(Ternary liquid + liquid) equilibria for (water + acetone + α-pinene, or β-pinene, or limonene) mixtures

International Nuclear Information System (INIS)

Li Xiaoli; Tamura, Kazuhiro

2010-01-01

(Ternary liquid + liquid) equilibria (tie-lines) of (water + acetone + α-pinene) at T = (288.15, 298.15, and 308.15) K and (water + acetone + β-pinene, or limonene) at T = 298.15 K have been measured. The experimental (ternary liquid + liquid) equilibrium data have been correlated successfully by the original UNIQUAC and modified UNIQUAC models. The modified UNIQUAC model reproduced accurately the experimental results for the (water + acetone + α-pinene) system at all the temperatures but fairly agreed with the experimental data for the (water + acetone + β-pinene, or limonene) systems.

Experimental investigation of phase equilibria in the Nb-Si-Ta ternary system

Energy Technology Data Exchange (ETDEWEB)

Li, Jian; Wang, Cuiping; Yao, Jun; Yang, Shuiyuan; Zhan Shi; Liu, Xingjun [Xiamen Univ. (China). Dept. of Materials Science and Engineering; Xiamen Univ. (China). Fujian Provincial Key Laboratory of Materials Genome; Kang, Yongwang [Beijing Institute of Aeronautical Materials (China). Science and Technology on Advanced High Temperature Structural Materials Lab.

2016-12-15

The phase equilibria in the Nb-Si-Ta ternary system at 1 373 K, 1 473 K and 1 573 K were investigated by means of back-scattered electron imaging, electron probe microanalysis and X-ray diffraction. The isothermal sections at 1 373 K, 1 473 K and 1 573 K consist of two three-phase regions and seven two-phase regions, without any ternary compounds. The compounds of NbSi{sub 2} and TaSi{sub 2}, αNb{sub 5}Si{sub 3} and αTa{sub 5}Si{sub 3} form continuous solid solutions, respectively. The solubilities of Nb in Ta{sub 3}Si and Ta{sub 2}Si phases are extremely large, whereas the solubility of Si in the β(Nb, Ta) phase is relatively small.

Experimental determination of the phase equilibria in the Co-Fe-Zr ternary system

International Nuclear Information System (INIS)

Wang, C.P.; Yu, Y.; Zhang, H.H.; Hu, H.F.; Liu, X.J.

2011-01-01

Research highlights: → We determined four isothermal sections of the Co-Fe-Zr system from 1000 o C to 1300 o C. → No ternary compound was found in the Co-Fe-Zr ternary system. → The solubility of Fe in the liquid phase at 1300 o C is extremely large. → The (Co, Fe) 2 Zr phase form the continuous solution from Co-Zr side to Fe-Zr side. → The solubility of Zr in the fcc (Co, Fe) phase is extremely small. - Abstract: The phase equilibria in the Co-Fe-Zr ternary system were investigated by means of optical microscopy (OM), electron probe microanalysis (EPMA), X-ray diffraction (XRD), and differential scanning calorimetry (DSC) on equilibrated ternary alloys. Four isothermal sections of the Co-Fe-Zr ternary system at 1300 o C, 1200 o C, 1100 o C and 1000 o C were experimentally established. The experimental results indicate that (1) no ternary compound was found in this system; (2) the solubility of Fe in the liquid phase of the Co-rich corner at 1300 o C is extremely large; (3) the liquid phase in the Zr-rich corner and the (Co,Fe) 2 Zr phase form the continuous solid solutions from the Co-Zr side to the Fe-Zr side; (4) the solubility of Zr in the fcc (Co, Fe) phase is extremely small.

Phase equilibria of the Al-Pr-Zr ternary system at 773 K

Energy Technology Data Exchange (ETDEWEB)

She, Jia [Laboratory of Nonferrous Metal Materials and New Processing Technology, Ministry of Education, Guangxi University, Nanning, Guangxi 530004 (China); Zhan, Yongzhong, E-mail: zyzmatres@yahoo.com.c [Laboratory of Nonferrous Metal Materials and New Processing Technology, Ministry of Education, Guangxi University, Nanning, Guangxi 530004 (China); Li, Chunliu [Laboratory of Nonferrous Metal Materials and New Processing Technology, Ministry of Education, Guangxi University, Nanning, Guangxi 530004 (China); Du, Yong; Xu, Honghui; He, Yuehui [State Key Laboratory of Powder Metallurgy, Central South University, Changsha, Hunan 410083 (China)

2010-07-30

The phase equilibria of the Al-Pr-Zr ternary system at 773 K have been investigated mainly by means of X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and differential thermal analysis (DTA). The 14 binary compounds, i.e. AlZr{sub 3}, AlZr{sub 2}, Al{sub 2}Zr{sub 3}, Al{sub 3}Zr{sub 4}, AlZr, Al{sub 3}Zr{sub 2}, Al{sub 2}Zr, Al{sub 3}Zr, {alpha}-Al{sub 11}Pr{sub 3}, Al{sub 3}Pr, Al{sub 2}Pr, {beta}-AlPr, AlPr{sub 2} and {beta}-AlPr{sub 3} were confirmed. No binary compound was found in the Pr-Zr binary system. The result shows that the isothermal section of the Al-Pr-Zr ternary system at 773 K consists of 17 single-phase regions, 31 two-phase regions and 15 three-phase regions. All the intermediate compounds phases in this system have not a remarkable solid solution at 773 K. No ternary compound is found in this work.

Experimental investigation of phase equilibria in the Co-Ni-Zr ternary system

Energy Technology Data Exchange (ETDEWEB)

Liu, Xingjun; Yang, Shuiyuan; Yu, Wenjie; Wang, Cuiping [Xiamen Univ. (China). Fujian Key Laboratory of Materials Genome; Xiong, Huaping; Cheng, Yaoyong; Wu, Xin [Beijing Institute of Aeronautical Materials (China). Div. of Welding and Forging

2016-10-15

The phase equilibria of the Co-Ni-Zr ternary system at 1 000 C, 1 100 C and 1 200 C were experimentally investigated by means of back-scattered electron imaging, electron probe microanalysis and X-ray diffraction on the equilibrated ternary alloys. In this study, no ternary compound is found. The (αCo, Ni) phase region extends from the Ni-rich corner to the Co-rich corner with small solubility of Zr at three sections. At 1 000 C and 1 100 C, Ni{sub 5}Zr, Co{sub 2}Zr and Ni{sub 10}Zr{sub 7} phases have large solid solution ranges, but Ni{sub 10}Zr{sub 7} phase disappears at 1 200 C. The Ni{sub 7}Zr{sub 2}, NiZr, Co{sub 11}Zr{sub 2}, Co{sub 23}Zr{sub 6} and CoZr phases exhibit nearly linear compounds in the studied sections, and have large composition ranges. Additionally, some differences in phase relationship exist among the above three isothermal sections.

Experimental study of the phase equilibria in the Mg–Zn–Ag ternary system at 300 °C

Energy Technology Data Exchange (ETDEWEB)

Wang, Jian, E-mail: jian.wang@polymtl.ca [Center for Research in Computational Thermochemistry (CRCT), Department of Chemical Engineering, École Polytechnique, Montréal, Québec H3C 3A7 (Canada); Zhang, Yi-Nan [Department of Mechanical Engineering, Concordia University, 1455 De Maisonneuve Blvd. West, Montreal, Quebec H3G 1M8 (Canada); Hudon, Pierre; Jung, In-Ho [Department of Mining and Materials Engineering, McGill University, 3610 University Street, Montreal, Quebec H3A 0C5 (Canada); Medraj, Mamoun [Department of Mechanical Engineering, Concordia University, 1455 De Maisonneuve Blvd. West, Montreal, Quebec H3G 1M8 (Canada); Department of Mechanical and Materials Engineering, Masdar Institute, Masdar City, P.O. Box 54224, Abu Dhabi (United Arab Emirates); Chartrand, Patrice [Center for Research in Computational Thermochemistry (CRCT), Department of Chemical Engineering, École Polytechnique, Montréal, Québec H3C 3A7 (Canada)

2015-08-05

Highlights: • The phase equilibria of Mg–Zn–Ag system at 300 °C were determined. • A bcc continuous ternary solid solution forms between MgAg (bcc-B2) and AgZn (bcc-A2) was determined. • The extended solid solubilities of the sub-binary compounds were also determined. - Abstract: The phase equilibria in the Mg–Zn–Ag ternary system at 300 °C were investigated using three diffusion couples and 35 key samples. Scanning electron microscopy (SEM) equipped with energy-dispersive spectroscope (EDS) and X-ray diffraction (XRD) techniques were used for homogeneity ranges and crystal structure determination. Large solid solubility limits, due to substitution among Mg, Zn and Ag atoms in Mg{sub 3}Ag and MgZn{sub 2} phases, were observed in the present work. Solid solubility limits of Ag and Zn in the hcp (Mg) phase were found to be less than 1 at.%. The extended solid solubilities of the Mg{sub 12}Zn{sub 13}, Mg{sub 2}Zn{sub 3}, MgZn{sub 2} (C14), Mg{sub 2}Zn{sub 11}, Ag{sub 5}Zn{sub 8} and hcp (AgZn{sub 3}) sub-binary compounds were also determined in the Mg–Zn–Ag ternary system. In addition, a bcc continuous ternary solid solution forms between MgAg (bcc-B2) and AgZn (bcc-A2) at 300 °C.

Phase equilibria and critical phenomena in the cesium nitrate-water-diethylamine ternary system

International Nuclear Information System (INIS)

Il'in, K.K.; Kurskij, V.F.; Cherkasov, D.G.

2008-01-01

Phase equilibria and critical events in ternary cesium nitrate-water-diethylamine system, where border binary liquid system is characterized by aliquation with lower critical temperature of solution (LCTS), have been investigated by visual-polythermal method in the 60-150 Deg C range. Interaction of cesium nitrate in the water-diethylamine system leads to lowering of its LCTS from 146.1 to 69.3 Deg C and decrease of mutual solubility. Distribution ratios of diethylamine between water and organic phases of monotectic equilibrium are calculated at different temperatures. Diethylamine salting out from aqueous solutions by cesium nitrates becomes stronger with rising temperature. Plotted isotherms of phase confirms generalized scheme of topological transformations of ternary systems phase diagrams: salt-binary solvent with salting out

Phase equilibria in the ternary In-Ni-Sn system at 700 °C.

Science.gov (United States)

Schmetterer, C; Zemanova, A; Flandorfer, H; Kroupa, A; Ipser, H

2013-04-01

The phase equilibria of the ternary system In-Ni-Sn were investigated experimentally at 700 °C using X-ray diffraction (XRD) and scanning electron microscopy (SEM) including electron micro probe analysis (EMPA) and energy dispersive X-ray spectroscopy (EDX). A corresponding isothermal section was established based on these results. This particular temperature was chosen because it allowed obtaining reliable results within reasonable time. The existence of the ternary phase InNi 6 Sn 5 was confirmed whereas the ternary compound In 2 NiSn, reported earlier in literature, was found to be part of a large solid solution field based on binary InNi. The ternary solubility of the binary phases was established, and continuous solid solutions were found between the isostructural phases Ni 3 Sn LT and InNi 3 as well as between Ni 3 Sn 2 HT and InNi 2 . In addition, this isothermal section could be well reproduced by CALPHAD modelling. The resulting calculated isotherm at 700 °C is presented, too, and compared with the experimental results.

Prediction of phase equilibria and thermal analysis in the Bi-Cu-Pb ternary system

Energy Technology Data Exchange (ETDEWEB)

Manasijevic, Dragan [University of Belgrade, Technical Faculty, VJ 12, 19210 Bor (Serbia); Mitovski, Aleksandra, E-mail: amitovski@tf.bor.ac.rs [University of Belgrade, Technical Faculty, VJ 12, 19210 Bor (Serbia); Minic, Dusko [University of Pristina, Faculty of Technical Sciences, 38220 Kosovska Mitrovica (Serbia); Zivkovic, Dragana; Marjanovic, Sasa [University of Belgrade, Technical Faculty, VJ 12, 19210 Bor (Serbia); Todorovic, Radisa [Institute of Mining and Metallurgy, Zeleni Bulevar 35, 19210 Bor (Serbia); Balanovic, Ljubisa [University of Belgrade, Technical Faculty, VJ 12, 19210 Bor (Serbia)

2010-05-20

The knowledge about phase diagram of the Bi-Cu-Pb ternary system is of importance in development of copper-lead based bearing materials, soldering and in refining of copper and lead. In this work, the phase diagram of the Bi-Cu-Pb ternary system was calculated by the CALPHAD method using binary thermodynamic parameters included in the COST 531 database. The results include liquidus projection, invariant equilibria and three vertical sections with molar ratio Cu:Pb = 1, Cu:Pb = 1:3 and Bi:Cu = 1. Alloys, with compositions along three predicted vertical sections, were measured using differential scanning calorimetry (DSC). The experimentally determined phase transition temperatures were compared with calculated results and good mutual agreement was noticed.

Prediction of phase equilibria and thermal analysis in the Bi-Cu-Pb ternary system

International Nuclear Information System (INIS)

Manasijevic, Dragan; Mitovski, Aleksandra; Minic, Dusko; Zivkovic, Dragana; Marjanovic, Sasa; Todorovic, Radisa; Balanovic, Ljubisa

2010-01-01

The knowledge about phase diagram of the Bi-Cu-Pb ternary system is of importance in development of copper-lead based bearing materials, soldering and in refining of copper and lead. In this work, the phase diagram of the Bi-Cu-Pb ternary system was calculated by the CALPHAD method using binary thermodynamic parameters included in the COST 531 database. The results include liquidus projection, invariant equilibria and three vertical sections with molar ratio Cu:Pb = 1, Cu:Pb = 1:3 and Bi:Cu = 1. Alloys, with compositions along three predicted vertical sections, were measured using differential scanning calorimetry (DSC). The experimentally determined phase transition temperatures were compared with calculated results and good mutual agreement was noticed.

Phase Equilibria of the Sn-Ni-Si Ternary System and Interfacial Reactions in Sn-(Cu)/Ni-Si Couples

Science.gov (United States)

Fang, Gu; Chen, Chih-chi

2015-07-01

Interfacial reactions in Sn/Ni-4.5 wt.%Si and Sn-Cu/Ni-4.5 wt.%Si couples at 250°C, and Sn-Ni-Si ternary phase equilibria at 250°C were investigated in this study. Ni-Si alloys, which are nonmagnetic, can be regarded as a diffusion barrier layer material in flip chip packaging. Solder/Ni-4.5 wt.%Si interfacial reactions are crucial to the reliability of soldered joints. Phase equilibria information is essential for development of solder/Ni-Si materials. No ternary compound is present in the Sn-Ni-Si ternary system at 250°C. Extended solubility of Si in the phases Ni3Sn2 and Ni3Sn is 3.8 and 6.1 at.%, respectively. As more Si dissolves in these phases their lattice constants decrease. No noticeable ternary solubility is observed for the other intermetallics. Interfacial reactions in solder/Ni-4.5 wt.%Si are similar to those for solder/Ni. Si does not alter the reaction phases. No Si solubility in the reaction phases was detected, although rates of growth of the reaction phases were reduced. Because the alloy Ni-4.5 wt.%Si reacts more slowly with solders than pure Ni, the Ni-4.5 wt.%Si alloy could be a potential new diffusion barrier layer material for flip chip packaging.

Binary and ternary systems

International Nuclear Information System (INIS)

Petrov, D.A.

1986-01-01

Conditions for thermodynamical equilibrium in binary and ternary systems are considered. Main types of binary and ternary system phase diagrams are sequently constructed on the basis of general regularities on the character of transition from one equilibria to others. New statements on equilibrium line direction in the diagram triple points and their isothermal cross sections are developed. New represenations on equilibria in case of monovariant curve minimum and maximum on three-phase equilibrium formation in ternary system are introduced

Thermal analysis and prediction of phase equilibria in ternary Pb-Zn-Ag system

Directory of Open Access Journals (Sweden)

Živković D.

2011-01-01

Full Text Available Ternary Pb-Zn-Ag system is typical for some physicochemical processes going on in refining phase in the extractive metallurgy of lead. Therefore, investigation of mentioned system is important from both theoretical and practical research of the phenomena occurring during the lead desilverizing process. The results of experimental investigation using differential thermal analysis (DTA and thermodynamic calculation of phase equilibria in Pb-Zn-Ag system according to CALPHAD method, in the sections with Zn:Ag mass ratio equal to 90:10, 70:30 and 50:50, are presented in this paper.

Theoretical study of physical properties and oxygen incorporation effect in nanolaminated ternary carbides 211-MAX phases

KAUST Repository

Kanoun, Mohammed; Goumri-Said, Souraya

2012-01-01

In this chapter, we employ ab initio approaches to review some important physical properties of nanolaminated ternary carbides MAX phases. We fi rstly use an all electron full-potential linearized augmented plane-wave method within the generalized

Experimental measurements of vapor-liquid equilibria of the H2O + CO2 + CH4 ternary system

Science.gov (United States)

Qin, J.; Rosenbauer, R.J.; Duan, Zhenhao

2008-01-01

Reported are the experimental measurements on vapor-liquid equilibria in the H2O + CO2 + CH4 ternary system at temperatures from (324 to 375) K and pressures from (10 to 50) MPa. The results indicate that the CH4 solubility in the ternary mixture is about 10 % to 40 % more than that calculated by interpolation from the Henry's law constants of the binary system, H2O + CH4, and the solubility of CO2 is 6 % to 20 % more than what is calculated by the interpolation from the Henry's law constants of the binary mixture, H 2O + CO2. ?? 2008 American Chemical Society.

Experimental investigation of the phase equilibria in the Co-Fe-Ti ternary system

Energy Technology Data Exchange (ETDEWEB)

Yuan, Chaohui; Chen, Chong; Peng, Yingbiao; Du, Yong; Li, Kun [Central South Univ., State Key of Powder Metallurgy, Changsha (China); Lu, Xingxu [Central South Univ., State Key of Powder Metallurgy, Changsha (China); Central South Univ., School of Materials Science and Engineering, Changsha (China)

2015-08-15

Phase equilibria in the Co-Fe-Ti ternary system were investigated by means of the equilibrated alloy method with X-ray powder diffraction and electron probe microanalysis. No ternary compounds were found. The experimental results indicated the existence of seven two-phase and one three-phase regions at 600 C, five two-phase and two three-phase regions at 800 C, and six two-phase and two three-phase regions at 950 C. The solubility of Co in TiFe{sub 2} was determined to be larger than 54 at.% at all investigated temperatures, and the solubilities of Fe in TiCo{sub 3} and Ti{sub 2}Co showed an appreciable increase with increasing temperature. The three-phase equilibrium in the Ti-rich corner at 800 C was revealed to be ((β-Ti) + Ti(Fe, Co) + Ti{sub 2}Co) rather than ((α-Ti) + Ti(Fe, Co) + Ti{sub 2}Co) reported in previous investigations. Based on the experimental data obtained in the present work, three isothermal sections at 600, 800 and 950 C were established.

Solid-state phase equilibria in the Fe-Pt-Pr ternary system at 1173 K

International Nuclear Information System (INIS)

Ren Jing; Gu Zhengfei; Cheng Gang; Zhou Huaiying

2005-01-01

The solid-state phase equilibria in the Fe-Pt-Pr ternary system at 1173 K (Pr ≤ 70%) were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersion spectroscopy (EDS) techniques. The 1173 K isothermal section consists of 13 single-phase regions, 22 two-phase regions and 10 three-phase regions. At 1173 K, we have observed that the maximum solid solubility of Pt in α-Fe is below 1.5 at.% and the solid solution region of Pt in γ-Fe is from 2 to 35 at.%; the maximum solid solubility of Fe in Pt is 18 at.%. The maximum solubility of Fe in PrPt 5 , PrPt 3 , PrPt 2 , Pr 3 Pt 4 , PrPt, Pr 3 Pt 2 and Pr 7 Pt 3 is below 1 at.%. The maximum solubility of Pr in α-(Fe, Pt), γ-(Fe, Pt), FePt, FePt 3 and (Pt, Fe) (the solid solution of Fe in Pt) is 6, 2, 4, 4.5 and 1.5 at.%, respectively. In this work, it is found that the phase Pr 3 Pt 4 does not exist in the ternary system. The binary compounds Fe 7 Pr and Fe 2 Pr and any new ternary compounds were not observed

Ternary systems Sr-{Ni,Cu}-Si: Phase equilibria and crystal structure of ternary phases

International Nuclear Information System (INIS)

Nasir, Navida; Melnychenko-Koblyuk, Nataliya; Grytsiv, Andriy; Rogl, Peter; Giester, Gerald; Wosik, Jaroslaw; Nauer, Gerhard E.

2010-01-01

Phase relations were established in the Sr-poor part of the ternary systems Sr-Ni-Si (900 deg. C) and Sr-Cu-Si (800 deg. C) by light optical microscopy, electron probe microanalysis and X-ray diffraction on as cast and annealed alloys. Two new ternary compounds SrNiSi 3 (BaNiSn 3 -type) and SrNi 9-x Si 4+x (own-type) were found in the Sr-Ni-Si system along with previously reported Sr(Ni x Si 1-x ) 2 (AlB 2 -type). The crystal structure of SrNi 9-x Si 4+x (own-type, x=2.7, a=0.78998(3), c=1.1337(2) nm; space group P4/nbm) was determined from X-ray single crystal counter to be a low symmetry derivative of the cubic, parent NaZn 13 -type. At higher Si-content X-ray Rietveld refinements reveal the formation of a vacant site (□) corresponding to a formula SrNi 5.5 Si 6.5 □ 1.0 . Phase equilibria in the Sr-Cu-Si system are characterized by the compounds SrCu 2-x Si 2+x (ThCr 2 Si 2 -type), Sr(Cu x Si 1-x ) 2 (AlB 2 -type), SrCu 9-x Si 4+x (0≤x≤1.0; CeNi 8.5 Si 4.5 -type) and SrCu 13-x Si x (4≤x≤1.8; NaZn 13 -type). The latter two structure types appear within a continuous solid solution. Neither a type-I nor a type-IX clathrate compound was encountered in the Sr-{Cu,Ni}-Si systems. Structural details are furthermore given for about 14 new ternary compounds from related alloy systems with Ba. - Graphical abstract: The crystal structure of SrNi 9-x Si 4+x (own-type, x=2.7, a=0.78998(3), c=1.1337(2) nm; space group P4/nbm) was determined from X-ray single crystal counter to be a low symmetry derivative of the cubic, parent NaZn 13 -type and is related to CeNi 8.5 Si 4.5 -type.

Sc-W-Si and Sc-W-Ge ternary systems

International Nuclear Information System (INIS)

Kotur, B.Ya.; Voznyak, O.M.; Bodak, O.I.

1989-01-01

Phase equilibria in Sc-W-Si and Sc-W-Ge ternary systems are investigated at 1070 K. Sc 2+x W 3-x Si 4 ternary compound (0≤x≤1) is determined, its crystal structure (Ce 2 Sc 3 Si 4 structural type), as well as, change of elementary cell parameters and microhardness within homogeneity range are determined. Regularities of component interaction within Sc-M-Si(Ge) (M-Cr, Mo, W) ternary system are determined. Ternary systems with Mo and W are more closer to each other according to the phase equilibria character, than to ternary systems with Cr

Solid–liquid equilibria for binary and ternary systems with the Cubic-Plus-Association (CPA) equation of state

DEFF Research Database (Denmark)

Fettouhi, André; Thomsen, Kaj

2010-01-01

A systematic investigation of the CPA model's performance within solid-liquid equilibria (SLE) in binary mixtures (methane + ethane, methane + heptane, methane + benzene, methane + CO2, ethane + heptane, ethane + CO2, 1-propanol + 1,4-dioxane, ethanol + water, 2-propanol + water) is presented. Th....... The results from the binary mixtures are used to predict SLE behaviour in ternary mixtures (methane + ethane + heptane, methane + ethane + CO2). Our results are compared with experimental data found in the literature....

Ternary systems

International Nuclear Information System (INIS)

Kagan, D.N.; Hubberstey, P.; Barker, M.G.

1985-01-01

The paper reviews the experimental and theoretical studies carried out on multicomponent alkali metal systems. Solid-liquid phase equilibria studies are mainly concerned with the systems Na-K-Rb and Na-K-Cs, and data on the liquidus temperatures in these systems are presented. The thermodynamic properties of the ternary Na-K-Cs eutectic system have been determined experimentally, and the enthalpy, heat capacity and excess functions of the alloy are given. An analysis of calculational methods used in determining thermodynamic functions of ternary liquid metals systems is described. Finally, data are tabulated for the density, compressibility, saturated vapour pressure, viscosity and thermal conductivity of the ternary Na-K-Cs eutectic system. (UK)

Thermodynamic calculation on the stability of (Fe,Mn)3AlC carbide in high aluminum steels

International Nuclear Information System (INIS)

Chin, Kwang-Geun; Lee, Hyuk-Joong; Kwak, Jai-Hyun; Kang, Jung-Yoon; Lee, Byeong-Joo

2010-01-01

A CALPHAD type thermodynamic description for the Fe-Mn-Al-C quaternary system has been constructed by combining a newly assessed Mn-Al-C ternary description and a partly modified Fe-Al-C description to an existing thermodynamic database for steels. A special attention was paid to reproduce experimentally reported phase stability of κ carbide in high Al and high Mn steels. This paper demonstrates that the proposed thermodynamic description makes it possible to predict phase equilibria in corresponding alloys with a practically acceptable accuracy. The applicability of the thermodynamic calculation is also demonstrated for the interpretation of microstructural and constitutional evolution during industrial processes for high Al steels.

Direct phase coexistence molecular dynamics study of the phase equilibria of the ternary methane-carbon dioxide-water hydrate system.

Science.gov (United States)

Michalis, Vasileios K; Tsimpanogiannis, Ioannis N; Stubos, Athanassios K; Economou, Ioannis G

2016-09-14

Molecular dynamics simulation is used to predict the phase equilibrium conditions of a ternary hydrate system. In particular, the direct phase coexistence methodology is implemented for the determination of the three-phase coexistence temperature of the methane-carbon dioxide-water hydrate system at elevated pressures. The TIP4P/ice, TraPPE-UA and OPLS-UA forcefields for water, carbon dioxide and methane respectively are used, in line with our previous studies of the phase equilibria of the corresponding binary hydrate systems. The solubility in the aqueous phase of the guest molecules of the respective binary and ternary systems is examined under hydrate-forming conditions, providing insight into the predictive capability of the methodology as well as the combination of these forcefields to accurately describe the phase behavior of the ternary system. The three-phase coexistence temperature is calculated at 400, 1000 and 2000 bar for two compositions of the methane-carbon dioxide mixture. The predicted values are compared with available calculations with satisfactory agreement. An estimation is also provided for the fraction of the guest molecules in the mixed hydrate phase under the conditions examined.

Thermodynamic calculation on the stability of (Fe,Mn){sub 3}AlC carbide in high aluminum steels

Energy Technology Data Exchange (ETDEWEB)

Chin, Kwang-Geun [Automotive Steel Products Research Group, POSCO Technical Research Laboratories, POSCO, Jeonnam 545-090 (Korea, Republic of); School of Materials Science and Engineering, Pusan National University, Pusan, 609-735 (Korea, Republic of); Lee, Hyuk-Joong [Department of Materials Science and Engineering, Pohang University of Science and Technology (POSTECH), Pohang 790-784 (Korea, Republic of); Kwak, Jai-Hyun [Automotive Steel Products Research Group, POSCO Technical Research Laboratories, POSCO, Jeonnam 545-090 (Korea, Republic of); Kang, Jung-Yoon [School of Materials Science and Engineering, Pusan National University, Pusan, 609-735 (Korea, Republic of); Lee, Byeong-Joo, E-mail: calphad@postech.ac.k [Department of Materials Science and Engineering, Pohang University of Science and Technology (POSTECH), Pohang 790-784 (Korea, Republic of)

2010-08-27

A CALPHAD type thermodynamic description for the Fe-Mn-Al-C quaternary system has been constructed by combining a newly assessed Mn-Al-C ternary description and a partly modified Fe-Al-C description to an existing thermodynamic database for steels. A special attention was paid to reproduce experimentally reported phase stability of {kappa} carbide in high Al and high Mn steels. This paper demonstrates that the proposed thermodynamic description makes it possible to predict phase equilibria in corresponding alloys with a practically acceptable accuracy. The applicability of the thermodynamic calculation is also demonstrated for the interpretation of microstructural and constitutional evolution during industrial processes for high Al steels.

New investigation of phase equilibria in the system Al-Cu-Si.

Science.gov (United States)

Ponweiser, Norbert; Richter, Klaus W

2012-01-25

The phase equilibria and invariant reactions in the system Al-Cu-Si were investigated by a combination of optical microscopy, powder X-ray diffraction (XRD), differential thermal analysis (DTA) and electron probe micro analysis (EPMA). Isothermal phase equilibria were investigated within two isothermal sections. The isothermal section at 500 °C covers the whole ternary composition range and largely confirms the findings of previous phase diagram investigations. The isothermal section at 700 °C describes phase equilibria only in the complex Cu-rich part of the phase diagram. A new ternary compound τ was found in the region between (Al,Cu)-γ(1) and (Cu,Si)-γ and its solubility range was determined. The solubility of Al in κ-CuSi was found to be extremely high at 700 °C. In contrast, no ternary solubility in the β-phase of Cu-Al was found, although this phase is supposed to form a complete solid solution according to previous phase diagram assessments. Two isopleths, at 10 and 40 at.% Si, were investigated by means of DTA and a partial ternary reaction scheme (Scheil diagram) was constructed, based on the current work and the latest findings in the binary systems Al-Cu and Cu-Si. The current study shows that the high temperature equilibria in the Cu-rich corner are still poorly understood and additional studies in this area would be favorable.

Ternary and quaternary (liquid + liquid) equilibria for (water + ethanol + α-pinene, +β-pinene, or +limonene) and (water + ethanol + α-pinene + limonene) at the temperature 298.15 K

International Nuclear Information System (INIS)

Li Hengde; Tamura, Kazuhiro

2006-01-01

(Liquid + liquid) equilibria and tie-lines for the ternary (water + ethanol + α-pinene, or β-pinene or limonene) and quaternary (water + ethanol + α-pinene + limonene) mixtures have been measured at T = 298.15 K. The experimental multicomponent (liquid + liquid) equilibrium data have been successfully represented in terms of the modified UNIQUAC model with binary parameters

Equilibrium phase diagram of the Ag-Au-Pb ternary system

International Nuclear Information System (INIS)

Hassam, S.; Bahari, Z.

2005-01-01

The phase diagram of the ternary system Ag-Au-Pb has been established using differential thermal analysis and X-ray powder diffraction analysis. Four vertical sections were studied: X Pb = 0.40, X Au /X Pb = 1/3, X Ag /X Au = 4/1 and X Ag /X Au = 1/1. Two ternary transitory peritectics and one ternary eutectic were characterized. A schematic representation of the ternary equilibria is given

(Liquid + liquid) equilibria for (water + 1-propanol or acetone + β-citronellol) at different temperatures

International Nuclear Information System (INIS)

Li, Hengde; Han, Yongtao; Huang, Cheng; Yang, Chufen

2015-01-01

Graphical abstract: (Liquid + liquid) equilibrium data for systems composed of β-citronellol and aqueous 1-propanol or acetone are presented. Distribution ratios of 1-propanol and acetone in the mixtures are examined. The effect of the temperature on the ternary (liquid + liquid) equilibria is evaluated and discussed. - Highlights: • Ternary (liquid + liquid) equilibria containing β-citronellol are presented. • Distribution ratios of 1-propanol and acetone in the mixtures are examined. • The effect on the temperature of the systems is evaluated and discussed. - Abstract: On this paper, experimental (liquid + liquid) equilibrium (LLE) results are presented for systems composed of β-citronellol and aqueous 1-propanol or acetone. To evaluate the phase separation properties of β-citronellol in aqueous mixtures, LLE values for the ternary systems (water + 1-propanol + β-citronellol) and (water + acetone + β-citronellol) were determined with a tie-line method at T = (283.15, 298.15, and 313.15 ± 0.02) K and atmospheric pressure. The reliability of the experimental tie-lines was verified by the Hand and Bachman equations. Ternary phase diagrams, distribution ratios of 1-propanol and acetone in the mixtures are shown. The effect of the temperature on the ternary (liquid + liquid) equilibria was examined and discussed. The experimental LLE values were satisfactorily correlated by extended UNIQUAC and modified UNIQUAC models

Constitution of the ternary system Cr–Ni–Ti

International Nuclear Information System (INIS)

Krendelsberger, Natalja; Weitzer, Franz; Du, Yong; Schuster, Julius C.

2013-01-01

Highlights: •Reaction scheme and liquidus surface for Cr-Ni-Ti are given. •In the ternary the C14-type Laves phase coexists with the liquid phase. •Two ternary eutectics are identified. -- Abstract: The nature of solid–liquid phase equilibria in the ternary system Cr–Ni–Ti was investigated using electron microscopy, energy dispersive spectroscopy, X-ray diffraction, and differential thermal analysis. Literature data on solid state phase equilibria are confirmed. The Cr 2 Ti Laves phase modifications coexisting with Ni–Ti phases are clarified to be hexagonal C14-type and cubic C15-type. The C14-type Laves phase γCr 2 Ti is found to coexist with the liquid phase. It forms in the pseudobinary peritectic reaction p max1 from L + β(Cr,Ti) at 1389 °C. On further cooling γCr 2 Ti + NiTi solidify at 1202 °C in the pseudobinary eutectic e max2 . In the Cr-rich part of the system ternary eutectics occur at 1216 °C (E 1 : L = Ni 3 Ti + (Ni) + β(Cr,Ti)) and 1100 °C (E 2 : L = NiTi + Ni 3 Ti + β(Cr,Ti)), respectively. No ternary eutectic is found in the Ti-rich part. Rather the eutectic trough ends in the binary eutectic L = NiTi 2 + β(Ti)

The ternary system nickel-nobium-carbon

International Nuclear Information System (INIS)

Stadelmaier, H.H.; Fiedler, M.L.

1975-01-01

The ternary system nickel-niobium-carbon was studied by metallographic and X-ray diffraction methods to produce a liquidus projection and an isothermal section at 1,100 0 C. The liquidus projection is dominated by a wide field of primary NbC that extends far into the nickel corner of the composition triangle. Only one ternary compound is observed in this system, an eta-carbide formed in a peritectoid reaction. It has a narrow homogeneity range at Ni 2 Nb 4 C, and its lattice constant in alloys quenched from 1,100 0 C varies between 11.659 and 11.667 A. No eta-carbide Ni 3 Nb 3 C or Ni 6 Nb 6 could be detected. (orig.) [de

Mechanically activated synthesis of nanocrystalline ternary carbide Fe3Mo3C

International Nuclear Information System (INIS)

Zakeri, M.; Rahimipour, M.R.; Khanmohammadian, A.

2008-01-01

In this investigation, Fe 3 Mo 3 C ternary carbide was synthesized from the elemental powders of 3Mo/3Fe/C by mechanical milling and subsequent heat treatment. Structural and morphological evolutions of powders were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Results showed that no phase transformation occurs during milling. A nanostructure Mo (Fe) solid solution obtained after 30 h of milling. With increasing milling time to 70 h no change takes place except grain size reduction to 9 nm and strain enhancement to 0.86%. Milled powders have spheroid shape and very narrow size distribution about 2 μm at the end of milling. Fe 3 Mo 3 C was synthesized during annealing of 70 h milled sample at 700 deg. C. Undesired phases of MoOC and Fe 2 C form at 1100 deg. C. No transformation takes place during annealing of 10 h milled sample at 700 deg. C. Mean grain size and strain get to 69 nm and 0.23% respectively with annealing of 70 h milled sample at 1100 deg. C

Equilibria in aqueous cadmium-chloroacetate-glycinate systems. A convolution-deconvolution cyclic voltammetric study

International Nuclear Information System (INIS)

Abdel-Hamid, R.; Rabia, M.K.M.

1994-01-01

Stability constants and composition of cadmium-glycinate binary complexes were determined using cyclic voltammetry. Furthermore, binary and ternary complex equilibria for chloroacetates and glycinate with cadmium in 0.1 M aqueous KNO 3 at pH 10.4 and 298 K were investigated. Cadmium forms binary complexes with chloroacetates of low stability and ternary ones with chloroacetate-glycinate of significant stability. (author)

Equilibrium studies of ternary systems containing some selected transition metal ions, triazoles and aromatic carboxylic acids

Energy Technology Data Exchange (ETDEWEB)

Khalil, Mohamed Magdy; Radalla, Abd-Elatty; Qasem, Fatma; Khaled, Rehab [Beni-Suef University, Beni-Suef (Egypt)

2014-01-15

Solution equilibria of the binary and ternary complex systems of the divalent transition metal ions Cu{sup 2+}, Ni{sup 2+}, Zn{sup 2+}, and Co{sup 2+} with 1,2,4-triazole (TRZ), 3-mercapto-1,2,4-triazole (TRZSH), and 3-amino-1,2,4-triazole (TRZAM) and aromatic carboxylic acids (phthalic, anthranilic, salicylic, and 5-sulfosalicylic acid) have been studied pH-metrically at (25.0±0.1) .deg. C, and a constant ionic strength I=1x10{sup -1} mol L{sup -1} NaNO{sub 3} in an aqueous medium. The potentiometric titration curves show that binary and ternary complexes of these ligands are formed in solution. The stability constants of the different binary and ternary complexes formed were calculated on the basis of computer analysis of the titration data. The relative stability of the different ternary complex species is expressed in terms of Δ log K values, log X and R. S.% parameters. The effect of temperature of the medium on both the proton-ligand equilibria for TRZAM and phthalic acid and their metal-ligand equilibria with Cu{sup 2+}, Ni{sup 2+}, and Co{sup 2+} has been studied along with the corresponding thermodynamic parameters. The complexation behavior of ternary complexes is ascertained using conductivity measurements. In addition, the formation of ternary complexes in solution has been confirmed by using UV-visible spectrophotometry.

High-pressure (vapour + liquid) equilibria for ternary systems composed by {(E)-2-hexenal or hexanal + carbon dioxide + water}: Partition coefficient measurement

International Nuclear Information System (INIS)

Bejarano, Arturo; López, Pablo I.; Valle, José M. del; Fuente, Juan C. de la

2015-01-01

Highlights: • A new apparatus based on a static–analytic method was assembled in this work. • This work reports high-pressure VLE data of (E)-2-hexenal or hexanal + CO 2 + water. • Data includes (CO 2 + water) partition coefficients of (E)-2-hexenal and hexanal. • High separation factors from water (∼10 4 ) were found especially for (E)-2-hexenal. • The data were obtained at T = (313, 323, and 333) K and pressures from (8 to 19) MPa. - Abstract: A new apparatus based on a static–analytic method assembled in this work was utilised to perform high-pressure (vapour + liquid) equilibria measurements of aqueous ternary systems. This work includes values of isothermal partition coefficients between CO 2 and water of two apple aroma constituents, (E)-2-hexenal and hexanal. Additionally, this work reports new experimental (vapour + liquid) equilibria measurements for the ternary systems (CO 2 + (E)-2-hexenal + water) and (CO 2 + hexanal + water), at fixed liquid phase composition (600 mg · kg −1 ), at temperatures of (313, 323 and 333) K and at pressures from (8 to 19) MPa. Vapour liquid interphase was checked and monitored visually for all the systems studied in this work. No liquid immiscibility was observed at the composition, temperatures and pressures studied. In order to suggest reasonable operation conditions for fractionation of aromas with dense carbon dioxide, partition coefficients of the aroma compounds between CO 2 and water along with their separation factors from water were calculated. Partition coefficients of (E)-2-hexenal between CO 2 and water were in the range of (6 to 91) and where found to be near six times higher than those of hexanal (9 to 17). Very high separation factors from water were observed (∼10 4 ) especially for (E)-2-hexenal. The highest separation factor, for both compounds, was found at a temperature of 313 K and pressures from (12 to 14) MPa

First principles calculation of L21+A2 coherent equilibria in the Fe-Al-Ti system

International Nuclear Information System (INIS)

Alonso, Paula R.; Gargano, Pablo H.; Ramirez-Caballero, Gustavo E.; Balbuena, Perla B.; Rubiolo, Gerardo H.

2009-01-01

By combining first-principles density functional total energy calculations and statistical mechanics the ground state and the phase equilibria at finite temperatures of the ternary system Fe-Al-Ti have been investigated. Total energy calculations have been performed by means of the Wien 2k code to establish the ground state energetic. A cluster expansion method was therewith used to describe solid solutions. At several chosen finite temperatures the cluster variation method in the irregular tetrahedron approximation was employed in order to calculate the iron rich ternary bcc equilibria. It is confirmed that there are two kinds of phase separations of the bcc phase, A2+L2 1 and B2+L2 1 .

Influence of the temperature on the (liquid + liquid) phase equilibria of (water + 1-propanl + linalool or geraniol)

International Nuclear Information System (INIS)

Wan, Li; Li, Hengde; Huang, Cheng; Feng, Yuqing; Chu, Guoqiang; Zheng, Yuying; Tan, Wei; Qin, Yanlin; Sun, Dalei; Fang, Yanxiong

2017-01-01

Highlights: • Ternary LLEs containing linalool and geraniol are presented. • Distribution ratios of 1-propanol in the mixtures are examined. • Influence of the temperature on the LLE is studied. • The LLE data were correlated using the NRTL and UNIQUAC models. - Abstract: Linalool and geraniol are the primary components of rose oil, palmarosa oil, and citronella oil and many other essential oils, and two important compounds used in the flavour and fragrance, cosmetic or pharmaceutical industries. Phase equilibria (LLE, VLE, solubility, etc.) and related thermodynamic properties of a mixture are essential in the processes design and control of mass transfer process. In this work, experimental (liquid + liquid) equilibria data of the systems (water + 1-propanl + linalool) and (water + 1-propanl + geraniol) are presented. The (liquid + liquid) equilibria of both systems were determined with a tie-line method at T = (283.15, 298.15 and 313.15) K under atmospheric pressure. The well-known Hand, Bachman and Othmer–Tobias equations were used to test the reliability of the experimental values. The influence of the temperature on the (liquid + liquid) phase equilibria of the mixtures, the binodal curves and distribution ratios of 1-propanl are shown and discussed. Moreover, the NRTL and UNIQUAC models were applied to fit the data for both ternary systems. The interaction parameters obtained from both models successfully correlated the equilibrium compositions. Furthermore, the ternary systems could be represented using the binary parameters of the thermodynamic model with a function of temperature.

Constitutional studies of the molybdenum-ruthenium-palladium ternary system

International Nuclear Information System (INIS)

Cornish, L.A.; Pratt, J.N.

1997-01-01

An experimental and computational study has been made of phase equilibria in the Mo-Ru-Pd ternary system. The constitution of annealed binary and ternary alloys was investigated using optical and electron microscopy, X-ray diffraction and SEM phase analysis techniques. Limited thermodynamic measurements were made using the ZrO 2 solid electrolyte e.m.f. method. The data obtained from the various techniques were used to construct a ternary isothermal section at 1473 K. The experimentally determined section is compared with a calculated section for the same temperature, computed using thermodynamic coefficients derived solely from binary system information. Lattice parameters are reported for the b.c.c., f.c.c. and c.p.h. solid solutions and for the σ phase. (orig.)

Calculation of Fe–B–V ternary phase diagram

International Nuclear Information System (INIS)

Homolová, Viera; Kroupa, Aleš; Výrostková, Anna

2012-01-01

Highlights: ► Phase diagram of Fe–B–V system was modelled by CALPHAD method. ► Database for thermodynamic calculations for Fe–B–V system was created. ► The new ternary phase was found in 67Fe–18B–15V [in at.%] alloy. - Abstract: The phase equilibria of the Fe–B–V ternary system are studied experimentally and theoretically in this paper. Phase diagram of the system was modelled by CALPHAD method. Boron was modelled as an interstitial element in the FCC and BCC solid solutions. The calculations of isothermal sections of phase diagram are compared with our experimental results at 903 and 1353 K and with available literature experimental data. New ternary phase (with chemical composition 28Fe32V40B in at.%) was found in 67Fe–18B–15V alloy [in at.%]. Further experimental studies for the determination of exact nature of the ternary phase including crystallographic information are necessary.

The ternary system Zr-Cr-O. Equilibrium diagrams in the zirconium rich zone at different temperatures

International Nuclear Information System (INIS)

Gonzalez, Ruben O.; Gribaudo, Luis M.

2003-01-01

Equilibria among hcp α, bcc β solid solutions and cubic C 15 type intermetallic ZrCr 2 are represented graphically over Gibbs triangles in the Zr-rich zone of the ternary Zr-Cr-O system. Experimental results are obtained from zirconium-based alloys containing different oxygen compositions (0,24 and 0,62 % at.). Phase boundaries of the ternary system are extrapolated to the Zr-O and Zr-Cr binaries. The obtained values are compared to recently published evaluated diagrams of these two systems. Chromium compositions of the studied alloys were 0,3 - 1 - 2 - 4 and 15 at. %. Thermal treatment temperatures in order to allow equilibria in alloys were 840, 860, 900 and 960 C degrees. (author)

Mechanically activated synthesis of nanocrystalline ternary carbide Fe{sub 3}Mo{sub 3}C

Energy Technology Data Exchange (ETDEWEB)

Zakeri, M. [Materials Science Department, Islamic Azad University (Saveh branch), Saveh (Iran, Islamic Republic of)], E-mail: M_zakeri@iau-saveh.ac.ir; Rahimipour, M.R. [Ceramic Department, Materials and Energy Research Center, Tehran (Iran, Islamic Republic of); Khanmohammadian, A. [Materials Science Department, Islamic Azad University (Saveh branch), Saveh (Iran, Islamic Republic of)

2008-09-25

In this investigation, Fe{sub 3}Mo{sub 3}C ternary carbide was synthesized from the elemental powders of 3Mo/3Fe/C by mechanical milling and subsequent heat treatment. Structural and morphological evolutions of powders were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Results showed that no phase transformation occurs during milling. A nanostructure Mo (Fe) solid solution obtained after 30 h of milling. With increasing milling time to 70 h no change takes place except grain size reduction to 9 nm and strain enhancement to 0.86%. Milled powders have spheroid shape and very narrow size distribution about 2 {mu}m at the end of milling. Fe{sub 3}Mo{sub 3}C was synthesized during annealing of 70 h milled sample at 700 deg. C. Undesired phases of MoOC and Fe{sub 2}C form at 1100 deg. C. No transformation takes place during annealing of 10 h milled sample at 700 deg. C. Mean grain size and strain get to 69 nm and 0.23% respectively with annealing of 70 h milled sample at 1100 deg. C.

Comparison of two association models (Elliott-Suresh-Donohue and simplified PC-SAFT) for complex phase equilibria of hydrocarbon-water and amine-containing mixtures

DEFF Research Database (Denmark)

Grenner, Andreas; Schmelzer, Jürgen; von Solms, Nicolas

2006-01-01

, and water. Furthermore, the predictive capabilities of the models are investigated for four ternary systems composed of these components, which exhibit complex liquid-liquid(-liquid) equilibria (LLLE). Various aspects of association models which have an influence in the results are studied for the PC......, both models perform overall similarly for the binary systems, although ESD shows a remarkably good behavior despite its simplicity and the use of only the two-site scheme for all associating compounds. The prediction of the LLE in the ternary systems water + octane + aniline and water + CHA + aniline......Two Wertheim-based association models, the simplified PC-SAFT and the Elliott-Suresh-Donohue (ESD) equation of state, are compared in this work for the description of vapor-liquid equilibria (VLE) and liquid-liquid equilibria (LLE) in binary systems of aniline, cyclohexylamine (CHA), hydrocarbons...

Thermodynamic calculation of Al-Gd and Al-Gd-Mg phase equilibria checked by key experiments

International Nuclear Information System (INIS)

Groebner, J.; Kevorkov, D.; Schmid-Fetzer, R.

2001-01-01

The binary Al-Gd and the ternary Al-Gd-Mg systems were calculated using the Calphad method. It is demonstrated that previous interpretation of ternary liquidus temperatures below 700 C must be related to other phase equilibria. The actual ternary liquidus temperatures are much higher, up to some 600 C above the previous interpretation in literature. They are widely governed by the high-melting compounds Al 2 Gd and Al 3 Gd with liquidus surfaces stretching far into the ternary system. A small number of key experiments in this work confirmed the calculated liquidus temperature and the phase relations. The available experimental data in literature fit excellently with the calculation in the binary Al-Gd system. In the ternary Al-Gd-Mg system, which is shown in several sections of the phase diagram, a good agreement can be observed too, considering the necessary reinterpretation of the liquidus temperatures suggested by Rokhlin et al. Ternary solubilities were not found experimentally. The ternary compound Al 4 GdMg (τ) forms in a ternary peritectic reaction at 761 C. (orig.)

Theoretical study of physical properties and oxygen incorporation effect in nanolaminated ternary carbides 211-MAX phases

KAUST Repository

Kanoun, Mohammed

2012-01-01

In this chapter, we employ ab initio approaches to review some important physical properties of nanolaminated ternary carbides MAX phases. We fi rstly use an all electron full-potential linearized augmented plane-wave method within the generalized gradient approximation and the density functional theory approaches, to explore the existence of a steric effect on the M site in these compounds. The elastic properties are also reported in order to assess the mechanical stability. The substitution of oxygen for carbon in Ti 2 SnC M n +1 AX n, forming Ti 2 SnC 1- x O x, is examined next, where we simulated the effect of oxygen incorporation on mechanical and electronic properties using projector augmented wave method. We show that oxygen has interesting effects on both of elastic and electronic properties, that the bulk modulus decreases when oxygen concentration increases. The bonding in Ti 2 SnC 1- x O x has a tendency to a covalent-ionic nature with the presence of metallic character. © 2012 Woodhead Publishing Limited.

A ternary logic model for recurrent neuromime networks with delay.

Science.gov (United States)

Hangartner, R D; Cull, P

1995-07-01

In contrast to popular recurrent artificial neural network (RANN) models, biological neural networks have unsymmetric structures and incorporate significant delays as a result of axonal propagation. Consequently, biologically inspired neural network models are more accurately described by nonlinear differential-delay equations rather than nonlinear ordinary differential equations (ODEs), and the standard techniques for studying the dynamics of RANNs are wholly inadequate for these models. This paper develops a ternary-logic based method for analyzing these networks. Key to the technique is the realization that a nonzero delay produces a bounded stability region. This result significantly simplifies the construction of sufficient conditions for characterizing the network equilibria. If the network gain is large enough, each equilibrium can be classified as either asymptotically stable or unstable. To illustrate the analysis technique, the swim central pattern generator (CPG) of the sea slug Tritonia diomedea is examined. For wide range of reasonable parameter values, the ternary analysis shows that none of the network equilibria are stable, and thus the network must oscillate. The results show that complex synaptic dynamics are not necessary for pattern generation.

Liquid-liquid equilibria for binary and ternary polymer solutions with PC-SAFT

DEFF Research Database (Denmark)

Lindvig, Thomas; Michelsen, Michael Locht; Kontogeorgis, Georgios

2004-01-01

concentration coexistence curves at fixed pressure and temperature. The algorithms automatically trace the entire liquid-liquid coexistence curves in steps by adjusting the step size, generating initial estimates, and subsequently solving the phase-equilibrium problem by a second-order method. The algorithms...... are used for investigating the correlative and predictive capabilities of the thermodynamic model PC-SAFT. The investigation shows that the model correlates well experimental LLE data for binary as well as ternary systems but further predicts the behavior of the ternary systems with reasonably good...

Phase equilibria, phases and compounds in the Ti-C system

International Nuclear Information System (INIS)

Gusev, Aleksandr I

2002-01-01

The results of experimental and theoretical investigations of the phase equilibria in the titanium-carbon system are generalised. The generalised thermodynamic characteristics of disordered titanium carbide TiC y , are reported. Peculiarities of the crystal structures of all the known and hypothetical compounds of titanium with carbon are considered in detail. The X-ray diffraction patterns which allow identification of all these compounds are presented. The phase diagrams of the Ti-C system constructed with allowance for atomic ordering of non-stoichio metric carbide, TiC y , and for the existence of the molecular cluster-like compounds Ti 8 C 12 and Ti 13 C 22 (TiC 2 ) are discussed. The bibliography includes 142 references.

Phase equilibria, phases and compounds in the Ti-C system

International Nuclear Information System (INIS)

Gusev, A.I.

2002-01-01

The results of experimental and theoretical investigations related to the phase equilibria in the titanium-carbon system are generalized. The generalized thermodynamic characteristics of the disordered titanium carbide TiC y are given. The crystal structure of all the discovered and hypothetical compounds of titanium with carbon are considered in detail. The x-ray diffraction patterns which allow one to identify all these compounds are given. The phase diagrams of the Ti-C system constructed with allowance for atomic ordering of non-stoichiometric TiC y carbide and for the existence of the compounds Ti 8 C 12 and Ti 13 C 22 (TiC 2 ) of the molecule cluster type are discussed [ru

Prediction of phase equilibria in the In–Sb–Pb system

Directory of Open Access Journals (Sweden)

DUSKO MINIC

2008-03-01

Full Text Available Binary thermodynamic data, successfully used for phase diagram calculations of the binary systems In–Sb, Pb–Sb and In–Pb, were used for the prediction of the phase equilibria in the ternary In–Sb–Pb system. The predicted equilibrium phase diagram of the vertical Pb–InSb section was compared with the results of differential thermal analysis DTA and optical microscopy. The calculated phase diagram of the isothermal section at 300 °C was compared with the experimentally (SEM, EDX determined composition of phases in the chosen alloys after annealing. Very good agreement between the binary-based thermodynamic prediction and the experimental data was found in all cases. The calculated liquidus projection of the ternary In–Sb–Pb system is also presented.

Phase transitions on (liquid + liquid) equilibria for (water + 1-methylnaphthalene + light aromatic hydrocarbon) ternary systems at T = (563, 573, and 583) K

International Nuclear Information System (INIS)

Togo, Masaki; Inamori, Yoshiki; Shimoyama, Yusuke

2012-01-01

Highlights: ► Mixtures of (water + 1-methylnaphthalene + light aromatic hydrocarbon) are focused. ► Phase transition pressures on (liquid + liquid) equilibria were measured. ► Effects of aromatic hydrocarbons on phase transition pressure are investigated. ► Phase transition pressures are discussed using dielectric constants of hydrocarbons. - Abstract: Phase transitions for (water + 1-methylnaphthalene + light aromatic hydrocarbon) ternary systems are observed at their (liquid + liquid) equilibria at T = (563, 573, and 583) K and (8.6 to 25.0) MPa. The phase transition pressures at T = (563, 573, and 583) K were measured for the five species of light aromatic hydrocarbons, o-, m-, p-xylenes, ethylbenzene, and mesitylene. The measurements of the phase transition pressures were carried out by changing the feed mole fraction of water and 1-methylnaphthalene in water free, respectively. Effects of the feed mole fraction of water on the phase transition pressures are very small. Increasing the feed mole fraction of 1-methylnaphthalene results in decreasing the phase transition pressures at constant temperature. The slopes depending on the feed mole fraction for 1-methylnaphthalene at the phase transition pressures are decreased with increasing temperature for (water + 1-methylnaphthalene + p-xylene), (water + 1-methylnaphthalene + o-xylene), and (water + 1-methylnaphthalene + mesitylene) systems. For xylene isomers, the highest and lowest of the phase transition pressures are obtained in the case of p- and o-xylenes, respectively. The phase transition pressures for ethylbenzene are lower than those in the case of p-xylene. The similar phase transition pressures are given for p-xylene and mesitylene.

Investigation of the Na2(H2PO2)2 - Ba(H2PO2)2 - H2O Water-Salt Ternary System at Room Temperature

OpenAIRE

Erge, Hasan; Turan, Hakan; Kul, Ali Riza

2016-01-01

Objective: In this study, the solubility, density, conductivity and phase equilibria of the Na2(H2PO2)2-Ba(H2PO2)2-H2O ternary system located in the structure of the Na+, Ba2+, (H2PO2)-//H2O quaternary reciprocal water-salt system were investigated using physicochemical analysis methods. Material and Methods: Riedel-de Haen and Merck salts were used to investigate the solubility and phase equilibria of the Na2(H2PO2)2 -Ba(H2PO2)2-H2O ternary water–salt system at room temperature Res...

Seebeck effect of some thin film carbides

International Nuclear Information System (INIS)

Beensh-Marchwicka, G.; Prociow, E.

2002-01-01

Several materials have been investigated for high-temperature thin film thermocouple applications. These include silicon carbide with boron (Si-C-B), ternary composition based on Si-C-Mn, fourfold composition based on Si-C-Zr-B and tantalum carbide (TaC). All materials were deposited on quartz or glass substrates using the pulse sputter deposition technique. Electrical conduction and thermoelectric power were measured for various compositions at 300-550 K. It has been found, that the efficiency of thermoelectric power of films containing Si-C base composition was varied from 0.0015-0.034 μW/cmK 2 . However for TaC the value about 0.093 μW/cmK 2 was obtained. (author)

The Cr–Fe–Nb ternary system: Experimental isothermal sections at 700 °C, 1050 °C and 1350 °C

Energy Technology Data Exchange (ETDEWEB)

Jacob, Aurélie, E-mail: a.jacob@fz-juelich.de [Forschungszentrum Juelich, IEK-2, 52425 Juelich (Germany); Schmetterer, Clemens [Forschungszentrum Juelich, IEK-2, 52425 Juelich (Germany); Fraunhofer-UMSICHT, 92237 Sulzbach-Rosenberg (Germany); Grüner, Daniel; Wessel, Egbert [Forschungszentrum Juelich, IEK-2, 52425 Juelich (Germany); Hallstedt, Bengt [Institute for Materials Applications in Mechanical Engineering, RWTH Aachen University, Augustinerbach 4, 52062 Aachen (Germany); Singheiser, Lorenz [Forschungszentrum Juelich, IEK-2, 52425 Juelich (Germany)

2015-11-05

The Cr–Fe–Nb system is an important constituent system in the development of Laves-phase reinforced steels. It contains two Laves-phase polytypes, i.e. C14–Fe{sub 2}Nb and C15–Cr{sub 2}Nb. While the first forms a substantial ternary solid solution with Cr, the latter only shows a limited solubility for Fe. The phase equilibria in the Cr–Fe–Nb system are shown in three isothermal sections at 700, 1050 and 1350 °C. Scanning electron microscopy coupled with energy dispersive X-ray analysis (SEM/EDX), X-ray diffraction (XRD) and electron back scatter diffraction (EBSD) were used to determine the phase equilibria from which the isothermal sections were constructed. - Highlights: • Determination of Phase Equilibria in the Cr–Fe–Nb system at 700, 1050 and 1350 °C. • Isothermal sections at 700, 1050 and 1350 °C were established. • Homogeneity range of Laves phases were determined. • Solubility of Fe and Cr and lattice parameter evolution in the ternary phases were determined.

Ternary liquid-liquid equilibria for mixtures of toluene + n-heptane + an ionic liquid

NARCIS (Netherlands)

Meindersma, G.W.; Podt, J.G.; de Haan, A.B.

2006-01-01

This research has been focused on a study of sulfolane and four ionic liquids as solvents in liquid–liquid extraction. Liquid–liquid equilibria data were obtained for mixtures of (sulfolane or 4-methyl-N-butylpyridinium tetrafluoroborate ([mebupy]BF4) or 1-ethyl-3-methylimidazolium ethylsulfate

Thermodynamic Calculation of Carbide Precipitate in Niobium Microalloyed Steels

Institute of Scientific and Technical Information of China (English)

XU Yun-bo; YU Yong-mei; LIU Xiang-hua; WANG Guo-dong

2006-01-01

On the basis of regular solution sublattice model, thermodynamic equilibrium of austenite/carbide in Fe-Nb-C ternary system was investigated. The equilibrium volume fraction, chemical driving force of carbide precipitates and molar fraction of niobium and carbon in solution at different temperatures were evaluated respectively. The volume fraction of precipitates increases, molar fraction of niobium dissolved in austenite decreases and molar fraction of carbon increases with decreasing the niobium content. The driving force increases with the decrease of temperature, and then comes to be stable at relatively low temperatures. The predicted ratio of carbon in precipitates is in good agreement with the measured one.

Experimental study of the Cu-Al-Sn phase equilibria, close to the copper zone

Directory of Open Access Journals (Sweden)

Soares D.F.

