test is different from conventional geophysical testing in that the velocity variation with strain is determined for each test. In general, strains between 10 -1 and 10 -3 percent are achieved. The experimental field work consisted of performing special tests in a large test sand fill to obtain detailed ''close-in'' data. Six recording transducers were placed at various points on the energy source, while approximately 37 different transducers were installed within the soil fill, all within 7 feet of the energy source. Velocity measurements were then taken simultaneously under controlled test conditions to study shear wave propagation phenomenology and help evaluate data interpretation procedures. Typical test data are presented along with detailed descriptions of the results

40 CFR 63.1365 - Test methods and initial compliance procedures.

Science.gov (United States)

2010-07-01

... permit limit applicable to the process vent. (D) Design analysis based on accepted chemical engineering... concentration, temperature, and the reaction kinetics of the constituents with the scrubbing liquid. The design... procedures specified in Method 8260 or 8270 in “Test Methods for Evaluating Solid Waste, Physical/Chemical...

75 FR 8526 - Procedures for Transportation Workplace Drug and Alcohol Testing Programs

Science.gov (United States)

2010-02-25

... 2105-AD64 Procedures for Transportation Workplace Drug and Alcohol Testing Programs AGENCY: Office of... required method. However, in response to comments requesting additional flexibility in testing methods, the... may increase flexibility and lower costs for employers who choose to use them over more expensive...

Recommended procedures for performance testing of radiobioassay laboratories: Volume 2, In vitro samples

International Nuclear Information System (INIS)

Fenrick, H.W.; MacLellan, J.A.

1988-11-01

Draft American National Standards Institute (ANSI) Standard N13.30 (Performance Criteria for Radiobioassay) was developed for the US Department of Energy and the US Nuclear Regulatory Commission to help ensure that bioassay laboratories provide accurate and consistent results. The draft standard specifies the criteria for defining the procedures necessary to establish a bioassay performance-testing laboratory and program. The bioassay testing laboratory will conduct tests to evaluate the performance of service laboratories. Pacific Northwest Laboratory helped develop testing procedures as part of an effort to evaluate the performance criteria by testing the existing measurement capabilities of various bioassay laboratories. This report recommends guidelines for the preparation, handling, storage, distribution, shipping, and documentation of in vitro test samples (artificial urine and fecal matter) for indirect bioassay. The data base and recommended records system for documenting radiobioassay performance at the service laboratories are also presented. 8 refs., 3 tabs

Acceptance test procedure for Project W-049H

International Nuclear Information System (INIS)

Buckles, D.I.

1994-01-01

The Acceptance Test Procedure (ATP) program for Project W-049H (200 Area Treated Effluent Disposal Facility [TEDF]) covers three activities as follows: (1) Disposal System; (2) Collection System; and (3) Instrumentation and Control System. Each activity has its own ATP. The purpose of the ATPs is to reverify that the systems have been constructed in accordance with the construction documents and to demonstrate that the systems function as required by the Project criteria. The Disposal System ATP covers the testing of the following: disposal line flowmeters, room air temperatures in the Disposal Station Sampling Building, effluent valves and position indicators, disposal pond level monitors, automated sampler, pressure relief valves, and overflow diversion sluice gates. The Collection System ATP covers the testing of the two pump stations and all equipment installed therein. The Instrumentation and Control (I and C) ATP covers the testing of the entire TEDF I and C system. This includes 3 OCS units, modem, and GPLI cabinets in the ETC control room; 2 pump stations; disposal station sampling building; and all LCUs installed in the field

Thermocouple module halt failure acceptance test procedure for Tank 241-SY-101 DACS-1

International Nuclear Information System (INIS)

Ermi, A.M.

1997-01-01

The readiness of the Tank 241-SY-101 Data Acquisition and Control System (DACS-1) to provide monitoring and alarms for a halt failure of any thermocouple module will be tested during the performance of this procedure. Updated DACS-1 ''1/0 MODULE HEALTH STATUS'', ''MININ1'', and ''MININ2'' screens, which now provide indication of thermocouple module failure, will also be tested as part of this procedure

Recommended procedures for performance testing of radiobioassay laboratories: Volume 1, Quality assurance

International Nuclear Information System (INIS)

Fenrick, H.W.; MacLellan, J.A.

1988-11-01

Draft American National Standards Institute (ANSI) Standard N13.30 (Performance Criteria for Radiobioassay) was developed in response to a concern expressed by the US Department of Energy and US Nuclear Regulatory Commission to help ensure that bioassay laboratories provide accurate and consistent results. The draft standard specifies the criteria for defining the procedures necessary to establish a bioassay performance-testing laboratory and program. The testing laboratory will conduct tests to evaluate the performance of service laboratories. Pacific Northwest Laboratory helped define responsibilities and develop procedures as part of an effort to evaluate the draft ANSI N13.30 performance criteria for quality assurance at bioassay laboratories. This report recommends elements of quality assurance and quality control responsibilities for the bioassay performance-testing laboratory program, including the qualification and performance of personnel and the calibration, certification, and performance of equipment. The data base and recommended records system for documenting radiobioassay performance at the service laboratories are also presented. 15 refs

Project W-049H collection system Acceptance Test Procedure

International Nuclear Information System (INIS)

Carrigan, M.C.

1994-01-01

The purpose of this Acceptance Test Procedure (ATP) for the Project W-049H, Treated Effluent Disposal Facility, is to verify that the collection system equipment installed as Pump Station No. 1 (225-W) and Pump Station No. 2 (225-E) have been installed in accordance with the design documents and function as required by the project criteria. This will be a wet test with potable water being introduced into the pump pits to test for leakage. Potable water will also be employed in the testing of the pumps and related mechanical equipment. All Instrument and Control equipment related to the pump stations will be checked electronically with simulated inputs/outputs when actual input/output signals are unavailable. Water from Pump Station 1 will be moved through the TEDF piping system and discharged into the disposal ponds. This will check the proper function of the air/vac valves not tested during construction, and the automated samplers

Operability test procedure for the Rotary Mode Core Sampling System Exhausters 3 and 4

International Nuclear Information System (INIS)

WSaldo, E.J.

1995-01-01

This document provides a procedure for performing operability testing of the Rotary Mode Core Sampling System Exhausters 3 ampersand 4. Upon completion of testing activities an operability testing report will be issued

Radiochemical analyses of several spent fuel Approved Testing Materials

International Nuclear Information System (INIS)

Guenther, R.J.; Blahnik, D.E.; Wildung, N.J.

1994-09-01

Radiochemical characterization data are described for UO 2 and UO 2 plus 3 wt% Gd 2 O 3 commercial spent nuclear fuel taken from a series of Approved Testing Materials (ATMs). These full-length nuclear fuel rods include MLA091 of ATM-103, MKP070 of ATM-104, NBD095 and NBD131 of ATM-106, and ADN0206 of ATM-108. ATMs 103, 104, and 106 were all irradiated in the Calvert Cliffs Nuclear Power Plant (Reactor No.1), a pressurized-water reactor that used fuel fabricated by Combustion Engineering. ATM-108 was part of the same fuel bundle designed as ATM-105 and came from boiling-water reactor fuel fabricated by General Electric and irradiated in the Cooper Nuclear Power Plant. Rod average burnups and expected fission gas releases ranged from 2,400 to 3,700 GJ/kgM. (25 to 40 Mwd/kgM) and from less than 1% to greater than 10%, respectively, depending on the specific ATM. The radiochemical analyses included uranium and plutonium isotopes in the fuel, selected fission products in the fuel, fuel burnup, cesium and iodine on the inner surfaces of the cladding, 14 C in the fuel and cladding, and analyses of the gases released to the rod plenum. Supporting examinations such as fuel rod design and material descriptions, power histories, and gamma scans used for sectioning diagrams are also included. These ATMs were examined as part of the Materials Characterization Center Program conducted at Pacific Northwest Laboratory provide a source of well-characterized spent fuel for testing in support of the US Department of Energy Office of Civilian Radioactive Waste Management Program

32 CFR 93.5 - Procedures.

Science.gov (United States)

2010-07-01

... SERVICE OF PROCESS; RELEASE OF OFFICIAL INFORMATION IN LITIGATION; AND TESTIMONY BY NSA PERSONNEL AS WITNESSES § 93.5 Procedures. (a) Release of official information in litigation. NSA personnel shall not..., but a record of such approval will be made and retained in the OGC. NSA personnel shall not provide...

77 FR 28519 - Test Procedure Guidance for Room Air Conditioners, Residential Dishwashers, and Residential...

Science.gov (United States)

2012-05-15

... Guidance for Room Air Conditioners, Residential Dishwashers, and Residential Clothes Washers: Public... procedures for room air conditioners, residential dishwashers, and residential clothes washers. DATES: DOE...'s existing test procedures for residential room air conditioners, residential dishwashers, and...

