Experimental Facilities Division/User Program Division technical progress report 1999-2000

International Nuclear Information System (INIS)

2001-01-01

In October 1999, the two divisions of the Advanced Photon Source (APS), the Accelerator Systems Division (ASD) and the Experimental Facilities Division (XFD), were reorganized into four divisions (see high-level APS organizational chart, Fig. 1.1). In addition to ASD and XFD, two new divisions were created, the APS Operations Division (AOD), to oversee APS operations, and the User Program Division (UPD), to serve the APS user community by developing and maintaining the highest quality user technical and administration support. Previous XFD Progress Reports (ANL/APS/TB-30 and ANL/APS/TB-34) covered a much broader base, including APS user administrative support and what was previously XFD operations (front ends, interlocks, etc.) This Progress Report summarizes the main scientific and technical activities of XFD, and the technical support, research and development (R and D) activities of UPD from October 1998 through November 2000. The report is divided into four major sections, (1) Introduction, (2) SRI-CAT Beamlines, Technical Developments, and Scientific Applications, (3) User Technical Support, and (4) Major Plans for the Future. Sections 2 and 3 describe the technical activities and research accomplishments of the XFD and UPD personnel in supporting the synchrotron radiation instrumentation (SRI) collaborative access team (CAT) and the general APS user community. Also included in this report is a comprehensive list of publications (Appendix 1) and presentations (Appendix 2) by XFD and UPD staff during the time period covered by this report. The organization of section 2, SRI CAT Beamlines, Technical Developments, and Scientific Applications has been made along scientific techniques/disciplines and not ''geographical'' boundaries of the sectors in which the work was performed. Therefore items under the subsection X-ray Imaging and Microfocusing could have been (and were) performed on several different beamlines by staff in different divisions. The management of

Comparative technical-economic analysis of the low temperature heating systems

International Nuclear Information System (INIS)

Sharevski, Vasko; Sharevski, Milan

1994-01-01

A method for comparative technical-economic analysis between low temperature heating systems and heating systems with fossil fuel boiler plant, heat pump heating system and electrical heating systems is presented. The single and combined heating systems are analyzed. The technical-economic priority application of the heating system is determined according to the prices of the low temperature heat energy, fossil fuel heat energy, electrical energy, as well as to the coefficient of the annual use of the installed heating capacity, investment expenses, structure of the combined heating system and coefficient of performances of the heat pump. The combined heating system, composed with a low temperature heating subsystem, which is used to cover the base heat demands, and a oil boiler plant heating subsystem, for the top heat demands, have technical-economic justification and wide range of priority application, in comparison with single heating systems. (author)

ARCHER Project: Progress on Material and component activities for the Advanced High Temperature Reactor

International Nuclear Information System (INIS)

Buckthorpe, D.E.

2014-01-01

The ARCHER (Advanced High-Temperature Reactors for Cogeneration of Heat and Electricity R&D) integrated project is a four year project which was started in 2011 as part of the European Commission 7th Framework Programme (FP7) to perform High Temperature Reactor technology R&D in support of reactor demonstration. The project consortium encompasses conventional and Nuclear Industry, Utilities, Technical Support Organizations, Research & Development Organizations and Academia. The activities involved contribute to the Generation IV (GIF) International Forum and collaborate with related projects in the US, China, Japan, and the Republic of Korea in cooperation with IAEA and ISTC. This paper addresses the progress of the work on ARCHER materials and component activities since the start of the project and underlines some of the main conclusions reached. (author)

The effects of environmental regulation and technical progress on CO2 Kuznets curve: An evidence from China

International Nuclear Information System (INIS)

Yin, Jianhua; Zheng, Mingzheng; Chen, Jian

2015-01-01

Based on environmental Kuznets curve theory, a panel data model which takes environmental regulation and technical progress as its moderating factors was developed to analyse the institutional and technical factors that affect the path of low-carbon economic development. The results indicated that there was a CO 2 emission Kuznets curve seen in China. Environmental regulation had a significant moderating effect on the curve, and the inflection of CO 2 emissions could come substantially earlier under stricter environmental regulation. Meanwhile, the impact of technical progress on the low-carbon economic development path had a longer hysteresis effect but restrained CO 2 emission during its increasing stage and accelerated its downward trend during the decreasing stage which was conducive to emission reduction. Strict environmental regulation could force the high-carbon emitting industries to transfer from the eastern regions to the central or the western regions of China, which would make the CO 2 Kuznets curve higher in its increasing stage and lower in its decreasing stage than that under looser regulation. Furthermore, energy efficiency, energy structure, and industrial structure exerted a significant direct impact on CO 2 emissions; we should consider the above factors as essential in the quest for low-carbon economic development. - Highlights: • Estimate moderating effect of environmental regulation and technical progress on EKC. • There was a CO 2 emission Kuznets curve in effect in China. • Environmental regulation presents significant moderating effect on EKC. • Technical progress moderates the relationship between income and CO 2 emissions

ERIP invention 637. Technical progress report 2nd quarter, April 1997--June 1997

Energy Technology Data Exchange (ETDEWEB)

Thacker, G.W.

1997-07-22

This technical report describes progress in the development of the Pegasus plow, a stalk and root embedding apparatus. Prototype testing is reported, and includes the addition of precision tillage. Disease data, organic matter, and nitrogen levels results are very briefly described. Progress in marketing is also reported. Current marketing issues include test use by cotton and wheat growers, establishment of dealer relationships, incorporation of design modifications, expansion of marketing activities, and expansion of loan and lease program.

Cassini RTG Program. Monthly technical progress report, 27 November--31 December 1995

International Nuclear Information System (INIS)

1996-01-01

This monthly technical progress report provided information on the following tasks: spacecraft integration and liaison; engineering support; safety analysis; qualified unicouple fabrication; ETG fabrication, assembly, and test; ground support equipment (GSE); RTG shipping and launch support; designs, reviews, and mission applications; project management, quality assurance, and reliability, and contractor acquired government owned (CAGO) property acquisition

Impact of Environmental Regulation and Technical Progress on Industrial Carbon Productivity: An Approach Based on Proxy Measure

Directory of Open Access Journals (Sweden)

Huan Zhang

2016-08-01

Full Text Available This research aims to study the main influencing factors of China’s industrial carbon productivity by incorporating environmental regulation and technical progress into an econometric model. The paper focuses on data from 35 of China’s industrial sectors and covers the period from 2006 to 2014, in order to examine the impact of environmental regulation and technical progress on carbon productivity. Methods applied include panel fixed effect model, panel random effect model and two stage least squares with instrumental variables (IV-2SLS. The effect of environmental regulation and technical progress has industrial heterogeneity. The paper subdivides industrial sectors into capital and technology intensive, resource intensive and labor intensive sectors according to factor intensiveness. The estimation results of the subgroups have uncovered that for capital and technology intensive and resource intensive sectors, environmental regulation has a more significant impact than technical progress; while for labor intensive sectors, innovation more significantly influences carbon productivity. In addition, foreign direct investment (FDI and industrialization level facilitate improving carbon productivity for the full sample. By contrast, industrial structure inhibits the overall industrial carbon productivity. The industry-specific results indicate that for capital and technology intensive sectors, optimizing of the industrial structure can improve carbon productivity; for resource intensive sectors, FDI and energy consumption structure should be emphasized more; for labor intensive sectors, industrialization levels help enhance carbon productivity. Finally the industrial sector-specific policy suggestions are proposed.

Annual technical progress report: reactor safety, Government fiscal year 1978

International Nuclear Information System (INIS)

1978-01-01

Progress in LMFBR safety studies on accident debris behavior is reported under the following subtask titles: high-temperature-concentration aerosols, large-scale molten fuel tests, sodium release tests, and risk analysis

Monitoring the Durability Performance of Concrete in Nuclear Waste Containment. Technical Progress Report No. 3

International Nuclear Information System (INIS)

Ulm, Franz-Josef

2000-01-01

OAK-B135 Monitoring the Durability Performance of Concrete in Nuclear Waste Containment. Technical Progress Report No. 3(NOTE: Part II A item 1 indicates ''PAPER'', but a report is attached electronically)

Total Factor Productivity Growth, Technical Progress & Efficiency Change in Vietnam Coal Industry - Nonparametric Approach

Science.gov (United States)

Phuong, Vu Hung

2018-03-01

This research applies Data Envelopment Analysis (DEA) approach to analyze Total Factor Productivity (TFP) and efficiency changes in Vietnam coal mining industry from 2007 to 2013. The TFP of Vietnam coal mining companies decreased due to slow technological progress and unimproved efficiency. The decadence of technical efficiency in many enterprises proved that the coal mining industry has a large potential to increase productivity through technical efficiency improvement. Enhancing human resource training, technology and research & development investment could help the industry to improve efficiency and productivity in Vietnam coal mining industry.

Sludge Treatment Evaluation: 1992 Technical progress

International Nuclear Information System (INIS)

Silva, L.J.; Felmy, A.R.; Ding, E.R.

1993-01-01

This report documents Fiscal Year 1992 technical progress on the Sludge Treatment Evaluation Task, which is being conducted by Pacific Northwest Laboratory. The objective of this task is to develop a capability to predict the performance of pretreatment processes for mixed radioactive and hazardous waste stored at Hanford and other US Department of Energy (DOE) sites. Significant cost savings can be achieved if radionuclides and other undesirable constituents can be effectively separated from the bulk waste prior to final treatment and disposal. This work is initially focused on chemical equilibrium prediction of water washing and acid or base dissolution of Hanford single-shell tank (SST) sludges, but may also be applied to other steps in pretreatment processes or to other wastes. Although SST wastes contain many chemical species, there are relatively few constituents -- Na, Al, NO 3 , NO 2 , PO 4 , SO 4 , and F -- contained in the majority of the waste. These constituents comprise 86% and 74% of samples from B-110 and U-110 SSTS, respectively. The major radionuclides of interest (Cs, Sr, Tc, U) are present in the sludge in small molal quantities. For these constituents, and other important components that are present in small molal quantities, the specific ion-interaction terms used in the Pitzer or NRTL equations may be assumed to be zero for a first approximation. Model development can also be accelerated by considering only the acid or base conditions that apply for the key pretreatment steps. This significantly reduces the number of chemical species and chemical reactions that need to be considered. Therefore, significant progress can be made by developing all the specific ion interactions for a base model and an acid dissolution model

Sludge Treatment Evaluation: 1992 Technical progress

Energy Technology Data Exchange (ETDEWEB)

Silva, L J; Felmy, A R; Ding, E R

1993-01-01

This report documents Fiscal Year 1992 technical progress on the Sludge Treatment Evaluation Task, which is being conducted by Pacific Northwest Laboratory. The objective of this task is to develop a capability to predict the performance of pretreatment processes for mixed radioactive and hazardous waste stored at Hanford and other US Department of Energy (DOE) sites. Significant cost savings can be achieved if radionuclides and other undesirable constituents can be effectively separated from the bulk waste prior to final treatment and disposal. This work is initially focused on chemical equilibrium prediction of water washing and acid or base dissolution of Hanford single-shell tank (SST) sludges, but may also be applied to other steps in pretreatment processes or to other wastes. Although SST wastes contain many chemical species, there are relatively few constituents -- Na, Al, NO[sub 3], NO[sub 2], PO[sub 4], SO[sub 4], and F -- contained in the majority of the waste. These constituents comprise 86% and 74% of samples from B-110 and U-110 SSTS, respectively. The major radionuclides of interest (Cs, Sr, Tc, U) are present in the sludge in small molal quantities. For these constituents, and other important components that are present in small molal quantities, the specific ion-interaction terms used in the Pitzer or NRTL equations may be assumed to be zero for a first approximation. Model development can also be accelerated by considering only the acid or base conditions that apply for the key pretreatment steps. This significantly reduces the number of chemical species and chemical reactions that need to be considered. Therefore, significant progress can be made by developing all the specific ion interactions for a base model and an acid dissolution model.

Decontamination Systems Information and Research Program. Quarterly technical progress report, January 1--March 31, 1994

Energy Technology Data Exchange (ETDEWEB)

1994-05-01

West Virginia University (WVU) and the US DOE Morgantown Energy Technology Center (METC) entered into a Cooperative Agreement on August 29, 1992 entitled ``Decontamination Systems Information and Research Programs.`` Stipulated within the Agreement is the requirement that WVU submit to METC a series of Technical Progress Reports on a quarterly basis. This report comprises the first Quarterly Technical Progress Report for Year 2 of the Agreement. This report reflects the progress and/or efforts performed on the sixteen (16) technical projects encompassed by the Year 2 Agreement for the period of January 1 through March 31, 1994. In situ bioremediation of chlorinated organic solvents; Microbial enrichment for enhancing in-situ biodegradation of hazardous organic wastes; Treatment of volatile organic compounds (VOCs) using biofilters; Drain-enhanced soil flushing (DESF) for organic contaminants removal; Chemical destruction of chlorinated organic compounds; Remediation of hazardous sites with steam reforming; Soil decontamination with a packed flotation column; Use of granular activated carbon columns for the simultaneous removal of organics, heavy metals, and radionuclides; Monolayer and multilayer self-assembled polyion films for gas-phase chemical sensors; Compact mercuric iodide detector technology development; Evaluation of IR and mass spectrometric techniques for on-site monitoring of volatile organic compounds; A systematic database of the state of hazardous waste clean-up technologies; Dust control methods for insitu nuclear and hazardous waste handling; Winfield Lock and Dam remediation; and Socio-economic assessment of alternative environmental restoration technologies.

Environmental Research Division technical progress report, January 1984-December 1985

International Nuclear Information System (INIS)

1986-05-01

Technical progress in the various research and assessment activities of Argonne National Laboratory's Environmental Research Division is reported for the period 1984 to 1985. Textual, graphic, and tabular information is used to briefly summarize (in separate chapters) the work of the Division's Atmospheric Physics, Environmental Effects Research, Environmental Impacts, Fundamental Molecular Physics and Chemistry, and Waste Management Programs. Information on professional qualifications, awards, and outstanding professional activities of staff members, as well as lists of publications, oral presentations, special events organized, and participants in educational programs, are provided in appendices at the end of each chapter

Environmental Research Division technical progress report, January 1984-December 1985

Energy Technology Data Exchange (ETDEWEB)

1986-05-01

Technical progress in the various research and assessment activities of Argonne National Laboratory's Environmental Research Division is reported for the period 1984 to 1985. Textual, graphic, and tabular information is used to briefly summarize (in separate chapters) the work of the Division's Atmospheric Physics, Environmental Effects Research, Environmental Impacts, Fundamental Molecular Physics and Chemistry, and Waste Management Programs. Information on professional qualifications, awards, and outstanding professional activities of staff members, as well as lists of publications, oral presentations, special events organized, and participants in educational programs, are provided in appendices at the end of each chapter.

Institutional effectiveness of REDD+ MRV: Countries progress in implementing technical guidelines and good governance requirements

NARCIS (Netherlands)

Ochieng, R.M.; Visseren-Hamakers, Ingrid; Arts, B.; Brockhaus, M.; Herold, M.

2016-01-01

The UNFCCC requires REDD+ countries wishing to receive results-based payments to measure, report and verify (MRV) REDD+ impacts; and outlines technical guidelines and good governance requirements for MRV. This article examines institutional effectiveness of REDD+ MRV by assessing countries’ progress

Geothermal direct-heat utilization assistance. Quarterly project progress report, April--June 1993

Energy Technology Data Exchange (ETDEWEB)

Lienau, P.

1993-06-01

Technical assistance was provided to 60 requests from 19 states. R&D progress is reported on: evaluation of lineshaft turbine pump problems, geothermal district heating marketing strategy, and greenhouse peaking analysis. Two presentations and one tour were conducted, and three technical papers were prepared. The Geothermal Progress Monitor reported: USGS Forum on Mineral Resources, Renewable Energy Tax Credits Not Working as Congress Intended, Geothermal Industry Tells House Panel, Newberry Pilot Project, and Low-Temperature Geothermal Resources in Nevada.

Index to Nuclear Safety: a technical progress review by chrology, permuted title, and author, Volume 11(1) through Volume 20(6)

Energy Technology Data Exchange (ETDEWEB)

Cottrell, W B; Passiakos, M

1980-06-01

This index to Nuclear Safety, a bimonthly technical progress review, covers articles published in Nuclear Safety, Volume II, No. 1 (January-February 1970), through Volume 20, No. 6 (November-December 1979). It is divided into three sections: a chronological list of articles (including abstracts) followed by a permuted-title (KWIC) index and an author index. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center (NSIC), covers all safety aspects of nuclear power reactors and associated facilities. Over 600 technical articles published in Nuclear Safety in the last ten years are listed in this index.

Nonequilibrium photochemical reactions induced by lasers. Technical progress report

International Nuclear Information System (INIS)

Steinfeld, J.I.

1978-04-01

Research has progressed in six principal subject areas of interest to DOE advanced (laser) isotope separation efforts. These are (1) Infrared double resonance spectroscopy of molecules excited by multiple infrared photon absorption, particularly SF 6 and vinyl chloride. (2) Infrared multiphoton excitation of metastable triplet-state molecules, e.g., biacetyl. (3) An Information Theory analysis of multiphoton excitation and collisional deactivation has been carried out. (4) The mechanism of infrared energy deposition and multiphoton-induced reactions in chlorinated ethylene derivatives; and RRKM (statistical) model accounts for all observed behavior of the system, and a deuterium-specific reaction pathway has been identified. (5) Diffusion-enhanced laser isotope separation in N 16 O/N 18 O. (6) A technical evaluation of laser-induced chemistry and isotope separation

Projects at the component development and integration facility. Quarterly technical progress report, April 1, 1994--June 30, 1994

International Nuclear Information System (INIS)

1994-01-01

This quarterly technical progress report presents progress on the projects at the Component Development and Integration Facility (CDIF) during the third quarter of FY94. The CDIF is a major Department of Energy test facility in Butte, Montana, operated by MSE, Inc. Projects in progress include: Biomass Remediation Project; Heavy Metal-Contaminated Soil Project; MHD Shutdown; Mine Waste Technology Pilot Program; Plasma Projects; Resource Recovery Project; and Spray Casting Project

Technical Progress Report

International Nuclear Information System (INIS)

Engelhardt, G.R.; MacDonald, D.D.

1999-01-01

During the past quartile (two month period) most attention has been concentrated on the problem of definition critical temperature at which ''wet'' corrosion first became operable. It has been shown that, in principle, ''wet'' corrosion processes can not be ignored for Yucca Mountain, even for initial times, when the temperature of the surface of containers is well above the boiling temperature of water for the prevailing conditions. This is because the surfaces are covered by highly hydrophilic oxides (e.g. Fe 2 O 3 , NiO, Cr 2 O 3 ) that will hydrate to the form of corresponding hydroxides, which are proton conductors, at least when in the ''wet'' condition. Because proton conduction and the presence of ''bound'' water are all that are required for the external environment to support metallic corrosion in either its general or localized form. Thus, the temperature of dehydration of the hydroxide, e.g. M(OH) 2 → MO + H 2 O(g), is a better criterion for the upper temperature limit for ''wet'' corrosion than is the boiling temperature of ''bulk'' water. During this first task, we have reviewed the existing thermodynamic data base for the dehydration of metal hydroxides and analytical expressions have been developed that allow the upper temperature limit to be estimated

The Impacts of Technical Progress on Sulfur Dioxide Kuznets Curve in China: A Spatial Panel Data Approach

Directory of Open Access Journals (Sweden)

Zhimin Zhou

2017-04-01

Full Text Available This paper aims to reveal the nexus for sulfur dioxide (SO2 emission and income, as well as the effects of technical progress on SO2 emission in China based on environment Kuznets curve (EKC hypothesis. The spatial panel technique is used in case the coefficient estimates are biased due to the negligence of spatial dependence. With the provincial panel data of China from 2004 to 2014, this is the first research that finds an inverse N-trajectory of the relationship between SO2 emission and economic growth and confirms the beneficial impacts of technical advancement on SO2 emission abatement. The empirical results also suggest that the industrial structure change is an important driving force of the SO2 EKC. In addition, the direct and spillover effects of determinants on sulfur emission are clarified and estimated by a correct approach. Finally, we check the stability of our conclusions on the EKC shape for SO2 and technical progress effects when controlling for different variables and specifications, through which we find the turning points are sensitive to variables selections.

Technical progress and climatic change

International Nuclear Information System (INIS)

Ausubel, J.H.

1995-01-01

The global warming debate has neglected and thus underestimated the importance of technical change in considering reduction in greenhouse gases and adaptation to climate change. Relevant quantitative cases of long-run technical change during the past 100 years are presented in computing, communications, transport, energy, and agriculture. A noteworthy technological trajectory is that of decarbonization, or decreasing carbon intensity of primary energy. If human societies have not yet reached the end of the history of technology, the cost structure for mitigation and adaptation changes could be cheap. (Author)

Proceedings of the Second Noncontact Temperature Measurement Workshop

Science.gov (United States)

Hale, Robert R. (Editor)

1989-01-01

The state of the art in noncontact temperature measurement (NCTM) technology was reviewed and the NCTM requirements of microgravity materials processing community identified. The workshop included technical presentations and discussions which ranged from research on advanced concepts for temperature measurement to laboratory research and development regarding measurement principles and state-of-the-art engineering practices for NCTM methodology in commercial and industrial applications. Technical presentations were made concerning: NCTM needs as perceived by several NASA centers, recent ground-based NCT, research and development of industry, NASA, academia, and selected national laboratories, work-in-progress communication, and technical issues of the implementation of temperature measurement in the space environment to facilitate future U.S. materials science investigations.

Deep Trek High Temperature Electronics Project

Energy Technology Data Exchange (ETDEWEB)

Bruce Ohme

2007-07-31

This report summarizes technical progress achieved during the cooperative research agreement between Honeywell and U.S. Department of Energy to develop high-temperature electronics. Objects of this development included Silicon-on-Insulator (SOI) wafer process development for high temperature, supporting design tools and libraries, and high temperature integrated circuit component development including FPGA, EEPROM, high-resolution A-to-D converter, and a precision amplifier.

Western Research Institute: Annual technical progress report, October 1987--September 1988

Energy Technology Data Exchange (ETDEWEB)

1988-12-01

This report describes the technical progress made by the Western Research Institute of the University of Wyoming Research Institute of the University of Wyoming Research Corporation on work performed for the period October 1, 1987 through September 30, 1988. This research involves five resource areas: oil shale, tar sand, underground coal gasification, advanced process technology, and advanced fuels research. Under the terms of the cooperative agreement, an annual project plan has been approved by DOE. The work reported herein reflects the implementation of the research in the plan and follows the structure used therein. 49 refs., 32 figs., 87 tabs.

Technical meeting on progress in managing, and limiting the consequences of events exceeding the design basis

International Nuclear Information System (INIS)

Fabian, H.

2004-01-01

The Technical Groups on 'Reactor Safety' and 'Thermodynamics and Fluid Dynamics' of the Kerntechnische Gesellschaft e.V. organized a joint technical meeting on 'Progress in Managing, and Limiting the Consequences of, Events Exceeding the Design Basis' at the FTU Training Center of the Karlsruhe Research Center. The topic chosen, the papers presented, the presenters, and the non-technical part of the program met with lively interest on the part of institutions in the nuclear field. These were the objectives of the technical meeting: - Establishing a forum for communicating relevant topics. - In-depth discussion of the main topic, i.e. the advanced development of reactor safety, research in the field, and its application, in twenty selected papers presented by speakers from different institutions. - Presentation of topical work in a nuclear technology institution, the Karlsruhe Research Center. (orig.) [de

Studies in theoretical high energy particle physics: Technical progress report [February 1987-February 1988

International Nuclear Information System (INIS)

Sukhatme, U.P.; Keung, Wai-Yee; Kovacs, E.

1988-02-01

This is a technical progress report for grant No. FG02-84ER40173 for the period February 1987 to February 1988. Our research on supersymmetric quantum mechanics has yielded many interesting results. In particular, a systematic approach to the tunneling problem in double well potentials has been developed. Higgs boson related physics at the high energy hadron colliders has been extensively studied

Fundamental studies of separation processes. Technical progress report

International Nuclear Information System (INIS)

Rogers, L.B.

1975-06-01

Studies using high-precision gas chromatography and supercritical fluid chromatography have produced new types of information on liquid crystals and on behavior of substances in the region of the critical temperature, respectively. In addition, the first successful studies of the effects of pressure on cation exchange have been made using aqueous solutions of alkali metal nitrates. In contrast, progress on separations of isotopic species using gas chromatography has been disappointing. In that area, the chief accomplishment has been a determination of the levels of accuracy and precision with which isotopic abundances can be measured using our quadrupole mass spectrometer. (U.S.)

The role of technical progress in the process of recalculating oil reserves; Le role du progres technique dans le processus de renouvellement des reserves petrolieres

Energy Technology Data Exchange (ETDEWEB)

Boulard, J.N. [Total/Fina/Institut Francais du Petrole (IFP), 92 - Rueil-Malmaison (France)

1999-08-01

Contrary to the concept of resources (which is essentially a geological one), the notion of reserves designates the quantities that are technically and economically recoverable. Beyond the production-related effect, the reserves therefore evolve over time in accordance with numerous technical and economic parameters. Among these parameters, it can be seen that technical progress plays a considerable role throughout the process of converting resources into reserves, including progress in the identification, accessibility and processing of the resources, and improvements in economic viability. After having tackled the problem of measuring the 'technical progress effects' and citing examples, we demonstrate that the evolution in oil reserves is subject to three types of impact. These are a quantitative impact by significantly improving the recovery rates or making it possible to identify hitherto undetectable oil fields, a qualitative impact by widening the resource base thanks to the adoption of new categories of oil (in particular the so-called 'unconventional' oils) and by carrying out the gradual substitution between these resources of differing qualities. There is also a dynamic impact, through the acceleration of resource availability. Through these three approaches, technical progress makes makes it possible to ensure continuity in oil supply and contributes significantly to the recalculation of reserves. It therefore acts as a compensating factor, counterbalancing the progressive depletion of resources. (author)

High critical temperature superconductors: Progress achieved after two years

International Nuclear Information System (INIS)

Maillard, J.M.; Rammal, R.; Vittorge, M.C.

1989-01-01

Progress concerning the theory of high temperature superconductors and activity of laboratories of the CNRS (France) are reviewed and news on strategy, budgets, theoretical research, materials characterization, fabrication process technology transfers, commercialisation, uses and data bases are given [fr

Amarillo National Resource Center for Plutonium. Quarterly technical progress report, May 1--July 31, 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-01

Progress is reported on research projects related to the following: Electronic resource library; Environment, safety, and health; Communication, education, training, and community involvement; Nuclear and other materials; and Reporting, evaluation, monitoring, and administration. Technical studies investigate remedial action of high explosives-contaminated lands, radioactive waste management, nondestructive assay methods, and plutonium processing, handling, and storage.

Experimental determination of the temperature dependence of metallic work functions at low temperatures. Progress report

International Nuclear Information System (INIS)

Pipes, P.B.

1977-01-01

Progress made under ERDA Contract No. EY-76-S-02-2314.002 is described. Efforts to gain theoretical insight into the temperature dependence of the contact potential of Nb near the superconducting transition have only been qualitatively successful. Preliminary measurements of adsorbed 4 He gas on the temperature dependence of the contact potentials of metals were performed and compared with a previously developed theory

Surgical resident technical skill self-evaluation: increased precision with training progression.

Science.gov (United States)

Quick, Jacob A; Kudav, Vishal; Doty, Jennifer; Crane, Megan; Bukoski, Alex D; Bennett, Bethany J; Barnes, Stephen L

2017-10-01

Surgical resident ability to accurately evaluate one's own skill level is an important part of educational growth. We aimed to determine if differences exist between self and observer technical skill evaluation of surgical residents performing a single procedure. We prospectively enrolled 14 categorical general surgery residents (six post-graduate year [PGY] 1-2, three PGY 3, and five PGY 4-5). Over a 6-month period, following each laparoscopic cholecystectomy, residents and seven faculty each completed the Objective Structured Assessment of Technical Skills (OSATS). Spearman's coefficient was calculated for three groups: senior (PGY 4-5), PGY3, and junior (PGY 1-2). Rho (ρ) values greater than 0.8 were considered well correlated. Of the 125 paired assessments (resident-faculty each evaluating the same case), 58 were completed for senior residents, 54 for PGY3 residents, and 13 for junior residents. Using the mean from all OSATS categories, trainee self-evaluations correlated well to faculty (senior ρ 0.97, PGY3 ρ 0.9, junior ρ 0.9). When specific OSATS categories were analyzed, junior residents exhibited poor correlation in categories of respect for tissue (ρ -0.5), instrument handling (ρ 0.71), operative flow (ρ 0.41), use of assistants (ρ 0.05), procedural knowledge (ρ 0.32), and overall comfort with the procedure (ρ 0.73). PGY3 residents lacked correlation in two OSATS categories, operative flow (ρ 0.7) and procedural knowledge (ρ 0.2). Senior resident self-evaluations exhibited strong correlations to observers in all areas. Surgical residents improve technical skill self-awareness with progressive training. Less-experienced trainees have a tendency to over-or-underestimate technical skill. Copyright © 2017 Elsevier Inc. All rights reserved.

Research on Evaluation Methodology for High Temperature Components and Technical Issues

International Nuclear Information System (INIS)

Kim, Y.J.; Han, S.B.

2007-03-01

The research on evaluation methodology for high temperature components and technical issues includes the comparison of evaluation technology of Very High Temperature Reactors(VHTRs) with that of present commercial reactors, the review of Hot Gas Duct(HGD) insulation designs, the analysis of the codes related to VHTR component construction and the analysis of technical issues on application of present codes to HGD construction. Codes to assure the integrity of the VHTR components are not fully prepared yet in any country. To understand the evaluation technology of the VHTR-related codes, key requirements of ASME B and PV Code Section III, Subsection NB and NH were compared. Six kinds of HGD designs were reviewed and compared. A reference which analyzed seven kinds of present component codes were reviewed and the limitations of them were summarized. Especially it was found that the selection of materials is limited, material property data are not enough, and design analysis methodology is not fully specified

Productivity Change, Technical Progress, and Relative Efficiency Change in the Public Accounting Industry

OpenAIRE

Rajiv D. Banker; Hsihui Chang; Ram Natarajan

2005-01-01

We present evidence on components of productivity change in the public accounting industry toward the end of the 20th century. Using revenue and human resource data from 64 of the 100 largest public accounting firms in the United States for the 1995--1999 period, we analyze productivity change, technical progress, and relative efficiency change over time. The average public accounting firm experienced a productivity growth of 9.5% between 1995 and 1999. We find support for the hypothesis that...

GPHS-RTGs in support of the Cassini RTG Program. Semi annual technical progress report, September 26, 1994--April 2, 1995

International Nuclear Information System (INIS)

1995-01-01

The technical progress achieved during the period 26 September 1994 through 2 April 1995 on Contract DE-AC03-91SF18852 Radioisotope Thermoelectric Generators and Ancillary Activities is described herein. Monthly technical activity for the period 27 February 1995 through 2 April 1995 is included in this progress report. The report addresses tasks, including: spacecraft integration and liaison; engineering support; safety; qualified unicouple production; ETG Fabrication, assembly, and test; ground support equipment; RTG shipping and launch support; designs, reviews, and mission applications; project management, quality assurance, reliability, contract changes, CAGO acquisition (operating funds), and CAGO maintenance and repair; and CAGO acquisition (capital funds)

Technical Assessment of Cryo-Compressed Hydrogen Storage Tank Systems for Automotive Applications

Energy Technology Data Exchange (ETDEWEB)

Ahluwalia, Rajesh [Argonne National Lab. (ANL), Argonne, IL (United States); Hua, T. Q. [Argonne National Lab. (ANL), Argonne, IL (United States); Peng, J. -K. [Argonne National Lab. (ANL), Argonne, IL (United States); Lasher, S. [TIAX LLC, Lexington, MA (United States); McKenney, Kurtis [TIAX LLC, Lexington, MA (United States); Sinha, J. [TIAX LLC, Lexington, MA (United States)

2009-12-01

Technical report describing DOE's second assessment report on a third generation (Gen3) system capable of storing hydrogen at cryogenic temperatures within a pressure vessel on-board a vehicle. The report includes an overview of technical progress to date, including the potential to meet DOE onboard storage targets, as well as independent reviews of system cost and energy analyses of the technology paired with delivery costs.

Works Technical Department progress report, March 1961

Energy Technology Data Exchange (ETDEWEB)

None

1961-04-19

This document details the activities of the Savannah River Works Technical Department during the month of March 1961. Topics discussed are: Reactor Technology, Separations Technology, Engineering Assistance, Health Physics, Laboratories Overview, and Technical Papers Issued.

Novel Multisensor Probe for Monitoring Bladder Temperature During Locoregional Chemohyperthermia for Nonmuscle-Invasive Bladder Cancer: Technical Feasibility Study

Science.gov (United States)

Geijsen, Debby E.; Zum Vörde Sive Vörding, Paul J.; Schooneveldt, Gerben; Sijbrands, Jan; Hulshof, Maarten C.; de la Rosette, Jean; de Reijke, Theo M.; Crezee, Hans

2013-01-01

Abstract Background and Purpose: The effectiveness of locoregional hyperthermia combined with intravesical instillation of mitomycin C to reduce the risk of recurrence and progression of intermediate- and high-risk nonmuscle-invasive bladder cancer is currently investigated in clinical trials. Clinically effective locoregional hyperthermia delivery necessitates adequate thermal dosimetry; thus, optimal thermometry methods are needed to monitor accurately the temperature distribution throughout the bladder wall. The aim of the study was to evaluate the technical feasibility of a novel intravesical device (multi-sensor probe) developed to monitor the local bladder wall temperatures during loco-regional C-HT. Materials and Methods: A multisensor thermocouple probe was designed for deployment in the human bladder, using special sensors to cover the bladder wall in different directions. The deployment of the thermocouples against the bladder wall was evaluated with visual, endoscopic, and CT imaging in bladder phantoms, porcine models, and human bladders obtained from obduction for bladder volumes and different deployment sizes of the probe. Finally, porcine bladders were embedded in a phantom and subjected to locoregional heating to compare probe temperatures with additional thermometry inside and outside the bladder wall. Results: The 7.5 cm thermocouple probe yielded optimal bladder wall contact, adapting to different bladder volumes. Temperature monitoring was shown to be accurate and representative for the actual bladder wall temperature. Conclusions: Use of this novel multisensor probe could yield a more accurate monitoring of the bladder wall temperature during locoregional chemohyperthermia. PMID:24112045

TECHNICAL COORDINATION

CERN Multimedia

Austin Ball

2013-01-01

  Since the last report, much visible progress has been made, as the LS1 programme approaches the halfway point. From early October, technical and safety shift-crew have been present around the clock, allowing detectors to stay switched on overnight, ensuring that safety systems are operational and instructions for non-expert shift-crew are clear. LS1 progress Throughout the summer, whilst the solenoid vacuum tank and YB0 surfaces were accessible, an extensive installation programme took place to prepare for Tracker colder operation and the PLT installation, in 2014, the Phase 1 Pixel Tracker installation, in 2016–’17, and the HCAL Phase 1 upgrade completion, ending in LS2. This included pipework for N2 or dry air to flush the Tracker bulkhead region, many sensors to monitor temperature and dew point in the Tracker and its service channels, heating wires outside the Tracker cooling bundles, supports for the new vacuum-jacketed, concentric, CO2 Pixel cooling lines, the PLT cool...

GT-MHR COMMERCIALIZATION STUDY TECHNICAL PROGRESS AND COST MANAGEMENT REPORT FOR THE PERIOD AUGUST 1 THROUGH AUGUST 31, 2003

International Nuclear Information System (INIS)

Shenoy, A.S.

2003-01-01

OAK A271 GT-MHR COMERCIALiZATION STUDY TECHNICAL PROGRESS AND COST MANAGEMENT REPORT FOR THE PERIOD AUGUST 1 THROUGH AUGUST 31, 2003. In the process of fabricating the MHR-1 irradiation test capsule, Petten has advised that three thermocouples (out of 24) and the Self Powered Neutron detector were damaged during high temperature brazing with the upper capsule lid. Procurement of new TCs and SPN is in process but there will be a delay in the irradiation test of about nine weeks. Startup of the irradiation is now projected to be July or August 2004. In preparation for performing the nuclear design analysis activities required by the advanced fuel studies task, a complete 3-D nuclear design analysis is first being performed of the GT-MHR reference design. This will serve as the baseline for studies of the advanced fuel nuclear design performance

Nuclear structure theory. Annual technical progress report, October 1, 1976--September 30, 1977

International Nuclear Information System (INIS)

French, J.B.; Koltun, D.S.

1977-01-01

This report summarizes progress during the past year in the following areas of nuclear structure and reaction theory: (1) statistical spectroscopy, including giant resonances for beta and electromagnetic excitation and sum rules (including inverse-energy-weighted sum rules), statistical methods of truncating shell model spaces and renormalization of operators, study of state labelling and ''chains'' of groups, evaluation of fluctuation measures, technical aspects of operator averaging; (2) meson interactions with nuclei, including scattering and absorption of mesons by nuclei (general methods), models for absorption, single- and double-charge exchange of pions, role of rho mesons

FY 1992 work plan and technical progress reports

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-11-01

The Desert Research Institute (DRI) is a division of the University of Nevada System devoted to multidisciplinary scientific research. For more than 25 years, DRI has conducted research for the US Department of Energy`s Nevada Field Office (DOE/NV) in support of operations at the Nevada Test Site (NTS). During that time, the research program has grown from an early focus on hydrologic studies to include the areas of geology, archaeology, environmental compliance and monitoring, statistics, database management, public education, and community relations. The range of DRI`s activities has also expanded to include a considerable amount of management and administrative support in addition to scientific investigations. DRI`s work plan for FY 1992 reflects a changing emphasis in DOE/NV activities from nuclear weapons testing to environmental restoration and monitoring. Most of the environmental projects from FY 1991 are continuing, and several new projects have been added to the Environmental Compliance Program. The Office of Technology Development Program, created during FY 1991, also includes a number of environmental projects. This document contains the FY 1992 work plan and quarterly technical progress reports for each DRI project.

Final Technical Progress Report: Development of Low-Cost Suspension Heliostat; December 7, 2011 - December 6, 2012

Energy Technology Data Exchange (ETDEWEB)

Bender, W.

2013-01-01

Final technical progress report of SunShot Incubator Solaflect Energy. The project succeeded in demonstrating that the Solaflect Suspension Heliostat design is viable for large-scale CSP installations. Canting accuracy is acceptable and is continually improving as Solaflect improves its understanding of this design. Cost reduction initiatives were successful, and there are still many opportunities for further development and further cost reduction.

Progress in DOE high temperature superconductivity electric power applications program

International Nuclear Information System (INIS)

Daley, J.G.; Sheahn, T.P.

1992-01-01

The Department of Energy (DOE) leads national R and D effort to develop US industry's capability to produce a wide range of advanced energy-efficient electric power products. The immediate need is to make high temperature superconductivity (HTS) wire. Wire developers at the DOE National laboratories are working wit industrial partners toward this objective. In this paper, the authors describe the progress to date, citing both the difficulties associated with making wire from these ceramic materials, and achievements at several organizations. Results for progress over the next five years are stated

Generation and focusing of pulsed intense ion beams. Technical progress report, 20 August 1981-30 September 1982

International Nuclear Information System (INIS)

Hammer, D.A.; Kusse, B.R.; Sudan, R.N.

1983-07-01

The progress on this contract is described in two parts. The first deals with the technical operation of the LION accelerator which is the exact equivalent to one line of PBFA-I. The second part is concerned with the experimental results on the ion diode mounted at the front end of the LION accelerator

The U.S. nuclear waste management program - technical progress at Yucca Mountain

Energy Technology Data Exchange (ETDEWEB)

Barrett, L.H. [U.S. Department of Energy (United States)

2001-07-01

This paper discusses the current status of a national program being developed by the U.S. Department of Energy for the management of spent nuclear fuel and high-level radioactive waste produced by civilian nuclear power generation and defense-related activities. In 1987 the U.S. Congress directed the Department to characterize the Yucca Mountain site in Nevada and determine its suitability for development of a geologic repository. This paper will focus on the technical progress that has been made after more than 15 years of scientific and engineering investigations at Yucca Mountain, and the remaining work that is being done to support a decision on whether to recommend the site for development of a geologic repository. (author)

High temperature chemistry. Progress report, 1 November 1974--31 October 1975

International Nuclear Information System (INIS)

Gilles, P.W.

1975-01-01

Activities are described under the topics of education; publications and talks;research progress highlights; space and facilities; level of activity; and miscellaneous. Current research is reported for the high temperature thermodynamics and vaporization of the titanium oxides, the vaporization of the rare-earth borides, the phase studies on the Zr-Nb-O system, the studies on high-molecular weight inorganic species, and the kinetic studies on high-temperature vaporization processes

Theory of high temperature plasmas. Final report

International Nuclear Information System (INIS)

Davidson, R.C.; Liu, C.S.

1977-01-01

This is a report on the technical progress in our analytic studies of high-temperature fusion plasmas. We also emphasize that the research summarized here makes extensive use of computational methods and therefore forms a strong interface with our numerical modeling program which is discussed later in the report

The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Kindergarten. Technical Report # 0921

Science.gov (United States)

Alonzo, Julie; Tindal, Gerald

2009-01-01

In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in kindergarten. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2008 and administered to approximately 2800 students from…

Decontamination Systems Information and Research Program. Quarterly technical progress report, January 1--March 31, 1993

Energy Technology Data Exchange (ETDEWEB)

1993-04-01

This reports reports the progress/efforts performed on six technical projects: 1. systematic assessment of the state of hazardous waste clean-up technologies; 2. site remediation technologies (SRT):drain- enhanced soil flushing for organic contaminants removal; 3. SRT: in situ bio-remediation of organic contaminants; 4. excavation systems for hazardous waste sites: dust control methods for in-situ nuclear waste handling; 5. chemical destruction of polychlorinated biphenyls; and 6. development of organic sensors: monolayer and multilayer self-assembled films for chemical sensors.

GPHS-RTGs in support of the Cassini Mission. Semi annual technical progress report, 1 April 1996--29 September 1996

International Nuclear Information System (INIS)

1996-01-01

This technical progress report discusses work on the Radioisotope Generators and Ancillary Activities for the Cassini spacecraft. The Cassini spacecraft is expected to launch in October 1997, and will explore Saturn and its moons. This progress report discusses issues in: spacecraft integration and liason, engineering support, safety, qualified unicouple fabrication, ETG fabrication and testing, ground support equipment, RTG shipping and launch support, designs, reviews and mission application. Safety analysis of the RTGs during reentry and launch accidents are covered. This report covers the period of April 1 to September 29, 1996

Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. Part 1. Geological environment of Japan

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-11-01

Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the geological disposal concept for high-level radioactive wastes (HLW) in Japan. The present document, the part 1 of the progress report, describes first in detail the role of geological environment in high-level radioactive wastes disposal, the features of Japanese geological environment, and programs to proceed the investigation in geological environment. The following chapter summarizes scientific basis for possible existence of stable geological environment, stable for a long period needed for the HLW disposal in Japan including such natural phenomena as volcano and faults. The results of the investigation of the characteristics of bed-rocks and groundwater are presented. These are important for multiple barrier system construction of deep geological disposal. The report furthermore describes the present status of technical and methodological progress in investigating geological environment and finally on the results of natural analog study in Tono uranium deposits area. (Ohno, S.)

Index to Nuclear Safety: a technical progress review by chronology, permuted title, and author. Vol. 11(1)--Vol. 18(6)

Energy Technology Data Exchange (ETDEWEB)

Cottrell, W.B.; Klein, A.

1978-04-11

This index to Nuclear Safety covers articles published in Nuclear Safety, Vol. 11, No. 1 (January-February 1970), through Vol. 18, No. 6 (November-December 1977). It is divided into three sections: a chronological list of articles (including abstracts) followed by a permuted-title (KWIC) index and an author index. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center (NSIC), covers all safety aspects of nuclear power reactors and associated facilities. Over 450 technical articles published in Nuclear Safety in the last eight years are listed in this index.

Index to Nuclear Safety: a technical progress review by chronology, permuted title, and author. Vol. 11(1)--Vol. 18(6)

International Nuclear Information System (INIS)

Cottrell, W.B.; Klein, A.

1978-01-01

This index to Nuclear Safety covers articles published in Nuclear Safety, Vol. 11, No. 1 (January-February 1970), through Vol. 18, No. 6 (November-December 1977). It is divided into three sections: a chronological list of articles (including abstracts) followed by a permuted-title (KWIC) index and an author index. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center (NSIC), covers all safety aspects of nuclear power reactors and associated facilities. Over 450 technical articles published in Nuclear Safety in the last eight years are listed in this index

The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 1. Technical Report # 0919

Science.gov (United States)

Alonzo, Julie; Tindal, Gerald

2009-01-01

In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grade 1. These measures, available as part of easyCBM [TM], an online progress monitoring assessment system, were developed in 2008 and administered to approximately 2800 students from schools…

The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 2. Technical Report # 0920

Science.gov (United States)

Alonzo, Julie; Lai, Cheng Fei; Tindal, Gerald

2009-01-01

In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 7. Technical Report 0908

Science.gov (United States)

Lai, Cheng Fei; Alonzo, Julie; Tindal, Gerald

2009-01-01

In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. Introductory part and summaries

International Nuclear Information System (INIS)

1999-11-01

Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the geological disposal concept for high-level radioactive wastes (HLW) in Japan and comprises seven chapters. Chapter I briefly describes the importance of HLW management in promoting nuclear energy utilization. According to the long-term program, the HLW separated from spent fuels at reprocessing plants is to be vitrified and stored for a period of 30 to 50 years to allow cooling, then be disposed of in a deep geological formation. Chapter II mainly explains the concepts of geological disposal in Japan. Chapters III to V are devoted to discussions on three important technical elements (the geological environment of Japan, engineering technology and safety assessment of the geological disposal system) which are necessary for reliable realization of the geological disposal concept. Chapter VI demonstrates the technical ground for site selection and for setup of safety standards of the disposal. Chapter VII summarizes together with plans for future research and development. (Ohno, S.)

Progresso tecnico, forme di mercato e disoccupazione. ( Technical progress, market forms and unemployment

Directory of Open Access Journals (Sweden)

A. ASIMAKOPULOS A.

2013-12-01

Full Text Available Lo scopo del presente lavoro è triplice . Il primo obiettivo è quello di sottolineare l'importanza delle intuizioni da trovare nel lavoro di Sylos Labini . Il secondo scopo è quello di espandere su di essa distinguendo tra i diversi tipi di progresso tecnico . Infine , il terzo obiettivo è quello di commentare il confronto di Labini di Ricardo e Keynes sulla possibilità di disoccupazione tecnologica . Per quanto riguarda la sua descrizione del progresso tecnologico come " risparmio di lavoro " , l'autore mostra che una descrizione più completa sarebbe più utile per i suoi scopiThe purpose of the present paper is threefold. The first purpose is to emphasise the importance of the insights to be found in Sylos Labini’s work. The second purpose is to expand upon it by distinguishing  between the different types of technical progress. Finally, the third purpose is to comment on Labini’s comparison of Ricardo and Keynes on the possibility of technological unemployment. Regarding his description of technological progress as “labour saving”, the author shows that a more comprehensive description would be more useful for his purposes.JEL: E24, J64, O33

Technical progress and efficiency changes in football teams participating in the UEFA Champions League

Directory of Open Access Journals (Sweden)

Lucía Isabel García Cebrián

2015-09-01

Full Text Available This paper commits to calculate and analyze productivy levels and its components for teams that participated in the UEFA Champions League between 2003 and 2012. It will pursue three objectives: 1 evaluate resources usage, 2 analyze the productivity levels of the football teams and the sports results, and 3 see the influence of participation experience in reference to productivity and sports results. Using Malmquist Productivity Index, the results reflect a lack of consistent progression of efficiency, productivity, and technical change. This competition does not reward the efficient usage of resources and there is not a conclusive relationshop between permanence in the competition and productivity.