2017-01-01

Full Text Available The ternary Cu-Al-Sn phase diagram is the base for several important types of alloys, with relevant industrial interest and applications. The knowledge of the melting/solidification alloys characteristics are determinant for their preparation and properties control. However, there is a lack of experimental information on the ternary phase diagram, at high temperature. In this work, several alloys, with high copper content and additions of Al, up to 10%, and Sn, up to 14% (in wt%, were studied by thermal analysis and by isothermal phase equilibria determination. The alloys liquidus and solidus lines and the binary α + β phase field, at 800°C, are presented for the studied range of compositions.

Vapor-liquid equilibria of binary and ternary mixtures of acetaldehyde with Versatic 9 and Veova 9

NARCIS (Netherlands)

Raeissi, S.; Florusse, L.J.; Kroon, M.C.; Peters, C.J.

2016-01-01

In continuation of our earlier publication on the phase behavior of binary and ternary mixtures involving acetaldehyde, Versatic 10, and Veova 10, in this work we present bubble-point pressures of the binary and ternary systems of acetaldehyde, Versatic 9, and Veova 9. The measurements were carried

Investigations of carbon diffusion and carbide formation in nickel-based alloys

International Nuclear Information System (INIS)

Schulten, R.; Bongartz, K.; Quadakkers, W.J.; Schuster, H.; Nickel, H.

1989-11-01

The present thesis describes the carburization behaviour of nickel based alloys in heavily carburizing environments. The mechanisms of carbon diffusion and carbide precipitation in NiCr alloys with and without ternary additions of iron, cobalt or molybdenum have been investigated. Using the results of carburization experiments, a mathematical model which describes carbon diffusion and carbide formation, was developed. The simulation of the carburization process was carried out by an iterative calculation of the local thermodynamic equilibrium in the alloy. An accurate description of the carbon profiles as a function of time became possible by using a finite-difference calculation. (orig.) [de

Phase equilibria and thermodynamics of the Fe–Al–C system: Critical evaluation, experiment and thermodynamic optimization

International Nuclear Information System (INIS)

Phan, Anh Thu; Paek, Min-Kyu; Kang, Youn-Bae

2014-01-01

In order to provide an efficient tool to design alloy chemistry and processing conditions for high-strength, lightweight steel, an investigation of the Fe–Al–C ternary system was carried out by experimental phase diagram measurement and a CALPHAD thermodynamic analysis. Discrepancies between previously available experimental results and thermodynamic calculations were identified. The Fe–Al sub-binary system was re-optimized in order to obtain an accurate description of the liquid phase, while Gibbs energies of solid phases were mainly taken from a previous thermodynamic modeling. Phase equilibria among face-centered cubic (fcc)/body-centered cubic (bcc)/graphite/κ-carbide/liquid phases in the Fe–Al–C system in the temperature range from 1000 to 1400 °C were obtained by chemical equilibration followed by quenching, and subsequent composition analysis using electron probe microanalysis/inductively coupled plasma spectroscopy. By merging the revised Fe–Al binary description with existing Fe–C and Al–C binary descriptions, a complete thermodynamic description of the Fe–Al–C system was obtained in the present study. The modified quasi-chemical model in the pair approximation was used to model the liquid phase, while solid solutions were modeled using compound energy formalism. A2/B2 order/disorder transition in the bcc phase was taken into account. Compared with previously known experiments/thermodynamic modeling, a better agreement was obtained in the present study, regarding the stable region of fcc and the solidification thermal peak of a ternary alloy near the liquidus temperature. The obtained thermodynamic description also reproduced various types of experimental data in the Fe–Al–C system such as isothermal sections, vertical sections, liquidus projection, etc. The solidification of various steel grades was predicted and discussed

Phase equilibrium properties of binary and ternary systems containing di-isopropyl ether + 1-butanol + benzene at 313.15 K

International Nuclear Information System (INIS)

Villamanan, Rosa M.; Martin, M. Carmen; Chamorro, Cesar R.; Villamanan, Miguel A.; Segovia, Jose J.

2006-01-01

(Vapour + liquid) equilibria data of (di-isopropyl ether + 1-butanol + benzene) (di-isopropyl ether + 1-butanol) and (1-butanol + benzene) have been measured at T = 313.15 K using an isothermal total pressure cell. Data reduction by Barker's method provides correlations for the excess molar Gibbs energy using the Margules equation for the binary systems and the Wohl expansion for the ternary. The Wilson, NRTL and UNIQUAC models have been applied successfully to both the binary and the ternary systems reported here

Phase equilibria in Dy-Cu-Al system at 500 deg C

International Nuclear Information System (INIS)

Kuz'ma, Yu.B.; Milyan, V.V.

1989-01-01

Using the methods of X-ray diffraction analysis a diagram of phase equilibria in Dy-Cu-Al system at 500 deg C is plotted. Boundaries of solid solutions on the basis of DyCu 2 , DyCu and DyAl 2 compounds are determined and homogeneity regions of ternary compounds Dy 2 (Cu, Al) 7 and Dy(CuAl) 5 are ascertained. Compounds DyCuAl 3 , Dy 4 Cu 4 Al 11 and Dy 5 Cu 6 Al 9 have been detected for the first time

Modeling adsorption of binary and ternary mixtures on microporous media

DEFF Research Database (Denmark)

Monsalvo, Matias Alfonso; Shapiro, Alexander

2007-01-01

it possible using the same equation of state to describe the thermodynamic properties of the segregated and the bulk phases. For comparison, we also used the ideal adsorbed solution theory (IAST) to describe adsorption equilibria. The main advantage of these two models is their capabilities to predict......The goal of this work is to analyze the adsorption of binary and ternary mixtures on the basis of the multicomponent potential theory of adsorption (MPTA). In the MPTA, the adsorbate is considered as a segregated mixture in the external potential field emitted by the solid adsorbent. This makes...... multicomponent adsorption equilibria on the basis of single-component adsorption data. We compare the MPTA and IAST models to a large set of experimental data, obtaining reasonable good agreement with experimental data and high degree of predictability. Some limitations of both models are also discussed....

Investigations of the ternary system beryllium-carbon-tungsten and analyses of beryllium on carbon surfaces

International Nuclear Information System (INIS)

Kost, Florian

2009-01-01

Beryllium, carbon and tungsten are planned to be used as first wall materials in the future fusion reactor ITER. The aim of this work is a characterization of mixed material formation induced by thermal load. To this end, model systems (layers) were prepared and investigated, which give insight into the basic physical and chemical concepts. Before investigating ternary systems, the first step was to analyze the binary systems Be/C and Be/W (bottom-up approach), where the differences between the substrates PG (pyrolytic graphite) and HOPG (highly oriented pyrolytic graphite) were of special interest. Particularly X-ray photoelectron spectroscopy (XPS), low energy ion scattering (ISS) and Rutherford backscattering spectroscopy (RBS) were used as analysis methods. Beryllium evaporated on carbon shows an island growth mode, whereas a closed layer can be assumed for layer thicknesses above 0.7 nm. Annealing of the Be/C system induces Be 2 C island formation for T≥770 K. At high temperatures (T≥1170 K), beryllium carbide dissociates, resulting in (metallic) beryllium desorption. For HOPG, carbide formation starts at higher temperatures compared to PG. Activation energies for the diffusion processes were determined by analyzing the decreasing beryllium amount versus annealing time. Surface morphologies were characterized using angle-resolved XPS (ARXPS) and atomic force microscopy (AFM). Experiments were performed to study processes in the Be/W system in the temperature range from 570 to 1270 K. Be 2 W formation starts at 670 K, a complete loss of Be 2 W is observed at 1170 K due to dissociation (and subsequent beryllium desorption). Regarding ternary systems, particularly Be/C/W and C/Be/W were investigated, attaching importance to layer thickness (reservoir) variations. At room temperature, Be 2 C, W 2 C, WC and Be 2 W formation at the respective interfaces was observed. Further Be 2 C is forming with increasing annealing temperatures. Depending on the layer

Solid-Liquid and Liquid-Liquid Equilibrium in the Ternary System Acetic Acid-Propanoic Acid-Formamide.

Czech Academy of Sciences Publication Activity Database

Sedláková, Zuzana; Malijevská, I.

2007-01-01

Roč. 261, 1-2 (2007) , s. 129-132 ISSN 0378-3812. [International Conference on Properties and Phase Equilibria for Product and Process Design PPEPPD 2007 /11./. Hersonissos, Crete, 20.05.2007-25.05.2007] Institutional research plan: CEZ:AV0Z40720504 Keywords : solid-liquid equilibrium * ternary system * solid adduct Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 1.506, year: 2007

The phase equilibria in the Ti-Cu-Y ternary system at 773 K

Energy Technology Data Exchange (ETDEWEB)

Hu Zhaohua [Key Laboratory of Nonferrous Metal Materials and New Processing Technology, Ministry of Education, Guangxi University, Nanning, Guangxi 530004 (China); Zhan Yongzhong, E-mail: zyzmatres@yahoo.com.c [Key Laboratory of Nonferrous Metal Materials and New Processing Technology, Ministry of Education, Guangxi University, Nanning, Guangxi 530004 (China); She Jia; Zhang Guanghua; Peng Dan [Key Laboratory of Nonferrous Metal Materials and New Processing Technology, Ministry of Education, Guangxi University, Nanning, Guangxi 530004 (China)

2009-10-19

Physical-chemical analysis apparatuses, including X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and differential thermal analysis (DTA) were employed in constructing the isothermal section of the Ti-Cu-Y system at 773 K. The existences of 10 binary compounds, Ti{sub 2}Cu, TiCu, Ti{sub 3}Cu{sub 4}, Ti{sub 2}Cu{sub 3}, TiCu{sub 4}, Cu{sub 6}Y, Cu{sub 4}Y, Cu{sub 7}Y{sub 2}, Cu{sub 2}Y and CuY were confirmed. The isothermal section consists of 13 single-phase regions, 23 binary phase regions and 11 ternary phase regions. No ternary compound is found in this work. Except the binary compounds YCu{sub 6} and TiCu{sub 4} show homogeneity regions less than 1.5 at.%, none of the other phases in this system reveals a remarkable homogeneity range at 773 K.

Neutron Damage and MAX Phase Ternary Compounds

Energy Technology Data Exchange (ETDEWEB)

Barsoum, Michael [Drexel Univ., Philadelphia, PA (United States); Hoffman, Elizabeth [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Sindelar, Robert [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Garcua-Duaz, Brenda [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Kohse, Gordon [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

2014-06-17

The Demands of Gen IV nuclear power plants for long service life under neutron radiation at high temperature are severe. Advanced materials that would withstand high temperatures (up to 1000+ C) to high doses in a neutron field would be ideal for reactor internal structures and would add to the long service life and reliability of the reactors. The objective of this work is to investigate the response of a new class of machinable, conductive, layered, ternary transition metal carbides and nitrides - the so-called MAX phases - to low and moderate neutron dose levels.

Neutron Damage and MAX Phase Ternary Compounds

International Nuclear Information System (INIS)

Barsoum, Michael; Hoffman, Elizabeth; Sindelar, Robert; Garcua-Diaz, Brenda; Kohse, Gordon

2014-01-01

The Demands of Gen IV nuclear power plants for long service life under neutron radiation at high temperature are severe. Advanced materials that would withstand high temperatures (up to 1000+ C) to high doses in a neutron field would be ideal for reactor internal structures and would add to the long service life and reliability of the reactors. The objective of this work is to investigate the response of a new class of machinable, conductive, layered, ternary transition metal carbides and nitrides - the so-called MAX phases - to low and moderate neutron dose levels.

Prediction of high pressure vapor-liquid equilibria with mixing rule using ASOG group contribution method

Energy Technology Data Exchange (ETDEWEB)

Tochigi, K.; Kojima, K.; Kurihara, K.

1985-02-01

To develop a widely applicable method for predicting high-pressure vapor-liquid equilibria by the equation of state, a mixing rule is proposed in which mixture energy parameter ''..cap alpha..'' of theSoave-RedlichKwong, Peng-Robinson, and Martin cubic equations of state is expressed by using the ASOG group contribution method. The group pair parameters are then determined for 14 group pairs constituted by six groups, i.e. CH/sub 4/, CH/sub 3/, CH/sub 2/, N/sub 2/, H/sub 2/, and CO/sub 2/ groups. By using the group pair parameters determined, high-pressure vapor-liquid equilibria are predicted with good accuracy for binary and ternary systems constituted by n-paraffins, nitrogen, hydrogen, and carbon dioxide in the temperature range of 100 - 450K.

Thermodynamic models for vapor-liquid equilibria of nitrogen + oxygen + carbon dioxide at low temperatures

Science.gov (United States)

Vrabec, Jadran; Kedia, Gaurav Kumar; Buchhauser, Ulrich; Meyer-Pittroff, Roland; Hasse, Hans

2009-02-01

For the design and optimization of CO 2 recovery from alcoholic fermentation processes by distillation, models for vapor-liquid equilibria (VLE) are needed. Two such thermodynamic models, the Peng-Robinson equation of state (EOS) and a model based on Henry's law constants, are proposed for the ternary mixture N 2 + O 2 + CO 2. Pure substance parameters of the Peng-Robinson EOS are taken from the literature, whereas the binary parameters of the Van der Waals one-fluid mixing rule are adjusted to experimental binary VLE data. The Peng-Robinson EOS describes both binary and ternary experimental data well, except at high pressures approaching the critical region. A molecular model is validated by simulation using binary and ternary experimental VLE data. On the basis of this model, the Henry's law constants of N 2 and O 2 in CO 2 are predicted by molecular simulation. An easy-to-use thermodynamic model, based on those Henry's law constants, is developed to reliably describe the VLE in the CO 2-rich region.

Transition metal carbide nanocomposite and amorphous thin films

OpenAIRE

Tengstrand, Olof

2014-01-01

This thesis explores thin films of binary and ternary transition metal carbides, in the Nb-C, Ti-Si-C, Nb-Si-C, Zr-Si-C, and Nb-Ge-C systems. The electrical and mechanical properties of these systems are affected by their structure and here both nanocomposite and amorphous thin films are thus investigated. By appropriate choice of transition metal and composition the films can be designed to be multifunctional with a combination of properties, such as low electric resistivity, low contact res...

Experimental and thermodynamic investigation of Al-Cu-Nd ternary system

Energy Technology Data Exchange (ETDEWEB)

Bai, W.M. [School of Materials Science and Engineering, Central South University, Changsha, 410083 (China); Jiang, Y. [Hunan Sushi Guangbo Testing Techniques Co. LTD, Changsha (China); Guo, Z.Y.; Zeng, L.J.; Tan, M.Y. [School of Materials Science and Engineering, Central South University, Changsha, 410083 (China); Meggs, C. [School of Metallurgy and Materials, The University of Birmingham, Edgbaston, Birmingham, B15 2TT (United Kingdom); Zhang, L.G., E-mail: ligangzhang@csu.edu.cn [School of Materials Science and Engineering, Central South University, Changsha, 410083 (China); Liu, L.B., E-mail: pdc@csu.edu.cn [School of Materials Science and Engineering, Central South University, Changsha, 410083 (China); Jin, Z.P. [School of Materials Science and Engineering, Central South University, Changsha, 410083 (China)

2017-07-01

The phase relationships in the Al–Cu-Nd ternary system at 673 K have been investigated by X-ray powder diffraction (XRD) and scanning electron microscope (SEM) with energy disperse X-ray spectroscopy (EDS) in backscattered electron imaging (BSE) modes. The existence of six ternary Stoichiometric compounds, namely τ{sub 1}-Al{sub 8}Cu{sub 4}Nd, τ{sub 2}-Al{sub 9}Cu{sub 8}Nd{sub 2}, τ{sub 3}-Al{sub 6}Cu{sub 7}Nd, τ{sub 4}-Al{sub 2.4}Cu{sub 8.6}Nd, τ{sub 5}-Al{sub 3}CuNd, τ{sub 6}-AlCuNd, have been confirmed. A complete thermodynamic description of the Al–Cu-Nd ternary system coupled with the CALPHAD method is obtained based on experimental results and first-principles calculations. The calculated phase equilibria were in agreement with the available experimental data. - Highlights: • Phase relationships in the Al-Cu-Nd system has been systematically investigated. • 9 three-phase regions and 4 two-phase regions are confirmed. • A complete thermodynamic description of the Al-Cu-Nd system is obtained. • Results of first-principle calculation consist with thermodynamic calculation.

Isobaric vapor-liquid equilibria for the extractive distillation of 2-propanol + water mixtures using 1-ethyl-3-methylimidazolium dicyanamide ionic liquid

International Nuclear Information System (INIS)

Orchillés, A. Vicent; Miguel, Pablo J.; González-Alfaro, Vicenta; Llopis, Francisco J.; Vercher, Ernesto; Martínez-Andreu, Antoni

2017-01-01

Highlights: • VLE of binary and ternary systems of 2-propanol, water and [emim][DCA] at 100 kPa. • The e-NRTL model fits the VLE data of 2-propanol + water + [emim][DCA] system. • [emim][DCA] breaks the 2-propanol + water azeotrope at an IL mole fraction >0.085. - Abstract: Isobaric vapor–liquid equilibria for the binary systems 2-propanol + water, 2-propanol + 1-ethyl-3-methylimidazolium dicyanamide ([emim][DCA]), and water + [emim][DCA] as well as the vapor–liquid equilibria for the 2-propanol + water + [emim][DCA] ternary system have been obtained at 100 kPa using a recirculating still. The electrolyte nonrandom two-liquid (e-NRTL) model was used for fitting successfully the experimental data. The effect of [emim][DCA] on the 2-propanol + water system has been compared with that produced by other ionic liquids reported in the literature. From the results, [emim][DCA] appears as a good entrainer for the extractive distillation of this solvent mixture, causing the azeotrope to disappear at 100 kPa when the ionic liquid mole fraction is greater than 0.085.

Some new protonated ternary complexes of rare-earths with CDTA/DTPA and keto-glutaric acid

International Nuclear Information System (INIS)

Tripathi, S.P.; Chaturvedi, G.K.; Sharma, R.C.

1981-01-01

Potentiometric evidences have been cited for the formation of 1:1:1, M(III)-CDTA/DTPA-H 2 KGA ternary complexes in the solution equilibria (where M(III)=LA(III), Pr(III), Nd(III), Gd(III) or Dy(III); CDTA=1,2-diaminocyclohexanetetra-acetic acid; DTPA=diethylenetriaminepenta-acetic acid and H 2 KGA= β-ketoglutaric acid). Indications have been cited for the formation of protonated mixed ligand complexes at low pH as intermediate products, which undergo deprotonation at comparatively high pH forming 1:1:1, ternary species. The formation constants (log Ksub(MLL')) for the protonated ternary species, formed by simultaneous addition of both the ligands to metal ion and their deprotonation constants - log Ksub(A)sup(H) have been evaluated. The following order in the relative stabilities of the resulting complexes in terms of metal ions, La(III) < Pr(III) < Nd(III) < Gd(III) < Dy(III), has been observed. (author)

Robust tribo-mechanical and hot corrosion resistance of ultra-refractory Ta-Hf-C ternary alloy films.

Science.gov (United States)

Yate, Luis; Coy, L Emerson; Aperador, Willian

2017-06-08

In this work we report the hot corrosion properties of binary and ternary films of the Ta-Hf-C system in V 2 O 5 -Na 2 SO 4 (50%wt.-50%wt.) molten salts at 700 °C deposited on AISI D3 steel substrates. Additionally, the mechanical and nanowear properties of the films were studied. The results show that the ternary alloys consist of solid solutions of the TaC and HfC binary carbides. The ternary alloy films have higher hardness and elastic recoveries, reaching 26.2 GPa and 87%, respectively, and lower nanowear when compared to the binary films. The corrosion rates of the ternary alloys have a superior behavior compared to the binary films, with corrosion rates as low as 0.058 μm/year. The combination and tunability of high hardness, elastic recovery, low nanowear and an excellent resistance to high temperature corrosion demonstrates the potential of the ternary Ta-Hf-C alloy films for applications in extreme conditions.

Attractive evolutionary equilibria

NARCIS (Netherlands)

Joosten, Reinoud A.M.G.; Roorda, Berend

2011-01-01

We present attractiveness, a refinement criterion for evolutionary equilibria. Equilibria surviving this criterion are robust to small perturbations of the underlying payoff system or the dynamics at hand. Furthermore, certain attractive equilibria are equivalent to others for certain evolutionary

Modeling strontium-cesium-calcium-magnesium-sodium ion exchange equilibria on chabazite with the Wilson equation

International Nuclear Information System (INIS)

Perona, J.J.

1992-01-01

Chabazite zeolites are used at ORNL for decontamination of wastewaters containing 90 Sr and 137 Cs. Treatability studies have shown that chabazite can remove trace amounts of these nuclides from wastewaters containing much higher concentrations of calcium and magnesium. The design of ion exchange columns for multicomponent systems requires a method for predicting multicomponent equilibria from binary or ternary experiments, since the number of experiments required for an empirical equilibrium model is generally not feasible. Binary interaction parameters for the Wilson equation were used to predict solid-phase activity coefficients for the five-component system, and the sum of squares of deviations between experimental and predicted solution concentrations for the data points available was calculated. The average deviation per data point for the five-component system was about the same as for the calcium-magnesium-sodium ternary system

Phase equilibria in the iron oxide-cobalt oxide-phosphorus oxide system

Science.gov (United States)

De Guire, Mark R.; Prasanna, T. R. S.; Kalonji, Gretchen; O'Handley, Robert C.

1987-01-01

Two novel ternary compounds are noted in the present study of 1000 C solid-state equilibria in the Fe-Co-P-O system's Fe2O3-FePO4-Co3(Po4)2-CoO region: CoFe(PO4)O, which undergoes incongruent melting at 1130 C, and Co3Fe4(PO4)6, whose incongruent melting occurs at 1080 C. The liquidus behavior-related consequences of rapidly solidified cobalt ferrite formation from cobalt ferrite-phosphate melts are discussed with a view to spinel formation. It is suggested that quenching from within the spinel-plus-liquid region may furnish an alternative to quenching a homogeneous melt.

Evaluation of the polysubstituted pyridinium ionic liquid [hmmpy][Ntf2] as a suitable solvent for desulfurization: Phase equilibria

International Nuclear Information System (INIS)

Arce, Alberto; Francisco, Maria; Soto, Ana

2010-01-01

Suitability of a pyridinium ionic liquid as a solvent in desulfurization has been analyzed. (Liquid + liquid) equilibria for ternary systems composed by 1-hexyl-3,5-dimethyl pyridinium {bis[trifluoromethylsulfonyl]imide, thiophene, and three hydrocarbons representative of fuel (n-heptane, 2,2,4 trimethylpentane, and toluene) have been determined at T = 298.15 K and atmospheric pressure. High solubility of thiophene in the ionic liquid and also of toluene have been found, being this solvent practically immiscible with 2,2,4 trimethylpentane and heptane. Equilibrium data of these systems have been well correlated with UNIQUAC equations finding the highest deviations for the ternary system involving toluene. NRTL model drove to worse results being considered as not suitable model to correlate the experimental results.

Phase transformation and microstructure study of the as-cast Cu-rich Cu-Al-Mn ternary alloys

Directory of Open Access Journals (Sweden)

Holjevac-Grgurić T.

2017-01-01

Full Text Available Four Cu-rich alloys from the ternary Cu-Al-Mn system were prepared in the electric-arc furnace and casted in cylindrical moulds with dimensions: f=8 mm and length 12 mm. Microstructural investigations of the prepared samples were performed by using optical microscopy (OM and scanning electron microscopy, equipped by energy dispersive spectroscopy (SEM-EDS. Assignation of crystalline phases was confirmed by XRD analysis. Phase transition temperatures were determined using simultaneous thermal analyzer STA DSC/TG. Phase equilibria calculation of the ternary Cu-Al-Mn system was performed using optimized thermodynamic parameters from literature. Microstructure and phase transitions of the prepared as-cast alloys were investigated and experimental results were compared with the results of thermodynamic calculations.

Metastable nanocrystalline carbides in chemically synthesized W-Co-C ternary alloys

International Nuclear Information System (INIS)

McCandlish, L.E.; Kear, B.H.; Kim, B.K.; Wu, L.W.

1989-01-01

Nanophase materials can be prepared either by physical methods or chemical methods. Physical methods include thermal evaporation, sputtering and melt quenching, whereas chemical methods include glow-discharge decomposition, chemical vapor deposition, sol-gel dehydration and gas-solid reaction. Recently, the authors have used controlled activity gas-solid reactions to prepare nanophase WC-Co cermet powders at different WC loadings. In the process they have discovered some new metastable phases in the W-Co-C ternary system at temperatures below 1000 degrees C

(Liquid + liquid) equilibria of four alcohol–water systems containing 1,8-cineole at T = 298.15 K

International Nuclear Information System (INIS)

Li, Hengde; Feng, Zhangni; Wan, Li; Huang, Cheng; Zhang, Tianfei; Fang, Yanxiong

2016-01-01

Graphical abstract: (Liquid + liquid) equilibria of C_1–C_4 alcohol–water systems containing 1,8-cineole are presented. Distribution ratios of alcohol in the mixtures are examined. The immiscible region of the LLE systems is evaluated and discussed. - Highlights: • Ternary (liquid + liquid) equilibria containing 1,8-cineole are presented. • Distribution ratios of C_1–C_4 alcohol in the mixtures are examined. • The LLE values were correlated using the NRTL and UNIQUAC models. - Abstract: As an eco-friendly compound from essential oils, 1,8-cineole (cineole, eucalyptol) has the potential to replace the ozone depleting industrial solvents. This paper presents experimental (liquid + liquid) equilibrium (LLE) data for four alcohol–water systems containing 1,8-cineole. To evaluate the phase equilibrium properties of 1,8-cineole in aqueous alcohol mixtures, LLE values for the ternary systems (water + methanol or ethanol or 1-propanol or 1-butanol + 1,8-cineole) were determined with a tie-line method at T = 298.15 K under atmospheric pressure. The well-known Hand, Bachman and Othmer–Tobias equations were used to test the reliability of the experimental results. The binodal curves and distribution ratios of alcohol in the mixtures are shown and discussed. The experimental LLE values were satisfactorily correlated by the NRTL and UNIQUAC models.

Ebulliometric determination and prediction of (vapor + liquid) equilibria for binary and ternary mixtures containing alcohols (C1-C4) and dimethyl carbonate

International Nuclear Information System (INIS)

Matsuda, Hiroyuki; Fukano, Makoto; Kikkawa, Shinichiro; Constantinescu, Dana; Kurihara, Kiyofumi; Tochigi, Katsumi; Ochi, Kenji; Gmehling, Juergen

2012-01-01

Highlights: → The VLE behavior of systems containing dimethyl carbonate (DMC) was investigated. → VLE data for ternary and binary mixtures containing alcohol and DMC were measured. → Several activity coefficient models were used for data reduction or prediction. → Valley line, i.e., distillation boundary, was observed for the ternary mixture. → Residue curves were calculated to investigate composition profile for distillation. - Abstract: (Vapor + liquid) equilibrium (VLE) data for a ternary mixture, namely {methanol + propan-1-ol + dimethyl carbonate (DMC)}, and four binary mixtures, namely an {alcohol (C 3 or C 4 ) + DMC}, containing the binary constituent mixtures of the ternary mixture, were measured at p = (40.00 to 93.32) kPa using a modified Swietoslawski-type ebulliometer. The experimental data for the binary systems were correlated using the Wilson model. The Wilson model was also applied to the ternary system to predict the VLE behavior using parameters from the binary mixtures. The modified UNIFAC (Dortmund) model was also tested for the predictions of the VLE behavior of the binary and ternary mixtures. In addition, the experimental VLE data for the ternary and constituent binary mixtures were correlated using the extended Redlich-Kister (ERK) model, which can completely represent the azeotropic points. For the ternary system, a comparison of the experimental and the predicted or correlated boiling points obtained using the Wilson and ERK models showed that the ERK model is more accurate. The valley line, i.e., the curve which divides the patterns of vapor-liquid tie lines, was found in the (methanol + propan-1-ol + DMC) system. This valley line could be represented by the ERK model. Finally, the composition profile for simple distillation of this ternary mixture was obtained by analysis of the residue curves from the estimated Wilson parameters of the constituent binary mixtures.

Phase Equilibria of the Ternary Sn-Pb-Co System at 250°C and Interfacial Reactions of Co with Sn-Pb Alloys

Science.gov (United States)

Wang, Chao-hong; Kuo, Chun-yi; Yang, Nian-cih

2015-11-01

The isothermal section of the ternary Sn-Pb-Co system at 250°C was experimentally determined through a series of the equilibrated Sn-Pb-Co alloys of various compositions. The equilibrium phases were identified on the basis of compositional analysis. For the Sn-Co intermetallic compounds (IMCs), CoSn3, CoSn2, CoSn and Co3Sn2, the Pb solubility was very limited. There exist five tie-triangle regions. The Co-Pb system involves one monotectic reaction, so the phase separation of liquid alloys near the Co-Pb side occurred prior to solidification. The immiscibility field was also determined. Additionally, interfacial reactions between Co and Sn-Pb alloys were conducted. The reaction phase for the Sn-48 at.%Pb and Sn-58 at.%Pb at 250°C was CoSn3 and CoSn2, respectively. Both of them were simultaneously formed in the Sn-53 at.%Pb/Co. The formed IMCs were closely associated to the phase equilibria relationship of the liquid-CoSn3-CoSn2 tie-triangle. Furthermore, with increasing temperatures, the phase formed in equilibrium with Sn-37 wt.%Pb was found to transit from CoSn3 to CoSn2 at 275°C. We propose a simple method of examining the phase transition temperature in the interfacial reactions to determine the boundaries of the liquid-CoSn3-CoSn2 tie-triangles at different temperatures.

Attractive evolutionary equilibria

OpenAIRE

Roorda, Berend; Joosten, Reinoud

2011-01-01

We present attractiveness, a refinement criterion for evolutionary equilibria. Equilibria surviving this criterion are robust to small perturbations of the underlying payoff system or the dynamics at hand. Furthermore, certain attractive equilibria are equivalent to others for certain evolutionary dynamics. For instance, each attractive evolutionarily stable strategy is an attractive evolutionarily stable equilibrium for certain barycentric ray-projection dynamics, and vice versa.

Temperature dependence on mutual solubility of binary (methanol + limonene) mixture and (liquid + liquid) equilibria of ternary (methanol + ethanol + limonene) mixture

International Nuclear Information System (INIS)

Tamura, Kazuhiro; Li Xiaoli; Li Hengde

2009-01-01

Mutual solubility data of the binary (methanol + limonene) mixture at the temperatures ranging from 288.15 K close to upper critical solution temperature, and ternary (liquid + liquid) equilibrium (tie-lines) of the (methanol + ethanol + limonene) mixture at the temperatures (288.15, 298.15, and 308.15) K have been obtained. The experimental results have been represented accurately in terms of the extended and modified UNIQUAC models with binary parameters, compared with the UNIQUAC model. The temperature dependence of binary and ternary (liquid + liquid) equilibrium for the binary (methanol + limonene) and ternary (methanol + ethanol + limonene) mixtures could be calculated successfully using the extended and modified UNIQUAC model

Prediction of multiphase equilibria in associating fluids by a contact-site quasichemical equation of state

International Nuclear Information System (INIS)

Prikhodko, I.V.; Victorov, A.I.; Loos, Th.W.de

1995-01-01

A contract-site quasichemical equation of state has been used for the modeling of different kinds of fluid phase equilibria (between a gas phase and one or more liquids) over a wide range of conditions. Among the systems of interest are the ternary mixtures water + alkanols + hydrocarbons (alkanes or alkynes), water + alkanols (or acetone) + CO 2 , water + polyoxyethyleneglycol ethers + heavy alkanes. The model has been applied to describing the thermodynamic properties of the binary subsystems and to predict the phase behavior of the ternary systems. For longer-chain alkanols and hydrocarbons a group-contribution approach is implemented, which allows the modeling when no experimental data are available. The model gives reasonable predictions of phase behavior and the correct trends in the calculated phase diagrams in most cases. The concentrations of associates in liquid and gas phases are estimated by the model and compared with some experimental and computer simulation data. The predictive abilities of the model, its limitations, and possible ways of its improvement are discussed

Binary, ternary and quaternary liquid-liquid equilibria in 1-butanol, oleic acid, water and n-heptane mixtures

NARCIS (Netherlands)

Winkelman, J. G. M.; Kraai, G. N.; Heeres, H. J.

2009-01-01

This work reports on liquid-liquid equilibria in the system 1-butanol, oleic acid, water and n-heptane used for biphasic, lipase catalysed esterifications. The literature was studied on the mutual solubility in binary systems of water and each of the organic components. Experimental results were

Stable and metastable equilibria in PbSe + SnI2=SnSe + PbI2

International Nuclear Information System (INIS)

Odin, I.N.; Grin'ko, V.V.; Kozlovskij, V.F.; Demidova, E.D.

2003-01-01

T-x-y phase diagrams of the PbSe + SnI 2 =SnSe + PbI 2 mutual system (stable states) are plotted for the first time. It is shown that melt, solid solutions on the base of components of the mutual system and phase on the base of Sn 2 SeI 4 take part in phase equilibria. Transformations in the PbSe + SnI 2 =SnSe + PbI 2 mutual system leading to crystallization of metastable polytype modifications of lead iodides and metastable ternary compound forming in PbSe-PbI 2 system are investigated for the first time [ru

Phase equilibria in the Ni–Al–Ga system at 700 °C

International Nuclear Information System (INIS)

Belyavina, N.; Markiv, V.; Nakonechna, O.; Lozovyi, F.

2014-01-01

Graphical abstract: - Highlights: • We study phase equilibria in ternary Ni–Al–Ga in the whole concentration range. • Ni(Al,Ga), Ni 2 (Al,Ga) 3 , Ni 5 (Al,Ga) 3 extended solid solutions exist in this system. • Isothermal section (700 °C) of the Ni–Al–Ga system has been constructed. • Small additions of Ga increase compressive strength of Ni 3 (Al,Ga) solid solution. - Abstract: Phase relations in the ternary Ni–Al–Ga system at 700 °C have been established by the X-ray powder diffraction methods. In addition to already known Ni 3 (Al,Ga) continuous solid solution, Ni(Al,Ga) continuous solid solution as well as Ni 2 (Al,Ga) 3 and Ni 5 (Al,Ga) 3 extended solid solutions were found to exist in this system. It was shown that the ternary Ni 2 (Al,Ga) 3 and Ni 5 (Al,Ga) 3 compounds do not belong to the continuous solid solutions because of two-phase gaps on the Ni 2 Al 3 –Ni 2 Ga 3 (∼30–50 at.% Ga) and Ni 5 Al 3 –Ni 5 Ga 3 (∼12–25 at.% Ga) isolines at 700 °C. Some crystal structure peculiarities such as atomic ordering–disordering and presence of structural vacancies have been revealed for all solid solutions existing in the Ni–Al–Ga system. It was found that the compressive strength of the Ni 3 (Al,Ga) solid solution increases with small additions of gallium (about 2.5 at.%). The isothermal section (700 °C) of the ternary Ni–Al–Ga system including four extended solid solutions (Ni 3 (Al,Ga), Ni 5 (Al,Ga) 3 , Ni(Al,Ga) and Ni 2 (Al,Ga) 3 ) has been constructed and plotted

Phase equilibria in the BaUO3-BaZrO3-BaMoO3 system

International Nuclear Information System (INIS)

Kurosaki, Ken; Yamanaka, Shinsuke; Matsuda, Tetsushi; Uno, Masayoshi; Yamamoto, Kazuya; Namekawa, Takashi

2002-01-01

The phase equilibria in the pseudo-ternary BaUO 3 -BaZrO 3 -BaMoO 3 system were studied to understand the thermochemical properties of the perovskite type gray oxide phase in high burnup MOX fuel. Thermodynamic equilibrium calculation for the system was performed by using a Chem Sage program under the various oxygen potentials. Solid solutions existing in the system were treated by an ideal solution model. The present calculation results well agreed with the previous reported post irradiation examination results, showing that BaMoO 3 was scarcely included in the gray oxide phase. (author)

Ebulliometric determination and prediction of (vapor + liquid) equilibria for binary and ternary mixtures containing alcohols (C{sub 1}-C{sub 4}) and dimethyl carbonate

Energy Technology Data Exchange (ETDEWEB)

Matsuda, Hiroyuki, E-mail: matsuda@chem.cst.nihon-u.ac.jp [Department of Materials and Applied Chemistry, Nihon University, 1-8 Kanda Surugadai, Chiyoda-ku, Tokyo 101-8308 (Japan); Fukano, Makoto; Kikkawa, Shinichiro [Department of Materials and Applied Chemistry, Nihon University, 1-8 Kanda Surugadai, Chiyoda-ku, Tokyo 101-8308 (Japan); Constantinescu, Dana [Carl von Ossietzky Universitaet Oldenburg, Technische Chemie, D-26111 Oldenburg (Germany); Kurihara, Kiyofumi; Tochigi, Katsumi; Ochi, Kenji [Department of Materials and Applied Chemistry, Nihon University, 1-8 Kanda Surugadai, Chiyoda-ku, Tokyo 101-8308 (Japan); Gmehling, Juergen [Carl von Ossietzky Universitaet Oldenburg, Technische Chemie, D-26111 Oldenburg (Germany)

2012-01-15

Highlights: > The VLE behavior of systems containing dimethyl carbonate (DMC) was investigated. > VLE data for ternary and binary mixtures containing alcohol and DMC were measured. > Several activity coefficient models were used for data reduction or prediction. > Valley line, i.e., distillation boundary, was observed for the ternary mixture. > Residue curves were calculated to investigate composition profile for distillation. - Abstract: (Vapor + liquid) equilibrium (VLE) data for a ternary mixture, namely {l_brace}methanol + propan-1-ol + dimethyl carbonate (DMC){r_brace}, and four binary mixtures, namely an {l_brace}alcohol (C{sub 3} or C{sub 4}) + DMC{r_brace}, containing the binary constituent mixtures of the ternary mixture, were measured at p = (40.00 to 93.32) kPa using a modified Swietoslawski-type ebulliometer. The experimental data for the binary systems were correlated using the Wilson model. The Wilson model was also applied to the ternary system to predict the VLE behavior using parameters from the binary mixtures. The modified UNIFAC (Dortmund) model was also tested for the predictions of the VLE behavior of the binary and ternary mixtures. In addition, the experimental VLE data for the ternary and constituent binary mixtures were correlated using the extended Redlich-Kister (ERK) model, which can completely represent the azeotropic points. For the ternary system, a comparison of the experimental and the predicted or correlated boiling points obtained using the Wilson and ERK models showed that the ERK model is more accurate. The valley line, i.e., the curve which divides the patterns of vapor-liquid tie lines, was found in the (methanol + propan-1-ol + DMC) system. This valley line could be represented by the ERK model. Finally, the composition profile for simple distillation of this ternary mixture was obtained by analysis of the residue curves from the estimated Wilson parameters of the constituent binary mixtures.

Modelling (vapour + liquid) and (vapour + liquid + liquid) equilibria of {water (H2O) + methanol (MeOH) + dimethyl ether (DME) + carbon dioxide (CO2)} quaternary system using the Peng-Robinson EoS with Wong-Sandler mixing rule

International Nuclear Information System (INIS)

Ye Kongmeng; Freund, Hannsjoerg; Sundmacher, Kai

2011-01-01

Highlights: → Phase behaviour modelling of H 2 O-MeOH-DME under pressurized CO 2 (anti-solvent) using PRWS. → PRWS-UNIFAC-PSRK has better performance than PRWS-UNIFAC-Lby in general. → Reliable to extend the VLE and VLLE phase behaviour from binary to multicomponent systems. → Successful prediction of the VLE and VLLE of binary, ternary, and quaternary systems. → Potential to apply the model for designing new DME separation process. - Abstract: The (vapour + liquid) equilibria (VLE) and (vapour + liquid + liquid) equilibria (VLLE) binary data from literature were correlated using the Peng-Robinson (PR) equation of state (EoS) with the Wong-Sandler mixing rule (WS). Two group contribution activity models were used in the PRWS: UNIFAC-PSRK and UNIFAC-Lby. The systems were successfully extrapolated from the binary systems to ternary and quaternary systems. Results indicate that the PRWS-UNIFAC-PSRK generally displays a better performance than the PRWS-UNIFAC-Lby.

Modelling of volumetric properties of binary and ternary mixtures by CEOS, CEOS/GE and empirical models

Directory of Open Access Journals (Sweden)

BOJAN D. DJORDJEVIC

2007-12-01

Full Text Available Although many cubic equations of state coupled with van der Waals-one fluid mixing rules including temperature dependent interaction parameters are sufficient for representing phase equilibria and excess properties (excess molar enthalpy HE, excess molar volume VE, etc., difficulties appear in the correlation and prediction of thermodynamic properties of complex mixtures at various temperature and pressure ranges. Great progress has been made by a new approach based on CEOS/GE models. This paper reviews the last six-year of progress achieved in modelling of the volumetric properties for complex binary and ternary systems of non-electrolytes by the CEOS and CEOS/GE approaches. In addition, the vdW1 and TCBT models were used to estimate the excess molar volume VE of ternary systems methanol + chloroform + benzene and 1-propanol + chloroform + benzene, as well as the corresponding binaries methanol + chloroform, chloroform + benzene, 1-propanol + chloroform and 1-propanol + benzene at 288.15–313.15 K and atmospheric pressure. Also, prediction of VE for both ternaries by empirical models (Radojković, Kohler, Jackob–Fitzner, Colinet, Tsao–Smith, Toop, Scatchard, Rastogi was performed.

The isothermal section at 500 deg. C of the Gd-Tb-Ga ternary system

International Nuclear Information System (INIS)

Li, J.Q.; Jian, Y.X.; Ao, W.Q.; Zhuang, Y.H.; He, W.

2006-01-01

Phase equilibria in the Gd-Tb-Ga ternary system at 500 deg. C were investigated by X-ray powder diffraction and differential scanning calorimetry. The binary compounds, Gd 5 Ga 3 , Gd 3 Ga 2 , GdGa, GdGa 2 , Tb 5 Ga 3 , TbGa, TbGa 2 and TbGa 3 have been confirmed at 500 deg. C. No ternary compound was found in this system. The isothermal section of this system at 500 deg. C was constructed. It is composed of 7 single-phase regions, 8 two-phase regions and 2 three-phase regions. Four ternary continuous solid solutions (Gd, Tb), (Gd, Tb) 5 Ga 3 , (Gd, Tb)Ga, (Gd, Tb)Ga 2 were formed in this isothermal section. The maximum solid solubilities of Ga in (Gd, Tb) at 500 deg. C is 5.0 at.%. The homogeneity range of (Gd, Tb)Ga 2 is from 20 to 33.3 at.% Ga in Gd-Ga side but limited in Tb-Ga side. The solid solubilities of Ga in the other phases cannot be detected. The Curie temperatures of the Gd 0.6 Tb 0.4-x Ga x alloys increase from 270 to 298 K as x increases from 0 to 0.03

Thermodynamic analysis and phase equilibria investigation in Pb−Zn−Ag system

Directory of Open Access Journals (Sweden)

Mitovski Aleksandra M.

2010-01-01

Full Text Available Physico-chemical processes that take place during the refining process in the extractive metallurgy of lead, are connected with ternary Pb−Zn−Ag system, which is necessary to study from the theoretical practical and aspects. Such investigation is important from production point of view, because of the phenomena that occur during desilvering of lead which is one of the important stages during lead refining process. Process of lead desilvering binds to ternary system Pb−Zn−Ag, which was the reason for numerous investigations, both from thermodynamic point of view and in terms of testing and determining the phase diagram, bearing in mind the theoretical, and practical importance of knowledge about the processes which are going in investigated system. The paper presents the results of thermodynamic analysis and investigation of phase equilibria of the Pb−Zn−Ag ternary system using the method of thermodynamic predictions and phase diagrams calculations, respectively, and the experimental results of metalography obtained by optical microscopy. Phase diagram of the vertical section Pb−Zn80Ag20 is presented, obtained by CALPHAD calculation methodology, and using PANDAT thermodynamic software, compared to experimental results obtained by DTA analysis. The results show a pronounced break in solubility, which is characteristic for the whole ternary Pb−Zn−Ag system. Also, it can be noticed that the thermodynamic properties follow the behavior of this system, which is expressed through positive deviation of Raoult’s law, pointing to the lack of lead affinity compared to the other two components in the system. The optical microscopy results of the investigated system show the following: - Sample L1 (weight% Pb = 98: the structure of the observed section shows double eutectic (Pbsol+Zn−Agsol which lies in the base of the primary crystals of lead (Pbsol - Samples L2−L5: the structure consists of a dual eutectic (Pbsol+Zn−Agsol and

Liquid-liquid phase equilibria for ternary systems of several polyethers with NaCl and H2O

NARCIS (Netherlands)

Milosevic, M.; Staal, K.J.J.; Schuur, Boelo; de Haan, A.B.

2014-01-01

Liquid–liquid extraction using polymers followed by induced phase separation is a potential energy reducing technology for water–salt separation. Ternary equilibrium data have been determined and reported for the (block co)poly ethers–sodium chloride–water systems at two different temperatures at

(Liquid + liquid) equilibria for ternary mixtures of (water + propionic acid + organic solvent) at T = 303.2 K

International Nuclear Information System (INIS)

Ghanadzadeh, H.; Ghanadzadeh Gilani, A.; Bahrpaima, Kh.; Sariri, R.

2010-01-01

Experimental tie-line results and phase diagrams were obtained for the ternary systems of {water + propionic acid + organic solvent (cyclohexane, toluene, and methylcyclohexane)} at T = 303.2 K and atmospheric pressure. The organic solvents were two cycloaliphatic hydrocarbons (i.e., cyclohexane and methylcyclohexane) and an aromatic hydrocarbon (toluene). The experimental tie-lines values were also compared with those calculated by the UNIQUAC and NRTL models. The consistency of the values of the experimental tie-lines was determined through the Othmer-Tobias and Hands plots. Distribution coefficients and separation factors were evaluated over the immiscibility regions and a comparison of the extracting capabilities of the solvents was made with respect to distribution coefficients and separation factors. The Kamlet LSER model was applied to correlate distribution coefficients and separation factors in these ternary systems. The LSER model values showed a good regression to the experimental results.

Ternary superconductors

International Nuclear Information System (INIS)

Giorgi, A.L.

1987-01-01

Ternary superconductors constitute a class of superconducting compounds with exceptional properties such as high transition temperatures (≅ 15.2 K), extremely high critical fields (H c2 >60 Tesla), and the coexistence of superconductivity and long-range magnetic order. This has generated great interest in the scientific community and resulted in a large number of experimental and theoretical investigations in which many new ternary compounds have been discovered. A review of some of the properties of these ternary compounds is presented with particular emphasis on the ternary molybdenum chalcogenides and the ternary rare earth transition metal tetraborides. The effect of partial substitution of a second metal atom to form pseudoternary compounds is examined as well as some of the proposed correlations between the superconducting transition temperature and the structural and electronic properties of the ternary superconductors

Learning efficient correlated equilibria

KAUST Repository

Borowski, Holly P.

2014-12-15

The majority of distributed learning literature focuses on convergence to Nash equilibria. Correlated equilibria, on the other hand, can often characterize more efficient collective behavior than even the best Nash equilibrium. However, there are no existing distributed learning algorithms that converge to specific correlated equilibria. In this paper, we provide one such algorithm which guarantees that the agents\\' collective joint strategy will constitute an efficient correlated equilibrium with high probability. The key to attaining efficient correlated behavior through distributed learning involves incorporating a common random signal into the learning environment.

Learning efficient correlated equilibria

KAUST Repository

Borowski, Holly P.; Marden, Jason R.; Shamma, Jeff S.

2014-01-01

The majority of distributed learning literature focuses on convergence to Nash equilibria. Correlated equilibria, on the other hand, can often characterize more efficient collective behavior than even the best Nash equilibrium. However, there are no existing distributed learning algorithms that converge to specific correlated equilibria. In this paper, we provide one such algorithm which guarantees that the agents' collective joint strategy will constitute an efficient correlated equilibrium with high probability. The key to attaining efficient correlated behavior through distributed learning involves incorporating a common random signal into the learning environment.

Sputtered tungsten-based ternary and quaternary layers for nanocrystalline diamond deposition.

Science.gov (United States)

Walock, Michael J; Rahil, Issam; Zou, Yujiao; Imhoff, Luc; Catledge, Shane A; Nouveau, Corinne; Stanishevsky, Andrei V

2012-06-01

Many of today's demanding applications require thin-film coatings with high hardness, toughness, and thermal stability. In many cases, coating thickness in the range 2-20 microm and low surface roughness are required. Diamond films meet many of the stated requirements, but their crystalline nature leads to a high surface roughness. Nanocrystalline diamond offers a smoother surface, but significant surface modification of the substrate is necessary for successful nanocrystalline diamond deposition and adhesion. A hybrid hard and tough material may be required for either the desired applications, or as a basis for nanocrystalline diamond film growth. One possibility is a composite system based on carbides or nitrides. Many binary carbides and nitrides offer one or more mentioned properties. By combining these binary compounds in a ternary or quaternary nanocrystalline system, we can tailor the material for a desired combination of properties. Here, we describe the results on the structural and mechanical properties of the coating systems composed of tungsten-chromium-carbide and/or nitride. These WC-Cr-(N) coatings are deposited using magnetron sputtering. The growth of adherent nanocrystalline diamond films by microwave plasma chemical vapor deposition has been demonstrated on these coatings. The WC-Cr-(N) and WC-Cr-(N)-NCD coatings are characterized with atomic force microscopy and SEM, X-ray diffraction, X-ray photoelectron spectroscopy, Raman spectroscopy, and nanoindentation.

Exogenous empirical-evidence equilibria in perfect-monitoring repeated games yield correlated equilibria

KAUST Repository

Dudebout, Nicolas; Shamma, Jeff S.

2014-01-01

This paper proves that exogenous empirical-evidence equilibria (xEEEs) in perfect-monitoring repeated games induce correlated equilibria of the associated one-shot game. An empirical-evidence equilibrium (EEE) is a solution concept for stochastic games. At equilibrium, agents' strategies are optimal with respect to models of their opponents. These models satisfy a consistency condition with respect to the actual behavior of the opponents. As such, EEEs replace the full-rationality requirement of Nash equilibria by a consistency-based bounded-rationality one. In this paper, the framework of empirical evidence is summarized, with an emphasis on perfect-monitoring repeated games. A less constraining notion of consistency is introduced. The fact that an xEEE in a perfect-monitoring repeated game induces a correlated equilibrium on the underlying one-shot game is proven. This result and the new notion of consistency are illustrated on the hawk-dove game. Finally, a method to build specific correlated equilibria from xEEEs is derived.

Exogenous empirical-evidence equilibria in perfect-monitoring repeated games yield correlated equilibria

KAUST Repository

Dudebout, Nicolas

2014-12-15

This paper proves that exogenous empirical-evidence equilibria (xEEEs) in perfect-monitoring repeated games induce correlated equilibria of the associated one-shot game. An empirical-evidence equilibrium (EEE) is a solution concept for stochastic games. At equilibrium, agents\\' strategies are optimal with respect to models of their opponents. These models satisfy a consistency condition with respect to the actual behavior of the opponents. As such, EEEs replace the full-rationality requirement of Nash equilibria by a consistency-based bounded-rationality one. In this paper, the framework of empirical evidence is summarized, with an emphasis on perfect-monitoring repeated games. A less constraining notion of consistency is introduced. The fact that an xEEE in a perfect-monitoring repeated game induces a correlated equilibrium on the underlying one-shot game is proven. This result and the new notion of consistency are illustrated on the hawk-dove game. Finally, a method to build specific correlated equilibria from xEEEs is derived.

Partial Cooperative Equilibria: Existence and Characterization

Directory of Open Access Journals (Sweden)

Amandine Ghintran

2010-09-01

Full Text Available We study the solution concepts of partial cooperative Cournot-Nash equilibria and partial cooperative Stackelberg equilibria. The partial cooperative Cournot-Nash equilibrium is axiomatically characterized by using notions of rationality, consistency and converse consistency with regard to reduced games. We also establish sufficient conditions for which partial cooperative Cournot-Nash equilibria and partial cooperative Stackelberg equilibria exist in supermodular games. Finally, we provide an application to strategic network formation where such solution concepts may be useful.

(Vapour + liquid) equilibria in the ternary system (acetonitrile + n-propanol + ethylene glycol) and corresponding binary systems at 101.3 kPa

International Nuclear Information System (INIS)

Qian, Guo-fei; Liu, Wen; Wang, Li-tao; Wang, Dao-cai; Song, Hang

2013-01-01

Highlights: • We adopted a new extractive solvent “ethylene glycol” to separate the mixture. • We measured the VLE data of binary system n-propanol + ethylene glycol. • We reinforce the VLE data of binary system acetonitrile + ethylene glycol. • We predicted the VLE data for the ternary system successfully. -- Abstract: Experimental isobaric (Vapour + liquid) equilibrium (VLE) data at 101.3 kPa were determined for three binary systems, viz. {acetonitrile (1) + n-propanol (2)}, {acetonitrile (1) + ethylene glycol (3)} and {n-propanol (2) + ethylene glycol (3)} and for one ternary system {acetonitrile (1) + n-propanol (2) + ethylene glycol (3)}. The measurements were performed using an improved Rose equilibrium still. The VLE data of the binary systems passed thermodynamic consistency tests and were correlated by Wilson and NRTL models. Good results were achieved. The phase behaviour of the ternary system was predicted directly by the parameters of two models obtained from the experimental binary results. The results showed an excellent agreement with experimental values

(Vapour + liquid) equilibria of ternary systems with ionic liquids using headspace gas chromatography

International Nuclear Information System (INIS)

Mokhtarani, Babak; Gmehling, Juergen

2010-01-01

(Vapour + liquid) equilibrium (VLE) data for the ternary systems (hexane + benzene), (hexane + cyclohexane), (benzene + cyclohexane), and (ethanol + water) with an ionic liquid as entrainer for extractive distillation were measured by headspace gas chromatography. As ionic liquids, 1-hexyl-3-methyl-imidazolium bis (trifluoromethyl-sulfonyl) imide [HMIM][BTI], 1-octyl-3-methyl-imidazolium bis (trifluoromethyl-sulfonyl) imide [OMIM][BTI], 1-octyl-3-methyl-imidazolium trifluoro-methanesulfonate [OMIM][OTF], and 1-butyl-3-methyl-imidazolium trifluoro-methanesulfonate [BMIM][OTF] were used. The experimental data show that the ionic liquids investigated have a great influence on the separation factors of the systems (hexane + benzene), (hexane + cyclohexane), and (benzene + cyclohexane). The experimental data were compared with the predicted results using mod. UNIFAC (Do). The predicted results are in good agreement with the experimental data.

(Vapour + liquid) equilibria of ternary systems with ionic liquids using headspace gas chromatography

Energy Technology Data Exchange (ETDEWEB)

Mokhtarani, Babak [Chemistry and Chemical Engineering Research Center of Iran, P.O. Box 14335-186, Tehran (Iran, Islamic Republic of); Gmehling, Juergen, E-mail: gmehling@tech.chem.uni-oldenburg.d [Carl von Ossietzky Universitaet Oldenburg, Technische Chemie, D-26111 Oldenburg (Germany)

2010-08-15

(Vapour + liquid) equilibrium (VLE) data for the ternary systems (hexane + benzene), (hexane + cyclohexane), (benzene + cyclohexane), and (ethanol + water) with an ionic liquid as entrainer for extractive distillation were measured by headspace gas chromatography. As ionic liquids, 1-hexyl-3-methyl-imidazolium bis (trifluoromethyl-sulfonyl) imide [HMIM][BTI], 1-octyl-3-methyl-imidazolium bis (trifluoromethyl-sulfonyl) imide [OMIM][BTI], 1-octyl-3-methyl-imidazolium trifluoro-methanesulfonate [OMIM][OTF], and 1-butyl-3-methyl-imidazolium trifluoro-methanesulfonate [BMIM][OTF] were used. The experimental data show that the ionic liquids investigated have a great influence on the separation factors of the systems (hexane + benzene), (hexane + cyclohexane), and (benzene + cyclohexane). The experimental data were compared with the predicted results using mod. UNIFAC (Do). The predicted results are in good agreement with the experimental data.

Experimental Investigation of the 1073 K (800 °C) Isothermal Section of the Al-V-Zr Ternary System

Science.gov (United States)

Zhu, Yude; Ouyang, Xuemei; Yin, Fucheng; Zhao, Manxiu; Lou, Jia

2018-03-01

This work is focused on an experimental investigation of the phase equilibria of the Al-V-Zr system at 1073 K (800 °C). The phase equilibria were analyzed using scanning electron microscopy (SEM) coupled with energy-dispersive spectrometry and X-ray diffraction. The results confirmed the presence of twelve three-phase regions and one ternary compound, Τ, which contains 10.0 to 16.5 at. pct Zr, 52.8 to 55.2 at. pct Al, and 29.3 to 36.3 at. pct V. The T phase can be in equilibrium with Al8V5, Al3Zr, Al2Zr, and α-V. The T phase belongs to the tetragonal crystal system with confirmed lattice parameters of a = 0.658531 nm and c = 0.517334 nm. The Al2Zr phase region is extraordinarily large and can be in equilibrium with all the compounds in the Al-Zr and V-Zr systems, with the exception of the AlZr phase.

Thermodynamics of the hydrogen-carbon-oxygen-tungsten system, as applied to the manufacture of tungsten and tungsten carbide

International Nuclear Information System (INIS)

Schwenke, G.K.

2001-01-01

The thermodynamics of the quaternary hydrogen-carbon oxygen-tungsten system and its binary and ternary sub-systems are reviewed. Published thermodynamic data are evaluated, and expression for free energies of formation are chosen. These expressions are integrated with and equilibrium-calculating algorithm, producing a powerful tool for understanding and improving the manufacture of tungsten and tungsten carbide. Three examples are presented: reduction/carburization of tungstic oxide with hydrogen, carbon, and methane. (author)

(Vapour + liquid) equilibria for binary and ternary mixtures of 2-propanol, tetrahydropyran, and 2,2,4-trimethylpentane at P = 101.3 kPa

International Nuclear Information System (INIS)

Lin, Dun-Yi; Tu, Chein-Hsiun

2012-01-01

Highlights: ► We report the VLE data at P = 101.3 kPa involving a cyclic ether. ► The activity coefficients of mixtures were obtained from modified Raoult’s law. ► The VLE data were correlated by four liquid activity coefficient models. ► The ternary VLE data were predicted from binary parameters of the four models. - Abstract: (Vapour + liquid) equilibrium (VLE) at P = 101.3 kPa have been determined for a ternary system (2-propanol + tetrahydropyran + 2,2,4-trimethylpentane) and its constituent binary systems (2-propanol + tetrahydropyran, 2-propanol + 2,2,4-trimethylpentane), and (tetrahydropyran + 2,2,4-trimethylpentane). Analysis of VLE data reveals that two binary systems (2-propanol + tetrahydropyran) and (2-propanol + 2,2,4-trimethylpentane) have a minimum boiling azeotrope. No azeotrope was found for the ternary system. The activity coefficients of liquid mixtures were obtained from the modified Raoult’s law and were used to calculate the reduced excess molar Gibbs free energy (g E /RT). Thermodynamic consistency tests were performed for all VLE data using the Van Ness direct test for the binary systems and the test of McDermott–Ellis as modified by Wisniak and Tamir for the ternary system. The VLE data of the binary mixtures were correlated using the three-suffix Margules, Wilson, NRTL, and UNIQUAC activity-coefficient models. The models with their best-fitted interaction parameters of the binary systems were used to predict the ternary (vapour + liquid) equilibrium.