Some Remarks on Foundation Pile Testing Procedures

Science.gov (United States)

Rybak, Jarosław

2017-10-01

This work presents the review of pile capacity testing techniques. In an overview, the key points in pile designing are: determination of the appropriate computational schemes, reliable data on loads and the properties of structural materials (in particular, of the soil mass, which is marked by the greatest variability). The procedure of constructing a pile foundation should include: carrying out soil tests in the scope that ensures safe designing, selecting a piling technology that is relevant both to geotechnical conditions and expected loads, drafting a piling design together with the design of load tests, setting up a testing station for further load tests, static and/or dynamic tests of pile load capacity, preceded by supplementary soil tests when the conditions of test pile installation fail to comply with the design assumptions or when the pile length exceeds the depth of the previously investigated soil, making documentation of load capacity tests (with an additional correction of the piling design), the actual piling (ongoing analysis of pile driving logs and, if necessary, testing the piles’ integrity), drawing up the as-built documentation. Unfortunately, the design is corrected after the load test have been conducted only if the piles fail to show the designed bearing capacity. The designer is then obliged to revise the design assumptions on the basis of tests results. If the test results account for the a greater bearing capacity than necessary and it would be recommendable to limit the extent of the planned (i.e. set out in the contract) piling works, usually neither the contractor nor the designer, nor even the Construction Site Supervisor, acting for the benefit of the Investor, are willing to take on the responsibility for reducing the scope of the piling works. The necessity of conducting additional control tests before and during the implementation of the construction project is often treated by the investors as an attempt at extorting extra

14 CFR 151.29 - Procedures: Offer, amendment, and acceptance.

Science.gov (United States)

2010-01-01

... resolution or ordinance must, as appropriate under the local law— (1) Set forth the terms of the offer at... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Procedures: Offer, amendment, and... § 151.29 Procedures: Offer, amendment, and acceptance. (a) Upon approving a project, the Administrator...

Enraf series 854 Advanced Technology Gauge (ATG) acceptance test procedure. Revision 3

International Nuclear Information System (INIS)

Barnes, G.A.

1995-01-01

This procedure provides acceptance testing for Enraf Series 854 level gauges used to monitor levels in Hanford Waste Storage Tanks. The test will verify that the gauge functions according to the manufacturer's instructions and specifications and is properly setup prior to being delivered to the tank farm area

76 FR 69869 - Energy Conservation Program: Test Procedures for Residential Clothes Washers

Science.gov (United States)

2011-11-09

... ensure that the test procedure is representative of consumer behavior and repeatable among different test... would not be factored into its energy efficiency rating. This would imply that consumer behavior would... previous section, DOE does not have data to verify how consumers may adjust their behavior based on the...

48 CFR 9.307 - Government administration procedures.

Science.gov (United States)

2010-10-01

..., First Article Approval—Government Testing; and (3) Request that the activity inform the contract... other activity responsible for first article testing or evaluation shall inform the contracting office whether to approve, conditionally approve, or disapprove the first article. The contracting officer shall...

New test procedure to determine fuel's knock resistance; Neues Kraftstoffpruefverfahren zur Bestimmung der Klopffestigkeit

Energy Technology Data Exchange (ETDEWEB)

Huber, Karl [Hochschule Ingolstadt (Germany). Thermodynamik und Verbrennungsmotoren; Hauber, Johann; Raba, Andreas [Hochschule Ingolstadt (Germany). Inst. fuer Angewandte Forschung; Nell, Robert [Rofa Laboratory and Process Analyzers, Kritzendorf (Austria). Bereich Produktentwicklung

2013-07-15

Knock resistance is one of the most important quality features of gasoline that is determined by standardised motor test procedures. These procedures were developed more than 80 years ago and have been used nearly unchanged since then. During a four-year research project at Ingolstadt University of Applied Sciences, the procedures for determination of octane numbers were analysed in order to develop a new engine-based test method. (orig.)

Academic Program Approval and Review Practices

Directory of Open Access Journals (Sweden)

Don G. Creamer

1999-08-01

Full Text Available This report outlines general and specific processes for both program approval and program review practices found in 50 states and eight foreign countries and regions.  Models that depict these procedures are defined and the strengths and weakness of each are discussed.  Alternatives to current practice by state agencies in the U.S. are described that might provide for greater decentralization of these practices while maintaining institutional accountability.

77 FR 31443 - Energy Conservation Program: Test Procedures for Residential Dishwashers, Dehumidifiers, and...

Science.gov (United States)

2012-05-25

... an ion exchange to remove calcium and magnesium ions from the water, by swapping sodium ions bonded... addresses energy and water use associated with dishwasher water softeners, the energy test cycle for... dehumidifier test procedure, eliminate measurement of gas pilot light energy use in the cooking products test...

Hanford spent nuclear fuel cold vacuum drying proof of performance test procedure

International Nuclear Information System (INIS)

McCracken, K.J.

1998-01-01

This document provides the test procedure for cold testing of the first article skids for the Cold Vacuum Drying (CVD) process at the Facility. The primary objective of this testing is to confirm design choices and provide data for the initial start-up parameters for the process. The current scope of testing in this document includes design verification, drying cycle determination equipment performance testing of the CVD process and MCC components, heat up and cool-down cycle determination, and thermal model validation

30 CFR 18.81 - Field modification of approved (permissible) equipment; application for approval of modification...

Science.gov (United States)

2010-07-01

... TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC MOTOR-DRIVEN MINE EQUIPMENT AND ACCESSORIES... having jurisdiction at the mine where such equipment is to be operated stating the modifications which...

Vaspar broth-disk procedure for antibiotic susceptibility testing of anaerobic bacteria.

OpenAIRE

West, S E; Wilkins, T D

1980-01-01

A modification of the Wilkins-Thiel broth-disk procedure for antibiotic susceptibility testing of anaerobic bacteria is described. This method utilizes an aerobically prepared medium overlaid with molten vaspar. Specialized anaerobic techniques or prereduced media are not required.

7 CFR 1726.252 - Prior approved contract modification related to liability for special and consequential damages.

Science.gov (United States)

2010-01-01

... consequential damages on account of breach of this contract shall not exceed in total an amount equal to... 7 Agriculture 11 2010-01-01 2010-01-01 false Prior approved contract modification related to... CONSTRUCTION POLICIES AND PROCEDURES Modifications to RUS Standard Contract Forms § 1726.252 Prior approved...

Testing the applicability of the SASS5 scoring procedure for ...

African Journals Online (AJOL)

A study was undertaken between 29th January and 17th February 2004 to test the applicability of the South African Scoring System Version 5 (SASS5) scoring and calculation procedure in nutrient-enriched palustrine wetlands in the midlands of KwaZulu-Natal, South Africa. Four reference wetlands and three dairy-effluent ...

29 CFR 5.16 - Training plans approved or recognized by the Department of Labor prior to August 20, 1975.

Science.gov (United States)

2010-07-01

... 29 Labor 1 2010-07-01 2010-07-01 true Training plans approved or recognized by the Department of... STANDARDS ACT) Davis-Bacon and Related Acts Provisions and Procedures § 5.16 Training plans approved or... contractor shall be required to obtain approval of a training program which, prior to August 20, 1975, was...

Test procedures and instructions for Hanford complexant concentrate supernatant cesium removal using CST

Energy Technology Data Exchange (ETDEWEB)

Hendrickson, D.W.

1997-01-08

This document provides specific test procedures and instructions to implement the test plan for the preparation and conduct of a cesium removal test, using Hanford Complexant Concentrate supernatant liquor from tank 241-AN-107, in a bench-scale column. The cesium sorbent to be tested is crystalline silicotitanate. The test plan for which this provides instructions is WHC-SD-RE-TP-023, Hanford Complexant Concentrate Supernatant Cesium Removal Test Plan.

Set-up and Test Procedure for Suction Installation and Uninstallation of Bucket Foundation

DEFF Research Database (Denmark)

Koteras, Aleksandra Katarzyna

This technical report describes the set-up and the test procedures for installation and uninstallation of medium-scale model of bucket foundation that can be performed in the geotechnical part of laboratory in Aalborg University. The installation of bucket foundation can be tested with the use of......) and loading frame used for those tests have been already used for axially static and cyclic loading of piles (Thomassen, 2015a) and for axially static and cyclic loading of bucket foundation (Vaitkunaite et al., 2015).......This technical report describes the set-up and the test procedures for installation and uninstallation of medium-scale model of bucket foundation that can be performed in the geotechnical part of laboratory in Aalborg University. The installation of bucket foundation can be tested with the use...... of suction under the bucket lid or by applying additional force through the hydraulic piston, forcing the bucket to penetrate into the soil. Tests for uninstallation are performed also with the use of water pressure, as a reverse process to the suction installation. Both installation and uninstallation tests...