Volatiles combustion in fluidized beds. Technical progress report, 4 March 1993--3 June 1993

Energy Technology Data Exchange (ETDEWEB)

Hesketh, R.P.

1993-09-01

The goal of this project is to investigate the conditions in which volatiles will burn within both the dense and freeboard regions of fluidized beds. Experiments using a fluidized bed operated at incipient fluidization will be performed to characterize the effect of particle surface area, initial fuel concentration, and particle type on the inhibition of volatiles within a fluidized bed. The work conducted during the period 4 March, 1993 through 3 June, 1993 is reported in this technical progress report. The work during this time period consists primarily of the startup and trouble shooting of the fluidized bed reactor and gas phase modeling of methane and propane.

The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 3. Technical Report # 09-02

Science.gov (United States)

Alonzo, Julie; Lai, Cheng Fei; Tindal, Gerald

2009-01-01

In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 5. Technical Report # 09-01

Science.gov (United States)

Lai, Cheng Fei; Alonzo, Julie; Tindal, Gerald

2009-01-01

In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 4. Technical Report # 09-03

Science.gov (United States)

Alonzo, Julie; Lai, Cheng Fei; Tindal, Gerald

2009-01-01

In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 8. Technical Report # 09-04

Science.gov (United States)

Lai, Cheng Fei; Alonzo, Julie; Tindal, Gerald

2009-01-01

In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

National Council on Radiation Protection and Measurements semiannual technical progress report, March 1989--August 1989

International Nuclear Information System (INIS)

Ney, W.R.

1991-01-01

This semiannual technical progress report is for the period 1 March 1989 through 31 August 1989. This National Council on Radiation Protection and Measurements (NCRP) program is designed to provide recommendations for radiation protection based on scientific principles. During this period several reports were published covering the topics of occupational radiation exposure, medical exposure, radon control, dosimetry, and radiation protection standards. Accomplishments of various committees are also reported; including the committees on dental x-ray protection, radiation safety in uranium mining and milling, ALARA, instrumentation, records maintenance, occupational exposures of medical personnel, emergency planning, and others. (SM)

Index to Nuclear Safety: a technical progress review by chronology, permuted title, and author, Volume 18 (1) through Volume 22 (6)

International Nuclear Information System (INIS)

Cottrell, W.B.; Passiakos, M.

1982-06-01

This index to Nuclear Safety covers articles published in Nuclear Safety, Volume 18, Number 1 (January-February 1977) through Volume 22, Number 6 (November-December 1981). The index is divided into three section: a chronological list of articles (including abstracts), a permuted-title (KWIC) index, and an author index. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center, covers all safety aspects of nuclear power reactors and associated facilities. Over 300 technical articles published in Nuclear Safety in the last 5 years are listed in this index

Index to Nuclear Safety: a technical progress review by chronology, permuted title, and author, Volume 18 (1) through Volume 22 (6)

Energy Technology Data Exchange (ETDEWEB)

Cottrell, W.B.; Passiakos, M.

1982-06-01

This index to Nuclear Safety covers articles published in Nuclear Safety, Volume 18, Number 1 (January-February 1977) through Volume 22, Number 6 (November-December 1981). The index is divided into three section: a chronological list of articles (including abstracts), a permuted-title (KWIC) index, and an author index. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center, covers all safety aspects of nuclear power reactors and associated facilities. Over 300 technical articles published in Nuclear Safety in the last 5 years are listed in this index.

Association Euratom - DTU, Technical University of Denmark, Department of Physics - Annual Progress Report 2011

DEFF Research Database (Denmark)

The programme of the Research Unit of the Fusion Association Euratom – DTU, Technical University of Denmark (until 31-12- 2011: Association Euratom – Risø DTU) covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport...... temperature superconductors. Other activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2011....

Index to Nuclear Safety. A technical progress review by chronology, permuted title, and author. Vol. 11, No. 1--Vol. 17, No. 6

International Nuclear Information System (INIS)

Cottrell, W.B.; Klein, A.

1977-01-01

This index to Nuclear Safety covers articles in Nuclear Safety Vol. 11, No. 1 (Jan.-Feb. 1970), through Vol. 17, No. 6 (Nov.-Dec. 1976). The index includes a chronological list of articles (including abstract) followed by KWIC and Author Indexes. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center, covers all safety aspects of nuclear power reactors and associated facilities. The index lists over 350 technical articles in the last six years of publication

Index to Nuclear Safety. A technical progress review by chronology, permuted title, and author. Vol. 11, No. 1--Vol. 17, No. 6

Energy Technology Data Exchange (ETDEWEB)

Cottrell, W.B.; Klein, A.

1977-02-23

This index to Nuclear Safety covers articles in Nuclear Safety Vol. 11, No. 1 (Jan.-Feb. 1970), through Vol. 17, No. 6 (Nov.-Dec. 1976). The index includes a chronological list of articles (including abstract) followed by KWIC and Author Indexes. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center, covers all safety aspects of nuclear power reactors and associated facilities. The index lists over 350 technical articles in the last six years of publication.

Nuclear structure theory. Technical progress report, September 1, 1982-August 31, 1984

International Nuclear Information System (INIS)

French, J.B.; Koltun, D.S.

1984-01-01

Research progress is reported. Spectral Averaging studies are outlined including the theory of level densities for interacting nucleons, the properties of single-particle nuclear excitations, spectral distributions for fixed symmetries, and applications to the secular behavior of fluctuation measures in complex nuclei. Collective States research is described, in particular the boson-fermion symmetries which are related to the U(5) limit of the interacting boson model. Nuclear Reaction studies are described including the statistical theory of pion absorption, direct reactions at intermediate energies, and the properties of the off-shell πN t-matrix. Progress is reported on the quark theory of nuclear matter and the construction of models for a Fermi fluid which, near the nuclear ground state, is a fluid of nucleons composed of quarks, and, at high densities or temperatures, is a quark fluid. Applications of formal scattering theory to the study of phase-conjugate optics are discussed. Publications are listed

Progress report : Technical Physics Division

International Nuclear Information System (INIS)

Gopalaraman, C.P.; Deshpande, R.Y.

1978-01-01

The research and development work carried out in the Technical Physics Division of the Bhabha Atomic Research Centre, Bombay, is reported. Some of the achievements are: (1) fabrication of mass spectrometers for heavy water analysis and lithium 6/7 isotope ratio measurement, (2) fabrication of electronic components for mass spectrometers, (3) growing of sodium iodide crystals for radiation detectors, (4) development of sandwich detectors comprising of NaI(Tl) and CaI(Na), (5) fabrication of mass spectrometer type leak detectors and (6) fabrication of the high vacuum components of the vacuum system of the variable energy cyclotron based at Calcutta. (M.G.B.)

Investigations of the reactivity temperature coefficient of the Dresden Technical University training and research reactor

International Nuclear Information System (INIS)

Adam, E.; Knorr, J.

1982-01-01

Approximate formulas are derived for determining the temperature coefficient of reactivity of the training and research reactor (AKR) of the Dresden Technical University. Values calculated on the basis of these approximations show good agreement with experimentally obtained results, thus confirming the applicability of the formulas to simple systems

Solar lease grant program. Technical progress report

Energy Technology Data Exchange (ETDEWEB)

1981-04-01

Progress on a lease program for the installation of a solar water heater with no installation charge is reported. Information on the announcement of the program, the selection of participants, the contractural agreement, progress on installation of equipment, monitoring, and evaluation is summarized. The status of the budget concerned with the program is announced. Forms used for applications for the program and an announcement from Resource Alternatives for Cilco customers are presented.

Progress in understanding the mechanical behavior of pressure-vessel materials at elevated temperatures

International Nuclear Information System (INIS)

Swindeman, R.W.; Brinkman, C.R.

1981-01-01

Progress during the 1970's on the production of high-temperature mechanical properties data for pressure vessel materials was reviewed. The direction of the research was toward satisfying new data requirements to implement advances in high-temperature inelastic design methods. To meet these needs, servo-controlled testing machines and high-resolution extensometry were developed to gain more information on the essential behavioral features of high-temperature alloys. The similarities and differences in the mechanical response of various pressure vessel materials were identified. High-temperature pressure vessel materials that have received the most attention included Type 304 stainless steel, Type 316 stainless steel, 2 1/4 Cr-1 Mo steel, alloy 800H, and Hastelloy X

Technical progress report

International Nuclear Information System (INIS)

1996-01-01

This report summarizes experimental and theoretical work in basic nuclear physics carried out between October 1, 1995, the closing of our last Progress Report, and September 30, 1996 at the Nuclear Physics Laboratory of the University of Colorado, Boulder, under contracts DE-FG03-93ER-40774 and DE-FG03-95ER-40913 with the United States Department of Energy. The experimental contract supports broadly-based experimental research in intermediate energy nuclear physics. This report includes results from studies of Elementary Systems involving the study of the structure of the nucleon via polarized high-energy positron scattering (the HERMES experiment) and lower energy pion scattering from both polarized and unpolarized nucleon targets. Results from pion- and kaon-induced reactions in a variety of nuclear systems are reported under the section heading Meson Reactions; the impact of these and other results on understanding the nucleus is presented in the Nuclear Structure section. In addition, new results from scattering of high-energy electrons (from CEBAF/TJNAF) and pions (from KEK) from a broad range of nuclei are reported in the section on Incoherent Reactions. Finally, the development and performance of detectors produced by the laboratory are described in the section titled Instrumentation

A systematic assessment of the state of hazardous waste clean-up technologies. Quarterly technical progress report, April 1--June 30, 1993

Energy Technology Data Exchange (ETDEWEB)

Berg, M.T.; Reed, B.E.; Gabr, M.

1993-07-01

West Virginia University (WVU) and the US DOE Morgantown Energy Technology Center (METC) entered into a Cooperative Agreement on August 29, 1992 entitled ``Decontamination Systems Information and Research Programs.`` Stipulated within the Agreement is the requirement that WVU submit to METC a series of Technical Progress Report for Year 1 of the Agreement. This report reflects the progress and/or efforts performed on the following nine technical projects encompassed by the Year 1 Agreement for the period of April 1 through June 30, 1993: Systematic assessment of the state of hazardous waste clean-up technologies; site remediation technologies -- drain-enhanced soil flushing (DESF) for organic contaminants removal; site remediation technologies -- in situ bioremediation of organic contaminants; excavation systems for hazardous waste sites; chemical destruction of polychlorinated biphenyls; development of organic sensors -- monolayer and multilayer self-assembled films for chemical sensors; Winfield lock and dam remediation; Assessments of Technologies for hazardous waste site remediation -- non-treatment technologies and pilot scale test facility implementation; and remediation of hazardous sites with stream reforming.

High critical temperature superconductors: Progress achieved after two years. Les supraconducteurs haute temperature critique: L'etat des lieux deux ans apres

Energy Technology Data Exchange (ETDEWEB)

Maillard, J M; Rammal, R; Vittorge, M C

1989-01-01

Progress concerning the theory of high temperature superconductors and activity of laboratories of the CNRS (France) are reviewed and news on strategy, budgets, theoretical research, materials characterization, fabrication process technology transfers, commercialisation, uses and data bases are given.

GT-MHR COMMERCIALZATION STUDY. TECHNICAL PROGRESS AND COST MANAGEMENT REPORT FOR THE PERIOD MAY 1 THROUGH MAY 31, 2003

International Nuclear Information System (INIS)

SHENOY, A.S.

2003-01-01

A271 GT-MHR COMMERCIALZATION STUDY TECHNICAL PROGRESS AND COST MANAGEMENT REPORT FOR THE PERIOD MAY 1 THROUGH MAY 31, 2003. Petten advised GA the start of the HFR-EU2 irradiation is being delayed until late July 2004. HFR-EU1 (pebble fuel) is also delayed until February/March 2004. The reason for the delays was implementation of new financial regulations at Petten that delayed the contracts for capsule fabrication. Review of the MHR-2 Fuel Product Specification was completed. Revision of the specification to incorporate the review results is in progress. Detailed test matrices have been drafted for capsule irradiation tests and for post-irradiation heating tests proposed for development and qualification of advanced coated-particle fuels capable of meeting anticipated VHTR fuel performance requirements

Index to Nuclear Safety. A technical progress review by chronology, permuted title, and author. Vol 11, No. 1 through Vol. 16, No. 6

International Nuclear Information System (INIS)

Cottrell, W.B.; Klein, A.

1976-04-01

This index to Nuclear Safety covers articles in Nuclear Safety Vol. 11, No. 1 (Jan.-Feb. 1970) through Vol. 16, No. 6 (Nov.-Dec. 1975). Included in the index is a chronological list of articles (including abstract) followed by both a KWIC index and an Author Index. Nuclear Safety is a bimonthly technical progress review prepared by the Nuclear Safety Information Center and covers all safety aspects of nuclear power reactors and associated facilities. The index lists over 300 technical articles in the last six years of publication

Index to Nuclear Safety. A technical progress review by chronology, permuted title, and author. Vol 11, No. 1 through Vol. 16, No. 6

Energy Technology Data Exchange (ETDEWEB)

Cottrell, W.B.; Klein, A.

1976-04-01

This index to Nuclear Safety covers articles in Nuclear Safety Vol. 11, No. 1 (Jan.-Feb. 1970) through Vol. 16, No. 6 (Nov.-Dec. 1975). Included in the index is a chronological list of articles (including abstract) followed by both a KWIC index and an Author Index. Nuclear Safety is a bimonthly technical progress review prepared by the Nuclear Safety Information Center and covers all safety aspects of nuclear power reactors and associated facilities. The index lists over 300 technical articles in the last six years of publication.

Urology technical and non-technical skills development: the emerging role of simulation.

Science.gov (United States)

Rashid, Prem; Gianduzzo, Troy R J

2016-04-01

To review the emerging role of technical and non-technical simulation in urological education and training. A review was conducted to examine the current role of simulation in urology training. A PUBMED search of the terms 'urology training', 'urology simulation' and 'urology education' revealed 11,504 titles. Three hundred and fifty-seven abstracts were identified as English language, peer reviewed papers pertaining to the role of simulation in urology and related topics. Key papers were used to explore themes. Some cross-referenced papers were also included. There is an ongoing need to ensure that training time is efficiently utilised while ensuring that optimal technical and non-technical skills are achieved. Changing working conditions and the need to minimise patient harm by inadvertent errors must be taken into account. Simulation models for specific technical aspects have been the mainstay of graduated step-wise low and high fidelity training. Whole scenario environments as well as non-technical aspects can be slowly incorporated into the curriculum. Doing so should also help define what have been challenging competencies to teach and evaluate. Dedicated time, resources and trainer up-skilling are important. Concurrent studies are needed to help evaluate the effectiveness of introducing step-wise simulation for technical and non-technical competencies. Simulation based learning remains the best avenue of progressing surgical education. Technical and non-technical simulation could be used in the selection process. There are good economic, logistic and safety reasons to pursue the process of ongoing development of simulation co-curricula. While the role of simulation is assured, its progress will depend on a structured program that takes advantage of what can be delivered via this medium. Overall, simulation can be developed further for urological training programs to encompass technical and non-technical skill development at all stages, including

Power systems development facility. Quarterly technical progress report, January 1, 1994--March 31, 1994

Energy Technology Data Exchange (ETDEWEB)

1994-07-01

This quarterly technical progress report summarizes work completed during the last quarter of the Second Budget Period, January 1 through March 31, 1994, entitled {open_quotes}Hot Gas Cleanup Test Facility for Gasification and Pressurized Combustion.{close_quotes} The objective of this project is to evaluate hot gas particulate control technologies using coal-derived gas streams. This will entail the design, construction, installation, and use of a flexible test facility which can operate under realistic gasification and combustion conditions. The major particulate control device issues to be addressed include the integration of the particulate control devices into coal utilization systems, on-line cleaning techniques, chemical and thermal degradation of components, fatigue or structural failures, blinding, collection efficiency as a function of particle size, and scale-up of particulate control systems to commercial size.

Geothermal direct-heat utilization assistance: Federal assistance program. Quarterly project progress report, October--December 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

The report summarizes geothermal technical assistance, R&D and technology transfer activities of the Geo-Heat Center at Oregon Institute of Technology for the first quarter of FY-96. It describes 90 contacts with parties during this period related to technical assistance with geothermal direct heat projects. Areas dealt with include geothermal heat pumps, space heating, greenhouses, aquaculture, equipment and resources. Research activities are summarized on low-temperature resource assessment, geothermal district heating system cost evaluation and silica waste utilization project. Outreach activities include the publication of a geothermal direct use Bulletin, dissemination of information, geothermal library, technical papers and seminars, development of a webpage, and progress monitor reports on geothermal resources and utilization.

48 CFR 742.1170-4 - Progress reporting requirements and contract clause.

Science.gov (United States)

2010-10-01

... progress. (b) Because the cognizant technical officer is the individual most familiar with the contractor's performance, the contractor must submit the progress reports directly to the cognizant technical officer. The cognizant technical officer must review the reports and advise the contracting officer, in writing, of any...

Nuclear structure theory. Annual technical progress report, July 1, 1975--September 30, 1976

International Nuclear Information System (INIS)

French, J.B.; Koltun, D.S.

1976-01-01

This report summarizes progress during the past year in the following areas of nuclear structure and reaction theory: Meson interactions with nucleons and nuclei, including elastic and inelastic scattering of pions, three-body theories of scattering and absorption of pions by deuterons, π-p bremsstrahlung, and multiple-excitation models for meson absorption by heavier nuclei. Studies of the inverse scattering problem including 1 S 0 nucleon-nucleon scattering; the relativistic two-body problem, particularly for relativistic effects at low energies: the unitary-pole expansion in nucleon-nucleon scattering with hard-core interactions. Statistical spectroscopy including: strength distributions and sum rules(both energy weighted and inverse energy weighted) for nuclear excitations; fluctuations and correlations in spectra, strengths and expectation values; studies of Garvey-Kelson and similar mass relationships; spectroscopy in huge spaces including spectral methods for renormalization of the interaction and for using (two + three)-body Skyrme interactions; technical aspects of operator averaging

Nuclear waste glass melter: an update of technical progress

International Nuclear Information System (INIS)

Brouns, R.A.; Hanson, M.S.

1984-08-01

The direct slurry-fed ceramic-lined melter is currently the reference US process for treating defense and civilian high-level liquid waste. Extensive nonradioactive pilot-scale testing at Pacific Northwest Laboratory (PNL) and Savannah River Laboratory has proven the process, defined operating parameters, and identified successful equipment design concepts. Programs at PNL continue to support several of the planned US vitrification plants through preparation of equipment designs and flowsheet testing. Current emphasis is on remotization of equipment, radioactive verification testing, and resolution of remaining technical issues. Development of this technology, technical status, and planned development activities are discussed. 9 references, 4 figures

Combined macroscopic and microscopic approach to the fracture of metals. Technical progress report

International Nuclear Information System (INIS)

Asaro, R.J.; Gurland, J.; Needleman, A.; Rice, R.J.

1979-06-01

Progress is reported on microscopic fracture mechanisms, including studies of void and crack initiation in steels in the absence and presence of hydrogen, the effects of hydrogen on ductile fracture in medium and high carbon steels; elastic--plastic crack growth including the quasi-stable growth of cracks in ductile solids under increasing load and conditions of instability; and elevated temperature rupture including analysis of the stress field near a crack tip in an elastic-nonlinear viscous material under tensile load as well as the processes of diffusion, and cavitation of grain boundaries in plastically creeping materials

48 CFR 2052.211-70 - Preparation of technical reports.

Science.gov (United States)

2010-10-01

....211-70 Preparation of technical reports. As prescribed at 2011.104-70(a), the contracting officer... Reports (JAN 1993) All technical reports required by Section C and all Technical Progress Reports required... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Preparation of technical...

FY13 Annual Progress Report for SECA Core Technology Program

Energy Technology Data Exchange (ETDEWEB)

Stevenson, Jeffry W. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Koeppel, Brian J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2014-01-31

This progress report covers technical work performed during fiscal year 2013 at PNNL under Field Work Proposal (FWP) 40552. The report highlights and documents technical progress in tasks related to advanced cell and stack component materials development and computational design and simulation.

The challenge of the future. Technical progress and ecological perspectives

International Nuclear Information System (INIS)

Jischa, M.F.

1993-01-01

The book introduces readers into the interrelated global problems population dynamics, energy supply, imminent climate catastrophe, environmetal pollution, finite resources and the conflict between the North and South. It encourages probing more deeply into the technical challenges of the future. The author demonstrates why economic and technical issues will soon be outstripped by questions of the environmental, human and social compatibility of new technologies. (orig./UA) [de

Periodic progress report, 6 months

DEFF Research Database (Denmark)

Juhl, Thomas Winther; Nielsen, Jakob Skov

This is the first progress report of the BriteEuram project named "High Power Laser Cutting for Heavy Industry" ("Powercut"). The report contains a summary of the objectives of the first period, an overview of the technical progress, a comparison between the planed and the accomplished work...

Decomposing productivity growth allowing efficiency gains and price-induced technical progress

NARCIS (Netherlands)

Oude Lansink, A.G.J.M.; Silva, E.; Stefanou, S.

2000-01-01

Time- and firm-specific output technical efficiency measures are generated within a price-induced technological change framework. The firm-specific production frontier incorporates past prices as an argument encouraging innovation and a time trend to account for exogenous technical change. The

PFBC HGCU Test Facility. Technical progress report No. 24, Third quarter, CY 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-01

This is the twenty-fourth and final Technical Progress Report submitted to the Department of Energy (DOE) in connection with the cooperative agreement between the DOE and Ohio Power Company for the Tidd PFBC Hot Gas Clean Up Test Facility. This report covers the work completed during the Third Quarter of CY 1995. All activity this quarter was directed toward the completion of the program final report. A draft copy of the final report was forwarded to DOE during this quarter, and DOE submitted their comments on the report to AEPSC. DOE requested that Westinghouse write an appendix to the report covering the performance of the fail-safe regenerator devices during Tad operation, and Westinghouse subsequently prepared the appendix. Additional DOE comments were incorporated into the report, and it will be issued in camera-ready form by the end of October, 1995, which is the program end date. Appendix 1 presents the results of filter candle posttest examination by Westinghouse performed on selected filter candles following final shutdown of the system.

Method for the determination of technical specifications limiting temperature in EBR-II operation

International Nuclear Information System (INIS)

Chang, L.K.; Hill, D.J.; Ku, J.Y.

2004-01-01

The methodology and analysis procedure to qualify the Mark-V and Mark-VA fuels for the Experimental Breeder Reactor II are summarized in this paper. Fuel performance data and design safety criteria are essential for thermal-hydraulic analyses and safety evaluations. Normal and off-normal operation duty cycles and transient classifications are required for the safety assessment of the fuels. Design safety criteria for steady-state normal and transient off-normal operations were developed to ensure structural integrity of the fuel pin. The maximum allowable coolant outlet temperatures and powers of subassemblies for steady-state normal operation conditions were first determined in a row-by-row basis by a thermal-hydraulic and fuel damage analysis, in which a trial-and-error approach was used to predict the maximum subassembly coolant outlet temperatures and powers that satisfy the design safety criteria for steady-state normal operation conditions. The limiting steady-state temperature and power were then used as the initial subassembly thermal conditions for the off-normal transient analysis to assess the safety performance of the fuel pin for anticipated, unlikely and extremely unlikely events. If the design safety criteria for the off-normal events are not satisfied, then the initial steady-state subassembly temperatures and/or powers are reduced and an iterative procedure is employed until the design safety criteria for off-normal conditions are satisfied, and the initial subassembly outlet coolant temperature and power are the technical specification limits for reactor operation. (author)

Appropriability, Technological Opportunity, Market Demand, and Technical Change - Empirical Evidence from Switzerland

OpenAIRE

Harabi, Najib

1992-01-01

The purpose of this paper is to analyze both theoretically and empirically those factors which underlay the - empirically observable - inter-industry differences in technical progress. At the theoretical level economists agree more and more that technical progress can be explained at the industry level by the following three factors: (1) the technological opportunities, (2) the appropriability conditions, meaning the ability to capture and protect the results of technical innovations and (3) ...

GPHS-RTGs in support of the Cassini mission. Semi annual technical progress report, 2 October 1995--31 March 1996

International Nuclear Information System (INIS)

1996-01-01

The technical progress achieved during the period 2 October 1995 through 31 March 1996 on Contract No. DE-AC03-91SF18852, Radioisotope Generators and Ancillary Activities is described herein. This report is organized by the program task structure as follows: spacecraft integration and liaison; engineering support; safety; qualified unicouple fabrication; ETG fabrication, assembly, and test; ground support equipment (GSE); RTG shipping and launch support; designs, reviews, and mission applications; project management, quality assurance and reliability, contract changes, non-capital CAGO acquisition, and CAGO maintenance; contract acquired government-owned property (CAGO) acquisition; and program calendars

ISABELLE: a progress report

Energy Technology Data Exchange (ETDEWEB)

Hahn, H

1980-01-01

This paper discusses the ISABELLE project, which has the objective of constructing a high-energy proton colliding beam facility at Brookhaven National Laboratory. The major technical features of the intersecting storage accelerators with their projected performance are described. Application of over 1000 superconducting magnets in the two rings represents the salient characteristic of the machine. The status of the entire project, the technical progress made so far, and difficulties encountered are reviewed.

ISABELLE: a progress report

International Nuclear Information System (INIS)

Hahn, H.

1980-01-01

This paper discusses the ISABELLE project, which has the objective of constructing a high-energy proton colliding beam facility at Brookhaven National Laboratory. The major technical features of the intersecting storage accelerators with their projected performance are described. Application of over 1000 superconducting magnets in the two rings represents the salient characteristic of the machine. The status of the entire project, the technical progress made so far, and difficulties encountered are reviewed

The general technical regulation and the standardization

International Nuclear Information System (INIS)

Laverie, Michel; Houze, Christian; Lebouleux, Philippe

1980-01-01

Through a certain number of procedures, the thorough appreciation of the safety of a nuclear installation relies more on a specific appreciation taking into account the references as a whole, than on a technical regulation which claims to cover all the problems. Nevertheless, a French technical regulation structure regarding the safety domain must be built up progressively. The authors consider the principles of such a structure, and together they make the inventory of the works, finished, in progress or contemplated. The description of this specifically French approach emphazises the multiple and complementary forms given to statutory implements [fr

Annual technical progress report

International Nuclear Information System (INIS)

1980-01-01

During the present contract period Phaedrus has begun operation as a true tandem mirror. This was accomplished by achieving the rf sustained mode in which the plug densities were built up by a combination of central cell gas puffing and plug ICRH following stream gun turn off. It was demonstrated that the tandem mirror plasma could be sustained by plug ICRH for up to 1 msec following decay of the external plasma. In this mode plasma characteristics were no longer dominated by problems associated with a high conductivity stream gun plasma in the external region (as was the case in many previous experiments in Phaedrus). Among these problems were (1) line tying which significantly reduced instabilities in a way that would not apply to reactors and (2) low electron temperatures which had been held to approx. 20 eV

The calculated research of a fuel rod thermo technical safety at various laws of energy liberation and temperature changes

International Nuclear Information System (INIS)

Azarov, S.I.

1995-01-01

Different questions of the thermo technical safety and efficiency at various thermal loads in steady-state and transitional operating conditions are discussed. Resources up to heat exchange crisis at impulse, step and harmonical action when changing of coolant temperature and energy liberation in fuel are shown

Next Generation Nuclear Plant Project Technology Development Roadmaps: The Technical Path Forward for 750–800°C Reactor Outlet Temperature

Energy Technology Data Exchange (ETDEWEB)

John Collins

2009-08-01

This document presents the NGNP Critical PASSCs and defines their technical maturation path through Technology Development Roadmaps (TDRMs) and their associated Technology Readiness Levels (TRLs). As the critical PASSCs advance through increasing levels of technical maturity, project risk is reduced and the likelihood of within-budget and on-schedule completion is enhanced. The current supplier-generated TRLs and TDRMs for a 750–800°C reactor outlet temperature (ROT) specific to each supplier are collected in Appendix A.

Non-technical constraints to eradication: the Italian experience.

Science.gov (United States)

Moda, Giuliana

2006-02-25

Although technical constraints to eradication of bovine tuberculosis are well-recognised, non-technical constraints can also delay progress towards eradication, leading to inefficiency and increased programme costs. This paper seeks to analyse the main non-technical constraints that can interfere with the successful implementation of tuberculosis eradication plans, based on experiences from an area of high tuberculosis prevalence in Regione Piemonte, Italy. The main social and economic constraints faced in the past 20 years are reviewed, including a social reluctance to recognise the importance of seeking eradication as the goal of disease control, effective communication of technical issues, the training and the organization of veterinary services, the relationship between the regional authority and farmers and their representatives, and data management and epidemiological reporting. The paper analyses and discusses the solutions that were applied in Regione Piemonte and the benefits that were obtained. Tuberculosis eradication plans are one of the most difficult tasks of the Veterinary Animal Health Services, and non-technical constraints must be considered when progress towards eradication is less than expected. Organizational and managerial resources can help to overcome social or economic obstacles, provided the veterinary profession is willing to address technical, but also non-technical, constraints to eradication.

[Strategies and mechanisms of soil springtails in adapting lower temperature environment: research progress].

Science.gov (United States)

Liu, Jing; Wang, Yun-Biao; Wu, Dong-Hui

2012-12-01

Low temperature and drought are the main environmental factors threatening the animals living in arctic area and cold temperate regions. To adapt the severe environment, the animals should adopt appropriate strategies. As a group of arthopods with freeze-avoiding strategy, soil springtails have the similar ecological mechanisms and modes of cold resistance/tolerance as insects, manifesting in the cold acclimation and drought tolerance to decrease the damage of ice crystal formation. During cold acclimation, there are a rapid increase of glycerol, a rapid decrease of fucose and glucose, and the production of anti-freeze proteins (AFP) , and exists the inter-transformation of different kinds of lipids to improve the flow of cell membrane to protect the cell from low temperature injury. In addition, soil springtails have their own specific modes and mechanisms to tolerate low temperature stress, mainly the vertical migration under the protection of snow cover and the excretion of ice nucleator from haemolymph, illustrating that it's of significance to research the cryobiology of soil springtails. This paper summarized the modes and mechanisms of soil springtails in tolerating low temperature environment, reviewed the research progress on the eco-physiology of the springtails, discussed the existing problems of the researches on the low temperature tolerance of the springtails, and prospected the research directions of the springtails low temperature ecology under the background of global change.

TECHNICAL COORDINATION

CERN Multimedia

A. Ball and W. Zeuner

2011-01-01

In this report we will review the main achievements of the Technical Stop and the progress of several centrally-managed projects to support CMS operation and maintenance and prepare the way for upgrades. Overview of the extended Technical Stop  The principal objectives of the extended Technical Stop affecting the detector itself were the installation of the TOTEM T1 telescopes on both ends, the readjustment of the alignment link-disk in YE-2, the replacement of the light-guide sleeves for all PMs of both HFs, and some repairs on TOTEM T2 and CASTOR. The most significant tasks were, however, concentrated on the supporting infrastructure. A detailed line-by-line leak search was performed in the C6F14 cooling system of the Tracker, followed by the installation of variable-frequency drives on the pump motors of the SS1 and SS2 tracker cooling plants to reduce pressure transients during start-up. In the electrical system, larger harmonic filters were installed in ...

Effects of humic substances on the migration of radionuclides: complexation and transport of actinides. First technical progress report (work period 01.97 - 12.97)

International Nuclear Information System (INIS)

Buckau, G.

1998-08-01

The present report describes progress within the first year of the EC-project 'Effects of Humic Substances on the Migration of Radionuclides: Complexation and Transport of Actinides'. The project is conducted within the EC-Cluster 'Radionuclide Transport/Retardation Processes'. Contrary to formal requirements of the Commission, this report with a great deal of detail is established already after one year of project work. It is scheduled to be followed by a second technical progress report covering the second year of the project. In agreement with the contractual obligations a final report of similar technical detail will also be generated. The report contains an executive summary written by the coordinator (FZK/INE) with strong support from the other three task leaders (BGS, CEA-SGC and RMC-E). More detailed results are given by individual contributions of the project partners in 13 annexes. In the executive summary report the origin of results presented is given, also serving as guidance for finding more detailed results in the annexes. Not all results are discussed or referred to in the executive summary report and thus readers with a deeper interest also need to consult the annexes. (orig.)

Diagnostic development and support of MHD test facilities: Technical progress report for the period January, February, March 1985

International Nuclear Information System (INIS)

Shepard, W.S.; Cook, R.L.

1985-04-01

Mississippi State University is developing diagnostic instruments for MHD power train data acquisition and for support of MHD component development test facilities. Microprocessor-controlled optical instruments, initially developed for HRSR support, are being refined, and new systems to measure temperatures and gas-seed-slag stream characteristics are being developed. To further data acquisition and analysis capabilities, the diagnostic systems are being interfaced with MHD Energy Center computers. Additionally, technical support of the diagnostic needs of the national MHD research effort is being provided

Global observed long-term changes in temperature and precipitation extremes: A review of progress and limitations in IPCC assessments and beyond

Directory of Open Access Journals (Sweden)

Lisa V. Alexander

2016-03-01

Full Text Available The Intergovernmental Panel on Climate Change (IPCC first attempted a global assessment of long-term changes in temperature and precipitation extremes in its Third Assessment Report in 2001. While data quality and coverage were limited, the report still concluded that heavy precipitation events had increased and that there had been, very likely, a reduction in the frequency of extreme low temperatures and increases in the frequency of extreme high temperatures. That overall assessment had changed little by the time of the IPCC Special Report on Extremes (SREX in 2012 and the IPCC Fifth Assessment Report (AR5 in 2013, but firmer statements could be added and more regional detail was possible. Despite some substantial progress throughout the IPCC Assessments in terms of temperature and precipitation extremes analyses, there remain major gaps particularly regarding data quality and availability, our ability to monitor these events consistently and our ability to apply the complex statistical methods required. Therefore this article focuses on the substantial progress that has taken place in the last decade, in addition to reviewing the new progress since IPCC AR5 while also addressing the challenges that still lie ahead.

Feasibility study of electric motors constructed with high temperature superconducting materials

International Nuclear Information System (INIS)

Jordan, H.E.

1989-01-01

The potential application of high temperature superconducting (HTSC) materials to electric motors is discussed. The specific application area of motors in electric power generating stations has been selected and a feasible study has been initiated on the use of HTSC materials in the design of motors for this application. A progress report on this feasibility study is presented. Technical challenges in both the development of HTSC wire and the design of a motor to utilize this wire are discussed. Finally, the results of design calculations comparing a superconducting motor with one of conventional design are presented assuming that success can be achieved in overcoming the technical problems which must be resolved to produce a high performance HTSC wire

High Temperature Superconducting Underground Cable

International Nuclear Information System (INIS)

Farrell, Roger A.

2010-01-01

The purpose of this Project was to design, build, install and demonstrate the technical feasibility of an underground high temperature superconducting (HTS) power cable installed between two utility substations. In the first phase two HTS cables, 320 m and 30 m in length, were constructed using 1st generation BSCCO wire. The two 34.5 kV, 800 Arms, 48 MVA sections were connected together using a superconducting joint in an underground vault. In the second phase the 30 m BSCCO cable was replaced by one constructed with 2nd generation YBCO wire. 2nd generation wire is needed for commercialization because of inherent cost and performance benefits. Primary objectives of the Project were to build and operate an HTS cable system which demonstrates significant progress towards commercial progress and addresses real world utility concerns such as installation, maintenance, reliability and compatibility with the existing grid. Four key technical areas addressed were the HTS cable and terminations (where the cable connects to the grid), cryogenic refrigeration system, underground cable-to-cable joint (needed for replacement of cable sections) and cost-effective 2nd generation HTS wire. This was the worlds first installation and operation of an HTS cable underground, between two utility substations as well as the first to demonstrate a cable-to-cable joint, remote monitoring system and 2nd generation HTS.

Technical Progress Report

Energy Technology Data Exchange (ETDEWEB)

Paul D. Ronney

2004-08-26

An ignition source was constructed that is capable of producing a pulsed corona discharge for the purpose of igniting mixtures in a test chamber. The corona generator can also be used as the ignition source for one cylinder on a test engine. The first tests were performed in a cylindrical shaped chamber to study the characteristics of the corona and analyze various electrode geometries. Next a test chamber was constructed that closely represented the dimensions of the combustion chamber of the test engine at USC. Combustion tests were performed in this chamber and various electrode diameters and geometries were tested. Higher peak pressures and faster pressure rise times were realized consistently in all test chambers versus standard spark plug ignition. A test engine was purchased for the project that has two spark plug ports per cylinder to The data acquisition and control system hardware for the USC engine lab was updated with new equipment. New software was also developed to perform the engine control and data acquisition functions including cylinder pressure monitoring. A ceramic corona electrode has been designed that fits in the new test engine and is capable of withstanding the pressures and temperatures encountered inside the combustion chamber. The corona ignition system was tested on the engine and an increase in both peak pressure and IMEP were seen in the initial test. There are issues that must be addressed before on-engine testing can continue such as EMF interference from the corona generator and electrical insulation on portions of the piston and cylinder head to prevent arcing. The EMF issue can be solved with proper shielding and grounding and various ceramic coatings are being researched for electrical insulation.

Progress Report Oct to Dec 1975(2)

International Nuclear Information System (INIS)

1976-01-01

Progress report NO. 2 of Tehran Nuclear Research Centre outlines a brief description of the progress made in each section of the centre. A complete list of dissertations for Master's degrees studied at the Nuclear Research Centre and a list of new technical employee are given at the beginning of the report. Research activities in the third section include, isotope separation, laser research, radiation chemistry, reactor management, environmental research, neutron physics, reactor engineering, and nuclear medicine. The fourth section deals with education and training; technical support and health physics are discussed in sections five and six respectively

Progress report for '89

International Nuclear Information System (INIS)

Podest, M.

1990-08-01

The 1989 Progress Report presents the most important scientific and technical achievements of the Nuclear Research Institute's research work. Some specialized products prepared at or fabricated by the NRI are mentioned as well. (author). 24 figs., 8 tabs., 101 refs

C-Mod Collaboration Informal Technical Progress Report

International Nuclear Information System (INIS)

Kenneth W. Gentle

2007-01-01

The aims of the collaboration have not changed. A specific list of tasks was agreed upon during the Fall of 2006 in preparation for the 2007 C-Mod campaign by Earl Marmar, Head of the Alcator Project, Kenneth Gentle, Principal Investigator, and William Rowan, Collaboration Coordinator with the facilitation of Adam Rosenberg (DOE grant monitor for the collaboration). The activities follow the list of tasks and are discussed in this progress report

Research in elementary particle physics. Technical progress report, June 1, 1985-May 31, 1986

International Nuclear Information System (INIS)

Kirsch, L.E.; Schnitzer, H.J.; Bensinger, J.R.; Abbott, L.F.; Blocker, C.A.

1986-01-01

Progress is reported in both experimental and theoretical elementary particle research. Experimental activities include: construction of the Forward Electromagnetic Shower Counters for the Collider Detector at Fermilab (CDF); a test run in the CDF, involving observation of a small number of proton-antiproton collisions; design of a self-contained single wire proportional chamber with pressure and temperature sensing for monitoring the gain of gases used by various components of the CDF; data acquisition, and calibration. Also included are a search for a dibaryon of strangeness=-1; hyperon weak radiative decay. Theoretical research is reported in the areas of quantum field theory, string theory, elementary particle phenomenology, cosmology, field theory in curved spacetimes, and cosmology. 34 refs

Progress report 1979

International Nuclear Information System (INIS)

1980-12-01

This progress report deals with technical and research work done at the AAEC Research Establishment in the twelve month period ending September 30, 1979. Work done in the following research divisions is reported: Applied Maths and Computing, Chemical Technology, Engineering Research, Environmental Science, Instrumentation and Control, Isotope, Materials and Physics

Nuclear Energy Research Initiative (NERI) Program. Technical progress report

International Nuclear Information System (INIS)

Engelhardt, G.R.; MacDonald, D.D.

2000-01-01

During the past quartile the authors have explored the thermodynamics of various metal hydroxide and oxyhydroxide dehydration reactions of iron, nickel, and chromium with the objective of estimating the critical temperature, T(sub cr). This is the temperature at which the oxide is in equilibrium with the oxyhydroxide or hydroxide and water vapor under the expected repository conditions of temperature and pressure. Because localized corrosion requires the presence of an ionically conducting phase on the surface (to support oxygen reduction) T(sub cr) is also the temperature below which ''wet'' corrosion first becomes possible. Past analyses have assumed that wet corrosion requires the presence of a layer of bulk water on the surface and hence that corrosion is not possible at temperatures above the boiling temperature of bulk water under the prevailing atmospheric pressure. Furthermore, significant elevation of the boiling temperature may occur if the aqueous phase becomes concentrated in salts. Because of the hydration of hygroscopic corrosion products, which may occur at significantly higher temperatures than the boiling temperature of water, and because of boiling temperature elevation effects, the past assumption needs to be reevaluated. This is the primary goal of this work

Progress report [of] Technical Physics Division

International Nuclear Information System (INIS)

Vijendran, P.; Deshpande, R.Y.

1975-01-01

Activities of the Technical Physics Division of the Bhabha Atomic Research Centre, Bombay, over the last few years are reported. This division is engaged in developing various technologies supporting the development of nuclear technology. The various fields in which development is actively being carried out are : (i) vacuum technology, (ii) mass spectrometry, (iii) crystal technology, (iv) cryogenics, and (v) magnet technology. For surface studies, the field emission microscope and the Auger electron spectrometer and other types of spectrometers have been devised and perfected. Electromagnets of requisite strength to be used in MHD programme and NMR instruments are being fabricated. Various crystals such as NaI(Tl), Ge, Fluorides, etc. required as windows and prisms in X and gamma-ray spectroscopy, have been grown. In the cryogenics field, expansion engines required for air liquefaction plants, vacuum insulated dewars, helium gas thermometers etc. have been constructed. In addition to the above, the Division provides consultancy and training to personnel from various institutions and laboratories. Equipment and systems perfected are transferred to commercial organizations for regular production. (A.K.)

Effects of temperature on disease progression and swimming stamina in Ichthyophonus-infected rainbow trout, Oncorhynchus mykiss (Walbaum).

Science.gov (United States)

Kocan, R; Hershberger, P; Sanders, G; Winton, J

2009-10-01

Rainbow trout, Oncorhynchus mykiss, were infected with Ichthyophonus sp. and held at 10 degrees C, 15 degrees C and 20 degrees C for 28 days to monitor mortality and disease progression. Infected fish demonstrated more rapid onset of disease, higher parasite load, more severe host tissue reaction and reduced mean-day-to-death at higher temperature. In a second experiment, Ichthyophonus-infected fish were reared at 15 degrees C for 16 weeks then subjected to forced swimming at 10 degrees C, 15 degrees C and 20 degrees C. Stamina improved significantly with increased temperature in uninfected fish; however, this was not observed for infected fish. The difference in performance between infected and uninfected fish became significant at 15 degrees C (P = 0.02) and highly significant at 20 degrees C (P = 0.005). These results have implications for changes in the ecology of fish diseases in the face of global warming and demonstrate the effects of higher temperature on the progression and severity of ichthyophoniasis as well as on swimming stamina, a critical fitness trait of salmonids. This study helps explain field observations showing the recent emergence of clinical ichthyophoniasis in Yukon River Chinook salmon later in their spawning migration when water temperatures were high, as well as the apparent failure of a substantial percentage of infected fish to successfully reach their natal spawning areas.

Effects of temperature on disease progression and swimming stamina in Ichthyophonus-infected rainbow trout, Oncorhynchus mykiss (Walbaum)

Science.gov (United States)

Kocan, R.; Hershberger, P.; Sanders, G.; Winton, J.

2009-01-01

Rainbow trout, Oncorhynchus mykiss, were infected with Ichthyophonus sp. and held at 10 ??C, 15 ??C and 20 ??C for 28 days to monitor mortality and disease progression. Infected fish demonstrated more rapid onset of disease, higher parasite load, more severe host tissue reaction and reduced mean-day-to-death at higher temperature. In a second experiment, Ichthyophonus-infected fish were reared at 15 ??C for 16 weeks then subjected to forced swimming at 10 ??C, 15 ??C and 20 ??C. Stamina improved significantly with increased temperature in uninfected fish; however, this was not observed for infected fish. The difference in performance between infected and uninfected fish became significant at 15 ??C (P = 0.02) and highly significant at 20 ??C (P = 0.005). These results have implications for changes in the ecology of fish diseases in the face of global warming and demonstrate the effects of higher temperature on the progression and severity of ichthyophoniasis as well as on swimming stamina, a critical fitness trait of salmonids. This study helps explain field observations showing the recent emergence of clinical ichthyophoniasis in Yukon River Chinook salmon later in their spawning migration when water temperatures were high, as well as the apparent failure of a substantial percentage of infected fish to successfully reach their natal spawning areas. ?? 2009 Blackwell Publishing Ltd.

Technical progress report for UTSI/CFFF MHD program completion and related activity

International Nuclear Information System (INIS)

Chapman, James N.; Muehlhauser, Joel W.

1998-01-01

Routine preventive maintenance of the DOE Coal Fired Flow Facility (CFFF) is being performed. Modernization programs, funded under subcontract from Foster Wheeler Development Corporation by the DOE HIPPS Program, have been completed on the coal processing system, the data acquisition and control system and the control room. Late in the quarter, all work was stopped on maintenance of the CFFF at DOE instruction. Environmental restoration actions continued with monitoring of groundwater wells and holding pond effluent. Progress is reported on the approved groundwater remediation plan. Actions are underway to dispose of spent seed/ash mixtures and excess coal remaining from the MHD POC program. The status of five (5) High Temperature Superconductor (HTS) projects is reported. A summary is included of the results attained with sol-gel experiments with buffer layers and YBCO. The status of the cost/performance study of electron beam and PLD deposition is pre-sented. A summary of work performed in diagnostics for real time control of HTS processes is presented

TECHNICAL PROGRESS REPORT FOR UTSI/CFFF MHD PROGRAM COMPLETION AND RELATED ACTIVITIES

Energy Technology Data Exchange (ETDEWEB)

DR. JAMES N. CHAPMAN; DR. JOEL W. MUEHLHAUSER

1998-10-23

Routine preventive maintenance of the DOE Coal Fired Flow Facility (CFFF) is being performed. Modernization programs, funded under subcontract from Foster Wheeler Development Corporation by the DOE HIPPS Program, have been completed on the coal processing system, the data acquisition and control system and the control room. Late in the quarter, all work was stopped on maintenance of the CFFF at DOE instruction. Environmental restoration actions continued with monitoring of groundwater wells and holding pond effluent. Progress is reported on the approved groundwater remediation plan. Actions are underway to dispose of spent seed/ash mixtures and excess coal remaining from the MHD POC program. The status of five (5) High Temperature Superconductor (HTS) projects is reported. A summary is included of the results attained with sol-gel experiments with buffer layers and YBCO. The status of the cost/performance study of electron beam and PLD deposition is pre-sented. A summary of work performed in diagnostics for real time control of HTS processes is presented.