Investigations of the ternary system beryllium-carbon-tungsten and analyses of beryllium on carbon surfaces; Untersuchung des ternaeren Systems Beryllium-Kohlenstoff-Wolfram und Betrachtungen von Beryllium auf Kohlenstoffoberflaechen

Energy Technology Data Exchange (ETDEWEB)

Kost, Florian

2009-05-25

Beryllium, carbon and tungsten are planned to be used as first wall materials in the future fusion reactor ITER. The aim of this work is a characterization of mixed material formation induced by thermal load. To this end, model systems (layers) were prepared and investigated, which give insight into the basic physical and chemical concepts. Before investigating ternary systems, the first step was to analyze the binary systems Be/C and Be/W (bottom-up approach), where the differences between the substrates PG (pyrolytic graphite) and HOPG (highly oriented pyrolytic graphite) were of special interest. Particularly X-ray photoelectron spectroscopy (XPS), low energy ion scattering (ISS) and Rutherford backscattering spectroscopy (RBS) were used as analysis methods. Beryllium evaporated on carbon shows an island growth mode, whereas a closed layer can be assumed for layer thicknesses above 0.7 nm. Annealing of the Be/C system induces Be{sub 2}C island formation for T{>=}770 K. At high temperatures (T{>=}1170 K), beryllium carbide dissociates, resulting in (metallic) beryllium desorption. For HOPG, carbide formation starts at higher temperatures compared to PG. Activation energies for the diffusion processes were determined by analyzing the decreasing beryllium amount versus annealing time. Surface morphologies were characterized using angle-resolved XPS (ARXPS) and atomic force microscopy (AFM). Experiments were performed to study processes in the Be/W system in the temperature range from 570 to 1270 K. Be{sub 2}W formation starts at 670 K, a complete loss of Be{sub 2}W is observed at 1170 K due to dissociation (and subsequent beryllium desorption). Regarding ternary systems, particularly Be/C/W and C/Be/W were investigated, attaching importance to layer thickness (reservoir) variations. At room temperature, Be{sub 2}C, W{sub 2}C, WC and Be{sub 2}W formation at the respective interfaces was observed. Further Be{sub 2}C is forming with increasing annealing temperatures

Ternary Weighted Function and Beurling Ternary Banach Algebra l1ω(S

Directory of Open Access Journals (Sweden)

Mehdi Dehghanian

2011-01-01

Full Text Available Let S be a ternary semigroup. In this paper, we introduce our notation and prove some elementary properties of a ternary weight function ω on S. Also, we make ternary weighted algebra l1ω(S and show that l1ω(S is a ternary Banach algebra.

Adsorption analysis equilibria and kinetics

CERN Document Server

Do, Duong D

1998-01-01

This book covers topics of equilibria and kinetics of adsorption in porous media. Fundamental equilibria and kinetics are dealt with for homogeneous as well as heterogeneous particles. Five chapters of the book deal with equilibria and eight chapters deal with kinetics. Single component as well as multicomponent systems are discussed. In kinetics analysis, we deal with the various mass transport processes and their interactions inside a porous particle. Conventional approaches as well as the new approach using Maxwell-Stefan equations are presented. Various methods to measure diffusivity, such

Quantum equilibria for macroscopic systems

International Nuclear Information System (INIS)

Grib, A; Khrennikov, A; Parfionov, G; Starkov, K

2006-01-01

Nash equilibria are found for some quantum games with particles with spin-1/2 for which two spin projections on different directions in space are measured. Examples of macroscopic games with the same equilibria are given. Mixed strategies for participants of these games are calculated using probability amplitudes according to the rules of quantum mechanics in spite of the macroscopic nature of the game and absence of Planck's constant. A possible role of quantum logical lattices for the existence of macroscopic quantum equilibria is discussed. Some examples for spin-1 cases are also considered

Ternary fission

International Nuclear Information System (INIS)

Wagemans, C.

1991-01-01

Since its discovery in 1946, light (charged) particle accompanied fission (ternary fission) has been extensively studied, for spontaneous as well as for induced fission reactions. The reason for this interest was twofold: the ternary particles being emitted in space and time close to the scission point were expected to supply information on the scission point configuration and the ternary fission process was an important source of helium, tritium, and hydrogen production in nuclear reactors, for which data were requested by the nuclear industry. Significant experimental progress has been realized with the advent of high-resolution detectors, powerful multiparameter data acquisition systems, and intense neutron and photon beams. As far as theory is concerned, the trajectory calculations (in which scission point parameters are deduced from the experimental observations) have been very much improved. An attempt was made to explain ternary particle emission in terms of a Plateau-Rayleigh hydrodynamical instability of a relatively long cylindrical neck or cylindrical nucleus. New results have also been obtained on the so-called open-quotes trueclose quotes ternary fission (fission in three about-equal fragments). The spontaneous emission of charged particles has also clearly been demonstrated in recent years. This chapter discusses the main characteristics of ternary fission, theoretical models, light particle emission probabilities, the dependence of the emission probabilities on experimental variables, light particle energy distributions, light particle angular distributions, correlations between light particle accompanied fission observables, open-quotes trueclose quotes ternary fission, and spontaneous emission of heavy ions. 143 refs., 18 figs., 8 tabs

Some stable hydromagnetic equilibria

Energy Technology Data Exchange (ETDEWEB)

Johnson, J L; Oberman, C R; Kulsrud, R M; Frieman, E A [Project Matterhorn, Princeton University, Princeton, NJ (United States)

1958-07-01

We have been able to find and investigate the properties of equilibria which are hydromagnetically stable. These equilibria can be obtained, for example, by wrapping conductors helically around the stellarator tube. Systems with I = 3 or 4 are indicated to be optimum for stability purposes. In some cases an admixture of I = 2 fields can be advantageous for achieving equilibrium. (author)

The experimental investigation of phase equilibria in the Al-rich corner within the ternary Al–Mn–Be system

Energy Technology Data Exchange (ETDEWEB)

Zupanič, Franc, E-mail: franc.zupanic@um.si [University of Maribor, Faculty of Mechanical Engineering, Smetanova ulica 17, SI-2000 Maribor (Slovenia); Markoli, Boštjan; Naglič, Iztok [University of Ljubljana, Faculty of Natural Sciences and Technologies, Askerceva 12, Ljubljana SI-1000 (Slovenia); Bončina, Tonica [University of Maribor, Faculty of Mechanical Engineering, Smetanova ulica 17, SI-2000 Maribor (Slovenia)

2013-09-05

Highlights: •We investigated the constitution of the Al-rich corner of the Al–Mn–Be system. •Be{sub 4}AlMn is a thermodynamically stable phase in the Al-corner of the Al–Mn–Be system. •The T-phase (Al{sub 15}Mn{sub 3}Be{sub 2}) is not a stable phase in the Al-corner at 600 °C. •The λ-Al{sub 4}Mn phase is a stable phase in the Al-corner at 600 °C. •T-phase is a stable phase at 750 °C. -- Abstract: This work investigated the constitution of the Al-rich corner within the ternary Al–Mn–Be phase diagram using SEM + EDS, AES, XRD and DSC. With respect to the results, an isothermal cross-section at 600 °C was established, as well as a prediction of the apparent liquidus projection in the Al-corner. Be{sub 4}AlMn is a thermodynamically stable phase in the Al-rich corner of the ternary phase diagram. The other ternary T-phase, usually designated as Al{sub 15}Mn{sub 3}Be{sub 2}, formed during solidification in alloys with Be:Mn atomic ratios of less than 4:1, and having more than 1.5 at.% Mn. This phase is not a stable phase in the Al-rich corner at 600 °C. In contrast, the λ-Al{sub 4}Mn phase is a stable one. The T-phase is stable over a rather large part of the phase diagram at least within a temperature range close to 750 °C, where it is in equilibrium with the Al-rich liquid phase, and Be{sub 4}AlMn.

Jump conditions in transonic equilibria

International Nuclear Information System (INIS)

Guazzotto, L.; Betti, R.; Jardin, S. C.

2013-01-01

In the present paper, the numerical calculation of transonic equilibria, first introduced with the FLOW code in Guazzotto et al.[Phys. Plasmas 11, 604 (2004)], is critically reviewed. In particular, the necessity and effect of imposing explicit jump conditions at the transonic discontinuity are investigated. It is found that “standard” (low-β, large aspect ratio) transonic equilibria satisfy the correct jump condition with very good approximation even if the jump condition is not explicitly imposed. On the other hand, it is also found that high-β, low aspect ratio equilibria require the correct jump condition to be explicitly imposed. Various numerical approaches are described to modify FLOW to include the jump condition. It is proved that the new methods converge to the correct solution even in extreme cases of very large β, while they agree with the results obtained with the old implementation of FLOW in lower-β equilibria.

Study of complex equilibria in niobium(V) and vanadium(V) systems with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol, tartrate and hydrogen peroxide using RP-HPLC

International Nuclear Information System (INIS)

Oszwaldowski, S.; Jarosz, M.

1997-01-01

Complex equilibria in multiligand niobium(V) systems with 2-(5-bromo-2-pyridilazo)-5-diethyl aminophenol (5-Br-PADAP), tartrate and hydrogen peroxide and vanadium(V) with 5-Br-PADP and tartrate were evaluated by reversed-phase high-performance liquid chromatography (RP-HPLC) using C 18 column and VIS detection at 590 nm. In Nb(V)-H 2 O 2 -tartrate-(5-Br P ADAP) system formation of multiligand niobium complex, non-reactive towards 5-Br-PADAP, was postulated. For V(V) system distribution of metal ion between V(V)-(5-Br-PADAP) binary and V(V)-tartrate-(5-Br-PADAP) ternary complexes were evaluated. On this base it was proved, that coloured ternary vanadium complex is only an intermediate stage in the formation of stable V(V)-tartrate binary complex. (author). 14 refs, 7 figs

(Liquid + liquid) equilibria of (water + linalool + limonene) ternary system at T = (298.15, 308.15, and 318.15) K

International Nuclear Information System (INIS)

Gramajo de Doz, Monica B.; Cases, Alicia M.; Solimo, Horacio N.

2008-01-01

(Liquid + liquid) equilibrium (LLE) data for {water (1) + linalool (2) + limonene (3)} ternary system at T = (298.15, 308.15, and 318.15 ± 0.05) K are reported. The organic chemicals were quantified by gas chromatography using a flame ionisation detector while water was quantified using a thermal conductivity detector. The effect of the temperature on (liquid + liquid) equilibrium is determined and discussed. Experimental data for the ternary mixture are compared with values calculated by the NRTL and UNIQUAC equations, and predicted by means of the UNIFAC group contribution method. It is found that the UNIQUAC and NRTL models provide a good correlation of the solubility curve at these three temperatures, while comparing the calculated values with the experimental ones, the best fit is obtained with the NRTL model. Finally, the UNIFAC model provides poor results, since it predicts a greater heterogeneous region than experimentally observed

Quantum equilibria for macroscopic systems

Energy Technology Data Exchange (ETDEWEB)

Grib, A [Department of Theoretical Physics and Astronomy, Russian State Pedagogical University, St. Petersburg (Russian Federation); Khrennikov, A [Centre for Mathematical Modelling in Physics and Cognitive Sciences Vaexjoe University (Sweden); Parfionov, G [Department of Mathematics, St. Petersburg State University of Economics and Finances (Russian Federation); Starkov, K [Department of Mathematics, St. Petersburg State University of Economics and Finances (Russian Federation)

2006-06-30

Nash equilibria are found for some quantum games with particles with spin-1/2 for which two spin projections on different directions in space are measured. Examples of macroscopic games with the same equilibria are given. Mixed strategies for participants of these games are calculated using probability amplitudes according to the rules of quantum mechanics in spite of the macroscopic nature of the game and absence of Planck's constant. A possible role of quantum logical lattices for the existence of macroscopic quantum equilibria is discussed. Some examples for spin-1 cases are also considered.

Thermodynamic studies of thorium carbide fuel preparation and fuel-clad comptability

International Nuclear Information System (INIS)

Besmann, T.M.; Beahm, E.C.

1979-01-01

The carbothermic reduction of thorium and uranium-thorium dioxide to monocarbide has been assessed. Equilibrium calculations have yielded Th-C-O and U-Th-C-O phase equilibria and (CO) pressures generated during reduction. The (CO) pressures were found to be at least five orders of magnitude greater than any of the other 15 gaseous species considered. This confirms that the monocarbide can successfully be prepared by carbothermic reduction. The chemical compatibility of thorium carbides with the Cr-Fe-Ni content of clad alloys has been thermodynamically avaluated. Solid solutions of 5 > and 5 > and of 7 C 3 > and 7 C 3 > were the principal reaction products. The Cr-Fe-Ni content of 316 stainless steel showed much less reaction product than that for any of the other six alloys considered. (orig.) [de

A tri-junction diffusion couple analysis of the Nb-Cr-Ti system at 950{degrees}C

Energy Technology Data Exchange (ETDEWEB)

Thoma, D.J. [Los Alamos National Lab., NM (United States); Perepezko, J.H. [Wisconsin Univ., Madison, WI (United States). Dept. of Materials Science and Engineering

1993-11-01

With a three-way diffusion couple consisting of a tri-junction between three elements, a whole spectrum of phase development and ternary equilibria is available within a single isothermal sample. Binary equilibria (for the three binary systems) are also available in single sample by analyzing diffusion zones at composition limits outside the field of ternary interaction. The tri-junction approach was employed to evaluate ternary phase formation, ternary solubility limits of binary phases, and diffusion paths in a candidate high-temperature structural system (Nb-Cr-Ti). Ternary phase equilibria and tie lines have been defined at 950C and results confirmed with isothermal anneals of two-phase ternary alloys. The continuous solubility in TiCr{sub 2}-NbCr{sub 2} region is broadened by at least 5 at. % from binary intermetallic phase fields. No new ternary phases were detected in the Nb-CrTi system at 950C. By examining the relative shifts in the diffusion interfaces, a qualitative ranking of interdiffusion suggests that addition of Nb restricts diffusion of Cr into Ti compared to binary (Cr/Ti) behavior.

Pierce instability and bifurcating equilibria

International Nuclear Information System (INIS)

Godfrey, B.B.

1981-01-01

The report investigates the connection between equilibrium bifurcations and occurrence of the Pierce instability. Electrons flowing from one ground plane to a second through an ion background possess a countable infinity of static equilibria, of which only one is uniform and force-free. Degeneracy of the uniform and simplest non-uniform equilibria at a certain ground plan separation marks the onset of the Pierce instability, based on a newly derived dispersion relation appropriate to all the equilibria. For large ground plane separations the uniform equilibrium is unstable and the non-uniform equilibrium is stable, the reverse of their stability properties at small separations. Onset of the Pierce instability at the first bifurcation of equilibria persists in more complicated geometries, providing a general criterion for marginal stability. It seems probable that bifurcation analysis can be a useful tool in the overall study of stable beam generation in diodes and transport in finite cavities

Experimental Investigation and Thermodynamic Assessment of Phase Equilibria in the PLLA/Dioxane/Water Ternary System for Applications in the Biomedical Field.

Science.gov (United States)

Ruggiero, Flavia; Netti, Paolo Antonio; Torino, Enza

2015-12-01

Fundamental understanding of thermodynamic of phase separation plays a key role in tuning the desired features of biomedical devices. In particular, phase separation of ternary solution is of remarkable interest in processes to obtain biodegradable and biocompatible architectures applied as artificial devices to repair, replace, or support damaged tissues or organs. In these perspectives, thermally induced phase separation (TIPS) is the most widely used technique to obtained porous morphologies and, in addition, among different ternary systems, polylactic acid (PLLA)/dioxane/water has given promising results and has been largely studied. However, to increase the control of TIPS-based processes and architectures, an investigation of the basic energetic phenomena occurring during phase separation is still required. Here we propose an experimental investigation of the selected ternary system by using isothermal titration calorimetric approach at different solvent/antisolvent ratio and a thermodynamic explanation related to the polymer-solvents interactions in terms of energetic contribution to the phase separation process. Furthermore, relevant information about the phase diagrams and interaction parameters of the studied systems are furnished in terms of liquid-liquid miscibility gap. Indeed, polymer-solvents interactions are responsible for the mechanism of the phase separation process and, therefore, of the final features of the morphologies; the knowledge of such data is fundamental to control processes for the production of membranes, scaffolds and several nanostructures. The behavior of the polymer at different solvent/nonsolvent ratios is discussed in terms of solvation mechanism and a preliminary contribution to the understanding of the role of the hydrogen bonding in the interface phenomena is also reported. It is the first time that thermodynamic data of a ternary system are collected by mean of nano-isothermal titration calorimetry (nano-ITC). Supporting

Axisymmetric ideal magnetohydrodynamic equilibria with incompressible flows

International Nuclear Information System (INIS)

Tasso, H.; Throumoulopoulos, G.N.

1997-12-01

It is shown that the ideal MHD equilibrium states of an axisymmetric plasma with incompressible flows are governed by an elliptic partial differential equation for the poloidal magnetic flux function ψ containing five surface quantities along with a relation for the pressure. Exact equilibria are constructed including those with non vanishing poloidal and toroidal flows and differentially varying radial electric fields. Unlike the case in cylindrical incompressible equilibria with isothermal magnetic surfaces which should have necessarily circular cross sections [G. N. Throumoulopoulos and H. Tasso, Phys. Plasmas 4, 1492 (1997)], no restriction appears on the shapes of the magnetic surfaces in the corresponding axisymmetric equilibria. The latter equilibria satisfy a set of six ordinary differential equations which for flows parallel to the magnetic field B can be solved semianalytically. In addition, it is proved the non existence of incompressible axisymmetric equilibria with (a) purely poloidal flows and (b) non-parallel flows with isothermal magnetic surfaces and vertical stroke B vertical stroke = vertical stroke B vertical stroke (ψ) (omnigenous equilibria). (orig.)

Peculiarity of component interaction in {l_brace}Y, Dy{r_brace}-Mn-Sn ternary systems

Energy Technology Data Exchange (ETDEWEB)

Romaka, V.V. [Department of Materials Engineering and Applied Physics, Lviv Polytechnic National University, Ustyyanovycha Str. 5, 79013 Lviv (Ukraine); Konyk, M. [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya Str. 6, 79005 Lviv (Ukraine); Romaka, L., E-mail: romakal@franko.lviv.ua [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya Str. 6, 79005 Lviv (Ukraine); Pavlyuk, V. [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya Str. 6, 79005 Lviv (Ukraine); Jan Dlugosz University, Institute of Chemistry, Environmental Protection and Biotechnology, al. Armii Krajowej 13/15, 42200 Czestochowa (Poland); Ehrenberg, H. [Institute for Complex Materials, IFW Dresden, Helmholtzstrasse 20, D-01069 Dresden (Germany); Tkachuk, A. [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya Str. 6, 79005 Lviv (Ukraine)

2011-07-14

Highlights: > {l_brace}Y, Dy{r_brace}-Mn-Sn ternary systems at 770 K are characterized by formation of stannides with general compositions RMn{sub 6}Sn{sub 6} and R{sub 4}Mn{sub 4}Sn{sub 7}. > The crystal structure of YMn{sub 6}Sn{sub 6} was determined by single crystal and powder diffraction methods. > Structural analysis showed that Dy{sub 4}Mn{sub 4}Sn{sub 7} compound is disordered. > Isostructural R{sub 4}Mn{sub 4}Sn{sub 7} compounds were also found with Gd, Tb, Ho, Er, Tm(confirmed), Yb, and Lu. - Abstract: The phase equilibria in the Y-Mn-Sn and Dy-Mn-Sn ternary systems were studied at 770 K by means of X-ray and metallographic analyses in the whole concentration range. Both Y-Mn-Sn and Dy-Mn-Sn systems are characterized by formation of two ternary compounds RMn{sub 6}Sn{sub 6} (MgFe{sub 6}Ge{sub 6}-type, space group P6/mmm) and R{sub 4}Mn{sub 4}Sn{sub 7} (Zr{sub 4}Co{sub 4}Ge{sub 7}-type, space group I4/mmm). The disorder in Dy{sub 4}Mn{sub 4}Sn{sub 7} compound was found by single crystal method. Compounds with the same type of structure were also found with Gd, Tb, Ho, Er, Tm (confirmed), Yb, and Lu and their lattice parameters were determined.

Insight into partial agonism by observing multiple equilibria for ligand-bound and Gs-mimetic nanobody-bound β1-adrenergic receptor.

Science.gov (United States)

Solt, Andras S; Bostock, Mark J; Shrestha, Binesh; Kumar, Prashant; Warne, Tony; Tate, Christopher G; Nietlispach, Daniel

2017-11-27

A complex conformational energy landscape determines G-protein-coupled receptor (GPCR) signalling via intracellular binding partners (IBPs), e.g., G s and β-arrestin. Using 13 C methyl methionine NMR for the β 1 -adrenergic receptor, we identify ligand efficacy-dependent equilibria between an inactive and pre-active state and, in complex with G s -mimetic nanobody, between more and less active ternary complexes. Formation of a basal activity complex through ligand-free nanobody-receptor interaction reveals structural differences on the cytoplasmic receptor side compared to the full agonist-bound nanobody-coupled form, suggesting that ligand-induced variations in G-protein interaction underpin partial agonism. Significant differences in receptor dynamics are observed ranging from rigid nanobody-coupled states to extensive μs-to-ms timescale dynamics when bound to a full agonist. We suggest that the mobility of the full agonist-bound form primes the GPCR to couple to IBPs. On formation of the ternary complex, ligand efficacy determines the quality of the interaction between the rigidified receptor and an IBP and consequently the signalling level.

Tungsten carbide and tungsten-molybdenum carbides as automobile exhaust catalysts

International Nuclear Information System (INIS)

Leclercq, L.; Daubrege, F.; Gengembre, L.; Leclercq, G.; Prigent, M.

1987-01-01

Several catalyst samples of tungsten carbide and W, Mo mixed carbides with different Mo/W atom ratios, have been prepared to test their ability to remove carbon monoxide, nitric oxide and propane from a synthetic exhaust gas simulating automobile emissions. Surface characterization of the catalysts has been performed by X-ray photoelectron spectroscopy (XPS) and selective chemisorption of hydrogen and carbon monoxide. Tungsten carbide exhibits good activity for CO and NO conversion, compared to a standard three-way catalyst based on Pt and Rh. However, this W carbide is ineffective in the oxidation of propane. The Mo,W mixed carbides are markedly different having only a very low activity. 9 refs.; 10 figs.; 5 tabs

Experimental Investigation of Phase Equilibria in the Ho-Ti-Si Ternary System at 973 K (700 °C)

Science.gov (United States)

Han, Feng; Zhan, Yongzhong

2018-02-01

Phase equilibrium relations of the Ho-Ti-Si ternary system at 973 K (700 °C) were experimentally researched by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive spectrometer (EDS). The isothermal section of the system at 973 K (700 °C) consists of 14 three-phase regions, 27 two-phase regions, and 14 single-phase regions. The phases Ti5Si3, Ti5Si4, TiSi, TiSi2, Ho5Si3, Ho5Si4, HoSi, αHoSi2-b, and βHoSi2-a are proved to exist at 973 K (700 °C). Previously reported HoTiSi and Ho2Ti3Si4 ternary compounds were confirmed to exist at this temperature. The solubility of Ho in the intermediate phases (i.e., TiSi2, TiSi, Ti5Si4, and Ti5Si3) at the Ti-Si side is extremely small. The maximum solubilities of Ti in HoSi2-b, Ho5Si4, and Ho5Si3 are confirmed to be 8.0, 7.2, and 6.0 at. pct, respectively.

The calculation of phase equilibria of oxide core-concrete systems

International Nuclear Information System (INIS)

Ball, R.G.J.; Mignanelli, M.A.; Barry, T.I.; Gisby, J.A.

1993-01-01

Thermodynamic models have been developed to describe the phase equilibria of oxide solutions appropriate for the understanding of the chemical interactions between nuclear reactor core debris and concrete. For this purpose, the Gibbs energy of the liquid phase is described by the inclusion of associate species and nonideal interactions between the components and associate species. Assessments of the thermodynamic and phase equilibrium data for the subsystems of the CaO-Al 2 O 3 -SiO 2 -UO 2 -ZrO 2 system have been used to obtain a thermodynamic description of the crystalline and liquid phases in good agreement with published data. The data for the subsystems have then been combined, using well established principles, to predict the phase relationships in the ternary and quaternary sytsems and in the overall quinary system. The results show that he overall system cannot properly be treated as a pseudo-ideal liquid and solid solution, as used in some computer codes which attempt to model the physics and chemistry of core-concrete interactions. The limitations of the current model are discussed. (orig.)

Multiple equilibria of divertor plasmas

International Nuclear Information System (INIS)

Vu, H.X.; Prinja, A.K.

1993-01-01

A one-dimensional, two-fluid transport model with a temperature-dependent neutral recycling coefficient is shown to give rise to multiple equilibria of divertor plasmas (bifurcation). Numerical techniques for obtaining these multiple equilibria and for examining their stability are presented. Although these numerical techniques have been well known to the scientific community, this is the first time they have been applied to divertor plasma modeling to show the existence of multiple equilibria as well as the stability of these solutions. Numerical and approximate analytical solutions of the present one-dimensional transport model both indicate that there exists three steady-state solutions corresponding to (1) a high-temperature, low-density equilibrium, (2) a low-temperature, high-density equilibrium, and (3) an intermediate-temperature equilibrium. While both the low-temperature and the high-temperature equilibria are stable, with respect to small perturbations in the plasma conditions, the intermediate-temperature equilibrium is physically unstable, i.e., any small perturbation about this equilibrium will cause a transition toward either the high-temperature or low-temperature equilibrium

Phase equilibria and stability of the B2 phase in the Ni-Mn-Al and Co-Mn-Al systems

International Nuclear Information System (INIS)

Kainuma, R.; Ise, M.; Ishikawa, K.; Ohnuma, I.; Ishida, K.

1998-01-01

The phase equilibria and ordering reactions in the composition region up to 50 at.% Al have been investigated in the Ni-Mn-Al and Co-Mn-Al systems at temperatures in the interval 850-1200 C mainly by the diffusion couple method. The compositions of the γ (A1: fcc-Ni, -Co, γ-Mn), γ' (L1 2 : Ni 3 Al), β (B2: NiAl, CoAl, NiMn), β-Mn (A13: β-Mn type), δ-Mn (A2: bcc-Mn) and ε (A3: hcp-(Mn, Al)) phases in equilibrium and the critical boundaries of the A2/B2 continuous ordering transition in the bcc phase region have been determined. It is shown that in the Mn-rich portion of the ternary systems both continuous and discontinuous A2 to B2 ordering transitions exist. The A2+B2 two-phase region in the isothermal sections has a lenticular shape and exists over a wide temperature range. The phase equilibria between the γ, γ', β, β-Mn, δ-Mn and ε phases are presented and the stability of the ordered bcc aluminides is discussed. (orig.)

Experimental Phase Equilibria Studies of the Pb-Fe-O System in Air, in Equilibrium with Metallic Lead and at Intermediate Oxygen Potentials

Science.gov (United States)

Shevchenko, M.; Jak, E.

2017-12-01

The phase equilibria information on the Pb-Fe-O system is of practical importance for the improvement of the existing thermodynamic database of lead-containing slag systems (Pb-Zn-Fe-Cu-Si-Ca-Al-Mg-O). Phase equilibria of the Pb-Fe-O system have been investigated: (a) in air at temperatures between 1053 K and 1373 K (780 °C and 1100 °C); (b) in equilibrium with metallic lead at temperatures between 1053 K and 1373 K (780 °C and 1100 °C); and (c) at intermediate oxidation conditions for the liquid slag in equilibrium with two solids (spinel + magnetoplumbite), at temperatures between 1093 K and 1373 K (820 °C and 1100 °C). The high-temperature equilibration/quenching/electron probe X-ray microanalysis technique has been used to accurately determine the compositions of the phases in equilibrium in the system. The Pb and Fe concentrations in the phases were determined directly; preliminary thermodynamic modeling with FactSage was used to estimate the ferrous-to-ferric ratios and to present the results in the ternary diagram.

Corrosion resistant cemented carbide

International Nuclear Information System (INIS)

Hong, J.

1990-01-01

This paper describes a corrosion resistant cemented carbide composite. It comprises: a granular tungsten carbide phase, a semi-continuous solid solution carbide phase extending closely adjacent at least a portion of the grains of tungsten carbide for enhancing corrosion resistance, and a substantially continuous metal binder phase. The cemented carbide composite consisting essentially of an effective amount of an anti-corrosion additive, from about 4 to about 16 percent by weight metal binder phase, and with the remaining portion being from about 84 to about 96 percent by weight metal carbide wherein the metal carbide consists essentially of from about 4 to about 30 percent by weight of a transition metal carbide or mixtures thereof selected from Group IVB and of the Periodic Table of Elements and from about 70 to about 96 percent tungsten carbide. The metal binder phase consists essentially of nickel and from about 10 to about 25 percent by weight chromium, the effective amount of an anti-corrosion additive being selected from the group consisting essentially of copper, silver, tine and combinations thereof

The Al-rich region of the Al-Mn-Ni alloy system. Part II. Phase equilibria at 620-1000 oC

International Nuclear Information System (INIS)

Balanetskyy, S.; Meisterernst, G.; Grushko, B.; Feuerbacher, M.

2011-01-01

Research highlights: → Phase equilibria in the Al-rich region of the Al-Mn-Ni alloy system were studied at 1000, 950, 850, 750, 700, 645 and 620 deg. C by means of SEM, TEM, powder XRD and DTA. → Three ternary thermodynamically stable intermetallics, the φ-phase (Al 5 Co 2 -type, hP26, P63/mmc; a = 0.76632(16), c = 0.78296(15) nm), the κ-phase (κ-Al 14.4 Cr 3.4 Ni l.1 -type, hP227, P63/m; a = 1.7625(10), c = 1.2516(10) nm), and the O-phase (O-Al 77 Cr 14 Pd 9 -type, Pmmn, oP650,: a = 2.3316(16), b = 1.2424(15), c = 3.2648(14) nm), as well as three ternary metastable phases, the decagonal D 3 -phase with periodicity about 1.25 nm, the Al 9 (Mn,Ni) 2 -phase (Al 9 Co 2 -type, P1121/a, mP22; a = 0.8585(16), b = 0.6269(9), c = 0.6205(11) nm, β = 95.34(10) o ) and the O 1 -phase (basecentered orthorhombic, a ∼ 23.8, b ∼ 12.4, c ∼ 32.2 nm) were revealed. → The existence of a thermodynamically stable R-phase of stoichiometry Al 60 Mn 11 Ni 4 , reported earlier in literature, was not confirmed in the present study. - Abstract: Phase equilibria in the Al-rich region of the Al-Mn-Ni alloy system were studied at 1000, 950, 850, 750, 700, 645 and 620 o C. Three ternary thermodynamically stable intermetallics, the φ-phase (Al 5 Co 2 -type, hP26, P6 3 /mmc; a = 0.76632(16), c = 0.78296(15) nm), the κ-phase (κ-Al 14.4 Cr 3.4 Ni l.1 -type, hP227, P6 3 /m; a = 1.7625(10), c = 1.2516(10) nm), and the O-phase (O-Al 77 Cr 14 Pd 9 -type, Pmmn, oP650,: a = 2.3316(16), b = 1.2424(15), c = 3.2648(14) nm), as well as three ternary metastable phases, the decagonal D 3 -phase with periodicity about 1.25 nm, the Al 9 (Mn,Ni) 2 -phase (Al 9 Co 2 -type, P112 1 /a, mP22; a = 0.8585(16), b = 0.6269(9), c = 0.6205(11) nm, β = 95.34(10) o ) and the O 1 -phase (base-centered orthorhombic, a ∼ 23.8, b ∼ 12.4, c ∼ 32.2 nm) were revealed. Their physicochemical behaviour in the Al-Mn-Ni alloy system was studied.

Ternary fission

Indian Academy of Sciences (India)

the energy minimization of all possible ternary breakups of a heavy radioactive nucleus. Further, within the TCM we have analysed the competition between different geometries as well as different positioning of the fragments. Also, an attempt was made to calculate the mass distribution of ternary fission process within the ...

Phase equilibria basic principles, applications, experimental techniques

CERN Document Server

Reisman, Arnold

2013-01-01

Phase Equilibria: Basic Principles, Applications, Experimental Techniques presents an analytical treatment in the study of the theories and principles of phase equilibria. The book is organized to afford a deep and thorough understanding of such subjects as the method of species model systems; condensed phase-vapor phase equilibria and vapor transport reactions; zone refining techniques; and nonstoichiometry. Physicists, physical chemists, engineers, and materials scientists will find the book a good reference material.

Monosilicide-disilicide-silicon phase equilibria in the nickel-platinum-silicon and nickel-palladium-silicon systems

Science.gov (United States)

Loomans, M. E.; Chi, D. Z.; Chua, S. J.

2004-10-01

Bulk-phase equilibria in Ni-rich/Si-rich alloys of the Ni-Pt-Si and Ni-Pd-Si systems were investigated. Results suggest that a bulk monosilicide solid solution, containing up to at least 11 at. pct Pt, exists in the Ni-Pt-Si system. Monosilicides containing more than 11 at. pct Pt were not examined. Results from both ternary systems point convincingly to the existence of a NiSi+Si↔NiSi2 eutectoid reaction near 700 °C in the Ni-Si binary system; data from the Ni-Pt-Si system, which yield the more accurate determination of the eutectoid temperature, place it at roughly 710 °C. The Pt and Pd concentrations of monosilicide in equilibrium with disilicide and Si were measured using energy-dispersive spectrometry (EDS) and were found to increase with temperature.

Effect of mono-, di- and tri-ethanolammonium tetrafluoroborate protonic ionic liquids on vapour liquid equilibria of ethanol aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Shen Chong [State Key Laboratory of Chemical Resource Engineering and College of Chemical Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Ma Xiaoyan [College of Science, Beijing University of Chemical Technology, Beijing 100029 (China); Lu Yingzhou [State Key Laboratory of Chemical Resource Engineering and College of Chemical Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Li Chunxi, E-mail: Licx@mail.buct.edu.c [State Key Laboratory of Chemical Resource Engineering and College of Chemical Engineering, Beijing University of Chemical Technology, Beijing 100029 (China)

2011-03-15

Vapour pressures were measured using a quasi-static ebulliometer for the binary mixture of (water + ethanol) containing one of three protonic ionic liquids (PIL), namely, mono-, di- or tri-ethanolammonium tetrafluoroborate, over the temperature range of (318.24 to 356.58) K at fixed PIL content of 0.30 in mass fraction. The vapour pressure data of the PIL-containing ternary systems were correlated using the NRTL equation with an overall root mean square deviation (RMSD) of 0.0092. The regressed NRTL parameters were used to predict the isobaric vapour liquid equilibria (VLE) for ternary systems (water + ethanol + PIL) at varying mass fraction of PIL and atmospheric pressure (101.3 kPa). It is shown that the effect of PILs on the VLE of the (water + ethanol) mixture follows the order: [HTEA][BF{sub 4}] > [HDEA][BF{sub 4}] > [HMEA][BF{sub 4}]. In addition, the relative volatilities of ethanol to water for pseudo-binary systems (water + ethanol + PIL) were calculated. The results indicate that the PILs studied can enhance the relative volatility of ethanol to water and even break the azeotropic behaviour of ethanol aqueous solution when PIL content is increased to a specified content.

Phase equilibria in the Zr-Si-B ternary system (Zr-Si-ZrB{sub 2} region) at 1 173 K

Energy Technology Data Exchange (ETDEWEB)

Han, Feng; Luo, Hao [Guangxi Univ., Nanning (China). College of Materials Science and Engineering; Guangxi Univ., Nanning (China). Guangxi Key Lab. of Processing for Non-ferrous Metal and Featured Materials; Zhan, Yongzhong [Guangxi Univ., Nanning (China). College of Materials Science and Engineering; Guangxi Univ., Nanning (China). Guangxi Key Lab. of Processing for Non-ferrous Metal and Featured Materials; Guangxi Univ., Nanning (China). Center of Ecological Collaborative Innovation for Aluminum Industry

2017-10-15

The isothermal section of the Zr-Si-B ternary system (Zr-Si-ZrB{sub 2} region) at 1 173 K has been experimentally determined. All equilibrated alloys were characterized via X-ray powder diffraction and scanning electron microscopy equipped with energy-dispersive X-ray analysis. A ternary phase Zr{sub 5}(Si{sub 0.86}B{sub 0.14}){sub 3} was found at 1 173 K. The experimental results show that the isothermal section consists of 11 single-phase regions, 26 two-phase regions and 13 three-phase regions. The existence of eight compounds, i.e. ZrSi{sub 2}, ZrSi, Zr{sub 5}Si{sub 4}, Zr{sub 3}Si{sub 2}, Zr{sub 2}Si, ZrB, ZrB{sub 2} and Zr{sub 5}(Si{sub 0.86}B{sub 0.14}){sub 3} in this system has been confirmed in the Zr-Si-ZrB{sub 2} region at 1 173 K.

Neoclassical MHD equilibria with ohmic current

International Nuclear Information System (INIS)

Tokuda, Shinji; Takeda, Tatsuoki; Okamoto, Masao.

1989-01-01

MHD equilibria of tokamak plasmas with neoclassical current effects (neoclassical conductivity and bootstrap current) were calculated self-consistently. Neoclassical effects on JFT-2M tokamak plasmas, sustained by ohmic currents, were studied. Bootstrap currents flow little for L-mode type equilibria because of low attainable values of poloidal beta, β J . H-mode type equilibria give bootstrap currents of 30% ohmic currents for β J attained by JFT-2M and 100% for β J ≥ 1.5, both of which are sufficient to change the current profiles and the resultant MHD equilibria. Neoclassical conductivity which has roughly half value of the classical Spitzer conductivity brings peaked ohmic current profiles to yield low safety factor at the magnetic axis. Neoclassical conductivity reduces the value of effective Z(Z eff ) which is necessary to give the observed one-turn voltage but it needs impurities accumulating at the center when such peaked current profiles are not observed. (author)

Prediction of thermophysical and transport properties of ternary organic non-electrolyte systems including water by polynomials

Directory of Open Access Journals (Sweden)

Đorđević Bojan D.

2013-01-01

Full Text Available The description and prediction of the thermophysical and transport properties of ternary organic non-electrolyte systems including water by the polynomial equations are reviewed. Empirical equations of Radojković et al. (also known as Redlich-Kister, Kohler, Jacob-Fitzner, Colinet, Tsao-Smith, Toop, Scatchard et al. and Rastogi et al. are compared with experimental data of available papers appeared in well know international journals (Fluid Phase Equilibria, Journal of Chemical and Engineering Data, Journal of Chemical Thermodynamics, Journal of Solution Chemistry, Journal of the Serbian Chemical Society, The Canadian Journal of Chemical Engineering, Journal of Molecular Liquids, Thermochimica Acta, etc.. The applicability of empirical models to estimate excess molar volumes, VE, excess viscosities, ηE, excess free energies of activation of a viscous flow,

Learning to Play Efficient Coarse Correlated Equilibria

KAUST Repository

Borowski, Holly P.; Marden, Jason R.; Shamma, Jeff S.

2018-01-01

The majority of the distributed learning literature focuses on convergence to Nash equilibria. Coarse correlated equilibria, on the other hand, can often characterize more efficient collective behavior than even the best Nash equilibrium. However

Balancing Accuracy and Computational Efficiency for Ternary Gas Hydrate Systems

Science.gov (United States)

White, M. D.

2011-12-01

phase transitions. This paper describes and demonstrates a numerical solution scheme for ternary hydrate systems that seeks a balance between accuracy and computational efficiency. This scheme uses a generalize cubic equation of state, functional forms for the hydrate equilibria and cage occupancies, variable switching scheme for phase transitions, and kinetic exchange of hydrate formers (i.e., CH4, CO2, and N2) between the mobile phases (i.e., aqueous, liquid CO2, and gas) and hydrate phase. Accuracy of the scheme will be evaluated by comparing property values and phase equilibria against experimental data. Computational efficiency of the scheme will be evaluated by comparing the base scheme against variants. The application of interest will the production of a natural gas hydrate deposit from a geologic formation, using the guest molecule exchange process; where, a mixture of CO2 and N2 are injected into the formation. During the guest-molecule exchange, CO2 and N2 will predominately replace CH4 in the large and small cages of the sI structure, respectively.

Ternary chalcopyrite semiconductors

CERN Document Server

Shay, J L; Pamplin, B R

2013-01-01

Ternary Chalcopyrite Semiconductors: Growth, Electronic Properties, and Applications covers the developments of work in the I-III-VI2 and II-IV-V2 ternary chalcopyrite compounds. This book is composed of eight chapters that focus on the crystal growth, characterization, and applications of these compounds to optical communications systems. After briefly dealing with the status of ternary chalcopyrite compounds, this book goes on describing the crystal growth of II-IV-V2 and I-III-VI2 single crystals. Chapters 3 and 4 examine the energy band structure of these semiconductor compounds, illustrat

Peculiarities of component interaction in {Gd, Er}-V-Sn Ternary systems at 870 K and crystal structure of RV6Sn6 stannides

International Nuclear Information System (INIS)

Romaka, L.; Stadnyk, Yu.; Romaka, V.V.; Demchenko, P.; Stadnyshyn, M.; Konyk, M.

2011-01-01

Highlights: → {Gd, Er}-V-Sn ternary systems at 870 K are characterized by formation of stannides with general compositions RV 6 Sn 6 . → Isostructural RV 6 Sn 6 compounds were also found with Y, Dy, Ho, Tm, and Lu. → The crystal structure of RV 6 Sn 6 compounds was determined by powder diffraction method. → Structural analysis showed that RV 6 Sn 6 compounds (R = Gd, Dy-Tm, Lu) are disordered; YV 6 Sn 6 is characterized by structure ordering. - Abstract: The phase equilibria in the Gd-V-Sn and Er-V-Sn ternary systems were studied at 870 K by means of X-ray and metallographic analyses in the whole concentration range. Both Gd-V-Sn and Er-V-Sn systems are characterized by formation of one ternary compound at investigated temperature, with stoichiometry RV 6 Sn 6 (SmMn 6 Sn 6 -type, space group P6/mmm, a = 0.55322(3) nm, c = 0.91949(7) nm for Gd, a = 0.55191(2) nm, c = 0.91869(8) nm for Er). Solubility of the third component in the binary compounds was not observed. Compounds with the SmMn 6 Sn 6 -type were also found with Dy, Ho, Tm, and Lu, while YV 6 Sn 6 compound crystallizes in HfFe 6 Ge 6 structure type. All investigated compounds are the first ternary stannides with rare earth elements and vanadium.

Low alloy steels that minimize the hydrogen-carbide reaction. Final technical report, October 1, 1978-September 30, 1979. Part I

Energy Technology Data Exchange (ETDEWEB)

Kar, R. J.; Parker, E. R.; Zackay, V. F.

1979-01-01

This report presents results obtained during the first year of a research program to investigate important metallurgical parameters that control the reactions of hydrogen with carbides in steels. Preliminary work included a detailed literature review of th phenomenon of decarburization and methane bubble formation in steels and a suitable experimental technique for investigating hydrogen attack in laboratory conditions was established. Detailed microstructural-mechanical property evaluations were carried out on two series of alloys; the first was based on a plain carbon steel to which binary and ternary alloy additions were made to vary the carbide structure and morphology and assess these effects on the observed hydrogen attack resistance. The second group of steels consisted of commercial Mn-Mo-Ni (A 533 B) and Cr-Mo (A 542 type) steels and their alloy modifications, with a view towards developing steels with improved hydrogen attack resistance.

Learning to Play Efficient Coarse Correlated Equilibria

KAUST Repository

Borowski, Holly P.

2018-03-10

The majority of the distributed learning literature focuses on convergence to Nash equilibria. Coarse correlated equilibria, on the other hand, can often characterize more efficient collective behavior than even the best Nash equilibrium. However, there are no existing distributed learning algorithms that converge to specific coarse correlated equilibria. In this paper, we provide one such algorithm, which guarantees that the agents’ collective joint strategy will constitute an efficient coarse correlated equilibrium with high probability. The key to attaining efficient correlated behavior through distributed learning involves incorporating a common random signal into the learning environment.

Multiple Equilibria in Noisy Rational Expectations Economies

DEFF Research Database (Denmark)

Pálvölgyi, Dömötör; Venter, Gyuri

with a continuous price function. However, we also construct a tractable class of equilibria with discontinuous prices that have very different economic implications, including (i) jumps and crashes, (ii) significant revisions in uninformed belief due to small changes in the market price, (iii) “upward......-sloping” demand curves, (iv) higher prices leading to future returns that are higher in expectation (price drift) and (v) more positively skewed. Discontinuous equilibria can be arbitrarily close to being fully-revealing. Finally, discontinuous equilibria with the same construction also exist in Hellwig (1980)....

High-pressure fluid-phase equilibria: Experimental methods and systems investigated (2000-2004)

DEFF Research Database (Denmark)

Dohrn, Ralf; Peper, Stephanie; Fonseca, José

2010-01-01

As a part of a series of reviews, a compilation of systems for which high-pressure phase-equilibrium data were published between 2000 and 2004 is given. Vapor-liquid equilibria, liquid-liquid equilibria, vapor-liquid-liquid equilibria,solid-liquid equilibria, solid-vapor equilibria, solid-vapor-l...

Stability of relative equilibria of three vortices

DEFF Research Database (Denmark)

Aref, Hassan

2009-01-01

Three point vortices on the unbounded plane have relative equilibria wherein the vortices either form an equilateral triangle or are collinear. While the stability analysis of the equilateral triangle configurations is straightforward, that of the collinear relative equilibria is considerably mor...

Liquid-liquid equilibria for binary and ternary systems containing glycols, aromatic hydrocarbons, and water: Experimental measurements and modeling with the CPA EoS

DEFF Research Database (Denmark)

Folas, Georgios; Kontogeorgis, Georgios; Michelsen, Michael Locht

2006-01-01

Liquid-liquid equilibrium data of four binary glycol + aromatic hydrocarbon systems and three ternary systems containing water have been measured at atmospheric pressure. The measured systems are monoethylene glycol (MEG) + benzene or toluene, triethylene glycol (TEG) + benzene or toluene, MEG...... + water + benzene, MEG + water + toluene, and TEG + water + toluene. The binary systems are correlated with the Cubic-Plus-Association (CPA) equation of state while the ternary systems are predicted from interaction parameters obtained from the binary systems. Very satisfactory liquid-liquid equilibrium...... correlations are obtained for the binary systems using temperature-independent interaction parameters, while adequate predictions are achieved for multicomponent water + glycol + aromatic hydrocarbons systems when accounting for the solvation between the aromatic hydrocarbons and glycols or water....

Design and Performance of Property Gradient Ternary Nitride Coating Based on Process Control.

Science.gov (United States)

Yan, Pei; Chen, Kaijie; Wang, Yubin; Zhou, Han; Peng, Zeyu; Jiao, Li; Wang, Xibin

2018-05-09

Surface coating is an effective approach to improve cutting tool performance, and multiple or gradient coating structures have become a common development strategy. However, composition mutations at the interfaces decrease the performance of multi-layered coatings. The key mitigation technique has been to reduce the interface effect at the boundaries. This study proposes a structure design method for property-component gradient coatings based on process control. The method produces coatings with high internal cohesion and high external hardness, which could reduce the composition and performance mutations at the interface. A ZrTiN property gradient ternary nitride coating was deposited on cemented carbide by multi-arc ion plating with separated Ti and Zr targets. The mechanical properties, friction behaviors, and cutting performances were systematically investigated, compared with a single-layer coating. The results indicated that the gradient coating had better friction and wear performance with lower wear rate and higher resistance to peeling off during sliding friction. The gradient coating had better wear and damage resistance in cutting processes, with lower machined surface roughness Ra. Gradient-structured coatings could effectively inhibit micro crack initiation and growth under alternating force and temperature load. This method could be extended to similar ternary nitride coatings.

The diffusion bonding of silicon carbide and boron carbide using refractory metals

International Nuclear Information System (INIS)

Cockeram, B.V.

1999-01-01

Joining is an enabling technology for the application of structural ceramics at high temperatures. Metal foil diffusion bonding is a simple process for joining silicon carbide or boron carbide by solid-state, diffusive conversion of the metal foil into carbide and silicide compounds that produce bonding. Metal diffusion bonding trials were performed using thin foils (5 microm to 100 microm) of refractory metals (niobium, titanium, tungsten, and molybdenum) with plates of silicon carbide (both α-SiC and β-SiC) or boron carbide that were lapped flat prior to bonding. The influence of bonding temperature, bonding pressure, and foil thickness on bond quality was determined from metallographic inspection of the bonds. The microstructure and phases in the joint region of the diffusion bonds were evaluated using SEM, microprobe, and AES analysis. The use of molybdenum foil appeared to result in the highest quality bond of the metal foils evaluated for the diffusion bonding of silicon carbide and boron carbide. Bonding pressure appeared to have little influence on bond quality. The use of a thinner metal foil improved the bond quality. The microstructure of the bond region produced with either the α-SiC and β-SiC polytypes were similar

Existence of pareto equilibria for multiobjective games without compactness

OpenAIRE

Shiraishi, Yuya; Kuroiwa, Daishi

2013-01-01

In this paper, we investigate the existence of Pareto and weak Pareto equilibria for multiobjective games without compactness. By employing an existence theorem of Pareto equilibria due to Yu and Yuan([10]), several existence theorems of Pareto and weak Pareto equilibria for the multiobjective games are established in a similar way to Flores-B´azan.

The Zr-Ti-Cr system. Equilibria at 900 and 1100 C degrees

International Nuclear Information System (INIS)

Arico, Sergio F.; Gribaudo, Luis M.

2003-01-01

Main contributions to the knowledge of the ternary system Zr-Ti-Cr were published in the sixties. Stability domains of phases at temperatures between 500 and 1400 C degrees were there presented. Here, results related to the phase diagram at 900 and 1100 C degrees are informed. Three alloys with 40 at.% Cr and different Zr/Ti ratios and one more, richer in Cr, were elaborated. Specimens of the alloys were heat treated 1000 and 800 h at 900 and 1100 C degrees respectively. Phase characterizations were performed by optic metallography and X-ray diffraction analysis. Compositions were determined by microprobe. Alloys with 40 at.% Cr at both temperatures have biphasic equilibria between the intermetallic Laves phase AB 2 and the body-centered cubic solid solution containing principally zirconium and titanium. The Cr-rich alloy presents equilibrium of the AB 2 compound and the Cr-rich solid solution. Results of the present and previous works are used in order to propose new isothermal sections at 900 and 1100 C degrees. (author)

Computing Nash equilibria through computational intelligence methods

Science.gov (United States)

Pavlidis, N. G.; Parsopoulos, K. E.; Vrahatis, M. N.

2005-03-01

Nash equilibrium constitutes a central solution concept in game theory. The task of detecting the Nash equilibria of a finite strategic game remains a challenging problem up-to-date. This paper investigates the effectiveness of three computational intelligence techniques, namely, covariance matrix adaptation evolution strategies, particle swarm optimization, as well as, differential evolution, to compute Nash equilibria of finite strategic games, as global minima of a real-valued, nonnegative function. An issue of particular interest is to detect more than one Nash equilibria of a game. The performance of the considered computational intelligence methods on this problem is investigated using multistart and deflection.

Stochastic Equilibria under Imprecise Deviations in Terminal-Reward Concurrent Games

Directory of Open Access Journals (Sweden)

Patricia Bouyer

2016-09-01

Full Text Available We study the existence of mixed-strategy equilibria in concurrent games played on graphs. While existence is guaranteed with safety objectives for each player, Nash equilibria need not exist when players are given arbitrary terminal-reward objectives, and their existence is undecidable with qualitative reachability objectives (and only three players. However, these results rely on the fact that the players can enforce infinite plays while trying to improve their payoffs. In this paper, we introduce a relaxed notion of equilibria, where deviations are imprecise. We prove that contrary to Nash equilibria, such (stationary equilibria always exist, and we develop a PSPACE algorithm to compute one.

A Computationally Efficient Equation of State for Ternary Gas Hydrate Systems

Science.gov (United States)

White, M. D.

2012-12-01

the production of geologic accumulations of gas hydrates have historically suffered from relatively slow execution times, compared with other multifluid, porous media systems, due to strong nonlinearities and phase transitions. The phase equilibria for the ternary gas hydrate system within the gas hydrate stability range of composition, temperature and pressure, includes regions where the gas hydrate is in equilibrium with gas, nonaqueous liquid, or mixtures of gas and nonaqeuous liquid near the CO2-CH4-N2 mixture critical point. In these regions, solutions to cubic equations of state can be nonconvergent without accurate initial guesses. A hybrid tabular-cubic equation of state is described which avoids convergence issues, but conserves the characteristics and advantages of the cubic equation of state approaches to phase equilibria calculations. The application of interest will be the production of a natural gas hydrate deposit from a geologic formation, using the guest molecule exchange process; where, a mixture of CO2 and N2 are injected into the formation. During the guest-molecule exchange, CO2 and N2 will predominately replace CH4 in the large and small cages of the sI structure, respectively.

True ternary fission in 310126X

International Nuclear Information System (INIS)

Banupriya, B.; Vijayaraghavan, K.R.; Balasubramaniam, M.

2015-01-01

All possible combinations are minimized by the two dimensional minimization process and minimized with respect to neutron numbers and proton numbers of the fragments. Potential energy is low and Q - value is high at true ternary fission region. It shows that true ternary mode is the dominant mode in the ternary fission of superheavy nuclei. Also, the results show that the fragments with neutron magic numbers are the dominant one in the ternary fission of superheavy nuclei whereas the fragments with proton magic numbers are the dominant one in the ternary fission of heavy nuclei

Fabrication of uranium carbide/beryllium carbide/graphite experimental-fuel-element specimens

International Nuclear Information System (INIS)

Muenzer, W.A.

1978-01-01

A method has been developed for fabricating uranium carbide/beryllium carbide/graphite fuel-element specimens for reactor-core-meltdown studies. The method involves milling and blending the raw materials and densifying the resulting blend by conventional graphite-die hot-pressing techniques. It can be used to fabricate specimens with good physical integrity and material dispersion, with densities of greater than 90% of the theoretical density, and with a uranium carbide particle size of less than 10 μm

Strong Nash Equilibria and the Potential Maimizer

NARCIS (Netherlands)

van Megen, F.J.C.; Facchini, G.; Borm, P.E.M.; Tijs, S.H.

1996-01-01

A class of non cooperative games characterized by a `congestion e ect' is studied, in which there exists a strong Nash equilibrium, and the set of Nash equilibria, the set of strong Nash equilibria and the set of strategy pro les maximizing the potential function coincide.The structure of the class

Free-boundary perturbed MHD equilibria

International Nuclear Information System (INIS)

Nührenberg, C

2012-01-01

The concept of perturbed ideal MHD equilibria [Boozer A H and Nuhrenberg C 2006 Phys. Plasmas 13 102501] is employed to study the influence of external error-fields and of small plasma-pressure changes on toroidal plasma equilibria. In tokamak and stellarator free-boundary calculations, benchmarks were successful of the perturbed-equilibrium version of the CAS3D stability code [Nührenberg C et al. 2009 Phys. Rev. Lett. 102 235001] with the ideal MHD equilibrium code NEMEC [Hirshman S P et al. 1986 Comput. Phys. Commun. 43 143].

(Liquid + liquid) equilibria for the ternary mixtures (alkane + toluene + ionic liquid) at T = 298.15 K: Influence of the anion on the phase equilibria

International Nuclear Information System (INIS)

Seoane, Raquel G.; Gómez, Elena; González, Emilio J.; Domínguez, Ángeles

2012-01-01

Highlights: ► [BMpyr][NTF 2 ] and [BMpyr][TFO] were studied as solvents to extract aromatics from alkanes. ► (Liquid + liquid) equilibrium data were measured at 298.15 K for six ternary systems. ► Selectivity and solute distribution ratio were calculated and compared. ► The influence of the structure of anion of the ionic liquid was analyzed. ► Experimental data were satisfactorily correlated using NRTL model. - Abstract: (Liquid + liquid) equilibrium data for the ionic liquids 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide, [BMpyr][NTf 2 ], and 1-butyl-1-methylpyrrolidinium trifluoromethanesulfonate, [BMpyr][TFO], with toluene, and heptane or cyclohexane were determined at T = 298.15 K and atmospheric pressure. In order to check if these ILs can be used as potential solvents for the extraction of toluene from aliphatic compounds, the ability of the ILs as solvents was evaluated in terms of selectivity and solute distribution ratio. The experimental data were correlated accurately with the Non Random Two-Liquid model.

LIQUID-LIQUID EQUILIBRIA OF THE TERNARY SYSTEMS PROPIONIC ACID - WATER - SOLVENT (n-AMYL ALCOHOL AND n-AMYL ACETATE

Directory of Open Access Journals (Sweden)

Dilek ÖZMEN

2005-02-01

Full Text Available The experimental liquid-liquid equilibrium (LLE data have been obtained at 25 oC for ternary systems propionic acid-water-n-amyl alcohol and propionic acid-water-n-amyl acetate. The reliability of the experimental tie line data are checked using the methods of Othmer-Tobias and Hand. The distribution coefficients and separation factors were obtained from experimental results and are also reported. The predicted tie line data obtained by UNIFAC method are compared with experimental data. It is concluded that n-amyl alcohol and n-amyl acetate are suitable separating agents for dilute aqueous propionic acid solutions.

Surface current equilibria from a geometric point of view

International Nuclear Information System (INIS)

Kaiser, R.; Salat, A.

1993-04-01

This paper addresses the inverse problem of the existence of surface current MHD equilibria in toroidal geometry with vanishing magnetic field inside. Inverse means that the plasma-vacuum interface rather than the external wall or conductors are given and the latter remain to be determined. This makes a reformulation of the problem possible in geometric terms: What toroidal surfaces with analytic parameterization allow a simple analytic covering by geodesics? If such a covering by geodesics (field lines) exists, their orthogonal trajectories (current lines) also form a simple covering and are described by a function satisfying a nonlinear partial differential equation of the Hamilton-Jacobi type whose coefficients are combinations of the metric elements of the surface. All known equilibria - equilibria with zero and infinite rotational transform and the symmetric ones in the case of finite rotational transform - turn out to be solutions of separable cases of that equation and allow a unified description if the toroidal surface is parametrized in the moving trihedral associated with a closed curve. Analogously to volume current equilibria, the only continuous symmetries compatible with separability are plane, helical and axial symmetry. In the nonseparable case numerical evidence is presented for cases with chaotic behaviour of geodesics, thus restricting possible equilibria for these surfaces. For weak deviation from axisymmetry KAM-type behaviour is observed, i.e. destruction of geodesic coverings with a low rational rotational transform and preservation of those with irrational rotational transform. A previous attempt to establish three-dimensional surface current equilibria on the basis of the KAM theorem is rejected as incomplete, and a complete proof of the existence of equilibria in the weakly nonaxisymmetric case, based on the twist theorem for mappings, is given. Finally, for a certain class of strong deviations from axisymmetry an analytic criterion is

Nash Equilibria in Fisher Market

Science.gov (United States)

Adsul, Bharat; Babu, Ch. Sobhan; Garg, Jugal; Mehta, Ruta; Sohoni, Milind

Much work has been done on the computation of market equilibria. However due to strategic play by buyers, it is not clear whether these are actually observed in the market. Motivated by the observation that a buyer may derive a better payoff by feigning a different utility function and thereby manipulating the Fisher market equilibrium, we formulate the Fisher market game in which buyers strategize by posing different utility functions. We show that existence of a conflict-free allocation is a necessary condition for the Nash equilibria (NE) and also sufficient for the symmetric NE in this game. There are many NE with very different payoffs, and the Fisher equilibrium payoff is captured at a symmetric NE. We provide a complete polyhedral characterization of all the NE for the two-buyer market game. Surprisingly, all the NE of this game turn out to be symmetric and the corresponding payoffs constitute a piecewise linear concave curve. We also study the correlated equilibria of this game and show that third-party mediation does not help to achieve a better payoff than NE payoffs.

Isotope effects in ion-exchange equilibria in aqueous and mixed solvent systems

International Nuclear Information System (INIS)

Gupta, A.R.

1979-01-01

Isotope effects in ion-exchange equilibria in aqueous and mixed solvents are analyzed in terms of the general features of ion-exchange equilibria and of isotope effects in chemical equilibria. The special role of solvent fractionation effects in ion-exchange equilibria in mixed solvents is pointed out. The various situations arising in isotope fractionation in ion exchange in mixed solvents due to solvent fractionation effects are theoretically discussed. The experimental data on lithium isotope effects in ion-exchange equilibria in mixed solvents are shown to conform to the above situations. The limitations of ion-exchange equilibria in mixed solvents for isotope fractionation are pointed out. 3 tables

On Nash-Equilibria of Approximation-Stable Games

Science.gov (United States)

Awasthi, Pranjal; Balcan, Maria-Florina; Blum, Avrim; Sheffet, Or; Vempala, Santosh

One reason for wanting to compute an (approximate) Nash equilibrium of a game is to predict how players will play. However, if the game has multiple equilibria that are far apart, or ɛ-equilibria that are far in variation distance from the true Nash equilibrium strategies, then this prediction may not be possible even in principle. Motivated by this consideration, in this paper we define the notion of games that are approximation stable, meaning that all ɛ-approximate equilibria are contained inside a small ball of radius Δ around a true equilibrium, and investigate a number of their properties. Many natural small games such as matching pennies and rock-paper-scissors are indeed approximation stable. We show furthermore there exist 2-player n-by-n approximation-stable games in which the Nash equilibrium and all approximate equilibria have support Ω(log n). On the other hand, we show all (ɛ,Δ) approximation-stable games must have an ɛ-equilibrium of support O(Δ^{2-o(1)}/ɛ2{log n}), yielding an immediate n^{O(Δ^{2-o(1)}/ɛ^2log n)}-time algorithm, improving over the bound of [11] for games satisfying this condition. We in addition give a polynomial-time algorithm for the case that Δ and ɛ are sufficiently close together. We also consider an inverse property, namely that all non-approximate equilibria are far from some true equilibrium, and give an efficient algorithm for games satisfying that condition.