A Comparison of Procedures for Content-Sensitive Item Selection in Computerized Adaptive Tests.

Science.gov (United States)

Kingsbury, G. Gage; Zara, Anthony R.

1991-01-01

This simulation investigated two procedures that reduce differences between paper-and-pencil testing and computerized adaptive testing (CAT) by making CAT content sensitive. Results indicate that the price in terms of additional test items of using constrained CAT for content balancing is much smaller than that of using testlets. (SLD)

75 FR 14287 - Energy Conservation Program: Test Procedures for Fluorescent Lamp Ballasts

Science.gov (United States)

2010-03-24

... uses the same measurement techniques as the existing test procedure. In any rulemaking to amend a test...; and (3) appearing on page 29 of the transcript. \\6\\ Ballast type refers to a grouping of ballasts that... grouping of lamps that have the same length, lumen package, base type, and diameter. In the ongoing...

76 FR 65631 - Energy Conservation Program: Test Procedures for Microwave Ovens

Science.gov (United States)

2011-10-24

... Conservation Program: Test Procedures for Microwave Ovens AGENCY: Office of Energy Efficiency and Renewable... residential microwave ovens. DOE specifically is seeking information, data, and comments regarding representative and repeatable methods for measuring the energy use of microwave-only ovens and combination...

Selective versus routine patch metal allergy testing to select bar material for the Nuss procedure in 932 patients over 10years.

Science.gov (United States)

Obermeyer, Robert J; Gaffar, Sheema; Kelly, Robert E; Kuhn, M Ann; Frantz, Frazier W; McGuire, Margaret M; Paulson, James F; Kelly, Cynthia S

2018-02-01

The aim of the study was to determine the role of patch metal allergy testing to select bar material for the Nuss procedure. An IRB-approved (11-04-WC-0098) single institution retrospective, cohort study comparing selective versus routine patch metal allergy testing to select stainless steel or titanium bars for Nuss repair was performed. In Cohort A (9/2004-1/2011), selective patch testing was performed based on clinical risk factors. In Cohort B (2/2011-9/2014), all patients were patch tested. The cohorts were compared for incidence of bar allergy and resultant premature bar loss. Risk factors for stainless steel allergy or positive patch test were evaluated. Cohort A had 628 patients with 63 (10.0%) selected for patch testing, while all 304 patients in Cohort B were tested. Over 10years, 15 (1.8%) of the 842 stainless steel Nuss repairs resulted in a bar allergy, and 5 had a negative preoperative patch test. The incidence of stainless steel bar allergy (1.8% vs 1.7%, p=0.57) and resultant bar loss (0.5% vs 1.3%, p=0.23) was not statistically different between cohorts. An allergic reaction to a stainless steel bar or a positive patch test was more common in females (OR=2.3, pbar allergies occur at a low incidence with either routine or selective patch metal allergy testing. If selective testing is performed, it is advisable in females and patients with a personal or family history of metal sensitivity. A negative preoperative patch metal allergy test does not preclude the possibility of a postoperative stainless steel bar allergy. Level III Treatment Study and Study of Diagnostic Test. Copyright © 2017 Elsevier Inc. All rights reserved.

Validation of IEEE P1547.1 Interconnection Test Procedures: ASCO 7000 Soft Load Transfer System

Energy Technology Data Exchange (ETDEWEB)

Kroposki, B.; Englebretson, S.; Pink, C.; Daley, J.; Siciliano, R.; Hinton, D.

2003-09-01

This report presents the preliminary results of testing the ASCO 7000 Soft Load Transfer System according to IEEE P1547.1 procedures. The ASCO system interconnects synchronous generators with the electric power system and provides monitoring and control for the generator and grid connection through extensive protective functions. The purpose of this testing is to evaluate and give feedback on the contents of IEEE Draft Standard P1547.1 Conformance Tests Procedures for Equipment Interconnecting Distributed Resources With Electric Power Systems.

Valid methods: the quality assurance of test method development, validation, approval, and transfer for veterinary testing laboratories.

Science.gov (United States)

Wiegers, Ann L

2003-07-01

Third-party accreditation is a valuable tool to demonstrate a laboratory's competence to conduct testing. Accreditation, internationally and in the United States, has been discussed previously. However, accreditation is only I part of establishing data credibility. A validated test method is the first component of a valid measurement system. Validation is defined as confirmation by examination and the provision of objective evidence that the particular requirements for a specific intended use are fulfilled. The international and national standard ISO/IEC 17025 recognizes the importance of validated methods and requires that laboratory-developed methods or methods adopted by the laboratory be appropriate for the intended use. Validated methods are therefore required and their use agreed to by the client (i.e., end users of the test results such as veterinarians, animal health programs, and owners). ISO/IEC 17025 also requires that the introduction of methods developed by the laboratory for its own use be a planned activity conducted by qualified personnel with adequate resources. This article discusses considerations and recommendations for the conduct of veterinary diagnostic test method development, validation, evaluation, approval, and transfer to the user laboratory in the ISO/IEC 17025 environment. These recommendations are based on those of nationally and internationally accepted standards and guidelines, as well as those of reputable and experienced technical bodies. They are also based on the author's experience in the evaluation of method development and transfer projects, validation data, and the implementation of quality management systems in the area of method development.

SFC/SFBMN guidelines update for nuclear cardiology procedures: stress testing in adults and children

International Nuclear Information System (INIS)

Manrique, A.; Marie, P.Y.; Maunoury, Ch.; Acar, Ph.; Agostini, D.

2002-01-01

The guidelines update for nuclear cardiology procedures are studied in this article. We find the minimum technique conditions for the stress testing practice, the recommendations for the different ischemia activation tests, the choice of the stress test. (N.C.)

75 FR 5722 - Procedures for Transportation Workplace Drug and Alcohol Testing Programs

Science.gov (United States)

2010-02-04

... personal identifying information about an employee (other than a social security number (SSN) or other... testing required under this part. (c) As a drug testing laboratory located in Canada or Mexico which is... procedures. (d) As an IITF located in Canada or Mexico which is not certified by HHS under the NLCP, you are...

75 FR 42579 - Energy Conservation Program for Consumer Products: Test Procedure for Microwave Ovens; Repeal of...

Science.gov (United States)

2010-07-22

... provided in paragraph (i)(2) of this section, for each basic model of conventional cooking tops, and... the cooking efficiency test procedure for microwave ovens under the Energy Policy and Conservation Act (EPCA). DOE has determined that the microwave oven test procedure to measure the cooking efficiency does...

Aesthetic procedures in office practice.

Science.gov (United States)

Small, Rebecca

2009-12-01

Since the approval of botulinum toxin, dermal fillers, and lasers for cosmetic use, minimally invasive aesthetic procedures have rapidly become the treatments of choice for age-related facial changes. In the past 10 years, aesthetic procedures have increased nearly five-fold. Of the 10.2 million aesthetic treatments performed in 2008, 83 percent were minimally invasive procedures. Botulinum toxin and dermal filler injections, laser hair reduction, chemical peels, laser skin resurfacing, microdermabrasion, and intense pulsed light photorejuvenation were the most commonly performed procedures in 2008. These procedures are effective and associated with minimal discomfort, and they have a low incidence of adverse effects and short recovery times. High patient and physician satisfaction have contributed to their growing popularity and availability in the primary care setting. As patient demand for aesthetic treatments increases, family physicians should be familiar with common minimally invasive aesthetic procedures when advising patients or incorporating aesthetic care into office practice.

Standard Test Method for Sandwich Corrosion Test

CERN Document Server

American Society for Testing and Materials. Philadelphia

2009-01-01

1.1 This test method defines the procedure for evaluating the corrosivity of aircraft maintenance chemicals, when present between faying surfaces (sandwich) of aluminum alloys commonly used for aircraft structures. This test method is intended to be used in the qualification and approval of compounds employed in aircraft maintenance operations. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information. 1.3 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements appear in Section 9.

Initial land reclamation procedures related to possible Pu-cleanup activities at the Tonopah Test Range

International Nuclear Information System (INIS)

Wallace, A.; Romney, E.M.

1976-02-01

If areas of the Tonopah Test Range (TTR) are to be used for experimental tests of procedures for clean-up of 239 Pu contamination, there are experiences in the Great Basin Desert portions of the Nevada Test Site (NTS) which can serve as guides to reclamation and revegetation of such arid lands. Procedures which will encourage development of the grasses Hilaria jamesii and Oryzopsis hymenoides, as well as the perennial shrubs Eurotia lanata and Atriplex canescens would greatly improve the area as range land

Development of a Laboratory Test Procedure to Evaluate Tack Coat Performance

OpenAIRE

YILDIRIM, Yetkin; SMIT, André de Fortier; KORKMAZ, Armagan

2014-01-01

A laboratory testing procedure is presented, the results of which may be used for determining the best combination of tack coat type, mixture type, and application rate to be applied in the field for optimum performance. Tack coat related performance results were determined from Hamburg wheel tracking and simple shear tests on laboratory prepared specimens. This study was undertaken to evaluate the shear strength performance of tack coats under laboratory-controlled conditions. The ...