The development of an e-learning software, ''Technical ethics''

International Nuclear Information System (INIS)

Matsue, Kazuki; Madarame, Haruki; Okamoto, Koji

2004-01-01

For the engineers and researchers, it is coming to the time when they are asked not only technical progress but also their ethics view. In this study, I aim to develop of the education software ''Technical Ethics'', which cultivates ethics view of the engineers. (author)

High temperature gas cooled reactor technology development. Proceedings of a technical committee meeting

International Nuclear Information System (INIS)

1997-12-01

The successful introduction of an advanced nuclear power plant programme depends on many key elements. It must be economically competitive with alternative sources of energy, its technical development must assure operational dependability, the support of society requires that it be safe and environmentally acceptable, and it must meet the regulatory standards developed for its use and application. These factors interrelate with each other, and the ability to satisfy the established goals and criteria of all of these requirements is mandatory if a country or a specific industry is to proceed with a new, advanced nuclear power system. It was with the focus on commercializing the high temperature gas cooled reactor (HTGR) that the IAEA's International Working Group on Gas Cooled Reactors recommended this Technical Committee Meeting (TCM) on HTGR Technology Development. Over the past few years, many Member States have instituted a re-examination of their nuclear power policies and programmes. It has become evident that the only realistic way to introduce an advanced nuclear power programme in today's world is through international co-operation between countries. The sharing of expertise and technical facilities for the common development of the HTGR is the goal of the Member States comprising the IAEA's International Working Group on Gas Cooled Reactors. This meeting brought together key representatives and experts on the HTGR from the national organizations and industries of ten countries and the European Commission. The state electric utility of South Africa, Eskom, hosted this TCM in Johannesburg, from 13 to 15 November 1996. This TCM provided the opportunity to review the status of HTGR design and development activities, and especially to identify international co-operation which could be utilized to bring about the commercialization of the HTGR

Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2008

Energy Technology Data Exchange (ETDEWEB)

Korsholm, S.B.; Michelsen, P.K.; Rasmussen, J.J.; Westergaard, C.M. (eds.)

2009-04-15

The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. New activities in technology related to development of high temperature superconductors have been initiated in 2008. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2008. (Author)

Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2010

Energy Technology Data Exchange (ETDEWEB)

Korsholm, S.B.; Michelsen, P.K.; Rasmussen, J.J.; Westergaard, C.M. (eds.)

2011-04-15

The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology there are activities related to development of high temperature superconductors. Other activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2010. (Author)

Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2008

International Nuclear Information System (INIS)

Korsholm, S.B.; Michelsen, P.K.; Rasmussen, J.J.; Westergaard, C.M.

2009-04-01

The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. New activities in technology related to development of high temperature superconductors have been initiated in 2008. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2008. (Author)

Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2009

International Nuclear Information System (INIS)

Korsholm, S.B.; Michelsen, P.K.; Rasmussen, J.J.; Westergaard, C.M.

2010-04-01

The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology there are activities related to development of high temperature superconductors. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2009. (Author)

Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2009

Energy Technology Data Exchange (ETDEWEB)

Korsholm, S B; Michelsen, P K; Rasmussen, J J; Westergaard, C M [eds.

2010-04-15

The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology there are activities related to development of high temperature superconductors. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2009. (Author)

Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2010

International Nuclear Information System (INIS)

Korsholm, S.B.; Michelsen, P.K.; Rasmussen, J.J.; Westergaard, C.M.

2011-04-01

The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology there are activities related to development of high temperature superconductors. Other activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2010. (Author)

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

John Ross

2003-04-30

The Final Technical Report summarizes research accomplishments and Publications in the period of 5/1/99 to 4/30/03 done on the grant. Extensive progress was made in the period covered by this report in the areas of chemical kinetics of non-linear systems; spatial structures, reaction - diffusion systems, and thermodynamic and stochastic theory of electrochemical and general systems.

Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. An extra issue: background of the geological disposal

International Nuclear Information System (INIS)

1999-11-01

Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the geological disposal concept for high-level radioactive wastes (HLW) in Japan. The present document, an extra issue of the progress report, was prepared for the expected readers of the report to have background information on the geological disposal. Thus it gives information about (1) generation of high-level radioactive wastes, (2) history of plans proposed for HLW disposal in Japan, and (3) procedure until the geological disposal plan is finally adopted and basic future schedules. It further discusses on such problems in HLW treatment and disposal, as for example a problem of reliable safety for a very long period. (Ohno, S.)

GT-MHR COMMERCIALZATION STUDY. TECHNICAL PROGRESS AND COST MANAGEMENT REPORT FOR THE PERIOD JUNE 1 THROUGH JUNE 30, 2003

International Nuclear Information System (INIS)

SHENOY, A.S.

2003-01-01

A271 GT-MHR COMMERCIALZATION STUDY TECHNICAL PROGRESS AND COST MANAGEMENT REPORT FOR THE PERIOD JUNE 1 THROUGH JUNE 30, 2003. Petten was provided with irradiation dimensional change data for both fuel compacts and H-451 graphite for design of the graphite sleeves that hold the fuel compacts to be irradiated in HFR-EU2. The Fuel Sample Product Specification for the Fuel Performance Irradiation Test Capsule MHR-2 was completed and approved. A Work Breakdown Structure was prepared for the development and qualification of advanced coated-particle fuels capable of meeting anticipated fuel performance requirements and work was initiated on preparation of schedules and a cost estimates for the test matrices

Electrical and Electronics Technical Team Roadmap

Energy Technology Data Exchange (ETDEWEB)

None

2013-06-01

The Electrical and Electronics Technical Team’s (EETT's) mission is to enable cost-effective, smaller, lighter, and efficient power electronics and electric motors for electric traction drive systems (ETDSs) while maintaining performance of internal combustion engine (ICE)-based vehicles. The EETT also identifies technology gaps, establishes R&D targets, develops a roadmap to achieve technical targets and goals, and evaluates the R&D progress toward meeting the established R&D targets and goals.

ATR Technical Specification Upgrade Program

International Nuclear Information System (INIS)

McCracken, R.T.; Durney, J.L.; Freund, G.A.

1990-01-01

The Advanced Test Reactor (ATR) is a 250 MW, uranium-aluminum fueled test reactor which began full power operation in 1969. The initial operation was controlled by an Operating Limits document based on the original Safety Analysis Report. Additional safety bases were later developed to support Technical Specifications which were approved and implemented in 1977. The Technical Specifications which were initially developed with content and format specified in ANSI/ANS--15.1, ''The Development of Technical Specifications for Research Reactors.'' The safety basis documentation and the Technical Specifications have been updated as required to maintain them current with the ATR facility configuration. All revisions have been made with a content, format and style consistent with the original. A major, two-phase program to upgrade the content, format and style is in progress. This paper describes the first phase of this program

Technical progress report, 1 April-30 June 1981

Energy Technology Data Exchange (ETDEWEB)

None

1981-01-01

This report describes the technical accomplishments during the quarter ending June 1981, on the commercial nuclear waste management programs under the direction of the Office of Nuclear Waste Isolation (ONWI). The ONWI program is organized into 8 tasks entitled: systems, waste package, site, repository, regulatory and institutional, test facilities and excavations, land acquisition, and program management. Principal investigators in each of these areas have submitted summaries of quarterly highlights for inclusion in this report. Separate abstracts have been prepared for 5 of these tasks for inclusion in the Energy Data Base. (DMC)

Technical progress of nuclear energy: economic and environmental prospects

International Nuclear Information System (INIS)

Naudet, G.

1994-01-01

This document deals with three different aspects of the nuclear energy: first the operating and economic performances of nuclear power plants in the world, the French nuclear competitiveness. Then, the technical and economic perspectives about reactors and fuels cycle and the advantages towards atmospheric pollution are discussed to favour a new worldwide nuclear development. (TEC). 8 refs., 4 figs., 6 tabs

High temperature fracture and fatigue of ceramics. Annual technical progress report No. 6, August 15, 1994--August 14, 1995

Energy Technology Data Exchange (ETDEWEB)

Cox, B.

1996-04-01

This report covers work done in the first year of our new contract {open_quotes}High Temperature Fracture and Fatigue of Ceramics,{close_quotes} which commenced in August, 1995 as a follow-on from our prior contract {open_quotes}Mechanisms of Mechanical Fatigue in Ceramics.{close_quotes} Our activities have consisted mainly of studies of the failure of fibrous ceramic matrix composites (CMCs) at high temperature; with a little fundamental work on the role of stress redistribution in the statistics of fracture and cracking in the presence of viscous fluids.

Self vs expert assessment of technical and non-technical skills in high fidelity simulation.

Science.gov (United States)

Arora, Sonal; Miskovic, Danilo; Hull, Louise; Moorthy, Krishna; Aggarwal, Rajesh; Johannsson, Helgi; Gautama, Sanjay; Kneebone, Roger; Sevdalis, Nick

2011-10-01

Accurate assessment is imperative for learning, feedback and progression. The aim of this study was to examine whether surgeons can accurately self-assess their technical and nontechnical skills compared with expert faculty members' assessments. Twenty-five surgeons performed a laparoscopic cholecystectomy (LC) in a simulated operating room. Technical and nontechnical performance was assessed by participants and faculty members using the validated Objective Structured Assessment of Technical Skills (OSATS) and the Non-Technical Skills for Surgeons scale (NOTSS). Assessment of technical performance correlated between self and faculty members' ratings for experienced (median score, 30.0 vs 31.0; ρ = .831; P = .001) and inexperienced (median score, 22.0 vs 28.0; ρ = .761; P = .003) surgeons. Assessment of nontechnical skills between self and faculty members did not correlate for experienced surgeons (median score, 8.0 vs 10.5; ρ = -.375; P = .229) or their more inexperienced counterparts (median score, 9.0 vs 7.0; ρ = -.018; P = .953). Surgeons can accurately self-assess their technical skills in virtual reality LC. Conversely, formal assessment with faculty members' input is required for nontechnical skills, for which surgeons lack insight into their behaviours. Copyright © 2011 Elsevier Inc. All rights reserved.

Nuclear theory research. Technical progress report

International Nuclear Information System (INIS)

1982-01-01

Progress is briefly described on the following studies: (1) Dirac phenomenology for deuteron elastic scattering, (2) Dirac wave functions in nuclear distorted wave calculations, (3) impulse approximation for p→p → dπ + reaction above the 3-3 resonance, (4) coherent π production, (5) nuclear potentials from Dirac bound state wavefunctions, (6) nonlocality effects in nuclear reactions, (7) unhappiness factors in DWBA description of (t,p) and (p,t) reactions, (8) absolute normalization of three-nucleon transfer reactions, (9) formulation of a finite-range CCBA computer program, (10) crossing symmetric solutions of the low equations, (11) pion scattering from quark bags, (12) study of the p 11 channel in the delta model, (13) isovector corrections in pion-nucleus scattering, (14) pionic excitation of nuclear giant resonances, and (15) isospin dependence of the second-order pion-nucleus optical potential

Progress in z-pinch driven dynamic-hohlraums for high-temperature radiation-flow and ICF experiments at Sandia National Laboratories

International Nuclear Information System (INIS)

Sanford, T W L; Nash, T J; Olson, R E; Bliss, D E; Lemke, R W; Olson, C L; Ruiz, C L; Mock, R C; Bailey, J E; Chandler, G A; Cuneo, M E; Leeper, R J; Matzen, M K; Mehlhorn, T A; Slutz, S A; Stygar, W A; Peterson, D L; Chrien, R E; Watt, R G; Roderick, N F; Cooper, G W; Apruzese, J P; Sarkisov, G S; Chittenden, J P; Haines, M G

2004-01-01

Progress in understanding the physics of dynamic-hohlraums is reviewed for a system capable of generating 13 TW of axial radiation for high temperature (>200 eV) radiation-flow experiments and ICF capsule implosions

Basalt Waste Isolation Project Technical Program Evaluation Process: a criteria-based method

International Nuclear Information System (INIS)

Babad, H.; Evans, G.C.; Wolfe, B.A.

1982-01-01

The need to objectively evaluate the progress being made by the Basalt Waste Isolation Project (BWIP) toward establishing the feasibility of siting a nuclear waste repository in basalt (NWRB) mandates a process for evaluating the technical work of the project. To assist BWIP management in the evaluation process, the Systems Department staff has developed a BWIP Technical Program Evaluation Process (TPEP). The basic process relates progress on project technical work to the SWIP Functional and System Performance Criteria as defined in National Waste Terminal Storage (MWTS) Criteria Documents. The benefits of the TPEP to BWIP and future plans for TPEP are discussed. During fiscal year (FY) 1982, TPEP wll be further formalized and further applied to the review of BWIP technical activities

Technical Progress Report on Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration

Energy Technology Data Exchange (ETDEWEB)

Bill Stanley; Patrick Gonzalez; Sandra Brown; Jenny Henman; Ben Poulter; Sarah Woodhouse Murdock; Neil Sampson; Tim Pearson; Sarah Walker; Zoe Kant; Miguel Calmon; Gilberto Tiepolo

2006-06-30

The Nature Conservancy is participating in a Cooperative Agreement with the Department of Energy (DOE) National Energy Technology Laboratory (NETL) to explore the compatibility of carbon sequestration in terrestrial ecosystems and the conservation of biodiversity. The title of the research project is ''Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration''. The objectives of the project are to: (1) improve carbon offset estimates produced in both the planning and implementation phases of projects; (2) build valid and standardized approaches to estimate project carbon benefits at a reasonable cost; and (3) lay the groundwork for implementing cost-effective projects, providing new testing ground for biodiversity protection and restoration projects that store additional atmospheric carbon. This Technical Progress Report discusses preliminary results of the six specific tasks that The Nature Conservancy is undertaking to answer research needs while facilitating the development of real projects with measurable greenhouse gas reductions. The research described in this report occurred between April 1st and July 30th 2006. The specific tasks discussed include: Task 1: carbon inventory advancements; Task 2: emerging technologies for remote sensing of terrestrial carbon; Task 3: baseline method development; Task 4: third-party technical advisory panel meetings; Task 5: new project feasibility studies; and Task 6: development of new project software screening tool. Work is being carried out in Brazil, Belize, Chile, Peru and the USA.

Short periods of high temperature during meiosis prevent normal meiotic progression and reduce grain number in hexaploid wheat (Triticum aestivum L.).

Science.gov (United States)

Draeger, Tracie; Moore, Graham

2017-09-01

Exposure of wheat to high temperatures during male meiosis prevents normal meiotic progression and reduces grain number. We define a temperature-sensitive period and link heat tolerance to chromosome 5D. This study assesses the effects of heat on meiotic progression and grain number in hexaploid wheat (Triticum aestivum L. var. Chinese Spring), defines a heat-sensitive stage and evaluates the role of chromosome 5D in heat tolerance. Plants were exposed to high temperatures (30 or 35 °C) in a controlled environment room for 20-h periods during meiosis and the premeiotic interphase just prior to meiosis. Examination of pollen mother cells (PMCs) from immature anthers immediately before and after heat treatment enabled precise identification of the developmental phases being exposed to heat. A temperature-sensitive period was defined, lasting from premeiotic interphase to late leptotene, during which heat can prevent PMCs from progressing through meiosis. PMCs exposed to 35 °C were less likely to progress than those exposed to 30 °C. Grain number per spike was reduced at 30 °C, and reduced even further at 35 °C. Chinese Spring nullisomic 5D-tetrasomic 5B (N5DT5B) plants, which lack chromosome 5D, were more susceptible to heat during premeiosis-leptotene than Chinese Spring plants with the normal (euploid) chromosome complement. The proportion of plants with PMCs progressing through meiosis after heat treatment was lower for N5DT5B plants than for euploids, but the difference was not significant. However, following exposure to 30 °C, in euploid plants grain number was reduced (though not significantly), whereas in N5DT5B plants the reduction was highly significant. After exposure to 35 °C, the reduction in grain number was highly significant for both genotypes. Implications of these findings for the breeding of thermotolerant wheat are discussed.

The higher temperature in the areola supports the natural progression of the birth to breastfeeding continuum.

Directory of Open Access Journals (Sweden)

Vincenzo Zanardo

Full Text Available Numerous functional features that promote the natural progression of the birth to breastfeeding continuum are concentrated in the human female's areolar region. The aim of this study was to look more closely into the thermal characteristics of areola, which are said to regulate the local evaporation rate of odors and chemical signals that are uniquely important for the neonate's 'breast crawl'. A dermatological study of the areolae and corresponding intern breast quadrants was undertaken on the mothers of 70 consecutive, healthy, full-term breastfed infants. The study took place just after the births at the Policlinico Abano Terme, in Italy from January to February 2014. Temperature, pH and elasticity were assessed one day postpartum using the Soft Plus 5.5 (Callegari S.P.A., Parma, Italy. The mean areolar temperature was found to be significantly higher than the corresponding breast quadrant (34.60 ±1.40°C vs. 34.04 ±2.00°C, p<0.001 and the pH was also significantly higher (4.60±0.59 vs. 4.17±0.59, p<0.001. In contrast, the elasticity of the areolar was significantly lower (23.52±7.83 vs. 29.02±8.44%, p<0.003. Our findings show, for the first time, that the areolar region has a higher temperature than the surrounding breast skin, together with higher pH values and lower elasticity. We believe that the higher temperature of the areolar region may act as a thermal signal to guide the infant directly to the nipple and to the natural progression of the birth to breastfeeding continuum.

Fuel Rod Melt Progression Simulation Using Low-Temperature Melting Metal Alloy

International Nuclear Information System (INIS)

Seung Dong Lee; Suh, Kune Y.; GoonCherl Park; Un Chul Lee

2002-01-01

The TMI-2 accident and various severe fuel damage experiments have shown that core damage is likely to proceed through various states before the core slumps into the lower head. Numerous experiments were conducted to address when and how the core can lose its original geometry, what geometries are formed, and in what processes the core materials are transported to the lower plenum of the reactor pressure vessel. Core degradation progresses along the line of clad ballooning, clad oxidation, material interaction, metallic blockage, molten pool formation, melt progression, and relocation to the lower head. Relocation into the lower plenum may occur from the lateral periphery or from the bottom of the core depending upon the thermal and physical states of the pool. Determining the quantities and rate of molten material transfer to the lower head is important since significant amounts of molten material relocated to the lower head can threaten the vessel integrity by steam explosion and thermal and mechanical attack of the melt. In this paper the focus is placed on the melt flow regime on a cylindrical fuel rod utilizing the LAMDA (Lumped Analysis of Melting in Degrading Assemblies) facility at the Seoul National University. The downward relocation of the molten material is a combination of the external film flow and the internal pipe flow. The heater rods are 0.8 m long and are coated by a low-temperature melting metal alloy. The electrical internal heating method is employed during the test. External heating is adopted to simulate the exothermic Zircaloy-steam reaction. Tests are conducted in several quasi-steady-state conditions. Given the variable boundary conditions including the heat flux and the water level, observation is made for the melting location, progression, and the mass of molten material. Finally, the core melt progression model is developed from the visual inspection and quantitative analysis of the experimental data. As the core material relocates

Geothermal space/water heating for Mammoth Lakes Village, California. Quarterly technical progress report, 13 December 1976-12 March 1977

Energy Technology Data Exchange (ETDEWEB)

Sims, A.V.; Racine, W.C.

1977-01-01

During the second three months of this feasibility study to determine the technical, economic and environmental feasibility of heating Mammoth Lakes Village, California using geothermal energy, the following work was accomplished. A saturation survey of the number and types of space and water heaters currently in use in the Village was completed. Electric energy and ambient temperature metering equipment was installed. Peak heating demand for Mammoth Lakes was estimated for the years 1985, 1990 and 2000. Buildings were selected which are considered typical of Mammoth Lakes in terms of their heating systems to be used in estimating the cost of installing hydronic heating systems in Mammoth. Block diagrams and an order of magnitude cost comparison were prepared for high-temperature and low-temperature geothermal district heating systems. Models depicting a geothermal district heating system and a geothermal-electric power plant were designed, built and delivered to ERDA in Washington. Local input to the feasibility study was obtained from representatives of the State of California Departments of Transportation and Fish and Game, US Forest Service, and Mono County Planning Department.

Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. Part 3. Safety assessment for geological disposal systems

International Nuclear Information System (INIS)

1999-11-01

Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the geological disposal concept for high-level radioactive wastes (HLW) in Japan. The present document, the part 3 of the progress report, concerns safety assessment for geological disposal systems definitely introduced in part 1 and 2 of this series and consists of 9 chapters. Chapter I concerns the methodology for safety assessment while Chapter II deals with diversity and uncertainty about the scenario, the adequate model and the required data of the systems above. Chapter III summarizes the components of the geological disposal system. Chapter IV refers to the relationship between radioactive wastes and human life through groundwater, i.e. nuclide migration. In Chapter V is made a reference case which characterizes the geological environmental data using artificial barrier specifications. (Ohno. S.)

Defining a Progress Metric for CERT RMM Improvement

Science.gov (United States)

2017-09-14

REV-03.18.2016.0 Defining a Progress Metric for CERT-RMM Improvement Gregory Crabb Nader Mehravari David Tobar September 2017 TECHNICAL ...fendable resource allocation decisions. Technical metrics measure aspects of controls implemented through technology (systems, soft- ware, hardware...implementation metric would be the percentage of users who have received anti-phishing training . • Effectiveness/efficiency metrics measure whether

Introducing errors in progress ratios determined from experience curves

NARCIS (Netherlands)

van Sark, W.G.J.H.M.

2008-01-01

Progress ratios (PRs) derived from historical data in experience curves are used for forecasting development of many technologies as a means to model endogenous technical change in for instance climate–economy models. These forecasts are highly sensitive to uncertainties in the progress ratio. As a

Recent progress in the melt-process technique of high-temperature superconductors

CERN Document Server

Ikuta, H; Mizutani, U

1999-01-01

Recently, the performance of high-temperature super conductors prepared by the melt-process technique has been greatly improved. This progress was accomplished by the addition of Ag into the starting materials of the Sm-Ba-CuO $9 system, which prevents the formation of severe macro-sized cracks in the finished samples. The magnetic flux density trapped by this material has now reached 9 T at 25 K, which is comparable to the magnetic flux density produced by $9 ordinary superconducting magnets. The amount of magnetic flux density that can be trapped by the sample is limited by the mechanical strength rather than superconducting properties of the material. The increase in the mechanical $9 strength of the material is important both for further improvement of the material properties and for ensuring reliability of the material in practical applications. (20 refs).

The Basalt Waste Isolation Project technical program evaluation process: A criteria-based method

International Nuclear Information System (INIS)

Babad, H.; Evans, C.; Wolfe, B.A.

1982-01-01

The need to objectively evaluate the progress being made by the Basalt Waste Isolation Project (BWIP) toward establishing the feasibility of siting a nuclear waste repository in basalt (NWRB) mandates a process for evaluating the technical work of the project. To assist BWIP management in the evaluation process, the Systems Department staff has developed a BWIP Technical Program Evaluation Process (TPEP). The basic process relates progress on project technical work to the BWIP Functional and System Performance Criteria as defined in National Waste Terminal Storage (NWTS) Criteria Documents. The benefits of the TPEP to BWIP and future plans for TPEP are discussed. During fiscal year (FY) 1982, TPEP will be further formalized and further applied to the review of BWIP technical activities

Feed-in tariffs versus quotas: how to promote renewable s and stimulate technical progress for cost decrease?

International Nuclear Information System (INIS)

Menanteau, Ph.; Finon, D.; Lamy, M.L.

2002-01-01

Incentive schemes for the development of renewable energy sources may focus on quantities (defining national targets and setting up bidding systems, or quota systems providing for green certificate trading), or they may focus on prices (feed-in tariffs). Whatever the system chosen, the role of the public authorities is quite specific: to stimulate technical progress and speed up the technological learning processes so that ultimately renewable energy technologies will be able to compete with conventional technologies, once the environmental costs have been internalized. A comparison of instruments must thus take into account the characteristics of the innovation process and adoption conditions (uncertainties regarding cost curves, learning effects) which means also looking at dynamic efficiency criteria. The paper concludes that a system of feed-in tariffs is more efficient than a bidding system, but highlights the theoretical interest of green certificate trading which must be confirmed through practice, given the influence of market structures and rules on the performance of this type of approach. (author)

Development of Nano-crystalline Doped-Ceramic Enabled Fiber Sensors for High Temperature In-Situ Monitoring of Fossil Fuel Gases

Energy Technology Data Exchange (ETDEWEB)

Xiao, Hai [Missouri Univ. of Science and Technology, Rolla, MO (United States); Dong, Junhang [Univ. of Cincinnati, OH (United States); Lin, Jerry [Arizona State Univ., Tempe, AZ (United States); Romero, Van [New Mexico Institute of Mining and Technology, Socorro, NM (United States)

2012-03-01

This is a final technical report for the first project year from July 1, 2005 to Jan 31, 2012 for DoE/NETL funded project DE-FC26-05NT42439: Development of Nanocrystalline Doped-Ceramic Enabled Fiber Sensors for High Temperature In-Situ Monitoring of Fossil Fuel Gases. This report summarizes the technical progresses and achievements towards the development of novel nanocrystalline doped ceramic material-enabled optical fiber sensors for in situ and real time monitoring the gas composition of flue or hot gas streams involved in fossil-fuel based power generation and hydrogen production.

Progress report for 1978-79, Technical Physics Division

International Nuclear Information System (INIS)

Gopalaraman, C.P.; Deshpande, R.Y.

1980-01-01

The research and development activities of the Technical Physics Division (TPD) of the Bhabha Atomic Research Centre, Bombay, during the calendar years 1978 and 1979 are reported. The TPD's major areas of work are electronics instrumentation, crystal technology, mass spectrometers, cryogenic equipment and vacuum equipment. Some of the major achievements are: (1) fabrication of various electronic instruments and components for the pulsed nuclear magnetic resonance spectrometers, (2) growth of large size NaI(Tl) and Ge crystals, (3) growth of CsI, KDP and arsenic selenide crystals, (4) fabrication of quadrupole mass filters and (5) fabrication of mass spectrometers for gas analysis and D/H analysis in water samples. (M.G.B.)

Sources of technical assistance

International Nuclear Information System (INIS)

Laue, H.J.

1977-01-01

This paper shows examples of technical assistance programmes within bilateral cooperation agreements between the Federal Republic of Germany and a number of developing countries of very different characteristics and summarizes the possibilities of technical assistance granted by international organizations, such as IAEA, UNDP, etc. A basic requirement for a successful transfer of technology is a high knowledge level of the indigenous scientists and engineers. Therefore, programmes for training and education and for information exchange are presented. Based on these, the means and methods of planning, performance and quality assurance are explained by practical examples and are related to the progress achieved in the use of nuclear energy and in establishing a national industry in the developing countries. (orig.) [de

Geothermal progress monitor. Progress report No. 3, March-April 1980

Energy Technology Data Exchange (ETDEWEB)

1980-01-01

Progress is reviewed in the following areas: electric uses; direct heat uses; drilling activities; exploration; leases; outreach and technical assistance; feasibility studies and application demonstrations; geothermal loan guarantee program; general activities; R and D activities; legal, institutional, and regulatory activities; environmental activities; and state, local, and private sector activities. Also included are a list of reports and publications and a directory of individuals in the geothermal community. (MHR)

Progress report on the varying temperature experiment

Energy Technology Data Exchange (ETDEWEB)

Qualls, A.L.; Hurst, M.T.; Raby, D.G. [Oak Ridge National Lab., TN (United States)] [and others

1997-08-01

A capsule has been designed that permits four specimen sets to be irradiated in an RB* location in the High Flux Isotope reactor (HFIR) with distinct temperature histories. During the reporting period critical component prototyping was completed. The results have lead to some design and operational changes from that previously reported. The primary design changes are (1) compression seals in the specimen holes of the beryllium holders, and (2) oxide-dispersion strengthened aluminum alloy (DISPAL) specimen sleeves in all holders. Details of the capsule design are presented in the previous issue of this publication. Four, axially displaced temperature zones are independently controlled. Holder temperatures are monitored by thermocouples and controlled by a combination of adjustable temperature control gas mixtures and auxiliary heaters. The high temperature holders are located in the center of the experimental region, which is centered on the reactor mid-plane, and the low temperature holders are located at the ends of the experimental region.

Progress report on the varying temperature experiment

International Nuclear Information System (INIS)

Qualls, A.L.; Hurst, M.T.; Raby, D.G.

1997-01-01

A capsule has been designed that permits four specimen sets to be irradiated in an RB* location in the High Flux Isotope reactor (HFIR) with distinct temperature histories. During the reporting period critical component prototyping was completed. The results have lead to some design and operational changes from that previously reported. The primary design changes are (1) compression seals in the specimen holes of the beryllium holders, and (2) oxide-dispersion strengthened aluminum alloy (DISPAL) specimen sleeves in all holders. Details of the capsule design are presented in the previous issue of this publication. Four, axially displaced temperature zones are independently controlled. Holder temperatures are monitored by thermocouples and controlled by a combination of adjustable temperature control gas mixtures and auxiliary heaters. The high temperature holders are located in the center of the experimental region, which is centered on the reactor mid-plane, and the low temperature holders are located at the ends of the experimental region

River Protection Project waste feed delivery program technical performance measurement assessment plan

International Nuclear Information System (INIS)

O'TOOLE, S.M.

1999-01-01

This plan establishes a formal technical performance-monitoring program. Technical performance is assessed by establishing requirements based performance goals at the beginning of a program and routinely evaluating progress in meeting these goals at predetermined milestones throughout the project life cycle

Integral Fast Reactor Program annual progress report, FY 1994

International Nuclear Information System (INIS)

Chang, Y.I.; Walters, L.C.; Laidler, J.J.; Pedersen, D.R.; Wade, D.C.; Lineberry, J.J.

1994-12-01

This report summarizes highlights of the technical progress made in the Integral Fast Reactor (IFR) Program in FY 1994. Technical accomplishments are presented in the following areas of the IFR technology development activities: metal fuel performance; pyroprocess development; safety experiments and analyses; core design development; fuel cycle demonstration; and LMR technology R ampersand D

Geothermal direct-heat utilization assistance. Quarterly progress report, April--June 1993

Energy Technology Data Exchange (ETDEWEB)

1993-08-01

Progress is reported on the following R&D activities: evaluation of lineshaft turbine pump problems, geothermal district heating marketing strategy, and greenhouse peaking analysis. Other activities are reported on technical assistance, technology transfer, and the geothermal progress monitor.

Integral Fast Reactor Program. Annual progress report, FY 1992

Energy Technology Data Exchange (ETDEWEB)

Chang, Y.I.; Walters, L.C.; Laidler, J.J.; Pedersen, D.R.; Wade, D.C.; Lineberry, M.J.

1993-06-01

This report summarizes highlights of the technical progress made in the Integral Fast Reactor (IFR) Program in FY 1992. Technical accomplishments are presented in the following areas of the IFR technology development activities: (1) metal fuel performance, (2) pyroprocess development, (3) safety experiments and analyses, (4) core design development, (5) fuel cycle demonstration, and (6) LMR technology R&D.

Gatlinburg conference: barometer of progress in analytical chemistry

International Nuclear Information System (INIS)

Shults, W.D.

1981-01-01

Much progress has been made in the field of analytical chemistry over the past twenty-five years. The AEC-ERDA-DOE family of laboratories contributed greatly to this progress. It is not surprising then to find a close correlation between program content of past Gatlinburg conferences and developments in analytical methodology. These conferences have proved to be a barometer of technical status

Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. Part 2. Engineering technology for geological disposal

International Nuclear Information System (INIS)

1999-11-01

Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the deep geological disposal concept for high-level radioactive wastes (HLW) in Japan. The present document, part 2 of the progress report, concerns engineering aspect with reference to Japanese geological disposal plan, according to which the vitrified HLW will be disposed of into a deep, stable rock mass with thick containers and surrounding buffer materials at the depth of several hundred meters. It discusses on multi-barrier systems consisting of a series of engineered and natural barriers that will isolate radioactive nuclides effectively and retard their migrations to the biosphere environment. Performance of repository components, including specifications of containers for vitrified HLW and their overpacks under design as well as buffer material such as Japanese bentonite to be placed in between are described referring also to such possible problems as corrosion arising from the supposed system. It also presents plans and designs for underground disposal facilities, and the presumed management of the underground facilities. (Ohno, S.)

Superconducting Machines at the Technical University of Denmark

DEFF Research Database (Denmark)

Jensen, Bogi Bech; Abrahamsen, Asger Bech; Mijatovic, Nenad

2011-01-01

Two high temperature superconducting (HTS) machine prototypes constructed at the Technical University of Denmark are presented. The construction process is presented and the excellent agreement between simulation results and experimental results are presented for one of the prototypes.......Two high temperature superconducting (HTS) machine prototypes constructed at the Technical University of Denmark are presented. The construction process is presented and the excellent agreement between simulation results and experimental results are presented for one of the prototypes....

Technical progress report for the quarter 1 October-31 December 1980

International Nuclear Information System (INIS)

1981-01-01

This report describes the technical accomplishments on the commercial nuclear waste management programs and on the geologic disposal of nuclear wastes. The program is organized into eight tasks: systems, waste package, site, repository, regulatory and institutional, test facilities and excavations, land acquisition, and program management

Development of TRITN : In-house technical information network of Technical Research Institute in The Chugoku Electric Power Co., Inc.

Science.gov (United States)

Ebara, Hisao

With the increase in information amount, progress in information network, diversified technology and change in in-house organization the Technical Research Institute has necessitated to shift the conventional technical database processing by use of personal computers into new system promised for future use. It enables to; provide classification system which meets the needs of the institute; execute distributed processing using workstations; make the low cost processing using commercial softwares; make networks using LAN, WAN personal computer communication, and provide primary materials (text data) on facsimiles using optical disks. Such features are those of technical information database system "TRITN" which is available to any persons and at any time. This paper describes how TRITN was developed and the system outline.

Office of Waste Isolation progress report, October 1976

International Nuclear Information System (INIS)

1977-01-01

Progress of the National Waste Terminal Storage program is reported under: technical projects, facility projects, systems projects, and regulatory affairs. Various media (salt, shales, rocks) for geologic storage are covered

Recent progress in sodium technology

Energy Technology Data Exchange (ETDEWEB)

Hallett, W. J.

1963-10-15

Progress over the past year in U. S. laboratories studying some of the materials and engineering problems that must be resolved in bringing the technology of sodium to an economically and technically attractive point is reviewed. The status of sodium cooled power reactors in the U. S. is described. (P.C.H.)

1984-85 ISN progress report

International Nuclear Information System (INIS)

1985-01-01

This progress report ISN 1984-1985 deals with the following subjects: nuclear physics theory, peripheral and intermediate energy physics, characteristics of reaction mechanisms in heavy ion collisions, nuclear structure, fundamental interactions, experimental methods and new instrumentation, some interdisciplinary research activities and technical activities, the SARA cyclotron and finally, technology transfer and valorisation [fr

Instrumentation of dynamic gas pulse loading system. Technical progress report, first quarter 1992

Energy Technology Data Exchange (ETDEWEB)

Mohaupt, H.

1992-04-14

The overall goal of this work is to further develop and field test a system of stimulating oil and gas wells, which increases the effective radius of the well bore so that more oil can flow into it, by recording pressure during the gas generation phase in real time so that fractures can be induced more predictably in the producing formation. Task 1: Complete the laboratory studies currently underway with the prototype model of the instrumentation currently being studied. Task 2: Perform field tests of the model in the Taft/Bakersfield area, utilizing operations closest to the engineers working on the project, and optimize the unit for various conditions encountered there. Task 3: Perform field test of the model in DGPL jobs which are scheduled in the mid-continent area, and optimize the unit for downhole conditions encountered there. Task 4: Analyze and summarize the results achieved during the complete test series, documenting the steps for usage of downhole instrumentation in the field, and compile data specifying use of the technology by others. Task 5: Prepare final report for DOE, and include also a report on the field tests completed. Describe and estimate the probability of the technology being commercialized and in what time span. The project has made substantial technical progress, though we are running about a month behind schedule. Expenditures are in line with the schedule. Increased widespread interest in the use of DGPL stimulation has kept us very busy. The computer modeling and test instrumentation developed under this program is already being applied to commercial operations.

The BGO collaboration progress report 1990

International Nuclear Information System (INIS)

Anon.

1990-01-01

A large solid angle BGO calorimeter is under contruction for photo-nuclear experiments at intermediate energy facilities. In this note the status progress of the project, the technical steps undertaken in the construction of the apparatus and the goals of this initiative are reviewed

Savannah River Plant, Works Technical Department monthly progress report for March 1956

International Nuclear Information System (INIS)

1956-01-01

This document details activities of the Works Technical Department during the month of March 1956. It covers reactor technology, separations technology, engineering assistance and heavy water technology

Technical progress report for the quarter 1 October-31 December 1980

Energy Technology Data Exchange (ETDEWEB)

1981-01-01

This report describes the technical accomplishments on the commercial nuclear waste management programs and on the geologic disposal of nuclear wastes. The program is organized into eight tasks: systems, waste package, site, repository, regulatory and institutional, test facilities and excavations, land acquisition, and program management. (DLC)

Progress and status of the Integral Fast Reactor (IFR) fuel cycle development

International Nuclear Information System (INIS)

Till, C.E.; Chang, Y.I.

1993-01-01

The Integral Fast Reactor (IFR) fuel cycle holds promise for substantial improvements in economics, diversion-resistance, and waste management. This paper discusses technical features of the IFR fuel cycle, its technical progress, the development status, and the future plans and directions

Progress and status of the Integral Fast Reactor (IFR) fuel cycle development

Energy Technology Data Exchange (ETDEWEB)

Till, C.E.; Chang, Y.I.

1993-03-01

The Integral Fast Reactor (IFR) fuel cycle holds promise for substantial improvements in economics, diversion-resistance, and waste management. This paper discusses technical features of the IFR fuel cycle, its technical progress, the development status, and the future plans and directions.

Progress and status of the Integral Fast Reactor (IFR) fuel cycle development

Energy Technology Data Exchange (ETDEWEB)

Till, C.E.; Chang, Y.I.

1993-01-01

The Integral Fast Reactor (IFR) fuel cycle holds promise for substantial improvements in economics, diversion-resistance, and waste management. This paper discusses technical features of the IFR fuel cycle, its technical progress, the development status, and the future plans and directions.

Integral Fast Reactor Program annual progress report, FY 1991

International Nuclear Information System (INIS)

1992-06-01

This report summarizes highlights of the technical progress made in the Integral Fast Reactor (IFR) Program in FY 1991. Technical accomplishments are presented in the following areas of the IFR technology development activities: (1) metal fuel performance, (2) pyroprocess development, (3) safety experiments and analyses, (4) core design development, (5) fuel cycle demonstration, and (6) LMR technology R ampersand D

Integral Fast Reactor Program. Annual progress report, FY 1993

Energy Technology Data Exchange (ETDEWEB)

Chang, Y.I.; Walters, L.C.; Laidler, J.J.; Pedersen, D.R.; Wade, D.C.; Lineberry, M.J.

1994-10-01

This report summarizes highlights of the technical progress made in the Integral Fast Reactor (IFR) Program in FY 1993. Technical accomplishments are presented in the following areas of the IFR technology development activities: (1) metal fuel performance, (2) pyroprocess development, (3) safety experiments and analyses, (4) core design development, (5) fuel cycle demonstration, and (6) LMR technology R and D.

Integral Fast Reactor Program. Annual progress report, FY 1993

International Nuclear Information System (INIS)

Chang, Y.I.; Walters, L.C.; Laidler, J.J.; Pedersen, D.R.; Wade, D.C.; Lineberry, M.J.

1994-10-01

This report summarizes highlights of the technical progress made in the Integral Fast Reactor (IFR) Program in FY 1993. Technical accomplishments are presented in the following areas of the IFR technology development activities: (1) metal fuel performance, (2) pyroprocess development, (3) safety experiments and analyses, (4) core design development, (5) fuel cycle demonstration, and (6) LMR technology R and D

Semiannual progress report for the Idaho Geothermal Program, April 1-September 30, 1981

Energy Technology Data Exchange (ETDEWEB)

Parker, J.T. (ed.)

1982-01-01

Modifications incorporated in the 5-MW Pilot Power Plant at Raft River Geothermal Test Site, system operational testing and maintenance activities at that plant, and the water treatment program's corrosion studies are summarized. Progress is reported on performance tests of the ORNL condenser and the direct-contact heat exchanger in the Prototype Power Plant. Production-injection tests associated with pump installation in monitor wells at Raft River are reported. Case studies conducted and publications prepared for the program of low-to moderate-temperature hydrothermal resource development are also reported. Monitoring activities and studies of the environmental program at Raft River are described and two new areas of research under the Environmental Support Injection Research Program: pressure monitoring, and dispersion studies. Progress of three successful proposers under the User-Coupled Confirmation Drilling Program is summarized. A program to encourage use of geothermal energy at Federal facilities was developed and initiated. Investigation of direct use of hydrothermal energy is reported. Progress is reported on the marketing Assistance Program, through which technical information and assistance are provided to potential users and developers of geothermal resources. Also reported is progress on DOE's Program Opportunity Notice (PON) Program demonstration projects and the Program Research and Development Announcement (PRDA) Program study projects.

Effects of dormancy progression and low-temperature response on changes in the sorbitol concentration in xylem sap of Japanese pear during winter season.

Science.gov (United States)

Ito, Akiko; Sugiura, Toshihiko; Sakamoto, Daisuke; Moriguchi, Takaya

2013-04-01

In order to elucidate which physiological event(s) are involved in the seasonal changes of carbohydrate dynamics during winter, we examined the effects of different low temperatures on the carbohydrate concentrations of Japanese pear (Pyrus pyrifolia (Burm.) Nakai). For four winter seasons, large increases in the sorbitol concentration of shoot xylem sap occurred during mid- to late December, possibly due to the endodormancy completion and low-temperature responses. When trees were kept at 15 °C from 3 November to 3 December in order to postpone the initiation and completion of chilling accumulation that would break endodormancy, sorbitol accumulation in xylem sap was always higher from trees with sufficient chilling accumulation than from trees that received insufficient chilling. However, an additional increase in xylem sap sorbitol occurred around late December in trees regardless of whether their chilling accumulation naturally progressed or was postponed. To examine different temperature effects more closely, we compared the carbohydrate concentrations of trees subjected to either 6 or 0 °C treatment. The sorbitol concentration in xylem sap tremendously increased at 0 °C treatment compared with 6 °C treatment. However, an additional increase in xylem sap sorbitol occurred at both the temperatures when sufficient chilling accumulated with a peak coinciding with the peak expression in shoots of the sorbitol transporter gene (PpSOT2). Interestingly, the total carbohydrate concentration of shoots tremendously increased with exposure to 0 °C compared with exposure to 6 °C, but was not affected by the amount of accumulated chilling. Instead, as chilling accumulated the ratio of sorbitol to total soluble sugars in shoots increased. We presumed that carbohydrates in the shoot tissues may be converted to sorbitol and loaded into the xylem sap so that the sorbitol accumulation patterns were synchronized with the progression of dormancy, whereas the total

Effective legal protection in the licensing of technical installations

International Nuclear Information System (INIS)

Froehler, L.

1987-01-01

Undeterminate concepts of law shall match the dynamism of technical progress in licensing technical installations (e.g. section 7, para. 2 no. 3 Atomic Energy Act). The administration and the courts have the duty to equalize normative deficits of regulation. Decrees and administrative provisions have an important impact. Administrative courts shall exercise legal protection more efficiently what e.g. can be possible after a shortening of stages of appeal. (CW) [de

Determination of aims military-technical policy of Ukraine

Directory of Open Access Journals (Sweden)

O. F. Salnikova

2014-06-01

Full Text Available In the article the aims of military-technical policy are considered. Determination of aims (tasks of military-technical policy, its maintenance, requirements to it and directions of its further development it must come true by the analysis of different factors of external and internal environment. Among such factors: geopolitical and military-political position of Ukraine and its military doctrine; realized and operating programs of development (reformation of the soldiery forming and them technical rigging; terms of future military operations and progress of their maintenance, forms, methods and characteristic signs of battle actions trend; substantive provisions of art of war; conceptions, theories and doctrines of battle application of the soldiery forming of the different states; resources dedicated by the state on development of military-technical sphere and others like that. The fundamental chart of sequence of forming of public military-technical policy is presented in the article.

The Use of Low Temperature Detectors for Direct Measurements of the Mass of the Electron Neutrino

Directory of Open Access Journals (Sweden)

A. Nucciotti

2016-01-01

Full Text Available Recent years have witnessed many exciting breakthroughs in neutrino physics. The detection of neutrino oscillations has proved that neutrinos are massive particles, but the assessment of their absolute mass scale is still an outstanding challenge in today particle physics and cosmology. Since low temperature detectors were first proposed for neutrino physics experiments in 1984, there has been tremendous technical progress: today this technique offers the high energy resolution and scalability required to perform competitive experiments challenging the lowest electron neutrino masses. This paper reviews the thirty-year effort aimed at realizing calorimetric measurements with sub-eV neutrino mass sensitivity using low temperature detectors.

Humic substances in performance assessment of nuclear waste disposal: Actinide and iodine migration in the far-field. First technical progress report

International Nuclear Information System (INIS)

Buckau, G.

2003-04-01

The present project is one in a series of research activities supported by the European Commission on the role of humic substances for the long-term safety of nuclear waste disposal. These activities started in the mid eighties within the MIRAGE project (MIgration of RAdionuclides in the GEosphere) with the most recent project being ''Effects of humic substances on the migration of radionuclides: Complexation and transport of actinides (HUMICS)'' (FI4W-CT96-0028). The HUMICS project was conducted within the fourths framework of the European Commissions research program. It started January 1997 and had a duration of three years. The results of the HUMICS project can be found in three open technical progress reports and a final report [1-4]. In analogy with the HUMICS project, the present project makes use of annual technical progress reports where individual results are published as papers in the form of annexes. By this approach, results rapidly become available to interested parties in a compact form before their publication in various scientific journals and conference proceedings. Furthermore, some of the more preliminary and/or detailed results are not likely to appear in scientific journals and proceedings. The present project is conducted within the fifths framework of the European Commissions research program. It started November 2001 and has a duration of three years. The present report covers the first project year, i.e. November 2001 to September 2002. The project is divided into eight different work packages. These are (i) ''Critical assessment of experimental methods'', (ii) ''Generation and characterization of humic substances'', (iii) ''Radionuclide humate interaction data by designed system investigations'', (iv) ''Characterization of radionuclide humate complexes'', (v) ''Natural chemical analogue studies'', (vi) ''Radionuclide transport experiments'', (vii) ''Model development'', and (viii) ''Performance assessment''. Division of work into

Progress and status of the Integral Fast Reactor (IFR) fuel cycle development

International Nuclear Information System (INIS)

Till, C.E.; Chang, Y.I.

1991-01-01

The Integral Fast Reactor (IFR) fuel cycle holds promise for substantial improvements in economics, diversion-resistance, and waste management. This paper discusses technical features of the IFR fuel cycle, its technical progress, the development status, and the future plans and directions. 10 refs

Progress and status of the Integral Fast Reactor (IFR) fuel cycle development

Energy Technology Data Exchange (ETDEWEB)

Till, C.E.; Chang, Y.I.

1991-01-01

The Integral Fast Reactor (IFR) fuel cycle holds promise for substantial improvements in economics, diversion-resistance, and waste management. This paper discusses technical features of the IFR fuel cycle, its technical progress, the development status, and the future plans and directions. 10 refs.

Progress and status of the Integral Fast Reactor (IFR) fuel cycle development

International Nuclear Information System (INIS)

Till, C.E.; Chang, Y.I.