Porous silicon carbide (SIC) semiconductor device

Science.gov (United States)

Shor, Joseph S. (Inventor); Kurtz, Anthony D. (Inventor)

1996-01-01

Porous silicon carbide is fabricated according to techniques which result in a significant portion of nanocrystallites within the material in a sub 10 nanometer regime. There is described techniques for passivating porous silicon carbide which result in the fabrication of optoelectronic devices which exhibit brighter blue luminescence and exhibit improved qualities. Based on certain of the techniques described porous silicon carbide is used as a sacrificial layer for the patterning of silicon carbide. Porous silicon carbide is then removed from the bulk substrate by oxidation and other methods. The techniques described employ a two-step process which is used to pattern bulk silicon carbide where selected areas of the wafer are then made porous and then the porous layer is subsequently removed. The process to form porous silicon carbide exhibits dopant selectivity and a two-step etching procedure is implemented for silicon carbide multilayers.

Description of the ternary system Cu-Ge-Te

International Nuclear Information System (INIS)

Dogguy, M.; Carcaly, C.; Rivet, J.; Flahaut, J.

1977-01-01

The Cu-Ge-Te ternary system has been studied by DTA and by crystallographic and metallographic analysis. The existence of a ternary compound Cu 2 GeTe 3 is demonstrated; this compound has a ternary incongruent melting point at 500 0 C. This ternary compound has a superstructure of a zinc blende type. The study shows the existence of five ternary eutectics. Two liquid-liquid miscibility gaps exist: the first is situated entirely in the ternary system; the second gives a monotectic region within the ternary system. (Auth.)

Plasma spraying of zirconium carbide – hafnium carbide – tungsten cermets

Czech Academy of Sciences Publication Activity Database

Brožek, Vlastimil; Ctibor, Pavel; Cheong, D.-I.; Yang, S.-H.

2009-01-01

Roč. 9, č. 1 (2009), s. 49-64 ISSN 1335-8987 Institutional research plan: CEZ:AV0Z20430508 Keywords : Plasma spraying * cermet coatings * microhardness * zirconium carbide * hafnium carbide * tungsten * water stabilized plasma Subject RIV: JH - Ceramics, Fire-Resistant Materials and Glass

Metal Carbides for Biomass Valorization

Directory of Open Access Journals (Sweden)

Carine E. Chan-Thaw

2018-02-01

Full Text Available Transition metal carbides have been utilized as an alternative catalyst to expensive noble metals for the conversion of biomass. Tungsten and molybdenum carbides have been shown to be effective catalysts for hydrogenation, hydrodeoxygenation and isomerization reactions. The satisfactory activities of these metal carbides and their low costs, compared with noble metals, make them appealing alternatives and worthy of further investigation. In this review, we succinctly describe common synthesis techniques, including temperature-programmed reaction and carbothermal hydrogen reduction, utilized to prepare metal carbides used for biomass transformation. Attention will be focused, successively, on the application of transition metal carbide catalysts in the transformation of first-generation (oils and second-generation (lignocellulose biomass to biofuels and fine chemicals.

Ternary-fragmentation-driving potential energies of 252Cf

Science.gov (United States)

Karthikraj, C.; Ren, Zhongzhou

2017-12-01

Within the framework of a simple macroscopic model, the ternary-fragmentation-driving potential energies of 252Cf are studied. In this work, all possible ternary-fragment combinations of 252Cf are generated by the use of atomic mass evaluation-2016 (AME2016) data and these combinations are minimized by using a two-dimensional minimization approach. This minimization process can be done in two ways: (i) with respect to proton numbers (Z1, Z2, Z3) and (ii) with respect to neutron numbers (N1, N2, N3) of the ternary fragments. In this paper, the driving potential energies for the ternary breakup of 252Cf are presented for both the spherical and deformed as well as the proton-minimized and neutron-minimized ternary fragments. From the proton-minimized spherical ternary fragments, we have obtained different possible ternary configurations with a minimum driving potential, in particular, the experimental expectation of Sn + Ni + Ca ternary fragmentation. However, the neutron-minimized ternary fragments exhibit a driving potential minimum in the true-ternary-fission (TTF) region as well. Further, the Q -value energy systematics of the neutron-minimized ternary fragments show larger values for the TTF fragments. From this, we have concluded that the TTF region fragments with the least driving potential and high Q values have a strong possibility in the ternary fragmentation of 252Cf. Further, the role of ground-state deformations (β2, β3, β4, and β6) in the ternary breakup of 252Cf is also studied. The deformed ternary fragmentation, which involves Z3=12 -19 fragments, possesses the driving potential minimum due to the larger oblate deformations. We also found that the ground-state deformations, particularly β2, strongly influence the driving potential energies and play a major role in determining the most probable fragment combinations in the ternary breakup of 252Cf.

Isobaric (vapor + liquid) equilibria for the ternary system of (ethanol + water + 1,3-propanediol) and three constituent binary systems at P = 101.3 kPa

International Nuclear Information System (INIS)

Lai, Hung-Sheng; Lin, Yi-Feng; Tu, Chein-Hsiun

2014-01-01

Highlights: • We report VLE data at 101.3 kPa for mixtures of ethanol, water, and 1,3-propanediol. • The VLE data were correlated by the Wilson, NRTL, and UNIQUAC models. • The ternary VLE data were predicted from binary VLE data using the three models. • The VLE effect of 1,3-propanediol on the azeotropic ethanol + water mixture was studied. • The azeotropic point of ethanol + water disappears at 30 wt% of 1,3-propanediol. -- Abstract: Isobaric (vapor + liquid) equilibrium (VLE) at P = 101.3 kPa have been measured for the ternary system of (ethanol + water + 1,3-propanediol) and for the corresponding binary systems of (ethanol + water), (ethanol + 1,3-propanediol), and (water + 1,3-propnaediol) using a Hunsmann-type equilibrium still with circulation of both vapor and liquid phases. The ternary mixtures were prepared by mixing ethanol and pure water with three concentrations (10, 30, and 50) wt% of 1,3-propanediol in the overall liquid mixtures in order to study the effect of 1,3-propanediol on the VLE of (ethanol + water). The equilibrium compositions of mixtures were analyzed by gas–liquid chromatography. The relative volatilities of ethanol with respect to water were also determined. The results of the investigation indicate the disappearance of the binary azeotrope between ethanol and water when the concentration of 1,3-propanediol is up to 30 wt%. The liquid activity coefficients were calculated using the modified Raoult’s law. The thermodynamic consistency of the VLE data was performed for the three binary systems using Van Ness direct test. The new binary and ternary VLE data were successfully correlated using the Wilson, NRTL, and UNIQUAC models, for which the binary interaction parameters are reported

High-Efficient Circuits for Ternary Addition

Directory of Open Access Journals (Sweden)

Reza Faghih Mirzaee

2014-01-01

Full Text Available New ternary adders, which are fundamental components of ternary addition, are presented in this paper. They are on the basis of a logic style which mostly generates binary signals. Therefore, static power dissipation reaches its minimum extent. Extensive different analyses are carried out to examine how efficient the new designs are. For instance, the ternary ripple adder constructed by the proposed ternary half and full adders consumes 2.33 μW less power than the one implemented by the previous adder cells. It is almost twice faster as well. Due to their unique superior characteristics for ternary circuitry, carbon nanotube field-effect transistors are used to form the novel circuits, which are entirely suitable for practical applications.

On Equilibria of the Two-fluid Model in Magnetohydrodynamics

International Nuclear Information System (INIS)

Frantzeskakis, Dimitri J.; Stratis, Ioannis G.; Yannacopoulos, Athanasios N.

2004-01-01

We show how the equilibria of the two-fluid model in magnetohydrodynamics can be described by the double curl equation and through the study of this equation we study some properties of these equilibria

A unifying approach to existence of Nash equilibria

NARCIS (Netherlands)

Balder, E.J.

1997-01-01

An approach initiated in [4] is shown to unify results about the existence of (i) Nash equilibria in games with at most countably many players, (ii) Cournot-Nash equilibrium distributions for large, anonymous games, and (iii) Nash equilibria (both mixed and pure) for continuum games. A new, central

Two-fluid equilibria with flow

International Nuclear Information System (INIS)

Steinhauer, L.

1999-01-01

The formalism is developed for flowing two-fluid equilibria. The equilibrium system is governed by a pair of second order partial differential equations for the magnetic stream function and the ion stream function plus a Bernoulli-like equation for the density. There are six arbitrary surface function. There are separate characteristic surfaces for each species, which are the guiding-center surfaces. This system is a generalization of the familiar Grad-Shafranov system for a single-fluid equilibrium without flow, which has only one equation and two arbitrary surface functions. In the case of minimum energy equilibria, the six surface functions take on particular forms. (author)

The Pierce diode with an external circuit: II, Non-uniform equilibria

International Nuclear Information System (INIS)

Lawson, W.S.

1987-01-01

The non-uniform (non-linear) equilibria of the classical (short circuit) Pierce diode and the extended (series RLC external circuit) Pierce diode are described theoretically, and explored via computer simulation. It is found that most equilibria are correctly predicted by theory, but that the continuous set of equilibria of the classical Pierce diode at α = 2π are not observed. The stability characteristics of the non-uniform equilibria are also worked out, and are consistent with the simulations. 8 refs., 22 figs., 3 tabs

Vapor-Liquid Equilibria in the Binary and Ternary Systems Composed of 2-Methylpentane, 3-Methyl-2-Butanone and 3-Methyl-2-Butanol

Czech Academy of Sciences Publication Activity Database

Psutka, Štěpán; Wichterle, Ivan

2005-01-01

Roč. 50, č. 4 (2005), s. 1338-1342 ISSN 0021-9568 R&D Projects: GA ČR(CZ) GA104/03/1555; GA AV ČR(CZ) KSK4040110 Institutional research plan: CEZ:AV0Z40720504 Keywords : vapor-liquid equilibrium * binary- ternary systems * isothermal Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 1.610, year: 2005

Evaluation of a Mathematical Model for Single Component Adsorption Equilibria with Reference to the Prediction of Multicomponent Adsorption Equilibria

DEFF Research Database (Denmark)

Krøll, Annette Elisabeth; Marcussen, Lis

1997-01-01

An equilibrium equation for pure component adsorption is compared to experiments and to the vacancy solution theory. The investigated equilibrium equation is a special case of a model for prediction of multicomponent adsorption equilibria.The vacancy solution theory for multicomponent systems...... requires binary experimental data for determining the interaction parameters of the Wilson equation; thus a large number of experiments are needed. The multicomponent equilibria model which is investigated for single component systems in this work is based on pure component data only. This means...... that the requirement for experimental data is reduced significantly.The two adsorption models are compared, using experimental pure gas adsorption data found in literature. The results obtained by the models are in close agreement for pure component equilibria and they give a good description of the experimental data...

Ternary q-Virasoro-Witt Hom-Nambu-Lie algebras

International Nuclear Information System (INIS)

Ammar, F; Makhlouf, A; Silvestrov, S

2010-01-01

In this paper we construct ternary q-Virasoro-Witt algebras which q-deform the ternary Virasoro-Witt algebras constructed by Curtright, Fairlie and Zachos using su(1, 1) enveloping algebra techniques. The ternary Virasoro-Witt algebras constructed by Curtright, Fairlie and Zachos depend on a parameter and are not Nambu-Lie algebras for all but finitely many values of this parameter. For the parameter values for which the ternary Virasoro-Witt algebras are Nambu-Lie, the corresponding ternary q-Virasoro-Witt algebras constructed in this paper are also Hom-Nambu-Lie because they are obtained from the ternary Nambu-Lie algebras using the composition method. For other parameter values this composition method does not yield a Hom-Nambu-Lie algebra structure for q-Virasoro-Witt algebras. We show however, using a different construction, that the ternary Virasoro-Witt algebras of Curtright, Fairlie and Zachos, as well as the general ternary q-Virasoro-Witt algebras we construct, carry a structure of the ternary Hom-Nambu-Lie algebra for all values of the involved parameters.

Peculiarities of thermoelectric half-Heusler phase formation in Zr–Co–Sb ternary system

Energy Technology Data Exchange (ETDEWEB)

Romaka, V.V., E-mail: romakav@lp.edu.ua [Department of Applied Material Science and Materials Engineering, Lviv Polytechnic National University, Ustyyanovycha Str. 5, 79013 Lviv (Ukraine); Institut für Physikalische Chemie, Universität Wien, Währingerstr. 42, A-1090 Wien (Austria); Romaka, L. [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya Str. 6, 79005 Lviv (Ukraine); Rogl, P. [Institut für Physikalische Chemie, Universität Wien, Währingerstr. 42, A-1090 Wien (Austria); Stadnyk, Yu. [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya Str. 6, 79005 Lviv (Ukraine); Melnychenko, N. [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya Str. 6, 79005 Lviv (Ukraine); Army Academy named after Hetman Petro Sahaydachnyi, Gvardijska Str. 32, 79012 Lviv (Ukraine); Korzh, R.; Duriagina, Z. [Department of Applied Material Science and Materials Engineering, Lviv Polytechnic National University, Ustyyanovycha Str. 5, 79013 Lviv (Ukraine); Horyn, A. [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya Str. 6, 79005 Lviv (Ukraine)

2014-02-05

Highlights: • Phase relations for the Zr–Co–Sb system at 500 °C. • Homogeneity region for half-Heusler phase. • The distribution of DOS for Zr{sub 1+x}Co{sub 1−x}Sb predicts transition from semiconductor (x = 0) to metallic (x = 0.13) like behavior. • The existence of the solid solution Zr{sub 5}Co{sub x}Sb{sub 3+y} (x = 0.0–1.0, y = 0.0–1.0). -- Abstract: The phase equilibria in the Zr–Co–Sb ternary system were studied at 873 K by means of X-ray and metallographic analyses in the whole concentration range. The interaction between the elements results the formation of four ternary compounds at investigated temperature: ZrCoSb (MgAgAs-type), Zr{sub 6}CoSb{sub 2} (K{sub 2}UF{sub 6}-type), Zr{sub 5}CoSb{sub 3} (Hf{sub 5}CuSn{sub 3}-type) and Zr{sub 5}Co{sub 0.5}Sb{sub 2.5} (W{sub 5}Si{sub 3}-type). The limited composition Zr{sub 5}CoSb{sub 3} of the solid solution based on the Zr{sub 5}Sb{sub 3−4} binaries is considered as compound with Hf{sub 5}CuSn{sub 3} structure type. The influence of the disordering and defects in the crystal structure of ZrCoSb on the physical properties was analyzed. The performed electronic structure calculations are in good agreement with electrical and magnetic studies.

Ternary scandium and transition metals germanides

International Nuclear Information System (INIS)

Kotur, B.Ya.

1992-01-01

Brief review of data on phase diagram of ternary Sc-Me-Ge systems (Me-d - , f-transition element) is given. Isothermal sections at 870 and 1070 K of 17 ternary systems are plotted. Compositions and their structural characteristics are presented. Variability of crystal structure is typical for ternary scandium germanides: 70 compounds with the studied structure belong to 23 structural types. Ternary germanides isostructural to types of Sm 4 Ge 4 , ZrCrSi 2 , ZrNiAl, ScCeSi, TiNiSi U 4 Re 7 Si 6 145 compounds from 70 under investigation are mostly formed in studied systems

Shallow-water vortex equilibria and their stability

Energy Technology Data Exchange (ETDEWEB)

Plotka, H; Dritschel, D G, E-mail: hanna@mcs.st-andrews.ac.uk, E-mail: dgd@mcs.st-andrews.ac.uk [School of Mathematics and Statistics, University of St Andrews, North Haugh, St. Andrews KY16 9SS (United Kingdom)

2011-12-22

We first describe the equilibrium form and stability of steadily-rotating simply-connected vortex patches in the single-layer quasi-geostrophic model of geophysical fluid dynamics. This model, valid for rotating shallow-water flow in the limit of small Rossby and Froude numbers, has an intrinsic length scale L{sub D} called the 'Rossby deformation length' relating the strength of stratification to that of the background rotation rate. Specifically, L{sub D} = c/f where c={radical}gH is a characteristic gravity-wave speed, g is gravity (or 'reduced' gravity in a two-layer context where one layer is infinitely deep), H is the mean active layer depth, and f is the Coriolis frequency (here constant). We next introduce ageostrophic effects by using the full shallow-water model to generate what we call 'quasi-equilibria'. These equilibria are not strictly steady, but radiate such weak gravity waves that they are steady for all practical purposes. Through an artificial ramping procedure, we ramp up the potential vorticity anomaly of the fluid particles in our quasi-geostrophic equilibria to obtain shallow-water quasi-equilibria at finite Rossby number. We show a few examples of these states in this paper.

Microstructural Study of Titanium Carbide Coating on Cemented Carbide

DEFF Research Database (Denmark)

Vuorinen, S.; Horsewell, Andy

1982-01-01

Titanium carbide coating layers on cemented carbide substrates have been investigated by transmission electron microscopy. Microstructural variations within the typically 5µm thick chemical vapour deposited TiC coatings were found to vary with deposit thickness such that a layer structure could...... be delineated. Close to the interface further microstructural inhomogeneities were obsered, there being a clear dependence of TiC deposition mechanism on the chemical and crystallographic nature of the upper layers of the multiphase substrate....

Uniqueness of Nash equilibria in a quantum Cournot duopoly game

International Nuclear Information System (INIS)

Sekiguchi, Yohei; Sakahara, Kiri; Sato, Takashi

2010-01-01

A quantum Cournot game whose classical form game has multiple Nash equilibria is examined. Although the classical equilibria fail to be Pareto optimal, the quantum equilibrium exhibits the following two properties: (i) if the measurement of entanglement between strategic variables chosen by the competing firms is sufficiently large, the multiplicity of equilibria vanishes, and (ii) the more strongly the strategic variables are entangled, the more closely the unique equilibrium approaches to the optimal one.

Azeotropic behaviour of (benzene + cyclohexane + chlorobenzene) ternary mixture using chlorobenzene as entrainer at 101.3 kPa

International Nuclear Information System (INIS)

Silva, L.M.C.; Mattedi, S.; Gonzalez-Olmos, R.; Iglesias, M.

2006-01-01

In this paper, the azeotropic behaviour of the (benzene + cyclohexane + chlorobenzene) ternary mixture was experimentally investigated with the aim of enhancing the knowledge for the feasible use of chlorobenzene as an entrainer for the azeotropic distillation of the binary azeotrope. Such a study has not been reported in the literature to the best of the authors' knowledge. (Vapour + liquid) equilibria data for (benzene + cyclohexane + chlorobenzene) at 101.3 kPa were obtained with a Othmer-type ebulliometer. Data were tested and considered thermodynamically consistent. The experimental results showed that this ternary mixture is completely miscible and exhibits an unique binary homogeneous azeotrope, an unstable node at the conditions studied, and the propitious topological characteristics (residual curve map and relative volatility) to be separated. Satisfactory results were obtained for the correlation of equilibrium compositions with the UNIQUAC activity coefficients model and also for prediction with the UNIFAC method. In both cases, low root mean square deviations of the vapour mole fraction and temperature were calculated. The capability of chlorobenzene as a modified distillation agent at atmospheric condition is discussed in terms of the thermodynamic topological analysis. A conceptual distillation scheme with reversed volatility is proposed to separate the azeotropic mixture. In order to reduce the operational cost requirements of the sequence of columns proposed, the range for optimal reflux and the ratio for feed flow conditions were studied

Azeotropic behaviour of (benzene + cyclohexane + chlorobenzene) ternary mixture using chlorobenzene as entrainer at 101.3 kPa

Energy Technology Data Exchange (ETDEWEB)

Silva, L.M.C. [Departamento de Engenharia Quimica, Escola Politecnica, Universidade Federal da Bahia, 40210 Salvador de Bahia (Brazil); Mattedi, S. [Departamento de Engenharia Quimica, Escola Politecnica, Universidade Federal da Bahia, 40210 Salvador de Bahia (Brazil); Gonzalez-Olmos, R. [Departament d' Enginyeria Quimica, Escola Tecnica Superior d' Enginyeria Quimica, Universitat Rovira i Virgili, Avinguda Paisos Catalans 26, Campus Sescelades, 43007 Tarragona (Spain); Iglesias, M. [Departament d' Enginyeria Quimica, Escola Tecnica Superior d' Enginyeria Quimica, Universitat Rovira i Virgili, Avinguda Paisos Catalans 26, Campus Sescelades, 43007 Tarragona (Spain)]. E-mail: miguelangel.iglesias@urv.net

2006-12-15

In this paper, the azeotropic behaviour of the (benzene + cyclohexane + chlorobenzene) ternary mixture was experimentally investigated with the aim of enhancing the knowledge for the feasible use of chlorobenzene as an entrainer for the azeotropic distillation of the binary azeotrope. Such a study has not been reported in the literature to the best of the authors' knowledge. (Vapour + liquid) equilibria data for (benzene + cyclohexane + chlorobenzene) at 101.3 kPa were obtained with a Othmer-type ebulliometer. Data were tested and considered thermodynamically consistent. The experimental results showed that this ternary mixture is completely miscible and exhibits an unique binary homogeneous azeotrope, an unstable node at the conditions studied, and the propitious topological characteristics (residual curve map and relative volatility) to be separated. Satisfactory results were obtained for the correlation of equilibrium compositions with the UNIQUAC activity coefficients model and also for prediction with the UNIFAC method. In both cases, low root mean square deviations of the vapour mole fraction and temperature were calculated. The capability of chlorobenzene as a modified distillation agent at atmospheric condition is discussed in terms of the thermodynamic topological analysis. A conceptual distillation scheme with reversed volatility is proposed to separate the azeotropic mixture. In order to reduce the operational cost requirements of the sequence of columns proposed, the range for optimal reflux and the ratio for feed flow conditions were studied.

Two-dimensional magnetohydrodynamic equilibria with flow and studies of equilibria fluctuations

International Nuclear Information System (INIS)

Agim, Y.Z.

1989-08-01

A set of reduced ideal MHD equations is derived to investigate equilibria of plasmas with mass flow in general two-dimensional geometry. These equations provide a means of investigating the effects of flow on self-consistent equilibria in a number of new two-dimensional configurations such as helically symmetric configurations with helical axis, which are relevant to stellarators, as well as axisymmetric configurations. It is found that as in the axisymmetric case, general two-dimensional flow equilibria are governed by a second-order quasi-linear partial differential equation for a magnetic flux function, which is coupled to a Bernoulli-type equation for the density. The equation for the magnetic flux function becomes hyperbolic at certain critical flow speeds which follow from its characteristic equation. When the equation is hyperbolic, shock phenomena may exist. As a particular example, unidirectional flow along the lines of symmetry is considered. In this case, the equation mentioned above is always elliptic. An exact solution for the case of helically symmetric unidirectional flow is found and studied to determine flow effects on the magnetic topology. In second part of this thesis, magnetic fluctuations due to the thermally excited MHD waves are investigated using fluid and kinetic models to describe stable, uniform, compressible plasma in the range above the drift wave frequency and below the ion cyclotron frequency. It is shown that the fluid model with resistivity yields spectral densities which are roughly Lorentzian, exhibit equipartition with no apparent cutoff in wavenumber space and a Bohm-type diffusion coefficient. Under certain conditions, the ensuing transport may be comparable to classical values. For a phenomenological cutoff imposed on the spectrum, the typical fluctuating-to-equilibrium magnetic field ratio is found to be of the order of 10 -10

On tokamak equilibria with a zero current or negative current central region

International Nuclear Information System (INIS)

Chu, M.S.; Parks, P.B.

2002-01-01

Several tokamak experiments have reported the development of a central region with vanishing currents (the current hole). The straightforward application of results from the work of Greene, Johnson and Weimer [Phys. Fluids 14, 671 (1971)] on a tokamak equilibrium to these plasmas leads to the apparent singularities in several physical quantities including the Shafranov shift and casts doubts on the existence of this type of equilibria. In this paper, the above quoted equilibrium theory is re-examined and extended to include equilibria with a current hole. It is shown that singularities can be circumvented and that equilibria with a central current hole do satisfy the magnetohydrodynamic equilibrium condition with regular behavior for all the physical quantities and do not lead to infinitely large Shafranov shifts. Isolated equilibria with negative current in the central region could exist. But equilibria with negative currents in general do not have neighboring equilibria and thus cannot have experimental realization, i.e., no negative currents can be driven in the central region

The Pierce diode with an external circuit. I. Oscillations about nonuniform equilibria

International Nuclear Information System (INIS)

Lawson, W.S.

1989-01-01

The nonuniform (nonlinear) equilibria of the classical (short circuit) Pierce diode and the extended (series RLC external circuit) Pierce diode are described, and the spectrum of oscillations (stable and unstable) about these equilibria are worked out. It is found that only the external capacitance alters the equilibria, though all elements alter the spectrum. In particular, the introduction of an external capacitor destabilizes some equilibria that are marginally stable without the capacitor. Computer simulations are performed to test the theoretical predictions for the case of an external capacitor only. It is found that most equilibria are correctly predicted by theory, but that the continuous set of equilibria of the classical Pierce diode at Pierce parameters (α=ω/sub pL//v 0 ) that are multiples of 2π are not observed. This appears to be a failure of the simulation method under the rather singular conditions rather than a failure of the theory

Nematic Equilibria on a Two-Dimensional Annulus

KAUST Repository

Lewis, A. H.; Aarts, D. G. A. L.; Howell, P. D.; Majumdar, A.

2017-01-01

We study planar nematic equilibria on a two-dimensional annulus with strong and weak tangent anchoring, in the Oseen–Frank theoretical framework. We analyze a radially invariant defect-free state and compute analytic stability criteria for this state in terms of the elastic anisotropy, annular aspect ratio, and anchoring strength. In the strong anchoring case, we define and characterize a new spiral-like equilibrium which emerges as the defect-free state loses stability. In the weak anchoring case, we compute stability diagrams that quantify the response of the defect-free state to radial and azimuthal perturbations. We study sector equilibria on sectors of an annulus, including the effects of weak anchoring and elastic anisotropy, giving novel insights into the correlation between preferred numbers of boundary defects and the geometry. We numerically demonstrate that these sector configurations can approximate experimentally observed equilibria with boundary defects.

Nematic Equilibria on a Two-Dimensional Annulus

KAUST Repository

Lewis, A. H.

2017-01-16

We study planar nematic equilibria on a two-dimensional annulus with strong and weak tangent anchoring, in the Oseen–Frank theoretical framework. We analyze a radially invariant defect-free state and compute analytic stability criteria for this state in terms of the elastic anisotropy, annular aspect ratio, and anchoring strength. In the strong anchoring case, we define and characterize a new spiral-like equilibrium which emerges as the defect-free state loses stability. In the weak anchoring case, we compute stability diagrams that quantify the response of the defect-free state to radial and azimuthal perturbations. We study sector equilibria on sectors of an annulus, including the effects of weak anchoring and elastic anisotropy, giving novel insights into the correlation between preferred numbers of boundary defects and the geometry. We numerically demonstrate that these sector configurations can approximate experimentally observed equilibria with boundary defects.

Numerical calculation of axisymmetric non-neutral plasma equilibria

International Nuclear Information System (INIS)

Spencer, R.L.; Rasband, S.N.; Vanfleet, R.R.

1993-01-01

Efficient techniques for computing axisymmetric non-neutral plasma equilibria are described. These equilibria may be obtained either by requiring global thermal equilibrium, by specifying the midplane radial density profile, or by specifying the radial profile of ∫n dz. Both splines and finite-differences are used, and the accuracy of the two is compared by using a new characterization of the thermal equilibrium density profile which gives a simple formula for estimating the radial and axial gradient scale lengths of thermal equilibria. It is found that for global thermal equilibrium 1% accuracy is achieved with splines if the distance between neighboring splines is about two Debye lengths while finite differences require a grid spacing of about one-half Debye length to achieve the same accuracy

Ternary and binary LLE measurements for solvent (2-methyltetrahydrofuran and cyclopentyl methyl ether) + furfural + water between 298 and 343 K

International Nuclear Information System (INIS)

Männistö, Mikael; Pokki, Juha-Pekka; Fournis, Ludivine; Alopaeus, Ville

2017-01-01

Highlights: • Novel LLE of 2-methyltetrahydrofuran or cyclopentyl methyl ether + furfural + water. • High performance solvents for liquid-liquid extraction exhibited. • Modelled with UNIQUAC-HOC activity coefficient model. • Comparison to other industrial solvents with distribution coefficient and selectivity. - Abstract: The suitability of two solvents for the extraction of furfural from aqueous streams is assessed through novel ternary and binary liquid-liquid equilibria data for mixtures of solvent (2-methyltetrahydrofuran or cyclopentyl methyl ether) + furfural + water. The measured data are reported along with regressed binary interaction parameters for UNIQUAC-HOC activity coefficient model and further analyzed through distribution coefficients and selectivity for furfural. Out of the two solvents, cyclopentyl methyl ether presents a very high selectivity along with good distribution coefficient in the entire temperature range.

Kinetic and thermodynamic study of lithium ternary amalgams in contact with solvated lithium hydroxide

International Nuclear Information System (INIS)

Cordova M, M.

1991-12-01

Lithium amalgams are used on lithium isotope separation, the process has been studied in its different parameters, but there is no information on the isotopic separation in the presence of ternary metals diluted in the amalgam. The latest voltammetric technique developed for trace analysis is used for the study, to determine the effects of the presence of cadmium, which has been selected on compatibility criteria with the system, in the intermetallic structures of the amalgam. The differential pulse anodic stripping voltammetry indicates the presence of an intermetallic persistent structure after the potassium and lithium oxidation. This structure has a slow formation and destruction rate, with an anionic character, which accounts for the oxidation potential displacement of the amalgamated metals. The activation energy results of amalgam decomposition reaction in contact with water, allows to establish the intermetallic effects on this reaction, raising the energy of the activated state, on condition that there were time to form it. A reaction mechanism is proposed that agrees with these results. The study of the isotopic composition indicates that the intermetallic species affect the thermodynamic equilibrium between the phases in contact. The measurements of the system's isotopic composition do not give exact values for the separation factors, but they establish a difference in the sign of enthalpies of the isotopic equilibria. The enthalpy for the isotopic exchange for the binary amalgam is negative, with a value that agrees with those in the literature. Nevertheless, those of the ternary systems are positive, indicating an endothermic character process. (author)

Helium diffusion in irradiated boron carbide

International Nuclear Information System (INIS)

Hollenberg, G.W.

1981-03-01

Boron carbide has been internationally adopted as the neutron absorber material in the control and safety rods of large fast breeder reactors. Its relatively large neutron capture cross section at high neutron energies provides sufficient reactivity worth with a minimum of core space. In addition, the commercial availability of boron carbide makes it attractive from a fabrication standpoint. Instrumented irradiation experiments in EBR-II have provided continuous helium release data on boron carbide at a variety of operating temperatures. Although some microstructural and compositional variations were examined in these experiments most of the boron carbide was prototypic of that used in the Fast Flux Test Facility. The density of the boron carbide pellets was approximately 92% of theoretical. The boron carbide pellets were approximately 1.0 cm in diameter and possessed average grain sizes that varied from 8 to 30 μm. Pellet centerline temperatures were continually measured during the irradiation experiments

Kinetics of niobium carbide precipitation in ferrite

International Nuclear Information System (INIS)

Gendt, D.

2001-01-01

The aim of this study is to develop a NbC precipitation modelling in ferrite. This theoretical study is motivated by the fact it considers a ternary system and focus on the concurrence of two different diffusion mechanisms. An experimental study with TEP, SANS and Vickers micro-hardening measurements allows a description of the NbC precipitation kinetics. The mean radius of the precipitates is characterized by TEM observations. To focus on the nucleation stage, we use the Tomographic Atom Probe that analyses, at an atomistic scale, the position of the solute atoms in the matrix. A first model based on the classical nucleation theory and the diffusion-limited growth describes the precipitation of spherical precipitates. To solve the set of equations, we use a numerical algorithm that furnishes an evaluation of the precipitated fraction, the mean radius and the whole size distribution of the particles. The parameters that are the interface energy, the solubility product and the diffusion coefficients are fitted with the data available in the literature and our experimental results. It allows a satisfactory agreement as regards to the simplicity of the model. Monte Carlo simulations are used to describe the evolution of a ternary alloy Fe-Nb-C on a cubic centred rigid lattice with vacancy and interstitial mechanisms. This is realized with an atomistic description of the atoms jumps and their related frequencies. The model parameters are fitted with phase diagrams and diffusion coefficients. For the sake of simplicity, we consider that the precipitation of NbC is totally coherent and we neglect any elastic strain effect. We can observe different kinetic paths: for low supersaturations, we find an expected precipitation of NbC but for higher supersaturations, the very fast diffusivity of carbon atoms conducts to the nucleation of iron carbide particles. We establish that the occurrence of this second phenomenon depends on the vacancy arrival kinetics and can be related

Peculiarities of component interaction in {l_brace}Gd, Er{r_brace}-V-Sn Ternary systems at 870 K and crystal structure of RV{sub 6}Sn{sub 6} stannides

Energy Technology Data Exchange (ETDEWEB)

Romaka, L., E-mail: romakal@franko.lviv.ua [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya str. 6, 79005 Lviv (Ukraine); Stadnyk, Yu. [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya str. 6, 79005 Lviv (Ukraine); Romaka, V.V. [Department of Materials Engineering and Applied Physics, Lviv Polytechnic National University, Ustyyanovycha Str. 5, 79013 Lviv (Ukraine); Demchenko, P.; Stadnyshyn, M.; Konyk, M. [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya str. 6, 79005 Lviv (Ukraine)

2011-09-08

Highlights: > {l_brace}Gd, Er{r_brace}-V-Sn ternary systems at 870 K are characterized by formation of stannides with general compositions RV{sub 6}Sn{sub 6}. > Isostructural RV{sub 6}Sn{sub 6} compounds were also found with Y, Dy, Ho, Tm, and Lu. > The crystal structure of RV{sub 6}Sn{sub 6} compounds was determined by powder diffraction method. > Structural analysis showed that RV{sub 6}Sn{sub 6} compounds (R = Gd, Dy-Tm, Lu) are disordered; YV{sub 6}Sn{sub 6} is characterized by structure ordering. - Abstract: The phase equilibria in the Gd-V-Sn and Er-V-Sn ternary systems were studied at 870 K by means of X-ray and metallographic analyses in the whole concentration range. Both Gd-V-Sn and Er-V-Sn systems are characterized by formation of one ternary compound at investigated temperature, with stoichiometry RV{sub 6}Sn{sub 6} (SmMn{sub 6}Sn{sub 6}-type, space group P6/mmm, a = 0.55322(3) nm, c = 0.91949(7) nm for Gd, a = 0.55191(2) nm, c = 0.91869(8) nm for Er). Solubility of the third component in the binary compounds was not observed. Compounds with the SmMn{sub 6}Sn{sub 6}-type were also found with Dy, Ho, Tm, and Lu, while YV{sub 6}Sn{sub 6} compound crystallizes in HfFe{sub 6}Ge{sub 6} structure type. All investigated compounds are the first ternary stannides with rare earth elements and vanadium.

Shock Response of Boron Carbide

National Research Council Canada - National Science Library

Dandekar, D. P. (Dattatraya Purushottam)

2001-01-01

.... The present work was undertaken to determine tensile/spall strength of boron carbide under plane shock wave loading and to analyze all available shock compression data on boron carbide materials...

Stability and attractive basins of multiple equilibria in delayed two-neuron networks

International Nuclear Information System (INIS)

Huang Yu-Jiao; Zhang Hua-Guang; Wang Zhan-Shan

2012-01-01

Multiple stability for two-dimensional delayed recurrent neural networks with piecewise linear activation functions of 2r (r ≥ 1) corner points is studied. Sufficient conditions are established for checking the existence of (2r + 1) 2 equilibria in delayed recurrent neural networks. Under these conditions, (r + 1) 2 equilibria are locally exponentially stable, and (2r + 1) 2 — (r + 1) 2 — r 2 equilibria are unstable. Attractive basins of stable equilibria are estimated, which are larger than invariant sets derived by decomposing state space. One example is provided to illustrate the effectiveness of our results. (general)

Joining elements of silicon carbide

International Nuclear Information System (INIS)

Olson, B.A.

1979-01-01

A method of joining together at least two silicon carbide elements (e.g.in forming a heat exchanger) is described, comprising subjecting to sufficiently non-oxidizing atmosphere and sufficiently high temperature, material placed in space between the elements. The material consists of silicon carbide particles, carbon and/or a precursor of carbon, and silicon, such that it forms a joint joining together at least two silicon carbide elements. At least one of the elements may contain silicon. (author)

Vapor-liquid equilibria for nitric acid-water and plutonium nitrate-nitric acid-water solutions

International Nuclear Information System (INIS)

Maimoni, A.

1980-01-01

The liquid-vapor equilibrium data for nitric acid and nitric acid-plutnonium nitrate-water solutions were examined to develop correlations covering the range of conditions encountered in nuclear fuel reprocessing. The scanty available data for plutonium nitrate solutions are of poor quality but allow an order of magnitude estimate to be made. A formal thermodynamic analysis was attempted initially but was not successful due to the poor quality of the data as well as the complex chemical equilibria involved in the nitric acid and in the plutonium nitrate solutions. Thus, while there was no difficulty in correlating activity coefficients for nitric acid solutions over relatively narrow temperature ranges, attempts to extend the correlations over the range 25 0 C to the boiling point were not successful. The available data were then analyzed using empirical correlations from which normal boiling points and relative volatilities can be obtained over the concentration ranges 0 to 700 g/l Pu, 0 to 13 M nitric acid. Activity coefficients are required, however, if estimates of individual component vapor pressures are needed. The required ternary activity coefficients can be approximated from the correlations

Computation of Stackelberg Equilibria of Finite Sequential Games

DEFF Research Database (Denmark)

Bosanski, Branislav; Branzei, Simina; Hansen, Kristoffer Arnsfelt

2015-01-01

The Stackelberg equilibrium is a solution concept that describes optimal strategies to commit to: Player~1 (the leader) first commits to a strategy that is publicly announced, then Player~2 (the follower) plays a best response to the leader's choice. We study Stackelberg equilibria in finite...... sequential (i.e., extensive-form) games and provide new exact algorithms, approximate algorithms, and hardness results for finding equilibria for several classes of such two-player games....

Method of fabricating porous silicon carbide (SiC)

Science.gov (United States)

Shor, Joseph S. (Inventor); Kurtz, Anthony D. (Inventor)

1995-01-01

Porous silicon carbide is fabricated according to techniques which result in a significant portion of nanocrystallites within the material in a sub 10 nanometer regime. There is described techniques for passivating porous silicon carbide which result in the fabrication of optoelectronic devices which exhibit brighter blue luminescence and exhibit improved qualities. Based on certain of the techniques described porous silicon carbide is used as a sacrificial layer for the patterning of silicon carbide. Porous silicon carbide is then removed from the bulk substrate by oxidation and other methods. The techniques described employ a two-step process which is used to pattern bulk silicon carbide where selected areas of the wafer are then made porous and then the porous layer is subsequently removed. The process to form porous silicon carbide exhibits dopant selectivity and a two-step etching procedure is implemented for silicon carbide multilayers.

On Pure and (approximate) Strong Equilibria of Facility Location Games

DEFF Research Database (Denmark)

Hansen, Thomas Dueholm; Telelis, Orestis A.

2008-01-01

We study social cost losses in Facility Location games, where n selfish agents install facilities over a network and connect to them, so as to forward their local demand (expressed by a non-negative weight per agent). Agents using the same facility share fairly its installation cost, but every...... agent pays individually a (weighted) connection cost to the chosen location. We study the Price of Stability (PoS) of pure Nash equilibria and the Price of Anarchy of strong equilibria (SPoA), that generalize pure equilibria by being resilient to coalitional deviations. For unweighted agents on metric...

Design of a novel quantum reversible ternary up-counter

Science.gov (United States)

Houshmand, Pouran; Haghparast, Majid

2015-08-01

Reversible logic has been recently considered as an interesting and important issue in designing combinational and sequential circuits. The combination of reversible logic and multi-valued logic can improve power dissipation, time and space utilization rate of designed circuits. Only few works have been reported about sequential reversible circuits and almost there are no paper exhibited about quantum ternary reversible counter. In this paper, first we designed 2-qutrit and 3-qutrit quantum reversible ternary up-counters using quantum ternary reversible T-flip-flop and quantum reversible ternary gates. Then we proposed generalized quantum reversible ternary n-qutrit up-counter. We also introduced a new approach for designing any type of n-qutrit ternary and reversible counter. According to the results, we can conclude that applying second approach quantum reversible ternary up-counter is better than the others.

Characterization of Nanometric-Sized Carbides Formed During Tempering of Carbide-Steel Cermets

Directory of Open Access Journals (Sweden)

Matus K.

2016-06-01

Full Text Available The aim of this article of this paper is to present issues related to characterization of nanometric-sized carbides, nitrides and/or carbonitrides formed during tempering of carbide-steel cermets. Closer examination of those materials is important because of hardness growth of carbide-steel cermet after tempering. The results obtained during research show that the upswing of hardness is significantly higher than for high-speed steels. Another interesting fact is the displacement of secondary hardness effect observed for this material to a higher tempering temperature range. Determined influence of the atmosphere in the sintering process on precipitations formed during tempering of carbide-steel cermets. So far examination of carbidesteel cermet produced by powder injection moulding was carried out mainly in the scanning electron microscope. A proper description of nanosized particles is both important and difficult as achievements of nanoscience and nanotechnology confirm the significant influence of nanocrystalline particles on material properties even if its mass fraction is undetectable by standard methods. The following research studies have been carried out using transmission electron microscopy, mainly selected area electron diffraction and energy dispersive spectroscopy. The obtained results and computer simulations comparison were made.

Phase relations in the system NaCl-KCl-H2O: IV. Differential thermal analysis of the sylvite liquidus in the KCl-H2O binary, the liquidus in the NaCl-KCl-H2O ternary, and the solidus in the NaCl-KCl binary to 2 kb pressure, and a summary of experimental data for thermodynamic-PTX analysis of solid-liquid equilibria at elevated P-T conditions

Science.gov (United States)

Chou, I.-Ming; Sterner, S.M.; Pitzer, Kenneth S.

1992-01-01

The sylvite liquidus in the binary system KCl-H2O and the liquidus in the ternary system NaCl-KCl-H2O were determined by using isobaric differential thermal analysis (DTA) cooling scans at pressures up to 2 kbars. Sylvite solubilities along the three-phase curve in the binary system KCl-H2O were obtained by the intersection of sylvite-liquidus isopleths with the three-phase curve in a P-T plot. These solubility data can be represented by the equation Wt.% KCl (??0.2) = 12.19 + 0.1557T - 5.4071 ?? 10-5 T2, where 400 ??? T ??? 770??C. These data are consistent with previous experimental observations. The solidus in the binary system NaCl-KCl was determined by using isobaric DTA heating scans at pressures up to 2 kbars. Using these liquidus and solidus data and other published information, a thermodynamic-PTX analysis of solid-liquid equilibria at high pressures and temperatures for the ternary system has been performed and is presented in an accompanying paper (Part V of this series). However, all experimental liquidus, solidus, and solvus data used in this analysis are summarized in this report (Part IV) and they are compared with the calculated values based on the analysis. ?? 1992.

Numerical computation of FCT equilibria by inverse equilibrium method

International Nuclear Information System (INIS)

Tokuda, Shinji; Tsunematsu, Toshihide; Takeda, Tatsuoki

1986-11-01

FCT (Flux Conserving Tokamak) equilibria were obtained numerically by the inverse equilibrium method. The high-beta tokamak ordering was used to get the explicit boundary conditions for FCT equilibria. The partial differential equation was reduced to the simultaneous quasi-linear ordinary differential equations by using the moment method. The regularity conditions for solutions at the singular point of the equations can be expressed correctly by this reduction and the problem to be solved becomes a tractable boundary value problem on the quasi-linear ordinary differential equations. This boundary value problem was solved by the method of quasi-linearization, one of the shooting methods. Test calculations show that this method provides high-beta tokamak equilibria with sufficiently high accuracy for MHD stability analysis. (author)

Effect of alkanolammonium formates ionic liquids on vapour liquid equilibria of binary systems containing water, methanol, and ethanol

International Nuclear Information System (INIS)

Li Xuemei; Shen Chong; Li Chunxi

2012-01-01

Highlights ► Vapour pressures for six ternary systems containing an IL were measured. ► Components studied were water, ethanol, methanol, and alkanolammonium formates. ► The isobaric VLE were predicted using the fitted binary NRTL parameters. ► The ILs studied can generate a promising salt effect on VLE of azeotrope. ► [HMEA][HCOO] might be used as a potential entrainer in extractive distillation. - Abstract: Vapour pressures were measured using a quasi-static ebulliometer for the pseudo-binary mixtures of (water + ethanol), (water + methanol), and (methanol + ethanol) containing an alkanolammonium-based ionic liquid (IL), namely, mono-ethanolammonium formate ([HMEA][HCOO]) and di-ethanolammonium formate ([HDEA][HCOO]), respectively, with fixed IL mass fraction of 0.30 and over the temperature ranges of (292.12 to 371.13) K. The vapour pressures of the IL-containing ternary systems were favourably correlated using the NRTL model with an overall average absolute relative deviation (AARD) of 0.0082. Further, the salt effects of [HMEA][HCOO] and [HDEA][HCOO] on isobaric vapour liquid equilibria (VLE) of azeotrope and close boiling mixture, especially for the mixtures of (water + ethanol) and (methanol + ethanol), were investigated and compared with other ILs in terms of the x′–y phase diagrams predicted with the binary NRTL parameters. It is demonstrated that the relative volatilities of ethanol to water and ethanol to methanol are enhanced, and [HMEA][HCOO] might be used as a promising entrainer for the efficient separation of ethanol aqueous solution by special rectification.

Institutions, Equilibria and Efficiency

DEFF Research Database (Denmark)

Competition and efficiency is at the core of economic theory. This volume collects papers of leading scholars, which extend the conventional general equilibrium model in important ways. Efficiency and price regulation are studied when markets are incomplete and existence of equilibria in such set......Competition and efficiency is at the core of economic theory. This volume collects papers of leading scholars, which extend the conventional general equilibrium model in important ways. Efficiency and price regulation are studied when markets are incomplete and existence of equilibria...... in such settings is proven under very general preference assumptions. The model is extended to include geographical location choice, a commodity space incorporating manufacturing imprecision and preferences for club-membership, schools and firms. Inefficiencies arising from household externalities or group...... membership are evaluated. Core equivalence is shown for bargaining economies. The theory of risk aversion is extended and the relation between risk taking and wealth is experimentally investigated. Other topics include: determinacy in OLG with cash-in-advance constraints, income distribution and democracy...

Field line diversion properties of finite β-helias equilibria

International Nuclear Information System (INIS)

Hayashi, Takaya; Schwenn, Ulrich; Strumberger, Erika.

1992-01-01

The diversion properties of the magnetic field outside the last closed magnetic surface of a Helias stellarator configuration are investigated for finite pressure equilibria. The results indicate that a divertor concept which has been developed from the diversion properties of the corresponding vacuum field can be maintained for finite pressure equilibria. Cross-field particle transport is simulated by a simplified scrape-off layer (SOL) model. (author)

Ideal MHD beta-limits of poloidally asymmetric equilibria

Energy Technology Data Exchange (ETDEWEB)

Todd, A.M.M.; Miller, A.E.; Grimm, R.C.; Okabayashi, M.; Dalhed, H.E. Jr.

1981-05-01

The ideal MHD stability of poloidally asymmetric equilibria, which are typical of a tokamak reactor design with a single-null poloidal divertor is examined. As with symmetric equilibria, stability to non-axisymmetric modes improves with increasing triangularity and ellipticity, and with lower edge safety factor. Pressure profiles optimized with respect to ballooning stability are obtained for an asymmetric shape, resulting in ..beta../sub critical/ approx. = 5.7%. The corresponding value for an equivalent symmetric shape is ..beta../sub critical/ approx. = 6.5%.

Ideal MHD beta-limits of poloidally asymmetric equilibria

International Nuclear Information System (INIS)

Todd, A.M.M.; Miller, A.E.; Grimm, R.C.; Okabayashi, M.; Dalhed, H.E. Jr.

1981-05-01

The ideal MHD stability of poloidally asymmetric equilibria, which are typical of a tokamak reactor design with a single-null poloidal divertor is examined. As with symmetric equilibria, stability to non-axisymmetric modes improves with increasing triangularity and ellipticity, and with lower edge safety factor. Pressure profiles optimized with respect to ballooning stability are obtained for an asymmetric shape, resulting in β/sub critical/ approx. = 5.7%. The corresponding value for an equivalent symmetric shape is β/sub critical/ approx. = 6.5%

New Icosahedral Boron Carbide Semiconductors

Science.gov (United States)

Echeverria Mora, Elena Maria

Novel semiconductor boron carbide films and boron carbide films doped with aromatic compounds have been investigated and characterized. Most of these semiconductors were formed by plasma enhanced chemical vapor deposition. The aromatic compound additives used, in this thesis, were pyridine (Py), aniline, and diaminobenzene (DAB). As one of the key parameters for semiconducting device functionality is the metal contact and, therefore, the chemical interactions or band bending that may occur at the metal/semiconductor interface, X-ray photoemission spectroscopy has been used to investigate the interaction of gold (Au) with these novel boron carbide-based semiconductors. Both n- and p-type films have been tested and pure boron carbide devices are compared to those containing aromatic compounds. The results show that boron carbide seems to behave differently from other semiconductors, opening a way for new analysis and approaches in device's functionality. By studying the electrical and optical properties of these films, it has been found that samples containing the aromatic compound exhibit an improvement in the electron-hole separation and charge extraction, as well as a decrease in the band gap. The hole carrier lifetimes for each sample were extracted from the capacitance-voltage, C(V), and current-voltage, I(V), curves. Additionally, devices, with boron carbide with the addition of pyridine, exhibited better collection of neutron capture generated pulses at ZERO applied bias, compared to the pure boron carbide samples. This is consistent with the longer carrier lifetimes estimated for these films. The I-V curves, as a function of external magnetic field, of the pure boron carbide films and films containing DAB demonstrate that significant room temperature negative magneto-resistance (> 100% for pure samples, and > 50% for samples containing DAB) is possible in the resulting dielectric thin films. Inclusion of DAB is not essential for significant negative magneto

Mathematical Model for Multicomponent Adsorption Equilibria Using Only Pure Component Data

DEFF Research Database (Denmark)

Marcussen, Lis

2000-01-01

A mathematical model for nonideal adsorption equilibria in multicomponent mixtures is developed. It is applied with good results for pure substances and for prediction of strongly nonideal multicomponent equilibria using only pure component data. The model accounts for adsorbent...

Stable carbides in transition metal alloys

International Nuclear Information System (INIS)

Piotrkowski, R.

1991-01-01

In the present work different techniques were employed for the identification of stable carbides in two sets of transition metal alloys of wide technological application: a set of three high alloy M2 type steels in which W and/or Mo were total or partially replaced by Nb, and a Zr-2.5 Nb alloy. The M2 steel is a high speed steel worldwide used and the Zr-2.5 Nb alloy is the base material for the pressure tubes in the CANDU type nuclear reactors. The stability of carbide was studied in the frame of Goldschmidt's theory of interstitial alloys. The identification of stable carbides in steels was performed by determining their metallic composition with an energy analyzer attached to the scanning electron microscope (SEM). By these means typical carbides of the M2 steel, MC and M 6 C, were found. Moreover, the spatial and size distribution of carbide particles were determined after different heat treatments, and both microstructure and microhardness were correlated with the appearance of the secondary hardening phenomenon. In the Zr-Nb alloy a study of the α and β phases present after different heat treatments was performed with optical and SEM metallographic techniques, with the guide of Abriata and Bolcich phase diagram. The α-β interphase boundaries were characterized as short circuits for diffusion with radiotracer techniques and applying Fisher-Bondy-Martin model. The precipitation of carbides was promoted by heat treatments that produced first the C diffusion into the samples at high temperatures (β phase), and then the precipitation of carbide particles at lower temperature (α phase or (α+β)) two phase field. The precipitated carbides were identified as (Zr, Nb)C 1-x with SEM, electron microprobe and X-ray diffraction techniques. (Author) [es

Performance Estimation for Lowpass Ternary Filters

Directory of Open Access Journals (Sweden)

Brenton Steele

2003-11-01

Full Text Available Ternary filters have tap values limited to −1, 0, or +1. This restriction in tap values greatly simplifies the multipliers required by the filter, making ternary filters very well suited to hardware implementations. Because they incorporate coarse quantisation, their performance is typically limited by tap quantisation error. This paper derives formulae for estimating the achievable performance of lowpass ternary filters, thereby allowing the number of computationally intensive design iterations to be reduced. Motivated by practical communications systems requirements, the performance measure which is used is the worst-case stopband attenuation.

Ternary gradient metal-organic frameworks.

Science.gov (United States)

Liu, Chong; Rosi, Nathaniel L

2017-09-08

Gradient MOFs contain directional gradients of either structure or functionality. We have successfully prepared two ternary gradient MOFs based on bMOF-100 analogues, namely bMOF-100/102/106 and bMOF-110/100/102, via cascade ligand exchange reactions. The cubic unit cell parameter discrepancy within an individual ternary gradient MOF crystal is as large as ∼1 nm, demonstrating the impressive compatibility and flexibility of the component MOF materials. Because of the presence of a continuum of unit cells, the pore diameters within individual crystals also change in a gradient fashion from ∼2.5 nm to ∼3.0 nm for bMOF-100/102/106, and from ∼2.2 nm to ∼2.7 nm for bMOF-110/100/102, indicating significant porosity gradients. Like previously reported binary gradient MOFs, the composition of the ternary gradient MOFs can be easily controlled by adjusting the reaction conditions. Finally, X-ray diffraction and microspectrophotometry were used to analyse fractured gradient MOF crystals by comparing unit cell parameters and absorbance spectra at different locations, thus revealing the profile of heterogeneity (i.e. gradient distribution of properties) and further confirming the formation of ternary gradient MOFs.

Design of ternary clocked adiabatic static random access memory

International Nuclear Information System (INIS)

Wang Pengjun; Mei Fengna

2011-01-01

Based on multi-valued logic, adiabatic circuits and the structure of ternary static random access memory (SRAM), a design scheme of a novel ternary clocked adiabatic SRAM is presented. The scheme adopts bootstrapped NMOS transistors, and an address decoder, a storage cell and a sense amplifier are charged and discharged in the adiabatic way, so the charges stored in the large switch capacitance of word lines, bit lines and the address decoder can be effectively restored to achieve energy recovery during reading and writing of ternary signals. The PSPICE simulation results indicate that the ternary clocked adiabatic SRAM has a correct logic function and low power consumption. Compared with ternary conventional SRAM, the average power consumption of the ternary adiabatic SRAM saves up to 68% in the same conditions. (semiconductor integrated circuits)

Design of ternary clocked adiabatic static random access memory

Science.gov (United States)

Pengjun, Wang; Fengna, Mei

2011-10-01

Based on multi-valued logic, adiabatic circuits and the structure of ternary static random access memory (SRAM), a design scheme of a novel ternary clocked adiabatic SRAM is presented. The scheme adopts bootstrapped NMOS transistors, and an address decoder, a storage cell and a sense amplifier are charged and discharged in the adiabatic way, so the charges stored in the large switch capacitance of word lines, bit lines and the address decoder can be effectively restored to achieve energy recovery during reading and writing of ternary signals. The PSPICE simulation results indicate that the ternary clocked adiabatic SRAM has a correct logic function and low power consumption. Compared with ternary conventional SRAM, the average power consumption of the ternary adiabatic SRAM saves up to 68% in the same conditions.

Microsegregation in Nodular Cast Iron with Carbides

Directory of Open Access Journals (Sweden)

S. Pietrowski

2012-12-01

Full Text Available In this paper results of microsegregation in the newly developed nodular cast iron with carbides are presented. To investigate the pearlitic and bainitic cast iron with carbides obtained by Inmold method were chosen. The distribution of linear elements on the eutectic cell radius was examined. To investigate the microsegregation pearlitic and bainitic cast iron with carbides obtained by Inmold method were chosen.The linear distribution of elements on the eutectic cell radius was examined. Testing of the chemical composition of cast iron metal matrix components, including carbides were carried out. The change of graphitizing and anti-graphitizing element concentrations within eutectic cell was determined. It was found, that in cast iron containing Mo carbides crystallizing after austenite + graphite eutectic are Si enriched.

Microsegregation in Nodular Cast Iron with Carbides

Directory of Open Access Journals (Sweden)

Pietrowski S.

2012-12-01

Full Text Available In this paper results of microsegregation in the newly developed nodular cast iron with carbides are presented. To investigate the pearlitic and bainitic cast iron with carbides obtained by Inmold method were chosen. The distribution of linear elements on the eutectic cell radius was examined. To investigate the microsegregation pearlitic and bainitic cast iron with carbides obtained by Inmold method were chosen. The linear distribution of elements on the eutectic cell radius was examined. Testing of the chemical composition of cast iron metal matrix components, including carbides were carried out. The change of graphitizing and anti-graphitizing element concentrations within eutectic cell was determined. It was found, that in cast iron containing Mo carbides crystallizing after austenite + graphite eutectic are Si enriched.

The influence of the oxygen partial pressure on the quasi-ternary system Cr-Mn-Ti-oxide

International Nuclear Information System (INIS)

Garcia-Rosales, C.; Schulze, H.A.; Naoumidis, A.; Nickel, H.

1991-05-01

The passivation layers formed by the oxidizing corrosion of high temperature alloys consist primarily of oxides and mixed oxides of the elements chromium, manganese and titanium. For a reproducible formation and characterization of such oxide layers it is necessary to know the phase equilibria of these oxide systems at temperature and oxygen partial pressure conditions which will be relevant during their application. For the investigation of the quasi-ternary system Cr-Mn-Ti-oxide, oxide powders were prepared and annealed at 1000deg C under different oxygen partial pressures ranging from 0.21 bar to 10 -21 bar. Phase identification and determination of lattice parameter using X-ray diffraction analysis as well as the direct measurement of phase boundaries as a function of oxygen partial pressure using the emf-methode were carried out for these investigations. In the quasi-ternary system Cr-Mn-Ti-oxide the spinels play a decisive role in the oxigen partial pressure range examined. The spinel MnCr 2 O 4 may be regarded as the most significant compound. Part of the chronium can be replaced by trivalent manganese at high oxygen partial pressures and by trivalent titanium at low pressures, and the formation of a solid solution with the spinel Mn 2 TiO 4 is possible in all cases. In this way a coherent single-phase spinel region is observed which extends over the entire oxygen partial pressure range form 0.21 bar to 10 -21 bar examined at 1000deg C. (orig.) [de

Phase equilibria in the Mo-Fe-P system at 800 °C and structure of ternary phosphide (Mo(1-x)Fe(x))3P (0.10 ≤ x ≤ 0.15).