Measurement protocol for performance testing of the determination of tritium in water

International Nuclear Information System (INIS)

1993-01-01

In the Health and Safety Executive's ''Requirements for the Approval of Dosimetry Services under the Ionising Radiations Regulations 1985'', it is stipulated that dosimetry services seeking approval must show that they have successfully completed a performance test. The services must arrange for the tests to be carried out on application and thereafter every 18 months, by a laboratory which has received accreditation from the National Measurement Accreditation Service (NAMAS) for conducting the performance tests. Accreditation by NAMAS ensures that the laboratories carrying out the performance tests are of an appropriate standard. It includes requirements for quality control and audit procedures, to authenticate traceability to national standards, and to provide a reliable record keeping system for the performance tests. A list of laboratories which are accredited by NAMAS for carrying out HSE published performance tests will be maintained by the Secretary of the Dosimetry Services Panel. The performance tests must be carried out to published protocols. The results have to be expressed in terms of bias and random error, as defined in HSE's criteria for performance tests. The purpose here is to provide a protocol for laboratories to conduct performance tests on dosimetry services performing tritium determinations in urine. The test is deliberately not exhaustive, instead it is a simple test allowing the basic performance of a service to be assessed for approval. (author)

9 CFR 147.30 - Laboratory procedure recommended for the polymerase chain reaction (PCR) test for Mycoplasma...

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Laboratory procedure recommended for... Examination Procedures § 147.30 Laboratory procedure recommended for the polymerase chain reaction (PCR) test... tracheal swabs in PBS or 1 mL of broth culture by a non-phenolic procedure. Centrifuge samples at 14,000 x...

Studies of field test procedures in hydraulic turbines for SHP; Estudos de procedimentos de ensaios de campo em turbinas hidraulicas para PCH

Energy Technology Data Exchange (ETDEWEB)

Justino, Lucimary Aparecida

2006-07-01

A supply contract of equipment for Small Hydro Power, contain the power and turbine efficiency guarantees and can contain adds guarantees referring to a rotation and pressure variation, runaway speed and cavitations test. To the determination about the hydraulics turbines performance for contractual guarantees are realized the field acceptance test, that are methods quite a lot used for enterprises like tools to prove the contractual guarantees in substitution to model test, that showed a cost extremely high. In the field acceptance test are measures of some values that added to the others, possibility obtain the turbine efficiency. In the small hydro power, the turbine efficiency represents the hydraulic power percentage that is subject to be transformed in electrical power. In the turbine purchase, the manufacturer has to guarantee the efficiency specified if it is become down to expected, the damages are enormous, then the importance to exist precise methods and reliable for your measurement. The method accuracy of the discharge measurement that has, between another problems, the calibration and installation, that influence hard the value of the efficiency obtained. This work shows the different methodologies about discharge measurement in hydraulic turbines, that can be apply in Small Hydro Power field tests and shows too the procedures used that in specifics cases of small hydro, without quality damage, the site tests could be executed the form that the guarantees will be approve with compatible cots with the investment done. As an example for said above, are show two cases in small hydro where did realized field acceptance tests to assure the contractual guarantees. (author)

Amendment to the agreement between CERN and Ukraine concerning the granting of the status of Associate Member at CERN Extension of the deadline for the notification of the completion of the internal approval procedures of the agreement by Ukraine

CERN Document Server

2015-01-01

Amendment to the agreement between CERN and Ukraine concerning the granting of the status of Associate Member at CERN Extension of the deadline for the notification of the completion of the internal approval procedures of the agreement by Ukraine

Grate Pallet 8232 (GP-8232) Vehicle Pallet, Evaluation Tests MIL-STD-1660, "Design Criteria for Ammunition Unit Loads" and TP-94-01 (REV 1), "Transportability Testing Procedures"

National Research Council Canada - National Science Library

Barickman, Philip

2003-01-01

.... The testing was conducted for informational purposes only. The GP-8232 Vehicle Pallet was evaluated by the testing procedures set forth in MIL-STD-1660 and TP-94-01 (Rev. 1) testing procedures...

The AP600 advanced simplified nuclear power plant. Results of the test program and progress made toward final design approval

International Nuclear Information System (INIS)

Bruschi, H.J.

1996-01-01

At the 1994 Pacific Basin Conference, Mr. Bruschi presented a paper describing the AP600, Westinghouse's advanced light water reactor design with passive safety features. Since then, a rigorous test program was completed and AP600 became the most thoroughly tested advanced reactor system design in history. Westinghouse is now well on its way toward receiving Final Design Approval from the U.S. Nuclear Regulatory Commission for AP600. In this paper, the results of the test program will be discussed and an update on prospects for building the plant will be covered. (author)

The AP600 advanced simplified nuclear power plant. Results of the test program and progress made toward final design approval

Energy Technology Data Exchange (ETDEWEB)

Bruschi, H.J. [Westinghouse Electric Corp., Pittsburgh, PA (United States)

1996-10-01

At the 1994 Pacific Basin Conference, Mr. Bruschi presented a paper describing the AP600, Westinghouse`s advanced light water reactor design with passive safety features. Since then, a rigorous test program was completed and AP600 became the most thoroughly tested advanced reactor system design in history. Westinghouse is now well on its way toward receiving Final Design Approval from the U.S. Nuclear Regulatory Commission for AP600. In this paper, the results of the test program will be discussed and an update on prospects for building the plant will be covered. (author)

Test procedures to detect a loss of material in a sequence of balance periods

International Nuclear Information System (INIS)

Avenhaus, R.; Beedgen, R.; Sellinschegg, D.

1985-06-01

A workshop on Near-Real-Time Accountancy (NRTA) was held in KfK which came to a preliminary end in December 1982. In the framework of this workshop a number of sequential statistical test procedures were proposed which can be used in the case of a NRTA based safeguards regime. In the report the most promising test procedures are investigated. The analysis is based on the chemical separation process of a large model reprocessing facility with a throughput or 1000 tonnes per year. (orig.) [de

Operability test procedure for PFP wastewater sampling facility

International Nuclear Information System (INIS)

Hirzel, D.R.

1995-01-01

Document provides instructions for performing the Operability Test of the 225-WC Wastewater Sampling Station which monitors the discharge to the Treated Effluent Disposal Facility from the Plutonium Finishing Plant. This Operability Test Procedure (OTP) has been prepared to verify correct configuration and performance of the PFP Wastewater sampling system installed in Building 225-WC located outside the perimeter fence southeast of the Plutonium Finishing Plant (PFP). The objective of this test is to ensure the equipment in the sampling facility operates in a safe and reliable manner. The sampler consists of two Manning Model S-5000 units which are rate controlled by the Milltronics Ultrasonic flowmeter at manhole No.C4 and from a pH measuring system with the sensor in the stream adjacent to the sample point. The intent of the dual sampling system is to utilize one unit to sample continuously at a rate proportional to the wastewater flow rate so that the aggregate tests are related to the overall flow and thereby eliminate isolated analyses. The second unit will only operate during a high or low pH excursion of the stream (hence the need for a pH control). The major items in this OTP include testing of the Manning Sampler System and associated equipment including the pH measuring and control system, the conductivity monitor, and the flow meter

Operating experience and procedures at the tritium systems test assembly

International Nuclear Information System (INIS)

Carlson, R.V.; Binning, K.E.; Cole, S.P.; Jenkins, E.M.; Wilhelm, R.C.; Cole, S.P.

1988-01-01

Operating procedures are important for the safe and efficient operation of the Tritium Systems Test Assembly (TSTA). TSTA has been operating for four years with tritium in a safe and efficient manner. The inventory of tritium in the process loop is 100 grams and several milestone runs have been completed. This paper describes the methods used to operate TSTA. 3 refs., 1 fig

78 FR 15807 - Energy Conservation Program: Test Procedures for Television Sets

Science.gov (United States)

2013-03-12

... displaying dynamic visual content from wired or wireless sources including but not limited to: * * *''. DOE...) standard ``CEA-2037-A, Determination of Television Average Power Consumption'' into the SNOPR. In today's SNOPR, DOE proposes to update the input power requirements in the TVs test procedure NOPR by referencing...

40 CFR 205.54-1 - Low speed sound emission test procedures.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Low speed sound emission test procedures. 205.54-1 Section 205.54-1 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) NOISE ABATEMENT PROGRAMS TRANSPORTATION EQUIPMENT NOISE EMISSION CONTROLS Medium and Heavy Trucks § 205...