1991-01-01

The Integral Fast Reactor (IFR) fuel cycle holds promise for substantial improvements in economics, diversion-resistance, and waste management. This paper discusses technical features of the IFR fuel cycle, its technical progress, the development status, and the future plans and directions. (author)

The Michigan high-level radioactive waste program: Final technical progress report

International Nuclear Information System (INIS)

1987-01-01

This report comprises the state of Michigan's final technical report on the location of a proposed high-level radioactive waste disposal site. Included are a list of Michigan's efforts to review the DOE proposal and a detailed report on the application of geographic information systems analysis techniques to the review process

Digital temperature meter

Energy Technology Data Exchange (ETDEWEB)

Glowacki, S

1982-01-01

Digital temperature meter for precise temperature measurements is presented. Its parts such as thermostat, voltage-frequency converter and digital frequency meter are described. Its technical parameters such as temperature range 50degC-700degC, measurement precision 1degC, measurement error +-1degC are given. (A.S.).

Site characterization progress report: Yucca Mountain, Nevada. Progress report number 17, April 1, 1997--September 30, 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-04-01

The US Department of Energy`s (DOE) Office of Civilian Radioactive Waste Management (OCRWM), created with the enactment of the Nuclear Waste Policy Act of 1982 (NWPA), is tasked to accept and dispose of the nation`s high-level radioactive waste and spent nuclear fuel in a deep geologic repository (high-level radioactive waste program). The report summarizes significant site characterization activities during the period from April 1, 1997 through September 30, 1997, in the evaluation of Yucca Mountain as a potential site for the geologic disposal of spent nuclear fuel and high-level radioactive wastes. The progress report also cites technical reports and research products that provide the detailed information on these activities. Chapter 2 outlines technical and regulatory issues that must be addressed by the Project and planned work toward achieving future objectives concerning the viability assessment, the environmental impact statement, the site recommendation, and the license application. Chapter 3 describes technical progress in preclosure radiological safety analysis, postclosure performance assessment, and performance confirmation activities. Chapter 4 describes various aspects of repository and waste package design and construction. It also discusses the Exploration Studies Facility cross drift. Chapter 5 describes site characterization activities, and Chapter 6 contains a complete list of references.

Site characterization progress report: Yucca Mountain, Nevada. Progress report number 17, April 1, 1997 - September 30, 1997

International Nuclear Information System (INIS)

1998-04-01

The US Department of Energy's (DOE) Office of Civilian Radioactive Waste Management (OCRWM), created with the enactment of the Nuclear Waste Policy Act of 1982 (NWPA), is tasked to accept and dispose of the nation's high-level radioactive waste and spent nuclear fuel in a deep geologic repository (high-level radioactive waste program). The report summarizes significant site characterization activities during the period from April 1, 1997 through September 30, 1997, in the evaluation of Yucca Mountain as a potential site for the geologic disposal of spent nuclear fuel and high-level radioactive wastes. The progress report also cites technical reports and research products that provide the detailed information on these activities. Chapter 2 outlines technical and regulatory issues that must be addressed by the Project and planned work toward achieving future objectives concerning the viability assessment, the environmental impact statement, the site recommendation, and the license application. Chapter 3 describes technical progress in preclosure radiological safety analysis, postclosure performance assessment, and performance confirmation activities. Chapter 4 describes various aspects of repository and waste package design and construction. It also discusses the Exploration Studies Facility cross drift. Chapter 5 describes site characterization activities, and Chapter 6 contains a complete list of references

Significance of technical rules for environmental pollution control

International Nuclear Information System (INIS)

Grefen, K.

1989-01-01

Technical rules for environmental pollution control are very important in times of intensified technical progress and especially in view of the alterations of the legislative basis of the European Market in 1992. In the fields of jurisprudence, science and technology they serve as a decision-making aid for authorities, specialists in plant development and operation and the preparatory stages of international legislation. The topic is explained by the development of guidelines with the VDI-Commission on Air Pollution Prevention. (orig.) [de

Progress report on the influence of higher interpass temperatures on the integrity of austenitic stainless steel welded joints

Energy Technology Data Exchange (ETDEWEB)

Yarmuch, M.; Choi, L. [Alberta Research Council, Edmonton, AB (Canada); Armstrong, K.; Radu, I. [PCL Industrial Constructors Inc., Nisku, AB (Canada)

2008-07-01

This report discussed the progress of the Welding Productivity Group (TWPG) interpass temperature assessment project (ITAP). The project was initiated to evaluate the influence of interpass temperatures on the metallurgical, corrosive, and mechanical properties of austenitic stainless steel, carbon steel, and low-alloy pressure weldments. To date, the project has conducted experiments to determine if interpass temperatures in austenitic stainless steel weldments are higher than temperatures recommended by API requirements. Elevated interpass temperatures for various base materials have been evaluated. Preliminary metallurgical, mechanical, and laboratory corrosion data from 3 experiments with 304/304L and 316/316L stainless steel weldment test specimens has shown that no significant changes occur as a result of elevated interpass temperatures. Results from side bend specimens have demonstrated that elevated interpass temperatures produce acceptable weldment ductility. No intergranular cracking was observed during oxalic acid etch tests conducted for the 316/316L samples. Huey tests performed on the 304/304L specimens indicated that elevated interpass temperatures did not adversely affect the intergranular corrosion resistance of weldments with less than 3 weld passes. Huey tests performed on the 316 specimens showed a marked increase in corrosion rates and normalized weight losses. It was concluded that rates of attack correlate with the maximum interpass temperature and not the average weld metal ferrite number. 22 refs., 11 tabs., 12 figs.

TECHNICAL COORDINATION

CERN Multimedia

Austin Ball

Summary of progress since last CMS week. Ten years of construction work have been completed. CMS is closed, in very close to the ideal low luminosity configuration, and performed well in the first tests with LHC beam. Behind this encouraging news is the story of a summer of intense commitment by many teams (from the collaboration and 3 CERN departments) working together, against the clock and despite many minor setbacks, to ensure that the experiment was ready to play a leading role in the excitement of September 10. Following beampipe bakeout and refill with pure neon, a magnificent effort by the ECAL group and the pt 5 technical crew made it possible to install and commission all 4 ECAL endcap Dees before the end of August. In the shadow of this activity, the barrel and forward pixel trackers and part of the beam monitoring were installed within the vac tank. The pt 5 technical teams then succeeded in safely removing the 20t installation tables and their support blocks from beneath the already installed ...

Activity Progress report 1982-1985

International Nuclear Information System (INIS)

1986-01-01

This reports gives a summary of all activities of the Elementary Particle Physics Department at Saclay between the beginning of 1982 and the end of 1985. The experiments in progress or in preparation are presented by subject. The main technical studies and achievements are also described. Finally lists of publications and information concerning Department organization are given [fr

Recent progress in low-temperature silicon detectors

International Nuclear Information System (INIS)

Abreu, M.; D'Ambrosio, N.; Bell, W.; Berglund, P.; Borchi, E.; Boer, W. de; Borer, K.; Bruzzi, M.; Buontempo, S.; Casagrande, L.; Chapuy, S.; Cindro, V.; Devine, S.R.H.; Dezillie, B.; Dierlamm, A.; Dimcovski, Z.; Eremin, V.; Esposito, A.; Granata, V.; Grigoriev, E.; Grohmann, S.; Hauler, F.; Heijne, E.; Heising, S.; Hempel, O.; Herzog, R.; Haerkoenen, J.; Janos, S.; Jungermann, L.; Konorov, I.; Li, Z.; Lourenco, C.; De Masi, R.; Menichelli, D.; Mikuz, M.; Niinikoski, T.O.; O'Shea, V.; Pagano, S.; Palmieri, V.G.; Paul, S.; Pretzl, K.; Smith, K.; Solano, B. Pere; Sousa, P.; Pirollo, S.; Rato Mendes, P.; Ruggiero, G.; Sonderegger, P.; Tuominen, E.; Verbitskaya, E.; Da Via, C.; Watts, S.; Wobst, E.; Zavrtanik, M.

2003-01-01

The CERN RD39 Collaboration studies the possibility to extend the detector lifetime in a hostile radiation environment by operating them at low temperatures. The outstanding illustration is the Lazarus effect, which showed a broad operational temperature range around 130 K for neutron irradiated silicon detectors

Gas-Cooled Thermal Reactor Program. Annual technical progress report for the period ending September 30, 1981

International Nuclear Information System (INIS)

1982-03-01

This report provides descriptions and results of the technical effort during FY81 on the Gas-Cooled Thermal Reactor Program. The FY81 work was organized according to the Work Breakdown Structure (WBS) for the National HTGR Program, and fell within five of the WBS tasks. The work on Market Definition and Development (WBS 03) was associated with estimating product costs for HTGR systems and their alternatives, projecting markets and market penetrations for these systems, and providing costs and market input to application analyses and component design. The Plant Technology (WBS 13) effort was mainly in the development of the systems dynamic computer code, STAR, for the transient analysis of HTGR's in reformer applications. The analysis of pebble bed reactors (PBR) was performed under Technology Transfer (WBS 15). The effort on components and systems within the nuclear heat source for reforming plants was performed under High Temperature Nuclear Heat Source (WBS 42)

A Simple extension of Dematerialization Theory: Incorporation of Technical Progress and the Rebound Effect

OpenAIRE

Magee, Christopher L.; Devezas, Tessaleno C.

2016-01-01

Dematerialization is the reduction in the quantity of materials needed to produce something useful over time. Dematerialization fundamentally derives from ongoing increases in technical performance but it can be counteracted by demand rebound - increases in usage because of increased value (or decreased cost) that also results from increasing technical performance. A major question then is to what extent technological performance improvement can offset and is offsetting continuously increasin...

Electronic refrigerant leak detector. Quarterly technical progress report

Energy Technology Data Exchange (ETDEWEB)

Talamas, E. Jr.

1998-10-15

The project comprises three main tasks. They are (1) Develop, design, and fabricate sensors, (2) Develop, design, and fabricate test instruments, (3) Testing and data analysis. The milestone includes 17 sub-tasks for the 52-weeks project period, starting on May 1, 1998 and ending on April 30, 1999. As stated in the Application for Federal Assistance, Micronic intended to relocate to a new office by June of 1998. This decision was delayed, since the first partial payment was transferred on August 12, 1998. Micronic plans to relocate this November. A second Provisional Application for a US patent has been filed. Progress made during this period is reported.

Professional Technical Standards in Colleges and Schools of Pharmacy

Science.gov (United States)

Berry, Tricia M.; Chichester, Clinton O.; Sanoski, Cynthia A.; Woodward, Donald A.; Worley, Marcia M.; Early, Johnnie L.

2011-01-01

Objective To determine the prevalence, characteristics, and use of professional technical standards among colleges and schools of pharmacy accredited by the Accreditation Council for Pharmacy Education (ACPE). Methods The Web site of every college and school of pharmacy accredited by ACPE was searched to identify information regarding the availability, content, and use of technical standards and to obtain demographic information. Results Information was obtained from all of the 114 colleges and schools of pharmacy and 67 (59%) had technical standards in place. Common themes for technical standards were: observation; communication; motor; intellectual, conceptual, integrative and quantitative abilities; and behavioral and social attributes. Of those colleges and schools with technical standards, 61 (91%) had standards that addressed all 5 of these themes and 34 (51%) specified that the technical standards were used in their admission, progression, and graduation procedures. Conclusion More than half of the colleges and schools of pharmacy examined in this study have technical standards; however, 41% have yet to develop and implement them. Colleges and schools of pharmacy looking for guidance in technical standards development could use the technical standards themes identified in this study. PMID:21655404

Coal to SNG: Technical progress, modeling and system optimization through exergy analysis

International Nuclear Information System (INIS)

Li, Sheng; Ji, Xiaozhou; Zhang, Xiaosong; Gao, Lin; Jin, Hongguang

2014-01-01

Highlights: • Technical progresses of coal to SNG technologies are reported. • The entire coal to SNG system is modeled. • Coupling between SNG production and power generation is investigated. • Breakthrough points for further energy saving are determined. • System performance is optimized based on the first and second laws of thermodynamics. - Abstract: For both energy security and CO 2 emission reduction, synthetic natural gas (SNG) production from coal is an important path to implement clean coal technologies in China. In this paper, an overview of the progress of coal to SNG technologies, including the development of catalysts, reactor designs, synthesis processes, and systems integration, is provided. The coal to SNG system is modeled, the coupling between SNG production and power generation is investigated, the breakthrough points for further energy savings are determined, and the system performance is optimized based on the first and the second laws of thermodynamics. From the viewpoint of the first law of thermodynamics, the energy conversion efficiency of coal to SNG system can reach 59.8%. To reduce the plant auxiliary power, the breakthrough points are the development of low-energy-consumption oxygen production technology and gas purification technology or seeking new oxidants for coal gasification instead of oxygen. From the viewpoint of the second law of thermodynamics, the major exergy destruction in a coal to SNG system occurs in the coal gasification unit, SNG synthesis unit and the raw syngas cooling process. How to reduce the exergy destruction in these units is the key to energy savings and system performance enhancement. The conversion ratio of the first SNG synthesis reactor and the split ratio of the recycle gas are key factors that determine the performance of both the SNG synthesis process and the whole plant. A “turning point” phenomenon is observed: when the split ratio is higher than 0.90, the exergy destruction of the SNG

Power systems development facility. Quarterly technical progress report, July 1--September 30, 1993

Energy Technology Data Exchange (ETDEWEB)

1993-12-31

This quarterly technical progress report summarizes work completed during the Second Quarter of the Second Budget Period, July 1 through September 30, 1993, under the Department of Energy (DOE) Cooperative Agreement No. DE-FC21-90MC25140 entitled ``Hot Gas Cleanup Test Facility for Gasification and Pressurized Combustion.`` The objective of this project is to evaluate hot gas particle control technologies using coal-derived gas streams. This will entail the design, construction, installation, and use of a flexible test facility which can operate under realistic gasification and combustion conditions. The major particulate control device issues to be addressed include the integration of the particulate control devices into coal utilization systems, on-line cleaning techniques, chemical and thermal degradation of components, fatigue or structural failures, blinding, collection efficiency as a function of particle size, and scaleup of particulate control systems to commercial size. The conceptual design of the facility was extended to include a within scope, phased expansion of the existing Hot Gas Cleanup Test Facility Cooperative Agreement to also address systems integration issues of hot particulate removal in advanced coal-based power generation systems. This expansion included the consideration of the following modules at the test facility in addition to the existing Transport Reactor gas source and Hot Gas Cleanup Units: Carbonizer/Pressurized Circulating Fluidized Bed Gas Source. Hot Gas Cleanup Units to mate to all gas streams; Combustion Gas Turbine; and Fuel Cell and associated gas treatment. This expansion to the Hot Gas Cleanup Test Facility is herein referred to as the Power Systems Development Facility (PSDF). The major emphasis during this reporting period was continuing the detailed design of the facility.

Scientific progress as increasing verisimilitude.

Science.gov (United States)

Niiniluoto, Ilkka

2014-06-01

According to the foundationalist picture, shared by many rationalists and positivist empiricists, science makes cognitive progress by accumulating justified truths. Fallibilists, who point out that complete certainty cannot be achieved in empirical science, can still argue that even successions of false theories may progress toward the truth. This proposal was supported by Karl Popper with his notion of truthlikeness or verisimilitude. Popper's own technical definition failed, but the idea that scientific progress means increasing truthlikeness can be expressed by defining degrees of truthlikeness in terms of similarities between states of affairs. This paper defends the verisimilitude approach against Alexander Bird who argues that the "semantic" definition (in terms of truth or truthlikeness alone) is not sufficient to define progress, but the "epistemic" definition referring to justification and knowledge is more adequate. Here Bird ignores the crucial distinction between real progress and estimated progress, explicated by the difference between absolute (and usually unknown) degrees of truthlikeness and their evidence-relative expected values. Further, it is argued that Bird's idea of returning to the cumulative model of growth requires an implausible trick of transforming past false theories into true ones.

Private sector involvement in the US program of technical assistance to IAEA safeguards

International Nuclear Information System (INIS)

Pepper, S.E.; Epel, L.; Maise, G.; Reisman, A.; Skalyo, J.

1995-01-01

The US Program of Technical Assistance to IAEA Safeguards (POTAS) relies on technical expertise found in the U. S private and public sectors. Since 1993, the international Safeguards Project Office (ISPO) has sought to increase the role of the private sector in POTAS. ISPO maintains and continues to develop a database of US companies interested in providing technical expertise to the IAEA. This database is used by ISPO to find appropriate contractors to respond to IAEA requests for technical assistance when the assistance can be provided by the private sector. The private sector is currently providing support in the development of equipment, training, and procedure preparation. POTAS also supports the work of private consultants. This paper discusses ISPO's efforts to identify suitable vendors and discusses conditions that hinder more substantial involvement by the private sector. In addition, the paper will discuss selected projects that are currently in progress and identify common problems that impede the progress and success of tasks performed by the private sector

Progress of the HTR-10 project

International Nuclear Information System (INIS)

Zhong, D.; Xu, Y.

1996-01-01

This paper briefly introduces the main technical features and the design specifications of the HTR-10. Present status and main progress of the license applications, the design and manufacture of the main components and the engineering experiments as well as the construction of the HTR-10 are summarized. (author). 3 tabs

Tanks Focus Area FY98 midyear technical review

Energy Technology Data Exchange (ETDEWEB)

Schlahta, S.N.; Brouns, T.M.

1998-06-01

The Tanks Focus Area (TFA) serves as the DOE`s Office of Environmental Management`s national technology and solution development program for radioactive waste tank remediation. Its technical scope covers the major functions that comprise a complete tank remediation system: waste retrieval, waste pretreatment, waste immobilization, tank closure, and characterization of both the waste and tank with safety integrated into all the functions. In total, 17 technologies and technical solutions were selected for review. The purpose of each review was to understand the state of development of each technology selected for review and to identify issues to be resolved before the technology or technical solution progressed to the next level of maturity. The reviewers provided detailed technical and programmatic recommendations and comments. The disposition of these recommendations and comments and their impact on the program is documented in this report.

Tanks Focus Area FY98 midyear technical review

International Nuclear Information System (INIS)

Schlahta, S.N.; Brouns, T.M.

1998-06-01

The Tanks Focus Area (TFA) serves as the DOE's Office of Environmental Management's national technology and solution development program for radioactive waste tank remediation. Its technical scope covers the major functions that comprise a complete tank remediation system: waste retrieval, waste pretreatment, waste immobilization, tank closure, and characterization of both the waste and tank with safety integrated into all the functions. In total, 17 technologies and technical solutions were selected for review. The purpose of each review was to understand the state of development of each technology selected for review and to identify issues to be resolved before the technology or technical solution progressed to the next level of maturity. The reviewers provided detailed technical and programmatic recommendations and comments. The disposition of these recommendations and comments and their impact on the program is documented in this report

Technical basis for storage of Zircaloy-clad spent fuel in inert gases

International Nuclear Information System (INIS)

Johnson, A.B. Jr.; Gilbert, E.R.

1983-09-01

The technical bases to establish safe conditions for dry storage of Zircaloy-clad fuel are summarized. Dry storage of fuel with zirconium alloy cladding has been licensed in Canada, the Federal Republic of Germany, and Switzerland. Dry storage demonstrations, hot cell tests, and modeling have been conducted using Zircaloy-clad fuel. The demonstrations have included irradiated boiling water reactor, pressurized heavy-water reactor, and pressurized water reactor fuel assemblies. Irradiated fuel has been emplaced in and retrieved from metal casks, dry wells, silos, and a vault. Dry storage tests and demonstrations have involved about 15,000 fuel rods, and about 5600 rods have been monitored during dry storage in inert gases with maximum cladding temperatures ranging from 50 to 570 0 C. Although some tests and demonstrations are still in progress, there is currently no evidence that any rods exposed to inert gases have failed (one PWR rod exposed to an air cover gas failed at about 270 0 C). Based on this favorable experience, it is concluded that there is sufficient information on fuel rod behavior, storage conditions, and potential cladding failure mechanisms to support licensing of dry storage in the US. This licensing position includes a requirement for inert cover gases and a maximum cladding temperature guideline of 380 0 C for Zircaloy-clad fuel. Using an inert cover gas assures that even if fuel with cladding defects were placed in dry storage, or if defects develop during storage, the defects would not propagate. Tests and demonstrations involving Zircaloy-clad rods and assemblies with maximum cladding temperatures above 400 0 C are in progress. When the results from these tests have been evaluated, the viability of higher temperature limits should be examined. Acceptable conditions for storage in air and dry storage of consolidated fuel are issues yet to be resolved

Chemistry of gaseous lower-valent actinide halides. Technical progress report

International Nuclear Information System (INIS)

Hildenbrand, D.L.

1984-01-01

Objective is to provide thermochemical data for key actinide halide and oxyhalide systems. Progress is reported on bond dissociation energies of gaseous ThCl 4 , ThCl 3 , ThCl 2 , and ThCl; bond dissociation energies of ruthenium fluorides; and mass spectroscopy of UF 6

Jet Joint Undertaking. Progress report 1990

International Nuclear Information System (INIS)

1991-03-01

This JET Progress Reports provides an overview summary and puts into context the scientific and technical advances made on JET during 1990. In addition, the Report is supplemented by appendices of contributions (in preprint form) of the more important JET articles published during the year, which set out the details of JET activities

Geothermal Progress Monitor Report No. 2, January/February 1980

Energy Technology Data Exchange (ETDEWEB)

1980-01-01

Progress is reviewed in the following aspects of the program: electrical uses; direct-heat uses; leases; outreach and technical assistance; general activities; legal, institutional, and regulatory activities; and reports and publications. (MHR)

Technical and tactical soccer players' performance in conceptual small-sided games

Directory of Open Access Journals (Sweden)

Cristian Javier Ramirez Lizana

2015-09-01

Full Text Available AbstractConceptual small-sided games (CSSGs may be interesting as a methodology for training soccer players given its connection to the unpredictability that is inherent to soccer. Our aim was investigate, through videogrammetry, if the technical and tactical principles promoted through the adoption of distinct rules from two distinct CSSGs (maintaining ball possession; and progression to the target would actually be achieved. The study included 24 athletes assigned to 6-player teams. Our data showed that the CSSGs' organising principles create situations with differing levels of difficulty that obey the propositions of maintaining ball possession and progression to the target, i.e., CSSGs permit systematic training on technical and tactical components in order to emphasize the concepts adopted in this study in games context. Our data credit the CSSGs for teaching technical and tactical lessons that, when coupled with adequate physical conditioning, can facilitate a player's capacity to merge thoughts and events in different situations.

Quarterly technical progress report, February 1, 1996--April 30, 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-05-28

This report from the Amarillo National REsource Center for PLutonium provides research highlights and provides information regarding the public dissemination of information. The center is a a scientific resource for information regarding the issues of the storage, disposition, potential utilization and transport of plutonium, high explosives, and other hazardous materials generated from nuclear weapons dismantlement. The center responds to informational needs and interpretation of technical and scientific data raised by interested parties and advisory groups. Also, research efforts are carried out on remedial action programs and biological/agricultural studies.

Technical aspects of high converter reactors

International Nuclear Information System (INIS)

1992-02-01

The meeting provided an opportunity to review and discuss national R and D programs, various technical aspects of and worldwide progress in the implementation of high conversion reactors. The meeting was attended by 66 participants from 18 countries and 2 international organizations. 33 papers were presented. A separate abstract was prepared for each of these papers. Refs, figs, tabs, slides and diagram

Proceedings: Computer Science and Data Systems Technical Symposium, volume 1

Science.gov (United States)

Larsen, Ronald L.; Wallgren, Kenneth

1985-01-01

Progress reports and technical updates of programs being performed by NASA centers are covered. Presentations in viewgraph form are included for topics in three categories: computer science, data systems and space station applications.

The 1988 progress report of the Nuclear Safety and Protection Institut

International Nuclear Information System (INIS)

Anon.

1988-01-01

The 1988 progress report of the Nuclear Safety and Protection Institut (CEA, France). The Institute's fields of action involve: The activities and technical safety of the nuclear power plants, the environmental and human radiation protection which includes technical, health and medical aspects, the nuclear materials compatibility and control and the accident intervention actions. The 1988 Institute activities are characterized by the continuity of the previous technical safety directives, by the improvement of the nuclear risk communication and of the international cooperation [fr

Development of incident progress prediction technologies for nuclear emergency preparedness. Current status and future subjects

International Nuclear Information System (INIS)

Yoshida, Yoshitaka; Yamamoto, Yasunori; Kusunoki, Takayoshi; Kawasaki, Ikuo; Yanagi, Chihiro; Kinoshita, Ikuo; Iwasaki, Yoshito

2014-01-01

Nuclear licensees are required to maintain a prediction system during normal condition for using a nuclear emergency by the Basic Plan for Disaster Prevention of government. With prediction of the incident progress, if the present condition of nuclear power plant is understood appropriately and it grows more serious with keeping the present situation, it is in predicting what kind of situation will be occurred in the near future, choosing the effective countermeasures against the coming threat, and understanding the time available of intervention time. Following the accident on September 30 1999 in the nuclear fuel fabrication facility in Tokai Village of Ibaraki Prefecture, the Institute of Nuclear Safety System started development of incident progress prediction technologies for nuclear emergency preparedness. We have performed technical applications and made improvements in nuclear emergency exercises and verified the developed systems using the observed values of the Fukushima Daiichi Nuclear Power Plant accident. As a result, our developed Incident Progress Prediction System was applied to nuclear emergency exercises and we accumulated knowledge and experience by which we improved the system to make predictions more rapidly and more precisely, including for example, the development of a prediction method for leak size of reactor coolant. On the other hand, if a rapidly progressing incident occurs, since end users need simple and quick predictions about the public's protection and evacuation areas, we developed the Radioactive Materials Release, Radiation Dose and Radiological Protection Area Prediction System which changed solving an inverse problem into a forward problem solution. In view of the water-level-decline incident of the spent fuel storage facility at the Fukushima Daiichi Nuclear Power Plant, the spent fuel storage facility water level and the water temperature evaluation tool were improved. Such incident progress prediction technologies were

100 Areas technical activities report, engineers - March 1951

Energy Technology Data Exchange (ETDEWEB)

1951-04-01

This is the monthly 100 areas technical activities report from the engineering division for the month of March 1951. It reports on engineering activities related directly to the different production reactors, and gives progress reports on various engineering projects which are in development by the engineering group.

Bioethics for Technical Experts

Science.gov (United States)

Asano, Shigetaka

Along with rapidly expanding applications of life science and technology, technical experts have been implicated more and more often with ethical, social, and legal problems than before. It should be noted that in this background there are scientific and social uncertainty elements which are inevitable during the progress of life science in addition to the historically-established social unreliability to scientists and engineers. In order to solve these problems, therefore, we should establish the social governance with ‘relief’ and ‘reliance’ which enables for both citizens and engineers to share the awareness of the issues, to design social orders and criterions based on hypothetical sense of values for bioethics, to carry out practical use management of each subject carefully, and to improve the sense of values from hypothetical to universal. Concerning these measures, the technical experts can learn many things from the present performance in the medical field.

Technical Progress and Development Directions of Oceanic Spatial Information Datum

Directory of Open Access Journals (Sweden)

BAO Jingyang

2017-10-01

Full Text Available This paper briefly analyzes the basic development and technical situation of oceanic spatial information datum, reviews the main processes of oceanic vertical datum and correlative oceanic tidal study, such as improvement and perfect methods of determining tidal station vertical datum, realizing form of vertical datum controlled by tidal station, effect on maintaining vertical datum by long-term tidal station, oceanic tidal model establishing, and also construction and transformation of tidal datum, and then forecasts the key development directions of oceanic spatial information datum on high-accuracy marine position service, vertical datum and the transferring model refinement and spatial datum application.

Technical evaluation of the electrical, instrumentation, and control design aspects of the low temperature overpressure protection system for the Yankee Rowe nuclear power plant

International Nuclear Information System (INIS)

Latorre, V.R.; Mayn, B.G.

1979-08-01

This report documents the technical evaluation of the electrical, instrumentation, and control design aspects for the low temperature overpressure protection system of the Yankee Rowe nuclear power plant. Design basis criteria used to evaluate the acceptability of the system included operator action, system testability, single failure criterion, and seismic Category I and IEEE Std-279-1971 criteria

Technical evaluation of the electrical, instrumentation, and control design aspects of the low temperature overpressure protection system for the Maine Yankee nuclear power plant

International Nuclear Information System (INIS)

Latorre, V.R.; Mayn, B.G.

1979-08-01

This report documents the technical evaluation of the electrical, instrumentation, and control design aspects for the low temperature overpressure protection system of the Maine Yankee nuclear power plant. Design basis criteria used to evaluate the acceptability of the system included operator action, system testability, single failure criterion, and seismic Category I and IEEE Std-279-1971 criteria

Bench-scale testing of on-line control of column flotation using a novel analyzer. Third quarterly technical progress report, April 1, 1993--June 30, 1993

Energy Technology Data Exchange (ETDEWEB)

1993-08-24

This document contains the third quarterly technical progress report for PTI`s Bench-Scale Testing Project of a circuit integrating PTI`s KEN-FLOTETM Column Flotation Technology and PTI`s On-Line Quality Monitor and Control System. The twelve-month project involves installation and testing of a 200--300 lb/hr. bench-scale flotation circuit at PETC`s Coal Preparation Process Research Facility (CPPRF) for two bituminous coals (Upper Freeport and Pittsburgh No. 8 Seam Raw Coals). Figure 1 contains the project plan, as well as the approach to completing the major tasks within the twelve-month project schedule. The project is broken down into three phases, which include: Phase I -- Preparation: The preparation phase was performed principally at PTI`s Calumet offices from October through December, 1992. It involved building of the equipment and circuitry, as well as some preliminary design and equipment testing; Phase II -- ET Circuit Installation and Testing: This installation and testing phase of the project was performed at PETC`s CPPRF from January through June, 1993, and was the major focus of the project. It involved testing of the continuous 200--300 lb/hr. circuit; and Phase III -- Project Finalization: The project finalization phase is occurring from July through September, 1993, at PTI`s Calumet offices and involves finalizing analytical work and data evaluation, as well as final project reporting. This Third Quarterly Technical Progress Report principally summarizes the results from the benchscale testing with the second coal (Pittsburgh No. 8 Seam Coal), which occurred in April through June, 1993. It also contains preliminary economic evaluations that will go into the Final Report, as well as the plan for the final reporting task.

Study Progress of Physiological Responses in High Temperature Environment

Science.gov (United States)

Li, K.; Zheng, G. Z.; Bu, W. T.; Wang, Y. J.; Lu, Y. Z.

2017-10-01

Certain workers are exposed to high temperatures for a long time. Heat stress will result in a series of physiological responses, and cause adverse effects on the health and safety of workers. This paper summarizes the physiological changes of cardiovascular system, core temperature, skin temperature, water-electrolyte metabolism, alimentary system, neuroendocrine system, reaction time and thermal fatigue in high temperature environments. It can provide a theoretical guidance for labor safety in high temperature environment.

Proceedings: Computer Science and Data Systems Technical Symposium, volume 2

Science.gov (United States)

Larsen, Ronald L.; Wallgren, Kenneth

1985-01-01

Progress reports and technical updates of programs being performed by NASA centers are covered. Presentations in viewgraph form, along with abstracts, are included for topics in three catagories: computer science, data systems, and space station applications.

Sensitivity of climate change mitigation estimates to assumptions about technical change

International Nuclear Information System (INIS)

Dowlatabadi, H.

1998-01-01

With greater certainty in anthropogenic influence on observed changes in climate there is increasing pressure for agreements to control emissions of greenhouse gases ([HOUGHTON]). While it is difficult to assess the appropriate level of mitigation, it has been argued that flexibility in meeting emission targets offers significant economic savings. Such flexibility can be exercised in terms of timing of mitigation (i.e. delay) or geographic location of the intervention (e.g. permit trading and Joint-Implementation). Much of this insight is based on standard models of technical change in energy supply and demand. However, standard model formulations rarely consider: (i) a link between the pattern of technical change and policy interventions; (ii) economies of learning; and (iii) technical progress in discovery and recovery of oil and gas. While there is evidence to support the importance of these factors in historic patterns of technical progress, the data necessary to calibrate internally consistent economic models of these phenomena have not been available. In this paper simple representations of endogenous and induced technical change have been used to explore the sensitivity of mitigation cost estimates to how technical change is represented in energy economics models. The scenarios involve control of CO 2 emissions to limit its concentration to no more than 550 ppm(v), starting in the year 2000, and delayed to 2025. This sensitivity analysis has revealed four robust insights: (i) If endogenous technical change is assumed, expected business as usual emissions are higher than otherwise estimated - nevertheless, while 25% greater CO 2 control is required for meeting the CO 2 concentration target, the cost of mitigation is 40% lower; (ii) If technical progress in oil and gas discovery and recovery is assumed, energy use and CO 2 emissions increase by 75% and 65%, respectively above the standard estimates; (iii) If the economies of learning exhibited in various

World progress toward fusion energy

International Nuclear Information System (INIS)

Davies, N.A.

1989-01-01

The author discusses international progress in fusion research during the last three years. Much of the technical progress has been achieved through international collaboration in magnetic fusion research. This progress has stimulated political interest in a multinational effort, aimed at designing and possibly constructing the world's first experimental fusion reactor. This interest was reflected in recent summit-level discussions involving President Mitterand, General Secretary Gorbachev, and President Reagan. Most recently, the European Community (EC), Japan, the United States, and the U.S.S.R. have decided to begin serious preparation for taking the next step toward practical fusion energy. These parties have agreed to begin the design and supporting R and D for an International Thermonuclear Experimental Reactor (ITER) under the auspices of the International Atomic Energy Agency (IAEA). The initiation of this international program to prepare for a fusion test reactor is discussed

Low-temperature nuclear heat applications: Nuclear power plants for district heating

International Nuclear Information System (INIS)

1987-08-01

The IAEA reflected the needs of its Member States for the exchange of information in the field of nuclear heat application already in the late 1970s. In the early 1980s, some Member States showed their interest in the use of heat from electricity producing nuclear power plants and in the development of nuclear heating plants. Accordingly, a technical committee meeting with a workshop was organized in 1983 to review the status of nuclear heat application which confirmed both the progress made in this field and the renewed interest of Member States in an active exchange of information about this subject. In 1985 an Advisory Group summarized the Potential of Low-Temperature Nuclear Heat Application; the relevant Technical Document reviewing the situation in the IAEA's Member States was issued in 1986 (IAEA-TECDOC-397). Programme plans were made for 1986-88 and the IAEA was asked to promote the exchange of information, with specific emphasis on the design criteria, operating experience, safety requirements and specifications for heat-only reactors, co-generation plants and power plants adapted for heat application. Because of a growing interest of the IAEA's Member States about nuclear heat employment in the district heating domaine, an Advisory Group meeting was organized by the IAEA on ''Low-Temperature Nuclear Heat Application: Nuclear Power Plants for District Heating'' in Prague, Czechoslovakia in June 1986. The information gained up to 1986 and discussed during this meeting is embodied in the present Technical Document. 22 figs, 11 tabs

US/Japan collaborative program on fusion reactor materials: Summary of the tenth DOE/JAERI Annex I technical progress meeting on neutron irradiation effects in first wall and blanket structural materials

International Nuclear Information System (INIS)

Rowcliffe, A.F.

1989-01-01

This meeting was held at Oak Ridge National Laboratory on March 17, 1989, to review the technical progress on the collaborative DOE/JAERI program on fusion reactor materials. The purpose of the program is to determine the effects of neutron irradiation on the mechanical behavior and dimensional stability of US and Japanese austenitic stainless steels. Phase I of the program focused on the effects of high concentrations of helium on the tensile, fatigue, and swelling properties of both US and Japanese alloys. In Phase II of the program, spectral and isotropic tailoring techniques are fully utilized to reproduce the helium:dpa ratio typical of the fusion environment. The Phase II program hinges on a restart of the High Flux Isotope Reactor by mid-1989. Eight target position capsules and two RB* position capsules have been assembled. The target capsule experiments will address issues relating to the performance of austenitic steels at high damage levels including an assessment of the performance of a variety of weld materials. The RB* capsules will provide a unique and important set of data on the behavior of austenitic steels irradiated under conditions which reproduce the damage rate, dose, temperature, and helium generation rate expected in the first wall and blanket structure of the International Thermonuclear Experimental Reactor

High-temperature superconductors make major progress

CERN Multimedia

CERN Bulletin

2014-01-01

This month's Nature Materials featured an important breakthrough for high-temperature superconductors. A new method has been found for processing Bi-2212 high-temperature superconducting round wire in order to drastically increase its critical current density. The result confirms that this conductor is a serious candidate for future very-high-field magnets.   This image shows the cross-section of two Bi-2212 wires. The bottom wire has less leakage and void porosity due to a heat treatment done at an overpressure of 100 bar - about 100 times the pressure used to produce the top wire (image from [Nature Materials, Vol. 13 (2014), 10.1038/nmat3887]). The workhorse for building superconducting accelerator magnets has been, so far, the Niobium-Titanium (Nb-Ti) alloy superconductor. But with Nb-Ti having reached its full potential, other conductors must be used to operate in higher magnetic fields beyond those reached with the LHC magnets. Today, the intermetallic Niobium-Tin (Nb3Sn) is th...

Fifth technical meeting on quality

International Nuclear Information System (INIS)

Girard, A.

1998-01-01

This article reports on the 5th Technical Meeting on Quality which was held in San Diego on 20-22 October 1997 and which was attended by representatives of the Home and Joint Central Team and of manufacturers currently involved in the Large R and D projects. The meeting made progress towards the finalization of the ITER Quality Manual document for inclusion in the Final Design Report and the definition of the quality necessary for ITER procurement and construction

Environmental Research Division technical progress report: January 1986--October 1987

International Nuclear Information System (INIS)

1988-07-01

Technical process in the various research activities of Argonne National Laboratory's Environmental Research Division is reported for the period 1986-1987. Textual, graphic, and tabular information is used to briefly summarize (in separate chapters) the work of the Division's Atmospheric Physics, Environmental Effects Research, Fundamental Molecular Physics and Chemistry, and Organic Geochemistry and Environmental Instrumentation Programs. Information on professional qualifications, awards, and outstanding professional activities of staff members, as well as lists of publications, oral presentations, special events organized, and participants in educational programs, are provided in appendices at the end of each chapter. Individual projects under each division are processed separately for the data bases

Environmental Research Division technical progress report: January 1986--October 1987

Energy Technology Data Exchange (ETDEWEB)

1988-07-01

Technical process in the various research activities of Argonne National Laboratory's Environmental Research Division is reported for the period 1986-1987. Textual, graphic, and tabular information is used to briefly summarize (in separate chapters) the work of the Division's Atmospheric Physics, Environmental Effects Research, Fundamental Molecular Physics and Chemistry, and Organic Geochemistry and Environmental Instrumentation Programs. Information on professional qualifications, awards, and outstanding professional activities of staff members, as well as lists of publications, oral presentations, special events organized, and participants in educational programs, are provided in appendices at the end of each chapter. Individual projects under each division are processed separately for the data bases.

Problems of Technical Electrodynamics (Selected Articles),

Science.gov (United States)

1984-04-11

copy available. ii DC 83143001 PAGE 1 PROBLEMS OF TECHNICAL ELECTRODYNAMICS. DOC - 83143001 PAGE 2 In the collector /collection are connected the...composite/ compound reliable in mechanical sense forgings of rotors with a weight of 250 t and it is more and rotor binding bands. These K forgings must be...go - calculated coefficient, which considers the character of temperature field. With a linear change in temperature .=1, with parabolic =3

Technical writing versus technical writing

Science.gov (United States)

Dillingham, J. W.

1981-01-01

Two terms, two job categories, 'technical writer' and 'technical author' are discussed in terms of industrial and business requirements and standards. A distinction between 'technical writing' and technical 'writing' is made. The term 'technical editor' is also considered. Problems inherent in the design of programs to prepare and train students for these jobs are discussed. A closer alliance between industry and academia is suggested as a means of preparing students with competent technical communication skills (especially writing and editing skills) and good technical skills.

Inertial fusion research: Annual technical report, 1985

International Nuclear Information System (INIS)

Larsen, J.T.; Terry, N.C.

1986-03-01

This report describes the inertial confinement fusion (ICF) research activities undertaken at KMS Fusion (KMSF) during 1985. It is organized into three main technical sections; the first covers fusion experiments and theoretical physics, the second is devoted to progress in materials development and target fabrication, and the third describes laser technology research. These three individual sections have been cataloged separately

Yucca Mountain Project technical status report (TSR), October 1989--March 1990

International Nuclear Information System (INIS)

1990-01-01

This Yucca Mountain Project Technical Status Report (TSR) on site characterization is the second in a series of reports that will be issued at approximately six-month intervals during site characterization. In addition, progress made toward the initiation and conduct of new site characterization activities is included. For this report, information on the technical progress made by Yucca Mountain Project participating organizations has been compiled covering the period from October 1989, through March 31, 1990. The status report consists of three sections: an introductory section; a section on the status of site characterization, which includes preparatory activities, sites programs, repository design, seals system design, waste package design, and performance assessment; and a reference section, which provides a complete listing of all published documents cited in the text. 59 refs

A Portfolio Analysis Tool for Measuring NASAs Aeronautics Research Progress toward Planned Strategic Outcomes

Science.gov (United States)

Tahmasebi, Farhad; Pearce, Robert

2016-01-01

Description of a tool for portfolio analysis of NASA's Aeronautics research progress toward planned community strategic Outcomes is presented. The strategic planning process for determining the community Outcomes is also briefly described. Stakeholder buy-in, partnership performance, progress of supporting Technical Challenges, and enablement forecast are used as the criteria for evaluating progress toward Outcomes. A few illustrative examples are also presented.

Technical evaluation of the electrical, instrumentation, and control design aspects of the low temperature overpressure protection system for the Salem nuclear power plant, Unit 1

International Nuclear Information System (INIS)

Laudenbach, D.H.

1979-03-01

The technical evaluation is presented for the electrical, instrumentation, and control design aspects of the low temperature overpressure protection system for the Salem nuclear power plant, Unit 1. Design basis criteria used to evaluate the acceptability of the system include operator action, system testability, single failure criterion, and seismic Category I and IEEE Std-279-1971 criteria

High-temperature gas-cooled reactor safety studies. Progress report for January 1, 1974--June 30, 1975

International Nuclear Information System (INIS)

Cole, T.E.; Sanders, J.P.; Kasten, P.R.

1977-07-01

Progress is reported in the following areas: systems and safety analysis; fission product technology; primary coolant technology; seismic and vibration technology; confinement components; primary system materials technology; safety instrumentation; loss of flow accident analysis using HEATUP code; use of coupled-conduction-convection model for core thermal analysis; development of multichannel conduction-convection program HEXEREI; cooling system performance after shutdown; core auxiliary cooling system performance; development of FLODIS code; air ingress into primary systems following DBDA; performance of PCRV thermal barrier cover plates; temperature limits for fuel particle coating failure; tritium distribution and release in HTGR; energy release to PCRV during DBDA; and mathematical models for HTGR reactor safety studies

Gas-Cooled Thermal Reactor Program. Semiannual technical progress report, October 1, 1982-March 3, 1983

International Nuclear Information System (INIS)

1983-06-01

This report provides descriptions and results of the technical effort during the first half of FY 83 on the Gas-Cooled Thermal Reactor Program. The work on Integration and Management (WBS 01) includes the preparation of the Advanced Systems Concept Evaluation Plan and the Advanced Systems Technology Development Plan in addition to the program management activities. The Market Definition (WBS 03) efforts considered the application of the Modular Reactor System with reforming (MRS-R) to the production of methanol and ammonia and the refining of petroleum. Within the Plant Technology (WBS 13) task there were activities to develop anlytical methods for investigation of Coolant Transport Behavior and to define methods and criteria for High Temperature Structural Engineering design. In addition to the work on the advanced HTGR for process heat users, new activities were initiated in support of the HTGR-SC/C Lead plant Protect (WBS 30 and 31). The Plant Simulation task (WBS 31) was initiated to develop a computer code for simulation of plant operation and for plant transient systems analysis. The efforts on the advanced HTGR systems was performed under the Modular Systems task (WBS 41) to study the potential for multiple small reactors to provide lower costs, improved safety, and higher availability than the large monolithic core reactors

Progress of the radioactive waste management at the Dalat Nuclear Research Institute and the role of an IAEA technical co-operation project in this process

International Nuclear Information System (INIS)

Nang, N.T.; Ngoc, O.V.; Nhu Thuy, T.T.; Nghi, D.V.; Thu, N.T.

2002-01-01

At present, the main radioactive waste generator in Vietnam is the Dalat Nuclear Research Institute (DNRI). For safe management of radioactive waste generated from this nuclear center, in 1982 Soviet specialists newly constructed one combined technology system for low level radioactive waste management. The existing system consists of two main parts, a Liquid Radioactive Waste Treatment Station and a Storage/Disposal Facility. The liquid treatment station can in principle meet the needs for this nuclear center but disposal technology and storage/disposal facilities are not good enough both with respect to safety and economy, especially the storage/disposal facility placed in Dalat, the tourist city. In order to help DNRI and Vietnam to solve the radioactive waste management problem, the IAEA Technical Co-operation (TC) project VIE/9/007 was implemented in Vietnam. The facilities and IAEA experts provided under this project gradually help to develop radioactive waste management at DNRI, Vietnam. This paper outlines progress under way in the management of the radioactive waste at the Nuclear Research Institute (NRI), Dalat, Vietnam, and the role of the IAEA Technical Co-operation (TC) project in this process. (author)

Analytical Chemistry Division annual progress report for period ending December 31, 1979

International Nuclear Information System (INIS)

Shults, W.D.; Lyon, W.S.

1980-05-01

The progress is reported in the following sections: analytical methodology, mass and emission spectrometry, technical support, bio-organic analysis, nuclear and radiochemical analysis, and quality assurance

Progress Report. Teilinstitut Nukleare Festkoerperphysik

International Nuclear Information System (INIS)

Kaefer, K.

1978-10-01

This Progress Report of the Teilinstitut Nukleare Festkoerperphysik covers the work done at the Institute during the period from June 1, 1977 to May 31, 1978. The main research areas presently under investigation are underlined by the arrangement of the report: structure and dynamics of solids, electronic structure and magnetism of solids, and the development and investigation of novel materials. Some technical developments important in carrying out this research are included as well. (orig.) [de

Assessing Progress in Mastery of Counseling Communication Skills

NARCIS (Netherlands)

A.J. Kuntze (Jeroen)

2009-01-01

textabstractDuring the last century the attention paid in higher education to the development of professional skills has progressively increased. In the first half of the last century the term ‘skill’ mainly referred to motor or technical actions, for instance driving a car or operating a machine

Comment on “Recent progress in thermodynamics of radiation——exergy of radiation,effective temperature of photon and entropy constant of photon”

Institute of Scientific and Technical Information of China (English)

无

2009-01-01

Chen et al.proposed the concepts of effective temperature of photon and entropy constant of photon in a recent paper [Chen Z S,Mo S P,Hu P.Recent progress in thermodynamics of radiation―exergy of radiation,effective temperature of photon and entropy constant of photon.Sci China Ser E-Tech Sci,2008,51(8):1096―1109] by enduing a single photon with macroscale thermodynamic parameters such as exergy and entropy.This paper argues that applying these concepts and their inferences to macro-scale thermodynamic system will lead to the results which conflict with macroscale thermodynamic laws.This means that the concepts of effective temperature of photon and entropy constant of photon are not correct.

Consolidated fuel reprocessing program. Progress report, July 1-September 30, 1981

International Nuclear Information System (INIS)

1981-12-01

Technical progress is reported in overview fashion in the following areas: process development, laboratory R and D, engineering research, engineering systems, integrated equipment test facility (IET) operations, and HTGR fuel reprocessing

Technical and economic feasibility of membrane technology. Fourth technical progress report, June 17-September 16, 1980

Energy Technology Data Exchange (ETDEWEB)

Sandre, A.