Science.gov (United States)

Oliynyk, Anton O; Lomnytska, Yaroslava F; Dzevenko, Mariya V; Stoyko, Stanislav S; Mar, Arthur

2013-01-18

Construction of the isothermal section in the metal-rich portion (ternary phases: (Mo(1-x)Fe(x))(2)P (x = 0.30-0.82) and (Mo(1-x)Fe(x))(3)P (x = 0.10-0.15). The occurrence of a Co(2)Si-type ternary phase (Mo(1-x)Fe(x))(2)P, which straddles the equiatomic composition MoFeP, is common to other ternary transition-metal phosphide systems. However, the ternary phase (Mo(1-x)Fe(x))(3)P is unusual because it is distinct from the binary phase Mo(3)P, notwithstanding their similar compositions and structures. The relationship has been clarified through single-crystal X-ray diffraction studies on Mo(3)P (α-V(3)S-type, space group I42m, a = 9.7925(11) Å, c = 4.8246(6) Å) and (Mo(0.85)Fe(0.15))(3)P (Ni(3)P-type, space group I4, a = 9.6982(8) Å, c = 4.7590(4) Å) at -100 °C. Representation in terms of nets containing fused triangles provides a pathway to transform these closely related structures through twisting. Band structure calculations support the adoption of these structure types and the site preference of Fe atoms. Electrical resistivity measurements on (Mo(0.85)Fe(0.15))(3)P reveal metallic behavior but no superconducting transition.

Alumina-Forming Austenitic Stainless Steels Strengthened by Laves Phase and MC Carbide Precipitates

Science.gov (United States)

Yamamoto, Y.; Brady, M. P.; Lu, Z. P.; Liu, C. T.; Takeyama, M.; Maziasz, P. J.; Pint, B. A.

2007-11-01

Creep strengthening of Al-modified austenitic stainless steels by MC carbides or Fe2Nb Laves phase was explored. Fe-20Cr-15Ni-(0-8)Al and Fe-15Cr-20Ni-5Al base alloys (at. pct) with small additions of Nb, Mo, W, Ti, V, C, and B were cast, thermally-processed, and aged. On exposure from 650 °C to 800 °C in air and in air with 10 pct water vapor, the alloys exhibited continuous protective Al2O3 scale formation at an Al level of only 5 at. pct (2.4 wt pct). Matrices of the Fe-20Cr-15Ni-5Al base alloys consisted of γ (fcc) + α (bcc) dual phase due to the strong α-Fe stabilizing effect of the Al addition and exhibited poor creep resistance. However, adjustment of composition to the Fe-15Cr-20Ni-5Al base resulted in alloys that were single-phase γ-Fe and still capable of alumina scale formation. Alloys that relied solely on Fe2Nb Laves phase precipitates for strengthening exhibited relatively low creep resistance, while alloys that also contained MC carbide precipitates exhibited creep resistance comparable to that of commercially available heat-resistant austenitic stainless steels. Phase equilibria studies indicated that NbC precipitates in combination with Fe2Nb were of limited benefit to creep resistance due to the solution limit of NbC within the γ-Fe matrix of the alloys studied. However, when combined with other MC-type strengtheners, such as V4C3 or TiC, higher levels of creep resistance were obtained.

Nash Equilibria in Symmetric Games with Partial Observation

DEFF Research Database (Denmark)

Bouyer, Patricia; Markey, Nicolas; Vester, Steen

2014-01-01

We investigate a model for representing large multiplayer games, which satisfy strong symmetry properties. This model is made of multiple copies of an arena; each player plays in his own arena, and can partially observe what the other players do. Therefore, this game has partial information...... and symmetry constraints, which make the computation of Nash equilibria difficult. We show several undecidability results, and for bounded-memory strategies, we precisely characterize the complexity of computing pure Nash equilibria (for qualitative objectives) in this game model....

High temperature evaporation of titanium, zirconium and hafnium carbides

International Nuclear Information System (INIS)

Gusev, A.I.; Rempel', A.A.

1991-01-01

Evaporation of cubic nonstoichiometric carbides of titanium, zirconium and hafnium in a comparatively low-temperature interval (1800-2700) with detailed crystallochemical sample certification is studied. Titanium carbide is characterized by the maximum evaporation rate: at T>2300 K it loses 3% of sample mass during an hour and at T>2400 K titanium carbide evaporation becomes extremely rapid. Zirconium and hafnium carbide evaporation rates are several times lower than titanium carbide evaporation rates at similar temperatures. Partial pressures of metals and carbon over the carbides studied are calculated on the base of evaporation rates

Recent progress in the relative equilibria of point vortices — In memoriam Hassan Aref

DEFF Research Database (Denmark)

Beelen, Peter; Brøns, Morten; Krishnamurthy, Vikas S.

2013-01-01

Hassan Aref, who sadly passed away in 2011, was one of the world's leading researchers in the dynamics and equilibria of point vortices. We review two problems on the subject of point vortex relative equilibria in which he was engaged at the time of his death: bilinear relative equilibria...

Synergistic increase of oxygen reduction favourable Fe-N coordination structures in a ternary hybrid of carbon nanospheres/carbon nanotubes/graphene sheets.

Science.gov (United States)

Zhang, Shiming; Liu, Bin; Chen, Shengli

2013-11-14

A Fe/N co-doped ternary nanocarbon hybrid, with uniform bamboo-like carbon nanotubes (CNTs) in situ grown on/between the single/few-layer graphene sheets interspaced by carbon nanosphere aggregates, was prepared through a one-pot heat treatment of a precursor mixture containing graphene oxide, Vulcan XC-72 carbon nanospheres, nitrogen rich melamine and small amounts of Fe ions. Physical characterization including electron microscopic images, N2 adsorption-desorption isotherms, pore size distribution, XPS, XRD, Mössbauer spectra, and EDX revealed that the 0-D/1-D/2-D ternary hybrid architecture not only offered an optimized morphology for high dispersion of each nanocarbon moiety, while the carbon nanosphere interspaced graphene sheets have provided a platform for efficient reaction between Fe ions and melamine molecules, resulting in uniform nucleation and growth of CNTs and formation of high density Fe-N coordination assemblies that have been believed to be the active centers for the oxygen reduction reaction (ORR) in carbon-based nonprecious metal electrocatalysts. In the absence of graphene oxides or carbon nanospheres, a similar heat treatment was found to result in large amounts of elemental Fe and Fe carbides and entangled CNTs with wide diameter distributions. As a result, the ternary Fe/N-doped nanocarbon hybrid exhibits ORR activity much higher than the Fe-N doped single or binary nanocarbon materials prepared under similar heat treatment conditions, and approaching that of the state-of-the-art carbon-supported platinum catalyst (Pt/C) in acidic media, as well as superior stability and methanol tolerance to Pt/C.

Variational-moment method for computing magnetohydrodynamic equilibria

International Nuclear Information System (INIS)

Lao, L.L.

1983-08-01

A fast yet accurate method to compute magnetohydrodynamic equilibria is provided by the variational-moment method, which is similar to the classical Rayleigh-Ritz-Galerkin approximation. The equilibrium solution sought is decomposed into a spectral representation. The partial differential equations describing the equilibrium are then recast into their equivalent variational form and systematically reduced to an optimum finite set of coupled ordinary differential equations. An appropriate spectral decomposition can make the series representing the solution coverge rapidly and hence substantially reduces the amount of computational time involved. The moment method was developed first to compute fixed-boundary inverse equilibria in axisymmetric toroidal geometry, and was demonstrated to be both efficient and accurate. The method since has been generalized to calculate free-boundary axisymmetric equilibria, to include toroidal plasma rotation and pressure anisotropy, and to treat three-dimensional toroidal geometry. In all these formulations, the flux surfaces are assumed to be smooth and nested so that the solutions can be decomposed in Fourier series in inverse coordinates. These recent developments and the advantages and limitations of the moment method are reviewed. The use of alternate coordinates for decomposition is discussed

Long-term Nash equilibria in electricity markets

International Nuclear Information System (INIS)

Pozo, David; Contreras, Javier; Caballero, Angel; de Andres, Antonio

2011-01-01

In competitive electricity markets, companies simultaneously offer their productions to obtain the maximum profits on a daily basis. In the long run, the strategies utilized by the electric companies lead to various long-term equilibria that can be analyzed with the appropriate tools. We present a methodology to find plausible long-term Nash equilibria in pool-based electricity markets. The methodology is based on an iterative market Nash equilibrium model in which the companies can decide upon their offer strategies. An exponential smoothing of the bids submitted by the companies is applied to facilitate the convergence of the iterative procedure. In each iteration of the model the companies face residual demand curves that are accurately modeled by Hermite interpolating polynomials. We introduce the concept of meta-game equilibrium strategies to allow companies to have a range of offer strategies where several pure and mixed meta-game Nash equilibria are possible. With our model it is also possible to model uncertainty or to generate price scenarios for financial models that assess the value of a generating unit by real options analysis. The application of the proposed methodology is illustrated with several realistic case studies. (author)

Reaction phases and diffusion paths in SiC/metal systems

Energy Technology Data Exchange (ETDEWEB)

Naka, M.; Fukai, T. [Osaka Univ., Osaka (Japan); Schuster, J.C. [Vienna Univ., Vienna (Austria)

2004-07-01

The interface structures between SiC and metal are reviewed at SiC/metal systems. Metal groups are divided to carbide forming metals and non-carbide forming metals. Carbide forming metals form metal carbide granular or zone at metal side, and metal silicide zone at SiC side. The further diffusion of Si and C from SiC causes the formation of T ternary phase depending metal. Non-carbide forming metals form silicide zone containing graphite or the layered structure of metal silicide and metal silicide containing graphite. The diffusion path between SiC and metal are formed along tie-lines connecting SiC and metal on the corresponding ternary Si-C-M system. The reactivity of metals is dominated by the forming ability of carbide or silicide. Te reactivity tendency of elements are discussed on the periodical table of elements, and Ti among elements shows the highest reactivity among carbide forming metals. For non-carbide forming metals the reactivity sequence of metals is Fe>Ni>Co. (orig.)

Tribological Characteristics of Tungsten Carbide Reinforced Arc Sprayed Coatings using Different Carbide Grain Size Fractions

Directory of Open Access Journals (Sweden)

W. Tillmann

2017-06-01

Full Text Available Tungsten carbide reinforced coatings play an important role in the field of surface engineering to protect stressed surfaces against wear. For thermally sprayed coatings, it is already shown that the tribological properties get mainly determined by the carbide grain size fraction. Within the scope of this study, the tribological characteristics of iron based WC-W2C reinforced arc sprayed coatings deposited using cored wires consisting of different carbide grain size fractions were examined. Microstructural characteristics of the produced coatings were scrutinized using electron microscopy and x-ray diffraction analyses. Ball-on-disk test as well as Taber Abraser and dry sand rubber wheel test were employed to analyze both the dry sliding and the abrasive wear behavior. It was shown that a reduced carbide grain size fraction as filling leads to an enhanced wear resistance against sliding. In terms of the Taber Abraser test, it is also demonstrated that a fine carbide grain size fraction results in an improved wear resistant against abrasion. As opposed to that, a poorer wear resistance was found within the dry sand rubber wheel tests. The findings show that the operating mechanisms for both abrasion tests affect the stressed surface in a different way, leading either to microcutting or microploughing.

The coloring problem in the solid-state metal boride carbide ScB{sub 2}C{sub 2}. A theoretical analysis

Energy Technology Data Exchange (ETDEWEB)

Lassoued, Souheila [Universite de Rennes, Ecole Nationale Superieure de Chimie, UMR 6226 CNRS (France). Inst. des Sciences Chimiques; Universite Kasdi Merbah-Ouargla (Algeria). Faculte des Mathematiques et des Sciences de la Matiere; Boucher, Benoit [Universite de Rennes, Ecole Nationale Superieure de Chimie, UMR 6226 CNRS (France). Inst. des Sciences Chimiques; Max-Planck-Institut fuer Chemische Physik Fester Stoffe, Dresden (Germany); Boutarfaia, Ahmed [Universite Kasdi Merbah-Ouargla (Algeria). Faculte des Mathematiques et des Sciences de la Matiere; Gautier, Regis; Halet, Jean-Francois [Universite de Rennes, Ecole Nationale Superieure de Chimie, UMR 6226 CNRS (France). Inst. des Sciences Chimiques

2016-08-01

The electronic properties of the layered ternary metal boride carbide ScB{sub 2}C{sub 2}, the structure of which consists of B/C layers made of fused five- and seven-membered rings alternating with scandium sheets, are analyzed. In particular, the respective positions of the B and C atoms (the so-called coloring problem) are tackled using density functional theory, quantum theory of atoms in molecules, and electron localizability indicator calculations. Results reveal that (i) the most stable coloring minimizes the number of B-B and C-C contacts and maximizes the number of boron atoms in the heptagons, (ii) the compound is metallic in character, and (iii) rather important covalent bonding occurs between the metallic sheets and the boron-carbon network.

Precipitation behavior of carbides in high-carbon martensitic stainless steel

Energy Technology Data Exchange (ETDEWEB)

Zhu, Qin-tian; Li, Jing; Shi, Cheng-bin; Yu, Wen-tao; Shi, Chang-min [University of Science and Technology, Beijing (China). State Key Laboratory of Advanced Metallurgy; Li, Ji-hui [Yang Jiang Shi Ba Zi Group Co., Ltd, Guangdong (China)

2017-01-15

A fundamental study on the precipitation behavior of carbides was carried out. Thermo-calc software, scanning electron microscopy, electron probe microanalysis, transmission electron microscopy, X-ray diffractometry and high-temperature confocal laser scanning microscopy were used to study the precipitation and transformation behaviors of carbides. Carbide precipitation was of a specific order. Primary carbides (M7C3) tended to be generated from liquid steel when the solid fraction reached 84 mol.%. Secondary carbides (M7C3) precipitated from austenite and can hardly transformed into M23C6 carbides with decreasing temperature in air. Primary carbides hardly changed once they were generated, whereas secondary carbides were sensitive to heat treatment and thermal deformation. Carbide precipitation had a certain effect on steel-matrix phase transitions. The segregation ability of carbon in liquid steel was 4.6 times greater that of chromium. A new method for controlling primary carbides is proposed.

Institutions, Equilibria and Efficiency

DEFF Research Database (Denmark)

Competition and efficiency is at the core of economic theory. This volume collects papers of leading scholars, which extend the conventional general equilibrium model in important ways. Efficiency and price regulation are studied when markets are incomplete and existence of equilibria in such set...... in OLG, learning in OLG and in games, optimal pricing of derivative securities, the impact of heterogeneity...

All-optical symmetric ternary logic gate

Science.gov (United States)

Chattopadhyay, Tanay

2010-09-01

Symmetric ternary number (radix=3) has three logical states (1¯, 0, 1). It is very much useful in carry free arithmetical operation. Beside this, the logical operation using this type of number system is also effective in high speed computation and communication in multi-valued logic. In this literature all-optical circuits for three basic symmetrical ternary logical operations (inversion, MIN and MAX) are proposed and described. Numerical simulation verifies the theoretical model. In this present scheme the different ternary logical states are represented by different polarized state of light. Terahertz optical asymmetric demultiplexer (TOAD) based interferometric switch has been used categorically in this manuscript.

Transition metal carbide and boride abrasive particles

International Nuclear Information System (INIS)

Valdsaar, H.

1978-01-01

Abrasive particles and their preparation are discussed. The particles consist essentially of a matrix of titanium carbide and zirconium carbide, at least partially in solid solution form, and grains of crystalline titanium diboride dispersed throughout the carbide matrix. These abrasive particles are particularly useful as components of grinding wheels for abrading steel. 1 figure, 6 tables

Ternary alloy systems. Phase diagrams, crystallographic and thermodynamic data critically evaluated by MSIT registered. Subvol. C. Non-ferrous metal systems. Pt. 4: Selected nuclear materials and engineering systems

International Nuclear Information System (INIS)

Effenberg, Guenter; Ilyenko, Svitlana; Aldinger, Fritz; Bochvar, Nataliya; Cacciamani, Gabriele

2007-01-01

The present volume in the New Series of Landolt-Boernstein provides critically evaluated data on phase diagrams, crystallographic and thermodynamic data of ternary alloy systems. Reliable phase diagrams provide materials scientists and engineers with basic information important for fundamental research, development and optimization of materials. The often conflicting literature data have been critically evaluated by Materials Science International Team, MSIT registered , a team working together since many years, and with expertise in a broad range of methods, materials and applications. All evaluation reports published here have undergone a thorough review process in which the reviewers had access to all the original data. The data for each ternary system are provided in a standard format which includes text, tables and diagrams. The topics presented are literature data, binary systems, solid phases, pseudobinary systems, invariant equilibria, liquidus, solidus, and solvus surfaces, isothermal sections, temperature-composition sections, thermodynamics, materials properties and applications, and miscellanea. Finally, a detailed bibliography of all cited references is provided. In the present volume IV/11C selected non-ferrous-metal systems are considered, especially selected nuclear materials and engineering systems in this Part 4. (orig.)

Thermodynamic modeling of the Ti-Al-Cr ternary system

International Nuclear Information System (INIS)

Chen Leyi; Qiu Aitao; Liu Lanjie; Jiang Ming; Lu Xionggang; Li Chonghe

2011-01-01

Research highlights: → The full experimental results of the Ti-Al-Cr ternary system and its sub-binary systems are reviewed and analysed in detail. → Based on the latest thermodynamic assessments of the Ti-Al, Ti-Cr and Al-Cr systems and the ternary experimental data in literature, the thermodynamic parameters of the Ti-Al-Cr ternary system are fully assessed by the Calphad method. → The transformation of disorder to order (bcc a 2 to B2) and the new ternary compound L 12T i 25 Cr 8 Al 67 are considered in this work. - Abstract: The Ti-Al-Cr ternary system is one of the most important systems to studying the titanium alloys. Some experimental data of this ternary system are available and a few partial thermodynamic assessments are reported. However, no full thermodynamic descriptions were published. In this study, the previous work on the Ti-Al-Cr system and its related binary systems are reviewed. Based on the thermodynamic descriptions of the Ti-Al, Ti-Cr and Al-Cr systems and the ternary experimental data in literature, the Ti-Al-Cr ternary system is assessed by means of the Calphad method. Several isothermal sections from 1073 K to 1573 K and some invariant reactions are calculated, which are in good agreement with the most of the experimental results.

On the uniqueness of fully informative rational expectations equilibria

OpenAIRE

Peter DeMarzo; Costis Skiadas

1998-01-01

This paper analyzes two equivalent equilibrium notions under asymmetric information: risk neutral rational expectations equilibria (rn-REE), and common knowledge equilibria. We show that the set of fully informative rn-REE is a singleton, and we provide necessary and sufficient conditions for the existence of partially informative rn-REE. In a companion paper (DeMarzo and Skiadas (1996)) we show that equilibrium prices for the larger class of quasi-complete economies can be characterized as r...

Magnetoacoustic heating and FCT-equilibria in the belt pinch

International Nuclear Information System (INIS)

Erckmann, V.

1983-02-01

In the HECTOR belt pinch of high β plasma is produced by magnetic compression in a Tokamak geometry. After compresseion the initial β value can be varied between 0.2 and 0.8. During 5 μs the plasma is further heated by a fast magnetoacoustic wave with a frequency near the first harmonic of the ion cyclotronfrequency. For the first time the β-value of a pinch plasma could be increased further from 0.34 after compression to 0.46 at the end of the rf-heating cycle. By proper selection of the final β-value the region for resonance absorption of the heating wave can be shifted. Strong heating (200 MW) has been observed in the cases, where the resonance region has been located in the center of the plasma. In deuterium discharges an increase in ion temperature is observed during the heating process, whereas the electrons are energetically decoupled, showing no temperature increase. Strong plasma losses are found in the 200 MW range after the rf-heating process. The dominant mechanisms are charge exchange collisions with neutral gas atoms. During rf-heating and the subsequent cooling phase the magnetic flux is frozen due to the high conductivity of the plasma. The observed equilibria could be identified as flux conserving Tokamak (FCT) equilibria. Based on a two-dimensional code the time-evolution of the equilibria has been calculated. The q-profiles are time-independent, with increasing β the magnetic axis of the plasma is shifted towards the outer boundary of the torus, and finally the linear relation between β and βsub(pol), which is characteristic for low-β-equilibria, is no longer valid. Thus for the first time the existence of FCT-equilibria at high β has been demonstrated experimentally together with a qualitative agreement with FCT-theory. (orig./AH) [de

A note on relative equilibria in a rotating shallow water layer

KAUST Repository

Ait Abderrahmane, Hamid

2013-05-08

Relative equilibria of two and three satellite vortices in a rotating shallow water layer have been recorded via particle image velocimetry (PIV) and their autorotation speed was estimated. This study shows that these equilibria retain the fundamental characteristics of Kelvin\\'s equilibria, and could be adequately described by the classical idealized point vortex theory. The same conclusion can also be inferred using the experimental dataset of Bergmann et al. (J. Fluid Mech., vol. 679, 2011, pp. 415-431; J. Fluid Mech., vol. 691, 2012, pp. 605-606) if the assigned field\\'s contribution to pattern rotation is included. © 2013 Cambridge University Press.

Experimental investigation of the Ag–Bi–I ternary system and thermodynamic properties of the ternary phases

International Nuclear Information System (INIS)

Mashadieva, Leyla F.; Aliev, Ziya S.; Shevelkov, Andrei V.; Babanly, Mahammad B.

2013-01-01

Highlights: ► The self-consistent phase diagram of the Ag–Bi–I system is constructed. ► Ag 2 BiI 5 and AgBi 2 I 7 are the only ternary phases of the system. ► Standard thermodynamic functions of formation and the standard entropies of Ag 2 BiI 5 and AgBi 2 I 7 are calculated. - Abstract: The phase equilibriums in the Ag–Bi–I ternary system and thermodynamic properties of the ternary phases were experimentally determined by using DTA and XRD techniques and EMF measurements with the Ag 4 RbI 5 solid electrolyte. According to the obtained experimental results, the polythermal sections of the ternary phase diagram, its isothermal section at 300 K as well as the projection of the liquids surface have been revised. The fields of the primary crystallization and types and coordinates of nonvariant and monovariant equilibriums were determined. The partial molar functions of silver iodide and silver in the alloys as well as the standard thermodynamic functions of formation and the standard entropies of Ag 2 BiI 5 and AgBi 2 I 7 were calculated based on EMF measurements.

Point defects and transport properties in carbides

International Nuclear Information System (INIS)

Matzke, Hj.

1984-01-01

Carbides of transition metals and of actinides are interesting and technologically important. The transition-metal carbides (or carbonitrides) are extensively being used as hard materials and some of them are of great interest because of the high transition temperature for superconductivity, e.g. 17 K for Nb(C,N). Actinide carbides and carbonitrides, (U,Pu)C and (U,Pu)(C,N) are being considered as promising advanced fuels for liquid metal cooled fast breeder nuclear reactors. Basic interest exists in all these materials because of their high melting points (e.g. 4250 K for TaC) and the unusually broad range of homogeneity of nonstoichiometric compositions (e.g. from UCsub(0.9) to UCsub(1.9) at 2500 K). Interaction of point defects to clusters and short-range ordering have recently been studied with elastic neutron diffraction and diffuse scattering techniques, and calculations of energies of formation and interaction of point defects became available for selected carbides. Diffusion measurements also exist for a number of carbides, in particular for the actinide carbides. The existing knowledge is discussed and summarized with emphasis on informative examples of particular technological relevance. (Auth.)

Feasibility of bio-based lactate esters as extractant for biobutanol recovery: (Liquid + liquid) equilibria

International Nuclear Information System (INIS)

Zheng, Shaohua; Cheng, Hongye; Chen, Lifang; Qi, Zhiwen

2016-01-01

Highlights: • Lactate esters were studied as solvent to remove butanol from aqueous media. • (Liquid + liquid) equilibrium data were measured at T = 298.15 K and 1 atm. • Selectivity and 1-butanol partition coefficient were calculated. • COSMO-based study of separation efficiency on solvent structure was conducted. - Abstract: As bio-based solvents, lactate esters can be used as extractant for removing 1-butanol from the aqueous fermentation broths. In order to evaluate the separation efficiency of butyl lactate and 2-ethylhexyl lactate for the extraction of 1-butanol from its mixture with water, the (liquid + liquid) equilibrium for the ternary systems {water (1) + 1-butanol (2) + lactate ester (3)} were measured at T = 298.15 K. The 1-butanol partition coefficient varied in the range of 4.46 to 10.29, and the solvent selectivity within 32.12 to 108.18. For the separation of low-concentration butanol from fermentation broths, butyl lactate exhibits higher partition coefficient and lower selectivity than 2-ethylhexyl lactate. The NRTL model was employed to correlate the experimental data, and the COSMO-RS theory was utilized to predict the (liquid + liquid) equilibria and to analyze the influence of lactate esters on extraction efficiency.

Liquid phase sintering of carbides using a nickel-molybdenum alloy

International Nuclear Information System (INIS)

Barranco, J.M.; Warenchak, R.A.

1987-01-01

Liquid phase vacuum sintering was used to densify four carbide groups. These were titanium carbide, tungsten carbide, vanadium carbide, and zirconium carbide. The liquid phase consisted of nickel with additions of molybdenum of from 6.25 to 50.0 weight percent at doubling increments. The liquid phase or binder comprised 10, 20, and 40 percent by weight of the pressed powders. The specimens were tested using 3 point bending. Tungsten carbide showed the greatest improvement in bend rupture strength, flexural modulus, fracture energy and hardness using 20 percent binder with lesser amounts of molybdenum (6.25 or 12.5 wt %) added to nickel compared to pure nickel. A refinement in the carbide microstructure and/or a reduction in porosity was seen for both the titanium and tungsten carbides when the alloy binder was used compared to using the nickel alone. Curves depicting the above properties are shown for increasing amounts of molybdenum in nickel for each carbide examined. Loss of binder phase due to evaporation was experienced during heating in vacuum at sintering temperatures. In an effort to reduce porosity, identical specimens were HIP processed at 15 ksi and temperatures averaging 110 C below the sintering g temperature. The tungsten carbide and titanium carbide series containing 80 and 90 weight percent carbide phase respectively showed improvement properties after HIP while properties decreased for most other compositions

Tungsten--carbide critical assembly

International Nuclear Information System (INIS)

Hansen, G.E.; Paxton, H.C.

1975-06-01

The tungsten--carbide critical assembly mainly consists of three close-fitting spherical shells: a highly enriched uranium shell on the inside, a tungsten--carbide shell surrounding it, and a steel shell on the outside. Ideal critical specifications indicate a rather low computed value of k/sub eff/. Observed and calculated fission-rate distributions for 235 U, 238 U, and 237 Np are compared, and calculated leakage neutrons per fission in various energy groups are given. (U.S.)

Extended vapor-liquid-solid growth of silicon carbide nanowires.

Science.gov (United States)

Rajesh, John Anthuvan; Pandurangan, Arumugam

2014-04-01

We developed an alloy catalytic method to explain extended vapor-liquid-solid (VLS) growth of silicon carbide nanowires (SiC NWs) by a simple thermal evaporation of silicon and activated carbon mixture using lanthanum nickel (LaNi5) alloy as catalyst in a chemical vapor deposition process. The LaNi5 alloy binary phase diagram and the phase relationships in the La-Ni-Si ternary system were play a key role to determine the growth parameters in this VLS mechanism. Different reaction temperatures (1300, 1350 and 1400 degrees C) were applied to prove the established growth process by experimentally. Scanning electron microscopy and transmission electron microscopy studies show that the crystalline quality of the SiC NWs increases with the temperature at which they have been synthesized. La-Ni alloyed catalyst particles observed on the top of the SiC NWs confirms that the growth process follows this extended VLS mechanism. The X-ray diffraction and confocal Raman spectroscopy analyses demonstrate that the crystalline structure of the SiC NWs was zinc blende 3C-SiC. Optical property of the SiC NWs was investigated by photoluminescence technique at room temperature. Such a new alloy catalytic method may be extended to synthesis other one-dimensional nanostructures.

True ternary fission of 252Cf

International Nuclear Information System (INIS)

Vijayaraghavan, K.R.; Balasubramaniam, M.; Oertzen, W. von

2014-01-01

Splitting of heavy radioactive nucleus into three fragments is known as ternary fission. If the size of the fragments are almost equal it is referred to as true ternary fission. Recently, Yu. V. Pyatkov et al observed/reported the experimental observation of true ternary fission in 252 Cf. In this work, the possibilities of different true ternary fission modes of 252 Cf through potential energy surface (PES) calculations based on three cluster model (TCM) are discussed. In TCM a condition on the mass numbers of the fission fragments is implied as A 1 ≥ A 2 ≥ A 3 in order to avoid repetition of combinations. Due to this condition, the values of Z 3 vary from 0 to 36 and Z 2 vary from 16 to 51. Of the different pairs having similar (Z 2 , Z 3 ) with different potential energy, a pair possessing minimum potential energy is chosen. Thus identified favourable combinations are plotted. For the PES calculations the arrangement of the fragments is considered in the order of A 1 +A 2 +A 3 . i.e. the heavy and the lightest fragments are kept at the ends. It is seen that the deepest minimum in the PES occurs for Z 3 =2 labelled as (Z 2 ; 2) indicating He accompanied breakup as the most favourable one. Of which, the breakup with Z 2 around 46 to 48 is the least (shown by dashed (Z 1 = 50) and dotted (Z 1 = 52) lines indicating a constant Z 1 value). The other notable minima in the PES are labelled and they correspond to the (Z 2 , Z 3 ) pairs viz., (20, 20), (28, 20), (28, 28) and (32, 32). Of these four minima, the first three are associated with the magic numbers 20 and 28. For Z 3 =20, there are two minimums at (20,20) and (28,20) among them (28,20) is the lowest minimum through which the minimum-path passes, and it is the ternary decay observed by Yu. V. Pyatkov et al. The fourth minima is the most interesting due to the fact that it corresponds to true ternary fission mode with Z 2 =32, Z 3 =32 and Z 1 =34. The minimum potential energy path also goes through this true

FLiNaK compatibility studies with Inconel 600 and silicon carbide

Energy Technology Data Exchange (ETDEWEB)

Yoder, Graydon L., E-mail: yodergljr@ornl.gov [Oak Ridge National Laboratory, Bldg. 5700, MS 6167 Bethel Valley Rd., Oak Ridge, TN 37831 (United States); Heatherly, Dennis; Wilson, Dane [Oak Ridge National Laboratory, Bldg. 5700, MS 6167 Bethel Valley Rd., Oak Ridge, TN 37831 (United States); Caja, Mario [Electrochemical Systems, Inc. (ESI), 9320 Collingwood Rd., Knoxville, TN 37922 (United States)

2016-10-15

Highlights: • A versatile experimental design has been developed to examine liquid fluoride salt materials compatibility behavior. • Samples of silicon carbide and a grafoil/nickel spiral wound gasket were exposed to FLiNaK salt at 700 °C for 90 days and showed no degradation. • Alloy 600 showed material effects penetrating up to 300 μm below the salt interface after exposure to the salt for 90 days at 700 °C. • Comparison of the Alloy 600 corrosion results with existing data indicated that results were comparable to the few corrosion results available for Alloy 600. • Sapphire viewing windows incorporated in the experiment showed fogging by condensed salt components at the highest test temperatures. - Abstract: A small liquid fluoride salt test apparatus has been constructed and testing has been conducted to examine the compatibility of silicon carbide (SiC), Inconel 600 and a spiral wound gasket material in FLiNaK, the ternary eutectic alkaline metal fluoride salt mixture. These tests were conducted to evaluate materials and sealing systems that could be used in fluoride salt systems. Three months of testing at 700 °C was conducted to assure that these materials and seals would be acceptable when operating under prototypic operating conditions. The SiC specimens showed little or no change over the test period, while the spiral wound gasket material did not show any degradation except that salt might have been seeping into the outermost spirals of the gasket. The Inconel 600 specimens showed regions of voiding which penetrated the specimen surface to about 250 μm in depth. Analysis indicated that the salt had leached chrome from the Inconel surface, as was expected for this material.

Plasma metallization of refractory carbide powders

International Nuclear Information System (INIS)

Koroleva, E.B.; Klinskaya, N.A.; Rybalko, O.F.; Ugol'nikova, T.A.

1986-01-01

The effect of treatment conditions in plasma on properties of produced metallized powders of titanium, tungsten and chromium carbides with the main particle size of 40-80 μm is considered. It is shown that plasma treatment permits to produce metallized powders of carbide materials with the 40-80 μm particle size. The degree of metallization, spheroidization, chemical and phase composition of metallized carbide powders are controlled by dispersivity of the treated material, concentration of a metal component in the treated mixtures, rate of plasma flow and preliminary spheroidization procedure

Ternary complex formation at mineral/solution interfaces

International Nuclear Information System (INIS)

Leckie, J.O.

1995-01-01

Adsorption of trace concentrations of radionuclides and heavy metals from aqueous solution is dependent on pH, absorbent and adsorbate concentration, and speciation of the metal in solution. In particular, complexation of metal ions by organic and inorganic ligands can dramatically alter adsorption behavior compared to ligand-free systems. The presence of complexing ligands can cause the formation of ''metal like'' or ''ligand like'' ternary surface complexes depending on whether adsorption of the ternary complex increases or decreases with increasing pH, respectively. Examples of ternary surface complexes behaving ''metal like'' include uranyl-EDTA surface complexes on goethite, neptunyl-EDTA surface complexes on hematite and neptunyl-humic surface complexes on gibbsite. Examples of ''ligand like'' ternary surface complexes include uranyl-carbonato and neptunyl-carbonato surface complexes on iron oxides. The effects of complex solutions and multimineralic systems are discussed. (authors). 39 refs., 16 figs., 8 tabs

Stackelberg equilibria and horizontal differentiation

OpenAIRE

Lambertini, Luca

1993-01-01

This paper proposes a taxonomy of the Stackelberg equilibria emerging from a standard game of horizontal differentiation à la Hotelling in which the strategy set of the sellers in the location stage is the real axis. Repeated leadership appears the most advantageous position. Furthermore, this endogenously yields vertical differentiation between products at equilibrium.

Phase equilibria and homogeneity range of the high temperature superconducting compound (Bi,Pb)2+xSr2Ca2Cu3O10+δ

International Nuclear Information System (INIS)

Kaesche, S.

1995-01-01

For the superconducting cuprates (Bi,Pb) 2+x Sr 2 Ca 2 Cu 3 O 10+y phase equilibria, the homogeneity region, and the phase formation has been studied in the temperture range 800 to 890 C. Sintered samples were prepared by a solid state reaction starting from Bi 2 O 3 , PbO, CuO and carbonates CaCO 3 and SrCO 3 in a three-stage calcination process. For the phase identification polarization microscopy, X-ray diffraction and susceptibility measurements have been applied. Multi-phase regions were determined in the cross section of the quasi-ternary system (Bi,Pb) 2 O 3 -SrO-CaO-CuO with constant Bi/(Bi+Pb) ratio 0.84 taking into account the 2223-phase. The homogeneity region was determined as function of Sr, Ca, Bi and Pb concentration. Its maximum size was found at 850 C

Ligand sphere conversions in terminal carbide complexes

DEFF Research Database (Denmark)

Morsing, Thorbjørn Juul; Reinholdt, Anders; Sauer, Stephan P. A.

2016-01-01

Metathesis is introduced as a preparative route to terminal carbide complexes. The chloride ligands of the terminal carbide complex [RuC(Cl)2(PCy3)2] (RuC) can be exchanged, paving the way for a systematic variation of the ligand sphere. A series of substituted complexes, including the first...... example of a cationic terminal carbide complex, [RuC(Cl)(CH3CN)(PCy3)2]+, is described and characterized by NMR, MS, X-ray crystallography, and computational studies. The experimentally observed irregular variation of the carbide 13C chemical shift is shown to be accurately reproduced by DFT, which also...... demonstrates that details of the coordination geometry affect the carbide chemical shift equally as much as variations in the nature of the auxiliary ligands. Furthermore, the kinetics of formation of the sqaure pyramidal dicyano complex, trans-[RuC(CN)2(PCy3)2], from RuC has been examined and the reaction...

Ternary networks reliability and Monte Carlo

CERN Document Server

Gertsbakh, Ilya; Vaisman, Radislav

2014-01-01

Ternary means “based on three”. This book deals with reliability investigations of  networks whose components subject to failures can be in three states –up, down and middle (mid), contrary to traditionally considered networks  having only binary (up/down) components. Extending binary case to ternary allows to consider more realistic and flexible models for communication, flow and supply networks.

Crystallization of nodular cast iron with carbides

Directory of Open Access Journals (Sweden)

S. Pietrowski

2008-12-01

Full Text Available In this paper a crystallization process of nodular cast iron with carbides having a different chemical composition have been presented. It have been found, that an increase of molybdenum above 0,30% causes the ledeburutic carbides crystallization after (γ+ graphite eutectic phase crystallization. When Mo content is lower, these carbides crystallize as a pre-eutectic phase. In this article causes of this effect have been given.

Ternary fission induced by polarized neutrons

Directory of Open Access Journals (Sweden)

Gönnenwein Friedrich

2013-12-01

Full Text Available Ternary fission of (e,e U- and Pu- isotopes induced by cold polarized neutrons discloses some new facets of the process. In the so-called ROT effect shifts in the angular distributions of ternary particles relative to the fission fragments show up. In the so-called TRI effect an asymmetry in the emission of ternary particles relative to a plane formed by the fragment momentum and the spin of the neutron appear. The two effects are shown to be linked to the components of angular momentum perpendicular and parallel to the fission axis at the saddle point of fission. Based on theoretical models the spectroscopic properties of the collective transitional states at the saddle point are inferred from experiment.

Thermodynamic Equilibria and Extrema Analysis of Attainability Regions and Partial Equilibria

CERN Document Server

Gorban, Alexander N; Kaganovich, Boris M; Keiko, Alexandre V; Shamansky, Vitaly A; Shirkalin, Igor A

2006-01-01

This book discusses mathematical models that are based on the concepts of classical equilibrium thermodynamics. They are intended for the analysis of possible results of diverse natural and production processes. Unlike the traditional models, these allow one to view the achievable set of partial equilibria with regards to constraints on kinetics, energy and mass exchange and to determine states of the studied systems of interest for the researcher. Application of the suggested models in chemical technology, energy and ecology is illustrated in the examples.

Determination of 3D Equilibria from Flux Surface Knowledge Only

International Nuclear Information System (INIS)

Mynick, H.E.; Pomphrey, N.

2001-01-01

We show that the method of Christiansen and Taylor, from which complete tokamak equilibria can be determined given only knowledge of the shape of the flux surfaces, can be extended to 3-dimensional equilibria, such as those of stellarators. As for the tokamak case, the given geometric knowledge has a high degree of redundancy, so that the full equilibrium can be obtained using only a small portion of that information

Preparation and Fatigue Properties of Functionally Graded Cemented Carbides

International Nuclear Information System (INIS)

Liu Yong; Liu Fengxiao; Liaw, Peter K.; He Yuehui

2008-01-01

Cemented carbides with a functionally graded structure have significantly improved mechanical properties and lifetimes in cutting, drilling and molding. In this work, WC-6 wt.% Co cemented carbides with three-layer graded structure (surface layer rich in WC, mid layer rich in Co and the inner part of the average composition) were prepared by carburizing pre-sintered η-phase-containing cemented carbides. The three-point bending fatigue tests based on the total-life approach were conducted on both WC-6wt%Co functionally graded cemented carbides (FGCC) and conventional WC-6wt%Co cemented carbides. The functionally graded cemented carbide shows a slightly higher fatigue limit (∼100 MPa) than the conventional ones under the present testing conditions. However, the fatigue crack nucleation behavior of FGCC is different from that of the conventional ones. The crack nucleates preferentially along the Co-gradient and perpendicular to the tension surface in FGCC, while parallel to the tension surface in conventional cemented carbides

Nash Equilibria in Symmetric Graph Games with Partial Observation

DEFF Research Database (Denmark)

Bouyer, Patricia; Markey, Nicolas; Vester, Steen

2017-01-01

We investigate a model for representing large multiplayer games, which satisfy strong symmetry properties. This model is made of multiple copies of an arena; each player plays in his own arena, and can partially observe what the other players do. Therefore, this game has partial information...... and symmetry constraints, which make the computation of Nash equilibria difficult. We show several undecidability results, and for bounded-memory strategies, we precisely characterize the complexity of computing pure Nash equilibria for qualitative objectives in this game model....

Indacenodithienothiophene-Based Ternary Organic Solar Cells

Energy Technology Data Exchange (ETDEWEB)

Gasparini, Nicola, E-mail: nicola.gasparini@fau.de [Institute of Materials for Electronics and Energy Technology (I-MEET), Friedrich-Alexander-University Erlangen-Nuremberg, Erlangen (Germany); García-Rodríguez, Amaranda [Macromolecular Chemistry Group (buwmakro), Institute for Polymer Technology, BergischeUniversität Wuppertal, Wuppertal (Germany); Prosa, Mario [Istituto per lo Studio dei Materiali Nanostrutturati (ISMN), Consiglio Nazionale delle Ricerche (CNR), Bologna (Italy); Bayseç, Şebnem; Palma-Cando, Alex [Macromolecular Chemistry Group (buwmakro), Institute for Polymer Technology, BergischeUniversität Wuppertal, Wuppertal (Germany); Katsouras, Athanasios; Avgeropoulos, Apostolos [Department of Materials Science Engineering, University of Ioannina, Ioannina (Greece); Pagona, Georgia; Gregoriou, Vasilis G. [Advent Technologies SA, Patras Science Park, Patra (Greece); National Hellenic Research Foundation (NHRF), Athens (Greece); Chochos, Christos L. [Department of Materials Science Engineering, University of Ioannina, Ioannina (Greece); Advent Technologies SA, Patras Science Park, Patra (Greece); Allard, Sybille; Scherf, Ulrich [Macromolecular Chemistry Group (buwmakro), Institute for Polymer Technology, BergischeUniversität Wuppertal, Wuppertal (Germany); Brabec, Christoph J. [Institute of Materials for Electronics and Energy Technology (I-MEET), Friedrich-Alexander-University Erlangen-Nuremberg, Erlangen (Germany); Bavarian Center for Applied Energy Research (ZAE Bayern), Erlangen (Germany); Ameri, Tayebeh, E-mail: nicola.gasparini@fau.de [Institute of Materials for Electronics and Energy Technology (I-MEET), Friedrich-Alexander-University Erlangen-Nuremberg, Erlangen (Germany)

2017-01-13

One of the key aspects to achieve high efficiency in ternary bulk-hetorojunction solar cells is the physical and chemical compatibility between the donor materials. Here, we report the synthesis of a novel conjugated polymer (P1) containing alternating pyridyl[2,1,3]thiadiazole between two different donor fragments, dithienosilole and indacenodithienothiophene (IDTT), used as a sensitizer in a host system of indacenodithieno[3,2-b]thiophene,2,3-bis(3-(octyloxy)phenyl)quinoxaline (PIDTTQ) and [6,6]-phenyl C{sub 70} butyric acid methyl ester (PC{sub 71}BM). We found that the use of the same IDTT unit in the host and guest materials does not lead to significant changes in the morphology of the ternary blend compared to the host binary. With the complementary use of optoelectronic characterizations, we found that the ternary cells suffer from a lower mobility-lifetime (μτ) product, adversely impacting the fill factor. However, the significant light harvesting in the near infrared region improvement, compensating the transport losses, results in an overall power conversion efficiency enhancement of ~7% for ternary blends as compared to the PIDTTQ:PC{sub 71}BM devices.

Description of light charged particle emission in ternary fission

International Nuclear Information System (INIS)

Andreev, A. V.; Adamian, G. G.; Antonenko, N. V.; Kuklin, S. N.; Scheid, W.

2010-01-01

We consider the motion of three fragments starting from the scission point of ternary system. In the alpha-accompanied ternary fission the initial conditions are not the free parameters and determined by minimization of potential energy at scission point. In the trajectory calculations the angular distribution and mean value of the kinetic energy of the alpha-particles are well described in the spontaneous ternary fission of 252 Cf. In the Be- and C-accompanied ternary fission we found that the emission of the third particle occurs from one of the heavy fragments after their separation. (authors)

Isobaric (vapour + liquid + liquid) equilibrium data for (di-n-propyl ether + n-propyl alcohol + water) and (diisopropyl ether + isopropyl alcohol + water) systems at 100 kPa

International Nuclear Information System (INIS)

Lladosa, Estela; Monton, Juan B.; Burguet, MaCruz; Torre, Javier de la

2008-01-01

Isobaric (vapour + liquid + liquid) equilibria were measured for the (di-n-propyl ether + n-propyl alcohol + water) and (diisopropyl ether + isopropyl alcohol + water) system at 100 kPa. The apparatus used for the determination of (vapour + liquid + liquid) equilibrium data was an all-glass dynamic recirculating still with an ultrasonic homogenizer couple to the boiling flask. The experimental data demonstrated the existence of a heterogeneous ternary azeotrope for both ternary systems. The (vapour + liquid + liquid) equilibria data were found to be thermodynamically consistent for both systems. The experimental data were compared with the estimation using UNIQUAC and NRTL models and the prediction of UNIFAC model

HCl removal using cycled carbide slag from calcium looping cycles

International Nuclear Information System (INIS)

Xie, Xin; Li, Yingjie; Wang, Wenjing; Shi, Lei

2014-01-01

Highlights: • Cycled carbide slag from calcium looping cycles is used to remove HCl. • The optimum temperature for HCl removal of cycled carbide slag is 700 °C. • The presence of CO 2 restrains HCl removal of cycled carbide slag. • CO 2 capture conditions have important effects on HCl removal of cycled carbide slag. • HCl removal capacity of carbide slag drops with cycle number rising from 1 to 50. - Abstract: The carbide slag is an industrial waste from chlor-alkali plants, which can be used to capture CO 2 in the calcium looping cycles, i.e. carbonation/calcination cycles. In this work, the cycled carbide slag from the calcium looping cycles for CO 2 capture was proposed to remove HCl in the flue gas from the biomass-fired and RDFs-fired boilers. The effects of chlorination temperature, HCl concentration, particle size, presence of CO 2 , presence of O 2 , cycle number and CO 2 capture conditions in calcium looping cycles on the HCl removal behavior of the carbide slag experienced carbonation/calcination cycles were investigated in a triple fixed-bed reactor. The chlorination product of the cycled carbide slag from the calcium looping after absorbing HCl is not CaCl 2 but CaClOH. The optimum temperature for HCl removal of the cycled carbide slag from the carbonation/calcination cycles is 700 °C. The chlorination conversion of the cycled carbide slag increases with increasing the HCl concentration. The cycled carbide slag with larger particle size exhibits a lower chlorination conversion. The presence of CO 2 decreases the chlorination conversions of the cycled carbide slag and the presence of O 2 has a trifling impact. The chlorination conversion of the carbide slag experienced 1 carbonation/calcination cycle is higher than that of the uncycled calcined sorbent. As the number of carbonation/calcination cycles increases from 1 to 50, the chlorination conversion of carbide slag drops gradually. The high calcination temperature and high CO 2

The feasibility of parameterizing four-state equilibria using relaxation dispersion measurements

International Nuclear Information System (INIS)

Li Pilong; Martins, Ilídio R. S.; Rosen, Michael K.

2011-01-01

Coupled equilibria play important roles in controlling information flow in biochemical systems, including allosteric molecules and multidomain proteins. In the simplest case, two equilibria are coupled to produce four interconverting states. In this study, we assessed the feasibility of determining the degree of coupling between two equilibria in a four-state system via relaxation dispersion measurements. A major bottleneck in this effort is the lack of efficient approaches to data analysis. To this end, we designed a strategy to efficiently evaluate the smoothness of the target function surface (TFS). Using this approach, we found that the TFS is very rough when fitting benchmark CPMG data to all adjustable variables of the four-state equilibria. After constraining a portion of the adjustable variables, which can often be achieved through independent biochemical manipulation of the system, the smoothness of TFS improves dramatically, although it is still insufficient to pinpoint the solution. The four-state equilibria can be finally solved with further incorporation of independent chemical shift information that is readily available. We also used Monte Carlo simulations to evaluate how well each adjustable parameter can be determined in a large kinetic and thermodynamic parameter space and how much improvement can be achieved in defining the parameters through additional measurements. The results show that in favorable conditions the combination of relaxation dispersion and biochemical manipulation allow the four-state equilibrium to be parameterized, and thus coupling strength between two processes to be determined.

Non-existence of Normal Tokamak Equilibria with Negative Central Current

International Nuclear Information System (INIS)

Hammett, G.W.; Jardin, S.C.; Stratton, B.C.

2003-01-01

Recent tokamak experiments employing off-axis, non-inductive current drive have found that a large central current hole can be produced. The current density is measured to be approximately zero in this region, though in principle there was sufficient current-drive power for the central current density to have gone significantly negative. Recent papers have used a large aspect-ratio expansion to show that normal MHD equilibria (with axisymmetric nested flux surfaces, non-singular fields, and monotonic peaked pressure profiles) can not exist with negative central current. We extend that proof here to arbitrary aspect ratio, using a variant of the virial theorem to derive a relatively simple integral constraint on the equilibrium. However, this constraint does not, by itself, exclude equilibria with non-nested flux surfaces, or equilibria with singular fields and/or hollow pressure profiles that may be spontaneously generated

Evaluation of ternary blended cements for use in transportation concrete structures

Science.gov (United States)

Gilliland, Amanda Louise

This thesis investigates the use of ternary blended cement concrete mixtures for transportation structures. The study documents technical properties of three concrete mixtures used in federally funded transportation projects in Utah, Kansas, and Michigan that used ternary blended cement concrete mixtures. Data were also collected from laboratory trial batches of ternary blended cement concrete mixtures with mixture designs similar to those of the field projects. The study presents the technical, economic, and environmental advantages of ternary blended cement mixtures. Different barriers of implementation for using ternary blended cement concrete mixtures in transportation projects are addressed. It was concluded that there are no technical, economic, or environmental barriers that exist when using most ternary blended cement concrete mixtures. The technical performance of the ternary blended concrete mixtures that were studied was always better than ordinary portland cement concrete mixtures. The ternary blended cements showed increased durability against chloride ion penetration, alkali silica reaction, and reaction to sulfates. These blends also had less linear shrinkage than ordinary portland cement concrete and met all strength requirements. The increased durability would likely reduce life cycle costs associated with concrete pavement and concrete bridge decks. The initial cost of ternary mixtures can be higher or lower than ordinary portland cement, depending on the supplementary cementitious materials used. Ternary blended cement concrete mixtures produce less carbon dioxide emissions than ordinary portland cement mixtures. This reduces the carbon footprint of construction projects. The barriers associated with implementing ternary blended cement concrete for transportation projects are not significant. Supplying fly ash returns any investment costs for the ready mix plant, including silos and other associated equipment. State specifications can make

Structures, equilibria and ligand exchange dynamics in the binary and ternary dioxouranium(VI)-ethylenediamine-N-N'-diacetic acid - fluoride system; a potentiometric, NMR and X-ray study

International Nuclear Information System (INIS)

Palladino, G.; Szabo, Z.; Fischer, A.; Grenthe, I.

2005-01-01

Full text of publication follows: The structure, thermodynamics and kinetics of the binary and ternary Uranyl(VI)- ethylenediamine- N-N'-di-acetate (in the following denoted EDDA) fluoride system have been studied using potentiometry, 1 H, 19 F NMR and a single-crystal X-ray determination. The potentiometric data were obtained using measurements of the free hydrogen ion and fluoride concentrations with glass and fluoride electrodes, respectively. The experimental data were used to deduce stoichiometry and equilibrium constants using a least square refinements programme. The UO 2 2+ - EDDA system could be studied up to -log[H 3 O + ] 3.4, after which a precipitate was formed. The test solutions contained two binary complexes, the uncharged UO 2 (EDDA)(aq) and UO 2 (H 3 EDDA) 3+ , with equilibrium constants log β(UO 2 EDDA) = 11.63 ± 0.02 and log β(UO 2 H 3 EDDA 3+ ) = 1.77 ± 0.04, respectively. By using fluoride as additional ligand the solubility increases because of the formation of very stable ternary complexes that allowed an experimental study over a larger pH range. The structure of the complexes in the ternary system was deduced using a combination of 1 H and 19 F NMR spectroscopy. The 19 F NMR spectra at lower pH, had peaks from the binary fluoride complexes (UO 2 F + , UO 2 F 2 (aq) and UO 2 F 3 - ) that could be used to obtain information on the equilibrium constants in the ternary system; at -log[H 3 O + ] > 4.7 new signals for the complexes (UO 2 ) 2 (EDDA) 2 F 2 2- , and UO 2 (EDDA)F - were observed. The analyses of 1 H NMR spectra indicate clearly that the EDDA ligand is chelate bonded in UO 2 (EDDA)F-. The fluorine exchange between UO 2 (EDDA)F- and UO 2 F 3 - was studied using 19 F NMR line-broadening technique. The experimental rate constant is k obs = k 0 + k 1 [UO 2 F 3 - ], with k 0 (3.24 ± 0.06) 10 2 s -1 and k 1 = (71.2 ± 2.3) 10 3 M -1 s -1 .The rate and the activation parameters for the exchange between UO 2 (EDDA)F - complex and free

Boron-carbide-aluminum and boron-carbide-reactive metal cermets. [B/sub 4/C-Al

Science.gov (United States)

Halverson, D.C.; Pyzik, A.J.; Aksay, I.A.

1985-05-06

Hard, tough, lighweight boron-carbide-reactive metal composites, particularly boron-carbide-aluminum composites, are produced. These composites have compositions with a plurality of phases. A method is provided, including the steps of wetting and reacting the starting materials, by which the microstructures in the resulting composites can be controllably selected. Starting compositions, reaction temperatures, reaction times, and reaction atmospheres are parameters for controlling the process and resulting compositions. The ceramic phases are homogeneously distributed in the metal phases and adhesive forces at ceramic-metal interfaces are maximized. An initial consolidated step is used to achieve fully dense composites. Microstructures of boron-carbide-aluminum cermets have been produced with modules of rupture exceeding 110 ksi and fracture toughness exceeding 12 ksi..sqrt..in. These composites and methods can be used to form a variety of structural elements.

Ternary particle yields in 249Cf(nth,f)

Science.gov (United States)

Tsekhanovich, I.; Büyükmumcu, Z.; Davi, M.; Denschlag, H. O.; Gönnenwein, F.; Boulyga, S. F.

2003-03-01

An experiment measuring ternary particle yields in 249Cf(nth,f) was carried out at the high flux reactor of the Institut Laue-Langevin using the Lohengrin recoil mass separator. Parameters of energy distributions were determined for 27 ternary particles up to 30Mg and their yields were calculated. The yields of 17 further ternary particles were estimated on the basis of the systematics developed. The heaviest particles observed in the experiment are 37Si and 37S; their possible origin is discussed.

The ternary system nickel-boron-silicon

International Nuclear Information System (INIS)

Lugscheider, E.; Reimann, H.; Knotek, O.

1975-01-01

The ternary system Nickel-Boron-Silicon was established at 850 0 C by means of X-ray diffraction, metallographic and micro-hardness examinations. The well known binary nickel borides and silicides resp. were confirmed. In the boron-silicon system two binary phases, SiBsub(4-x) with x approximately 0.7 and SiB 6 were found the latter in equilibrium with the β-rhombohedral boron. Confirming the two ternary silicon borides a greater homogeneity range was found for Ni 6 Si 2 B, the phase Nisub(4,6)Si 2 B published by Uraz and Rundqvist can better be described by the formula Nisub(4.29)Si 2 Bsub(1.43). In relation to further investigations we measured melting temperatures in ternary Ni-10 B-Si alloys by differential thermoanalysis. (author)

Design of ternary low-power Domino JKL flip—flop and its application

International Nuclear Information System (INIS)

Wang Pengjun; Yang Qiankun; Zheng Xuesong

2012-01-01

By researching the ternary flip—flop and the adiabatic Domino circuit, a novel design of low-power ternary Domino JKL flip—flop on the switch level is proposed. First, the switch-level structure of the ternary adiabatic Domino JKL flip—flop is derived according to the switch-signal theory and its truth table. Then the ternary loop operation circuit and ternary reverse loop operation circuit are achieved by employing the ternary JKL flip—flop. Finally, the circuit is simulated by using the Spice tool and the results show that the logic function is correct. The energy consumption of the ternary adiabatic Domino JKL flip—flop is 69% less than its conventional Domino counterpart. (semiconductor integrated circuits)

Intermediates and Generic Convergence to Equilibria

DEFF Research Database (Denmark)

Marcondes de Freitas, Michael; Wiuf, Carsten; Feliu, Elisenda

2017-01-01

Known graphical conditions for the generic and global convergence to equilibria of the dynamical system arising from a reaction network are shown to be invariant under the so-called successive removal of intermediates, a systematic procedure to simplify the network, making the graphical conditions...

Tungsten carbide encapsulated in nitrogen-doped carbon with iron/cobalt carbides electrocatalyst for oxygen reduction reaction

Energy Technology Data Exchange (ETDEWEB)

Zhang, Jie; Chen, Jinwei, E-mail: jwchen@scu.edu.cn; Jiang, Yiwu; Zhou, Feilong; Wang, Gang; Wang, Ruilin, E-mail: rl.wang@scu.edu.cn

2016-12-15

Graphical abstract: A hybrid catalyst was prepared via a quite green and simple method to achieve an one-pot synthesis of the N-doping carbon, tungsten carbides, and iron/cobalt carbides. It exhibited comparable electrocatalytic activity, higher durability and ability to methanol tolerance compared with commercial Pt/C to ORR. - Highlights: • A novel type of hybrid Fe/Co/WC@NC catalysts have been successfully synthesized. • The hybrid catalyst also exhibited better durability and methanol tolerance. • Multiple effective active sites of Fe{sub 3}C, Co{sub 3}C, WC, and NC help to improve catalytic performance. - Abstract: This work presents a type of hybrid catalyst prepared through an environmental and simple method, combining a pyrolysis of transition metal precursors, a nitrogen-containing material, and a tungsten source to achieve a one-pot synthesis of N-doping carbon, tungsten carbides, and iron/cobalt carbides (Fe/Co/WC@NC). The obtained Fe/Co/WC@NC consists of uniform Fe{sub 3}C and Co{sub 3}C nanoparticles encapsulated in graphitized carbon with surface nitrogen doping, closely wrapped around a plate-like tungsten carbide (WC) that functions as an efficient oxygen reduction reaction (ORR) catalyst. The introduction of WC is found to promote the ORR activity of Fe/Co-based carbide electrocatalysts, which is attributed to the synergistic catalysts of WC, Fe{sub 3}C, and Co{sub 3}C. Results suggest that the composite exhibits comparable electrocatalytic activity, higher durability, and ability for methanol tolerance compared with commercial Pt/C for ORR in alkaline electrolyte. These advantages make Fe/Co/WC@NC a promising ORR electrocatalyst and a cost-effective alternative to Pt/C for practical application as fuel cell.

Role of ternary fission in synthesis of bypassed nuclei

International Nuclear Information System (INIS)

Kramarovskij, Ya.M.; Chechev, V.P.

1983-01-01

A possible influence of ternary fission with escape of neutron-enriched light charged particles on the synthesis of bypassed nuclides is considered. It is shown that this concept cannot give explanation of bypassed isotope concentrations, but it can make some contribution, if the probability of ternary fission for superheavy nuclei grows sharply with Z 2 /A parameter. The account of β-delayed fission contributes to the shift of ternary fission fragments into the region of neutron-deficient isotopes. Consistent consideration of the ternary fission role in the nucleosynthesis is possible only with an important accumulation of experimental and theoretical data on this process, particularly for the nuclei with Z > 100

Preparation of aluminum nitride-silicon carbide nanocomposite powder by the nitridation of aluminum silicon carbide

NARCIS (Netherlands)

Itatani, K.; Tsukamoto, R.; Delsing, A.C.A.; Hintzen, H.T.J.M.; Okada, I.

2002-01-01

Aluminum nitride (AlN)-silicon carbide (SiC) nanocomposite powders were prepared by the nitridation of aluminum-silicon carbide (Al4SiC4) with the specific surface area of 15.5 m2·g-1. The powders nitrided at and above 1400°C for 3 h contained the 2H-phases which consisted of AlN-rich and SiC-rich

Ternary particle yields in 249Cf(nth,f)

International Nuclear Information System (INIS)

Tsekhanovich, I.; Bueyuekmumcu, Z.; Davi, M.; Denschlag, H.O.; Goennenwein, F.; Boulyga, S.F.

2003-01-01

An experiment measuring ternary particle yields in 249 Cf(n th ,f) was carried out at the high flux reactor of the Institut Laue-Langevin using the Lohengrin recoil mass separator. Parameters of energy distributions were determined for 27 ternary particles up to 30 Mg and their yields were calculated. The yields of 17 further ternary particles were estimated on the basis of the systematics developed. The heaviest particles observed in the experiment are 37 Si and 37 S; their possible origin is discussed

Data Requirements and Modeling for Gas Hydrate-Related Mixtures and a Comparison of Two Association Models

DEFF Research Database (Denmark)

Liang, Xiaodong; Aloupis, Georgios; Kontogeorgis, Georgios M.