Test-Induced Priming Impairs Source Monitoring Accuracy in the DRM Procedure

OpenAIRE

Dewhurst, S.; Knott, L.; Howe, M. L.

2011-01-01

Three experiments investigated the effects of test-induced priming (TIP) on false recognition in the Deese/Roediger-McDermott procedure. In Experiment 1, TIP significantly increased false recognition for participants who made old/new decisions at test but not for participants who made remember/know judgements or were given diagnostic information to help them avoid false recognition. In Experiment 2, a TIP effect was observed with old/new recognition but not when participants were required to ...

Requirements for the approval of dosimetry services under the Ionising Radiations Regulations 1985: Pt. 1: External radiations

International Nuclear Information System (INIS)

1991-01-01

Guidance for dosimetry services on the requirements for approval by the Health and Safety Executive (HSE) is provided in three parts. This part sets out the procedures and criteria that will be used by HSE in the assessment of dosimetry services seeking approval in relation to external radiations (including accidents). (author)

Leach test of six 192-iridium pellets based on the IAEA 'special form' test procedures

International Nuclear Information System (INIS)

Gordon, G.; Gerdingh, R.

1981-07-01

The designation 'special form' may be applied to indispersible solid radioactive material if the material meets the requirements of the tests described in the International Atomic Energy Agency Regulations for the Safe Transport of Radioactive Type Materials. This report presents the procedures and results of a leach test performed as specified in the regulations on 6 'as received' active 192-iridium pellets. Mechanical tests were not carried out prior to or following the leach test. The activity of each of the first 6 water baths was found to be between 2.3 and 12.6 μCi, (8.5 x 10 4 and 4.7 x 10 5 Bq) and of the second 6, between 1.3 to 6.0 μCi, (4.8 x 10 4 to 2.2 x 10 5 Bq) thus exceeding the allowable limit

High-efficiency particulate air filter test activities at the Department of Energy

International Nuclear Information System (INIS)

Bresson, J.F.

1987-01-01

For the past 2 years, test activities at the three Department of Energy HEPA Filter Test Facilities (FTFs) have been conducted under a unified set of operating standards intended to help achieve consistency in test methods and test results. Reviews of test operations are conducted at each FTF annually, and technical support and guidance are provided on request. Round Robin tests are conducted twice a year to compare penetration and resistance test results among the three FTFs. The FTFs prepare summary test data twice a year, and the data is analyzed for trends with respect to ongoing quality of HEPA filters in nuclear facilities. Data and conclusions from both the Round Robin tests and semiannual reports are discussed, the latter without reference to specific manufacturers. The new DOE standards include provisions for consideration and approval of new test aerosols or test methods, under closely controlled change procedures. Progress in obtaining DOE approval for DOS as a new aerosol, and for the Alternative Test System (ATS) developed by, and reported on by the LANL, as an approved new test method are discussed, as are 2 significant changes in standard NE-F-3-43, related to (a) toxicology test alternatives, and (b) the test aerosol definition. Finally, the emergence of new, higher flow rated HEPA filters and Ultra Low Particulate Air (ULPA) filters will impact DOE's design, procurement, testing and use of HEPA filters in the near future

Safety panel and new procedures evaluation by simulator tests

International Nuclear Information System (INIS)

Meslin, T.

1986-01-01

With more than thirty weeks of simulator testing (for the last three years only) and approximately three hundred scenarios, EDF's experience in this field is extensive. This practice is well known within Fossil and Nuclear Generation and is well accepted by the operating teams which participate in it. Simulator testing appears to be an essential decision-making tool in the process of developing new operating aids in PWR plants. Accelerated development and the elimination of long and expensive modifications after commissioning is an economic advantage. The saving in time is obvious, since modifications are carried out continuously throughout the development phase. Finally, operators participate in the development of systems and receive fixed, well-defined applications. This practice has become systematic, and all new applications concerning the operation of PWR plants are simulator-tested, particularly 1300-MW unit computers and operating procedures, the new generation of 900-MW unit computers, and the new 1500-MW fully computerized control rooms. Finally, this simulator testing allows us to considerably increase our knowledge concerning the behavior of operators in accident situations, and special tests are performed for this purpose

Requirements for the approval of dosimetry services under the Ionising Radiations Regulations 1985: Pt. 2: Internal radiations

International Nuclear Information System (INIS)

1991-01-01

Guidance for dosimetry services on the requirements for approval by the Health and Safety Executive (HSE) is provided in three parts. This part sets out the procedures and criteria that will be used by HSE in the assessment of dosimetry services seeking approval in relation to internal radiations (including radon decay products). (author)

49 CFR 572.75 - Lumbar spine, abdomen, and pelvis assembly and test procedure.

Science.gov (United States)

2010-10-01

...) ANTHROPOMORPHIC TEST DEVICES 6-Year-Old Child § 572.75 Lumbar spine, abdomen, and pelvis assembly and test procedure. (a) Lumbar spine, abdomen, and pelvis assembly. The lumbar spine, abdomen, and pelvis consist of... 49 Transportation 7 2010-10-01 2010-10-01 false Lumbar spine, abdomen, and pelvis assembly and...

Operability test procedure for 211BA flow proportional sampler

International Nuclear Information System (INIS)

Weissenfels, R.D.

1994-01-01

The purpose of this operability test procedure (OTP) is to verify the 211-BA flow proportional sampler system and components function correctly as intended by design. System test will include the sampling system, all associated instrumentation, and Facility Process Monitor and Control System (FPMCS). The combined chemical sewer stream from B Plant flows through sump 211BA-SMP-01 located in 211-BA and is continuously monitored for gamma and beta radiation and pH. 211-BA has been upgraded to include a flow proportional sampler. A specified sample volume will be withdrawn at programmed intervals from the 211BA sump and deposited in a 19 liter plastic carboy. The sampler will be programmed per the vendor installation and operations manual by B Plant instrument maintenance personnel. Samples will be taken during five consecutive sample cycles with the sample volumes and sample frequencies recorded for comparison purposes. Additional tests related to the sampler include the alarm circuitry for loss of power and failure to obtain sample

Further investigations of the W-test for pairwise epistasis testing [version 1; referees: 2 approved

Directory of Open Access Journals (Sweden)

Richard Howey

2017-07-01

Full Text Available Background: In a recent paper, a novel W-test for pairwise epistasis testing was proposed that appeared, in computer simulations, to have higher power than competing alternatives. Application to genome-wide bipolar data detected significant epistasis between SNPs in genes of relevant biological function. Network analysis indicated that the implicated genes formed two separate interaction networks, each containing genes highly related to autism and neurodegenerative disorders. Methods: Here we investigate further the properties and performance of the W-test via theoretical evaluation, computer simulations and application to real data. Results: We demonstrate that, for common variants, the W-test is closely related to several existing tests of association allowing for interaction, including logistic regression on 8 degrees of freedom, although logistic regression can show inflated type I error for low minor allele frequencies,  whereas the W-test shows good/conservative type I error control. Although in some situations the W-test can show higher power, logistic regression is not limited to tests on 8 degrees of freedom but can instead be taylored to impose greater structure on the assumed alternative hypothesis, offering a power advantage when the imposed structure matches the true structure. Conclusions: The W-test is a potentially useful method for testing for association - without necessarily implying interaction - between genetic variants disease, particularly when one or more of the genetic variants are rare. For common variants, the advantages of the W-test are less clear, and, indeed, there are situations where existing methods perform better. In our investigations, we further uncover a number of problems with the practical implementation and application of the W-test (to bipolar disorder previously described, apparently due to inadequate use of standard data quality-control procedures. This observation leads us to urge caution in

75 FR 26183 - Procedures for Transportation Workplace Drug and Alcohol Testing Programs

Science.gov (United States)

2010-05-11

... 2105-AE01 Procedures for Transportation Workplace Drug and Alcohol Testing Programs AGENCY: Office of...: For program issues, Bohdan Baczara, Office of Drug and Alcohol Policy and Compliance, 1200 New Jersey... of Federal Regulations, as follows: [[Page 26184

Design of test and emergency procedures to improve operator behaviour in French nuclear power plants

International Nuclear Information System (INIS)

Griffon-Fouco, M.; Gomolinski, M.

1982-09-01

The incident analyses performed in French nuclear power plants high-lighted that deficiencies in the design of procedures are frequent causes of human errors. The process for developing new guidelines for the writing of test and emergency procedures is presented: this process is based on operators interviews and observations at the plants or at simulators. The main principles for the writing of procedures are developed. For example: - the elaboration of a procedure for action and of a separate educational procedure, - the coordination of crew responses, - the choice of vocabulary, graphs, flow charts and so on as regards the format. Other complementary actions, such as the training of operators in the use of procedures, are described

Design of test and emergency procedures to improve operator behavior in French nuclear power plants

International Nuclear Information System (INIS)

Griffon-Fouco, M.; Gomolinski, M.