1980-10-01

Progress is reported on the investigation of the potential application of reverse osmosis, ultrafiltration and electrodialysis to the system of solids concentration in beet sugar process streams. During this period, emphasis was put on running reverse osmosis tests with a new prototype machine to select the most suitable membranes for the concentrating of sugar solutions. An economic analysis of using reverse osmosis in a factory producing 10/sup 6/ gal/day of thin juice is discussed. (DMC)

Analytical Chemistry Division annual progress report for period ending December 31, 1979

Energy Technology Data Exchange (ETDEWEB)

Shults, W.D.; Lyon, W.S. (ed.)

1980-05-01

The progress is reported in the following sections: analytical methodology, mass and emission spectrometry, technical support, bio-organic analysis, nuclear and radiochemical analysis, and quality assurance. (DLC)

Oregon Low-Temperature-Resource Assessment Program. Final technical report

Energy Technology Data Exchange (ETDEWEB)

Priest, G.R.; Black, G.L.; Woller, N.M.

1981-01-01

Numerous low-temperature hydrothermal systems are available for exploitation throughout the Cascades and eastern Oregon. All of these areas have heat flow significantly higher than crustal averages and many thermal aquifers. In northeastern Oregon, low temperature geothermal resources are controlled by regional stratigraphic aquifers of the Columbia River Basalt Group at shallow depths and possibly by faults at greater depths. In southeastern Oregon most hydrothermal systems are of higher temperature than those of northeastern Oregon and are controlled by high-angle fault zones and layered volcanic aquifers. The Cascades have very high heat flow but few large population centers. Direct use potential in the Cascades is therefore limited, except possibly in the cities of Oakridge and Ashland, where load may be great enough to stimulate development. Absence of large population centers also inhibits initial low temperature geothermal development in eastern Oregon. It may be that uses for the abundant low temperature geothermal resources of the state will have to be found which do not require large nearby population centers. One promising use is generation of electricity from freon-based biphase electrical generators. These generators will be installed on wells at Vale and Lakeview in the summer of 1982 to evaluate their potential use on geothermal waters with temperatures as low as 80/sup 0/C (176/sup 0/F).

HYFIRE: a tokamak/high-temperature electrolysis system

International Nuclear Information System (INIS)

Fillo, J.A.; Powell, J.P.; Benenati, R.; Varljen, T.C.; Chi, J.W.H.; Karbowski, J.S.

1981-01-01

The HYFIRE studies to date have investigated a number of technical approaches for using the thermal energy produced in a high-temperature Tokamak blanket to provide the electrical and thermal energy required to drive a high-temperature (> 1000 0 C) water electrolysis process. Current emphasis is on two design points, one consistent with electrolyzer peak inlet temperatures of 1400 0 C, which is an extrapolation of present experience, and one consistent with a peak electrolyzer temperature of 1100 0 C. This latter condition is based on current laboratory experience with high-temperature solid electrolyte fuel cells. Our major conclusion to date is that the technical integration of fusion and high-temperature electrolysis appears to be feasible and that overall hydrogen production efficiencies of 50 to 55% seem possible

Analyses, algorithms, and computations for models of high-temperature superconductivity. Final technical report

International Nuclear Information System (INIS)

Gunzburger, M.D.; Peterson, J.S.

1998-01-01

Under the sponsorship of the Department of Energy, the authors have achieved significant progress in the modeling, analysis, and computation of superconducting phenomena. Their work has focused on mezoscale models as typified by the celebrated ginzburg-Landau equations; these models are intermediate between the microscopic models (that can be used to understand the basic structure of superconductors and of the atomic and sub-atomic behavior of these materials) and the macroscale, or homogenized, models (that can be of use for the design of devices). The models the authors have considered include a time dependent Ginzburg-Landau model, a variable thickness thin film model, models for high values of the Ginzburg-Landau parameter, models that account for normal inclusions and fluctuations and Josephson effects, and the anisotropic Ginzburg-Landau and Lawrence-Doniach models for layered superconductors, including those with high critical temperatures. In each case, they have developed or refined the models, derived rigorous mathematical results that enhance the state of understanding of the models and their solutions, and developed, analyzed, and implemented finite element algorithms for the approximate solution of the model equations

JET Joint Undertaking. Progress report 1991 - volume 1

International Nuclear Information System (INIS)

1992-04-01

The ninth JET Progress Report provides an overview summary and puts into context the scientific and technical advances made on JET during 1991. The report contains a brief summary of the background to the project, and describes the basic objectives of JET and the principal design aspects of the machine

Progress report of Technical Physics Division: April 1980 - March 1982

International Nuclear Information System (INIS)

Chaudhry, Ramesh; Vijendran, P.

1983-01-01

Activities, with an individual summary of each, of the Technical Physics Division (TPD) of the Bhabha Atomic Research Centre (BARC), Bombay are reported for the period April 1980 - March 1982. The major thrust of the TPD's work has been in: (i) design and fabrication of instruments, devices and equipment and (ii) development of techniques in the frontline research and technology areas like vacuum science, surface analysis, cryogenics and crystal growing. The Division also provided custombuilt electronics equipment, vacuum systems and glass components and devices to the various Divisions of BARC and other units of the DAE. Training and manpower development activities and technology transfer activities are also reported. Lists of seminars, colloquia, publications during the period of the report are given. (M.G.B.)

Technical minutes of the ninth INDC meeting. Vienna, 16-20 May 1977

International Nuclear Information System (INIS)

Motz, H.

1978-05-01

Progress reports from data centres on data measurements, facilities and evaluations, on coordinating activities are presented along with reports of technical, ad-hoc and policy subcommittees, on plans for cooperation and past meetings

University of Florida, University research program in robotics. Annual technical progress report

International Nuclear Information System (INIS)

Crane, C.D. III; Tulenko, J.S.

1994-05-01

Progress is reported in the areas of environmental hardening, database, world modeling, vision, man-machine interface, advanced liquid metal reactor inspection robot, and articulated transporter/manipulator system (ATMS) development

University of Florida, University research program in robotics. Annual technical progress report

Energy Technology Data Exchange (ETDEWEB)

Crane, C.D. III; Tulenko, J.S.

1994-05-01

Progress is reported in the areas of environmental hardening, database, world modeling, vision, man-machine interface, advanced liquid metal reactor inspection robot, and articulated transporter/manipulator system (ATMS) development.

Influence of admission marks on the academic performance of technical architecture students

OpenAIRE

Gaspar Fàbregas, Kàtia; Núñez Andrés, María Amparo; Rodríguez Jordana, Juan; Jordana Riba, Francisco de Paula

2016-01-01

Traditionally, students from higher training cycle and upper secondary school education access higher technical education with a wide range of access marks in each group. The purpose of this article is to analyse how students’ backgrounds and access marks really influence their success in the first academic year and further evolution to obtain the degree of Technical Architecture. To achieve this aim, the progress of students from different backgrounds was analysed for three acade...

Progress Report for Period Ending December 1961. Department of Reactor Physics

Energy Technology Data Exchange (ETDEWEB)

Tell, B [ed.

1962-08-15

This is the second Progress Report from the Department for Reactor Physics of Aktiebolaget Atomenergi, which is issued for the information of institutions and persons interested in the progress of the work. In this report the activities of the General Physics Section have been included, since this section nowadays belongs to the department. This is merely an informal progress report, and the results and data presented must be taken as preliminary. Final results will be submitted for publication either in the regular technical journals or as monographs in the series AE-reports.

I-NERI QUARTERLY TECHNICAL PROGRESS REPORT - JANUARY 1 - MARCH 31, 2005

International Nuclear Information System (INIS)

Chang Oh

2005-01-01

The objective of this Korean/United States/laboratory/university collaboration is to develop new advanced computational methods for safety analysis codes for very-high-temperature gas-cooled reactors (VHTGRs) and numerical and experimental validation of these computer codes. The research will improve two well-respected light water reactor transient response codes (RELAP5/ATHENA and MELCOR) in the modeling of molecular diffusion and chemical equilibrium, and to validate these codes against the VHTGR accident data, i.e., air ingress and others from the literature. The VHTGR is intrinsically safe, has a proliferation-resistant fuel cycle, and many advantages relative to light water reactors (LWRs). This study consists of five tasks for FY-03: (1) development of computational methods for the VHTGR, (2) theoretical modification of aforementioned computer codes for molecular diffusion (RELAP5/ATHENA) and modeling CO and CO 2 equilibrium (MELCOR), (3) development of a state-of-the-art methodology for VHTGR neutronic analysis and calculation of accurate power distributions and decay heat deposition rates, (4) reactor cavity cooling system experiment, and (5) graphite oxidation experiment. First quarter of Year 3: (A) Prof. NO and Kim continued Task 1. We first performed the chemical reaction test for the VELUNA pebble oxidation experiment and then the analysis of the air ingress accident for PBMR 268MWt. In the GAMMA analysis, significant rise in pebble temperature was observed at the bottom of the core due to graphite oxidation. Since the air ingress process depends on the vault conditions, further analysis coupled with more detailed vault or containment modeling would be necessary as a future study. (B) Prof. Park continued Task 2. The experiments for SNU-RCCS were continued to provide the experimental data for the validation of the thermal hydraulic code being developed at KAIST and to evaluate the performance of the system using the experiments and system analysis

Crystalline Repository Project. Technical progress report, October 1982-March 1983

International Nuclear Information System (INIS)

1985-01-01

This document reports the progress being made periodically on the development of a geologic repository in crystalline rock for the permanent disposal of high-level nuclear waste. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Crystalline Respository Development (OCRD), a prime contractor of the US Department of Energy Repository Project Office. The studies include work by other prime contractors and by subcontractors to OCRD

Towards a space-borne quantum gravity gradiometer: progress in laboratory demonstration

Science.gov (United States)

Yu, Nan; Kohel, James M.; Kellogg, James R.; Maleki, Lute

2005-01-01

This paper describes the working principles and technical benefits of atom-wave interferometer-based inertial sensors, and gives a progress report on the development of a quantum gravity gradiometer for space applications at JPL.

Association Euratom - Risø National Laboratory, Technical University of Denmark - Annual Progress Report 2007

DEFF Research Database (Denmark)

Michelsen, Poul; Korsholm, Søren Bang; Juul Rasmussen, Jens

The programme of the Research Unit of the Fusion Association Euratom - Risø National Laboratory, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the pla......The programme of the Research Unit of the Fusion Association Euratom - Risø National Laboratory, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction...... phased out during 2007. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2007....

Particle beam fusion progress report, January-June 1980

International Nuclear Information System (INIS)

1981-05-01

An overview and technical summaries are given for research progress in each of the following general areas: (1) fusion target studies; (2) target experiments; (3) particle beam source theory; (4) diagnostics development; (5) particle beam experiments; (6) pulsed power research and development; (7) pulse power application; and (8) Electron Beam Fusion Accelerator project

Theoretical particle physics. Technical progress report, May 1, 1985-April 30, 1986

International Nuclear Information System (INIS)

Gottlieb, S.A.; Hendry, A.W.; Kostelecky, V.A.; Lichtenberg, D.B.

1986-05-01

Research activities during this past year included theoretical work in lattice gauge theory, EMC effect, supersymmetry and supergravity, weak interactions including CP violation, and superstrings. Progress in all these areas is reported

NAEP 1999 Long-Term Trend Technical Analysis Report: Three Decades of Student Performance. NCES 2005-484

Science.gov (United States)

Allen, Nancy L.; McClellan, Catherine A.; Stoeckel, Joan J.

2005-01-01

This report provides an update to the technical analysis procedures documenting the 1996 National Assessment of Educational Progress (NAEP) as presented in "The NAEP 1996 Technical Report" (Allen, Carlson, and Zelenak, 1999). It describes how the 1999 long-term trend data were incorporated into the trend analyses. Since no national main…

New high temperature plasmas and sample introduction systems for analytical atomic emission and mass spectrometry

International Nuclear Information System (INIS)

Montaser, A.

1993-01-01

In this research, new high-temperature plasmas and new sample introduction systems are explored for rapid elemental and isotopic analysis of gases, solutions, and solids using mass spectrometry and atomic emission spectrometry. During the period January 1993--December 1993, emphasis was placed on (a) analytical investigations of atmospheric-pressure helium inductively coupled plasma (He ICP) that are suitable for atomization, excitation, and ionization of elements possessing high excitation and ionization energies; (b) simulation and computer modeling of plasma sources to predict their structure and fundamental and analytical properties without incurring the enormous cost of experimental studies; (c) spectrosopic imaging and diagnostic studies of high-temperature plasmas; (d) fundamental studies of He ICP discharges and argon-nitrogen plasma by high-resolution Fourier transform spectrometry; and (e) fundamental and analytical investigation of new, low-cost devices as sample introduction systems for atomic spectrometry and examination of new diagnostic techniques for probing aerosols. Only the most important achievements are included in this report to illustrate progress and obstacles. Detailed descriptions of the authors' investigations are outlined in the reprints and preprints that accompany this report. The technical progress expected next year is briefly described at the end of this report

Assuring PSA technical adequacy for new advanced light water reactor designs

International Nuclear Information System (INIS)

Lutz, R.J.; Detar, H.L.; Schneider, R.E.

2012-01-01

The Probabilistic Safety Assessment (PSA) for an Advanced Light Water Reactor (ALWR) must exhibit a high level of technical adequacy, or technical quality, in order to be used as a reliable tool for making risk informed decisions concerning design and eventual operation of the plant. During the design phase, decisions on some design features may use the PSA as an input. Also, the PSA may be used as input to other operational decisions during plant design and construction including the development of procedures, development of technical specification limiting conditions for operation and scheduling of preventive maintenance activities. For the existing fleet of light water reactors (LWRs), PSA technical adequacy can be judged from wide ranging acceptance criteria such as the PRA (Probabilistic Risk Assessment) Standard in the United States of America that was developed jointly by the American Society of Mechanical Engineers (ASME) and the American Nuclear Society (ANS). However, the requirements for PRA technical adequacy in this PRA Standard assumes that the plant is built and has operation experience. Some of the requirements cannot be met for ALWRs in the design or construction phase and with no operational history. Key elements of a high level of technical adequacy include procedures, operator interviews, plant walk-downs and equipment reliability histories. The ability to include these key elements into the ALWR PSA to improve technical adequacy will progress as the ALWR progresses from the design stage through the construction stage and finally to the fuel load / pre-operational stage. As the technical adequacy becomes more robust, more confidence can be placed on risk-informed decisions that are made with the PSA. To assist in using the PSA as input to design and operational decisions in the design and construction stages of an ALWR, an addition to the ASME/ANS PRA Standard is being developed. The intent of this addition to the Standard is to provide

Pillars of peace: The evolution of nuclear technical cooperation

International Nuclear Information System (INIS)

Cetto, A.M.

2003-01-01

The twentieth century witnessed unprecedented scientific and technological progress, unfortunately paralleled by the development of weapons of mass destruction. And with this progress came an incredible amount of responsibility for scientists and governments. The creation of the IAEA and its technical cooperation programme brought together scientists and governments to use nuclear technology for the 'peaceful pursuits of mankind'. The programme supports application of nuclear techniques to solve socio-economic and human development problems in areas as diverse as agriculture, health, natural resource management, and radiation protection. Fifty years after President Eisenhower's famous 'Atoms for Peace' speech, the IAEA technical cooperation programme provides more than $70 million worth of experts, training, and procurement services each year to approximately 75% of its 137 Member States. But as development budgets shrink, the programme is seeking to make more meaningful use of resources at hand (national capacities, regional resources, development partners and the voluntary Technical Cooperation Fund), targeting specific problems of Member States and partnering with other sustainable development organizations. At the same time, efforts continue to overcome the past legacy that necessitated the 'Atoms for Peace' proposal in the first place. Even as development challenges are addressed, the IAEA, its partners and governments face other challenges along the way, including public opinion for a technology that had a devastating global introduction

Dual curvature acoustically damped concentrating collector. Semiannual technical progress report, June 1-December 1, 1978

Energy Technology Data Exchange (ETDEWEB)

None

1978-12-01

The project's first objective is to establish, analytically, the cost and performance of design choices within the boundaries of the basic proposed concept. With these cost and performance measures as a guide, the second project objective is to design a cost-effective Dual Curvature collector module and collector field array. The third objective is to establish technical and economic concept feasibility through prototype fabrication and test. The final objective is to define the Dual Curvature collector commercialization requirements. The Dual Curvature collector uses a unique reflector module consisting of a reflective film that is tensioned on a reflector support frame. The tensioned membrane (film) surface approximates a hyperbolic paraboloid that is capable of linear focusing when the surface tracks the sun's apparent motion in one axis. The reflective film can be backed by polystyrene foam with an air space between the film and the foam surfaces. This provides damping of the reflector surface to minimize the effect of wind gusts and physical impacts. The baseline collector is intended to operate at a concentration of ten (10) or greater with a nominal absorber temperature of 150/sup 0/C (300/sup 0/F). The Component Research and Analysis tasks which lead to the selection of a baseline collector configuration are discussed. Also, some preliminary results of the Collector Module Design task are presented.

Technical diagnostics of steam turbines

International Nuclear Information System (INIS)

Vlckova, B.; Drahy, J.

1987-01-01

This paper deals with practical experience in application of technical diagnostics methods to steam turbines, in particular using pedestal and shaft vibration measurements as well as estimation of bearing metal temperature and ultrasound emission signals. An estimation of effectiveness of the diagnostics methods used is given on the basis of experimental investigations made on a 30-MW turbine. (author)

Thermoregulation and temperature relations of alligators and other large ectotherms inhabiting thermally stressed habitats. Annual progress report, 1 July 1976--30 September 1977

International Nuclear Information System (INIS)

Spotila, J.R.

1977-06-01

Progress is reported on studies of the biophysical and thermal relationships between large ectotherms and their aquatic environment. Data are reported from laboratory and field studies on alligators, turtles, and fish. Mathematical models of the effect of body size and physical characteristics on temperature regulation of ectotherms and of thermal stress in aquatic organisms were developed. Results are included of field studies on the physiological and behavioral adjustments of turtles in response to changes in water temperature produced by thermal effluents in PAR Pond at the Savannah River Ecology Laboratory

[Shippingport Station Decommissioning Project]: FY 1987 annual progress report, October 1, 1986-September 30, 1987

International Nuclear Information System (INIS)

1988-01-01

This report presents progress on the Shippingport Station Decommissioning Project for FY 1987. There are two main topics: Project Management and Decommissioning Project Activities. Changes from technical and managerial concepts developed in the original Decommissioning Plan are presented with the related technical, economic, or schedule considerations. 3 refs., 9 figs., 4 tabs

Shippingport Station Decommissioning Project: FY 1988 annual progress report, October 1, 1987--September 30, 1988

International Nuclear Information System (INIS)

1989-01-01

This report presents progress on the Shippingport Station Decommissioning Project for FY 1988. There are two main topics: Project Management and Decommissioning Project Activities. Changes from technical and managerial concepts developed in the original Decommissioning Plan are presented with the related technical, economic, or schedular considerations. 4 refs., 17 figs., 2 tabs

Velocity distribution of electrons in time-varying low-temperature plasmas: progress in theoretical procedures over the past 70 years

Science.gov (United States)

Makabe, Toshiaki

2018-03-01

A time-varying low-temperature plasma sustained by electrical powers with various kinds of fRequencies has played a key role in the historical development of new technologies, such as gas lasers, ozonizers, micro display panels, dry processing of materials, medical care, and so on, since World War II. Electrons in a time-modulated low-temperature plasma have a proper velocity spectrum, i.e. velocity distribution dependent on the microscopic quantum characteristics of the feed gas molecule and on the external field strength and the frequency. In order to solve and evaluate the time-varying velocity distribution, we have mostly two types of theoretical methods based on the classical and linear Boltzmann equations, namely, the expansion method using the orthogonal function and the procedure of non-expansional temporal evolution. Both methods have been developed discontinuously and progressively in synchronization with those technological developments. In this review, we will explore the historical development of the theoretical procedure to evaluate the electron velocity distribution in a time-varying low-temperature plasma over the past 70 years.

Hydrogen storage - are we making progress?

International Nuclear Information System (INIS)

Blair, L.; Milliken, J.; Satyapal, S.

2004-01-01

'Full text:' The efficient storage of hydrogen in compact, lightweight systems that allow greater than 300-mile range has been identified as one of the major technical challenges facing the practical commercialization of fuel cell power systems for light-duty vehicles. Following the hydrogen vision announced by President Bush in his 2003 State of the Union address, the U.S. Department of Energy issued a Grand Challenge, soliciting ideas from universities, national laboratories, and industry. DOE's National Hydrogen Storage Project, an aggressive and innovative research program focused on materials R and D, will be launched in Fiscal Year 2005. An intensive effort is also underway in the private sector, both in the U.S. and abroad, to meet the challenging on-board hydrogen storage requirements. A historical perspective of hydrogen storage research and development will be provided and the current DOE technical targets for hydrogen storage systems will be discussed. The state-of-the-art in hydrogen storage will be summarized and recent progress assessed. Finally future research directions and areas of technical emphasis will be described. (author)

ITER technology R and D progress report. Report by the Director. ITER technical advisory committee meeting, 25-27 June 2000, St. Petersburg

International Nuclear Information System (INIS)

2001-01-01

The overall philosophy for the ITER design has been to use established approaches through detailed analysis and to validate their application to ITER through technology R and D, including fabrication of full scale or scalable models of key components. All this R and D work has been done for ITER under collaboration among the Home Teams, with a total resource of about 660 KIUA. R and D issues for ITER-FEAT are almost the same as for the 1998 ITER design. Major developments and fabrication have been completed and tests have significantly progressed. The technical output from the R and D validates the technologies and confirms the manufacturing techniques and quality assurance incorporated in the ITER design, and supports the manufacturing cost estimates for important key cost drivers. The testing of models is continuing to demonstrate their performance margin and/or to optimize their operational use. Their realisation offers insights useful for a possible future collaborative construction activity. Valuable and relevant experience has already been gained in the management of industrial scale, cross-party ventures. The successful progress of these projects increases confidence in the possibility of jointly constructing ITER in an international project framework. The R and D present status is summarized in the following: details are given in Chapters 2 and 3. Significant efforts and resources have been devoted to the Seven Large R and D Projects which cover all the major key components of the basic machine of ITER and their maintenance tools

LMFBR safety program. Annual technical progress report. Government fiscal year, 1977

International Nuclear Information System (INIS)

1977-01-01

Information is presented concerning the development of the SOMIX-1 computer code for sodium drop burning analysis; experimental analysis of burning sodium drops; aerosol leakage from containment buildings; high-temperature-concentration aerosols; aerosol source term from vaporized fuel; properties of high-temperature fuel mixtures; and development of the COMRADEX computer code for analysis of radiological doses in the environment from LMFBR accidents

Fusion reactor materials semiannual progress report for period ending September 30, 1990

International Nuclear Information System (INIS)

1991-04-01

This is the ninth in series of semiannual technical progress reports on fusion reactor materials. This report combines research and development activities which were previously reported separately in the following technical progress reports: Alloy Development of Irradiation Performance; Damage Analysis and Fundamental Studies; and Special Purpose Materials. These activities are concerned principally with the effects of the neutronic and chemical environment on the properties and performance of reactor materials; together they form one element of the overall materials program being conducted in support of the Magnetic Fusion Energy Program of the US Department of Energy. The other major element of the program is concerned with the interactions between reactor materials and the plasma and is reported separately. The Fusion Reactor Materials Program is a national effort involving several national laboratories, universities, and industries. The purpose of this series of reports is to provide a working technical record for the use of the program participants, and to provide a means of communicating the efforts of materials scientists to the rest of the fusion community, both nationally and worldwide

Fusion reactor materials: Semiannual progress report for period ending September 30, 1987

International Nuclear Information System (INIS)

1988-03-01

This is the third in a series of semiannual technical progress reports on fusion reactor materials. This report combines research and development activities which were previously reported separately in the following technical progress reports: Alloy Development for Irradiation Performances; Damage Analysis and Fundamental Studies; Special Purpose Materials. These activities are concerned principally with the effects of the neutronic and chemical environment on the properties and performance of reactor materials; together they form one element of the overall materials program being conducted in support of the Magnetic Fusion Energy Program of the US Department of Energy. The other major element of the program is concerned with the interactions between reactor materials and the plasma and is reported separately. The Fusion Reactor Materials Program is a national effort involving several national laboratories, universities, and industries. The purpose of this series of reports is to provide a working technical record for the use of the program participants, and to provide a means of communicating the efforts of materials scientists to the rest of the fusion community, both nationally and worldwide

Aircraft Nuclear Propulsion Project Quarterly Progress Report for Period Ending December 31, 1956

Energy Technology Data Exchange (ETDEWEB)

NA, NA [ORNL

1957-03-12

This quarterly progress report of the Aircraft Nuclear Propulsion Project at ORNL records the technical progress of research on circulating-fuel reactors and other ANP research at the Laboratory. The report is divided into five major parts: 1) Aircraft Reactor Engineering, 2) Chemistry, and 3) Metallurgy, 4) Heat Transfer and Physical Properties, Radiation Damage, and Fuel Recovery and Reprocessing, and 5) Reactor Shielding.

Optical Fiber High Temperature Sensor Instrumentation for Energy Intensive Industries

Energy Technology Data Exchange (ETDEWEB)

Cooper, Kristie L.; Wang, Anbo; Pickrell, Gary R.

2006-11-14

This report summarizes technical progress during the program “Optical Fiber High Temperature Sensor Instrumentation for Energy Intensive Industries”, performed by the Center for Photonics Technology of the Bradley Department of Electrical and Computer Engineering at Virginia Tech. The objective of this program was to use technology recently invented at Virginia Tech to develop and demonstrate the application of self-calibrating optical fiber temperature and pressure sensors to several key energy-intensive industries where conventional, commercially available sensors exhibit greatly abbreviated lifetimes due primarily to environmental degradation. A number of significant technologies were developed under this program, including • a laser bonded silica high temperature fiber sensor with a high temperature capability up to 700°C and a frequency response up to 150 kHz, • the world’s smallest fiber Fabry-Perot high temperature pressure sensor (125 x 20 μm) with 700°C capability, • UV-induced intrinsic Fabry-Perot interferometric sensors for distributed measurement, • a single crystal sapphire fiber-based sensor with a temperature capability up to 1600°C. These technologies have been well demonstrated and laboratory tested. Our work plan included conducting major field tests of these technologies at EPRI, Corning, Pratt & Whitney, and Global Energy; field validation of the technology is critical to ensuring its usefulness to U.S. industries. Unfortunately, due to budget cuts, DOE was unable to follow through with its funding commitment to support Energy Efficiency Science Initiative projects and this final phase was eliminated.

Symbol manipulation by computer applied to plasma physics. Technical progress report 2

International Nuclear Information System (INIS)

Rosen, B.

1977-09-01

Progress has been made in automating the calculation of parametric processes analytically by computer. The computations are performed automatically to lowest order quickly and efficiently. Work has started on a method for solving the nonlinear differential equations describing interacting modes

Experimental studies of elementary particle interactions at high energies: Technical progress report

International Nuclear Information System (INIS)

1987-01-01

This paper discusses progress of experiments at CERN and Fermilab. At CERN, data accumulation and analysis is discussed for the UA-6 experiment, which involves proton-antiproton collisions. At Fermilab, the testing of a collider detector for the Tevatron is discussed

Materials studies for magnetic fusion energy applications at low temperatures. VIII. Technical reports

International Nuclear Information System (INIS)

Reed, R.P.

1985-05-01

This report contains results of a research progam to produce material property data that will facilitte design and development of cryogenic structures for the superconducting magnets of magnetic fusion energy power plants and prototypes. Research results for 1984 are summarized in an initial ''Highlights of Results'' section and reported in detail in the technical papers that form the main body of this report. The technical papers are presented under four headings reflecting the main program areas: Welding, Nonmetallics, Structural Alloys, and Technology Transfer. Objectives, approaches, and achievements are summarized in an introduction to each program area

Advanced thermally stable jet fuels: Technical progress report, October 1994--December 1994

Energy Technology Data Exchange (ETDEWEB)

Schobert, H.H.; Eser, S.; Song, C.; Hatcher, P.G.; Boehman, A.; Coleman, M.M.

1995-02-01

There are five tasks within this project on thermally stable coal-based jet fuels. Progress on each of the tasks is described. Task 1, Investigation of the quantitative degradation chemistry of fuels, has 5 subtasks which are described: Literature review on thermal stability of jet fuels; Pyrolytic and catalytic reactions of potential endothermic fuels: cis- and trans-decalin; Use of site specific {sup 13}C-labeling to examine the thermal stressing of 1-phenylhexane: A case study for the determination of reaction kinetics in complex fuel mixtures versus model compound studies; Estimation of critical temperatures of jet fuels; and Surface effects on deposit formation in a flow reactor system. Under Task 2, Investigation of incipient deposition, the subtask reported is Uncertainty analysis on growth and deposition of particles during heating of coal-derived aviation gas turbine fuels; under Task 3, Characterization of solid gums, sediments, and carbonaceous deposits, is subtask, Studies of surface chemistry of PX-21 activated carbon during thermal degradation of jet A-1 fuel and n-dodecane; under Task 4, Coal-based fuel stabilization studies, is subtask, Exploratory screening and development potential of jet fuel thermal stabilizers over 400 C; and under Task 5, Exploratory studies on the direct conversion of coal to high quality jet fuels, are 4 subtasks: Novel approaches to low-severity coal liquefaction and coal/resid co-processing using water and dispersed catalysts; Shape-selective naphthalene hydrogenation for production of thermally stable jet fuels; Design of a batch mode and a continuous mode three-phase reactor system for the liquefaction of coal and upgrading of coal liquids; and Exploratory studies on coal liquids upgrading using mesopores molecular sieve catalysts. 136 refs., 69 figs., 24 tabs.

Microwave plasma source for neutral-beam injection systems. Quarterly technical progress report

International Nuclear Information System (INIS)

1981-01-01

The overall program is described and the technical and programmatic reasons for the decision to pursue both the RFI and ECH sources into the current hydrogen test stage is discussed. We consider the general characteristics of plasma sources in the parameter regime of interest for neutral beam applications. The operatonal characteristics, advantages and potential problems of RFI and ECH sources are discussed. In these latter two sections we rely heavily on experience derived from developing RFI and ECH ion engine sources for NASA

Maryland University sectored isochronous cyclotron (MUSIC): Progress report No. 11

Energy Technology Data Exchange (ETDEWEB)

1966-10-10

Technical progress during the past quarter has contributed to increased confidence that MUSIC will exceed its desired performance characteristics in all respects. Design studies on the magnet indicate that a field has been obtained capable of accelerating protons above the 112 MeV design objective. Initial rf study and design work indicates no major technical problems, although there are many difficult engineering problems to be solved. Center studies are just being started. Building installation and interface problems are being dealt with effectively, and no significant problems are anticipated in this area.

Technical Safety Appraisal of the Rocky Flats Plant

Energy Technology Data Exchange (ETDEWEB)

Brown, Blake P.

1989-01-01

This report provides the results of a Technical Safety Appraisal (TSA) of the Rocky Flats Plant (RFP) conducted November 14 to 18 and November 28 to December 9, 1988. This appraisal covered the effectiveness and improvements in the RFP safety program across the site, evaluating progress to date against standards of accepted practice. The appraisal included coverage of the timeliness and effectiveness of actions taken in response to the recommendations/concerns in three previous Technical Safety Appraisals (TSAs) of RFP Bldg. 707 conducted in July 1986, Bldgs. 771/774 conducted in October/November 1986, and Bldgs. 776/777 conducted in January/February 1988. Results of this appraisal are given in Section IV for each of 14 technical safety areas at RFP. These results include a discussion, conclusions and any new safety concerns for each technical safety area. Appendix A contains a description of the system for categorizing concerns, and the concerns are tabulated in Appendix B. Appendix C reports on the evaluation of the contractor's actions and the current status of each of the 230 recommendations and concerns contained in the three previous TSA reports.

Technical efficiency and productivity of Chinese county hospitals: an exploratory study in Henan province, China

Science.gov (United States)

Cheng, Zhaohui; Tao, Hongbing; Cai, Miao; Lin, Haifeng; Lin, Xiaojun; Shu, Qin; Zhang, Ru-ning

2015-01-01

Objectives Chinese county hospitals have been excessively enlarging their scale during the healthcare reform since 2009. The purpose of this paper is to examine the technical efficiency and productivity of county hospitals during the reform process, and to determine whether, and how, efficiency is affected by various factors. Setting and participants 114 sample county hospitals were selected from Henan province, China, from 2010 to 2012. Outcome measures Data envelopment analysis was employed to estimate the technical and scale efficiency of sample hospitals. The Malmquist index was used to calculate productivity changes over time. Tobit regression was used to regress against 4 environmental factors and 5 institutional factors that affected the technical efficiency. Results (1) 112 (98.2%), 112 (98.2%) and 104 (91.2%) of the 114 sample hospitals ran inefficiently in 2010, 2011 and 2012, with average technical efficiency of 0.697, 0.748 and 0.790, respectively. (2) On average, during 2010–2012, productivity of sample county hospitals increased by 7.8%, which was produced by the progress in technical efficiency changes and technological changes of 0.9% and 6.8%, respectively. (3) Tobit regression analysis indicated that government subsidy, hospital size with above 618 beds and average length of stay assumed a negative sign with technical efficiency; bed occupancy rate, ratio of beds to nurses and ratio of nurses to physicians assumed a positive sign with technical efficiency. Conclusions There was considerable space for technical efficiency improvement in Henan county hospitals. During 2010–2012, sample hospitals experienced productivity progress; however, the adverse change in pure technical efficiency should be emphasised. Moreover, according to the Tobit results, policy interventions that strictly supervise hospital bed scale, shorten the average length of stay and coordinate the proportion among physicians, nurses and beds, would benefit hospital efficiency

Accelerator research studies. Technical progress report, July 1, 1985-June 30, 1986

International Nuclear Information System (INIS)

1986-01-01

Progress is reported in these areas: study of instabilities and emittance growth in periodic focusing systems for intense beams; study of collective ion acceleration by intense electron beams and pulse powered plasma focus; and study of microwave sources and parameter scaling for high-frequency linacs

Nuclear waste management. Semiannual progress report, October 1982-March 1983

International Nuclear Information System (INIS)

Chikalla, T.D.; Powell, J.A.

1983-06-01

This document is one of a series of technical progress reports designed to report radioactive waste management programs at the Pacific Northwest Laboratory. Accomplishments in the following programs are reported: waste stabilization; Materials Characterization Center; waste isolation; low-level waste management; remedial action; and supporting studies

Commercial LFCM vitrification technology. Quarterly progress report, October-December 1984

Energy Technology Data Exchange (ETDEWEB)

Burkholder, H.C.; Jarrett, J.H. (comps.)

1985-07-01

This report is the first in a series of quarterly reports compiled by the Nuclear Waste Treatment Program Office at Pacific Northwest Laboratory to document progress on commercial liquid-fed ceramic melter (LFCM) vitrification technology. Progress in the following technical subject areas during the first quarter of FY 1985 is discussed: pretreatment systems, melting process chemistry, glass development and characterization, feed preparation and transfer systems, melter systems, canister filling and handling systems, off-gas systems, process/product modeling and control, and supporting studies. 33 figs., 12 tabs.

Shippingport Station Decommissioning Project: FY 1986 annual progress report, October 1, 1985 through September 30, 1986

International Nuclear Information System (INIS)

1987-01-01

This report presents progress on the Shippingport Station Decommissioning Project for FY 1986. There are two main topics: Project Management and Decommissioning Project Activities. Changes from technical and managerial concepts developed in the original Decommissioning Plan are presented with the related technical, economic, or schedule considerations. 9 refs., 4 figs., 3 tabs

Core Capabilities and Technical Enhancement -- FY-98 Annual Report

Energy Technology Data Exchange (ETDEWEB)

Miller, David Lynn

1999-04-01

The Core Capability and Technical Enhancement (CC&TE) Program, a part of the Verification, Validation, and Engineering Assessment Program, was implemented to enhance and augment the technical capabilities of the Idaho National Engineering and Environmental Laboratory (INEEL). The purpose for strengthening the technical capabilities of the INEEL is to provide the technical base to serve effectively as the Environmental Management Laboratory for the Office of Environmental Management (EM). An analysis of EM's science and technology needs as well as the technology investments currently being made by EM across the complex was used to formulate a portfolio of research activities designed to address EM's needs without overlapping work being done elsewhere. An additional purpose is to enhance and maintain the technical capabilities and research infrastructure at the INEEL. This is a progress report for fiscal year 1998 for the five CC&TE research investment areas: (a) transport aspects of selective mass transport agents, (b) chemistry of environmental surfaces, (c) materials dynamics, (d) characterization science, and (e) computational simulation of mechanical and chemical systems. In addition to the five purely technical research areas, this report deals with the science and technology foundations element of the CC&TE from the standpoint of program management and complex-wide issues. This report also provides details of ongoing and future work in all six areas.

Core capabilities and technical enhancement, FY-98 annual report

Energy Technology Data Exchange (ETDEWEB)

Miller, D.L.

1999-04-01

The Core Capability and Technical Enhancement (CCTE) Program, a part of the Verification, Validation, and Engineering Assessment Program, was implemented to enhance and augment the technical capabilities of the Idaho National Engineering and Environmental Laboratory (INEEL). The purpose for strengthening the technical capabilities of the INEEL is to provide the technical base to serve effectively as the Environmental Management Laboratory for the Department of Energy's Office of Environmental Management (EM). An analysis of EM's science and technology needs as well as the technology investments currently being made by EM across the complex was used to formulate a portfolio of research activities designed to address EM's needs without overlapping work being done elsewhere. An additional purpose is to enhance and maintain the technical capabilities and research infrastructure at the INEEL. This is a progress report for fiscal year 1998 for the five CCTE research investment areas: (a) transport aspects of selective mass transport agents, (b) chemistry of environmental surfaces, (c) materials dynamics, (d) characterization science, and (e) computational simulation of mechanical and chemical systems. In addition to the five purely technical research areas, this report deals with the science and technology foundations element of the CCTE from the standpoint of program management and complex-wide issues. This report also provides details of ongoing and future work in all six areas.

Technical feasibility study on polycarbonate solar panels

NARCIS (Netherlands)

Hackmann, M.M.; Meuwissen, M.H.H.; Bots, T.L.; Buijs, J.A.H.M.; Broek, K.M.; Kinderman, R.; Tanck, O.B.F.; Schuurmans, F.M.

2004-01-01

This paper describes a technical feasibility study on the application of polycarbonate (PC) plates in a superstrate photovoltaic module design. The lamination process was performed in a conventional laminator apparatus using low temperature curing (100°C) ethylene-vinyl-acetate (EVA) as the potting

A Tool for Measuring NASA's Aeronautics Research Progress Toward Planned Strategic Community Outcomes

Science.gov (United States)

Tahmasebi, Farhad; Pearce, Robert

2016-01-01

Description of a tool for portfolio analysis of NASA's Aeronautics research progress toward planned community strategic Outcomes is presented. For efficiency and speed, the tool takes advantage of a function developed in Excels Visual Basic for Applications. The strategic planning process for determining the community Outcomes is also briefly discussed. Stakeholder buy-in, partnership performance, progress of supporting Technical Challenges, and enablement forecast are used as the criteria for evaluating progress toward Outcomes. A few illustrative examples of using the tool are also presented.

Modular high-temperature reactor launched (and wallchart)

International Nuclear Information System (INIS)

Steinwarz, W.

1987-01-01

In view of the need for a technically unsophisticated, safe and economic reactor system, the KWU group has integrated the experience gained from German light-water reactor engineering and from successful operation of the German AVR experimental high-temperature reactor into the development of the High-Temperature Reactor (HTR)-module. The main components are illustrated and explained and technical data for the HTR-module is given. Safety is also considered. This includes graphs of core heat-up temperature for pebble-bed HTR and a graph of the temperature load of the fuel elements. The operation, control and applications are considered. The latter includes use in combined heat and power generation and community heating. Feasibility studies have shown that the HTR-module is cheaper, comparatively, than coal-fired power stations. (U.K.)

Simultaneous high-temperature removal of alkali and particulates in a pressurized gasification system. Final technical progress report, April 1981-July 1983

Energy Technology Data Exchange (ETDEWEB)

Mulik, P.R.; Alvin, M.A.; Bachovchin, D.M.

1983-09-01

This program is directed at performing experimental and analytical investigations, deriving system designs, and estimating costs to ascertain the feasibility of using aluminosilicate-based getters for controlling alkali in pressurized gasification systems. Its overall objective is to develop a plan for evaluating a scaled-up version of the gettering process as a unit operation or as an integral part of a particulate removal device. This report describes work completed on the four technical program tasks: Thermodynamic projections; Getter Selection and Qualification; System Performance Projections; and Program Definition for Concept Scale-up during the 27-month contract performance period. Work completed on the thermodynamic projections includes a data base update, development of alkali phase diagrams, and system performance projections. Getter selection and qualification efforts involved over 70 kinetic studies in which a leading candidate getter - emathlite - was selected and characterized. System performance projections identified a packed-bed configuration containing relatively large getter pellets as the preferred contacting device for a full-scale unit. For emathlite, we concluded that full-scale unit bed heights of 2 m or less would be required if we assume annual replacement on the basis of bed saturation capacity. Concept scale-up work involved defining the hardware and test program requirements for further development of the emathlite packed-bed system. 56 references, 80 figures, 74 tables.

Development of the Internet Library for the Second Progress Report on R and D for the geological disposal of HLW in Japan

International Nuclear Information System (INIS)

Shiotsuki, Masao; Ishikawa, Hirohisa

2000-01-01

This paper describes an Internet Library, the goal of which is to improve the quality assurance of the technical content of the Second Progress Report on R and D into the geological disposal of HLW in Japan. The Internet Library is used to centralize information management for the Second Progress Report. It uses a database system which stores a large quantity of technical memoranda and numeric data which provide the technical basis for the report. Members of the public and specialists are allowed access the data held on the system and may communicate their opinions and expert reviews, through the Internet. (author)

Office of Waste Isolation progress report, January 1978

International Nuclear Information System (INIS)

Zerby, C.D.

1978-01-01

This document, prepared to report progress on the National Waste Terminal Storage (NWTS) program, consists of project reports on work performed by organizations under subcontract to OWI, by DOE contractors, by OWI consultants, and by other federal agencies participating in the NWTS program. The project reports are made under the headings technical projects, facility projects, planning and analysis, and regulatory affairs

Office of Waste Isolation progress report, December 1977

International Nuclear Information System (INIS)

Zerby, C.D.

1976-01-01

This document reports progress on the OWI's portion of the National Waste Terminal Storage (NWTS) program. It comprises project reports on work performed by organizations under subcontract to OWI, by DOE contractors, by OWI consultants, and by other federal agencies participating in the NWTS program. They are made under the headings technical projects, facility projects, planning and analysis, and regulatory affairs

Office of Waste Isolation progress report, January 1978

Energy Technology Data Exchange (ETDEWEB)

Zerby, C.D.

1978-02-28

This document, prepared to report progress on the National Waste Terminal Storage (NWTS) program, consists of project reports on work performed by organizations under subcontract to OWI, by DOE contractors, by OWI consultants, and by other federal agencies participating in the NWTS program. The project reports are made under the headings technical projects, facility projects, planning and analysis, and regulatory affairs. (DLC)

Progress report of the Teilinstitut Nukleare Festkoerperphysik

International Nuclear Information System (INIS)

Heger, G.

1976-09-01

This progress report of the Teilinstitut Nukleare Festkoerperphysik covers the period from 1st June 1975 - 31st May 1976. The arrangement has been chosen to emphasis the main areas of research in which the institute is presently involved. These areas are Dynamics of Solids and Liquids, Electronic Structure and Magnetism of Solids and Development of Materials. Some of the technical developments relevant to these topics are also included. (orig.) [de

Theoretical particle physics: Technical progress report, May 1, 1988--April 30, 1989

International Nuclear Information System (INIS)

Gottlieb, S.A.

1989-05-01

My research in lattice gauge theory during the past year is described. Several projects were completed dealing with QCD simulations including dynamical fermions. The phase diagram for QCD with four quark flavors was studied using a finite size scaling analysis at intermediate quark mass. With two light quark flavors, a study of the hadron spectrum was completed. These results, when combined with an earlier study of the finite temperature chiral symmetry restoration transition, determine the transition temperature in MeV. The transition temperature is seen to be ∼130 MeV, which makes it more accessible to observation at a relativistic heavy-ion collider than previously expected. Studies of hadronic screening lengths and the quark number susceptibility at zero chemical potential provide further probes of the high temperature phase of QCD. In the pure gluon theory, claims that the finite temperature deconfinement transition is second order, rather than first order, were investigated using a finite size scaling analysis. Finally, work was done to port computer code to new environments in order to pursue more ambitious calculations on more powerful hardware than the ST-100 used for the calculations reported here

Project Progress Assessment Report (PPAR) 2015

International Nuclear Information System (INIS)

Sall, Baba

2015-01-01

This evaluation reports reviews basic information, output achievement, equipment and human resources, comment and recommendations. It highlights outputs Fully achieved, those which are partially achieved or in progress and also non achieved outputs. Regarding comments and lessons learned, counterpart stated that the overall timeline of the project is respected, even if activities are delayed to adapt to technical, financial and human resources constraints. The results obtained are in line with expectations thanks to a rigorously respected scientific approach. The Collegial Coordination of the project (DSV-LNERV-CIRAD) and the TO are in phase on the conduct of the Project the collection of baseline data is a crucial phase in the implementation of tsetse control programs. It makes it possible to implement a good strategy. The scientific and technical rigor and the good atmosphere within the Project team are also to be retained.

Project Progress Assessment Report (PPAR) 2012

International Nuclear Information System (INIS)

Sall, Baba

2012-01-01

This evaluation reports reviews basic information, output achievement, equipment and human resources, comment and recommendations. It highlights outputs Fully achieved, those which are partially achieved or in progress and also non achieved outputs. Regarding comments and lessons learned, counterpart stated that the overall timeline of the project is respected, even if activities are delayed to adapt to technical, financial and human resources constraints. The results obtained are in line with expectations thanks to a rigorously respected scientific approach. The Collegial Coordination of the project (DSV-LNERV-CIRAD) and the TO are in phase on the conduct of the Project the collection of baseline data is a crucial phase in the implementation of tsetse control programs. It makes it possible to implement a good strategy. The scientific and technical rigor and the good atmosphere within the Project team are also to be retained.