2017-01-01

the performance of the CPA and sPC-SAFT EOS for modeling the fluid-phase equilibria of gas hydrate-related systems and will try to explore how the models can help in suggesting experimental measurements. These systems contain water, hydrocarbon (alkane or aromatic), and either methanol or monoethylene glycol...... parameter sets have been chosen for the sPC-SAFT EOS for a fair comparison. The comparisons are made for pure fluid properties, vapor liquid-equilibria, and liquid liquid equilibria of binary and ternary mixtures as well as vapor liquid liquid equilibria of quaternary mixtures. The results show, from...

Ballooning mode second stability region for sequences of tokamak equilibria

International Nuclear Information System (INIS)

Sugiyama, L.; Mark, J.W.K.

A numerical study of several sequences of tokamak equilibria derived from two flux conserving sequences confirms the tendency of high n ideal MHD ballooning modes to stabilize for values of the plasma beta greater than a second critical beta, for sufficiently favorable equilibria. The major stabilizing effect of increasing the inverse rotational transform profile q(Psi) for equilibria with the same flux surface geometry is shown. The unstable region shifts toward larger shear d ln q/d ln γ and the width of the region measured in terms of the poloidal beta or a pressure gradient parameter, for fixed shear, decreases. The smaller aspect ratio sequences are more sensitive to changes in q and have less stringent limits on the attainable value of the plasma beta in the high beta stable region. Finally, the disconnected mode approximation is shown to provide a reasonable description of the second high beta stability boundary

Gyrokinetic magnetohydrodynamics and the associated equilibria

Science.gov (United States)

Lee, W. W.; Hudson, S. R.; Ma, C. H.

2017-12-01

The gyrokinetic magnetohydrodynamic (MHD) equations, related to the recent paper by W. W. Lee ["Magnetohydrodynamics for collisionless plasmas from the gyrokinetic perspective," Phys. Plasmas 23, 070705 (2016)], and their associated equilibria properties are discussed. This set of equations consists of the time-dependent gyrokinetic vorticity equation, the gyrokinetic parallel Ohm's law, and the gyrokinetic Ampere's law as well as the equations of state, which are expressed in terms of the electrostatic potential, ϕ, and the vector potential, A , and support both spatially varying perpendicular and parallel pressure gradients and the associated currents. The corresponding gyrokinetic MHD equilibria can be reached when ϕ→0 and A becomes constant in time, which, in turn, gives ∇.(J∥+J⊥)=0 and the associated magnetic islands, if they exist. Examples of simple cylindrical geometry are given. These gyrokinetic MHD equations look quite different from the conventional MHD equations, and their comparisons will be an interesting topic in the future.

(Liquid + liquid) equilibria of perfluorocarbons with fluorinated ionic liquids

International Nuclear Information System (INIS)

Martinho, S.; Araújo, J.M.M.; Rebelo, L.P.N.; Pereiro, A.B.; Marrucho, I.M.

2013-01-01

Highlights: • (Liquid + liquid) equilibria perfluorocarbons and fluorinated ionic liquids. • Non-Random Two Liquid model was successfully applied. • Thermodynamic functions that describe the solvation process were calculated. -- Abstract: In order to evaluate the feasibility of partially replace perfluorocarbons (PFCs) with fluorinated ionic liquids (FILs) in PFCs-in-water emulsions, usually used for biomedical purposes, herein the (liquid + liquid) phase equilibria of FILs containing fluorinated chains longer than four carbons with PFCs were carried out in a wide range of temperatures. With this goal in mind, two PFCs (perfluorooctane and perfluorodecalin) were selected and the (liquid + liquid) equilibria of the binary mixtures of these PFCs and FILs were studied at atmospheric pressure in a temperature range from T (293.15 to 343.15) K. For these studies, FILs containing ammonium, pyridinium and imidazolium cations and different anions with fluorocarbon alkyl chains between 4 and 8 were included. Additionally, Non-Random Two Liquid (NRTL) thermodynamic model was successfully applied to correlate the behaviour of the PFCs + FILs binary mixtures. Moreover, thermodynamic functions that describe the solvation process were calculated from the experimental data

Three-dimensional studies of intergranular carbides in austenitic stainless steel.

Science.gov (United States)

Ochi, Minoru; Kawano, Rika; Maeda, Takuya; Sato, Yukio; Teranishi, Ryo; Hara, Toru; Kikuchi, Masao; Kaneko, Kenji

2017-04-01

A large number of morphological studies of intergranular carbides in steels have always been carried out in two dimensions without considering their dispersion manners. In this article, focused ion beam serial-sectioning tomography was carried out to study the correlation among the grain boundary characteristics, the morphologies and the dispersions of intergranular carbides in 347 austenitic stainless steel. More than hundred intergranular carbides were characterized in three dimensions and finally classified into three different types, two types of carbides probably semi-coherent to one of the neighboring grains with plate-type morphology, and one type of carbides incoherent to both grains with rod-type morphology. In addition, the rod-type carbide was found as the largest number of carbides among three types. Since large numbers of defects, such as misfit dislocations, may be present at the grain boundaries, which can be ideal nucleation sites for intergranular rod-type carbide precipitation. © The Author 2016. Published by Oxford University Press on behalf of The Japanese Society of Microscopy. All rights reserved.For permissions, please e-mail: journals.permissions@oup.com.

Ternary fission of 184466,476X formed in U + U collisions

International Nuclear Information System (INIS)

Karthikraj, C.; Subramanian, S.; Selvaraj, S.

2016-01-01

Recently, the very rare process of nuclear ternary fission has been of great interest in nuclear dynamics. Based on the statistical theory of fission, we discuss here the ternary-fission mass distribution of 184 466,476 X formed in low-energy U + U collisions for different heavy third fragments at T = 1 and 2 MeV. The expected ternary configurations 208 Pb + 208 Pb + 50 Ca and 204 Hg + 204 Hg + 58 Cr are obtained from the ternary fission of 184 466 X at T = 2 MeV. In addition, for both the systems, various possible ternary modes are listed for different heavy third fragments. Our results clearly indicate that the favored ternary configurations have either proton and/or neutron shell closure nucleus as one of their partners. (orig.)

Toroidal Extrap Equilibria

International Nuclear Information System (INIS)

Scheffel, J.

1982-04-01

Ideal MHD-equilibria for the toroidal EXTRAP configuration have been computed with an equilibrium code. The free-boundary prob- lem is solved by using the condition that the current density is proportional to r on a flux surface. It is found that the toroidal Z-pinch, initially induced in the central zero-field region of a transverse octupole field, drifts radially outwards producing an inverse -D shaped cross-section. The plasma current of this high- beta equilibrium may be increased if the plasma is pushed back by altering the external confining magnetic field as demonstrated. (Author)

Fusibility diagram of ternary system with incongruently melting double compound

International Nuclear Information System (INIS)

Lutsyk, V.I.; Vorob'eva, V.P.; Sumkina, O.G.

1989-01-01

Temperature calculation and properties of ternary eutectics and concentration coordinates of ternary peritectics accoriding to the linear model of initial crystallization surfaces as an element of the expert system for simulating fusibility diagrams of ternary systems is considered. It is shown that the calculated and experimental data on coordinates of ternary nonvariant points in the systems NaCl-PbCl 2 -CdCl 2 , PbCl 2 -CaCl 2 -UCl 4 , CaF 2 -NaF-CsF and UCl 3 -CaCl 2 -ThCl 4 are in good agreement

Crystallization features of ternary reversible reciprocal systems

International Nuclear Information System (INIS)

Tomashik, V.N.; Shcherbak, L.P.; Fejchuk, P.I.; Grytsiv, V.I.

2006-01-01

Some features of the primary crystallization of phases in ternary reversible reciprocal system are considered and discussed. The diagonal join CdTe-GeSe of the CdTe + GeSe = CdSe + GeTe ternary reciprocal system is studied to show that the features in primary and secondary heating and cooling curves in such systems under fully equilibrium conditions are not reproduced upon consecutive heating and cooling sessions, because of the existence of different amounts of the reagents and the reaction products in the mixture; the temperatures of each transformation lie in a range. Those who experimentally investigate other ternary and more complex reversible reciprocal systems should take this fact into account [ru

Graphite and boron carbide composites made by hot-pressing

International Nuclear Information System (INIS)

Miyazaki, K.; Hagio, T.; Kobayashi, K.

1981-01-01

Composites consisting of graphite and boron carbide were made by hot-pressing mixed powders of coke carbon and boron carbide. The change of relative density, mechanical strength and electrical resistivity of the composites and the X-ray parameters of coke carbon were investigated with increase of boron carbide content and hot-pressing temperature. From these experiments, it was found that boron carbide powder has a remarkable effect on sintering and graphitization of coke carbon powder above the hot-pressing temperature of 2000 0 C. At 2200 0 C, electrical resistivity of the composite and d(002) spacing of coke carbon once showed minimum values at about 5 to 10 wt% boron carbide and then increased. The strength of the composite increased with increase of boron carbide content. It was considered that some boron from boron carbide began to diffuse substitutionally into the graphite structure above 2000 0 C and densification and graphitization were promoted with the diffusion of boron. Improvements could be made to the mechanical strength, density, oxidation resistance and manufacturing methods by comparing with the properties and processes of conventional graphites. (author)

Stability of the n = 1 internal kink mode in equilibria with flows

International Nuclear Information System (INIS)

Aydemir, A.Y.; Waelbroeck, F.L.

1996-01-01

Stabilizing influence of mass flows, either directly or through their shearing action, on various modes is now generally recognized. Here we examine linear and nonlinear stability of the n = 1 internal kink mode in equilibria with toroidal rotation, using our nonlinear, initial-value MHD code CTD, which can be used to generate self-consistent equilibria with flows in arbitrary geometries. It is well known that equilibrium mass flows introduce complications in determination of MHD equilibria and their stability properties, such as the loss of self-adjointness and an increase in the number of conditions required to uniquely determine the equilibria. Thus, even with purely toroidal flows, an implicit statement about the equation of state is needed, in addition to a knowledge of the magnetic field and velocity profiles; rotation in an adiabatic plasma leads to a different equilibrium than, for example, in an isothermal one, with possibly quite different stability properties. We find that the expected stabilizing influence of toroidal rotation on n = 1 is generally absent in adiabatically generated equilibria in which, of all the relevant thermodynamic variables, only the specific entropy is a flux function, s = s (ψ). Fortunately, physically more relevant isothermal case where the temperature is constant on flux surfaces, T = T(ψ), has more favorable stability characteristics. On the other hand, an inconsistent but common practice of ignoring density perturbations, a benign omission for static equilibria, leads to overly optimistic results when equilibrium flows axe present, predicting stability when there may not be any. The crucial role played by the equation of state in determining equilibrium raises questions regarding the role of parallel transport in stability calculations; this and other nonideal effects, along with the role of plasma β vs. the rotational β, and nonlinear stability when the mode is pushed beyond marginality, will be discussed

Structural studies of the phase separation in the UO2–PuO2–Pu2O3 ternary system

International Nuclear Information System (INIS)

Truphémus, Thibaut; Belin, Renaud C.; Richaud, Jean-Christophe; Reynaud, Muriel; Martinez, Marie-Annick; Félines, Isabelle; Arredondo, Antoine; Miard, Audrey; Dubois, Thierry; Adenot, Frédéric; Rogez, Jacques

2013-01-01

In the oxygen hypo-stoichiometric range of (U 1−y Pu y )O 2−x mixed oxide MOX fuels, the U–Pu–O phase diagram is known to exhibit a large biphasic domain depending on the Pu content. However, the phase equilibria are still to be fully described as various representations are proposed in the literature. In the present work, we notify new insights into the phase separation occurring in the UO 2 –PuO 2 –Pu 2 O 3 domain at room temperature. Our microstructural and X-ray diffraction results are compared to the different representations reported in the literature. We provide, for the first time in the hypo-stoichiometric domain, an indisputable experimental observation of a triphasic region at high Pu content, composed of two fluorite-type structures and of one α-Pu 2 O 3 sesquioxyde type structure. These results are in contradiction with previous experimental representations of the U–Pu–O ternary system.

Multiple equilibria in a simple elastocapillary system

KAUST Repository

Taroni, Michele; Vella, Dominic

2012-01-01

properties two stable equilibria may exist, and show via numerical solutions of the dynamic model that it is the initial state of the system that determines which stable equilibrium is ultimately reached. © 2012 Cambridge University Press.

Joining of boron carbide using nickel interlayer

International Nuclear Information System (INIS)

Vosughi, A.; Hadian, A. M.

2008-01-01

Carbide ceramics such as boron carbide due to their unique properties such as low density, high refractoriness, and high strength to weight ratio have many applications in different industries. This study focuses on direct bonding of boron carbide for high temperature applications using nickel interlayer. The process variables such as bonding time, temperature, and pressure have been investigated. The microstructure of the joint area was studied using electron scanning microscope technique. At all the bonding temperatures ranging from 1150 to 1300 d eg C a reaction layer formed across the ceramic/metal interface. The thickness of the reaction layer increased by increasing temperature. The strength of the bonded samples was measured using shear testing method. The highest strength value obtained was about 100 MPa and belonged to the samples bonded at 1250 for 75 min bonding time. The strength of the joints decreased by increasing the bonding temperature above 1250 d eg C . The results of this study showed that direct bonding technique along with nickel interlayer can be successfully utilized for bonding boron carbide ceramic to itself. This method may be used for bonding boron carbide to metals as well.

Surface metallurgy of cemented carbide tools

International Nuclear Information System (INIS)

Chopra, K.L.; Kashyap, S.C.; Rao, T.V.; Rajagopalan, S.; Srivastava, P.K.

1983-01-01

Transition metal carbides, owing to their high melting point, hardness and wear resistance, are potential candidates for specific application in rockets, nuclear engineering equipment and cutting tools. Tungsten carbide sintered with a binder (either cobalt metal or a mixture of Co + TiC and/or TaC(NbC)) is used for cutting tools. The surface metallurgy of several commercially available cemented carbide tools was studied by Auger electron spectroscopy and X-ray photoelectron spectroscopy techniques. The tool surfaces were contaminated by adsorbed oxygen up to a depth of nearly 0.3 μm causing deterioration of the mechanical properties of the tools. Studies of fractured samples indicated that the tool surfaces were prone to oxygen adsorption. The fracture path passes through the cobalt-rich regions. The ineffectiveness of a worn cutting tool is attributed to the presence of excessive iron from the steel workpiece and carbon and oxygen in the surface layers of the tool. The use of appropriate hard coatings on cemented carbide tools is suggested. (Auth.)

How hard is it to find extreme Nash equilibria in network congestion games?

NARCIS (Netherlands)

Gassner, E.; Hatzl, J.; Krumke, S.O.; Sperber, H.; Woeginger, G.J.; Papadimitriou, C.; Zhang, S.

2008-01-01

We study the complexity of finding extreme pure Nash equilibria in symmetric (unweighted) network congestion games. In our context best and worst equilibria are those with minimum respectively maximum makespan. On series-parallel graphs a worst Nash equilibrium can be found by a Greedy approach

A high-speed interconnect network using ternary logic

DEFF Research Database (Denmark)

Madsen, Jens Kargaard; Long, S. I.

1995-01-01

This paper describes the design and implementation of a high-speed interconnect network (ICN) for a multiprocessor system using ternary logic. By using ternary logic and a fast point-to-point communication technique called STARI (Self-Timed At Receiver's Input), the communication between...

Hydrostatic Equilibria of Rotating Stars with Realistic Equation of State

Science.gov (United States)

Yasutake, Nobutoshi; Fujisawa, Kotaro; Okawa, Hirotada; Yamada, Shoichi

Stars rotate generally, but it is a non-trivial issue to obtain hydrostatic equilibria for rapidly rotating stars theoretically, especially for baroclinic cases, in which the pressure depends not only on the density, but also on the temperature and compositions. It is clear that the stellar structures with realistic equation of state are the baroclinic cases, but there are not so many studies for such equilibria. In this study, we propose two methods to obtain hydrostatic equilibria considering rotation and baroclinicity, namely the weak-solution method and the strong-solution method. The former method is based on the variational principle, which is also applied to the calculation of the inhomogeneous phases, known as the pasta structures, in crust of neutron stars. We found this method might break the balance equation locally, then introduce the strong-solution method. Note that our method is formulated in the mass coordinate, and it is hence appropriated for the stellar evolution calculations.

Friction and wear performance of diamond-like carbon, boron carbide, and titanium carbide coatings against glass

International Nuclear Information System (INIS)

Daniels, B.K.; Brown, D.W.; Kimock, F.M.

1997-01-01

Protection of glass substrates by direct ion beam deposited diamond-like carbon (DLC) coatings was observed using a commercial pin-on-disk instrument at ambient conditions without lubrication. Ion beam sputter-deposited titanium carbide and boron carbide coatings reduced sliding friction, and provided tribological protection of silicon substrates, but the improvement factor was less than that found for DLC. Observations of unlubricated sliding of hemispherical glass pins at ambient conditions on uncoated glass and silicon substrates, and ion beam deposited coatings showed decreased wear in the order: uncoated glass>uncoated silicon>boron carbide>titanium carbide>DLC>uncoated sapphire. Failure mechanisms varied widely and are discussed. Generally, the amount of wear decreased as the sliding friction decreased, with the exception of uncoated sapphire substrates, for which the wear was low despite very high friction. There is clear evidence that DLC coatings continue to protect the underlying substrate long after the damage first penetrates through the coating. The test results correlate with field use data on commercial products which have shown that the DLC coatings provide substantial extension of the useful lifetime of glass and other substrates. copyright 1997 Materials Research Society

Characterization of carbon, nitrogen, oxygen and refractory metals in binary and ternary silicon-based films using ion beam methods

International Nuclear Information System (INIS)

Somatri-Bouamrane, R.

1996-01-01

Ion beam methods (non Rutherford backscattering, nuclear reactions) have been carried out in order to characterize silicon-based films. The cross sections for the reactions 12 C(α,α), 14 N(α,α), 16 O(α,α), 28 Si(α,α) and 14 N(α,p) have been measured within 2 and 7 MeV. CVD beta SiC films could be analyzed and the interface between silicon carbide and the (100) silicon substrate was studied. The epitaxial growth of the beta SiC film could be modelled by comparing the results obtained with ion beam analysis, infrared spectroscopy and electron microscopy. Moreover, the stoichiometry of low pressure CVD Me-Si-N (Me=Re, W, Ti, Ta) ternary systems was studied. The evolution of the nitrogen content in W-Si-N systems allowed to study their stability with respect to the annealing conditions. (N.T.)

Tribology of carbide derived carbon films synthesized on tungsten carbide

Science.gov (United States)

Tlustochowicz, Marcin

Tribologically advantageous films of carbide derived carbon (CDC) have been successfully synthesized on binderless tungsten carbide manufactured using the plasma pressure compaction (P2CRTM) technology. In order to produce the CDC films, tungsten carbide samples were reacted with chlorine containing gas mixtures at temperatures ranging from 800°C to 1000°C in a sealed tube furnace. Some of the treated samples were later dechlorinated by an 800°C hydrogenation treatment. Detailed mechanical and structural characterizations of the CDC films and sliding contact surfaces were done using a series of analytical techniques and their results were correlated with the friction and wear behavior of the CDC films in various tribosystems, including CDC-steel, CDC-WC, CDC-Si3N4 and CDC-CDC. Optimum synthesis and treatment conditions were determined for use in two specific environments: moderately humid air and dry nitrogen. It was found that CDC films first synthesized at 1000°C and then hydrogen post-treated at 800°C performed best in air with friction coefficient values as low as 0.11. However, for dry nitrogen applications, no dechlorination was necessary and both hydrogenated and as-synthesized CDC films exhibited friction coefficients of approximately 0.03. A model of tribological behavior of CDC has been proposed that takes into consideration the tribo-oxidation of counterface material, the capillary forces from adsorbed water vapor, the carbon-based tribofilm formation, and the lubrication effect of both chlorine and hydrogen.

Natural precursor based hydrothermal synthesis of sodium carbide for reactor applications

Science.gov (United States)

Swapna, M. S.; Saritha Devi, H. V.; Sebastian, Riya; Ambadas, G.; Sankararaman, S.

2017-12-01

Carbides are a class of materials with high mechanical strength and refractory nature which finds a wide range of applications in industries and nuclear reactors. The existing synthesis methods of all types of carbides have problems in terms of use of toxic chemical precursors, high-cost, etc. Sodium carbide (Na2C2) which is an alkali metal carbide is the least explored one and also that there is no report of low-cost and low-temperature synthesis of sodium carbide using the eco-friendly, easily available natural precursors. In the present work, we report a simple low-cost, non-toxic hydrothermal synthesis of refractory sodium carbide using the natural precursor—Pandanus. The formation of sodium carbide along with boron carbide is evidenced by the structural and morphological characterizations. The sample thus synthesized is subjected to field emission scanning electron microscopy (FESEM), x-ray powder diffraction (XRD), ultraviolet (UV)—visible spectroscopy, Fourier transform infrared spectroscopy (FTIR), Raman, and photoluminescent (PL) spectroscopic techniques.

Vanadium carbide coatings: deposition process and properties

International Nuclear Information System (INIS)

Borisova, A.; Borisov, Y.; Shavlovsky, E.; Mits, I.; Castermans, L.; Jongbloed, R.

2001-01-01

Vanadium carbide coatings on carbon and alloyed steels were produced by the method of diffusion saturation from the borax melt. Thickness of the vanadium carbide layer was 5-15 μm, depending upon the steel grade and diffusion saturation parameters. Microhardness was 20000-28000 MPa and wear resistance of the coatings under conditions of end face friction without lubrication against a mating body of WC-2Co was 15-20 times as high as that of boride coatings. Vanadium carbide coatings can operate in air at a temperature of up to 400 o C. They improve fatigue strength of carbon steels and decrease the rate of corrosion in sea and fresh water and in acid solutions. The use of vanadium carbide coatings for hardening of various types of tools, including cutting tools, allows their service life to be extended by a factor of 3 to 30. (author)

Phase equilibria of carbohydrates in polar solvents

DEFF Research Database (Denmark)

Jonsdottir, Svava Osk; Rasmussen, Peter

1999-01-01

A method for calculating interaction energies and interaction parameters with molecular mechanics methods is extended to predict solid-liquid equilibria (SLE) for saccharides in aqueous solution, giving results in excellent agreement with experimental values. Previously, the method has been shown...

Reactor irradiation effect on the physical-mechanical properties of zirconium carbides and niobium carbides

International Nuclear Information System (INIS)

Andrievskij, R.A.; Vlasov, K.P.; Shevchenko, A.S.; Lanin, A.G.; Pritchin, S.A.; Klyushin, V.V.; Kurushin, S.P.; Maskaev, A.S.

1978-01-01

A study has been made of the effect of the reactor radiation by a flux of neutrons 1.5x10 20 n/cm 2 (E>=1 meV) at radiation temperatures of 150 and 1100 deg C on the physico-mechanical properties of carbides of zirconium and niobium and their equimolar hard solution. A difference has been discovered in the behaviour of the indicated carbides under the effect of radiation. Under the investigated conditions of radiation the density of zirconium carbide is being decreased, while in the niobium carbide no actual volumetric changes occur. The increase of the lattice period in ZrC is more significant than in NbC. The electric resistance of ZrC is also changed more significantly than in the case of NbC, while for the microhardness a reverse relationship is observed. Strength and elasticity modulus change insignificantly in both cases. Resistance to crack formation shows a higher reduction for ZrC than for NbC, while the thermal strength shows an approximately similar increase. The equimolar hard solution of ZrC and NbC behaves to great extent similar to ZrC, although the change in electric resistance reminds of NbC while thermal strength changes differently. The study of the microstructure of the specimens has shown that radiation causes a large number of etching patterns-dislocations in NbC which are almost absent in ZrC

Kinetic study of lithium-cadmium ternary amalgam decomposition

International Nuclear Information System (INIS)

Cordova, M.H.; Andrade, C.E.

1992-01-01

The effect of metals, which form stable lithium phase in binary alloys, on the formation of intermetallic species in ternary amalgams and their effect on thermal decomposition in contact with water is analyzed. Cd is selected as ternary metal, based on general experimental selection criteria. Cd (Hg) binary amalgams are prepared by direct contact Cd-Hg, whereas Li is formed by electrolysis of Li OH aq using a liquid Cd (Hg) cathodic well. The decomposition kinetic of Li C(Hg) in contact with 0.6 M Li OH is studied in function of ageing and temperature, and these results are compared with the binary amalgam Li (Hg) decomposition. The decomposition rate is constant during one hour for binary and ternary systems. Ageing does not affect the binary systems but increases the decomposition activation energy of ternary systems. A reaction mechanism that considers an intermetallic specie participating in the activated complex is proposed and a kinetic law is suggested. (author)

Joining of porous silicon carbide bodies

Science.gov (United States)

Bates, Carl H.; Couhig, John T.; Pelletier, Paul J.

1990-05-01

A method of joining two porous bodies of silicon carbide is disclosed. It entails utilizing an aqueous slip of a similar silicon carbide as was used to form the porous bodies, including the sintering aids, and a binder to initially join the porous bodies together. Then the composite structure is subjected to cold isostatic pressing to form a joint having good handling strength. Then the composite structure is subjected to pressureless sintering to form the final strong bond. Optionally, after the sintering the structure is subjected to hot isostatic pressing to further improve the joint and densify the structure. The result is a composite structure in which the joint is almost indistinguishable from the silicon carbide pieces which it joins.

Conceptual design study of LMFBR core with carbide fuel

International Nuclear Information System (INIS)

Tezuka, H.; Hojuyama, T.; Osada, H.; Ishii, T.; Hattori, S.; Nishimura, T.

1987-01-01

Carbide fuel is a hopeful candidate for demonstration FBR(DFBR) fuel from the plant cost reduction point of view. High thermal conductivity and high heavy metal content of carbide fuel lead to high linear heat rate and high breeding ratio. We have analyzed carbide fuel core characteristics and have clarified the concept of carbide fuel core. By survey calculation, we have obtained a correlation map between core parameters and core characteristics. From the map, we have selected a high efficiency core whose features are better than those of an oxide core, and have obtained reactivity coefficients. The core volume and the reactor fuel inventory are approximately 20% smaller, and the burn-up reactivity loss is 50% smaller compared with the oxide fuel core. These results will reduce the capital cost. The core reactivity coefficients are similar to the conventional oxide DFBR's. Therefore the carbide fuel core is regarded as safe as the oxide core. Except neutron fluence, the carbide fuel core has better nuclear features than the oxide core

Some axisymmetric equilibria for certain ideal and resistive magnetohydrodynamics with incompressible flows

Directory of Open Access Journals (Sweden)

S.M. Moawad

Full Text Available In this paper, the equilibrium properties of some ideal and resistive magnetohydrodynamics (MHD are investigated. The governing equations are taken in the steady state for parallel and non-parallel flow to magnetic filed. The governing equations are reduced to Bernoulli-Grad-Shafranov system. The problem of finding exact equilibria to the governing equations in the presence of incompressible mass flows is studied. Several nonlinear equilibria of the governing equations are obtained with aid of constructed constraints. The obtained results cover several previously configurations and include new considerations about the nonlinearity of magnetic flux stream variables. The possibility of applying the obtained results to magnetic confinement devices are discussed. Keywords: Magnetohydrodynamics, Axisymmetric plasma, Resistivity, Incompressible flows, Exact equilibria, Magnetic confinement devices

Microstructural studies of carbides in MAR-M247 nickel-based superalloy

Science.gov (United States)

Szczotok, A.; Rodak, K.

2012-05-01

Carbides play an important role in the strengthening of microstructures of nickel-based superalloys. Grain boundary carbides prevent or retard grain-boundary sliding and make the grain boundary stronger. Carbides can also tie up certain elements that would otherwise promote phase instability during service. Various types of carbides are possible in the microstructure of nickel-based superalloys, depending on the superalloy composition and processing. In this paper, scanning electron and scanning transmission electron microscopy studies of carbides occurring in the microstructure of polycrystalline MAR-M247 nickel-based superalloy were carried out. In the present work, MC and M23C6 carbides in the MAR-M247 microstructure were examined.

Resurrecting Equilibria Through Cycles

DEFF Research Database (Denmark)

Barnett, Richard C.; Bhattacharya, Joydeep; Bunzel, Helle

equilibria because they asymptotically violate some economic restriction of the model. The literature has always ruled out such paths. This paper studies a pure-exchange monetary overlapping generations economy in which real balances cycle forever between momentary equilibrium points. The novelty is to show...... that segments of the offer curve that have been previously ignored, can in fact be used to produce asymptotically valid cyclical paths. Indeed, a cycle can bestow dynamic validity on momentary equilibrium points that had erstwhile been classified as dynamically invalid....

The phase equilibria and thermal stability of the long-period stacking ordered phase in the Mg–Cu–Y system

International Nuclear Information System (INIS)

Jiang, Min; Su, Xiulan; Li, Hongxiao; Ren, Yuping; Qin, Gaowu

2014-01-01

Highlights: • 14H LPSO structure has been confirmed to be stable in the Mg–Cu–Y system. • Partial isothermal sections of the Mg–Cu–Y system from 300 to 450 °C have been established. • Reaction L + α-Mg ↔ 14H + Mg 2 Cu has been determined in the Mg–Cu–Y system. • The thermal stability of the 14H phase in the Mg–Cu–Y system has been well studied. - Abstract: Phase equilibria in the Mg-rich Mg–Cu–Y system at 300, 400 and 450 °C have been experimentally investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), differential scanning calorimetry (DSC), electron probe micro-analyzer (EPMA) and transmission electron microscope (TEM). The results show that a long-period stacking ordered (LPSO) phase 14H is stable in the Mg–Cu–Y system, which is the only one ternary intermetallic compound that gets a thermodynamic equilibrium with the a-Mg phase. The equilibrium 14H phase has a very limited solid solution range, and can be nearly regarded as a ternary stoichiometric compound with a formulae as Mg 91 Cu 4 Y 5 . The thermal stability of the 14H phase in the Mg–Cu–Y system has been well studied, which shows that the 14H phase disappears varying from 442 °C to 490 °C depending on the alloy composition. The isothermal sections of the Mg-rich Mg–Cu–Y system at 300, 400 and 450 °C have been finally established, and moreover, a quasi-peritectic reaction L + α-Mg ↔ 14H + Mg 2 Cu has been determined occurring at 442 °C with an estimated liquid composition of Mg 77 Cu 18 Y 5

(Liquid + liquid) equilibria measurements for ternary systems (sulfolane + a carboxylic acid + n-heptane) at T = 303.15 K and at 0.1 MPa

International Nuclear Information System (INIS)

Cele, N.P.; Bahadur, I.; Redhi, G.G.; Ebenso, E.E.

2016-01-01

Highlights: • The (liquid + liquid) equilibrium for (sulfolane + a carboxylic acid + heptane) was measured. • Selectivity values for solvent separation efficiency were calculated. • Separation of carboxylic acids from heptane is feasible by extraction. • Three parameter equations have been fitted to the binodal curve data. • The NRTL and UNIQUAC models were used to correlate the experimental data. - Abstract: In the present work, new (liquid + liquid) equilibrium (LLE) values are reported for ternary systems {sulfolane(1) + acetic acid, or propanoic acid, or butanoic acid, or 2-methylpropanoic acid, or pentanoic acid, or 3-methylbutanoic acid (2) + n-heptane (3)} at T = 303.15 K and at p = 0.1 MPa. The mutual solubility of carboxylic acid in sulfolane is dependent on the length and structure of the alkyl chain of the carboxylic acid; it progressively increases with an increase in the alkyl chain of the carboxylic acid. The single phase homogenous region increases as the alkyl chain of the carboxylic acid increases. The n-heptane is most soluble in the carboxylic acid mixtures with long alkyl chain, that is, (3-methylbutanoic acid + sulfolane) and (pentanoic acid + sulfolane) systems and least soluble in the carboxylic acid with short alkyl chain (acetic acid + sulfolane) system. Carboxylic acid together with many other oxygenates and hydrocarbons are produced by SASOL Company in South Africa using the Fischer–Tropsch process. The details about this process are given in introduction section. The NRTL and UNIQUAC models were used to correlate the experimental tie-lines and to calculate the phase compositions of the ternary systems. It was found that the NRTL model fits the experimental values significantly better than the UNIQUAC model.

Fabrication of chamfered uranium-plutonium mixed carbide pellets

International Nuclear Information System (INIS)

Arai, Yasuo; Iwai, Takashi; Shiozawa, Kenichi; Handa, Muneo

1985-10-01

Chamfered uranium-plutonium mixed carbide pellets for high burnup irradiation test in JMTR were fabricated in glove boxes with purified argon gas. The size of die and punch in a press was decided from pellet densities and dimensions including the angle of chamfered parts. No chip or crack caused by adopting chamfered pellets was found in both pressing and sintering stages. In addition to mixed carbide pellets, uranium carbide pellets used as insulators were also successfully fabricated. (author)

Carbides in Nodular Cast Iron with Cr and Mo

Directory of Open Access Journals (Sweden)

S. Pietrowski

2007-07-01

Full Text Available In these paper results of elements microsegregation in carbidic nodular cast iron have been presented. A cooling rate in the centre of the cross-section and on the surface of casting and change of moulding sand temperature during casting crystallization and its self-cooling have been investigated. TDA curves have been registered. The linear distribution of elements concentration in an eutectic grain, primary and secondary carbides have been made. It was found, that there are two kinds of carbides: Cr and Mo enriched. A probable composition of primary and secondary carbides have been presented.

Sloshing-ion equilibria in the TARA endplugs

International Nuclear Information System (INIS)

Hokin, S.; Kesner, J.

1983-11-01

We have employed a modified version of the LLNL Bounce-average Fokker-Planck code to model neutral beam-produced sloshing-ion equilibria in the TARA endplugs. The questions we have addressed concern the effect of deuterium beam operation as opposed to hydrogen operation, and the advantage of using full-energy beams rather than the usual three-component beams. We find that, for the expected base case TARA operating parameters, a 40% savings in required beam power is attained by using deuterium beams rather than hydrogen beams, and that the use of full-energy beams results in an additional 26% power savings for these parameters. For higher plasma temperatures the use of full-energy beams becomes significantly advantagous. We have also investigated the equilibria of two possible alternate mirror configurations for the TARA endplugs, believed to be more stable to trapped particle modes, and report those results here

Sequential character of low-energy ternary and quaternary nuclear fission

Energy Technology Data Exchange (ETDEWEB)

Kadmensky, S. G., E-mail: kadmensky@phys.vsu.ru; Bulychev, A. O. [Voronezh State University (Russian Federation)

2016-09-15

An analysis of low-energy true ternary (quaternary) nuclear fission leads to the conclusion that these fission modes have a sequential two-step (three-step) character such that the emission of a third particle (third and fourth particles) and the separation of fission fragments occur at distinctly different instants, in contrast to the simultaneous emergence of all fission products in the case of onestep ternary (quaternary) fission. This conclusion relies on the following arguments. First, the emission of a third particle (third and fourth particles) from a fissile nucleus is due to a nonevaporative mechanism associated with a nonadiabatic character of the collective deformation motion of this nucleus at the stages preceding its scission. Second, the axial symmetry of the deformed fissile compound nucleus and the direction of its symmetry axis both remain unchanged at all stages of ternary (quaternary) fission. This circumstancemakes it possible to explain themechanism of the appearance of observed anisotropies and T — odd asymmeries in the angular distributions of products of ternary (quaternary) nuclear fission. Third, the T —odd asymmetry discovered experimentally in ternary nuclear fission induced by cold polarized neutrons obeys the T —invariance condition only in the case of a sequential two-step (three-step) character of true ternary (quaternary) nuclear fission. At the same time, this asymmetry is not a T —invariant quantity in the case of the simultaneous emission of products of true ternary (quaternary) nuclear fission from the fissile compound nucleus.

Sequential character of low-energy ternary and quaternary nuclear fission

International Nuclear Information System (INIS)

Kadmensky, S. G.; Bulychev, A. O.

2016-01-01

An analysis of low-energy true ternary (quaternary) nuclear fission leads to the conclusion that these fission modes have a sequential two-step (three-step) character such that the emission of a third particle (third and fourth particles) and the separation of fission fragments occur at distinctly different instants, in contrast to the simultaneous emergence of all fission products in the case of onestep ternary (quaternary) fission. This conclusion relies on the following arguments. First, the emission of a third particle (third and fourth particles) from a fissile nucleus is due to a nonevaporative mechanism associated with a nonadiabatic character of the collective deformation motion of this nucleus at the stages preceding its scission. Second, the axial symmetry of the deformed fissile compound nucleus and the direction of its symmetry axis both remain unchanged at all stages of ternary (quaternary) fission. This circumstancemakes it possible to explain themechanism of the appearance of observed anisotropies and T — odd asymmeries in the angular distributions of products of ternary (quaternary) nuclear fission. Third, the T —odd asymmetry discovered experimentally in ternary nuclear fission induced by cold polarized neutrons obeys the T —invariance condition only in the case of a sequential two-step (three-step) character of true ternary (quaternary) nuclear fission. At the same time, this asymmetry is not a T —invariant quantity in the case of the simultaneous emission of products of true ternary (quaternary) nuclear fission from the fissile compound nucleus.

Interfacial reactions in intermetallic matrix composites

International Nuclear Information System (INIS)

Cantrell, L.B.; Clevenger, E.M.; Perepezko, J.H.

1993-01-01

The thermal stability of advanced composites is dominated by the behavior of internal interfaces. Analysis of these internal interfaces often involves consideration of at least ternary order phase equilibria. Limited thermodynamic data exists for ternary and higher order systems. However, a combined approach based upon the use of binary data to estimate ternary phase equilibria and experimentally determined reaction pathways is effective in the analysis of interface reactions in composite systems. In blended powder samples, thermal analysis was used to find possible reaction temperatures, while X-ray analysis, EDS, and EPMA of diffusion couples were used to assess interdiffusion reaction pathways. The approach is illustrated by compatibility studies between TiAl and TiSi 2 at 1,100 C, and in-situ reactions between B 4 C and TiAl at 1300 C where multiple reaction sequences have been analyzed to provide guidance for the design of in-situ reaction processing of composites

Determination of free carbon content in boron carbide ceramic powders

International Nuclear Information System (INIS)

Castro, A.R.M. de; Lima, N.B. de; Paschoal, J.O.A.

1990-01-01

Boron carbide is a ceramic material of technological importance due to its hardness and high chemical and thermal stabilities. Free carbon is always found as a process dependent impurity in boron carbide. The development of procedures for its detection is required because its presence leads to a degradation of the boron carbide properties. In this work, several procedures for determining free carbon content in boron carbide specimens are reported and discussed for comparison purposes. (author) [pt

Re-analysis of exponential rigid-rotor astron equilibria

International Nuclear Information System (INIS)

Lovelace, R.V.; Larrabee, D.A.; Fleischmann, H.H.

1978-01-01

Previous studies of exponential rigid-rotor astron equilibria include particles which are not trapped in the self-field of the configuration. The modification of these studies required to exclude untrapped particles is derived

Equilibrator: Modeling Chemical Equilibria with Excel

Science.gov (United States)

Vander Griend, Douglas A.

2011-01-01

Equilibrator is a Microsoft Excel program for learning about chemical equilibria through modeling, similar in function to EQS4WIN, which is no longer supported and does not work well with newer Windows operating systems. Similar to EQS4WIN, Equilibrator allows the user to define a system with temperature, initial moles, and then either total…

Nash equilibria via duality and homological selection

Indian Academy of Sciences (India)

1Quantitative Methods and Information Systems Area, Indian Institute ... The original proof of existence of Nash equilibria [13] uses fairly ...... The fiber over a regular point a of the disk Di consists of three inverse images (labeled. A1,A2,A3 in ...

Zr-Fe-Sn Ternary System Phase Diagrams- New Experimental Results

International Nuclear Information System (INIS)

Nieva, N; Gomez, A; Arias, D

2004-01-01

New experimental results for the Zr-Fe-Sn ternary system are presented in this paper. The phases present and equilibrium relations for the 900 o C isothermal on the central zone of the Gibbs triangle are analysed. A set of ternary alloys was designed and obtained, and they were analysed by semi quantitative SEM- EDS, XRD, and metallographic samples. The resulting ternary phase diagrams are presented here (JCH)

A Three-dimensional Topological Model of Ternary Phase Diagram

International Nuclear Information System (INIS)

Mu, Yingxue; Bao, Hong

2017-01-01

In order to obtain a visualization of the complex internal structure of ternary phase diagram, the paper realized a three-dimensional topology model of ternary phase diagram with the designed data structure and improved algorithm, under the guidance of relevant theories of computer graphics. The purpose of the model is mainly to analyze the relationship between each phase region of a ternary phase diagram. The model not only obtain isothermal section graph at any temperature, but also extract a particular phase region in which users are interested. (paper)

Recent developments in Bayesian inference of tokamak plasma equilibria and high-dimensional stochastic quadratures

International Nuclear Information System (INIS)

Von Nessi, G T; Hole, M J

2014-01-01

We present recent results and technical breakthroughs for the Bayesian inference of tokamak equilibria using force-balance as a prior constraint. Issues surrounding model parameter representation and posterior analysis are discussed and addressed. These points motivate the recent advancements embodied in the Bayesian Equilibrium Analysis and Simulation Tool (BEAST) software being presently utilized to study equilibria on the Mega-Ampere Spherical Tokamak (MAST) experiment in the UK (von Nessi et al 2012 J. Phys. A 46 185501). State-of-the-art results of using BEAST to study MAST equilibria are reviewed, with recent code advancements being systematically presented though out the manuscript. (paper)

Carbides crystalline structure of AISI M2 high-speed steel

International Nuclear Information System (INIS)

Serna, M.M.; Galego, E.; Rossi, J.L.

2005-01-01

The aim of this study was to identify the crystallographic structure of the extracted carbides of AISI M2 steel spray formed The structure determination of these carbides. The structure determination of these carbides is a very hard work. Since these structures were formed by atom migration it is not possible to reproduce them by a controlled process with a determined chemical composition. The solution of this problem is to obtain the carbide by chemical extraction from the steel. (Author)

Phase diagrams and heterogeneous equilibria a practical introduction

CERN Document Server

Predel, Bruno; Pool, Monte

2004-01-01

This graduate-level textbook provides an introduction to the practical application of phase diagrams. It is intended for students and researchers in chemistry, metallurgy, mineralogy, and materials science as well as in engineering and physics. Heterogeneous equilibria are described by a minimum of theory illustrated by practical examples and realistic case discussions from the different fields of application. The treatment of the physical and energetic background of phase equilibria leads to the discussion of the thermodynamics of mixtures and the correlation between energetics and composition. Thus, tools for the prediction of energetic, structural, and physical quantities are provided. The authors treat the nucleation of phase transitions, the production and stability of technologically important metastable phases, and metallic glasses. Furthermore, the text also concisely presents the thermodynamics and composition of polymer systems.

Extended Group Contribution Model for Polyfunctional Phase Equilibria

DEFF Research Database (Denmark)

Abildskov, Jens

of physical separation processes. In a thermodynamic sense, design requires detailed knowledge of activity coefficients in the phases at equilibrium. The prediction of these quantities from a minimum of experimental data is the broad scope of this thesis. Adequate equations exist for predicting vapor......Material and energy balances and equilibrium data form the basis of most design calculations. While material and energy balances may be stated without much difficulty, the design engineer is left with a choice between a wide variety of models for describing phase equilibria in the design......-liquid equilibria from data on binary mixtures, composed of structurally simple molecules with a single functional group. More complex is the situation with mixtures composed of structurally more complicated molecules or molecules with more than one functional group. The UNIFAC method is extended to handle...

Structure and thermal expansion of NbC complex carbides

International Nuclear Information System (INIS)

Khatsinskaya, I.M.; Chaporova, I.N.; Cheburaeva, R.F.; Samojlov, A.I.; Logunov, A.V.; Ignatova, I.A.; Dodonova, L.P.

1983-01-01

Alloying dependences of the crystal lattice parameters at indoor temperature and coefficient of thermal linear exspansion within a 373-1273 K range are determined for complex NbC-base carbides by the method of mathematical expemental design. It is shown that temperature changes in the linear expansion coefficient of certain complex carbides as distinct from NbC have an anomaly (minimum) within 773-973 K caused by occurring reversible phase transformations. An increase in the coefficient of thermal linear expansion and a decrease in hardness of NbC-base tungsten-, molybdenum-, vanadium- and hafnium-alloyed carbides show a weakening of a total chemical bond in the complex carbides during alloying

Impact of ternary blends of biodiesel on diesel engine performance

Directory of Open Access Journals (Sweden)

Prem Kumar

2016-06-01

Full Text Available The Pongamia and waste cooking oils are the main non edible oils for biodiesel production in India. The aim of the present work is to evaluate the fuel properties and investigate the impact on engine performance using Pongamia and waste cooking biodiesel and their ternary blend with diesel. The investigation of the fuel properties shows that Pongamia biodiesel and waste cooking biodiesel have poor cold flow property. This will lead to starting problem in the engine operation. To overcome this problem the ternary blends of diesel, waste cooking biodiesel and Pongamia biodiesel are prepared. The cloud and pour point for ternary blend, (WCB20:PB20:D60 were found to be 7 °C and 6.5 °C which are comparable to cloud and pour point of diesel 6 °C and 5 °C, respectively. The result of the test showed that brake specific fuel consumption for Pongamia biodiesel and waste cooking biodiesel is higher than ternary blend, (WCB20:PB20:D60 due to their lower energy content. The brake thermal efficiency of ternary blend and diesel is comparable while the Pongamia and waste cooking biodiesel have low efficiency. The result of investigation showed that ternary blend can be developed as alternate fuel.

Charge distribution in the ternary fragmentation of {sup 252}Cf

Energy Technology Data Exchange (ETDEWEB)

Senthil Kannan, M.T.; Balasubramaniam, M. [Bharathiar University, Department of Physics, Coimbatore (India)

2017-08-15

We present here, for the first time, a study on ternary fragmentation charge distribution of {sup 252}Cf using the convolution integral method and the statistical theory. The charge distribution for all possible charge combinations of a ternary breakup are grouped as a bin containing different mass partitions. Different bins corresponding to various third fragments with mass numbers from A{sub 3} = 16 to 84 are identified with the available experimental masses. The corresponding potential energy surfaces are calculated using the three cluster model for the two arrangements A{sub 1} + A{sub 2} + A{sub 3} and A{sub 1} + A{sub 3} + A{sub 2}. The ternary fragmentation yield values are calculated for the ternary combination from each bin possessing minimum potential energy. The yields of the resulting ternary combinations as a function of the charge numbers of the three fragments are analyzed for both the arrangements. The calculations are carried out at different excitation energies of the parent nucleus. For each excitation energy the temperature of the three fragments are iteratively computed conserving the total energy. The distribution of fragment temperatures corresponding to different excitation energies for some fixed third fragments are discussed. The presence of the closed shell nucleus Sn in the favourable ternary fragmentation is highlighted. (orig.)

On the stability of dissipative MHD equilibria

International Nuclear Information System (INIS)

Teichmann, J.

1979-04-01

The global stability of stationary equilibria of dissipative MHD is studied uisng the direct Liapunov method. Sufficient and necessary conditions for stability of the linearized Euler-Lagrangian system with the full dissipative operators are given. The case of the two-fluid isentropic flow is discussed. (orig.)

Synthesis, characterization and thermoelectric properties of metal borides, boron carbides and carbaborides; Synthese, Charakterisierung und thermoelektrische Eigenschaften ausgewaehlter Metallboride, Borcarbide und Carbaboride

Energy Technology Data Exchange (ETDEWEB)

Guersoy, Murat

2015-07-06

This work reports on the solid state synthesis and structural and thermoelectrical characterization of hexaborides (CaB{sub 6}, SrB{sub 6}, BaB{sub 6}, EuB{sub 6}), diboride dicarbides (CeB{sub 2}C{sub 2}, LaB{sub 2}C{sub 2}), a carbaboride (NaB{sub 5}C) and composites of boron carbide. The characterization was performed by X-ray diffraction methods and Rietveld refinements based on structure models from literature. Most of the compounds were densified by spark plasma sintering at 100 MPa. As high-temperature thermoelectric properties the Seebeck coefficients, electrical conductivities, thermal diffusivities and heat capacities were measured between room temperature and 1073 K. ZT values as high as 0.5 at 1273 K were obtained for n-type conducting EuB{sub 6}. High-temperature X-ray diffraction also confirmed its thermal stability. The solid solutions Ca{sub x}Sr{sub 1-x}B{sub 6}, Ca{sub x}Ba{sub 1-x}B{sub 6} and Sr{sub x}Ba{sub 1-x}B{sub 6} (x = 0, 0.25, 0.5, 0.75, 1) are also n-type but did not show better ZT values for the ternary compounds compared to the binaries, but for CaB{sub 6} the values of the figure of merit (ca. 0.3 at 1073 K) were significantly increased (ca. 50 %) compared to earlier investigations which is attributed to the densification process. Sodium carbaboride, NaB{sub 5}C, was found to be the first p-type thermoelectric material that crystallizes with the hexaboride-structure type. Seebeck coefficients of ca. 80 μV . K{sup -1} were obtained. Cerium diboride dicarbide, CeB{sub 2}C{sub 2}, and lanthanum diboride dicarbide, LaB{sub 2}C{sub 2}, are metallic. Both compounds were used as model compounds to develop compacting strategies for such layered borides. Densities obtained at 50 MPa were determined to be higher than 90 %. A new synthesis route using single source precursors that contain boron and carbon was developed to open the access to new metal-doped boron carbides. It was possible to obtain boron carbide, but metal-doping could not be

Study of the ternary alloy systems Al-Ni-Fe and Al-Cu-Ru with special regard to quasicrystalline phases

International Nuclear Information System (INIS)

Lemmerz, U.

1996-07-01

Two ternary alloy-systems, the Al-Ni-Fe system and the Al-Cu-Ru system were studied with special regard to quasicrystalline phases. Isothermal sections were established in both systems in the stoichiometric area of the quasicrystalline phase. In the Al-Ni-Fe system a new stable decagonal phase was found. Its stoichiometric range is very small around Al 71.6 Ni 23.0 Fe 5.4 . The temperature range in which it is stable lies between 847 and 930 C. The decagonal phase undergoes a eutectoid reaction to the three crystalline phases Al 3 Ni 2 , Al 3 Ni and Al 13 Fe 4 at 847 C. It melts peritectically at 930 C forming Al 13 Fe 4 , Al 3 Ni 2 and a liquid. The investigations in the Al-Cu-Ru system concentrated on the phase equilibria between the icosahedral phase and its neighbouring phases in a temperature range between 600 and 1000 C. The icosahedral phase was observed in the whole temperature range. The investigated stoichiometric area extends down to Al contents of 45%, which allows the fields of existence to be determined for the ternary phases α-AlCuRu, the icosahedral phase and Al 7 Cu 2 Ru. Binary phases were determined down to the upper (high Al content) border of AlRu. No hitherto unknown phase was observed in the investigated area. Rietveld analyses were carried out on α-AlCuRu and Al 7 Cu 2 Ru showing some discrepancies from the α-AlMnSi structure taken as a base for α-AlCuRu and confirming the Al 7 Cu 2 Fe structure for Al 7 Cu 2 Ru. (orig.)

Low temperature study of nonstoichiometric titanium carbide

International Nuclear Information System (INIS)

Tashmetov, M.Yu.

2005-05-01

By low temperature neutron diffraction method was studied structure in nonstoichiometric titanium carbide from room temperature up to 12K. It is found of low temperature phase in titanium carbide- TiC 0.71 . It is established region and borders of this phase. It is determined change of unit cell parameter. (author)

Multiple equilibria in a simple elastocapillary system

KAUST Repository

Taroni, Michele

2012-09-28

We consider the elastocapillary interaction of a liquid drop placed between two elastic beams, which are both clamped at one end to a rigid substrate. This is a simple model system relevant to the problem of surface-tension-induced collapse of flexible micro-channels that has been observed in the manufacture of microelectromechanical systems (MEMS). We determine the conditions under which the beams remain separated, touch at a point, or stick along a portion of their length. Surprisingly, we show that in many circumstances multiple equilibrium states are possible. We develop a lubrication-type model for the flow of liquid out of equilibrium and thereby investigate the stability of the multiple equilibria. We demonstrate that for given material properties two stable equilibria may exist, and show via numerical solutions of the dynamic model that it is the initial state of the system that determines which stable equilibrium is ultimately reached. © 2012 Cambridge University Press.

A Continuous Family of Equilibria in Ferromagnetic Media are Ground States

Science.gov (United States)

Su, Xifeng; de la Llave, Rafael

2017-09-01

We show that a foliation of equilibria (a continuous family of equilibria whose graph covers all the configuration space) in ferromagnetic transitive models are ground states. The result we prove is very general, and it applies to models with long range and many-body interactions. As an application, we consider several models of networks of interacting particles including models of Frenkel-Kontorova type on Z^d and one-dimensional quasi-periodic media. The result above is an analogue of several results in the calculus of variations (fields of extremals) and in PDE's. Since the models we consider are discrete and long range, new proofs need to be given. We also note that the main hypothesis of our result (the existence of foliations of equilibria) is the conclusion (using KAM theory) of several recent papers. Hence, we obtain that the KAM solutions recently established are minimizers when the interaction is ferromagnetic and transitive (these concepts are defined later).

Inverse plasma equilibria

International Nuclear Information System (INIS)

Hicks, H.R.; Dory, R.A.; Holmes, J.A.

1983-01-01

We illustrate in some detail a 2D inverse-equilibrium solver that was constructed to analyze tokamak configurations and stellarators (the latter in the context of the average method). To ensure that the method is suitable not only to determine equilibria, but also to provide appropriately represented data for existing stability codes, it is important to be able to control the Jacobian, tilde J is identical to delta(R,Z)/delta(rho, theta). The form chosen is tilde J = J 0 (rho)R/sup l/rho where rho is a flux surface label, and l is an integer. The initial implementation is for a fixed conducting-wall boundary, but the technique can be extended to a free-boundary model

Density-Driven segregation in Binary and Ternary Granular Systems

NARCIS (Netherlands)

Windows-Yule, Kit; Parker, David

2015-01-01

We present a first experimental study of density-induced segregation within a three-dimensional, vibrofluidised, ternary granular system. Using Positron Emission Particle Tracking (PEPT), we study the steady-state particle distributions achieved by binary and ternary granular beds under a variety of

(Vapour + liquid) equilibria, volumetric and compressibility behaviour of binary and ternary aqueous solutions of 1-hexyl-3-methylimidazolium chloride, methyl potassium malonate, and ethyl potassium malonate

International Nuclear Information System (INIS)

Sadeghi, Rahmat; Mahdavi, Adibeh

2012-01-01

Highlights: ► VLE and volumetry of binary and ternary [C 6 mim][Cl], MPM and EPM aqueous solutions. ► Constant a w lines show small negative deviation from the linear isopiestic relation. ► Solute–water interactions follow the order: EPM > MPM > [C 6 mim][Cl]. ► MPM and EPM have a very weak salting-out effect on [C 6 mim][Cl] aqueous solutions. - Abstract: (Vapour + liquid) equilibrium data (water activity, vapour pressure, osmotic coefficient, and activity coefficient) of binary aqueous solutions of 1-hexyl-3-methylimidazolium chloride ([C 6 mim][Cl]), methyl potassium malonate, and ethyl potassium malonate and ternary {[C 6 mim][Cl] + methyl potassium malonate} and {[C 6 mim][Cl] + ethyl potassium malonate} aqueous solutions were obtained through the isopiestic method at T = 298.15 K. These results reveal that the ionic liquid behaves as surfactant-like and aggregates in aqueous solutions at molality about 0.4 mol · kg −1 . The constant water activity lines of all the ternary systems investigated show small negative deviations from the linear isopiestic relation (Zdanovskii–Stokes–Robinson rule) derived using the semi-ideal hydration model. The density and speed of sound measurements were carried out on solutions of methyl potassium malonate and ethyl potassium malonate in water and of [C 6 mim][Cl] in aqueous solutions of 0.25 mol · kg −1 methyl potassium malonate and ethyl potassium malonate at T = (288.15 to 308.15) K at atmospheric pressure. From the experimental density and speed of sound data, the values of the apparent molar volume, apparent molar isentropic compressibility and excess molar volume were evaluated and from which the infinite dilution apparent molar volume and infinite dilution apparent molar isentropic compressibility were calculated at each temperature. Although, there are no clear differences between the values of the apparent molar volume of [C 6 mim][Cl] in pure water and in methyl potassium malonate or ethyl

Tantalum and niobium carbides obtention by carbothermic reduction of columbotantalite ores

International Nuclear Information System (INIS)

Gordo, E.; Garcia-Carcedo, F.; Torralba, J.M.

1998-01-01

Tantalum and niobium carbides are characterized by its high hardness and chemical corrosion resistance. Both carbides, but mainly TaC, are used in hard metals (sintered carbides), together with their carbides, to manufacture cutting tools and dies in special machining applications involving mechanical shock at high temperature. Its use as reinforcement of wear resistant materials through powder metallurgy techniques are being investigated. However, the use of TaC is usually limited because of its high cost. Therefore tantalum carbide with niobium content, which is cheaper, is used. In this work the obtention of complex tantalum and niobium carbides from a Spanish columbotantalite ore is studied through relatively cheap and simple process as it is carbothermic reduction. Concentration of the ore, its reduction and the characterization of products are described. (Author) 11 refs

Extreme-Environment Silicon-Carbide (SiC) Wireless Sensor Suite

Science.gov (United States)

Yang, Jie

2015-01-01

Phase II objectives: Develop an integrated silicon-carbide wireless sensor suite capable of in situ measurements of critical characteristics of NTP engine; Compose silicon-carbide wireless sensor suite of: Extreme-environment sensors center, Dedicated high-temperature (450 deg C) silicon-carbide electronics that provide power and signal conditioning capabilities as well as radio frequency modulation and wireless data transmission capabilities center, An onboard energy harvesting system as a power source.

Oxide film assisted dopant diffusion in silicon carbide

Energy Technology Data Exchange (ETDEWEB)

Tin, Chin-Che, E-mail: cctin@physics.auburn.ed [Department of Physics, Auburn University, Alabama 36849 (United States); Mendis, Suwan [Department of Physics, Auburn University, Alabama 36849 (United States); Chew, Kerlit [Department of Electrical and Electronic Engineering, Faculty of Engineering and Science, Universiti Tunku Abdul Rahman, Kuala Lumpur (Malaysia); Atabaev, Ilkham; Saliev, Tojiddin; Bakhranov, Erkin [Physical Technical Institute, Uzbek Academy of Sciences, 700084 Tashkent (Uzbekistan); Atabaev, Bakhtiyar [Institute of Electronics, Uzbek Academy of Sciences, 700125 Tashkent (Uzbekistan); Adedeji, Victor [Department of Chemistry, Geology and Physics, Elizabeth City State University, North Carolina 27909 (United States); Rusli [School of Electrical and Electronic Engineering, Nanyang Technological University (Singapore)

2010-10-01

A process is described to enhance the diffusion rate of impurities in silicon carbide so that doping by thermal diffusion can be done at lower temperatures. This process involves depositing a thin film consisting of an oxide of the impurity followed by annealing in an oxidizing ambient. The process uses the lower formation energy of silicon dioxide relative to that of the impurity-oxide to create vacancies in silicon carbide and to promote dissociation of the impurity-oxide. The impurity atoms then diffuse from the thin film into the near-surface region of silicon carbide.

Oxide film assisted dopant diffusion in silicon carbide

International Nuclear Information System (INIS)

Tin, Chin-Che; Mendis, Suwan; Chew, Kerlit; Atabaev, Ilkham; Saliev, Tojiddin; Bakhranov, Erkin; Atabaev, Bakhtiyar; Adedeji, Victor; Rusli

2010-01-01

A process is described to enhance the diffusion rate of impurities in silicon carbide so that doping by thermal diffusion can be done at lower temperatures. This process involves depositing a thin film consisting of an oxide of the impurity followed by annealing in an oxidizing ambient. The process uses the lower formation energy of silicon dioxide relative to that of the impurity-oxide to create vacancies in silicon carbide and to promote dissociation of the impurity-oxide. The impurity atoms then diffuse from the thin film into the near-surface region of silicon carbide.