1983-01-01

The incident analyses performed in French nuclear power plants high-lighted that deficiencies in the design of procedures are frequent causes of human errors. The process for developing new guidelines for the writing of test and emergency procedures is presented: this process is based on operators interviews and observations at the plants or at simulators. The main principles for the writing of procedures are developed. For example: the elaboration of a procedure for action and of separate educational procedure; the coordination of crew responses; and the choice of vocabulary, graphs, flow charts and so on as regards the format. Other complementary actions, such as the training of operators in the use of procedures, are described

34 CFR 299.11 - What items are included in the complaint procedures?

Science.gov (United States)

2010-07-01

... violations of section 14503 (participation of private school children), the Secretary will follow the procedures in section 14505(b). (Approved by the Office of Management and Budget under OMB control number... complaint procedures to parents of students, and appropriate private school officials or representatives...

Powertrain Test Procedure Development for EPA GHG Certification of Medium- and Heavy-Duty Engines and Vehicles

Energy Technology Data Exchange (ETDEWEB)

Chambon, Paul H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Deter, Dean D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2016-07-01

xiii ABSTRACT The goal of this project is to develop and evaluate powertrain test procedures that can accurately simulate real-world operating conditions, and to determine greenhouse gas (GHG) emissions of advanced medium- and heavy-duty engine and vehicle technologies. ORNL used their Vehicle System Integration Laboratory to evaluate test procedures on a stand-alone engine as well as two powertrains. Those components where subjected to various drive cycles and vehicle conditions to evaluate the validity of the results over a broad range of test conditions. Overall, more than 1000 tests were performed. The data are compiled and analyzed in this report.

ENRAF Series 854 Advanced Technology Gauge (ATG) with SPU II card for Leak Detector Use Acceptance Test Procedure

International Nuclear Information System (INIS)

SMITH, S.G.

1999-01-01

The following Acceptance Test Procedure was written to test the ENRAF series 854 ATG with SPU II card prior to installation in the Tank Farms. The procedure sets various parameters and verifies the gauge and alarms functionality

ENRAF Series 854 Advanced Technology Gauge (ATG) with SPU ll Card for Leak Detector Use Acceptance Test Procedure

International Nuclear Information System (INIS)

SMITH, S.G.

1999-01-01

The following Acceptance Test Procedure was written to test the Enraf Series 854 ATG with SPU-II card prior to installation in the Tank Farms. The procedure sets various parameters and verifies the gauge and the alarms functionality

Environmental protection and procedural law

International Nuclear Information System (INIS)

Mutschler, U.

1978-01-01

For the power industry which is 'independent of licensing', the Ule/Laubinger statement as well as its discussion on the 52th German legal experts' day are of considerable importance. It is therefore absolutely necessary to critically investigate the statements of this expert's opinion and the considerations on which they are based. This investigation is limited to those licensing procedures which in the terminology of experts, are 'similar to the plan approval procedure'. This applies mainly to the procedures according to paragraph 4 ff of the Federal Act on the Protection Against Nuisances and paragraph 7 of the Atomic Energy Law: Preliminaries publication of documents, inspection of files, public hearing, taking of evidence, persons with special responsibilities, administrative proceedings, actions by associations. The deficiencies in the execution of environmental procedural law is briefly mentioned. The notes in the article refer only to air pollution. (orig./HP) [de

A step-up test procedure to find the minimum effective dose.

Science.gov (United States)

Wang, Weizhen; Peng, Jianan

2015-01-01

It is of great interest to find the minimum effective dose (MED) in dose-response studies. A sequence of decreasing null hypotheses to find the MED is formulated under the assumption of nondecreasing dose response means. A step-up multiple test procedure that controls the familywise error rate (FWER) is constructed based on the maximum likelihood estimators for the monotone normal means. When the MED is equal to one, the proposed test is uniformly more powerful than Hsu and Berger's test (1999). Also, a simulation study shows a substantial power improvement for the proposed test over four competitors. Three R-codes are provided in Supplemental Materials for this article. Go to the publishers online edition of Journal of Biopharmaceutical Statistics to view the files.

77 FR 26607 - Energy Conservation Program: Test Procedures for Electric Motors and Small Electric Motors

Science.gov (United States)

2012-05-04

... Conservation Program: Test Procedures for Electric Motors and Small Electric Motors; Final Rules #0;#0;Federal... Procedures for Electric Motors and Small Electric Motors AGENCY: Office of Energy Efficiency and Renewable... electric motors and small electric motors. That supplemental proposal, along with an earlier proposal from...

Still special? Harvesting procedures for industrial hemp

Directory of Open Access Journals (Sweden)

Hans-Jörg Gusovius

2016-01-01

Full Text Available A multitude of different harvesting procedures is available after the re-approval of hemp growing in Germany about 20 years ago. Established, but as well recent machine developments enable the supply of raw materials for further processing or as food and feed materials. The necessary specialization level results in high but, compared to other established crops, not exceeding procedural costs. In this study, harvesting procedures and technologies are analyzed that are currently used under Northern European cultivation conditions. However, technological enhancements are still needed in order to improve the competitiveness of fibre hemp in the crop rotation as well as of hemp-based semi-finished and finished products.

Requirements for the approval of dosimetry services under the Ionising Radiations Regulations 1985: Pt. 3: Coordination and record-keeping

International Nuclear Information System (INIS)

1991-01-01

Guidance for dosimetry services on the requirements for approval by the Health and Safety Executive (HSE) is provided in three parts. This part sets out the procedures and criteria that will be used by HSE in the assessment of dosimetry services seeking approval for coordination and record keeping. (author)

Comparison of the combustion engine operating parameters and the ecological indicators of an urban bus in dynamic type approval tests and in actual operating conditions

Directory of Open Access Journals (Sweden)

Rymaniak Lukasz

2017-01-01

Full Text Available The article presents the considerations regarding a city bus combustion engine performanceparameters in dynamic type approval tests and in real operating conditions when servicing an urban bus line. A comparison of the designated engine operating time shares with respect to load and crankshaft rotational speed was made. The analysis included the ETC and WHTC tests, which showed significant discrepancies in the work areas of internal combustion engines in these test when compared to actual driving conditions. The details of the type approval tests used and the method of their denormalization for the drive unit were presented. The vehicle used for this research was an eighteen meter city bus equipped with a CI engine with a displacement of 9.2 dm3. The latest PEMS mobile equipment technology was used to conduct the road measurements. This allowed the emission indicators for CO, HC, NOx and PM to be determined, including specific emissions. The obtained values were then compared with the Euro V limits.The analysis of the test results was supplemented with the calculation of fuel consumption using the carbonbalance method.

Clean fog rapid procedure test of artificially and naturally polluted HVDC porcelain barrel insulators

International Nuclear Information System (INIS)

Vlastos, A.E.

1992-01-01

The first question asked in this paper refers to the variation of the peak leakage current prior to the flashover and the variation of the time prior to flashover in the test of artificially polluted insulators when using the up-and-down method. To answer this question sums up the test procedure used in the up-and-down method. For each trial represented the insulator was again polluted artificially and then dried following the procedure described in the paper. Then the insulator was transported into the fog chamber and the voltage and fog was switched on simultaneously. In these experiments a low fog injection rate was used

75 FR 8528 - Procedures for Transportation Workplace Drug and Alcohol Testing Programs

Science.gov (United States)

2010-02-25

... OST 2105-AD84 Procedures for Transportation Workplace Drug and Alcohol Testing Programs AGENCY: Office... of small entities, for purposes of the Regulatory Flexibility Act. The Department makes these... necessary for the Department to conduct a regulatory evaluation or Regulatory Flexibility Analysis for this...

Considerations for the selection of an applicable energy efficiency test procedure for electric motors in Malaysia: Lessons for other developing countries

International Nuclear Information System (INIS)

Yanti, P.A.A.; Mahlia, T.M.I.

2009-01-01

Electric motors are a major energy-consuming appliance in the industrial sector. According to a survey, electric motors account for more than 70% of the total growth from 1991 to 2004 in electricity consumption in this sector in Malaysia. To reduce electricity consumption, Malaysia should consider resetting the minimum energy efficiency standards for electric motors sometime in the coming year. The first step towards adopting energy efficiency standards is the creation of a procedure for testing and rating equipment. An energy test procedure is the technical foundation for all energy efficiency standards, energy labels and other related programs. The test conditions in the test procedure must represent the conditions of the country. This paper presents the process for the selection of an energy test procedure for electric motors in Malaysia based on the country's conditions and requirements. The adoption of test procedures for electric motors internationally by several countries is also discussed in this paper. Even though the paper only discusses the test procedure for electric motors in Malaysia, the methods can be directly applied in other countries without major modifications.