International Standards Development for Marine and Hydrokinetic Renewable Energy - Final Report on Technical Status

Energy Technology Data Exchange (ETDEWEB)

Rondorf, Neil E.; Busch, Jason; Kimball, Richard

2011-10-29

This report summarizes the progress toward development of International Standards for Marine and Hydrokinetic Renewable Energy, as funded by the U.S. Department of Energy (DOE) under the International Electrotechnical Commission (IEC) Technical Committee 114. The project has three main objectives: 1. Provide funding to support participation of key U.S. industry technical experts in 6 (originally 4) international working groups and/or project teams (the primary standards-making committees) and to attend technical meetings to ensure greater U.S. involvement in the development of these standards. 2. Provide a report to DOE and industry stakeholders summarizing the IEC standards development process for marine and hydrokinetic renewable energy, new international standards and their justifications, and provide standards guidance to industry members. 3. Provide a semi-annual (web-based) newsletter to the marine renewable energy community. The newsletter will educate industry members and stakeholders about the processes, progress, and needs of the US efforts to support the international standards development effort. The newsletter is available at www.TC114.us

Accelerator research studies: Technical progress report, June 1, 1988--May 31, 1989

International Nuclear Information System (INIS)

1989-01-01

This report discusses research progress in the following general topics: Study of transport and longitudinal compression of intense, high-brightness beams; study of collective ion acceleration by intense electron beams and pulse powered plasma focus; and study of microwave sources and parameter scaling for high-frequency electron-positron supercollider linacs

Technical progress report, October 1, 1980-September 30, 1981

International Nuclear Information System (INIS)

1981-01-01

Progress during the 12-month period, October 1, 1980 to September 30, 1981 on the University of Wisconsin Plasma Physics contract is described. Most of the work centers around two major experimental devices, the Levitated Octupole and Tokapole II. A major upgrade of the Octupole is underway to include 2 MW of ICRH and 1.8 MW of neutral beam heating. Meanwhile, gun optimization and low field operation has resulted in the attainment of 35% beta, a factor of 9 above the single fluid ballooning limit. The ICRH experiment is well underway, and the first neutral beam source has been installed. The Tokapole is operating reliably at the full design field of 10 kG with 12 msec discharges. Low q (approx. 0.4) discharges with flat current profiles are obtained at reduced (approx. 3kG) toroidal field. The device is presently being used to study shear Alfven wave heating, ECRH startup, poloidal ohmic heating, and plasma transport

Development of high temperature turbine

Energy Technology Data Exchange (ETDEWEB)

Takahara, Kitao; Nouse, Hiroyuki; Yoshida, Toyoaki; Minoda, Mitsuhiro; Matsusue, Katsutoshi; Yanagi, Ryoji

1988-07-01

For the contribution to the development of FJR710, high by-pass ratio turbofan engine, with the study for many years of the development of high efficiency turbine for the jet engine, the first technical prize from the Energy Resource Research Committee was awarded in April, 1988. This report introduced its technical contents. In order to improve the thermal efficiency and enlarge the output, it is very effective to raise the gas temperature at the inlet of gas turbine. For its purpose, by cooling the nozzle and moving blades and having those blades operate at lower temperature than that of the working limitation, they realized, for the first time in Japan, the technique of cooling turbine to heighten the operational gas temperature. By that technique, it was enabled to raise the gas temperature at the inlet of turbine, to 1,350/sup 0/C from 850/sup 0/C. This report explain many important points of study covering the basic test, visualizing flow experiment, material discussion and structural design in the process of development. (9 figs)

Productivity Measurement Of Technical Institute

Directory of Open Access Journals (Sweden)

Miss.Pooja Yadav

2015-05-01

Full Text Available Abstract The increasing concern over globalization between other things has made the achievement of lifetime skills vital for all classes of people. Achievement of such skills can be developed from technical education programs in the advance of any nation. Skill gaining provides knowledge and inculcates the approaches that are essential for arrival and progress into an occupation. When skills are developed in any occupation it will provide and improve the standard of living with the cover beside poverty thereby behind national development. This paper observes sampling distribution and moving average concept that how technical education can generate the required skills the significance of skill acquisition its roles benefits and sustainability in national development. It also mentions among others that government should look into and improve productivity that can encourage skill achievement for the youths. The solutions are divided the sampling box into few group before stacking up workstation and use table and some other wood product. Cost reduction for each solution was intended and the solution with highest cost decrease is chosen to increase the productivity of the college.

Thermoregulation and temperature relations of alligators and other large ectotherms inhabiting thermally stressed habitats. Progress report, 1 October 1974--30 September 1977

International Nuclear Information System (INIS)

Spotila, J.R.

1977-06-01

Significant progress has been made in determining the mechanisms by which large ectotherms adjust to thermal stress in their natural environment. The effect of mouth gaping on head temperatures and the role of radiation, conduction and convection on body temperatures of alligators have been determined. The utility of energy budget modeling as a method for studying the thermoregulatory mechanisms of animals has been demonstrated. Steady state and time dependent models of body temperature have been tested. Convection coefficients and evaporative water loss rates have been measured for the turtle, Chysemys scripta. Climate space diagrams have been formulated and are being tested. Behavioral thermoregulation of turtles has been studied in PAR pond on the Savannah River Plant, Aiken, S.C. Steady state energy budget equations have been computed for largemouth bass. Experimental heat transfer coefficients indicate that most heat transfer is through the body wall and not via the gills. A time dependent model is being tested. It predicts the body temperature of a fish in a heterothermal environment. Theoretical calculations have been made of the effects of body size, color, and metabolism on the temperature regulation of ectotherms

CONFERENCE NOTE: Sixth Symposium on Temperature Scheduled for March 1982

Science.gov (United States)

1981-07-01

The call for papers for the 6th Symposium on Temperature, Its Measurement and Control in Science and Industry has been issued. The Symposium is scheduled to take place in Washington, DC, USA during the week of March 14 18, 1982. Like its predecessors held in the years 1919, 1939, 1954, 1961, and 1971, the 6th Symposium will stress advances in the measurement of thermodynamic values of temperature, in temperature reference points, in temperature sensors and instruments for the control of temperature, and in the development and use of temperature scales. For the first time, an exhibit of thermometry will be a part of the Symposium. Manuscripts to be submitted for inclusion in the Symposium should be sent to the 6th Temperature Symposium Program Chairman, National Bureau of Standards, by September 15, 1981. Those papers accepted for the Symposium will be due in camera-ready form by February 15, 1982. Original papers on all of the topics listed above, as well as reviews of the past decade's progress in thermometry and temperature control, are solicited by the Symposium organizers. The Symposium arrangements and registration are in the care of the Instrument Society of America (represented on the Symposium General Committee by Mr C T Glazer, 67 Alexander Drive, PO Box 12277, Research Triangle Park, North Carolina, 27709, USA). Questions regarding the instrument exhibits should also be addressed to the ISA. The technical program for the Symposium is the responsibility of a committee headed by Dr J F Schooley, Room B-128 Physics Building, National Bureau of Standards, Washington, DC, 20234, USA. The Symposium proceedings will be published by the American Institute of Physics.

Simultaneous multipoint measurements of density gradients and temperature in a flame. Progress report, July 1, 1982-January 31, 1983

International Nuclear Information System (INIS)

Chang, R.K.; Chu, B.T.; Long, M.B.

1983-02-01

An account is given of recent progress in the development of nonintrusive optical diagnostic techniques and the application of these techniques to turbulent combustion systems. The primary focus of the work over the past year has been in: (1) the use of a broadband rotational CARS technique for the measurement of temperature in flames, and (2) the use of spontaneous Raman scattering to simultaneously map out the fuel gas concentration in a turbulent diffusion flame at 2500 points in a plane intersecting the flow. A summary of new results in each of these areas is given

Technical Co-operation Report for 1996. Report by the Director General

International Nuclear Information System (INIS)

1997-01-01

The Agency's Technical Cooperation (TC) Programme made further progress during 1996 in implementing recent initiatives to strengthen efficiency and effectiveness. These initiatives seek to maximize the developmental contribution of counterpart institutions by emphasizing the management of technology to solve social and economic problems. The new direction has been embodied in the term ''Partners in Development''. The Partners in Development approach is reflected in last year's Report to the Board of Governors and the General Conference on Strengthening of the Agency's Technical Co-operation Activities, which provided an update on ongoing activities and elaborated new initiatives. The 1995 Technical Cooperation Report focused on the progress in implementing these initiatives. Next year, the Secretariat plans to combine the TC Report with the Report on Strengthening of the Agency's Technical Co-operation Activities in order to improve the clarity, consistency and economy of these presentations. Establishing a development partnership with Member States is the central goal of a new Strategy for TC. The refinement of this strategy required considerable effort during 1996, when the process first began to define objectives, targets and the means of accomplishing them. Alongside internal consultations, the role of SAGTAC became instrumental in reaching consensus on the main elements of the strategy. Future efforts include the formulation of implementation plans for the strategy. Once completed, the strategy will be presented to the TACC and Board in 1997. Reflecting these developments, section A of this Report presents the basic features of the TC Strategy, and the approach to be taken to achieve its objectives. The Strategy addresses among others the recommendations contained in resolution GC(40)/RES/13 on the Strengthening of Technical Co-operation: activities to improve the scientific and technological capabilities of developing countries; to achieve sustainable

The 1989 progress report: Polytechnic school laboratories' Direction

International Nuclear Information System (INIS)

1989-01-01

The 1989 progress report of the laboratories' Direction of the Polytechnic School (France) is presented. The research activities carried out in each laboratory are summarized. Scientific and technical cooperation, financial and employement aspects are included. The main fields of research are: biochemistry, chemistry, reaction mechanisms, organic synthesis, mechanics of solids, meteorology, irradiated solids, optics, physics, biophysics, lasers, mathematics, econometrics, epistemology, management and computer science [fr

Office of Waste Isolation progress report, December 1977

Energy Technology Data Exchange (ETDEWEB)

Zerby, C.D.

1976-01-31

This document reports progress on the OWI's portion of the National Waste Terminal Storage (NWTS) program. It comprises project reports on work performed by organizations under subcontract to OWI, by DOE contractors, by OWI consultants, and by other federal agencies participating in the NWTS program. They are made under the headings technical projects, facility projects, planning and analysis, and regulatory affairs. (DLC)

The impact of the endogenous technical change on climate policies

International Nuclear Information System (INIS)

Sassi, O.

2008-11-01

This research aims at revisiting the 'autonomous vs. induced' debate on the costs of climate policies, first by broadening the framework of the technical change induction to other economical sectors, and then by attempting to go beyond the concept of technical change induction and think in terms of a structural change induction. After a review of modes of representation of the technical progress in economical prospective models for the assessment of climate policies, the author presents the IMACLIM-R model, a recursive general equilibrium model which simulates the evolution of the world economy within 12 regions and 12 sectors between 2001 and 2100. The results obtained with this model are then presented and discussed, in the case of a reference scenario which displays a significant change towards a carbon-intensive path. These results stress the risks related to a 'laissez faire' attitude. The author explores the consequences in terms of climate policies with a more or less extended taking into account of phenomena of induction of technical and structural changes

TECHNICAL TRAINING SEMINAR

CERN Multimedia

Davide Vitè

2002-01-01

NEW DATE AND TIME!!! Wednesday 26 June from 11:00 to 12:00 - Training Centre Auditorium - bldg. 593-11 High Temperature Superconductors: Progress and Issues Prof. Jan Evetts / UNIVERSITY OF CAMBRIDGE, Department of Materials Science and Metallurgy, UK Grappling with grain boundaries: Current transport processes in granular High Temperature Superconductors (HTS) The development of High Temperature Superconductors, seen from a materials scientist's point of view, is relevant to the superconductivity community at CERN: their possible high current applications can include high performance magnets for future accelerators. There is an urgent need to develop a quantitative description of HTS conductors in terms of their complex anisotropy, inhomogeneity and dimensionality. This is essential both for the practical specification of a conductor and for charting routes to conductor optimisation. The critical current, the n-value, dissipation and quenching characteristics are amongst most important parameters that make u...

Technical progress, the concept of individualized cancer treatment and the innovation of computer-assisted radiotherapy planning

International Nuclear Information System (INIS)

Merkle, K.; Tanneberger, S.; Matschke, S.

1985-01-01

After a first step of cancerogenesis, the further development of the tumor is an individual process. At the end of this process the tumor is formed as an individual in the individual. The individuality of cancer exists on the level of organs, tissues and cells and includes an individual tumor-host relationship. Today, optimized cancer treatment requires a most precise biological characterization possible of the tumor and of the tumor-host relationship, which will provide objective information about the individual character of every tumor. Routine analysis and strict therapeutic consideration of the clinical and biological individuality of human cancer can offer real chances for the improvement of cancer treatment. A routine acquisition of individual tumor characteristics will be possible only if methods and equipment are available for the registration of suitable parameters. In this context technical innovations have an essential influence on the realization of the concept of individualized cancer treatment. With the method of flow cytophotometry and other techniques examples are given in how far the ideas of individual cancer management can be realized by introduction of new technical solutions into medical research and clinical practice. Unfortunately there is still a lack of methodology in individualizing cancer treatment. The individualization of radiotherapy is connected to an extremely high degree of technical innovations. Particularly this refers to the topometrical description of the target volume in relation to the adjacent anatomical structures and the body contour as well as the fitting of isodoses to the shape and size of the target volume. As an example of innovation of a technical solution for individual radiotherapy planning the computer-assisted radiotherapy planning system DOPSY is described. (author)

Technical evaluation of the electrical, instrumentation, and control design aspects of the low temperature overpressure protection system for the Haddam Neck Nuclear Power Plant

International Nuclear Information System (INIS)

Laudenbach, D.H.

1979-03-01

The technical evaluation of the electrical, instrumentation, and control design aspects of the low temperature overpressure protection system for the Haddam Neck Nuclear Power Plant is presented. Design basis criteria used to evaluate the acceptability of the system included operator action, system testability, single failure criterion, and seismic Category I and IEEE Std-279-1971 criteria. This report is supplied as part of the Selected Electrical, Instrumentation, and Control Systems Issues Support Program being conducted for the U.S. Nuclear Regulatory Commission by Lawrence Livermore Laboratory

Power system technical performance issues related to the application of long HVAC cables

DEFF Research Database (Denmark)

Wiechowski, on behalf of Cigre WG C4.502, W.; Sluis, L. V. der; Ohno, Teruo

2011-01-01

This paper reports the progress of work of Cigre Working Group C4.502 “Power system technical performance issues related to the application of long HVAC cables”. The primary goal of the WG C4.502 is to write a technical brochure that will serve as practical guide for performing studies necessary...... for assessing the technical performance of HV/EHV systems with large share of AC cable lines. This paper besides providing a background for formulation of WG C4.502 and its overall aim, describes the tasks that were accomplished before the interim report was submitted to Study Committee C4 System Technical...... Performance in August 2010. The work in the WG is ongoing and final report will be ready according to the time schedule in 2012. The focus of this paper is in particular to show all issues related to system technical performance with assigned weights in terms of their importance and/or uniqueness for cable...

A technical solution to a difficult problem - An update

International Nuclear Information System (INIS)

Asselstine, J.K.

1985-01-01

A goal of the Reduced Enrichment Research and Test Reactor Program (RERTR) established by the U.S. Department of Energy is to develop the technical means needed to utilize LEU instead of HEU fuels in research and test reactors and to do so without operational penalties and without affecting safety characteristics. This goal has been pursued now for seven years in cooperation with many of you who are participants in this conference. The program has made significant progress in the development, demonstration and application of new LEU research reactor fuels. According to recent projections, the percentage of HEU fuel in international commerce which is technically replaceable with LEU fuels has been growing steadily as research continues. There appears to be no technical barrier to eventual replacement of HEU fuel with LEU fuel in research and test reactors. While there are many politically complex and technically difficult issues involved in nonproliferation, I conclude that the use of highly enriched weapons grade uranium as a fuel in civilian research reactors stands out as one problem which has a straight forward technical solution. The technical solution is the effort you in the RERTR program are embarked on. Once that solution is in hand, the operators of research reactors are urged to take political and legal initiatives to make the conversion happen. By effecting this conversion they will help minimize the trade in highly enriched uranium and make the world a little safer

A technical solution to a difficult problem - An update

Energy Technology Data Exchange (ETDEWEB)

Asselstine, J K

1985-07-01

A goal of the Reduced Enrichment Research and Test Reactor Program (RERTR) established by the U.S. Department of Energy is to develop the technical means needed to utilize LEU instead of HEU fuels in research and test reactors and to do so without operational penalties and without affecting safety characteristics. This goal has been pursued now for seven years in cooperation with many of you who are participants in this conference. The program has made significant progress in the development, demonstration and application of new LEU research reactor fuels. According to recent projections, the percentage of HEU fuel in international commerce which is technically replaceable with LEU fuels has been growing steadily as research continues. There appears to be no technical barrier to eventual replacement of HEU fuel with LEU fuel in research and test reactors. While there are many politically complex and technically difficult issues involved in nonproliferation, I conclude that the use of highly enriched weapons grade uranium as a fuel in civilian research reactors stands out as one problem which has a straight forward technical solution. The technical solution is the effort you in the RERTR program are embarked on. Once that solution is in hand, the operators of research reactors are urged to take political and legal initiatives to make the conversion happen. By effecting this conversion they will help minimize the trade in highly enriched uranium and make the world a little safer.

E-Division semiannual report. Progress report, June 1--December 31, 1977

International Nuclear Information System (INIS)

Kelley, P.A.

1978-03-01

The status of the programs and projects of the Electronics Division is reported for the period of June through December 1977. The presentation is divided into three sections: Research, Engineering Support, and Technical Services. Each of these sections presents the activities and accomplishments of the corresponding branch within the Division. The primary goal of the Research and Development branch is to advance technology for future applications. The primary goal of the Engineering Support branch is to apply advanced technology to laboratory and material problems. The primary goal of the Technical Services branch is to provide a technical base and support for Laboratory programs. These goals are reflected in this report. Among the subject areas included are the following: radiation detectors, temperature monitoring, electromagnetic probing, Josephson junction switching devices, fiber optics, high-temperature electronics, HVAC systems, microprocessors, fuel cell-powered vehicles, laser fusion

Progress report No. 2 on the Scientific Investigation Program for the Nevada Yucca Mountain Site, October 1, 1989--March 31, 1990

International Nuclear Information System (INIS)

1990-01-01

In accordance with the requirements of Section 113(b)(3) of the Nuclear Waste Policy Act of 1982 (Pub. L. No. 97-425), as amended, the US Department of Energy (DOE) has prepared this report on the progress of scientific investigation activities at Yucca Mountain in southern Nevada for October 1, 1989, through March 31, 1990. This report is the second of a series of reports that are issued at intervals of approximately six months during the period of scientific investigation. The progress report presents short summaries of the status of scientific investigation activities and cites technical reports and research products that provide more detailed information on the activities. The report provides highlights of work started during the reporting period, work in progress, and work completed and documented during the reporting period. In addition, the report is the vehicle for discussing major changes, if any, to the DOE's scientific investigation program. The progress report conveys information in a convenient summary form to be used for informational purposes only. It is not intended to be the mechanism for controlling and documenting technical or policy positions regarding changes in schedules or the technical program. Such changes are controlled through rigorous DOE change-control procedures. The progress report only describes such approval changes. 49 refs., 3 tabs

Nuclear-waste management semiannual progress report, April 1982-September 1982

International Nuclear Information System (INIS)

Chikalla, T.D.; Powell, J.A.

1982-12-01

This document is one of a series of technical progress reports designed to report on radioactive waste management programs at Pacific Northwest Laboratory. Accomplishments in the following programs are reported: waste treatment; nuclear waste Materials Characterization Center (MCC); airborne waste management; low-level waste management; waste isolation; remedial actions; and supporting studies

High temperature metallic materials for gas-cooled reactors

International Nuclear Information System (INIS)

1989-06-01

The Specialists' Meeting was organized in conjunction with an earlier meeting on this topic held in Vienna, Austria, 1981, which provided for a comprehensive review of the status of materials development and testing at that time and for a description of test facilities. This meeting provided an opportunity (1) to review and discuss the progress made since 1981 in the development, testing and qualification of high temperature metallic materials, (2) to critically assess results achieved, and (3) to give directions for future research and development programmes. In particular, the meeting provided a form for a close interaction between component designers and materials specialists. The meeting was attended by 48 participants from France, People's Republic of China, Federal Republic of Germany, Japan, Poland, Switzerland, United Kingdom, USSR and USA presenting 22 papers. The technical part of the meeting was subdivided into four technical sessions: Components Design and Testing - Implications for Materials (4 papers); Microstructure and Environmental Compatibility (4 papers); Mechanical Properties (9 papers); New Alloys and Developments (6 papers). At the end of the meeting a round table discussion was organized in order to summarize the meeting and to make recommendations for future activities. This volume contains all papers presented at the meeting. A separate abstract was prepared for each of these papers. Refs, figs and tabs

Technical progress review of extraction of uranium from fly ash

International Nuclear Information System (INIS)

Gao Renxi; Gao Junning; Wu Qingming; Chen Gang; Wan Hongjin; Zhang Ziyue

2014-01-01

The increasing of fly ash in coal-fired power plants at home and abroad year by year and the potential impacts to the environment attracted media attention. Although the extraction of uranium from the fly ash in coal-fired power plants had optional process from technique aspect and sufficient preliminary researches, but considering the low grade of the uranium in fly ash and particularity of the mineral composition, it is easy to have a high cost of extraction. As a consequence, it is not included in the development plan of uranium mining and metallurgy. The present applications of fly ash are only building materials, building roads and pit valley backfill, the resource utilization rate was low and was still in its early stages of development and application. In view of this, the research advances and the latest development trends of extraction of uranium from fly ash at home and abroad were introduced from the technical aspect, and the beneficial analyzes of the prospect and advices to this industry were given. (authors)

High-Efficiency Nitride-Based Solid-State Lighting. Final Technical Progress Report

International Nuclear Information System (INIS)

Paul T. Fini; Shuji Nakamura

2005-01-01

In this final technical progress report we summarize research accomplished during Department of Energy contract DE-FC26-01NT41203, entitled ''High-Efficiency Nitride-Based Solid-State Lighting''. Two teams, from the University of California at Santa Barbara (Principle Investigator: Dr. Shuji Nakamura) and the Lighting Research Center at Rensselaer Polytechnic Institute (led by Dr. N. Narendran), pursued the goals of this contract from thin film growth, characterization, and packaging/luminaire design standpoints. The UCSB team initially pursued the development of blue gallium nitride (GaN)-based vertical-cavity surface-emitting lasers, as well as ultraviolet GaN-based light emitting diodes (LEDs). In Year 2, the emphasis shifted to resonant-cavity light emitting diodes, also known as micro-cavity LEDs when extremely thin device cavities are fabricated. These devices have very directional emission and higher light extraction efficiency than conventional LEDs. Via the optimization of thin-film growth and refinement of device processing, we decreased the total cavity thickness to less than 1 (micro)m, such that micro-cavity effects were clearly observed and a light extraction efficiency of over 10% was reached. We also began the development of photonic crystals for increased light extraction, in particular for so-called ''guided modes'' which would otherwise propagate laterally in the device and be re-absorbed. Finally, we pursued the growth of smooth, high-quality nonpolar a-plane and m-plane GaN films, as well as blue light emitting diodes on these novel films. Initial nonpolar LEDs showed the expected behavior of negligible peak wavelength shift with increasing drive current. M-plane LEDs in particular show promise, as unpackaged devices had unsaturated optical output power of ∼ 3 mW at 200 mA drive current. The LRC's tasks were aimed at developing the subcomponents necessary for packaging UCSB's light emitting diodes, and packaging them to produce a white light

Annual progress report

International Nuclear Information System (INIS)

Russek, A.

1975-06-01

Progress has been made in calculation of cross-sections for dielectronic and radiative recombination when hot electrons are incident on partially stripped impurity ions. Calculations were completed for the cases of 1 keV and 10 keV electrons incident on ions of arbitrary Z with ionization state consistent with a 1 keV plasma temperature. It was found that dielectronic recombination dominates radiative recombination by a factor of 100 at 1 keV incident electron energy to a factor of 1000 at 10 keV incident electron energy. The work is now being extended to other plasma temperatures and is being improved by more accurate calculation of the matrix elements involved. Progress was also made in the calculation of accurate bremsstrahlung and higher order radiative processes which also occur when hot electrons are incident on partially stripped impurity ions. Formal expressions for the matrix elements have been obtained for cross-sections in a fully relativistic partial wave analysis for bremsstrahlung radiation both with and without electron excitation of the target ion. Final evaluation now awaits the evaluation of the relativistic radial integrals involved in these matrix elements. (U.S.)

Novel Modified Optical Fibers for High Temperature In-Situ Miniaturized Gas Sensors in Advanced Fossil Energy Systems

Energy Technology Data Exchange (ETDEWEB)

Pickrell, Gary [Virginia Polytechnic Institute & State University, Blacksburg, VA (United States); Scott, Brian [Virginia Polytechnic Institute & State University, Blacksburg, VA (United States)

2014-06-30

This report covers the technical progress on the program “Novel Modified Optical Fibers for High Temperature In-Situ Miniaturized Gas Sensors in Advanced Fossil Energy Systems”, funded by the National Energy Technology Laboratory of the U.S. Department of Energy, and performed by the Materials Science & Engineering and Electrical & Computer Engineering Departments at Virginia Tech, and summarizes technical progress from July 1st, 2005 –June 30th, 2014. The objective of this program was to develop novel fiber materials for high temperature gas sensors based on evanescent wave absorption in optical fibers. This project focused on two primary areas: the study of a sapphire photonic crystal fiber (SPCF) for operation at high temperature and long wavelengths, and a porous glass based fiber optic sensor for gas detection. The sapphire component of the project focused on the development of a sapphire photonic crystal fiber, modeling of the new structures, fabrication of the optimal structure, development of a long wavelength interrogation system, testing of the optical properties, and gas and temperature testing of the final sensor. The fabrication of the 6 rod SPCF gap bundle (diameter of 70μm) with a hollow core was successfully constructed with lead-in and lead-out 50μm diameter fiber along with transmission and gas detection testing. Testing of the sapphire photonic crystal fiber sensor capabilities with the developed long wavelength optical system showed the ability to detect CO₂ at or below 1000ppm at temperatures up to 1000°C. Work on the porous glass sensor focused on the development of a porous clad solid core optical fiber, a hollow core waveguide, gas detection capabilities at room and high temperature, simultaneous gas species detection, suitable joining technologies for the lead-in and lead-out fibers and the porous sensor, sensor system sensitivity improvement, signal processing improvement, relationship between pore structure and fiber

46 CFR Appendix B to Subpart C to... - Substance Technical Guidelines, Benzene

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Substance Technical Guidelines, Benzene B Appendix B to... Subpart C to Part 197—Substance Technical Guidelines, Benzene I. Physical and Chemical Data (a) Substance... temperature: 580 °C (1076 °F). (3) Flammable limits in air, % by volume: Lower: 1.3%, Upper: 7.5%. (4...

Technical efficiency and productivity of Chinese county hospitals: an exploratory study in Henan province, China.

Science.gov (United States)

Cheng, Zhaohui; Tao, Hongbing; Cai, Miao; Lin, Haifeng; Lin, Xiaojun; Shu, Qin; Zhang, Ru-Ning

2015-09-09

Chinese county hospitals have been excessively enlarging their scale during the healthcare reform since 2009. The purpose of this paper is to examine the technical efficiency and productivity of county hospitals during the reform process, and to determine whether, and how, efficiency is affected by various factors. 114 sample county hospitals were selected from Henan province, China, from 2010 to 2012. Data envelopment analysis was employed to estimate the technical and scale efficiency of sample hospitals. The Malmquist index was used to calculate productivity changes over time. Tobit regression was used to regress against 4 environmental factors and 5 institutional factors that affected the technical efficiency. (1) 112 (98.2%), 112 (98.2%) and 104 (91.2%) of the 114 sample hospitals ran inefficiently in 2010, 2011 and 2012, with average technical efficiency of 0.697, 0.748 and 0.790, respectively. (2) On average, during 2010-2012, productivity of sample county hospitals increased by 7.8%, which was produced by the progress in technical efficiency changes and technological changes of 0.9% and 6.8%, respectively. (3) Tobit regression analysis indicated that government subsidy, hospital size with above 618 beds and average length of stay assumed a negative sign with technical efficiency; bed occupancy rate, ratio of beds to nurses and ratio of nurses to physicians assumed a positive sign with technical efficiency. There was considerable space for technical efficiency improvement in Henan county hospitals. During 2010-2012, sample hospitals experienced productivity progress; however, the adverse change in pure technical efficiency should be emphasised. Moreover, according to the Tobit results, policy interventions that strictly supervise hospital bed scale, shorten the average length of stay and coordinate the proportion among physicians, nurses and beds, would benefit hospital efficiency. Published by the BMJ Publishing Group Limited. For permission to use (where

Experimental Program Final Technical Progress Report: 15 February 2007 to 30 September 2012

Energy Technology Data Exchange (ETDEWEB)

Kinney, Edward R. [University of Colorado, Boulder, CO

2014-09-12

This is the final technical report of the grant DE-FG02-04ER41301 to the University of Colorado at Boulder entitled "Intermediate Energy Nuclear Physics" and describes the results of our funded activities during the period 15 February 2007 to 30 September 2012. These activities were primarily carried out at Fermilab, RHIC, and the German lab DESY. Significant advances in these experiments were carried out by members of the Colorado group and are described in detail.

Physics of correlated systems. Technical progress report, December 1996 - June 1999

International Nuclear Information System (INIS)

Greene, C.H.

1999-01-01

During the current funding period, which covers a period of approximately 2.5 years, the authors have tackled a number of challenging problems that involve nonperturbative particle-particle interactions in two qualitatively different areas: electron-electron interactions in photoionization and photodetachment, and atom-atom interactions in Bose-Einstein condensates. The following discusses the progress achieved in these different areas. The emphasis in this summary will concentrate on approximately the last year of research accomplishments, although the bibliography below includes all research publications that were supported during the time period of this grant

Radiology and the internet, basic principles and technical requirements

International Nuclear Information System (INIS)

Boegl, K.

2000-01-01

As a new communication media the Internet has revolutionized the global exchange of information which is one of the major sources of progress in medicine. This article reviews the history of the Internet's evolution and describes some fundamental technical concepts. The importance of Internet services for everyday professional work is examined with special consideration of radiology. Special emphasis is laid on the current technical limitations that have delayed a broad practical implementation of tele-medical applications. As a highly innovative medical speciality, radiology has always been at the forefront of research and development in the field of clinical Internet applications. By taking a look at recent innovations, the impact of the Internet on the radiologist's working environment of the future is highlighted. (orig.) [de

Technical report on the accelerators

Energy Technology Data Exchange (ETDEWEB)

Bex, L [ed.

1996-12-31

GANIL operation and the technical studies performed in 1994 are described. The milestones for 1994 are: SISSI (Source d`Ions Secondaires a Supraconducteurs Intense) has been in operation and used for secondary beam production with four different primary beams. The 100 kV platform for beam injection in the CO1 has been in operation for production of metallic beams which demand is increasing. Finally the SPIRAL project (Systeme de Production d`Ions Radioactifs Acceleres en Ligne) is in progress. In late 1994 the civil work has started in view of the installation of the machine in the north part of the GANIL machine building. (K.A.). 48 refs.

Technical report on the accelerators

International Nuclear Information System (INIS)

Bex, L.

1995-01-01

GANIL operation and the technical studies performed in 1994 are described. The milestones for 1994 are: SISSI (Source d'Ions Secondaires a Supraconducteurs Intense) has been in operation and used for secondary beam production with four different primary beams. The 100 kV platform for beam injection in the CO1 has been in operation for production of metallic beams which demand is increasing. Finally the SPIRAL project (Systeme de Production d'Ions Radioactifs Acceleres en Ligne) is in progress. In late 1994 the civil work has started in view of the installation of the machine in the north part of the GANIL machine building. (K.A.)

Review and comment on the advanced spent fuel management process (1): Technical aspects and non-proliferation concerns

International Nuclear Information System (INIS)

Song, Yo Taik

2001-01-01

Efforts are made to analyze the project, the Advanced Spent Fuel Management Technology (ASFMT), which is currently carried out at Korea Atomic Energy Research Institute, on the technical feasibility and validity as well as on the nuclear non-proliferation concerns. The project is a part of a program under the 'Long and Midterm Nuclear Development Program'. On the technical analysis, reviewed the papers presented at the national and international meetings on the subject by KAERI staffs, and also participated to various technical discussions on the 'Mock-up Test', currently in progress. On the non-proliferation concerns, the ASFMT project was reviewed and analyzed in reference to various programs currently in progress or in a formulation stages in US, such as the DOE TOPS and ATW. Further reviewed the past JASNEC process and programs for possible application of the ASFMT project for JASNEC project. Provided a few thoughts for effectively carrying out the ASFMT project, and a plan for the next phase is presented

Review and comment on the advanced spent fuel management process (1): Technical aspects and non-proliferation concerns

Energy Technology Data Exchange (ETDEWEB)

Song, Yo Taik

2001-01-01

Efforts are made to analyze the project, the Advanced Spent Fuel Management Technology (ASFMT), which is currently carried out at Korea Atomic Energy Research Institute, on the technical feasibility and validity as well as on the nuclear non-proliferation concerns. The project is a part of a program under the 'Long and Midterm Nuclear Development Program'. On the technical analysis, reviewed the papers presented at the national and international meetings on the subject by KAERI staffs, and also participated to various technical discussions on the 'Mock-up Test', currently in progress. On the non-proliferation concerns, the ASFMT project was reviewed and analyzed in reference to various programs currently in progress or in a formulation stages in US, such as the DOE TOPS and ATW. Further reviewed the past JASNEC process and programs for possible application of the ASFMT project for JASNEC project. Provided a few thoughts for effectively carrying out the ASFMT project, and a plan for the next phase is presented.

Technical basis for a minimum hydroxide concentration in tanks containing dilute waste

International Nuclear Information System (INIS)

Zapp, P.E.

1995-05-01

Laboratory tests were performed to address the protection of waste tank steel from corrosion in situations of elevated temperatures up to 75 C (hot spots) in the sludge layer of Extended Sludge Processing (ESP) tanks. Coupon immersion tests were conducted at 75 C in two ESP simulants at four hydroxide (or pH) levels. The nitrite concentrations of the simulants were calculated from the ESP technical standards based on a temperature of 40 C. The results showed that a hydroxide concentration of at least 0.01 M prevented significant corrosion of the steel at the elevated temperature. This conclusion provides the technical basis for the revised minimum hydroxide concentration of 0.01 M in the draft WSRC 241-82H Control Room Process Requirements, for the ESP tanks

Study and realization of a new humid air generator; towards the definition of a dew temperature reference; Etude et realisation d'un nouveau generateur d'air humide; vers la definition d'une reference en temperature de rosee

Energy Technology Data Exchange (ETDEWEB)

Blanquart, B.

2001-03-01

The air humidity is an important parameter for several biological and physico-chemical processes. The aim of this thesis is the direct determination of the dew temperature without any link with the gravimetric reference. This document presents the realization and adjusting of a new humid air generator for the -80 deg. C to +15 deg. C range and the uncertainty linked with the dew temperature of the humid air generated. The first chapter recalls the definitions of humid air related data and the principles of the apparatuses used for the measurement of air humidity. The second chapter deals with temperature measurements while chapter 3 describes the new humid air generator built around an 'ideal' cell based on the theoretical definition of the dew temperature. Technical constraints due to temperature measurement and to hygrometers calibration are progressively integrated and introduced and lead to the practical realization of the device. Differences between the ideal cell and the prototype are estimated using a theoretical approach of mass and heat exchanges coupled with experimental results obtained with a previous prototype. Chapter 4 presents a first status of the device uncertainties with some possibilities of reduction of these uncertainties. (J.S.)

The Development of CBM Vocabulary Measures: Grade 5. Technical Report #1212

Science.gov (United States)

Alonzo, Julie; Anderson, Daniel; Park, Bitnara Jasmine; Tindal, Gerald

2012-01-01

In this technical report, we describe the development and piloting of a series of vocabulary assessments intended for use with students in grades two through eight. These measures, available as part of easyCBM[TM], an online progress monitoring and benchmark/screening assessment system, were developed in 2010 and administered to approximately 1200…

The Development of CBM Vocabulary Measures: Grade 7. Technical Report #1214

Science.gov (United States)

Alonzo, Julie; Anderson, Daniel; Park, Bitnara Jasmine; Tindal, Gerald

2012-01-01

In this technical report, we describe the development and piloting of a series of vocabulary assessments intended for use with students in grades two through eight. These measures, available as part of easyCBM[TM], an online progress monitoring and benchmark/screening assessment system, were developed in 2010 and administered to approximately 1200…

The Development of CBM Vocabulary Measures: Grade 6. Technical Report # 1213

Science.gov (United States)

Alonzo, Julie; Anderson, Daniel; Park, Bitnara Jasmine; Tindal, Gerald

2012-01-01

In this technical report, we describe the development and piloting of a series of vocabulary assessments intended for use with students in grades two through eight. These measures, available as part of easyCBM[TM], an online progress monitoring and benchmark/screening assessment system, were developed in 2010 and administered to approximately 1200…

The Development of CBM Vocabulary Measures: Grade 3. Technical Report #1210

Science.gov (United States)

Alonzo, Julie; Anderson, Daniel; Park, Bitnara Jasmine; Tindal, Gerald

2012-01-01

In this technical report, we describe the development and piloting of a series of vocabulary assessments intended for use with students in grades two through eight. These measures, available as part of easyCBM[TM], an online progress monitoring and benchmark/screening assessment system, were developed in 2010 and administered to approximately 1200…

The Development of CBM Vocabulary Measures: Grade 4. Technical Report #1211

Science.gov (United States)

Alonzo, Julie; Anderson, Daniel; Park, Bitnara Jasmine; Tindal, Gerald

2012-01-01

In this technical report, we describe the development and piloting of a series of vocabulary assessments intended for use with students in grades two through eight. These measures, available as part of easyCBM[TM], an online progress monitoring and benchmark/screening assessment system, were developed in 2010 and administered to approximately 1200…

The Development of CBM Vocabulary Measures: Grade 8. Technical Report #1215

Science.gov (United States)

Alonzo, Julie; Anderson, Daniel; Park, Bitnara Jasmine; Tindal, Gerald

2012-01-01

In this technical report, we describe the development and piloting of a series of vocabulary assessments intended for use with students in grades two through eight. These measures, available as part of easyCBM[TM], an online progress monitoring and benchmark/screening assessment system, were developed in 2010 and administered to approximately 1200…

The Development of CBM Vocabulary Measures: Grade 2. Technical Report #1209

Science.gov (United States)

Alonzo, Julie; Anderson, Daniel; Park, Bitnara Jasmine; Tindal, Gerald

2012-01-01

In this technical report, we describe the development and piloting of a series of vocabulary assessments intended for use with students in grades two through eight. These measures, available as part of easyCBM[TM], an online progress monitoring and benchmark/screening assessment system, were developed in 2010 and administered to approximately 1200…

submitter Technical Note: Using DEG-CPCs at upper tropospheric temperatures

CERN Document Server

Wimmer, D; Nieminen, T; Duplissy, J; Ehrhart, S; Almeida, J; Rondo, L; Franchin, A; Kreissl, F; Bianchi, F; Manninen, H E; Kulmala, M; Curtius, J; Petäjä, T

2015-01-01

Over the last few years, several condensation particle counters (CPCs) capable of measuring in the sub-3 nm size range have been developed. Here we study the performance of CPCs based on diethylene glycol (DEG) at different temperatures during Cosmics Leaving OUtdoor Droplets (CLOUD) measurements at CERN. The data shown here are the first set of verification measurements for sub-3 nm CPCs under upper tropospheric temperatures using atmospherically relevant aerosol particles. To put the results in perspective we calibrated the DEG-CPC at room temperature, resulting in a cut-off diameter of 1.4 nm. All diameters refer to mobility equivalent diameters in this paper. At upper tropospheric temperatures ranging from 246.15 K to 207.15 K, we found cut-off sizes relative to a particle size magnifier in the range of 2.5 to 2.8 nm. Due to low number concentration after size classification, the cut-off diameters have a high uncertainty (±0.3 nm) associated with them. Operating two laminar flow DEG-CPCs with different c...

Progress report of the Teilinstitut Nukleare Festkoerperphysik

International Nuclear Information System (INIS)

Geerk, J.; Linker, G.

1977-10-01

This progress report of the Teilinstitut Nukleare Festkoerperphysik covers the period from June 1sup(st), 1976 - May 31sup(st), 1977. The arrangement has been chosen to emphasize the main research areas the institute is presently involved. These areas are the Dynamics of Solids and Liquids, the Electronic Structure and Magnetism of Solids, and the Development and Investigation of New Materials. Some of the technical developments relevant to these topics are also included. (orig.) [de

Review of scientific and technical options for the Superconducting Super Collider Program

International Nuclear Information System (INIS)

Dombeck, T.

1993-11-01

This document is a review of options for the Superconducting Super Collider (SSC) Program. It is the result of an informal study by an ad-hoc working group consisting of Laboratory physicists and engineers who investigated the physics and technical implications of a number of possible alternative SSC programs. Previous studies have shown, and early in this study it was confirmed, that a collider of approximately 20 TeV protons on 20 TeV protons with a luminosity of 10 33 cm -2 s -1 at each interaction region is needed to support a physics program that is guaranteed to answer existing particle physics questions and make new discoveries. Therefore, all options considered in this document were consistent with attainment of these original goals for the SSC. One promising option considered was a program of colliding anti-protons on protons as a possible means to reduce the cost of the SSC by eliminating one of the Collider rings. However, the luminosity requirements to obtain the SSC physics goals remains the same as for protons colliding with protons and this study confirms that even though progress has been made over the last ten years in obtaining the high intensity anti-proton beams necessary, a luminosity higher than 10 32 cannot be guaranteed. Other options were examined to see what advantages could be derived by departing from the SSC baseline program, either in schedule, in parameters, by staging, or by combinations of these options. Even though we considered re-examination of the cost of the baseline program to be beyond the scope of this document, differential cost savings were estimated. Finally, a brief survey of progress over the last ten years in various technical areas that might lead to more cost effective engineering designs was included in this study, such as higher magnetic field magnets resulting from lower operating temperatures or higher current-carrying superconducting materials

Review of scientific and technical options for the Superconducting Super Collider Program

Energy Technology Data Exchange (ETDEWEB)

Dombeck, T.

1993-11-01

This document is a review of options for the Superconducting Super Collider (SSC) Program. It is the result of an informal study by an ad-hoc working group consisting of Laboratory physicists and engineers who investigated the physics and technical implications of a number of possible alternative SSC programs. Previous studies have shown, and early in this study it was confirmed, that a collider of approximately 20 TeV protons on 20 TeV protons with a luminosity of 10{sup 33} cm{sup {minus}2}s{sup {minus}1} at each interaction region is needed to support a physics program that is guaranteed to answer existing particle physics questions and make new discoveries. Therefore, all options considered in this document were consistent with attainment of these original goals for the SSC. One promising option considered was a program of colliding anti-protons on protons as a possible means to reduce the cost of the SSC by eliminating one of the Collider rings. However, the luminosity requirements to obtain the SSC physics goals remains the same as for protons colliding with protons and this study confirms that even though progress has been made over the last ten years in obtaining the high intensity anti-proton beams necessary, a luminosity higher than 10{sup 32} cannot be guaranteed. Other options were examined to see what advantages could be derived by departing from the SSC baseline program, either in schedule, in parameters, by staging, or by combinations of these options. Even though we considered re-examination of the cost of the baseline program to be beyond the scope of this document, differential cost savings were estimated. Finally, a brief survey of progress over the last ten years in various technical areas that might lead to more cost effective engineering designs was included in this study, such as higher magnetic field magnets resulting from lower operating temperatures or higher current-carrying superconducting materials.

Recent Progress on the Key Materials and Components for Proton Exchange Membrane Fuel Cells in Vehicle Applications

Directory of Open Access Journals (Sweden)

Cheng Wang

2016-07-01

Full Text Available Fuel cells are the most clean and efficient power source for vehicles. In particular, proton exchange membrane fuel cells (PEMFCs are the most promising candidate for automobile applications due to their rapid start-up and low-temperature operation. Through extensive global research efforts in the latest decade, the performance of PEMFCs, including energy efficiency, volumetric and mass power density, and low temperature startup ability, have achieved significant breakthroughs. In 2014, fuel cell powered vehicles were introduced into the market by several prominent vehicle companies. However, the low durability and high cost of PEMFC systems are still the main obstacles for large-scale industrialization of this technology. The key materials and components used in PEMFCs greatly affect their durability and cost. In this review, the technical progress of key materials and components for PEMFCs has been summarized and critically discussed, including topics such as the membrane, catalyst layer, gas diffusion layer, and bipolar plate. The development of high-durability processing technologies is also introduced. Finally, this review is concluded with personal perspectives on the future research directions of this area.

Safety related design and economic aspects of HTGRs. Proceedings of a technical committee meeting

International Nuclear Information System (INIS)

2001-04-01

The purpose of the Technical Committee Meeting (TCM) was to provide the opportunity to review the status of design and development activities associated with safety related and economic aspects of HTGRs, and to identify pathways which may provide the opportunity for international cooperation in addressing these issues. The HTGR, as a nuclear heat source for the safe, economic and efficient production of electricity and high temperature industrial processes has, within the past few years, become a significantly increasing influence in the future of nuclear power. Nuclear test facilities with the capability of achieving core outlet temperatures to 950 deg. C are presently under construction in China and Japan. These plants will be utilized to support HTGR research and development activities, including electricity generation via the gas turbine and validation of high temperature process heat applications. Also, major development programmes focusing on the generation of electricity through the direct cycle gas turbine are in progress by ESKOM, the state electric utility of South Africa, and by a consortium of organizations from the Russian Federation, USA, France and Japan. Other national programmes focusing on research and development of the HTGR are underway including the Netherlands, where an evaluation is being completed on a heat and power co-generation plant utilizing a small direct cycle HTR; in Germany, where the primary focus is centered on basic issues of reactor safety and innovative reactor technology; in Indonesia with the evaluation of process heat applications such as coal liquefaction, hydrogen production and high temperature reforming of methane; and in the USA with the recent re-introduction of national support for the HTGR specifically directed to the burning of weapons plutonium. The status information presented in several of the papers is as of the time of drafting. Thus other later material should be referenced for more current status information

Safety related design and economic aspects of HTGRs. Proceedings of a technical committee meeting

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-04-01

The purpose of the Technical Committee Meeting (TCM) was to provide the opportunity to review the status of design and development activities associated with safety related and economic aspects of HTGRs, and to identify pathways which may provide the opportunity for international cooperation in addressing these issues. The HTGR, as a nuclear heat source for the safe, economic and efficient production of electricity and high temperature industrial processes has, within the past few years, become a significantly increasing influence in the future of nuclear power. Nuclear test facilities with the capability of achieving core outlet temperatures to 950 deg. C are presently under construction in China and Japan. These plants will be utilized to support HTGR research and development activities, including electricity generation via the gas turbine and validation of high temperature process heat applications. Also, major development programmes focusing on the generation of electricity through the direct cycle gas turbine are in progress by ESKOM, the state electric utility of South Africa, and by a consortium of organizations from the Russian Federation, USA, France and Japan. Other national programmes focusing on research and development of the HTGR are underway including the Netherlands, where an evaluation is being completed on a heat and power co-generation plant utilizing a small direct cycle HTR; in Germany, where the primary focus is centered on basic issues of reactor safety and innovative reactor technology; in Indonesia with the evaluation of process heat applications such as coal liquefaction, hydrogen production and high temperature reforming of methane; and in the USA with the recent re-introduction of national support for the HTGR specifically directed to the burning of weapons plutonium. The status information presented in several of the papers is as of the time of drafting. Thus other later material should be referenced for more current status information

National Waste Terminal Storage Program. Progress report, October 1, 1976--September 30, 1977

International Nuclear Information System (INIS)

Asher, J.M.

1978-04-01

The National Waste Terminal Storage Program Report comprises five sections: technical projects, facility projects, planning and analysis, regulatory affairs, and public affairs. Progress made in these areas during the period October 1, 1976, to September 30, 1977, is reported

U.C. Davis high energy particle physics research: Technical progress report -- 1990

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-12-31

Summaries of progress made for this period is given for each of the following areas: (1) Task A--Experiment, H1 detector at DESY; (2) Task C--Experiment, AMY detector at KEK; (3) Task D--Experiment, fixed target detectors at Fermilab; (4) Task F--Experiment, PEP detector at SLAC and pixel detector; (5) Task B--Theory, particle physics; and (6) Task E--Theory, particle physics.