Looking for multiple equilibria when geography matters : German city growth and the WWII shock

NARCIS (Netherlands)

Bosker, Maarten; Brakman, Steven; Garretsen, Harry; Schramm, Marc

Based on the methodology of Davis and Weinstein, we look for multiple equilibria in German city growth. Bytaking the bombing of Germany during WWII as an example of a large, temporary shock, we analyze whether German city growth is characterized by multiple equilibria. In doing so, we allow for

The ternary systems Sc-Sm(Dy)-Si at 870 K

International Nuclear Information System (INIS)

Kotur, B.Ya.; Mokra, I.Ya.; Toporinskij, A.Ya.

1991-01-01

Isothermal cross sections of the ternary systems Sc-Sm-Si and Sc-Dy-Si at 870 K have been plotted. Investigation of scandium and disprosium in ternary systems have been examined by X-ray diffraction and microstructure analysis. Besides literary data on binary systems Sc-Si, Sm-Si, Dy-Si have been used. Formation of limited (Sc-Sm-Si, Sc-Dy-Si) and continuous (Sc-Dy-Si) solid solutions based on bisilicides of Sc and Sm(Dy) is discovered. Two and five ternary compounds in Sc-Sm-Si and Sc-Dy-Si systems have been determined and their crystal structure has been established. When investigating of Sc-(rare earth element)-Si ternary systems and should take into account the specific interaction of scandium and samarium with REE

Effect of temperature on acid–base equilibria in separation techniques. A review

International Nuclear Information System (INIS)

Gagliardi, Leonardo G.; Tascon, Marcos; Castells, Cecilia B.

2015-01-01

Studies on the theoretical principles of acid–base equilibria are reviewed and the influence of temperature on secondary chemical equilibria within the context of separation techniques, in water and also in aqueous-organic solvent mixtures, is discussed. In order to define the relationships between the retention in liquid chromatography or the migration velocity in capillary electrophoresis and temperature, the main properties of acid–base equilibria have to be taken into account for both, the analytes and the conjugate pairs chosen to control the solution pH. The focus of this review is based on liquid–liquid extraction (LLE), liquid chromatography (LC) and capillary electrophoresis (CE), with emphasis on the use of temperature as a useful variable to modify selectivity on a predictable basis. Simplified models were evaluated to achieve practical optimizations involving pH and temperature (in LLE and CE) as well as solvent composition in reversed-phase LC. - Highlights: • The study of theoretical principles of acid–base equilibrium has been reviewed. • The proton transfer process is often present in the analytical separation practice. • The influence of temperature on secondary chemical equilibria is examined. • The focus is laid on liquid chromatography and capillary electrophoresis. • Temperature can be a useful variable to modify selectivity under predictable basis

Study on the performance of fuel elements with carbide and carbide-nitride fuel

International Nuclear Information System (INIS)

Golovchenko, Yu.M.; Davydov, E.F.; Maershin, A.A.

1985-01-01

Characteristics, test conditions and basic results of material testing of fuel elements with carbide and carbonitride fuel irradiated in the BOR-60 reactor up to 3-10% burn-up at specific power rate of 55-70 kW/m and temperatures of the cladding up to 720 deg C are described. Increase of cladding diameter is stated mainly to result from pressure of swelling fuel. The influence of initial efficient porosity of the fuel on cladding deformation and fuel stoichiometry on steel carbonization is considered. Utilization of carbide and carbonitride fuel at efficient porosity of 20% at the given test modes is shown to ensure their operability up to 10% burn-up

Formation mechanism of spheroidal carbide in ultra-low carbon ductile cast iron

Directory of Open Access Journals (Sweden)

Bin-guo Fu

2016-09-01

Full Text Available The formation mechanism of the spheroidal carbide in the ultra-low carbon ductile cast iron fabricated by the metal mold casting technique was systematically investigated. The results demonstrated that the spheroidal carbide belonged to eutectic carbide and crystallized in the isolated eutectic liquid phase area. The formation process of the spheroidal carbide was related to the contact and the intersection between the primary dendrite and the secondary dendrite of austenite. The oxides of magnesium, rare earths and other elements can act as heterogeneous nucleation sites for the spheroidal carbide. It was also found that the amount of the spheroidal carbide would increase with an increase in carbon content. The cooling rate has an important influence on the spheroidal carbide under the same chemical composition condition.

Experimental study of the ternary Ag-Cu-In phase diagram

International Nuclear Information System (INIS)

Bahari, Zahra; Elgadi, Mohamed; Rivet, Jacques; Dugue, Jerome

2009-01-01

The phase diagram of the Ag-Cu-In system was investigated using powder X-ray diffraction (XRD), differential scanning calorimetry (DSC) and electron probe microanalysis (EPMA). Two isothermal sections (at 510 and 607 deg. C) and 15 isopletic sections were studied. The results showed seven ternary peritectics, one ternary eutectic and one ternary metatectic. A complete reaction scheme was constructed, the valleys were drawn and the liquidus surfaces were derived from DSC data in the entire composition range.

Experimental study of the ternary Ag-Cu-In phase diagram

Energy Technology Data Exchange (ETDEWEB)

Bahari, Zahra [Laboratoire de chimie physique et minerale, Faculte des sciences pharmaceutiques et biologiques, Universite Paris Descartes, avenue de l' Observatoire, 75006 Paris (France); Laboratoire de chimie du solide mineral (LCSM), Faculte des sciences, Universite Mohamed 1er, Route Sidi Maafa, B.P. 524, Oujda, Maroc (Morocco); Elgadi, Mohamed [Laboratoire de chimie du solide mineral (LCSM), Faculte des sciences, Universite Mohamed 1er, Route Sidi Maafa, B.P. 524, Oujda, Maroc (Morocco); Rivet, Jacques [Laboratoire de chimie physique et minerale, Faculte des sciences pharmaceutiques et biologiques, Universite Paris Descartes, avenue de l' Observatoire, 75006 Paris (France); Dugue, Jerome [Laboratoire de chimie physique et minerale, Faculte des sciences pharmaceutiques et biologiques, Universite Paris Descartes, avenue de l' Observatoire, 75006 Paris (France)], E-mail: jerome.dugue@univ-paris5.fr

2009-05-27

The phase diagram of the Ag-Cu-In system was investigated using powder X-ray diffraction (XRD), differential scanning calorimetry (DSC) and electron probe microanalysis (EPMA). Two isothermal sections (at 510 and 607 deg. C) and 15 isopletic sections were studied. The results showed seven ternary peritectics, one ternary eutectic and one ternary metatectic. A complete reaction scheme was constructed, the valleys were drawn and the liquidus surfaces were derived from DSC data in the entire composition range.

High-field superconductivity in the Nb-Ti-Zr ternary system

International Nuclear Information System (INIS)

Ralls, K.M.; Rose, R.M.; Wulff, J.

1980-01-01

Resistive critical current densities, critical fields, and normal-state electrical resistivities were obtained at 4.2 0 K for 55 alloys in the Nb-Ti-Zr ternary alloy system, excepting Ti-Zr binary compositions. The resistive critical field as a function of ternary composition has a saddle point between the Nb-Ti and Nb-Zr binaries, so that ternary alloying in this system is not expected to result in higher critical fields than the binary alloys

High-field superconductivity in the Nb-Ti-Zr ternary system

Science.gov (United States)

Ralls, K. M.; Rose, R. M.; Wulff, J.

1980-06-01

Resistive critical current densities, critical fields, and normal-state electrical resistivities were obtained at 4.2 °K for 55 alloys in the Nb-Ti-Zr ternary alloy system, excepting Ti-Zr binary compositions. The resistive critical field as a function of ternary composition has a saddle point between the Nb-Ti and Nb-Zr binaries, so that ternary alloying in this system is not expected to result in higher critical fields than the binary alloys.

Ternary System with Controlled Structure: A New Strategy toward Efficient Organic Photovoltaics.

Science.gov (United States)

Cheng, Pei; Wang, Rui; Zhu, Jingshuai; Huang, Wenchao; Chang, Sheng-Yung; Meng, Lei; Sun, Pengyu; Cheng, Hao-Wen; Qin, Meng; Zhu, Chenhui; Zhan, Xiaowei; Yang, Yang

2018-02-01

Recently, a new type of active layer with a ternary system has been developed to further enhance the performance of binary system organic photovoltaics (OPV). In the ternary OPV, almost all active layers are formed by simple ternary blend in solution, which eventually leads to the disordered bulk heterojunction (BHJ) structure after a spin-coating process. There are two main restrictions in this disordered BHJ structure to obtain higher performance OPV. One is the isolated second donor or acceptor domains. The other is the invalid metal-semiconductor contact. Herein, the concept and design of donor/acceptor/acceptor ternary OPV with more controlled structure (C-ternary) is reported. The C-ternary OPV is fabricated by a sequential solution process, in which the second acceptor and donor/acceptor binary blend are sequentially spin-coated. After the device optimization, the power conversion efficiencies (PCEs) of all OPV with C-ternary are enhanced by 14-21% relative to those with the simple ternary blend; the best PCEs are 10.7 and 11.0% for fullerene-based and fullerene-free solar cells, respectively. Moreover, the averaged PCE value of 10.4% for fullerene-free solar cell measured in this study is in great agreement with the certified one of 10.32% obtained from Newport Corporation. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Highly thermal conductive carbon fiber/boron carbide composite material

International Nuclear Information System (INIS)

Chiba, Akio; Suzuki, Yasutaka; Goto, Sumitaka; Saito, Yukio; Jinbo, Ryutaro; Ogiwara, Norio; Saido, Masahiro.

1996-01-01

In a composite member for use in walls of a thermonuclear reactor, if carbon fibers and boron carbide are mixed, since they are brought into contact with each other directly, boron is reacted with the carbon fibers to form boron carbide to lower thermal conductivity of the carbon fibers. Then, in the present invention, graphite or amorphous carbon is filled between the carbon fibers to provide a fiber bundle of not less than 500 carbon fibers. Further, the surface of the fiber bundle is coated with graphite or amorphous carbon to suppress diffusion or solid solubilization of boron to carbon fibers or reaction of them. Then, lowering of thermal conductivity of the carbon fibers is prevented, as well as the mixing amount of the carbon fiber bundles with boron carbide, a sintering temperature and orientation of carbon fiber bundles are optimized to provide a highly thermal conductive carbon fiber/boron carbide composite material. In addition, carbide or boride type short fibers, spherical graphite, and amorphous carbon are mixed in the boron carbide to prevent development of cracks. Diffusion or solid solubilization of boron to carbon fibers is reduced or reaction of them if the carbon fibers are bundled. (N.H.)

Design, Fabrication and Performance of Boron-Carbide Control Elements

International Nuclear Information System (INIS)

Brammer, H.A.; Jacobson, J.

1964-01-01

A control blade design, incorporating boron-carbide (B 4 C) in stainless-steel tubes, was introduced into service in boiling water reactors in April 1961. Since that time this blade has become the standard reference control element in General Electric boiling-water reactors, replacing the 2% boron-stainless-steel blades previously used. The blades consist of a sheathed, cruciform array of small vertical stainless-steel tubes filled with compácted boron-carbide powder. The boron-carbide powder is confined longitudinally into several independent compartments by swaging over ball bearings located inside the tubes. The development and use of boron-carbide control rods is discussed in five phases: 1. Summary of experience with boron-steel blades and reasons for transition to boron-carbide control; 2. Design of the boron-carbide blade, beginning with developmental experiments, including early measurements performed in the AEC ''Control Rod Material and Development Program'' at the Vallecitos Atomic Laboratory, through a description of the final control blade configuration; 3. Fabrication of the blades and quality control procedures; 4. Results of confirmatory pre-operational mechanical and reactivity testing; and 5. Post-operational experience with the blades, including information on the results of mechanical inspection and reactivity testing after two years of reactor service. (author) [fr

Calculation of Binary Adsorption Equilibria: Hydrocarbons and Carbon Dioxide on Activated Carbon

DEFF Research Database (Denmark)

Marcussen, Lis; Krøll, A.

1999-01-01

Binary adsorption equilibria are calculated by means of a mathematical model for multicomponent mixtures combined with the SPD (Spreading Pressure Dependent) model for calculation of activity coefficients in the adsorbed phase. The model has been applied successfully for the adsorption of binary ...... mixtures of hydrocarbons and carbon dioxide on activated carbons. The model parameters have been determined, and the model has proven to be suited for prediction of adsorption equilibria in the investigated systems....

Elastic modulus and fracture of boron carbide

International Nuclear Information System (INIS)

Hollenberg, G.W.; Walther, G.

1978-12-01

The elastic modulus of hot-pressed boron carbide with 1 to 15% porosity was measured at room temperature. K/sub IC/ values were determined for the same porosity range at 500 0 C by the double torsion technique. The critical stress intensity factor of boron carbide with 8% porosity was evaluated from 25 to 1200 0 C

Iron Carbides in Fischer–Tropsch Synthesis: Theoretical and Experimental Understanding in Epsilon-Iron Carbide Phase Assignment

International Nuclear Information System (INIS)

Liu, Xing-Wu; Cao, Zhi; Zhao, Shu; Gao, Rui

2017-01-01

As active phases in low-temperature Fischer–Tropsch synthesis for liquid fuel production, epsilon iron carbides are critically important industrial materials. However, the precise atomic structure of epsilon iron carbides remains unclear, leading to a half-century of debate on the phase assignment of the ε-Fe 2 C and ε’-Fe 2.2 C. Here, we resolve this decades-long question by a combining theoretical and experimental investigation to assign the phases unambiguously. First, we have investigated the equilibrium structures and thermal stabilities of ε-Fe x C, (x = 1, 2, 2.2, 3, 4, 6, 8) by first-principles calculations. We have also acquired X-ray diffraction patterns and Mössbauer spectra for these epsilon iron carbides, and compared them with the simulated results. These analyses indicate that the unit cell of ε-Fe 2 C contains only one type of chemical environment for Fe atoms, while ε’-Fe 2.2 C has six sets of chemically distinct Fe atoms.

Reduction of metal oxides in metal carbide fusion superheated with plasma

Energy Technology Data Exchange (ETDEWEB)

Hedai, L

1981-01-01

A significant part of metals is capable of binding a high quantity of carbon in the form of carbide. The carbide fusion produced as a result of smelting and superheating, metal carbides with the use of plasma might be a medium to be utilized for the reduction of different metal oxides, whilst also the original carbide structure of the metal carbides will be reduced to metallic structure. The experiments conducted by making use of plasma equipment, of 20, 55 and 100 kW performances are described. On the basis of the results of the experiments performed, the following statements are to be made. The oxide reductions taking place in the metal carbide fusion might also be carried out in open-hearth furnaces, because reducing atmosphere is not necessitated during this procedure. The quantity of energy required is basically defined by the energy needed for smelting and superheating the metal carbide. The method for producing the metal described may be mainly applied for the allied production of high-purity steels as well as for that of ferro-alloys.

Extensive Evaluation of the Conductor-like Screening Model for Real Solvents Method in Predicting Liquid-Liquid Equilibria in Ternary Systems of Ionic Liquids with Molecular Compounds.

Science.gov (United States)

Paduszyński, Kamil

2018-04-12

A conductor-like screening model for real solvents (COSMO-RS) is nowadays one of the most popular and commonly applied tools for the estimation of thermodynamic properties of complex fluids. The goal of this work is to provide a comprehensive review and analysis of the performance of this approach in calculating liquid-liquid equilibrium (LLE) phase diagrams in ternary systems composed of ionic liquid and two molecular compounds belonging to diverse families of chemicals (alkanes, aromatics, S/N-compounds, alcohols, ketones, ethers, carboxylic acid, esters, and water). The predictions are presented for extensive experimental database, including 930 LLE data sets and more than 9000 data points (LLE tie lines) reported for 779 unique ternary mixtures. An impact of the type of molecular binary subsystem on the accuracy of predictions is demonstrated and discussed on the basis of representative examples. The model's capability of capturing qualitative trends in the LLE distribution ratio and selectivity is also checked for a number of structural effects. Comparative analysis of two levels of quantum chemical theory (BP-TZVP-COSMO vs BP-TZVPD-FINE) for the input molecular data for COSMO-RS is presented. Finally, some general recommendations for the applicability of the model are indicated based on the analysis of the global performance as well as on the results obtained for systems relevant from the point of view of important separation problems.

The valve effect of the carbide interlayer of an electric resistance plug

International Nuclear Information System (INIS)

Lakomskii, V.

1998-01-01

The welded electric resistance plug (ERP) usually contains a carbide interlayer at the plug-carbon material interface. The interlayer forms during welding the contact metallic alloy with the carbon material when the oxide films of the alloy are reduced on the interface surface by carbon to the formation of carbides and the surface layer of the plug material dissolves carbon to saturation. Subsequently, during solidification of the plug material it forms carbides with the alloy components. The structural composition of the carbide interlayer is determined by the chemical composition of the contact alloy. In alloys developed by the author and his colleagues the carbide forming elements are represented in most cases by silicon and titanium and, less frequently, by chromium and manganese. Therefore, the carbide interlayers in the ERP consisted mainly of silicon and titanium carbides

Computing Proper Equilibria of Zero-Sum Games

DEFF Research Database (Denmark)

Miltersen, Peter Bro; Sørensen, Troels Bjerre

2007-01-01

We show that a proper equilibrium of a matrix game can be found in polynomial time by solving a linear (in the number of pure strategies of the two players) number of linear programs of roughly the same dimensions as the standard linear programs describing the Nash equilibria of the game....

On the stochastic stability of MHD equilibria

International Nuclear Information System (INIS)

Teichmann, J.

1979-07-01

The stochastic stability in the large of stationary equilibria of ideal and dissipative magnetohydrodynamics under the influence of stationary random fluctuations is studied using the direct Liapunov method. Sufficient and necessary conditions for stability of the linearized Euler-Lagrangian systems are given. The destabilizing effect of stochastic fluctuations is demonstrated. (orig.)

Production of silicon carbide bodies

International Nuclear Information System (INIS)

Parkinson, K.

1981-01-01

A body consisting essentially of a coherent mixture of silicon carbide and carbon for subsequent siliconising is produced by casting a slip comprising silicon carbide and carbon powders in a porous mould. Part of the surface of the body, particularly internal features, is formed by providing within the mould a core of a material which retains its shape while casting is in progress but is compressed by shrinkage of the cast body as it dries and is thereafter removable from the cast body. Materials which are suitable for the core are expanded polystyrene and gelatinous products of selected low elastic modulus. (author)

High yield silicon carbide prepolymers

International Nuclear Information System (INIS)

Baney, R.H.

1982-01-01

Prepolymers which exhibit good handling properties, and are useful for preparing ceramics, silicon carbide ceramic materials and articles containing silicon carbide, are polysilanes consisting of 0 to 60 mole% (CH 3 ) 2 Si units and 40 to 100 mole% CH 3 Si units, all Si valences being satisfied by CH 3 groups, other Si atoms, or by H atoms, the latter amounting to 0.3 to 2.1 weight% of the polysilane. They are prepared by reducing the corresponding chloro- or bromo-polysilanes with at least the stoichiometric amount of a reducing agent, e.g. LiAlH 4 . (author)

Computational study of the influence of mirror parameters on FRC (field-reversed configuration) equilibria:

International Nuclear Information System (INIS)

Fuentes, N.O.; Sakanaka, P.H.

1990-01-01

Field-reversed configuration equilibria are studied by solving the Grad-Shafranov equation. A multiple coil system (main coil and end mirrors) is considered to simulate the coil geometry of CNEA device. First results are presented for computed two-dimensional FRC equilibria produced varying the mirror coil current with two different mirror lenghts. (Author)

Positron annihilation lifetime study of interfaces in ternary polymer blends

International Nuclear Information System (INIS)

Meghala, D; Ramya, P; Pasang, T; Raj, J M; Ranganathaiah, C; Williams, J F

2013-01-01

A new method based on positron lifetime spectroscopy is developed to characterize individual interfaces in ternary polymer blends and hence determine the composition dependent miscibility level. The method owes its origin to the Kirkwood-Risemann-Zimm (KRZ) model for the evaluation of the hydrodynamic interaction parameters (α ij ) which was used successfully for a binary blend with a single interface. The model was revised for the present work for ternary polymer blends to account for three interfaces. The efficacy of this method is shown for two ternary blends namely poly(styrene-co-acrylonitrile)/poly (ethylene-co-vinylacetate)/poly(vinyl chloride) (SAN/EVA/PVC) and polycaprolactone /poly(styrene-co-acrylonitrile)/poly(vinyl chloride) (PCL/SAN/PVC) at different compositions. An effective hydrodynamic interaction parameter, α eff , was introduced to predict the overall miscibility of ternary blends.

Signaling equilibria in sensorimotor interactions.

Science.gov (United States)

Leibfried, Felix; Grau-Moya, Jordi; Braun, Daniel A

2015-08-01

Although complex forms of communication like human language are often assumed to have evolved out of more simple forms of sensorimotor signaling, less attention has been devoted to investigate the latter. Here, we study communicative sensorimotor behavior of humans in a two-person joint motor task where each player controls one dimension of a planar motion. We designed this joint task as a game where one player (the sender) possesses private information about a hidden target the other player (the receiver) wants to know about, and where the sender's actions are costly signals that influence the receiver's control strategy. We developed a game-theoretic model within the framework of signaling games to investigate whether subjects' behavior could be adequately described by the corresponding equilibrium solutions. The model predicts both separating and pooling equilibria, in which signaling does and does not occur respectively. We observed both kinds of equilibria in subjects and found that, in line with model predictions, the propensity of signaling decreased with increasing signaling costs and decreasing uncertainty on the part of the receiver. Our study demonstrates that signaling games, which have previously been applied to economic decision-making and animal communication, provide a framework for human signaling behavior arising during sensorimotor interactions in continuous and dynamic environments. Copyright © 2015 Elsevier B.V. All rights reserved.

Iron Carbides and Nitrides: Ancient Materials with Novel Prospects.

Science.gov (United States)

Ye, Zhantong; Zhang, Peng; Lei, Xiang; Wang, Xiaobai; Zhao, Nan; Yang, Hua

2018-02-07

Iron carbides and nitrides have aroused great interest in researchers, due to their excellent magnetic properties, good machinability and the particular catalytic activity. Based on these advantages, iron carbides and nitrides can be applied in various areas such as magnetic materials, biomedical, photo- and electrocatalysis. In contrast to their simple elemental composition, the synthesis of iron carbides and nitrides still has great challenges, particularly at the nanoscale, but it is usually beneficial to improve performance in corresponding applications. In this review, we introduce the investigations about iron carbides and nitrides, concerning their structure, synthesis strategy and various applications from magnetism to the catalysis. Furthermore, the future prospects are also discussed briefly. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Existence of three-dimensional ideal-magnetohydrodynamic equilibria with current sheets

Energy Technology Data Exchange (ETDEWEB)

Loizu, J. [Max-Planck-Institut für Plasmaphysik, D-17491 Greifswald (Germany); Princeton Plasma Physics Laboratory, PO Box 451, Princeton, New Jersey 08543 (United States); Hudson, S. R.; Bhattacharjee, A.; Lazerson, S. [Princeton Plasma Physics Laboratory, PO Box 451, Princeton, New Jersey 08543 (United States); Helander, P. [Max-Planck-Institut für Plasmaphysik, D-17491 Greifswald (Germany)

2015-09-15

We consider the linear and nonlinear ideal plasma response to a boundary perturbation in a screw pinch. We demonstrate that three-dimensional, ideal-MHD equilibria with continuously nested flux-surfaces and with discontinuous rotational-transform across the resonant rational-surfaces are well defined and can be computed both perturbatively and using fully nonlinear equilibrium calculations. This rescues the possibility of constructing MHD equilibria with current sheets and continuous, smooth pressure profiles. The results predict that, even if the plasma acts as a perfectly conducting fluid, a resonant magnetic perturbation can penetrate all the way into the center of a tokamak without being shielded at the resonant surface.

Nash equilibria in quantum games with generalized two-parameter strategies

International Nuclear Information System (INIS)

Flitney, Adrian P.; Hollenberg, Lloyd C.L.

2007-01-01

In the Eisert protocol for 2x2 quantum games [J. Eisert, et al., Phys. Rev. Lett. 83 (1999) 3077], a number of authors have investigated the features arising from making the strategic space a two-parameter subset of single qubit unitary operators. We argue that the new Nash equilibria and the classical-quantum transitions that occur are simply an artifact of the particular strategy space chosen. By choosing a different, but equally plausible, two-parameter strategic space we show that different Nash equilibria with different classical-quantum transitions can arise. We generalize the two-parameter strategies and also consider these strategies in a multiplayer setting

Microhardness and grain size of disordered nonstoichiometric titanium carbide

International Nuclear Information System (INIS)

Lipatnikov, V.N.; Zueva, L.V.; Gusev, A.I.

1999-01-01

Effect of the disordered nonstoichiometric titanium carbide on its microhardness and grain size is studied. It is established that decrease in defectiveness of carbon sublattice of disordered carbide is accompanied by microhardness growth and decrease in grain size. Possible causes of the TiC y microhardness anomalous behaviour in the area 0.8 ≤ y ≤ 0.9 connected with plastic deformation mechanism conditioned by peculiarities of the electron-energetic spectrum of nonstoichiometric carbide are discussed [ru

Vapor-liquid equilibria for the acetone-ethanol-n-propanol-tert-butanol-water system

Energy Technology Data Exchange (ETDEWEB)

Tochigi, K.; Uchida, K.; Kojima, K.

1981-12-01

This study deals with the measurement of vapor-liquid equilibria for the five-component system acetone-ethanol-n-propanol-tert-butanol-water at 760 mmHg and prediction of vapor-liquid equilibria by the ASOG group contribution method. The five-component system in this work is composed of a part of the components obtained during ethanol production by vapor-phase hydration of ethylene. 6 refs.

Active carbon supported molybdenum carbides for higher alcohols synthesis from syngas

DEFF Research Database (Denmark)

Wu, Qiongxiao; Chiarello, Gian Luca; Christensen, Jakob Munkholt

This work provides an investigation of the high pressure CO hydrogenation to higher alcohols on K2CO3 promoted active carbon supported molybdenum carbide. Both activity and selectivity to alcohols over supported molybdenum carbides increased significantly compared to bulk carbides in literatures...

Growth and structure of carbide nanorods

International Nuclear Information System (INIS)

Lieber, C.M.; Wong, E.W.; Dai, H.; Maynor, B.W.; Burns, L.D.

1996-01-01

Recent research on the growth and structure of carbide nanorods is reviewed. Carbide nanorods have been prepared by reacting carbon nanotubes with volatile transition metal and main group oxides and halides. Using this approach it has been possible to obtain solid carbide nanorods of TiC, SiC, NbC, Fe 3 C, and BC x having diameters between 2 and 30 nm and lengths up to 20 microm. Structural studies of single crystal TiC nanorods obtained through reactions of TiO with carbon nanotubes show that the nanorods grow along both [110] and [111] directions, and that the rods can exhibit either smooth or saw-tooth morphologies. Crystalline SiC nanorods have been produced from reactions of carbon nanotubes with SiO and Si-iodine reactants. The preferred growth direction of these nanorods is [111], although at low reaction temperatures rods with [100] growth axes are also observed. The growth mechanisms leading to these novel nanomaterials have also been addressed. Temperature dependent growth studies of TiC nanorods produced using a Ti-iodine reactant have provided definitive proof for a template or topotactic growth mechanism, and furthermore, have yielded new TiC nanotube materials. Investigations of the growth of SiC nanorods show that in some cases a catalytic mechanism may also be operable. Future research directions and applications of these new carbide nanorod materials are discussed

Thermal decomposition of cesium-ethylene-ternary graphite intercalation compounds

International Nuclear Information System (INIS)

Matsumoto, R.; Oishi, Y.; Arii, T.

2010-01-01

In this paper, the thermal decomposition of air-stable Cs-ethylene-ternary graphite intercalation compounds (GICs) is discussed. The air stability of Cs-GICs is improved remarkably after the absorption of ethylene into their interlayer nanospace, because the ethylene molecules oligomerize and block the movement of Cs atoms. In addition, the evaporation of Cs atoms from the Cs-ethylene-ternary GICs is observed above 400 o C under a N 2 atmosphere of 100 Pa by ion attachment mass spectrometry. Although the results indicate that Cs-ethylene-ternary GICs remain stable up to approximately 400 o C, their thermal stability is not very high as compared to that of Cs-GICs.

Embedding complete ternary tree in hypercubes using AVL trees

NARCIS (Netherlands)

S.A. Choudum; I. Raman (Indhumathi)

2008-01-01

htmlabstractA complete ternary tree is a tree in which every non-leaf vertex has exactly three children. We prove that a complete ternary tree of height h, TTh, is embeddable in a hypercube of dimension . This result coincides with the result of [2]. However, in this paper, the embedding utilizes

Thermionic emission of cermets made of refractory carbides

International Nuclear Information System (INIS)

Samsonow, G.W.; Bogomol, I.W.; Ochremtschuk, L.N.; Podtschernjajewa, I.A.; Fomenko, W.S.

1975-01-01

In order to improve the resistance to thermal variations of refractory carbides having good behavior for thermionic emission, they have been combined with transition metals d. Thermionic emission was studied with cermets in compact samples. Following systems were examined: TiC-Nb, TiC-Mo, TiC-W, ZrC-Nb, ZrC-Mo, ZrC-W, WC-Mo with compositions of: 75% M 1 C-25% M 2 , 50%M 1 C-50%M 2 , 25%M 1 C-75%M 2 . When following the variation of electron emission energy phi versus the composition, it appears that in the range of mixed crystals (M 1 M 2 )C, phi decreases and the resistance to thermal variations of these phases is higher than that of individual carbides. The study of obtained cermets shows that their resistance to thermal variations is largely superior to the one of starting carbides; TiC and ZrC carbides, combined with molybdenum and tungsten support the highest number of thermic cycles

Silicon carbide microsystems for harsh environments

CERN Document Server

Wijesundara, Muthu B J

2011-01-01

Silicon Carbide Microsystems for Harsh Environments reviews state-of-the-art Silicon Carbide (SiC) technologies that, when combined, create microsystems capable of surviving in harsh environments, technological readiness of the system components, key issues when integrating these components into systems, and other hurdles in harsh environment operation. The authors use the SiC technology platform suite the model platform for developing harsh environment microsystems and then detail the current status of the specific individual technologies (electronics, MEMS, packaging). Additionally, methods

Energy dissipation in the process of ternary fission in heavy nuclear reaction

International Nuclear Information System (INIS)

Li Xian; Wang Chengqian; Yan Shiwei

2015-01-01

We studied the evolution of the collective motion, interaction potential, the total kinetic and excitation energies in ternary fissions of 197 Au + 197 Au system at 15 MeV/u, and discussed energy dissipation of this reaction. Through the comparison with energy-angle correlation data in binary fissions, we preliminarily concluded that the rst fission of ternary fission was an extreme deep-inelastic process. We further analyzed the correlation of the total kinetic energy with impact parameters in both binary and ternary reactions, and found that the total energy of binary reactions systems was lost about 150 MeV more than ternary fission with small impact parameters, and with larger impact parameters the total energy of ternary reactions were lost 300 MeV more than binary reactions. (authors)

(Solid + liquid) phase equilibria of (Ca(H2PO2)2 + CaCl2 + H2O) and (Ca(H2PO2)2 + NaH2PO2 + H2O) ternary systems at T = 323.15 K

International Nuclear Information System (INIS)

Cao, Hong-yu; Zhou, Huan; Bai, Xiao-qin; Ma, Ruo-xin; Tan, Li-na; Wang, Jun-min

2016-01-01

Graphical abstract: Solubility diagram of the (Ca(H 2 PO 2 ) 2 + NaH 2 PO 2 + H 2 O) system at T = (323.15 and 298.15) K. - Highlights: • Phase diagrams of Ca 2+ -H 2 PO 2 − -Cl − -H 2 O, Ca 2+ -Na + -H 2 PO 2 − -H 2 O at 323.15 K were obtained. • Incompatible double salt of NaCa(H 2 PO 2 ) 3 in Ca 2+ -Na + -H 2 PO 2 − -H 2 O system was determined. • Density diagram of the corresponding liquid were simultaneously measured. - Abstract: Calcium hypophosphite has been widely used as an anti-corrosive agent, flame retardant, fertilizer, assistant for Ni electroless plating, and animal nutritional supplement. High purity calcium hypophosphite can be synthesized via the replacement reaction of sodium hypophosphite and calcium chloride. In this work, the (solid + liquid) phase equilibria of (Ca(H 2 PO 2 ) 2 + CaCl 2 + H 2 O) and (Ca(H 2 PO 2 ) 2 + NaH 2 PO 2 + H 2 O) ternary systems at T = 323.15 K were studied experimentally via the classical isothermal solubility equilibrium method, and the phase diagrams for these two systems were obtained. It was found that two solid salts of CaCl 2 ·2H 2 O and Ca(H 2 PO 2 ) 2 exist in the (Ca(H 2 PO 2 ) 2 + CaCl 2 + H 2 O) system, and three salts of Ca(H 2 PO 2 ) 2 , NaH 2 PO 2 ·H 2 O and one incompatible double salt, NaCa(H 2 PO 2 ) 3 occur in the (Ca(H 2 PO 2 ) 2 + NaH 2 PO 2 + H 2 O) system.

Density-functional study on the equilibria in the ThDP activation.

Science.gov (United States)

Delgado, Eduardo J; Alderete, Joel B; Jaña, Gonzalo A

2011-11-01

The equilibria among the various ionization and tautomeric states involved in the activation of ThDP is addressed using high level density functional theory calculations, X3LYP/6-311++G(d,p)//X3LYP(PB)/6-31++G(d,p). This study provides the first theoretically derived thermodynamic data for the internal equilibria in the activation of ThDP. The role of the medium polarity on the geometry and thermodynamics of the diverse equilibria of ThDP is addressed. The media chosen are cyclohexane and water, as paradigms of apolar and polar media. The results suggest that all ionization and tautomeric states are accessible during the catalytic cycle, even in the absence of substrate, being APH(+) the form required to interconvert the AP and IP tautomers; and the generation of the ylide proceeds via the formation of the IP form. Additionally, the calculated ΔG° values allow to calculate all the equilibrium constants, including the pK(C2) for the thiazolium C2 atom whose ionization is believed to initiate the catalytic cycle.

Thermodynamic Factors Affecting UC_1-xN_xIrradiation and Synthesis

Energy Technology Data Exchange (ETDEWEB)

Lindemer, T.B.

2005-04-22

There is interest in attempting to synthesize nearly pure uranium nitride (UN) kernels for high-temperature gas-cooled reactor (HTGR) fuel. Because the proposed process involves carbothermic conversion of a urania-carbon mixture in nitrogen and because there is a complete ideal solution of uranium carbide (UC) and UN, which is written as UC{sub 1-x}N{sub x}, the practical value of x for fuel irradiation needs to be determined. Insight is to be gained by relevant thermodynamic calculations of carbide-nitride equilibria for the fuel and fission product systems. The equilibria are readily compared on the nitrogen-based Ellingham diagram, which, in turn, provides guidance in interpreting past irradiations and in synthesis of the UC{sub 1-x}N{sub x} kernels.

Flexural strength of proof-tested and neutron-irradiated silicon carbide

Science.gov (United States)

Price, R. J.; Hopkins, G. R.

1982-08-01

Proof testing before service is a valuable method for ensuring the reliability of ceramic structures. Silicon carbide has been proposed as a very low activation first-wall and blanket structural material for fusion devices, where it would experience a high flux of fast neutrons. Strips of three types of silicon carbide were loaded in four-point bending to a stress sufficient to break about a third of the specimens. Groups of 16 survivors were irradiated to 2 × 10 26n/ m2 ( E>0.05 MeV) at 740°C and bend tested to failure. The strength distribution of chemically vapor-deposited silicon carbide (Texas Instruments) was virtually unchanged by irradiation. The mean strength of sintered silicon carbide (Carborundum Alpha) was reduced 34% by irradiation, while the Weibull modulus and the truncated strength distribution characteristic of proof-tested material were retained. Irradiation reduced the mean strength of reaction-bonded silicon carbide (Norton NC-430) by 58%, and the spread in strength values was increased. We conclude that for the chemically vapor-deposited and the sintered silicon carbide the benefits of proof testing to eliminate low strength material are retained after high neutron exposures.

Laser deposition of carbide-reinforced coatings

International Nuclear Information System (INIS)

Cerri, W.; Martinella, R.; Mor, G.P.; Bianchi, P.; D'Angelo, D.

1991-01-01

CO 2 laser cladding with blown powder presents many advantages: fusion bonding with the substrate with low dilution, metallurgical continuity in the metallic matrix, high solidification rates, ease of automation, and reduced environmental contamination. In the present paper, laser cladding experimental results using families of carbides (tungsten and titanium) mixed with metallic alloys are reported. As substrates, low alloy construction steel (AISI 4140) (austenitic stainless steel) samples have been utilized, depending on the particular carbide reinforcement application. The coating layers obtained have been characterized by metallurgical examination. They show low dilution, absence of cracks, and high abrasion resistance. The WC samples, obtained with different carbide sizes and percentages, have been characterized with dry and rubber wheel abrasion tests and the specimen behaviour has been compared with the behaviour of materials used for similar applications. The abrasion resistance proved to be better than that of other widely used hardfacing materials and the powder morphology have a non-negligible influence on the tribological properties. (orig.)

Atom-vacancy ordering and magnetic susceptibility of nonstoichiometric hafnium carbide

International Nuclear Information System (INIS)

Gusev, A.I.; Zyryanova, A.N.

1999-01-01

Experimental results on magnetic susceptibility of nonstoichiometric hafnium carbide HfC y (0.6 0.71 , HfC 0.78 and HfC 0.83 in the range of 870-930 K the anomalies are revealed which are associated with superstructure short-range ordering in a non-metallics sublattice. It is shown that a short-range order in HfC 0.71 and HfC 0.78 carbides corresponds to Hf 3 C 2 ordered phase, and in HfC 0.83 carbide - to Hf 6 C 5 ordered phase. HfC 0.78 carbide is found to possesses zero magnetic susceptibility in temperature range 910-980 K [ru

A Josephson ternary associative memory cell

International Nuclear Information System (INIS)

Morisue, M.; Suzuki, K.

1989-01-01

This paper describes a three-valued content addressable memory cell using a Josephson complementary ternary logic circuit named as JCTL. The memory cell proposed here can perform three operations of searching, writing and reading in ternary logic system. The principle of the memory circuit is illustrated in detail by using the threshold-characteristics of the JCTL. In order to investigate how a high performance operation can be achieved, computer simulations have been made. Simulation results show that the cycle time of memory operation is 120psec, power consumption is about 0.5 μW/cell and tolerances of writing and reading operation are +-15% and +-24%, respectively

MC Carbide Characterization in High Refractory Content Powder-Processed Ni-Based Superalloys

Science.gov (United States)

Antonov, Stoichko; Chen, Wei; Huo, Jiajie; Feng, Qiang; Isheim, Dieter; Seidman, David N.; Sun, Eugene; Tin, Sammy

2018-04-01

Carbide precipitates in Ni-based superalloys are considered to be desirable phases that can contribute to improving high-temperature properties as well as aid in microstructural refinement of the material; however, they can also serve as crack initiation sites during fatigue. To date, most of the knowledge pertaining to carbide formation has originated from assessments of cast and wrought Ni-based superalloys. As powder-processed Ni-based superalloys are becoming increasingly widespread, understanding the different mechanisms by which they form becomes increasingly important. Detailed characterization of MC carbides present in two experimental high Nb-content powder-processed Ni-based superalloys revealed that Hf additions affect the resultant carbide morphologies. This morphology difference was attributed to a higher magnitude of elastic strain energy along the interface associated with Hf being soluble in the MC carbide lattice. The composition of the MC carbides was studied through atom probe tomography and consisted of a complex carbonitride core, which was rich in Nb and with slight Hf segregation, surrounded by an Nb carbide shell. The characterization results of the segregation behavior of Hf in the MC carbides and the subsequent influence on their morphology were compared to density functional theory calculations and found to be in good agreement, suggesting that computational modeling can successfully be used to tailor carbide features.

Kinetic description of linear theta-pinch equilibria

International Nuclear Information System (INIS)

Batchelor, D.B.; Davidson, R.C.

1975-01-01

Equilibrium properties of linear theta-pinch plasmas are studied within the framework of the steady-state (o/x=0) Vlasov-Maxwell equations. The analysis is carried out for an infinitely long plasma column aligned parallel to an externally applied axial magnetic field Bsub(z)sup(ext)esub(z). Equilibrium properties are calculated for the class of rigid-rotor Vlasov equilibria, in which the th component distribution function (Hsub(perpendicular), Psub(theta), upsilonsub(z) depends on perpendicular energy H and canonical angular momentum Psub(theta), exclusively through the linear combination Hsub(perpendicular)-ωsub(j)Psub(theta), where ω;=const.=angular velocity of mean rotation. General equilibrium relations that pertain to the entire class of rigid-rotor Vlasov equilibria are discussed; and specific examples of sharp- and diffuse-boundary equilibrium configurations are considered. Rigid-rotor density and magnetic field profiles are compared with experimentally observed profiles. A general prescription is given for determining the functional dependence of the equilibrium distribution function on Hsub(perpendicular)-ωsub(j)Psub(theta) in circumstances, where the density profile or magnetic field profile is specified. (author)

Advanced technologies of production of cemented carbides and composite materials based on them

International Nuclear Information System (INIS)

Bondarenko, V.; Pavlotskaya, E.; Martynova, L.; Epik, I.

2001-01-01

The paper presents new technological processes of production of W, WC and (Ti, W)C powders, cemented carbides having a controlled carbon content, high-strength nonmagnetic nickel-bonded cemented carbides, cemented carbide-based composites having a wear-resistant antifriction working layer as well as processes of regeneration of cemented carbide waste. It is shown that these technological processes permit radical changes in the production of carbide powders and products of VK, TK, VN and KKhN cemented carbides. The processes of cemented carbide production become ecologically acceptable and free of carbon black, the use of cumbersome mixers is excluded, the power expenditure is reduced and the efficiency of labor increases. It becomes possible to control precisely the carbon content within a two-phase region -carbide-metal. A high wear resistance of parts of friction couples which are lubricated with water, benzine, kerosene, diesel fuel and other low-viscosity liquids, is ensured with increased strength and shock resistance. (author)

Diamond dispersed cemented carbide produced without using ultra high pressure equipment

International Nuclear Information System (INIS)

Moriguchi, H.; Tsuzuki, K.; Ikegaya, A.

2001-01-01

We have developed a composite material of dispersed diamond particles in cemented carbide without using ultra high pressure equipment. The developed diamond dispersed cemented carbide combines the excellent properties of cemented carbide with diamond and also provides 1.5 times improved fracture toughness over that of cemented carbide. They also show 10 times higher wear resistance over that of cemented carbide in a wear resistance test against bearing steel, and 5 times greater grindability than diamond compacts. Because ultra high pressure equipment is not used to produce the developed material, large compacts over 100 mm in diameter can be manufactured. The developed material showed 10-25 times higher wear resistance in real use as wear-resistant tools such as centerless blades and work-rests. (author)

Fission product phases in irradiated carbide fuels

International Nuclear Information System (INIS)

Ewart, F.T.; Sharpe, B.M.; Taylor, R.G.

1975-09-01

Oxide fuels have been widely adopted as 'first charge' fuels for demonstration fast reactors. However, because of the improved breeding characteristics, carbides are being investigated in a number of laboratories as possible advanced fuels. Irradiation experiments on uranium and mixed uranium-plutonium carbides have been widely reported but the instances where segregate phases have been found and subjected to electron probe analysis are relatively few. Several observations of such segregate phases have now been made over a period of time and these are collected together in this document. Some seven fuel pins have been examined. Two of the irradiations were in thermal materials testing reactors (MTR); the remainder were experimental assemblies of carbide gas bonded oxycarbide and sodium bonded oxycarbide in the Dounreay Fast Reactor (DFR). All fuel pins completed their irradiation without failure. (author)

INTERVAL-VALUED INTUITIONISTIC FUZZY BI-IDEALS IN TERNARY SEMIRINGS

Directory of Open Access Journals (Sweden)

D. KRISHNASWAMY

2016-04-01

Full Text Available In this paper we introduce the notions of interval-valued fuzzy bi-ideal, interval-valued anti fuzzy bi-ideal and interval-valued intuitionistic fuzzy bi-ideal in ternary semirings and some of the basic properties of these ideals are investigated. We also introduce normal interval-valued intuitionistic fuzzy ideals in ternary semirings.

Effect of temperature on acid-base equilibria in separation techniques. A review.

Science.gov (United States)

Gagliardi, Leonardo G; Tascon, Marcos; Castells, Cecilia B

2015-08-19

Studies on the theoretical principles of acid-base equilibria are reviewed and the influence of temperature on secondary chemical equilibria within the context of separation techniques, in water and also in aqueous-organic solvent mixtures, is discussed. In order to define the relationships between the retention in liquid chromatography or the migration velocity in capillary electrophoresis and temperature, the main properties of acid-base equilibria have to be taken into account for both, the analytes and the conjugate pairs chosen to control the solution pH. The focus of this review is based on liquid-liquid extraction (LLE), liquid chromatography (LC) and capillary electrophoresis (CE), with emphasis on the use of temperature as a useful variable to modify selectivity on a predictable basis. Simplified models were evaluated to achieve practical optimizations involving pH and temperature (in LLE and CE) as well as solvent composition in reversed-phase LC. Copyright © 2015 Elsevier B.V. All rights reserved.

First-principles study of ternary fcc solution phases from special quasirandom structures

International Nuclear Information System (INIS)

Shin Dongwon; Wang Yi; Liu Zikui; Walle, Axel van de

2007-01-01

In the present work, ternary special quasirandom structures (SQSs) for a fcc solid solution phase are generated at different compositions, x A =x B =x C =(1/3) and x A =(1/2), x B =x C =(1/4), whose correlation functions are satisfactorily close to those of a random fcc solution. The generated SQSs are used to calculate the mixing enthalpy of the fcc phase in the Ca-Sr-Yb system. It is observed that first-principles calculations of all the binary and ternary SQSs in the Ca-Sr-Yb system exhibit very small local relaxation. It is concluded that the fcc ternary SQSs can provide valuable information about the mixing behavior of the fcc ternary solid solution phase. The SQSs presented in this work can be widely used to study the behavior of ternary fcc solid solutions

Present status of uranium-plutonium mixed carbide fuel development for LMFBRs

International Nuclear Information System (INIS)

Handa, Muneo; Suzuki, Yasufumi

1984-01-01

The feature of carbide fuel is that it has the doubling time as short as about 13 years, that is, close to one half as compared with oxide fuel. The development of the carbide fuel in the past 10 years has been started in amazement. Especially in the program of new fuel development in USA started in 1974, He and Na bond fuel attained the burnup of 16 a/o without causing the breaking of cladding tubes. In 1984, the irradiation of the assembly composed of 91 fuel pins in the FFTF is expected. On the other hand in Japan, the fuel research laboratory was constructed in 1974 in the Oarai Laboratory, Japan Atomic Energy Research Institute, to carry out the studies on carbide fuel. In the autumn of 1982, two carbide fuel pins with different chemical composition have been successfully made. Accordingly, the recent status of the development is explained. The uranium-plutonium mixed carbide fuel is suitable to liquid metal-cooled fast breeder reactors because of large heat conductivity and the high density of nuclear fission substances. The thermal and nuclear characteristics of carbide fuel, the features of the reactor core using carbide fuel, the chemical and mechanical interaction of fuel and cladding tubes, the selection of bond materials, the manufacturing techniques for the fuel, the development of the analysis code for fuel behavior, and the research and development of carbide fuel in Japan are described. (Kako, I.)

The partially alternating ternary sum in an associative dialgebra

International Nuclear Information System (INIS)

Bremner, Murray R; Sanchez-Ortega, Juana

2010-01-01

The alternating ternary sum in an associative algebra, abc - acb - bac + bca + cab - cba, gives rise to the partially alternating ternary sum in an associative dialgebra with products dashv and vdash by making the argument a the center of each term. We use computer algebra to determine the polynomial identities in degree ≤9 satisfied by this new trilinear operation. In degrees 3 and 5, these identities define a new variety of partially alternating ternary algebras. We show that there is a 49-dimensional space of multilinear identities in degree 7, and we find equivalent nonlinear identities. We use the representation theory of the symmetric group to show that there are no new identities in degree 9.

stabilization of ikpayongo laterite with cement and calcium carbide

African Journals Online (AJOL)

PROF EKWUEME

Laterite obtained from Ikpayongo was stabilized with 2-10 % cement and 2-10 % Calcium Carbide waste, for use .... or open dumping which have effect on surface and ... Table 1: Chemical Composition of Calcium Carbide Waste and Cement.

Computation of tokamak equilibria with steady flow

International Nuclear Information System (INIS)

Kerner, W.; Tokuda, Shinji

1987-08-01

The equations for ideal MHD equilibria with stationary flow are reexamined and addressed as numerically applied to tokamak configurations with a free plasma boundary. Both the isothermal (purely toroidal flow) and the poloidal flow cases are treated. Experiment-relevant states with steady flow (so far only in the toroidal direction) are computed by the modified SELENE40 code. (author)

MHD stability of vertically asymmetric tokamak equilibria

International Nuclear Information System (INIS)

Dalhed, H.E.; Grimm, R.C.; Johnson, J.L.

1981-03-01

The ideal MHD stability properties of a special class of vertically asymmetric tokamak equilibria are examined. The calculations confirm that no major new physical effects are introduced and the modifications can be understood by conventional arguments. The results indicate that significant departures from up-down symmetry can be tolerated before the reduction in β becomes important for reactor operation

Predicting phase equilibria in one-component systems

Science.gov (United States)

Korchuganova, M. R.; Esina, Z. N.

2015-07-01

It is shown that Simon equation coefficients for n-alkanes and n-alcohols can be modeled using critical and triple point parameters. Predictions of the phase liquid-vapor, solid-vapor, and liquid-solid equilibria in one-component systems are based on the Clausius-Clapeyron relation, Van der Waals and Simon equations, and the principle of thermodynamic similarity.

Polarographic and potentiometric studies on some binary and ternary complex systems of dioxouranium(VI)

International Nuclear Information System (INIS)

Janarthanam, M.; Sivasankar, B.; Rengaraj, K.; Nair, M.S.

1995-01-01

The relative coordinating abilities of donor sites in the potentially tridentate ligands viz., asparagine, glutamine, aspartic acid and glutamic acid towards uranyl ion have been investigated by polarographic and pH-metric techniques. The metal ion forms 1:2 complexes under polarographic conditions. However, only 1:1 complex is observed under pH-metric conditions, where 1:2 complexes do not proceed due to extensive hydrolysis of the metal ion. The relative variations of ΔE 1/2 with pH and ligand concentration supported by conductometric titration data indicate that the primary amino groups in the amino acids are not involved in coordination with uranyl ion. Further, the amide groups in asparagine and glutamine also do not participate in coordination thus rendering these ligands unidentate. In aspartic and glutamic acid complexes, seven- and eight- membered chelate rings are formed involving two terminal carboxyl groups. The mixed ligand complex equilibria of uranyl ion involving aspartic acid/glutamic acid as primary ligands (A) and maleic acid, malonic acid, succinic acid and lactic acid as secondary ligands (B) have also been studied by computer based numerical evaluation of pH titration data. The concentration profiles have indicated the favorability of the formation of ternary complexes in general as reflected in the Δlog K values. (author). 10 refs., 1 fig., 1 tab

Phase equilibria of toluene/heptane with deep eutectic solvents based on ethyltriphenylphosphonium iodide for the potential use in the separation of aromatics from naphtha

International Nuclear Information System (INIS)

Kareem, Mukhtar A.; Mjalli, Farouq S.; Hashim, Mohd Ali; Hadj-Kali, Mohamed K.O.; Ghareh Bagh, Fatemeh Saadat; Alnashef, Inas M.

2013-01-01

Highlights: • Ionic liquid analogues are introduced as potential replacements for ionic liquids. • Deep eutectic solvents presented in this work were successful for extracting aromatics. • Hand correlation was applied to ascertain the experimental measurements. • The NRTL thermodynamic model was capable for correlating the LLE experimental data. -- Abstract: In this work, the liquid–liquid extraction of toluene from hydrocarbons mixtures (toluene/heptane) was investigated using deep eutectic solvents as solvents. Ethyltriphenylphosphonium iodide as a salt with either ethylene glycol or sulfolane as hydrogen-bond donors (HBDs) were utilized for synthesizing six DESs. (Liquid + liquid) equilibria data were determined experimentally for the ternary system (toluene + heptane + DES) at (30, 40, 50, and 60) °C and atmospheric pressure. Hand correlation was applied to establish the reliability of the experimental data. In many cases the correlation factor is found close to unity which indicates high reliability of the data. The selectivities and distribution coefficients were used to determine the suitability of these DESs as solvents for this extraction process. Higher selectivities than those published for sulfolane as a commercial solvent were observed. The DES made from ethyltriphenylphosphonium iodide and sulfolane at salt:HBD of 1:4 showed the best separation capability at 30 °C. Thus, it was further characterized by measuring its viscosity and refractive index at a range of temperatures to help understand its physical behaviour needed for process design. The non-random two-liquid (NRTL) model was applied successfully to correlate the experimental tie-lines and to calculate the phase compositions of the ternary systems. It has been found that the third non-randomness parameter varies linearly with the HBD number of moles

α-ternary decay of Cf isotopes, statistical model

International Nuclear Information System (INIS)

Joseph, Jayesh George; Santhosh, K.P.

2017-01-01

The process of splitting a heavier nucleus to three simultaneous fragments is termed as ternary fission and compared to usual binary fission, it is a rare process. Depending on the nature of third particle either it is called light charged particle (LCP) accompanying fission if it is light or true ternary fission if all three fragments have nearly same mass distributions. After experimental observations in early seventies, initially with a slow pace, now theoretical studies in ternary fission has turned to a hot topic in nuclear decay studies especially in past one decade. Mean while various models have been developed, existing being modified and seeking for new with a hope that it can beam a little more light to the profound nature of nuclear interaction. In this study a statistical method, level density formulation, has been employed

Lagrangian relative equilibria for a gyrostat in the three-body problem: bifurcations and stability

Energy Technology Data Exchange (ETDEWEB)

Guirao, Juan L G; Vera, Juan A, E-mail: juan.garcia@upct.e, E-mail: juanantonio.vera@upct.e [Departamento de Matematica Aplicada y EstadIstica, Universidad Politecnica de Cartagena, Hospital de Marina, 30203 Cartagena, Region de Murcia (Spain)

2010-05-14

In this paper we consider the non-canonical Hamiltonian dynamics of a gyrostat in the frame of the three-body problem. Using geometric/mechanic methods we study the approximate dynamics of the truncated Legendre series representation of the potential of an arbitrary order. Working in the reduced problem, we study the existence of relative equilibria that we refer to as Lagrange type following the analogy with the standard techniques. We provide necessary and sufficient conditions for the linear stability of Lagrangian relative equilibria if the gyrostat morphology form is close to a sphere. Thus, we generalize the classical results on equilibria of the three-body problem and many results on them obtained by the classic approach for the case of rigid bodies.

Untitled

Indian Academy of Sciences (India)

Structure and superconductivity in ternary systems of compounds 299. Erra B2 structure do not have T. above 1:2 K (Ku and Meisner 1981); (iii) for. Ao.67Pt3B the T. are 1-6, 28 and 56K for A = Ca,Sr and Ba (Shelton 1978) and. (iv) AOs B, A = Th, T = 3 K; A = Y, T = 6K (Ku 1980). 3. Ternary carbides. Of the known ternary ...

Corrosion behavior of porous chromium carbide in supercritical water

International Nuclear Information System (INIS)

Dong Ziqiang; Chen Weixing; Zheng Wenyue; Guzonas, Dave

2012-01-01

Highlights: ► Corrosion behavior of porous Cr 3 C 2 in various SCW conditions was investigated. ► Cr 3 C 2 is stable in SCW at temperature below 420–430 °C. ► Cracks and disintegration were observed at elevated testing temperatures. ► Degradation of Cr 3 C 2 is related to the intermediate product CrOOH. - Abstract: The corrosion behavior of highly porous chromium carbide (Cr 3 C 2 ) prepared by a reactive sintering process was characterized at temperatures ranging from 375 °C to 625 °C in a supercritical water environment with a pressure of 25–30 MPa. The test results show that porous chromium carbide is stable in SCW environments at temperatures under 425 °C, above which disintegration occurred. The porous carbide was also tested under hydrothermal conditions of pressures between 12 MPa and 50 MPa at constant temperatures of 400 °C and 415 °C, respectively. The pressure showed little effect on the stability of chromium carbide in the tests at those temperatures. The mechanism of disintegration of chromium carbide in SCW environments is discussed.

Mixed Uranium/Refractory Metal Carbide Fuels for High Performance Nuclear Reactors

International Nuclear Information System (INIS)

Knight, Travis; Anghaie, Samim

2002-01-01

Single phase, solid-solution mixed uranium/refractory metal carbides have been proposed as an advanced nuclear fuel for advanced, high-performance reactors. Earlier studies of mixed carbides focused on uranium and either thorium or plutonium as a fuel for fast breeder reactors enabling shorter doubling owing to the greater fissile atom density. However, the mixed uranium/refractory carbides such as (U, Zr, Nb)C have a lower uranium densities but hold significant promise because of their ultra-high melting points (typically greater than 3700 K), improved material compatibility, and high thermal conductivity approaching that of the metal. Various compositions of (U, Zr, Nb)C were processed with 5% and 10% metal mole fraction of uranium. Stoichiometric samples were processed from the constituent carbide powders, while hypo-stoichiometric samples with carbon-to-metal (C/M) ratios of 0.92 were processed from uranium hydride, graphite, and constituent refractory carbide powders. Processing techniques of cold uniaxial pressing, dynamic magnetic compaction, sintering, and hot pressing were investigated to optimize the processing parameters necessary to produce high density (low porosity), single phase, solid-solution mixed carbide nuclear fuels for testing. This investigation was undertaken to evaluate and characterize the performance of these mixed uranium/refractory metal carbides for high performance, ultra-safe nuclear reactor applications. (authors)

Properties of cemented carbides alloyed by metal melt treatment

International Nuclear Information System (INIS)

Lisovsky, A.F.

2001-01-01

The paper presents the results of investigations into the influence of alloying elements introduced by metal melt treatment (MMT-process) on properties of WC-Co and WC-Ni cemented carbides. Transition metals of the IV - VIll groups (Ti, Zr, Ta, Cr, Re, Ni) and silicon were used as alloying elements. It is shown that the MMT-process allows cemented carbides to be produced whose physico-mechanical properties (bending strength, fracture toughness, total deformation, total work of deformation and fatigue fracture toughness) are superior to those of cemented carbides produced following a traditional powder metallurgy (PM) process. The main mechanism and peculiarities of the influence of alloying elements added by the MMT-process on properties of cemented carbides have been first established. The effect of alloying elements on structure and substructure of phases has been analyzed. (author)

Adiabatic pipelining: a key to ternary computing with quantum dots

Science.gov (United States)

Pečar, P.; Ramšak, A.; Zimic, N.; Mraz, M.; Lebar Bajec, I.

2008-12-01

The quantum-dot cellular automaton (QCA), a processing platform based on interacting quantum dots, was introduced by Lent in the mid-1990s. What followed was an exhilarating period with the development of the line, the functionally complete set of logic functions, as well as more complex processing structures, however all in the realm of binary logic. Regardless of these achievements, it has to be acknowledged that the use of binary logic is in computing systems mainly the end result of the technological limitations, which the designers had to cope with in the early days of their design. The first advancement of QCAs to multi-valued (ternary) processing was performed by Lebar Bajec et al, with the argument that processing platforms of the future should not disregard the clear advantages of multi-valued logic. Some of the elementary ternary QCAs, necessary for the construction of more complex processing entities, however, lead to a remarkable increase in size when compared to their binary counterparts. This somewhat negates the advantages gained by entering the ternary computing domain. As it turned out, even the binary QCA had its initial hiccups, which have been solved by the introduction of adiabatic switching and the application of adiabatic pipeline approaches. We present here a study that introduces adiabatic switching into the ternary QCA and employs the adiabatic pipeline approach to successfully solve the issues of elementary ternary QCAs. What is more, the ternary QCAs presented here are sizewise comparable to binary QCAs. This in our view might serve towards their faster adoption.