A P-value model for theoretical power analysis and its applications in multiple testing procedures

Directory of Open Access Journals (Sweden)

Fengqing Zhang

2016-10-01

Full Text Available Abstract Background Power analysis is a critical aspect of the design of experiments to detect an effect of a given size. When multiple hypotheses are tested simultaneously, multiplicity adjustments to p-values should be taken into account in power analysis. There are a limited number of studies on power analysis in multiple testing procedures. For some methods, the theoretical analysis is difficult and extensive numerical simulations are often needed, while other methods oversimplify the information under the alternative hypothesis. To this end, this paper aims to develop a new statistical model for power analysis in multiple testing procedures. Methods We propose a step-function-based p-value model under the alternative hypothesis, which is simple enough to perform power analysis without simulations, but not too simple to lose the information from the alternative hypothesis. The first step is to transform distributions of different test statistics (e.g., t, chi-square or F to distributions of corresponding p-values. We then use a step function to approximate each of the p-value’s distributions by matching the mean and variance. Lastly, the step-function-based p-value model can be used for theoretical power analysis. Results The proposed model is applied to problems in multiple testing procedures. We first show how the most powerful critical constants can be chosen using the step-function-based p-value model. Our model is then applied to the field of multiple testing procedures to explain the assumption of monotonicity of the critical constants. Lastly, we apply our model to a behavioral weight loss and maintenance study to select the optimal critical constants. Conclusions The proposed model is easy to implement and preserves the information from the alternative hypothesis.

40 CFR 63.8687 - What performance tests, design evaluations, and other procedures must I use?

Science.gov (United States)

2010-07-01

... evaluations, and other procedures must I use? 63.8687 Section 63.8687 Protection of Environment ENVIRONMENTAL... What performance tests, design evaluations, and other procedures must I use? (a) You must conduct each... run must last at least 1 hour. (e) You must use the following equations to determine compliance with...

40 CFR 63.7112 - What performance tests, design evaluations, and other procedures must I use?

Science.gov (United States)

2010-07-01

... evaluations, and other procedures must I use? 63.7112 Section 63.7112 Protection of Environment ENVIRONMENTAL..., design evaluations, and other procedures must I use? (a) You must conduct each performance test in Table... use wet dust suppression to control PM from PSH operations, a visible mist is sometimes generated by...

Material control test and evaluation system at the ICPP

International Nuclear Information System (INIS)

Johnson, C.E.

1979-01-01

The US DOE is evaluating process monitoring as part of a total nuclear material safeguards system. A monitoring system is being installed at the Idaho Chemical Processing Plant to test and evaluate material control and surveillance concepts in an operating nuclear fuel reprocessing plant. Process monitoring for nuclear material control complements conventional safeguards accountability and physical protection to assure adherence to approved safeguards procedures and verify containment of nuclear materials within the processing plant

42 CFR 8.28 - Expedited procedures for review of immediate suspension.

Science.gov (United States)

2010-10-01

... GENERAL PROVISIONS CERTIFICATION OF OPIOID TREATMENT PROGRAMS Procedures for Review of Suspension or Proposed Revocation of OTP Certification, and of Adverse Action Regarding Withdrawal of Approval of an...

17 CFR 202.11 - Public Company Accounting Oversight Board budget approval process.

Science.gov (United States)

2010-04-01

... 17 Commodity and Securities Exchanges 2 2010-04-01 2010-04-01 false Public Company Accounting Oversight Board budget approval process. 202.11 Section 202.11 Commodity and Securities Exchanges SECURITIES AND EXCHANGE COMMISSION INFORMAL AND OTHER PROCEDURES § 202.11 Public Company Accounting Oversight...

Phased Startup Initiative Phase 3 Test Procedure (OCRWM)

International Nuclear Information System (INIS)

PAJUNEN, A.L.

2000-01-01

The purpose of this test procedure is to safely operate the Fuel Retrieval System (FRS) and Integrated Water Treatment System (IWTS) with specific fuel canisters, and show that canisters containing fuel can be retrieved from the canister queue, decapped in the Canister Decapper, loaded into the Primary Clean Machine (PCM) for fuel cleaning, fuel sorted on the Process Table, then loaded back into fuel canisters and relocated in Basin Storage. Additional Data are collected during this test, beyond that collected during production operations. These data support qualifying the cleaning performance of the PCM, assessing the quantity of scrap generated during the cleaning, and evaluating the impact of fuel retrieval operations on the Basin water quality. The additional data collected primarily consist of weighing fuel and scrap at selected points in the operation, as well as photographing fuel and scrap as it is processed. The time to perform operations is also monitored for comparison with design predictions. Water quality data are collected to establish a base line to predict the effectiveness of equipment design for control of contamination and visibility during production operation

78 FR 68005 - Approval and Promulgation of Implementation Plans; Mississippi; Transportation Conformity SIP...

Science.gov (United States)

2013-11-13

...] Approval and Promulgation of Implementation Plans; Mississippi; Transportation Conformity SIP--Memorandum... transportation conformity criteria and procedures related to interagency consultation and enforceability of... conformity process to allow direct consultation among agencies at the Federal, state and local levels. This...

FDA-approved drugs that are spermatotoxic in animals and the utility of animal testing for human risk prediction.

Science.gov (United States)

Rayburn, Elizabeth R; Gao, Liang; Ding, Jiayi; Ding, Hongxia; Shao, Jun; Li, Haibo

2018-02-01

This study reviews FDA-approved drugs that negatively impact spermatozoa in animals, as well as how these findings reflect on observations in human male gametes. The FDA drug warning labels included in the DailyMed database and the peer-reviewed literature in the PubMed database were searched for information to identify single-ingredient, FDA-approved prescription drugs with spermatotoxic effects. A total of 235 unique, single-ingredient, FDA-approved drugs reported to be spermatotoxic in animals were identified in the drug labels. Forty-nine of these had documented negative effects on humans in either the drug label or literature, while 31 had no effect or a positive impact on human sperm. For the other 155 drugs that were spermatotoxic in animals, no human data was available. The current animal models are not very effective for predicting human spermatotoxicity, and there is limited information available about the impact of many drugs on human spermatozoa. New approaches should be designed that more accurately reflect the findings in men, including more studies on human sperm in vitro and studies using other systems (ex vivo tissue culture, xenograft models, in silico studies, etc.). In addition, the present data is often incomplete or reported in a manner that prevents interpretation of their clinical relevance. Changes should be made to the requirements for pre-clinical testing, drug surveillance, and the warning labels of drugs to ensure that the potential risks to human fertility are clearly indicated.

76 FR 25211 - Energy Conservation Program: Test Procedures for Fluorescent Lamp Ballasts

Science.gov (United States)

2011-05-04

...-government procurement policies that specify high efficiency ballasts. (CA IOUs, No. 19 at p. 2; NRDC, No. 21... luminous efficiency (BLE), which is measured directly using electrical measurements instead of the photometric measurements employed in the test procedure at Appendix Q. The calculation of BLE includes a...

Bureau of radiological health compliance testing procedures for cabinet S-ray systems

International Nuclear Information System (INIS)

Miller, E.A.; Sprau, D.

1976-01-01

A manual has been developed by the Bureau of Radiological Health of the Food and Drug Administration to establish procedures for the routine field testing of cabinet x-ray systems to determine compliance with the Federal Performance Standard for Cabinet X-Ray Systems, 21 CFR 1020.40. The manual provides specific instructions for testing each model of cabinet x-ray system. Results from the inspection are recorded on a data from which is designed to permit automatic data processing

49 CFR 40.247 - What procedures does the BAT or STT follow after a screening test result?

Science.gov (United States)

2010-10-01

... 49 Transportation 1 2010-10-01 2010-10-01 false What procedures does the BAT or STT follow after a... What procedures does the BAT or STT follow after a screening test result? (a) If the test result is an alcohol concentration of less than 0.02, as the BAT or STT, you must do the following: (1) Sign and date...

77 FR 8178 - Test Procedures for Central Air Conditioners and Heat Pumps: Public Meeting

Science.gov (United States)

2012-02-14

.... EERE-2010-BT-TP-0038] Test Procedures for Central Air Conditioners and Heat Pumps: Public Meeting... methodologies and gather comments on testing residential central air conditioners and heat pumps designed to use... residential central air conditioners and heat pumps that are single phase with rated cooling capacities less...

46 CFR 272.42 - Audit requirements and procedures.

Science.gov (United States)

2010-10-01

... procedures. (a) Required audit. In connection with the audit of the Operator's subsidizable expenses, the... of audit results. Upon completion of the audit by the Office of Inspector General, the MARAD Office of Financial Approvals shall notify the Operator of the audit results, including any items disallowed...