Heavy-Section Steel Irradiation Program. Volume 5, No. 2, Progress report, April 1994--September 1994

International Nuclear Information System (INIS)

Corwin, W.R.

1995-07-01

The Heavy-Section Steel Irradiation (HSSI) Program has been established with its primary goal to provide a thorough, quantitative assessment of the effects of neutron irradiation on the material behavior and the fracture toughness properties of typical pressure-vessel steels as they relate to light-water RPV integrity. Effects of specimen size; material chemistry; product form and microstructure; irradiation fluence, flux, temperature, and spectrum; and postirradiation annealing are being examined on a wide range of fracture properties. The HSSI Program is arranged into 14 tasks: (1) program management, (2) fracture toughness curve shift in high-copper weldments (Series 5 and 6), (3) K lc and K la curve shifts in low upper-shelf (LUS) welds (Series 8), (4) irradiation effects in a commercial LUS weld (Series 10), (5) irradiation effects on weld heat-affected zone and plate materials (Series 11), (6) annealing effects in LUS welds (Series 9), (7) microstructural and microfracture analysis of irradiation effects, (8) in-service irradiated and aged material evaluations, (9) Japan Power Development Reactor (JPDR) steel examination, (10) fracture toughness curve shift method, (11) special technical assistance, (12) technical assistance for Joint Coordinating Committee on Civilian Nuclear Reactor Safety (JCCCNRS) Working Groups 3 and 12, (13) correlation monitor materials, and (14) test reactor coordination. Progress on each task is reported

Divisional progress reports for period 1 July 1982 to 30 June 1983

International Nuclear Information System (INIS)

1984-09-01

This progress report deals with technical and research work done at the AAEC Research establishment for the period 1 July 1982 to 30 June 1983. Work done in the following divisions is reported: Applied Mathematics and Computing, Applied Physics, Environmental Science, Isotope, Materials, Nuclear Technology

METHOD IMPROVEMENT FOR DETERMINING THE TECHNICAL LEVEL OF CIVIL AIRCRAFT

Directory of Open Access Journals (Sweden)

2016-01-01

Full Text Available Aircraft are high-tech engineering products which are characterized by a wide range of properties including the two most important groups that respectively characterize the efficiency and technical level.Improving the aircraft efficiency is an essential factor for air transport development, but the efficiency can not be fully describe the technical system, especially in forecasting and new technology requirements development. Aircraft de- signer must evaluate the prospects of a technical solution, but it’s not always possible to calculate the efficiency accuratelyat the design stage. The operator should be able to choose the most technically-advanced aircraft available in the market inorder not to let it grow obsolete quickly. This determines the need for non-economic evaluation of technical systems that can be done by assessment of their technical level.The technical level is a general index that includes a set of technical perfection indicators. Technical perfection is reflected in terms of material and energy intensity, in terms of ergonomics, safety, etc. and is achieved as a result of origi- nal design solutions, the use of new high-strength low-density materials, the introduction of advanced technological pro-cesses, calculation methods, verification, testing, etc.There is a tight connection between the product properties and its weight, because weight is the material reflection of these properties. Therefore, improvement of the product properties usually leads to an intense increase of its weight. To deal with this phenomenon is only possible with widely using scientific and technical progress results. In accordance with this, the technical perfection can be interpreted as a major component of quality that is created without the weight increase. This approach requires investment in research and testing new technical solutions.The method was developed to determine the technical level of civil long-haul aircraft which has been modified to

BX in situ oil shale project. Annual technical progress report, March 1, 1979-February 29, 1980 and quarterly technical progress report, December 1, 1979-February 29, 1980

Energy Technology Data Exchange (ETDEWEB)

Dougan, P.M.

1980-03-20

During the year, design, construction and installation of all project equipment was completed, and continuous steam injection began on September 18, 1979 and continued until February 29, 1980. In the five-month period of steam injection, 235,060 barrels of water as steam at an average wellhead pressure of 1199 psig and an average wellhead temperature of 456/sup 0/F were injected into the eight project injection wells. Operation of the project at design temperature and pressure (1000/sup 0/F and 1500 psig) was not possible due to continuing problems with surface equipment. Environmental monitoring at the project site continued during startup and operation.

World progress toward fusion energy

International Nuclear Information System (INIS)

Clarke, J.F.

1989-09-01

This paper will describe the progress in fusion science and technology from a world perspective. The paper will cover the current technical status, including the understanding of fusion's economic, environmental, and safety characteristics. Fusion experiments are approaching the energy breakeven condition. An energy gain (Q) of 30 percent has been achieved in magnetic confinement experiments. In addition, temperatures required for an ignited plasma (Ti = 32 KeV) and energy confinements about 75 percent of that required for ignition have been achieved in separate experiments. Two major facilities have started the experimental campaign to extend these results and achieve or exceed Q = 1 plasma conditions by 1990. Inertial confinement fusion experiments are also approaching thermonuclear conditions and have achieved a compression factor 100-200 times liquid D-T. Because of this progress, the emphasis in fusion research is turning toward questions of engineering feasibility. Leaders of the major fusion R and D programs in the European Community (EC), Japan, the United States, and the U.S.S.R. have agreed on the major steps that are needed to reach the point at which a practical fusion system can be designed. The United States is preparing for an experiment to address the last unexplored scientific issue, the physics of an ignited plasma, during the late 1990's. The EC, Japan, U.S.S.R., and the United States have joined together under the auspices of the International Atomic Energy Agency (IAEA) to jointly design and prepare the validating R and D for an international facility, the International Thermonuclear Experimental Reactor (ITER), to address all the remaining scientific issues and to explore the engineering technology of fusion around the turn of the century. In addition, a network of international agreements have been concluded between these major parties and a number of smaller fusion programs, to cooperate on resolving a complete spectrum of fusion science and

A new semiquantitative method for evaluation of metastasis progression.

Science.gov (United States)

Volarevic, A; Ljujic, B; Volarevic, V; Milovanovic, M; Kanjevac, T; Lukic, A; Arsenijevic, N

2012-01-01

Although recent technical advancements are directed toward developing novel assays and methods for detection of micro and macro metastasis, there are still no reports of reliable, simple to use imaging software that could be used for the detection and quantification of metastasis in tissue sections. We herein report a new semiquantitative method for evaluation of metastasis progression in a well established 4T1 orthotopic mouse model of breast cancer metastasis. The new semiquantitative method presented here was implemented by using the Autodesk AutoCAD 2012 program, a computer-aided design program used primarily for preparing technical drawings in 2 dimensions. By using the Autodesk AutoCAD 2012 software- aided graphical evaluation we managed to detect each metastatic lesion and we precisely calculated the average percentage of lung and liver tissue parenchyma with metastasis in 4T1 tumor-bearing mice. The data were highly specific and relevant to descriptive histological analysis, confirming reliability and accuracy of the AutoCAD 2012 software as new method for quantification of metastatic lesions. The new semiquantitative method using AutoCAD 2012 software provides a novel approach for the estimation of metastatic progression in histological tissue sections.

Advanced light source: Compendium of user abstracts and technical reports,1993-1996

Energy Technology Data Exchange (ETDEWEB)

None, None

1997-04-01

This compendium contains abstracts written by users summarizing research completed or in progress from 1993-1996, ALS technical reports describing ongoing efforts related to improvement in machine operations and research and development projects, and information on ALS beamlines planned through 1998. Two tables of contents organize the user abstracts by beamline and by area of research, and an author index makes abstracts accessible by author and by principal investigator. Technical details for each beamline including whom to contact for additional information can be found in the beamline information section. Separate abstracts have been indexed into the database for contributions to this compendium.

Technical Note: Updated durability/composition relationships for Hanford high-level waste glasses

International Nuclear Information System (INIS)

Piepel, G.F.; Hartley, S.A.; Redgate, P.E.

1996-03-01

This technical note presents empirical models developed in FYI 995 to predict durability as functions of glass composition. Models are presented for normalized releases of B, Li, Na, and Si from the 7-day Product Consistency Test (PCT) applied to quenched and canister centerline cooled (CCC) glasses as well as from the 28-day Materials Characterization Center-1 (MCC-1) test applied to quenched glasses. Models are presented for Composition Variation Study (CVS) data from low temperature melter (LTM) studies (Hrma, Piepel, et al. 1994) and high temperature melter (HTM) studies (Vienna et al. 1995). The data used for modeling in this technical note are listed in Appendix A

Technical challenges of superconductivity and cryogenics in pursuing TESLA-TTF

International Nuclear Information System (INIS)

Shu, Quan-Sheng

1996-01-01

TESLA (TeV Energy Superconducting Linear Accelerator) Collaboration is an international R ampersand D effort towards the development of an e + e - linear collider with 500 GeV center of mass by means of 20 km active superconducting accelerating structures at a frequency of 1.3 GHz. The ultimate challenges faced by the TESLA project are (1) to raise operational accelerating gradients to 25 MV/m from current world level of 5-10 MV/m, and (2) to reduce construction costs (cryomodules, klystrons, etc.) down to $2,000/MV from now about $40,000/MV. The TESLA Collaboration is building a prototype TESLA test facility (TTF) of a 500 MeV superconducting linear accelerator to establish the technical basis. TTF is presently under construction and will be commissioned at DESY in 1997, through the joint efforts of 24 laboratories from 8 countries. Significant progress has been made in reaching the high accelerating gradient of 25 MV/m in superconducting cavities, developing cryomodules and constructing TTF infrastructure, etc. This paper will briefly discuss the challenges being faced and review the progress achieved in the technical area of superconductivity and cryogenics by the TESLA Collaboration

Technical Meeting on Fast Reactors and Related Fuel Cycle Facilities with Improved Economic Characteristics. Working Material

International Nuclear Information System (INIS)

2013-01-01

In recent years, engineering oriented work, rather than basic research and development (R&D), has led to significant progress in improving the economics of innovative fast reactors and associated fuel cycle facilities, while maintaining and even enhancing the safety features of these systems. Optimization of plant size and layout, more compact designs, reduction of the amount of plant materials and the building volumes, higher operating temperatures to attain higher generating efficiencies, improvement of load factor, extended core lifetimes, high fuel burnup, etc. are good examples of achievements to date that have improved the economics of fast neutron systems. The IAEA, through its Technical Working Group on Fast Reactors (TWG-FR) and Technical Working Group on Nuclear Fuel Cycle Options and Spent Fuel Management (TWG-NFCO), devotes many of its initiatives to encouraging technical cooperation and promoting common research and technology development projects among Member States with fast reactor and advanced fuel cycle development programmes, with the general aim of catalysing and accelerating technology advances in these fields. In particular the theme of fast reactor deployment, scenarios and economics has been largely debated during the recent IAEA International Conference on Fast Reactors and Related Fuel Cycles: Safe Technologies and Sustainable Scenarios, held in Paris in March 2013. Several papers presented at this conference discussed the economics of fast reactors from different national and regional perspectives, including business cases, investment scenarios, funding mechanisms and design options that offer significant capital and energy production cost reductions. This Technical Meeting on Fast Reactors and Related Fuel Cycle Facilities with Improved Economic Characteristics addresses Member States’ expressed need for information exchange in the field, with the aim of identifying the main open issues and launching possible initiatives to help and

Los Alamos National Laboratory Environmental Restoration Project quarterly technical report, April--June 1994

Energy Technology Data Exchange (ETDEWEB)

1994-08-18

This quarterly report describes the technical status of activities in the Los Alamos National Laboratory Environmental Restoration (ER) Project. Each activity is identified by an activity data sheet number, a brief title describing the activity or the technical area where the activity is located, and the name of the project leader. The Hazardous and Solid Waste Amendments (HSWA) portion of the facility operating permit requires the submission of a technical progress report on a quarterly basis. This report, submitted to fulfill the permit`s requirement, summarizes the work performed and the results of sampling and analysis in the ER Project. Suspect waste found include: Radionuclides, high explosives, metals, solvents and organics. The data provided in this report have not been validated. These data are considered ``reviewed data.``

AFR spent fuel storage program. Technical progress report, January 1981-March 1981

International Nuclear Information System (INIS)

1981-01-01

Work on this project is focused on developing design and licensing information for the model facility. Deliverables were submitted to DOE for facility modification, security design, and licensing documentation. Work is essentially complete on the high-density rack design with deliverable planned for April 30, 1981. A continuing program for completion of design and licensing information development was initiated by AGNS in February 1981. Progress to date is satisfactory

Progress report for a research program in computational physics: Progress report, January 1, 1988-December 31, 1988

International Nuclear Information System (INIS)

Guralnik, G.S.

1988-01-01

The project of this progress report are all ultimately concerned with various aspects of numerical simulations of lattice gauge theories. These aspects include algorithms, machines, theoretical studies and actual simulations. We made progress in four general areas: studies of new algorithms, determination of the SU(3) β-function, studies of the finite temperature QCD phase transition in the presence of fermions, and the calculation of hadronic matrix elements. We will describe each of these in turn. 7 refs

Savannah River Plant Works Technical Department monthly progress report for May 1958: Deleted Version

Energy Technology Data Exchange (ETDEWEB)

1958-06-17

This progress report by the Atomic Energy Division of the Savannah River Plant covers: Reactor Technology; Separation Technology; Engineering Assistance; Health Physics; and General Laboratory Work. (JT)

E-Division semiannual report. Progress report, December 1, 1976--May 30, 1977

International Nuclear Information System (INIS)

Kelley, P.A.

1977-11-01

Detector research and development are described first. Then, briefer reports are given on research on the following topics: electronic temperature monitoring and identification for livestock, electromagnetic probing (for fracture mapping), fiber optics for downhole instrumentation (for weapons testing), adaptive control applied to HVAC systems, energy environmental simulator, and high-temperature electronics. Engineering support (development projects, program support, instrumentation support) and technical services (general group activities, recharge programs, research and development programs, minicomputer maintenance, information and training services) are sketched. The report is basically administrative in nature, with a minimum of technical material. 47 figures, 10 tables

Lower-Temperature Subsurface Layout and Ventilation Concepts

International Nuclear Information System (INIS)

Christine L. Linden; Edward G. Thomas

2001-01-01

This analysis combines work scope identified as subsurface facility (SSF) low temperature (LT) Facilities System and SSF LT Ventilation System in the Technical Work Plan for Subsurface Design Section FY 01 Work Activities (CRWMS M and O 2001b, pp. 6 and 7, and pp. 13 and 14). In accordance with this technical work plan (TWP), this analysis is performed using AP-3.10Q, Analyses and Models. It also incorporates the procedure AP-SI.1Q, Software Management. The purpose of this analysis is to develop an overall subsurface layout system and the overall ventilation system concepts that address a lower-temperature operating mode for the Monitored Geologic Repository (MGR). The objective of this analysis is to provide a technical design product that supports the lower-temperature operating mode concept for the revision of the system description documents and to provide a basis for the system description document design descriptions. The overall subsurface layout analysis develops and describes the overall subsurface layout, including performance confirmation facilities (also referred to as Test and Evaluation Facilities) for the Site Recommendation design. This analysis also incorporates current program directives for thermal management

FY2011 Annual Progress Report for Advanced Combustion Engine Research and Development

Energy Technology Data Exchange (ETDEWEB)

none,

2011-12-01

Annual Progress Report for the Advanced Combustion Engine Research and Development (R&D) subprogram supporting the mission of the Vehicle Technologies Program by removing the critical technical barriers to commercialization of advanced internal combustion engines (ICEs) for passenger and commercial vehicles that meet future federal emissions regulations.

Ultra-high temperature direct propulsion

International Nuclear Information System (INIS)

Araj, K.J.; Slovik, G.; Powell, J.R.; Ludewig, H.

1987-01-01

Potential advantages of ultra-high exhaust temperature (3000 K - 4000 K) direct propulsion nuclear rockets are explored. Modifications to the Particle Bed Reactor (PBR) to achieve these temperatures are described. Benefits of ultra-high temperature propulsion are discussed for two missions - orbit transfer (ΔV = 5546 m/s) and interplanetary exploration (ΔV = 20000 m/s). For such missions ultra-high temperatures appear to be worth the additional complexity. Thrust levels are reduced substantially for a given power level, due to the higher enthalpy caused by partial disassociation of the hydrogen propellant. Though technically challenging, it appears potentially feasible to achieve such ultra high temperatures using the PBR

1985. Progress annual report

International Nuclear Information System (INIS)

1986-06-01

Tore Supra construction has been vigorously continued. The whole cryogenic system has been entirely delivered. On TFR priority has been given to electron cyclotron resonance heating; but also neutral heating mechanisms, pellet injection, plasma-wall interaction in the presence of pumped limiter, impurity transport and plasma turbulence have been studied and progress on diagnostics have been made. On Petula, with lower hybrid wave, the numerous results on ion heating, current drive, plasma stability in the presence of non-inductive current and on Tore Supra technical problems are important. At last, theoretical and numerical results are concerned with plasma equilibrium macroscopic evolution of plasma, RF heating, plasma instabilities, magnetic islands, turbulence, transport coefficients and spectroscopy [fr

Fusion reactor materials. Semiannual progress report for period ending September 30, 1993

Energy Technology Data Exchange (ETDEWEB)

Rowcliffe, A.F.; Burn, G.L.; Knee`, S.S.; Dowker, C.L. [comps.

1994-02-01

This is the fifteenth in a series of semiannual technical progress reports on fusion reactor materials. This report combines research and development activities which were previously reported separately in the following progress reports: Alloy Development for Irradiation Performance; Damage Analysis and Fundamental Studies; Special purpose Materials. These activities are concerned principally with the effects of the neutronic and chemical environment on the properties and performance of reactor materials; together they form one element of the overall materials programs being conducted in support of the Magnetic Fusion Energy Program of the U.S. Department of Energy. The Fusion Reactor Materials Program is a national effort involving several national laboratories, universities, and industries. The purpose of this series of reports is to provide a working technical record for the use of the program participants, and to provide a means of communicating the efforts of materials scientists to the rest of the fusion community, both nationally and worldwide.

Habit formation, work ethics, and technological progress

OpenAIRE

Faria, João Ricardo; León-Ledesma, Miguel A.

2002-01-01

Work ethics affects labor supply. This idea is modeled assuming that work is habit forming. This paper introduces working habits in a neoclassical growth model and compares its outcomes with a model without habit formation. In addition, it analyzes the impact of different forms of technical progress. The findings are that i) labor supply in the habit formation case is higher than in the neoclassical case; ii) unlike in the neoclassical case, labor supply in the presence of habit formation wil...

FY2013 Energy Storage R&D Progress Report

Energy Technology Data Exchange (ETDEWEB)

none,

2014-02-01

The FY 2013 Progress Report for Energy Storage R&D focuses on advancing the development of batteries to enable a large market penetration of hybrid and electric vehicles. Program targets focus on overcoming technical barriers to enable market success including: (1) significantly reducing battery cost, (2) increasing battery performance (power, energy, durability), (3) reducing battery weight & volume, and (4) increasing battery tolerance to abusive conditions such as short circuit, overcharge, and crush.

Geological disposal of high level radioactive waste in China: progress during 1985-2004

International Nuclear Information System (INIS)

Wang Ju; Xu Guoqing; Zheng Hualing; Fan Xianhua; Wang Chengzu; Fan Zhiwen

2005-01-01

Safe disposal of high level radioactive waste (HLW) is a challenging issue for the sustainable development of nuclear energy. The studies for the disposal of HLW in China started in 1985, the proposed goal was to build China's high level waste repository by mid-21st Century, while the waste to be disposed of will be vitrified waste, transuranic waste and small amount of spent fuel. The proposed repository was a shaft-tunnel-silo model hosted by granite in saturated zone. In the period of 1985 to 2004, progress was made in China's HLW disposal program. It was decided that 'deep geological disposal' will be used to dispose of China's HLW, while the technical strategy for the development of repository will a 3-step strategy, that includes steps of site selection and site evaluation, construction of underground research laboratory, and construction of repository. Based on nation wide screening, the Beishan area, Gansu Province, northwestern China, located in Gobi desert area with few inhabitants, integral crust structure and favorable geological and hydrogeological conditions, was selected as the most potential area for China's repository. In early 1990's, site selection for underground research laboratory was conducted, 2 sites in the suburb of Beijing were preliminarily selected as the potential sites for a 'generic underground research laboratory'. It was determined to use bentonite as backfill material for the repository, while the bentonite from Gaomiaozi deposit in Inner Mongolia was selected as potential buffer and backfill material for China's repository. The studies on the mineralogical, geotechnical, physico-mechanical and thermal properties of the Gaomiaozi bentonite have been conducting. Some parameters such as sorption radio, diffusion coefficient and dispersion coefficient of radionuclides (Np, Pu and Tc) in Beishan granite and bentonite have been obtained. A low-oxygen glove box and a device simulating the temperature, pressure and redox potential of

Environmental Management Science Program awards. Fiscal year 1997 annual progress report

Energy Technology Data Exchange (ETDEWEB)

Simmons, A. [ed.; Benner, W.H.; DePaolo, D.J.; Faybishenko, B.; Majer, E.L.; Pallavicini, M.; Russo, R.E.; Shultz, P.G.; Wan, J.

1997-10-01

Lawrence Berkeley National Laboratory was awarded eight Environmental Management Science Program (EMSP) research grants in Fiscal Year 1996. This report summarizes the progress of each grant in addressing significant DOE site cleanup issues after completion of the first year of research. The technical progress made to date in each of the research projects is described in greater detail in individual progress reports. The focus of the research projects covers a diversity of areas relevant to site cleanup, including bioremediation, health effects, characterization, and mixed waste. Some of the projects cut across a number of focus areas. Three of the projects are directed toward characterization and monitoring at the Idaho National Engineering and Environmental Laboratory, as a test case for application to other sites.

Environmental Management Science Program awards. Fiscal year 1997 annual progress report

International Nuclear Information System (INIS)

Simmons, A.; Benner, W.H.; DePaolo, D.J.; Faybishenko, B.; Majer, E.L.; Pallavicini, M.; Russo, R.E.; Shultz, P.G.; Wan, J.

1997-10-01

Lawrence Berkeley National Laboratory was awarded eight Environmental Management Science Program (EMSP) research grants in Fiscal Year 1996. This report summarizes the progress of each grant in addressing significant DOE site cleanup issues after completion of the first year of research. The technical progress made to date in each of the research projects is described in greater detail in individual progress reports. The focus of the research projects covers a diversity of areas relevant to site cleanup, including bioremediation, health effects, characterization, and mixed waste. Some of the projects cut across a number of focus areas. Three of the projects are directed toward characterization and monitoring at the Idaho National Engineering and Environmental Laboratory, as a test case for application to other sites

High-temperature plasma physics

International Nuclear Information System (INIS)

Furth, H.P.

1988-03-01

Both magnetic and inertial confinement research are entering the plasma parameter range of fusion reactor interest. This paper reviews the individual and common technical problems of these two approaches to the generation of thermonuclear plasmas, and describes some related applications of high-temperature plasma physics

A comment on technical naturalness and the cosmological constant

International Nuclear Information System (INIS)

Itzhaki, Nissan

2006-01-01

We propose a model of dynamical relaxation of the cosmological constant. Technical naturalness of the model and the present value of the vacuum energy density imply an upper bound on the supersymmetry breaking scale and the reheating temperature at the TeV scale

Progress report 1998

International Nuclear Information System (INIS)

1999-01-01

The O.P.R.I. is in charge of environmental general surveillance and follow-up of natural exposures; To monitor the nuclear installations, it carries out samples campaigns. The technical follow-up of medical installations concerns it too. The workers radiation protection as well as the public protection are in its attributions. We find in particular, three sanitary studies: about the North Cotentin, (the question of excess of leukemia or not, and due or not to the facility of La hague) Nogent-sur-Marne (the case of a nursery school built on a old factory using radium), and the situation of populations living in French Polynesia, areas that have worried the public with alarmist announcements published in newspapers. All the results relative to the radiations measurements for 1998 appear in this progress report. (N.C.)

Technical change in US industry: A cross-industry analysis

Science.gov (United States)

Nelson, R. R. (Editor)

1981-01-01

The nature of the public policies which have influenced the pace and pattern of technical progress in a number of American industries is studied with the view of assessing the broad effects of these policies. The industries studied are agriculture, pharmaceuticals, semiconductors, computers, civil aircraft, automobiles and residential construction. The policies considered include research and development funding as well as government procurement, education, information dissemination, patent protection, licensing, regulations, and anti-trust policies.

Internet - Technical Developments and Applications 2

CERN Document Server

Tkacz, Ewaryst; Rostanski, Maciej

2012-01-01

The unusual direct progress of civilization in many fields concerning technical sciences is being observed in the period of last two decades. Experiencing extraordinary dynamics of the development of technological processes, particularly in ways of communicating, makes us believe that  the information society is coming into existence. Having the information in today’s world of changing attitudes and socio-economic conditions can be perceived as one of the most important advantages. The content of this book is divided into four parts: ·         Mathematical and technical fundamentals, ·         Information management systems and project management ·         Information security and business continuity management ·         Interdisciplinary problems This monograph has been prepared to contribute in a significant way to the success of implementing consequences of human imagination  into social life. The authors believe that this monograph will influence the further technol...

Developing Technical Writing Skills in the Physical Chemistry Laboratory: A Progressive Approach Employing Peer Review

Science.gov (United States)

Gragson, Derek E.; Hagen, John P.

2010-01-01

Writing formal "journal-style" lab reports is often one of the requirements chemistry and biochemistry students encounter in the physical chemistry laboratory. Helping students improve their technical writing skills is the primary reason this type of writing is a requirement in the physical chemistry laboratory. Developing these skills is an…

LFCM [liquid-fed ceramic melter] vitrification technology: Quarterly progress report, January--March 1987

International Nuclear Information System (INIS)

Brouns, R. A.; Allen, C. R.; Powell, J. A.

1988-05-01

This report is compiled by the Nuclear Waste Treatment Program and the Hanford Waste Vitrification Program at Pacific Northwest Laboratory to describe the progress in developing, testing, applying and documenting liquid-fed ceramic melter vitrification technology. Progress in the following technical subject areas during the second quarter of FY 1987 is discussed: melting process chemistry and glass development, feed preparation and transfer systems, melter systems, canister filling and handling systems, and process/product modeling. 23 refs., 14 figs., 10 tabs

The AECL study for an intense neutron - generator (technical details)

Energy Technology Data Exchange (ETDEWEB)

Bartholomew, G A; Tunnicliffe, P R

1966-07-01

The AECL study for an intense neutron-generator has been in progress for two years. Recently the scientific and technical details and the conceptual designs were compiled in a report supporting proposals addressed to AECL's Board of Directors for further work. The compilation is being issued in this form to permit further discussion of the technical aspects. However readers are asked to appreciate that it was written primarily for an AECL audience, and specifically that those chapters giving tentative information about costs, the rate of investment and similar items have been omitted or modified, many references have been made to interim internal reports in order to complete the local documentation, but these references do not imply that the reports themselves can be made generally available. (author)

The AECL study for an intense neutron - generator (technical details)

International Nuclear Information System (INIS)

Bartholomew, G.A.; Tunnicliffe, P.R.

1966-01-01

The AECL study for an intense neutron-generator has been in progress for two years. Recently the scientific and technical details and the conceptual designs were compiled in a report supporting proposals addressed to AECL's Board of Directors for further work. The compilation is being issued in this form to permit further discussion of the technical aspects. However readers are asked to appreciate that it was written primarily for an AECL audience, and specifically that those chapters giving tentative information about costs, the rate of investment and similar items have been omitted or modified, many references have been made to interim internal reports in order to complete the local documentation, but these references do not imply that the reports themselves can be made generally available. (author)

Research in elementary particle physics: Technical progress report, June 1, 1987-May 31, 1988

International Nuclear Information System (INIS)

Kirsch, L.E.; Schnitzer, H.J.; Abbott, L.F.; Bensinger, J.R.; Blocker, C.A.

1988-01-01

The main topics discussed in the progress report: electron/photon algorithm groups; W and Z analysis; heavy quark analysis; gas gain monitoring; database upgrade; CDF test beam studies; string theory; cosmology; and neutral networks

Temperature control of the graphite stack of the reactor RBMK-1500

International Nuclear Information System (INIS)

Lesnoj, S.

1998-01-01

The paper includes general information about RBMK-1500 reactor, construction features and main technical data; graphite moderator stack, temperature channel, thermocouple TXA-1379, its basic technical and metrologic parameters as well as its advantages and disadvantages

Progress in fusion

International Nuclear Information System (INIS)

1959-01-01

Controlled thermonuclear fusion is now the biggest challenge before atomic science, not only because of the exceedingly difficult nature of the problem but also because of the virtually limitless benefit that, it is expected, will eventually flow from its solution. It might be pointed out that if some of the early optimism is now inevitably moderated, that is only because there is now a better understanding of the difficulties and, consequently, of the basic scientific and technical problems. The basic problem, as is now widely known, is to heat heavy hydrogen gas to a temperature at which the nuclei will fuse by moving so fast as to overcome their mutual electrical repulsion, and simultaneously to keep the gas in a state of extreme density so that the nuclei may collide against each other, fuse, release-energy in the form of heat, and thus set in a kind of thermal chain reaction. The temperature required is of a fantastically high order, but the scientists are confident that it can be obtained by fantastically powerful electrical discharges. More difficult seems to be the task of making the superheated gas, or the plasma as it is called when completely ionized, to behave obligingly. It must remain in a state of extreme density even when it is heated to a temperature of many millions of degrees. As a matter of fact, it must be contained, so to speak, by itself; it must not touch the walls of its material container and thereby lose some of its heat and, on top of that, evaporate the container. The pinch effect produces a kind of magnetic bottle for containing the plasma, but the trouble seems to be that it is difficult to make the bottle stable and leak-proof. The next task will be to ensure that the output of energy from this fusion is greater than the input of energy to heat the plasma. Intensive research and experiment on these problems have been going on in several countries, notably in the UK, the USA, and the USSR. In all the countries most advanced in

Technical progress report

International Nuclear Information System (INIS)

1982-01-01

This report summarizes the work carried out by personnel at the Nuclear Physics Laboratory of the University of Colorado from about August 1, 1981 to October 1, 1982, under contract with the Department of Energy. The intermediate energy studies summarized in this report were carried out at the meson physics facilities at Los Alamos (LAMPF), the cyclotron at Indiana University (IUCF), and the meson physics facilities at Vancouver (TRIUMF). This year, for the first time, intermediate energy experimental studies are being reported in separate documents from the low energy and theoretical nuclear physics efforts. Experimental studies are reported on pion-nucleus interactions, charge exchange reactions, nucleon transfer reactions, and apparatus development

Geothermal direct-heat utilization assistance. Quarterly project progress report, July 1996--September 1996. Federal Assistance Program

Energy Technology Data Exchange (ETDEWEB)

Lienau, P.

1996-11-01

This report summarizes geothermal technical assistance, R&D and technology transfer activities of the Geo-Heat Center at Oregon Institute of Technology for the fourth quarter of FY-96. It describes 152 contacts with parties during this period related to technical assistance with geothermal direct heat projects. Areas dealt with include geothermal heat pumps, space heating, greenhouses, aquaculture, equipment, economics and resources. Research activities are summarized on greenhouse peaking. Outreach activities include the publication of a geothermal direct use Bulletin, dissemination of information, geothermal library, technical papers and seminars, and progress monitor reports on geothermal resources and utilization.

Technical note: Using distributed temperature sensing for Bowen ratio evaporation measurements

Science.gov (United States)

Schilperoort, Bart; Coenders-Gerrits, Miriam; Luxemburg, Willem; Jiménez Rodríguez, César; Cisneros Vaca, César; Savenije, Hubert

2018-01-01

Rapid improvements in the precision and spatial resolution of distributed temperature sensing (DTS) technology now allow its use in hydrological and atmospheric sciences. Introduced by ) is the use of DTS for measuring the Bowen ratio (BR-DTS), to estimate the sensible and latent heat flux. The Bowen ratio is derived from DTS-measured vertical profiles of the air temperature and wet-bulb temperature. However, in previous research the measured temperatures were not validated, and the cables were not shielded from solar radiation. Additionally, the BR-DTS method has not been tested above a forest before, where temperature gradients are small and energy storage in the air column becomes important. In this paper the accuracy of the wet-bulb and air temperature measurements of the DTS are verified, and the resulting Bowen ratio and heat fluxes are compared to eddy covariance data. The performance of BR-DTS was tested on a 46 m high tower in a mixed forest in the centre of the Netherlands in August 2016. The average tree height is 26 to 30 m, and the temperatures are measured below, in, and above the canopy. Using the vertical temperature profiles the storage of latent and sensible heat in the air column was calculated. We found a significant effect of solar radiation on the temperature measurements, leading to a deviation of up to 3 K. By installing screens, the error caused by sunlight is reduced to under 1 K. Wind speed seems to have a minimal effect on the measured wet-bulb temperature, both below and above the canopy. After a simple quality control, the Bowen ratio measured by DTS correlates well with eddy covariance (EC) estimates (r2 = 0.59). The average energy balance closure between BR-DTS and EC is good, with a mean underestimation of 3.4 W m-2 by the BR-DTS method. However, during daytime the BR-DTS method overestimates the available energy, and during night-time the BR-DTS method estimates the available energy to be more negative. This difference could be

Seizing the Future: How Ohio's Career-Technical Education Programs Fuse Academic Rigor and Real-World Experiences to Prepare Students for College and Careers

Science.gov (United States)

Guarino, Heidi; Yoder, Shaun

2015-01-01

"Seizing the Future: How Ohio's Career and Technical Education Programs Fuse Academic Rigor and Real-World Experiences to Prepare Students for College and Work," demonstrates Ohio's progress in developing strong policies for career and technical education (CTE) programs to promote rigor, including college- and career-ready graduation…

1997 Progress report

Energy Technology Data Exchange (ETDEWEB)

Cecchini, M.; Crescentini, L.; Ghezzi, L. [ENEA, Centro Ricerche Frascati, Rome (Italy). Nuclear fusion division

1997-12-31

1997 was another year of intense activity for the ENEA Nuclear Fusion Division in the evolving scenario of fusion research. With respect to the International Thermonuclear Experimental Reactor (ITER), a major review process has started, originate by the wide perception that the difficult financial situation affecting some of the parties would make it very difficult, practically impossible, to secure funding for the project as it stands. To scale down the size and cost of the machine by reducing the technical objectives, while keeping to the programmatic goal of constructing a demonstration reactor (DEMO) as the following step, appears achievable. Progress in physics was substantial during 1997. Analysis of the huge existing database, complemented by the latest results, had led to a better, more accurate scaling for the confinement time on which to base extrapolation to ITER. Studies of the very promising advanced regimes have been pursued on many tokamaks. The Frascati Tokamak Upgrade (FTU) is well placed in this respect since it is equipped with the right tools, lower hybrid and electron cyclotron radiofrequency heating and current drive systems, to explore the new promised land of low transport from the plasma core. The main highlights of FTU operation in 1997 were related to providing information relevant to these future developments. Transient production of low transport regimes with electron temperatures of 8-9 keV at the plasma center was obtained by taking advantage of the plasma skin effect and precise electron cyclotron power deposition. High-efficiency current drive at high density using lower hybrid waves was demonstrated. High-confinement pellet-enhanced modes of operation and good ion Bernstein wave coupling through the waveguide-type coupler were also achieved. Concerning the IGNITOR experiment, funds were made available only for continuation of the engineering design activities, and nothing has been released so far for manufacturing the additional

1997 Progress report

International Nuclear Information System (INIS)

Cecchini, M.; Crescentini, L.; Ghezzi, L.

1997-01-01

1997 was another year of intense activity for the ENEA Nuclear Fusion Division in the evolving scenario of fusion research. With respect to the International Thermonuclear Experimental Reactor (ITER), a major review process has started, originate by the wide perception that the difficult financial situation affecting some of the parties would make it very difficult, practically impossible, to secure funding for the project as it stands. To scale down the size and cost of the machine by reducing the technical objectives, while keeping to the programmatic goal of constructing a demonstration reactor (DEMO) as the following step, appears achievable. Progress in physics was substantial during 1997. Analysis of the huge existing database, complemented by the latest results, had led to a better, more accurate scaling for the confinement time on which to base extrapolation to ITER. Studies of the very promising advanced regimes have been pursued on many tokamaks. The Frascati Tokamak Upgrade (FTU) is well placed in this respect since it is equipped with the right tools, lower hybrid and electron cyclotron radiofrequency heating and current drive systems, to explore the new promised land of low transport from the plasma core. The main highlights of FTU operation in 1997 were related to providing information relevant to these future developments. Transient production of low transport regimes with electron temperatures of 8-9 keV at the plasma center was obtained by taking advantage of the plasma skin effect and precise electron cyclotron power deposition. High-efficiency current drive at high density using lower hybrid waves was demonstrated. High-confinement pellet-enhanced modes of operation and good ion Bernstein wave coupling through the waveguide-type coupler were also achieved. Concerning the IGNITOR experiment, funds were made available only for continuation of the engineering design activities, and nothing has been released so far for manufacturing the additional

1997 Progress report

Energy Technology Data Exchange (ETDEWEB)

Cecchini, M; Crescentini, L; Ghezzi, L [ENEA, Centro Ricerche Frascati, Rome (Italy). Nuclear fusion division

1998-12-31

1997 was another year of intense activity for the ENEA Nuclear Fusion Division in the evolving scenario of fusion research. With respect to the International Thermonuclear Experimental Reactor (ITER), a major review process has started, originate by the wide perception that the difficult financial situation affecting some of the parties would make it very difficult, practically impossible, to secure funding for the project as it stands. To scale down the size and cost of the machine by reducing the technical objectives, while keeping to the programmatic goal of constructing a demonstration reactor (DEMO) as the following step, appears achievable. Progress in physics was substantial during 1997. Analysis of the huge existing database, complemented by the latest results, had led to a better, more accurate scaling for the confinement time on which to base extrapolation to ITER. Studies of the very promising advanced regimes have been pursued on many tokamaks. The Frascati Tokamak Upgrade (FTU) is well placed in this respect since it is equipped with the right tools, lower hybrid and electron cyclotron radiofrequency heating and current drive systems, to explore the new promised land of low transport from the plasma core. The main highlights of FTU operation in 1997 were related to providing information relevant to these future developments. Transient production of low transport regimes with electron temperatures of 8-9 keV at the plasma center was obtained by taking advantage of the plasma skin effect and precise electron cyclotron power deposition. High-efficiency current drive at high density using lower hybrid waves was demonstrated. High-confinement pellet-enhanced modes of operation and good ion Bernstein wave coupling through the waveguide-type coupler were also achieved. Concerning the IGNITOR experiment, funds were made available only for continuation of the engineering design activities, and nothing has been released so far for manufacturing the additional

An approach to knowledge structuring for advanced phases of the Technical and Management Information System (TMIS)

Science.gov (United States)

Goranson, H. T.

1986-01-01

The Technical and Management Information System (TMIS) must employ on enlightened approach to its object structure, but basic issues in conceptual structuring remain to be resolved. Sirius outlines the necessary agenda and reports on progress toward solutions.

INDOT Technical Training Plan : [Technical Summary

Science.gov (United States)

2012-01-01

A wide range of job classifications, increasing technical : performance expectations, licensing and certification requirements, : budget restrictions and frequent department : reorganization has made technical training of employees : more difficult, ...

Progress report 2011-2013 - Brazilian Energy and Nuclear Research Institute - IPEN

International Nuclear Information System (INIS)

2014-01-01

This progress report presents the results of the R&D center of IPEN in accordance with the main programs: Lasers Technology, Applications of Ionizing Radiations, Biotechnology, Renewable Energies, Radiopharmacy, Nuclear Science and Technology, Environmental Science and Technology, Nuclear Reactors and Fuel Cycle, Materials and Nanotechnology, Nuclear Safety, Education, Brazilian Multipurpose Reactor and Scientific and Technical Production

Fusion materials semiannual progress report for period ending December 31, 1999

Energy Technology Data Exchange (ETDEWEB)

Burn, G.

2000-03-01

This is the twenty-seventh in a series of semiannual technical progress reports on fusion materials. This report combines the full spectrum of research and development activities on both metallic and non-metallic materials with primary emphasis on the effects of the neutronic and chemical environment on the properties and performance of materials for in-vessel components.

Fusion materials semiannual progress report for period ending December 31, 1999

International Nuclear Information System (INIS)

Burn, G.

2000-01-01

This is the twenty-seventh in a series of semiannual technical progress reports on fusion materials. This report combines the full spectrum of research and development activities on both metallic and non-metallic materials with primary emphasis on the effects of the neutronic and chemical environment on the properties and performance of materials for in-vessel components

Progress report 2008-2010 - Brazilian Energy and Nuclear Research Institute - IPEN

International Nuclear Information System (INIS)

2011-01-01

This progress report presents the results of the R and D center of IPEN in the areas of: Lasers Technology; Renewable Energies; Nuclear Reactors and Fuel Cycle; Applications of Ionizing Radiations; Nuclear Science and Technology; Materials and Nanotechnology; Environmental Science and Technology; Radiopharmacy; Nuclear Safety; and Education. Also presents the Technical and Scientific Production od the center

AECL's progress in DUPIC fuel development

International Nuclear Information System (INIS)

Sullivan, J.D.; Ryz, M.A.; Lee, J.W.

1997-01-01

Previous papers described progress in choosing a fabrication route for the DUPIC (Direct Use of Spent PWR Fuel in CANDU) fuel cycle [1], details of the OREOX (Oxidation Reduction of Oxide fuel) process, and preliminary results of out-cell and small-scale in-cell experiments [2]. AECL's project to develop the DUPIC fuel cycle has now progressed to the stage of fabricating DUPIC fuel elements for irradiation testing in a research reactor. Because of the high radiation fields around the spent PWR fuel, all work is being done in hot cells. The equipment used for fabrication of the DUPIC fuel elements is described in this paper. The commissioning, in-cell installation and current status of the fabrication process are also described and plans for the completion of this phase of the DUPIC project are outlined. The goal of this phase of the project is demonstration of the technical feasibility of the DUPIC fuel cycle. (author)

Production of technical silicon and silicon carbide from rice-husk

Directory of Open Access Journals (Sweden)

A. Z. Issagulov

2014-10-01

Full Text Available In the article there are studied physical and chemical properties of silicon-carbonic raw material – rice-husk, thermophysical characteristics of the process of rice-husk pyrolysis in nonreactive and oxidizing environment; structure and phase composition of products of the rice-husk pyrolysis in interval of temperatures 150 – 850 °С and high temperature pyrolysis in interval of temperatures 900 – 1 500 °С. There are defined the silicon-carbon production conditions, which meet the requirements applicable to charging materials at production of technical silicon and silicon carbide.

E-Division semiannual report. Progress report, December 1, 1976--May 30, 1977. [LASL

Energy Technology Data Exchange (ETDEWEB)

Kelley, P.A. (comp.)

1977-11-01

Detector research and development are described first. Then, briefer reports are given on research on the following topics: electronic temperature monitoring and identification for livestock, electromagnetic probing (for fracture mapping), fiber optics for downhole instrumentation (for weapons testing), adaptive control applied to HVAC systems, energy environmental simulator, and high-temperature electronics. Engineering support (development projects, program support, instrumentation support) and technical services (general group activities, recharge programs, research and development programs, minicomputer maintenance, information and training services) are sketched. The report is basically administrative in nature, with a minimum of technical material. 47 figures, 10 tables. (RWR)

Scientific and technical progress in high-energy astrophysics at INPE

International Nuclear Information System (INIS)

Bui-Van, N.A.; Jayanthi, U.B.; Jardim, J.O.D.; Braga, J.; Santo, C.M.E.

1984-01-01

The recent advances in high-energy Astrophysics pertains to the study of compact objects in galactic nuclei, binary systems and pulsars. These aspects are best understood by the study of the emissions in X- and gamma rays of these objects through the temporal variation in flux and spectrum. The Southern Hemisphere offers some of the unique objects for investigations such as galactic center, the Vela pulsar etc. For high temporal and spectra resolution studies two telescopes 'GeLi' and 'Pulsar' were designed and constructed. To support these scientific activities, a program in balloon launching and data acquisition facilities has been developed since 1971. The 'Balloon Launching Center' of INPE has capacity to launch balloons of -850,000 m 3 with payloads weighting about 1,000 Kg. Taking advantage of these facilities, project 'Bantar', with the goal to measure the atmospheric gamma-ray radiation in the Antartic Region, is under progress. (Author) [pt

Heavy Vehicle Propulsion Materials: Recent Progress and Future Plans

International Nuclear Information System (INIS)

D. Ray Johnson; Sidney Diamond

2001-01-01

The Heavy Vehicle Propulsion Materials Program provides enabling materials technology for the U.S. DOE Office of Heavy Vehicle Technologies (OHVT). The technical agenda for the program is based on an industry assessment and the technology roadmap for the OHVT. A five-year program plan was published in 2000. Major efforts in the program are materials for diesel engine fuel systems, exhaust aftertreatment, and air handling. Additional efforts include diesel engine valve-train materials, structural components, and thermal management. Advanced materials, including high-temperature metal alloys, intermetallics, cermets, ceramics, amorphous materials, metal- and ceramic-matrix composites, and coatings, are investigated for critical engine applications. Selected technical issues and planned and ongoing projects as well as brief summaries of several technical highlights are given

Research in elementary particle physics. Technical progress report, June 1, 1983-May 31, 1984

International Nuclear Information System (INIS)

Kirsch, L.E.; Schnitzer, H.J.; Bensinger, J.R.; Abbott, L.F.

1984-01-01

Under this contract, research has been performed on both the theoretical and experimental properties of elementary particles. A brief description of the work which is either in progress or has been completed is given. Publications are listed

Studies on Ta-Ni alloys as high-temperature braze for SiC-SiC joined products; Untersuchungen zu Ta-Ni-Legierungen als Hochtemperaturlot fuer SiC-SiC Verbunde

Energy Technology Data Exchange (ETDEWEB)

Triebert, Anke; Matthey, Bjoern; Martin, Hans-Peter [Fraunhofer Institut fuer Keramische Technologien und Systeme (IKTS), Dresden (Germany)

2011-07-01

Active metal brazes have been already established for a number of decades. The current progress of processing technologies and engineering require new and powerful materials also for high-temperature applications. Up to now there are little technically and industrially applicable brazing materials for operation temperatures above 800 C. The investigations described in this paper concerning the Ta-Ni system intend to be the start of a braze material development, which delivers ceramic-ceramic or ceramic-metal joined products. Besides principal considerations and experiments with regard to the investigated material system of Ta-Ni active metal brazing tests to join SIC-SIC components are presented. The joined ceramic component samples are characterized focusing on their materials structure within the joining zone, their crystalline phases of the braze and their mechanical strength at room temperature and high temperatures. The achieved properties demonstrate that Ta-Ni brazes have the potential for future high temperature brazes for ceramics materials. (orig.)

Identification of mine rescue equipment reduction gears technical condition

Science.gov (United States)

Gerike, B. L.; Klishin, V. I.; Kuzin, E. G.

2017-09-01

The article presents the reasons for adopting intelligent service of mine belt conveyer drives concerning evaluation of their technical condition based on the diagnostic techniques instead of regular preventative maintenance. The article reveals the diagnostic results of belt conveyer drive reduction gears condition taking into account the parameters of lubricating oil, vibration and temperature. Usage of a complex approach to evaluate technical conditions allows reliability of the forecast to be improved, which makes it possible not only to prevent accidental breakdowns and eliminate unscheduled downtime, but also to bring sufficient economic benefits through reduction of the term and scope of work during overhauls.