Adiabatic pipelining: a key to ternary computing with quantum dots

International Nuclear Information System (INIS)

Pecar, P; Zimic, N; Mraz, M; Lebar Bajec, I; Ramsak, A

2008-01-01

The quantum-dot cellular automaton (QCA), a processing platform based on interacting quantum dots, was introduced by Lent in the mid-1990s. What followed was an exhilarating period with the development of the line, the functionally complete set of logic functions, as well as more complex processing structures, however all in the realm of binary logic. Regardless of these achievements, it has to be acknowledged that the use of binary logic is in computing systems mainly the end result of the technological limitations, which the designers had to cope with in the early days of their design. The first advancement of QCAs to multi-valued (ternary) processing was performed by Lebar Bajec et al, with the argument that processing platforms of the future should not disregard the clear advantages of multi-valued logic. Some of the elementary ternary QCAs, necessary for the construction of more complex processing entities, however, lead to a remarkable increase in size when compared to their binary counterparts. This somewhat negates the advantages gained by entering the ternary computing domain. As it turned out, even the binary QCA had its initial hiccups, which have been solved by the introduction of adiabatic switching and the application of adiabatic pipeline approaches. We present here a study that introduces adiabatic switching into the ternary QCA and employs the adiabatic pipeline approach to successfully solve the issues of elementary ternary QCAs. What is more, the ternary QCAs presented here are sizewise comparable to binary QCAs. This in our view might serve towards their faster adoption.

Adiabatic pipelining: a key to ternary computing with quantum dots.

Science.gov (United States)

Pečar, P; Ramšak, A; Zimic, N; Mraz, M; Lebar Bajec, I

2008-12-10

The quantum-dot cellular automaton (QCA), a processing platform based on interacting quantum dots, was introduced by Lent in the mid-1990s. What followed was an exhilarating period with the development of the line, the functionally complete set of logic functions, as well as more complex processing structures, however all in the realm of binary logic. Regardless of these achievements, it has to be acknowledged that the use of binary logic is in computing systems mainly the end result of the technological limitations, which the designers had to cope with in the early days of their design. The first advancement of QCAs to multi-valued (ternary) processing was performed by Lebar Bajec et al, with the argument that processing platforms of the future should not disregard the clear advantages of multi-valued logic. Some of the elementary ternary QCAs, necessary for the construction of more complex processing entities, however, lead to a remarkable increase in size when compared to their binary counterparts. This somewhat negates the advantages gained by entering the ternary computing domain. As it turned out, even the binary QCA had its initial hiccups, which have been solved by the introduction of adiabatic switching and the application of adiabatic pipeline approaches. We present here a study that introduces adiabatic switching into the ternary QCA and employs the adiabatic pipeline approach to successfully solve the issues of elementary ternary QCAs. What is more, the ternary QCAs presented here are sizewise comparable to binary QCAs. This in our view might serve towards their faster adoption.

(Vapour + liquid) equilibria for (2,2-dimethoxypropane + methanol) and (2,2-dimethoxypropane + acetone)

International Nuclear Information System (INIS)

Jiang Hui; Li Haoran; Wang Congmin; Tan Taijun; Han Shijun

2003-01-01

The isothermal and isobaric (vapour + liquid) equilibria for (2,2-dimethoxypropane + methanol) and (2,2-dimethoxypropane + acetone) measured with an inclined ebulliometer are presented. The experimental results are analysed using the UNIQUAC equation with the temperature-dependent binary parameters with satisfactory results. Isobaric (vapour + liquid) equilibria data for these systems at p=99.99 kPa are compared with the literature data. Experimental vapour pressure of 2,2-dimethoxypropane are also included

Wetting and interface interactions in the B4C/Al-Me (Me=Cu, Sn) systems

International Nuclear Information System (INIS)

Aizenshtein, M.; Froumin, N.; Dariel, M.P.; Frage, N.

2008-01-01

The wettability of B 4 C in contact with non-carbide and non-boride forming liquid metals (such as Cu or Sn) has been the subject of several studies. These metals do not wet boron carbide unless a reactive element is added to the melt. The present study is concerned with the addition of Al which completes the series of reactive elements added to the non-wetting metals. While Si represents the elements that form stable carbides and Ti represents the elements that form stable borides, Al belongs to the group of elements that form ternary borocarbides. The wetting experiments in the B 4 C/(Me-Al, Me=Cu, Sn) systems have shown that a ternary product, namely Al 8 B 4 C 7 was formed at the interface and that wetting is governed by the thermodynamic properties of the binary liquid system

Medium temperature reaction between lanthanide and actinide carbides and hydrogen

International Nuclear Information System (INIS)

Dean, G.; Lorenzelli, R.; Pascard, R.

1964-01-01

Hydrogen is fixed reversibly by the lanthanide and actinide mono carbides in the range 25 - 400 C, as for pure corresponding metals. Hydrogen goes into the carbides lattice through carbon vacancies and the total fixed amount is approximately equal to two hydrogen atoms per initial vacancy. Final products c.n thus be considered as carbo-hydrides of general formula M(C 1-x , H 2x ). The primitive CFC, NaCl type, structure remains unchanged but expands strongly in the case of actinide carbides. With lanthanide carbides, hydrogenation induces a phase transformation with reappearance of the metal structure (HCP). Hydrogen decomposition pressures of all the studied carbo-hydrides are greater than those of the corresponding di-hydrides. (authors) [fr

On the carbide formation in high-carbon stainless steel

International Nuclear Information System (INIS)

Mujahid, M.; Qureshi, M.I.

1996-01-01

Stainless steels containing high Cr as well as carbon contents in excess of 1.5 weight percent have been developed for applications which require high resistance erosion and environmental corrosion. Formation of carbides is one of important parameters for controlling properties of these materials especially erosion characteristics. Percent work includes the study of different type of carbides which from during the heat treatment of these materials. It has been found that precipitation of secondary carbides and the nature of matrix transformation plays an important role in determining the hardness characteristics of these materials. (author)

Ternary fission of spontaneously fissile uranium isomers excited by neutrons

International Nuclear Information System (INIS)

Makarenko, V.E.; Molchanov, Y.D.; Otroshchenko, G.A.; Yan'kov, G.B.

1989-01-01

Spontaneously fissile isomers (SFI) of uranium were excited in the reactions 236,238 U(n,n') at an average neutron energy 4.5 MeV. A pulsed electrostatic accelerator and time analysis of the fission events were used. Fission fragments were detected by the scintillation method, and long-range particles from fission were detected by an ionization method. The relative probability of fission of nuclei through a spontaneously fissile isomeric state was measured: (1.30±0.01)·10 -4 ( 236 U) and (1.48±0.02)·10 -4 ( 238 U). Half-lives of the isomers were determined: 121±2 nsec (the SFI 236 U) and 267±13 nsec (the SFI 238 U). In study of the ternary fission of spontaneously fissile isotopes of uranium it was established that the probability of the process amounts to one ternary fission per 163±44 binary fissions of the SFI 236 U and one ternary fission per 49±14 binary fissions of the SFI 238 U. The substantial increase of the probability of ternary fission of SFI of uranium in comparison with the case of ternary fission of nuclei which are not in an isomeric state may be related to a special nucleon configuration of the fissile isomers of uranium

Sintering of nano crystalline α silicon carbide by doping with boron ...

Indian Academy of Sciences (India)

Sinterable nano silicon carbide powders of mean particle size (37 nm) were prepared by attrition milling and chemical processing of an acheson type alpha silicon carbide having mean particle size of 0.39 m (390 nm). Pressureless sintering of these powders was achieved by addition of boron carbide of 0.5 wt% together ...

Experimental determination and modeling of the solubility phase diagram of the ternary system (Li{sub 2}SO{sub 4} + K{sub 2}SO{sub 4} + H{sub 2}O) at 288.15 K

Energy Technology Data Exchange (ETDEWEB)

Wang, Shiqiang, E-mail: wangshiqiang@tust.edu.cn [Tianjin Key Laboratory of Marine Resources and Chemistry, College of Marine Science and Engineering, Tianjin University of Science and Technology, Tianjin 300457 (China); Guo, Yafei [Tianjin Key Laboratory of Marine Resources and Chemistry, College of Marine Science and Engineering, Tianjin University of Science and Technology, Tianjin 300457 (China); Li, Dongchan [Engineering Research Center of Seawater Utilization Technology of Ministry of Education, Hebei University of Technology, Tianjin 300130 (China); Tang, Peng; Deng, Tianlong [Tianjin Key Laboratory of Marine Resources and Chemistry, College of Marine Science and Engineering, Tianjin University of Science and Technology, Tianjin 300457 (China)

2015-02-10

Highlights: • Solubility of the ternary system Li{sub 2}SO{sub 4} + K{sub 2}SO{sub 4} + H{sub 2}O at 288.15 K has been measured. • Phase diagram of this system was simulated and calculated by a thermodynamic model. • Li{sub 2}SO{sub 4}·K{sub 2}SO{sub 4} belongs to the incongruent double salt in this system. • Solution density was calculated using empirical equation. - Abstract: The solubility and density in the thermodynamic phase equilibria ternary system (Li{sub 2}SO{sub 4} + K{sub 2}SO{sub 4} + H{sub 2}O) at 288.15 K and 0.1 MPa were investigated experimentally with the method of isothermal dissolution equilibrium. This system at 288.15 K consists of two invariant points, three univariant isothermal dissolution curves; and three crystallization regions. The salt Li{sub 2}SO{sub 4}·K{sub 2}SO{sub 4} belongs to the incongruent double salt, and no solid solution was found. Based on the Pitzer model and its extended Harvie–Weare (HW) model, the mixing ion-interaction parameters of θ{sub Li,K}, ψ{sub Li,K,SO4} at 288.15 K and the solubility equilibrium constants K{sub sp} of solid phases Li{sub 2}SO{sub 4}·H{sub 2}O and Li{sub 2}SO{sub 4}·K{sub 2}SO{sub 4}, which are not reported in the literature were acquired. A comparison between the calculated and experimental results at 288.15 K for the ternary system shows that the calculated solubilities obtained with the extended HW model agree well with experimental data.

(Solid + liquid) isothermal evaporation phase equilibria in the aqueous ternary system (Li{sub 2}SO{sub 4} + MgSO{sub 4} + H{sub 2}O) at T = 308.15 K

Energy Technology Data Exchange (ETDEWEB)

Wang Shiqiang [Qinghai Institute of Salt Lakes, Chinese Academy of Sciences, Xining 810008 (China); Graduate University of Chinese Academy of Sciences, Beijing 100039 (China); Deng Tianlong [Qinghai Institute of Salt Lakes, Chinese Academy of Sciences, Xining 810008 (China); College of Materials, Chemistry and Chemical Engineering, Chengdu University Technology, Chengdu 610059 (China)], E-mail: dtl@cdut.edu.cn

2008-06-15

The solubility and the density in the aqueous ternary system (Li{sub 2}SO{sub 4} + MgSO{sub 4} + H{sub 2}O) at T = 308.15 K were determined by the isothermal evaporation. Our experimental results permitted the construction of the phase diagram and the plot of density against composition. It was found that there is one eutectic point for (Li{sub 2}SO{sub 4} . H{sub 2}O + MgSO{sub 4} . 7H{sub 2}O), two univariant curves, and two crystallization regions corresponding to lithium sulphate monohydrate (Li{sub 2}SO{sub 4} . H{sub 2}O) and epsomite (MgSO{sub 4} . 7H{sub 2}O). The system belongs to a simple co-saturated type, and neither double salts nor solid solution was found. Based on the Pitzer ion-interaction model and its extended HW models of aqueous electrolyte solution, the solubility of the ternary system at T = 308.15 K has been calculated. The predicted solubility agrees well with the experimental values.

Recovery of pure slaked lime from carbide sludge: Case study of ...

African Journals Online (AJOL)

Adaobi

Carbide sludge is the by-product of reaction between calcium carbide and water in the production of ... soluble in water. The optimum percentage yield was 78.2% at a ratio of 1:1000(w/v) of sludge to water held for 24 h at room temperature. Key words: Carbide, recovery, ..... calcium carbonate and other calcium products.

Evaluation of titanium carbide metal matrix composites deposited via laser cladding

Science.gov (United States)

Cavanaugh, Daniel Thomas

Metal matrix composites have been widely studied in terms of abrasion resistance, but a particular material system may behave differently as particle size, morphology, composition, and distribution of the hardening phase varies. The purpose of this thesis was to understand the mechanical and microstructural effects of combining titanium carbide with 431 series stainless steel to create a unique composite via laser cladding, particularly regarding wear properties. The most predominant effect in increasing abrasion resistance, measured via ASTM G65, was confirmed to be volume fraction of titanium carbide addition. Macrohardness was directly proportional to the amount of carbide, though there was an overall reduction in individual particle microhardness after cladding. The reduction in particle hardness was obscured by the effect of volume fraction carbide and did not substantially contribute to the wear resistance changes. A model evaluating effective mean free path of the titanium carbide particles was created and correlated to the measured data. The model proved successful in linking theoretical mean free path to overall abrasion resistance. The effects of the titanium carbide particle distributions were limited, while differences in particle size were noticeable. The mean free path model did not correlate well with the particle size, but it was shown that the fine carbides were completely removed by the coarse abrasive particles in the ASTM G65 test. The particle morphology showed indications of influencing the wear mode, but no statistical reduction was observed in the volume loss figures. Future studies may more specifically focus on particle morphology or compositional effects of the carbide particles.

Thermodynamic analysis of thermal plasma process of composite zirconium carbide and silicon carbide production from zircon concentrates

International Nuclear Information System (INIS)

Kostic, Z.G.; Stefanovic, P.Lj.; Pavlovic; Pavlovic, Z.N.; Zivkovic, N.V.

2000-01-01

Improved zirconium ceramics and composites have been invented in an effort to obtain better resistance to ablation at high temperature. These ceramics are suitable for use as thermal protection materials on the exterior surfaces of spacecraft, and in laboratory and industrial environments that include flows of hot oxidizing gases. Results of thermodynamic consideration of the process for composite zirconium carbide and silicon carbide ultrafine powder production from ZrSiO 4 in argon thermal plasma and propane-butane gas as reactive quenching reagents are presented in the paper. (author)

A simple urea-based route to ternary metal oxynitride nanoparticles

International Nuclear Information System (INIS)

Gomathi, A.; Reshma, S.; Rao, C.N.R.

2009-01-01

Ternary metal oxynitrides are generally prepared by heating the corresponding metal oxides with ammonia for long durations at high temperatures. In order to find a simple route that avoids use of gaseous ammonia, we have employed urea as the nitriding agent. In this method, ternary metal oxynitrides are obtained by heating the corresponding metal carbonates and transition metal oxides with excess urea. By this route, ternary metal oxynitrides of the formulae MTaO 2 N (M=Ca, Sr or Ba), MNbO 2 N (M=Sr or Ba), LaTiO 2 N and SrMoO 3-x N x have been prepared successfully. The oxynitrides so obtained were generally in the form of nanoparticles, and were characterized by various physical techniques. - Graphical abstract: Nanoparticles of ternary metal oxynitrides can be synthesized by means of urea route. Given is the TEM image of the nanoparticles of CaTaO 2 N so obtained and the insets show the SAED pattern and HREM image of the nanoparticles

Model for competitive binary and ternary ion-molecule reactions

International Nuclear Information System (INIS)

Herbst, E.

1985-01-01

A mechanism by which competitive binary and ternary ion-molecule reactions can occur is proposed. Calculations are undertaken for the specific system CH3(+) + NH3 + He which has been studied in the laboratory by Smith and Adams (1978), and the potential surface of which has been studied theoretically by Nobes and Radom (1983). It is shown that a potential-energy barrier in the exit channel prevents the rapid dissociation of collision complexes with large amounts of angular momentum and thereby allows collisional stabilization of the complexes. The calculated ternary-reaction rate coefficient is in good agreement with the experimental value, but a plot of the effective two-body rate coefficient of the ternary channel vs helium density does not quite show the observed saturation. 21 references

From Singularity Theory to Finiteness of Walrasian Equilibria

DEFF Research Database (Denmark)

Castro, Sofia B.S.D.; Dakhlia, Sami F.; Gothen, Peter

The paper establishes that for an open and dense subset of smooth exchange economies, the number of Walrasian equilibria is finite. In particular, our results extend to non-regular economies; it even holds when restricted to the subset of critical ones. The proof rests on concepts from singularity...... theory....

Formation and characterization of zein-propylene glycol alginate-surfactant ternary complexes: Effect of surfactant type.

Science.gov (United States)

Dai, Lei; Sun, Cuixia; Wei, Yang; Zhan, Xinyu; Mao, Like; Gao, Yanxiang

2018-08-30

In this study, zein, propylene glycol alginate (PGA) and surfactant ternary complexes were fabricated by antisolvent co-precipitation method. Two types of surfactants (rhamnolipid and lecithin) were applied to generate zein-PGA-rhamnolipid (Z-P-R) and zein-PGA-lecithin (Z-P-L) ternary complexes, respectively. Results showed that the surfactant types significantly affected the properties of ternary complexes. The formation of ternary complexes was mainly due to the non-covalent interactions such as hydrogen bonding, electrostatic interaction and hydrophobic interactions among zein, PGA and surfactants. Moreover, the thermal stability of ternary complexes was enhanced with increasing the levels of both surfactants. Notably, ternary complex dispersions exhibited better stability against pH from 2 to 8. Furthermore, a compact network structure was observed in Z-P-R ternary complex, while Z-P-L ternary complex remained the spherical structure. These findings would provide new insights into the development of novel delivery system and expand the options, when zein-based complexes were utilized under different environment conditions. Copyright © 2018 Elsevier Ltd. All rights reserved.

Dilatometry Analysis of Dissolution of Cr-Rich Carbides in Martensitic Stainless Steels

Science.gov (United States)

Huang, Qiuliang; Volkova, Olena; Biermann, Horst; Mola, Javad

2017-12-01

The dissolution of Cr-rich carbides formed in the martensitic constituent of a 13 pct Cr stainless steel was studied by dilatometry and correlative electron channeling contrast examinations. The dissolution of carbides subsequent to the martensite reversion to austenite was associated with a net volume expansion which in turn increased the dilatometry-based apparent coefficient of thermal expansion (CTEa) during continuous heating. The effects of carbides fraction and size on the CTEa variations during carbides dissolution are discussed.

Carbide-reinforced metal matrix composite by direct metal deposition

Science.gov (United States)

Novichenko, D.; Thivillon, L.; Bertrand, Ph.; Smurov, I.

Direct metal deposition (DMD) is an automated 3D laser cladding technology with co-axial powder injection for industrial applications. The actual objective is to demonstrate the possibility to produce metal matrix composite objects in a single-step process. Powders of Fe-based alloy (16NCD13) and titanium carbide (TiC) are premixed before cladding. Volume content of the carbide-reinforced phase is varied. Relationships between the main laser cladding parameters and the geometry of the built-up objects (single track, 2D coating) are discussed. On the base of parametric study, a laser cladding process map for the deposition of individual tracks was established. Microstructure and composition of the laser-fabricated metal matrix composite objects are examined. Two different types of structures: (a) with the presence of undissolved and (b) precipitated titanium carbides are observed. Mechanism of formation of diverse precipitated titanium carbides is studied.

He and Be ternary spontaneous fission of sup 2 sup 5 sup 2 Cf

CERN Document Server

Hwang, J K; Ramayya, A V; Hamilton, J H

2002-01-01

Ternary and binary fission studies of sup 2 sup 5 sup 2 Cf have been carried out by using the Gammasphere detector array with light charged particle (LCD) detectors. The relative sup 4 He and sup 5 He ternary fission yields were determined. The kinetic energies of the sup 5 He and sup 4 He ternary particles were found to be approximately 11 and 16 MeV, respectively. The sup 5 He particles contribute 10-20 % to the total observed alpha ternary yield. The data indicate that in nuclei with octupole deformations the population for the negative parity bands might be enhanced in the alpha ternary fission. >From LCP-gamma double gated spectra, neutron multiplicity distributions for alpha ternary fission pairs were measured. The average neutron multiplicity decreases about 0.7 AMU in going from the binary to alpha ternary fission in the approximately same mass splittings (104-146). From the analysis of the gamma-gamma matrix gated on the sup 1 sup 0 Be particles, the two fragment pairs of sup 1 sup 3 sup 8 Xe - sup 1...

Tricolore. A flexible color scale for ternary compositions

DEFF Research Database (Denmark)

2018-01-01

tricolore is an R library providing a flexible color scale for the visualization of three-part/ternary compositions. Its main functionality is to color-code any ternary composition as a mixture of three primary colours and to draw a suitable color-key. tricolore flexibly adapts to different...... visualisation challenges via - discrete and continuous color support - support for unbalanced compositional data via centering - support for data with very narrow range via scaling - hue, chroma and lightness options...

Calculation of ternary interdiffusion coefficients using a single diffusion couple

Czech Academy of Sciences Publication Activity Database

Čermák, Jiří; Rothová, Věra

2016-01-01

Roč. 54, č. 5 (2016), s. 305-314 ISSN 0023-432X R&D Projects: GA MŠk(CZ) ED1.1.00/02.0068 Institutional support: RVO:68081723 Keywords : diffusion * interdiffusion * ternary alloys * ternary diffusion coefficients Subject RIV: BJ - Thermodynamics Impact factor: 0.366, year: 2016

Crystallization, data collection and processing of the chymotrypsin–BTCI–trypsin ternary complex

Energy Technology Data Exchange (ETDEWEB)

Esteves, Gisele Ferreira; Teles, Rozeni Chagas Lima; Cavalcante, Nayara Silva; Neves, David; Ventura, Manuel Mateus [Laboratório de Biofísica, Instituto de Ciências Biológicas, Universidade de Brasília, 70910-900 Brasília-DF (Brazil); Barbosa, João Alexandre Ribeiro Gonçalves, E-mail: joao@lnls.br [Center for Structural Molecular Biology (CeBiME), Brazilian Synchrotron Light Laboratory (LNLS), CP 6192, 13083-970 Campinas-SP (Brazil); Freitas, Sonia Maria de, E-mail: joao@lnls.br [Laboratório de Biofísica, Instituto de Ciências Biológicas, Universidade de Brasília, 70910-900 Brasília-DF (Brazil)

2007-12-01

A ternary complex of the proteinase inhibitor (BTCI) with trypsin and chymotrypsin was crystallized and its crystal structure was solved by molecular replacement. A ternary complex of the black-eyed pea trypsin and chymotrypsin inhibitor (BTCI) with trypsin and chymotrypsin was crystallized by the sitting-drop vapour-diffusion method with 0.1 M HEPES pH 7.5, 10%(w/v) polyethylene glycol 6000 and 5%(v/v) 2-methyl-2,4-pentanediol as precipitant. BTCI is a small protein with 83 amino-acid residues isolated from Vigna unguiculata seeds and is able to inhibit trypsin and chymotrypsin simultaneously by forming a stable ternary complex. X-ray data were collected from a single crystal of the trypsin–BTCI–chymotrypsin ternary complex to 2.7 Å resolution under cryogenic conditions. The structure of the ternary complex was solved by molecular replacement using the crystal structures of the BTCI–trypsin binary complex (PDB code) and chymotrypsin (PDB code) as search models.

Crystallization, data collection and processing of the chymotrypsin–BTCI–trypsin ternary complex

International Nuclear Information System (INIS)

Esteves, Gisele Ferreira; Teles, Rozeni Chagas Lima; Cavalcante, Nayara Silva; Neves, David; Ventura, Manuel Mateus; Barbosa, João Alexandre Ribeiro Gonçalves; Freitas, Sonia Maria de

2007-01-01

A ternary complex of the proteinase inhibitor (BTCI) with trypsin and chymotrypsin was crystallized and its crystal structure was solved by molecular replacement. A ternary complex of the black-eyed pea trypsin and chymotrypsin inhibitor (BTCI) with trypsin and chymotrypsin was crystallized by the sitting-drop vapour-diffusion method with 0.1 M HEPES pH 7.5, 10%(w/v) polyethylene glycol 6000 and 5%(v/v) 2-methyl-2,4-pentanediol as precipitant. BTCI is a small protein with 83 amino-acid residues isolated from Vigna unguiculata seeds and is able to inhibit trypsin and chymotrypsin simultaneously by forming a stable ternary complex. X-ray data were collected from a single crystal of the trypsin–BTCI–chymotrypsin ternary complex to 2.7 Å resolution under cryogenic conditions. The structure of the ternary complex was solved by molecular replacement using the crystal structures of the BTCI–trypsin binary complex (PDB code) and chymotrypsin (PDB code) as search models

The preparation of titanium-vanadium carbide/nickel cermets. Technical report

International Nuclear Information System (INIS)

Precht, W.; Sprissler, B.

1976-01-01

Titanium/vanadium alloy carbide rods were prepared by a zone melting procedure. Wetting studies were carried out using sections of the fused rods and candidate matrix material. It was established that nickel exhibits excellent wetting of (Ti, V) C, and accordingly cermet blends were prepared and liquid phase sintered. Processing parameters are discussed as well as their effect on the final microstructure. Alternate methods for cermet preparation are offered which use as received titanium carbide and vanadium carbide powders

Carbide Transformation in Haynes 230 during Long-term Exposure at High Temperature

International Nuclear Information System (INIS)

Lee, Ho Jung; Kim, Hyunmyung; Hong, Sunghoon; Jang, Changheui

2014-01-01

Long-term aging behaviors of a solid solution hardened Ni-base superalloy, Haynes 230 at high temperature have not been fully investigated yet. In this study, long-term aging tests of Haynes 230 was carried out to evaluate microstructure changes especially in carbide evolution. In addition, its consequential effects on tensile property such as tensile strength and elongation were discussed. In Haynes 230, a nucleation of the secondary carbides was dominant at 800 .deg. C ageing while growth at 900 .deg. C ageing. In addition, after aging at 800 .deg. C, transition of primary W-rich M 6 C carbides (break down) were observed and it showed high W content (up to 70 at.% W) compared to un-aged W-rich M 6 C carbides (around 30 at.% W). Coarsened Cr- and Ni-rich phase surrounded by carbide depleted region and high W-rich M 6 C carbide along the grain boundary were formed only at 900 .deg. C after long-term exposure above 10000 h. Tensile strength of aged Haynes 230 increased at 800 .deg. C while decreased at 900 .deg. C due to the formation of secondary carbide within the grains at 800 .deg. C. Decrease in elongation would be resulted from the coarsened and continuous carbides at the grain boundary as well as Cr- and Ni-rich phase along the grain boundary

Microstructural evaluation of the NbC-20Ni cemented carbides during sintering

International Nuclear Information System (INIS)

Rodrigues, D.; Cannizza, E.

2016-01-01

Full text: Fine carbides in a metallic matrix (binder) form the microstructure of the cemented carbides. Grain size and binder content are the main variables to adjust hardness and toughness. These products are produced by Powder Metallurgy, and traditional route involves mixing carbides with binder by high energy milling, pressing and sintering. During sintering, a liquid phase promotes densification, and a final relative density higher than 99% is expected. Sintering is carried out at high temperatures, and dissolution of the carbides changes the chemical composition of the binder. To control grain growth of the main carbide, which reduces hardness, small quantities of secondary carbides are used. These additives limit dissolution and precipitation of the main carbides reducing the final grain size. This paper focused the structural and chemical evolution during sintering using NbC-20Ni cermets. Mixtures of very fine NbC carbides and carbonyl Ni powders were produce by intense milling. These mixtures were pressed using uniaxial pressures from 50 to 200MPa. Shrinkage was evaluated using dilatometric measurements under an atmosphere of dynamic argon. Samples were also sintered under vacuum in high temperature industrial furnace. The sintered samples were characterized in terms of density hardness, toughness and microstructure. DRX was the main tool used to evaluate the structural evolution of the binder. In situ chemical analysis helped to understand the dissolution mechanisms. (author)

stabilization of ikpayongo laterite with cement and calcium carbide

African Journals Online (AJOL)

PROF EKWUEME

the stabilization of soil will ensure economy in road construction, while providing an effective way of disposing calcium carbide waste. KEYWORDS: Cement, Calcium carbide waste, Stabilization, Ikpayongo laterite, Pavement material. INTRODUCTION. Road building in the developing nations has been a major challenge to ...

Close pairs of relative equilibria for identical point vortices

DEFF Research Database (Denmark)

Dirksen, Tobias; Aref, Hassan

2011-01-01

Numerical solution of the classical problem of relative equilibria for identical point vortices on the unbounded plane reveals configurations that are very close to the analytically known, centered, symmetrically arranged, nested equilateral triangles. New numerical solutions of this kind are fou...

Calculation of vapour pressures over mixed carbide fuels

International Nuclear Information System (INIS)

Joseph, M.; Mathews, C.K.

1988-01-01

Vapour pressure over the uranium-plutonium mixed carbide (Usub(l-p) Pusub(p C) was calculated in the temperature range of 1300-9000 for various compositions (p=0.1 to 0.7). Effects of variation of the sesquicarbide content were also studied. The principle of corresponding states was applied to UC and mixed carbides to obtain the equation of state. (author)

Analytical determination of distillation boundaries for ternary azeotropic systems

OpenAIRE

Marcilla Gomis, Antonio; Reyes Labarta, Juan Antonio; Velasco, Raúl; Serrano Cayuelas, María Dolores; Olaya López, María del Mar

2009-01-01

A new straight forward algorithm to calculate distillation boundaries in ternary azeotropic systems has been developed. The proposed method allows, using cubic splines, the calculation of distillation trajectories and the calculation of that corresponding to the searched distillation boundaries. The algorithm is applied to 4 ternary liquid-vapour systems to test its validity. Vicepresidency of Research (University of Alicante) and Generalitat Valenciana (GV/2007/125)

Effect on strength of ternary alloying additions in L12 intermetallics

International Nuclear Information System (INIS)

Wu Yuanpang.

1991-01-01

The thermodynamic properties of {111} antiphase boundaries (APBs) as well as the site preference of ternary additions in an A 3 B intermetallic with L1 2 structure are studied, using a thermodynamic model. A survey of the results from a variety of ternary alloying additions to Ni 3 Al has shown that there is a conflict in the actual role which solid solution strengthening plays in the athermal increment of yield strength. For instance, a good quantitative agreement with linear concentration law is observed only in alloys with stoichiometric compositions but not in the general case of non-stoichiometric alloys. In the light of the possibility that micro-segregation could explain the experimental discrepancy, the author extends the binary solid solution strengthening theory to the ternary system in an L1 2 structure for the four real systems of Ni-Al-Si, Ni-Al-Ti, Ni-Al-Hf, and Ni-Al-V. It is found that ternary site preference plays an important role in the ternary solid solution strengthening theory with L1 2 structure. Good quantitative agreement was found between the calculated and experimentally measured strength for both stoichiometric and nonstoichiometric alloys

Ternary complex formation of lanthanides and radiolanthanides with phosphate and serum proteins

International Nuclear Information System (INIS)

Neumaier, B.; Roesch, F.

1999-01-01

Radioyttrium was recently reported to form ternary complexes with phosphate and serum proteins in blood. In the present work it was investigated whether the trivalent radiolanthanides react in a chemically similar way. In systematic binding studies using gel filtration a ternary complex formation between different lanthanides, phosphate and serum proteins could be identified. The tendency to build a ternary compound of the type Ln III - phosphate - serum protein, however, is dependent on the ionic radii of the lanthanides. Whereas the light and transition lanthanides have a strong inclination to build a ternary complex, this tendency is weaker for the heavier ones. Taking into account the high content of phosphate in human blood, the corresponding ternary complexes of radiolanthanides represent an important transport form of these elements in blood. This finding may contribute to an understanding of the nuclear medical observation on the biodistribution of radiolanthanides. The heavy radiolanthanides can be classified as bone seeking metals, whereas the light and transition lanthanide elements accumulate mainly in the liver and the spleen. For the lighter radiolanthanides the corresponding ternary complexes thus represent an important transport form in blood. This physicochemical form of lanthanides mainly results in reticulo endothelial accumulation; on the other hand, the lower tendency of heavier lanthanides leads to preferential skeletal deposition. (orig.)

Development of Gradient Cemented Carbides Through ICME Strategy

Science.gov (United States)

Du, Yong; Peng, Yingbiao; Zhang, Weibin; Chen, Weimin; Zhou, Peng; Xie, Wen; Cheng, Kaiming; Zhang, Lijun; Wen, Guanghua; Wang, Shequan

An integrated computational materials engineering (ICME) including CALPHAD method is a powerful tool for materials process optimization and alloy design. The quality of CALPHAD-type calculations is strongly dependent on the quality of the thermodynamic and diffusivity databases. The development of a thermodynamic database, CSUTDCC1, and a diffusivity database, CSUDDCC1, for cemented carbides is described. Several gradient cemented carbides sintered under vacuum and various partial pressures of N2 have been studied via experiment and simulation. The microstructure and concentration profile of the gradient zones have been investigated via SEM and EPMA. Examples of ICME applications in design and manufacture for different kinds of cemented carbides are shown using the databases and comparing where possible against experimental data, thereby validating its accuracy.

Equilibria of perceptrons for simple contingency problems.

Science.gov (United States)

Dawson, Michael R W; Dupuis, Brian

2012-08-01

The contingency between cues and outcomes is fundamentally important to theories of causal reasoning and to theories of associative learning. Researchers have computed the equilibria of Rescorla-Wagner models for a variety of contingency problems, and have used these equilibria to identify situations in which the Rescorla-Wagner model is consistent, or inconsistent, with normative models of contingency. Mathematical analyses that directly compare artificial neural networks to contingency theory have not been performed, because of the assumed equivalence between the Rescorla-Wagner learning rule and the delta rule training of artificial neural networks. However, recent results indicate that this equivalence is not as straightforward as typically assumed, suggesting a strong need for mathematical accounts of how networks deal with contingency problems. One such analysis is presented here, where it is proven that the structure of the equilibrium for a simple network trained on a basic contingency problem is quite different from the structure of the equilibrium for a Rescorla-Wagner model faced with the same problem. However, these structural differences lead to functionally equivalent behavior. The implications of this result for the relationships between associative learning, contingency theory, and connectionism are discussed.

Three-point bending fatigue behavior of WC–Co cemented carbides

International Nuclear Information System (INIS)

Li, Anhai; Zhao, Jun; Wang, Dong; Gao, Xinliang; Tang, Hongwei

2013-01-01

Highlights: ► Mechanical fatigue tests were conducted on a specific designed jig. ► Three-point bending fatigue behavior of WC–Co cemented carbides was studied. ► Fatigue mechanisms of WC–Co cemented carbides with different WC grain sizes and Co binder contents were revealed. -- Abstract: WC–Co cemented carbides with different WC grain sizes and Co binder contents were sintered and fabricated. The three-point bending specimens with a single edge notch were prepared for tests. In the experiments, the mechanical properties of materials were investigated under static and cyclic loads (20 Hz) in air at room temperature. The fatigue behaviors of the materials under the same applied loading conditions are presented and discussed. Optical microscope and scanning electron microscopy were used to investigate the micro-mechanisms of damage during fatigue, and the results were used to correlate with the mechanical fatigue behavior of WC–Co cemented carbides. Experimental results indicated that the fatigue fracture surfaces exhibited more fracture origins and diversification of crack propagation paths than the static strength fracture surfaces. The fatigue fracture typically originates from inhomogeneities or defects such as micropores or aggregates of WC grains near the notch tip. Moreover, due to the diversity and complexity of the fatigue mechanisms, together with the evolution of the crack tip and the ductile deformation zone, the fatigue properties of WC–Co cemented carbides were largely relevant with the combination of transverse rupture strength and fracture toughness, rather than only one of them. Transverse rupture strength dominated the fatigue behavior of carbides with low Co content, whilst the fatigue behavior of carbides with high Co content was determined by fracture toughness.

Stress in tungsten carbide-diamond like carbon multilayer coatings

NARCIS (Netherlands)

Pujada, B.R.; Tichelaar, F.D.; Janssen, G.C.A.M.

2007-01-01

Tungsten carbide-diamond like carbon (WC-DLC) multilayer coatings have been prepared by sputter deposition from a tungsten-carbide target and periodic switching on and off of the reactive acetylene gas flow. The stress in the resulting WC-DLC multilayers has been studied by substrate curvature.

Morphology study of refractory carbide powders

International Nuclear Information System (INIS)

Vavrda, J.; Blazhikova, Ya.

1982-01-01

Refractory carbides were investigated using JSM-U3 electron microscope of Joelco company at 27 KV accelerating voltage. Some photographs of each powder were taken with different enlargements to characterise the sample upon the whole. It was shown that morphological and especially topographic study of powders enables to learn their past history (way of fabrication and treatment). The presence of steps of compact particle fractures and cracks is accompanied by occurence of fine dispersion of carbides subjected to machining after facrication. On the contrary, the character of crystallographic surfaces and features of surface growth testify to the way of crystallization

Separation of Nuclear Fuel Surrogates from Silicon Carbide Inert Matrix

International Nuclear Information System (INIS)

Baney, Ronald

2008-01-01

The objective of this project has been to identify a process for separating transuranic species from silicon carbide (SiC). Silicon carbide has become one of the prime candidates for the matrix in inert matrix fuels, (IMF) being designed to reduce plutonium inventories and the long half-lives actinides through transmutation since complete reaction is not practical it become necessary to separate the non-transmuted materials from the silicon carbide matrix for ultimate reprocessing. This work reports a method for that required process

Hydrotreatment activities of supported molybdenum nitrides and carbides

Energy Technology Data Exchange (ETDEWEB)

Dolce, G.M.; Savage, P.E.; Thompson, L.T. [University of Michigan, Ann Arbor, MI (United States). Dept. of Chemical Engineering

1997-05-01

The growing need for alternative sources of transportation fuels encourages the development of new hydrotreatment catalysts. These catalysts must be active and more hydrogen efficient than the current commercial hydrotreatment catalysts. Molybdenum nitrides and carbides are attractive candidate materials possessing properties that are comparable or superior to those of commercial sulfide catalysts. This research investigated the catalytic properties of {gamma}-Al{sub 2}O{sub 3}-supported molybdenum nitrides and carbides. These catalysts were synthesized via temperature-programmed reaction of supported molybdenum oxides with ammonia or methane/hydrogen mixtures. Phase constituents and compositions were determined by X-ray diffraction, elemental analysis, and neutral activation analysis. Oxygen chemisorption was used to probe the surface properties of the catalysts. Specific activities of the molybdenum nitrides and carbides were competitive with those of a commercial sulfide catalyst for hydrodenitrogenation (HDN), hydrodesulfurization (HDS), and hydrodeoxygenation (HDO). For HDN and HDS, the catalytic activity on a molybdenum basis was a strong inverse function of the molybdenum loading. Product distributions of the HDN, HDO and HDS of a variety of heteroatom compounds indicated that several of the nitrides and carbides were more hydrogen efficient than the sulfide catalyst. 35 refs., 8 figs., 7 tabs.

Influence of nanometric silicon carbide on phenolic resin composites ...

Indian Academy of Sciences (India)

Abstract. This paper presents a preliminary study on obtaining and characterization of phenolic resin-based com- posites modified with nanometric silicon carbide. The nanocomposites were prepared by incorporating nanometric silicon carbide (nSiC) into phenolic resin at 0.5, 1 and 2 wt% contents using ultrasonication to ...

Experimental and thermodynamic study of the Mg–Sn–In–Zn quaternary system

International Nuclear Information System (INIS)

Wang, Jian; Hudon, Pierre; Kevorkov, Dmytro; Chartrand, Patrice; Jung, In-Ho; Medraj, Mamoun

2014-01-01

Highlights: • Phase equilibria in the Mg-rich region of the Mg–Sn–In are determined. • Phase equilibria in the Mg-rich region of the Mg–Sn–Zn are determined. • Evaluation and thermodynamic optimization of the Mg–Sn–In–Zn quaternary system are developed. -- Abstract: Phase equilibria in the Mg-rich region of the Mg–Sn–In (at 415 °C and 330 °C), and Mg–Sn–Zn (at 300 °C) ternary systems were determined by quenching experiments, electron probe micro-analyzer (EPMA), and X-ray diffraction (XRD) techniques. The ternary isoplethal sections with constant 5 In and 10 Sn at.% of Mg–In–Sn system, and 10 Sn at.% of Mg–In–Zn system were determined by differential scanning calorimetry (DSC). No ternary compounds were found in the Mg–Sn–Zn and Mg–Sn–In isothermal sections. Critical evaluation and thermodynamic optimization of the Mg–Sn–In–Zn quaternary system were carried out using CALPHAD (Calculation of Phase Diagrams) technique. The Modified Quasichemical Model in the Pair Approximation (MQMPA) was used for modeling the liquid solution, which exhibits a high degree of short-range ordering behavior. The solid phases were modeled with the Compound Energy Formalism (CEF). All available and reliable experimental data were reproduced within experimental error limits. A self-consistent thermodynamic database was constructed for the Mg–Sn–In–Zn quaternary system, which can be used as a guide for Mg-based alloys development

Kinetic stability constraints on magnetized plasma equilibria: Quasi-particle approach

International Nuclear Information System (INIS)

Sosenko, P.; Weiland, J.

1996-01-01

Macroscopic adiabatic invariants for the magnetized plasma are studied within the context of the quasi-particle description, as well as constraints which they impose on energy transfer and stable plasma equilibria. 6 refs

Electrocatalysis on tungsten carbide

International Nuclear Information System (INIS)

Fleischmann, R.

1975-01-01

General concepts of electrocatalysis, the importance of the equilibrium rest potential and its standardization on polished WC-electrodes, the influence of oxygen in the catalysts upon the oxidation of hydrogen, and the attained results of the hydrogen oxidation on tungsten carbide are treated. (HK) [de

A periodic point-based method for the analysis of Nash equilibria in 2 x 2 symmetric quantum games

International Nuclear Information System (INIS)

Schneider, David

2011-01-01

We present a novel method of looking at Nash equilibria in 2 x 2 quantum games. Our method is based on a mathematical connection between the problem of identifying Nash equilibria in game theory, and the topological problem of the periodic points in nonlinear maps. To adapt our method to the original protocol designed by Eisert et al (1999 Phys. Rev. Lett. 83 3077-80) to study quantum games, we are forced to extend the space of strategies from the initial proposal. We apply our method to the extended strategy space version of the quantum Prisoner's dilemma and find that a new set of Nash equilibria emerge in a natural way. Nash equilibria in this set are optimal as Eisert's solution of the quantum Prisoner's dilemma and include this solution as a limit case.

Structure and single-phase regime of boron carbides

International Nuclear Information System (INIS)

Emin, D.

1988-01-01

The boron carbides are composed of twelve-atom icosahedral clusters which are linked by direct covalent bonds and through three-atom intericosahedral chains. The boron carbides are known to exist as a single phase with carbon concentrations from about 8 to about 20 at. %. This range of carbon concentrations is made possible by the substitution of boron and carbon atoms for one another within both the icosahedra and intericosahedral chains. The most widely accepted structural model for B 4 C (the boron carbide with nominally 20% carbon) has B/sub 11/C icosahedra with C-B-C intericosahedral chains. Here, the free energy of the boron carbides is studied as a function of carbon concentration by considering the effects of replacing carbon atoms within B 4 C with boron atoms. It is concluded that entropic and energetic considerations both favor the replacement of carbon atoms with boron atoms within the intericosahedral chains, C-B-C→C-B-B. Once the carbon concentration is so low that the vast majority of the chains are C-B-B chains, near B/sub 13/C 2 , subsequent substitutions of carbon atoms with boron atoms occur within the icosahedra, B/sub 11/C→B/sub 12/. Maxima of the free energy occur at the most ordered compositions: B 4 C,B/sub 13/C 2 ,B/sub 14/C. This structural model, determined by studying the free energy, agrees with that previously suggested by analysis of electronic and thermal transport data. These considerations also provide an explanation for the wide single-phase regime found for boron carbides

Single-Event Effects in Silicon Carbide Power Devices

Science.gov (United States)

Lauenstein, Jean-Marie; Casey, Megan C.; LaBel, Kenneth A.; Ikpe, Stanley; Topper, Alyson D.; Wilcox, Edward P.; Kim, Hak; Phan, Anthony M.

2015-01-01

This report summarizes the NASA Electronic Parts and Packaging Program Silicon Carbide Power Device Subtask efforts in FY15. Benefits of SiC are described and example NASA Programs and Projects desiring this technology are given. The current status of the radiation tolerance of silicon carbide power devices is given and paths forward in the effort to develop heavy-ion single-event effect hardened devices indicated.

Ideal MHD stability of high poloidal beta equilibria in TFTR

International Nuclear Information System (INIS)

Sabbagh, S.A.; Mauel, M.E.; Navratil, G.A.; Bell, M.G.; Budny, R.V.; Chance, M.S.; Fredrickson, E.D.; Jardin, S.C.; Manickam, J.; McCune, D.C.; McGuire, K.M.; Wieland, R.M.; Zarnstorff, M.C.; Phillips, M.W.; Hughes, M.H.; Kesner, J.

1991-01-01

Recent experiments in TFTR have expanded the operating space of the device to include plasmas with values of var-epsilon β p dia ≡ 2μ 0 var-epsilon perpendicular >/ p >> 2 as large as 1.6, and Troyon normalized diamagnetic beta β N dia ≡ β t perpendicular aB t /10 -8 I p as large as 4.7. At values of var-epsilon β p dia ≥ 1.3, a separatrix was observed to enter the vacuum vessel, producing a naturally diverted discharge. Plasmas with large values of var-epsilon β p dia were created with both the plasma current, I p , held constant and with I p decreased, or ramped down, before the start of neutral beam injection. A convenient characterization of the change in I p using experimental parameters can be defined by the ratio of I p before the ramp down, to I p during the neutral beam heating phase, F I p . The ideal MHD stability of these equilibria is investigated to determine their location in stability space, and to study the role of plasma current and pressure profile modification in the creation of these high var-epsilon β p and β N plasmas. The evolution of these plasmas is modelled from experimental data using the TRANSP code. Two-dimensional equilibria are computed from the TRANSP results and used as input to both high and low-n stability codes including PEST. The high var-epsilon β p equilibria, which generally have an oblate cross-sectional shape, are in the first stability region to high-n ballooning modes. At constant I p , these equilibria generally have maximum pressure gradients near the magnetic axis and are stable to n=1 modes without a stabilizing conducting wall. The effect of the current profile shape on the stability of low-n kink/ballooning modes and the requirements for these plasmas to access the second stability region are examined. 6 refs

Estimation of sesqui-carbide fraction for MARK-I fuel

International Nuclear Information System (INIS)

Vana Varamban, S.; Ananthasivan, K.

2016-01-01

Sesqui-carbide content of FBTR bi-phasic mixed carbide is specified as 5-20 wt.%. For each batch of fuel production, the sesqui-carbide (M2C3) content is being determined by a K-ratio method using XRD information. There is a need to evolve an alternate method for qualitative determination of M2C3 content for a fabricated FBTR fuel pellet. Two independent approaches resulted in a correlation between overall carbon content and the M2C3 phase fraction. The thermodynamic calculations agree well with the stoichiometric correlation between the overall carbon content and the M2C3 phase fraction in FBTR MARK I fuel

Asymmetric supercapacitors with metal-like ternary selenides and porous graphene electrodes

KAUST Repository

Xia, Chuan; Jiang, Qiu; Zhao, Chao; Beaujuge, Pierre; Alshareef, Husam N.

2016-01-01

nanostructured ternary nickel cobalt selenides result in a much higher areal capacitance (2.33 F cm−2 at 4 mA cm−2), better rate performance and cycling stability than their binary selenide equivalents, and other ternary oxides and chalcogenides. Those hybrid

Electronic specific heat of transition metal carbides

International Nuclear Information System (INIS)

Conte, R.

1964-07-01

The experimental results that make it possible to define the band structure of transition metal carbides having an NaCI structure are still very few. We have measured the electronic specific heat of some of these carbides of varying electronic concentration (TiC, either stoichiometric or non-stoichiometric, TaC and mixed (Ti, Ta) - C). We give the main characteristics (metallography, resistivity, X-rays) of our samples and we describe the low temperature specific heat apparatus which has been built. In one of these we use helium as the exchange gas. The other is set up with a mechanical contact. The two use a germanium probe for thermometer. The measurement of the temperature using this probe is described, as well as the various measurement devices. The results are presented in the form of a rigid band model and show that the density of the states at the Fermi level has a minimum in the neighbourhood of the group IV carbides. (author) [fr

Carbide coated fibers in graphite-aluminum composites

Science.gov (United States)

Imprescia, R. J.; Levinson, L. S.; Reiswig, R. D.; Wallace, T. C.; Williams, J. M.

1975-01-01

The NASA-supported program at the Los Alamos Scientific Laboratory (LASL) to develop carbon fiber-aluminum matrix composites is described. Chemical vapor deposition (CVD) was used to uniformly deposit thin, smooth, continuous coats of TiC on the fibers of graphite tows. Wet chemical coating of fibers, followed by high-temperature treatment, was also used, but showed little promise as an alternative coating method. Strength measurements on CVD coated fiber tows showed that thin carbide coats can add to fiber strength. The ability of aluminum alloys to wet TiC was successfully demonstrated using TiC-coated graphite surfaces. Pressure-infiltration of TiC- and ZrC-coated fiber tows with aluminum alloys was only partially successful. Experiments were performed to evaluate the effectiveness of carbide coats on carbon as barriers to prevent reaction between alluminum alloys and carbon. Initial results indicate that composites of aluminum and carbide-coated graphite are stable for long periods of time at temperatures near the alloy solidus.

Development and testing of a new apparatus for the measurement of high-pressure low-temperature phase equilibria

DEFF Research Database (Denmark)

Fonseca, José M.S.; von Solms, Nicolas

2012-01-01

A new apparatus for the study of high-pressure phase equilibria at low temperatures using an analytical method was designed, assembled and tested. The apparatus was specially developed for the study of multi-phase equilibria in systems containing hydrocarbons, water and hydrate inhibitors, at tem...

Effect of carbides on the creep properties of a Ni-base superalloy M963

International Nuclear Information System (INIS)

He, L.Z.; Zheng, Q.; Sun, X.F.; Guan, H.R.; Hu, Z.Q.; Tieu, A.K.; Lu, C.; Zhu, H.T.

2005-01-01

Effect of carbides on the creep properties of a cast Ni-base superalloy M963 tested at 800 and 900 deg. C over a broad stress range has been investigated. Correlation between the carbides and creep properties of the alloy is enabled through scanning electron microscopy (SEM) and transmission electron microscopy (TEM). During high temperature creep tests, the primary MC carbide decomposes sluggishly and a large amount of secondary carbides precipitate. The cubic and acicular M 6 C carbide precipitates at the dendritic core region. Extremely fine chromium-rich M 23 C 6 carbide precipitates preferentially at grain boundaries. The M 6 C and M 23 C 6 carbides are found to be beneficial to the creep properties of the alloy. At lower temperature (800 deg. C), the interface of MC carbide with matrix is one of the principal sites for crack initiation. At higher temperature (900 deg. C), the oxidation and the precipitation of μ phase are the main factors for significant loss in creep strength of the alloy

A new method to estimate the atomic volume of ternary intermetallic compounds

International Nuclear Information System (INIS)

Pani, M.; Merlo, F.

2011-01-01

The atomic volume of an A x B y C z ternary intermetallic compound can be calculated starting from volumes of some proper A-B, A-C and B-C binary phases. The three methods by Colinet, Muggianu and Kohler, originally used to estimate thermodynamic quantities, and a new method here proposed, were tested to derive volume data in eight systems containing 91 ternary phases with the known structure. The comparison between experimental and calculated volume values shows the best agreement both for the Kohler method and for the new proposed procedure. -- Graphical abstract: Synopsys: the volume of a ternary intermetallic compound can be calculated starting from volumes of some binary phases, selected by the methods of Colinet, Muggianu, Kohler and a new method proposed here. The so obtained values are compared with the experimental ones for eight ternary systems. Display Omitted Research highlights: → The application of some thermodinamic methods to a crystallochemical problem. → The prevision of the average atomic volume of ternary intermetallic phases. → The proposal of a new procedure to select the proper starting set of binary phases.

First-principles study of ternary bcc alloys using special quasi-random structures

International Nuclear Information System (INIS)

Jiang Chao

2009-01-01

Using a combination of exhaustive enumeration and Monte Carlo simulated annealing, we have developed special quasi-random structures (SQSs) for ternary body-centered cubic (bcc) alloys with compositions of A 1 B 1 C 1 , A 2 B 1 C 1 , A 6 B 1 C 1 and A 2 B 3 C 3 , respectively. The structures possess local pair and multisite correlation functions that closely mimic those of the random bcc alloy. We employed the SQSs to predict the mixing enthalpies, nearest neighbor bond length distributions and electronic density of states of bcc Mo-Nb-Ta and Mo-Nb-V solid solutions. Our convergence tests indicate that even small-sized SQSs can give reliable results. Based on the SQS energetics, the predicting powers of the existing empirical ternary extrapolation models were assessed. The present results suggest that it is important to take into account the ternary interaction parameter in order to accurately describe the thermodynamic behaviors of ternary alloys. The proposed SQSs are quite general and can be applied to other ternary bcc alloys.

Temperature dependence of binary and ternary recombination of H3+ ions with electrons

International Nuclear Information System (INIS)

Glosik, J.; Plasil, R.; Korolov, I.; Kotrik, T.; Novotny, O.; Hlavenka, P.; Dohnal, P.; Varju, J.; Kokoouline, V.; Greene, Chris H.

2009-01-01

We study binary and the recently discovered process of ternary He-assisted recombination of H 3 + ions with electrons in a low-temperature afterglow plasma. The experiments are carried out over a broad range of pressures and temperatures of an afterglow plasma in a helium buffer gas. Binary and He-assisted ternary recombination are observed and the corresponding recombination rate coefficients are extracted for temperatures from 77 to 330 K. We describe the observed ternary recombination as a two-step mechanism: first, a rotationally excited long-lived neutral molecule H 3 * is formed in electron-H 3 + collisions. Second, the H 3 * molecule collides with a helium atom that leads to the formation of a very long-lived Rydberg state with high orbital momentum. We present calculations of the lifetimes of H 3 * and of the ternary recombination rate coefficients for para- and ortho-H 3 + . The calculations show a large difference between the ternary recombination rate coefficients of ortho- and para-H 3 + at temperatures below 300 K. The measured binary and ternary rate coefficients are in reasonable agreement with the calculated values.

Temperature dependence of binary and ternary recombination of H3+ ions with electrons

Science.gov (United States)

Glosík, J.; Plašil, R.; Korolov, I.; Kotrík, T.; Novotný, O.; Hlavenka, P.; Dohnal, P.; Varju, J.; Kokoouline, V.; Greene, Chris H.

2009-05-01

We study binary and the recently discovered process of ternary He-assisted recombination of H3+ ions with electrons in a low-temperature afterglow plasma. The experiments are carried out over a broad range of pressures and temperatures of an afterglow plasma in a helium buffer gas. Binary and He-assisted ternary recombination are observed and the corresponding recombination rate coefficients are extracted for temperatures from 77 to 330 K. We describe the observed ternary recombination as a two-step mechanism: first, a rotationally excited long-lived neutral molecule H3∗ is formed in electron- H3+ collisions. Second, the H3∗ molecule collides with a helium atom that leads to the formation of a very long-lived Rydberg state with high orbital momentum. We present calculations of the lifetimes of H3∗ and of the ternary recombination rate coefficients for para- and ortho- H3+ . The calculations show a large difference between the ternary recombination rate coefficients of ortho- and para- H3+ at temperatures below 300 K. The measured binary and ternary rate coefficients are in reasonable agreement with the calculated values.

Ternary Fission of U235 by Resonance Neutrons

International Nuclear Information System (INIS)

Kvitek, I.; Popov, Ju.P.; Rjabov, Ju.V.

1965-01-01

Recently a number of papers have appeared indicating considerable variations in the ratio of the ternary-fission cross-section to the binary-fission cross-section of U 235 on transition from one neutron resonance to another. However, such variations have not been discovered in U 233 and Pu 239 . The paper reports investigations of the ternary fission of U 235 by neutrons with an energy of 0.1 to 30 eV. Unlike other investigators of the ternary fission of U 235 , we identified the ternary-fission event by the coincidence of one of the fission fragments with a light long-range particle. This made it passible to separate ternary fissions from the possible contribution of the (n, α)reaction. The measurements were performed at the fast pulsed reactor of the Joint Institute for Nuclear Research by the time-of-flight method. A flight length of 100 m was used, giving a resolution of 0.6 μs/m. Gas scintillation counters filled with xenon at a pressure of 2 atm were used to record the fission fragments and the light long-range particle. A layer of enriched U 235 ∼2 mg/cm 2 thick and ∼300 cm 2 in area was applied to an aluminium foil 20-fim thick. The scintillations from the fission fragments were recorded in the gas volume on one side of the foil and those from the light long-range particles in that on the other. In order to assess the background (e.g . coincidences of the pulse from a fragment with that from a fission gamma quantum or a proton from the (n, p) reaction in the aluminium foil), a measurement was carried out in which the volume recording the long-range particle was shielded with a supplementary aluminium filter 1-mm thick. The results obtained indicate the absence of the considerable variations in the ratio between the ternary-and binary- fission cross-sections for U 235 that have been noted by other authors. Measurements showed no irregularity in the ratio of the cross-sections in the energy range 0.1 to 0.2 eV. The paper discusses the possible effect of

On pure-strategy Nash equilibria in price-quantity games

NARCIS (Netherlands)

Bos, I.; Vermeulen, A.J.

2015-01-01

This paper examines the existence and characteristics of pure-strategy Nash equilibria in oligopoly models in which firms set both prices and quantities. Existence is proved for a broad and natural class of price-quantity games. With differentiated products, the equilibrium outcome is similar to

Stability of equilibria for a two-phase osmosis model

NARCIS (Netherlands)

Lippoth, F.; Prokert, G.

2012-01-01

For a two-phase moving boundary problem modelling the motion of a semipermeable membrane by osmotic pressure and surface tension, we prove that the manifold of equilibria is locally exponentially attractive. Our method relies on maximal regularity results for parabolic systems with relaxation type

Corrosion behaviour of porous chromium carbide/oxide based ceramics in supercritical water

International Nuclear Information System (INIS)

Dong, Z.; Xin, T.; Chen, W.; Zheng, W.; Guzonas, D.

2011-01-01

Porous chromium carbide with a high density of open pores was fabricated by a reactive sintering method. Chromium oxide ceramics were obtained by re-oxidizing the porous chromium carbides formed. Some samples were added with yttria at 5 wt. %, prior to reactive sintering to form porous structures. Corrosion tests in SCW were performed at temperatures ranging from 375 o C to 625 o C with a fixed pressure at around 25∼30 MPa. The results show that chromium carbide is stable in SCW environments at temperatures up to 425 o C, above which disintegration of carbides through oxidation occurs. Porous chromium oxide samples show better corrosion resistance than porous chromium carbide, but disintegrate in SCW at around 625 o C. Among all the samples tested, chromium oxide ceramics with added yttria exhibited much better corrosion resistance compared with the pure chromium carbide/oxides. No evidence of weight change or disintegration of porous chromium oxides with 5 wt % added yttria was observed after exposure at 625 o C in SCW for 600 hours. (author)

Colloidal characterization of ultrafine silicon carbide and silicon nitride powders

Science.gov (United States)

Whitman, Pamela K.; Feke, Donald L.

1986-01-01

The effects of various powder treatment strategies on the colloid chemistry of aqueous dispersions of silicon carbide and silicon nitride are examined using a surface titration methodology. Pretreatments are used to differentiate between the true surface chemistry of the powders and artifacts resulting from exposure history. Silicon nitride powders require more extensive pretreatment to reveal consistent surface chemistry than do silicon carbide powders. As measured by titration, the degree of proton adsorption from the suspending fluid by pretreated silicon nitride and silicon carbide powders can both be made similar to that of silica.

New ternary hydride formation in U-Ti-H system

International Nuclear Information System (INIS)

Yamamoto, Takuya; Kayano, Hideo; Yamawaki, Michio.

1991-01-01

Hydrogen absorption properties of two titanium-rich uranium alloys, UTi 2 and UTi 4 , were studied in order to prepare and identify the recently found ternary hydride. They slowly reacted with hydrogen of the initial pressure of 10 5 Pa at 873K to form the ternary hydride. The hydrogenated specimen mainly consisted of the pursued ternary hydride but contained also U(or UO 2 ), TiH x , and some transient phases. X-ray powder diffraction and Electron Probe Micro Analysis proved that it was the UTi 2 H x with the expected MgCu 2 structure, though all the X-ray peaks were broad probably because of inhomogeneity. This compound had extremely high resistance to powdering on its formation, which showed high potential utilities for a non-powdering tritium storage system or for other purposes. (author)