75 FR 8524 - Procedures for Transportation Workplace Drug and Alcohol Testing Programs

Science.gov (United States)

2010-02-25

... 2105-AD67 Procedures for Transportation Workplace Drug and Alcohol Testing Programs AGENCY: Office of... IFR to mitigate this conflict between the DOT rules and what we view as beneficial State laws by.... It merely eliminated a conflict that would have precluded parties from complying with certain State...

13 CFR 127.303 - How will SBA select and identify approved certifiers?

Science.gov (United States)

2010-01-01

... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false How will SBA select and identify approved certifiers? 127.303 Section 127.303 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION WOMEN-OWNED SMALL BUSINESS FEDERAL CONTRACT ASSISTANCE PROCEDURES Certification of EDWOSB or WOSB Status...

78 FR 16159 - Application Procedures and Criteria for Approval of Providers of a Personal Financial Management...

Science.gov (United States)

2013-03-14

... and Criteria for Approval of Providers of a Personal Financial Management Instructional Course by... personal financial management instructional course (``providers'') satisfy all prerequisites of the United... in an instructional course concerning personal financial management (``instructional course'' or...

Validation of the charm 3 SL3 beta-lactam test for screening raw milk in compliance with the U.S. pasteurized milk ordinance. Performance Tested Method 071002.

Science.gov (United States)

Salter, Robert S; Douglas, David; McRobbie, Lindsey; Quintana, Julio; Legg, David; Schwartz, Janine; Conaway, David; McPhee, Carla; Saul, Steven; Markovsky, Robert

2011-01-01

The Charm 3 SL3 beta-Lactam Test is a 3 min receptor-based lateral-flow Rapid One-Step Assay (ROSA) that detects the six beta-lactam drugs of concern approved for dairy cattle in the United States. The method is a biochemical formulation change of the SL3 beta-Lactam Test evaluated and approved in 2007. The Charm 3 SL3 was evaluated under the AOAC Research Institute Performance Tested Method (PTM) program following the protocol of the U.S. Food and Drug Administration, Center for Veterinary Medicine. The method was approved as PTM 071002 on May 8, 2009. The following drugs were detected in three combined lots: penicillin G at 3.8 ppb, ampicillin at 8.0 ppb, amoxicillin at 8.4 ppb, cephapirin at 20.0 ppb, ceftiofur (total metabolites) at 79 ppb, and cloxacillin at 8.6 ppb > or = 90% of the time with 95% confidence. These detection levels are lower than, but within 75% of, the U.S. Safe Level/Tolerances. Lot-to-lot repeatability was typically within 20% of these determined levels. The test kit was found to be suitable for testing thawed frozen samples. It was also found to respond with equal or better sensitivity to samples that contained incurred analytes, i.e., both the microbiologically active parent drug and its active metabolites. There were no interferences from somatic cells at 1.1 million/mL, bacterial cells at 300 000 CFU/mL, or 32 other non-beta-lactam drugs at 100 ppb. Ruggedness experiments indicated that the test procedure is robust. These results meet the fit-for-purpose approval criteria for inclusion in the National Conference for Interstate Milk Shipments milk testing program.

Miravalles Geothermal Project: Portable Well Flow Test Equipment and Procedures Manual

Energy Technology Data Exchange (ETDEWEB)

None

1980-05-01

The well flow test program has been designed to facilitate the gathering of information, with portable test equipment, from various wells with regard to their capability of flow, the quality of steam produced at various back pressures, the composition and quantity of noncondensable gases flashed from the wells and the composition and quantity of solids in the well's liquid streams (brine). The test program includes procedures for obtaining the following basic flow data pertinent to the plant power cycle design: (1) Effluent steam and brine flows, pressures and temperatures; (2) Noncondensable and dissolved gas contents in steam and brine; (3) H{sub s}S content in gases formed; and (4) Solids content and chemical analysis of steam and brine.

The Careful Puppet Master: Reducing risk and fortifying acceptance testing with Jenkins CI

Science.gov (United States)

Smith, Jason A.; Richman, Gabriel; DeStefano, John; Pryor, James; Rao, Tejas; Strecker-Kellogg, William; Wong, Tony

2015-12-01

Centralized configuration management, including the use of automation tools such as Puppet, can greatly increase provisioning speed and efficiency when configuring new systems or making changes to existing systems, reduce duplication of work, and improve automated processes. However, centralized management also brings with it a level of inherent risk: a single change in just one file can quickly be pushed out to thousands of computers and, if that change is not properly and thoroughly tested and contains an error, could result in catastrophic damage to many services, potentially bringing an entire computer facility offline. Change management procedures can—and should—be formalized in order to prevent such accidents. However, like the configuration management process itself, if such procedures are not automated, they can be difficult to enforce strictly. Therefore, to reduce the risk of merging potentially harmful changes into our production Puppet environment, we have created an automated testing system, which includes the Jenkins CI tool, to manage our Puppet testing process. This system includes the proposed changes and runs Puppet on a pool of dozens of RedHat Enterprise Virtualization (RHEV) virtual machines (VMs) that replicate most of our important production services for the purpose of testing. This paper describes our automated test system and how it hooks into our production approval process for automatic acceptance testing. All pending changes that have been pushed to production must pass this validation process before they can be approved and merged into production.

25 CFR 291.13 - When do Class III gaming procedures for an Indian tribe become effective?

Science.gov (United States)

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false When do Class III gaming procedures for an Indian tribe... ECONOMIC ENTERPRISES CLASS III GAMING PROCEDURES § 291.13 When do Class III gaming procedures for an Indian tribe become effective? Upon approval of Class III gaming procedures for the Indian tribe under either...

Test procedures and instructions for single shell tank saltcake cesium removal with crystalline silicotitanate

Energy Technology Data Exchange (ETDEWEB)

Duncan, J.B.

1997-01-07

This document provides specific test procedures and instructions to implement the test plan for the preparation and conduct of a cesium removal test, using Hanford Single Shell Tank Saltcake from tanks 24 t -BY- I 10, 24 1 -U- 108, 24 1 -U- 109, 24 1 -A- I 0 1, and 24 t - S-102, in a bench-scale column. The cesium sorbent to be tested is crystalline siticotitanate. The test plan for which this provides instructions is WHC-SD-RE-TP-024, Hanford Single Shell Tank Saltcake Cesium Removal Test Plan.

29 CFR 1928.53 - Protective enclosures for wheel-type agricultural tractors-test procedures and performance...

Science.gov (United States)

2010-07-01

... accomplished by using a 4,410-lb (2,000-kg) weight acting as a pendulum. The impact face of the weight shall be... the test; and (G) When any cables, props, or blocking shift or break during the test, the test shall... structure may be used to complete the test procedure; and (C) Impact at side. The blocking and restraining...

A test procedure for energetic and performance analysis of cold appliances for the food industry

International Nuclear Information System (INIS)

Armani, F; Boscolo, A

2013-01-01

In this article we present a novel approach for the characterization of cold appliances and in particular of refrigerators based on the standard vapour compression cycle with a reciprocating on/off compressor. The test procedure is based on a virtual instrument that perform both the stimulus and the data acquisition on the device under test. Acquired data is elaborated to fit a semi-empirical model based on the energetic balances between thermal and electrical sub systems and the heat exchanged with the environment. This approach results in a simple method to calculate useful parameters of the refrigerator, such as energetic performance, cooling effect and limit values of thermal loads. The test procedure requires only a few temperatures and the electric power consumption to be monitored, resulting in a low impact on the refrigerator. Preliminary tests showed a good estimation of parameters and prediction of energy consumption and heat extraction capacity of the refrigerator under test

Operatibility test procedure for the Waste Information and Control System

International Nuclear Information System (INIS)

Flynn, D.F.

1994-01-01

This document describes the operability test procedure for the WICS. The Westinghouse Hanford Company (WHC) Hazardous Material Control Group (HMC) of the 222-S Laboratory has requested the development of a system to help resolve many of the difficulties associated with tracking and data collection of containers and drums of waste. This system has been identified as Waste Information and Control System (WICS). The request for developing and implementing WICS has been made to the Automation and Simulation Engineering Group (ASE)

Comparison of IRT Likelihood Ratio Test and Logistic Regression DIF Detection Procedures

Science.gov (United States)

Atar, Burcu; Kamata, Akihito

2011-01-01

The Type I error rates and the power of IRT likelihood ratio test and cumulative logit ordinal logistic regression procedures in detecting differential item functioning (DIF) for polytomously scored items were investigated in this Monte Carlo simulation study. For this purpose, 54 simulation conditions (combinations of 3 sample sizes, 2 sample…