Electron-dislocation interaction at low temperatures. Progress report

International Nuclear Information System (INIS)

1978-01-01

The interaction of mobile dislocations with electrons in copper and copper alloys has shown that dislocation motion in copper, at low temperature, can be treated as an analog of an underdamped oscillator. We have also shown that the viscous drag on mobile dislocations in type II superconductors can be treated as an acoustic attenuation of an elastic wave

Development of operation and maintenance technology for HTGRs by using HTTR (High Temperature engineering Test Reactor)

Energy Technology Data Exchange (ETDEWEB)

Shimizu, Atsushi, E-mail: shimizu.atsushi35@jaea.go.jp [HTTR Operation Section, Department of HTTR, Oarai Research and Development Center, Japan Atomic Energy Agency, 4002 Narita-cho, Oarai-machi, Higashiibaraki-gun, Ibaraki 311-1393 (Japan); Kawamoto, Taiki [HTTR Operation Section, Department of HTTR, Oarai Research and Development Center, Japan Atomic Energy Agency, 4002 Narita-cho, Oarai-machi, Higashiibaraki-gun, Ibaraki 311-1393 (Japan); Tochio, Daisuke [HTTR Reactor Engineering Section, Department of HTTR, Oarai Research and Development Center, Japan Atomic Energy Agency, 4002 Narita-cho, Oarai-machi, Higashiibaraki-gun, Ibaraki 311-1393 (Japan); Saito, Kenji; Sawahata, Hiroaki; Honma, Fumitaka; Furusawa, Takayuki; Saikusa, Akio [HTTR Operation Section, Department of HTTR, Oarai Research and Development Center, Japan Atomic Energy Agency, 4002 Narita-cho, Oarai-machi, Higashiibaraki-gun, Ibaraki 311-1393 (Japan); Takada, Shoji [HTTR Reactor Engineering Section, Department of HTTR, Oarai Research and Development Center, Japan Atomic Energy Agency, 4002 Narita-cho, Oarai-machi, Higashiibaraki-gun, Ibaraki 311-1393 (Japan); Shinozaki, Masayuki [HTTR Operation Section, Department of HTTR, Oarai Research and Development Center, Japan Atomic Energy Agency, 4002 Narita-cho, Oarai-machi, Higashiibaraki-gun, Ibaraki 311-1393 (Japan)

2014-05-01

To establish the technical basis of HTGR (High Temperature Gas cooled Reactor), the long term high temperature operation using HTTR was carried out in the high temperature test operation mode during 50-day since January till March, 2010. It is necessary to establish the technical basis of operation and maintenance by demonstrating the stability of plant during long-term operation and the reliability of components and facilities special to HTGRs, in order to attain the stable supply of the high temperature heat to the planned heat utilization system of HTTR. Test data obtained in the operation were evaluated for the technical issues which were extracted before the operation. As the results, it was confirmed that the temperatures and flow rate of primary and secondary coolant were well controlled within sufficiently small deviation against the disturbance by the atmospheric temperature variation in daily. Stability and reliability of the components and facility special to HTGRs was demonstrated through the long term high temperature operation by evaluating the heat transfer performance of high temperature components, the stability performance of pressure control to compensate helium gas leak, the reliability of the dynamic components such as helium gas circulators, the performance of heat-up protection of radiation shielding. Through the long term high temperature operation of HTTR, the technical basis for the operation and maintenance technology of HTGRs was established.

Development of operation and maintenance technology for HTGRs by using HTTR (High Temperature engineering Test Reactor)

International Nuclear Information System (INIS)

Shimizu, Atsushi; Kawamoto, Taiki; Tochio, Daisuke; Saito, Kenji; Sawahata, Hiroaki; Honma, Fumitaka; Furusawa, Takayuki; Saikusa, Akio; Takada, Shoji; Shinozaki, Masayuki

2014-01-01

To establish the technical basis of HTGR (High Temperature Gas cooled Reactor), the long term high temperature operation using HTTR was carried out in the high temperature test operation mode during 50-day since January till March, 2010. It is necessary to establish the technical basis of operation and maintenance by demonstrating the stability of plant during long-term operation and the reliability of components and facilities special to HTGRs, in order to attain the stable supply of the high temperature heat to the planned heat utilization system of HTTR. Test data obtained in the operation were evaluated for the technical issues which were extracted before the operation. As the results, it was confirmed that the temperatures and flow rate of primary and secondary coolant were well controlled within sufficiently small deviation against the disturbance by the atmospheric temperature variation in daily. Stability and reliability of the components and facility special to HTGRs was demonstrated through the long term high temperature operation by evaluating the heat transfer performance of high temperature components, the stability performance of pressure control to compensate helium gas leak, the reliability of the dynamic components such as helium gas circulators, the performance of heat-up protection of radiation shielding. Through the long term high temperature operation of HTTR, the technical basis for the operation and maintenance technology of HTGRs was established

Technical evaluation of corium cooling at the reactor cavity

International Nuclear Information System (INIS)

Yang, Soo Hyung; Chan, Eun Sun; Lee, Jae Hun; Lee, Jong In

1998-01-01

To terminate the progression of the severe accident and mitigate the accident consequences, corium cooling has been suggested as one of most important design features considered in the severe accident mitigation. Till now, some kinds of cooling methodologies have been identified and, specially, the corium cooling at the reactor cavity has been considered as one of the most promising cooling methodologies. Moreover, several design requirements related to the corium cooling at the reactor cavity have been also suggested and applied to the design of the next generation reactor. In this study, technical descriptions are briefly described for the important issues related to the corium cooling at the reactor cavity, i.e. cavity area, cavity flooding system, etc., and simple evaluations for those items have been performed considering present technical levels including the experiment and analytical works

High Temperature Chemistry of Aromatic Hydrocarbons. Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Scott, Lawrence T. [Boston College, Chestnut Hill, MA (United States). Merkert Chemistry Center, Dept. of Chemistry

2017-05-15

The primary goal of this research was to uncover the principal reaction channels available to polycyclic aromatic hydrocarbons (PAHs) at high temperatures in the gas phase and to establish the factors that determine which channels will be followed in varying circumstances. New structure-property relationships for PAHs were also studied. The efficient production of clean energy from fossil fuels will remain a major component of the DOE mission until alternative sources of energy eventually displace coal and petroleum. Hydrocarbons constitute the most basic class of compounds in all of organic chemistry, and as the dominant species in fossil fuels, they figure prominently into the programs of the DOE. Much is already known about the normal chemistry of hydrocarbons under ambient conditions, but far less is known about their intrinsic chemistry at temperatures close to those reached during combustion. An understanding of the fundamental molecular transformations, rearrangements, and interconversions of PAHs at high temperatures in the gas phase, as revealed by careful studies on small, well-designed, molecular systems, provides insights into the underlying chemistry of many important processes that are more complex, such as the generation of energy by the combustion of fossil fuels, the uncatalyzed gasification and liquefaction of coal, the production of fullerenes in fuel-rich flames, and the formation of soot and carcinogenic pollutants in smoke (e.g., benzo[a]pyrene). The rational control of any of these processes, whether it be the optimization of a desirable process or the minimization of an undesirable one, requires a clear knowledge of the basic chemistry that governs the fate of the species involved. Advances in chemistry at the most fundamental level come about primarily from the discovery of new reactions and from new insights into how reactions occur. Harnessing that knowledge is the key to new technologies. The recent commercialization of a combustion

Biology Division progress report, June 1, 1980-July 31, 1982

Energy Technology Data Exchange (ETDEWEB)

1982-12-01

Highlights of progress for the period June 1980 through July 1982 are summarized. Discussions of projects are presented under the following headings: molecular and cellular sciences; cellular and comparative mutagenesis; mammalian genetics and teratology; toxicology; and carcinogenesis. In addition this report includes an outline of educational activities. Separate abstracts have been prepared for individual technical reports for inclusion in the Energy Data Base. (RJC)

High beta and second stability region transport and stability analysis: Technical progress report

International Nuclear Information System (INIS)

Hughes, M.H.; Phillips, M.W.

1995-03-01

This report summarizes MHD equilibrium and stability studies carried out at Northrop Grumman's Advanced Technology and Development Center during the 12 month period starting March 1, 1994. Progress is reported in both ideal and resistive MHD modeling of TFTR plasmas. The development of codes to calculate the significant effects of highly anisotropic pressure distributions is discussed along with results from this model

High beta and second stability region transport and stability analysis. Technical progress report

International Nuclear Information System (INIS)

Hughes, M.H.; Phillips, M.W.

1994-09-01

This report summarizes MHD equilibrium and stability studies carried out at Grumman's Corporate Research Center during the 6 month period starting March 1, 1994. Progress is reported in both ideal and resistive MHD modeling of TFTR plasmas. The development of codes to calculate the significant effects of highly anisotropic pressure distributions is discussed along with initial results from this model

Fusion materials semiannual progress report for the period ending March 31, 1995

International Nuclear Information System (INIS)

1995-07-01

This is the eighteenth in a series of semiannual technical progress reports on fusion materials. This report combines research and development activities which were previously reported separately in the following progress reports: sm-bullet Alloy Development for Irradiation Performance. sm-bullet Damage Analysis and Fundamental Studies. sm-bullet Special Purpose Materials. These activities are concerned principally with the effects of the neutronic and chemical environment on the properties and performance of reactor materials; together they form one element of the overall materials programs being conducted in support of the Magnetic Fusion Energy Program of the US Department of Energy. The other major element of the program is concerned with the interactions between reactor materials and the plasma and is reported separately. The Fusion Materials Program is a national effort involving several national laboratories, universities, and industries. The purpose of this series of reports is to provide a working technical record for the use of the program participants, and to provide a means of communicating the efforts of materials scientists to the rest of the fusion community, both nationally and worldwide. This report has been compiled and edited under the guidance of A.F. Rowcliffe by Gabrielle Burn, Oak Ridge National Laboratory. Their efforts, and the efforts of the many persons who made technical contributions, are gratefully acknowledged

Fusion materials semiannual progress report for the period ending March 31, 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

This is the eighteenth in a series of semiannual technical progress reports on fusion materials. This report combines research and development activities which were previously reported separately in the following progress reports: {sm_bullet} Alloy Development for Irradiation Performance. {sm_bullet} Damage Analysis and Fundamental Studies. {sm_bullet} Special Purpose Materials. These activities are concerned principally with the effects of the neutronic and chemical environment on the properties and performance of reactor materials; together they form one element of the overall materials programs being conducted in support of the Magnetic Fusion Energy Program of the US Department of Energy. The other major element of the program is concerned with the interactions between reactor materials and the plasma and is reported separately. The Fusion Materials Program is a national effort involving several national laboratories, universities, and industries. The purpose of this series of reports is to provide a working technical record for the use of the program participants, and to provide a means of communicating the efforts of materials scientists to the rest of the fusion community, both nationally and worldwide. This report has been compiled and edited under the guidance of A.F. Rowcliffe by Gabrielle Burn, Oak Ridge National Laboratory. Their efforts, and the efforts of the many persons who made technical contributions, are gratefully acknowledged.

Development of nuclear technology through International Technical Cooperation programme: Malaysian experience

International Nuclear Information System (INIS)

Ainul Hayati Daud

1997-01-01

In the advent of new technologies and knowledge, countries need to rely on one another for progress and development. At the same time, new challenges to development, which are beyond the competence of any country to approach individually, have emerged. These have led to greater need for international co-operation, particularly among the developing countries. In Malaysia, international technical co-operation has contributed significantly towards the development of nuclear technology. Malaysia has received technical assistance through the multilateral, regional and bilateral co-operation. This assistance complements the efforts of the government to meet the primary objectives of science and technology programme, which are; intensification of R and D capacity and applications of technologies, both acquired and developed, in national development. Over the last one and a half decade, more than 70 projects valued almost USD 15 millions, were implemented under the Technical Assistance Programme of the International Atomic Energy Agency and the Bilateral Technical Assistance Programme of Japan and Australia. Malaysia also has benefited from the regional technical co-operation programme such Regional Co-operative Agreement for Asia and Pacific Region, United Nation Department Programme, International Nuclear Co-operation in Asia. While receiving assistance, Malaysia continues to assist other developing countries in their development efforts in the fields of nuclear technology, through the various international co-operation programmes. This report reviews the technical assistance received through the international co-operation and its contributions towards the development of nuclear technology in Malaysia for period 1980 - 1996

Study on severe fuel damage and in-vessel melt progression

International Nuclear Information System (INIS)

Kim, Hee Dong; Kim, Sang Baik; Lee, Gyu Jung

1992-06-01

In-vessel core melt progression describes the progression of the state of a reactor core from core uncovery up to reactor vessel melt through in uncovered accidents or through temperature stabilization in accidents recovered by core reflooding. Melt progression can be thought as two parts; early melt progression and late melt progression. Early phase of core melt progression includes the progression of core material melting and relocation, which mostly consist of metallic materials. On the other hand, the late phase of core melt progression involves ceramic material melt and relocation to the lower plenum and heat-up the reactor vessel lower head. A large number of information are available for the early melt progression through experiments such as SFD, DF, FLHT test and utilized in the severe accident analysis codes. However, understanding of the late phase melt progression phenomenology is based primary on TMI-2 core examinations and not much experimental information is available. Especilally, the great uncertainties exist in vessel failure mode, melt composition, mass, and temperature. Further research is planned to perform to reduce the uncertainties in understanding of core melt down accidents as parts of long term melt progression research program. A study on the core melt progression at KAERI has been being performed through the Severe Accident Research Program with USNRC. KAERI staff had participated in the PBF SFD experiments at INEL and analyses of experiments were performed using SCDAP code. Experiments of core melt program have not been carried out at KAERI yet. It is planned that further research on core melt down accidents will be performed, which is related to design of future generations of nuclear reactors as parts of long-term project for improvement of nuclear reactor safety. (Author)

Theory of high-energy-collision processes. Technical progress report, January 1-December 31, 1981

International Nuclear Information System (INIS)

1982-01-01

Progress is described in the following areas: (1) several years ago, surprisingly simple expressions were obtained for the differential cross sections of e + e - → μ + μ - γ and e + e - → e + e - γ at high energies. Such simple expressions were generalized to twelve other similar radiative processes in QED and QCD. Afterwards, it was found that these results can be derived easily with the help of helicity amplitudes. This method is being investigated for many other radiative processes; (2) in the two-dimensional Ising model, the horizontal and vertical interaction energies are usually taken to be different. When this idea of different interactions in different directions is applied to the Z 2 lattice gauge theory in four dimensions, a limiting case is found which is exactly solvable. Contrary to numerical calculations at the symmetry point, the phase transition is found to be of second order; (3) on the subject of supersymmetry, general helicity and spin sum rules were obtained for massless and massive supermultiplets, and a functional integral approach was found as a natural setting for Witten's criterion for the occurrence of dynamic symmetry breaking of supersymmetry. A systematic and exhaustive analysis of explicit soft breaking of global supersymmetry has also been carried out using the methods of superfields; (4) the renormalization of the massless Thirring model in the neighborhood of g = -π/2 was studied. The results are consistent with those found previously by placing the model on a lattice; and (5) in studying the effect of laboratory temperature on scattering processes, it was found that transport phenomena play an important role. As a preparation for this study, an exactly solvable case of the nonlinear Boltzmann equation has been found and studied

Progress in automation, robotics and measuring techniques

CERN Document Server

Zieliński, Cezary; Kaliczyńska, Małgorzata

2015-01-01

This book presents recent progresses in control, automation, robotics, and measuring techniques. It includes contributions of top experts in the fields, focused on both theory and industrial practice. The particular chapters present a deep analysis of a specific technical problem which is in general followed by a numerical analysis and simulation, and results of an implementation for the solution of a real world problem. The presented theoretical results, practical solutions and guidelines will be useful for both researchers working in the area of engineering sciences and for practitioners solving industrial problems.    .

Progress report of the nuclear physics department

International Nuclear Information System (INIS)

1988-01-01

This progress report presents the research programs and the technical developments carried out at the Nuclear Physics Department of Saclay from October 1, 1986 to September 30, 1987. The research programs concern the structure of nuclei and the general study of nuclear reaction mechanisms. Experiments use electromagnetic probes of the 700 Mev Saclay linear electron accelerator and hadronic probes, light polarised particles and heavy ions of the National Laboratories SATURNE and GANIL. The Nuclear Physics Department is also involved in development of accelerator technologies, especially in the field of superconducting cavities [fr

Progress report of the nuclear physics department

International Nuclear Information System (INIS)

1987-01-01

This progress report presents the experiments and the technological studies carried out at the Nuclear Physics Department of Saclay from October 1, 1985 to September 30, 1986. These studies concern the structure of nuclei, the nuclear reaction mechanisms and, more and more, mesic processes in nuclear dynamics. The experiments have been carried at the 700 MeV electron linac, the synchrotron SATURNE, the heavy ion accelerator GANIL, the SARA facility at Grenoble. An important technical activity has been devoted to the construction of the supraconducting booster of the 9 MV tandem [fr

Safety research programs sponsored by Office of Nuclear Regulatory Research: Progress report, January 1--June 30, 1988

Energy Technology Data Exchange (ETDEWEB)

Baum, J W; Boccio, J L; Diamond, D; Fitzpatrick, R; Ginsberg, T; Greene, G A; Guppy, J G; Hall, R E; Higgins, J C; Weiss, A J [comp.

1988-12-01

This progress report describes current activities and technical progress in the programs at Brookhaven National Laboratory sponsored by the Division of Regulatory Applications, Division of Engineering, Division of Safety Issue Resolution, and Division of Systems Research of the US Nuclear Regulatory Commission, Office of Nuclear Regulatory Research following the reorganization in July 1988. The previous reports have covered the period October 1, 1976 through December 31, 1987.

Safety research programs sponsored by Office of Nuclear Regulatory Research: Progress report, October 1--December 31, 1988

Energy Technology Data Exchange (ETDEWEB)

Weiss, A J; Azarm, A; Baum, J W; Boccio, J L; Carew, J; Diamond, D J; Fitzpatrick, R; Ginsberg, T; Greene, G A; Guppy, J G; Haber, S B

1989-07-01

This progress report describes current activities and technical progress in the programs at Brookhaven National Laboratory sponsored by the Division of Regulatory Applications, Division of Engineering, Division of Safety Issue Resolution, and Division of Systems Research of the US Nuclear Regulatory Commission, Office of Nuclear Regulatory Research following the reorganization in July 1988. The previous reports have covered the period October 1, 1976 through September 30, 1988.

Safety research programs sponsored by Office of Nuclear Regulatory Research: Progress report, January 1--June 30, 1988

International Nuclear Information System (INIS)

Baum, J.W.; Boccio, J.L.; Diamond, D.

1988-12-01

This progress report describes current activities and technical progress in the programs at Brookhaven National Laboratory sponsored by the Division of Regulatory Applications, Division of Engineering, Division of Safety Issue Resolution, and Division of Systems Research of the US Nuclear Regulatory Commission, Office of Nuclear Regulatory Research following the reorganization in July 1988. The previous reports have covered the period October 1, 1976 through December 31, 1987

Features of formation spirituality pictures of the world in youth in in the era of information-highlytechnological scientific and technical progress

Directory of Open Access Journals (Sweden)

N. V. Polishchuk

2016-06-01

Full Text Available In clause necessity of formation of a spiritual picture of the world, anthropocosmos at young generation at the present stage of development much crisis world and, including, the Ukrainian society is proved. In the article the necessity of formation of anthropocosmos-spiritual picture of the world at young generation at the present stage of development bagalicious the world and, in particular, of the Ukrainian society. The proposed definition of new terms: anthropocosmos is a spiritual picture of the world, anthropocosmic spirituality, anthropocosmic worldview and other anthropocentric concepts and definitions in contemporary philosophical and pedagogical discourse. The presented model of the formation of anthropocosmos-spiritual worldview of the young generation in the information and high-tech scientific and technical progress and the author’s interpretation of its philosophical, educational, pedagogical and spiritual essence. It is proved, that having generated in consciousness of the young man a anthropocosmos-spiritual picture of the world, will allow it in conditions of inevitable crash in the near future of a human civilization, if it will not solve present global-civilizational crises and will not avoid geocosmic accidents, to understand sense space-ekzoplanete lives which will be esclusivi, and, therefore, crisis-free, conflict-free, comprehensive and meaningful, anthropocosmos-highly spiritual (divine M. Berdyaev, and, therefore, progressive and virtually eternal as the life of society, which is composed of such anthropocosmos educated individuals. Solved zagalnoosvitnioi sense anthropocosmos spiritual world picture, which is to solve the problem of the choice of life strategies of mankind, the search for new ways of civilization development, in particular, resettlement anthropocosmos-conscious part of humanity for exoplanets space with the aim of preserving the gene pool of humanity and creation of human cosmically

FY2011 Progress Report for Energy Storage Research & Development

Energy Technology Data Exchange (ETDEWEB)

none,

2012-01-31

The FY 2011 Progress Report for Energy Storage R&D focuses on advancing the development of batteries to enable a large market penetration of hybrid and electric vehicles. Program targets focus on overcoming technical barriers to enable market success including: (1) significantly reducing battery cost, (2) increasing battery performance (power, energy, durability), (3) reducing battery weight & volume, and (4) increasing battery tolerance to abusive conditions such as short circuit, overcharge, and crush.

Waste Isolation Safety Assessment Program. Technical progress report for FY-1978

International Nuclear Information System (INIS)

Brandstetter, A.; Harwell, M.A.; Howes, B.W.; Benson, G.L.; Bradley, D.J.; Raymond, J.R.; Serne, R.J.; Schilling, A.H.

1979-07-01

Associated with commercial nuclear power production in the United States is the generation of potentially hazardous radioactive wastes. The Department of Energy (DOE) is seeking to develop nuclear waste isolation systems in geologic formations that will preclude contact with the biosphere of waste radionuclides in concentrations which are sufficient to cause deleterious impact on humans or their environments. Comprehensive analyses of specific isolation systems are needed to assess the expectations of meeting that objective. The Waste Isolation Safety Assessment Program (WISAP) has been established at the Pacific Northwest Laboratory (operated by Battelle Memorial Institute) for developing the capability of making those analyses. Progress on the following tasks is reported: release scenario analysis, waste form release rate analysis, release consequence analysis, sorption-desorption analysis, and societal acceptance analysis

Proceedings of the 18th technical meeting on nuclear reactor and radiation for KURRI engineers and the 9th technical official group section 5 meeting in Kyoto University

International Nuclear Information System (INIS)

2010-03-01

This report is a summary of 18th Technical Meeting on Nuclear Reactor and Radiation for KURRI Engineers in Kyoto University. This was also the 9th meeting for technical official group section 5 (nuclear and radiation) in Kyoto University. In the workshop, three special lectures held were: (1) 'On Border Between Subcritical and Supercritical', (2) 'Memories of Nuclear Power Plant Management for 40 Years', and (3) 'Introduction of Technical Office in Faculty of Engineering, Kyoto University'. The technical presentations held were: (1) 'Radiation Background Study of Specialty Products in Senshu Region', (2) 'Introduction of Radioactivation Analysis at KUR', (3) 'Consideration of Critical Approach Method for KUR Low-Enrichment Fuel Reactor Core Using SRAC', (4) 'Evaluation of Temperature Coefficient of KUR Low-Enrichment Fuel Reactor Core Using SRAC'. As training for technical staffs in Technical Office, we visited the facility in Ashiu Research Forest. An introduction of this facility and the comments from the participants were included in this report. (S.K.)

[Review of draft Crystalline Repository Project reports]: Technical progress report, CY 1985-1986

International Nuclear Information System (INIS)

1986-01-01

During the period (CY 1985-86) of this report, the Wisconsin Radioactive Waste Review Board provided technical services under the contract with DOE. These included Participation in the development of variables and screening techniques that would be used in identifying those rock bodies in the Area Recommendation Report (ARR); reviewing and commenting on the report and developing a procedure in which local residents could have input into the process; sought resumption of negotiations with DOE on a full Consultation and Cooperation (CandC) agreement; and Participating in workshops and provided comments on two major DOE transportation documents, ''Transportation Business Plan: Strategy Options Document,'' and ''Transportation Institutional Plan.''

The AECL study for an intense neutron - generator (technical details)

Energy Technology Data Exchange (ETDEWEB)

Bartholomew, G.A.; Tunnicliffe, P.R

1966-07-01

The AECL study for an intense neutron-generator has been in progress for two years. Recently the scientific and technical details and the conceptual designs were compiled in a report supporting proposals addressed to AECL's Board of Directors for further work. The compilation is being issued in this form to permit further discussion of the technical aspects. However readers are asked to appreciate that it was written primarily for an AECL audience, and specifically that those chapters giving tentative information about costs, the rate of investment and similar items have been omitted or modified, many references have been made to interim internal reports in order to complete the local documentation, but these references do not imply that the reports themselves can be made generally available. (author)

Metals and Ceramics Division progress report for period ending June 30, 1984

Energy Technology Data Exchange (ETDEWEB)

Brogden, I. (ed.)

1984-09-01

This progress report covers the research and development activities of the Metals and Ceramics Division from January 1, 1983, through June 30, 1984. The format of the report follows the organizational structure of the division. Short summaries of technical work in progress in the various experimental groups are presented in six parts. Chapter 1 deals with the research and development activities of the Engineering Materials Section, Chapter 2 with the Processing Science and Technology Section, Chapter 3 with the Materials Science Section, Chapter 4 with Project Activities, Chapter 5 with Specialized Research Facilities and Equipment, and Chapter 6 with Miscellaneous Activities.

Metals and Ceramics Division progress report for period ending June 30, 1984

International Nuclear Information System (INIS)

Brogden, I.

1984-09-01

This progress report covers the research and development activities of the Metals and Ceramics Division from January 1, 1983, through June 30, 1984. The format of the report follows the organizational structure of the division. Short summaries of technical work in progress in the various experimental groups are presented in six parts. Chapter 1 deals with the research and development activities of the Engineering Materials Section, Chapter 2 with the Processing Science and Technology Section, Chapter 3 with the Materials Science Section, Chapter 4 with Project Activities, Chapter 5 with Specialized Research Facilities and Equipment, and Chapter 6 with Miscellaneous Activities

Association Euratom - DTU, Technical University of Denmark, Department of Physics - Annual Progress Report 2012

DEFF Research Database (Denmark)

The programme of the Research Unit of the Fusion Association Euratom – DTU, Technical University of Denmark covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium...... and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology there are activities on fusion materials research (Tungsten and ODSFS). Other activities are system analysis...

Association Euratom - DTU, Technical University of Denmark, Department of Physics - Annual Progress Report 2013

DEFF Research Database (Denmark)

The programme of the Research Unit of the Fusion Association Euratom – DTU, Technical University of Denmark covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium...... and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology there are activities on fusion materials research (Tungsten and ODSFS). Other activities are system analysis...

The Progressive Insurance Automotive X PRIZE Education Program

Energy Technology Data Exchange (ETDEWEB)

Robyn Ready

2011-12-31

The Progressive Insurance Automotive X PRIZE Education Program conducted education and outreach activities and used the competition's technical goals and vehicle demonstrations as a means of attracting students and the public to learn more about advanced vehicle technologies, energy efficiency, climate change, alternative fuels, and the science and math behind efficient vehicle development. The Progressive Insurance Automotive X PRIZE Education Program comprised three integrated components that were designed to educate the general public and create a multi-tiered initiative to engage students and showcase the 21st century skills students will need to compete in our global economy: teamwork, creativity, strong literacy, math and science skills, and innovative thinking. The elements included an Online Experience, a National Student Contest, and in person education events and activites. The project leveraged online connections, strategic partnerships, in-classroom, and beyond-the-classroom initiatives, as well as mainstream media. This education program supported by the U.S. Department of Energy (DOE) also funded the specification of vehicle telemetry and the full development and operation of an interactive online experience that allowed internet users to follow the Progressive Insurance Automotive X PRIZE vehicles as they performed in real-time during the Progressive Insurance Automotive X PRIZE competition events.

Progress of ITER and the way forward

International Nuclear Information System (INIS)

Bigot, Bernard; Jacquinot, Jean

2015-01-01

The ITER project has recently benefited from bold organizational changes which will be first discussed during this presentation. The changes focus on strengthening a common project spirit across the entire organization. This is essential for completing successfully such a challenging undertaking as ITER. All key actors, whether they are in the central team, in the DAs or in other related organizations, should feel committed to the success of the entire Project sharing a common vision and working practices. To that effect, a new organization has been put in place: - Two project teams (Buildings and Vacuum Vessel, other teams are being considered) now gather under a single leadership all components of a major critical deliverable. An Executive Project Board (EPB), meeting twice a month, now convenes DA executives under the chairmanship of the director general (DG) who is empowered, after consultation of the EPB, to take all important technical decisions. The DG can use a recently created reserve fund for financing items or changes in the configuration which were not foreseen in procurement agreements. Finally the organigram of the central team has been simplified emphasizing project-oriented integration, building coherent technical departments and preparing for the assembly phase which will be a major undertaking. The transitional period necessary to put in place these changes did not prevent the Project from accelerating the pace of the construction. The presentation will give examples of major achievements obtained recently. Among these an outstanding result obtained collectively is the progress in the manufacture of the superconducting cables: 90% of the needed cable-in-conduit has been produced fully complying with the technical requirements. This required a major industrial development in several parties. India has made remarkable progress in its assigned procurements: in particular, the bottom parts of the cryostat are expected to reach the ITER site at about

Nuclear measurements and reference materials annual progress report, january - december 1988

International Nuclear Information System (INIS)

1989-01-01

The 1988 progress report of the Central Bureau for Nuclear Measurements (CBNM) is presented. The major changes in the role and orientation of the Joint Research Center, of which CBNM is an institute, are included. The main tasks of CBNM, which involve the program on Nuclear Measurements and Reference Materials, are given. Technical activities concerning the GELINA electron beam and Van de Graaff accelerators are reported. The study of transition radiation at linear electron accelerators, and the development of isotope dilution mass spectrometry, for trace analysis and isotope abundance measurements in iron and gallium, are summarized. The scientific and technical support to the commission, work for third parties, and contribution to conferences are presented

High temperature properties of nuclear reactor coolants and thermodynamic power cycle working fluids. Technical progress report, December 1, 1977--November 30, 1978

International Nuclear Information System (INIS)

Bonilla, C.F.; Holder, G.P.

1978-09-01

The program to determine the surface tension of sodium to high temperatures has been soundly commenced with the completion and calibration of a new all-molybdenum maximum-bubble-pressure apparatus suitable to some 1900 0 K. This property bears on boiling, condensing and two-phase flow phenomena, also related to LMFBR analysis. This same apparatus will be useful with lithium, of interest in fusion reactor cooling. Reduction of prior maximum bubble pressure results on potassium by the Schroedinger method has been repeated by the more precise but time-consuming Sugden procedure, which has increased the resulting surface tension values by an average of 0.27%. Thus the Sugden method will be employed to reduce the data for sodium and lithium

Progressing batch hydrolysis process

Science.gov (United States)

Wright, J.D.

1985-01-10

A progressive batch hydrolysis process is disclosed for producing sugar from a lignocellulosic feedstock. It comprises passing a stream of dilute acid serially through a plurality of percolation hydrolysis reactors charged with feed stock, at a flow rate, temperature and pressure sufficient to substantially convert all the cellulose component of the feed stock to glucose. The cooled dilute acid stream containing glucose, after exiting the last percolation hydrolysis reactor, serially fed through a plurality of pre-hydrolysis percolation reactors, charged with said feedstock, at a flow rate, temperature and pressure sufficient to substantially convert all the hemicellulose component of said feedstock to glucose. The dilute acid stream containing glucose is cooled after it exits the last prehydrolysis reactor.

Waste Isolation Safety Assessment Program. Technical progress report for FY-1978

Energy Technology Data Exchange (ETDEWEB)

Brandstetter, A.; Harwell, M.A.; Howes, B.W.; Benson, G.L.; Bradley, D.J.; Raymond, J.R.; Serne, R.J.; Schilling, A.H.

1979-07-01

Associated with commercial nuclear power production in the United States is the generation of potentially hazardous radioactive wastes. The Department of Energy (DOE) is seeking to develop nuclear waste isolation systems in geologic formations that will preclude contact with the biosphere of waste radionuclides in concentrations which are sufficient to cause deleterious impact on humans or their environments. Comprehensive analyses of specific isolation systems are needed to assess the expectations of meeting that objective. The Waste Isolation Safety Assessment Program (WISAP) has been established at the Pacific Northwest Laboratory (operated by Battelle Memorial Institute) for developing the capability of making those analyses. Progress on the following tasks is reported: release scenario analysis, waste form release rate analysis, release consequence analysis, sorption-desorption analysis, and societal acceptance analysis. (DC)

Internal Consistency of General Outcome Measures in Grades 1-8. Technical Report # 0915

Science.gov (United States)

Anderson, Daniel; Tindal, Gerald; Alonzo, Julie

2009-01-01

We developed alternate forms of a math test for use in both screening students at risk of failure and monitoring their progress over time. In this technical report, we present results of the screener, used in the fall of 2009. The 48-item test was aligned to the National Council of Teachers of Mathematics (NCTM) Curriculum Focal Point Standards…

Progress Report 2004-2005

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-11-01

The Faculty of Electrical Engineering and Computing (FER) as a part of University of Zagreb, has its roots in the Technical Faculty Zagreb, founded in 1919, which evolved into the Faculty of Electrical Engineering in 1956 and was upgraded into the Faculty of Electrical Engineering and Computing in 1994. Due to the increasing progress and advances in electrical and electronic engineering as well as in computer science and information technologies, the Faculty has become the largest technical faculty and the leading educational and R and D institution in the fields of electrical engineering and computing in Croatia. More than 13000 graduate students, more than 1900 postgraduate students who received the Master degree and more than 540 students with PhD degree, are today's total numbers, which highlights our highly spirited activities in teaching. Additional to this number are also 3800 undergraduate students as well as about 500 graduates each year. Organised in 11 departments, the present educational staff comprises 130 professors and 200 teaching assistants and researchers operating in more than 60 laboratories and area of more than 35000 m{sup 2}. Education and research is the crucial factor determining the economic and social progress and equality of opportunity in our societies. It becomes even more so in the digital age in order to ensure life-long-learning and the emergence of new generations of creators, researchers and entrepreneurs and to empower playing an active role in the knowledge society. The experiences at the university level should be transferred to the others. We can help to do that, as a chain the global challenge. The Faculty offers a broad spectrum of services to business and industry, from research and consultancy to conference facilities, training and postgraduate recruitment. The Faculty is a leading research-led institution and undertakes research at the highest levels of international standing. The Faculty is an integral part of the

Progress Report 2004-2005

International Nuclear Information System (INIS)

2005-11-01

The Faculty of Electrical Engineering and Computing (FER) as a part of University of Zagreb, has its roots in the Technical Faculty Zagreb, founded in 1919, which evolved into the Faculty of Electrical Engineering in 1956 and was upgraded into the Faculty of Electrical Engineering and Computing in 1994. Due to the increasing progress and advances in electrical and electronic engineering as well as in computer science and information technologies, the Faculty has become the largest technical faculty and the leading educational and R and D institution in the fields of electrical engineering and computing in Croatia. More than 13000 graduate students, more than 1900 postgraduate students who received the Master degree and more than 540 students with PhD degree, are today's total numbers, which highlights our highly spirited activities in teaching. Additional to this number are also 3800 undergraduate students as well as about 500 graduates each year. Organised in 11 departments, the present educational staff comprises 130 professors and 200 teaching assistants and researchers operating in more than 60 laboratories and area of more than 35000 m 2 . Education and research is the crucial factor determining the economic and social progress and equality of opportunity in our societies. It becomes even more so in the digital age in order to ensure life-long-learning and the emergence of new generations of creators, researchers and entrepreneurs and to empower playing an active role in the knowledge society. The experiences at the university level should be transferred to the others. We can help to do that, as a chain the global challenge. The Faculty offers a broad spectrum of services to business and industry, from research and consultancy to conference facilities, training and postgraduate recruitment. The Faculty is a leading research-led institution and undertakes research at the highest levels of international standing. The Faculty is an integral part of the community

High temperature phase equilibria and phase diagrams

CERN Document Server

Kuo, Chu-Kun; Yan, Dong-Sheng

2013-01-01

High temperature phase equilibria studies play an increasingly important role in materials science and engineering. It is especially significant in the research into the properties of the material and the ways in which they can be improved. This is achieved by observing equilibrium and by examining the phase relationships at high temperature. The study of high temperature phase diagrams of nonmetallic systems began in the early 1900s when silica and mineral systems containing silica were focussed upon. Since then technical ceramics emerged and more emphasis has been placed on high temperature

Plant Materials Program: progress June 1981-May 1982

International Nuclear Information System (INIS)

Childs, W.; Cubicciotti, D.; Fox, M.; Giannuzzi, A.; Gilman, J.; Jones, R.

1983-02-01

This is the second annual progress report of the Plant Materials Subprogram, which was organized in May 1980 to address corrosion-related materials problems in light water reactors. The first section of the report provides an overview of plant materials problems which have impact on plant availability. These include pipe and pressure vessel cracking, condenser leakage, turbine disc cracking, steam generator tube attack and cracking, and cracking of nickel alloy springs, beams and pins. The status and goals of research and development work related to each of these problems are reviewed briefly. Subsequent report sections provide more detailed reviews of significant progress in the relevant technical topic area: integranular stress corrosion cracking of austenitic stainless steels; environmentally-assisted cracking of carbon and low alloy steels; intergranular stress corrosion cracking of nickel-base alloys; and improved fabrication technology

Predictors of employer satisfaction: technical and non-technical skills.

Science.gov (United States)

Danielson, Jared A; Wu, Tsui-Feng; Fales-Williams, Amanda J; Kirk, Ryan A; Preast, Vanessa A

2012-01-01

Employers of 2007-2009 graduates from Iowa State University College of Veterinary Medicine were asked to respond to a survey regarding their overall satisfaction with their new employees as well as their new employees' preparation in several technical and non-technical skill areas. Seventy-five responses contained complete data and were used in the analysis. Four technical skill areas (data collection, data interpretation, planning, and taking action) and five non-technical skill areas (interpersonal skills, ability to deal with legal issues, business skills, making referrals, and problem solving) were identified. All of the skill area subscales listed above had appropriate reliability (Cronbach's alpha>0.70) and were positively and significantly correlated with overall employer satisfaction. Results of two simultaneous regression analyses indicated that of the four technical skill areas, taking action is the most salient predictor of employer satisfaction. Of the five non-technical skill areas, interpersonal skills, business skills, making referrals, and problem solving were the most important skills in predicting employer satisfaction. Hierarchical regression analysis revealed that all technical skills explained 25% of the variation in employer satisfaction; non-technical skills explained an additional 42% of the variation in employer satisfaction.

Optically pumped polarized 23Na vapor target for use in polarized ion source. Technical progress report

International Nuclear Information System (INIS)

Anderson, L.W.

1984-01-01

We are currently measuring relaxation times in an optically pumped 23 Na vapor target. Our research is directed toward improvements in the optically pumped Na vapor targets used for the production of polarized H - ions. In this progress report we review the properties of the optically pumped polarized H - ion source and especially the optically pumped Na vapor target employed in this source as well as discussing the progress of our research on relaxation times in an optically pumped Na vapor target. 30 references, 6 figures, 3 tables

Scaling Studies for Advanced High Temperature Reactor Concepts, Final Technical Report: October 2014—December 2017

Energy Technology Data Exchange (ETDEWEB)

Woods, Brian; Gutowska, Izabela; Chiger, Howard

2018-03-26

Computer simulations of nuclear reactor thermal-hydraulic phenomena are often used in the design and licensing of nuclear reactor systems. In order to assess the accuracy of these computer simulations, computer codes and methods are often validated against experimental data. This experimental data must be of sufficiently high quality in order to conduct a robust validation exercise. In addition, this experimental data is generally collected at experimental facilities that are of a smaller scale than the reactor systems that are being simulated due to cost considerations. Therefore, smaller scale test facilities must be designed and constructed in such a fashion to ensure that the prototypical behavior of a particular nuclear reactor system is preserved. The work completed through this project has resulted in scaling analyses and conceptual design development for a test facility capable of collecting code validation data for the following high temperature gas reactor systems and events— 1. Passive natural circulation core cooling system, 2. pebble bed gas reactor concept, 3. General Atomics Energy Multiplier Module reactor, and 4. prismatic block design steam-water ingress event. In the event that code validation data for these systems or events is needed in the future, significant progress in the design of an appropriate integral-type test facility has already been completed as a result of this project. Where applicable, the next step would be to begin the detailed design development and material procurement. As part of this project applicable scaling analyses were completed and test facility design requirements developed. Conceptual designs were developed for the implementation of these design requirements at the Oregon State University (OSU) High Temperature Test Facility (HTTF). The original HTTF is based on a ¼-scale model of a high temperature gas reactor concept with the capability for both forced and natural circulation flow through a prismatic core with

Safety research programs sponsored by Office of Nuclear Regulatory Research: Progress report, July 1--September 30, 1988

Energy Technology Data Exchange (ETDEWEB)

Weiss, A J [comp.

1989-02-01

This progress report describes current activities and technical progress in the programs at Brookhaven National Laboratory sponsored by the Division of Regulatory Applications, Division of Engineering, Division of Safety Issue Resolution, and Division of Systems of the US Nuclear Regulatory Commission, Office of Nuclear Regulatory Research following the reorganization in July 1988. The previous reports have covered the period October 1, 1976 through June 30, 1988. 71 figs., 24 tabs.

Safety research programs sponsored by Office of Nuclear Regulatory Research: Progress report, July 1--September 30, 1988

International Nuclear Information System (INIS)

Weiss, A.J.

1989-02-01

This progress report describes current activities and technical progress in the programs at Brookhaven National Laboratory sponsored by the Division of Regulatory Applications, Division of Engineering, Division of Safety Issue Resolution, and Division of Systems of the US Nuclear Regulatory Commission, Office of Nuclear Regulatory Research following the reorganization in July 1988. The previous reports have covered the period October 1, 1976 through June 30, 1988. 71 figs., 24 tabs

Technical standards in the law of technical safety

International Nuclear Information System (INIS)

Marburger, P.

1985-01-01

Technical standards are of great importance for the closer definition of inexact terms of law, for instance ''generally accepted technical rules'', ''state of the art'', ''state of science and technology'' or similar normative terms, in the law of technical safety. The paper discusses with whom the authority for regulating this sector of law rests, deals with the different ways of how technical standards are used by the law (''anticipated expert opinion'', reference to such standards in law and administration) and points out demands on the procedure of standardization. (orig.) [de

Association Euratom - Risoe National Laboratory, Technical Univ. of Denmark. Annual progress report 2007

Energy Technology Data Exchange (ETDEWEB)

Michelsen, P.K.; Korsholm, S.B.; Rasmussen, J.J. (eds.)

2008-04-15

The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. The activities in technology on investigations of radiation damage of fusion reactor materials have been phased out during 2007. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2007. (Author)

Association Euratom - Risoe National Laboratory, Technical Univ. of Denmark. Annual progress report 2007

International Nuclear Information System (INIS)

Michelsen, P.K.; Korsholm, S.B.; Rasmussen, J.J.

2008-04-01

The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. The activities in technology on investigations of radiation damage of fusion reactor materials have been phased out during 2007. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2007. (Author)

High-Temperature Air-Cooled Power Electronics Thermal Design: Annual Progress Report

Energy Technology Data Exchange (ETDEWEB)

Waye, Scot [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2016-08-01

Power electronics that use high-temperature devices pose a challenge for thermal management. With the devices running at higher temperatures and having a smaller footprint, the heat fluxes increase from previous power electronic designs. This project overview presents an approach to examine and design thermal management strategies through cooling technologies to keep devices within temperature limits, dissipate the heat generated by the devices and protect electrical interconnects and other components for inverter, converter, and charger applications. This analysis, validation, and demonstration intends to take a multi-scale approach over the device, module, and system levels to reduce size, weight, and cost.

New imaging systems in nuclear medicine. Technical progress report, July 1, 1975--March 15, 1976

International Nuclear Information System (INIS)

Brownell, G.L.

1976-01-01

This progress report covers four areas: development of positron instrumentation, development of NUMEDICS computer system and software, application of cyclotron-produced isotopes ( 11 C, 68 Ga, 13 N, 15 O, and 82 Rb), and application of the NUMEDICS computer system in nuclear medicine. The development of transverse section positron imaging has had a significant impact and a positron camera was designed specifically for transverse section imaging of heart and lungs. The computer net (NUMEDICS II) is progressing rapidly in design and software development. Clinical studies have demonstrated the feasibility of measuring cerebral blood flow using a variety of positron emitting radiopharmaceuticals and oxygen utilization using 15 O 2 . Rubidium-82 also appears to be a promising agent for measurement of cerebral blood flow

Research Progress and Development of Sapphire Fiber Sensor

Directory of Open Access Journals (Sweden)

Guochang ZHAO

2014-07-01

Full Text Available Sapphire fiber thermometers have become a new potential option in the field of high-temperature measurements. Recent research progress of sapphire fiber sensors is summarized; operational principles, advantages, disadvantages, and applications of sapphire fiber sensors are introduced. Research has shown that sapphire fiber sensors can be used to accurately measure very high temperatures in harsh environments and has been widely applied in fields such as aviation, metallurgy, the chemical industry, energy, and other high temperature measurement areas. Sapphire optical fiber temperature measurement technology will move toward miniaturization, intelligence following the advances in materials, micro-fabrication and communication technologies.

U.S. TIMSS and PIRLS 2011 Technical Report and User's Guide. NCES 2013-046

Science.gov (United States)

Kastberg, David; Roey, Stephen; Ferraro, David; Lemanski, Nita; Erberber, Ebru

2013-01-01

The "U.S. TIMSS and PIRLS 2011 Technical Report and User's Guide" provides an overview of the design and implementation of the Trends in International Mathematics and Science Study (TIMSS) 2011 and the Progress in International Reading Literacy Study (PIRLS) 2011 in the United States and the nine participating benchmarking states:…

The Development of the easyCBM CCSS Reading Assessments: Grade 3. Technical Report #1221

Science.gov (United States)

Alonzo, Julie; Park, Bitnara Jasmine; Tindal, Gerald

2012-01-01

In this technical report, we document the development and piloting of easyCBM reading measures aligned to the Common Core State Standards, designed for use in screening students at risk for reading difficulty and monitoring their progress as they develop reading skills. The measures, which assess students' ability to respond to…

Current progress and technical challenges of flexible liquid crystal displays

Science.gov (United States)

Fujikake, Hideo; Sato, Hiroto

2009-02-01

We focused on several technical approaches to flexible liquid crystal (LC) display in this report. We have been developing flexible displays using plastic film substrates based on polymer-dispersed LC technology with molecular alignment control. In our representative devices, molecular-aligned polymer walls keep plastic-substrate gap constant without LC alignment disorder, and aligned polymer networks create monostable switching of fast-response ferroelectric LC (FLC) for grayscale capability. In the fabrication process, a high-viscosity FLC/monomer solution was printed, sandwiched and pressed between plastic substrates. Then the polymer walls and networks were sequentially formed based on photo-polymerization-induced phase separation in the nematic phase by two exposure processes of patterned and uniform ultraviolet light. The two flexible backlight films of direct illumination and light-guide methods using small three-primary-color light-emitting diodes were fabricated to obtain high-visibility display images. The fabricated flexible FLC panels were driven by external transistor arrays, internal organic thin film transistor (TFT) arrays, and poly-Si TFT arrays. We achieved full-color moving-image displays using the flexible FLC panel and the flexible backlight film based on field-sequential-color driving technique. Otherwise, for backlight-free flexible LC displays, flexible reflective devices of twisted guest-host nematic LC and cholesteric LC were discussed with molecular-aligned polymer walls. Singlesubstrate device structure and fabrication method using self-standing polymer-stabilized nematic LC film and polymer ceiling layer were also proposed for obtaining LC devices with excellent flexibility.